Studies on Effective Elastic Properties of CNT/Nano-Clay Reinforced Polymer Hybrid Composite

Science.gov (United States)

Thakur, Arvind Kumar; Kumar, Puneet; Srinivas, J.

2016-02-01

This paper presents a computational approach to predict elastic propertiesof hybrid nanocomposite material prepared by adding nano-clayplatelets to conventional CNT-reinforced epoxy system. In comparison to polymers alone/single-fiber reinforced polymers, if an additional fiber is added to the composite structure, it was found a drastic improvement in resultant properties. In this regard, effective elastic moduli of a hybrid nano composite are determined by using finite element (FE) model with square representative volume element (RVE). Continuum mechanics based homogenization of the nano-filler reinforced composite is considered for evaluating the volumetric average of the stresses and the strains under different periodic boundary conditions.A three phase Halpin-Tsai approach is selected to obtain the analytical result based on micromechanical modeling. The effect of the volume fractions of CNTs and nano-clay platelets on the mechanical behavior is studied. Two different RVEs of nano-clay platelets were used to investigate the influence of nano-filler geometry on composite properties. The combination of high aspect ratio of CNTs and larger surface area of clay platelets contribute to the stiffening effect of the hybrid samples. Results of analysis are validated with Halpin-Tsai empirical formulae.

Identification of elastic properties of composite plate

International Nuclear Information System (INIS)

Kovalovs, A; Rucevskis, S

2011-01-01

Composite laminates are used extensively in the aerospace industry, especially for the fabrication of high-performance structures. The determination of stiffness parameters for complex materials, such as fibre-reinforced composites, is much more complicated than for isotropic materials. A conventional way is testing the coupon specimens, which are manufactured by technology similar to that used for the real, large structures. When such a method is used, the question arises of whether the material properties obtained from the coupon tests are the same as those in the large structure. Therefore, the determination of actual material properties for composite laminates using non-destructive evaluation techniques has been widely investigated. A number of various non-destructive evaluation techniques have been proposed for determining the material properties of composite laminates. In the present study, attention is focused on the identification of the elastic properties of laminated plate using vibration test data. The problem associated with vibration testing is converting the measured modal frequencies to elastic constants. A standard method for solving this problem is the use of a numerical-experimental model and optimization techniques. The identification functional represents the gap between the numerical model response and the experimental one. This gap should be minimized, taking into account the side constraints on the design variables (elastic constants). The minimization problem is solved by using non-linear mathematical programming techniques and sensitivity analysis. The results obtained were verified by comparing the experimentally measured eigenfrequencies with the numerical ones obtained by FEM at the point of optima

Flexural strength and modulus of elasticity of different types of resin-based composites.

Science.gov (United States)

Rodrigues Junior, Sinval Adalberto; Zanchi, Cesar Henrique; Carvalho, Rodrigo Varella de; Demarco, Flávio Fernando

2007-01-01

The aim of the study was to test whether the filler composition of resin composites influences their flexural strength and modulus of elasticity. Flexural strength and modulus of elasticity were obtained through a three-point bending test. Twelve bar shaped specimens of 5 commercially available composites--Supreme (3M/ESPE), a universal nanofilled composite; Esthet-X (Dentsply), Z-250 (3M/ESPE), Charisma (Heraeus Kulzer), universal hybrid composites; and Helio Fill (Vigodent), a microfine composite--were confectioned according to the ISO 4049/2000 specifications. The test was performed after a 7-days storage time using a universal test machine with a crosshead speed of 1 mm/min. The filler weight content was determined by the ashing technique. The data obtained on the mechanical properties were submitted to ANOVA and Tukey test (p elasticity results were observed among the universal hybrid composites. The nanofilled composite presented intermediary results. Within the limitations of this in vitro study, it could be concluded that the filler content significantly interfered in the flexural strength and modulus of elasticity of the composites tested.

Elastic-plastic deformation of fiber composites with a tetragonal structure

Energy Technology Data Exchange (ETDEWEB)

Makarova, E.IU.; Svistkova, L.A. (Permskii Politekhnicheskii Institut, Perm (USSR))

1991-02-01

Results of numerical solutions are presented for elastic-plastic problems concerning arbitrary loading of unidirectional composites in the transverse plane. The nucleation and evolution of microplastic zones in the matrix and the effect of this process on the macroscopic characteristics of the composite are discussed. Attention is also given to the effect of the fiber shape on the elastic-plastic deformation of the matrix and to deformation paths realized in simple microdeformation processes. The discussion is illustrated by results obtained for a composite consisting of a VT1-0 titanium alloy matrix reinforced by Ti-Mo fibers.

On the elastic properties of carbon nanotube-based composites: modelling and characterization

CERN Document Server

Thostenson, E T

2003-01-01

The exceptional mechanical and physical properties observed for carbon nanotubes has stimulated the development of nanotube-based composite materials, but critical challenges exist before we can exploit these extraordinary nanoscale properties in a macroscopic composite. At the nanoscale, the structure of the carbon nanotube strongly influences the overall properties of the composite. The focus of this research is to develop a fundamental understanding of the structure/size influence of carbon nanotubes on the elastic properties of nanotube-based composites. Towards this end, the nanoscale structure and elastic properties of a model composite system of aligned multi-walled carbon nanotubes embedded in a polystyrene matrix were characterized, and a micromechanical approach for modelling of short fibre composites was modified to account for the structure of the nanotube reinforcement to predict the elastic modulus of the nanocomposite as a function of the constituent properties, reinforcement geometry and nanot...

Elastic properties of rigid fiber-reinforced composites

Science.gov (United States)

Chen, J.; Thorpe, M. F.; Davis, L. C.

1995-05-01

We study the elastic properties of rigid fiber-reinforced composites with perfect bonding between fibers and matrix, and also with sliding boundary conditions. In the dilute region, there exists an exact analytical solution. Around the rigidity threshold we find the elastic moduli and Poisson's ratio by decomposing the deformation into a compression mode and a rotation mode. For perfect bonding, both modes are important, whereas only the compression mode is operative for sliding boundary conditions. We employ the digital-image-based method and a finite element analysis to perform computer simulations which confirm our analytical predictions.

Elastic Bands as a Component of Periodized Resistance Training.

Science.gov (United States)

Joy, Jordan M; Lowery, Ryan P; Oliveira de Souza, Eduardo; Wilson, Jacob M

2016-08-01

Joy, JM, Lowery, RP, Oliveira de Souza, E, and Wilson, JM. Elastic bands as a component of periodized resistance training. J Strength Cond Res 30(8): 2100-2106, 2016-Variable resistance training (VRT) has recently become a component of strength and conditioning programs. Prior research has demonstrated increases in power and/or strength using low loads of variable resistance. However, no study has examined using high loads of variable resistance as a part of a periodized training protocol to examine VRT within the context of a periodized training program and to examine a greater load of variable resistance than has been examined in prior research. Fourteen National Collegiate Athletic Association division II male basketball players were recruited for this study. Athletes were divided equally into either a variable resistance or control group. The variable resistance group added 30% of their 1 repetition maximum (1RM) as band tension to their prescribed weight 1 session per week. Rate of power development (RPD), peak power, strength, body composition, and vertical jump height were measured pretreatment and posttreatment. No baseline differences were observed between groups for any measurement of strength, power, or body composition. A significant group by time interaction was observed for RPD, in which RPD was greater in VRT posttraining than in the control group. Significant time effects were observed for all other variables including squat 1RM, bench press 1RM, deadlift 1RM, clean 3RM, vertical jump, and lean mass. Although there were no significant group ×-time interactions, the VRT group's percent changes and effect sizes indicate a larger treatment effect in the squat and bench press 1RM values and the vertical jump performed on the force plate and vertec. These results suggest that when using variable resistance as a component of a periodized training program, power and strength can be enhanced. Therefore, athletes who add variable resistance to 1 training

Air and ground resonance of helicopters with elastically tailored composite rotor blades

Science.gov (United States)

Smith, Edward C.; Chopra, Inderjit

1993-01-01

The aeromechanical stability, including air resonance in hover, air resonance in forward flight, and ground resonance, of a helicopter with elastically tailored composite rotor blades is investigated. Five soft-inplane hingeless rotor configurations, featuring elastic pitch-lag, pitch-flap and extension-torsion couplings, are analyzed. Elastic couplings introduced through tailored composite blade spars can have a powerful effect on both air and ground resonance behavior. Elastic pitch-flap couplings (positive and negative) strongly affect body, rotor and dynamic inflow modes. Air resonance stability is diminished by elastic pitch-flap couplings in hover and forwrad flight. Negative pitch-lag elastic coupling has a stabilizing effect on the regressive lag mode in hover and forward flight. The negative pitch-lag coupling has a detrimental effect on ground resonance stability. Extension-torsion elastic coupling (blade pitch decreases due to tension) decreases regressive lag mode stability in both airborne and ground contact conditions. Increasing thrust levels has a beneficial influence on ground resonance stability for rotors with pitch-flap and extension-torsion coupling and is only marginally effective in improving stability of rotors with pitch-lag coupling.

Postbuckling of magneto-electro-elastic CNT-MT composite nanotubes resting on a nonlinear elastic medium in a non-uniform thermal environment

Science.gov (United States)

Kamali, M.; Shamsi, M.; Saidi, A. R.

2018-03-01

As a first endeavor, the effect of nonlinear elastic foundation on the postbuckling behavior of smart magneto-electro-elastic (MEE) composite nanotubes is investigated. The composite nanotube is affected by a non-uniform thermal environment. A typical MEE composite nanotube consists of microtubules (MTs) and carbon nanotubes (CNTs) with a MEE cylindrical nanoshell for smart control. It is assumed that the nanoscale layers of the system are coupled by a polymer matrix or filament network depending on the application. In addition to thermal loads, magneto-electro-mechanical loads are applied to the composite nanostructure. Length scale effects are taken into account using the nonlocal elasticity theory. The principle of virtual work and von Karman's relations are used to derive the nonlinear governing differential equations of MEE CNT-MT nanotubes. Using Galerkin's method, nonlinear critical buckling loads are determined. Various types of non-uniform temperature distribution in the radial direction are considered. Finally, the effects of various parameters such as the nonlinear constant of elastic medium, thermal loading factor and small scale coefficient on the postbuckling of MEE CNT-MT nanotubes are studied.

The elastic modulus of alumina-zirconia composite using through transmission ultrasonics

International Nuclear Information System (INIS)

Tan, K.S.; Hing, P.

1996-01-01

The elastic modulus of unstabilized Al 2 O 3 -ZrO 2 composites is determined from ultrasonic velocities and density measurements. The dynamic elastic modulus and the density of the green unstabilized Al 2 O 3 -ZrO 2 follow the rule of mixture. However, the elastic modulus and density of the sintered Al 2 O 3 -ZrO 2 do not follow the rule of mixture. The elastic modulus and diametrical compressive fracture stress of the Al 2 O 3 can be enhanced by (1) a high green (before sintering) compacting pressure and (2) addition of about 3wt% unstabilized ZrO 2 at a sintering time of two hours at 1550 degC. The ZrO 2 is found to improve the bulk density of the composite by a reduction in the porosity. This improves the elastic modulus and the diametrical compressive fracture stress. The thermal expansion on cooling with > 25wt% ZrO 2 in the Al 2 O 3 matrix has also been established. (author)

Elastic Composite, Reinforced Lightweight Concrete as a Type of Resilient Composite Systems

OpenAIRE

Esmaeili, Kamyar

2015-01-01

. A kind of "Elastic Composite, Reinforced Lightweight Concrete (ECRLC)" with the mentioned specifics is a type of "Resilient Composite Systems (RCS)" in which, contrary to the basic geometrical assumption of flexure theory in Solid Mechanics, "the strain changes in the beam height during bending" is typically "Non-linear". . Through employing this integrated structure, with significant high strain capability and modulus of resilience in bending, we could constructively achieve high bearing c...

Initial magnetic susceptibility of the diluted magnetopolymer elastic composites

International Nuclear Information System (INIS)

Borin, D.Yu.; Odenbach, S.

2017-01-01

In this work diluted magnetopolymer elastic composites based on magnetic microparticles are experimentally studied. Considered samples have varied concentration of the magnetic powder and different structural anisotropy. Experimental data on magnetic properties are accomplished by microstructural observations performed using X-Ray tomography. Influence of the particles amount and structuring effects on the initial magnetic susceptibility of the composites as well as the applicability of the Maxwell-Garnett approximation, which is widely used in considerations of magnetopolymer elastic composites, are evaluated. It is demonstrated that the approximation works well for diluted samples containing randomly distributed magnetic particles and for the diluted samples with chain-like structures oriented perpendicular to an externally applied field, while it fails to predict the susceptibility of the samples with structures oriented parallel to the field. Moreover, it is shown, that variation of the chains morphology does not significantly change the composite initial magnetic susceptibility. - Highlights: • The Maxwell-Garnet prediction works well for the diluted isotropic composites. • The Maxwell-Garnet prediction can be used for composites with structures oriented perpendicular to an applied field. • Chains oriented parallel to an applied field significantly increase the composite initial magnetic susceptibility. • The number and thickness of chains is not of the highest importance for the diluted composites. • The crucial reason of the observed effect is expected to be the demagnetisation factor of the chains.

Mathematical model predicts the elastic behavior of composite materials

Directory of Open Access Journals (Sweden)

Zoroastro de Miranda Boari

2005-03-01

Full Text Available Several studies have found that the non-uniform distribution of reinforcing elements in a composite material can markedly influence its characteristics of elastic and plastic deformation and that a composite's overall response is influenced by the physical and geometrical properties of its reinforcing phases. The finite element method, Eshelby's method and dislocation mechanisms are usually employed in formulating a composite's constitutive response. This paper discusses a composite material containing SiC particles in an aluminum matrix. The purpose of this study was to find the correlation between a composite material's particle distribution and its resistance, and to come up with a mathematical model to predict the material's elastic behavior. The proposed formulation was applied to establish the thermal stress field in the aluminum-SiC composite resulting from its fabrication process, whereby the mixture is prepared at 600 °C and the composite material is used at room temperature. The analytical results, which are presented as stress probabilities, were obtained from the mathematical model proposed herein. These results were compared with the numerical ones obtained by the FEM method. A comparison of the results of the two methods, analytical and numerical, reveals very similar average thermal stress values. It is also shown that Maxwell-Boltzmann's distribution law can be applied to identify the correlation between the material's particle distribution and its resistance, using Eshelby's thermal stresses.

Ultrasonic Determination of the Elastic Constants of Epoxy-natural Fiber Composites

Science.gov (United States)

Valencia, C. A. Meza; Pazos-Ospina, J. F.; Franco, E. E.; Ealo, Joao L.; Collazos-Burbano, D. A.; Garcia, G. F. Casanova

This paper shows the applications ultrasonic through-transmission technique to determine the elastic constants of two polymer-natural fiber composite materials with potential industrial application and economic and environmental advantages. The transversely isotropic coconut-epoxy and fique-epoxy samples were analyzed using an experimental setup which allows the sample to be rotated with respect to transducers faces and measures the time-of-flight at different angles of incidence. Then, the elastic properties of the material were obtained by fitting the experimental data to the Christoffel equation. Results show a good agreement between the measured elastic constants and the values predicted by an analytical model. The velocities as a function of the incidence angle are reported and the effect of the natural fiber on the stiffness of the composite is discussed.

Experimental investigation of flow field around the elastic flag flapping in periodic state

Science.gov (United States)

Jia, Yongxia; Jia, Lichao; Su, Zhuang; Yuan, Huijing

2018-05-01

The flapping of a flag in the wind is a classical fluid-structure problem that concerns the interaction of elastic bodies with ambient fluid. We focus on the desirable experimental results of the flow around the flapping flag. By immersing the elastic yet self-supporting heavy flag into water flow, we use particle image velocimetry (PIV) techniques to obtain the whole flow field around the midspan of the flag interacting with a fluid in periodic state. A unique PIV image processing method is used to measure near-wall flow velocities around a moving elastic flag. There exists a thin flow circulation region on the suction side of the flag in periodic state. This observation suggests that viscous flow models may be needed to improve the theoretical predictions of the flapping flag in periodic state, especially in a large amplitude.

The effect of inclusions on macroscopic composite elasticity: A systematic finite-element analysis of constituent and bulk elastic properties

International Nuclear Information System (INIS)

Yoneda, A; Sohag, F H

2010-01-01

The bulk physical properties of composite systems are difficult to predict - even when the properties of the constituent materials in the system are well known. We conducted a finite-element method simulation to examine the inclusion effect by substituting an inclusion phase (second phase) into a host phase (first phase). We have organized the simulation results as a function of the elasticity of host and inclusion phases. In this procedure, special attention was paid to the initial change of elastic constants as the inclusion volume ratio was varied. To accomplish this, we introduced a new parameter D ij defined as the derivatives of the normalized stiffness elastic constant over the inclusion volume ratio. We succeeded in obtaining useful systematic formulations for D ij . These formulations are expected to be applicable to the study of composite systems in many disciplines, such as geophysics, mechanics, material engineering, and biology. The present results provide much more effective constraints on the physical properties of composite systems, like rocks, than traditional methods, such as the Voigt-Reuss bounds.

Marginal elasticity of periodic triangulated origami

Science.gov (United States)

Chen, Bryan; Sussman, Dan; Lubensky, Tom; Santangelo, Chris

Origami, the classical art of folding paper, has inspired much recent work on assembling complex 3D structures from planar sheets. Origami, and more generally hinged structures with rigid panels, where all faces are triangles have special properties due to having a bulk balance of mechanical degrees of freedom and constraints. We study two families of periodic triangulated origami structures, one based on the Miura ori and one based on a kagome-like pattern due to Ron Resch. We point out the consequences of the balance of degrees of freedom and constraints for these ''metamaterial plates'' and show how the elasticity can be tuned by changing the unit cell geometry.

Optimal determination of the elastic constants of woven 2D SiC/SiC composite materials

International Nuclear Information System (INIS)

Mouchtachi, A; Guerjouma, R El; Baboux, J C; Rouby, D; Bouami, D

2004-01-01

For homogeneous materials, the ultrasonic immersion method, associated with a numerical optimization process mostly based on Newton's algorithm, allows the determination of elastic constants for various synthetic and natural composite materials. Nevertheless, a principal limitation of the existing optimization procedure occurs when the considered material is at the limit of the homogeneous hypothesis. Such is the case of the woven bidirectional SiC matrix and SiC fibre composite material. In this study, we have developed two numerical methods for the determination of the elastic constants of the 2D SiC/SiC composite material (2D SiC/SiC). The first one is based on Newton's algorithm: the elastic constants are obtained by minimizing the square deviation between experimental and calculated velocities. The second method is based on the Levenberg-Marquardt algorithm. We show that these algorithms give the same results in the case of homogeneous anisotropic composite materials. For the 2D SiC/SiC composite material, the two methods, using the same measured velocities, give different sets of elastic constants. We then note that the Levenberg-Marquardt algorithm enables a better convergence towards a global set of elastic constants in good agreement with the elastic properties, which can be measured using classical quasi-static methods

Elastic torsional buckling of thin-walled composite cylinders

Science.gov (United States)

Marlowe, D. E.; Sushinsky, G. F.; Dexter, H. B.

1974-01-01

The elastic torsional buckling strength has been determined experimentally for thin-walled cylinders fabricated with glass/epoxy, boron/epoxy, and graphite/epoxy composite materials and composite-reinforced aluminum and titanium. Cylinders have been tested with several unidirectional-ply orientations and several cross-ply layups. Specimens were designed with diameter-to-thickness ratios of approximately 150 and 300 and in two lengths of 10 in. and 20 in. The results of these tests were compared with the buckling strengths predicted by the torsional buckling analysis of Chao.

Second-order two-scale method for bending behaviors of composite plate with periodic configuration

International Nuclear Information System (INIS)

Zhu Guoqing; Cui Junzhi

2010-01-01

In this paper, the second-order two-scale analysis method for bending behaviors of the plate made from composites with 3-D periodic configuration is presented by means of construction way. It can capture the microscopic 3-D mechanics behaviors caused from 3-D micro-structures. First, directly starting from the 3-D elastic plate model of composite materials with 3-D periodic configuration, three cell models are defined, and correspondingly the three classes of cell functions only defined on 3 normalized cells are constructed. And then, the effective homogenization parameters of composites are calculated from those local functions, it leads to a 2-D homogenized laminar plate problem. Next, to solve it the homogenization solution is obtained. Finally, the second-order two-scale solution is constructed from the micro-cell functions and the homogenization solution.

Analysis, design and elastic tailoring of composite rotor blades

Science.gov (United States)

Rehfield, Lawrence W.; Atilgan, Ali R.

1987-01-01

The development of structural models for composite rotor blades is summarized. The models are intended for use in design analysis for the purpose of exploring the potential of elastic tailoring. The research was performed at the Center for Rotary Wing Aircraft Technology.

Nonlinear electroelastic deformations of dielectric elastomer composites: II - Non-Gaussian elastic dielectrics

Science.gov (United States)

Lefèvre, Victor; Lopez-Pamies, Oscar

2017-02-01

This paper presents an analytical framework to construct approximate homogenization solutions for the macroscopic elastic dielectric response - under finite deformations and finite electric fields - of dielectric elastomer composites with two-phase isotropic particulate microstructures. The central idea consists in employing the homogenization solution derived in Part I of this work for ideal elastic dielectric composites within the context of a nonlinear comparison medium method - this is derived as an extension of the comparison medium method of Lopez-Pamies et al. (2013) in nonlinear elastostatics to the coupled realm of nonlinear electroelastostatics - to generate in turn a corresponding solution for composite materials with non-ideal elastic dielectric constituents. Complementary to this analytical framework, a hybrid finite-element formulation to construct homogenization solutions numerically (in three dimensions) is also presented. The proposed analytical framework is utilized to work out a general approximate homogenization solution for non-Gaussian dielectric elastomers filled with nonlinear elastic dielectric particles that may exhibit polarization saturation. The solution applies to arbitrary (non-percolative) isotropic distributions of filler particles. By construction, it is exact in the limit of small deformations and moderate electric fields. For finite deformations and finite electric fields, its accuracy is demonstrated by means of direct comparisons with finite-element solutions. Aimed at gaining physical insight into the extreme enhancement in electrostriction properties displayed by emerging dielectric elastomer composites, various cases wherein the filler particles are of poly- and mono-disperse sizes and exhibit different types of elastic dielectric behavior are discussed in detail. Contrary to an initial conjecture in the literature, it is found (inter alia) that the isotropic addition of a small volume fraction of stiff (semi

Algorithm of constructing hybrid effective modules for elastic isotropic composites

Science.gov (United States)

Svetashkov, A. A.; Miciński, J.; Kupriyanov, N. A.; Barashkov, V. N.; Lushnikov, A. V.

2017-02-01

The algorithm of constructing of new effective elastic characteristics of two-component composites based on the superposition of the models of Reiss and Voigt, Hashin and Strikman, as well as models of the geometric average for effective modules. These effective characteristics are inside forks Voigt and Reiss. Additionally, the calculations of the stress-strain state of composite structures with new effective characteristics give more accurate prediction than classical models do.

Elastic waves at periodically-structured surfaces and interfaces of solids

Directory of Open Access Journals (Sweden)

A. G. Every

2014-12-01

Full Text Available This paper presents a simple treatment of elastic wave scattering at periodically structured surfaces and interfaces of solids, and the existence and nature of surface acoustic waves (SAW and interfacial (IW waves at such structures. Our treatment is embodied in phenomenological models in which the periodicity resides in the boundary conditions. These yield zone folding and band gaps at the boundary of, and within the Brillouin zone. Above the transverse bulk wave threshold, there occur leaky or pseudo-SAW and pseudo-IW, which are attenuated via radiation into the bulk wave continuum. These have a pronounced effect on the transmission and reflection of bulk waves. We provide examples of pseudo-SAW and pseudo-IW for which the coupling to the bulk wave continuum vanishes at isloated points in the dispersion relation. These supersonic guided waves correspond to embedded discrete eigenvalues within a radiation continuum. We stress the generality of the phenomena that are exhibited at widely different scales of length and frequency, and their relevance to situations as diverse as the guiding of seismic waves in mine stopes, the metrology of periodic metal interconnect structures in the semiconductor industry, and elastic wave scattering by an array of coplanar cracks in a solid.

Elastic-plastic analysis of AS4/PEEK composite laminate using a one-parameter plasticity model

Science.gov (United States)

Sun, C. T.; Yoon, K. J.

1992-01-01

A one-parameter plasticity model was shown to adequately describe the plastic deformation of AS4/PEEK (APC-2) unidirectional thermoplastic composite. This model was verified further for unidirectional and laminated composite panels with and without a hole. The elastic-plastic stress-strain relations of coupon specimens were measured and compared with those predicted by the finite element analysis using the one-parameter plasticity model. The results show that the one-parameter plasticity model is suitable for the analysis of elastic-plastic deformation of AS4/PEEK composite laminates.

Elastic stiffnesses of an Nb-Ti/Cu-composite superconductive wire

Science.gov (United States)

Kim, Sudook; Ledbetter, Hassel; Ogi, Hirotsugu

2000-09-01

Elastic-stiffness coefficients were determined on a 1.4-mm-diameter wire consisting of superconducting Nb-Ti fibers in a copper matrix, with a polyvinyl-resin coating. The matrix contained 324 Nb-Ti fibers. An electromagnetic-acoustic-resonance method was used to obtain five independent elastic-stiffness coefficients assuming transverse-isotropic symmetry. From these we calculated Young moduli, bulk modulus, and principal Poisson ratios. As a check, we used a mechanical-impulse-excitation method to directly measure the Young modulus in the fiber direction. The three-phase composite wire showed a 10% anisotropy in the Young modulus.

Optimizing Thermal-Elastic Properties of C/C–SiC Composites Using a Hybrid Approach and PSO Algorithm

Science.gov (United States)

Xu, Yingjie; Gao, Tian

2016-01-01

Carbon fiber-reinforced multi-layered pyrocarbon–silicon carbide matrix (C/C–SiC) composites are widely used in aerospace structures. The complicated spatial architecture and material heterogeneity of C/C–SiC composites constitute the challenge for tailoring their properties. Thus, discovering the intrinsic relations between the properties and the microstructures and sequentially optimizing the microstructures to obtain composites with the best performances becomes the key for practical applications. The objective of this work is to optimize the thermal-elastic properties of unidirectional C/C–SiC composites by controlling the multi-layered matrix thicknesses. A hybrid approach based on micromechanical modeling and back propagation (BP) neural network is proposed to predict the thermal-elastic properties of composites. Then, a particle swarm optimization (PSO) algorithm is interfaced with this hybrid model to achieve the optimal design for minimizing the coefficient of thermal expansion (CTE) of composites with the constraint of elastic modulus. Numerical examples demonstrate the effectiveness of the proposed hybrid model and optimization method. PMID:28773343

Hydro-elastic analysis and optimization of a composite marine propeller

DEFF Research Database (Denmark)

Blasques, José Pedro Albergaria Amaral; Berggreen, Christian; Andersen, Poul

2010-01-01

The present paper addresses the design and optimization of a flexible composite marine propeller. The aim is to tailor the laminate to control the deformed shape of the blade and consequently the developed thrust. The development of a hydro-elastic model is presented, and the laminate lay-up which...

Hydro-Elastic Tailoring and Optimization of a Composite Marine Propeller

DEFF Research Database (Denmark)

Blasques, José Pedro Albergaria Amaral; Berggreen, Christian; Andersen, Poul

2008-01-01

The following paper deals with the design and optimization of a flexible composite marine propeller. The blade shape is obtained from an existing high skew metal propeller. The aim is to tailor the laminate to control the elastic couplings and therefore the deformed shape of the blade. The develo...

Evaluation of linear polymerization shrinkage, flexural strength and modulus of elasticity of dental composites

Directory of Open Access Journals (Sweden)

Gabriela Queiroz de Melo Monteiro

2010-03-01

Full Text Available Linear polymerization shrinkage (LPS, flexural strength (FS and modulus of elasticity (ME of 7 dental composites (Filtek Z350™, Filtek Z250™/3M ESPE; Grandio™, Polofil Supra™/VOCO; TPH Spectrum™, TPH3™, Esthet-X™/Denstply were measured. For the measurement of LPS, composites were applied to a cylindrical metallic mold and polymerized (n = 8. The gap formed at the resin/mold interface was observed using scanning electron microscopy (1500×. For FS and ME, specimens were prepared according to the ISO 4049 specifications (n = 10. Statistical analysis of the data was performed with one-way ANOVA and the Tukey test. TPH Spectrum presented significantly higher LPS values (29.45 µm. Grandio had significantly higher mean values for FS (141.07 MPa and ME (13.91 GPa. The relationship between modulus of elasticity and polymerization shrinkage is the main challenge for maintenance of the adhesive interface, thus composites presenting high shrinkage values, associated with a high modulus of elasticity tend to disrupt the adhesive interface under polymerization.

Elastic properties

International Nuclear Information System (INIS)

Ledbetter, H.M.

1983-01-01

This chapter investigates the following five aspects of engineering-material solid-state elastic constants: general properties, interrelationships, relationships to other physical properties, changes during cooling from ambient to near-zero temperature, and near-zero-temperature behavior. Topics considered include compressibility, bulk modulus, Young's modulus, shear modulus, Poisson's ratio, Hooke's law, elastic-constant measuring methods, thermodynamic potentials, higher-order energy terms, specific heat, thermal expansivity, magnetic materials, structural phase transitions, polymers, composites, textured aggregates, and other-phenomena correlations. Some of the conclusions concerning polycrystalline elastic properties and their temperature dependence are: elastic constants are physical, not mechanical, properties which relate thermodynamically to other physical properties such as specific heat and thermal expansivity; elastic constants at low temperatures are nearly temperature independent, as required by the third law of thermodynamics; and elastic constants can be used to study directional properties of materials, such as textured aggregates and composites

Lamb Production Costs: Analyses of Composition and Elasticities Analysis of Lamb Production Costs

Directory of Open Access Journals (Sweden)

C. Raineri

2015-08-01

Full Text Available Since lamb is a commodity, producers cannot control the price of the product they sell. Therefore, managing production costs is a necessity. We explored the study of elasticities as a tool for basing decision-making in sheep production, and aimed at investigating the composition and elasticities of lamb production costs, and their influence on the performance of the activity. A representative sheep production farm, designed in a panel meeting, was the base for calculation of lamb production cost. We then performed studies of: i costs composition, and ii cost elasticities for prices of inputs and for zootechnical indicators. Variable costs represented 64.15% of total cost, while 21.66% were represented by operational fixed costs, and 14.19% by the income of the factors. As for elasticities to input prices, the opportunity cost of land was the item to which production cost was more sensitive: a 1% increase in its price would cause a 0.2666% increase in lamb cost. Meanwhile, the impact of increasing any technical indicator was significantly higher than the impact of rising input prices. A 1% increase in weight at slaughter, for example, would reduce total cost in 0.91%. The greatest obstacle to economic viability of sheep production under the observed conditions is low technical efficiency. Increased production costs are more related to deficient zootechnical indexes than to high expenses.

Guided elastic waves produced by a periodically joined interface in a rock mass

CSIR Research Space (South Africa)

Yenwong Fai

2012-09-01

Full Text Available on Computational and Applied Mechanics SACAM2012 Johannesburg, South Africa, 3−5 September 2012 c©SACAM Guided Elastic Waves Produced by a Periodically Joined Interface in a Rock Mass A.S. Yenwong Fai School of Physics University of the Witwatersrand Johannesburg...

Elasticity in Elastics-An in-vitro study.

Science.gov (United States)

Kamisetty, Supradeep Kumar; Nimagadda, Chakrapani; Begam, Madhoom Ponnachi; Nalamotu, Raghuveer; Srivastav, Trilok; Gs, Shwetha

2014-04-01

Orthodontic tooth movement results from application of forces to teeth. Elastics in orthodontics have been used both intra-orally and extra- orally to a great effect. Their use, combined with good patient co-operation provides the clinician with the ability to correct both anteroposterior and vertical discrepancies. Force decay over a period of time is a major problem in the clinical usage of latex elastics and synthetic elastomers. This loss of force makes it difficult for the clinician to determine the actual force transmitted to the dentition. It's the intent of the clinician to maintain optimal force values over desired period of time. The majority of the orthodontic elastics on the market are latex elastics. Since the early 1990s, synthetic products have been offered in the market for latex-sensitive patients and are sold as nonlatex elastics. There is limited information on the risk that latex elastics may pose to patients. Some have estimated that 0.12-6% of the general population and 6.2% of dental professionals have hypersensitivity to latex protein. There are some reported cases of adverse reactions to latex in the orthodontic population but these are very limited to date. Although the risk is not yet clear, it would still be inadvisable to prescribe latex elastics to a patient with a known latex allergy. To compare the in-vitro performance of latex and non latex elastics. Samples of 0.25 inch, latex and non latex elastics (light, medium, heavy elastics) were obtained from three manufacturers (Forestadent, GAC, Glenroe) and a sample size of ten elastics per group was tested. The properties tested included cross sectional area, internal diameter, initial force generated by the elastics, breaking force and the force relaxation for the different types of elastics. Force relaxation testing involved stretching the elastics to three times marketed internal diameter (19.05 mm) and measuring force level at intervals over a period of 48 hours. The data were

Stability of elastic columns with periodic retarded follower forces

Science.gov (United States)

Ma, Haitao; Butcher, Eric A.

2005-09-01

The objective of this work is to present a stability analysis for elastic columns under the influence of periodically varying follower forces whose orientation is retarded, i.e., depends on the position of the system at a previous time. One- and two-degree-of-freedom (dof) discretized systems under the simultaneous influence of both parametric excitation and time-delay, whose effects on such systems have previously been only considered separately, are studied. By employing an orthogonal polynomial approximation, the infinite-dimensional Floquet transition matrix associated with the time-periodic differential-delay system is approximated. The stability criteria that all the eigenvalues (Floquet multipliers) of this matrix must lie within the unit circle is then applied. The stability charts for different combinations of the remaining system parameters are shown, and the previously reported results for the special cases where either the parametric excitation or the time-delay vanishes are verified. Two cases, when the parametric forcing period is equal to or twice the delay period are taken into consideration in this work. For special cases of the single dof system, the numerical stability plots are verified by considering the analytical expressions for the corresponding stability boundaries for an analogous delayed Mathieu equation.

A Unit-Cell Model for Predicting the Elastic Constants of 3D Four Directional Cylindrical Braided Composite Shafts

Science.gov (United States)

Hao, Wenfeng; Liu, Ye; Huang, Xinrong; Liu, Yinghua; Zhu, Jianguo

2018-06-01

In this work, the elastic constants of 3D four directional cylindrical braided composite shafts were predicted using analytical and numerical methods. First, the motion rule of yarn carrier of 3D four directional cylindrical braided composite shafts was analyzed, and the horizontal projection of yarn motion trajectory was obtained. Then, the geometry models of unit-cells with different braiding angles and fiber volume contents were built up, and the meso-scale models of 3D cylindrical braided composite shafts were obtained. Finally, the effects of braiding angles and fiber volume contents on the elastic constants of 3D braided composite shafts were analyzed theoretically and numerically. These results play a crucial role in investigating the mechanical properties of 3D 4-directional braided composites shafts.

Elastic modulus of Al-Si/SiC metal matrix composites as a function of volume fraction

Energy Technology Data Exchange (ETDEWEB)

Santhosh Kumar, S; Rajasekharan, T [Powder Metallurgy Group, Defence Metallurgical Research Laboratory, Kanchanbagh PO, Hyderabad-500 058 (India); Seshu Bai, V [School of Physics, University of Hyderabad, Central University PO, Hyderabad-500 046 (India); Rajkumar, K V; Sharma, G K; Jayakumar, T, E-mail: dearsanthosh@gmail.co [Non-Destructive Evaluation Division, Indira Gandhi Center for Atomic Research, Kalpakkam, Chennai-603 102 (India)

2009-09-07

Aluminum alloy matrix composites have emerged as candidate materials for electronic packaging applications in the field of aerospace semiconductor electronics. Composites prepared by the pressureless infiltration technique with high volume fractions in the range 0.41-0.70 were studied using ultrasonic velocity measurements. For different volume fractions of SiC, the longitudinal velocity and shear velocity were found to be in the range of 7600-9300 m s{sup -1} and 4400-5500 m s{sup -1}, respectively. The elastic moduli of the composites were determined from ultrasonic velocities and were analysed as a function of the volume fraction of the reinforcement. The observed variation is discussed in the context of existing theoretical models for the effective elastic moduli of two-phase systems.

Effects of microstructure on the elastic properties of selected Ta2O5--Eu2O3 compositions

International Nuclear Information System (INIS)

Malarkey, C.J.

1977-06-01

Elastic properties and internal friction of selected compositions of tantala-doped monoclinic europia were studied at temperatures up to 1500 0 C using the sonic resonance technique. Unit cell parameters between 25C and 1000 0 C for monoclinic Eu 2 O 3 were calculated from high temperature x-ray diffractometer data. Large-grained monoclinic specimens having less than 6.0 Ta cation percent substitution exhibited anomalous elastic behavior when thermally cycled. Compositions above this addition level exhibited linear elastic behavior. Internal friction values also varied abnormally with grain size, composition, and temperature. The anomalous behavior was attributed to microcracking caused by thermal expansion anisotropies. The critical grain size was found to be approximately 14 μm. The high temperature diffractometry measurements supported the postulate that the grain coarsening effect associated with sintered monoclinic Eu 2 O 3 is the controlling factor for microcracking

Elastic Moduli of Nanoparticle-Polymer Composite Thin Films via Buckling on Elastomeric Substrates

Science.gov (United States)

Yuan, Hongyi; Karim, Alamgir; University of Akron Team

2011-03-01

Polymeric thin films find applications in diverse areas such as coatings, barriers and packaging. The dispersion of nanoparticles into the films was proven to be an effective method to generate tunable properties, particularly mechanical strength. However, there are very few methods for mechanical characterization of the composite thin films with high accuracy. In this study, nanometric polystyrene and polyvinyl alcohol films with uniformly dispersed cobalt and Cloisite nanoparticles at varying concentrations were synthesized via flow-coating and then transferred to crosslinked polydimethylsiloxane (PDMS) flexible substrates. The technique of Strain-Induced Elastic Buckling Instability for Mechanical Measurements (SIEBIMM) was employed to determine the elastic moduli of the films, which were calculated from the buckling patterns generated by applying compressive stresses. Results on moduli of films as a function of the concentrations of nanoparticles and the thicknesses of the composite films will be presented. *Corresponding author: alamgir@uakron.edu

On the Effect of Unit-Cell Parameters in Predicting the Elastic Response of Wood-Plastic Composites

Directory of Open Access Journals (Sweden)

Fatemeh Alavi

2013-01-01

Full Text Available This paper presents a study on the effect of unit-cell geometrical parameters in predicting elastic properties of a typical wood plastic composite (WPC. The ultimate goal was obtaining the optimal values of representative volume element (RVE parameters to accurately predict the mechanical behavior of the WPC. For each unit cell, defined by a given combination of the above geometrical parameters, finite element simulation in ABAQUS was carried out, and the corresponding stress-strain curve was obtained. A uniaxial test according to ASTM D638-02a type V was performed on the composite specimen. Modulus of elasticity was determined using hyperbolic tangent function, and the results were compared to the sets of finite element analyses. Main effects of RVE parameters and their interactions were demonstrated and discussed, specially regarding the inclusion of two adjacent wood particles within one unit cell of the material. Regression analysis was performed to mathematically model the RVE parameter effects and their interactions over the modulus of elasticity response. The model was finally employed in an optimization analysis to arrive at an optimal set of RVE parameters that minimizes the difference between the predicted and experimental moduli of elasticity.

Large deflection analysis of laminated composite plates resting on nonlinear elastic foundations by the method of discrete singular convolution

International Nuclear Information System (INIS)

Baltacioglu, A.K.; Civalek, O.; Akgoez, B.; Demir, F.

2011-01-01

This paper presents nonlinear static analysis of a rectangular laminated composite thick plate resting on nonlinear two-parameter elastic foundation with cubic nonlinearity. The plate formulation is based on first-order shear deformation theory (FSDT). The governing equation of motion for a rectangular laminated composite thick plate is derived by using the von Karman equation. The nonlinear static deflections of laminated plates on elastic foundation are investigated using the discrete singular convolution method. The effects of foundation and geometric parameters of plates on nonlinear deflections are investigated. The validity of the present method is demonstrated by comparing the present results with those available in the literature. - Highlights: → Large deflection analysis of laminated composite plates are investigated. → As foundation, nonlinear elastic models have been used firstly. → The effects of three-parameter foundation are investigated in detail.

Characterization of elastic-viscoplastic properties of an AS4/PEEK thermoplastic composite

Science.gov (United States)

Yoon, K. J.; Sun, C. T.

1991-01-01

The elastic-viscoplastic properties of an AS4/PEEK (APC-2) thermoplastic composite were characterized at 24 C (75 F) and 121 C (250 F) by using a one-parameter viscoplasticity model. To determine the strain-rate effects, uniaxial tension tests were performed on unidirectional off-axis coupon specimens with different monotonic strain rates. A modified Bodner and Partom's model was also used to describe the viscoplasticity of the thermoplastic composite. The experimental results showed that viscoplastic behavior can be characterized quite well using the one-parameter overstress viscoplasticity model.

Dispersion Differences and Consistency of Artificial Periodic Structures.

Science.gov (United States)

Cheng, Zhi-Bao; Lin, Wen-Kai; Shi, Zhi-Fei

2017-10-01

Dispersion differences and consistency of artificial periodic structures, including phononic crystals, elastic metamaterials, as well as periodic structures composited of phononic crystals and elastic metamaterials, are investigated in this paper. By developing a K(ω) method, complex dispersion relations and group/phase velocity curves of both the single-mechanism periodic structures and the mixing-mechanism periodic structures are calculated at first, from which dispersion differences of artificial periodic structures are discussed. Then, based on a unified formulation, dispersion consistency of artificial periodic structures is investigated. Through a comprehensive comparison study, the correctness for the unified formulation is verified. Mathematical derivations of the unified formulation for different artificial periodic structures are presented. Furthermore, physical meanings of the unified formulation are discussed in the energy-state space.

Body composition influenced by progressive elastic band resistance exercise of sarcopenic obesity elderly women: a pilot randomized controlled trial.

Science.gov (United States)

Huang, Shih-Wei; Ku, Jan-Wen; Lin, Li-Fong; Liao, Chun-De; Chou, Lin-Chuan; Liou, Tsan-Hon

2017-08-01

Sarcopenia involves age-related decreases in muscle strength and muscle mass, leading to frailty and disability in elderly people. When combined with obesity, it is defined as sarcopenic obesity (SO), which can result in more functional limitations and metabolic disorders than either disorder alone. The aim of this study was to investigate body composition changes after elastic band resistance training in elderly women with SO. Randomized single-blinded (assessor blinded) controlled pilot trial. Academic medical center. Thirty-five elderly (>60 years old) women with SO. This pilot randomized controlled trial focused on elderly women with SO. The study group underwent progressive elastic band resistance training for 12 weeks (3 times per week). The control group received only a 40-minute lesson about the exercise concept. Dual-energy X-ray absorptiometry was performed before and after intervention to evaluate body composition. Mann-Whitney U and Wilcoxon signed rank tests were used to analyze the differences within and between these groups. In total, 35 elderly women with SO were enrolled and divided into study (N.=18) and control groups (N.=17). No difference was observed in age, biochemical parameters, or Body Mass Index between both groups. After the intervention, the fat proportion of body composition in the right upper extremity (P=0.03), left upper extremity (P=0.04), total fat (P=0.035), and fat percentage (P=0.012) had decreased, and bone mineral density (BMD) (P=0.026), T-score (P=0.028), and Z-score (P=0.021) had increased in the study group. Besides, statistical difference was observed in outcome measurements of right upper extremity (P=0.013), total fat (P=0.023), and fat percentage (P=0.012) between the groups. Our study demonstrated that progressive elastic band resistance exercise can reduce fat mass and increase BMD in elderly women with SO, and that this exercise program is feasible for this demographic. Additional studies with larger sample sizes

Fiber/collagen composites for ligament tissue engineering: influence of elastic moduli of sparse aligned fibers on mesenchymal stem cells.

Science.gov (United States)

Thayer, Patrick S; Verbridge, Scott S; Dahlgren, Linda A; Kakar, Sanjeev; Guelcher, Scott A; Goldstein, Aaron S

2016-08-01

Electrospun microfibers are attractive for the engineering of oriented tissues because they present instructive topographic and mechanical cues to cells. However, high-density microfiber networks are too cell-impermeable for most tissue applications. Alternatively, the distribution of sparse microfibers within a three-dimensional hydrogel could present instructive cues to guide cell organization while not inhibiting cell behavior. In this study, thin (∼5 fibers thick) layers of aligned microfibers (0.7 μm) were embedded within collagen hydrogels containing mesenchymal stem cells (MSCs), cultured for up to 14 days, and assayed for expression of ligament markers and imaged for cell organization. These microfibers were generated through the electrospinning of polycaprolactone (PCL), poly(ester-urethane) (PEUR), or a 75/25 PEUR/PCL blend to produce microfiber networks with elastic moduli of 31, 15, and 5.6 MPa, respectively. MSCs in composites containing 5.6 MPa fibers exhibited increased expression of the ligament marker scleraxis and the contractile phenotype marker α-smooth muscle actin versus the stiffer fiber composites. Additionally, cells within the 5.6 MPa microfiber composites were more oriented compared to cells within the 15 and 31 MPa microfiber composites. Together, these data indicate that the mechanical properties of microfiber/collagen composites can be tuned for the engineering of ligament and other target tissues. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 1894-1901, 2016. © 2016 Wiley Periodicals, Inc.

Characterization of elastic interactions in GaAs/Si composites by optically pumped nuclear magnetic resonance

Energy Technology Data Exchange (ETDEWEB)

Wood, Ryan M.; Tokarski, John T.; McCarthy, Lauren A.; Bowers, Clifford R., E-mail: bowers@chem.ufl.edu [Department of Chemistry, University of Florida, Gainesville, Florida 32611 (United States); Stanton, Christopher J. [Department of Physics, University of Florida, Gainesville, Florida 32611 (United States)

2016-08-28

Elastic interactions in GaAs/Si bilayer composite structures were studied by optically pumped nuclear magnetic resonance (OPNMR). The composites were fabricated by epoxy bonding of a single crystal of GaAs to a single crystal of Si at 373 K followed by selective chemical etching of the GaAs at room temperature to obtain a series of samples with GaAs thickness varying from 37 μm to 635 μm, while the Si support thickness remained fixed at 650 μm. Upon cooling to below 10 K, a biaxial tensile stress developed in the GaAs film due to differential thermal contraction. The strain perpendicular to the plane of the bilayer and localized near the surface of the GaAs was deduced from the quadrupolar splitting of the Gallium-71 OPNMR resonance. Strain relaxation by bowing of the composite was observed to an extent that depended on the relative thickness of the GaAs and Si layers. The variation of the strain with GaAs layer thickness was found to be in good agreement with a general analytical model for the elastic relationships in composite media.

Higher-order asymptotic homogenization of periodic materials with low scale separation

NARCIS (Netherlands)

Ameen, M.M.; Peerlings, R.H.J.; Geers, M.G.D

2016-01-01

In this work, we investigate the limits of classical homogenization theories pertaining to homogenization of periodic linear elastic composite materials at low scale separations and demonstrate the effectiveness of higher-order periodic homogenization in alleviating this limitation. Classical

Effects of corrugation shape on frequency band-gaps for longitudinal wave motion in a periodic elastic layer

DEFF Research Database (Denmark)

Sorokin, Vladislav

2016-01-01

The paper concerns determining frequency band-gaps for longitudinal wave motion in a periodic waveguide. The waveguide may be considered either as an elastic layer with variable thickness or as a rod with variable cross section. As a result, widths and locations of all frequency band-gaps are det......The paper concerns determining frequency band-gaps for longitudinal wave motion in a periodic waveguide. The waveguide may be considered either as an elastic layer with variable thickness or as a rod with variable cross section. As a result, widths and locations of all frequency band......, harmonic in the corrugation series. The revealed insights into the mechanism of band-gap formation can be used to predict locations and widths of all frequency band-gaps featured by any corrugation shape. These insights are general and can be valid also for other types of wave motion in periodic structures...

Preparation of Photocrosslinked Fish Elastin Polypeptide/Microfibrillated Cellulose Composite Gels with Elastic Properties for Biomaterial Applications

Directory of Open Access Journals (Sweden)

Shinya Yano

2015-01-01

Full Text Available Photocrosslinked hydrogels reinforced by microfibrillated cellulose (MFC were prepared from a methacrylate-functionalized fish elastin polypeptide and MFC dispersed in dimethylsulfoxide (DMSO. First, a water-soluble elastin peptide with a molecular weight of ca. 500 g/mol from the fish bulbus arteriosus was polymerized by N,N′-dicyclohexylcarbodiimide (DCC, a condensation reagent, and then modified with 2-isocyanatoethyl methacrylate (MOI to yield a photocrosslinkable fish elastin polypeptide. The product was dissolved in DMSO and irradiated with UV light in the presence of a radical photoinitiator. We obtained hydrogels successfully by substitution of DMSO with water. The composite gel with MFC was prepared by UV irradiation of the photocrosslinkable elastin polypeptide mixed with dispersed MFC in DMSO, followed by substitution of DMSO with water. The tensile test of the composite gels revealed that the addition of MFC improved the tensile properties, and the shape of the stress–strain curve of the composite gel became more similar to the typical shape of an elastic material with an increase of MFC content. The rheology measurement showed that the elastic modulus of the composite gel increased with an increase of MFC content. The cell proliferation test on the composite gel showed no toxicity.

Elastic stability of biaxially loaded longitudinally stiffened composite structures.

Science.gov (United States)

Viswanathan, A. V.; Tamekuni, M.; Tripp, L. L.

1973-01-01

A linear analysis method is presented for the elastic stability of structures of uniform cross section, that may be idealized as an assemblage of laminated plate-strips, flat and curved, and beams. Each plate-strip and beam covers the entire length of the structure and is simply supported on the edges normal to the longitudinal axis. Arbitrary boundary conditions may be specified on any external longitudinal side of plate-strips. The structure or selected plate-strips may be loaded in any desired combination of inplane biaxial loads. The analysis simultaneously considers all modes of instability and is applicable for the buckling of laminated composite structures. Some numerical results are presented to indicate possible applications.

Computational modeling of elastic properties of carbon nanotube/polymer composites with interphase regions. Part II: Mechanical modeling

KAUST Repository

Han, Fei; Azdoud, Yan; Lubineau, Gilles

2014-01-01

We present two modeling approaches for predicting the macroscopic elastic properties of carbon nanotubes/polymer composites with thick interphase regions at the nanotube/matrix frontier. The first model is based on local continuum mechanics

Study of Wood Plastic Composites elastic behaviour using full field measurements

Science.gov (United States)

Ben Mbarek, T.; Robert, L.; Hugot, F.; Orteu, J. J.; Sammouda, H.; Graciaa, A.; Charrier, B.

2010-06-01

In this study, the mechanical properties and microstructure of HDPE/wood fibre composites are investigated. The four-point bending and tensile behaviour of Wood Plastic Composite (WPC) with or without additive are studied by using full-field strain measurements by 3-D Digital Image Correlation (3-D DIC). A non-linear behaviour is shown. The modulus of elasticity (MOE) is calculated as the tangent at zero strain of a Maxwell-Bingham model fitted onto experimental data. Four-point bending tests are analyzed thanks to the spatial standard deviation of the longitudinal strain field to determine the degree of heterogeneity. Cyclic tensile tests have been performed in order to analyze the damage of the material. Moreover, Scanning Electron Microscope (SEM) is used to characterize the morphology of the wood fibre/HDPE matrix interface for specimens with maleic anhydride modified polyethylene additive (MAPE).

Detecting Damage in Composite Material Using Nonlinear Elastic Wave Spectroscopy Methods

Science.gov (United States)

Meo, Michele; Polimeno, Umberto; Zumpano, Giuseppe

2008-05-01

Modern aerospace structures make increasing use of fibre reinforced plastic composites, due to their high specific mechanical properties. However, due to their brittleness, low velocity impact can cause delaminations beneath the surface, while the surface may appear to be undamaged upon visual inspection. Such damage is called barely visible impact damage (BVID). Such internal damages lead to significant reduction in local strengths and ultimately could lead to catastrophic failures. It is therefore important to detect and monitor damages in high loaded composite components to receive an early warning for a well timed maintenance of the aircraft. Non-linear ultrasonic spectroscopy methods are promising damage detection and material characterization tools. In this paper, two different non-linear elastic wave spectroscopy (NEWS) methods are presented: single mode nonlinear resonance ultrasound (NRUS) and nonlinear wave modulation technique (NWMS). The NEWS methods were applied to detect delamination damage due to low velocity impact (<12 J) on various composite plates. The results showed that the proposed methodology appear to be highly sensitive to the presence of damage with very promising future NDT and structural health monitoring applications.

Computational modeling of elastic properties of carbon nanotube/polymer composites with interphase regions. Part I: Micro-structural characterization and geometric modeling

KAUST Repository

Han, Fei; Azdoud, Yan; Lubineau, Gilles

2014-01-01

A computational strategy to predict the elastic properties of carbon nanotube-reinforced polymer composites is proposed in this two-part paper. In Part I, the micro-structural characteristics of these nano-composites are discerned

Studying the influence of nanodiamonds over the elasticity of polymer/nanodiamond composites for biomedical application

Science.gov (United States)

Hikov, T.; Mitev, D.; Radeva, E.; Iglic, A.; Presker, R.; Daniel, M.; Sepitka, J.; Krasteva, N.; Keremidarska, M.; Cvetanov, I.; Pramatarova, L.

2014-12-01

The combined unique properties offered by organic and inorganic constituents within a single material on a nanoscale level make nanocomposites attractive for the next generation of biocompatible materials. The composite materials of the detonation nanodiamond/polymer type possess spatial organization of components with new structural features and physical properties, as well as complex functions due to the strong synergistic effects between the nanoparticles and the polymer [1]. The plasma polymerization (PP) method was chosen to obtain composites of silicon-based polymers, in which detonation generated nanodiamond (DND) particles were incorporated. The composite layers are homogeneous, chemically resistant, thermally and mechanically stable, thus allowing a large amount of biological components to be loaded onto their surface and to be used in tissue engineering, regenerative medicine, implants, stents, biosensors and other medical and biological devices. Mesenchymal stem cells (MSCs) are the main focus of research in regenerative medicine due to their extraordinary potential to differentiate into different kinds of cells including osteoblasts, which are needed for various bone disease treatments. However, for optimal usage of MSCs knowledge about the factors that influence their initial distribution in the human system, tissue-specific activation and afterwards differentiation into osteoblasts is required. In recent studies it was found that one of these factors is the elasticity of the substrates [2]. The choice of the proper material which specifically guides the differentiation of stem cells even in the absence of growth factors is very important when building modern strategy for bone regeneration. One of the reasons for there not being many studies in this area worldwide is the lack of suitable biomaterials which support these kinds of experiments. The goal of this study is to create substrates suitable for cell culture with a range of mechanical properties

Studying the influence of nanodiamonds over the elasticity of polymer/nanodiamond composites for biomedical application

International Nuclear Information System (INIS)

Hikov, T; Iglic, A; Presker, R; Daniel, M; Sepitka, J; Krasteva, N; Keremidarska, M; Mitev, D; Radeva, E; Cvetanov, I; Pramatarova, L

2014-01-01

The combined unique properties offered by organic and inorganic constituents within a single material on a nanoscale level make nanocomposites attractive for the next generation of biocompatible materials. The composite materials of the detonation nanodiamond/polymer type possess spatial organization of components with new structural features and physical properties, as well as complex functions due to the strong synergistic effects between the nanoparticles and the polymer [1]. The plasma polymerization (PP) method was chosen to obtain composites of silicon-based polymers, in which detonation generated nanodiamond (DND) particles were incorporated. The composite layers are homogeneous, chemically resistant, thermally and mechanically stable, thus allowing a large amount of biological components to be loaded onto their surface and to be used in tissue engineering, regenerative medicine, implants, stents, biosensors and other medical and biological devices. Mesenchymal stem cells (MSCs) are the main focus of research in regenerative medicine due to their extraordinary potential to differentiate into different kinds of cells including osteoblasts, which are needed for various bone disease treatments. However, for optimal usage of MSCs knowledge about the factors that influence their initial distribution in the human system, tissue-specific activation and afterwards differentiation into osteoblasts is required. In recent studies it was found that one of these factors is the elasticity of the substrates [2]. The choice of the proper material which specifically guides the differentiation of stem cells even in the absence of growth factors is very important when building modern strategy for bone regeneration. One of the reasons for there not being many studies in this area worldwide is the lack of suitable biomaterials which support these kinds of experiments. The goal of this study is to create substrates suitable for cell culture with a range of mechanical properties

Elastic metamaterials and dynamic homogenization: a review

Directory of Open Access Journals (Sweden)

Ankit Srivastava

2015-01-01

Full Text Available In this paper, we review the recent advances which have taken place in the understanding and applications of acoustic/elastic metamaterials. Metamaterials are artificially created composite materials which exhibit unusual properties that are not found in nature. We begin with presenting arguments from discrete systems which support the case for the existence of unusual material properties such as tensorial and/or negative density. The arguments are then extended to elastic continuums through coherent averaging principles. The resulting coupled and nonlocal homogenized relations, called the Willis relations, are presented as the natural description of inhomogeneous elastodynamics. They are specialized to Bloch waves propagating in periodic composites and we show that the Willis properties display the unusual behavior which is often required in metamaterial applications such as the Veselago lens. We finally present the recent advances in the area of transformation elastodynamics, charting its inspirations from transformation optics, clarifying its particular challenges, and identifying its connection with the constitutive relations of the Willis and the Cosserat types.

The effective Schroedinger equation of the optical model of composite nuclei elastic collisions

International Nuclear Information System (INIS)

Mondragon, A.; Hernandez, E.

1980-01-01

An effective hamiltonian for elastic collisions between composite nuclei is obtained from the Schroedinger equation of the complete many-body system and its fully antisymmetric wave functions by means of a projection operator technique. This effective hamiltonian, defined in such a way that it has to reproduce the scattering amplitude in full detail, including exchange effects, is explicitly Galilean invariant. The effective interaction operator is a function of the relative distance between the centers of mass of the colliding nuclei and the constants of the motion of the whole system. The interaction operator of the optical model is obtained next, requiring as usual, that it reproduces the average over the energy of the scattering amplitude and keeping the Galilean invariance. The resulting optical potential operator has some terms identical to those obtained in the Resonating Group Method, and others coming from the elimination of all non elastic channels and the delayed elastic scattering. This result makes the relation existing among the projection operator method to the Feshbach and the cluster model equations of motion for positive energies (RGM) explicit. The additional interaction terms due to the flux loss in the elastic channel are non-local, and non-hermitean operators expressed in terms of the transition amplitudes and the density of states of the compound nucleus in such a way that an approximate evaluation, in a systematic fashion, seems possible. Theangular momentum dependence of the optical potential operator is discussed in some detail. (author)

Computational modeling of elastic properties of carbon nanotube/polymer composites with interphase regions. Part II: Mechanical modeling

KAUST Repository

Han, Fei

2014-01-01

We present two modeling approaches for predicting the macroscopic elastic properties of carbon nanotubes/polymer composites with thick interphase regions at the nanotube/matrix frontier. The first model is based on local continuum mechanics; the second one is based on hybrid local/non-local continuum mechanics. The key computational issues, including the peculiar homogenization technique and treatment of periodical boundary conditions in the non-local continuum model, are clarified. Both models are implemented through a three-dimensional geometric representation of the carbon nanotubes network, which has been detailed in Part I. Numerical results are shown and compared for both models in order to test convergence and sensitivity toward input parameters. It is found that both approaches provide similar results in terms of homogenized quantities but locally can lead to very different microscopic fields. © 2013 Elsevier B.V. All rights reserved.

Study of Wood Plastic Composites elastic behaviour using full field measurements

Directory of Open Access Journals (Sweden)

Graciaa A.

2010-06-01

Full Text Available In this study, the mechanical properties and microstructure of HDPE/wood fibre composites are investigated. The four-point bending and tensile behaviour of Wood Plastic Composite (WPC with or without additive are studied by using full-field strain measurements by 3-D Digital Image Correlation (3-D DIC. A non-linear behaviour is shown. The modulus of elasticity (MOE is calculated as the tangent at zero strain of a Maxwell-Bingham model fitted onto experimental data. Four-point bending tests are analyzed thanks to the spatial standard deviation of the longitudinal strain field to determine the degree of heterogeneity. Cyclic tensile tests have been performed in order to analyze the damage of the material. Moreover, Scanning Electron Microscope (SEM is used to characterize the morphology of the wood fibre/HDPE matrix interface for specimens with maleic anhydride modified polyethylene additive (MAPE.

Elastic and Sorption Characteristics of an Epoxy Binder in a Composite During Its Moistening

Science.gov (United States)

Aniskevich, K.; Glaskova, T.; Jansons, J.

2005-07-01

Results of an experimental investigation into the elastic and sorption characteristics of a model composite material (CM) — epoxy resin filled with LiF crystals — during its moistening are presented. Properties of the binder in the CM with different filler contents ( v f = 0, 0.05, 0.11, 0.23, 0.28, 0.33, 0.38, and 0.46) were evaluated indirectly by using known micromechanical models of CMs. It was revealed that, for the CM in a conditionally initial state, the elastic modulus of the binder in it and the filler microstrain (change in the interplanar distance in the crystals, measured by the X-ray method) as functions of filler content had the same character. The elastic modulus of the binder in the CM with a low filler content was equal to that for the binder in a block; the elastic modulus of the binder in the CM decreased with increasing filler content. The maximum (corresponding to water saturation of the CM) stresses in the binder and the filler microstresses as functions of filler content were of the same character. Moreover, the absolute values of maximum stresses in the binder and of filler microstresses coincided for high and low contents of the filler. At v f = 0.2-0. 3, the filler microstrains exceeded the stresses in the binder. The effect of moisture on the epoxy binder in the CM with a high filler content was not entirely reversible: the elastic characteristics of the binder increased, the diffusivity decreased, and the ultimate water content increased after a moistening-drying cycle.

Elastic and thermo-physical properties of TiC, TiN, and their intermediate composition alloys using ab initio calculations

International Nuclear Information System (INIS)

Kim, Jiwoong; Kang, Shinhoo

2012-01-01

Highlights: ► Elastic properties of TiC, TiN and their alloys were calculated by ab initio calculations. ► Debye temperature and Gruneisen constant of TiC, TiN and their alloys were calculated as a function of nitrogen content. ► Thermo-physical properties were calculated as a function of nitrogen content. ► Thermal expansion of the alloys was fitted in different temperature range. - Abstract: The equilibrium lattice parameters, elastic properties, material brittleness, heat capacities, and thermal expansion coefficients of TiC, TiN, and their intermediate composition alloys (Ti(C 1−x N x ), x = 0.25, 0.5, and 0.75) were calculated using ab initio density functional theory (DFT) methods. We employed the Debye–Gruneisen model to calculate a finite temperature heat capacity and thermal expansion coefficient. The calculated elastic moduli and thermal expansion coefficients agreed well with the experimental data and with other DFT calculations. Accurate heat capacities of TiC, TiN, and their intermediate composition alloys were obtained by calculating not only the phonon contributions but also the electron contributions to the heat capacity. Our calculations indicated that the heat capacity differences between each composition originated mainly from the electronic contributions.

Comfort and Functional Properties of Far-Infrared/Anion-Releasing Warp-Knitted Elastic Composite Fabrics Using Bamboo Charcoal, Copper, and Phase Change Materials

Directory of Open Access Journals (Sweden)

Ting-Ting Li

2016-02-01

Full Text Available Elastic warp-knitted composite fabrics with far-infrared emissivity and an anion-releasing property were prepared using bamboo charcoal (BC, copper (Cu, and phase-change material (PCM. The functional composite fabric, which was composed of self-made complex yarns with various twisting degrees and material composition, were created using a rotor twister and ring-spinning technique. The fabric structure was diversified by the feeding modes of weft yarn into a crochet-knitting machine. The twist number of complex yarns was optimized by tensile tenacity, twist contraction, and hairiness, and analysis showed that twisting at 12 twists per inch produced the highest tensile tenacity and appropriate twist contraction and hairiness. Comfort evaluation showed that the elastic composite fabrics with BC weft yarns exhibited higher water–vapor transmission rate and air permeability, reaching 876 g/m2∙ day and 73.2 cm3/s/cm2, respectively. Three structures of composite fabric with various weft yarns had >0.85 ε far-infrared emissivity and 350–420 counts/cm3 anion amount. The prepared elastic warp-knitted fabrics can provide a comfortable, dry, and breathable environment to the wearer and can thus be applied as health-care textiles in the future.

Sound transmission through lined, composite panel structures: Transversely isotropic poro-elastic model

Science.gov (United States)

Kim, Jeong-Woo

A joint experimental and analytical investigation of the sound transmission loss (STL) and two-dimensional free wave propagation in composite sandwich panels is presented here. An existing panel, a Nomex honeycomb sandwich panel, was studied in detail. For the purpose of understanding the typical behavior of sandwich panels, a composite structure comprising two aluminum sheets with a relatively soft, poro-elastic foam core was also constructed and studied. The cores of both panels were modeled using an anisotropic (transversely isotropic) poro-elastic material theory. Several estimation methods were used to obtain the material properties of the honeycomb core and the skin plates to be used in the numerical calculations. Appropriate values selected from among the estimates were used in the STL and free wave propagation models. The prediction model was then verified in two ways: first, the calculated wave speeds and STL of a single poro-elastic layer were numerically verified by comparison with the predictions of a previously developed isotropic model. Secondly, to physically validate the transversely isotropic model, the measured STL and the phase speeds of the sandwich panels were compared with their predicted values. To analyze the actual treatment of a fuselage structure, multi-layered configurations, including a honeycomb panel and several layers such as air gaps, acoustic blankets and membrane partitions, were formulated. Then, to find the optimal solution for improving the sound barrier performance of an actual fuselage system, air layer depth and glass fiber lining effects were investigated by using these multi-layer models. By using the free wave propagation model, the first anti-symmetric and symmetric modes of the sandwich panels were characterized to allow the identification of the coincidence frequencies of the sandwich panel. The behavior of the STL could then be clearly explained by comparison with the free wave propagation solutions. By performing a

The multiple V-shaped double peeling of elastic thin films from elastic soft substrates

Science.gov (United States)

Menga, N.; Afferrante, L.; Pugno, N. M.; Carbone, G.

2018-04-01

In this paper, a periodic configuration of V-shaped double peeling process is investigated. Specifically, an elastic thin film is detached from a soft elastic material by applying multiple concentrated loads periodically distributed with spatial periodicity λ. The original Kendall's idea is extended to take into account the change in elastic energy occurring in the substrate when the detachment fronts propagate. The symmetric configuration typical of a V-peeling process causes the energy release rate to be sensitive to variations of the elastic energy stored in the soft substrate. This results in an enhancement of the adhesion strength because part of the external work required to trigger the peeling mechanism is converted in substrate elastic energy. A key role is played by both spatial periodicity λ and elasticity ratio E/Eh, between tape and substrate elastic moduli, in determining the conditions of stable adhesion. Indeed, the presence of multiple peeling fronts determines a modification of the mechanism of interaction, because deformations close to each peeling front are also affected by the stresses related to the other fronts. Results show that the energy release rate depends on the detached length of the tape so that conditions can be established which lead to an increase of the supported load compared to the classical peeling on rigid substrates. Finally, we also find that for any given value of the load per unit length, an optimum value of the wavelength λ exists that maximizes the tolerance of the system, before unstable propagation of the peeling front can occur.

Process Modelling of Curing Process-Induced Internal Stress and Deformation of Composite Laminate Structure with Elastic and Viscoelastic Models

Science.gov (United States)

Li, Dongna; Li, Xudong; Dai, Jianfeng

2018-06-01

In this paper, two kinds of transient models, the viscoelastic model and the linear elastic model, are established to analyze the curing deformation of the thermosetting resin composites, and are calculated by COMSOL Multiphysics software. The two models consider the complicated coupling between physical and chemical changes during curing process of the composites and the time-variant characteristic of material performance parameters. Subsequently, the two proposed models are implemented respectively in a three-dimensional composite laminate structure, and a simple and convenient method of local coordinate system is used to calculate the development of residual stresses, curing shrinkage and curing deformation for the composite laminate. Researches show that the temperature, degree of curing (DOC) and residual stresses during curing process are consistent with the study in literature, so the curing shrinkage and curing deformation obtained on these basis have a certain referential value. Compared the differences between the two numerical results, it indicates that the residual stress and deformation calculated by the viscoelastic model are more close to the reference value than the linear elastic model.

Aeroelastic response and stability of tiltrotors with elastically-coupled composite rotor blades. Ph.D. Thesis

Science.gov (United States)

Nixon, Mark W.

1993-01-01

There is a potential for improving the performance and aeroelastic stability of tiltrotors through the use of elastically-coupled composite rotor blades. To study the characteristics of tiltrotors with these types of rotor blades it is necessary to formulate a new analysis which has the capabilities of modeling both a tiltrotor configuration and an anisotropic rotor blade. Background for these formulations is established in two preliminary investigations. In the first, the influence of several system design parameters on tiltrotor aeroelastic stability is examined for the high-speed axial flight mode using a newly-developed rigid-blade analysis with an elastic wing finite element model. The second preliminary investigation addresses the accuracy of using a one-dimensional beam analysis to predict frequencies of elastically-coupled highly-twisted rotor blades. Important aspects of the new aeroelastic formulations are the inclusion of a large steady pylon angle which controls tilt of the rotor system with respect to the airflow, the inclusion of elastic pitch-lag coupling terms related to rotor precone, the inclusion of hub-related degrees of freedom which enable modeling of a gimballed rotor system and engine drive-train dynamics, and additional elastic coupling terms which enable modeling of the anisotropic features for both the rotor blades and the tiltrotor wing. Accuracy of the new tiltrotor analysis is demonstrated by a comparison of the results produced for a baseline case with analytical and experimental results reported in the open literature. Two investigations of elastically tailored blades on a baseline tiltrotor are then conducted. One investigation shows that elastic bending-twist coupling of the rotor blade is a very effective means for increasing the flutter velocity of a tiltrotor, and the magnitude of coupling required does not have an adverse effect on performance or blade loads. The second investigation shows that passive blade twist control via

Thermodynamic parameters of elasticity and electrical conductivity ...

African Journals Online (AJOL)

The thermodynamic parameters (change in free energy of elasticity, DGe; change in enthalpy of elasticity, DHe; and change in entropy of elasticity, DSe) and the electrical conductivity of natural rubber composites reinforced separately with some agricultural wastes have been determined. Results show that the reinforced ...

Characterization of elasticity and hydration of composite hydrogel based on collagen-iota carrageenan as a corneal tissue engineering

Science.gov (United States)

Rinawati, M.; Triastuti, J.; Pursetyo, K. T.

2018-04-01

The cornea is a refractive element of the eye that serves to continue the stimulation of light into the eye it has a clear, transparent, elastic and relatively thick tissue. Factors caused corneal blindness, are dystrophy, keratoconus, corneal scaring. Hydrogels can be made from polysaccharide derivatives that have gelation properties such as iota carrageenan. Therefore, it is a need to develop composite hydrogel based collagen-iota carragenan as an engineeried corneal tissue with high elasticity and hydration properties. Collagen hydrogel has a maximum water content an has equlibrium up to 40 %, less than the human cornea, 81 % and under normal hydration conditions, the human cornea can transmit 87 % of visible light. In addition, the refractive index on the surface of the cornea with air is 1.375-1.380. Based on this study, it is necessary to conduct research on the development and composition of hydrogel composite collagen-iota carrageen hydrogen based on. The best result was K5 (5:5) treatment, which has the equilibrium water content of 87.07 % and viscosity of 10.7346 Pa.s.

Optimal determination of the elastic constants of composite materials from ultrasonic wave-speed measurements

Science.gov (United States)

Castagnède, Bernard; Jenkins, James T.; Sachse, Wolfgang; Baste, Stéphane

1990-03-01

A method is described to optimally determine the elastic constants of anisotropic solids from wave-speeds measurements in arbitrary nonprincipal planes. For such a problem, the characteristic equation is a degree-three polynomial which generally does not factorize. By developing and rearranging this polynomial, a nonlinear system of equations is obtained. The elastic constants are then recovered by minimizing a functional derived from this overdetermined system of equations. Calculations of the functional are given for two specific cases, i.e., the orthorhombic and the hexagonal symmetries. Some numerical results showing the efficiency of the algorithm are presented. A numerical method is also described for the recovery of the orientation of the principal acoustical axes. This problem is solved through a double-iterative numerical scheme. Numerical as well as experimental results are presented for a unidirectional composite material.

Numerical computing of elastic homogenized coefficients for periodic fibrous tissue

Directory of Open Access Journals (Sweden)

Roman S.

2009-06-01

Full Text Available The homogenization theory in linear elasticity is applied to a periodic array of cylindrical inclusions in rectangular pattern extending to infinity in the inclusions axial direction, such that the deformation of tissue along this last direction is negligible. In the plane of deformation, the homogenization scheme is based on the average strain energy whereas in the third direction it is based on the average normal stress along this direction. Namely, these average quantities have to be the same on a Repeating Unit Cell (RUC of heterogeneous and homogenized media when using a special form of boundary conditions forming by a periodic part and an affine part of displacement. It exists an infinity of RUCs generating the considered array. The computing procedure is tested with different choices of RUC to control that the results of the homogenization process are independent of the kind of RUC we employ. Then, the dependence of the homogenized coefficients on the microstructure can be studied. For instance, a special anisotropy and the role of the inclusion volume are investigated. In the second part of this work, mechanical traction tests are simulated. We consider two kinds of loading, applying a density of force or imposing a displacement. We test five samples of periodic array containing one, four, sixteen, sixty-four and one hundred of RUCs. The evolution of mean stresses, strains and energy with the numbers of inclusions is studied. Evolutions depend on the kind of loading, but not their limits, which could be predicted by simulating traction test of the homogenized medium.

Bioconductive 3D nano-composite constructs with tunable elasticity to initiate stem cell growth and induce bone mineralization

Energy Technology Data Exchange (ETDEWEB)

Sagar, Nitin [Department of Biosciences and Bioengineering, Indian Institute of Technology-Bombay, Mumbai 400076 (India); Khanna, Kunal [Centre for Research in Nanotechnology and Science, Indian Institute of Technology-Bombay, Mumbai 400076 (India); Sardesai, Varda S. [National Institute of Research in Reproductive Health, Mumbai 400012 (India); Singh, Atul K. [Centre for Research in Nanotechnology and Science, Indian Institute of Technology-Bombay, Mumbai 400076 (India); Temgire, Mayur; Kalita, Mridula Phukan [Department of Chemical Engineering, Indian Institute of Technology-Bombay, Mumbai 400076 (India); Kadam, Sachin S. [Department of Chemical Engineering, Indian Institute of Technology-Bombay, Mumbai 400076 (India); Krishna Institute of Medical Sciences, Malkapur, Karad 415539, Dist. Satara, Maharashtra (India); Soni, Vivek P. [Department of Biosciences and Bioengineering, Indian Institute of Technology-Bombay, Mumbai 400076 (India); Bhartiya, Deepa [National Institute of Research in Reproductive Health, Mumbai 400012 (India); Bellare, Jayesh R., E-mail: jb@iitb.ac.in [Department of Biosciences and Bioengineering, Indian Institute of Technology-Bombay, Mumbai 400076 (India); Centre for Research in Nanotechnology and Science, Indian Institute of Technology-Bombay, Mumbai 400076 (India); Department of Chemical Engineering, Indian Institute of Technology-Bombay, Mumbai 400076 (India); Wadhwani Research Center for Bioengineering, Indian Institute of Technology-Bombay, Mumbai 400076 (India)

2016-12-01

Bioactive 3D composites play an important role in advanced biomaterial design to provide molecular coupling and improve integrity with the cellular environment of the native bone. In the present study, a hybrid lyophilized polymer composite blend of anionic charged sodium salt of carboxymethyl chitin and gelatin (CMCh{sub Na}-GEL) reinforced with nano-rod agglomerated hydroxyapatite (nHA) has been developed with enhanced biocompatibility and tunable elasticity. The scaffolds have an open, uniform and interconnected porous structure with an average pore diameter of 157 ± 30 μm and 89.47 + 0.03% with four dimensional X-ray. The aspect ratio of ellipsoidal pores decrease from 4.4 to 1.2 with increase in gelatin concentration; and from 2.14 to 1.93 with decrease in gelling temperature. The samples were resilient with elastic stain at 1.2 MPa of stress also decreased from 0.33 to 0.23 with increase in gelatin concentration. The crosslinker HMDI (hexamethylene diisocyanate) yielded more resilient samples at 1.2 MPa in comparison to glutaraldehyde. Increased crosslinking time from 2 to 4 h in continuous compression cycle show no improvement in maximum elastic stain of 1.2 MPa stress. This surface elasticity of the scaffold enables the capacity of these materials for adherent self renewal and cultivation of the NTERA-2 cL.D1 (NT2/D1), pluripotent embryonal carcinoma cell with biomechanical surface, as is shown here. Proliferation with MG-63, ALP activity and Alizarin red mineralization assay on optimized scaffold demonstrated ***p < 0.001 between different time points thus showing its potential for bone healing. In pre-clinical study histological bone response of the scaffold construct displayed improved activity of bone regeneration in comparison to self healing of control groups (sham) up to week 07 after implantation in rabbit tibia critical-size defect. Therefore, this nHA-CMCh{sub Na}-GEL scaffold composite exhibits inherent and efficient physicochemical, mechanical

Bioconductive 3D nano-composite constructs with tunable elasticity to initiate stem cell growth and induce bone mineralization

International Nuclear Information System (INIS)

Sagar, Nitin; Khanna, Kunal; Sardesai, Varda S.; Singh, Atul K.; Temgire, Mayur; Kalita, Mridula Phukan; Kadam, Sachin S.; Soni, Vivek P.; Bhartiya, Deepa; Bellare, Jayesh R.

2016-01-01

Bioactive 3D composites play an important role in advanced biomaterial design to provide molecular coupling and improve integrity with the cellular environment of the native bone. In the present study, a hybrid lyophilized polymer composite blend of anionic charged sodium salt of carboxymethyl chitin and gelatin (CMCh Na -GEL) reinforced with nano-rod agglomerated hydroxyapatite (nHA) has been developed with enhanced biocompatibility and tunable elasticity. The scaffolds have an open, uniform and interconnected porous structure with an average pore diameter of 157 ± 30 μm and 89.47 + 0.03% with four dimensional X-ray. The aspect ratio of ellipsoidal pores decrease from 4.4 to 1.2 with increase in gelatin concentration; and from 2.14 to 1.93 with decrease in gelling temperature. The samples were resilient with elastic stain at 1.2 MPa of stress also decreased from 0.33 to 0.23 with increase in gelatin concentration. The crosslinker HMDI (hexamethylene diisocyanate) yielded more resilient samples at 1.2 MPa in comparison to glutaraldehyde. Increased crosslinking time from 2 to 4 h in continuous compression cycle show no improvement in maximum elastic stain of 1.2 MPa stress. This surface elasticity of the scaffold enables the capacity of these materials for adherent self renewal and cultivation of the NTERA-2 cL.D1 (NT2/D1), pluripotent embryonal carcinoma cell with biomechanical surface, as is shown here. Proliferation with MG-63, ALP activity and Alizarin red mineralization assay on optimized scaffold demonstrated ***p < 0.001 between different time points thus showing its potential for bone healing. In pre-clinical study histological bone response of the scaffold construct displayed improved activity of bone regeneration in comparison to self healing of control groups (sham) up to week 07 after implantation in rabbit tibia critical-size defect. Therefore, this nHA-CMCh Na -GEL scaffold composite exhibits inherent and efficient physicochemical, mechanical and

Non-periodic homogenization of 3-D elastic media for the seismic wave equation

Science.gov (United States)

Cupillard, Paul; Capdeville, Yann

2018-05-01

Because seismic waves have a limited frequency spectrum, the velocity structure of the Earth that can be extracted from seismic records has a limited resolution. As a consequence, one obtains smooth images from waveform inversion, although the Earth holds discontinuities and small scales of various natures. Within the last decade, the non-periodic homogenization method shed light on how seismic waves interact with small geological heterogeneities and `see' upscaled properties. This theory enables us to compute long-wave equivalent density and elastic coefficients of any media, with no constraint on the size, the shape and the contrast of the heterogeneities. In particular, the homogenization leads to the apparent, structure-induced anisotropy. In this paper, we implement this method in 3-D and show 3-D tests for the very first time. The non-periodic homogenization relies on an asymptotic expansion of the displacement and the stress involved in the elastic wave equation. Limiting ourselves to the order 0, we show that the practical computation of an upscaled elastic tensor basically requires (i) to solve an elastostatic problem and (ii) to low-pass filter the strain and the stress associated with the obtained solution. The elastostatic problem consists in finding the displacements due to local unit strains acting in all directions within the medium to upscale. This is solved using a parallel, highly optimized finite-element code. As for the filtering, we rely on the finite-element quadrature to perform the convolution in the space domain. We end up with an efficient numerical tool that we apply on various 3-D models to test the accuracy and the benefit of the homogenization. In the case of a finely layered model, our method agrees with results derived from Backus. In a more challenging model composed by a million of small cubes, waveforms computed in the homogenized medium fit reference waveforms very well. Both direct phases and complex diffracted waves are

How to determine composite material properties using numerical homogenization

DEFF Research Database (Denmark)

Andreassen, Erik; Andreasen, Casper Schousboe

2014-01-01

Numerical homogenization is an efficient way to determine effective macroscopic properties, such as the elasticity tensor, of a periodic composite material. In this paper an educational description of the method is provided based on a short, self-contained Matlab implementation. It is shown how...... the basic code, which computes the effective elasticity tensor of a two material composite, where one material could be void, is easily extended to include more materials. Furthermore, extensions to homogenization of conductivity, thermal expansion, and fluid permeability are described in detail. The unit...

Anisotropic failure and size effects in periodic honeycomb materials: A gradient-elasticity approach

Science.gov (United States)

Réthoré, Julien; Dang, Thi Bach Tuyet; Kaltenbrunner, Christine

2017-02-01

This paper proposes a fracture mechanics model for the analysis of crack propagation in periodic honeycomb materials. The model is based on gradient-elasticity which enables us to account for the effect of the material structure at the macroscopic scale. For simulating the propagation of cracks along an arbitrary path, the numerical implementation is elaborated based on an extended finite element method with the required level of continuity. The two main features captured by the model are directionality and size effect. The numerical predictions are consistent with experimental results on honeycomb materials but also with results reported in the literature for microstructurally short cracks in metals.

Transient Vibrations of an Elastic Cylinder Inserted in the Elastic Medium

Directory of Open Access Journals (Sweden)

Sulym Heorgij

2016-06-01

Full Text Available Using method of Laguerre polynomials we have obtained the solution of the dynamic problem of the theory of elasticity for elastic cylinder inserted into massive body modeled as a space. The source of non-stationary processes in composite is high intensity force load of the inner surface of the cylinder. On the surface separation of materials of space and cylinder the conditions of ideal mechanical contact are satisfied. The solution is obtained as series of Laguerre polynomials, which coefficients are found from recurrent relations. The results of numerical analysis of transient stress-strain state in elastic space with cylindrical insertion might be used for the technological process of hydraulic fracturing during shale gas extraction.

Analytic approximations for the elastic moduli of two-phase materials

DEFF Research Database (Denmark)

Zhang, Z. J.; Zhu, Y. K.; Zhang, P.

2017-01-01

Based on the models of series and parallel connections of the two phases in a composite, analytic approximations are derived for the elastic constants (Young's modulus, shear modulus, and Poisson's ratio) of elastically isotropic two-phase composites containing second phases of various volume...

Dynamic determination of modulus of elasticity of full-size wood composite panels using a vibration method

Science.gov (United States)

Cheng Guan; Houjiang Zhang; Lujing Zhou; Xiping Wang

2015-01-01

A vibration testing method based on free vibration theory in a ‘‘free–free” support condition was investigated for evaluating the modulus of elasticity (MOE) of full-size wood composite panels (WCPs). Vibration experiments were conducted on three types of WCPs (medium density fibreboard, particleboard, and plywood) to determine the dynamic MOE of the panels. Static...

Influence of composition of feed and lactation period on mineral composition of Mare's

Directory of Open Access Journals (Sweden)

Miroslav Fišera

2018-03-01

Full Text Available Normal 0 21 false false false CS X-NONE X-NONE Effects of lactation period and feed on essential minerals composition of mare's milk were studied. Average Ca, P, Na and Mg concentrations in feed DM were 0.66, 4.30, 0.13 and 2.21 g.kg-1 of DM (dry matter, respectively. In regard to milk all elements concentrations were not similar to each other due to the changes of the lactation day differences. Average Ca, P, Na and Mg concentrations (in DM caused by breed differences and lactation days were 1.95, 1.08, 0.53 and 0.22 g.kg-1, respectively. During the milk period, a high-quality feed were maintaining the major mineral composition of mare's milk in 1.5 - 2 times higher amount than milk of mare fed with pasture and a low-quality feed. The colostrum stage of mare was much shorter than other animals, the mare's milk on the 2nd day of lactation showed properties of initial milk in which its composition, particularly in minerals, were two times higher when compare to that on milk periods that was started from 5th day after parturition. It seemed that some factors, except well physiological conditions, such as mare's age, number of foaling, sex of foal etc. did not affect milk nutrient composition.

Propagation of steady-state vibration in periodic pipes conveying fluid on elastic foundations with external moving loads

Energy Technology Data Exchange (ETDEWEB)

Yu, Dianlong, E-mail: dianlongyu@yahoo.com.cn [Laboratory of Science and Technology on Integrated Logistics Support, National University of Defense Technology, Changsha 410073 (China); MOE Key Laboratory of Photonic and Phononic Crystals, National University of Defense Technology, Changsha 410073 (China); Wen, Jihong; Shen, Huijie; Wen, Xisen [Laboratory of Science and Technology on Integrated Logistics Support, National University of Defense Technology, Changsha 410073 (China); MOE Key Laboratory of Photonic and Phononic Crystals, National University of Defense Technology, Changsha 410073 (China)

2012-10-01

The propagation of steady-state vibration in a periodic pipe conveying fluid on elastic foundation with an external moving load is studied using wave propagation and attenuation theory. Wavenumbers and propagation properties in a moving coordinate system are investigated. The propagation constants are calculated using transfer matrix theory to determine whether the perturbation, which is introduced by an external moving load, can propagate through the pipe or not. The Bragg and locally resonant band gaps, corresponding to the velocity field, can exist in a periodic pipe system. In addition, the effects on both types of band gaps have been analysed.

Propagation of steady-state vibration in periodic pipes conveying fluid on elastic foundations with external moving loads

International Nuclear Information System (INIS)

Yu, Dianlong; Wen, Jihong; Shen, Huijie; Wen, Xisen

2012-01-01

The propagation of steady-state vibration in a periodic pipe conveying fluid on elastic foundation with an external moving load is studied using wave propagation and attenuation theory. Wavenumbers and propagation properties in a moving coordinate system are investigated. The propagation constants are calculated using transfer matrix theory to determine whether the perturbation, which is introduced by an external moving load, can propagate through the pipe or not. The Bragg and locally resonant band gaps, corresponding to the velocity field, can exist in a periodic pipe system. In addition, the effects on both types of band gaps have been analysed.

Effective medium of periodic fluid-solid composites

KAUST Repository

Mei, Jun; Wu, Ying; Liu, Zhengyou

2012-01-01

An analytic solution of the effective mass density and bulk modulus of a periodic fluid-solid composite is obtained by using the multiple-scattering theory in the long-wavelength limit. It is shown that when the concentration of solid inclusions

Oscillations of a Beam on a Non-Linear Elastic Foundation under Periodic Loads

Directory of Open Access Journals (Sweden)

Donald Mark Santee

2006-01-01

Full Text Available The complexity of the response of a beam resting on a nonlinear elastic foundation makes the design of this structural element rather challenging. Particularly because, apparently, there is no algebraic relation for its load bearing capacity as a function of the problem parameters. Such an algebraic relation would be desirable for design purposes. Our aim is to obtain this relation explicitly. Initially, a mathematical model of a flexible beam resting on a non-linear elastic foundation is presented, and its non-linear vibrations and instabilities are investigated using several numerical methods. At a second stage, a parametric study is carried out, using analytical and semi-analytical perturbation methods. So, the influence of the various physical and geometrical parameters of the mathematical model on the non-linear response of the beam is evaluated, in particular, the relation between the natural frequency and the vibration amplitude and the first period doubling and saddle-node bifurcations. These two instability phenomena are the two basic mechanisms associated with the loss of stability of the beam. Finally Melnikov's method is used to determine an algebraic expression for the boundary that separates a safe from an unsafe region in the force parameters space. It is shown that this can be used as a basis for a reliable engineering design criterion.

Elastic energy and metastable phase equilibria for coherent mixtures in cubic systems

International Nuclear Information System (INIS)

Williams, R.O.

1979-02-01

Expressions were derived for the elastic energy due to coherency for cubic systems for an isotropic structure and for (100) or (111) habit planes for a lamellar structure. For the metastable equilibria the usual tangent compositions are replaced by compositions that are tangent to the elastic energy curve. For a loss of coherency there is an energy decrease due to the elastic effects and a further decrease associated with compositional changes. Information contained within this treatment permits calculation of the x-ray diffraction effects for such structures

Influence of Body Composition on Gait Kinetics throughout Pregnancy and Postpartum Period

Science.gov (United States)

Branco, Marco; Santos-Rocha, Rita; Vieira, Filomena; Silva, Maria-Raquel; Aguiar, Liliana; Veloso, António P.

2016-01-01

Pregnancy leads to several changes in body composition and morphology of women. It is not clear whether the biomechanical changes occurring in this period are due exclusively to body composition and size or to other physiological factors. The purpose was to quantify the morphology and body composition of women throughout pregnancy and in the postpartum period and identify the contribution of these parameters on the lower limb joints kinetic during gait. Eleven women were assessed longitudinally, regarding anthropometric, body composition, and kinetic parameters of gait. Body composition and body dimensions showed a significant increase during pregnancy and a decrease in the postpartum period. In the postpartum period, body composition was similar to the 1st trimester, except for triceps skinfold, total calf area, and body mass index, with higher results than at the beginning of pregnancy. Regression models were developed to predict women's internal loading through anthropometric variables. Four models include variables associated with the amount of fat; four models include variables related to overall body weight; three models include fat-free mass; one model includes the shape of the trunk as a predictor variable. Changes in maternal body composition and morphology largely determine kinetic dynamics of the joints in pregnant women. PMID:27073713

Preliminary Study on Effect of Chemical Composition Alteration on Elastic Recovery and Stress Recovery of Nitrile Gloves

Directory of Open Access Journals (Sweden)

Tan Kai Yang

2018-01-01

Full Text Available Nitrile gloves are widely used in the medical and automobile field due to its superiority in hypo-allergic component and chemical resistance over natural latex gloves. However, poor elastic recovery of nitrile glove to compressive force also creates an aesthetic issue for customers with high levels of wrinkling after removing from glove box. This paper demonstrates the preliminary study on the varies chemical composition such as crosslinking agents, sulphur and zinc oxide, the accelerator agent added during curing process, and the rubber filler Titanium Dioxide, on the elastic recovery and stress relaxation in nitrile gloves manufacturing. These chemical were studied at different concentration level comparing the high and low level versus the normal production range. Due to the inconsistency in the analysis technique on the surface imaging, the elastic recovery result was unable to be quantified and was not conclusive at this point. The cross linking agents, sulphur and zinc oxide, and the accelerator agent, played a significant role in the mechanical strength of the gloves. Increment of these chemicals result in higher tensile strength, but a reduction in the elasticity of the materials in which causes a lesser elongation at break percentage for the gloves. Both cross-linkers demonstrate different behaviour where higher sulphur content, provide higher stress relaxation (SR% yet zinc oxide shows otherwise.

Periodate oxidation of nanoscaled magnetic dextran composites

International Nuclear Information System (INIS)

Hong Xia; Guo Wei; Yuan Hang; Li Jun; Liu Yanmei; Ma Lan; Bai Yubai; Li Tiejin

2004-01-01

Highly hydrophilic, uniform and nontoxic magnetic fluids consisting of magnetite (Fe 3 O 4 ) and dextran were prepared. A periodate oxidation method was used to further activate the magnetic dextran, forming magnetic polyaldehyde-dextran, which could be conjugated to biomolecules such as proteins or antibodies. Oxidated Magnetic dextran composites were characterized by TEM, XRD and SQUID magnetometry. Moreover, a flexible, rapid and simple method to detect aldehydes was introduced to the magnetic composite system by utilizing 2,4-dinitrophenylhydrazine reagent. The result of the quantitative analysis of aldehyde was given by thermogravimetric analysis and elemental analysis

Computation of the lamina stacking sequence effect on elastic moduli of a plain-weave Nicalon/SiC laminated composite with a [0/30/60] lay-up

International Nuclear Information System (INIS)

Zhao Wei; Yu Niann-i

1998-01-01

Estimation of the elastic modulus is important in engineering design. One difference between CFCCs (continuous fiber-reinforced ceramic-matrix composites), and CMCs (whisker, particulate, or short fiber-reinforced ceramic-matrix composites), is that the anisotropic behavior of CFCCs plays an important role in affecting their mechanical behavior. This feature may also contribute to the variation of elastic properties and strengths of CFCC. In this paper, a Fortran program is developed to quantify the lamina stacking sequence effect on the effective elastic moduli of the laminated CFCCs. The material for modeling is a plain-weave Nicalon fiber-reinforced silicon carbide (Nicalon/SiC) CFCCs. Results show that various stacking sequences within the CFCC (a [0/30/60] lay-up) will give different effective elastic moduli of the CFCCs. This trend leads to a variation of the slope of the linear portion on the flexural stress-strain curve, i.e., changing the position of the starting point of the non-linear portion, and the shape of the whole curve, which gives a different value of the peak stress in the curve. (orig.)

Quasi-experimental taxation elasticities of US gasoline demand

International Nuclear Information System (INIS)

Goel, R.K.

1994-01-01

Taxation elasticities provide inputs in public policy aimed at raising revenues. Using the quasi-experimental method, this paper calculates gasoline taxation elasticities for the USA over 1952-86. The medium (mean) elasticity over this period is found to be -0.075 (-0.122). However, the elasticity following the oil shock of 1973 is found to be statistically different from the pre-shock elasticity. Reasons for this change in elasticity are discussed. The implication of this analysis is that tax policies based on price elasticities, rather than on tax elasticities, might be using an inappropriate elasticity estimate and consequently misinterpreting the government's ability to raise tax revenues. (author)

Energy in elastic fiber embedded in elastic matrix containing incident SH wave

Science.gov (United States)

Williams, James H., Jr.; Nagem, Raymond J.

1989-01-01

A single elastic fiber embedded in an infinite elastic matrix is considered. An incident plane SH wave is assumed in the infinite matrix, and an expression is derived for the total energy in the fiber due to the incident SH wave. A nondimensional form of the fiber energy is plotted as a function of the nondimensional wavenumber of the SH wave. It is shown that the fiber energy attains maximum values at specific values of the wavenumber of the incident wave. The results obtained here are interpreted in the context of phenomena observed in acousto-ultrasonic experiments on fiber reinforced composite materials.

Resin composites

DEFF Research Database (Denmark)

Benetti, Ana Raquel; Peutzfeldt, Anne; Lussi, Adrian

2014-01-01

OBJECTIVE: To investigate how the modulus of elasticity of resin composites influences marginal quality in restorations submitted to thermocyclic and mechanical loading. METHODS: Charisma, Filtek Supreme XTE and Grandio were selected as they were found to possess different moduli of elasticity...... of resin composite (p=0.81) on the quality of dentine margins was observed, before or after loading. Deterioration of all margins was evident after loading (p....008). CONCLUSIONS: The resin composite with the highest modulus of elasticity resulted in the highest number of gap-free enamel margins but with an increased incidence of paramarginal enamel fractures. CLINICAL SIGNIFICANCE: The results from this study suggest that the marginal quality of restorations can...

The Measurement of Tax Elasticity in India: A Time Series Approach

OpenAIRE

Acharya, Hem

2011-01-01

Revenue generation is an important goal of tax reform. The built-in responsiveness of revenues to changes in income, tax elasticity, provides very critical information for tax policy formulation. This paper utilises a time series approach to empirically estimate tax elasticities for India for the period 1991-2010. Tax elasticities are computed for income, turnover, excise, import and total taxes for the post-reform period. The elasticity coefficients reveal a low responsiveness of taxes to i...

Brazilian sawn wood price and income elasticity

Directory of Open Access Journals (Sweden)

Rommel Noce

2010-09-01

Full Text Available This study estimated the sawn wood demand price and income elasticity. Specifically it was estimated the priceelasticity of sawn wood, the cross price elasticity of wood panels and the income elasticity of Brazilian GDP. A log-log model withcorrection through outline of the mobile average (MA(1 was used, adjusted for the period of 1971 to 2006, which showed to bestable, with satisfactory significance levels. It was observed that sawn wood demand is inelastic in relation to price and elastic inrelation to income.

Micromechanics-based determination of effective elastic properties of polymer bonded explosives

International Nuclear Information System (INIS)

Banerjee, Biswajit; Adams, D.O.

2003-01-01

Polymer bonded explosives are particulate composites containing a high volume fraction of stiff elastic explosive particles in a compliant viscoelastic binder. Since the volume fraction of particles can be greater than 0.9 and the modulus contrast greater than 20 000, rigorous bounds on the elastic moduli of the composite are an order of magnitude different from experimentally determined values. Analytical solutions are also observed to provide inaccurate estimates of effective elastic properties. Direct finite element approximations of effective properties require large computational resources because of the complexity of the microstructure of these composites. An alternative approach, the recursive cells method (RCM) is also explored in this work. Results show that the degree of discretization and the microstructures used in finite element models of PBXs can significantly affect the estimated Young's moduli

Homogenization in thermoelasticity: application to composite materials

Energy Technology Data Exchange (ETDEWEB)

Peyroux, R [Lab. de Mecanique et Genie Civil, Univ. Montpellier 2, 34 Montpellier (France); Licht, C [Lab. de Mecanique et Genie Civil, Univ. Montpellier 2, 34 Montpellier (France)

1993-11-01

One of the obstacles to the industrial use of metal matrix composite materials is the damage they rapidly undergo when they are subjected to cyclic thermal loadings; local thermal stresses of high level can develop, sometimes nearby or over the elastic limit, due to the mismatch of elastic and thermal coefficients between the fibers and the matrix. For the same reasons, early cracks can appear in composites like ceramic-ceramic. Therefore, we investigate the linear thermoelastic behaviour of heterogeneous materials, taking account of the isentropic coupling term in the heat conduction equation. In the case of periodic materials, recent results, using the homogenization theory, allowed us to describe macroscopic and microscopic behaviours of such materials. This paper is concerned with the numerical simulation of this problem by a finite element method, using a multiscale approach. (orig.).

Measurement of in-plane elasticity of live cell layers using a pressure sensor embedded microfluidic device

Science.gov (United States)

Lin, Chien-Han; Wang, Chien-Kai; Chen, Yu-An; Peng, Chien-Chung; Liao, Wei-Hao; Tung, Yi-Chung

2016-11-01

In various physiological activities, cells experience stresses along their in-plane direction when facing substrate deformation. Capability of continuous monitoring elasticity of live cell layers during a period is highly desired to investigate cell property variation during various transformations under normal or disease states. This paper reports time-lapsed measurement of live cell layer in-plane elasticity using a pressure sensor embedded microfluidic device. The sensor converts pressure-induced deformation of a flexible membrane to electrical signals. When cells are cultured on top of the membrane, flexural rigidity of the composite membrane increases and further changes the output electrical signals. In the experiments, human embryonic lung fibroblast (MRC-5) cells are cultured and analyzed to estimate the in-plane elasticity. In addition, the cells are treated with a growth factor to simulate lung fibrosis to study the effects of cell transformation on the elasticity variation. For comparison, elasticity measurement on the cells by atomic force microscopy (AFM) is also performed. The experimental results confirm highly anisotropic configuration and material properties of cells. Furthermore, the in-plane elasticity can be monitored during the cell transformation after the growth factor stimulation. Consequently, the developed microfluidic device provides a powerful tool to study physical properties of cells for fundamental biophysics and biomedical researches.

Extrapolation of bulk rock elastic moduli of different rock types to high pressure conditions and comparison with texture-derived elastic moduli

Science.gov (United States)

Ullemeyer, Klaus; Lokajíček, Tomás; Vasin, Roman N.; Keppler, Ruth; Behrmann, Jan H.

2018-02-01

In this study elastic moduli of three different rock types of simple (calcite marble) and more complex (amphibolite, micaschist) mineralogical compositions were determined by modeling of elastic moduli using texture (crystallographic preferred orientation; CPO) data, experimental investigation and extrapolation. 3D models were calculated using single crystal elastic moduli, and CPO measured using time-of-flight neutron diffraction at the SKAT diffractometer in Dubna (Russia) and subsequently analyzed using Rietveld Texture Analysis. To define extrinsic factors influencing elastic behaviour, P-wave and S-wave velocity anisotropies were experimentally determined at 200, 400 and 600 MPa confining pressure. Functions describing variations of the elastic moduli with confining pressure were then used to predict elastic properties at 1000 MPa, revealing anisotropies in a supposedly crack-free medium. In the calcite marble elastic anisotropy is dominated by the CPO. Velocities continuously increase, while anisotropies decrease from measured, over extrapolated to CPO derived data. Differences in velocity patterns with sample orientation suggest that the foliation forms an important mechanical anisotropy. The amphibolite sample shows similar magnitudes of extrapolated and CPO derived velocities, however the pattern of CPO derived velocity is closer to that measured at 200 MPa. Anisotropy decreases from the extrapolated to the CPO derived data. In the micaschist, velocities are higher and anisotropies are lower in the extrapolated data, in comparison to the data from measurements at lower pressures. Generally our results show that predictions for the elastic behavior of rocks at great depths are possible based on experimental data and those computed from CPO. The elastic properties of the lower crust can, thus, be characterized with an improved degree of confidence using extrapolations. Anisotropically distributed spherical micro-pores are likely to be preserved, affecting

Elastic Deployable Composite Tubular Roll-Out Boom, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Deployable Space Systems (DSS) has developed an affordable and ultra-lightweight elastically self-deployable Roll-Out Boom technology that provides affordability and...

Nonlinear Buckling Analysis of Functionally Graded Graphene Reinforced Composite Shallow Arches with Elastic Rotational Constraints under Uniform Radial Load.

Science.gov (United States)

Huang, Yonghui; Yang, Zhicheng; Liu, Airong; Fu, Jiyang

2018-05-28

The buckling behavior of functionally graded graphene platelet-reinforced composite (FG-GPLRC) shallow arches with elastic rotational constraints under uniform radial load is investigated in this paper. The nonlinear equilibrium equation of the FG-GPLRC shallow arch with elastic rotational constraints under uniform radial load is established using the Halpin-Tsai micromechanics model and the principle of virtual work, from which the critical buckling load of FG-GPLRC shallow arches with elastic rotational constraints can be obtained. This paper gives special attention to the effect of the GPL distribution pattern, weight fraction, geometric parameters, and the constraint stiffness on the buckling load. The numerical results show that all of the FG-GPLRC shallow arches with elastic rotational constraints have a higher buckling load-carrying capacity compared to the pure epoxy arch, and arches of the distribution pattern X have the highest buckling load among four distribution patterns. When the GPL weight fraction is constant, the thinner and larger GPL can provide the better reinforcing effect to the FG-GPLRC shallow arch. However, when the value of the aspect ratio is greater than 4, the flakiness ratio is greater than 103, and the effect of GPL's dimensions on the buckling load of the FG-GPLRC shallow arch is less significant. In addition, the buckling model of FG-GPLRC shallow arch with elastic rotational constraints is changed as the GPL distribution patterns or the constraint stiffness changes. It is expected that the method and the results that are presented in this paper will be useful as a reference for the stability design of this type of arch in the future.

Shear elastic modulus of magnetic gels with random distribution of magnetizable particles

Science.gov (United States)

Iskakova, L. Yu; Zubarev, A. Yu

2017-04-01

Magnetic gels present new type of composite materials with rich set of uniquie physical properties, which find active applications in many industrial and bio-medical technologies. We present results of mathematically strict theoretical study of elastic modulus of these systems with randomly distributed magnetizable particles in an elastic medium. The results show that an external magnetic field can pronouncedly increase the shear modulus of these composites.

Morphology, surface roughness, electron inelastic and quasi-elastic scattering in elastic peak electron spectroscopy of polymers

International Nuclear Information System (INIS)

Lesiak, B.; Kosinski, A.; Nowakowski, R.; Koever, L.; Toth, J.; Varga, D.; Cserny, I.; Sulyok, A.; Gergely, G.

2006-01-01

Complete text of publication follows. Elastic peak electron spectroscopy (EPES) deals with the interaction of electrons with atoms of a solid surface, studying the distribution of electrons backscattered elastically. The nearest vicinity of the elastic peak, (low kinetic energy region) reflects both, electron inelastic and quasi-elastic processes. The incident electrons produce surface excitations, inducing surface plasmons with the corresponding loss peaks separated by 1 - 20 eV energy from the elastic peak. Quasi-elastic losses result from the recoil of scattering atoms of different atomic number, Z. The respective energy shift and Doppler broadening of the elastic peak depend on Z, the primary electron energy, E, and the measurement geometry. Quantitative surface analytical application of EPES, such as determination of parameters describing electron transport, requires a comparison of experimental data with corresponding data derived from Monte Carlo (MC) simulation. Several problems occur in EPES studies of polymers. The intensity of elastic peak, considered in quantitative surface analysis, is influenced by both, the inelastic and quasi-elastic scattering processes (especially for hydrogen scattering atoms and primary electron energy above 1000 eV). An additional factor affecting the elastic peak intensity is the surface morphology and roughness. The present work compares the effect of these factors on the elastic peak intensity for selected polymers (polyethylene, polyaniline and polythiophenes). X-ray photoelectron spectroscopy (XPS) and helium pycnometry are applied for deriving the surface atomic composition and the bulk density, while scanning electron microscopy (SEM) and atomic force microscopy (AFM) for determining surface morphology and roughness. According to presented results, the influence of surface morphology and roughness is larger than those of surface excitations or recoil of hydrogen atoms. The component due to recoil of hydrogen atoms can be

In vitro comparison of the force degradation of orthodontic intramural elastic from different compositions

OpenAIRE

Vieira, Camilla Ivini Viana [UNESP; Oliveira, Cibele Braga de [UNESP; Ribeiro, Alexandre Antonio [UNESP; Caldas, Sergei Godeiro Fernandes Rabelo [UNESP; Martins, Lídia Parsekian [UNESP; Gandini Júnior, Luiz Gonzaga [UNESP; Santos-Pinto, Ary dos [UNESP

2013-01-01

Introduction and Objective: The synthetic intermaxillary elastic emerged as an alternative for clinical use in patients with latex sensitivity. However, there are disagreements about this elastic protocol use according to the force degradation. The aim of this study was to evaluate, in vitro, the forces generated by latex and synthetic elastics over time. Material and methods: Sample size of 840 elastics were used (420 latex and 420 synthetic), delivering medium strength (Dental Morelli®) wit...

In vitro comparison of the force degradation of orthodontic intraoral elastics from different compositions

OpenAIRE

Vieira, Camila Ivini Viana [UNESP; Oliveira, Cibele Braga [UNESP; Ribeiro, Alexandre Antonio [UNESP; Caldas, Sergei Godeiro Fernandes Rabelo [UNESP; Martins, Lídia Parsekian [UNESP; Gandini Júnior, Luiz Gonzaga [UNESP; Santos-Pinto, Ary dos [UNESP

2013-01-01

Introduction and Objective: The synthetic intermaxillary elastic emerged as an alternative for clinical use in patients with latex sensitivity. However, there are disagreements about this elastic protocol use according to the force degradation. The aim of this study was to evaluate, in vitro, the forces generated by latex and synthetic elastics over time. Material and methods: Sample size of 840 elastics were used (420 latex and 420 synthetic), delivering medium strength (Dental Morelli®) wi...

Effective thermoelastic properties of composites with periodicity in cylindrical coordinates

KAUST Repository

Chatzigeorgiou, George

2012-09-01

The aim of this work is to study composites that present cylindrical periodicity in the microstructure. The effective thermomechanical properties of these composites are identified using a modified version of the asymptotic expansion homogenization method, which accounts for unit cells with shell shape. The microscale response is also shown. Several numerical examples demonstrate the use of the proposed approach, which is validated by other micromechanics methods. © 2012 Elsevier Ltd. All rights reserved.

Computational Homogenization of Mechanical Properties for Laminate Composites Reinforced with Thin Film Made of Carbon Nanotubes

Science.gov (United States)

El Moumen, A.; Tarfaoui, M.; Lafdi, K.

2018-06-01

Elastic properties of laminate composites based Carbone Nanotubes (CNTs), used in military applications, were estimated using homogenization techniques and compared to the experimental data. The composite consists of three phases: T300 6k carbon fibers fabric with 5HS (satin) weave, baseline pure Epoxy matrix and CNTs added with 0.5%, 1%, 2% and 4%. Two step homogenization methods based RVE model were employed. The objective of this paper is to determine the elastic properties of structure starting from the knowledge of those of constituents (CNTs, Epoxy and carbon fibers fabric). It is assumed that the composites have a geometric periodicity and the homogenization model can be represented by a representative volume element (RVE). For multi-scale analysis, finite element modeling of unit cell based two step homogenization method is used. The first step gives the properties of thin film made of epoxy and CNTs and the second is used for homogenization of laminate composite. The fabric unit cell is chosen using a set of microscopic observation and then identified by its ability to enclose the characteristic periodic repeat in the fabric weave. The unit cell model of 5-Harness satin weave fabric textile composite is identified for numerical approach and their dimensions are chosen based on some microstructural measurements. Finally, a good comparison was obtained between the predicted elastic properties using numerical homogenization approach and the obtained experimental data with experimental tests.

Elastic wave manipulation by using a phase-controlling meta-layer

Science.gov (United States)

Shen, Xiaohui; Sun, Chin-Teh; Barnhart, Miles V.; Huang, Guoliang

2018-03-01

In this work, a high pass meta-layer for elastic waves is proposed. An elastic phase-controlling meta-layer is theoretically realized using parallel and periodically arranged metamaterial sections based on the generalized Snell's law. The elastic meta-layer is composed of periodically repeated supercells, in which the frequency dependent elastic properties of the metamaterial are used to control a phase gradient at the interface between the meta-layer and conventional medium. It is analytically and numerically demonstrated that with a normal incident longitudinal wave, the wave propagation characteristics can be directly manipulated by the periodic length of the meta-layer element at the sub-wavelength scale. It is found that propagation of the incident wave through the interface is dependent on whether the working wavelength is longer or shorter than the periodic length of the meta-layer element. Specifically, a mode conversion of the P-wave to an SV-wave is investigated as the incident wave passes through the meta-layer region. Since the most common and damaging elastic waves in civil and mechanical industries are in the low frequency region, the work in this paper has great potential in the seismic shielding, engine vibration isolation, and other highly dynamic fields.

Effect of curing light emission spectrum on the nanohardness and elastic modulus of two bulk-fill resin composites.

Science.gov (United States)

Issa, Yaser; Watts, David C; Boyd, Daniel; Price, Richard B

2016-04-01

To determine the nanohardness and elastic moduli of two bulk-fill resin based composites (RBCs) at increasing depths from the surface and increasing distances laterally from the center after light curing. Two bulk-fill dental RBCs: Tetric EvoCeram Bulk Fill (TECBF) and Filtek Bulk Fill Flowable (FBFF) were light cured in a metal mold with a 6mm diameter and a 10mm long semi-circular notch. The RBCs were photo-polymerized for 10s using a light emitting diode (LED) Bluephase Style curing light, with the original light probe that lacked the homogenizer. This light has two blue light and one violet light LED emitters. By changing the probe orientation over the mold, the light output from only two LEDs reached the RBC. Measurements were made using: (i) the light from one violet and one blue LED, and (ii) the light from the two blue LEDs. Five specimens of each RBC were made using each LED orientation (total 20 specimens). Specimens were then stored in the dark at 37°C for 24h. Fifty indents were made using an Agilent G200 nanoindentor down to 4mm from the surface and 2.5mm right and left of the centerline. The results were analyzed (alpha=0.05) using multiple paired-sample t-tests, ANOVA, Bonferroni post-hoc tests, and Pearson correlations. The elastic modulus and nanohardness varied according to the depth and the distance from the centerline. For TECBF, no significant difference was found between the spatial variations in the elastic modulus or hardness values when violet-blue or blue-blue LEDs were used. For FBFF, the elastic modulus and nanohardness on the side exposed to the violet emitter were significantly less than the side exposed to the blue emitter. A strong correlation between nanohardness and elastic modulus was found in all groups (r(2)=0.9512-0.9712). Resin polymerization was not uniform throughout the RBC. The nanohardness and elastic modulus across two RBC materials were found to decline differently according to the orientation of the violet and blue

Technique for determination of elastic limit of micron band-thick amorphous

International Nuclear Information System (INIS)

Zakharov, E.K.; Pol'dyaeva, G.P.; Tret'yakov, B.N.

1984-01-01

A method is suggested to determine the elastic limit of micron-thick amorphous band under bending. The elastic limit is determined by bending an amorphous band sample around a series of cylindrical mandrels of gradually decreasing radius. Experimental data on measuring the elastic limit of some amorphous iron base alloys according to the suggested technique are presented. The elastic limit of amorphous alloys is shown to lie in the 3140-4110 MPa range depending on chemical composition, which is about 2-2.5 times higher as compared to high-strength crystal alloys

A Stochastic Multiscale Method for the Elastic Wave Equations Arising from Fiber Composites

KAUST Repository

Babuska, Ivo

2016-01-06

We present a stochastic multilevel global-local algorithm [1] for computing elastic waves propagating in fiber-reinforced polymer composites, where the material properties and the size and distribution of fibers in the polymer matrix may be random. The method aims at approximating statistical moments of some given quantities of interest, such as stresses, in regions of relatively small size, e.g. hot spots or zones that are deemed vulnerable to failure. For a fiber-reinforced cross-plied laminate, we introduce three problems: 1) macro; 2) meso; and 3) micro problems, corresponding to the three natural length scales: 1) the sizes of plate; 2) the tickles of plies; and 3) and the diameter of fibers. The algorithm uses a homogenized global solution to construct a local approximation that captures the microscale features of the problem. We perform numerical experiments to show the applicability and efficiency of the method.

Efficient education policy: A second-order elasticity rule

OpenAIRE

Richter, Wolfram F.

2010-01-01

Assuming a two-period model with endogenous choices of labour, education, and saving, efficient education policy is characterized for a Ramsey-like scenario in which the government is constrained to use linear instruments. It is shown that education should be effectively subsidized if, and only if, the elasticity of the earnings function is increasing in education. The strength of second-best subsidization increases in the elasticity of the elasticity of the earnings function. This second-ord...

Effects of elastic resistance exercise on body composition and physical capacity in older women with sarcopenic obesity: A CONSORT-compliant prospective randomized controlled trial.

Science.gov (United States)

Liao, Chun-De; Tsauo, Jau-Yih; Lin, Li-Fong; Huang, Shih-Wei; Ku, Jan-Wen; Chou, Lin-Chuan; Liou, Tsan-Hon

2017-06-01

Sarcopenia is associated with loss of muscle mass and an increased risk of physical disability in elderly people. However, the prevalence of sarcopenia has increased in obese elderly populations. The purpose of this study was to identify the clinical efficacy of elastic resistance exercise training (RET) in patients with sarcopenic obesity. This study was conducted at the rehabilitation center of a university-based teaching hospital and was designed as a prospective and randomized controlled trial with an intention-to-treat analysis. A total of 46 women aged 67.3 (5.2) years were randomly assigned to an experimental group (EG) and control group (CG). The EG underwent elastic RET for 12 weeks, and the CG received no RET intervention. All outcome measures were assessed at the baseline and posttest, including body composition measured using dual-energy X-ray absorptiometry, muscle quality (MQ) defined as a ratio of muscular strength to muscle mass, and physical capacity assessed using functional mobility tests. One-way analysis of covariance and Pearson correlation were used to compare outcomes between the 2 groups and to identify the relationship between changes in body composition and physical outcomes, respectively. A chi-square test was performed to identify differences in qualitative data between the 2 groups. At the posttest, a significant between-group difference was observed in fat-free mass, MQ, and physical capacity (all P exercise exerted benefits on the body composition, MQ, and physical function in patients with sarcopenic obesity. Regular exercise incorporating elastic RET should be used to attenuate muscle mass loss and prevent physical difficulty in obese older adults with sarcopenia on reconditioning therapy. Chinese Clinical Trial Registry, ChiCTR-IPR-15006069.

Computational modeling of elastic properties of carbon nanotube/polymer composites with interphase regions. Part I: Micro-structural characterization and geometric modeling

KAUST Repository

Han, Fei

2014-01-01

A computational strategy to predict the elastic properties of carbon nanotube-reinforced polymer composites is proposed in this two-part paper. In Part I, the micro-structural characteristics of these nano-composites are discerned. These characteristics include networks/agglomerations of carbon nanotubes and thick polymer interphase regions between the nanotubes and the surrounding matrix. An algorithm is presented to construct three-dimensional geometric models with large amounts of randomly dispersed and aggregated nanotubes. The effects of the distribution of the nanotubes and the thickness of the interphase regions on the concentration of the interphase regions are demonstrated with numerical results. © 2013 Elsevier B.V. All rights reserved.

Milk production and chemical composition of milk of Ukrainian mountain Carpathian sheep in pasture period

OpenAIRE

CHOKAN T.

2011-01-01

The comparative analysis of the milk chemical composition depending on milk productivity of Ukrainian Mountain Carpathian sheep during the pasture period were studied. It was found changes of milk composition (increasing of protein content, fat, dry matter and nutritive value) with a decrease of milk yield in the end period of lactation.

A comparative approach to predicting effective dielectric, piezoelectric and elastic properties of PZT/PVDF composites

International Nuclear Information System (INIS)

Ahmad, Zeeshan; Prasad, Ashutosh; Prasad, K.

2009-01-01

The present study addresses the problem of quantitative prediction of effective relative permittivity, dielectric loss factor, piezoelectric charge coefficient, and Young's modulus of PZT/PVDF diphasic ceramic-polymer composite as a function of volume fraction of PZT in the different compositions. Theoretical results for effective relative permittivity derived from several dielectric mixture equations like those of Knott, Rother-Lichtenecker, Bruggeman, Maxwell-Wagner-Webmann-Skipetrov or Dias-Dasgupta, Furukawa, Lewin, Wiener, Jayasundere-Smith, Modified Cule-Torquato, Taylor, Poon-Shin and Rao et al. were fitted to the experimental data taken from previous works of Yamada et al. Similarly, the results for effective piezoelectric coefficient and Young's modulus, derived from different appropriate equations were fitted to the corresponding experimental data taken from the literature. The study revealed that only a few equations like modified Rother-Lichtenecker equation, Dias-Dasgupta equation and Rao equation for dielectric and piezoelectric properties while the four new equations developed in the present study of elastic property (Young's modulus) well fitted the corresponding experimental results. Further, the acceptable data put to various regression analyses showed that in most of the cases the third order polynomial regression analysis provided more acceptable fits.

Introduction to linear elasticity

CERN Document Server

Gould, Phillip L

2013-01-01

Introduction to Linear Elasticity, 3rd Edition, provides an applications-oriented grounding in the tensor-based theory of elasticity for students in mechanical, civil, aeronautical, and biomedical engineering, as well as materials and earth science. The book is distinct from the traditional text aimed at graduate students in solid mechanics by introducing the subject at a level appropriate for advanced undergraduate and beginning graduate students. The author's presentation allows students to apply the basic notions of stress analysis and move on to advanced work in continuum mechanics, plasticity, plate and shell theory, composite materials, viscoelasticity and finite method analysis. This book also:  Emphasizes tensor-based approach while still distilling down to explicit notation Provides introduction to theory of plates, theory of shells, wave propagation, viscoelasticity and plasticity accessible to advanced undergraduate students Appropriate for courses following emerging trend of teaching solid mechan...

How Credible Are Shrinking Wage Elasticities of Married Women Labour Supply?

Directory of Open Access Journals (Sweden)

Duo Qin

2015-12-01

Full Text Available This paper delves into the well-known phenomenon of shrinking wage elasticities for married women in the US over recent decades. The results of a novel model experimental approach via sample data ordering unveil considerable heterogeneity across different wage groups. Yet, surprisingly constant wage elasticity estimates are maintained within certain wage groups over time. In addition to those constant wage elasticity estimates, we find that the composition of working women into different wage groups has changed considerably, resulting in shrinking wage elasticity estimates at the aggregate level. These findings would be impossible to obtain had we not dismantled and discarded the instrumental variable estimation route.

Moduli determination of continuous fiber ceramic composites (CFCCs)

International Nuclear Information System (INIS)

Liaw, P.K.; Hsu, D.K.; Miriyala, N.; Snead, L.L.; McHargue, C.J.

1995-01-01

Nicalon TM /silicon carbide composites were fabricated by the Forced Chemical Vapor Infiltration (FCVI) method. Both through-thickness and in-plane (fiber fabric plane) moduli were determined using ultrasonic techniques. The through-thickness elastic constants (moduli) were found to be much less than the in-plane moduli. Increased porosity significantly decreased both in-plane and through-thickness moduli. A periodic model using a homogenization method was formulated to predict the effect of porosity on the moduli of woven fabric composites. The predicted moduli were found to be in reasonably good agreement with the experimental results. ((orig.))

Wave chaos in the elastic disk.

Science.gov (United States)

Sondergaard, Niels; Tanner, Gregor

2002-12-01

The relation between the elastic wave equation for plane, isotropic bodies and an underlying classical ray dynamics is investigated. We study, in particular, the eigenfrequencies of an elastic disk with free boundaries and their connection to periodic rays inside the circular domain. Even though the problem is separable, wave mixing between the shear and pressure component of the wave field at the boundary leads to an effective stochastic part in the ray dynamics. This introduces phenomena typically associated with classical chaos as, for example, an exponential increase in the number of periodic orbits. Classically, the problem can be decomposed into an integrable part and a simple binary Markov process. Similarly, the wave equation can, in the high-frequency limit, be mapped onto a quantum graph. Implications of this result for the level statistics are discussed. Furthermore, a periodic trace formula is derived from the scattering matrix based on the inside-outside duality between eigenmodes and scattering solutions and periodic orbits are identified by Fourier transforming the spectral density.

A-thermal elastic behavior of silicate glasses.

Science.gov (United States)

Rabia, Mohammed Kamel; Degioanni, Simon; Martinet, Christine; Le Brusq, Jacques; Champagnon, Bernard; Vouagner, Dominique

2016-02-24

Depending on the composition of silicate glasses, their elastic moduli can increase or decrease as function of the temperature. Studying the Brillouin frequency shift of these glasses versus temperature allows the a-thermal composition corresponding to an intermediate glass to be determined. In an intermediate glass, the elastic moduli are independent of the temperature over a large temperature range. For sodium alumino-silicate glasses, the a-thermal composition is close to the albite glass (NaAlSi3O8). The structural origin of this property is studied by in situ high temperature Raman scattering. The structure of the intermediate albite glass and of silica are compared at different temperatures between room temperature and 600 °C. When the temperature increases, it is shown that the high frequency shift of the main band at 440 cm(-1) in silica is a consequence of the cristobalite-like alpha-beta transformation of 6-membered rings. This effect is stronger in silica than bond elongation (anharmonic effects). As a consequence, the elastic moduli of silica increase as the temperature increases. In the albite glass, the substitution of 25% of Si(4+) ions by Al(3+) and Na(+) ions decreases the proportion of SiO2 6-membered rings responsible for the silica anomaly. The effects of the silica anomaly balance the anharmonicity in albite glass and give rise to an intermediate a-thermal glass. Different networks, formers or modifiers, can be added to produce different a-thermal glasses with useful mechanical or chemical properties.

Singularity Structure Analysis of the Higher-Dimensional Time-Gated Manakov System: Periodic Excitations and Elastic Scattering

International Nuclear Information System (INIS)

Kuetche, Victor Kamgang; Bouetou, Thomas Bouetou; Kofane, Timoleon Crepin

2010-12-01

We investigate the singularity structure analysis of the higher-dimensional time-gated Manakov system referring to the (2+1)-dimensional coupled nonlinear Schroedinger (CNLS) equations, and we show that these equations are Painleve-integrable. By means of the Weiss et al.'s methodology, we show the arbitrariness of the expansion coefficients and the consistency of the truncation corresponding to a special Baecklund transformation (BT) of these CNLS equations. In the wake of such transformation, following the Hirota's formalism, we derive a one-soliton solution. Besides, by using the Zakharov-Shabat (ZS) scheme which provides a general Lax-representation of an evolution system, we show that the (2+1)-dimensional CNLS system under interests is completely integrable. Furthermore, using the arbitrariness of the above coefficients, we unearth and investigate a typical spectrum of periodic coherent structures while depicting elastic interactions amongst such patterns. (author)

Topology optimization of periodic microstructures for enhanced dynamic properties of viscoelastic composite materials

DEFF Research Database (Denmark)

Andreassen, Erik; Jensen, Jakob Søndergaard

2014-01-01

We present a topology optimization method for the design of periodic composites with dissipative materials for maximizing the loss/attenuation of propagating waves. The computational model is based on a finite element discretization of the periodic unit cell and a complex eigenvalue problem...... with a prescribed wave frequency. The attenuation in the material is described by its complex wavenumber, and we demonstrate in several examples optimized distributions of a stiff low loss and a soft lossy material in order to maximize the attenuation. In the examples we cover different frequency ranges and relate...... the results to previous studies on composites with high damping and stiffness based on quasi-static conditions for low frequencies and the bandgap phenomenon for high frequencies. Additionally, we consider the issues of stiffness and connectivity constraints and finally present optimized composites...

Free and Forced Vibration of the Moderately Thick Laminated Composite Rectangular Plate on Various Elastic Winkler and Pasternak Foundations

Directory of Open Access Journals (Sweden)

Dongyan Shi

2017-01-01

Full Text Available An improved Fourier series method (IFSM is applied to study the free and forced vibration characteristics of the moderately thick laminated composite rectangular plates on the elastic Winkler or Pasternak foundations which have elastic uniform supports and multipoints supports. The formulation is based on the first-order shear deformation theory (FSDT and combined with artificial virtual spring technology and the plate-foundation interaction by establishing the two-parameter foundation model. Under the framework of this paper, the displacement and rotation functions are expressed as a double Fourier cosine series and two supplementary functions which have no relations to boundary conditions. The Rayleigh-Ritz technique is applied to solve all the series expansion coefficients. The accuracy of the results obtained by the present method is validated by being compared with the results of literatures and Finite Element Method (FEM. In this paper, some results are obtained by analyzing the varying parameters, such as different boundary conditions, the number of layers and points, the spring stiffness parameters, and foundation parameters, which can provide a benchmark for the future research.

An Elastic Plastic Contact Model with Strain Hardening for the LAMMPS Granular Package

Energy Technology Data Exchange (ETDEWEB)

Kuhr, Bryan [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Brake, Matthew Robert [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Component Science and Mechanics; Lechman, Jeremy B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Nanoscale and Reactive Processes

2015-03-01

The following details the implementation of an analytical elastic plastic contact model with strain hardening for normal im pacts into the LAMMPS granular package. The model assumes that, upon impact, the co llision has a period of elastic loading followed by a period of mixed elastic plas tic loading, with contributions to each mechanism estimated by a hyperbolic seca nt weight function. This function is implemented in the LAMMPS source code as the pair style gran/ep/history. Preliminary tests, simulating the pouring of pure nickel spheres, showed the elastic/plastic model took 1.66x as long as similar runs using gran/hertz/history.

Simple and cost-effective method of highly conductive and elastic carbon nanotube/polydimethylsiloxane composite for wearable electronics.

Science.gov (United States)

Kim, Jeong Hun; Hwang, Ji-Young; Hwang, Ha Ryeon; Kim, Han Seop; Lee, Joong Hoon; Seo, Jae-Won; Shin, Ueon Sang; Lee, Sang-Hoon

2018-01-22

The development of various flexible and stretchable materials has attracted interest for promising applications in biomedical engineering and electronics industries. This interest in wearable electronics, stretchable circuits, and flexible displays has created a demand for stable, easily manufactured, and cheap materials. However, the construction of flexible and elastic electronics, on which commercial electronic components can be mounted through simple and cost-effective processing, remains challenging. We have developed a nanocomposite of carbon nanotubes (CNTs) and polydimethylsiloxane (PDMS) elastomer. To achieve uniform distributions of CNTs within the polymer, an optimized dispersion process was developed using isopropyl alcohol (IPA) and methyl-terminated PDMS in combination with ultrasonication. After vaporizing the IPA, various shapes and sizes can be easily created with the nanocomposite, depending on the mold. The material provides high flexibility, elasticity, and electrical conductivity without requiring a sandwich structure. It is also biocompatible and mechanically stable, as demonstrated by cytotoxicity assays and cyclic strain tests (over 10,000 times). We demonstrate the potential for the healthcare field through strain sensor, flexible electric circuits, and biopotential measurements such as EEG, ECG, and EMG. This simple and cost-effective fabrication method for CNT/PDMS composites provides a promising process and material for various applications of wearable electronics.

Effective medium of periodic fluid-solid composites

KAUST Repository

Mei, Jun

2012-05-24

An analytic solution of the effective mass density and bulk modulus of a periodic fluid-solid composite is obtained by using the multiple-scattering theory in the long-wavelength limit. It is shown that when the concentration of solid inclusions is high, the effective mass density is structure dependent and differs significantly from the leading-order dipole solution, whereas Wood\\'s formula is accurately valid, independently of the structures. Numerical evaluations from the analytic solution are shown to be in excellent agreement with finite-element simulations. In the vicinity of the tight-packing limit, the critical behavior of the effective mass density is also studied and it is independent of the lattice symmetry. © 2012 Europhysics Letters Association.

Class I and Class II restorations of resin composite: an FE analysis of the influence of modulus of elasticity on stresses generated by occlusal loading

DEFF Research Database (Denmark)

Asmussen, Erik; Peutzfeldt, Anne

2008-01-01

the restoration was left nonbonded. The resin composite was modelled with a modulus of elasticity of 5, 10, 15 or 20 GPa and loaded occlusally with 100 N. By means of the soft-ware program ABAQUS the von Mises stresses in enamel and dentin were calculated. RESULTS: In the bonded scenario, the maximum stresses...

Ridge regression for predicting elastic moduli and hardness of calcium aluminosilicate glasses

Science.gov (United States)

Deng, Yifan; Zeng, Huidan; Jiang, Yejia; Chen, Guorong; Chen, Jianding; Sun, Luyi

2018-03-01

It is of great significance to design glasses with satisfactory mechanical properties predictively through modeling. Among various modeling methods, data-driven modeling is such a reliable approach that can dramatically shorten research duration, cut research cost and accelerate the development of glass materials. In this work, the ridge regression (RR) analysis was used to construct regression models for predicting the compositional dependence of CaO-Al2O3-SiO2 glass elastic moduli (Shear, Bulk, and Young’s moduli) and hardness based on the ternary diagram of the compositions. The property prediction over a large glass composition space was accomplished with known experimental data of various compositions in the literature, and the simulated results are in good agreement with the measured ones. This regression model can serve as a facile and effective tool for studying the relationship between the compositions and the property, enabling high-efficient design of glasses to meet the requirements for specific elasticity and hardness.

Glycerine Treated Nanofibrillated Cellulose Composites

Directory of Open Access Journals (Sweden)

Esra Erbas Kiziltas

2016-01-01

Full Text Available Glycerine treated nanofibrillated cellulose (GNFC was prepared by mixing aqueous nanofibrillated cellulose (NFC suspensions with glycerine. Styrene maleic anhydride (SMA copolymer composites with different loadings of GNFC were prepared by melt compounding followed by injection molding. The incorporation of GNFC increased tensile and flexural modulus of elasticity of the composites. Thermogravimetric analysis showed that as GNFC loading increased, the thermal stability of the composites decreased marginally. The incorporation of GNFC into the SMA copolymer matrix resulted in higher elastic modulus (G′ and shear viscosities than the neat SMA copolymer, especially at low frequencies. The orientation of rigid GNFC particles in the composites induced a strong shear thinning behavior with an increase in GNFC loading. The decrease in the slope of elastic modulus with increasing GNFC loading suggested that the microstructural changes of the polymer matrix can be attributed to the incorporation of GNFC. Scanning electron microscopy (SEM images of fracture surfaces show areas of GNFC agglomerates in the SMA matrix.

Effect of elasticity on stress distribution in CAD/CAM dental crowns: Glass ceramic vs. polymer-matrix composite.

Science.gov (United States)

Duan, Yuanyuan; Griggs, Jason A

2015-06-01

Further investigations are required to evaluate the mechanical behaviour of newly developed polymer-matrix composite (PMC) blocks for computer-aided design/computer-aided manufacturing (CAD/CAM) applications. The purpose of this study was to investigate the effect of elasticity on the stress distribution in dental crowns made of glass-ceramic and PMC materials using finite element (FE) analysis. Elastic constants of two materials were determined by ultrasonic pulse velocity using an acoustic thickness gauge. Three-dimensional solid models of a full-coverage dental crown on a first mandibular molar were generated based on X-ray micro-CT scanning images. A variety of load case-material property combinations were simulated and conducted using FE analysis. The first principal stress distribution in the crown and luting agent was plotted and analyzed. The glass-ceramic crown had stress concentrations on the occlusal surface surrounding the area of loading and the cemented surface underneath the area of loading, while the PMC crown had only stress concentration on the occlusal surface. The PMC crown had lower maximum stress than the glass-ceramic crown in all load cases, but this difference was not substantial when the loading had a lateral component. Eccentric loading did not substantially increase the maximum stress in the prosthesis. Both materials are resistant to fracture with physiological occlusal load. The PMC crown had lower maximum stress than the glass-ceramic crown, but the effect of a lateral loading component was more pronounced for a PMC crown than for a glass-ceramic crown. Knowledge of the stress distribution in dental crowns with low modulus of elasticity will aid clinicians in planning treatments that include such restorations. Copyright © 2015 Elsevier Ltd. All rights reserved.

Ab initio study of single-crystalline and polycrystalline elastic properties of Mg-substituted calcite crystals.

Science.gov (United States)

Zhu, L-F; Friák, M; Lymperakis, L; Titrian, H; Aydin, U; Janus, A M; Fabritius, H-O; Ziegler, A; Nikolov, S; Hemzalová, P; Raabe, D; Neugebauer, J

2013-04-01

We employ ab initio calculations and investigate the single-crystalline elastic properties of (Ca,Mg)CO3 crystals covering the whole range of concentrations from pure calcite CaCO3 to pure magnesite MgCO3. Studying different distributions of Ca and Mg atoms within 30-atom supercells, our theoretical results show that the energetically most favorable configurations are characterized by elastic constants that nearly monotonously increase with the Mg content. Based on the first principles-derived single-crystalline elastic anisotropy, the integral elastic response of (Ca,Mg)CO3 polycrystals is determined employing a mean-field self-consistent homogenization method. As in case of single-crystalline elastic properties, the computed polycrystalline elastic parameters sensitively depend on the chemical composition and show a significant stiffening impact of Mg atoms on calcite crystals in agreement with the experimental findings. Our analysis also shows that it is not advantageous to use a higher-scale two-phase mix of stoichiometric calcite and magnesite instead of substituting Ca atoms by Mg ones on the atomic scale. Such two-phase composites are not significantly thermodynamically favorable and do not provide any strong additional stiffening effect. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effect of PbO on the elastic behavior of ZnO–P2O5 glass systems

Directory of Open Access Journals (Sweden)

H.A.A. Sidek

Full Text Available A series of ternary phosphate glasses in the form of 40(P2O5–(60 − xZnO–xPbO and 50(P2O5–(50 − xZnO–xPbO where x = 0–60 mol%, have been successfully prepared by conventional melt quenching technique. Both longitudinal and shear ultrasonic velocities were measured in different compositions of PbO using the MBS8000 ultrasonic data acquisition system at 10 MHz frequency and at room temperature. The ultrasonic velocity data, the density and the calculated elastic moduli are found to be composition dependent and discussed in terms of PbO modifiers. The correlation of elastic moduli with the atomic packing density of these glasses was discussed. To predict the compositional dependence of elastic moduli of this glass system, the interpretation of the variation in the experimental elastic behavior observed has been studied based on various of the bond compression and the Makishima–Mackenzie models. Keywords: Elastic moduli, Glasses, Zinc phosphate, Bond compression, Makishima–Mackenzie models

On some periodicity effects

DEFF Research Database (Denmark)

Sorokin, Sergey V.

2015-01-01

The talk is concerned with the modelling of wave propagation in and vibration of periodic elastic structures. Although analysis of wave-guide properties of infinite periodic structures is a well establish research subject, some issues have not yet been fully addressed in the literature. The aim o...

Finite Element Study on Performance of Piezoelectric Bimorph Cantilevers Using Porous/Ceramic 0-3 Polymer Composites

Science.gov (United States)

Kiran, Raj; Kumar, Anuruddh; Chauhan, Vishal S.; Kumar, Rajeev; Vaish, Rahul

2018-01-01

Finite element analysis of 0-3 composites made of piezoceramic particles and pores embedded in polyvinylidene difluoride (PVDF) has been carried out. The representative volume element (RVE) approach was used to calculate the effective elastic and piezoelectric properties of the periodic isotropic 0-3 piezoelectric composites. It was observed that the elastic and piezoelectric properties increased with the volume fraction of {K}_{0.475} {Na}_{0.475} {Li}_{0.05} ( {{Nb}_{0.92} {Ta}_{0.05} {Sb}_{0.03} } ){O}3 (KNLNTS) particles but decreased for the porous composites. These effective properties were further used to analyze the potential use of such bimorph cantilever beams in sensing and energy harvesting applications. Sensing voltage continuously increased for KNLNTS filled composites while for porous materials it increased up to 15% volume fraction porosity and then decreased. The same trend was also observed for the power produced by the harvester. However, the sensing voltage and power produced by harvesters made of porous composites were lower than for harvesters made of pure PVDF.

Elastic properties of amorphous boron suboxide based solids studied using ab initio molecular dynamics

International Nuclear Information System (INIS)

Music, Denis; Schneider, Jochen M

2008-01-01

We have studied the correlation between chemical composition, structure, chemical bonding and elastic properties of amorphous B 6 O based solids using ab initio molecular dynamics. These solids are of different chemical compositions, but the elasticity data appear to be a function of density. This is in agreement with previous experimental observations. As the density increases from 1.64 to 2.38 g cm -3 , the elastic modulus increases from 74 to 253 GPa. This may be understood by analyzing the cohesive energy and the chemical bonding of these compounds. The cohesive energy decreases from -7.051 to -7.584 eV/atom in the elastic modulus range studied. On the basis of the electron density distributions, Mulliken analysis and radial distribution functions, icosahedral bonding is the dominating bonding type. C and N promote cross-linking of icosahedra and thus increase the density, while H hinders the cross-linking by forming OH groups. The presence of icosahedral bonding is independent of the density

Steady shear characteristic and behavior of magneto-thermo-elasticity of isotropic MR elastomers

International Nuclear Information System (INIS)

Gao, Wei; Wang, Xingzhe

2016-01-01

The magneto-thermo-elastic steady shear behaviors of isotropic smart composites of silicon rubber matrix randomly filled with ferromagnetic particles, commonly referred to as magnetorheological (MR) elastomers, are investigated experimentally and theoretically in the present study. The strip specimens of the MR elastomer composite with different ferromagnetic particle concentrations are fabricated and implemented for lap-shear tests under both magnetic and thermal fields. It is illustrated that the magneto-thermo-elastic shear modulus of the MR elastomer is markedly enhanced with the volume fraction of ferromagnetic particles and the applied external magnetic field, while the shear modulus is decreased with the environment temperature. To qualitatively elucidate the magneto-thermo-elastic shear performance of this kind of magnetic smart composites, a modified constitutive of hyperelasticity is suggested taking into account the influence of magnetic field and temperature on the magnetic potential energy and strain energy. The theoretical modeling predictions on the stress–strain behaviors for different applied magnetic fields and environment temperatures are compared to experimental observations to demonstrate a good agreement. (paper)

Elastic-resilience-induced dispersion of carbon nanotubes: a novel way of fabricating high performance elastomer

International Nuclear Information System (INIS)

Wu, Siwu; Lin, Tengfei; Guo, Baochun

2013-01-01

State-of-the-art processes cannot achieve rubber/multi-walled carbon nanotube (MWCNT) composites with satisfactory performance by using pristine MWCNTs and conventional processing equipment. In this work, high performance rubber/MWCNT composites featuring a combination of good mechanical properties, electrical and thermal conductivities and damping capacity over a wide temperature range are fabricated based on a well-developed master batch process. It is demonstrated that the MWCNTs are dispersed homogeneously due to the disentanglement induced by well-wetting and shearing, and the elastic-resilience-induced dispersion of the MWCNTs by rubber chains via the novel processing method. To further enhance the efficacy of elastic-resilience-induced dispersion for MWCNTs, a slightly pre-crosslinked network is constructed in the master batch. Consequently, we obtain rubber/MWCNT composites with unprecedented performance by amplifying the reinforcing effect of relatively low MWCNT loading. This work provides a novel insight into the fabrication of high performance functional elastomeric composites with pristine CNTs by taking advantage of the unique elastic resilience of rubber chains as the driving force for the disentanglement of CNTs. (paper)

Optimal Electricity Charge Strategy Based on Price Elasticity of Demand for Users

Science.gov (United States)

Li, Xin; Xu, Daidai; Zang, Chuanzhi

The price elasticity is very important for the prediction of electricity demand. This paper mainly establishes the price elasticity coefficient for electricity in single period and inter-temporal. Then, a charging strategy is established based on these coefficients. To evaluate the strategy proposed, simulations of the two elastic coefficients are carried out based on the history data of a certain region.

Density functional calculations of elastic properties of portlandite, Ca(OH)(2)

DEFF Research Database (Denmark)

Laugesen, Jakob Lund

2005-01-01

The elastic constants of portlandite, Ca(OH)(2), are calculated by use of density functional theory. A lattice optimization of an infinite (periodic boundary conditions) lattice is performed on which strains are applied. The elastic constants are extracted by minimizing Hooke's law of linear...

Elasticity and physico-chemical properties during drinking water biofilm formation.

Science.gov (United States)

Abe, Yumiko; Polyakov, Pavel; Skali-Lami, Salaheddine; Francius, Grégory

2011-08-01

Atomic force microscope techniques and multi-staining fluorescence microscopy were employed to study the steps in drinking water biofilm formation. During the formation of a conditioning layer, surface hydrophobic forces increased and the range of characteristic hydrophobic forces diversified with time, becoming progressively complex in macromolecular composition, which in return triggered irreversible cellular adhesion. AFM visualization of 1 to 8 week drinking water biofilms showed a spatially discontinuous and heterogeneous distribution comprising an extensive network of filamentous fungi in which biofilm aggregates were embedded. The elastic modulus of 40-day-old biofilms ranged from 200 to 9000 kPa, and the biofilm deposits with a height >0.5 μm had an elastic modulus water biofilms were composed of a soft top layer and a basal layer with significantly higher elastic modulus values falling in the range of fungal elasticity.

Examining the short-run price elasticity of gasoline demand in the United States

Science.gov (United States)

Brannan, Michael James

Estimating the consumer demand response to changes in the price of gasoline has important implications regarding fuel tax policies and environmental concerns. There are reasons to believe that the short-run price elasticity of gasoline demand fluctuates due to changing structural and behavioral factors. In this paper I estimate the short-run price elasticity of gasoline demand in two time periods, from 2001 to 2006 and from 2007 to 2010. This study utilizes data at both the national and state levels to produce estimates. The short-run price elasticities range from -0.034 to -0.047 during 2001 to 2006, compared to -0.058 to -0.077 in the 2007 to 2010 period. This paper also examines whether there are regional differences in the short-run price elasticity of gasoline demand in the United States. However, there appears to only be modest variation in price elasticity values across regions.

Low-temperature monocrystal elastic constants of Fe-19Cr-10Ni

International Nuclear Information System (INIS)

Ledbetter, H.M.

1984-01-01

By a pulse-echo-overlap ultrasonic method, we determined the monocrystal elastic constants (C 11 , C 12 , C 44 ) of an Fe-19Cr-10Ni alloy between 295 and 4 K. In composition this laboratory alloy approximates a technological austenitic stainless steel: AISI 304. Many previous studies on polycrystalline steels found a low-temperature magnetic phase transition that affects physical properties, including elastic constants. At the transition, anomalies occur in all polycrystal elastic constants: Young's modulus, shear modulus, bulk modulus, and Poisson's ratio. The present study found that the transition, near 50 K, does not affect one monocrystal elastic constant: C 44 , the resistance to shear on a (100) plane in a [100]-type direction. We interpret this new observation from the viewpoint of a Born-type lattice model. Also, we comment about the relationship between the elastic-constant changes and the low-temperature magnetic state

Growth hormone deficiency in the transition period: body composition and gonad function.

Science.gov (United States)

Balercia, G; Giovannini, L; Paggi, F; Spaziani, M; Tahani, N; Boscaro, M; Lenzi, A; Radicioni, A

2011-10-01

Recombinant GH therapy is normally administered to GH-deficient children in order to achieve a satisfactory height - the main target during childhood and adolescence. However, the role of GH does not end once final height has been reached, but continues during the so-called transition period. In this phase of life, the body undergoes several changes, both physical and psychological, that culminate in adulthood. During this period, GH has a part in numerous metabolic functions. These include the lipid profile, where it increases HDL and reduces LDL, with the global effect of cardiovascular protection. It also has important effects on body composition (improved muscle strength and lean body mass and reduced body fat), the achievement of proper peak bone density, and gonad maturation. Retesting during the transition period, involving measurement of IGF-I plus a provocative test (insulin tolerance test or GHRH + arginine test), is thus necessary to establish any persistent GH deficiency requiring additional replacement therapy. The close cooperation of the medical professionals involved in the patient's transition from a pediatric to an adult endocrinologist is essential. The aim of this review is to point out the main aspects of GH treatment on body composition, metabolic and gonad functions in the transition period.

Consumer brand choice: individual and group analyses of demand elasticity.

Science.gov (United States)

Oliveira-Castro, Jorge M; Foxall, Gordon R; Schrezenmaier, Teresa C

2006-03-01

Following the behavior-analytic tradition of analyzing individual behavior, the present research investigated demand elasticity of individual consumers purchasing supermarket products, and compared individual and group analyses of elasticity. Panel data from 80 UK consumers purchasing 9 product categories (i.e., baked beans, biscuits, breakfast cereals, butter, cheese, fruit juice, instant coffee, margarine and tea) during a 16-week period were used. Elasticity coefficients were calculated for individual consumers with data from all or only 1 product category (intra-consumer elasticities), and for each product category using all data points from all consumers (overall product elasticity) or 1 average data point per consumer (interconsumer elasticity). In addition to this, split-sample elasticity coefficients were obtained for each individual with data from all product categories purchased during weeks 1 to 8 and 9 to 16. The results suggest that: 1) demand elasticity coefficients calculated for individual consumers purchasing supermarket food products are compatible with predictions from economic theory and behavioral economics; 2) overall product elasticities, typically employed in marketing and econometric research, include effects of interconsumer and intraconsumer elasticities; 3) when comparing demand elasticities of different product categories, group and individual analyses yield similar trends; and 4) individual differences in demand elasticity are relatively consistent across time, but do not seem to be consistent across products. These results demonstrate the theoretical, methodological, and managerial relevance of investigating the behavior of individual consumers.

Population and energy elasticity of tornado casualties

Science.gov (United States)

Fricker, Tyler; Elsner, James B.; Jagger, Thomas H.

2017-04-01

Tornadoes are capable of catastrophic destruction and mass casualties, but there are yet no estimates of how sensitive the number of casualties are to changes in the number of people in harm's way or to changes in tornado energy. Here the relationship between tornado casualties (deaths and injuries), population, and energy dissipation is quantified using the economic concept of "elasticity." Records of casualties from individual tornadoes over the period 2007-2015 are fit to a regression model. The coefficient on the population term (population elasticity) indicates that a doubling in population increases the casualty rate by 21% [(17, 24)%, 95% credible interval]. The coefficient on the energy term (energy elasticity) indicates that a doubling in energy dissipation leads to a 33% [(30, 35)%, 95% credible interval] increase in the casualty rate. The difference in elasticity values show that on average, changes in energy dissipation have been relatively more important in explaining tornado casualties than changes in population. Assuming no changes in warning effectiveness or mitigation efforts, these elasticity estimates can be used to project changes in casualties given the known population trends and possible trends in tornado activity.

Stress fields and energy of disclination-type defects in zones of localized elastic distortions

Science.gov (United States)

Sukhanov, Ivan I.; Tyumentsev, Alexander N.; Ditenberg, Ivan A.

2016-11-01

This paper studies theoretically the elastically deformed state and analyzes deformation mechanisms in nanocrystals in the zones of localized elastic distortions and related disclination-type defects, such as dipole, quadrupole and multipole of partial disclinations. Significant differences in the energies of quadrupole and multipole configurations in comparison with nanodipole are revealed. The mechanism of deformation localization in the field of elastic distortions is proposed, which is a quasi-periodic sequence of formation and relaxation of various disclination ensembles with a periodic change in the energy of the defect.

A rational approach to estimating the surgical demand elasticity needed to guide manpower reallocation during contagious outbreaks.

Science.gov (United States)

Tsao, Hsiao-Mei; Sun, Ying-Chou; Liou, Der-Ming

2015-01-01

Emerging infectious diseases continue to pose serious threats to global public health. So far, however, few published study has addressed the need for manpower reallocation needed in hospitals when such a serious contagious outbreak occurs. To quantify the demand elasticity of the major surgery types in order to guide future manpower reallocation during contagious outbreaks. Based on a nationwide research database in Taiwan, we extracted the monthly volumes of major surgery types for the period 1998-2003, which covered the SARS period, in order to carry out a time series analysis. The demand elasticity of each surgery type was then estimated by autoregressive integrated moving average (ARIMA) analysis. During the study period, the surgical volumes of most selected surgery types either increased or remained steady. We categorized these surgery types into low-, moderate- and high-elastic groups according to their demand elasticity. Appendectomy, 'open reduction of fracture with internal fixation' and 'free skin graft' were in the low demand elasticity group. Transurethral prostatectomy and extracorporeal shockwave lithotripsy (ESWL) were in the high demand elasticity group. The manpower of the departments carrying out the surgeries with low demand elasticity should be maintained during outbreaks. In contrast, departments in charge of surgeries mainly with high demand elasticity, like urology departments, may be in a position to have part of their staff reallocated. Taking advantage of the demand variation during the SARS period in 2003, we adopted the concept of demand elasticity and used a time series approach to figure out an effective index of demand elasticity for various types of surgery that could be used as a rational reference to carry out manpower reallocation during contagious outbreak situations.

On characterizing the mechanical properties of aluminum–alumina composites

International Nuclear Information System (INIS)

Gudlur, Pradeep; Boczek, Artur; Radovic, Miladin; Muliana, Anastasia

2014-01-01

The overall response of aluminum–alumina (Al–Al 2 O 3 ) composites depends strongly on their microstructural characteristics. We study the overall mechanical response of Al–Al 2 O 3 composites experimentally, using Resonant Ultrasound Spectroscopy (RUS) and uniaxial compressive testing. Microstructures of composite with 10% alumina volume content are constructed from the microstructural images of the composite obtained from scanning electron microscopy (SEM). The SEM images of the composite are converted to finite element (FE) meshes, which are used to solve the boundary value problem in order to determine the overall mechanical response of the Al–Al 2 O 3 composite. The responses generated from the micromechanical models are compared with the elastic modulus obtained from RUS and experimental stress–strain curves from uniaxial compression tests. Effects of processing, porosity, alumina content, thermal (residual) stress, and plastic deformation on the overall elastic modulus and response of the composites are also studied. We observed that slightly altering the processing method had a significant effect on the microstructural characteristics and in turn on the overall physical and mechanical properties of the composite. With changes in porosity by 2–3%, the elastic modulus was found to vary by 10–15 GPa approximately. We observed that the elastic moduli of the composites determined from the uniaxial compressive tests are close to those obtained from RUS

Visco-piezo-elastic parameter estimation in laminated plate structures

DEFF Research Database (Denmark)

Araujo, A. L.; Mota Soares, C. M.; Herskovits, J.

2009-01-01

A parameter estimation technique is presented in this article, for identification of elastic, piezoelectric and viscoelastic properties of active laminated composite plates with surface-bonded piezoelectric patches. The inverse method presented uses experimental data in the form of a set of measu...

Response of multiferroic composites inferred from a fast-Fourier-transform-based numerical scheme

International Nuclear Information System (INIS)

Brenner, Renald; Bravo-Castillero, Julián

2010-01-01

The effective response and the local fields within periodic magneto-electric multiferroic composites are investigated by means of a numerical scheme based on fast Fourier transforms. This computational framework relies on the iterative resolution of coupled series expansions for the magnetic, electric and strain fields. By using an augmented Lagrangian formulation, a simple and robust procedure which makes use of the uncoupled Green operators for the elastic, electrostatics and magnetostatics problems is proposed. Its accuracy is assessed in the cases of laminated and fibrous two-phase composites for which analytical solutions exist

Elasticity and Density of Paleozoic Shales from Bornholm

DEFF Research Database (Denmark)

Fabricius, Ida Lykke; Haugwitz, C.; Larsen, Pernille Birkelund

2017-01-01

Darcy. We found that solid density and elastic stiffness parameters only vary insignificantly with solid composition, when TOC is lower than 5%, but that mass density and TOC are correlated when TOC is higher than 5%. A similar correlation was not seen for TOC and Sonic logging data. A reason can...

Nonlocal elasticity tensors in dislocation and disclination cores

International Nuclear Information System (INIS)

Taupin, V.; Gbemou, K.; Fressengeas, C.; Capolungo, L.

2017-01-01

We introduced nonlocal elastic constitutive laws for crystals containing defects such as dislocations and disclinations. Additionally, the pointwise elastic moduli tensors adequately reflect the elastic response of defect-free regions by relating stresses to strains and couple-stresses to curvatures, elastic cross-moduli tensors relating strains to couple-stresses and curvatures to stresses within convolution integrals are derived from a nonlocal analysis of strains and curvatures in the defects cores. Sufficient conditions are derived for positive-definiteness of the resulting free energy, and stability of elastic solutions is ensured. The elastic stress/couple stress fields associated with prescribed dislocation/disclination density distributions and solving the momentum and moment of momentum balance equations in periodic media are determined by using a Fast Fourier Transform spectral method. Here, the convoluted cross-moduli bring the following results: (i) Nonlocal stresses and couple stresses oppose their local counterparts in the defects core regions, playing the role of restoring forces and possibly ensuring spatio-temporal stability of the simulated defects, (ii) The couple stress fields are strongly affected by nonlocality. Such effects favor the stability of the simulated grain boundaries and allow investigating their elastic interactions with extrinsic defects, (iii) Driving forces inducing grain growth or refinement derive from the self-stress and couple stress fields of grain boundaries in nanocrystalline configurations.

Micromechanical analysis of a hybrid composite—effect of boron carbide particles on the elastic properties of basalt fiber reinforced polymer composite

Science.gov (United States)

Krishna Golla, Sai; Prasanthi, P.

2016-11-01

A fiber reinforced polymer (FRP) composite is an important material for structural application. The diversified application of FRP composites has become the center of attention for interdisciplinary research. However, improvements in the mechanical properties of this class of materials are still under research for different applications. The reinforcement of inorganic particles in a composite improves its structural properties due to their high stiffness. The present research work is focused on the prediction of the mechanical properties of the hybrid composites where continuous fibers are reinforced in a micro boron carbide particle mixed polypropylene matrix. The effectiveness of the addition of 30 wt. % of boron carbide (B4C) particle contributions regarding the longitudinal and transverse properties of the basalt fiber reinforced polymer composite at various fiber volume fractions is examined by finite element analysis (FEA). The experimental approach is the best way to determine the properties of the composite but it is expensive and time-consuming. Therefore, the finite element method (FEM) and analytical methods are the viable methods for the determination of the composite properties. The FEM results were obtained by adopting a micromechanics approach with the support of FEM. Assuming a uniform distribution of reinforcement and considering one unit-cell of the whole array, the properties of the composite materials are determined. The predicted elastic properties from FEA are compared with the analytical results. The results suggest that B4C particles are a good reinforcement for the enhancement of the transverse properties of basalt fiber reinforced polypropylene.

Load partitioning in Ai203-Al composites with three- dimensional periodic architecture

International Nuclear Information System (INIS)

Young, M.L.; Rao, R.; Almer, J.D.; Haeffner, D.R.; Lewis, J.A.; Dunand, D.C.

2009-01-01

Interpenetrating composites are created by infiltration of liquid aluminum into three-dimensional (3-D) periodic Al 2 O 3 preforms with simple tetragonal symmetry produced by direct-write assembly. Volume-averaged lattice strains in the Al 2 O 3 phase of the composite are measured by synchrotron X-ray diffraction for various uniaxial compression stresses up to -350MPa. Load transfer, found by diffraction to occur from the metal phase to the ceramic phase, is in general agreement with simple rule-of-mixture models and in better agreement with more complex, 3-D finite-element models that account for metal plasticity and details of the geometry of both phases. Spatially resolved diffraction measurements show variations in load transfer at two different positions within the composite.

Nanomechanical properties of dental resin-composites.

Science.gov (United States)

El-Safty, S; Akhtar, R; Silikas, N; Watts, D C

2012-12-01

To determine by nanoindentation the hardness and elastic modulus of resin-composites, including a series with systematically varied filler loading, plus other representative materials that fall into the categories of flowable, bulk-fill and conventional nano-hybrid types. Ten dental resin-composites: three flowable, three bulk-fill and four conventional were investigated using nanoindentation. Disc specimens (15mm×2mm) were prepared from each material using a metallic mold. Specimens were irradiated in the mold at top and bottom surfaces in multiple overlapping points (40s each) with light curing unit at 650mW/cm(2). Specimens were then mounted in 3cm diameter phenolic ring forms and embedded in a self-curing polystyrene resin. After grinding and polishing, specimens were stored in distilled water at 37°C for 7 days. Specimens were investigated using an Agilent Technologies XP nanoindenter equipped with a Berkovich diamond tip (100nm radius). Each specimen was loaded at one loading rate and three different unloading rates (at room temperature) with thirty indentations, per unloading rate. The maximum load applied by the nanoindenter to examine the specimens was 10mN. Dependent on the type of the resin-composite material, the mean values ranged from 0.73GPa to 1.60GPa for nanohardness and from 14.44GPa to 24.07GPa for elastic modulus. There was a significant positive non-linear correlation between elastic modulus and nanohardness (r(2)=0.88). Nonlinear regression revealed a significant positive correlation (r(2)=0.62) between elastic moduli and filler loading and a non-significant correlation (r(2)=0.50) between nanohardness and filler loading of the studied materials. Varying the unloading rates showed no consistent effect on the elastic modulus and nanohardness of the studied materials. For a specific resin matrix, both elastic moduli and nanohardness correlated positively with filler loading. For the resin-composites investigated, the group-average elastic

Mechanical Behaviour of 3D Multi-layer Braided Composites: Experimental, Numerical and Theoretical Study

Science.gov (United States)

Deng, Jian; Zhou, Guangming; Ji, Le; Wang, Xiaopei

2017-12-01

Mechanical properties and failure mechanisms of a newly designed 3D multi-layer braided composites are evaluated by experimental, numerical and theoretical studies. The microstructure of the composites is introduced. The unit cell technique is employed to address the periodic arrangement of the structure. The volume averaging method is used in theoretical solutions while FEM with reasonable periodic boundary conditions and meshing technique in numerical simulations. Experimental studies are also conducted to verify the feasibility of the proposed models. Predicted elastic properties agree well with the experimental data, indicating the feasibility of the proposed models. Numerical evaluation is more accurate than theoretical assessment. Deformations and stress distributions of the unit cell under tension shows displacement and traction continuity, guaranteeing the rationality of the applied periodic boundary conditions. Although compression and tension modulus are close, the compressive strength only reaches 70% of the tension strength. This indicates that the composites can be weakened in compressive loading. Additionally, by analysing the micrograph of fracture faces and strain-stress curves, a brittle failure mechanism is observed both in composites under tension and compression.

Elastic interaction energies of defect structures

International Nuclear Information System (INIS)

Seitz, E.; de Fontaine, D.

1976-01-01

The elastic strain energy between point defects and small disk-shaped clusters of defects are calculated to determine stable configurations. A distortion tensor of tetragonal symmetry is assigned to each impurity atom. The tetragonality ratio t is varied to cover needle-type (t greater than 1), spherical (t = 1) and disk-type (t less than 0) strain fields. To vary the elastic properties of the host material, Fe, Cu, Al, and V were chosen as examples. Computer calculations are based on the microscopic theory of elasticity which emphasizes calculations in discrete Fourier space. Pairs of point defects order along [001] for t less than 1 and along (001) for t = 1 for all host elements. For t greater than 1 fcc lattices and bcc lattices behave differently. It is shown that only certain three dimensional periodic arrangements of parallel and perpendicular disk-like defect clusters are realized for given tetragonality ratio t and host element

Computational Elastic Knots

KAUST Repository

Zhao, Xin

2013-05-01

Elastic rods have been studied intensively since the 18th century. Even now the theory of elastic rods is still developing and enjoying popularity in computer graphics and physical-based simulation. Elastic rods also draw attention from architects. Architectural structures, NODUS, were constructed by elastic rods as a new method of form-finding. We study discrete models of elastic rods and NODUS structures. We also develop computational tools to find the equilibria of elastic rods and the shape of NODUS. Applications of elastic rods in forming torus knot and closing Bishop frame are included in this thesis.

Bulk microstructure and local elastic properties of carbon nanocomposites studied by impulse acoustic microscopy technique

Science.gov (United States)

Levin, V.; Petronyuk, Yu.; Morokov, E.; Chernozatonskii, L.; Kuzhir, P.; Fierro, V.; Celzard, A.; Bellucci, S.; Bistarelli, S.; Mastrucci, M.; Tabacchioni, I.

2016-05-01

Bulk microstructure and elastic properties of epoxy-nanocarbon nanocomposites for diverse types and different content of carbon nanofiller has been studied by using impulse acoustic microscopy technique. It has been shown occurrence of various types of mesoscopic structure formed by nanoparticles inside the bulk of nanocomposite materials, including nanoparticle conglomerates and nanoparticle aerogel systems. In spite of the bulk microstructure, nanocarbon composites demonstrate elastic uniformity and negligible influence of nanofiller on elastic properties of carbon nanocomposite materials.

Functional Elastic Knits Made of Bamboo Charcoal and Quick-Dry Yarns: Manufacturing Techniques and Property Evaluations

Directory of Open Access Journals (Sweden)

Jia-Horng Lin

2017-12-01

Full Text Available Conventional sportswear fabrics are functional textiles that can mitigate the impaired muscles caused by exercises for the wearers, but they can also cause discomfort and skin allergy. This study proposes combining two yarns to form functional composite yarns, by using a twisting or wrapping process. Moreover, a different twist number is used in order to adjust the performance of functional composite yarns. A crochet machine is used to make the functional composite yarns into functional elastic knits that are suitable for use in sportswear. The test results show that, in comparison to the non-processed yarns, using the twisted or wrapped yarns can considerably decrease the water vapor transmission rate of functional elastic knits by 38%, while also improving their far infrared emissivity by 13%, water absorption rate by 39%, and air permeability by 136%. In particular, the functional elastic knits that are made of B-wrapped yarns (bamboo charcoal- wrapped yarns, composed of 20 twists per inch, have the optimal diverse functions.

Interface effects on effective elastic moduli of nanocrystalline materials

International Nuclear Information System (INIS)

Wang Gangfeng; Feng Xiqiao; Yu Shouwen; Nan Cewen

2003-01-01

Interfaces often play a significant role in many physical properties and phenomena of nanocrystalline materials (NcMs). In the present paper, the interface effects on the effective elastic property of NcMs are investigated. First, an atomic potential method is suggested for estimating the effective elastic modulus of an interface phase. Then, the Mori-Tanaka effective field method is employed to determine the overall effective elastic moduli of a nanocrystalline material, which is regarded as a binary composite consisting of a crystal or inclusion phase with regular lattice connected by an amorphous-like interface or matrix phase. Finally, the stiffening effects of strain gradients are examined on the effective elastic property by using the strain gradient theory to analyze a representative unit cell. Our analysis shows two physical mechanisms of interfaces that influence the effective stiffness and other mechanical properties of materials. One is the softening effect due to the distorted atomic structures and the increased atomic spacings in interface regions, and another is the baffling effect due to the existence of boundary layers between the interface phase and the crystalline phase

A novel asymptotic expansion homogenization analysis for 3-D composite with relieved periodicity in the thickness direction

KAUST Repository

Nasution, Muhammad Ridlo Erdata

2014-06-01

A new asymptotic expansion homogenization analysis is proposed to analyze 3-D composite in which thermomechanical and finite thickness effects are considered. Finite thickness effect is captured by relieving periodic boundary condition at the top and bottom of unit-cell surfaces. The mathematical treatment yields that only 2-D periodicity (i.e. in in-plane directions) is taken into account. A unit-cell representing the whole thickness of 3-D composite is built to facilitate the present method. The equivalent in-plane thermomechanical properties of 3-D orthogonal interlock composites are calculated by present method, and the results are compared with those obtained by standard homogenization method (with 3-D periodicity). Young\\'s modulus and Poisson\\'s ratio obtained by present method are also compared with experiments whereby a good agreement is particularly found for the Young\\'s modulus. Localization analysis is carried out to evaluate the stress responses within the unit-cell of 3-D composites for two cases: thermal and biaxial tensile loading. Standard finite element (FE) analysis is also performed to validate the stress responses obtained by localization analysis. It is found that present method results are in a good agreement with standard FE analysis. This fact emphasizes that relieving periodicity in the thickness direction is necessary to accurately simulate the real free-traction condition in 3-D composite. © 2014 Elsevier Ltd.

A novel asymptotic expansion homogenization analysis for 3-D composite with relieved periodicity in the thickness direction

KAUST Repository

Nasution, Muhammad Ridlo Erdata; Watanabe, Naoyuki; Kondo, Atsushi; Yudhanto, Arief

2014-01-01

A new asymptotic expansion homogenization analysis is proposed to analyze 3-D composite in which thermomechanical and finite thickness effects are considered. Finite thickness effect is captured by relieving periodic boundary condition at the top and bottom of unit-cell surfaces. The mathematical treatment yields that only 2-D periodicity (i.e. in in-plane directions) is taken into account. A unit-cell representing the whole thickness of 3-D composite is built to facilitate the present method. The equivalent in-plane thermomechanical properties of 3-D orthogonal interlock composites are calculated by present method, and the results are compared with those obtained by standard homogenization method (with 3-D periodicity). Young's modulus and Poisson's ratio obtained by present method are also compared with experiments whereby a good agreement is particularly found for the Young's modulus. Localization analysis is carried out to evaluate the stress responses within the unit-cell of 3-D composites for two cases: thermal and biaxial tensile loading. Standard finite element (FE) analysis is also performed to validate the stress responses obtained by localization analysis. It is found that present method results are in a good agreement with standard FE analysis. This fact emphasizes that relieving periodicity in the thickness direction is necessary to accurately simulate the real free-traction condition in 3-D composite. © 2014 Elsevier Ltd.

Estimation of Iranian price elasticities of residential electricity demand

Directory of Open Access Journals (Sweden)

Yeganeh Mousavi Jahromi

2014-06-01

Full Text Available This paper presents a study to determine demand for electricity in city of Yazd, Iran over the period of 1998-2008. Using vector error correction model (VECM based on seasonal information, the study determines that electricity has no elasticity in short term in household expenditure. Therefore, government policy on increasing price of electricity will not influence demand. However, electricity maintains elasticity over the long-term period and an increase on price of electricity could motivate consumers to reduce their consumption by purchasing energy efficient facilities. Therefore, any governmental strategy to increase price may have positive impact on economy. The study also detects a positive and meaningful relationship between temperature and electricity consumption.

Effects of thermal residual stresses and fiber packing on deformation of metal-matrix composites

International Nuclear Information System (INIS)

Nakamura, T.; Suresh, S.

1993-01-01

The combined effects of thermal residual stresses and fiber spatial distribution on the deformation of a 6061 aluminum alloy containing a fixed concentration unidirectional boron fibers have been analyzed using detailed finite element models. The geometrical structure includes perfectly periodic, uniformly space fiber arrangements in square and hexagonal cells, as well as different cells in which either 30 or 60 fibers are randomly placed in the ductile matrix. The model involves an elastic-plastic matrix, elastic fibers, and mechanically bonded interfaces. The results indicate that both fiber packing and thermal residual stresses can have a significant effect on the stress-strain characteristics of the composite. The thermal residual stresses cause pronounced matrix yielding which also influences the apparent overall stiffness of the composite during the initial stages of subsequent far-field loading along the axial and transverse direction. Furthermore, the thermal residual stresses apparently elevate the flow stress of the composite during transverse tension. Such effects can be traced back to the level of constraint imposed on the matrix by local fiber spacing. The implications of the present results to the processing of the composites are also briefly addressed

Elastic properties of silicon nitride ceramics reinforced with graphene nanofillers

Czech Academy of Sciences Publication Activity Database

Seiner, Hanuš; Ramírez, C.; Koller, M.; Sedlák, Petr; Landa, Michal; Miranzo, P.; Belmonte, M.; Osendí, M. I.

2015-01-01

Roč. 87, December (2015), s. 675-680 ISSN 0264-1275 R&D Projects: GA ČR GB14-36566G Institutional support: RVO:61388998 Keywords : multilayer graphene * graphene oxide (GO) * silicon nitride * elastic constants * elastic modulus * shear modulus Subject RIV: JI - Composite Materials Impact factor: 3.997, year: 2015 http://www.sciencedirect.com/science/article/pii/S0264127515302938/pdfft?md5=571e00fd7f976e9b66ed789ae2a868b2&pid=1-s2.0-S0264127515302938-main.pdf

Autonomic Vertical Elasticity of Docker Containers with ElasticDocker

OpenAIRE

Al-Dhuraibi , Yahya; Paraiso , Fawaz; Djarallah , Nabil; Merle , Philippe

2017-01-01

International audience; Elasticity is the key feature of cloud computing to scale computing resources according to application workloads timely. In the literature as well as in industrial products, much attention was given to the elasticity of virtual machines, but much less to the elasticity of containers. However, containers are the new trend for packaging and deploying microservices-based applications. Moreover, most of approaches focus on horizontal elasticity, fewer works address vertica...

The effect of dietary and/or cosmetic argan oil on postmenopausal skin elasticity

Directory of Open Access Journals (Sweden)

Qiraouani Boucetta K

2015-01-01

Full Text Available Kenza Qiraouani Boucetta,1 Zoubida Charrouf,2 Hassan Aguenaou,3 Abdelfattah Derouiche,4 Yahya Bensouda1 1Research Team on Formulation and Biopharmacy, Research Center for Drug, Faculty of Medicine and Pharmacy, Mohammed V University, Rabat, Morocco; 2Faculty of Sciences, Mohammed V University, Rabat, Morocco; 3Mixed Unit of Research in Nutrition, ITU / CNESTEN, Ibn Tofail University, Kenitra, Morocco; 4Faculty of Sciences, Hassan II University, Casablanca, Morocco Background: During menopause, the decrease of estrogenic secretion induces the disruption of skin functioning, thus causing the decline in skin elasticity characteristic of skin aging. The purpose of this study was to evaluate in postmenopausal women the effect of daily consumption and/or application of argan oil on skin elasticity.Materials and methods: Sixty postmenopausal women consumed butter during the stabilization period and were randomly divided into two groups for the intervention period: the treatment group of 30 participants received dietary argan oil, the control group of 30 participants received olive oil, and both groups applied cosmetic argan oil in the left volar forearm during a 60-day period. Assessments of skin elasticity parameters, ie, the three R-parameters (R2 or gross-elasticity of the skin, R5 or net elasticity of the skin, and R7 or biological elasticity, and the resonance running time (RRT at both volar forearms of the two groups were performed during three visits: before starting oils consumption and application, after 30 days of oils consumption and application, and after 60 days of oils consumption and application.Results: The consumption of argan oil led to a significant increase of gross-elasticity of the skin (R2 (P<0.001, net elasticity of the skin (R5 (P<0.001, biological elasticity (R7 (P<0.001, and a significant decrease of RRT (P=0.002. The application of argan oil led to a significant increase of gross-elasticity of the skin (R2 (P<0.001, net

Effect of reinforcement volume fraction on the density & elastic ...

African Journals Online (AJOL)

Effect of reinforcement volume fraction on the density & elastic parameters of BMG's matrix composites. Wahiba Metiri 1, Fatiha Hadjoub1, 2 and Leila Touati Tliba 1. 1 Laboratoire des Semi-Conducteurs, Département de Physique, Faculté des Sciences, Université Badji-. Mokhtar, BP 12, Annaba -23000, Algeria.

Price and income elasticities of residential energy demand in Germany

International Nuclear Information System (INIS)

Schulte, Isabella; Heindl, Peter

2017-01-01

We apply a quadratic expenditure system to estimate price and expenditure elasticities of residential energy demand (electricity and heating) in Germany. Using official expenditure data from 1993 to 2008, we estimate an expenditure elasticity for electricity of 0.3988 and of 0.4055 for space heating. The own price elasticity for electricity is −0.4310 and −0.5008 in the case of space heating. Disaggregation of households by expenditure and socio-economic composition reveals that the behavioural response to energy price changes is weaker (stronger) for low-income (top-income) households. There are considerable economies of scale in residential energy use but scale effects are not well approximated by the new OECD equivalence scale. Real increases in energy prices show a regressive pattern of incidence, implying that the welfare consequences of direct energy taxation are larger for low income households. The application of zero-elasticities in assessments of welfare consequences of energy taxation strongly underestimates potential welfare effects. The increase in inequality is 22% smaller when compared to the application of disaggregated price and income elasticities as estimated in this paper. - Highlights: • We estimate price, income, and expenditure elasticities for residential energy demand in Germany. • We differentiate elasticities by income groups and household type. • Electricity and space heating are necessary goods since the expenditure elasticities are smaller than unity. • Low-income households show a weaker reaction to changing prices when compared to high-income households. • Direct energy taxation has regressive effects, meaning that larger burdens fall upon low-income households.

Forces and torques on rigid inclusions in an elastic environment: Resulting matrix-mediated interactions, displacements, and rotations

Science.gov (United States)

Puljiz, Mate; Menzel, Andreas M.

2017-05-01

Embedding rigid inclusions into elastic matrix materials is a procedure of high practical relevance, for instance, for the fabrication of elastic composite materials. We theoretically analyze the following situation. Rigid spherical inclusions are enclosed by a homogeneous elastic medium under stick boundary conditions. Forces and torques are directly imposed from outside onto the inclusions or are externally induced between them. The inclusions respond to these forces and torques by translations and rotations against the surrounding elastic matrix. This leads to elastic matrix deformations, and in turn results in mutual long-ranged matrix-mediated interactions between the inclusions. Adapting a well-known approach from low-Reynolds-number hydrodynamics, we explicitly calculate the displacements and rotations of the inclusions from the externally imposed or induced forces and torques. Analytical expressions are presented as a function of the inclusion configuration in terms of displaceability and rotateability matrices. The role of the elastic environment is implicitly included in these relations. That is, the resulting expressions allow a calculation of the induced displacements and rotations directly from the inclusion configuration, without having to explicitly determine the deformations of the elastic environment. In contrast to the hydrodynamic case, compressibility of the surrounding medium is readily taken into account. We present the complete derivation based on the underlying equations of linear elasticity theory. In the future, the method will, for example, be helpful to characterize the behavior of externally tunable elastic composite materials, to accelerate numerical approaches, as well as to improve the quantitative interpretation of microrheological results.

Elastic recoil detection (ERD) with extremely heavy ions

International Nuclear Information System (INIS)

Forster, J.S.; Davies, J.A.; Siegele, R.; Wallace, S.G.; Zelenitsky, D.

1996-01-01

Extremely heavy-ion beams such as 209 Bi in elastic recoil detection (ERD) make ERD a uniquely valuable technique for thin-film analysis of elements with mass ≤100. We report ERD measurements of compositional analysis of dinosaur eggshells and bones. We also show the capability of the ERD technique on studies of thin-film, high-temperature superconductors. (orig.)

Elastic-plastic analysis of the toroidal field coil inner leg of the compact ignition tokamak

International Nuclear Information System (INIS)

Horie, T.

1987-07-01

Elastic-plastic analyses were made for the inner leg of the Compact Ignition Tokamak toroidal field (TF) coil, which is made of copper-Inconel composite material. From the result of the elastic-plastic analysis, the effective Young's moduli of the inner leg were determined by the analytical equations. These Young's moduli are useful for the three-dimensional, elastic, overall TF coil analysis. Comparison among the results of the baseline design (R = 1.324 m), the bucked pressless design, the 1.527-m major radius design, and the 1.6-m major radius design was also made, based on the elastic-plastic TF coil inner leg analyses

The Calculation of Weighted Price Elasticity of Tax: Turkey (1998-2013

Directory of Open Access Journals (Sweden)

Engin YILMAZ

2015-06-01

Full Text Available In this study, the assumption of “the weighted price elasticity of tax is a unit in the developing countries” suggested in the first studies which examine the impacts of the inflation on tax revenues, will be reevaluated for Turkey in the period of 1998-2013. We use Turkish tax and price index data for calculating the weighted price elasticity of tax. Via the method of dynamic ordinary least squares (DOLS, the long run weighted price elasticity of tax system is guessed. The importance of this study is the fact that this is first study intended to the calculation of the weighted price elasticity of tax for Turkey. In this sense, it will be instructive study for the reconsideration of the assumption of “the weighted price elasticity of tax is a unit in the developing countries”.

Elastic interactions between hydrogen atoms in metals. II. Elastic interaction energies

International Nuclear Information System (INIS)

Shirley, A.I.; Hall, C.K.

1986-01-01

The fully harmonic lattice approximation derived in a previous paper is used to calculate the elastic interaction energies in the niobium-hydrogen system. The permanent-direct, permanent-indirect, induced-direct, and induced-indirect forces calculated previously each give rise to a corresponding elastic interaction between hydrogen atoms. The latter three interactions have three- and four-body terms in addition to the usual two-body terms. These quantities are calculated and compared with the corresponding two-body permanent elastic interactions obtained in the harmonic-approximation treatment of Horner and Wagner. The results show that the total induced elastic energy is approximately (1/3) the size of the total permanent elastic energy and opposite to it in sign. The total elastic energy due to three-body interactions is approximately (1/4) the size of the total two-body elastic energy, while the total four-body elastic energy is approximately 5% of the total two-body energy. These additional elastic energies are expected to have a profound effect on the thermodynamic and phase-change behavior of a metal hydride

From plastic to elastic stress relaxation in highly mismatched SiGe/Si heterostructures

International Nuclear Information System (INIS)

Isa, Fabio; Salvalaglio, Marco; Dasilva, Yadira Arroyo Rojas; Jung, Arik; Isella, Giovanni; Erni, Rolf; Niedermann, Philippe; Gröning, Pierangelo; Montalenti, Francesco; Känel, Hans von

2016-01-01

We present a detailed experimental and theoretical analysis of the epitaxial stress relaxation process in micro-structured compositionally graded alloys. We focus on the pivotal SiGe/Si(001) system employing patterned Si substrates at the micrometre-size scale to address the distribution of threading and misfit dislocations within the heterostructures. SiGe alloys with linearly increasing Ge content were deposited by low energy plasma enhanced chemical vapour deposition resulting in isolated, tens of micrometre tall 3D crystals. We demonstrate that complete elastic relaxation is achieved by appropriate choice of the Ge compositional grading rate and Si pillar width. We investigate the nature and distribution of dislocations along the [001] growth direction in SiGe crystals by transmission electron microscopy, chemical defect etching and etch pit counting. We show that for 3 μm wide Si pillars and a Ge grading rate of 1.5% μm −1 , only misfit dislocations are present while their fraction is reduced for higher Ge grading rates and larger structures due to dislocation interactions. The experimental results are interpreted with the help of theoretical calculations based on linear elasticity theory describing the competition between purely elastic and plastic stress relaxation with increasing crystal width and Ge compositional grading rate.

Thermal elastic deformations of the planet Mercury.

Science.gov (United States)

Liu, H.-S.

1972-01-01

The variation in solar heating due to the resonance rotation of Mercury produces periodic elastic deformations on the surface of the planet. The thermal stress and strain fields under Mercury's surface are calculated after certain simplifications. It is found that deformations penetrate to a greater depth than the variation of solar heating, and that the thermal strain on the surface of the planet pulsates with an amplitude of .004 and a period of 176 days.

Elastic Metamaterials with Simultaneously Negative Effective Shear Modulus and Mass Density

KAUST Repository

Wu, Ying; Lai, Yun; Zhang, Zhao-Qing

2011-01-01

We propose a type of elastic metamaterial comprising fluid-solid composite inclusions which can possess a negative shear modulus and negative mass density over a large frequency region. Such a material has the unique property that only transverse

Sound transmission through stiffened double-panel structures lined with elastic porous materials

Science.gov (United States)

Mathur, Gopal P.; Tran, Boi N.; Bolton, J. S.; Shiau, Nae-Ming

This paper presents transmission loss prediction models for a periodically stiffened panel and stiffened double-panel structures using the periodic structure theory. The inter-panel cavity in the double-panels structures can be modeled as being separated by an airspace or filled with an elastic porous layer in various configurations. The acoustic behavior of elastic porous layer is described by a theory capable of accounting fully for multi-dimensional wave propagation in such materials. The predicted transmission loss of a single stiffened panel is compared with the measured data.

Architecture Of Uzbekistan Of The Ancient Period Style Features And Composition Laws

Directory of Open Access Journals (Sweden)

Nurmukhamedova Shoira Zahidovna

2015-08-01

Full Text Available Specific features of the development of architecture in Uzbekistan in ancient period are considered in the paper. The author emphasizes the role of building materials and structures studies the composition of ancient settlements in Khorezm and Bactria reveals a high level of military architecture and planning principles of residential and castle structures.

Own-wage labor supply elasticities: variation across time and estimation methods

Directory of Open Access Journals (Sweden)

Olivier Bargain

2016-10-01

Full Text Available Abstract There is a huge variation in the size of labor supply elasticities in the literature, which hampers policy analysis. While recent studies show that preference heterogeneity across countries explains little of this variation, we focus on two other important features: observation period and estimation method. We start with a thorough survey of existing evidence for both Western Europe and the USA, over a long period and from different empirical approaches. Then, our meta-analysis attempts to disentangle the role of time changes and estimation methods. We highlight the key role of time changes, documenting the incredible fall in labor supply elasticities since the 1980s not only for the USA but also in the EU. In contrast, we find no compelling evidence that the choice of estimation method explains variation in elasticity estimates. From our analysis, we derive important guidelines for policy simulations.

Prediction of elastic properties for polymer-particle nanocomposites exhibiting an interphase

International Nuclear Information System (INIS)

Deng Fei; Van Vliet, Krystyn J

2011-01-01

Particle-polymer nanocomposites often exhibit mechanical properties described poorly by micromechanical models that include only the particle and matrix phases. Existence of an interfacial region between the particle and matrix, or interphase, has been posited and indirectly demonstrated to account for this effect. Here, we present a straightforward analytical approach to estimate effective elastic properties of composites comprising particles encapsulated by an interphase of finite thickness and distinct elastic properties. This explicit solution can treat nanocomposites that comprise either physically isolated nanoparticles or agglomerates of such nanoparticles; the same framework can also treat physically isolated nanoparticle aggregates or agglomerates of such aggregates. We find that the predicted elastic moduli agree with experiments for three types of particle-polymer nanocomposites, and that the predicted interphase thickness and stiffness of carbon black-rubber nanocomposites are consistent with measured values. Finally, we discuss the relative influence of the particle-polymer interphase thickness and stiffness to identify maximum possible changes in the macroscale elastic properties of such materials.

Fast reactor core design studies to cope with TRU fuel composition changes in the LWR-to-FBR transition period

International Nuclear Information System (INIS)

Kawashima, Katsuyuki; Maruyama, Shuhei; Ohki, Shigeo; Mizuno, Tomoyasu

2009-01-01

As part of the Fast Reactor Cycle Technology Development Project (FaCT Project), sodium-cooled fast reactor core design efforts have been made to cope with the TRU fuel composition changes expected during LWR-to-FBR transition period, in which a various kind of TRU fuel compositions are available depending on the characteristics of the LWR spent fuels and a way of recycling them. A 750 MWe mixed-oxide fuel core is firstly defined as a FaCT medium-size reference core and its neutronics characteristics are determined. The core is a high internal conversion type and has an average burnup of 150 GWD/T. The reference TRU fuel composition is assumed to come from the FBR equilibrium state. Compared to the LWR-to-FBR transition period, the TRU fuels in the FBR equilibrium period are multi-recycled through fast reactors and have a different composition. An available TRU fuel composition is determined by fast reactor spent fuel multi-recycling scenarios. Then the FaCT core corresponding to the TRU fuel with different compositions is set according to the TRU fuel composition changes in LWR-to-FBR transition period, and the key core neutronics characteristics are assessed. It is shown that among the core neutronics characteristics, the burnup reactivity and the safety parameters such as sodium void reactivity and Doppler coefficient are significantly influenced by the TRU fuel composition changes. As a result, a general characteristic in the FaCT core design to cope with TRU fuel composition changes is grasped and the design envelopes are identified in terms of the burnup reactivity and the safety parameters. (author)

Proposal of Design Formulae for Equivalent Elasticity of Masonry Structures Made with Bricks of Low Modulus

Directory of Open Access Journals (Sweden)

Muhammad Ridwan

2017-01-01

Full Text Available Bricks of low elastic modulus are occasionally used in some developing countries, such as Indonesia and India. Most of the previous research efforts focused on masonry structures built with bricks of considerably high elastic modulus. The objective of this study is to quantify the equivalent elastic modulus of lower-stiffness masonry structures, when the mortar has a higher modulus of elasticity than the bricks, by employing finite element (FE simulations and adopting the homogenization technique. The reported numerical simulations adopted the two-dimensional representative volume elements (RVEs using quadrilateral elements with four nodes. The equivalent elastic moduli of composite elements with various bricks and mortar were quantified. The numerically estimated equivalent elastic moduli from the FE simulations were verified using previously established test data. Hence, a new simplified formula for the calculation of the equivalent modulus of elasticity of such masonry structures is proposed in the present study.

Cavitation instabilities between fibres in a metal matrix composite

DEFF Research Database (Denmark)

Tvergaard, Viggo

2016-01-01

induced by bonding to the ceramics that only show elastic deformation. In an MMC the stress state in the metal matrix is highly non-uniform, varying between regions where shear stresses are dominant and regions where hydrostatic tension is strong. An Al–SiC whisker composite with a periodic pattern......Short fibre reinforced metal matrix composites (MMC) are studied here to investigate the possibility that a cavitation instability can develop in the metal matrix. The high stress levels needed for a cavitation instability may occur in metal–ceramic systems due to the constraint on plastic flow...... of transversely staggered fibres is here modelled by using an axisymmetric cell model analysis. First the critical stress level is determined for a cavitation instability in an infinite solid made of the Al matrix material. By studying composites with different distributions and aspect ratios of the fibres...

Graphene nanoribbon as an elastic damper

Science.gov (United States)

Evazzade, Iman; Lobzenko, Ivan P.; Saadatmand, Danial; Korznikova, Elena A.; Zhou, Kun; Liu, Bo; Dmitriev, Sergey V.

2018-05-01

Heterostructures composed of dissimilar two-dimensional nanomaterials can have nontrivial physical and mechanical properties which are potentially useful in many applications. Interestingly, in some cases, it is possible to create heterostructures composed of weakly and strongly stretched domains with the same chemical composition, as has been demonstrated for some polymer chains, DNA, and intermetallic nanowires supporting this effect of two-phase stretching. These materials, at relatively strong tension forces, split into domains with smaller and larger tensile strains. Within this region, average strain increases at constant tensile force due to the growth of the domain with the larger strain, at the expense of the domain with smaller strain. Here, the two-phase stretching phenomenon is described for graphene nanoribbons with the help of molecular dynamics simulations. This unprecedented feature of graphene that is revealed in our study is related to the peculiarities of nucleation and the motion of the domain walls separating the domains of different elastic strain. It turns out that the loading–unloading curves exhibit a hysteresis-like behavior due to the energy dissipation during the domain wall nucleation and motion. Here, we put forward the idea of implementing graphene nanoribbons as elastic dampers, efficiently converting mechanical strain energy into heat during cyclic loading–unloading through elastic extension where domains with larger and smaller strains coexist. Furthermore, in the regime of two-phase stretching, graphene nanoribbon is a heterostructure for which the fraction of domains with larger and smaller strain, and consequently its physical and mechanical properties, can be tuned in a controllable manner by applying elastic strain and/or heat.

Case Study: Body Composition Periodization in an Olympic-Level Female Middle-Distance Runner Over a 9-Year Career.

Science.gov (United States)

Stellingwerff, Trent

2018-05-25

This case study features an Olympic-level female middle-distance runner implementing a science-based approach to body composition periodization. Data are emerging to suggest that it is not sustainable from a health and/or performance perspective to be at peak body composition year-round, so body composition needs to be strategically periodized. Anthropometric (n = 44), hematological, other health measures, and 1,500-m race performances (n = 83) were periodically assessed throughout a 9-year career. General preparation phase (September to April) featured the athlete at ∼2-4% over ideal competition phase body weight (BW) and body fat (%), with optimal energy availability being prioritized. The competition body composition optimization phase (May to August) included creating an individualized time frame and caloric deficit with various feedback metrics (BW, performance, and hunger) to guide the process. There were significant seasonal fluctuations in anthropometric outcomes between phases (47.3 ± 0.8 vs. 48.3 ± 0.9 kg BW; 53.6 ± 7.8 vs. 61.6 ± 9.7 mm International Society for the Advancement of Kinanthropometry sum of 8 [So8] skinfolds; p career (r = -.838; p = .018). The range of body composition during the competition period was 46.0-48.0 kg BW and a So8 range was 42.0-55.9 mm. There were also significant positive correlations between slower 1,500-m race times and increasing So8 (r = .437; p career injuries. This case study demonstrates a body composition periodization approach that allowed for targeted peak yearly performances, which improved throughout her career, while maximizing training adaptation and long-term athlete health through optimal energy availability.

Structural aspects of elastic deformation of a metallic glass

International Nuclear Information System (INIS)

Hufnagel, T. C.; Ott, R. T.; Almer, J.

2006-01-01

We report the use of high-energy x-ray scattering to measure strain in a Zr 57 Ti 5 Cu 20 Ni 8 Al 10 bulk metallic glass in situ during uniaxial compression in the elastic regime up to stresses of approximately 60% of the yield stress. The strains extracted in two ways--directly from the normalized scattering data and from the pair correlation functions--are in good agreement with each other for length scales greater than 4 A. The elastic modulus calculated on the basis of this strain is in good agreement with that reported for closely related amorphous alloys based on macroscopic measurements. The strain measured for atoms in the nearest-neighbor shell, however, is smaller than that for more distant shells, and the effective elastic modulus calculated from the strain on this scale is therefore larger, comparable to crystalline alloys of similar composition. These observations are in agreement with previously proposed models in which the nominally elastic deformation of a metallic glass has a significant anelastic component due to atomic rearrangements in topologically unstable regions of the structure. We also observe that the distribution of the atomic-level stresses in the glass becomes more uniform during loading. This implies that the stiffness of metallic glasses may have an entropic contribution, analogous to the entropic contribution in rubber elasticity

Estimating petroleum products demand elasticities in Nigeria. A multivariate cointegration approach

International Nuclear Information System (INIS)

Iwayemi, Akin; Adenikinju, Adeola; Babatunde, M. Adetunji

2010-01-01

This paper formulates and estimates petroleum products demand functions in Nigeria at both aggregative and product level for the period 1977 to 2006 using multivariate cointegration approach. The estimated short and long-run price and income elasticities confirm conventional wisdom that energy consumption responds positively to changes in GDP and negatively to changes in energy price. However, the price and income elasticities of demand varied according to product type. Kerosene and gasoline have relatively high short-run income and price elasticities compared to diesel. Overall, the results show petroleum products to be price and income inelastic. (author)

Estimating petroleum products demand elasticities in Nigeria. A multivariate cointegration approach

Energy Technology Data Exchange (ETDEWEB)

Iwayemi, Akin; Adenikinju, Adeola; Babatunde, M. Adetunji [Department of Economics, University of Ibadan, Ibadan (Nigeria)

2010-01-15

This paper formulates and estimates petroleum products demand functions in Nigeria at both aggregative and product level for the period 1977 to 2006 using multivariate cointegration approach. The estimated short and long-run price and income elasticities confirm conventional wisdom that energy consumption responds positively to changes in GDP and negatively to changes in energy price. However, the price and income elasticities of demand varied according to product type. Kerosene and gasoline have relatively high short-run income and price elasticities compared to diesel. Overall, the results show petroleum products to be price and income inelastic. (author)

An asymptotic homogenization model for smart 3D grid-reinforced composite structures with generally orthotropic constituents

International Nuclear Information System (INIS)

Hassan, E M; Kalamkarov, A L; Georgiades, A V; Challagulla, K S

2009-01-01

A comprehensive micromechanical model for smart 3D composite structures reinforced with a periodic grid of generally orthotropic cylindrical reinforcements that also exhibit piezoelectric behavior is developed. The original boundary value problem characterizing the piezothermoelastic behavior of these structures is decoupled into a set of three simpler unit cell problems dealing, separately, with the elastic, piezoelectric and thermal expansion characteristics of the smart composite. The technique used is that of asymptotic homogenization and the solution of the unit cell problems permits determination of the effective elastic, piezoelectric and thermal expansion coefficients. The general orthotropy of the constituent materials is very important from the practical viewpoint and makes the analysis much more complicated. Several examples of practical interest are used to illustrate the work including smart 3D composites with cubic and conical embedded grids as well as diagonally reinforced smart structures. It is also shown in this work that in the limiting particular case of 2D grid-reinforced structures with isotropic reinforcements our results converge to earlier published results

Homogenization-based interval analysis for structural-acoustic problem involving periodical composites and multi-scale uncertain-but-bounded parameters.

Science.gov (United States)

Chen, Ning; Yu, Dejie; Xia, Baizhan; Liu, Jian; Ma, Zhengdong

2017-04-01

This paper presents a homogenization-based interval analysis method for the prediction of coupled structural-acoustic systems involving periodical composites and multi-scale uncertain-but-bounded parameters. In the structural-acoustic system, the macro plate structure is assumed to be composed of a periodically uniform microstructure. The equivalent macro material properties of the microstructure are computed using the homogenization method. By integrating the first-order Taylor expansion interval analysis method with the homogenization-based finite element method, a homogenization-based interval finite element method (HIFEM) is developed to solve a periodical composite structural-acoustic system with multi-scale uncertain-but-bounded parameters. The corresponding formulations of the HIFEM are deduced. A subinterval technique is also introduced into the HIFEM for higher accuracy. Numerical examples of a hexahedral box and an automobile passenger compartment are given to demonstrate the efficiency of the presented method for a periodical composite structural-acoustic system with multi-scale uncertain-but-bounded parameters.

Optimization of directional elastic energy propagation

DEFF Research Database (Denmark)

Andreassen, Erik; Chang, Hannah R.; Ruzzene, Massimo

2016-01-01

The aim of this paper is to demonstrate how topology optimization can be used to design a periodically perforated plate, in order to obtain a tailored anisotropic group velocity profile. The main method is demonstrated on both low and high frequency bending wave propagation in an aluminum plate......, but is general in the sense that it could be used to design periodic structures with frequency dependent group velocity profiles for any kind of elastic wave propagation. With the proposed method the resulting design is manufacturable. Measurements on an optimized design compare excellently with the numerical...

Ultrasonic Characterisation of Epoxy Resin/Polyethylene Terephthalate (PET Char Powder Composites

Directory of Open Access Journals (Sweden)

Imran ORAL

2016-11-01

Full Text Available This study is carried out in order to determine the elastic properties of the Epoxy Resin (ER / Polyethylene terephthalate (PET Char Powder Composites by ultrasonic wave velocity measurement method. Plastic waste was recycled as raw material for the preparation of epoxy composite materials. The supplied chars were mixed with epoxy resin matrix at weight percentages of 10 %, 20 % and 30 % for preparing ER/PET Char Powder (PCP composites. The effect of PET char powder on the elastic properties of ER/PCP composites were investigated by ultrasonic pulse-echo method. According to the obtained results, the composition ratio of 80:20 is the most appropriate composition ratio, which gave the highest elastic constants values for ER/PCP composites. On the other hand, the best electrical conductivity value was obtained for 70:30 composition ratio. It was observed that ultrasonic shear wave velocity correlated more perfectly than any other parameters with hardness.DOI: http://dx.doi.org/10.5755/j01.ms.22.4.12190

Investigation of translaminar fracture in fibrereinforced composite laminates---applicability of linear elastic fracture mechanics and cohesive-zone model

Science.gov (United States)

Hou, Fang

With the extensive application of fiber-reinforced composite laminates in industry, research on the fracture mechanisms of this type of materials have drawn more and more attentions. A variety of fracture theories and models have been developed. Among them, the linear elastic fracture mechanics (LEFM) and cohesive-zone model (CZM) are two widely-accepted fracture models, which have already shown applicability in the fracture analysis of fiber-reinforced composite laminates. However, there remain challenges which prevent further applications of the two fracture models, such as the experimental measurement of fracture resistance. This dissertation primarily focused on the study of the applicability of LEFM and CZM for the fracture analysis of translaminar fracture in fibre-reinforced composite laminates. The research for each fracture model consisted of two sections: the analytical characterization of crack-tip fields and the experimental measurement of fracture resistance parameters. In the study of LEFM, an experimental investigation based on full-field crack-tip displacement measurements was carried out as a way to characterize the subcritical and steady-state crack advances in translaminar fracture of fiber-reinforced composite laminates. Here, the fiber-reinforced composite laminates were approximated as anisotropic solids. The experimental investigation relied on the LEFM theory with a modification with respect to the material anisotropy. Firstly, the full-field crack-tip displacement fields were measured by Digital Image Correlation (DIC). Then two methods, separately based on the stress intensity approach and the energy approach, were developed to measure the crack-tip field parameters from crack-tip displacement fields. The studied crack-tip field parameters included the stress intensity factor, energy release rate and effective crack length. Moreover, the crack-growth resistance curves (R-curves) were constructed with the measured crack-tip field parameters

Stimuli-responsive transformation in carbon nanotube/expanding microsphere–polymer composites

International Nuclear Information System (INIS)

Loomis, James; Xu Peng; Panchapakesan, Balaji

2013-01-01

Our work introduces a class of stimuli-responsive expanding polymer composites with the ability to unidirectionally transform their physical dimensions, elastic modulus, density, and electrical resistance. Carbon nanotubes and core–shell acrylic microspheres were dispersed in polydimethylsiloxane, resulting in composites that exhibit a binary set of material properties. Upon thermal or infrared stimuli, the liquid cores encapsulated within the microspheres vaporize, expanding the surrounding shells and stretching the matrix. The microsphere expansion results in visible dimensional changes, regions of reduced polymeric chain mobility, nanotube tensioning, and overall elastic to plastic-like transformation of the composite. Here, we show composite transformations including macroscopic volume expansion (>500%), density reduction (>80%), and elastic modulus increase (>675%). Additionally, conductive nanotubes allow for remote expansion monitoring and exhibit distinct loading-dependent electrical responses. With the ability to pattern regions of tailorable expansion, strength, and electrical resistance into a single polymer skin, these composites present opportunities as structural and electrical building blocks in smart systems. (paper)

Design of the Elastic Modulus of Nanoparticles-Containing PVA/PVAc Films by the Response Surface Method

Science.gov (United States)

Jelinska, N.; Kalnins, M.; Kovalovs, A.; Chate, A.

2015-11-01

By the surface response method, a regression equation is constructed, and the tensile elastic modulus of films made from polyvinyl alcohol/polyvinyl acetate (PVA/PVAc) blends filled with montmorillonite clay and microcrystalline cellulose nanoparticles is investigated. It is established that the introduction of the nanoparticles improves the mechanical properties of the blends in tension considerably: their strength and elastic modulus increase with content of the particles. Using the regression equation, the optimum composition of nanoparticlefilled PVA/PVAc blends with the highest value of elastic modulus is found.

CARAPACE:A novel composite advanced robotic actuator powering assistive compliant exoskeleton preliminary design

OpenAIRE

Masia, Lorenzo; Cappello, Leonardo; Morasso, Pietro; Lachenal, Xavier; Pirrera, Alberto; Weaver, Paul; Mattioni, Filippo

2013-01-01

A novel actuator is introduced that combines an elastically compliant composite structure with conventional electromechanical elements. The proposed design is analogous to that used in Series Elastic Actuators, its distinctive feature being that the compliant composite part offers different stable configurations. In other words, its elastic potential presents points of local minima that correspond to robust stable positions (multistability). This potential is known a priori as a function of t...

Experimentally-based multiscale model of the elastic moduli of bovine trabecular bone and its constituents

Energy Technology Data Exchange (ETDEWEB)

Hamed, Elham [University of Illinois at Urbana-Champaign, Department of Mechanical Science and Engineering, 1206 West Green Street, Urbana, IL 61801 (United States); Novitskaya, Ekaterina, E-mail: eevdokim@ucsd.edu [University of California, San Diego, Department of Mechanical and Aerospace Engineering, Materials Science and Engineering Program, 9500 Gilman Dr., La Jolla, CA 92093 (United States); Li, Jun; Jasiuk, Iwona [University of Illinois at Urbana-Champaign, Department of Mechanical Science and Engineering, 1206 West Green Street, Urbana, IL 61801 (United States); McKittrick, Joanna [University of California, San Diego, Department of Mechanical and Aerospace Engineering, Materials Science and Engineering Program, 9500 Gilman Dr., La Jolla, CA 92093 (United States)

2015-09-01

The elastic moduli of trabecular bone were modeled using an analytical multiscale approach. Trabecular bone was represented as a porous nanocomposite material with a hierarchical structure spanning from the collagen–mineral level to the trabecular architecture level. In parallel, compression testing was done on bovine femoral trabecular bone samples in two anatomical directions, parallel to the femoral neck axis and perpendicular to it, and the measured elastic moduli were compared with the corresponding theoretical results. To gain insights on the interaction of collagen and minerals at the nanoscale, bone samples were deproteinized or demineralized. After such processing, the treated samples remained as self-standing structures and were tested in compression. Micro-computed tomography was used to characterize the hierarchical structure of these three bone types and to quantify the amount of bone porosity. The obtained experimental data served as inputs to the multiscale model and guided us to represent bone as an interpenetrating composite material. Good agreement was found between the theory and experiments for the elastic moduli of the untreated, deproteinized, and demineralized trabecular bone. - Highlights: • A multiscale model was used to predict the elastic moduli of trabecular bone. • Samples included demineralized, deproteinized and untreated bone. • The model portrays bone as a porous, interpenetrating two phase composite. • The experimental elastic moduli for trabecular bone fell between theoretical bounds.

Experimentally-based multiscale model of the elastic moduli of bovine trabecular bone and its constituents

International Nuclear Information System (INIS)

Hamed, Elham; Novitskaya, Ekaterina; Li, Jun; Jasiuk, Iwona; McKittrick, Joanna

2015-01-01

The elastic moduli of trabecular bone were modeled using an analytical multiscale approach. Trabecular bone was represented as a porous nanocomposite material with a hierarchical structure spanning from the collagen–mineral level to the trabecular architecture level. In parallel, compression testing was done on bovine femoral trabecular bone samples in two anatomical directions, parallel to the femoral neck axis and perpendicular to it, and the measured elastic moduli were compared with the corresponding theoretical results. To gain insights on the interaction of collagen and minerals at the nanoscale, bone samples were deproteinized or demineralized. After such processing, the treated samples remained as self-standing structures and were tested in compression. Micro-computed tomography was used to characterize the hierarchical structure of these three bone types and to quantify the amount of bone porosity. The obtained experimental data served as inputs to the multiscale model and guided us to represent bone as an interpenetrating composite material. Good agreement was found between the theory and experiments for the elastic moduli of the untreated, deproteinized, and demineralized trabecular bone. - Highlights: • A multiscale model was used to predict the elastic moduli of trabecular bone. • Samples included demineralized, deproteinized and untreated bone. • The model portrays bone as a porous, interpenetrating two phase composite. • The experimental elastic moduli for trabecular bone fell between theoretical bounds

Micromechanical experimental analysis and modelling of elastic and damageable behaviour of unidirectional SiC/SiC composites

International Nuclear Information System (INIS)

Chateau, C.

2011-01-01

Because of their potential use as a cladding material in future nuclear reactors, the complex mechanical behavior of SiC/SiC composites, which combines damage and anisotropy, must be understood and predictable. As part of a multi-scale approach, this work focuses on the first scale change: from the elementary constituents to the tow. Micromechanical approaches are implemented to describe the macroscopic behavior of the tow taking into account its microstructure heterogeneity and damage mechanisms occurring at the local scale. A representative virtual microstructure is generated based on a detailed microstructural investigation of the tow and its elastic response is studied by numerical homogenization. In addition to addressing the mechanical RVE issue, this study highlights the significant effects of residual porosity on the transverse behavior of the tow, due to the matrix infiltration process. The longitudinal damage is being studied through mini-composites, for which the evolution of microscopic damage mechanisms (matrix cracks and fiber breaks) is experimentally analyzed (in-situ SEM and tomography tensile tests). The identification of interfacial parameters of a 1D statistical damage model is based on the experimental characterization. Conventional assumptions of such models can adequately describe matrix cracking at macro and micro scale. However it is necessary to change them to get a proper prediction of ultimate failure. (author) [fr

Phase-field models of microstructure evolution in a system with elastic inhomogeneity and defects

Science.gov (United States)

Hu, Shenyang

In this thesis, the phase-field approach is employed to study the effect of elastic inhomogeneity and structural defects on phase separation kinetics and morphological evolution in bulk and film systems, the precipitation of theta ' phase (Al2Cu) in Al-Cu alloys, and solute strengthening of alloys. By combining the iteration method for calculating the elastic energy and a semi-implicit spectral method for solving the Cahn-Hilliard equation an extremely efficient phase-field model is developed for studying morphological evolution in coherent systems with large elastic inhomogeneity. Spinodal decomposition in a thin film with periodically distributed arrays of interfacial dislocations is simulated. The results show that the periodic stress field associated with the array of interfacial dislocations leads to a directional phase separation and the formation of ordered microstructures. The metastable theta' (Al2Cu) precipitates are one of the primary strengthening precipitates in Al-Cu alloys. They are of a plate-like shape with strong interfacial energy and mobility anisotropies. A phase-field model which can automatically incorporate the thermodynamic and kinetic information from databases is developed. The relationships between phase-field model parameters and material thermodynamic and kinetic properties are established. Systematic simulations of theta' growth in 1D, 2D and 3D are carried out. The growth of a single theta ' precipitate in 1D exactly reproduces the results from analytical solutions. The phase-filed model can serve as a basis for quantitative understanding of the influence of elastic energy, interface energy anisotropy and interface mobility anisotropy on the precipitation of theta' in Al-Cu alloys. Precipitates and solutes are commonly used to strengthen alloys. A phase field model of dislocation dynamics, which employs 12 order parameter fields to describe the dislocation distribution in a single fcc crystal, and one composition field to describe

The Relationship between Elastic Properties and Shear Fabric in Clay-Rich Fault Gouge

Science.gov (United States)

Kenigsberg, A.; Saffer, D. M.; Riviere, J.; Ryan, K. L.; Marone, C.

2016-12-01

The low mechanical strength of major crustal faults remains a fundamental problem in geophysics and earthquake mechanics. Although both clay abundance and shear fabric are known as key controls on the frictional weakening of faults, the detailed links between fabric, elastic properties, composition, and fault strength remain poorly understood. This gap in information is in part because data are lacking to fully characterize the evolution of gouge microstructures and elastic properties during shearing. Here, we use seismic wave propagation to probe gouge ultrasonic and elastic properties, as a proxy for the development of shear fabrics. We report on a suite of direct shear experiments that include ultrasonic wave transmission to monitor compressional and shear wave velocities (Vp, Vs), during progressive shear of synthetic, clay-rich fault gouge. In order to better understand when and how clay grain alignment and nano-coatings begin to dominate the affect of shear fabric and local gouge density on elastic properties and shear strength, we studied a suite of synthetic gouges composed of Ca-montmorillonite and quartz ranging from 0-100% clay. Our laboratory experiments document friction coefficients (μ) ranging from 0.21 for gouges composed of 100% smectite to 0.62 for 100% quartz, with μ decreasing as clay content increases. We find that Vp and Vs increases as shear progresses and porosity decreases. Ongoing analyses of ultrasonic waves will assess variations of Vp, Vs, and elastic moduli throughout shear and as a function of gouge composition. We anticipate that these variations will be linked to formation of fabric elements observed via microstructural analysis, and will be indicative of whether quartz or clay is dominating how the fabrics form. Finally, we expect that clay content will be the dominant factor controlling shear fabric evolution and, consequently, the key control on the evolution of elastic properties with shear.

Blocky inversion of multichannel elastic impedance for elastic parameters

Science.gov (United States)

Mozayan, Davoud Karami; Gholami, Ali; Siahkoohi, Hamid Reza

2018-04-01

Petrophysical description of reservoirs requires proper knowledge of elastic parameters like P- and S-wave velocities (Vp and Vs) and density (ρ), which can be retrieved from pre-stack seismic data using the concept of elastic impedance (EI). We propose an inversion algorithm which recovers elastic parameters from pre-stack seismic data in two sequential steps. In the first step, using the multichannel blind seismic inversion method (exploited recently for recovering acoustic impedance from post-stack seismic data), high-resolution blocky EI models are obtained directly from partial angle-stacks. Using an efficient total-variation (TV) regularization, each angle-stack is inverted independently in a multichannel form without prior knowledge of the corresponding wavelet. The second step involves inversion of the resulting EI models for elastic parameters. Mathematically, under some assumptions, the EI's are linearly described by the elastic parameters in the logarithm domain. Thus a linear weighted least squares inversion is employed to perform this step. Accuracy of the concept of elastic impedance in predicting reflection coefficients at low and high angles of incidence is compared with that of exact Zoeppritz elastic impedance and the role of low frequency content in the problem is discussed. The performance of the proposed inversion method is tested using synthetic 2D data sets obtained from the Marmousi model and also 2D field data sets. The results confirm the efficiency and accuracy of the proposed method for inversion of pre-stack seismic data.

Moisture Comfort and Antibacterial Properties of Elastic Warp-Knitted Fabrics

Directory of Open Access Journals (Sweden)

Yu Zhi-Cai

2015-03-01

Full Text Available Multifunction elastic warp-knitted fabrics were fabricated on a crochet machine with the use of metal composite yarns/viscose yarn and bamboo polyester/ crisscross-section polyester hybrid yarns as the front face and back face of the knitted fabric structure, respectively. We investigated the effect of the blend ratio of bamboo charcoal/ crisscross-section polyester multiply yarns on the fabric's moisture comfort properties, such as water vapour transmission (WVT, water evaporation rate (WER, and water absorbency. The results showed that blending ratio significantly influenced WVT and WER. Moreover, antibacterial activity of the elastic warp- knitted fabric was tested against Staphylococcus aureus and Escherichia coli in accordance with AATCC 90-2011. Finally, the extension- stress value curves were used to analyse the elastic stretching property, and the fabric exhibited greater breaking elongation and lower stress value in the walewise than in the weft direction.

Computational Elastic Knots

KAUST Repository

Zhao, Xin

2013-01-01

Elastic rods have been studied intensively since the 18th century. Even now the theory of elastic rods is still developing and enjoying popularity in computer graphics and physical-based simulation. Elastic rods also draw attention from architects

Short- and long-run elasticities of electricity demand in the Korean service sector

International Nuclear Information System (INIS)

Lim, Kyoung-Min; Lim, Seul-Ye; Yoo, Seung-Hoon

2014-01-01

This paper attempts to examine the electricity demand function in the Korean service sector using the annual data covering the period 1970–2011. The short- and long-run elasticities of electricity demand with respect to price and income are empirically estimated using a co-integration and error-correction model. The short- and long-run price elasticities are estimated to be −0.421 and −1.002, respectively. The short- and long-run income elasticities are computed to be 0.855 and 1.090, respectively. Electricity demand in the service sector is inelastic to changes in both price and income in the short-run, but elastic in the long-run. Therefore, it appears that a pricing policy is more effective than the direct regulation of reducing electricity demand in the long-run in order to stabilize the electricity demand in the service sector. Moreover, it is necessary to encourage a more efficient use of electricity to cope with increasing demand for electricity following economic growth because the electricity demand in the service sector is income-elastic in the long-run. - Highlights: • We examine the electricity demand function in the Korean service sector. • We use the annual data covering the period 1970–2011. • The demand function is estimated using a co-integration and error-correction model. • The short- and long-run price elasticities are −0.421 and −1.002, respectively. • The short- and long-run income elasticities are 0.855 and 1.090, respectively

Evaluation of Shielding Performance for Newly Developed Composite Materials

Science.gov (United States)

Evans, Beren Richard

This work details an investigation into the contributing factors behind the success of newly developed composite neutron shield materials. Monte Carlo simulation methods were utilized to assess the neutron shielding capabilities and secondary radiation production characteristics of aluminum boron carbide, tungsten boron carbide, bismuth borosilicate glass, and Metathene within various neutron energy spectra. Shielding performance and secondary radiation data suggested that tungsten boron carbide was the most effective composite material. An analysis of the macroscopic cross-section contributions from constituent materials and interaction mechanisms was then performed in an attempt to determine the reasons for tungsten boron carbide's success over the other investigated materials. This analysis determined that there was a positive correlation between a non-elastic interaction contribution towards a material's total cross-section and shielding performance within the thermal and epi-thermal energy regimes. This finding was assumed to be a result of the boron-10 absorption reaction. The analysis also determined that within the faster energy regions, materials featuring higher non-elastic interaction contributions were comparable to those exhibiting primarily elastic scattering via low Z elements. This allowed for the conclusion that composite shield success within higher energy neutron spectra does not necessitate the use elastic scattering via low Z elements. These findings suggest that the inclusion of materials featuring high thermal absorption properties is more critical to composite neutron shield performance than the presence of constituent materials more inclined to maximize elastic scattering energy loss.

Theory-Guided Materials Design of Multi-Phase Ti-Nb Alloys with Bone-Matching Elastic Properties

Directory of Open Access Journals (Sweden)

Jörg Neugebauer

2012-10-01

Full Text Available We present a scale-bridging approach for modeling the integral elasticresponse of polycrystalline composite that is based on a multi-disciplinary combination of(i parameter-free first-principles calculations of thermodynamic phase stability andsingle-crystal elastic stiffness; and (ii homogenization schemes developed forpolycrystalline aggregates and composites. The modeling is used as a theory-guidedbottom-up materials design strategy and applied to Ti-Nb alloys as promising candidatesfor biomedical implant applications. The theoretical results (i show an excellent agreementwith experimental data and (ii reveal a decisive influence of the multi-phase character ofthe polycrystalline composites on their integral elastic properties. The study shows thatthe results based on the density functional theory calculations at the atomistic level canbe directly used for predictions at the macroscopic scale, effectively scale-jumping severalorders of magnitude without using any empirical parameters.

Bilateral Trade Elasticity of Serbia: Is There a J-Curve Effect?

Directory of Open Access Journals (Sweden)

Safet Kurtovic

2017-06-01

Full Text Available We assess the bilateral elasticity effect of real exchange rate depreciation on the export and import demand functions of Serbia and its nine leading trade partners. Analysing quarterly data for the 2004-2015 period, we find the presence of a J-curve effect in the cases of Germany, Austria and Croatia. In contrast, we find that the Marshall-Lerner conditions are fulfilled in the case of bilateral trade with Austria. Finally, in our estimates the elasticity to income has a greater impact on the export and import demand functions than the elasticity to the exchange rate. JEL Classification: F14, F31, F32

A high-order boundary integral method for surface diffusions on elastically stressed axisymmetric rods.

Science.gov (United States)

Li, Xiaofan; Nie, Qing

2009-07-01

Many applications in materials involve surface diffusion of elastically stressed solids. Study of singularity formation and long-time behavior of such solid surfaces requires accurate simulations in both space and time. Here we present a high-order boundary integral method for an elastically stressed solid with axi-symmetry due to surface diffusions. In this method, the boundary integrals for isotropic elasticity in axi-symmetric geometry are approximated through modified alternating quadratures along with an extrapolation technique, leading to an arbitrarily high-order quadrature; in addition, a high-order (temporal) integration factor method, based on explicit representation of the mean curvature, is used to reduce the stability constraint on time-step. To apply this method to a periodic (in axial direction) and axi-symmetric elastically stressed cylinder, we also present a fast and accurate summation method for the periodic Green's functions of isotropic elasticity. Using the high-order boundary integral method, we demonstrate that in absence of elasticity the cylinder surface pinches in finite time at the axis of the symmetry and the universal cone angle of the pinching is found to be consistent with the previous studies based on a self-similar assumption. In the presence of elastic stress, we show that a finite time, geometrical singularity occurs well before the cylindrical solid collapses onto the axis of symmetry, and the angle of the corner singularity on the cylinder surface is also estimated.

Sectoral electricity elasticities in South Africa: Before and after the supply crisis of 2008

Directory of Open Access Journals (Sweden)

James Blignaut

2015-09-01

Full Text Available In this paper, we estimate the price elasticity of electricity for various industrial sectors of the South African economy from 2002 to 2011. The data used include sectoral electricity consumption data and electricity tariff data, both courtesy of Eskom as well as output data based on national statistics. The most important contribution this paper makes is that it includes the period after the sharp rises in electricity tariffs in 2007/2008 following a period of load-shedding and insecurity in electricity supply. Previous studies have included data only until 2007 and, for the most part, have found statistically insignificant, positive elasticities. However, for the period post-2007, we found statistically significant and negative elasticities for 9 of the 11 sectors considered. Our results show that the majority of industrial sectors have become much more sensitive to changes in the price of electricity following 2007/2008, indicating to policymakers that tariff restructuring might influence consumer behaviour significantly.

Investigation on the elastic properties of Gd-Sc-Al garnet by the Mandelstam-Brillouin light scattering method

International Nuclear Information System (INIS)

Zharikov, E.V.; Zagumennyj, A.I.; Kitaeva, V.F.; Lutts, G.B.; Terskov, D.B.

1991-01-01

The Gd-Sc-Al garnet (GSAG) crystals grown from the melt with composition Gd 2.88 Sc 1.89 Al 3.23 O 12 , were investigated. The GSAG doped with chromium was also studied. The Mandelstam-Brillouin (MB) light scattering in the GSAG crystals was observed. The garnet elastic components were determined using the data on the MB component shifts, the products of the elastic constants by molar volume were calculated as well. The GSAG is elastically anisotropic. The doping addition introduction do not cause noticeable change in the elastic properties. The obtained values of elastic constants and their combinations for GSAG were compared with the data for aluminium and gallium garnets. The comparison has shown that the values of elastic constants for GSAG is closer to those for Gd-Sc-Ga garnet than to the corresponding values for the Y-Al one

Magneto-Induced ac Electrical Permittivity of Metal-Dielectric Composites with a Two Characteristic Length Scales Periodic Microstructure

International Nuclear Information System (INIS)

Strelniker, Y.M.; Bergman, D.J.

1998-01-01

A new effect was recently predicted in conducting composites that have a periodic microstructure: an induced strongly anisotropic dc magneto-resistance. This phenomenon is already verified on high mobility n-GaAs films. Here we discuss the possibility of observing analogous behavior in the ac electric permittivity of a metal-dielectric composite with a periodic microstructure in the presence of a strong magnetic field. We developed new analytical and numerical methods to treat the low-frequency magneto-optical properties in composite media with both disordered and periodic conducting micro-structures. Those methods allow us to study composites with inclusions of arbitrary shape (and arbitrary volume fraction) at arbitrarily strong magnetic field. This is exploited in order to calculate an effective dielectric tensor for this system as a function of applied magnetic field and ac frequency. We show that in a non-dilute metal-dielectric composite medium the magneto-plasma resonance and the cyclotron resonance depend upon both the applied magnetic field as well as on the geometric shape of the inclusion. Near such a resonance, it is possible to achieve large values for the ratio of the off-diagonal-to-diagonal electric permittivity tensor components, ε xy /ε xx , (since ε xx →0, while ε xy ≠0), which is analogous to similar ratio of the resistivity tensor components, ρ xy /ρ xx , in the case of dc magneto-transport problem. Motivated by this observation and by results of previous studies of dc magneto-transport in composite conductors, we then performed a numerical study of the ac magneto-electric properties of a particular metal-dielectric composite film with a periodic columnar microstructure which has a two characteristic length scales. The unit cell of such composite is prepared as follows: We placed the conducting square (in cross section) rods (first characteristic length scale) along the perimeter of the unit cell in order to create a dielectric host

Remaking the Elasticity of Consumer Wants

DEFF Research Database (Denmark)

Pallesen, Trine; Jenle, Rasmus Ploug

The paper analyses a smart grid project named EcoGrid, the paper shows how a large market experiment is used to present a solution to the intermittency problem associated with wind power: How to balance supply and demand when electricity production 'follows the wind'? It is shown how electricity...... consumption is sought moved away from periods of peak consumption, and towards periods of peak production, by making consumers sensitive to ongoing changes in price. The study takes a pragmatic stance, applying concepts from the sociology of markets. The paper shows how the price elasticity of a good...

Aeromechanical stability of helicopters with composite rotor blades in forward flight

Science.gov (United States)

Smith, Edward C.; Chopra, Inderjit

1992-01-01

The aeromechanical stability, including air resonance in hover, air resonance in forward flight, and ground resonance, of a helicopter with elastically tailored composite rotor blades is investigated. Five soft-inplane hingeless rotor configurations, featuring elastic pitch-lag, pitch-flap and extension-torsion couplings, are analyzed. Elastic couplings introduced through tailored composite blade spars can have a powerful effect on both air and ground resonance behavior. Elastic pitch-flap couplings (positive and negative) strongly affect body, rotor and dynamic inflow modes. Air resonance stability is diminished by elastic pitch-flap couplings in hover and forward flight. Negative pitch-lag elastic coupling has a stabilizing effect on the regressive lag mode in hover and forward flight. The negative pitch-lag coupling has a detrimental effect on ground resonance stability. Extension-torsion elastic coupling (blade pitch decreases due to tension) decreases regressive lag mode stability in both airborne and ground contact conditions. Increasing thrust levels has a beneficial influence on ground resonance stability for rotors with pitch-flap and extension-torsion coupling and is only marginally effective in improving stability of rotors with pitch-lag coupling.

Universal composition-structure-property maps for natural and biomimetic platelet-matrix composites and stacked heterostructures.

Science.gov (United States)

Sakhavand, Navid; Shahsavari, Rouzbeh

2015-03-16

Many natural and biomimetic platelet-matrix composites--such as nacre, silk, and clay-polymer-exhibit a remarkable balance of strength, toughness and/or stiffness, which call for a universal measure to quantify this outstanding feature given the structure and material characteristics of the constituents. Analogously, there is an urgent need to quantify the mechanics of emerging electronic and photonic systems such as stacked heterostructures. Here we report the development of a unified framework to construct universal composition-structure-property diagrams that decode the interplay between various geometries and inherent material features in both platelet-matrix composites and stacked heterostructures. We study the effects of elastic and elastic-perfectly plastic matrices, overlap offset ratio and the competing mechanisms of platelet versus matrix failures. Validated by several 3D-printed specimens and a wide range of natural and synthetic materials across scales, the proposed universally valid diagrams have important implications for science-based engineering of numerous platelet-matrix composites and stacked heterostructures.

Determination of hoop direction effective elastic moduli of non-circular profile, fiber reinforced polymer composite sewer liner pipes from lateral ring compression tests

International Nuclear Information System (INIS)

Czél, Gergely; Takács, Dénes

2015-01-01

A new material property determination method is presented for the calculation of effective elastic moduli of non-circular ring specimens cut from filament wound oval profile polymer composite sewer liner pipes. The hoop direction elastic moduli was determined using the test results obtained from ring compression tests, which is a very basic setup, and requires no special equipment. Calculations were executed for many different oval profiles, and diagrams were constructed, from which the cross section dependent C_e_f_f constants can be taken. The new method was validated by the comparison of tests and finite element analysis results. The calculation method and the diagrams are essential design tools for engineers, and a big step forward in sizing non-circular profile liner pipes. - Highlights: • A simple modulus measurement method is presented for non-circular ring specimens. • The evaluation method is validated against a finite element model. • Profile shape dependent constants are presented for a wide range of cross-sections. • A set of charts with the constants are provided to aid design engineers.

Physically elastic analysis of a cylindrical ring as a unit cell of a complete composite under applied stress in the complex plane using cubic polynomials

Science.gov (United States)

Monfared, Vahid

2018-03-01

Elastic analysis is analytically presented to predict the behaviors of the stress and displacement components in the cylindrical ring as a unit cell of a complete composite under applied stress in the complex plane using cubic polynomials. This analysis is based on the complex computation of the stress functions in the complex plane and polar coordinates. Also, suitable boundary conditions are considered and assumed to analyze along with the equilibrium equations and bi-harmonic equation. This method has some important applications in many fields of engineering such as mechanical, civil and material engineering generally. One of the applications of this research work is in composite design and designing the cylindrical devices under various loadings. Finally, it is founded that the convergence and accuracy of the results are suitable and acceptable through comparing the results.

Simulation of Degraded Properties of 2D plain Woven C/SiC Composites under Preloading Oxidation Atmosphere

Science.gov (United States)

Chen, Xihui; Sun, Zhigang; Sun, Jianfen; Song, Yingdong

2017-12-01

In this paper, a numerical model which incorporates the oxidation damage model and the finite element model of 2D plain woven composites is presented for simulation of the oxidation behaviors of 2D plain woven C/SiC composite under preloading oxidation atmosphere. The equal proportional reduction method is firstly proposed to calculate the residual moduli and strength of unidirectional C/SiC composite. The multi-scale method is developed to simulate the residual elastic moduli and strength of 2D plain woven C/SiC composite. The multi-scale method is able to accurately predict the residual elastic modulus and strength of the composite. Besides, the simulated residual elastic moduli and strength of 2D plain woven C/SiC composites under preloading oxidation atmosphere show good agreements with experimental results. Furthermore, the preload, oxidation time, temperature and fiber volume fractions of the composite are investigated to show their influences upon the residual elastic modulus and strength of 2D plain woven C/SiC composites.

Elastic properties of synthetic materials for soft tissue modeling

International Nuclear Information System (INIS)

Mansy, H A; Grahe, J R; Sandler, R H

2008-01-01

Mechanical models of soft tissue are useful for studying vibro-acoustic phenomena. They may be used for validating mathematical models and for testing new equipment and techniques. The objective of this study was to measure density and visco-elastic properties of synthetic materials that can be used to build such models. Samples of nine different materials were tested under dynamic (0.5 Hz) compressive loading conditions. The modulus of elasticity of the materials was varied, whenever possible, by adding a softener during manufacturing. The modulus was measured over a nine month period to quantify the effect of ageing and softener loss on material properties. Results showed that a wide range of the compression elasticity modulus (10 to 1400 kPa) and phase (3.5 0 -16.7 0 ) between stress and strain were possible. Some materials tended to exude softener over time, resulting in a weight loss and elastic properties change. While the weight loss under normal conditions was minimal in all materials (<3% over nine months), loss under accelerated weight-loss conditions can reach 59%. In the latter case an elasticity modulus increase of up to 500% was measured. Key advantages and limitations of candidate materials were identified and discussed

Negative stiffness honeycombs as tunable elastic metamaterials

Science.gov (United States)

Goldsberry, Benjamin M.; Haberman, Michael R.

2018-03-01

Acoustic and elastic metamaterials are media with a subwavelength structure that behave as effective materials displaying atypical effective dynamic properties. These material systems are of interest because the design of their sub-wavelength structure allows for direct control of macroscopic wave dispersion. One major design limitation of most metamaterial structures is that the dynamic response cannot be altered once the microstructure is manufactured. However, the ability to modify wave propagation in the metamaterial with an external stimulus is highly desirable for numerous applications and therefore remains a significant challenge in elastic metamaterials research. In this work, a honeycomb structure composed of a doubly periodic array of curved beams, known as a negative stiffness honeycomb (NSH), is analyzed as a tunable elastic metamaterial. The nonlinear static elastic response that results from large deformations of the NSH unit cell leads to a large variation in linear elastic wave dispersion associated with infinitesimal motion superposed on the externally imposed pre-strain. A finite element model is utilized to model the static deformation and subsequent linear wave motion at the pre-strained state. Analysis of the slowness surface and group velocity demonstrates that the NSH exhibits significant tunability and a high degree of anisotropy which can be used to guide wave energy depending on static pre-strain levels. In addition, it is shown that partial band gaps exist where only longitudinal waves propagate. The NSH therefore behaves as a meta-fluid, or pentamode metamaterial, which may be of use for applications of transformation elastodynamics such as cloaking and gradient index lens devices.

Effect of the porosity induced by the Chemical Vapor Infiltration (CVI) process on the elastic behaviour of SiC/SiC composite materials at the strand scale

International Nuclear Information System (INIS)

Gelebart, L.; Colin, C.

2008-01-01

The aim of this work is to reveal the role of porosity inhering to the CVI fabrication process. Indeed, this process which consists of depositing by a gaseous way a SiC layer on a fibrous preform (assembling weaved of SiC fibers) does not allow a complete densification of the material and induces thus a porosity of size and shape particularly heterogeneous and complex. The effect of this porosity, studied at the strand scale (unidirectional composite) is revealed by the elastic anisotropy of the behaviour as well as by the local stresses distribution heterogeneity inside the strand. A discussion is proposed on the representative elementary volume size associated with this type of microstructures. The method used depends on a generation model of 'representative' microstructures of the microstructures induced by the CVI process. On account of the lack of data on the three-dimensional characterization of the porosity, a microstructure invariance hypothesis in the direction of fibers is used. In order to study the elastic behaviour of these microstructures, a periodic homogenisation process, with stress control, is carried out on these porous microstructures in the finite elements CASTEM calculation code. The obtained results reveals an important elastic anisotropy. In order to reveal the interest of this approach and the requirement to take into account the complex geometry of the porosity, these results are compared to a Mori-Tanaka analytical model frequently used for this type of material. Then is studied the evolution of the heterogeneity of the local stresses, that no analytical model can describe, in term of the type of load. If for a traction direction parallel to fibers, the stresses are homogeneous, a strong heterogeneity appears when the traction direction diverges from the fibers direction. For a solicitation perpendicular to fibers, the stresses distribution reveals a peak with zero stress corresponding to zones unloaded inside the material; a second peak

Improved Mechanical Compatibility and Cytocompatibility of Ta/Ti Double-Layered Composite Coating

Science.gov (United States)

Ding, Ding; Xie, Youtao; Li, Kai; Huang, Liping; Zheng, Xuebin

2017-08-01

In order to improve the mechanical compatibility and cytocompatibility of titanium implants, a composite coating with double layers composed of tantalum and titanium was designed and prepared using plasma spraying technology. In the composite coating, the upper tantalum layer provides a good biocompatibility, and the sublayer of titanium with a porous structure ensures the low elastic modulus. Results show that the fabricated composite coating exhibits a relatively low elastic modulus of 26.7 GPa, which is close to the elastic modulus of human cortical bone. In vitro cytocompatibility evaluation of the composite coating shows that the human bone marrow stromal cells exhibit enhanced adhesion and spreading performance on the double-layered composite coating in comparison with the single-layered titanium coating. In order to eliminate the misgivings of chemical stability of the composite coating in clinical application, electrochemical corrosion of the coating was examined. The results obtained revealed a very weak galvanic corrosion between the tantalum and titanium in the composite coating, which would ensure the safety of the coating in vivo.

Stressed-deformed state of mountain rocks in elastic stage and between elasticity

Directory of Open Access Journals (Sweden)

Samedov A.M.

2017-12-01

Full Text Available The problems of the stress-strain state of rocks in the elastic stage and beyond the elastic limits, and the ways of schematizing the tension and compression diagrams were reviewed in the article. To simplify calculations outside the elastic range, the tension (compression diagrams are usually schematized, i.e. are replaced by curved smooth lines having a fairly simple mathematical expression and at the same time well coinciding with the experimentally obtained diagrams. When diagram is to be schematized, it is necessary to take a constant temperature of superheated water steam if a rock test is planned in a relaxed form. Note that when the diagram is schematizing, the difference between the limits of proportionality and fluidity is erased. This allows the limit of proportionality to be considered the limit of fluidity. Schematicization can be carried out in the area where the tensile strength (compression is planned to be destroyed with the established weakening of rocks by exposure to water steam or chemical reagents. Samples of rocks in natural form were tested and weakened by means of superheated water steam (220 °C and more and chemical reagents for tension and compression. The data are obtained, the diagrams of deformation are constructed and schematized in the elastic stage and beyond the elastic limit. Based on the schematic diagrams of deformation, the components of stress and strain were composed in the elastic stage and beyond the elastic limit. It is established in the publication that rocks under compression and stretching deform, both within the elastic stage, and beyond the limits of elasticity. This could be seen when the samples, both in natural and in weakened state, with superheated water steam (more than 220 °C or chemical reagents were tested. In their natural form, they are mainly deformed within the elastic stage and are destroyed as a brittle material, and in a weakened form they can deform beyond the elastic stage and

Elastic-plastic collapse of super-elastic shock waves in face-centered-cubic solids

International Nuclear Information System (INIS)

Zhakhovsky, Vasily V; Demaske, Brian J; Oleynik, Ivan I; Inogamov, Nail A; White, Carter T

2014-01-01

Shock waves in the [110] and [111] directions of single-crystal Al samples were studied using molecular dynamics (MD) simulations. Piston-driven simulations were performed to investigate the split shock-wave regime. At low piston velocities, the material is compressed initially to a metastable over-compressed elastic state leading to a super-elastic single shock wave. This metastable elastic state later collapses to a plastic state resulting in the formation of a two-wave structure consisting of an elastic precursor followed by a slower plastic wave. The single two-zone elastic-plastic shock-wave regime appearing at higher piston velocities was studied using moving window MD. The plastic wave attains the same average speed as the elastic precursor to form a single two-zone shock wave. In this case, repeated collapse of the highly over-compressed elastic state near the plastic shock front produces ultrashort triangle pulses that provide the pressure support for the leading elastic precursor.

Periodicity effects of axial waves in elastic compound rods

DEFF Research Database (Denmark)

Nielsen, R. B.; Sorokin, S. V.

2015-01-01

Floquet analysis is applied to the Bernoulli-Euler model for axial waves in a periodic rod. Explicit asymptotic formulae for the stop band borders are given and the topology of the stop band pattern is explained. Eigenfrequencies of the symmetric unit cell are determined by the Phase-closure Prin......Floquet analysis is applied to the Bernoulli-Euler model for axial waves in a periodic rod. Explicit asymptotic formulae for the stop band borders are given and the topology of the stop band pattern is explained. Eigenfrequencies of the symmetric unit cell are determined by the Phase......-closure Principle, and their correspondence with stop band formation is shown. Steady-state and transient dynamics of a periodic rod of finite length are analysed numerically and the difference in structural response when excitation is done in either stop- or pass bands is demonstrated. A physical interpretation...

Photoproduction of J/{psi} mesons at medium and low elasticities at HERA

Energy Technology Data Exchange (ETDEWEB)

Salvaire, F.

2007-09-15

The first analysis of inelastic J/{psi} meson production in photoproduction (Q{sup 2}<2.5 GeV{sup 2}) of the H1 experiment for the second phase of HERA (HERA II) is presented. The analysis is carried out at low and medium elasticities. The production of heavy quarks (charm, or bottom) is of special interest since the mass of the quarks provides a hard scale for the application of perturbative QCD. The muonic decay channel is used to select the J/{psi} mesons. The data was collected by the H1 detector during the period 2003-2005, and corresponds to an integrated luminosity of 133 pb{sup -1}. However only a subset of this data could be analysed. At the start of HERA II the trigger system was affected by a sizeable background. Then a fault was introduced in the trigger software during the summer 2004 and was only discovered and solved in April 2006. This means that approximately 80 % of the triggered events at medium elasticities and 65 % at low elasticities was lost during this period. Moreover during the first half of 2005 the muon trigger was affected by faulty power supplies. Consequently two good data taking periods are analysed: a first period with an integrated luminosity of 23 pb{sup -1} collected in 2004, and a second period of 60 pb{sup -1} collected during the second half of 2005, which is however strongly affected by the malfunction of the trigger software. In the medium elasticity region the total photoproduction cross section as a function of the photon-proton centre-of-mass energy W and the single differential cross sections as functions of the transverse momentum squared of the J/{psi} meson Pt{sup 2}{sub t,{psi}} and the elasticity z are extracted. The analysis covers the kinematic range 0.3{<=}z{<=}0.9, 60{<=}W{sub {gamma}}{sub p}{<=}240 GeV, and Pt{sup 2}{sub t,{psi}}>1 GeV{sup 2}. The same analysis is performed at low elasticity for the kinematic region 0.05{<=}z{<=}0.45, 120{<=}W{sub {gamma}}{sub p}{<=}260 GeV, and Pt{sup 2}{sub t,{psi}}>1 Ge

Study of a Piezo-Thermo-Elastic Materials Console

Directory of Open Access Journals (Sweden)

hamza madjid berrabah

2015-09-01

Full Text Available In the first part of this work, analytical expressions were determined for the stresses through the thickness of a composite beam submitted to electrical excitation. In the second part of this study we are interested in the theory of elasticity, which is used to obtain exact solutions of piezo-thermo-elastic consoles gradually coupled evaluated under different loads. These solutions are used to identify the piezoelectric parameter and thermal coefficients of the materials. In addition, numerical results are obtained for the analysis of the loaded console by two different types of loading. In this study we show also that changing the linear thermal parameters of the material does not affect the distribution of the stress and the induction of the beam. However it affetcs the components of the deformation, electric field, the displacement and the electric potential of the console.

Elastic scattering and quasi-elastic transfers

International Nuclear Information System (INIS)

Mermaz, M.C.

1978-01-01

Experiments are presented which it will be possible to carry out at GANIL on the elastic scattering of heavy ions: diffraction phenomena if the absorption is great, refraction phenomena if absorption is low. The determination of the optical parameters can be performed. The study of the quasi-elastic transfer reactions will make it possible to know the dynamics of the nuclear reactions, form exotic nuclei and study their energy excitation spectrum, and analyse the scattering and reaction cross sections [fr

THz elastic dynamics in finite-size CoFeB-MgO phononic superlattices

Energy Technology Data Exchange (ETDEWEB)

Ulrichs, Henning, E-mail: hulrich@gwdg.de; Meyer, Dennis; Müller, Markus; Wittrock, Steffen; Mansurova, Maria [I. Physical Institute, Georg-August University of Göttingen, Friedrich-Hund-Platz 1, 37077 Göttingen (Germany); Walowski, Jakob; Münzenberg, Markus [Institute of Physics, Ernst-Moritz-Arndt University of Greifswald, Felix-Hausdorff-Str. 6, 17489 Greifswald (Germany)

2016-10-14

In this article, we present the observation of coherent elastic dynamics in a nano-scale phononic superlattice, which consists of only 4 bilayers. We demonstrate how ultra-short light pulses with a length of 40 fs can be utilized to excite a coherent elastic wave at 0.535 THz, which persist over about 20 ps. In later steps of the elastic dynamics, modes with frequency of 1.7 THz and above appear. All these modes are related to acoustic band gaps. Thus, the periodicity strongly manifests in the wave physics, although the system under investigation has only a small number of spatial periods. To further illustrate this, we show how by breaking the translational invariance of the superlattice, these features can be suppressed. Discussed in terms of phonon blocking and radiation, we elucidate in how far our structures can be considered as useful building blocks for phononic devices.

Price elasticity of natural gas demand in the power generation sector

International Nuclear Information System (INIS)

McArdle, P.F.

1990-01-01

Today, the demand for energy by the electric generation sector is highly competitive and price-responsive. Previous estimates of the price elasticity of natural gas demand in this sector have focused primarily on data from the 1960s and 1970s. Such estimates fail to take full account of economic, regulatory, and legislative developments that have altered the structure of the electric generation market during the 1980s. Structural changes include an increased ability of utilities to choose among generating options, the increase in non-utility generators, the amending of the Fuel Use Act, and a more competitive market for electricity. An accurate estimate of price elasticity requires a refocusing on data from the post-1983 period. The purpose of this paper is to answer two questions: how price responsive (elastic) is natural gas demand in this market; and what changes in natural gas demand elasticity have occurred over time

Short-Run and Long-Run Elasticities of Diesel Demand in Korea

Directory of Open Access Journals (Sweden)

Seung-Hoon Yoo

2012-11-01

Full Text Available This paper investigates the demand function for diesel in Korea covering the period 1986–2011. The short-run and long-run elasticities of diesel demand with respect to price and income are empirically examined using a co-integration and error-correction model. The short-run and long-run price elasticities are estimated to be −0.357 and −0.547, respectively. The short-run and long-run income elasticities are computed to be 1.589 and 1.478, respectively. Thus, diesel demand is relatively inelastic to price change and elastic to income change in both the short-run and long-run. Therefore, a demand-side management through raising the price of diesel will be ineffective and tightening the regulation of using diesel more efficiently appears to be more effective in Korea. The demand for diesel is expected to continuously increase as the economy grows.

Nonlinear elastic waves in materials

CERN Document Server

Rushchitsky, Jeremiah J

2014-01-01

The main goal of the book is a coherent treatment of the theory of propagation in materials of nonlinearly elastic waves of displacements, which corresponds to one modern line of development of the nonlinear theory of elastic waves. The book is divided on five basic parts: the necessary information on waves and materials; the necessary information on nonlinear theory of elasticity and elastic materials; analysis of one-dimensional nonlinear elastic waves of displacement – longitudinal, vertically and horizontally polarized transverse plane nonlinear elastic waves of displacement; analysis of one-dimensional nonlinear elastic waves of displacement – cylindrical and torsional nonlinear elastic waves of displacement; analysis of two-dimensional nonlinear elastic waves of displacement – Rayleigh and Love nonlinear elastic surface waves. The book is addressed first of all to people working in solid mechanics – from the students at an advanced undergraduate and graduate level to the scientists, professional...

Modeled and Measured Dynamics of a Composite Beam with Periodically Varying Foam Core

Science.gov (United States)

Cabell, Randolph H.; Cano, Roberto J.; Schiller, Noah H.; Roberts Gary D.

2012-01-01

The dynamics of a sandwich beam with carbon fiber composite facesheets and foam core with periodic variations in material properties are studied. The purpose of the study is to compare finite element predictions with experimental measurements on fabricated beam specimens. For the study, three beams were fabricated: one with a compliant foam core, a second with a stiffer core, and a third with the two cores alternating down the length of the beam to create a periodic variation in properties. This periodic variation produces a bandgap in the frequency domain where vibrational energy does not readily propagate down the length of the beam. Mode shapes and natural frequencies are compared, as well as frequency responses from point force input to velocity response at the opposite end of the beam.

Optical properties of spontaneous lateral composition modulation in AlAs/InAs short-period superlattices

International Nuclear Information System (INIS)

Francoeur, S.; Zhang, Yong; Norman, A. G.; Alsina, F.; Mascarenhas, A.; Reno, J. L.; Jones, E. D.; Lee, S. R.; Follstaedt, D. M.

2000-01-01

The effect of lateral composition modulation, spontaneously generated during the epitaxial growth of an AlAs/InAs short-period superlattice, on the electronic band structure is investigated using phototransmission and photoluminescence spectroscopy. Compared with uniform layers of identical average composition, the presence of the composition modulation considerably reduces the band-gap energy and produces strongly polarized emission and absorption spectra. We demonstrate that the dominant polarization direction can selectively be aligned along the [1(bar sign)10] or [010] crystallographic directions. In compressively strained samples, the use of (001) InP substrates slightly miscut toward (111)A or (101) resulted in modulation directions along [110] or [100], respectively, and dominant polarization directions along a direction orthogonal to the respective composition modulation. Band-gap reductions as high as 350 and 310 meV are obtained for samples with composition modulation along [110] and [100], respectively. Ratios of polarized intensities up to 26 are observed in transmission spectra. (c) 2000 American Institute of Physics

Galactic Cosmic-Ray Energy Spectra and Composition during the 2009-2010 Solar Minimum Period

Science.gov (United States)

Lave, K. A.; Wiedenbeck, Mark E.; Binns, W. R.; Christian, E. R.; Cummings, A. C.; Davis, A. J.; deNolfo, G. A.; Israel, M. H..; Leske, R. A.; Mewaldt, R. A.;

Size-dependent elastic moduli and vibrational properties of fivefold twinned copper nanowires

Science.gov (United States)

Zheng, Y. G.; Zhao, Y. T.; Ye, H. F.; Zhang, H. W.

2014-08-01

Based on atomistic simulations, the elastic moduli and vibration behaviors of fivefold twinned copper nanowires are investigated in this paper. Simulation results show that the elastic (i.e., Young’s and shear) moduli exhibit size dependence due to the surface effect. The effective Young’s modulus is found to decrease slightly whereas the effective shear modulus increases slightly with the increase in the wire radius. Both moduli tend to approach certain values at a larger radius and can be suitably described by core-shell composite structure models. Furthermore, we show by comparing simulation results and continuum predictions that, provided the effective Young’s and shear moduli are used, classic elastic theory can be applied to describe the small-amplitude vibration of fivefold twinned copper nanowires. Moreover, for the transverse vibration, the Timoshenko beam model is more suitable because shear deformation becomes apparent.

Size-dependent elastic moduli and vibrational properties of fivefold twinned copper nanowires

International Nuclear Information System (INIS)

Zheng, Y G; Zhao, Y T; Ye, H F; Zhang, H W

2014-01-01

Based on atomistic simulations, the elastic moduli and vibration behaviors of fivefold twinned copper nanowires are investigated in this paper. Simulation results show that the elastic (i.e., Young’s and shear) moduli exhibit size dependence due to the surface effect. The effective Young’s modulus is found to decrease slightly whereas the effective shear modulus increases slightly with the increase in the wire radius. Both moduli tend to approach certain values at a larger radius and can be suitably described by core-shell composite structure models. Furthermore, we show by comparing simulation results and continuum predictions that, provided the effective Young’s and shear moduli are used, classic elastic theory can be applied to describe the small-amplitude vibration of fivefold twinned copper nanowires. Moreover, for the transverse vibration, the Timoshenko beam model is more suitable because shear deformation becomes apparent. (paper)

Numerical simulation of elasto-plastic deformation of composites: evolution of stress microfields and implications for homogenization models

Science.gov (United States)

González, C.; Segurado, J.; LLorca, J.

2004-07-01

The deformation of a composite made up of a random and homogeneous dispersion of elastic spheres in an elasto-plastic matrix was simulated by the finite element analysis of three-dimensional multiparticle cubic cells with periodic boundary conditions. "Exact" results (to a few percent) in tension and shear were determined by averaging 12 stress-strain curves obtained from cells containing 30 spheres, and they were compared with the predictions of secant homogenization models. In addition, the numerical simulations supplied detailed information of the stress microfields, which was used to ascertain the accuracy and the limitations of the homogenization models to include the nonlinear deformation of the matrix. It was found that secant approximations based on the volume-averaged second-order moment of the matrix stress tensor, combined with a highly accurate linear homogenization model, provided excellent predictions of the composite response when the matrix strain hardening rate was high. This was not the case, however, in composites which exhibited marked plastic strain localization in the matrix. The analysis of the evolution of the matrix stresses revealed that better predictions of the composite behavior can be obtained with new homogenization models which capture the essential differences in the stress carried by the elastic and plastic regions in the matrix at the onset of plastic deformation.

Investigation of structural, electronic and anisotropic elastic properties of Ru-doped WB{sub 2} compound by increased valence electron concentration

Energy Technology Data Exchange (ETDEWEB)

Surucu, Gokhan, E-mail: g_surucu@yahoo.com [Ahi Evran University, Department of Electric and Energy, 40100, Kirsehir (Turkey); Gazi University, Photonics Application and Research Center, 06500, Ankara (Turkey); Kaderoglu, Cagil [Ankara University, Department of Engineering Physics, 06100, Ankara (Turkey); Deligoz, Engin; Ozisik, Haci [Aksaray University, Department of Physics, 68100, Aksaray (Turkey)

2017-03-01

First principles density functional theory (DFT) calculations have been used to investigate the structural, anisotropic elastic and electronic properties of ruthenium doped tungsten-diboride ternary compounds (W{sub 1−x}Ru{sub x}B{sub 2}) for an increasing molar fraction of Ru atom from 0.1 to 0.9 by 0.1. Among the nine different compositions, W{sub 0.3}Ru{sub 0.7}B{sub 2} has been found as the most stable one due to the formation energy and band filling theory calculations. Moreover, the band structures and partial density of states (PDOS) have been computed for each x composition. After obtaining the elastic constants for all x compositions, the secondary results such as Bulk modulus, Young’s modulus, Poisson’s ratio, Shear modulus, and Vickers Hardness of polycrystalline aggregates have been derived and the relevant mechanical properties have been discussed. In addition, the elastic anisotropy has been visualized in detail by plotting the directional dependence of compressibility, Poisson ratio, Young’s and Shear moduli. - Highlights: • Effects of Ru substitution in WB{sub 2} using increased valence electron concentration. • Structural, electronic, mechanic and elastic properties for increasing Ru content. • Considered alloys are incompressible, brittle, stiffer and high hard materials.

Relationship between swelling and elastic properties in neutron-irradiated 316 stainless steel

International Nuclear Information System (INIS)

Bates, J.F.

1976-04-01

The results encompass elastic property measurements on several alloys, which differ in silicon, molybdenum and phosphorus contents but have a nominal 316 stainless steel composition. It is shown that there is a good correlation between the initial shear modulus of the material and the resultant swelling rate of that material. It is also shown that the bias factor concept does not satisfactorily account for the observed compositional sensitivity of swelling in the alloys investigated. 6 fig

One-Dimensional Mass-Spring Chains Supporting Elastic Waves with Non-Conventional Topology

Directory of Open Access Journals (Sweden)

2016-04-01

Full Text Available There are two classes of phononic structures that can support elastic waves with non-conventional topology, namely intrinsic and extrinsic systems. The non-conventional topology of elastic wave results from breaking time reversal symmetry (T-symmetry of wave propagation. In extrinsic systems, energy is injected into the phononic structure to break T-symmetry. In intrinsic systems symmetry is broken through the medium microstructure that may lead to internal resonances. Mass-spring composite structures are introduced as metaphors for more complex phononic crystals with non-conventional topology. The elastic wave equation of motion of an intrinsic phononic structure composed of two coupled one-dimensional (1D harmonic chains can be factored into a Dirac-like equation, leading to antisymmetric modes that have spinor character and therefore non-conventional topology in wave number space. The topology of the elastic waves can be further modified by subjecting phononic structures to externally-induced spatio-temporal modulation of their elastic properties. Such modulations can be actuated through photo-elastic effects, magneto-elastic effects, piezo-electric effects or external mechanical effects. We also uncover an analogy between a combined intrinsic-extrinsic systems composed of a simple one-dimensional harmonic chain coupled to a rigid substrate subjected to a spatio-temporal modulation of the side spring stiffness and the Dirac equation in the presence of an electromagnetic field. The modulation is shown to be able to tune the spinor part of the elastic wave function and therefore its topology. This analogy between classical mechanics and quantum phenomena offers new modalities for developing more complex functions of phononic crystals and acoustic metamaterials.

Viscous-elastic dynamics of power-law fluids within an elastic cylinder

Science.gov (United States)

Boyko, Evgeniy; Bercovici, Moran; Gat, Amir D.

2017-07-01

In a wide range of applications, microfluidic channels are implemented in soft substrates. In such configurations, where fluidic inertia and compressibility are negligible, the propagation of fluids in channels is governed by a balance between fluid viscosity and elasticity of the surrounding solid. The viscous-elastic interactions between elastic substrates and non-Newtonian fluids are particularly of interest due to the dependence of viscosity on the state of the system. In this work, we study the fluid-structure interaction dynamics between an incompressible non-Newtonian fluid and a slender linearly elastic cylinder under the creeping flow regime. Considering power-law fluids and applying the thin shell approximation for the elastic cylinder, we obtain a nonhomogeneous p-Laplacian equation governing the viscous-elastic dynamics. We present exact solutions for the pressure and deformation fields for various initial and boundary conditions for both shear-thinning and shear-thickening fluids. We show that in contrast to Stokes' problem where a compactly supported front is obtained for shear-thickening fluids, here the role of viscosity is inversed and such fronts are obtained for shear-thinning fluids. Furthermore, we demonstrate that for the case of a step in inlet pressure, the propagation rate of the front has a tn/n +1 dependence on time (t ), suggesting the ability to indirectly measure the power-law index (n ) of shear-thinning liquids through measurements of elastic deformation.

ElasticSearch cookbook

CERN Document Server

Paro, Alberto

2013-01-01

Written in an engaging, easy-to-follow style, the recipes will help you to extend the capabilities of ElasticSearch to manage your data effectively.If you are a developer who implements ElasticSearch in your web applications, manage data, or have decided to start using ElasticSearch, this book is ideal for you. This book assumes that you've got working knowledge of JSON and Java

Elasticity Theory Solution of the Problem on Plane Bending of a Narrow Layered Cantilever Beam by Loads at Its Free End

Science.gov (United States)

Goryk, A. V.; Koval'chuk, S. B.

2018-05-01

An exact elasticity theory solution for the problem on plane bending of a narrow layered composite cantilever beam by tangential and normal loads distributed on its free end is presented. Components of the stress-strain state are found for the whole layers package by directly integrating differential equations of the plane elasticity theory problem by using an analytic representation of piecewise constant functions of the mechanical characteristics of layer materials. The continuous solution obtained is realized for a four-layer beam with account of kinematic boundary conditions simulating the rigid fixation of its one end. The solution obtained allows one to predict the strength and stiffness of composite cantilever beams and to construct applied analytical solutions for various problems on the elastic bending of layered beams.

Calculation of elastic-plastic strain ranges for fatigue analysis based on linear elastic stresses

International Nuclear Information System (INIS)

Sauer, G.

1998-01-01

Fatigue analysis requires that the maximum strain ranges be known. These strain ranges are generally computed from linear elastic analysis. The elastic strain ranges are enhanced by a factor K e to obtain the total elastic-plastic strain range. The reliability of the fatigue analysis depends on the quality of this factor. Formulae for calculating the K e factor are proposed. A beam is introduced as a computational model for determining the elastic-plastic strains. The beam is loaded by the elastic stresses of the real structure. The elastic-plastic strains of the beam are compared with the beam's elastic strains. This comparison furnishes explicit expressions for the K e factor. The K e factor is tested by means of seven examples. (orig.)

Elastic properties of woven bone: effect of mineral content and collagen fibrils orientation.

Science.gov (United States)

García-Rodríguez, J; Martínez-Reina, J

2017-02-01

Woven bone is a type of tissue that forms mainly during fracture healing or fetal bone development. Its microstructure can be modeled as a composite with a matrix of mineral (hydroxyapatite) and inclusions of collagen fibrils with a more or less random orientation. In the present study, its elastic properties were estimated as a function of composition (degree of mineralization) and fibril orientation. A self-consistent homogenization scheme considering randomness of inclusions' orientation was used for this purpose. Lacuno-canalicular porosity in the form of periodically distributed void inclusions was also considered. Assuming collagen fibrils to be uniformly oriented in all directions led to an isotropic tissue with a Young's modulus [Formula: see text] GPa, which is of the same order of magnitude as that of woven bone in fracture calluses. By contrast, assuming fibrils to have a preferential orientation resulted in a Young's modulus in the preferential direction of 9-16 GPa depending on the mineral content of the tissue. These results are consistent with experimental evidence for woven bone in foetuses, where collagen fibrils are aligned to a certain extent.

From Process Modeling to Elastic Property Prediction for Long-Fiber Injection-Molded Thermoplastics

International Nuclear Information System (INIS)

Nguyen, Ba Nghiep; Kunc, Vlastimil; Frame, Barbara J.; Phelps, Jay; Tucker III, Charles L.; Bapanapalli, Satish K.; Holbery, James D.; Smith, Mark T.

2007-01-01

This paper presents an experimental-modeling approach to predict the elastic properties of long-fiber injection-molded thermoplastics (LFTs). The approach accounts for fiber length and orientation distributions in LFTs. LFT samples were injection-molded for the study, and fiber length and orientation distributions were measured at different locations for use in the computation of the composite properties. The current fiber orientation model was assessed to determine its capability to predict fiber orientation in LFTs. Predicted fiber orientations for the studied LFT samples were also used in the calculation of the elastic properties of these samples, and the predicted overall moduli were then compared with the experimental results. The elastic property prediction was based on the Eshelby-Mori-Tanaka method combined with the orientation averaging technique. The predictions reasonably agree with the experimental LFT data

Bayesian Analysis of Demand Elasticity in the Italian Electricity Market

Directory of Open Access Journals (Sweden)

Maria Chiara D'Errico

2015-09-01

Full Text Available The liberalization of the Italian electricity market is a decade old. Within these last ten years, the supply side has been extensively analyzed, but not the demand side. The aim of this paper is to provide a new method for estimation of the demand elasticity, based on Bayesian methods applied to the Italian electricity market. We used individual demand bids data in the day-ahead market in the Italian Power Exchange (IPEX, for 2011, in order to construct an aggregate demand function at the hourly level. We took into account the existence of both elastic and inelastic bidders on the demand side. The empirical results show that elasticity varies significantly during the day and across periods of the year. In addition, the elasticity hourly distribution is clearly skewed and more so in the daily hours. The Bayesian method is a useful tool for policy-making, insofar as the regulator can start with a priori historical information on market behavior and estimate actual market outcomes in response to new policy actions.

Mechanical properties of concrete with SAP. Part II: Modulus of elasticity

DEFF Research Database (Denmark)

Hasholt, Marianne Tange; Jespersen, Morten H. Seneka; Jensen, Ole Mejlhede

2010-01-01

In this study, focus is on the modulus of elasticity for concrete with superabsorbent polymers (SAP). The results show that based on composite theory it is possible to establish a model, which predicts overall concrete elasticity. The model assumes a three phase material of aggregate, cement paste......, and air with volume fractions of the three phases as well as elastic properties of paste and aggregates as input parameters. Addition of SAP changes the E-modulus, because it both has an influence on properties of the cement paste and on the volume of air voids. Here, the E-modulus is an example...... a more or less empirical relation. The results show that when introducing SAP, models of a more empirical nature can be misleading (and e.g. relations stated in codes are often of this empirical nature). The reason is twofold: First, the empirical models often have a general problem with the effect...

TRU composition changes and their influence on FBR core characteristics in the LWR-to-FBR transition period

International Nuclear Information System (INIS)

Maruyama, Shuhei; Ohki, Shigeo; Mizuno, Tomoyasu

2009-01-01

In the conceptual core and fuel design studies in Fast Reactor Cycle Technology Development Project (FaCT Project) in Japan, much interest has been taken in the fuel nuclide compositions for a transition period from light water reactor to fast breeder reactor (FBR). In this paper, the range of transuranic (TRU) nuclide composition to be provided to FBR is evaluated with extended recycling scenario calculations. The influence of TRU composition changes on FBR core characteristics are also discussed with explanations of major contributing factors. (author)

Downstream pressure and elastic wall reflection of droplet flow in a T-junction microchannel

Science.gov (United States)

Pang, Yan; Liu, Zhaomiao; Zhao, Fuwang

2016-08-01

This paper discusses pressure variation on a wall during the process of liquid flow and droplet formation in a T-junction microchannel. Relevant pressure in the channel, deformation of the elastic wall, and responses of the droplet generation are analyzed using a numerical method. The pressure difference between the continuous and dispersed phases can indicate the droplet-generation period. The pressure along the channel of the droplet flow is affected by the position of droplets, droplet-generation period, and droplet escape from the outlet. The varying pressures along the channel cause a nonuniform deformation of the wall when they are elastic. The deformation is a vibration and has the same period as the droplet generation arising from the process of droplet formation.

An analysis of gasoline demand elasticities at the national and local levels in Mexico

International Nuclear Information System (INIS)

Crotte, Amado; Noland, Robert B.; Graham, Daniel J.

2010-01-01

The majority of evidence on gasoline demand elasticities is derived from models based on national data. Since the largest growth in population is now taking place in cities in the developing world it is important that we understand whether this national evidence is applicable to demand conditions at the local level. The aim of this paper is to estimate and compare gasoline per vehicle demand elasticities at the national and local levels in Mexico. National elasticities with respect to price, income, vehicle stock and metro fares are estimated using both a time series cointegration model and a panel GMM model for Mexican states. Estimates for Mexico City are derived by modifying national estimates according to mode shares as suggested by, and by estimating a panel Within Groups model with data aggregated by borough. Although all models agree on the sign of the elasticities the magnitudes differ greatly. Elasticities change over time and differ between the national and local levels, with smaller price responses in Mexico City. In general, price elasticities are smaller than those reported in the gasoline demand surveys, a pattern previously found in developing countries. The fact that income and vehicle stock elasticities increase over time may suggest that vehicles are being used more intensively in recent years and that Mexico City residents are purchasing larger vehicles. Elasticities with respect to metro fares are negligible, which suggests little substitution between modes. Finally, the fact that fuel efficiency elasticities are smaller than vehicle stock elasticities suggests that vehicle stock size, rather than its composition, has a larger impact on gasoline consumption in Mexico City. (author)

An analysis of gasoline demand elasticities at the national and local levels in Mexico

Energy Technology Data Exchange (ETDEWEB)

Crotte, Amado [Mexican Ministry of Communications and Transport, Mexico City (Mexico); Noland, Robert B. [Alan M. Voorhees Transportation Center, E. J. Bloustein School of Planning and Public Policy, Rutgers University, New Brunswick, NJ 08901 (United States); Graham, Daniel J. [Centre for Transport Studies, Department of Civil and Environmental Engineering, Imperial College London, SW7 2AZ London (United Kingdom)

2010-08-15

The majority of evidence on gasoline demand elasticities is derived from models based on national data. Since the largest growth in population is now taking place in cities in the developing world it is important that we understand whether this national evidence is applicable to demand conditions at the local level. The aim of this paper is to estimate and compare gasoline per vehicle demand elasticities at the national and local levels in Mexico. National elasticities with respect to price, income, vehicle stock and metro fares are estimated using both a time series cointegration model and a panel GMM model for Mexican states. Estimates for Mexico City are derived by modifying national estimates according to mode shares as suggested by, and by estimating a panel Within Groups model with data aggregated by borough. Although all models agree on the sign of the elasticities the magnitudes differ greatly. Elasticities change over time and differ between the national and local levels, with smaller price responses in Mexico City. In general, price elasticities are smaller than those reported in the gasoline demand surveys, a pattern previously found in developing countries. The fact that income and vehicle stock elasticities increase over time may suggest that vehicles are being used more intensively in recent years and that Mexico City residents are purchasing larger vehicles. Elasticities with respect to metro fares are negligible, which suggests little substitution between modes. Finally, the fact that fuel efficiency elasticities are smaller than vehicle stock elasticities suggests that vehicle stock size, rather than its composition, has a larger impact on gasoline consumption in Mexico City. (author)

Weight and body composition change over a six-week holiday period.

Science.gov (United States)

Wagner, D R; Larson, J N; Wengreen, H

2012-03-01

Change in weight and body composition was assessed over a six-week holiday period. Baseline testing occurred the Monday or Tuesday prior to Thanksgiving Day (November 24 or 25, 2008), and the post-holiday assessment was the Monday or Tuesday after New Year's Day (January 5 or 6, 2009). Thirteen men and 21 women ranging in age from 23-61 years completed the study. The majority of participants (24 of 34) perceived that they had gained weight, and four did gain ≥2 kg. However, despite some changes to dietary and exercise habits, on average there was no difference between pre-holiday weight (74.0±17.8 kg) and post-holiday weight (73.9±18.1 kg), nor between pre-holiday body fat percentage (25.4±9.0%) and post-holiday body fat percentage (25.4±8.9%). Despite a perception of substantial weight gain, body weight and body fat remained unchanged over a six-week holiday period.

Elastic properties of Gum Metal

International Nuclear Information System (INIS)

Kuramoto, Shigeru; Furuta, Tadahiko; Hwang, Junghwan; Nishino, Kazuaki; Saito, Takashi

2006-01-01

In situ X-ray diffraction measurements under tensile loading and dynamic mechanical analysis were performed to investigate the mechanisms of elastic deformation in Gum Metal. Tensile stress-strain curves for Gum Metal indicate that cold working substantially decreases the elastic modulus while increasing the yield strength, thereby confirming nonlinearity in the elastic range. The gradient of each curve decreased continuously to about one-third its original value near the elastic limit. As a result of this decrease in elastic modulus and nonlinearity, elastic deformability reaches 2.5% after cold working. Superelasticity is attributed to stress-induced martensitic transformations, although the large elastic deformation in Gum Metal is not accompanied by a phase transformation

Application of RMS for damage detection by guided elastic waves

Energy Technology Data Exchange (ETDEWEB)

Radzienski, M; Dolinski, L; Krawczuk, M [Gdansk University of Technology, Faculty of Electrical and Control Engineering, Narutowicza 11/12, 80-952 Gdansk (Poland); Zak, A; Ostachowicz, W, E-mail: Maciej.Radzienski@gmail.com [Szewalski Institute of Fluid-Flow Machinery, Polish Academy of Sciences, Fiszera 14, 80-952 Gdansk (Poland)

2011-07-19

This paper presents certain results of an experimental study related with a damage detection in structural elements based on deviations in guided elastic wave propagation patterns. In order to excite guided elastic waves within specimens tested piezoelectric transducers have been applied. As excitation signals 5 sine cycles modulated by Hanning window have been used. Propagation of guided elastic waves has been monitored by a scanning Doppler laser vibrometer. The time signals recorded during measurement have been utilised to calculate the values of RMS. It has turned out that the values of RMS differed significantly in damaged areas from the values calculated for the healthy ones. In this way it has become possible to pinpoint precisely the locations of damage over the entire measured surface. All experimental investigations have been carried out for thin aluminium or composite plates. Damage has been simulated by a small additional mass attached on the plate surface or by a narrow notch cut. It has been shown that proposed method allows one to localise damage of various shapes and sizes within structural elements over the whole area under investigation.

Application of RMS for damage detection by guided elastic waves

Science.gov (United States)

Radzieński, M.; Doliński, Ł.; Krawczuk, M.; dot Zak, A.; Ostachowicz, W.

2011-07-01

This paper presents certain results of an experimental study related with a damage detection in structural elements based on deviations in guided elastic wave propagation patterns. In order to excite guided elastic waves within specimens tested piezoelectric transducers have been applied. As excitation signals 5 sine cycles modulated by Hanning window have been used. Propagation of guided elastic waves has been monitored by a scanning Doppler laser vibrometer. The time signals recorded during measurement have been utilised to calculate the values of RMS. It has turned out that the values of RMS differed significantly in damaged areas from the values calculated for the healthy ones. In this way it has become possible to pinpoint precisely the locations of damage over the entire measured surface. All experimental investigations have been carried out for thin aluminium or composite plates. Damage has been simulated by a small additional mass attached on the plate surface or by a narrow notch cut. It has been shown that proposed method allows one to localise damage of various shapes and sizes within structural elements over the whole area under investigation.

Temperature-dependent elastic properties of Ti{sub 1−x}Al{sub x}N alloys

Energy Technology Data Exchange (ETDEWEB)

Shulumba, Nina [Department of Physics, Chemistry, and Biology (IFM), Linköping University, SE-581 83 Linköping (Sweden); Functional Materials, Saarland University, D-66123 Saarbrücken (Germany); Hellman, Olle [Division of Engineering and Applied Science, California Institute of Technology, Pasadena, California 91125 (United States); Department of Physics, Chemistry, and Biology (IFM), Linköping University, SE-581 83 Linköping (Sweden); Rogström, Lina; Raza, Zamaan; Tasnádi, Ferenc; Odén, Magnus [Department of Physics, Chemistry, and Biology (IFM), Linköping University, SE-581 83 Linköping (Sweden); Abrikosov, Igor A. [Department of Physics, Chemistry, and Biology (IFM), Linköping University, SE-581 83 Linköping (Sweden); Materials Modeling and Development Laboratory, NUST “MISIS,” 119049 Moscow (Russian Federation); LACOMAS Laboratory, Tomsk State University, 634050 Tomsk (Russian Federation)

2015-12-07

Ti{sub 1−x}Al{sub x}N is a technologically important alloy that undergoes a process of high temperature age-hardening that is strongly influenced by its elastic properties. We have performed first principles calculations of the elastic constants and anisotropy using the symmetry imposed force constant temperature dependent effective potential method, which include lattice vibrations and therefore the effects of temperature, including thermal expansion and intrinsic anharmonicity. These are compared with in situ high temperature x-ray diffraction measurements of the lattice parameter. We show that anharmonic effects are crucial to the recovery of finite temperature elasticity. The effects of thermal expansion and intrinsic anharmonicity on the elastic constants are of the same order, and cannot be considered separately. Furthermore, the effect of thermal expansion on elastic constants is such that the volume change induced by zero point motion has a significant effect. For TiAlN, the elastic constants soften non-uniformly with temperature: C{sub 11} decreases substantially when the temperature increases for all compositions, resulting in an increased anisotropy. These findings suggest that an increased Al content and annealing at higher temperatures will result in a harder alloy.

Density functional theory investigation of elastic properties and martensitic transformation of Ti-Ta alloys

Energy Technology Data Exchange (ETDEWEB)

Chakraborty, Tanmoy; Rogal, Jutta; Drautz, Ralf [Interdisciplinary Centre for Advanced Materials Simulation, Ruhr- Universitaet Bochum (Germany)

2016-07-01

Ti-Ta alloys are considered as promising materials for high temperature shape memory alloys as well as biomedical applications. The properties of these alloys have been shown to be strongly composition dependent. The temperature for the martensitic transformation between the high temperature cubic austenite and the low temperature orthorhombic martensite decreases linearly with increasing Ta content. Likewise, the elastic properties show clear trends with changing composition. We use density functional theory to investigate the involved phases in Ti-Ta where the disordered phases are treated by special quasi-random structures. To compare the stability of the involved phases as a function of temperature we calculate free energies using the quasi-harmonic Debye model. The obtained trends in the stability are consistent with experimentally measured transformation temperatures. Furthermore, we determine elastic properties which are in good agreement with experimentally observed trends.

The Nanomechanical and Tribological Properties of Restorative Dental Composites after Exposure in Different Types of Media

Directory of Open Access Journals (Sweden)

Hong-Yi Fan

2014-01-01

Full Text Available The aim of this study was to evaluate the effects of various acidic solutions on the surface mechanical properties of commercial resin composites with different microstructures (Filtek Z350 XT, TPH3, Durafill, and Superlux. Specimens were immersed in orange juice, cola, and distilled water for 5 days and the nanohardness, elastic modulus, and wear behavior of the samples were determined via the nanoindentation test and a reciprocating nanoscratch test. The nanoscratch morphology was observed using scanning electron microscopy (SEM and the wear depth was recorded by scanning probe microscopy (SPM. The results indicate that the nanofilled resin composites had the greatest hardest and highest elastic modulus, whereas the microfilled composites exhibited the lowest nanohardness and elastic modulus values. SEM observations showed that all resin composites underwent erosion and surface degradation after immersion in acidic solutions. Furthermore, the wear resistance was influenced by the composition of the acidic solution and was correlated with the nanohardness and elastic modulus. The dominant wear mechanism changed from plastic deformation to delamination after immersion in acidic solutions.

Mechanical properties of Composite Engineering Structures by Multivolume Micromechanical Modelling

Directory of Open Access Journals (Sweden)

B. Novotný

2000-01-01

Full Text Available Engineering structures often consist of elements having the character of a periodically repeated composite structure. A multivolume micromechanical model based on a representative cell division into r1 × r2 × r3 subcells with different elastic material properties has been used in this paper to derive macromechanical characteristics of the composite construction response to applied load and temperature changes. The multivolume method is based on ensuring the equilibrium of the considered volume on an average basis. In the same (average way, the continuity conditions of displacements and tractions at the interfaces between subcells and between neighboring representative elements are imposed, resulting in a homogenization procedure that eliminates the discrete nature of the composite model. The details of the method are shown for the case of a concrete block pavement. A parametric study is presented illustrating the influence of joint thickness, joint filling material properties and the quality of bonding between block and filler elements.

Periodic Contact and Crack Problems in Plane Elasticity

DEFF Research Database (Denmark)

Krenk, Steen

1976-01-01

By use of singular integral equations it is demonstrated how some periodic contact and crack problems can be solved in closed form. The integral equation in question is the same which is encountered when dealing with mixed boundary conditions on a circle. As analytical evaluation of the solution ...... may be quite complicated attention is drawn to a numerical quadrature method...

Aerosol chemical composition at Cabauw, the Netherlands as observed in two intensive periods in May 2008 and March 2009

NARCIS (Netherlands)

Mensah, A.A.; Holzinger, R.; Otjes, R.; Trimborn, A.; Mentel, T.F.; Brink, H. ten; Henzing, B.; Kiendler-Scharr, A.

2012-01-01

Observations of aerosol chemical composition in Cabauw, the Netherlands, are presented for two intensive measurement periods in May 2008 and March 2009. Sub-micron aerosol chemical composition was measured by an Aerodyne Aerosol Mass Spectrometer (AMS) and is compared to observations from aerosol

Structure, elastic properties and phase stability of Cr1-xAlxN

International Nuclear Information System (INIS)

Mayrhofer, P.H.; Music, D.; Reeswinkel, Th.; Fuss, H.-G.; Schneider, J.M.

2008-01-01

The effect of composition and metal sublattice population on the phase stability, structure and elastic properties of cubic (c), hexagonal (h) and orthorhombic spin-polarized Cr 1-x Al x N was studied using ab initio calculations. Excellent correlation between ab initio and experimentally obtained lattice parameters and elastic constants was obtained. The energy of formation suggests that the cubic phase can be stabilized for x in the range 0.48-0.75, depending on the metal sublattice population. The broad range of x, which is also observed in experiments, can be understood by considering the Al distribution induced changes in the configurational contribution to the total energy

Elastic properties and molar volume of rare-earth aluminosilicae glasses

International Nuclear Information System (INIS)

Tanabe, S.; Hirao, K.; Soga, N.

1992-01-01

This paper reports on the elastic properties, molar volume, and glass transition temperature (T g ) of rare-earth-containing aluminosilicate glasses that were investigated in the compositions of SiO 2 --LnAlO 3 and SiO 2 --Ln 3/4 Al 5/4 O 3 , where Ln is Y, La, Nd, Eu, or Yb. The molar volume decreased with decreased ionic size of the Ln 3+ ion, and T g and elastic moduli increased in the same order. The Yb-containing glasses showed the highest Young's modulus among all the oxide glasses, even higher than the highest value ever known fro glass containing Y 2 O 3 , as expected from the smaller ionic radius of Yb 3+ than that of Y 3+ . The bulk modulus was found to be almost proportional to the inverse four-thirds power of the molar volume of glasses in each composition, indicating that Ln 3+ ions can substitute for each other without changing the glass structure except for the size of the local structure around themselves. From the comparison of these properties, the structural role of rate-earth ions in these glasses is discussed

Material toughness, internal structure, and caldera-collapse frequencies in basaltic and composite edifices

Energy Technology Data Exchange (ETDEWEB)

Gudmundsson, Agust [Department of Earth Sciences, Queen' s Building, Royal Holloway University of London, Egham TW20 OEX (United Kingdom)], E-mail: a.gudmundsson@es.rhul.ac.uk

2008-10-01

Formation of, and slip on existing, collapse calderas is much more common in basaltic edifices than in composite edifices. I suggest that this difference is partly due to the composite edifices being tougher and more resistant to ring-fault formation than a basaltic edifices. The high matieral toughness of composite edifices is related to their being composed of rock layers with widely different elastic properties, the elastic mismatch promoting deflection and/or arrest of potential ring faults at layer contacts.

Form finding in elastic gridshells

Science.gov (United States)

Baek, Changyeob; Sageman-Furnas, Andrew O.; Jawed, Mohammad K.; Reis, Pedro M.

2018-01-01

Elastic gridshells comprise an initially planar network of elastic rods that are actuated into a shell-like structure by loading their extremities. The resulting actuated form derives from the elastic buckling of the rods subjected to inextensibility. We study elastic gridshells with a focus on the rational design of the final shapes. Our precision desktop experiments exhibit complex geometries, even from seemingly simple initial configurations and actuation processes. The numerical simulations capture this nonintuitive behavior with excellent quantitative agreement, allowing for an exploration of parameter space that reveals multistable states. We then turn to the theory of smooth Chebyshev nets to address the inverse design of hemispherical elastic gridshells. The results suggest that rod inextensibility, not elastic response, dictates the zeroth-order shape of an actuated elastic gridshell. As it turns out, this is the shape of a common household strainer. Therefore, the geometry of Chebyshev nets can be further used to understand elastic gridshells. In particular, we introduce a way to quantify the intrinsic shape of the empty, but enclosed regions, which we then use to rationalize the nonlocal deformation of elastic gridshells to point loading. This justifies the observed difficulty in form finding. Nevertheless, we close with an exploration of concatenating multiple elastic gridshell building blocks.

Printable elastic conductors by in situ formation of silver nanoparticles from silver flakes

Science.gov (United States)

Matsuhisa, Naoji; Inoue, Daishi; Zalar, Peter; Jin, Hanbit; Matsuba, Yorishige; Itoh, Akira; Yokota, Tomoyuki; Hashizume, Daisuke; Someya, Takao

2017-08-01

Printable elastic conductors promise large-area stretchable sensor/actuator networks for healthcare, wearables and robotics. Elastomers with metal nanoparticles are one of the best approaches to achieve high performance, but large-area utilization is limited by difficulties in their processability. Here we report a printable elastic conductor containing Ag nanoparticles that are formed in situ, solely by mixing micrometre-sized Ag flakes, fluorine rubbers, and surfactant. Our printable elastic composites exhibit conductivity higher than 4,000 S cm-1 (highest value: 6,168 S cm-1) at 0% strain, and 935 S cm-1 when stretched up to 400%. Ag nanoparticle formation is influenced by the surfactant, heating processes, and elastomer molecular weight, resulting in a drastic improvement of conductivity. Fully printed sensor networks for stretchable robots are demonstrated, sensing pressure and temperature accurately, even when stretched over 250%.

Elasticity theory of ultrathin nanofilms

International Nuclear Information System (INIS)

Li, Jiangang; Yun, Guohong; Narsu, B; Yao, Haiyan

2015-01-01

A self-consistent theoretical scheme for describing the elastic behavior of ultrathin nanofilms (UTNFs) was proposed. Taking into account the lower symmetry of an UTNF compared to its bulk counterpart, additional elastic and magnetoelastic parameters were introduced to model the elasticity rigorously. The applications of current theory to several elastic and magnetoelastic systems gave excellent agreement with experiments. More importantly, the surface elastic and magnetoelastic parameters used to fit the experimental results are physically reasonable and in close agreement with those obtained from experiment and simulation. This fact suggests that the additional elastic (magnetoelastic) constants due to symmetry breaking are of great importance in theoretical description of the mechanical properties of UTNFs. And we proved that the elasticity of UTNFs should be described by a three-dimensional model just including the intrinsic surface and bulk parameters, but not the effective surface parameters. It is believed that the theory reported here is a universal strategy for elasticity and magnetoelasticity of ultrathin films. (paper)

Size effect of the elastic modulus of rectangular nanobeams: Surface elasticity effect

International Nuclear Information System (INIS)

Yao Hai-Yan; Fan Wen-Liang; Yun Guo-Hong

2013-01-01

The size-dependent elastic property of rectangular nanobeams (nanowires or nanoplates) induced by the surface elasticity effect is investigated by using a developed modified core-shell model. The effect of surface elasticity on the elastic modulus of nanobeams can be characterized by two surface related parameters, i.e., inhomogeneous degree constant and surface layer thickness. The analytical results show that the elastic modulus of the rectangular nanobeam exhibits a distinct size effect when its characteristic size reduces below 100 nm. It is also found that the theoretical results calculated by a modified core-shell model have more obvious advantages than those by other models (core-shell model and core-surface model) by comparing them with relevant experimental measurements and computational results, especially when the dimensions of nanostructures reduce to a few tens of nanometers. (condensed matter: structural, mechanical, and thermal properties)

Lamb Wave Assessment of Fiber Volume Fraction in Composites

Science.gov (United States)

Seale, Michael D.; Smith, Barry T.; Prosser, W. H.; Zalameda, Joseph N.

1998-01-01

Among the various techniques available, ultrasonic Lamb waves offer a convenient method of examining composite materials. Since the Lamb wave velocity depends on the elastic properties of a material, an effective tool exists to evaluate composites by measuring the velocity of these waves. Lamb waves can propagate over long distances and are sensitive to the desired in-plane elastic properties of the material. This paper discusses a study in which Lamb waves were used to examine fiber volume fraction variations of approximately 0.40-0.70 in composites. The Lamb wave measurements were compared to fiber volume fractions obtained from acid digestion tests. Additionally, a model to predict the fiber volume fraction from Lamb wave velocity values was evaluated.

Elastic flexibility, fast-ion conduction, boson and floppy modes in AgPO3-AgI glasses

Science.gov (United States)

Novita, Deassy I.; Boolchand, P.; Malki, M.; Micoulaut, Matthieu

2009-05-01

Raman scattering, IR reflectance and modulated-DSC measurements are performed on specifically prepared dry (AgI)x(AgPO3)1-x glasses over a wide range of compositions 0%37.8% are elastically flexible. Raman optical elasticity power laws, trends in the nature of the glass transition endotherms, corroborate the three elastic phase assignments. Ionic conductivities reveal a step-like increase when glasses become stress-free at x>xc(1) = 9.5% and a logarithmic increase in conductivity (σ~(x-xc(2))μ) once they become flexible at x>xc(2) = 37.8% with a power law μ = 1.78. The power law is consistent with percolation of 3D filamentary conduction pathways. Traces of water doping lower Tg and narrow the reversibility window, and can also completely collapse it. Ideas on network flexibility promoting ion conduction are in harmony with the unified approach of Ingram et al (2008 J. Phys. Chem. B 112 859), who have emphasized the similarity of process compliance or elasticity relating to ion transport and structural relaxation in decoupled systems. Boson mode frequency and scattering strength display thresholds that coincide with the two elastic phase boundaries. In particular, the scattering strength of the boson mode increases almost linearly with glass composition x, with a slope that tracks the floppy mode fraction as a function of mean coordination number r predicted by mean-field rigidity theory. These data suggest that the excess low frequency vibrations contributing to the boson mode in flexible glasses come largely from floppy modes.

Identifying design parameters controlling damage behaviors of continuous fiber-reinforced thermoplastic composites using micromechanics as a virtual testing tool

KAUST Repository

Pulungan, Ditho Ardiansyah; Lubineau, Gilles; Yudhanto, Arief; Yaldiz, Recep; Schijve, Warden

2017-01-01

In this paper, we propose a micromechanical approach to predict damage mechanisms and their interactions in glass fibers/polypropylene thermoplastic composites. First, a representative volume element (RVE) of such materials was rigorously determined using a geometrical two-point probability function and the eigenvalue stabilization of homogenized elastic tensor obtained by Hill-Mandel kinematic homogenization. Next, the 3D finite element models of the RVE were developed accordingly. The fibers were modeled with an isotropic linear elastic material. The matrix was modeled with an isotropic linear elastic, rate-independent hyperbolic Drucker-Prager plasticity coupled with a ductile damage model that is able to show pressure dependency of the yield and damage behavior often found in a thermoplastic material. In addition, cohesive elements were inserted into the fiber-matrix interfaces to simulate debonding. The RVE faces are imposed with periodical boundary conditions to minimize the edge effect. The RVE was then subjected to transverse tensile loading in accordance with experimental tensile tests on [90]8 laminates. The model prediction was found to be in very good agreement with the experimental results in terms of the global stress-strain curves, including the linear and nonlinear portion of the response and also the failure point, making it a useful virtual testing tool for composite material design. Furthermore, the effect of tailoring the main parameters of thermoplastic composites is investigated to provide guidelines for future improvements of these materials.

Identifying design parameters controlling damage behaviors of continuous fiber-reinforced thermoplastic composites using micromechanics as a virtual testing tool

KAUST Repository

Pulungan, Ditho Ardiansyah

2017-03-31

In this paper, we propose a micromechanical approach to predict damage mechanisms and their interactions in glass fibers/polypropylene thermoplastic composites. First, a representative volume element (RVE) of such materials was rigorously determined using a geometrical two-point probability function and the eigenvalue stabilization of homogenized elastic tensor obtained by Hill-Mandel kinematic homogenization. Next, the 3D finite element models of the RVE were developed accordingly. The fibers were modeled with an isotropic linear elastic material. The matrix was modeled with an isotropic linear elastic, rate-independent hyperbolic Drucker-Prager plasticity coupled with a ductile damage model that is able to show pressure dependency of the yield and damage behavior often found in a thermoplastic material. In addition, cohesive elements were inserted into the fiber-matrix interfaces to simulate debonding. The RVE faces are imposed with periodical boundary conditions to minimize the edge effect. The RVE was then subjected to transverse tensile loading in accordance with experimental tensile tests on [90]8 laminates. The model prediction was found to be in very good agreement with the experimental results in terms of the global stress-strain curves, including the linear and nonlinear portion of the response and also the failure point, making it a useful virtual testing tool for composite material design. Furthermore, the effect of tailoring the main parameters of thermoplastic composites is investigated to provide guidelines for future improvements of these materials.

Non-linear waves in heterogeneous elastic rods via homogenization

KAUST Repository

Quezada de Luna, Manuel

2012-03-01

We consider the propagation of a planar loop on a heterogeneous elastic rod with a periodic microstructure consisting of two alternating homogeneous regions with different material properties. The analysis is carried out using a second-order homogenization theory based on a multiple scale asymptotic expansion. © 2011 Elsevier Ltd. All rights reserved.

Determination of the properties of composite interfaces by an ultrasonic method

Energy Technology Data Exchange (ETDEWEB)

Mal, A K; Karim, M R [Dept. of Mechanical, Aerospace and Nuclear Engineering, School of Engineering and Applied Science, Univ. of California, Los Angeles (USA); Bar-Cohen, Y [Douglas Aircraft Co., McDonnell Douglas Corp., Long Beach, CA (USA)

1990-06-15

The feasibility of using a recently developed ultrasonic technique to determine certain macroscopic properties of the interface zones of composite laminates is studied. The strong influence of the elastic properties and the thickness of the interface zone on the phase velocity of guided waves is demonstrated by means of a simple model of a single fiber embedded in a layer of the matrix material. The overall dynamic elastic moduli of a unidirectional graphite-epoxy composite laminate are determined through inversion of guided wave dispersion data obtained by the leaky Lamb wave experiment. The thickness and elastic properties of the interlaminar interface zone in a cross-ply graphite-epoxy laminate are also estimated by the same approach. (orig.).

On Elasticity Measurement in Cloud Computing

Directory of Open Access Journals (Sweden)

Wei Ai

2016-01-01

Full Text Available Elasticity is the foundation of cloud performance and can be considered as a great advantage and a key benefit of cloud computing. However, there is no clear, concise, and formal definition of elasticity measurement, and thus no effective approach to elasticity quantification has been developed so far. Existing work on elasticity lack of solid and technical way of defining elasticity measurement and definitions of elasticity metrics have not been accurate enough to capture the essence of elasticity measurement. In this paper, we present a new definition of elasticity measurement and propose a quantifying and measuring method using a continuous-time Markov chain (CTMC model, which is easy to use for precise calculation of elasticity value of a cloud computing platform. Our numerical results demonstrate the basic parameters affecting elasticity as measured by the proposed measurement approach. Furthermore, our simulation and experimental results validate that the proposed measurement approach is not only correct but also robust and is effective in computing and comparing the elasticity of cloud platforms. Our research in this paper makes significant contribution to quantitative measurement of elasticity in cloud computing.

Money flexibility, price elasticity, and elasticity of marginal utility of consumption

OpenAIRE

Malakhov, Sergey

2014-01-01

The development of G.Stigler’s original model of search describes the mathematical relationship between the elasticity of the marginal utility of consumption, the price elasticity, and the elasticity of the marginal utility of money income with respect to increase in the price of living and/or to inflation. This relationship can be used not only in economics of well-being but also in microeconomics where the increase in the price of living, i.e., in purchase price, can make consumption “bad” ...

Tensile Mechanical Property of Oil Palm Empty Fruit Bunch Fiber Reinforced Epoxy Composites

Science.gov (United States)

Ghazilan, A. L. Ahmad; Mokhtar, H.; Shaik Dawood, M. S. I.; Aminanda, Y.; Ali, J. S. Mohamed

2017-03-01

Natural, short, untreated and randomly oriented oil palm empty fruit bunch fiber reinforced epoxy composites were manufactured using vacuum bagging technique with 20% fiber volume composition. The performance of the composite was evaluated as an alternative to synthetic or conventional reinforced composites. Tensile properties such as tensile strength, modulus of elasticity and Poisson’s ratio were compared to the tensile properties of pure epoxy obtained via tensile tests as per ASTM D 638 specifications using Universal Testing Machine INSTRON 5582. The tensile properties of oil palm empty fruit bunch fiber reinforced epoxy composites were lower compared to plain epoxy structure with the decrement in performances of 38% for modulus of elasticity and 61% for tensile strength.

Motivation and compliance with intraoral elastics.

Science.gov (United States)

Veeroo, Helen J; Cunningham, Susan J; Newton, Jonathon Timothy; Travess, Helen C

2014-07-01

Intraoral elastics are commonly used in orthodontics and require regular changing to be effective. Unfortunately, poor compliance with elastics is often encountered, especially in adolescents. Intention for an action and its implementation can be improved using "if-then" plans that spell out when, where, and how a set goal, such as elastic wear, can be put into action. Our aim was to determine the effect of if-then plans on compliance with elastics. To identify common barriers to compliance with recommendations concerning elastic wear, semistructured interviews were carried out with 14 adolescent orthodontic patients wearing intraoral elastics full time. Emerging themes were used to develop if-then plans to improve compliance with elastic wear. A prospective pilot study assessed the effectiveness of if-then planning aimed at overcoming the identified barriers on compliance with elastic wear. Twelve participants were randomized equally into study and control groups; the study group received information about if-then planning. The participants were asked to collect used elastics, and counts of these were used to assess compliance. A wide range of motivational and volitional factors were described by the interviewed participants, including the perceived benefits of elastics, cues to remember, pain, eating, social situations, sports, loss of elastics, and breakages. Compliance with elastic wear was highly variable among patients. The study group returned more used elastics, suggesting increased compliance, but the difference was not significant. The use of if-then plans might improve compliance with elastic wear when compared with routine clinical instructions. Copyright © 2014 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Free vibrations and buckling analysis of carbon nanotube-reinforced composite Timoshenko beams on elastic foundation

International Nuclear Information System (INIS)

Yas, M.H.; Samadi, N.

2012-01-01

This study deals with free vibrations and buckling analysis of nanocomposite Timoshenko beams reinforced by single-walled carbon nanotubes (SWCNTs) resting on an elastic foundation. The SWCNTs are assumed to be aligned and straight with a uniform layout. Four different carbon nanotubes (CNTs) distributions including uniform and three types of functionally graded distributions of CNTs through the thickness are considered. The rule of mixture is used to describe the effective material properties of the nanocomposite beams. The governing equations are derived through using Hamilton's principle and then solved by using the generalized differential quadrature method (GDQM). Natural frequencies and critical buckling load are obtained for nanocomposite beams with different boundary conditions. Effects of several parameters, such as nanotube volume fraction, foundation stiffness parameters, slenderness ratios, CNTs distribution and boundary conditions on both natural frequency and critical buckling load are investigated. The results indicate that the above-mentioned parameters play a very important role on the free vibrations and buckling characteristics of the beam. Highlights: ► Beams with FG-X distribution have highest fundamental frequency. ► Beams with FG-X distribution have highest critical buckling load. ► Using elastic foundation, lead to increase the natural frequency. ► Using elastic foundation, lead to increase the critical buckling load. ► Increasing CNT volume fraction, lead to increase the natural frequency.

Long-Period Tidal Variations of the Earth's Rotation Rate

Science.gov (United States)

Desai, S.; Gross, R.; Wahr, J.

1999-01-01

Long-period tidal variations of the Earth's rotation rate are caused by the redistribution of mass associated with the respective elastic solid Earth tides, the ocean tide heights, and the anelasticity of the Earth's mantle, and by the relative angular momentum associated with the long-period ocean tide currents.

Generalization of Eshelby close-quote s Formula for a Single Ellipsoidal Elastic Inclusion to Poroelasticity and Thermoelasticity

International Nuclear Information System (INIS)

Berryman, J.G.

1997-01-01

Eshelby close-quote s formula gives the response of a single ellipsoidal elastic inclusion in an elastic whole space to a uniform strain imposed at infinity. Using a linear combination of results from two simple thought experiments, we show how this formula may be generalized to both poroelasticity and thermoelasticity. The resulting new formulas are important for applications to analysis of poroelastic and thermoelastic composites, including but not restricted to rocks. copyright 1997 The American Physical Society

Switching gains and health plan price elasticities: 20 years of managed competition reforms in The Netherlands.

Science.gov (United States)

Douven, Rudy; Katona, Katalin; T Schut, Frederik; Shestalova, Victoria

2017-11-01

In this paper we estimate health plan price elasticities and financial switching gains for consumers over a 20-year period in which managed competition was introduced in the Dutch health insurance market. The period is characterized by a major health insurance reform in 2006 to provide health insurers with more incentives and tools to compete, and to provide consumers with a more differentiated choice of products. Prior to the reform, in the period 1995-2005, we find a low number of switchers, between 2 and 4% a year, modest average total switching gains of 2 million euros per year and short-term health plan price elasticities ranging from -0.1 to -0.4. The major reform in 2006 resulted in an all-time high switching rate of 18%, total switching gains of 130 million euros, and a high short-term price elasticity of -5.7. During 2007-2015 switching rates returned to lower levels, between 4 and 8% per year, with total switching gains in the order of 40 million euros per year on average. Total switching gains could have been 10 times higher if all consumers had switched to one of the cheapest plans. We find short-term price elasticities ranging between -0.9 and -2.2. Our estimations suggest substantial consumer inertia throughout the entire period, as we find degrees of choice persistence ranging from about 0.8 to 0.9.

Testing and estimating time-varying elasticities of Swiss gasoline demand

International Nuclear Information System (INIS)

Neto, David

2012-01-01

This paper is intended to test and estimate time-varying elasticities for gasoline demand in Switzerland. For this purpose, a smooth time-varying cointegrating parameters model is investigated in order to describe smooth mutations of the Swiss gasoline demand. The methodology, based on Chebyshev polynomials, is rigorously outlined. Our empirical finding states that the time-invariance assumption does not hold for long-run price and income elasticities. Furthermore they highlight that gasoline demand passed through some periods of sensitivity and non sensitivity with respect to the price. Our empirical statements are of great importance to assess the performance of a gasoline tax as an instrument for CO 2 reduction policy. Indeed, such an instrument can contribute to reduce emissions of greenhouse gases only if the demand is not fully inelastic with respect to the price. Our results suggest that such a carbon-tax would not be always suitable since the price elasticity is found not stable over time and not always significant.

Characterization of the elastic displacement demand: Case study - Sofia city

International Nuclear Information System (INIS)

Paskaleva, I.; Kouteva, M.; Vaccari, F.; Panza, G.F.

2008-02-01

The results of the study on the seismic site response in a part of the metropolitan Sofia are discussed. The neo-deterministic seismic hazard assessment procedure has been used to compute realistic synthetic waveforms considering four earthquake scenarios, with magnitudes M = 3.7, M = 6.3 and M = 7.0. Source and site specific ground motion time histories are computed along three investigated cross sections, making use of the hybrid approach, combining the modal summation technique and the finite differences scheme. Displacement and acceleration response spectra are considered. These results are validated against the design elastic displacement response spectra and displacement demand, recommended in Eurocode 8. The elastic response design spectrum from the standard pseudo-acceleration, versus natural period, Tn, format is converted to the Sa - Sd format. The elastic displacement response spectra and displacement demand are discussed with respect to the earthquake magnitude, the seismic source-to-site distance, seismic source mechanism, and the local geological site conditions. (author)

Micromechanical models to guide the development of synthetic ‘brick and mortar’ composites

Science.gov (United States)

Begley, Matthew R.; Philips, Noah R.; Compton, Brett G.; Wilbrink, David V.; Ritchie, Robert O.; Utz, Marcel

2012-08-01

This paper describes a micromechanical analysis of the uniaxial response of composites comprising elastic platelets (bricks) bonded together with thin elastic perfectly plastic layers (mortar). The model yields closed-form results for the spatial variation of displacements in the bricks as a function of constituent properties, which can be used to calculate the effective properties of the composite, including elastic modulus, strength and work-to-failure. Regime maps are presented which indicate critical stresses for failure of the bricks and mortar as a function of constituent properties and brick architecture. The solution illustrates trade-offs between elastic modulus, strength and dissipated work that are a result of transitions between various failure mechanisms associated with brick rupture and rupture of the interfaces. Detailed scaling relationships are presented with the goal of providing material developers with a straightforward means to identify synthesis targets that balance competing mechanical behaviors and optimize material response. Ashby maps are presented to compare potential brick and mortar composites with existing materials, and identify future directions for material development.

Development of computer-aided design system of elastic sensitive elements of automatic metering devices

Science.gov (United States)

Kalinkina, M. E.; Kozlov, A. S.; Labkovskaia, R. I.; Pirozhnikova, O. I.; Tkalich, V. L.; Shmakov, N. A.

2018-05-01

The object of research is the element base of devices of control and automation systems, including in its composition annular elastic sensitive elements, methods of their modeling, calculation algorithms and software complexes for automation of their design processes. The article is devoted to the development of the computer-aided design system of elastic sensitive elements used in weight- and force-measuring automation devices. Based on the mathematical modeling of deformation processes in a solid, as well as the results of static and dynamic analysis, the calculation of elastic elements is given using the capabilities of modern software systems based on numerical simulation. In the course of the simulation, the model was a divided hexagonal grid of finite elements with a maximum size not exceeding 2.5 mm. The results of modal and dynamic analysis are presented in this article.

Martensitic textures: Multiscale consequences of elastic compatibility

International Nuclear Information System (INIS)

Shenoy, S.R.; Lookman, T.; Saxena, A.; Bishop, A.R.

2001-03-01

We show that a free energy entirely in the order-parameter strain variable(s), rather than the displacement field, provides a unified understanding of martensitic textures. We use compatibility equations, linking the strain tensor components in the bulk and at interfaces, that induce anisotropic order-parameter strain interactions. These two long-range bulk/interface potentials, together with local compositional fluctuations, drive the formation of global elastic textures. Relaxational simulations show the spontaneous formation (and evolution under stress/temperature quenches) of equal width parallel twins, branched twins, and tweed, including characteristic scaling of twin width with twin length. (author)

Acoustic examinations of elastic and inelastic properties of high-pressure polyethylene with different radiation prehistory

International Nuclear Information System (INIS)

Kardashev, B.K.; Nikanorov, S.P.; Kravchenko, V.S.; Malinov, V.I.; Punin, V.T.

2007-01-01

The influence of vibrational deformation amplitude on the dynamic elasticity modulus and internal friction of high-pressure polyethylene samples with different histories is studied. Acoustic measurements are made by a resonance method using the longitudinal vibrations of a composite piezoelectric vibrator at a frequency of ∼ 100 kHz. It is found that the microplasticity remains almost unaffected upon irradiation and aging, while the elasticity modulus and breaking elongation per unit length considerably depend on the history and are clearly correlated with each other. The observed effects are explained by the fact that atom-atom interaction and defects inside polymer macromolecules substantially influence the elastic modulus and breaking strength, while the inelastic microplastic strain is most likely associated with molecule-molecule interaction, which is insignificantly affected by irradiation [ru

Using the ultrasound and instrumented indentation techniques to measure the elastic modulus of engineering materials

International Nuclear Information System (INIS)

Meza, J. M.; Franco, E. E.; Farias, M. C. M.; Buiochi, F.; Souza, R. M.; Cruz, J.

2008-01-01

Currently, the acoustic and nano indentation techniques are two of the most used techniques for materials elastic modulus measurement. In this article fundamental principles and limitations of both techniques are shown and discussed. Last advances in nano indentation technique are also reviewed. an experimental study in ceramic, metallic, composite and single crystals was also done. Results shown that ultrasonic technique is capable to provide results in agreement with those reported in literature. However, ultrasonic technique does not allow measuring the elastic modulus of some small samples and single crystals. On the other hand, the nano indentation technique estimates the elastic modulus values in reasonable agreement with those measured by acoustic methods, particularly in amorphous materials, while in some policristaline materials some deviation from expected values was obtained. (Author) 29 refs

Determination of baryon-baryon elastic scattering phase shift from finite volume spectra in elongated boxes

Science.gov (United States)

Li, Ning; Wu, Ya-Jie; Liu, Zhan-Wei

2018-01-01

The relations between the baryon-baryon elastic scattering phase shifts and the two-particle energy spectrum in the elongated box are established. We studied the cases with both the periodic boundary condition and twisted boundary condition in the center of mass frame. The framework is also extended to the system of nonzero total momentum with periodic boundary condition in the moving frame. Moreover, we discussed the sensitivity functions σ (q ) that represent the sensitivity of higher scattering phases. Our analytical results will be helpful to extract the baryon-baryon elastic scattering phase shifts in the continuum from lattice QCD data by using elongated boxes.

On the use of elastic-plastic material characteristics for linear-elastic component assessments

International Nuclear Information System (INIS)

Kussmaul, K.; Silcher, H.; Eisele, U.

1995-01-01

In this paper the procedure of safety assessment of components by fracture mechanics analysis as recommended in TECDOC 717 is applied to two standard specimens of ductile cast iron. It is shown that the use of a pseudo-elastic K IJ -value in linear elastic safety analysis may lead to non-conservative results, when elastic-plastic material behaviour can be expected. (author)

Elastic wave localization in two-dimensional phononic crystals with one-dimensional random disorder and aperiodicity

International Nuclear Information System (INIS)

Yan Zhizhong; Zhang Chuanzeng; Wang Yuesheng

2011-01-01

The band structures of in-plane elastic waves propagating in two-dimensional phononic crystals with one-dimensional random disorder and aperiodicity are analyzed in this paper. The localization of wave propagation is discussed by introducing the concept of the localization factor, which is calculated by the plane-wave-based transfer-matrix method. By treating the random disorder and aperiodicity as the deviation from the periodicity in a special way, three kinds of aperiodic phononic crystals that have normally distributed random disorder, Thue-Morse and Rudin-Shapiro sequence in one direction and translational symmetry in the other direction are considered and the band structures are characterized using localization factors. Besides, as a special case, we analyze the band gap properties of a periodic planar layered composite containing a periodic array of square inclusions. The transmission coefficients based on eigen-mode matching theory are also calculated and the results show the same behaviors as the localization factor does. In the case of random disorders, the localization degree of the normally distributed random disorder is larger than that of the uniformly distributed random disorder although the eigenstates are both localized no matter what types of random disorders, whereas, for the case of Thue-Morse and Rudin-Shapiro structures, the band structures of Thue-Morse sequence exhibit similarities with the quasi-periodic (Fibonacci) sequence not present in the results of the Rudin-Shapiro sequence.

Evaluation of Interlaminar Stresses in Composite Laminates with a Bolt-Filled Hole Using a Linear Elastic Traction-Separation Description

Directory of Open Access Journals (Sweden)

Yong Cao

2017-01-01

Full Text Available Determination of the local interlaminar stress distribution in a laminate with a bolt-filled hole is helpful for optimal bolted joint design, due to the three-dimensional (3D nature of the stress field near the bolt hole. A new interlaminar stress distribution phenomenon induced by the bolt-head and clamp-up load, which occurs in a filled-hole composite laminate, is investigated. In order to efficiently evaluate interlaminar stresses under the complex boundary condition, a calculation strategy that using zero-thickness cohesive interface element is presented and validated. The interface element is based on a linear elastic traction-separation description. It is found that the interlaminar stress concentrations occur at the hole edge, as well as the interior of the laminate near the periphery of the bolt head. In addition, the interlaminar stresses near the periphery of the bolt head increased with an increase in the clamp-up load, and the interlaminar normal and shear stresses are not at the same circular position. Therefore, the clamp-up load cannot improve the interlaminar stress distribution in the laminate near the periphery of the bolt head, although it can reduce the magnitude of the interlaminar shear stress at the hole edge. Thus, the interlaminar stress distribution phenomena may lead to delamination initiation in the laminate near the periphery of the bolt head, and should be considered in composite bolted joint design.

Elastic and inelastic surface effects on ion penetration and the resulting sputtering and backscattering

International Nuclear Information System (INIS)

Hassanein, A.M.; Smith, D.L.

1985-01-01

The computer code ITMC (Ion Transport in Materials and Compounds) has been developed to study in detail the transport of charged particles in solid materials and surface related phenomena such as sputtered atoms and backscattered ions. The code is based on Monte Carlo methods to follow the path and the damage produced by the charged particles in three dimension as they slow down in target materials. Single-element targets as well as alloys with possible different surface and bulk compositions or with layered structures of different materials can be used. Various models developed to calculate the inelastic energy losses with target electrons can be used in the code. Most known interatomic potentials can also be used to calculate the elastic energy losses. The major advantages of the code are its ability and flexibility to use and compare various models of elastic and inelastic energy losses in any target with different compounds and different surface and bulk composition

On the dynamic buckling of a weakly damped nonlinear elastic ...

African Journals Online (AJOL)

In this paper we determine the dynamic buckling load of a strictly nonlinear but weakly damped elastic oscillatory model structure subjected to small perturbations The loading history is explicitly time dependent and varies slowly with time over a natural period of oscillation of the structure. A multiple timing regular ...

Safety enhancement of composites via periodic proof testing

OpenAIRE

Woodward, Joseph H.

1993-01-01

Approved for public release; distribution is unlimited. The development of new composite materials, which lack the historical field data base, has led to the need for an accelerated life testing method applicable to composites. Accelerated life testing by increasing the sustained stress levels requires the modeling and validation of a strength-life relation. Proof testing of composite fibers by over-loading is one step in the understanding of the relationship. It is also important in the r...

Elastic and piezoelectric fields around a quantum wire of zincblende heterostructures with interface elasticity effect

Science.gov (United States)

Ye, Wei; Liu, Yifei

2018-04-01

This work formulates the solutions to the elastic and piezoelectric fields around a quantum wire (QWR) with interface elasticity effect. Closed-form solutions to the piezoelectric potential field of zincblende QWR/matrix heterostructures grown along [111] crystallographic orientation are found and numerical results of InAs/InP heterostructures are provided as an example. The piezoelectric potential in the matrix depends on the interface elasticity, the radius and stiffness of the QWR. Our results indicate that interface elasticity can significantly alter the elastic and piezoelectric fields near the interface. Additionally, when the elastic property of the QWR is considered to be anisotropic in contrary to the common isotropic assumption, piezoelectric potentials are found to be distinct near the interface, but the deviations are negligible at positions far away from the interface.

Fracton-Elasticity Duality

Science.gov (United States)

Pretko, Michael; Radzihovsky, Leo

2018-05-01

Motivated by recent studies of fractons, we demonstrate that elasticity theory of a two-dimensional quantum crystal is dual to a fracton tensor gauge theory, providing a concrete manifestation of the fracton phenomenon in an ordinary solid. The topological defects of elasticity theory map onto charges of the tensor gauge theory, with disclinations and dislocations corresponding to fractons and dipoles, respectively. The transverse and longitudinal phonons of crystals map onto the two gapless gauge modes of the gauge theory. The restricted dynamics of fractons matches with constraints on the mobility of lattice defects. The duality leads to numerous predictions for phases and phase transitions of the fracton system, such as the existence of gauge theory counterparts to the (commensurate) crystal, supersolid, hexatic, and isotropic fluid phases of elasticity theory. Extensions of this duality to generalized elasticity theories provide a route to the discovery of new fracton models. As a further consequence, the duality implies that fracton phases are relevant to the study of interacting topological crystalline insulators.

Mathematical methods in elasticity imaging

CERN Document Server

Ammari, Habib; Garnier, Josselin; Kang, Hyeonbae; Lee, Hyundae; Wahab, Abdul

2015-01-01

This book is the first to comprehensively explore elasticity imaging and examines recent, important developments in asymptotic imaging, modeling, and analysis of deterministic and stochastic elastic wave propagation phenomena. It derives the best possible functional images for small inclusions and cracks within the context of stability and resolution, and introduces a topological derivative-based imaging framework for detecting elastic inclusions in the time-harmonic regime. For imaging extended elastic inclusions, accurate optimal control methodologies are designed and the effects of uncertainties of the geometric or physical parameters on stability and resolution properties are evaluated. In particular, the book shows how localized damage to a mechanical structure affects its dynamic characteristics, and how measured eigenparameters are linked to elastic inclusion or crack location, orientation, and size. Demonstrating a novel method for identifying, locating, and estimating inclusions and cracks in elastic...

Micromechanical models to guide the development of synthetic 'brick and mortar' composites

NARCIS (Netherlands)

Begley, M.R.; Philips, N.R.; Compton, B.G.; Wilbrink, D.V.; Ritchie, R.O.; Utz, M.

2012-01-01

This paper describes a micromechanical analysis of the uniaxial response of composites comprising elastic platelets (bricks) bonded together with thin elastic perfectly plastic layers (mortar). The model yields closed-form results for the spatial variation of displacements in the bricks as a

Ultrashort-period lateral composition modulation in TlInGaAsN/TlInP structures

International Nuclear Information System (INIS)

Ishimaru, Manabu; Tanaka, Yuusuke; Hasegawa, Shigehiko; Asahi, Hajime; Sato, Kazuhisa; Konno, Toyohiko J.

2009-01-01

We prepared TlInGaAsN/TlInP quantum well structures using gas source molecular-beam epitaxy and characterized them by means of transmission electron microscopy and scanning transmission electron microscopy. It was found that naturally formed vertical quantum wells, so-called lateral composition modulation (LCM), with a periodicity of ∼1 nm are formed in TlInGaAsN layers. We discuss their formation process using a simple kinetic Ising model for layer-by-layer growth, and point out that the formation of ultrashort-period LCM is a universal phenomenon in most of epitaxially grown III-V semiconductor alloys.

Activity and selectivity control through periodic composition forcing over Fischer-Tropsch catalysts

Energy Technology Data Exchange (ETDEWEB)

Silveston, P L; Hudgins, R R; Adesina, A A; Ross, G S; Feimer, J L

1986-01-01

Data collected under steady-state and periodic composition forcing of the Fischer-Tropsch synthesis over three commonly used catalysts demonstrate that both activity and selectivity can be changed by the latter operating mode. Synthesis of hydrocarbons up to C/sub 7/are favored at the expense of the higher carbon numbers for the Co catalyst, while for the Ru catalyst, only the C/sub 3/ and lower species are favored. Only methane production is stimulated with the Fe catalyst. Fe and Ru catalysts shift production from alkenes to alkanes. Transient data is interpreted in the paper.

Elasticity theory and applications

CERN Document Server

Saada, Adel S; Hartnett, James P; Hughes, William F

2013-01-01

Elasticity: Theory and Applications reviews the theory and applications of elasticity. The book is divided into three parts. The first part is concerned with the kinematics of continuous media; the second part focuses on the analysis of stress; and the third part considers the theory of elasticity and its applications to engineering problems. This book consists of 18 chapters; the first of which deals with the kinematics of continuous media. The basic definitions and the operations of matrix algebra are presented in the next chapter, followed by a discussion on the linear transformation of points. The study of finite and linear strains gradually introduces the reader to the tensor concept. Orthogonal curvilinear coordinates are examined in detail, along with the similarities between stress and strain. The chapters that follow cover torsion; the three-dimensional theory of linear elasticity and the requirements for the solution of elasticity problems; the method of potentials; and topics related to cylinders, ...

Morphology and Chemical Composition of soot particles emitted by Wood-burning Cook-Stoves: a HRTEM, XPS and Elastic backscattering Studies.

Science.gov (United States)

Carabali-Sandoval, G. A., Sr.; Castro, T.; Peralta, O.; De la Cruz, W.; Días, J.; Amelines, O.; Rivera-Hernández, M.; Varela, A.; Muñoz-Muñoz, F.; Policroniades, R.; Murillo, G.; Moreno, E.

2014-12-01

The morphology, microstructure and the chemical composition on surface of soot particles were studied by using high resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS) and elastic backscattering spectrometry. In order to obtain freshly soot particles emitted by home-made wood-burning cook stoves, copper grids for Transmission Electron Microscope (TEM) were placed on the last two of an 8-stages MOUDI cascade impactor. The analysis of HRTEM micrographs revealed the nanostructure and the particle size of soot particles. The XPS survey spectra show a large carbon peak around 285 eV and the oxygen signal at 533 eV. Some differences observed in the carbon/oxygen (C/O) ratio of the particles probably depend on the combustion process efficiency of each cook-stove analyzed. The C-1s XPS spectra show an asymmetric broad peak and other with low intensity that corresponds to sp2 and sp3hybridization, which were fitted with a convolution using Gaussian functions. Elastic backscattering technique allows a chemical elemental analysis of samples and confirms the presence of C, O and Si observed by XPS. Additionally, the morphological properties of soot aggregates were analyzed calculating the border-based fractal dimension (Df). Particles exhibit complex shapes with high values of Df. Also, real-time absorption (σabs) and scattering (σsct) coefficients of fine (with aerodynamic diameter < 2.5 µm) soot particles were measured. The trend in σabs and σsct indicate that the cooking process has two important combustion stages which varied in its flaming strength, being vigorous in the first stage and soft in the second one.

Elastic properties of Sr- and Mg-doped lanthanum gallate at elevated temperature

Science.gov (United States)

Okamura, T.; Shimizu, S.; Mogi, M.; Tanimura, M.; Furuya, K.; Munakata, F.

The elastic moduli, i.e., Young's modulus, shear modulus and Poisson's ratio, of a sintered La 0.9Sr 0.1Ga 0.8Mg 0.2O 3- δ bulk have been experimentally determined in the temperature range from room temperature to 1373 K using a resonance technique. Anomalous elastic properties were observed over a wide temperature range from 473 to 1173 K. In the results for internal friction and in X-ray diffraction measurements at elevated temperature, two varieties of structural changes were seen in La 0.9Sr 0.1Ga 0.8Mg 0.2O 3- δ in the examined temperature range. The results agreed with the findings of a previous crystallographic study of the same composition system by Slater et al. In addition, the temperature range in which a successive structural change occurred in La 0.9Sr 0.1Ga 0.8Mg 0.2O 3- δ was the same as that exhibiting the anomalous elastic properties. Taking all the results together, it can be inferred that the successive structural change in the significant temperature range is responsible for the elastic property anomaly of La 0.9Sr 0.1Ga 0.8Mg 0.2O 3- δ.

[Study on elasticity of medical service demand at the township level in China].

Science.gov (United States)

Shi, Hong-xing; Lv, Jun; Xie, Yi-ping; Wang, Ying; Jia, Jin-zhong; Chang, Feng-shui; Duan, Lin; Sun, Mei; Wang, Zhi-feng; Hao, Mo

2010-06-18

To find out the economic laws regulating medical service demand in accordance with influencing factors at the township level, thus to provide references for further adjusting the medical service demand reasonably in the future. The model of medical service demand was established to measure the elasticity of demand in 49 township health clinics in 1995, 1999, 2003 and 2007. The price elasticity of outpatient and inpatient demand was stable during the four periods, and the average value was -0.029 and -0.132 respectively; the average value of income elasticity was 0.973 and 0.977, registering a downward trend in general. The medical service demand at the township level is price inelastic, indicating that it is a necessity for rural residents. The downward trend of income elasticity under the influence of some health policies illustrates a lightening in economic burden for medical service demand among rural residents in township health clinics.

Micromechanics of Composite Materials

CERN Document Server

Dvorak, George

2013-01-01

This book presents a broad exposition of analytical and numerical methods for modeling composite materials, laminates, polycrystals and other heterogeneous solids, with emphasis on connections between material properties and responses on several length scales, ranging from the nano and microscales to the macroscale. Many new results and methods developed by the author are incorporated into a rich fabric of the subject, which has been explored by several researchers over the last 40 years.   The first  part of the book reviews anisotropic elasticity theory, and then it describes the frequently used procedures and theorems for bounding and estimating overall properties, local fields and energy changes in elastic inhomogeneities, heterogeneous media, fiber composites and functionally graded materials.  Those are caused by mechanical loads and by phase eigenstrains, such as thermal, transformation and inelastic strains, and also by cavities and cracks.    Worked examples show that the eigendeformations may...

Forecasting of resonances vibration equipment with elastic waves coolant and with the external periodic loads on NPP with WWER

International Nuclear Information System (INIS)

Proskuryakov, K.N.; Zaporozhets, M.V.; Fedorov, A.I.

2015-01-01

Forecasting are carried out for external loads in relation to the main circulation circuit - dynamic loads caused by the rotation of the MCP, dynamic loads caused by the earthquake, dynamic loads caused by damage to the MCP in the earthquake. A comparison of the response spectrum of one of the variants of the base of the NPP, with the frequency vibration of the primary circuit equipment for NPP with WWER-1000 and self-frequency of elastic waves in the fluid. Analysis of the comparison results shows that the frequency of vibration of the main equipment of the reactor plant and elastic waves are in the frequency band in the spectrum response corresponding to the maximum amplitude of the seismic action [ru

The impact of dark chocolate intake on arterial elasticity in individuals with HIV/AIDS undergoing ART: a randomized, double-blind, crossover trial.

Science.gov (United States)

Teixeira, Andrea Mariana Nunes da Costa; Luzia, Liania Alves; de Souza, Suelen Jorge; de Almeida Petrilli, Aline; Pontilho, Patrícia de Moraes; de Souza, Jose Maria Pacheco; Segurado, Aluísio Augusto Cotrim; Efraim, Priscila; Picone, Camila de Melo; Rondo, Patrícia Helen de Carvalho

2017-06-21

An increase in the frequency of cardiovascular diseases has been observed in the HIV/AIDS population. Studies involving healthy subjects or subjects with other diseases have shown benefits of chocolate supplementation on endothelial function and vasodilation. We evaluate the impact of chocolate consumption on arterial elasticity in people living with human immunodeficiency virus - PLHIV. A double-blind, crossover trial including 110 PLHIV (19 to 59 years) on antiretroviral therapy - ART for at least 6 months and with a viral load of chocolate or placebo with a 15-d washout period. Each participant received one of the two sequences: A (dark chocolate, placebo chocolate); B (placebo chocolate, dark chocolate). Arterial elasticity was measured using the HDI/PulseWave™ CR-2000 CardioVascular Profiling System®. Body composition, lipid profile, C-reactive protein, and thiobarbituric acid reactive substances were also assessed. Analysis of variance (ANOVA) for repeated measures using the Stata 11.0® program was used for cross-over analysis. Most subjects were men (59.0%) and Caucasian (46.1%) and the mean age was 44.6 ± 7.1 years. The mean time since diagnosis of HIV infection was 13.7 ± 5.3 years and the mean duration of ART was 12.9 ± 4.2 years. Chocolate consumption resulted in significant alterations in the large artery elasticity index - LAEI (p = 0.049) and the mean concentration of HDL-c was higher after supplementation with dark chocolate (p = 0.045). This is the first study to evaluate the effect of chocolate on arterial elasticity in PLHIV. The results showed that dark chocolate consumption for 15 days improved the elastic properties of the LAEI in PLHIV. These findings, added to the noninvasive method used, may expand the knowledge of CVDs in this population.

Vibration of an Elastic Circular Plate on an Elastic Half Space

DEFF Research Database (Denmark)

Krenk, Steen; Schmidt, H.

1981-01-01

The axisymmetric problem of a vibrating elastic plate on an elastic half space is solved by a direct method, in which the contact stresses and the normal displacements of the plate are taken as the unknown functions. First, the influence functions that give the displacements in terms...

Coupling multiscale X-ray physics and micromechanics for bone tissue composition and elasticity determination from micro-CT data, by example of femora from OVX and sham rats

Science.gov (United States)

Hasslinger, Patricia; Vass, Viktoria; Dejaco, Alexander; Blanchard, Romane; Örlygsson, Gissur; Gargiulo, Paolo; Hellmich, Christian

2016-05-01

Due to its high resolution, micro-CT (Computed Tomograph) scanning is the key to assess bone quality of sham and OVX (ovariectomized) rats. Combination of basic X-ray physics, such as the energy- and chemistry-dependence of attenuation coefficients, with results from ashing tests on rat bones, delivers mineral, organic, and water volume fractions within the voxels. Additional use of a microelastic model for bone provides voxel-specific elastic properties. The new method delivers realistic bone mass densities, and reveals that OVX protocols may indeed induce some bone mass loss, while the average composition of the bone tissue remains largely unaltered.

Designing interactively with elastic splines

DEFF Research Database (Denmark)

Brander, David; Bærentzen, Jakob Andreas; Fisker, Ann-Sofie

2018-01-01

We present an algorithm for designing interactively with C1 elastic splines. The idea is to design the elastic spline using a C1 cubic polynomial spline where each polynomial segment is so close to satisfying the Euler-Lagrange equation for elastic curves that the visual difference becomes neglig...... negligible. Using a database of cubic Bézier curves we are able to interactively modify the cubic spline such that it remains visually close to an elastic spline....

The wave attenuation mechanism of the periodic local resonant metamaterial

Science.gov (United States)

Chang, I.-Ling; Liang, Zhen-Xian; Kao, Hao-Wei; Chang, Shih-Hsiang; Yang, Chih-Ying

2018-01-01

This research discusses the wave propagation behavior and attenuation mechanism of the elastic metamaterial with locally resonant sub-structure. The dispersion relation of the single resonance system, i.e., periodic spring mass system with sub-structure, could be derived based on lattice dynamics and the band gap could be easily identified. The dynamically equivalent properties, i.e., mass and elastic property, of the single resonance system are derived and found to be frequency dependent. Negative effective properties are found in the vicinity of the local resonance. It is examined whether the band gap always coincides with the frequency range of negative effective properties. The wave attenuation mechanism and the characteristic dynamic behavior of the elastic metamaterial are also studied from the energy point of view. From the analysis, it is clarified that the coupled Bragg-resonance band gap is much wider than the narrow-banded local resonance and the corresponding effective material properties at band gap could be either positive or negative. However, the band gap is totally overlapping with the frequency range of negative effective properties for the metamaterial with band gap purely caused by local resonance. The presented analysis can be extended to other forms of elastic metamaterials involving periodic resonator structures.

Correlation between ultrasonic nonlinearity and elastic nonlinearity in heat-treated aluminum alloy

Energy Technology Data Exchange (ETDEWEB)

Kim, Jong Beom; Jhang, Kyung Young [Hanyang University, Seoul (Korea, Republic of)

2017-04-15

The nonlinear ultrasonic technique is a potential nondestructive method to evaluate material degradation, in which the ultrasonic nonlinearity parameter is usually measured. The ultrasonic nonlinearity parameter is defined by the elastic nonlinearity coefficients of the nonlinear Hooke’s equation. Therefore, even though the ultrasonic nonlinearity parameter is not equal to the elastic nonlinearity parameter, they have a close relationship. However, there has been no experimental verification of the relationship between the ultrasonic and elastic nonlinearity parameters. In this study, the relationship is experimentally verified for a heat-treated aluminum alloy. Specimens of the aluminum alloy were heat-treated at 300°C for different periods of time (0, 1, 2, 5, 10, 20, and 50 h). The relative ultrasonic nonlinearity parameter of each specimen was then measured, and the elastic nonlinearity parameter was determined by fitting the stress-strain curve obtained from a tensile test to the 5th-order-polynomial nonlinear Hooke’s equation. The results showed that the variations in these parameters were in good agreement with each other.

Frequency-dependant homogenized properties of composite using spectral analysis method

International Nuclear Information System (INIS)

Ben Amor, M; Ben Ghozlen, M H; Lanceleur, P

2010-01-01

An inverse procedure is proposed to determine the material constants of multilayered composites using a spectral analysis homogenization method. Recursive process gives interfacial displacement perpendicular to layers in term of deepness. A fast-Fourier transform (FFT) procedure has been used in order to extract the wave numbers propagating in the multilayer. The upper frequency bound of this homogenization domain is estimated. Inside the homogenization domain, we discover a maximum of three planes waves susceptible to propagate in the medium. A consistent algorithm is adopted to develop an inverse procedure for the determination of the materials constants of multidirectional composite. The extracted wave numbers are used as the inputs for the procedure. The outputs are the elastic constants of multidirectional composite. Using this method, the frequency dependent effective elastic constants are obtained and example for [0/90] composites is given.

The Morishima Gross elasticity of substitution

OpenAIRE

Blackorby, Charles; Primont, Daniel; Russell, R. Robert

2007-01-01

We show that the Hotelling-Lau elasticity of substitution, an extension of the Allen-Uzawa elasticity to allow for optimal output-quantity (or utility) responses to changes in factor prices, inherits all of the failings of the Allen-Uzawa elasticity identified by Blackorby and Russell [1989 AER]. An analogous extension of the Morishima elasticity of substitution to allow for output quantity changes preserves the salient properties of the original Hicksian notion of elasticity of substitution.

Discrepancy between exercise performance, body composition, and sex steroid response after a six-week detraining period in professional soccer players.

Science.gov (United States)

Koundourakis, Nikolaos E; Androulakis, Nikolaos E; Malliaraki, Niki; Tsatsanis, Christos; Venihaki, Maria; Margioris, Andrew N

2014-01-01

The aim of this study was to examine the effects of a six-week off-season detraining period on exercise performance, body composition, and on circulating sex steroid levels in soccer players. Fifty-five professional male soccer players, members of two Greek Superleague Teams (Team A, n = 23; Team B, n = 22), participated in the study. The first two weeks of the detraining period the players abstained from any physical activity. The following four weeks, players performed low-intensity (50%-60% of VO2max) aerobic running of 20 to 30 minutes duration three times per week. Exercise performance testing, anthropometry, and blood sampling were performed before and after the six-week experimental period. Our data showed that in both teams A and B the six-week detraining period resulted in significant reductions in maximal oxygen consumption (60,31±2,52 vs 57,67±2,54; pperiod resulted in a rapid loss of exercise performance adaptations and optimal body composition status, but did not affect sex steroid resting levels. The insignificant changes in sex steroid concentration indicate that these hormones were a non-contributing parameter for the observed negative effects of detraining on exercise performance and body composition.

Elastic least-squares reverse time migration

KAUST Repository

Feng, Zongcai

2017-03-08

We use elastic least-squares reverse time migration (LSRTM) to invert for the reflectivity images of P- and S-wave impedances. Elastic LSRTMsolves the linearized elastic-wave equations for forward modeling and the adjoint equations for backpropagating the residual wavefield at each iteration. Numerical tests on synthetic data and field data reveal the advantages of elastic LSRTM over elastic reverse time migration (RTM) and acoustic LSRTM. For our examples, the elastic LSRTM images have better resolution and amplitude balancing, fewer artifacts, and less crosstalk compared with the elastic RTM images. The images are also better focused and have better reflector continuity for steeply dipping events compared to the acoustic LSRTM images. Similar to conventional leastsquares migration, elastic LSRTM also requires an accurate estimation of the P- and S-wave migration velocity models. However, the problem remains that, when there are moderate errors in the velocity model and strong multiples, LSRTMwill produce migration noise stronger than that seen in the RTM images.

Elastic least-squares reverse time migration

KAUST Repository

Feng, Zongcai; Schuster, Gerard T.

2017-01-01

We use elastic least-squares reverse time migration (LSRTM) to invert for the reflectivity images of P- and S-wave impedances. Elastic LSRTMsolves the linearized elastic-wave equations for forward modeling and the adjoint equations for backpropagating the residual wavefield at each iteration. Numerical tests on synthetic data and field data reveal the advantages of elastic LSRTM over elastic reverse time migration (RTM) and acoustic LSRTM. For our examples, the elastic LSRTM images have better resolution and amplitude balancing, fewer artifacts, and less crosstalk compared with the elastic RTM images. The images are also better focused and have better reflector continuity for steeply dipping events compared to the acoustic LSRTM images. Similar to conventional leastsquares migration, elastic LSRTM also requires an accurate estimation of the P- and S-wave migration velocity models. However, the problem remains that, when there are moderate errors in the velocity model and strong multiples, LSRTMwill produce migration noise stronger than that seen in the RTM images.

Fringe instability in constrained soft elastic layers.

Science.gov (United States)

Lin, Shaoting; Cohen, Tal; Zhang, Teng; Yuk, Hyunwoo; Abeyaratne, Rohan; Zhao, Xuanhe

2016-11-04

Soft elastic layers with top and bottom surfaces adhered to rigid bodies are abundant in biological organisms and engineering applications. As the rigid bodies are pulled apart, the stressed layer can exhibit various modes of mechanical instabilities. In cases where the layer's thickness is much smaller than its length and width, the dominant modes that have been studied are the cavitation, interfacial and fingering instabilities. Here we report a new mode of instability which emerges if the thickness of the constrained elastic layer is comparable to or smaller than its width. In this case, the middle portion along the layer's thickness elongates nearly uniformly while the constrained fringe portions of the layer deform nonuniformly. When the applied stretch reaches a critical value, the exposed free surfaces of the fringe portions begin to undulate periodically without debonding from the rigid bodies, giving the fringe instability. We use experiments, theory and numerical simulations to quantitatively explain the fringe instability and derive scaling laws for its critical stress, critical strain and wavelength. We show that in a force controlled setting the elastic fingering instability is associated with a snap-through buckling that does not exist for the fringe instability. The discovery of the fringe instability will not only advance the understanding of mechanical instabilities in soft materials but also have implications for biological and engineered adhesives and joints.

Determining the optimum topology of composites by the flexural stiffness criterion

Directory of Open Access Journals (Sweden)

Vasile MOGA

2012-06-01

Full Text Available An important stage in designing of pieces made of composite materials consists of establishing the composite topology in such a way that it has certain properties needed in exploitation. The paper presents the mathematical apparatus and the calculation programme for establishing the optimum thickness of the composite groups so that it should have certain imposed (given flexural stiffness. The method is applicable to all types of laminate composites, no matter of the cladding or matrix nature. The direct problem consists in determining the thickness of the groups and composite, minimising the bar mass, for an imposed (given flexural stiffness, knowing the densities and elasticity modules of the groups. The indirect problem consists in determining the maximum stiffness, the thickness of the groups and composite for a given (imposed mass, knowing the densities and elasticity modules of the groups. The presented programmes offer to the producer of this kind of materials the possibility to quickly establish the optimum topology.

LaCu6-xAgx : A promising host of an elastic quantum critical point

Science.gov (United States)

Poudel, L.; Cruz, C. de la; Koehler, M. R.; McGuire, M. A.; Keppens, V.; Mandrus, D.; Christianson, A. D.

2018-05-01

Structural properties of LaCu6-xAgx have been investigated using neutron and x-ray diffraction, and resonant ultrasound spectroscopy (RUS) measurements. Diffraction measurements indicate a continuous structural transition from orthorhombic (Pnma) to monoclinic (P21 / c) structure. RUS measurements show softening of natural frequencies at the structural transition, consistent with the elastic nature of the structural ground state. The structural transition temperatures in LaCu6-xAgx decrease with Ag composition until the monoclinic phase is completely suppressed at xc = 0.225 . All of the evidence is consistent with the presence of an elastic quantum critical point in LaCu6-xAgx .

Industrial and residential electricity demand dynamics in Japan: How did price and income elasticities evolve from 1989 to 2014?

International Nuclear Information System (INIS)

Wang, Nan; Mogi, Gento

2017-01-01

This study estimates the price and income elasticities of industrial and residential electricity demand in Japan with the annual data from 1989 to 2014. A time varying parameter (TVP) model with the Kalman filter is applied to monitor the evolution of consumer behaviors in the “post-bubble” period given the exogenous shock (financial crisis in 2008) and the structural breaks (electricity deregulation and Fukushima Daiichi crisis). The TVP model can provide a robust estimation of elasticities and can detect the outliers and the structural breaks. The results suggest that both industrial and residential consumers become less sensitive to price after the electricity deregulation and the financial crisis, and more sensitive to price after the Fukushima Daiichi crisis. Especially the industrial sector is less sensitive to price after the retail deregulation. By contrast, the income elasticities of industrial and residential sector consumers are stable during the examined period. Results also indicate that a negative relationship exists between the price elasticity of electricity demand and the price level of electricity after the electric sector deregulation. Some insights on the further electric sector reform and the environmental taxation in Japan are also provided. - Highlights: • A time varying parameter model is calculated with the Kalman filter. • Income elasticities are stable while price elasticities are time-varying. • Industrial sector is less sensitive to price change than residential sector. • Negative relationship between price elasticity and price level is found.

Heterogeneous dissipative composite structures

Science.gov (United States)

Ryabov, Victor; Yartsev, Boris; Parshina, Ludmila

2018-05-01

The paper suggests mathematical models of decaying vibrations in layered anisotropic plates and orthotropic rods based on Hamilton variation principle, first-order shear deformation laminated plate theory (FSDT), as well as on the viscous-elastic correspondence principle of the linear viscoelasticity theory. In the description of the physical relationships between the materials of the layers forming stiff polymeric composites, the effect of vibration frequency and ambient temperature is assumed as negligible, whereas for the viscous-elastic polymer layer, temperature-frequency relationship of elastic dissipation and stiffness properties is considered by means of the experimentally determined generalized curves. Mitigation of Hamilton functional makes it possible to describe decaying vibration of anisotropic structures by an algebraic problem of complex eigenvalues. The system of algebraic equation is generated through Ritz method using Legendre polynomials as coordinate functions. First, real solutions are found. To find complex natural frequencies of the system, the obtained real natural frequencies are taken as input values, and then, by means of the 3rd order iteration method, complex natural frequencies are calculated. The paper provides convergence estimates for the numerical procedures. Reliability of the obtained results is confirmed by a good correlation between analytical and experimental values of natural frequencies and loss factors in the lower vibration tones for the two series of unsupported orthotropic rods formed by stiff GRP and CRP layers and a viscoelastic polymer layer. Analysis of the numerical test data has shown the dissipation & stiffness properties of heterogeneous composite plates and rods to considerably depend on relative thickness of the viscoelastic polymer layer, orientation of stiff composite layers, vibration frequency and ambient temperature.

Homogenization of Winkler-Steklov spectral conditions in three-dimensional linear elasticity

Science.gov (United States)

Gómez, D.; Nazarov, S. A.; Pérez, M. E.

2018-04-01

We consider a homogenization Winkler-Steklov spectral problem that consists of the elasticity equations for a three-dimensional homogeneous anisotropic elastic body which has a plane part of the surface subject to alternating boundary conditions on small regions periodically placed along the plane. These conditions are of the Dirichlet type and of the Winkler-Steklov type, the latter containing the spectral parameter. The rest of the boundary of the body is fixed, and the period and size of the regions, where the spectral parameter arises, are of order ɛ . For fixed ɛ , the problem has a discrete spectrum, and we address the asymptotic behavior of the eigenvalues {β _k^ɛ }_{k=1}^{∞} as ɛ → 0. We show that β _k^ɛ =O(ɛ ^{-1}) for each fixed k, and we observe a common limit point for all the rescaled eigenvalues ɛ β _k^ɛ while we make it evident that, although the periodicity of the structure only affects the boundary conditions, a band-gap structure of the spectrum is inherited asymptotically. Also, we provide the asymptotic behavior for certain "groups" of eigenmodes.

Mapped Chebyshev Pseudo-Spectral Method for Dynamic Aero-Elastic Problem of Limit Cycle Oscillation

Science.gov (United States)

Im, Dong Kyun; Kim, Hyun Soon; Choi, Seongim

2018-05-01

A mapped Chebyshev pseudo-spectral method is developed as one of the Fourier-spectral approaches and solves nonlinear PDE systems for unsteady flows and dynamic aero-elastic problem in a given time interval, where the flows or elastic motions can be periodic, nonperiodic, or periodic with an unknown frequency. The method uses the Chebyshev polynomials of the first kind for the basis function and redistributes the standard Chebyshev-Gauss-Lobatto collocation points more evenly by a conformal mapping function for improved numerical stability. Contributions of the method are several. It can be an order of magnitude more efficient than the conventional finite difference-based, time-accurate computation, depending on the complexity of solutions and the number of collocation points. The method reformulates the dynamic aero-elastic problem in spectral form for coupled analysis of aerodynamics and structures, which can be effective for design optimization of unsteady and dynamic problems. A limit cycle oscillation (LCO) is chosen for the validation and a new method to determine the LCO frequency is introduced based on the minimization of a second derivative of the aero-elastic formulation. Two examples of the limit cycle oscillation are tested: nonlinear, one degree-of-freedom mass-spring-damper system and two degrees-of-freedom oscillating airfoil under pitch and plunge motions. Results show good agreements with those of the conventional time-accurate simulations and wind tunnel experiments.

Non-linear elastic deformations

CERN Document Server

Ogden, R W

1997-01-01

Classic in the field covers application of theory of finite elasticity to solution of boundary-value problems, analysis of mechanical properties of solid materials capable of large elastic deformations. Problems. References.

ElasticSearch cookbook

CERN Document Server

Paro, Alberto

2015-01-01

If you are a developer who implements ElasticSearch in your web applications and want to sharpen your understanding of the core elements and applications, this is the book for you. It is assumed that you've got working knowledge of JSON and, if you want to extend ElasticSearch, of Java and related technologies.

Multipurpose hooks for elastic attachment

Directory of Open Access Journals (Sweden)

Siddharth Shashidhar Revankar

2014-01-01

Full Text Available As certain bracket systems do not include hooks on premolar brackets for elastic attachment, Kobayashi or custom made ligature hooks have proven as an alternative. However, these hooks tend to bend labially when used with heavy elastics and these elastics can even pop loose from the hooks on mouth opening. The following article describes an innovative multipurpose hook which is simple, stiff and inexpensive and can be used for engagement of class II elastics on premolars in case of missing molars as well as engagement of intermaxillary elastics for settling of occlusion in finishing stages. As the hooks can be prefabricated, this saves a lot of chair side time and is more practical for use in day-to-day orthodontic practice.

Influence of different beverages on the force degradation of intermaxillary elastics: an in vitro study.

Science.gov (United States)

Leão Filho, Jorge César Borges; Gallo, Daphine Beatriz; Santana, Regis Meller; Guariza-Filho, Odilon; Camargo, Elisa Souza; Tanaka, Orlando Motohiro

2013-01-01

The aim of this study was to evaluate in vitro the effects of frequently ingested beverages on force degradation of intermaxillary elastics. One hundred and eighty 1/4-inch intermaxillary elastics (TP Orthodontics) were immersed into six different beverages: (1) Coca-Cola®; (2) Beer; (3) Orange juice; (4) Red wine; (5) Coffee and (6) artificial saliva (control). The period of immersion was 15 min for the first and second cycles and 30 min for the third to fifth cycles. Tensile forces were read in a tensile testing machine before and after the five immersion cycles. One-way repeated measures ANOVA was used to identify significant differences. Force degradation was seen in all evaluated groups and at all observation periods (pdegradation was present at the initial periods, decreasing gradually over time. However, no statistically significant differences were seen among groups at the same periods, showing that different groups behaved similarly. The chemical nature of the evaluated beverages was not able to influence the degree of force degradation at all observation periods.

Spectral dimension of elastic Sierpinski gaskets with general elastic forces

International Nuclear Information System (INIS)

Liu, S.H.; Liu, A.J.

1985-01-01

The spectral dimension is calculated for a Sierpinski gasket with the most general elastic restoring forces allowed by symmetry. The elastic forces consist of bond-stretching and angle-bending components. The spectral dimension is the same as that for the bond-stretching-force (central-force) model. This demonstrates that on the Sierpinski gasket the two types of forces belong to the same universality class

The fluid control mechanism of bionic structural heterogeneous composite materials and its potential application in enhancing pump efficiency

Directory of Open Access Journals (Sweden)

Limei Tian

2015-11-01

Full Text Available Studies have shown that the structure of dolphin skin controls fluid media dynamically. Gaining inspiration from this phenomenon, a kind of bionic structural heterogeneous composite material was designed. The bionic structural heterogeneous composite material is composed of two materials: a rigid metal base layer with bionic structures and an elastic polymer surface layer with the corresponding mirror structures. The fluid control mechanism of the bionic structural heterogeneous composite material was investigated using a fluid–solid interaction method in ANSYS Workbench. The results indicated that the bionic structural heterogeneous composite material’s fluid control mechanism is its elastic deformation, which is caused by the coupling action between the elastic surface material and the bionic structure. This deformation can decrease the velocity gradient of the fluid boundary layer through changing the fluid–solid actual contact surface and reduce the frictional force. The bionic structural heterogeneous composite material can also absorb some energy through elastic deformation and avoid energy loss. The bionic structural heterogeneous composite material was applied to the impeller of a centrifugal pump in a contrast experiment, increasing the pump efficiency by 5% without changing the hydraulic model of the impeller. The development of this bionic structural heterogeneous composite material will be straightforward from an engineering point of view, and it will have valuable practical applications.

EFFECTIVE ELASTIC PROPERTIES OF ALUMINA-ZIRCONIA COMPOSITE CERAMICS - PART 4. TENSILE MODULUS OF POROUS ALUMINA AND ZIRCONIA

Directory of Open Access Journals (Sweden)

W. Pabst

2004-12-01

Full Text Available In this fourth paper of a series on the effective elastic properties of alumina-zirconia composite ceramics the influence of porosity on the effective tensile modulus of alumina and zirconia ceramics is discussed. The examples investigated are alumina and zirconia ceramics prepared from submicron powders by starch consolidation casting using two different types of starch, potato starch (median size D50 =47.2 µm and corn starch (median size D50 =13.7 µm. The dependence of effective tensile moduli E, on the porosity f, measured for porosities in the ranges of approx. 19-55 vol.% and 10-42 vol.% for alumina and zirconia, respectively, using a resonant frequency technique, was evaluated by fitting with various model relations, including newly developed ones. A detailed comparison of the fitting results suggests the superiority of the new relation E/E0 = (1 - f·(1 - f/fC, developed by the authors (with the tensile modulus of the dense ceramic material E0 and the critical porosity fC, over most other existing fit models. Only for special purposes and well-behaved data sets the recently proposed exponential relation E/E0 = exp [-Bf/(1 - f] and the well-known Phani-Niyogi relation E/E0 = (1 - f/fCN might be preferable.

A 3D Orthotropic Elastic Continuum Damage Material Model

Energy Technology Data Exchange (ETDEWEB)

English, Shawn Allen [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Brown, Arthur A. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

2013-08-01

A three dimensional orthotropic elastic constitutive model with continuum damage is implemented for polymer matrix composite lamina. Damage evolves based on a quadratic homogeneous function of thermodynamic forces in the orthotropic planes. A small strain formulation is used to assess damage. In order to account for large deformations, a Kirchhoff material formulation is implemented and coded for numerical simulation in Sandia’s Sierra Finite Element code suite. The theoretical formulation is described in detail. An example of material parameter determination is given and an example is presented.

Nonlinear analysis of AS4/PEEK thermoplastic composite laminate using a one parameter plasticity model

Science.gov (United States)

Sun, C. T.; Yoon, K. J.

1990-01-01

A one-parameter plasticity model was shown to adequately describe the orthotropic plastic deformation of AS4/PEEK (APC-2) unidirectional thermoplastic composite. This model was verified further for unidirectional and laminated composite panels with and without a hole. The nonlinear stress-strain relations were measured and compared with those predicted by the finite element analysis using the one-parameter elastic-plastic constitutive model. The results show that the one-parameter orthotropic plasticity model is suitable for the analysis of elastic-plastic deformation of AS4/PEEK composite laminates.

Elastic properties of LaSnxNi5-x compounds

International Nuclear Information System (INIS)

Yeheskel, O.; Nattrass, C.E.; Leisure, R.G.; Jacob, I.; Bowman, R.C. Jr.

2004-01-01

Ultrasonic methods were used to measure the room-temperature elastic moduli of polycrystalline LaSn x Ni 5-x compounds for 0≤x≤0.5. These materials are of great importance for their hydrogen storage properties. The samples, prepared by a hot isostatic pressing method, had near-theoretical densities with calculated porosities ranging from 0 to 1.5%. The porosity-corrected moduli decreased with increasing x. Poisson's ratio was approximately constant at 0.314 for all the compounds. The Debye temperature, calculated from the RT polycrystalline moduli, decreased from 359 to 344 K as x increased from 0 to 0.5. The results were used to calculate the elastic interaction energy of an interstitial hydrogen atom with the strain fields of all the other interstitial hydrogen. This energy was in turn used to calculate the critical temperature below which phase separation occurs in LaM x Ni 5-x H y compounds (M=Sn or Al). It was found that the critical temperature decreases with increasing x, confirming in a more general way a conclusion drawn for a specific case from earlier thermodynamic measurements. It is suggested that the lowering of the critical temperature plays a role in limiting the width of the plateaus in pressure-composition isotherms for the two-phase regions of these compounds. This suggestion implies a relation between the elastic properties and the maximum hydrogen capacity

Optimization of the piezoelectric response of 0–3 composites: a modeling approach

International Nuclear Information System (INIS)

Chambion, B; Goujon, L; Badie, L; Mugnier, Y; Barthod, C; Galez, C; Wiebel, S; Venet, C

2011-01-01

Finite element modeling is used in this study to optimize the electromechanical behavior of 0–3 composites according to the material properties of their constituents. Our modeling approach considers an 'extended' 2D representative volume element (RVE) with randomly dispersed piezoelectric particles. A variable distribution of their polarization axes is also implemented because a full periodic arrangement of fillers and a unique poling orientation are unrealistic in practice. Comparisons with a simpler RVE and with an analytical model based on the Mori–Tanaka approach are performed as a function of the particle concentration for the elastic, dielectric and piezoelectric homogenized properties. An optimization of the piezoelectric response of 0–3 composites according to material considerations is then computed, allowing it to be shown that the piezoelectric strain coefficient is not the only relevant parameter and that lead-free piezoelectric fillers such as LiNbO 3 and ZnO are competitive alternatives. Finally, the piezoelectric responses of 0–3 composites with different filler arrangements are quantitatively compared to 1–3 composites and to the corresponding bulk material

Numerical study of two disks settling in an Oldroyd-B fluid: From periodic interaction to chaining

Science.gov (United States)

Pan, Tsorng-Whay; Glowinski, Roland

2017-12-01

In this article, we present a numerical study of the dynamics of two disks sedimenting in a narrow vertical channel filled with an Oldroyd-B fluid. Two kinds of particle dynamics are observed: (i) a periodic interaction between the two disks, and (ii) the formation of a two-disk chain. For the periodic interaction of the two disks, two different motions are observed: (a) the two disks stay far apart and interact periodically, and (b) the two disks interact closely and then far apart in a periodic way, like the drafting, kissing, and tumbling of two disks sedimenting in a Newtonian fluid, due to a weak elastic force. Concerning the formation of a two-disk chain occurring at higher values of the elasticity number, either a tilted chain or a vertical chain is observed. Our simulations show that, as expected, the values of the elasticity and Mach numbers are the determining factors concerning the particle chain formation and its orientation.

Cell Elasticity Determines Macrophage Function

Science.gov (United States)

Patel, Naimish R.; Bole, Medhavi; Chen, Cheng; Hardin, Charles C.; Kho, Alvin T.; Mih, Justin; Deng, Linhong; Butler, James; Tschumperlin, Daniel; Fredberg, Jeffrey J.; Krishnan, Ramaswamy; Koziel, Henry

2012-01-01

Macrophages serve to maintain organ homeostasis in response to challenges from injury, inflammation, malignancy, particulate exposure, or infection. Until now, receptor ligation has been understood as being the central mechanism that regulates macrophage function. Using macrophages of different origins and species, we report that macrophage elasticity is a major determinant of innate macrophage function. Macrophage elasticity is modulated not only by classical biologic activators such as LPS and IFN-γ, but to an equal extent by substrate rigidity and substrate stretch. Macrophage elasticity is dependent upon actin polymerization and small rhoGTPase activation, but functional effects of elasticity are not predicted by examination of gene expression profiles alone. Taken together, these data demonstrate an unanticipated role for cell elasticity as a common pathway by which mechanical and biologic factors determine macrophage function. PMID:23028423

Cell elasticity determines macrophage function.

Directory of Open Access Journals (Sweden)

Naimish R Patel

Full Text Available Macrophages serve to maintain organ homeostasis in response to challenges from injury, inflammation, malignancy, particulate exposure, or infection. Until now, receptor ligation has been understood as being the central mechanism that regulates macrophage function. Using macrophages of different origins and species, we report that macrophage elasticity is a major determinant of innate macrophage function. Macrophage elasticity is modulated not only by classical biologic activators such as LPS and IFN-γ, but to an equal extent by substrate rigidity and substrate stretch. Macrophage elasticity is dependent upon actin polymerization and small rhoGTPase activation, but functional effects of elasticity are not predicted by examination of gene expression profiles alone. Taken together, these data demonstrate an unanticipated role for cell elasticity as a common pathway by which mechanical and biologic factors determine macrophage function.

CONCERNING THE ELASTIC ORTHOTROPIC MODEL APPLIED TO WOOD ELASTIC PROPERTIES

OpenAIRE

Tadeu Mascia,Nilson

2003-01-01

Among the construction materials, wood reveals an orthotropic pattern, because of unique characteristics in its internal structure with three axes of wood biological directions (longitudinal, tangential and radial). elastic symmetry: longitudinal, tangential and radial, reveals an orthotropic pattern. The effect of grain angle orientation onin the elastic modulus constitutes the fundamental cause forof wood anisotropy. It is responsible for the greatest changes in the values of the constituti...

Analysis of Mode II Crack in Bilayered Composite Beam

Science.gov (United States)

Rizov, Victor I.; Mladensky, Angel S.

2012-06-01

Mode II crack problem in cantilever bilayered composite beams is considered. Two configurations are analyzed. In the first configuration the crack arms have equal heights while in the second one the arms have different heights. The modulus of elasticity and the shear modulus of the beam un-cracked part in the former case and the moment of inertia in the latter are derived as functions of the two layers characteristics. The expressions for the strain energy release rate, G are obtained on the basis of the simple beam theory according to the hypotheses of linear elastic fracture mechanics. The validity of these expressions is established by comparison with a known solution. Parametrical investigations for the influence of the moduli of elasticity ratio as well as the moments of inertia ratio on the strain energy release rate are also performed. The present article is a part of comprehensive investigation in Fracture mechanics of composite beams.

Transient waves in visco-elastic media

CERN Document Server

Ricker, Norman

1977-01-01

Developments in Solid Earth Geophysics 10: Transient Waves in Visco-Elastic Media deals with the propagation of transient elastic disturbances in visco-elastic media. More specifically, it explores the visco-elastic behavior of a medium, whether gaseous, liquid, or solid, for very-small-amplitude disturbances. This volume provides a historical overview of the theory of the propagation of elastic waves in solid bodies, along with seismic prospecting and the nature of seismograms. It also discusses the seismic experiments, the behavior of waves propagated in accordance with the Stokes wave

Linear models of income patterns in consumer demand for foods and evaluation of its elasticity

Directory of Open Access Journals (Sweden)

Pavel Syrovátka

2005-01-01

Full Text Available The paper is focused on the use of the linear constructions for developing of Engel’s demand models in the field of the food-consumer demand. In the theoretical part of the paper, the linear approximations of this demand models are analysed on the bases of the linear interpolation. In the same part of this text, the hyperbolic elasticity function was defined for the linear Engel model. The behaviour of the hyperbolic elasticity function and its properties were consequently investigated too. The behaviour of the determined elasticity function was investigated according to the values of the intercept point and the direction parameter in the original linear Engel model. The obtained theoretical findings were tested using the real data of Czech Statistical Office. The developed linear Engel model was explicitly dynamised, because the achieved database was formed into the time series. With respect to the two variables definitions of the hyperbolic function in the theoretical part of the text, the determined dynamic model of the Engel demand for food was transformed into the form with parametric intercept point:ret* = At + 0.0946 · rmt*,where the values of absolute member are defined as:At = 1773.0973 + 9.3064 · t – 0.3023 · t2; (t = 1, 2, ... 32.The value of At in the parametric linear model of Engel consumer demand for food was during the observed period (1995–2002 always positive. Thus, the hyperbolic elasticity function achieved the elasticity coefficients from the interval:ηt ∈〈+0; +1.Within quantitative analysis of Engel demand for food in the Czech Republic during the given time period, it was founded, that income elasticity of food expenditures of the average Czech household was moved between +0.4080 and +0.4511. The Czech-household demand for food is thus income inelastic with the normal income reactions.

Linear elastic properties derivation from microstructures representative of transport parameters.

Science.gov (United States)

Hoang, Minh Tan; Bonnet, Guy; Tuan Luu, Hoang; Perrot, Camille

2014-06-01

It is shown that three-dimensional periodic unit cells (3D PUC) representative of transport parameters involved in the description of long wavelength acoustic wave propagation and dissipation through real foam samples may also be used as a standpoint to estimate their macroscopic linear elastic properties. Application of the model yields quantitative agreement between numerical homogenization results, available literature data, and experiments. Key contributions of this work include recognizing the importance of membranes and properties of the base material for the physics of elasticity. The results of this paper demonstrate that a 3D PUC may be used to understand and predict not only the sound absorbing properties of porous materials but also their transmission loss, which is critical for sound insulation problems.

Theme-period, as the basic compositional form during the first movement of Isak Shehu`s Symphony “Illyrians”

Directory of Open Access Journals (Sweden)

Fatos Lumani

2017-03-01

Full Text Available The traditional doctrine of musical forms has its sentence, phrase, period and punctuation. Questions, exclamations, subordinate clauses are everywhere, voices rise and fall, and, in all of this, the gesture of music is borrowed from the speaking voice” (Adorno, Gillespie, 1993. Based on the quote of Adorno (1993, we will analyze this paper with the purpose of answering a few questions concerning the already designated thesis “The theme – Period, a fundamental compositional form in the first movement of the symphony by Cesk Zadeja”, talking through the period from different perspectives as follows: The complex sentence and the period in music; The initial forms of the period in music; The period in classicism/the period and the folk melodies in the classical symphonies; Theme-period, as the basic compositional form during the first movement of Isak Shehu`s Symphony. As an introduction we would like to refer to some studies/lectures that relate to language with music, such as: “The Unanswered Question: Six Talks at Harvard”(Bernstein, 1981 where Bernstein in his opening fi rst lecture clarified the significance of “the interdisciplinary strategy by saying that “...the best way to ‘know’ a thing is in the context of another discipline”. Within these six lectures, Bernstein explains his ideas regarding the universality of music drawing analogies to other disciplines such as linguistics, philosophy, aesthetics, acoustics and history of music. As the primary interdisciplinary subject, Bernstein chose the recent work of Noam Chomsky on linguistic theories about “Language and Mind”. In the first three lectures, Bernstein analyzes the music from a linguistic aspect: phonology (sound, syntax (structure and semantics (meaning, pinpointing the music of the classical period.

Surface excess elasticity of gold: Ab initio coefficients and impact on the effective elastic response of nanowires

International Nuclear Information System (INIS)

Elsner, B.A.M.; Müller, S.; Bargmann, S.; Weissmüller, J.

2017-01-01

Predicting the influence of the surface on the effective elastic properties of nanoscale structures and nanomaterials remains a challenge, which we here address on both levels, continuum and atomic. Density Functional Theory (DFT) computation at the atomic level yields the first reliable surface excess elastic parameters for the (111) and (001) surfaces of gold. At the continuum level, we derive closed-form expressions for the effective elastic behavior that can be combined with the DFT-derived excess elastic parameters to obtain the effective axial, torsion, and bending stiffness of circular nanowires with surface excess elasticity. The two approaches use different reference frames, and we emphasize the need for consistent stress definitions and for conversion between the separate stress measures when transferring results between the approaches. We present excess elastic parameters separately for Cauchy and 2 nd Piola-Kirchhoff stresses, demonstrating that the conversion substantially modifies their numerical value and may even invert their sign. The results afford an assessment of the contribution of the surface excess elastic parameters to the effective elastic response of nanoscale beams or wires. This assessment sheds doubt on earlier suggestions relating experimental observations of an effective stiffening or softening at small size to the excess elasticity of clean surfaces.

Surface elastic properties in silicon nanoparticles

Science.gov (United States)

Melis, Claudio; Giordano, Stefano; Colombo, Luciano

2017-09-01

The elastic behavior of the external surface of a solid body plays a key role in nanomechanical phenomena. While bulk elasticity enjoys the benefits of a robust theoretical understanding, many surface elasticity features remain unexplored: some of them are here addressed by blending together continuum elasticity and atomistic simulations. A suitable readdressing of the surface elasticity theory allows to write the balance equations in arbitrary curvilinear coordinates and to investigate the dependence of the surface elastic parameters on the mean and Gaussian curvatures of the surface. In particular, we predict the radial strain induced by surface effects in spherical and cylindrical silicon nanoparticles and provide evidence that the surface parameters are nearly independent of curvatures and, therefore, of the surface conformation.

Effect of AlF3 on the Density and Elastic Properties of Zinc Tellurite Glass Systems

Science.gov (United States)

Sidek, Haji Abdul Aziz; Rosmawati, Shaharuddin; Halimah, Mohamed Kamari; Matori, Khamirul Amin; Talib, Zainal Abidin

2012-01-01

This paper presents the results of the physical and elastic properties of the ternary zinc oxyfluoro tellurite glass system. Systematic series of glasses (AlF3)x(ZnO)y(TeO2)z with x = 0–19, y = 0–20 and z = 80, 85, 90 mol% were synthesized by the conventional rapid melt quenching technique. The composition dependence of the physical, mainly density and molar volume, and elastic properties is discussed in term of the AlF3 modifiers addition that are expected to produce quite substantial changes in their physical properties. The absence of any crystalline peaks in the X-ray diffraction (XRD) patterns of the present glass samples indicates the amorphous nature. The addition of AlF3 lowered the values of the densities in ternary oxyfluorotellurite glass systems. The longitudinal and transverse ultrasonic waves propagated in each glass sample were measured using a MBS8020 ultrasonic data acquisition system. All the velocity data were taken at 5 MHz frequency and room temperature. The longitudinal modulus (L), shear modulus (G), Young’s modulus (E), bulk modulus (K) and Poisson’s ratio (σ) are obtained from both velocities data and their respective density. Experimental data shows the density and elastic moduli of each AlF3-ZnO-TeO2 series are found strongly depend upon the glass composition. The addition of AlF3 modifiers into the zinc tellurite causes substantial changes in their density, molar volume as well as their elastic properties.

Approximation by planar elastic curves

DEFF Research Database (Denmark)

Brander, David; Gravesen, Jens; Nørbjerg, Toke Bjerge

2016-01-01

We give an algorithm for approximating a given plane curve segment by a planar elastic curve. The method depends on an analytic representation of the space of elastic curve segments, together with a geometric method for obtaining a good initial guess for the approximating curve. A gradient......-driven optimization is then used to find the approximating elastic curve....

Price and income elasticities of crude oil import demand in South Africa: A cointegration analysis

International Nuclear Information System (INIS)

Ziramba, Emmanuel

2010-01-01

This paper examines the demand for imported crude oil in South Africa as a function of real income and the price of crude oil over the period 1980-2006. We carried out the Johansen co integration multivariate analysis to determine the long-run income and price elasticities. A unique long-run cointegration relationship exists between crude oil imports and the explanatory variables. The short-run dynamics are estimated by specifying a general error correction model. The estimated long-run price and income elasticities of -0.147 and 0.429 suggest that import demand for crude oil is price and income inelastic. There is also evidence of unidirectional long-run causality running from real GDP to crude oil imports. - Research Highlights: →The paper examines the demand for imported crude oil in South Africa over the period 1980-2006. → The estimated long-run price and income elasticities are -0.147 and 0.429, respectively. → There is evidence of unidirectional long-run causality running from real GDP to crude oil imports.

Price and income elasticities of crude oil import demand in South Africa: A cointegration analysis

Energy Technology Data Exchange (ETDEWEB)

Ziramba, Emmanuel, E-mail: zirame@unisa.ac.z [Department of Economics, University of South Africa, P.O Box 392, Unisa 0003 (South Africa)

2010-12-15

This paper examines the demand for imported crude oil in South Africa as a function of real income and the price of crude oil over the period 1980-2006. We carried out the Johansen co integration multivariate analysis to determine the long-run income and price elasticities. A unique long-run cointegration relationship exists between crude oil imports and the explanatory variables. The short-run dynamics are estimated by specifying a general error correction model. The estimated long-run price and income elasticities of -0.147 and 0.429 suggest that import demand for crude oil is price and income inelastic. There is also evidence of unidirectional long-run causality running from real GDP to crude oil imports. - Research Highlights: {yields}The paper examines the demand for imported crude oil in South Africa over the period 1980-2006. {yields} The estimated long-run price and income elasticities are -0.147 and 0.429, respectively. {yields} There is evidence of unidirectional long-run causality running from real GDP to crude oil imports.

Asymmetric Vibrations of a Circular Elastic Plate on an Elastic Half Space

DEFF Research Database (Denmark)

Schmidt, H.; Krenk, Steen

1982-01-01

The asymmetric problem of a vibrating circular elastic plate in frictionless contact with an elastic half space is solved by an integral equation method, where the contact stress appears as the unknown function. By a trigonometric expansion, the problem is reduced to a number of uncoupled two...

New approach in evaluation of ceramic-polymer composite bioactivity and biocompatibility.

Science.gov (United States)

Borkowski, Leszek; Sroka-Bartnicka, Anna; Polkowska, Izabela; Pawlowska, Marta; Palka, Krzysztof; Zieba, Emil; Slosarczyk, Anna; Jozwiak, Krzysztof; Ginalska, Grazyna

2017-09-01

Regeneration of bone defects was promoted by a novel β-glucan/carbonate hydroxyapatite composite and characterized by Raman spectroscopy, microCT and electron microscopy. The elastic biomaterial with an apatite-forming ability was developed for bone tissue engineering and implanted into the critical-size defects of rabbits' tibiae. The bone repair process was analyzed on non-decalcified bone/implant sections during a 6-month regeneration period. Using spectroscopic methods, we were able to determine the presence of amides, lipids and assign the areas of newly formed bone tissue. Raman spectroscopy was also used to assess the chemical changes in the composite before and after the implantation process. SEM analyses showed the mineralization degree in the defect area and that the gap size decreased significantly. Microscopic images revealed that the implant debris were interconnected to the poorly mineralized inner side of a new bone tissue. Our study demonstrated that the composite may serve as a biocompatible background for collagen ingrowth and exhibits the advantages of applying Raman spectroscopy, SEM and microCT in studying these samples.

A 3D Orthotropic Strain-Rate Dependent Elastic Damage Material Model.

Energy Technology Data Exchange (ETDEWEB)

English, Shawn Allen

2014-09-01

A three dimensional orthotropic elastic constitutive model with continuum damage and cohesive based fracture is implemented for a general polymer matrix composite lamina. The formulation assumes the possibility of distributed (continuum) damage followed b y localized damage. The current damage activation functions are simply partially interactive quadratic strain criteria . However, the code structure allows for changes in the functions without extraordinary effort. The material model formulation, implementation, characterization and use cases are presented.

Mechanical properties of dense to porous alumina/lanthanum hexaaluminate composite ceramics

International Nuclear Information System (INIS)

Negahdari, Zahra; Willert-Porada, Monika; Pfeiffer, Carolin

2010-01-01

For development of new composite materials based on lanthanum hexaaluminate and alumina ceramics, a better understanding of the microstructure-properties relationship is essential. In this paper, attention was focused on the evaluation of mechanical properties of lanthanum hexaaluminate/alumina particulate composite. It was found out that the lanthanum hexaaluminate content plays a critical role in determination of the microstructure and mechanical properties of the composite ceramics. In situ formation of plate-like lanthanum hexaaluminate in the ceramic matrix was accompanied with formation of pores so that the microstructure shifted from dense to porous. Increasing the lanthanum hexaaluminate content up to a certain value enhanced the fracture toughness, increased the hardness, and increased the elastic modulus of the composite materials. Further increase in the lanthanum hexaaluminate content degraded the hardness as well as the elastic modulus of composite ceramics. The influence of lanthanum hexaaluminate on mechanical properties was described by means of microstructure, porosity, and intrinsic characteristics of lanthanum hexaaluminate.

Effect of a growth hormone treatment on bone orthotropic elasticity in dwarf rats

Science.gov (United States)

Kohles, S. S.; Martinez, D. A.; Bowers, J. R.; Vailas, A. C.; Vanderby, R. Jr

1997-01-01

A refinement of the current ultrasonic elasticity technique was used to measure the orthotropic elastic properties of rat cortical bone as well as to quantify changes in elastic properties, density, and porosity of the dwarf rat cortex after a treatment with recombinant human growth hormone (rhGH). The ultrasonic elasticity technique was refined via optimized signal management of high-frequency wave propagation through cubic cortical specimens. Twenty dwarf rats (37 days old) were randomly assigned to two groups (10 rats each). The dwarf rat model (5-10% of normal GH) was given subcutaneous injections of either rhGH or saline over a 14-day treatment period. Density was measured using Archimedes technique. Porosity and other microstructural characteristics were also explored via scanning electron microscopy and image analysis. Statistical tests verified significant decreases in cortical orthotropic Young's (-26.7%) and shear (-16.7%) moduli and density (-2.42%) concomitant with an increase in porosity (+125%) after rhGH treatments to the dwarf model (p bone properties at this time interval. Structural implications of these changes throughout physiological loading regimens should be explored.

Elasticity of Substitution for Production Functions in Romania and other Countries

Directory of Open Access Journals (Sweden)

Gheorghe Zaman

2007-02-01

Full Text Available The production function is explaining the mechanism through which inputs are changed into outputs and the partial efficiency of labour and capital. It also allows for understanding the elasticity of substitution, which measures the percentage change in factor proportions due to a percentage change in the marginal rate of technical substitution. In this study we have applied the two factor Constant Elasticity of Substitution (CES production function, which is considered to be the generalised form of the Cobb-Douglas function. Using the available statistical data regarding Romania's economy in 1990-1005 period, we have performed time-series and cross-section analysis based on the aggregated production functions at national level.

CARAPACE: a novel composite advanced robotic actuator powering assistive compliant exoskeleton: preliminary design.

Science.gov (United States)

Masia, Lorenzo; Cappello, Leonardo; Morasso, Pietro; Lachenal, Xavier; Pirrera, Alberto; Weaver, Paul; Mattioni, Filippo

2013-06-01

A novel actuator is introduced that combines an elastically compliant composite structure with conventional electromechanical elements. The proposed design is analogous to that used in Series Elastic Actuators, its distinctive feature being that the compliant composite part offers different stable configurations. In other words, its elastic potential presents points of local minima that correspond to robust stable positions (multistability). This potential is known a priori as a function of the structural geometry, thus providing tremendous benefits in terms of control implementation. Such knowledge enables the complexities arising from the additional degrees of freedom associated with link deformations to be overcome and uncover challenges that extends beyond those posed by standard rigidlink robot dynamics. It is thought that integrating a multistable elastic element in a robotic transmission can provide new scenarios in the field of assistive robotics, as the system may help a subject to stand or carry a load without the need for an active control effort by the actuators.

Theoretical and experimental determination of mechanical properties of superconducting composite wire

International Nuclear Information System (INIS)

Gray, W.H.; Sun, C.T.

1976-07-01

The mechanical properties of a composite superconducting (NbTi/Cu) wire are characterized in terms of the mechanical properties of each constituent material. For a particular composite superconducting wire, five elastic material constants were experimentally determined and theoretically calculated. Since the Poisson's ratios for the fiber and the matrix material were very close, there was essentially no (less than 1 percent) difference among all the theoretical predictions for any individual mechanical constant. Because of the expense and difficulty of producing elastic constant data of 0.1 percent accuracy, and therefore conclusively determining which theory is best, no further experiments were performed

Effect of alloying on elastic properties of ZrN based transition metal nitride alloys

KAUST Repository

Kanoun, Mohammed; Goumri-Said, Souraya

2014-01-01

We report the effect of composition and metal sublattice substitutional element on the structural, elastic and electronic properties of ternary transition metal nitrides Zr1-xMxN with M=Al, Ti, Hf, V, Nb, W and Mo. The analysis of the elastic constants, bulk modulus, shear modulus, Young's modulus, and Poisson's ratio provides insights regarding the mechanical behavior of Zr1-xMxN. We predict that ternary alloys are more ductile compared to their parent binary compounds. The revealed trend in the mechanical behavior might help for experimentalists on the ability of tuning the mechanical properties during the alloying process by varying the concentration of the transition metal. © 2014 Elsevier B.V.

Effect of alloying on elastic properties of ZrN based transition metal nitride alloys

KAUST Repository

Kanoun, Mohammed

2014-09-01

We report the effect of composition and metal sublattice substitutional element on the structural, elastic and electronic properties of ternary transition metal nitrides Zr1-xMxN with M=Al, Ti, Hf, V, Nb, W and Mo. The analysis of the elastic constants, bulk modulus, shear modulus, Young\\'s modulus, and Poisson\\'s ratio provides insights regarding the mechanical behavior of Zr1-xMxN. We predict that ternary alloys are more ductile compared to their parent binary compounds. The revealed trend in the mechanical behavior might help for experimentalists on the ability of tuning the mechanical properties during the alloying process by varying the concentration of the transition metal. © 2014 Elsevier B.V.

Phase stability and elastic properties of β Ti-Nb-X (X = Zr, Sn) alloys: an ab initio density functional study

Science.gov (United States)

K, Rajamallu; Niranjan, Manish K.; Ameyama, Kei; Dey, Suhash R.

2017-12-01

Alloying effects of Zr and Sn on β phase stability and elastic properties in Ti-Nb alloys are investigated within the framework of first-principles density functional theory. Our results suggest that the stability of β phase can be significantly enhanced by the addition of Zr and Sn in Ti-Nb alloys. The computed results indicate that Zr and Sn behave as strong β stabilizers in the Ti-Nb system. The elastic properties are found to be altered considerably by the addition of ternary alloying elements (Zr and Sn). The computed elastic moduli of Ti18.75 at%Nb6.25 at%Zr and Ti25 at%NbxZr compositions are found to be lower than that for Ti18.75 at%Nb6.25 at%Sn and Ti25 at%NbxSn system. The lowest value of ˜54 GPa is obtained for Ti25 at%Nb6.25 at%Zr composition. Furthermore, the directional Young’s modulus is found to be in the order of E 100 system.

Elastic least-squares reverse time migration

KAUST Repository

Feng, Zongcai; Schuster, Gerard T.

2016-01-01

Elastic least-squares reverse time migration (LSRTM) is used to invert synthetic particle-velocity data and crosswell pressure field data. The migration images consist of both the P- and Svelocity perturbation images. Numerical tests on synthetic and field data illustrate the advantages of elastic LSRTM over elastic reverse time migration (RTM). In addition, elastic LSRTM images are better focused and have better reflector continuity than do the acoustic LSRTM images.

Elastic least-squares reverse time migration

KAUST Repository

Feng, Zongcai

2016-09-06

Elastic least-squares reverse time migration (LSRTM) is used to invert synthetic particle-velocity data and crosswell pressure field data. The migration images consist of both the P- and Svelocity perturbation images. Numerical tests on synthetic and field data illustrate the advantages of elastic LSRTM over elastic reverse time migration (RTM). In addition, elastic LSRTM images are better focused and have better reflector continuity than do the acoustic LSRTM images.

Coupled Thermo-Electro-Magneto-Elastic Response of Smart Stiffened Panels

Science.gov (United States)

Bednarcyk, Brett A.; Yarrington, Phillip W.

2009-01-01

This report documents the procedures developed for incorporating smart laminate and panel analysis capabilities within the HyperSizer aerospace structural sizing software package. HyperSizer analyzes stiffened panels composed of arbitrary composite laminates through stiffener homogenization, or "smearing " techniques. The result is an effective constitutive equation for the stiffened panel that is suitable for use in a full vehicle-scale finite element analysis via MSC/NASTRAN. The existing thermo-elastic capabilities of HyperSizer have herein been extended to include coupled thermo-electro-magneto-elastic analysis capabilities. This represents a significant step toward realization of design tools capable of guiding the development of the next generation of smart aerospace structures. Verification results are presented that compare the developed smart HyperSizer capability with an ABAQUS piezoelectric finite element solution for a facesheet-flange combination. These results show good agreement between HyperSizer and ABAQUS, but highlight a limitation of the HyperSizer formulation in that constant electric field components are assumed.

Relationship between the Uncompensated Price Elasticity and the Income Elasticity of Demand under Conditions of Additive Preferences.

Science.gov (United States)

Sabatelli, Lorenzo

2016-01-01

Income and price elasticity of demand quantify the responsiveness of markets to changes in income and in prices, respectively. Under the assumptions of utility maximization and preference independence (additive preferences), mathematical relationships between income elasticity values and the uncompensated own and cross price elasticity of demand are here derived using the differential approach to demand analysis. Key parameters are: the elasticity of the marginal utility of income, and the average budget share. The proposed method can be used to forecast the direct and indirect impact of price changes and of financial instruments of policy using available estimates of the income elasticity of demand.

Fully coupled heat conduction and deformation analyses of nonlinear viscoelastic composites

KAUST Repository

Khan, Kamran

2012-05-01

This study presents an integrated micromechanical model-finite element framework for analyzing coupled heat conduction and deformations of particle-reinforced composite structures. A simplified micromechanical model consisting of four sub-cells, i.e., one particle and three matrix sub-cells is formulated to obtain the effective thermomechanical properties and micro-macro field variables due to coupled heat conduction and nonlinear thermoviscoelastic deformation of a particulate composite that takes into account the dissipation of energy from the viscoelastic constituents. A time integration algorithm for simultaneously solving the equations that govern heat conduction and thermoviscoelastic deformations of isotropic homogeneous materials is developed. The algorithm is then integrated to the proposed micromechanical model. A significant temperature generation due to the dissipation effect in the viscoelastic matrix was observed when the composite body is subjected to cyclic mechanical loadings. Heat conduction due to the dissipation of the energy cannot be ignored in predicting the factual temperature and deformation fields within the composite structure, subjected to cyclic loading for a long period. A higher creep resistant matrix material or adding elastic particles can lower the temperature generation. Our analyses suggest that using particulate composites and functionally graded materials can reduce the heat generation due to energy dissipation. © 2012 Elsevier Ltd.

Poisson's ratio of fiber-reinforced composites

Science.gov (United States)

Christiansson, Henrik; Helsing, Johan

1996-05-01

Poisson's ratio flow diagrams, that is, the Poisson's ratio versus the fiber fraction, are obtained numerically for hexagonal arrays of elastic circular fibers in an elastic matrix. High numerical accuracy is achieved through the use of an interface integral equation method. Questions concerning fixed point theorems and the validity of existing asymptotic relations are investigated and partially resolved. Our findings for the transverse effective Poisson's ratio, together with earlier results for random systems by other authors, make it possible to formulate a general statement for Poisson's ratio flow diagrams: For composites with circular fibers and where the phase Poisson's ratios are equal to 1/3, the system with the lowest stiffness ratio has the highest Poisson's ratio. For other choices of the elastic moduli for the phases, no simple statement can be made.

Fracture toughness in metal matrix composites

Directory of Open Access Journals (Sweden)

Perez Ipiña J.E.

2000-01-01

Full Text Available Evaluations of the fracture toughness in metal matrix composites (Duralcan reinforced with 15% of Al(20(3 and SiC are presented in this work. The application of Elastic Plastic Fracture Mechanics is discussed and the obtained values are compared with the ones obtained by means of Linear Elastic Fracture Mechanics. Results show that J IC derived K JC values are higher than the corresponding values obtained by direct application of the linear elastic methodology. The effect of a heat treatment on the material fracture toughness was also evaluated in which the analyzed approaches showed, not only different toughness values, but also opposite tendencies. A second comparison of the J IC and K JC values obtained in this work with toughness values reported in the literature is presented and discussed.

Thermo-elastic optical coherence tomography.

Science.gov (United States)

Wang, Tianshi; Pfeiffer, Tom; Wu, Min; Wieser, Wolfgang; Amenta, Gaetano; Draxinger, Wolfgang; van der Steen, Antonius F W; Huber, Robert; Soest, Gijs van

2017-09-01

The absorption of nanosecond laser pulses induces rapid thermo-elastic deformation in tissue. A sub-micrometer scale displacement occurs within a few microseconds after the pulse arrival. In this Letter, we investigate the laser-induced thermo-elastic deformation using a 1.5 MHz phase-sensitive optical coherence tomography (OCT) system. A displacement image can be reconstructed, which enables a new modality of phase-sensitive OCT, called thermo-elastic OCT. An analysis of the results shows that the optical absorption is a dominating factor for the displacement. Thermo-elastic OCT is capable of visualizing inclusions that do not appear on the structural OCT image, providing additional tissue type information.

An analytical solution for the magneto-electro-elastic bimorph beam forced vibrations problem

International Nuclear Information System (INIS)

Milazzo, A; Orlando, C; Alaimo, A

2009-01-01

Based on the Timoshenko beam theory and on the assumption that the electric and magnetic fields can be treated as steady, since elastic waves propagate very slowly with respect to electromagnetic ones, a general analytical solution for the transient analysis of a magneto-electro-elastic bimorph beam is obtained. General magneto-electric boundary conditions can be applied on the top and bottom surfaces of the beam, allowing us to study the response of the bilayer structure to electromagnetic stimuli. The model reveals that the magneto-electric loads enter the solution as an equivalent external bending moment per unit length and as time-dependent mechanical boundary conditions through the definition of the bending moment. Moreover, the influences of the electro-mechanic, magneto-mechanic and electromagnetic coupling on the stiffness of the bimorph stem from the computation of the beam equivalent stiffness constants. Free and forced vibration analyses of both multiphase and laminated magneto-electro-elastic composite beams are carried out to check the effectiveness and reliability of the proposed analytic solution

Teaching nonlinear dynamics through elastic cords

International Nuclear Information System (INIS)

Chacon, R; Galan, C A; Sanchez-Bajo, F

2011-01-01

We experimentally studied the restoring force of a length of stretched elastic cord. A simple analytical expression for the restoring force was found to fit all the experimental results for different elastic materials. Remarkably, this analytical expression depends upon an elastic-cord characteristic parameter which exhibits two limiting values corresponding to two nonlinear springs with different Hooke's elastic constants. Additionally, the simplest model of elastic cord dynamics is capable of exhibiting a great diversity of nonlinear phenomena, including bifurcations and chaos, thus providing a suitable alternative model system for discussing the basic essentials of nonlinear dynamics in the context of intermediate physics courses at university level.

Elastic Beanstalk

CERN Document Server

Vliet, Jurg; Wel, Steven; Dowd, Dara

2011-01-01

While it's always been possible to run Java applications on Amazon EC2, Amazon's Elastic Beanstalk makes the process easier-especially if you understand how it works beneath the surface. This concise, hands-on book not only walks you through Beanstalk for deploying and managing web applications in the cloud, you'll also learn how to use this AWS tool in other phases of development. Ideal if you're a developer familiar with Java applications or AWS, Elastic Beanstalk provides step-by-step instructions and numerous code samples for building cloud applications on Beanstalk that can handle lots

Early experience with titanium elastic nails in a trauma unit.

LENUS (Irish Health Repository)

Shah, M H

2012-02-03

The Titanium Elastic Nail (TEN) offers a number of potential advantages over traditional ways of treating long bone fractures particularly in the paediatric population. These advantages include earlier mobilisation and shorter hospital stay and less risk of loss of fracture position. These advantages are most apparent and significant when treating femoral fractures in children where the length of hospital stay is reduced from several weeks to a typical period of 5 to 8 days. We have reviewed our early experience of using these implants over the past 2 years. Patients were assessed clinically and radiologically. 13 patients were treated using the TEN during this period. There were 2 femoral fractures, 4 humeral fractures, 1 tibial and 6 forearm fractures treated using the Titanium Elastic Nail. All fractures united during the study period. However 1 humeral fracture required a secondary bone grafting and plating for delayed union and 1 fracture lost position during follow-up. Insertion point pain was a problem in 4 patients but this resolved after nail removal in all. There was 1 superficial wound infection which resolved with antibiotics and 1 superficial wound infection of an open fracture wound which resolved following nail removal and antibiotics. There were no cases of deep infection. There were no limb length discrepancy or rotational or angular malalignment problems. Biomechanical principles and technical aspects of this type of fixation are discussed.

Positron interactions with water–total elastic, total inelastic, and elastic differential cross section measurements

International Nuclear Information System (INIS)

Tattersall, Wade; Chiari, Luca; Machacek, J. R.; Anderson, Emma; Sullivan, James P.; White, Ron D.; Brunger, M. J.; Buckman, Stephen J.; Garcia, Gustavo; Blanco, Francisco

2014-01-01

Utilising a high-resolution, trap-based positron beam, we have measured both elastic and inelastic scattering of positrons from water vapour. The measurements comprise differential elastic, total elastic, and total inelastic (not including positronium formation) absolute cross sections. The energy range investigated is from 1 eV to 60 eV. Comparison with theory is made with both R-Matrix and distorted wave calculations, and with our own application of the Independent Atom Model for positron interactions

Substitution elasticities between GHG-polluting and nonpolluting inputs in agricultural production: A meta-regression

International Nuclear Information System (INIS)

Liu, Boying; Richard Shumway, C.

2016-01-01

This paper reports meta-regressions of substitution elasticities between greenhouse gas (GHG) polluting and nonpolluting inputs in agricultural production, which is the main feedstock source for biofuel in the U.S. We treat energy, fertilizer, and manure collectively as the “polluting input” and labor, land, and capital as nonpolluting inputs. We estimate meta-regressions for samples of Morishima substitution elasticities for labor, land, and capital vs. the polluting input. Much of the heterogeneity of Morishima elasticities can be explained by type of primal or dual function, functional form, type and observational level of data, input categories, number of outputs, type of output, time period, and country categories. Each estimated long-run elasticity for the reference case, which is most relevant for assessing GHG emissions through life-cycle analysis, is greater than 1.0 and significantly different from zero. Most predicted long-run elasticities remain significantly different from zero at the data means. These findings imply that life-cycle analysis based on fixed proportion production functions could provide grossly inaccurate measures of GHG of biofuel. - Highlights: • This paper reports meta-regressions of substitution elasticities between greenhouse-gas (GHG) polluting and nonpolluting inputs in agricultural production, which is the main feedstock source for biofuel in the U.S. • We estimate meta-regressions for samples of Morishima substitution elasticities for labor, land, and capital vs. the polluting input based on 65 primary studies. • We found that each estimated long-run elasticity for the reference case, which is most relevant for assessing GHG emissions through life-cycle analysis, is greater than 1.0 and significantly different from zero. Most predicted long-run elasticities remain significantly different from zero at the data means. • These findings imply that life-cycle analysis based on fixed proportion production functions could

Hardrock Elastic Physical Properties: Birch's Seismic Parameter Revisited

Science.gov (United States)

Wu, M.; Milkereit, B.

2014-12-01

Identifying rock composition and properties is imperative in a variety of fields including geotechnical engineering, mining, and petroleum exploration, in order to accurately make any petrophysical calculations. Density is, in particular, an important parameter that allows us to differentiate between lithologies and estimate or calculate other petrophysical properties. It is well established that compressional and shear wave velocities of common crystalline rocks increase with increasing densities (i.e. the Birch and Nafe-Drake relationships). Conventional empirical relations do not take into account S-wave velocity. Physical properties of Fe-oxides and massive sulfides, however, differ significantly from the empirical velocity-density relationships. Currently, acquiring in-situ density data is challenging and problematic, and therefore, developing an approximation for density based on seismic wave velocity and elastic moduli would be beneficial. With the goal of finding other possible or better relationships between density and the elastic moduli, a database of density, P-wave velocity, S-wave velocity, bulk modulus, shear modulus, Young's modulus, and Poisson's ratio was compiled based on a multitude of lab samples. The database is comprised of isotropic, non-porous metamorphic rock. Multi-parameter cross plots of the various elastic parameters have been analyzed in order to find a suitable parameter combination that reduces high density outliers. As expected, the P-wave velocity to S-wave velocity ratios show no correlation with density. However, Birch's seismic parameter, along with the bulk modulus, shows promise in providing a link between observed compressional and shear wave velocities and rock densities, including massive sulfides and Fe-oxides.

Lamb Wave Assessment of Fatigue and Thermal Damage in Composites

Science.gov (United States)

Seale, Michael D.; Smith, Barry T.; Prosser, W. H.

2004-01-01

Among the various techniques available, ultrasonic Lamb waves offer a convenient method of evaluating composite materials. Since the Lamb wave velocity depends on the elastic properties of a structure, an effective tool exists to monitor damage in composites by measuring the velocity of these waves. Lamb wave measurements can propagate over long distances and are sensitive to the desired in-plane elastic properties of the material. This paper describes two studies which monitor fatigue damage and two studies which monitor thermal damage in composites using Lamb waves. In the fatigue studies, the Lamb wave velocity is compared to modulus measurements obtained using strain gage measurements in the first experiment and the velocity is monitored along with the crack density in the second. In the thermal damage studies, one examines samples which were exposed to varying temperatures for a three minute duration and the second includes rapid thermal damage in composites by intense laser beams. In all studies, the Lamb wave velocity is demonstrated to be an excellent method to monitor damage in composites.

High-Temperature Elasticity of Topaz: A Resonant Ultrasound Spectroscopic study

Science.gov (United States)

Tennakoon, S.; Peng, Y.; Andreu, L.; Rivera, F.; Mookherjee, M.; Manthilake, G.; Speziale, S.

2017-12-01

Topaz (Al2SiO4(F,OH)2) is a hydrous aluminosilicate mineral stable in the hydrated sediments in subduction zone settings and could transport water into the Earth's interior. To constrain the amount of water subducted, it is important to have a better understanding of the elastic constants of hydrous phases and compare them with the geophysical observations. In this study, we explored the full elastic moduli tensor for a single crystal topaz using Resonant Ultrasound Spectroscopy. We determined the full elastic moduli tensor at ambient conditions (1 bar and 297 K), with the principal components- C11, C22, and C33 are 279, 352 and 288 GPa respectively, the off-diagonal components- C­12, C13, and C23 are 124, 72, and 82 GPa respectively, and the shear components- C44, C55, and C66 are 111, 134, and 130 GPa respectively. The compressional (AVP) and shear (AVS) anisotropy for topaz are 13 and 14 % respectively. The aggregate bulk (K) and shear (G) moduli are 162 and 117 GPa respectively. We determined the elasticity of topaz up to 1000 K. The components of the full elastic moduli tensor show softening at high temperature. Temperature derivatives of sound velocity of topaz, dVP/dT = -3.5 ×10-4 km/s/K and dVS/dT = -2.2 ×10-4 km/s/K are smaller than those for corundum [1], α-quartz [2], and olivine [3]. In contrast, the temperature derivatives of primary and shear sound velocity for topaz is greater than that of pyrope garnet [4]. The elasticity and sound velocity of topaz also vary as a function of chemistry i.e., OH-F contents. Our study demonstrates that the effect of composition (xOH) on the velocity is more pronounced than that of temperature.Acknowledgement: This study is supported by US NSF awards EAR-1634422. Reference: [1] Goto, T. et al.,1989, J. Geophys. Res., 94, 7588; [2] Ohno, I. et al., 2006, Phys. Chem. Miner., 33, 1-9; [3] Isaak, D. G., 1992, J. Geophys. Res. Solid Earth, 97, 1871-1885; [4] Sinogeikin, S. V., Bass, J. D., 2002, Earth Planet. Sci. Lett

Design and tailoring of Ni-Sn-W composites for bonded abrasive applications

Energy Technology Data Exchange (ETDEWEB)

Kourtoukova, G.L.; Demetry, C.; Biederman, R.R. [Worcester Polytechnic Inst., MA (United States). Materials Science and Engineering Program; Ramanath, S.; Andrews, R.M.; Jacobs, D.S. [Saint-Gobain/Norton Company, Worcester, MA (United States)

2000-01-15

The combination of properties ideal for metal bonds in abrasive products can rarely be achieved in a monolithic material. This research demonstrates a successful approach for producing a composite bond with higher elastic modulus without a significant increase in wear resistance, by taking advantage of the reaction between matrix and reinforcement to produce intermetallics. Composites comprised of a Ni-Sn matrix with continuous W fiber and/or W powder dispersoid were prepared by powder metallurgy methods. Composite specimens densified by hot pressing were characterized with a combination of scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) analyses, measurements of wear resistance, and measurements of Young's modulus and hardness by both bulk and nanoindentation methods. A significant stiffening effect was observed; the elastic modulus of the composites was up to 30% greater than that predicted by a rule of mixtures based on the moduli of the unreacted fiber and matrix constituents alone. As desired, the wear resistance of the composite was approximately equal to that of the Ni-Sn matrix. One contribution to this combination of properties is believed to be the high elastic moduli and likely low fracture toughness of the Ni-W and Ni-Sn intermetallics that are formed. Properties of the Ni-Sn-W composites are contrasted with those of a Ni-Sn matrix reinforced with WC particulate, where no reaction occurs at the interface. (orig.)

Photoelectron angular distribution from free SiO2 nanoparticles as a probe of elastic electron scattering.

Science.gov (United States)

Antonsson, E; Langer, B; Halfpap, I; Gottwald, J; Rühl, E

2017-06-28

In order to gain quantitative information on the surface composition of nanoparticles from X-ray photoelectron spectroscopy, a detailed understanding of photoelectron transport phenomena in these samples is needed. Theoretical results on the elastic and inelastic scattering have been reported, but a rigorous experimental verification is lacking. We report in this work on the photoelectron angular distribution from free SiO 2 nanoparticles (d = 122 ± 9 nm) after ionization by soft X-rays above the Si 2p and O 1s absorption edges, which gives insight into the relative importance of elastic and inelastic scattering channels in the sample particles. The photoelectron angular anisotropy is found to be lower for photoemission from SiO 2 nanoparticles than that expected from the theoretical values for the isolated Si and O atoms in the photoelectron kinetic energy range 20-380 eV. The reduced angular anisotropy is explained by elastic scattering of the outgoing photoelectrons from neighboring atoms, smearing out the atomic distribution. Photoelectron angular distributions yield detailed information on photoelectron elastic scattering processes allowing for a quantification of the number of elastic scattering events the photoelectrons have undergone prior to leaving the sample. The interpretation of the experimental photoelectron angular distributions is complemented by Monte Carlo simulations, which take inelastic and elastic photoelectron scattering into account using theoretical values for the scattering cross sections. The results of the simulations reproduce the experimental photoelectron angular distributions and provide further support for the assignment that elastic and inelastic electron scattering processes need to be considered.

Influence of different beverages on the force degradation of intermaxillary elastics: an in vitro study

Directory of Open Access Journals (Sweden)

Jorge César Borges Leão Filho

2013-04-01

Full Text Available Objective: The aim of this study was to evaluate in vitro the effects of frequently ingested beverages on force degradation of intermaxillary elastics. Material and Methods: One hundred and eighty 1/4-inch intermaxillary elastics (TP Orthodontics were immersed into six different beverages: (1 Coca-Cola®; (2 Beer; (3 Orange juice; (4 Red wine; (5 Coffee and (6 artificial saliva (control. The period of immersion was 15 min for the first and second cycles and 30 min for the third to fifth cycles. Tensile forces were read in a tensile testing machine before and after the five immersion cycles. One-way repeated measures ANOVA was used to identify significant differences. Results: Force degradation was seen in all evaluated groups and at all observation periods (p<0.05. A greater degree of degradation was present at the initial periods, decreasing gradually over time. However, no statistically significant differences were seen among groups at the same periods, showing that different groups behaved similarly. Conclusions: The chemical nature of the evaluated beverages was not able to influence the degree of force degradation at all observation periods.

Relationship between the Uncompensated Price Elasticity and the Income Elasticity of Demand under Conditions of Additive Preferences.

Directory of Open Access Journals (Sweden)

Lorenzo Sabatelli

Full Text Available Income and price elasticity of demand quantify the responsiveness of markets to changes in income and in prices, respectively. Under the assumptions of utility maximization and preference independence (additive preferences, mathematical relationships between income elasticity values and the uncompensated own and cross price elasticity of demand are here derived using the differential approach to demand analysis. Key parameters are: the elasticity of the marginal utility of income, and the average budget share. The proposed method can be used to forecast the direct and indirect impact of price changes and of financial instruments of policy using available estimates of the income elasticity of demand.

Assessment of climate change impacts on runoff in China using climate elasticity and multiple CMIP5 GCMs

Science.gov (United States)

Wu, C.; Hu, B. X.; Wang, P.; Xu, K.

2017-12-01

The occurrence of climate warming is unequivocal and is expected to alter the temporal-spatial patterns of regional water resources. Based on the long-term (1960-2012) water budget data and climate projections from 28 Global Climate Models (GCMs) of the Coupled Model Intercomparison Project Phase 5 (CMIP5), this study investigated the responses of runoff (R) to future climate variability in China at both grid and catchment scales using the Budyko-based elasticity method. Results indicate a large spatial variation in precipitation (P) elasticity (from 1.2 to 3.3) and potential evaporation (PET) elasticity (from -2.3 to -0.2) across China. The P elasticity is larger in northeast and western China than in southern China, while the opposite occurs for PET elasticity. Climate projections suggest that there is large uncertainty involved among the GCM simulations, but most project a consistent change in P (or PET) over China at the mean annual scale. During the future period of 2071-2100, the mean annual P will likely increase in most parts of China particularly the western regions, while the mean annual PET will likely increase in the whole China especially the southern regions due to future increases in temperature. Moreover, larger increases are projected for higher emission scenarios. Compared with the baseline 1971-2000, the arid regions and humid regions of China will likely become wetter and drier in the period 2071-2100, respectively.

Phase Stability and Elasticity of TiAlN

Directory of Open Access Journals (Sweden)

Magnus Odén

2011-09-01

Full Text Available We review results of recent combined theoretical and experimental studies of Ti1−xAlxN, an archetypical alloy system material for hard-coating applications. Theoretical simulations of lattice parameters, mixing enthalpies, and elastic properties are presented. Calculated phase diagrams at ambient pressure, as well as at pressure of 10 GPa, show a wide miscibility gap and broad region of compositions and temperatures where the spinodal decomposition takes place. The strong dependence of the elastic properties and sound wave anisotropy on the Al-content offers detailed understanding of the spinodal decomposition and age hardening in Ti1−xAlxN alloy films and multilayers. TiAlN/TiN multilayers can further improve the hardness and thermal stability compared to TiAlN since they offer means to influence the kinetics of the favorable spinodal decomposition and suppress the detrimental transformation to w-AlN. Here, we show that a 100 degree improvement in terms of w-AlN suppression can be achieved, which is of importance when the coating is used as a protective coating on metal cutting inserts.

A homogenization method for ductile-brittle composite laminates at large deformations

DEFF Research Database (Denmark)

Poulios, Konstantinos; Niordson, Christian Frithiof

2018-01-01

-elastic behavior in the reinforcement as well as for the bending stiffness of the reinforcement layers. Additionally to previously proposed models, the present method includes Lemaitre type damage for the reinforcement, making it applicable to a wider range of engineering applications. The capability...... of the proposed method in representing the combined effect of plasticity, damage and buckling at microlevel within a homogenized setting is demonstrated by means of direct comparisons to a reference discrete model.......This paper presents a high fidelity homogenization method for periodically layered composite structures that accounts for plasticity in the matrix material and quasi-brittle damage in the reinforcing layers, combined with strong geometrical nonlinearities. A set of deliberately chosen internal...

Optimization of micro and nanoimprint de-embossing by elastic fracture modelling

OpenAIRE

Balla, Tobias; Spearing, Simon Mark

2013-01-01

A semi-analytical model is presented for the de-embossing phase of the nanoimprint patterning process. The model is based on established principles of elastic fracture mechanics as developed for fibre-bridged cracking in composites. De-embossing is idealized as a steady-state fracture process, which enables the energy change to be considered by reference to a unit cell of a cylindrical polymer post, de-embossing from an axisymmetric stamp. The model provides predictions of the achievable limi...

Elastic band prediction equations for combined free-weight and elastic band bench presses and squats.

Science.gov (United States)

Shoepe, Todd C; Ramirez, David A; Almstedt, Hawley C

2010-01-01

Elastic bands added to traditional free-weight techniques have become a part of suggested training routines in recent years. Because of the variable loading patterns of elastic bands (i.e., greater stretch produces greater resistance), it is necessary to quantify the exact loading patterns of bands to identify the volume and intensity of training. The purpose of this study was to determine the length vs. tension properties of multiple sizes of a set of commonly used elastic bands to quantify the resistance that would be applied to free-weight plus elastic bench presses (BP) and squats (SQ). Five elastic bands of varying thickness were affixed to an overhead support beam. Dumbbells of varying weights were progressively added to the free end while the linear deformation was recorded with each subsequent weight increment. The resistance was plotted as a factor of linear deformation, and best-fit nonlinear logarithmic regression equations were then matched to the data. For both the BP and SQ loading conditions and all band thicknesses tested, R values were greater than 0.9623. These data suggest that differences in load exist as a result of the thickness of the elastic band, attachment technique, and type of exercise being performed. Facilities should adopt their own form of loading quantification to match their unique set of circumstances when acquiring, researching, and implementing elastic band and free-weight exercises into the training programs.

Homogenized Finite Element Analysis on Effective Elastoplastic Mechanical Behaviors of Composite with Imperfect Interfaces

Directory of Open Access Journals (Sweden)

Wu-Gui Jiang

2014-12-01

Full Text Available A three-dimensional (3D representative volume element (RVE model was developed for analyzing effective mechanical behavior of fiber-reinforced ceramic matrix composites with imperfect interfaces. In the model, the fiber is assumed to be perfectly elastic until its tensile strength, and the ceramic material is modeled by an elasto-plastic Drucker-Prager constitutive law. The RVE model is then used to study the elastic properties and the tensile strength of composites with imperfect interfaces and validated through experiments. The imperfect interfaces between the fiber and the matrix are taken into account by introducing some cohesive contact surfaces. The influences of the interface on the elastic constants and the tensile strengths are examined through these interface models.

Nonlinear Dispersive Elastic Waves in Solids: Exact, Approximate, and Numerical Solutions

Science.gov (United States)

Khajehtourian, Romik

Wave motion lies at the heart of many disciplines in the physical sciences and engineering. For example, problems and applications involving light, sound, heat, or fluid flow are all likely to involve wave dynamics at some level. A particular class of problems is concerned with the propagation of elastic waves in a solid medium, such as a fiber-reinforced composite material responding to vibratory excitations, or soil and rock admitting seismic waves moments after the onset of an earthquake, or phonon transport in a semiconducting crystal like silicon. Regardless of the type of wave, the dispersion relation provides a fundamental characterization of the elastodynamic properties of the medium. The first part of the dissertation examines the propagation of a large-amplitude elastic wave in a one-dimensional homogeneous medium with a focus on the effects of inherent nonlinearities on the dispersion relation. Considering a thin rod, where the thickness is small compared to the wavelength, an exact, closed-form formulation is presented for the treatment of two types of nonlinearity in the strain-displacement gradient relation: Green-Lagrange and Hencky. The derived relation is then verified by direct time-domain simulations, examining both instantaneous dispersion (by direct observation) and short-term, pre-breaking dispersion (by Fourier transformation). A high-order perturbation analysis is also conducted yielding an explicit analytical space-time solution, which is shown to be spectrally accurate. The results establish a perfect match between theory and simulation and reveal that regardless of the strength of the nonlinearity, the dispersion relation fully embodies all information pertaining to the nonlinear harmonic generation mechanism that unfolds as an arbitrary-profiled wave evolves in the medium. In the second part of the dissertation, the analysis is extended to a continuous periodic thin rod exhibiting multiple phases or embedded local resonators. The

Comparison between published clinical success of direct resin composite restorations in vital posterior teeth in 1995-2005 and 2006-2016 periods.

Science.gov (United States)

Alvanforoush, N; Palamara, J; Wong, R H; Burrow, M F

2017-06-01

Composites are increasing in popularity as restorative materials. This growing role indicates the necessity of studies on their clinical outcome. In this study, clinical studies published on the performance of posterior composite restorations were included except those of less than a 24-month assessment period. Results of non-vital, anterior or primary teeth and cervical single-surface restorations were also excluded. Records about composite type, number of final recall restorations, failure/survival rate, assessment period and failure reasons were analysed for each decade. Overall survival/failure rates for studies in 1995-2005 were 89.41%/10.59% and for 2006-2016 were 86.87%/13.13%, respectively. In 1995-2005, the reasons for failure were secondary caries (29.47%) and composite fracture (28.84%) with low tooth fracture (3.45%) compared with reasons of failure in 2006-2016, which were secondary caries (25.68%), composite fracture (39.07%), and tooth fracture (23.76%). An increase in incidence of composite fracture, tooth fracture and need for endodontic treatment as failure reasons was noted in the latter decade in addition to a decrease in secondary caries, postoperative sensitivity, unsatisfactory marginal adaptation and wear. The overall rates of failure showed little difference, but the causes showed a notable change. This is believed to be a reflection of increased use of composites for larger restorations and possibly changes of material characteristics. © 2016 Australian Dental Association.

Elastic and Strength Properties of Heat-Treated Beech and Birch Wood

Directory of Open Access Journals (Sweden)

Vlastimil Borůvka

2018-04-01

Full Text Available This paper deals with the impact of heat treatment on the elastic and strength properties of two diffuse porous hardwoods, namely Fagus sylvatica and Betula pendula. Two degrees of the heat treatment were used at temperatures of 165 °C and 210 °C. The dynamic and static elasticity modulus, bending strength, impact toughness, hardness, and density were tested. It is already known that an increase in treatment temperature decreases the mechanical properties and, on the other hand, leads to a better shape and dimensional stability. Higher temperatures of the heat treatment correlated with lower elastic and strength properties. In the case of higher temperature treatments, the decline of tested properties was noticeable as a result of serious changes in the chemical composition of wood. It was confirmed that at higher temperature stages of treatment, there was a more pronounced decrease in beech properties compared to those of the birch, which was the most evident in their bending strength and hardness. Our research confirmed that there is no reason to consider birch wood to be of a lesser quality, although it is regarded by foresters as an inferior tree species. After the heat treatment, the wood properties are almost the same as in the case of beech wood.

FOAMED CEMENT COMPOSITES: DETECTION OF THE MODULUS OF ELASTICITY USING DIC ANALYSIS AND COMPARISON WITH OTHER METHODS

Directory of Open Access Journals (Sweden)

Jakub Ďureje

2017-11-01

Full Text Available A modulus of elasticity was determined for eight differently foamed cement paste samples. Samples were loaded in the laboratory by a hydraulic press. The force acting on the sample was read directly from the laboratory press. Digital Image Correlation (DIC analysis were used to draw deformations. Before loading pressure test was applied a random contrast pattern to the samples. Samples were captured by the camera in a one-second interval during the loading pressure test. The images were edited in the Adobe Photoshop Lightroom and then evaluated using Ncorr software. The result is a vertical and horizontal shift field. On the basis of the results obtained, it was possible to calculate the modulus of elasticity of each sample.

Growth-induced axial buckling of a slender elastic filament embedded in an isotropic elastic matrix

KAUST Repository

O'Keeffe, Stephen G.

2013-11-01

We investigate the problem of an axially loaded, isotropic, slender cylinder embedded in a soft, isotropic, outer elastic matrix. The cylinder undergoes uniform axial growth, whilst both the cylinder and the surrounding elastic matrix are confined between two rigid plates, so that this growth results in axial compression of the cylinder. We use two different modelling approaches to estimate the critical axial growth (that is, the amount of axial growth the cylinder is able to sustain before it buckles) and buckling wavelength of the cylinder. The first approach treats the filament and surrounding matrix as a single 3-dimensional elastic body undergoing large deformations, whilst the second approach treats the filament as a planar, elastic rod embedded in an infinite elastic foundation. By comparing the results of these two approaches, we obtain an estimate of the foundation modulus parameter, which characterises the strength of the foundation, in terms of the geometric and material properties of the system. © 2013 Elsevier Ltd. All rights reserved.

EVALUATION OF EFFECTIVE PROPERTIES OF BASALT TEXTILE REINFORCED CERAMIC MATRIX COMPOSITES

Directory of Open Access Journals (Sweden)

Soňa Valentová

2017-11-01

Full Text Available The present paper is concerned with the analysis of a ceramic matrix composite, more specifically the plain weave textile fabric composite made of basalt fibers embedded into the pyrolyzed polysiloxane matrix. Attention is paid to the determination of effective elastic properties of the yarn via homogenization based on the Mori-Tanaka averaging scheme and the 1st order numerical homogenization method adopting a suitable representative computational model. The latter approach is then employed to simulate the response of the yarn when loaded beyond the elastic limits. The required mechanical properties of individual material phases are directly measured using nanoindentation with in-build scanning probe microscopy. Applicability of the proposed computational methodology is supported by the analysis of a unidirectional fibrous composite, representing the yarn, subjected to a macroscopically uniform strain.

Propagation law of impact elastic wave based on specific materials

Directory of Open Access Journals (Sweden)

Chunmin CHEN

2017-02-01

Full Text Available In order to explore the propagation law of the impact elastic wave on the platform, the experimental platform is built by using the specific isotropic materials and anisotropic materials. The glass cloth epoxy laminated plate is used for anisotropic material, and an organic glass plate is used for isotropic material. The PVDF sensors adhered on the specific materials are utilized to collect data, and the elastic wave propagation law of different thick plates and laminated plates under impact conditions is analyzed. The Experimental results show that in anisotropic material, transverse wave propagation speed along the fiber arrangement direction is the fastest, while longitudinal wave propagation speed is the slowest. The longitudinal wave propagation speed in anisotropic laminates is much slower than that in the laminated thick plates. In the test channel arranged along a particular angle away from the central region of the material, transverse wave propagation speed is larger. Based on the experimental results, this paper proposes a material combination mode which is advantageous to elastic wave propagation and diffusion in shock-isolating materials. It is proposed to design a composite material with high acoustic velocity by adding regularly arranged fibrous materials. The overall design of the barrier material is a layered structure and a certain number of 90°zigzag structure.

Elastic Properties and Enhanced Piezoelectric Response at Morphotropic Phase Boundaries

Directory of Open Access Journals (Sweden)

Francesco Cordero

2015-12-01

Full Text Available The search for improved piezoelectric materials is based on the morphotropic phase boundaries (MPB between ferroelectric phases with different crystal symmetry and available directions for the spontaneous polarization. Such regions of the composition x − T phase diagrams provide the conditions for minimal anisotropy with respect to the direction of the polarization, so that the polarization can easily rotate maintaining a substantial magnitude, while the near verticality of the TMPB(x boundary extends the temperature range of the resulting enhanced piezoelectricity. Another consequence of the quasi-isotropy of the free energy is a reduction of the domain walls energies, with consequent formation of domain structures down to nanoscale. Disentangling the extrinsic and intrinsic contributions to the piezoelectricity in such conditions requires a high level of sophistication from the techniques and analyses for studying the structural, ferroelectric and dielectric properties. The elastic characterization is extremely useful in clarifying the phenomenology and mechanisms related to ferroelectric MPBs. The relationship between dielectric, elastic and piezoelectric responses is introduced in terms of relaxation of defects with electric dipole and elastic quadrupole, and extended to the response near phase transitions in the framework of the Landau theory. An account is provided of the anelastic experiments, from torsional pendulum to Brillouin scattering, that provided new important information on ferroelectric MPBs, including PZT, PMN-PT, NBT-BT, BCTZ, and KNN-based systems.

Elastic Properties and Enhanced Piezoelectric Response at Morphotropic Phase Boundaries

Science.gov (United States)

Cordero, Francesco

2015-01-01

The search for improved piezoelectric materials is based on the morphotropic phase boundaries (MPB) between ferroelectric phases with different crystal symmetry and available directions for the spontaneous polarization. Such regions of the composition x−T phase diagrams provide the conditions for minimal anisotropy with respect to the direction of the polarization, so that the polarization can easily rotate maintaining a substantial magnitude, while the near verticality of the TMPBx boundary extends the temperature range of the resulting enhanced piezoelectricity. Another consequence of the quasi-isotropy of the free energy is a reduction of the domain walls energies, with consequent formation of domain structures down to nanoscale. Disentangling the extrinsic and intrinsic contributions to the piezoelectricity in such conditions requires a high level of sophistication from the techniques and analyses for studying the structural, ferroelectric and dielectric properties. The elastic characterization is extremely useful in clarifying the phenomenology and mechanisms related to ferroelectric MPBs. The relationship between dielectric, elastic and piezoelectric responses is introduced in terms of relaxation of defects with electric dipole and elastic quadrupole, and extended to the response near phase transitions in the framework of the Landau theory. An account is provided of the anelastic experiments, from torsional pendulum to Brillouin scattering, that provided new important information on ferroelectric MPBs, including PZT, PMN-PT, NBT-BT, BCTZ, and KNN-based systems. PMID:28793707

Prediction models of mechanical properties for pet-mortar composite in sodium sulphateaggressive mediums

Directory of Open Access Journals (Sweden)

Kazi Tani Nabil

2018-01-01

Full Text Available In this research, an investigation was carried out on the effect of sodium sulphate attack on the durability of composites produced with waste polyethylene terephthalate (PET. Experiments were accomplished on limestone sand and cement mortars where the blended Portland cement was partially replaced by various volume fractions of waste PET particles (6%, 12% and 17%. The test solutions used to supply the sulphate ions and cations were 5%sodium sulphate solution. Compressive strengths measured on specimens were used to assess the changes in the mechanical properties of PET-mortars exposed to sulphate attack at different ages, mainly the Young modulus of elasticity. Based on experimental compressive tests on PETMortar composite specimens and there densities, the evolution of Young modulus of elasticity has been analyzed in accordance with normative models given by (ACI-318 and (BS-8110 codes of practice. In addition, a comparative study has been carried out for corrosion resistance coefficients K of unmodified mortar to those modified with waste PET particles. It can be noticed that, for the composite immersed in a corrosive Na2SO4 solution, the corrosion resistance coefficients decrease with the increase of the immersion period. The corrosion sulphate resistance K based on Young modulus before and after immersion of PET-mortar composites is better than that of the control mortar. Therefore, for safety considerations of PET-mortar composites use, ACI 318 is recommended code for design and investigation works. Also, it can be concluded that adding waste PET by volume fractions (6%, 12% and 17% to blend Portland cement renders this cement more resistant to the sodium sulphate aggressive medium. Therefore, composites materials based waste PET aare often presented as the materials of the future because of their potential for innovation and the advantages they offer. In fact, using waste PET as cement substitutes reduces the energy consumption. These

Unraveling complex nonlinear elastic behaviors in rocks using dynamic acousto-elasticity

Science.gov (United States)

Riviere, J.; Guyer, R.; Renaud, G.; TenCate, J. A.; Johnson, P. A.

2012-12-01

In comparison with standard nonlinear ultrasonic methods like frequency mixing or resonance based measurements that allow one to extract average, bulk variations of modulus and attenuation versus strain level, dynamic acousto-elasticity (DAE) allows to obtain the elastic behavior over the entire dynamic cycle, detailing the full nonlinear behavior under tension and compression, including hysteresis and memory effects. This method consists of exciting a sample in Bulk-mode resonance at strains of 10-7 to 10-5 and simultaneously probing with a sequence of high frequency, low amplitude pulses. Time of flight and amplitudes of these pulses, respectively related to nonlinear elastic and dissipative parameters, can be plotted versus vibration strain level. Despite complex nonlinear signatures obtained for most rocks, it can be shown that for low strain amplitude (Pasqualini et al., JGR 2007), but not with the extreme detail of elasticity provided by DAE. Previous quasi-static measurements made in Berea sandstone (Claytor et al, GRL 2009), show that the hysteretic behavior disappears when the protocol is performed at a very low strain-rate (static limit). Therefore, future work will aim at linking quasi-static and dynamic observations, i.e. the frequency or strain-rate dependence, in order to understand underlying physical phenomena.

Elastic interaction of hydrogen atoms on graphene: A multiscale approach from first principles to continuum elasticity

Science.gov (United States)

Branicio, Paulo S.; Vastola, Guglielmo; Jhon, Mark H.; Sullivan, Michael B.; Shenoy, Vivek B.; Srolovitz, David J.

2016-10-01

The deformation of graphene due to the chemisorption of hydrogen atoms on its surface and the long-range elastic interaction between hydrogen atoms induced by these deformations are investigated using a multiscale approach based on first principles, empirical interactions, and continuum modeling. Focus is given to the intrinsic low-temperature structure and interactions. Therefore, all calculations are performed at T =0 , neglecting possible temperature or thermal fluctuation effects. Results from different methods agree well and consistently describe the local deformation of graphene on multiple length scales reaching 500 Å . The results indicate that the elastic interaction mediated by this deformation is significant and depends on the deformation of the graphene sheet both in and out of plane. Surprisingly, despite the isotropic elasticity of graphene, within the linear elastic regime, atoms elastically attract or repel each other depending on (i) the specific site they are chemisorbed; (ii) the relative position of the sites; (iii) and if they are on the same or on opposite surface sides. The interaction energy sign and power-law decay calculated from molecular statics agree well with theoretical predictions from linear elasticity theory, considering in-plane or out-of-plane deformations as a superposition or in a coupled nonlinear approach. Deviations on the exact power law between molecular statics and the linear elastic analysis are evidence of the importance of nonlinear effects on the elasticity of monolayer graphene. These results have implications for the understanding of the generation of clusters and regular formations of hydrogen and other chemisorbed atoms on graphene.

Diffraction stress analysis of thin films; investigating elastic grain interaction

International Nuclear Information System (INIS)

Kumar, A.

2005-12-01

This work is dedicated to the investigation of specimens exhibiting anisotropic microstructures (and thus macroscopic elastic anisotropy) and/or inhomogeneous microstructures, as met near surfaces and in textured materials. The following aspects are covered: (i) Analysis of specimens with direction-dependent (anisotropic) elastic grain-interaction. Elastic grain-interaction determines the distribution of stresses and strains over the (crystallographically) differently oriented grains of a mechanically stressed polycrystal and the mechanical and diffraction (X-ray) elastic constants (relating (diffraction) lattice strains to mechanical stresses). Grain interaction models that allow for anisotropic, direction-dependent grain interaction have been developed very recently. The notion 'direction-dependent' grain-interaction signifies that different grain-interaction constraints prevail along different directions in a specimen. Practical examples of direction-dependent grain interaction are the occurrence of surface anisotropy in thin films and the surface regions of bulk polycrystals and the occurrence of grain-shape (morphological) texture. In this work, for the first time, stress analyses of thin films have been performed on the basis of these newly developed grain-interaction models. It has also been demonstrated that the identification of the (dominant) source of direction-dependent grain interaction is possible. The results for the grain interaction have been discussed in the light of microstructural investigations of the specimens by microscopic techniques. (ii) Analysis of specimens with depth gradients: Diffraction stress analysis can be hindered if gradients of the stress state, the composition or the microstructure occur in the specimen under investigation, as the so-called information depth varies in the course of a traditional stress measurement: Ambiguous results are thus generally obtained. In this work, a strategy for stress measurements at fixed

Elastic properties of thin poly(vinyl alcohol)–cellulose nanocrystal membranes

International Nuclear Information System (INIS)

Pakzad, A; Yassar, R S; Simonsen, J

2012-01-01

In spite of extensive studies on the preparation and characterization of nanocomposite materials, the correlation of their properties at the nanoscale with those in bulk is a relatively unexplored area. This is of great importance, especially for materials with potential biomedical applications, where surface properties are as important in determining their applicability as bulk characteristics. In this study, the nanomechanical characteristics of thin poly(vinyl alcohol) (PVOH)–poly(acrylic acid) (PAA)–cellulose nanocrystal (CNC) membranes were studied using the nanoindentation module in an atomic force microscope (AFM) and the properties were compared with the macro-scale properties obtained by tensile tests. In general, the elastic properties measured by nanoindentation followed the same trend as macro-scale tensile tests except for the PVOH 85-PAA 0-CNC 15 sample. In comparison to the macro-scale elastic properties, the measured elastic moduli with AFM were higher. Macro-scale tensile test results indicated that, in the presence of PAA, incorporation of CNCs up to 20 wt% improved the elastic modulus of PVOH, but when no PAA was added, increasing the CNC content above 10 wt% resulted in their agglomeration and degradation in mechanical properties of PVOH. The discrepancy between macro-scale tensile tests and nanoindentation in the PVOH 85-PAA 0-CNC 15 sample was correlated to the high degree of inhomogeneity of CNC dispersion in the matrix. It was found that the composites reinforced with cellulose nanocrystals had smaller indentation imprints and the pile-up effect increased with the increase of cellulose nanocrystal content. (paper)

DFT calculation for elastic constants of orthorhombic structure within WIEN2K code: A new package (ortho-elastic)

International Nuclear Information System (INIS)

Reshak, Ali H.; Jamal, Morteza

2012-01-01

Highlights: ► A new package for calculating elastic constants of orthorhombic structure is released. ► The package called ortho-elastic. ► It is compatible with [FP-(L)APW+lo] method implemented in WIEN2k code. ► Several orthorhombic structure compounds were used to test the new package. ► Elastic constants calculated using this package show good agreement with experiment. - Abstract: A new package for calculating the elastic constants of orthorhombic structure is released. The package called ortho-elastic. The formalism of calculating the ortho-elastic constants is described in details. The package is compatible with the highly accurate all-electron full-potential (linearized) augmented plane-wave plus local orbital [FP-(L)APW+lo] method implemented in WIEN2k code. Several orthorhombic structure compounds were used to test the new package. We found that the calculated elastic constants using the new package show better agreement with the available experimental data than the previous theoretical results used different methods. In this package the second-order derivative E ″ (ε) of polynomial fit E=E(ε) of energy vs strains at zero strain (ε=0), used to calculate the orthorhombic elastic constants.

Implantable blood pressure sensor for analyzing elasticity in arteries

Science.gov (United States)

Franco-Ayala, Marco; Martínez-Piñón, Fernando; Reyes-Barranca, Alfredo; Sánchez de la Peña, Salvador; Álvarez-Chavez, José A.

2009-03-01

MEMS technology could be an option for the development of a pressure sensor which allows the monitoring of several electronic signals in humans. In this work, a comparison is made between the typical elasticity curves of several arteries in the human body and the elasticity obtained for MEMS silicon microstructures such as membranes and cantilevers employing Finite Element analysis tools. The purpose is to identify which types of microstructures are mechanically compatible with human arteries. The goal is to integrate a blood pressure sensor which can be implanted in proximity with an artery. The expected benefits for this type of sensor are mainly to reduce the problems associated with the use of bulk devices through the day and during several days. Such a sensor could give precise blood pressure readings in a continuous or periodic form, i.e. information that is especially important for some critical cases of hypertension patients.

Elastic/plastic analyses of advanced composites investigating the use of the compliant layer concept in reducing residual stresses resulting from processing

Science.gov (United States)

Arnold, Steven M.; Arya, Vinod K.; Melis, Matthew E.

1990-01-01

High residual stresses within intermetallic and metal matrix composite systems can develop upon cooling from the processing temperature to room temperature due to the coefficient of thermal expansion (CTE) mismatch between the fiber and matrix. As a result, within certain composite systems, radial, circumferential, and/or longitudinal cracks have been observed to form at the fiber-matrix interface. The compliant layer concept (insertion of a compensating interface material between the fiber and matrix) was proposed to reduce or eliminate the residual stress buildup during cooling and thus minimize cracking. The viability of the proposed compliant layer concept is investigated both elastically and elastoplastically. A detailed parametric study was conducted using a unit cell model consisting of three concentric cylinders to determine the required character (i.e., thickness and material properties) of the compliant layer as well as its applicability. The unknown compliant layer mechanical properties were expressed as ratios of the corresponding temperature dependent Ti-24Al-11Nb (a/o) matrix properties. The fiber properties taken were those corresponding to SCS-6 (SiC). Results indicate that the compliant layer can be used to reduce, if not eliminate, radial and circumferential residual stresses within the fiber and matrix and therefore also reduce or eliminate the radial cracking. However, with this decrease in in-plane stresses, one obtains an increase in longitudinal stress, thus potentially initiating longitudinal cracking. Guidelines are given for the selection of a specific compliant material, given a perfectly bonded system.

Temperature dependence of elastic properties of paratellurite

International Nuclear Information System (INIS)

Silvestrova, I.M.; Pisarevskii, Y.V.; Senyushenkov, P.A.; Krupny, A.I.

1987-01-01

New data are presented on the temperature dependence of the elastic wave velocities, elastic stiffness constants, and thermal expansion of paratellurite. It is shown that the external pressure appreciably influences the elastic properties of TeO 2 , especially the temperature dependence of the elastic modulus connected with the crystal soft mode. (author)

Bulk solitary waves in elastic solids

Science.gov (United States)

Samsonov, A. M.; Dreiden, G. V.; Semenova, I. V.; Shvartz, A. G.

2015-10-01

A short and object oriented conspectus of bulk solitary wave theory, numerical simulations and real experiments in condensed matter is given. Upon a brief description of the soliton history and development we focus on bulk solitary waves of strain, also known as waves of density and, sometimes, as elastic and/or acoustic solitons. We consider the problem of nonlinear bulk wave generation and detection in basic structural elements, rods, plates and shells, that are exhaustively studied and widely used in physics and engineering. However, it is mostly valid for linear elasticity, whereas dynamic nonlinear theory of these elements is still far from being completed. In order to show how the nonlinear waves can be used in various applications, we studied the solitary elastic wave propagation along lengthy wave guides, and remarkably small attenuation of elastic solitons was proven in physical experiments. Both theory and generation for strain soliton in a shell, however, remained unsolved problems until recently, and we consider in more details the nonlinear bulk wave propagation in a shell. We studied an axially symmetric deformation of an infinite nonlinearly elastic cylindrical shell without torsion. The problem for bulk longitudinal waves is shown to be reducible to the one equation, if a relation between transversal displacement and the longitudinal strain is found. It is found that both the 1+1D and even the 1+2D problems for long travelling waves in nonlinear solids can be reduced to the Weierstrass equation for elliptic functions, which provide the solitary wave solutions as appropriate limits. We show that the accuracy in the boundary conditions on free lateral surfaces is of crucial importance for solution, derive the only equation for longitudinal nonlinear strain wave and show, that the equation has, amongst others, a bidirectional solitary wave solution, which lead us to successful physical experiments. We observed first the compression solitary wave in the

Highly Elastic, Transparent, and Conductive 3D-Printed Ionic Composite Hydrogels

KAUST Repository

Odent, Jérémy

2017-07-17

Despite extensive progress to engineer hydrogels for a broad range of technologies, practical applications have remained elusive due to their (until recently) poor mechanical properties and lack of fabrication approaches, which constrain active structures to simple geometries. This study demonstrates a family of ionic composite hydrogels with excellent mechanical properties that can be rapidly 3D-printed at high resolution using commercial stereolithography technology. The new material design leverages the dynamic and reversible nature of ionic interactions present in the system with the reinforcement ability of nanoparticles. The composite hydrogels combine within a single platform tunable stiffness, toughness, extensibility, and resiliency behavior not reported previously in other engineered hydrogels. In addition to their excellent mechanical performance, the ionic composites exhibit fast gelling under near-UV exposure, remarkable conductivity, and fast osmotically driven actuation. The design of such ionic composites, which combine a range of tunable properties and can be readily 3D-printed into complex architectures, provides opportunities for a variety of practical applications such as artificial tissue, soft actuators, compliant conductors, and sensors for soft robotics.

Innovative energy absorbing devices based on composite tubes

Science.gov (United States)

Tiwari, Chandrashekhar

Analytical and experimental study of innovative load limiting and energy absorbing devices are presented here. The devices are based on composite tubes and can be categorized in to two groups based upon the energy absorbing mechanisms exhibited by them, namely: foam crushing and foam fracturing. The device based on foam crushing as the energy absorbing mechanism is composed of light weight elastic-plastic foam filling inside an angle ply composite tube. The tube is tailored to have a high Poisson’s ratio (>20). Upon being loaded the device experiences large transverse contraction resulting in rapid decrease in diameter. At a certain axial load the foam core begins to crush and energy is dissipated. This device is termed as crush tube device. The device based upon foam shear fracture as the energy absorbing mechanism involves an elastic-plastic core foam in annulus of two concentric extension-twist coupled composite tubes with opposite angles of fibers. The core foam is bonded to the inner and outer tube walls. Upon being loaded axially, the tubes twist in opposite directions and fracture the core foam in out of plane shear and thus dissipate the energy stored. The device is termed as sandwich core device (SCD). The devices exhibit variations in force-displacement characteristics with changes in design and material parameters, resulting in wide range of energy absorption capabilities. A flexible matrix composite system was selected, which was composed of high stiffness carbon fibers as reinforcements in relatively low stiffness polyurethane matrix, based upon large strain to failure capabilities and large beneficial elastic couplings. Linear and non-linear analytical models were developed encapsulating large deformation theory of the laminated composite shells (using non-linear strain energy formulation) to the fracture mechanics of core foam and elastic-plastic deformation theory of the foam filling. The non-linear model is capable of including material and

Numerical estimate of fracture parameters under elastic and elastic-plastic conditions

International Nuclear Information System (INIS)

Soba, Alejandro; Denis, Alicia C.

2003-01-01

The importance of the stress intensity factor K in the elastic fracture analysis is well known. In this work three methods are developed to estimate the parameter K I , corresponding to the normal loading mode, employing the finite elements method. The elastic-plastic condition is also analyzed, where the line integral J is the relevant parameter. Two cases of interest are studied: sample with a crack in its center and tubes with internal pressure. (author)

A new macroscopically anisotropic pressure dependent yield function for metal matrix composite based on strain gradient plasticity for the microstructure

DEFF Research Database (Denmark)

Azizi, Reza; Legarth, Brian Nyvang; Niordson, Christian Frithiof

2013-01-01

Metal matrix composites with long aligned elastic fibers are studied using an energetic rate independent strain gradient plasticity theory with an isotropic pressure independent yield function at the microscale. The material response is homogenized to obtain a conventional macroscopic model...... is investigated numerically using a unit cell model with periodic boundary conditions containing a single fiber deformed under generalized plane strain conditions. The homogenized response can be modeled by conventional plasticity with an anisotropic yield surface and a free energy depending on plastic strain...

Mastering ElasticSearch

CERN Document Server

Kuc, Rafal

2013-01-01

A practical tutorial that covers the difficult design, implementation, and management of search solutions.Mastering ElasticSearch is aimed at to intermediate users who want to extend their knowledge about ElasticSearch. The topics that are described in the book are detailed, but we assume that you already know the basics, like the query DSL or data indexing. Advanced users will also find this book useful, as the examples are getting deep into the internals where it is needed.

Work of adhesion measurements by a periodic cracking technique

International Nuclear Information System (INIS)

Davutoglu, A.; Aksay, I.A.

1981-01-01

In a recent study, Chow et al. introduced a technique for determining the energy associated with interfacial separation of a two-layer composite which consisted of a polymeric substrate and a brittle film overcoat. The technique is based on a model which assumes a perfectly elastic composite. In the present study, it s shown that as long as only the film component of the composite is brittle, the technique is also applicable to the composites where the substrates may display plastic deformation prior to adhesive failure of the film. Strain measurements, instead of load, eliminate the difficulties introduced by the plastic behavior of the substrate. Experimental work was performed on systems containing brittle amorphous selenium films on aluminum and Mylar substrates. These systems with selenium films were of interest due to their usage in photoreceptor technology

Design guidance for elastic followup

International Nuclear Information System (INIS)

Naugle, F.V.

1983-01-01

The basic mechanism of elastic followup is discussed in relation to piping design. It is shown how mechanistic insight gained from solutions for a two-bar problem can be used to identify dominant design parameters and to determine appropriate modifications where elastic followup is a potential problem. It is generally recognized that quantitative criteria are needed for elastic followup in the creep range where badly unbalanced lines can pose potential problems. Approaches for criteria development are discussed

Income Elasticity of Environmental Amenities

OpenAIRE

Daniel Miles; Andrés Pereyra; Máximo Rossi

2000-01-01

In this paper we are concerned with the estimation of income elasticities of environmental amenities. The novelty is the application of econometric methods that take into account the problem of measurement errors when estimating these elasticities, which are common in microeconomic data and are not usually considered in the applied literature related with this issue. Our aim is to discuss whether the measurement error has signi…cant e¤ects on the elasticities. Data from the Expenditure Budget...

Generalized linear elastic fracture mechanics: an application to a crack touching the bimaterial interface

Czech Academy of Sciences Publication Activity Database

Náhlík, Luboš; Šestáková, L.; Hutař, Pavel; Knésl, Zdeněk

2011-01-01

Roč. 452-453, - (2011), s. 445-448 ISSN 1013-9826 R&D Projects: GA AV ČR(CZ) KJB200410803; GA ČR GA101/09/1821 Institutional research plan: CEZ:AV0Z20410507 Keywords : generalized stress intensity factor * bimaterial interface * composite materials * strain energy density factor * fracture criterion * generalized linear elastic fracture mechanics Subject RIV: JL - Materials Fatigue, Friction Mechanics

On elastic waves in an thinly-layered laminated medium with stress couples under initial stress

Directory of Open Access Journals (Sweden)

P. Pal Roy

1988-01-01

Full Text Available The present work is concerned with a simple transformation rule in finding out the composite elastic coefficients of a thinly layered laminated medium whose bulk properties are strongly anisotropic with a microelastic bending rigidity. These elastic coefficients which were not known completely for a layered laminated structure, are obtained suitably in terms of initial stress components and Lame's constants λi, μi of initially isotropic solids. The explicit solutions of the dynamical equations for a prestressed thinly layered laminated medium under horizontal compression in a gravity field are derived. The results are discussed specifying the effects of hydrostatic, deviatoric and couple stresses upon the characteristic propagation velocities of shear and compression wave modes.

Simulation of Kinkband Formation in Fiber Composites

DEFF Research Database (Denmark)

Veluri, Badri; Jensen, Henrik Myhre

2010-01-01

subroutine in ABAQUS/Standard for analyzing the kinkband formation in the fiber composites under compressive loading within the framework of large deformation kinematics. This computational model analyses the effects of misalignment on elastic plastic deformation under plane strain conditions based...

In Situ elastic property sensors

International Nuclear Information System (INIS)

Olness, D.; Hirschfeld, T.; Kishiyama, K.; Steinhaus, R.

1987-01-01

Elasticity is an important property of many materials. Loss of elasticity can have serious consequences, such as when a gasket deteriorates and permits leakage of an expensive or hazardous material, or when a damping system begins to go awry. Loss of elasticity can also provide information related to an ancillary activity such as degradation of electrical insulation, loss of plasticizer in a plastic, or changes in permeability of a thin film. In fact, the mechanical properties of most organic compounds are altered when the compound degrades. Thus, a sensor for the mechanical properties can be used to monitor associated characteristics as well. A piezoelectric material in contact with an elastomer forms an oscillating system that can provide real-time elasticity monitoring. This combination constitutes a forced harmonic oscillator with damping provided by the elastomer. A ceramic oscillator with a total volume of a few mm 3 was used as an elasticity sensor. It was placed in intimate contact with an elastomer and then monitored remotely with a simple oscillator circuit and standard frequency counting electronics. Resonant frequency shifts and changes in Q value were observed corresponding to changes in ambient temperature and/or changes in pressure applied to the sample. Elastomer samples pretreated with ozone (to simulate aging) showed changes in Q value and frequency response, even though there were no visible changes in the elastic samples

Modern Nondestructive Test Methods for Army Ceramic Matrix Composites

National Research Council Canada - National Science Library

Strand, Douglas J

2008-01-01

.... Ceramic matrix composites (CMC) are potentially good high-temperature structural materials because of their low density, high elastic moduli, high strength, and for those with weak interfaces, surprisingly good damage tolerance...

High-energy elastic and quasi-elastic deuteron-nucleus scattering

International Nuclear Information System (INIS)

Tekou, Amouzou

1974-01-01

A study is made of deuteron-nucleus elastic and quasi-elastic scattering and the connection between the opaque nucleus model and the Glauber model is pointed out. The contributions to different cross-sections of the collisions in which the nucleus, excited by one of the nucleons of the deuteron, is brought back to the ground state by the other nucleon is analysed. Coherent deuteron disintegration is found to be highly improbable when the target nucleus is heavy and incoherent disintegration accounts for nearly all the deuteron disintegration. Thus a correct comparison between theoretical and experimental data on proton stripping must take the incoherent deuteron disintegration into consideration

Damage Assessment in a SiC-fiber reinforced Ceramic Matrix Composite

Directory of Open Access Journals (Sweden)

Konstantinos G. Dassios

2013-01-01

Full Text Available Assessment of the fracture behavior of a SiC-fbre-reinforced barium osumilite (BMAS ceramic matrix composite tested under static and cyclic tension conditions is reported herein. Notched specimens were used in order to limit material damage within a predefined gauge length. Imposition of successive unloading/reloading loops was found to result in an increase by 20% in material strength as compared to pure tension; the observed increase is attributed to energy dissipation from large-scale interfacial debonding phenomena that dominated the post-elastic tensile behaviour of the composite. Cyclic loading also helped establish the axial residual stress state of the fibres in the composite of tensile nature via a well-defined common intersection point of unloading-reloading cycles. A translation vector approach in the stress-strain plane was successful in establishing the residual stress-free properties of the composite and in reconciling the scatter noted in elastic properties of specimens with respect to theoretical expectations.