Evaluation of high-performance network technologies for ITER

International Nuclear Information System (INIS)

Zagar, K.; Hunt, S.; Kolaric, P.; Sabjan, R.; Zagar, A.; Dedic, J.

2010-01-01

For the fast feedback plasma controllers, ITER's Control, Data Access and Communication system (CODAC) will need to provide a mechanism for hard real-time communication between its distributed nodes. In particular, the ITER CODAC team identified four types of high-performance communication applications. Synchronous Databus Network (SDN) is to provide an ability to distribute parameters of plasma (estimated to about 5000 double-valued signals) across the system to allow for 1 ms control cycles. Event Distribution Network (EDN) and Time Communication Network (TCN) are to allow synchronization of node I/O operations to 10 ns. Finally, the Audio-Video Network (AVN) is to provide sufficient bandwidth for streaming of surveillance and diagnostics video at a high resolution (1024 x 1024) and frame rate (30 Hz). In this article, we present some combinations of common-off-the-shelf (COTS) technologies that allow the above requirements to be met. Also, we present the performances achieved in a practical (though small scale) technology demonstrator, which involved a real-time Linux operating running on National Instruments' PXI platform, UDP communication implemented directly atop the Ethernet network adapter, CISCO switches, Micro Research Finland's timing and event solution, and GigE audio-video streaming.

Evaluation of High-Performance Network Technologies for ITER

Energy Technology Data Exchange (ETDEWEB)

Zagar, K.; Kolaric, P.; Sabjan, R.; Zagar, A. [Cosylab d.d., Ljubljana (Slovenia); Hunt, S. [Alceli Hunt Beratung, Meisterschwanden (Switzerland)

2009-07-01

To facilitate fast feedback control of plasma, ITER's Control, Data Access and Communication system (CODAC) will need to provide a mechanism for hard real-time communication between its distributed nodes. In particular, four types of high-performance communication have been identified. Synchronous Databus Network (SDN) is to provide an ability to distribute parameters of plasma (estimated to about 5000 double-valued signals) across the system to allow for 1 ms control cycles. Event Distribution Network (EDN) and Time Communication Network (TCN) are to allow synchronization of node I/O operations to 10 ns. Finally, the Audio Video Network (AVN) is to provide sufficient bandwidth for streaming of surveillance and diagnostics video at a high resolution (1024*1024) and frame rate (30 Hz). In this article, we present some combinations of common off-the-shelf (COTS) technologies that allow the above requirements to be met. Also, we present the performances achieved in a practical (though small scale) technology demonstrator, which involved a real-time LINUS operating running on National Instruments' PXI platform, UDP communication implemented directly atop the Ethernet network adapter, CISCO switches, Micro Research Finland's timing and event solution, and GigE audio-video streaming. This document is composed of an abstract followed by the presentation transparencies. (authors)

Evaluation of high-performance network technologies for ITER

Energy Technology Data Exchange (ETDEWEB)

Zagar, K., E-mail: klemen.zagar@cosylab.co [Cosylab d.d., 1000 Ljubljana (Slovenia); Hunt, S. [Alceli Hunt Beratung, 5616 Meisterschwanden (Switzerland); Kolaric, P.; Sabjan, R.; Zagar, A.; Dedic, J. [Cosylab d.d., 1000 Ljubljana (Slovenia)

2010-07-15

For the fast feedback plasma controllers, ITER's Control, Data Access and Communication system (CODAC) will need to provide a mechanism for hard real-time communication between its distributed nodes. In particular, the ITER CODAC team identified four types of high-performance communication applications. Synchronous Databus Network (SDN) is to provide an ability to distribute parameters of plasma (estimated to about 5000 double-valued signals) across the system to allow for 1 ms control cycles. Event Distribution Network (EDN) and Time Communication Network (TCN) are to allow synchronization of node I/O operations to 10 ns. Finally, the Audio-Video Network (AVN) is to provide sufficient bandwidth for streaming of surveillance and diagnostics video at a high resolution (1024 x 1024) and frame rate (30 Hz). In this article, we present some combinations of common-off-the-shelf (COTS) technologies that allow the above requirements to be met. Also, we present the performances achieved in a practical (though small scale) technology demonstrator, which involved a real-time Linux operating running on National Instruments' PXI platform, UDP communication implemented directly atop the Ethernet network adapter, CISCO switches, Micro Research Finland's timing and event solution, and GigE audio-video streaming.

HIGH VOLTAGE ENVIRONMENTAL APPLICATIONS, INC.ELECTRON BEAM TECHNOLOGY - INNOVATIVE TECHNOLOGY EVALUATION REPORT

Science.gov (United States)

This report evaluates a high-voltage electron beam (E-beam) technology's ability to destroy volatile organic compounds (VOCs) and other contaminants present in liquid wastes. Specifically, this report discusses performance and economic data from a Superfund Innovative Technology...

Evaluating TCMS Train-to-Ground communication performances based on the LTE technology and discreet event simulations

DEFF Research Database (Denmark)

Bouaziz, Maha; Yan, Ying; Kassab, Mohamed

2018-01-01

is shared between the train and different passengers. The simulation is based on the discrete-events network simulator Riverbed Modeler. Next, second step focusses on a co-simulation testbed, to evaluate performances with real traffic based on Hardware-In-The-Loop and OpenAirInterface modules. Preliminary...... (Long Term Evolution) network as an alternative communication technology, instead of GSM-R (Global System for Mobile communications-Railway) because of some capacity and capability limits. First step, a pure simulation is used to evaluate the network load for a high-speed scenario, when the LTE network...... simulation and co-simulation results show that LTE provides good performance for the TCMS traffic exchange in terms of packet delay and data integrity...

Technology Evaluation Report: Non-destructive ...

Science.gov (United States)

Technology Evaluation Report HSRP is working to develop tools and information that will help detect the intentional introduction of chemical or biological contaminants in buildings or water systems, the containment of these contaminants, the decontamination of buildings and/or water systems, and the management of wastes generated from decontamination and cleanup operations. Evaluation of the performance of CBI Polymers’ DeconGelTM 1108, Environmental Alternatives, Inc.’s (EAI’s) Rad-Release II (RRII), Environmental Alternatives, Inc.’s SuperGel, and Intek Technologies’ LH-21. The objective of evaluating these technologies was to test their ability to remove radioactive cesium (Cs)-137 from the mixed building material coupons of brick with mortar, tile with grout, granite with mortar, all mortar and all grout coupons.

Dry Process Fuel Performance Evaluation

Energy Technology Data Exchange (ETDEWEB)

Yang, Myung Seung; Song, K. C.; Moon, J. S. and others

2005-04-15

The objective of the project is to establish the performance evaluation system of DUPIC fuel during the Phase II R and D. In order to fulfil this objectives, irradiation test of DUPIC fuel was carried out in HANARO using the non-instrumented and SPND-instrumented rig. Also, the analysis on the in-reactor behavior analysis of DUPIC fuel, out-pile test using simulated DUPIC fuel as well as performance and integrity assessment in a commercial reactor were performed during this Phase. The R and D results of the Phase II are summarized as follows : - Performance evaluation of DUPIC fuel via irradiation test in HANARO - Post irradiation examination of irradiated fuel and performance analysis - Development of DUPIC fuel performance code (modified ELESTRES) considering material properties of DUPIC fuel - Irradiation behavior and integrity assessment under the design power envelope of DUPIC fuel - Foundamental technology development of thermal/mechanical performance evaluation using ANSYS (FEM package)

Dry Process Fuel Performance Evaluation

International Nuclear Information System (INIS)

Yang, Myung Seung; Song, K. C.; Moon, J. S. and others

2005-04-01

The objective of the project is to establish the performance evaluation system of DUPIC fuel during the Phase II R and D. In order to fulfil this objectives, irradiation test of DUPIC fuel was carried out in HANARO using the non-instrumented and SPND-instrumented rig. Also, the analysis on the in-reactor behavior analysis of DUPIC fuel, out-pile test using simulated DUPIC fuel as well as performance and integrity assessment in a commercial reactor were performed during this Phase. The R and D results of the Phase II are summarized as follows : - Performance evaluation of DUPIC fuel via irradiation test in HANARO - Post irradiation examination of irradiated fuel and performance analysis - Development of DUPIC fuel performance code (modified ELESTRES) considering material properties of DUPIC fuel - Irradiation behavior and integrity assessment under the design power envelope of DUPIC fuel - Foundamental technology development of thermal/mechanical performance evaluation using ANSYS (FEM package)

Method for evaluating environmental performance of technologies by using the interindustry relations table; Sangyo renkanhyo wo mochiita gijutsu no kankyosei hyoka shuho

Energy Technology Data Exchange (ETDEWEB)

Hondo, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-01-30

This paper describes a proposal of a method for evaluating environmental performance of technologies by using the interindustry relations table, and the case studies thereof. This method is characterized in that it can evaluate two effects affecting the environment: structuring of capital facilities required in association with introduction of the technologies and the changes in social structures. As a parameter to compare the technologies considering these effects, a concept of life cycle limited emission amount was introduced. In the case studies, life cycle limited CO2 emission amounts from using seven kinds of technologies were calculated, and environmental performances of each technology were compared. The result indicated that introduction in Japan of coal, oil and LNG fired thermal power generation will increase CO2 emission amount from the whole society. Conversely, introduction of hydraulic, nuclear, photovoltaic, and wind power generation technologies will reduce the CO2 emission amount. It is pointed out particularly that hydraulic and nuclear power generation can minimize CO2 emission from structuring capital facilities, and is an excellent technology from a viewpoint of reducing CO2 emission from the society as a whole. 5 refs., 6 figs., 1 tab.

Cost and performance of innovative remediation technologies

International Nuclear Information System (INIS)

Cummings, J.B.; Kingscott, J.W.; Fiedler, L.D.

1995-01-01

The selection and use of more cost-effective remedies requires better access to data on the performance and cost of technologies used in the field. To make data more widely available, the US Environmental Protection Agency is working jointly with member agencies of the Federal Remediation Technologies Round table to publish case studies of full-scale remediation and demonstration projects. EPA, DoD, and DOE have published case studies of cleanup projects primarily consisting of bioremediation, soil vapor extraction, and thermal desorption. Within the limits of this initial data set, the paper evaluates technology performance and cost. In the analysis of cost factors, the paper shows the use of a standardized Work Breakdown Structure (WBS). Use of the WBS will be important in future reporting of completed projects to facilitate cost comparison. The paper notes the limits to normalization and thus cross-site comparison which can be achieved using the WBS. The paper identifies conclusions from initial efforts to compile cost and performance data, highlights the importance of such efforts to the overall remediation effort, and discusses future cost and performance documentation efforts

Environmental performance evaluation of Beijing's energy use planning

International Nuclear Information System (INIS)

Wang Lei; Xu Linyu; Song Huimin

2011-01-01

In line with rapid economic development, urban energy consumption is increasing rapidly, resulting in environmental problems. After considering several methods to evaluate the environmental performance of energy use, including: energy ecological footprint, input-output analysis, emergy-exergy analysis, and multi-criteria decision-making, an environmental performance evaluation model is proposed, which combines the analytical hierarchy process, fuzzy extent analysis, and membership degree analysis. In the model, 18 sub-indicators of environmental performance from energy use planning are classified into four categories: structure of energy use and industry, technology and efficiency of energy use, environmental impacts caused by energy use, and the socio-economic benefits of energy use. Membership degree analysis is applied to each indicator. Three energy use scenarios which are, respectively, environment-friendly, technology-led, and economic policy-led are evaluated. The results show that the technology-led energy use planning is best. The sustainable energy use policies are proposed from three aspects, including optimizing the energy use and industrial structure, encouraging development of energy-saving and air pollution control technologies, and enhancing legislation on energy use management. The policies are helpful to optimize the trade-offs between economic growth and environmental protection in Beijing. - Highlights: → Our paper establishes a system of indicators according to the structure of urban energy use planning. → We have created a comprehensive environmental performance evaluation model in the research. → The model and results can serve as an important basis for decision-making to guide local government.

An evaluation of supersonic STOVL technology

Science.gov (United States)

Kidwell, G. H., Jr.; Lampkin, B. A.

1983-01-01

The purpose of this paper is to document the status of supersonic STOVL aircraft technology. The major focus is the presentation of summaries of pertinent aspects of supersonic STOVL technology, such as justification for STOVL aircraft, current designs and their recognized areas of uncertainty, recent research programs, current activities, plans, etc. The remainder of the paper is an evaluation of the performance differential between a current supersonic STOVL design and three production (or near production) fighters, one of them the AV-8B. The results indicate that there is not a large range difference between a STOL aircraft and a STOVL aircraft, and that other aspects of performance, such as field performance or combat maneuverability, may more than make up for this decrement.

1992 update of US EPA's Superfund Innovative Technology Evaluation (SITE) Emerging Technology Program

International Nuclear Information System (INIS)

Lewis, N.M.; Barkley, N.P.; Williams, T.

1992-01-01

The Superfund Innovative Technology Evaluation (SITE) Emerging Technology Program (ETP) has financially supported further development of bench- and pilot-scale testing and evaluation of innovative technologies for use at hazardous waste sites for five years. The ETP was established under the Superfund Amendments and Reauthorization Act (SARA) of 1986. The ETP complies with the goal of the SITE Program to promote, accelerate and make commercially available the development of alternative/innovative treatment technologies for use at Superfund sites. Technologies are submitted to the ETP through yearly solicitations for Preproposals. Applicants are asked to submit a detailed project proposal and a cooperative agreement application that requires Developer/EPA cost sharing. EPA co-funds selected Developers for one to two years. Second-year funding requires documentation of significant progress during the first year. Facilities, equipment, data collection, performance and development are monitored throughout the project. The US Department of Energy (DOE) and the US Air Force (USAF) are participants in the ETP. DOE has co-funded ETP projects since 1990 and the USAF since 1991. A goal of the ETP is to move developed technologies to the field-demonstration stage. A developer may be considered for participation in the SITE Demonstration Program if performance in the ETP indicates the technology is field-ready for evaluation. Six technology categories: biological, chemical, materials handling, physical, solidification/stabilization and thermal, are presently in the ETP. Technologies of primary interest to EPA are those that can treat complex mixtures of hazardous organic and inorganic contaminants and provide improved solids handling and/or pretreatment. An account of the background and progress of the ETP's first five years is presented in this paper. Technologies currently in the ETP are noted, and developers and EPA Project Managers, are listed. 4 refs., 11 figs., 6 tabs

Development of in-pile test and evaluation technology

Energy Technology Data Exchange (ETDEWEB)

Kang, Yung Hwan; Park, Jong Man; Joo, Kee Nam; Park, Duk Keun; Park, Se Jin; Oh, Jong Myung; Kim, Tae Ryong; Park Jin Suk; Lee, Jae Han [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1994-08-01

To develop the in-pile test and evaluation technologies using KMRR, basic design of instrumented capsule and auxiliary system for material irradiation test and the related studies are performed. First, reactor and test hole characteristics are summarized, and conceptual design requirements of capsule to KMRR are reviewed. And fundamental principles and criteria for the instrumented capsule design are summarized. Basic design and analysis of instrumented capsule are performed, and design of capsule supporting system are also performed and structural integrity of the system is analyzed. Based on the prior studies, test mock-ups are designed and manufactured, and thermohydraulic and vibration tests are prepared. And, as in-pile test evaluation technologies, KMRR neutron dosimetry and mechanical tests related to material irradiation are investigated. 67 figs, 30 tabs, 41 refs. (Author).

EPA [Environmental Protection Agency] SITE [Superfund Innovative Technology Evaluation] program seeks technology proposals

International Nuclear Information System (INIS)

Anon.

1989-01-01

EPA will issue an RFP to initiate the SITE-005 solicitation for demonstration of technologies under the Superfund Innovative Technology Evaluation (SITE) Program. This portion of the SITE program offers a mechanism for conducting a joint technology demonstration between EPA and the private sector. The goal of the demonstration program is to provide an opportunity for developers to demonstrate the performance of their technologies on actual hazardous wastes at Superfund sites, and to provide accurate and reliable data on that performance. Technologies selected must be of commercial scale and provide solutions to problems encountered at Superfund Sites. Primary emphasis in the RFP is on technologies that address: treatment of mixed, low level radioactive wastes in soils and groundwater; treatment of soils and sludges contaminated with organics and/or inorganics, materials handling as a preliminary step to treatment or further processing, treatment trains designed to handle specific wastes, are in situ technologies, especially those processes providing alternatives to conventional groundwater pump and treat techniques

Methodologic Guide for Evaluating Clinical Performance and Effect of Artificial Intelligence Technology for Medical Diagnosis and Prediction.

Science.gov (United States)

Park, Seong Ho; Han, Kyunghwa

2018-03-01

The use of artificial intelligence in medicine is currently an issue of great interest, especially with regard to the diagnostic or predictive analysis of medical images. Adoption of an artificial intelligence tool in clinical practice requires careful confirmation of its clinical utility. Herein, the authors explain key methodology points involved in a clinical evaluation of artificial intelligence technology for use in medicine, especially high-dimensional or overparameterized diagnostic or predictive models in which artificial deep neural networks are used, mainly from the standpoints of clinical epidemiology and biostatistics. First, statistical methods for assessing the discrimination and calibration performances of a diagnostic or predictive model are summarized. Next, the effects of disease manifestation spectrum and disease prevalence on the performance results are explained, followed by a discussion of the difference between evaluating the performance with use of internal and external datasets, the importance of using an adequate external dataset obtained from a well-defined clinical cohort to avoid overestimating the clinical performance as a result of overfitting in high-dimensional or overparameterized classification model and spectrum bias, and the essentials for achieving a more robust clinical evaluation. Finally, the authors review the role of clinical trials and observational outcome studies for ultimate clinical verification of diagnostic or predictive artificial intelligence tools through patient outcomes, beyond performance metrics, and how to design such studies. © RSNA, 2018.

Evaluative conditioning of food technologies

DEFF Research Database (Denmark)

Loebnitz, Natascha; Grunert, Klaus G

2015-01-01

Consumer attitudes play an important role in the acceptance of new technologies. The success of food innovations depends on understanding how consumers form and change attitudes toward food technologies. Earlier post hoc explanations suggest that evaluative conditioning can change consumer...... attitudes toward food technologies. The present study tests how evaluative conditioning can affect consumer acceptance of new food technologies. Furthermore, authors investigate whether evaluative conditioning is resistant to extinction after a two-month period and whether the evaluative conditioning effect...... prevails in a product-related context. Within an evaluative conditioning paradigm including between-subjects control groups in addition to standard within-subjects control conditions, participants were presented with three food technologies (conventional, enzyme, and genetic technology) paired...

Evaluating New Technology.

Science.gov (United States)

Carniol, Paul J; Heffelfinger, Ryan N; Grunebaum, Lisa D

2018-05-01

There are multiple complex issues to consider when evaluating any new technology. First evaluate the efficacy of the device. Then considering your patient population decide whether this technology brings an added benefit to your patients. If it meets these 2 criteria, then proceed to the financial analysis of acquiring this technology. The complete financial analysis has several important components that include but are not limited to cost, value, alternatives, return on investment, and associated marketing expense. Copyright © 2018 Elsevier Inc. All rights reserved.

A novel hybrid MCDM model for performance evaluation of research and technology organizations based on BSC approach.

Science.gov (United States)

Varmazyar, Mohsen; Dehghanbaghi, Maryam; Afkhami, Mehdi

2016-10-01

Balanced Scorecard (BSC) is a strategic evaluation tool using both financial and non-financial indicators to determine the business performance of organizations or companies. In this paper, a new integrated approach based on the Balanced Scorecard (BSC) and multi-criteria decision making (MCDM) methods are proposed to evaluate the performance of research centers of research and technology organization (RTO) in Iran. Decision-Making Trial and Evaluation Laboratory (DEMATEL) are employed to reflect the interdependencies among BSC perspectives. Then, Analytic Network Process (ANP) is utilized to weight the indices influencing the considered problem. In the next step, we apply four MCDM methods including Additive Ratio Assessment (ARAS), Complex Proportional Assessment (COPRAS), Multi-Objective Optimization by Ratio Analysis (MOORA), and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) for ranking of alternatives. Finally, the utility interval technique is applied to combine the ranking results of MCDM methods. Weighted utility intervals are computed by constructing a correlation matrix between the ranking methods. A real case is presented to show the efficacy of the proposed approach. Copyright © 2016 Elsevier Ltd. All rights reserved.

Evaluation of long term performance measurements of PV modules with different technologies

OpenAIRE

Degner, T.; Ries, M.

2004-01-01

PV modules of six different technologies (m-Si, mc-Si, EFG, CIS, CdTe, a-Si) have been monitored concerning the performance under external conditions for a period of more than 2 years. In addition to the standard solar radiation measurements with pyranometer solar sensors with corresponding cell technology have been used to supplement the measurements. This allows in principle to consider spectral effects. The solar radiation measured with the sensor and the pyranometer is analysed on monthly...

Evaluating Technology Transfer and Diffusion.

Science.gov (United States)

Bozeman, Barry; And Others

1988-01-01

Four articles discuss the evaluation of technology transfer and diffusion: (1) "Technology Transfer at the U.S. National Laboratories: A Framework for Evaluation"; (2) "Application of Social Psychological and Evaluation Research: Lessons from Energy Information Programs"; (3) "Technology and Knowledge Transfer in Energy R and D Laboratories: An…

Human Performance Technology (HPT): An Examination of Definitions through Dependent and Independent Variables.

Science.gov (United States)

Irlbeck, Sonja A.

2002-01-01

Provides a chronological perspective of human performance technology (HPT) definitions and an evaluation of them in terms of independent and dependent variables. Discusses human competence and performance technology and compares the definitions with the goals that have been articulated for HPT. (Author/LRW)

Technology Performance Level Assessment Methodology.

Energy Technology Data Exchange (ETDEWEB)

Roberts, Jesse D.; Bull, Diana L; Malins, Robert Joseph; Costello, Ronan Patrick; Aurelien Babarit; Kim Nielsen; Claudio Bittencourt Ferreira; Ben Kennedy; Kathryn Dykes; Jochem Weber

2017-04-01

The technology performance level (TPL) assessments can be applied at all technology development stages and associated technology readiness levels (TRLs). Even, and particularly, at low TRLs the TPL assessment is very effective as it, holistically, considers a wide range of WEC attributes that determine the techno-economic performance potential of the WEC farm when fully developed for commercial operation. The TPL assessment also highlights potential showstoppers at the earliest possible stage of the WEC technology development. Hence, the TPL assessment identifies the technology independent “performance requirements.” In order to achieve a successful solution, the entirety of the performance requirements within the TPL must be considered because, in the end, all the stakeholder needs must be achieved. The basis for performing a TPL assessment comes from the information provided in a dedicated format, the Technical Submission Form (TSF). The TSF requests information from the WEC developer that is required to answer the questions posed in the TPL assessment document.

Effect of technological advances on cochlear implant performance in adults.

Science.gov (United States)

Lenarz, Minoo; Joseph, Gert; Sönmez, Hasibe; Büchner, Andreas; Lenarz, Thomas

2011-12-01

To evaluate the effect of technological advances in the past 20 years on the hearing performance of a large cohort of adult cochlear implant (CI) patients. Individual, retrospective, cohort study. According to technological developments in electrode design and speech-processing strategies, we defined five virtual intervals on the time scale between 1984 and 2008. A cohort of 1,005 postlingually deafened adults was selected for this study, and their hearing performance with a CI was evaluated retrospectively according to these five technological intervals. The test battery was composed of four standard German speech tests: Freiburger monosyllabic test, speech tracking test, Hochmair-Schulz-Moser (HSM) sentence test in quiet, and HSM sentence test in 10 dB noise. The direct comparison of the speech perception in postlingually deafened adults, who were implanted during different technological periods, reveals an obvious improvement in the speech perception in patients who benefited from the recent electrode designs and speech-processing strategies. The major influence of technological advances on CI performance seems to be on speech perception in noise. Better speech perception in noisy surroundings is strong proof for demonstrating the success rate of new electrode designs and speech-processing strategies. Standard (internationally comparable) speech tests in noise should become an obligatory part of the postoperative test battery for adult CI patients. Copyright © 2011 The American Laryngological, Rhinological, and Otological Society, Inc.

Performance of Improved Dairy Cattle Technologies Among Farmers ...

African Journals Online (AJOL)

User

This study evaluated the performance of different dairy cattle technologies ... common phenomenon in Nigeria, especially among the poor segment of the society ... considerable amounts (over 70%) of milk today (Olaloku and Debre, 1992). ..... cross-bred dairy cattle was reported to be 30 percent of total dairy animals in.

A Survey on Economic-driven Evaluations of Information Technology

NARCIS (Netherlands)

Mutschler, B.B.; Zarvic, N.; Reichert, M.U.

2007-01-01

The economic-driven evaluation of information technology (IT) has become an important instrument in the management of IT projects. Numerous approaches have been developed to quantify the costs of an IT investment and its assumed profit, to evaluate its impact on business process performance, and to

Assessment and evaluation of technologies for environmental restoration. Progress report

Energy Technology Data Exchange (ETDEWEB)

Uzochukwu, G. A. [North Carolina A and T State Univ., Greensboro, NC (United States)

2000-06-30

Nuclear and commercial non-nuclear technologies that have the potential of meeting the environmental restoration objectives of the Department of Energy are being evaluated. A detailed comparison of innovative technologies available will be performed to determine the safest and most economical technology for meeting these objectives. Information derived from this effort will be matched with the multi-objective of the environmental restoration effort to ensure that the best, most economical, and the safest technologies are used in decision making at USDOE-SRS. Technology-related variables will be developed and the resulting data formatted and computerized for multimedia systems. The multimedia system will be made available to technology developers and evaluators to ensure that the safest and most economical technologies are developed for use at SRS and other DOE sites.

Assessment and evaluation of technologies for environmental restoration. Progress report

International Nuclear Information System (INIS)

Uzochukwu, G. A.

2000-01-01

Nuclear and commercial non-nuclear technologies that have the potential of meeting the environmental restoration objectives of the Department of Energy are being evaluated. A detailed comparison of innovative technologies available will be performed to determine the safest and most economical technology for meeting these objectives. Information derived from this effort will be matched with the multi-objective of the environmental restoration effort to ensure that the best, most economical, and the safest technologies are used in decision making at USDOE-SRS. Technology-related variables will be developed and the resulting data formatted and computerized for multimedia systems. The multimedia system will be made available to technology developers and evaluators to ensure that the safest and most economical technologies are developed for use at SRS and other DOE sites.

Assessment and evaluation of technologies for environmental restoration. Progress report

International Nuclear Information System (INIS)

Uzochukwu, G.A.

1999-01-01

Nuclear and commercial non-nuclear technologies that have the potential of meeting the environmental restoration objectives of the Department of Energy are being evaluated. A detailed comparison of innovative technologies available will be performed to determine the safest and most economical technology for meeting these objectives. Information derived from this effort will be matched with the multi-objective of the environmental restoration effort to ensure that the best, most economical, and the safest technologies are used in decision making at USDOE-SRS. Technology-related variables will be developed and the resulting data formatted and computerized for multimedia systems. The multimedia system will be made available to technology developers and evaluators to ensure that the safest and most economical technologies are developed for use at SRS and other DOE sites

Technology Evaluation Report 17. Videoconferencing in Theatre and Performance Studies

Directory of Open Access Journals (Sweden)

Mark Childs

2003-04-01

Full Text Available Previous reports in this series have indicated the growing acceptance of video-conferencing in education delivery. The current report compares a series of video-conferencing methods in an activity requiring precision of expression and communication: theatre and performance studies. The Accessing and Networking with National and International Expertise (ANNIE project is a two-year project undertaken jointly by the University of Warwick and the University of Kent at Canterbury, running from March 2001 to March 2003. The project's aim is to enhance students' learning experience in theatre studies by enabling access to research-based teaching and to workshops led by practitioners of national and international standing. Various technologies have been used, particularly ISDN video-conferencing, computer-mediated conferencing, and the Internet. This report concludes that video-conferencing methods will gain acceptance in education, as academic schools themselves are able to operate commonly available technology the assistance of specialised service units.

76 FR 30696 - Technology Evaluation Process

Science.gov (United States)

2011-05-26

...-NOA-0039] Technology Evaluation Process AGENCY: Office of Energy Efficiency and Renewable Energy... (DOE) seeks comments and information related to a commercial buildings technology evaluation process... evaluation efforts. The goal of creating this standard process is to evaluate energy-saving technologies in a...

Advanced fuel technology and performance

International Nuclear Information System (INIS)

1985-10-01

The purpose of the Advisory Group Meeting on Advanced Fuel Technology and Performance was to review the experience of advanced fuel fabrication technology, its performance, peculiarities of the back-end of the nuclear fuel cycle with regard to all types of reactors and to outline the future trends. As a result of the meeting recommendations were made for the future conduct of work on advanced fuel technology and performance. A separate abstract was prepared for each of the 20 papers in this issue

Technological Capability and Firm Performance

Directory of Open Access Journals (Sweden)

Fernanda Maciel Reichert

2014-08-01

Full Text Available This research aims to investigate the relationship between investments in technological capability and economic performance in Brazilian firms. Based on economic development theory and on developed countries history, it is assumed that this relationship is positive. Through key indicators, 133 Brazilian firms have been analyzed. Given the economic circumstances of an emerging economy, which the majority of businesses are primarily based on low and medium-low-technology industries, it is not possible to affirm the existence of a positive relation between technological capability and firm performance. There are other elements that allow firms to achieve such results. Firms of lower technological intensity industries performed above average in the economic performance indicators, adversely, they invested below average in technological capability. These findings do not diminish the merit of firms’ and country’s success. They in fact confirm a historical tradition of a country that concentrates its efforts on basic industries.

Technology in Paralympic sport: performance enhancement or essential for performance?

Science.gov (United States)

Burkett, Brendan

2010-02-01

People with disabilities often depend on assistive devices to enable activities of daily living as well as to compete in sport. Technological developments in sport can be controversial. To review, identify and describe current technological developments in assistive devices used in the summer Paralympic Games; and to prepare for the London 2012 Games, the future challenges and the role of technology are debated. A systematic review of the peer-reviewed literature and personal observations of technological developments at the Athens (2004) and Beijing (2008) Paralympic Games was conducted. Standard assistive devices can inhibit the Paralympians' abilities to perform the strenuous activities of their sports. Although many Paralympic sports only require technology similar to their Olympic counterparts, several unique technological modifications have been made in prosthetic and wheelchair devices. Technology is essential for the Paralympic athlete, and the potential technological advantage for a Paralympian, when competing against an Olympian, is unclear. Technology must match the individual requirements of the athlete with the sport in order for Paralympians to safely maximise their performance. Within the 'performance enhancement or essential for performance?' debate, any potential increase in mechanical performance from an assistive device must be considered holistically with the compensatory consequences the disability creates. To avoid potential technology controversies at the 2012 London Olympic and Paralympic Games, the role of technology in sport must be clarified.

Development of technology performance specifications for volatile organic compounds

International Nuclear Information System (INIS)

Purdy, C.; Schutte, W.E.

1993-01-01

The Office of Technology Development (OTD) within the Office of Environmental Restoration and Waste Management of the Department of Energy has a mission to deliver needed and usable technologies to its customers. The primary customers are individuals and organizations performing environmental characterization and remediation, waste cleanup, and pollution prevention at DOE sites. DOE faces a monumental task in cleaning up the dozen or so major sites and hundreds of smaller sites that were or are used to produce the US nuclear weapons arsenal and to develop nuclear technologies for national defense and for peaceful purposes. Contaminants and waste materials include the radionuclides associated with nuclear weapons, such as plutonium and tritium, and more common pollutants and wastes of industrial activity such as chromium, chlorinated solvents, and polychlorinated biphenyls (PCBs). Quite frequently hazardous wastes regulated by the Environmental Protection Agency are co-mingled with radioactive wastes regulated by the Nuclear Regulatory Commission to yield a open-quotes mixed waste,close quotes which increases the cleanup challenges from several perspectives. To help OTD and its investigators meet DOE's cleanup goal, technology performance specifications are being implemented for research and development and DT ampersand E projects. Technology performance specifications or open-quotes performance goalsclose quotes describe, quantitatively where possible, the technology development needs being addressed. These specifications are used to establish milestones, evaluate the status of ongoing projects, and determine the success of completed projects

76 FR 37344 - Technology Evaluation Process

Science.gov (United States)

2011-06-27

...-NOA-0039] Technology Evaluation Process AGENCY: Office of Energy Efficiency and Renewable Energy... seeks comments and information related to a commercial buildings technology evaluation process. DOE is seeking to create a process for evaluating emerging and underutilized energy efficient technologies for...

Energetic and economic evaluations on hydrogen storage technologies

Energy Technology Data Exchange (ETDEWEB)

Arca, S.; Di Profio, P.; Germani, R. [Perugia Univ., Perugia (Italy). Centro di Eccellenza Materiali Innovativi Nanostrutturati, Dip. Chimica; Savelli, G.; Cotana, F.; Rossi, F.; Amantini, M. [Universita degli Studi di Perugia, Perugia (Italy). Dipartimento di Ingegneria Industriale, Sezione di Fisica Tecnica

2008-07-01

With the development of the hydrogen economy and fuel cell vehicles, a major technological issue has emerged regarding the storage and delivery of large amounts of hydrogen. Several hydrogen storage methodologies are available while other technologies are being developed aside from the classical compression and liquefaction of hydrogen. A novel technology is also in rapid process, which is based on clathrate hydrates of hydrogen. The features and performances of available storage systems were evaluated in an effort to determine the best technology throughout the hydrogen chain. For each of the storage solutions presented, the key parameters were compared. These key parameters included interaction energy between hydrogen and support; real and practical storage capacity; and specific energy consumption. The paper presented the study methods and discussed hydrogen storage technologies using compressed hydrogen; metal hydrides; liquefied hydrogen; carbon nanotubes; ammonia; and gas hydrates. Carbon dioxide emissions were also evaluated for each storage system analyzed. The paper also presented the worst scenario. It was concluded that a technology based on clathrate hydrates of hydrogen, while being far from optimized, was highly competitive with the classical approaches. 21 refs., 9 figs.

Impacts of FDI Renewable Energy Technology Spillover on China’s Energy Industry Performance

Directory of Open Access Journals (Sweden)

Weiwei Liu

2016-08-01

Full Text Available Environmental friendly renewable energy plays an indispensable role in energy industry development. Foreign direct investment (FDI in advanced renewable energy technology spillover is promising to improve technological capability and promote China’s energy industry performance growth. In this paper, the impacts of FDI renewable energy technology spillover on China’s energy industry performance are analyzed based on theoretical and empirical studies. Firstly, three hypotheses are proposed to illustrate the relationships between FDI renewable energy technology spillover and three energy industry performances including economic, environmental, and innovative performances. To verify the hypotheses, techniques including factor analysis and data envelopment analysis (DEA are employed to quantify the FDI renewable energy technology spillover and the energy industry performance of China, respectively. Furthermore, a panel data regression model is proposed to measure the impacts of FDI renewable energy technology spillover on China’s energy industry performance. Finally, energy industries of 30 different provinces in China based on the yearbook data from 2005 to 2011 are comparatively analyzed for evaluating the impacts through the empirical research. The results demonstrate that FDI renewable energy technology spillover has positive impacts on China’s energy industry performance. It can also be found that the technology spillover effects are more obvious in economic and technological developed regions. Finally, four suggestions are provided to enhance energy industry performance and promote renewable energy technology spillover in China.

ENVIRONMENTAL AND SUSTAINABLE TECHNOLOGY EVALUATION: BIOMASS CO-FIRING IN INDUSTRIAL BOILERS--UNIVERSITY OF IOWA

Science.gov (United States)

The U.S. EPA operates the Environmental and Sustainable Technology Evaluation (ESTE) program to facilitate the deployment of innovative technologies through performance verification and information dissemination. This ESTE project involved evaluation of co-firing common woody bio...

Irradiation test and performance evaluation of DUPIC fuel

International Nuclear Information System (INIS)

Yang, Myung Seung; Song, K. C.; Moon, J. S.

2002-05-01

The objective of the project is to establish the performance evaluation system of DUPIC fuel during the Phase II R and D. In order to fulfil this objectives, irradiation test of DUPIC fuel was carried out in HANARO using the non-instrumented and SPND-instrumented rig. Also, the analysis on the in-reactor behavior analysis of DUPIC fuel, out-pile test using simulated DUPIC fuel as well as performance and integrity assessment in a commercial reactor were performed during this Phase. The R and D results of the Phase II are summarized as follows : - Performance evaluation of DUPIC fuel via irradiation test in HANARO - Post irradiation examination of irradiated fuel and performance analysis - Development of DUPIC fuel performance code (modified ELESTRES) considering material properties of DUPIC fuel - Irradiation behavior and integrity assessment under the design power envelope of DUPIC fuel - Foundamental technology development of thermal/mechanical performance evaluation using ANSYS (FEM package)

Impact evaluation for University-Business Cooperation and Technology Transfer in higher education systems: cluster analysis

Directory of Open Access Journals (Sweden)

Tomoe Daniela Hamanaka Gusberti

2017-09-01

Full Text Available Abstract Higher education systems evolved in recent decades. Universities must not only provide society with capable professionals but also act in the market for technologies, knowledge, and ideas to promote technological development. This paper discusses the motivational performance evaluation system for technology transfer process, specifically the patterns’ evaluation of academic units considering micro-cultures and idiosyncrasies’ analysis, in the academic context of autonomy. Based on action research, the existing performance evaluation system was assessed, and multivariate cluster analysis was proposed and tested as a method to enable micro cultures’ identification and evaluation. The analysis proposed enabled a tool for reflexive discussion regarding the effectiveness of the institutional innovation system in academic units and Engineering Education, and its implications for social and technological development of industry and society enabled action proposals for improvement in the university’s technology transfer management process.

Guideline for Performing Systematic Approach to Evaluate and Qualify Legacy Documents that Support Advanced Reactor Technology Activity

Energy Technology Data Exchange (ETDEWEB)

Honma, George [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-10-01

The establishment of a systematic process for the evaluation of historic technology information for use in advanced reactor licensing is described. Efforts are underway to recover and preserve Experimental Breeder Reactor II and Fast Flux Test Facility historical data. These efforts have generally emphasized preserving information from data-acquisition systems and hard-copy reports and entering it into modern electronic formats suitable for data retrieval and examination. The guidance contained in this document has been developed to facilitate consistent and systematic evaluation processes relating to quality attributes of historic technical information (with focus on sodium-cooled fast reactor (SFR) technology) that will be used to eventually support licensing of advanced reactor designs. The historical information may include, but is not limited to, design documents for SFRs, research-and-development (R&D) data and associated documents, test plans and associated protocols, operations and test data, international research data, technical reports, and information associated with past U.S. Nuclear Regulatory Commission (NRC) reviews of SFR designs. The evaluation process is prescribed in terms of SFR technology, but the process can be used to evaluate historical information for any type of advanced reactor technology. An appendix provides a discussion of typical issues that should be considered when evaluating and qualifying historical information for advanced reactor technology fuel and source terms, based on current light water reactor (LWR) requirements and recent experience gained from Next Generation Nuclear Plant (NGNP).

Guideline for Performing Systematic Approach to Evaluate and Qualify Legacy Documents that Support Advanced Reactor Technology Activity

International Nuclear Information System (INIS)

Honma, George

2015-01-01

The establishment of a systematic process for the evaluation of historic technology information for use in advanced reactor licensing is described. Efforts are underway to recover and preserve Experimental Breeder Reactor II and Fast Flux Test Facility historical data. These efforts have generally emphasized preserving information from data-acquisition systems and hard-copy reports and entering it into modern electronic formats suitable for data retrieval and examination. The guidance contained in this document has been developed to facilitate consistent and systematic evaluation processes relating to quality attributes of historic technical information (with focus on sodium-cooled fast reactor (SFR) technology) that will be used to eventually support licensing of advanced reactor designs. The historical information may include, but is not limited to, design documents for SFRs, research-and-development (R&D) data and associated documents, test plans and associated protocols, operations and test data, international research data, technical reports, and information associated with past U.S. Nuclear Regulatory Commission (NRC) reviews of SFR designs. The evaluation process is prescribed in terms of SFR technology, but the process can be used to evaluate historical information for any type of advanced reactor technology. An appendix provides a discussion of typical issues that should be considered when evaluating and qualifying historical information for advanced reactor technology fuel and source terms, based on current light water reactor (LWR) requirements and recent experience gained from Next Generation Nuclear Plant (NGNP).

A Training Technology Evaluation Tool

National Research Council Canada - National Science Library

Livingston, Stephen C; Dyer, Jean L; Swinson, Diadra

2005-01-01

A Training Technology Evaluation Tool was developed to help procurers and developers of training technologies to make informed decisions and to improve the overall effectiveness of training technologies...

Evaluating supplier quality performance using analytical hierarchy process

Science.gov (United States)

Kalimuthu Rajoo, Shanmugam Sundram; Kasim, Maznah Mat; Ahmad, Nazihah

2013-09-01

This paper elaborates the importance of evaluating supplier quality performance to an organization. Supplier quality performance evaluation reflects the actual performance of the supplier exhibited at customer's end. It is critical in enabling the organization to determine the area of improvement and thereafter works with supplier to close the gaps. Success of the customer partly depends on supplier's quality performance. Key criteria as quality, cost, delivery, technology support and customer service are categorized as main factors in contributing to supplier's quality performance. 18 suppliers' who were manufacturing automotive application parts evaluated in year 2010 using weight point system. There were few suppliers with common rating which led to common ranking observed by few suppliers'. Analytical Hierarchy Process (AHP), a user friendly decision making tool for complex and multi criteria problems was used to evaluate the supplier's quality performance challenging the weight point system that was used for 18 suppliers'. The consistency ratio was checked for criteria and sub-criteria. Final results of AHP obtained with no overlap ratings, therefore yielded a better decision making methodology as compared to weight point rating system.

Using information technology to measure, monitor and report on environmental performance

Energy Technology Data Exchange (ETDEWEB)

Ford, G.

1999-07-01

This article provides an overview of the process of environmental performance evaluation (EPE), including a discussion of the rationale and context for EPE as a key component of environmental management and sustainability metrics for businesses around the world. New and emerging developments, such as environmental performance benchmarking and standardized reporting, are highlighted. The ISO 14000 model for EPE and its environmental performance indicators is described. The article then discusses the need for new technology, including the Internet, to meet these new demands, and examines the important role of information technology in creating an efficient and effective system for the EPE process. In this regard, issues such as scaleability, data identification, data collection, reporting, user interface, integration and data warehousing are explored, and examples of the application of information technology to address these issues are provided. The article concludes with a discussion of the need to use emerging information technology to integrate various key types of performance information, including environmental, according to the balanced scorecard model for integrated business sustainability metrics. It concludes that such technology should be used now, even in the absence of global standards for performance metrics, and in spite of the theoretical and practical challenges in doing so, in order to move toward the important goal of achieving comprehensive sustainability metrics.

Evaluating the Intellectual Capital of Technology Transfer and Learning Public Services

Directory of Open Access Journals (Sweden)

Michele Grimaldi

2013-03-01

Full Text Available Since the rise of the knowledge‐based economy, many worldwide companies have begun to deal with different frameworks to manage and evaluate the performance of intellectual capital, especially in the area of knowledge management services. This paper presents a novel conceptual model aiming to support management in evaluating and prioritizing their intellectual capital competitive core competences. Based on the analytic hierarchy process, the model analyses interdependences among intellectual capital elements and determines the impacts of core competences on organizational performance. To validate the model, it is empirically applied in the Technology Transfer Unit of the Italian national agency for new technologies, energy and economic development.

Simulation and rubrics: technology and grading student performance in nurse anesthesia education.

Science.gov (United States)

Overstreet, Maria; McCarver, Lewis; Shields, John; Patterson, Jordan

2015-06-01

The use of simulation technology has introduced a challenge for simulation nurse educators: evaluation of student performance. The subjectivity of student performance evaluation has been in need of improvement. It is imperative to provide clear and consistent information to the learner of expectations for their performance. Educators use objectives to define for the learner what the primary focus will be in the learning activities. Creation of rubrics to replace checklists to evaluate learner performance is a team task. Improved rubrics assist instructors in providing valuable, immediate, and postactivity feedback and consistency among instructors, and improved inter-rater reliability. Copyright © 2015 Elsevier Inc. All rights reserved.

Evaluating Instructor Technology Integration in Community and Technical Colleges: A Performance Evaluation Matrix

Science.gov (United States)

Del Favero, Marietta; Hinson, Janice M.

2007-01-01

The press for implementing technology based instructional delivery systems in community and technical colleges is well documented. Yet faculty face numerous challenges in integrating technology into instruction (AL-Bataineh & Brooks, 2003; Groves & Zemel, 2000; Khoury, 1997). Stimulating faculty ownership in technology, diffusion of technology use…

Technology-driven online marketing performance measurement: lessons from affiliate marketing

OpenAIRE

Bowie, David; Paraskevas, Alexandros; Mariussen, Anastasia

2014-01-01

Although the measurement of offline and online marketing is extensively researched, the literature on online performance measurement still has a number of limitations such as slow theory advancement and predominance of technology- and practitioner-driven measurement approaches. By focusing on the widely employed but under-researched affiliate marketing channel, this study addresses these limitations and evaluates the effectiveness of practitioner-led online performance assessment. The paper o...

How does technological regime affect performance of technology development projects?

NARCIS (Netherlands)

Song, Michael; Hooshangi, Soheil; Zhao, Y. Lisa; Halman, Johannes I.M.

2014-01-01

In this study, we examine how technological regime affects the performance of technology development projects (i.e., project quality, sales, and profit). Technological regime is defined as the set of attributes of a technological environment where the innovative activities of firms take place.

Characteristics and Performance of Existing Load Disaggregation Technologies

Energy Technology Data Exchange (ETDEWEB)

Mayhorn, Ebony T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Sullivan, Greg P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Butner, Ryan S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hao, He [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Baechler, Michael C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-04-10

Non-intrusive load monitoring (NILM) or non-intrusive appliance load monitoring (NIALM) is an analytic approach to disaggregate building loads based on a single metering point. This advanced load monitoring and disaggregation technique has the potential to provide an alternative solution to high-priced traditional sub-metering and enable innovative approaches for energy conservation, energy efficiency, and demand response. However, since the inception of the concept in the 1980’s, evaluations of these technologies have focused on reporting performance accuracy without investigating sources of inaccuracies or fully understanding and articulating the meaning of the metrics used to quantify performance. As a result, the market for, as well as, advances in these technologies have been slowly maturing.To improve the market for these NILM technologies, there has to be confidence that the deployment will lead to benefits. In reality, every end-user and application that this technology may enable does not require the highest levels of performance accuracy to produce benefits. Also, there are other important characteristics that need to be considered, which may affect the appeal of NILM products to certain market targets (i.e. residential and commercial building consumers) and the suitability for particular applications. These characteristics include the following: 1) ease of use, the level of expertise/bandwidth required to properly use the product; 2) ease of installation, the level of expertise required to install along with hardware needs that impact product cost; and 3) ability to inform decisions and actions, whether the energy outputs received by end-users (e.g. third party applications, residential users, building operators, etc.) empower decisions and actions to be taken at time frames required for certain applications. Therefore, stakeholders, researchers, and other interested parties should be kept abreast of the evolving capabilities, uses, and characteristics

End-User Evaluations of Semantic Web Technologies

Energy Technology Data Exchange (ETDEWEB)

McCool, Rob; Cowell, Andrew J.; Thurman, David A.

2005-11-07

Stanford University's Knowledge Systems Laboratory (KSL) is working in partnership with Battelle Memorial Institute and IBM Watson Research Center to develop a suite of technologies for information extraction, knowledge representation & reasoning, and human-information interaction, in unison entitled 'Knowledge Associates for Novel Intelligence' (KANI). We have developed an integrated analytic environment composed of a collection of analyst associates, software components that aid the user at different stages of the information analysis process. An important part of our participatory design process has been to ensure our technologies and designs are tightly integrate with the needs and requirements of our end users, To this end, we perform a sequence of evaluations towards the end of the development process that ensure the technologies are both functional and usable. This paper reports on that process.

Evaluating Internal Technological Capabilities in Energy Companies

Directory of Open Access Journals (Sweden)

Mingook Lee

2016-03-01

Full Text Available As global competition increases, technological capability must be evaluated objectively as one of the most important factors for predominance in technological competition and to ensure sustainable business excellence. Most existing capability evaluation models utilize either quantitative methods, such as patent analysis, or qualitative methods, such as expert panels. Accordingly, they may be in danger of reflecting only fragmentary aspects of technological capabilities, and produce inconsistent results when different models are used. To solve these problems, this paper proposes a comprehensive framework for evaluating technological capabilities in energy companies by considering the complex properties of technological knowledge. For this purpose, we first explored various factors affecting technological capabilities and divided the factors into three categories: individual, organizational, and technology competitiveness. Second, we identified appropriate evaluation items for each category to measure the technological capability. Finally, by using a hybrid approach of qualitative and quantitative methods, we developed an evaluation method for each item and suggested a method to combine the results. The proposed framework was then verified with an energy generation and supply company to investigate its practicality. As one of the earliest attempts to evaluate multi-faceted technological capabilities, the suggested model can support technology and strategic planning.

U.S. DOE FreedomCAR and Vehicle Technologies Advanced Technology Development Program for Lithium-Ion Batteries: Gen 2 Performance Evaluation Interim Report

Energy Technology Data Exchange (ETDEWEB)

Jon P. Christophersen; Chet Motloch; Ira D. Bloom; Vince Battaglia; Ganesan Nagasubramanian; Tien Q. Duong

2003-02-01

The Advanced Technology Development Program is currently evaluating the performance of the second generation of Lithium-ion cells (i.e., Gen 2 cells). The 18650-size Gen 2 cells consist of a baseline chemistry and one variant chemistry. These cells were distributed over a matrix consisting of three states-of-charge (SOC) (60, 80, and 100% SOC), four temperatures (25, 35, 45, and 55°C), and three life tests (calendar-, cycle-, and accelerated-life). The calendar-life cells are clamped at an opencircuit voltage corresponding to 60% SOC and undergo a once-per-day pulse profile. The cycle-life cells are continuously pulsed using a profile that is centered around 60% SOC. The accelerated-life cells are following the calendar-life test procedures, but using the cycle-life pulse profile. Life testing is interrupted every four weeks for reference performance tests (RPTs), which are used to quantify changes in capacity, resistance, and power. The RPTs consist of a C1/1 and C1/25 static capacity tests, a low-current hybrid pulse power characterization test, and electrochemical impedance spectroscopy at 60% SOC. Capacity-, power-, and electrochemical impedance spectroscopy-based performance results are reported.

Evaluation of the main parameters affecting seismic performance of ...

Indian Academy of Sciences (India)

The current study considers forty eight (48) 3-D RC building models to .... Acceptance criteria for members and performance level criteria for buildings are ..... Evaluation and Retrofit of Concrete Buildings, Applied Technology Council, Vol 1.

Evaluation of Activity Recognition Algorithms for Employee Performance Monitoring

OpenAIRE

Mehreen Mumtaz; Hafiz Adnan Habib

2012-01-01

Successful Human Resource Management plays a key role in success of any organization. Traditionally, human resource managers rely on various information technology solutions such as Payroll and Work Time Systems incorporating RFID and biometric technologies. This research evaluates activity recognition algorithms for employee performance monitoring. An activity recognition algorithm has been implemented that categorized the activity of employee into following in to classes: job activities and...

Evaluation of Aqua-Ammonia Chiller Technologies and Field Site Installation

Energy Technology Data Exchange (ETDEWEB)

Zaltash, Abdolreza [ORNL

2007-09-01

The Naval Facilities Engineering Service Center (NFESC) has sponsored Oak Ridge National Laboratory (ORNL) to review, select, and evaluate advanced, gas-fired, 5-ton, aqua-ammonia, chiller technologies. The selection criteria was that units have COP values of 0.67 or better at Air-conditioning and Refrigeration Institute (ARI) 95 F outdoor rating conditions, an active refrigerant flow control, and a variable-speed condenser fan. These features are expected to allow these units to operate at higher ambient temperatures (up to the maximum operating temperature of 110 F) with minimal degradation in performance. ORNL evaluated three potential manufacturers of advanced, gas-fired, 5-ton, aqua-ammonia chillers-Robur, Ambian, and Cooling Technologies. Unfortunately, Robur did not meet the COP requirements and Cooling Technologies could not deliver a unit to be tested at the U.S. Department of Energy (DOE)-ORNL environmental chamber testing facility for thermally activated heat pumps. This eliminated these two technologies from further consideration, leaving only the Ambian chillers for evaluation. Two Ambian chillers were evaluated at the DOE-ORNL test facility. Overall these chillers operated well over a wide range of ambient conditions with minimal degradation in performance due to several control strategies used such as a variable speed condenser fan, a modulating burner, and active refrigerant flow control. These Ambian pre-commercial units were selected for installation and field testing at three federal facilities. NFESC worked with ORNL to assist with the site selection for installation and evaluation of these chillers. Two sites (ORNL and Naval Surface Warfare Center [NSWC] Corona) had a single chiller unit installed; and at one site (Naval Amphibious Base [NAB] Little Creek), two 5-ton chillers linked together were installed to provide 10 tons of cooling. A chiller link controller developed under this project was evaluated in the field test at Little Creek.

Analytical Performance Evaluation of Different Switch Solutions

Directory of Open Access Journals (Sweden)

Francisco Sans

2013-01-01

Full Text Available The virtualization of the network access layer has opened new doors in how we perceive networks. With this virtualization of the network, it is possible to transform a regular PC with several network interface cards into a switch. PC-based switches are becoming an alternative to off-the-shelf switches, since they are cheaper. For this reason, it is important to evaluate the performance of PC-based switches. In this paper, we present a performance evaluation of two PC-based switches, using Open vSwitch and LiSA, and compare their performance with an off-the-shelf Cisco switch. The RTT, throughput, and fairness for UDP are measured for both Ethernet and Fast Ethernet technologies. From this research, we can conclude that the Cisco switch presents the best performance, and both PC-based switches have similar performance. Between Open vSwitch and LiSA, Open vSwitch represents a better choice since it has more features and is currently actively developed.

Mixed Waste Integrated Program interim evaluation report on thermal treatment technologies

International Nuclear Information System (INIS)

Gillins, R.L.; DeWitt, L.M.; Wollerman, A.L.

1993-02-01

The Mixed Waste Integrated Program (MWIP) is one of several US Department of Energy (DOE) integrated programs established to organize and coordinate throughout the DOE complex the development of technologies for treatment of specific waste categories. The goal of the MWIP is to develop and deploy appropriate technologies for -the treatment of DOE mixed low-level and alpha-contaminated wastes in order to bring all affected DOE installations and projects into compliance with environmental laws. Evaluation of treatment technologies by the MWIP will focus on meeting waste form performance requirements for disposal. Thermal treatment technologies were an early emphasis for the MWIP because thermal treatment is indicated (or mandated) for many of the hazardous constituents in DOE mixed waste and because these technologies have been widely investigated for these applications. An advisory group, the Thermal Treatment Working Group (TTWG), was formed during the program's infancy to assist the MWIP in evaluating and prioritizing thermal treatment technologies suitable for development. The results of the overall evaluation scoring indicate that the four highest-rated technologies were rotary kilns, slagging kilns, electric-arc furnaces, and plasma-arc furnaces. The four highest-rated technologies were all judged to be applicable on five of the six waste streams and are the only technologies in the evaluation with this distinction. Conclusions as to the superiority of one technology over others are not valid based on this preliminary study, although some general conclusions can be drawn

An exploratory study on the determinants of performance in regional industry technology development programs

Directory of Open Access Journals (Sweden)

Choo-Hui Park

2017-08-01

industrial technology development program performance are the characteristics of the technology development task rather than the internal R&D capability; moreover, the technical characteristics, complexity of the developed product market and participation of large corporations had significant effects on R&D capability. The R&D capacity of firms in internal R&D capacity had a significant effect only on the improvement of technology development ability. Therefore, R&D capacity, which is the main determinant of technology innovation, did not have a significant effect on the performance of short-term technology development tasks. Technological change, technological difficulty, competition between domestic and foreign competitors and the technological gap had positive effects on performance, excluding sales contributions. In addition, the complexity of the developed product market such as the diversification of demand, competitive product and sales distribution channels had positive influences on the performance of technology development programs, unlike dynamics and competitiveness. In this study, the authors cannot confirm the effect of collaborative research on the performance of the technology development programs, but they confirmed that collaborative research involving large corporations had a positive influence on performance. Research limitations/implications - The results of the analysis of the determinants of regional industrial technology development programs suggest some implications in the future evaluation of these regional industrial technology development programs. It is necessary to review the application qualification and merit, advance review of the business plans and confirmation, an examination of the research results and performance of the applicants and a review of the technology and market situation of the project. For this, the authors suggest that the written review from the relevant technical experts be submitted to the evaluation committees. Also, when

High performance APCS conceptual design and evaluation scoping study

International Nuclear Information System (INIS)

Soelberg, N.; Liekhus, K.; Chambers, A.; Anderson, G.

1998-02-01

This Air Pollution Control System (APCS) Conceptual Design and Evaluation study was conducted to evaluate a high-performance (APC) system for minimizing air emissions from mixed waste thermal treatment systems. Seven variations of high-performance APCS designs were conceptualized using several design objectives. One of the system designs was selected for detailed process simulation using ASPEN PLUS to determine material and energy balances and evaluate performance. Installed system capital costs were also estimated. Sensitivity studies were conducted to evaluate the incremental cost and benefit of added carbon adsorber beds for mercury control, specific catalytic reduction for NO x control, and offgas retention tanks for holding the offgas until sample analysis is conducted to verify that the offgas meets emission limits. Results show that the high-performance dry-wet APCS can easily meet all expected emission limits except for possibly mercury. The capability to achieve high levels of mercury control (potentially necessary for thermally treating some DOE mixed streams) could not be validated using current performance data for mercury control technologies. The engineering approach and ASPEN PLUS modeling tool developed and used in this study identified APC equipment and system performance, size, cost, and other issues that are not yet resolved. These issues need to be addressed in feasibility studies and conceptual designs for new facilities or for determining how to modify existing facilities to meet expected emission limits. The ASPEN PLUS process simulation with current and refined input assumptions and calculations can be used to provide system performance information for decision-making, identifying best options, estimating costs, reducing the potential for emission violations, providing information needed for waste flow analysis, incorporating new APCS technologies in existing designs, or performing facility design and permitting activities

Performance evaluation of thermophotovoltaic GaSb cell technology in high temperature waste heat

Science.gov (United States)

Utlu, Z.; Önal, B. S.

2018-02-01

In this study, waste heat was evaluated and examined by means of thermophotovoltaic systems with the application of energy production potential GaSb cells. The aim of our study is to examine GaSb cell technology at high temperature waste heat. The evaluation of the waste heat to be used in the system is designed to be used in the electricity, industry and iron and steel industry. Our work is research. Graphic analysis is done with Matlab program. The high temperature waste heat graphs applied on the GaSb cell are in the results section. Our study aims to provide a source for future studies.

Evaluation of the cleaner technology programme

DEFF Research Database (Denmark)

Andersen, Mikael Skou; Jørgensen, Ulrik

The report presents an independent evaluation of the Danish development programme for cleaner technology 1986-1989 and of the Action Plan for Cleaner Technology 1990-1992. The evaluation focuses on the results of technology development and implementation projects, on an examination...... of the dissemination of cleaner technology solutions achieved in six industrial branches, and on the overall programme and its effects, in particular environmental impacts, but also results in the form of employment, environmental export, strenghtening of Danish know-how etc....

ENVIRONMENTAL AND SUSTAINABLE TECHNOLOGY EVALUATION: BIOMASS CO-FIRING IN INDUSTRIAL BOILERS--MINNESOTA POWER'S RAPIDS ENERGY CENTER

Science.gov (United States)

The U.S. EPA operates the Environmental and Sustainable Technology Evaluation (ESTE) program to facilitate the deployment of innovative technologies through performance verification and information dissemination. This ESTE project involved evaluation of co-firing common woody bio...

Establishment of a Quantitative Medical Technology Evaluation System and Indicators within Medical Institutions.

Science.gov (United States)

Wu, Suo-Wei; Chen, Tong; Pan, Qi; Wei, Liang-Yu; Wang, Qin; Li, Chao; Song, Jing-Chen; Luo, Ji

2018-06-05

The development and application of medical technologies reflect the medical quality and clinical capacity of a hospital. It is also an effective approach in upgrading medical service and core competitiveness among medical institutions. This study aimed to build a quantitative medical technology evaluation system through questionnaire survey within medical institutions to perform an assessment to medical technologies more objectively and accurately, and promote the management of medical quality technologies and ensure the medical safety of various operations among the hospitals. A two-leveled quantitative medical technology evaluation system was built through a two-round questionnaire survey of chosen experts. The Delphi method was applied in identifying the structure of evaluation system and indicators. The judgment of the experts on the indicators was adopted in building the matrix so that the weight coefficient and maximum eigenvalue (λ max), consistency index (CI), and random consistency ratio (CR) could be obtained and collected. The results were verified through consistency tests, and the index weight coefficient of each indicator was conducted and calculated through analytical hierarchy process. Twenty-six experts of different medical fields were involved in the questionnaire survey, 25 of whom successfully responded to the two-round research. Altogether, 4 primary indicators (safety, effectiveness, innovativeness, and benefits), as well as 13 secondary indicators, were included in the evaluation system. The matrix is built to conduct the λ max, CI, and CR of each expert in the survey, and the index weight coefficients of primary indicators were 0.33, 0.28, 0.27, and 0.12, respectively, and the index weight coefficients of secondary indicators were conducted and calculated accordingly. As the two-round questionnaire survey of experts and statistical analysis were performed and credibility of the results was verified through consistency evaluation test, the

Irradiation and performance evaluation of DUPIC fuel

International Nuclear Information System (INIS)

Bae, Ki Kwang; Yang, M. S.; Song, K. C.

2000-05-01

The objectives of the project is to establish the performance evaluation system for the experimental verification of DUPIC fuel. The scope and content for successful accomplishment of the phase 1 objectives is established as follows : irradiation test of DUPIC fuel at HANARO using a noninstrument capsule, study on the characteristics of DUPIC pellets, development of the analysis technology on the thermal behaviour of DUPIC fuel, basic design of a instrument capsule. The R and D results of the phase 1 are summarized as follows : - Performance analysis technology development of DUPIC fuel by model development for DUPIC fuel, review on the extendability of code(FEMAXI-IV, FRAPCON-3, ELESTRESS). - Study on physical properties of DUPIC fuel by design and fabrication of the equipment for measuring the thermal property. - HANARO irradiation test of simulated DUPIC fuel by the noninstrument capsule development. - PIE and result analysis

Irradiation and performance evaluation of DUPIC fuel

Energy Technology Data Exchange (ETDEWEB)

Bae, Ki Kwang; Yang, M S; Song, K C [and others

2000-05-01

The objectives of the project is to establish the performance evaluation system for the experimental verification of DUPIC fuel. The scope and content for successful accomplishment of the phase 1 objectives is established as follows : irradiation test of DUPIC fuel at HANARO using a noninstrument capsule, study on the characteristics of DUPIC pellets, development of the analysis technology on the thermal behaviour of DUPIC fuel, basic design of a instrument capsule. The R and D results of the phase 1 are summarized as follows : - Performance analysis technology development of DUPIC fuel by model development for DUPIC fuel, review on the extendability of code(FEMAXI-IV, FRAPCON-3, ELESTRESS). - Study on physical properties of DUPIC fuel by design and fabrication of the equipment for measuring the thermal property. - HANARO irradiation test of simulated DUPIC fuel by the noninstrument capsule development. - PIE and result analysis.

GENERAL ENVIRONMENTAL CORPORATION; CURE ELECTROCOAGULATION TECHNOLOGY: INNOVATIVE TECHNOLOGY EVALUATION REPORT

Science.gov (United States)

The CURE electrocoagulation technology was demonstrated under the Superfund Innovative Technology Evaluation (SITE) program at the U.S. Department of Energy (DOE) Rocky Flats Environmental Technology Site (RFETS), where water from the solar evaporation ponds (SEPs) was contaminat...

Evaluation of alternative nonflame technologies for destruction of hazardous organic waste

International Nuclear Information System (INIS)

Schwinkendorf, W.E.; Musgrave, B.C.; Drake, R.N.

1997-04-01

The US Department of Energy's Mixed Waste Focus Area (MWFA) commissioned an evaluation of mixed waste treatment technologies that are alternatives to incineration for destruction of hazardous organic wastes. The purpose of this effort is to evaluate technologies that are alternatives to open-flame, free-oxygen combustion (as exemplified by incinerators), and recommend to the Waste Type Managers and the MWFA which technologies should be considered for further development. Alternative technologies were defined as those that have the potential to: destroy organic material without use of open-flame reactions with free gas-phase oxygen as the reaction mechanism; reduce the offgas volume and associated contaminants (metals, radionuclides, and particulates) emitted under normal operating conditions; eliminate or reduce the production of dioxins and furans; and reduce the potential for excursions in the process that can lead to accidental release of harmful levels of chemical or radioactive materials. Twenty-three technologies were identified that have the potential for meeting these requirements. These technologies were rated against the categories of performance, readiness for deployment, and environment safety, and health. The top ten technologies that resulted from this evaluation are Steam Reforming, Electron Beam, UV Photo-Oxidation, Ultrasonics, Eco Logic reduction process, Supercritical Water oxidation, Cerium Mediated Electrochemical Oxidation, DETOX SM , Direct Chemical Oxidation (peroxydisulfate), and Neutralization/Hydrolysis

Evaluating supplier quality performance using fuzzy analytical hierarchy process

Science.gov (United States)

Ahmad, Nazihah; Kasim, Maznah Mat; Rajoo, Shanmugam Sundram Kalimuthu

2014-12-01

Evaluating supplier quality performance is vital in ensuring continuous supply chain improvement, reducing the operational costs and risks towards meeting customer's expectation. This paper aims to illustrate an application of Fuzzy Analytical Hierarchy Process to prioritize the evaluation criteria in a context of automotive manufacturing in Malaysia. Five main criteria were identified which were quality, cost, delivery, customer serviceand technology support. These criteria had been arranged into hierarchical structure and evaluated by an expert. The relative importance of each criteria was determined by using linguistic variables which were represented as triangular fuzzy numbers. The Center of Gravity defuzzification method was used to convert the fuzzy evaluations into their corresponding crisps values. Such fuzzy evaluation can be used as a systematic tool to overcome the uncertainty evaluation of suppliers' performance which usually associated with human being subjective judgments.

EVALUATION OF SOLIDIFICATION/STABILIZATION AS A BEST DEMONSTRATED AVAILABLE TECHNOLOGY FOR CONTAMINATED SOILS

Science.gov (United States)

This project involved the evaluation of solidification/stabilization technology as a BDAT for contaminated soil. Three binding agents were used on four different synthetically contaminated soils. Performance evaluation data included unconfined compressive strength (UCS) and the T...

Formal Implementation of a Performance Evaluation Model for the Face Recognition System

Directory of Open Access Journals (Sweden)

Yong-Nyuo Shin

2008-01-01

Full Text Available Due to usability features, practical applications, and its lack of intrusiveness, face recognition technology, based on information, derived from individuals' facial features, has been attracting considerable attention recently. Reported recognition rates of commercialized face recognition systems cannot be admitted as official recognition rates, as they are based on assumptions that are beneficial to the specific system and face database. Therefore, performance evaluation methods and tools are necessary to objectively measure the accuracy and performance of any face recognition system. In this paper, we propose and formalize a performance evaluation model for the biometric recognition system, implementing an evaluation tool for face recognition systems based on the proposed model. Furthermore, we performed evaluations objectively by providing guidelines for the design and implementation of a performance evaluation system, formalizing the performance test process.

Study on the evaluation of decontamination and decommissioning technologies and their demands in Korea

Energy Technology Data Exchange (ETDEWEB)

Oh, Won Zin; Lee, K. W.; Jung, C. H.; Choi, W. K.; Won, H. J.; Kim, G. N.; Jung, K. J.; Chung, U. S.; Lee, D. G.; Kim, C. J.; Kim, S. H.; Chung, J. M.; Kwon, S. O. [Korea Atomic Energy Research Institute, Taejeon (Korea)

2001-03-01

D and D market demand, the current status of the technology, technology items applicable to the domestic market and the future prospect of technologies not self-developed in Korea were evaluated. In the evaluation of D and D market demand and the current status of the technology, 1) the market demand was investigated on the D and D objects such as the research reactors, the nuclear power plants and the nuclear fuel cycle development facilities from 2001 to 2010, and 2) the technology demand for decommissioning of the nuclear power plants from 2001 to 2030 were investigated. In the evaluation of the technology items applicable to the domestic market, 1) the analysis of the technologies derived from the technology requirements on D and D objects and their related similar technologies was performed, and 2) the technology items applicable to the domestic market were derived from the evaluation of the suitability on the domestic technology requirements. The promising technologies applicable to the domestic market were derived from the integrated evaluation of the technological factors(innovation, internationally competitive power and the difficulty of the technology development), economical factors (domestic demand and substitution effect of foreign currency) and domestically applicable factors (applicability on the industry and a ripple effect). The background of the technology development such as business applicability and the technology demonstration effect through the integrated management of the decommissioning of TRIGA reactor and the uranium conversion facility was also analyzed. 10 refs., 9 figs., 28 tabs. (Author)

Solar array technology evaluation program for SEPS (Solar Electrical Propulsion Stage)

Science.gov (United States)

1974-01-01

An evaluation of the technology and the development of a preliminary design for a 25 kilowatt solar array system for solar electric propulsion are discussed. The solar array has a power to weight ratio of 65 watts per kilogram. The solar array system is composed of two wings. Each wing consists of a solar array blanket, a blanket launch storage container, an extension/retraction mast assembly, a blanket tensioning system, an array electrical harness, and hardware for supporting the system for launch and in the operating position. The technology evaluation was performed to assess the applicable solar array state-of-the-art and to define supporting research necessary to achieve technology readiness for meeting the solar electric propulsion system solar array design requirements.

Practice-centred evaluation and the privileging of care in health information technology evaluation.

Science.gov (United States)

Darking, Mary; Anson, Rachel; Bravo, Ferdinand; Davis, Julie; Flowers, Steve; Gillingham, Emma; Goldberg, Lawrence; Helliwell, Paul; Henwood, Flis; Hudson, Claire; Latimer, Simon; Lowes, Paul; Stirling, Ian

2014-06-05

Our contribution, drawn from our experience of the case study provided, is a protocol for practice-centred, participative evaluation of technology in the clinical setting that privileges care. In this context 'practice-centred' evaluation acts as a scalable, coordinating framework for evaluation that recognises health information technology supported care as an achievement that is contingent and ongoing. We argue that if complex programmes of technology-enabled service innovation are understood in terms of their contribution to patient care and supported by participative, capability-building evaluation methodologies, conditions are created for practitioners and patients to realise the potential of technologies and make substantive contributions to the evidence base underpinning health innovation programmes. Electronic Patient Records (EPRs) and telemedicine are positioned by policymakers as health information technologies that are integral to achieving improved clinical outcomes and efficiency savings. However, evaluating the extent to which these aims are met poses distinct evaluation challenges, particularly where clinical and cost outcomes form the sole focus of evaluation design. We propose that a practice-centred approach to evaluation - in which those whose day-to-day care practice is altered (or not) by the introduction of new technologies are placed at the centre of evaluation efforts - can complement and in some instances offer advantages over, outcome-centric evaluation models. We carried out a regional programme of innovation in renal services where a participative approach was taken to the introduction of new technologies, including: a regional EPR system and a system to support video clinics. An 'action learning' approach was taken to procurement, pre-implementation planning, implementation, ongoing development and evaluation. Participants included clinicians, technology specialists, patients and external academic researchers. Whilst undergoing these

Evaluation of National School for Professional Technology Education in Mexico

OpenAIRE

Lopez-Acevedo, Gladys

2005-01-01

The National School for Professional Technology Education (CONALEP) is Mexico's largest and oldest technical education system. CONALEP serves low-income students at the upper-secondary school level in Mexico. The labor market performance of CONALEP graduates has been evaluated four times in the past. These evaluations have yielded encouraging results, showing that CONALEP's graduates find jobs faster and earn higher wages than similar "control" groups. In contrast, using non-experimental meth...

Sustainability evaluation of water supply technologies

DEFF Research Database (Denmark)

Godskesen, Berit

Sustainability evaluation of water supply systems is important to include in the decision making process when planning new technologies or resources for water supply. In Denmark the motivations may be many and different for changing technology, but since water supply is based on groundwater...... the main driver is the limitations of the available resource from the groundwater bodies. The environmental impact of products and systems can be evaluated by life-cycle assessment (LCA) which is a comprehensive and dominant decision support tool capable of evaluating a water system from the cradle......-criteria decision analysis method was used to develop a decision support system and applied to the study. In this thesis a standard LCA of the drinking water supply technology of today (base case) and 4 alternative cases for water supply technologies is conducted. The standard LCA points at the case rain...

A review of performance standards to monitor, evaluate and assess the impact of technology transfer offices

Directory of Open Access Journals (Sweden)

Sibongile Gumbi

2010-07-01

Full Text Available The conversion of scientific discoveries to new products and processes and their launch onto the market can be a lengthy process. Similarly, it takes many years before the impact of scientific research on society and the economy is realised and a further length of time before its performance can be measured. Higher education and research institutions, and their governments, often make significant investments into intellectual property management and technology transfer activities through legislative and policy development, human resource development, financial allocation and infrastructure improvement. Since returns on such investments are not immediately apparent, it is important to establish a means by which the impact of their efforts can be determined. In this paper, I examined the measures and indicators that could be developed by institutions and their stakeholders in order to monitor, evaluate and determine the impact of research output and outcomes on the market.

Evaluation of alternative nonflame technologies for destruction of hazardous organic waste

Energy Technology Data Exchange (ETDEWEB)

Schwinkendorf, W.E. [Lockheed Idaho Technologies Co., Idaho Falls, ID (United States); Musgrave, B.C. [BC Musgrave, Inc. (United States); Drake, R.N. [Drake Engineering, Inc. (United States)

1997-04-01

The US Department of Energy`s Mixed Waste Focus Area (MWFA) commissioned an evaluation of mixed waste treatment technologies that are alternatives to incineration for destruction of hazardous organic wastes. The purpose of this effort is to evaluate technologies that are alternatives to open-flame, free-oxygen combustion (as exemplified by incinerators), and recommend to the Waste Type Managers and the MWFA which technologies should be considered for further development. Alternative technologies were defined as those that have the potential to: destroy organic material without use of open-flame reactions with free gas-phase oxygen as the reaction mechanism; reduce the offgas volume and associated contaminants (metals, radionuclides, and particulates) emitted under normal operating conditions; eliminate or reduce the production of dioxins and furans; and reduce the potential for excursions in the process that can lead to accidental release of harmful levels of chemical or radioactive materials. Twenty-three technologies were identified that have the potential for meeting these requirements. These technologies were rated against the categories of performance, readiness for deployment, and environment safety, and health. The top ten technologies that resulted from this evaluation are Steam Reforming, Electron Beam, UV Photo-Oxidation, Ultrasonics, Eco Logic reduction process, Supercritical Water oxidation, Cerium Mediated Electrochemical Oxidation, DETOX{sup SM}, Direct Chemical Oxidation (peroxydisulfate), and Neutralization/Hydrolysis.

A Process For Performance Evaluation Of Real-Time Systems

Directory of Open Access Journals (Sweden)

Andrew J. Kornecki

2003-12-01

Full Text Available Real-time developers and engineers must not only meet the system functional requirements, but also the stringent timing requirements. One of the critical decisions leading to meeting these timing requirements is the selection of an operating system under which the software will be developed and run. Although there is ample documentation on real-time systems performance and evaluation, little can be found that combines such information into an efficient process for use by developers. As the software industry moves towards clearly defined processes, creation of appropriate guidelines describing a process for performance evaluation of real-time system would greatly benefit real-time developers. This technology transition research focuses on developing such a process. PROPERT (PROcess for Performance Evaluation of Real Time systems - the process described in this paper - is based upon established techniques for evaluating real-time systems. It organizes already existing real-time performance criteria and assessment techniques in a manner consistent with a well-formed process, based on the Personal Software Process concepts.

Advanced Communication Technology Satellite (ACTS) Multibeam Antenna On-Orbit Performance

Science.gov (United States)

1995-01-01

The NASA Lewis Research Center's Advanced Communication Technology Satellite (ACTS) was launched in September 1993. ACTS introduced several new technologies, including a multibeam antenna (MBA) operating at extremely short wavelengths never before used in communications. This antenna, which has both fixed and rapidly reconfigurable high-energy spot beams (150 miles in diameter), serves users equipped with small antenna terminals. Extensive structural and thermal analyses have been performed for simulating the ACTS MBA on-orbit performance. The results show that the reflector surfaces (mainly the front subreflector), antenna support assembly, and metallic surfaces on the spacecraft body will be distorted because of the thermal effects of varying solar heating, which degrade the ACTS MBA performance. Since ACTS was launched, a number of evaluations have been performed to assess MBA performance in the space environment. For example, the on-orbit performance measurements found systematic environmental disturbances to the MBA beam pointing. These disturbances were found to be imposed by the attitude control system, antenna and spacecraft mechanical alignments, and on-orbit thermal effects. As a result, the MBA may not always exactly cover the intended service area. In addition, the on-orbit measurements showed that antenna pointing accuracy is the performance parameter most sensitive to thermal distortions on the front subreflector surface and antenna support assemblies. Several compensation approaches were tested and evaluated to restore on-orbit pointing stability. A combination of autotrack (75 percent of the time) and Earth sensor control (25 percent of the time) was found to be the best way to compensate for antenna pointing error during orbit. This approach greatly minimizes the effects of thermal distortions on antenna beam pointing.

Performance-Based Technology Selection Filter description report

International Nuclear Information System (INIS)

O'Brien, M.C.; Morrison, J.L.; Morneau, R.A.; Rudin, M.J.; Richardson, J.G.

1992-05-01

A formal methodology has been developed for identifying technology gaps and assessing innovative or postulated technologies for inclusion in proposed Buried Waste Integrated Demonstration (BWID) remediation systems. Called the Performance-Based Technology Selection Filter, the methodology provides a formalized selection process where technologies and systems are rated and assessments made based on performance measures, and regulatory and technical requirements. The results are auditable, and can be validated with field data. This analysis methodology will be applied to the remedial action of transuranic contaminated waste pits and trenches buried at the Idaho National Engineering Laboratory (INEL)

Performance-Based Technology Selection Filter description report

Energy Technology Data Exchange (ETDEWEB)

O' Brien, M.C.; Morrison, J.L.; Morneau, R.A.; Rudin, M.J.; Richardson, J.G.

1992-05-01

A formal methodology has been developed for identifying technology gaps and assessing innovative or postulated technologies for inclusion in proposed Buried Waste Integrated Demonstration (BWID) remediation systems. Called the Performance-Based Technology Selection Filter, the methodology provides a formalized selection process where technologies and systems are rated and assessments made based on performance measures, and regulatory and technical requirements. The results are auditable, and can be validated with field data. This analysis methodology will be applied to the remedial action of transuranic contaminated waste pits and trenches buried at the Idaho National Engineering Laboratory (INEL).

Cooperation, Technology, and Performance: A Case Study.

Science.gov (United States)

Cavanagh, Thomas; Dickenson, Sabrina; Brandt, Suzanne

1999-01-01

Describes the CTP (Cooperation, Technology, and Performance) model and explains how it is used by the Department of Veterans Affairs-Veteran's Benefit Administration (VBA) for training. Discusses task analysis; computer-based training; cooperative-based learning environments; technology-based learning; performance-assessment methods; courseware…

A framework of performance criteria defining sustainable construction technologies

International Nuclear Information System (INIS)

Sturges, W.G.

1992-01-01

As our global culture encounters accelerating rates of resource depletion, environmental degradation, and societal inequality, it increasingly needs tools to rate building systems by environmental and socioeconomic criteria. By investigating light frame structural systems based on principles of ecological design, it is possible to not only identify the structures' potential impacts on the health of their site and larger community, but also to establish a framework of performance criteria for comparatively evaluating a variety of construction technologies. This paper summarizes the development and application of such a framework, based upon the ecosystems and culture of the Pacific Northwest's Cascadia Bioregion. The framework has been comparatively applied to solid-sawn lumber, trusses, and composite wood I-joists. These three framing technologies together represent traditional, contemporary, and progressive structural systems. Their individual and collective performance, based upon the application of the hypothesized criteria, offer insights into what might be a more ideal framing system of the sustainable future

Development of Integrated Assessment Technology of Risk and Performance

International Nuclear Information System (INIS)

Yang, Jun Eon; Kang, Dae Il; Kang, Hyun Gook

2010-04-01

The main idea and contents are summarized as below 1) Development of new risk/performance assessment system innovating old labor-intensive risk assessment structure - New consolidated risk assessment technology from various hazard(flood, fire, seismic in NPP) - BOP model development for performance monitoring - Consolidated risk/performance management system for consistency and efficiency of NPP 2) Resolution technology for pending issues in PSA - Base technology for PSA of digital I and C system - Base technology for seismic PSA reflecting domestic seismic characteristics and aging effect - Uncertainty reduction technology for level 2 PSA and best estimation of containment failure frequency 3) Next generation risk/performance assessment technology - Human-induced error reduction technology for efficient operation of a NPP

Arsenic Removal from Drinking Water by Point of Entry/Point of Use Adsorptive Media U.S. EPA Demonstration Project at Oregon Institute of Technology at Klamath Falls, OR - Final Performance Evaluation Report

Science.gov (United States)

This report documents the activities performed during and the results obtained from the arsenic removal treatment technology demonstration project at Oregon Institute of Technology (OIT) at Klamath Falls, OR. The objectives of the project were to evaluate: (1) the effectiveness...

Evaluation of soil characterization technologies using a stochastic, value-of-information approach

International Nuclear Information System (INIS)

Kaplan, P.G.

1993-01-01

The US Department of Energy has initiated an integrated demonstration program to develop and compare new technologies for the characterization of uranium-contaminated soils. As part of this effort, a performance-assessment task was funded in February, 1993 to evaluate the field tested technologies. Performance assessment can be cleaned as the analysis that evaluates a system's, or technology's, ability to meet the criteria specified for performance. Four new technologies were field tested at the Fernald Environmental Management Restoration Co. in Ohio. In the next section, the goals of this performance assessment task are discussed. The following section discusses issues that must be resolved if the goals are to be successfully met. The author concludes with a discussion of the potential benefits to performance assessment of the approach taken. This paper is intended to be the first of a series of documentation that describes the work. Also in this proceedings is a paper on the field demonstration at the Fernald site and a description of the technologies (Tidwell et al, 1993) and a paper on the application of advanced geostatistical techniques (Rautman, 1993). The overall approach is to simply demonstrate the applicability of concepts that are well described in the literature but are not routinely applied to problems in environmental remediation, restoration, and waste management. The basic geostatistical concepts are documented in Clark (1979) and in Issaks and Srivastava (1989). Advanced concepts and applications, along with software, are discussed in Deutsch and Journel (1992). Integration of geostatistical modeling with a decision-analytic framework is discussed in Freeze et al (1992). Information-theoretic and probabilistic concepts are borrowed from the work of Shannon (1948), Jaynes (1957), and Harr (1987). The author sees the task as one of introducing and applying robust methodologies with demonstrated applicability in other fields to the problem at hand

NREL Evaluates Performance of Hydraulic Hybrid Refuse Vehicles

Energy Technology Data Exchange (ETDEWEB)

2015-09-01

This highlight describes NREL's evaluation of the in-service performance of 10 next-generation hydraulic hybrid refuse vehicles (HHVs), 8 previous-generation (model year 2013) HHVs, and 8 comparable conventional diesel vehicles operated by Miami-Dade County's Public Works and Waste Management Department in southern Florida. Launched in March 2015, the on-road portion of this 12-month evaluation focuses on collecting and analyzing vehicle performance data - fuel economy, maintenance costs, and drive cycles - from the HHVs and the conventional diesel vehicles. The fuel economy of heavy-duty vehicles, such as refuse trucks, is largely dependent on the load carried and the drive cycles on which they operate. In the right applications, HHVs offer a potential fuel-cost advantage over their conventional counterparts. This advantage is contingent, however, on driving behavior and drive cycles with high kinetic intensity that take advantage of regenerative braking. NREL's evaluation will assess the performance of this technology in commercial operation and help Miami-Dade County determine the ideal routes for maximizing the fuel-saving potential of its HHVs. Based on the field data, NREL will develop a validated vehicle model using the Future Automotive Systems Technology Simulator, also known as FASTSim, to study the impacts of route selection and other vehicle parameters. NREL is also analyzing fueling and maintenance data to support total-cost-of-ownership estimations and forecasts. The study aims to improve understanding of the overall usage and effectiveness of HHVs in refuse operation compared to similar conventional vehicles and to provide unbiased technical information to interested stakeholders.

Weapons of Mass Destruction Technology Evaluation and Training Range

Energy Technology Data Exchange (ETDEWEB)

Kevin Larry Young

2009-05-01

The Idaho National Laboratory (INL) has a long history for providing technology evaluation and training for military and other federal level Weapons of Mass Destruction (WMD) response agencies. Currently there are many federal organizations and commercial companies developing technologies related to detecting, assessing, mitigating and protecting against hazards associated with a WMD event. Unfortunately, very few locations exist within the United States where WMD response technologies are realistically field tested and evaluated using real chemical, biological, radiological, nuclear and explosive materials. This is particularly true with biological and radiological hazards. Related to this lack of adequate WMD, multi-hazard technology testing capability is the shortage of locations where WMD response teams can train using actual chemical, biological, and radiological material or highly realistic simulates. In response to these technology evaluation and training needs, the INL has assembled a consortium of subject matter experts from existing programs and identified dedicated resources for the purpose of establishing an all-hazards, WMD technology evaluation and training range. The author describes the challenges associated with creating the all-hazards WMD technology evaluation and training range and lists the technical, logistical and financial benefits of an all-hazards technology evaluation and training range. Current resources and capabilities for conducting all-hazard technology evaluation and training at the INL are identified. Existing technology evaluation and training programs at the INL related to radiological, biological and chemical hazards are highlighted, including successes and lessons learned. Finally, remaining gaps in WMD technology evaluation and training capabilities are identified along with recommendations for closing those gaps.

Establishment of a Quantitative Medical Technology Evaluation System and Indicators within Medical Institutions

Directory of Open Access Journals (Sweden)

Suo-Wei Wu

2018-01-01

Conclusions: As the two-round questionnaire survey of experts and statistical analysis were performed and credibility of the results was verified through consistency evaluation test, the study established a quantitative medical technology evaluation system model and assessment indicators within medical institutions based on the Delphi method and analytical hierarchy process. Moreover, further verifications, adjustments, and optimizations of the system and indicators will be performed in follow-up studies.

Electrification Futures Study: End-Use Electric Technology Cost and Performance Projections through 2050

Energy Technology Data Exchange (ETDEWEB)

Vimmerstedt, Laura J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jadun, Paige [National Renewable Energy Lab. (NREL), Golden, CO (United States); McMillan, Colin A. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Steinberg, Daniel C. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Muratori, Matteo [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mai, Trieu T. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2018-01-02

This report provides projected cost and performance assumptions for electric technologies considered in the Electrification Futures Study, a detailed and comprehensive analysis of the effects of widespread electrification of end-use service demands in all major economic sectors - transportation, residential and commercial buildings, and industry - for the contiguous United States through 2050. Using extensive literature searches and expert assessment, the authors identify slow, moderate, and rapid technology advancement sensitivities on technology cost and performance, and they offer a comparative analysis of levelized cost metrics as a reference indicator of total costs. The identification and characterization of these end-use service demand technologies is fundamental to the Electrification Futures Study. This report, the larger Electrification Futures Study, and the associated data and methodologies may be useful to planners and analysts in evaluating the potential role of electrification in an uncertain future. The report could be broadly applicable for other analysts and researchers who wish to assess electrification and electric technologies.

Let's get technical: Enhancing program evaluation through the use and integration of internet and mobile technologies.

Science.gov (United States)

Materia, Frank T; Miller, Elizabeth A; Runion, Megan C; Chesnut, Ryan P; Irvin, Jamie B; Richardson, Cameron B; Perkins, Daniel F

2016-06-01

Program evaluation has become increasingly important, and information on program performance often drives funding decisions. Technology use and integration can help ease the burdens associated with program evaluation by reducing the resources needed (e.g., time, money, staff) and increasing evaluation efficiency. This paper reviews how program evaluators, across disciplines, can apply internet and mobile technologies to key aspects of program evaluation, which consist of participant registration, participant tracking and retention, process evaluation (e.g., fidelity, assignment completion), and outcome evaluation (e.g., behavior change, knowledge gain). In addition, the paper focuses on the ease of use, relative cost, and fit with populations. An examination on how these tools can be integrated to enhance data collection and program evaluation is discussed. Important limitations of and considerations for technology integration, including the level of technical skill, cost needed to integrate various technologies, data management strategies, and ethical considerations, are highlighted. Lastly, a case study of technology use in an evaluation conducted by the Clearinghouse for Military Family Readiness at Penn State is presented and illustrates how technology integration can enhance program evaluation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Definition and compositions of standard wastestreams for evaluation of Buried Waste Integrated Demonstration treatment technologies

International Nuclear Information System (INIS)

Bates, S.O.

1993-06-01

The Buried Waste Integrated Demonstration (BWID) Project was organized at the Idaho National Engineering Laboratory to support research, development, demonstration, testing, and evaluation of emerging technologies that offer promising solutions to remediation of buried waste. BWID will identify emerging technologies, screen them for applicability to the identified needs, select technologies for demonstration, and then evaluate the technologies based on prescribed performance objectives. The technical objective of the project is to establish solutions to Environmental Restoration and Waste Management's technological deficiencies and improve baseline remediation systems. This report establishes a set of standard wastestream compositions that will be used by BWID to evaluate the emerging technologies. Five wastestreams are proposed that use four types of waste and a nominal case that is a homogenized combination of the four wastes. The five wastestreams will provide data on the compositional extremes and indicate the technologies' effectiveness over the complete range of expected wastestream compositions

Identification and Evaluation of Human Factors Issues Associated with Emerging Nuclear Plant Technology

International Nuclear Information System (INIS)

O'Hara, J.M.; Higgins, J.; Brown, William S.

2009-01-01

This study has identified human performance research issues associated with the implementation of new technology in nuclear power plants (NPPs). To identify the research issues, current industry developments and trends were evaluated in the areas of reactor technology, instrumentation and control technology, human-system integration technology, and human factors engineering (HFE) methods and tools. The issues were prioritized into four categories based on evaluations provided by 14 independent subject matter experts representing vendors, utilities, research organizations and regulators. Twenty issues were categorized into the top priority category. The study also identifies the priority of each issue and the rationale for those in the top priority category. The top priority issues were then organized into research program areas of: New Concepts of Operation using Multi-agent Teams, Human-system Interface Design, Complexity Issues in Advanced Systems, Operating Experience of New and Modernized Plants, and HFE Methods and Tools. The results can serve as input to the development of a long-term strategy and plan for addressing human performance in these areas to support the safe operation of new NPPs.

Public participation in the evaluation of innovative environmental cleanup technology

International Nuclear Information System (INIS)

Peterson, T.; McCabe, G.; Serie, P.; Niesen, K.

1994-08-01

Technologies for remediation of contamination are urgently needed to clean up US Department of Energy (DOE) sites across the country. DOE is managing a national program to develop, demonstrate, and deploy new technologies with promise to expedite this cleanup. The Integrated Demonstration for Cleanup of Volatile Organic Compounds at Arid Sites (VOC-Arid ID) is one such effort. Time and resources, however, are too limited to be invested in methods of remediation that will never be deployed because they have not been rigorously evaluated or because they face the withering opposition of stakeholders. Therefore the VOC-Arid ID is assessing technology both in terms of its technical effectiveness and its stakeholder acceptability. Only if a technology performs as required and is acceptable to regulators, users of technology, and the public will the VOC-Arid ID recommend its use. What distinguishes public involvement in the VOC-Arid ID is the direct influence stakeholders have on the design of technology demonstrations by working directly with technology developers. Stakeholders participated in defining the criteria with which innovative environmental cleanup technology is being evaluated. The integrated demonstration is committed to providing stakeholders with the information they've indicated they need to reach reasoned judgments about the use of specific cleanup technologies. A guiding principle of the VOC-Arid ID is that stakeholder participation improves the technologies being developed, enhances the acceptance of the technologies, and will lead to the broad and timely deployment of appropriate and effective methods of environmental remediation. The VOC-Arid ID has involved stakeholders from the host demonstration site, Hanford, Washington, and from other and sites where the ID technologies may be deployed

Designing and Implementing Performance Technology for Teachers

Directory of Open Access Journals (Sweden)

Joi L. Moore

2004-06-01

Full Text Available This paper synthesizes research findings from a performance analysis of teacher tasks and the implementation of performance technology. These findings are aligned with design and implementation theories to provide understanding of the complex factors and events that occur during the implementation process. The article describes the necessary elements and conditions for designing and implementing performance tools in school environments that will encourage usage, efficient performance, and positive attitudes. Two models provide a visual representation of causal relationships between the implementation factors and the technology user. Although the implementation process can become complex because of the simultaneous events and phases, it can be properly managed through good communication and strategic involvement of teachers during the design and development process. The models may be able to assist technology designers and advocates with presenting innovations to teachers who are frequently asked to try technical solutions for performance support or improvement.

The Effect of Using in Computer Skills on Teachers’ Perceived Self-Efficacy Beliefs Towards Technology Integration, Attitudes and Performance

Directory of Open Access Journals (Sweden)

Badrie Mohammad Nour EL-Daou

2016-07-01

Full Text Available The current study analyzes the relationship between the apparent teacher’s Self-efficacy and attitudes towards integrating technology into classroom teaching, self- evaluation reports and computer performance results. Pre-post measurement of the Computer Technology Integration Survey (CTIS (Wang et al,2004 was used to determine the confidence level with of 60 science teachers and 12 mixed-major teachers enrolled at the Lebanese University, Faculty of Education in the academic year 2011-2012. Pre –post measurement on teachers’ attitudes towards using technology was examined using an opened and a closed questionnaire. Teachers’ performance was measured by means of their Activeinspire projects results using active boards after their third practice of training in computer skills and Activeinspire program. To accumulate data on teachers’ self-report, this study uses Robert Reasoner's five components: feeling of security, feeling of belonging, feeling of identity, feeling of goal, and self-actualization which teachers used to rate themselves (Reasoner,1983. The study acknowledged probable impacts of computer training skills on teachers ‘self-evaluation report, effectiveness of computer technology skills, and evaluations of self-efficacy attitudes toward technology integration. Pearson correlation revealed a strong relationship r = 0.99 between the perceived self-efficacy towards technology incorporation and teachers’ self-evaluation report. Also, the findings of this research revealed that 82.7% of teachers earned high computer technology scores on their Activeinspire projects and 33.3% received excellent grades on computer performance test. Recommendations and potential research were discussed.

Improving early cycle economic evaluation of diagnostic technologies

NARCIS (Netherlands)

Steuten, Lotte Maria Gertruda; Ramsey, Scott D.

2014-01-01

The rapidly increasing range and expense of new diagnostics, compels consideration of a different, more proactive approach to health economic evaluation of diagnostic technologies. Early cycle economic evaluation is a decision analytic approach to evaluate technologies in development so as to

Performance evaluation of various cryogenic energy storage systems

International Nuclear Information System (INIS)

Abdo, Rodrigo F.; Pedro, Hugo T.C.; Koury, Ricardo N.N.; Machado, Luiz; Coimbra, Carlos F.M.; Porto, Matheus P.

2015-01-01

This work compares various CES (cryogenic energy storage) systems as possible candidates to store energy from renewable sources. Mitigating solar and wind power variability and its direct effect on local grid stability are already a substantial technological bottleneck for increasing market penetration of these technologies. In this context, CES systems represent low-cost solutions for variability that can be used to set critical power ramp rates. We investigate the different thermodynamic and engineering constraints that affect the design of CES systems, presenting theoretical simulations, indicating that optimization is also needed to improve the cryogenic plant performance. - Highlights: • We assessed the performance of cryogenic energy storage systems. • We re-evaluated the Linde–Hampson cycle proposed by Chen. • We proposed the Claude and Collins cycles as alternatives for the Linde–Hampson cycle. • We concluded that Claude cycle is the best alternative for the simulated conditions.

Structured Innovation of High-Performance Wave Energy Converter Technology: Preprint

Energy Technology Data Exchange (ETDEWEB)

Weber, Jochem W. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Laird, Daniel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2018-01-25

Wave energy converter (WEC) technology development has not yet delivered the desired commercial maturity nor, and more importantly, the techno-economic performance. The reasons for this have been recognized and fundamental requirements for successful WEC technology development have been identified. This paper describes a multi-year project pursued in collaboration by the National Renewable Energy Laboratory and Sandia National Laboratories to innovate and develop new WEC technology. It specifies the project strategy, shows how this differs from the state-of-the-art approach and presents some early project results. Based on the specification of fundamental functional requirements of WEC technology, structured innovation and systemic problem solving methodologies are applied to invent and identify new WEC technology concepts. Using Technology Performance Levels (TPL) as an assessment metric of the techno-economic performance potential, high performance technology concepts are identified and selected for further development. System performance is numerically modelled and optimized and key performance aspects are empirically validated. The project deliverables are WEC technology specifications of high techno-economic performance technologies of TPL 7 or higher at TRL 3 with some key technology challenges investigated at higher TRL. These wave energy converter technology specifications will be made available to industry for further, full development and commercialisation (TRL 4 - TRL 9).

Integrating Human Performance and Technology

International Nuclear Information System (INIS)

Farris, Ronald K.; Medema, Heather

2012-01-01

Human error is a significant factor in the cause and/or complication of events that occur in the commercial nuclear industry. In recent years, great gains have been made using Human Performance (HU) tools focused on targeting individual behaviors. However, the cost of improving HU is growing and resistance to add yet another HU tool certainly exists, particularly for those tools that increase the paperwork for operations. Improvements in HU that are the result of leveraging existing technology, such as hand-held mobile technologies, have the potential to reduce human error in controlling system configurations, safety tag-outs, and other verifications. Operator rounds, valve lineup verifications, containment closure verifications, safety and equipment protection, and system tagging can be supported by field-deployable wireless technologies. These devices can also support the availability of critical component data in the main control room and other locations. This research pilot project reviewing wireless hand-held technology is part of the Light Water Reactor Sustainability Program (LWRSP), a research and development (R and D) program sponsored by the U. S. Department of Energy (DOE). The project is being performed in close collaboration with industry R and D programs to provide the technical foundations for licensing, and managing the long-term, safe, and economical operation of current nuclear power plants. The LWRSP vision is to develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the life of the current nuclear reactor fleet. (author)

Integrating Human Performance and Technology

Energy Technology Data Exchange (ETDEWEB)

Ronald K. Farris; Heather Medema

2012-05-01

Human error is a significant factor in the cause and/or complication of events that occur in the commercial nuclear industry. In recent years, great gains have been made using Human Performance (HU) tools focused on targeting individual behaviors. However, the cost of improving HU is growing and resistance to add yet another HU tool certainly exists, particularly for those tools that increase the paperwork for operations. Improvements in HU that are the result of leveraging existing technology, such as hand-held mobile technologies, have the potential to reduce human error in controlling system configurations, safety tag-outs, and other verifications. Operator rounds, valve line-up verifications, containment closure verifications, safety & equipment protection, and system tagging can be supported by field-deployable wireless technologies. These devices can also support the availability of critical component data in the main control room and other locations. This research pilot project reviewing wireless hand-held technology is part of the Light Water Reactor Sustainability Program (LWRSP), a research and development (R&D) program sponsored by the U. S. Department of Energy (DOE). The project is being performed in close collaboration with industry R&D programs to provide the technical foundations for licensing, and managing the long-term, safe, and economical operation of current nuclear power plants. The LWRSP vision is to develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the life of the current nuclear reactor fleet.

A new method to evaluate human-robot system performance

Science.gov (United States)

Rodriguez, G.; Weisbin, C. R.

2003-01-01

One of the key issues in space exploration is that of deciding what space tasks are best done with humans, with robots, or a suitable combination of each. In general, human and robot skills are complementary. Humans provide as yet unmatched capabilities to perceive, think, and act when faced with anomalies and unforeseen events, but there can be huge potential risks to human safety in getting these benefits. Robots provide complementary skills in being able to work in extremely risky environments, but their ability to perceive, think, and act by themselves is currently not error-free, although these capabilities are continually improving with the emergence of new technologies. Substantial past experience validates these generally qualitative notions. However, there is a need for more rigorously systematic evaluation of human and robot roles, in order to optimize the design and performance of human-robot system architectures using well-defined performance evaluation metrics. This article summarizes a new analytical method to conduct such quantitative evaluations. While the article focuses on evaluating human-robot systems, the method is generally applicable to a much broader class of systems whose performance needs to be evaluated.

Evaluation of Adaptive Noise Management Technologies for School-Age Children with Hearing Loss.

Science.gov (United States)

Wolfe, Jace; Duke, Mila; Schafer, Erin; Jones, Christine; Rakita, Lori

2017-05-01

Children with hearing loss experience significant difficulty understanding speech in noisy and reverberant situations. Adaptive noise management technologies, such as fully adaptive directional microphones and digital noise reduction, have the potential to improve communication in noise for children with hearing aids. However, there are no published studies evaluating the potential benefits children receive from the use of adaptive noise management technologies in simulated real-world environments as well as in daily situations. The objective of this study was to compare speech recognition, speech intelligibility ratings (SIRs), and sound preferences of children using hearing aids equipped with and without adaptive noise management technologies. A single-group, repeated measures design was used to evaluate performance differences obtained in four simulated environments. In each simulated environment, participants were tested in a basic listening program with minimal noise management features, a manual program designed for that scene, and the hearing instruments' adaptive operating system that steered hearing instrument parameterization based on the characteristics of the environment. Twelve children with mild to moderately severe sensorineural hearing loss. Speech recognition and SIRs were evaluated in three hearing aid programs with and without noise management technologies across two different test sessions and various listening environments. Also, the participants' perceptual hearing performance in daily real-world listening situations with two of the hearing aid programs was evaluated during a four- to six-week field trial that took place between the two laboratory sessions. On average, the use of adaptive noise management technology improved sentence recognition in noise for speech presented in front of the participant but resulted in a decrement in performance for signals arriving from behind when the participant was facing forward. However, the improvement

The evaluation of supply chain performance in the Oil Products Distribution Company, using information technology indicators and fuzzy TOPSIS technique

Directory of Open Access Journals (Sweden)

Daryosh Mohamadi Janaki

2018-08-01

Full Text Available Information Technology (IT plays an essential role on development of effective supply chain planning and it can improve the supply chain performance, either directly or indirectly. As a national industry, the National Iranian Oil Products Distribution Company involves a large number of organizations within its supply chain. Therefore, this descriptive-survey uses information sharing indicators, fuzzy TOPSIS technique based on managers and expert opinions to evaluate and to rank some oil products distribution companies. Data are analyzed and the results show that Oil Products Distribution Company of Chaharmahal and Bakhtiari received the highest rank and Farsan maintained the lowest rank compared with other regional companies.

Experimental Evaluation for the Microvibration Performance of a Segmented PC Method Based High Technology Industrial Facility Using 1/2 Scale Test Models

Directory of Open Access Journals (Sweden)

Sijun Kim

2017-01-01

Full Text Available The precast concrete (PC method used in the construction process of high technology industrial facilities is limited when applied to those with greater span lengths, due to the transport length restriction (maximum length of 15~16 m in Korea set by traffic laws. In order to resolve this, this study introduces a structural system with a segmented PC system, and a 1/2 scale model with a width of 9000 mm (hereafter Segmented Model is manufactured to evaluate vibration performance. Since a real vibrational environment cannot be reproduced for vibration testing using a scale model, a comparative analysis of their relative performances is conducted in this study. For this purpose, a 1/2 scale model with a width of 7200 mm (hereafter Nonsegmented Model of a high technology industrial facility is additionally prepared using the conventional PC method. By applying the same experiment method for both scale models and comparing the results, the relative vibration performance of the Segmented Model is observed. Through impact testing, the natural frequencies of the two scale models are compared. Also, in order to analyze the estimated response induced by the equipment, the vibration responses due to the exciter are compared. The experimental results show that the Segmented Model exhibits similar or superior performances when compared to the Nonsegmented Model.

Development of inspection safety evaluation technology

Energy Technology Data Exchange (ETDEWEB)

Yoon, Seok Chul; Yoon, Yeo Chang; Kim, Jong Soo; Lee, Tae Young; Kim, Chang Ryol; Lee, Hyung Sub; Kim, Jong Soo

1995-12-01

The purpose of this project is to protection nation inspector`s over exposure from radiation that can be occurred by inspection activity at nuclear facilities and its environment, and to ensure the safety of inspection activity at the nuclear facilities. To effectively carry out the domestic inspection task to be enforced from 1996, the evaluation for special radiation exposure rate of nuclear facilities, air and surface contamination level, and measurement and monitoring of water contamination level were made to determine whether these measured values exceeded permissible limitations, and to protect the inspector`s over exposure from radiation at domestic nuclear facilities. Management of inspector`s exposure was carried out under assistance of the Department of Health Physics. Performance tests of two gamma detectors, one neutron detector, alpha and beta detector, and gamma spectroscopy analyzer were carried out to control dose on extremity, the characteristic test for extremity dosimeter was carried out and the theoretical calculation of gamma dose conversion factors based on ANSI N13.32 standard was performed. Under the 93+2 program, IAEA began to recognize the necessity of environmental observation technology development of air-borne particulates travelled from long distance location. Associated with the necessity of this technology development, a proposal of international joint research for development of the special radiation measurement and analysis has been prepared. (author). 21 tabs., 24 figs., 20 refs.

Manufacturing plant performance evaluation by discrete event simulation

International Nuclear Information System (INIS)

Rosli Darmawan; Mohd Rasid Osman; Rosnah Mohd Yusuff; Napsiah Ismail; Zulkiflie Leman

2002-01-01

A case study was conducted to evaluate the performance of a manufacturing plant using discrete event simulation technique. The study was carried out on animal feed production plant. Sterifeed plant at Malaysian Institute for Nuclear Technology Research (MINT), Selangor, Malaysia. The plant was modelled base on the actual manufacturing activities recorded by the operators. The simulation was carried out using a discrete event simulation software. The model was validated by comparing the simulation results with the actual operational data of the plant. The simulation results show some weaknesses with the current plant design and proposals were made to improve the plant performance. (Author)

Image processing system performance prediction and product quality evaluation

Science.gov (United States)

Stein, E. K.; Hammill, H. B. (Principal Investigator)

1976-01-01

The author has identified the following significant results. A new technique for image processing system performance prediction and product quality evaluation was developed. It was entirely objective, quantitative, and general, and should prove useful in system design and quality control. The technique and its application to determination of quality control procedures for the Earth Resources Technology Satellite NASA Data Processing Facility are described.

Innovative technology transfer of nondestructive evaluation research

Science.gov (United States)

Brian Brashaw; Robert J. Ross; Xiping Wang

2008-01-01

Technology transfer is often an afterthought for many nondestructive evaluation (NDE) researchers. Effective technology transfer should be considered during the planning and execution of research projects. This paper outlines strategies for using technology transfer in NDE research and presents a wide variety of technology transfer methods used by a cooperative...

The effect of using in computer skills on teachers’ perceived self-efficacy beliefs towards technology integration, attitudes and performance

Directory of Open Access Journals (Sweden)

Badrie Mohammad Nour ELDaou

2016-10-01

Full Text Available The current study analyzesthe relationship between the apparentteacher’s Self-efficacyand attitudes towardsintegrating technology into classroom teaching, self-evaluation reportsand computer performance results. Pre-post measurement of the Computer Technology Integration Survey (CTIS (Wang et al, 2004 was used to determine theconfidence level with of 60 science teachers and 12 mixed-major teachers enrolled at the Lebanese University, Faculty of Education in the academic year 2011-2012. Pre –post measurement onteachers’attitudes towards usingtechnologywas examined using an opened and a closed questionnaire.Teachers’ performance was measured by means of their Activeinspire projects results using active boards after their third practice of training in computer skills and Activeinspire program. To accumulate data on teachers’ self-report, this study uses Robert Reasoner's five components: feeling of security, feeling of belonging, feeling of identity, feeling of goal, and self-actualization which teachers used to rate themselves (Reasoner,1983. The study acknowledged probable impacts of computer training skills on teachers ‘self-evaluation report, effectiveness of computer technology skills, and evaluations of self-efficacy attitudes toward technology integration. Pearson correlation revealed a strong relationship r= 0.99 between the perceived self-efficacy towards technology incorporation and teachers’ self-evaluation report. Also, the findings of this research revealed that 82.7% of teachers earned high computer technology scores on their Activeinspire projects and 33.3% received excellent grades on computer performance test. Recommendations and potential research were discussed

Effect of information and communication technology on nursing performance.

Science.gov (United States)

Fujino, Yuriko; Kawamoto, Rieko

2013-05-01

The aim of this study was to investigate the influence of information and communication technology use and skills on nursing performance. Questionnaires were prepared relating to using the technology, practical skills in utilizing information, the Six-Dimension Scale of Nursing Performance, and demographics. In all, 556 nurses took part (response rate, 72.6%). A two-way analysis of variance was used to determine the influence of years of nursing experience on the relationship between nursing performance and information and communication technology use. The results showed that the group possessing high technological skills had greater nursing ability than the group with low skills; the level of nursing performance improved with years of experience in the former group, but not in the latter group. Regarding information and communication technology use, the results showed that nursing performance improved among participants who used computers for sending and receiving e-mails, but it decreased for those who used cell phones for e-mail. The results suggest that nursing performance may be negatively affected if information and communication technology are inappropriately used. Informatics education should therefore be provided for all nurses, and it should include information use relating to cell phones and computers.

Students’ Perception on Teaching Practicum Evaluation using Video Technology

Science.gov (United States)

Chee Sern, Lai; ‘Ain Helan Nor, Nurul; Foong, Lee Ming; Hassan, Razali

2017-08-01

Video technology has been widely used in education especially in teaching and learning. However, the use of video technology for evaluation purpose especially in teaching practicum is extremely scarce and the benefits of video technology in teaching practicum evaluation have not yet been fully discovered. For that reason, this quantitative research aimed at identifying the perceptions of trainee teachers towards teaching practicum evaluation via video technology. A total of 260 students of Teacher Certification Programme (Program Pensiswazahan Guru - PPG) from the Faculty of Technical and Vocational Education (FPTV) of Universiti Tun Hussein Onn Malaysia (UTHM) had been randomly selected as respondents. A set of questionnaire was developed to assess the suitability, effectiveness and satisfaction of using video technology for teaching practicum. Conclusively, this research showed that the trainee teachers have positive perceptions in all three aspects related teaching practicum evaluation using video technology. Apart from that, no significant racial difference was found in the measured aspects. In addition, the trainee teachers also showed an understanding of the vast importance of teaching practicum evaluation via video. These research findings suggest that video technology can be a feasible and practical means of teaching practicum evaluation especially for distance learning program.

Low carbon technology performance vs infrastructure vulnerability: analysis through the local and global properties space.

Science.gov (United States)

Dawson, David A; Purnell, Phil; Roelich, Katy; Busch, Jonathan; Steinberger, Julia K

2014-11-04

Renewable energy technologies, necessary for low-carbon infrastructure networks, are being adopted to help reduce fossil fuel dependence and meet carbon mitigation targets. The evolution of these technologies has progressed based on the enhancement of technology-specific performance criteria, without explicitly considering the wider system (global) impacts. This paper presents a methodology for simultaneously assessing local (technology) and global (infrastructure) performance, allowing key technological interventions to be evaluated with respect to their effect on the vulnerability of wider infrastructure systems. We use exposure of low carbon infrastructure to critical material supply disruption (criticality) to demonstrate the methodology. A series of local performance changes are analyzed; and by extension of this approach, a method for assessing the combined criticality of multiple materials for one specific technology is proposed. Via a case study of wind turbines at both the material (magnets) and technology (turbine generators) levels, we demonstrate that analysis of a given intervention at different levels can lead to differing conclusions regarding the effect on vulnerability. Infrastructure design decisions should take a systemic approach; without these multilevel considerations, strategic goals aimed to help meet low-carbon targets, that is, through long-term infrastructure transitions, could be significantly jeopardized.

Bookline: a technological tool at service of scientific papers evaluation in academic events

Directory of Open Access Journals (Sweden)

Cênio Back Weyh

2016-12-01

Full Text Available The use of technologies has been more common each day in teaching. The softwares that facilitate the teacher’s work as a technological source can also be used for other aspects of education. The scientific events are fundamental for the particular student’s learnings in higher education. Considering the complexity of coordinating an event due to the number of people involved and the means of sending works for analysis and their evaluation during the event, we looked forward to developing technological tools. In this sense, we developed a software to manage scientific events providing an interface for the organization of the works’ evaluation and of the criteria for evaluation, as well as the management of evaluators and their thematic areas of performance. The software named Bookline was designed for mobile environments, making it possible for the evaluators to wander around freely during the evaluations, getting additional information about each criterion of evaluation, in order to enable the widest spectrum in the constitution of the work’s mark. At the end of the evaluations, the evaluator sends his considerations to the central server, that processes and compiles its data and from the rest of the evaluators identifying if the work was accepted.

Process is king: Evaluating the performance of technology-mediated learning in vocational software training

OpenAIRE

Söllner, Matthias; Bitzer, Philipp; Janson, Andreas; Leimeister, Jan Marco

2017-01-01

Technology-mediated learning (TML) is a major trend in education, since it allows to integrate the strengths of traditional- and IT-based learning activities. However, TML providers still struggle in identifying areas for improvement in their TML offerings. One reason for their struggles is inconsistencies in the literature regarding drivers of TML performance. Prior research suggests that these inconsistencies in TML literature might stem from neglecting the importance of considering the pro...

40 CFR 63.2354 - What performance tests, design evaluations, and performance evaluations must I conduct?

Science.gov (United States)

2010-07-01

... evaluations, and performance evaluations must I conduct? 63.2354 Section 63.2354 Protection of Environment... tests, design evaluations, and performance evaluations must I conduct? (a)(1) For each performance test... procedures specified in subpart SS of this part. (3) For each performance evaluation of a continuous emission...

Transferability of economic evaluations of medical technologies: a new technology for orthopedic surgery.

Science.gov (United States)

Steuten, Lotte; Vallejo-Torres, Laura; Young, Terry; Buxton, Martin

2008-05-01

Transferring results of economic evaluations across countries or jurisdictions can potentially save scarce evaluation resources while helping to make market access and reimbursement decisions in a timely fashion. This article points out why transferring results of economic evaluations is particularly important in the field of medical technologies. It then provides an overview of factors that are previously identified in the literature as affecting transferability of economic evaluations, as well as methods for transferring results in a scientifically sound way. As the current literature almost exclusively relates to transferability of pharmacoeconomic evaluations, this article highlights those factors and methodologies that are of particular relevance to transferring medical technology assessments. Considering the state-of-the-art literature and a worked, real life, example of transferring an economic evaluation of a product used in orthopedic surgery, we provide recommendations for future work in this important area of medical technology assessment.

Evaluative conditioning of food technologies in China

DEFF Research Database (Denmark)

Loebnitz, Natascha; Grunert, Klaus G

2014-01-01

This study provides an initial examination of the evaluative conditioning (EC) of consumers’ attitudes toward food technologies in China, including how EC can affect consumer acceptance of new technology when participants possess different levels of social trust. In a study using the EC paradigm...... and a combination of between-subjects control groups and within-subjects control conditions, participants considered three food technologies (conventional, enzyme, and genetic), paired with affectively positive, neutral, and negative images. Subsequent evaluative measurements revealed that EC can explain attitude...... formation toward food technologies in China when consumers see affective images, but the strength of the effects varies at different levels of social trust. Participants with a high level of trust in the institutions that promote and regulate the technologies can be conditioned both positively...

Improving early cycle economic evaluation of diagnostic technologies.

Science.gov (United States)

Steuten, Lotte M G; Ramsey, Scott D

2014-08-01

The rapidly increasing range and expense of new diagnostics, compels consideration of a different, more proactive approach to health economic evaluation of diagnostic technologies. Early cycle economic evaluation is a decision analytic approach to evaluate technologies in development so as to increase the return on investment as well as patient and societal impact. This paper describes examples of 'early cycle economic evaluations' as applied to diagnostic technologies and highlights challenges in its real-time application. It shows that especially in the field of diagnostics, with rapid technological developments and a changing regulatory climate, early cycle economic evaluation can have a guiding role to improve the efficiency of the diagnostics innovation process. In the next five years the attention will move beyond the methodological and analytic challenges of early cycle economic evaluation towards the challenge of effectively applying it to improve diagnostic research and development and patient value. Future work in this area should therefore be 'strong on principles and soft on metrics', that is, the metrics that resonate most clearly with the various decision makers in this field.

Acting with Technology: Rehearsing for Mixed-Media Live Performances

DEFF Research Database (Denmark)

Barkhuus, Louise; Rossitto, Chiara

2016-01-01

require a different type of engagement from the actors and rehearsing is challenging, as it can be impossible to rehearse with all the functional technology and interaction. Here, we report experiences from a case study of two mixed-media performances; we studied the rehearsal practices of two actors who......Digital technologies provide theater with new possibilities for combining traditional stage-based performances with interactive artifacts, for streaming remote parallel performances and for other device facilitated audience interaction. Compared to traditional theater, mixed-media performances...... and mixed media performances through addressing critical factors of implementing technology into rehearsal practices....

Evaluation of Coating Removal and Aggressive Surface Removal Surface Technologies Applied to Concrete Walls, Brick Walls, and Concrete Ceilings

International Nuclear Information System (INIS)

Ebadian, M.A.; Lagos, L.E.

1997-01-01

The purpose of this investigation was to test and evaluate innovative and commercially available technologies for the surface decontamination of walls and ceilings. This investigation supports the DOE's objectives of reducing risks to human health and the environment through its restoration projects at FEMP and MEMP. This project was performed at the Hemispheric Center for Environmental Technology (HCET) at Florida International University (FIU), where one innovative and four commercially available decontamination technologies were evaluated under standard, non-nuclear testing conditions. The performance data generated by this project will assist DOE site managers in the selection of the safest, most efficient, and most cost-effective decontamination technologies to accomplish their remediation objectives

Project Startup: Evaluating the Performance of Hydraulic Hybrid Refuse Vehicles

Energy Technology Data Exchange (ETDEWEB)

2015-09-01

The Fleet Test and Evaluation Team at the National Renewable Energy Laboratory (NREL) is evaluating the in-service performance of 10 next-generation hydraulic hybrid refuse vehicles (HHVs), 8 previous-generation HHVs, and 8 comparable conventional diesel vehicles operated by Miami-Dade County's Public Works and Waste Management Department in southern Florida. The HHVs under study - Autocar E3 refuse trucks equipped with Parker Hannifin's RunWise Advanced Series Hybrid Drive systems - can recover as much as 70 percent of the energy typically lost during braking and reuse it to power the vehicle. NREL's evaluation will assess the performance of this technology in commercial operation and help Miami-Dade County determine the ideal routes for maximizing the fuel-saving potential of its HHVs.

Evaluating performance of MARTe as a real-time framework for feed-back control system at tokamak device

Energy Technology Data Exchange (ETDEWEB)

Yun, Sangwon; Lee, Woongryol; Lee, Taegu; Park, Mikyung; Lee, Sangil [National Fusion Research Institute (NFRI), Gwahangno 169-148, Yuseong-Gu, Daejeon 305-806 (Korea, Republic of); Neto, André C. [Associação EURATOM/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade Técnica de Lisboa, P-1049-001 Lisboa (Portugal); Wallander, Anders [ITER Organization, Route de Vinon sur Verdon, 13115 St Paul Lez Durance (France); Kim, Young-Kuk, E-mail: ykim@cnu.ac.kr [Chungnam National University, Daejeon 305-764 (Korea, Republic of)

2013-10-15

Highlights: •We measured the performance of MARTe by measuring response time and jitter. •We compared the performance of application with and without MARTe. •We compared the performance of MARTe application on different O/Ss. -- Abstract: The Korea Super conducting Tokamak Advanced Research (KSTAR) is performing the task of “Demonstration and Evaluation of ITER CODAC Technologies at KSTAR” whose objective is the evaluation of real-time technologies for decision making on real-time operating systems (RTOS), real-time frameworks and 10 GbE networks. In this task, the Multi-threaded Application Real-Time executor (MARTe) has been evaluated as a real-time framework for real-time feedback control system. The performance of MARTe has been verified by measuring response time and jitter in a path of feedback control from an analog input of a monitoring system to an analog output of an actuator system. In addition, the evaluation has been performed in terms of applicability of MARTe and its performance depending on types of operating system and tuning of CPU affinity and priority. This paper describes the overview of MARTe as a real-time framework, the results of evaluation performance and its implementation.

Evaluating performance of MARTe as a real-time framework for feed-back control system at tokamak device

International Nuclear Information System (INIS)

Yun, Sangwon; Lee, Woongryol; Lee, Taegu; Park, Mikyung; Lee, Sangil; Neto, André C.; Wallander, Anders; Kim, Young-Kuk

2013-01-01

Highlights: •We measured the performance of MARTe by measuring response time and jitter. •We compared the performance of application with and without MARTe. •We compared the performance of MARTe application on different O/Ss. -- Abstract: The Korea Super conducting Tokamak Advanced Research (KSTAR) is performing the task of “Demonstration and Evaluation of ITER CODAC Technologies at KSTAR” whose objective is the evaluation of real-time technologies for decision making on real-time operating systems (RTOS), real-time frameworks and 10 GbE networks. In this task, the Multi-threaded Application Real-Time executor (MARTe) has been evaluated as a real-time framework for real-time feedback control system. The performance of MARTe has been verified by measuring response time and jitter in a path of feedback control from an analog input of a monitoring system to an analog output of an actuator system. In addition, the evaluation has been performed in terms of applicability of MARTe and its performance depending on types of operating system and tuning of CPU affinity and priority. This paper describes the overview of MARTe as a real-time framework, the results of evaluation performance and its implementation

Analysis and evaluation of the applicability of green energy technology

Science.gov (United States)

Xu, Z. J.; Song, Y. K.

2017-11-01

With the seriousness of environmental issues and the shortage of resources, the applicability of green energy technology has been paid more and more attention by scholars in different fields. However, the current researches are often single in perspective and simple in method. According to the Theory of Applicable Technology, this paper analyzes and defines the green energy technology and its applicability from the all-around perspectives of symbiosis of economy, society, environment and science & technology etc., and correspondingly constructs the evaluation index system. The paper further applies the Fuzzy Comprehensive Evaluation to the evaluation of its applicability, discusses in depth the evaluation models and methods, and explains in detail with an example. The author holds that the applicability of green energy technology involves many aspects of economy, society, environment and science & technology and can be evaluated comprehensively by an index system composed of a number of independent indexes. The evaluation is multi-object, multi-factor, multi-level and fuzzy comprehensive, which is undoubtedly correct, effective and feasible by the Fuzzy Comprehensive Evaluation. It is of vital theoretical and practical significance to understand and evaluate comprehensively the applicability of green energy technology for the rational development and utilization of green energy technology and for the better promotion of sustainable development of human and nature.

Designing a performance appraisal system based on balanced scorecard for improving productivity: Case study in Semnan technology and science park

Directory of Open Access Journals (Sweden)

Mohammad Hemati

2012-08-01

Full Text Available Today, organizations for holding and improving their competing merit use performance measurement for evaluation, control, supervision and improvement of their trading processes. Medium and small companies in technology and science parks are very useful in economic revivification and technology development. Technology and science parks have provided necessary consultations, information, suitable equipments, and services for developing technology unites and prepare them for independent presence in industry. One of the necessary elements for the success and improvement of performance in these companies is to establish and implement balanced scorecard, which can be used to reach desired goals, strategies and to improve performance. In this article, we use a structured method for calculating efficiency of four perspectives of balanced scorecard. Statistical society of this research was Semnan technology and Science Park and seven experts are selected for answering questions of the survey. We also complete questionnaire and determine index and relative importance of all indices. For developing strategic goals of Semnan technology and science park according to four perspectives of balanced score card (finance, growth and learning, internal process, six meetings were hold and finally all crisis macro goals index were identified and they were analyzed for evaluating performance.

Technological Innovation Capabilities and Firm Performance

OpenAIRE

Richard C.M. Yam; William Lo; Esther P.Y. Tang; Antonio; K.W. Lau

2010-01-01

Technological innovation capability (TIC) is defined as a comprehensive set of characteristics of a firm that facilities and supports its technological innovation strategies. An audit to evaluate the TICs of a firm may trigger improvement in its future practices. Such an audit can be used by the firm for self assessment or third-party independent assessment to identify problems of its capability status. This paper attempts to develop such an auditing framework that can...

CO2 control technology effects on IGCC plant performance and cost

International Nuclear Information System (INIS)

Chen Chao; Rubin, Edward S.

2009-01-01

As part of the USDOE's Carbon Sequestration Program, an integrated modeling framework has been developed to evaluate the performance and cost of alternative carbon capture and storage (CCS) technologies for fossil-fueled power plants in the context of multi-pollutant control requirements. This paper uses the newly developed model of an integrated gasification combined cycle (IGCC) plant to analyze the effects of adding CCS to an IGCC system employing a GE quench gasifier with water gas shift reactors and a Selexol system for CO 2 capture. Parameters of interest include the effects on plant performance and cost of varying the CO 2 removal efficiency, the quality and cost of coal, and selected other factors affecting overall plant performance and cost. The stochastic simulation capability of the model is also used to illustrate the effect of uncertainties or variability in key process and cost parameters. The potential for advanced oxygen production and gas turbine technologies to reduce the cost and environmental impacts of IGCC with CCS is also analyzed

Technology Games: Using Wittgenstein for Understanding and Evaluating Technology.

Science.gov (United States)

Coeckelbergh, Mark

2017-08-15

In the philosophy of technology after the empirical turn, little attention has been paid to language and its relation to technology. In this programmatic and explorative paper, it is proposed to use the later Wittgenstein, not only to pay more attention to language use in philosophy of technology, but also to rethink technology itself-at least technology in its aspect of tool, technology-in-use. This is done by outlining a working account of Wittgenstein's view of language (as articulated mainly in the Investigations) and by then applying that account to technology-turning around Wittgenstein's metaphor of the toolbox. Using Wittgenstein's concepts of language games and form of life and coining the term 'technology games', the paper proposes and argues for a use-oriented, holistic, transcendental, social, and historical approach to technology which is empirically but also normatively sensitive, and which takes into account implicit knowledge and know-how. It gives examples of interaction with social robots to support the relevance of this project for understanding and evaluating today's technologies, makes comparisons with authors in philosophy of technology such as Winner and Ihde, and sketches the contours of a phenomenology and hermeneutics of technology use that may help us to understand but also to gain a more critical relation to specific uses of concrete technologies in everyday contexts. Ultimately, given the holism argued for, it also promises a more critical relation to the games and forms of life technologies are embedded in-to the ways we do things.

Energy technology evaluation report: Energy security

Science.gov (United States)

Koopman, R.; Lamont, A.; Schock, R.

1992-09-01

Energy security was identified in the National Energy Strategy (NES) as a major issue for the Department of Energy (DOE). As part of a process designed by the DOE to identify technologies important to implementing the NES, an expert working group was convened to consider which technologies can best contribute to reducing the nation's economic vulnerability to future disruptions of world oil supplies, the working definition of energy security. Other working groups were established to deal with economic growth, environmental quality, and technical foundations. Energy Security working group members were chosen to represent as broad a spectrum of energy supply and end-use technologies as possible and were selected for their established reputations as experienced experts with an ability to be objective. The time available for this evaluation was very short. The group evaluated technologies using criteria taken from the NES which can be summarized for energy security as follows: diversifying sources of world oil supply so as to decrease the increasing monopoly status of the Persian Gulf region; reducing the importance of oil use in the US economy to diminish the impact of future disruptions in oil supply; and increasing the preparedness of the US to deal with oil supply disruptions by having alternatives available at a known price. The result of the first phase of the evaluation process was the identification of technology groups determined to be clearly important for reducing US vulnerability to oil supply disruptions. The important technologies were mostly within the high leverage areas of oil and gas supply and transportation demand but also included hydrogen utilization, biomass, diversion resistant nuclear power, and substitute industrial feedstocks.

Cyber security evaluation of II&C technologies

Energy Technology Data Exchange (ETDEWEB)

Thomas, Ken [Idaho National Laboratory (INL), Idaho Falls, ID (United States)

2014-11-01

The Light Water Reactor Sustainability (LWRS) Program is a research and development program sponsored by the Department of Energy, which is conducted in close collaboration with industry to provide the technical foundations for licensing and managing the long-term, safe and economical operation of current nuclear power plants The LWRS Program serves to help the US nuclear industry adopt new technologies and engineering solutions that facilitate the continued safe operation of the plants and extension of the current operating licenses. Within the LWRS Program, the Advanced Instrumentation, Information, and Control (II&C) Systems Technologies Pathway conducts targeted research and development (R&D) to address aging and reliability concerns with the legacy instrumentation and control and related information systems of the U.S. operating light water reactor (LWR) fleet. The II&C Pathway is conducted by Idaho National Laboratory (INL). Cyber security is a common concern among nuclear utilities and other nuclear industry stakeholders regarding the digital technologies that are being developed under this program. This concern extends to the point of calling into question whether these types of technologies could ever be deployed in nuclear plants given the possibility that the information in them can be compromised and the technologies themselves can potentially be exploited to serve as attack vectors for adversaries. To this end, a cyber security evaluation has been conducted of these technologies to determine whether they constitute a threat beyond what the nuclear plants already manage within their regulatory-required cyber security programs. Specifically, the evaluation is based on NEI 08-09, which is the industry’s template for cyber security programs and evaluations, accepted by the Nuclear Regulatory Commission (NRC) as responsive to the requirements of the nuclear power plant cyber security regulation found in 10 CFR 73.54. The evaluation was conducted by a

Performance evaluation of photovoltaic systems on Kuwaiti schools’ rooftop

International Nuclear Information System (INIS)

Al-Otaibi, A.; Al-Qattan, A.; Fairouz, F.; Al-Mulla, A.

2015-01-01

Highlights: • Evaluation of rooftop PV installations at 2 Kuwaiti schools was carried out. • Lack of real plants data in the region and specifically Kuwait motivated the work. • Automated cleaning system allowed for minimization of soiling loss. • The average PV system performance was greater than 76%. • Schools show high potential for rooftop installations. - Abstract: Photovoltaic (PV) is a high-potential renewable energy technology for Kuwait to pursue due to high daily irradiation, and has garnered local attention in recent years due to the growing energy demand and concerns over climate change. As yet, no data are available regarding the actual performance of PV systems in Kuwait’s harsh environment. This paper presents a 12-month-long performance evaluation of the first 85.05 kW p and 21.6 kW p copper indium gallium selenide (CIGS) thin film, grid-connected PV systems on the rooftops of two schools. The schools’ monthly energy consumption and PV generation profiles, the actual performance of the PV plants, the effectiveness of automated cleaning systems on the power output, and the benefits of PV implementation in schools were analyzed and evaluated. Data analysis was applied to filter and normalize the data in order to identify the actual performance parameters. The findings of the study, based on solar irradiation collected, the performance of the module technology and the effectiveness of the automated cleaning systems, show that the performance ratio was maintained between 0.74 and 0.85. Furthermore, the minimum monthly energy yield of the PV systems was about 104 kW h/kW p . The annual average daily final yields of the PV systems in this study were 4.5 kW h/kW p /day. The results provided insight into the performance of CIGS grid-connected PV systems in Kuwait, and those data will be beneficial to the PV research community worldwide. School buildings, particularly for the rooftops, are a unique and important asset for urban PV system

Clean Technology Evaluation & Workforce Development Program

Energy Technology Data Exchange (ETDEWEB)

Patricia Glaza

2012-12-01

The overall objective of the Clean Technology Evaluation portion of the award was to design a process to speed up the identification of new clean energy technologies and match organizations to testing and early adoption partners. The project was successful in identifying new technologies targeted to utilities and utility technology integrators, in developing a process to review and rank the new technologies, and in facilitating new partnerships for technology testing and adoption. The purpose of the Workforce Development portion of the award was to create an education outreach program for middle & high-school students focused on clean technology science and engineering. While originally targeting San Diego, California and Cambridge, Massachusetts, the scope of the program was expanded to include a major clean technology speaking series and expo as part of the USA Science & Engineering Festival on the National Mall in Washington, D.C.

Standoff Detection Technology Evaluation Facility

Data.gov (United States)

Federal Laboratory Consortium — The Standoff Detection Technology Evaluation facility is the only one of its kind in the country and allows researchers to release a known amount of material while...

Development and Evaluation of Science and Technology Education Program Using Interferometric SAR

Science.gov (United States)

Ito, Y.; Ikemitsu, H.; Nango, K.

2016-06-01

This paper proposes a science and technology education program to teach junior high school students to measure terrain changes by using interferometric synthetic aperture radar (SAR). The objectives of the proposed program are to evaluate and use information technology by performing SAR data processing in order to measure ground deformation, and to incorporate an understanding of Earth sciences by analyzing interferometric SAR processing results. To draft the teaching guidance plan for the developed education program, this study considers both science and technology education. The education program was used in a Japanese junior high school. An educational SAR processor developed by the authors and the customized Delft object-oriented radar interferometric software package were employed. Earthquakes as diastrophism events were chosen as practical teaching materials. The selected events indicate clear ground deformation in differential interferograms with high coherence levels. The learners were able to investigate the ground deformations and disasters caused by the events. They interactively used computers and became skilled at recognizing the knowledge and techniques of information technology, and then they evaluated the technology. Based on the results of pre- and post-questionnaire surveys and self-evaluation by the learners, it was clarified that the proposed program was applicable for junior high school education, and the learners recognized the usefulness of Earth observation technology by using interferometric SAR. The usefulness of the teaching materials in the learning activities was also shown through the practical teaching experience.

Performance Evaluation of New Generation CdZnTe Detectors for Safeguards Applications

International Nuclear Information System (INIS)

Ivanovs, V.; Mintcheva, J.; Berlizov, A.; Lebrun, A.

2015-01-01

Cadmium zinc telluride detectors (CdZnTe) have found a wide application in nondestructive assay measurements in the IAEA's verification practice. It is because of their form factor, usability, sensitivity and good spectral characteristics that they are extensively used for fresh and spent fuel attribute test measurements. Until now, the series of CdZnTe detectors utilized in the IAEA have covered the range of 5 mm 3 , 20 mm 3 , 60 mm 3 and 500mm 3 of sensitive volume. Recently, new CdZnTe detectors with improved spectroscopic characteristics and significantly bigger active volume have become available, owing to advances in crystal and detector manufacturing and signal processing technologies. The distinctive feature of this new technological development is the application of a low-intensity monochromatic optical stimulation with infrared (IR) light. The use of IR illumination with a properly chosen wavelength close to the absorption edge of the CdZnTe can significantly improve the performance of the detectors. Recognizing potential benefits of these detectors in safeguards applications, the IAEA has performed an evaluation of their performance characteristics. Under evaluation were several new detectors with sensitive volumes of 500 mm 3 , 1500 mm 3 and 4000 mm 3 , as well as all-in-one 60 mm 3 , 500 mm 3 and 1500 mm 3 integrated micro-spectrometers available from RITEC, Latvia. In addition to the standard performance characteristics, such as energy resolution, peak shape, efficiency, linearity, throughput and temperature stability, the potential use of the detectors for safeguards specific measurements, such as uranium enrichment with infinite thickness method, was of particular interest. The paper will describe the advances in the CdZnTe detector technology and present the results of their performance evaluation. (author)

Evaluation on Performances of Yoghurt Used Modern Technology Versus Natural One

Directory of Open Access Journals (Sweden)

W Sayang Yupardhi

2015-01-01

Full Text Available Abstract. A research for studying performances (aromatics including colour, taste, smell, texture and its financial benefit of milk products i.e. yoghurt which used modern technology versus the natural one was conducted at PT Prima Rasa, Denpasar. The research consisted of two treatments (A = modern technology and B = natural technology. The objective of the research were: 1 to study the differences of aromatic and financial benefit of yoghurt with modern technology versus the natural one, 2 to use as a reference in the future on milk products business, and 3 to increase the quantity and quality of yoghurt and income per capita in the Bali Island. In this research, yoghurt production which used modern technology (treatment A used some ingredients i.e. fresh milk, skimmed milk, starter (imported Lactic Acid Bacteria from Canada and modern equipments i.e. electric incubator for milk fermentation. While the natural technology (treatment B used a slightly different ingredients and equipments i.e. non imported starter and non electric incubator (ampel bamboo. The starter used was lactic acid bacteria naturally found in the ampel bamboo as incubator at once. The incubator was covered with aged banana leaf on the fermentation processes. These ingredients and equipments were very easy to find, available through the year and cheap. There were six replicates in each treatment. Data obtained were analyzed with t test and financial benefit was analyzed descriptively.  Results of the research showed that yoghurt aromatics which used natural technology was 14.29% significantly higher than modern one but its texture was 20.31% or significantly lower. The differences did not seem to cause difference on the taste between them. The average taste score was the same (7.1, indicating that both treatments had the same taste. The financial benefit of the natural yoghurt was much higher (90.74% than that of the modern one (127.40% versus 10.80%.   Key words: yoghurt

Teaching Machines, Programming, Computers, and Instructional Technology: The Roots of Performance Technology.

Science.gov (United States)

Deutsch, William

1992-01-01

Reviews the history of the development of the field of performance technology. Highlights include early teaching machines, instructional technology, learning theory, programed instruction, the systems approach, needs assessment, branching versus linear program formats, programing languages, and computer-assisted instruction. (LRW)

TECHNOLOGY EVALUATION REPORT: TORONTO HARBOUR COMMISSIONERS (THC) SOIL RECYCLE TREATMENT TRAIN. Project Summary

Science.gov (United States)

A demonstration of the Toronto Harbour Commissioners' (THC) Soil Recycle Treatment Train was performed under the Superfund Innovative Technology Evaluation (SITE) Program at a pilot plant facility in Toronto, Ontario, Canada. The Soil Recycle Treatment Train, which consists of s...

Evaluating the Air Quality, Climate Change, and Economic Impacts of Biogas Management Technologies

Science.gov (United States)

This is an abstract for a presentation that describes a project to evaluate economic and environmental performance of several biogas management technologies. It will analyze various criteria air pollutants, greenhouse gas emissions, and costs associated with the use of biogas. Th...

Photovoltaic technology, performance, manufacturing cost and markets

International Nuclear Information System (INIS)

Maycock, P.D.

1999-01-01

A comprehensive discussion of key aspects of photovoltaic energy conversion systems will provide the basis for forecasting PV module shipments from 1999 to 2010. Principal areas covered include: (1) Technology and Performance Status: The module efficiency and performance are described for commercial cell technologies including single crystal silicon, polycrystal silicon, ribbon silicon, film silicon on low cost substrate, amorphous silicon, copper indium diselenide, and cadmium telluride; (2) Manufacturing cost: 1999 costs for PV technologies in production (single crystal silicon, polycrystal silicon, and amorphous silicon) are developed. Manufacturing costs for 10--25 MW plants and 100 MW plants will be estimated; (3) The world PV market is summarized by region, top ten companies, and technology; and (4) Forecast of the World Market (seven market sectors) to 2010 will be presented. Key assumptions, price of modules, incentive programs, price of competing electricity generation will be detailed

Sustainability Of Electricity Supply Technologies Under German Conditions: A Comparative Evaluation

International Nuclear Information System (INIS)

Hirschberg, S.; Dones, R.; Heck, T.; Burgherr, P.; Schenler, W.; Bauer, C.

2005-01-01

The study reported here is intended to provide a framework for a systematic comparative evaluation of the sustainability of energy systems. The existing, representative evaluation criteria and indicators, recently proposed by competent international organisations, have first been reviewed. Based on this survey, and the experience gained at PSI from previous evaluation studies, a set of criteria and indicators for use in the present project have been established. Main efforts have focussed on the generation of quantitative, technology-specific, economic, environmental and social indicators. A number of methods have been employed, including Life Cycle Assessment (LCA), Risk Assessment (RA), and the Impact Pathway Approach (IPA). Some new, advanced methodologies have also been implemented, in particular an improved link between LCA and impact estimation, and an enhanced treatment of site-dependent effects. Two methods of indicator aggregation were employed: namely, the estimation of total (internal and external) costs, and Multi-Criteria Decision Analysis (MCDA). Use of MCDA is motivated principally by the acknowledgement of the role of value judgments in decision-making. In terms of total costs, nuclear power displays top performance under German conditions, superior to all other currently implemented technologies. Evaluations employing a variety of sustainability criteria result in a fragmented picture of the merits and drawbacks of the currently available electricity supply options. No single system exhibits superior performance on the basis of all criteria. MCDA ranking based on the three pillars of sustainability of economy, ecology and social, is relatively robust if the pillars are considered to be equally important, and the weighting of lower-level criteria (e.g. financial requirements or employment effects) is subject to variation. Placing emphasis on economy penalizes renewables, while emphasis on the environment penalizes fossil systems, and emphasis on

Sustainability Of Electricity Supply Technologies Under German Conditions: A Comparative Evaluation

Energy Technology Data Exchange (ETDEWEB)

Hirschberg, S.; Dones, R.; Heck, T.; Burgherr, P.; Schenler, W.; Bauer, C

2005-03-01

The study reported here is intended to provide a framework for a systematic comparative evaluation of the sustainability of energy systems. The existing, representative evaluation criteria and indicators, recently proposed by competent international organisations, have first been reviewed. Based on this survey, and the experience gained at PSI from previous evaluation studies, a set of criteria and indicators for use in the present project have been established. Main efforts have focussed on the generation of quantitative, technology-specific, economic, environmental and social indicators. A number of methods have been employed, including Life Cycle Assessment (LCA), Risk Assessment (RA), and the Impact Pathway Approach (IPA). Some new, advanced methodologies have also been implemented, in particular an improved link between LCA and impact estimation, and an enhanced treatment of site-dependent effects. Two methods of indicator aggregation were employed: namely, the estimation of total (internal and external) costs, and Multi-Criteria Decision Analysis (MCDA). Use of MCDA is motivated principally by the acknowledgement of the role of value judgments in decision-making. In terms of total costs, nuclear power displays top performance under German conditions, superior to all other currently implemented technologies. Evaluations employing a variety of sustainability criteria result in a fragmented picture of the merits and drawbacks of the currently available electricity supply options. No single system exhibits superior performance on the basis of all criteria. MCDA ranking based on the three pillars of sustainability of economy, ecology and social, is relatively robust if the pillars are considered to be equally important, and the weighting of lower-level criteria (e.g. financial requirements or employment effects) is subject to variation. Placing emphasis on economy penalizes renewables, while emphasis on the environment penalizes fossil systems, and emphasis on

Evaluation of Coating Removal and Aggressive Surface Removal Surface Technologies Applied to Concrete Walls, Brick Walls, and Concrete Ceilings

Energy Technology Data Exchange (ETDEWEB)

Lagos, L.E.; Ebadian, M.A.

1997-11-01

The purpose of this investigation was to test and evaluate innovative and commercially available technologies for the surface decontamination of walls and ceilings. This investigation supports the DOE's objectives of reducing risks to human health and the environment through its restoration projects at FEMP and MEMP. This project was performed at the Hemispheric Center for Environmental Technology (HCET) at Florida International University (FIU), where one innovative and four commercially available decontamination technologies were evaluated under standard, non-nuclear testing conditions. The performance data generated by this project will assist DOE site managers in the selection of the safest, most efficient, and most cost-effective decontamination technologies to accomplish their remediation objectives.

Energy technologies for distributed utility applications: Cost and performance trends, and implications for photovoltaics

International Nuclear Information System (INIS)

Eyer, J.M.

1994-01-01

Utilities are evaluating several electric generation and storage (G ampersand S) technologies for distributed utility (DU) applications. Attributes of leading DU technologies and implications for photovoltaics (PV) are described. Included is a survey of present and projected cost and performance for: (1) small, advanced combustion turbines (CTs); (2) advanced, natural gas-fired, diesel engines (diesel engines); and (3) advanced lead-acid battery systems (batteries). Technology drivers and relative qualitative benefits are described. A levelized energy cost-based cost target for PV for DU applications is provided. The analysis addresses only relative cost, for PV and for three selected alternative DU technologies. Comparable size, utility, and benefits are assumed, although relative value is application-specific and often technology- and site-specific

Assistive technology evaluations: Remote-microphone technology for children with Autism Spectrum Disorder.

Science.gov (United States)

Schafer, Erin C; Wright, Suzanne; Anderson, Christine; Jones, Jessalyn; Pitts, Katie; Bryant, Danielle; Watson, Melissa; Box, Jerrica; Neve, Melissa; Mathews, Lauren; Reed, Mary Pat

The goal of this study was to conduct assistive technology evaluations on 12 children diagnosed with Autism Spectrum Disorder (ASD) to evaluate the potential benefits of remote-microphone (RM) technology. A single group, within-subjects design was utilized to explore individual and group data from functional questionnaires and behavioral test measures administered, designed to assess school- and home-based listening abilities, once with and once without RM technology. Because some of the children were unable to complete the behavioral test measures, particular focus was given to the functional questionnaires completed by primary teachers, participants, and parents. Behavioral test measures with and without the RM technology included speech recognition in noise, auditory comprehension, and acceptable noise levels. The individual and group teacher (n=8-9), parent (n=8-9), and participant (n=9) questionnaire ratings revealed substantially less listening difficulty when RM technology was used compared to the no-device ratings. On the behavioral measures, individual data revealed varied findings, which will be discussed in detail in the results section. However, on average, the use of the RM technology resulted in improvements in speech recognition in noise (4.6dB improvement) in eight children, higher auditory working memory and comprehension scores (12-13 point improvement) in seven children, and acceptance of poorer signal-to-noise ratios (8.6dB improvement) in five children. The individual and group data from this study suggest that RM technology may improve auditory function in children with ASD in the classroom, at home, and in social situations. However, variability in the data and the inability of some children to complete the behavioral measures indicates that individualized assistive technology evaluations including functional questionnaires will be necessary to determine if the RM technology will be of benefit to a particular child who has ASD. Copyright �

Performance Criteria for Capture and/or Immobilization Technologies

Energy Technology Data Exchange (ETDEWEB)

Jubin, R. T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bruffey, S. H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Strachan, D. M. [Strata-G, LLC, Knoxville, TN (United States); Soelberg, N. R. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Spencer, B. B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Riley, B. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-02-01

The capture and subsequent immobilization of the four volatile radionuclides (³H, ¹⁴C, ⁸⁵Kr, and ¹²⁹I) from the off-gas streams of a used nuclear fuel reprocessing facility has been a topic of substantial research interest for the US DOE and international colleagues. Regulations set forth by the US EPA direct that some or all of these radionuclides (based upon fuel burnup, fuel type, cooling time, etc.) will require removal, to some extent, from the plant effluent streams prior to discharge to the environment. Upon removal, the radionuclide, as well as any associated sorbent, is destined for waste. Research of separation and capture methodologies has included a wide range of technologies including liquid caustic scrubbing systems, solid adsorbents, and cryogenic distillation. The studies of waste forms have been correspondingly diverse. In considering the technologies available for future development and implementation of both sorbents and waste forms, it will be necessary to use benchmarked measures of performance to objectively evaluate each sorbent system or waste form. This document is intended to provide initial guidance on the types of performance criteria for capture materials and waste forms intended for use in the recycling removal and disposal of UNF and, where possible, the minimum acceptable values for those criteria.

Three-dimensional simulations in optimal performance trial between two types of Hall sensors fabrication technologies

Energy Technology Data Exchange (ETDEWEB)

Paun, Maria-Alexandra, E-mail: map65@cam.ac.uk

2015-10-01

The main objective of the present work is to make a comparison between Hall devices integrated in regular bulk and Silicon-on-Insulator (SOI) CMOS technology. A three-dimensional model based on numerical estimation is provided for a particular XL Hall structure in two different technologies (the first one is XFAB XH 0.35 µm regular bulk CMOS and the second one is XFAB SOI XI10 1 µm non-fully depleted). In assessing the performance of the Hall Effect sensors included in the comparison, both three-dimensional physical simulations and measurements results will be used. In order to discriminate which category of sensors has the highest performance, their main characteristic parameters, including input resistance, Hall voltage, absolute sensitivity and their temperature drift, will be extracted and compared. Electrostatic potential and current density distribution are important aspects that are also investigated. The particular technology offering the highest sensor performance is identified. - Highlights: • A comparison between Hall devices integrated in regular bulk and SOI CMOS technologies is made. • A three-dimensional model for the XL Hall structure, in the two technologies, is provided. • The main characteristic parameters and the temperature drift are investigated. • The sensors performance is evaluated using 3D physical simulations and measurements data.

Performance Analyses in an Assistive Technology Service Delivery Process

DEFF Research Database (Denmark)

Petersen, Anne Karin

Performance Analyses in an Assistive Technology Service Delivery Process.Keywords: process model, occupational performance, assistive technologiesThe Poster is about teaching students, using models and theory in education and practice. It is related to Occupational therapy process and professional...... af top-til-bund, klientcentreret og aktivitetsbaseret interventioner, ERGO/MunksgaardFisher, A. &, Griswold, L. A., 2014. Performance Skills. I: B.Schell red.2014 Occupational Therapy. Willard &Spackman’s occupational therapy. -12th ed., p.249-264Cook A.M., Polgar J.M. (2015) Assistive Technologies...

Cloud service performance evaluation: status, challenges, and opportunities – a survey from the system modeling perspective

Directory of Open Access Journals (Sweden)

Qiang Duan

2017-05-01

Full Text Available With rapid advancement of Cloud computing and networking technologies, a wide spectrum of Cloud services have been developed by various providers and utilized by numerous organizations as indispensable ingredients of their information systems. Cloud service performance has a significant impact on performance of the future information infrastructure. Thorough evaluation on Cloud service performance is crucial and beneficial to both service providers and consumers; thus forming an active research area. Some key technologies for Cloud computing, such as virtualization and the Service-Oriented Architecture (SOA, bring in special challenges to service performance evaluation. A tremendous amount of effort has been put by the research community to address these challenges and exciting progress has been made. Among the work on Cloud performance analysis, evaluation approaches developed with a system modeling perspective play an important role. However, related works have been reported in different sections of the literature; thus lacking a big picture that shows the latest status of this area. The objectives of this article is to present a survey that reflects the state of the art of Cloud service performance evaluation from the system modeling perspective. This articles also examines open issues and challenges to the surveyed evaluation approaches and identifies possible opportunities for future research in this important field.

Report of the evaluation by the Ad Hoc Review Committee on Information Technology. In-advance evaluation in fiscal year 2000

International Nuclear Information System (INIS)

2001-06-01

The Research Evaluation Committee, which consisted of 14 members from outside of the Japan Atomic Energy Research Institute (JAERI), set up an Ad Hoc Review Committee on Information Technology in accordance with the Fundamental Guideline for the Evaluation of Research and Development (R and D) at JAERI' and its subsidiary regulations in order to evaluate the adequacy of the R and D programs pertaining to the establishment and utilization of the Information Technology Based Laboratory (ITBL) to be implemented for five years starting in Fiscal Year 2001 at Center for Promotion of Computational Science and Engineering and Department of Environmental Sciences of JAERI. The Ad Hoc Review Committee consisted of eight specialists from outside of JAERI. The Ad Hoc Review Committee conducted its activities from February to March 2001. The evaluation was performed on the basis of the materials submitted in advance and of the oral presentations made at the Ad Hoc Review Committee meeting which was held on February 9, 2001, in line with the items, viewpoints, and criteria for the evaluation specified by the Research Evaluation Committee. The result of the evaluation by the Ad Hoc Review Committee was submitted to the Research Evaluation Committee, and was judged to be appropriate at its meeting held on March 16, 2001. This report describes the result of the evaluation by the Ad Hoc Review Committee on Information Technology. (author)

Making use of research: clinical views on an evaluation of everyday technology use.

Science.gov (United States)

Nygård, Louise; Kottorp, Anders; Rosenberg, Lena

2015-01-01

The study aim was to investigate how and when an evaluation of perceived difficulty in use of everyday technology (Everyday Technology Use Questionnaire, ETUQ) could be used in clinical occupational therapy. Eight focus-group interviews were undertaken with a total of 42 participants (occupational therapists), and data were analysed with a constant comparative approach. The findings are presented in four main categories, including (i) appropriate purposes and contexts for using ETUQ, (ii) standardization versus individual flexibility, (iii) approaching everyday technology use and occupation as one whole, and (iv) synthesizing and documentation. In conclusion, the participants considered ability to use technology to be an important topic for occupational therapy, particularly in investigations of clients with subtle disabilities and in connection with discharge from hospital - but not in inpatient care. They had different views on how to integrate ETUQ with evaluations of occupational performance, and new ideas on how information about clients' ability to use technology could be utilized in interventions. They held standardized evaluations in high regard, but a paradox appeared in that many of them would use ETUQ in a non-standardized way, while simultaneously asking for a standardized output to be used in clients' medical files and to guide interventions.

ECONOMIC EVALUATION OF CO2 SEQUESTRATION TECHNOLOGIES TASK 4, BIOMASS GASIFICATION-BASED PROCESSING

Energy Technology Data Exchange (ETDEWEB)

Martha L. Rollins; Les Reardon; David Nichols; Patrick Lee; Millicent Moore; Mike Crim; Robert Luttrell; Evan Hughes

2002-06-01

Biomass derived energy currently accounts for about 3 quads of total primary energy use in the United States. Of this amount, about 0.8 quads are used for power generation. Several biomass energy production technologies exist today which contribute to this energy mix. Biomass combustion technologies have been the dominant source of biomass energy production, both historically and during the past two decades of expansion of modern biomass energy in the U. S. and Europe. As a research and development activity, biomass gasification has usually been the major emphasis as a method of more efficiently utilizing the energy potential of biomass, particularly wood. Numerous biomass gasification technologies exist today in various stages of development. Some are simple systems, while others employ a high degree of integration for maximum energy utilization. The purpose of this study is to conduct a technical and economic comparison of up to three biomass gasification technologies, including the carbon dioxide emissions reduction potential of each. To accomplish this, a literature search was first conducted to determine which technologies were most promising based on a specific set of criteria. The technical and economic performances of the selected processes were evaluated using computer models and available literature. Using these results, the carbon sequestration potential of the three technologies was then evaluated. The results of these evaluations are given in this final report.

Aging evaluation of active components by using performance evaluation

International Nuclear Information System (INIS)

Jung, S. K.; Jin, T. E.; Kim, J. S.; Jung, I. S.; Kim, T. R.

2003-01-01

Risk analysis and performance evaluation methodology were applied to the aging evaluation of active components in the periodic safety review of Wolsung unit 1. We conclude that evaluation of performance is more effective to discriminate the aging degradation of active component than the evaluation of aging mechanism. It is essential to analyze the common cause failures of low performance components to evaluate the properness of present maintenance system. Past 10 years failure history is used for establishing the performance criteria. Past 2 years failure history is used for the evaluating the recent performance condition. We analyze the failure mode of the components to improve the maintenance system. Performance evaluation methodology is useful for the quantitative evaluation of aging degradation of active components. Analysis on the repeated failures can be useful for the feedback to maintenance plan and interval

The value of adding regional to local stakeholder involvement in evaluating the acceptability of innovative technologies

International Nuclear Information System (INIS)

Peterson, T.S.; McCabe, G.; Niesen, K.; Serie, P.

1995-02-01

Technology is urgently needed to clean up contamination by volatile organic compounds at United States Department of Energy (DOE) sites. In many cases, however, existing technology is too slow, inefficient, or expensive. The record of technology development is, in some cases, similarly disappointing. Remediation technologies developed at great expense and evaluated piecemeal over long periods have not been deployed because, in the end, the public judged them ineffective or unacceptable. The need for successful methods of remediation is too great and resources too limited to continue with ineffective technology evaluation. In order to make good decisions about which technologies to deploy, remedial project managers need to know stakeholders' requirements for the performance of proposed technologies. Expanding stakeholder involvement regionally identifies the concerns of a broad range of stakeholders at and DOE sites throughout the West -- issues that must be taken into account if technologies are to be accepted for wide deployment

H Scan/AHP advanced technology proposal evaluation process

Energy Technology Data Exchange (ETDEWEB)

Mack, S. [Energetics, Inc., Columbia, MD (United States); Valladares, M.R.S. de [National Renewable Energy Lab., Washington, DC (United States)

1996-10-01

It is anticipated that a family of high value/impact projects will be funded by the Hydrogen Program to field test hydrogen technologies that are at advanced stages of development. These projects will add substantial value to the Program in several ways, by: demonstrating successful integration of multiple advanced technologies, providing critical insight on issues of larger scale equipment design, construction and operations management, yielding cost and performance data for competitive analysis, refining and deploying enhanced safety measures. These projects will be selected through a competitive proposal evaluation process. Because of the significant scope and funding levels of projects at these development phases, Program management has indicated the need for an augmented proposal evaluation strategy to ensure that supported projects are implemented by capable investigative teams and that their successful completion will optimally advance programmatic objectives. These objectives comprise a complex set of both quantitative and qualitative factors, many of which can only be estimated using expert judgment and opinion. To meet the above need, the National Renewable Energy Laboratory (NREL) and Energetics Inc. have jointly developed a proposal evaluation methodology called H Scan/AHP. The H Scan component of the process was developed by NREL. It is a two-part survey instrument that substantially augments the type and scope of information collected in a traditional proposal package. The AHP (Analytic Hierarchy Process) component was developed by Energetics. The AHP is an established decision support methodology that allows the Program decision makers to evaluate proposals relatively based on a unique set of weighted criteria that they have determined.

New Technologies, New Approaches to Evaluating Academic Productivity

Science.gov (United States)

Rich, Peter J.; West, Richard E.

2012-01-01

Technology has enabled a proliferation of publication venues for disseminating academic work. The task of evaluating the relative quality of each of these venues is simultaneously exacerbated and resolved by the use of new technologies. In this article, the authors propose a three-pronged framework for evaluating the quality of scholarly work that…

Health technology assessment. Evaluation of biomedical innovative technologies.

Science.gov (United States)

Turchetti, Giuseppe; Spadoni, Enza; Geisler, Eliezer Elie

2010-01-01

This article describes health technology assessment (HTA) as an evaluation tool that applies systematic methods of inquiry to the generation and use of health technologies and new products. The focus of this article is on the contributions of HTA to the management of the new product development effort in the biomedical organization. Critical success factors (CSFs) are listed, and their role in assessing success is defined and explained. One of the conclusions of this article is that HTA is a powerful tool for managers in the biomedical sector, allowing them to better manage their innovation effort in their continuing struggle for competitiveness and survival.

A proposed framework for establishing integrated cost and performance criteria for environmental technologies. A summary report to the U.S. Department of Energy

International Nuclear Information System (INIS)

1994-05-01

Through an Interagency Agreement between the US Environmental Protection Agency (EPA) and the US Department of Energy (DOE), EPA directed a project to establish a suite of standard cost and performance criteria to guide the evaluation of environmental cleanup technologies for DOE sites. Ideally, these criteria would be ''generic'' in that they could be used as a basis for evaluating any cleanup technology for any DOE site. To be most useful, however, these criteria would also reflect the interests of diverse decisionmakers who influence DOE technology evaluation. The project was conducted by the National Environmental Technology Applications Center (NETAC), a nonprofit organization specializing in the development and commercialization of new and innovative environmental technologies for national and international markets. To accomplish the project objective, NETAC (1) developed a data gathering questionnaire, (2) interviewed government and industry decisionmakers, (3) identified previous criteria development efforts, (4) conducted a workshop, (5) evaluated workshop discussions, and (6) applied its five years' experience in commercializing environmental technologies to analyze project findings. The project resulted in the development of a unique and comprehensive resource or tool to enhance communication among decisionmakers. This resource, a ''Proposed Framework for Establishing Integrated Cost and Performance Criteria for Evaluating Environmental Cleanup Technologies for DOE Sites,'' offers decisionmakers a first-time comprehensive assessment of major technology evaluation issues by a decisionmaker group

Evaluation of Extended-Wear Hearing Technology for Children with Hearing Loss.

Science.gov (United States)

Wolfe, Jace; Schafer, Erin; Martella, Natalie; Morais, Mila; Mann, Misty

2015-01-01

Research shows that many older children and teenagers who have mild to moderately severe sensorineural hearing loss do not use their hearing instruments during all waking hours. A variety of reasons may contribute toward this problem, including concerns about cosmetics associated with hearing aid use and the inconvenience of daily maintenance associated with hearing instruments. Extended-wear hearing instruments are inserted into the wearer's ear canal by an audiologist and are essentially invisible to outside observers. The goal of this study was to evaluate the potential benefits and limitations associated with use of extended-wear hearing instruments in a group of children with hearing loss. A two-way repeated measures design was used to examine performance differences obtained with the participants' daily-wear hearing instruments versus that obtained with extended-wear hearing instruments. Sixteen children, ages 10-17 yr old, with sensorineural hearing loss ranging from mild to moderately severe. Probe microphone measures were completed to evaluate the aided output of device. Behavioral test measures included word recognition in quiet, sentence recognition in noise, aided warble-tone thresholds, and psychophysical loudness scaling. Questionnaires were also administered to evaluate subjective performance with each hearing technology. Data logging suggested that many participants were not using their daily-wear hearing instruments during all waking hours (mean use was less than 6 h/day). Real ear probe microphone measurements indicated that a closer fit to the Desired Sensation Level Version 5 prescriptive targets was achieved with the children's daily-wear instruments when compared to the extended-wear instruments. There was no statistically significant difference in monosyllabic word recognition at 50 or 60 dBA obtained with the two hearing technologies. Sentence recognition in noise obtained with use of the extended-wear devices was, however, significantly

Performance monitoring of different module technologies and design configurations of PV systems in South Africa

CSIR Research Space (South Africa)

Serameng, T

2016-06-01

Full Text Available Africa. The goal of this work was to analyse and report on the performance of PV systems by evaluating the energy output of various PV system configurations and module technologies in the South African (southern hemisphere) climatic conditions. To achieve...

Performance and Complexity Evaluation of Iterative Receiver for Coded MIMO-OFDM Systems

Directory of Open Access Journals (Sweden)

Rida El Chall

2016-01-01

Full Text Available Multiple-input multiple-output (MIMO technology in combination with channel coding technique is a promising solution for reliable high data rate transmission in future wireless communication systems. However, these technologies pose significant challenges for the design of an iterative receiver. In this paper, an efficient receiver combining soft-input soft-output (SISO detection based on low-complexity K-Best (LC-K-Best decoder with various forward error correction codes, namely, LTE turbo decoder and LDPC decoder, is investigated. We first investigate the convergence behaviors of the iterative MIMO receivers to determine the required inner and outer iterations. Consequently, the performance of LC-K-Best based receiver is evaluated in various LTE channel environments and compared with other MIMO detection schemes. Moreover, the computational complexity of the iterative receiver with different channel coding techniques is evaluated and compared with different modulation orders and coding rates. Simulation results show that LC-K-Best based receiver achieves satisfactory performance-complexity trade-offs.

REMEDIATION TECHNOLOGY EVALUATION AT THE GILT EDGE MINE, SOUTH DAKOTA

Science.gov (United States)

This document reports the findings of the Mine Waste Technology Program's Activity III, Project 29,The Remediation Technology Evaluation Project at the Gilt Edge Mine, S.D. This project consisted of evaluating three emerging acidic waste rock stabilization technologies and compar...

Performance evaluation of domestic prototype dose area product meter SFT-1

International Nuclear Information System (INIS)

Lee, Ho Sun; Han, Seong Gyu; Roh, Young Roh; Lim, Hyun Jong; Kim, Jung Min; Kim, Jong Uk; Chae, Hyun Sik; Yoon, Yong Su

2016-01-01

The importance of radiation dose display of medical X-ray equipment was emphasized, while third edition of IEC(International Electrotechnical Commission) 60601 started to apply. The existing medical X-ray equipment selected a method for attaching the DAP(Dose Area Product) meter when the dose display. However, because the DAP meter was dependent on all of the income, And it did not yet produced in Korea. So, we received the support of Seoul R and BD Program(Grants No. C1152055) to produce DAP meter prototype of the Domestically technology. In this study, the performance of this prototype was evaluated by comparing the German company's product. Evaluation item was an electronic capture performance, radiation dose dependence, radiation quality dependence, energy transmittance, repeatability, light transmittance of 6 entries. And IEC 60580 was based on this evaluation. Evaluation results were electronic capture performance intrinsic error 9.5%, radiation dose dependence limits of variation 1%, repeatabilit y coefficient of variation 2%, energy transmittance 91% each assessment was passed. However radiation quality dependence limits of variation 29%, light transmittance 55% was less than acceptance criteria

A proposed framework for establishing integrated cost and performance criteria for environmental technologies: A summary report

International Nuclear Information System (INIS)

1994-05-01

This document presents a summary of results of a joint EPA/DOE project aimed at establishing a suite of standard cost and performance criteria for evaluating environmental cleanup technologies for DOE sites. Project findings include: (1) decisionmakers have quite different perspectives with interests and information needs varying among decisionmaker groups, (2) previous criteria development efforts may be too narrowly focused to apply to all decisionmakers, (3) criteria must include social/political/economic interests of decisionmakers as well as site-specific variations, and (4) there are 5 core questions that all decisionmakers are likely to ask when considering a technology for use at a site. The resource developed in the project offers decisionmakers a first-time comprehensive assessment of major technology evaluation issues

Multijunction Photovoltaic Technologies for High-Performance Concentrators: Preprint

Energy Technology Data Exchange (ETDEWEB)

McConnell, R.; Symko-Davies, M.

2006-05-01

Multijunction solar cells provide high-performance technology pathways leading to potentially low-cost electricity generated from concentrated sunlight. The National Center for Photovoltaics at the National Renewable Energy Laboratory has funded different III-V multijunction solar cell technologies and various solar concentration approaches. Within this group of projects, III-V solar cell efficiencies of 41% are close at hand and will likely be reported in these conference proceedings. Companies with well-developed solar concentrator structures foresee installed system costs of $3/watt--half of today's costs--within the next 2 to 5 years as these high-efficiency photovoltaic technologies are incorporated into their concentrator photovoltaic systems. These technology improvements are timely as new large-scale multi-megawatt markets, appropriate for high performance PV concentrators, open around the world.

Advanced fuel technology and performance: Current status and trends

International Nuclear Information System (INIS)

1990-11-01

During the last years the Nuclear Fuel Cycle and Waste Management Division of the IAEA has been giving great attention to the collection, analysis and exchange of information in the field of reactor fuel technology. Most of these activities are being conducted in the framework of the International Working Group on Water Reactor Fuel Performance and Technology (IWGFPT). The purpose of this Advisory Group Meeting on Advanced Fuel Technology and Performance was to update and to continue the previous work, and to review the experience of advanced fuel technology, its performance with regard to all types of reactors and to outline the future trends on the basis of national experience and discussions during the meeting. As a result of the meeting a Summary Report was prepared which reflected the status of the advanced nuclear fuel technology up to 1990. The 10 papers presented by participants of this meeting are also published here. A separate abstract was prepared for each of these papers. Refs, figs and tabs

Experimental Facilities for Performance Evaluation of Fast Reactor Components

International Nuclear Information System (INIS)

Chandramouli, S.; Kumar, V.A. Suresh; Shanmugavel, M.; Vijayakumar, G.; Vinod, V.; Noushad, I.B.; Babu, B.; Kumar, G. Padma; Nashine, B.K.; Rajan, K.K.

2013-01-01

Brief details about various experimental facilities catering to the testing and performance evaluation requirements of fast reactor components have been brought out. These facilities have been found to be immensely useful to continue research and development activities in the areas of component development and testing, sodium technology, thermal hydraulics and sodium instrumentation for the SFR’s. In addition new facilities which have been planned will be of great importance for the developmental activities related to future SFR’s

Threshold evaluations of industrial conservation technologies run in ISTUM base case

Energy Technology Data Exchange (ETDEWEB)

1978-12-20

The results of threshold evaluations performed on several INDUS technologies which were competed with other new and conventional industrial technologies in the Industrial Sector Technology Use Model (ISTUM) developed by EEA are summarized. The ISTUM model is briefly described and includes the input technology categories and service sectors treated in the model, and the solution technique used. The input data specifications are summaried for the Industry Conservation Technologies run in the ISTUM base case. Included are listings of the technologies run in ISTUM, those not run in ISTUM, and a discussion of the absence of a retrofit algorithm in ISTUM and its resulting impact on conservation technologies. Also included is a discussion of the capital cost variability, maximum market fraction, size and load factors and data quality specifications for the conservation technologies in ISTUM. The results of the ISTUM base case run are presented, describing the important limitations and constraints of the base case run, the key assumptions inherent in the base case, and the summarized results of energy savings by year for different generic technology types. The technology characterization data developed for each INDUS technology run in the ISTUM base case are discussed in detail. The descriptions include the calculations and assumptions used in determining the service demand displacement, equipment cost, maximum market fraction, data quality, and size and load range for each technology.

Performance Evaluation of Java Based Object Relational Mapping Tools

Directory of Open Access Journals (Sweden)

Shoaib Mahmood Bhatti

2013-04-01

Full Text Available Object persistency is the hot issue in the form of ORM (Object Relational Mapping tools in industry as developers use these tools during software development. This paper presents the performance evaluation of Java based ORM tools. For this purpose, Hibernate, Ebean and TopLinkhave been selected as the ORM tools which are popular and open source. Their performance has been measured from execution point of view. The results show that ORM tools are the good option for the developers considering the system throughput in shorter setbacks and they can be used efficiently and effectively for performing mapping of the objects into the relational dominated world of database, thus creating a hope for a better and well dominated future of this technology.

Review and evaluation of technology, equipment, codes and standards for digitization of industrial radiographic film

International Nuclear Information System (INIS)

1992-05-01

This reports contains a review and evaluation of the technology, equipment, and codes and standards related to the digitization of industrial radiographic film. The report presents recommendations and equipment-performance specifications that will allow the digitization of radiographic film from nuclear power plant components in order to produce faithful reproductions of flaw images of interest on the films. Justification for the specifications selected are provided. Performance demonstration tests for the digitization process are required and criteria for such tests is presented. Also several comments related to implementation of the technology are presented and discussed

Electrical testing and performance evaluation of 1:1 prototype JET ELM control coils

Energy Technology Data Exchange (ETDEWEB)

Kanabar, Deven, E-mail: deven@ipr.res.in; Roy, Swati; Ghate, Mahesh; Raj, Piyush; Kundu, Ananya; Kumar, Nitish; Bhavsar, Dhaval; Panchal, Arun; Pradhan, Subrata, E-mail: pradhan@ipr.res.in

2016-12-15

Highlights: • An appropriate 1:1 prototype Small and Large ELM coils for JET have been successfully manufactured using indigenous technologies. • ELM coils have been tested extensively to verify and validated their performance with respect to operational requirement of JET. • The test results confirm and validate the electrical performance of ELM coils. - Abstract: Magnet Technology Development Division at Institute for Plasma research is engaged in extensive R & D for appropriate technologies towards manufacturing of Edge Localized Mode (ELM) magnets for Large Tokamak such as Joint European Torus (JET) as well as for Steady State Superconducting Tokamak (SST-1). Under this project, manufacturing of 1:1 prototype of Large and Small JET ELM control coils (CC) is completed incorporating indigenously developed manufacturing and insulation technologies. Performance evaluation of both the types of coil has been completed for its current carrying capability and insulation resistance as required by various operational scenarios of JET. Experimental setups, test procedures and measurements for electrical characterization of both type of ELM control coil has been discussed in this paper.

Electrical testing and performance evaluation of 1:1 prototype JET ELM control coils

International Nuclear Information System (INIS)

Kanabar, Deven; Roy, Swati; Ghate, Mahesh; Raj, Piyush; Kundu, Ananya; Kumar, Nitish; Bhavsar, Dhaval; Panchal, Arun; Pradhan, Subrata

2016-01-01

Highlights: • An appropriate 1:1 prototype Small and Large ELM coils for JET have been successfully manufactured using indigenous technologies. • ELM coils have been tested extensively to verify and validated their performance with respect to operational requirement of JET. • The test results confirm and validate the electrical performance of ELM coils. - Abstract: Magnet Technology Development Division at Institute for Plasma research is engaged in extensive R & D for appropriate technologies towards manufacturing of Edge Localized Mode (ELM) magnets for Large Tokamak such as Joint European Torus (JET) as well as for Steady State Superconducting Tokamak (SST-1). Under this project, manufacturing of 1:1 prototype of Large and Small JET ELM control coils (CC) is completed incorporating indigenously developed manufacturing and insulation technologies. Performance evaluation of both the types of coil has been completed for its current carrying capability and insulation resistance as required by various operational scenarios of JET. Experimental setups, test procedures and measurements for electrical characterization of both type of ELM control coil has been discussed in this paper.

Teaching Technology: From Knowing to Feeling Enhancing Emotional and Content Acquisition Performance through Gardner's Multiple Intelligences Theory in Technology and Design Lessons

Science.gov (United States)

Sanchez-Martin, Jesus; Alvarez-Gragera, Garcia J.; Davila-Acedo, Maria Antonia; Mellado, Vicente

2017-01-01

Gardner's Multiple Intelligences Theory (MIT) can be a cognitive and emotional improvement if is taken into account in the standard development of the Technology lessons. This work presents a preliminary evaluation of the performance enhancement in two concomitant aspects: contents acquisition and emotional yield. The study was made on up to 150…

Evaluation of safety, performance and emissions of synthetic fuel blends in a Cessna Citation II

NARCIS (Netherlands)

Snijders, T.A.; Melkert, J.A.

2011-01-01

Prior to being used in aviation, alternative fuels have to be tested thoroughly to ensure safe operation. At Delft University of Technology, a test programme was performed to evaluate the safety, performance and emissions of synthetic fuel blends. During test preparations, compatibility of the

Technology Leadership in Malaysia's High Performance School

Science.gov (United States)

Yieng, Wong Ai; Daud, Khadijah Binti

2017-01-01

Headmaster as leader of the school also plays a role as a technology leader. This applies to the high performance schools (HPS) headmaster as well. The HPS excel in all aspects of education. In this study, researcher is interested in examining the role of the headmaster as a technology leader through interviews with three headmasters of high…

48 CFR 436.604 - Performance evaluation.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Performance evaluation... Performance evaluation. Preparation of performance evaluation reports. (a) In addition to the requirements of FAR 36.604, performance evaluation reports shall be prepared for indefinite-delivery type contracts...

Fed-batch bioreactor performance and cell line stability evaluation of the artificial chromosome expression technology expressing an IgG1 in Chinese hamster ovary cells.

Science.gov (United States)

Combs, Rodney G; Yu, Erwin; Roe, Susanna; Piatchek, Michele Bailey; Jones, Heather L; Mott, John; Kennard, Malcolm L; Goosney, Danika L; Monteith, Diane

2011-01-01

The artificial chromosome expression (ACE) technology system uses an engineered artificial chromosome containing multiple site-specific recombination acceptor sites for the rapid and efficient construction of stable cell lines. The construction of Chinese hamster ovary(CHO) cell lines expressing an IgG1 monoclonal antibody (MAb) using the ACE system has been previously described (Kennard et al., Biotechnol Bioeng. 2009;104:540-553). To further demonstrate the manufacturing feasibility of the ACE system, four CHO cell lines expressing the human IgG1 MAb 4A1 were evaluated in batch and fed-batch shake flasks and in a 2-L fed-batch bioreactor. The batch shake flasks achieved titers between 0.7 and 1.1 g/L, whereas the fed-batch shake flask process improved titers to 2.5–3.0 g/L. The lead 4A1 ACE cell line achieved titers of 4.0 g/L with an average specific productivity of 40 pg/(cell day) when cultured in a non optimized 2-L fed-batch bioreactor using a completely chemically defined process. Generational stability characterization of the lead 4A1-expressing cell line demonstrated that the cell line was stable for up to 75 days in culture. Product quality attributes of the 4A1 MAb produced by the ACE system during the stability evaluation period were unchanged and also comparable to existing expression technologies such as the CHO-dhfr system. The results of this evaluation demonstrate that a clonal, stable MAb-expressing CHO cell line can be produced using ACE technology that performs competitively using a chemically defined fed-batch bioreactor process with comparable product quality attributes to cell lines generated by existing technologies.

Inertial Sensor Technology for Elite Swimming Performance Analysis: A Systematic Review

Science.gov (United States)

Mooney, Robert; Corley, Gavin; Godfrey, Alan; Quinlan, Leo R; ÓLaighin, Gearóid

2015-01-01

Technical evaluation of swimming performance is an essential factor of elite athletic preparation. Novel methods of analysis, incorporating body worn inertial sensors (i.e., Microelectromechanical systems, or MEMS, accelerometers and gyroscopes), have received much attention recently from both research and commercial communities as an alternative to video-based approaches. This technology may allow for improved analysis of stroke mechanics, race performance and energy expenditure, as well as real-time feedback to the coach, potentially enabling more efficient, competitive and quantitative coaching. The aim of this paper is to provide a systematic review of the literature related to the use of inertial sensors for the technical analysis of swimming performance. This paper focuses on providing an evaluation of the accuracy of different feature detection algorithms described in the literature for the analysis of different phases of swimming, specifically starts, turns and free-swimming. The consequences associated with different sensor attachment locations are also considered for both single and multiple sensor configurations. Additional information such as this should help practitioners to select the most appropriate systems and methods for extracting the key performance related parameters that are important to them for analysing their swimmers’ performance and may serve to inform both applied and research practices. PMID:26712760

[Decision modeling for economic evaluation of health technologies].

Science.gov (United States)

de Soárez, Patrícia Coelho; Soares, Marta Oliveira; Novaes, Hillegonda Maria Dutilh

2014-10-01

Most economic evaluations that participate in decision-making processes for incorporation and financing of technologies of health systems use decision models to assess the costs and benefits of the compared strategies. Despite the large number of economic evaluations conducted in Brazil, there is a pressing need to conduct an in-depth methodological study of the types of decision models and their applicability in our setting. The objective of this literature review is to contribute to the knowledge and use of decision models in the national context of economic evaluations of health technologies. This article presents general definitions about models and concerns with their use; it describes the main models: decision trees, Markov chains, micro-simulation, simulation of discrete and dynamic events; it discusses the elements involved in the choice of model; and exemplifies the models addressed in national economic evaluation studies of diagnostic and therapeutic preventive technologies and health programs.

SANDIA NATIONAL LABORATORIES IN SITU ELECTROKINETIC EXTRACTION TECHNOLOGY; INNOVATIVE TECHNOLOGY EVALUATION REPORT

Science.gov (United States)

As a part of the Superfund Innovative Technology Evaluation (SITE) Program, the U.S. Environmental Protection Agency evaluated the In-Situ Electrokinetic Extraction (ISEE) system at Sandia National Laboratories, Albuquerque, New Mexico.The SITE demonstration results show ...

Evaluation of Trenchless Installation Technology for Radioactive Wastewater Piping Applications

International Nuclear Information System (INIS)

Robinson, Sharon M.; Jubin, Robert Thomas; Patton, Bradley D.; Sullivan, Nicholas M.; Bugbee, Kathy P.

2009-01-01

the sanitary sewer and natural gas pipeline industries, they have been used far less in contaminated environments. Although trenchless technologies have been used at ORNL in limited applications to install new potable water and gas lines, the technologies have not been used in radioactive applications. This study evaluates the technical risks, benefits, and economics for installing gravity drained and pressurized piping using trenchless technologies compared to conventional installation methods for radioactive applications under ORNL geological conditions. A range of trenchless installation technologies was reviewed for this report for general applicability for replacing existing contaminated piping and/or installing new pipelines in potentially contaminated areas. Installation methods that were determined to have potential for use in typical ORNL contaminated environments were then evaluated in more detail for three specific ORNL applications. Each feasible alternative was evaluated against the baseline conventional open trench installation method using weighted criteria in the areas of environment, safety, and health (ES and H); project cost and schedule; and technical operability. The formulation of alternatives for evaluation, the development of selection criteria, and the scoring of alternatives were performed by ORNL staff with input from vendors and consultants. A description of the evaluation methodology and the evaluation results are documented in the following sections of this report.

Performance evaluation of paper embossing tools produced by fused deposition modelling additive manufacturing technology

Directory of Open Access Journals (Sweden)

Gordana Delić

2017-12-01

Full Text Available From its beginnings, up to a few years ago, additive manufacturing technology was able to produce models or prototypes which have limited use, because of materials mechanical properties. With advancement and invention of new materials, this is changing. Now, it is possible to create 3D prints that can be used as final products or functional tools, using technology and materials with low environmental impact. The goal of this study was to examine opportunities for production of paper embossing tools by fused deposition modelling (FDM 3D printing. This study emphasises the use of environmentally friendly poly-lactic acid (PLA materials in FDM technology, contrary to the conventional method using metal alloys and acids. Embossing of line elements and letters using 3D printed embossing tools was done on six different types of paper. Embossing force was applied using SHIMADZU EZ-LX Compact Tabletop Testing Machine. Each type of paper was repeatedly embossed using different values of embossing force (in 250 N increments, starting at 1000 N to determine the optimal embossing force for each specific paper type. When determined, the optimal embossing force was used on ten samples for each paper type. Results of embossing were analysed and evaluated. The analysis consisted of investigating the effects of the applied embossing force and characteristics such as paper basis weight, paper structure, surface characteristic and fibre direction of the paper. Results show that paper characteristics determine the embossing force required for achieving a good embossing result. This means that with the right amount of embossing force, letters and borderlines can be equally well formed by the embossing process regardless of paper weight, surface characteristics, etc. Embossing tools produced in this manner can be used in case of the embossing elements that are not complex. The reason for this is the limitation of FDM technology and lack of precision needed for fine

Performance evaluation of 8 CT scanners for clinical use in Italy

International Nuclear Information System (INIS)

Pinto, I.; De Denaro, M.; Giribona, P.; Gicericin, C.; Bravar, D.

1988-01-01

In the past few years the use of CT scanners has widely spread in Italian care institutions. This methodology has thus become an important creates the need for an accurate study of the various aspects of the phenomenon, e.g. technological, diagnostic and economic. In order to evaluate the quality of the CT scanners used in our country, the majors suppliers of the Italian market were asked to provide us with a unit from their production. Six out of 7 companies complied with our request. A standard protocol was used to evaluate the performance of 8 CT scanners, currently used in Italy. The following parameters were evaluated: spatial resolution, contrast resolution, noise, slice thickness, uniformity, linearity and radiation dose. Five currently-used operating modalities were employed. The results allow an overall assessment of the performance of the 8 CT scanners

Evaluation of spacecraft technology programs (effects on communication satellite business ventures), volume 1

Science.gov (United States)

Greenburg, J. S.; Gaelick, C.; Kaplan, M.; Fishman, J.; Hopkins, C.

1985-01-01

Commercial organizations as well as government agencies invest in spacecraft (S/C) technology programs that are aimed at increasing the performance of communications satellites. The value of these programs must be measured in terms of their impacts on the financial performane of the business ventures that may ultimately utilize the communications satellites. An economic evaluation and planning capability was developed and used to assess the impact of NASA on-orbit propulsion and space power programs on typical fixed satellite service (FSS) and direct broadcast service (DBS) communications satellite business ventures. Typical FSS and DBS spin and three-axis stabilized spacecraft were configured in the absence of NASA technology programs. These spacecraft were reconfigured taking into account the anticipated results of NASA specified on-orbit propulsion and space power programs. In general, the NASA technology programs resulted in spacecraft with increased capability. The developed methodology for assessing the value of spacecraft technology programs in terms of their impact on the financial performance of communication satellite business ventures is described. Results of the assessment of NASA specified on-orbit propulsion and space power technology programs are presented for typical FSS and DBS business ventures.

Evaluation of User Acceptance of Mixed Reality Technology

Science.gov (United States)

Yusoff, Rasimah Che Mohd; Zaman, Halimah Badioze; Ahmad, Azlina

2011-01-01

This study investigates users' perception and acceptance of mixed reality (MR) technology. Acceptance of new information technologies has been important research area since 1990s. It is important to understand the reasons why people accept information technologies, as this can help to improve design, evaluation and prediction how users will…

Long-Term Evaluation of SSL Field Performance in Select Interior Projects

Energy Technology Data Exchange (ETDEWEB)

Perrin, Tess E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Davis, Robert G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wilkerson, Andrea M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2017-02-28

This GATEWAY project evaluated four field installations to better understand the long-term performance of a number of LED products, which can hopefully stimulate improvements in designing, manufacturing, specifying, procuring, and installing LED products. Field studies provide the opportunity to discover and investigate issues that cannot be simulated or uncovered in a laboratory, but the installed performance over time of commercially available LED products has not been well documented. Improving long-term performance can provide both direct energy savings by reducing the need to over-light to account for light loss and indirect energy savings through better market penetration due to SSL’s competitive advantages over less-efficient light source technologies. The projects evaluated for this report illustrate that SSL use is often motivated by advantages other than energy savings, including maintenance savings, easier integration with control systems, and improved lighting quality.

Human Performance Evaluation System

International Nuclear Information System (INIS)

Hardwick, R.J. Jr.

1985-01-01

Operating nuclear power plants requires high standards of performance, extensive training and responsive management. Despite our best efforts inappropriate human actions do occur, but they can be managed. An extensive review of License Event Reports (LERs) was conducted which indicated continual inadequacy in human performance and in evaluation of root causes. Of some 31,000 LERs, about 5,000 or 16% were directly attributable to inappropriate actions. A recent analysis of 87 Significant Event Reports (issued by INPO in 1983) identified inappropriate actions as being the most frequent root cause (44% of the total). A more recent analysis of SERs issued in 1983 and 1984 indicate that 52% of the root causes were attributed to human performance. The Human Performance Evaluation System (HPES) is a comprehensive, coordinated utility/industry system for evaluating and reporting human performance situtations. HPES is a result of the realization that current reporting system provide limited treatment of human performance and rarely provide adequate information about root causes of inappropriate actions by individuals. The HPES was implemented to identify and eliminate root causes of inappropriate actions

Utilising digital technology for dialogue and evaluation

DEFF Research Database (Denmark)

Kjærgaard, Thomas

2016-01-01

This article investigates how digital technology can enhance evaluation and eflection through dialogue in a theory lesson in the context of university college teaching. The pedagogical designs in the article vary from synchronous classroom evaluation on smartphones, to online discussion fora...

Utilising digital technology for dialogue and evaluation

DEFF Research Database (Denmark)

Kjærgaard, Thomas

2016-01-01

This article investigates how digital technology can enhance evaluation and reflection through dialogue in a theory lesson in the context of university college teaching. The pedagogical designs in the article vary from synchronous classroom evaluation on smartphones, to online discussion fora...

TEXACO GASIFICATION PROCESS - INNOVATIVE TECHNOLOGY EVALUATION REPORT

Science.gov (United States)

This report summarizes the evaluation of the Texaco Gasification Process (TGP) conducted under the U.S. Environmental Protection Agency (EPA) Superfund Innovative Technology Evaluation (SITE) Program. The Texaco Gasification Process was developed by Texaco Inc. The TGP is a comm...

Materials performance in advanced fossil technologies

International Nuclear Information System (INIS)

Natesan, K.

1991-01-01

A number of advanced technologies are being developed to convert coal into clean fuels for use as a feedstock in chemical plants and for power generation. From the standpoint of component materials, the environments created by coal conversion and combustion in these technologies and their interactions with materials are of interest. This article identifies several modes of materials degradation and possible mechanisms for metal wastage. Available data on the performance of materials in several of the environments are highlighted, and examples of promising research activities to improve the corrosion resistance of materials are presented

Technology performance evaluation of scientific and educational activities of scientific-pedagogical staff in higher education

Directory of Open Access Journals (Sweden)

Bechvaya Maria, R.

2015-12-01

Full Text Available This paper proposes a performance assessment tool research and teaching staff on the basis of a rating system that allows for the analysis of the results of key personnel of the higher school for criteria and determine the size of incentive payments. The rating model wage researchers and teachers bases on strengthening the incentive function of wages, aimed at personalization of scientific and educational activities of employees, which in modern conditions is the most relevant for use. The functions of stimulation, such as economic, moral and social are considered. The analysis methodologies for assessing university in the world and national rankings on the basis of which formed a system of indicators for assessing the activities of academic staff of higher education is represented. The necessity of development of an information system through which it is possible to carry out comprehensive analysis, that is to monitor the number of registered employees, to determine the share indices in the total ranking, to conduct the ranking points received by employees by industry and science in the context of structural units. The proposed information system is one element of technology assessment of effectiveness of the academic staff designed to evaluate the effectiveness of their activities and incentives, allows the analysis of criteria, based on which can be applied informed management decisions regarding the development of social and labor relations in the highest school.

48 CFR 2936.604 - Performance evaluation.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Performance evaluation... Performance evaluation. (a) The HCA must establish procedures to evaluate architect-engineer contractor... reports must be made using Standard Form 1421, Performance Evaluation (Architect-Engineer) as prescribed...

A Study of KHNP Nuclear Power Plant Technology Level Evaluation

International Nuclear Information System (INIS)

Yang, Seung Han; Lee, Sung Jin; Kim, Yo Han

2016-01-01

KHNP's 2030 mid and long term plan goal in technology field is securing global No. 1 NPP technology level. Quantifying technology level for this purpose, technology level at present should be surveyed. Technology level of South Korea has been surveyed by KISTEP (Korea Institute of S and T Evaluation and Planning) every two year but the technology level of KHNP has not been surveyed by any organization including KHNP itself. Also the size of technology surveyed by KISTEP was too broad to quantifying technology level of KHNP. In this paper, technology level of KHNP and South Korea are presented. In this study, NPP related technologies were divided into Level I and Level II technologies and conducted a survey for each Level II technologies using Delphi questionnaire survey that is widely used in technology level evaluation. The results of technology level and gap will be used from strategic point of view and also as a reference data for technology improvement planning

A Study of KHNP Nuclear Power Plant Technology Level Evaluation

Energy Technology Data Exchange (ETDEWEB)

Yang, Seung Han; Lee, Sung Jin; Kim, Yo Han [KHNP, Daejeon (Korea, Republic of)

2016-05-15

KHNP's 2030 mid and long term plan goal in technology field is securing global No. 1 NPP technology level. Quantifying technology level for this purpose, technology level at present should be surveyed. Technology level of South Korea has been surveyed by KISTEP (Korea Institute of S and T Evaluation and Planning) every two year but the technology level of KHNP has not been surveyed by any organization including KHNP itself. Also the size of technology surveyed by KISTEP was too broad to quantifying technology level of KHNP. In this paper, technology level of KHNP and South Korea are presented. In this study, NPP related technologies were divided into Level I and Level II technologies and conducted a survey for each Level II technologies using Delphi questionnaire survey that is widely used in technology level evaluation. The results of technology level and gap will be used from strategic point of view and also as a reference data for technology improvement planning.

48 CFR 236.604 - Performance evaluation.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Performance evaluation... Architect-Engineer Services 236.604 Performance evaluation. (a) Preparation of performance reports. Use DD Form 2631, Performance Evaluation (Architect-Engineer), instead of SF 1421. (2) Prepare a separate...

Experiments and Pilot Study Evaluating the Performance of Reading Miscue Detector and Automated Reading Tutor for Filipino: A Children's Speech Technology for Improving Literacy

Directory of Open Access Journals (Sweden)

Ronald M. Pascual

2017-06-01

Full Text Available The latest advances in speech processing technology have allowed the development of automated reading tutors (ART for improving children's literacy. An ART is a computer-assisted learning system based on oral reading fluency (ORF instruction and automated speech recognition (ASR technology. However, the design of an ART system is language-specif ic, and thus, requires developing a system specif ically for the Filipino language. In a previous work, the authors have presented the development of the children's Filipino speech corpus (CFSC for the purpose of designing an ART in Filipino. In this paper, the authors present the evaluation of the ART in Filipino which integrates a reference verification (RV- and word duration analysis-based reading miscue detector (RMD, a user interface, and a feedback and instruction set. The authors also present the performance evaluation of the RMD in offline tests, and the effectiveness of the ART as shown by the results of the intervention program, a month-long pilot study that involved the use of the ART by a small group of students. Offline test results show that the RMD's performance (i.e., FA rate ≈ 3% and MDerr rate ≈ 5% is at par with those from state-of-the-art RMDs reported in the literature. The results of the ART intervention experiment showed that the students, on the average, have improved in their words correct per minute (WCPM rate by 4.66 times, in their ORF-16 scores by 6.0 times, and in their reading comprehension exam scores by 4.4 times, after using the ART.

13 CFR 304.4 - Performance evaluations.

Science.gov (United States)

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Performance evaluations. 304.4... ECONOMIC DEVELOPMENT DISTRICTS § 304.4 Performance evaluations. (a) EDA shall evaluate the management... of at least one (1) other District Organization in the performance evaluation on a cost-reimbursement...

Methane mitigation timelines to inform energy technology evaluation

Science.gov (United States)

Roy, Mandira; Edwards, Morgan R.; Trancik, Jessika E.

2015-11-01

Energy technologies emitting differing proportions of methane (CH4) and carbon dioxide (CO2) vary significantly in their relative climate impacts over time, due to the distinct atmospheric lifetimes and radiative efficiencies of the two gases. Standard technology comparisons using the global warming potential (GWP) with a fixed time horizon do not account for the timing of emissions in relation to climate policy goals. Here we develop a portfolio optimization model that incorporates changes in technology impacts based on the temporal proximity of emissions to a radiative forcing (RF) stabilization target. An optimal portfolio, maximizing allowed energy consumption while meeting the RF target, is obtained by year-wise minimization of the marginal RF impact in an intended stabilization year. The optimal portfolio calls for using certain higher-CH4-emitting technologies prior to an optimal switching year, followed by CH4-light technologies as the stabilization year approaches. We apply the model to evaluate transportation technology pairs and find that accounting for dynamic emissions impacts, in place of using the static GWP, can result in CH4 mitigation timelines and technology transitions that allow for significantly greater energy consumption while meeting a climate policy target. The results can inform the forward-looking evaluation of energy technologies by engineers, private investors, and policy makers.

Methane mitigation timelines to inform energy technology evaluation

International Nuclear Information System (INIS)

Roy, Mandira; Edwards, Morgan R; Trancik, Jessika E

2015-01-01

Energy technologies emitting differing proportions of methane (CH 4 ) and carbon dioxide (CO 2 ) vary significantly in their relative climate impacts over time, due to the distinct atmospheric lifetimes and radiative efficiencies of the two gases. Standard technology comparisons using the global warming potential (GWP) with a fixed time horizon do not account for the timing of emissions in relation to climate policy goals. Here we develop a portfolio optimization model that incorporates changes in technology impacts based on the temporal proximity of emissions to a radiative forcing (RF) stabilization target. An optimal portfolio, maximizing allowed energy consumption while meeting the RF target, is obtained by year-wise minimization of the marginal RF impact in an intended stabilization year. The optimal portfolio calls for using certain higher-CH 4 -emitting technologies prior to an optimal switching year, followed by CH 4 -light technologies as the stabilization year approaches. We apply the model to evaluate transportation technology pairs and find that accounting for dynamic emissions impacts, in place of using the static GWP, can result in CH 4 mitigation timelines and technology transitions that allow for significantly greater energy consumption while meeting a climate policy target. The results can inform the forward-looking evaluation of energy technologies by engineers, private investors, and policy makers. (letter)

An evaluation of alternative reactor vessel cutting technologies for the experimental boiling water reactor at Argonne National Laboratory

International Nuclear Information System (INIS)

Boing, L.E.; Henley, D.R.; Manion, W.J.; Gordon, J.W.

1989-12-01

Metal cutting techniques that can be used to segment the reactor pressure vessel of the Experimental Boiling Water Reactor (EBWR) at Argonne National Laboratory (ANL) have been evaluated by Nuclear Energy Services. Twelve cutting technologies are described in terms of their ability to perform the required task, their performance characteristics, environmental and radiological impacts, and cost and schedule considerations. Specific recommendations regarding which technology should ultimately be used by ANL are included. The selection of a cutting method was the responsibility of the decommissioning staff at ANL, who included a relative weighting of the parameters described in this document in their evaluation process. 73 refs., 26 figs., 69 tabs

An evaluation of alternative reactor vessel cutting technologies for the experimental boiling water reactor at Argonne National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Boing, L.E.; Henley, D.R. (Argonne National Lab., IL (USA)); Manion, W.J.; Gordon, J.W. (Nuclear Energy Services, Inc., Danbury, CT (USA))

1989-12-01

Metal cutting techniques that can be used to segment the reactor pressure vessel of the Experimental Boiling Water Reactor (EBWR) at Argonne National Laboratory (ANL) have been evaluated by Nuclear Energy Services. Twelve cutting technologies are described in terms of their ability to perform the required task, their performance characteristics, environmental and radiological impacts, and cost and schedule considerations. Specific recommendations regarding which technology should ultimately be used by ANL are included. The selection of a cutting method was the responsibility of the decommissioning staff at ANL, who included a relative weighting of the parameters described in this document in their evaluation process. 73 refs., 26 figs., 69 tabs.

Recent technology on steam turbine performance improvement

International Nuclear Information System (INIS)

Hirada, M.; Watanabe, E.; Tashiro, H.

1991-01-01

Continuous efforts have been made to improve turbine efficiency by applying the latest aerodynamic technologies to meet the energy saving requirement. In recent years, there has been considerable improvement in the field of computational fluid dynamics and these new technologies have been applied to the new blade design for HP, IP and LP turbines. Experimental verification for the new blade in turbine tests has established the overall turbine performance improvement and the excellent correspondence of flow pattern to the predicted value. This paper introduces the latest design technologies for the newly developed high efficiency blade and the verification test results

Performance Management Practices, Information and Communication Technology (ICT) Adoption and Managed Performance

Science.gov (United States)

Kagaari, James R. K.; Munene, John C.; Ntayi, Joseph Mpeera

2010-01-01

Purpose: The purpose of this paper is to demonstrate the need for managers of public universities to pay attention to performance management practices and information communication technology (ICT) adoption in order to achieve successful managed performance. Design/methodology/approach: Using a disproportionate stratified purposive approach, a…

Evaluation of innovative arsenic treatment technologies :the arsenic water technology partnership vendors forums summary report.

Energy Technology Data Exchange (ETDEWEB)

Everett, Randy L.; Siegel, Malcolm Dean; McConnell, Paul E.; Kirby, Carolyn (Comforce Technical Services, Inc.)

2006-09-01

The lowering of the drinking water standard (MCL) for arsenic from 50 {micro}g/L to 10 {micro}g/L in January 2006 could lead to significant increases in the cost of water for many rural systems throughout the United States. The Arsenic Water Technology Partnership (AWTP), a collaborative effort of Sandia National Laboratories, the Awwa Research Foundation (AwwaRF) and WERC: A Consortium for Environmental Education and Technology Development, was formed to address this problem by developing and testing novel treatment technologies that could potentially reduce the costs of arsenic treatment. As a member of the AWTP, Sandia National Laboratories evaluated cutting-edge commercial products in three annual Arsenic Treatment Technology Vendors Forums held during the annual New Mexico Environmental Health Conferences (NMEHC) in 2003, 2004 and 2005. The Forums were comprised of two parts. At the first session, open to all conference attendees, commercial developers of innovative treatment technologies gave 15-minute talks that described project histories demonstrating the effectiveness of their products. During the second part, these same technologies were evaluated and ranked in closed sessions by independent technical experts for possible use in pilot-scale field demonstrations being conducted by Sandia National Laboratories. The results of the evaluations including numerical rankings of the products, links to company websites and copies of presentations made by the representatives of the companies are posted on the project website at http://www.sandia.gov/water/arsenic.htm. This report summarizes the contents of the website by providing brief descriptions of the technologies represented at the Forums and the results of the evaluations.

Evaluation of Technologies for Retrieval of Waste from Leaking Tanks

International Nuclear Information System (INIS)

Bamberger, Judith A.; Hatchell, Brian K.; Lewis, Benjamin E.; Randolph, John D.; Killough, Stephen M.

2000-01-01

The US Department of Energy Environmental and Waste Management Tanks Focus Area selected as a strategic initiative the need to identify and develop technologies for remediation of tanks that are known or are suspected to leak. This investigation identified and evaluated technical options for single-shell tank waste retrieval applicable to retrieve waste from potentially leaking tanks. Technologies that minimize leakage use minimal water, and dry retrieval technologies were evaluated. Safety, cost, authorization basis, and schedule risks were identified for each technology to provide River Protection Program with information to evaluate technical and programmatic risk. A workshop was held to identify technology needs and solutions. These approaches grouped into five categories: those related to waste dislodging, waste conveyance, both waste dislodging and conveyance, the deployment platform, and technologies related to leak detection, monitoring, and mitigation. Based on the ranking, six technologies were selected as potential candidates for further evaluation. These items were prioritized into four technologies to recommend for further evaluation (1) Air assisted TORE(R). The TORE(R) produces a processing vortex core with the ability to convey solids at pre-determined slurry concentrations over great distances. The dry TORE(R) concept uses air to develop the vortex to fluidize dry solids. The TORE(R)the solids in a slurry transport line. (2) Sonication for waste dislodging utilizes ultrasonic energy to fracture and dislodge hard waste types such as salt cake and sludge. (3) Novel long-reach manipulators concept is to investigate novel cost effective approaches for long-reach manipulator technology. (4) Next generation crawler technology envisions a non-umbilical dislodger, possibly radio controlled and powered remotely to provide a deployment platform not affected by path, or the need to retrace steps

European network for Health Technology Assessment Joint Action (EUnetHTA JA): a process evaluation performed by questionnaires and documentary analysis.

Science.gov (United States)

Woodford Guegan, Eleanor; Cook, Andrew

2014-06-01

The European network for Health Technology Assessment Joint Action (EUnetHTA JA) project's overarching objective was to 'establish an effective and sustainable HTA [Health technology assessment] collaboration in Europe that brings added value at the regional, national and European level'. Specific objectives were to develop a strategy and business model for sustainable European collaboration on HTA, develop HTA tools and methods and promote good practice in HTA methods and processes. We describe activities performed on behalf of the National Institute for Health Research HTA programme; evaluating the project processes and developing a data set for a registry of planned clinical studies of relevance to public funders. Annual self-completion online questionnaires were sent to project participants and external stakeholders to identify their views about the project processes. Documentary review was undertaken at the project end on the final technical reports from the work packages to examine whether or not their deliverables had been achieved. The project's impact was assessed by whether or not the deliverables were produced, the objectives met and additional 'added value' generated. The project's effectiveness was evaluated by its processes, communication, administration, workings of individual work packages and involvement of external stakeholders. A two-stage Delphi exercise was undertaken to identify the data elements that should be included in a registry of planned clinical studies of relevance to public funders. The data set was validated by an efficacy testing exercise. High response rates were achieved for the questionnaires sent to project participants and this was attributed to the evidence-based strategy implemented. Response rates to questionnaires sent to external stakeholders were disappointingly lower. Most of the high-level objectives were achieved, although applying the developed tools in practice will be implemented in the European network for Health

ECONOMIC EVALUATION OF CO2 SEQUESTRATION TECHNOLOGIES TASK 4, BIOMASS GASIFICATION-BASED PROCESSING

Energy Technology Data Exchange (ETDEWEB)

Martha L. Rollins; Les Reardon; David Nichols; Patrick Lee; Millicent Moore; Mike Crim; Robert Luttrell; Evan Hughes

2002-04-01

Biomass derived energy currently accounts for about 3 quads of total primary energy use in the United States. Of this amount, about 0.8 quads are used for power generation. Several biomass energy production technologies exist today which contribute to this energy mix. Biomass combustion technologies have been the dominant source of biomass energy production, both historically and during the past two decades of expansion of modern biomass energy in the U. S. and Europe. As a research and development activity, biomass gasification has usually been the major emphasis as a method of more efficiently utilizing the energy potential of biomass, particularly wood. Numerous biomass gasification technologies exist today in various stages of development. Some are simple systems, while others employ a high degree of integration for maximum energy utilization. The purpose of this study is to conduct a technical and economic comparison of up to three biomass gasification technologies, including the carbon dioxide emissions reduction potential of each. To accomplish this, a literature search was first conducted to determine which technologies were most promising based on a specific set of criteria. During this reporting period, the technical and economic performances of the selected processes were evaluated using computer models and available literature. The results of these evaluations are summarized in this report.

Drivers of international performance of Brazilian technology-based firms

OpenAIRE

Serpa Fagundes de Oliveira, Maria Carolina; Scherer, Flavia Luciane; Schneider Hahn, Ivanete; de Moura Carpes, Aletéia; Brachak dos Santos, Maríndia; Nunes Piveta, Maíra

2018-01-01

For Technology-Based Firms, international expansion represents an opportunity for growth and value creation. The present study was designed to analyze the role of technology-based companies (TBCs) internationalization drivers on international performance. Therefore, a descriptive research was carried out with a quantitative approach performed through a survey. Data collection happened with 53 Brazilian TBCs located in innovation habitats. These data were analyzed by multivariate statistical t...

Performance Evaluation of LoRa Considering Scenario Conditions.

Science.gov (United States)

Sanchez-Iborra, Ramon; Sanchez-Gomez, Jesus; Ballesta-Viñas, Juan; Cano, Maria-Dolores; Skarmeta, Antonio F

2018-03-03

New verticals within the Internet of Things (IoT) paradigm such as smart cities, smart farming, or goods monitoring, among many others, are demanding strong requirements to the Radio Access Network (RAN) in terms of coverage, end-node's power consumption, and scalability. The technologies employed so far to provide IoT scenarios with connectivity, e.g., wireless sensor network and cellular technologies, are not able to simultaneously cope with these three requirements. Thus, a novel solution known as Low Power - Wide Area Network (LP-WAN) has emerged as a promising alternative to provide with low-cost and low-power-consumption connectivity to end-nodes spread in a wide area. Concretely, the Long-Range Wide Area Network (LoRaWAN) technology is one of the LP-WAN platforms that is receiving greater attention from both the industry and the academia. For that reason, in this work, a comprehensive performance evaluation of LoRaWAN under different environmental conditions is presented. The results are obtained from three real scenarios, namely, urban, suburban, and rural, considering both dynamic and static conditions, hence a discussion about the most proper LoRaWAN physical-layer configuration for each scenario is provided. Besides, a theoretical coverage study is also conducted by the use of a radio planning tool considering topographic maps and a precise propagation model. From the attained results, it can be concluded that it is necessary to evaluate the propagation conditions of the deployment scenario prior to the system implantation in order to reach a compromise between the robustness of the network and the transmission data-rate.

Performance Engineering Technology for Scientific Component Software

Energy Technology Data Exchange (ETDEWEB)

Malony, Allen D.

2007-05-08

Large-scale, complex scientific applications are beginning to benefit from the use of component software design methodology and technology for software development. Integral to the success of component-based applications is the ability to achieve high-performing code solutions through the use of performance engineering tools for both intra-component and inter-component analysis and optimization. Our work on this project aimed to develop performance engineering technology for scientific component software in association with the DOE CCTTSS SciDAC project (active during the contract period) and the broader Common Component Architecture (CCA) community. Our specific implementation objectives were to extend the TAU performance system and Program Database Toolkit (PDT) to support performance instrumentation, measurement, and analysis of CCA components and frameworks, and to develop performance measurement and monitoring infrastructure that could be integrated in CCA applications. These objectives have been met in the completion of all project milestones and in the transfer of the technology into the continuing CCA activities as part of the DOE TASCS SciDAC2 effort. In addition to these achievements, over the past three years, we have been an active member of the CCA Forum, attending all meetings and serving in several working groups, such as the CCA Toolkit working group, the CQoS working group, and the Tutorial working group. We have contributed significantly to CCA tutorials since SC'04, hosted two CCA meetings, participated in the annual ACTS workshops, and were co-authors on the recent CCA journal paper [24]. There are four main areas where our project has delivered results: component performance instrumentation and measurement, component performance modeling and optimization, performance database and data mining, and online performance monitoring. This final report outlines the achievements in these areas for the entire project period. The submitted progress

Advanced transport systems analysis, modeling, and evaluation of performances

CERN Document Server

Janić, Milan

2014-01-01

This book provides a systematic analysis, modeling and evaluation of the performance of advanced transport systems. It offers an innovative approach by presenting a multidimensional examination of the performance of advanced transport systems and transport modes, useful for both theoretical and practical purposes. Advanced transport systems for the twenty-first century are characterized by the superiority of one or several of their infrastructural, technical/technological, operational, economic, environmental, social, and policy performances as compared to their conventional counterparts. The advanced transport systems considered include: Bus Rapid Transit (BRT) and Personal Rapid Transit (PRT) systems in urban area(s), electric and fuel cell passenger cars, high speed tilting trains, High Speed Rail (HSR), Trans Rapid Maglev (TRM), Evacuated Tube Transport system (ETT), advanced commercial subsonic and Supersonic Transport Aircraft (STA), conventionally- and Liquid Hydrogen (LH2)-fuelled commercial air trans...

Oak Ridge National Laboratory Technology Logic Diagram. Volume 1, Technology Evaluation: Part B, Remedial Action

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

The Oak Ridge National Laboratory Technology Logic Diagram (TLD) was developed to provide a decision-support tool that relates environmental restoration (ER) and waste management (WM) problems at Oak Ridge National Laboratory (ORNL) to potential technologies that can remediate these problems. The TLD identifies the research, development, demonstration, testing, and evaluation needed to develop these technologies to a state that allows technology transfer and application to decontamination and decommissioning (D&D), remedial action (RA), and WM activities. The TLD consists of three fundamentally separate volumes: Vol. 1 (Technology Evaluation), Vol. 2 (Technology Logic Diagram), and Vol. 3 (Technology Evaluation Data Sheets). Part A of Vols. 1 and 2 focuses on D&D. Part B of Vols. 1 and 2 focuses on RA of contaminated facilities. Part C of Vols. 1 and 2 focuses on WM. Each part of Vol. 1 contains an overview of the TLD, an explanation of the program-specific responsibilities, a review of identified technologies, and the ranking os remedial technologies. Volume 2 (Pts. A, B, and C) contains the logic linkages among EM goals, environmental problems, and the various technologies that have the potential to solve these problems. Volume 3 (Pts. A, B, and C) contains the TLD data sheets. The focus of Vol. 1, Pt. B, is RA, and it has been divided into six chapters. The first chapter is an introduction, which defines problems specific to the ER Program for ORNL. Chapter 2 provides a general overview of the TLD. Chapters 3 through 5 are organized into necessary subelement categories: RA, characterization, and robotics and automation. The final chapter contains regulatory compliance information concerning RA.

48 CFR 36.604 - Performance evaluation.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Performance evaluation. 36.604 Section 36.604 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION SPECIAL... Performance evaluation. See 42.1502(f) for the requirements for preparing past performance evaluations for...

Performance evaluation and financial market runs

NARCIS (Netherlands)

Wagner, W.B.

2013-01-01

This paper develops a model in which performance evaluation causes runs by fund managers and results in asset fire sales. Performance evaluation nonetheless is efficient as it disciplines managers. Optimal performance evaluation combines absolute and relative components in order to make runs less

Performance Evaluations in Audit Firms

DEFF Research Database (Denmark)

Riise Johansen, Thomas; Christoffersen, Jeppe

2017-01-01

Previous research has only minimally examined the association between the behaviour and performance evaluations of individual auditors beyond the use of efficiency-focused evaluations. We examine the association between dysfunctional auditor behaviour and three evaluation foci: an efficiency focus......, a client focus and a quality focus. Our results, which are based on questionnaire responses from 196 auditors, demonstrate that an efficiency focus is not associated with dysfunctional behaviour. A client focus is found to be associated with dysfunctional behaviour. Finally, and perhaps most importantly......, our results show that it seems possible to limit dysfunctional behaviours through a quality focus in performance evaluations. Our results provide insights of use to practitioners and regulators on how performance evaluations may not only induce but also reduce dysfunctional auditor behaviours....

Employees Technology Usage Adaptation Impact on Companies’ Logistics Service Performance

Directory of Open Access Journals (Sweden)

A. Zafer ACAR

2018-01-01

Full Text Available The information technology (IT capability of companies is one of the determinants of their competitive power. However, IT outputs depend on employees intentions to use them. As a technological investment Port automation systems are widely used in container terminals. Therefore behavioral intention in the usage of various IT applications is one of the important factors that may affect logistics service performance. This study aims to explore the employees' technology usage adaptation impact on the logistics service performance of ports. In this context, the behavioral intentions of employees who use port automation systems are investigated using the Technological Acceptance Model.

Life cycle evaluation of emerging lignocellulosic ethanol conversion technologies.

Science.gov (United States)

Spatari, Sabrina; Bagley, David M; MacLean, Heather L

2010-01-01

Lignocellulosic ethanol holds promise for addressing climate change and energy security issues associated with personal transportation through lowering the fuel mixes' carbon intensity and petroleum demand. We compare the technological features and life cycle environmental impacts of near- and mid-term ethanol bioconversion technologies in the United States. Key uncertainties in the major processes: pre-treatment, hydrolysis, and fermentation are evaluated. The potential to reduce fossil energy use and greenhouse gas (GHG) emissions varies among bioconversion processes, although all options studied are considerably more attractive than gasoline. Anticipated future performance is found to be considerably more attractive than that published in the literature as being achieved to date. Electricity co-product credits are important in characterizing the GHG impacts of different ethanol production pathways; however, in the absence of near-term liquid transportation fuel alternatives to gasoline, optimizing ethanol facilities to produce ethanol (as opposed to co-products) is important for reducing the carbon intensity of the road transportation sector and for energy security.

Evaluation by nanoindentation of technological products manufactured by pulse injection molding process

Directory of Open Access Journals (Sweden)

Natova Margarita

2018-01-01

Full Text Available During conventional polymer injection molding, flow- and weld lines can arise at the molded parts caused by disturbed polymer melt flow when it crosses different parts of the equipment. Such processed plastic goods have discrete zones of inhomogeneities of very small dimensions. In order to stabilize the melt flow and to equalize dimensions of such defective products, an approach for pulse injection molding is applied during production of polymer packagings. Testing methods used for evaluation of macromechanical performance of processed polymer products are not readily applicable to estimate the changes in visual surface obtained during pulse injecting. To overcome this testing inconvenience the performance of processed packagings is evaluated by nanoindentation. Using this method, a quantitative assessment of the polymer properties is obtained from different parts of technological products.

TECHNOLOGY EVALUATION REPORT: SILICATE TECHNOLOGY CORPORATION - SOLIDIFICATION/STABILIZATION OF PCP AND INORGANIC CONTAMINANTS IN SOILS - SELMA, CA

Science.gov (United States)

This Technolgy Evaluation Report evaluates the solidification/stabilization process of Silicate Technology Corporation (STC) for the on-site treatment of contaminated soil The STC immobilization technology uses a proprietary product (FMS Silicate) to chemically stabilize and ...

Improving Operational Risk Management Using Business Performance Management Technologies

Directory of Open Access Journals (Sweden)

Bram Pieket Weeserik

2018-02-01

Full Text Available Operational Risk Management (ORM comprises the continuous management of risks resulting from: human actions, internal processes, systems, and external events. With increasing requirements, complexity and a growing volume of risks, information systems provide benefits for integrating risk management activities and optimizing performance. Business Performance Management (BPM technologies are believed to provide a solution for effective Operational Risk Management by offering several combined technologies including: work flow, data warehousing, (advanced analytics, reporting and dashboards. BPM technologies can be integrated with an organization’s Planning & Control cycle and related to strategic objectives. This manuscript aims to show how ORM can benefit from BPM technologies via the development and practical validation of a new maturity model. The B4ORM maturity model was developed following the Design Science Research approach. The maturity model relates specific maturity levels of ORM processes with BPM technologies applicable for a specific maturity stage. There appears to be a strong relationship (0.78 with ORM process maturity and supporting BPM technologies. The B4ORM maturity model as described in this manuscript provides an ideal path of BPM technologies related to six distinctive stages of ORM, leading towards technologies suitable for continuous improvement of ORM processes and organization-wide integration.

Technology-Supported Performance Assessments for Middle School Geoscience

Science.gov (United States)

Zalles, D. R.; Quellmalz, E.; Rosenquist, A.; Kreikemeier, P.

2002-12-01

Under funding from the World Bank, the U.S. Department of Education, the National Science Foundation, and the Federal Government's Global Learning and Observations to Benefit the Environment Program (GLOBE), SRI International has developed and piloted web-accessible performance assessments that measure K-12 students' abilities to use learning technologies to reason with scientific information and communicate evidence-based conclusions to scientific problems. This presentation will describe the assessments that pertain to geoscience at the middle school level. They are the GLOBE Assessments and EPA Phoenix, an instantiation of SRI's model of assessment design known as Integrative Performance Assessments in Technology (IPAT). All are publicly-available on the web. GLOBE engages students in scientific data collection and observation about the environment. SRI's classroom assessments for GLOBE provide sample student assessment tools and frameworks that allow teachers and students to assess how well students can use the data in scientific inquiry projects. Teachers can use classroom assessment tools on the site to develop integrated investigations for assessing GLOBE within their particular science curricula. Rubrics are provided for measuring students' GLOBE-related skills, and alignments are made to state, national, and international science standards. Sample investigations are provided about atmosphere, hydrology, landcover, soils, earth systems, and visualizations. The IPAT assessments present students with engaging problems rooted in science or social science content, plus sets of tasks and questions that require them to gather relevant information on the web, use reasoning strategies to analyze and interpret the information, use spreadsheets, word processors, and other productivity tools, and communicate evidence-based findings and recommendations. In the process of gathering information and drawing conclusions, students are assessed on how well they can operate

Development and validation of a heuristic model for evaluation of the team performance of operators in nuclear power plants

International Nuclear Information System (INIS)

Kim, Sa Kil; Byun, Seong Nam; Lee, Dhong Hoon

2011-01-01

Highlights: → We develop an estimation model for evaluation of the team performance of MCR. → To build the model, we extract team performance factors through reviewing literatures and identifying behavior markers. → We validate that the model is adaptable to the advanced MCR of nuclear power plants. → As a result, we find that the model is a systematic and objective to measure team performance. - Abstract: The global concerns about safety in the digital technology of the main control room (MCR) are growing as domestic and foreign nuclear power plants are developed with computerized control facilities and human-system interfaces. In a narrow space, the digital technology contributes to a control room environment, which can facilitate the acquisition of all the information needed for operation. Thus, although an individual performance of the advanced MCR can be further improved; there is a limit in expecting an improvement in team performance. The team performance depends on organic coherence as a whole team rather than on the knowledge and skill of an individual operator. Moreover, a good team performance improves communication between and within teams in an efficient manner, and then it can be conducive to addressing unsafe conditions. Respecting this, it is important and necessary to develop methodological technology for the evaluation of operators' teamwork or collaboration, thus enhancing operational performance in nuclear power plant at the MCR. The objectives of this research are twofold: to develop a systematic methodology for evaluation of the team performance of MCR operators in consideration of advanced MCR characteristics, and to validate that the methodology is adaptable to the advanced MCR of nuclear power plants. In order to achieve these two objectives, first, team performance factors were extracted through literature reviews and methodological study concerning team performance theories. Second, the team performance factors were identified and

Towards Reliable Evaluation of Anomaly-Based Intrusion Detection Performance

Science.gov (United States)

Viswanathan, Arun

2012-01-01

This report describes the results of research into the effects of environment-induced noise on the evaluation process for anomaly detectors in the cyber security domain. This research was conducted during a 10-week summer internship program from the 19th of August, 2012 to the 23rd of August, 2012 at the Jet Propulsion Laboratory in Pasadena, California. The research performed lies within the larger context of the Los Angeles Department of Water and Power (LADWP) Smart Grid cyber security project, a Department of Energy (DoE) funded effort involving the Jet Propulsion Laboratory, California Institute of Technology and the University of Southern California/ Information Sciences Institute. The results of the present effort constitute an important contribution towards building more rigorous evaluation paradigms for anomaly-based intrusion detectors in complex cyber physical systems such as the Smart Grid. Anomaly detection is a key strategy for cyber intrusion detection and operates by identifying deviations from profiles of nominal behavior and are thus conceptually appealing for detecting "novel" attacks. Evaluating the performance of such a detector requires assessing: (a) how well it captures the model of nominal behavior, and (b) how well it detects attacks (deviations from normality). Current evaluation methods produce results that give insufficient insight into the operation of a detector, inevitably resulting in a significantly poor characterization of a detectors performance. In this work, we first describe a preliminary taxonomy of key evaluation constructs that are necessary for establishing rigor in the evaluation regime of an anomaly detector. We then focus on clarifying the impact of the operational environment on the manifestation of attacks in monitored data. We show how dynamic and evolving environments can introduce high variability into the data stream perturbing detector performance. Prior research has focused on understanding the impact of this

Evaluation the effectiveness of remote blood pressure monitoring technology in patients with hypertension on the basis of clinical recommendations performance measures

Directory of Open Access Journals (Sweden)

Posnenkova O.M.

2015-06-01

Material and Methods ― Remote BP monitoring was organized on the basis of computer system which automatically in text messages send requests about BP level to Htn patients. Obtained BP results were stored in the system and automatically worked. A doctor corrected a patient’s therapy if necessary based on this information. To evaluate the effectiveness of a new technology one year observation of 97 Htn patients was organized (54.6% – male aged 49±11 years. Patients regularly responded to automated SMS requests the computer system about the level of blood pressure. The effectiveness was evaluated with the help of the following hypertension guidelines performance measures: 1 a part of patients with four or more BP results during the previous 12 months; 2 a part of patients with BP above the goal level who prescribed two or more antihypertensive drugs on the last visit during the previous 12 months; 3 a part of patients with BP above the goal level 140/90 mm Hg who prescribed two or more antihypertensive drugs on the last visit during the previous 12 months; 4 a part of patients with goal blood pressure (less than 140/90 mmHg on the last visit during the previous 12 months. To evaluate a performance of these measures before BP monitoring the data extracted from patients’ ambulatory cards were used. Results ― 62 patients completed one-year BP monitoring A part of patients with four or more BP results during the previous 12 months increased from 21% to 100% (p<0.001. From 70% to 82% increased the part of patients who were prescribed two or more antihypertensive drugs (p=0.091. From 31% to 15% reduced the part of hypertensives with uncontrolled BP who were prescribed less than two antihypertensive drugs on the last visit (p=0.044. After one-year monitoring a goal BP was registered in 77% of Htn patients versus 13% at the start of the observation (p<0.001. Conclusion ― Htn guidelines performance measures allowed evaluate quantitatively the positive influence

Embedding technology into inter-professional best practices in home safety evaluation.

Science.gov (United States)

Burns, Suzanne Perea; Pickens, Noralyn Davel

2017-08-01

To explore inter-professional home evaluators' perspectives and needs for building useful and acceptable decision-support tools for the field of home modifications. Twenty semi-structured interviews were conducted with a range of home modification professionals from different regions of the United States. The interview transcripts were analyzed with a qualitative, descriptive, perspective approach. Technology supports current best practice and has potential to inform decision making through features that could enhance home evaluation processes, quality, efficiency and inter-professional communication. Technological advances with app design have created numerous opportunities for the field of home modifications. Integrating technology and inter-professional best practices will improve home safety evaluation and intervention development to meet client-centred and societal needs. Implications for rehabilitation Understanding home evaluators technology needs for home safety evaluations contributes to the development of app-based assessments. Integrating inter-professional perspectives of best practice and technological needs in an app for home assessments improves processes. Novice and expert home evaluators would benefit from decision support systems embedded in app-based assessments. Adoption of app-based assessment would improve efficiency while remaining client-centred.

U.S. report on fuel performance and technology

Energy Technology Data Exchange (ETDEWEB)

Cook, T [Department of Energy, Washington, DC (United States). Office of Engineering and Technology Development

1997-12-01

The report reviews the following aspects of fuel performance and technology: increased demand on fuel performance;improved fuel failure rate; operating fuel cycles; capacity factor for US nuclear electric generating plants; potential reduction of SNF due to improved fuel burnup.

Technology Evaluation Workshop Report for Tank Waste Chemical Characterization

International Nuclear Information System (INIS)

Eberlein, S.J.

1994-04-01

A Tank Waste Chemical Characterization Technology Evaluation Workshop was held August 24--26, 1993. The workshop was intended to identify and evaluate technologies appropriate for the in situ and hot cell characterization of the chemical composition of Hanford waste tank materials. The participants were asked to identify technologies that show applicability to the needs and good prospects for deployment in the hot cell or tanks. They were also asked to identify the tasks required to pursue the development of specific technologies to deployment readiness. This report describes the findings of the workshop. Three focus areas were identified for detailed discussion: (1) elemental analysis, (2) molecular analysis, and (3) gas analysis. The technologies were restricted to those which do not require sample preparation. Attachment 1 contains the final workshop agenda and a complete list of attendees. An information package (Attachment 2) was provided to all participants in advance to provide information about the Hanford tank environment, needs, current characterization practices, potential deployment approaches, and the evaluation procedure. The participants also received a summary of potential technologies (Attachment 3). The workshop opened with a plenary session, describing the background and issues in more detail. Copies of these presentations are contained in Attachments 4, 5 and 6. This session was followed by breakout sessions in each of the three focus areas. The workshop closed with a plenary session where each focus group presented its findings. This report summarizes the findings of each of the focus groups. The evaluation criteria and information about specific technologies are tabulated at the end of each section in the report. The detailed notes from each focus group are contained in Attachments 7, 8 and 9

Evaluating the Economic Performance of High-Technology Industry and Energy Efficiency: A Case Study of Science Parks in Taiwan

Directory of Open Access Journals (Sweden)

Min-Ren Yan

2013-02-01

Full Text Available High-technology industries provide opportunities for economic growth, but also raise concerns because of their energy-demanding nature. This paper provides an integrated evaluation of both economic benefits and energy efficiency of high-technology industries based on the real data from one of the globally recognized high-technology industrial clusters, the national science parks in Taiwan. A nation-wide industrial Input-Output Analysis is conducted to demonstrate the positive effects of science parks on national economic developments and industrial upgrades. The concept of energy intensity and an energy-efficient economy index are applied to an integrated assessment of the relationship between economic growth and energy consumption. The proposed case study suggests that economic and energy efficiency objectives can be simultaneously achieved by the development of high-technology industries, while three energy policy implications are considered. First, a nation-wide macro viewpoint is needed and high-technology industries should be considered as parts of the national/regional economies by governmental agencies. Second, a proper industrial clustering mechanism and the shared environmental facilities supported by the government, such as planned land and road usage, electricity and water supply, telecommunications system, sewerage system and wastewater treatments, can improve energy efficiency of high-technology industries. Third, the governmental policies on the taxing and management system in science parks would also direct energy-efficient economy of high-technology industries.

Real-time monitoring through the use of technology to enhance performances throughout HIV cascades.

Science.gov (United States)

Avery, Matthew; Mills, Stephen J; Stephan, Eric

2017-09-01

Controlling the HIV epidemic requires strong linkages across a 'cascade' of prevention, testing, and treatment services. Information and communications technology (ICT) offers the potential to monitor and improve the performance of this HIV cascade in real time. We assessed recent (media to expand reach and improve programmatic targeting; technology in healthcare settings to strengthen coordination, guide clinical decision-making and improve clinical interactions; and telephone-based follow-up to improve treatment retention and adherence. With exceptions, publications have tended to be descriptive rather than evaluative, and the evidence-base for the effectiveness of ICT-driven interventions remains mixed. There is widespread recognition of the potential for ICT to improve HIV cascade performance, but with significant challenges. Successful implementation of real-time cascade monitoring will depend upon stakeholder engagement, compatibility with existing workflows, appropriate resource allocation, and managing expectations.

Assessment, evaluation, and testing of technologies for environmental restoration, decontamination, and decommissioning and high level waste management. Progress report

International Nuclear Information System (INIS)

Uzochukwu, G.A.

1997-01-01

Nuclear and commercial non-nuclear technologies that have the potential of meeting the environmental restoration, decontamination and decommissioning, and high-level waste management objectives are being assessed and evaluated. A detailed comparison of innovative technologies available will be performed to determine the safest and most economical technology for meeting these objectives. Information derived from this effort will be matched with the multi-objectives of the environmental restoration, decontamination and decommissioning, and high-level waste management effort to ensure that the best, most economical, and the safest technologies are used in decision making at USDOE-SRS. Technology-related variables will be developed and the resulting data formatted and computerized for multimedia systems. The multimedia system will be made available to technology developers and evaluators to ensure that the best, most economical, and the safest technologies are used in decision making at USDOE-SRS. Technology-related variables will be developed and the resulting data formatted and computerized for multimedia systems. The multimedia system will be made available to technology developers and evaluators to ensure that the safest and most economical technologies are developed for use at SRS and other DOE sites

Assessment, evaluation, and testing of technologies for environmental restoration, decontamination, and decommissioning and high level waste management. Progress report

Energy Technology Data Exchange (ETDEWEB)

Uzochukwu, G.A.

1997-12-31

Nuclear and commercial non-nuclear technologies that have the potential of meeting the environmental restoration, decontamination and decommissioning, and high-level waste management objectives are being assessed and evaluated. A detailed comparison of innovative technologies available will be performed to determine the safest and most economical technology for meeting these objectives. Information derived from this effort will be matched with the multi-objectives of the environmental restoration, decontamination and decommissioning, and high-level waste management effort to ensure that the best, most economical, and the safest technologies are used in decision making at USDOE-SRS. Technology-related variables will be developed and the resulting data formatted and computerized for multimedia systems. The multimedia system will be made available to technology developers and evaluators to ensure that the best, most economical, and the safest technologies are used in decision making at USDOE-SRS. Technology-related variables will be developed and the resulting data formatted and computerized for multimedia systems. The multimedia system will be made available to technology developers and evaluators to ensure that the safest and most economical technologies are developed for use at SRS and other DOE sites.

Evaluation of Smart Grid Technologies Employed for System Reliability Improvement: Pacific Northwest Smart Grid Demonstration Experience

Energy Technology Data Exchange (ETDEWEB)

Agalgaonkar, Yashodhan P.; Hammerstrom, Donald J.

2017-06-01

The Pacific Northwest Smart Grid Demonstration (PNWSGD) was a smart grid technology performance evaluation project that included multiple U.S. states and cooperation from multiple electric utilities in the northwest region. One of the local objectives for the project was to achieve improved distribution system reliability. Toward this end, some PNWSGD utilities automated their distribution systems, including the application of fault detection, isolation, and restoration and advanced metering infrastructure. In light of this investment, a major challenge was to establish a correlation between implementation of these smart grid technologies and actual improvements of distribution system reliability. This paper proposes using Welch’s t-test to objectively determine and quantify whether distribution system reliability is improving over time. The proposed methodology is generic, and it can be implemented by any utility after calculation of the standard reliability indices. The effectiveness of the proposed hypothesis testing approach is demonstrated through comprehensive practical results. It is believed that wider adoption of the proposed approach can help utilities to evaluate a realistic long-term performance of smart grid technologies.

Health services research evaluation principles. Broadening a general framework for evaluating health information technology.

Science.gov (United States)

Sockolow, P S; Crawford, P R; Lehmann, H P

2012-01-01

Our forthcoming national experiment in increased health information technology (HIT) adoption funded by the American Recovery and Reinvestment Act of 2009 will require a comprehensive approach to evaluating HIT. The quality of evaluation studies of HIT to date reveals a need for broader evaluation frameworks that limits the generalizability of findings and the depth of lessons learned. Develop an informatics evaluation framework for health information technology (HIT) integrating components of health services research (HSR) evaluation and informatics evaluation to address identified shortcomings in available HIT evaluation frameworks. A systematic literature review updated and expanded the exhaustive review by Ammenwerth and deKeizer (AdK). From retained studies, criteria were elicited and organized into classes within a framework. The resulting Health Information Technology Research-based Evaluation Framework (HITREF) was used to guide clinician satisfaction survey construction, multi-dimensional analysis of data, and interpretation of findings in an evaluation of a vanguard community health care EHR. The updated review identified 128 electronic health record (EHR) evaluation studies and seven evaluation criteria not in AdK: EHR Selection/Development/Training; Patient Privacy Concerns; Unintended Consequences/ Benefits; Functionality; Patient Satisfaction with EHR; Barriers/Facilitators to Adoption; and Patient Satisfaction with Care. HITREF was used productively and was a complete evaluation framework which included all themes that emerged. We can recommend to future EHR evaluators that they consider adding a complete, research-based HIT evaluation framework, such as HITREF, to their evaluation tools suite to monitor HIT challenges as the federal government strives to increase HIT adoption.

Dry process fuel performance technology development

International Nuclear Information System (INIS)

Kang, Kweon Ho; Kim, K. W.; Kim, B. K.

2006-06-01

The objective of the project is to establish the performance evaluation system of DUPIC fuel during the Phase III R and D. In order to fulfil this objectives, property model development of DUPIC fuel and irradiation test was carried out in Hanaro using the instrumented rig. Also, the analysis on the in-reactor behavior analysis of DUPIC fuel, out-pile test using simulated DUPIC fuel as well as performance and integrity assessment in a commercial reactor were performed during this Phase. The R and D results of the Phase III are summarized as follows: Fabrication process establishment of simulated DUPIC fuel for property measurement, Property model development for the DUPIC fuel, Performance evaluation of DUPIC fuel via irradiation test in Hanaro, Post irradiation examination of irradiated fuel and performance analysis, Development of DUPIC fuel performance code (KAOS)

Dry process fuel performance technology development

Energy Technology Data Exchange (ETDEWEB)

Kang, Kweon Ho; Kim, K. W.; Kim, B. K. (and others)

2006-06-15

The objective of the project is to establish the performance evaluation system of DUPIC fuel during the Phase III R and D. In order to fulfil this objectives, property model development of DUPIC fuel and irradiation test was carried out in Hanaro using the instrumented rig. Also, the analysis on the in-reactor behavior analysis of DUPIC fuel, out-pile test using simulated DUPIC fuel as well as performance and integrity assessment in a commercial reactor were performed during this Phase. The R and D results of the Phase III are summarized as follows: Fabrication process establishment of simulated DUPIC fuel for property measurement, Property model development for the DUPIC fuel, Performance evaluation of DUPIC fuel via irradiation test in Hanaro, Post irradiation examination of irradiated fuel and performance analysis, Development of DUPIC fuel performance code (KAOS)

Small group gender ratios impact biology class performance and peer evaluations.

Science.gov (United States)

Sullivan, Lauren L; Ballen, Cissy J; Cotner, Sehoya

2018-01-01

Women are underrepresented in science, technology, engineering, and mathematics (STEM) disciplines. Evidence suggests the microclimate of the classroom is an important factor influencing female course grades and interest, which encourages retention of women in STEM fields. Here, we test whether the gender composition of small (8-9 person) learning groups impacts course performance, sense of social belonging, and intragroup peer evaluations of intellectual contributions. Across two undergraduate active learning courses in introductory biology, we manipulated the classroom microclimate by varying the gender ratios of learning groups, ranging from 0% female to 100% female. We found that as the percent of women in groups increased, so did overall course performance for all students, regardless of gender. Additionally, women assigned higher peer- evaluations in groups with more women than groups with less women. Our work demonstrates an added benefit of the retention of women in STEM: increased performance for all, and positive peer perceptions for women.

Involving stakeholders in evaluating environmental restoration technologies

International Nuclear Information System (INIS)

McCabe, G.H.; Serie, P.J.

1993-02-01

Involving citizens, interest groups, and regulators in environmental restoration and waste management programs is a challenge for government agencies and the organizations that support them. To be effective, such involvement activities must identify all individuals and groups who have a stake in the cleanup. Their participation must be early, substantive, and meaningful. Stockholders must be able to see how their input was considered and used, and feel that a good- faith effort was made to reconcile conflicting objectives. The Integrated Demonstration for Cleanup of Volatile Organic Compounds at Arid Sites (VOC-Arid ID) is a Department of Energy Office of Technology Development project located at Hanford. Along with technical evaluation of innovative cleanup technologies, the program is conducting an institutional assessment of regulatory and public acceptance of new technologies. Through a series of interviews and workshops, and use of a computerized information management tool, stakeholders are having a voice in the evaluation. Public and regulatory reaction has been positive

Design evaluation in technology assessment: Illustrated by auditory impedance and sound distribution problems

Science.gov (United States)

Halldane, J. F.

1972-01-01

Technology is considered as a culture for changing a physical world and technology assessment questions the inherent cultural capability to modify power and material in support of living organisms. A comprehensive goal-parameter-synthesis-criterion specification is presented as a basis for a rational assessment of technology. The thesis queries the purpose of the assessed problems, the factors considered, the relationships between factors, and the values assigned those factors to accomplish the appropriate purpose. Stationary and sequential evaluation of enviro-organismic systems are delegated to the responsible personalities involved in design; from promoter/designer through contractor to occupant. Discussion includes design goals derived from organismic factors, definitions of human responses which establish viable criteria and relevant correlation models, linking stimulus parameters, and parallel problem-discipline centered design organization. A consistent concept of impedance, as a degradation in the performance of a specified parameter, is introduced to overcome the arbitrary inoperative connotations of terms like noise, discomfort, and glare. Applications of the evaluative specification are illustrated through design problems related to auditory impedance and sound distribution.

Licensee Performance Evaluation: Phase II

International Nuclear Information System (INIS)

Chakoff, H.E.; Speaker, D.M.; Thompson, S.R.; Cohen, S.C.

1979-08-01

This report details work performed during the second phase of a two-phase contract to develop methodology for Licensee Performance Evaluation. The Phase I report, NUREG/CR-0110 details initial efforts on the contract. The model developed in Phase I was used to evaluate nine additional facilities for this report. Performance indicators from noncompliance data were also evaluated. Methodology was developed employing the noncompliance indicators and used for 12 case studies. It was found that licensee event report indicators could be more easily identified and utilized than noncompliance indicators based on presently available data systems. However, noncompliance data, appropriately related to cause, could provide real insight into why performance was what it was

ENVIRONMENTAL TECHNOLOGY VERIFICATION (ETV) PROGRAM: GREEN BUILDING TECHNOLOGIES

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) Environmental Technology Verification (ETV) Program evaluates the performance of innovative air, water, pollution prevention and monitoring technologies that have the potential to improve human health and the environment. This techno...

Evaluation and Selection of Renewable Energy Technologies for Highway Maintenance Facilities

Science.gov (United States)

Andrews, Taylor

The interest in renewable energy has been increasing in recent years as attempts to reduce energy costs as well the consumption of fossil fuels are becoming more common. Companies and organizations are recognizing the increasing reliance on limited fossil fuels' resources, and as competition and costs for these resources grow, alternative solutions are becoming more appealing. Many federally run buildings and associations also have the added pressure of meeting the mandates of federal energy policies that dictate specific savings or reductions. Federal highway maintenance facilities run by the Department of Transportation fall into this category. To help meet energy saving goals, an investigation into potential renewable energy technologies was completed for the Ohio Department of Transportation. This research examined several types of renewable energy technologies and the major factors that affect their performance and evaluated their potential for implementation at highway maintenance facilities. Facilities energy usage data were provided, and a facility survey and site visits were completed to enhance the evaluation of technologies and the suitability for specific projects. Findings and technology recommendations were presented in the form of selection matrices, which were designed to help make selections in future projects. The benefits of utilization of other tools such as analysis software and life cycle assessments were also highlighted. These selection tools were designed to be helpful guides when beginning the pursuit of a renewable energy technology for highway maintenance facilities, and can be applied to other similar building types and projects. This document further discusses the research strategies and findings as well as the recommendations that were made to the personnel overseeing Ohio's highway maintenance facilities.

Performing in Glass: Reproduction, Technology, \\ud Performance and the Bio-Spectacular

OpenAIRE

Furse, Anna F. D.

2006-01-01

Feminist Futures? sets out to ask if and in what ways feminism remains relevant to theatre and performance practice of the twenty-first century. Responding to this question is an excellent, cross-generational mix of theatre scholars and practitioners whose essays engage in lively, cutting edge critical debates on issues such as citizenship, autobiography, cultural heritage, political agency, and body/technology, as circulating in contemporary feminism and performance today. A timely contribut...

Evaluation of Brine Processing Technologies for Spacecraft Wastewater

Science.gov (United States)

Shaw, Hali L.; Flynn, Michael; Wisniewski, Richard; Lee, Jeffery; Jones, Harry; Delzeit, Lance; Shull, Sarah; Sargusingh, Miriam; Beeler, David; Howard, Jeanie;

Performance Evaluation of LoRa Considering Scenario Conditions

Directory of Open Access Journals (Sweden)

Ramon Sanchez-Iborra

2018-03-01

Full Text Available New verticals within the Internet of Things (IoT paradigm such as smart cities, smart farming, or goods monitoring, among many others, are demanding strong requirements to the Radio Access Network (RAN in terms of coverage, end-node’s power consumption, and scalability. The technologies employed so far to provide IoT scenarios with connectivity, e.g., wireless sensor network and cellular technologies, are not able to simultaneously cope with these three requirements. Thus, a novel solution known as Low Power - Wide Area Network (LP-WAN has emerged as a promising alternative to provide with low-cost and low-power-consumption connectivity to end-nodes spread in a wide area. Concretely, the Long-Range Wide Area Network (LoRaWAN technology is one of the LP-WAN platforms that is receiving greater attention from both the industry and the academia. For that reason, in this work, a comprehensive performance evaluation of LoRaWAN under different environmental conditions is presented. The results are obtained from three real scenarios, namely, urban, suburban, and rural, considering both dynamic and static conditions, hence a discussion about the most proper LoRaWAN physical-layer configuration for each scenario is provided. Besides, a theoretical coverage study is also conducted by the use of a radio planning tool considering topographic maps and a precise propagation model. From the attained results, it can be concluded that it is necessary to evaluate the propagation conditions of the deployment scenario prior to the system implantation in order to reach a compromise between the robustness of the network and the transmission data-rate.

On the network protocol performance evaluation for large scale communication system of nuclear plant

International Nuclear Information System (INIS)

Song, K. S.; Lee, T. H.; Kim, H. R.; Kim, D. H.; Ku, I. S.

1998-01-01

Computer technology has been dramatically advanced and it is now natural to apply digital network technology into nuclear plants. Communication architecture for nuclear plant defines the coordination of safety reactor control, balance of plant, subsystem utilities, and plant monitoring functions, and how they are connected and their user interface to guarantee plant performance and guarantee safety requirements. Therefore, to implement a digital network for control and monitoring systems of advanced nuclear plant needs systematic design and evaluation procedures because of responsive and hard real-time process characteristics of nuclear plant. In this paper, we evaluate several digital network protocols in terms of network delay, link failure effects to hard real-time requirements with full scale traffic

Evaluation of selected sewage sludge gasification technological parameters

Science.gov (United States)

Gałko, Grzegorz; Król, Danuta

2018-02-01

Evaluation of selected sewage sludge gasification technological parameters was shown in this paper. Degree of carbon conducted in combustible substance and syngas efficiency (technological readiness coefficient) in accordance with equations were calculated. Enthalpy of individual compounds formation and energy balance were calculated in accordance with rule of Hess.

Exploration Mission Particulate Matter Filtration Technology Performance Testing in a Simulated Spacecraft Cabin Ventilation System

Science.gov (United States)

Agui, Juan H.; Vijayakumar, R.; Perry, Jay L.; Frederick, Kenneth R.; Mccormick, Robert M.

2017-01-01

Human deep space exploration missions will require advances in long-life, low maintenance airborne particulate matter filtration technology. As one of the National Aeronautics and Space Administrations (NASA) developments in this area, a prototype of a new regenerable, multi-stage particulate matter filtration technology was tested in an International Space Station (ISS) module simulation facility. As previously reported, the key features of the filter system include inertial and media filtration with regeneration and in-place media replacement techniques. The testing facility can simulate aspects of the cabin environment aboard the ISS and contains flight-like cabin ventilation system components. The filtration technology test article was installed at the inlet of the central ventilation system duct and instrumented to provide performance data under nominal flow conditions. In-place regeneration operations were also evaluated. The real-time data included pressure drop across the filter stages, process air flow rate, ambient pressure, humidity and temperature. In addition, two video cameras positioned at the filtration technology test articles inlet and outlet were used to capture the mechanical performance of the filter media indexing operation under varying air flow rates. Recent test results are presented and future design recommendations are discussed.

An integrated impact assessment and weighting methodology: evaluation of the environmental consequences of computer display technology substitution.

Science.gov (United States)

Zhou, Xiaoying; Schoenung, Julie M

2007-04-01

Computer display technology is currently in a state of transition, as the traditional technology of cathode ray tubes is being replaced by liquid crystal display flat-panel technology. Technology substitution and process innovation require the evaluation of the trade-offs among environmental impact, cost, and engineering performance attributes. General impact assessment methodologies, decision analysis and management tools, and optimization methods commonly used in engineering cannot efficiently address the issues needed for such evaluation. The conventional Life Cycle Assessment (LCA) process often generates results that can be subject to multiple interpretations, although the advantages of the LCA concept and framework obtain wide recognition. In the present work, the LCA concept is integrated with Quality Function Deployment (QFD), a popular industrial quality management tool, which is used as the framework for the development of our integrated model. The problem of weighting is addressed by using pairwise comparison of stakeholder preferences. Thus, this paper presents a new integrated analytical approach, Integrated Industrial Ecology Function Deployment (I2-EFD), to assess the environmental behavior of alternative technologies in correlation with their performance and economic characteristics. Computer display technology is used as the case study to further develop our methodology through the modification and integration of various quality management tools (e.g., process mapping, prioritization matrix) and statistical methods (e.g., multi-attribute analysis, cluster analysis). Life cycle thinking provides the foundation for our methodology, as we utilize a published LCA report, which stopped at the characterization step, as our starting point. Further, we evaluate the validity and feasibility of our methodology by considering uncertainty and conducting sensitivity analysis.

Robotic Mobile System's Performance-Based MIMO-OFDM Technology

Directory of Open Access Journals (Sweden)

Omar Alani

2009-10-01

Full Text Available In this paper, a predistortion neural network (PDNN architecture has been imposed to the Sniffer Mobile Robot (SNFRbot that is based on spatial multiplexed wireless Orthogonal Frequency Division Multiplexing (OFDM transmission technology. This proposal is used to improve the system performance by combating one of the main drawbacks that is encountered by OFDM technology; Peak-to-Average Power Ratio (PAPR. Simulation results show that using PDNN resulted in better PAPR performance than the previously published work that is based on linear coding, such as Low Density Parity Check (LDPC codes and turbo encoding whether using flat fading channel or a Doppler spread channel.

Improving reservoir performance using new 'smart' well technology

International Nuclear Information System (INIS)

Roggensack, W.D.; Matthews, C.M.

1997-01-01

The technologies that were available in the past to improve reservoir performance include 3-D seismic, coiled tubing, horizontal wells, and PCP's. Future enabling technologies will also include multi-lateral wells, 'smart' wells, underbalanced drilling, and downhole fluids processing. A description of 'smart' well technology was given, defined as well completions which facilitate downhole monitoring and control of production to achieve maximum reserves recovery. The current development for 'smart' wells is focused on offshore and subsea wells for marginal field development and work-over mitigation, with the emphasis in system design for production control of horizontal and multi-lateral wells. Basic 'smart' well configuration, instrumentation and monitoring systems, applications of 'smart' well technology in the Western Canadian Sedimentary Basin, and future developments and applications for the technology in general, were also discussed. 30 figs

Evaluating a National Science and Technology Program Using the Human Capital and Relational Asset Perspectives

Science.gov (United States)

Hung, Chia-Liang; Chou, Jerome Chih-Lung; Roan, Hung-Wei

2010-01-01

The purpose of this research is to evaluate the performance of the National Science and Technology Program (NSTP) by targeting the Taiwan National Telecommunication Program (NTP) initiated in 1998. The Taiwan telecommunications industry has prospered, currently occupying key positions in global markets even though NTP seldom contributes positively…

Exploring Advanced Technology Gas Turbine Engine Design and Performance for the Large Civil Tiltrotor (LCTR)

Science.gov (United States)

Snyder, Christopher A.

2014-01-01

A Large Civil Tiltrotor (LCTR) conceptual design was developed as part of the NASA Heavy Lift Rotorcraft Systems Investigation in order to establish a consistent basis for evaluating the benefits of advanced technology for large tiltrotors. The concept has since evolved into the second-generation LCTR2, designed to carry 90 passengers for 1,000 nautical miles at 300 knots, with vertical takeoff and landing capability. This paper explores gas turbine component performance and cycle parameters to quantify performance gains possible for additional improvements in component and material performance beyond those identified in previous LCTR2 propulsion studies and to identify additional research areas. The vehicle-level characteristics from this advanced technology generation 2 propulsion architecture will help set performance levels as additional propulsion and power systems are conceived to meet ever-increasing requirements for mobility and comfort, while reducing energy use, cost, noise and emissions. The Large Civil Tiltrotor vehicle and mission will be discussed as a starting point for this effort. A few, relevant engine and component technology studies, including previous LCTR2 engine study results will be summarized to help orient the reader on gas turbine engine architecture, performance and limitations. Study assumptions and methodology used to explore engine design and performance, as well as assess vehicle sizing and mission performance will then be discussed. Individual performance for present and advanced engines, as well as engine performance effects on overall vehicle size and mission fuel usage, will be given. All results will be summarized to facilitate understanding the importance and interaction of various component and system performance on overall vehicle characteristics.

Report of the summative evaluation by the advisory committee on research and development of nuclear energy technology

International Nuclear Information System (INIS)

2005-03-01

The Research Evaluation Committee of the Japan Atomic Energy Research Institute (JAERI) set up an advisory Committee on Research and Development of Nuclear Energy Technology in accordance with the 'Fundamental Guideline for the Evaluation of Research and Development (R and D) at JAERI' and its subsidiary regulations. The Advisory Committee on Research and Development of Nuclear Energy Technology evaluated the adequacy of the plans of safety research to be succeeded from JAERI to a new research institute which will be established by integration of JAERI and the Japan Nuclear Cycle Development Institute (JNC). The Advisory Committee consisted of nine specialists from outside the JAERI conducted its activities from July 2004 to August 2004. The evaluation was performed on the basis of the materials submitted in advance and of the oral presentations made at the Advisory Committee meeting which was held on August 10, 2004, in line with the items, viewpoints, and criteria for the evaluation specified by the Research Evaluation Committee. The result of the evaluation by the Advisory Committee was submitted to the Research Evaluation Committee, and was judged to be appropriate at its meeting held on December 1, 2004. This report describes the result of the evaluation by the Advisory Committee on Research and Development on Nuclear Energy Technology. (author)

Does external technology acquisition determine export performance? Evidence from Chinese manufacturing firms

DEFF Research Database (Denmark)

Wang, Yuandi; Cao, Wei; Zhou, Zhao

2013-01-01

understanding of the determinants of export performance by examining the impact of the inter-organizational dimension of innovation strategy to export performance, which has been ignored in the prevailing “strategy tripod” perspective of exporting research. This study is based on a sample of 141 Chinese...... indigenous manufacturing firms that engaged in inward technology licensing between 2000 and 2003. The empirical results indicate that external technology acquisitions positively influence Chinese firms’ export performance. Moreover the exporting performance of using external technology varies depending...

Dissemination of Technology to Evaluate Healthy Food Incentive Programs.

Science.gov (United States)

Freedman, Darcy A; Hunt, Alan R; Merritt, Katie; Shon, En-Jung; Pike, Stephanie N

2017-03-01

Federal policy supports increased implementation of monetary incentive interventions for chronic disease prevention among low-income populations. This study describes how a Prevention Research Center, working with a dissemination partner, developed and distributed technology to support nationwide implementation and evaluation of healthy food incentive programming focused on Supplemental Nutrition Assistance Program recipients. FM Tracks, an iOS-based application and website, was developed to standardize evaluation methods for healthy food incentive program implementation at direct-to-consumer markets. This evaluation examined diffusion and adoption of the technology over 9 months (July 2015-March 2016). Data were analyzed in 2016. FM Tracks was disseminated to 273 markets affiliated with 37 regional networks in 18 states and Washington, DC. All markets adopted the sales transaction data collection feature, with nearly all recording at least one Supplemental Nutrition Assistance Program (99.3%) and healthy food incentive (97.1%) transaction. A total of 43,493 sales transactions were recorded. By the ninth month of technology dissemination, markets were entering individual sales transactions using the application (34.5%) and website (29.9%) and aggregated transactions via website (35.6%) at similar rates. Use of optional evaluation features like recording a customer ID with individual transactions increased successively with a low of 22.2% during the first month to a high of 69.2% in the ninth month. Systematic and widely used evaluation technology creates possibilities for pragmatic research embedded within ongoing, real-world implementation of food access interventions. Technology dissemination requires supportive technical assistance and continuous refinement that can be advanced through academic-practitioner partnerships. Copyright © 2016 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Oak Ridge National Laboratory Technology Logic Diagram. Volume 3, Technology evaluation data sheets: Part B, Dismantlement, Remedial action

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

The Oak Ridge National Laboratory Technology Logic Diagram (TLD) was developed to provide a decision support tool that relates environmental restoration (ER) and waste management (WM) problems at Oak Ridge National Laboratory (ORNL) to potential technologies that can remediate these problems. The TLD identifies the research, development, demonstration testing, and evaluation needed to develop these technologies to a state that allows technology transfer and application to decontamination and decommissioning (D&D), remedial action (RA), and WM activities. The TLD consists of three fundamentally separate volumes: Vol. 1, Technology Evaluation; Vol. 2, Technology Logic Diagram and Vol. 3, Technology EvaLuation Data Sheets. Part A of Vols. 1 and 2 focuses on RA. Part B of Vols. 1 and 2 focuses on the D&D of contaminated facilities. Part C of Vols. 1 and 2 focuses on WM. Each part of Vol. 1 contains an overview of the TM, an explanation of the problems facing the volume-specific program, a review of identified technologies, and rankings of technologies applicable to the site. Volume 2 (Pts. A. B. and C) contains the logic linkages among EM goals, environmental problems, and the various technologies that have the potential to solve these problems. Volume 3 (Pts. A. B, and C) contains the TLD data sheets. This volume provides the technology evaluation data sheets (TEDS) for ER/WM activities (D&D, RA and WM) that are referenced by a TEDS code number in Vol. 2 of the TLD. Each of these sheets represents a single logic trace across the TLD. These sheets contain more detail than is given for the technologies in Vol. 2.

A New Framework for Evaluating the Functional Capabilities of Intra-Enterprise Application Integration Technologies

Directory of Open Access Journals (Sweden)

Hossein Moradi

2010-10-01

Full Text Available Enterprise Application Integration (EAI technologies facilitate the sharing of information and business processes of interrelated information systems in order to achieve the target integrated systems. Different EAI solutions and technologies provide various capabilities which lead to the complexity of their evaluation process. To reduce this complexity, appropriate tools for evaluating the functional capabilities of EAI technologies are required. This paper proposes a new framework for evaluating the functional capabilities of EAI technologies, which simplify the process of evaluating the functional capabilities of intra-enterprise integration technologies and solutions.The proposed framework for evaluating the EAI technologies was enhanced using the structural and conceptual aspects of previous frameworks. It offers a new schema for which various EAI technologies are categorized in different classes and are evaluated based on their supporting level for functional integration capabilities’ criteria.The new framework offers two lists containing integration technologies and their associated classifications, and functional capabilities of integration technologies. The proposed framework is a novel one which can be used by information system experts for evaluation and comparison purposes of various integration technologies.

Clinical Simulation: A Protocol for Evaluation of Mobile Technology.

Science.gov (United States)

Mather, Carey; Jensen, Sanne; Cummings, Elizabeth

2017-01-01

For mobile technology to be accepted at point of care in healthcare environments there is a need to demonstrate benefits whilst ameliorating the risks and challenges. To provide a standardised approach to evaluation of mobile technology a simulation protocol was developed to provide guidance for its use in healthcare environments. Simulated conditions provide the opportunity to assess intended and unintended consequences and identify potential workarounds when using technology. The protocol can also be used to demonstrate the importance of the development of digital professionalism by end-users prior to students entering the clinical practice setting. The mobile technology protocol was adapted from a health information systems protocol developed and used at the ITX Lab, Denmark for use in other simulation laboratories. Use case scenarios were developed to enable evaluation of mobile technology for mobile learning of nurses, nurse supervisors, students and patients. The scenarios can be used in a range of simulated environments including hospital bedside, outpatient clinic or community settings. A case study exemplar of a nurse and patient is included to demonstrate how the mobile technology protocol can be applied.

Technology evaluation report: Biotrol Soil Washing System for treatment of a wood-preserving site. Volume 2, Part B

International Nuclear Information System (INIS)

Skovronek, H.S.; Ellis, W.; Evans, J.; Kitaplioglu, O.; McPherson, J.

1991-12-01

The SITE Program demonstration of one configuration of the BioTrol Soil Washing System (BSWS) was conducted to obtain reliable performance and cost data that can be used to evaluate the potential applicability of the technology as a remediation alternative for sites contaminated with hazardous wastes. The BSWS treatment train used in the study consists of three technologies: a soil washer; an aqueous treatment system; and a slurry bio-reactor. The demonstration was carried out at the MacGillis and Gibbs Superfund site in New Brighton, MN. The report analyzes the results from the SITE demonstration. It includes discussion of the operation of the three separate treatment technologies (SW, SBR, and BATS) evaluated in the test and provides flow diagrams, a summary of the sampling and analytical programs, an economic analysis, and a quality assurance/quality control evaluation of the data. Conclusions were reached concerning the technology's suitability for use in remediations involving both similar and different materials at other sites

Enabling Detailed Energy Analyses via the Technology Performance Exchange: Preprint

Energy Technology Data Exchange (ETDEWEB)

Studer, D.; Fleming, K.; Lee, E.; Livingood, W.

2014-08-01

One of the key tenets to increasing adoption of energy efficiency solutions in the built environment is improving confidence in energy performance. Current industry practices make extensive use of predictive modeling, often via the use of sophisticated hourly or sub-hourly energy simulation programs, to account for site-specific parameters (e.g., climate zone, hours of operation, and space type) and arrive at a performance estimate. While such methods are highly precise, they invariably provide less than ideal accuracy due to a lack of high-quality, foundational energy performance input data. The Technology Performance Exchange was constructed to allow the transparent sharing of foundational, product-specific energy performance data, and leverages significant, external engineering efforts and a modular architecture to efficiently identify and codify the minimum information necessary to accurately predict product energy performance. This strongly-typed database resource represents a novel solution to a difficult and established problem. One of the most exciting benefits is the way in which the Technology Performance Exchange's application programming interface has been leveraged to integrate contributed foundational data into the Building Component Library. Via a series of scripts, data is automatically translated and parsed into the Building Component Library in a format that is immediately usable to the energy modeling community. This paper (1) presents a high-level overview of the project drivers and the structure of the Technology Performance Exchange; (2) offers a detailed examination of how technologies are incorporated and translated into powerful energy modeling code snippets; and (3) examines several benefits of this robust workflow.

Performance Evaluation of Photovoltaic Solar Air Conditioning

Directory of Open Access Journals (Sweden)

Snegirjovs A.

2016-12-01

Full Text Available Information on the electrical-driven solar air conditioning (SAC is rather scanty. A considerable body of technical data mostly concerns large-scale photo-voltaic solar air conditioning (PV-SAC systems. Reliable information about the energy output has arisen only in recent years; however, it is still not easily accessible, and sometimes its sources are closed. Despite these facts, solar energy researchers, observers and designers devote special attention to this type of SAC systems. In this study, performance evaluation is performed for the PV-SAC technology, in which low-power (up to 15 kWp of cooling power on average systems are used. Such a system contains a PV electric-driven compression chiller with cold and heat sensible thermal storage capacities, and a rejected energy unit used for preheating domestic hot water (DHW. In a non-cooling season, it is possible to partly employ the system in the reverse mode for DHW production. In this mode, the ambient air serves as a heat source. Besides, free cooling is integrated in the PV-SAC concept.

Performance Evaluation of Photovoltaic Solar Air Conditioning

Science.gov (United States)

Snegirjovs, A.; Shipkovs, P.; Lebedeva, K.; Kashkarova, G.; Migla, L.; Gantenbein, P.; Omlin, L.

2016-12-01

Information on the electrical-driven solar air conditioning (SAC) is rather scanty. A considerable body of technical data mostly concerns large-scale photo-voltaic solar air conditioning (PV-SAC) systems. Reliable information about the energy output has arisen only in recent years; however, it is still not easily accessible, and sometimes its sources are closed. Despite these facts, solar energy researchers, observers and designers devote special attention to this type of SAC systems. In this study, performance evaluation is performed for the PV-SAC technology, in which low-power (up to 15 kWp of cooling power on average) systems are used. Such a system contains a PV electric-driven compression chiller with cold and heat sensible thermal storage capacities, and a rejected energy unit used for preheating domestic hot water (DHW). In a non-cooling season, it is possible to partly employ the system in the reverse mode for DHW production. In this mode, the ambient air serves as a heat source. Besides, free cooling is integrated in the PV-SAC concept.

Technological evaluation of gesture and speech interfaces for enabling dismounted soldier-robot dialogue

Science.gov (United States)

Kattoju, Ravi Kiran; Barber, Daniel J.; Abich, Julian; Harris, Jonathan

2016-05-01

With increasing necessity for intuitive Soldier-robot communication in military operations and advancements in interactive technologies, autonomous robots have transitioned from assistance tools to functional and operational teammates able to service an array of military operations. Despite improvements in gesture and speech recognition technologies, their effectiveness in supporting Soldier-robot communication is still uncertain. The purpose of the present study was to evaluate the performance of gesture and speech interface technologies to facilitate Soldier-robot communication during a spatial-navigation task with an autonomous robot. Gesture and speech semantically based spatial-navigation commands leveraged existing lexicons for visual and verbal communication from the U.S Army field manual for visual signaling and a previously established Squad Level Vocabulary (SLV). Speech commands were recorded by a Lapel microphone and Microsoft Kinect, and classified by commercial off-the-shelf automatic speech recognition (ASR) software. Visual signals were captured and classified using a custom wireless gesture glove and software. Participants in the experiment commanded a robot to complete a simulated ISR mission in a scaled down urban scenario by delivering a sequence of gesture and speech commands, both individually and simultaneously, to the robot. Performance and reliability of gesture and speech hardware interfaces and recognition tools were analyzed and reported. Analysis of experimental results demonstrated the employed gesture technology has significant potential for enabling bidirectional Soldier-robot team dialogue based on the high classification accuracy and minimal training required to perform gesture commands.

Site characterization at the Rabbit Valley Geophysical Performance Evaluation Range

International Nuclear Information System (INIS)

Koppenjan, S.; Martinez, M.

1994-01-01

The United States Department of Energy (US DOE) is developing a Geophysical Performance Evaluation Range (GPER) at Rabbit Valley located 30 miles west of Grand Junction, Colorado. The purpose of the range is to provide a test area for geophysical instruments and survey procedures. Assessment of equipment accuracy and resolution is accomplished through the use of static and dynamic physical models. These models include targets with fixed configurations and targets that can be re-configured to simulate specific specifications. Initial testing (1991) combined with the current tests at the Rabbit Valley GPER will establish baseline data and will provide performance criteria for the development of geophysical technologies and techniques. The US DOE's Special Technologies Laboratory (STL) staff has conducted a Ground Penetrating Radar (GPR) survey of the site with its stepped FM-CW GPR. Additionally, STL contracted several other geophysical tests. These include an airborne GPR survey incorporating a ''chirped'' FM-CW GPR system and a magnetic survey with a surfaced-towed magnetometer array unit Ground-based and aerial video and still frame pictures were also acquired. STL compiled and analyzed all of the geophysical maps and created a site characterization database. This paper discusses the results of the multi-sensor geophysical studies performed at Rabbit Valley and the future plans for the site

Participatory Evaluation of Monitoring and Modeling of Sustainable Land Management Technologies in Areas Prone to Land Degradation

Science.gov (United States)

Stringer, L. C.; Fleskens, L.; Reed, M. S.; de Vente, J.; Zengin, M.

2014-11-01

Examples of sustainable land management (SLM) exist throughout the world. In many cases, SLM has largely evolved through local traditional practices and incremental experimentation rather than being adopted on the basis of scientific evidence. This means that SLM technologies are often only adopted across small areas. The DESIRE (DESertIfication mitigation and REmediation of degraded land) project combined local traditional knowledge on SLM with empirical evaluation of SLM technologies. The purpose of this was to evaluate and select options for dissemination in 16 sites across 12 countries. It involved (i) an initial workshop to evaluate stakeholder priorities (reported elsewhere), (ii) field trials/empirical modeling, and then, (iii) further stakeholder evaluation workshops. This paper focuses on workshops in which stakeholders evaluated the performance of SLM technologies based on the scientific monitoring and modeling results from 15 study sites. It analyses workshop outcomes to evaluate how scientific results affected stakeholders' perceptions of local SLM technologies. It also assessed the potential of this participatory approach in facilitating wider acceptance and implementation of SLM. In several sites, stakeholder preferences for SLM technologies changed as a consequence of empirical measurements and modeling assessments of each technology. Two workshop examples are presented in depth to: (a) explore the scientific results that triggered stakeholders to change their views; and (b) discuss stakeholders' suggestions on how the adoption of SLM technologies could be up-scaled. The overall multi-stakeholder participatory approach taken is then evaluated. It is concluded that to facilitate broad-scale adoption of SLM technologies, de-contextualized, scientific generalisations must be given local context; scientific findings must be viewed alongside traditional beliefs and both scrutinized with equal rigor; and the knowledge of all kinds of experts must be

Assessment of three-dimensional high-definition visualization technology to perform microvascular anastomosis.

Science.gov (United States)

Wong, Alex K; Davis, Gabrielle B; Nguyen, T JoAnna; Hui, Kenneth J W S; Hwang, Brian H; Chan, Linda S; Zhou, Zhao; Schooler, Wesley G; Chandrasekhar, Bala S; Urata, Mark M

2014-07-01

Traditional visualization techniques in microsurgery require strict positioning in order to maintain the field of visualization. However, static posturing over time may lead to musculoskeletal strain and injury. Three-dimensional high-definition (3DHD) visualization technology may be a useful adjunct to limiting static posturing and improving ergonomics in microsurgery. In this study, we aimed to investigate the benefits of using the 3DHD technology over traditional techniques. A total of 14 volunteers consisting of novice and experienced microsurgeons performed femoral anastomoses on male Sprague-Dawley retired breeder rats using traditional techniques as well as the 3DHD technology and compared the two techniques. Participants subsequently completed a questionnaire regarding their preference in terms of operational parameters, ergonomics, overall quality, and educational benefits. Efficiency was also evaluated by mean times to complete the anastomosis with each technique. A total of 27 anastomoses were performed, 14 of 14 using the traditional microscope and 13 of 14 using the 3DHD technology. Preference toward the traditional modality was noted with respect to the parameters of precision, field adjustments, zoom and focus, depth perception, and overall quality. The 3DHD technique was preferred for improved stamina and less back and eye strain. Participants believed that the 3DHD technique was the better method for learning microsurgery. Longer mean time of anastomosis completion was noted in participants utilizing the 3DHD technique. The 3DHD technology may prove to be valuable in improving proper ergonomics in microsurgery. In addition, it may be useful in medical education when applied to the learning of new microsurgical skills. More studies are warranted to determine its efficacy and safety in a clinical setting. Copyright © 2014 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

NASA Technology Evaluation for Environmental Risk Mitigation Remediation Technology Collaboration Development

Science.gov (United States)

Romeo, James

2013-01-01

NASA is committed to finding solutions to agency cleanup problems that are better, cheaper, and more effective than the status quo. Unfortunately, some potential solutions involve innovative technologies for which NASA remediation managers may not have a high level of understanding or confidence. Since 2004, NASA's Stennis Space Center (SSC) in Mississippi has been pumping groundwater contaminated with trichloroethylene (TCE) and other halogenated volatile organic compounds (HVOC) from their cleanup location designated "Area G" through extraction wells to an aboveground treatment system. Over time, however, the effectiveness of this treatment strategy has diminished and an alternative approach is needed. In 2012, professionals from NASA's Principal Center for Technology Evaluation for Environmental Risk Mitigation (TEERM) introduced SSC managers to an innovative technology for enhancing the performance of SSC's existing pump and treat system. The technology, generally referred to as in situ chemical oxidation (ISCO), involves slowly and continuously injecting a strong but safe chemical oxidant into the groundwater. Treatment is enhanced by a "surfactant-type effect" which causes residual contamination from saturated soil to be released into the dissolved-phase where it can be readily oxidized. Any dissolved-phase contamination that was not oxidized can be collected by the extraction well network and treated aboveground. SSC was not familiar with the technology so to increase their confidence, TEERM identified a contractor who was willing to demonstrate their product and process at a significantly reduced price. An initial, small-scale demonstration of ISCO began at sse in March 2012 and completed in August 2012. This successful demonstration was followed by three larger-scale ISCO demonstrations between August and December 2012. The contractor's innovative Continuous Injection System (CIS) incorporated "green" and sustainable technologies and practices. A slow

Techno-Economic Evaluation of Technologies to Mitigate Greenhouse Gas Emissions at North American Refineries.

Science.gov (United States)

Motazedi, Kavan; Abella, Jessica P; Bergerson, Joule A

2017-02-07

A petroleum refinery model, Petroleum Refinery Life-cycle Inventory Model (PRELIM), that estimates energy use and CO 2 emissions was modified to evaluate the environmental and economic performance of a set of technologies to reduce CO 2 emissions at refineries. Cogeneration of heat and power (CHP), carbon capture at fluid catalytic cracker (FCC) and steam methane reformer (SMR) units, and alternative hydrogen production technologies were considered in the analysis. The results indicate that a 3-44% reduction in total annual refinery CO 2 emissions (2-24% reductions in the CO 2 emissions on a per barrel of crude oil processed) can be achieved in a medium conversion refinery that processes a typical U.S. crude slate obtained by using the technologies considered. A sensitivity analysis of the quality of input crude to a refinery, refinery configuration, and prices of natural gas and electricity revealed how the magnitude of possible CO 2 emissions reductions and the economic performance of the mitigation technologies can vary under different conditions. The analysis can help inform decision making related to investment decisions and CO 2 emissions policy in the refining sector.

Performance Evaluation of Advanced Retrofit Roof Technologies Using Field-Test Data Phase Three Final Report, Volume 2

Energy Technology Data Exchange (ETDEWEB)

Biswas, Kaushik [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Childs, Phillip W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Atchley, Jerald Allen [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-01-01

This article presents some miscellaneous data from two low-slope and two steep-slope experimental roofs. The low-slope roofs were designed to compare the performance of various roof coatings exposed to natural weatherization. The steep-slope roofs contained different combinations of phase change material, rigid insulation, low emittance surface and above-sheathing ventilation, with standing-seam metal panels on top. The steep-slope roofs were constructed on a series of adjacent attics separated at the gables using thick foam insulation. This article describes phase three (3) of a study that began in 2009 to evaluate the energy benefits of a sustainable re-roofing technology utilizing standing-seam metal roofing panels combined with energy efficient features like above-sheathing-ventilation (ASV), phase change material (PCM) and rigid insulation board. The data from phases 1 and 2 have been previously published and reported [Kosny et al., 2011; Biswas et al., 2011; Biswas and Childs, 2012; Kosny et al., 2012]. Based on previous data analyses and discussions within the research group, additional test roofs were installed in May 2012, to test new configurations and further investigate different components of the dynamic insulation systems. Some experimental data from phase 3 testing from May 2012 to December 2013 and some EnergyPlus modeling results have been reported in volumes 1 and 3, respectively, of the final report [Biswas et al., 2014; Biswas and Bhandari, 2014].

Early economic evaluation of emerging health technologies: protocol of a systematic review

Science.gov (United States)

2014-01-01

Background The concept of early health technology assessment, discussed well over a decade, has now been collaboratively implemented by industry, government, and academia to select and expedite the development of emerging technologies that may address the needs of patients and health systems. Early economic evaluation is essential to assess the value of emerging technologies, but empirical data to inform the current practice of early evaluation is limited. We propose a systematic review of early economic evaluation studies in order to better understand the current practice. Methods/design This protocol describes a systematic review of economic evaluation studies of regulated health technologies in which the evaluation is conducted prior to regulatory approval and when the technology effectiveness is not well established. Included studies must report an economic evaluation, defined as the comparative analysis of alternatives with respect to their associated costs and health consequences, and must evaluate some regulated health technology such as pharmaceuticals, biologics, high-risk medical devices, or biomarkers. We will conduct the literature search on multiple databases, including MEDLINE, EMBASE, the Centre for Reviews and Dissemination Databases, and EconLit. Additional citations will be identified via scanning reference lists and author searching. We suspect that many early economic evaluation studies are unpublished, especially those conducted for internal use only. Additionally, we use a chain-referral sampling approach to identify authors of unpublished studies who work in technology discovery and development, starting out with our contact lists and authors who published relevant studies. Citation screening and full-text review will be conducted by pairs of reviewers. Abstracted data will include those related to the decision context and decision problem of the early evaluation, evaluation methods (e.g., data sources, methods, and assumptions used to

Preparing Pre-Service Teachers to Integrate Technology into K-12 Instruction: Evaluation of a Technology-Infused Approach

Science.gov (United States)

Admiraal, Wilfried; van Vugt, Felix; Kranenburg, Frans; Koster, Bob; Smit, Ben; Weijers, Sanne; Lockhorst, Ditte

2017-01-01

The quality of how technology is addressed in teacher education programmes is conditional for how student teachers apply technology in secondary schools after their graduation. Two technology-infused courses of one teacher education programme were evaluated. In line with studies on the development of pre-service teachers' technological,…

DEMONSTRATION OF AQUAFIX AND SAPS PASSIVE MINE WATER TREATMENT TECHNOLOGIES AT SUMMITVILLE MINE SITE, INNOVATIVE TECHNOLOGY EVALUATION REPORT

Science.gov (United States)

As part of the Superfund Innovative Technology Evaluation (SITE) Program, the U.S. Environmental Protection Agency evaluated two passive water treatment (PWT) technologies for metals removal from acid mine drainage (AMD) at the Summitville Mine Superfund Site in southern Colorado...

Elucidate Innovation Performance of Technology-driven Mergers and Acquisitions

Energy Technology Data Exchange (ETDEWEB)

Huang, L.; Wang, K.; Yu, H.; Shang, L.; Mitkova, L.

2016-07-01

The importance and value of Mergers and Acquisitions (M&As) have increased with the expectancy to obtain key technology capabilities and rapid impact on innovation. This article develops an original analytical framework to elucidate the impact of the technology and product relatedness (similarity/complementarity) of the Technology-driven M&A’ partners on post-innovation performance. We present results drawing on a multiple case studies of Chinese High-Tech firms from three industries. (Author)

Distributed utility technology cost, performance, and environmental characteristics

Energy Technology Data Exchange (ETDEWEB)

Wan, Y; Adelman, S

1995-06-01

Distributed Utility (DU) is an emerging concept in which modular generation and storage technologies sited near customer loads in distribution systems and specifically targeted demand-side management programs are used to supplement conventional central station generation plants to meet customer energy service needs. Research has shown that implementation of the DU concept could provide substantial benefits to utilities. This report summarizes the cost, performance, and environmental and siting characteristics of existing and emerging modular generation and storage technologies that are applicable under the DU concept. It is intended to be a practical reference guide for utility planners and engineers seeking information on DU technology options. This work was funded by the Office of Utility Technologies of the US Department of Energy.

Technology Readiness Evaluation For Aluminum Removal And Sodium Hydroxide Regenration From Hanford Tank Waste By Lithium Hydrotalcite Precipitation

International Nuclear Information System (INIS)

Sams, T.L.; Massie, H.L.

2011-01-01

A Technology Readiness Evaluation (TRE) performed by AREV A Federal Services, LLC (AFS) for Washington River Protection Solutions, LLC (WRPS) shows the lithium hydrotalcite (LiHT) process invented and patented (pending) by AFS has reached an overall Technology Readiness Level (TRL) of 3. The LiHT process removes aluminum and regenerates sodium hydroxide. The evaluation used test results obtained with a 2-L laboratory-scale system to validate the process and its critical technology elements (CTEs) on Hanford tank waste simulants. The testing included detailed definition and evaluation for parameters of interest and validation by comparison to analytical predictions and data quality objectives for critical subsystems. The results of the TRE would support the development of strategies to further mature the design and implementation of the LiHT process as a supplemental pretreatment option for Hanford tank waste.

Drivers of international performance of Brazilian technology-based firms

Directory of Open Access Journals (Sweden)

Maria Carolina Serpa Fagundes de Oliveira

2018-01-01

Full Text Available For Technology-Based Firms, international expansion represents an opportunity for growth and value creation. The present study was designed to analyze the role of technology-based companies (TBCs internationalization drivers on international performance. Therefore, a descriptive research was carried out with a quantitative approach performed through a survey. Data collection happened with 53 Brazilian TBCs located in innovation habitats. These data were analyzed by multivariate statistical technique. The results showed that the determinants of the international performance of Brazilian TBCs, can be set by external influencers (localization in innovation habitats, integration into global productive chains, partnerships and strategic alliances for innovation and government policies and internal influencers (innovation capability, international market orientation and international marketing skills.

Development of Out-pile Test Technology for Fuel Assembly Performance Verification

Energy Technology Data Exchange (ETDEWEB)

Chun, Tae Hyun; In, W. K.; Oh, D. S. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)] (and others)

2007-03-15

Out-pile tests with full scale fuel assembly are to verify the design and to evaluate the performance of the final products. HTL for the hydraulic tests and FAMeCT for mechanical/structural tests were constructed in this project. The maximum operating conditions of HTL are 30 bar, 320 .deg. C, and 500 m3/hr. This facility can perform the pressure drop test, fuel assembly uplift test, and flow induced vibration test. FAMeCT can perform the bending and vibration tests. The verification of the developed facilities were carried out by comparing the reference data of the fuel assembly which was obtained at the Westinghouse Co. The compared data showed a good coincidence within uncertainties. FRETONUS was developed for high temperature and high pressure fretting wear simulator and performance test. A performance test was conducted for 500 hours to check the integrity, endurance, data acquisition capability of the simulator. The technology of turbulent flow analysis and finite element analysis by computation was developed. From the establishments of out-pile test facilities for full scale fuel assembly, the domestic infrastructure for PWR fuel development has been greatly upgraded.

A prospective clinical study to evaluate the safety and performance of wireless localization of nonpalpable breast lesions using radiofrequency identification technology.

Science.gov (United States)

Dauphine, Christine; Reicher, Joshua J; Reicher, Murray A; Gondusky, Christina; Khalkhali, Iraj; Kim, Michelle

2015-06-01

The purpose of this study was to evaluate the safety and performance of localizing nonpalpable breast lesions using radiofrequency identification technology. Twenty consecutive women requiring preoperative localization of a breast lesion were recruited. Subjects underwent placement of both a hook wire and a radiofrequency identification tag immediately before surgery. The radiofrequency identification tag was the primary method used by the operating surgeon to localize each lesion during excision, with the hook wire serving as backup in case of tag migration or failed localization. Successful localization with removal of the intended lesion was the primary outcome measured. Tag migration and postoperative infection were also noted to assess safety. Twenty patients underwent placement of a radiofrequency identification tag, 12 under ultrasound guidance and eight with stereotactic guidance. In all cases, the radiofrequency identification tag was successfully localized by the reader at the level of the skin before incision, and the intended lesion was removed along with the radiofrequency identification tag. There were no localization failures and no postoperative infections. Tag migration did not occur before incision, but in three cases, occurred as the lesion was being retracted with fingers to make the final cut along the deep surface of the specimen. In this initial clinical study, radiofrequency tags were safe and able to successfully localize nonpalpable breast lesions. Radiofrequency identification technology may represent an alternative method to hook wire localization.

Perspectives of energy efficient technologies penetration in the Greek domestic sector, through the analysis of Energy Performance Certificates

International Nuclear Information System (INIS)

Gelegenis, J.; Diakoulaki, D.; Lampropoulou, H.; Giannakidis, G.; Samarakou, M.; Plytas, N.

2014-01-01

The building sector in Greece presents a huge energy saving potential, the largest part of which is remaining unexploited. The recently enacted legislation for the energy performance of buildings, in combination with the financial support provided by funding programmes to low income families is expected to significantly boost the deployment of energy efficient technologies in the Greek domestic sector. The exploitation of these legal and financial instruments follows a formalised process of energy audits, resulting in buildings classification and in the submission of Energy Performance Certificates (EPCs) including suggestions to improve the dwellings' energy performance. The paper aims at an ex-ante evaluation of the market trends revealed by EPCs in Greece, in order to identify the perspectives of individual technologies and to assess the degree to which the certification procedure helps in improving the energy performance of buildings. The results indicate a strong trend towards less cost-effective technologies, revealing a sub-optimal allocation of financial resources and putting into risk the path towards the achievement of EU targets for 2020. - Highlights: • Energy Performance Certificates reveal market trends of energy efficient technologies. • SWH, replacement of windows and walls/roof insulation are most often recommended. • Other measures are controls, switch to NG; low cost measures are rarely recommended. • Cost-effectiveness is not the main factor explaining technology recommendations. • Amendment of EPC document and inspection process may enhance its effectiveness

Evaluating the use of prior information under different pacing conditions on aircraft inspection performance: The use of virtual reality technology

Science.gov (United States)

Bowling, Shannon Raye

The aircraft maintenance industry is a complex system consisting of human and machine components, because of this; much emphasis has been placed on improving aircraft-inspection performance. One proven technique for improving inspection performance is the use of training. There are several strategies that have been implemented for training, one of which is feedforward information. The use of prior information (feedforward) is known to positively affect inspection performance. This information can consist of knowledge about defect characteristics (types, severity/criticality, and location) and the probability of occurrence. Although several studies have been conducted that demonstrate the usefulness of feedforward as a training strategy, there are certain research issues that need to be addressed. This study evaluates the effect of feedforward information in a simulated 3-dimensional environment by the use of virtual reality. A controlled study was conducted to evaluate the effectiveness of feedforward information in a simulated aircraft inspection environment. The study was conducted in two phases. The first phase evaluated the difference between general and detailed inspection at different pacing levels. The second phase evaluated the effect of feedforward information pertaining to severity, probability and location. Analyses of the results showed that subjects performing detailed inspection performed significantly better than while performing general inspection. Pacing also had the effect of reducing performance for both general and detailed inspection. The study also found that as the level of feedforward information increases, performance also increases. In addition to evaluating performance measures, the study also evaluated process and subjective measures. It was found that process measures such as number of fixation points, fixation groups, mean fixation duration, and percent area covered were all affected by the treatment levels. Analyses of the subjective

Design and Performance Evaluation of Sensors and Actuators for Advanced Optical Systems

Science.gov (United States)

Clark, Natalie

2011-01-01

Current state-of-the-art commercial sensors and actuators do not meet many of NASA s next generation spacecraft and instrument needs. Nor do they satisfy the DoD needs for satellite missions, especially micro/nano satellite missions. In an effort to develop advanced optical devices and instruments that meet mission requirements, NASA Langley recently completed construction of a new cleanroom housing equipment capable of fabricating high performance active optic and adaptive optic technologies including deformable mirrors, reconfigurable lenses (both refractive and diffractive), spectrometers, spectro-polarimeters, tunable filters and many other active optic devices. In addition to performance, these advanced optic technologies offer advantages in speed, size, weight, power consumption, and radiation tolerance. The active optic devices described in this paper rely on birefringent liquid crystal materials to alter either the phase or the polarization of the incoming light. Design considerations and performance evaluation results for various NASA applications are presented. Applications presented will include large space telescopes, optical communications, spacecraft windows, coronagraphs, and star trackers. Keywords: Photonics, Adaptive Optics, Tunable Filters, MEMs., MOEMs, Coronagraph, Star Tracker

Proposal of an environmental performance index to assess solid waste treatment technologies

International Nuclear Information System (INIS)

Goulart Coelho, Hosmanny Mauro; Lange, Liséte Celina; Coelho, Lineker Max Goulart

2012-01-01

Highlights: ► Proposal of a new concept in waste management: Cleaner Treatment. ► Development of an index to assess quantitatively waste treatment technologies. ► Delphi Method was carried out so as to define environmental indicators. ► Environmental performance evaluation of waste-to-energy plants. - Abstract: Although the concern with sustainable development and environment protection has considerably grown in the last years it is noted that the majority of decision making models and tools are still either excessively tied to economic aspects or geared to the production process. Moreover, existing models focus on the priority steps of solid waste management, beyond waste energy recovery and disposal. So, in order to help the lack of models and tools aiming at the waste treatment and final disposal, a new concept is proposed: the Cleaner Treatment, which is based on the Cleaner Production principles. This paper focuses on the development and validation of the Cleaner Treatment Index (CTI), to assess environmental performance of waste treatment technologies based on the Cleaner Treatment concept. The index is formed by aggregation (summation or product) of several indicators that consists in operational parameters. The weights of the indicator were established by Delphi Method and Brazilian Environmental Laws. In addition, sensitivity analyses were carried out comparing both aggregation methods. Finally, index validation was carried out by applying the CTI to 10 waste-to-energy plants data. From sensitivity analysis and validation results it is possible to infer that summation model is the most suitable aggregation method. For summation method, CTI results were superior to 0.5 (in a scale from 0 to 1) for most facilities evaluated. So, this study demonstrates that CTI is a simple and robust tool to assess and compare the environmental performance of different treatment plants being an excellent quantitative tool to support Cleaner Treatment implementation.

Radionuclide calibrators performance evaluation

International Nuclear Information System (INIS)

Mora Ramirez, E.; Zeledon Fonseca, P.; Jimenez Cordero, M.

2008-01-01

Radionuclide calibrators are used to estimate accurately activity prior to administration to a patient, so it is very important that this equipment meets its performance requirements. The purpose of this paper is to compare the commercially available 'Calicheck' (Calcorp. Inc), used to assess linearity, versus the well-known source decay method, and also to show our results after performing several recommended quality control tests. The parameters that we wanted to evaluate were carried on using the Capintec CRC-15R and CRC-15 β radionuclide calibrators. The evaluated tests were: high voltage, display, zero adjust, background, reproducibility, source constancy, accuracy, precision and linearity. The first six tests were evaluated on the daily practice, here we analyzed the 2007 recorded data; and the last three were evaluated once a year. During the daily evaluation both calibrators performance were satisfactory comparing with the manufacture's requirements. The accuracy test show result within the ± 10% allowed for a field instrument. Precision performance is within the ± 1 % allowed. On the other hand, the linearity test shows that using the source decay method the relative coefficient is 0.9998, for both equipment and using the Calicheck the relative coefficient is 0.997. However, looking the percentage of error, during the 'Calicheck' test, its range goes from 0.0 % up to -25.35%, and using the source decay method, the range goes from 0.0 % up to -31.05 %, taking into account both instruments. Checking the 'Calicheck' results we can see that the results varying randomly, but using the source decay method the percentage of error increase as the source activity decrease. We conclude that both devices meet its manufactures requirements, in the case of the linearity using the decay method, decreasing the activity source, increasing the percentage of error, this may happen because of the equipment age. (author)

Evaluation of technological measures to cope with climate change

Energy Technology Data Exchange (ETDEWEB)

Shimizu, Hiroshi; Moriguchi, Yulchi [National Inst. for Environmental Studies, Onogawa Tsukuba (Japan)

1993-12-31

Because the global warming (climate change) is recognized as a highly probable phenomenon in the next century, the countermeasures to cope with this issue is really Important. International discussion Is progressing towards the conclusion of the treaty to stabilize global warming. Therefore, now is the time to take concrete action to reduce the emission to the greenhouse gases (GHG). To find the way to reduce the emission of the GHG, the procedure as next should be taken. (1) Systematic estimation of GHG emission (GHG analysis), (2) Identification of conventional and Innovative technologies, (3) Assessment of individual sectoral technologies, (4) Comprehensive evaluation of countermeasures as a whole. Both in the U.S.A. and Japan, this kind of research have been made independently. Among these processes, the standard methodologies should be established on the GHG analysis, the assessment of individual technologies and the comprehensive evaluation. From such a background, it is important to discuss the way to evaluate technological measures to cope with climate change between the specialist from the U.S.A. and Japan. And still required to search the possibility to establish a joint project between both countries.

The pattern of performance management of community service learning empowerment in improving the entrepreneurship on the graduation candidate of Vocational Technology Education Institution

Science.gov (United States)

Hadromi

2017-03-01

The purpose of this research is to evaluate the pattern of performance management of Community Service Empowerment Learning-Universitas Negeri Semarang in improving the entrepreneurship of the graduate candidate of Vocational Technology Education Institution. This evaluation research uses Context Evaluation, Input evaluation, Process evaluation and Product evaluation method (CIPP) to evaluate the performance management of Community Service of Empowerment Learning-Universitas Negeri Semarang. The location of research was in Kandri Subdistrict-Indonesia. The subject of research is the Kandri Subdistrict community, especially the groups of the youth, students, subdistrict organizers, community organization, and culinery and handicraft industry, as well as the students who join the program of Community Service of Empowerment Learning-Universitas Negeri Semarang. The object of research is the pattern of perfomance management of Community Service Empowerment Learning-Universitas Negeri Semarang in improving the entrepreneurship of the graduation candidate of Vocational Technology Education Institution. The research result shows the pattern of Community Service Empowerment Learning-Universitas Negeri Semarang is able to improve the enterpreneurship of graduate candidate of Vocational Technology Education Institution. The pattern of Community Service Empowerment Community-Universitas Negeri Semarang which is Education for Sustainable Development (ESD)in the field of education, training, and assistance continuously can grasp and develop competency and balance mindset of students including triple bottom line which mutually connectedamong the sectors of social, economic, cultural, and environment so that it can increase the entrerpreneurship on the graduates candidate of Vocational Technology Education Institution

Simulation studies for the evaluation of health information technologies

DEFF Research Database (Denmark)

Ammenwerth, Elske; Hackl, Werner; Binzer, Kristine

2012-01-01

It is essential for new health information technologies (IT) to undergo rigorous evaluations to ensure they are effective and safe for use in real-world situations. However, evaluation of new health IT is challenging, as field studies are often not feasible when the technology being evaluated...... is not sufficiently mature. Laboratory-based evaluations have also been shown to have insufficient external validity. Simulation studies seem to be a way to bridge this gap. The aim of this study was to evaluate, using a simulation methodology, the impact of a new prototype of an electronic medication management...... system on the appropriateness of prescriptions and drugrelated activities, including laboratory test ordering or medication changes. This article presents the results of a controlled simulation study with 50 simulation runs, including ten doctors and five simulation patients, and discusses experiences...

X-231B technology demonstration for in situ treatment of contaminated soil: Technology evaluation and screening

International Nuclear Information System (INIS)

Siegrist, R.L.; Morris, M.I.; Donaldson, T.L.; Palumbo, A.V.; Herbes, S.E.; Jenkins, R.A.; Morrissey, C.M.; Harris, M.T.

1993-08-01

The Portsmouth Gaseous Diffusion Plant (Ports) is located approximately 70 miles south of Columbus in southern Ohio. Among the several waste management units on the facility, the X-231B unit consists of two adjacent oil biodegradation plots. The plots encompass ∼ 0.8 acres and were reportedly used from 1976 to 1983 for the treatment and disposal of waste oils and degreasing solvents, some containing uranium-235 and technetium-99. The X-231B unit is a regulated solid waste management unit (SWMU) under the Resource Conservation and Recovery Act (RCRA). The X-231B unit is also a designated SWMU located within Quadrant I of the site as defined in an ongoing RCRA Facilities Investigation and Corrective Measures Study (RFI/CMS). Before implementing one or more Technology Demonstration Project must be completed. The principal goal of this project was to elect and successfully demonstrate one ore more technologies for effective treatment of the contaminated soils associated with the X-231B unit at PORTS. The project was divided into two major phases. Phase 1 involved a technology evaluation and screening process. The second phase (i.e., Phase 2) was to involve field demonstration, testing and evaluation of the technology(s) selected during Phase 1. This report presents the methods, results, and conclusions of the technology evaluation and screening portion of the project

Evaluation of EIT system performance.

Science.gov (United States)

Yasin, Mamatjan; Böhm, Stephan; Gaggero, Pascal O; Adler, Andy

2011-07-01

An electrical impedance tomography (EIT) system images internal conductivity from surface electrical stimulation and measurement. Such systems necessarily comprise multiple design choices from cables and hardware design to calibration and image reconstruction. In order to compare EIT systems and study the consequences of changes in system performance, this paper describes a systematic approach to evaluate the performance of the EIT systems. The system to be tested is connected to a saline phantom in which calibrated contrasting test objects are systematically positioned using a position controller. A set of evaluation parameters are proposed which characterize (i) data and image noise, (ii) data accuracy, (iii) detectability of single contrasts and distinguishability of multiple contrasts, and (iv) accuracy of reconstructed image (amplitude, resolution, position and ringing). Using this approach, we evaluate three different EIT systems and illustrate the use of these tools to evaluate and compare performance. In order to facilitate the use of this approach, all details of the phantom, test objects and position controller design are made publicly available including the source code of the evaluation and reporting software.

Synthetic and Enhanced Vision Systems for NextGen (SEVS) Simulation and Flight Test Performance Evaluation

Science.gov (United States)

Shelton, Kevin J.; Kramer, Lynda J.; Ellis,Kyle K.; Rehfeld, Sherri A.

2012-01-01

The Synthetic and Enhanced Vision Systems for NextGen (SEVS) simulation and flight tests are jointly sponsored by NASA's Aviation Safety Program, Vehicle Systems Safety Technology project and the Federal Aviation Administration (FAA). The flight tests were conducted by a team of Honeywell, Gulfstream Aerospace Corporation and NASA personnel with the goal of obtaining pilot-in-the-loop test data for flight validation, verification, and demonstration of selected SEVS operational and system-level performance capabilities. Nine test flights (38 flight hours) were conducted over the summer and fall of 2011. The evaluations were flown in Gulfstream.s G450 flight test aircraft outfitted with the SEVS technology under very low visibility instrument meteorological conditions. Evaluation pilots flew 108 approaches in low visibility weather conditions (600 ft to 2400 ft visibility) into various airports from Louisiana to Maine. In-situ flight performance and subjective workload and acceptability data were collected in collaboration with ground simulation studies at LaRC.s Research Flight Deck simulator.

Evaluation of linear accelerator performance standards using an outcome oriented approach

International Nuclear Information System (INIS)

Rangel, Alejandra; Ploquin, Nicolas; Kay, Ian; Dunscombe, Peter

2008-01-01

Radiation therapy, along with other branches of medicine, is moving towards a firmer basis in evidence to optimally utilize resources. As new treatment technology and strategies place greater demands on quality assurance resources, the need to objectively evaluate equipment and process performance standards from the perspective of predicted clinical impact becomes more urgent. This study evaluates the appropriateness of recommended quality control tolerance and action levels for linear accelerators based on the calculated dosimetric impact of suboptimal equipment performance. A method is described to quantify the dosimetric changes, as reflected by the changes in the outcome surrogate, equivalent uniform dose (EUD), of machine performance deviations from the optimal, specifically in the range of tolerance and action levels promulgated by the Canadian Association of Provincial Cancer Agencies (CAPCA). Linear accelerator performance deviations were simulated for the treatment of prostate, breast, lung, and brain using 3D conformal techniques, and the impact evaluated in terms of the changes in the EUD of the target volumes and two principal organs at risk (OARs) per site. The eight key performance characteristics examined are: Output constancy, beam flatness, gantry angle, collimator angle, field size indicator, laser alignment (three directions) and, by inference, the optical distance indicator. Currently accepted CAPCA tolerance levels for these eight performance characteristics are shown to maintain average EUD deviations to within 2% for the targets and 2 Gy for the OARs. However, within the 2% or 2 Gy range, the recommended tolerance levels are found to have markedly different effects on the EUDs of the structures of interest

Clean coal technologies---An international seminar: Seminar evaluation and identification of potential CCT markets

International Nuclear Information System (INIS)

Guziel, K.A.; Poch, L.A.; Gillette, J.L.; Buehring, W.A.

1991-07-01

The need for environmentally responsible electricity generation is a worldwide concern. Because coal is available throughout the world at a reasonable cost, current research is focusing on technologies that use coal with minimal environmental effects. The United States government is supporting research on clean coal technologies (CCTs) to be used for new capacity additions and for retrofits to existing capacity. To promote the worldwide adoption of US CCTs, the US Department of Energy, the US Agency for International Development, and the US Trade and Development Program sponsored a two-week seminar titled Clean Coal Technologies -- An International Seminar. Nineteen participants from seven countries were invited to this seminar, which was held at Argonne National Laboratory in June 1991. During the seminar, 11 US CCT vendors made presentations on their state-of-the-art and commercially available technologies. The presentations included technical, environmental, operational, and economic characteristics of CCTs. Information on financing and evaluating CCTs also was presented, and participants visited two CCT operating sites. The closing evaluation indicated that the seminar was a worthwhile experience for all participants and that it should be repeated. The participants said CCT could play a role in their existing and future electric capacity, but they agreed that more CCT demonstration projects were needed to confirm the reliability and performance of the technologies

Melter Technologies Assessment

Energy Technology Data Exchange (ETDEWEB)

Perez, J.M. Jr. [Pacific Northwest National Lab., Richland, WA (United States); Schumacher, R.F. [Savannah River Technology Center, Aiken, SC (United States); Forsberg, C.W. [Oak Ridge National Lab., TN (United States)

1996-05-01

The problem of controlling and disposing of surplus fissile material, in particular plutonium, is being addressed by the US Department of Energy (DOE). Immobilization of plutonium by vitrification has been identified as a promising solution. The Melter Evaluation Activity of DOE`s Plutonium Immobilization Task is responsible for evaluating and selecting the preferred melter technologies for vitrification for each of three immobilization options: Greenfield Facility, Adjunct Melter Facility, and Can-In-Canister. A significant number of melter technologies are available for evaluation as a result of vitrification research and development throughout the international communities for over 20 years. This paper describes an evaluation process which will establish the specific requirements of performance against which candidate melter technologies can be carefully evaluated. Melter technologies that have been identified are also described.

Application research for 4D technology in flood forecasting and evaluation

Science.gov (United States)

Li, Ziwei; Liu, Yutong; Cao, Hongjie

1998-08-01

In order to monitor the region which disaster flood happened frequently in China, satisfy the great need of province governments for high accuracy monitoring and evaluated data for disaster and improve the efficiency for repelling disaster, under the Ninth Five-year National Key Technologies Programme, the method was researched for flood forecasting and evaluation using satellite and aerial remoted sensed image and land monitor data. The effective and practicable flood forecasting and evaluation system was established and DongTing Lake was selected as the test site. Modern Digital photogrammetry, remote sensing and GIS technology was used in this system, the disastrous flood could be forecasted and loss can be evaluated base on '4D' (DEM -- Digital Elevation Model, DOQ -- Digital OrthophotoQuads, DRG -- Digital Raster Graph, DTI -- Digital Thematic Information) disaster background database. The technology of gathering and establishing method for '4D' disaster environment background database, application technology for flood forecasting and evaluation based on '4D' background data and experimental results for DongTing Lake test site were introduced in detail in this paper.

Oak Ridge National Laboratory Technology Logic Diagram. Volume 3, Technology evaluation data sheets: Part C, Robotics/automation, Waste management

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

The Oak Ridge National Laboratory Technology Logic Diagram (TLD) was developed to provide a decision support tool that relates environmental restoration (ER) and waste management (WM) problems at Oak Ridge National Laboratory (ORNL) to potential technologies that can remediate these problems. The TLD identifies the research, development, demonstration testing, and evaluation needed to develop these technologies to a state that allows technology transfer and application to decontamination and decommissioning (D&D), remedial action (RA), and WM activities. The TLD consists of three fundamentally separate volumes: Vol. 1, Technology Evaluation; Vol. 2, Technology Logic Diagram and Vol. 3, Technology EvaLuation Data Sheets. Part A of Vols. 1 and 2 focuses on RA. Part B of Vols. 1 and 2 focuses on the D&D of contaminated facilities. Part C of Vols. 1 and 2 focuses on WM. Each part of Vol. 1 contains an overview of the TM, an explanation of the problems facing the volume-specific program, a review of identified technologies, and rankings of technologies applicable to the site. Volume 2 (Pts. A. B. and C) contains the logic linkages among EM goals, environmental problems, and the various technologies that have the potential to solve these problems. Volume 3 (Pts. A. B, and C) contains the TLD data sheets. This volume provides the technology evaluation data sheets (TEDS) for ER/WM activities (D&D, RA and WM) that are referenced by a TEDS code number in Vol. 2 of the TLD. Each of these sheets represents a single logic trace across the TLD. These sheets contain more detail than is given for the technologies in Vol. 2.

Technology development for evaluation of operational quantities in radiation protection

Energy Technology Data Exchange (ETDEWEB)

Kim, Jang Lyul; Chang, S. Y.; Lee, L. T.; Kim, B. H.; Chung, K. K.; Lee, J. I.; Lim, G. S.; Kim, J. S.; Nam, Y. M.; Chang, J. K.; Kim, D. Y.; Yang, J. S

2000-03-01

A study on the fabrication of a new personal thermo-luminescence dosimeter, which can evaluate the personal dose equivalent H{sub p}(d), has been performed. Optimum conditions for fabrication of a LiF:Mg,Cu,Na,Si TL phosphor powder has been determined and a disc type TL pellet has been fabricated from this TL powder. Another type of CaSO{sub 4}:Dy,Mo TL material has been also fabricated. These two TL materials have shown greater TL sensitivity than the foreign-made commercial TL materials. Mono-energetic fluorescence X-ray from 8.6 keV to 75 keV for use in performance testing of the developed TLDs energy response have been constructed and evaluated for the performance of the purity, air kerma, beam uniformity and distribution, and scattered fraction of X-rays. Reference neutron field of a D{sub 2}O moderated {sup 252}Cf source was characterized and the irradiation system using {sup 226}Ra and {sup 137}Cs sources was installed to construct the environmental gamma reference radiation and the low-level gamma radiation. A capability of calibration and measurement of KAERI In Vivo counting system for transuranic elements in the lung has been evaluated through the participation in the overseas intercomparison study on the In Vivo radioactivity measurement. An improvement and advancement of KAERI lung counting technology have been made by the analysis off uncertainties from the assumption of uniform radioactivity distribution in the lung, experimental determination and comparing of detection efficiency with different lung sets, and mathematical efficiency calibration of In Vivo counting system. (author)

LABORATORY EVALUATION OF COMPACTABILITY AND PERFORMANCE OF WARM MIX ASPHALT

Directory of Open Access Journals (Sweden)

Allex Eduardo Álvarez Lugo

Full Text Available Warm mix asphalt (WMA is the term used to describe the set of technologies that allow fabrication of asphalt mixtures at lower temperatures than those specified for conventional hot mix asphalt (HMA. This temperature reduction leads to advantages, compared to construction of HMA, that include energy savings, reduced emissions, and safer working conditions. However, WMA is a relatively new technology and several aspects are still under evaluation. This paper assesses some of these aspects including laboratory compactability and its relation to mixture design, and performance of WMA (i.e., permanent deformation and cracking resistance fabricated with three WMA additives, namely Advera®, Sasobit®, and Evotherm®. Corresponding results showed better or equivalent laboratory compactability for the WMA, as compared to that of the HMA used as reference (or control-HMA, leading to smaller optimum asphalt contents selected based on a specific target density (i.e., 96%. In terms of performance, inclusion of the WMA additives led to decrease the mixture resistance to permanent deformation, although the mixture resistance to cracking can remain similar or even improve as compared to that of the control-HMA.

Post Advanced Technology Implementation Effects on School Psychologist Job Performance

Science.gov (United States)

Hobson, Rana Dirice

2017-01-01

The technology acceptance model (TAM) has been widely used to assess technology adoption in business, education, and health care. The New York City Department of Education (NYCDOE) launched a web-based Individualized Educational Program (IEP) system for school psychologists to use in conducting evaluations and reviews. This quantitative study…

Improved Laser performance through Planar Waveguide Technology Development

Data.gov (United States)

National Aeronautics and Space Administration — We propose a laser technology development to improve efficiency and performance for a variety of science applications including: Lunar Ice, 2-Step Laser Tandem Mass...

ASSESSING INDIVIDUAL PERFORMANCE ON INFORMATION TECHNOLOGY ADOPTION: A NEW MODEL

OpenAIRE

Diah Hari Suryaningrum

2012-01-01

This paper aims to propose a new model in assessing individual performance on information technology adoption. The new model to assess individual performance was derived from two different theories: decomposed theory of planned behavior and task-technology fit theory. Although many researchers have tried to expand these theories, some of their efforts might lack of theoretical assumptions. To overcome this problem and enhance the coherence of the integration, I used a theory from social scien...

An Evaluation of Wind Turbine Technology at Peterson Air Force Base

Science.gov (United States)

2005-03-01

by the wind speed. Darrieus turbines are ordinarily inexpensive and are used for electricity generation and irrigation. One advantage to a...AN EVALUATION OF WIND TURBINE TECHNOLOGY...02 AN EVALUATION OF WIND TURBINE TECHNOLOGY AT PETERSON AIR FORCE BASE THESIS Presented to the Faculty Department of

Evaluation technology of human behavior cognition; Ningen kodo ninchi hyoka gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For human engineering and improvement of the living environment, the evaluation technology of human behavior cognition was studied. For the future reformation and creation of economic structure, the following are required: establishment of safe and affluent communities, further improvement of the safety and harmonious balance of people, lives and society, and R & D close to people and social needs. Introduction of Product Liability law and a fail-safe concept are examples of such efforts. However, since many accidents are found in the human society, the relation between human errors and human characteristics should be studied in detail. The cognitive science of human behavior is an objective evaluation technology from the viewpoint of human being, object, environment and society. Based on these social and technological background, the feasibility of the evaluation technology is studied, and the future trend and skeleton of this project are clarified. The domestic and foreign trends of technologies concerned are thus surveyed, and the important points, features, skeleton and ripple effect of the technology are summarized. 500 refs., 70 figs., 5 tabs.

Performability Modelling Tools, Evaluation Techniques and Applications

NARCIS (Netherlands)

Haverkort, Boudewijn R.H.M.

1990-01-01

This thesis deals with three aspects of quantitative evaluation of fault-tolerant and distributed computer and communication systems: performability evaluation techniques, performability modelling tools, and performability modelling applications. Performability modelling is a relatively new

Evaluation of EUV resist performance using interference lithography

Science.gov (United States)

Buitrago, E.; Yildirim, O.; Verspaget, C.; Tsugama, N.; Hoefnagels, R.; Rispens, G.; Ekinci, Y.

2015-03-01

Extreme ultraviolet lithography (EUVL) stands as the most promising solution for the fabrication of future technology nodes in the semiconductor industry. Nonetheless, the successful introduction of EUVL into the extremely competitive and stringent high-volume manufacturing (HVM) phase remains uncertain partly because of the still limiting performance of EUV resists below 16 nm half-pitch (HP) resolution. Particularly, there exists a trade-off relationship between resolution (half-pitch), sensitivity (dose) and line-edge roughness (LER) that can be achieved with existing materials. This trade-off ultimately hampers their performance and extendibility towards future technology nodes. Here we present a comparative study of highly promising chemically amplified resists (CARs) that have been evaluated using the EUV interference lithography (EUV-IL) tool at the Swiss Light Source (SLS) synchrotron facility in the Paul Scherrer Institute (PSI). In this study we have focused on the performance qualification of different resists mainly for 18 nm and 16 nm half-pitch line/space resolution (L/S = 1:1). Among the most promising candidates tested, there are a few choices that allow for 16 nm HP resolution to be achieved with high exposure latitude (up to ~ 33%), low LER (down to 3.3 nm or ~ 20% of critical dimension CD) and low dose-to-size (or best-energy, BE) < 41 mJ/cm2 values. Patterning was even demonstrated down to 12 nm HP with one of CARs (R1UL1) evaluated for their extendibility beyond the 16 nm HP resolution. 11 nm HP patterning with some pattern collapse and well resolved patterns down 12 nm were also demonstrated with another CAR (R15UL1) formulated for 16 nm HP resolution and below. With such resist it was possible even to obtain a small process window for 14 nm HP processing with an EL ~ 8% (BE ~ 37 mJ/cm2, LER ~ 4.5 nm). Though encouraging, fulfilling all of the requirements necessary for high volume production, such as high resolution, low LER, high photon

Technical and economic evaluation of selected technologies of the Landfill Characterization System

Energy Technology Data Exchange (ETDEWEB)

Floran, R.J.

1993-12-31

In 1992 and 1993, numerous innovative and emerging technologies for characterizing metal and mixed waste contaminants and their migration beneath landfills in and environments were field tested at Sandia`s Chemical Waste Landfill. Many of these technologies are being evaluated as part of the Landfill Characterization System (LCS). The LCS emphasizes minimally intrusive technologies and downhole sensors that strive to be cheaper, better, safer and faster than conventional methods. Major aims of the LCS are to demonstrate, test and evaluate these technologies, and determine whether substantial cost saving over traditional baseline methods can be realized. To achieve these goals, the LCS uses an integrated systems approach that stresses the application of complementary and compatible technologies. Successful field demonstrations combined with favorable economics, will greatly assist the commercialization of these technologies to the private sector and to Environmental Restoration groups throughout the DOE Complex. In this paper, a technical and economic evaluation of selected technologies that comprise the LCS is presented. Because sampling and analysis is the most costly part of a characterization effort, the economic evaluation presented here focuses specifically on these activities. LCS technologies discussed include the ``Smart Sampling Methodology`` and two field screening analytical methods, stripping voltammetry and x-ray fluorescence.

DOE evaluates nine alternative thermal technologies for treatment of mixed waste

International Nuclear Information System (INIS)

Anon.

1995-01-01

In June 1993, the U.S. Department of Energy's (DOE's) Office of Technology Development commissioned a study to evaluate 19 thermal technologies for treating DOE's mixed waste. The study was divided into two phases: Phase I evaluated ten conventional incineration techniques (primarily rotary kiln), and Phase II looked at nine innovative, alternative thermal treatment technologies. The treatment processes were evaluated as part of an integrated waste treatment system, which would include all of the facilities, equipment, and methods required to treat and dispose DOE mixed waste. The relative merits and life-cycle costs were then developed for each of the 19 waste treatment systems evaluated. The study also identified the additional research and development, demonstration, and testing/evaluation steps that would be necessary for the waste treatment systems to successfully treat DOE mixed waste. 3 tabs., 2 refs

Performance Criteria for Capture and/or Immobilization Technologies - Milestone Report

Energy Technology Data Exchange (ETDEWEB)

Bruffey, Stephanie H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jubin, Robert Thomas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Spencer, Barry B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Soelberg, Nick [Idaho National Lab. (INL), Idaho Falls, ID (United States); Riley, Brian [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-02-01

The capture and subsequent immobilization of the four regulated volatile radionuclides (³H, ¹⁴C, ⁸⁵Kr, and ¹²⁹I) from the off-gas streams of a used nuclear fuel (UNF) reprocessing facility has been a topic of substantial research interest for the US Department of Energy and its international colleagues. Removal of some or all of these radionuclides (e.g., based upon fuel burnup, fuel type, cooling time) from the plant effluent streams prior to discharge to the environment is required to meet regulations set forth by the US Environmental Protection Agency. Upon removal, the radionuclide, as well as associated sorbents that cannot be cost-effectively regenerated, is destined for conversion to a waste form. Research in separation and capture methodologies has included a wide range of technologies, including liquid caustic scrubbing systems, solid adsorbents, and cryogenic distillation. The studies of waste forms have been correspondingly diverse. In considering the technologies available for future development and implementation of both sorbents and waste forms, it is necessary to identify benchmark measures of performance to evaluate objectively each sorbent system or waste form.

Fiscal year 1998 Battelle performance evaluation agreement revision 1

Energy Technology Data Exchange (ETDEWEB)

DAVIS, T.L.

1998-10-22

Fiscal Year 1998 represents the second full year utilizing a results-oriented, performance-based contract. This document describes the critical outcomes, objectives, performance indicators, expected levels of performance, and the basis for the evaluation of the Contractors performance for the period October 1, 1997 through September 30, 1998, as required by Articles entitled Use of Objective Standards of Performance, Self Assessment and Performance Evaluation and Critical Outcomes Review of the Contract DE-AC08-76RLO1830. In partnership with the Contractor and other key customers, the Department of Energy (DOE) Richland Operations Office has defined six critical outcomes that same as the core for the Contractors performance evaluation. The Contractor also utilizes these outcomes as a basis for overall management of the Laboratory. As stated above six critical outcomes have been established for FY 1998. These outcomes are based on the following needs identified by DOE-HQ, RL and other customers of the Laboratory. Our Energy Research customer desires relevant, quality and cost effective science. Our Environmental Management customer wants technology developed, demonstrated, and deployed to solve environmental cleanup issues. To ensure the diversification and viability of the Laboratory as a National asset, RL and HQ alike want to increase the Science and Technical contributions of PNNL related to its core capabilities. RL wants improved leadership/management, cost-effective operations, and maintenance of a work environment, which fosters innovative thinking and high morale. RL and HQ alike desire compliance with environment, safety and health (ES and H) standards and disciplined conduct of operations for protection of the worker, environment, and the public, As with all of Hanford, DOE expects contribution of the Laboratory to the economic development of the Tri-Cities community, and the region, to build a new local economy that is less reliant on the Hanford mission

Firms’ Negative Perceptions on Patents, Technology Management Strategies, and Subsequent Performance

Directory of Open Access Journals (Sweden)

Eun Jin Han

2017-03-01

Full Text Available While patents do have many advantages, their disadvantages include requiring disclosure of technical information and imposing the burden of patenting and litigation costs. In this study, we investigate the relationship between a firm’s negative perception on patents, technology management strategies, and subsequent performance. For this purpose, we use a categorical canonical correlation analysis of the top 200, large, R&D-intensive firms in Korea. We find that negative perceptions such as burdensome transaction costs, non-patenting culture, and uncertainty of the outcome of patent litigation are associated with firms’ technology management strategies, such as purchase of licenses, and subsequent performance, such as an increase in the number of inventions from the cross-fertilization of different technologies. The results of this study are expected to contribute to a better understanding of firms’ negative attitudes toward the effects of patents, their subsequent technology management strategies, and resulting performance.

An Orchestrating Evaluation of Complex Educational Technologies: a Case Study of a CSCL System

Directory of Open Access Journals (Sweden)

Luis P. Prieto

2014-06-01

Full Text Available As digital technologies permeate every aspect of our lives, the complexity of the educational settings, and of the technological support we use within them, unceasingly rises. This increased complexity, along with the need for educational practitioners to apply such technologies within multi-constraint authentic settings, has given rise to the notion of technology-enhanced learning practice as “orchestration of learning”. However, at the same time, the complexity involved in evaluating the benefits of such educational technologies has also increased, prompting questions about the way evaluators can cope with the different places, technologies, informants and issues involved in their evaluation activity. By proposing the notion of “orchestrating evaluation”, this paper tries to reconcile the often disparate “front office accounts” of research publications and the “shop floor practice” of evaluation of educational technology, through the case study of evaluating a system to help teachers in coordinating computer-supported collaborative learning (CSCL scenarios. We reuse an internationally-evaluated conceptual framework of “orchestration aspects” (design, management, adaptation, pragmatism, etc. to structure the case‟s narrative, showing how the original evaluation questions and methods were modulated in the face of the multiple (authentic evaluation setting constraints.

LMS Use and Instructor Performance: The Role of Task-Technology Fit

Science.gov (United States)

McGill, Tanya; Klobas, Jane; Renzi, Stefano

2011-01-01

The introduction of learning management systems (LMS) has changed the way in which instructors work. This paper uses Goodhue and Thompson's (1995) technology-to-performance chain (TPC) to explore the roles of task-technology fit (TTF) and level of LMS use in the performance impacts of LMS for instructors. A mixed method approach was used: an…

Elevance of PCDD/PCDF formation for the evaluation of POPs destruction technologies - Necessity and current status

Energy Technology Data Exchange (ETDEWEB)

Weber, R. [Tuebingen Univ. (Germany)

2004-09-15

The Stockholm Convention on Persistent Organic Pollutants (POPs) states in Article 6 that POPs waste should be destroyed or disposed of in a way that the POPs content is destroyed or irreversibly transformed. In this context it is critical that the destruction methods used do not create by-products that are themselves POPs. Therefore one important criterion for assessment of a POPs destruction technology is the potential formation of POPs and other toxic by-products, in particular if higher toxic PCDDs/PCDFs are formed and under which operation conditions their formation is relevant (for the respective POPs destruction technology). A detailed evaluation of non-combustion technologies with respect to PCDD/PCDF formation is lacking to date. Most information with respect to PCDD/PCDF formation in non-combustion technologies in the present stage of evaluation is provided by the companies developing or selling the facility. In a laboratory study it was discovered that super critical water oxidation (SCWO), a technology listed from United Nations Environmental Programme UNEP as ''Commercialised Technology with Considerable Experience'' and from United Nations Industrial Development Organization (UNIDO) as ''Emerging and Innovative Technologies'', has the potential to form high concentrations of PCDFs (in the % range) during PCB destruction. Such elevated PCDF formations might occur even at temperatures of potential application. This highlights the necessity of a more rigorous assessment of non-combustion technologies with respect to their PCDD/PCDF formation potential and their actual applicability for PCB/POPs destruction. The present paper provides a critical impulse in this respect, discusses the relevant formation pathways with respect to POPs destruction technologies and proposes a basic framework on how evaluations may be performed.

ICT evaluation models and performance of medium and small enterprises

Directory of Open Access Journals (Sweden)

Bayaga Anass

2014-01-01

Full Text Available Building on prior research related to (1 impact of information communication technology (ICT and (2 operational risk management (ORM in the context of medium and small enterprises (MSEs, the focus of this study was to investigate the relationship between (1 ICT operational risk management (ORM and (2 performances of MSEs. To achieve the focus, the research investigated evaluating models for understanding the value of ICT ORM in MSEs. Multiple regression, Repeated-Measures Analysis of Variance (RM-ANOVA and Repeated-Measures Multivariate Analysis of Variance (RM-MANOVA were performed. The findings of the distribution revealed that only one variable made a significant percentage contribution to the level of ICT operation in MSEs, the Payback method (β = 0.410, p < .000. It may thus be inferred that the Payback method is the prominent variable, explaining the variation in level of evaluation models affecting ICT adoption within MSEs. Conclusively, in answering the two questions (1 degree of variability explained and (2 predictors, the results revealed that the variable contributed approximately 88.4% of the variations in evaluation models affecting ICT adoption within MSEs. The analysis of variance also revealed that the regression coefficients were real and did not occur by chance

Performance evaluations of the ATST secondary mirror

Science.gov (United States)

Cho, Myung K.; DeVries, Joseph; Hansen, Eric

2007-09-01

The Advanced Technology Solar Telescope (ATST) has a 4.24m off-axis primary mirror designed to deliver diffraction-limited images of the sun. Its baseline secondary mirror (M2) design uses a 0.65m diameter Silicon Carbide mirror mounted kinematically by a bi-pod flexure mechanism at three equally spaced locations. Unlike other common telescopes, the ATST M2 is to be exposed to a significant solar heat loading. A thermal management system will be developed to accommodate the solar loading and minimize "mirror seeing effect" by controlling the temperature difference between the M2 optical surface and the ambient air at the site. Thermo-elastic analyses for steady state thermal behaviors of the ATST secondary mirror was performed using finite element analysis by I-DEAS TM and PCFRINGE TM for the optical analysis. We examined extensive heat transfer simulation cases and their results are discussed. The goal of this study is to evaluate the optical performances of M2 using thermal models and mechanical models. Thermal responses from the models enable us to manipulate time dependent thermal loadings to synthesize the operational environment for the design and development of TMS.

48 CFR 1252.216-72 - Performance evaluation plan.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Performance evaluation....216-72 Performance evaluation plan. As prescribed in (TAR) 48 CFR 1216.406(b), insert the following clause: Performance Evaluation Plan (OCT 1994) (a) A Performance Evaluation Plan shall be unilaterally...

Visegrad Four countries: evaluation in R&D sectors of performance

Directory of Open Access Journals (Sweden)

Nina Bočková

2013-01-01

Full Text Available Competitiveness is currently being studied by many economic analyses. Generalization of the countries’ competitiveness definition as a measure of understanding of the performance evaluation economies is important. Visegrad Four countries: Hungary, the Czech Republic, Slovakia and Poland were admitted to the European Union in May 2004. EU Member States must respect the common EU objectives. The European Union, as expressed in the strategy Europe 2020, is obliged to increase competitiveness, innovation, by introduction of modern technology and especially the growth R&D investment. Limited data to evaluate R&D expenditure: inconsistencies in the R&D support, the absence of data concerning the other means of financing in the sector BERD, limitations of statistical data on the number of innovations only to firms with R&D activities. The aim of this paper is to evaluate the development of R&D expenditures by sector of funding in the Visegrad Four countries in comparison with the values of the EU-27 and countries of Visegrad Four together.

NPP Krsko natural circulation performance evaluation

International Nuclear Information System (INIS)

Segon, Velimir; Bajs, Tomislav; Frogheri, Monica

1999-01-01

The present document deals with an evaluation of the natural circulation performance of the Krsko nuclear power plant. Two calculation have been performed using the NPP Krsko nodalization (both similar to the LOBI A2-77 natural circulation experiment) - the first with the present steam generators at NPP Krsko (Westinghouse, 18% plugged), the second with the future steam generators (Siemens, 0% plugged). The results were evaluated using the natural circulation flow map derived in /1/, and were compared to evaluate the influence of the new steam generators on the natural circulation performance. (author)

METHODS FOR EVALUATION OF COMPANIES’ INFORMATION SYSTEMS AND TECHNOLOGIES EFFICIENCY AND CONTROL IN TEACHING COURSE "INFORMATION TECHNOLOGY GOVERNANCE"

Directory of Open Access Journals (Sweden)

Samchynska Yaroslava

2014-10-01

Full Text Available The use of the information systems and technologies in economic activity is called to represent companies’ corporate principles, aims, traditions, to help in realization of the planned strategies, thanks to that the management efficiency and the cost of enterprise increases. Teaching for educational discipline «IT Governance» is directed on a study and research of these intercommunications by students of the 5th course on specialties «Computer Science», «Software Engineering» for educational level Specialist (Past Bachelor Degree, Master degree. The auditing services belong to the actual methods for evaluation of the information systems and technologies efficiency and control, which are studied according to the course «IT Governance». The article deals with the methodological basis of providing auditing services for evaluation of efficiency and control of information systems (technologies for the purpose of satisfaction of growing informational needs of companies and functional activation in their information resources. The main task of auditing services for control of information systems (information communication technologies efficiency is to evaluate independently and objectively if the information technologies provide the necessary services. The basic criteria, data ware, subject and object of audit necessary for drawing up an audit report and assurance declaring are established. The program and a detailed list of auditing procedures for evaluation of efficiency of information systems and technologies have been presented

A methodology to enable rapid evaluation of aviation environmental impacts and aircraft technologies

Science.gov (United States)

Becker, Keith Frederick

-processing, which does not capture physical interdependencies that may arise at the aircraft-level. The goal of the work that has been conducted here was the development of a methodology to develop surrogate fleet approaches that leverage the capability of physics-based aircraft models and the development of connectivity to fleet-level analysis tools to enable rapid evaluation of fuel burn and emissions metrics. Instead of requiring development of an individual physics-based model for each vehicle in the fleet, the surrogate fleet approaches seek to reduce the number of such models needed while still accurately capturing performance of the fleet. By reducing the number of models, both development time and execution time to generate fleet-level results may also be reduced. The initial steps leading to surrogate fleet formulation were a characterization of the commercial fleet into groups based on capability followed by the selection of a reference vehicle model and a reference set of operations for each group. Next, three potential surrogate fleet approaches were formulated. These approaches include the parametric correction factor approach, in which the results of a reference vehicle model are corrected to match the aggregate results of each group; the average replacement approach, in which a new vehicle model is developed to generate aggregate results of each group, and the best-in-class replacement approach, in which results for a reference vehicle are simply substituted for the entire group. Once candidate surrogate fleet approaches were developed, they were each applied to and evaluated over the set of reference operations. Then each approach was evaluated for their ability to model variations in operations. Finally, the ability of each surrogate fleet approach to capture implementation of different technology suites along with corresponding interdependencies between fuel burn and emissions was evaluated using the concept of a virtual fleet to simulate the technology response

Impact of Digital Tooth Preparation Evaluation Technology on Preclinical Dental Students' Technical and Self-Evaluation Skills.

Science.gov (United States)

Gratton, David G; Kwon, So Ran; Blanchette, Derek; Aquilino, Steven A

2016-01-01

The aim of this study was to evaluate the effect of digital tooth preparation imaging and evaluation technology on dental students' technical abilities, self-evaluation skills, and the assessment of their simulated clinical work. A total of 80 second-year students at one U.S. dental school were assigned to one of three groups: control (n=40), E4D Compare (n=20), and Sirona prepCheck (n=20). Students in the control group were taught by traditional teaching methodologies, and the technology-assisted groups received both traditional training and supplementary feedback from the corresponding digital system. Three outcomes were measured: faculty technical score, self-evaluation score, and E4D Compare scores at 0.30 mm tolerance. Correlations were determined between the groups' scores from visual assessment and self-evaluation and between the visual assessment and digital scores. The results showed that the visual assessment and self-evaluation scores did not differ among groups (p>0.05). Overall, correlations between visual and digital assessment scores were modest though statistically significant (5% level of significance). These results suggest that the use of digital tooth preparation evaluation technology did not impact the students' prosthodontic technical and self-evaluation skills. Visual scores given by faculty and digital assessment scores correlated moderately in only two instances.

Performance evaluation of gas-power strategies for building energy conservation

International Nuclear Information System (INIS)

Gabbar, Hossam A.; Runge, Jason; Bondarenko, Daniel; Bower, Lowell; Pandya, Devarsh; Musharavati, Farayi; Pokharel, Shaligram

2015-01-01

Highlights: • Comparison of natural gas and hydrogen fuels for energy conservation in buildings. • Comparison between hydrogen and natural gas fuel cell is performed. • Simulations of building energy supply. • Performance evaluation of two potential gas-power supply scenarios in buildings. • Natural gas fuel cell showed better performance over hydrogen fuel cell. - Abstract: The work provided herein involves a comparison of natural gas and hydrogen fuels for the purpose of energy conservation for buildings via alternative energy generation methodologies. A case study simulation was developed for an average type of commercial building, a nine storey hotel located in Toronto. The two alternative energy source case studies involved the generation of hydrogen via the wind turbine for the fuel cell, and the use of natural gas directly in the steam reforming fuel cell. The simulations for both scenarios were run and the recorded results were compared to the original case study, as well as between the scenarios. To supply for the base load of the building the fuel cells were given the same kW rating for both scenarios. The identification of all existing technologies for hydrogen gas and natural gas has been carried out, and the similar technologies between the two gases were found. For the purpose of realism, only existing purchasable technologies were considered in this paper. Due to the lack of commercially available technologies for hydrogen gas, only a comparison of fuel cell systems could be accomplished. Over the course of the investigative work it was found that when there is no direct supply of hydrogen to the site of utilization, the natural gas fuel cell is beneficial to the building due to its greater efficiency and lower cost. The major drawback for the hydrogen gas fuel cell, when the on-site generation is involved, is that no thermal power extraction systems currently exist for purchase and utilization in the buildings

Guidance on the Technology Performance Level (TPL) Assessment Methodology

Energy Technology Data Exchange (ETDEWEB)

Weber, Jochem [National Renewable Energy Lab. (NREL), Golden, CO (United States); Roberts, Jesse D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Babarit, Aurelien [Ecole Centrale de Nantes (France). Lab. of Research in Hydrodynamics, Energetics and Atmospheric Environment (LHEEA); Costello, Ronan [Wave Venture, Penstraze (United Kingdom); Bull, Diana L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Neilson, Kim [Ramboll, Copenhagen (Denmark); Bittencourt, Claudio [DNV GL, London (United Kingdom); Kennedy, Ben [Wave Venture, Penstraze (United Kingdom); Malins, Robert Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dykes, Katherine [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-09-01

This document presents the revised Technology Performance Level (TPL) assessment methodology. There are three parts to this revised methodology 1) the Stakeholder Needs and Assessment Guidance (this document), 2) the Technical Submission form, 3) the TPL scoring spreadsheet. The TPL assessment is designed to give a technology neutral or agnostic assessment of any wave energy converter technology. The focus of the TPL is on the performance of the technology in meeting the customer’s needs. The original TPL is described in [1, 2] and those references also detail the critical differences in the nature of the TPL when compared to the more widely used technology readiness level (TRL). (Wave energy TRL is described in [3]). The revised TPL is particularly intended to be useful to investors and also to assist technology developers to conduct comprehensive assessments in a way that is meaningful and attractive to investors. The revised TPL assessment methodology has been derived through a structured Systems Engineering approach. This was a formal process which involved analyzing customer and stakeholder needs through the discipline of Systems Engineering. The results of the process confirmed the high level of completeness of the original methodology presented in [1] (as used in the Wave Energy Prize judging) and now add a significantly increased level of detail in the assessment and an improved more investment focused structure. The revised TPL also incorporates the feedback of the Wave Energy Prize judges.

Evaluation of warm mix asphalt technology in flexible pavements.

Science.gov (United States)

2009-09-01

The primary goal of this research project is to quantify the performance of field produced and placed mixtures that utilize WMA technology and develop a framework for design, construction, and implementation of this technology in Louisiana. This rese...

Waste disposal technologies: designs and evaluations

International Nuclear Information System (INIS)

Shaw, R.A.

1987-01-01

Many states and compacts are presently in the throes of considering what technology to select for their low level waste disposal site. Both the technical and economic aspects of disposal technology are important considerations in these decisions. It is also important that they be considered in the context of the entire system. In the case of a nuclear power plant, that system encompasses the various individual waste streams that contain radioactivity, the processing equipment which reduces the volume and/or alters the form in which the radioisotopes are contained, the packaging of the processed wastes in shipment, and finally its disposal. One further part of this is the monitoring that takes place in all stages of this operation. This paper discusses the results of some research that has been sponsored by EPRI with the principal contractor being Rogers and Associates Engineering Corporation. Included is a description of the distinguishing features found in disposal technologies developed in a generic framework, designs for a selected set of these disposal technologies and the costs which have been derived from these designs. In addition, a description of the early efforts towards defining the performance of these various disposal technologies is described. 5 figures, 1 table

Evaluation of the fusion technology and safety programme of the Joint Research Centre (1980-85)

International Nuclear Information System (INIS)

Haines, M.; Cabibbo, N.; Crocker, J.G.; Lecomte, M.; Merz, E.

1986-01-01

The Joint Research Centre, Ispra, has been involved in fusion research since 1973. In July 1985 the Commission of European Communities - DG XII, following a policy of systematically evaluating its RandD activities, appointed a panel of external experts to evaluate the fusion technology and safety programme carried out at the Joint Research Centre. This report describes the work of the panel in evaluating the research performed by the JRC within the framework of its 1984-87 programme. The achievements of the previous programme, 1980-83, were also taken into consideration. The different research areas covered in the programme, i.e.: reactor studies, breeding blanket technology, structural materials studies, risk assessment and tritium laboratory studies, are described and a draft proposal for the period 1987-90 presented. The evaluation panel has been asked to assess the following aspects: the scientific and technical achievements of the programme, the contribution of the programme to the development of other Community policies, the role played by the JRC in the European fusion research (including NET) and in international collaborations such as INTOR. From its assessment the evaluation panel has made a series of recommendations for the current programme and for future work

Conductor gestures influence evaluations of ensemble performance.

Science.gov (United States)

Morrison, Steven J; Price, Harry E; Smedley, Eric M; Meals, Cory D

2014-01-01

Previous research has found that listener evaluations of ensemble performances vary depending on the expressivity of the conductor's gestures, even when performances are otherwise identical. It was the purpose of the present study to test whether this effect of visual information was evident in the evaluation of specific aspects of ensemble performance: articulation and dynamics. We constructed a set of 32 music performances that combined auditory and visual information and were designed to feature a high degree of contrast along one of two target characteristics: articulation and dynamics. We paired each of four music excerpts recorded by a chamber ensemble in both a high- and low-contrast condition with video of four conductors demonstrating high- and low-contrast gesture specifically appropriate to either articulation or dynamics. Using one of two equivalent test forms, college music majors and non-majors (N = 285) viewed sixteen 30 s performances and evaluated the quality of the ensemble's articulation, dynamics, technique, and tempo along with overall expressivity. Results showed significantly higher evaluations for performances featuring high rather than low conducting expressivity regardless of the ensemble's performance quality. Evaluations for both articulation and dynamics were strongly and positively correlated with evaluations of overall ensemble expressivity.

Development of integrity evaluation technology for pressurized components in nuclear power plant and IT based integrity evaluation system

International Nuclear Information System (INIS)

Kim, Young Jin; Choi, Jae Boong; Shim, Do Jun

2004-02-01

The objective of this research is to develop on efficient integrity evaluation technology and to investigate the applicability of the newly-developed technology such as internet-based cyber platform etc. to Nuclear Power Plant(NPP) components. The development of an efficient structural integrity evaluation system is necessary for safe operation of NPP as the increase of operating periods. Moreover, material test data as well as emerging structural integrity assessment technology are also needed for the evaluation of aged components. The following five topics are covered in this project: development of the wall-thinning evaluation program for nuclear piping; development of structural integrity evaluation criteria for steam generator tubes with cracks of various shape; development of fatigue life evaluation system for major components of NPP; ingegration of internet-based cyber platform and integrity evaluation program for primary components of NPP; effects of aging on strength of dissimilar welds

Development of integrity evaluation technology for pressurized components in nuclear power plant and IT based integrity evaluation system

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Jin; Choi, Jae Boong; Shim, Do Jun [Sungkyunkwan Univ., Seoul (Korea, Republic of)] (and others)

2004-02-15

The objective of this research is to develop on efficient integrity evaluation technology and to investigate the applicability of the newly-developed technology such as internet-based cyber platform etc. to Nuclear Power Plant(NPP) components. The development of an efficient structural integrity evaluation system is necessary for safe operation of NPP as the increase of operating periods. Moreover, material test data as well as emerging structural integrity assessment technology are also needed for the evaluation of aged components. The following five topics are covered in this project: development of the wall-thinning evaluation program for nuclear piping; development of structural integrity evaluation criteria for steam generator tubes with cracks of various shape; development of fatigue life evaluation system for major components of NPP; ingegration of internet-based cyber platform and integrity evaluation program for primary components of NPP; effects of aging on strength of dissimilar welds.

Contributions of Science and Technology Parks Towards Firms' Performance in Pakistan

International Nuclear Information System (INIS)

Mangrio, W.B.; Naqvi, I.B.

2013-01-01

Several countries have adopted different strategies, models and policies to assist companies to develop their technological capabilities. These include high tech cluster development, creation of venture capital fund, establishment of technology incubation center, and Science and Technology parks. In turn, the creation of knowledge base industries, regional development, improves the technological infrastructure and life standard of the people. This paper discusses the contribution of science and technology parks in firms' performance in particularly employment, sales and profitability and also in creation of new businesses in information technology sector in Pakistan. This study is based on the case study of STPs (Software Technology Parks) of Islamabad. The results revealed that the establishment of STPs could be helpful in the creation of new companies as half of firms located at the STPs were startup enterprises. It helps firms to enhance its growth performance in the first five years after starting their business at these STPs. By developing software parks in three major cities, Pakistan Software Export Board have achieved partially its objectives. (author)

Development of life evaluation technology for nuclear power plant components

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Jin; Kim, Yun Jae; Choi, Jae Boong [Sungkyunkwan Univ., Seoul (Korea, Republic of)] (and others)

2002-03-15

This project focuses on developing reliable life evaluation technology for nuclear power plant components, and is divided into two parts, development of a life evaluation system for nuclear pressure vessels and evaluation of applicability of emerging technology to operating plants. For the development of life evaluation system for nuclear pressure vessels, the following seven topics are covered in this project: defect assessment method for steam generator tubes, development of fatigue monitoring system, assessment of corroded pipes, domestic round robin analysis for constructing P-T limit curve for RPV, development of probabilistic integrity assessment technique, effect of aging on strength of dissimilar welds, applicability of LBB to cast stainless steel, and development of probabilistic piping fracture mechanics.

U.S. ENVIRONMENTAL PROTECTION AGENCY (EPA) ENVIRONMENTAL TECHNOLOGY VERIFICATION (ETV) PROGRAM: ARSENIC MONITORING TECHNOLOGIES

Science.gov (United States)

The U.S. Environmental Protection Agency Environmental Technology Verification (ETV) program evaluates the performance of innovative air, water, pollution prevention and monitoring technologies that have the potential to improve human health and the environment. This technology ...

Technology certification and technology acceptance: Promoting interstate cooperation and market development for innovative technologies

International Nuclear Information System (INIS)

Brockbank, B.R.

1995-03-01

In the past two years, public and private efforts to promote development and deployment of innovative environmental technologies have shifted from the analysis of barriers to the implementation of a variety of initiatives aimed at surmounting those barriers. Particular attention has been directed at (1) streamlining fragmented technology acceptance processes within and among the states, and (2) alleviating disincentives, created by inadequate or unverified technology cost and performance data, for users and regulators to choose innovative technologies. Market fragmentation currently imposes significant cost burdens on technology developers and inhibits the investment of private capital in environmental technology companies. Among the responses to these problems are state and federal technology certification/validation programs, efforts to standardize cost/performance data reporting, and initiatives aimed at promoting interstate cooperation in technology testing and evaluation. This paper reviews the current status of these initiatives, identifies critical challenges to their success, and recommends strategies for addressing those challenges

Intervention of drudgery reducing technologies in agriculture and impact evaluation.

Science.gov (United States)

Mehta, Manju; Gandhi, Sudesh; Dilbaghi, Mamta

2012-01-01

Agriculture is main source of livelihood for majority of the population in India. Agriculture has been established as one of the drudgery prone occupation of unorganized sector due to lack of access to improved agricultural technologies. The present study was planned to assess intervention of drudgery reducing technologies in agriculture and its impact evaluation. The drudgery areas/activities in agriculture were identified. Participatory field level skill training for proper use of the ergonomically improved farm technologies were given to men and women in separate groups. An intervention package consisting of improved sickle, wheel hand hoe, capron, cot bag and protective gloves was introduced in village Shahpur. Data were collected to quantify the impact of intervention on the level of drudgery of worker before and after the technology intervention from sample of 30 respondents (15 male and 15 female) selected randomly from village Shahpur. Gain in knowledge and change in awareness level were calculated after the training.Evaluation of field validation of technology on drudgery of men & women was done after its use in the field conditions. A significant gain in awareness was observed among both men(2.6) & women (3.0) whereas the gain in knowledge was more among men (6.6) than women (4.5). In evaluation of field validation of technology on drudgery it was found that all the five technologies reduced the drudgery of men as well as women. However wheel hand hoe was used successfully by men in comparison to women who preferred to use their conventional technology i.e improved long-handled hoe. Evaluation of validation trials of the technologies reported that improved sickle was used successfully by both men & women farmers. More than half of the men farmers (53.3%) & only 13.3 percent women farmers preferred the wheel hand hoe over the traditional one as they found it four times more efficient in terms of time, energy & money saving. Cot bag was preferred by the

Performance of ultraviolet photocatalytic oxidation for indoor air applications: Systematic experimental evaluation

Energy Technology Data Exchange (ETDEWEB)

Zhong, Lexuan [Department of Building, Civil and Environmental Engineering, Concordia University, Montreal, Quebec H3G 1M8 (Canada); Haghighat, Fariborz, E-mail: fariborz.haghighat@concordia.ca [Department of Building, Civil and Environmental Engineering, Concordia University, Montreal, Quebec H3G 1M8 (Canada); Lee, Chang-Seo [Department of Building, Civil and Environmental Engineering, Concordia University, Montreal, Quebec H3G 1M8 (Canada); Lakdawala, Ness [DECTRON International Inc., Montreal, Quebec (Canada)

2013-10-15

Highlights: • An innovative experimental set-up was designed and constructed for testing UV-PCO. • Test methodologies were developed to examine UV-PCO air cleaners for VOCs removal. • VOCs type, inlet concentration, flow rate, irradiance, and RH have influence on PCO. • Gas-phase ozonation with a variety of compounds was examined in a duct system. • Formation of by-products generated from incomplete conversion was investigated. -- Abstract: Photocatalytic oxidation (PCO) is a promising technology that has potential to be applied in mechanically ventilated buildings to improve indoor air quality (IAQ). However, the major research studies were done in bench-top scale reactors under ideal reaction conditions. In addition, no study has been carried out on the investigation of the ozonation and photolysis effect using a pilot duct system. The objective of this study is the development of methodologies to evaluate the performance of PCO systems. A systematic parametric evaluation of the effects of various kinetic parameters, such as compound's type, inlet concentration, airflow rate, light intensity, and relative humidity, was conducted, and new interpretations were provided from a fundamental analysis. In addition, the photolysis effect under vacuum ultraviolet (VUV) irradiation for a variety of volatile organic compounds (VOCs) was examined for the first time in a pilot duct system. The performance comparison of ultraviolet C (UVC)-PCO and VUV-PCO was also discussed due to the presence of ozone. Moreover, the formation of by-products generated with or without ozone generation was fully compared to evaluate the PCO technology.

Performance of ultraviolet photocatalytic oxidation for indoor air applications: Systematic experimental evaluation

International Nuclear Information System (INIS)

Zhong, Lexuan; Haghighat, Fariborz; Lee, Chang-Seo; Lakdawala, Ness

2013-01-01

Highlights: • An innovative experimental set-up was designed and constructed for testing UV-PCO. • Test methodologies were developed to examine UV-PCO air cleaners for VOCs removal. • VOCs type, inlet concentration, flow rate, irradiance, and RH have influence on PCO. • Gas-phase ozonation with a variety of compounds was examined in a duct system. • Formation of by-products generated from incomplete conversion was investigated. -- Abstract: Photocatalytic oxidation (PCO) is a promising technology that has potential to be applied in mechanically ventilated buildings to improve indoor air quality (IAQ). However, the major research studies were done in bench-top scale reactors under ideal reaction conditions. In addition, no study has been carried out on the investigation of the ozonation and photolysis effect using a pilot duct system. The objective of this study is the development of methodologies to evaluate the performance of PCO systems. A systematic parametric evaluation of the effects of various kinetic parameters, such as compound's type, inlet concentration, airflow rate, light intensity, and relative humidity, was conducted, and new interpretations were provided from a fundamental analysis. In addition, the photolysis effect under vacuum ultraviolet (VUV) irradiation for a variety of volatile organic compounds (VOCs) was examined for the first time in a pilot duct system. The performance comparison of ultraviolet C (UVC)-PCO and VUV-PCO was also discussed due to the presence of ozone. Moreover, the formation of by-products generated with or without ozone generation was fully compared to evaluate the PCO technology

Review and evaluation of alternative chemical disposal technologies

National Research Council Canada - National Science Library

National Research Council Staff; Commission on Engineering and Technical Systems; Division on Engineering and Physical Sciences; National Research Council; National Academy of Sciences

.... In light of the fact that alternative technologies have evolved since the 1994 study, this new volume evaluates five Army-chosen alternatives to the baseline incineration system for the disposal...

PERFORMANCE MANAGEMENT APPROACHES IN ECONOMIC ORGANIZATIONS USING INFORMATION TECHNOLOGY

Directory of Open Access Journals (Sweden)

Anca Mehedintu

2012-03-01

Full Text Available Performance management includes activities that ensure that goals are consistently being met inan effective and efficient manner. Performance management can focus on the performance of an organization, adepartment, employee, or even the processes to build a product or service, as well as many other areas.In these days of globalization and intensive use of information technology, the organizations must defineand implement an appropriate strategy that would support their medium-term development, stability andcompetitiveness. This is achieved through a coherent and interrelated set of activities for understanding thecustomer expectations and the level at which the offer of organization add value to customers and satisfy theirneeds, define their internal organization to allow timely response to market demands without losing focus on client,tracking strategy and business model for the accomplishment of the organization mission, aligning the existing ITproject management or under development implementation in organization with the strategic management oforganization etc. Strategic Management determines the improvement of processes, effective use of resources, focuson critical areas in terms of finance, creating opportunities for innovation and technological progress, improvementof the supply mechanism and the duty to promote personal interaction and negotiation at all levels, continuousassessment of organization and its technological trends, analyze the market potential and competence field etc.Strategic management system will not give good results if the strategy is not defined by a set of operationalobjectives clearly at all levels.Business performance is based on a set of analytical processes of business, supported by informationtechnology that defines the strategic goals that can be measured by performance indicators. EnterprisePerformance Management creates a powerful and precise environment, characterized by data consistency,efficiency analysis

Importance Performance Analysis as a Trade Show Performance Evaluation and Benchmarking Tool

OpenAIRE

Tafesse, Wondwesen; Skallerud, Kåre; Korneliussen, Tor

2010-01-01

Author's accepted version (post-print). The purpose of this study is to introduce importance performance analysis as a trade show performance evaluation and benchmarking tool. Importance performance analysis considers exhibitors’ performance expectation and perceived performance in unison to evaluate and benchmark trade show performance. The present study uses data obtained from exhibitors of an international trade show to demonstrate how importance performance analysis can be used to eval...

Minimum detectable gas concentration performance evaluation method for gas leak infrared imaging detection systems.

Science.gov (United States)

Zhang, Xu; Jin, Weiqi; Li, Jiakun; Wang, Xia; Li, Shuo

2017-04-01

Thermal imaging technology is an effective means of detecting hazardous gas leaks. Much attention has been paid to evaluation of the performance of gas leak infrared imaging detection systems due to several potential applications. The minimum resolvable temperature difference (MRTD) and the minimum detectable temperature difference (MDTD) are commonly used as the main indicators of thermal imaging system performance. This paper establishes a minimum detectable gas concentration (MDGC) performance evaluation model based on the definition and derivation of MDTD. We proposed the direct calculation and equivalent calculation method of MDGC based on the MDTD measurement system. We build an experimental MDGC measurement system, which indicates the MDGC model can describe the detection performance of a thermal imaging system to typical gases. The direct calculation, equivalent calculation, and direct measurement results are consistent. The MDGC and the minimum resolvable gas concentration (MRGC) model can effectively describe the performance of "detection" and "spatial detail resolution" of thermal imaging systems to gas leak, respectively, and constitute the main performance indicators of gas leak detection systems.

Conductor gestures influence evaluations of ensemble performance

Directory of Open Access Journals (Sweden)

Steven eMorrison

2014-07-01

Full Text Available Previous research has found that listener evaluations of ensemble performances vary depending on the expressivity of the conductor’s gestures, even when performances are otherwise identical. It was the purpose of the present study to test whether this effect of visual information was evident in the evaluation of specific aspects of ensemble performance, articulation and dynamics. We constructed a set of 32 music performances that combined auditory and visual information and were designed to feature a high degree of contrast along one of two target characteristics: articulation and dynamics. We paired each of four music excerpts recorded by a chamber ensemble in both a high- and low-contrast condition with video of four conductors demonstrating high- and low-contrast gesture specifically appropriate to either articulation or dynamics. Using one of two equivalent test forms, college music majors and nonmajors (N = 285 viewed sixteen 30-second performances and evaluated the quality of the ensemble’s articulation, dynamics, technique and tempo along with overall expressivity. Results showed significantly higher evaluations for performances featuring high rather than low conducting expressivity regardless of the ensemble’s performance quality. Evaluations for both articulation and dynamics were strongly and positively correlated with evaluations of overall ensemble expressivity.

Performance Evaluation for Sustainability of Strong Smart Grid by Using Stochastic AHP and Fuzzy TOPSIS Methods

Directory of Open Access Journals (Sweden)

Huiru Zhao

2016-01-01

Full Text Available As an efficient way to deal with the global climate change and energy shortage problems, a strong, self-healing, compatible, economic and integrative smart gird is under construction in China, which is supported by large amounts of investments and advanced technologies. To promote the construction, operation and sustainable development of Strong Smart Grid (SSG, a novel hybrid framework for evaluating the performance of SSG is proposed from the perspective of sustainability. Based on a literature review, experts’ opinions and the technical characteristics of SSG, the evaluation model involves four sustainability criteria defined as economy, society, environment and technology aspects associated with 12 sub-criteria. Considering the ambiguity and vagueness of the subjective judgments on sub-criteria, fuzzy TOPSIS method is employed to evaluate the performance of SSG. In addition, different from previous research, this paper adopts the stochastic Analytical Hierarchy Process (AHP method to upgrade the traditional Technique for Order Preference by Similarity to Ideal Solution (TOPSIS by addressing the fuzzy and stochastic factors within weights calculation. Finally, four regional smart grids in China are ranked by employing the proposed framework. The results show that the sub-criteria affiliated with environment obtain much more attention than that of economy from experts group. Moreover, the sensitivity analysis indicates the ranking list remains stable no matter how sub-criteria weights are changed, which verifies the robustness and effectiveness of the proposed model and evaluation results. This study provides a comprehensive and effective method for performance evaluation of SSG and also innovates the weights calculation for traditional TOPSIS.

Performance evaluations of continuous glucose monitoring systems: precision absolute relative deviation is part of the assessment.

Science.gov (United States)

Obermaier, Karin; Schmelzeisen-Redeker, Günther; Schoemaker, Michael; Klötzer, Hans-Martin; Kirchsteiger, Harald; Eikmeier, Heino; del Re, Luigi

2013-07-01

Even though a Clinical and Laboratory Standards Institute proposal exists on the design of studies and performance criteria for continuous glucose monitoring (CGM) systems, it has not yet led to a consistent evaluation of different systems, as no consensus has been reached on the reference method to evaluate them or on acceptance levels. As a consequence, performance assessment of CGM systems tends to be inconclusive, and a comparison of the outcome of different studies is difficult. Published information and available data (as presented in this issue of Journal of Diabetes Science and Technology by Freckmann and coauthors) are used to assess the suitability of several frequently used methods [International Organization for Standardization, continuous glucose error grid analysis, mean absolute relative deviation (MARD), precision absolute relative deviation (PARD)] when assessing performance of CGM systems in terms of accuracy and precision. The combined use of MARD and PARD seems to allow for better characterization of sensor performance. The use of different quantities for calibration and evaluation, e.g., capillary blood using a blood glucose (BG) meter versus venous blood using a laboratory measurement, introduces an additional error source. Using BG values measured in more or less large intervals as the only reference leads to a significant loss of information in comparison with the continuous sensor signal and possibly to an erroneous estimation of sensor performance during swings. Both can be improved using data from two identical CGM sensors worn by the same patient in parallel. Evaluation of CGM performance studies should follow an identical study design, including sufficient swings in glycemia. At least a part of the study participants should wear two identical CGM sensors in parallel. All data available should be used for evaluation, both by MARD and PARD, a good PARD value being a precondition to trust a good MARD value. Results should be analyzed and

High-performance silicon photonics technology for telecommunications applications.

Science.gov (United States)

Yamada, Koji; Tsuchizawa, Tai; Nishi, Hidetaka; Kou, Rai; Hiraki, Tatsurou; Takeda, Kotaro; Fukuda, Hiroshi; Ishikawa, Yasuhiko; Wada, Kazumi; Yamamoto, Tsuyoshi

2014-04-01

By way of a brief review of Si photonics technology, we show that significant improvements in device performance are necessary for practical telecommunications applications. In order to improve device performance in Si photonics, we have developed a Si-Ge-silica monolithic integration platform, on which compact Si-Ge-based modulators/detectors and silica-based high-performance wavelength filters are monolithically integrated. The platform features low-temperature silica film deposition, which cannot damage Si-Ge-based active devices. Using this platform, we have developed various integrated photonic devices for broadband telecommunications applications.

High-performance silicon photonics technology for telecommunications applications

International Nuclear Information System (INIS)

Yamada, Koji; Tsuchizawa, Tai; Nishi, Hidetaka; Kou, Rai; Hiraki, Tatsurou; Takeda, Kotaro; Fukuda, Hiroshi; Yamamoto, Tsuyoshi; Ishikawa, Yasuhiko; Wada, Kazumi

2014-01-01

By way of a brief review of Si photonics technology, we show that significant improvements in device performance are necessary for practical telecommunications applications. In order to improve device performance in Si photonics, we have developed a Si-Ge-silica monolithic integration platform, on which compact Si-Ge–based modulators/detectors and silica-based high-performance wavelength filters are monolithically integrated. The platform features low-temperature silica film deposition, which cannot damage Si-Ge–based active devices. Using this platform, we have developed various integrated photonic devices for broadband telecommunications applications. (review)

High-performance silicon photonics technology for telecommunications applications

Science.gov (United States)

Yamada, Koji; Tsuchizawa, Tai; Nishi, Hidetaka; Kou, Rai; Hiraki, Tatsurou; Takeda, Kotaro; Fukuda, Hiroshi; Ishikawa, Yasuhiko; Wada, Kazumi; Yamamoto, Tsuyoshi

2014-04-01

By way of a brief review of Si photonics technology, we show that significant improvements in device performance are necessary for practical telecommunications applications. In order to improve device performance in Si photonics, we have developed a Si-Ge-silica monolithic integration platform, on which compact Si-Ge-based modulators/detectors and silica-based high-performance wavelength filters are monolithically integrated. The platform features low-temperature silica film deposition, which cannot damage Si-Ge-based active devices. Using this platform, we have developed various integrated photonic devices for broadband telecommunications applications.

Healthy China 2020 : Policy and Technology Evaluation | IDRC ...

International Development Research Centre (IDRC) Digital Library (Canada)

Healthy China 2020 : Policy and Technology Evaluation ... aimed at providing a blueprint for universal basic healthcare coverage for all by 2020. ... Implementing clinical pathway management and reforming compensation mechanism in rural ...

Evaluation of solar electric propulsion technologies for discovery class missions

Science.gov (United States)

Oh, David Y.

2005-01-01

A detailed study examines the potential benefits that advanced electric propulsion (EP) technologies offer to the cost-capped missions in NASA's Discovery program. The study looks at potential cost and performance benefits provided by three EP technologies that are currently in development: NASA's Evolutionary Xenon Thruster (NEXT), an Enhanced NSTAR system, and a Low Power Hall effect thruster. These systems are analyzed on three straw man Discovery class missions and their performance is compared to a state of the art system using the NSTAR ion thruster. An electric propulsion subsystem cost model is used to conduct a cost-benefit analysis for each option. The results show that each proposed technology offers a different degree of performance and/or cost benefit for Discovery class missions.

48 CFR 3052.216-72 - Performance evaluation plan.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Performance evaluation... CONTRACT CLAUSES Text of Provisions and Clauses 3052.216-72 Performance evaluation plan. As prescribed in... Evaluation Plan (DEC 2003) (a) A Performance Evaluation Plan shall be unilaterally established by the...

Development of Nano technology in High Performance Concrete

International Nuclear Information System (INIS)

Nima Farzadnia; Abang Abdullah Abang Ali; Ramazan Demirboga; Demirboga, R.

2011-01-01

Concrete is the most widely used building material all around the world which has been undergoing many changes aligned with technological advancement. The most recent available type of concrete is high performance concrete which is produced by employing different admixtures both chemical and mineral to enhance mechanical properties and durability. Recently, technology has made it easy for scientist to study nano sized admixtures and their effect on microstructure of concrete. This paper reviews nano particles in cement composites and how they can improve different properties of concrete. (author)

Development of 4S and related technologies. (3) Statistical evaluation of safety performance of 4S on ULOF event

International Nuclear Information System (INIS)

Ishii, Kyoko; Matsumiya, Hisato; Horie, Hideki; Miyagi, Kazumi

2009-01-01

The purpose of this work is to evaluate quantitatively and statistically the safety performance of Super-Safe, Small, and Simple reactor (4S) by analyzing with ARGO code, a plant dynamics code for a sodium-cooled fast reactor. In this evaluation, an Anticipated Transient Without Scram (ATWS) is assumed, and an Unprotected Loss of Flow (ULOF) event is selected as a typical ATWS case. After a metric concerned with safety design is defined as performance factor a Phenomena Identification Ranking Table (PIRT) is produced in order to select the plausible phenomena that affect the metric. Then a sensitivity analysis is performed for the parameters related to the selected plausible phenomena. Finally the metric is evaluated with statistical methods whether it satisfies the given safety acceptance criteria. The result is as follows: The Cumulative Damage Fraction (CDF) for the cladding is defined as a metric, and the statistical estimation of the one-sided upper tolerance limit of 95 percent probability at a 95 percent confidence level in CDF is within the safety acceptance criterion; CDF < 0.1. The result shows that the 4S safety performance is acceptable in the ULOF event. (author)

40 CFR 35.515 - Evaluation of performance.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Evaluation of performance. 35.515 Section 35.515 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL....515 Evaluation of performance. (a) Joint evaluation process. The applicant and the Regional...

Sustainability Of Electricity Supply Technologies under German Conditions: A Comparative Evaluation

International Nuclear Information System (INIS)

Hirschberg, S; Dones, R.; Heck, T.; Burgherr, P.; Schenler, W.; Bauer, C.

2004-12-01

On behalf of the International Committee on Nuclear Technology (ILK) the Paul Scherrer Institut carried out a comparative study addressing the sustainability of electricity supply technologies operating under German-specific conditions. The general objective of this analysis was to provide a support for the formulation of ILK position on the sustainability of various electricity supply technologies, with special emphasis on nuclear energy. The evaluation covers selected current fossil, nuclear and renewable technologies, which are representative for the average conditions in Germany. Two methods of indicator aggregation were employed, i.e. estimation of total (internal and extemal) costs and Multi-criteria Decision Analysis (MCDA). Use of MCDA is motivated by acknowledgement of the role of value judgements in decision-making. Both total costs and MCDA-based technology-specific total scores are useful comparative indicators of sustainability. Sustainability perspective implies a balanced (equal) importance assignment to economic, ecological and social aspects. In summary, this study provides a framework for systematic evaluation of sustainability of energy systems. Refinements of the methodology and specific indicators are feasible. Options for future applications include direct involvement of stakeholders, and evaluations of future technologies and of supply scenarios combining the various candidate technologies. Tools supporting such analyses have been developed by PSI and can be adjusted to the needs of country-specific applications. (author)

Assistive Technology for Persons with Physical Disabilities: Evaluation and Outcomes

NARCIS (Netherlands)

Rigby, P.J.

2009-01-01

This thesis presents a compilation of published studies that evaluated assistive technology interventions for children and adults with physical disabilities. The first chapter introduces the need for and the challenges involved in studying the outcomes of assistive technology interventions. The

A Survey on the HFE-related Technologies for the Improvements of Human Performance of Safety Personnel in Rail System

International Nuclear Information System (INIS)

Koo, I. S.; Park, G. O.; Suh, S. M.; Sim, Y. R.; Go, J. H.; Jeong, J. H.; Son, C. H.

2005-08-01