A Study of Torque Vectoring and Traction Control for an All-Wheel Drive Electric Vehicle

Directory of Open Access Journals (Sweden)

Maharun Mui’nuddin

2014-07-01

Full Text Available Common vehicle always experience energy loss during cornering manoeuver. Thus, to ensure it did not happened especially at high speed, a study of torque vectoring and traction control need to be made since it can increase the traction control of tyres during cornering at high speed. The study of torque vectoring and traction control for an all-wheel drive electric vehicle was conducted by modelling an all-wheel drive electric vehicle (EV in ADAMS/Car software. In addition, an optimal control algorithm will be developed for best performance to minimize energy losses using MATLAB/Simulink software. Furthermore, to prove the effectiveness of the all-wheel drive electric, the torque and traction control simulation of the all-wheel drive electric vehicle will be compared with uncontrolled electric vehicle model. According to the result, torque vectoring and traction control of in-wheel motor in all wheel drive EV can help to increase the performance of the electric vehicle during cornering manoeuver. In conclusion, this study of torque vectoring and traction control for an all-wheel drive electric vehicle will help researchers to improve the design of the future electric vehicle in term of the vehicle performance during cornering manoeuvre.

On state estimation in electric drives

International Nuclear Information System (INIS)

Leon, A.E.; Solsona, J.A.

2010-01-01

This paper deals with state estimation in electric drives. On one hand a nonlinear observer is designed, whereas on the other hand the speed state is estimated by using the dirty derivative from the position measured. The dirty derivative is an approximate version of the perfect derivative which introduces an estimation error few times analyzed in drive applications. For this reason, our proposal in this work consists in illustrating several aspects on the performance of the dirty derivator in presence of both model uncertainties and noisy measurements. To this end, a case study is introduced. The case study considers rotor speed estimation in a permanent magnet stepper motor, by assuming that rotor position and electrical variables are measured. In addition, this paper presents comments about the connection between dirty derivators and observers, and advantages and disadvantages of both techniques are also remarked.

Chaos in electric drive systems analysis control and application

CERN Document Server

Chau, K T

2011-01-01

In Chaos in Electric Drive Systems: Analysis, Control and Application authors Chau and Wang systematically introduce an emerging technology of electrical engineering that bridges abstract chaos theory and practical electric drives. The authors consolidate all important information in this interdisciplinary technology, including the fundamental concepts, mathematical modeling, theoretical analysis, computer simulation, and hardware implementation. The book provides comprehensive coverage of chaos in electric drive systems with three main parts: analysis, control and application. Corresponding drive systems range from the simplest to the latest types: DC, induction, synchronous reluctance, switched reluctance, and permanent magnet brushless drives.The first book to comprehensively treat chaos in electric drive systemsReviews chaos in various electrical engineering technologies and drive systemsPresents innovative approaches to stabilize and stimulate chaos in typical drivesDiscusses practical application of cha...

[Effect of air-electric fields on driving and reaction patterns. Test subjects in the car driving simulator (author's transl)].

Science.gov (United States)

Anselm, D; Danner, M; Kirmaier, N; König, H L; Müller-Limmroth, W; Reis, A; Schauerte, W

1977-06-10

In the relevant frequency range of about 10 Hertz cars can be considered very largely as Faraday cages and consequently as screens against air-electric fields. This may have a negative influence on driving and reaction patterns as a result. In an extensive investigation 48 subjects in a driving simulator were exposed to definite artificially produced air-electric fields. The self-rating of the performance and concentration of the subjects, reaction times and driving errors were determined. While the reaction times remained practically constant, the driving behavior of the subjects improved.

Study of Driving Fatigue Alleviation by Transcutaneous Acupoints Electrical Stimulations

Directory of Open Access Journals (Sweden)

Fuwang Wang

2014-01-01

Full Text Available Driving fatigue is more likely to bring serious safety trouble to traffic. Therefore, accurately and rapidly detecting driving fatigue state and alleviating fatigue are particularly important. In the present work, the electrical stimulation method stimulating the Láogóng point (劳宫PC8 of human body is proposed, which is used to alleviate the mental fatigue of drivers. The wavelet packet decomposition (WPD is used to extract θ, α, and β subbands of drivers’ electroencephalogram (EEG signals. Performances of the two algorithms (θ+α/(α+β and θ/β are also assessed as possible indicators for fatigue detection. Finally, the differences between the drivers with electrical stimulation and normal driving are discussed. It is shown that stimulating the Láogóng point (劳宫PC8 using electrical stimulation method can alleviate driver fatigue effectively during longtime driving.

Multidisciplinary design of electrical drives

Energy Technology Data Exchange (ETDEWEB)

Blaabjerg, F.; Rasmussen, P.O.; Pedersen, J.K.

1999-07-01

Traditionally, simulation tools for drives can simulate electrical parameters, torque and different loads. Those parameters are in many cases appropriate. However, power electronics in drives will also influence on torque ripple, temperature, vibration and acoustical noise from the motor and it is necessary to include those phenomena in the next generation of simulation tools for electrical drives. This paper describes a new design program where acoustic noise of electromagnetic origin can be simulated and even be heard by the motor and drives designer. The design program is based on a simple vibrational/acoustic model where the parameters can be calculated based on the geometry of the motor. Examples of vibrational/acoustical modelling are included and verified in both time and frequency domain. Special emphasis is on the switched reluctance motor. (au)

Development of a Cooperative Braking System for Front-Wheel Drive Electric Vehicles

Directory of Open Access Journals (Sweden)

Di Zhao

2018-02-01

Full Text Available Most electric vehicles adopt cooperative braking systems that can blend friction braking torque with regenerative braking torque to achieve higher energy efficiency while maintaining a certain braking performance and driving safety. This paper presented a new cooperative regenerative braking system that contained a fully-decoupled hydraulic braking mechanism based on a modified electric stability control system. The pressure control algorithm and brake force distribution strategy were also discussed. Dynamic models of a front wheel drive electric car equipped with this system and a simulation platform with a driver model and driving cycles were established. Tests to evaluate the braking performance and energy regeneration were simulated and analyzed on this platform and the simulation results showed the feasibility and effectiveness of this system.

Optimal control strategy design for extending all-electric driving capability of plug-in hybrid electric vehicles (PHEVs)

Energy Technology Data Exchange (ETDEWEB)

Williamson, S.S [Concordia Univ., Montreal, PQ (Canada). Dept. of Electrical and Computer Engineering, P.D Ziogas Power Electronics Laboratory

2007-07-01

The high voltage energy storage system in plug-in hybrid electric vehicles (PHEVs) is usually a rechargeable type that service a dual purpose, notably to supplement the power delivered by the internal combustion engine, and to provide partial propulsion energy from an off-board source of electricity. The energy storage devices in electric vehicles typically improve vehicle efficiency through engine downsizing and by recapturing braking energy. However, since PHEVs have the ability to recharge their energy storage systems directly from the power grid, the periods of all-electric operation can be extended, thereby reducing the dependence on the internal combustion engine. This is particularly useful in city driving conditions. Developers of PHEV technology are faced with the challenge of choosing the appropriate energy storage battery in order to improve the all-electric drive range. In this study, control strategies were modeled for specific driving load conditions using the Advanced Vehicle Simulator (ADVISOR) software. This paper presented specific control algorithms for PHEV operation for various city driving loads. The optimal design strategy considered the improvement of critical energy storage parameters, overall drive train efficiency, and vehicle performance characteristics. Future trends in the design and development of PHEV drive trains were also presented. 13 figs.

Optimization of parameters of special asynchronous electric drives

Science.gov (United States)

Karandey, V. Yu; Popov, B. K.; Popova, O. B.; Afanasyev, V. L.

2018-03-01

The article considers the solution of the problem of parameters optimization of special asynchronous electric drives. The solution of the problem will allow one to project and create special asynchronous electric drives for various industries. The created types of electric drives will have optimum mass-dimensional and power parameters. It will allow one to realize and fulfill the set characteristics of management of technological processes with optimum level of expenses of electric energy, time of completing the process or other set parameters. The received decision allows one not only to solve a certain optimizing problem, but also to construct dependences between the optimized parameters of special asynchronous electric drives, for example, with the change of power, current in a winding of the stator or rotor, induction in a gap or steel of magnetic conductors and other parameters. On the constructed dependences, it is possible to choose necessary optimum values of parameters of special asynchronous electric drives and their components without carrying out repeated calculations.

MODELING CONTROLLED ASYNCHRONOUS ELECTRIC DRIVES WITH MATCHING REDUCERS AND TRANSFORMERS

Directory of Open Access Journals (Sweden)

V. S. Petrushin

2015-04-01

Full Text Available Purpose. Working out of mathematical models of the speed-controlled induction electric drives ensuring joint consideration of transformers, motors and loadings, and also matching reducers and transformers, both in static, and in dynamic regimes for the analysis of their operating characteristics. Methodology. At mathematical modelling are considered functional, mass, dimensional and cost indexes of reducers and transformers that allows observing engineering and economic aspects of speed-controlled induction electric drives. The mathematical models used for examination of the transitive electromagnetic and electromechanical processes, are grounded on systems of nonlinear differential equations with nonlinear coefficients (parameters of equivalent circuits of motors, varying in each operating point, including owing to appearances of saturation of magnetic system and current displacement in a winding of a rotor of an induction motor. For the purpose of raise of level of adequacy of models a magnetic circuit iron, additional and mechanical losses are considered. Results. Modelling of the several speed-controlled induction electric drives, different by components, but working on a loading equal on character, magnitude and a demanded control range is executed. At use of characteristic families including mechanical, at various parameters of regulating on which performances of the load mechanism are superimposed, the adjusting characteristics representing dependences of a modification of electrical, energy and thermal magnitudes from an angular speed of motors are gained. Originality. The offered complex models of speed-controlled induction electric drives with matching reducers and transformers, give the chance to realize well-founded sampling of components of drives. They also can be used as the design models by working out of speed-controlled induction motors. Practical value. Operating characteristics of various speed-controlled induction electric

Blow molding electric drives of Mechanical Engineering

Science.gov (United States)

Bukhanov, S. S.; Ramazanov, M. A.; Tsirkunenko, A. T.

2018-03-01

The article considers the questions about the analysis of new possibilities, which gives the use of adjustable electric drives for blowing mechanisms of plastic production. Thus, the use of new semiconductor converters makes it possible not only to compensate the instability of the supply network by using special dynamic voltage regulators, but to improve (correct) the power factor. The calculation of economic efficiency in controlled electric drives of blowing mechanisms is given. On the basis of statistical analysis, the calculation of the reliability parameters of the regulated electric drives’ elements under consideration is given. It is shown that an increase in the reliability of adjustable electric drives is possible both due to overestimation of the electric drive’s installed power, and in simpler schemes with pulse-vector control.

Digital control of electric drives

CERN Document Server

Koziol, R; Szklarski, L

1992-01-01

The electromechanical systems employed in different branches of industry are utilized most often as drives of working machines which must be fed with electric energy in a continuous, periodic or even discrete way. Some of these machines operate at constant speed, others require wide and varying energy control. In many designs the synchronous cooperation of several electric drives is required in addition to the desired dynamic properties. For these reasons the control of the cooperation and dynamics of electromechanical systems requires the use of computers.This book adopts an unusual approach

Electric Drive Study

Science.gov (United States)

1987-03-01

compound promises to reduce weight of future permanent magnet motors by 20 to 30 percent; a similar reduction is expected in size (approximately 20...drive systems. The AC permanent magnet (brushless DC motor) is rapidly evolving and will replace most electrically excited machines. Permanent magnet motors using

Simulating Study on Drive System Performance for Hybrid Electric Bus Based on ADVISOR

Directory of Open Access Journals (Sweden)

Wang Xingxing

2017-01-01

Full Text Available Hybrid electric bus has a number of advantages when compared with ordinary passenger cars, but in the dynamic matching and the vehicle performance are difficult to detect, thus limits its development process. In this paper, combined with the actual models, the hybrid electric bus module parameters were modified in the software of ADVISOR (Advanced Vehicle Simulator, main including: module of the vehicle, the wheel module, motor module, a battery module and engine module, three kinds of bus models for A, B and C were established, and the related performance that need to be analyzed was set up, such as acceleration, gradability, emissions and energy utilization and so on, in order to ensure the vehicle running in the same environment and convenient for comparison, a fixed vehicle driving cycles was chose, then the simulation results was analyzed, and the various performance was compared with the dynamic indicators and economic indicators which determined by referencing of traditional city bus standard and each other, and finally, the performance optimal model of B was chose out which can meet the demand, its related performance parameters of the simulation results are as follows: the best gradability is 26%, maximum speed is 72.7km/h, maximum acceleration is 1.7m/s2, 0~50km/h acceleration time is 9.5s and fuel consumption is 25L/km.

Electrical machines & drives

CERN Document Server

Hammond, P

1985-01-01

Containing approximately 200 problems (100 worked), the text covers a wide range of topics concerning electrical machines, placing particular emphasis upon electrical-machine drive applications. The theory is concisely reviewed and focuses on features common to all machine types. The problems are arranged in order of increasing levels of complexity and discussions of the solutions are included where appropriate to illustrate the engineering implications. This second edition includes an important new chapter on mathematical and computer simulation of machine systems and revised discussions o

Comparison of electric drives for road vehicles

Energy Technology Data Exchange (ETDEWEB)

Bader, C; Stephan, W [Deutsche Automobilgesellschaft m.b.H., Esslingen (Germany, F.R.)

1977-01-01

The low energy-storage capacity of the electrolytic energy-storage apparatus available at the moment limits the practical use of electric vehicles to meeting the requirements for restricted areas. But in this field of application, conversion from drive with internal combustion engine to electric drive can be considered only if a reduction of costs is achieved with electric drive. From the wide range of possible drive units the most suitable is found to be the dc squirrelcage motor the speed of which is controlled by field weakening. In the case of a motor with conventional design, the controllable drive range is limited to about 1 : 3, so that generally additional measures are required for extending the drive range. But if the motor is fitted with a compensation winding, field weakening to give a controlled speed range of 1 : 8 can be obtained. To evaluate the different drive units under consideration use is made of the acceleration when, according to the drive system, advantages are obtained from the point of view of energy consumption with disadvantages in acceleration time, and vice versa. By using vehicles proven in practice with different drive systems, either with hydrodynamic transducer and battery switchover, or else with changeover gear and mechanical clutch, the overall construction of the different control and protective arrangements are demonstrated. It is then found that the extra cost of regulation in the case of automatic drive operation is partly compensated by the additional protective devices which are required to limit the effects of any incorrect operations with a manually-operated drive.

At A Glance: Electric-Drive Vehicles

Energy Technology Data Exchange (ETDEWEB)

2016-07-01

Electric-drive vehicles use electricity as their primary fuel or to improve the efficiency of conventional vehicle designs. With the range of styles and options available, there is likely one to meet your needs. The vehicles can be divided into three categories: 1) Hybrid electric vehicles (HEVs), 2) Plug-in hybrid electric vehicles (PHEVs), and 3) All-electric vehicles (EVs).

At A Glance: Electric-Drive Vehicles

Energy Technology Data Exchange (ETDEWEB)

None

2016-07-13

Electric-drive vehicles use electricity as their primary fuel or to improve the efficiency of conventional vehicle designs. With the range of styles and options available, there is likely one to meet your needs. The vehicles can be divided into three categories: 1) Hybrid electric vehicles (HEVs), 2) Plug-in hybrid electric vehicles (PHEVs), and 3) All-electric vehicles (EVs).

Computer-Aided Engineering for Electric-Drive Vehicle Batteries (CAEBAT)

Science.gov (United States)

Consortium and Partners | Transportation Research | NREL Computer-Aided Engineering for Electric-Drive Vehicle Batteries (CAEBAT) Consortium and Partners Computer-Aided Engineering for Electric -Drive Vehicle Batteries (CAEBAT) Consortium and Partners The Computer-Aided Engineering for Electric

Does Driving Range of Electric Vehicles Influence Electric Vehicle Adoption?

Directory of Open Access Journals (Sweden)

Seiho Kim

2017-10-01

Full Text Available This study aims to determine the influential factors on the market share of electric vehicles through panel data analysis based on time series data from 2011 to 2015 in 31 countries. We selected five significant independent variables that are expected to affect electric vehicle adoption based on literature review. The econometric model in this study suggests that the relative price of electric vehicle compared to internal combustion engine vehicle, driving range, and number of models available in markets are correlated to the market share of electric vehicles. On the other hand, relationship between recharging infrastructure—an important factor for electric vehicle adoption in many studies—and market share of electric vehicles turned out to be insignificant in this study. From a political point of view, we argue that policy makers need to allocate more resources to research and development in order to extend driving range at the early stage of electric vehicle deployment in the markets.

Recent Research Results in the Field of Electric Drives and Mechatronics

Directory of Open Access Journals (Sweden)

Jan Vittek

2003-01-01

Full Text Available The paper presents an overview of research results achieved in the field of Electrical Drives and Mechatronics for the period of three years. The achieved outputs are formed into three individual parts. In the field of Electric Drives the most significant outputs have been achieved in the development of a new control algorithms for a.c. drives under general name 'Forced Dynamics Control' , in improvement of shaft sensorless control methods and in implementation of developed algorithms via digital signal processors. In the field of Electric Traction the most important results have been gained in optimization of power of traction vehicles andat development of diagnostic systems for evaluation of technical conditions of traction devices. In the field of Electric Machines the most important outputs have been achieved in the research of modern electronically commutated electrical machines, their performances in steady and transient states, new design method for their configuration and new methods for automatic parameters identification. In the end the list of the most important publications for all three parts is enclosed.

Advanced electric drives analysis, control, and modeling using MATLAB/Simulink

CERN Document Server

Mohan, Ned

2014-01-01

Advanced Electric Drives utilizes a physics-based approach to explain the fundamental concepts of modern electric drive control and its operation under dynamic conditions. Gives readers a "physical" picture of electric machines and drives without resorting to mathematical transformations for easy visualization Confirms the physics-based analysis of electric drives mathematically Provides readers with an analysis of electric machines in a way that can be easily interfaced to common power electronic converters and controlled using any control scheme Makes the MATLAB/Simulink files used in exampl

Electric accessory drives in automobiles. Elektrische Hilfsantriebe in Kraftfahrzeugen

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

Ten lectures were presented on the conference ''Electric accessory drives in automobiles'' subjects: - Survey on electric accessory drives in automobiles; cooperation of generator, battery and starter; technical solution of accessory drives, considerations on a system; comparison of various solutions for drives by viewing the example of a headlight vertical aim control; wiper motors and their control; blowers for heating, ventilation and air conditioning in automobiles; criteria for dimensioning of blower motors; drives in heating and air-conditioning applicances; permanent magnets for engine excitation; systematic quality assurance of electric accessory drives from car-development to serial production. Numerous illustrations and formulas are supplied which illustrate and explain the lectures. Each lecture is abstracted individually.

Thermal and Arc Flash Analysis of Electric Motor Drives in Distribution Networks

OpenAIRE

Nikolovski, Srete; Mlakić, Dragan; Alibašić, Emir

2017-01-01

The paper presents thermal analysis and arc flash analysis taking care of protection relays coordination settings for electric motor drives connected to the electrical network. Power flow analysis is performed to check if there are any voltage and loading violation conditions in the system. Fault analysis is performed to check the short circuit values and compute arc flash energy dissipated at industrial busbars to eliminate damage to electrical equipment and electrical shocks and hazard to p...

Relay protection features of frequency-adjustable electric drive

Science.gov (United States)

Kuprienko, V. V.

2018-03-01

The features of relay protection of high-voltage electric motors in composition of the frequency-adjustable electric drive are considered in the article. The influence of frequency converters on the stability of the operation of various types of relay protection used on electric motors is noted. Variants of circuits for connecting relay protection devices are suggested. The need to develop special relay protection devices for a frequency-adjustable electric drive is substantiated.

A novel dual motor drive system for three wheel electric vehicles

Science.gov (United States)

Panmuang, Piyapat; Thongsan, Taweesak; Suwapaet, Nuchida; Laohavanich, Juckamass; Photong, Chonlatee

2018-03-01

This paper presents a novel dual motor drive system used for three wheel electric vehicles that have one free wheel at the front and two wheels with a drive system at the end of the vehicles. A novel dual motor drive system consists of two identical DC motors that are independently controlled by its speed-torque controller. Under light load conditions, only one of the DC motors will operate around it rated whilst under hard load conditions both of the DC motors will operate. With this drive system, the motors will operate only at its high performance at rated or else no operate to retain longer lifetime. The simulated results for the Skylab three wheel electric vehicle prototype with 8kW at full load (high torque, low speed) and around 4kW at light/normal operating loads (regular speed-torque) showed that the proposed system provides better dynamic responses with faster overshoot current/voltage recovery time, has lower investment costs, has longer lifetime of the motors and allows the motors to always operate at their high performance and thus achieve more cost effective system compared to a single motor drive system with 8kW DC motors.

Optimal Control Development System for Electrical Drives

Directory of Open Access Journals (Sweden)

Marian GAICEANU

2008-08-01

Full Text Available In this paper the optimal electrical drive development system is presented. It consists of both electrical drive types: DC and AC. In order to implement the optimal control for AC drive system an Altivar 71 inverter, a Frato magnetic particle brake (as load, three-phase induction machine, and dSpace 1104 controller have been used. The on-line solution of the matrix Riccati differential equation (MRDE is computed by dSpace 1104 controller, based on the corresponding feedback signals, generating the optimal speed reference for the AC drive system. The optimal speed reference is tracked by Altivar 71 inverter, conducting to energy reduction in AC drive. The classical control (consisting of rotor field oriented control with PI controllers and the optimal one have been implemented by designing an adequate ControlDesk interface. The three-phase induction machine (IM is controlled at constant flux. Therefore, the linear dynamic mathematical model of the IM has been obtained. The optimal control law provides transient regimes with minimal energy consumption. The obtained solution by integration of the MRDE is orientated towards the numerical implementation-by using a zero order hold. The development system is very useful for researchers, doctoral students or experts training in electrical drive. The experimental results are shown.

THE ANALISYS OF RAILWAY MULTI MOTORS ELECTRICAL DRIVE DYNAMIC

Directory of Open Access Journals (Sweden)

V. I. Khilmon

2015-01-01

Full Text Available The importance of multi motors electrical traction drive dynamic analysis is denoted by its large application in electrical driving railway vehicles. In this paper an analysis is presented for two inducton motors traction drive with frequency inverter, vector control, and speed sensors of each electrical drive. The goal of this work is the analysis of two induction motors electrical drive, taking into account parametric perturbations and also a limited moment of wheel-rail adhesion, by laboratory study and simulation. Because of difference between motor’s parameters, it is necessary for parallel work to select motors with identical resistances and inductive winding. For this purpose the parametric identification method was used for each electrical drive, and also for two parallel motors. The result of identification was used in control setting.The  slippage  of  the  traction  drives  is  difficult  to  reproduce  in  laboratory;  therefore a mathematical modeling and simulation of mechanical part with a traction force restriction, specific for railway transport, were carried out. The suggested simulation is built with account of elastic deformations in kinetic chain, transforming traction force. The model permits to study a dynamic system in various circumstances.The results of laboratory investigations and simulation of dynamic regimes for two motor electrical drives are presented in this article. The results of analysis show, that a minimal difference between any parameters of two motors, parallel connected to convertor, is important for the slippage stability.

DIAGNOSTICS CONCEPTION OF ELECTRICAL DRIVE OF A HYBRID VEHICLE

Directory of Open Access Journals (Sweden)

Y. Borodenko

2012-01-01

Full Text Available Conceptual approach to creat the diagnostic system of the power elements of the electric drive of the hybrid vehicle has been considered. Approbation of the imitation model of electric drive with brushless DC electric motor as a diagnostic object has been carried out.

Development of a driving cycle to evaluate the energy economy of electric vehicles in urban areas

International Nuclear Information System (INIS)

Brady, John; O’Mahony, Margaret

2016-01-01

Highlights: • Development of a driving cycle to evaluate energy economy of electric vehicles. • Improves on existing driving cycles by using real world data from electric vehicles. • Driving data from different road types and traffic conditions included. - Abstract: Understanding real-world driving conditions in the form of driving cycles is instrumental in the design of efficient powertrains and energy storage systems for electric vehicles. In addition, driving cycles serve as a standardised measurement procedure for the certification of a vehicle’s fuel economy and driving range. They also facilitate the evaluation of the economic and lifecycle costs of emerging vehicular technologies. However, discrepancies between existing driving cycles and real-world driving conditions exist due to a number of factors such as insufficient data, inadequate driving cycle development methodologies and methods to assess the representativeness of developed driving cycles. The novel aspect of the work presented here is the use of real-world data from electric vehicles, over a six month period, to derive a driving cycle appropriate for their assessment. A stochastic and statistical methodology is used to develop and assess the representativeness of the driving cycle against a separate set of real world electric vehicle driving data and the developed cycle performs well in that comparison. Although direct comparisons with internal combustion engine driving cycles are not that informative or relevant due to the marked differences between how they and electric vehicles operate, some discussion around how the developed electric vehicle cycle relates to them is also included.

Determination of power and moment on shaft of special asynchronous electric drives

Science.gov (United States)

Karandey, V. Yu; Popov, B. K.; Popova, O. B.; Afanasyev, V. L.

2018-03-01

In the article, questions and tasks of determination of power and the moment on a shaft of special asynchronous electric drives are considered. Use of special asynchronous electric drives in mechanical engineering and other industries is relevant. The considered types of electric drives possess the improved mass-dimensional indicators in comparison with singleengine systems. Also these types of electric drives have constructive advantages; the improved characteristics allow one to realize the technological process. But creation and design of new electric drives demands adjustment of existing or development of new methods and approaches of calculation of parameters. Determination of power and the moment on a shaft of special asynchronous electric drives is the main objective during design of electric drives. This task has been solved based on a method of electromechanical transformation of energy.

Design Study for Controllable Electric Motor for Three Wheel Drive, In Wheel Mounting on Professional, Electric, Lawn Mower

DEFF Research Database (Denmark)

Lu, Kaiyuan

Design of a new generation of electric drive motor for professional lawnmowers forms the basic objective of this thesis. Modern drive concepts produces a growing demand for electrical machines featuring high torque density, and suitable for direct drive applications. Much attention is presently...... focused upon the transverse flux permanent magnet machine, which attracts great interests in electric and hybrid propulsion systems. This thesis deals with modelling, performance analysis, design, test and measurement of permanent magnet transverse flux machines (PMTFM). It is important to understand...... the main aspects that influence the behaviour of a PMTFM, as this may lead to improved designs of PMTFM or may reveal the limitations of the transverse flux technology. Generally, in PMTFM, the flux has a complex 3D pattern. Finite Element Method (FEM) needs to be used to analyse the magnetic field...

Optimal charging of electric drive vehicles in a market environment

DEFF Research Database (Denmark)

Kristoffersen, Trine Krogh; Capion, Karsten Emil; Meibom, Peter

2011-01-01

With a potential to facilitate the integration of renewable energy into the electricity system, electric drive vehicles may offer a considerable flexibility by allowing for charging and discharging when desired. This paper takes the perspective of an aggregator that manages the electricity market...... participation of a vehicle fleet and presents a framework for optimizing charging and discharging of the electric drive vehicles, given the driving patterns of the fleet and the variations in market prices of electricity. When the aggregator is a price-taker the optimization can be stated in terms of linear...... programming whereas a quadratic programming formulation is required when he/she has market power. A Danish case study illustrates the construction of representative driving patterns through clustering of survey data from Western Denmark and the prediction of electricity price variations through regression...

Dynamic motion stabilization for front-wheel drive in-wheel motor electric vehicles

Directory of Open Access Journals (Sweden)

Jia-Sheng Hu

2015-12-01

Full Text Available This article presents a new dynamic motion stabilization approach to front-wheel drive in-wheel motor electric vehicles. The approach includes functions such as traction control system, electronic differential system, and electronic stability control. The presented electric vehicle was endowed with anti-skid performance in longitudinal accelerated start; smooth turning with less tire scrubbing; and safe driving experience in two-dimensional steering. The analysis of the presented system is given in numerical derivations. For practical verifications, this article employed a hands-on electric vehicle named Corsa-electric vehicle to carry out the tests. The presented approach contains an integrated scheme which can achieve the mentioned functions in a single microprocessor. The experimental results demonstrated the effectiveness and feasibility of the presented methodology.

Electric driving. Evaluation of transitions based on system options

International Nuclear Information System (INIS)

Nagelhout, D.; Ros, J.P.M.

2009-01-01

Over the past years, electric driving has become more and more attractive because of the development of better batteries. Driving electric vehicles could drastically reduce CO2 emissions, especially if more electricity would be generated by using sustainable energy. As most passenger cars are not used at night, this is the ideal time for charging their batteries. This would be cost-effective because, at that time, there is a surplus of generating capacity, and wind energy could also be used more effectively. Moreover, consumers will be able to drive clean and quiet vehicles at costs that seem surmountable in the future. At least two obstacles still need to be overcome. The first of which is the current maximum range of electric vehicles of around a few hundred kilometres. The second obstacle is the need for a standardised European network of charging stations, and electrical outlets near residences and at commercial and public parking facilities. This report shows the challenges facing the government and the business community of utilising the benefits of electric driving and of overcoming the obstacles [nl

Electric motor drive unit, especially adjustment drive for vehicles

Energy Technology Data Exchange (ETDEWEB)

Litterst, P

1980-05-29

An electric motor drive unit, particularly an adjustment drive for vehicles with at least two parallel drive shafts is described, which is compact and saves space, and whose manufacturing costs are low compared with those of well-known drive units of this type. The drive unit contains a suitable number of magnet systems, preferably permanent magnet systems, whose pole axes are spaced and run parallel. The two pole magnet systems have diametrically opposite shell-shaped segments, to which the poles are fixed. In at least one magnet system the two segments are connected by diametrically opposite flat walls parallel to the pole axes to form a single magnetic circuit pole housing. The segments of at least one other magnet system are arranged on this pole housing so that one of these flat walls is a magnetically conducting, connecting component of the magnetic circuit of the other magnet system.

Driving range estimation for electric vehicles based on driving condition identification and forecast

Science.gov (United States)

Pan, Chaofeng; Dai, Wei; Chen, Liao; Chen, Long; Wang, Limei

2017-10-01

With the impact of serious environmental pollution in our cities combined with the ongoing depletion of oil resources, electric vehicles are becoming highly favored as means of transport. Not only for the advantage of low noise, but for their high energy efficiency and zero pollution. The Power battery is used as the energy source of electric vehicles. However, it does currently still have a few shortcomings, noticeably the low energy density, with high costs and short cycle life results in limited mileage compared with conventional passenger vehicles. There is great difference in vehicle energy consumption rate under different environment and driving conditions. Estimation error of current driving range is relatively large due to without considering the effects of environmental temperature and driving conditions. The development of a driving range estimation method will have a great impact on the electric vehicles. A new driving range estimation model based on the combination of driving cycle identification and prediction is proposed and investigated. This model can effectively eliminate mileage errors and has good convergence with added robustness. Initially the identification of the driving cycle is based on Kernel Principal Component feature parameters and fuzzy C referring to clustering algorithm. Secondly, a fuzzy rule between the characteristic parameters and energy consumption is established under MATLAB/Simulink environment. Furthermore the Markov algorithm and BP(Back Propagation) neural network method is utilized to predict the future driving conditions to improve the accuracy of the remaining range estimation. Finally, driving range estimation method is carried out under the ECE 15 condition by using the rotary drum test bench, and the experimental results are compared with the estimation results. Results now show that the proposed driving range estimation method can not only estimate the remaining mileage, but also eliminate the fluctuation of the

Analysis of the Fuel Efficiency of a Hybrid Electric Drive with an Electric Power Splitter

Directory of Open Access Journals (Sweden)

D. Čundev

2008-01-01

Full Text Available This paper presents the results of an analysis of the fuel efficiency of a hybrid electric car drive, with an electric power splitter based on a double rotor synchronous permanent magnet generator. The results have been obtained through a precisely determined mathematical model and by simulating the characteristics of all essential values for the entire drive. This work is related to the experimental working stand for electric and hybrid car drive research, which has been developed at the Faculty of Electrical Engineering (FEE at CTU in Prague. 

Loss minimization control and efficiency determination of electric drives in traction applications

Energy Technology Data Exchange (ETDEWEB)

Windisch, Thomas; Hofmann, Wilfried [Technische Univ. Dresden (Germany). Lehrstuhl fuer Elektrische Maschinen und Antriebe

2012-11-01

High-power electric drives in automotive traction applications consume a large part of the disposable electric energy. For this reason the energy efficiency of the drives is of great importance for range and fuel consumption of the hybrid electric vehicle. The paper describes two possible drives with different electric motors from a control point of view. The electric power losses in the drive system are determined depending on the operating point of the machine. With these loss characteristics the control of the drives is optimized to produce minimal losses. Finally the energy efficiency for a realistic urban bus drive cycle is calculated to compare the two types. (orig.)

Computer-Aided Engineering for Electric-Drive Vehicle Batteries (CAEBAT) |

Science.gov (United States)

Transportation Research | NREL Computer-Aided Engineering for Electric-Drive Vehicle Batteries (CAEBAT) Computer-Aided Engineering for Electric-Drive Vehicle Batteries (CAEBAT) Graphic of a 24-cell (bottom). Images: Courtesy of EC Power NREL's work on the U.S. Department of Energy Computer-Aided

Analysis of the Fuel Efficiency of a Hybrid Electric Drive with an Electric Power Splitter

OpenAIRE

D. Čundev

2008-01-01

This paper presents the results of an analysis of the fuel efficiency of a hybrid electric car drive, with an electric power splitter based on a double rotor synchronous permanent magnet generator. The results have been obtained through a precisely determined mathematical model and by simulating the characteristics of all essential values for the entire drive. This work is related to the experimental working stand for electric and hybrid car drive research, which has been developed at the Fac...

Large-Scale Battery System Development and User-Specific Driving Behavior Analysis for Emerging Electric-Drive Vehicles

Directory of Open Access Journals (Sweden)

Yihe Sun

2011-04-01

Full Text Available Emerging green-energy transportation, such as hybrid electric vehicles (HEVs and plug-in HEVs (PHEVs, has a great potential for reduction of fuel consumption and greenhouse emissions. The lithium-ion battery system used in these vehicles, however, is bulky, expensive and unreliable, and has been the primary roadblock for transportation electrification. Meanwhile, few studies have considered user-specific driving behavior and its significant impact on (PHEV fuel efficiency, battery system lifetime, and the environment. This paper presents a detailed investigation of battery system modeling and real-world user-specific driving behavior analysis for emerging electric-drive vehicles. The proposed model is fast to compute and accurate for analyzing battery system run-time and long-term cycle life with a focus on temperature dependent battery system capacity fading and variation. The proposed solution is validated against physical measurement using real-world user driving studies, and has been adopted to facilitate battery system design and optimization. Using the collected real-world hybrid vehicle and run-time driving data, we have also conducted detailed analytical studies of users’ specific driving patterns and their impacts on hybrid vehicle electric energy and fuel efficiency. This work provides a solid foundation for future energy control with emerging electric-drive applications.

Integration of electric drive vehicles in the Danish electricity network with high wind power penetration

DEFF Research Database (Denmark)

Chandrashekhara, Divya K; Østergaard, Jacob; Larsen, Esben

2010-01-01

/conventional) which are likely to fuel these cars. The study was carried out considering the Danish electricity network state around 2025, when the EDV penetration levels would be significant enough to have an impact on the power system. Some of the interesting findings of this study are - EDV have the potential......This paper presents the results of a study carried out to examine the feasibility of integrating electric drive vehicles (EDV) in the Danish electricity network which is characterised by high wind power penetration. One of the main aims of this study was to examine the effect of electric drive...... vehicles on the Danish electricity network, wind power penetration and electricity market. In particular the study examined the effect of electric drive vehicles on the generation capacity constraints, load curve, cross border transmission capacity and the type of generating sources (renewable...

Novel Straight and Circular Road Driving Control of Electric Power Assisted Wheelchair Based on Fuzzy Algorithm

Science.gov (United States)

Seki, Hirokazu; Tadakuma, Susumu

This paper describes a novel straight and circular road driving control scheme for electric power assisted wheelchairs. “Electric power assisted wheelchair” which assists the driving force by electric motors is expected to be widely used as a mobility support system for elderly people and disabled people, however, the performance of the straight and circular road driving must be further improved because the two wheels drive independently. This paper proposes a novel driving control scheme based on fuzzy algorithm to realize the stable and reliable driving on straight and circular roads. The suitable assisted torque of the right and left wheels is determined by fuzzy algorithm based on the posture angular velocity of the wheelchair and the human input torque proportion of the right and left wheels. Some experiments on the practical roads show the effectiveness of the proposed control system.

An electric-drive vehicle strategy for Sweden

Energy Technology Data Exchange (ETDEWEB)

Sperling, D.; Lipman, T. [California Univ., Davis, CA (United States). Inst. of Transportation Studies; Lundberg, M. [Swedish Transport and Communications Research Board, Stockholm (Sweden)

2000-07-01

The strategy that Sweden has taken regarding the use of electric-powered vehicles (EVs) to mitigate the environmental impacts caused by the transportation sector was discussed. Sweden's unique attributes include inexpensive and clean electricity, a strong environmental ethic and a strong automotive sector. All versions of electric-drive technology are considered to be environmentally superior to internal combustion engine vehicles. While the cost of batteries is dropping, they will remain highly priced. However, manufacturers are making larger investments into hybrid EVs and fuel cell EVs. Electric drive buses are also gaining in popularity as a means by which to reduce exhaust gases in urban areas. Sweden's industrial policy is aimed at manufacturing electrically driven heavy duty vehicles such as buses and trucks. The environmental policy is aimed at deploying small EVs for on and off-road transportation use, as well as heavy duty EVs targeted by the industrial policy. refs.

Electric powertrain modeling of a fuel cell hybrid electric vehicle and development of a power distribution algorithm based on driving mode recognition

Energy Technology Data Exchange (ETDEWEB)

Ryu, Junghwan; Park, Yeongseop; Sunwoo, Myoungho [Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea)

2010-09-01

This paper proposes a novel fuzzy controller based on an adaptive membership function for optimum power management of a fuel cell hybrid electric vehicle (FCHEV). In the first phase, an electric powertrain model of the FCHEV is derived and a fuzzy controller is proposed. Then, the fuzzy controller is optimized using a genetic algorithm. The optimization process is accomplished through simulation for a given driving cycle. Since, however, the optimized result may vary according to the applied driving cycle for optimization, it is impossible for one optimized result to cover various driving cycles. In the second phase, an adaptive membership function based on a stochastic approach is proposed to guarantee optimum performance from the presented fuzzy controller, even though the driving cycle changes. This controller is referred to as the 'Stochastic fuzzy controller' (SFC) in this study. The SFC employs a stochastic approach where membership functions can be transformed statistically using a probability evaluated from driving pattern recognition. Then, driving cycle analysis is performed through off-line simulation and hardware in a loop simulation (HILS) test for four driving cycles. Finally, the SFC shows the best performance in terms of minimum fuel consumption and state-of-charge (SoC) maintenance. (author)

Highway vehicle electric drive in the United States : 2009 status and issues.

Energy Technology Data Exchange (ETDEWEB)

Santini, D. J.; Energy Systems

2011-02-16

The status of electric drive technology in the United States as of early 2010 is documented. Rapidly evolving electric drive technologies discussed include hybrid electric vehicles, multiple types of plug-in hybrid electric vehicles, and battery electric vehicles. Recent trends for hybrids are quantified. Various plug-in vehicles entering the market in the near term are examined. The technical and economic requirements for electric drive to more broadly succeed in a wider range of highway vehicle applications are described, and implications for the most promising new markets are provided. Federal and selected state government policy measures promoting and preparing for electric drive are discussed. Taking these into account, judgment on areas where increased Clean Cities funds might be most productively focused over the next five years are provided. In closing, the request by Clean Cities for opinion on the broad range of research needs providing near-term support to electric drive is fulfilled.

Multiphysics simulation by design for electrical machines, power electronics and drives

CERN Document Server

Rosu, Marius; Lin, Dingsheng; Ionel, Dan M; Popescu, Mircea; Blaabjerg, Frede; Rallabandi, Vandana; Staton, David

2018-01-01

This book combines the knowledge of experts from both academia and the software industry to present theories of multiphysics simulation by design for electrical machines, power electronics, and drives. The comprehensive design approach described within supports new applications required by technologies sustaining high drive efficiency. The highlighted framework considers the electric machine at the heart of the entire electric drive. The book also emphasizes the simulation by design concept--a concept that frames the entire highlighted design methodology, which is described and illustrated by various advanced simulation technologies. Multiphysics Simulation by Design for Electrical Machines, Power Electronics and Drives begins with the basics of electrical machine design and manufacturing tolerances. It also discusses fundamental aspects of the state of the art design process and includes examples from industrial practice. It explains FEM-based analysis techniques for electrical machine design--providing deta...

Electrical motor/generator drive apparatus and method

Science.gov (United States)

Su, Gui Jia

2013-02-12

The present disclosure includes electrical motor/generator drive systems and methods that significantly reduce inverter direct-current (DC) bus ripple currents and thus the volume and cost of a capacitor. The drive methodology is based on a segmented drive system that does not add switches or passive components but involves reconfiguring inverter switches and motor stator winding connections in a way that allows the formation of multiple, independent drive units and the use of simple alternated switching and optimized Pulse Width Modulation (PWM) schemes to eliminate or significantly reduce the capacitor ripple current.

E-drive with electrically controlled differential; E-Antrieb mit elektrisch geregeltem Differenzial

Energy Technology Data Exchange (ETDEWEB)

Smetana, Tomas; Biermann, Thorsten [Schaeffler Technologies GmbH und Co. KG, Herzogenaurach (Germany); Rohe, Marco [AFT Atlas Fahrzeugtechnik GmbH, Werdohl (Germany); Heinrich, Wolfgang [IDAM, Suhl (Germany)

2011-10-15

Schaeffler is presenting an all-wheel drive electric vehicle named 'Active eDrive'. The name is intended principally to convey innovation and the USP of the drive system: an electric differential with a torque vectoring function. The system combines the final drive with intelligent transverse torque distribution which, when used on axles, enables the distribution of torque over the longitudinal axis of the vehicle. The final drive can be integrated in both electric and hybrid vehicles with or without a range extender capability. The authors first explain the mechanical requirements and then describe the electrical systems that are intended to fulfill these. (orig.)

Vehicle Dynamics Control of In-wheel Electric Motor Drive Vehicles Based on Averaging of Tire Force Usage

Science.gov (United States)

Masaki, Nobuo; Iwano, Haruo; Kamada, Takayoshi; Nagai, Masao

For in-wheel electric motor drive vehicles, a new vehicle dynamics control which is based on the tire force usage rate is proposed. The new controller adopts non-linear optimal control could manage the interference between direct yaw-moment control and the tire force usage rate. The new control is considered total longitudinal and transverse tire force. Therefore the controller can prevent tire force saturation near tire force limit during cornering. Simulations and test runs by the custom made four wheel drive in-wheel motor electric vehicle show that higher driving stability performance compared to the performance of the same vehicle without control.

Electrical drives of the safety system in nuclear power plants

International Nuclear Information System (INIS)

1990-09-01

Actuating drives, control magnets for ventilators, machine drives and control member drives are part of this rule. The rule deals with the security and technical requirements for design, construction, calculation, fabrication, assembling, testing and operation. Furthermore, it places significant demands, with regard to planning and arrangement of electrical drives, on the accompanying technical systems. Furthermore, demands are placed on the aggregate protection for electrical drives of the security systems. The signals given to these systems do not, however, have precedence over the protection signals of the reactor. The rule is identical with KTA-3504, version 9/1988. (orig./HP) [de

Integrated Inverter For Driving Multiple Electric Machines

Science.gov (United States)

Su, Gui-Jia [Knoxville, TN; Hsu, John S [Oak Ridge, TN

2006-04-04

An electric machine drive (50) has a plurality of inverters (50a, 50b) for controlling respective electric machines (57, 62), which may include a three-phase main traction machine (57) and two-phase accessory machines (62) in a hybrid or electric vehicle. The drive (50) has a common control section (53, 54) for controlling the plurality of inverters (50a, 50b) with only one microelectronic processor (54) for controlling the plurality of inverters (50a, 50b), only one gate driver circuit (53) for controlling conduction of semiconductor switches (S1-S10) in the plurality of inverters (50a, 50b), and also includes a common dc bus (70), a common dc bus filtering capacitor (C1) and a common dc bus voltage sensor (67). The electric machines (57, 62) may be synchronous machines, induction machines, or PM machines and may be operated in a motoring mode or a generating mode.

Simulation models of a drive with an asynchronous electric engine for students of electrical engineering faculties

Directory of Open Access Journals (Sweden)

Romanenko N. G.

2017-10-01

Full Text Available the application of virtual laboratories will allow to show different transition processes, as well as to carry out experiments that are very expensive in real electrical machines’ labs, for example, to calculate the energy costs in electric drives. Models of non-regulation asynchronous drive and frequency-regulated asynchronous electric drive are examined in this article. The author has calculated and compared the energy losses of these systems with various types of loads and this lets us to evaluate work processes of many technical devices.

Rig`s electricity to power top drive drilling system

Energy Technology Data Exchange (ETDEWEB)

Liderth, D.

1996-05-01

Permanent magnet brushless electric motors to supply torque to more space-efficient top drive drilling assemblies was the solution designed by Kaman Electromagnetic Corporation, working hand-in-hand with Calgary-based Tesco Drilling Technology, to remedy problems created by the bulkiness of standard hydraulic top drive systems. The biggest advantage of using electric over hydraulic top drive systems is the ability to tap into the rig`s existing power source, which lowers both cost and effort. A better power to weight ratio and reduced maintenance requirements are other desirable advantages.

On the competitiveness of electric driving in France: Impact of driving patterns

International Nuclear Information System (INIS)

Le Duigou, A.; Amalric, Y.; Guan, Y.

2014-01-01

The environmental issues in the transport sector are numerous and CO 2 capture is not even plausible for vehicles at the moment. This report describes a number of different emergent power train technologies (ICE, BEV, PHEV, FCEV) before providing an inter-comparison of these technologies within a technical and economic context. The economical benefits are discussed in terms of the 'Difference of Total Cost of Ownership' (DTCO) and take: electric driving distances, energy (fuel, electricity, hydrogen) prices, batteries and fuel cells costs. To simulate electric driving distances, the model uses several functional parameters such as the battery range and the 'range anxiety' based on the assumption of one recharge per day. The potential electric driving distances are evaluated according to the segmentation statistics of daily trips. The results show the yearly mileages, as well as the range and cost of batteries and fuel cells, together with their relative impact on the DTCO and on the competitiveness of electric vehicles. The price of electric vehicles remains high with strong dependency on the battery's capacity, but the benefits in terms of fuel cost savings can be considerable. The price of electricity is currently noticeably lower than petroleum-based fuels, which balances the high costs of the batteries. 50% or more of LDV yearly mileages can be electric-driven, even for limited battery ranges (ca.under 50 km). There are stakes for the battery costs (competitiveness under euros-215/kWh) and lifetimes, while the low battery ranges (100 km in our case) provide the best margins. As regards FCEVs, the hydrogen target price at the pump should be achievable (less than euros-6.5/kg) with reasonable gasoline prices (Euros-1.7/liter at the pump) and fuel cell costs (euros-20/kW). CO 2 taxes and ICE efficiency gains will lead to opposite impacts of the H 2 target prices at the pump. (authors)

HIL Simulation of Power Electronics and Electric Drives for Automotive Applications

OpenAIRE

Frank Puschmann; Axel Kiffe; Thomas Schulte

2012-01-01

Hardware-in-the-loop simulation is today a standard method for testing electronic equipment in the automotive industry. Since electric drives and power electronic devices are more and more important in automotive applications, these kinds of systems have to be integrated into the hardware-in-the-loop simulation. Power converters and electric drives are used in many different applications in vehicles today (hybrid electric or electric powertrain, electric steering systems, DC-DC converters, et...

Microelectronics in power electronics and electrical drives

Energy Technology Data Exchange (ETDEWEB)

1982-01-01

From October, 1214, 1982 at Darmstadt (FRG) a meeting took place on ''Microelectronics in power electronics and Electrical Drives''. This volume contains the papers of the 65 lectures, held at the symposium. For each of the 10 papers dealing with problems on electric-powered vehicles a separate subject analysis has been carried out.

Alternating-Current Motor Drive for Electric Vehicles

Science.gov (United States)

Krauthamer, S.; Rippel, W. E.

1982-01-01

New electric drive controls speed of a polyphase as motor by varying frequency of inverter output. Closed-loop current-sensing circuit automatically adjusts frequency of voltage-controlled oscillator that controls inverter frequency, to limit starting and accelerating surges. Efficient inverter and ac motor would give electric vehicles extra miles per battery charge.

HIL Simulation of Power Electronics and Electric Drives for Automotive Applications

Directory of Open Access Journals (Sweden)

Frank Puschmann

2012-12-01

Full Text Available Hardware-in-the-loop simulation is today a standard method for testing electronic equipment in the automotive industry. Since electric drives and power electronic devices are more and more important in automotive applications, these kinds of systems have to be integrated into the hardware-in-the-loop simulation. Power converters and electric drives are used in many different applications in vehicles today (hybrid electric or electric powertrain, electric steering systems, DC-DC converters, etc.. The wide range of applications, topologies, and power levels results in various different approaches and solutions for hardware-in-the-loop testing. This paper gives an overview of hardware-in-the-loop simulation of power electronics and electric drives in the automotive industry. The currently available technologies are described and future challenges are outlined.

Extended driving impairs nocturnal driving performances.

Directory of Open Access Journals (Sweden)

Patricia Sagaspe

Full Text Available Though fatigue and sleepiness at the wheel are well-known risk factors for traffic accidents, many drivers combine extended driving and sleep deprivation. Fatigue-related accidents occur mainly at night but there is no experimental data available to determine if the duration of prior driving affects driving performance at night. Participants drove in 3 nocturnal driving sessions (3-5 am, 1-5 am and 9 pm-5 am on open highway. Fourteen young healthy men (mean age [+/-SD] = 23.4 [+/-1.7] years participated Inappropriate line crossings (ILC in the last hour of driving of each session, sleep variables, self-perceived fatigue and sleepiness were measured. Compared to the short (3-5 am driving session, the incidence rate ratio of inappropriate line crossings increased by 2.6 (95% CI, 1.1 to 6.0; P<.05 for the intermediate (1-5 am driving session and by 4.0 (CI, 1.7 to 9.4; P<.001 for the long (9 pm-5 am driving session. Compared to the reference session (9-10 pm, the incidence rate ratio of inappropriate line crossings were 6.0 (95% CI, 2.3 to 15.5; P<.001, 15.4 (CI, 4.6 to 51.5; P<.001 and 24.3 (CI, 7.4 to 79.5; P<.001, respectively, for the three different durations of driving. Self-rated fatigue and sleepiness scores were both positively correlated to driving impairment in the intermediate and long duration sessions (P<.05 and increased significantly during the nocturnal driving sessions compared to the reference session (P<.01. At night, extended driving impairs driving performances and therefore should be limited.

FY2015 Electric Drive Technologies Annual Progress Report

Energy Technology Data Exchange (ETDEWEB)

None, None

2016-02-29

The Electric Drive Technologies research and development (R&D) subprogram within the DOE Vehicle Technologies Office (VTO) provides support and guidance for many cutting-edge automotive technologies under development. Research is focused on developing power electronics (PE), electric motor, and traction drive system (TDS) technologies that will reduce system cost and improve their efficiency in transforming battery energy to useful work. The R&D is also aimed at better understanding and improving how various components of tomorrow’s automobiles will function as a unified system to improve fuel efficiency.

FY2014 Electric Drive Technologies Annual Progress Report

Energy Technology Data Exchange (ETDEWEB)

None

2014-12-01

The Electric Drive Technologies research and development (R&D) subprogram within the DOE Vehicle Technologies Office (VTO) provides support and guidance for many cutting-edge automotive technologies under development. Research is focused on developing power electronics (PE), electric motor, and traction drive system (TDS) technologies that will reduce system cost and improve their efficiency in transforming battery energy to useful work. The R&D is also aimed at better understanding and improving how various components of tomorrow’s automobiles will function as a unified system to improve fuel efficiency.

FY2016 Electric Drive Technologies Annual Progress Report

Energy Technology Data Exchange (ETDEWEB)

None, None

2017-07-03

The Electric Drive Technologies research and development (R&D) subprogram within the DOE Vehicle Technologies Office (VTO) provides support and guidance for many cutting-edge automotive technologies under development. Research is focused on developing power electronics (PE), electric motor, and traction drive system (TDS) technologies that will reduce system cost and improve their efficiency in transforming battery energy to useful work. The R&D is also aimed at better understanding and improving how various components of tomorrow’s automobiles will function as a unified system to improve fuel efficiency.

Analytical approaches to optimizing system "Semiconductor converter-electric drive complex"

Science.gov (United States)

Kormilicin, N. V.; Zhuravlev, A. M.; Khayatov, E. S.

2018-03-01

In the electric drives of the machine-building industry, the problem of optimizing the drive in terms of mass-size indicators is acute. The article offers analytical methods that ensure the minimization of the mass of a multiphase semiconductor converter. In multiphase electric drives, the form of the phase current at which the best possible use of the "semiconductor converter-electric drive complex" for active materials is different from the sinusoidal form. It is shown that under certain restrictions on the phase current form, it is possible to obtain an analytical solution. In particular, if one assumes the shape of the phase current to be rectangular, the optimal shape of the control actions will depend on the width of the interpolar gap. In the general case, the proposed algorithm can be used to solve the problem under consideration by numerical methods.

Smart sensorless prediction diagnosis of electric drives

Science.gov (United States)

Kruglova, TN; Glebov, NA; Shoshiashvili, ME

2017-10-01

In this paper, the discuss diagnostic method and prediction of the technical condition of an electrical motor using artificial intelligent method, based on the combination of fuzzy logic and neural networks, are discussed. The fuzzy sub-model determines the degree of development of each fault. The neural network determines the state of the object as a whole and the number of serviceable work periods for motors actuator. The combination of advanced techniques reduces the learning time and increases the forecasting accuracy. The experimental implementation of the method for electric drive diagnosis and associated equipment is carried out at different speeds. As a result, it was found that this method allows troubleshooting the drive at any given speed.

Two wheel speed robust sliding mode control for electric vehicle drive

Directory of Open Access Journals (Sweden)

Abdelfatah Nasri

2008-01-01

Full Text Available Nowadays the uses of electrical power resources are integrated in the modern vehicle motion traction chain so new technologies allow the development of electric vehicles (EV by means of static converters-related electric motors. All mechanical transmission devices are eliminated and vehicle wheel motion can be controlled by means of power electronics. The proposed propulsing system consists of two induction motors (IM that ensure the drive of the two back driving wheels. The proposed control structure-called independent machines- for speed control permit the achievement of an electronic differential. The electronic differential system ensures the robust control of the vehicle behavior on the road. It also allows controlling independently, every driving wheel to turn at different speeds in any curve. This paper presents the study and the sliding mode control strategy of the electric vehicle driving wheels.

Sixth international conference on electrical machines and drives

International Nuclear Information System (INIS)

1993-01-01

This volume contains 111 papers presented at the Sixth International Conference on Electrical Machines and Drives. The topics covered include: miniature and micro motors; induction motors; DC machines; reluctance motors; condition monitoring; synchronous machines and drives; induction machines; induction generators; simulation; design; and operating experience; linear machines; noise and vibration; special machines. Separate abstracts have been prepared for a paper on linear step motors for control rod drives and for a paper on a motor drive for gas filtration in gas-cooled reactors. (UK)

Powertrain Matching and Optimization of Dual-Motor Hybrid Driving System for Electric Vehicle Based on Quantum Genetic Intelligent Algorithm

Directory of Open Access Journals (Sweden)

Yong Wang

2014-01-01

Full Text Available In order to increase the driving range and improve the overall performance of all-electric vehicles, a new dual-motor hybrid driving system with two power sources was proposed. This system achieved torque-speed coupling between the two power sources and greatly improved the high performance working range of the motors; at the same time, continuously variable transmission (CVT was achieved to efficiently increase the driving range. The power system parameters were determined using the “global optimization method”; thus, the vehicle’s dynamics and economy were used as the optimization indexes. Based on preliminary matches, quantum genetic algorithm was introduced to optimize the matching in the dual-motor hybrid power system. Backward simulation was performed on the combined simulation platform of Matlab/Simulink and AVL-Cruise to optimize, simulate, and verify the system parameters of the transmission system. Results showed that quantum genetic algorithms exhibited good global optimization capability and convergence in dealing with multiobjective and multiparameter optimization. The dual-motor hybrid-driving system for electric cars satisfied the dynamic performance and economy requirements of design, efficiently increasing the driving range of the car, having high performance, and reducing energy consumption of 15.6% compared with the conventional electric vehicle with single-speed reducers.

Acceleration Slip Regulation Strategy for Distributed Drive Electric Vehicles with Independent Front Axle Drive Motors

Directory of Open Access Journals (Sweden)

Lingfei Wu

2015-05-01

Full Text Available This paper presents an acceleration slip regulation strategy for distributed drive electric vehicles with two motors on the front axle. The tasks of the strategy include controlling the slip ratio to make full use of the road grip and controlling the yaw rate to eliminate the lateral movement due to the difference between motor torques. The rate of the slip ratio change can be controlled by controlling the motor torque, so that the slip ratio can be controlled by applying a proportional-integral control strategy to control the rate of the slip ratio change. The yaw rate can be controlled to almost zero by applying torque compensation based on yaw rate feedback. A coordination control strategy for the slip ratio control and yaw rate control is proposed based on analysis of the priorities and features of the two control processes. Simulations were carried out using MATLAB/Simulink, and experiments were performed on a hardware-in-loop test bench with actual motors. The results of the simulations and experiments showed that the proposed strategy could improve the longitudinal driving performance and straight line driving stability of the vehicle.

Multi-Phase Modular Drive System: A Case Study in Electrical Aircraft Applications

Directory of Open Access Journals (Sweden)

Charles Onambele

2017-12-01

Full Text Available In this article, an advanced multiphase modular power drive prototype is developed for More Electric Aircraft (MEA. The proposed drive is designed to supply a multi-phase permanent magnet (PM motor rating 120 kW with 24 slots and 11 pole pairs. The power converter of the drive system is based on Silicon Carbide Metal Oxide Semiconductor Field-Effect Transistor (SiC MOSFET technology to operate at high voltage, high frequency and low reverse recovery current. Firstly, an experimental characterization test is performed for the selected SiC power module in harsh conditions to evaluate the switching energy losses. Secondly, a finite element thermal analysis based on Ansys-Icepak is accomplished to validate the selected cooling system for the power converter. Thirdly, a co-simulation model is developed using Matlab-Simulink and LTspice® to evaluate the SiC power module impact on the performance of a multiphase drive system at different operating conditions. The results obtained show that the dynamic performance and efficiency of the power drive are significantly improved, which makes the proposed system an excellent candidate for future aircraft applications.

Electrical machines and drives

CERN Document Server

Hindmarsh, John

2002-01-01

Recent years have brought substantial developments in electrical drive technology, with the appearance of highly rated, very-high-speed power-electronic switches, combined with microcomputer control systems.This popular textbook has been thoroughly revised and updated in the light of these changes. It retains its successful formula of teaching through worked examples, which are put in context with concise explanations of theory, revision of equations and discussion of the engineering implications. Numerous problems are also provided, with answers supplied.The third edition in

Automated complex for research of electric drives control

Science.gov (United States)

Avlasko, P. V.; Antonenko, D. A.

2018-05-01

In the article, the automated complex intended for research of various control modes of electric motors including the inductor motor of double-way feed is described. As a basis of the created complex, the National Instruments platform is chosen. The operating controller built in a platform is delivered with an operating system of real-time for creation of systems of measurement and management. The software developed in the environment of LabVIEW consists of several connected modules which are in different elements of a complex. Besides the software for automated management by experimental installation, the program complex is developed for modelling of processes in the electric drive. As a result there is an opportunity to compare simulated and received experimentally transitional characteristics of the electric drive in various operating modes.

Intellectual Drive With Electric Engines On a Stock Car

Directory of Open Access Journals (Sweden)

Bazhynov O.V.

2016-04-01

Full Text Available The concept of installing smart electric drive, battery unit and control system of a stock car is presented. This work is devoted to AEM control law consisting of auto power plant, providing minimum current consumption for a given traction and speed mode. The practicability of AEM static model usage in the process of synthesis of optimal control of auto power plant with traction electric drives and also choice and substantiation of its basic parameters and characteristics is demonstrated.

Combined Optimal Control System for excavator electric drive

Science.gov (United States)

Kurochkin, N. S.; Kochetkov, V. P.; Platonova, E. V.; Glushkin, E. Y.; Dulesov, A. S.

2018-03-01

The article presents a synthesis of the combined optimal control algorithms of the AC drive rotation mechanism of the excavator. Synthesis of algorithms consists in the regulation of external coordinates - based on the theory of optimal systems and correction of the internal coordinates electric drive using the method "technical optimum". The research shows the advantage of optimal combined control systems for the electric rotary drive over classical systems of subordinate regulation. The paper presents a method for selecting the optimality criterion of coefficients to find the intersection of the range of permissible values of the coordinates of the control object. There is possibility of system settings by choosing the optimality criterion coefficients, which allows one to select the required characteristics of the drive: the dynamic moment (M) and the time of the transient process (tpp). Due to the use of combined optimal control systems, it was possible to significantly reduce the maximum value of the dynamic moment (M) and at the same time - reduce the transient time (tpp).

Electric driving accelerated. Action Plan 2011-2015. Annex 2

International Nuclear Information System (INIS)

2011-10-01

The Dutch Action Plan for Electric Driving gives form and substance to the ambition of the Dutch government to accelerate the market introduction of electric cars in the Netherlands. This plan is not only focused on the electric passenger car. To promote the electrification of transport, also electric garbage trucks, buses, scooters and possibly pleasure boats are included in the plan. [nl

Variable speed electrical driving systems; Entrainements electriques a vitesse variable

Energy Technology Data Exchange (ETDEWEB)

Bonal, J. [ESE, Promethee, Groupe Schneider (France)

1997-12-31

This book is the first of a series of 3 volumes which synthesize the most recent knowledge on variable speed electrical driving systems. It is devoted to electronic and electromechanical engineers and technicians and to manufacturers of electrical equipments involving such systems. after a recall of basic electrotechnical and mechanical notions, this book focusses on the functionalities and criteria of definition of driving systems, and shows the interactions between the different parts of these equipments. It develops a methodological approach of the choice for the most suitable technology with respect to the application under consideration. Various industrial sectors are concerned and a particular attention is paid to the driving of receptive turbo-machineries which play a major role in the energy balance sheet of the industrial electrical power force. (J.S.) 28 refs.

Drive Control Scheme of Electric Power Assisted Wheelchair Based on Neural Network Learning of Human Wheelchair Operation Characteristics

Science.gov (United States)

Tanohata, Naoki; Seki, Hirokazu

This paper describes a novel drive control scheme of electric power assisted wheelchairs based on neural network learning of human wheelchair operation characteristics. “Electric power assisted wheelchair” which enhances the drive force of the operator by employing electric motors is expected to be widely used as a mobility support system for elderly and disabled people. However, some handicapped people with paralysis of the muscles of one side of the body cannot maneuver the wheelchair as desired because of the difference in the right and left input force. Therefore, this study proposes a neural network learning system of such human wheelchair operation characteristics and a drive control scheme with variable distribution and assistance ratios. Some driving experiments will be performed to confirm the effectiveness of the proposed control system.

Cooling Performance Characteristics of the Stack Thermal Management System for Fuel Cell Electric Vehicles under Actual Driving Conditions

Directory of Open Access Journals (Sweden)

Ho-Seong Lee

2016-04-01

Full Text Available The cooling performance of the stack radiator of a fuel cell electric vehicle was evaluated under various actual road driving conditions, such as highway and uphill travel. The thermal stability was then optimized, thereby ensuring stable operation of the stack thermal management system. The coolant inlet temperature of the radiator in the highway mode was lower than that associated with the uphill mode because the corresponding frontal air velocity was higher than obtained in the uphill mode. In both the highway and uphill modes, the coolant temperatures of the radiator, operated under actual road driving conditions, were lower than the allowable limit (80 °C; this is the maximum temperature at which stable operation of the stack thermal management system of the fuel cell electric vehicle could be maintained. Furthermore, under actual road driving conditions in uphill mode, the initial temperature difference (ITD between the coolant temperature and air temperature of the system was higher than that associated with the highway mode; this higher ITD occurred even though the thermal load of the system in uphill mode was greater than that corresponding to the highway mode. Since the coolant inlet temperature is expected to exceed the allowable limit (80 °C in uphill mode under higher ambient temperature with air conditioning system operation, the FEM design layout should be modified to improve the heat capacity. In addition, the overall volume of the stack cooling radiator is 52.2% higher than that of the present model and the coolant inlet temperature of the improved radiator is 22.7% lower than that of the present model.

A High-Performance Control Method of Constant V/f-Controlled Induction Motor Drives for Electric Vehicles

Directory of Open Access Journals (Sweden)

Long Chen

2014-01-01

Full Text Available A three-phase induction motor used as a propulsion system for the electric vehicle (EV is a nonlinear, multi-input multi-output, and strong coupling system. For such a complicated model system with unmeasured and unavoidable disturbances, as well as parameter variations, the conventional vector control method cannot meet the demands of high-performance control. Therefore, a novel control strategy named least squares support vector machines (LSSVM inverse control is presented in the paper. Invertibility of the induction motor in the constant V/f control mode is proved to confirm its feasibility. The LSSVM inverse is composed of an LSSVM approximating the nonlinear mapping of the induction motor and two integrators. The inverse model of the constant V/f-controlled induction motor drive is obtained by using LSSVM, and then the optimal parameters of LSSVM are determined automatically by applying a modified particle swarm optimization (MPSO. Cascading the LSSVM inverse with the induction motor drive system, the pseudolinear system can be obtained. Thus, it is easy to design the closed-loop linear regulator. The simulation results verify the effectiveness of the proposed method.

Electric machinery and drives in thermal power stations

International Nuclear Information System (INIS)

1974-01-01

The following subjects were dealt with during the VDE meeting: 1) Requirements made by the electric network on the generators and their excitation equipment, and the influence thereof on their design; 2) requirements made by the power station process on the electric drives and the influence thereof on type and design; 3) requirements made on protective measures from the point of the electric power station machinery. (TK) [de

Analysis of electric machinery and drive systems

CERN Document Server

Krause, Paul C; Sudhoff, Scott D; Pekarek, Steven

2013-01-01

Introducing a new edition of the popular reference on machine analysis Now in a fully revised and expanded edition, this widely used reference on machine analysis boasts many changes designed to address the varied needs of engineers in the electric machinery, electric drives, and electric power industries. The authors draw on their own extensive research efforts, bringing all topics up to date and outlining a variety of new approaches they have developed over the past decade. Focusing on reference frame theory that has been at the core of this work since the first edition, th

Battery prices and capacity sensitivity: Electric drive vehicles

DEFF Research Database (Denmark)

Juul, Nina

2012-01-01

, the prices at which the electric drive vehicles become of interest to the power system are found. Smart charge, including the opportunity to discharge (vehicle-to-grid) is used in all scenarios. Analyses show that the marginal benefits decrease the larger the battery. For very high battery prices, large......The increase in fluctuating power production requires an increase in flexibility in the system as well. Flexibility can be found in generation technologies with fast response times or in storage options. In the transport sector, the proportion of electric drive vehicles is expected to increase over...... the next decade or two. These vehicles can provide some of the flexibility needed in the power system, in terms of both flexible demand and electricity storage. However, what are the batteries worth to the power system? And does the value depend on battery capacity? This article presents an analysis...

Electric machine and current source inverter drive system

Science.gov (United States)

Hsu, John S

2014-06-24

A drive system includes an electric machine and a current source inverter (CSI). This integration of an electric machine and an inverter uses the machine's field excitation coil for not only flux generation in the machine but also for the CSI inductor. This integration of the two technologies, namely the U machine motor and the CSI, opens a new chapter for the component function integration instead of the traditional integration by simply placing separate machine and inverter components in the same housing. Elimination of the CSI inductor adds to the CSI volumetric reduction of the capacitors and the elimination of PMs for the motor further improve the drive system cost, weight, and volume.

The effect of electric field geometry on the performance of electromembrane extraction systems: Footprints of a third driving force along with migration and diffusion

Energy Technology Data Exchange (ETDEWEB)

Moazami, Hamid Reza [School of Physics and Accelerators, NSTRI, P. O. Box, 11365-8486, Tehran (Iran, Islamic Republic of); Hosseiny Davarani, Saied Saeed, E-mail: ss-hosseiny@sbu.ac.ir [Faculty of Chemistry, Shahid Beheshti University, G. C., 1983963113, Evin, Tehran (Iran, Islamic Republic of); Mohammadi, Jamil; Nojavan, Saeed [Faculty of Chemistry, Shahid Beheshti University, G. C., 1983963113, Evin, Tehran (Iran, Islamic Republic of); Abrari, Masoud [Laser and Plasma Research Institute, Shahid Beheshti University, G. C., 1983963113, Evin, Tehran (Iran, Islamic Republic of)

2015-09-03

The distribution of electric field vectors was first calculated for electromembrane extraction (EME) systems in classical and cylindrical electrode geometries. The results showed that supported liquid membrane (SLM) has a general field amplifying effect due to its lower dielectric constant in comparison with aqueous donor/acceptor solutions. The calculated norms of the electric field vector showed that a DC voltage of 50 V can create huge electric field strengths up to 64 kV m{sup −1} and 111 kV m{sup −1} in classical and cylindrical geometries respectively. In both cases, the electric field strength reached its peak value on the inner wall of the SLM. In the case of classical geometry, the field strength was a function of the polar position of the SLM whereas the field strength in cylindrical geometry was angularly uniform. In order to investigate the effect of the electrode geometry on the performance of real EME systems, the analysis was carried out in three different geometries including classical, helical and cylindrical arrangements using naproxen and sodium diclofenac as the model analytes. Despite higher field strength and extended cross sectional area, the helical and cylindrical geometries gave lower recoveries with respect to the classical EME. The observed decline of the signal was proved to be against the relations governing migration and diffusion processes, which means that a third driving force is involved in EME. The third driving force is the interaction between the radially inhomogeneous electric field and the analyte in its neutral form. - Highlights: • Electric field vectors have been calculated in EME systems. • A new driving force has been proposed in EME systems. • EME can be theoretically applied to nonionic polarizable analytes.

The effect of electric field geometry on the performance of electromembrane extraction systems: Footprints of a third driving force along with migration and diffusion

International Nuclear Information System (INIS)

Moazami, Hamid Reza; Hosseiny Davarani, Saied Saeed; Mohammadi, Jamil; Nojavan, Saeed; Abrari, Masoud

2015-01-01

The distribution of electric field vectors was first calculated for electromembrane extraction (EME) systems in classical and cylindrical electrode geometries. The results showed that supported liquid membrane (SLM) has a general field amplifying effect due to its lower dielectric constant in comparison with aqueous donor/acceptor solutions. The calculated norms of the electric field vector showed that a DC voltage of 50 V can create huge electric field strengths up to 64 kV m −1 and 111 kV m −1 in classical and cylindrical geometries respectively. In both cases, the electric field strength reached its peak value on the inner wall of the SLM. In the case of classical geometry, the field strength was a function of the polar position of the SLM whereas the field strength in cylindrical geometry was angularly uniform. In order to investigate the effect of the electrode geometry on the performance of real EME systems, the analysis was carried out in three different geometries including classical, helical and cylindrical arrangements using naproxen and sodium diclofenac as the model analytes. Despite higher field strength and extended cross sectional area, the helical and cylindrical geometries gave lower recoveries with respect to the classical EME. The observed decline of the signal was proved to be against the relations governing migration and diffusion processes, which means that a third driving force is involved in EME. The third driving force is the interaction between the radially inhomogeneous electric field and the analyte in its neutral form. - Highlights: • Electric field vectors have been calculated in EME systems. • A new driving force has been proposed in EME systems. • EME can be theoretically applied to nonionic polarizable analytes.

Fast-Response electric drives of Mechanical Engineering objects

Science.gov (United States)

Doykina, L. A.; Bukhanov, S. S.; Gryzlov, A. A.

2018-03-01

The article gives a solution to the problem of increasing the speed in the electrical drives of machine-building enterprises due to the application of a structure with ISC control. In this case, it is possible to get rid of the speed sensors. It is noted that in this case no circulating pulsations are applied to the input of the control system, caused by a non-identical interface between the sensor and the shaft of the operating mechanism. For detailed modeling, a mathematical model of an electric drive with distributed parameters was proposed. The calculation of such system was carried out by the finite element method. Taking into account the distributed characteristic of the system parameters allowed one to take into account the discrete nature of the electric machine’s work. The simulation results showed that the response time in the control circuit is estimated at a time constant of 0.0015, which is about twice as fast as in traditional vector control schemes.

Fuel-Cell-Powered Electric Motor Drive Analyzed for a Large Airplane

Science.gov (United States)

Brown, Gerald V.; Choi, Benjamin B.

2005-01-01

Because of its high efficiency, fuel cell technology may be used to launch a new generation of more-electric aeropropulsion and power systems for future aircraft. Electric-motor-driven airplanes using fuel-cell powerplants would be beneficial to the environment because of fuel savings, low noise, and zero carbon-dioxide emissions. In spite of the fuel cell s efficiency benefit, to produce the same shaft drive power, a fuel cell- powered electric-drive system must be definitely heavier than a turbine-drive system. However, the fuel-cell system s overall efficiency from fuel-to-shaft power is higher than for a turbine-drive system. This means that the fuel consumption rate could be lower than for a conventional system. For heavier, fuel-laden planes for longer flights, we might achieve substantial fuel savings. In the airplane industry, in fact, an efficiency gain of even a few percentage points can make a major economic difference in operating costs.

A Dynamic Control Strategy for Hybrid Electric Vehicles Based on Parameter Optimization for Multiple Driving Cycles and Driving Pattern Recognition

Directory of Open Access Journals (Sweden)

Zhenzhen Lei

2017-01-01

Full Text Available The driving pattern has an important influence on the parameter optimization of the energy management strategy (EMS for hybrid electric vehicles (HEVs. A new algorithm using simulated annealing particle swarm optimization (SA-PSO is proposed for parameter optimization of both the power system and control strategy of HEVs based on multiple driving cycles in order to realize the minimum fuel consumption without impairing the dynamic performance. Furthermore, taking the unknown of the actual driving cycle into consideration, an optimization method of the dynamic EMS based on driving pattern recognition is proposed in this paper. The simulation verifications for the optimized EMS based on multiple driving cycles and driving pattern recognition are carried out using Matlab/Simulink platform. The results show that compared with the original EMS, the former strategy reduces the fuel consumption by 4.36% and the latter one reduces the fuel consumption by 11.68%. A road test on the prototype vehicle is conducted and the effectiveness of the proposed EMS is validated by the test data.

Monitoring and analyzing features of electrical power quality system performance

OpenAIRE

Genci Sharko; Nike Shanku

2010-01-01

Power quality is a set of boundaries that allows electrical systems to function in their intended manner without significant loss of performance or life. The term is used to describe electric power that drives an electrical load and the load's ability to function properly with that electric power. Without the proper quality of the power, an electrical device may malfunction, fail prematurely or not operate at all. There are many reasons why the electric power can be of poor quality and many m...

Using fleets of electric-drive vehicles for grid support

International Nuclear Information System (INIS)

Tomic, Jasna; Kempton, Willett

2007-01-01

Electric-drive vehicles can provide power to the electric grid when they are parked (vehicle-to-grid power). We evaluated the economic potential of two utility-owned fleets of battery-electric vehicles to provide power for a specific electricity market, regulation, in four US regional regulation services markets. The two battery-electric fleet cases are: (a) 100 Th.nk City vehicle and (b) 252 Toyota RAV4. Important variables are: (a) the market value of regulation services, (b) the power capacity (kW) of the electrical connections and wiring, and (c) the energy capacity (kWh) of the vehicle's battery. With a few exceptions when the annual market value of regulation was low, we find that vehicle-to-grid power for regulation services is profitable across all four markets analyzed. Assuming now more than current Level 2 charging infrastructure (6.6 kW) the annual net profit for the Th.nk City fleet is from US$ 7000 to 70,000 providing regulation down only. For the RAV4 fleet the annual net profit ranges from US$ 24,000 to 260,000 providing regulation down and up. Vehicle-to-grid power could provide a significant revenue stream that would improve the economics of grid-connected electric-drive vehicles and further encourage their adoption. It would also improve the stability of the electrical grid. (author)

The Drive-Wise Project: Driving Simulator Training increases real driving performance in healthy older drivers

Directory of Open Access Journals (Sweden)

Gianclaudio eCasutt

2014-05-01

Full Text Available Background: Age-related cognitive decline is often associated with unsafe driving behavior. We hypothesized that 10 active training sessions in a driving simulator increase cognitive and on-road driving performance. In addition, driving simulator training should outperform cognitive training.Methods: Ninety-one healthy active drivers (62 – 87 years were randomly assigned to either (1 a driving simulator training group, (2 an attention training group (vigilance and selective attention, or (3 a control group. The main outcome variables were on-road driving and cognitive performance. Seventy-seven participants (85% completed the training and were included in the analyses. Training gains were analyzed using a multiple regression analysis with planned comparisons.Results: The driving simulator training group showed an improvement in on-road driving performance compared to the attention training group. In addition, both training groups increased cognitive performance compared to the control group. Conclusion: Driving simulator training offers the potential to enhance driving skills in older drivers. Compared to the attention training, the simulator training seems to be a more powerful program for increasing older drivers’ safety on the road.

Drive Electric Vermont Case Study

Energy Technology Data Exchange (ETDEWEB)

Wagner, Fred [Energetics Incorporated, Columbia, MD (United States); Roberts, Dave [Vermont Energy Investment Corporation (VEIC), Burlington, VT (United States); Francfort, Jim [Idaho National Lab. (INL), Idaho Falls, ID (United States); White, Sera [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-03-01

Currently in the United States, the heavy majority of plug-in electric vehicle (PEV) sales have been in highly conducive, selected, metropolitan areas; opposed to more broad distribution across the country. The U.S. Department of Energy’s EV Everywhere Grand Challenge is looking carefully at the barriers and opportunities that exist to enable small and midsize communities to partake in the PEV market and benefit from the economic and environmental advantages of PEVs. In order to gain insight into these challenges and barriers, DOE selected a success story (i.e., Drive Electric Vermont) as the subject of this case study, as the state of Vermont is tied with Detroit, Michigan in having the highest percentage of 2014 (most recent complete data) PEV registrations for cold weather U.S. cities and has seen more than a sixfold increase in charging stations over the last three years. The overall objective of this case study was to use the lessons learned from Drive Electric Vermont to determine what activities are most effective at encouraging acquisitions of PEVs and deployment of charging infrastructure in small to midsize communities, prioritizing and sequencing their implementation, identifying robust means for extrapolation, and applying this understanding to other small to midsize communities across the nation. The Drive Electric Vermont Program was formed in 2012 with a goal of increasing the use of electrified transportation in Vermont through policy development, education and outreach, and infrastructure development. The Drive Electric Vermont Program can be broadly broken into four components: (1) strategic planning/leadership, (2) stakeholder/partnership development, (3) education and outreach, and (4) incentives. The early phases of the program focused heavily on strategic planning, and stakeholder and partnership development, followed by a transition to education and outreach activities, charging infrastructure development, and grant and incentive programs

Preliminary Design of Reluctance Motors for Light Electric Vehicles Driving

Directory of Open Access Journals (Sweden)

TRIFA, V.

2009-02-01

Full Text Available The paper presents the aspects regarding FEM analysis of a reluctant motor for direct driving of the light electric vehicles. The reluctant motor take into study is of special construction suitable for direct drive of a light electric vehicle. It is an inverse radial reluctant motor, with a fixed stator mounted on front wheel shaft and an external toothed rotor fixed on the front wheel itself. A short presentation of preliminary design is continued with the FEM analysis in order to provide the optimal geometry of the motor and adequate windings.

Driving Pattern Analysis for Electric Vehicle (EV) Grid Integration Study

DEFF Research Database (Denmark)

Wu, Qiuwei; Nielsen, Arne Hejde; Østergaard, Jacob

2010-01-01

In order to facilitate the integration of electric vehicles (EVs) into the Danish power system, the driving data in Denmark were analyzed to extract the information of driving distances and driving time periods which were used to represent the driving requirements and the EV unavailability...... from the driving time periods to show how many cars are available for charging and discharging in each time period. The obtained EV availability data are in one hour time periods and one quarter time periods for different study purposes. The EV availability data of one hour time period are to be used...

Oscillation control system for electric motor drive

Science.gov (United States)

Slicker, J.M.; Sereshteh, A.

1988-08-30

A feedback system for controlling mechanical oscillations in the torsionally complaint drive train of an electric or other vehicle. Motor speed is converted in a processor to estimate state signals in which a plant model which are used to electronically modify the torque commands applied to the motor. 5 figs.

The eco-driving effect of electric vehicles compared to conventional gasoline vehicles

Directory of Open Access Journals (Sweden)

Hideki Kato

2016-10-01

Full Text Available Eco-driving is attractive to the public, not only users of internal-combustion-engine vehicles (ICEVs including hybrid electric vehicles (HEVs but also users of electric vehicles (EVs have interest in eco-driving. In this context, a quantitative evaluation of eco-driving effect of EVs was conducted using a chassis dynamometer (C/D with an “eco-driving test mode.” This mode comprised four speed patterns selected from fifty-two real-world driving datasets collected during an eco-driving test-ride event. The four patterns had the same travel distance (5.2 km, but showed varying eco-driving achievement levels. Three ICEVs, one HEV and two EVs were tested using a C/D. Good linear relationships were found between the eco-driving achievement level and electric or fuel consumption rate of all vehicles. The reduction of CO2 emissions was also estimated. The CO2-reduction rates of the four conventional (including hybrid vehicles were 10.9%–12.6%, while those of two types of EVs were 11.7%–18.4%. These results indicate that the eco-driving tips for conventional vehicles are effective to not only ICEVs and HEVs but also EVs. Furthermore, EVs have a higher potential of eco-driving effect than ICEVs and HEVs if EVs could maintain high energy conversion efficiency at low load range. This study is intended to support the importance of the dissemination of tools like the intelligent speed adaptation (ISA to obey the regulation speed in real time. In the future, also in the development and dissemination of automated driving systems, the viewpoint of achieving the traveling purpose with less kinetic energy would be important.

A novel design and driving strategy for a hybrid electric machine with torque performance enhancement both taking reluctance and electromagnetic attraction effects into account

International Nuclear Information System (INIS)

Huang, W.-N.; Chen, W.-P.; Teng, C.-C.; Chen, M.-P.

2006-01-01

A novel design, the hybrid electric machine, that owns improved competence for the output torque regulation as well as enlarged power density comparing to the conventional brushless machines by making use of the simultaneous performance overlapping concept based on magnetism is proposed in this paper. The developed design concept is focused on electric machine structure and its counterpart drive for applying two main magnetic-power transmitting paths by combination of both features of magnetic tendencies of flux generation that may flow in the path with minimum reluctance and direction owning the electromagnetic motive attraction. The verifications demonstrate that the outputted torque owns effective improvement by the presented concept of the electric machine based on the equivalent 3-hp frame than the conventional brushless motors

Bidirectional DC-DC converter fed drive for electric vehicle system ...

African Journals Online (AJOL)

Batteries are the primary energy-storage devices in ground vehicles. Now days battery fed electric drives are commonly being used for electric vehicles applications, due to various advantages, such as: nearly zero emission, guaranteed load leveling, good transient operation and energy recovery during braking operation.

Design of driving control strategy of torque distribution for two - wheel independent drive electric vehicle

Science.gov (United States)

Zhang, Chuanwei; Zhang, Dongsheng; Wen, Jianping

2018-02-01

In order to coordinately control the torque distribution of existing two-wheel independent drive electric vehicle, and improve the energy efficiency and control stability of the whole vehicle, the control strategies based on fuzzy control were designed which adopt the direct yaw moment control as the main line. For realizing the torque coordination simulation of the two-wheel independent drive vehicle, the vehicle model, motor model and tire model were built, including the vehicle 7 - DOF dynamics model, motion equation, torque equation. Finally, in the Carsim - Simulink joint simulation platform, the feasibility of the drive control strategy was verified.

Analysis and control of excitation, field weakening and stability in direct torque controlled electrically excited synchronous motor drives

Energy Technology Data Exchange (ETDEWEB)

Pyrhoenen, O

1999-12-31

Direct torque control (DTC) is a new control method for rotating field electrical machines. DTC controls directly the motor stator flux linkage with the stator voltage, and no stator current controllers are used. With the DTC method very good torque dynamics can be achieved. Until now, DTC has been applied to asynchronous motor drives. The purpose of this work is to analyse the applicability of DTC to electrically excited synchronous motor drives. Compared with asynchronous motor drives, electrically excited synchronous motor drives require an additional control for the rotor field current. The field current control is called excitation control in this study. The dependence of the static and dynamic performance of DTC synchronous motor drives on the excitation control has been analysed and a straightforward excitation control method has been developed and tested. In the field weakening range the stator flux linkage modulus must be reduced in order to keep the electro motive force of the synchronous motor smaller than the stator voltage and in order to maintain a sufficient voltage reserve. The dynamic performance of the DTC synchronous motor drive depends on the stator flux linkage modulus. Another important factor for the dynamic performance in the field weakening range is the excitation control. The field weakening analysis considers both dependencies. A modified excitation control method, which maximises the dynamic performance in the field weakening range, has been developed. In synchronous motor drives the load angle must be kept in a stabile working area in order to avoid loss of synchronism. The traditional vector control methods allow to adjust the load angle of the synchronous motor directly by the stator current control. In the DTC synchronous motor drive the load angle is not a directly controllable variable, but it is formed freely according to the motor`s electromagnetic state and load. The load angle can be limited indirectly by limiting the torque

Analysis and control of excitation, field weakening and stability in direct torque controlled electrically excited synchronous motor drives

Energy Technology Data Exchange (ETDEWEB)

Pyrhoenen, O.

1998-12-31

Direct torque control (DTC) is a new control method for rotating field electrical machines. DTC controls directly the motor stator flux linkage with the stator voltage, and no stator current controllers are used. With the DTC method very good torque dynamics can be achieved. Until now, DTC has been applied to asynchronous motor drives. The purpose of this work is to analyse the applicability of DTC to electrically excited synchronous motor drives. Compared with asynchronous motor drives, electrically excited synchronous motor drives require an additional control for the rotor field current. The field current control is called excitation control in this study. The dependence of the static and dynamic performance of DTC synchronous motor drives on the excitation control has been analysed and a straightforward excitation control method has been developed and tested. In the field weakening range the stator flux linkage modulus must be reduced in order to keep the electro motive force of the synchronous motor smaller than the stator voltage and in order to maintain a sufficient voltage reserve. The dynamic performance of the DTC synchronous motor drive depends on the stator flux linkage modulus. Another important factor for the dynamic performance in the field weakening range is the excitation control. The field weakening analysis considers both dependencies. A modified excitation control method, which maximises the dynamic performance in the field weakening range, has been developed. In synchronous motor drives the load angle must be kept in a stabile working area in order to avoid loss of synchronism. The traditional vector control methods allow to adjust the load angle of the synchronous motor directly by the stator current control. In the DTC synchronous motor drive the load angle is not a directly controllable variable, but it is formed freely according to the motor`s electromagnetic state and load. The load angle can be limited indirectly by limiting the torque

Driving forces and barriers to improved energy performance of buildings: an analysis of energy performance of Swedish buildings, 2000-2006

Energy Technology Data Exchange (ETDEWEB)

Fuglseth, Bente Beckstroem

2008-06-15

The building sector is responsible for a substantial part of energy use and green house gas emissions in Europe. This report explores driving forces and barriers to improved energy performance of buildings, using the Swedish building sector as a case. The development of energy performance of buildings in Sweden from 2000 until 2006 is explored by applying a threefold understanding of energy performance of buildings: substitution from fossil fuels to renewable energy, conversion from electrical heating to thermal energy and reduction in energy demand. Three explanatory approaches are used to analyse driving forces and barriers to improved energy performance: the techno-economic approach stresses the physical aspects of infrastructure and technologies, the institutional approach emphasizes the role of institutional factors, while the regulative approach focuses on formal rules and laws. The study concludes that all factors have promoted substitution of fossil fuels with renewable energy, while they have prevented conversion from electrical heating to thermal energy and reduction in energy demand. (author). 95 refs

Electric and pneumatic drives in an exact comparison; Elektrische und pneumatische Antriebe im exakten Vergleich

Energy Technology Data Exchange (ETDEWEB)

Volk, Roland [Festo AG und Co. KG, Esslingen (Germany)

2013-04-01

The question, whether a pneumatic drive is more energy efficient than an electric drive, is very difficult to answer straightaway. In the automation technology, the energy efficiency always depends on the respective industrial application. Only the direct comparison of an electric and pneumatic drive having the same dimension in different conceptual formulations clears up with prejudices.

Frequency and time domain characteristics of digital control of electric vehicle in-wheel drives

Directory of Open Access Journals (Sweden)

Jarzebowicz Leszek

2017-12-01

Full Text Available In-wheel electric drives are promising as actuators in active safety systems of electric and hybrid vehicles. This new function requires dedicated control algorithms, making it essential to deliver models that reflect better the wheel-torque control dynamics of electric drives. The timing of digital control events, whose importance is stressed in current research, still lacks an analytical description allowing for modeling its influence on control system dynamics. In this paper, authors investigate and compare approaches to the analog and discrete analytical modeling of torque control loop in digitally controlled electric drive. Five different analytical models of stator current torque component control are compared to judge their accuracy in representing drive control dynamics related to the timing of digital control events. The Bode characteristics and stepresponse characteristics of the analytical models are then compared with those of a reference model for three commonly used cases of motor discrete control schemes. Finally, the applicability of the presented models is discussed.

A Universal Educational and Research Stand to Simulate Electrical Drive Loading

Directory of Open Access Journals (Sweden)

V. S. Grishin

2016-01-01

Full Text Available Universal educational and research stand was developed for analyzing an electrical drive’s behavior with different load disturbance effects. Major components of the stand are two electrical drives with rigidly coupled shafts. As a result, first electrical drive (loader has a capability to imitate effects of different loading types to another one (trial drive.Control software for the stand is developed. It allows us to combine a variety of loading types and change parameters of current loading such as joint moment, damping, additional inertia, and external torque. Also there is a capability to imitate effects of elasticity and backlash of mechanical transmissions. The paper considers the main challenge of creating the given system, i.e. discretization with a variable step. Some methods to decrease its negative effects on system stability are suggested.The given system allows to change loading parameters more rapidly and in a wider range as compared to a system with real mechanical outfit.These stands are currently used for laboratory classes within the course “Electrical robotic drives” at SM7 department in Bauman Moscow State Technical University. Also the system of interdepended stands for semi-realistic simulation of manipulation systems is under development.

Novel control algorithm of braking energy regeneration system for an electric vehicle during safety–critical driving maneuvers

International Nuclear Information System (INIS)

Lv, Chen; Zhang, Junzhi; Li, Yutong; Yuan, Ye

2015-01-01

Highlights: • Models of an electric vehicle with regenerative braking system (RBS) are built. • Control algorithm of RBS under safety–critical driving maneuvers is proposed. • Simulations and HIL tests of the proposed strategy are conducted. • Performance improvement of vehicle’s mean deceleration is up to 13.89%. • Test results verify the feasibility and effectiveness of the proposed method. - Abstract: This paper mainly focuses on control algorithm of the braking energy regeneration system of an electric bus under safety–critical driving situations. With the aims of guaranteeing vehicle stability in various types of tyre–road adhesion conditions, based on the characteristics of electrified powertrain, a novel control algorithm of regenerative braking system is proposed for electric vehicles during anti-lock braking procedures. First, the models of vehicle dynamics and main components including braking energy regenerative system of the case-study electric bus are built in MATLAB/Simulink. Then, based on the phase-plane method, the optimal brake torque is calculated for ABS control of vehicle. Next, a novel allocation strategy, wherein the target optimal brake torque is divided into two parts that are handled separately by the regenerative and friction brakes, is developed. Simulations of the proposed control strategy are conducted based on system models built using MATLAB/Simulink. The simulation results demonstrate that the developed strategy enables improved control in terms of vehicle stability and braking performance under different emergency driving conditions. To further verify the synthesized control algorithm, hardware-in-the-loop tests are also performed. The experimental results validate the simulation data and verify the feasibility and effectiveness of the developed control algorithm.

Driving-behavior-aware stochastic model predictive control for plug-in hybrid electric buses

International Nuclear Information System (INIS)

Li, Liang; You, Sixiong; Yang, Chao; Yan, Bingjie; Song, Jian; Chen, Zheng

2016-01-01

Highlights: • The novel approximated global optimal energy management strategy has been proposed for hybrid powertrains. • Eight typical driving behaviors have been classified with K-means to deal with the multiplicative traffic conditions. • The stochastic driver models of different driving behaviors were established based on the Markov chains. • ECMS was used to modify the SMPC-based energy management strategy to improve its fuel economy. • The approximated global optimal energy management strategy for plug-in hybrid electric buses has been verified and analyzed. - Abstract: Driving cycles of a city bus is statistically characterized by some repetitive features, which makes the predictive energy management strategy very desirable to obtain approximate optimal fuel economy of a plug-in hybrid electric bus. But dealing with the complicated traffic conditions and finding an approximated global optimal strategy which is applicable to the plug-in hybrid electric bus still remains a challenging technique. To solve this problem, a novel driving-behavior-aware modified stochastic model predictive control method is proposed for the plug-in hybrid electric bus. Firstly, the K-means is employed to classify driving behaviors, and the driver models based on Markov chains is obtained under different kinds of driving behaviors. While the obtained driver behaviors are regarded as stochastic disturbance inputs, the local minimum fuel consumption might be obtained with a traditional stochastic model predictive control at each step, taking tracking the reference battery state of charge trajectory into consideration in the finite predictive horizons. However, this technique is still accompanied by some working points with reduced/worsened fuel economy. Thus, the stochastic model predictive control is modified with the equivalent consumption minimization strategy to eliminate these undesirable working points. The results in real-world city bus routines show that the

Assessment of driving-related performance in chronic whiplash using an advanced driving simulator.

Science.gov (United States)

Takasaki, Hiroshi; Treleaven, Julia; Johnston, Venerina; Rakotonirainy, Andry; Haines, Andrew; Jull, Gwendolen

2013-11-01

Driving is often nominated as problematic by individuals with chronic whiplash associated disorders (WAD), yet driving-related performance has not been evaluated objectively. The purpose of this study was to test driving-related performance in persons with chronic WAD against healthy controls of similar age, gender and driving experience to determine if driving-related performance in the WAD group was sufficiently impaired to recommend fitness to drive assessment. Driving-related performance was assessed using an advanced driving simulator during three driving scenarios; freeway, residential and a central business district (CBD). Total driving duration was approximately 15min. Five driving tasks which could cause a collision (critical events) were included in the scenarios. In addition, the effect of divided attention (identify red dots projected onto side or rear view mirrors) was assessed three times in each scenario. Driving performance was measured using the simulator performance index (SPI) which is calculated from 12 measures. z-Scores for all SPI measures were calculated for each WAD subject based on mean values of the control subjects. The z-scores were then averaged for the WAD group. A z-score of ≤-2 indicated a driving failing grade in the simulator. The number of collisions over the five critical events was compared between the WAD and control groups as was reaction time and missed response ratio in identifying the red dots. Seventeen WAD and 26 control subjects commenced the driving assessment. Demographic data were comparable between the groups. All subjects completed the freeway scenario but four withdrew during the residential and eight during the CBD scenario because of motion sickness. All scenarios were completed by 14 WAD and 17 control subjects. Mean z-scores for the SPI over the three scenarios was statistically lower in the WAD group (-0.3±0.3; Pdriving. There were no differences in the reaction time and missed response ratio in divided

Downward Slope Driving Control for Electric Powered Wheelchair Based on Capacitor Regenerative Brake

Science.gov (United States)

Seki, Hirokazu; Takahashi, Yoshiaki

This paper describes a novel capacitor regenerative braking control scheme of electric powered wheelchairs for efficient driving on downward slopes. An electric powered wheelchair, which generates the driving force by electric motors, is expected to be widely used as a mobility support system for elderly people and disabled people; however the energy efficiency has to be further improved because it is driven only by battery energy. This study proposes a capacitor regenerative braking circuit and two types of velocity control schemes with variable duty ratio. The proposed regenerative braking circuit is based on the step-up/down circuit with additional resistance and connects right and left motors in series in order to obtain a larger braking power. Some driving experiments on a practical downward slope show the effectiveness of the proposed control system.

Optimal recharge and driving strategies for a battery-powered electric vehicle

Directory of Open Access Journals (Sweden)

Lee W. R.

1999-01-01

Full Text Available A major problem facing battery-powered electric vehicles is in their batteries: weight and charge capacity. Thus, a battery-powered electric vehicle only has a short driving range. To travel for a longer distance, the batteries are required to be recharged frequently. In this paper, we construct a model for a battery-powered electric vehicle, in which driving strategy is to be obtained such that the total travelling time between two locations is minimized. The problem is formulated as an optimization problem with switching times and speed as decision variables. This is an unconventional optimization problem. However, by using the control parametrization enhancing technique (CPET, it is shown that this unconventional optimization is equivalent to a conventional optimal parameter selection problem. Numerical examples are solved using the proposed method.

Study and performances analysis of fuel cell assisted vector control variable speed drive system used for electric vehicles

Science.gov (United States)

Pachauri, Rupendra Kumar; Chauhan, Yogesh K.

2017-02-01

This paper is a novel attempt to combine two important aspects of fuel cell (FC). First, it presents investigations on FC technology and its applications. A description of FC operating principles is followed by the comparative analysis of the present FC technologies together with the issues concerning various fuels. Second, this paper also proposes a model for the simulation and performances evaluation of a proton exchange membrane fuel cell (PEMFC) generation system. Furthermore, a MATLAB/Simulink-based dynamic model of PEMFC is developed and parameters of FC are so adjusted to emulate a commercially available PEMFC. The system results are obtained for the PEMFC-driven adjusted speed induction motor drive (ASIMD) system, normally used in electric vehicles and analysis is carried out for different operating conditions of FC and ASIMD system. The obtained results prove the validation of system concept and modelling.

Modeling Driving Performance Using In-Vehicle Speech Data From a Naturalistic Driving Study.

Science.gov (United States)

Kuo, Jonny; Charlton, Judith L; Koppel, Sjaan; Rudin-Brown, Christina M; Cross, Suzanne

2016-09-01

We aimed to (a) describe the development and application of an automated approach for processing in-vehicle speech data from a naturalistic driving study (NDS), (b) examine the influence of child passenger presence on driving performance, and (c) model this relationship using in-vehicle speech data. Parent drivers frequently engage in child-related secondary behaviors, but the impact on driving performance is unknown. Applying automated speech-processing techniques to NDS audio data would facilitate the analysis of in-vehicle driver-child interactions and their influence on driving performance. Speech activity detection and speaker diarization algorithms were applied to audio data from a Melbourne-based NDS involving 42 families. Multilevel models were developed to evaluate the effect of speech activity and the presence of child passengers on driving performance. Speech activity was significantly associated with velocity and steering angle variability. Child passenger presence alone was not associated with changes in driving performance. However, speech activity in the presence of two child passengers was associated with the most variability in driving performance. The effects of in-vehicle speech on driving performance in the presence of child passengers appear to be heterogeneous, and multiple factors may need to be considered in evaluating their impact. This goal can potentially be achieved within large-scale NDS through the automated processing of observational data, including speech. Speech-processing algorithms enable new perspectives on driving performance to be gained from existing NDS data, and variables that were once labor-intensive to process can be readily utilized in future research. © 2016, Human Factors and Ergonomics Society.

Performance Analysis of Hybrid Electric Vehicle over Different Driving Cycles

Science.gov (United States)

Panday, Aishwarya; Bansal, Hari Om

2017-02-01

Article aims to find the nature and response of a hybrid vehicle on various standard driving cycles. Road profile parameters play an important role in determining the fuel efficiency. Typical parameters of road profile can be reduced to a useful smaller set using principal component analysis and independent component analysis. Resultant data set obtained after size reduction may result in more appropriate and important parameter cluster. With reduced parameter set fuel economies over various driving cycles, are ranked using TOPSIS and VIKOR multi-criteria decision making methods. The ranking trend is then compared with the fuel economies achieved after driving the vehicle over respective roads. Control strategy responsible for power split is optimized using genetic algorithm. 1RC battery model and modified SOC estimation method are considered for the simulation and improved results compared with the default are obtained.

Three-phase electric drive with modified electronic smoothing inductor

DEFF Research Database (Denmark)

Singh, Yash Veer; Rasmussen, Peter Omand; Andersen, Torben Ole

2010-01-01

This paper presents a three-phase electric drive with a modified electronic smoothing inductor (MESI) having reduced size of passive components. The classical electronic smoothing inductor (ESI) is able to control a diode bridge output current and also reduce not only mains current harmonics...

Harnessing Big-Data for Estimating the Energy Consumption and Driving Range of Electric Vehicles

DEFF Research Database (Denmark)

Fetene, Gebeyehu Manie; Prato, Carlo Giacomo; Kaplan, Sigal

-effects econometrics model used in this paper predicts that the energy saving speed of driving is between 45 and 56 km/h. In addition to the contribution to the literature about energy efficiency of electric vehicles, the findings from this study enlightens consumers to choose appropriate cars that suit their travel......This study analyses the driving range and investigates the factors affecting the energy consumption rate of fully-battery electric vehicles under real-world driving patterns accounting for weather condition, drivers’ characteristics, and road characteristics. Four data sources are used: (i) up...

Drive Stands

Data.gov (United States)

Federal Laboratory Consortium — The Electrical Systems Laboratory (ESL)houses numerous electrically driven drive stands. A drive stand consists of an electric motor driving a gearbox and a mounting...

Near-term hybrid vehicle program, phase 1. Appendix B: Design trade-off studies. [various hybrid/electric power train configurations and electrical and mechanical drive-line components

Science.gov (United States)

1979-01-01

The relative attractiveness of various hybrid/electric power train configurations and electrical and mechanical drive-line components was studied. The initial screening was concerned primarily with total vehicle weight and economic factors and identified the hybrid power train combinations which warranted detailed evaluation over various driving cycles. This was done using a second-by-second vehicle simulation program which permitted the calculations of fuel economy, electricity usage, and emissions as a function of distance traveled in urban and highway driving. Power train arrangement possibilities were examined in terms of their effect on vehicle handling, safety, serviceability, and passenger comfort. A dc electric drive system utilizing a separately excited motor with field control and battery switching was selected for the near term hybrid vehicle. Hybrid vehicle simulations showed that for the first 30 mi (the electric range of the vehicle) in urban driving, the fuel economy was 80 mpg using a gasoline engine and 100 mpg using a diesel engine. In urban driving the hybrid would save about 75% of the fuel used by the conventional vehicle and in combined urban/highway driving the fuel saving is about 50%.

Correspondence between Simulator and On-Road Drive Performance: Implications for Assessment of Driving Safety.

Science.gov (United States)

Aksan, Nazan; Hacker, Sarah D; Sager, Lauren; Dawson, Jeffrey; Anderson, Steven; Rizzo, Matthew

2016-03-01

Forty-two younger (Mean age = 35) and 37 older drivers (Mean age = 77) completed four similar simulated drives. In addition, 32 younger and 30 older drivers completed a standard on-road drive in an instrumented vehicle. Performance in the simulated drives was evaluated using both electronic drive data and video-review of errors. Safety errors during the on-road drive were evaluated by a certified driving instructor blind to simulator performance, using state Department of Transportation criteria. We examined the degree of convergence in performance across the two platforms on various driving tasks including lane change, lane keeping, speed control, stopping, turns, and overall performance. Differences based on age group indicated a pattern of strong relative validity for simulator measures. However, relative rank-order in specific metrics of performance suggested a pattern of moderate relative validity. The findings have implications for the use of simulators in assessments of driving safety as well as its use in training and/or rehabilitation settings.

Variable-Reluctance Motor For Electric Vehicles

Science.gov (United States)

Lang, Jeffrey H.

1987-01-01

Report describes research on variable-reluctance electric-motor drive for eventual use in electric-vehicle propulsion. Primary design and performance criteria were torque and power output per unit mass of motor, cost, and drive efficiency. For each criterion, optimized drive design developed, and designs unified to yield single electric-vehicle drive. Scaled-down motor performed as expected. Prototype of paraplegic lift operated by toggle switch and joystick. Lift plugs into household electrical outlet for recharging when not in use.

Integrated traction control strategy for distributed drive electric vehicles with improvement of economy and longitudinal driving stability

OpenAIRE

Zhang, Xudong; Göhlich, Dietmar

2017-01-01

This paper presents an integrated traction control strategy (ITCS) for distributed drive electric vehicles. The purpose of the proposed strategy is to improve vehicle economy and longitudinal driving stability. On high adhesion roads, economy optimization algorithm is applied to maximize motors efficiency by means of the optimized torque distribution. On low adhesion roads, a sliding mode control (SMC) algorithm is implemented to guarantee the wheel slip ratio around the optimal slip ratio po...

Integrated Vehicle Thermal Management - Combining Fluid Loops in Electric Drive Vehicles (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Rugh, J. P.

2013-07-01

Plug-in hybrid electric vehicles and electric vehicles have increased vehicle thermal management complexity, using separate coolant loop for advanced power electronics and electric motors. Additional thermal components result in higher costs. Multiple cooling loops lead to reduced range due to increased weight. Energy is required to meet thermal requirements. This presentation for the 2013 Annual Merit Review discusses integrated vehicle thermal management by combining fluid loops in electric drive vehicles.

REDUCING ENERGY CONSUMPTION BY PASSENGER CAR WITH USING OF NON-ELECTRICAL HYBRID DRIVE TECHNOLOGY

Directory of Open Access Journals (Sweden)

Tomas Skrucany

2017-03-01

Full Text Available Not only electrical hybrid technology is used for drivetrain of passenger cars. Also other systems using non-electrical principles (hydraulic or air pressure, mechanical energy storage can be found in current vehicles. There is a quantification of the spared energy by using a hybrid vehicle in the paper. Driving cy-cle ECE 15 was chosen as a platform for simulation of driving resistances.

Simulation and Implementation of Sensorless Control in Multi-Motors Electric Drives with High Dynamics

Directory of Open Access Journals (Sweden)

Marcel Nicola

2017-05-01

Full Text Available In this article we’ll tackle the control of multi-motors electric drives with high dynamic, with rapid changes in torque and speed, with rigid or flexible coupling of motors, where the control strategy is FOC (Field Oriented Control for each drives and the distributed control in local network using the CANopen protocol. In the surface mining industry, from which the electric drive application for this article is selected, the general trend is toward using asynchronous motors with short-circuit rotor, due to the advantages of this motor both in terms of design and operation. In order to achieve the variable speed, must be used the static frequency converters with sensorless control, where speed is estimated using a Model References Adaptive Control Estimator. The global control system proposed in this paper contain this type of MRAC estimator together with PI-control based, who ensures a good dynamic performance but in a lower complexity of structure such that are properly to implement in real time in a distributed control system with DSP in local network using the CANopen protocol with advantages in terms of software technology, as well as control cost and flexibility of use. Following these directions a functional application was implemented and tested in practice.

Replacement of pneumatic and hydraulic drives with electrical drives - Analysis of potential; Ersatz von pneumatischen und hydraulischen Antrieben durch Elektroantriebe. Potentialanalyse

Energy Technology Data Exchange (ETDEWEB)

Berchten, S. [BEngineering, Bassersdorf (Switzerland); Ritz, Ch. [Schnyder Ingenieure AG, Steg (Switzerland)

2006-07-01

This final report for the Swiss Federal Office of Energy (SFOE) discusses the potential offered by modern technologies to save energy. The replacement of energy-intensive methods of providing physical movement - such as with pneumatic and hydraulic drives - with electrical drives is discussed. Based on existing installations in industry, an estimate of the potential for making savings is presented. This shows that large energy savings can be made by directly converting electrical into mechanical energy. Using real world examples, end-users and decision-makers are shown two profit-scenarios involving the purchase of a new system or retrofitting an existing system. The scenarios take investments, operating costs and system life-cycle into account. Extrapolations provide estimates of savings-potentials for the Swiss electricity market. Various market sectors are looked at, including the metal-working, chemical, foodstuffs and packaging sectors. Examples of installations actually implemented, where electro-mechanical systems have replaced pneumatic and hydraulic drives, are given.

On the Application of TLS Techniques to AC Electrical Drives

Directory of Open Access Journals (Sweden)

M. Cirrincione

2005-03-01

Full Text Available This paper deals with the application of a new neuron, the TLS EXIN neuron, to AC induction motor drives. In particular, it addresses two important subjects of AC induction motor drives: the on-line estimation of the electrical parameters of the machine and the speed estimation in sensorless drives. On this basis, this work summarizes the parameter estimation and sensorless techniques already developed by the authors over these last few years, all based on the TLS EXIN. With regard to sensorless, two techniques are proposed: one based on the MRAS and the other based on the full-order Luenberger observer. The work show some of the most significant results obtained by the authors in these fields and stresses the important potentiality of this new neural technique in AC induction machine drives.

Marijuana and actual driving performance

Science.gov (United States)

1993-11-01

This report concerns the effects of marijuana smoking on actual driving performance. It presents the results of one pilot and three actual driving studies. The pilot study's major purpose was to establish the THC dose current marijuana users smoke to...

Electric drive motors for industrial robots

Science.gov (United States)

Fichtner, K.

1985-04-01

In robotized industrial plants it is possible to use electric motors in the technological process and also for control, assembly, transport, testing, and measurements. Particularly suitable for these applications are permanent-magnet d.c. motors. A new special series was developed for industrial robots with hinge joints in kinematic pairs. The complete drive includes thyristors or transistor controls with regulators and, if necessary, a line transformer as well as a servomotor with tachometer and odometer for speed, current, and position control. The drive is coupled to a robot tong through mechanical torque and force converters. In addition to a 0 to 4000 rpm speed regulation, without wobble at low speeds, and a high torque-to-weight ratio for repetitive short-time heavy duty, these low-inertia motors develop high starting and accelerating torques over the entire speed range. They operate from a 1 to O 220 V a.c. line through a rectifier. The motors are totally enclosed, or of open construction for better ventilation. Their windings have class F insulation for operation at ambient temperatures up to 40 C.

Multifunctional Converter Drive for Automotive Electric Power Steering Systems

NARCIS (Netherlands)

Hackner, T.J.

2013-01-01

In this thesis it is shown that in the case of an automotive electric power steering system, critical pulse power loads can be decoupled from the power net with a storage element and a multifunctional converter. A multifunctional converter system is proposed because it uses the motor drive system as

REDUNDANT ELECTRIC MOTOR DRIVE CONTROL UNIT DESIGN USING AUTOMATA-BASED APPROACH

Directory of Open Access Journals (Sweden)

Yuri Yu. Yankin

2014-11-01

Full Text Available Implementation of redundant unit for motor drive control based on programmable logic devices is discussed. Continuous redundancy method is used. As compared to segregated standby redundancy and whole system standby redundancy, such method provides preservation of all unit functions in case of redundancy and gives the possibility for continuous monitoring of major and redundant elements. Example of that unit is given. Electric motor drive control channel block diagram contains two control units – the major and redundant; it also contains four power supply units. Control units programming was carried out using automata-based approach. Electric motor drive control channel model was developed; it provides complex simulation of control state-machine and power converter. Through visibility and hierarchy of finite state machines debug time was shortened as compared to traditional programming. Control state-machine description using hardware description language is required for its synthesis with FPGA-devices vendor design software. This description was generated automatically by MATLAB software package. To verify results two prototype control units, two prototype power supply units, and device mock-up were developed and manufactured. Units were installed in the device mock-up. Prototype units were created in accordance with requirements claimed to deliverable hardware. Control channel simulation and tests results in the perfect state and during imitation of major element fault are presented. Automata-based approach made it possible to observe and debug control state-machine transitions during simulation of transient processes, occurring at imitation of faults. Results of this work can be used in development of fault tolerant electric motor drive control channels.

Stochastic optimal charging of electric-drive vehicles with renewable energy

International Nuclear Information System (INIS)

Pantoš, Miloš

2011-01-01

The paper presents the stochastic optimization algorithm that may eventually be used by electric energy suppliers to coordinate charging of electric-drive vehicles (EDVs) in order to maximize the use of renewable energy in transportation. Due to the stochastic nature of transportation patterns, the Monte Carlo simulation is applied to model uncertainties presented by numerous scenarios. To reduce the problem complexity, the simulated driving patterns are not individually considered in the optimization but clustered into fleets using the GAMS/SCENRED tool. Uncertainties of production of renewable energy sources (RESs) are presented by statistical central moments that are further considered in Hong’s 2-point + 1 estimation method in order to define estimate points considered in the optimization. Case studies illustrate the application of the proposed optimization in achieving maximal exploitation of RESs in transportation by EDVs. -- Highlights: ► Optimization model for EDV charging applying linear programming. ► Formation of EDV fleets based on the driving patterns assessment applying the GAMS/SCENRED. ► Consideration of uncertainties of RES production and energy prices in the market. ► Stochastic optimization. ► Application of Hong’s 2-point + 1 estimation method.

Reducing Energy Demand Using Wheel-Individual Electric Drives to Substitute EPS-Systems

Directory of Open Access Journals (Sweden)

Jürgen Römer

2018-01-01

Full Text Available The energy demand of vehicles is influenced, not only by the drive systems, but also by a number of add-on systems. Electric vehicles must satisfy this energy demand completely from the battery. Hence, the use of power steering systems directly result in a range reduction. The “e2-Lenk” joint project funded by the German Federal Ministry of Education and Research (BMBF involves a novel steering concept for electric vehicles to integrate the function of steering assistance into the drive-train. Specific distribution of driving torque at the steered axle allows the steering wheel torque to be influenced to support the steering force. This provides a potential for complete substitution of conventional power steering systems and reduces the vehicle’s energy demand. This paper shows the potential of wheel-individual drives influencing the driver’s steering torque using a control technique based on classical EPS control plans. Compared to conventional power-assisted steering systems, a reduced energy demand becomes evident over a wide range of operating conditions.

Energy-efficient control of a multi-section supercapacitor power supply of an electric drive

Directory of Open Access Journals (Sweden)

Mozzhechkov Vladimir

2018-01-01

Full Text Available A method for synthesizing the control laws of a multi-section supercapacitor power supply of an electric drive is developed. The synthesized control law for an electric drive realizes the prescribed motion and minimizes the required capacitance of the power source. It is achieved through optimal disconnection and connection to the power line of the drive at designated times of one of the power supply sections. Reduction of the required capacitance of the power supply is achieved through a fuller discharge of some of its sections in motion conditions requiring a low level of electrical voltage and saving high voltage in other sections for the respective motion conditions. A mathematical formulation of the problem and a method of its solution is proposed. An example of the implementation of the proposed method is considered.

Performance of batteries for electric vehicles on short and longer term

NARCIS (Netherlands)

Gerssen - Gondelach, Sarah|info:eu-repo/dai/nl/355262436; Faaij, André P C|info:eu-repo/dai/nl/10685903X

2012-01-01

In this work, the prospects of available and new battery technologies for battery electric vehicles (BEVs) are examined. Five selected battery technologies are assessed on battery performance and cost in the short, medium and long term. Driving cycle simulations are carried out to assess the

Performance of Batteries for electric vehicles on shorter and longer term

NARCIS (Netherlands)

Gerssen-Gondelach, S.J.; Faaij, A.P.C.

2012-01-01

In this work, the prospects of available and new battery technologies for battery electric vehicles (BEVs) are examined. Five selected battery technologies are assessed on battery performance and cost in the short, medium and long term. Driving cycle simulations are carried out to assess the

Design and analysis of new fault-tolerant permanent magnet motors for four-wheel-driving electric vehicles

Science.gov (United States)

Liu, Guohai; Gong, Wensheng; Chen, Qian; Jian, Linni; Shen, Yue; Zhao, Wenxiang

2012-04-01

In this paper, a novel in-wheel permanent-magnet (PM) motor for four-wheel-driving electrical vehicles is proposed. It adopts an outer-rotor topology, which can help generate a large drive torque, in order to achieve prominent dynamic performance of the vehicle. Moreover, by adopting single-layer concentrated-windings, fault-tolerant teeth, and the optimal combination of slot and pole numbers, the proposed motor inherently offers negligible electromagnetic coupling between different phase windings, hence, it possesses a fault-tolerant characteristic. Meanwhile, the phase back electromotive force waveforms can be designed to be sinusoidal by employing PMs with a trapezoidal shape, eccentric armature teeth, and unequal tooth widths. The electromagnetic performance is comprehensively investigated and the optimal design is conducted by using the finite-element method.

In Patients With Cirrhosis, Driving Simulator Performance Is Associated With Real-life Driving.

Science.gov (United States)

Lauridsen, Mette M; Thacker, Leroy R; White, Melanie B; Unser, Ariel; Sterling, Richard K; Stravitz, Richard T; Matherly, Scott; Puri, Puneet; Sanyal, Arun J; Gavis, Edith A; Luketic, Velimir; Siddiqui, Muhammad S; Heuman, Douglas M; Fuchs, Michael; Bajaj, Jasmohan S

2016-05-01

Minimal hepatic encephalopathy (MHE) has been linked to higher real-life rates of automobile crashes and poor performance in driving simulation studies, but the link between driving simulator performance and real-life automobile crashes has not been clearly established. Furthermore, not all patients with MHE are unsafe drivers, but it is unclear how to distinguish them from unsafe drivers. We investigated the link between performance on driving simulators and real-life automobile accidents and traffic violations. We also aimed to identify features of unsafe drivers with cirrhosis and evaluated changes in simulated driving skills and MHE status after 1 year. We performed a study of outpatients with cirrhosis (n = 205; median 55 years old; median model for end-stage liver disease score, 9.5; none with overt hepatic encephalopathy or alcohol or illicit drug use within previous 6 months) seen at the Virginia Commonwealth University and McGuire Veterans Administration Medical Center, from November 2008 through April 2014. All participants were given paper-pencil tests to diagnose MHE (98 had MHE; 48%), and 163 patients completed a standardized driving simulation. Data were collected on traffic violations and automobile accidents from the Virginia Department of Motor Vehicles and from participants' self-assessments when they entered the study, and from 73 participants 1 year later. Participants also completed a questionnaire about alcohol use and cessation patterns. The driving simulator measured crashes, run-time, road center and edge excursions, and illegal turns during navigation; before and after each driving simulation session, patients were asked to rate their overall driving skills. Drivers were classified as safe or unsafe based on crashes and violations reported on official driving records; simulation results were compared with real-life driving records. Multivariable regression analyses of real-life crashes and violations was performed using data on

Power Management Strategy of Hybrid Electric Vehicles Based on Quadratic Performance Index

Directory of Open Access Journals (Sweden)

Chaoying Xia

2015-11-01

Full Text Available An energy management strategy (EMS considering both optimality and real-time performance has become a challenge for the development of hybrid electric vehicles (HEVs in recent years. Previous EMSes based on the optimal control theory minimize the fuel consumption, but cannot be directly implemented in real-time because of the requirement for a prior knowledge of the entire driving cycle. This paper presents an innovative design concept and method to obtain a power management strategy for HEVs, which is independent of future driving conditions. A quadratic performance index is designed to ensure the vehicle drivability, maintain the battery energy sustainability and average and smooth the engine power and motor power to indirectly reduce fuel consumption. To further improve the fuel economy, two rules are adopted to avoid the inefficient engine operation by switching control modes between the electric and hybrid modes according to the required driving power. The derived power of the engine and motor are related to current vehicle velocity and battery residual energy, as well as their desired values. The simulation results over different driving cycles in Advanced Vehicle Simulator (ADVISOR show that the proposed strategy can significantly improve the fuel economy, which is very close to the optimal strategy based on Pontryagin’s minimum principle.

Turboelectric Aircraft Drive Key Performance Parameters and Functional Requirements

Science.gov (United States)

Jansen, Ralph H.; Brown, Gerald V.; Felder, James L.; Duffy, Kirsten P.

2016-01-01

The purpose of this paper is to propose specific power and efficiency as the key performance parameters for a turboelectric aircraft power system and investigate their impact on the overall aircraft. Key functional requirements are identified that impact the power system design. Breguet range equations for a base aircraft and a turboelectric aircraft are found. The benefits and costs that may result from the turboelectric system are enumerated. A break-even analysis is conducted to find the minimum allowable electric drive specific power and efficiency that can preserve the range, initial weight, operating empty weight, and payload weight of the base aircraft.

An Introduction to Feedforward Control of Electric Drives

Directory of Open Access Journals (Sweden)

Michal Malek

2010-01-01

Full Text Available The field of electric drives provides a broad spectrum of applications with different power demands, utilized motor types or different environment requirements. Lot of applications are characterized by very high demands on accuracy and dynamic properties and have attribute of servo applications. This means that they are fully subordinate to wishes of the master. This rigorous condition is fulfill (with tolerated errors mainly thanks to the feedforward utilization.

Electrical coupling suppression and transient response improvement for a microgyroscope using ascending frequency drive with a 2-DOF PID controller

International Nuclear Information System (INIS)

Cui, J; Guo, Z Y; Yang, Z C; Hao, Y L; Yan, G Z

2011-01-01

In this paper, we demonstrate a novel control strategy for the drive mode of a microgyroscope using ascending frequency drive (AFD) with an AGC-2DOF PID controller, which drives a resonator with a modulation signal not at the resonant frequency and senses the vibration signal at the resonant frequency, thus realizing the isolation between the actual mechanical response and electrical coupling signal. This approach holds the following three advantages: (1) it employs the AFD signal instead of the resonant frequency drive signal to excite the gyroscope in the drive direction, suppressing the electrical coupling from the drive electrode to the sense electrode; (2) it can reduce the noise at low frequency and resonant frequency by shifting flicker noise to the high-frequency part; (3) it can effectively improve the performance of the transient response of the closed-loop control with a 2-DOF (degree of freedom) PID controller compared with the conventional 1-DOF PID. The stability condition of the whole loop is investigated by utilizing the averaging and linearization method. The control approach is applied to drive a lateral tuning fork microgyroscope. Test results show good agreement with the theoretical and simulation results. The non-ideal electrical antiresonance peak is removed and the resonant peak height increases by approximately 10 dB over a 400 Hz span with a flicker noise reduction of 30 dB within 100 Hz using AFD. The percent overshoot is reduced from 36.2% (1DOF PID) to 8.95% (2DOF PID, about 75.3% overshoot suppression) with 15.3% improvement in setting time

Characteristic Evaluation on the Cooling Performance of an Electrical Air Conditioning System Using R744 for a Fuel Cell Electric Vehicle

Directory of Open Access Journals (Sweden)

Moo-Yeon Lee

2012-05-01

Full Text Available The objective of this study was to investigate the cooling performance characteristics of an electrical air conditioning system using R744 as an alternative of R-134a for a fuel cell electric vehicle. In order to analyze the cooling performance characteristics of the air conditioning system using R744 for a fuel cell electric vehicle, an electrical air conditioning system using R744 was developed and tested under various operating conditions according to both inlet air conditions of the gas cooler and evaporator and compressor speed. The cooling capacity and coefficient of performance (COP forcooling of the tested air conditioning system were up to 6.4 kW and 2.5, respectively. In addition, the electrical air conditioning system with R744 using an inverter driven compressor showed better performance than the conventional air conditioning system with R-134a under the same operating conditions. The observed cooling performance of the developed electrical air conditioning system was found to be sufficient for cooling loads under various real driving conditions for a fuel cell electric vehicle.

Single-wheel drive with new electric components. Einzelradantrieb mit neuen E-Komponenten

Energy Technology Data Exchange (ETDEWEB)

Westendorf, H. (Fichtel und Sachs AG, Schweinfurt (Germany)); Schiebold, S. (Fichtel und Sachs AG, Schweinfurt (Germany)); Ehrhart, P. (Fichtel und Sachs AG, Schweinfurt (Germany)); Lindner, L. (Fichtel und Sachs AG, Schweinfurt (Germany))

1991-01-01

Fundamentally important developments and innovations in the fields of magnetic materials, plastics technology and electronics, together with new control concepts, make a new drive concept possible for passenger cars produced in series. The concept, which makes use of a combustion engine and an all-electric power transmission with a single-wheel drive, is presented, together with its components. (orig./HW)

Multi-mode energy management strategy for fuel cell electric vehicles based on driving pattern identification using learning vector quantization neural network algorithm

Science.gov (United States)

Song, Ke; Li, Feiqiang; Hu, Xiao; He, Lin; Niu, Wenxu; Lu, Sihao; Zhang, Tong

2018-06-01

The development of fuel cell electric vehicles can to a certain extent alleviate worldwide energy and environmental issues. While a single energy management strategy cannot meet the complex road conditions of an actual vehicle, this article proposes a multi-mode energy management strategy for electric vehicles with a fuel cell range extender based on driving condition recognition technology, which contains a patterns recognizer and a multi-mode energy management controller. This paper introduces a learning vector quantization (LVQ) neural network to design the driving patterns recognizer according to a vehicle's driving information. This multi-mode strategy can automatically switch to the genetic algorithm optimized thermostat strategy under specific driving conditions in the light of the differences in condition recognition results. Simulation experiments were carried out based on the model's validity verification using a dynamometer test bench. Simulation results show that the proposed strategy can obtain better economic performance than the single-mode thermostat strategy under dynamic driving conditions.

Age and inconsistency in driving performance.

Science.gov (United States)

Bunce, David; Young, Mark S; Blane, Alison; Khugputh, Priya

2012-11-01

Research in cognitive neuropsychology suggests that investigation of the within-person variability, or inconsistency, of cognitive performance may provide valuable insights into ageing mental processes. It is rare though, for this interest in intraindividual variability to extend to everyday activities. As this may provide important information about driving behaviour, we therefore assessed age differences in driving inconsistency in younger (n=24, M age=21.29 years) and older (n=21, M age=71.24 years) persons who drove in residential, urban and motorway conditions in a fully immersive driving simulator. In measures of headway (maintaining a safe distance to a preceding vehicle) and lateral lane position, older drivers exhibited significantly greater performance inconsistency, and this was particularly marked in the faster motorway condition. Older drivers also recorded greater perceived mental demands associated with driving, and greater within-person variability across a range of cognitive measures. The findings suggest that age-related deficits in attentional and executive control may affect the consistency of driving performance in older persons. Discussion considers interventions to introduce in-vehicle systems to help maintain attention in older drivers, and to intervene when safety-critical boundaries are exceeded. Copyright © 2012 Elsevier Ltd. All rights reserved.

Enhanced Regenerative Braking Strategies for Electric Vehicles: Dynamic Performance and Potential Analysis

Directory of Open Access Journals (Sweden)

Boyi Xiao

2017-11-01

Full Text Available A regenerative braking system and hydraulic braking system are used in conjunction in the majority of electric vehicles worldwide. We propose a new regenerative braking distribution strategy that is based on multi-input fuzzy control logic while considering the influences of the battery’s state of charge, the brake strength and the motor speed. To verify the braking performance and recovery economy, this strategy was applied to a battery electric vehicle model and compared with two other improved regenerative braking strategies. The performance simulation was performed using standard driving cycles (NEDC, LA92, and JP1015 and a real-world-based urban cycle in China. The tested braking strategies satisfied the general safety requirements of Europe (as specified in ECE-13H, and the emergency braking scenario and economic potential were tested. The simulation results demonstrated the differences in the braking force distribution performance of these three regenerative braking strategies, the feasibility of the braking methods for the proposed driving cycles and the energy economic potential of the three strategies.

The impact of continuous driving time and rest time on commercial drivers' driving performance and recovery.

Science.gov (United States)

Wang, Lianzhen; Pei, Yulong

2014-09-01

This real road driving study was conducted to investigate the effects of driving time and rest time on the driving performance and recovery of commercial coach drivers. Thirty-three commercial coach drivers participated in the study, and were divided into three groups according to driving time: (a) 2 h, (b) 3 h, and (c) 4 h. The Stanford Sleepiness Scale (SSS) was used to assess the subjective fatigue level of the drivers. One-way ANOVA was employed to analyze the variation in driving performance. The statistical analysis revealed that driving time had a significant effect on the subjective fatigue and driving performance measures among the three groups. After 2 h of driving, both the subjective fatigue and driving performance measures began to deteriorate. After 4 h of driving, all of the driving performance indicators changed significantly except for depth perception. A certain amount of rest time eliminated the negative effects of fatigue. A 15-minute rest allowed drivers to recover from a two-hour driving task. This needed to be prolonged to 30 min for driving tasks of 3 to 4 h of continuous driving. Drivers' attention, reactions, operating ability, and perceptions are all affected in turn after over 2 h of continuous driving. Drivers should take a certain amount of rest to recover from the fatigue effects before they continue driving. Copyright © 2014 National Safety Council and Elsevier Ltd. All rights reserved.

Linear electric machines, drives, and MAGLEVs handbook

CERN Document Server

Boldea, Ion

2013-01-01

Based on author Ion Boldea's 40 years of experience and the latest research, Linear Electric Machines, Drives, and Maglevs Handbook provides a practical and comprehensive resource on the steady improvement in this field. The book presents in-depth reviews of basic concepts and detailed explorations of complex subjects, including classifications and practical topologies, with sample results based on an up-to-date survey of the field. Packed with case studies, this state-of-the-art handbook covers topics such as modeling, steady state, and transients as well as control, design, and testing of li

Monitoring of Carrying Cable in the Well by Electric Drive of Winch at the Logging Works

International Nuclear Information System (INIS)

Odnokopylov, I G; Gneushev, V V; Larioshina, I A

2016-01-01

Emergency situations during logging operations are considered. The necessity of monitoring of the carrying cable in the well was shown, especially at the jet perforation and seismic researches of wells. The way of monitoring of logging cable and geophysical probe by means of the electric drive of tripping works of the logging winch is offered. This method allows timely to identify the wedges of geophysical equipment and the tension of the cable in well without interfering into construction of logging installation by means of algorithmic processing of sensors of electric drive. Research was conducted on the simulation model; these results indirectly confirm the possibility of using of electric drive for monitoring of downhole equipment. (paper)

Monitoring of Carrying Cable in the Well by Electric Drive of Winch at the Logging Works

Science.gov (United States)

Odnokopylov, I. G.; Gneushev, V. V.; Larioshina, I. A.

2016-01-01

Emergency situations during logging operations are considered. The necessity of monitoring of the carrying cable in the well was shown, especially at the jet perforation and seismic researches of wells. The way of monitoring of logging cable and geophysical probe by means of the electric drive of tripping works of the logging winch is offered. This method allows timely to identify the wedges of geophysical equipment and the tension of the cable in well without interfering into construction of logging installation by means of algorithmic processing of sensors of electric drive. Research was conducted on the simulation model; these results indirectly confirm the possibility of using of electric drive for monitoring of downhole equipment.

A Control Law Definition of the Open Loop Stepping Electric Drive

Directory of Open Access Journals (Sweden)

A. B. Krasovskii

2015-01-01

Full Text Available The paper considers an open loop stepping electric drive (SEP with electric crushing of a step and motor fed from the controlled current invertor which should meet the requirement that is to trial a free-form guided trajectory with a split-hair accuracy. It is shown that with traditional programmed control, when the SEP forms motor phase currents of identical amplitude and variable frequency proportional to the set speed of movement, there may be considerable errors reducing a trial accuracy of the set movement trajectory, dynamic indicators provoking oscillatory processes, and even loss of motor synchronism because influence on a dynamic moment of the motor is impossible.The paper offers and proves a new way to define a control algorithm adequate to drive parameters and programmed trajectory of movement, providing error minimization and thereby increasing trial accuracy of set parameters of movement and expanding dynamic capabilities of a drive. The essence of the offered way is to use a modified mathematical model of a drive in d,q coordinates with a motor fed by the current source. In this model a programmed trajectory of movement is chosen as an input action while solving the appropriate equations defines the necessary law of control. The paper describes a developed simulation model of the stepping electric drive in the environment of MATLAB – SIMULINK, which has been used to verify and prove an efficiency of the offered method to define a control law via typical examples.It is established that no error trial of set movement trajectory in case it has breaks (jogs is technically unfeasible, as it demands an infinitely high forcing voltage of the power supply to maintain the instant positive or negative phase shifts of currents formed in the motor windings.The obtained results can be used in designing programmable precision SEPs in robots, numerically controlled machine tools, and assembly equipment.

Driving pattern analysis of Nordic region based on the national travel surveys for electric vehicle integration

DEFF Research Database (Denmark)

Liu, Zhaoxi; Wu, Qiuwei; Christensen, Linda

2015-01-01

to the power system. This paper presents a methodology to transform driving behavior of persons into the one of cars in order to analyze the driving pattern of electric vehicles (EVs) based on the National Travel Surveys. In the proposed methodology, a statistical process is used to obtain the driving behavior......EVs show great potential to cope with the intermittency of renewable energy sources (RES) and provide demand side flexibility required by the smart grid.On the other hand, the EVs will increase the electricity consumption. Large scale integration of EVs will probably have substantial impacts...... of cars by grouping the survey respondents according to the driving license number and car number and mapping the households with similar characteristics. The proposed methodology was used to carry out the driving pattern analysis in the Nordic region. The detailed driving requirements and the charging...

Integrated Traction Control Strategy for Distributed Drive Electric Vehicles with Improvement of Economy and Longitudinal Driving Stability

Directory of Open Access Journals (Sweden)

Xudong Zhang

2017-01-01

Full Text Available This paper presents an integrated traction control strategy (ITCS for distributed drive electric vehicles. The purpose of the proposed strategy is to improve vehicle economy and longitudinal driving stability. On high adhesion roads, economy optimization algorithm is applied to maximize motors efficiency by means of the optimized torque distribution. On low adhesion roads, a sliding mode control (SMC algorithm is implemented to guarantee the wheel slip ratio around the optimal slip ratio point to make full use of road adhesion capacity. In order to avoid the disturbance on slip ratio calculation due to the low vehicle speed, wheel rotational speed is taken as the control variable. Since the optimal slip ratio varies according to different road conditions, Bayesian hypothesis selection is utilized to estimate the road friction coefficient. Additionally, the ITCS is designed for combining the vehicle economy and stability control through three traction allocation cases: economy-based traction allocation, pedal self-correcting traction allocation and inter-axles traction allocation. Finally, simulations are conducted in CarSim and Matlab/Simulink environment. The results show that the proposed strategy effectively reduces vehicle energy consumption, suppresses wheels-skid and enhances the vehicle longitudinal stability and dynamic performance.

Electric drive systems including smoothing capacitor cooling devices and systems

Energy Technology Data Exchange (ETDEWEB)

Dede, Ercan Mehmet; Zhou, Feng

2017-02-28

An electric drive system includes a smoothing capacitor including at least one terminal, a bus bar electrically coupled to the at least one terminal, a thermoelectric device including a first side and a second side positioned opposite the first side, where the first side is thermally coupled to at least one of the at least one terminal and the bus bar, and a cooling element thermally coupled to the second side of the thermoelectric device, where the cooling element dissipates heat from the thermoelectric device.

Chinese carless young drivers' self-reported driving behavior and simulated driving performance.

Science.gov (United States)

Zhang, Qian; Jiang, Zuhua; Zheng, Dongpeng; Man, Dong; Xu, Xunnan

2013-01-01

Carless young drivers refers to those drivers aged between 18 and 25 years who have a driver's license but seldom have opportunities to practice their driving skills because they do not have their own cars. Due to China's lower private car ownership, many young drivers become carless young drivers after licensure, and the safety issue associated with them has raised great concern in China. This study aims to provide initial insight into the self-reported driving behaviors and simulated driving performance of Chinese carless young drivers. Thirty-three carless young drivers and 32 young drivers with their own cars (as a comparison group) participated in this study. A modified Driver Behavior Questionnaire (DBQ) with a 4-factor structure (errors, violations, attention lapses, and memory lapses) was used to study carless young drivers' self-reported driving behaviors. A simulated driving experiment using a low-cost, fixed-base driving simulator was conducted to measure their simulated driving performance (errors, violations, attention lapses, driving maintenance, reaction time, and accidents). Self-reported DBQ outcomes showed that carless young drivers reported similar errors, more attention lapses, fewer memory lapses, and significantly fewer violation behaviors relative to young drivers with their own cars, whereas simulated driving results revealed that they committed significantly more errors, attention lapses, and violation behaviors than the comparison group. Carless young drivers had a lower ability to maintain the stability of speed and lane position, drove more cautiously approaching and passing through red traffic lights, and committed more accidents during simulated driving. A tendency to speed was not found among carless young drivers; their average speed and speeding frequency were all much lower than that of the comparison group. Lifetime mileage was the only significant predictor of carless young drivers' self-reported violations, simulated violations

In Patients with Cirrhosis, Driving Simulator Performance is Associated With Real-life Driving

DEFF Research Database (Denmark)

Lauridsen, Mette Enok Munk; Thacker, Leroy R; White, Melanie B

2016-01-01

BACKGROUND & AIMS: Minimal hepatic encephalopathy (MHE) has been linked to higher real-life rates of automobile crashes and poor performance in driving simulation studies, but the link between driving simulator performance and real-life automobile crashes has not been clearly established. Further......, not all patients with MHE are unsafe drivers, but it is unclear how to distinguish them from unsafe drivers. We investigated the link between performance on driving simulators and real-life automobile accidents and traffic violations. We also aimed to identify features of unsafe drivers with cirrhosis...... and evaluated changes in simulated driving skills and MHE status after 1 year. METHODS: We performed a study of outpatients with cirrhosis (n=205; median 55 years old; median model for end-stage liver disease score, 9.5; none with overt hepatic encephalopathy or alcohol or illicit drug use within previous 6...

Coordinated control of electrical drives

International Nuclear Information System (INIS)

Keresztely, S.

1983-01-01

The control system developed for the fuel handling machine of nuclear power plants contains seven microcomputers. Redundant hardware and software structure ensures high reliability and availability. The sensors are doubled and each set is connected to its own microcomputer for evaluation of measurements. The control program, coordinating seven electrical drives, is run on two identical microcomputers, and has access to both sets of measurement results. Two control desks are provided. The seventh microcomputer generates the digital picture of the working site around the actual position and the picture is sent to color TV monitors at the control desks. System reliability: failure of any part of the system causes an error message and no action. System availability: for emergency purposes, one of every pair of the identical subsystems must be operational. In this emergency mode unconditional reliability is lost. (author)

Starting the aircraft engines and gas-turbine drive by means of electric starter

Directory of Open Access Journals (Sweden)

І.М. Іщенко

2004-04-01

Full Text Available  In the article the questions of the starting the aircraft engines and gas-turbine drive by means of electric starter is considered. In the same way in the article are determined the main requirements to steady-state converter for feeding electric starter.

Evaluation of semiconductor devices for Electric and Hybrid Vehicle (EHV) ac-drive applications, volume 1

Science.gov (United States)

Lee, F. C.; Chen, D. Y.; Jovanovic, M.; Hopkins, D. C.

1985-01-01

The results of evaluation of power semiconductor devices for electric hybrid vehicle ac drive applications are summarized. Three types of power devices are evaluated in the effort: high power bipolar or Darlington transistors, power MOSFETs, and asymmetric silicon control rectifiers (ASCR). The Bipolar transistors, including discrete device and Darlington devices, range from 100 A to 400 A and from 400 V to 900 V. These devices are currently used as key switching elements inverters for ac motor drive applications. Power MOSFETs, on the other hand, are much smaller in current rating. For the 400 V device, the current rating is limited to 25 A. For the main drive of an electric vehicle, device paralleling is normally needed to achieve practical power level. For other electric vehicle (EV) related applications such as battery charger circuit, however, MOSFET is advantageous to other devices because of drive circuit simplicity and high frequency capability. Asymmetrical SCR is basically a SCR device and needs commutation circuit for turn off. However, the device poses several advantages, i.e., low conduction drop and low cost.

Influences on dispatch of power generation when introducing electric drive vehicles in an Irish power system year 2020

DEFF Research Database (Denmark)

Juul, Nina; Mullane, Alan; Meibom, Peter

plants. For the future transport system, electric drive vehicles are expected to be one of the solutions. Introducing different electric drive vehicle penetrations in a power system with a large amount of wind power, changes the usage of the predefined power system. This work presents investigations......Increased focus on global warming and CO2 emissions imply increased focus on the energy system, consisting of the heat, power, and transport systems. Solutions for the heat and power system are increasing penetrations of renewable heat and power generation plants such as wind power and biomass heat...... of different charging regimes’ influence of the power dispatch in the Irish power system. Analyses show an overall cost decrease and CO2 emission increase in the heat and power system with the introduction of electric drive vehicles. Furthermore, increased intelligence in the electric drive vehicle charging...

Performance and energy management of a novel full hybrid electric powertrain system

International Nuclear Information System (INIS)

Chung, Cheng-Ta; Hung, Yi-Hsuan

2015-01-01

This study compared the performance and energy management between a novel full hybrid electric powertrain and a traditional power-split hybrid system. The developed planetary gearset and dual clutch configuration provides five operation modes. Equations for the torque and speed of power sources for the planetary gearset and dual clutch system and the Toyota Hybrid System are firstly derived. By giving vehicle performance of gradability, maximal speeds in hybrid and pure electric modes, the power sources of the 210 kg target vehicle are: a 125 cc engine and two 1.8 kW motor and generator. The optimal tank-to-wheel efficiencies, ratios of circulating power, and operation points at specific vehicle speeds and out loads are calculated. Simulation results show that the dual-motor electric vehicle mode offers superior performance regarding electric drive; the low capacity of the battery is conducive to reducing manufacturing and maintenance costs; the tank-to-wheel efficiency is mainly operated above 20% while the power split electronic-continuously-variable-transmission mode is the major operation mode, and a maximum of 17% fuel economy improvement is achieved compared with the Toyota Hybrid System in most of the vehicle speed ranges. The outstanding performance warrants further real-system development, especially regarding the implementation in plug-in and sport hybrid powertrain designs. - Highlights: • An innovative power split hybrid powertrain was designed. • Dual-motor electric-vehicle mode highlighted for plug-in function. • Power circulation ratios and five driving modes were analyzed. • Global search method utilized for optimal energy management. • Maximal 17+% fuel improvement compared to Toyota Hybrid System

Particle swarm optimization of driving torque demand decision based on fuel economy for plug-in hybrid electric vehicle

International Nuclear Information System (INIS)

Shen, Peihong; Zhao, Zhiguo; Zhan, Xiaowen; Li, Jingwei

2017-01-01

In this paper, an energy management strategy based on logic threshold is proposed for a plug-in hybrid electric vehicle. The plug-in hybrid electric vehicle powertrain model is established using MATLAB/Simulink based on experimental tests of the power components, which is validated by the comparison with the verified simulation model which is built in the AVL Cruise. The influence of the driving torque demand decision on the fuel economy of plug-in hybrid electric vehicle is studied using a simulation. The optimization method for the driving torque demand decision, which refers to the relationship between the accelerator pedal opening and driving torque demand, from the perspective of fuel economy is formulated. The dynamically changing inertia weight particle swarm optimization is used to optimize the decision parameters. The simulation results show that the optimized driving torque demand decision can improve the PHEV fuel economy by 15.8% and 14.5% in the fuel economy test driving cycle of new European driving cycle and worldwide harmonized light vehicles test respectively, using the same rule-based energy management strategy. The proposed optimization method provides a theoretical guide for calibrating the parameters of driving torque demand decision to improve the fuel economy of the real plug-in hybrid electric vehicle. - Highlights: • The influence of the driving torque demand decision on the fuel economy is studied. • The optimization method for the driving torque demand decision is formulated. • An improved particle swarm optimization is utilized to optimize the parameters. • Fuel economy is improved by using the optimized driving torque demand decision.

A New Approach in Teaching Power Electronics Control of Electrical Drives using Real-Time

DEFF Research Database (Denmark)

Teodorescu, Remus; Bech, Michael Møller; Blaabjerg, Frede

2000-01-01

A new approach in teaching power electronics and electrical drives is achieved at the Flexible Drives System Laboratory (FDSL) from Aalborg University by using the new Total Development Environment (TDE) concept that allows a full visual block-oriented programming of dynamic real-time systems...

ALCOHOL AND DISTRACTION INTERACT TO IMPAIR DRIVING PERFORMANCE

Science.gov (United States)

Harrison, Emily L. R.; Fillmore, Mark T.

2011-01-01

Background Recognition of the risks associated with alcohol intoxication and driver distraction has led to a wealth of simulated driving research aimed at studying the adverse effects of each of these factors. Research on driving has moved beyond the individual, separate examination of these factors to the examination of potential interactions between alcohol intoxication and driver distraction. In many driving situations, distractions are commonplace and might have little or no disruptive influence on primary driving functions. Yet, such distractions might become disruptive to a driver who is intoxicated. Methods The present study examined the interactive impairing effects of alcohol intoxication and driver distraction on simulated driving performance in 40 young adult drivers using a divided attention task as a distracter activity. The interactive influence of alcohol and distraction was tested by having drivers perform the driving task under four different conditions: 0.65 g/kg alcohol; 0.65 g/kg alcohol + divided attention; placebo; and placebo + divided attention. Results As hypothesized, divided attention had no impairing effect on driving performance in sober drivers. However, under alcohol, divided attention exacerbated the impairing effects of alcohol on driving precision. Conclusions Alcohol and distraction continue to be appropriate targets for research into ways to reduce the rates of driving-related fatalities and injuries. Greater consideration of how alcohol and distraction interact to impair aspects of driving performance can further efforts to create prevention and intervention measures to protect drivers, particularly young adults. PMID:21277119

Alcohol and distraction interact to impair driving performance.

Science.gov (United States)

Harrison, Emily L R; Fillmore, Mark T

2011-08-01

Recognition of the risks associated with alcohol intoxication and driver distraction has led to a wealth of simulated driving research aimed at studying the adverse effects of each of these factors. Research on driving has moved beyond the individual, separate examination of these factors to the examination of potential interactions between alcohol intoxication and driver distraction. In many driving situations, distractions are commonplace and might have little or no disruptive influence on primary driving functions. Yet, such distractions might become disruptive to a driver who is intoxicated. The present study examined the interactive impairing effects of alcohol intoxication and driver distraction on simulated driving performance in 40 young adult drivers using a divided attention task as a distracter activity. The interactive influence of alcohol and distraction was tested by having drivers perform the driving task under four different conditions: 0.65 g/kg alcohol; 0.65 g/kg alcohol+divided attention; placebo; and placebo+divided attention. As hypothesized, divided attention had no impairing effect on driving performance in sober drivers. However, under alcohol, divided attention exacerbated the impairing effects of alcohol on driving precision. Alcohol and distraction continue to be appropriate targets for research into ways to reduce the rates of driving-related fatalities and injuries. Greater consideration of how alcohol and distraction interact to impair aspects of driving performance can further efforts to create prevention and intervention measures to protect drivers, particularly young adults. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Effect of chronic nonmalignant pain on highway driving performance.

Science.gov (United States)

Veldhuijzen, D S; van Wijck, A J M; Wille, F; Verster, J C; Kenemans, J L; Kalkman, C J; Olivier, B; Volkerts, E R

2006-05-01

Most pain patients are treated in an outpatient setting and are engaged in daily activities including driving. Since several studies showed that cognitive functioning may be impaired in chronic nonmalignant pain, the question arises whether or not chronic nonmalignant pain affects driving performance. Therefore, the objective of the present study was to determine the effects of chronic nonmalignant pain on actual highway driving performance during normal traffic. Fourteen patients with chronic nonmalignant pain and 14 healthy controls, matched on age, educational level, and driving experience, participated in the study. Participants performed a standardized on-the-road driving test during normal traffic, on a primary highway. The primary parameter of the driving test is the Standard Deviation of Lateral Position (SDLP). In addition, driving-related skills (tracking, divided attention, and memory) were examined in the laboratory. Subjective assessments, such as pain intensity, and subjective driving quality, were rated on visual analogue scales. The results demonstrated that a subset of chronic nonmalignant pain patients had SDLPs that were higher than the matched healthy controls, indicating worse highway driving performance. Overall, there was a statistically significant difference in highway driving performance between the groups. Further, chronic nonmalignant pain patients rated their subjective driving quality to be normal, although their ratings were significantly lower than those of the healthy controls. No significant effects were found on the laboratory tests.

Predicting psychopharmacological drug effects on actual driving performance (SDLP) from psychometric tests measuring driving-related skills

OpenAIRE

Verster, Joris C.; Roth, Thomas

2011-01-01

Rationale There are various methods to examine driving ability. Comparisons between these methods and their relationship with actual on-road driving is often not determined. Objective The objective of this study was to determine whether laboratory tests measuring driving-related skills could adequately predict on-the-road driving performance during normal traffic. Methods Ninety-six healthy volunteers performed a standardized on-the-road driving test. Subjects were instructed to drive with a ...

Commercial Truck Driver Health and Safety: Exploring Distracted Driving Performance and Self-Reported Driving Skill.

Science.gov (United States)

Stavrinos, Despina; Heaton, Karen; Welburn, Sharon C; McManus, Benjamin; Griffin, Russell; Fine, Philip R

2016-08-01

Reducing distracters detrimental to commercial truck driving is a critical component of improving the safety performance of commercial drivers, and makes the highways safer for all drivers. This study used a driving simulator to examine effects of cell phone, texting, and email distractions as well as self-reported driver optimism bias on the driving performance of commercial truck drivers. Results revealed that more visually demanding tasks were related to poorer driving performance. However, the cell phone task resulted in less off-the-road eye glances. Drivers reporting being "very skilled" displayed poorer driving performance than those reporting being "skilled." Onboard communication devices provide a practical, yet visually and manually demanding, solution for connecting drivers and dispatchers. Trucking company policies should minimize interaction between dispatchers and drivers when the truck is in motion. Training facilities should integrate driving simulators into the instruction of commercial drivers, targeting over-confident drivers. © 2016 The Author(s).

THE EFFECT OF CELLULAR PHONE USE ON DRIVING PERFORMANCE

OpenAIRE

Toshiro ISHIDA

2001-01-01

Many experiments using driving simulators or real roads have shown that using a cellular phone while driving may cause an accident because it delays visual information processing by the driver. In this research, we examined the influence on driving performance of cellular phone use on a course that simulated streets. Driving conditions were driving only, listening to the car radio, hands-free cellular phone use and using a cellular phone with the left hand. Driving performance measurements in...

Climate Control Load Reduction Strategies for Electric Drive Vehicles in Warm Weather

Energy Technology Data Exchange (ETDEWEB)

Jeffers, M. A.; Chaney, L.; Rugh, J. P.

2015-04-30

Passenger compartment climate control is one of the largest auxiliary loads on a vehicle. Like conventional vehicles, electric vehicles (EVs) require climate control to maintain occupant comfort and safety, but cabin heating and air conditioning have a negative impact on driving range for all electric vehicles. Range reduction caused by climate control and other factors is a barrier to widespread adoption of EVs. Reducing the thermal loads on the climate control system will extend driving range, thereby reducing consumer range anxiety and increasing the market penetration of EVs. Researchers at the National Renewable Energy Laboratory have investigated strategies for vehicle climate control load reduction, with special attention toward EVs. Outdoor vehicle thermal testing was conducted on two 2012 Ford Focus Electric vehicles to evaluate thermal management strategies for warm weather, including solar load reduction and cabin pre-ventilation. An advanced thermal test manikin was used to assess a zonal approach to climate control. In addition, vehicle thermal analysis was used to support testing by exploring thermal load reduction strategies, evaluating occupant thermal comfort, and calculating EV range impacts. Through stationary cooling tests and vehicle simulations, a zonal cooling configuration demonstrated range improvement of 6%-15%, depending on the drive cycle. A combined cooling configuration that incorporated thermal load reduction and zonal cooling strategies showed up to 33% improvement in EV range.

Mercedes-Benz’s lancering af B-class Electric Drive på det danske marked: Mercedes-Benz release of B-Class Electric Drive on the Danish Mar-ket.

OpenAIRE

Nygaard, Rasmus; Steffen, Emil Saaby; Johansen, Ulrik Vingaard; Nielsson, Emil Bak; Kristoffersen, Christian Engelbrecht

2014-01-01

Abstract This thesis analyzes the challenges of Mercedes-Benz’s initiative to introduce the B-Class Electric Drive to the Danish market. Specifically, it identifies and suggests how Mercedes-Benz can overcome these challenges on a strategic level. One of the biggest areas of concern and challenge in the electric vehicle market, is the lack of confidence in the existing technology. Specifically, the concern surrounds the cars dependence on recharging stations, recharging time and the connectio...

Driving with the wandering mind: the effect that mind-wandering has on driving performance.

Science.gov (United States)

Yanko, Matthew R; Spalek, Thomas M

2014-03-01

The principal objective of the present work was to examine the effects of mind state (mind-wandering vs. on-task) on driving performance in a high-fidelity driving simulator. Mind-wandering is thought to interfere with goal-directed thought. It is likely, then, that when driving, mind-wandering might lead to impairments in critical aspects of driving performance. In two experiments, we assess the extent to which mind-wandering interferes with responsiveness to sudden events, mean velocity, and headway distance. Using a car-following procedure in a high-fidelity driving simulator, participants were probed at random times to indicate whether they were on-task at that moment or mind-wandering. The dependent measures were analyzed based on the participant's response to the probe. Compared to when on-task, when mind-wandering participants showed longer response times to sudden events, drove at a higher velocity, and maintained a shorter headway distance. Collectively, these findings indicate that mind-wandering affects a broad range of driving responses and may therefore lead to higher crash risk. The results suggest that situations that are likely associated with mind-wandering (e.g., route familiarity) can impair driving performance.

Thermal modelling of Li-ion polymer battery for electric vehicle drive cycles

Science.gov (United States)

Chacko, Salvio; Chung, Yongmann M.

2012-09-01

Time-dependent, thermal behaviour of a lithium-ion (Li-ion) polymer cell has been modelled for electric vehicle (EV) drive cycles with a view to developing an effective battery thermal management system. The fully coupled, three-dimensional transient electro-thermal model has been implemented based on a finite volume method. To support the numerical study, a high energy density Li-ion polymer pouch cell was tested in a climatic chamber for electric load cycles consisting of various charge and discharge rates, and a good agreement was found between the model predictions and the experimental data. The cell-level thermal behaviour under stressful conditions such as high power draw and high ambient temperature was predicted with the model. A significant temperature increase was observed in the stressful condition, corresponding to a repeated acceleration and deceleration, indicating that an effective battery thermal management system would be required to maintain the optimal cell performance and also to achieve a full battery lifesapn.

Artificial intelligence-based condition monitoring for practical electrical drives

OpenAIRE

Ashari, Djoni; Pislaru, Crinela; Ball, Andrew; Gu, Fengshou

2012-01-01

The main types of existing Condition Monitoring methods (MCSA, GA, IAS) for electrical drives are\\ud described. Then the steps for the design of expert systems are presented: problem identification and analysis, system specification, development tool selection, knowledge based, prototyping and testing. The employment of SOMA (Self-Organizing Migrating Algorithm) used for the optimization of ambient\\ud vibration energy harvesting is analyzed. The power electronics devices are becoming smaller ...

Effects of chewing gum on driving performance as evaluated by the STISIM driving simulator.

Science.gov (United States)

Yoo, Ingyu; Kim, Eun-Joo; Lee, Joo-Hyun

2015-06-01

[Purpose] The purpose of this study was to determine the effects of chewing gum on driving performance in a driving simulator. [Subjects] In total, 26 young licensed drivers participated. [Methods] The driving scenario was typical of an urban environment: a single-carriageway, two-way road consisting of a mix of curved and straight sections, with considerable levels of traffic, pedestrians, and parked cars. Mean distance driven above the speed limit, lane position, mean distance driven across the center line, and mean distance driven off the road were used as estimates of brake, accelerator, and steering control. The results were compared with those of a non-chewing gum control condition. [Results] The driving performance while chewing gum was significantly better: the mean distance driven above the speed limit was 26.61% shorter, and the mean distance driven off the road was 31.99% shorter. Lane position and mean distance driven across the center line did not differ significantly between the two conditions. [Conclusion] Chewing gum appears to enhance driving performance during a sustained attention driving task.

Energy efficiency improvements in electric motors and drives

Energy Technology Data Exchange (ETDEWEB)

Bertoldi, P. [Commission of the European Communities, Brussels (Belgium). Directorate General for Energy; Ameida, A.T. de [Coimbra Univ. (Portugal). Dept. de Engenharia Electrotecnica; Falkner, H. [eds.] [AEA Technolgy, Harwell (United Kingdom). ETSU

2000-07-01

This book covers the state of the art of energy-efficient electric motor technologies, which can be used now and in the near future to achieve significant and cost-effective energy savings. Recent developments in advanced motor technologies by some of the largest manufacturers of motors and drives are also presented. Although energy-efficient motor technologies can save a huge amount of electricity, they still have not been widely adopted. The barriers which can hinder the adoption of those technologies are presented. Policies and programmes to promote the large scale penetration of energy-efficient technologies and the market transformation are featured in the book, describing the experiences carried out in different parts of the world. This extensive coverage includes contributions from relevant institutions in the European Union, North America, Latin America, Japan, Australia and New Zealand. (orig.)

Neurocognitive Correlates of Young Drivers' Performance in a Driving Simulator.

Science.gov (United States)

Guinosso, Stephanie A; Johnson, Sara B; Schultheis, Maria T; Graefe, Anna C; Bishai, David M

2016-04-01

Differences in neurocognitive functioning may contribute to driving performance among young drivers. However, few studies have examined this relation. This pilot study investigated whether common neurocognitive measures were associated with driving performance among young drivers in a driving simulator. Young drivers (19.8 years (standard deviation [SD] = 1.9; N = 74)) participated in a battery of neurocognitive assessments measuring general intellectual capacity (Full-Scale Intelligence Quotient, FSIQ) and executive functioning, including the Stroop Color-Word Test (cognitive inhibition), Wisconsin Card Sort Test-64 (cognitive flexibility), and Attention Network Task (alerting, orienting, and executive attention). Participants then drove in a simulated vehicle under two conditions-a baseline and driving challenge. During the driving challenge, participants completed a verbal working memory task to increase demand on executive attention. Multiple regression models were used to evaluate the relations between the neurocognitive measures and driving performance under the two conditions. FSIQ, cognitive inhibition, and alerting were associated with better driving performance at baseline. FSIQ and cognitive inhibition were also associated with better driving performance during the verbal challenge. Measures of cognitive flexibility, orienting, and conflict executive control were not associated with driving performance under either condition. FSIQ and, to some extent, measures of executive function are associated with driving performance in a driving simulator. Further research is needed to determine if executive function is associated with more advanced driving performance under conditions that demand greater cognitive load. Copyright © 2016 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

Does correcting astigmatism with toric lenses improve driving performance?

Science.gov (United States)

Cox, Daniel J; Banton, Thomas; Record, Steven; Grabman, Jesse H; Hawkins, Ronald J

2015-04-01

Driving is a vision-based activity of daily living that impacts safety. Because visual disruption can compromise driving safety, contact lens wearers with astigmatism may pose a driving safety risk if they experience residual blur from spherical lenses that do not correct their astigmatism or if they experience blur from toric lenses that rotate excessively. Given that toric lens stabilization systems are continually improving, this preliminary study tested the hypothesis that astigmats wearing toric contact lenses, compared with spherical lenses, would exhibit better overall driving performance and driving-specific visual abilities. A within-subject, single-blind, crossover, randomized design was used to evaluate driving performance in 11 young adults with astigmatism (-0.75 to -1.75 diopters cylinder). Each participant drove a highly immersive, virtual reality driving simulator (210 degrees field of view) with (1) no correction, (2) spherical contact lens correction (ACUVUE MOIST), and (3) toric contact lens correction (ACUVUE MOIST for Astigmatism). Tactical driving skills such as steering, speed management, and braking, as well as operational driving abilities such as visual acuity, contrast sensitivity, and foot and arm reaction time, were quantified. There was a main effect for type of correction on driving performance (p = 0.05). Correction with toric lenses resulted in significantly safer tactical driving performance than no correction (p driving safety from no correction (p = 0.118). Operational tests differentiated corrected from uncorrected performance for both spherical (p = 0.008) and toric (p = 0.011) lenses, but they were not sensitive enough to differentiate toric from spherical lens conditions. Given previous research showing that deficits in these tactical skills are predictive of future real-world collisions, these preliminary data suggest that correcting low to moderate astigmatism with toric lenses may be important to driving safety. Their

The use of an axial flux permanent magnet in-wheel direct drive in an electric bicycle

Energy Technology Data Exchange (ETDEWEB)

Johansen, P.R. [Norwegian University of Science and Technology, Trondheim (Norway). Dept. of Electrical Power Engineering; Patterson, D.; O' Keefe, C.; Swenson, J. [Northern Territory University, Darwin (Australia). NT Centre for Energy Research

2001-03-01

The research described in this paper concentrates on the development of an electronic converter. Successful completion of this converter provides the final component for the larger electric bicycle project. The controller developed for the bicycle is rated at 400 W and is hard-switched. It uses MOSFETs as power switching devices. There are three Hall effect sensors placed 120 electrical degrees apart from each other in the motor for velocity and position sensing. The torque generated by the machine is controlled by hysteresis band current control. In order for the motor/controller to be commercially viable, particular attention was paid to the costs of the controller. The result, an efficient yet cheap controller. Measurement of efficiency is difficult in high performance power electronic controllers (Patterson DJA very high efficiency controller for an axial flux permanent magnet wheel drive in a solar powered vehicle. 2nd IEEE International Conference on Power Electronics Drives and Energy Systems for Industrial Growth, IEEE PEDES '98, Perth, 30th November-3rd December, 1998). The paper includes discussion of a calorimetric method for measurement. (author)

The influence of music on mental effort and driving performance.

Science.gov (United States)

Ünal, Ayça Berfu; Steg, Linda; Epstude, Kai

2012-09-01

The current research examined the influence of loud music on driving performance, and whether mental effort mediated this effect. Participants (N=69) drove in a driving simulator either with or without listening to music. In order to test whether music would have similar effects on driving performance in different situations, we manipulated the simulated traffic environment such that the driving context consisted of both complex and monotonous driving situations. In addition, we systematically kept track of drivers' mental load by making the participants verbally report their mental effort at certain moments while driving. We found that listening to music increased mental effort while driving, irrespective of the driving situation being complex or monotonous, providing support to the general assumption that music can be a distracting auditory stimulus while driving. However, drivers who listened to music performed as well as the drivers who did not listen to music, indicating that music did not impair their driving performance. Importantly, the increases in mental effort while listening to music pointed out that drivers try to regulate their mental effort as a cognitive compensatory strategy to deal with task demands. Interestingly, we observed significant improvements in driving performance in two of the driving situations. It seems like mental effort might mediate the effect of music on driving performance in situations requiring sustained attention. Other process variables, such as arousal and boredom, should also be incorporated to study designs in order to reveal more on the nature of how music affects driving. Copyright © 2012 Elsevier Ltd. All rights reserved.

Integrated Fault Diagnosis Algorithm for Motor Sensors of In-Wheel Independent Drive Electric Vehicles

Science.gov (United States)

Jeon, Namju; Lee, Hyeongcheol

2016-01-01

An integrated fault-diagnosis algorithm for a motor sensor of in-wheel independent drive electric vehicles is presented. This paper proposes a method that integrates the high- and low-level fault diagnoses to improve the robustness and performance of the system. For the high-level fault diagnosis of vehicle dynamics, a planar two-track non-linear model is first selected, and the longitudinal and lateral forces are calculated. To ensure redundancy of the system, correlation between the sensor and residual in the vehicle dynamics is analyzed to detect and separate the fault of the drive motor system of each wheel. To diagnose the motor system for low-level faults, the state equation of an interior permanent magnet synchronous motor is developed, and a parity equation is used to diagnose the fault of the electric current and position sensors. The validity of the high-level fault-diagnosis algorithm is verified using Carsim and Matlab/Simulink co-simulation. The low-level fault diagnosis is verified through Matlab/Simulink simulation and experiments. Finally, according to the residuals of the high- and low-level fault diagnoses, fault-detection flags are defined. On the basis of this information, an integrated fault-diagnosis strategy is proposed. PMID:27973431

Integrated Fault Diagnosis Algorithm for Motor Sensors of In-Wheel Independent Drive Electric Vehicles.

Science.gov (United States)

Jeon, Namju; Lee, Hyeongcheol

2016-12-12

An integrated fault-diagnosis algorithm for a motor sensor of in-wheel independent drive electric vehicles is presented. This paper proposes a method that integrates the high- and low-level fault diagnoses to improve the robustness and performance of the system. For the high-level fault diagnosis of vehicle dynamics, a planar two-track non-linear model is first selected, and the longitudinal and lateral forces are calculated. To ensure redundancy of the system, correlation between the sensor and residual in the vehicle dynamics is analyzed to detect and separate the fault of the drive motor system of each wheel. To diagnose the motor system for low-level faults, the state equation of an interior permanent magnet synchronous motor is developed, and a parity equation is used to diagnose the fault of the electric current and position sensors. The validity of the high-level fault-diagnosis algorithm is verified using Carsim and Matlab/Simulink co-simulation. The low-level fault diagnosis is verified through Matlab/Simulink simulation and experiments. Finally, according to the residuals of the high- and low-level fault diagnoses, fault-detection flags are defined. On the basis of this information, an integrated fault-diagnosis strategy is proposed.

Effect of hybrid system battery performance on determining CO2 emissions of hybrid electric vehicles in real-world conditions

International Nuclear Information System (INIS)

Alvarez, Robert; Schlienger, Peter; Weilenmann, Martin

2010-01-01

Hybrid electric vehicles (HEVs) can potentially reduce vehicle CO 2 emissions by using recuperated kinetic vehicle energy stored as electric energy in a hybrid system battery (HSB). HSB performance affects the individual net HEV CO 2 emissions for a given driving pattern, which is considered to be equivalent to unchanged net energy content in the HSB. The present study investigates the influence of HSB performance on the statutory correction procedure used to determine HEV CO 2 emissions in Europe based on chassis dynamometer measurements with three identical in-use examples of a full HEV model featuring different mileages. Statutory and real-world driving cycles and full electric vehicle operation modes have been considered. The main observation is that the selected HEVs can only use 67-80% of the charge provided to the HSB, which distorts the outcomes of the statutory correction procedure that does not consider such irreversibility. CO 2 emissions corrected according to this procedure underestimate the true net CO 2 emissions of one HEV by approximately 13% in real-world urban driving. The correct CO 2 emissions are only reproduced when considering the HSB performance in this driving pattern. The statutory procedure for correcting HEV CO 2 emissions should, therefore, be adapted.

Electric Vehicle - Economical driving

DEFF Research Database (Denmark)

Jensen, VCE, Steen V.; Schøn, Henriette

1999-01-01

Instruct the reader in getting most satisfaction out of an EV, especially concerning driving and loading.......Instruct the reader in getting most satisfaction out of an EV, especially concerning driving and loading....

Analyzing driving forces behind changes in energy vulnerability of Spanish electricity generation through a Divisia index-based method

International Nuclear Information System (INIS)

Fernández González, P.; Moreno, B.

2015-01-01

Highlights: • We propose and develop the LMDI approach to factorize changes in electricity bill vulnerability. • Spanish vulnerability (1995–2011) markedly grew mainly by increasing gas dependence. • Fuel price increase and growing importance of electricity damage energy security. • Energy intensity advances & fuel diversification: insufficient to drive vulnerability. • Main recommendation: enhance internal energy market and common external EU strategy. - Abstract: High energy dependence on fossil raises vulnerability concerns about security of supply and energy cost. This research examines the impact of high dependence of imported fuels for power generation in Spain through the quantification and analysis of the driving forces behind the change in its electricity bill. Following logarithmic mean Divisia indexes approach, we present and perform a new method that enables a complete decomposition of changes in electricity vulnerability into contributions from several drivers. In fact, we identify five predefined factors behind the variations in vulnerability in Spain during the 1998–2011 period: fuel price, average heat rate, fuel dependence, degree of electricity importance and energy intensity. The application of this approach reveals a significant increase in Spanish vulnerability in the last two decades, promoted by increments in fuel price and importance of electricity over the primary energy consumption, but especially by increasing fuel dependence (particularly gas dependence). Therefore, findings mainly advocate for those strategies aimed at reducing Spanish energy dependence. Also those improving thermal efficiency and energy intensity are indicated

Degree of Fault Tolerance as a Comprehensive Parameter for Reliability Evaluation of Fault Tolerant Electric Traction Drives

Directory of Open Access Journals (Sweden)

Igor Bolvashenkov

2016-09-01

Full Text Available This paper describes a new approach and methodology of quantitative assessment of the fault tolerance of electric power drive consisting of the multi-phase traction electric motor and multilevel electric inverter. It is suggested to consider such traction drive as a system with several degraded states. As a comprehensive parameter for evaluating of the fault tolerance, it is proposed to use the criterion of degree of the fault tolerance. For the approbation of the proposed method, the authors carried out research and obtained results of its practical application for evaluating the fault tolerance of the power train of an electrical helicopter.

Research on the Multi-Energy Management Strategy of the Electric Drive System of a Tracked Bulldozer

Directory of Open Access Journals (Sweden)

Ming Pan

2016-01-01

Full Text Available The multi-energy management strategy of electric drive system of tracked bulldozer was researched. Firstly, based on power requirement of typical working condition of a tracked bulldozer, the power distribution strategy for three energy sources in the front power chain was proposed by using wavelet theory and fuzzy control theory. Secondly, the electric drive system simulation platform was built in MATLAB/Simulink. At last, a driver-controller based HILS (hardware-in-the-loop simulation platform was built and the multi-energy management strategy was verified. The HILS result shows that front power chain’s power output can meet the back power chain’s requirement, the engine-generator set works near the best fuel consumption curve, and the battery pack’s charge-discharge frequency and current are low. Thus the designed multi-energy management strategy can be used in real-time control of electric drive bulldozer.

Overview of the Safety Issues Associated with the Compressed Natural Gas Fuel System and Electric Drive System in a Heavy Hybrid Electric Vehicle

Energy Technology Data Exchange (ETDEWEB)

Nelson, S.C.

2002-11-14

This report evaluates the hazards that are unique to a compressed-natural-gas (CNG)-fueled heavy hybrid electric vehicle (HEV) design compared with a conventional heavy vehicle. The unique design features of the heavy HEV are the CNG fuel system for the internal-combustion engine (ICE) and the electric drive system. This report addresses safety issues with the CNG fuel system and the electric drive system. Vehicles on U. S. highways have been propelled by ICEs for several decades. Heavy-duty vehicles have typically been fueled by diesel fuel, and light-duty vehicles have been fueled by gasoline. The hazards and risks posed by ICE vehicles are well understood and have been generally accepted by the public. The economy, durability, and safety of ICE vehicles have established a standard for other types of vehicles. Heavy-duty (i.e., heavy) HEVs have recently been introduced to U. S. roadways, and the hazards posed by these heavy HEVs can be compared with the hazards posed by ICE vehicles. The benefits of heavy HEV technology are based on their potential for reduced fuel consumption and lower exhaust emissions, while the disadvantages are the higher acquisition cost and the expected higher maintenance costs (i.e., battery packs). The heavy HEV is more suited for an urban drive cycle with stop-and-go driving conditions than for steady expressway speeds. With increasing highway congestion and the resulting increased idle time, the fuel consumption advantage for heavy HEVs (compared with conventional heavy vehicles) is enhanced by the HEVs' ability to shut down. Any increase in fuel cost obviously improves the economics of a heavy HEV. The propulsion system for a heavy HEV is more complex than the propulsion system for a conventional heavy vehicle. The heavy HEV evaluated in this study has in effect two propulsion systems: an ICE fueled by CNG and an electric drive system with additional complexity and failure modes. This additional equipment will result in a less

Event-related potentials and secondary task performance during simulated driving.

Science.gov (United States)

Wester, A E; Böcker, K B E; Volkerts, E R; Verster, J C; Kenemans, J L

2008-01-01

Inattention and distraction account for a substantial number of traffic accidents. Therefore, we examined the impact of secondary task performance (an auditory oddball task) on a primary driving task (lane keeping). Twenty healthy participants performed two 20-min tests in the Divided Attention Steering Simulator (DASS). The visual secondary task of the DASS was replaced by an auditory oddball task to allow recording of brain activity. The driving task and the secondary (distracting) oddball task were presented in isolation and simultaneously, to assess their mutual interference. In addition to performance measures (lane keeping in the primary driving task and reaction speed in the secondary oddball task), brain activity, i.e. event-related potentials (ERPs), was recorded. Performance parameters on the driving test and the secondary oddball task did not differ between performance in isolation and simultaneous performance. However, when both tasks were performed simultaneously, reaction time variability increased in the secondary oddball task. Analysis of brain activity indicated that ERP amplitude (P3a amplitude) related to the secondary task, was significantly reduced when the task was performed simultaneously with the driving test. This study shows that when performing a simple secondary task during driving, performance of the driving task and this secondary task are both unaffected. However, analysis of brain activity shows reduced cortical processing of irrelevant, potentially distracting stimuli from the secondary task during driving.

Study on the effect of driving cycles on energy efficiency of electric vehicles

Energy Technology Data Exchange (ETDEWEB)

Ji Fenzhu; Xu Licong [School of Transportation Science and Engineering of Beihang Univ., BJ (China); Wu Zhixin [Tianjin Qing Yuan Electric Vehicle Corp. Ltd., TJ (China)

2009-07-01

The energy usage efficiency of electric vehicles (EVS) and evaluation index of electromotor efficiency were studied. The idea of ''interval usage percentage of energy efficiency'' and ''exertion degree of energy efficiency'' of electromotor was brought forward. The effect of driving cycles on the distribution of running status of electromotor and its efficiency was investigated. The electromotor efficiency and the variety trend of average driving force at different driving cycles were discussed. Based on several typical domestic and foreign driving cycles, the exertion degree of energy efficiency and the whole efficiency of power train on some types of EVS were analyzed and calculated. The result indicates that there is a difference of 9.64% in exertion degree of energy efficiency of electromotor at different driving cycles. The efficiency distribution of electromotor and control system is different, and the average driving force is different, too. That cause the great variety in driving range. The idiographic reference data are provided to the establishment of driving cycles' criterion of EVS in our country. (orig.)

Driving and visuospatial performance in people with hemianopia

NARCIS (Netherlands)

Tant, M.L.; Brouwer, W.H.; Cornelissen, F.W; Kooijman, A.C

2002-01-01

Practical fitness to drive was studied in 28 patients with homonymous hemianopia (HH). More specifically, visual performance during driving and neuropsychological visuospatial test performance were compared and related. Visuospatial tests were a priori classified in four visuospatial sets, and were

New drive axles for hybrid applications in low-floor city busses. The electric axle AVE 130; Neue Antriebsachse fuer Hybridapplikationen in Niederflur-Stadtbussen. Die Elektroachse AVE 130

Energy Technology Data Exchange (ETDEWEB)

Solka, Ulrich [ZF Passau GmbH (Germany); Mueller, Axel M. [ZF Friedrichshafen AG (Germany)

2009-07-01

The contribution under consideration reports on the mechanically constructional structure of the electrically driven low-floor axle AVE 130 of ZF Friedrichshafen AG (Friedrichshafen, Federal Republic of Germany). The characteristics of the electric drive are presented with the particularities of the implemented asynchronous machine and the road performances which can be developed by a city bus using this axle. Also the system characteristics of a hybrid bus with serial hybrid drive system concerning to aggregate arrangement, mass balances and the interaction of the aggregates in the drive briefly are discussed. The results of numerical simulation regarding fuel saving potential in these systems round the remarks off.

Effects of Non-Driving Related Task Modalities on Takeover Performance in Highly Automated Driving.

Science.gov (United States)

Wandtner, Bernhard; Schömig, Nadja; Schmidt, Gerald

2018-04-01

Aim of the study was to evaluate the impact of different non-driving related tasks (NDR tasks) on takeover performance in highly automated driving. During highly automated driving, it is allowed to engage in NDR tasks temporarily. However, drivers must be able to take over control when reaching a system limit. There is evidence that the type of NDR task has an impact on takeover performance, but little is known about the specific task characteristics that account for performance decrements. Thirty participants drove in a simulator using a highly automated driving system. Each participant faced five critical takeover situations. Based on assumptions of Wickens's multiple resource theory, stimulus and response modalities of a prototypical NDR task were systematically manipulated. Additionally, in one experimental group, the task was locked out simultaneously with the takeover request. Task modalities had significant effects on several measures of takeover performance. A visual-manual texting task degraded performance the most, particularly when performed handheld. In contrast, takeover performance with an auditory-vocal task was comparable to a baseline without any task. Task lockout was associated with faster hands-on-wheel times but not altered brake response times. Results showed that NDR task modalities are relevant factors for takeover performance. An NDR task lockout was highly accepted by the drivers and showed moderate benefits for the first takeover reaction. Knowledge about the impact of NDR task characteristics is an enabler for adaptive takeover concepts. In addition, it might help regulators to make decisions on allowed NDR tasks during automated driving.

Influence of driving patterns on life cycle cost and emissions of hybrid and plug-in electric vehicle powertrains

International Nuclear Information System (INIS)

Karabasoglu, Orkun; Michalek, Jeremy

2013-01-01

We compare the potential of hybrid, extended-range plug-in hybrid, and battery electric vehicles to reduce lifetime cost and life cycle greenhouse gas emissions under various scenarios and simulated driving conditions. We find that driving conditions affect economic and environmental benefits of electrified vehicles substantially: Under the urban NYC driving cycle, hybrid and plug-in vehicles can cut life cycle emissions by 60% and reduce costs up to 20% relative to conventional vehicles (CVs). In contrast, under highway test conditions (HWFET) electrified vehicles offer marginal emissions reductions at higher costs. NYC conditions with frequent stops triple life cycle emissions and increase costs of conventional vehicles by 30%, while aggressive driving (US06) reduces the all-electric range of plug-in vehicles by up to 45% compared to milder test cycles (like HWFET). Vehicle window stickers, fuel economy standards, and life cycle studies using average lab-test vehicle efficiency estimates are therefore incomplete: (1) driver heterogeneity matters, and efforts to encourage adoption of hybrid and plug-in vehicles will have greater impact if targeted to urban drivers vs. highway drivers; and (2) electrified vehicles perform better on some drive cycles than others, so non-representative tests can bias consumer perception and regulation of alternative technologies. We discuss policy implications. - Highlights: • Electrified vehicle life cycle emissions and cost depend on driving conditions. • GHGs can triple in NYC conditions vs. highway (HWFET), cost +30%. • Under NYC conditions hybrid and plug-in vehicles cut GHGs up to 60%, cost 20%. • Under HWFET conditions they offer few GHG reductions at higher costs. • Federal tests for window labels and CAFE standards favor some technologies over others

Experimental analysis on the performance of lithium based batteries for road full electric and hybrid vehicles

International Nuclear Information System (INIS)

Capasso, Clemente; Veneri, Ottorino

2014-01-01

Highlights: • Performance analysis for lithium storage technologies, such as Li[NiCoMn]O 2 and LiFePO 4 batteries. • Actual capacity of lithium technologies analyzed almost close to their nominal capacity also for high discharging current. • The charging efficiency for Li[NiCoMn]O 2 positively affects the regenerative breaking and fast recharging operations. • The analyzed battery packs follow dynamic power requirements on performed road driving cycles. • Experimental results demonstrate driving range is much higher when battery packs are based on lithium technology. - Abstract: This paper deals with an experimental evaluation regarding the real performance of lithium based energy storage systems for automotive applications. In particular real working operations of different lithium based storage system technologies, such as Li[NiCoMn]O 2 and LiFePO 4 batteries, are compared in this work from the point of view of their application in supplying full electric and hybrid vehicles, taking as a reference the well-known behavior of lead acid batteries. For this purpose, the experimental tests carried out in laboratory are firstly performed on single storage modules in stationary conditions. In this case the related results are obtained by means of a bidirectional cycle tester based on the IGBT technology, and consent to evaluate, compare and contrast charge/discharge characteristics and efficiency at constant values of current/voltage/power for each storage technology analyzed. Then, lithium battery packs are tested in supplying a 1.8 kW electric power train using a laboratory test bench, based on a 48 V DC bus and specifically configured to simulate working operations of electric vehicles on the road. For this other experimentation the test bench is equipped with an electric brake and acquisition/control system, able to represent in laboratory the real vehicle conditions and road characteristics on predefined driving cycles at different slopes. The obtained

Oak Ridge National Laboratory Annual Progress Report for the Electric Drive Technologies Program

Energy Technology Data Exchange (ETDEWEB)

Ozpineci, Burak [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-10-01

The US Department of Energy (DOE) announced in May 2011 a new cooperative research effort comprising DOE, the US Council for Automotive Research (composed of automakers Ford Motor Company, General Motors Company, and Chrysler Group), Tesla Motors, and representatives of the electric utility and petroleum industries. Known as U.S. DRIVE (Driving Research and Innovation for Vehicle efficiency and Energy sustainability), it represents DOE’s commitment to developing public–private partnerships to fund high-risk–high-reward research into advanced automotive technologies. The new partnership replaces and builds upon the partnership known as FreedomCAR (derived from “Freedom” and “Cooperative Automotive Research”) that ran from 2002 through 2010 and the Partnership for a New Generation of Vehicles initiative that ran from 1993 through 2001. Oak Ridge National Laboratory’s (ORNL’s) Electric Drive Technologies (EDT) subprogram within the DOE Vehicle Technologies Office (VTO) provides support and guidance for many cutting-edge automotive technologies now under development. Research is focused on developing revolutionary new power electronics (PE), electric motor (EM), and traction drive system (TDS) technologies that will leapfrog current on-the-road technologies, leading to lower cost and better efficiency in transforming battery energy to useful work. The research and development (R&D) is also aimed at achieving a greater understanding of and improvements in the way the various new components of tomorrow’s automobiles will function as a unified system to improve fuel efficiency through research in more efficient TDSs. In supporting the development of advanced vehicle propulsion systems, the EDT subprogram fosters the development of technologies that will significantly improve efficiency, costs, and fuel economy

Method of electric powertrain matching for battery-powered electric cars

Science.gov (United States)

Ning, Guobao; Xiong, Lu; Zhang, Lijun; Yu, Zhuoping

2013-05-01

The current match method of electric powertrain still makes use of longitudinal dynamics, which can't realize maximum capacity for on-board energy storage unit and can't reach lowest equivalent fuel consumption as well. Another match method focuses on improving available space considering reasonable layout of vehicle to enlarge rated energy capacity for on-board energy storage unit, which can keep the longitudinal dynamics performance almost unchanged but can't reach lowest fuel consumption. Considering the characteristics of driving motor, method of electric powertrain matching utilizing conventional longitudinal dynamics for driving system and cut-and-try method for energy storage system is proposed for passenger cars converted from traditional ones. Through combining the utilization of vehicle space which contributes to the on-board energy amount, vehicle longitudinal performance requirements, vehicle equivalent fuel consumption level, passive safety requirements and maximum driving range requirement together, a comprehensive optimal match method of electric powertrain for battery-powered electric vehicle is raised. In simulation, the vehicle model and match method is built in Matlab/simulink, and the Environmental Protection Agency (EPA) Urban Dynamometer Driving Schedule (UDDS) is chosen as a test condition. The simulation results show that 2.62% of regenerative energy and 2% of energy storage efficiency are increased relative to the traditional method. The research conclusions provide theoretical and practical solutions for electric powertrain matching for modern battery-powered electric vehicles especially for those converted from traditional ones, and further enhance dynamics of electric vehicles.

Effect of hybrid system battery performance on determining CO{sub 2} emissions of hybrid electric vehicles in real-world conditions

Energy Technology Data Exchange (ETDEWEB)

Alvarez, Robert; Schlienger, Peter; Weilenmann, Martin [Empa, Swiss Federal Laboratories for Materials Science and Technology, Laboratory for Internal Combustion Engines, Ueberlandstrasse 129, CH-8600 Duebendorf (Switzerland)

2010-11-15

Hybrid electric vehicles (HEVs) can potentially reduce vehicle CO{sub 2} emissions by using recuperated kinetic vehicle energy stored as electric energy in a hybrid system battery (HSB). HSB performance affects the individual net HEV CO{sub 2} emissions for a given driving pattern, which is considered to be equivalent to unchanged net energy content in the HSB. The present study investigates the influence of HSB performance on the statutory correction procedure used to determine HEV CO{sub 2} emissions in Europe based on chassis dynamometer measurements with three identical in-use examples of a full HEV model featuring different mileages. Statutory and real-world driving cycles and full electric vehicle operation modes have been considered. The main observation is that the selected HEVs can only use 67-80% of the charge provided to the HSB, which distorts the outcomes of the statutory correction procedure that does not consider such irreversibility. CO{sub 2} emissions corrected according to this procedure underestimate the true net CO{sub 2} emissions of one HEV by approximately 13% in real-world urban driving. The correct CO{sub 2} emissions are only reproduced when considering the HSB performance in this driving pattern. The statutory procedure for correcting HEV CO{sub 2} emissions should, therefore, be adapted. (author)

Active load current sharing in fuel cell and battery fed DC motor drive for electric vehicle application

International Nuclear Information System (INIS)

Pany, Premananda; Singh, R.K.; Tripathi, R.K.

2016-01-01

Highlights: • Load current sharing in FC and battery fed dc drive. • Active current sharing control using LabVIEW. • Detail hardware implementation. • Controller performance is verified through MATLAB simulation and experimental results. - Abstract: In order to reduce the stress on fuel cell based hybrid source fed electric drive system the controller design is made through active current sharing (ACS) technique. The effectiveness of the proposed ACS technique is tested on a dc drive system fed from fuel cell and battery energy sources which enables both load current sharing and source power management. High efficiency and reliability of the hybrid system can be achieved by proper energy conversion and management of power to meet the load demand in terms of required voltage and current. To overcome the slow dynamics feature of FC, a battery bank of adequate power capacity has to be incorporated as FC voltage drops heavily during fast load demand. The controller allows fuel cell to operate in normal load region and draw the excess power from battery. In order to demonstrate the performance of the drive using ACS control strategy different modes of operation of the hybrid source with the static and dynamic behavior of the control system is verified through simulation and experimental results. This control scheme is implemented digitally in LabVIEW with PCI 6251 DAQ I/O interface card. The efficacy of the controller performance is demonstrated in system changing condition supplemented by experimental validation.

What drives people's opinions of electricity infrastructure? Empirical evidence from Ireland

International Nuclear Information System (INIS)

Bertsch, Valentin; Hyland, Marie; Mahony, Michael

2017-01-01

Across the EU, significant infrastructure investment is needed in both generation from renewable energy sources (RES) and the electricity grid to meet the European targets on emission reduction and RES expansion. Experiences show, however, that citizens may object to new energy infrastructure in their localities which may cause delays in achieving the targets. To avoid delays, it is crucial to understand what drives people's opinions. To explore people's opinions of different electricity generation and transmission technologies in Ireland, we conducted a nationally-representative survey. Concerning the drivers, we distinguish between socio-demographics, technology-specific perceptions, and energy policy preferences. Our results show that people generally have positive views of RES technologies. While this indicates that Irish citizens agree to move towards cleaner electricity sources, we find reluctance amongst people to have these technologies located close to their places of residence. We find that, across most technologies, the tradeoff people make between economic and environmental policy objectives drives their opinions of, and their tendencies to oppose, technology developments. The significance of most socio-demographic variables, however, is largely technology-dependent. This highlights that policy makers need to understand how people make tradeoffs between policy objectives and how these tradeoffs relate to their opinions of different technologies. - Highlights: • Conducted a survey to understand drivers of opinions of electricity infrastructure. • Considered socio-demographic, policy-related and technology-specific drivers. • Irish citizens generally have positive opinions of renewable technologies. • Positive opinions don't rule out local opposition. • Tradeoffs on policy objectives shape opinions most consistently across technologies.

Electric Vehicle - Economical driving

DEFF Research Database (Denmark)

Jensen, VCE, Steen V.; Schøn, Henriette

1999-01-01

How do you reduce the energy-wast when driving and loading EV's - or rather: How do I get more km/l out of an EV......How do you reduce the energy-wast when driving and loading EV's - or rather: How do I get more km/l out of an EV...

A multimodal assessment of driving performance in HIV infection.

Science.gov (United States)

Marcotte, T D; Wolfson, T; Rosenthal, T J; Heaton, R K; Gonzalez, R; Ellis, R J; Grant, I

2004-10-26

To examine if HIV-seropositive (HIV+) individuals are at risk for impaired driving. Sixty licensed drivers (40 HIV+, 20 HIV-) completed a neuropsychological (NP) test battery and driving assessments. Eleven HIV+ subjects were NP-impaired. Driving-related skills were assessed using 1) two driving simulations (examining accident avoidance and navigational abilities), 2) the Useful Field of View (UFOV) test, and 3) an on-road evaluation. HIV+ NP-impaired subjects had greater difficulty than cognitively intact subjects on all driving measures, whereas the HIV- and HIV+ NP-normal groups performed similarly. On the UFOV, the HIV+ NP-impaired group had worse performance on Visual Processing and Divided Attention tasks but not in overall risk classification. They also had a higher number of simulator accidents (1.3 vs 2.0; p = 0.03), were less efficient at completing the navigation task (3.2 vs 9.2 blocks; p = 0.001), and were more likely to fail the on-road evaluation (6 vs 36%; p = 0.02). Impairment in Executive Functioning was the strongest NP predictor of failing the on-road drive test. NP performance and both simulations independently contributed to a model predicting 48% of the variance in on-road performance. HIV+ NP-impaired individuals are at increased risk for on-road driving impairments, whereas HIV+ individuals with normal cognition are not at a significantly higher risk than HIV- subjects. Executive Functioning is most strongly associated with impaired on-road performance. Cognitive and simulator testing may each provide data in identifying driving-impaired individuals.

Electric drive choices for light, medium, and heavy duty vehicles to reduce their climate change impact in Canada

International Nuclear Information System (INIS)

Fitzpatrick, N.P.

2009-01-01

The evolution of electric drive technologies from 1988, at the 9 th International Electric Vehicle Symposium (EVS 9) in Toronto, to 2007 at EVS 23 in Anaheim, is described. Total hybridization of Canada's fleet of light, medium and heavy duty vehicles would result in greenhouse reductions savings of 30 Mt of CO 2 E per year, similar to the saving from a 25% reduction in vehicle weight. Further savings in greenhouse reductions from plug-in hybrids require a battery cost similar to that needed for electric vehicles. Further development of both ultracapacitors and batteries is needed as is work on other parts of the electric drive supply chain. (author)

Electric machinery and drives in thermal power stations. Elektrische Maschinen und Antriebe in thermischen Kraftwerken

Energy Technology Data Exchange (ETDEWEB)

1974-01-01

The following subjects were dealt with during the VDE meeting: 1) Requirements made by the electric network on the generators and their excitation equipment, and the influence thereof on their design; 2) requirements made by the power station process on the electric drives and the influence thereof on type and design; 3) requirements made on protective measures from the point of the electric power station machinery.

Availability of the electric drive systems containing flux switching permanent magnet machines

NARCIS (Netherlands)

Wang, L.; Sfakianakis, G.; Paulides, J.J.H.; Lomonova, E.A.

2016-01-01

This paper investigates how to improve availability of an electrical drive containing a 3-phase 12/10 (12 stator tooth/10 rotor poles) flux switching permanent magnet machine. In this respect, Field-Oriented Control and Space-Vector Pulse-Width-Modulation strategies will be applied with 3-phase

Progress on advanced dc and ac induction drives for electric vehicles

Science.gov (United States)

Schwartz, H. J.

1982-01-01

Progress is reported in the development of complete electric vehicle propulsion systems, and the results of tests on the Road Load Simulator of two such systems representative of advanced dc and ac drive technology are presented. One is the system used in the DOE's ETV-1 integrated test vehicle which consists of a shunt wound dc traction motor under microprocessor control using a transistorized controller. The motor drives the vehicle through a fixed ratio transmission. The second system uses an ac induction motor controlled by transistorized pulse width modulated inverter which drives through a two speed automatically shifted transmission. The inverter and transmission both operate under the control of a microprocessor. The characteristics of these systems are also compared with the propulsion system technology available in vehicles being manufactured at the inception of the DOE program and with an advanced, highly integrated propulsion system upon which technology development was recently initiated.

Highly automated driving, secondary task performance, and driver state.

Science.gov (United States)

Merat, Natasha; Jamson, A Hamish; Lai, Frank C H; Carsten, Oliver

2012-10-01

A driving simulator study compared the effect of changes in workload on performance in manual and highly automated driving. Changes in driver state were also observed by examining variations in blink patterns. With the addition of a greater number of advanced driver assistance systems in vehicles, the driver's role is likely to alter in the future from an operator in manual driving to a supervisor of highly automated cars. Understanding the implications of such advancements on drivers and road safety is important. A total of 50 participants were recruited for this study and drove the simulator in both manual and highly automated mode. As well as comparing the effect of adjustments in driving-related workload on performance, the effect of a secondary Twenty Questions Task was also investigated. In the absence of the secondary task, drivers' response to critical incidents was similar in manual and highly automated driving conditions. The worst performance was observed when drivers were required to regain control of driving in the automated mode while distracted by the secondary task. Blink frequency patterns were more consistent for manual than automated driving but were generally suppressed during conditions of high workload. Highly automated driving did not have a deleterious effect on driver performance, when attention was not diverted to the distracting secondary task. As the number of systems implemented in cars increases, an understanding of the implications of such automation on drivers' situation awareness, workload, and ability to remain engaged with the driving task is important.

Theoretical Studying the Cyclic Loading of Electric Drive Parts of the Stand duo-160

Directory of Open Access Journals (Sweden)

A. A. Maltsev

2015-01-01

Full Text Available An electric drive of work rolls of the single-stand rolling mill duo-160 located in the laboratory of Bauman Moscow State Technical University (BMSTU is selected as an object of the theoretical study. After the work rolls have gripped the work-piece the torsional vibrations occur in the drive; a 5-mass dynamic model is built to determine their forms and frequencies. Equations of torsionalvibration movement of masses with time are based on the Lagrange equations of type II. The paper identifies intrinsic moments of inertia and angular stiffness of parts and units of the electric drive. The graphs of the moments of elastic forces are built taking into consideration the dampers and backlashes. A revealed transition process has shown that given amplitudes of the cyclic shear stresses arising in dangerous section of the most loaded top spindle do not exceed the limit of its endurance in this section. In case of excess revealed, it would lead to accumulation of fatigue damage in the spindle metal and to formation of fatigue crack that most probably would appear near the shaft surface rather than in the metal mass. With further using the electric drive this micro-crack would be gradually evolved into macro-crack, the working cross-sectional area of the shaft would be reduced so that there would be a spindle failure and on the surface of a fatigue fracture of its shaft a strongly marked crack growth zone and a completely broken zone would be observed.

Hybrid-Electric Passenger Car Carbon Dioxide and Fuel Consumption Benefits Based on Real-World Driving.

Science.gov (United States)

Holmén, Britt A; Sentoff, Karen M

2015-08-18

Hybrid-electric vehicles (HEVs) have lower fuel consumption and carbon dioxide (CO2) emissions than conventional vehicles (CVs), on average, based on laboratory tests, but there is a paucity of real-world, on-road HEV emissions and performance data needed to assess energy use and emissions associated with real-world driving, including the effects of road grade. This need is especially great as the electrification of the passenger vehicle fleet (from HEVs to PHEVs to BEVs) increases in response to climate and energy concerns. We compared tailpipe CO2 emissions and fuel consumption of an HEV passenger car to a CV of the same make and model during real-world, on-the-road network driving to quantify the in-use benefit of one popular full HEV technology. Using vehicle specific power (VSP) assignments that account for measured road grade, the mean CV/HEV ratios of CO2 tailpipe emissions or fuel consumption defined the corresponding HEV "benefit" factor for each VSP class (1 kW/ton resolution). Averaging over all VSP classes for driving in all seasons, including temperatures from -13 to +35 °C in relatively steep (-13.2 to +11.5% grade), hilly terrain, mean (±SD) CO2 emission benefit factors were 4.5 ± 3.6, 2.5 ± 1.7, and 1.4 ± 0.5 for city, exurban/suburban arterial and highway driving, respectively. Benefit factor magnitude corresponded to the frequency of electric-drive-only (EDO) operation, which was modeled as a logarithmic function of VSP. A combined model explained 95% of the variance in HEV benefit for city, 75% for arterial and 57% for highway driving. Benefit factors consistently exceeded 2 for VSP classes with greater than 50% EDO (i.e., only city and arterial driving). The reported HEV benefits account for real-world road grade that is often neglected in regulatory emissions and fuel economy tests. Fuel use HEV benefit factors were 1.3 and 2 for the regulatory highway (HWFET) and city (FTP) cycles, respectively, 18% and 31% higher than the EPA adjusted

Parameter design and performance analysis of shift actuator for a two-speed automatic mechanical transmission for pure electric vehicles

Directory of Open Access Journals (Sweden)

Jianjun Hu

2016-08-01

Full Text Available Recent developments of pure electric vehicles have shown that pure electric vehicles equipped with two-speed or multi-speed gearbox possess higher energy efficiency by ensuring the drive motor operates at its peak performance range. This article presents the design, analysis, and control of a two-speed automatic mechanical transmission for pure electric vehicles. The shift actuator is based on a motor-controlled camshaft where a special geometric groove is machined, and the camshaft realizes the axial positions of the synchronizer sleeve for gear engaging, disengaging, and speed control of the drive motor. Based on the force analysis of shift process, the parameters of shift actuator and shift motor are designed. The drive motor’s torque control strategy before shifting, speed governing control strategy before engaging, shift actuator’s control strategy during gear engaging, and drive motor’s torque recovery strategy after shift process are proposed and implemented with a prototype. To validate the performance of the two-speed gearbox, a test bed was developed based on dSPACE that emulates various operation conditions. The experimental results indicate that the shift process with the proposed shift actuator and control strategy could be accomplished within 1 s under various operation conditions, with shift smoothness up to passenger car standard.

Method for driving an actuator, actuator drive, and apparatus comprising an actuator

OpenAIRE

2010-01-01

An actuator driver circuit includes a drive signal source and an electrical damping element having a negative resistance connected in series with the drive signal source. A controllable switch is provided for selectively switching the electrical damping element into or put of a signal path from a drive signal source output to a driver circuit output, in order to selectively change the electrical damping of an actuator. For example, the electrical damping of a radial actuator or a focus actuat...

Electric drives in the vehicle sector. Textbook and manual. 2. enl. ed.; Elektrische Antriebe in der Fahrzeugtechnik. Lehr- und Arbeitsbuch

Energy Technology Data Exchange (ETDEWEB)

Babiel, Gerhard [FH Dortmund (Germany). Fahrzeugtechnik

2009-07-01

The text book under consideration reports on the fundamentals of power generation, energy conversion, induction engine a well as their application in drive systems such as hybrid vehicles and fuel cell vehicles. First of all, current and future energy sources for power train drives are presented and compared with one another. Subsequently, electro-chemical energy stores and energy converters such as fuel cell or double-layer condensers are considered. These energy storages and energy converters are used in electric vehicles and hybrid vehicles. Additionally, the transformer and the central topic of interest 'Electrical Engines' are considered. Not only standard machines (direct current motor, asynchronous motor, synchronous motor, linear motor) will be described but also engines which are applied in future passenger car drives and railway drives (reluctance motor, transverse flow engine, BLDC engine). Drive systems are presented by the example of an electric locomotive and a magnetic levitation transport system (superconducting MAGLEV).

Causes for torque degradation during deceleration and the effect on the driving range of battery electric vehicles

Energy Technology Data Exchange (ETDEWEB)

Lieb, Johannes [BMW PEUGEOT CITROEN ELECTRIFICATION, Muenchen (Germany); Wilde, Andreas [BMW Group, Muenchen (Germany); Baeker, Bernard [Dresden Univ. of Technology (Germany). Dept. of Vehicle Mechatronics

2012-11-01

The ability to regain considerable amounts of the kinetic energy during deceleration phases is a key aspect to increase the efficiency of battery electric vehicles (BEV). Especially in urban and highly congested areas brake energy recovery (BER) can drastically improve the vehicle's driving range. However, due to the high power peaks that go along even with moderate braking maneuvers, severe requirements are being put on the electric drivetrain. Any limitation of power in one of the components of the powertrain inevitably leads to degradation of the regenerative brake torque, thus limiting the car's energy regeneration capability. Without an integrated brake system that can compensate the torque variations during deceleration, BER may need to be decreased even further to prevent a loss of driving comfort due to dynamic changes in the vehicle's behavior. This paper deals with the causes of these torque restraints within the electric drivetrain and how they affect the energy consumption and therefore the electric driving range. A simulation environment was set up and verified based on an existing BEV to conduct parameter studies and depict the sensitivities towards environmental influences. The calculated efficiencies are based on standard drive cycles and incorporate continuous fading between regenerative braking and the use of friction brakes. Special attention was laid on the battery system since energy storage still poses a particular challenge in the development of electric vehicles. Also through the high mutual dependence of the various parameters of the battery enviromental influences become most evident. (orig.)

Predicting the Impacts of Intravehicular Displays on Driving Performance with Human Performance Modeling

Science.gov (United States)

Mitchell, Diane Kuhl; Wojciechowski, Josephine; Samms, Charneta

2012-01-01

A challenge facing the U.S. National Highway Traffic Safety Administration (NHTSA), as well as international safety experts, is the need to educate car drivers about the dangers associated with performing distraction tasks while driving. Researchers working for the U.S. Army Research Laboratory have developed a technique for predicting the increase in mental workload that results when distraction tasks are combined with driving. They implement this technique using human performance modeling. They have predicted workload associated with driving combined with cell phone use. In addition, they have predicted the workload associated with driving military vehicles combined with threat detection. Their technique can be used by safety personnel internationally to demonstrate the dangers of combining distracter tasks with driving and to mitigate the safety risks.

Environmental assessment of plug-in hybrid electric vehicles using naturalistic drive cycles and vehicle travel patterns: A Michigan case study

International Nuclear Information System (INIS)

Marshall, Brandon M.; Kelly, Jarod C.; Lee, Tae-Kyung; Keoleian, Gregory A.; Filipi, Zoran

2013-01-01

Plug-in hybrid electric vehicles (PHEVs) use grid electricity as well as on-board gasoline for motive force. These multiple energy sources make prediction of PHEV energy consumption challenging and also complicate evaluation of their environmental impacts. This paper introduces a novel PHEV energy consumption modeling approach and compares it to a second approach from the literature, each using actual trip patterns from the 2009 National Household Travel Survey (NHTS). The first approach applies distance-dependent fuel efficiency and on-road electricity consumption rates based on naturalistic or real world, driving information to determine gasoline and electricity consumption. The second uses consumption rates derived in accordance with government certification testing. Both approaches are applied in the context of a location-specific case study that focuses on the state of Michigan. The two PHEV models show agreement in electricity demand due to vehicle charging, gasoline consumption, and life cycle environmental impacts for this case study. The naturalistic drive cycle approach is explored as a means of extending location-specific driving data to supplement existing PHEV impact assessments methods. - Highlights: • Travel patterns from survey data are combined with naturalistic drive cycles. • More realistic PHEV energy modeling using these synthesized real-world drive cycles. • Methodology is demonstrated for PHEVs in Michigan but applicable for other regions. • Energy and emissions findings have major implications for PHEV standards and policy

Online Energy Management of Plug-In Hybrid Electric Vehicles for Prolongation of All-Electric Range Based on Dynamic Programming

Directory of Open Access Journals (Sweden)

Zeyu Chen

2015-01-01

Full Text Available The employed energy management strategy plays an important role in energy saving performance and exhausted emission reduction of plug-in hybrid electric vehicles (HEVs. An application of dynamic programming for optimization of power allocation is implemented in this paper with certain driving cycle and a limited driving range. Considering the DP algorithm can barely be used in real-time control because of its huge computational task and the dependence on a priori driving cycle, several online useful control rules are established based on the offline optimization results of DP. With the above efforts, an online energy management strategy is proposed finally. The presented energy management strategy concerns the prolongation of all-electric driving range as well as the energy saving performance. A simulation study is deployed to evaluate the control performance of the proposed energy management approach. All-electric range of the plug-in HEV can be prolonged by up to 2.86% for a certain driving condition. The energy saving performance is relative to the driving distance. The presented energy management strategy brings a little higher energy cost when driving distance is short, but for a long driving distance, it can reduce the energy consumption by up to 5.77% compared to the traditional CD-CS strategy.

Design and Control of the Electric Drive of the Anti- Hail Launching System

Directory of Open Access Journals (Sweden)

Gheorghe Manolea

2014-09-01

Full Text Available In the present, the Romanian anti-hail launchers are manually operated. This means that the positioning of the launcher on the two directions (azimuth and elevation are adjusted based on the commands, by the human operator. The paper describes the design, implementation and experimental results of the electric drives of the two axes by using permanent magnets synchronous motors (PMSM supplied by smart drives. The solution offers the possibility of automation and integration of the anti-hail launchers within intelligent systems.

TeenDrivingPlan effectiveness: the effect of quantity and diversity of supervised practice on teens' driving performance.

Science.gov (United States)

Mirman, Jessica H; Albert, W Dustin; Curry, Allison E; Winston, Flaura K; Fisher Thiel, Megan C; Durbin, Dennis R

2014-11-01

The large contribution of inexperience to the high crash rate of newly licensed teens suggests that they enter licensure with insufficient skills. In a prior analysis, we found moderate support for a direct effect of a web-based intervention, the TeenDrivingPlan (TDP), on teens' driving performance. The purpose of the present study was to identify the mechanisms by which TDP may be effective and to extend our understanding of how teens learn to drive. A randomized controlled trial conducted with teen permit holders and parent supervisors (N = 151 dyads) was used to determine if the effect of TDP on driver performance operated through five hypothesized mediators: (1) parent-perceived social support; (2) teen-perceived social support; (3) parent engagement; (4) practice quantity; and (5) practice diversity. Certified driving evaluators, blinded to teens' treatment allocation, assessed teens' driving performance 24 weeks after enrollment. Mediator variables were assessed on self-report surveys administered periodically over the study period. Exposure to TDP increased teen-perceived social support, parent engagement, and practice diversity. Both greater practice quantity and diversity were associated with better driving performance, but only practice diversity mediated the relationship between TDP and driver performance. Practice diversity is feasible to change and increases teens' likelihood of completing a rigorous on-road driving assessment just before licensure. Future research should continue to identify mechanisms that diversify practice driving, explore complementary ways to help families optimize the time they spend on practice driving, and evaluate the long-term effectiveness of TDP. Copyright © 2014 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

A Traction Control Strategy with an Efficiency Model in a Distributed Driving Electric Vehicle

OpenAIRE

Lin, Cheng; Cheng, Xingqun

2014-01-01

Both active safety and fuel economy are important issues for vehicles. This paper focuses on a traction control strategy with an efficiency model in a distributed driving electric vehicle. In emergency situation, a sliding mode control algorithm was employed to achieve antislip control through keeping the wheels' slip ratios below 20%. For general longitudinal driving cases, an efficiency model aiming at improving the fuel economy was built through an offline optimization stream within the tw...

Driving Simulator Development and Performance Study

OpenAIRE

Juto, Erik

2010-01-01

The driving simulator is a vital tool for much of the research performed at theSwedish National Road and Transport Institute (VTI). Currently VTI posses three driving simulators, two high fidelity simulators developed and constructed by VTI, and a medium fidelity simulator from the German company Dr.-Ing. Reiner Foerst GmbH. The two high fidelity simulators run the same simulation software, developed at VTI. The medium fidelity simulator runs a proprietary simulation software. At VTI there is...

Investigation of control system of traction electric drive with feedbacks on load

Science.gov (United States)

Kuznetsov, N. K.; Iov, I. A.; Iov, A. A.

2018-03-01

In the article, by the example of a walking excavator, the results of a study of a control system of traction electric drive with a rigid and flexible feedback on the load are mentioned. Based on the analysis of known works, the calculation scheme has been chosen; the equations of motion of the electromechanical system have been obtained, taking into account the elasticity of the rope and feedbacks on the load in the elastic element. A simulation model of this system has been developed and mathematical modeling of the transient processes to evaluate the influence of feedback on the dynamic characteristics of the mechanism and its efficiency of work was carried out. It is shown that the use of rigid and flexible feedbacks makes it possible to reduce dynamic loads in the traction mechanism and to limit the elastic oscillation of the executive mechanism in transient operating modes in comparison with the standard control system; however, there is some decrease in productivity. It has been also established that the sign-variable of the loading of the electric drive, connected with the opening of the backlashes in the gearbox due to the action of feedbacks on the load in the elastic element, under certain conditions, can lead to undesirable phenomena in the operation of the drive and a decrease in the reliability of its operation.

Self- and peer-assessments of ambulance drivers' driving performance

Directory of Open Access Journals (Sweden)

Anna Sundström

2012-07-01

Full Text Available The aim of the present study was to develop and examine the quality of the Ambulance Driver Self-assessment Questionnaire (ADSQ and the Ambulance Driver Peer-assessment Questionnaire (ADPQ measuring aspects of, driving performance, driving style and driving competence. In addition the ADSQ measures self-reflection and safety-attitudes. The aim of the study was also to examine ambulance drivers' self- and peer-assessments as well as to examine the accuracy of self-assessments by comparing self-assessed and peer-assessed driving performance, driving style and competence. 76 ambulance drivers employed at two ambulance stations in northern Sweden completed ADSQ and ADPQ. Item analyses were conducted to examine the psychometric properties of the items, and based on the results some revisions were made to improve the questionnaires. The revised questionnaires were functioning rather well, although some subscale demonstrated low internal consistency. Subscale inter-correlations provided support for construct validity. Self- and peer-assessments indicated safe driving performance and good driver competence, which is positive from a traffic safety perspective. A comparison of mean self- and peer-assessment ratings, controlling for age, gender and driving experience showed no significant differences, except for the subscale overtaking. This indicates that ambulance drivers' self-assessments are realistic in most areas.

Electric/Hybrid Vehicle Simulation

Science.gov (United States)

Slusser, R. A.; Chapman, C. P.; Brennand, J. P.

1985-01-01

ELVEC computer program provides vehicle designer with simulation tool for detailed studies of electric and hybrid vehicle performance and cost. ELVEC simulates performance of user-specified electric or hybrid vehicle under user specified driving schedule profile or operating schedule. ELVEC performs vehicle design and life cycle cost analysis.

Scrolling and driving: how an MP3 player and its aftermarket controller affect driving performance and visual behavior.

Science.gov (United States)

Lee, John D; Roberts, Shannon C; Hoffman, Joshua D; Angell, Linda S

2012-04-01

The aim of this study was to assess how scrolling through playlists on an MP3 player or its aftermarket controller affects driving performance and to examine how drivers adapt device use to driving demands. Drivers use increasingly complex infotainment devices that can undermine driving performance. The goal activation hypothesis suggests that drivers might fail to compensate for these demands, particularly with long tasks and large search set sizes. A total of 50 participants searched for songs in playlists of varying lengths using either an MP3 player or an aftermarket controller while negotiating road segments with traffic and construction in a medium-fidelity driving simulator. Searching through long playlists (580 songs) resulted in poor driving performance and required more long glances (longer than 2 s) to the device compared with other playlist lengths. The aftermarket controller also led to more long glances compared with the MP3 player. Drivers did not adequately adapt their behavior to roadway demand, as evident in their degraded driving performance. No significant performance differences were found between short playlists, the radio-tuning task, and the no-task condition. Selecting songs from long playlists undermined driving performance, and drivers did not sufficiently adapt their use of the device to the roadway demands, consistent with the goal activation hypothesis. The aftermarket controller degraded rather than enhanced performance. Infotainment systems should support drivers in managing distraction. Aftermarket controllers can have the unintended effect of making devices carried into the car less compatible with driving.These results can motivate development of new interfaces as alternatives to scrolling lists.

Driving performance at lateral system limits during partially automated driving.

Science.gov (United States)

Naujoks, Frederik; Purucker, Christian; Wiedemann, Katharina; Neukum, Alexandra; Wolter, Stefan; Steiger, Reid

2017-11-01

This study investigated driver performance during system limits of partially automated driving. Using a motion-based driving simulator, drivers encountered different situations in which a partially automated vehicle could no longer safely keep the lateral guidance. Drivers were distracted by a non-driving related task on a touch display or driving without an additional secondary task. While driving in partially automated mode drivers could either take their hands off the steering wheel for only a short period of time (10s, so-called 'Hands-on' variant) or for an extended period of time (120s, so-called 'Hands-off' variant). When the system limit was reached (e.g., when entering a work zone with temporary lines), the lateral vehicle control by the automation was suddenly discontinued and a take-over request was issued to the drivers. Regardless of the hands-off interval and the availability of a secondary task, all drivers managed the transition to manual driving safely. No lane exceedances were observed and the situations were rated as 'harmless' by the drivers. The lack of difference between the hands-off intervals can be partly attributed to the fact that most of the drivers kept contact to the steering wheel, even in the hands-off condition. Although all drivers were able to control the system limits, most of them could not explain why exactly the take-over request was issued. The average helpfulness of the take-over request was rated on an intermediate level. Consequently, providing drivers with information about the reason for a system limit can be recommended. Copyright © 2017 Elsevier Ltd. All rights reserved.

Electric Drive Discrete Control System with Automatic Switching-On Reserve for Autonomous Settlement

Directory of Open Access Journals (Sweden)

Tsytovich L.I.

2015-08-01

Full Text Available The paper aims at developing of control the water supply system’s electric drives for autonomous settlement. The system provides automatic switching to a reserve control channel at refusal of any of the functional elements of the working regulation channel. Usually, such systems have a test signal generator and analyzer to system response to their impact. This result to an increase in the structural redundancy of the system, increase its cost and increase the requirements for the staff qualification. A specific feature of the system is its ability to self-diagnosis of catastrophic malfunctions of scheme’s components and an automatic switching-on the reserve control channels, without applying any test signals to the whole complex of electrical equipment. Multi-zone integrating regulator with frequency-pulse-width modulation realizes this technical solution. Control system structure and signals timing diagrams are presented. The construction principle of adaptive interval-code synchronization device with improved noise stability to control the voltage regulators serving for smooth start-up of asynchronous motors of water pumps is considered as well. Such solution allowing increase noise stability and reliability work of the system in conditions of limited power electrical networks, which is characteristic for the autonomous settlements. The article may be of interest to specialists in the field of power electronics and information electronics, electric drives and process automation.

Performance Availability Assessment of Combined Multi Power Source Traction Drive Considering Real Operational Conditions

Directory of Open Access Journals (Sweden)

Frenkel Ilia

2016-09-01

Full Text Available The present paper deals with the vehicle’s traction electric drive, consisting of several various electric power sources. One of the main requirements for such systems are the safety and sustainable operations, achieved largely the implementation of an uninterrupted supply of the vehicle’s propulsion system with an electric power.

Do in-car devices affect experienced users' driving performance?

NARCIS (Netherlands)

Knapper, A.S.; Hagenzieker, M.P.; Brookhuis, K.A.

2014-01-01

Distracted driving is considered to be an important factor in road safety. To investigate how experienced user's driving behaviour is affected by in-vehicle technology, a fixed-base driving simulator was used. 20 participants drove twice in a rich simulated traffic environment while performing

Do in-car devices affect experienced users' driving performance?

NARCIS (Netherlands)

Knapper, A.S. Hagenzieker, M.P. & Brookhuis, K.A.

2015-01-01

Distracted driving is considered to be an important factor in road safety. To investigate how experienced user's driving behaviour is affected by in-vehicle technology, a fixed-base driving simulator was used. 20 participants drove twice in a rich simulated traffic environment while performing

On-the-road driving performance and driving-related skills in older untreated insomnia patients and chronic users of hypnotics.

Science.gov (United States)

Leufkens, T R M; Ramaekers, J G; de Weerd, A W; Riedel, W J; Vermeeren, A

2014-07-01

Many older adults report sleep problems and use of hypnotics. Several studies have shown that hypnotics can have acute adverse effects on driving the next morning. It is unclear however whether driving of chronic hypnotic users is impaired. Therapeutic effects on insomnia and development of tolerance may reduce the residual effects on driving. The present study aimed to compare actual driving performance and driving-related skills of chronic hypnotic users to good sleepers. To determine whether insomnia itself affects driving performance, driving and driving-related skills were compared between insomnia patients who do not or infrequently use hypnotics and good sleepers. Twenty-two frequent users of hypnotics (using hypnotics ≥ 4 nights per week for more than 3 months), 20 infrequent users (using hypnotics ≤ 3 nights per week), and 21 healthy, age-matched controls participated in this study. On the night before testing, all subjects were hospitalized for an 8-h sleep recorded by polysomnography. Frequent hypnotic users used their regular medication at bedtime (2330 hours), while infrequent users and controls received no medication. Cognitive performance (word learning, digit span, tracking, divided attention, vigilance, and inhibitory control) was assessed 8.5 h and driving performance between 10 and 11 h after bedtime and dosing. Polysomnographic recordings did not significantly differ between the groups, but the insomnia patients, treated or untreated, still reported subjective sleep complaints. Results show no differences in driving performance and driving-related skills between both groups of insomnia patients and controls. Driving performance in chronic users of hypnotics and untreated insomnia patients is not impaired. For chronic users, this may be due to prescription of relatively safe drugs and low doses. For untreated insomniacs, this corroborates previous findings showing an absence of neuropsychological deficits in this group of patients.

Gender differences in alcohol impairment of simulated driving performance and driving-related skills.

Science.gov (United States)

Miller, Melissa A; Weafer, Jessica; Fillmore, Mark T

2009-01-01

Considerable laboratory research indicates that moderate doses of alcohol impair a broad range of skilled activities related to driving performance in young adults. Although laboratory studies show that the intensity of impairment is generally dependent on the blood alcohol concentration, some reviews of this literature suggest that women might be more sensitive to the impairing effects of alcohol than men. The present study tested this hypothesis. Drawing on data from previous experiments in our laboratory, we compared men and women in terms of the degree to which a challenge dose of alcohol (0.65 g/kg) impaired their simulated driving performance and measures of three separate behavioral and cognitive functions important to driving performance: motor coordination, speed of information processing and information-processing capacity. Alcohol significantly impaired all aspects of performance. Moreover, women displayed greater impairment than men on all behavioral tests and also reported higher levels of subjective intoxication compared with men. Both biological and social-cultural factors have been implicated in gender differences in the behavioral responses to alcohol. The current evidence of heightened sensitivity to alcohol in women highlights the need for better understanding the biological and environmental factors underlying this gender difference.

Energy Management Strategy Based on the Driving Cycle Model for Plugin Hybrid Electric Vehicles

Directory of Open Access Journals (Sweden)

Xiaoling Fu

2014-01-01

Full Text Available The energy management strategy (EMS for a plugin hybrid electric vehicle (PHEV is proposed based on the driving cycle model and dynamic programming (DP algorithm. A driving cycle model is constructed by collecting and processing the driving data of a certain school bus. The state of charge (SOC profile can be obtained by the DP algorithm for the whole driving cycle. In order to optimize the energy management strategy in the hybrid power system, the optimal motor torque control sequence can be calculated using the DP algorithm for the segments between the traffic intersections. Compared with the traditional charge depleting-charge sustaining (CDCS strategy, the test results on the ADVISOR platform show a significant improvement in fuel consumption using the EMS proposed in this paper.

Performance of a Fuel-Cell-Powered, Small Electric Airplane Assessed

Science.gov (United States)

Berton, Jeffrey J.

2004-01-01

Rapidly emerging fuel-cell-power technologies may be used to launch a new revolution of electric propulsion systems for light aircraft. Future small electric airplanes using fuel cell technologies hold the promise of high reliability, low maintenance, low noise, and - with the exception of water vapor - zero emissions. An analytical feasibility and performance assessment was conducted by NASA Glenn Research Center's Airbreathing Systems Analysis Office of a fuel-cell-powered, propeller-driven, small electric airplane based on a model of the MCR-01 two-place kitplane (Dyn'Aero, Darois, France). This assessment was conducted in parallel with an ongoing effort by the Advanced Technology Products Corporation and the Foundation for Advancing Science and Technology Education. Their project - partially funded by a NASA grant - is to design, build, and fly the first manned, continuously propelled, nongliding electric airplane. In our study, an analytical performance model of a proton exchange membrane (PEM) fuel cell propulsion system was developed and applied to a notional, two-place light airplane modeled after the MCR-01 kitplane. The PEM fuel cell stack was fed pure hydrogen fuel and humidified ambient air via a small automotive centrifugal supercharger. The fuel cell performance models were based on chemical reaction analyses calibrated with published data from the fledgling U.S. automotive fuel cell industry. Electric propeller motors, rated at two shaft power levels in separate assessments, were used to directly drive a two-bladed, variable-pitch propeller. Fuel sources considered were compressed hydrogen gas and cryogenic liquid hydrogen. Both of these fuel sources provided pure, contaminant-free hydrogen for the PEM cells.

Performance of an active electric bearing for rotary micromotors

International Nuclear Information System (INIS)

Han, F T; Wang, L; Wu, Q P; Liu, Y F

2011-01-01

An electric bearing used to support a micromachined rotor of variable-capacitance motors was designed and tested in order to study the characteristics of this frictionless bearing. Electrostatic suspension of a ring-shaped rotor in five degrees of freedom is required to eliminate the mechanical bearing and thus the friction and wear between the rotor and the substrate. Bulk microfabrication-based glass/silicon/glass bonding is chosen for this device, allowing the fabrication of large area sense capacitors and rotor, which make the device potentially suitable for the development of an electrostatically suspended micromachined gyroscope. The device and its basic operating principle are described, as well as the dynamics of the rotor and basic design considerations of the electric bearing system. A theoretical relationship to relate the characteristics of a classical lag–lead compensator to the stiffness properties of the electric bearing is developed to explain the experimental bearing measurements. The experimental results of closed-loop frequency response, suspension stiffness and drive voltage effects are presented and discussed for the bearing operated initially in the atmospheric environment. The performance of a tri-axial electrostatic accelerometer has also been experimentally investigated on the prototype of the electric bearing system

Predicting psychopharmacological drug effects on actual driving performance (SDLP) from psychometric tests measuring driving-related skills.

Science.gov (United States)

Verster, Joris C; Roth, Thomas

2012-03-01

There are various methods to examine driving ability. Comparisons between these methods and their relationship with actual on-road driving is often not determined. The objective of this study was to determine whether laboratory tests measuring driving-related skills could adequately predict on-the-road driving performance during normal traffic. Ninety-six healthy volunteers performed a standardized on-the-road driving test. Subjects were instructed to drive with a constant speed and steady lateral position within the right traffic lane. Standard deviation of lateral position (SDLP), i.e., the weaving of the car, was determined. The subjects also performed a psychometric test battery including the DSST, Sternberg memory scanning test, a tracking test, and a divided attention test. Difference scores from placebo for parameters of the psychometric tests and SDLP were computed and correlated with each other. A stepwise linear regression analysis determined the predictive validity of the laboratory test battery to SDLP. Stepwise regression analyses revealed that the combination of five parameters, hard tracking, tracking and reaction time of the divided attention test, and reaction time and percentage of errors of the Sternberg memory scanning test, together had a predictive validity of 33.4%. The psychometric tests in this test battery showed insufficient predictive validity to replace the on-the-road driving test during normal traffic.

Driving with electrical power

International Nuclear Information System (INIS)

Ursin, M.; Hoeckel, M.

2008-01-01

This article takes a look at the chances offered to the electricity supply industry by the increasing use of battery-driven vehicles - and the advantages thus offered to the environment. The use of the vehicles' batteries to form a distributed electricity storage scheme is discussed. The authors comment that, although electrically-driven vehicles consume more power, the total primary energy consumption and pollutant emissions will be reduced. The actual electricity consumption of electric vehicles and the source of this power are examined. Power saved by the reduced use of electrical heating systems and boilers could, according to the authors, be used to charge the batteries of electric vehicles. The use of these batteries as a storage system to help regulate electricity supplies is discussed and the steps to be taken for the implementation of such a system are listed

Effects of chewing gum on driving performance as evaluated by the STISIM driving simulator

OpenAIRE

Yoo, Ingyu; Kim, Eun-Joo; Lee, Joo-Hyun

2015-01-01

[Purpose] The purpose of this study was to determine the effects of chewing gum on driving performance in a driving simulator. [Subjects] In total, 26 young licensed drivers participated. [Methods] The driving scenario was typical of an urban environment: a single-carriageway, two-way road consisting of a mix of curved and straight sections, with considerable levels of traffic, pedestrians, and parked cars. Mean distance driven above the speed limit, lane position, mean distance driven across...

To the Problem of Electromechanical Interaction in Elevators with Controlled Electric Drive and Fuzzy Speed Controller

Directory of Open Access Journals (Sweden)

A. S. Koval

2010-01-01

Full Text Available The paper considers problems concerning electromechanical interaction in elevators with an adjustable asynchronous electric drive equipped with the vector control systems under direct torque control and direct torque control with pulse-width modulator. A mathematical description of electromechanical elevator system with due account of nonlinearity of the worm gear is given in the paper. The paper presents a simplified circuit design of a control system with a fuzzy speed controller. It has been established that the factor of electromechanical interaction in electromechanical system with the adjustable asynchronous electric drive and an fuzzy speed controller is within the range which corresponds to existence of the essential electromechanical interaction.

A DCT-Based Driving Cycle Generation Method and Its Application for Electric Vehicles

Directory of Open Access Journals (Sweden)

Cheng Lin

2015-01-01

Full Text Available Nowadays, many widely used driving cycle (DC representing and generating methods are designed for traditional vehicles with internal combustion engines (ICE. The real-world driving is viewed as a sequence of acceleration, cruise, deceleration, and idle modes. The emission and fuel consumption in each period should be taken into account carefully. However, for electric vehicles (EVs, most of them are powered by low or zero-emission renewable energy sources. The working status and energy management algorithms of them are very different from traditional vehicles. To facilitate the EV design, we proposed a novel DC representing and construction method to generate DCs for EVs. The whole driving route is divided into several length-fixed segments and each of these segments is converted into a frequency sequence. After doing that, we can adjust the frequency and amplitude of the generated driving cycle directly. The experiment results showed that the proposed method was effective and convenient.

Effects of alcohol on automated and controlled driving performances.

Science.gov (United States)

Berthelon, Catherine; Gineyt, Guy

2014-05-01

Alcohol is the most frequently detected substance in fatal automobile crashes, but its precise mode of action is not always clear. The present study was designed to establish the influence of blood alcohol concentration as a function of the complexity of the scenarios. Road scenarios implying automatic or controlled driving performances were manipulated in order to identify which behavioral parameters were deteriorated. A single blind counterbalanced experiment was conducted on a driving simulator. Sixteen experienced drivers (25.3 ± 2.9 years old, 8 men and 8 women) were tested with 0, 0.3, 0.5, and 0.8 g/l of alcohol. Driving scenarios varied: road tracking, car following, and an urban scenario including events inspired by real accidents. Statistical analyses were performed on driving parameters as a function of alcohol level. Automated driving parameters such as standard deviation of lateral position measured with the road tracking and car following scenarios were impaired by alcohol, notably with the highest dose. More controlled parameters such as response time to braking and number of crashes when confronted with specific events (urban scenario) were less affected by the alcohol level. Performance decrement was greater with driving scenarios involving automated processes than with scenarios involving controlled processes.

Time-dependent plug-in hybrid electric vehicle charging based on national driving patterns and demographics

International Nuclear Information System (INIS)

Kelly, Jarod C.; MacDonald, Jason S.; Keoleian, Gregory A.

2012-01-01

Highlights: ► Analyzed National Household Travel Survey to simulate driving and charging patterns. ► Average compact PHEVs used 49 kW h of electricity and 6.8 L of gasoline per week. ► Percent of electrically driven miles increased from 64.3 in 2001 to 66.7 in 2009. ► Investigated demographic effects of sex, age, income, and household location. ► Analysis shows higher utility factors for females versus males and high age variation. -- Abstract: Plug-in hybrid electric vehicles (PHEVs) are one promising technology for addressing concerns around petroleum consumption, energy security and greenhouse gas emissions. However, there is much uncertainty in the impact that PHEVs can have on energy consumption and related emissions, as they are dependent on vehicle technology, driving patterns, and charging behavior. A methodology is used to simulate PHEV charging and gasoline consumption based on driving pattern data in USDOT’s National Household Travel Survey. The method uses information from each trip taken by approximately 170,000 vehicles to track their battery state of charge throughout the day, and to determine the timing and quantity of electricity and gasoline consumption for a fleet of PHEVs. Scenarios were developed to examine the effects of charging location, charging rate, time of charging and battery size. Additionally, demographic information was examined to see how driver and household characteristics influence consumption patterns. Results showed that a compact vehicle with a 10.4 kW h useable battery (approximately a 42 mile [68 km] all electric range) travels between 62.5% and 75.7% on battery electricity, depending on charging scenario. The percent of travel driven electrically (Utility Factor, UF) in a baseline charging scenario increased from 64.3% using 2001 NHTS data to 66.7% using 2009 data. The average UF was 63.5% for males and 72.9% for females and in both cases they are highly sensitive to age. Vehicle charging load profiles across

The PEGASUS Drive: A nuclear electric propulsion system for the space exploration initiative

International Nuclear Information System (INIS)

Coomes, E.P.; Dagle, J.E.

1991-01-01

The advantages of using electric propulsion for propulsion are well-known in the aerospace community. The high specific impulse, lower propellant requirements, and lower system mass make it a very attractive propulsion option for the Space Exploration Initiative (SEI), especially for the transport of cargo. One such propulsion system is the PEGASUS Drive (Coomes et al. 1987). In its original configuration, the PEGASUS Drive consisted of a 10-MWe power source coupled to a 6-MW magnetoplasmadynamic (MPD) thruster system. The PEGASUS Drive propelled a manned vechicle to Mars and back in 601 days. By removing the crew and their associated support systems from the space craft and by incorporating technology advances in reactor design and heat rejection systems, a second generation PEGASUS Drive can be developed with an alpha less than two. Utilizing this propulsion system, a 400-MT cargo vechicle, assembled and loaded in low Earth orbit (LEO), could deliver 262 MT of supplies and hardware to MARS 282 days after escaping Earth orbit. Upon arrival at Mars the transport vehicle would place its cargo in the desired parking orbit around Mars and then proceed to synchronous orbit above the desired landing sight. Using a laser transmitter, PEGASUS could provide 2-MW on the surface to operate automated systems deployed earlier and then provide surface power to support crew activities after their arrival. The additional supplies and hardware, coupled with the availability of megawatt levels of electric power on the Mars surface, would greatly enhance and even expand the mission options being considered under SEI

Improving Motor and Drive System Performance – A Sourcebook for Industry

Energy Technology Data Exchange (ETDEWEB)

None

2014-02-01

This sourcebook outlines opportunities to improve motor and drive systems performance. The sourcebook is divided into four main sections: (1) Motor and Drive System Basics: Summarizes important terms, relationships, and system design considerations relating to motor and drive systems. (2) Performance Opportunity Road Map: Details the key components of well-functioning motor and drive systems and opportunities for energy performance opportunities. (3) Motor System Economics: Offers recommendations on how to propose improvement projects based on corporate priorities, efficiency gains, and financial payback periods. (4) Where to Find Help: Provides a directory of organizations associated with motors and drives, as well as resources for additional information, tools, software, videos, and training opportunities.

Comparison of Plug-In Hybrid Electric Vehicle Battery Life Across Geographies and Drive-Cycles

International Nuclear Information System (INIS)

Smith, K.; Warleywine, M.; Wood, E.; Neubauer, J.; Pesaran, A.

2012-01-01

In a laboratory environment, it is cost prohibitive to run automotive battery aging experiments across a wide range of possible ambient environment, drive cycle and charging scenarios. Since worst-case scenarios drive the conservative sizing of electric-drive vehicle batteries, it is useful to understand how and why those scenarios arise and what design or control actions might be taken to mitigate them. In an effort to explore this problem, this paper applies a semi-empirical life model of the graphite/nickel-cobalt-aluminum lithium-ion chemistry to investigate impacts of geographic environments under storage and simplified cycling conditions. The model is then applied to analyze complex cycling conditions, using battery charge/discharge profiles generated from simulations of PHEV10 and PHEV40 vehicles across 782 single-day driving cycles taken from Texas travel survey data.

Driving simulator performance of veterans from the Iraq and Afghanistan wars.

Science.gov (United States)

Amick, Melissa M; Kraft, Melissa; McGlinchey, Regina

2013-01-01

Driving simulator performance was examined in Operation Iraqi Freedom/Operation Enduring Freedom (OIF/OEF) Veterans to objectively evaluate driving abilities among this cohort who self-report poorer driving safety postdeployment. OIF/OEF Veterans (n = 25) and age- and education-matched civilian controls (n = 25) participated in a 30 min driving simulator assessment that measured the frequency of minor, moderate, and severe driving errors. Frequency of errors in specific content domains (speed regulation, positioning, and signaling) was also calculated. All participants answered questions about number of lifetime traffic "warnings," moving violation tickets, and accidents. Veterans completed the Posttraumatic Stress Disorder (PTSD) Checklist-Military Version. On the driving simulator assessment, Veterans committed more minor, moderate, severe, and speeding errors and reported poorer lifetime driving records than the civilian control group. Exploratory analyses revealed an association between increasing errors on the driving simulator with increasing symptoms of PTSD, although statistically this correlation did not reach significance. These findings suggest that Veterans perform more poorly on an objective evaluation of driving safety and that the presence of PTSD could be associated with worse performance on this standardized driving simulator assessment.

Do in-car devices affect experienced users' driving performance?

Directory of Open Access Journals (Sweden)

Allert S. Knapper

2015-07-01

Full Text Available Distracted driving is considered to be an important factor in road safety. To investigate how experienced user's driving behaviour is affected by in-vehicle technology, a fixed-base driving simulator was used. 20 participants drove twice in a rich simulated traffic environment while performing secondary, i.e. mobile phone and navigation system tasks. The results show that mean speed was lower in all experimental conditions, compared to baseline driving, while subjective effort increased. Lateral performance deteriorated only during visual–manual tasks, i.e. texting and destination entry, in which the participants glanced off the forward road for a substantial amount of time. Being experienced in manipulating in-car devices does not solve the problem of dual tasking when the primary task is a complex task like driving a moving vehicle. The results and discussion may shed some light on the current debate regarding phone use hazards.

Mechatronics in electric machinery and drives; 2. ed.; Mechatronik in elektrischen Maschinen und Antrieben

Energy Technology Data Exchange (ETDEWEB)

Gutt, H.J. [comp.

1995-12-31

Mechatronics is a novel field of work (characterized by closely interlocked and interdisciplinary collaboration among university faculties, institutes, and industrial enterprise) in which activities so far have been harvesting unexpectedly successful results in terms of synergetic effects marking a signpost to the future in many fields of application. Electric machines and drives play a major role in this process as the link between the field of electrical engineering and mechanics on the one hand, and technical computer science on the other. In driving systems, many accessory components such as electronic components or sensors can be saved by skilful and purposeful selection and combination, and design, of electric driving mechanisms and actuators. One contribution in this report presents an interesting case showing that employment of an unconventional synchronous motor can replace all electronic instrumentation hitherto used for run up and monitoring. Another contribution shows that the electric machines can be used for twofold tasks, also serving as essential information sources in combination with neural networks, an emerging development that may have a brilliant future. (orig./GL) [Deutsch] Die Mechatronik (d.h. das engverzahnte interdisziplinaere Zusammenwirken mehrerer Fakultaeten, Institute und interessierter Industrieunternehmen) zeigt zukunftsweisend auf vielfaeltigen Einsatzgebieten unerwartete synergetische Erfolge. Eine wesentliche Schluesselrolle kommt hierbei den elektrischen Maschinen und Antrieben als Bindeglied der Elektrotechnik zwischen der Mechanik einerseits und der Informatik andererseits zu. In kompletten Antriebssystemen allein durch die geschickte Wahl und Gestaltung der elektrischen Antriebsmaschinen und Aktoren zugleich viele, bisher additiv verwendete Komponenten der Sensorik und Eletronik eingespart werden koennen. Ausserdem wird ein Extremfall der Verbilligung dargestellt, in dem unter Verwendung eines unkonventionellen Synchronmotors

Improving the performance of a hybrid electric vehicle by utilization regenerative braking energy of vehicle

Energy Technology Data Exchange (ETDEWEB)

Mourad, Mohamed [Automotive and Tractors Department, Faculty of Engineering, Minia University (Egypt)

2011-07-01

Environmentally friendly vehicles with range and performance capabilities surpassing those of conventional ones require a careful balance among competing goals for fuel efficiency, performance and emissions. It can be recuperated the energy of deceleration case of the vehicle to reuse it to recharge the storage energy of hybrid electric vehicle and increase the state of charge of batteries under the new conditions of vehicle operating in braking phase. Hybrid electric vehicle has energy storage which allows decreasing required peak value of power from prime mover, which is the internal combustion engine. The paper investigates the relationships between the driving cycle phases and the recuperation energy to the batteries system of hybrid electric vehicle. This work describes also a methodology for integrating this type of hybrid electric vehicle in a simulation program. A design optimization framework is then used to find the best position that we can utilize the recuperation energy to recharge the storage batteries of hybrid electric vehicle.

Leukoaraiosis significantly worsens driving performance of ordinary older drivers.

Directory of Open Access Journals (Sweden)

Kimihiko Nakano

Full Text Available BACKGROUND: Leukoaraiosis is defined as extracellular space caused mainly by atherosclerotic or demyelinated changes in the brain tissue and is commonly found in the brains of healthy older people. A significant association between leukoaraiosis and traffic crashes was reported in our previous study; however, the reason for this is still unclear. METHOD: This paper presents a comprehensive evaluation of driving performance in ordinary older drivers with leukoaraiosis. First, the degree of leukoaraiosis was examined in 33 participants, who underwent an actual-vehicle driving examination on a standard driving course, and a driver skill rating was also collected while the driver carried out a paced auditory serial addition test, which is a calculating task given verbally. At the same time, a steering entropy method was used to estimate steering operation performance. RESULTS: The experimental results indicated that a normal older driver with leukoaraiosis was readily affected by external disturbances and made more operation errors and steered less smoothly than one without leukoaraiosis during driving; at the same time, their steering skill significantly deteriorated. CONCLUSIONS: Leukoaraiosis worsens the driving performance of older drivers because of their increased vulnerability to distraction.

Hybrid propulsion testing using direct-drive electrical machines for super yacht and inland shipping

NARCIS (Netherlands)

Paulides, J.J.H.; Djukic, N.; de Roon, J.A.; Encica, L.

2016-01-01

Hybrid or full electric propulsions for inland ships are becoming more popular. In these application, direct-drive PM propulsion motors are a preferred machine configuration. This paper discusses the challenges to determine the losses, as estimated with simulations, during the testing procedures of

Introducing a multivariate model for predicting driving performance: the role of driving anger and personal characteristics.

Science.gov (United States)

Roidl, Ernst; Siebert, Felix Wilhelm; Oehl, Michael; Höger, Rainer

2013-12-01

Maladaptive driving is an important source of self-inflicted accidents and this driving style could include high speeds, speeding violations, and poor lateral control of the vehicle. The literature suggests that certain groups of drivers, such as novice drivers, males, highly motivated drivers, and those who frequently experience anger in traffic, tend to exhibit more maladaptive driving patterns compared to other drivers. Remarkably, no coherent framework is currently available to describe the relationships and distinct influences of these factors. We conducted two studies with the aim of creating a multivariate model that combines the aforementioned factors, describes their relationships, and predicts driving performance more precisely. The studies employed different techniques to elicit emotion and different tracks designed to explore the driving behaviors of participants in potentially anger-provoking situations. Study 1 induced emotions with short film clips. Study 2 confronted the participants with potentially anger-inducing traffic situations during the simulated drive. In both studies, participants who experienced high levels of anger drove faster and exhibited greater longitudinal and lateral acceleration. Furthermore, multiple linear regressions and path-models revealed that highly motivated male drivers displayed the same behavior independent of their emotional state. The results indicate that anger and specific risk characteristics lead to maladaptive changes in important driving parameters and that drivers with these specific risk factors are prone to experience more anger while driving, which further worsens their driving performance. Driver trainings and anger management courses will profit from these findings because they help to improve the validity of assessments of anger related driving behavior. © 2013.

Marijuana, alcohol and actual driving performance

Science.gov (United States)

1999-07-01

The purpose of this study was to empirically determine the separate and combined effects of Delta-9-tetrahydrocannabinol (THC) and alcohol on actual driving performance. This was the first study ever in which the drugs' combined effects were measured...

A traction control strategy with an efficiency model in a distributed driving electric vehicle.

Science.gov (United States)

Lin, Cheng; Cheng, Xingqun

2014-01-01

Both active safety and fuel economy are important issues for vehicles. This paper focuses on a traction control strategy with an efficiency model in a distributed driving electric vehicle. In emergency situation, a sliding mode control algorithm was employed to achieve antislip control through keeping the wheels' slip ratios below 20%. For general longitudinal driving cases, an efficiency model aiming at improving the fuel economy was built through an offline optimization stream within the two-dimensional design space composed of the acceleration pedal signal and the vehicle speed. The sliding mode control strategy for the joint roads and the efficiency model for the typical drive cycles were simulated. Simulation results show that the proposed driving control approach has the potential to apply to different road surfaces. It keeps the wheels' slip ratios within the stable zone and improves the fuel economy on the premise of tracking the driver's intention.

A Traction Control Strategy with an Efficiency Model in a Distributed Driving Electric Vehicle

Science.gov (United States)

Lin, Cheng

2014-01-01

Both active safety and fuel economy are important issues for vehicles. This paper focuses on a traction control strategy with an efficiency model in a distributed driving electric vehicle. In emergency situation, a sliding mode control algorithm was employed to achieve antislip control through keeping the wheels' slip ratios below 20%. For general longitudinal driving cases, an efficiency model aiming at improving the fuel economy was built through an offline optimization stream within the two-dimensional design space composed of the acceleration pedal signal and the vehicle speed. The sliding mode control strategy for the joint roads and the efficiency model for the typical drive cycles were simulated. Simulation results show that the proposed driving control approach has the potential to apply to different road surfaces. It keeps the wheels' slip ratios within the stable zone and improves the fuel economy on the premise of tracking the driver's intention. PMID:25197697

Bosch automotive electrics and automotive electronics systems and components, networking and hybrid drive

CERN Document Server

2014-01-01

The significance of electrical and electronic systems has increased considerably in the last few years and this trend is set to continue. The characteristics feature of innovative systems is the fact that they can work together in a network. This requires powerful bus systems that the electronic control units can use to exchange information. Networking and the various bus systems used in motor vehicles are the prominent new topic in the 5th edition of the "Automotive Electric, Automotive Electronics" technical manual. The existing chapters have also been updated, so that this new edition brings the reader up to date on the subjects of electrical and electronic systems in the motor vehicle. Content Electrical and electronical systems – Basic principles of networking - Examples of networked vehicles – Bus systems – Architecture of electronic systems – Mechatronics – Elektronics – Electronic control Units – Software – Sensors – Actuators – Hybrid drives – Vehicle electrical system – Start...

Performance evaluation of a transformerless multiphase electric submersible pump system

Directory of Open Access Journals (Sweden)

Ahmed A. Hakeem

2014-08-01

Full Text Available Using of low-voltage variable-frequency drive followed by a step-up transformer is the most preferable way to feed an electrical submersible pump motor. The existence of long feeder between the motor and drive systems usually causes over-voltage problems because of the travelling wave phenomenon, which makes the employment of filter networks on the motor or inverter terminals mandatory. The so-called boost-inverter inherently can solve this problem with filter-less operation as it offers a direct sinusoidal output voltage. As boost inverters have voltage boosting capability, it can provide a transformer-less operation as well. This study investigates the performance of a five-phase modular winding induction machine fed from a boost-inverter through a long feeder. A simulation study using a 1000 Hp system and experimental investigation on a 1 Hp prototype machine are used to support the presented approach.

Converted vehicle for battery electric drive. Aspects on the design of the software-driven vehicle control unit

Energy Technology Data Exchange (ETDEWEB)

Giessler, Martin; Paul, Jens; Gauterin, Frank [Karlsruher Institut fuer Technologie (KIT), Karlsruhe (Germany). Inst. fuer Fahrzeugsystemtechnik (FAST); Fritz, Alexander; Sander, Oliver; Mueller-Glaser, Klaus D. [Karlsruher Institut fuer Technologie (KIT), Karlsruhe (Germany). Inst. fuer Technik der Informationsverarbeitung (ITIV)

2012-11-01

At the Karlsruher Institute of Technology (KIT) a vehicle was converted for full battery electric drive within a cooperation of several faculties under the direction of the chair of vehicle technology. Within this paper the developed software to control the main functions of the vehicle will be presented and potentials to increase the energy efficiency will be discussed. The software based vehicle control unit is the central control unit to realize drivers command with respect to the system parameters, which are important for safety, dynamics, range and comfort of the vehicle. The structure of the software architecture, the interaction with the main electric vehicle specific control units and components and the main implemented functions will be described within this paper. The converted vehicle consists mainly of one electric motor with water cooled power electronics that drives the front axle, 21 battery modules controlled and managed by the battery management system, one on board charging device and an universal control unit. Not only strategies for power recovery while braking, but also strategies for driving and operation can help increase the energy efficiency. Select measures to recover and safe energy are also shown. (orig.)

Radio-frequency current drive efficiency in the presence of ITBs and a dc electric field

Science.gov (United States)

Rosa, P. R. da S.; Mourão, R.; Ziebell, L. F.

2009-05-01

This paper discusses the current drive efficiency by the combined action of EC and LH waves in the presence of a dc electric field and transport, with an internal transport barrier. The transport is assumed to be produced by magnetic fluctuations. The study explores the different barrier parameters and their influence on the current drive efficiency. We study the subject by numerically solving the Fokker-Planck equation. Our main result is that the barrier depth and barrier width are important to determine the correct shape of the current density profile but not to determine the current drive efficiency, which is very little influenced by these parameters. We also found similar results for the influence of the level of magnetic fluctuations on the current density profile and on the current drive efficiency.

Radio-frequency current drive efficiency in the presence of ITBs and a dc electric field

International Nuclear Information System (INIS)

Rosa, P.R. da S; Mourao, R.; Ziebell, L.F.

2009-01-01

This paper discusses the current drive efficiency by the combined action of EC and LH waves in the presence of a dc electric field and transport, with an internal transport barrier. The transport is assumed to be produced by magnetic fluctuations. The study explores the different barrier parameters and their influence on the current drive efficiency. We study the subject by numerically solving the Fokker-Planck equation. Our main result is that the barrier depth and barrier width are important to determine the correct shape of the current density profile but not to determine the current drive efficiency, which is very little influenced by these parameters. We also found similar results for the influence of the level of magnetic fluctuations on the current density profile and on the current drive efficiency.

Dynamics and control of electrical drives

Energy Technology Data Exchange (ETDEWEB)

Wach, Piotr [Politechnika Opolska, Opole (Poland). Inst. of Electromechanical Systems and Applied Informatics

2011-07-01

Dynamics is a science concerned with movement and changes. In the most general approach it relates to life processes as well as behavior in nature in rest. It governs small particles, technical objects, conversion of matter and materials but also concerns people, groups of people in their individual and, in particular, social dimension. In dynamics we always have to do with causes or stimuli for motion, the rules of reaction or behavior and its result in the form of trajectory of changes. This book is devoted to dynamics of a wide class of specific but very important objects such as electromechanical systems. This is a very rigorous discipline and has a long tradition, as its theoretical bases were formulated in the first half of the XIX century by d' Alembert, Lagrange, Hamilton, Maxwell and other prominent scientists, but their crucial results were based on previous pioneering research of others such as Copernicus, Galileo, Newton..This book in its theoretical foundations is based on the principle of least action which governs classical as well as relativistic mechanics and electromagnetism and leads to Lagrange's equations which are applied in the book as universal method to construct equations of motion of electromechanical systems. It gives common and coherent grounds to formulate mathematical models for all lumped parameters' electromechanical systems, which are vital in our contemporary industry and civilized everyday life. From these remarks it seems that the book is general and theoretical but in fact it is a very practical one concerning modern electrical drives in a broad sense, including electromechanical energy conversion, induction motor drives, brushless DC drives with a permanent magnet excitation and switched reluctance machines (SRM). And of course their control, which means shaping of their trajectories of motion using modern tools, their designed autonomy in keeping a track according to our programmed expectations. The problems

Electric motor handbook

CERN Document Server

Chalmers, B J

2013-01-01

Electric Motor Handbook aims to give practical knowledge in a wide range of capacities such as plant design, equipment specification, commissioning, operation and maintenance. The book covers topics such as the modeling of steady-state motor performance; polyphase induction, synchronous, and a.c. commutator motors; ambient conditions, enclosures, cooling and loss dissipation; and electrical supply systems and motor drives. Also covered are topics such as variable-speed drives and motor control; materials and motor components; insulation types, systems, and techniques; and the installation, sit

Plug-in hybrid electric vehicle LiFePO4 battery life implications of thermal management, driving conditions, and regional climate

Science.gov (United States)

Yuksel, Tugce; Litster, Shawn; Viswanathan, Venkatasubramanian; Michalek, Jeremy J.

2017-01-01

Battery degradation strongly depends on temperature, and many plug-in electric vehicle applications employ thermal management strategies to extend battery life. The effectiveness of thermal management depends on the design of the thermal management system as well as the battery chemistry, cell and pack design, vehicle system characteristics, and operating conditions. We model a plug-in hybrid electric vehicle with an air-cooled battery pack composed of cylindrical LiFePO4/graphite cells and simulate the effect of thermal management, driving conditions, regional climate, and vehicle system design on battery life. We estimate that in the absence of thermal management, aggressive driving can cut battery life by two thirds; a blended gas/electric-operation control strategy can quadruple battery life relative to an all-electric control strategy; larger battery packs can extend life by an order of magnitude relative to small packs used for all-electric operation; and batteries last 73-94% longer in mild-weather San Francisco than in hot Phoenix. Air cooling can increase battery life by a factor of 1.5-6, depending on regional climate and driving patterns. End of life criteria has a substantial effect on battery life estimates.

Electric driving. An attractive challenge; Elektrisch autorijden. Evaluatie van transities op basis van systeemopties

Energy Technology Data Exchange (ETDEWEB)

Nagelhout, D.; Ros, J.P.M.

2009-01-15

Over the past years, electric driving has become more and more attractive because of the development of better batteries. Driving electric vehicles could drastically reduce CO2 emissions, especially if more electricity would be generated by using sustainable energy. As most passenger cars are not used at night, this is the ideal time for charging their batteries. This would be cost-effective because, at that time, there is a surplus of generating capacity, and wind energy could also be used more effectively. Moreover, consumers will be able to drive clean and quiet vehicles at costs that seem surmountable in the future. At least two obstacles still need to be overcome. The first of which is the current maximum range of electric vehicles of around a few hundred kilometres. Battery producers and universities are working hard on the development of batteries that could be charged within 5 to 10 minutes at EV fast-charge stations. This limited range would not be a drawback for the so-called plug-in hybrid electric vehicles (PHEVs), which can run on both fossil fuel and electric power, and are expected to come onto the market in the near future. However, these plug-in hybrids reduce less CO2 and carry slightly higher costs. The second obstacle is the need for a standardised European network of charging stations, and electrical outlets near residences and at commercial and public parking facilities. This report shows the challenges facing the government and the business community of utilising the benefits of electric driving and of overcoming the obstacles. [Dutch] Elektrische auto's - in combinatie met een elektriciteitsproductie op basis van vernieuwbare bronnen en schoon fossiel - hebben de potentie om op lange termijn de CO2-emissie van personenauto's en andere lichte voertuigen met 80-90% terug te brengen. Elektrisch vervoer kan ook de geluidhinder in de stad aanmerkelijk terugdringen. De kosten lijken hiervoor geen beletsel te zijn, want de verwachting is

Effect of the teen driving plan on the driving performance of teenagers before licensure: a randomized clinical trial.

Science.gov (United States)

Mirman, Jessica H; Curry, Allison E; Winston, Flaura K; Wang, Wenli; Elliott, Michael R; Schultheis, Maria T; Fisher Thiel, Megan C; Durbin, Dennis R

2014-08-01

Many studies have failed to show an effect of parent-supervised practice driving on the driving performance of teenagers; nevertheless, most Graduated Driver Licensing programs have provisions that require supervised practice. To determine whether a web-based intervention, the Teen Driving Plan (TDP), can improve the driving performance of teenagers before licensure as measured by the Teen On-road Driving Assessment (tODA). Randomized, single-blind, clinical trial among 217 dyads (1 parent: 1 teenaged learner's-permit holder) to test TDP effectiveness on increasing the quantity and diversity of supervised practice and improving the teenagers' prelicensed driving performance. The study was conducted from December 2011 through January 2013 in Southeastern Pennsylvania. Dyads were randomized (3:2) to receive the TDP or the Pennsylvania driver's manual (control group). The TDP is a psychoeducational intervention designed to increase the quantity and diversity of parent-supervised practice. Materials are grouped by the following driving environments: empty parking lots, suburban residential streets, intermediate (1- or 2-lane) roads, highways, rural roads with curves and elevation changes, and commercial districts. The main outcomes were self-reported practice driving across 6 environments and 2 conditions and driving performance as measured by the teenagers' completion of the standardized and validated tODA 24 weeks after enrollment. Certified professional driving evaluators blinded to randomization status terminated the tODA if they determined that the teenager could not safely complete it. We examined mean differences in the quantity of supervised practice, differences in the overall proportion of teenagers in each group that had assessments terminated for unsafe driving, and the point of termination during the assessment. The TDP dyads reported more practice in 5 of the 6 environments and at night and in bad weather compared with the control dyads. Overall, 5 of 86

Toyota hybrid synergy drive

Energy Technology Data Exchange (ETDEWEB)

Gautschi, H.

2008-07-01

This presentation made at the Swiss 2008 research conference on traffic by Hannes Gautschi, director of service and training at the Toyota company in Switzerland, takes a look at Toyota's hybrid drive vehicles. The construction of the vehicles and their combined combustion engines and electric generators and drives is presented and the combined operation of these components is described. Braking and energy recovery are discussed. Figures on the performance, fuel consumption and CO{sub 2} output of the hybrid vehicles are compared with those of conventional vehicles.

RESEARCH OF DYNAMIC PARAMETERS OF THE ELECTRIC DRIVE ON THE BASIS OF ROLLING ROTOR MOTOR

Directory of Open Access Journals (Sweden)

G. V. Kulinchenko

2016-12-01

Full Text Available Purpose. Development and investigation of a dynamic model of electric drive on the base of the rolling rotor motor (RRM which reflects the positioning of the actuator of the locking and regulating equipment in time. Methodology. Analytical description of electromagnetic and mechanical processes in the electric drive during the RRM shaft movement by using a system of differential equations. Numerical imitation modeling with the processes visualization in the Matlab environment of the RRM rotor displacement with mechanical load in time. Results. It is shown that the degree of influence of the value of the load inertia on the dynamics of the object obtained by the waveform changes the rotation angle of the rotor and motor speed in time. The degree of influence of the value of the electromagnetic time constant of the dynamics of the positioning of the actuator, and the nature of transients during acceleration and fixing position of the rotor with a predetermined moment of inertia for different values of inductance. The effect of the ratio of electromechanical and electromagnetic time constants of the nature of the transition processes accompanying jog mode angular displacement of the drive shaft on the base of RRM. Originality. The lack of technical means to ensure acceptable accuracy time measurement of angular displacement shaft of the actuator in jog mode offset by using a laser meter which gives the opportunity to assess the adequacy of the dynamic model of the RRM. Practical value. The results of investigations allow to create a tool for optimization of structural, technical and hardware and software solutions for the improvement and modernization of the projected electric locking and regulating equipment. The direction for improving the dynamics of the drive on the basis of RRM is indicated providing for an increase in its torque characteristics of the motor by reducing the influence of the parameters of transients.

Optimal control of mode transition for four-wheel-drive hybrid electric vehicle with dry dual-clutch transmission

Science.gov (United States)

Zhao, Zhiguo; Lei, Dan; Chen, Jiayi; Li, Hangyu

2018-05-01

When the four-wheel-drive hybrid electric vehicle (HEV) equipped with a dry dual clutch transmission (DCT) is in the mode transition process from pure electrical rear wheel drive to front wheel drive with engine or hybrid drive, the problem of vehicle longitudinal jerk is prominent. A mode transition robust control algorithm which resists external disturbance and model parameter fluctuation has been developed, by taking full advantage of fast and accurate torque (or speed) response of three electrical power sources and getting the clutch of DCT fully involved in the mode transition process. Firstly, models of key components of driveline system have been established, and the model of five-degrees-of-freedom vehicle longitudinal dynamics has been built by using a Uni-Tire model. Next, a multistage optimal control method has been produced to realize the decision of engine torque and clutch-transmitted torque. The sliding-mode control strategy for measurable disturbance has been proposed at the stage of engine speed dragged up. Meanwhile, the double tracking control architecture that integrates the model calculating feedforward control with H∞ robust feedback control has been presented at the stage of speed synchronization. Finally, the results from Matlab/Simulink software and hardware-in-the-loop test both demonstrate that the proposed control strategy for mode transition can not only coordinate the torque among different power sources and clutch while minimizing vehicle longitudinal jerk, but also provide strong robustness to model uncertainties and external disturbance.

Association between unsafe driving performance and cognitive-perceptual dysfunction in older drivers.

Science.gov (United States)

Park, Si-Woon; Choi, Eun Seok; Lim, Mun Hee; Kim, Eun Joo; Hwang, Sung Il; Choi, Kyung-In; Yoo, Hyun-Chul; Lee, Kuem Ju; Jung, Hi-Eun

2011-03-01

To find an association between cognitive-perceptual problems of older drivers and unsafe driving performance during simulated automobile driving in a virtual environment. Cross-sectional study. A driver evaluation clinic in a rehabilitation hospital. Fifty-five drivers aged 65 years or older and 48 drivers in their late twenties to early forties. All participants underwent evaluation of cognitive-perceptual function and driving performance, and the results were compared between older and younger drivers. The association between cognitive-perceptual function and driving performance was analyzed. Cognitive-perceptual function was evaluated with the Cognitive Perceptual Assessment for Driving (CPAD), a computer-based assessment tool consisting of depth perception, sustained attention, divided attention, the Stroop test, the digit span test, field dependency, and trail-making test A and B. Driving performance was evaluated with use of a virtual reality-based driving simulator. During simulated driving, car crashes were recorded, and an occupational therapist observed unsafe performances in controlling speed, braking, steering, vehicle positioning, making lane changes, and making turns. Thirty-five older drivers did not pass the CPAD test, whereas all of the younger drivers passed the test. When using the driving simulator, a significantly greater number of older drivers experienced car crashes and demonstrated unsafe performance in controlling speed, steering, and making lane changes. CPAD results were associated with car crashes, steering, vehicle positioning, and making lane changes. Older drivers who did not pass the CPAD test are 4 times more likely to experience a car crash, 3.5 times more likely to make errors in steering, 2.8 times more likely to make errors in vehicle positioning, and 6.5 times more likely to make errors in lane changes than are drivers who passed the CPAD test. Unsafe driving performance and car crashes during simulated driving were more

Method for driving an actuator, actuator drive, and apparatus comprising an actuator

NARCIS (Netherlands)

2010-01-01

An actuator driver circuit includes a drive signal source and an electrical damping element having a negative resistance connected in series with the drive signal source. A controllable switch is provided for selectively switching the electrical damping element into or put of a signal path from a

The effects of below-elbow immobilization on driving performance.

Science.gov (United States)

Jones, Evan M; Barrow, Aaron E; Skordas, Nic J; Green, David P; Cho, Mickey S

2017-02-01

There is limited research to guide physicians and patients in deciding whether it is safe to drive while wearing various forms of upper extremity immobilization. The purpose of this study is to evaluate the effect of below-elbow removable splints and fiberglass casts on automobile driving performance. 20 healthy subjects completed 10 runs through a closed, cone-marked driving course while wearing a randomized sequence of four different types of immobilization on each extremity (short arm thumb spica fiberglass cast, short arm fiberglass cast, short arm thumb spica splint, and short arm wrist splint). The first and last driving runs were without immobilization and served as controls. Performance was measured based on evaluation by a certified driving instructor (pass/fail scoring), cones hit, run time, and subject-perceived driving difficulty (1-10 analogue scoring). The greatest number of instructor-scored failures occurred while immobilized in right arm spica casts (n=6; p=0.02) and left arm spica casts (n=5; p=0.049). The right arm spica cast had the highest subject-perceived difficulty (5.2±1.9; pimmobilization had significantly increased perceived difficulty compared to control, except for the left short arm splint (2.5±1.6; p>0.05). There was no significant difference in number of cones hit or driving time between control runs and runs with any type of immobilization. Drivers should use caution when wearing any of the forms of upper extremity immobilization tested in this study. All forms of immobilization, with exception of the left short arm splint significantly increased perceived driving difficulty. However, only the fiberglass spica casts (both left and right arm), significantly increased drive run failures due to loss of vehicle control. We recommend against driving when wearing a below-elbow fiberglass spica cast on either extremity. Copyright © 2016. Published by Elsevier Ltd.

Climate Control Load Reduction Strategies for Electric Drive Vehicles in Cold Weather: Preprint

Energy Technology Data Exchange (ETDEWEB)

Jeffers, Matthew; Chaney, Lawrence; Rugh, John

2016-03-31

When operated, the climate control system is the largest auxiliary load on a vehicle. This load has significant impact on fuel economy for conventional and hybrid vehicles, and it drastically reduces the driving range of all electric vehicles (EVs). Heating is even more detrimental to EV range than cooling because no engine waste heat is available. Reducing the thermal loads on the heating, ventilating, and air conditioning system will extend driving range and increase the market penetration of EVs. Researchers at the National Renewable Energy Laboratory have evaluated strategies for vehicle climate control load reduction with special attention toward grid connected electric vehicles. Outdoor vehicle thermal testing and computational modeling were used to assess potential strategies for improved thermal management and to evaluate the effectiveness of thermal load reduction technologies. A human physiology model was also used to evaluate the impact on occupant thermal comfort. Experimental evaluations of zonal heating strategies demonstrated a 5.5% to 28.5% reduction in cabin heating energy over a 20-minute warm-up. Vehicle simulations over various drive cycles show a 6.9% to 18.7% improvement in EV range over baseline heating using the most promising zonal heating strategy investigated. A national-level analysis was conducted to determine the overall national impact. If all vehicles used the best zonal strategy, the range would be improved by 7.1% over the baseline heating range. This is a 33% reduction in the range penalty for heating.

New Materials for Electric Drive Vehicles - Final CRADA Report

Energy Technology Data Exchange (ETDEWEB)

Carter, J. David [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-10-18

This project was sponsored by the US DOE Global Initiatives for Proliferation Prevention. The object was for Ukrainian and US partners, including Argonne, AETC, and Dontech to develop special carbon materials and factory production equipment with the goal of making better car batteries to achieve DOE's goals for all-electric and plug-in hybrid electric vehicles. Carbon materials are used in designs for lithium-ion batteries and metal-air batteries, both leading contenders for future electric cars. Specifically, the collaborators planned to use the equipment derived from this project to develop a rechargeable battery system that will use the carbon materials produced by the innovative factory process equipment. The final outcome of the project was that the Ukrainian participants consisting of the Kharkov Institute of Physics and Technology (KIPT), the Institute of Gas of National Academy of Sciences of Ukraine and the Materials Research Center, Ltd. designed, built, tested and delivered 14 pieces of processing equipment for pilot scale carbon production lines at the AETC, Arlington Heights facilities. The pilot scale equipment will be used to process materials such as activated carbon, thermally expanded graphite and carbon coated nano-particles. The equipment was shipped from Ukraine to the United States and received by AETC on December 3, 2013. The equipment is on loan from Argonne, control # 6140. Plug-in hybrid electric vehicles (PHEV) and all-electric vehicles have already demostrated success in the U.S. as they begin to share the market with older hybrid electric designs. When the project was conceived, PHEV battery systems provided a ~40 mile driving range (2011 figures). DOE R&D targets increased this to >100 miles at reduced cost less than $250/kWh (2011 figures.) A 2016 Tesla model S has boasted 270 miles. The project object was to develop pilot-production line equipment for advanced hybrid battery system that achieves cycle life of 1000, an energy

A novel multi-drive electric vehicle system control based on multi-input multi-output PID controller

Directory of Open Access Journals (Sweden)

Gasbaoui Brahim

2012-01-01

Full Text Available In-wheel-motor drive electric vehicle (EV is an innovative configuration of the modern EV, in which each wheel is driven individually by an electric motor. The classical traction motor control called the Independent Machine Control Structure (IMCS using a PID speed controller presents major inconveniences in modern EV safety, when the proposed control can not ensure stability of the EV with differing road topology and variations of speed. A new approach is proposed for a control of a two-in-wheel-motor drive EV, called the Maximum Control Structure MCS. This is based on a multivariable PID (MIMO-PID strategy, which is employed to estimate the linear speed error of each of the two back driving wheels, when the error of each wheel is taken into account in the other speed control computations. Simulation results show that the new control system presents increased safety for the EVs compared with the IMCS strategy and can maintain the error slip rate within the optimal range, ensuring the stability of the vehicle either in a straight or a curved line.

MEMS vibrating-beam accelerometer with piezoelectric drive

Science.gov (United States)

Strehlow, John; MacGugan, Doug

2017-09-12

A high-temperature drive component for a double-ended tuning fork (DETF). The drive component attaches to a surface of at least one of the tines. The drive component includes at least one piezoelectric trace sandwiched at least partially between two electrical traces. At least one of the tines includes a doped silicon base with drive component located thereon. One of the electrical traces is electrically connected to the doped silicon base and the other is electrically isolated from the doped silicon base.

Lower hybrid current drive in the presence of electric field

Directory of Open Access Journals (Sweden)

Saveliev Alexander

2017-01-01

Full Text Available A new one-dimensional approach to the lower hybrid current drive (LHCD modelling in the presence of an inductive electric field is suggested in this paper. The approach is based on using time-dependent solutions of a well-known Fokker-Planck equation for the distribution function of fast electrons calculated concurrently with solving plasma transport equation in the Automated System for TRansport Analysis (ASTRA [1]. A good agreement between experimental and modelling results is demonstrated for an FT-2 [2] plasma shot. Also new formulae for the steady-state solution of this kinetic equation are found.

Thyristor voltage converter in induction electric drives with microprocessor control

Energy Technology Data Exchange (ETDEWEB)

Braslavsky, I.; Zuzev, A.; Shilin, S. [Electric Drive Department, Urals State Technical University, Ekaterinburg (Russian Federation)

1997-12-31

The paper consists of some results on developed pulse model of thyristor voltage converter which is one of the most mathematically complicated unit of electric drive. The model structure and model parameter calculating method are represented. The application of the model allows to analyse stability in `locally` by the linear pulse system theory methods with talking into consideration quantise processes within the converter. Such application provides the obtaining higher accurate results comparing with the non-linear system theory approximate methods. Logarithmic frequency characteristics are used to analyse converter dynamic features and they are represented too. (orig.) 4 refs.

Lower hybrid current drive in the presence of electric field

Science.gov (United States)

Saveliev, Alexander; Zakharov, Vladimir

2017-10-01

A new one-dimensional approach to the lower hybrid current drive (LHCD) modelling in the presence of an inductive electric field is suggested in this paper. The approach is based on using time-dependent solutions of a well-known Fokker-Planck equation for the distribution function of fast electrons calculated concurrently with solving plasma transport equation in the Automated System for TRansport Analysis (ASTRA) [1]. A good agreement between experimental and modelling results is demonstrated for an FT-2 [2] plasma shot. Also new formulae for the steady-state solution of this kinetic equation are found.

Efficient Driving of Piezoelectric Transducers Using a Biaxial Driving Technique.

Directory of Open Access Journals (Sweden)

Samuel Pichardo

Full Text Available Efficient driving of piezoelectric materials is desirable when operating transducers for biomedical applications such as high intensity focused ultrasound (HIFU or ultrasound imaging. More efficient operation reduces the electric power required to produce the desired bioeffect or contrast. Our preliminary work [Cole et al. Journal of Physics: Condensed Matter. 2014;26(13:135901.] suggested that driving transducers by applying orthogonal electric fields can significantly reduce the coercivity that opposes ferroelectric switching. We present here the experimental validation of this biaxial driving technique using piezoelectric ceramics typically used in HIFU. A set of narrow-band transducers was fabricated with two sets of electrodes placed in an orthogonal configuration (following the propagation and the lateral mode. The geometry of the ceramic was chosen to have a resonance frequency similar for the propagation and the lateral mode. The average (± s.d. resonance frequency of the samples was 465.1 (± 1.5 kHz. Experiments were conducted in which each pair of electrodes was driven independently and measurements of effective acoustic power were obtained using the radiation force method. The efficiency (acoustic/electric power of the biaxial driving method was compared to the results obtained when driving the ceramic using electrodes placed only in the pole direction. Our results indicate that the biaxial method increases efficiency from 50% to 125% relative to the using a single electric field.

Simultaneous electrical and mechanical resonance drive for large signal amplification of micro resonators

KAUST Repository

Hasan, M. H.

2018-01-12

Achieving large signal-noise ratio using low levels of excitation signal is key requirement for practical applications of micro and nano electromechanical resonators. In this work, we introduce the double electromechanical resonance drive concept to achieve an order-of-magnitude dynamic signal amplification in micro resonators. The concept relies on simultaneously activating the micro-resonator mechanical and electrical resonance frequencies. We report an input voltage amplification up to 15 times for a micro-resonator when its electrical resonance is tuned to match the mechanical resonance that leads to dynamic signal amplification in air (Quality factor enhancement). Furthermore, using a multi-frequency excitation technique, input voltage and vibrational amplification of up to 30 times were shown for the same micro-resonator while relaxing the need to match its mechanical and electrical resonances.

Simultaneous electrical and mechanical resonance drive for large signal amplification of micro resonators

KAUST Repository

Hasan, M. H.; Alsaleem, F. M.; Jaber, Nizar; Hafiz, Md Abdullah Al; Younis, Mohammad I.

2018-01-01

Achieving large signal-noise ratio using low levels of excitation signal is key requirement for practical applications of micro and nano electromechanical resonators. In this work, we introduce the double electromechanical resonance drive concept to achieve an order-of-magnitude dynamic signal amplification in micro resonators. The concept relies on simultaneously activating the micro-resonator mechanical and electrical resonance frequencies. We report an input voltage amplification up to 15 times for a micro-resonator when its electrical resonance is tuned to match the mechanical resonance that leads to dynamic signal amplification in air (Quality factor enhancement). Furthermore, using a multi-frequency excitation technique, input voltage and vibrational amplification of up to 30 times were shown for the same micro-resonator while relaxing the need to match its mechanical and electrical resonances.

An Investigation on the Effect of Driver Style and Driving Events on Energy Demand of a PHEV

OpenAIRE

Rajan, Brahmadevan; McGordon, Andrew; Jennings, Paul

2012-01-01

Environmental concerns, security of fuel supply and CO2 regulations are driving innovation in the automotive industry towards electric and hybrid electric vehicles. The fuel economy and emission performance of hybrid electric vehicles (HEVs) strongly depends on the energy management system (EMS). Prior knowledge of driving information could be used to enhance the performance of a HEV. However, how the necessary information can be obtained to use in EMS optimisation still remains a challenge. ...

THE EFFECT OF CELLULAR PHONE USE ON DRIVING PERFORMANCE

Directory of Open Access Journals (Sweden)

Toshiro ISHIDA

2001-01-01

In this experiment, it was confirmed that use of a hands-free set is effective to some extent, but driving performance was poorer than with driving only. Even though different forms of in-vehicle information apparatus were used, a delay in information processing was consistently found.

Assessment of needs and research roadmaps for rechargeable energy storage system (RESS) onboard electric drive buses

Science.gov (United States)

2010-12-01

In support of the Federal Transit Administration (FTA) Electric Drive Strategic Plan (EDSP), this report assesses state-of-art advances in lithium-ion batteries, ultracapacitors, and related power management and control technologies for the rechargea...

Study of the Effects of Alcohol on Drivers and Driving Performance on Straight Road

Directory of Open Access Journals (Sweden)

Xiaohua Zhao

2014-01-01

Full Text Available Drinking driving is responsible for a high proportion of traffic accidents. To study the effects of alcohol on drivers and driving performance, 25 drivers’ subjective feelings and driving performance data in different blood-alcohol concentration (BAC levels were collected with simulated driving experiment. The investigation results revealed that alcohol affected drivers in many aspects, including attitude, judgment, vigilance, perception, reaction, and controlling. The analysis of accident rate showed that higher BAC level would lead to higher accident rate. The statistical analysis results of driving performance indicated that average speed, speed standard deviation, and lane position standard deviation were significantly higher under the influence of alcohol. They also had a statistically significant linear trend as the function of BAC level. The discrimination of drinking driving based on driving performance was performed with Fisher discrimination method. The results showed that drinking driving with higher BAC level was easier to discriminate from normal driving. Also, the results indicated that the three significant indicators on straight roadway could be used in the discrimination of drinking driving state. The conclusions can provide references for the study of drinking driving and the identification of driving state and then contribute to traffic safety.

Energy Management Strategy for Hybrid Electric Vehicle Based on Driving Condition Identification Using KGA-Means

Directory of Open Access Journals (Sweden)

Shuxian Li

2018-06-01

Full Text Available In order to solve the problem related to adaptive energy management strategies based on driving condition identification being difficult to be applied to a real hybrid electric vehicle (HEV controller, this paper proposes an energy management strategy by combining the driving condition identification algorithm based on genetic optimized K-means clustering algorithm (KGA-means, and the equivalent consumption minimization strategy (ECMS. The simulation results show that compared with ECMS, the energy management strategy proposed in this article drives the engine working point closer to the best efficiency curve, and smooths out the state of charge (SOC change and better maintains the SOC in a highly efficient area. As a result, the vehicle fuel consumption reduces by 6.84%.

Driving While Interacting With Google Glass: Investigating the Combined Effect of Head-Up Display and Hands-Free Input on Driving Safety and Multitask Performance.

Science.gov (United States)

Tippey, Kathryn G; Sivaraj, Elayaraj; Ferris, Thomas K

2017-06-01

This study evaluated the individual and combined effects of voice (vs. manual) input and head-up (vs. head-down) display in a driving and device interaction task. Advances in wearable technology offer new possibilities for in-vehicle interaction but also present new challenges for managing driver attention and regulating device usage in vehicles. This research investigated how driving performance is affected by interface characteristics of devices used for concurrent secondary tasks. A positive impact on driving performance was expected when devices included voice-to-text functionality (reducing demand for visual and manual resources) and a head-up display (HUD) (supporting greater visibility of the driving environment). Driver behavior and performance was compared in a texting-while-driving task set during a driving simulation. The texting task was completed with and without voice-to-text using a smartphone and with voice-to-text using Google Glass's HUD. Driving task performance degraded with the addition of the secondary texting task. However, voice-to-text input supported relatively better performance in both driving and texting tasks compared to using manual entry. HUD functionality further improved driving performance compared to conditions using a smartphone and often was not significantly worse than performance without the texting task. This study suggests that despite the performance costs of texting-while-driving, voice input methods improve performance over manual entry, and head-up displays may further extend those performance benefits. This study can inform designers and potential users of wearable technologies as well as policymakers tasked with regulating the use of these technologies while driving.

Estimating Driving Performance Based on EEG Spectrum Analysis

Directory of Open Access Journals (Sweden)

Jung Tzyy-Ping

2005-01-01

Full Text Available The growing number of traffic accidents in recent years has become a serious concern to society. Accidents caused by driver's drowsiness behind the steering wheel have a high fatality rate because of the marked decline in the driver's abilities of perception, recognition, and vehicle control abilities while sleepy. Preventing such accidents caused by drowsiness is highly desirable but requires techniques for continuously detecting, estimating, and predicting the level of alertness of drivers and delivering effective feedbacks to maintain their maximum performance. This paper proposes an EEG-based drowsiness estimation system that combines electroencephalogram (EEG log subband power spectrum, correlation analysis, principal component analysis, and linear regression models to indirectly estimate driver's drowsiness level in a virtual-reality-based driving simulator. Our results demonstrated that it is feasible to accurately estimate quantitatively driving performance, expressed as deviation between the center of the vehicle and the center of the cruising lane, in a realistic driving simulator.

Characterizing on-road driving performance in individuals with traumatic brain injury who pass or fail an on-road driving assessment.

Science.gov (United States)

Stolwyk, Renerus J; Charlton, Judith L; Ross, Pamela E; Bédard, Michel; Marshall, Shawn; Gagnon, Sylvain; Gooden, James R; Ponsford, Jennie L

2018-01-15

To characterise on-road driving performance in individuals with traumatic brain injury who fail on-road driving assessment, compared with both those who pass assessment and healthy controls, and the injury and cognitive factors associated with driving performance. Cross-sectional. Forty eight participants with traumatic brain injury (Age M = 40.50 SD = 14.62, 77% male, post-traumatic amnesia days M = 28.74 SD =27.68) and 48 healthy matched controls completed a standardised on-road driving assessment in addition to cognitive measures. Individuals with traumatic brain injury who passed on-road driving assessment performed no differently from controls while individuals with traumatic brain injury who failed the assessment demonstrated significantly worse driving performance relative to controls across a range of driving manoeuvres and error types including observation of on-road environment, speed control, gap selection, lane position, following distance and basic car control. Longer time post-injury and reduced visual perception were both significantly correlated with reduced driving skills. This exploratory study indicated that drivers with traumatic brain injury who failed on-road assessment demonstrated a heterogeneous pattern of impaired driving manoeuvres, characterised by skill deficits across both operational (e.g., basic car control and lane position) and tactical domains (e.g., following distance, gap selection, and observation) of driving. These preliminary findings can be used for implementation of future driving assessments and rehabilitation programs. Implications for rehabilitation Clinicians should be aware that the majority of individuals with traumatic brain injury were deemed fit to resume driving following formal on-road assessment, despite having moderate to very severe traumatic brain injuries. Drivers with traumatic brain injury who failed an on-road assessment demonstrated a heterogeneous pattern of impaired skills including errors

Comparison of driving simulator performance and neuropsychological testing in narcolepsy.

Science.gov (United States)

Kotterba, Sylvia; Mueller, Nicole; Leidag, Markus; Widdig, Walter; Rasche, Kurt; Malin, Jean-Pierre; Schultze-Werninghaus, Gerhard; Orth, Maritta

2004-09-01

Daytime sleepiness and cataplexy can increase automobile accident rates in narcolepsy. Several countries have produced guidelines for issuing a driving license. The aim of the study was to compare driving simulator performance and neuropsychological test results in narcolepsy in order to evaluate their predictive value regarding driving ability. Thirteen patients with narcolepsy (age: 41.5+/-12.9 years) and 10 healthy control patients (age: 55.1+/-7.8 years) were investigated. By computer-assisted neuropsychological testing, vigilance, alertness and divided attention were assessed. In a driving simulator patients and controls had to drive on a highway for 60 min (mean speed of 100 km/h). Different weather and daytime conditions and obstacles were presented. Epworth Sleepiness Scale-Scores were significantly raised (narcolepsy patients: 16.7+/-5.1, controls: 6.6+/-3.6, P divided attention (56.9+/-25.4) and vigilance (58.7+/-26.8) were in a normal range. There was, however, a high inter-individual difference. There was no correlation between driving performance and neuropsychological test results or ESS Score. Neuropsychological test results did not significantly change in the follow-up. The difficulties encountered by the narcolepsy patient in remaining alert may account for sleep-related motor vehicle accidents. Driving simulator investigations are closely related to real traffic situations than isolated neuropsychological tests. At the present time the driving simulator seems to be a useful instrument judging driving ability especially in cases with ambiguous neuropsychological results.

An investigation on the effect of driver style and driving\\ud events on energy demand of a PHEV

OpenAIRE

Padmarajan, Brahmadevan V.; McGordon, Andrew; Jennings, P. A. (Paul A.)

2012-01-01

Environmental concerns, security of fuel supply and CO2 regulations are driving innovation in the automotive industry towards electric and hybrid electric vehicles. The fuel economy and emission performance of hybrid electric vehicles (HEVs) strongly depends on the energy management system (EMS). Prior knowledge of driving information could be used to enhance the performance of a HEV. However, how the necessary information can be obtained to use in EMS optimisation still remains a challenge. ...

Characterization of In-Use Medium Duty Electric Vehicle Driving and Charging Behavior: Preprint

Energy Technology Data Exchange (ETDEWEB)

Duran, A.; Ragatz, A.; Prohaska, R.; Kelly, K.; Walkowicz, K.

2014-11-01

The U.S. Department of Energy's American Recovery and Reinvestment Act (ARRA) deployment and demonstration projects are helping to commercialize technologies for all-electric vehicles (EVs). Under the ARRA program, data from Smith Electric and Navistar medium duty EVs have been collected, compiled, and analyzed in an effort to quantify the impacts of these new technologies. Over a period of three years, the National Renewable Energy Laboratory (NREL) has compiled data from over 250 Smith Newton EVs for a total of over 100,000 days of in-use operation. Similarly, data have been collected from over 100 Navistar eStar vehicles, with over 15,000 operating days having been analyzed. NREL has analyzed a combined total of over 4 million kilometers of driving and 1 million hours of charging data for commercial operating medium duty EVs. In this paper, the authors present an overview of medium duty EV operating and charging behavior based on in-use data collected from both Smith and Navistar vehicles operating in the United States. Specifically, this paper provides an introduction to the specifications and configurations of the vehicles examined; discusses the approach and methodology of data collection and analysis, and presents detailed results regarding daily driving and charging behavior. In addition, trends observed over the course of multiple years of data collection are examined, and conclusions are drawn about early deployment behavior and ongoing adjustments due to new and improving technology. Results and metrics such as average daily driving distance, route aggressiveness, charging frequency, and liter per kilometer diesel equivalent fuel consumption are documented and discussed.

Effects of Cognitive Load on Driving Performance: The Cognitive Control Hypothesis.

Science.gov (United States)

Engström, Johan; Markkula, Gustav; Victor, Trent; Merat, Natasha

2017-08-01

The objective of this paper was to outline an explanatory framework for understanding effects of cognitive load on driving performance and to review the existing experimental literature in the light of this framework. Although there is general consensus that taking the eyes off the forward roadway significantly impairs most aspects of driving, the effects of primarily cognitively loading tasks on driving performance are not well understood. Based on existing models of driver attention, an explanatory framework was outlined. This framework can be summarized in terms of the cognitive control hypothesis: Cognitive load selectively impairs driving subtasks that rely on cognitive control but leaves automatic performance unaffected. An extensive literature review was conducted wherein existing results were reinterpreted based on the proposed framework. It was demonstrated that the general pattern of experimental results reported in the literature aligns well with the cognitive control hypothesis and that several apparent discrepancies between studies can be reconciled based on the proposed framework. More specifically, performance on nonpracticed or inherently variable tasks, relying on cognitive control, is consistently impaired by cognitive load, whereas the performance on automatized (well-practiced and consistently mapped) tasks is unaffected and sometimes even improved. Effects of cognitive load on driving are strongly selective and task dependent. The present results have important implications for the generalization of results obtained from experimental studies to real-world driving. The proposed framework can also serve to guide future research on the potential causal role of cognitive load in real-world crashes.

Electric terminal performance and characterization of solid oxide fuel cells and systems

Science.gov (United States)

Lindahl, Peter Allan

Solid Oxide Fuel Cells (SOFCs) are electrochemical devices which can effect efficient, clean, and quiet conversion of chemical to electrical energy. In contrast to conventional electricity generation systems which feature multiple discrete energy conversion processes, SOFCs are direct energy conversion devices. That is, they feature a fully integrated chemical to electrical energy conversion process where the electric load demanded of the cell intrinsically drives the electrochemical reactions and associated processes internal to the cell. As a result, the cell's electric terminals provide a path for interaction between load side electric demand and the conversion side processes. The implication of this is twofold. First, the magnitude and dynamic characteristics of the electric load demanded of the cell can directly impact the long-term efficacy of the cell's chemical to electrical energy conversion. Second, the electric terminal response to dynamic loads can be exploited for monitoring the cell's conversion side processes and used in diagnostic analysis and degradation-mitigating control schemes. This dissertation presents a multi-tier investigation into this electric terminal based performance characterization of SOFCs through the development of novel test systems, analysis techniques and control schemes. First, a reference-based simulation system is introduced. This system scales up the electric terminal performance of a prototype SOFC system, e.g. a single fuel cell, to that of a full power-level stack. This allows realistic stack/load interaction studies while maintaining explicit ability for post-test analysis of the prototype system. Next, a time-domain least squares fitting method for electrochemical impedance spectroscopy (EIS) is developed for reduced-time monitoring of the electrochemical and physicochemical mechanics of the fuel cell through its electric terminals. The utility of the reference-based simulator and the EIS technique are demonstrated

Harnessing big data for estimating the energy consumption and driving range of electric vehicles

DEFF Research Database (Denmark)

Fetene, Gebeyehu Manie; Kaplan, Sigal; Mabit, Stefan Lindhard

2017-01-01

type; (iv) weather conditions. The results of the analysis measure the mean ECR of BEVs at 0.183 kW h/km, underline a 34% increase in ECR and a 25% decrease in driving range in the winter with respect to the summer, and suggest the electricity tariff for BEVs to be cost efficient with respect...

Comparative analysis of energy economy among different types of electric motor driving; Analise comparativa de economia de energia entre diferentes tipos de acionamento de motores electricos

Energy Technology Data Exchange (ETDEWEB)

Silva, Marcelo Santos da; Oliveira, Carlos Henrique, e-mails: mcelo_sant@ig.com.br; caique1979@yahoo.com.br; Albuquerque, Carlos Jesivan Marques; Fortes, Marcio Zamboti [Universidade Severino Sombra (USS), Vassouras, RJ (Brazil)], e-mails: cjesivan@uss.br; mzamboti@uss.br

2008-07-01

The application of controlled drives loads of small power can cause undesirable disturbances for electrical installations, but it brings some benefits when comparing the energy consumption that this application has on its regular period of operation. This study analyses using comparatives, the electrical economy using the different types of drives for three phase electric induction motors of low voltage. Running up tests on the test bench didactic, the inverter drives, soft starter and contactor switch were analyzed for different loads (motor without load, 50% and 100% load), rating in S1 and S4. (author)

Motor Torque Calculations For Electric Vehicle

Directory of Open Access Journals (Sweden)

Saurabh Chauhan

2015-08-01

Full Text Available Abstract It is estimated that 25 of the total cars across the world will run on electricity by 2025. An important component that is an integral part of all electric vehicles is the motor. The amount of torque that the driving motor delivers is what plays a decisive role in determining the speed acceleration and performance of an electric vehicle. The following work aims at simplifying the calculations required to decide the capacity of the motor that should be used to drive a vehicle of particular specifications.

Associations Between Driving Performance and Engaging in Secondary Tasks: A Systematic Review

Science.gov (United States)

Ferdinand, Alva O.

2014-01-01

We conducted a systematic review and meta-analysis of the literature examining the relationship between driving performance and engaging in secondary tasks. We extracted data from abstracts of 206 empirical articles published between 1968 and 2012 and developed a logistic regression model to identify correlates of a detrimental relationship between secondary tasks and driving performance. Of 350 analyses, 80% reported finding a detrimental relationship. Studies using experimental designs were 37% less likely to report a detrimental relationship (P = .014). Studies examining mobile phone use while driving were 16% more likely to find such a relationship (P = .009). Quasi-experiments can better determine the effects of secondary tasks on driving performance and consequently serve to inform policymakers interested in reducing distracted driving and increasing roadway safety. PMID:24432925

GROUNDING THE REDUCTION OF POWER OF THE HYDRAULIC DRIVE ELECTRIC MOTOR BY EQUIVALENT POWER METHOD

Directory of Open Access Journals (Sweden)

O. Hrygorov

2017-06-01

Full Text Available The authors have analyzed the power consumption by a hydraulic drive and wound rotor motor of crane mechanisms at all stages of the operational cycle: acceleration, movement at nominal or intermediate speed and deceleration. The decrease of the rated capacity of electric motors is justified.

Performance of a direct drive hydro turbine for wave power generation

Energy Technology Data Exchange (ETDEWEB)

Lee, Y-H; Kim, C-G [Division of Mechanical and Information Engineering, Korea Maritime University Dongsam-dong 1, Youngdo-ku, Busan, 606-791 (Korea, Republic of); Choi, Y-D; Kim, I-S [Department of Mechanical Engineering, Mokpo National University Muan-ro 560, Chunggye-myun, Jeonnam, 534-729 (Korea, Republic of); Hwang, Y-C, E-mail: lyh@hhu.ac.k [R and D Institute, Shinhan Precision Co. Ltd. Gomo-ri 313, Jinle-myun, Kimhae, 621-881 (Korea, Republic of)

2010-08-15

Clean and renewable energy technologies using ocean energy give us non-polluting alternatives to fossil-fueled power plants as a countermeasure against the global warming and growing demand for electrical energy. Among the ocean energy resources, wave power takes a growing interest because of its enormous amount of potential energy in the world. Therefore, various types of wave power system to capture the energy of ocean waves have been developed. However, suitable turbine type is not normalized yet because of relatively low efficiency of the turbine systems. The purpose of this study is to investigate the performance of a newly developed direct drive hydro turbine (DDT), which will be built in a caisson for wave power plant. Experiment and CFD analysis are conducted to clarify the turbine performance and internal flow characteristics. The results show that the DDT obtains fairly good turbine efficiency in both cases of with wave and no wave conditions. As the turbine performance is influenced considerably by the wave condition, designed point of the turbine should be determined according to the wave condition at an expected installation site. Most of the output power generates at the runner passage of the Stage 2.

Sensorless FOC Performance Improved with On-Line Speed and Rotor Resistance Estimator Based on an Artificial Neural Network for an Induction Motor Drive

Directory of Open Access Journals (Sweden)

Jose. M. Gutierrez-Villalobos

2015-06-01

Full Text Available Three-phase induction motor drive requires high accuracy in high performance processes in industrial applications. Field oriented control, which is one of the most employed control schemes for induction motors, bases its function on the electrical parameter estimation coming from the motor. These parameters make an electrical machine driver work improperly, since these electrical parameter values change at low speeds, temperature changes, and especially with load and duty changes. The focus of this paper is the real-time and on-line electrical parameters with a CMAC-ADALINE block added in the standard FOC scheme to improve the IM driver performance and endure the driver and the induction motor lifetime. Two kinds of neural network structures are used; one to estimate rotor speed and the other one to estimate rotor resistance of an induction motor.

Development of a multi-mode hybrid electric bus

Energy Technology Data Exchange (ETDEWEB)

Shemmans, M.J. [Overland Custom Coach, Thorndale, ON (Canada); Bland, C. [BET Services Inc., Mississauga, ON (Canada)

2004-04-01

This paper describes the development of an energy efficient, low floor, 28 foot hybrid electric bus for use as an airport shuttle bus or other specialized transit operations. A multi-mode concept was also adopted to include the capability of operating in battery-only drive, engine-only drive or a range of hybrid electric drive modes. The electric drivetrain was powered by a battery pack or a combination of a battery pack and an internal combustion engine-powered electric generator. The participating companies in this project include Overland Custom Coach, BET Services Inc., Siemens and Transport Canada. The technical feasibility study was described with reference to duty cycles, performance issues, vehicle weight, mechanical drive issues, brakes, suspension, powertrain cooling, heating, ventilation, electrical system, batteries and control system. The commercial feasibility was also described in terms of capital and operating costs. Results of the prototype tests validate the possibilities of zero or reduced emission transit in real world applications. 25 tabs., 32 figs.

On-road magnetic emissions prediction of electric cars in terms of driving dynamics using neural networks

NARCIS (Netherlands)

Wefky, Ahmed M.; Espinosa, Felipe; Leferink, Frank Bernardus Johannes; Gardel, Alfredo; Vogt-Ardatjew, R.A.

2013-01-01

This paper presents a novel artificial neural network (ANN) model estimating vehicle-level radiated magnetic emissions of an electric car as a function of the corresponding driving pattern. Real world electromagnetic interference (EMI) experiments have been realized in a semi-anechoic chamber using

Hybrid and Electric Advanced Vehicle Systems Simulation

Science.gov (United States)

Beach, R. F.; Hammond, R. A.; Mcgehee, R. K.

1985-01-01

Predefined components connected to represent wide variety of propulsion systems. Hybrid and Electric Advanced Vehicle System (HEAVY) computer program is flexible tool for evaluating performance and cost of electric and hybrid vehicle propulsion systems. Allows designer to quickly, conveniently, and economically predict performance of proposed drive train.

Driving performance in persons with mild to moderate symptoms of multiple sclerosis.

Science.gov (United States)

Devos, Hannes; Brijs, Tom; Alders, Geert; Wets, Geert; Feys, Peter

2013-08-01

To investigate whether driving performance is impaired in persons with mild to moderate multiple sclerosis (MS). This study included 15 persons with MS (pwMS) and 17 healthy controls. The MS group exhibited mild to moderate impairments on the Expanded Disability Status Scale (median, Q1-Q3; 3.5, 2.5-4). The driving simulation required participants to drive in daily traffic while attending to a divided attention (DA) task. Computerized measures on the driving task included number of accidents, tickets, speed maintenance, standard deviation of lateral position, and time to collision. Response times and accuracy on the DA task were also computer generated. Additionally, pwMS completed a clinical evaluation encompassing motor, functional, visual, psychosocial and cognitive tests. No differences between healthy controls and pwMS were observed on all measures of the primary driving task. PwMS performed worse than healthy controls on DA response time (3.10 s, 2.87-3.68 versus 2.15 s, 2.04-2.43; p = 0.001) and accuracy (15 correct answers, 11-18 versus 24 correct answers, 22-25; p driving task above the DA task. The relationship between depression and driving performance in MS merits further investigation.

Driving Interface Based on Tactile Sensors for Electric Wheelchairs or Trolleys

Directory of Open Access Journals (Sweden)

Andrés Trujillo-León

2014-02-01

Full Text Available This paper introduces a novel device based on a tactile interface to replace the attendant joystick in electric wheelchairs. It can also be used in other vehicles such as shopping trolleys. Its use allows intuitive driving that requires little or no training, so its usability is high. This is achieved by a tactile sensor located on the handlebar of the chair or trolley and the processing of the information provided by it. When the user interacts with the handle of the chair or trolley, he or she exerts a pressure pattern that depends on the intention to accelerate, brake or turn to the left or right. The electronics within the device then perform the signal conditioning and processing of the information received, identifying the intention of the user on the basis of this pattern using an algorithm, and translating it into control signals for the control module of the wheelchair. These signals are equivalent to those provided by a joystick. This proposal aims to help disabled people and their attendees and prolong the personal autonomy in a context of aging populations.

A thermodynamic approach to compare the performance of rhombic-drive and crank-drive mechanisms for a beta-type Stirling engine

International Nuclear Information System (INIS)

Aksoy, F.; Solmaz, H.; Karabulut, H.; Cinar, C.; Ozgoren, Y.O.; Polat, Seyfi

2016-01-01

Highlights: • Rhombic drive and crank drive mechanisms of a beta type engine were compared. • Nodal analysis method was used to compare engines having different drive mechanism. • Maximum specific power was 1410 W/L for rhombic-drive engine. • Heat transfer coefficient was determined as 475 W/m"2K for rhombic-drive engine. • Rhombic drive provided higher efficiency because of its better kinematic behaviours. - Abstract: In this study, the effect of rhombic drive and crank drive mechanisms on the performance of a beta-type Stirling engine was investigated by nodal analysis. Kinematic and thermodynamic relations for both drive mechanisms were introduced and a Fortran code was written for the solution. Piston strokes, cylinder and displacer diameters, hot and cold end temperatures, regenerator volumes and heat transfer surface areas were taken equal for both engines with two different drive mechanisms. In the analysis, air was used as the working gas. Engine power and efficiency were compared for different charge pressure values, working gas mass values, heat transfer coefficients and hot end temperatures. Maximum specific engine power was 1410 W/L for the engine with rhombic drive mechanism and 1200 W/L for the engine with crank drive mechanism at 4 bars of charge pressure and 500 W/m"2K heat transfer coefficient. Rhombic drive mechanism was relatively advantageous at low working gas mass values and high hot end temperatures. In comparison with the engine having rhombic drive mechanism, the relatively poor kinematic behaviour of the engine having crank drive mechanism caused lower engine efficiency and performance. Heat transfer coefficient was also predicted by using an experimental pressure trace.

Exploring the association between working memory and driving performance in Parkinson's disease.

Science.gov (United States)

Vardaki, Sophia; Devos, Hannes; Beratis, Ion; Yannis, George; Papageorgiou, Sokratis G

2016-05-18

The aim of this study was to explore whether varying levels of operational and tactical driving task demand differentially affect drivers with Parkinson's disease (PD) and control drivers in their sign recall. Study participants aged between 50 and 70 years included a group of drivers with PD (n = 10) and a group of age- and sex-matched control drivers (n = 10). Their performance in a sign recall task was measured using a driving simulator. Drivers in the control group performed better than drivers with PD in a sign recall task, but this trend was not statistically significant (P =.43). In addition, regardless of group membership, subjects' performance differed according to varying levels of task demand. Performance in the sign recall task was more likely to drop with increasing task demand (P =.03). This difference was significant when the variation in task demand was associated with a cognitive task; that is, when drivers were required to apply the instructions from working memory. Although the conclusions drawn from this study are tentative, the evidence presented here is encouraging with regard to the use of a driving simulator to examine isolated cognitive functions underlying driving performance in PD. With an understanding of its limitations, such driving simulation in combination with functional assessment batteries measuring physical, visual, and cognitive abilities could comprise one component of a multitiered system to evaluate medical fitness to drive.

Progress of the Computer-Aided Engineering of Electric Drive Vehicle Batteries (CAEBAT) (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Pesaran, A. A.; Han, T.; Hartridge, S.; Shaffer, C.; Kim, G. H.; Pannala, S.

2013-06-01

This presentation, Progress of Computer-Aided Engineering of Electric Drive Vehicle Batteries (CAEBAT) is about simulation and computer-aided engineering (CAE) tools that are widely used to speed up the research and development cycle and reduce the number of build-and-break steps, particularly in the automotive industry. Realizing this, DOE?s Vehicle Technologies Program initiated the CAEBAT project in April 2010 to develop a suite of software tools for designing batteries.

Alcohol consumption for simulated driving performance: A systematic review.

Science.gov (United States)

Rezaee-Zavareh, Mohammad Saeid; Salamati, Payman; Ramezani-Binabaj, Mahdi; Saeidnejad, Mina; Rousta, Mansoureh; Shokraneh, Farhad; Rahimi-Movaghar, Vafa

2017-06-01

Alcohol consumption can lead to risky driving and increase the frequency of traffic accidents, injuries and mortalities. The main purpose of our study was to compare simulated driving performance between two groups of drivers, one consumed alcohol and the other not consumed, using a systematic review. In this systematic review, electronic resources and databases including Medline via Ovid SP, EMBASE via Ovid SP, PsycINFO via Ovid SP, PubMed, Scopus, Cumulative Index to Nursing and Allied Health Literature (CINHAL) via EBSCOhost were comprehensively and systematically searched. The randomized controlled clinical trials that compared simulated driving performance between two groups of drivers, one consumed alcohol and the other not consumed, were included. Lane position standard deviation (LPSD), mean of lane position deviation (MLPD), speed, mean of speed deviation (MSD), standard deviation of speed deviation (SDSD), number of accidents (NA) and line crossing (LC) were considered as the main parameters evaluating outcomes. After title and abstract screening, the articles were enrolled for data extraction and they were evaluated for risk of biases. Thirteen papers were included in our qualitative synthesis. All included papers were classified as high risk of biases. Alcohol consumption mostly deteriorated the following performance outcomes in descending order: SDSD, LPSD, speed, MLPD, LC and NA. Our systematic review had troublesome heterogeneity. Alcohol consumption may decrease simulated driving performance in alcohol consumed people compared with non-alcohol consumed people via changes in SDSD, LPSD, speed, MLPD, LC and NA. More well-designed randomized controlled clinical trials are recommended. Copyright © 2017. Production and hosting by Elsevier B.V.

Alcohol consumption for simulated driving performance: A systematic review

Institute of Scientific and Technical Information of China (English)

Mohammad Saeid Rezaee-Zavareh; Payman Salamati; Mahdi Ramezani-Binabaj; Mina Saeidnejad; Mansoureh Rousta; Farhad Shokraneh; Vafa Rahimi-Movaghar

2017-01-01

Purpose:Alcohol consumption can lead to risky driving and increase the frequency of traffic accidents,injuries and mortalities.The main purpose of our study was to compare simulated driving performance between two groups of drivers,one consumed alcohol and the other not consumed,using a systematic review.Methods:In this systematic review,electronic resources and databases including Medline via Ovid SP,EMBASE via Ovid SP,PsycINFO via Ovid SP,PubMed,Scopus,Cumulative Index to Nursing and Allied Health Literature (CINHAL) via EBSCOhost were comprehensively and systematically searched.The randomized controlled clinical trials that compared simulated driving performance between two groups of drivers,one consumed alcohol and the other not consumed,were included.Lane position standard deviation (LPSD),mean of lane position deviation (MLPD),speed,mean of speed deviation (MSD),standard deviation of speed deviation (SDSD),number of accidents (NA) and line crossing (LC) were considered as the main parameters evaluating outcomes.After title and abstract screening,the articles were enrolled for data extraction and they were evaluated for risk of biases.Results:Thirteen papers were included in our qualitative synthesis.All included papers were classified as high risk of biases.Alcohol consumption mostly deteriorated the following performance outcomes in descending order:SDSD,LPSD,speed,MLPD,LC and NA.Our systematic review had troublesome heterogeneity.Conclusion:Alcohol consumption may decrease simulated driving performance in alcohol consumed people compared with non-alcohol consumed people via changes in SDSD,LPSD,speed,MLPD,LC and NA.More well-designed randomized controlled clinical trials are recommended.

Key Performance Parameter Driven Technology Goals for Electric Machines and Power Systems

Science.gov (United States)

Bowman, Cheryl; Jansen, Ralph; Brown, Gerald; Duffy, Kirsten; Trudell, Jeffrey

2015-01-01

Transitioning aviation to low carbon propulsion is one of the crucial strategic research thrust and is a driver in the search for alternative propulsion system for advanced aircraft configurations. This work requires multidisciplinary skills coming from multiple entities. The feasibility of scaling up various electric drive system technologies to meet the requirements of a large commercial transport is discussed in terms of key parameters. Functional requirements are identified that impact the power system design. A breakeven analysis is presented to find the minimum allowable electric drive specific power and efficiency that can preserve the range, initial weight, operating empty weight, and payload weight of the base aircraft.

Greenhouse gas emission impacts of electric vehicles under varying driving cycles in various counties and US cities

International Nuclear Information System (INIS)

Wang, M.Q.; Marr, W.W.

1994-01-01

Electric vehicles (EVs) can reduce greenhouse gas emissions, relative to emissions from gasoline-fueled vehicles. However, those studies have not considered all aspects that determine greenhouse gas emissions from both gasoline vehicles (GVs) and EVs. Aspects often overlooked include variations in vehicle trip characteristics, inclusion of all greenhouse gases, and vehicle total fuel cycle. In this paper, we estimate greenhouse gas emission reductions for EVs, including these important aspects. We select four US cities (Boston, Chicago, Los Angeles, and Washington, D.C.) and six countries (Australia, France, Japan, Norway, the United Kingdom, and the United States) and analyze greenhouse emission impacts of EVs in each city or country. We also select six driving cycles developed around the world (i.e., the US federal urban driving cycle, the Economic Community of Europe cycle 15, the Japanese 10-mode cycle, the Los Angeles 92 cycle, the New York City cycle, and the Sydney cycle). Note that we have not analyzed EVs in high-speed driving (e.g., highway driving), where the results would be less favorable to EVs; here, EVs are regarded as urban vehicles only. We choose one specific driving cycle for a given city or country and estimate the energy consumption of four-passenger compact electric and gasoline cars in the given city or country. Finally, we estimate total fuel cycle greenhouse gas emissions of both GVs and EVs by accounting for emissions from primary energy recovery, transportation, and processing; energy product transportation; and powerplant and vehicle operations

Light duty vehicle transportation and global climate policy: The importance of electric drive vehicles

International Nuclear Information System (INIS)

Bosetti, Valentina; Longden, Thomas

2013-01-01

With a focus on the interaction between long-term climate targets and personal transport we review the electrification of light duty vehicles (LDVs) within a model that utilizes a learning-by-researching structure. By modeling the demand of vehicles, the use of fuels and emissions implied, the model solves for the optimum RD and D investments that decrease the cost of hybrid, plug-in hybrid and electric vehicles. A range of technology and climate policy scenarios provide long term projections of vehicle use that highlight the potential synergies between innovation in the transportation sector and the energy sector. We find that even when the capital cost of electric drive vehicles (EDVs) remains higher than that of traditional combustion engine alternatives, EDVs are likely to play a key role in the decarbonisation implied by stringent climate policy. Limited innovation in batteries results in notable increases in policy costs consistent with a two degree climate policy target. - Highlights: • Significant increase in vehicles across regions in the medium to long term future. • Climate policy costs are sensitive to a lack of electric drive vehicles (EDVs). • Achieving 450ppm with no change in battery costs has a policy cost that is 2.86 percentage points higher than the base 450ppm scenario. • Climate policy hastens the introduction of electrified vehicles, however EDVs do not become the dominant vehicle of choice before the middle of the century

Investigation of efficiency of electric drive control system of excavator traction mechanism based on feedback on load

Science.gov (United States)

Kuznetsov, N. K.; Iov, I. A.; Iov, A. A.

2018-05-01

The article presents the results of a study of the efficiency of the electric drive control system of the traction mechanism of a dragline based on the use of feedback on load in the traction cable. The investigations were carried out using a refined electromechanical model of the traction mechanism, which took into account not only the elastic elements of the gearbox, the backlashes in it and the changes in the kinematic parameters of the mechanism during operation, but also the mechanical characteristics of the electric drive and the features of its control system. By mathematical modeling of the transient processes of the electromechanical system, it is shown that the introduction of feedback on the load in the elastic element allows one to reduce the dynamic loads in the traction mechanism and to limit the elastic oscillations of the actuating mechanism in comparison with the standard control system. Fixed as a general decrease in the dynamic load of the nodes of traction mechanism in the modes of loading and latching of the bucket, and a decrease the operating time of the mechanism at maximum load. At the same time, undesirable phenomena in the operation of the electric drive were also associated with the increase in the recovery time of the steady-state value of the speed of the actuating mechanism under certain operating conditions, which can lead to a decrease in the reliability of the mechanical part and the productivity of the traction mechanism.

Electrical machines diagnosis

CERN Document Server

Trigeassou, Jean-Claude

2013-01-01

Monitoring and diagnosis of electrical machine faults is a scientific and economic issue which is motivated by objectives for reliability and serviceability in electrical drives.This book provides a survey of the techniques used to detect the faults occurring in electrical drives: electrical, thermal and mechanical faults of the electrical machine, faults of the static converter and faults of the energy storage unit.Diagnosis of faults occurring in electrical drives is an essential part of a global monitoring system used to improve reliability and serviceability. This diagnosis is perf

Class-D amplifier design and performance for driving a Piezo Actuator Drive servomotor

DEFF Research Database (Denmark)

Zsurzsan, Tiberiu-Gabriel; Zhang, Zhe; Andersen, Michael A. E.

2016-01-01

This paper investigates the behavior of piezoelectric stacks in a Piezoelectric Actuator Drive (PAD) motor, which shows non-linear equivalent impedance and has a dramatic impact on the overall system performance. Therefore, in this paper, the piezo stackt’s model is discussed and an improved large...

Repeated-dose effects of mequitazine, cetirizine and dexchlorpheniramine on driving and psychomotor performance.

Science.gov (United States)

Theunissen, Eef L; Vermeeren, Annemiek; Ramaekers, Johannes G

2006-01-01

Previous studies have demonstrated that the antihistamines mequitazine, cetirizine and dexchlorpheniramine produce mild sedation after single doses. It is unknown, however, whether acute sedation persists after repeated dosing. Therefore, this study assessed the effects of repeated dosing of these antihistamines on driving and psychomotor performance. Sixteen healthy volunteers were treated with mequitazine 10 mg q.a.m., cetirizine 10 mg q.a.m., dexchlorpheniramine Repetab 6 mg b.i.d. and placebo for four separate 8-day periods. Drug effects were assessed on days 1 and 8 using on-the-road driving tests (highway driving and car following), psychomotor tests (tracking and divided attention) and subjective questionnaires. Dexchlorpheniramine and mequitazine significantly impaired driving performance on the highway driving test on the first day; dexchlorpheniramine increased Standard Deviation of Lateral Position by 2 cm [95% confidence interval (CI) 0.5, 3.8] and mequitazine by 2.5 cm (CI 1.0, 4.3). These effects on driving performance disappeared after 8 days of treatment. No effect of treatment was found on car following, tracking and divided attention. Although subjective ratings confirmed that subjects knew their driving had been impaired in the mequitazine and dexchlorpheniramine condition after completion of the highway driving test on day 1, they did not expect their driving to be affected before the start of the test. Cetirizine did not impair performance on any of the tests. Single doses of mequitazine 10 mg and dexchlorpheniramine Repetab 6 mg cause mild driving impairment. However, when taken over several days, the impairing effect wears off, possibly as a result of tolerance.

Radiation dose, driving performance, and cognitive function in patients with head and neck cancer

International Nuclear Information System (INIS)

Yuen, Hon K.; Sharma, Anand K.; Logan, William C.; Gillespie, M. Boyd; Day, Terry A.; Brooks, Johnell O.

2008-01-01

Seven head and neck cancer patients participated in a driving evaluation in a driving simulator. Radiation dose on the temporal lobes was moderately associated with time to complete a cognitive test and with driving performance. Results indicated that incidental irradiation may contribute to a decrease in cognition and in unsafe driving performance, which seems to be time-dependent

Engineering of Machine tool’s High-precision electric drives

Science.gov (United States)

Khayatov, E. S.; Korzhavin, M. E.; Naumovich, N. I.

2018-03-01

In the article it is shown that in mechanisms with numerical program control, high quality of processes can be achieved only in systems that provide adjustment of the working element’s position with high accuracy, and this requires an expansion of the regulation range by the torque. In particular, the use of synchronous reactive machines with independent excitation control makes it possible to substantially increase the moment overload in the sequential excitation circuit. Using mathematical and physical modeling methods, it is shown that in the electric drive with a synchronous reactive machine with independent excitation in a circuit with sequential excitation, it is possible to significantly expand the range of regulation by the torque and this is achieved by the effect of sequential excitation, which makes it possible to compensate for the transverse reaction of the armature.

Dynamic performances analysis of a real vehicle driving

Science.gov (United States)

Abdullah, M. A.; Jamil, J. F.; Salim, M. A.

2015-12-01

Vehicle dynamic is the effects of movement of a vehicle generated from the acceleration, braking, ride and handling activities. The dynamic behaviours are determined by the forces from tire, gravity and aerodynamic which acting on the vehicle. This paper emphasizes the analysis of vehicle dynamic performance of a real vehicle. Real driving experiment on the vehicle is conducted to determine the effect of vehicle based on roll, pitch, and yaw, longitudinal, lateral and vertical acceleration. The experiment is done using the accelerometer to record the reading of the vehicle dynamic performance when the vehicle is driven on the road. The experiment starts with weighing a car model to get the center of gravity (COG) to place the accelerometer sensor for data acquisition (DAQ). The COG of the vehicle is determined by using the weight of the vehicle. A rural route is set to launch the experiment and the road conditions are determined for the test. The dynamic performance of the vehicle are depends on the road conditions and driving maneuver. The stability of a vehicle can be controlled by the dynamic performance analysis.

Age and visual impairment decrease driving performance as measured on a closed-road circuit.

Science.gov (United States)

Wood, Joanne M

2002-01-01

In this study the effects of visual impairment and age on driving were investigated and related to visual function. Participants were 139 licensed drivers (young, middle-aged, and older participants with normal vision, and older participants with ocular disease). Driving performance was assessed during the daytime on a closed-road driving circuit. Visual performance was assessed using a vision testing battery. Age and visual impairment had a significant detrimental effect on recognition tasks (detection and recognition of signs and hazards), time to complete driving tasks (overall course time, reversing, and maneuvering), maneuvering ability, divided attention, and an overall driving performance index. All vision measures were significantly affected by group membership. A combination of motion sensitivity, useful field of view (UFOV), Pelli-Robson letter contrast sensitivity, and dynamic acuity could predict 50% of the variance in overall driving scores. These results indicate that older drivers with either normal vision or visual impairment had poorer driving performance compared with younger or middle-aged drivers with normal vision. The inclusion of tests such as motion sensitivity and the UFOV significantly improve the predictive power of vision tests for driving performance. Although such measures may not be practical for widespread screening, their application in selected cases should be considered.

X-ray system with coupled source drive and detector drive

International Nuclear Information System (INIS)

1976-01-01

An electronic coupling replacing the (more expensive) mechanical coupling which controls the speed of two sets of two electric motors, one driving an X-ray source and the other an X-ray detector, is described. Source and detector are kept rotating in parallel planes with a fairly constant velocity ratio. The drives are controlled by an electronic system comprising a comparator circuit comparing the position-indicative signals, a process control circuit and an inverter switch. The control system regulates the speed of the electric motors. The signal processing is described

A pilot study of the effects of atomoxetine on driving performance in adults with ADHD.

Science.gov (United States)

Barkley, Russell A; Anderson, Deborah L; Kruesi, Markus

2007-02-01

There is a high risk of vehicular crashes, traffic citations, and poorer driving performance in adults with ADHD. This pilot study examines the value of a new nonstimulant (atomoxetine) for improving the driving performance of adults with ADHD. Atomoxetine (1.2 mg/kg daily for 3 weeks) and a placebo are studied on 18 adults with ADHD (M age = 37 years) using ratings of ADHD symptoms, impairment, and safe driving behavior; a virtual reality driving simulator; and ratings of simulator performance. Atomoxetine improves self-ratings of ADHD symptoms, impairments, safe driving behavior, and simulator driving performance. No effects of atomoxetine are evident on others' ratings of driving behavior or on the simulator. Practice effects on the simulator may have obscured those drug effects. The authors find a mixed pattern of results such that atomoxetine warrants further study for its effects on driving in this high-risk population.

Prospects for the application of GaN power devices in hybrid electric vehicle drive systems

Science.gov (United States)

Su, Ming; Chen, Chingchi; Rajan, Siddharth

2013-07-01

GaN, a wide bandgap semiconductor successfully implemented in optical and high-speed electronic devices, has gained momentum in recent years for power electronics applications. Along with rapid progress in material and device processing technologies, high-voltage transistors over 600 V have been reported by a number of teams worldwide. These advances make GaN highly attractive for the growing market of electrified vehicles, which currently employ bipolar silicon devices in the 600-1200 V class for the traction inverter. However, to capture this billion-dollar power market, GaN has to compete with existing IGBT products and deliver higher performance at comparable or lower cost. This paper reviews key achievements made by the GaN semiconductor industry, requirements of the automotive electric drive system and remaining challenges for GaN power devices to fit in the inverter application of hybrid vehicles.

COMPARATIVE ANALYSIS OF CONVERTER STRUCTURES OF THE TRACTION DRIVE PROSPECTIVE MULTI-SYSTEM ELECTRIC LOCOMOTIVES WITH DC TRACTION MOTORS

Directory of Open Access Journals (Sweden)

A. M. Muha

2009-03-01

Full Text Available In the article the structured schemes of steady-state converter are offered for traction drive of promising multisystem electric locomotives with traction engines of direct current and their comparative analysis is conducted.

Test facilities for hybrid and electric drive trains; Stazione di prova sistemi di trazione ibridi ed elettrici

Energy Technology Data Exchange (ETDEWEB)

Bernardini, G.; Ciancia, A.; De Andreis, L.; Pagni, G.; Pede, G.; Rossi, E.; Vellone, R. [ENEA, Centro Ricerche Casaccia, Rome (Italy). Dip. Energia

1998-12-31

ENEA (Italian National Agency for New Technologies, Energy and the Environment) is conducting a large research and development programme on innovative vehicles with high energy efficiency and low environmental impact. In particular conducts activities on electric and hybrid vehicles. Testing and evaluation activities play a strong role in this programme. A complete characterization chain has been then defined and set up with a network of facilities which covers main testing needs for single components, subsystems and complete vehicles, in simulated and real operating conditions. The test facility which has been realised is able to experiment and fully characterise complete drive-trains (and subsystems) for pure electric and hybrid vehicles. It is composed by a different section for each subsystem: 1) power generation; 2) energy storage and management; 3) driving motors. Each section acts as an experimental island, able to operate alone or jointly with the other sections. In fact, all the sections are remotely controlled and managed in order to create different assembly of the drive-train. The facility has been sized to allow the testing of drive-trains and subsystems of small and medium-sized vehicles (up to minibuses), but an extension to larger vehicles is possible. During 1996 and part of 1997 the Drive train Test Facility has been completed and made operative. This paper mainly presents the final configurations of these novel testing systems with peculiar features and characteristics. [Italiano] ENEA (Ente Nazionale per le nuove tecnologie, l`Energia e l`Ambiente) sta conducendo un vasto programma di ricerca e sviluppo sui veicoli innovativi ad alto rendimento energetico e basso impatto ambientale.

Changes in driving behavior and cognitive performance with different breath alcohol concentration levels.

Science.gov (United States)

Liu, Yung-Ching; Fu, Shing-Mei

2007-06-01

This study examines the changes in driving behavior and cognitive performance of drivers with different breath alcohol concentration (BrAC) levels. Eight licensed drivers, aged between 20 and 30 years, with BrAC levels of 0.00, 0.25, 0.4 and 0.5 mg/l performed simulated driving tests under high- and low-load conditions. Subjects were asked to assess their subjective psychological load at specified intervals and perform various tasks. The outcome was measured in terms of reaction times for task completion, accuracy rates, and driver's driving behavior. The effects of BrAC vary depending on the task. Performance of tasks involving attention shift, information processing, and short-term memory showed significant deterioration with increasing BrAC, while dangerous external vehicle driving behavior occurred only when the BrAC reached 0.4 mg/l and the deterioration was marked. We can conclude that the cognitive faculty is the first to be impaired by drinking resulting in deteriorated performance in tasks related to divided attention, short-term memory, logical reasoning, followed by visual perception. On the other hand, increasing alcohol dose may not pose an immediate impact on the external vehicle driving behavior but may negatively affect the driver's motor behavior even at low BrAC levels. Experience and will power could compensate for the negative influence of alcohol enabling the drivers to remain in full steering control. This lag between alcohol consumption and impaired driving performance may mislead the drivers in thinking that they are still capable of safe steering and cause them to ignore the potential dangers of drunk driving.

The Question of Energy-Efficient Design of the Automated Electric Drive of Multi-Engine Belt Conveyors

Directory of Open Access Journals (Sweden)

Semykina Irina

2015-01-01

Full Text Available The article proposes a method for improving the energy efficiency of multi-motor variable frequency electric drives of trunk belt conveyors, based on the conveyor speed changing and controlling of the magnetic state of the motor. At conclusion, economic and energy effects of the implementation are estimated.

Electric driving in 2050. Consequences for the living environment; Elektrisch rijden in 2050. Gevolgen voor de leefomgeving

Energy Technology Data Exchange (ETDEWEB)

Nijland, H.; Hoen, A.; Snellen, D.; Zondag, B.

2012-11-15

The ambition of the Dutch government was to realize a million cars driving on electricity in the Netherlands by 2050. This way the cabinet aimed to reduce the dependency on fossil fuels and to contribute to the European targets regarding the CO2 emissions of transport in 2050. These emissions need to be reduced by 60 per cent compared to 1990. To reach the climate targets, the EU also plans to ban cars with combustion engines from the European cities. A full switch to electric passenger cars can make a significant contribution to the realization of these targets. Therefore, PBL (the Environmental Assessment Agency) explored the consequences of such a full switch to electric passenger car mobility. The transition to electric cars enables the realization of approximately half of the long-term climate ambitions for the traffic and transport sector. The environment, particularly in the cities, profits from a transition to electric driving, because it reduces both the emission of air-polluting substances and noise pollution. On the main roads and the regional roads, however, electric driving does not lead to a reduction in noise pollution. The electricity grid will need to be modified to be able to meet the growing demand [Dutch] De ambitie van het kabinet-Rutte was dat er in 2025 een miljoen auto's op elektriciteit rijden in Nederland. Hiermee wilde het kabinet de afhankelijkheid van fossiele brandstoffen verminderen en een bijdrage leveren aan de in Europees verband afgesproken doelen rondom de uitstoot van de CO2-emissies door transport in 2050. Deze uitstoot moet met 60 procent verminderen ten opzichte van 1990. Om de klimaatdoelen te halen, wil de EU bovendien auto's met verbrandingsmotoren weren uit de Europese steden. Een volledige omschakeling naar elektrisch rijden van personenauto's kan een belangrijke bijdrage leveren aan deze doelen. Het PBL heeft daarom de gevolgen verkend van zo'n volledige omschakeling naar elektrische

Equivalent model of a dually-fed machine for electric drive control systems

Science.gov (United States)

Ostrovlyanchik, I. Yu; Popolzin, I. Yu

2018-05-01

The article shows that the mathematical model of a dually-fed machine is complicated because of the presence of a controlled voltage source in the rotor circuit. As a method of obtaining a mathematical model, the method of a generalized two-phase electric machine is applied and a rotating orthogonal coordinate system is chosen that is associated with the representing vector of a stator current. In the chosen coordinate system in the operator form the differential equations of electric equilibrium for the windings of the generalized machine (the Kirchhoff equation) are written together with the expression for the moment, which determines the electromechanical energy transformation in the machine. Equations are transformed so that they connect the currents of the windings, that determine the moment of the machine, and the voltages on these windings. The structural diagram of the machine is assigned to the written equations. Based on the written equations and accepted assumptions, expressions were obtained for the balancing the EMF of windings, and on the basis of these expressions an equivalent mathematical model of a dually-fed machine is proposed, convenient for use in electric drive control systems.

The Effects of Medical Conditions on Driving Performance

Science.gov (United States)

2017-08-01

This project investigated the effect of selected medical conditions on the exposure and performance of older drivers. A review of recent literature, followed by a panel meeting with driving safety experts, prioritized four medical conditions for furt...

Development of in-vessel type control rod drive mechanism for a innovative small reactor (Contract research)

Energy Technology Data Exchange (ETDEWEB)

Yoritsune, Tsutomu; Ishida, Toshihisa [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2003-03-01

Although the control rod drive mechanism of an existing large scale light water reactor is generally installed outside the reactor vessel, an in-vessel type control rod drive mechanism (INV-CRDM) is installed inside the reactor vessel. The INV-CRDM contributes to compactness and simplicity of the reactor system, and it can eliminate the possibility of a rod ejection accident. Therefore, INV-CRDM is an important technology adopted in an innovative small reactor. Japan Atomic Energy Research Institute (JAERI) has developed this type of CRDM driven by an electric motor, which can work under high temperature and high pressure water for the advanced marine reactor. On the basis of this research result, a driving motor coil and a bearing were developed to be used under the high temperature steam, severe condition for an innovative small reactor. About the driving motor, we manufactured the driving motor available for high temperature steam and carried out performance test under room temperature atmosphere to confirm the electric characteristic and coolability of the driving coil. With these test results and the past test results under high temperature water, we analyzed and evaluated the electric performance and coolability of the driving coil under high temperature steam. Concerning bearing, we manufactured the test pieces using some candidate material for material characteristic test and carried out the rolling wear test under high temperature steam to select the material. Consequently, we confirmed that performance of the driving coil for the advanced type driving motor, is enough to be used under high temperature steam. And, we evaluated the performance of the bearing and selected the material of the bearing, which can be used under high temperature steam. From these results, we have obtained the prospect that the INV-CRDM can be used for an innovative small reactor under steam atmosphere could be developed. (author)

The effects of texting on driving performance in a driving simulator: the influence of driver age.

Science.gov (United States)

Rumschlag, Gordon; Palumbo, Theresa; Martin, Amber; Head, Doreen; George, Rajiv; Commissaris, Randall L

2015-01-01

Distracted driving is a significant contributor to motor vehicle accidents and fatalities, and texting is a particularly significant form of driver distraction that continues to be on the rise. The present study examined the influence of driver age (18-59 years old) and other factors on the disruptive effects of texting on simulated driving behavior. While 'driving' the simulator, subjects were engaged in a series of brief text conversations with a member of the research team. The primary dependent variable was the occurrence of Lane Excursions (defined as any time the center of the vehicle moved outside the directed driving lane, e.g., into the lane for oncoming traffic or onto the shoulder of the road), measured as (1) the percent of subjects that exhibited Lane Excursions, (2) the number of Lane Excursions occurring and (3) the percent of the texting time in Lane Excursions. Multiple Regression analyses were used to assess the influence of several factors on driving performance while texting, including text task duration, texting skill level (subject-reported), texting history (#texts/week), driver gender and driver age. Lane Excursions were not observed in the absence of texting, but 66% of subjects overall exhibited Lane Excursions while texting. Multiple Regression analysis for all subjects (N=50) revealed that text task duration was significantly correlated with the number of Lane Excursions, and texting skill level and driver age were significantly correlated with the percent of subjects exhibiting Lane Excursions. Driver gender was not significantly correlated with Lane Excursions during texting. Multiple Regression analysis of only highly skilled texters (N=27) revealed that driver age was significantly correlated with the number of Lane Excursions, the percent of subjects exhibiting Lane Excursions and the percent of texting time in Lane Excursions. In contrast, Multiple Regression analysis of those drivers who self-identified as not highly skilled

Performance of an all-electric vehicle under UN ECE R101 test conditions: A feasibility study for the city of Kaunas, Lithuania

International Nuclear Information System (INIS)

Raslavičius, Laurencas; Starevičius, Martynas; Keršys, Artūras; Pilkauskas, Kęstutis; Vilkauskas, Andrius

2013-01-01

Transport activity has been a key facilitator and driver of economic prosperity in Lithuanian (hereinafter LIT) and it is likely to continue to grow. It can produce both positive and negative effects on the quality of life and the environment depending on country-specific circumstances. This research paper sets the stage for a look at the LIT passenger vehicle fleet and its transition towards sustainable mobility through the use of all-electric vehicles. The large multi purpose vehicle from French car-maker Renault, model Renault Espace, was used for test drives, according ECE R101 (urban cycle) requirements. The conventional spark ignited internal combustion engine of the vehicle was replaced by the electric one and equipped with the new generation LiFePO 4 Lithium-ion rechargeable batteries. Three streets of Kaunas city (LIT) with different categories B1, B2 and C2 were selected for the test procedure. Estimation of the power demand (depending on displacement and daytime) and evaluation of battery performance characteristics were discussed in detail. Calculation of the driving distance of the one charge of the traction battery estimates several driving conditions and variation of the mass of the investigated vehicle. Comparison of consumption of different fuel grades for 1 km showed that costs of electric power driven vehicle is 4 times as low as with A95 grade petrol and 2.4 times as low as with diesel fuel. - Highlights: • This paper examines the perspectives for electric vehicles use in Lithuania. • We used standardized test procedure UN ECE R101 (urban cycle). • The study found that the BEVs (battery-only electric vehicles) can cover approximately 75% of all daily driving. • Inspection of the results highlights the importance of BEVs introduction. • We have shown that battery-only electric vehicles are economically rational

Haulage trucks model with four electric separate wheel drives

Directory of Open Access Journals (Sweden)

R. Setlak

2005-02-01

Full Text Available This article contains a course of work of the construction of a vehicle model that has four electrical motors built into each wheel. During the project two models of a vehicle were constructed. A microprocessor based control system has also been designed and built. A vehicle is controlled by a steering unit which contains a steering wheel with a force feedback system, push buttons, an accelerator and a brake. The connection between a steering unit and a model is realized by interface RS-485. The driving motors are dc motors with permanent magnets. Power supply consists of an acid battery located in the vehicle. The vehicle control system is divided into two parts. The first part is built into the vehicle and operates as a vehicle main control system and the second is built into a steering unit and operates as the main control steering system.

Freeway Driving Cycle Construction Based on Real-Time Traffic Information and Global Optimal Energy Management for Plug-In Hybrid Electric Vehicles

Directory of Open Access Journals (Sweden)

Hongwen He

2017-11-01

Full Text Available This paper presents a freeway driving cycle (FDC construction method based on traffic information. A float car collected different type of roads in California and we built a velocity fragment database. We selected a real freeway driving cycle (RFDC and established the corresponding time traffic information tensor model by using the data in California Department of Transportation performance measure system (PeMS. The correlation of road velocity in the time dimension and spatial dimension are analyzed. According to the average velocity of road sections at different times, the kinematic fragments are stochastically selected in the velocity fragment database to construct a real-time FDC of each section. The comparison between construction freeway driving cycle (CFDC and real freeway driving cycle (RFDC show that the CFDC well reflects the RFDC characteristic parameters. Compared to its application in plug-in electric hybrid vehicle (PHEV optimal energy management based on a dynamic programming (DP algorithm, CFDC and RFDC fuel consumption are similar within approximately 5.09% error, and non-rush hour fuel economy is better than rush hour 3.51 (L/100 km at non-rush hour, 4.29 (L/km at rush hour. Moreover, the fuel consumption ratio can be up to 13.17% in the same CFDC at non-rush hour.

Proceedings of the Prop'Elec 2000 colloquium. Advances of electric drive in urban transportation systems; Actes du colloque Prop'Elec 2000. Progres de la traction electrique dans les transports urbains

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

This document is the proceedings of Prop'Elec 2000 colloquium on the advances in electric power drive in urban transportation systems. The colloquium comprises 5 sessions dealing with: 1 - public collective electric-powered transportation system: synthesis of urban guided systems (C. Soulas, INRETS), the fast travelator (A. Cote, RATP), the power supply system of METEOR automatic underground railway (P. Lagrange, W. Seiler, RATP); 2 - electrical drive in urban transportation systems: start-up of a thermal engine with super-capacitors (D. Bouquain (CREEBEL), H. Gualous, A. Djerdir, A. Berthon, J.M. Kauffmann (L2ES, IGE)), The LEV (light weight electric vehicle) project in Mendrisio (U. Schwegler, LEV/Suisse), prototype of electrical bike that use a wheel-engine (C. Espanet, F. Gustin, J.M. Kauffmann (IGE), S. Robert, M. Karmous (EICN)), TWIL: a new generation of small electrical bikes (E. Escallot, T. Bontems (EPMI)), thermal and magnetic analysis of a rectilinear movement actuator (J.C. Vannier, M. Kadiri (SUPELEC)), torque undulation and vibrations in automobile electrical drives (A.L. Bui-Van (Renault), A. Fonseca (LEG)); 3 - collective electric-powered transportation systems: STARS: autonomous transportation system with flywheel charging at the station (P. Gibard (Alstom Transport), K. Abuda, J.M. Vinassa (IXL Bordeaux)), Translhor tramway: presentation of the drive system (L. Verdier, LHOR); 4 - electric-powered and hybrid vehicles: batteries for electric-powered vehicles (J.F. Fauvarque, CNAM), Li-ion batteries and their application in automotive industry (T. Faugeras, SAFT), optimized drive systems for electric-powered vehicles (J. Saint-Michel, Leroy Somer), the Citroen Xsara Dynactive (S. Derou, PSA), 5 - electric-powered and hybrid vehicles: the electrical car in tomorrows' city (M. Parent, INRIA), the market of electric-powered vehicles in France and Europe (M. Valet, PSA). (J.S.)

Performance Evaluation of an In-Wheel Motor Cooling System in an Electric Vehicle/Hybrid Electric Vehicle

Directory of Open Access Journals (Sweden)

Dong Hyun Lim

2014-02-01

Full Text Available High power and miniaturization of motors in an in-wheel drive system, which is installed inside the wheels of a vehicle, are required for directly driving the wheels. In addition, an efficient cooling system is required to ensure high driving performance and durability. This study experimentally evaluated the heat dissipation performance of a 35-kW-class large-capacity in-wheel motor equipped with an internal-circulation-type oil-cooling system that exhibits high cooling performance and can be easily miniaturized to this motor. Temperatures of the coil and stator core of cooling systems with and without a radiator were measured in real time under in-wheel motor driving conditions. It was found that operating the cooling system at a continuous-rating maximum speed without the radiator was difficult. We confirmed that under continuous-rating base speed and continuous-rating maximum speed driving conditions, the cooling system with the radiator showed thermally stable operation. Furthermore, under maximum-rating base speed and maximum-rating maximum speed driving conditions, the cooling system with the radiator provided additional driving times of approximately 22 s and 2 s, respectively.

The influence of drinking, texting, and eating on simulated driving performance.

Science.gov (United States)

Irwin, Christopher; Monement, Sophie; Desbrow, Ben

2015-01-01

Driving is a complex task and distractions such as using a mobile phone for the purpose of text messaging are known to have a significant impact on driving. Eating and drinking are common forms of distraction that have received less attention in relation to their impact on driving. The aim of this study was to further explore and compare the effects of a variety of distraction tasks (i.e., text messaging, eating, drinking) on simulated driving. Twenty-eight healthy individuals (13 female) participated in a crossover design study involving 3 experimental trials (separated by ≥24 h). In each trial, participants completed a baseline driving task (no distraction) before completing a second driving task involving one of 3 different distraction tasks (drinking 400 mL water, drinking 400 mL water and eating a 6-inch Subway sandwich, drinking 400 mL water and composing 3 text messages). Primary outcome measures of driving consisted of standard deviation of lateral position (SDLP) and reaction time to auditory and visual critical events. Subjective ratings of difficulty in performing the driving tasks were also collected at the end of the study to determine perceptions of distraction difficulty on driving. Driving tasks involving texting and eating were associated with significant impairment in driving performance measures for SDLP compared to baseline driving (46.0 ± 0.08 vs. 41.3 ± 0.06 cm and 44.8 ± 0.10 vs. 41.6 ± 0.07 cm, respectively), number of lane departures compared to baseline driving (10.9 ± 7.8 vs. 7.6 ± 7.1 and 9.4 ± 7.5 vs. 7.1 ± 7.0, respectively), and auditory reaction time compared to baseline driving (922 ± 95 vs. 889 ± 104 ms and 933 ± 101 vs. 901 ± 103 ms, respectively). No difference in SDLP (42.7 ± 0.08 vs. 42.5 ± 0.07 cm), number of lane departures (7.6 ± 7.7 vs. 7.0 ± 6.8), or auditory reaction time (891 ± 98 and 885 ± 89 ms) was observed in the drive involving the drink-only condition compared to the corresponding baseline drive

Post and during event effect of cell phone talking and texting on driving performance--a driving simulator study.

Science.gov (United States)

Thapa, Raju; Codjoe, Julius; Ishak, Sherif; McCarter, Kevin S

2015-01-01

A number of studies have been done in the field of driver distraction, specifically on the use of cell phone for either conversation or texting while driving. Researchers have focused on the driving performance of drivers when they were actually engaged in the task; that is, during the texting or phone conversation event. However, it is still unknown whether the impact of cell phone usages ceases immediately after the end of task. The primary objective of this article is to analyze the post-event effect of cell phone usage (texting and conversation) in order to verify whether the distracting effect lingers after the actual event has ceased. This study utilizes a driving simulator study of 36 participants to test whether a significant decrease in driver performance occurs during cell phone usage and after usage. Surrogate measures used to represent lateral and longitudinal control of the vehicle were standard deviation (SD) of lane position and mean velocity, respectively. RESULTS suggest that there was no significant decrease in driver performance (both lateral and longitudinal control) during and after the cell phone conversation. For the texting event, there were significant decreases in driver performance in both the longitudinal and lateral control of the vehicle during the actual texting task. The diminished longitudinal control ceased immediately after the texting event but the diminished lateral control lingered for an average of 3.38 s. The number of text messages exchanged did not affect the magnitude or duration of the diminished lateral control. The result indicates that the distraction and subsequent elevated crash risk of texting while driving linger even after the texting event has ceased. This finding has safety and policy implications in reducing distracted driving.

Prospects for the application of GaN power devices in hybrid electric vehicle drive systems

International Nuclear Information System (INIS)

Su, Ming; Chen, Chingchi; Rajan, Siddharth

2013-01-01

GaN, a wide bandgap semiconductor successfully implemented in optical and high-speed electronic devices, has gained momentum in recent years for power electronics applications. Along with rapid progress in material and device processing technologies, high-voltage transistors over 600 V have been reported by a number of teams worldwide. These advances make GaN highly attractive for the growing market of electrified vehicles, which currently employ bipolar silicon devices in the 600–1200 V class for the traction inverter. However, to capture this billion-dollar power market, GaN has to compete with existing IGBT products and deliver higher performance at comparable or lower cost. This paper reviews key achievements made by the GaN semiconductor industry, requirements of the automotive electric drive system and remaining challenges for GaN power devices to fit in the inverter application of hybrid vehicles. (invited review)

Efficiency improvement of variable speed electrical drives for HVAC applications

Energy Technology Data Exchange (ETDEWEB)

Abrahamsen, F.; Blaabjerg, F.; Pedersen, J.K. [Aalborg Univ., Inst. of Energy Technology, Aalborg East (Denmark)

2000-07-01

A large part of the produced electrical energy is consumed by ventilators, pumps and compressors, the so-called HVAC applications. A lot of this energy can be saved by speed control, but even with the large saving obtained alone by introduction of variable speed, it is still essential to optimise the control of the variable speed drive and to optimise the electrical machine with respect to efficiency. Experiments are made with energy optimal induction motor control on a 2.2 kW variable speed pump system. It is demonstrated that 10% of the consumed energy can typically be saved by energy optimal motor control compared with constant V/Hz control. In a comparison of induction motors and permanent magnet synchronous motors for a variable speed pump application it is shown that for 2.2 kW motors an investment in high-efficiency or PM motors are typically paid back within 2.5 years and 7 years respectively. For a 90 kW PM motor the pay-back time would be 24 years. It is today not profitable to use PM motors for variable speed HVAC applications above 2 kW rated motor power. A further study is required to determine this limit in power rating more precisely. (orig.)

The impact of the provisions of the suspensions on the track of conveyor with suspended belt and distributed drive in violation of the power supply of the drives

Directory of Open Access Journals (Sweden)

Tolkachev E.N.

2017-12-01

Full Text Available The article is devoted to the topical issue, which is related to simulation of the failures of drives suspensions of the conveyor with suspended belt and distributed drive. Using the developed mathematical model of the failures drives suspensions due to the breakage of the electric circuit to the reference design of conveyor with suspended belt and distributed drive is performed modelling of dynamic characteristics. Investigation of the influence of the location of the failed drives suspensions on the track on the main technical characteristics of the conveyor belt with suspended belt was carried out.

INCREASING CONTROL’S EFFICIENCY FOR THE SHIP’S TWO-MASS ELECTRIC DRIVE

Directory of Open Access Journals (Sweden)

V.V. Budashko

2016-09-01

Full Text Available Purpose. For shipboard lifting and transporting machinery (LTM with AC thyristor electric drives (ED the problem of minimizing sway through the formation of the special law to change the principle of ED control over the lifting process is solved. Methodology. This goal was achieved through the following objectives: analysis of current studies on the reduction of the negative effects of load fluctuations, fixed on the suspension with variable parameters; determining the criteria to optimize the movement of the lifting mechanism and transfer control laws under which the load fluctuations are reduced; develop the methodology and experimental study of the main characteristics of the mobile model ED lifting mechanism with its load suspended from the perspective of both the parameterization of the control system (CS as well as elements of ED. For realization of tasks in research methods of mathematical modeling of dynamic processes on the computer, structural methods of control theory, experimental studies in the laboratory setting have been used. Results. Based on analysis of current research can be concluded that the stability of the ED of LTM to the disturbing points provided coincidence zero electric coordinates and speed deviation diametric plane of the vessel from the vertical position. Criteria for optimizing CS used by the ED LTM mathematical description of its dynamics differential equations to the estimated coefficients derived from the functions of state variables. The experimental dependence of dynamic equations of motion of an object under the influence of disturbing forces in the coordinate plane allowed to parameterize characteristic equation to the form, providing the solution to sustainability since the motor shaft of LTM. The functional circuit of CS eliminates the aperiodic components in the control in compliance with the criteria of sustainability and quality of transients by applying all-range regulator coordinate characteristics

Fault-tolerant electric drive and space-phasor modulation of flux-switching permanent magnet machine for aerospace application

NARCIS (Netherlands)

Wang, L.; Aleksandrov, S.; Tang, Y.; Paulides, J.J.H.; Lomonova, E.A.

2017-01-01

This study investigates how to improve the fault tolerance or availability of an electrical drive containing a three-phase 12 stator teeth/10 rotor poles (12/10) the flux-switching permanent magnet machine. In this respect, space-vector modulation and space-phasor modulation will be analysed in this

Impact of Different Driving Cycles and Operating Conditions on CO2 Emissions and Energy Management Strategies of a Euro-6 Hybrid Electric Vehicle

Directory of Open Access Journals (Sweden)

Claudio Cubito

2017-10-01

Full Text Available Although Hybrid Electric Vehicles (HEVs represent one of the key technologies to reduce CO2 emissions, their effective potential in real world driving conditions strongly depends on the performance of their Energy Management System (EMS and on its capability to maximize the efficiency of the powertrain in real life as well as during Type Approval (TA tests. Attempting to close the gap between TA and real world CO2 emissions, the European Commission has decided to introduce from September 2017 the Worldwide Harmonized Light duty Test Procedure (WLTP, replacing the previous procedure based on the New European Driving Cycle (NEDC. The aim of this work is the analysis of the impact of different driving cycles and operating conditions on CO2 emissions and on energy management strategies of a Euro-6 HEV through the limited number of information available from the chassis dyno tests. The vehicle was tested considering different initial battery State of Charge (SOC, ranging from 40% to 65%, and engine coolant temperatures, from −7 °C to 70 °C. The change of test conditions from NEDC to WLTP was shown to lead to a significant reduction of the electric drive and to about a 30% increase of CO2 emissions. However, since the specific energy demand of WLTP is about 50% higher than that of NEDC, these results demonstrate that the EMS strategies of the tested vehicle can achieve, in test conditions closer to real life, even higher efficiency levels than those that are currently evaluated on the NEDC, and prove the effectiveness of HEV technology to reduce CO2 emissions.

Alcohol effects on simulated driving performance and self-perceptions of impairment in DUI offenders.

Science.gov (United States)

Van Dyke, Nicholas; Fillmore, Mark T

2014-12-01

Drivers with a history of driving under the influence (DUI) of alcohol self-report heightened impulsivity and display reckless driving behaviors as indicated by increased rates of vehicle crashes, moving violations, and traffic tickets. Such poor behavioral self-regulation could also increase sensitivity to the disruptive effects of alcohol on driving performance. The present study examined the degree to which DUI drivers display an increased sensitivity to the acute impairing effects of alcohol on simulated driving performance and overestimate their driving fitness following alcohol consumption. Adult drivers with a history of DUI and a demographically matched group of drivers with no history of DUI (controls) were tested following a 0.65 g/kg alcohol and a placebo. Results indicated that alcohol impaired several measures of driving performance, and there was no difference between DUI offenders and controls in these impairments. However, following alcohol, DUI drivers self-reported a greater ability and willingness to drive compared with controls. These findings indicate that drivers with a history of DUI might perceive themselves as more fit to drive after drinking, which could play an important role in their decisions to drink and drive. PsycINFO Database Record (c) 2014 APA, all rights reserved.

Concerta cf Ritalin Effects on Driving Performance

Directory of Open Access Journals (Sweden)

J Gordon Millichap

2004-03-01

Full Text Available The effects of different methylphenidate (MPH delivery profiles on driving performance of 6 male ADHD adolescents, aged 16 to 19 years, were evaluated by a randomized, crossover, single-blind study comparing controlled-release (OROS MPH (Concerta given q.d. to immediate-release MPH (Ritalin in equal doses t.i.d. in a study at the University of Virginia, Charlottesville, VA.

Factors That Drive RTO Performance: An Overview. Synthesis Report

Science.gov (United States)

Misko, Josie

2017-01-01

This paper provides an overview of recent research on the factors that drive the performance of registered training organisations (RTOs), with a view to identifying areas for future research. Initially it explores the drivers of RTO performance; then discusses findings from available literature from Australia and from overseas, and discusses some…

The impact of Stereotype Threat on the simulated driving performance of older drivers.

Science.gov (United States)

Joanisse, Mélanie; Gagnon, Sylvain; Voloaca, Mihnea

2013-01-01

Older drivers are perceived as being dangerous and overly cautious by other drivers. We tested the hypothesis that this negative stereotype has a direct influence on the performance of older drivers. Based on the Stereotype Threat literature, we predicted that older driving performance would be altered after exposure to a Stereotype Threat. Sixty-one older drivers aged 65 and above completed a simulated driving assessment course. Prior to testing, half of the participants were told that the objective of the study was to investigate why older adults aged 65 and above were more implicated in on-road accidents (Stereotype Threat condition) and half were showed a neutral statement. Results confirmed that exposure to the threat significantly altered driving performance. Older adults in the Stereotype Threat condition made more driving mistakes than those in the control group. Interestingly, under a Stereotype Threat condition, older adults tended to commit more speeding infractions. We also observed that domain identification (whether driving is deemed important or not) moderated the impact of the threat. Taken together, these results support recent older drivers' performance models suggesting that the interaction between individual and social factors need to be considered when examining older drivers' performance. Copyright © 2012 Elsevier Ltd. All rights reserved.

Powertrain system for a hybrid electric vehicle

Science.gov (United States)

Reed, Jr., Richard G.; Boberg, Evan S.; Lawrie, Robert E.; Castaing, Francois J.

1999-08-31

A hybrid electric powertrain system is provided including an electric motor/generator drivingly engaged with the drive shaft of a transmission. The electric is utilized for synchronizing the rotation of the drive shaft with the driven shaft during gear shift operations. In addition, a mild hybrid concept is provided which utilizes a smaller electric motor than typical hybrid powertrain systems. Because the electric motor is drivingly engaged with the drive shaft of the transmission, the electric motor/generator is driven at high speed even when the vehicle speed is low so that the electric motor/generator provides more efficient regeneration.

Powertrain system for a hybrid electric vehicle

Science.gov (United States)

Reed, R.G. Jr.; Boberg, E.S.; Lawrie, R.E.; Castaing, F.J.

1999-08-31

A hybrid electric powertrain system is provided including an electric motor/generator drivingly engaged with the drive shaft of a transmission. The electric is utilized for synchronizing the rotation of the drive shaft with the driven shaft during gear shift operations. In addition, a mild hybrid concept is provided which utilizes a smaller electric motor than typical hybrid powertrain systems. Because the electric motor is drivingly engaged with the drive shaft of the transmission, the electric motor/generator is driven at high speed even when the vehicle speed is low so that the electric motor/generator provides more efficient regeneration. 34 figs.

PID and predictive control of electrical drives and power converters using MATLAB/Simulink

CERN Document Server

Wang, Liuping; Yoo, Dae; Gan, Lu; Ng, Ki

2015-01-01

A timely introduction to current research on PID and predictive control by one of the leading authors on the subject PID and Predictive Control of Electric Drives and Power Supplies using MATLAB/Simulink examines the classical control system strategies, such as PID control, feed-forward control and cascade control, which are widely used in current practice.  The authors share their experiences in actual design and implementation of the control systems on laboratory test-beds, taking the reader from the fundamentals through to more sophisticated design and analysis.    The book contains secti

How much do electric drive vehicles matter to future U.S. emissions?

Science.gov (United States)

Babaee, Samaneh; Nagpure, Ajay S; DeCarolis, Joseph F

2014-01-01

Hybrid, plug-in hybrid, and battery electric vehicles--known collectively as electric drive vehicles (EDVs)--may represent a clean and affordable option to meet growing U.S. light duty vehicle (LDV) demand. The goal of this study is 2-fold: identify the conditions under which EDVs achieve high LDV market penetration in the U.S. and quantify the associated change in CO2, SO2, and NOX emissions through midcentury. We employ the Integrated MARKAL-EFOM System (TIMES), a bottom-up energy system model, along with a U.S. data set developed for this analysis. To characterize EDV deployment through 2050, varying assumptions related to crude oil and natural gas prices, a CO2 policy, a federal renewable portfolio standard, and vehicle battery cost were combined to form 108 different scenarios. Across these scenarios, oil prices and battery cost have the biggest effect on EDV deployment. The model results do not demonstrate a clear and consistent trend toward lower system-wide emissions as EDV deployment increases. In addition to the trade-off between lower tailpipe and higher electric sector emissions associated with plug-in vehicles, the scenarios produce system-wide emissions effects that often mask the effect of EDV deployment.

Effects of alprazolam on driving ability, memory functioning and psychomotor performance: a randomized, placebo-controlled study.

Science.gov (United States)

Verster, Joris C; Volkerts, Edmund R; Verbaten, Marinus N

2002-08-01

Alprazolam is prescribed for the treatment of anxiety and panic disorder. Most users are presumably involved in daily activities such as driving. However, the effects of alprazolam on driving ability have never been investigated. This study was conducted to determine the effects of alprazolam (1 mg) on driving ability, memory and psychomotor performance. Twenty healthy volunteers participated in a randomized, double-blind, placebo-controlled crossover study. One hour after oral administration, subjects performed a standardized driving test on a primary highway during normal traffic. They were instructed to drive with a constant speed (90 km/h) while maintaining a steady lateral position within the right traffic lane. Primary performance measures were the Standard Deviation of Lateral Position (SDLP) and the Standard Deviation of Speed (SDS). After the driving test, subjective driving quality, mental effort, and mental activation during driving were assessed. A laboratory test battery was performed 2.5 h after treatment administration, comprising the Sternberg Memory Scanning Test, a Continuous Tracking Test, and a Divided Attention Test. Relative to placebo, alprazolam caused serious driving impairment, as expressed by a significantly increased SDLP (F(1,19) = 97.3, p driving quality (F(1,19) = 16.4, p driving (F(1,19) = 26.4, p drive an automobile or operate potentially dangerous machinery.

Comparison of real driving cycles and consumed braking power in suburban Slovakian driving

Directory of Open Access Journals (Sweden)

Gechev Tsvetomir

2017-01-01

Full Text Available The paper compares the features of suburban real driving cycles performed with CORRSYS DATRON measurement equipment on routes in the region of Žilina, Slovakia. It observes differences in the maximum and average vehicle velocities and the amount of braking in relation to the elevation profile of each individual cycle. Consumed braking power was also calculated in the different cycles in order to review the potential electricity regeneration capabilities of hybrid electric vehicles, operating on the same routes. The change in braking energy depending on vehicle mass and presence of grade on the routes in the measured cycles was also assessed. The calculations and plotting were done by using Matlab software.

Vehicle test report: Electric Vehicle Associates electric conversion of an AMC Pacer

Science.gov (United States)

Price, T. W.; Wirth, V. A., Jr.; Pompa, M. F.

1981-01-01

Tests were performed to characterize certain parameters of the EVA Pacer and to provide baseline data that can be used for the comparison of improved batteries that may be incorporated into the vehicle at a later time. The vehicle tests were concentrated on the electrical drive subsystem; i.e., the batteries, controller and motor. The tests included coastdowns to characterize the road load, and range evaluations for both cyclic and constant speed conditions. A qualitative evaluation of the vehicle's performance was made by comparing its constant speed range performance with other electric and hybrid vehicles. The Pacer performance was approximately equal to the majority of those vehicles assessed in 1977.

Performance Evaluation of A Developed Variable Frequency Drive ...

African Journals Online (AJOL)

This paper presents the performance characteristics of a developed variable frequency drive (VFD) adaptable for operation of ac machines speed control. The VFD developed is robust, durable, cheap and have low maintenance cost compared to conventional VFDs. The controlled asynchronous ac motor was operated to ...

Driving with music : Effects on arousal and performance

NARCIS (Netherlands)

Unal, Ayca Berfu; de Waard, Dick; Epstude, Kai; Steg, Linda

2013-01-01

In the current study, we aimed at exploring the influence of music on driving performance, arousal and mental effort while carrying out a monotonous car-following task in a low-complexity traffic setting. Participants (N = 47) were randomly assigned to loud and moderate volume music groups, and

Energy improvement and performance evaluation of a novel full hybrid electric motorcycle with power split e-CVT

International Nuclear Information System (INIS)

Chung, Cheng-Ta; Hung, Yi-Hsuan

2014-01-01

Highlights: • Innovative hybrid powertrain system using a planetary gearset and dual one-way clutch. • Three operation modes: EV-mode, engine-driven mode and power split e-CVT mode. • Outstanding energy improvement (max. 32+%) compared to traditional vehicles. • Experimentally implemented for light-duty vehicles in the near future. - Abstract: The power split electronic-continuously variable transmission (e-CVT) has been globally accepted as a main architecture for developing a hybrid electric vehicle (HEV). In this paper, a novel full hybrid electric motorcycle with power split e-CVT is proposed. It consists of an engine, a reversible generator, a reversible driving motor, a set of the planetary gear, two one-way clutches, and transmission components arranged for a planetary gearset and dual one-way clutch transmission (PDOC). Three operation modes were properly switched for optimal output dynamics: EV-mode, engine-driven mode, and power split e-CVT mode. Performance simulation compared with that of a baseline system using the conventional rubber-belt CVT is conducted to evaluate its feasibility and potential. The results present superior driving performance and fuel economy for the proposed motorcycle (maximum 32% fuel economy improvement) and thus offer a favorable support for further development

Assessment of Joystick control during the performance of powered wheelchair driving tasks

Directory of Open Access Journals (Sweden)

Routhier François

2011-05-01

Full Text Available Abstract Background Powered wheelchairs are essential for many individuals who have mobility impairments. Nevertheless, if operated improperly, the powered wheelchair poses dangers to both the user and to those in its vicinity. Thus, operating a powered wheelchair with some degree of proficiency is important for safety, and measuring driving skills becomes an important issue to address. The objective of this study was to explore the discriminate validity of outcome measures of driving skills based on joystick control strategies and performance recorded using a data logging system. Methods We compared joystick control strategies and performance during standardized driving tasks between a group of 10 expert and 13 novice powered wheelchair users. Driving tasks were drawn from the Wheelchair Skills Test (v. 4.1. Data from the joystick controller were collected on a data logging system. Joystick control strategies and performance outcome measures included the mean number of joystick movements, time required to complete tasks, as well as variability of joystick direction. Results In simpler tasks, the expert group's driving skills were comparable to those of the novice group. Yet, in more difficult and spatially confined tasks, the expert group required fewer joystick movements for task completion. In some cases, experts also completed tasks in approximately half the time with respect to the novice group. Conclusions The analysis of joystick control made it possible to discriminate between novice and expert powered wheelchair users in a variety of driving tasks. These results imply that in spatially confined areas, a greater powered wheelchair driving skill level is required to complete tasks efficiently. Based on these findings, it would appear that the use of joystick signal analysis constitutes an objective tool for the measurement of powered wheelchair driving skills. This tool may be useful for the clinical assessment and training of powered

The effects of practice with MP3 players on driving performance.

Science.gov (United States)

Chisholm, S L; Caird, J K; Lockhart, J

2008-03-01

This study examined the effects of repeated iPod interactions on driver performance to determine if performance decrements decreased with practice. Nineteen younger drivers (mean age=19.4, range 18-22) participated in a seven session study in the University of Calgary Driving Simulator (UCDS). Drivers encountered a number of critical events on the roadways while interacting with an iPod including a pedestrian entering the roadway, a vehicle pullout, and a lead vehicle braking. Measures of hazard response, vehicle control, eye movements, and secondary task performance were analyzed. Increases in perception response time (PRT) and collisions were found while drivers were performing the difficult iPod tasks, which involved finding a specific song within the song titles menu. Over the course of the six experimental sessions, driving performance improved in all conditions. Difficult iPod interactions significantly increased the amount of visual attention directed into the vehicle above that of the baseline condition. With practice, slowed responses to driving hazards while interacting with the iPod declined somewhat, but a decrement still remained relative to the baseline condition. The multivariate results suggest that access to difficult iPod tasks while vehicles are in motion should be curtailed.

Resonance reduction for AC drives with small capacitance in the DC link

DEFF Research Database (Denmark)

Máthé, Lászlo; Török, Lajos; Wang, Dong

2016-01-01

Pulse Width Modulated AC drives equipped with small DC-link capacitor are becoming an attractive solution for electric drive applications with moderate requirements for shaft dynamic performance. However, when these drives are fed from a weak grid a resonance between the line side impedance...... and the DC-link capacitor appears. Due to this resonance, the THD and the partially weighted harmonic distortion of the line currents are increased, which may rise compatibility problems with the AC line harmonic standards. By using vector control the motor drive is transformed into a constant power load...

Advanced Electrical Machines and Machine-Based Systems for Electric and Hybrid Vehicles

Directory of Open Access Journals (Sweden)

Ming Cheng

2015-09-01

Full Text Available The paper presents a number of advanced solutions on electric machines and machine-based systems for the powertrain of electric vehicles (EVs. Two types of systems are considered, namely the drive systems designated to the EV propulsion and the power split devices utilized in the popular series-parallel hybrid electric vehicle architecture. After reviewing the main requirements for the electric drive systems, the paper illustrates advanced electric machine topologies, including a stator permanent magnet (stator-PM motor, a hybrid-excitation motor, a flux memory motor and a redundant motor structure. Then, it illustrates advanced electric drive systems, such as the magnetic-geared in-wheel drive and the integrated starter generator (ISG. Finally, three machine-based implementations of the power split devices are expounded, built up around the dual-rotor PM machine, the dual-stator PM brushless machine and the magnetic-geared dual-rotor machine. As a conclusion, the development trends in the field of electric machines and machine-based systems for EVs are summarized.

Effects of age and auditory and visual dual tasks on closed-road driving performance.

Science.gov (United States)

Chaparro, Alex; Wood, Joanne M; Carberry, Trent

2005-08-01

This study investigated how driving performance of young and old participants is affected by visual and auditory secondary tasks on a closed driving course. Twenty-eight participants comprising two age groups (younger, mean age = 27.3 years; older, mean age = 69.2 years) drove around a 5.1-km closed-road circuit under both single and dual task conditions. Measures of driving performance included detection and identification of road signs, detection and avoidance of large low-contrast road hazards, gap judgment, lane keeping, and time to complete the course. The dual task required participants to verbally report the sums of pairs of single-digit numbers presented through either a computer speaker (auditorily) or a dashboard-mounted monitor (visually) while driving. Participants also completed a vision and cognitive screening battery, including LogMAR visual acuity, Pelli-Robson letter contrast sensitivity, the Trails test, and the Digit Symbol Substitution (DSS) test. Drivers reported significantly fewer signs, hit more road hazards, misjudged more gaps, and increased their time to complete the course under the dual task (visual and auditory) conditions compared with the single task condition. The older participants also reported significantly fewer road signs and drove significantly more slowly than the younger participants, and this was exacerbated for the visual dual task condition. The results of the regression analysis revealed that cognitive aging (measured by the DSS and Trails test) rather than chronologic age was a better predictor of the declines seen in driving performance under dual task conditions. An overall z score was calculated, which took into account both driving and the secondary task (summing) performance under the two dual task conditions. Performance was significantly worse for the auditory dual task compared with the visual dual task, and the older participants performed significantly worse than the young subjects. These findings demonstrate

Power Electronics and Electric Machines | Transportation Research | NREL

Science.gov (United States)

Power Electronics and Electric Machines NREL's power electronics and electric machines research helping boost the performance of power electronics components and systems, while driving down size, weight technical barriers to EDV commercialization. EDVs rely heavily on power electronics to distribute the proper

Reduce consumption, improve production. Electronic adjustable speed drives and high performance motors; Consommez moins, produisez mieux. Variateurs electroniques de vitesse et moteurs performants