Surface-subsurface turbulent interaction at the interface of a permeable bed: influence of the wall permeability

Science.gov (United States)

Kim, T.; Blois, G.; Best, J.; Christensen, K. T.

2017-12-01

Coarse-gravel river beds possess a high degree of permeability. Flow interactions between surface and subsurface flow across the bed interface is key to a number of natural processes occurring in the hyporheic zone. In fact, it is increasingly recognized that these interactions drive mass, momentum and energy transport across the interface, and consequently control biochemical processes as well as stability of sediments. The current study explores the role of the wall permeability in surface and subsurface flow interaction under controlled experimental conditions on a physical model of a gravel bed. The present wall model was constructed by five layers of cubically arranged spheres (d=25.4mm, where d is a diameter) providing 48% of porosity. Surface topography was removed by cutting half of a diameter on the top layer of spheres to render the flow surface smooth and highlight the impact of the permeability on the overlying flow. An impermeable smooth wall was also considered as a baseline of comparison for the permeable wall flow. To obtain basic flow statistics, low-frame-rate high-resolution PIV measurements were performed first in the streamwise-wall-normal (x-y) plane and refractive-index matching was employed to optically access the flow within the permeable wall. Time-resolved PIV experiments in the same facility were followed to investigate the flow interaction across the wall interface in sptaio-temporal domain. In this paper, a detailed analysis of the first and second order velocity statistics as well as the amplitude modulation for the flow overlying the permeable smooth wall will be presented.

Sub-core permeability and relative permeability characterization with Positron Emission Tomography

Science.gov (United States)

Zahasky, C.; Benson, S. M.

2017-12-01

This study utilizes preclinical micro-Positron Emission Tomography (PET) to image and quantify the transport behavior of pulses of a conservative aqueous radiotracer injected during single and multiphase flow experiments in a Berea sandstone core with axial parallel bedding heterogeneity. The core is discretized into streamtubes, and using the micro-PET data, expressions are derived from spatial moment analysis for calculating sub-core scale tracer flux and pore water velocity. Using the flux and velocity data, it is then possible to calculate porosity and saturation from volumetric flux balance, and calculate permeability and water relative permeability from Darcy's law. Full 3D simulations are then constructed based on this core characterization. Simulation results are compared with experimental results in order to test the assumptions of the simple streamtube model. Errors and limitations of this analysis will be discussed. These new methods of imaging and sub-core permeability and relative permeability measurements enable experimental quantification of transport behavior across scales.

Experimental Study on the Effects of Stress Variations on the Permeability of Feldspar-Quartz Sandstone

Directory of Open Access Journals (Sweden)

Fugang Wang

2017-01-01

Full Text Available The multistage and discontinuous nature of the injection process used in the geological storage of CO2 causes reservoirs to experience repeated loading and unloading. The reservoir permeability changes caused by this phenomenon directly impact the CO2 injection process and the process of CO2 migration in the reservoirs. Through laboratory experiments, variations in the permeability of sandstone in the Liujiagou formation of the Ordos CO2 capture and storage (CCS demonstration project were analyzed using cyclic variations in injection pressure and confining pressure and multistage loading and unloading. The variation in the micropore structure and its influence on the permeability were analyzed based on micropore structure tests. In addition, the effects of multiple stress changes on the permeability of the same type of rock with different clay minerals content were also analyzed. More attention should be devoted to the influence of pressure variations on permeability in evaluations of storage potential and studies of CO2 migration in reservoirs in CCS engineering.

The sedimentology of uranium-bearing sandstones on the farm Kaffersfontein 328, Beaufort West area

International Nuclear Information System (INIS)

Cole, D.I.

1979-10-01

The sedimentology of uranium-bearing sandstones on the farm Kaffersfontein 328 was studied by use of 23 vertical profiles measured across and adjacent to 3 mineralised deposits. The profiles consist of 18 field sections and 5 borehole logs. The vertical profiles basically consist of a succession of sedimentary facies. A total of 18 facies were recognised within the fluvial sandstone sequence according to the criteria of grain-size and sedimentary structures. Transitions between the facies were subjected to a Markov chain analysis in order to delineate Markov-dependent transitions. Uranium mineralisation coincides with areas of thicker sandstone, usually where channel over-deepening has taken place. It always occurs above the base of a channel, which often marks the base of the fluvial sandstone sequence. Irregularities in the base of the channel probably caused interruptions to the flow of uraniferous solutions and allowed sufficient time for the precipitation of the uranium. Carbonaceous debris is always associated with the mineralisation and most likely acted as an indirect reductant for the precipitation of uranium from solution. The direct reductant was most probably H 2 S produced by anaerobic bacteria acting on the carbonaceous debris. The mineralisation is confined to the coarser-grained sedimentary facies, which suggests that permeability was an important control on the mineralisation. These facies probably acted as suitable aquifers for the transport of uraniferous solutions. Horizontally bedded sandstone facies comprises 41 per cent of the total cumulative thickness of mineralisation. This facies represents a higher stream power and may consequently contain more carbonaceous material derived from plants, which were eroded from upstream areas. The nature of the bedding may also have provided a more effective permeability zone for the transport of uraniferous solutions prior to precipitation of the uranium

ANALYSIS OF OIL-BEARING CRETACEOUS SANDSTONE HYDROCARBON RESERVOIRS, EXCLUSIVE OF THE DAKOTA SANDSTONE, ON THE JICARILLA APACHE INDIAN RESERVATION, NEW MEXICO

International Nuclear Information System (INIS)

Jennie Ridgley

2000-01-01

A goal of the Mesaverde project was to better define the depositional system of the Mesaverde in hopes that it would provide insight to new or by-passed targets for oil exploration. The new, detailed studies of the Mesaverde give us a better understanding of the lateral variability in depositional environments and facies. Recognition of this lateral variability and establishment of the criteria for separating deltaic, strandplain-barrier, and estuarine deposits from each other permit development of better hydrocarbon exploration models, because the sandstone geometry differs in each depositional system. Although these insights will provide better exploration models for gas exploration, it does not appear that they will be instrumental in finding more oil. Oil in the Mesaverde Group is produced from isolated fields on the Chaco slope; only a few wells define each field. Production is from sandstone beds in the upper part of the Point Lookout Sandstone or from individual fluvial channel sandstones in the Menefee. Stratigraphic traps rather than structural traps are more important. Source of the oil in the Menefee and Point Lookout may be from interbedded organic-rich mudstones or coals rather than from the Lewis Shale. The Lewis Shale appears to contain more type III organic matter and, hence, should produce mainly gas. Outcrop studies have not documented oil staining that might point to past oil migration through the sandstones of the Mesaverde. The lack of oil production may be related to the following: (1) lack of abundant organic matter of the type I or II variety in the Lewis Shale needed to produce oil, (2) ineffective migration pathways due to discontinuities in sandstone reservoir geometries, (3) cementation or early formation of gas prior to oil generation that reduced effective permeabilities and served as barriers to updip migration of oil, or (4) erosion of oilbearing reservoirs from the southern part of the basin. Any new production should mimic that of

Characterizing flow pathways in a sandstone aquifer: Tectonic vs sedimentary heterogeneities

Science.gov (United States)

Medici, G.; West, L. J.; Mountney, N. P.

2016-11-01

Sandstone aquifers are commonly assumed to represent porous media characterized by a permeable matrix. However, such aquifers may be heavy fractured when rock properties and timing of deformation favour brittle failure and crack opening. In many aquifer types, fractures associated with faults, bedding planes and stratabound joints represent preferential pathways for fluids and contaminants. In this paper, well test and outcrop-scale studies reveal how strongly lithified siliciclastic rocks may be entirely dominated by fracture flow at shallow depths (≤ 180 m), similar to limestone and crystalline aquifers. However, sedimentary heterogeneities can primarily control fluid flow where fracture apertures are reduced by overburden pressures or mineral infills at greater depths. The Triassic St Bees Sandstone Formation (UK) of the East Irish Sea Basin represents an optimum example for study of the influence of both sedimentary and tectonic aquifer heterogeneities in a strongly lithified sandstone aquifer-type. This fluvial sedimentary succession accumulated in rapidly subsiding basins, which typically favours preservation of complete depositional cycles including fine grained layers (mudstone and silty sandstone) interbedded in sandstone fluvial channels. Additionally, vertical joints in the St Bees Sandstone Formation form a pervasive stratabound system whereby joints terminate at bedding discontinuities. Additionally, normal faults are present through the succession showing particular development of open-fractures. Here, the shallow aquifer (depth ≤ 180 m) was characterized using hydro-geophysics. Fluid temperature, conductivity and flow-velocity logs record inflows and outflows from normal faults, as well as from pervasive bed-parallel fractures. Quantitative flow logging analyses in boreholes that cut fault planes indicate that zones of fault-related open fractures characterize 50% of water flow. The remaining flow component is dominated by bed-parallel fractures

Biofilm Effect on Flow Structure over a Permeable Bed

Science.gov (United States)

Kazemifar, F.; Blois, G.; Aybar, M.; Perez-Calleja, P.; Nerenberg, R.; Sinha, S.; Hardy, R. J.; Best, J.; Sambrook Smith, G.; Christensen, K. T.

2017-12-01

Biofilms constitute an important form of bacterial life in aquatic environments and are present at the fluid-solid interfaces in natural and industrial settings, such as water distribution systems and riverbeds among others. The permeable, heterogeneous, and deformable structure of biofilms can influence mass and momentum transport between the subsurface and freestream. However, this interaction is not fully understood, in part due to technical obstacles impeding quantitative experimental investigations. In this work, the effect of biofilm on flow structure over a permeable bed is studied. Experiments are conducted in a closed water channel equipped with an idealized two-dimensional permeable bed. Prior to conducting flow experiments, the models are placed within an independent recirculating reactor for biofilm growth. Once a targeted biofilm growth stage is achieved, the models are transferred to the water channel and subjected to transitional and turbulent flows. Long-distance microscopic particle image velocimetry measurements are performed to quantify the effect of biofilm on the turbulence structure of the free flow as well as the freestream-subsurface flow interaction.

Exploration of method determining hydrogeologic parameters of low permeability sandstone uranium deposits

International Nuclear Information System (INIS)

Ji Hongbin; Wu Liwu; Cao Zhen

2012-01-01

A hypothesis of regarding injecting test as 'anti-pumping' test is presented, and pumping test's 'match line method' is used to process data of injecting test. Accurate hydrogeologic parameters can be obtained by injecting test in the sandstone uranium deposits with low permeability and small pumping volume. Taking injecting test in a uranium deposit of Xinjiang for example, the hydrogeologic parameters of main ore-bearing aquifer were calculated by using the 'anti-pumping' hypothesis. Results calculated by the 'anti-pumping' hypothesis were compared with results calculated by water level recovery method. The results show that it is feasible to use 'anti-pumping' hypothesis to calculate the hydrogeologic parameters of main ore-bearing aquifer. (authors)

The sedimentology of uranium-bearing sandstones on the farm Riet Kuil 307, Beaufort West area

International Nuclear Information System (INIS)

Cole, D.I.

1980-10-01

The sedimentology of four sandstones was studied in outcrop and in the subsurface on the farm Riet Kuil 307, near Beaufort West. Only two of these sandstones are mineralised. These are four surface and two subsurface uranium anomalies and one surface uranium anomaly. The sedimentological study was made by means of 47 vertical profiles measured across and adjacent to the surface anomalies as well as 11 core-logs, which intersected the subsurface anomalies. The unmineralised sandstones are included in this study. A total of 19 sedimentary facies was recognised within the fluvial sandstone sequence according to the criteria of grain-size and sedimentary structure. Transitions between the facies were subjected to a Markov chain analysis in order to delineate Markov-dependent transitions. Uranium mineralisation is almost entirely confined to the coarser-grained sedimentary facies, which probably acted as suitable aquifers for the transport of uraniferous solutions prior to the precipitation of the uranium. Horizontally bedded sandstone facies comprises 60 per cent of the total cumulative thickness of mineralisation. The nature of the bedding of this facies may have provided a more effective permeability zone for the transport of uraniferous solutions. This facies contains an abundance of carbonaceous material which acted as an important indirect reductant for the precipitation of uranium from solution. The direct reductant was most probably H 2 S produced by enaerobic bacteria acting on this carbonaceous material shortly after deposition of the sediments. Carbonaceous material also occurs in the other mineralised facies and is considered to be the major control on the mineralisation in the uranium-bearing sandstones

Experimental Studies on Permeability of Intact and Singly Jointed Meta-Sedimentary Rocks Under Confining Pressure

Science.gov (United States)

Wong, Louis Ngai Yuen; Li, Diyuan; Liu, Gang

2013-01-01

Three different types of permeability tests were conducted on 23 intact and singly jointed rock specimens, which were cored from rock blocks collected from a rock cavern under construction in Singapore. The studied rock types belong to inter-bedded meta-sandstone and meta-siltstone with very low porosity and high uniaxial compressive strength. The transient pulse water flow method was employed to measure the permeability of intact meta-sandstone under a confining pressure up to 30 MPa. It showed that the magnitude order of meta-sandstone's intrinsic permeability is about 10-18 m2. The steady-state gas flow method was used to measure the permeability of both intact meta-siltstone and meta-sandstone in a triaxial cell under different confining pressures spanning from 2.5 to 10 MPa. The measured permeability of both rock types ranged from 10-21 to 10-20 m2. The influence of a single natural joint on the permeability of both rock types was studied by using the steady-state water flow method under different confining pressures spanning from 1.25 to 5.0 MPa, including loading and unloading phases. The measured permeability of both jointed rocks ranged from 10-13 to 10-11 m2, where the permeability of jointed meta-siltstone was usually slightly lower than that of jointed meta-sandstone. The permeability of jointed rocks decreases with increasing confining pressure, which can be well fitted by an empirical power law relationship between the permeability and confining pressure or effective pressure. The permeability of partly open cracked specimens is lower than that of open cracked specimens, but it is higher than that of the specimen with a dominant vein for the meta-sandstone under the same confining pressure. The permeability of open cracked rock specimens will partially recover during the unloading confining pressure process. The equivalent crack (joint) aperture is as narrow as a magnitude order of 10-6 m (1 μm) in the rock specimens under confining pressures

Seal evaluation and confinement screening criteria for beneficial carbon dioxide storage with enhanced coal bed methane recovery in the Pocahontas Basin, Virginia

Science.gov (United States)

Grimm, R.P.; Eriksson, K.A.; Ripepi, N.; Eble, C.; Greb, S.F.

2012-01-01

The geological storage of carbon dioxide in Appalachian basin coal seams is one possible sink for sequestration of greenhouse gases, with the added benefit of enhanced-coal bed methane (ECBM) recovery. The Pocahontas Basin (part of the central Appalachian Basin) of southwestern Virginia is a major coal bed methane (CBM) province with production mostly from coal beds in the Lower Pennsylvanian Pocahontas and New River formations. As part of the Southeast Regional Carbon Sequestration Partnership's Phase II research program, a CO 2-injection demonstration well was installed into Lower Pennsylvanian coal bed-methane producing strata in southwest Virginia. Samples of siliciclastic lithologies above coal beds in this Oakwood Field well, and from several other cores in the Nora Field were taken to establish a baseline of the basic confinement properties of overlying strata to test seal competency at local and regional scales.Strata above CBM-producing coal beds in the Pocahontas and New River formations consist of dark-gray shales; silty gray shales; heterolithic siltstones, sandstones, and shales; lithic sandstones, and quartzose sandstones. Standard measurements of porosity, permeability and petrography were used to evaluate potential leakage hazards and any possible secondary storage potential for typical lithologies. Both lithic- and quartz-rich sandstones exhibit only minor porosity, with generally low permeability (Member. Analyses of 1500 geophysical logs in southwest Virginia indicate that this unit is moderately thick (>50ft, 15m), laterally continuous (>3000km 2), and a homogenous shale, which coarsens upward into siltstone and sandstone, or is truncated by sandstone. Calculations from two mercury injection capillary porosimetry tests of the shale indicate that a displacement entry pressure of 207psi (1427kPa) would generate an estimated seal capacity of 1365ft (416m) of CO 2 before buoyant leakage. Scanning electron microscopy indicates a microfabric of narrow

INTRODUCTION Sandstone beds within Auchi locality are the ...

African Journals Online (AJOL)

The major framework composition is Q F L which classifies the sandstone as Quartz ... The grains are texturally immature as depicted by their subangular edges but mineralogically ..... Fig 6 : Vertical Section of Bioturbated Sandstone Lithofacies Showing Trace Fossils ..... on Water Quality and Planktonic Production in an.

Study of lixiviant damage of a sandstone deposit during in-situ leaching of uranium

International Nuclear Information System (INIS)

Liao Wensheng; Wang Limin; Jiang Yan; Jiang Guoping; Tan Yahui

2014-01-01

The permeability of sandstone deposit is a key factor for economical uranium recovery during in-situ leaching uranium. Low permeability sandstone uranium deposits behave low push-pull capacity, and show formation damage in leaching operations. It is important to study formation damage of permeability, therefore, and to stabilize even improve the push-pull power of drillholes during in-situ leaching. In this paper, formation damage caused by lixiviants was investigated based on a low permeability sandstone uranium deposit. The resulted showed that, under the conditions of in-situ leaching, the salinity of leaching fluid has no harm to formation permeability, on the contrary, the increment of salinity of lixiviant during in-situ leaching improve the permeability of the deposit. The alkalinity, hydrogen peroxide and productivity of the lixiviant cause no significant formation damage. But the fine particles in the lixiviant shows formation damage significantly, and the quantity of the particles should be controlled during production. (authors)

Effect of CH4 on the CO2 breakthrough pressure and permeability of partially saturated low-permeability sandstone in the Ordos Basin, China

Science.gov (United States)

Zhao, Yan; Yu, Qingchun

2018-01-01

The behavior of CO2 that coexists with CH4 and the effect of CH4 on the CO2 stream need to be deeply analyzed and studied, especially in the presence of water. Our previous studies investigated the breakthrough pressure and permeability of pure CO2 in five partially saturated low-permeability sandstone core samples from the Ordos Basin, and we concluded that rocks with a small pore size and low permeability show considerable sealing capacity even under unsaturated conditions. In this paper, we selected three of these samples for CO2-CH4 gas-mixture breakthrough experiments under various degrees of water saturation. The breakthrough experiments were performed by increasing the gas pressure step by step until breakthrough occurred. Then, the effluent gas mixture was collected for chromatographic partitioning analysis. The results indicate that CH4 significantly affects the breakthrough pressure and permeability of CO2. The presence of CH4 in the gas mixture increases the interfacial tension and, thus, the breakthrough pressure. Therefore, the injected gas mixture that contains the highest (lowest) mole fraction of CH4 results in the largest (smallest) breakthrough pressure. The permeability of the gas mixture is greater than that for pure CO2 because of CH4, and the effective permeability decreases with increased breakthrough pressure. Chromatographic partitioning of the effluent mixture gases indicates that CH4 breaks through ahead of CO2 as a result of its weaker solubility in water. Correlations are established between (1) the breakthrough pressure and water saturation, (2) the effective permeability and water saturation, (3) the breakthrough pressure and effective permeability, and (4) the mole fraction of CO2/CH4 in the effluent mixture gases and water saturation. These results deepen our understanding of the multi-phase flow behavior in the porous media under unsaturated conditions, which have implications for formulating emergency response plans for gas

Emplacement processes of tuffaceous sandstones at IODP Site C0011B, Nankai Trough, derived from modal analysis

Science.gov (United States)

Schindlbeck, J. C.; Kutterolf, S.; Freundt, A.

2011-12-01

Tuffaceous sandstones are characterized by their high amount (25 to 75%) of pyroclasts in their modal composition. During IODP Expedition 322 three interbeds of tuffaceous sandstones have been found within a moderately lithified and bioturbated silty claystone sequence in the late Miocene (>7.07 to ~9.0 Ma) upper part of the middle Shikoku Basin facies. Of the three sandstones, units 1 and 2 are single beds whereas unit 3 is composed of three beds. Modal analyses of 29 sandstone thin sections reveal systematic vertical changes within each bed. Generally low-density pyroclasts are enriched at the top (50-60 vol%) of each sandstone bed whereas dense lithic components (25-30 vol%) and minerals (25-30 vol%) are enriched at the bottom. The vertically varying abundance of various types of lithic fragments (sedimentary, volcanoclastic and metamorphic) suggests that these have also been segregated according to their respective densities. The highest amount of fine-grained matrix glass is found in the middle of each bed. Pumice and lithic fragments in the middle and upper parts of the sandstone beds carry ash coatings. For sandstone package 3, in contrast to 1 and 2, core pictures and thin section analyses indicate a subdivision in three units showing the same significant variations in top to bottom enrichment. This suggests three sedimentation events following each other in short time intervals. Glass and mineral chemistry of each sandstone bed show no significant vertical variations. Specifically the matrix glass-shard major element compositions are identical to the pumice clast composition in each tuffaceous sandstone bed. The compositions of amphibole and pyroxene crystals differ only slightly between the sandstone packages. Application of the Ridolfi et al. (2009) thermobarometric calculations to amphiboles of sandstone packages 1 and 2 suggests that each of these was derived from a volcanic system comprising both a deep and a shallow magma reservoir. Thickness and

Lattice strain measurements on sandstones under load using neutron diffraction

Science.gov (United States)

Frischbutter, A.; Neov, D.; Scheffzük, Ch.; Vrána, M.; Walther, K.

2000-11-01

Neutron diffraction methods (both time-of-flight- and angle-dispersive diffraction) are applied to intracrystalline strain measurements on geological samples undergoing uniaxial increasing compressional load. The experiments were carried out on Cretaceous sandstones from the Elbezone (East Germany), consisting of >95% quartz which are bedded but without crystallographic preferred orientation of quartz. From the stress-strain relation the Young's modulus for our quartz sample was determined to be (72.2±2.9) GPa using results of the neutron time-of-flight method. The influence of different kinds of bedding in sandstones (laminated and convolute bedding) could be determined. We observed differences of factor 2 (convolute bedding) and 3 (laminated bedding) for the elastic stiffness, determined with angle dispersive neutron diffraction (crystallographic strain) and with strain gauges (mechanical strain). The data indicate which geological conditions may influence the stress-strain behaviour of geological materials. The influence of bedding on the stress-strain behaviour of a laminated bedded sandstone was indicated by direct residual stress measurements using neutron time-of-flight diffraction. The measurements were carried out six days after unloading the sample. Residual strain was measured for three positions from the centre to the periphery and within two radial directions of the cylinder. We observed that residual strain changes from extension to compression in a different manner for two perpendicular directions of the bedding plane.

The experimental modeling of gas percolation mechanisms in a coal-measure tight sandstone reservoir: A case study on the coal-measure tight sandstone gas in the Upper Triassic Xujiahe Formation, Sichuan Basin, China

Directory of Open Access Journals (Sweden)

Shizhen Tao

2016-12-01

Full Text Available Tight sandstone gas from coal-measure source rock is widespread in China, and it is represented by the Xujiahe Formation of the Sichuan Basin and the Upper Paleozoic of the Ordos Basin. It is affected by planar evaporative hydrocarbon expulsion of coal-measure source rock and the gentle structural background; hydrodynamics and buoyancy play a limited role in the gas migration-accumulation in tight sandstone. Under the conditions of low permeability and speed, non-Darcy flow is quite apparent, it gives rise to gas-water mixed gas zone. In the gas displacing water experiment, the shape of percolation flow curve is mainly influenced by core permeability. The lower the permeability, the higher the starting pressure gradient as well as the more evident the non-Darcy phenomenon will be. In the gas displacing water experiment of tight sandstone, the maximum gas saturation of the core is generally less than 50% (ranging from 30% to 40% and averaging at 38%; it is similar to the actual gas saturation of the gas zone in the subsurface core. The gas saturation and permeability of the core have a logarithm correlation with a correlation coefficient of 0.8915. In the single-phase flow of tight sandstone gas, low-velocity non-Darcy percolation is apparent; the initial flow velocity (Vd exists due to the slippage effect of gas flow. The shape of percolation flow curve of a single-phase gas is primarily controlled by core permeability and confining pressure; the lower the permeability or the higher the confining pressure, the higher the starting pressure (0.02–0.08 MPa/cm, whereas, the higher the quasi-initial flow speed, the longer the nonlinear section and the more obvious the non-Darcy flow will be. The tight sandstone gas seepage mechanism study shows that the lower the reservoir permeability, the higher the starting pressure and the slower the flow velocity will be, this results in the low efficiency of natural gas migration and accumulation as well as

PETROFACIES CHARACTERISTICS OF THE SANDSTONES OF THE UPPER MIOCENELOWER PLIOCENE AGED IN THE ULUMUHSİNE-TATKÖY (KONYA AREA

Directory of Open Access Journals (Sweden)

A. Müjdat ÖZKAN

2000-03-01

Full Text Available In the study area, Upper Miocene-Lower Pliocene aged Ulumuhsine formation, was formed in a shallow, open lake and river environment. The lithologies of this formation are thin-medium bedded, laminated and fossil rich limestone, thin-thick bedded mudstone, thin-thick bedded marl, thin-thick bedded dolomite with stromatolite interbedded limestone, tuffite, chert bands and coal-rich levels. In addition, it includes conglomerates and sandstones of underwater distrubution channels in lacustrine, and channel and bar sediments in stream environments. Red, gray, rarely green colored sandstones are thin-thick bedded, and in some levels well sorting, in some levels proorly sorting. They present sedimentary structures, as graded, herringbone cross-bedding, symmetric ripple-marks, and laminate. Sandstones are named lithic arenite and lithic graywacke and litharenite, feldspathic litharenite and sublithic arenite. These sandstones are rich rock fragments and quartzs, in addition they contain plagioclase, biotite, muskovite, opaque mineral and epidote. Binding materials of sandstones are mainly calcite cements and clay matrix, and iron oxide cement in little amount. From the mineralogical and textural point of view. As a tectonic environment, the main source of sandstones are recycled orogen (thrust, collision and land uplift and recyded lithic fragments.

Sandstone-type uranium deposits

International Nuclear Information System (INIS)

Austin, S.R.; D'Andrea, R.F. Jr.

1978-01-01

Three overall factors are necessary for formation of uranium deposits in sandstone: a source of uranium, host rocks capable of transmitting uranium-bearing solutions, and a precipitant. Possible sources of uranium in sandstone-type deposits include groundwaters emanating from granitic highlands, arkosic sediments, tuffaceous material within or overlying the host rocks, connate fluids, and overlying black shales. The first three sources are considered the most likely. Host rocks are generally immature sandstones deposited in alluvial-fan, intermontane-basin or marginal-marine environments, but uranium deposits do occur in well-winnowed barrier-bar or eolian sands. Host rocks for uranium deposits generally show coefficients of permeability on the order of 1 to 100 gal/day/ft 2 . Precipitants are normally agents capable of reducing uranium from the uranyl to the uranous state. The association of uranium with organic matter is unequivocal; H 2 S, a powerful reductant, may have been present at the time of formation of some deposits but may go unnoticed today. Vanadium can serve to preserve the tabular characteristics of some deposits in the near-surface environment, but is considered an unlikely primary precipitant for uranium. Uranium deposits in sandstone are divided into two overall types: peneconcordant deposits, which occur in locally reducing environments in otherwise oxidized sandstones; and roll-type deposits, which occur at the margin of an area where an oxidized groundwater has permeated an otherwise reduced sandstone. Uranium deposits are further broken down into four subclasses; these are described

Petrographic characteristic of the sandstones of the upper paleocene-middle eocene aged in the Yildizli-Aydinkent (Ereğli-Konya area

Directory of Open Access Journals (Sweden)

A. Müjdat Özkan

2002-03-01

Full Text Available In the study area, Upper Paleocene - Middle Eocene aged Halkapınar formation, was formed in a shallow and deep marine environment. The lithologies of this formation are medium - thick bedded conglomerate, thin - thick bedded sandstone, thin - very thick bedded shale, thin - medium bedded marl with chert nodules and bands. In addition olistolithes of ophiolitic melange are found at the top of the sandstones, which includes basalt interbands. Yellowish gray, greenish gray, beige, gray colored sandstones include some sedimentary structures, namely ripple - marks, graded bedding, laminate, convolute lamination, current ripple, tool marks. Constituents of the sandstones are quartz, plagioclase, sanidine, orthoclase, fragments of sedimentary and methamorphic rocks, biotite, muscovite, opaque mineral and glauconite. The sandstones, which are not matured in terms of mineralogy and texture, are mainly cemented by calcite, clay matrix and minor iron oxide and glauconite matrix. The sandstones are named lithic arenite, lithic graywacke, feldspathic litharenite and litharenite.

Scaling of permeabilities and friction factors of homogeneously expanding gas-solids fluidized beds: Geldart’s A powders and magnetically stabilized beds

Directory of Open Access Journals (Sweden)

Hristov Jordan Y.

2006-01-01

Full Text Available The concept of a variable friction factor of fluid-driven de form able powder beds undergoing fluidization is discussed. The special problem discussed addresses the friction factor and bed permeability relationships of Geldart’s A powders and magnetically stabilized beds in axial fields. Governing equations and scaling relation ships are developed through three approaches (1 Minimization of the pressure drop with respect to the fluid velocity employing the Darcy-Forchheimer equation together with the Richardson-Zaki scaling law, (2 Minimization of the pres sure drop across an equivalent-channel replacing the actual packed beds by a straight pipe with bed-equivalent obstacle of a simple geometry, and (3 Entropy minimization method applied in cases of the Darcy-Forchheimer equation and the equivalent-channel model. Bed-to-surface heat transfer coefficients are commented in the context of the porosity/length scale relationships developed. Both the pressure drop curves developments and phase diagram de signs are illustrated by applications of the intersection of asymptotes technique to beds exhibiting certain degree of cohesion.

Influence of loading and unloading velocity of confining pressure on strength and permeability characteristics of crystalline sandstone

Science.gov (United States)

Zhang, Dong-ming; Yang, Yu-shun; Chu, Ya-pei; Zhang, Xiang; Xue, Yan-guang

2018-06-01

The triaxial compression test of crystalline sandstone under different loading and unloading velocity of confining pressure is carried out by using the self-made "THM coupled with servo-controlled seepage apparatus for containing-gas coal", analyzed the strength, deformation and permeability characteristics of the sample, the results show that: with the increase of confining pressures loading-unloading velocity, Mohr's stress circle center of the specimen shift to the right, and the ultimate intensity, peak strain and residual stress of the specimens increase gradually. With the decrease of unloading velocity of confining pressure, the axial strain, the radial strain and the volumetric strain of the sample decrease first and then increases, but the radial strain decreases more greatly. The loading and unloading of confining pressure has greater influence on axial strain of specimens. The deformation modulus decreases rapidly with the increase of axial strain and the Poisson's ratio decreases gradually at the initial stage of loading. When the confining pressure is loaded, the deformation modulus decrease gradually, and the Poisson's ratio increases gradually. When the confining pressure is unloaded, the deformation modulus increase gradually, and the Poisson's ratio decreases gradually. When the specimen reaches the ultimate intensity, the deformation modulus decreases rapidly, while the Poisson's ratio increases rapidly. The fitting curve of the confining pressure and the deformation modulus and the Poisson's ratio in accordance with the distribution of quadratic polynomial function in the loading-unloading confining pressure. There is a corresponding relationship between the evolution of rock permeability and damage deformation during the process of loading and unloading. In the late stage of yielding, the permeability increases slowly, and the permeability increases sharply after the rock sample is destroyed. Fitting the permeability and confining pressure

Permeability prediction in chalks

DEFF Research Database (Denmark)

Alam, Mohammad Monzurul; Fabricius, Ida Lykke; Prasad, Manika

2011-01-01

The velocity of elastic waves is the primary datum available for acquiring information about subsurface characteristics such as lithology and porosity. Cheap and quick (spatial coverage, ease of measurement) information of permeability can be achieved, if sonic velocity is used for permeability p...... significantly using the effective specific surface as the fluid-flow concept. The FZI unit is appropriate for highly permeable sedimentary rocks such as sandstones and limestones that have small surface areas....

Sandstone-body and shale-body dimensions in a braided fluvial system: Salt wash sandstone member (Morrison formation), Garfield County, Utah

Science.gov (United States)

Robinson, J.W.; McCabea, P.J.

1997-01-01

Excellent three-dimensional exposures of the Upper Jurassic Salt Wash Sandstone Member of the Morrison Formation in the Henry Mountains area of southern Utah allow measurement of the thickness and width of fluvial sandstone and shale bodies from extensive photomosaics. The Salt Wash Sandstone Member is composed of fluvial channel fill, abandoned channel fill, and overbank/flood-plain strata that were deposited on a broad alluvial plain of low-sinuosity, sandy, braided streams flowing northeast. A hierarchy of sandstone and shale bodies in the Salt Wash Sandstone Member includes, in ascending order, trough cross-bedding, fining-upward units/mudstone intraclast conglomerates, singlestory sandstone bodies/basal conglomerate, abandoned channel fill, multistory sandstone bodies, and overbank/flood-plain heterolithic strata. Trough cross-beds have an average width:thickness ratio (W:T) of 8.5:1 in the lower interval of the Salt Wash Sandstone Member and 10.4:1 in the upper interval. Fining-upward units are 0.5-3.0 m thick and 3-11 m wide. Single-story sandstone bodies in the upper interval are wider and thicker than their counterparts in the lower interval, based on average W:T, linear regression analysis, and cumulative relative frequency graphs. Multistory sandstone bodies are composed of two to eight stories, range up to 30 m thick and over 1500 m wide (W:T > 50:1), and are also larger in the upper interval. Heterolithic units between sandstone bodies include abandoned channel fill (W:T = 33:1) and overbank/flood-plain deposits (W:T = 70:1). Understanding W:T ratios from the component parts of an ancient, sandy, braided stream deposit can be applied in several ways to similar strata in other basins; for example, to (1) determine the width of a unit when only the thickness is known, (2) create correlation guidelines and maximum correlation lengths, (3) aid in interpreting the controls on fluvial architecture, and (4) place additional constraints on input variables to

Characterization of a fluvial aquifer at a range of depths and scales: the Triassic St Bees Sandstone Formation, Cumbria, UK

Science.gov (United States)

Medici, Giacomo; West, L. J.; Mountney, N. P.

2018-03-01

Fluvial sedimentary successions represent porous media that host groundwater and geothermal resources. Additionally, they overlie crystalline rocks hosting nuclear waste repositories in rift settings. The permeability characteristics of an arenaceous fluvial succession, the Triassic St Bees Sandstone Formation in England (UK), are described, from core-plug to well-test scale up to 1 km depth. Within such lithified successions, dissolution associated with the circulation of meteoric water results in increased permeability ( K 10-1-100 m/day) to depths of at least 150 m below ground level (BGL) in aquifer systems that are subject to rapid groundwater circulation. Thus, contaminant transport is likely to occur at relatively high rates. In a deeper investigation (> 150 m depth), where the aquifer has not been subjected to rapid groundwater circulation, well-test-scale hydraulic conductivity is lower, decreasing from K 10-2 m/day at 150-400 m BGL to 10-3 m/day down-dip at 1 km BGL, where the pore fluid is hypersaline. Here, pore-scale permeability becomes progressively dominant with increasing lithostatic load. Notably, this work investigates a sandstone aquifer of fluvial origin at investigation depths consistent with highly enthalpy geothermal reservoirs ( 0.7-1.1 km). At such depths, intergranular flow dominates in unfaulted areas with only minor contribution by bedding plane fractures. However, extensional faults represent preferential flow pathways, due to presence of high connective open fractures. Therefore, such faults may (1) drive nuclear waste contaminants towards the highly permeable shallow (< 150 m BGL) zone of the aquifer, and (2) influence fluid recovery in geothermal fields.

Distribution of discontinuous mudstone beds within wave-dominated shallow-marine deposits: Star Point Sandstone and Blackhawk Formation, Eastern Utah, USA

OpenAIRE

Eide, Christian; Buckley, Simon; Howell, John

2017-01-01

Deposits of wave-dominated shorelines are typically considered to act as relatively simple hydrocarbon reservoirs and are commonly modeled as “tanks of sand”. However, important heterogeneities that can act as barriers to fluid flow occur at the parasequence, bedset and bed scales, especially in viscous oil or low permeability oil fields. Heterogeneities at the parasequence and bedset scale have been well-studied, but discontinuous mudstone-beds occurring within the shoreface have received li...

Aspects of the sedimentology of some uranium-bearing sandstones in the Beaufort West area, Cape Province

International Nuclear Information System (INIS)

Cole, D.I.

1980-01-01

The sedimentology of some uranium-bearing sandstones from the Beaufort Group in the Beaufort West area was studied by use of some 116 vertical profiles measured across and adjacent to 14 mineralized deposits. The vertical profiles consist of 91 field sections and 25 borehole logs. The sandstones are usually multistorey and alternate with a mudstone and/or siltstone succession. The vertical profiles basically consist of a succession of facies. Some 19 facies were recognised within the sandstones on the basis of texture and sedimentary structure. The facies transitions within the sandstone sequence were subjected to a one-step Markov chain analysis. The cumulative thickness of uranium mineralization for each sedimentary facies within the sandstone sequence was measured. Some 99 per cent of the total cumulative thickness occurs within the coarser-grained facies (grain sizes in excess of very fine), which suggests that permeability was an important control on the mineralization. The coarser-grained facies, which mostly represent lower point bar or channel bar deposits near the base of each storey, probably acted as suitable aquifers for the transport of uraniferous solutions. Irregularities in the base of each storey may have interrupted the flow of these solutions and allowed sufficient time for precipitation of the uranium. Carbonaceous debris is frequently associated with the mineralized deposits and most likely acted as an indirect reductant for this precipitation. Mineralization decreases upwards in the sandstone sequence and some 40 per cent of the total cumulative thickness is restricted to the initial storey. The horizontally bedded facies contain a high proportion of the total cumulative thickness of mineralization (45 per cent) and this again may be related to a more abundant content of carbonaceous debris

Sediment transport direction in fluviatile Karharbari sandstone, Giridih Basin, Bihar

Energy Technology Data Exchange (ETDEWEB)

Tewari, R C; Casshyap, S M

1978-01-01

The sandstone is pebbly, very coarse grained in the lower part, and coarse to medium grained in the upper part. Shale and coal respectively constitute 9 and 5% of the strata Small and large erosional channels and successive sets of large scale cross-bedding characterize the sandstone. Palaeo- currents reveal that the paleodrainage and sediment transport were dominantly directed from SSW to NNE.

Coastal dune facies, Permian Cutler Formation (White Rim Sandstone), Capitol Reef National Park area, southern Utah

Science.gov (United States)

Kamola, Diane L.; Chan, Marjorie A.

1988-04-01

The Permian Cutler Formation (White Rim Sandstone) in the Capitol Reef National Park area in southern Utah is an excellent example of a coastal dune complex subjected to periodic flooding by marine waters. Wind-ripple, grainfall and grainflow laminae compose the cross-sets deposited by eolian dunes. However, wave-reworked structures such as oscillation ripples, the occurrence of the characteristically marine trace fossils Thalassinoides and Chondrites, and interfingering marine carbonate beds of the Kaibab Formation collectively indicate marine interaction with the eolian environment. Four facies are distinguished: cross-stratified sandstone, burrowed to bioturbated sandstone, brecciated and deformed sandstone, and ripple-laminated sandstone and thin carbonate beds. One unusual aspect of the cross-stratified sandstone facies is the abundance of coarse-grained sand. Coarse-grained sand is atypical in many ancient eolian slipface deposits, but occurs here in large slipface foresets as both grainflow and wind-ripple deposits. No water-laid structures are found in these slipface deposits. Coarse-grained sand was probably transported to the Cutler shoreline by fluvial systems draining the Uncompahgre Uplift to the east, and then concentrated as coarse-grained ripples in interdune areas. Some of these coarse-grained ripples migrated up the stoss side of the dunes and accumulations of coarse-grained sand avalanched down the crest to form grainflow deposits. An extensive amount of soft-sediment deformation is indicated by the presence of convolute bedding and brecciation. These features occur near the zone of interfingering with marine carbonate beds of the Kaibab Formation. The water-saturated and moist conditions required for extensive deformation may have been controlled by the proximity of these sandstones to the shoreline, and fluctuations in the associated groundwater table.

Tertiary lithofacies and paleo-geographic framework and interlayer oxidation zone sandstone uranium deposits in Longjiang-Zhaozhou area

International Nuclear Information System (INIS)

Zhang Zhenqiang

2003-01-01

The main points of views for the experiment are: (1) Yi'an formation is mainly composed of limnetic facies of siltstone and fine sandstone, due to weak surface water, limited sedimentation and simple material source; (2) strengthened surface water and enormous material brought from north and west-north and enlarged sedimentation from north to south, the major deposition during Da'an period are channel facies of conglomerate and river bed facies of sandstone; (3) stronger surface water during Taikang period, led alluvial-flood plain facies brown-yellow conglomerate to develop along western margin of the basin, the channel facies of conglomerate and river bed facies of grey-green sandstone, pelitic siltstone were widely formed southward and eastward; (4) according to the lithofacies criterion for in-situ leachable sandstone uranium ore, Taikang formation is an ideal horizon, river bed facies is suitable for interlayer oxidation type uranium deposit. (author)

Geological principles of exploration for sandstone-hosted uranium deposits

International Nuclear Information System (INIS)

Le Roux, J.P.

1982-10-01

Although the importance of sandstone-hosted uranium deposits has seemingly faded in recent years due to the discovery of large, high -grade deposits elsewhere, a forecasted energy shortage in the near future will probably necessitate a new look at sedimentary basins as a source of uranium. Back-arc basins adjacent to calcalkaline source areas are especially favourable if they are filled with fluvial, post-Devonian sediments. Syn- and post-depositional tectonics play an important role in the sedimentation-mineralisation process and should be investigated. The oxidation-reduction state of the sandstones is a valid prospecting tool. Sedimentological environments govern the permeability and vegetal matter content of sandstones and directly control uranium mineralisation

Trench infiltration for managed aquifer recharge to permeable bedrock

Science.gov (United States)

Heilweil, V.M.; Watt, D.E.

2011-01-01

Managed aquifer recharge to permeable bedrock is increasingly being utilized to enhance resources and maintain sustainable groundwater development practices. One such target is the Navajo Sandstone, an extensive regional aquifer located throughout the Colorado Plateau of the western United States. Spreading-basin and bank-filtration projects along the sandstone outcrop's western edge in southwestern Utah have recently been implemented to meet growth-related water demands. This paper reports on a new cost-effective surface-infiltration technique utilizing trenches for enhancing managed aquifer recharge to permeable bedrock. A 48-day infiltration trench experiment on outcropping Navajo Sandstone was conducted to evaluate this alternative surface-spreading artificial recharge method. Final infiltration rates through the bottom of the trench were about 0.5 m/day. These infiltration rates were an order of magnitude higher than rates from a previous surface-spreading experiment at the same site. The higher rates were likely caused by a combination of factors including the removal of lower permeability soil and surficial caliche deposits, access to open vertical sandstone fractures, a reduction in physical clogging associated with silt and biofilm layers, minimizing viscosity effects by maintaining isothermal conditions, minimizing chemical clogging caused by carbonate mineral precipitation associated with algal photosynthesis, and diminished gas clogging associated with trapped air and biogenic gases. This pilot study illustrates the viability of trench infiltration for enhancing surface spreading of managed aquifer recharge to permeable bedrock. ?? 2010.

Microbial mat structures in profile: The Neoproterozoic Sonia Sandstone, Rajasthan, India

Science.gov (United States)

Samanta, Pradip; Mukhopadhyay, Soumik; Mondal, Anudeb; Sarkar, Subir

2011-01-01

Ubiquitous microorganisms, especially cyanobacteria preferably grow on the sediment surface thereby producing microbial mats. In the absence of grazers and bioturbators, microbial mat is a unique feature of the Proterozoic. Most of the papers so far published described a wide variety of bed surface microbial mat structures with rare illustrations from sections perpendicular to bedding. Nonetheless, bed surface exposures are relatively rare in rock records. This limitation of bed surface exposures in rock records suggest that a study of microbial mats in bed-across sections is needed. The 60 m thick coastal marine interval of the Sonia Sandstone Formation is bounded between two terrestrial intervals, a transgressive lag at the base and an unconformity at the top, and has been chosen for exploration of microbial mat structures in bed-across sections. A wide variety of microbial mat-induced structures in bed-across sections are preserved within the coastal interval of the Sonia Sandstone. Though many of these structures are similar in some aspects with bed surface structures, some of those presented here are new. The palaeogeographic range of these microbial structures extends from supralittoral to neritic. Diagenetic alterations of microbial mats produce pyrite and those zones are suitable for the preservation of microbial remains. SEM and EDAX analyses show fossil preservation of filamentous microbial remains that confirm the presence of microbial mats within the coastal interval of the Sonia Sandstone. Effects of proliferation of microbial mats in the siliciclastic depositional setting are numerous. The mat-cover on sediment surfaces hinders reworking and/or erosion of the sediments thereby increases the net sedimentation rate. Successive deposition and preservation of thick microbial mat layer under reducing environments should have a great potential for hydrocarbon production and preservation and therefore these Proterozoic formations could be a target for

Cathodoluminescence, fluid inclusions and trace element data for the syntaxial quartz cementation in the sandstones of Ora Formation, northern Iraq

DEFF Research Database (Denmark)

Omer, Muhamed Fakhri; Friis, Henrik

2018-01-01

Quartz cements of the quartz arenitic sandstones from the Chalky Nasara and Ora section of the (Devonian-Carboniferous) Ora Formation in northern Iraq have been studied. A combination of Hot-Cathodoluminescence (CL), LA-ICP-MS and fluid inclusions microthermometry revealed three syntaxial quartz......-bedded sandstones than in the6 thickly-bedded sandstones filling most of remaining pore space during mesogenesis. The Q3 was formed during early telogenesis stage fully cementing the sandstones and the fractures were filled by hydrothermal chlorite and sulfides. Significant amount of trace elements Al, Li, Ge...

An experimental study of the response of the Galesville sandstone to simulated CAES conditions

Energy Technology Data Exchange (ETDEWEB)

Erikson, R L; Stottlemyre, J A; Smith, R P

1980-07-01

The objective of this experimental study was to determine how the mineralogical and physical characteristics of host rock formations are affected by environmental conditions anticipated for compressed air energy storage (CAES) in porous, permeable rock. In this study, Galesville sandstone cores were reacted in autoclave pressure vessels supporting one of four environments: dry air; heated, air-water vapor; heated, nitrogen-water vapor mixtures; and heated, compressed, liquid water. The simulated CAES environments were maintained in autoclave pressure vessels by controlling the following independent variables: temperature, pressure, time, oxygen content, carbon dioxide content, nitrogen content, and liquid volume. The dependent variables studied were: apparent porosity, gas permeability, water permeability, and friability. These variables were measured at ambient temperature and pressure before and after each sandstone sample was reacted in one of the CAES environments. The experiments gave the following results: the Galesville sandstone exhibited excellent stability in dry air at all temperatures tested (50/sup 0/ to 300/sup 0/C); and significant physical alterations occurred in sandstone samples exposed to liquid water above 150/sup 0/C. Samples shielded from dripping water exhibited excellent stability to 300/sup 0/C; sandstone may be a suitable storage media for heated, humid air provided elevated temperature zones are relatively free of mobile liquid water; and observed changes in the physical properties of the rock may have been caused, in part, by the lack of confining stress on the sample. The inability to apply confining pressure is a severe limitation of autoclave experiments.

Sedimentological reservoir characteristics of the Paleocene fluvial/lacustrine Yabus Sandstone, Melut Basin, Sudan

Science.gov (United States)

Mahgoub, M. I.; Padmanabhan, E.; Abdullatif, O. M.

2016-11-01

Melut Basin in Sudan is regionally linked to the Mesozoic-Cenozoic Central and Western African Rift System (CWARS). The Paleocene Yabus Formation is the main oil producing reservoir in the basin. It is dominated by channel sandstone and shales deposited in fluvial/lacustrine environment during the third phase of rifting in the basin. Different scales of sedimentological heterogeneities influenced reservoir quality and architecture. The cores and well logs analyses revealed seven lithofacies representing fluvial, deltaic and lacustrine depositional environments. The sandstone is medium to coarse-grained, poorly to moderately-sorted and sub-angular to sub-rounded, arkosic-subarkosic to sublitharenite. On the basin scale, the Yabus Formation showed variation in sandstone bodies, thickness, geometry and architecture. On macro-scale, reservoir quality varies vertically and laterally within Yabus Sandstone where it shows progressive fining upward tendencies with different degrees of connectivity. The lower part of the reservoir showed well-connected and amalgamated sandstone bodies, the middle to the upper parts, however, have moderate to low sandstone bodies' connectivity and amalgamation. On micro-scale, sandstone reservoir quality is directly affected by textures and diagenetic changes such as compaction, cementation, alteration, dissolution and kaolinite clays pore fill and coat all have significantly reduced the reservoir porosity and permeability. The estimated porosity in Yabus Formation ranges from 2 to 20% with an average of 12%; while permeability varies from 200 to 500 mD and up to 1 Darcy. The understanding of different scales of sedimentological reservoir heterogeneities might contribute to better reservoir quality prediction, architecture, consequently enhancing development and productivity.

Performance of Different Acids on Sandstone Formations

Directory of Open Access Journals (Sweden)

M. A. Zaman

2013-12-01

Full Text Available Stimulation of sandstone formations is a challenging task, which involves several chemicals and physical interactions of the acid with the formation. Some of these reactions may result in formation damage. Mud acid has been successfully used to stimulate sandstone reservoirs for a number of years. It is a mixture of hydrofluoric (HF and hydrochloric (HCl acids designed to dissolve clays and siliceous fines accumulated in the near-wellbore region. Matrix acidizing may also be used to increase formation permeability in undamaged wells. The change may be up to 50% to 100% with the mud acid. For any acidizing process, the selection of acid (Formulation and Concentration and the design (Pre-flush, Main Acid, After-flush is very important. Different researchers are using different combinations of acids with different concentrations to get the best results for acidization. Mainly the common practice is combination of Hydrochloric Acid – Hydrofluoric with Concentration (3% HF – 12% HCl. This paper presents the results of a laboratory investigation of Orthophosphoric acid instead of hydrochloric acid in one combination and the second combination is Fluoboric and formic acid and the third one is formic and hydrofluoric acid. The results are compared with the mud acid and the results calculated are porosity, permeability, and FESEM Analysis and Strength tests. All of these new combinations shows that these have the potential to be used as acidizing acids on sandstone formations.

Lattice Boltzmann heat transfer model for permeable voxels

Science.gov (United States)

Pereira, Gerald G.; Wu, Bisheng; Ahmed, Shakil

2017-12-01

We develop a gray-scale lattice Boltzmann (LB) model to study fluid flow combined with heat transfer for flow through porous media where voxels may be partially solid (or void). Heat transfer in rocks may lead to deformation, which in turn can modulate the fluid flow and so has significant contribution to rock permeability. The LB temperature field is compared to a finite difference solution of the continuum partial differential equations for fluid flow in a channel. Excellent quantitative agreement is found for both Poiseuille channel flow and Brinkman flow. The LB model is then applied to sample porous media such as packed beds and also more realistic sandstone rock sample, and both the convective and diffusive regimes are recovered when varying the thermal diffusivity. It is found that while the rock permeability can be comparatively small (order milli-Darcy), the temperature field can show significant variation depending on the thermal convection of the fluid. This LB method has significant advantages over other numerical methods such as finite and boundary element methods in dealing with coupled fluid flow and heat transfer in rocks which have irregular and nonsmooth pore spaces.

Desert and groundwater dynamics of the Jurassic Navajo Sandstone, southeast Utah

Science.gov (United States)

Chan, M. A.; Hasiotis, S. T.; Parrish, J. T.

2017-12-01

The Jurassic Navajo Sandstone of southeastern Utah is a rich archive of a desert complex with an active groundwater system, influenced by climate changes and recharge from the Uncompahgre Uplift of the Ancestral Rocky Mountains. This eastern erg margin was dominated by dune deposits of large (>10 m thick) and small (m-scale) crossbedded sandstone sets. Within these porous deposits, common soft sediment deformation is expressed as contorted and upturned bedding, fluid escape structures, concentrations of clastic pipes with ring faults, and thick intervals of massive sandstone embedded in crossbedded sandstone. Collectively, these deformation features reflect changes and/or overpressure in the groundwater system. Interdune deposits record laterally variable bounding surfaces, resulting from the change in position of and proximity to the water table. Interdune modification by pedogenesis from burrows, roots, and trees suggest stable periods of moisture and water supply, as well as periodic drying expressed as polygonal cracked mud- to sand-cracked layers. Freshwater bedded and platy limestone beds represent lakes of decameter to kilometer extent, common in the upper part of the formation. Some carbonate springs that fed the lakes are preserved as limestone buildups (tufa mounds) with microbial structures. Extradunal deposits of rivers to small ephemeral streams show channelized and lenticular, subhorizontal, cm- to m-scale sandstone bodies with basal scours and rip-up clasts. Proxy records of the active hydrology imply a changing landscape at the Navajo desert's edge, punctuated by periods of significant rainfall, runoff, rivers, lakes, and springs, fed by high water table conditions to sustain periods of flourishing communities of plants, arthropods, reptiles, mammals, and dinosaurs. Strong ground motion perturbations periodically disrupted porous, water-saturated sands with possible surface eruptions, adding to the dynamic activity of the desert regime.

Relative permeabilities of supercritical CO2 and brine in carbon sequestration by a two-phase lattice Boltzmann method

Science.gov (United States)

Xie, Jian.-Fei.; He, S.; Zu, Y. Q.; Lamy-Chappuis, B.; Yardley, B. W. D.

2017-08-01

In this paper, the migration of supercritical carbon dioxide (CO2) in realistic sandstone rocks under conditions of saline aquifers, with applications to the carbon geological storage, has been investigated by a two-phase lattice Boltzmann method (LBM). Firstly the digital images of sandstone rocks were reproduced utilizing the X-ray computed microtomography (micro-CT), and high resolutions (up to 2.5 μm) were applied to the pore-scale LBM simulations. For the sake of numerical stability, the digital images were "cleaned" by closing the dead holes and removing the suspended particles in sandstone rocks. In addition, the effect of chemical reactions occurred in the carbonation process on the permeability was taken into account. For the wetting brine and non-wetting supercritical CO2 flows, they were treated as the immiscible fluids and were driven by pressure gradients in sandstone rocks. Relative permeabilities of brine and supercritical CO2 in sandstone rocks were estimated. Particularly the dynamic saturation was applied to improve the reliability of the calculations of the relative permeabilities. Moreover, the effects of the viscosity ratio of the two immiscible fluids and the resolution of digital images on the relative permeability were systematically investigated.

Fluvial-deltaic sedimentation and stratigraphy of the ferron sandstone

Science.gov (United States)

Anderson, P.B.; Chidsey, T.C.; Ryer, T.A.

1997-01-01

East-central Utah has world-class outcrops of dominantly fluvial-deltaic Turonian to Coniacian aged strata deposited in the Cretaceous foreland basin. The Ferron Sandstone Member of the Mancos Shale records the influences of both tidal and wave energy on fluvial-dominated deltas on the western margin of the Cretaceous western interior seaway. Revisions of the stratigraphy are proposed for the Ferron Sandstone. Facies representing a variety of environments of deposition are well exposed, including delta-front, strandline, marginal marine, and coastal-plain. Some of these facies are described in detail for use in petroleum reservoir characterization and include permeability structure.

Application of base-level cycles to sandstone-type uranium deposit: taking Dongsheng uranium deposits as an example

International Nuclear Information System (INIS)

Yang Renchao; Han Zuozhen; Fan Aiping; Chang Xiangchun

2006-01-01

High-resolution sequence stratigraphy taking base-level cycles as interface of reference was developed rapidly in recent years. Its greatest predominance lies in that it can be applied to multi-controled continental sedimentary basins and can effectively improve accuracy and distinguishability of sequence stratigraphy analysis. Principles of base-level cycles can also be applied to the research and practice of the exploration and exploitation of sandstone-type uranium deposits as they control the spatial distribution, porosity, the permeability and the sealing ability of sandstone and mudstone, and stacking patterns of strata configuration. Taking Dongsheng uranium deposits as an example, the application of base-level cycles to exploration and exploitation of sandstone uranium deposits was analyzed. It is suggested that favorable strata framework of sandstone and mudstone was developed very well in the fluctuation of base-level cycles. Sand bodies were provided with good connectedness, coarse granularity, high debris content, low matrix content and good porosity-permeability becoming the most important uranium hosted strata. (authors)

Comparison of Buffer Effect of Different Acids During Sandstone Acidizing

International Nuclear Information System (INIS)

Shafiq, Mian Umer; Mahmud, Hisham Khaled Ben; Hamid, Mohamed Ali

2015-01-01

The most important concern of sandstone matrix acidizing is to increase the formation permeability by removing the silica particles. To accomplish this, the mud acid (HF: HCl) has been utilized successfully for many years to stimulate the sandstone formations, but still it has many complexities. This paper presents the results of laboratory investigations of different acid combinations (HF: HCl, HF: H 3 PO 4 and HF: HCOOH). Hydrofluoric acid and fluoboric acid are used to dissolve clays and feldspar. Phosphoric and formic acids are added as a buffer to maintain the pH of the solution; also it allows the maximum penetration of acid into the core sample. Different tests have been performed on the core samples before and after the acidizing to do the comparative study on the buffer effect of these acids. The analysis consists of permeability, porosity, color change and pH value tests. There is more increase in permeability and porosity while less change in pH when phosphoric and formic acids were used compared to mud acid. From these results it has been found that the buffer effect of phosphoric acid and formic acid is better than hydrochloric acid. (paper)

Discussion on the differences between epigenetic oxidized and primary red beds

International Nuclear Information System (INIS)

Chen Xiaolin; Fang Xiheng; Sun Ye; Pang Yaqing; Guo Qingyin

2008-01-01

The red oxidation zone may be formed in the process of the interlayer oxidation. If the original gray beds formed in the moist palaeoclimatic condition and became red in oxidation, it is easy to distinguish this red oxidization zone from the original red beds. Gray sandstone sandwiched by red mudstone can be formed partially in the arid-semiarid condition. If this gray sandstone was oxidized to be red in color, almost all the strata would be red in cross section, and then it will be difficult to distinguish these red strata from the original red beds. If they are regarded as original red beds, we maybe lose the favorable opportunity to find uranium deposit. This paper presents a case study of Yaojia Formation, Upper Cretaceous in the southwestern part of Songliao Basin. Although the palaeoelimatic condition was arid-semiarid, the gray sandstones of Yaojia Formation in Qianjiadian Sag and its adjacent areas have obvious characteristics of primary depositional origin, and part of them may be formed by epigenetic reduction. The gray sandstone has formed red interlayer oxidation zone after being oxidized and it is just the red interlayer oxidation zone which controls the uranium mineralization in Qianjiadian uranium deposit. By careful contrast and analysis, identification marks of red epigenetic oxidation beds have be established, which can effectively help the distinguishing of epigenetic oxidized red beds from original red beds and extends prospecting idea. (authors)

Experimental investigation of the strength and failure behavior of layered sandstone under uniaxial compression and Brazilian testing

Science.gov (United States)

Yin, Peng-Fei; Yang, Sheng-Qi

2018-05-01

As a typical inherently anisotropic rock, layered sandstones can differ from each other in several aspects, including grain size, type of material, type of cementation, and degree of compaction. An experimental study is essential to obtain and convictive evidence to characterize the mechanical behavior of such rock. In this paper, the mechanical behavior of a layered sandstone from Xuzhou, China, is investigated under uniaxial compression and Brazilian test conditions. The loading tests are conducted on 7 sets of bedding inclinations, which are defined as the angle between the bedding plane and horizontal direction. The uniaxial compression strength (UCS) and elastic modulus values show an undulatory variation when the bedding inclination increases. The overall trend of the UCS and elastic modulus values with bedding inclination is decreasing. The BTS value decreases with respect to the bedding inclination and the overall trend of it is approximating a linear variation. The 3D digital high-speed camera images reveal that the failure and fracture of a specimen are related to the surface deformation. Layered sandstone tested under uniaxial compression does not show a typical failure mode, although shear slip along the bedding plane occurs at high bedding inclinations. Strain gauge readings during the Brazilian tests indicate that the normal stress on the bedding plane transforms from compression to tension as the bedding inclination increases. The stress parallel to the bedding plane in a rock material transforms from tension to compression and agrees well with the fracture patterns; "central fractures" occur at bedding inclinations of 0°-75°, "layer activation" occurs at high bedding inclinations of 75°-90°, and a combination of the two occurs at 75°.

New Acid Combination for a Successful Sandstone Acidizing

Science.gov (United States)

Shafiq, M. U.; Mahmud, H. K. B.; Rezaee, R.

2017-05-01

With the development of new enhanced oil recovery techniques, sandstone acidizing has been introduced and played a pivotal role in the petroleum industry. Different acid combinations have been applied, which react with the formation, dissolve the soluble particles; thus increase the production of hydrocarbons. To solve the problems which occurred using current preflush sandstone acidizing technology (hydrochloric acid); a new acid combination has been developed. Core flooding experiments on sandstone core samples with dimensions 1.5 in. × 3 in. were conducted at a flow rate of 2 cm3/min. A series of hydrochloric-acetic acid mixtures with different ratios were tested under 150°F temperature. The core flooding experiments performed are aimed to dissolve carbonate, sodium, potassium and calcium particles from the core samples. These experiments are followed by few important tests which include, porosity-permeability, pH value, Inductively Coupled Plasma (ICP) analysis and Nuclear Magnetic Resonance (NMR measurements). All the results are compared with the results of conventional hydrochloric acid technology. NMR and porosity analysis concluded that the new acid combination is more effective in creating fresh pore spaces and thus increasing the reservoir permeability. It can be seen from the pore distribution before and after the acidizing. Prior applying acid; the large size of pores appears most frequently in the pore distribution while with the applied acid, it was found that the small pore size is most the predominant of the pore distribution. These results are validated using ICP analysis which shows the effective removal of calcium and other positive ions from the core sample. This study concludes that the combination of acetic-hydrochloric acid can be a potential candidate for the preflush stage of sandstone acidizing at high temperature reservoirs.

Diagenesis, provenance and depositional environments of the Bunter Sandstone Formation

DEFF Research Database (Denmark)

Olivarius, Mette; Weibel, Rikke; Friis, Henrik

The Bunter Sandstone Formation in the northern North German Basin has large geothermal potential with high porosity and permeability (generally >15% and >100 mD, respectively) and with pore fluid temperatures that are adequate for geothermal energy production (c. 55–60˚C). A combined investigation...

Analysis on depositional system and prospect of sandstone-type uranium deposits of Bayanhua formation in Yilemen basin

International Nuclear Information System (INIS)

Sun Zexuan; Li Guoxin; He Fayang; Wei Yunjie

2002-01-01

Yilemen basin is a typical Mesozoic intra-mountain one. The author analyses characteristics of depositional system and the prospect of sandstone-type uranium deposit in the sedimentary cover of the Bayanhua Formation, Lower Cretaceous. Authors suggest that the conglomerate, sandstone-conglomerate and sandstone beds of braided stream and delta are favourable horizons for locating phreatic and interlayer oxidation zone sandstone-type uranium deposits, i.e. the northwestern side of Dalai uplifted zone, the Chagantaigebuqi narrow sag, and the southern area of Baolinbuqi

Diagenesis and reservoir quality of the Lower Cretaceous Quantou Formation tight sandstones in the southern Songliao Basin, China

Science.gov (United States)

Xi, Kelai; Cao, Yingchang; Jahren, Jens; Zhu, Rukai; Bjørlykke, Knut; Haile, Beyene Girma; Zheng, Lijing; Hellevang, Helge

2015-12-01

The Lower Cretaceous Quantou Formation in the southern Songliao Basin is the typical tight oil sandstone in China. For effective exploration, appraisal and production from such a tight oil sandstone, the diagenesis and reservoir quality must be thoroughly studied first. The tight oil sandstone has been examined by a variety of methods, including core and thin section observation, XRD, SEM, CL, fluorescence, electron probing analysis, fluid inclusion and isotope testing and quantitative determination of reservoir properties. The sandstones are mostly lithic arkoses and feldspathic litharenites with fine to medium grain size and moderate to good sorting. The sandstones are dominated by feldspar, quartz, and volcanic rock fragments showing various stages of disintegration. The reservoir properties are quite poor, with low porosity (average 8.54%) and permeability (average 0.493 mD), small pore-throat radius (average 0.206 μm) and high displacement pressure (mostly higher than 1 MPa). The tight sandstone reservoirs have undergone significant diagenetic alterations such as compaction, feldspar dissolution, quartz cementation, carbonate cementation (mainly ferrocalcite and ankerite) and clay mineral alteration. As to the onset time, the oil emplacement was prior to the carbonate cementation but posterior to the quartz cementation and feldspar dissolution. The smectite to illite reaction and pressure solution at stylolites provide a most important silica sources for quartz cementation. Carbonate cements increase towards interbedded mudstones. Mechanical compaction has played a more important role than cementation in destroying the reservoir quality of the K1q4 sandstone reservoirs. Mixed-layer illite/smectite and illite reduced the porosity and permeability significantly, while chlorite preserved the porosity and permeability since it tends to be oil wet so that later carbonate cementation can be inhibited to some extent. It is likely that the oil emplacement occurred

Effects of reduction in porosity and permeability with depth on storage capacity and injectivity in deep saline aquifers: A case study from the Mount Simon Sandstone aquifer

Science.gov (United States)

Medina, C.R.; Rupp, J.A.; Barnes, D.A.

2011-01-01

The Upper Cambrian Mount Simon Sandstone is recognized as a deep saline reservoir that has significant potential for geological sequestration in the Midwestern region of the United States. Porosity and permeability values collected from core analyses in rocks from this formation and its lateral equivalents in Indiana, Kentucky, Michigan, and Ohio indicate a predictable relationship with depth owing to a reduction in the pore structure due to the effects of compaction and/or cementation, primarily as quartz overgrowths. The regional trend of decreasing porosity with depth is described by the equation: ??(d)=16.36??e-0.00039*d, where ?? is the porosity and d is the depth in m. The decrease of porosity with depth generally holds true on a basinwide scale. Bearing in mind local variations in lithologic and petrophysical character within the Mount Simon Sandstone, the source data that were used to predict porosity were utilized to estimate the pore volume available within the reservoir that could potentially serve as storage space for injected CO2. The potential storage capacity estimated for the Mount Simon Sandstone in the study area, using efficiency factors of 1%, 5%, 10%, and 15%, is 23,680, 118,418, 236,832, and 355,242 million metric tons of CO2, respectively. ?? 2010 Elsevier Ltd.

Pore Structure and Limit Pressure of Gas Slippage Effect in Tight Sandstone

Science.gov (United States)

You, Lijun; Xue, Kunlin; Kang, Yili; Liao, Yi

2013-01-01

Gas slip effect is an important mechanism that the gas flow is different from liquid flow in porous media. It is generally considered that the lower the permeability in porous media is, the more severe slip effect of gas flow will be. We design and then carry out experiments with the increase of backpressure at the outlet of the core samples based on the definition of gas slip effect and in view of different levels of permeability of tight sandstone reservoir. This study inspects a limit pressure of the gas slip effect in tight sandstones and analyzes the characteristic parameter of capillary pressure curves. The experimental results indicate that gas slip effect can be eliminated when the backpressure reaches a limit pressure. When the backpressure exceeds the limit pressure, the measured gas permeability is a relatively stable value whose range is less than 3% for a given core sample. It is also found that the limit pressure increases with the decreasing in permeability and has close relation with pore structure of the core samples. The results have an important influence on correlation study on gas flow in porous medium, and are beneficial to reduce the workload of laboratory experiment. PMID:24379747

Diagenetic history of the Surma Group sandstones (Miocene) in the Surma Basin, Bangladesh

Science.gov (United States)

Rahman, M. Julleh Jalalur; McCann, Tom

2012-02-01

This study examines the various diagenetic controls of the Miocene Surma Group sandstones encountered in petroleum exploration wells from the Surma Basin, which is situated in the northeastern part of the Bengal Basin, Bangladesh. The principal diagenetic minerals/cements in the Surma Group sandstones are Fe-carbonates (with Fe-calcite dominating), quartz overgrowths and authigenic clays (predominantly chlorite, illite-smectite and minor kaolin). The isotopic composition of the carbonate cement revealed a narrow range of δ 18O values (-10.3‰ to -12.4‰) and a wide range of δ 13C value (+1.4‰ to -23.1‰). The δ 13C VPDB and δ 18O VPDB values of the carbonate cements reveal that carbon was most likely derived from the thermal maturation of organic matter during burial, as well as from the dissolution of isolated carbonate clasts and precipitated from mixed marine-meteoric pore waters. The relationship between the intergranular volume (IGV) versus cement volume indicates that compaction played a more significant role than cementation in destroying the primary porosity. However, cementation also played a major role in drastically reducing porosity and permeability in sandstones with poikilotopic, pore-filling blocky cements formed in early to intermediate and deep burial areas. In addition to Fe-carbonate cements, various clay minerals including illite-smectite and chlorite occur as pore-filling and pore-lining authigenic phases. Significant secondary porosity has been generated at depths from 2500 m to 4728 m. The best reservoir rocks found at depths of 2500-3300 m are well sorted, relatively coarse grained; more loosely packed and better rounded sandstones having good porosities (20-30%) and high permeabilities (12-6000 mD). These good quality reservoir rocks are, however, not uniformly distributed and can be considered to be compartmentalized as a result of interbedding with sandstone layers of low to moderate porosities, low permeabilities owing to poor

Study on U-Ra equilibrium coefficient of the in-situ leaching sandstone-type uranium deposits: A case study of Qianjiadian uranium deposit

International Nuclear Information System (INIS)

Xia Yuliang; Xiu Qunye; Han Jun; Li Linqiang; Zheng Jiwei

2013-01-01

This paper investigated the U-Ra equilibrium coefficient (K-p) of mineralized sandstone and mudstone, and unmineralized sandstone and mudstone for the in-situ leaching sandstone-type uranium deposits. It is surprised that all of the mineralized sandstone and mudstone are both relatively to be partial to uranium, but all of the unmineralized sandstone and mudstone are both relatively to be partial to radium. Meanwhile the uranium in mineralized mudstone is relatively richer than that in mineralized sandstone, and the radium in unmineralized mudstone is relatively richer than that in unmineralized sandstone. It is suggested that mudstones were permeable at the uranium mineralized phase and the unmineralized mudstone and sandstone could serve as important mineralized uranium source. (authors)

Structural diagenesis in Upper Carboniferous tight gas sandstones. Lessons learned from the Piesberg analog study

Energy Technology Data Exchange (ETDEWEB)

Steindorf, P.; Hoehne, M.; Becker, S.; Hilgers, C. [RWTH Aachen Univ. (Germany). Energy and Mineral Resources Group (EMR); Koehrer, B. [Wintershall Holding GmbH, Barnstorf (Germany)

2013-08-01

Upper Carboniferous tight gas sandstone reservoirs in NW-Germany consist of thick successions of cyclothems. Our focus is the Westphalian D of the Piesberg quarry near Osnabrueck, which exposes cemented, faulted and jointed third-order coarse- to fine-grained sandstone cycles separated by anthracite coal seams. We characterize the rocks and the lateral variation of rock properties such as porosity to better constrain input data for reservoir modelling. Three cycles are exposed, each approximately 50 m thick. Rock types can be clearly distinguished by spectral gamma ray in the quarry. Sandstones are intensely compacted and cemented with quartz and generally characterized by low porosities < 8 % (Hepycnometry on plugs and cuttings). Porosities are secondary and mainly related to detrital carbonate dissolution. Around faults dissolution is higher and the porosities can increase to up to 25%. The normal faults show different throws in the quarry and bands of shale and coal have smeared into the fault at juxtaposed beds, which may result in compartments. They dominantly strike W-E and NNW-SSE, but subordinate NE-SW striking fault patterns are also present. Joints were analyzed in a 50 x 50 m section of the quarry wall using Lidar (Light detection and ranging) laser scanning, which allows the characterization of the lithology and quantitative measurement of bedding and fracture orientation data in inaccessible areas. NNE-SSW and W-E joint sets are accompanied by northeasterly and northwesterly striking sets. Around faults, fault planes and fractures are cemented with quartz veins, showing localized mass transport. Due to the intense cementation, the sandstones can reach uniaxial strengths of more than 100 MPa normal to bedding, and approximately 50 MPa parallel to bedding. Sandstone beds within and close to faults are leached by fluids, and their uniaxial strength is reduced by a factor of more than two. Our high resolution field data enables a better understanding of

Mechanisms of formation damage in matrix-permeability geothermal wells

Energy Technology Data Exchange (ETDEWEB)

Bergosh, J.L.; Wiggins, R.B.; Enniss, D.O.

1982-04-01

Tests were conducted to determine mechanisms of formation damage that can occur in matrix permeability geothermal wells. Two types of cores were used in the testing, actual cores from the East Mesa Well 78-30RD and cores from a fairly uniform generic sandstone formation. Three different types of tests were run. The East Mesa cores were used in the testing of the sensitivity of core to filtrate chemistry. The tests began with the cores exposed to simulated East Mesa brine and then different filtrates were introduced and the effects of the fluid contrast on core permeability were measured. The East Mesa cores were also used in the second series of tests which tested formation sandstone cores were used in the third test series which investigated the effects of different sizes of entrained particles in the fluid. Tests were run with both single-particle sizes and distributions of particle mixes. In addition to the testing, core preparation techniques for simulating fracture permeability were evaluated. Three different fracture formation mechanisms were identified and compared. Measurement techniques for measuring fracture size and permeability were also developed.

Hydrogeologic controls imposed by mechanical stratigraphy in layered rocks of the Chateauguay River Basin, a U.S.-Canada transborder aquifer

Science.gov (United States)

Morin, Roger H.; Godin, Rejean; Nastev, Miroslav; Rouleau, Alain

2007-01-01

[1] The Châteauguay River Basin delineates a transborder watershed with roughly half of its surface area located in northern New York State and half in southern Québec Province, Canada. As part of a multidisciplinary study designed to characterize the hydrogeologic properties of this basin, geophysical logs were obtained in 12 wells strategically located to penetrate the four major sedimentary rock formations that constitute the regional aquifers. The layered rocks were classified according to their elastic properties into three primary units: soft sandstone, hard sandstone, and dolostone. Downhole measurements were analyzed to identify fracture patterns associated with each unit and to evaluate their role in controlling groundwater flow. Fracture networks are composed of orthogonal sets of laterally extensive, subhorizontal bedding plane partings and bed-delimited, subvertical joints with spacings that are consistent with rock mechanics principles and stress models. The vertical distribution of transmissive zones is confined to a few select bedding plane fractures, with soft sandstone having the fewest (one per 70-m depth) and hard sandstone the most (five per 70-m depth). Bed-normal permeability is examined using a probabilistic model that considers the lengths of flow paths winding along joints and bedding plane fractures. Soft sandstone has the smallest bed-normal permeability primarily because of its wide, geomechanically undersaturated joint spacing. Results indicate that the three formations have similar values of bulk transmissivity, within roughly an order of magnitude, but that each rock unit has its own unique system of groundwater flow paths that constitute that transmissivity.

PERMEABILITY REDUCTION PHENOMENA IN PACKED BEDS, FIBER MATS, AND WET WEBS OF PAPER EXPOSED TO FLOW OF LIQUIDS AND SUSPENSIONS: A REVIEW

Directory of Open Access Journals (Sweden)

Martin A. Hubbe

2009-02-01

Full Text Available Filter media, including those prepared from cellulosic materials, often suffer from permeability loss during continued use. To help understand such issues, one can take advantage of an extensive body of related research in such fields as industrial filtration, water purification, enhanced oil recovery, chromatography, paper manufacture, and the leaching of pollutants from impoundments. Though the mechanisms that appear to govern permeability-loss phenomena depend a lot on the details of various applications, the published research has revealed a number of common features. In particular, flow through a porous bed or fiber mat can be markedly reduced by deposition of particles or colloidal matter in positions that either block or partially restrict fluid flow. Progress has been achieved in the development of mechanistic models, as well as the use of such models in numerical simulations to explain various experimental findings. Further research of this type needs to be applied to cellulosic materials, which tend to be much more elongated in comparison to the bed materials and suspended matter considered most often by most researchers active in research related to permeability loss.

Hydrogeochemistry and coal-associated bacterial populations from a methanogenic coal bed

Science.gov (United States)

Barnhart, Elliott P.; Weeks, Edwin P.; Jones, Elizabeth J.P.; Ritter, Daniel J.; McIntosh, Jennifer C.; Clark, Arthur C.; Ruppert, Leslie F.; Cunningham, Alfred B.; Vinson, David S.; Orem, William H.; Fields, Matthew W.

2016-01-01

Biogenic coalbed methane (CBM), a microbially-generated source of natural gas trapped within coal beds, is an important energy resource in many countries. Specific bacterial populations and enzymes involved in coal degradation, the potential rate-limiting step of CBM formation, are relatively unknown. The U.S. Geological Survey (USGS) has established a field site, (Birney test site), in an undeveloped area of the Powder River Basin (PRB), with four wells completed in the Flowers-Goodale coal bed, one in the overlying sandstone formation, and four in overlying and underlying coal beds (Knoblach, Nance, and Terret). The nine wells were positioned to characterize the hydraulic conductivity of the Flowers-Goodale coal bed and were selectively cored to investigate the hydrogeochemistry and microbiology associated with CBM production at the Birney test site. Aquifer-test results indicated the Flowers-Goodale coal bed, in a zone from about 112 to 120 m below land surface at the test site, had very low hydraulic conductivity (0.005 m/d) compared to other PRB coal beds examined. Consistent with microbial methanogenesis, groundwater in the coal bed and overlying sandstone contain dissolved methane (46 mg/L average) with low δ13C values (−67‰ average), high alkalinity values (22 meq/kg average), relatively positive δ13C-DIC values (4‰ average), and no detectable higher chain hydrocarbons, NO3−, or SO42−. Bioassay methane production was greatest at the upper interface of the Flowers-Goodale coal bed near the overlying sandstone. Pyrotag analysis identified Aeribacillus as a dominant in situbacterial community member in the coal near the sandstone and statistical analysis indicated Actinobacteria predominated coal core samples compared to claystone or sandstone cores. These bacteria, which previously have been correlated with hydrocarbon-containing environments such as oil reservoirs, have demonstrated the ability to produce biosurfactants to break down

Experimental Investigation on Hydraulic Properties of Granular Sandstone and Mudstone Mixtures

Directory of Open Access Journals (Sweden)

Dan Ma

2018-01-01

Full Text Available The caved zone during longwall mining has high permeability, resulting in a mass of groundwater storage which causes a threat of groundwater inrush hazard to the safe mining. To investigate the hazard mechanism of granular sandstone and mudstone mixture (SMM in caved zone, this paper presents an experimental study on the effect of sandstone particle (SP and mudstone particle (MP weight ratio on the non-Darcy hydraulic properties evolution. A self-designed granular rock seepage experimental equipment has been applied to conduct the experiments. The variation of particle size distribution was induced by loading and water seepage during the test, which indicated that the particle crushing and erosion properties of mudstone were higher than those of sandstone. Porosity evolution of SMM was strongly influenced by loading (sample height and SP/MP weight ratio. The sample with higher sample height and higher weight ratio of SP achieved higher porosity value. In particular, a non-Darcy equation, for hydraulic properties (permeability κ and non-Darcy coefficient ζ calculation, was sufficient to fit the relation between the hydraulic gradient and seepage velocity. The test results indicated that, due to the absence and narrowing of fracture and void during loading, the permeability κ decreases and the non-Darcy coefficient ζ increases. The variation of the hydraulic properties of the sample within the same particle size and SP/MP weight ratio indicated that groundwater inrush hazard showed a higher probability of occurrence in sandstone strata and crushed zone (e.g., faults. Moreover, isolated fractures and voids were able to achieve the changeover from self-extension to interconnection at the last loading stage, which caused the fluctuation tendency of κ and ζ. Fluctuation ability in mudstone was higher than that in sandstone. The performance of an empirical model was also investigated for the non-Darcy hydraulic properties evolution prediction of

Uranium distribution and sandstone depositional environments: oligocene and upper Cretaceous sediments, Cheyenne basin, Colorado

International Nuclear Information System (INIS)

Nibbelink, K.A.; Ethridge, F.G.

1984-01-01

Wyoming-type roll-front uranium deposits occur in the Upper Cretaceous Laramie and Fox Hills sandstones in the Cheyenne basin of northeastern Colorado. The location, geometry, and trend of specific depositional environments of the Oligocene White River and the Upper Cretaceous Laramie and Fox Hills formations are important factors that control the distribution of uranium in these sandstones. The Fox Hills Sandstone consists of up to 450 ft (140 m) of nearshore marine wave-dominated delta and barrier island-tidal channel sandstones which overlie offshore deposits of the Pierre Shale and which are overlain by delta-plain and fluvial deposits of the Laramie Formation. Uranium, which probably originated from volcanic ash in the White River Formation, was transported by groundwater through the fluvial-channel deposits of the White River into the sandstones of the Laramie and Fox Hills formations where it was precipitated. Two favorable depositional settings for uranium mineralization in the Fox Hills Sandstone are: (1) the landward side of barrier-island deposits where barrier sandstones thin and interfinger with back-barrier organic mudstones, and (2) the intersection of barrier-island and tidal channel sandstones. In both settings, sandstones were probably reduced during early burial by diagenesis of contained and adjacent organic matter. The change in permeability trends between the depositional strike-oriented barrier sandstones and the dip-oriented tidal-channel sandstones provided sites for dispersed groundwater flow and, as demonstrated in similar settings in other depositional systems, sites for uranium mineralization

Environmental Assessment Addressing Gate Complex Construction at Scott Air Force Base, Illinois

Science.gov (United States)

2014-04-01

of low permeability, Pennsylvanian-age shale with thin, discontinuous beds of sandstone and limestone (SAFB 2011c). EA for Gate Complex...deposits is the Pennsylvanian-age layers of shale, siltstone, sandstone , limestone, claystone, and coal, lying approximately 85 feet below ground surface...The Pennsylvanian strata are approximately 265 feet thick. Water-yielding Chesterian Series sandstones lie beneath the Pennsylvanian strata. The

Investigation on the Permeability Evolution of Gypsum Interlayer Under High Temperature and Triaxial Pressure

Science.gov (United States)

Tao, Meng; Yechao, You; Jie, Chen; Yaoqing, Hu

2017-08-01

reduced, which eventually leads to a decrease in permeability. When the inlet gas pressure is between 2 and 6 MPa, the Klinkenberg effect dribbles away, and the gas flow gradually obeys to the Darcy's law. Hence, the permeability increased with the increase in inlet gas pressure. (c) The curve of permeability versus temperature is divided into five stages based on its gradient. In the temperature range of 20-100 °C, the permeability of gypsum decreased slowly when the temperature decreased. From 100 to 200 °C, the permeability of gypsum increased dramatically when the temperature increased. However, a dramatic increase in permeability was observed from 200 to 450 °C. Subsequently, in the temperature range of 450-550 °C, due to closure of pores and fractures, the permeability of the specimens slowly lessened when the temperature increased. From 550 to 650 °C, the permeability of gypsum slightly increased when the temperature increased; (d) the micro-cracks and porosity obtained from the CT images show a high degree of consistency to the permeability evolution; (e) when compared to the permeability evolutions of sandstone, granite, and lignite, gypsum exhibits a stable evolution trend of permeability and has a much greater threshold temperature when its permeability increases sharply. The results of the paper may provide essential and valuable references for the design and construction of high-level radioactive wastes repository in bedded salt rock containing gypsum interlayers.

Use of digital image analysis to estimate fluid permeability of porous materials: Application of two-point correlation functions

International Nuclear Information System (INIS)

Berryman, J.G.; Blair, S.C.

1986-01-01

Scanning electron microscope images of cross sections of several porous specimens have been digitized and analyzed using image processing techniques. The porosity and specific surface area may be estimated directly from measured two-point spatial correlation functions. The measured values of porosity and image specific surface were combined with known values of electrical formation factors to estimate fluid permeability using one version of the Kozeny-Carman empirical relation. For glass bead samples with measured permeability values in the range of a few darcies, our estimates agree well ( +- 10--20%) with the measurements. For samples of Ironton-Galesville sandstone with a permeability in the range of hundreds of millidarcies, our best results agree with the laboratory measurements again within about 20%. For Berea sandstone with still lower permeability (tens of millidarcies), our predictions from the images agree within 10--30%. Best results for the sandstones were obtained by using the porosities obtained at magnifications of about 100 x (since less resolution and better statistics are required) and the image specific surface obtained at magnifications of about 500 x (since greater resolution is required)

Fast Laplace solver approach to pore-scale permeability

Science.gov (United States)

Arns, C. H.; Adler, P. M.

2018-02-01

We introduce a powerful and easily implemented method to calculate the permeability of porous media at the pore scale using an approximation based on the Poiseulle equation to calculate permeability to fluid flow with a Laplace solver. The method consists of calculating the Euclidean distance map of the fluid phase to assign local conductivities and lends itself naturally to the treatment of multiscale problems. We compare with analytical solutions as well as experimental measurements and lattice Boltzmann calculations of permeability for Fontainebleau sandstone. The solver is significantly more stable than the lattice Boltzmann approach, uses less memory, and is significantly faster. Permeabilities are in excellent agreement over a wide range of porosities.

Reservoir characterization of the Mt. Simon Sandstone, Illinois Basin, USA

Science.gov (United States)

Frailey, S.M.; Damico, J.; Leetaru, H.E.

2011-01-01

The integration of open hole well log analyses, core analyses and pressure transient analyses was used for reservoir characterization of the Mt. Simon sandstone. Characterization of the injection interval provides the basis for a geologic model to support the baseline MVA model, specify pressure design requirements of surface equipment, develop completion strategies, estimate injection rates, and project the CO2 plume distribution.The Cambrian-age Mt. Simon Sandstone overlies the Precambrian granite basement of the Illinois Basin. The Mt. Simon is relatively thick formation exceeding 800 meters in some areas of the Illinois Basin. In the deeper part of the basin where sequestration is likely to occur at depths exceeding 1000 m, horizontal core permeability ranges from less than 1 ?? 10-12 cm 2 to greater than 1 ?? 10-8 cm2. Well log and core porosity can be up to 30% in the basal Mt. Simon reservoir. For modeling purposes, reservoir characterization includes absolute horizontal and vertical permeability, effective porosity, net and gross thickness, and depth. For horizontal permeability, log porosity was correlated with core. The core porosity-permeability correlation was improved by using grain size as an indication of pore throat size. After numerous attempts to identify an appropriate log signature, the calculated cementation exponent from Archie's porosity and resistivity relationships was used to identify which porosity-permeability correlation to apply and a permeability log was made. Due to the relatively large thickness of the Mt. Simon, vertical permeability is an important attribute to understand the distribution of CO2 when the injection interval is in the lower part of the unit. Only core analyses and specifically designed pressure transient tests can yield vertical permeability. Many reservoir flow models show that 500-800 m from the injection well most of the CO2 migrates upward depending on the magnitude of the vertical permeability and CO2 injection

Diagenetic controls on porosity variations within an aeolian sandstone reservoir, borehole Kudu 9A-3

International Nuclear Information System (INIS)

Marot, J.E.B.

1990-01-01

Three boreholes, Kudu 9A-1, 9A-2 and 9A-3, were drilled approximately 125 km west of the Orange River mouth to test a gas-bearing structure of Barremian age. The reservoir interval comprises an upper unit of interbedded shallow marine sandstones, limestones and volcaniclastic mass flow deposits, and a lower non-marine unit of interbedded aeolian sandstones, basaltic lavas and volcaniclastic deposits. Despite the overall good poroperm characteristics of the aeolian sandstone and its apparent mineralogical homogeneity, as implied by a gamma ray trace, the core analysis results show an extreme variation in porosity and permeability values. In order to assist in reservoir quality prediction and to assess the regional prospectivity of the sandstone, it was necessary to explain these variations. The resuls of the study indicate that compositionally and texturally the sandstones are extremely homogeneous. It is concluded that the marked variation in the poroperm characteristics of the aeolian sandstones is a result of a relatively complex diagenesis. A fluctuating water table resulted in the formation of a pattern of calcite, anhydrite and quartz cements within an aeolian dune sandstone. 7 refs., 1 fig

Analysis of Fault Permeability Using Mapping and Flow Modeling, Hickory Sandstone Aquifer, Central Texas

Energy Technology Data Exchange (ETDEWEB)

Nieto Camargo, Jorge E., E-mail: jorge.nietocamargo@aramco.com; Jensen, Jerry L., E-mail: jjensen@ucalgary.ca [University of Calgary, Department of Chemical and Petroleum Engineering (Canada)

2012-09-15

Reservoir compartments, typical targets for infill well locations, are commonly created by faults that may reduce permeability. A narrow fault may consist of a complex assemblage of deformation elements that result in spatially variable and anisotropic permeabilities. We report on the permeability structure of a km-scale fault sampled through drilling a faulted siliciclastic aquifer in central Texas. Probe and whole-core permeabilities, serial CAT scans, and textural and structural data from the selected core samples are used to understand permeability structure of fault zones and develop predictive models of fault zone permeability. Using numerical flow simulation, it is possible to predict permeability anisotropy associated with faults and evaluate the effect of individual deformation elements in the overall permeability tensor. We found relationships between the permeability of the host rock and those of the highly deformed (HD) fault-elements according to the fault throw. The lateral continuity and predictable permeability of the HD fault elements enhance capability for estimating the effects of subseismic faulting on fluid flow in low-shale reservoirs.

Quantifying tight-gas sandstone permeability via critical path analysis

Science.gov (United States)

Rock permeability has been actively investigated over the past several decades by the geosciences community. However, its accurate estimation still presents significant technical challenges, especially in spatially complex rocks. In this letter, we apply critical path analysis (CPA) to estimate perm...

Measurements of gas permeability and non-Darcy flow in gas-water-hydrate systems

Energy Technology Data Exchange (ETDEWEB)

Ersland, G.; Husebo, J.; Graue, A.; Kvamme, B. [Bergen Univ., Bergen (Norway). Dept. of Physics and Technology; Baldwin, B. [Green Country Petrophysics LLC, Dewey, OK (United States); Stevens, J.; Howard, J. [ConocoPhillips, OK (United States)

2008-07-01

Storage of carbon dioxide (CO{sub 2}) in natural gas hydrate reservoirs may offer stable long-term storage of a greenhouse gas while benefiting from methane production, without requiring heat. By exposing hydrate to a thermodynamically preferred hydrate former, CO{sub 2}, the hydrate may be maintained macroscopically in the solid state and retain the stability of the formation. However, there is concern over the flow capacity in such reservoirs. This depends on several factors, notably thermodynamic destabilization of hydrate in small pores due to capillary effects; the presence of liquid channels separating the hydrate from the mineral surfaces; and, the connectivity of gas or liquid filled pores and channels. This paper described a technique for measuring gas permeability in gas-water-hydrate systems. It reported on several experiments that measured gas permeability during stages of hydrate growth in sandstone core plugs. Interactions between minerals and surrounding molecules were also discussed. The formation of methane hydrate in porous media was monitored and quantified with magnetic resonance imaging (MRI). MRI images of hydrate growth within the porous rock were provided along with measurements of gas permeability and non-Darcy flow effects at various hydrate saturations. Gas permeability was measured at steady state flow of methane through the hydrate-bearing core sample. Significant gas permeability was recorded for porous sandstone even when hydrates occupied up to 60 per cent of the pore space. It was concluded that MRI imaging can be used effectively to map and quantify hydrate saturation in sandstone core plugs. 27 refs., 2 tabs., 10 figs.

Isopach map of interval between top of the Pictured Cliffs Sandstone and the Huerfanito Bentonite bed of the Lewis Shale, La Plata County, Colorado, and Rio Arriba and San Juan counties, New Mexico

Science.gov (United States)

Sandberg, D.T.

1986-01-01

This thickness map of a Late Cretaceous interval in the northwestern part of the San Juan Basin is part of a study of the relationship between ancient shore 1ines and coal-forming swamps during the filial regression of the Cretaceous epicontinental sea. The top of the thickness interval is the top of the Pictured Cliffs Sands tone. The base of the interval is a thin time marker, the Huerfanito Bentonite Bed of the Lewis Shale. The interval includes all of the Pictured Cliffs Sandstone and the upper part of the Lewis Shale. The northwest boundary of the map area is the outcrop of the Pictured Cliffs Sandstone and the Lewis Shale.

Integrated geomechanical, petrographical and petrophysical study of the sandstones of the Wajid Group, SW Saudi Arabia

Science.gov (United States)

Benaafi, Mohammed; Hariri, Mustafa; Al-Shaibani, Abdulaziz; Abdullatif, Osman; Makkawi, Mohammed

2018-07-01

The Cambro-Permian siliciclastic succession in southwestern Saudi Arabia is represented by the Wajid Group, which consists mainly of fluvial, shallow marine, aeolian, and glacial sandstones. The Wajid Group comprises the Dibsiyah, Sanamah, Qalibah, Khusayyayn, and Juwayl Formations. It is exposed in the Wadi Al-Dawasir area and extends to Najran City. The sandstones of the Wajid Group serve as groundwater aquifers in the Wadi Al-Dawasir and Najran areas and host hydrocarbon (mainly gas) reservoirs in the Rub' Al-Khali Basin. This study aims to characterize the geomechanical properties (rock strength and Young's modulus) of the sandstones of the Wajid Group using field and experimental techniques. A further objective is to investigate the relationships between the geomechanical properties and the petrographical and petrophysical properties of the studied sandstones. The geomechanical properties of the studied sandstones vary from glacial to non-glacial sandstones, as the glacial sandstones display high values of the geomechanical properties with high variability indices. Four geological factors including grain size, cement content, porosity and permeability were observed as the main controls on the geomechanical behaviour of the studied sandstones except for the Khusayyayn sandstone, where the mineral composition was also important. Significant correlations were observed between the petrographical and petrophysical properties and the geomechanical properties of the glacial sandstones. Predictive models of the geomechanical properties (RN, UCS, and E) were generated using regression analysis to account for the glacial sandstones.

Petrographic characterization to build an accurate rock model using micro-CT: Case study on low-permeable to tight turbidite sandstone from Eocene Shahejie Formation.

Science.gov (United States)

Munawar, Muhammad Jawad; Lin, Chengyan; Cnudde, Veerle; Bultreys, Tom; Dong, Chunmei; Zhang, Xianguo; De Boever, Wesley; Zahid, Muhammad Aleem; Wu, Yuqi

2018-03-26

Pore scale flow simulations heavily depend on petrographic characterizing and modeling of reservoir rocks. Mineral phase segmentation and pore network modeling are crucial stages in micro-CT based rock modeling. The success of the pore network model (PNM) to predict petrophysical properties relies on image segmentation, image resolution and most importantly nature of rock (homogenous, complex or microporous). The pore network modeling has experienced extensive research and development during last decade, however the application of these models to a variety of naturally heterogenous reservoir rock is still a challenge. In this paper, four samples from a low permeable to tight sandstone reservoir were used to characterize their petrographic and petrophysical properties using high-resolution micro-CT imaging. The phase segmentation analysis from micro-CT images shows that 5-6% microporous regions are present in kaolinite rich sandstone (E3 and E4), while 1.7-1.8% are present in illite rich sandstone (E1 and E2). The pore system percolates without micropores in E1 and E2 while it does not percolate without micropores in E3 and E4. In E1 and E2, total MICP porosity is equal to the volume percent of macrospores determined from micro-CT images, which indicate that the macropores are well connected and microspores do not play any role in non-wetting fluid (mercury) displacement process. Whereas in E3 and E4 sandstones, the volume percent of micropores is far less (almost 50%) than the total MICP porosity which means that almost half of the pore space was not detected by the micro-CT scan. PNM behaved well in E1 and E2 where better agreement exists in PNM and MICP measurements. While E3 and E4 exhibit multiscale pore space which cannot be addressed with single scale PNM method, a multiscale approach is needed to characterize such complex rocks. This study provides helpful insights towards the application of existing micro-CT based petrographic characterization methodology

Effect of pore structure on the seepage characteristics of tight sandstone reservoirs: A case study of Upper Jurassic Penglaizhen Fm reservoirs in the western Sichuan Basin

Directory of Open Access Journals (Sweden)

Liqiang Sima

2017-01-01

Full Text Available Tight sandstone reservoirs are characterized by complex pore structures and strong heterogeneity, and their seepage characteristics are much different from those of conventional sandstone reservoirs. In this paper, the tight sandstone reservoirs of Upper Jurassic Penglaizhen Fm in western Sichuan Basin were analyzed in terms of their pore structures by using the data about physical property, mercury injection and nuclear magnetic resonance (NMR tests. Then, the seepage characteristics and the gas–water two-phase migration mechanisms and distribution of tight sandstone reservoirs with different types of pore structures in the process of hydrocarbon accumulation and development were simulated by combining the relative permeability experiment with the visual microscopic displacement model. It is shown that crotch-like viscous fingering occurs in the process of gas front advancing in reservoirs with different pore structures. The better the pore structure is, the lower the irreducible water saturation is; the higher the gas-phase relative permeability of irreducible water is, the more easily the gas reservoir can be developed. At the late stage of development, the residual gas is sealed in reservoirs in the forms of bypass, cutoff and dead end. In various reservoirs, the interference between gas and water is stronger, so gas and water tends to be produced simultaneously. The sealed gas may reduce the production rate of gas wells significantly, and the existence of water phase may reduce the gas permeability greatly; consequently, the water-bearing low-permeability tight sandstone gas reservoirs reveal serious water production, highly-difficult development and low-recovery percentage at the late stage, which have adverse impacts on the effective production and development of gas wells.

Determination of water-lock critical value of low-permeability sandstones based on digital core

Directory of Open Access Journals (Sweden)

Honglin Zhu

2016-05-01

Full Text Available Research and development of water lock inhibiting measures is very crucial in verifying the link mechanism between the internal factors of water lock and its extent of damage. Based on conventional water-lock physics experiments, however, only the consequence of macro water lock damage can be investigated, while the microscopic mechanism cannot be studied. In this paper, 3D digital cores of low-permeability sandstones were prepared by means of high-resolution micro-CT scan, and their equivalent pore network model was built as well. Virtual “imbibition” experiments controlled by capillary force were carried out by using pore-scale flow simulation. Then the link mechanism between the microscopic internal factors (e.g. wettability, water saturation and pore–throat structure parameters and the water-lock damage degree was discussed. It is shown that the damage degree of water lock reduces gradually as the wettability transits from water wet to gas wet. Therefore, the water lock damage can be reduced effectively and gas-well productivity can be improved so long as the capillary environment is changed from strong water wettability to weak gas wettability. The more different the initial water saturation is from the irreducible water saturation, the more serious the water lock damage is. The damage degree of water lock is in a negative correlation with the coordinate number, but a positive correlation with the pore–throat ratio. Based on the existing research results, water lock tends to form in the formations composed of medium-sized throats. It is concluded that there is a critical throat radius, at which the water lock is the most serious.

The Upper Permian sandstones of Mountains Mecsek: form elements of uranium ore mineralization and facies relations Pt. 2

International Nuclear Information System (INIS)

Vincze, Janos; Somogyi, Janos

1984-01-01

The ore mineralization in the Upper Permian sandstones of Mountais Mecsek, Hungary, was brought about at the oxidation-reduction front between the grey and red sandstones; the predominant rock colour here is green. The sandstones of different colour are oxidation-reduction species. The formation is a megacycle containing in its core grey sandstones of reduced state with coalified plant remains and in its mantle oxidized red sandstones. Uranium accumulates mainly in the transitional green facies. Uranium content gets enriched to a commercial concentration only if the difference in potential of neighbouring beds is in the range of 400-480 mV. The relationship between organic matter and uranium content in the individual facies is shown. The principles of oxidation-reduction processes in the formation of boundary facies are discussed. (V.N.)

Simulation of forced convection in non-Newtonian fluid through sandstones

Science.gov (United States)

Gokhale, M. Y.; Fernandes, Ignatius

2017-11-01

Numerical simulation is carried out to study forced convection in non-Newtonian fluids flowing through sandstones. Simulation is carried out using lattice Boltzmann method (LBM) for both shear-thinning and shear-thickening, by varying the power law index from 0.5 to 1.5 in Carreau-Yasuda model. Parameters involved in LBM and Carreau model are identified to achieve numerical convergence. Permeability and porosity are varied in the range of 10-10-10-6 and 0.1-0.7, respectively, to match actual geometrical properties of sandstone. Numerical technology is validated by establishing Darcy's law by plotting the graph between velocity and pressure gradient. Consequently, investigation is carried out to study the influence of material properties of porous media on flow properties such as velocity profiles, temperature profiles, and Nusselt number.

Comparison between traditional laboratory tests, permeability measurements and CT-based fluid flow modelling for cultural heritage applications

Energy Technology Data Exchange (ETDEWEB)

De Boever, Wesley, E-mail: Wesley.deboever@ugent.be [UGCT/PProGRess, Dept. of Geology, Ghent University, Krijgslaan 281, 9000 Ghent (Belgium); Bultreys, Tom; Derluyn, Hannelore [UGCT/PProGRess, Dept. of Geology, Ghent University, Krijgslaan 281, 9000 Ghent (Belgium); Van Hoorebeke, Luc [UGCT/Radiation Physics, Dept. of Physics & Astronomy, Ghent University, Proeftuinstraat 86, 9000 Ghent (Belgium); Cnudde, Veerle [UGCT/PProGRess, Dept. of Geology, Ghent University, Krijgslaan 281, 9000 Ghent (Belgium)

2016-06-01

In this paper, we examine the possibility to use on-site permeability measurements for cultural heritage applications as an alternative for traditional laboratory tests such as determination of the capillary absorption coefficient. These on-site measurements, performed with a portable air permeameter, were correlated with the pore network properties of eight sandstones and one granular limestone that are discussed in this paper. The network properties of the 9 materials tested in this study were obtained from micro-computed tomography (μCT) and compared to measurements and calculations of permeability and the capillary absorption rate of the stones under investigation, in order to find the correlation between pore network characteristics and fluid management characteristics of these sandstones. Results show a good correlation between capillary absorption, permeability and network properties, opening the possibility of using on-site permeability measurements as a standard method in cultural heritage applications. - Highlights: • Measurements of capillary absorption are compared to in-situ permeability. • We obtain pore size distribution and connectivity by using micro-CT. • These properties explain correlation between permeability and capillarity. • Correlation between both methods is good to excellent. • Permeability measurements could be a good alternative to capillarity measurement.

Predicting permeability of low enthalpy geothermal reservoirs: A case study from the Upper Triassic − Lower Jurassic Gassum Formation, Norwegian–Danish Basin

DEFF Research Database (Denmark)

Weibel, Rikke; Olivarius, Mette; Kristensen, Lars

2017-01-01

This paper aims at improving the predictability of permeability in low enthalpy geothermal reser-voirs by investigating the effect of diagenesis on sandstone permeability. Applying the best fittedporosity–permeability trend lines, obtained from conventional core analysis, to log-interpreted poros...

Research on geochronology and uranium source of sandstone-hosted uranium ore-formation in major uranium-productive basins, Northern-China

International Nuclear Information System (INIS)

Xia Yuliang; Liu Hanbin; Lin Jinrong; Fan Guang; Hou Yanxian

2004-12-01

A method is developed for correcting uranium content in uranium ore samples by considering the U-Ra equilibrium coefficient, then a U-Pb isochron is drawn up. By performing the above correction ore-formation ages of sandstone-hosted uranium mineralization which may be more realistic have been obtained. The comparative research on U-Pb isotopic ages of detritic zircon in ore-hosting sandstone and zircon in intermediate-acid igneous rocks in corresponding provenance area indicates that the ore-hosting sandstone is originated from the erosion of intermediate-acid igneous rocks and the latters are the material basis for the formation of the uranium-rich sandstone beds. On the basis of the study on U-Pb isotopic system evolution of the provenance rocks and sandstones from ore-hosting series, it is verified that the uranium sources of the sandstone-hosted uranium deposit are: the intermediate-acid igneous rocks with high content of mobile uranium, and the sandstone bodies pre-concentrated uranium. (authors)

Prediction of calcite Cement Distribution in Shallow Marine Sandstone Reservoirs using Seismic Data

Energy Technology Data Exchange (ETDEWEB)

Bakke, N.E.

1996-12-31

This doctoral thesis investigates how calcite cemented layers can be detected by reflection seismic data and how seismic data combined with other methods can be used to predict lateral variation in calcite cementation in shallow marine sandstone reservoirs. Focus is on the geophysical aspects. Sequence stratigraphy and stochastic modelling aspects are only covered superficially. Possible sources of calcite in shallow marine sandstone are grouped into internal and external sources depending on their location relative to the presently cemented rock. Well data and seismic data from the Troll Field in the Norwegian North Sea have been analysed. Tuning amplitudes from stacks of thin calcite cemented layers are analysed. Tuning effects are constructive or destructive interference of pulses resulting from two or more closely spaced reflectors. The zero-offset tuning amplitude is shown to depend on calcite content in the stack and vertical stack size. The relationship is found by regression analysis based on extensive seismic modelling. The results are used to predict calcite distribution in a synthetic and a real data example. It is found that describing calcite cemented beds in shallow marine sandstone reservoirs is not a deterministic problem. Hence seismic inversion and sequence stratigraphy interpretation of well data have been combined in a probabilistic approach to produce models of calcite cemented barriers constrained by a maximum amount of information. It is concluded that seismic data can provide valuable information on distribution of calcite cemented beds in reservoirs where the background sandstones are relatively homogeneous. 63 refs., 78 figs., 10 tabs.

Alternative marine and fluvial models for the non-fossiliferous quartzitic sandstones of the Early Proterozoic Daspoort Formation, Transvaal Sequence of southern Africa

Science.gov (United States)

Eriksson, P. G.; Schreiber, U. M.; van der Neut, M.; Labuschagne, H.; Van Der Schyff, W.; Potgieter, G.

1993-04-01

This paper discusses some of the problems related to the palaeoenvironmental interpretation of non-fossiliferous, early Precambrian, recrystallised quartzitic sandstones, using the Early Proterozoic Daspoort Formation, Transvaal Sequence of southern Africa as a case study. These cross-bedded and planar stratified rocks have been interpreted previously as shallow marine deposits, based on limited studies of areas with well-exposed, relatively undeformed outcrops. This postulate rests largely on the apparently mature nature of the recrystallised sandstones and their thin bedding. Examination of outcrops throughout the preserved basin, including those which have been deformed and metamorphosed, reveals the presence of subordinate immature sandstones. Lateral facies relationships permit an alternative distal fan-fluvial braidplain model to be proposed. This is compatible with collected palaeocurrent data, thicknes trends and results of thin section petrography.

Architecture and quantitative assessment of channeled clastic deposits, Shihezi sandstone (Lower Permian, Ordos Basin, China

Directory of Open Access Journals (Sweden)

Chengye Jia

2017-02-01

Full Text Available Lower Permian Shihezi sandstone in Ordos Basin is the largest gas reservoir in China. Architecture elements of channel, overbank and floodplain facies of braided channel deposits were identified through an outcrops survey, and their proportion of channel facies have been quantitatively estimated from well logging. Characteristics of architecture elements, such as sand thickness, bounding surfaces and lithofacies were investigated through outcrops and core. Petrology of Shihezi sandstone has also been studied in detail. Analysis on sandstone components shows that monocrystalline quartz with approximately 76% bulk volume, and lithic up to 5%–45% bulk volume, are the two main components. Litharenite and lithic quartz sandstone are the main rock types. Compaction is concluded by former researchers as the control factor of low permeability. Examination through thin section reveals that secondary pores developed well in coarse sand. Inter-granular dissolution is included as the positive effect to increasing porosity, and is concluded as the control factor to the generation of net pay. Scale of coarse grained channel fills and channel bar sandstone bodies are quantitatively estimated. Strike-oriented, dip-oriented, and vertical distribution of channel fills and channel bar sandstone bodies have been investigated. The geometry of sand bodies can be depicted as an elongated lens. Subsurface mapping reveals that channel sandstone bodies distribute widely from both lateral and longitudinal cross section profiles, and are poorly connected.

Optimising inflow performance of a long multi-lateral offshore well in low permeability, gas-bearing sandstone: K14-FB 102 case study

Energy Technology Data Exchange (ETDEWEB)

Hands, N. [Shell Canada Ltd., Calgary, AB (Canada); Francis, P. [Shell International Exploration and Production (Netherlands); Whittle, A.; Rajasingam, D. [NAM B. V. (Netherlands)

1998-12-31

Successful completion of the sub-horizontal dual-lateral well, K14-FB 102, to optimize production capacity and reservoir drainage in an offshore gas play in the Dutch sector of the North Sea is described. The two 5-7/8 inch horizontal production intervals were drilled and completed using a rheologically engineered, minimal solids, non-damaging sodium formate brine- based fluid designed as a drill-in fluid for reservoir intervals. The completion was made possible by the selection of the appropriate reservoir drill-in and completion fluid, appropriate level of contingency planning and a fully integrated team approach and custom-made well solution. Inflow performance has matched the performance of cemented and high-performance wells at a much lower cost. It was found that openhole reservoir completion techniques offer relatively inexpensive `fit-for-purpose` well solutions for low permeability sandstone in this region of the North Sea.3 refs., 6 tabs., 7 figs.

On the origin of calcite-cemented sandstones in the clearwater formation oil-sands, Alberta

Energy Technology Data Exchange (ETDEWEB)

Colquhoun, I.M.

1999-01-01

This thesis examined the formation of calcite-cemented sandstones in the Clearwater Formation within the Cold Lake and southern Primrose areas of the Alberta oil sands. Three stages of diagenesis have been recognized, both in the calcite-cemented sandstones and reservoir sands. Diagenesis of the Clearwater Formation in the Cold Lake and southern Primrose areas ended once the reservoir filled with hydrocarbons, but in the Cold Lake area, diagenesis of water-saturated sands likely continued after hydrocarbon emplacement. The reservoir sands in the formation contain a diverse clay mineral assemblage. In general, 0.7 nm clays dominate the diagenetic clay mineralogy of the Clearwater sands. Reservoir sands that contain large amounts of detrital clays and early diagenetic, grain-coating chlorite/smectite have significantly reduced bitumen-saturation. The presence of detrital and diagenetic smectitic clays complicates the removal of bitumen from the Clearwater formation using cyclic steam stimulation techniques because they swell during steam stimulation and reduce porosity and permeability of reservoir sands. Reservoir sands that contain kaolinite, feldspar and calcite react to form smectitic clays, which swell upon cyclic steam stimulation and further reduce porosity and permeability of reservoir sands. However, in the Cold Lake and Primrose areas, the dominant clay mineral is berthierine, which is associated with high calcite, which help to preserve porosity, permeability and bitumen saturation. The porous nature of bitumen-saturated, calcite-cemented sandstones that are laterally extensive could possibly provide a preferential path for steam to initiate calcite dissolution and produce significant concentrations of dissolved carbon dioxide in injected fluids. It was noted that this may then precipitate as carbonate scale within the reservoir and could cause formation damage or affect production equipment. 207 refs., 9 tabs., 58 figs., 3 appendices.

Elastic Dispersion and Attenuation in Fully Saturated Sandstones: Role of Mineral Content, Porosity, and Pressures

Science.gov (United States)

Pimienta, Lucas; Borgomano, Jan V. M.; Fortin, Jérôme; Guéguen, Yves

2017-12-01

Because measuring the frequency dependence of elastic properties in the laboratory is a technical challenge, not enough experimental data exist to test the existing theories. We report measurements of three fluid-saturated sandstones over a broad frequency band: Wilkenson, Berea, and Bentheim sandstones. Those sandstones samples, chosen for their variable porosities and mineral content, are saturated by fluids of varying viscosities. The samples elastic response (Young's modulus and Poisson's ratio) and hydraulic response (fluid flow out of the sample) are measured as a function of frequency. Large dispersion and attenuation phenomena are observed over the investigated frequency range. For all samples, the variation at lowest frequency relates to a large fluid flow directly measured out of the rock samples. These are the cause (i.e., fluid flow) and consequence (i.e., dispersion/attenuation) of the transition between drained and undrained regimes. Consistently, the characteristic frequency correlates with permeability for each sandstone. Beyond this frequency, a second variation is observed for all samples, but the rocks behave differently. For Berea sandstone, an onset of dispersion/attenuation is expected from both Young's modulus and Poisson's ratio at highest frequency. For Bentheim and Wilkenson sandstones, however, only Young's modulus shows dispersion/attenuation phenomena. For Wilkenson sandstone, the viscoelastic-like dispersion/attenuation response is interpreted as squirt flow. For Bentheim sandstone, the second effect does not fully follow such response, which could be due to a lower accuracy in the measured attenuation or to the occurence of another physical effect in this rock sample.

Effects of Heating Rate on the Dynamic Tensile Mechanical Properties of Coal Sandstone during Thermal Treatment

Directory of Open Access Journals (Sweden)

Ming Li

2017-01-01

Full Text Available The effects of coal layered combustion and the heat injection rate on adjacent rock were examined in the process of underground coal gasification and coal-bed methane mining. Dynamic Brazilian disk tests were conducted on coal sandstone at 800°C and slow cooling from different heating rates by means of a Split Hopkinson Pressure Bar (SHPB test system. It was discovered that thermal conditions had significant effects on the physical and mechanical properties of the sandstone including longitudinal wave velocity, density, and dynamic linear tensile strength; as the heating rates increased, the thermal expansion of the sandstone was enhanced and the damage degree increased. Compared with sandstone at ambient temperature, the fracture process of heat-treated sandstone was more complicated. After thermal treatment, the specimen had a large crack in the center and cracks on both sides caused by loading; the original cracks grew and mineral particle cracks, internal pore geometry, and other defects gradually appeared. With increasing heating rates, the microscopic fracture mode transformed from ductile fracture to subbrittle fracture. It was concluded that changes in the macroscopic mechanical properties of the sandstone were result from changes in the composition and microstructure.

Petrographic study of core plugs from lower goru sandstones

International Nuclear Information System (INIS)

Memon, M.K.; Tunio, A.; Leghari, A.

2008-01-01

Petrographic rock type description is a fundamental component in the reservoir description processes and typically included measurement to identify sediment source, texture, composition and mineralogy. Petroleum workers have long used the Petrographic microscope as an in put device to aid in the study of pore systems. Standard Petrographic thin sections are typically 30 micrometers thick and are usually illuminated by transmitted light. Experienced examiners have trained themselves to see information such as pore size, mineralogy, compaction, etc by disregarding artifacts produced by passing light through a section. This method is adequate for qualitative interpretation of data from thin sections. Rocks in thin section under a microscope display great complexity in pore sizes and shapes. Petrographic study provides measurement on rock texture. Texture deals with the size, shape and arrangement of the component minerals of a rock. It is essentially the micro geometry of the rock. Permeability of collected core plugs of lower Goru sandstones was measured. From this Petrographic study we have identified as the sandstone of Lower Goru constitute almost entirely of quartz. The grains range in size from very fine to medium, moderately well sorted to well sorted and rounded to sub rounded in shape. Particularly attention was paid to mineral content present in Lower Goru Sandstone. The mineral composition from these core plugs of Lower Goru Sandstone as identified contain about 70-80% Quartz with traces of feldspar, muscovite, biotite, Epidote and hornblende. Calcite was present as cementing material and it was about 15 -30% of the total rock. (author)

Compact rock material gas permeability properties

Energy Technology Data Exchange (ETDEWEB)

Wang, Huanling, E-mail: whl_hm@163.com [Key Laboratory of Coastal Disaster and Defence, Ministry of Education, Hohai University, Nanjing 210098 (China); LML, University of Lille, Cite Scientifique, 59655 Villeneuve d’Ascq (France); Xu, Weiya; Zuo, Jing [Institutes of Geotechnical Engineering, Hohai University, Nanjing 210098 (China)

2014-09-15

Natural compact rocks, such as sandstone, granite, and rock salt, are the main materials and geological environment for storing underground oil, gas, CO{sub 2,} shale gas, and radioactive waste because they have extremely low permeabilities and high mechanical strengths. Using the inert gas argon as the fluid medium, the stress-dependent permeability and porosity of monzonitic granite and granite gneiss from an underground oil storage depot were measured using a permeability and porosity measurement system. Based on the test results, models for describing the relationships among the permeability, porosity, and confining pressure of rock specimens were analyzed and are discussed. A power law is suggested to describe the relationship between the stress-dependent porosity and permeability; for the monzonitic granite and granite gneiss (for monzonitic granite (A-2), the initial porosity is approximately 4.05%, and the permeability is approximately 10{sup −19} m{sup 2}; for the granite gneiss (B-2), the initial porosity is approximately 7.09%, the permeability is approximately 10{sup −17} m{sup 2}; and the porosity-sensitivity exponents that link porosity and permeability are 0.98 and 3.11, respectively). Compared with moderate-porosity and high-porosity rocks, for which φ > 15%, low-porosity rock permeability has a relatively lower sensitivity to stress, but the porosity is more sensitive to stress, and different types of rocks show similar trends. From the test results, it can be inferred that the test rock specimens’ permeability evolution is related to the relative particle movements and microcrack closure.

Recent exploration progresses on sandstone-hosted uranium deposits in north-western China

International Nuclear Information System (INIS)

Li, Z.

2014-01-01

The metallogenic target selection using multiple exploration techniques and drilling program for sandstone-hosted uranium deposits have been intensively carried out for recent years, and big progresses on new discoveries of uranium reserve/resource have been made in the Mesozoic sedimentary basins such as in Yili, Ordos etc. in North-western China The Yili basin is a depression one within the Tianshan Mountain belt in the western part of China. Its basement is composed of Proterozoic-Paleozoic metamorphic and sedimentary rocks, and covers of Mesozoic sediments. The early-middle Jurassic Shuixigou Group is major uranium-productive beds which are composed of three Formations such as Badaowan, Sangonghe, Xisanyao and eight sedimentary cycles. Uranium deposits are found in the south margin of the Basin and controlled by the redox zone. The combined exploration techniques of detailed sedimentary facies study, Rn-survey, high-precision magnetic and soil geochemical and seismic surveys have been successfully used to have locate the potential targets and mineralization zones. The enlargement of uranium reserve/resources in the known deposits and new resources in the selected new targets and cycles have been achieved through further drilling programs. The Ordos basin is a large Meso-Cenozoic basin developed in North China Platform, with its size of approximately 250,000 km"2 and is well known as an important “energy resources basin” because of abundance of coal, oil and gas deposits. The Dongsheng sandstone type uranium deposit is a large one discovered in recent years in northeastern Ordos basin. It is a special kind of sandstone type uranium deposit, different from other ordinary sandstone type deposits because of its unique signatures. It is generally controlled by a transitional zone between greenish and grayish sandstones, both of those two kinds of sandstones now indicate reduced geochemical environments. The greenish color of the paleooxidized sandstones mainly

An Effective Acid Combination for Enhanced Properties and Corrosion Control of Acidizing Sandstone Formation

International Nuclear Information System (INIS)

Shafiq, Mian Umer; Mahmud, Hisham Khaled Ben

2016-01-01

To fulfill the demand of the world energy, more technologies to enhance the recovery of oil production are being developed. Sandstone acidizing has been introduced and it acts as one of the important means to increase oil and gas production. Sandstone acidizing operation generally uses acids, which create or enlarge the flow channels of formation around the wellbore. In sandstone matrix acidizing, acids are injected into the formation at a pressure below the formation fracturing pressure, in which the injected acids react with mineral particles that may restrict the flow of hydrocarbons. Most common combination is Hydrofluoric Acid - Hydrochloric with concentration (3% HF - 12% HCl) known as mud acid. But there are some problems associated with the use of mud acid i.e., corrosion, precipitation. In this paper several new combinations of acids were experimentally screened to identify the most effective combination. The combinations used consist of fluoboric, phosphoric, formic and hydrofluoric acids. Cores were allowed to react with these combinations and results are compared with the mud acid. The parameters, which are analyzed, are Improved Permeability Ratio, strength and mineralogy. The analysis showed that the new acid combination has the potential to be used in sandstone acidizing. (paper)

The sedimentology of uranium-bearing sandstones on the farm Ryst Kuil 351 Beaufort West area

International Nuclear Information System (INIS)

Cole, D.I.

1979-06-01

A study of the sedimentology of some uranium-bearing sandstones on the farm Ryst Kuil 351 was made in order to assess possible relationships between the mineralisation and the sedimentary facies and/or the palaeo-environment. Use was made of 6 vertical profiles, derived from horizontal traverses. 12 sedimentary facies were recognised according to grain-size and sedimentary structure. The transitions between these facies, as derived from the vertical profiles, were subjected to Markov analysis. Only 3 Markov-dependent transitions were derived, but several facies transitions and associations occurred with greater than random frequency. These, together with the vertical profiles, were used to interpret the palaeo-environmental succession. This succession is fluvial meandering and two sub-environments - channel and flood plain - were delineated according to the prevalence of sandstone or mudstone facies. The uranium-bearing sandstones occur in the lower part of a thick (29 - 46m) multistorey point bar sequence within the channel sub-environment. The mineralisation is associated with koffieklip and is restricted to two sedimentary facies - massive very fine-to-finegrained sandstone and horizontally bedded, very fine- to fine-grained sandstone. The mineralisation normally occurs near the bases of the point bars

Reservoir Characterization of Bridgeport and Cypress Sandstones in Lawrence Field Illinois to Improve Petroleum Recovery by Alkaline-Surfactant-Polymer Flood

Energy Technology Data Exchange (ETDEWEB)

Seyler, Beverly; Grube, John; Huff, Bryan; Webb, Nathan; Damico, James; Blakley, Curt; Madhavan, Vineeth; Johanek, Philip; Frailey, Scott

2012-12-21

were used to better understand porosity and permeability trends in the region and to characterize barriers and define flow units. Diagenetic alterations that impact porosity and permeability include development of quartz overgrowths, sutured quartz grains, dissolution of feldspar grains, formation of clay mineral coatings on grains, and calcite cementation. Many of these alterations are controlled by facies. Mapping efforts identified distinct flow units in the northern part of the field showing that the Pennsylvanian Bridgeport consists of a series of thick incised channel fill sequences. The sandstones are about 75-150 feet thick and typically consist of medium grained and poorly sorted fluvial to distributary channel fill deposits at the base. The sandstones become indistinctly bedded distributary channel deposits in the main part of the reservoir before fining upwards and becoming more tidally influenced near their top. These channel deposits have core permeabilities ranging from 20 md to well over 1000 md. The tidally influenced deposits are more compartmentalized compared to the thicker and more continuous basal fluvial deposits. Fine grained sandstones that are laterally equivalent to the thicker channel type deposits have permeabilities rarely reaching above 250 md. Most of the unrecovered oil in Lawrence Field is contained in Pennsylvanian Age Bridgeport sandstones and Mississippian Age Cypress sandstones. These reservoirs are highly complex and compartmentalized. Detailed reservoir characterization including the development of 3-D geologic and geocellular models of target areas in the field were completed to identify areas with the best potential to recover remaining reserves including unswept and by-passed oil. This project consisted of tasks designed to compile, interpret, and analyze the data required to conduct reservoir characterization for the Bridgeport and Cypress sandstones in pilot areas in anticipation of expanded implementation of ASP flooding in

Exploration for sandstone- type uranium mineralisation in the Siwaliks of northwestern Himalaya, India

International Nuclear Information System (INIS)

Swarnkar, B.M.; Kothari, P.K.; Umamaheswar, K.; Srinivasan, S.

2002-01-01

, porosity-permeability barriers and abundance or reductants such as organic carbon, pyrite and anaerobic bacteria. Subsurrace exploration by drilling was confined down to 150m vertical depth due to limited capacity or drilling rigs. Further exploration beyond 150m depth may help in understanding the behavior of uranium mineraIisation associated with grey beds along the redox interface. (author)

Regional diagenesis of sandstone in the Upper Jurassic Morrison Formation, San Juan Basin, New Mexico and Colorado

International Nuclear Information System (INIS)

Hansley, P.L.

1990-01-01

The author reports that early authigenic mineral assemblages and vitroclastic textures are very well preserved in upper sandstones of the Upper Jurassic Morrison Formation. The distributions of the authigenic minerals were controlled, in part, by chemical gradients in a large saline, alkaline lake (Lake T'oo'dichi) that existed in late Morrison time. Sandstones on lake margins were cemented by smectite and silica, whereas sandstones nearer the lake center, in which waters were most saline and alkaline, were cemented by zeolites. Diagenetic alterations in sandstones were promoted by alkaline interstitial waters that emanated from adjacent fine-grained, tuffaceous lake beds. Metastable phases that precipitated first were replaced relatively quickly by more stable, ordered phases in the geochemically favorable environment of the closed basin setting. Elevation of temperatures above the geothermal gradient was proved by the influx of warm, deep-basin waters that locally modified early diagenetic assemblages during burial diagenesis. In organic- (and commonly also uranium ore-) bearing sandstones located primarily in the southern part of the basin, complex diagenetic assemblages resulted from water/rock reactions involving soluble organic complexes

Investigation of Facies Types and Associations of Kuhlan Red Bed Formation in NW Yemen: A New Hypothesis for Origin and Depositional Environment

Directory of Open Access Journals (Sweden)

Mohammed A. Al-Wosabi

2006-06-01

Full Text Available Varieties of thirteen facies types were recognized in the Kuhlan Formation represented by red bed siliciclastic sequences of argillaceous sediments. Examination of the Kuhlan stratigraphic column included sequence relationships, lithology, sedimentary characters, structures and petrography of the dominant rock types. These facies types are grouped in three distinct associations of facies. The lower unit A comprises association of facies (Distal turbidites represented by alternates of turbidity sequences including sandstone, siltstone and thick shale beds. These facies types confirm a regressive depositional environment in deep marine shelf conditions. There are three facies types which are identified as massive sandstone, cross-bedded sandstone and pebbly sandstone facies. The middle unit B association of facies (Proximal turbedites represents glaciomarine sequences displaying high lateral and vertical facies changes of glacioturbidite sediment alternates with diamictites and tillite beds. The sequences are affected by eustatic and eustatism of the glacial advance and retreat. This unit B includes eight types of facies. These are identified as; tillite, massive diamictites, stratified diamictites, laminated siltstone/shale, deformed siltstone/mudstone, graded rhythmic siltstone, massive conglomerate and cross-stratified sandy conglomerate facies. The upper unit C association of facies is represented by shallow marine shelf sequences displaying very thick massive and locally cross-bedded sand bar sandstone overlying the laminated siltstone/shale interbeds. The upward gradual changes in mineralogical composition and color confirms the start of marine transgression and later deposited platform Amran Group. Mineralogical composition of Kuhlan sandstone displays impure dirty rocks consisting of more than 30% of argillaceous matrix, 50% of cristobalite and quartz grains, more than 10% of ferruginous cement and 10% of detrital iron oxide grains, potash

The sedimentology of uranium-bearing sandstones on the Waterval portion of the farm Brandewyns Gat 214, Beaufort West area

International Nuclear Information System (INIS)

Cole, D.I.

1980-08-01

The sedimentology of two uranium-bearing sandstones on the Waterval portion of the farm Brandewyns Gat 214 was studied by means of 36 vertical profiles measured across, through and adjacent to 4 mineralised deposits. The vertical profiles basically consist of a succession of sedimentary facies. A total of 19 facies was recognised within the fluvial sandstone sequence according to the criteria of grain-size and sedimentary structure. Transitions between the facies were subjected to a Markov chain analysis in order to delineate Markov-dependent transitions. Uranium mineralisation occurs mostly within the lower half of the fluvial sandstone sequence and is confined to the coarser-grained sedimentary facies. These facies probably acted as suitable aquifers for the transport of uraniferous solutions and permeability differences between the sandstone and the underlying mudstone and siltstone must have restricted these solutions to the lower half of the channel sandstone. The massive mudstone facies contains 13 per cent of the total cumulative thickness of mineralisation. This mineralisation probably originated from synchronously deposited tuffaceous material. Subsequent migration of uraniferous solutions may have concentrated the uranium

In situ determination of anisotropic permeability of clay

International Nuclear Information System (INIS)

Shao, H.; Soennke, J.; Morel, J.; Krug, S.

2011-01-01

Argillaceous formations are being considered as potential host rocks for repositories of radioactive waste in many countries. For this purpose, the thermal, hydraulic, mechanical, and chemical properties of the clay stone are being widely investigated in the laboratories and in situ. However, clay stone behaves, due to its tectonic evolution of the formation, hydraulically and mechanically transversal isotropic. Argillite bedding or layering structure has been observed in the underground laboratories Mont Terri in the Switzerland and Meuse/Haute-Marne at Bure site in France. Conventional packer systems used for the borehole hydraulic characterisation cannot distinguish the difference between the properties parallel and perpendicular to the bedding. For this purpose, a new 'slot packer' system has been developed by the BGR. This type of new packer system is intensively tested in the BGR laboratory and the Mont Terri Rock Laboratory to judge the feasibility. The anisotropic ratio of the Opalinus clay defined by permeability value parallel to the bedding/permeability value perpendicular to the bedding is evaluated up to eight times to one order of magnitude within the HG-B experiment in the Mont Terri Rock Laboratory. Within the cooperation between BGR and ANDRA, the 'slot packer' will be used for the measurement of anisotropic permeability of the Callovo-Oxfordian formation at the Bure site. (authors)

Ladinian skonca beds of the Idrija Ore Deposit (W Slovenia

Directory of Open Access Journals (Sweden)

Jože Čar

2013-12-01

Full Text Available The richly mineralised Skonca beds (der Lagerschiefer were the most important mining level of the Idrija ore deposit. In addition to epigenetic ores, exceptional quantities of various rich syngenetic cinnabar ores could be found in these layers. »Jeklenka« (steel ore, »opekovka« (brick ore, »jetrenka« (liver ore, coral ore, and some other bedded cinnabar ores contained up to as much as 78 % Hg. These ores were excavated more or less intensively from their discovery in 1508 until the cessation of works in the Idrija Mine in 1977. The Skonca beds can be found in all parts of the Idrija ore deposit in the form of large or small, irregular, lenseshaped bodies or layers. In the section of the ore deposit known as šTalnina’, the Skonca beds are on average only 4 m thick, and from 10 to maximally 25 m in other parts of the ore deposit. The greatest thickness of these beds, i.e. around 40 m, can be found in the area of the Karóli tectonic unit, situated in the deepest part of the former Idrija Middle Triassic tectonic fault trough. The rocks in the Skonca beds are grouped in typical sequences, which represent a key for the reconstruction of sedimentary environments. The sequences are designated with the letters A, B, C and D. Sequence C is further divided into subsequences C1 with a carbonate and C2 with a siliceous structure. The lithological units of sequence A usually represent the lowest part of the Skonca beds, and may be the lateral equivalents of rocks of series B and subsequence C1. Sequence A is comprised of dispersed, gravelly varieties of carbonatic lythic sandstone, limestone and dolomite siltstone, as well as intercalations of gravelly silty micritic limestone and micritic limestone. Sequence B consists of typical transitional rocks between sequences A and C1, among which silty limestone with transitions to calcitic marlstone and claystone can be found. Sequence C is formed of šclassic’ Skonca rock beds. Although the bottom

CO2 Storage Potential of the Eocene Tay Sandstone, Central North Sea, UK

Science.gov (United States)

Gent, Christopher; Williams, John

2017-04-01

Carbon Capture and Storage (CCS) is crucial for low-carbon industry, climate mitigation and a sustainable energy future. The offshore capacity of the UK is substantial and has been estimated at 78 Gt of CO2 in saline aquifers and hydrocarbon fields. The early-mid Eocene Tay Sandstone Member of the Central North Sea (CNS) is a submarine-fan system and potential storage reservoir with a theoretical capacity of 123 Mt of CO2. The Tay Sandstone comprises of 4 sequences, amalgamating into a fan complex 125km long and 40 km at a minimum of 1500 m depth striking NW-SE, hosting several hydrocarbon fields including Gannett A, B, D and Pict. In order to better understand the storage potential and characteristics, the Tay Sandstone over Quadrant 21 has been interpreted using log correlation and 3D seismic. Understanding the internal and external geometry of the sandstone as well as the lateral extent of the unit is essential when considering CO2 vertical and horizontal fluid flow pathways and storage security. 3D seismic mapping of a clear mounded feature has revealed the youngest sequence of the Tay complex; a homogenous sand-rich channel 12 km long, 1.5 km wide and on average 100 m thick. The sandstone has porosity >35%, permeability >5 D and a net to gross of 0.8, giving a total pore volume of 927x106 m3. The remaining three sequences are a series of stacked channels and interbedded mudstones which are more quiescent on the seismic, however, well logs indicate each subsequent sequence reduce in net to gross with age as mud has a greater influence in the early fan system. Nevertheless, the sandstone properties remain relatively consistent and are far more laterally extensive than the youngest sequence. The Tay Sandstone spatially overlaps several other potential storage sites including the older Tertiary sandstones of the Cromarty, Forties and Mey Members and deeper Jurassic reservoirs. This favours the Tay Sandstone to be considered in a secondary or multiple stacked

Perspective and resource evaluation and metallogenic studies on sandstone-type uranium deposit in Qianjiadian depression of Songliao Basin

Energy Technology Data Exchange (ETDEWEB)

Yuliang, Xia; Jinrong, Lin; Ziying, Li; Shengxiang, Li; Hanbin, Liu; Zhiming, Wang; Guang, Fan [Beijing Research Inst. of Uranium Geology, Beijing (China); Jiwei, Zheng; Zhenji, Li; Mingyu, Zhang [Liaohe Oil Field, Panjin (China)

2003-07-01

The geotectonic evolution history of the southeastern part of Songliao Basin has been clearly described and it is pointed out that both of the provenance rocks and evolution features of the studied area are favorable to the formation of U-rich sandstone bodies, development of interlayered oxidation and providing uranium source for mineralization. Yaojia Formation in Qianjiadian depression has been found out to be the favorable target ore bed for looking for sandstone-type uranium deposit. On the basis of analysis of metallogenetic conditions, the perspective target area has been circled and a sandstone-type uranium deposit with a certain amounts of uranium tonnages has been discovered. The achievements and data have been gotten in the following aspects: constitution and features of ore-forming beds and sandstone bodies, uranium existence forms and mineralogical and chemical compositions of the ores, associated elements and their economic values for comprehensive mining. The study of metallogenetic features and mechanism of the uranium deposit suggested that pre-enrichment of uranium during the depositional-diagenetic stage provide a good basis for uranium mineralization, and hereafter interlayered oxidation as well as oil-gas reduction processes played a decisive role to uranium mineralization. U-Pb isotopic studies indicate that the ores have two isochron ages of 53{+-}3 Ma and 7.0{+-}0 Ma, corresponding to the periods of arid and semiarid paleo-climates which are favorable to interlayered oxidation development and uranium mineralization. It is concluded that the Qianjiadian sandstone-type uranium deposit is genetically related to interlayered oxidation and secondary reduction of oil-gas. The metallogenic model of Qianjiadian uranium deposit was set up. (authors)

Perspective and resource evaluation and metallogenic studies on sandstone-type uranium deposit in Qianjiadian depression of Songliao Basin

International Nuclear Information System (INIS)

Xia Yuliang; Lin Jinrong; Li Ziying; Li Shengxiang; Liu Hanbin; Wang Zhiming; Fan Guang; Zheng Jiwei; Li Zhenji; Zhang Mingyu

2003-01-01

The geotectonic evolution history of the southeastern part of Songliao Basin has been clearly described and it is pointed out that both of the provenance rocks and evolution features of the studied area are favorable to the formation of U-rich sandstone bodies, development of interlayered oxidation and providing uranium source for mineralization. Yaojia Formation in Qianjiadian depression has been found out to be the favorable target ore bed for looking for sandstone-type uranium deposit. On the basis of analysis of metallogenetic conditions, the perspective target area has been circled and a sandstone-type uranium deposit with a certain amounts of uranium tonnages has been discovered. The achievements and data have been gotten in the following aspects: constitution and features of ore-forming beds and sandstone bodies, uranium existence forms and mineralogical and chemical compositions of the ores, associated elements and their economic values for comprehensive mining. The study of metallogenetic features and mechanism of the uranium deposit suggested that pre-enrichment of uranium during the depositional-diagenetic stage provide a good basis for uranium mineralization, and hereafter interlayered oxidation as well as oil-gas reduction processes played a decisive role to uranium mineralization. U-Pb isotopic studies indicate that the ores have two isochron ages of 53±3 Ma and 7.0±0 Ma, corresponding to the periods of arid and semiarid paleo-climates which are favorable to interlayered oxidation development and uranium mineralization. It is concluded that the Qianjiadian sandstone-type uranium deposit is genetically related to interlayered oxidation and secondary reduction of oil-gas. The metallogenic model of Qianjiadian uranium deposit was set up. (authors)

Hydrogeology of the Potsdam Sandstone in northern New York

Science.gov (United States)

Williams, John H.; Reynolds, Richard J.; Franzi, David A.; Romanowicz, Edwin A.; Paillet, Frederick L.

2010-01-01

The Potsdam Sandstone of Cambrian age forms a transboundary aquifer that extends across northern New York and into southern Quebec. The Potsdam Sandstone is a gently dipping sequence of arkose, subarkose, and orthoquartzite that unconformably overlies Precambrian metamorphic bedrock. The Potsdam irregularly grades upward over a thickness of 450 m from a heterogeneous feldspathic and argillaceous rock to a homogeneous, quartz-rich and matrix-poor rock. The hydrogeological framework of the Potsdam Sandstone was investigated through an analysis of records from 1,500 wells and geophysical logs from 40 wells, and through compilation of GIS coverages of bedrock and surficial geology, examination of bedrock cores, and construction of hydrogeological sections. The upper several metres of the sandstone typically is weathered and fractured and, where saturated, readily transmits groundwater. Bedding-related fractures in the sandstone commonly form sub-horizontal flow zones of relatively high transmissivity. The vertical distribution of sub-horizontal flow zones is variable; spacings of less than 10 m are common. Transmissivity of individual flow zones may be more than 100 m2/d but typically is less than 10 m2/d. High angle fractures, including joints and faults, locally provide vertical hydraulic connection between flow zones. Hydraulic head gradients in the aquifer commonly are downward; a laterally extensive series of sub-horizontal flow zones serve as drains for the groundwater flow system. Vertical hydraulic head differences between shallow and deep flow zones range from 1 m to more than 20 m. The maximum head differences are in recharge areas upgradient from the area where the Chateauguay and Chazy Rivers, and their tributaries, have cut into till and bedrock. Till overlies the sandstone in much of the study area; its thickness is generally greatest in the western part, where it may exceed 50 m. A discontinuous belt of bedrock pavements stripped of glacial drift extends

Determination of Hydraulic and Transport Parameters of Organic Chemical and Inorganic Anions Solutes for Unfractured Cores of Berea Sandstone Using a Hydraulic Coreholder

Science.gov (United States)

Blanford, W. J.; Neil, L.

2017-12-01

To better evaluate the potential for toxic organic chemicals to migrate upward through the rock strata from hydraulic fracturing zones and into groundwater resources, a series of miscible displacement solute transport studies of cores of Berea Sandstone have been conducted using hydrostatic core holder. These tests involved passing aqueous solutions with natural background level of salts using a high pressure LC pump through 2 in wide by 3 in long unfractured cores held within the holder. Relative solute transport of 100 to 500ml pulses of target solutes including a series of chlorinated solvents and methylated benzenes was measured through in-line UV and fluorescence detectors and manual sampling and analysis with GCMS. The results found these sandstones to result in smooth ideal shaped breakthrough curves. Analysis with 1D transport models (CXTFIT) of the results found strong correlation with chemical parameters (diffusion coefficients, aqueous solubility, and octanol-water partitioning coefficients) showing that these parameter and QSPR relationships can be used to make accurate predictions for such a system. In addition to the results of the studies, lessons learned from this novel use of a coreholder for evaluation of porosity, water-saturated permeability, and solute transport of these sandstones (K = 1.5cm/day) and far less permeable sandstones samples (K = 0.15 cm/yr) from a hydraulic fracturing site in central Pennsylvania will be presented.

Uranium laterite from Ipora/Amorinopolis region- Goias, Brazil

International Nuclear Information System (INIS)

Fernandes, S.M.

1983-01-01

The present study gives an account of the uranium bearing laterite in the district of Amorinopolis, GO. Emphasis is given in the study of its mineralogy and of the mineralization controls. The uranium mineralization is chiefly found within the arkosic sandstones at the base of the Devonian Ponta Grossa Formation. The ore is tabular and concordant with the bedding, the controls being simultaneously litho-stratigraphic and biochemical. Narrow permeable horizons of arkosic sandstone lie between impermeable shale an siltstone layers. Within the permeable horizon fossil remains (probably brachiopods) are replaced by uranium minerals. The oxidized iron minerals may have acted to insulate and preserve the secondary soluble uranium minerals. (author)

Experimental study and theoretical interpretation of saturation effect on ultrasonic velocity in tight sandstones under different pressure conditions

Science.gov (United States)

Li, Dongqing; Wei, Jianxin; Di, Bangrang; Ding, Pinbo; Huang, Shiqi; Shuai, Da

2018-03-01

Understanding the influence of lithology, porosity, permeability, pore structure, fluid content and fluid distribution on the elastic wave properties of porous rocks is of great significance for seismic exploration. However, unlike conventional sandstones, the petrophysical characteristics of tight sandstones are more complex and less understood. To address this problem, we measured ultrasonic velocity in partially saturated tight sandstones under different effective pressures. A new model is proposed, combining the Mavko-Jizba-Gurevich relations and the White model. The proposed model can satisfactorily simulate and explain the saturation dependence and pressure dependence of velocity in tight sandstones. Under low effective pressure, the relationship of P-wave velocity to saturation is pre-dominantly attributed to local (pore scale) fluid flow and inhomogeneous pore-fluid distribution (large scale). At higher effective pressure, local fluid flow gradually decreases, and P-wave velocity gradually shifts from uniform saturation towards patchy saturation. We also find that shear modulus is more sensitive to saturation at low effective pressures. The new model includes wetting ratio, an adjustable parameter that is closely related to the relationship between shear modulus and saturation.

Sandstone-type uranium deposits

International Nuclear Information System (INIS)

Finch, W.I.; Davis, J.F.

1985-01-01

World-class sandstone-type uranium deposits are defined as epigenetic concentrations of uranium minerals occurring as uneven impregnations and minor massive replacements primarily in fluvial, lacustrine, and deltaic sandstone formations. The main purpose of this introductory paper is to define, classify, and introduce to the general geologic setting for sandstone-type uranium deposits

Geological and Petrophysical Characterization of the Ferron Sandstone for 3-D Simulation of a Fluvial-Deltaic Reservoir

Energy Technology Data Exchange (ETDEWEB)

Chidsey, Jr, Thomas C.

2001-10-31

The objective of the Ferron Sandstone project was to develop a comprehensive, interdisciplinary, quantitative characterization f fluvial-deltaic reservoir to allow realistic interwell and reservoir-scale models to be developed for improved oil-field development in similar reservoirs world-wide. Quantitative geological and petrophysical information on the Cretaceous Ferron Sandstone in east-central Utah was collected. Both new and existing data was integrated into a three-dimensional model of spatial variations in porosity, storativity, and tensorial rock permeability at a scale appropriate for inter-well to regional-scale reservoir simulation. Simulation results could improve reservoir management through proper infill and extension drilling strategies, reduction of economic risks, increased recovery from existing oil fields, and more reliable reserve calculations.

Electrical Spectroscopy of Permo-Triassic Sandstone From the United Kingdom

Science.gov (United States)

Scott, J.; Barker, R.

2003-12-01

Electrical spectroscopy measurements in the range of mHz to kHz have been made on the dominantly red Permo-Triassic sandstone from the United Kingdom. Samples have been selected from borehole cores from all of the main outcrop areas of sandstone and represent a wide variety of lithologies. This sandstone is an important aquifer for several major cities including Manchester and Birmingham. The samples have been fully saturated with sodium chloride brines and a synthetic groundwater solution that is higher in calcium and magnesium ions than sodium and which closely matches the cation concentrations of the groundwater at Birmingham. Electrical measurements were made using a four-electrode arrangement of silver-silver chloride electrodes. Most of the electrical spectra show a clear, slightly asymmetric, electrical relaxation phenomenon with relaxation peaks in the range of 0.001 Hz to 20 Hz. These relaxation phenomena can be fitted very well by a generalised Cole-Cole model. The relaxation time from this model is found to correlate closely with the dominant pore-throat size from mercury injection. Normalising the chargeability, Cole-Cole m parameter, by the conductivity gives a polarisation magnitude which correlates well with the pore surface to volume ratio (SPOR) for sandstone samples with an even distribution of surface coating clays. The information obtained from the electrical spectra is very useful. The pore-throat size is important in controlling the permeability and in particular the flow of non-aqueous phase fluids. The pore surface area has links to the sorbtion properties of the rock, which are important in estimating contaminant transport. The electrical spectra also provide a useful fingerprint of individual lithologies which could be used for correlation between boreholes or outcrops.

Differentiating submarine channel-related thin-bedded turbidite facies: Outcrop examples from the Rosario Formation, Mexico

Science.gov (United States)

Hansen, Larissa; Callow, Richard; Kane, Ian; Kneller, Ben

2017-08-01

Thin-bedded turbidites deposited by sediment gravity flows that spill from submarine channels often contain significant volumes of sand in laterally continuous beds. These can make up over 50% of the channel-belt fill volume, and can thus form commercially important hydrocarbon reservoirs. Thin-bedded turbidites can be deposited in environments that include levees and depositional terraces, which are distinguished on the basis of their external morphology and internal architecture. Levees have a distinctive wedge shaped morphology, thinning away from the channel, and confine both channels (internal levees) and channel-belts (external levees). Terraces are flat-lying features that are elevated above the active channel within a broad channel-belt. Despite the ubiquity of terraces and levees in modern submarine channel systems, the recognition of these environments in outcrop and in the subsurface is challenging. In this outcrop study of the Upper Cretaceous Rosario Formation (Baja California, Mexico), lateral transects based on multiple logged sections of thin-bedded turbidites reveal systematic differences in sandstone layer thicknesses, sandstone proportion, palaeocurrents, sedimentary structures and ichnology between channel-belt and external levee thin-bedded turbidites. Depositional terrace deposits have a larger standard deviation in sandstone layer thicknesses than external levees because they are topographically lower, and experience a wider range of turbidity current sizes overspilling from different parts of the channel-belt. The thickness of sandstone layers within external levees decreases away from the channel-belt while those in depositional terraces are less laterally variable. Depositional terrace environments of the channel-belt are characterized by high bioturbation intensities, and contain distinctive trace fossil assemblages, often dominated by ichnofabrics of the echinoid trace fossil Scolicia. These assemblages contrast with the lower

What classic greywacke (litharenite) can reveal about feldspar diagenesis: An example from Permian Rotliegend sandstone in Hessen, Germany

Science.gov (United States)

Molenaar, Nicolaas; Felder, Marita; Bär, Kristian; Götz, Annette E.

2015-08-01

Rotliegend siliciclastic sediments in southern Hessen (Germany) are a good example of dissolution of detrital feldspars, which is a common feature in many sandstones. Dissolution occurred after mechanical compaction of the lithic-rich sandstone, which experienced framework collapse with pores and pore connections filled and obstructed by deformed ductile lithic grains (pseudomatrix) thereby reducing pore space to microporosity., The advanced degree of compaction and reduced porosity caused low permeability and low hydraulic conductivity of the rock mass. This is further reduced by the presence of wackes and shales that occur intercalated with the sandstones. Feldspar dissolution thus took place in low permeable sediments when large-scale flow of meteoric or acidic fluids is ruled out as a cause of feldspar dissolution. Mineral precipitation (illite, kaolinite, and albite) took place within pseudomatrix and detrital matrix as well as in secondary pores created by feldspar dissolution. Feldspar was the source for the authigenesis. The system was thus closed during burial after framework collapse, and diagenetic reactants in the form of detrital components were already present within the system. The original mass was preserved, but redistributed and diagenetic minerals were the local sinks for the dissolved reactants, precipitating within the system. This also suggests that burial diagenesis in general might be more mass conservative than usually assumed. Rotliegend sandstones thus form a case where, despite of the lack of external exchange of mass by fluid flow, major diagenetic processes did take place and significantly modified the original mineralogy and texture. Feldspar diagenesis can take place from other processes than mere large-scale flushing of open systems as often supposed. It implies that the volumes of rock affected by feldspar diagenesis may be much larger than anticipated based upon the common hold believe that feldspar diagenesis is linked to

Laboratory-determined transport properties of Berea sandstone

International Nuclear Information System (INIS)

Daily, W.D.; Lin, W.

1985-01-01

The authors report laboratory measurements of electrical resistivity water permeability k, and compressional wave velocity V/sub p/ for both intact and fractured Berea sandstone samples as functions of temperature from 20 C to 200 C and effective pressure P/sub e/ from 2.5 MPa to 50 MPa. For the intact sample, V/sub p/ increases from 3.52 km/s to 4.16 km/s as P/sub e/ goes from 3 to 50 MPa. With increasing temperature, V/sub p/ decreases at rates of about 3% per 100 C at P/sub e/ of 5 MPa and about 1.5% per 100 C at P/sub e/ of 38 MPa. Data from the fractured sample are qualitatively similar, but velocities are about 10% lower. For both intact and fractured samples, p increases less than 15% as P/sub e/ increases from 2.5 MPa to 50 MPa. Although both samples show a larger decrease in resistivity with increasing temperature, most of this change is attributed to the decrease in resistivity of the pore fluid over that temperature range. For both samples, k decreases with increasing pressure and temperature. The intact sample permeability varies from 23 mD at 3 MPa and 20 C to less than 1 mD at 50 MPa and 150 C. The permeability of the fractured sample varies from 676 mD at 3 MPa and 20 C to less than 1 mD at 40 MPa and 190 C. The effect of the fracture on k vanishes after several pressure cycles and above about 100 C. These laboratory data are used to demonstrate the possibility of using resistivity and velocity measurements to estimate in-situ permeability of a reservoir. 25 references, 10 figures

Low permeability Neogene lithofacies in Northern Croatia as potential unconventional hydrocarbon reservoirs

Science.gov (United States)

Malvić, Tomislav; Sučić, Antonija; Cvetković, Marko; Resanović, Filip; Velić, Josipa

2014-06-01

We present two examples of describing low permeability Neogene clastic lithofacies to outline unconventional hydrocarbon lithofacies. Both examples were selected from the Drava Depression, the largest macrostructure of the Pannonian Basin System located in Croatia. The first example is the Beničanci Field, the largest Croatian hydrocarbon reservoir discovered in Badenian coarse-grained clastics that consists mostly of breccia. The definition of low permeability lithofacies is related to the margins of the existing reservoir, where the reservoir lithology changed into a transitional one, which is mainly depicted by the marlitic sandstones. However, calculation of the POS (probability of success of new hydrocarbons) shows critical geological categories where probabilities are lower than those in the viable reservoir with proven reserves. Potential new hydrocarbon volumes are located in the structural margins, along the oil-water contact, with a POS of 9.375%. These potential reserves in those areas can be classified as probable. A second example was the Cremušina Structure, where a hydrocarbon reservoir was not proven, but where the entire structure has been transferred onto regional migration pathways. The Lower Pontian lithology is described from well logs as fine-grained sandstones with large sections of silty or marly clastics. As a result, the average porosity is low for conventional reservoir classification (10.57%). However, it is still an interesting case for consideration as a potentially unconventional reservoir, such as the "tight" sandstones.

Sedimentary uranium deposit of the Ipora/Amorinopolis region, state of Goias, Brazil

International Nuclear Information System (INIS)

Fernandes, S.M.; Leonardos, O.H.

1984-01-01

The uranium mineralization is chiefly found within arkosic sandstones at the base of the Devonian Ponta Grossa Formation. The ore is tabular and concordant with the bedding, the controls being simultaneously litho-stratigraphical and biochemical. Narrow permeable horizons of arkosic sandstone lie between impermeable shale and siltstone layers. Within the permeable horizon, the fossil remains (probably brachiopods) are replaced by uranium minerals. The oxidized iron minerals may have acted as to insulate and preserve the secondary soluble uranium minerals. The mineral paragenesis is represented by renardite, meta - autunite I, fourmarierite, Koninckite, ranquilite, meta-uranocircite II, barite, apatite, calophane, wavelite, varscite, an unnamed uranium mineral, quartz, calcedony, goethite, lepidocrocite and hematite. (Author) [pt

Geochemical interpretation of the Precambrian basement and overlying Cambrian sandstone on Bornholm, Denmark: Implications for the weathering history

DEFF Research Database (Denmark)

Zhou, Lingli; Friis, Henrik; Yang, Tian

2017-01-01

show a depletion of major elements in the following order: Na N Ca N Mg N Si; Al and Ti are immobile and stay constant; K shows sample dependent enrichment or depletion; Fe is slightly enriched. The Cambrian sandstone overlying the basement in the Borggård borehole, assigned to the Gadeby Member...... but lost most of the plagioclase. The LSF has a comparable weathering history (CIA = 63–73), but the plagioclase is better preserved (PIA = 65–78). The significant variation of weathering rates of plagioclase and K-feldspar in the basement granite and the provenance of sandstone from the Borggård borehole...... are likely due to the different permeability developed within the internal crystal structures, a Ca- rich plagioclase original composition of the plagioclase, and the occurrence of weathering in a very humid climate. K metasomatism occurred in the basement granite and sandstone in both the Borggård and the G...

In situ determination of anisotropic permeability of clay

International Nuclear Information System (INIS)

Shao, H.; Soennke, J.; Morel, J.; Krug, S.

2010-01-01

in clay stone is generally considered to have a depth of approximately 2 metres. Therefore, a 3-m borehole can also be used for both objects. Ail boreholes are drilled by using dry air technique and oriented parallel to the bedding plane, so that the permeability parallel and perpendicular to the bedding plane can be tested only by turning the 'slot'. Hydraulic tests using gas as test medium are carried out immediately after the drilling of the holes. For evaluation of the measured data, the finite element program RockFlow has been used. The packer 'slot' with a width of 1 cm can also be simulated in the numerical model. Most of the measurements show a clear hydraulic anisotropy due to the bedding structure. As summary, following statements can be made: - Hydraulic anisotropy of clay medium can be determined using the developed 'slot packer' system with orientated applications. - The anisotropic ratio of the Opalinus Clay at Mont Terri (permeability parallel to the bedding/permeability perpendicular to the bedding) may be evaluated up to eight times to one order of magnitude. - Fractures in the excavation damaged zone around the underground opening in clay formations can be identified and especially the orientations of the fractures can be determined using the 'slot packer'. - The fracture permeability has a significant importance for the hydraulic characterisation of the near field. A double packer is sufficient to determine the permeability for this purpose. This tool can also be applied in fractured rock (e.g. granite) to determine the fracture orientation. (authors)

Impact of sauropod dinosaurs on lagoonal substrates in the Broome Sandstone (Lower Cretaceous, Western Australia.

Directory of Open Access Journals (Sweden)

Tony Thulborn

Full Text Available Existing knowledge of the tracks left by sauropod dinosaurs (loosely 'brontosaurs' is essentially two-dimensional, derived mainly from footprints exposed on bedding planes, but examples in the Broome Sandstone (Early Cretaceous of Western Australia provide a complementary three-dimensional picture showing the extent to which walking sauropods could deform the ground beneath their feet. The patterns of deformation created by sauropods traversing thinly-stratified lagoonal deposits of the Broome Sandstone are unprecedented in their extent and structural complexity. The stacks of transmitted reliefs (underprints or ghost prints beneath individual footfalls are nested into a hierarchy of deeper and more inclusive basins and troughs which eventually attain the size of minor tectonic features. Ultimately the sauropod track-makers deformed the substrate to such an extent that they remodelled the topography of the landscape they inhabited. Such patterns of substrate deformation are revealed by investigating fragmentary and eroded footprints, not by the conventional search for pristine footprints on intact bedding planes. For that reason it is not known whether similar patterns of substrate deformation might occur at sauropod track-sites elsewhere in the world.

Impact of Sauropod Dinosaurs on Lagoonal Substrates in the Broome Sandstone (Lower Cretaceous), Western Australia

Science.gov (United States)

Thulborn, Tony

2012-01-01

Existing knowledge of the tracks left by sauropod dinosaurs (loosely ‘brontosaurs’) is essentially two-dimensional, derived mainly from footprints exposed on bedding planes, but examples in the Broome Sandstone (Early Cretaceous) of Western Australia provide a complementary three-dimensional picture showing the extent to which walking sauropods could deform the ground beneath their feet. The patterns of deformation created by sauropods traversing thinly-stratified lagoonal deposits of the Broome Sandstone are unprecedented in their extent and structural complexity. The stacks of transmitted reliefs (underprints or ghost prints) beneath individual footfalls are nested into a hierarchy of deeper and more inclusive basins and troughs which eventually attain the size of minor tectonic features. Ultimately the sauropod track-makers deformed the substrate to such an extent that they remodelled the topography of the landscape they inhabited. Such patterns of substrate deformation are revealed by investigating fragmentary and eroded footprints, not by the conventional search for pristine footprints on intact bedding planes. For that reason it is not known whether similar patterns of substrate deformation might occur at sauropod track-sites elsewhere in the world. PMID:22662116

Electrofacies vs. lithofacies sandstone reservoir characterization Campanian sequence, Arshad gas/oil field, Central Sirt Basin, Libya

Science.gov (United States)

Burki, Milad; Darwish, Mohamed

2017-06-01

The present study focuses on the vertically stacked sandstones of the Arshad Sandstone in Arshad gas/oil field, Central Sirt Basin, Libya, and is based on the conventional cores analysis and wireline log interpretation. Six lithofacies types (F1 to F6) were identified based on the lithology, sedimentary structures and biogenic features, and are supported by wireline log calibration. From which four types (F1-F4) represent the main Campanian sandstone reservoirs in the Arshad gas/oil field. Lithofacies F5 is the basal conglomerates at the lower part of the Arshad sandstones. The Paleozoic Gargaf Formation is represented by lithofacies F6 which is the source provenance for the above lithofacies types. Arshad sediments are interpreted to be deposited in shallow marginal and nearshore marine environment influenced by waves and storms representing interactive shelf to fluvio-marine conditions. The main seal rocks are the Campanian Sirte shale deposited in a major flooding events during sea level rise. It is contended that the syn-depositional tectonics controlled the distribution of the reservoir facies in time and space. In addition, the post-depositional changes controlled the reservoir quality and performance. Petrophysical interpretation from the porosity log values were confirmed by the conventional core measurements of the different sandstone lithofacies types. Porosity ranges from 5 to 20% and permeability is between 0 and 20 mD. Petrophysical cut-off summary of the lower part of the clastic dominated sequence (i. e. Arshad Sandstone) calculated from six wells includes net pay sand ranging from 19.5‧ to 202.05‧, average porosity from 7.7 to 15% and water saturation from 19 to 58%.

Influence of Normal and Shear Stress on the Hydraulic Transmissivity of Thin Cracks in a Tight Quartz Sandstone, a Granite, and a Shale

Science.gov (United States)

Rutter, Ernest H.; Mecklenburgh, Julian

2018-02-01

Transmissivity of fluids along fractures in rocks is reduced by increasing normal stress acting across them, demonstrated here through gas flow experiments on Bowland shale, and oil flow experiments on Pennant sandstone and Westerly granite. Additionally, the effect of imposing shear stress at constant normal stress was determined, until frictional sliding started. In all cases, increasing shear stress causes an accelerating reduction of transmissivity by 1 to 3 orders of magnitude as slip initiated, as a result of the formation of wear products that block fluid pathways. Only in the case of granite, and to a lesser extent in the sandstone, was there a minor amount of initial increase of transmissivity prior to the onset of slip. These results cast into doubt the commonly applied presumption that cracks with high resolved shear stresses are the most conductive. In the shale, crack transmissivity is commensurate with matrix permeability, such that shales are expected always to be good seals. For the sandstone and granite, unsheared crack transmissivity was respectively 2 and 2.5 orders of magnitude greater than matrix permeability. For these rocks crack transmissivity can dominate fluid flow in the upper crust, potentially enough to permit maintenance of a hydrostatic fluid pressure gradient in a normal (extensional) faulting regime.

Study of phosphatic nodules as a possible source of uranium mineralization in warcha sandstone of nilawahan group salt range using SSNTD technique

International Nuclear Information System (INIS)

Qureshi, A.A.; Ullah, K.; Ullah, N.; Mohammad, A.

2004-07-01

The strong in the sedimentary depositional characteristics between the Warcha Sandstone of Nilawahan Group in the Salt Range and the uranium bearing sandstones of Siwalik Group in the foot hills of Himalaya and Sulaiman Ranges tempted the geologists to investigate the former group for the occurrence of any uranium deposits in it. Like volcanic ash beds in Siwaliks, phosphatic nodules may be a possible source of uranium mineralization in Warcha Sandstone of Nilawahan Group. Samples of phosphatic nodules occurring in the Sandstone of Nilawahan Group Salt Range were analyzed using Solid State Nuclear Track Detention Technique (SSNTD) for the determination of their uranium concentration. The results obtained are quite encouraging and favour the idea of exploring the area in detail for any possible occurrence of uranium deposit. Uranium concentration in these samples ranges from (434 + - 39) ppm to (964+ -81)ppm with and average concentration of (699 + - 62) ppm. (author)

Sedimentologie and stratigraphic s aspects of conglomeratic sandstones belong to the channel between of the Pirambora and Botucatu formations (mesozoic basin of Parana)district of Sao Paolo Brazil

International Nuclear Information System (INIS)

Caetano Chang, M.

1998-01-01

The interest of present study is concerned to the sedimentogenic characterization of fluvial conglomeratic sandstones that occur close to the top of Piramboia Formation.These deposits are interpreted as braided channel bar facies, deposited on alluvial fans at the border of desertic environment. The sandstones are fine to coarse, with variable percentage of gravel. These are dominantly quart zones and median scale trough cross-bedded. (author)

Dzhezkazgan and associated sandstone copper deposits of the Chu-Sarysu basin, Central Kazakhstan

Science.gov (United States)

Box, Stephen E.; Seltmann, Reimar; Zientek, Michael L.; Syusyura, Boris; Creaser, Robert A.; Dolgopolova, Alla

2012-01-01

Sandstone-hosted copper (sandstone Cu) deposits occur within a 200-km reach of the northern Chu-Sarysu basin of central Kazakhstan (Dzhezkazgan and Zhaman-Aibat deposits, and the Zhilandy group of deposits). The deposits consist of Cu sulfide minerals as intergranular cement and grain replacement in 10 ore-bearing members of sandstone and conglomerate within a 600- to 1,000-m thick Pennsylvanian fluvial red-bed sequence. Copper metal content of the deposits ranges from 22 million metric tons (Mt, Dzehzkazgan) to 0.13Mt (Karashoshak in the Zhilandy group), with average grades of 0.85 to 1.7% Cu and significant values for silver (Ag) and rhenium (Re). Broader zones of iron reduction (bleaching) of sandstones and conglomerates of the red-bed sequence extend over 10 km beyond each of the deposits along E-NE-trending anticlines, which began to form in the Pennsylvanian. The bleached zones and organic residues within them are remnants of ormer petroleum fluid accumulations trapped by these anticlines. Deposit sites along these F1anticlines are localized at and adjacent to the intersections of nearly orthogonal N-NW-trending F2synclines. These structural lows served to guide the flow of dense ore brines across the petroleum-bearing anticlines, resulting in ore sulfide precipitation where the two fluids mixed. The ore brine was sourced either from the overlying Early Permian lacustrine evaporitic basin, whose depocenter occurs between the major deposits, or from underlying Upper Devonian marine evaporites. Sulfur isotopes indicate biologic reduction of sulfate but do not resolve whether the sulfate was contributed from the brine or from the petroleum fluids. New Re-Os age dates of Cu sulfides from the Dzhezkazgan deposit indicate that mineralization took place between 299 to 309 Ma near the Pennsylvanian-Permian age boundary. At the Dzhezkazgan and some Zhilandy deposits, F2fold deformation continued after ore deposition. Copper orebodies in Lower Permian

Characterization of the Lower Cambrian sandstone aquifer in the Swedish Baltic Sea area - assessment regarding its potential suitability for storage of CO2

Science.gov (United States)

Erlström, M.; Sivhed, U.

2012-04-01

In the Baltic region the Cambrian sandstone is considered to have great economic value concerning its aquifer and reservoir properties. Its potential as petroleum reservoir is well known, especially from the Polish, Lithuanian and Russian sectors of the Baltic Sea where oil and gas has been found in anticline traps in the sandstone sequence. Offshore exploration in the Swedish sector has so far not encountered any significant findings of oil and gas. However, the extensive exploration has generated data, which is now being used for assessing the overall properties regarding suitability for storage of CO2. The Swedish primary industry has a great interest in finding potential sites for storage of CO2. A suitable site in the Baltic Sea would be a most favourable alternative in comparison to more remote alternatives such as deep saline aquifers in the North Sea. The Lower Cambrian is in the Swedish sector of the Baltic Sea composed of three main sandstone units varying in thickness between 5 and 50 m occurring within an up to 250 m thick Cambrian sequence dominated by fine-grained terriclastic sediments. The limit of Lower Palaeozoic sequence in the Baltic area is today defined by erosional truncation because of the gently dipping Lower Palaeozoic sequence. To the north and northwest, the limit is found in the Pre-Quaternary, whereas the erosional limit is deeply buried beneath Permian and Mesozoic sediments to the south. Here the Lower Palaeozoic limit is buried to depths reaching more than 2 km. The Cambrian sequence in the distal parts of the Swedish sector occurs at depths of c. 1300 m while it constitutes the bedrock surface in a narrow zone trending from Öland to the north of of Gotland. Sandstone beds constitute 40-60% of the total Cambrian sequence. The main sandstone units have a regional distribution of several thousands of square kilometres. The up to 50 m thick Faludden sandstone member exhibits the best reservoir properties including porosities in the

Formation factor in Bentheimer and Fontainebleau sandstones: Theory compared with pore-scale numerical simulations

Science.gov (United States)

Ghanbarian, Behzad; Berg, Carl F.

2017-09-01

Accurate quantification of formation resistivity factor F (also called formation factor) provides useful insight into connectivity and pore space topology in fully saturated porous media. In particular the formation factor has been extensively used to estimate permeability in reservoir rocks. One of the widely applied models to estimate F is Archie's law (F = ϕ- m in which ϕ is total porosity and m is cementation exponent) that is known to be valid in rocks with negligible clay content, such as clean sandstones. In this study we compare formation factors determined by percolation and effective-medium theories as well as Archie's law with numerical simulations of electrical resistivity on digital rock models. These digital models represent Bentheimer and Fontainebleau sandstones and are derived either by reconstruction or directly from micro-tomographic images. Results show that the universal quadratic power law from percolation theory accurately estimates the calculated formation factor values in network models over the entire range of porosity. However, it crosses over to the linear scaling from the effective-medium approximation at the porosity of 0.75 in grid models. We also show that the effect of critical porosity, disregarded in Archie's law, is nontrivial, and the Archie model inaccurately estimates the formation factor in low-porosity homogeneous sandstones.

Permeability change with dissolution and precipitation reaction induced by highly alkaline plume in packed bed with amorphous silica particles

International Nuclear Information System (INIS)

Komatsu, Kyo; Kadowaki, Junichi; Niibori, Yuichi; Mimura, Hitoshi; Usui, Hideo

2008-01-01

A large amount of cement is used to construct of the geological disposal system. Such a material alters the pH of groundwater to highly alkaline region. The highly alkaline plume contains rich Ca ion compared to the surrounding environment, and the Ca ion reacts with soluble silicic acid. Its product would deposit on the surface of flow-paths in the natural barrier and decrease the permeability. In this study, the influence of Ca ions in highly alkaline plume on flow-paths has been examined by using packed bed column. The column was packed with the amorphous silica particles of 75-150 μm in diameter. The Ca(OH) 2 solution (0.78 mM, 2.58 mM, 4.37 mM, and 8.48 mM, pH: 12.2-12.4) was continuously injected into the column at a constant flow rate (5 ml/min, and 2 ml/min), and the change of permeability was monitored. At the same time, the concentrations of [Ca] total and [Si] in the eluted solution were measured by the inductively coupled plasma atomic emission spectrometry (ICP-AES). The Ca(OH) 2 solutions were prepared with CO 2 -free pure water, and filtrated through 0.45 μm filter. The permeability was normalized by the initial permeability value. In the experiment results, the permeability dramatically changed with increasing Ca concentration, because Ca ions and H 4 SiO 4 (due to the dissolution of SiO 2 ) produce C-S-H gel between the packed particles in the column. The SEM images and XRD analyses showed that the surface of SiO 2 particles was covered with the C-S-H gel precipitation. On the other hand, when the Ca concentration was relatively low, the permeability did not show remarkable change. For the cross section of SiO 2 particles, EPMA analysis suggested the consumption of Ca in the inner pore of the SiO 2 particles. However, the time-change in the concentrations of Si and Ca was not always simple. Such time-change strongly depended not only on pH or Ca concentration, but also on the flow rates. This suggested that mass transport controls the chemical

Genesis of sandstone-type uranium deposits in the Sierra Pintada district, Mendoza, Argentina: a Moessbauer study

International Nuclear Information System (INIS)

Labenski, F.; Saragovi-Badler, C.

1982-01-01

The genesis of sandstone-type uranium deposits in the Cochico Group (Permo-Triassic) of the Sierra Pintada district, San Rafael, Mendoza, has been studied. This is the most important uranium district in Argentina. Uranium sources, uranium transport and precipitation are discussed. Uraninite and brannerite, the main uranium minerals, occur within the matrix of sandstone. Several phenomena can be deduced regarding the depositional environment. Where oxygen was available, precipitation of hydrated ferric oxides occurred; γFe 2 O 3 .nH 2 O varieties (identified by Moessbauer spectroscopy) precipitated in the upper levels of the aquifer, where CO 2 partial pressure was lower, giving reddish or reddish-brown beds. The CO 2 partial pressure also determines the distribution of biogenic agents such as bacteria. Bacteria thus find a more favourable environment for their development and action in upper levels of an aquifer. In the corresponding horizons local reduction occurred where UO 2 precipitated; therefore the highest uranium concentrations correspond to sandstone levels with reddish or reddish-brown pigment. These pigments have been identified by Moessbauer spectroscopy. (Auth.)

Pore Structure and Diagenetic Controls on Relative Permeability: Implications for Enhanced Oil Recovery and CO2 Storage

Science.gov (United States)

Feldman, J.; Dewers, T. A.; Heath, J. E.; Cather, M.; Mozley, P.

2016-12-01

Multiphase flow in clay-bearing sandstones of the Morrow Sandstone governs the efficiency of CO2 storage and enhanced oil recovery at the Farnsworth Unit, Texas. This formation is the target for enhanced oil recovery and injection of one million metric ton of anthropogenically-sourced CO2. The sandstone hosts eight major flow units that exhibit distinct microstructural characteristics due to diagenesis, including: "clean" macro-porosity; quartz overgrowths constricting some pores; ghost grains; intergranular porosity filled by microporous authigenic clay; and feldspar dissolution. We examine the microstructural controls on macroscale (core scale) relative permeability and capillary pressure behavior through: X-ray computed tomography, Robomet.3d, and focused ion beam-scanning electron microscopy imaging of the pore structure of the major flow units of the Morrow Sandstone; relative permeability and capillary pressure in the laboratory using CO2, brine, and oil at reservoir pressure and effective stress conditions. The combined data sets inform links between patterns of diagenesis and multiphase flow. These data support multiphase reservoir simulation and performance assessment by the Southwest Regional Partnership on Carbon Sequestration (SWP). Funding for this project is provided by the U.S. Department of Energy's National Energy Technology Laboratory through the SWP under Award No. DE-FC26-05NT42591. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

In situ permeability testing of rock salt

International Nuclear Information System (INIS)

Peterson, E.W.; Lagus, P.L.; Broce, R.D.; Lie, K.

1981-04-01

Storage of transuranic (TRU) wastes in bedded salt formations requires a knowledge of the in situ permeability of SENM rock salt. Since assumptions for safety assessments have been made in which these wastes could generate gas pressures on the order of the lithostatic pressure over geologic time scales, the permeability of the surrounding formation becomes an important parameter for determining the manner in which the gases will be contained or dispersed. This report describes the series of tests conducted in the AEC-7 borehole, located near the WIPP site, to determine the in situ gas flow characteristics of the bedded salt. In these tests, compressed air was injected into the borehole and flow into the surrounding formation measured. These measured flow rates were interpreted in terms of formation permeabilities and porosities which were, in turn, used as modeling parameters for the repository response analysis. Two series of field tests were performed. The first series consisted of a number of whole-hole flow tests conducted to provide preliminary design information required for future operation of a guarded straddle packer system capable of measuring permeabilities > or = 0.1 μdarcy. The second series of tests were conducted using the Systems, Science and Software (S-Cubed) designed guarded straddle packer system. In these interval permeability tests, 100-foot lengths of borehole were isolated and the flow characteristics of the surrounding formation examined. In this report, a complete description of the test procedures, instrumentation, and measurement techniques is first given. The analytical/numerical methods used for data interpretation are then presented, followed by results of the interval and permeability tests. (The whole-hole tests are summarized in Appendix A.) Conclusions are presented in the final section

Relationship between characteristics of fan-delta sandstone bodies and in-situ leachable sandstone-type uranium mineralization

International Nuclear Information System (INIS)

Nie Fengjun; Zhou Weixun; Guan Taiyang; Li Sitian

2000-01-01

Like normal deltas, fan-deltas are composed of three parts, i.e., fan-delta plain, fan-delta front and pre-fin-delta, In-situ leachable uranium deposits are commonly distributed along the margins of in-land basins. The author analyzes the possible relationship between the basic characteristics of fan-delta sandstone bodies and uranium mineralization. Two examples, e.g., the fan delta depositional systems in the eastern part of Jungger basin and the southern part of Yili basin, are given to illustrate the fan-delta vertical sequence and planar distribution of sedimentary facies. It has been pointed out that the braided channel sandstone bodies on delta plain, sub-aqueous distributional channel sandstone bodies and delta front sandstone bodies may be the favourable host rocks for in-situ leachable sandstone uranium deposits

Recent Exploration Progresses on Sandstone-Hosted Uranium Deposits in Northwestern China

International Nuclear Information System (INIS)

Li Ziying

2014-01-01

Conclusions: 1. China nuclear power development is stimulating exploration for uranium resources. 2. Big progress on exploration for sandstonehosted uranium deposits have been made for recent years. 3. The combined exploration techniques are effectively used for locating ore beds and targeting uranium mineralization. 4. Metallogenic models have played important roles in expansion and new discoveries of u-deposits. 5. Uranium is very mobile and can be enriched in the different types of rocks. 6. Greenish sandstone is due to chlorite alteration by secondary reduction process related to oil and gas and can be used to indicate uranium mineralization.

Characterization of coal-derived hydrocarbons and source-rock potential of coal beds, San Juan Basin, New Mexico and Colorado, U.S.A.

Science.gov (United States)

Rice, D.D.; Clayton, J.L.; Pawlewicz, M.J.

1989-01-01

Coal beds are considered to be a major source of nonassociated gas in the Rocky Mountain basins of the United States. In the San Juan basin of northwestern New Mexico and southwestern Colorado, significant quantities of natural gas are being produced from coal beds of the Upper Cretaceous Fruitland Formation and from adjacent sandstone reservoirs. Analysis of gas samples from the various gas-producing intervals provided a means of determining their origin and of evaluating coal beds as source rocks. The rank of coal beds in the Fruitland Formation in the central part of the San Juan basin, where major gas production occurs, increases to the northeast and ranges from high-volatile B bituminous coal to medium-volatile bituminous coal (Rm values range from 0.70 to 1.45%). On the basis of chemical, isotopic and coal-rank data, the gases are interpreted to be thermogenic. Gases from the coal beds show little isotopic variation (??13C1 values range -43.6 to -40.5 ppt), are chemically dry (C1/C1-5 values are > 0.99), and contain significant amounts of CO2 (as much as 6%). These gases are interpreted to have resulted from devolatilization of the humic-type bituminous coal that is composed mainly of vitrinite. The primary products of this process are CH4, CO2 and H2O. The coal-generated, methane-rich gas is usually contained in the coal beds of the Fruitland Formation, and has not been expelled and has not migrated into the adjacent sandstone reservoirs. In addition, the coal-bed reservoirs produce a distinctive bicarbonate-type connate water and have higher reservoir pressures than adjacent sandstones. The combination of these factors indicates that coal beds are a closed reservoir system created by the gases, waters, and associated pressures in the micropore coal structure. In contrast, gases produced from overlying sandstones in the Fruitland Formation and underlying Pictured Cliffs Sandstone have a wider range of isotopic values (??13C1 values range from -43.5 to -38

Multi-scale nitrate transport in a sandstone aquifer system under intensive agriculture

Science.gov (United States)

Paradis, Daniel; Ballard, Jean-Marc; Lefebvre, René; Savard, Martine M.

2018-03-01

Nitrate transport in heterogeneous bedrock aquifers is influenced by mechanisms that operate at different spatial and temporal scales. To understand these mechanisms in a fractured sandstone aquifer with high porosity, a groundwater-flow and nitrate transport model—reproducing multiple hydraulic and chemical targets—was developed to explain the actual nitrate contamination observed in groundwater and surface water in a study area on Prince Edward Island, Canada. Simulations show that nitrate is leached to the aquifer year-round, with 61% coming from untransformed and transformed organic sources originating from fertilizers and manure. This nitrate reaches the more permeable shallow aquifer through fractures in weathered sandstone that represent only 1% of the total porosity (17%). Some of the nitrate reaches the underlying aquifer, which is less active in terms of groundwater flow, but most of it is drained to the main river. The river-water quality is controlled by the nitrate input from the shallow aquifer. Groundwater in the underlying aquifer, which has long residence times, is also largely influenced by the diffusion of nitrate in the porous sandstone matrix. Consequently, following a change of fertilizer application practices, water quality in domestic wells and the river would change rapidly due to the level of nitrate found in fractures, but a lag time of up to 20 years would be necessary to reach a steady level due to diffusion. This demonstrates the importance of understanding nitrate transport mechanisms when designing effective agricultural and water management plans to improve water quality.

Double porosity model to describe both permeability change and dissolution processes

International Nuclear Information System (INIS)

Niibori, Yuichi; Usui, Hideo; Chida, Taiji

2015-01-01

Cement is a practical material for constructing the geological disposal system of radioactive wastes. The dynamic behavior of both permeability change and dissolution process caused by a high pH groundwater was explained using a double porosity model assuming that each packed particle consists of the sphere-shaped aggregation of smaller particles. This model assumes two kinds of porosities between the particle clusters and between the particles, where the former porosity change mainly controls the permeability change of the bed, and the latter porosity change controls the diffusion of OH"- ions inducing the dissolution of silica. The fundamental equations consist of a diffusion equation of spherical coordinates of OH"- ions including the first-order reaction term and some equations describing the size changes of both the particles and the particle clusters with time. The change of over-all permeability of the packed bed is evaluated by Kozeny-Carman equation and the calculated radii of particle clusters. The calculated result well describes the experimental result of both permeability change and dissolution processes. (author)

Pore network properties of sandstones in a fault damage zone

Science.gov (United States)

Bossennec, Claire; Géraud, Yves; Moretti, Isabelle; Mattioni, Luca; Stemmelen, Didier

2018-05-01

The understanding of fluid flow in faulted sandstones is based on a wide range of techniques. These depend on the multi-method determination of petrological and structural features, porous network properties and both spatial and temporal variations and interactions of these features. The question of the multi-parameter analysis on fluid flow controlling properties is addressed for an outcrop damage zone in the hanging wall of a normal fault zone on the western border of the Upper Rhine Graben, affecting the Buntsandstein Group (Early Triassic). Diagenetic processes may alter the original pore type and geometry in fractured and faulted sandstones. Therefore, these may control the ultimate porosity and permeability of the damage zone. The classical model of evolution of hydraulic properties with distance from the major fault core is nuanced here. The hydraulic behavior of the rock media is better described by a pluri-scale model including: 1) The grain scale, where the hydraulic properties are controlled by sedimentary features, the distance from the fracture, and the impact of diagenetic processes. These result in the ultimate porous network characteristics observed. 2) A larger scale, where the structural position and characteristics (density, connectivity) of the fracture corridors are strongly correlated with both geo-mechanical and hydraulic properties within the damage zone.

Cathodoluminescence characteristics of sandstone and the implications for sandstone type No. 512 uranium deposit

International Nuclear Information System (INIS)

Liu Xiaodong; Guan Taiyang

1998-12-01

Cathodoluminescence (CL) technique, as a special petrologic tool, has been applied to the studies of uranium hosted sandstone from No. 512 uranium deposit located in Xinjiang Autonomous Region, Northwest China. The detrital grains including quartz, feldspar, debris and cements display distinguishing CL properties. The quartz grains mainly demonstrate brown and dark blue CL, feldspar grains demonstrate blue and bright blue CL, calcite cement displays bright yellow-orange and orange-red CL with significant CL zoning, while the debris, mud and sand cements have dark red CL, multicolor CL or non-luminescence. The characteristics of overgrowth, fracture healing, and the original contact relations of detrital grains appear much more significant with CL than that with conventional visual methods. Much more information can be contributed by CL technique to decipher the provenance area, to explain the cementation, consolidation and other diagenesis processes of sandstone. The CL technique also provides and efficient tool for identifying detrital grains and cements, and for more precisely estimating the proportions of various detrital grains and cement components in sandstone. The CL emission of uranium hosted sandstone revealed the existence of radiation-damage rims of quartz grains at the places with a little or no uranium minerals nearby, which may imply a uranium-leaching episode during the diagenesis of sandstone

Preliminary analysis of the sandstone accumulation situation at Sha-3 of the Paleogene Series Shakhetsze in the Khekou basin of the Tsziyan region

Energy Technology Data Exchange (ETDEWEB)

Chen, S

1984-01-01

The Khekou basin of the second order which is located in the Eastern part of the Tsziyan basin in the oil and gas Bokhayvan'skiy pool has an area of about 900 km/sup 2/. The main productive level occurs in sandstone beds in the Sha-3 subseries (reaching thickness of about 400 m) of the Shakhetsze series. The Bonan oil field was discovered in this region in 1975. The initially productive deposits were viewed as fluvial-delta; however, studies of recent years, including investigation of the sedimentation sequences and the structures that mark the surfaces of the microscopic level in the core sample, together with an analysis of borehole geophysical data, indicated that the sandy bodies of the productive beds in the basin must be viewed as deposits of turbidite flows and deposits of gravitational flows in channels. Insofar as distribution of the turbidite sandstones differs significantly from the delta, this led to a review of the long-term trends in the neighboring fields.

The influence of wall permeability on laminar and turbulent flows : Theory and simulations

NARCIS (Netherlands)

Breugem, W.P.

2005-01-01

The study of flows over permeable walls is relevant to many applications. Examples are flows over and through porous river beds, vegetation, snow, heat exchangers of foam metal, and oil wells. The main objectives of this thesis are to gain insight in the influence of wall permeability on both

Experimental study of very low permeability rocks using a high accuracy permeameter

International Nuclear Information System (INIS)

Larive, Elodie

2002-01-01

The measurement of fluid flow through 'tight' rocks is important to provide a better understanding of physical processes involved in several industrial and natural problems. These include deep nuclear waste repositories, management of aquifers, gas, petroleum or geothermal reservoirs, or earthquakes prevention. The major part of this work consisted of the design, construction and use of an elaborate experimental apparatus allowing laboratory permeability measurements (fluid flow) of very low permeability rocks, on samples at a centimetric scale, to constrain their hydraulic behaviour at realistic in-situ conditions. The accuracy permeameter allows the use of several measurement methods, the steady-state flow method, the transient pulse method, and the sinusoidal pore pressure oscillation method. Measurements were made with the pore pressure oscillation method, using different waveform periods, at several pore and confining pressure conditions, on different materials. The permeability of one natural standard, Westerly granite, and an artificial one, a micro-porous cement, were measured, and results obtained agreed with previous measurements made on these materials showing the reliability of the permeameter. A study of a Yorkshire sandstone shows a relationship between rock microstructure, permeability anisotropy and thermal cracking. Microstructure, porosity and permeability concepts, and laboratory permeability measurements specifications are presented, the permeameter is described, and then permeability results obtained on the investigated materials are reported [fr

"Sydney sandstone": Heritage Stone from Australia

Science.gov (United States)

Cooper, Barry; Kramar, Sabina

2014-05-01

Sydney is Australia's oldest city being founded in 1788. The city was fortunate to be established on an extensive and a relatively undeformed layer of lithified quartz sandstone of Triassic age that has proved to be an ideal building stone. The stone has been long identified by geologists as the Hawkesbury Sandstone. On the other hand the term "Sydney sandstone" has also been widely used over a long period, even to the extent of being utilised as the title of published books, so its formal designation as a heritage stone will immediately formalise this term. The oldest international usage is believed to be its use in the construction of the Stone Store at Kerikeri, New Zealand (1832-1836). In the late 19th century, public buildings such as hospitals, court houses as well as the prominent Sydney Town Hall, Sydney General Post Office, Art Gallery of New South Wales, State Library of New South Wales as well as numerous schools, churches, office building buildings, University, hotels, houses, retaining walls were all constructed using Sydney sandstone. Innumerable sculptures utilising the gold-coloured stone also embellished the city ranging from decorative friezes and capitals on building to significant monuments. Also in the late 19th and early 20th century, Sydney sandstone was used for major construction in most other major Australian cities especially Melbourne, Adelaide and Brisbane to the extent that complaints were expressed that suitable local stone materials were being neglected. Quarrying of Sydney sandstone continues today. In 2000 it was recorded noted that there were 33 significant operating Sydney sandstone quarries including aggregate and dimension stone operations. In addition sandstone continues to be sourced today from construction sites across the city area. Today major dimension stone producers (eg Gosford Quarries) sell Sydney sandstone not only into the Sydney market but also on national and international markets as cladding and paving products

Analysis of metallogenic conditions of sandstone type uranium deposits in interlayer oxidation zone in the northwest of Junggar basin, Xinjiang

International Nuclear Information System (INIS)

Lin Shuangxing

1997-01-01

From various aspects such as the basin structures, structure features of the sedimentary cover, lithofacies features of basin sediments, geochemical characteristics of sedimentary rocks, regional hydrogeologic conditions and epigenetic reworking of the sedimentary cover and so on, the author analyzes the metallogenic conditions of sandstone type uranium deposits in interlayer oxidation zone in the northwest of Junggar basin. The author proposes that the area has abundant uranium sources, and possesses favourable stratigraphic combinations for the development of interlayer oxidation zone. Secondarily oxidized sandstone bodies present universally at places from the source area to stream channel facies. Reducing beds and secondarily reducing barrier are developed at the front of the secondarily oxidized sandstone body. The tectonic features of the sedimentary cover indicate that the area belongs to a relatively-stable suborogenic region and possesses secondary mobilization and reworking conditions during the uplifting and contraction stage of the basin. Epigenetic metallization is evident in the sedimentary cover of the basin

Anatomy and dimensions of fluvial crevasse-splay deposits: Examples from the Cretaceous Castlegate Sandstone and Neslen Formation, Utah, U.S.A.

Science.gov (United States)

Burns, C. E.; Mountney, N. P.; Hodgson, D. M.; Colombera, L.

2017-04-01

Crevasse-splay deposits form a volumetrically significant component of many fluvial overbank successions (up to 90% in some successions).Yet the relationships between the morphological form of accumulated splay bodies and their internal facies composition remains poorly documented from ancient successions. This work quantifies lithofacies distributions and dimensions of exhumed crevasse-splay architectural elements in the Campanian Castlegate Sandstone and Neslen Formation, Mesaverde Group, Utah, USA, to develop a depositional model. Fluvial crevasse-splay bodies thin from 2.1 m (average) to 0.8 m (average) and fine from a coarsest recorded grain size of lower-fine sand to fine silt away from major trunk channel bodies. Internally, the preserved deposits of splays comprise laterally and vertically variable sandstone and siltstone facies associations: proximal parts are dominated by sharp and erosional-based sandstone-prone units, which may be structureless or may comprise primary current lineation on beds and erosional gutter casts; medial parts comprise sets of climbing-ripple strata and small scale deformed beds; distal parts comprise sets of lower-stage plane beds and complex styles of lateral grading into fine-grained floodbasin siltstones and coals. Lithofacies arrangements are used to establish the following: (i) recognition criteria for crevasse-splay elements; (ii) criteria for the differentiation between distal parts of crevasse-splay bodies and floodplain fines; and (iii) empirical relationships with which to establish the extent (ca. 500 m long by 1000 m wide) and overall semi-elliptical planform shape of crevasse-splay bodies. These relationships have been established by high-resolution stratigraphic correlation and palaeocurrent analysis to identify outcrop orientation with respect to splay orientation. This permits lateral changes in crevasse-splay facies architecture to be resolved. Facies models describing the sedimentology and architecture of

Investigated Miscible CO2 Flooding for Enhancing Oil Recovery in Wettability Altered Chalk and Sandstone Rocks

Energy Technology Data Exchange (ETDEWEB)

Tabrizy, Vahid Alipour

2012-07-01

The thesis addresses oil recovery by miscible CO2 flooding from modified sandstone and chalk rocks. Calcite mineral surface is modified with stearic acid (SA) and asphaltene, and the silicate mineral surfaces are modified with N,N-dimethyldodecylamine (NN-DMDA) and asphaltene. The stability of adsorbed polar components in presence of SO4 2- and Mg2 + ions is also investigated. Recovery from sandstone cores is consistently lower than that from chalk cores saturated with the same oil and flooded with CO2 at all miscible flooding conditions. This may be due to the larger permeability contrasts in sandstone cores, which promote the fingering phenomenon. Miscible CO2 flooding for chalk and sandstone cores with distilled water, as initial water saturation, shows also lower oil recovery than cores saturated with different ions. At higher miscible flooding conditions, higher oil recovery is obtained. However, presence of light components (such as C1 or C3) in oil reduced the recovery. Oil recovery in presence of methane (C1) is lower than that in presence of methane and propane (C1/C3). A ternary diagram was constructed in order to understand the CO2 flooding mechanism(s) at the different flooding conditions and in presence of light components. The side effect of the flooding with CO2 is the probability for asphaltene deposition. An approach based on solubility parameter in the liquid, is used to assess the risk for asphaltene deposition during CO2 miscible flooding. The light components (C1/C3) and higher flooding conditions enhanced the risk for asphaltene instability. It is also shown higher amount of asphaltene deposition in chalk cores than that in sandstone cores at similar miscibility conditions.(au)

Fluid flow with heat transfer in a fix-bed

International Nuclear Information System (INIS)

Gasparetto, C.A.

1982-01-01

Tests with two different fluids, water and air, flowing in a bed with irregular particles of silica were done. The bed was confined inside a tube, which was heated by an external jacket. The bed is characterized by permeability and porosity. The tests showed a wall effect face to the relation between the tube diameter and the medium dimension of the particles. The results are presented as a relation between Nusselt number / Peclet number. (E.G.) [pt

A Reconciliation of Packed Column Permeability Data: Column Permeability as a Function of Particle Porosity

Directory of Open Access Journals (Sweden)

Hubert M. Quinn

2014-01-01

Full Text Available In his textbook teaching of packed bed permeability, Georges Guiochon uses mobile phase velocity as the fluid velocity term in his elaboration of the Darcy permeability equation. Although this velocity frame makes a lot of sense from a thermodynamic point of view, it is valid only with respect to permeability at a single theoretical boundary condition. In his more recent writings, however, Guiochon has departed from his long-standing mode of discussing permeability in terms of the Darcy equation and has embraced the well-known Kozeny-Blake equation. In this paper, his teaching pertaining to the constant in the Kozeny-Blake equation is examined and, as a result, a new correlation coefficient is identified and defined herein based on the velocity frame used in his teaching. This coefficient correlates pressure drop and fluid velocity as a function of particle porosity. We show that in their experimental protocols, Guiochon et al. have not adhered to a strict material balance of permeability which creates a mismatch of particle porosity and leads to erroneous conclusions regarding the value of the permeability coefficient in the Kozeny-Blake equation. By correcting the experimental data to properly reflect particle porosity we reconcile the experimental results of Guiochon and Giddings, resulting in a permeability reference chart which is presented here for the first time. This reference chart demonstrates that Guiochon’s experimental data, when properly normalized for particle porosity and other related discrepancies, corroborates the value of 267 for the constant in the Kozeny-Blake equation which was derived by Giddings in 1965.

Principal permeability determination from multiple horizontal well tests

Energy Technology Data Exchange (ETDEWEB)

Economides, M. [Texas A and M Univ., TX (United States); Munoz, A.; Ehlig-Economides, C.

1998-12-31

A method for obtaining principal permeability magnitudes and direction that requires only the linear flow regime from transient tests in three horizontal wells oriented in three distinct and arbitrary directions, is described. Well design optimization strategies require knowledge of both the principal permeability orientation as well as the horizontal permeability magnitudes. When the degree of horizontal permeability anisotropy (i.e. permeability in the bedding plane with respect to direction) is significant, the productivity of a long horizontal well will depend greatly on its direction, especially when the well is first brought into production. Productivities have been found to deviate substantially among wells in the same reservoir and this deviation has been attributed to differences in well orientation. In view of this fact, measuring permeability anisotropy becomes a compelling necessity. The success of the proposed method is illustrated by a case study in which the principal permeability magnitudes and direction from three wells were used to predict the productivity of a fourth well within 10 per cent. Use of the computed principal permeabilities from the case study, it was possible to forecast the cumulative production to show the significance of well trajectory optimization on the discounted cash flow and the net present value. 20 refs., 3 figs.

Clay squirt: Local flow dispersion in shale-bearing sandstones

DEFF Research Database (Denmark)

Sørensen, Morten Kanne; Fabricius, Ida Lykke

2017-01-01

Dispersion of elastic-wave velocity is common in sandstone and larger in shaly sandstone than in clean sandstone. Dispersion in fluid-saturated shaly sandstone often exceeds the level expected from the stress-dependent elastic moduli of dry sandstone. The large dispersion has been coined clay...... squirt and is proposed to originate from a pressure gradient between the clay microporosity and the effective porosity. We have formulated a simple model that quantifies the clay-squirt effect on bulk moduli of sandstone with homogeneously distributed shale laminae or dispersed shale. The model...... predictions were compared with the literature data. For sandstones with dispersed shale, agreement was found, whereas other sandstones have larger fluid-saturated bulk modulus, possibly due to partially load-bearing shales or heterogeneous shale distribution. The data that agree with the clay-squirt model...

Two-phase flow in beds of spherical particles

International Nuclear Information System (INIS)

Schulenberg, T.; Mueller, U.

1984-02-01

A refined model for two-phase flow in beds of uniform spherical particles is presented. It includes the influence of interfacial drag forces between liquid and gas, which are important in beds of coarse particles, and an incrase of porosity due to vapour channels or similiar irreversible bed disturbances, which occur in beds of fine particles. The model is based on the momentum equations for separated flow, which are closed with empirical relations for wall shear stress and interfacial drag. To improve this model it is applied to volumetrically heated beds on a adiabatic bottom, which are saturated and superimposed with a boiling liquid. In case of fine particles only an impermeable bottom is considered, whereas in case of coarse particles also beds on a permeable support are discussed. (orig.) [de

Sedimentological analysis and bed thickness statistics from a Carboniferous deep-water channel-levee complex: Myall Trough, SE Australia

Science.gov (United States)

Palozzi, Jason; Pantopoulos, George; Maravelis, Angelos G.; Nordsvan, Adam; Zelilidis, Avraam

2018-02-01

This investigation presents an outcrop-based integrated study of internal division analysis and statistical treatment of turbidite bed thickness applied to a Carboniferous deep-water channel-levee complex in the Myall Trough, southeast Australia. Turbidite beds of the studied succession are characterized by a range of sedimentary structures grouped into two main associations, a thick-bedded and a thin-bedded one, that reflect channel-fill and overbank/levee deposits, respectively. Three vertically stacked channel-levee cycles have been identified. Results of statistical analysis of bed thickness, grain-size and internal division patterns applied on the studied channel-levee succession, indicate that turbidite bed thickness data seem to be well characterized by a bimodal lognormal distribution, which is possibly reflecting the difference between deposition from lower-density flows (in a levee/overbank setting) and very high-density flows (in a channel fill setting). Power law and exponential distributions were observed to hold only for the thick-bedded parts of the succession and cannot characterize the whole bed thickness range of the studied sediments. The succession also exhibits non-random clustering of bed thickness and grain-size measurements. The studied sediments are also characterized by the presence of statistically detected fining-upward sandstone packets. A novel quantitative approach (change-point analysis) is proposed for the detection of those packets. Markov permutation statistics also revealed the existence of order in the alternation of internal divisions in the succession expressed by an optimal internal division cycle reflecting two main types of gravity flow events deposited within both thick-bedded conglomeratic and thin-bedded sandstone associations. The analytical methods presented in this study can be used as additional tools for quantitative analysis and recognition of depositional environments in hydrocarbon-bearing research of ancient

Relationship between petrographic pore types and core measurements in sandstones of the Monserrate Formation, upper Magdalena Valley, Colombia

International Nuclear Information System (INIS)

Ehrlich, R; Cobaleda, G; Barclay, Ferm

1997-01-01

Patterns of porosity in sandstones of the Monserrate Formation (Upper Magdalena Valley) exposed in polished blocks have been digitally recorded using an image processor coupled to a scanning electron microscope operated in back scatter electron mode. Additionally, porosity, permeability and response to mercury injection-capillary pressure tests were measured on some of the imaged samples. Porosity pattern were evaluated via an erosion/dilation-differencing image-processing algorithm and then classified by the self-training classifier, SAWVEC. Changes in the resulting pore type proportions were strongly associated with changes in the mercury porosimetry curves. From the image processing data, five pore types, sufficient to include all of the variability in size and shape of the patterns of porosity, were identified. Variations in the number of pares of each type per unit cross sectional area were related to variations in permeability. The resultant relationships with mercury porosimetry demonstrated that pares of the same type tends to form microcircuits characterized by a limited throat size range. Permeability modeling showed that intergranular Pare Types 2 and 4 (secondary porosity resulting from carbonate dissolution) are responsible for permeability in the 0,01 - 0,1 0 Darcy range. Type 5 pares (large molds) slightly contribute to permeability, except in coarse grained rocks where they are efficiently connected by micro fractures

Experimental strain analysis of Clarens Sandstone colonised by endolithic lichens

Directory of Open Access Journals (Sweden)

D. Wessels

1995-08-01

Full Text Available Endolithic lichens occur commonly on Clarens Sandstone in South Africa, where they significantly contribute to the weathering of sandstone by means of mechanical and chemical weathering processes. This preliminary investigation reports on the success- ful use of strain gauges in detecting strain differences between sandstone without epilithic lichens and sandstone colonised by the euendolithic lichen Lecidea aff. sarcogynoides Korb. Mechanical weathering, expressed as strain changes, in Clarens Sandstone was studied during the transition from relatively dry winter to wet summer conditions. Daily weathering of sandstone due to thermal expansion and contraction of colonised and uncolonised sandstone could be shown. Our results show that liquid water in sandstone enhances the mechanical weathering of uncolonised Clarens Sandstone while water in the gaseous phase enhances mechanical weathering of sandstone by euendolithic lichens.

Geothermal characteristics of Buntsandstein sandstone reservoir of Alsace

International Nuclear Information System (INIS)

Haffen, Sebastien

2012-01-01

The Buntsandstein, located in the Upper Rhine Graben, appears to be an easy target for geothermal exploitation, linking sandstone and clay with the regional thermal anomaly. This study aims at characterizing petrophysical characteristics of these sandstones as well as the fracturing affecting them, with the intention of providing a conceptual model of the formation which will act as guide for future exploitation. The sedimentary facies are composed by five petrographical facies (clean sandstones, sandstones with clayey coating, clay matrix sandstones, silicified sandstones and carbonated matrix sandstones) which split with variable proportions and control a part of petrophysical properties measured at matrix scale. The comparison between petrophysical data, macroscopic data from temperature gradient analysis, modelling data and fracturing, allows the building of a Buntsandstein Sandstones fluids circulation conceptual model. This analysis points the role of the damage zone of fault zones for fluids transfer at large scale, but also that of two sedimentary facies: marginal erg and Playa Lake. The analysis of different outcrops shows that the fracturing evolves according to the situation in the sedimentary pile and according to the situation in comparison with major tectonic accidents. (author) [fr

Genesis and distribution pattern of carbonate cements in lacustrine deep-water gravity-flow sandstone reservoirs in the third member of the Shahejie Formation in the Dongying Sag, Jiyang Depression, Eastern China

DEFF Research Database (Denmark)

Yang, Tian; Cao, Yingchang; Friis, Henrik

2018-01-01

The lacustrine deep-water gravity-flow sandstone reservoirs in the third member of the Shahejie Formation are the main exploration target for hydrocarbons in the Dongying Sag, Eastern China. Carbonate cementation is responsible for much of the porosity and permeability reduction in the lacustrine...

Experimental study of very-low permeability rocks by the implementation of a precision permeameter

International Nuclear Information System (INIS)

Larive, E.

2002-12-01

The measurement of fluid flow through 'tight' rocks is important to provide a better understanding of physical processes involved in several industrial and natural problems. These include deep nuclear waste repositories, management of aquifers, gas, petroleum or geothermal reservoirs, or earthquakes prevention. The major part of this work consisted of the design, construction and use of an elaborate experimental apparatus allowing laboratory permeability measurements (fluid flow) of very low permeability rocks, on samples at a centimetric scale, to constrain their hydraulic behaviour at realistic in-situ conditions.The accuracy permeameter allows the use of several measurement methods, the steady-state flow method, the transient pulse method and the sinusoidal pore pressure oscillation method. Measurements were made with the pore pressure oscillation method, using different waveform periods, at several pore and confining pressure conditions on different materials. The permeability of one natural standard, Westerly granite, and an artificial one, a micro-porous cement, were measured and results obtained agreed with previous measurements made on these materials showing the reliability of the permeameter. A study of a Yorkshire sandstone shows a relationship between rock microstructure, permeability anisotropy and thermal cracking. Microstructure, porosity and permeability concepts, and laboratory permeability measurements specifications are presented, the permeameter is described, and then permeability results obtained on the investigated materials are reported. (author)

Pleistocene volcanism of Bed I, Olduvai Gorge, Tanzania: chemostratigraphy, sedimentology, and paleoecology

OpenAIRE

Habermann, Jörg

2016-01-01

Chapter 2 addresses correlation difficulties in Bed I that arise from major lateral facies changes combined with discontinuous exposure using the discriminative power of the chemical composition of major juvenile mineral phases (augite, anorthoclase, plagioclase) from tuffs, volcaniclastic sandstones, siliciclastic units, and lavas. These compositions, obtained from electron probe micro-analysis, are statistically evaluated applying principal component analysis and discriminant analysis to de...

Thermally induced permeability reduction due to particle migration in sandstones: the effect of temperature on kaolinite mobilisation and aggregation

DEFF Research Database (Denmark)

Rosenbrand, Esther; Fabricius, Ida Lykke; Yuan, Hao

2012-01-01

The seasonal imbalance in supply and demand of renewable energy requires seasonal storage, which potentially may be achieved by hot water injection in geothermal aquifers to minimize heat loss by advection. A reduction of porosity and permeability is a risk of heating the rock above the in...... the interaction energy between quartz and kaolinite particles for different saturating fluids. The results are compared to the published data addressing the effect of temperature on permeability. This provides a qualitative explanation for the observed changes in permeability with temperature for the tests...

Tectonic and sedimentological environments of sandstone-hosted uranium deposits, with special reference to the Karoo Basin of South Africa

International Nuclear Information System (INIS)

Le Roux, J.P.

1985-01-01

The principal tectonic and sedimentological settings for sandstone-hosted uranium deposits are described. Back-arc basins filled with post-Silurian, fluvial sediments bordering subduction zone magmatic arcs of calc-alkaline composition are considered favourable tectonic environments. The basins should be closed to prevent excessive oxidation of the sediments. Uranium deposits are concentrated near basin rims in the transition zone between uplift and basin subsidence, because of favourable sedimentary facies in those areas. Syn- and post-depositional deformation could have affected the localisation of uranium ore-bodies, while intrusive centres or uplifted arcs commonly have surrounding aprons of potential host rocks. Stratigraphic zoning is also related to source area tectonics and can be used to predict favourable sedimentary environments. Sedimentological processes had a direct influence on the permeability and carbonaceous matter content of sandstones and therefore have often controlled the localisation of ore-bodies. (author)

Experimental Investigation of Crack Extension Patterns in Hydraulic Fracturing with Shale, Sandstone and Granite Cores

Directory of Open Access Journals (Sweden)

Jianming He

2016-12-01

Full Text Available Hydraulic fracturing is an important method of reservoir stimulation in the exploitation of geothermal resources, and conventional and unconventional oil and gas resources. In this article, hydraulic fracturing experiments with shale, sandstone cores (from southern Sichuan Basin, and granite cores (from Inner Mongolia were conducted to investigate the different hydraulic fracture extension patterns in these three reservoir rocks. The different reactions between reservoir lithology and pump pressure can be reflected by the pump pressure monitoring curves of hydraulic fracture experiments. An X-ray computer tomography (CT scanner was employed to obtain the spatial distribution of hydraulic fractures in fractured shale, sandstone, and granite cores. From the microscopic and macroscopic observation of hydraulic fractures, different extension patterns of the hydraulic fracture can be analyzed. In fractured sandstone, symmetrical hydraulic fracture morphology could be formed, while some micro cracks were also induced near the injection hole. Although the macroscopic cracks in fractured granite cores are barely observed by naked eye, the results of X-ray CT scanning obviously show the morphology of hydraulic fractures. It is indicated that the typical bedding planes well developed in shale formation play an important role in the propagation of hydraulic fractures in shale cores. The results also demonstrated that heterogeneity influenced the pathway of the hydraulic fracture in granite cores.

Utilization of the St. Peter Sandstone in the Illinois Basin for CO2 Sequestration

Energy Technology Data Exchange (ETDEWEB)

Will, Robert; Smith, Valerie; Leetaru, Hannes

2014-09-30

This project is part of a larger project co-funded by the United States Department of Energy (US DOE) under cooperative agreement DE-FE0002068 from 12/08/2009 through 9/31/2014. The study is to evaluate the potential of formations within the Cambro-Ordovician strata above the Mt. Simon Sandstone as potential targets for carbon dioxide (CO2) sequestration in the Illinois and Michigan Basins. This report evaluates the potential injectivity of the Ordovician St. Peter Sandstone. The evaluation of this formation was accomplished using wireline data, core data, pressure data, and seismic data acquired through funding in this project as well as existing data from two additional, separately funded projects: the US DOE funded Illinois Basin – Decatur Project (IBDP) being conducted by the Midwest Geological Sequestration Consortium (MGSC) in Macon County, Illinois, and the Illinois Industrial Carbon Capture and Sequestration (ICCS) Project funded through the American Recovery and Reinvestment Act (ARRA), which received a phase two award from DOE. This study addresses the question of whether or not the St. Peter Sandstone may serve as a suitable target for CO2 sequestration at locations within the Illinois Basin where it lies at greater depths (below the underground source of drinking water (USDW)) than at the IBDP site. The work performed included numerous improvements to the existing St. Peter reservoir model created in 2010. Model size and spatial resolution were increased resulting in a 3 fold increase in the number of model cells. Seismic data was utilized to inform spatial porosity distribution and an extensive core database was used to develop porosity-permeability relationships. The analysis involved a Base Model representative of the St. Peter at “in-situ” conditions, followed by the creation of two hypothetical models at in-situ + 1,000 feet (ft.) (300 m) and in-situ + 2,000 ft. (600 m) depths through systematic depthdependent adjustment of the Base Model

Dynamic fluid connectivity during steady-state multiphase flow in a sandstone.

Science.gov (United States)

Reynolds, Catriona A; Menke, Hannah; Andrew, Matthew; Blunt, Martin J; Krevor, Samuel

2017-08-01

The current conceptual picture of steady-state multiphase Darcy flow in porous media is that the fluid phases organize into separate flow pathways with stable interfaces. Here we demonstrate a previously unobserved type of steady-state flow behavior, which we term "dynamic connectivity," using fast pore-scale X-ray imaging. We image the flow of N 2 and brine through a permeable sandstone at subsurface reservoir conditions, and low capillary numbers, and at constant fluid saturation. At any instant, the network of pores filled with the nonwetting phase is not necessarily connected. Flow occurs along pathways that periodically reconnect, like cars controlled by traffic lights. This behavior is consistent with an energy balance, where some of the energy of the injected fluids is sporadically converted to create new interfaces.

Compositional and Relative Permeability Hysteresis Effects on Near-Miscible WAG

DEFF Research Database (Denmark)

Christensen, Jes Reimer; Stenby, Erling Halfdan; Skauge, Arne

1998-01-01

Evaluation of compositional effects and fluid flow description on near-miscible (water-alternating-gas) WAG modeling have been studied for a North Sea oil field starting production in 1998. A sector model with four wells was applied to simulate a heterogeneous sandstone reservoir, and a compositi......Evaluation of compositional effects and fluid flow description on near-miscible (water-alternating-gas) WAG modeling have been studied for a North Sea oil field starting production in 1998. A sector model with four wells was applied to simulate a heterogeneous sandstone reservoir......, and a compositional model was used to compare different production strategies e.g. waterflooding and a near-miscible (WAG) injection. In the WAG scheme both dry and wet (rich) hydrocarbon gases have been considered for injection. The phase behaviour was quantified by comparing the performance of the different...... injection gases. Result obtained shows the WAG injection gives improved recovery compared to water injection, due to better sweep and lower residual oil saturation. Simulations with and without relative permeability hysteresis (two-phase model) were compared. The effect of trapped gas on oil recovery does...

Using artificial intelligence to predict permeability from petrographic data

Energy Technology Data Exchange (ETDEWEB)

Maqsood Ali; Adwait Chawathe [New Mexico Petroleum Recovery Research Centre (Mexico)

2000-10-01

Petrographic data collected during thin section analysis can be invaluable for understanding the factors that control permeability distribution. Reliable prediction of permeability is important for reservoir characterization. The petrographic elements (mineralogy, porosity types, cements and clays, and pore morphology) interact with each other uniquely to generate a specific permeability distribution. It is difficult to quantify accurately this interaction and its consequent effect on permeability, emphasizing the non-linear nature of the process. To capture these non-linear interactions, neural networks were used to predict permeability from petrographic data. The neural net was used as a multivariate correlative tool because of its ability to learn the non-linear relationships between multiple input and output variables. The study was conducted on the upper Queen formation called the Shattuck Member (Permian age). The Shattuck Member is composed of very fine-grained arkosic sandstone. The core samples were available from the Sulimar Queen and South Lucky Lake fields located in Chaves County, New Mexico. Nineteen petrographic elements were collected for each permeability value using a combined minipermeameter-petrographic technique. In order to reduce noise and overfitting the permeability model, these petrographic elements were screened, and their control (ranking) with respect to permeability was determined using fuzzy logic. Since the fuzzy logic algorithm provides unbiased ranking, it was used to reduce the dimensionality of the input variables. Based on the fuzzy logic ranking, only the most influential petrographic elements were selected as inputs for permeability prediction. The neural net was trained and tested using data from Well 1-16 in the Sulimar Queen field. Relying on the ranking obtained from the fuzzy logic analysis, the net was trained using the most influential three, five, and ten petrographic elements. A fast algorithm (the scaled conjugate

Squeeze-film flow between a flat impermeable bearing and an anisotropic porous bed

Science.gov (United States)

Karmakar, Timir; Raja Sekhar, G. P.

2018-04-01

We consider a theoretical model of the squeeze film in the presence of a porous bed. The gap between the porous bed and the bearing is assumed to be filled with a Newtonian fluid. We use the Navier-Stokes equation in the fluid region and the Darcy equation in the fluid filled porous region. Lubrication approximation is used to derive the corresponding evolution equation for the film thickness. We use G. S. Beavers and D. D. Joseph ["Boundary conditions at a naturally permeable wall," J. Fluid. Mech. 30, 197-207 (1967)] and M. Le Bars and M. G. Worster ["Interfacial conditions between a pure fluid and a porous medium: Implications for binary alloy solidification," J. Fluid. Mech. 550, 149-173 (2006)] condition at the liquid porous interface and present a detailed analysis on the corresponding impact. We assume that the porous bed is anisotropic in nature with permeabilities K2 and K1 along the principal axes. Accordingly, the anisotropic angle ϕ is taken as the angle between the horizontal direction and principal axis with permeability K2. We show that the anisotropic permeability ratio and the anisotropic angle make a significant influence on the contact time, flux, velocity, etc. Contact time to meet the porous bed when a bearing approaches under a constant prescribed load is estimated. We present some important findings (relevant to the knee joint) based on the anisotropic properties of the human cartilage. For a prescribed constant load, we have estimated the time duration, during which a healthy human knee remains fluid lubricated.

On the Theory of Solitons of Fluid Pressure and Solute Density in Geologic Porous Media, with Applications to Shale, Clay and Sandstone

Science.gov (United States)

Caserta, A.; Kanivetsky, R.; Salusti, E.

2017-11-01

We here analyze a new model of transients of pore pressure p and solute density ρ in geologic porous media. This model is rooted in the nonlinear wave theory, its focus is on advection and effect of large pressure jumps on strain. It takes into account nonlinear and also time-dependent versions of the Hooke law about stress, rate and strain. The model solutions strictly relate p and ρ evolving under the effect of a strong external stress. As a result, the presence of quick and sharp transients in low permeability rocks is unveiled, i.e., the nonlinear "Burgers solitons". We, therefore, show that the actual transport process in porous rocks for large signals is not only the linear diffusion, but also a solitons presence could control the process. A test of a presence of solitons is applied to Pierre shale, Bearpaw shale, Boom clay and Oznam-Mugu silt and clay. An application about the presence of solitons for nuclear waste disposal and salt water intrusions is also discussed. Finally, in a kind of "theoretical experiment" we show that solitons could also be present in higher permeability rocks (Jordan and St. Peter sandstones), thus supporting the idea of a possible occurrence of osmosis also in sandstones.

The Paleozoic-Mesozoic recycling of the Rakaia Terrane, South Island, New Zealand : sandstone clast and sandstone petrology, geochemistry, and geochronology

International Nuclear Information System (INIS)

Wandres, A.M.; Bradshaw, J.D.; Ireland, T.

2005-01-01

The Torlesse terranes - part of the New Zealand Eastern Province - are accretionary complexes that comprise an enormous volume of quartzofeldspathic sandstones and mudstones with subsidiary conglomerates plus minor oceanic assemblages. Two terranes are recognised in the South Island - the Permian to Late Triassic Rakaia Terrane and the Late Jurassic to Early Cretaceous Pahau Terrane. Sandstone clasts from two Rakaia Terrane and two Pahau Terrane conglomerates were collected. We present the first combined detailed information on petrography and geochemistry of Torlesse conglomerate sandstone clasts and use our own and published U-Pb SHRIMP detrital zircon age data to demonstrate the recycling of the Rakaia Terrane into Rakaia strata itself and into Pahau Terrane strata. Sandstone clast major and trace element chemical data largely support petrographic observations derived from thin-section analysis. The similarities of petrographic and geochemical data between sandstone clasts from the Rakaia Terrane and Rakaia sandstones suggest that clasts in the Permian Te Moana and Late Triassic Lake Hill Conglomerates were derived by autocannibalistic reworking of older, consolidated, Rakaia sediments. Data from sandstone clasts from the Pahau Terrane suggest that uplift of the Rakaia Terrane continued into the Cretaceous. These Pahau Terrane clasts indicate that at the time of the Pahau sedimentation Permian to early Late Triassic Rakaia rocks were exposed and recycled into the Pahau Basin. (author). 57 refs., 8 figs., 3 tables

Porosity, single-phase permeability, and capillary pressure data from preliminary laboratory experiments on selected samples from Marker Bed 139 at the Waste Isolation Pilot Plant. Volume 1 of 3: Main report, appendix A

Energy Technology Data Exchange (ETDEWEB)

Howarth, S.M.; Christian-Frear, T.

1997-08-01

Three groups of core samples from Marker Bed 139 of the Salado Formation at the Waste Isolation Pilot Plant (WIPP) were analyzed to provide data to support the development of numerical models used to predict the long-term hydrologic and structural response of the WIPP repository. These laboratory experiments, part of the FY93 Experimental Scoping Activities of the Salado Two-Phase Flow Laboratory Program, were designed to (1) generate WIPP-specific porosity and single-phase permeability data, (2) provide information needed to design and implement planned tests to measure two-phase flow properties, including threshold pressure, capillary pressure, and relative permeability, and (3) evaluate the suitability of using analog correlations for the Salado Formation to assess the long-term performance of the WIPP. This report contains a description of the boreholes core samples, the core preparation techniques used, sample sizes, testing procedures, test conditions, and results of porosity and single-phase permeability tests performed at three laboratories: TerraTek, Inc. (Salt Lake City, UT), RE/SPEC, Inc. (Rapid City, SD), and Core Laboratories-Special Core Analysis Laboratory (Carrollton, TX) for Rock Physics Associates. In addition, this report contains the only WIPP-specific two-phase-flow capillary-pressure data for twelve core samples. The WIPP-specific data generated in this laboratory study and in WIPP field-test programs and information from suitable analogs will form the basis for specification of single- and two-phase flow parameters for anhydrite markers beds for WIPP performance assessment calculations.

Porosity, single-phase permeability, and capillary pressure data from preliminary laboratory experiments on selected samples from Marker Bed 139 at the Waste Isolation Pilot Plant. Volume 1 of 3: Main report, appendix A

International Nuclear Information System (INIS)

Howarth, S.M.; Christian-Frear, T.

1997-08-01

Three groups of core samples from Marker Bed 139 of the Salado Formation at the Waste Isolation Pilot Plant (WIPP) were analyzed to provide data to support the development of numerical models used to predict the long-term hydrologic and structural response of the WIPP repository. These laboratory experiments, part of the FY93 Experimental Scoping Activities of the Salado Two-Phase Flow Laboratory Program, were designed to (1) generate WIPP-specific porosity and single-phase permeability data, (2) provide information needed to design and implement planned tests to measure two-phase flow properties, including threshold pressure, capillary pressure, and relative permeability, and (3) evaluate the suitability of using analog correlations for the Salado Formation to assess the long-term performance of the WIPP. This report contains a description of the boreholes core samples, the core preparation techniques used, sample sizes, testing procedures, test conditions, and results of porosity and single-phase permeability tests performed at three laboratories: TerraTek, Inc. (Salt Lake City, UT), RE/SPEC, Inc. (Rapid City, SD), and Core Laboratories-Special Core Analysis Laboratory (Carrollton, TX) for Rock Physics Associates. In addition, this report contains the only WIPP-specific two-phase-flow capillary-pressure data for twelve core samples. The WIPP-specific data generated in this laboratory study and in WIPP field-test programs and information from suitable analogs will form the basis for specification of single- and two-phase flow parameters for anhydrite markers beds for WIPP performance assessment calculations

Sandstone Turning by Abrasive Waterjet

Czech Academy of Sciences Publication Activity Database

Hlaváček, Petr; Cárach, J.; Hloch, Sergej; Vasilko, K.; Klichová, Dagmar; Klich, Jiří; Lehocká, D.

2015-01-01

Roč. 48, č. 6 (2015), s. 2489-2493 ISSN 0723-2632 R&D Projects: GA MŠk ED2.1.00/03.0082; GA MŠk(CZ) LO1406 Institutional support: RVO:68145535 Keywords : turning away from the jet * conventional turning towards the jet * sandstone * abrasive water jet Subject RIV: JQ - Machines ; Tools Impact factor: 2.386, year: 2015 http://www.springerprofessional.de/sandstone-turning-by-abrasive-waterjet/6038028.html

Petrophysical study of Szolnok Formation, Endrod gas field,

Directory of Open Access Journals (Sweden)

Abdel Moktader A. El Sayed

2017-03-01

Full Text Available Results of both porosity and permeability can be used by geologists, petrophysicists, and petroleum engineers to evaluate reservoir rock, heterogeneity, and pore space history through the time of deposition and lithifaction. On the other hand, reservoir quality as well as reservoir classification could be performed based on these data correlation. The Szolnok Formation is composed mainly of turbidity elastic deposits while siltstones are intercalated by sandstone beds and streaks of marls. In the present study, 213 core samples are obtained from the Szolnok Formation of the Great Hungarian plain, Hungary. Both horizontal and vertical permeability are measured. The Szolnok Formation has two main lithologic groups: 1. clean sandstone (141 samples and 2. siltstone – marl (72 samples, it can easily differentiate between good, intermediate or even bad reservoirs. Acoustic laboratory measurements have been carried out for only 30 sandstone rock samples parallel to the bedding plane (horizontal. This paper aims to evaluate some petrophysical relationships. On the other hand, both Wyllie and Raymer models were applied for porosity estimation from seismic velocity. It is worthy to mention that reservoir diagnosis of the Szolnok Formation was our target as well. Both the porosity and permeability variation range characterizing the detected lithologic facies of the Szolnok Formation are useful for reservoir zonation. The relationship between helium and mercury porosity for whole studied samples and sandstone samples as well, are supported by a high correlation coefficient and allow its application for prediction of porosity while it reduces costs and time of laboratory measurements. The evaluation of different calculated equations for porosity from compressional wave velocity data of the Szolnok Formation are studied and the relationship between velocity and porosity displays a clear inverse trend. The comparison between laboratory porosity and sonic

Depositional environment of the Fort Member of the Jurasic Jaisalmer Formation (western Rajasthan, India), as revealed from lithofacies and grain-size analysis

International Nuclear Information System (INIS)

Ahmad, F.; Quasim, M.; Ghaznavi, A.; Khan, Z.; Ahmad, A.H.M.

2017-01-01

Lithofacies and granulometric analysis were carried out to decipher the depositional environment of the Fort Member of the Jurassic Jaisalmer Formation. Based on field data nine lithofacies have been identified including trough cross-bedded sandstones, planar cross-bedded sandstones, matrix supported conglomerates, thinly bedded siltstone and sandstones, herringbone cross-bedded sandstones, wave rippled sandstones, laminated sandstones, hummocky cross-bedded sandstones, limestones and shales. Granulometric analysis of the sandstones samples has been carried out for their statistical and textural parameters. Bivariant plots of textural parameters such as graphic skewness versus graphic standard deviation and kewness versus standard deviation confirm the high energy (beach) origin of sandstones. These results suggest a wide spectrum of marine environments ranging from inner shelf to upper shoreface for the Fort Member sandstones.

Regional distribution regularity of sandstone uranium deposits in Asian continent and prospecting strategy for sandstone uranium deposits in China

International Nuclear Information System (INIS)

Chen Zuyi

2002-01-01

Since the 1980's, after the discovery of numerous sandstone uranium deposits in Middle Asia (Kazakhstan, Uzbekistan) many large sandstone uranium deposits have been found in both Russia and Mongolia. So that Asia has become the most concentrated region of sandstone uranium deposits. The known sandstone uranium deposits occur mostly in a arcual tectonic belt constrained from the north by the Siberian continental block, and the Tarim-North China continental block from the south. This belt is named by Russian geologists as the Central Asian Mobile Belt, and some Chinese geologists call it the 'Mongolian Arc'. A lot of large and super large metallic, non-metallic, gold, polymetallic, porphyry copper and gold, massive sulphide and uranium deposits (of sandstone and volcanic types) with different origin and various types concentrated occur in this belt. The abundant and colourful mineral resources in the region are closely associated with the specific geologic-tectonic evolution of the above belt. It is necessary to strengthen the detailed geologic research and uranium prospecting in the region

Characterization and 3D reservoir modelling of fluvial sandstones of the Williams Fork Formation, Rulison Field, Piceance Basin, Colorado, USA

International Nuclear Information System (INIS)

Pranter, Matthew J; Vargas, Marielis F; Davis, Thomas L

2008-01-01

This study describes the stratigraphic characteristics and distribution of fluvial deposits of the Upper Cretaceous Williams Fork Formation in a portion of Rulison Field and addresses 3D geologic modelling of reservoir sand bodies and their associated connectivity. Fluvial deposits include isolated and stacked point-bar deposits, crevasse splays and overbank (floodplain) mudrock. Within the Williams Fork Formation, the distribution and connectivity of fluvial sandstones significantly impact reservoir productivity and ultimate recovery. The reservoir sandstones are primarily fluvial point-bar deposits interbedded with shales and coals. Because of the lenticular geometry and limited lateral extent of the reservoir sandstones (common apparent widths of ∼500–1000 ft; ∼150–300 m), relatively high well densities (e.g. 10 acre (660 ft; 200 m) spacing) are often required to deplete the reservoir. Heterogeneity of these fluvial deposits includes larger scale stratigraphic variability associated with vertical stacking patterns and structural heterogeneities associated with faults that exhibit lateral and reverse offsets. The discontinuous character of the fluvial sandstones and lack of distinct marker beds in the middle and upper parts of the Williams Fork Formation make correlation between wells tenuous, even at a 10 acre well spacing. Some intervals of thicker and amalgamated sandstones within the middle and upper Williams Fork Formation can be correlated across greater distances. To aid correlation and for 3D reservoir modelling, vertical lithology proportion curves were used to estimate stratigraphic trends and define the stratigraphic zonation within the reservoir interval. Object-based and indicator-based modelling methods have been applied to the same data and results from the models were compared. Results from the 3D modelling indicate that sandstone connectivity increases with net-to-gross ratio and, at lower net-to-gross ratios (<30%), differences exist in

Wettability Alteration of Sandstone and Carbonate Rocks by Using ZnO Nanoparticles in Heavy Oil Reservoirs

Directory of Open Access Journals (Sweden)

Masoumeh Tajmiri

2015-10-01

Full Text Available Efforts to enhance oil recovery through wettability alteration by nanoparticles have been attracted in recent years. However, many basic questions have been ambiguous up until now. Nanoparticles penetrate into pore volume of porous media, stick on the core surface, and by creating homogeneous water-wet area, cause to alter wettability. This work introduces the new concept of adding ZnO nanoparticles by an experimental work on wettability alteration and oil recovery through spontaneous imbibition mechanism. Laboratory tests were conducted in two experimental steps on four cylindrical core samples (three sandstones and one carbonate taken from a real Iranian heavy oil reservoir in Amott cell. In the first step, the core samples were saturated by crude oil. Next, the core samples were flooded with nanoparticles and saturated by crude oil for about two weeks. Then, the core samples were immersed in distilled water and the amount of recovery was monitored during 30 days for both steps. The experimental results showed that oil recovery for three sandstone cores changed from 20.74, 4.3, and 3.5% of original oil in place (OOIP in the absence of nanoparticles to 36.2, 17.57, and 20.68% of OOIP when nanoparticles were added respectively. Moreover, for the carbonate core, the recovery changed from zero to 8.89% of OOIP by adding nanoparticles. By the investigation of relative permeability curves, it was found that by adding ZnO nanoparticles, the crossover-point of curves shifted to the right for both sandstone and carbonate cores, which meant wettability was altered to water- wet. This study, for the first time, illustrated the remarkable role of ZnO nanoparticles in wettability alteration toward more water-wet for both sandstone and carbonate cores and enhancing oil recovery.

Discussion on the origin of bleached sandstone of Qianjiadian uranium deposit

International Nuclear Information System (INIS)

Pang Yaqing; Xiang Weidong; Li Tiangang; Chen Xiaolin; Xia Yuliang

2007-01-01

Qianjiadian uranium deposit is a sandstone-type uranium deposit that has been discovered in Songliao Basin in recent years. Uranium ore bodies are planar or lenticular in shape and under the control of the contact between gray sandstones and bleached sandstones. The bleached sandstone is white in color, cemented loosely, nearly without TOC and pyrite contained and rich in uranium. Geochemical characteristics and types and assemblages of clay minerals of the bleached sandstone reveal that the bleached sandstone is the product of oxidation of the interlayer oxidation zone, and it is a part of the interlayer oxidation zone. The main reasons for white color of the bleached sandstone are transfer of iron ion, oxidation of TOC and kaolinization of sandstone. (authors)

Predicting permeability and electrical conductivity of sedimentary rocks from microgeometry

International Nuclear Information System (INIS)

Schlueter, E.M.; Cook, N.G.W.

1991-02-01

The determination of hydrologic parameters that characterize fluid flow through rock masses on a large scale (e.g., hydraulic conductivity, capillary pressure, and relative permeability) is crucial to activities such as the planning and control of enhanced oil recovery operations, and the design of nuclear waste repositories. Hydraulic permeability and electrical conductivity of sedimentary rocks are predicted from the microscopic geometry of the pore space. The cross-sectional areas and perimeters of the individual pores are estimated from two-dimensional scanning electron micrographs of rock sections. The hydraulic and electrical conductivities of the individual pores are determined from these geometrical parameters, using Darcy's law and Ohm's law. Account is taken of the fact that the cross-sections are randomly oriented with respect to the channel axes, and for possible variation of cross-sectional area along the length of the pores. The effective medium theory from solid-state physics is then used to determine an effective average conductance of each pore. Finally, the pores are assumed to be arranged on a cubic lattice, which allows the calculation of overall macroscopic values for the permeability and the electrical conductivity. Preliminary results using Berea, Boise, Massilon and Saint-Gilles sandstones show reasonably close agreement between the predicted and measured transport properties. 12 refs., 5 figs., 1 tab

Nature, origin, and production characteristics of the Lower Silurian regional oil and gas accumulation, central Appalachian basin, United States

Science.gov (United States)

Ryder, R.; Zagorski, W.A.

2003-01-01

Low-permeability sandstones of the Lower Silurian regional oil and gas accumulation cover about 45,000 mi2 (117,000 km2) of the Appalachian basin and may contain as much as 30 tcf of recoverable gas resources. Major reservoirs consist of the "Clinton" sandstone and Medina Group sandstones. The stratigraphically equivalent Tuscarora Sandstone increases the area of the Lower Silurian regional accumulation (LSRA) by another 30,000 mi2 (78,000 km2). Approximately 8.7 tcf of gas and 400 million bbl of oil have been produced from the Clinton/Medina reservoirs since 1880. The eastern predominantly gas-bearing part of the LSRA is a basin-center gas accumulation, whereas the western part is a conventional oil and gas accumulation with hybrid features of a basin-center accumulation. The basin-center accumulations have pervasive gas saturation, water near irreducible saturation, and generally low fluid pressures. In contrast, the hybrid-conventional accumulations have less-pervasive oil and gas saturation, higher mobile-water saturation, and both normal and abnormally low fluid pressures. High mobile-water saturation in the hybrid-conventional reservoirs form the updip trap for the basin-center gas creating a broad transition zone, tens of miles wide, that has characteristics of both end-member accumulation types. Although the Tuscarora Sandstone part of the basin-center gas accumulation is pervasively saturated with gas, most of its constituent sandstone beds have low porosity and permeability. Commercial gas fields in the Tuscarora Sandstone are trapped in naturally fractured, faulted anticlines. The origin of the LSRA includes (1) generation of oil and gas from Ordovician black shales, (2) vertical migration through an overlying 1000-ft (305-m)-thick Ordovician shale; (3) abnormally high fluid pressure created by oil-to-gas transformation; (4) updip displacement of mobile pore water by overpressured gas; (5) entrapment of pervasive gas in the basin center; (6) postorogenic

New geochronologic and stratigraphic evidence confirms the paleocene age of the dinosaur-bearing ojo alamo sandstone and animas formation in the San Juan Basin, New Mexico and Colorado

Science.gov (United States)

Fassett, J.E.

2009-01-01

Dinosaur fossils are present in the Paleocene Ojo Alamo Sandstone and Animas Formation in the San Juan Basin, New Mexico, and Colorado. Evidence for the Paleo-cene age of the Ojo Alamo Sandstone includes palynologic and paleomagnetic data. Palynologic data indicate that the entire Ojo Alamo Sandstone, including the lower dinosaur-bearing part, is Paleocene in age. All of the palynomorph-productive rock samples collected from the Ojo Alamo Sandstone at multiple localities lacked Creta-ceous index palynomorphs (except for rare, reworked specimens) and produced Paleocene index palynomorphs. Paleocene palynomorphs have been identified strati-graphically below dinosaur fossils at two separate localities in the Ojo Alamo Sand-stone in the central and southern parts of the basin. The Animas Formation in the Colorado part of the basin also contains dinosaur fossils, and its Paleocene age has been established based on fossil leaves and palynology. Magnetostratigraphy provides independent evidence for the Paleocene age of the Ojo Alamo Sandstone and its dinosaur-bearing beds. Normal-polarity magnetochron C29n (early Paleocene) has been identified in the Ojo Alamo Sandstone at six localities in the southern part of the San Juan Basin. An assemblage of 34 skeletal elements from a single hadrosaur, found in the Ojo Alamo Sandstone in the southern San Juan Basin, provided conclusive evidence that this assemblage could not have been reworked from underlying Cretaceous strata. In addition, geochemical studies of 15 vertebrate bones from the Paleocene Ojo Alamo Sandstone and 15 bone samples from the underlying Kirtland Formation of Late Creta-ceous (Campanian) age show that each sample suite contained distinctly different abundances of uranium and rare-earth elements, indicating that the bones were miner-alized in place soon after burial, and that none of the Paleocene dinosaur bones ana-lyzed had been reworked. ?? U.S. Geological Survey, Public Domain April 2009.

The organic geochemistry characteristic simple analyse of Shihongtan sandstone-type uranium deposit in Turpan-Hami basin

International Nuclear Information System (INIS)

Qiao Haiming; Cai Jinfang; Shang Gaofeng; Song Zhe

2007-12-01

The Shihongtan uranium deposit in Turpan-Hami basin is an interlayer oxi- dized zone type sandstone uranium deposit. The deposit occurs in the coal-bear- ing detrital rocks of braided meandering steam facies in the Middle Jurassic Xishanyao formation. There is a great deal of organic matter in the ore-hosting bed. There is distinct content of organic carbon, soluble organic matter, acidolysis hydrocarbon in various geochemistry belt rock, and the maximum content in the ore belt. Organics carbon mother-material type is sapropelic humus, organic matter is under mature stage, Acidolysis hydrocarbon is coal-gas type. Uranium content in rock is positive correlativity to soluble organics and acidolysis hydrocarbon by statistical count, The role of organic matter in sandstone type uranium metallogenetic process is analysed, it is thought that material decomposed under oxygenic coalition is advantage to uranium dissolution and migration in groundwater, material decomposed and polymerized under oxygen-deficient condition forms reducing and adsorption geochemistry barrier for uranium precipitation, play a important role in uranium metallogenetic process. (authors)

Endothelial glycocalyx dysfunction in disease: albuminuria and increased microvascular permeability.

Science.gov (United States)

Salmon, Andrew H J; Satchell, Simon C

2012-03-01

Appreciation of the glomerular microcirculation as a specialized microcirculatory bed, rather than as an entirely separate entity, affords important insights into both glomerular and systemic microvascular pathophysiology. In this review we compare regulation of permeability in systemic and glomerular microcirculations, focusing particularly on the role of the endothelial glycocalyx, and consider the implications for disease processes. The luminal surface of vascular endothelium throughout the body is covered with endothelial glycocalyx, comprising surface-anchored proteoglycans, supplemented with adsorbed soluble proteoglycans, glycosaminoglycans and plasma constituents. In both continuous and fenestrated microvessels, this endothelial glycocalyx provides resistance to the transcapillary escape of water and macromolecules, acting as an integral component of the multilayered barrier provided by the walls of these microvessels (ie acting in concert with clefts or fenestrae across endothelial cell layers, basement membranes and pericytes). Dysfunction of any of these capillary wall components, including the endothelial glycocalyx, can disrupt normal microvascular permeability. Because of its ubiquitous nature, damage to the endothelial glycocalyx alters the permeability of multiple capillary beds: in the glomerulus this is clinically apparent as albuminuria. Generalized damage to the endothelial glycocalyx can therefore manifest as both albuminuria and increased systemic microvascular permeability. This triad of altered endothelial glycocalyx, albuminuria and increased systemic microvascular permeability occurs in a number of important diseases, such as diabetes, with accumulating evidence for a similar phenomenon in ischaemia-reperfusion injury and infectious disease. The detection of albuminuria therefore has implications for the function of the microcirculation as a whole. The importance of the endothelial glycocalyx for other aspects of vascular function

Sedimentary uranium occurrences in Eastern Europe with special reference to sandstone formations

International Nuclear Information System (INIS)

Barthel, F.; Hahn, L.

1985-01-01

Sedimentary uranium deposits, especially in sandstones, play an important role in uranium mining in Eastern Europe. The paper reviews recent publications on uranium occurrences in sandstone formations in the German Democratic Republic, Poland, CSSR, Hungary, Romania, Bulgaria and Albania. The uranium deposits in sandstones in Yugoslavia are described in a separate paper in this volume. Sandstone deposits of the USSR are not reviewed. Uranium mineralizations occur in sandstones from Ordovician to Tertiary age. Major deposits are developed in Upper Carboniferous sandstones in association with coal (GDR, Poland), in Permian strata (CSSR, Hungary, Romania), in Cretaceous sandstones (GDR, CSSR), and in Tertiary sediments (CSSR). The Permian deposits can be compared with deposits of similar age in Northern Italy and Northern Yugoslavia. Roll-type orebodies are developed in some of the Cenomanian sandstones. Tertiary deposits are mainly associated with lignites. Uranium deposits in sandstones of Albania and Bulgaria are not described in the literature. Geologic similarities with sandstone basins in adjacent countries suggest the presence of uranium mineralizations in Permian, Lower Triassic, and Tertiary sandstones. (author)

The depositional environment and petrology of the White Rim Sandstone Member of the Permian Cutler Formation, Canyonlands National Park, Utah

Science.gov (United States)

Steele-Mallory, B. A.

1982-01-01

The White Rim Sandstone Member of the Cutler Formation of Permian age in Canyonlands National Park, Utah, was deposited in coastal eolian and associated interdune environments. This conclusion is based on stratigraphic relationships primary sedimentary structures, and petrologic features. The White Rim consists of two major genetic units. The first represents a coastal dune field and the second represents related interdune ponds. Distinctive sedimentary structures of the coastal dune unit include large- to medium-scale, unidirectional, tabular-planar cross-bedding; high-index ripples oriented parallel to dip direction of the foresets; coarse-grained lag layers; avalanche or slump marks; and raindrop impressions. Cross-bedding measurements suggest the dunes were deposited as transverse ridges by a dominantly northwest to southeast wind. Distinctive sedimentary structures of the interdune pond unit include wavy, horizontally laminated bedding, adhesion ripples, and desiccation polygons. These features may have been produced by alternate wetting and drying of sediment during water-table fluctuations. Evidence of bioturbation is also present in this unit. Petrologic characteristics of the White Rim helped to define the depositional environment as coastal. A crinoid fragment was identified at one location; both units are enriched in heavy minerals, and small amounts of well rounded, reworked glauconite were found in the White Rim throughout the study area. Earlier work indicates that the White Rim sandstone is late Wolfcampian to early Leonardian in age. During this time, the Canyonlands area was located in a depositional area alternately dominated by marine and nonmarine environments. Results of this study suggest the White Rim represents a coastal dune field that was deposited by predominantly on-shore winds during a period of marine transgression.

Detrital zircon provenance of the Hartselle Sandstone Unit, Southeastern USA: Insights into sediment source, paleogeography, and setting

Science.gov (United States)

Harthy, M. A.; Gifford, J.

2017-12-01

The Hartselle sandstone is an excellent example of an Oil sand, a resource rich in bitumen. The unit is a light-colored thick-bedded to massive quartzose sandstone, that is widespread across an area from Georgia in the east to Mississippi in the west, and south from Alabama to Kentucky as a northern border. Formation thickness ranges from 0 to more than 150 feet. The unit has been stratigraphically dated to the Middle-Upper Mississippian age. One hypothesis suggests that the sandstone unit formed from the geological remains of barrier islands located in the ocean between Gondwana and Laurentia. The Hartselle is thought to have formed by the movement waves and currents along the shoreline, which carried sand and concentrated it into a set of northwest to southeast trending barrier islands. Transgression-regression events shifted the islands back and forth in relation to the position of the shoreline, leading to the large areal extent of the unit. However, the current data are not enough to explain the geographical position of the Hartselle sandstone unit as it is not running parallel to the ancient shoreline. Another mystery is the source of the sand, some believing the source was from the south (Gondwana) and others that erosion was from the north (Laurentia). Detrital zircon provenance analysis will address the uncertainty in sediment source. We will compare zircon U-Pb age spectra to possible Laurentian and Gondwanan source areas to discriminate between these possibilities. In addition, the age of the youngest detrital zircon population will provide additional constraints on the maximum age of deposition for the unit. These detrital ages will also help us to understand the tectonic setting at the time of Hartselle deposition. Lastly, we aim to explain the widespread nature of the unit and the processes involved in the formation of the Hartselle sandstone. When taken together, these interpretations will illuminate the age, depositional and tectonic setting of a

The sandstone's chromatic alteration of the florentine cultural heritage

Science.gov (United States)

Vettori, S.; Pecchioni, E.; Cantisani, E.; Ricci, M.; Fratini, F.; Garzonio, C. A.

2012-04-01

Pietra Serena is one of the materials more used in Florentine architecture. It is a sandstone that outcrops in the hills north of the city in the municipality of Fiesole and it has been employed mainly for ornamental purposes. This litotype belongs to the the Macigno Formation (Oligocene Upper- Miocene Lower) which consists of beds of turbiditic sandstones separated by pelitic levels which are the finest components of each single turbidity layer. Petrographically, Pietra Serena can be defined as a medium-coarse-grained greywacke made of quartz, feldspars, micas, fragments of metamorphic and magmatic rocks. The clayey matrix is quite abundant, mainly composed by illite, kaolinite and chlorite-vermiculite (present only in some quarries). It is well known that the processes of decay of the sandstones are related to the type of matrix, the amount of cement, the kind of clay minerals and to the pore size distribution, which lead to water infiltrations, swelling of the clay minerals, separation of the clayey matrix, with resulting exfoliation and peeling of the stone artefacts. Pietra Serena has a bluish-grey colour in fresh cut, but many times it is easily oxidized acquiring an ochraceous-reddish brown colour on buildings. Such changes in colour, appear to be due in part to the oxidation of iron, proceeding very quickly from the surface to the inside, though the cohesion is not affected. It is possible to hypothesize that the chromatic changes not necessarily involve a progressive state of alteration of the artefact, but they may often to represents a natural patina acquired with the time. Nevertheless it is necessary to remember that the oxidized layer and its hardness could also be the result of treatments performed in the past. In Florence, several monuments and buildings are affected by such phenomenon, in particular it is possible to note an intense and diffuse reddish colouring on the Pietra Serena utilized for columns and for façade's decorations. In this work

Hydrology of the Ferron sandstone aquifer and effects of proposed surface-coal mining in Castle Valley, Utah, with sections on stratigraphy and leaching of overburden

Science.gov (United States)

Lines, Gregory C.; Morrissey, Daniel J.; Ryer, Thomas A.; Fuller, Richard H.

1983-01-01

Coal in the Ferron Sandstone Member of the Mancos Shale of Cretaceous age has traditionally been mined by underground techniques in the Emery Coal Field in the southern end of Castle Valley in east-central Utah. However, approximately 99 million tons are recoverable by surface mining. Ground water in the Ferron is the sole source of supply for the town of Emery, but the aquifer is essentially untapped outside the Emery area.The Ferron Sandstone Member crops out along the eastern edge of Castle Valley and generally dips 2 ? to 10 ? to the northwest. Sandstones in the Ferron are enclosed between relatively impermeable shale in the Tununk and Blue Gate Members of the Mancos Shale. Along the outcrop, the Ferron ranges in thickness from about 80 feet in the northern part of Castle Valley to 850 feet in the southern part. The Ferron also generally thickens in the subsurface downdip from the outcrop. Records from wells and test holes indicate that the full thickness of the Ferron is saturated with water in most areas downdip from the outcrop area.Tests in the Emery area indicate that transmissivity of the Ferron sandstone aquifer ranges from about 200 to 700 feet squared per day where the Ferron is fully saturated. Aquifer transmissivity is greatest near the Paradise Valley-Joes Valley fault system where permeability has been increased by fracturing. Storage coefficient ranges from about 10 .6 to 10 -3 where the Ferron sandstone aquifer is confined and probably averages 5 x 10-2 where it is unconfined.

Geomechanics of bedded salt

International Nuclear Information System (INIS)

Serata, S.; Milnor, S.W.

1979-01-01

Creep data from the literature search is reinterpreted by SGI, resulting in a better understanding of the temperature and stress state dependence of the octahedral creep rate and the octahedral shear strength. The concept of a transition strength between the elastic and the plastic states is in agreement with the data. The elastic and rheological properties of salt are described, and a set of constitutive equations is presented. The dependence of material properties on parameters such as temperature is considered. Findings on the permeability of salt are summarized, and the in-situ behavior of openings in bedded salt is described based on extensive engineering experience. A stress measuring system utilizing a finite element computer code is discussed. Geological factors affecting the stability of salt openings are considered, and the Stress Control Technique for designing stable openings in bedded salt formations is explained

Porosity, single-phase permeability, and capillary pressure data from preliminary laboratory experiments on selected samples from Marker Bed 139 at the Waste Isolation Pilot Plant. Volume 3 of 3: Appendices C, D, E, and F

Energy Technology Data Exchange (ETDEWEB)

Howarth, S.M.; Christian-Frear, T.

1997-08-01

This volume contains the mineralogy, porosity, and permeability results from the Marker Bed 139 anhydrite specimens evaluated by TerraTek, Inc. for the Waste Isolation Pilot Plant. This volume also documents the brine recipe used by RE/SPEC, Inc., the parameter package submitted to Performance Assessment based on all the data, and a memo on the mixed Brooks and Corey two-phase characteristic curves.

Porosity, single-phase permeability, and capillary pressure data from preliminary laboratory experiments on selected samples from Marker Bed 139 at the Waste Isolation Pilot Plant. Volume 3 of 3: Appendices C, D, E, and F

International Nuclear Information System (INIS)

Howarth, S.M.; Christian-Frear, T.

1997-08-01

This volume contains the mineralogy, porosity, and permeability results from the Marker Bed 139 anhydrite specimens evaluated by TerraTek, Inc. for the Waste Isolation Pilot Plant. This volume also documents the brine recipe used by RE/SPEC, Inc., the parameter package submitted to Performance Assessment based on all the data, and a memo on the mixed Brooks and Corey two-phase characteristic curves

57Fe Mössbauer and X-ray characterisation of sandstones

International Nuclear Information System (INIS)

Mulaba-Bafubiandi, A. F.; Waanders, F. B.

2013-01-01

Sandstones from the Free State province in South Africa have been mined and processed mainly by small scale and artisanal miners in the rural areas. In the present investigation basic fire proof and water absorption tests, X-ray and γ-ray based characterisation techniques were used to study the sandstones. The collected samples were grouped according to their apparent colour in day light conditions and the elemental analysis showed the presence of a high amount of oxygen (>52%) and silicon (>38%) with Mn, Al, Fe and Ca as major elements in proportions related to the colour distribution of the various sandstones. The uniaxial compressive stress was found to be the highest (56 MPa) for the greyish sandstone and the lowest (8 MPa) for the white sandstone sample, also associated with the lowest (Al+Fe)/Si value of 0.082. The humidity test showed that the 6 % water absorption was lower than the recommended ASTM value of 8 %. The sandstone samples were also subjected to various high temperatures to simulate possible fire conditions and it was found that the non alteration of the mineral species might be one of the reasons why the sandstones are regarded as the most refractory amongst the building materials typically used. Mössbauer spectroscopy revealed that iron is present in all the sandstones, mainly as Fe 3 +  with the black sandstone showing an additional presence of 3 % Fe 2 +  indicating that a higher iron content coupled to higher silicon content, contributes to an increase in the uniaxial compressive strength.

Implications of heterogeneous fracture distribution on reservoir quality; an analogue from the Torridon Group sandstone, Moine Thrust Belt, NW Scotland

Science.gov (United States)

Watkins, Hannah; Healy, David; Bond, Clare E.; Butler, Robert W. H.

2018-03-01

Understanding fracture network variation is fundamental in characterising fractured reservoirs. Simple relationships between fractures, stress and strain are commonly assumed in fold-thrust structures, inferring relatively homogeneous fracture patterns. In reality fractures are more complex, commonly appearing as heterogeneous networks at outcrop. We use the Achnashellach Culmination (NW Scotland) as an outcrop analogue to a folded tight sandstone reservoir in a thrust belt. We present fracture data is collected from four fold-thrust structures to determine how fracture connectivity, orientation, permeability anisotropy and fill vary at different structural positions. We use a 3D model of the field area, constructed using field observations and bedding data, and geomechanically restored using Move software, to determine how factors such as fold curvature and strain influence fracture variation. Fracture patterns in the Torridon Group are consistent and predictable in high strain forelimbs, however in low strain backlimbs fracture patterns are inconsistent. Heterogeneities in fracture connectivity and orientation in low strain regions do not correspond to fluctuations in strain or fold curvature. We infer that where strain is low, other factors such as lithology have a greater control on fracture formation. Despite unpredictable fracture attributes in low strain regions, fractured reservoir quality would be highest here because fractures in high strain forelimbs are infilled with quartz. Heterogeneities in fracture attribute data on fold backlimbs mean that fractured reservoir quality and reservoir potential is difficult to predict.

Petrography and geochemistry of Jurassic sandstones from the ...

Indian Academy of Sciences (India)

V Periasamy

On the basis of geochemical results, sandstones are classified into arkose, ..... Geochemical classification diagram of sandstone samples from the Jhuran Formation based on log(SiO2/Al2O3)– ..... 1993) showing single trend for the Jhuran.

Characterization of the Oriskany and Berea Sandstones: Evaluating Biogeochemical Reactions of Potential Sandstone–Hydraulic Fracturing Fluid Interaction

Energy Technology Data Exchange (ETDEWEB)

Verba, Circe [National Energy Technology Lab. (NETL), Albany, OR (United States); Harris, Aubrey [National Energy Technology Lab. (NETL), Albany, OR (United States)

2016-07-07

The Marcellus shale, located in the mid-Atlantic Appalachian Basin, has been identified as a source for natural gas and targeted for hydraulic fracturing recovery methods. Hydraulic fracturing is a technique used by the oil and gas industry to access petroleum reserves in geologic formations that cannot be accessed with conventional drilling techniques (Capo et al., 2014). This unconventional technique fractures rock formations that have low permeability by pumping pressurized hydraulic fracturing fluids into the subsurface. Although the major components of hydraulic fracturing fluid are water and sand, chemicals, such as recalcitrant biocides and polyacrylamide, are also used (Frac Focus, 2015). There is domestic concern that the chemicals could reach groundwater or surface water during transport, storage, or the fracturing process (Chapman et al., 2012). In the event of a surface spill, understanding the natural attenuation of the chemicals in hydraulic fracturing fluid, as well as the physical and chemical properties of the aquifers surrounding the spill site, will help mitigate potential dangers to drinking water. However, reports on the degradation pathways of these chemicals are limited in existing literature. The Appalachian Basin Marcellus shale and its surrounding sandstones host diverse mineralogical suites. During the hydraulic fracturing process, the hydraulic fracturing fluids come into contact with variable mineral compositions. The reactions between the fracturing fluid chemicals and the minerals are very diverse. This report: 1) describes common minerals (e.g. quartz, clay, pyrite, and carbonates) present in the Marcellus shale, as well as the Oriskany and Berea sandstones, which are located stratigraphically below and above the Marcellus shale; 2) summarizes the existing literature of the degradation pathways for common hydraulic fracturing fluid chemicals [polyacrylamide, ethylene glycol, poly(diallyldimethylammonium chloride), glutaraldehyde

Sensing, Measuring and Modelling the Mechanical Properties of Sandstone

Science.gov (United States)

Antony, S. J.; Olugbenga, A.; Ozerkan, N. G.

2018-02-01

We present a hybrid framework for simulating the strength and dilation characteristics of sandstone. Where possible, the grain-scale properties of sandstone are evaluated experimentally in detail. Also, using photo-stress analysis, we sense the deviator stress (/strain) distribution at the micro-scale and its components along the orthogonal directions on the surface of a V-notch sandstone sample under mechanical loading. Based on this measurement and applying a grain-scale model, the optical anisotropy index K 0 is inferred at the grain scale. This correlated well with the grain contact stiffness ratio K evaluated using ultrasound sensors independently. Thereafter, in addition to other experimentally characterised structural and grain-scale properties of sandstone, K is fed as an input into the discrete element modelling of fracture strength and dilation of the sandstone samples. Physical bulk-scale experiments are also conducted to evaluate the load-displacement relation, dilation and bulk fracture strength characteristics of sandstone samples under compression and shear. A good level of agreement is obtained between the results of the simulations and experiments. The current generic framework could be applied to understand the internal and bulk mechanical properties of such complex opaque and heterogeneous materials more realistically in future.

Fundamental research on sintering technology with super deep bed achieving energy saving and reduction of emissions

International Nuclear Information System (INIS)

Hongliang Han; Shengli Wu; Gensheng Feng; Luowen Ma; Weizhong Jiang

2012-01-01

In the general frame of energy saving, environment protection and the concept of circular economy, the fundamental research on the sintering technology with super deep bed, achieving energy saving and emission reduction, was carried out. At first, the characteristics of the process and exhaust emission in the sintering with super deep bed was mastered through the study of the influence of different bed depths on the sintering process. Then, considering the bed permeability and the fuel combustion, their influence on the sinter yield and quality, their potential for energy saving and emission reduction was studied. The results show that the improvement of the bed permeability and of the fuel combustibility respectively and simultaneously, leads to an improvement of the sintering technical indices, to energy saving and emission reduction in the condition of super deep bed. At 1000 mm bed depth, and taking the appropriate countermeasure, it is possible to decrease the solid fuel consumption and the emission of CO 2 , SO 2 , NO x by 10.08%, 11.20%, 22.62% and 25.86% respectively; and at 700 mm bed depth, it is possible to reduce the solid fuel consumption and the emission of CO 2 , SO 2 , NO x by 20.71%, 22.01%, 58.86% and 13.13% respectively. This research provides the theoretical and technical basis for the new technology of sintering with super deep bed, achieving energy saving and reduction of emission. (authors)

Elevated Uranium in Aquifers of the Jacobsville Sandstone

Science.gov (United States)

Sherman, H.; Gierke, J.

2003-12-01

The EPA has announced a new standard for uranium in drinking water of 30 parts per billion (ppb). This maximum contaminant level (MCL) takes effect for community water supplies December 2003. The EPA's ruling has heightened awareness among residential well owners that uranium in drinking water may increase the risk of kidney disease and cancer and has created a need for a quantified, scientific understanding of the occurrence and distribution of uranium isotopes in aquifers. The authors are investigating the occurrence of elevated uranium in northern Michigan aquifers of the Middle Proterozoic Jacobsville sandstone, a red to mottled sequence of sandstones, conglomerates, siltstones and shales deposited as basin fill in the 1.1 Ga Midcontinent rift. Approximately 25% of 300 well water samples tested for isotopic uranium have concentrations above the MCL. Elevated uranium occurrences are distributed throughout the Jacobsville sandstone aquifers stretching across Michigan's Upper Peninsula. However, there is significant variation in well water uranium concentrations (from 0.01 to 190 ppb) and neighboring wells do not necessarily have similar concentrations. The authors are investigating hydrogeologic controls on ground water uranium concentrations in the Jacobsville sandstone, e.g. variations in lithology, mineralogy, groundwater residence time and geochemistry. Approximately 2000' of Jacobsville core from the Amoco St. Amour well was examined in conjunction with the spectral gamma ray log run in the borehole. Spikes in equivalent uranium (eU) concentration from the log are frequently associated with clay and heavy mineral layers in the sandstone core. The lithology and mineralogy of these layers will be determined by analysis of thin sections and x-ray diffraction. A portable spectrometer, model GRS-2000/BL, will be used on the sandstone cliffs along Lake Superior to characterize depositional and lithologic facies of the Jacobsville sandstone in terms of

Diagenesis and reservoir quality of Bhuban sandstones (Neogene), Titas Gas Field, Bengal Basin, Bangladesh

Science.gov (United States)

Aminul Islam, M.

2009-06-01

This study deals with the diagenesis and reservoir quality of sandstones of the Bhuban Formation located at the Titas Gas Field of Bengal Basin. Petrographic study including XRD, CL, SEM and BSE image analysis and quantitative determination of reservoir properties were carried out for this study. The sandstones are fine to medium-grained, moderately well to well sorted subfeldspathic arenites with subordinate feldspathic and lithic arenites. The diagenetic processes include clay infiltration, compaction and cementation (quartz overgrowth, chlorite, kaolinite, calcite and minor amount of pyrite, dolomite and K-feldspar overgrowth). Quartz is the dominant pore occluding cement and generally occurred as small euhedral crystals, locally as large pyramidal crystals in the primary pores. Pressure solution derived from grain contact is the main contributor of quartz overgrowths. Chlorite occurs as pore-lining and pore filling cement. In some cases, chlorite helps to retain porosity by preventing quartz overgrowth. In some restricted depth interval, pore-occlusion by calcite cement is very much intense. Kaolinite locally developed as vermiform and accelerated the minor porosity loss due to pore-occlusion. Kaolinite/chlorite enhances ineffective microporosity. Kaolinite is a by-product of feldspar leaching in the presence of acidic fluid produced during the maturation of organic matter in the adjacent Miocene or deeper Oligocene source rocks. The relation between diagenesis and reservoir quality is as follows: the initial porosity was decreased by compaction and cementation and then increased by leaching of the metastable grains and dissolution of cement. Good quality reservoir rocks were deposited in fluvial environment and hence quality of reservoir rocks is also environment selective. Porosity and permeability data exhibit good inverse correlation with cement. However, some data points indicate multiple controls on permeability. Reservoir quality is thus controlled by

Study of damages caused by drill fluids in sandstone samples using energy dispersive X-ray fluorescence (EDXRF); Estudo dos danos causados por fluido de perfuracao em amostras de arenito utilizando a fluorescencia de raios X dispersiva em energia (EDXRF)

Energy Technology Data Exchange (ETDEWEB)

Ribeiro, Joao Luiz B.; Lopes, Ricardo T.; Anjos, Marcelino J. dos; Leite, Jaques C. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia. Lab. de Instrumentacao Nuclear; Queiroz Neto, Joao C. [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

2002-07-01

The performance of an X ray fluorescence (EDXRF) system was evaluated for the determination of solids invasion profile. The EDXRF was used to identify the elements, that are present in the rock core after the damage tests. Results are presented of an experimental study of formation permeability damage caused by invasion of the inert and extraneous solids simulated by CaCO{sub 3} particles. Laboratory damage tests were performed using two types of sandstones core. Vila Velha, low permeability (15 mD) and Rio Bonito, high permeability (800 mD). The damage tests were performed with utilization of SIRF-P, which simulates the conditions find in-situ (petroleum well). (author)

Micropore Structure Representation of Sandstone in Petroleum Reservoirs Using an Atomic Force Microscope

International Nuclear Information System (INIS)

Bai Yong-Qiang; Zhu Xing; Wu Jun-Zheng; Bai Wen-Guang

2011-01-01

The pore structure of sandstone in an oil reservoir is investigated using atomic force microscopy (AFM). At nanoscale resolution, AFM images of sandstone show us the fine structure. The real height data of images display the three-dimensional space structure of sandstone effectively. The three-dimensional analysis results show that the AFM images of sandstone have unique characteristics that, like fingerprints, can identify different structural properties of sandstones. The results demonstrate that AFM is an effective method used to represent original sandstone in petroleum reservoirs, and may help geologists to appreciate the sandstone in oil reservoirs fully. (general)

Transport of silver nanoparticles in single fractured sandstone

Science.gov (United States)

Neukum, Christoph

2018-02-01

Silver nanoparticles (Ag-NP) are used in various consumer products and are one of the most prevalent metallic nanoparticle in commodities and are released into the environment. Transport behavior of Ag-NP in groundwater is one important aspect for the assessment of environmental impact and protection of drinking water resources in particular. Ag-NP transport processes in saturated single-fractured sandstones using triaxial flow cell experiments with different kind of sandstones is investigated. Ag-NP concentration and size are analyzed using flow field-flow fractionation and coupled SEM-EDX analysis. Results indicate that Ag-NP are more mobile and show generally lower attachment on rock surface compared to experiments in undisturbed sandstone matrix and partially fractured sandstones. Ag-NP transport is controlled by the characteristics of matrix porosity, time depending blocking of attachment sites and solute chemistry. Where Ag-NP attachment occur, it is heterogeneously distributed on the fracture surface.

Stormwater infiltration and surface runoff pollution reduction performance of permeable pavement layers.

Science.gov (United States)

Niu, Zhi-Guang; Lv, Zhi-Wei; Zhang, Ying; Cui, Zhen-Zhen

2016-02-01

In this paper, the laboratory-scale permeable pavement layers, including a surface permeable brick layer, coarse sand bedding layers (thicknesses = 2, 3.5, and 5 cm), and single-graded gravel sub-base layers (thicknesses = 15, 20, 25, and 30 cm), were built to evaluate stormwater infiltration and surface runoff pollution reduction performance. And, the infiltration rate (I) and concentrations of suspended solids (SS), total phosphorus (TP), chemical oxygen demand (COD), ammonia nitrogen, and total nitrogen (TN) were measured under the simulated rainfall intensity of 72.4 mm/h over duration of 60 min. The results indicate that the thickness factor primarily influences the infiltration rate and pollutant removal rate. The highest steady infiltration rate was for surface brick layer 51.0 mm/h, for 5-cm sand bedding layer 32.3 mm/h, and for 30-cm gravel sub-base layer 42.3 mm/h, respectively. The SS average removal rate was relative higher (79.8 ∼ 98.6 %) for all layers due to the interception and filtration. The average removal rates of TP and COD were for surface layer 71.2 and 24.1 %, for 5-cm bedding layer 54.8 and 9.0 %, and for 20-cm sub-base layer 72.2 and 26.1 %. Ammonia nitrogen and TN cannot steadily be removed by layers according to the experiment results. The optimal thickness of bedding sands was 5 cm, and that of sub-base gravels was 20 ∼ 30 cm.

Distal alluvial fan sediments in early Proterozoic red beds of the Wilgerivier formation, Waterberg Group, South Africa

Science.gov (United States)

Van Der Neut, M.; Eriksson, P. G.; Callaghan, C. C.

The 1900 - 1700 M.a. Waterberg Group belongs to a series of southern African cratonic cover sequences of roughly equivalent age. Red beds of the Wilgerivier Formation comprise sandstones, interbedded with subordinate conglomerates and minor mudrocks. These immature sedimentary rocks exhibit lenticular bedding, radial palaeocurrent patterns and features indicative of both streamflow and gravity-flow deposition. A distal wet alluvial fan palaeoenvironmental setting is envisaged, with fan-deltas forming where alluvial lobes prograded into a lacustrine basin. Intrastratal, diagenetic alteration of ferromagnesian detrital grains and ferruginous grain coatings led to the red colouration of the Wilgerivier sediments.

Study on Erosion Factors Affecting Kuroboku Soil Loss I. Water Permeability of Stratified Soil and Slope Gradient

OpenAIRE

田熊, 勝利; 猪迫, 耕二; 中原　恒,

2005-01-01

The authors examined the factors of bed soil affecting the loss of surface soil and the effects of these factors on the extent of the soil loss. They conducted a multivariate analysis using actual measurement value at a laboratory erosion experiment. They also conducted a simulation of erosion in soil loss using the bed soil factors. Soil loss quantity is dependent on the coefficient of permeability of bed soil; the steeper the latter is, the more the former increases. Lateral soil scattering...

DEVELOPMENT OF A METHODOLOGY FOR REGIONAL EVALUATION OF CONFINING BED INTEGRITY

Science.gov (United States)

For safe underground injection of liquid waste, confining formations must be thick, extensive, and have low permeability. Recognition of faults that extend from the potential injection zone to underground sources of drinking water is critical for evaluation of confining-bed integ...

Petrology and geochemistry of samples from bed-contact zones in Tunnel Bed 5, U12g-Tunnel, Nevada Test Site

International Nuclear Information System (INIS)

Connolly, J.R.; Keil, K.; Mansker, W.L.; Allen, C.C.; Husler, J.; Lowy, R.; Fortney, D.R.; Lappin, A.R.

1984-10-01

This report summarizes the detailed geologic characterization of samples of bed-contact zones and surrounding nonwelded bedded tuffs, both within Tunnel Bed 5, that are exposed in the G-Tunnel complex beneath Rainier Mesa on the Nevada Test Site (NTS). Original planning studies treated the bed-contact zones in Tunnel Bed 5 as simple planar surfaces of relatively high permeability. Detailed characterization, however, indicates that these zones have a finite thickness, are depositional in origin, vary considerably over short vertical and horizontal distances, and are internally complex. Fluid flow in a sequence of nonwelded zeolitized ash-flow or bedded tuffs and thin intervening reworked zones appears to be a porous-medium phenomenon, regardless of the presence of layering. There are no consistent differences in either bulk composition or detailed mineralogy between bedded tuffs and bed-contact zones in Tunnel Bed 5. Although the original bulk composition of Tunnel Bed 5 was probably peralkaline, extensive zeolitization has resulted in a present peraluminous bulk composition of both bedded tuffs and bed-contact zones. The major zeolite present, clinoptilolite, is intermediate (Ca:K:Na = 26:35:39) and effectively uniform in composition. This composition is similar to that of clinoptilolite from the tuffaceous beds of Calico Hills above the static water level in hole USW G-1, but somewhat different from that reported for zeolites from below the static water level in USW G-2. Tunnel Bed 5 also contains abundant hydrous manganese oxides. The similarity in composition of the clinoptilolites from Tunnel Bed 5 and those above the static water level at Yucca Mountain indicates that many of the results of nuclide-migration experiments in Tunnel Bed 5 would be transferrable to zeolitized nonwelded tuffs above the static water level at Yucca Mountain

Permeability in fractured rocks from deep geothermal boreholes in the Upper Rhine Graben

Science.gov (United States)

Vidal, Jeanne; Whitechurch, Hubert; Genter, Albert; Schmittbuhl, Jean; Baujard, Clément

2015-04-01

Permeability in fractured rocks from deep geothermal boreholes in the Upper Rhine Graben Vidal J.1, Whitechurch H.1, Genter A.2, Schmittbuhl J.1, Baujard C.2 1 EOST, Université de Strasbourg 2 ES-Géothermie, Strasbourg The thermal regime of the Upper Rhine Graben (URG) is characterized by a series of geothermal anomalies on its French part near Soultz-sous-Forêts, Rittershoffen and in the surrounding area of Strasbourg. Sedimentary formations of these areas host oil field widely exploited in the past which exhibit exceptionally high temperature gradients. Thus, geothermal anomalies are superimposed to the oil fields which are interpreted as natural brine advection occurring inside a nearly vertical multi-scale fracture system cross-cutting both deep-seated Triassic sediments and Paleozoic crystalline basement. The sediments-basement interface is therefore very challenging for geothermal industry because most of the geothermal resource is trapped there within natural fractures. Several deep geothermal projects exploit local geothermal energy to use the heat or produce electricity and thus target permeable fractured rocks at this interface. In 1980, a geothermal exploration well was drilled close to Strasbourg down to the Permian sediments at 3220 m depth. Bottom hole temperature was estimated to 148°C but the natural flow rate was too low for an economic profitability (geothermal site by drilling five boreholes, three of which extend to 5 km depth. They identified a temperature of 200° C at 5 km depth in the granitic basement but with a variable flow rate. Hydraulic and chemical stimulation operations were applied in order to increase the initial low permeability by reactivating and dissolving sealed fractures in basement. The productivity was considerably improved and allows geothermal exploitation at 165° C and 20 L/s. Recent studies revealed the occurrences of permeable fractures in the limestones of Muschelkalk and the sandstones of Buntsandstein also. For

INAA and petrological study of sandstones from the Angkor monuments

International Nuclear Information System (INIS)

Kucera, J.; Kranda, K.; Soukal, L.; Novak, J.K.; Lang, M.; Poncar, J.; Krausova, I.; Cunin, O.

2008-01-01

We determined 35 major, minor and trace elements in sandstone samples taken from building blocks of 19 Angkor temples and from an old and a new quarry using INAA. We also characterized the sandstone samples with conventional microscopy and electron microprobe analysis. Using cluster analysis, we found no straightforward correlation between the chemical/petrological properties of the sandstones and a presumed period of individual temples construction. The poor correlation may result either from the inherent inhomogeneity of sandstone or just reflect the diversity of quarries that supplied building blocks for the construction of any particular temple. (author)

Channel sandstone and bar morphology of the Beaufort group uranium district near Beaufort West

International Nuclear Information System (INIS)

Stear, W.M.

1980-01-01

Sheet-like and lenticular sandstone bodies in the Lower Beaufort Group (Adelaide Subgroup) uranium district occur in megacyclic repetition as superimposed systems of ephemeral fluvial channels that display characteristics of complex lateral and vertical accretion. Channel sandstone bodies are defined on morphological grounds into two types. Sheet sandstone bodies are the commonest type and comprise the bulk of sandstone packages in arenaceous zones of megacycles. Composite sandstone sheets result from multilateral coalescence of individual sandstone bodies. Isolated lenticular sandstone units in argillaceous zones of megacycles comprise sheet and ribbon sandstone types. Multi-storeying is a prominent feature of most channel sandstone bodies and often results in local sandstone thickening. Bedforms relate to the formation of compound bars and record periods of dynamic accretion and erosion. Rarely preserved palaeosurfaces vividly illustrate the fluctuating hydrodynamic conditions that typified ephemeral fluvial sedimentation in a semi-arid environment during Lower Beaufort times

Channel sandstone and bar morphology of the Beaufort group uranium district near Beaufort West

Energy Technology Data Exchange (ETDEWEB)

Stear, W M

1980-01-01

Sheet-like and lenticular sandstone bodies in the Lower Beaufort Group (Adelaide Subgroup) uranium district occur in megacyclic repetition as superimposed systems of ephemeral fluvial channels that display characteristics of complex lateral and vertical accretion. Channel sandstone bodies are defined on morphological grounds into two types. Sheet sandstone bodies are the commonest type and comprise the bulk of sandstone packages in arenaceous zones of megacycles. Composite sandstone sheets result from multilateral coalescence of individual sandstone bodies. Isolated lenticular sandstone units in argillaceous zones of megacycles comprise sheet and ribbon sandstone types. Multi-storeying is a prominent feature of most channel sandstone bodies and often results in local sandstone thickening. Bedforms relate to the formation of compound bars and record periods of dynamic accretion and erosion. Rarely preserved palaeosurfaces vividly illustrate the fluctuating hydrodynamic conditions that typified ephemeral fluvial sedimentation in a semi-arid environment during Lower Beaufort times.

The Importance of Splat Events to the Spatiotemporal Structure of Near-Bed Fluid Velocity and Bed Load Motion Over Bed Forms: Laboratory Experiments Downstream of a Backward Facing Step

Science.gov (United States)

Leary, K. C. P.; Schmeeckle, M. W.

2017-12-01

Flow separation/reattachment on the lee side of alluvial bed forms is known to produce a complex turbulence field, but the spatiotemporal details of the associated patterns of bed load sediment transported remain largely unknown. Here we report turbulence-resolving, simultaneous measurements of bed load motion and near-bed fluid velocity downstream of a backward facing step in a laboratory flume. Two synchronized high-speed video cameras simultaneously observed bed load motion and the motion of neutrally buoyant particles in a laser light sheet 6 mm above the bed at 250 frames/s downstream of a 3.8 cm backward facing step. Particle Imaging Velocimetry (PIV) and Acoustic Doppler Velocimetry (ADV) were used to characterize fluid turbulent patterns, while manual particle tracking techniques were used to characterize bed load transport. Octant analysis, conducted using ADV data, coupled with Markovian sequence probability analysis highlights differences in the flow near reattachment versus farther downstream. Near reattachment, three distinct flow patterns are apparent. Farther downstream we see the development of a dominant flow sequence. Localized, intermittent, high-magnitude transport events are more apparent near flow reattachment. These events are composed of streamwise and cross-stream fluxes of comparable magnitudes. Transport pattern and fluid velocity data are consistent with the existence of permeable "splat events," wherein a volume of fluid moves toward and impinges on the bed (sweep) causing a radial movement of fluid in all directions around the point of impingement (outward interaction). This is congruent with flow patterns, identified with octant analysis, proximal to flow reattachment.

Three-dimensional characterization of microporosity and permeability in fault zones hosted in heterolithic succession

Science.gov (United States)

Riegel, H. B.; Zambrano, M.; Jablonska, D.; Emanuele, T.; Agosta, F.; Mattioni, L.; Rustichelli, A.

2017-12-01

The hydraulic properties of fault zones depend upon the individual contributions of the damage zone and the fault core. In the case of the damage zone, it is generally characterized by means of fracture analysis and modelling implementing multiple approaches, for instance the discrete fracture network model, the continuum model, and the channel network model. Conversely, the fault core is more difficult to characterize because it is normally composed of fine grain material generated by friction and wear. If the dimensions of the fault core allows it, the porosity and permeability are normally studied by means of laboratory analysis or in the other case by two dimensional microporosity analysis and in situ measurements of permeability (e.g. micro-permeameter). In this study, a combined approach consisting of fracture modeling, three-dimensional microporosity analysis, and computational fluid dynamics was applied to characterize the hydraulic properties of fault zones. The studied fault zones crosscut a well-cemented heterolithic succession (sandstone and mudstones) and may vary in terms of fault core thickness and composition, fracture properties, kinematics (normal or strike-slip), and displacement. These characteristics produce various splay and fault core behavior. The alternation of sandstone and mudstone layers is responsible for the concurrent occurrence of brittle (fractures) and ductile (clay smearing) deformation. When these alternating layers are faulted, they produce corresponding fault cores which act as conduits or barriers for fluid migration. When analyzing damage zones, accurate field and data acquisition and stochastic modeling was used to determine the hydraulic properties of the rock volume, in relation to the surrounding, undamaged host rock. In the fault cores, the three-dimensional pore network quantitative analysis based on X-ray microtomography images includes porosity, pore connectivity, and specific surface area. In addition, images were

Numerical Simulation of Hydraulic Fracturing in Low-/High-Permeability, Quasi-Brittle and Heterogeneous Rocks

Science.gov (United States)

Pakzad, R.; Wang, S. Y.; Sloan, S. W.

2018-04-01

In this study, an elastic-brittle-damage constitutive model was incorporated into the coupled fluid/solid analysis of ABAQUS to iteratively calculate the equilibrium effective stress of Biot's theory of consolidation. The Young's modulus, strength and permeability parameter of the material were randomly assigned to the representative volume elements of finite element models following the Weibull distribution function. The hydraulic conductivity of elements was associated with their hydrostatic effective stress and damage level. The steady-state permeability test results for sandstone specimens under different triaxial loading conditions were reproduced by employing the same set of material parameters in coupled transient flow/stress analyses of plane-strain models, thereby indicating the reliability of the numerical model. The influence of heterogeneity on the failure response and the absolute permeability was investigated, and the post-peak permeability was found to decrease with the heterogeneity level in the coupled analysis with transient flow. The proposed model was applied to the plane-strain simulation of the fluid pressurization of a cavity within a large-scale block under different conditions. Regardless of the heterogeneity level, the hydraulically driven fractures propagated perpendicular to the minimum principal far-field stress direction for high-permeability models under anisotropic far-field stress conditions. Scattered damage elements appeared in the models with higher degrees of heterogeneity. The partially saturated areas around propagating fractures were simulated by relating the saturation degree to the negative pore pressure in low-permeability blocks under high pressure. By replicating previously reported trends in the fracture initiation and breakdown pressure for different pressurization rates and hydraulic conductivities, the results showed that the proposed model for hydraulic fracture problems is reliable for a wide range of

Distinguishing of uranium-bearing sandstone by the geochemical characteristics in northern Sichuan

International Nuclear Information System (INIS)

Wang Wangzhang; Zhang Zhufeng; Wang Yunliang; Sun Shuqin.

1994-01-01

Expounding geochemical characteristics of sandstone-type uranium deposits in northern Sichuan, the authors demonstrate the favourable and unfavourable conditions for enrichment of uranium on the basis of element abundances and ratios of U, Th and K measured by the gamma-ray spectroscopy surveying. The differences between uranium-bearing and non-uranium sandstones and between red sandstone (clay stone) and greenish sandstone can be determined by the gamma-ray spectroscopy (measuring U, Th and K) and XRF analysis (measuring As and Ba). Therefore, the prospecting of the sandstone-type uranium deposits in northern Sichuan can be concentrated in a certain range

Distribution characteristics of Shihongtan uranium deposits calcareous sandstone and discussion on their genesis

International Nuclear Information System (INIS)

Zhu Huanqiao; Jia Heng; Xu Gaozhong; Li Zhanyou

2007-12-01

It is considered that the calcareous sandstone appear at layer along of a bunch of pear lens on and off, localled near up and down surface of sandbody or washed surface, has sandstone of more macro-grain and more gradation through statistics and analysis of calcareous sandstone in goal layer in Shihongtan uranium deposits. The calcareous sandstone accumulation thickness chorogram demonstrated that the calcareous sandstone centralized distribution in the ore body growth area, thus it can be seen, in the oxidation reduction intermediate belt the calcareous sandstone forms with the uranium mine has the certain origin relation. Choropleth map of summed thickness of calcareous sandstone deserves that it mainly appear in area of uranium body and related cause of formation of ore body of interlayer deacidizing--oxidation belt. (authors)

Lithofacies Architecturing and Hydrocarbon Reservoir Potential of Lumshiwal Formation: Surghar Range, Trans-Indus Ranges, North Pakistan

Directory of Open Access Journals (Sweden)

Iftikhar Alam

2015-12-01

Full Text Available Western environs of the Indo-Pak Plate are comprised of thick Mesozoic sedimentary sequence and extensively extended toward Trans-Indus Salt ranges of North Pakistan. This sequence consists of detrital clastic sediments in the lower level and shallow to deep marine sediments in the upper level. In the Trans-Indus Salt ranges the Lumshiwal Formation represents the transitional level of the lower Cretaceous sequence. In Surghar Range the lower part of formation is composed of cyclic alteration of clayey, silty, very fine grained greenish gray, glauconitic sandstone to rusty brownish gray sandstone. The middle part of formation is comprised of thick bedded to massive, cliff forming, sugary texture, whitish to light yellowish gray occasionally rusty brownish gray medium to coarse grained, moderate to well cemented sandstone. The upper part is comprised of feldspathic, ferruginous, weathering yellowish brown, rusty brown to light gray with locally calcareous sandstone beds. The sandstone is reddish to brownish gray, coarse to granules texture, moderately cemented thick bedded to massive. Total thickness of the formation is 220m at Baroch Nala section 230m in Karandi section at a dip of 60°. Along trend lithological variations and diversified primary sedimentary structures which classifies fifteen different sub-lithofacie in Lumshiwal. Middle and upper parts of the formation show massive to thick, current bedded deposits. Lithofacies analysis revealed that the Lumshiwal Formation was deposited in shallow marine for the lower cyclic part to transitionally prodeltaic to deltaic for the middle to upper part respectively. High silica contents in the upper part compare to the middle and lower part of the formation. On the basis of high silica and low alumina with other low fractions of rock fragments, the sandstone is categorized into quartzarenite, sub-litharenite and sub-arkose. Cross beds in the middle and upper parts of formation indicate west to east

Water Vapor Diffusion and Adsorption of Sandstones: Influence of Rock Texture and Composition

Directory of Open Access Journals (Sweden)

Martin Keppert

2016-01-01

Full Text Available The term sandstone is used for wide range of rocks containing quartz clasts which can be cemented by secondary precipitated quartz or calcite; moreover the space between clasts can be filled by matrix. These facts result in existence of numerous rocks having highly various properties. Sandstones have been used as construction materials due to their good accessibility and workability. Since most of sandstones are porous, water vapor can penetrate through sandstone constructions. The rate of water vapor diffusion, as well as the vapor sorption isotherm, was determined for range of sandstone types. The diffusion resistance factor was found to be dependent on the total porosity of sandstone but the sorption behavior was strongly influenced by nature of the particular sandstone; the specific surface area of stone and presence of clay matrix are determining its sorption isotherm. The published data enable estimating (i diffusion resistance factor of a sandstone via knowledge of its total porosity and (ii the sorption isotherm via knowledge of the stone’s nature and specific surface area. This approach can significantly reduce the time necessary to acquire vapor-related properties of a sandstone.

ELECTRODEPOSITION OF COPPER IONS ON FIXED BED ELECTRODES: KINETIC AND HYDRODYNAMIC STUDY

Directory of Open Access Journals (Sweden)

L.A.M. Ruotolo

2002-03-01

Full Text Available The kinetic and hydrodynamic behaviour of a fixed-bed electrochemical reactor was studied in terms of current efficiency (CE and energy efficiency (EE. In the kinetic experiments the effects of fixed bed thickness (L, current density (i and initial concentration of copper (C0 were studied. In the hydrodynamic experiments the permeability (k of the electrode and the coefficient for inertial forces (c were also studied as functions of the applied current density. At low current densities and bed thicknesses greater than 1.0 cm, negative CE and EE were observed as a consequence of the dissolution of the porous matrix. At high current densities low CE and EE were observed and a powdery deposit was formed on the surface of the particles. From the results of the kinetic study bed thickness and the range of current densities employed in the hydrodynamic experiments were chosen. In these experiments the electrodeposition process continued until the whole electrode had been clogged and no more electrolyte could pass through it. The relationship between pressure drop and flow rate was well described by the Forchheimer equation. It was observed that the reduction in porosity due to copper electrodeposition causes the flow rate to decrease because of the decrease in electrode permeability, but it had no influence on current efficiency.

Depositional Architecture of Late Cambrian-Early Ordovician Siliciclastic Barik Formation; Al Huqf Area, Oman

Science.gov (United States)

Abbasi, Iftikhar Ahmed

2017-04-01

Early Paleozoic siliciclastics sediments of the Haima Supergroup are subdivided into a number of formations and members based on lithological characteristics of various rock sequences. One of the distinct sandstone sequence, the Barik Formation (Late Cambrian-Early Ordovician) of the Andam Group is a major deep gas reservoir in central Oman. The sandstone bodies are prospective reservoir rocks while thick shale and clay interbeds act as effective seal. Part of the Barik Formation (lower and middle part) is exposed in isolated outcrops in Al Huqf area as interbedded multistoried sandstone, and green and red shale. The sandstone bodies are up to 2 meters thick and can be traced laterally for 300 m to over 1 km. Most of sandstone bodies show both lateral and vertical stacking. Two types of sandstone lithofacies are identified on the basis of field characteristics; a plane-bedded sandstone lithofacies capping thick red and green color shale beds, and a cross-bedded sandstone lithofacies overlying the plane-bedded sandstone defining coarsening upward sequences. The plane-bedded sandstone at places contains Cruziana ichnofacies and bivalve fragments indicating deposition by shoreface processes. Thick cross-bedded sandstone is interpreted to be deposited by the fluvial dominated deltaic processes. Load-casts, climbing ripples and flaser-bedding in siltstone and red shale indicate influence of tidal processes at times during the deposition of the formation. This paper summarizes results of a study carried out in Al Huqf area outcrops to analyze the characteristics of the sandstone-body geometry, internal architecture, provenance and diagenetic changes in the lower and middle part of the formation. The study shows build-up of a delta complex and its progradation over a broad, low-angle shelf where fluvial processes operate beside shoreface processes in a vegetation free setting. Keywords: Andam Group, Barik Formation, Ordovician sandstone, Al Huqf, Central Oman,

Permeability estimation from NMR diffusion measurements in reservoir rocks.

Science.gov (United States)

Balzarini, M; Brancolini, A; Gossenberg, P

1998-01-01

It is well known that in restricted geometries, such as in porous media, the apparent diffusion coefficient (D) of the fluid depends on the observation time. From the time dependence of D, interesting information can be derived to characterise geometrical features of the porous media that are relevant in oil industry applications. In particular, the permeability can be related to the surface-to-volume ratio (S/V), estimated from the short time behaviour of D(t), and to the connectivity of the pore space, which is probed by the long time behaviour of D(t). The stimulated spin-echo pulse sequence, with pulsed magnetic field gradients, has been used to measure the diffusion coefficients on various homogeneous and heterogeneous sandstone samples. It is shown that the petrophysical parameters obtained by our measurements are in good agreement with those yielded by conventional laboratory techniques (gas permeability and electrical conductivity). Although the diffusing time is limited by T1, eventually preventing an observation of the real asymptotic behaviour, and the surface-to-volume ratio measured by nuclear magnetic resonance is different from the value obtained by BET because of the different length scales probed, the measurement remains reliable and low-time consuming.

Modes of heat removal from a heat-generating debris bed

International Nuclear Information System (INIS)

Squarer, D.; Hochreiter, L.E.; Piecznski, A.T.

1984-01-01

In the worst hypothetical accident in a light water reactor, when all protection systems fail, the core could be converted into a deep particulate bed either in-vessel or ex-vessel. The containment of such an accident depends on the coolability of a heat-generating debris bed. Some recent experimental and analytical studies that are concerned with heat removal from such a particulate bed are reviewed. Studies have indicated that bed dryout flux and, therefore, the heat removal rate from the particulate bed increases with the particle diameter (i.e., the permeability) for pool boiling conditions and can exceed the critical heat flux of a flat plate. Bed dryout in a large particle bed (i.e., a few millimetres) was found to be closely related to the ''flooding'' limit of the bed. Dryout under forced flow conditions was found to be affected by both forced and natural convection for mass flow rate smaller than m /SUB cr/ , whereas above this mass flow rate, bed dryout is proportional to the mass flow rate. Recent analyses were found to be in agreement with experimental data; however, additional research is needed to assess factors not accounted for in previous studies (e.g., effect of pressure, multidimensionality, stratification, etc.). Based on the expected pressure and particle sizes in a postulated severe accident sequence, a debris bed should be coolable, given a sufficient water supply

Regional hydrology of the Green River-Moab area, northwestern Paradox Basin, Utah

International Nuclear Information System (INIS)

Rush, F.E.; Whitfield, M.S.; Hart, I.M.

1982-12-01

The Green River-Moab area encompasses about 7800 square kilometers or about 25% of the Paradox basin. The entire Paradox basin is a part of the Colorado Plateaus that is underlain by a thick sequence of evaporite (salt) beds of Pennsylvanian age. The rock units that underlie the area have been grouped into hydrogeologic units based on their water-transmitting ability. Confining beds consist of evaporite beds of mostly salt, and overlying and underlying thick sequences of rocks with minimal permeability; above and below these confining beds are aquifers. The upper Mesozoic sandstone aquifer, probably is the most permeable hydrogeologic unit of the area and is the subject of this investigation. The principal component of groundwater outflow from this aquifer probably is subsurface flow to regional streams (the Green and Colorado Rivers) and is about 100 million cubic meters per year. All other components of outflow are relatively small. The average annual recharge to the aquifer is about 130 million cubic meters, of which about 20 million cubic meters is from local precipitation. For the lower aquifer, all recharge and discharge probably is by subsurface flow and was not estimated. The aquifers are generally isolated from the evaporite beds by the bounding confining beds; as a result, most ground water has little if any contact with the evaporites. Brines are present in the confining beds, but solution of beds of salt probably is very slow in most parts of the area. No brine discharges have been identified

Facies architecture of the Bluejacket Sandstone in the Eufaula Lake area, Oklahoma: Implications for the reservoir characterization of the Bartlesville Sandstone

Energy Technology Data Exchange (ETDEWEB)

Ye, Liangmiao; Yang, Kexian [Univ. of Tulsa, OK (United States)

1997-08-01

Outcrop studies of the Bluejacket Sandstone (Middle Pennsylvanian) provide significant insights to reservoir architecture of the subsurface equivalent Bartlesville Sandstone. Quarry walls and road cuts in the Lake Eufaula area offer excellent exposures for detailed facies architectural investigations using high-precision surveying, photo mosaics. Directional minipermeameter measurements are being conducted. Subsurface studies include conventional logs, borehole image log, and core data. Reservoir architectures are reconstructed in four hierarchical levels: multi-storey sandstone, i.e. discrete genetic intervals; individual discrete genetic interval; facies within a discrete genetic interval; and lateral accretion bar deposits. In both outcrop and subsurface, the Bluejacket (Bartlesville) Sandstone comprises two distinctive architectures: a lower braided fluvial and an upper meandering fluvial. Braided fluvial deposits are typically 30 to 80 ft thick, and are laterally persistent filling an incised valley wider than the largest producing fields. The lower contact is irregular with local relief of 50 ft. The braided-fluvial deposits consist of 100-400-ft wide, 5-15-ft thick channel-fill elements. Each channel-fill interval is limited laterally by an erosional contact or overbank deposits, and is separated vertically by discontinuous mudstones or highly concentrated mudstone interclast lag conglomerates. Low-angle parallel-stratified or trough cross-stratified medium- to coarse-grained sandstones volumetrically dominate. This section has a blocky well log profile. Meandering fluvial deposits are typically 100 to 150 ft thick and comprise multiple discrete genetic intervals.

Stratigraphy and environments of deposition of the Cretaceous Hell Creek Formation (reconnaissance) and the Paleocene Ludlow Formation (detailed), southwestern North Dakota. Report of investigations No. 56

International Nuclear Information System (INIS)

Moore, W.L.

1976-01-01

The Cretaceous Hell Creek and Paleocene Ludlow Formations of southwestern North Dakota, with the exception of the included lignite beds and minor amounts of concretions and nodules, are almost exclusively clastic sediments and sedimentary rocks. Massive clays, clays alternating with silts and sands, sandstones filling channels and other depressions, sheet sandstones, and lignites are the dominant sediment and rock types present. These sediments and sedimentary rocks were mostly deposited in a continental environment and were largely alluvial, lacustrine or paludal in origin; though marginal marine deposition, in part, is indicated by the occurrence of brackish water faunas in portions of the upper Ludlow Formation. With the possible exception of a persistent lignite near the base, persistent lignites are not present in the Hell Creek Formation. The Ludlow can be subdivided into several informal units, typically coal-bounded, which can be traced laterally over large areas. This informal subdivision permits isolation of stratigraphic units for the study of local environments of deposition. Channel and depression fill sandstones of the Ludlow Formation have a relatively low permeability and a high organic content at the surface and, for this reason, are considered poor prospective uranium host rocks. The lighter colored yellow winnowed sheet sandstones of the Ludlow are more permeable and relatively free of organic matter. They are considered as possible host rocks for uranium occurring in association with an oxidation/reduction interface at shallow depths. The uranium potential is enhanced where the latter sandstones occur along paleodivides which have been overlain by the Oligocene White River Formation, or in local areas where the latter formation is still preserved. Light yellow winnowed sheet sandstones are rare in the Hell Creek Formation, and the chances for uranium prospects in this interval seem correspondingly reduced

Characterization of application of acu sandstone in ceramic mass

International Nuclear Information System (INIS)

Nobrega, L.F.P.M.; Souza, M.M.; Gomes, Y.S.; Fernandes, D.L.

2016-01-01

The sandstone is a sedimentary rock formed mainly by quartz grains. In Rio Grande do Norte, there is the Potiguar Basin with the Jandaira and Acu Formations. The latter consists of thick layers of whitish-colored sandstones. It stands out as a water storage facility in the state, but it is also used for building aggregates. This article aimed at the use of the sandstone of this formation in the ceramic mass for coating. Initially, the material was sampled. It went through the comminution process to achieve the required granulometry. After this, three formulations were made to incorporate this new material into the traditional ones. The methods were performed according to ISO 13816. After sintering at 1200 °C, the specimens were subjected to the physical tests. A positive result was obtained for the use of the Acu sandstone in low concentrations. It is clear, therefore, its use in ceramics for coating

Contribution to the modeling of the anisotropic damage and the variation of the permeability of the brittle rocks

International Nuclear Information System (INIS)

Zhou, J.

2006-03-01

This work deals with a modeling of the mechanical and hydro-mechanical behaviour of saturated rocks taking into account the variation of the permeability with damage. At first is established a function of the free enthalpy by a direct micro-mechanical approach in taking into account the distribution of the microcrack length. The opening of the closed microcracks due to the tangential gliding is taken into account because of the roughness of the cracks surfaces. This opening contributes directly to the volume expansion and to the variation of the macroscopic permeability of the material. A phenomenological approach with an approximation by a damage tensor of two order is shown too. Then, an extension of the model is proposed for describing the poro-mechanical behaviour of saturated rocks. The poro-mechanical answers in drained and undrained conditions of the Vosges sandstone have been studied. In the last part, a coupled model describing the behaviour of the coupling between the induced damage and the variation of the rocks permeability is proposed. (O.M.)

Examples from the 1.6 Ga Chorhat Sandstone, Vindhyan

Indian Academy of Sciences (India)

This paper addresses macroscopic signatures of microbial mat-related structures within the 1.6 Ga-old Chorhat Sandstone of the Semri Group –the basal stratigraphic unit of the Vindhyan succession in Son valley.The Chorhat Sandstone broadly represents a prograding succession of three depositional facies ranging from ...

Trilobites from the Middle Ordovician Stairway Sandstone, Amadeus Basin, central Australia

DEFF Research Database (Denmark)

Jakobsen, Kristian Grube; Nielsen, Arne Thorshøj; Harper, David Alexander Taylor

2014-01-01

During the Middle Ordovician (Darriwilian) sandstones and siltstones were deposited in the epicontinental Larapintine Sea, which covered large parts of central Australia. The Darriwilian Stairway Sandstone has, for the first time, been sampled stratigraphically for macrofossils to track marine...... benthic biodiversity in this clastic-dominated shallow-water palaeoenvironment situated along the margin of northeastern Gondwana. The faunas from the Stairway Sandstone are generally of low diversity and dominated by bivalves but include several animal groups, with trilobites representing 25......% of the entire shelly fauna. Thirteen trilobite taxa are described from the Stairway Sandstone; the fauna displays a high degree of endemism. One new species, Basilicus (Parabasilicus) brumbyensis sp. nov. is described....

Effects of heat-flow and hydrothermal fluids from volcanic intrusions on authigenic mineralization in sandstone formations

Directory of Open Access Journals (Sweden)

Wolela Ahmed

2002-06-01

Full Text Available Volcanic intrusions and hydrothermal activity have modified the diagenetic minerals. In the Ulster Basin, UK, most of the authigenic mineralization in the Permo-Triassic sandstones pre-dated tertiary volcanic intrusions. The hydrothermal fluids and heat-flow from the volcanic intrusions did not affect quartz and feldspar overgrowths. However, clay mineral-transformation, illite-smectite to illite and chlorite was documented near the volcanic intrusions. Abundant actinolite, illite, chlorite, albite and laumontite cementation of the sand grains were also documented near the volcanic intrusions. The abundance of these cementing minerals decreases away from the volcanic intrusions.In the Hartford Basin, USA, the emplacement of the volcanic intrusions took place simultaneous with sedimentation. The heat-flow from the volcanic intrusions and hydrothermal activity related to the volcanics modified the texture of authigenic minerals. Microcrystalline mosaic albite and quartz developed rather than overgrowths and crystals near the intrusions. Chlorite clumps and masses were also documented with microcrystalline mosaic albite and quartz. These features are localized near the basaltic intrusions. Laumontite is also documented near the volcanic intrusions. The reservoir characteristics of the studied sandstone formations are highly affected by the volcanic and hydrothermal fluids in the Hartford and the Ulster Basin. The porosity dropped from 27.4 to zero percent and permeability from 1350 mD to 1 mD.

Improvement of Carbon Dioxide Sweep Efficiency by Utilization of Microbial Permeability Profile Modification to Reduce the Amount of Oil Bypassed During Carbon Dioxide Flood

Energy Technology Data Exchange (ETDEWEB)

Schmitz, Darrel [Mississippi State Univ., Mississippi State, MS (United States); Brown, Lewis [Mississippi State Univ., Mississippi State, MS (United States); Lynch, F. Leo [Mississippi State Univ., Mississippi State, MS (United States); Kirkland, Brenda L. [Mississippi State Univ., Mississippi State, MS (United States); Collins, Krystal M. [Mississippi State Univ., Mississippi State, MS (United States); Funderburk, William K. [Mississippi State Univ., Mississippi State, MS (United States)

2010-12-31

The objective of this project was to couple microbial permeability profile modification (MPPM), with carbon dioxide flooding to improve oil recovery from the Upper Cretaceous Little Creek Oil Field situated in Lincoln and Pike counties, MS. This study determined that MPPM technology, which improves production by utilizing environmentally friendly nutrient solutions to simulate the growth of the indigenous microflora in the most permeable zones of the reservoir thus diverting production to less permeable, previously unswept zones, increased oil production without interfering with the carbon dioxide flooding operation. Laboratory tests determined that no microorganisms were produced in formation waters, but were present in cores. Perhaps the single most significant contribution of this study is the demonstration that microorganisms are active at a formation temperature of 115°C (239°F) by using a specially designed culturing device. Laboratory tests were employed to simulate the MPPM process by demonstrating that microorganisms could be activated with the resulting production of oil in coreflood tests performed in the presence of carbon dioxide at 66°C (the highest temperature that could be employed in the coreflood facility). Geological assessment determined significant heterogeneity in the Eutaw Formation, and documented relatively thin, variably-lithified, well-laminated sandstone interbedded with heavily-bioturbated, clay-rich sandstone and shale. Live core samples of the Upper Cretaceous Eutaw Formation from the Heidelberg Field, MS were quantitatively assessed using SEM, and showed that during MPPM permeability modification occurs ubiquitously within pore and throat spaces of 10-20 μm diameter. Testing of the MPPM procedure in the Little Creek Field showed a significant increase in production occurred in two of the five production test wells; furthermore, the decline curve in each of the production wells became noticeably less steep. This project greatly

Feasibility of a data-constrained prediction of hydrocarbon reservoir sandstone microstructures

International Nuclear Information System (INIS)

Yang, Y S; Gureyev, T E; Tulloh, A; Clennell, M B; Pervukhina, M

2010-01-01

Microstructures are critical for defining material characteristics such as permeability, mechanical, electrical and other physical properties. However, the available techniques for determining compositional microstructures through segmentation of x-ray computed tomography (CT) images are inadequate when there are finer structures than the CT spatial resolution, i.e. when there is more than one material in each voxel. This is the case for CT imaging of geomaterials characterized with submicron porosity and clay coating that control petrophysical properties of rock. This note outlines our data-constrained modelling (DCM) approach for prediction of compositional microstructures, and our investigation of the feasibility of determining sandstone microstructures using multiple CT data sets with different x-ray beam energies. In the DCM approach, each voxel is assumed to contain a mixture of multiple materials, optionally including voids. Our preliminary comparisons using model samples indicate that the DCM-predicted compositional microstructure is consistent with the known original microstructure under low noise conditions. The approach is quite generic and is applicable to predictions of microstructure of various materials. (technical design note)

Sandstone-filled normal faults: A case study from central California

Science.gov (United States)

Palladino, Giuseppe; Alsop, G. Ian; Grippa, Antonio; Zvirtes, Gustavo; Phillip, Ruy Paulo; Hurst, Andrew

2018-05-01

Despite the potential of sandstone-filled normal faults to significantly influence fluid transmissivity within reservoirs and the shallow crust, they have to date been largely overlooked. Fluidized sand, forcefully intruded along normal fault zones, markedly enhances the transmissivity of faults and, in general, the connectivity between otherwise unconnected reservoirs. Here, we provide a detailed outcrop description and interpretation of sandstone-filled normal faults from different stratigraphic units in central California. Such faults commonly show limited fault throw, cm to dm wide apertures, poorly-developed fault zones and full or partial sand infill. Based on these features and inferences regarding their origin, we propose a general classification that defines two main types of sandstone-filled normal faults. Type 1 form as a consequence of the hydraulic failure of the host strata above a poorly-consolidated sandstone following a significant, rapid increase of pore fluid over-pressure. Type 2 sandstone-filled normal faults form as a result of regional tectonic deformation. These structures may play a significant role in the connectivity of siliciclastic reservoirs, and may therefore be crucial not just for investigation of basin evolution but also in hydrocarbon exploration.

Laboratory investigation of shale rock to identify fracture propagation in vertical direction to bedding

Science.gov (United States)

Peng, Tan; Yan, Jin; Bing, Hou; Yingcao, Zhou; Ruxin, Zhang; Zhi, Chang; Meng, Fan

2018-06-01

Affected by beddings and natural fractures, fracture geometry in the vertical plane is complex in shale formation, which differs from a simple fracture in homogeneous sandstone reservoirs. However, the propagation mechanism of a hydraulic fracture in the vertical plane has not been well understood. In this paper, a true tri-axial pressure machine was deployed for shale horizontal well fracturing simulation experiments of shale outcrops. The effects of multiple factors on hydraulic fracture vertical propagation were studied. The results revealed that hydraulic fracture initiation and propagation displayed four basic patterns in the vertical plane of laminated shale formation. A hydraulic fracture would cross the beddings under the high vertical stress difference between a vertical stress and horizontal minimum stress of 12 MPa, while a hydraulic fracture propagates along the beddings under a low vertical stress difference of 3 MPa. Four kinds of fracture geometry, including a single main fracture, a nonplanar fracture, a complex fracture, and a complex fracture network, were observed due to the combined effects of flow rate and viscosity. Due to the influence of binding strength (or cementing strength) on the fracture communication effects between a hydraulic fracture and the beddings, the opening region of the beddings takes the shape of an ellipse.

2D and 3D imaging resolution trade-offs in quantifying pore throats for prediction of permeability

Energy Technology Data Exchange (ETDEWEB)

Beckingham, Lauren E.; Peters, Catherine A.; Um, Wooyong; Jones, Keith W.; Lindquist, W.Brent

2013-09-03

Although the impact of subsurface geochemical reactions on porosity is relatively well understood, changes in permeability remain difficult to estimate. In this work, pore-network modeling was used to predict permeability based on pore- and pore-throat size distributions determined from analysis of 2D scanning electron microscopy (SEM) images of thin sections and 3D X-ray computed microtomography (CMT) data. The analyzed specimens were a Viking sandstone sample from the Alberta sedimentary basin and an experimental column of reacted Hanford sediments. For the column, a decrease in permeability due to mineral precipitation was estimated, but the permeability estimates were dependent on imaging technique and resolution. X-ray CT imaging has the advantage of reconstructing a 3D pore network while 2D SEM imaging can easily analyze sub-grain and intragranular variations in mineralogy. Pore network models informed by analyses of 2D and 3D images at comparable resolutions produced permeability esti- mates with relatively good agreement. Large discrepancies in predicted permeabilities resulted from small variations in image resolution. Images with resolutions 0.4 to 4 lm predicted permeabilities differ- ing by orders of magnitude. While lower-resolution scans can analyze larger specimens, small pore throats may be missed due to resolution limitations, which in turn overestimates permeability in a pore-network model in which pore-to-pore conductances are statistically assigned. Conversely, high-res- olution scans are capable of capturing small pore throats, but if they are not actually flow-conducting predicted permeabilities will be below expected values. In addition, permeability is underestimated due to misinterpreting surface-roughness features as small pore throats. Comparison of permeability pre- dictions with expected and measured permeability values showed that the largest discrepancies resulted from the highest resolution images and the best predictions of

Effective stress law for the permeability and deformation of four porous limestones

Science.gov (United States)

Wang, Y.; Meng, F.; Wang, X.; Baud, P.; Wong, T. F.

2017-12-01

The effective stress behavior of a rock is related to the geometric of its pore space. In a microscopically homogeneous assemblage, effective stress coefficients for permeability, volumetric strain and porosity change are predicted to be equal to or less than unity. Experimental measurements are in basic agreement with this prediction, with exceptions particularly in clay-rich sandstones, for which effective stress coefficient for permeability up to 7 was documented. Little is known about carbonates, but Ghabezloo et al. [2009] studied the permeability of an oolitic limestone (from Nimes, France) with 17% porosity and reported effective stress coefficients up to 2.4. We investigated this phenomenon in Indiana, Leitha, Purbeck, and Thala limestones with porosities of 13-30%. Measurements were made at room temperature on water-saturated samples at confining and pore pressures of 7-15 MPa and 1-3 MPa, respectively. Unlike previous studies limited to the permeability, we also determined the effective stress coefficients for volumetric strain and porosity change. Indiana limestone is oolitic, and not surprisingly its behaviour was similar to Nimes limestone, with an effective stress coefficient for permeability of 2.5. Our Indiana limestone data showed that whereas the effective stress coefficient for volumetric strain was 1. Measurements on Purbeck and Thala limestones are consistent with these inequalities, with effective stress coefficients for permeability and porosity change >1 and that for volumetric strain <1. Even though Purbeck and Thala limestones are micritic with appreciable amount of quartz and dolomite, microstructural and mercury porosimetry data showed that their pore spaces are similar to the oolitic limestones, in that the pore size distribution is bimodal with significant fractions of both macropores and micropores. Berryman [1992] analyzed theoretically a rock made up of two porous constituents. Our new data are in agreement with inequalities he

Hydro-geophysical responses to the injection of CO2 in core plugs of Berea sandstone

Science.gov (United States)

Song, I.; Park, K. G.

2017-12-01

We have built a laboratory-scale core flooding system to measure the relative permeability of a core sample and the acoustic response to the CO2 saturation degree at in situ condition of pressure and temperature down to a few kilometer depths. The system consisted of an acoustic velocity core holder (AVC model from the Core Laboratories) between upstream where CO2 and H2O were injected separately and downstream where the mixed fluids came out of a core sample. Core samples with 4 cm in diameter and 5 cm in length of Berea sandstone were in turn placed in the core holder for confining and axial pressures. The flooding operations of the multiphase fluids were conducted through the sample at 40ºC in temperature and 8 MPa in backpressure. CO2 and H2O in the physical condition were injected separately into a sample at constant rate with various ratios. The two phases were mixed during flowing through the sample. The mixed fluids out of the sample were separated again by their different densities in a chamber equipped with a level gauge of the interface. From the level change of the water in the separator, we measured the volume of water coming out of the sample for each test with a constant ratio of the injection rates. Then it was possible to calculate the saturation degree of CO2 from the difference between input volume and output volume of water. The differential pressure between upstream and downstream was directly measured to calculate the relative permeability as a function of the CO2 saturation degree. We also conducted ultrasonic measurements using piezoelectric sensors on the end plugs. An electric pulse was given to a sensor on one end of sample, and then ultrasonic waves were recorded from the other end. The various ratios of injection rate of CO2 and H2O into Berea sandstone yielded a range of 0.1-0.7 in CO2 saturation degree. The relative permeability was obtained at the condition of steady-state flow for given stages from the velocity of each phase and

Sandstone-type uranium deposits. Summary and conclusions

International Nuclear Information System (INIS)

Finch, W.I.

1985-01-01

The similarity of most of the deposits described in this report is striking even though they occur in sandstone host rocks ranging in age from Carboniferous to Tertiary and on every continent outside the polar regions. Geologic environments of the uranium deposits consist of distinctive sets of tectonic and sedimentary-depositional systems, all of which have some common threads of favorable geologic processes. In this summary paper it is hoped that this report has sharpened an understanding of the deposit's ''home environment'' that will aid future exploration for these resource-important sandstone-type uranium ores

Deformation bands in porous sandstones their microstructure and petrophysical properties

Energy Technology Data Exchange (ETDEWEB)

Torabi, Anita

2007-12-15

deformation bands are characterized by strain hardening, these new bands feature a central slip surface, which indicates late strain softening. They lack the characteristic compaction envelop, and are typified by higher porosity and lower permeability than previously-described cataclastic deformation bands. Intense background fracturing of the host rock and significant initial porosity are considered to be important in creating these newly-discovered deformation bands. In a related study, we investigate, for millimeter- wide deformation bands, the scale limitation inherent in laboratory measurements of porosity and permeability. The scale limitations imposed by the deformation band relative to the physical sample size motivated us to develop a new method for determining porosity and permeability based on image processing. While plug measurements measure the effective permeability across a 25.4 mm (1 inch) long sample, which includes both host rock and deformation band, the method presented here provides a means to estimate porosity and permeability of deformation band on microscale. This method utilizes low-order (one- and two orders) spatial correlation functions to analyze high-resolution, high-magnification backscatter images, to estimate the porosity and specific surface area of the pore-grain interface in the deformed sandstones. Further, this work demonstrates the use of a modified version of the Kozeny-Carmen relation to calculate permeability by using porosity and specific surface area obtained through the image processing. The result shows that permeability difference between the band and the host rock is up to four orders of magnitude. Moreover, the porosities and permeabilities estimated from image processing are lower than those obtained from their plug measurements; hence the traditional laboratory measurements have been overestimating permeability because of the previously-unrecognized scale problem. In addition, the image processing results clearly show that

Uranium favorability of tertiary sedimentary rocks of the Pend Oreille River valley, Washington

International Nuclear Information System (INIS)

Marjaniemi, D.K.; Robins, J.W.

1975-08-01

Tertiary sedimentary rocks in the Pend Oreille River valley were investigated in a regional study to determine the favorability for potential uranium resources of northeastern Washington. This project involved measurement and sampling of surface sections, collection of samples from isolated outcrops, chemical and mineralogical analyses of samples, and examination of available water well logs. The Box Canyon Dam area north of Ione is judged to have very high favorability. Thick-bedded conglomerates interbedded with sandstones and silty sandstones compose the Tiger Formation in this area, and high radioactivity levels are found near the base of the formation. Uranophane is found along fracture surfaces or in veins. Carbonaceous material is present throughout the Tiger Formation in the area. Part of the broad Pend Oreille valley surrounding Cusick, Washington, is an area of high favorability. Potential host rocks in the Tiger Formation, consisting of arkosic sandstones interbedded with radioactive shales, probably extend throughout the subsurface part of this area. Carbonaceous material is present and some samples contain high concentrations of uranium. In addition, several other possible chemical indicators were found. The Tiger-Lost Creek area is rated as having medium favorability. The Tiger Formation contains very hard, poorly sorted granite conglomerate with some beds of arkosic sandstone and silty sandstone. The granite conglomerate was apparently derived from source rocks having relatively high uranium content. The lower part of the formation is more favorable than the upper part because of the presence of carbonaceous material, anomalously high concentrations of uranium, and other possible chemical indicators. The area west of Ione is judged to have low favorability, because of the very low permeability of the rocks and the very low uranium content

Uranium favorability of tertiary sedimentary rocks of the Pend Oreille River valley, Washington. [Measurement and sampling of surface sections, collection of samples from isolated outcrops, chemical and mineralogical analyses of samples, and examination of available water logs

Energy Technology Data Exchange (ETDEWEB)

Marjaniemi, D.K.; Robins, J.W.

1975-08-01

Tertiary sedimentary rocks in the Pend Oreille River valley were investigated in a regional study to determine the favorability for potential uranium resources of northeastern Washington. This project involved measurement and sampling of surface sections, collection of samples from isolated outcrops, chemical and mineralogical analyses of samples, and examination of available water well logs. The Box Canyon Dam area north of Ione is judged to have very high favorability. Thick-bedded conglomerates interbedded with sandstones and silty sandstones compose the Tiger Formation in this area, and high radioactivity levels are found near the base of the formation. Uranophane is found along fracture surfaces or in veins. Carbonaceous material is present throughout the Tiger Formation in the area. Part of the broad Pend Oreille valley surrounding Cusick, Washington, is an area of high favorability. Potential host rocks in the Tiger Formation, consisting of arkosic sandstones interbedded with radioactive shales, probably extend throughout the subsurface part of this area. Carbonaceous material is present and some samples contain high concentrations of uranium. In addition, several other possible chemical indicators were found. The Tiger-Lost Creek area is rated as having medium favorability. The Tiger Formation contains very hard, poorly sorted granite conglomerate with some beds of arkosic sandstone and silty sandstone. The granite conglomerate was apparently derived from source rocks having relatively high uranium content. The lower part of the formation is more favorable than the upper part because of the presence of carbonaceous material, anomalously high concentrations of uranium, and other possible chemical indicators. The area west of Ione is judged to have low favorability, because of the very low permeability of the rocks and the very low uranium content. (auth)

Analyzing the Sand-fixing Effect of Feldspathic Sandstone from the Texture Characteristics

Science.gov (United States)

Zhang, lu; Ban, Jichang

2018-01-01

The purpose of this research was aimed to study the sand fixing effect of feldspathic sandstone in Mu Us Sandy Land, to provide a scienticic basis for desertification control, soil and water conservation and development of farming there. Methods of mixing feldspathic sandstone and aeolian sandy soil according to 1: 0, 1: 1, 1: 2, 1: 5, and 0: 1 mass ratioes, the graded composition and characteristics were studied with laser particle size analyzer. The result showed that these features of sand-based, loosely structured, easy to wind erosion of aeolian sandy soil were changed before feldspathic sandstone and aeolian sandy soil compounding. The <0.05 mm particle mass increased with feldspathic sandstone mass increasing. The texture presented this kind of change from sand to sandy loam to loam to silt loam. The small particle size distribution, good homogeneity and other features of aeolian sandy soil were improved to a certain degree, and the particle size distribution became broad before feldspathic sandstone and aeolian sandy soil compounding. The particle grading was continuous, and the grading characteristic was good when m(F): m(S) was 1: 5(Cu was 54.71 and Cc was 2.54) or when m(F): m(S) was 1: 2(Cu was 76.21, Cc was 1.12). The conclusion is that feldspathic sandstone has sand-fixing effect in texture characteristics, which heightens with feldspathic sandstone mass increasing, and when the mass ratio of feldspathic sandstone: aeolian sandy soil is 1: 2 or 1: 5 which compound better.

Structural and microstructural evolution of fault zones in Cretaceous poorly lithified sandstones of the Rio do Peixe basin, Paraiba, NE Brazil

Science.gov (United States)

Balsamo, Fabrizio; Nogueira, Francisco; Storti, Fabrizio; Bezerra, Francisco H. R.; De Carvalho, Bruno R.; André De Souza, Jorge

2017-04-01

In this contribution we describe the structural architecture and microstructural features of fault zones developed in Cretaceous, poorly lithified sandstones of the Rio do Peixe basin, NE Brazil. The Rio do Peixe basin is an E-W-trending, intracontinental half-graben basin developed along the Precambrian Patos shear zone where it is abutted by the Porto Alegre shear zone. The basin formed during rifting between South America and Africa plates and was reactivated and inverted in a strike-slip setting during the Cenozoic. Sediments filling the basin consist of an heterolithic sequence of alternating sandstones, conglomerates, siltstone and clay-rich layers. These lithologies are generally poorly lithified far from the major fault zones. Deformational structures in the basin mostly consist of deformation band-dominated fault zones. Extensional and strike-slip fault zones, clusters of deformation bands, and single deformation bands are commonly well developed in the proximity of the basin-boundary fault systems. All deformation structures are generally in positive relief with respect to the host rocks. Extensional fault zones locally have growth strata in their hangingwall blocks and have displacement generally <10 m. In map view, they are organized in anastomosed segments with high connectivity. They strike E-W to NE-SW, and typically consist of wide fault cores (< 1 m in width) surrounded by up to few-meter wide damage zones. Fault cores are characterized by distributed deformation without pervasive strain localization in narrow shear bands, in which bedding is transposed into foliation imparted by grain preferred orientation. Microstructural observations show negligible cataclasis and dominant non-destructive particulate flow, suggesting that extensional fault zones developed in soft-sediment conditions in a water-saturated environment. Strike-slip fault zones commonly overprint the extensional ones and have displacement values typically lower than about 2 m. They

Diagenetic Evolution and Reservoir Quality of Sandstones in the North Alpine Foreland Basin: A Microscale Approach.

Science.gov (United States)

Gross, Doris; Grundtner, Marie-Louise; Misch, David; Riedl, Martin; Sachsenhofer, Reinhard F; Scheucher, Lorenz

2015-10-01

Siliciclastic reservoir rocks of the North Alpine Foreland Basin were studied focusing on investigations of pore fillings. Conventional oil and gas production requires certain thresholds of porosity and permeability. These parameters are controlled by the size and shape of grains and diagenetic processes like compaction, dissolution, and precipitation of mineral phases. In an attempt to estimate the impact of these factors, conventional microscopy, high resolution scanning electron microscopy, and wavelength dispersive element mapping were applied. Rock types were established accordingly, considering Poro/Perm data. Reservoir properties in shallow marine Cenomanian sandstones are mainly controlled by the degree of diagenetic calcite precipitation, Turonian rocks are characterized by reduced permeability, even for weakly cemented layers, due to higher matrix content as a result of lower depositional energy. Eocene subarkoses tend to be coarse-grained with minor matrix content as a result of their fluvio-deltaic and coastal deposition. Reservoir quality is therefore controlled by diagenetic clay and minor calcite cementation.Although Eocene rocks are often matrix free, occasionally a clay mineral matrix may be present and influence cementation of pores during early diagenesis. Oligo-/Miocene deep marine rocks exhibit excellent quality in cases when early cement is dissolved and not replaced by secondary calcite, mainly bound to the gas-water contact within hydrocarbon reservoirs.

ANALYSIS OF OIL-BEARING CRETACEOUS SANDSTONE HYDROCARBON RESERVOIRS, EXCLUSIVE OF THE DAKOTA SANDSTONE, ON THE JICARILLA APACHE INDIAN RESERVATION, NEW MEXICO

International Nuclear Information System (INIS)

Jennie Ridgley

2000-01-01

An additional 450 wells were added to the structural database; there are now 2550 wells in the database with corrected tops on the Juana Lopez, base of the Bridge Creek Limestone, and datum. This completes the structural data base compilation. Fifteen oil and five gas fields from the Mancos-ElVado interval were evaluated with respect to the newly defined sequence stratigraphic model for this interval. The five gas fields are located away from the structural margins of the deep part of the San Juan Basin. All the fields have characteristics of basin-centered gas and can be considered as continuous gas accumulations as recently defined by the U.S. Geological Survey. Oil production occurs in thinly interbedded sandstone and shale or in discrete sandstone bodies. Production is both from transgressive and regressive strata as redefined in this study. Oil production is both stratigraphically and structurally controlled with production occurring along the Chaco slope or in steeply west-dipping rocks along the east margin of the basin. The ElVado Sandstone of subsurface usage is redefined to encompass a narrower interval; it appears to be more time correlative with the Dalton Sandstone. Thus, it was deposited as part of a regressive sequence, in contrast to the underlying rock units which were deposited during transgression

Permeability of shale at elevated temperature and pressure: Test methodology and preliminary results

International Nuclear Information System (INIS)

Myer, L.R.; Christian, T.L.

1987-05-01

A method of measuring the hydraulic conductivity of low permeability shale as a function of pressure and temperature has been developed and successfully demonstrated. Measurements have been performed on samples of Green River Formation up to a temperature of 140 0 C. For flow parallel to bedding hydraulic conductivities increased nonlinearly from 1.75 x 10 -16 m/s (1.6 x 10 -23 m 2 ) at 25 0 C, to 5.6 x 10 -15 m/s (1.4 x 10 -22 m 2 ) at 140 0 C. This increase in permeability with temperature may reflect an increase in microcrack porosity resulting from the heating

Double-layer structure model of the uranium generating bed in the land basins of the northwestern China and its significance

International Nuclear Information System (INIS)

Wang Zhilong

1988-04-01

The paper puts forward a double layer structure model of uranium generating bed in the land basins of Northwestern China, i.e. uranium ganerating bed = source layer of uranium+gathering uranium layer. The mechanism of its formation: Feldspar was hydromicatized. Some feldspar, quarts detrital silicate minerals were replaced to redden by the authigenesis of hematite and goethite. In the course of the oxidation, a little uranium is released from the detrital minerals. Because of the oxidation environment, the released uranium wasn't able to be precipitated, only to diffuse to the adjacent grey bed which has low Eh value with uranium-bearing 'stagnant water' fixed in pores during the dewatering process of the diagenesis and form minable uranium deposit. The significance of the model for uranium prospecting are as follows: (1) Uranium source range is much expanded concerning ruanium prospecting in sandstone. (2) For the potential assessment of basin and the selection of potential area, the model is an important prospecting criterion. (3) By using the main criterion uranium-generating bed-arkosic red beds well, the buried ore bodies can be found provided that arkosic red beds were regarded as a significant criterion of uranium-generating bed

Experimental evaluation on the damages of different drilling modes to tight sandstone reservoirs

Directory of Open Access Journals (Sweden)

Gao Li

2017-07-01

Full Text Available The damages of different drilling modes to reservoirs are different in types and degrees. In this paper, the geologic characteristics and types of such damages were analyzed. Then, based on the relationship between reservoir pressure and bottom hole flowing pressure corresponding to different drilling modes, the experimental procedures on reservoir damages in three drilling modes (e.g. gas drilling, liquid-based underbalanced drilling and overbalanced drilling were designed. Finally, damage simulation experiments were conducted on the tight sandstone reservoir cores of the Jurassic Ahe Fm in the Tarim Basin and Triassic Xujiahe Fm in the central Sichuan Basin. It is shown that the underbalanced drilling is beneficial to reservoir protection because of its less damage on reservoir permeability, but it is, to some extent, sensitive to the stress and the empirical formula of stress sensitivity coefficient is obtained; and that the overbalanced drilling has more reservoir damages due to the invasion of solid and liquid phases. After the water saturation of cores rises to the irreducible water saturation, the decline of gas logging permeability speeds up and the damage degree of water lock increases. It is concluded that the laboratory experiment results of reservoir damage are accordant with the reservoir damage characteristics in actual drilling conditions. Therefore, this method reflects accurately the reservoir damage characteristics and can be used as a new experimental evaluation method on reservoir damage in different drilling modes.

Cense Explosion Test Program. Report 1. Cense 1. Explosions in Sandstone

Science.gov (United States)

1977-09-01

series, "Analysis and Summary of CENSE Data." 10 * _ CHAPTER 2 APPROACH 2.1 DESCRIPTION OF TEST SITE An exposed outcrop of Kayenta sandstone with 180...ft/s seismic velocity previously determined (References 12-14) for the unweathered upper zone of the Kayenta sandstone. 16 I The P-wave propagation...Propagation along the horizontal radial was 8400 ft/s. The seismic velocity pre- viously determined for Kayenta sandstone in this area was 7500 ft/s

Sandstone landforms shaped by negative feedback between stress and erosion

Czech Academy of Sciences Publication Activity Database

Bruthans, J.; Soukup, J.; Vaculíková, J.; Filippi, Michal; Schweigstillová, Jana; Mayo, A. L.; Mašín, D.; Kletetschka, Günther; Řihošek, J.

2014-01-01

Roč. 7, č. 8 (2014), s. 597-601 ISSN 1752-0894 R&D Projects: GA ČR GA13-28040S Institutional support: RVO:67985831 ; RVO:67985891 Keywords : sandstone * sandstone landsforms * stress * erosion Subject RIV: DB - Geology ; Mineralogy Impact factor: 11.740, year: 2014

Characterization of Rock Mechanical Properties Using Lab Tests and Numerical Interpretation Model of Well Logs

Directory of Open Access Journals (Sweden)

Hao Xu

2016-01-01

Full Text Available The tight gas reservoir in the fifth member of the Xujiahe formation contains heterogeneous interlayers of sandstone and shale that are low in both porosity and permeability. Elastic characteristics of sandstone and shale are analyzed in this study based on petrophysics tests. The tests indicate that sandstone and mudstone samples have different stress-strain relationships. The rock tends to exhibit elastic-plastic deformation. The compressive strength correlates with confinement pressure and elastic modulus. The results based on thin-bed log interpretation match dynamic Young’s modulus and Poisson’s ratio predicted by theory. The compressive strength is calculated from density, elastic impedance, and clay contents. The tensile strength is calibrated using compressive strength. Shear strength is calculated with an empirical formula. Finally, log interpretation of rock mechanical properties is performed on the fifth member of the Xujiahe formation. Natural fractures in downhole cores and rock microscopic failure in the samples in the cross section demonstrate that tensile fractures were primarily observed in sandstone, and shear fractures can be observed in both mudstone and sandstone. Based on different elasticity and plasticity of different rocks, as well as the characteristics of natural fractures, a fracture propagation model was built.

Permeability of fissured rock - an experimental study with special regard to the water injection test

International Nuclear Information System (INIS)

Schneider, H.J.

1987-01-01

The permeability to water of fissured rock is one of the most important design parameters for many underground projects, such as, e.g. the final deposition of radioactive waste. Because the conventional water injection test according to LUGEON for the calculation of permeability to water is associated with a high degree of uncertainty, new test equipment was developed. This equipment works on the principle of the water injection tracer test and multi-level measurements, enabling detailed measurement of the flow process at injection site and in the rock. The tests were carried out in Bunter sandstone and granite. The LUGEON test concept was varied in short-term and long-term tests at identical geological boundary conditions, and with test control at constant pressure on the one hand and at constant injection volume on the other. The test results show that non-steady-state flow occurs with short injection times, whereby the range is limited to the local rock at injection site. An increasing in injection time can lead to an increase in range by a number of factors as well as to steady-state flow conditions. The permeability of the rock types investigated is inhomgeneous and anistropic as a result of the fissured structure. (orig./HP) With 114 figs., 4 tabs [de

Electrokinetic desalination of sandstones for NaCl removal

DEFF Research Database (Denmark)

Ottosen, Lisbeth M.; Christensen, Iben V.

2012-01-01

of reliable methods to remove the damaging salts in order to stop the decay. Electrokinetic desalination of fired clay bricks have previously shown efficient in laboratory scale and in the present work the method is tested for desalination of Cotta and Posta sandstones, which both have lower porosity than...... each stone, but electroosmosis in the poultices may have caused suction/pressure over the interface between stone and poultice causing the differences in poultice water content. The transport numbers for Cl− and Na+ differed in the two stones and were highest in the most porous Cotta sandstone in spite...... of similar high pore water concentrations and the same applied electric current. The hypotheses is that a layered structure of the sandstones could be the cause for this, as the electric current may preferentially flow in certain paths through the stone, which are thus desalinated first. After...

On the migration of uranium isotopes in sandstone aquifers

International Nuclear Information System (INIS)

Froehlich, K.; Gellermann, R.

1982-01-01

Measurements of natural 238 U and 234 U activity in groundwater of sandstone aquifers have been used to study the migration of these uranium isotopes. Regarding the uranium exchange between liquid phase and rock surface during migration, two different models were applied for evaluating the experimental results. Values of corresponding parameters (retardation factor K, removal rate R) reflecting different behaviour concerning this exchange were determined. For example, the values obtained for 238 U in a Triassic sandstone aquifer of the GDR are K = 8.6 x 10 6 and R = 1.3 x 10 -3 a -1 , respectively. It was found that, under the conditions of the sandstone aquifer concerned, the removal rate model is better suited for calculating uranium-isotope migration in groundwater. (author)

A coupled transport and solid mechanics formulation with improved reaction kinetics parameters for modeling oxidation and decomposition in a uranium hydride bed.

Energy Technology Data Exchange (ETDEWEB)

Salloum, Maher N.; Shugard, Andrew D.; Kanouff, Michael P.; Gharagozloo, Patricia E.

2013-03-01

Modeling of reacting flows in porous media has become particularly important with the increased interest in hydrogen solid-storage beds. An advanced type of storage bed has been proposed that utilizes oxidation of uranium hydride to heat and decompose the hydride, releasing the hydrogen. To reduce the cost and time required to develop these systems experimentally, a valid computational model is required that simulates the reaction of uranium hydride and oxygen gas in a hydrogen storage bed using multiphysics finite element modeling. This SAND report discusses the advancements made in FY12 (since our last SAND report SAND2011-6939) to the model developed as a part of an ASC-P&EM project to address the shortcomings of the previous model. The model considers chemical reactions, heat transport, and mass transport within a hydride bed. Previously, the time-varying permeability and porosity were considered uniform. This led to discrepancies between the simulated results and experimental measurements. In this work, the effects of non-uniform changes in permeability and porosity due to phase and thermal expansion are accounted for. These expansions result in mechanical stresses that lead to bed deformation. To describe this, a simplified solid mechanics model for the local variation of permeability and porosity as a function of the local bed deformation is developed. By using this solid mechanics model, the agreement between our reacting bed model and the experimental data is improved. Additionally, more accurate uranium hydride oxidation kinetics parameters are obtained by fitting the experimental results from a pure uranium hydride oxidation measurement to the ones obtained from the coupled transport-solid mechanics model. Finally, the coupled transport-solid mechanics model governing equations and boundary conditions are summarized and recommendations are made for further development of ARIA and other Sandia codes in order for them to sufficiently implement the model.

Greybull Sandstone Petroleum Potential on the Crow Indian Reservation, South-Central Montana

Energy Technology Data Exchange (ETDEWEB)

Lopez, David A.

2002-05-13

The focus of this project was to explore for stratigraphic traps that may be present in valley-fill sandstone at the top of the Lower Cretaceous Kootenai Formation. This sandstone interval, generally known as the Greybull Sandstone, has been identified along the western edge of the reservation and is a known oil and gas reservoir in the surrounding region. The Greybull Sandstone was chosen as the focus of this research because it is an excellent, well-documented, productive reservoir in adjacent areas, such as Elk Basin; Mosser Dome field, a few miles northwest of the reservation; and several other oil and gas fields in the northern portion of the Bighorn Basin.

Discussion on distribution characteristics of calcareous sandstone in Shihongtan uranium deposit and its genesis

International Nuclear Information System (INIS)

Zhu Huanqiao; Qiao Haiming; Jia Heng; Xu Gaozhong

2007-01-01

Based on the observation and statistics on the calcareous sandstone in the ore host layer in Shihongtan uranium deposit, this paper finds that the calcareous sandstone occurs on and off near the top or wash surface of the sandbody as beads-strings lens along the layer and concentrates in the area where the ore bodies are rich. In lithology, the calcareous sandstone is of coarse grain and fairly well sorted. According to the analysis on the lithogeochemical features and the carbon and oxygen isotopes of calcareous sandstones, it is realized that there some genetic relation between the formation of calcareous sandstone and uranium mineralization in the oxidation-deoxidation transitional belt, that is the precipitation and enrichment of uranium is accompanied by the deposition of carbonate and formation of calcareous sandstone. (authors)

The influence of clay minerals on acoustic properties of sandstones

Energy Technology Data Exchange (ETDEWEB)

Hansen, Olav

1997-12-31

This thesis aims to provide better understanding of the relationship between the acoustic properties and the petrophysical/mineralogical properties in sand-prone rock. It emphasizes the influence of clay minerals. The author develops a method to deposit clay minerals/mineral aggregates in pore space of a rigid rock framework. Kaolinite aggregates were flushed into porous permeable Bentheimer sandstone to evaluate the effect of pore filling minerals on porosity, permeability and acoustic properties. The compressional velocity was hardly affected by the clay content and it was found that the effect of minor quantities of pore filling minerals may be acoustically modelled as an ideal suspension, where the pore fluid bulk modulus is modified by the bulk modulus of the clay minerals. The influence of clays on acoustic velocities in petroleum reservoir rocks was investigated through ultrasonic measurements of compressional- and shear-waves on core material from reservoir and non-reservoir units on the Norwegian Continental Shelf. The measured velocities decrease as the porosity increases, but are not strongly dependent on the clay content. The measured velocities are less dependent on the petrophysical and lithological properties than indicated by previous authors and published mathematical models, and stiffness reduction factors are introduced in two of the models to better match the data. Velocities are estimated along the wellbores based on non-sonic well logs and reflect well the actual sonic log well measurements. In some wells the compressional velocity cannot be modelled correctly by the models suggested. Very high compressional wave anisotropy was measured in the dry samples at atmospheric conditions. As the samples were saturated, the anisotropy was reduced to a maximum of about 30% and decreases further upon pressurization. Reservoir rocks retrieved from 2500 m are more stress dependent than those retrieved from less than 200 m depth. 168 refs., 117 figs., 24

A complex investigation of building sandstones from Saxony (Germany)

International Nuclear Information System (INIS)

Goetze, Jens; Siedel, Heiner

2007-01-01

The present paper provides a methodology for the investigation and characterization of building sandstones. This analytical scheme was designed for distinguishing mature arenites, which in general show very similar properties and are difficult to distinguish. This is shown for Cretaceous sandstones from various occurrences in Saxony (Germany), which have been used for centuries as building materials. The procedure is mainly based on the combination of macroscopic rock description, thin section polarizing microscopy (phase composition, texture, grain-size distribution) and cathodoluminescence (CL) microscopy (quartz types, feldspar and kaolinite content) coupled with image analysis, scanning electron microscopy (accessories, pore cement, diagenetic grain surface features), and analysis of pore space data. Sometimes, additional data from X-ray diffraction or chemical analyses (major and trace elements) can be used. Especially in the case of quartz rich arenites, CL is a powerful tool for provenance analysis. The detailed analysis of sandstone material in most cases allows us to assign historically used building material to a specific sandstone occurrence. These results are important for both interpreting the weathering behaviour of the building material and the conservation, reconstruction and stone replacement of historical monuments

Porosity, petrophysics and permeability of the Whitby Mudstone (UK)

Science.gov (United States)

Houben, M.; Barnhoorn, A.; Hardebol, N.; Ifada, M.; Boersma, Q.; Douma, L.; Peach, C. J.; Bertotti, G.; Drury, M. R.

2016-12-01

Typically pore diameters in shales range from the µm down to the nm scale and the effective permeability of shale reservoirs is a function of the interconnectivity between the pore space and the natural fracture network present. The length and spacing of mechanical induced and natural fractures is one of the factors controlling gas produtivity from unconventional reservoirs. Permeability of the Whitby Mudstone measured on 1 inch cores was linked to microstructure and combined with natural fracture spacing present in outcrops along the Yorkshire coast (UK) to get insight into possible fluid pathways from reservoir to well. We used a combination of different techniques to characterize the porosity (gas adsorption, Scanning Electron Microscopy), mineralogy (X-Ray Fluorescence, X-Ray Diffraction, Scanning Electron Microscopy) and permeability (pressure step decay) of the Whitby Mudstone. In addition, we mapped the natural fracture network as present in outcrops along the Yorkshire coast (UK) at the 10-2-101m scale. Mineralogically we are dealing with a rock that is high in clay content and has an average organic matter content of about 10%. Results show a low porosity (max. 7%) as well as low permeability for the Whitby Mudstone. The permeability, measured parallel to bedding, depends on the confining pressure and is 86 nanodarcy at 10 MPa effective confining pressure and decreases to 16 nanodarcy at 40 MPa effective confining pressure. At the scale of observation the average distance to nearest natural fracture is in the order of 0.13 meter and 90 percent of all matrix elements are spaced within 0.4 meter to the nearest fracture. By assuming darcy flow, a permeability of 100 nanodarcy and 10% of overpressure we calculated that for the Whitby mudstone most of the gas resides in the matrix for less than 60 days until it reaches the fracture network.

Paleomagnetic and magnetic fabric studies of Lower Triassic red sandstones from the autochthonous cover of the Central Western Carpathians: new insights into paleogeographic setting and tectonic evolution of the area

Science.gov (United States)

Szaniawski, R.; Jankowski, L.; Ludwiniak, M.; Mazzoli, S.; Szczygieł, J.

2017-12-01

The Carpathian Mountains were formed through progressive collision and amalgamation of the Alcapa and Tisza-Dacia microplates with the European Platform. The Central Western Carpathians (CWC) tectonic unit analyzed in this study constitutes a fragment of the Alcapa microplate - research in this area is therefore of great importance in the context of the geotectonic evolution of the Carpathian orogen. Our paleomagnetic and magnetic fabric studies were focused on Lower Triassic red sandstones from the autochthonous cover of the crystalline basement. We present new results from three mountain massifs: Low Tatra, Velka Fatra and Strazovske Vrchy, comparing them with our earlier works performed in the Tatra Mts. Rockmagnetic studies reveal similar results in all four studied regions - the dominant ferromagnetic carrier in red sandstones is hematite, while the magnetic fabric is mostly controlled by paramagnetic minerals. AMS results outline a bedding parallel foliation and a tectonic lineation. This lineation lies in the bedding plane but is somewhat oblique to the present horizontal plane. The fact that the lineation is not exactly parallel to the strike of the beds is most likely due to multistage deformation: the lineation is related to bedding parallel shortening associated with the folding and thrusting stage, while present-day bedding attitude results at least partially from rotations associated with subsequent uplift and/or faulting. Paleomagnetic analysis indicate that hematite carrier records characteristic remanent component of high unblocking temperatures (680°C) and both normal (dominant) and reversed polarity. Paleomagnetic inclinations are similar to those expected from reference paleomagnetic data from the European Platform. Declination values are rather similar in all four studied areas and imply moderate counterclockwise rotations of the CWC. These results are incompatible with some of the previous paleomagnetic studies of younger rocks from the CWC

Effects of Pisha sandstone content on solute transport in a sandy soil.

Science.gov (United States)

Zhen, Qing; Zheng, Jiyong; He, Honghua; Han, Fengpeng; Zhang, Xingchang

2016-02-01

In sandy soil, water, nutrients and even pollutants are easily leaching to deeper layers. The objective of this study was to assess the effects of Pisha sandstone on soil solute transport in a sandy soil. The miscible displacement technique was used to obtain breakthrough curves (BTCs) of Br(-) as an inert non-adsorbed tracer and Na(+) as an adsorbed tracer. The incorporation of Pisha sandstone into sandy soil was able to prevent the early breakthrough of both tracers by decreasing the saturated hydraulic conductivity compared to the controlled sandy soil column, and the impeding effects increased with Pisha sandstone content. The BTCs of Br(-) were accurately described by both the convection-dispersion equation (CDE) and the two-region model (T-R), and the T-R model fitted the experimental data slightly better than the CDE. The two-site nonequilibrium model (T-S) accurately fit the Na(+) transport data. Pisha sandstone impeded the breakthrough of Na(+) not only by decreasing the saturated hydraulic conductivity but also by increasing the adsorption capacity of the soil. The measured CEC values of Pisha sandstone were up to 11 times larger than those of the sandy soil. The retardation factors (R) determined by the T-S model increased with increasing Pisha sandstone content, and the partition coefficient (K(d)) showed a similar trend to R. According to the results of this study, Pisha sandstone can successfully impede solute transport in a sandy soil column. Copyright © 2015 Elsevier Ltd. All rights reserved.

Measurement of geo electric and radon intensity on determination of potential area for ground water drilling at Lebeng Barat village, Pasongsongan, East Java

International Nuclear Information System (INIS)

I Gde Sukadana

2013-01-01

Lebeng Barat village, Pasongsongan sub-district is a village which has insufficient of fresh water, particularly in dry season. This region has a fairly dense population and equitable distribution of the population, therefore a sufficient supply of clean water for consumption and other needs are required. The purpose of study is to find out the ground-water potential zone in determination of exploration drilling points to develop ground-water’s well production. The methods used in this study as follow: Geological/hydrogeological mapping, measurement of radon intensity and geo-electric sounding survey with Schlumberger’s configuration. Exposed rocks within work areas can be classified into 5 (five) rocks unit, namely clay stone with intercalation of limestone unit, inter bedded of calcareous sandstone and limestone unit, mud stone unit and limestone-clay stone unit. The potential rock’s layer as aquifer is a layer of calcareous sandstone which has characteristic of pale yellow to brown, medium-coarse grained, sufficient permeability rocks (in the section exposed at the surface) include the limestone unit. Rock aquifers that serve on the bottom are included in inter bedded of calcareous sandstone and limestone unit. Potential points recommended for drilling exploration / production are the point of LBR-29 with the thickness of the aquifer 1 (shallower) 33.86 m and aquifer 2 (deeper) 23.72 m. (author)

Kaolinite Mobilisation in Sandstone

DEFF Research Database (Denmark)

Rosenbrand, Esther; Fabricius, Ida Lykke; Kets, Frans

2013-01-01

suggest that this effect is due to kaolinite clay mobilisation from the quartz grain surface; the mobilised particles subsequently plug the pore throats and reduce the permeability irreversibly. The expected hysteresis is observed when the salinity is reduced and increased; however, in contradiction...... the mobilised kaolinite particles either remain suspended and thereby increase the fluid viscosity, or form porous aggregates that can be destabilized by hydrodynamic forces. To address how the pore scale distribution of kaolinite relates to the permeability of the entire sample, we relate permeability...

Geophysical signature recognition of aquifuge and relatively impermeable interbed in ore-hosting sandstone layer at sandstone-type uranium deposit

International Nuclear Information System (INIS)

Zhao Xigang; Wu Hanning; Bai Guanjun; Zhu Huanqiao; Jia Heng

2006-01-01

Geophysical signature recognition of aquifuge and relatively impermeable interbed in ore-hosting aquifer has been carried out a Shihongtan uranium deposit by using comprehensive logging data. The spatial distribution of above aquifuge and impermeable interbed is discussed, and the relation of these layers to sandstone-type uranium deposit, and their impact to in-situ leach mining technology are discussed. It is suggested that the aquifuge and relatively impermeable interbed bring about significant effect to the formation of interlayer oxidation zone sandstone-type uranium deposit, as well as to in-situ leach mining of the deposit. (authors)

Flow-permeability feedbacks and the development of segregation pipes in volcanic materials

Science.gov (United States)

Rust, Alison

2014-05-01

(microns to 2 mm) to clasts of decimeters or greater. The vertical gas escape pipes are distinguished from the surrounding pyroclastic flow deposit by the lack of fine ash in the pipes; this missing ash was transported up out of the pyroclastic flow by gas flow, a process called elutriation. Laboratory experiments with beds of binary mixtures of spheres aerated through a porous plate at the base, demonstrate that the size ratio, density ratio, and proportions of the two populations of spheres all affect the pattern and efficiency of segregation. Decompaction of the upper portion of the bed separates the grains and thus facilitated the elutriation of the finer particles, which must be transported up through the spaces between the larger particles. A variety of segregation feature are found including pipes lacking fines that grow down from the top of the bed. These could be explained by channelizing of gas flow due to a feedback between local reduction in fines increasing the local permeability and gas velocity.

Temperature effect on microstructure and P-wave propagation in Linyi sandstone

International Nuclear Information System (INIS)

Sun, Hui; Sun, Qiang; Deng, Wenni; Zhang, Weiqiang; Lü, Chao

2017-01-01

Highlights: • Mass loss rate, P-wave velocity change rate and damage factor increase exponentially as temperatures rise. • The damage threshold temperature of sandstone samples is 300 °C and limit temperature is 900 °C. • P-wave velocity change rate of sandstone exhibits excellent linearity with mass loss rate. • Damage factor can be well expressed by mass loss rate. - Abstract: In order to study the effect of high temperature on the sandstone, scanning electron microscope (SEM) experiments and primary wave (P-wave) velocity tests have been carried out on sandstone specimens heated to different temperature. The results showed that: (1) the mass loss rate increases exponentially with the increase of temperature and reaches 2.97% at 900 °C; (2) the P-wave velocity change rate increases exponentially with the increase of temperature while there is some fluctuation before 500 °C; (3) the damage threshold temperature of sandstone samples is 300 °C and the limit temperature is 900 °C; (4) there is a good linear relationship between the mass loss rate and the P-wave velocity change rate, and the correlation coefficient (R) of the fitting line is 0.989; (5) the damage caused by high temperature can be reflected better by the mass loss rate than P-wave velocity change rate. The results obtained in this paper will be good for predicting the properties of sandstone when exposed to high temperature.

Geology and oil and gas assessment of the Fruitland Total Petroleum System, San Juan Basin, New Mexico and Colorado: Chapter 6 in Geology and Oil and Gas Assessment of the Fruitland Total Petroleum System, San Juan Basin, New Mexico and Colorado

Science.gov (United States)

Ridgley, J.L.; Condon, S.M.; Hatch, J.R.

2013-01-01

The Fruitland Total Petroleum System (TPS) of the San Juan Basin Province includes all genetically related hydrocarbons generated from coal beds and organic-rich shales in the Cretaceous Fruitland Formation. Coal beds are considered to be the primary source of the hydrocarbons. Potential reservoir rocks in the Fruitland TPS consist of the Upper Cretaceous Pictured Cliffs Sandstone, Fruitland Formation (both sandstone and coal beds), and the Farmington Sandstone Member of the Kirtland Formation, and the Tertiary Ojo Alamo Sandstone, and Animas, Nacimiento, and San Jose Formations.

Desalination of salt damaged Obernkirchen sandstone by an applied DC field

DEFF Research Database (Denmark)

Matyščák, Ondřej; Ottosen, Lisbeth M.; Rörig-Dalgaard, Inge

2014-01-01

Soluble salts are considered as one of the most common causes for decay of building materials. In the present work, an electrokinetic method for desalination of sandstones from a historic warehouse was tested. The sandstones claddings were removed from the warehouse during a renovation action...... in the stones, i.e. the present investigation faces more challenges relevant to a real desalination action. Experiments were conducted with two Obernkirchen sandstones from the same warehouse, but with different levels of salt concentrations and porosity. The investigation includes removal of the most common...... salts: chlorides, nitrates, sulphates. In the experimental setup the electrodes were placed in a clay poultice: a mixture of kaolinite, calcite and distilled water. An electric direct current (DC) field was applied to the sandstone.By applying 2mA for 5–11days it was possible to reduce the chloride...

Polyaxial stress-dependent permeability of a three-dimensional fractured rock layer

Science.gov (United States)

Lei, Qinghua; Wang, Xiaoguang; Xiang, Jiansheng; Latham, John-Paul

2017-12-01

A study about the influence of polyaxial (true-triaxial) stresses on the permeability of a three-dimensional (3D) fractured rock layer is presented. The 3D fracture system is constructed by extruding a two-dimensional (2D) outcrop pattern of a limestone bed that exhibits a ladder structure consisting of a "through-going" joint set abutted by later-stage short fractures. Geomechanical behaviour of the 3D fractured rock in response to in-situ stresses is modelled by the finite-discrete element method, which can capture the deformation of matrix blocks, variation of stress fields, reactivation of pre-existing rough fractures and propagation of new cracks. A series of numerical simulations is designed to load the fractured rock using various polyaxial in-situ stresses and the stress-dependent flow properties are further calculated. The fractured layer tends to exhibit stronger flow localisation and higher equivalent permeability as the far-field stress ratio is increased and the stress field is rotated such that fractures are preferentially oriented for shearing. The shear dilation of pre-existing fractures has dominant effects on flow localisation in the system, while the propagation of new fractures has minor impacts. The role of the overburden stress suggests that the conventional 2D analysis that neglects the effect of the out-of-plane stress (perpendicular to the bedding interface) may provide indicative approximations but not fully capture the polyaxial stress-dependent fracture network behaviour. The results of this study have important implications for understanding the heterogeneous flow of geological fluids (e.g. groundwater, petroleum) in subsurface and upscaling permeability for large-scale assessments.

The influence of slip velocity and temperature on permeability during and after high-velocity fault slip

Science.gov (United States)

Tanikawa, W.; Mukoyoshi, H.; Tadai, O.; Hirose, T.; Lin, W.

2011-12-01

Fluid transport properties in fault zones play an important role in dynamic processes during large earthquakes. If the permeability in a fault zone is low, high pore-fluid pressures caused by thermal pressurization (Sibson, 1973) or shear-induced compaction (Blanpied et al., 1992) can lead to an apparent reduction of fault strength. Changes in porosity and permeability of fault rocks within a fault zone during earthquakes and the subsequent progressive recovery of these properties may have a large influence on earthquake recurrence (Sleep and Blanpied, 1992). A rotary shear apparatus was used to investigate changes of fluid transport properties in a fault zone by real-time measurement of gas flow rates during and after shearing of hollow sandstone and granite cylinders at various slip rates. Our apparatus measures permeability parallel to the slip plane in both the slip zone and wall rocks. In all cases, permeability decreased rapidly with an increase of friction, but recovered soon after slip, reaching a steady state within several tens of minutes. The rate of reduction of permeability increased with increasing slip velocity. Permeability did not recover to pre-slip levels after low-velocity tests but recovered to exceed them after high-velocity tests. Frictional heating of gases at the slip surface increased gas viscosity, which increased gas flow rate to produce an apparent permeability increase. The irreversible permeability changes of the low-velocity tests were caused by gouge formation due to wearing and smoothing of the slip surface. The increase of permeability after high-velocity tests was caused by mesoscale fracturing in response to rapid temperature rise. Changes of pore fluid viscosity contributed more to changes of flow rate than did permeability changes caused by shear deformation, although test results from different rocks and pore fluids might be different. References Blanpied, M.L., Lockner, D.A., Byerlee, J.D., 1992. An earthquake mechanism

Characteristics and model of sandstone type uranium deposit in south of Songliao basin

International Nuclear Information System (INIS)

Yu Wenbin; Yu Zhenqing

2010-01-01

Through analyzing the uranium deposit tectonic environment, upper cretaceous sequence stratigraphy, depositional system, evolutionary characteristics of sand bodies, the effect of subsequent transformation and the characteristic of uranium deposit, the sandstone type uranium deposit in southern basin is different from typical interlayer oxidation zone sandstone type uranium deposit. The formation and evolution of sandstone-type uranium deposit are controlled by structure fensters; the favorable sedimentary facies type is braided river facies, and the ore body is braided river sand body. The size of uranium deposits is controlled by the local oxidation zone with the characteristics of sandstone type uranium deposit in partial oxidation zone. Uranium ore bodies which distribute in the roof wings of structure fenstes, and occur in gray layers between the upper and lower oxidation zone, showing tabular, and the plate of uranium ore body is controlled by the local oxidation zone. Based on the geological features of sandstone-type uranium deposits, the metallogenic model of local oxidation zones sandstone-type uranium deposits has been set up in the south of Songliao Baisn. (authors)

Distribution and nature of fault architecture in a layered sandstone and shale sequence: An example from the Moab fault, Utah

Science.gov (United States)

Davatzes, N.C.; Aydin, A.

2005-01-01

We examined the distribution of fault rock and damage zone structures in sandstone and shale along the Moab fault, a basin-scale normal fault with nearly 1 km (0.62 mi) of throw, in southeast Utah. We find that fault rock and damage zone structures vary along strike and dip. Variations are related to changes in fault geometry, faulted slip, lithology, and the mechanism of faulting. In sandstone, we differentiated two structural assemblages: (1) deformation bands, zones of deformation bands, and polished slip surfaces and (2) joints, sheared joints, and breccia. These structural assemblages result from the deformation band-based mechanism and the joint-based mechanism, respectively. Along the Moab fault, where both types of structures are present, joint-based deformation is always younger. Where shale is juxtaposed against the fault, a third faulting mechanism, smearing of shale by ductile deformation and associated shale fault rocks, occurs. Based on the knowledge of these three mechanisms, we projected the distribution of their structural products in three dimensions along idealized fault surfaces and evaluated the potential effect on fluid and hydrocarbon flow. We contend that these mechanisms could be used to facilitate predictions of fault and damage zone structures and their permeability from limited data sets. Copyright ?? 2005 by The American Association of Petroleum Geologists.

Real rock-microfluidic flow cell: A test bed for real-time in situ analysis of flow, transport, and reaction in a subsurface reactive transport environment.

Science.gov (United States)

Singh, Rajveer; Sivaguru, Mayandi; Fried, Glenn A; Fouke, Bruce W; Sanford, Robert A; Carrera, Martin; Werth, Charles J

2017-09-01

Physical, chemical, and biological interactions between groundwater and sedimentary rock directly control the fundamental subsurface properties such as porosity, permeability, and flow. This is true for a variety of subsurface scenarios, ranging from shallow groundwater aquifers to deeply buried hydrocarbon reservoirs. Microfluidic flow cells are now commonly being used to study these processes at the pore scale in simplified pore structures meant to mimic subsurface reservoirs. However, these micromodels are typically fabricated from glass, silicon, or polydimethylsiloxane (PDMS), and are therefore incapable of replicating the geochemical reactivity and complex three-dimensional pore networks present in subsurface lithologies. To address these limitations, we developed a new microfluidic experimental test bed, herein called the Real Rock-Microfluidic Flow Cell (RR-MFC). A porous 500μm-thick real rock sample of the Clair Group sandstone from a subsurface hydrocarbon reservoir of the North Sea was prepared and mounted inside a PDMS microfluidic channel, creating a dynamic flow-through experimental platform for real-time tracking of subsurface reactive transport. Transmitted and reflected microscopy, cathodoluminescence microscopy, Raman spectroscopy, and confocal laser microscopy techniques were used to (1) determine the mineralogy, geochemistry, and pore networks within the sandstone inserted in the RR-MFC, (2) analyze non-reactive tracer breakthrough in two- and (depth-limited) three-dimensions, and (3) characterize multiphase flow. The RR-MFC is the first microfluidic experimental platform that allows direct visualization of flow and transport in the pore space of a real subsurface reservoir rock sample, and holds potential to advance our understandings of reactive transport and other subsurface processes relevant to pollutant transport and cleanup in groundwater, as well as energy recovery. Copyright © 2017 Elsevier B.V. All rights reserved.

The sedimentology and uranium mineralization of the Klipbankskraal deposit north of Merweville, C.P

International Nuclear Information System (INIS)

Le Roux, J.P.

1982-08-01

A sedimentological study was conducted on the farm Klipbankskraal, north-west of Merweville. The orebody is located in the Poortjie Member at the base of the Teekloof Formation. The mineralised sandstone, S1, is a tabular lithosome deposited in an ephemeral, braided river environment. It consists of two major and several minor mesocycles, with the upper major cycle showing evidence of having inherited the drainage pattern of the lower mesocycle. The vector mean azimuth of the sequence as a whole is towards 059 degrees. The uranium is present as stacked, tabular lenses associated with permeable zones in the immediate vicinity of erosional inter-cycle contacts. Although no obvious relationship exists between the uranium and channels or bars, the distribution of plant material was controlled by the current velocities which also controlled the type of sedimentary structures. Uranium occurs preferentially in fissile-weathering (horizontal-bedded) sandstone and mud-pebble conglomerate, both permeable lithologies, and in mudstone or silt-stone. Uranium is genetically related to other elements such as Mn, Mo, Cu, Co and Pb, which must have been constituents of the ore fluid. Uraniferous granites in the source areas probaly supplied most of the uranium

Support vector regression to predict porosity and permeability: Effect of sample size

Science.gov (United States)

Al-Anazi, A. F.; Gates, I. D.

2012-02-01

Porosity and permeability are key petrophysical parameters obtained from laboratory core analysis. Cores, obtained from drilled wells, are often few in number for most oil and gas fields. Porosity and permeability correlations based on conventional techniques such as linear regression or neural networks trained with core and geophysical logs suffer poor generalization to wells with only geophysical logs. The generalization problem of correlation models often becomes pronounced when the training sample size is small. This is attributed to the underlying assumption that conventional techniques employing the empirical risk minimization (ERM) inductive principle converge asymptotically to the true risk values as the number of samples increases. In small sample size estimation problems, the available training samples must span the complexity of the parameter space so that the model is able both to match the available training samples reasonably well and to generalize to new data. This is achieved using the structural risk minimization (SRM) inductive principle by matching the capability of the model to the available training data. One method that uses SRM is support vector regression (SVR) network. In this research, the capability of SVR to predict porosity and permeability in a heterogeneous sandstone reservoir under the effect of small sample size is evaluated. Particularly, the impact of Vapnik's ɛ-insensitivity loss function and least-modulus loss function on generalization performance was empirically investigated. The results are compared to the multilayer perception (MLP) neural network, a widely used regression method, which operates under the ERM principle. The mean square error and correlation coefficients were used to measure the quality of predictions. The results demonstrate that SVR yields consistently better predictions of the porosity and permeability with small sample size than the MLP method. Also, the performance of SVR depends on both kernel function

Mechanism for calcite dissolution and its contribution to development of reservoir porosity and permeability in the Kela 2 gas field,Tarim Basin,China

Institute of Scientific and Technical Information of China (English)

2008-01-01

This study is undertaken to understand how calcite precipitation and dissolution contributes to depth-related changes in porosity and permeability of gas-bearing sandstone reservoirs in the Kela 2 gas field of the Tarim Basin, Northwestern China. Sandstone samples and pore water samples are col-lected from well KL201 in the Tarim Basin. Vertical profiles of porosity, permeability, pore water chem-istry, and the relative volume abundance of calcite/dolomite are constructed from 3600 to 4000 m below the ground surface within major oil and gas reservoir rocks. Porosity and permeability values are in-versely correlated with the calcite abundance, indicating that calcite dissolution and precipitation may be controlling porosity and permeability of the reservoir rocks. Pore water chemistry exhibits a sys-tematic variation from the Na2SO4 type at the shallow depth (3600-3630 m), to the NaHCO3 type at the intermediate depth (3630―3695 m),and to the CaCl2 type at the greater depth (3728―3938 m). The geochemical factors that control the calcite solubility include pH, temperature, pressure, Ca2+ concen-tration, the total inorganic carbon concentration (ΣCO2), and the type of pore water. Thermodynamic phase equilibrium and mass conservation laws are applied to calculate the calcite saturation state as a function of a few key parameters. The model calculation illustrates that the calcite solubility is strongly dependent on the chemical composition of pore water, mainly the concentration difference between the total dissolved inorganic carbon and dissolved calcium concentration (i.e., [ΣCO2] -[Ca2+]). In the Na2SO4 water at the shallow depth, this index is close to 0, pore water is near the calcite solubility. Calcite does not dissolve or precipitate in significant quantities. In the NaHCO3 water at the intermedi-ate depth, this index is greater than 0, and pore water is supersaturated with respect to calcite. Massive calcite precipitation was observed at this depth

Study on the water retention effect of compound soil of arsenic sandstone and sand under the condition of typical crop planting

Science.gov (United States)

Liu, S. Y.; Wang, N.; Xie, J. C.; Jiang, R. G.; Zhao, M. L.

2017-08-01

Arsenic sandstone is the main reason of soil erosion in the Mu Us Sandy Land, simultaneously was proved to be a kind of good water retaining agent. In order to provide references for the utilization of water and soil resources and the prevention and control of desertification and soil erosion of the southern margin of Mu Us Sandy Land, on the basis of earlier studies the farmland experiments of compound soil with three ratios of 1:1, 1:2 and 1:5 between arsenic sandstone and sand under maize planting patterns were designed, whose experimental process was divided into six stages according to the crop growth status. The results showed that the soil moisture content was highest in the layer of 0˜40cm where the compound soil mainly concentrated in, which was related to the potent water retention of arsenic sandstone and strong water permeability of undisturbed sandy soil. The variation coefficients in the soil of 1:1 and 1:2 were more stable and evenly distributed. The compound soil can effectively improve the soil water retention capacity, and prolong the storage time of soil water. Among them, water loss rate in soil of 1:1 and 1:2 were lower. The coefficient of variation also confirms that the water distributions of the two types of soil were more uniform and stable. Besides illustrating the effects of the soil amelioration measures on spatial and temporal variation of soil moisture content and the improvement of soil water regime, the study provides some references for the development and utilization of agriculture in Mu Us Sandy Land.

Aquifer prospect and vulnerability of Upper Maastrichtian sandstones: Case of Ajali and Nsukka formations in the Northern Enugu Province, southeastern Nigeria

Science.gov (United States)

Ukpai, Stephen N.; Ezeh, Hilary N.; Igwe, James O.

2017-11-01

Two typical aquifer systems, namely, regional aquifer and local Perched aquifer have been delineated in the study area. The regional aquifer was identified at about 100 m depth around lowland areas, although prone to polluting effects from farming activities, erosion and weathering processes. This study investigated extents of groundwater pollution and permeability of the aquifers from water sample and grain size analyses. Results show porosity ranging from 49 to 50% and hydraulic conductivities as follows: 7.0 m/day for the sandstone of Nsukka Formation, 34.6 m/day for the outcrop of Ajali sandstone and 10.4 m/day for the sandstone at saturated subsurface zone with transmissivity of about 572 m2/day. The results signify that the regional aquifer is recharged by substantial rate of infiltrations vis-a-vis surface outcrops, and is therefore vulnerable to infiltration of pollution plumes. The groundwater is mainly acidic at pH ranging from 5.05 to 7.41 with a mean value of about 6.48, hence the pollution from dissolved iron in many places. Three main water types were identified, namely, Ca-Mg-HCO3, Ca-HCO3-Cl2 and Mg-Na-HCO3-SO4-Cl2 facies, all signifying dominance of groundwater species arising from precipitation recharge. This has resulted in the influences of surface effluents from run off as indicated by nitrate pollution in some areas. Thus, active hydrologic cycle controls the chemical facies in the water resources of the region, and with its hydraulic influence on the landscape, the quality status of groundwater, as well as the growth of agricultural products have been impaired.

Combined tide and storm influence on facies sedimentation of miocene Miri Formation, Sarawak

International Nuclear Information System (INIS)

Yuniarta Ulfa; Nasiman Sapari; Zuhar Zahir Tuan Harith

2011-01-01

This study was conducted on the sedimentary rocks belonging to the Miri Formation (Middle - Late Miocene). The primary objective of the present study is to provide additional interpretation on the stratigraphy of the Miri Formation in the Miri Field based on the new information gathered from new outcrops in the area. Five outcrops were examined in detail on sedimentology and stratigraphy. Based on lithology, sedimentary structures, bedding geometry and traces fossil, the sediments of the Miri Formation were grouped into fourteen lithofacies. Influence of tide and storm during the depositional processes of the formation were indicated by the group of two main facies associations which are: (i) tide-dominated estuary; and (ii) wave-and-storm dominated facies associations. The tide-dominated estuary system of the Miri Formation are includes variety of sub environments: estuary mouth or tidal channel and sand bars (characterized by trough cross-stratified sandstone with mud drapes facies), estuary channel or upper flow regime of sand flat (characterized by parallel stratified sandstone with mud-laminas facies), mixed-tidal flat (characterized by wavy and flaser bedded sandstone facies), and mud-tidal flat (characterized by rhythmic stratified sandstone-mudstone and lenticular bedding facies). The wave-and-storm dominated varied from lower to middle shore face (characterized by hummocky cross-stratified sandstone and rhythmic parallel stratified sandstone and laminated siltstone facies), upper shore face (characterized by swaley cross-stratified sandstone), lower shore face inter bedded to bioturbated sandstone and siltstone facies), and offshore transitional (characterized by bioturbated sandstone and mudstone inter bedding with parallel to hummocky cross-stratified sandstone facies). (author)

Southeast Florida Sediment Assessment and Needs Determination (SAND) Study

Science.gov (United States)

2014-09-01

sand with some shell beds, sandstone , and limestone *Miami Limestone 0 to 80 ft Oolitic limestone, quartz sand, and sandstone Anastasia 0 to 100 ft...Sand, shell beds, marl, calcareous sandstone (coquina/calcarenite) Fort Thompson 0 to 80 ft Silty limestone, silty sand, clayey marl, shell marl...highly- to moderately- weathered quartzose sandstone , and highly-weathered (saprolitic) to moderately-weathered hard limestone. North-south and

GREYBULL SANDSTONE PETROLEUM POTENTIAL ON THE CROW INDIAN RESERVATION, SOUTH-CENTRAL MONTANA

Energy Technology Data Exchange (ETDEWEB)

David A. Lopez

2000-12-14

Evaluation of the Lower Cretaceous Greybull Sandstone on the Crow Indian Reservation for potential stratigraphic traps in the valley-fill sandstone was the focus of this project. The Crow Reservation area, located in south-central Montana, is part of the Rocky Mountain Foreland structural province, which is characterized by Laramide uplifts and intervening structural basins. The Pryor and Bighorn mountains, like other foreland uplifts, are characterized by asymmetrical folds associated with basement-involved reverse faults. The reservation area east of the mountains is on the northwestern flank of the Powder River Basin. Therefore, regional dips are eastward and southeastward; however, several prominent structural features interrupt these regional dips. The nearly 4,000 mi{sup 2} reservation is under explored but has strong potential for increased oil and gas development. Oil and gas production is well established in the Powder River Basin of Wyoming to the south as well as in the areas north and west of the reservation. However, only limited petroleum production has been established within the reservation. Geologic relations and trends indicate strong potential for oil and gas accumulations, but drilling has been insufficient for their discovery. The Greybull Sandstone, which is part of the transgressive systems tract that includes the overlying Fall River Sandstone, was deposited on a major regional unconformity. The erosional surface at the base of the Greybull Sandstone is the +100 Ma, late Aptian-Early Albian regional unconformity of Weimer (1984). This lowstand erosional surface was controlled by a basin-wide drop in sea level. In areas where incised Greybull channels are absent, the lowstand erosional unconformity is at the base of the Fall River Sandstone and equivalent formations. During the pre-Greybull lowstand, sediment bypassed this region. In the subsequent marine transgression, streams began to aggrade and deposit sand of the lower Greybull Sandstone

3D visualization of liquefaction-induced dune collapse in the Navajo Sandstone, Utah, USA

Science.gov (United States)

Ford, Colby; Nick, Kevin; Bryant, Gerald

2015-04-01

The eolian Navajo Sandstone outcrop on the Canyon Overlook Trail in Zion National Park in Southern Utah is dissected by modern erosion in a way which reveals a great deal of the three-dimensional architecture of a major soft-sediment deformation event. The feature is bounded below by a well-developed interdune complex made up of two superimposed carbonate lenses, above by an irregular truncational surface, and incorporates 3 - 10 m of sandstone over an approximately 2 km area. The material above the deformed interval is undeformed cross-bedded sandstone, with crossbeds downlapping onto the surface of truncation. The stratigraphic confinement of deformation and the irregularity of the upper bounding surface suggests a deformation process which created topography, which was in turn covered by the next upwind dune before it could be eroded flat. The deformed material itself is laterally segmented by a stacked succession of shear surfaces, which all strike approximately perpendicular to the paleo-wind direction and dip at decreasing angles in the down paleo-wind direction. These factors point to the collapse of a major dune into the downwind interdune area, likely initiated by liquefaction in the interdune complex. The foundering of the dune's toe into the liquefied area created a powerful lateral stress field which did not extend significantly into the subsurface. The dune collapse process has been used in the past to describe other soft-sediment deformation features in the Navajo Sandstone, but this site provides a wealth of physical details which were not previously associated with dune collapse. Shear surfaces originate in the interdune deposit as slip between laminae, then the cohesive muds provided support as they were thrust upward to angles of up to 50 degrees. The margins of the site also contain important paleoenvironmental indicators. Dinosaur tracks are exposed both at the extreme upwind and downwind margins of the interdune deposit in and slightly above

Mechanical changes caused by CO2-driven cement dissolution in the Morrow B Sandstone at reservoir conditions: Experimental observations

Science.gov (United States)

Wu, Z.; Luhmann, A. J.; Rinehart, A. J.; Mozley, P.; Dewers, T. A.

2017-12-01

Carbon Capture, Utilization and Storage (CCUS) in transmissive reservoirs is a proposed mechanism in reducing CO2 emissions. Injection of CO2 perturbs reservoir chemistry, and can modify porosity and permeability and alter mineralogy. However, little work has been done on the coupling of rock alteration by CO2 injection and the mechanical integrity of the reservoir. In this study, we perform flow-through experiments on calcite- and dolomite-cemented Pennsylvanian Morrow B Sandstone (West Texas, USA) cores. We hypothesize that poikilotopic calcite cement has a larger impact on chemo-mechanical alteration than disseminated dolomite cement given similar CO2 exposure. With one control brine flow-through experiment and two CO2-plus-brine flow-through experiments for each cement composition, flow rates of 0.1 and 0.01 ml/min were applied under 4200 psi pore fluid pressure and 5000 psi confining pressure at 71 °C. Fluid chemistry and permeability data enable monitoring of mineral dissolution. Ultrasonic velocities were measured pre-test using 1.2 MHz source-receiver pairs at 0.5 MPa axial load and show calcite-cemented samples with higher dynamic elastic moduli than dolomite-cemented samples. Velocities measured post-experiment will identify changes from fluid-rock interaction. We plan to conduct cylinder-splitting destructive mechanical test (Brazil test) to measure the pristine and altered tensile strength of different cemented sandstones. The experiments will identify extents to which cement composition and texture control chemo-mechanical degradation of CCUS reservoirs. Funding for this project is provided by the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL) through the Southwest Regional Partnership on Carbon Sequestration (SWP) under Award No. DE-FC26-05NT42591. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and Engineering Solutions of Sandia LLC, a wholly owned subsidiary of

Numerical simulation of roadway support in a sandstone-type uranium mine

International Nuclear Information System (INIS)

Liu Huipeng; Li Yu; Song Lixia

2009-01-01

At present, the most surrounding rocks of sandstone-type uranium mines in China are mudstone, sandstone, pelitic siltstone, and so on. They show the characteristics of soft rock. Such uranium deposit is not fit for in-situ leaching. If the uranium ores are mined by conventional mining method, one of the problems to be solved is the support technique in the soft rock roadway. So, taking a uranium mine in Inner Mongolia as the research object, the support technique in the soft rock roadway of the sandstone-type uranium deposits is studied. Through on-site engineering geological investigation and laboratory test, the main reasons for roadway damage are analyzed. A technique of support in the soft rock roadway of sandstone-type uranium deposits is put forward by drawing on the expericnce of soft rock roadway support in coal mines. The roadway shape and support parameters are optimized by using a numerical simulation method. The results verified the feasibility of the supporting technique. (authors)

High-resolution sequence stratigraphic character and sandstone-type uranium ore formation. A case from Saihan Formation in Baiyinwula area, Erlian Basin

International Nuclear Information System (INIS)

He Zhongbo; Qin Mingkuan

2006-01-01

High-resolution sequence stratigraphy has been applied widely in the petroleum exploration and development, many achievements have been achieved. However, it is in the beginning stage that high-resolution sequence stratigraphy is applied to explore the sandstone-type uranium deposits in Erlian Basin. By applying principles of high-resolution sequence stratigraphy and taking typical boreholes as an example, sedimentary cycles of Saihan Formation, the ore-bearing formation in Baiyinwula area are divided and correlated through cross sections. One long-term cycle (LSC 1 ), two middle-term cycles (MSC 1 , MSC 2 ) have been identified in this study. Based on this and combined with the mineralization character of sandstone uranium deposits in this area, it is presented that the interlayer oxidation zone is developed mainly in the rising hemicycle of MSC 1 and uranium ore bodies predominantly in channel sand bodies that were developed in the system tract with low accommodation; furthermore, it is recognized that these sand bodies are moderate (10-15 m) in thickness, fairly good in interconnectivity, relatively thin (<3 m) with the argillaceous interbed, and good in permeability, abundant in the organic matter and thus it is favorable for the development of the interlayer oxidization zone. (authors)

Traces of the heritage arising from the Macelj sandstone

Science.gov (United States)

Golež, Mateja

2014-05-01

The landscape of Southeast Slovenia and its stone heritage principally reveal itself through various Miocene sandstones. The most frequently found type on the borderline between Slovenia and Croatia, i.e. east of Rogatec, is the micaceous-quartz Macelj sandstone. This rock ranges in colour from greenish grey to bluish grey and yellowish, depending on the content of glauconite, which colours it green. In its composition, the rock is a heterogeneous mixture of grains of quartz, dolomite, muscovite, microcline, anorthite and glauconite. The average size of grains is 300μm. In cross-section, they are oblong, semi-rounded or round. The mechanical-physical and durability properties of the Macelj sandstone, which have been characterised pursuant to the applicable standards for natural stone, reveal that the rock exhibits poor resistance to active substances from the atmosphere, particularly in the presence of salt. In the surroundings of Rogatec, there are around 45 abandoned quarries of the Macelj sandstone, which are the result of the exploitation of this mineral resource from the 17th century on. The local quarrymen earned their bread until 1957, when the Kambrus quarry industry closed down. From the original use of this mineral resource as construction and decorative material, the useful value of the Macelj sandstone expanded during the development of the metals industry to the manufacture of large and small grindstones for the needs of the domestic and international market. Therefore, traces of quarrying can not only be seen in the disused quarries, but also in the rich architectural heritage of Rogatec and its surroundings, the stone furniture - from portals, window frames, wells, various troughs, pavements to stone walls - and other. The living quarrying heritage slowly passed into oblivion after World War II, although the analysis of the social image of the people residing in Rogatec and its surroundings revealed that there was an average of one stonemason in

Middle Ordovician brachiopods from the Stairway Sandstone, Amadeus Basin, central Australia

DEFF Research Database (Denmark)

Jakobsen, Kristian Grube; Brock, Glenn A.; Nielsen, Arne Thorshøj

2014-01-01

-water palaeoenvironment along the margin of northeastern Gondwana. The brachiopods from the Stairway Sandstone are of low diversity and represent ca 9% of the entire shelly fauna. Five brachiopod taxa are described from the Stairway Sandstone; all are endemic to the Amadeus Basin at species level. Two new species...

Application potential of sequence stratigraphy to prospecting for sandstone-type uranium deposit in continental depositional basins

International Nuclear Information System (INIS)

Li Shengxiang; Chen Zhaobo; Chen Zuyi; Xiang Weidong; Cai Yuqi

2001-01-01

Sequence stratigraphy has been widely used in hydrocarbon exploration and development, and great achievements have been achieved. However, its application to the prospecting for sandstone-type uranium deposits is just beginning. The metallogenic characteristics of sandstone-type uranium deposits and those of oil and gas are compared, and the relationship between sandstone-type uranium metallogenesis and the system tracts of sequence stratigraphy is studied. The authors propose that highest and system tracts are the main targets for prospecting interlayer oxidation zone type sandstone uranium deposits, and the incised valleys of low stand system tracts are favourable places for phreatic oxidation zone type sandstone uranium deposits, and transgressive system tracts are generally unfavorable to the formation of in-situ leachable sandstone-type uranium deposits. Finally, the authors look ahead the application potential of sequence stratigraphy to the prospecting for sandstone-type uranium deposits in continental depositional basins

Simulation of aquifer tests and ground-water flowpaths at the local scale in fractured shales and sandstones of the Brunswick Group and Lockatong Formation, Lansdale, Montgomery County, Pennsylvania

Science.gov (United States)

Goode, Daniel J.; Senior, Lisa A.

2000-01-01

The U.S. Geological Survey, as part of technical assistance to the U.S. Environmental Protection Agency, has constructed and calibrated models of local-scale ground-water flow in and near Lansdale, Pa., where numerous sources of industrial contamination have been consolidated into the North Penn Area 6 Superfund Site. The local-scale models incorporate hydrogeologic structure of northwest-dipping beds with uniform hydraulic properties identified in previous studies. Computations associated with mapping the dipping-bed structure into the three-dimensional model grid are handled by a preprocessor using a programmed geographic information system (GIS). Hydraulic properties are identified by calibration of the models using measured water levels during pumping and recovery from aquifer tests at three sites. Reduced flow across low-permeability beds is explicitly simulated. The dipping high-permeability beds are extensive in the strike direction but are of limited extent in the dip direction. This model structure yields ground-water-flow patterns characteristic of anisotropic aquifers; preferred flow is in the strike direction. The transmissivities of high-permeability beds in the local-scale models range from 142 to 1,900 ft2/d (feet squared per day) (13 to 177 m2/d). The hydraulic conductivities of low-permeability parts of the aquifer range from 9.6 x 10-4 to 0.26 ft/d (feet per day) (2.9 x 10-4 to 0.079 m/d). Storage coefficients and specific storage are very low, indicating the confined nature of the aquifer system. The calibrated models are used to simulate contributing areas of wells under alternative, hypothetical ground-water-management practices. Predictive contributing areas indicate the general characteristics of ground-water flow towards wells in the Lansdale area. Recharge to wells in Lansdale generally comes from infiltration near the well and over an area that extends upgradient from the well. The contributing areas for two wells pumping at 10 gal

Developments in permeable and low permeability barriers

International Nuclear Information System (INIS)

Jefferis, S.A.; Norris, G.H.; Thomas, A.O.

1997-01-01

The concept of the reactive treatment zone whereby pollutants are attenuated as they move along a pathway in the ground has enabled a re-thinking of many of the concepts of containment. In particular it offers the potential for the control of the flux from a contaminated area by controlling the contaminant concentration in the pathway(s) as well as or instead of using a low permeability barrier. The paper outlines the basic concepts of the reactive treatment zone and the use of permeable and low permeability reactive systems. The paper then gives a case history of the installation of a permeable barrier using an in-situ reaction chamber

Physical Property Changes During CO2 Injection into Sandstone from Pukpyeong Formation, South Korea: Pore-scale Approach

Science.gov (United States)

Han, J.; Keehm, Y.

2010-12-01

Carbon dioxide is believed to be responsible for global warming and climate change, and Korea government puts a great effort in CCS (Carbon Capture and Storage). The geological sequestration is regarded as one viable option and we are looking for prospecting formations for carbon storage. In this paper, we present a new approach to determine physical property changes during CO2 injection and preliminary results from applying the method to one of prospective Tertiary formation in South Korea. The so-called computational rock physics method is composed of three steps: 1) acquisition of high-resolution pore microstructures by X-ray micro-tomography; 2) CO2 injection simulation using lattice-Boltzmann (LB) two-phase flow simulation; and 3) FEM property simulations (electrical and elastic) at different CO2 saturations during the injection. We have been shown the viability of the method last year. This year we applied this method to one of CS (carbon storage) target area, Pukpyeong formation located in north-eastern part of South Korea. From thin section analysis, we found that the formation is composed of mudstone, sandstone and conglomerate, and most of them are poorly consolidated. The mudstone and poorly-sorted conglomerate are believed to have very low permeability, and the effect of CO2 injection would be significant. Thus we focus on sandstone units and get pore microstructure of those units. We then performed the computational rock physics analysis, and present the relations of Vp - CO2 saturation, and electrical conductivity - CO2 saturation for a few sand units. We also present the preliminary upscaling results by putting combined sandstone and mudstone units into FEM modeling. The modeling results implies that the new computational approach can be very useful to characterizing the CS sites especially in early stage. Acknowledgement: This work was supported by the Energy R&D program of the Korea Institute of Energy Technology Evaluation and Planning (KETEP

Discussion on metallogenic prospect of sandstone-type uranium deposit in Yabulai basin

International Nuclear Information System (INIS)

Wang Lianshe; Li Xiangping

2003-01-01

Based on characteristics of initial basin type and tectonic reworking process, this article analyses the distribution features of depositional system and subsequent alteration of the target horizon of sandstone-type uranium deposits in Yabulai basin. Guided by prognostic criteria of sandstone-type uranium deposits, authors suggest that the post-depositional tectonic reworking in the basin was quite intense, and uranium metallogenic prospects are unfavorable. However, the Lower Cretaceous in the paleo-slope at the middle of the basin does show certain metallogenic prospects for sandstone-type uranium deposits

Facies distribution, depositional environment, and petrophysical features of the Sharawra Formation, Old Qusaiba Village, Central Saudi Arabia

Science.gov (United States)

Abbas, Muhammad Asif; Kaminski, Michael; Umran Dogan, A.

2016-04-01

moderate-scale transgressive episodes, while the thin shale interbeds in the middle and upper part of the Sharawra Formation represent small-scale transgressions. Overall, the Sharawra Formation contains a series of repetitive transgressive and regressive events and has been interpreted as a pro-deltaic deposit in previous studies. In the present study, the lowermost sandstone thickly bedded facies lie within the transition zone environment. The siltstone facies and the horizontally stratified facies show a middle shore face environment. The middle shore face environment is present locally. The bioturbation in the uppermost facies is indicative of the upper shore face environment. The porosity values do not vary much, as the average porosity for the sandstone facies is about 15%, for the siltstones it ranges about 7%. The permeability is variable throughout the formation, the values range from 50 to 300 md. Although sandstone has a good porosity and permeability, the siltstone facies exhibit poor petrophysical characteristics. In terms of reservoir characterization, the mineralogical mature, moderately well sorted top most sandstone facies, with appreciable porosity and permeability can be considered as a potential reservoir rock. This study has provided a base for future quantitative studies in this important formation in the area.

Effect of retrograde gas condensate in low permeability natural gas reservoir; Efeito da condensacao retrograda em reservatorios de gas natural com baixa permeabilidade

Energy Technology Data Exchange (ETDEWEB)

Chang, Paulo Lee K.C. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Faculdade de Engenharia Mecanica; Ligero, Eliana L.; Schiozer, Denis J. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Faculdade de Engenharia Mecanica. Dept. de Engenharia de Petroleo

2008-07-01

Most of Brazilian gas fields are low-permeability or tight sandstone reservoirs and some of them should be gas condensate reservoir. In this type of natural gas reservoir, part of the gaseous hydrocarbon mixture is condensate and the liquid hydrocarbon accumulates near the well bore that causes the loss of productivity. The liquid hydrocarbon formation inside the reservoir should be well understood such as the knowledge of the variables that causes the condensate formation and its importance in the natural gas production. This work had as goal to better understanding the effect of condensate accumulation near a producer well. The influence of the porosity and the absolute permeability in the gas production was studied in three distinct gas reservoirs: a dry gas reservoir and two gas condensate reservoirs. The refinement of the simulation grid near the producer well was also investigated. The choice of simulation model was shown to be very important in the simulation of gas condensate reservoirs. The porosity was the little relevance in the gas production and in the liquid hydrocarbon formation; otherwise the permeability was very relevant. (author)

Multidisciplinary studies on ancient sandstone quarries of Western Sardinia (Italy).

Science.gov (United States)

Grillo, Silvana Maria; Del Vais, Carla; Naitza, Stefano

2013-04-01

The ancient coastal quarries of Mediterranean are increasingly considered geosites of multidisciplinary relevance. They are sites of historical-archaeological interest that show ancient techniques of stone extraction; they are significant for cultural heritage conservation and restoration, as sources of the stones used in ancient buildings and monuments; they are sites of geological relevance, as often retain important stratigraphic sections; they are also useful markers of secular changes in the sea level. A multisciplinary study is in progress on the ancient quarries of the Sinis region (western Sardinia island), integrating archaeological, geological, minero-petrographical data. In Sardinia, coastal quarries have been established from Punic and Roman times. Many of them exploited Quaternary sediments along the southern and western coasts of the island. They consist of middle-late Pleistocene marine conglomerates and carbonate sandstones, and of coastal (aeolian) carbonate sandstones. Sandstone blocks of different sizes have been widely used in ancient cities for buildings, defensive works, harbours, etc. Three main areas of stone extraction (San Giovanni di Sinis, Punta Maimoni, Is Arutas) have been so far recognized in the Sinis. GIS-supported mapping and documentation of the sites includes their geology and stratigraphy, the extension and layout of the quarries, and an evaluation of volumes of extracted rocks. Documented archaeological evidences include ancient extraction fronts, spoil heaps, working areas, working traces in the old fronts, transport routes of blocks, and traces of loading facilities. The study is aimed at reconstructing the relationships of the quarries with the urban areas of Sinis, as the ancient Punic-Roman city of Tharros. Consequently, a minero-petrographical characterization (optical microscopy, XRD) is performed on sandstones sampled in each quarry, and in historical buildings in Tharros and other centres of the region (Cabras

Low resistivity and permeability in actively deforming shear zones on the San Andreas Fault at SAFOD

Science.gov (United States)

Morrow, Carolyn A.; Lockner, David A.; Hickman, Stephen H.

2015-01-01

The San Andreas Fault Observatory at Depth (SAFOD) scientific drillhole near Parkfield, California crosses the San Andreas Fault at a depth of 2.7 km. Downhole measurements and analysis of core retrieved from Phase 3 drilling reveal two narrow, actively deforming zones of smectite-clay gouge within a roughly 200 m-wide fault damage zone of sandstones, siltstones and mudstones. Here we report electrical resistivity and permeability measurements on core samples from all of these structural units at effective confining pressures up to 120 MPa. Electrical resistivity (~10 ohm-m) and permeability (10-21 to 10-22 m2) in the actively deforming zones were one to two orders of magnitude lower than the surrounding damage zone material, consistent with broader-scale observations from the downhole resistivity and seismic velocity logs. The higher porosity of the clay gouge, 2 to 8 times greater than that in the damage zone rocks, along with surface conduction were the principal factors contributing to the observed low resistivities. The high percentage of fine-grained clay in the deforming zones also greatly reduced permeability to values low enough to create a barrier to fluid flow across the fault. Together, resistivity and permeability data can be used to assess the hydrogeologic characteristics of the fault, key to understanding fault structure and strength. The low resistivities and strength measurements of the SAFOD core are consistent with observations of low resistivity clays that are often found in the principal slip zones of other active faults making resistivity logs a valuable tool for identifying these zones.

Crustal permeability

Science.gov (United States)

Gleeson, Tom; Ingebritsen, Steven E.

2016-01-01

Permeability is the primary control on fluid flow in the Earth’s crust and is key to a surprisingly wide range of geological processes, because it controls the advection of heat and solutes and the generation of anomalous pore pressures.  The practical importance of permeability – and the potential for large, dynamic changes in permeability – is highlighted by ongoing issues associated with hydraulic fracturing for hydrocarbon production (“fracking”), enhanced geothermal systems, and geologic carbon sequestration.  Although there are thousands of research papers on crustal permeability, this is the first book-length treatment.  This book bridges the historical dichotomy between the hydrogeologic perspective of permeability as a static material property and the perspective of other Earth scientists who have long recognized permeability as a dynamic parameter that changes in response to tectonism, fluid production, and geochemical reactions. 

Characteristics of isotope geology of sandstone-type uranium deposit in Turpan-Hami Basin

International Nuclear Information System (INIS)

Liu Hanbin; Xia Yuliang; Lin Jinrong; Fan Guang

2003-01-01

This paper expounds the isotope characteristics of in-situ leachable sandstone-type uranium deposit of Shihongtan in the southwestern part of Turpan-Hami basin. The results suggest that uranium mineralization age of 48 ± 2 Ma and 28 ± 4 Ma are obtained. The ages of the porphyritic granite and gneissic granite from the southwestern area are 422 ± 5 Ma and 268 ± 23 Ma. The U-Pb age of clastic zircons from ore-bearing sandstone is 283 ± 67 Ma, which is corresponding to the age of gneissic granite of the provenance area indicating the material source of uraniferous sandstone.Based. The sources are uraniferous sandstone accumulated during the deposition and the uranium leached from provenance area rocks by weathering. (authors)

Applying reaction condition index to predict sandstone type uranium deposit

International Nuclear Information System (INIS)

Chen Gongxin; Liu Jinhui; Cheng Hai

2002-01-01

On the basic of the explanation of reaction condition index, the deduction of reaction condition index calculation principle, the hydrogeological setting in Gongpoquan basin in Baishan, Gansu province and the study of reaction condition index of its water source point, the north Luotuoquan area in Gongpoquan basin seems to be a favourable place for sandstone type uranium deposit, and the prospect area for sandstone type uranium deposit is delimitated

Models for dryout in debris beds. Review and application to the analysis of PAHR

International Nuclear Information System (INIS)

Yamakoshi, Yoshinori

2000-03-01

There are many models for dryout in debiris beds and various conditions under which these models are applicable. For a reliable analysis of post-accident heat removal (PAHR), it is important that characteristics and applicability of each model should be made clear. In this report, formulation of the models for dryout and applicability of them are studied through comparing with experimental data. A new model for dryout prediction is also discussed here. It is difficult to predict the dryout power especially for a relatively shallow bed using a conventional model for channeled beds. The new model, which is based on the one-dimensional model derived by Lipinski, has permeability of channels in the governing equation, and enables us to predict the dryout power for relatively shallow beds. The following conclusions are derived from comparing the predicted dryout power with experimental data. The model for series heat removal is applicable to a packed bed while the DEBRIS-MD underestimates the dryout power for it. Either the original model assuming channel formation on the top of the bed or the modified model is applicable to a relatively deep bed with channels. For a relatively shallow bed with channels, the dryout power predicted by the modified model agrees with the experimental data in comparison with other models. (author)

Road drainage system using highly compressible and long-term permeable geotextile. Evaluation of long-term permeability and application to trafficability in a tunnel; Kotaiatsu mezumari taikyugata geotextile haisuizai wo mochiita roban haisui taisaku. Mezumari taikyusei no hyoka to tunnel konai kasetsu doro no trafficability kaizen koka

Energy Technology Data Exchange (ETDEWEB)

Takahashi, S.; Yamagishi, K.; Hirama, K.; Ueno, T. [Obayashi Corp., Tokyo (Japan)

1998-07-10

A geotextile drainage material called ART-DRAIN has been developed. It was applied to temporary roads in a tunnel, to evaluate its permeability through a long-term permeability test using a model. The ART-DRAIN is a drainage material for protecting the roads from muddy conditions in a tunnel due to spring water. A filter for permeating fine soil particles was employed to keep the permeability. From the long-term permeability test using a model, appropriate permeability of ART-DRAIN was maintained for three years without blinding. There was only a slight inflow of fine grain soils into the ART-DRAIN. It was confirmed that the permeability was not obstructed by the fine grain soils. The ART-DRAIN was applied to tunnel construction works for the high-speed railway in Kyoto and the national road in mountains. From these applications, factors for enhancing the permeability effect were confirmed, which includes the selection of high quality muck, insurance of the road-bed strength by the initial compaction, use of road drainage materials with high compressible property and permeability of filter, and intervals of drainage. 1 ref., 19 figs., 1 tab.

Facies analysis, sedimentology and paleocurrent of the quaternary nenering formation, Pengkalan Hulu, Malaysia

International Nuclear Information System (INIS)

Yuniarti Ulfa; Evonne Hooi Rong Yu; Ooi Cheng Kit

2014-01-01

Nenering Formation is essentially made up of semi-consolidated sediments, which are divided into basal conglomerate beds, conglomeratic sandstone, cross-bedded sandstone, and siltstone to muddy layers facies. It is overlie unconformable to the Berapit Formation, but conformable to the Kroh and Grik Formations. The stratigraphy of Nenering Formation is a fining upwards sequence where the thickness of conglomerate beds become thinner upwards and become thicker for conglomeratic sandstone. The thickness varies from 0.5 m to tenths of meters. The more sandy in the upper portion (cross-bedded sandstone) overlie with thin siltstone and mud stone facies. The clast and grain composition suggested that the material making up the sedimentary sequence were derived predominantly from the erosion of granitoid rocks and sedimentary and metamorphic rocks constitute a minor provenance. Imbrications and the trend sizes of clasts indicate that the paleo-current flow toward northeast. Cross bedding that was found in conglomerate and sandstone indicates the main channel depositional environment. The sequence stratigraphy of this area match with the Saskatchewan fluvial braided channel model. (author)

Outcrop analogue study of Permocarboniferous geothermal sandstone reservoir formations (northern Upper Rhine Graben, Germany): impact of mineral content, depositional environment and diagenesis on petrophysical properties

Science.gov (United States)

Aretz, Achim; Bär, Kristian; Götz, Annette E.; Sass, Ingo

2016-07-01

oil and acidic waters led to the dissolution of haematite cements in the lower Permocarboniferous formations. During the Eocene, subsidence of the Upper Rhine Graben porosities and permeabilities of the sandstones of these formations were strongly reduced to 2.5 % and 3.2 × 10-18 m2. The second important influence on reservoir quality is the distinct depositional environment and its influence on early diagenetic processes. In early stage diagenesis, the best influence on reservoir properties exhibits a haematite cementation. It typically occurs in eolian sandstones of the Kreuznach Formation (Upper Permocarboniferous) and is characterized by grain covering haematite coatings, which are interpreted to inhibit cementation, compaction and illitization of pore space during burial. Eolian sandstones taken from outcrops and reservoir depths exhibit the highest porosities (16.4; 12.3 %) and permeabilities (2.0 × 10-15; 8.4 × 10-16 m2). A third important influence on reservoir quality is the general mineral composition and the quartz content which is the highest in the Kreuznach Formation with 73.8 %. Based on the integrated study of depositional environments and diagenetic processes, reservoir properties of the different Permocarboniferous formations within the northern Upper Rhine Graben and their changes with burial depth can be predicted with satisfactory accuracy. This leads to a better understanding of the reservoir quality and enables an appropriate well design for exploration and exploitation of these geothermal resources.

Sedimentological Characteristics and Re-interpretation of the Paleoenvironment of Lokoja Sandstone, Southern Bida Basin, Nigeria

International Nuclear Information System (INIS)

Ojo, O. J.; Akande, S. O.

2002-01-01

Detail mapping of the Lokoja Formation consisting predominantly of sandstones exposed along Okene-Abuja highway near the confluence of Rivers Niger and Benue in the southern Bida Basin was undertaken in an attempt to reconstruct their depositional history. The analyses of the lithofacies characteristics, pebble morphogenesis and ichnofossil content of the Lokoja sandstones in the study area reveal their depositional environments which evolved from alluvial fans through braided stream into nearshore shallow marine conditions. The massive, immature, matrix to grain supported conglomerate subfacies can be interpreted as debris flow. The conglomeratic sandstone facies (massive, cross stratified and graded subfacies) reflect deposits of deep braided channels. The bioturbated and herringbone cross stratified conglomeratic sandstones indicate shallowing to marginal marine environments. The fine to medium grained sandstones, siltstones and claystones are interpreted as channel bars and floodplain deposits.Results of pebble morphogenesis analysis indicate predominance of fluvial processes. Minor high energy (probably beach) condition is indicated by some individual clasts from the conglomeratic sandstone facies with sphericity and OP index values less that 0.66 and -1.5 respectively.The study is significant because it represents the first sedimentological evidence of influence of shallow marine in the development of Lokoja sandstones during Campanian-Maastrichtian times

PALEOEVIRONMENT OF NIGERIA'S AJALI SANDSTONES: A ...

African Journals Online (AJOL)

The Ajali Sandstone is a major clastic formation of Campanian-Maastrichtian age occuring within the Anambra Basin, Southeastern Nigeria. ... The result is in line with earlier conclusions of fluvial or fluviodeltaic depositional environment based on analysis of faceis, sedimentary rock which are suitable for morphometrical ...

Fluid Flow through Porous Sandstone with Overprinting and Intersecting Geological Structures of Various Types

Science.gov (United States)

Zhou, X.; Karimi-Fard, M.; Durlofsky, L.; Aydin, A.

2010-12-01

Impact of a wide variety of structural heterogeneities on fluid flow in an aeolian sandstone in the Valley of Fire State Park (NV), such as (1) dilatant fractures (joints), (2) shear fractures (faults), and (3) contraction/compaction structures (compaction bands), are considered. Each type of these structures has its own geometry, spacing, distribution, connectivity, and hydraulic properties, which either enhance or impede subsurface fluid flow. Permeability of these structures may, on average, be a few orders of magnitude higher or lower than those of the corresponding matrix rocks. In recent years, the influence of a single type of these heterogeneities on fluid flow has been studied individually, such as joints, compaction bands or faults. However, as different types of geological structures are commonly present together in the same rock volume, their combined effect requires a more detailed assessment. In this study, fluid flow simulations are performed using a special finite-volume discretization technique that was developed by Karimi-Fard et al. (2004; 2006). Using this approach, thin features such as fractures and compaction bands are represented as linear elements in unstructured 2D models and as planar elements in 3D models, which significantly reduces the total number of cells and simplifies grid generation. The cell geometric information and the cell-to-cell transmissibility obtained from this discretization technique are input to Stanford’s General Purpose Research Simulator (GPRS) for fluid flow simulation. To account for the effects of the various geological structures on subsurface flow, we perform permeability upscaling over regions corresponding to large-scale simulation grid blocks in order to obtain equivalent permeability components in two principal directions. We will focus on the following problems: (1) compaction bands of multisets; (2) compartmentalization of compaction bands of high-angle, low-angle and horizontal; (3) joints overprinting

Storing in clay beds? What about research advancement?

International Nuclear Information System (INIS)

Lebon, P.

2006-01-01

The concept of underground disposal of toxic or radioactive materials is based on the idea that some geologic formations are capable to ensure the confinement of waste packages over very long periods of time by limiting the water influx towards the toxic elements and by fixing up those in solution. This paper presents the state-of-the-art about the researches on manufactured clays (nature, properties and conditioning) and about the researches on clay beds with the example of the Meuse/Haute-Marne (France) underground laboratory (geologic history, lithology, permeability, rock mechanics). (J.S.)

The Bentheim Sandstone: Geology, petrophysics, varieties and it's use as dimension stone

NARCIS (Netherlands)

Dubelaar, C.W.; Nijland, T.G.

2014-01-01

The shallow-marine Bentheim Sandstone was deposited in one of the NW-SE trending basins north of the London-Brabant and Rhenish massifs during the Valanginian (Early Cretaceous). The Bentheim Sandstone forms an important reservoir rock for petroleum, but has also proven itself as a very durable

On the water saturation calculation in hydrocarbon sandstone reservoirs

Energy Technology Data Exchange (ETDEWEB)

Stalheim, Stein Ottar

2002-07-01

The main goal of this work was to identify the most important uncertainty sources in water saturation calculation and examine the possibility for developing new S{sub w} - equations or possibility to develop methods to remove weaknesses and uncertainties in existing S{sub w} - equations. Due to the need for industrial applicability of the equations we aimed for results with the following properties: The accuracy in S{sub w} should increase compared with existing S{sub w} - equations. The equations should be simple to use in petrophysical evaluations. The equations should be based on conventional logs and use as few as possible input parameters. The equations should be numerical stable. This thesis includes an uncertainty and sensitivity analysis of the most common S{sub w} equations. The results are addressed in chapter 3 and were intended to find the most important uncertainty sources in water saturation calculation. To increase the knowledge of the relationship between R{sub t} and S{sub w} in hydrocarbon sandstone reservoirs and to understand how the pore geometry affects the conductivity (n and m) of the rock a theoretical study was done. It was also an aim to examine the possibility for developing new S{sub w} - equations (or investigation an effective medium model) valid inhydrocarbon sandstone reservoirs. The results are presented in paper 1. A new equation for water saturation calculation in clean sandstone oil reservoirs is addressed in paper 2. A recommendation for best practice of water saturation calculation in non water wet formation is addressed in paper 3. Finally a new equation for water saturation calculation in thinly interbedded sandstone/mudstone reservoirs is presented in paper 4. The papers are titled: 1) Is the saturation exponent n a constant. 2) A New Model for Calculating Water Saturation In 3) Influence of wettability on water saturation modeling. 4) Water Saturation Calculations in Thinly Interbedded Sandstone/mudstone Reservoirs. A

Preliminary study on features of mineralogical zoning of epigenetic alteration at sandstone-type uranium deposit, Dongsheng area, Ordos basin

International Nuclear Information System (INIS)

Xiao Xinjian; Li Ziying; Chen Anping

2004-01-01

Sandstone-type uranium deposits located in Dongsheng area, northern Ordos basin, occur in Zhiluo Formation, Middle Jurassic. The Zhiluo Formation is divided into two members. The lower member is further divided into two submembers. The lower submember is dominantly composed of grey sandstone being the ore-hosting horizon; the upper submember consists of grey-green sandstone and mudstone. The upper member of Zhiluo Formation is made of mottled medium-fine grained sandstone and mudstone. Through the microscopic observation and study on sandstones of Zhiluo Formation, authors have established a vertical zonation of epigenetic alteration (from the top to the bottom): the limonitization + clayization + carbonation in the mottled fine-grained sandstone of the upper member of Zhiluo Formation; the green alteration (II) (mainly the chloritization of biotite, as well as the chloritization and epidotization of feldspar) + clayization + carbonation in the grey-green sandstone of the upper submember of the lower member of Zhiluo Formation; and the green alteration (I) (mainly the epidotization of feldspar) + carbonation in grey, grey-white sandstone of the lower submember. The epigenetic alteration basically occurs in grey-green sandstone. The sandstone shows grey-green color because it contains much green biotite (not chlorite). The epigenetic alteration in sandstone layer is closely associated with the uranium ore-formation

Numerical simulation of coupled binary gas-solid interaction during carbon dioxide sequestration in a coal bed

International Nuclear Information System (INIS)

Feng Qiyan; Zhou Lai; Chen Zhongwei; Liu Jishan

2008-01-01

Complicated coupled binary gas-solid interaction arises during carbon dioxide sequestration in a coal seam, which combines effects of CO 2 -CH 4 counter adsorption, CO 2 -CH 4 counter diffusion, binary gas flow and coal bed deformation. Through solving a set of coupled field governing equations, a novel full coupled Finite Element (FE) model was established by COMSOL Multiphysics. The new FE model was applied to the quantification of coal porous pressure, coal permeability, gas composition fraction and coal displacement when CO 2 was injected in a CH 4 saturated coal bed. Numerical results demonstrate that CH 4 is swept by the injected CO 2 accompanied by coal volumetric deformation. Compared to the single CH 4 in situ, CH 4 -CO 2 counter-diffusion induced coal swelling can make more compensation for coal shrinkage due to effective stress. Competing influences between the effective stress and the CH 4 -CO 2 counter-diffusion induced volume change governs the evolution of porous pressure and permeability, which is controlled by the porous pressure correspondingly. This achievement extends our ability to understand the coupled multi-physics of the CO 2 geological sequestration and CO 2 enhanced coal bed methane recovery under field conditions. (authors)

Damage evaluation on oil-based drill-in fluids for ultra-deep fractured tight sandstone gas reservoirs

Directory of Open Access Journals (Sweden)

Jinzhi Zhu

2017-07-01

Full Text Available In order to explore the damage mechanisms and improve the method to evaluate and optimize the performance of formation damage control of oil-based drill-in fluids, this paper took an ultra-deep fractured tight gas reservoir in piedmont configuration, located in the Cretaceous Bashijiqike Fm of the Tarim Basin, as an example. First, evaluation experiments were conducted on the filtrate invasion, the dynamic damage of oil-based drill-in fluids and the loading capacity of filter cakes. Meanwhile, the evaluating methods were optimized for the formation damage control effect of oil-based drill-in fluids in laboratory: pre-processing drill-in fluids before grading analysis; using the dynamic damage method to simulate the damage process for evaluating the percentage of regained permeability; and evaluating the loading capacity of filter cakes. The experimental results show that (1 oil phase trapping damage and solid phase invasion are the main formation damage types; (2 the damage degree of filtrate is the strongest on the matrix; and (3 the dynamic damage degree of oil-based drill-in fluids reaches medium strong to strong on fractures and filter cakes show a good sealing capacity for the fractures less than 100 μm. In conclusion, the filter cakes' loading capacity should be first guaranteed, and both percentage of regained permeability and liquid trapping damage degree should be both considered in the oil-based drill-in fluids prepared for those ultra-deep fractured tight sandstone gas reservoirs.

Predicting flow through low-permeability, partially saturated, fractured rock: A review of modeling and experimental efforts at Yucca Mountain

International Nuclear Information System (INIS)

Eaton, R.R.; Bixler, N.E.; Glass, R.J.

1989-01-01

Current interest in storing high-level nuclear waste in underground repositories has resulted in an increased effort to understand the physics of water flow through low-permeability rock. The US Department of Energy is investigating a prospective repository site located in volcanic ash (tuff) hundreds of meters above the water table at Yucca Mountain, Nevada. Consequently, mathematical models and experimental procedures are being developed to provide a better understanding of the hydrology of this low-permeability, partially saturated, fractured rock. Modeling water flow in the vadose zone in soils and in relatively permeable rocks such as sandstone has received considerable attention for many years. The treatment of flow (including nonisothermal conditions) through materials such as the Yucca Mountain tuffs, however, has not received the same level of attention, primarily because it is outside the domain of agricultural and petroleum technology. This paper reviews the status of modeling and experimentation currently being used to understand and predict water flow at the proposed repository site. Several areas of research needs emphasized by the review are outlined. The extremely nonlinear hydraulic properties of these tuffs in combination with their heterogeneous nature makes it a challenging and unique problem from a computational and experimental view point. 101 refs., 14 figs., 1 tab

) Sediment petrographic characterisation and diagenetic pathways of the Miocene Agbada sandstone, Niger delta

International Nuclear Information System (INIS)

Akaegbobi, I. M; Gaupp, R.; Fischer, C.

2003-01-01

Combined petrophysical and petrographic investigations of he Agbada sandstone interbeds has been undertaken in order to determine the controlling factors on the reservoir quality of he paralic sandstone facies. Well logs, petrophysical data and a set of core samples from two wells located in the eastern onshore of he Niger delta spanning a depth interval of 3200 to 330m, formed the basic material for the present study. Four sandstone and siltstone facies units ranging form coastal bar sands through transgressive sands to marine claystones were identified based on petrophysical log signatures. Thin section analysis of a selected set of sandstone samples revealed essentially a unimodal, homogeneous grain size distribution of the detrital mineral components. Quantitative assessment of the mineralogical composition using point count method (300 points) revealed the predominance of dring. etrital quartz (85%) over feldspar minerals (9%) and lithic fragments (6%). A database generated from the point counting of the sandstones provided a broad perspective to the relative variations of the intergranular porosities (28%), cementation and matrix. These are remarkable indicators for low compaction. Authigenic kaoline and illite were identified. The partial leaching of detrital feldspars are responsible for the low percentages of intragranular volume (secondary porosity). The main controlling factor on the high porosity can be traced to either low compactional effects (overpressure?) or total leaching of unknown early cements. We suggest that the excellent reservoir properties of the Agbada sandstones are due to under compaction, caused by continuous long-term over pressuring

Effect of leukotriene receptor antagonists on vascular permeability during endotoxic shock

International Nuclear Information System (INIS)

Cook, J.A.; Li, E.J.; Spicer, K.M.; Wise, W.C.; Halushka, P.V.

1990-01-01

Evidence has accumulated that sulfidopeptide leukotrienes are significant pathogenic mediators of certain hematologic and hemodynamic sequelae of endotoxic shock. In the present study, the effects of a selective LTD4/E4 receptor antagonist, LY171883 (LY), or a selective LTD4 receptor antagonist, SKF-104353 (SKF), were assessed on splanchnic and pulmonary localization of 99mTechnetium-labeled human serum albumin (99mTc-HSA) in acute endotoxic shock in the rat. Dynamic gamma camera imaging of heart (H), midabdominal (GI), and lung regions of interest generated time activity curves for baseline and at 5-35 min after Salmonella enteritidis endotoxin (10 mg/kg, i.v.). Slopes of GI/H and lung/H activity (permeability index, GI/H or lung/H X 10(-3)/min) provided indices of intestinal and lung localization. Rats received LY (30 mg/kg, i.v.), LY vehicle (LY Veh), SKF (10 mg/kg), or SKF vehicle (SK Veh) 10 min prior to endotoxin or endotoxin vehicle. In rats receiving the LY Veh and endotoxin (n = 8) or SKF Veh and endotoxin (n = 12), the splanchnic permeability indices to 99mTc-HSA were increased 11.2-fold and 5.1-fold, respectively (P less than 0.05) compared to vehicle control groups not given endotoxin (n = 5). Pulmonary permeability index for 99mTc-HSA was increased (P less than 0.05) to a lesser extent (3.2-fold) by endotoxin compared to vehicle controls. Pretreatment with SKF reduced the mesenteric permeability index to control levels (P less than 0.05) during the 5-35 min time interval post-endotoxin. LY reduced the mesenteric permeability index by 70%. Pulmonary relative permeability to 99mTc-HSA was not affected by LY pretreatment. Both splanchnic and lung relative permeability to the isotope was transient; at 135-225 min post-endotoxin, splanchnic localization of 99mTc-HSA (n = 4) was not significantly different from vehicle controls in these vascular beds

Heavy mineral sorting in downwards injected Palaeocene sandstone, Siri Canyon, Danish North Sea

DEFF Research Database (Denmark)

Kazerouni, Afsoon Moatari; Friis, Henrik; Svendsen, Johan Byskov

2011-01-01

Post-depositional remobilization and injection of sand are often seen in deep-water clastic systems and has been recently recognised as a significant modifier of deep-water sandstone geometry. Large-scale injectite complexes have been interpreted from borehole data in the Palaeocene Siri Canyon...... of depositional structures in deep-water sandstones, the distinction between "in situ" and injected or remobilised sandstones is often ambiguous. Large scale heavy mineral sorting (in 10 m thick units) is observed in several reservoir units in the Siri Canyon and has been interpreted to represent the depositional...... sorting. In this study we describe an example of effective shear-zone sorting of heavy minerals in a thin downward injected sandstone dyke which was encountered in one of the cores in the Cecilie Field, Siri Canyon. Differences in sorting pattern of heavy minerals are suggested as a tool for petrographic...

A new bee species that excavates sandstone nests.

Science.gov (United States)

Orr, Michael C; Griswold, Terry; Pitts, James P; Parker, Frank D

2016-09-12

Humanity has long been fascinated by animals with apparently unfavorable lifestyles [1]. Nesting habits are especially important because they can limit where organisms live, thereby driving population, community, and even ecosystem dynamics [2]. The question arises, then, why bees nest in active termite mounds [3] or on the rim of degassing volcanoes, seemingly preferring such hardship [4]. Here, we present a new bee species that excavates sandstone nests, Anthophora (Anthophoroides) pueblo Orr (described in Supplemental Information, published with this article online), despite the challenges already inherent to desert life. Ultimately, the benefits of nesting in sandstone appear to outweigh the associated costs in this system. Copyright © 2016 Elsevier Ltd. All rights reserved.

Analysis on the geological features and ore-forming conditions at the southern margin of Erdos basin

International Nuclear Information System (INIS)

Ren Zhongxian; Shen Pingxi; Chen Fenling

2014-01-01

At the southern margin of Erdos basin, the paleo-interlayer-oxidation was developed in the medium-coarse-grained sandstone of Middle Jurassic System. High content uranium was enriched which are favorable for sandstone-type uranium deposit. There had been found multiple sandstone-type uranium deposits (ore occurrences) in this area. Uranium mineralization occurs in the sand body of braided fluvial facies in the lower member of Zhiluo Formation of Middle Jurassic System. It was controlled by the paleo-interlayer-oxidation. Uranium mineralization was closely related with the permeability of sandstone and occurs generally in the sandstones where is loose cementation and water permeability better. The stratum of Middle Jurassic System was extensively developed in the work area. Therefore it has great prospecting potential for the sandstone-type uranium deposit. (authors)

Deep permeability of the San Andreas Fault from San Andreas Fault Observatory at Depth (SAFOD) core samples

Science.gov (United States)

Morrow, Carolyn A.; Lockner, David A.; Moore, Diane E.; Hickman, Stephen H.

2014-01-01

The San Andreas Fault Observatory at Depth (SAFOD) scientific borehole near Parkfield, California crosses two actively creeping shear zones at a depth of 2.7 km. Core samples retrieved from these active strands consist of a foliated, Mg-clay-rich gouge containing porphyroclasts of serpentinite and sedimentary rock. The adjacent damage zone and country rocks are comprised of variably deformed, fine-grained sandstones, siltstones, and mudstones. We conducted laboratory tests to measure the permeability of representative samples from each structural unit at effective confining pressures, Pe up to the maximum estimated in situ Pe of 120 MPa. Permeability values of intact samples adjacent to the creeping strands ranged from 10−18 to 10−21 m2 at Pe = 10 MPa and decreased with applied confining pressure to 10−20–10−22 m2 at 120 MPa. Values for intact foliated gouge samples (10−21–6 × 10−23 m2 over the same pressure range) were distinctly lower than those for the surrounding rocks due to their fine-grained, clay-rich character. Permeability of both intact and crushed-and-sieved foliated gouge measured during shearing at Pe ≥ 70 MPa ranged from 2 to 4 × 10−22 m2 in the direction perpendicular to shearing and was largely insensitive to shear displacement out to a maximum displacement of 10 mm. The weak, actively-deforming foliated gouge zones have ultra-low permeability, making the active strands of the San Andreas Fault effective barriers to cross-fault fluid flow. The low matrix permeability of the San Andreas Fault creeping zones and adjacent rock combined with observations of abundant fractures in the core over a range of scales suggests that fluid flow outside of the actively-deforming gouge zones is probably fracture dominated.

Effect of permeability enhancers on paracellular permeability of acyclovir.

Science.gov (United States)

Ates, Muge; Kaynak, Mustafa Sinan; Sahin, Selma

2016-06-01

According to Biopharmaceutics Classification System (BCS), acyclovir is a class III (high solubility, low permeability) compound, and it is transported through paracellular route by passive diffusion. The aim of this study was to investigate the effect of various pharmaceutical excipients on the intestinal permeability of acyclovir. The single-pass in-situ intestinal perfusion (SPIP) method was used to estimate the permeability values of acyclovir and metoprolol across different intestinal segments (jejunum, ileum and colon). Permeability coefficient (Peff ) of acyclovir was determined in the absence and presence of a permeation enhancer such as dimethyl β-cyclodextrin (DM-β-CD), sodium lauryl sulfate (SLS), sodium caprate (Cap-Na) and chitosan chloride. All enhancers increased the permeability of paracellularly transported acyclovir. Although Cap-Na has the highest permeability-enhancing effect in all segments, permeation-enhancing effect of chitosan and SLS was only significant in ileum. On the other hand, DM-β-CD slightly decreased the permeability in all intestinal segments. These findings have potential implication concerning the enhancement of absorption of paracellularly transported compounds with limited oral bioavailability. In the case of acyclovir, Cap-Na either alone or in combination with SLS or chitosan has the potential to improve its absorption and bioavailability and has yet to be explored. © 2016 Royal Pharmaceutical Society.

Report on Hydrologic Flow in Low-Permeability Media

Energy Technology Data Exchange (ETDEWEB)

Liu, Hui-Hai; Birkholzer, Jens

2013-11-13

We demonstrate that under normal conditions (under which there are no intersections between tunnels/drifts and conductive geological structures, such as faults), the water flow velocity in the damage zone, as a result of non-Darcian flow behavior, is extremely small such that solute transport is dominated by diffusion, rather than advection. We show that unless non-Darcian flow behavior is considered, significant errors can occur in the “measured” relative-permeability values. We propose a hypothesis to consider the temperature impact based on limited test results from the petroleum literature. To consider the bedding effects, we present an empirical relationship between water flux and hydraulic gradient for non-Darcian water flow in anisotropic cases.

Geologic History of Eocene Stonerose Fossil Beds, Republic, Washington, USA

Directory of Open Access Journals (Sweden)

George E. Mustoe

2015-07-01

Full Text Available Eocene lakebed sediments at Stonerose Interpretive Center in Republic, Washington, USA are one of the most important Cenozoic fossil sites in North America, having gained international attention because of the abundance and diversity of plant, insect, and fish fossils. This report describes the first detailed geologic investigation of this unusual lagerstätten. Strata are gradationally divided into three units: Siliceous shale that originated as diatomite, overlain by laminated mudstone, which is in turn overlain by massive beds of lithic sandstone. The sedimentary sequence records topographic and hydrologic changes that caused a deep lake to become progressively filled with volcaniclastic detritus from earlier volcanic episodes. The location of the ancient lake within an active graben suggests that displacements along the boundary faults were the most likely trigger for changes in depositional processes.

Age, sedimentary environments, and other aspects of sandstone and related host rocks for uranium deposits

International Nuclear Information System (INIS)

1983-01-01

Project II of the Uranium Geology Working Group was assigned to the study of sedimentary basins and sandstone - type uranium deposits. About 40% of the worlds's uranium resources are contained in sandstone-type deposits, which has led to extensive research. The research was carried out mainly by correspondence, and the results reported by 21 geologists from 10 nations are summarized in this report. It investigated five topics dealing with important aspects of the geology of uranium ores in sandstone host formations: age of host rock; partitioning of uranium between continental and marine sediments; latitude limitation on formation of sandstone deposits; effect of rock formation dip on sandstone ores; usefulness of stable isotope and fluid inclusion studies. The results of studies on these subjects form part of a wider programme of the Working Group, whose final results will be presented at the 27th International Geological Congress in Moscow in 1984

Sandstone Relief Geohazards and their Mitigation: Rock Fall Risk Management in the Bohemian Switzerland National Park

Czech Academy of Sciences Publication Activity Database

Vařilová, Zuzana; Zvelebil, J.

2005-01-01

Roč. 44, - (2005), s. 53-58 ISSN 1682-5519. [Sandstone Landscapes in Europe. Past, Present and Future. International Conference on Sandstone Landscapes /2./. Vianden, 25.05.2005-28.05.2005] Keywords : sandstones * rock-slope instability * rock fall * risk evalution and mitigation * monitoring net * remedial works Subject RIV: DO - Wilderness Conservation

Study of petrological characteristics of uranium-bearing sandstone in the south of ordos basin, China

International Nuclear Information System (INIS)

Tian Cheng; Jia Licheng; Li Song; Zhang Zimin

2007-01-01

This paper discusses the relation between uranium-bearing abundance and texture constituent of sedimentary rock, on the basis of the research of petrological characteristic of sandstone in the south of Ordos basin. The influence of infiltration of sandstone and uranium migration and accumulation by the major diagenesis of compaction and cementation, clay minerals evolution, corrosion and forming of secondary porosity are discussed. Uranium-bearing sandstones are divided into four types and their petrological characteristics are discussed. After mineralization conditions being summed up, the uranium-mineralization model of sandstone-type is built. Reliable petrological evidences for evaluating favourable uranium mineralization rich areas are furnished. (authors)

Analysis of Critical Permeabilty, Capillary Pressure and Electrical Properties for Mesaverde Tight Gas Sandstones from Western U.S. Basins

Energy Technology Data Exchange (ETDEWEB)

Alan Byrnes; Robert Cluff; John Webb; John Victorine; Ken Stalder; Daniel Osburn; Andrew Knoderer; Owen Metheny; Troy Hommertzheim; Joshua Byrnes; Daniel Krygowski; Stefani Whittaker

2008-06-30

Although prediction of future natural gas supply is complicated by uncertainty in such variables as demand, liquefied natural gas supply price and availability, coalbed methane and gas shale development rate, and pipeline availability, all U.S. Energy Information Administration gas supply estimates to date have predicted that Unconventional gas sources will be the dominant source of U.S. natural gas supply for at least the next two decades (Fig. 1.1; the period of estimation). Among the Unconventional gas supply sources, Tight Gas Sandstones (TGS) will represent 50-70% of the Unconventional gas supply in this time period (Fig. 1.2). Rocky Mountain TGS are estimated to be approximately 70% of the total TGS resource base (USEIA, 2005) and the Mesaverde Group (Mesaverde) sandstones represent the principal gas productive sandstone unit in the largest Western U.S. TGS basins including the basins that are the focus of this study (Washakie, Uinta, Piceance, northern Greater Green River, Wind River, Powder River). Industry assessment of the regional gas resource, projection of future gas supply, and exploration programs require an understanding of reservoir properties and accurate tools for formation evaluation. The goal of this study is to provide petrophysical formation evaluation tools related to relative permeability, capillary pressure, electrical properties and algorithms for wireline log analysis. Detailed and accurate moveable gas-in-place resource assessment is most critical in marginal gas plays and there is need for quantitative tools for definition of limits on gas producibility due to technology and rock physics and for defining water saturation. The results of this study address fundamental questions concerning: (1) gas storage; (2) gas flow; (3) capillary pressure; (4) electrical properties; (5) facies and upscaling issues; (6) wireline log interpretation algorithms; and (7) providing a web-accessible database of advanced rock properties. The following text

Rate type isotach compaction of consolidated sandstone

NARCIS (Netherlands)

Waal, J.A. de; Thienen-Visser, K. van; Pruiksma, J.P.

2015-01-01

Laboratory experiments on samples from a consolidated sandstone reservoir are presented that demonstrate rate type compaction behaviour similar to that observed on unconsolidated sands and soils. Such rate type behaviour can have large consequences for reservoir compaction, surface subsidence and

Fast evolving conduits in clay-bonded sandstone: Characterization, erosion processes and significance for the origin of sandstone landforms

Czech Academy of Sciences Publication Activity Database

Bruthans, J.; Svetlik, D.; Soukup, J.; Schweigstillová, Jana; Válek, Jan; Sedláčková, M.; Mayo, A.L.

2012-01-01

Roč. 177, December (2012), s. 178-193 ISSN 0169-555X R&D Projects: GA AV ČR IAA300130806 Institutional support: RVO:67985891 ; RVO:68378297 Keywords : sandstone * erosion * piping * tensile strength * conduit * landform Subject RIV: DA - Hydrology ; Limnology Impact factor: 2.552, year: 2012

A special kind of sandstone-type uranium deposit related to Jurassic palaeochannel systems in the northeastern Ordos Basin, China

International Nuclear Information System (INIS)

Li Ziying; Fang Xiheng; Xia Yuliang; Sun Ye; Jiao Yangquan; Chen Anping; Zhang Ke

2010-01-01

Dongsheng sandstone-type uranium deposit is a large one discovered in recent years in the northeastern Ordos Basin, China. It is a special kind of sandstone-type uranium deposit,different from other ordinary sandstone-type deposits because of its unique signatures. It is generally controlled by a transitional zone between greenish and grayish sandstones, both of those two kinds of sandstones now indicate reduced geochemical environments. The greenish color of the palaeo-oxidized sandstones mainly results from chloritization and epidotization related to oil and gas secondary reduction processes. The deposit genetically is different from ordinary sandstone uranium deposits,which is of more complex origin,undergoing not only palaeo-oxidization mineralization process, but also oil-gas fluid and hydrothermal reworking processes. It is spatially related to Jurassic Zhiluo Formation with braided palaeo channel systems. The uranium mineralization zone with higher grade usually exists in the branching area of the distributary channels of main braided streams, whose sandstone heterogeneity shows a transfer sedimentary facies from the braided stream sedimentary system to the braided delta sedimentary system. Statistical results show that medium and fine-grained sandstones are the most favorable rock types for uranium mineralization. (authors)

Analysis on metallogenic conditions of paleochannel sandstone type uranium deposits in kelulun region

Energy Technology Data Exchange (ETDEWEB)

Mingyue, Feng [Beijing Research Inst. of Uranium Geology, Beijing (China)

1999-07-01

On the basis of comprehensively analyzing metallogenic conditions of paleochannel sandstone type uranium deposits, the author discusses regional geologic background, characteristics of the basement and sedimentary cover of Kelulun basin and Huchawula-Hulun Lake basin, and the metallogenic potential of paleochannel sandstone type uranium deposits is proposed.

Analysis on metallogenic conditions of paleochannel sandstone type uranium deposits in kelulun region

International Nuclear Information System (INIS)

Feng Mingyue

1999-01-01

On the basis of comprehensively analyzing metallogenic conditions of paleochannel sandstone type uranium deposits, the author discusses regional geologic background, characteristics of the basement and sedimentary cover of Kelulun basin and Huchawula-Hulun Lake basin, and the metallogenic potential of paleochannel sandstone type uranium deposits is proposed

Influence of Structural Features and Fracture Processes on Surface Roughness: A Case Study from the Krosno Sandstones of the Górka–Mucharz Quarry (Little Beskids, Southern Poland

Directory of Open Access Journals (Sweden)

Pieczara Łukasz

2015-09-01

Full Text Available The paper presents the results of analysis of surface roughness parameters in the Krosno Sandstones of Mucharz, southern Poland. It was aimed at determining whether these parameters are influenced by structural features (mainly the laminar distribution of mineral components and directional distribution of non-isometric grains and fracture processes. The tests applied in the analysis enabled us to determine and describe the primary statistical parameters used in the quantitative description of surface roughness, as well as specify the usefulness of contact profilometry as a method of visualizing spatial differentiation of fracture processes in rocks. These aims were achieved by selecting a model material (Krosno Sandstones from the Górka-Mucharz Quarry and an appropriate research methodology. The schedule of laboratory analyses included: identification analyses connected with non-destructive ultrasonic tests, aimed at the preliminary determination of rock anisotropy, strength point load tests (cleaved surfaces were obtained due to destruction of rock samples, microscopic analysis (observation of thin sections in order to determine the mechanism of inducing fracture processes and a test method of measuring surface roughness (two- and three-dimensional diagrams, topographic and contour maps, and statistical parameters of surface roughness. The highest values of roughness indicators were achieved for surfaces formed under the influence of intragranular fracture processes (cracks propagating directly through grains. This is related to the structural features of the Krosno Sandstones (distribution of lamination and bedding.

Radionuclide transport in sandstones with WIPP brine

International Nuclear Information System (INIS)

Weed, H.C.; Bazan, F.; Fontanilla, J.; Garrison, J.; Rego, J.; Winslow, A.M.

1981-02-01

Retardation factors (R) have been measured for the transport of 3 H, /sup 95m/Tc, and 85 Sr in WIPP brine using St. Peter, Berea, Kayenta, and San Felipe sandstone cores. If tritium is assumed to have R=1, /sup 95m/Tc has R=1.0 to 1.3 and therefore is essentially not retarded. Strontium-85 has R = 1.0 to 1.3 on St. Peter, Berea, and Kayenta, but R=3 on San Felipe. This is attributed to sorption on the matrix material of San Felipe, which has 45 volume % matrix compared with 1 to 10 volume % for the others. Retardation factors (R/sub s/) for 85 Sr calculated from static sorption measurements are unity for all the sandstones. Therefore, the static and transport results for 85 Sr disagree in the case of San Felipe, but agree for St. Peter, Berea, and Kayenta

Reservoir compartmentalization and management strategies: Lessons learned in the Illinois basin

Energy Technology Data Exchange (ETDEWEB)

Grube, J.P.; Crockett, J.E.; Huff, B.G. [and others

1997-08-01

A research project jointly sponsored by the US Department of Energy and the Illinois State Geological Survey focused on the Cypress and Aux Vases Formations (Mississippian), major clastic reservoirs in the Illinois Basin. Results from the research showed that understanding the nature and distribution of reservoir compartments, and using effective reservoir management strategies, can significantly improve recovery efficiencies from oil fields in this mature basin. Compartments can be most effectively drained where they are geologically well defined and reservoir management practices are coordinated through unified, compartment-wide, development programs. Our studies showed that the Cypress and Aux Vases reservoirs contain lateral and vertical permeability barriers forming compartments that range in size from isolated, interlaminated sandstone and shale beds to sandstone bodies tens of feet in thickness and more than a mile in length. Stacked or shingled, genetically similar sandstone bodies are commonly separated by thin impermeable intervals that can be difficult to distinguish on logs and can, therefore, cause correlation problems, even between wells drilled on spacing of less than ten acres. Lateral separation of sandstone bodies causes similar problems. Reservoir compartmentalization reduces primary and particularly secondary recovery by trapping pockets of by-passed or banked oil. Compartments can be detected by comparing recovery factors of genetically similar sandstone bodies within a field; using packers to separate commingled intervals and analyzing fluid recoveries and pressures; making detailed core-to-log calibrations that identify compartment boundaries; and analyzing pressure data from waterflood programs.

Characterization of the Qishn sandstone reservoir, Masila Basin-Yemen, using an integrated petrophysical and seismic structural approach

Science.gov (United States)

Lashin, Aref; Marta, Ebrahim Bin; Khamis, Mohamed

2016-03-01

This study presents an integrated petrophysical and seismic structural analysis that is carried out to evaluate the reservoir properties of Qishn sandstone as well as the entrapment style of the hydrocarbons at Sharyoof field, Sayun-Masila Basin that is located at the east central of Yemen. The reservoir rocks are dominated by clean porous and permeable sandstones zones usually intercalated with some clay stone interbeds. As identified from well logs, Qishn sandstone is classified into subunits (S1A, S1B, S1C and S2) with different reservoir characteristics and hydrocarbon potentiality. A number of qualitative and quantitative well logging analyses are used to characterize the different subunits of the Qishn reservoir and identify its hydrocarbon potentiality. Dia-porosity, M-N, Pickett, Buckles plots, petrophysical analogs and lateral distribution maps are used in the analysis. Shale volume, lithology, porosity, and fluid saturation are among the most important deduced parameters. The analysis revealed that S1A and S1C are the main hydrocarbon-bearing units. More specifically, S1A unit is the best, as it attains the most prolific hydrocarbon saturations (oil saturation "SH″ up to 65) and reservoir characteristics. An average petrophysical ranges of 4-21%, 16-23%, 11-19%, 0-65%, are detected for S1A unit, regarding shale volume, total and effective porosity, and hydrocarbon saturation, respectively. Meanwhile, S1B unit exhibits less reservoir characteristics (Vsh>30%, ϕEff<15% and SH< 15%). The lateral distribution maps revealed that most of the hydrocarbons (for S1A and S1C units) are indicated at the middle of the study area as NE-SW oriented closures. The analysis and interpretation of seismic data had clarified that the structure of study area is represented by a big middle horst bounded by a group of step-like normal faults at the extreme boundaries (faulted anticlinal-structure). In conclusion, the entrapment of the encountered hydrocarbon at Sharyoof oil

Suitability of Torrent Permeability Tester to measure air-permeability of covercrete

Energy Technology Data Exchange (ETDEWEB)

Andrade, C.; Gonzales-Gasca, C. [Institute of Construction Sciences ' Eduardo Torroja' , Madrid (Spain); Torrent, R. [Portland Cement Institute, (Argentina)

2000-07-01

Suitability of the Torrent Permeability Tester (TPT) to measure the permeability of covercrete to air, both in the laboratory and the field, is investigated, and test results obtained in laboratory studies are discussed. The tests performed included the determination of air permeability (TPT method), oxygen permeability (Cembureau method) and capillary suction, rapid chloride permeability test (ASTM C 1202), as well as a one-year carbonation depth test. Concrete specimens of various compositions and curing regimes were used in the tests; the gas-permeability tests were repeated on the same specimens after 28 days, than again at 6 months and 12 months. Test results confirmed the suitability of the TPT as a useful tool in the characterization of the quality the of concrete cover. It was found to be sensitive to changes in concrete quality; repeatable for sensitive properties such as gas permeability ; also, it was found to correlate well with other durability-related properties. 10 refs., 8 tabs., 8 figs.

Dubois Quadrangle, Idaho and Montana

International Nuclear Information System (INIS)

Wodzicki, A.; Krason, J.

1981-06-01

Within the Dubois Quadrangle (Idaho and Montana), environments favorable for uranium deposits, based on National Uranium Resource Evaluation criteria, occur in the McGowan Creek Formation and within some Tertiary sedimentary basins. The Mississippian McGowan Creek Formation consists of uraniferous, black, siliceous mudstone and chert with minor porous sedimentary channels. In the southern Beaverhead Mountains it has been fractured by a bedding-plane fault, and uranium has been further concentrated by circulating groundwater in the porous channels and brecciated zones, both of which contain about 200 ppM uranium. The northern parts of the Pahsimeroi River, Lemhi River, Medicine Lodge Creek, Horse Prairie, and Sage Creek Basins are considered favorable for sandstone-type uranium deposits. Evidence present includes suitable source rocks such as rhyolitic flow breccia, laharic deposits, or strongly welded tuffs; permeable sediments, including most sandstones and conglomerates, providing they do not contain devitrified glass; suitable reductants such as lignite, pyrite, or low-Eh geothermal water; and uranium occurrences

Interpretation of massive sandstones in ephemeral fluvial settings: A case study from the Upper Candelária Sequence (Upper Triassic, Paraná Basin, Brazil)

Science.gov (United States)

Horn, Bruno Ludovico Dihl; Goldberg, Karin; Schultz, Cesar Leandro

2018-01-01

Ephemeral rivers display a wide range of upper- and lower-flow regime structures due to great flow-velocity changes during the floods. The development of flow structures in these setting is yet to be understood, especially in the formation of thick, massive sandstones. The Upper Triassic of Southern Gondwana was marked by a climate with great seasonal changes, yet there is no description of river systems with seasonal characteristics in Southern Gondwana. This work aims to characterize a ephemeral alluvial system of the Upper Triassic of the Paraná Basin. The characteristics of the deposits are discussed in terms of depositional processes through comparison with similar deposits from literature, flow characteristics and depositional signatures compared to flume experiments. The alluvial system is divided in four facies associations: (1) channels with wanning fill, characterized by low width/thickness ratio, tabular bodies, scour-and-fill structures with upper- and lower-flow regime bedforms; (2) channels with massive fill, characterized by low w/t ratio, sheet-like bodies, scour-and-fill structures with massive sandstones; (3) proximal sheetfloods, characterized by moderate w/t ratio, sheet-like bodies with upper- and lower-flow regime bedforms and (4) distal sheetfloods, characterized by high w/t ratio, sheet-like bodies with lower-flow regime bedforms. Evidence for the seasonal reactivation of the riverine system includes the scarcity of well-developed macroforms and presence of in-channel mudstones, thick intraformational conglomerates, and the occurrence of well- and poorly-preserved vertebrate bones in the same beds. The predominantly massive sandstones indicate deposition from a hyperconcentrated flow during abrupt changes in flow speed, caused by de-confinement or channel avulsion, whereas turbulent portions of the flow formed the upper- and lower-flow regime bedforms after the deposition of the massive layers. The upper portion of the Candelária Sequence

Investigation of the structure of debris beds formed from fuel rods fragmentation

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Duc-Hanh; Fichot, Florian; Topin, Vincent, E-mail: vincent.topin@irsn.fr

2017-03-15

This paper is a study of debris beds that can form in the core of a nuclear power plant under severe accident conditions. Such beds are formed of fragments of pellets and cladding remnants, as observed in the TMI-2 core. Many important issues are related with the morphology of those debris beds: are they coolable in case of water injection and how does molten corium progress through them if they are not coolable? The answers to those questions depend on the structure of the debris bed: porosity, number and arrangement of particles. In order to obtain relevant information, a numerical simulation of the formation of the debris bed is proposed. It relies on a granular approach of the type called “Contact Dynamics” to simulate the collapse of debris and their accumulation. Two different schemes of fuel pellet fragmentation are considered and simulations for different degrees of fragmentation of the pellets are performed. The results show that the number of axial cracks on fuel pellets strongly influences the final porosity of the debris bed. Porosities vary between 31% (less coolable cases) and 45% (similar to TMI-2 observations), with a most probable configuration around 41%. The specific surface of the bed is also evaluated. In the last part, a simple model is used to estimate the impact of the variation in geometry of the numeric debris beds on their flow properties. We show that the permeability and passability can vary respectively with a range of 30% and 15% depending on the number of fragment per pellet. The other benefits of the approach are finally discussed. Among them, the possibility to print 3D samples from the calculated images of debris beds appears as a promising perspective to perform experiments with realistic debris beds.

Permeability Prediction in Deep Coal Seam: A Case Study on the No. 3 Coal Seam of the Southern Qinshui Basin in China

Science.gov (United States)

2013-01-01

The coal permeability is an important parameter in mine methane control and coal bed methane (CBM) exploitation, which determines the practicability of methane extraction. Permeability prediction in deep coal seam plays a significant role in evaluating the practicability of CBM exploitation. The coal permeability depends on the coal fractures controlled by strata stress, gas pressure, and strata temperature which change with depth. The effect of the strata stress, gas pressure, and strata temperature on the coal (the coal matrix and fracture) under triaxial stress and strain conditions was studied. Then we got the change of coal porosity with strata stress, gas pressure, and strata temperature and established a coal permeability model under tri-axial stress and strain conditions. The permeability of the No. 3 coal seam of the Southern Qinshui Basin in China was predicted, which is consistent with that tested in the field. The effect of the sorption swelling on porosity (permeability) firstly increases rapidly and then slowly with the increase of depth. However, the effect of thermal expansion and effective stress compression on porosity (permeability) increases linearly with the increase of depth. The most effective way to improve the permeability in exploiting CBM or extracting methane is to reduce the effective stress. PMID:24396293

Experimental deformation in sandstone, carbonates and quartz aggregate

Energy Technology Data Exchange (ETDEWEB)

Cheung, Cecilia See Nga [Stony Brook Univ., NY (United States)

2015-05-01

The first part of my thesis is mainly focused on the effect of grain size distribution on compaction localization in porous sandstone. To identify the microstructural parameters that influence compaction band formation, I conducted a systematic study of mechanical deformation, failure mode and microstructural evolution in Bleurswiller and Boise sandstones, of similar porosity (~25%) and mineralogy but different sorting. Discrete compaction bands were observed to develop over a wide range of pressure in the Bleurswiller sandstone that has a relatively uniform grain size distribution. In contrast, compaction localization was not observed in the poorly sorted Boise sandstone. My results demonstrate that grain size distribution exerts important influence on compaction band development, in agreement with recently published data from Valley of Fire and Buckskin Gulch, as well as numerical studies. The second part aimed to improve current knowledge on inelastic behavior, failure mode and brittle-ductile transition in another sedimentary rock, porous carbonates. A micritic Tavel (porosity of ~13%) and an allochemical Indiana (~18%) limestones were deformed under compaction in wet and dry conditions. At lower confining pressures, shear localization occurred in brittle faulting regime. Through transitional regime, the deformation switched to cataclastic flow regime at higher confining pressure. Specifically in the cataclastic regime, the (dry and wet) Tavel and dry Indiana failed by distributed cataclastic flow, while in contrast, wet Indiana failed as compaction localization. My results demonstrate that different failure modes and mechanical behaviors under different deformation regimes and water saturation are fundamental prior to any geophysical application in porous carbonates. The third part aimed to focus on investigating compaction on quartz aggregate starting at low (MPa) using X-ray diffraction. We report the diffraction peak evolution of quartz with increasing

Effect of a low-permeability layer on calculated gas flow at Yucca Mountain

International Nuclear Information System (INIS)

Lu, Ning; Amter, S.; Ross, B.

1990-01-01

Yucca Mountain is being studied to determine its suitability as a location for a high-level nuclear waste repository. Amter and Ross developed a model called TGIF (Topographic Induced Flow) to simulate gas flow under Yucca Mountain. The TGIF model differs significantly from previous gas flow models. It uses a governing equation that is based on the concept of freshwater head, thus avoiding the numerical problems associated with the near-cancellation of the forces due to gravity and the pressure gradient. Unlike most other models, dipping, layered media can be simulated. This paper describes a systematic sensitivity study that was designed to test several aspects of the TGIF model when used to simulate gas flow under Yucca Mountain. Values of three important inputs to the model were systematically varied to form a matrix of 80 runs. The matrix consisted of five values of permeability contrast between a bedded tuff layer and surrounding welded units (in all cases, bulk permeabilities were used to represent the combined effect of both fractures and matrix permeability), four temperature profiles representing different stages of repository cooldown, and four finite-difference grids

Effect of a low-permeability layer on calculated gas flow at Yucca Mountain

Energy Technology Data Exchange (ETDEWEB)

Lu, Ning; Amter, S.; Ross, B. [Disposal Safety, Inc., Washington, DC (USA)

1990-12-31

Yucca Mountain is being studied to determine its suitability as a location for a high-level nuclear waste repository. Amter and Ross developed a model called TGIF (Topographic Induced Flow) to simulate gas flow under Yucca Mountain. The TGIF model differs significantly from previous gas flow models. It uses a governing equation that is based on the concept of freshwater head, thus avoiding the numerical problems associated with the near-cancellation of the forces due to gravity and the pressure gradient. Unlike most other models, dipping, layered media can be simulated. This paper describes a systematic sensitivity study that was designed to test several aspects of the TGIF model when used to simulate gas flow under Yucca Mountain. Values of three important inputs to the model were systematically varied to form a matrix of 80 runs. The matrix consisted of five values of permeability contrast between a bedded tuff layer and surrounding welded units (in all cases, bulk permeabilities were used to represent the combined effect of both fractures and matrix permeability), four temperature profiles representing different stages of repository cooldown, and four finite-difference grids.

Application status and vistas of sequence stratigraphy to the exploration of sandstone-hosted uranium deposits

International Nuclear Information System (INIS)

Guo Qingyin; Chen Zuyi; Yu Jinshui; Han Shuqin

2008-01-01

Sequence stratigraphy is a newly developed subject based on seismostratigraphy, and has been widely applied in the exploration of hydrocarbon and other sedimentogenic mineral deposits and great achievements have been obtained. However, the application of sequence stratigraphy to the exploration of sandstone-hosted uranium deposits is just at the beginning. In this paper, some primary research achievements of sequence stratigraphy to the exploration of sandstone-hosted uranium deposits are summarized, and problems and their reasons of the application of sequence stratigraphy are discussed. Further more, according to characteristics of sandstone-hosted uranium deposits and the development of sequence stratigraphy, the application vistas of sequence stratigraphy to the exploration of sandstone-hosted uranium deposits are estimated. Finally, application directions are proposed, and some specific suggestions are given. (authors)

Water infiltration and heat transfer in one dimensional unsaturated packed beds; Fuhowa ryushi sonai no ichijigen suibun nagare to dennetsu tokusei

Energy Technology Data Exchange (ETDEWEB)

Aoki, K; Akahori, M; Hattori, M [Nagaoka University of Technology, Niigata (Japan); Shiraishi, N [Toshiba Corp., Tokyo (Japan)

1998-05-25

Water and heat transport in unsaturated packed beds due to supplying hot water have been investigated experimentally and theoretically. Using various sizes of glass beads, capillary pressure and permeability in packed beds were measured in unsaturated beds. The distributions in water saturation and temperature were predicted for one dimensional packed bed, based on a model assuming local thermal equilibrium among water, gas and particles at any specific space. The predicted temperature distributions were compared with the experimental results obtained using various glass sizes. In layered packed beds, water saturation becomes discontinuous at the interface of two layers because of the difference of the water characteristics between two beds. Water penetrates faster in coarse-over fine-textured profile compared with in fine-over coarse-textured profile. Similarly, the temperature rises faster in former profile under the same supplied heat quantity. 11 refs., 13 figs., 1 tab.

Numerical analysis of a heat-generating, truncated conical porous bed in a fluid-filled enclosure

International Nuclear Information System (INIS)

Chakravarty, Aranyak; Datta, Priyankan; Ghosh, Koushik; Sen, Swarnendu; Mukhopadhyay, Achintya

2016-01-01

Analysis of natural convection in enclosures containing heat generating porous medium has important applications related to geothermal, chemical, thermal and nuclear energy such as in-vessel cooling of debris beds in nuclear reactors, cooling of coal stockpiles etc. The objective of the present numerical study is to characterise the pattern of fluid flow and energy transfer during steady laminar natural convective flow in a cylindrical enclosure with a centrally placed heat generating porous bed. Flow through porous region is modelled using Darcy–Brinkmann–Forchheimer model and local thermal equilibrium is assumed for the porous region. Analysis is carried out for a wide range of Rayleigh number (Ra), Darcy number (Da) and thermal conductivity ratio, as well as for different bed geometries. It is observed that in addition to Ra and Da, the bed geometry also plays a very important role in determining flow field and temperature distribution within the enclosure. Interestingly, a significant change is observed in energy transfer mode from the porous bed corresponding to specific values of bed permeability and bed heat generation rate. This is characterised in terms of Ra and Da. Further, it is observed that this change in energy transfer mode is highly dependent on Ra. - Highlights: • Natural convection is analysed in an enclosure with a heat generating porous bed. • Effect of dimensionless parameters as well as bed geometry has been investigated. • Energy transfer mechanism from porous bed changes with dimensionless parameters. • Bed geometry significantly affects fluid flow and energy transfer in the enclosure.

Quantitative mineralogical analysis of sandstones using x-ray diffraction techniques

International Nuclear Information System (INIS)

Ward, C.R.; Taylor, J.C.

1999-01-01

Full text: X-ray diffraction has long been used as a definitive technique for mineral identification based on the measuring the internal atomic or crystal structures present in powdered rocks; soils and other mineral mixtures. Recent developments in data gathering and processing, however, have provided an improved basis for its use as a quantitative tool, determining not only the nature of the minerals but also the relative proportions of the different minerals present. The mineralogy of a series of sandstone samples from the Sydney and Bowen Basins of eastern Australia has been evaluated by X-ray diffraction (XRD) on a quantitative basis using the Australian-developed SIROQUANT data processing technique. Based on Rietveld principles, this technique generates a synthetic X-ray diffractogram by adjusting and combining full-profile patterns of minerals nominated as being present in the sample and interactively matches the synthetic diffractogram under operator instructions to the observed diffractogram of the sample being analysed. The individual mineral patterns may be refined in the process, to allow for variations in crystal structure of individual components or for factors such as preferred orientation in the sample mount. The resulting output provides mass percentages of the different minerals in the mixture, and an estimate of the error associated with each individual percentage determination. The chemical composition of the mineral mixtures indicated by SIROQUANT for each individual sandstone studied was estimated using a spreadsheet routine, and the indicated proportion of each oxide in each sample compared to the actual chemical analysis of the same sandstone as determined independently by X-ray fluorescence spectrometry. The results show a high level of agreement for all major chemical constituents, indicating consistency between the SIROQUANT XRD data and the whole-rock chemical composition. Supplementary testing with a synthetic corundum spike further

Elementary theory of bed-sediment entrainment by debris flows and avalanches

Science.gov (United States)

Iverson, Richard M.

2012-01-01

Analyses of mass and momentum exchange between a debris flow or avalanche and an underlying sediment layer aid interpretations and predictions of bed-sediment entrainment rates. A preliminary analysis assesses the behavior of a Coulomb slide block that entrains bed material as it descends a uniform slope. The analysis demonstrates that the block's momentum can grow unstably, even in the presence of limited entrainment efficiency. A more-detailed, depth-integrated continuum analysis of interacting, deformable bodies identifies mechanical controls on entrainment efficiency, and shows that entrainment rates satisfy a jump condition that involves shear-traction and velocity discontinuities at the flow-bed boundary. Explicit predictions of the entrainment rateEresult from making reasonable assumptions about flow velocity profiles and boundary shear tractions. For Coulomb-friction tractions, predicted entrainment rates are sensitive to pore fluid pressures that develop in bed sediment as it is overridden. In the simplest scenario the bed sediment liquefies completely, and the entrainment-rate equation reduces toE = 2μ1gh1 cos θ(1 − λ1)/ , where θ is the slope angle, μ1 is the flow's Coulomb friction coefficient, h1 is its thickness, λ1 is its degree of liquefaction, and is its depth-averaged velocity. For values ofλ1ranging from 0.5 to 0.8, this equation predicts entrainment rates consistent with rates of 0.05 to 0.1 m/s measured in large-scale debris-flow experiments in which wet sediment beds liquefied almost completely. The propensity for bed liquefaction depends on several factors, including sediment porosity, permeability, and thickness, and rates of compression and shear deformation that occur when beds are overridden.

Current status and prospects of uranium geology developments of foreign in-situ leachable sandstone type uranium deposits

International Nuclear Information System (INIS)

Wang Zhengbang

2002-01-01

Firstly, with emphasis on in-situ leachable sandstone-type uranium deposits, the prospecting history of uranium deposits worldwide and its scientific research development are generally reviewed in four steps, and their basic historical experience is also summarized. Secondly, based on the detailed description of current development status of uranium geology of foreign in-situ leachable sandstone-type uranium deposits the important strategic position of sandstone-type uranium deposits in overall uranium resources all-over-the-world and its classification, spatial-temporal distribution and regulation, and metallogenic condition of sandstone-type uranium deposits are analysed thoroughly in five aspects: techtonics, paleo-climate, hydrogeology, sedimentary facies and lithology, as well as uranium sources: Afterwards, evaluation principles of three type of hyper-genic, epigenetic infiltrated sandstone-type uranium deposits are summarized. Based on sandstone-type uranium deposits located two important countries: the United States and Russia, the current development status of prospecting technology for in-situ leachable sandstone-type uranium deposits in foreign countries is outlined. Finally, according to the prospects of supply-demand development of global uranium resources, the author points out seriously that Chinese uranium geology is faced with a severe challenge, and proposes directly four strategic measures that should be taken

Nodular features from Proterozoic Sonia Sandstone, Jodhpur Group ...

Indian Academy of Sciences (India)

Corresponding author. e-mail: parthageology@gmail.com. The Sonia ..... cement variety in the form of dispersed dark brown clots and .... content within the nodule sandstones bear sig- nature in ..... Carbonates and Evaporites 21 133–143.

Geohydrology of the Navajo sandstone in western Kane, southwestern Garfield, and southeastern Iron counties, Utah

Science.gov (United States)

Freethey, G.W.

1988-01-01

The upper Navajo and Lamb Point aquifers in the Navajo Sandstone are the principal source of water for the city of Kanab, irrigation, stock, and for rural homes in the study area. Well logs and outcrop descriptions indicate the Navajo Sandstone consists of the Lamb Point Tongue and an unnamed upper member that are separated by the Tenney Canyon Tongue of the Kayenta Formation. The main Kayenta Formation underlies the Lamb Point Tongue. The Lamb Point Tongue and the upper member of the Navajo Sandstone are saturated and hydraulically connected through the Tenney Canyon Tongue. Available data indicate that precipitation percolates to the groundwater reservoir where the Navajo Sandstone crops out. Estimates of the rate of recharge at the outcrop range from 0.1 to as much as 2.8 in/yr. Water level data indicate that water moves from the upper member of the Navajo Sandstone, through the Tenney Canyon Tongue, and into the Lamb Point Tongue. Lateral flow is generally from the outcrop areas toward the incised canyons formed by tributaries of Kanab Creek and Johnson Wash. Direction and rate of groundwater movement and the location and character of the natural hydrologic boundaries in the northern part of the area where the Navajo Sandstone is buried cannot be determined conclusively without additional water level data. (Author 's abstract)

A New Multichelating Acid System for High-Temperature Sandstone Reservoirs

Directory of Open Access Journals (Sweden)

Nianyin Li

2015-01-01

Full Text Available Sandstone reservoir acidizing is a complex and heterogeneous acid-rock reaction process. If improper acid treatment is implemented, further damage can be induced instead of removing the initial plug, particularly in high-temperature sandstone reservoirs. An efficient acid system is the key to successful acid treatment. High-temperature sandstone treatment with conventional mud acid system faces problems including high acid-rock reaction rate, short acid effective distance, susceptibility to secondary damage, and serious corrosion to pipelines. In this paper, a new multichelating acid system has been developed to overcome these shortcomings. The acid system is composed of ternary weak acid, organic phosphonic chelating agent, anionic polycarboxylic acid chelating dispersant, fluoride, and other assisted additives. Hydrogen ion slowly released by multistage ionization in ternary weak acid and organic phosphonic within the system decreases the concentration of HF to achieve retardation. Chelating agent and chelating dispersant within the system inhibited anodic and cathodic reaction, respectively, to protect the metal from corrosion, while chelating dispersant has great chelating ability on iron ions, restricting the depolarization reaction of ferric ion and metal. The synergic effect of chelating agent and chelating dispersant removes sulfate scale precipitation and inhibits or decreases potential precipitation such as CaF2, silica gel, and fluosilicate. Mechanisms of retardation, corrosion-inhibition, and scale-removing features have been discussed and evaluated with laboratory tests. Test results indicate that this novel acid system has good overall performance, addressing the technical problems and improving the acidizing effect as well for high-temperature sandstone.

Architecture of an Upper Jurassic barrier island sandstone reservoir, Danish Central Graben:

DEFF Research Database (Denmark)

Johannessen, Peter N.; Nielsen, Lars H.; Nielsen, Lars

2010-01-01

An unusually thick (c. 88 m), transgressive barrier island and shoreface sandstone succession characterizes the Upper Jurassic Heno Formation reservoir of the Freja oil field situated on the boundary of Denmark and Norway. The development and preservation of such thick transgressive barrier island...... sands is puzzling since a barrier island typically migrates landwards during transgression and only a thin succession of back-barrier and shoreface sands is preserved. Investigation of the development and geometry of the Freja reservoir sandstones is problematic since the reservoir is buried c. 5 km...... and seismic resolution is inadequate for architectural analysis. Description of the reservoir sandstone bodies is thus based on sedimentological interpretation and correlation of seven wells, of which five were cored. Palaeotopography played a major role in the position and preservation of the thick reservoir...

Chapter 2. Assessment of undiscovered conventional oil and gas resources--Upper Jurassic-Lower Cretaceous Cotton Valley group, Jurassic Smackover interior salt basins total petroleum system, in the East Texas basin and Louisiana-Mississippi salt basins provinces.

Science.gov (United States)

Dyman, T.S.; Condon, S.M.

2006-01-01

The Jurassic Smackover Interior Salt Basins Total Petroleum System is defined for this assessment to include (1) Upper Jurassic Smackover Formation carbonates and calcareous shales and (2) Upper Jurassic and Lower Cretaceous Cotton Valley Group organic-rich shales. The Jurassic Smackover Interior Salt Basins Total Petroleum System includes four conventional Cotton Valley assessment units: Cotton Valley Blanket Sandstone Gas (AU 50490201), Cotton Valley Massive Sandstone Gas (AU 50490202), Cotton Valley Updip Oil and Gas (AU 50490203), and Cotton Valley Hypothetical Updip Oil (AU 50490204). Together, these four assessment units are estimated to contain a mean undiscovered conventional resource of 29.81 million barrels of oil, 605.03 billion cubic feet of gas, and 19.00 million barrels of natural gas liquids. The Cotton Valley Group represents the first major influx of clastic sediment into the ancestral Gulf of Mexico. Major depocenters were located in south-central Mississippi, along the Louisiana-Mississippi border, and in northeast Texas. Reservoir properties and production characteristics were used to identify two Cotton Valley Group sandstone trends across northern Louisiana and east Texas: a high-permeability blanket-sandstone trend and a downdip, low-permeability massive-sandstone trend. Pressure gradients throughout most of both trends are normal, which is characteristic of conventional rather than continuous basin-center gas accumulations. Indications that accumulations in this trend are conventional rather than continuous include (1) gas-water contacts in at least seven fields across the blanket-sandstone trend, (2) relatively high reservoir permeabilities, and (3) high gas-production rates without fracture stimulation. Permeability is sufficiently low in the massive-sandstone trend that gas-water transition zones are vertically extensive and gas-water contacts are poorly defined. The interpreted presence of gas-water contacts within the Cotton Valley

Discrimination, correlation, and provenance of Bed I tephrostratigraphic markers, Olduvai Gorge, Tanzania, based on multivariate analyses of phenocryst compositions

Science.gov (United States)

Habermann, Jörg M.; McHenry, Lindsay J.; Stollhofen, Harald; Tolosana-Delgado, Raimon; Stanistreet, Ian G.; Deino, Alan L.

2016-06-01

The chronology of Pleistocene flora and fauna, including hominin remains and associated Oldowan industries in Bed I, Olduvai Gorge, Tanzania, is primarily based on 40Ar/39Ar dating of intercalated tuffs and lavas, combined with detailed tephrostratigraphic correlations within the basin. Although a high-resolution chronostratigraphic framework has been established for the eastern part of the Olduvai Basin, the western subbasin is less well known due in part to major lateral facies changes within Bed I combined with discontinuous exposure. We address these correlation difficulties using the discriminative power of the chemical composition of the major juvenile mineral phases (augite, anorthoclase, plagioclase) from tuffs, volcaniclastic sandstones, siliciclastic units, and lavas. We statistically evaluate these compositions, obtained from electron probe micro-analysis, applying principal component analysis and discriminant analysis to develop discriminant models that successfully classify most Bed I volcanic units. The correlations, resulting from integrated analyses of all target minerals, provide a basin-wide Bed I chemostratigraphic framework at high lateral and vertical resolution, consistent with the known geological context, that expands and refines the geochemical databases currently available. Correlation of proximal ignimbrites at the First Fault with medial and distal Lower Bed I successions of the western basin enables assessment of lateral facies and thickness trends that confirm Ngorongoro Volcano as the primary source for Lower Bed I, whereas Upper Bed I sediment supply is mainly from Olmoti Volcano. Compositional similarity between Tuff IA, Bed I lava, and Mafic Tuffs II and III single-grain fingerprints, together with north- and northwestward thinning of Bed I lava, suggests a common Ngorongoro source for these units. The techniques applied herein improve upon previous work by evaluating compositional affinities with statistical rigor rather than

Unsaturated hydraulic behaviour of a permeable pavement: Laboratory investigation and numerical analysis by using the HYDRUS-2D model

Science.gov (United States)

Turco, Michele; Kodešová, Radka; Brunetti, Giuseppe; Nikodem, Antonín; Fér, Miroslav; Piro, Patrizia

2017-11-01

An adequate hydrological description of water flow in permeable pavement systems relies heavily on the knowledge of the unsaturated hydraulic properties of the construction materials. Although several modeling tools and many laboratory methods already exist in the literature to determine the hydraulic properties of soils, the importance of an accurate materials hydraulic description of the permeable pavement system, is increasingly recognized in the fields of urban hydrology. Thus, the aim of this study is to propose techniques/procedures on how to interpret water flow through the construction system using the HYDRUS model. The overall analysis includes experimental and mathematical procedures for model calibration and validation to assess the suitability of the HYDRUS-2D model to interpret the hydraulic behaviour of a lab-scale permeable pavement system. The system consists of three porous materials: a wear layer of porous concrete blocks, a bedding layers of fine gravel, and a sub-base layer of coarse gravel. The water regime in this system, i.e. outflow at the bottom and water contents in the middle of the bedding layer, was monitored during ten irrigation events of various durations and intensities. The hydraulic properties of porous concrete blocks and fine gravel described by the van Genuchten functions were measured using the clay tank and the multistep outflow experiments, respectively. Coarse gravel properties were set at literature values. In addition, some of the parameters (Ks of the concrete blocks layer, and α, n and Ks of the bedding layer) were optimized with the HYDRUS-2D model from water fluxes and soil water contents measured during irrigation events. The measured and modeled hydrographs were compared using the Nash-Sutcliffe efficiency (NSE) index (varied between 0.95 and 0.99) while the coefficient of determination R2 was used to assess the measured water content versus the modelled water content in the bedding layer (R2 = 0.81 ÷ 0.87) . The

Integrated prediction based on GIS for sandstone-type uranium deposits in the northwest of Ordos Basin

International Nuclear Information System (INIS)

Han Shaoyang; Ke Dan; Hu Shuiqing; Guo Qingyin; Hou Huiqun

2005-01-01

The integrated prediction model of sandstone-type uranium deposits and its integrated evaluation methods as well as flow of the work based on GIS are studied. A software for extracting metallogenic information is also developed. A multi-source exploring information database is established in the northwest of Ordos Basin, and an integrated digital mineral deposit prospecting model of sandstone-type uranium deposits is designed based on GIS. The authors have completed metallogenic information extraction and integrated evaluation of sandstone-type uranium deposits based on GIS in the study area. Research results prove that the integrated prediction of sandstone-type uranium deposits based on GIS may further delineate prospective target areas rapidly and improve the predictive precision. (authors)

Long-Term CO2 Exposure Experiments - Geochemical Effects on Brine-Saturated Reservoir Sandstone

Science.gov (United States)

Fischer, Sebastian; Zemke, Kornelia; Liebscher, Axel; Wandrey, Maren

2010-05-01

The injection of CO2 into deep saline aquifers is the most promising strategy for the reduction of CO2 emissions to the atmosphere via long-term geological storage. The study is part of the CO2SINK project conducted at Ketzin, situated 40 km west of Berlin. There, food grade CO2 has been pumped into the Upper Triassic Stuttgart Formation since June 2008. The main objective of the experimental program is to investigate the effects of long-term CO2 exposure on the physico-chemical properties of the reservoir rock. To achieve this goal, core samples from observation well Ktzi 202 have been saturated with synthetic brine and exposed to CO2 in high quality steel autoclaves at simulated reservoir P-T-conditions of 5.5 MPa and 40 ° C. The synthetic brine had a composition representative of the formation fluid (Förster et al., 2006) of 172.8 g/l NaCl, 8.0 g/l MgCl2×2H2O, 4.8 g/l CaCl2×2H2O and 0.6 g/l KCl. After 15 months, the first set of CO2-exposed samples was removed from the pressure vessels. Thin sections, XRD, SEM as well as EMP data were used to determine the mineralogical features of the reservoir rocks before and after the experiments. Additionally, NMR relaxation and MP was performed to measure poroperm and pore size distribution values of the twin samples. The analyzed samples are fine- to medium grained, moderately well- to well sorted and weakly consolidated sandstones. Quartz and plagioclase are the major components, while K-feldspar, hematite, white & dark mica, chlorite and illite are present in minor and varying amounts. Cements are composed of analcime, dolomite and anhydrite. Some samples show mm- to cm-scale cross-beddings. The laminae comprise lighter, quartz- and feldspar-dominated layers and dark-brownish layers with notably less quartz and feldspars. The results are consistent with those of Blaschke et al. (2008). The plagioclase composition indicates preferred dissolution of the Ca-component and a trend toward albite-rich phases or even pure

Tephrochronology of Bed II, Olduvai Gorge, Tanzania, and placement of the Oldowan-Acheulean transition.

Science.gov (United States)

McHenry, Lindsay J; Stanistreet, Ian G

2018-04-12

Tuffaceous marker beds, derived from volcanic products from the Ngorongoro Volcanic Highlands, help define a stratigraphic framework for the world-renowned fossil and stone tool record exposed at Olduvai Gorge, Tanzania. However, previous efforts to constrain this tuff record, especially for Olduvai Bed II, have been limited because of erosion, contamination, reworking, and the alteration of volcanic glass under saline-alkaline conditions. This paper applies previously defined geochemical and mineralogical "fingerprints" for several major Bed II marker tuffs, based on glass (where available) and phenocrysts more resistant to alteration (feldspar, hornblende, augite, and titanomagnetite), to tuffs from stratigraphic sections in the Olduvai Junction Area, including previously and recently excavated Acheulean and Oldowan sites (HWK EE (Locality (Loc) 42), EF-HR (Loc 12a), FLK (Loc 45), and MNK (Loc 88)). The Middle Bed II Bird Print Tuff (BPT) is found to be more compositionally variable than previously reported but is still valuable as a stratigraphic marker over short distances. The confirmation of blocks of Tuff IID in conglomerate helps constrain Upper Bed II stratigraphy at sites where in-situ tuffs are absent. This paper also compiles the results of published geochronological research, providing stratigraphic context and updating previously reported dates using a consistent 40 Ar/ 39 Ar reference standard age. The results of this work support the following paleoanthropologically relevant conclusions: 1) the early Acheulean site EF-HR (Loc 12a) is situated above the level of Hay's Tuff IIC, and thus sits in Upper rather than Middle Bed II, (2) the HWK EE (Loc 42) Oldowan site is constrained between Tuff IIA and Tuff IIB, just above the boundary between Lower and Middle Bed II, and 3) the Acheulean site at FLK W most likely lies within the Middle Augitic Sandstone, above Tuff IIB, similar to the placements by Leakey and Hay for the earliest Acheulean at Olduvai

National Uranium Resource Evaluation: Manhattan Quadrangle, Kansas

International Nuclear Information System (INIS)

Fair, C.L.; Smit, D.E.

1982-08-01

Surface reconnaissance and detailed subsurface studies were conducted in the Manhattan Quadrangle, Kansas, to evaluate uranium favorability using National Uranium Resource Evaluation criteria. These studies were designed in part to follow up airborne radiometric and hydrogeochemical and stream-sediment surveys. More than 600 well records were examined in the subsurface phase of the study. Results of these investigations indicate environments favorable for channel-controlled peneconcordant sandstone uranium deposits in Cretaceous rocks and for Wyoming roll-type deposits in Pennsylvanian sandstones. The Cretaceous sandstone environments exhibit such favorable characteristics as a bottom unconformity, high bed load, braided fluvial channels, large-scale cross-bedding, and one anomalous outcrop. The Pennsylvanian sandstone environments exhibit such favorable characteristics as arkosic cross-bedded sandstones, included pyrite and organic debris, interbedded shales, and gamma-ray log anomalies. Environments considered unfavorable for uranium deposits are limestone and dolomite environments, marine black shale environments, evaporative precipitate environments, and some fluvial sandstone environments. Environments considered unevaluated because not enough data were available include Precambrian plutonic, metamorphic, and sedimentary rocks, even though a large number of thin sections were available for study

Application research on remote sensing geology of sandstone-type uranium deposit in Yili basin

International Nuclear Information System (INIS)

Wang Huaiwu

2002-01-01

Based on remote sensing images and practical materials, and new ideas of laying particular emphasis on the research of regional geologic structures, and large in-situ leachable sandstone-type uranium deposits, applying the theory of plate tectonics, the author makes a comprehensive analysis on the uranium metallogenic environments, characteristics of regional geologic structures, the ore-controlling mechanism and factors, and uranium metallogeny. Authors propose that large interlayer oxidation zone sandstone-type uranium deposits are controlled by the combination of the stable block in Meso-Cenozoic compressive-shearing faulted subsided basin on the Yili multiphase massif in Tianshan paleo-island arc system, and the specific paleo-geographic environments and its' structural terrace'. The origin of hydrogenic sandstone-type uranium deposits is summarized by the authors as the 'mixing and neutralization' genetic model, and the 'eight ore-controlling factors merge into an organic whole' prospecting model. The above mentioned provides clear prospecting direction and new ideas for the forecasting direction for prospecting large sandstone-type uranium deposits

Study on integrated evaluation of sandstone-hosted uranium metallogenic potential in southern Yili basin

International Nuclear Information System (INIS)

Han Shaoyang; Ke Dan; Xu Jianguo; Zheng Enjiu; Li Shengxiang

2008-01-01

Plenty of geological data have been accumulated during mineral resource survey in China; under the guidance of new metallogenic theories, it is an important task of how to use these data most effectively for the new cycle uranium survey. In this paper, the flow of establishing the integrated mineral deposits prospecting model for sandstone-hosted uranium deposits is put forward. Based on studying geologic, hydrogeologic and regional geophysical field characteristics of representative uranium deposits No. 512 in southern Yili basin, its multi-source information descriptive model has been established, from which 512-type integrated prospecting models of sandstone-hosted uranium orefield and deposits are summarized. According to the established integrated prospecting models, the metallogenic information extraction of sandstone-hosted uranium deposits has completed in the study area. Finally, the integrated quantitative evaluation of sandstone-hosted uranium metallogenic potential is performed by using the evidence weighing method to integrate middle scale multi-source metallogenic information in the southern Yili basin, and good prediction effect is obtained. (authors)

Experimental and Numerical Investigations on Strength and Deformation Behavior of Cataclastic Sandstone

Science.gov (United States)

Zhang, Y.; Shao, J. F.; Xu, W. Y.; Zhao, H. B.; Wang, W.

2015-05-01

This work is devoted to characterization of the deformation and strength properties of cataclastic sandstones. Before conducting mechanical tests, the physical properties were first examined. These sandstones are characterized by a loose damaged microstructure and poorly cemented contacts. Then, a series of mechanical tests including hydrostatic, uniaxial, and triaxial compression tests were performed to study the mechanical strength and deformation of the sandstones. The results obtained show nonlinear stress-strain responses. The initial microcracks are closed at hydrostatic stress of 2.6 MPa, and the uniaxial compressive strength is about 0.98 MPa. Under triaxial compression, there is a clear transition from volumetric compressibility to dilatancy and a strong dependency on confining pressure. Based on the experimental evidence, an elastoplastic model is proposed using a linear yield function and a nonassociated plastic potential. There is good agreement between numerical results and experimental data.

Single- and two-phase flow simulation based on equivalent pore network extracted from micro-CT images of sandstone core.

Science.gov (United States)

Song, Rui; Liu, Jianjun; Cui, Mengmeng

2016-01-01

Due to the intricate structure of porous rocks, relationships between porosity or saturation and petrophysical transport properties classically used for reservoir evaluation and recovery strategies are either very complex or nonexistent. Thus, the pore network model extracted from the natural porous media is emphasized as a breakthrough to predict the fluid transport properties in the complex micro pore structure. This paper presents a modified method of extracting the equivalent pore network model from the three-dimensional micro computed tomography images based on the maximum ball algorithm. The partition of pore and throat are improved to avoid tremendous memory usage when extracting the equivalent pore network model. The porosity calculated by the extracted pore network model agrees well with the original sandstone sample. Instead of the Poiseuille's law used in the original work, the Lattice-Boltzmann method is employed to simulate the single- and two- phase flow in the extracted pore network. Good agreements are acquired on relative permeability saturation curves of the simulation against the experiment results.

The controlling role of positive structures over the metallogenesis and emplacement of inter layer oxidation sandstone type uranium deposits

International Nuclear Information System (INIS)

Gu Kangheng; Chen Zuyi

2010-01-01

The positive structures in this paper mean the geological structures related to the occurrence of U-metallogenic zones or U-deposit such as anticlines, uplifts and uplifted fault-blocks. Occurrence features of interlayer oxidation sandstone type deposit at the southern margin of Yili basin and southwestern margin of Turpan-Hami basin, the northeastern margin of Jiudong basin illustrate that the sandstone-hosted uranium deposits, the U-mineralized sections and the uranium occurrences are always selectively emplaced on/in positive structures. The reasons for this lie in the formation mechanism of sandstone-hosted U-deposits. The positive structures raised the elevation of ore-hosting sandstone horizon and make it close to ground surface or exposed at the ground surface, which result in the infiltration of uranium and oxygen bearing groundwater from recharge area into host sandstone horizon, and the interlayer oxidation of host sandstone, as well as the dissolution and the migration of uranium in host sandstone, and the reduction mineralization at the oxidation-reduction interface. Sufficient attention should be paid to the controlling role of positive structures over the metallogenesis and emplacement of sandstone-hosted uranium deposits. They could act as an important criterion for recognizing and prognosticating potential uranium mineralized areas in uranium metallogenic zones or uranium-productive sedimentary basins. (authors)

Coupled hydrology and biogeochemistry of Paleocene–Eocene coal beds, northern Gulf of Mexico

Science.gov (United States)

McIntosh, Jennifer C.; Warwick, Peter D.; Martini, Anna M.; Osborn, Stephen G.

2010-01-01

Thirty-six formation waters, gas, and microbial samples were collected and analyzed from natural gas and oil wells producing from the Paleocene to Eocene Wilcox Group coal beds and adjacent sandstones in north-central Louisiana, USA, to investigate the role hydrology plays on the generation and distribution of microbial methane. Major ion chemistry and Cl−Br relations of Wilcox Group formation waters suggest mixing of freshwater with halite-derived brines. High alkalinities (up to 47.8 meq/L), no detectable SO4, and elevated δ13C values of dissolved inorganic carbon (up to 20.5‰ Vienna Peedee belemnite [VPDB]) and CO2 (up to 17.67‰ VPDB) in the Wilcox Group coals and adjacent sandstones indicate the dominance of microbial methanogenesis. The δ13C and δD values of CH4, and carbon isotope fractionation of CO2 and CH4, suggest CO2 reduction is the major methanogenic pathway. Geochemical indicators for methanogenesis drop off significantly at chloride concentrations above ∼1.7 mol/L, suggesting that high salinities inhibit microbial activity at depths greater than ∼1.6 km. Formation waters in the Wilcox Group contain up to 1.6% modern carbon (A14C) to at least 1690 m depth; the covariance of δD values of co-produced H2O and CH4 indicate that the microbial methane was generated in situ with these Late Pleistocene or younger waters. The most enriched carbon isotope values for dissolved inorganic carbon (DIC) and CO2, and highest alkalinities, were detected in Wilcox Group sandstone reservoirs that were CO2 flooded in the 1980s for enhanced oil recovery, leading to the intriguing hypothesis that CO2 sequestration may actually enhance methanogenesis in organic-rich formations.

Computer model for determining fracture porosity and permeability in the Conasauga Group, Oak Ridge National Laboratory, Tennessee

International Nuclear Information System (INIS)

Sledz, J.J.; Huff, D.D.

1981-04-01

Joint orientations for the shale and siltstone beds of the Conasauga Group were measured from outcrop exposures on the Oak Ridge National Laboratory Reservation. The data collected from two strike belts (structural trends) were analyzed with the use of the computer and subdivided into individual joint sets. The joint set patterns in the Northern outcrop belt were too complex for orientation prediction; joint formation is believed to be influenced by polyphase deformation. The Southern Conasauga Belt contains an orthogonal joint set consisting of strike and a-c joints in all outcrops measured. These are believed to be tension joints formed during thrust sheet emplacement. Joint length and spacing, measured in the field, were found to be extremely variable within each exposure and highly dependent upon surficial weathering. The measurements from all locations were combined for detailed analysis and trend prediction. Results showed that the joint length and spacing increased with increasing bed thickness in the siltstone, while the bed thickness variations in the shale had little effect on the joints. A computer model was developed by combining the joint orientation, joint spacing, and joint length data collected in the field with subsurface drill core information for the purpose of calculating the fracture porosity and permeability of the rocks. The joint gap width was measured from both outcrop and subsurface samples with ranges from 0.1 mm to 0.7 mm in the siltstones and less than 0.2 mm in the shales. The value for the joint gap width was found to be the major factor in the fracture porosity and permeability calculation

Quantifying the effect of squirt flow dispersion from compliant clay porosity in clay bearing sandstones

DEFF Research Database (Denmark)

Sørensen, Morten Kanne; Fabricius, Ida Lykke

2013-01-01

Compliant porosity in the form of cracks is known to cause significant attenuation and velocity dispersion through pore pressure gradients and consequent relaxation, dubbed squirt flow. Squirt flow from cracks vanish at high confining stress due to crack closing. Studies on clay bearing sandstones......-squirt flow on the bulk modulus of a clay bearing sandstone. The predicted magnitude of the clay-squirt effect on the bulk modulus is compared with experimental data. The clay-squirt effect is found to possibly account for a significant portion of the deviances from Gassmann fluid substitution in claybearing...... sandstones....

Architectural evidence of dune collapse in the Navajo Sandstone, Zion National Park, Utah

Science.gov (United States)

Ford, Colby; Bryant, Gerald; Nick, Kevin E.

2016-10-01

The Canyon Overlook Trail of Zion National Park follows an outcrop of Navajo Sandstone, which displays a uniquely well-exposed assemblage of features associated with failure of the lee face of a large eolian dune, and run-out over an expanse of interdune sediments downwind of that bedform. Exposed features include dramatic folds in the interdune succession and a stacked series of thrust sheets incorporating both interdune and overlying dune deposits. Thrust surfaces display consistent strikes, parallel to those of undeformed foresets, and incorporate zones of brittle failure and fluid deformation, including folds overturned in the direction of foreset dip. These features correspond to predictions made by a previous researcher's model of dune collapse, formulated from less fortuitously exposed architectures in the Navajo Sandstone. Unlike the previous model, however, this site preserves distinct indications that the bulk of deformed material accumulated above the level of the contemporary interdune surface, in an aggradational succession. Paleotopographic reconstruction, based on preserved facies relationships at this site, indicates the presence of a large dune, partially encroached upon a well-developed wet interdune succession, made up of two half-meter carbonate mud layers, separated by a meter of medium-grained sand. Trapping of pore water pressure between these mud layers during liquefaction reduced shear strength in this interval, facilitating the collapse of the lee face of the upwind dune into the interdune area, and transmitted resultant shear forces to distal portions of the interdune expanse, in the shallow subsurface. Shear failure developed along bedding planes in the horizontally laminated carbonate muds, which provided both lubrication of the shear surfaces and structural support for the preservation of coherent thrust sheets during production of an imbricated succession of shear zones in the toe portion of the slump. Individual shear surfaces

Multielement statistical evidence for uraniferous hydrothermal activity in sandstones overlying the Phoenix uranium deposit, Athabasca Basin, Canada

Science.gov (United States)

Chen, Shishi; Hattori, Keiko; Grunsky, Eric C.

2018-04-01

The Phoenix U deposit, with indicated resources of 70.2 M lb U3O8, occurs along the unconformity between the Proterozoic Athabasca Group sandstones and the crystalline basement rocks. Principal component analysis (PCA) is applied to the compositions of sandstones overlying the deposit. Among PCs, PC1 accounts for the largest variability of U and shows a positive association of U with rare earth elements (REEs) + Y + Cu + B + Na + Mg + Ni + Be. The evidence suggests that U was dispersed into sandstones together with these elements during the uraniferous hydrothermal activity. Uranium shows an inverse association with Zr, Hf, Th, Fe, and Ti. Since they are common in detrital heavy minerals, such heavy minerals are not the major host of U. The elements positively associated with U are high in concentrations above the deposit, forming a "chimney-like" or "hump-like" distribution in a vertical section. Their enrichment patterns are explained by the ascent of basement fluids through faults to sandstones and the circulation of basinal fluids around the deposit. The Pb isotope compositions of whole rocks are similar to expected values calculated from the concentrations of U, Th, and Pb except for sandstones close to the deposit. The data suggest that in situ decay of U and Th is responsible for the Pb isotope compositions of most sandstones and that highly radiogenic Pb dispersed from the deposit to the proximal sandstones long after the mineralization. This secondary dispersion is captured in PC8, which has low eigenvalue. The data suggests that the secondary dispersion has minor effect on the overall lithogeochemistry of sandstones.

Controls on the variability of net infiltration to desert sandstone

Science.gov (United States)

Heilweil, Victor M.; McKinney, Tim S.; Zhdanov, Michael S.; Watt, Dennis E.

2007-01-01

As populations grow in arid climates and desert bedrock aquifers are increasingly targeted for future development, understanding and quantifying the spatial variability of net infiltration becomes critically important for accurately inventorying water resources and mapping contamination vulnerability. This paper presents a conceptual model of net infiltration to desert sandstone and then develops an empirical equation for its spatial quantification at the watershed scale using linear least squares inversion methods for evaluating controlling parameters (independent variables) based on estimated net infiltration rates (dependent variables). Net infiltration rates used for this regression analysis were calculated from environmental tracers in boreholes and more than 3000 linear meters of vadose zone excavations in an upland basin in southwestern Utah underlain by Navajo sandstone. Soil coarseness, distance to upgradient outcrop, and topographic slope were shown to be the primary physical parameters controlling the spatial variability of net infiltration. Although the method should be transferable to other desert sandstone settings for determining the relative spatial distribution of net infiltration, further study is needed to evaluate the effects of other potential parameters such as slope aspect, outcrop parameters, and climate on absolute net infiltration rates.

INAA and petrological study of sandstones from Khmer temples in Angkor

International Nuclear Information System (INIS)

Kucera, J.; Kranda, K.; Novak, J.K.; Poncar, J.; Krausova, I.; Soukal, L.

2009-01-01

INAA was used to determine 35 major, minor and trace elements in sandstone samples taken from building blocks of 21 Khmer temples in Angkor, Cambodia. The sandstone samples were also characterized by conventional optical microscopy, X-ray diffraction analysis and electron microprobe analysis. The aim of this work was to examine the hypothesis that a particular elemental and/or mineral composition of the building materials can be characteristic of a particular architectural style/building period in the history of constructing the Angkor monuments. Preliminary results of this study are presented

A new bee species that excavates sandstone nests

Science.gov (United States)

Many wonder why animals act in seemingly injurious ways. Understanding the behavior of pollinators such as bees is especially important because of the necessary ecosystem service they provide. The new species Anthophora pueblo, discovered excavating sandstone nests, provides a model system for addre...

Mechanical Behavior of Red Sandstone under Incremental Uniaxial Cyclical Compressive and Tensile Loading

Directory of Open Access Journals (Sweden)

Baoyun Zhao

2017-01-01

Full Text Available Uniaxial experiments were carried out on red sandstone specimens to investigate their short-term and creep mechanical behavior under incremental cyclic compressive and tensile loading. First, based on the results of short-term uniaxial incremental cyclic compressive and tensile loading experiments, deformation characteristics and energy dissipation were analyzed. The results show that the stress-strain curve of red sandstone has an obvious memory effect in the compressive and tensile loading stages. The strains at peak stresses and residual strains increase with the cycle number. Energy dissipation, defined as the area of the hysteresis loop in the stress-strain curves, increases nearly in a power function with the cycle number. Creep test of the red sandstone was also conducted. Results show that the creep curve under each compressive or tensile stress level can be divided into decay and steady stages, which cannot be described by the conventional Burgers model. Therefore, an improved Burgers creep model of rock material is constructed through viscoplastic mechanics, which agrees very well with the experimental results and can describe the creep behavior of red sandstone better than the Burgers creep model.

The effects of impure CO2 on reservoir sandstones: results from mineralogical and geomechanical experiments

Science.gov (United States)

Marbler, H.; Erickson, K. P.; Schmidt, M.; Lempp, Ch.; Pöllmann, H.

2012-04-01

An experimental study of the behaviour of reservoir sandstones from deep saline aquifers during the injection and geological storage of CO2 with the inherent impurities SOX and NOX is part of the German national project COORAL*. Sample materials were taken from outcrops of possible reservoir formations of Rotliegend and Bunter Sandstones from the North German Basin. A combination of mineralogical alteration experiments and geomechanical tests was carried out on these rocks to study the potential effects of the impurities within the CO2 pore fluid. Altered rock samples after the treatment with CO2 + SOX/NOX in an autoclave system were loaded in a triaxial cell under in-situ pressure and temperature conditions in order to estimate the modifications of the geomechanical rock properties. Mineralogical alterations were observed within the sandstones after the exposure to impure supercritical (sc)CO2 and brine, mainly of the carbonatic, but also of the silicatic cements, as well as of single minerals. Besides the partial solution effects also secondary carbonate and minor silicate mineral precipitates were observed within the pore space of the treated sandstones. These alterations affect the grain structure of the reservoir rock. Results of geomechanical experiments with unaltered sandstones show that the rock strength is influenced by the degree of rock saturation before the experiment and the chemical composition of the pore fluid (scCO2 + SOX + NOX). After long-term autoclave treatment with impure scCO2, the sandstone samples exhibit modified strength parameters and elastic deformation behaviour as well as changes in porosity compared to untreated samples. Furthermore, the injected fluid volume into the pore space of sandstones from the same lithotype varies during triaxial loading depending on the chemistry of the pore fluid. CO2 with NOX and SOX bearing fluid fills a significantly larger proportion of the sandstone pore space than brine with pure scCO2. * The

Dinosaur Footprints and Other Ichnofauna from the Cretaceous Kem Kem Beds of Morocco

Science.gov (United States)

Ibrahim, Nizar; Varricchio, David J.; Sereno, Paul C.; Wilson, Jeff A.; Dutheil, Didier B.; Martill, David M.; Baidder, Lahssen; Zouhri, Samir

2014-01-01

We describe an extensive ichnofossil assemblage from the likely Cenomanian-age ‘lower’ and ‘upper’ units of the ‘Kem Kem beds’ in southeastern Morocco. In the lower unit, trace fossils include narrow vertical burrows in cross-bedded sandstones and borings in dinosaur bone, with the latter identified as the insect ichnotaxon Cubiculum ornatus. In the upper unit, several horizons preserve abundant footprints from theropod dinosaurs. Sauropod and ornithischian footprints are much rarer, similar to the record for fossil bone and teeth in the Kem Kem assemblage. The upper unit also preserves a variety of invertebrate traces including Conichnus (the resting trace of a sea-anemone), Scolicia (a gastropod trace), Beaconites (a probable annelid burrow), and subvertical burrows likely created by crabs for residence and detrital feeding on a tidal flat. The ichnofossil assemblage from the Upper Cretaceous Kem Kem beds contributes evidence for a transition from predominantly terrestrial to marine deposition. Body fossil and ichnofossil records together provide a detailed view of faunal diversity and local conditions within a fluvial and deltaic depositional setting on the northwestern coast of Africa toward the end of the Cretaceous. PMID:24603467

Super enhanced permeability and retention (SUPR) effects in tumors following near infrared photoimmunotherapy

Science.gov (United States)

Kobayashi, Hisataka; Choyke, Peter L.

2016-06-01

To date, the delivery of nano-sized therapeutic agents to cancers largely relies on enhanced permeability and retention (EPR) effects that are caused by the leaky nature of cancer vasculature. However, nano-sized agents delivered in this way have demonstrated limited success in oncology due to the relatively small magnitude of the EPR effect. For achieving superior delivery of nano-sized agents, super-enhanced permeability and retention (SUPR) effects are needed. Near infrared photo-immunotherapy (NIR-PIT) is a recently reported therapy that treats tumors with light therapy and subsequently causes an increase in nano-drug delivery up to 24-fold compared with untreated tumors in which only the EPR effect is present. SUPR effects could enhance delivery into tumor beds of a wide variety of nano-sized agents including particles, antibodies, and protein binding small molecular agents. Therefore, taking advantage of the SUPR effects after NIR-PIT may be a promising avenue to utilize a wide variety of nano-drugs in a highly effective manner.

Modeling of carbon sequestration in coal-beds: A variable saturated simulation

International Nuclear Information System (INIS)

Liu Guoxiang; Smirnov, Andrei V.

2008-01-01

Storage of carbon dioxide in deep coal seams is a profitable method to reduce the concentration of green house gases in the atmosphere while the methane as a byproduct can be extracted during carbon dioxide injection into the coal seam. In this procedure, the key element is to keep carbon dioxide in the coal seam without escaping for a long term. It is depended on many factors such as properties of coal basin, fracture state, phase equilibrium, etc., especially the porosity, permeability and saturation of the coal seam. In this paper, a variable saturation model was developed to predict the capacity of carbon dioxide sequestration and coal-bed methane recovery. This variable saturation model can be used to track the saturation variability with the partial pressures change caused by carbon dioxide injection. Saturation variability is a key factor to predict the capacity of carbon dioxide storage and methane recovery. Based on this variable saturation model, a set of related variables including capillary pressure, relative permeability, porosity, coupled adsorption model, concentration and temperature equations were solved. From results of the simulation, historical data agree with the variable saturation model as well as the adsorption model constructed by Langmuir equations. The Appalachian basin, as an example, modeled the carbon dioxide sequestration in this paper. The results of the study and the developed models can provide the projections for the CO 2 sequestration and methane recovery in coal-beds within different regional specifics

Experimental Investigation on Shock Mechanical Properties of Red Sandstone under Preloaded 3D Static Stresses

Directory of Open Access Journals (Sweden)

Niu Yong

2015-11-01

Full Text Available Triaxial impact mechanical performance experiment was performed to study the mechanical properties of red sandstone subjected to three-dimensional (3D coupled static and dynamic loads, i.e., three confining pressures (0, 5, and 10 MPa and three axial pressures (11, 27, and 43 MPa. A modified 3D split Hopkinson pressure bar testing system was used. The change trend in the deformation of red sandstone and the strength and failure modes under axial pressures and confining pressures were analyzed. Results show that, when the confining pressure is constant, the compressive strength, secant modulus, and energy absorbed per unit volume of red sandstone initially increases and subsequently decreases, whereas the average strain rate exhibits an opposite trend. When the axial pressure is constant, both the compressive strength and secant modulus of red sandstone are enhanced, but the average strain rate is decreased with increasing confining pressure. The energy absorbed per unit volume is initially increased and subsequently decreased as the confining pressure increases. Red sandstone exhibits a cone-shaped compression–shear failure mode under the 3D coupled static and dynamic loads. The conclusions serve as theoretical basis on the mechanical properties of deep medium-strength rock under a high ground stress and external load disturbance condition

The role of mineral heterogeneity on the hydrogeochemical response of two fractured reservoir rocks in contact with dissolved CO2

Science.gov (United States)

Garcia Rios, Maria; Luquot, Linda; Soler, Josep M.; Cama, Jordi

2017-04-01

In this study we compare the hydrogeochemical response of two fractured reservoir rocks (limestone composed of 100 wt.% calcite and sandstone composed of 66 wt.% calcite, 28 wt.% quartz and 6 wt.% microcline) in contact with CO2-rich sulfate solutions. Flow-through percolation experiments were performed using artificially fractured limestone and sandstone cores and injecting a CO2-rich sulfate solution under a constant volumetric flow rate (from 0.2 to 60 mL/h) at P = 150 bar and T = 60 °C. Measurements of the pressure difference between the inlet and the outlet of the samples and of the aqueous chemistry enabled the determination of fracture permeability changes and net reaction rates. Additionally, X-ray computed microtomography (XCMT) was used to characterize and localized changes in fracture volume induced by dissolution and precipitation reactions. In all reacted cores an increase in fracture permeability and in fracture volume was always produced even when gypsum precipitation happened. The presence of inert silicate grains in sandstone samples favored the occurrence of largely distributed dissolution structures in contrast to localized dissolution in limestone samples. This phenomenon promoted greater dissolution and smaller precipitation in sandstone than in limestone experiments. As a result, in sandstone reservoirs, the larger increase in fracture volume as well as the more extended distribution of the created volume would favor the CO2 storage capacity. The different distribution of created volume between limestone and sandstone experiments led to a different variation in fracture permeability. The progressive stepped permeability increase for sandstone would be preferred to the sharp permeability increase for limestone to minimize risks related to CO2 injection, favor capillary trapping and reduce energetic storage costs. 2D reactive transport simulations that reproduce the variation in aqueous chemistry and the fracture geometry (dissolution pattern

Notional Permeability

NARCIS (Netherlands)

Kik, R.; Van den Bos, J.P.; Maertens, J.; Verhagen, H.J.; Van der Meer, J.W.

2012-01-01

Different layer design of a rock slope and under layers has a large effect on the strengths on the rock slope itself. In the stability formula developed of VAN DER MEER [1988] this effect is represented by the term Notional Permeability with symbol P. A more open, or permeable, structure underneath

Application of Rock-Eval pyrolysis to the detection of hydrocarbon property in sandstone-type uranium deposits

International Nuclear Information System (INIS)

Sun Ye; Li Ziying; Guo Qingyin; Xiao Xinjian

2006-01-01

Rock-Eval pyrolysis is introduced into the research of uranium geology by means of oil-gas geochemical evaluation. Hydrocarbon (oil-gas) components in DS sandstone-type uranium deposit are detected quantitatively. Through analyzing the oil-gas bearing categories of the uranium-bearing sandstones, the internal relationships between the uranium deposit and the oil-gas are revealed. Rock-Eval pyrolysis is an effective method to study the interaction between inorganic and organic matters, and should be extended to the study of sandstone-type uranium deposits. (authors)

An interpretation of core and wireline logs for the Petrophysical evaluation of Upper Shallow Marine sandstone reservoirs of the Bredasdorp Basin, offshore South Africa

Science.gov (United States)

Magoba, Moses; Opuwari, Mimonitu

2017-04-01

This paper embodies a study carried out to assess the Petrophysical evaluation of upper shallow marine sandstone reservoir of 10 selected wells in the Bredasdorp basin, offshore, South Africa. The studied wells were selected randomly across the upper shallow marine formation with the purpose of conducting a regional study to assess the difference in reservoir properties across the formation. The data sets used in this study were geophysical wireline logs, Conventional core analysis and geological well completion report. The physical rock properties, for example, lithology, fluid type, and hydrocarbon bearing zone were qualitatively characterized while different parameters such as volume of clay, porosity, permeability, water saturation ,hydrocarbon saturation, storage and flow capacity were quantitatively estimated. The quantitative results were calibrated with the core data. The upper shallow marine reservoirs were penetrated at different depth ranging from shallow depth of about 2442m to 3715m. The average volume of clay, average effective porosity, average water saturation, hydrocarbon saturation and permeability range from 8.6%- 43%, 9%- 16%, 12%- 68% , 32%- 87.8% and 0.093mD -151.8mD respectively. The estimated rock properties indicate a good reservoir quality. Storage and flow capacity results presented a fair to good distribution of hydrocarbon flow.

Low field NMR surface relaxivity studies of chalk and argillaceous sandstones

DEFF Research Database (Denmark)

Katika, Konstantina; Fordsmand, Henrik; Fabricius, Ida Lykke

2017-01-01

the accuracy of predictions of petrophysical properties of various rocks with the use of NMR spectrometry. We perform laboratory transverse relaxation (T2) measurements on water saturated Gorm field chalk, Stevns Klint chalk, Solsort field greensand and Berea sandstone. These rocks are of particular interest...... field chalk and Solsort field greensand have higher ρ at higher Larmor frequency. By contrast, ρ of the purely calcitic Stevns chalk and quartzitic Berea sandstone proved not to be affected by the changes in frequency. T2 distributions at temperatures ranging from 10 °C to 60 °C provided comparison...

High-permeability criterion for BCS classification: segmental/pH dependent permeability considerations.

Science.gov (United States)

Dahan, Arik; Miller, Jonathan M; Hilfinger, John M; Yamashita, Shinji; Yu, Lawrence X; Lennernäs, Hans; Amidon, Gordon L

2010-10-04

The FDA classifies a drug substance as high-permeability when the fraction of dose absorbed (F(abs)) in humans is 90% or higher. This direct correlation between human permeability and F(abs) has been recently controversial, since the β-blocker sotalol showed high F(abs) (90%) and low Caco-2 permeability. The purpose of this study was to investigate the scientific basis for this disparity between permeability and F(abs). The effective permeabilities (P(eff)) of sotalol and metoprolol, a FDA standard for the low/high P(eff) class boundary, were investigated in the rat perfusion model, in three different intestinal segments with pHs corresponding to the physiological pH in each region: (1) proximal jejunum, pH 6.5; (2) mid small intestine, pH 7.0; and (3) distal ileum, pH 7.5. Both metoprolol and sotalol showed pH-dependent permeability, with higher P(eff) at higher pH. At any given pH, sotalol showed lower permeability than metoprolol; however, the permeability of sotalol determined at pH 7.5 exceeded/matched metoprolol's at pH 6.5 and 7.0, respectively. Physicochemical analysis based on ionization, pK(a) and partitioning of these drugs predicted the same trend and clarified the mechanism behind these observed results. Experimental octanol-buffer partitioning experiments confirmed the theoretical curves. An oral dose of metoprolol has been reported to be completely absorbed in the upper small intestine; it follows, hence, that metoprolol's P(eff) value at pH 7.5 is not likely physiologically relevant for an immediate release dosage form, and the permeability at pH 6.5 represents the actual relevant value for the low/high permeability class boundary. Although sotalol's permeability is low at pH 6.5 and 7.0, at pH 7.5 it exceeds/matches the threshold of metoprolol at pH 6.5 and 7.0, most likely responsible for its high F(abs). In conclusion, we have shown that, in fact, there is no discrepancy between P(eff) and F(abs) in sotalol's absorption; the data emphasize that

The influence of climate on early and burial diagenesis of Triassic and Jurassic sandstones from the Norwegian – Danish Basin

DEFF Research Database (Denmark)

Weibel, Rikke; Olivarius, Mette; Kjøller, Claus

2017-01-01

Climate changes preserved in sandstones are documented by comparing the sediment composition and early diagenetic changes in sandstones deposited during arid to semi-arid conditions, the Skagerrak Formation, with sandstones of the Gassum Formation deposited in a humid well-vegetated environment...

Characterization of samples of a cement-borehole plug in bedded evaporites

International Nuclear Information System (INIS)

Scheetz, B.E.; Grutzeck, M.W.; Wakeley, L.D.; Roy, D.M.

1979-07-01

This report describes the laboratory characterization of a section of an eighteen-year-old cement-based plug emplaced to seal a four-inch (ten-centimeter) borehole in the Salado Formation near Carlsbad, NM. The dominantly halite salt strata contain a horizon rich in potassium-bearing minerals such as langbeinite, in the plug region. Other host rock minerals identified include illite, kainite, magnesite, syngenite and polyhalite. Identified in the plug were: the cement phase calcium silicate hydrate (C-S-H having an intermediate degree of crystallinity), Friedel's salt, halite, sylvite and portlandite. The plug, though intact, unfractured on a macroscale, and forming an adequate physical bond with the salt formation, was weak and permeable relative to the surrounding bedded salt. Characterization of the plug and rock was carried out by a combination of measurements: compressive strength, permeability, density and porosity, thermal measurements (DTA, TGA), x-ray diffractometry, SEM and optical (including thin section) microscopy, and energy-dispersive x-ray analysis for chemical composition

Using multiple bed load measurements: Toward the identification of bed dilation and contraction in gravel-bed rivers

Science.gov (United States)

Marquis, G. A.; Roy, A. G.

2012-02-01

This study examines bed load transport processes in a small gravel-bed river (Béard Creek, Québec) using three complementary methods: bed elevation changes between successive floods, bed activity surveys using tags inserted into the bed, and bed load transport rates from bed load traps. The analysis of 20 flood events capable of mobilizing bed material led to the identification of divergent results among the methods. In particular, bed elevation changes were not consistent with the bed activity surveys. In many cases, bed elevation changes were significant (1 to 2 times the D50) even if the bed surface had not been activated during the flood, leading to the identification of processes of bed dilation and contraction that occurred over 10% to 40% of the bed surface. These dynamics of the river bed prevent accurate derivation of bed load transport rates from topographic changes, especially for low magnitude floods. This paper discusses the mechanisms that could explain the dilation and contraction of particles within the bed and their implications in fluvial dynamics. Bed contraction seems to be the result of the winnowing of the fine sediments under very low gravel transport. Bed dilation seems to occur on patches of the bed at the threshold of motion where various processes such as fine sediment infiltration lead to the maintenance of a larger sediment framework volume. Both processes are also influenced by flood history and the initial local bed state and in turn may have a significant impact on sediment transport and morphological changes in gravel-bed rivers.

Stable isotopic mass balance in sandstone-shale couplets. An example from the Neogene Pannonian Basin

International Nuclear Information System (INIS)

Matyas, J.; Geologisches Institut.

1996-01-01

Oxygen isotopic ratios of carbonate cements in the Neogene sandstones of the Pannonian Basin show distinct variations: early calcites 3-6 per mille lighter than the late calcites from the same location and depth. This shift is thought to be related to the isotopically heavy oxygen released from the mixed-layer illite/smectite during illitisation. For sandstones dominated by compactional flow, closed system mass balance calculations predict an isotopic shift comparable to that deducted from petrographic and geochemical observations. The model suggests that variations of geothermal gradient has little effect on isotopic evolution; much more significant is the sandstone: shale ratio in the couplets. (author)

Microbial EOR technology; Biseibutsu EOR gijutsu no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Taguchi, M.; Yonebayashi, E. [Tech. Research Center, Japan National Oil Corp., Tokyo (Japan)

1995-11-10

This paper describes attempts of establishing an oil recovery technology utilizing microorganisms and of aiming at improving the practicability of that technology. Fiscal 1994 has investigated effects of inorganic salts existing in reservoir beds and NaCl concentrations on proliferation of microorganisms and production of metabolites. The investigation was intended to discuss applicability of microorganisms to environments that are brought closer to actual field conditions. Furthermore, a core sweeping test using sandstone was carried out on the fiscal 1992 separated bacteria, the 4118 bacteria, that has high surfactant production capability. In addition, a sand pack was used to perform a flooding experiment under conditions of 50{degree}C and 50 KSC to evaluate functionality of microorganisms when environments in the reservoir bed are simulated with respect to pressures and temperatures. An oil recovering experiment was carried out using a sandstone with a diameter of 1.5 inches, a length of 1.0 foot and permeability of 600 md, and using Bacillus subtilis 4118 bacteria which attained the lowest interfacial tension among the bacteria examined. A recovery rate of 4.4% Sor was derived in the experiment. A recovery rate of 29.0% Sor at maximum was obtained when Bacillus licheniformis 18-2-a bacteria was supplied into a sand pack filled with silica sand. 20 figs., 7 tabs.

Diagenesis and reservoir properties of Cretaceous-Lower Tertiary sandstones: the GANT-1 well, western Nuussuaq, central West Greenland

Energy Technology Data Exchange (ETDEWEB)

Kierkegaard, Thomas

1998-08-01

The main purpose of this study is to describe the diagenetic alterations occurring in the Cretaceous to Lower Paleocene sedimentary succession of the GANT-1 well, and to determine the diagenetic and detrital factors which control present porosity and permeability. The GANT-1 well is located on north-western Nuussuaq, central West Greenland. The West Greenland margin is a continental margin subdivided into linked basins where Cretaceous to Lower Tertiary and probably older sediments have been deposited. In the Nuussuaq area these sediments are overlain by a succession of Early Tertiary basaltic volcanic rocks which reaches a combined thickness of around 2-2.5 km. Although the reservoir properties of the sandstone intervals in the GANT-1 and GANE-1 wells are generally relatively poor, it is suggested that moderate to good properties may be found in certain intervals within the Maastrichtian-Paleocene succession. However, the reason for the locally enhanced reservoir properties in GANT-1 was not clarified by this study due to the lack of regional petrographical data. (EG) EFP-96. 41 refs., 3 maps

Properties and durability assessment of glauconitic sandstone: A case study on Zamel sandstone from Bohemian Cretaceous Basin (Czech Republic)

Czech Academy of Sciences Publication Activity Database

Martinec, Petr; Vavro, M.; Ščučka, Jiří; Mašláň, M.

2010-01-01

Roč. 115, 3/4 (2010), s. 175-181 ISSN 0013-7952 R&D Projects: GA ČR GP101/07/P512; GA ČR(CZ) GA103/07/1662 Institutional research plan: CEZ:AV0Z30860518 Keywords : building stone * sandstone * physical properties Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.442, year: 2010 http://www.sciencedirect.com/science

Distribution of K, Na, Th and U in sandstones and shales from western Shikoku, Japan

International Nuclear Information System (INIS)

Ishihara, Shunso; Sakamaki, Yukio; Mochizuki, Tsunekazu; Terashima, Shigeru; Endo, Yuji

1981-01-01

The regional variation of K, Na, Th and U distributions was studied on 58 sandstones, 81 shales and 3 green schists from the sedimentary terrains across western Shikoku. The geological structure of the studied district is explained. The regional characteristics of the sedimentary rocks are best demonstrated in the composition of the sandstones. The sandstones, in the source areas of which granitic and rhyolitic rocks exist and which have been deposited rapidly, were rich in K, whereas those derived mainly from mafic volcanic areas showed high Na content. The sandstones of the Shimanto Supergroup had the intermediate values, and K and K + Na contents became low in the south where the younger Upper Shimanto Group is exposed. Th and U in both sandstones and shales were highest in the Izumi Group, and generally low in the Shimanto Supergroup. The black shales of the Shimanto Supergroup did not show U-anomaly. In each group, highly matured rocks gave slightly higher Th/U ratio. Highly matured polycyclic sediments contained the least amount of radioactive elements. The radioactive anomaly due to the anomalous K contained in sericite, and that due to U in black shale were found in Chichibu and Sambosan belts. Similar anomaly was discovered in the foot wall of Mn deposits in the same zone. The possibility of anomalous U may be the least in the Shimanto Supergroup. (Kako, I.)

Permeability measuremens of brazilian Eucalyptus

Directory of Open Access Journals (Sweden)

Marcio Rogério da Silva

2010-09-01

Full Text Available The permeability of Brazilian Eucalyptus grandis and Eucalyptus citriodora wood was measured in a custom build gas analysis chamber in order to determine which species could be successfully treated with preservatives. Liquid permeability was tested using an emulsion of Neen oil and a control of distillated water. Air was used to test the gas phase permeability. For both Eucalyptus grandis and Eucalyptus citriodora, the longitudinal permeability of gas was shown to be about twice as great as the liquid phase permeability. No radial permeability was observed for either wood. The permeability of air and water through the sapwood of Eucalyptus grandis was greater than that through the sapwood of Eucalyptus citriodora. The permeability of neen oil preservative through the sapwood of Eucalyptus grandis was also greater than through the sapwood of E. Citradora, but the difference was not statistically significant. Scanning Electron Microscopy images showed that the distribution and obstruction in the vessels could be correlated with observed permeability properties. Irrespective of the causes of differences in permeability between the species, the fluid phase flux through the sapwood of both species was significant, indicating that both Eucalyptus grandis and Eucalyptus citriodora could be successfully treated with wood preservative.

Intestinal Permeability: The Basics

Directory of Open Access Journals (Sweden)

Ingvar Bjarnason

1995-01-01

Full Text Available The authors review some of the more fundamental principles underlying the noninvasive assessment of intestinal permeability in humans, the choice of test markers and their analyses, and the practical aspects of test dose composition and how these can be changed to allow the specific assessment of regional permeability changes and other intestinal functions. The implications of increased intestinal permeability in the pathogenesis of human disease is discussed in relation to findings in patients with Crohn’s disease. A common feature of increased intestinal permeability is the development of a low grade enteropathy, and while quantitatively similar changes may be found in Crohn’s disease these seem to predict relapse of disease. Moreover, factors associated with relapse of Crohn’s disease have in common an action to increase intestinal permeability. While increased intestinal permeability does not seem to be important in the etiology of Crohn’s disease it may be a central mechanism in the clinical relapse of disease.

Study of pressure drop, void fraction and relative permeabilities of two phase flow through porous media

International Nuclear Information System (INIS)

Chu, W.; Dhir, V.K.; Marshall, J.

1983-01-01

An experimental investigation of two phase flow through porous layers formed of non-heated glass particles (nominal diameter 1 to 6 mm) has been made. Particulate bed depths of 30 cm and 70 cm were used. The effect of particle size, particle size distribution and bed porosity on void fraction and pressure drop through a particulate bed formed in a cylindrical test section has been investigated. The superficial velocity of liquid (water) is varied from 1.83 to 18.3 mm/s while the superficial velocity of gas (air) is varied from 0 to 68.4 mm/s. These superficial velocities were chosen so that pressure drop and void fraction measurement could be made for the porous layer in fixed and fluidized states. A model based on drift flux approach has been developed for the void fraction. Using the two phase friction pressure drop data, the relative permeabilities of the two phases have been concluded with void fraction. The void fraction and two phase friction pressure gradient in beds composed of mixtures of spherical particles as well as sharps of different nominal sizes have also been examined. It is found that the models for single size particles are also applicable to mixtures of particles if a mean particle diameter for the mixture is defined

Endolithic algae of semi-desert sandstones: systematic, biogeographic and ecophysiologic investigations

International Nuclear Information System (INIS)

Bell, R.A.

1986-01-01

Investigations were conducted into the ecology of an unusual algal community in northern Arizona. These microorganisms are called endolithic algae because they occur beneath the surface of rocks. Eighteen taxa, including representatives of both eukaryotic and prokaryotic genera, were isolated from below the surface of eight sandstones in four semi-desert and cold temperate biomes of the Colorado Plateau. As the macroclimate of the area changes from cold temperature desert scrub to cold temperate forest the taxonomic composition of the endolithic algal communities shifts from domination by coccoid blue-green algae to domination by coccoid and sarcinoid green algae. The algal communities varied in generic composition, chlorophyll a content, and in their location within the different sandstones. Investigations into the microclimate of the endolithic algal zone in two adjacent but differently-colored sections (white and brown) of Coconino sandstone have demonstrated differences between the environment above the rock surface and that just beneath the surface. In seasonal samples of the Coconino sandstone, chlorophyll a content ranged from 50 to 100 mg x m -2 in the white rock and 8 to 45 mg x m -2 in the brown rock. Primary production (as measured by 14 CO 2 incorporation) displayed marked seasonal patterns that appear to be correlated to the environmental conditions within the rocks as opposed to those outside the rocks. The widespread distribution of certain algae in the endolithic habitats of the Colorado Plateau and their presence in rocks at quite distant locations suggests that the endolithic habitat may be utilized by algae whenever it provides more favorable conditions than the surrounding surfaces

The Collyhurst Sandstone as a secondary storage unit for CCS in the East Irish Sea Basin (UK)

Science.gov (United States)

Gamboa, D.; Williams, J. D. O.; Kirk, K.; Gent, C. M. A.; Bentham, M.; Schofield, D. I.

2016-12-01

Carbon Capture and Storage (CCS) is key technology for low-carbon energy and industry. The UK hosts a large CO2 storage potential offshore with an estimated capacity of 78 Gt. The East Irish Sea Basin (EISB) is the key area for CCS in the western UK, with a CO2 storage potential of 1.7 Gt in hydrocarbon fields and in saline aquifers within the Triassic Sherwood Sandstone Formation. However, this theoretical storage capacity does not consider the secondary storage potential in the lower Permian Collyhurst Sandstone Formation. 3D seismic data were used to characterise the Collyhurst Sandstone Formation in the EISB. On the southern basin domain, numerous fault-bound blocks limit the lateral continuity of the sandstone strata, while on the northern domain the sandstones are intersected by less faults. The caprock for the Collyhurst sandstones is variable. The Manchester Marls predominate in the south, transitioning to the St. Bees evaporites towards the north. The evaporites in the EISB cause overburden faults to terminate or detach along Upper Permian strata, limiting the deformation of the underlying reservoir units. Five main storage closures have been identified in the Permian strata. In the southern and central area these are predominantly fault bounded, occurring at depths over 1000m. Despite the higher Collyhurst sandstone thickness in the southern IESB, the dolomitic nature of the caprock constitutes a storage risk in this area. Closures in the northern area are deeper (around 2000-2500m) and wider, reaching areas of 34Km2, and are overlain by evaporitic caprocks. The larger Collyhurst closures to the north underlie large Triassic fields with high storage potential. The spatial overlap favours storage plans including secondary storage units in the EISB. The results of this work also expand the understanding of prospective areas for CO2 sequestration in the East Irish Sea Basin in locations where the primary Sherwood Sandstone Formation is either too shallow

Evaluation of consolidating and water repellent treatments applied to the miocene sandstone used in Tunisian Heritage Monuments

Directory of Open Access Journals (Sweden)

Zoghlami, K.

2005-03-01

Full Text Available Summary The research reported in the present paper focused on the behaviour of the Miocene sandstone used to build the Roman aqueduct at Zaghouan-Carthage and other Tunisian Heritage monuments, after application of water repellent and consolidating treatments as a preliminary to restoration. Commercial consolidants and water repellents were used in the experiments: two ethyl silicate consolidants, Tegovakon (TV and Keim-Silex OH (KSOH; two (siloxane water repellents, Tegosivin THE 328 (THE and Tegosivin HLJ00 (THE; and a dual (consolidate and water repellent action substance, Keim- Silex H (KSH (silicate acid ester base with siloxane. A mixed treatment consisting of successive coats of TV and THL (TVHL was also applied. These organosilicate consolidants and water repellents acted on the porous structure of the sandstone, reducing total porosity and water vapour permeability. The water repellent THE was found to affect these properties least, with a pore size distribution that resembled the distribution in the untreated sandstone most closely. Water repellents diminish water absorption and consolidants increase mechanical strength. The TV-THL mix, which yielded results similar to those obtained with water repellents alone, was unable to prevent the substantial scaling that occurs during (RILEM salt crystallisation-induced artificial ageing. The best results were found with the dual action consolidant! water repellent product (KSH, which improved the mechanical properties while affording protection from the decay caused by salts in artificial ageing trials. This substance was found to reduce water vapour permeability, however

Esta investigación se centra en la evaluación del comportamiento de la arenisca miocénica utilizada en el acueducto de Zaghouan-Cartago y otros monumentos del Patrimonio Monumental de Túnez tras la aplicación de tratamientos de hidrofugación y de consolidación. Para los tratamientos se han seleccionado productos

Remote sensing information acquisition of paleo-channel sandstone-type uranium deposit in Nuheting area

International Nuclear Information System (INIS)

Liu Jianjun

2000-01-01

The author briefly describes the genesis and ore-formation mechanism of paleo-channel sandstone-type uranium deposit in Nuheting area. Techniques such as remote sensing digital image data processing and data enhancement, as well as 3-dimension quantitative analysis of drill hole data are applied to extract information on metallogenic environment of paleo-channel sandstone-type uranium deposit and the distribution of paleo-channel

Temperature Effects on Stiffness Moduli of Reservoir Sandstone from the Deep North Sea

DEFF Research Database (Denmark)

Orlander, Tobias; Andreassen, Katrine Alling; Fabricius, Ida Lykke

We investigate effect of testing temperature on the dynamic frame stiffness of quartz-bearing North Sea sandstone from depths of 5 km. We show that at low stress levels, the rock frame stiffens with increasing temperature and we propose an explanation for the controlling mechanisms. While...... temperature. This is unfortunate and hence, we designed a testing program with the intension of separating and quantifying effects of temperature and stress, specifically for the sandstone material subject to this study....

Enhanced Coal Bed Methane Recovery and CO2 Sequestration in the Powder River Basin

Energy Technology Data Exchange (ETDEWEB)

Eric P. Robertson

2010-06-01

Unminable coal beds are potentially large storage reservoirs for the sequestration of anthropogenic CO2 and offer the benefit of enhanced methane production, which can offset some of the costs associated with CO2 sequestration. The objective of this report is to provide a final topical report on enhanced coal bed methane recovery and CO2 sequestration to the U.S. Department of Energy in fulfillment of a Big Sky Carbon Sequestration Partnership milestone. This report summarizes work done at Idaho National Laboratory in support of Phase II of the Big Sky Carbon Sequestration Partnership. Research that elucidates the interaction of CO2 and coal is discussed with work centering on the Powder River Basin of Wyoming and Montana. Sorption-induced strain, also referred to as coal swelling/shrinkage, was investigated. A new method of obtaining sorption-induced strain was developed that greatly decreases the time necessary for data collection and increases the reliability of the strain data. As coal permeability is a strong function of sorption-induced strain, common permeability models were used to fit measured permeability data, but were found inadequate. A new permeability model was developed that can be directly applied to coal permeability data obtained under laboratory stress conditions, which are different than field stress conditions. The coal permeability model can be used to obtain critical coal parameters that can be applied in field models. An economic feasibility study of CO2 sequestration in unminable coal seams in the Powder River Basin of Wyoming was done. Economic analyses of CO2 injection options are compared. Results show that injecting flue gas to recover methane from CBM fields is marginally economical; however, this method will not significantly contribute to the need to sequester large quantities of CO2. Separating CO2 from flue gas and injecting it into the unminable coal zones of the Powder River Basin seam is currently uneconomical, but can

The mineralogy and genesis of uranium in rhyolitic ignimbrites of Precambrian age from Duobblon, Sweden

International Nuclear Information System (INIS)

Smellie, J.A.T.

1982-01-01

The Duobblon rhyolitic ignimbrites, of middle Precambrian age are 60 m thick. They consist of at least three flows with varying degrees of welding and have undergone devitrification, producing lithophysal and spherulitic textures. They are overlain by thick fluviatile red-bed-type conglomerates and sandstones, which in turn are capped by terrestrial acid volcanics. Uranium enrichments of up to 3000 ppm U occur within two or three peneconcordant tabular horizons which are mostly lithophysae-bearing. Fission-track investigations of the ignimbrites and overlying conglomerates and sandstones, which supplement earlier mineralogical studies, show that U occurs as fine pitchblende disseminations; as complex uranotitanates associated with Fe-Ti-Mn oxides; and as coatings associated with matrix sericite. Small amounts of U are present in such primary accessory minerals as sphene, apatite, and zircon. It is suggested that oxidizing U-bearing solutions, generated partly during devitrification of the ignimbrites and partly from the overlying volcano-sedimentary pile, produced the U enrichments with later sulphide deposition, along the more permeable lithophysal horizons in the ignimbrites. (author)

Influence of fluvial sandstone architecture on geothermal energy production

NARCIS (Netherlands)

Willems, C.J.L.; Maghami Nick, Hamidreza M.; Weltje, G.J.; Donselaar, M.E.; Bruhn, D.F.

2015-01-01

Fluvial sandstone reservoirs composed of stacked meander belts are considered as potential geothermal resources in the Netherlands. Net-to-gross, orientation and stacking pattern of the channel belts is of major importance for the connectivity between the injection and production well in such

Experimental Study of Cement - Sandstone/Shale - Brine - CO2 Interactions.

Science.gov (United States)

Carroll, Susan A; McNab, Walt W; Torres, Sharon C

2011-11-11

Reactive-transport simulation is a tool that is being used to estimate long-term trapping of CO2, and wellbore and cap rock integrity for geologic CO2 storage. We reacted end member components of a heterolithic sandstone and shale unit that forms the upper section of the In Salah Gas Project carbon storage reservoir in Krechba, Algeria with supercritical CO2, brine, and with/without cement at reservoir conditions to develop experimentally constrained geochemical models for use in reactive transport simulations. We observe marked changes in solution composition when CO2 reacted with cement, sandstone, and shale components at reservoir conditions. The geochemical model for the reaction of sandstone and shale with CO2 and brine is a simple one in which albite, chlorite, illite and carbonate minerals partially dissolve and boehmite, smectite, and amorphous silica precipitate. The geochemical model for the wellbore environment is also fairly simple, in which alkaline cements and rock react with CO2-rich brines to form an Fe containing calcite, amorphous silica, smectite and boehmite or amorphous Al(OH)3. Our research shows that relatively simple geochemical models can describe the dominant reactions that are likely to occur when CO2 is stored in deep saline aquifers sealed with overlying shale cap rocks, as well as the dominant reactions for cement carbonation at the wellbore interface.

Nivelstein sandstone, weakly lithified pure silica sands from the Dutch-German border area, intermittently used in architecture for two millennia

Science.gov (United States)

Nijland, Timo G.; Wim Dubelaar, C.

2017-04-01

The current paper provides a concise overview of the geological setting of the Nivelstein sandstone in broad sense, its petrographic and physical characteristics, and its use as natural stone. Miocene pure silica sands occur around Heerlen in the southeastern part of the Dutch province of Limburg and Herzogenrath in adjacent Germany, as well as in the Belgian province of Limburg near Opgrimbie. In Dutch Limburg and in Germany are three large active exploitations, quarrying the sands for industrial purposes. On top of the unconsolidated sands in the Herzogenrath quarry, lithified banks of sandstone occur, known as Nivelstein (or more rarely Herzogenrath) sandstone. This sandstone has been used as dimension stone and ornamental stone since Roman times. In the 11th century the quarry was reopened and after a long period of disuse sandstone blocks were again quarried in the second half of the 19th century. The lithification of the Nivelstein sandstone usually is very weak, with grain to grain contacts and some newly formed quartz rims only. The clay content is extremely low and is restricted to tiny booklets of kaolinite. Despite the weak cementation the Nivelstein sandstone has proved to be very time-resistant building stone that forms a major element in the stone cultural heritage of the Dutch- German border area.

provenance of sandstone on the western flank of anambra basin

African Journals Online (AJOL)

HP

GLOBAL JOURNAL OF GEOLOGICAL SCIENCES VOL. 14, 2016: 13-21. COPYRIGHT© ... from Fugar locality. The sandstones each classify as quartz arenites and sublitharenites. ... Tectonic movement in the Santonian times resulted in the ...

Discussion on several problems on the mineralization of paleo-channel sandstone type uranium deposits

International Nuclear Information System (INIS)

Huang Shijie

1997-01-01

On the basis of comprehensively analyzing paleo-channel sandstone type uranium deposits at home and abroad, the author discusses the division of mineralization types of paleo-channel sandstone type uranium deposits, and analyzes the metallogenic geologic conditions such as regional geologic background, climatic and geomorphological conditions, basement and sedimentary cover, characteristics of paleo-valley and paleo-channel, mineralization features as well as epigenetic metallogenic process. Future prospecting direction is also proposed

Clay minerals in sandstone uranium deposits: radwaste applications

International Nuclear Information System (INIS)

Brookins, D.G.

1990-01-01

Clay minerals play an important role in the genesis of uranium deposits in sandstones. They incorporate the rate earths (REE), U, Sb, Th, Cs, Rb, Sr, Y, Ba, and even small amounts of chalcophiles. These minerals possess analog elements for many of the radwaste fission products as well as actinides and some actinide daughters. In sandstone uranium deposits, clay minerals are also associated with sulfide minerals, usually pyrite, and organic carbonaceous matter. The primary clay minerals are usually smectites, illites, chlorites and mixed layer varieties. The integrity of these clay minerals is demonstrated by their retention of formational-mineralization ages determined by Rb-Sr geochronologic investigation of the Grants Mineral Belt of the United States. The importance of the clay minerals as analog for parts of the multi-barrier concept in radwaste disposal is their ability to impede water penetration into - and movement of key elements out of uranium rich zones. The clay minerals further sorb and in other ways incorporate into their structures many fission products and actinide analogs from man-made nuclear wastes. 22 refs., 1 fig., 3 tabs

Modelling of a diffusion-sorption experiment on sandstone

International Nuclear Information System (INIS)

Smith, P.A.

1989-11-01

The results of a diffusion-sorption experiment on a sample of Darley Dale sandstone, using simulated groundwater spiked with a mixture of 125 I, 85 Sr and 137 Cs, are modelled by a one-dimensional porous medium approach in which sorption is described by Freundlich isotherms. The governing equations are solved analytically for the special case of a linear isotherm, and numerically using the computer code RANCHDIFF for non-linear isotherms. A set of time-dependent, ordinary differential equations is obtained using the Lagrange interpolation technique and integrated by Gear's variable order predictor-corrector method. It is shown that the sorption behaviour of 85 Sr can be modelled successfully by a linear isotherm, using a sorption parameter consistent with batch-sorption tests. The behaviour of 137 Cs may be modelled by a non-linear isotherm, but the amount of 137 Cs sorbed is less than that anticipated from batch-sorption tests. 125 I is assumed to be non-sorbing and is used to determine the porosity of the sandstone. (author) 10 figs., 4 tabs., 6 refs

Metallogenic characteristics, model and exploration prospect for the paleo-interlayer-oxidation type sandstone-hosted uranium deposits in China

International Nuclear Information System (INIS)

Huang Jingbai; Li Shengxiang

2007-01-01

In this paper, the paleo-interlayer-oxidation type sandstone-hosted uranium deposits occurred in the Meso-Cenozoic continental basins in China are divided into 3 subtype, they are stratum over lapping buried subtype, structure-uplifting destroy subtype and faulted-folding conserved subtype. The metallogenic characteristics, metallogenic model and exploration prospect for these 3 subtypes uranium deposits are discussed. It is proposed that the paleo-interlayer-oxidation type sandstone-hosted uranium deposits, besides the recent interlayer oxidation type sandstone-hosted uranium deposits, are of great prospecting potential in the Meso-Cenozoic continental basins in China. Therefore, the metallogenic theory of these types uranium deposits should be conscientiously summarized and replenished continuously so as to propel forward the exploration of the sandstone-hosted uranium deposits in China. (authors)

Preliminary research on finite difference method to solve radon field distribution over sandstone-type uranium ore body

International Nuclear Information System (INIS)

Li Bihong; Shuang Na; Liu Qingcheng

2006-01-01

The principle of finite difference method is introduced, and the radon field distribution over sandstone-type uranium deposit is narrated. The radon field distribution theory equation is established. To solve radon field distribution equation using finite difference algorithm is to provide the value computational method for forward calculation about radon field over sandstone-type uranium mine. Study on 2-D finite difference method on the center of either high anomaly radon fields in view of the character of radon field over sandstone-type uranium provide an algorithm for further research. (authors)

CHARACTERIZATION OF SANDSTONE RESERVOIRS FOR ENHANCED OIL RECOVERY: THE PERMIAN UPPER MINNELUSA FORMATION, POWDER RIVER BASIN, WYOMING.

Science.gov (United States)

Schenk, C.J.; Schmoker, J.W.; Scheffler, J.M.

1986-01-01

Upper Minnelusa sandstones form a complex group of reservoirs because of variations in regional setting, sedimentology, and diagenetic alteration. Structural lineaments separate the reservoirs into northern and southern zones. Production in the north is from a single pay sand, and in the south from multi-pay sands due to differential erosion on top of the Upper Minnelusa. The intercalation of eolian dune, interdune, and sabkha sandstones with marine sandstones, carbonates, and anhydrites results in significant reservoir heterogeneity. Diagenetic alterations further enhance heterogeneity, because the degree of cementation and dissolution is partly facies-related.

Uranium-series disequilibria as a means to study recent migration of uranium in a sandstone-hosted uranium deposit, NW China

International Nuclear Information System (INIS)

Min Maozhong; Peng Xinjian; Wang Jinping; Osmond, J.K.

2005-01-01

Uranium concentration and alpha specific activities of uranium decay series nuclides 234 U, 238 U, 230 Th, 232 Th and 226 Ra were measured for 16 oxidized host sandstone samples, 36 oxic-anoxic (mineralized) sandstone samples and three unaltered primary sandstone samples collected from the Shihongtan deposit. The results show that most of the ores and host sandstones have close to secular equilibrium alpha activity ratios for 234 U/ 238 U, 230 Th/ 238 U, 230 Th/ 234 U and 226 Ra/ 230 Th, indicating that intensive groundwater-rock/ore interaction and uranium migration have not taken place in the deposit during the last 1.0 Ma. However, some of the old uranium ore bodies have locally undergone leaching in the oxidizing environment during the past 300 ka to 1.0 Ma or to the present, and a number of new U ore bodies have grown in the oxic-anoxic transition (mineralized) subzone during the past 1.0 Ma. Locally, uranium leaching has taken place during the past 300 ka to 1.0 Ma, and perhaps is still going on now in some sandstones of the oxidizing subzone. However, uranium accumulation has locally occurred in some sandstones of the oxidizing environment during the past 1 ka to 1.0 Ma, which may be attributed to adsorption of U(VI) by clays contained in oxidized sandstones. A recent accumulation of uranium has locally taken place within the unaltered sandstones of the primary subzone close to the oxic-anoxic transition environment during the past 300 ka to 1.0 Ma. Results from the present study also indicate that uranium-series disequilibrium is an important tool to trace recent migration of uranium occurring in sandstone-hosted U deposits during the past 1.0 Ma and to distinguish the oxidation-reduction boundary

Hydrogeology and geochemistry of low-permeability oil-shales - Case study from HaShfela sub-basin, Israel

Science.gov (United States)

Burg, Avihu; Gersman, Ronen

2016-09-01

Low permeability rocks are of great importance given their potential role in protecting underlying aquifers from surface and buried contaminants. Nevertheless, only limited data for these rocks is available. New appraisal wells drilled into the oil shale unit (OSU) of the Mt. Scopus Group in the HaShfela sub-basin, Central Israel, provided a one-time opportunity for detailed study of the hydrogeology and geochemistry of this very low permeability unit. Methods used include: slug tests, electrical logs, televiewer imaging, porosity and permeability measurements on core samples, chemical analyses of the rock column and groundwater analyses. Slug tests yielded primary indication to the low permeability of the OSU despite its high porosity (30-40%). Hydraulic conductivities as low as 10-10-10-12 m/s were calculated, using both the Hvorslev and Cooper-Bredehoeft-Papadopulos decoding methods. These low conductivities were confirmed by direct measurements of permeability in cores, and from calculations based on the Kozeny-Carman approach. Storativity was found to be 1 · 10-6 and specific storage - 3.8 · 10-9 m-1. Nevertheless, the very limited water flow in the OSU is argued to be driven gravitationally. The extremely slow recovery rates as well as the independent recovery of two adjacent wells, despite their initial large head difference of 214 m, indicate that the natural fractures are tight and are impermeable due to the confining stress at depth. Laboratory measured permeability is similar or even higher than the field-measured values, thereby confirming that fractures and bedding planes do not form continuous flow paths. The vertical permeability along the OSU is highly variable, implying hydraulic stratification and extremely low vertical hydraulic conductivity. The high salinity of the groundwater (6300-8000 mgCl/L) within the OSU and its chemical and isotopic compositions are explained by the limited water flow, suggesting long residence time of the water

Permeability of porour rhyolite

Science.gov (United States)

Cashman, K.; Rust, A.; Wright, H.; Roberge, J.

2003-04-01

The development of permeability in bubble-bearing magmas determines the efficiency of volatile escape during their ascent through volcanic conduits, which, in turn, controls their explosive potential. As permeability requires bubble connectivity, relationships between permeability and porosity in silicic magmas must be controlled by the formation, growth, deformation and coalescence of their constituent bubbles. Although permeability data on porous volcanic pyroclasts are limited, the database can be greatly extended by including data for ceramic and metallic foams1. Several studies indicate that a single number does not adequately describe the permeability of a foam because inertial effects, which predominate at high flow rates, cause deviations from Darcy's law. These studies suggest that permeability is best modeled using the Forschheimer equation to determine both the Darcy permeability (k1) and the non-Darcian (k2) permeability. Importantly, at the high porosities of ceramic foams (75-95%), both k1 and k2 are strongly dependent on pore size and geometry, suggesting that measurement of these parameters provides important information on foam structure. We determined both the connected porosity (by He-pycnometry) and the permeability (k1 and k2) of rhyolitic samples having a wide range in porosity (22-85%) and vesicle textures. In general, these data support previous observations of a power law relationship between connected porosity and Darcy permeability2. In detail, variations in k1 increase at higher porosities. Similarly, k2 generally increases in both mean and standard deviation with increasing porosity. Measurements made on three mutually perpendicular cores from individual pumice clasts suggest that some of the variability can be explained by anisotropy in the vesicle structure. By comparison with ceramic foams, we suggest that the remaining variability results from differences either in average vesicle size or, more likely, in the size of apertures

Prospect analysis for sandstone-type uranium mineralization in the northern margin of Qaidam basin

International Nuclear Information System (INIS)

Liu Lin; Song Xiansheng; Feng Wei; Song Zhe; Li Wei

2010-01-01

Affected by the regional geological structural evolution, a set of sedimentary structure, i.e. the construction of coal-bearing classic rocks which is in favor of the sandstone-type uranium mineralization has deposited in the northern margin of Qaidam Basin since Meso-Cenozoic. A NWW thrust nappe tectonic belt, i.e. the ancient tectonic belt which is the basis for the development of ancient interlayer oxidation zone formed by the tectonic reverse in late Jurassic and Cretaceous. The Mid and late Jurassic layer was buried by the weak extension in Paleogene and the depression in early Neogene. The extrusion reversal from late Neogene to Quaternary made the basin into the development era of the modern interlayer oxidation zone. It can be concluded that the layer of the northern margin of Qaidam Basin has the premise for the formation of sandstone-type uranium ore. Based on the analysis of the characteristics of the thrust belt, the structure of the purpose layer, the sand body, the hydrogeology, the interlayer oxidation zone and uranium mineralization, the results indicated that the ancient interlayer oxidation zone is the prospecting type of sandstone-type uranium ore. Beidatan and the east of Yuqia are the favorable prospective area of sandstone-type uranium mineralization. (authors)

The migration of uranium through sandstone

International Nuclear Information System (INIS)

Bennett, D.G.; Read, D.; Lawless, T.A.; Sims, R.J.

1992-01-01

Three column experiments are described in which the migration of uranium through Clashach Sandstone was studied. A priori predictions of uranium migration in the experiments were made using an equilibrium chemical transport model. The experimental results showed that, even under oxidising conditions, the migration of uranium is strongly retarded owing to the affinity of uranium for mineral surfaces. For the relatively simple chemical system investigated, the chemical transport model was successful in predicting the migration of uranium and its distribution along the column. (author)

Reviews on the metallogenic and geological features of sandstone-type uranium deposits in Japan

International Nuclear Information System (INIS)

Pei Chengkai; Huang Xianfang; Zhang Baoju

2006-01-01

Regional geologic settings of sandstone-type uranium deposits in Japan are firstly analyzed. The regional tectonic evolution characteristics of 'Green tuff region' and 'Non green tuff region' and their relationship with uranium mineralization are elaborated in depth. Based on those mentioned above, the uranium sources of sandstone-type uranium deposits in Japan are discussed deeply and the most favorable uranium sources are considered to come from the basement and the surrounding granites. Their intrusive epochs range from Later Cretaceous to Palaeogene (about 60 to 70 Ma ago). The characteristics of ore-bearing host rocks, matter compositions of the deposits, ore formation enrichment factors, the hydrogeologic conditions and so on are described by taking Ningyo-Toge and Tono deposits as examples. Finally, the prospecting measures for the palaeo-channel sandstone-type uranium deposits (basal type) are reviewed. (authors)

Two-dimensional lift-up problem for a rigid porous bed

Energy Technology Data Exchange (ETDEWEB)

Chang, Y.; Huang, L. H.; Yang, F. P. Y. [Department of Civil Engineering, National Taiwan University, Taipei, Taiwan (China)

2015-05-15

The present study analytically reinvestigates the two-dimensional lift-up problem for a rigid porous bed that was studied by Mei, Yeung, and Liu [“Lifting of a large object from a porous seabed,” J. Fluid Mech. 152, 203 (1985)]. Mei, Yeung, and Liu proposed a model that treats the bed as a rigid porous medium and performed relevant experiments. In their model, they assumed the gap flow comes from the periphery of the gap, and there is a shear layer in the porous medium; the flow in the gap is described by adhesion approximation [D. J. Acheson, Elementary Fluid Dynamics (Clarendon, Oxford, 1990), pp. 243-245.] and the pore flow by Darcy’s law, and the slip-flow condition proposed by Beavers and Joseph [“Boundary conditions at a naturally permeable wall,” J. Fluid Mech. 30, 197 (1967)] is applied to the bed interface. In this problem, however, the gap flow initially mainly comes from the porous bed, and the shear layer may not exist. Although later the shear effect becomes important, the empirical slip-flow condition might not physically respond to the shear effect, and the existence of the vertical velocity affects the situation so greatly that the slip-flow condition might not be appropriate. In contrast, the present study proposes a more general model for the problem, applying Stokes flow to the gap, the Brinkman equation to the porous medium, and Song and Huang’s [“Laminar poroelastic media flow,” J. Eng. Mech. 126, 358 (2000)] complete interfacial conditions to the bed interface. The exact solution to the problem is found and fits Mei’s experiments well. The breakout phenomenon is examined for different soil beds, mechanics that cannot be illustrated by Mei’s model are revealed, and the theoretical breakout times obtained using Mei’s model and our model are compared. The results show that the proposed model is more compatible with physics and provides results that are more precise.

THE SEDIMENTOLOGY OF THE LOWER PERMIAN DANDOT FORMATION: A COMPONENT OF THE GONDWANA DEGLACIATION SEQUENCE OF THE SALT RANGE, PAKISTAN

Directory of Open Access Journals (Sweden)

IRFAN U. JAN

2016-03-01

Full Text Available The Dandot Formation is a part of the Lower Permian, dominantly continental, Gondwanan Nilawahan Group in the Salt Range, Pakistan. The formation conformably overlies the glacio-fluvial Tobra Formation and has a sharp conformable contact with the overlying fluvio-continental Warchha Sandstone. Sedimentary analyses show that the Dandot Formation consists of: 1. bioturbated sandstone lithofacies (L1, 2. dark green mudstone/shale lithofacies (L2, 3. flaser bedded sandstone lithofacies (L3, 4. rippled sandstone lithofacies (L4, 5. cross-bedded sandstone lithofacies (L5, and 6. planar sandstone lithofacies (L6. These can be grouped into shoreface, inner shelf, and tidal flat and estuarine facies associations, deposited in shallow marine to intertidal environments. The upper part of the Tobra Formation at the Choa-Khewra road section, where it conformably underlies the Dandot Formation, contains palynomorphs assignable to the earliest Permian 2141B Biozone. In south Oman, the 2141B Biozone is closely associated with the Rahab Shale Member, a widespread shale unit which is considered to represent part of a Permian deglaciation sequence which culminates in the marine beds of the Lower Gharif Member, interpreted as due to post glacial marine transgression. Thus, the Tobra Formation and the overlying marine Dandot Formation may form part of a similar deglaciation sequence.

Intestinal permeability study of minoxidil: assessment of minoxidil as a high permeability reference drug for biopharmaceutics classification.

Science.gov (United States)

Ozawa, Makoto; Tsume, Yasuhiro; Zur, Moran; Dahan, Arik; Amidon, Gordon L

2015-01-05

The purpose of this study was to evaluate minoxidil as a high permeability reference drug for Biopharmaceutics Classification System (BCS). The permeability of minoxidil was determined in in situ intestinal perfusion studies in rodents and permeability studies across Caco-2 cell monolayers. The permeability of minoxidil was compared with that of metoprolol, an FDA reference drug for BCS classification. In rat perfusion studies, the permeability of minoxidil was somewhat higher than that of metoprolol in the jejunum, while minoxidil showed lower permeability than metoprolol in the ileum. The permeability of minoxidil was independent of intestinal segment, while the permeability of metoprolol was region-dependent. Similarly, in mouse perfusion study, the jejunal permeability of minoxidil was 2.5-fold higher than that of metoprolol. Minoxidil and metoprolol showed similar permeability in Caco-2 study at apical pH of 6.5 and basolateral pH of 7.4. The permeability of minoxidil was independent of pH, while metoprolol showed pH-dependent transport in Caco-2 study. Minoxidil exhibited similar permeability in the absorptive direction (AP-BL) in comparison with secretory direction (BL-AP), while metoprolol had higher efflux ratio (ER > 2) at apical pH of 6.5 and basolateral pH of 7.4. No concentration-dependent transport was observed for either minoxidil or metoprolol transport in Caco-2 study. Verapamil did not alter the transport of either compounds across Caco-2 cell monolayers. The permeability of minoxidil was independent of both pH and intestinal segment in intestinal perfusion studies and Caco-2 studies. Caco-2 studies also showed no involvement of carrier mediated transport in the absorption process of minoxidil. These results suggest that minoxidil may be an acceptable reference drug for BCS high permeability classification. However, minoxidil exhibited higher jejunal permeability than metoprolol and thus to use minoxidil as a reference drug would raise the

Interpretation of brine-permeability tests of the Salado Formation at the Waste Isolation Pilot Plant site: First interim report

International Nuclear Information System (INIS)

Beauheim, R.L.; Saulnier, G.J. Jr.; Avis, J.D.

1991-08-01

Pressure-pulse tests have been performed in bedded evaporites of the Salado Formation at the Waste Isolation Pilot Plant (WIPP) site to evaluate the hydraulic properties controlling brine flow through the Salado. Hydraulic conductivities ranging from about 10 -14 to 10 -11 m/s (permeabilities of about 10 -21 to 10 -18 m 2 ) have been interpreted from nine tests conducted on five stratigraphic intervals within eleven meters of the WIPP underground excavations. Tests of a pure halite layer showed no measurable permeability. Pore pressures in the stratigraphic intervals range from about 0.5 to 9.3 MPa. An anhydrite interbed (Marker Bed 139) appears to be one or more orders of magnitude more permeable than the surrounding halite. Hydraulic conductivities appear to increase, and pore pressures decrease, with increasing proximity to the excavations. These effects are particularly evident within two to three meters of the excavations. Two tests indicated the presence of apparent zero-flow boundaries about two to three meters from the boreholes. The other tests revealed no apparent boundaries within the radii of influence of the tests, which were calculated to range from about four to thirty-five meters from the test holes. The data are insufficient to determine if brine flow through evaporites results from Darcy-like flow driven by pressure gradients within naturally interconnected porosity or from shear deformation around excavations connecting previously isolated pores, thereby providing pathways for fluids at or near lithostatic pressure to be driven towards the low-pressure excavations. Future testing will be performed at greater distances from the excavations to evaluate hydraulic properties and processes beyond the range of excavation effects

Flow units classification for geostatisitical three-dimensional modeling of a non-marine sandstone reservoir: A case study from the Paleocene Funing Formation of the Gaoji Oilfield, east China

Science.gov (United States)

Zhang, Penghui; Zhang, Jinliang; Wang, Jinkai; Li, Ming; Liang, Jie; Wu, Yingli

2018-05-01

Flow units classification can be used in reservoir characterization. In addition, characterizing the reservoir interval into flow units is an effective way to simulate the reservoir. Paraflow units (PFUs), the second level of flow units, are used to estimate the spatial distribution of continental clastic reservoirs at the detailed reservoir description stage. In this study, we investigate a nonroutine methodology to predict the external and internal distribution of PFUs. The methodology outlined enables the classification of PFUs using sandstone core samples and log data. The relationships obtained between porosity, permeability and pore throat aperture radii (r35) values were established for core and log data obtained from 26 wells from the Funing Formation, Gaoji Oilfield, Subei Basin, China. The present study refines predicted PFUs at logged (0.125-m) intervals, whose scale is much smaller than routine methods. Meanwhile, three-dimensional models are built using sequential indicator simulation to characterize PFUs in wells. Four distinct PFUs are classified and located based on the statistical methodology of cluster analysis, and each PFU has different seepage ability. The results of this study demonstrate the obtained models are able to quantify reservoir heterogeneity. Due to different petrophysical characteristics and seepage ability, PFUs have a significant impact on the distribution of the remaining oil. Considering these allows a more accurate understanding of reservoir quality, especially within non-marine sandstone reservoirs.

Uranium minerals in Upper Carboniferous rocks in the Nowa Ruda region