WorldWideScience

Sample records for performance cost weight

  1. Computerized systems analysis and optimization of aircraft engine performance, weight, and life cycle costs

    Science.gov (United States)

    Fishbach, L. H.

    1979-01-01

    The computational techniques utilized to determine the optimum propulsion systems for future aircraft applications and to identify system tradeoffs and technology requirements are described. The characteristics and use of the following computer codes are discussed: (1) NNEP - a very general cycle analysis code that can assemble an arbitrary matrix fans, turbines, ducts, shafts, etc., into a complete gas turbine engine and compute on- and off-design thermodynamic performance; (2) WATE - a preliminary design procedure for calculating engine weight using the component characteristics determined by NNEP; (3) POD DRG - a table look-up program to calculate wave and friction drag of nacelles; (4) LIFCYC - a computer code developed to calculate life cycle costs of engines based on the output from WATE; and (5) INSTAL - a computer code developed to calculate installation effects, inlet performance and inlet weight. Examples are given to illustrate how these computer techniques can be applied to analyze and optimize propulsion system fuel consumption, weight, and cost for representative types of aircraft and missions.

  2. Low-cost, low-weight CNG cylinder development. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Richards, Mark E.; Melford, K.; Wong, J.; Gambone, L.

    1999-09-01

    This program was established to develop and commercialize new high-strength steel-lined, composite hoop-wrapped compressed natural gas (CNG) cylinders for vehicular applications. As much as 70% of the cost of natural gas vehicles can be related to on-board natural gas storage costs. The cost and weight targets for this program represent significant savings in each characteristic when compared to comparable containers available at the initiation of the program. The program objectives were to optimize specific weight and cost goals, yielding CNG cylinders with dimensions that should, allowing for minor modifications, satisfy several vehicle market segments. The optimization process encompassed material, design, and process improvement. In optimizing the CNG cylinder design, due consideration was given to safety aspects relative to national, international, and vehicle manufacturer cylinder standards and requirements. The report details the design and development effort, encompassing plant modifications, material selection, design issues, tooling development, prototype development, and prototype testing. Extenuating circumstances prevented the immediate commercialization of the cylinder designs, though significant progress was made towards improving the cost and performance of CNG cylinders. A new low-cost fiber was successfully employed while the weight target was met and the cost target was missed by less than seven percent.

  3. Cost-effectiveness of sibutramine in the LOSE Weight Study: evaluating the role of pharmacologic weight-loss therapy within a weight management program.

    Science.gov (United States)

    Malone, Daniel C; Raebel, Marsha A; Porter, Julie A; Lanty, Frances A; Conner, Douglas A; Gay, Elizabeth C; Merenich, John A; Vogel, Erin A

    2005-01-01

    the cost-effectiveness of drug therapy when used in conjunction with a weight management program (WMP) for treatment of obesity. The objective was to compare the cost-effectiveness of sibutramine (Meridia) plus a structured WMP versus only a structured WMP in both overweight and obese individuals. The core WMP was a physician-supervised, multidisciplinary program for which each enrollee paid $100 out of pocket. A cost-effectiveness analysis was performed based upon the results of a previously published randomized controlled trial conducted within a managed care organization. The target population for this study was obese or overweight persons. The perspective of the study was that of a managed care organization. The intervention consisted of subjects receiving a WMP with or without sibutramine. The primary outcomes of this study were (a) absolute change in body weight and percentage change in body weight over 12 months, (b) change in obesity-related and total medical costs from 12 months prior to enrollment through 12 months after enrollment, and (c) cost-effectiveness in terms of cost per pound of weight loss. All costs were adjusted to 2004 dollars using the respective components of the consumer price index for each medical service or medication. A total of 501 evaluable subjects were enrolled in the study, with 281 receiving sibutramine plus a structured WMP and 220 receiving only the structured WMP. The meanSD weight loss was significantly greater in the sibutramine (13.715.5 pounds, 4.8%) group than in the nondrug group (513.2 pounds, 2.2%) (P cost was a median increase of $408 for the sibutramine group compared with $31 for the nondrug group (P cost was a median $1,279 increase in the sibutramine group compared with $271 for the nondrug group (P cost by $44 per additional pound of weight loss (95% confidence interval, 42-46). Sensitivity analyses found that the results were sensitive to the price of sibutramine, whereas varying the cost of clinic visits did

  4. Weight and cost forecasting for advanced manned space vehicles

    Science.gov (United States)

    Williams, Raymond

    1989-01-01

    A mass and cost estimating computerized methology for predicting advanced manned space vehicle weights and costs was developed. The user friendly methology designated MERCER (Mass Estimating Relationship/Cost Estimating Relationship) organizes the predictive process according to major vehicle subsystem levels. Design, development, test, evaluation, and flight hardware cost forecasting is treated by the study. This methodology consists of a complete set of mass estimating relationships (MERs) which serve as the control components for the model and cost estimating relationships (CERs) which use MER output as input. To develop this model, numerous MER and CER studies were surveyed and modified where required. Additionally, relationships were regressed from raw data to accommodate the methology. The models and formulations which estimated the cost of historical vehicles to within 20 percent of the actual cost were selected. The result of the research, along with components of the MERCER Program, are reported. On the basis of the analysis, the following conclusions were established: (1) The cost of a spacecraft is best estimated by summing the cost of individual subsystems; (2) No one cost equation can be used for forecasting the cost of all spacecraft; (3) Spacecraft cost is highly correlated with its mass; (4) No study surveyed contained sufficient formulations to autonomously forecast the cost and weight of the entire advanced manned vehicle spacecraft program; (5) No user friendly program was found that linked MERs with CERs to produce spacecraft cost; and (6) The group accumulation weight estimation method (summing the estimated weights of the various subsystems) proved to be a useful method for finding total weight and cost of a spacecraft.

  5. Intensive treatment for adults with anorexia nervosa: The cost of weight restoration.

    Science.gov (United States)

    Guarda, Angela S; Schreyer, Colleen C; Fischer, Laura K; Hansen, Jennifer L; Coughlin, Janelle W; Kaminsky, Michael J; Attia, Evelyn; Redgrave, Graham W

    2017-03-01

    Weight restoration in anorexia nervosa (AN) is associated with lower relapse risk; however rate of weight gain and percent of patients achieving weight restoration (BMI ≥ 19 at discharge) vary among treatment programs. We compared both cost/pound of weight gained and cost of weight restoration in a hospital-based inpatient (IP)-partial hospitalization (PH) eating disorders program to estimates of these costs for residential treatment. All adult first admissions to the IP-PH program with AN (N = 314) from 2003 to 2015 were included. Cost of care was based on hospital charges, rates of weight gain, and weight restoration data. Results were compared with residential treatment costs extracted from a national insurance claims database and published weight gain data. Average charge/day in the IP-PH program was $2295 for IP and $1567 for PH, yielding an average cost/pound gained of $4089 and $7050, respectively, with 70% of patients achieving weight restoration. Based on published mean weight gain data and conservative cost/day estimates, residential treatment is associated with higher cost/pound, and both higher cost and lower likelihood of weight restoration for most patients. The key metrics used in this study are recommended for comparing the cost-effectiveness of intensive treatment programs for patients with AN. © 2017 Wiley Periodicals, Inc.

  6. Effect of housing, initial weight and season on feedlot performance ...

    African Journals Online (AJOL)

    Feedlot information, submitted by Iowa cattle producers to the Iowa State University Feedlot Performance and Cost Monitoring Program, was examined to determine the effects of housing, initial weight and season interactions on beef steer performance. Feedlot information, consisting of 1225 pens of steers, contained ...

  7. Investigating DRG cost weights for hospitals in middle income countries.

    Science.gov (United States)

    Ghaffari, Shahram; Doran, Christopher; Wilson, Andrew; Aisbett, Chris; Jackson, Terri

    2009-01-01

    Identifying the cost of hospital outputs, particularly acute inpatients measured by Diagnosis Related Groups (DRGs), is an important component of casemix implementation. Measuring the relative costliness of specific DRGs is useful for a wide range of policy and planning applications. Estimating the relative use of resources per DRG can be done through different costing approaches depending on availability of information and time and budget. This study aims to guide costing efforts in Iran and other countries in the region that are pursuing casemix funding, through identifying the main issues facing cost finding approaches and introducing the costing models compatible with their hospitals accounting and management structures. The results show that inadequate financial and utilisation information at the patient's level, poorly computerized 'feeder systems'; and low quality data make it impossible to estimate reliable DRGs costs through clinical costing. A cost modelling approach estimates the average cost of 2.723 million Rials (Iranian Currency) per DRG. Using standard linear regression, a coefficient of 0.14 (CI = 0.12-0.16) suggests that the average cost weight increases by 14% for every one-day increase in average length of stay (LOS).We concluded that calculation of DRG cost weights (CWs) using Australian service weights provides a sensible starting place for DRG-based hospital management; but restructuring hospital accounting systems, designing computerized feeder systems, using appropriate software, and development of national service weights that reflect local practice patterns will enhance the accuracy of DRG CWs.

  8. Costs and expected gain in lifetime health from intensive care versus general ward care of 30,712 individual patients: a distribution-weighted cost-effectiveness analysis.

    Science.gov (United States)

    Lindemark, Frode; Haaland, Øystein A; Kvåle, Reidar; Flaatten, Hans; Norheim, Ole F; Johansson, Kjell A

    2017-08-21

    Clinicians, hospital managers, policy makers, and researchers are concerned about high costs, increased demand, and variation in priorities in the intensive care unit (ICU). The objectives of this modelling study are to describe the extra costs and expected health gains associated with admission to the ICU versus the general ward for 30,712 patients and the variation in cost-effectiveness estimates among subgroups and individuals, and to perform a distribution-weighted economic evaluation incorporating extra weighting to patients with high severity of disease. We used a decision-analytic model that estimates the incremental cost per quality-adjusted life year (QALY) gained (ICER) from ICU admission compared with general ward care using Norwegian registry data from 2008 to 2010. We assigned increasing weights to health gains for those with higher severity of disease, defined as less expected lifetime health if not admitted. The study has inherent uncertainty of findings because a randomized clinical trial comparing patients admitted or rejected to the ICU has never been performed. Uncertainty is explored in probabilistic sensitivity analysis. The mean cost-effectiveness of ICU admission versus ward care was €11,600/QALY, with 1.6 QALYs gained and an incremental cost of €18,700 per patient. The probability (p) of cost-effectiveness was 95% at a threshold of €22,000/QALY. The mean ICER for medical admissions was €10,700/QALY (p = 97%), €12,300/QALY (p = 93%) for admissions after acute surgery, and €14,700/QALY (p = 84%) after planned surgery. For individualized ICERs, there was a 50% probability that ICU admission was cost-effective for 85% of the patients at a threshold of €64,000/QALY, leaving 15% of the admissions not cost-effective. In the distributional evaluation, 8% of all patients had distribution-weighted ICERs (higher weights to gains for more severe conditions) above €64,000/QALY. High-severity admissions gained the most, and were more

  9. Designing for psychological change: individuals' reward and cost valuations in weight management.

    Science.gov (United States)

    Hsu, Anne; Blandford, Ann

    2014-06-26

    Knowledge of the psychological constructs that underlie behavior offers valuable design opportunities for persuasive systems. We use the decision theory, which describes how behavior is underpinned by reward-cost valuations, as a framework for investigating such psychological constructs to deliver design objectives for weight management technologies. We applied a decision theory-based analysis in the domain of weight management to understand the rewards and costs that surround individuals' weight management behaviors, with the aim of uncovering design opportunities for weight management technologies. We conducted qualitative interviews with 15 participants who were or had been trying to lose weight. Thematic analysis was used to extract themes that covered the rewards and costs surrounding weight management behaviors. We supplemented our qualitative study with a quantitative survey of 100 respondents investigating the extent to which they agreed with statements reflecting themes from the qualitative study. The primary obstacles to weight management were the rewards associated with unhealthy choices, such as the pleasures of unhealthy foods and unrestricted consumption in social situations, and the significant efforts required to change habits, plan, and exercise. Psychological constructs that supported positive weight management included feeling good after making healthy choices, being good to oneself, experiencing healthy yet still delicious foods, and receiving social support and encouraging messages (although opinions about encouraging messages was mixed). A rewards-costs driven enquiry revealed a wide range of psychological constructs that contribute to discouraging and supporting weight management. The constructs extracted from our qualitative study were verified by our quantitative survey, in which the majority of respondents also reported similar thoughts and feelings. This understanding of the rewards and costs surrounding weight management offers a range

  10. Equity weighting and the marginal damage costs of climate change

    Energy Technology Data Exchange (ETDEWEB)

    Anthoff, David [The Economic and Social Research Institute, Dublin (Ireland)]|[International Max Planck Research School on Earth System Modelling, Hamburg (Germany)]|[Research Unit Sustainability and Global Change, Hamburg University and Centre for Marine and Atmospheric Science, Hamburg (Germany); Hepburn, Cameron [Smith School of Enterprise and the Environment, and James Martin Institute, Said Business School, University of Oxford, and New College, Oxford (United Kingdom); Tol, Richard S.J. [The Economic and Social Research Institute, Dublin (Ireland)]|[Research Unit Sustainability and Global Change, Hamburg University and Centre for Marine and Atmospheric Science, Hamburg (Germany)]|[Institute for Environmental Studies, Vrije Universiteit, Amsterdam (Netherlands)]|[Engineering and Public Policy, Carnegie Mellon University, Pittsburgh, PA (United States)

    2009-01-15

    Climate change will give rise to different impacts in different countries, and different countries have different levels of development. Equity-weighted estimates of the (marginal) impact of greenhouse gas emissions reflect these differences. This paper analyses the impact of equity weighting on the marginal damage cost of carbon dioxide emissions, and reaches four main conclusions. First, equity-weighted estimates are substantially higher than estimates without equity-weights; equity-weights may even change the sign of the social cost estimates. Second, estimates differ by two orders of magnitude depending on the region to which the equity weights are normalised. Third, equity-weighted estimates are sensitive to the resolution of the impact estimates. Depending on the assumed intra-regional income distribution, estimates may be more than twice as high if national rather than regional impacts are aggregated. Fourth, variations in the assumed inequality aversion have different impacts in different scenarios, not only because different scenarios have different emissions and hence warming, but also because different scenarios have different income differences, different growth rates, and different vulnerabilities. (author)

  11. Equity weighting and the marginal damage costs of climate change

    International Nuclear Information System (INIS)

    Anthoff, David; Hepburn, Cameron; Tol, Richard S.J.

    2009-01-01

    Climate change will give rise to different impacts in different countries, and different countries have different levels of development. Equity-weighted estimates of the (marginal) impact of greenhouse gas emissions reflect these differences. This paper analyses the impact of equity weighting on the marginal damage cost of carbon dioxide emissions, and reaches four main conclusions. First, equity-weighted estimates are substantially higher than estimates without equity-weights; equity-weights may even change the sign of the social cost estimates. Second, estimates differ by two orders of magnitude depending on the region to which the equity weights are normalised. Third, equity-weighted estimates are sensitive to the resolution of the impact estimates. Depending on the assumed intra-regional income distribution, estimates may be more than twice as high if national rather than regional impacts are aggregated. Fourth, variations in the assumed inequality aversion have different impacts in different scenarios, not only because different scenarios have different emissions and hence warming, but also because different scenarios have different income differences, different growth rates, and different vulnerabilities. (author)

  12. Predictive Engineering Tools for Injection-Molded Long-Carbon-Thermoplastic Composites: Weight and Cost Analyses

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Ba Nghiep [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Fifield, Leonard S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Gandhi, Umesh N. [Toyota Research Inst. North America, Ann Arbor, MI (United States); Mori, Steven [MAGNA Exteriors and Interiors Corporation, Aurora, ON (Canada); Wollan, Eric J. [PlastiComp, Inc., Winona, MN (United States)

    2016-08-01

    This project proposed to integrate, optimize and validate the fiber orientation and length distribution models previously developed and implemented in the Autodesk Simulation Moldflow Insight (ASMI) package for injection-molded long-carbon-fiber thermoplastic composites into a cohesive prediction capability. The current effort focused on rendering the developed models more robust and efficient for automotive industry part design to enable weight savings and cost reduction. The project goal has been achieved by optimizing the developed models, improving and integrating their implementations in ASMI, and validating them for a complex 3D LCF thermoplastic automotive part (Figure 1). Both PP and PA66 were used as resin matrices. After validating ASMI predictions for fiber orientation and fiber length for this complex part against the corresponding measured data, in collaborations with Toyota and Magna PNNL developed a method using the predictive engineering tool to assess LCF/PA66 complex part design in terms of stiffness performance. Structural three-point bending analyses of the complex part and similar parts in steel were then performed for this purpose, and the team has then demonstrated the use of stiffness-based complex part design assessment to evaluate weight savings relative to the body system target (≥ 35%) set in Table 2 of DE-FOA-0000648 (AOI #1). In addition, starting from the part-to-part analysis, the PE tools enabled an estimated weight reduction for the vehicle body system using 50 wt% LCF/PA66 parts relative to the current steel system. Also, from this analysis an estimate of the manufacturing cost including the material cost for making the equivalent part in steel has been determined and compared to the costs for making the LCF/PA66 part to determine the cost per “saved” pound.

  13. Discount rates, equity weights and the social cost of carbon

    International Nuclear Information System (INIS)

    Hope, Chris

    2008-01-01

    Equity weighting has been proposed as a way of allowing welfare equivalents to be included in the social cost of carbon since a dollar to a poor person is worth more than a dollar to a rich one. Here we use the PAGE2002 integrated assessment model to show that the social cost of carbon is higher without equity weights (an elasticity of marginal utility with respect to income of 0) than with them. This might seem counter-intuitive, but it comes about because of the logical link between equity weights and discount rates; as the elasticity goes from 0 to - 0.5 to - 1.0, the social rate of time preference rises, and the drop in present values that results far outweighs the small increase in impacts that equity weights bring. (author)

  14. Associations of recent weight loss with health care costs and utilization among older women.

    Directory of Open Access Journals (Sweden)

    John T Schousboe

    Full Text Available The association of weight loss with health care costs among older women is uncertain. Our study aim was to examine the association of objectively measured weight change with subsequent total health care (THC costs and other health care utilization among older women. Our study population included 2,083 women (mean age 80.2 years enrolled in the Study of Osteoporotic Fractures and U.S. Medicare Fee for Service. Weight loss and gain were defined, respectively, as ≥5% decrease and ≥5% increase in body weight, and weight maintenance as <5% change in body weight over a period of 4.5 years. THC costs, outpatient costs, hospitalizations, and skilled nursing facility [SNF] utilization were estimated from Medicare claims for 1 year after the period during which weight change was measured. The associations of weight change with THC and outpatient costs were estimated using generalized linear models with gamma variance and log link functions, and with hospitalizations and SNF utilization using logistic models. Adjusted for age and current body mass index (BMI, weight loss compared with weight maintenance was associated with a 35% increase in THC costs ($2148 [95% CI, 745 to 3552], 2014 U.S. dollars, a 15% increase in outpatient costs ($329 [95% C.I. -1 to 660], and odds ratios of 1.42 (95% CI, 1.14 to 1.76 for ≥1 hospital stay and 1.45 (95% CI, 1.03 to 2.03 for ≥1 SNF stay. These associations did not vary by BMI category. After additional adjustment for multi-morbidity and functional status, associations of weight loss with all four outcomes were no longer significant. In conclusion, ≥5% weight loss among older women is not associated with increased THC and outpatient costs, hospitalization, and SNF utilization, irrespective of BMI category after accounting for multi-morbidity and impaired functional status that accompany weight loss.

  15. Effects of independently altering body weight and body mass on the metabolic cost of running.

    Science.gov (United States)

    Teunissen, Lennart P J; Grabowski, Alena; Kram, Rodger

    2007-12-01

    The metabolic cost of running is substantial, despite the savings from elastic energy storage and return. Previous studies suggest that generating vertical force to support body weight and horizontal forces to brake and propel body mass are the major determinants of the metabolic cost of running. In the present study, we investigated how independently altering body weight and body mass affects the metabolic cost of running. Based on previous studies, we hypothesized that reducing body weight would decrease metabolic rate proportionally, and adding mass and weight would increase metabolic rate proportionally. Further, because previous studies show that adding mass alone does not affect the forces generated on the ground, we hypothesized that adding mass alone would have no substantial effect on metabolic rate. We manipulated the body weight and body mass of 10 recreational human runners and measured their metabolic rates while they ran at 3 m s(-1). We reduced weight using a harness system, increased mass and weight using lead worn about the waist, and increased mass alone using a combination of weight support and added load. We found that net metabolic rate decreased in less than direct proportion to reduced body weight, increased in slightly more than direct proportion to added load (added mass and weight), and was not substantially different from normal running with added mass alone. Adding mass alone was not an effective method for determining the metabolic cost attributable to braking/propelling body mass. Runners loaded with mass alone did not generate greater vertical or horizontal impulses and their metabolic costs did not substantially differ from those of normal running. Our results show that generating force to support body weight is the primary determinant of the metabolic cost of running. Extrapolating our reduced weight data to zero weight suggests that supporting body weight comprises at most 74% of the net cost of running. However, 74% is probably an

  16. The effect of simulating weight gain on the energy cost of walking in unimpaired children and children with cerebral palsy.

    Science.gov (United States)

    Plasschaert, Frank; Jones, Kim; Forward, Malcolm

    2008-12-01

    To examine the effect of simulating weight gain on the energy cost of walking in children with cerebral palsy (CP) compared with unimpaired children. Repeated measures, matched subjects, controlled. University hospital clinical gait and movement analysis laboratory. Children (n=42) with CP and unimpaired children (n=42). Addition of 10% of body mass in weight belt. Energy cost of walking parameters consisting of walking speed, Physiological Cost Index, Total Heart Beat Index, oxygen uptake (VO2), gross oxygen cost, nondimensional net oxygen cost, and net oxygen cost with speed normalized to height were measured by using a breath-by-breath gas analysis system (K4b2) and a light beam timing gate system arranged around a figure 8 track. Two walking trials were performed in random order, with and the other without wearing a weighted belt. Children with CP and their unimpaired counterparts responded in fundamentally different ways to weight gain. The unimpaired population maintained speed and VO2 but the children with CP trended toward a drop in their speed and an increase in their VO2. The oxygen consumption of children with CP showed a greater dependence on mass than the unimpaired group (P=.043). An increase of a relatively small percentage in body mass began to significantly impact the energy cost of walking in children with CP. This result highlights the need for weight control to sustain the level of functional walking in these children.

  17. A seismic performance and cost comparison of top and bottom supported liquid metal reactor vessels

    International Nuclear Information System (INIS)

    Carlson, T.M.; Kiciman, O.K.; Petrozelli, J.F.

    1989-01-01

    It is the premise of this paper that the revision of a pool LMR from a TSRV configuration to a specific bottom supported reactor vessel (BSRV) configuration can resolve the above TSRV disadvantages related to load path length and diversity, thereby improving seismic performance and simultaneously reducing RV block costs by reducing weights. This paper demonstrates this premise by comparing a reference TSRV block with a specific BSRV block design. Recent capital cost estimates ($/kWe) for U.S. liquid metal reactor (LMR) plant designs reveal that the balance of plant costs could be reduced below that of the balance of plant costs for a comparable light water reactor plant. However, in regions of high seismicity, non-seismically isolated LMR nuclear steam supply system weights are costs per kWe are two to three times the weights and costs of light water reactor nuclear steam supply systems. While all portions of the LMR nuclear steam supply system require examination for potential cost reductions, the focus of this paper is the reactor vessel (RV) block for a large pool plant

  18. A randomized controlled trial testing an Internet delivered cost-benefit approach to weight loss maintenance.

    Science.gov (United States)

    Leahey, Tricia M; Fava, Joseph L; Seiden, Andrew; Fernandes, Denise; Doyle, Caroline; Kent, Kimberly; La Rue, Molly; Mitchell, Marc; Wing, Rena R

    2016-11-01

    Weight loss maintenance is a significant challenge in obesity treatment. During maintenance the "costs" of adhering to weight management behaviors may outweigh the "benefits." This study examined the efficacy of a novel approach to weight loss maintenance based on modifying the cost-benefit ratio. Individuals who achieved a 5% weight loss (N=75) were randomized to one of three, 10-month maintenance interventions. All interventions were delivered primarily via the Internet. The Standard arm received traditional weight maintenance strategies. To increase benefits, or rewards, for maintenance behaviors, the two cost-benefit intervention conditions received weekly monetary rewards for self-monitoring and social reinforcement via e-coaching. To decrease behavioral costs (boredom) and increase novelty, participants in the cost-benefit conditions also monitored different evidence-based behaviors every two weeks (e.g., Weeks 1 & 2: steps; Week 3 & 4: red foods). The primary difference between the cost-benefit interventions was type of e-coach providing social reinforcement: Professional (CB Pro) or Peer (CB Peer). Study procedures took place in Providence, RI from 2013 to 2014. Retention was 99%. There were significant group differences in weight regain (p=.01). The Standard arm gained 3.5±5.7kg. In contrast, participants in CB Pro and CB Peer lost an additional 1.8±7.0kg and 0.5±6.4kg, respectively. These results suggest that an Internet delivered cost-benefit approach to weight loss maintenance may be effective for long-term weight control. In addition, using peer coaches to provide reinforcement may be a particularly economic alternative to professionals. These data are promising and provide support for a larger, longer trial. Copyright © 2016 Elsevier Inc. All rights reserved.

  19. Cost reduction in abdominal CT by weight-adjusted dose.

    Science.gov (United States)

    Arana, Estanislao; Martí-Bonmatí, Luis; Tobarra, Eva; Sierra, Consuelo

    2009-06-01

    To analyze the influence of contrast dose adjusted by weight vs. fixed contrast dose in the attenuation and cost of abdominal computed tomography (CT). A randomised, consecutive, parallel group study was conducted in 151 patients (74 men and 77 women, age range 22-67 years), studied with the same CT helical protocol. A dose at 1.75 ml/kg was administered in 101 patients while 50 patients had a fixed dose of 120 ml of same non-ionic contrast material (320 mg/ml). Mean enhancements were measured at right hepatic lobe, superior abdominal aorta and inferior cava vein. Statistical analysis was weight-stratified (81 kg). Aortic attenuation was significantly superior (p61 kg in dose-adjusted group, presented higher hepatic attenuation, being statistically significant in those >81 kg (p80 kg, there was an over cost of euro 10.7 per patient. An injection volume of 1.75 ml/kg offers an optimal diagnostic quality with a global savings of euro 1.34 per patient.

  20. Environmental costs and resource planning consequences: New England electric's rating and weighting approach

    International Nuclear Information System (INIS)

    Destribats, A.F.; Hutchinson, M.A.; Stout, T.M.; White, D.S.

    1990-01-01

    In mid 1989, the New England Electric System (NEES or Company) began an effort to reflect the potential environmental externalities of new resources in its long range planning process. Having examined several methods for incorporating externalities, including cost of control, the Company adopted a rating and weighting approach. Not strictly quantitative nor qualitative, the rating and weighting approach provided a means to apply an environmental score to all new resources considered for the Company's long range resource plan, NEESPLAN 1990. A maximum environmental cost penalty of fifteen percent was applied to the resource considered for inclusion in the plan that posed the highest amount of potential environmental degradation. All other resources received a smaller penalty that was based on the ratio of their environmental score to the highest score. Application of this penalty tended to improve the cost-effectiveness of demand-side programs and worsen some supply-side options' cost-effectiveness. Both the rating and weighting approach employed by NEES and its application in the long range planning process have been the subject of several critical reviews. Having stated that the advantages of the rating and weighting approach include its easy reviewability and flexibility to be modified as better information becomes available, the Company has subsequently revised the approach to address the comments made by reviewers. The purpose of this paper is to describe the rating and weighting approach, its recent revisions, and the effect of the revised methodology on the Company's long range resource plan

  1. Post-weaning and whole-of-life performance of pigs is determined by live weight at weaning and the complexity of the diet fed after weaning

    Directory of Open Access Journals (Sweden)

    Cherie L. Collins

    2017-12-01

    Full Text Available The production performance and financial outcomes associated with weaner diet complexity for pigs of different weight classes at weaning were examined in this experiment. A total of 720 weaner pigs (360 entire males and 360 females were selected at weaning (27 ± 3 d and allocated to pens of 10 based on individual weaning weight (light weaning weight: pigs below 6.5 kg; medium weaning weight: 6.5 to 8 kg; heavy weaning weight: above 8.5 kg. Pens were then allocated in a 3 × 2 × 2 factorial arrangement of treatments with the respective factors being weaning weight (heavy, medium and light; H, M and L, respectively, weaner diet complexity (high complexity/cost, HC; low complexity/cost, LC, and gender (male and female. Common diets were fed to both treatment groups during the final 4 weeks of the weaner period (a period of 39 days. In the first 6 d after weaning, pigs offered the HC diets gained weight faster and used feed more efficiently than those offered the LC diets (P = 0.031. Pigs fed a HC diet after weaning tended to be heavier at the sale live weight of 123 d of age compared with pigs fed the LC diet (P = 0.056. There were no other main effects of the feeding program on growth performance through to slaughter. Weaning weight had a profound influence on lifetime growth performance and weight at 123 d of age, with H pigs at weaning increasing their weight advantage over the M and L pigs (101.3, 97.1, 89.6 kg respectively, P < 0.001. Cost-benefit analyses suggested there was a minimal benefit in terms of cost per unit live weight gain over lifetime when pigs were offered a HC feeding program to L, with a lower feed cost/kg gain. The results from this investigation confirm the impact of weaning weight on lifetime growth performance, and suggest that a HC feeding program should be focused on L weaner pigs (i.e., weaning weight less than 6.5 kg at 27 d of age in order to maximise financial returns.

  2. A low cost, light weight cenosphere–aluminium composite for brake ...

    Indian Academy of Sciences (India)

    . Home; Journals; Bulletin of Materials Science; Volume 39; Issue 1. A low cost, light weight cenosphere–aluminium composite for brake disc application. V Saravanan P R Thyla S R Balakrishnan. Volume 39 Issue 1 February 2016 pp 299-305 ...

  3. Cost reduction in abdominal CT by weight-adjusted dose

    International Nuclear Information System (INIS)

    Arana, Estanislao; Marti-Bonmati, Luis; Tobarra, Eva; Sierra, Consuelo

    2009-01-01

    Aim: To analyze the influence of contrast dose adjusted by weight vs. fixed contrast dose in the attenuation and cost of abdominal computed tomography (CT). Materials and methods: A randomised, consecutive, parallel group study was conducted in 151 patients (74 men and 77 women, age range 22-67 years), studied with the same CT helical protocol. A dose at 1.75 ml/kg was administered in 101 patients while 50 patients had a fixed dose of 120 ml of same non-ionic contrast material (320 mg/ml). Mean enhancements were measured at right hepatic lobe, superior abdominal aorta and inferior cava vein. Statistical analysis was weight-stratified ( 81 kg). Results: Aortic attenuation was significantly superior (p 61 kg in dose-adjusted group, presented higher hepatic attenuation, being statistically significant in those >81 kg (p 80 kg, there was an over cost of Euro 10.7 per patient. Conclusions: An injection volume of 1.75 ml/kg offers an optimal diagnostic quality with a global savings of Euro 1.34 per patient.

  4. Influences of the Capital Structure and the Cost of Capital on Financial Performance. Case Study on ENGIE Group

    Directory of Open Access Journals (Sweden)

    Elena Valentina IVASCU

    2017-06-01

    Full Text Available The main objectives of the company's financial management are to ensure financial performances and to choose the capital structure that corresponds to the lowest total cost of capital. The purpose of this paper is to analyse the relationship between the capital structure and cost, and the financial performance of Engie Transnational Group, one of the most important global electricity producers. The data used were extracted from the Amadeus and Bloomberg databases for the period 2010-2015. Financial performance was analysed both by creating and proposing an aggregate index, as well as based on the Z Conan & Holder score. The company's financial structure was analysed on the basis of the total leverage ratio and for the total cost of capital, the weighted average capital cost formula was used. The results obtained at the Engie Group level show that the capital structure is predominantly indebted, and the maximum financial performance is obtained when the financial structure is minimal and the weighted average capital cost is maximum. The reversed relationship between the financial structure and the financial performance is in accordance with the financial structure theories of information asymmetry, pecking order and dynamic trade-off. The reversed relationship is confirmed in all Engie Group companies, except one company from United Kingdom.

  5. Configuration space analysis of common cost functions in radiotherapy beam-weight optimization algorithms

    Energy Technology Data Exchange (ETDEWEB)

    Rowbottom, Carl Graham [Joint Department of Physics, Institute of Cancer Research and the Royal Marsden NHS Trust, Sutton, Surrey (United Kingdom); Webb, Steve [Joint Department of Physics, Institute of Cancer Research and the Royal Marsden NHS Trust, Sutton, Surrey (United Kingdom)

    2002-01-07

    The successful implementation of downhill search engines in radiotherapy optimization algorithms depends on the absence of local minima in the search space. Such techniques are much faster than stochastic optimization methods but may become trapped in local minima if they exist. A technique known as 'configuration space analysis' was applied to examine the search space of cost functions used in radiotherapy beam-weight optimization algorithms. A downhill-simplex beam-weight optimization algorithm was run repeatedly to produce a frequency distribution of final cost values. By plotting the frequency distribution as a function of final cost, the existence of local minima can be determined. Common cost functions such as the quadratic deviation of dose to the planning target volume (PTV), integral dose to organs-at-risk (OARs), dose-threshold and dose-volume constraints for OARs were studied. Combinations of the cost functions were also considered. The simple cost function terms such as the quadratic PTV dose and integral dose to OAR cost function terms are not susceptible to local minima. In contrast, dose-threshold and dose-volume OAR constraint cost function terms are able to produce local minima in the example case studied. (author)

  6. Association of increased monetary cost of dietary intake, diet quality and weight management in Spanish adults.

    Science.gov (United States)

    Schröder, Helmut; Serra-Majem, Luis; Subirana, Isaac; Izquierdo-Pulido, Maria; Fitó, Montserrat; Elosua, Roberto

    2016-03-14

    Higher monetary diet cost is associated with healthier food choices and better weight management. How changes in diet cost affect changes in diet quality and weight remains unknown. The aim of this study was to assess the impact of changes in individual monetary diet cost on changes in diet quality, measured by the modified Mediterranean diet score recommendations (MDS-rec) and by energy density (ED), as well as changes in weight and BMI. We conducted a prospective, population-based study of 2181 male and female Spaniards aged between 25 and 74 years, who were followed up to the 2009-2010 academic year. We measured weight and height and recorded dietary data using a validated FFQ. Average food cost was calculated from official Spanish government data. We fitted multivariate linear and logistic regression models. The average daily diet cost increased from 3·68(SD0.0·89)€/8·36 MJ to 4·97(SD1·16)€/8·36 MJ during the study period. This increase was significantly associated with improvement in diet quality (Δ ED and Δ MDS-rec; Pcost per 8·36 MJ was associated with a decrease of 0·3 kg in body weight (P=0·02) and 0·1 kg/m(2) in BMI (P=0·04). These associations were attenuated after adjusting for changes in diet quality indicators. An improvement in diet quality and better weight management were both associated with an increase in diet cost; this could be considered in food policy decisions.

  7. The relationships between OHS prevention costs, safety performance, employee satisfaction and accident costs.

    Science.gov (United States)

    Bayram, Metin; Ünğan, Mustafa C; Ardıç, Kadir

    2017-06-01

    Little is known about the costs of safety. A literature review conducted for this study indicates there is a lack of survey-based research dealing with the effects of occupational health and safety (OHS) prevention costs. To close this gap in the literature, this study investigates the interwoven relationships between OHS prevention costs, employee satisfaction, OHS performance and accident costs. Data were collected from 159 OHS management system 18001-certified firms operating in Turkey and analyzed through structural equation modeling. The findings indicate that OHS prevention costs have a significant positive effect on safety performance, employee satisfaction and accident costs savings; employee satisfaction has a significant positive effect on accident costs savings; and occupational safety performance has a significant positive effect on employee satisfaction and accident costs savings. Also, the results indicate that safety performance and employee satisfaction leverage the relationship between prevention costs and accident costs.

  8. Accounting for future redesign to balance performance and development costs

    International Nuclear Information System (INIS)

    Villanueva, D.; Haftka, R.T.; Sankar, B.V.

    2014-01-01

    Most components undergo tests after they are designed and are redesigned if necessary. Tests help designers find unsafe and overly conservative designs, and redesign can restore safety or increase performance. In general, the expected changes to the performance and reliability of the design after the test and redesign are not considered. In this paper, we explore how modeling a future test and redesign provides a company an opportunity to balance development costs versus performance by simultaneously designing the design and the post-test redesign rules during the initial design stage. Due to regulations and tradition, safety margin and safety factor based design is a common practice in industry as opposed to probabilistic design. In this paper, we show that it is possible to continue to use safety margin based design, and employ probability solely to select safety margins and redesign criteria. In this study, we find the optimum safety margins and redesign criterion for an integrated thermal protection system. These are optimized in order to find a minimum mass design with minimal redesign costs. We observed that the optimum safety margin and redesign criterion call for an initially conservative design and use the redesign process to trim excess weight rather than restore safety. This would fit well with regulatory constraints, since regulations usually impose minimum safety margins. - Highlights: • Modeling future tests and redesign allows balancing performance and development cost. • We optimize safety margins and redesign criteria for desired balance. • We design with safety margins, with probabilistic optimization to decide the margins. • Redesign also allowed the trade-off of conservativeness and performance. • In our case it paid to be conservative initially but redesign for more

  9. Cost and performance analysis of physical security systems

    International Nuclear Information System (INIS)

    Hicks, M.J.; Yates, D.; Jago, W.H.; Phillips, A.W.

    1998-04-01

    Analysis of cost and performance of physical security systems can be a complex, multi-dimensional problem. There are a number of point tools that address various aspects of cost and performance analysis. Increased interest in cost tradeoffs of physical security alternatives has motivated development of an architecture called Cost and Performance Analysis (CPA), which takes a top-down approach to aligning cost and performance metrics. CPA incorporates results generated by existing physical security system performance analysis tools, and utilizes an existing cost analysis tool. The objective of this architecture is to offer comprehensive visualization of complex data to security analysts and decision-makers

  10. Cost-effectiveness of bone densitometry among Caucasian women and men without a prior fracture according to age and body weight.

    Science.gov (United States)

    Schousboe, J T; Gourlay, M; Fink, H A; Taylor, B C; Orwoll, E S; Barrett-Connor, E; Melton, L J; Cummings, S R; Ensrud, K E

    2013-01-01

    We used a microsimulation model to estimate the threshold body weights at which screening bone densitometry is cost-effective. Among women aged 55-65 years and men aged 55-75 years without a prior fracture, body weight can be used to identify those for whom bone densitometry is cost-effective. Bone densitometry may be more cost-effective for those with lower body weight since the prevalence of osteoporosis is higher for those with low body weight. Our purpose was to estimate weight thresholds below which bone densitometry is cost-effective for women and men without a prior clinical fracture at ages 55, 60, 65, 75, and 80 years. We used a microsimulation model to estimate the costs and health benefits of bone densitometry and 5 years of fracture prevention therapy for those without prior fracture but with femoral neck osteoporosis (T-score ≤ -2.5) and a 10-year hip fracture risk of ≥3%. Threshold pre-test probabilities of low BMD warranting drug therapy at which bone densitometry is cost-effective were calculated. Corresponding body weight thresholds were estimated using data from the Study of Osteoporotic Fractures (SOF), the Osteoporotic Fractures in Men (MrOS) study, and the National Health and Nutrition Examination Survey (NHANES) for 2005-2006. Assuming a willingness to pay of $75,000 per quality adjusted life year (QALY) and drug cost of $500/year, body weight thresholds below which bone densitometry is cost-effective for those without a prior fracture were 74, 90, and 100 kg, respectively, for women aged 55, 65, and 80 years; and were 67, 101, and 108 kg, respectively, for men aged 55, 75, and 80 years. For women aged 55-65 years and men aged 55-75 years without a prior fracture, body weight can be used to select those for whom bone densitometry is cost-effective.

  11. Cost analysis when open surgeons perform minimally invasive hysterectomy.

    Science.gov (United States)

    Shepherd, Jonathan P; Kantartzis, Kelly L; Ahn, Ki Hoon; Bonidie, Michael J; Lee, Ted

    2014-01-01

    The costs to perform a hysterectomy are widely variable. Our objective was to determine hysterectomy costs by route and whether traditionally open surgeons lower costs when performing laparoscopy versus robotics. Hysterectomy costs including subcategories were collected from 2011 to 2013. Costs were skewed, so 2 statistical transformations were performed. Costs were compared by surgeon classification (open, laparoscopic, or robotic) and surgery route. A total of 4,871 hysterectomies were performed: 34.2% open, 50.7% laparoscopic, and 15.1% robotic. Laparoscopic hysterectomy had the lowest total costs (P depreciation included (P < .001) but similar costs if these variables were excluded. Although laparoscopic hysterectomy had lowest costs overall, robotics may be no more costly than laparoscopic hysterectomy when performed by surgeons who predominantly perform open hysterectomy.

  12. Weighted Activity and Costing of Surveillance and Control in Animal Epidemiology

    Directory of Open Access Journals (Sweden)

    Duboz Raphaël

    2013-01-01

    Full Text Available Activity based modeling and simulation is a very promising field. It has recently demonstrated its potential from modeling software development methods [9] to the design of low energy sensors. In this position paper, I would like to initiate a reflexion on the use of the weighted activity in the context of financial costing using the formulation recently proposed by X. Hu and B.P. Zeigler [5]. I propose here to formalize a recent approach of costing, the Time-Driven Activity Based Costing [3], using the theoretical modeling framework initiated by B.P. Zeigler [6]. I argue that this specification can potentially improve the traditional model of Time-Driven Activity Based Costing. I illustrate the approach in the context of surveillance and control in animal epidemiology. The demonstration of its effectiveness is not done in this position paper. Nevertheless, as the existing costing systems are designed to support decision making in business management, the scenario based approach proposed in this paper should be very useful to support decisions in complex management situations.

  13. Practical session assessments in human anatomy: Weightings and performance.

    Science.gov (United States)

    McDonald, Aaron C; Chan, Siew-Pang; Schuijers, Johannes A

    2016-07-08

    Assessment weighting within a given module can be a motivating factor for students when deciding on their commitment level and time given to study a specific topic. In this study, an analysis of assessment performances of second year anatomy students was performed over four years to determine if (1) students performed better when a higher weighting was given to a set of practical session assessments and (2) whether an improved performance in the practical session assessments had a carry-over effect on other assessment tasks within that anatomy module and/or other anatomy modules that follow. Results showed that increasing the weighting of practical session assessments improved the average mark in that assessment and also improved the percentage of students passing that assessment. Further, it significantly improved performance in the written end-semester examination within the same module and had a carry-over effect on the anatomy module taught in the next teaching period, as students performed better in subsequent practical session assessments as well as subsequent end-semester examinations. It was concluded that the weighting of assessments had significant influences on a student's performance in that, and subsequent, assessments. It is postulated that practical session assessments, designed to develop deep learning skills in anatomy, improved efficacy in student performance in assessments undertaken in that and subsequent anatomy modules when the weighting of these assessments was greater. These deep learning skills were also transferable to other methods of assessing anatomy. Anat Sci Educ 9: 330-336. © 2015 American Association of Anatomists. © 2015 American Association of Anatomists.

  14. Cost and performance of innovative remediation technologies

    International Nuclear Information System (INIS)

    Cummings, J.B.; Kingscott, J.W.; Fiedler, L.D.

    1995-01-01

    The selection and use of more cost-effective remedies requires better access to data on the performance and cost of technologies used in the field. To make data more widely available, the US Environmental Protection Agency is working jointly with member agencies of the Federal Remediation Technologies Round table to publish case studies of full-scale remediation and demonstration projects. EPA, DoD, and DOE have published case studies of cleanup projects primarily consisting of bioremediation, soil vapor extraction, and thermal desorption. Within the limits of this initial data set, the paper evaluates technology performance and cost. In the analysis of cost factors, the paper shows the use of a standardized Work Breakdown Structure (WBS). Use of the WBS will be important in future reporting of completed projects to facilitate cost comparison. The paper notes the limits to normalization and thus cross-site comparison which can be achieved using the WBS. The paper identifies conclusions from initial efforts to compile cost and performance data, highlights the importance of such efforts to the overall remediation effort, and discusses future cost and performance documentation efforts

  15. Effects of independently altering body weight and body mass on the metabolic cost of running

    NARCIS (Netherlands)

    Teunissen, L.P.J.; Grabowski, A.; Kram, R.

    2011-01-01

    The metabolic cost of running is substantial, despite the savings from elastic energy storage and return. Previous studies suggest that generating vertical force to support body weight and horizontal forces to brake and propel body mass are the major determinants of the metabolic cost of running. In

  16. Development of lengths of stay and DRG cost weights in dermatology from 2003 to 2006.

    Science.gov (United States)

    Wenke, Andreas; Müller, Marcel L; Babapirali, Judith; Rompel, Rainer; Hensen, Peter

    2009-08-01

    The G-DRG per case payments are calculated annually on the basis of present output and cost data provided from German hospitals. The economic valuation of dermatology-related DRGs depends largely on inpatients' length of stay. At present, longitudinal analyses of dermatologic hospital data considering the development of length of stay under DRG conditions are not available. A multicenter, longitudinal study of clinical data from hospitals with different care levels was performed (n = 23). Frequent and relevant dermatologic diagnoses were grouped and analyzed over a time period of four years (2003-2006). The development of lengths of stay and of G-DRG cost weights were studied in detail. Descriptive statistical methods were applied. After introduction of DRG, the data reveal a) reduction of length of stay in inpatient dermatology and b) after an initial abrupt rise, DRG valuation of dermatologic groups moderately decreased over time. Both trends changed most rapidly in the early years but reached a stable niveau in 2006. The study furthermore points out that not only length of stay, but also other type of costs influence DRG calculations. German dermatology reflects the international trend showing reductions of length of stay after introduction of a DRG-based hospital funding system. The DRG calculation and valuation of inpatient services depend on the duration of hospital stay. However, increasing per diem costs resulting from higher performances of every inpatient bed day are also taken into account. Further reduction of length of stay must not threaten the quality of inpatient care in dermatology.

  17. Optimal dual-fuel propulsion for minimum inert weight or minimum fuel cost

    Science.gov (United States)

    Martin, J. A.

    1973-01-01

    An analytical investigation of single-stage vehicles with multiple propulsion phases has been conducted with the phasing optimized to minimize a general cost function. Some results are presented for linearized sizing relationships which indicate that single-stage-to-orbit, dual-fuel rocket vehicles can have lower inert weight than similar single-fuel rocket vehicles and that the advantage of dual-fuel vehicles can be increased if a dual-fuel engine is developed. The results also indicate that the optimum split can vary considerably with the choice of cost function to be minimized.

  18. Assessment of various failure theories for weight and cost optimized laminated composites using genetic algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Goyal, T. [Indian Institute of Technology Kanpur. Dept. of Aerospace Engineering, UP (India); Gupta, R. [Infotech Enterprises Ltd., Hyderabad (India)

    2012-07-01

    In this work, minimum weight-cost design for laminated composites is presented. A genetic algorithm has been developed for the optimization process. Maximum-Stress, Tsai-Wu and Tsai-Hill failure criteria have been used along with buckling analysis parameter for the margin of safety calculations. The design variables include three materials; namely Carbon-Epoxy, Glass-Epoxy, Kevlar-Epoxy; number of plies; ply orientation angles, varying from -75 deg. to 90 deg. in the intervals of 15 deg. and ply thicknesses which depend on the material in use. The total cost is a sum of material cost and layup cost. Layup cost is a function of the ply angle. Validation studies for solution convergence and weight-cost inverse proportionality are carried out. One set of results for shear loading are also validated from literature for a particular case. A Pareto-Optimal solution set is demonstrated for biaxial loading conditions. It is then extended to applied moments. It is found that global optimum for a given loading condition is a function of the failure criteria for shear loading, with Maximum Stress criteria giving the lightest-cheapest and Tsai-Wu criteria giving the heaviest-costliest optimized laminates. Optimized weight results are plotted from the three criteria to do a comparative study. This work gives a global optimized laminated composite and also a set of other local optimum laminates for a given set of loading conditions. The current algorithm also provides with adequate data to supplement the use of different failure criteria for varying loadings. This work can find use in the industry and/or academia considering the increased use of laminated composites in modern wind blades. (Author)

  19. On the performance of social network and likelihood-based expert weighting schemes

    International Nuclear Information System (INIS)

    Cooke, Roger M.; ElSaadany, Susie; Huang Xinzheng

    2008-01-01

    Using expert judgment data from the TU Delft's expert judgment database, we compare the performance of different weighting schemes, namely equal weighting, performance-based weighting from the classical model [Cooke RM. Experts in uncertainty. Oxford: Oxford University Press; 1991.], social network (SN) weighting and likelihood weighting. The picture that emerges with regard to SN weights is rather mixed. SN theory does not provide an alternative to performance-based combination of expert judgments, since the statistical accuracy of the SN decision maker is sometimes unacceptably low. On the other hand, it does outperform equal weighting in the majority of cases. The results here, though not overwhelmingly positive, do nonetheless motivate further research into social interaction methods for nominating and weighting experts. Indeed, a full expert judgment study with performance measurement requires an investment in time and effort, with a view to securing external validation. If high confidence in a comparable level of validation can be obtained by less intensive methods, this would be very welcome, and would facilitate the application of structured expert judgment in situations where the resources for a full study are not available. Likelihood weights are just as resource intensive as performance-based weights, and the evidence presented here suggests that they are inferior to performance-based weights with regard to those scoring variables which are optimized in performance weights (calibration and information). Perhaps surprisingly, they are also inferior with regard to likelihood. Their use is further discouraged by the fact that they constitute a strongly improper scoring rule

  20. Adolescent Anorexia Nervosa: cognitive performance after weight recovery.

    Science.gov (United States)

    Lozano-Serra, Estefanía; Andrés-Perpiña, Susana; Lázaro-García, Luisa; Castro-Fornieles, Josefina

    2014-01-01

    Although there is no definitive consensus on the impairment of neuropsychological functions, most studies of adults with Anorexia Nervosa (AN) find impaired functioning in cognitive domains such as visual-spatial abilities. The objective of this study is to assess the cognitive functions in adolescents with AN before and after weight recovery and to explore the relationship between cognitive performance and menstruation. Twenty-five female adolescents with AN were assessed by a neuropsychological battery while underweight and then following six months of treatment and weight recovery. Twenty-six healthy female subjects of a similar age were also evaluated at both time points. Underweight patients with AN showed worse cognitive performance than control subjects in immediate recall, organization and time taken to copy the Rey's Complex Figure Test (RCFT). After weight recovery, AN patients presented significant improvements in all tests, and differences between patients and controls disappeared. Patients with AN and persistence of amenorrhea at follow-up (n=8) performed worse on Block Design, delayed recall of Visual Reproduction and Stroop Test than patients with resumed menstruation (n=14) and the control group, though the two AN groups were similar in body mass index, age and psychopathological scale scores. Weight recovery improves cognitive functioning in adolescents with AN. The normalization of neuropsychological performance is better in patients who have recovered at least one menstrual cycle. The normalization of hormonal function seems to be essential for the normalization of cognitive performance, even in adolescents with a very short recovery time. © 2013.

  1. An integrated radar model solution for mission level performance and cost trades

    Science.gov (United States)

    Hodge, John; Duncan, Kerron; Zimmerman, Madeline; Drupp, Rob; Manno, Mike; Barrett, Donald; Smith, Amelia

    2017-05-01

    A fully integrated Mission-Level Radar model is in development as part of a multi-year effort under the Northrop Grumman Mission Systems (NGMS) sector's Model Based Engineering (MBE) initiative to digitally interconnect and unify previously separate performance and cost models. In 2016, an NGMS internal research and development (IR and D) funded multidisciplinary team integrated radio frequency (RF), power, control, size, weight, thermal, and cost models together using a commercial-off-the-shelf software, ModelCenter, for an Active Electronically Scanned Array (AESA) radar system. Each represented model was digitally connected with standard interfaces and unified to allow end-to-end mission system optimization and trade studies. The radar model was then linked to the Air Force's own mission modeling framework (AFSIM). The team first had to identify the necessary models, and with the aid of subject matter experts (SMEs) understand and document the inputs, outputs, and behaviors of the component models. This agile development process and collaboration enabled rapid integration of disparate models and the validation of their combined system performance. This MBE framework will allow NGMS to design systems more efficiently and affordably, optimize architectures, and provide increased value to the customer. The model integrates detailed component models that validate cost and performance at the physics level with high-level models that provide visualization of a platform mission. This connectivity of component to mission models allows hardware and software design solutions to be better optimized to meet mission needs, creating cost-optimal solutions for the customer, while reducing design cycle time through risk mitigation and early validation of design decisions.

  2. Cost-effectiveness of barium enemas performed by radiographers

    International Nuclear Information System (INIS)

    Brown, Lorraine; Desai, Sharad

    2002-01-01

    AIM: To assess the cost-effectiveness of barium enemas performed by radiographers compared to those performed by consultant radiologists. METHOD: Prospective study of 200 barium enemas carried out by a senior radiographer and a consultant radiologist. The sample was a consecutive sample of adult out-patients over a 3-month period, with no exclusion. The length of time of the enema and the numbers and grades of staff involved in the procedure were recorded. This was translated into staffing costs using the appropriate pay scales. RESULTS: The barium enemas performed by the superintendent radiographer were more cost-effective than those performed by the consultant radiologist (1406 pounds for 100 radiographer-performed barium enemas compared to 1787 pounds for 100 carried out by the consultant radiologist). CONCLUSION: In terms of staffing costs, radiographers performing barium enemas not only liberates radiologist time, it is also a cost-effective method of providing an out-patient barium enema service. Brown, L. and Desai, S. (2002)

  3. Cost Effectiveness of a Weight Management Program Implemented in the Worksite: Translation of Fuel Your Life.

    Science.gov (United States)

    Corso, Phaedra S; Ingels, Justin B; Padilla, Heather M; Zuercher, Heather; DeJoy, David M; Vandenberg, Robert J; Wilson, Mark G

    2018-04-18

    Conduct a cost-effectiveness analysis of the Fuel Your Life (FYL) program dissemination. Employees were recruited from three workplaces randomly assigned to one of the conditions: telephone coaching, small group coaching, and self-study. Costs were collected prospectively during the efficacy trial. The main outcome measures of interest were weight loss and quality-adjusted life years (QALYs). The phone condition was most costly ($601-$589/employee) and the self-study condition was least costly ($145-$143/employee). For weight loss, delivering FYL through the small group condition was no more effective, yet more expensive, than the self-study delivery. For QALYs, the group delivery of FYL was in an acceptable cost-effectiveness range ($22,400/QALY) relative to self-study (95% CI: $10,600/QALY - dominated). Prevention programs require adaptation at the local level and significantly affect the cost, effectiveness, and cost effectiveness of the program.This is an open access article distributed under the terms of the Creative Commons Attribution-Non Commercial-No Derivatives License 4.0 (CCBY-NC-ND), where it is permissible to download and share the work provided it is properly cited. The work cannot be changed in any way or used commercially without permission from the journal. http://creativecommons.org/licenses/by-nc-nd/4.0.

  4. Cost and performance analysis of physical security systems

    International Nuclear Information System (INIS)

    Hicks, M.J.; Yates, D.; Jago, W.H.

    1997-01-01

    CPA - Cost and Performance Analysis - is a prototype integration of existing PC-based cost and performance analysis tools: ACEIT (Automated Cost Estimating Integrated Tools) and ASSESS (Analytic System and Software for Evaluating Safeguards and Security). ACE is an existing DOD PC-based tool that supports cost analysis over the full life cycle of a system; that is, the cost to procure, operate, maintain and retire the system and all of its components. ASSESS is an existing DOE PC-based tool for analysis of performance of physical protection systems. Through CPA, the cost and performance data are collected into Excel workbooks, making the data readily available to analysts and decision makers in both tabular and graphical formats and at both the system and subsystem levels. The structure of the cost spreadsheets incorporates an activity-based approach to cost estimation. Activity-based costing (ABC) is an accounting philosophy used by industry to trace direct and indirect costs to the products or services of a business unit. By tracing costs through security sensors and procedures and then mapping the contributions of the various sensors and procedures to system effectiveness, the CPA architecture can provide security managers with information critical for both operational and strategic decisions. The architecture, features and applications of the CPA prototype are presented. 5 refs., 3 figs

  5. Economics of human performance and systems total ownership cost.

    Science.gov (United States)

    Onkham, Wilawan; Karwowski, Waldemar; Ahram, Tareq Z

    2012-01-01

    Financial costs of investing in people is associated with training, acquisition, recruiting, and resolving human errors have a significant impact on increased total ownership costs. These costs can also affect the exaggerate budgets and delayed schedules. The study of human performance economical assessment in the system acquisition process enhances the visibility of hidden cost drivers which support program management informed decisions. This paper presents the literature review of human total ownership cost (HTOC) and cost impacts on overall system performance. Economic value assessment models such as cost benefit analysis, risk-cost tradeoff analysis, expected value of utility function analysis (EV), growth readiness matrix, multi-attribute utility technique, and multi-regressions model were introduced to reflect the HTOC and human performance-technology tradeoffs in terms of the dollar value. The human total ownership regression model introduces to address the influencing human performance cost component measurement. Results from this study will increase understanding of relevant cost drivers in the system acquisition process over the long term.

  6. Cost and Performance Model for Photovoltaic Systems

    Science.gov (United States)

    Borden, C. S.; Smith, J. H.; Davisson, M. C.; Reiter, L. J.

    1986-01-01

    Lifetime cost and performance (LCP) model assists in assessment of design options for photovoltaic systems. LCP is simulation of performance, cost, and revenue streams associated with photovoltaic power systems connected to electric-utility grid. LCP provides user with substantial flexibility in specifying technical and economic environment of application.

  7. Cost analysis of biologic drugs in rheumatoid arthritis first line treatment after methotrexate failure according to patients' body weight.

    Science.gov (United States)

    Román Ivorra, José Andrés; Ivorra, José; Monte-Boquet, Emilio; Canal, Cristina; Oyagüez, Itziar; Gómez-Barrera, Manuel

    2016-01-01

    The objective was to assess the influence of patients' weight in the cost of rheumatoid arthritis treatment with biologic drugs used in first line after non-adequate response to methotrexate. Pharmaceutical and administration costs were calculated in two scenarios: non-optimization and optimization of intravenous (IV) vials. The retrospective analysis of 66 patients from a Spanish 1,000 beds-hospital Rheumatology Clinic Service was used to obtain posology and weight data. The study time horizon was two years. Costs were expressed in 2013 euros. For an average 69kg-weighted patient the lowest cost corresponded to abatacept subcutaneous (SC ABA) (€21,028.09) in the scenario without IV vials optimization and infliximab (IFX) (€20,779.29) with optimization. Considering patients' weight in the scenario without IV vials optimization infliximab (IFX) was the least expensive drug in patients ranged 45-49kg, IV ABA in 50-59kg and SC ABA in patients over 60kg. With IV vials optimization IFX was the least expensive drug in patients under 69kg and SC ABA over 70kg. Assuming comparable effectiveness of biological drugs, patient's weight is a variable to consider, potentials savings could reach €20,000 in two years. Copyright © 2015 Elsevier España, S.L.U. and Sociedad Española de Reumatología y Colegio Mexicano de Reumatología. All rights reserved.

  8. Classification of Company Performance using Weighted Probabilistic Neural Network

    Science.gov (United States)

    Yasin, Hasbi; Waridi Basyiruddin Arifin, Adi; Warsito, Budi

    2018-05-01

    Classification of company performance can be judged by looking at its financial status, whether good or bad state. Classification of company performance can be achieved by some approach, either parametric or non-parametric. Neural Network is one of non-parametric methods. One of Artificial Neural Network (ANN) models is Probabilistic Neural Network (PNN). PNN consists of four layers, i.e. input layer, pattern layer, addition layer, and output layer. The distance function used is the euclidean distance and each class share the same values as their weights. In this study used PNN that has been modified on the weighting process between the pattern layer and the addition layer by involving the calculation of the mahalanobis distance. This model is called the Weighted Probabilistic Neural Network (WPNN). The results show that the company's performance modeling with the WPNN model has a very high accuracy that reaches 100%.

  9. Cost of intervention delivery in a lifestyle weight loss trial in type 2 diabetes: results from the Look AHEAD clinical trial.

    Science.gov (United States)

    Rushing, J; Wing, R; Wadden, T A; Knowler, W C; Lawlor, M; Evans, M; Killean, T; Montez, M; Espeland, M A; Zhang, P

    2017-03-01

    The Action for Health in Diabetes (Look AHEAD) trial was a randomized controlled clinical trial to compare the effects of 10 years of intensive lifestyle intervention (ILI) with a control condition of diabetes support and education (DSE) on health outcomes in over 5,000 participants with type 2 diabetes. The ILI had significantly greater weight losses than DSE throughout the trial. The goal of this analysis is to describe the cost of delivering the intervention. The ILI was designed to promote weight loss and increase physical activity. It involved a combination of group plus individual intervention sessions, with decreasing frequency of contact over the 10 years. The intervention incorporated a variety of strategies, including meal replacement products, to improve weight loss outcomes. The costs of intervention delivery were derived from staff surveys of effort and from records of intervention materials from the 16 US academic clinical trial sites. Costs were calculated from the payer perspective and presented in 2012 dollars. During the first year, when intervention delivery was most intensive, the annual cost of intervention delivery, averaged (standard deviation) across clinical sites, was $2,864.6 ($513.3) per ILI participant compared with $202.4 ($76.6) per DSE participant. As intervention intensity declined, costs decreased, such that from years 5 to 9 of the trial, the annual cost of intervention was $1,119.8 ($227.7) per ILI participant and $102.9 ($33.0) per DSE participant. Staffing accounted for the majority of costs throughout the trial, with meal replacements and materials to promote adherence accounting for smaller shares. The sustained weight losses produced by the Look AHEAD intervention were supported by intervention costs that were within the range of other weight loss programmes. Future work will include an evaluation of the cost-effectiveness of the ILI and will contain additional follow-up data.

  10. Brain network analysis: separating cost from topology using cost-integration.

    Directory of Open Access Journals (Sweden)

    Cedric E Ginestet

    Full Text Available A statistically principled way of conducting brain network analysis is still lacking. Comparison of different populations of brain networks is hard because topology is inherently dependent on wiring cost, where cost is defined as the number of edges in an unweighted graph. In this paper, we evaluate the benefits and limitations associated with using cost-integrated topological metrics. Our focus is on comparing populations of weighted undirected graphs that differ in mean association weight, using global efficiency. Our key result shows that integrating over cost is equivalent to controlling for any monotonic transformation of the weight set of a weighted graph. That is, when integrating over cost, we eliminate the differences in topology that may be due to a monotonic transformation of the weight set. Our result holds for any unweighted topological measure, and for any choice of distribution over cost levels. Cost-integration is therefore helpful in disentangling differences in cost from differences in topology. By contrast, we show that the use of the weighted version of a topological metric is generally not a valid approach to this problem. Indeed, we prove that, under weak conditions, the use of the weighted version of global efficiency is equivalent to simply comparing weighted costs. Thus, we recommend the reporting of (i differences in weighted costs and (ii differences in cost-integrated topological measures with respect to different distributions over the cost domain. We demonstrate the application of these techniques in a re-analysis of an fMRI working memory task. We also provide a Monte Carlo method for approximating cost-integrated topological measures. Finally, we discuss the limitations of integrating topology over cost, which may pose problems when some weights are zero, when multiplicities exist in the ranks of the weights, and when one expects subtle cost-dependent topological differences, which could be masked by cost-integration.

  11. Brain Network Analysis: Separating Cost from Topology Using Cost-Integration

    Science.gov (United States)

    Ginestet, Cedric E.; Nichols, Thomas E.; Bullmore, Ed T.; Simmons, Andrew

    2011-01-01

    A statistically principled way of conducting brain network analysis is still lacking. Comparison of different populations of brain networks is hard because topology is inherently dependent on wiring cost, where cost is defined as the number of edges in an unweighted graph. In this paper, we evaluate the benefits and limitations associated with using cost-integrated topological metrics. Our focus is on comparing populations of weighted undirected graphs that differ in mean association weight, using global efficiency. Our key result shows that integrating over cost is equivalent to controlling for any monotonic transformation of the weight set of a weighted graph. That is, when integrating over cost, we eliminate the differences in topology that may be due to a monotonic transformation of the weight set. Our result holds for any unweighted topological measure, and for any choice of distribution over cost levels. Cost-integration is therefore helpful in disentangling differences in cost from differences in topology. By contrast, we show that the use of the weighted version of a topological metric is generally not a valid approach to this problem. Indeed, we prove that, under weak conditions, the use of the weighted version of global efficiency is equivalent to simply comparing weighted costs. Thus, we recommend the reporting of (i) differences in weighted costs and (ii) differences in cost-integrated topological measures with respect to different distributions over the cost domain. We demonstrate the application of these techniques in a re-analysis of an fMRI working memory task. We also provide a Monte Carlo method for approximating cost-integrated topological measures. Finally, we discuss the limitations of integrating topology over cost, which may pose problems when some weights are zero, when multiplicities exist in the ranks of the weights, and when one expects subtle cost-dependent topological differences, which could be masked by cost-integration. PMID:21829437

  12. The Effect of Birth Weight on Academic Performance: Instrumental Variable Analysis.

    Science.gov (United States)

    Lin, Shi Lin; Leung, Gabriel Matthew; Schooling, C Mary

    2017-05-01

    Observationally, lower birth weight is usually associated with poorer academic performance; whether this association is causal or the result of confounding is unknown. To investigate this question, we obtained an effect estimate, which can have a causal interpretation under specific assumptions, of birth weight on educational attainment using instrumental variable analysis based on single nucleotide polymorphisms determining birth weight combined with results from the Social Science Genetic Association Consortium study of 126,559 Caucasians. We similarly obtained an estimate of the effect of birth weight on academic performance in 4,067 adolescents from Hong Kong's (Chinese) Children of 1997 birth cohort (1997-2016), using twin status as an instrumental variable. Birth weight was not associated with years of schooling (per 100-g increase in birth weight, -0.006 years, 95% confidence interval (CI): -0.02, 0.01) or college completion (odds ratio = 1.00, 95% CI: 0.96, 1.03). Birth weight was also unrelated to academic performance in adolescents (per 100-g increase in birth weight, -0.004 grade, 95% CI: -0.04, 0.04) using instrumental variable analysis, although conventional regression gave a small positive association (0.02 higher grade, 95% CI: 0.01, 0.03). Observed associations of birth weight with academic performance may not be causal, suggesting that interventions should focus on the contextual factors generating this correlation. © The Author 2017. Published by Oxford University Press on behalf of the Johns Hopkins Bloomberg School of Public Health. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  13. Optimization Method of a Low Cost, High Performance Ceramic Proppant by Orthogonal Experimental Design

    Science.gov (United States)

    Zhou, Y.; Tian, Y. M.; Wang, K. Y.; Li, G.; Zou, X. W.; Chai, Y. S.

    2017-09-01

    This study focused on optimization method of a ceramic proppant material with both low cost and high performance that met the requirements of Chinese Petroleum and Gas Industry Standard (SY/T 5108-2006). The orthogonal experimental design of L9(34) was employed to study the significance sequence of three factors, including weight ratio of white clay to bauxite, dolomite content and sintering temperature. For the crush resistance, both the range analysis and variance analysis reflected the optimally experimental condition was weight ratio of white clay to bauxite=3/7, dolomite content=3 wt.%, temperature=1350°C. For the bulk density, the most important factor was the sintering temperature, followed by the dolomite content, and then the ratio of white clay to bauxite.

  14. Activity based costing the performance breakthrough

    CERN Document Server

    Turney, Peter B B

    1996-01-01

    Activity-based costing is a method of measuring the cost and performance of activities, products and customers. It is increasingly being seen as a more accurate method of costing than conventional costing systems, which are being superseded by the fact that automation means that direct material and labour consumption is now a far less accurate means of apportioning overheads. This practical book outlines why conventional cost systems fail, before going on to cover the advantages of activity-based costing, and describing how to put the system in place successfully, and how to apply the lessons learnt quickly. The book takes the reader step-by-step through the various processes involved, from setting up the system, through its operation, to evaluation of the results.

  15. Dutch elm disease control: performance and costs

    Science.gov (United States)

    William N., Jr. Cannon; David P. Worley

    1980-01-01

    Municipal programs to suppress Dutch elm disease have had highly variable results. Performance as measured by tree mortality was unrelated to control strategies. Costs for control programs were 37 to 76 percent less than costs without control programs in the 15-year time-span of the study. Only those municipalities that conducted a high-performance program could be...

  16. Retrofit Weight-Loss Outcomes at 6, 12, and 24 Months and Characteristics of 12-Month High Performers: A Retrospective Analysis.

    Science.gov (United States)

    Painter, Stefanie; Ditsch, Gary; Ahmed, Rezwan; Hanson, Nicholas Buck; Kachin, Kevin; Berger, Jan

    2016-08-22

    Obesity is the leading cause of preventable death costing the health care system billions of dollars. Combining self-monitoring technology with personalized behavior change strategies results in clinically significant weight loss. However, there is a lack of real-world outcomes in commercial weight-loss program research. Retrofit is a personalized weight management and disease-prevention solution. This study aimed to report Retrofit's weight-loss outcomes at 6, 12, and 24 months and characterize behaviors, age, and sex of high-performing participants who achieved weight loss of 10% or greater at 12 months. A retrospective analysis was performed from 2011 to 2014 using 2720 participants enrolled in a Retrofit weight-loss program. Participants had a starting body mass index (BMI) of >25 kg/m² and were at least 18 years of age. Weight measurements were assessed at 6, 12, and 24 months in the program to evaluate change in body weight, BMI, and percentage of participants who achieved 5% or greater weight loss. A secondary analysis characterized high-performing participants who lost ≥10% of their starting weight (n=238). Characterized behaviors were evaluated, including self-monitoring through weigh-ins, number of days wearing an activity tracker, daily step count average, and engagement through coaching conversations via Web-based messages, and number of coaching sessions attended. Average weight loss at 6 months was -5.55% for male and -4.86% for female participants. Male and female participants had an average weight loss of -6.28% and -5.37% at 12 months, respectively. Average weight loss at 24 months was -5.03% and -3.15% for males and females, respectively. Behaviors of high-performing participants were assessed at 12 months. Number of weigh-ins were greater in high-performing male (197.3 times vs 165.4 times, P=.001) and female participants (222 times vs 167 times, Pactivity tracker days and average steps per day were greater in high-performing females (304.7 vs

  17. The effect of dietary garlic supplementation on body weight gain, feed intake, feed conversion efficiency, faecal score, faecal coliform count and feeding cost in crossbred dairy calves.

    Science.gov (United States)

    Ghosh, Sudipta; Mehla, Ram K; Sirohi, S K; Roy, Biswajit

    2010-06-01

    Thirty-six crossbred calves (Holstein cross) of 5 days of age were used to study the effect of garlic extract feeding on their performance up to the age of 2 months (pre-ruminant stage). They were randomly allotted into treatment and control groups (18 numbers in each group). Performance was evaluated by measuring average body weight (BW) gain, feed intake (dry matter (DM), total digestible nutrient (TDN) and crude protein (CP)), feed conversion efficiency (FCE; DM, TDN and CP), faecal score, faecal coliform count and feeding cost. Diets were the same for the both groups. In addition, treatment group received garlic extract supplementation at 250 mg/kg BW per day per calf. Body weight measured weekly, feed intake measured twice daily, proximate analysis of feeds and fodders analysed weekly, faecal scores monitored daily and faecal coliform count done weekly. There was significant increase in average body weight gain, feed intake and FCE and significant decrease in severity of scours as measured by faecal score and faecal coliform count in the treatment group compared to the control group (P Feed cost per kilogramme BW gain was significantly lower in the treatment group compared to control group (P calves for better performance.

  18. Comprehensive Evaluation of Car-Body Light-Weighting Scheme Based on LCC Theory

    Directory of Open Access Journals (Sweden)

    Han Qing-lan

    2016-01-01

    Full Text Available In this paper, a comprehensive evaluation model of light-weighting scheme is established, which is based on three dimensions, including the life cycle costs of the resource consumed by the designed objects (LCC, willingness to pay for the environmental effect of resource consumption (WTP and performance (P. Firstly, cost of each stage is determined. Then, based on the resource classification, which is based on cost elements, determine the material list needed, and apply WTP weight coefficient to monetize life cycle environmental impact and obtain the life cycle comprehensive cost of designed scheme (TCC. In the next step Performance (P index is calculated to measure the value of the life cycle costs by applying AHP and SAW method, integrated (TCC and (P to achieve comprehensive evaluation of light-weighting scheme. Finally, the effectiveness of the evaluation model is verified by the example of car engine hood.

  19. Improving performance and reducing costs of cooling towers

    International Nuclear Information System (INIS)

    Bartz, J.A.

    1992-01-01

    Cooling towers represent a significant capital investment at a steam electric power station. In addition, deficiencies in thermal performance can result in major operating penalties of fuel cost, replacement energy, and capacity addition. This paper summarizes two recent EPRI research projects aimed at reducing thermal performance deficiencies and decreasing installed costs of evaporative cooling towers. First, EPRI Research Project 2113, Cooling Tower Performance Prediction and Improvement, is summarized. This project has resulted in published data sets on the measured thermal performance characteristics of a variety of cooling tower packings, computer codes to predict tower performance, and computer code validation through large-scale tower performance measurements. Principal results are contained in an EPRIGEMS software module, Cooling Tower Advisor. This PC- based software contains a tutorial plus codes to predict tower thermal performance, arranged in a user-friendly format. The second EPRI effort, Research Project 2819-10/11, Fabric Structures for Power Plant Applications, has resulted in designs and costs of large structures with shells constructed of recently-developed fabrics. Primary power plant applications for such structures are the shells of natural draft cooling towers and coal-pile covers. Fabric structures offer low initial cost, acceptable life, and seismic superiority, among other advantages. Detailed conceptual designs and installed cost data are reviewed. 8 refs., 9 figs., 3 tabs

  20. A cost analysis of implementing a behavioral weight loss intervention in community mental health settings: Results from the ACHIEVE trial.

    Science.gov (United States)

    Janssen, Ellen M; Jerome, Gerald J; Dalcin, Arlene T; Gennusa, Joseph V; Goldsholl, Stacy; Frick, Kevin D; Wang, Nae-Yuh; Appel, Lawrence J; Daumit, Gail L

    2017-06-01

    In the ACHIEVE randomized controlled trial, an 18-month behavioral intervention accomplished weight loss in persons with serious mental illness who attended community psychiatric rehabilitation programs. This analysis estimates costs for delivering the intervention during the study. It also estimates expected costs to implement the intervention more widely in a range of community mental health programs. Using empirical data, costs were calculated from the perspective of a community psychiatric rehabilitation program delivering the intervention. Personnel and travel costs were calculated using time sheet data. Rent and supply costs were calculated using rent per square foot and intervention records. A univariate sensitivity analysis and an expert-informed sensitivity analysis were conducted. With 144 participants receiving the intervention and a mean weight loss of 3.4 kg, costs of $95 per participant per month and $501 per kilogram lost in the trial were calculated. In univariate sensitivity analysis, costs ranged from $402 to $725 per kilogram lost. Through expert-informed sensitivity analysis, it was estimated that rehabilitation programs could implement the intervention for $68 to $85 per client per month. Costs of implementing the ACHIEVE intervention were in the range of other intensive behavioral weight loss interventions. Wider implementation of efficacious lifestyle interventions in community mental health settings will require adequate funding mechanisms. © 2017 The Obesity Society.

  1. Thermal performance of heavy-weight and light-weight steel frame construction approaches in the central Pretoria climate

    CSIR Research Space (South Africa)

    Kumirai, T

    2013-01-01

    Full Text Available -1 Journal for New Generation Sciences Thermal performance of heavy-weight and light-weight steel frame construction approaches in the central Pretoria climate T Kumirai and DCU Conradie Built Environment, Council for Scientific and Industrial...

  2. Trojan Decommissioning Project Cost Performance

    International Nuclear Information System (INIS)

    Michael B. Lackey

    2000-01-01

    The Trojan nuclear plant (Trojan) was an 1160-MW(electric) four-loop pressurized water reactor located in Rainier, Oregon. The plant was permanently shut down in 1993 after ∼17 yr of commercial operation. The early plant closure was an economic decision. The key factors in the closure analysis were escalation of inspection and repair costs associated with steam generator tube cracking and the projected availability of inexpensive replacement power in the Pacific Northwest region of the United States. Since the plant closure, Portland General Electric (PGE) has been actively engaged in decommissioning. The Trojan Decommissioning Project currently has a forecast at completion of $429.7 million (all costs are in millions of 1997 dollars, unless otherwise noted). The cost performance of the Trojan Decommissioning Project to date is addressed, as well as the tools that are in place to provide cost control through completion of decommissioning

  3. Political versus managerial use of cost and performance accounting

    OpenAIRE

    Flury, Reto; Schedler, Kuno

    2006-01-01

    This article explains why it is impossible to use cost and performance accounting in public administration purely as an instrument for internal management. The authors report on a survey in Switzerland which highlighted the different expectations that politicians and managers have for cost and performance accounting. The authors warn that politicians and managers need to be aware of the conflicts arising from their different information needs. New cost and performance accounting systems need ...

  4. Cost performance assessment of in situ vitrification

    International Nuclear Information System (INIS)

    Showalter, W.E.; Letellier, B.C.; Booth, S.R.; Barnes-Smith, P.

    1992-01-01

    In situ vitrification (ISV) is a thermal treatment technology with promise for the destruction or immobilization of hazardous materials in contaminated soils. It has developed over the past decade to a level of maturity where meaningful cost effectiveness studies may be performed. The ISV process melts 4 to 25 m 2 of undisturbed soil to a maximum depth of 6 m into an obsidian-like glass waste form by applying electric current (3750 kill) between symmetrically spaced electrodes. Temperatures of approximately 2000 degree C drive off and destroy complex organics which are captured in an off-gas treatment system, while radio-nuclides are incorporated into the homogeneous glass monolith. A comparative life-cycle cost evaluation between mobile rotary kiln incineration and ISV was performed to quantitatively identify appropriate performance regimes and components of cost which are sensitive to the implementation of each technology. Predictions of melt times and power consumption were obtained from an ISV performance model over ranges of several parameters including electrode spacing, soil moisture, melt depth, electrical resistivity, and soil density. These data were coupled with manpower requirements, capitalization costs, and a melt placement optimization routine to allow interpolation over a wide variety of site characteristics. For the purpose of this study, a single site scenario representative of a mixed waste evaporation pond was constructed. Preliminary comparisons between ISV and incineration show that while operating costs are comparable, ISV avoids secondary treatment and monitored storage of radioactive waste that would be required following conventional incineration. It is the long term storage of incinerated material that is the most expensive component

  5. Photovoltaic technology, performance, manufacturing cost and markets

    International Nuclear Information System (INIS)

    Maycock, P.D.

    1999-01-01

    A comprehensive discussion of key aspects of photovoltaic energy conversion systems will provide the basis for forecasting PV module shipments from 1999 to 2010. Principal areas covered include: (1) Technology and Performance Status: The module efficiency and performance are described for commercial cell technologies including single crystal silicon, polycrystal silicon, ribbon silicon, film silicon on low cost substrate, amorphous silicon, copper indium diselenide, and cadmium telluride; (2) Manufacturing cost: 1999 costs for PV technologies in production (single crystal silicon, polycrystal silicon, and amorphous silicon) are developed. Manufacturing costs for 10--25 MW plants and 100 MW plants will be estimated; (3) The world PV market is summarized by region, top ten companies, and technology; and (4) Forecast of the World Market (seven market sectors) to 2010 will be presented. Key assumptions, price of modules, incentive programs, price of competing electricity generation will be detailed

  6. Energetic costs of performance in trained and untrained Anolis carolinensis lizards.

    Science.gov (United States)

    Lailvaux, Simon P; Wang, Andrew Z; Husak, Jerry F

    2018-03-12

    The energetic costs of performance constitute a non-trivial component of animals' daily energetic budgets. However, we currently lack an understanding of how those costs are partitioned among the various stages of performance development, maintenance, and production. We manipulated individual investment in performance by training Anolis carolinensis lizards for endurance or sprinting ability. We then measured energetic expenditure both at rest and immediately following exercise to test whether such training alters the maintenance and production costs of performance. Trained lizards had lower resting metabolic rates than controls, suggestive of a maintenance saving associated with enhanced performance as opposed to a cost. Production costs also differed, with sprint-trained lizards incurring the largest energetic performance cost and experiencing the longest recovery times compared to endurance trained and control animals. Although performance training modifies metabolism, production costs are probably the key drivers of trade-offs between performance and other life-history traits in this species. © 2018. Published by The Company of Biologists Ltd.

  7. Plastic packaged microcircuits: Quality, reliability, and cost issues

    Science.gov (United States)

    Pecht, Michael G.; Agarwal, Rakesh; Quearry, Dan

    1993-12-01

    Plastic encapsulated microcircuits (PEMs) find their main application in commercial and telecommunication electronics. The advantages of PEMs in cost, size, weight, performance, and market lead-time, have attracted 97% of the market share of worldwide microcircuit sales. However, PEMs have always been resisted in US Government and military applications due to the perception that PEM reliability is low. This paper surveys plastic packaging with respect to the issues of reliability, market lead-time, performance, cost, and weight as a means to guide part-selection and system-design.

  8. Financial indicators to evaluate the economic performance of feedlot steers with different slaughter weights

    Directory of Open Access Journals (Sweden)

    Edom de Avila Fabricio

    Full Text Available ABSTRACT: The objective of this study was to evaluate various financial indicators, estimated deterministically (considering historical quotes twelve consecutive years - 2003 to 2014, on the economic feasibility of finishing steers commercialized with different weights, using the simulation technique. Performance data steers were simulated with average initial weight of 350kg, fed in feedlot and slaughtered with 410, 440, 470, 500, 530, 560 and 590kg. The feeding period varies from 46 to 185 days, respectively. Based in various economic indicators, the viability of the investment decreased linearly according to the increase in slaughter weight. The coefficient of simple linear regression and means from lowest to highest slaughter weight were, respectively: net present value (-0.538 and R$ 67.37, R$ 65.28, R$ 32.14, R$ -7.34, R$ 8.01, R$ -12.38, R$ -23.41; index benefit: cost (-0.0003 and R$ 1.042, R$ 1.039, R$ 1.014, R$ 1.006, R$ 1.003, R$ 0.995, R$ 0.991; additional return on investment (-0.009 and 1.38, 1.29, 0.35, 0.11, 0.05, -0.08, -0.13% per month; internal rate of return (-0.009 and 2.21, 2.10, 1.28, 0.80, 0.93, 0.78, 0.73% per month. Feedlot use as termination option to obtain the direct benefits of this technology is an alternative investment with low economic return.

  9. Integrated cost estimation methodology to support high-performance building design

    Energy Technology Data Exchange (ETDEWEB)

    Vaidya, Prasad; Greden, Lara; Eijadi, David; McDougall, Tom [The Weidt Group, Minnetonka (United States); Cole, Ray [Axiom Engineers, Monterey (United States)

    2007-07-01

    Design teams evaluating the performance of energy conservation measures (ECMs) calculate energy savings rigorously with established modelling protocols, accounting for the interaction between various measures. However, incremental cost calculations do not have a similar rigor. Often there is no recognition of cost reductions with integrated design, nor is there assessment of cost interactions amongst measures. This lack of rigor feeds the notion that high-performance buildings cost more, creating a barrier for design teams pursuing aggressive high-performance outcomes. This study proposes an alternative integrated methodology to arrive at a lower perceived incremental cost for improved energy performance. The methodology is based on the use of energy simulations as means towards integrated design and cost estimation. Various points along the spectrum of integration are identified and characterized by the amount of design effort invested, the scheduling of effort, and relative energy performance of the resultant design. It includes a study of the interactions between building system parameters as they relate to capital costs. Several cost interactions amongst energy measures are found to be significant.The value of this approach is demonstrated with alternatives in a case study that shows the differences between perceived costs for energy measures along various points on the integration spectrum. These alternatives show design tradeoffs and identify how decisions would have been different with a standard costing approach. Areas of further research to make the methodology more robust are identified. Policy measures to encourage the integrated approach and reduce the barriers towards improved energy performance are discussed.

  10. PERFORMANCE ASSESSMENT OF INTEGRATED SENSOR ORIENTATION WITH A LOW-COST GNSS RECEIVER

    Directory of Open Access Journals (Sweden)

    M. Rehak

    2017-08-01

    Full Text Available Mapping with Micro Aerial Vehicles (MAVs whose weight does not exceed 5 kg is gaining importance in applications such as corridor mapping, road and pipeline inspections, or mapping of large areas with homogeneous surface structure, e.g. forest or agricultural fields. In these challenging scenarios, integrated sensor orientation (ISO improves effectiveness and accuracy. Furthermore, in block geometry configurations, this mode of operation allows mapping without ground control points (GCPs. Accurate camera positions are traditionally determined by carrier-phase GNSS (Global Navigation Satellite System positioning. However, such mode of positioning has strong requirements on receiver’s and antenna’s performance. In this article, we present a mapping project in which we employ a single-frequency, low-cost (< $100 GNSS receiver on a MAV. The performance of the low-cost receiver is assessed by comparing its trajectory with a reference trajectory obtained by a survey-grade, multi-frequency GNSS receiver. In addition, the camera positions derived from these two trajectories are used as observations in bundle adjustment (BA projects and mapping accuracy is evaluated at check points (ChP. Several BA scenarios are considered with absolute and relative aerial position control. Additionally, the presented experiments show the possibility of BA to determine a camera-antenna spatial offset, so-called lever-arm.

  11. Effect of Parental Live Weight on the Reproductive Performance of ...

    African Journals Online (AJOL)

    High mortality was obtained from HM x HF and HM x LF crosses. This study concluded that light male and light female crosses gave chicks with better post hatching performance and lowest mortality rate than all other crosses. Keywords: Parental live weight, Egg weight, Hatchability, Fertility, Crosses, Japanese quail ...

  12. Cost-optimal levels for energy performance requirements

    DEFF Research Database (Denmark)

    Thomsen, Kirsten Engelund; Aggerholm, Søren; Kluttig-Erhorn, Heike

    2011-01-01

    The CA conducted a study on experiences and challenges for setting cost optimal levels for energy performance requirements. The results were used as input by the EU Commission in their work of establishing the Regulation on a comparative methodology framework for calculating cost optimal levels...... of minimum energy performance requirements. In addition to the summary report released in August 2011, the full detailed report on this study is now also made available, just as the EC is about to publish its proposed Regulation for MS to apply in their process to update national building requirements....

  13. Green analytical chemistry introduction to chloropropanols determination at no economic and analytical performance costs?

    Science.gov (United States)

    Jędrkiewicz, Renata; Orłowski, Aleksander; Namieśnik, Jacek; Tobiszewski, Marek

    2016-01-15

    In this study we perform ranking of analytical procedures for 3-monochloropropane-1,2-diol determination in soy sauces by PROMETHEE method. Multicriteria decision analysis was performed for three different scenarios - metrological, economic and environmental, by application of different weights to decision making criteria. All three scenarios indicate capillary electrophoresis-based procedure as the most preferable. Apart from that the details of ranking results differ for these three scenarios. The second run of rankings was done for scenarios that include metrological, economic and environmental criteria only, neglecting others. These results show that green analytical chemistry-based selection correlates with economic, while there is no correlation with metrological ones. This is an implication that green analytical chemistry can be brought into laboratories without analytical performance costs and it is even supported by economic reasons. Copyright © 2015 Elsevier B.V. All rights reserved.

  14. Cost savings from performance-based maintenance contracting

    NARCIS (Netherlands)

    Straub, A.

    2009-01-01

    New procurement approaches combined with performance-based building approaches should reduce costs, but empirical qualitative and quantitative studies are lacking. Performance-based maintenance contracts give maintenance suppliers incentives to improve their way of working. Innovative,

  15. Implications of fin profiles on overall performance and weight reduction of a fin and tube heat exchanger

    DEFF Research Database (Denmark)

    Singh, Shobhana; Sørensen, Kim; Simonsen, Anders Schou

    2017-01-01

    Fin and tube heat exchangers are being used in several industrial applications by means of novel design and optimized performance. Improvements in geometric design may deliver energy efficient and cost-effective heat exchanger performance with reduced weight. In this paper, a systematic study...... on a cross-flow type fin and tube heat exchanger design for a waste heat recovery application is conducted. The geometric profile of the fin is characterized by a dimensionless design variable named aspect ratio which is parametrically varied to obtain different profiles. Two cases, case-I, and case......,000 using computational fluid dynamics. The numerical results obtained for the reference fin profile are verified with the experimental correlations. Dimensionless parameters such as Nusselt number, Euler number, and efficiency index are calculated to predict the overall performance of the heat exchanger...

  16. Centrality measures for immunization of weighted networks

    Directory of Open Access Journals (Sweden)

    Mohammad Khansari

    2016-03-01

    Full Text Available Effective immunization of individual communities with minimal cost in vaccination has made great discussion surrounding the realm of complex networks. Meanwhile, proper realization of relationship among people in society and applying it to social networks brings about substantial improvements in immunization. Accordingly, weighted graph in which link weights represent the intensity and intimacy of relationships is an acceptable approach. In this work we employ weighted graphs and a wide variety of weighted centrality measures to distinguish important individuals in contagion of diseases. Furthermore, we propose new centrality measures for weighted networks. Our experimental results show that Radiality-Degree centrality is satisfying for weighted BA networks. Additionally, PageRank-Degree and Radiality-Degree centralities showmoreacceptable performance in targeted immunization of weighted networks.

  17. Model reduction by weighted Component Cost Analysis

    Science.gov (United States)

    Kim, Jae H.; Skelton, Robert E.

    1990-01-01

    Component Cost Analysis considers any given system driven by a white noise process as an interconnection of different components, and assigns a metric called 'component cost' to each component. These component costs measure the contribution of each component to a predefined quadratic cost function. A reduced-order model of the given system may be obtained by deleting those components that have the smallest component costs. The theory of Component Cost Analysis is extended to include finite-bandwidth colored noises. The results also apply when actuators have dynamics of their own. Closed-form analytical expressions of component costs are also derived for a mechanical system described by its modal data. This is very useful to compute the modal costs of very high order systems. A numerical example for MINIMAST system is presented.

  18. Equivalent weight loss for weight management programs delivered by phone and clinic

    Science.gov (United States)

    Donnelly, Joseph E.; Goetz, Jeannine; Gibson, Cheryl; Sullivan, Debra K.; Lee, Robert; Smith, Bryan K.; Lambourne, Kate; Mayo, Matthew S.; Hunt, Suzanne; Lee, Jae Hoon; Honas, Jeffrey J.; Washburn, Richard A.

    2013-01-01

    Objective Face-to-face weight management is costly and presents barriers for individuals seeking treatment; thus, alternate delivery systems are needed. The objective of this study was to compare weight management delivered by face-to-face (FTF) clinic or group conference calls (phone). Design and Methods Randomized equivalency trial in 295 overweight/obese men/women (BMI = 35.1±4.9, Age = 43.8±10.2, Minority = 39.8%). Weight loss (0–6 months) was achieved by reducing energy intake between 1,200– 1,500 kcal/day and progressing physical activity to 300 minutes/week. Weight maintenance (7–18 months) provided adequate energy to maintain weight and continued 300 minutes/week of physical activity. Behavioral weight management strategies were delivered weekly for 6 months and gradually reduced during months 7–18. A cost analysis provided a comparison of expenses between groups. Results Weight change from baseline to 6 months was −13.4 ± 6.7% and −12.3 ± 7.0% for FTF clinic and phone, respectively. Weight change from 6 months to 18 months was 6.4 ± 7.0% and 6.4 ± 5.2%, for FTF clinic and phone, respectively. The cost to FTF participants was $789.58 more person. Conclusions Phone delivery provided equivalent weight loss and maintenance and reduced program cost. Ubiquitous access to phones provides a vast reach for this approach. PMID:23408579

  19. GASIFICATION PLANT COST AND PERFORMANCE OPTIMIZATION

    Energy Technology Data Exchange (ETDEWEB)

    Samuel S. Tam

    2002-05-01

    The goal of this series of design and estimating efforts was to start from the as-built design and actual operating data from the DOE sponsored Wabash River Coal Gasification Repowering Project and to develop optimized designs for several coal and petroleum coke IGCC power and coproduction projects. First, the team developed a design for a grass-roots plant equivalent to the Wabash River Coal Gasification Repowering Project to provide a starting point and a detailed mid-year 2000 cost estimate based on the actual as-built plant design and subsequent modifications (Subtask 1.1). This unoptimized plant has a thermal efficiency of 38.3% (HHV) and a mid-year 2000 EPC cost of 1,681 $/kW. This design was enlarged and modified to become a Petroleum Coke IGCC Coproduction Plant (Subtask 1.2) that produces hydrogen, industrial grade steam, and fuel gas for an adjacent Gulf Coast petroleum refinery in addition to export power. A structured Value Improving Practices (VIP) approach was applied to reduce costs and improve performance. The base case (Subtask 1.3) Optimized Petroleum Coke IGCC Coproduction Plant increased the power output by 16% and reduced the plant cost by 23%. The study looked at several options for gasifier sparing to enhance availability. Subtask 1.9 produced a detailed report on this availability analyses study. The Subtask 1.3 Next Plant, which retains the preferred spare gasification train approach, only reduced the cost by about 21%, but it has the highest availability (94.6%) and produces power at 30 $/MW-hr (at a 12% ROI). Thus, such a coke-fueled IGCC coproduction plant could fill a near term niche market. In all cases, the emissions performance of these plants is superior to the Wabash River project. Subtasks 1.5A and B developed designs for single-train coal and coke-fueled power plants. This side-by-side comparison of these plants, which contain the Subtask 1.3 VIP enhancements, showed their similarity both in design and cost (1,318 $/kW for the

  20. The Effect of Cost Sharing on an Employee Weight Loss Program: A Randomized Trial.

    Science.gov (United States)

    John, Leslie K; Troxel, Andrea B; Yancy, William S; Friedman, Joelle; Zhu, Jingsan; Yang, Lin; Galvin, Robert; Miller-Kovach, Karen; Halpern, Scott D; Loewenstein, George; Volpp, Kevin

    2018-01-01

    To test the effects of employer subsidies on employee enrollment, attendance, and weight loss in a nationally available weight management program. A randomized trial tested the impact of employer subsidy: 100%; 80%, 50%, and a hybrid 50% subsidy that could become a 100% subsidy by attaining attendance targets. NCT01756066. Twenty three thousand twenty-three employees of 2 US companies. The primary outcome was the percentage of employees who enrolled in the weight management program. We also tested whether the subsidies were associated with differential attendance and weight loss over 12 months, as might be predicted by the expectation that they attract employees with differing degrees of motivation. Analysis and Results: Enrollment differed significantly by subsidy level ( P < .0001). The 100% subsidy produced the highest enrollment (7.7%), significantly higher than each of the lower subsidies (vs 80% subsidy: 6.2%, P = .002; vs 50% subsidy: 3.9%, P < .0001; vs hybrid: 3.7%, P < .0001). Enrollment in the 80% subsidy group was significantly higher than both lower subsidy groups (vs 50% subsidy: 3.9%, P < .0001; vs hybrid: 3.7%, P < .0001). Among enrollees, there were no differences among the 4 groups in attendance or weight loss. This pragmatic trial, conducted in a real-world workplace setting, suggests that higher rates of employer subsidization help individuals to enroll in weight loss programs, without a decrement in program effectiveness. Future research could explore the cost-effectiveness of such subsidies or alternative designs.

  1. Cost sharing and HEDIS performance.

    Science.gov (United States)

    Chernew, Michael; Gibson, Teresa B

    2008-12-01

    Physicians, health plans, and health systems are increasingly evaluated and rewarded based on Health Plan Effectiveness Data and Information Set (HEDIS) and HEDIS-like performance measures. Concurrently, employers and health plans continue to try to control expenditures by increasing out-of-pocket costs for patients. The authors use fixed-effect logit models to assess how rising copayment rates for physician office visits and prescription drugs affect performance on HEDIS measures. Findings suggest that the increase in copayment rates lowers performance scores, demonstrating the connection between financial aspects of plan design and quality performance, and highlighting the potential weakness of holding plans and providers responsible for performance when payers and benefit plan managers also influence performance. Yet the effects are not consistent across all domains and, in many cases, are relatively modest in magnitude. This may reflect the HEDIS definitions and suggests that more sensitive measures may capture the impact of benefit design changes on performance.

  2. [Development of key indicators for nurses performance evaluation and estimation of their weights for management by objectives].

    Science.gov (United States)

    Lee, Eun Hwa; Ahn, Sung Hee

    2010-02-01

    This methodological research was designed to develop performance evaluation key indicators (PEKIs) for management by objectives (MBO) and to estimate their weights for hospital nurses. The PEKIs were developed by selecting preliminary indicators from a literature review, examining content validity and identifying their level of importance. Data were collected from November 14, 2007 to February 18, 2008. Data set for importance of indicators was obtained from 464 nurses and weights of PEKIs domain was from 453 nurses, who worked for at least 2 yr in one of three hospitals. Data were analyzed using X(2)-test, factor analysis, and the Analytical Hierarchy Process. Based upon Content Validity Index of .8 or above, 61 indicators were selected from the 100 preliminary indicators. Finally, 40 PEKIs were developed from the 61 indicators, and categorized into 10 domains. The highest weight of the 10 domains was customer satisfaction, which was followed by patient education, direct nursing care, profit increase, safety management, improvement of nursing quality, completeness of nursing records, enhancing competence of nurses, indirect nursing care, and cost reduction, in that order. PEKIs and their weights can be utilized for impartial evaluation and MBO for hospital nurses. Further research to verify PEKIs would lead to successful implementation of MBO.

  3. Effects of alternative promoters of growth on the performance and cost of production of broilers

    Directory of Open Access Journals (Sweden)

    Patrícia Tomazini Medeiros

    2009-09-01

    Full Text Available Probiotics and prebiotics were compared to antimicrobials as alternative growth promoters in male broilers grown from 1 to 42 days of age. Eight treatments were evaluated: a control feed without antimicrobials or alternative growth promoters, a control feed with antimicrobials, a control feed with the antimicrobials colistine and avilamicine, three rations with probiotic Bacillus subtilis in different concentrations and/or under recommended usage, one ration with probiotic Saccharomyces cerevisiae in addition to a mixture of probiotic Bacillus subtilis, Saccharomyces cerevisiae and Aspergillus oryzae, and one ration with mananoligossacarids (MOS plus betaglutanes. Antimicrobials and alternative growth promoters were added to an initial feed and to a growth feed common to all birds. Thirteen to 17 replicates of 50 birds of a Cobb line were utilized per treatment in a completely randomized design. Feed consumption, feed conversion and production costs did not significantly differ among treatments. The weights of 42-day-old birds fed on Bacillus subtilis (1,6 x 109CFU/g or the mixture of probiotics were higher or similar to the weights of birds fed on ration with antimicrobials. It was concluded that probiotics can replace antimicrobials as growth promoters for broilers up to 42 days of age without negative effects on growth performance and production cost.

  4. A Performance Weighted Collaborative Filtering algorithm for personalized radiology education.

    Science.gov (United States)

    Lin, Hongli; Yang, Xuedong; Wang, Weisheng; Luo, Jiawei

    2014-10-01

    Devising an accurate prediction algorithm that can predict the difficulty level of cases for individuals and then selects suitable cases for them is essential to the development of a personalized training system. In this paper, we propose a novel approach, called Performance Weighted Collaborative Filtering (PWCF), to predict the difficulty level of each case for individuals. The main idea of PWCF is to assign an optimal weight to each rating used for predicting the difficulty level of a target case for a trainee, rather than using an equal weight for all ratings as in traditional collaborative filtering methods. The assigned weight is a function of the performance level of the trainee at which the rating was made. The PWCF method and the traditional method are compared using two datasets. The experimental data are then evaluated by means of the MAE metric. Our experimental results show that PWCF outperforms the traditional methods by 8.12% and 17.05%, respectively, over the two datasets, in terms of prediction precision. This suggests that PWCF is a viable method for the development of personalized training systems in radiology education. Copyright © 2014. Published by Elsevier Inc.

  5. Performance of AC/graphite capacitors at high weight ratios of AC/graphite

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Hongyu [IM and T Ltd., Advanced Research Center, Saga University, 1341 Yoga-machi, Saga 840-0047 (Japan); Yoshio, Masaki [Advanced Research Center, Department of Applied Chemistry, Saga University, 1341 Yoga-machi, Saga 840-0047 (Japan)

    2008-03-01

    The effect of negative to positive electrode materials' weight ratio on the electrochemical performance of both activated carbon (AC)/AC and AC/graphite capacitors has been investigated, especially in the terms of capacity and cycle-ability. The limited capacity charge mode has been proposed to improve the cycle performance of AC/graphite capacitors at high weight ratios of AC/graphite. (author)

  6. Performance Errors in Weight Training and Their Correction.

    Science.gov (United States)

    Downing, John H.; Lander, Jeffrey E.

    2002-01-01

    Addresses general performance errors in weight training, also discussing each category of error separately. The paper focuses on frequency and intensity, incorrect training velocities, full range of motion, and symmetrical training. It also examines specific errors related to the bench press, squat, military press, and bent- over and seated row…

  7. A cost-performance model for ground-based optical communications receiving telescopes

    Science.gov (United States)

    Lesh, J. R.; Robinson, D. L.

    1986-01-01

    An analytical cost-performance model for a ground-based optical communications receiving telescope is presented. The model considers costs of existing telescopes as a function of diameter and field of view. This, coupled with communication performance as a function of receiver diameter and field of view, yields the appropriate telescope cost versus communication performance curve.

  8. Costs of examinations performed in a hospital laboratory in Chile.

    Science.gov (United States)

    Andrade, Germán Lobos; Palma, Carolina Salas

    2018-01-01

    To determine the total average costs related to laboratory examinations performed in a hospital laboratory in Chile. Retrospective study with data from July 2014 to June 2015. 92 examinations classified in ten groups were selected according to the analysis methodology. The costs were estimated as the sum of direct and indirect laboratory costs and indirect institutional factors. The average values obtained for the costs according to examination group (in USD) were: 1.79 (clinical chemistry), 10.21 (immunoassay techniques), 13.27 (coagulation), 26.06 (high-performance liquid chromatography), 21.2 (immunological), 3.85 (gases and electrolytes), 156.48 (cytogenetic), 1.38 (urine), 4.02 (automated hematological), 4.93 (manual hematological). The value, or service fee, returned to public institutions who perform laboratory services does not adequately reflect the true total average production costs of examinations.

  9. Cost-benefit analysis for a lead wheel weight phase-out in Canada.

    Science.gov (United States)

    Campbell, P M; Corneau, E; Nishimura, D; Teng, E; Ekoualla, D

    2018-05-06

    Lead wheel weights (LWWs) have been banned in Europe, and some US States, but they continue to dominate the market in Canada. Exposure to lead is associated with numerous health impacts and can result in multiple and irreversible health problems which include cognitive impairment when exposure occurs during early development. Such impacts incur high individual and social costs. The purpose of this study was to assess the costs and public health benefits of a Risk Management Strategy (RMS) that would result from a LWW phase-out in Canada and compare this to a Business-As-Usual (BAU) scenario. The contribution of LWWs to lead concentrations in media including roadway soil/dust, ambient and indoor air, and indoor dust were estimated. The Integrated Exposure Uptake Biokinetic Model for Lead in Children (IEUBK) was used to develop estimates for the blood lead levels (BLLs) in children (μg/dL) associated with the BAU and the RMS. The BLLs estimated via the IEUBK model were then used to assess the IQ decrements associated with the BAU that would be avoided under the RMS. The subsequent overall societal benefits in terms of increased lifetime earning potential and reduced crime rate, were then estimated and compared to industry and government costs. LWWs form 72% of the Canadian wheel weight market and >1500 tonnes of lead as new LWWs attached to vehicles enters Canadian society annually. We estimate that 110-131 tonnes of lead in detached WWs are abraded on roadways in Canada each year. A LWW phase-out was predicted to result in a drop in pre-school BLLs of up to 0.4 μg/dL. The estimated net benefits associated with the RMS based on cognitive decrements avoided and hence increased lifetime earning potential (increased productivity) and reduced crime are expected to be: C$248 million (8% discount rate) to C$1.2 billion (3% discount rate) per year. Copyright © 2018 Elsevier B.V. All rights reserved.

  10. Economic weights in rabbit meat production

    Directory of Open Access Journals (Sweden)

    L. Cartuche

    2014-09-01

    Full Text Available A profit function was designed for an industrial commercial rabbitry with the most common management in industrial rabbit production. The incomes, costs, and profit function were calculated and economic weights of the traits were estimated. The variable costs (feeding, artificial insemination, health and replacement represented 62% of the total costs, and the fixed costs (labour, utilities, amortisation and administration represented 38% of the total costs. Major costs were feeding of fattening kits and labour cost, at 26% and 18% of the total cost, respectively. The economic weights were feed conversion rate during fattening (–20.2 €/[g feed/g liveweight], number of kits born alive (15.7 €/kit, pregnancy rate (1.7 €/percentage unit, weaning survival (1.7 €/percentage unit, fattening survival (2.0 €/percentage unit, daily feed intake (–0.50 €/(g feed/d, daily gain during fattening (1.33 €/(g weight/d, and replacement rate (–0.29 €/percentage unit. When varying the prices of kg of fattening feed and kg of liveweight, only the economic weights of feed conversion rate during fattening in the first case and the number of kits born alive in the second case changed considerably. Changes in labour cost produced appreciable changes in the whole production cost. Although economic weights are robust to changes in prices, these weights should be recalculated after some generations of selection, because changes in the mean of the traits due to selection can also change economic weights.

  11. Activity-Based Costing Model for Assessing Economic Performance.

    Science.gov (United States)

    DeHayes, Daniel W.; Lovrinic, Joseph G.

    1994-01-01

    An economic model for evaluating the cost performance of academic and administrative programs in higher education is described. Examples from its application at Indiana University-Purdue University Indianapolis are used to illustrate how the model has been used to control costs and reengineer processes. (Author/MSE)

  12. Physical Protection System Upgrades - Optimizing for Performance and Cost

    International Nuclear Information System (INIS)

    Hicks, Mary Jane; Bouchard, Ann M.

    1999-01-01

    CPA--Cost and Performance Analysis--is an architecture that supports analysis of physical protection systems and upgrade options. ASSESS (Analytic System and Software for Evaluating Security Systems), a tool for evaluating performance of physical protection systems, currently forms the cornerstone for evaluating detection probabilities and delay times of the system. Cost and performance data are offered to the decision-maker at the systems level and to technologists at the path-element level. A new optimization engine has been attached to the CPA methodology to automate analyses of many combinations (portfolios) of technologies. That engine controls a new analysis sequencer that automatically modifies ASSESS PPS files (facility descriptions), automatically invokes ASSESS Outsider analysis and then saves results for post-processing. Users can constrain the search to an upper bound on total cost, to a lower bound on level of performance, or to include specific technologies or technology types. This process has been applied to a set of technology development proposals to identify those portfolios that provide the most improvement in physical security for the lowest cost to install, operate and maintain at a baseline facility

  13. Growth performance, haematology and cost benefit of growing rabbits reared on different feed access times and restriction durations

    Directory of Open Access Journals (Sweden)

    Obasa, O.A

    2016-06-01

    Full Text Available Sixty growing rabbits of mixed breeds and sexes were used for 10 wk in a 4 x 3 factorial experimental design to test for the effect of different feed access times (2, 4, 6 and 24 h and different restriction durations (2, 4 and 6 wk on the performance, haematological parameters and cost benefits of growing rabbits. Data obtained were subject to a 2�way analysis of variance. Results showed significantly higher (p0.05 across the feed access time and restriction duration. White blood cell was higher in growing rabbits on 2-h feed access time for 6-wk duration of restriction while all other parameters measured for haematology were not significantly affected by the feed access time and restriction duration. Total cost of feed consumed was highest in growing rabbits maintained on 24-h feed access time. Cost of feed per kg weight gain was not significantly influenced across the feed access times and the restriction durations. It was concluded that for a reduced cost of feeding without an adverse effect on the performance and haematological profile, growing rabbits should be raised on not less than 4-h feed access time for 2-wk restriction duration.

  14. The Economic Impact of Weight Regain

    Directory of Open Access Journals (Sweden)

    Caroline E. Sheppard

    2013-01-01

    Full Text Available Background. Obesity is well known for being associated with significant economic repercussions. Bariatric surgery is the only evidence-based solution to this problem as well as a cost-effective method of addressing the concern. Numerous authors have calculated the cost effectiveness and cost savings of bariatric surgery; however, to date the economic impact of weight regain as a component of overall cost has not been addressed. Methods. The literature search was conducted to elucidate the direct costs of obesity and primary bariatric surgery, the rate of weight recidivism and surgical revision, and any costs therein. Results. The quoted cost of obesity in Canada was $2.0 billion–$6.7 billion in 2013 CAD. The median percentage of bariatric procedures that fail due to weight gain or insufficient weight loss is 20% (average: 21.1%±10.1%, range: 5.2–39, n=10. Revision of primary surgeries on average ranges from 2.5% to 18.4%, and depending on the procedure accounts for an additional cost between $14,000 and $50,000 USD per patient. Discussion. There was a significant deficit of the literature pertaining to the cost of revision surgery as compared with primary bariatric surgery. As such, the cycle of weight recidivism and bariatric revisions has not as of yet been introduced into any previous cost analysis of bariatric surgery.

  15. A within-trial cost-effectiveness analysis of primary care referral to a commercial provider for weight loss treatment, relative to standard care—an international randomised controlled trial

    Science.gov (United States)

    Fuller, N R; Colagiuri, S; Schofield, D; Olson, A D; Shrestha, R; Holzapfel, C; Wolfenstetter, S B; Holle, R; Ahern, A L; Hauner, H; Jebb, S A; Caterson, I D

    2013-01-01

    Background: Due to the high prevalence of overweight and obesity there is a need to identify cost-effective approaches for weight loss in primary care and community settings. Objective: We evaluated the cost effectiveness of two weight loss programmes of 1-year duration, either standard care (SC) as defined by national guidelines, or a commercial provider (Weight Watchers) (CP). Design: This analysis was based on a randomised controlled trial of 772 adults (87% female; age 47.4±12.9 years; body mass index 31.4±2.6 kg m−2) recruited by health professionals in primary care in Australia, United Kingdom and Germany. Both a health sector and societal perspective were adopted to calculate the cost per kilogram of weight loss and the ICER, expressed as the cost per quality adjusted life year (QALY). Results: The cost per kilogram of weight loss was USD122, 90 and 180 for the CP in Australia, the United Kingdom and Germany, respectively. For SC the cost was USD138, 151 and 133, respectively. From a health-sector perspective, the ICER for the CP relative to SC was USD18 266, 12 100 and 40 933 for Australia, the United Kingdom and Germany, respectively. Corresponding societal ICER figures were USD31 663, 24 996 and 51 571. Conclusion: The CP was a cost-effective approach from a health funder and societal perspective. Despite participants in the CP group attending two to three times more meetings than the SC group, the CP was still cost effective even including these added patient travel costs. This study indicates that it is cost effective for general practitioners (GPs) to refer overweight and obese patients to a CP, which may be better value than expending public funds on GP visits to manage this problem. PMID:22929209

  16. Standing economy: does the heterogeneity in the energy cost of posture maintenance reside in differential patterns of spontaneous weight-shifting?

    Science.gov (United States)

    Miles-Chan, Jennifer L; Fares, Elie-Jacques; Berkachy, Redina; Jacquet, Philippe; Isacco, Laurie; Schutz, Yves; Montani, Jean-Pierre; Dulloo, Abdul G

    2017-04-01

    Due to sedentarity-associated disease risks, there is much interest in methods to increase low-intensity physical activity. In this context, it is widely assumed that altering posture allocation can modify energy expenditure (EE) to impact body-weight regulation and health. However, we have recently shown the existence of two distinct phenotypes pertaining to the energy cost of standing-with most individuals having no sustained increase in EE during steady-state standing relative to sitting comfortably. Here, we investigated whether these distinct phenotypes are related to the presence/absence of spontaneous "weight-shifting", i.e. the redistribution of body-weight from one foot to the other. Using indirect calorimetry to measure EE in young adults during sitting and 10 min of steady-state standing, we examined: (i) heterogeneity in EE during standing (n = 36); (ii) EE and spontaneous weight-shifting patterns (n = 18); (iii) EE during spontaneous weight-shifting versus experimentally induced weight-shifting (n = 7), and; (iv) EE during spontaneous weight-shifting versus intermittent leg/body displacement (n = 6). Despite heterogeneity in EE response to steady-state standing, no differences were found in the amount or pattern of spontaneous weight-shifting between the two phenotypes. Whilst experimentally induced weight-shifting resulted in a mean EE increase of only 11% (range: 0-25%), intermittent leg/body displacement increased EE to >1.5 METs in all participants. Although the variability in spontaneous weight-shifting signatures between individuals does not appear to underlie heterogeneity in the energy cost of standing posture maintenance, these studies underscore the fact that leg/body displacement, rather than standing posture alone, is needed to increase EE above the currently defined sedentary threshold.

  17. Flash memories economic principles of performance, cost and reliability optimization

    CERN Document Server

    Richter, Detlev

    2014-01-01

    The subject of this book is to introduce a model-based quantitative performance indicator methodology applicable for performance, cost and reliability optimization of non-volatile memories. The complex example of flash memories is used to introduce and apply the methodology. It has been developed by the author based on an industrial 2-bit to 4-bit per cell flash development project. For the first time, design and cost aspects of 3D integration of flash memory are treated in this book. Cell, array, performance and reliability effects of flash memories are introduced and analyzed. Key performance parameters are derived to handle the flash complexity. A performance and array memory model is developed and a set of performance indicators characterizing architecture, cost and durability is defined.   Flash memories are selected to apply the Performance Indicator Methodology to quantify design and technology innovation. A graphical representation based on trend lines is introduced to support a requirement based pr...

  18. Relationship between physical activity and physical performance in later life in different birth weight groups.

    Science.gov (United States)

    Jantunen, H; Wasenius, N S; Salonen, M K; Perälä, M-M; Kautiainen, H; Simonen, M; Pohjolainen, P; Kajantie, E; von Bonsdorff, M B; Eriksson, J G

    2018-02-01

    There is strong evidence that physical activity (PA) has an influence on physical performance in later life. Also, a small body size at birth has been associated with lower physical functioning in older age and both small and high birth weight have shown to be associated with lower leisure time physical activity. However, it is unknown whether size at birth modulates the association between PA and physical performance in old age. We examined 695 individuals from the Helsinki Birth Cohort Study born in Helsinki, Finland between 1934 and 1944. At a mean age of 70.7 years PA was objectively assessed with a multisensory activity monitor and physical performance with the Senior Fitness Test (SFT). Information on birth weight and gestational age was retrieved from hospital birth records. The study participants were divided in three birth weight groups, that is birth weight groups. However, the effect size of the association was large and significant only in men with a birth weight confidence interval 0.37-0.81, Pbirth weight. Our results suggest that men with low birth weight might benefit most from engaging in PA in order to maintain a better physical performance.

  19. IMPROVING PERFORMANCES BY USING COST CONTROLLING IN THE MINING INDUSTRY ENTITIES

    Directory of Open Access Journals (Sweden)

    SORINEL CĂPUŞNEANU

    2016-06-01

    Full Text Available The aim of this article is to highlight the improving performances of entities from mining industry entities by using cost controlling as an important tool of management accounting, applying the target costing method. The survey is based on questions that led investigation made in the Romanian entities from mining industry and based on data a thorough analysis was done for fulfillment of authors’ purpose. The results obtained by applying the target costing method has allowed a very strict cost control, which ultimately led to increased performances of economic entities from mining industry in Romania. The secondary purpose of this article is to try adjusting the target costing method to the specific of entities in the mining industry. According to studies of specialists this method based on target costing calculation is rather unusual in this sector of mining industry and it relies heavily on the activity-based costing method. The article ends with the authors' conclusions on improving the performances of entities from mining industry based on cost controlling and use of mix information obtained through the applied methods

  20. Effect of plyometric vs. dynamic weight training on the energy cost of running.

    Science.gov (United States)

    Berryman, Nicolas; Maurel, Delphine B; Bosquet, Laurent

    2010-07-01

    The purpose of this study is to compare the effects of 2 strength training methods on the energy cost of running (Cr). Thirty-five moderately to well-trained male endurance runners were randomly assigned to either a control group (C) or 2 intervention groups. All groups performed the same endurance-training program during an 8-week period. Intervention groups added a weekly strength training session designed to improve neuromuscular qualities. Sessions were matched for volume and intensity using either plyometric training (PT) or purely concentric contractions with added weight (dynamic weight training [DWT]). We found an interaction between time and group (p < 0.05) and an effect of time (p < 0.01) for Cr. Plyometric training induced a larger decrease of Cr (218 +/- 16 to 203 +/- 13 ml.kg.km) than DWT (207 +/- 15 to 199 +/- 12 ml.kg.km), whereas it remained unchanged in C. Pre-post changes in Cr were correlated with initial Cr (r = -0.57, p < 0.05). Peak vertical jump height (VJHpeak) increased significantly (p < 0.01) for both experimental groups (DWT = 33.4 +/- 6.2 to 34.9 +/- 6.1 cm, PT = 33.3 +/- 4.0 to 35.3 +/- 3.6 cm) but not for C. All groups showed improvements (p < 0.05) in Perf3000 (C = 711 +/- 107 to 690 +/- 109 seconds, DWT = 755 +/- 87 to 724 +/- 77 seconds, PT = 748 +/- 81 to 712 +/- 76 seconds). Plyometric training were more effective than DWT in improving Cr in moderately to well-trained male endurance runners showing that athletes and coaches should include explosive strength training in their practices with a particular attention on plyometric exercises. Future research is needed to establish the origin of this adaptation.

  1. Increased body weight affects academic performance in university students

    Directory of Open Access Journals (Sweden)

    Angela S. Anderson

    2017-03-01

    Full Text Available For K-12 students, obesity has been linked to student educational achievements. The study objective was to determine whether academic performance in university students is correlated with BMI. Students from two consecutive academic years (Jan–May 2013 and Jan–May 2014 were given an optional class survey in May, as extra credit. Of the 452 students that completed the survey, 204 females and 75 males (N = 279; 73% female and 27% male consented to participate in the study. The number of correct answers to problem-solving questions (PSQs and the overall final grade for the class were compared to the calculated BMI using linear regression with a Pearson's R correlation and unpaired t-tests. BMI was significantly negatively correlated with student's final grades (P = 0.001 Pearson's r = −0.190 and PSQs were positively correlated with final grades (P < 0.001; Pearson's r = 0.357. Our findings show a correlation between healthy body weight and improved academic performance. Further, the data suggest that future research in the area of body weight, diet, and exercise and any correlations of these with academic performance in college students are warranted.

  2. Compact, Light-weight and Cost-effective Microscope based on Lensless Incoherent Holography for Telemedicine Applications

    Science.gov (United States)

    Mudanyali, Onur; Tseng, Derek; Oh, Chulwoo; Isikman, Serhan O.; Sencan, Ikbal; Bishara, Waheb; Oztoprak, Cetin; Seo, Sungkyu; Khademhosseini, Bahar; Ozcan, Aydogan

    2010-01-01

    Despite the rapid progress in optical imaging, most of the advanced microscopy modalities still require complex and costly set-ups that unfortunately limit their use beyond well equipped laboratories. In the meantime, microscopy in resource-limited settings has requirements significantly different from those encountered in advanced laboratories, and such imaging devices should be cost-effective, compact, light-weight and appropriately accurate and simple to be usable by minimally trained personnel. Furthermore, these portable microscopes should ideally be digitally integrated as part of a telemedicine network that connects various mobile health-care providers to a central laboratory or hospital. Toward this end, here we demonstrate a lensless on-chip microscope weighing ~46 grams with dimensions smaller than 4.2cm × 4.2cm × 5.8cm that achieves sub-cellular resolution over a large field of view of ~24 mm2. This compact and light-weight microscope is based on digital in-line holography and does not need any lenses, bulky optical/mechanical components or coherent sources such as lasers. Instead, it utilizes a simple light-emitting-diode (LED) and a compact opto-electronic sensor-array to record lensless holograms of the objects, which then permits rapid digital reconstruction of regular transmission or differential interference contrast (DIC) images of the objects. Because this lensless incoherent holographic microscope has orders-of-magnitude improved light collection efficiency and is very robust to mechanical misalignments it may offer a cost-effective tool especially for telemedicine applications involving various global health problems in resource limited settings. PMID:20401422

  3. Low cost high performance uncertainty quantification

    KAUST Repository

    Bekas, C.

    2009-01-01

    Uncertainty quantification in risk analysis has become a key application. In this context, computing the diagonal of inverse covariance matrices is of paramount importance. Standard techniques, that employ matrix factorizations, incur a cubic cost which quickly becomes intractable with the current explosion of data sizes. In this work we reduce this complexity to quadratic with the synergy of two algorithms that gracefully complement each other and lead to a radically different approach. First, we turned to stochastic estimation of the diagonal. This allowed us to cast the problem as a linear system with a relatively small number of multiple right hand sides. Second, for this linear system we developed a novel, mixed precision, iterative refinement scheme, which uses iterative solvers instead of matrix factorizations. We demonstrate that the new framework not only achieves the much needed quadratic cost but in addition offers excellent opportunities for scaling at massively parallel environments. We based our implementation on BLAS 3 kernels that ensure very high processor performance. We achieved a peak performance of 730 TFlops on 72 BG/P racks, with a sustained performance 73% of theoretical peak. We stress that the techniques presented in this work are quite general and applicable to several other important applications. Copyright © 2009 ACM.

  4. High specification starter diets improve the performance of low birth weight pigs to 10 weeks of age.

    Science.gov (United States)

    Douglas, S L; Wellock, I; Edwards, S A; Kyriazakis, I

    2014-10-01

    Piglets born with low birth weights (LBiW) are likely to be lighter at weaning. Starter regimes tailored for pigs of average BW therefore may not be optimal for LBiW nursery performance. The objective was to determine if LBiW pigs benefit from a high specification starter regime and the provision of extra feed (additional allowance of last phase diet of the starter regime) in comparison to a standard commercial regime. Additionally, the effect of starter regime on performance of normal birth weight (NBiW) pigs at weaning was determined and compared to that of LBiW pigs. Finally, the cost effectiveness of the treatments was determined. The experiment was therefore an incomplete 2 × 2 × 2 factorial design, as the provision of extra feed was given only to LBiW pigs (n = 6 replicates per treatment; 5 pigs per replicate). Treatments comprised birth weight (LBiW or NBiW), starter regime (high specification [HS] or standard starter [SS]), and extra feed 3 quantity (yes [YF] or no [NF], for LBiW pigs only; feed 3 corresponded to the last phase diet of the starter regime). At weaning (d 28), pigs were randomly assigned within each birth weight category to treatment groups. Nutritional treatments were fed ad libitum on a kilogram/head basis for approximately 3 wk followed by a common weaner diet fed ad libitum until d 70. Starter regime (P = 0.019), feed 3 amount (P = 0.010), and their interaction (P = 0.029) had an effect on ADG of LBiW pigs from d 28 to 49, with pigs on HS followed by YF (HY) performing best. An improvement in feed conversion ratio (FCR) was noted between d 28 and 49 for pigs fed the additional feed 3 (P = 0.030); between d 49 and 70, the only residual effect seen was of starter regime (P = 0.017) on ADG. In contrast, there was no significant effect of starter regime from d 28 to 70 on ADG, ADFI, or FCR of NBiW pigs. By d 49 and 70, LBiW pigs on regime HY weighed the same as NBiW pigs (d 70 BW; 30.0 vs. 30.6 kg; P = 0.413), with similar growth rates from

  5. Derivation of weighting factors for cost and radiological impact for use in comparison of waste management methods

    International Nuclear Information System (INIS)

    Allen, P.T.; Lee, T.R.

    1991-01-01

    Nuclear waste management decisions are complex, and must include considerations of cost and social factors in addition to dose limitation. Decision-aiding techniques, such as multi-attribute analysis, can assist in structuring the problem and can icorporate as many factors, or attributes, as required. However, the relative weights of such attributes need to be established. Methods were devised which could be compared with one another. These were questionnaire-based but, in order to examine the possible influence of the measurement procedures on the results, two of the methods were combined in an experimental design. The two direct methods for obtaining weights (the conventional rating scales and the direct rating task) showed good agreement and yielded different values for separate social groups, such as industrial employees and lay public. The main conclusion is that the elicitation of weighting factors from the public is possible and that the resulting weights are meaningful and could have significant effects on the choice of waste management options

  6. Intentional Weight Loss Improved Performance in Obese Ischaemic Heart Patient

    DEFF Research Database (Denmark)

    Geiker, Nina; Myint, Khin Swe; Heck, Patrick

    2014-01-01

    Aims: The risk of heart failure (HF) increases with BMI, but paradoxically obesity has been associated with reduced mortality in patients with HF. The effect of intentional or therapeutic weight loss on HF is not well known. We examined the effect of weight loss induced by low energy diet (LED......) on physical performance and cardiovascular risk factors in obese patients with moderate-to-severe HF and/or ischaemic heart disease (IHD). Methods and Results: Results from two weight loss interventions at two centres, one in Denmark (DK - 12 week intervention in 21 subjects (14 LED, 7 controls)) and one.......1 in the intervention group versus -22.1% ± 25.6 in the control group (P=0.000). Treatment also improved triglycerides (P=0.000), very low lipoprotein (P=0.001) and C-reactive protein (P=0.010). Conclusion: Weight loss induced by LED in obese patients with moderate-to-severe HF or IHD resulted in clinically significant...

  7. Selecting an Architecture for a Safety-Critical Distributed Computer System with Power, Weight and Cost Considerations

    Science.gov (United States)

    Torres-Pomales, Wilfredo

    2014-01-01

    This report presents an example of the application of multi-criteria decision analysis to the selection of an architecture for a safety-critical distributed computer system. The design problem includes constraints on minimum system availability and integrity, and the decision is based on the optimal balance of power, weight and cost. The analysis process includes the generation of alternative architectures, evaluation of individual decision criteria, and the selection of an alternative based on overall value. In this example presented here, iterative application of the quantitative evaluation process made it possible to deliberately generate an alternative architecture that is superior to all others regardless of the relative importance of cost.

  8. Strategic cost management, contingent factors and performance in services

    Directory of Open Access Journals (Sweden)

    Odysseas Pavlatos

    2018-06-01

    Full Text Available The purpose of this paper is to investigate the relationship between contextual factors identified from contingency-based research, the extent of the use of strategic cost management (SCM techniques and business performance in services. An empirical survey was conducted on a sample of 88 services in Greece. The analysis of the survey data indicates that the use of strategic cost management techniques in services can be considered quite satisfactory. By drawing on the grounds of contingency theory, five factors were identified as potentially exhibiting an emergent relationship with strategic cost management. The five factors are; (1 Perceived environmental uncertainty, (2 Structure, (3 Organizational life cycle stage, (4 Strategy and (5 Size. The survey revealed that SCM usage is positively affected by these five contingent factors, while SCM usage, in turn, positively affects performance. A significant mediating effect of SCM usage on performance is evident.

  9. Cost analysis and economic comparison for alternative fuel cycles in the heavy water cooled canadian reactor (CANDU)

    International Nuclear Information System (INIS)

    Yilmaz, S.

    2000-01-01

    Three main options in a CANDU fuel cycle involve use of: (1) natural uranium (0.711 weight percent U-235) fuel, (2) slightly enriched uranium (1.2 weight percent U-235) fuel, and (3) recovered uranium (0.83 weight percent U-235) fuel from light water reactor spent fuel. ORIGEN-2 computer code was used to identify composition of the spent fuel for each option, including the standard LWR fuel (3.3 weight percent U-235). Uranium and plutonium credit calculations were performed using ORIGEN-2 output. WIMSD-5 computer code was used to determine maximum discharge burnup values for each case. For the 3 cycles selected (natural uranium, slightly enriched uranium, recovered uranium), levelized fuel cycle cost calculations are performed over the reactor lifetime of 40 years, using unit process costs obtained from literature. Components of the fuel cycle costs are U purchase, conversion, enrichment, fabrication, SF storage, SF disposal, and reprocessing where applicable. Cost parameters whose effects on the fuel cycle cost are to be investigated are escalation ratio, discount rate and SF storage time. Cost estimations were carried out using specially developed computer programs. Share of each cost component on the total cost was determined and sensitivity analysis was performed in order to show how a change in a main cost component affects the fuel cycle cost. The main objective of this study has been to find out the most economical option for CANDU fuel cycle by changing unit prices and cost parameters

  10. Computerized cost estimation spreadsheet and cost data base for fusion devices

    International Nuclear Information System (INIS)

    Hamilton, W.R.; Rothe, K.E.

    1985-01-01

    An automated approach to performing and cataloging cost estimates has been developed at the Fusion Engineering Design Center (FEDC), wherein the cost estimate record is stored in the LOTUS 1-2-3 spreadsheet on an IBM personal computer. The cost estimation spreadsheet is based on the cost coefficient/cost algorithm approach and incorporates a detailed generic code of cost accounts for both tokamak and tandem mirror devices. Component design parameters (weight, surface area, etc.) and cost factors are input, and direct and indirect costs are calculated. The cost data base file derived from actual cost experience within the fusion community and refined to be compatible with the spreadsheet costing approach is a catalog of cost coefficients, algorithms, and component costs arranged into data modules corresponding to specific components and/or subsystems. Each data module contains engineering, equipment, and installation labor cost data for different configurations and types of the specific component or subsystem. This paper describes the assumptions, definitions, methodology, and architecture incorporated in the development of the cost estimation spreadsheet and cost data base, along with the type of input required and the output format

  11. An opportunity cost model of subjective effort and task performance

    Science.gov (United States)

    Kurzban, Robert; Duckworth, Angela; Kable, Joseph W.; Myers, Justus

    2013-01-01

    Why does performing certain tasks cause the aversive experience of mental effort and concomitant deterioration in task performance? One explanation posits a physical resource that is depleted over time. We propose an alternate explanation that centers on mental representations of the costs and benefits associated with task performance. Specifically, certain computational mechanisms, especially those associated with executive function, can be deployed for only a limited number of simultaneous tasks at any given moment. Consequently, the deployment of these computational mechanisms carries an opportunity cost – that is, the next-best use to which these systems might be put. We argue that the phenomenology of effort can be understood as the felt output of these cost/benefit computations. In turn, the subjective experience of effort motivates reduced deployment of these computational mechanisms in the service of the present task. These opportunity cost representations, then, together with other cost/benefit calculations, determine effort expended and, everything else equal, result in performance reductions. In making our case for this position, we review alternate explanations both for the phenomenology of effort associated with these tasks and for performance reductions over time. Likewise, we review the broad range of relevant empirical results from across subdisciplines, especially psychology and neuroscience. We hope that our proposal will help to build links among the diverse fields that have been addressing similar questions from different perspectives, and we emphasize ways in which alternate models might be empirically distinguished. PMID:24304775

  12. Performance of an area variable MOS varicap weighted programmable CCD transversal filter

    OpenAIRE

    Bhattacharyya, A.B.; Shankarnarayan, L.; Kapur, N.; Wallinga, Hans

    1981-01-01

    The performance of an electrically programmable CCD transversal filter (PTF) is presented in which tap-weight multiplication is performed by a novel and compact on chip voltage controlled area variable MOS varicap.

  13. Whole Building Cost and Performance Measurement: Data Collection Protocol Revision 2

    Energy Technology Data Exchange (ETDEWEB)

    Fowler, Kimberly M.; Spees, Kathleen L.; Kora, Angela R.; Rauch, Emily M.; Hathaway, John E.; Solana, Amy E.

    2009-03-27

    This protocol was written for the Department of Energy’s Federal Energy Management Program (FEMP) to be used by the public as a tool for assessing building cost and performance measurement. The primary audiences are sustainable design professionals, asset owners, building managers, and research professionals within the Federal sector. The protocol was developed based on the need for measured performance and cost data on sustainable design projects. Historically there has not been a significant driver in the public or private sector to quantify whole building performance in comparable terms. The deployment of sustainable design into the building sector has initiated many questions on the performance and operational cost of these buildings.

  14. Cardiorespiratory performance and physical activity in normal weight and overweight Finnish adolescents from 2003 to 2010.

    Science.gov (United States)

    Palomäki, Sanna; Heikinaro-Johansson, Pilvikki; Huotari, Pertti

    2015-01-01

    We investigated changes in cardiorespiratory performance, BMI and leisure-time physical activity among Finnish adolescents from 2003 to 2010. In addition, we compared cardiorespiratory performance levels between normal weight and overweight adolescents, grouped according to their physical activity. Participants were a national representative samples of 15-16-year-old adolescents in their final (ninth) year of comprehensive school in 2003 (n = 2258) and in 2010 (n = 1301). They performed an endurance shuttle run test and reported their height and weight and leisure time physical activity on a questionnaire. Results showed no significant secular changes in cardiorespiratory performance from 2003 to 2010. The mean BMI increased in boys. Leisure-time physical activity increased among normal weight girls. Adolescents of normal weight had better cardiorespiratory performance than those classified as overweight at both assessment points. BMI-adjusted physical activity was a significant determinant for cardiorespiratory performance among overweight adolescents, and very active overweight adolescents had similar cardiorespiratory performance levels as moderately active adolescents of normal weight. The results of the present study support the idea that the physical activity has the great importance for the cardiorespiratory performance in adolescents. Overweight adolescents, in particular, benefit from higher levels of physical activity.

  15. Building Energy and Cost Performance: An Analysis of Thirty Melbourne Case Studies

    Directory of Open Access Journals (Sweden)

    Yu Lay Langston

    2012-11-01

    Full Text Available This study investigates the energy and cost performance of thirty recent buildings in Melbourne, Australia. Commonly, building design decisions are based on issues pertaining to construction cost, and consideration of energy performance is made only within the context of the initial project budget. Even where energy is elevated to more importance, operating energy is seen as the focus and embodied energy is nearly always ignored. For the first time, a large sample of buildings has been assembled and analyzed to improve the understanding of both energy and cost performance over their full life cycle, which formed the basis of a wider doctoral study into the inherent relationship between energy and cost. The aim of this paper is to report on typical values for embodied energy, operating energy, capital cost and operating cost per square metre for a range of building functional types investigated in this research. The conclusion is that energy and cost have quite different profiles across projects, and yet the mean GJ/m2 or cost/m2 have relatively low coefficients of variation and therefore may be useful as benchmarks of typical building performance.  

  16. [Pay for performance explained by transaction costs theory].

    Science.gov (United States)

    Gorbaneff, Yuri; Cortes, Ariel; Torres, Sergio; Yepes, Francisco

    2011-01-01

    To evaluate the ability of transaction costs theory to explain incentives in the health care chain. We performed a case study of CPS, a health insurance company in Bogota (Colombia), which preferred not to publish its name. CPS moves in the environment of high transaction costs and uses the hybrid form of governance at the outpatient level. Incentive intensity, administrative control and the contract all agree with the theory. At the hospital level, the market is used, despite greater uncertainty. Because of the discrete form (1.0) of the incentives and the absence of administrative control, it is difficult for CPS to relate payment to hospital performance. Transaction costs theory explains the configuration of incentives. Another contribution made by this theory to the literature is the criterion to differentiate between the market and the hybrid. We propose that the market uses discrete-type (1.0) incentives, while the hybrid uses continuous, commission-like incentives. Copyright © 2011 SESPAS. Published by Elsevier Espana. All rights reserved.

  17. Occupational-Specific Strength Predicts Astronaut-Related Task Performance in a Weighted Suit.

    Science.gov (United States)

    Taylor, Andrew; Kotarsky, Christopher J; Bond, Colin W; Hackney, Kyle J

    2018-01-01

    Future space missions beyond low Earth orbit will require deconditioned astronauts to perform occupationally relevant tasks within a planetary spacesuit. The prediction of time-to-completion (TTC) of astronaut tasks will be critical for crew safety, autonomous operations, and mission success. This exploratory study determined if the addition of task-specific strength testing to current standard lower body testing would enhance the prediction of TTC in a 1-G test battery. Eight healthy participants completed NASA lower body strength tests, occupationally specific strength tests, and performed six task simulations (hand drilling, construction wrenching, incline walking, collecting weighted samples, and dragging an unresponsive crewmember to safety) in a 48-kg weighted suit. The TTC for each task was recorded and summed to obtain a total TTC for the test battery. Linear regression was used to predict total TTC with two models: 1) NASA lower body strength tests; and 2) NASA lower body strength tests + occupationally specific strength tests. Total TTC of the test battery ranged from 20.2-44.5 min. The lower body strength test alone accounted for 61% of the variability in total TTC. The addition of hand drilling and wrenching strength tests accounted for 99% of the variability in total TTC. Adding occupationally specific strength tests (hand drilling and wrenching) to standard lower body strength tests successfully predicted total TTC in a performance test battery within a weighted suit. Future research should couple these strength tests with higher fidelity task simulations to determine the utility and efficacy of task performance prediction.Taylor A, Kotarsky CJ, Bond CW, Hackney KJ. Occupational-specific strength predicts astronaut-related task performance in a weighted suit. Aerosp Med Hum Perform. 2018; 89(1):58-62.

  18. Cardiorespiratory fitness and academic performance association is mediated by weight status in adolescents: DADOS study.

    Science.gov (United States)

    Beltran-Valls, María Reyes; Adelantado-Renau, Mireia; Castro-Piñero, Jose; Sánchez-López, Mairena; Moliner-Urdiales, Diego

    2018-04-28

    The aim of our study was to examine the mediation effect of weight status on the association between cardiorespiratory fitness (CRF) and academic performance (AP). Two hundred sixty-nine adolescents (140 boys) aged 13.9 ± 0.3 years old from the DADOS study were included in this cross-sectional analysis. CRF was assessed by the 20-m shuttle run test and estimated maximum oxygen uptake was used in the analysis. AP was assessed through the final academic grades and the Science Research Associates Test of Educational Abilities for assessing reasoning, verbal, and numeric abilities. Weight status was assessed by body mass index (kg/m 2 ). Boot-strapped mediation procedures were performed and indirect effects (IE) with confidence intervals (CI) not including zero were considered statistically significant. Mediation analysis revealed that weight status acted as a mediator of the relationship of CRF with reasoning ability (IE = 0.039; CI = 0.001; 0.091) and the final grades in Math (IE = 0.011; CI = 0.002; 0.025), Language (IE = 0.013; CI = 0.004; 0.027), and GPA (IE = 0.011; CI = 0.003; 0.023). Our data show that the influence of CRF on academic performance is mediated by weight status in adolescents. We suggest that our data could be considered by educators, families, and policy makers, so that active lifestyles might be promoted when designing programs aimed to improve AP among adolescents. What is Known: • Academic performance is associated with both, cardiorespiratory fitness and weight status. • The role of weight status in the association between cardiorespiratory fitness and academic performance is poorly understood. What is New: • We support the scarce research investigating the mediating role of weight status as mechanism in the association between fitness and academic performance in youth. • Previous knowledge is expanded by suggesting that cardiorespiratory fitness is related to weight status which in turn may

  19. Performance-based, cost- and time-effective PCB analytical methodology

    International Nuclear Information System (INIS)

    Alvarado, J. S.

    1998-01-01

    Laboratory applications for the analysis of PCBs (polychlorinated biphenyls) in environmental matrices such as soil/sediment/sludge and oil/waste oil were evaluated for potential reduction in waste, source reduction, and alternative techniques for final determination. As a consequence, new procedures were studied for solvent substitution, miniaturization of extraction and cleanups, minimization of reagent consumption, reduction of cost per analysis, and reduction of time. These new procedures provide adequate data that meet all the performance requirements for the determination of PCBs. Use of the new procedures reduced costs for all sample preparation techniques. Time and cost were also reduced by combining the new sample preparation procedures with the power of fast gas chromatography. Separation of Aroclor 1254 was achieved in less than 6 min by using DB-1 and SPB-608 columns. With the greatly shortened run times, reproducibility can be tested quickly and consequently with low cost. With performance-based methodology, the applications presented here can be applied now, without waiting for regulatory approval

  20. Chain-loaded variable resistance warm-up improves free-weight maximal back squat performance.

    Science.gov (United States)

    Mina, Minas A; Blazevich, Anthony J; Giakas, Giannis; Seitz, Laurent B; Kay, Anthony D

    2016-11-01

    The acute influence of chain-loaded variable resistance exercise on subsequent free-weight one-repetition maximum (1-RM) back squat performance was examined in 16 recreationally active men. The participants performed either a free-weight resistance (FWR) or chain-loaded resistance (CLR) back squat warm-up at 85% 1-RM on two separate occasions. After a 5-min rest, the participants attempted a free-weight 1-RM back squat; if successful, subsequent 5% load additions were made until participants failed to complete the lift. During the 1-RM trials, 3D knee joint kinematics and knee extensor and flexor electromyograms (EMG) were recorded simultaneously. Significantly greater 1-RM (6.2 ± 5.0%; p  .05) was found in concentric EMG, eccentric or concentric knee angular velocity, or peak knee flexion angle. Performing a CLR warm-up enhanced subsequent free-weight 1-RM performance without changes in knee flexion angle or eccentric and concentric knee angular velocities; thus a real 1-RM increase was achieved as the mechanics of the lift were not altered. These results are indicative of a potentiating effect of CLR in a warm-up, which may benefit athletes in tasks where high-level strength is required.

  1. A high-performance, low-cost, leading edge discriminator

    Indian Academy of Sciences (India)

    Abstract. A high-performance, low-cost, leading edge discriminator has been designed with a timing performance comparable to state-of-the-art, commercially available discrim- inators. A timing error of 16 ps is achieved under ideal operating conditions. Under more realistic operating conditions the discriminator displays a ...

  2. Using performance indicators to reduce cost uncertainty of China's CO2 mitigation goals

    International Nuclear Information System (INIS)

    Xu, Yuan

    2013-01-01

    Goals on absolute emissions and intensity play key roles in CO 2 mitigation. However, like cap-and-trade policies with price uncertainty, they suffer from significant uncertainty in abatement costs. This article examines whether an indicator could be established to complement CO 2 mitigation goals and help reduce cost uncertainty with a particular focus on China. Performance indicators on CO 2 emissions per unit of energy consumption could satisfy three criteria: compared with the mitigation goals, (i) they are more closely associated with active mitigation efforts and (ii) their baselines have more stable projections from historical trajectories. (iii) Their abatement costs are generally higher than other mitigation methods, particularly energy efficiency and conservation. Performance indicators could be used in the following way: if a CO 2 goal on absolute emissions or intensity is attained, the performance indicator should still reach a lower threshold as a cost floor. If the goal cannot be attained, an upper performance threshold should be achieved as a cost ceiling. The narrower cost uncertainty may encourage wider and greater mitigation efforts. - Highlights: ► CO 2 emissions per unit of energy consumption could act as performance indicators. ► Performance indicators are more closely related to active mitigation activities. ► Performance indicators have more stable historical trajectories. ► Abatement costs are higher for performance indicators than for other activities. ► Performance thresholds could reduce the cost uncertainty of CO 2 mitigation goals.

  3. Comparison of alternative weight recalibration methods for diagnosis-related groups

    Science.gov (United States)

    Rogowski, Jeannette Roskamp; Byrne, Daniel J.

    1990-01-01

    In this article, alternative methodologies for recalibration of the diagnosis-related group (DRG) weights are examined. Based on 1984 data, cost and charge-based weights are less congruent than those calculated with 1981 data. Previous studies using 1981 data demonstrated that cost- and charge-based weights were not very different. Charge weights result in higher payments to surgical DRGs and lower payments to medical DRGs, relative to cost weights. At the provider level, charge weights result in higher payments to large urban hospitals and teaching hospitals, relative to cost weights. PMID:10113568

  4. The Effects of Low Birth Weight on School Performance and Behavioral Outcomes of Elementary School Children in Oman

    Directory of Open Access Journals (Sweden)

    M. Mazharul Islam

    2015-07-01

    Full Text Available Objectives: Our study aimed to examine the effects of low birth weight (LBW on the school performance and behavior of elementary school children in Oman. Methods: Data were gathered through a cross-sectional survey of nine elementary schools from the Muscat and A’Dhahirah regions. The study utilized a unique database created by linking information from the children’s health cards and current academic and behavioral performance records. Information on children’s performance in various areas such as language, mathematics, science, information technology, sports, and behavior were obtained from the school registers. Birth weight (BW and selected sociodemographic data were obtained from the copy of their health cards kept by each school. A total of 542 elementary school children aged 7–11 years, who had completed grades 2–4, were surveyed.  Results: Data from the school register revealed a very high rate (17.7% of LBW and, overall, 12% of the children exhibited below average performance on selected outcome measures. The below average school performance varied from 5–17% across the six selected areas of school performance. The highest rate of below average performance was observed in science (17%, followed by arithmetic and language (16% each. BW showed significant differential effects on school performance and behavioral outcomes, which remained significant after controlling for the effect of potential confounders. It was found that LBW children were 2–6 times more likely to have poorer school performance in all areas than their normal BW peers. Conclusion: Early intervention programs or special care for LBW children in school could be an effective means of improving educational outcomes and the behavior of these children. Attempts should be made to reduce or prevent poor pregnancy outcomes, which, in turn, would reduce the cost of the health, education, and social services systems.

  5. CO2 control technology effects on IGCC plant performance and cost

    International Nuclear Information System (INIS)

    Chen Chao; Rubin, Edward S.

    2009-01-01

    As part of the USDOE's Carbon Sequestration Program, an integrated modeling framework has been developed to evaluate the performance and cost of alternative carbon capture and storage (CCS) technologies for fossil-fueled power plants in the context of multi-pollutant control requirements. This paper uses the newly developed model of an integrated gasification combined cycle (IGCC) plant to analyze the effects of adding CCS to an IGCC system employing a GE quench gasifier with water gas shift reactors and a Selexol system for CO 2 capture. Parameters of interest include the effects on plant performance and cost of varying the CO 2 removal efficiency, the quality and cost of coal, and selected other factors affecting overall plant performance and cost. The stochastic simulation capability of the model is also used to illustrate the effect of uncertainties or variability in key process and cost parameters. The potential for advanced oxygen production and gas turbine technologies to reduce the cost and environmental impacts of IGCC with CCS is also analyzed

  6. Automated packaging platform for low-cost high-performance optical components manufacturing

    Science.gov (United States)

    Ku, Robert T.

    2004-05-01

    Delivering high performance integrated optical components at low cost is critical to the continuing recovery and growth of the optical communications industry. In today's market, network equipment vendors need to provide their customers with new solutions that reduce operating expenses and enable new revenue generating IP services. They must depend on the availability of highly integrated optical modules exhibiting high performance, small package size, low power consumption, and most importantly, low cost. The cost of typical optical system hardware is dominated by linecards that are in turn cost-dominated by transmitters and receivers or transceivers and transponders. Cost effective packaging of optical components in these small size modules is becoming the biggest challenge to be addressed. For many traditional component suppliers in our industry, the combination of small size, high performance, and low cost appears to be in conflict and not feasible with conventional product design concepts and labor intensive manual assembly and test. With the advent of photonic integration, there are a variety of materials, optics, substrates, active/passive devices, and mechanical/RF piece parts to manage in manufacturing to achieve high performance at low cost. The use of automation has been demonstrated to surpass manual operation in cost (even with very low labor cost) as well as product uniformity and quality. In this paper, we will discuss the value of using an automated packaging platform.for the assembly and test of high performance active components, such as 2.5Gb/s and 10 Gb/s sources and receivers. Low cost, high performance manufacturing can best be achieved by leveraging a flexible packaging platform to address a multitude of laser and detector devices, integration of electronics and handle various package bodies and fiber configurations. This paper describes the operation and results of working robotic assemblers in the manufacture of a Laser Optical Subassembly

  7. Lamb Production Costs: Analyses of Composition and Elasticities Analysis of Lamb Production Costs

    Directory of Open Access Journals (Sweden)

    C. Raineri

    2015-08-01

    Full Text Available Since lamb is a commodity, producers cannot control the price of the product they sell. Therefore, managing production costs is a necessity. We explored the study of elasticities as a tool for basing decision-making in sheep production, and aimed at investigating the composition and elasticities of lamb production costs, and their influence on the performance of the activity. A representative sheep production farm, designed in a panel meeting, was the base for calculation of lamb production cost. We then performed studies of: i costs composition, and ii cost elasticities for prices of inputs and for zootechnical indicators. Variable costs represented 64.15% of total cost, while 21.66% were represented by operational fixed costs, and 14.19% by the income of the factors. As for elasticities to input prices, the opportunity cost of land was the item to which production cost was more sensitive: a 1% increase in its price would cause a 0.2666% increase in lamb cost. Meanwhile, the impact of increasing any technical indicator was significantly higher than the impact of rising input prices. A 1% increase in weight at slaughter, for example, would reduce total cost in 0.91%. The greatest obstacle to economic viability of sheep production under the observed conditions is low technical efficiency. Increased production costs are more related to deficient zootechnical indexes than to high expenses.

  8. A systems engineering cost analysis capability for use in assessing nuclear waste management system cost performance

    International Nuclear Information System (INIS)

    Shay, M.R.

    1990-04-01

    The System Engineering Cost Analysis (SECA) capability has been developed by the System Integration Branch of the US Department of Energy's Office of Civilian Radioactive Waste Management for use in assessing the cost performance of alternative waste management system configurations. The SECA capability is designed to provide rapid cost estimates of the waste management system for a given operational scenario and to permit aggregate or detailed cost comparisons for alternative waste system configurations. This capability may be used as an integral part of the System Integration Modeling System (SIMS) or, with appropriate input defining a scenario, as a separate cost analysis model

  9. Performance and cost of materials for lithium-based rechargeable automotive batteries

    Science.gov (United States)

    Schmuch, Richard; Wagner, Ralf; Hörpel, Gerhard; Placke, Tobias; Winter, Martin

    2018-04-01

    It is widely accepted that for electric vehicles to be accepted by consumers and to achieve wide market penetration, ranges of at least 500 km at an affordable cost are required. Therefore, significant improvements to lithium-ion batteries (LIBs) in terms of energy density and cost along the battery value chain are required, while other key performance indicators, such as lifetime, safety, fast-charging ability and low-temperature performance, need to be enhanced or at least sustained. Here, we review advances and challenges in LIB materials for automotive applications, in particular with respect to cost and performance parameters. The production processes of anode and cathode materials are discussed, focusing on material abundance and cost. Advantages and challenges of different types of electrolyte for automotive batteries are examined. Finally, energy densities and costs of promising battery chemistries are critically evaluated along with an assessment of the potential to fulfil the ambitious targets of electric vehicle propulsion.

  10. Cost/Performance Ratio Achieved by Using a Commodity-Based Cluster

    Science.gov (United States)

    Lopez, Isaac

    2001-01-01

    Researchers at the NASA Glenn Research Center acquired a commodity cluster based on Intel Corporation processors to compare its performance with a traditional UNIX cluster in the execution of aeropropulsion applications. Since the cost differential of the clusters was significant, a cost/performance ratio was calculated. After executing a propulsion application on both clusters, the researchers demonstrated a 9.4 cost/performance ratio in favor of the Intel-based cluster. These researchers utilize the Aeroshark cluster as one of the primary testbeds for developing NPSS parallel application codes and system software. The Aero-shark cluster provides 64 Intel Pentium II 400-MHz processors, housed in 32 nodes. Recently, APNASA - a code developed by a Government/industry team for the design and analysis of turbomachinery systems was used for a simulation on Glenn's Aeroshark cluster.

  11. Benchmarking whole-building energy performance with multi-criteria technique for order preference by similarity to ideal solution using a selective objective-weighting approach

    International Nuclear Information System (INIS)

    Wang, Endong

    2015-01-01

    Highlights: • A TOPSIS based multi-criteria whole-building energy benchmarking is developed. • A selective objective-weighting procedure is used for a cost-accuracy tradeoff. • Results from a real case validated the benefits of the presented approach. - Abstract: This paper develops a robust multi-criteria Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) based building energy efficiency benchmarking approach. The approach is explicitly selective to address multicollinearity trap due to the subjectivity in selecting energy variables by considering cost-accuracy trade-off. It objectively weights the relative importance of individual pertinent efficiency measuring criteria using either multiple linear regression or principal component analysis contingent on meta data quality. Through this approach, building energy performance is comprehensively evaluated and optimized. Simultaneously, the significant challenges associated with conventional single-criterion benchmarking models can be avoided. Together with a clustering algorithm on a three-year panel dataset, the benchmarking case of 324 single-family dwellings demonstrated an improved robustness of the presented multi-criteria benchmarking approach over the conventional single-criterion ones

  12. Defense Sector Consolidation: Will Consolidation Within the Defense Sector Improve the Financial Performance of Defense Contractors While, Simultaneously Yielding Cost Savings to Taxpayers

    Science.gov (United States)

    2005-12-01

    Treaty USSR Union of Soviet Socialist Republics WACC Weighted Average Cost of Capital...a present value using the company’s weighted average cost of capital ( WACC ). Synergy: The Premium for Potential Success For the most part

  13. Discharges with surgical procedures performed less often than once per month per hospital account for two-thirds of hospital costs of inpatient surgery.

    Science.gov (United States)

    O'Neill, Liam; Dexter, Franklin; Park, Sae-Hwan; Epstein, Richard H

    2017-09-01

    Most surgical discharges (54%) at the average hospital are for procedures performed no more often than once per month at that hospital. We hypothesized that such uncommon procedures would be associated with an even greater percentage of the total cost of performing all surgical procedures at that hospital. Observational study. State of Texas hospital discharge abstract data: 4th quarter of 2015 and 1st quarter of 2016. Inpatients discharged with a major therapeutic ("operative") procedure. For each of N=343 hospitals, counts of discharges, sums of lengths of stay (LOS), sums of diagnosis related group (DRG) case-mix weights, and sums of charges were obtained for each procedure or combination of procedures, classified by International Classification of Diseases version 10 Procedure Coding System (ICD-10-PCS). Each discharge was classified into 2 categories, uncommon versus not, defined as a procedure performed at most once per month versus those performed more often than once per month. Major procedures performed at most once per month per hospital accounted for an average among hospitals of 68% of the total inpatient costs associated with all major therapeutic procedures. On average, the percentage of total costs associated with uncommon procedures was 26% greater than expected based on their share of total discharges (Pcosts among surgical patients can be attributed to procedures performed at most once per month per hospital. The finding that such uncommon procedures account for a large percentage of costs is important because methods of cost accounting by procedure are generally unsuitable for them. Copyright © 2017 Elsevier Inc. All rights reserved.

  14. Analysis of Cost of Rework on Time and Cost Performance of Building Construction Projects in Abuja, Nigeria

    Directory of Open Access Journals (Sweden)

    Emmanuel Chidiebere Eze

    2018-01-01

    Full Text Available Rework is a menace that leads to undesired and unnecessary loss of efforts, it degrades project cost and schedule performance of construction projects, both at design and construction phases. This study therefore, analyzed the impact of cost of rework on time and cost performance of building construction projects in Nigerian, using selected commercial building project within the country’s capital. A pro forma was adopted for gathering data on rework cost, project cost and time of selected building projects, while structured questionnaire was used to collect information on the likely measures for reducing rework incidences from construction professionals that were involved in the delivery of the identified projects. Regression analysis, relative importance index and Kruskal-Walis test were employed for data analysis. The study revealed a significant relationship between the cost of rework and initial and final project cost of delivering commercial buildings, as an average of 3.53% impact on the initial project cost, 46.60% contribution to cost overrun, and p-value of 0.000 was observed on all assessed projects. For the project delivery time, a significant relationship between the cost of rework and initial and final project duration, as an average of 7.35% impact on the initial delivery time, extra 19 days and p-value of 0.000 was observed on all assessed projects. Team building and education, management commitment, employee involvement, were some of the best possible measures to minimized rework problems.

  15. Learning to assign binary weights to binary descriptor

    Science.gov (United States)

    Huang, Zhoudi; Wei, Zhenzhong; Zhang, Guangjun

    2016-10-01

    Constructing robust binary local feature descriptors are receiving increasing interest due to their binary nature, which can enable fast processing while requiring significantly less memory than their floating-point competitors. To bridge the performance gap between the binary and floating-point descriptors without increasing the computational cost of computing and matching, optimal binary weights are learning to assign to binary descriptor for considering each bit might contribute differently to the distinctiveness and robustness. Technically, a large-scale regularized optimization method is applied to learn float weights for each bit of the binary descriptor. Furthermore, binary approximation for the float weights is performed by utilizing an efficient alternatively greedy strategy, which can significantly improve the discriminative power while preserve fast matching advantage. Extensive experimental results on two challenging datasets (Brown dataset and Oxford dataset) demonstrate the effectiveness and efficiency of the proposed method.

  16. KrF laser cost/performance model for ICF commercial applications

    International Nuclear Information System (INIS)

    Harris, D.B.; Pendergrass, J.H.

    1985-01-01

    Simple expressions suitable for use in commercial-applications plant parameter studies for the direct capital cost plus indirect field costs and for the efficiency as a function of repetition rate were developed for pure-optical-compression KrF laser fusion drivers. These simple expressions summarize estimates obtained from detailed cost-performance studies incorporating recent results of ongoing physics, design, and cost studies. Contributions of KrF laser capital charges and D and M costs to total levelized constant-dollar (1984) unit ICF power generation cost are estimated as a function of plant size and driver pulse energy using a published gain for short-wavelength lasers and representative values of plant parameters

  17. Process-based Cost Estimation for Ramjet/Scramjet Engines

    Science.gov (United States)

    Singh, Brijendra; Torres, Felix; Nesman, Miles; Reynolds, John

    2003-01-01

    Process-based cost estimation plays a key role in effecting cultural change that integrates distributed science, technology and engineering teams to rapidly create innovative and affordable products. Working together, NASA Glenn Research Center and Boeing Canoga Park have developed a methodology of process-based cost estimation bridging the methodologies of high-level parametric models and detailed bottoms-up estimation. The NASA GRC/Boeing CP process-based cost model provides a probabilistic structure of layered cost drivers. High-level inputs characterize mission requirements, system performance, and relevant economic factors. Design alternatives are extracted from a standard, product-specific work breakdown structure to pre-load lower-level cost driver inputs and generate the cost-risk analysis. As product design progresses and matures the lower level more detailed cost drivers can be re-accessed and the projected variation of input values narrowed, thereby generating a progressively more accurate estimate of cost-risk. Incorporated into the process-based cost model are techniques for decision analysis, specifically, the analytic hierarchy process (AHP) and functional utility analysis. Design alternatives may then be evaluated not just on cost-risk, but also user defined performance and schedule criteria. This implementation of full-trade study support contributes significantly to the realization of the integrated development environment. The process-based cost estimation model generates development and manufacturing cost estimates. The development team plans to expand the manufacturing process base from approximately 80 manufacturing processes to over 250 processes. Operation and support cost modeling is also envisioned. Process-based estimation considers the materials, resources, and processes in establishing cost-risk and rather depending on weight as an input, actually estimates weight along with cost and schedule.

  18. Cost optimal levels for energy performance requirements

    DEFF Research Database (Denmark)

    Thomsen, Kirsten Engelund; Aggerholm, Søren; Kluttig-Erhorn, Heike

    This report summarises the work done within the Concerted Action EPBD from December 2010 to April 2011 in order to feed into the European Commission's proposal for a common European procedure for a Cost-Optimal methodology under the Directive on the Energy Performance of Buildings (recast) 2010/3...

  19. Evaluation of Saccharomyces cerevisiae fermentation product as an alternative to monensin on growth performance, cost of gain, and carcass characteristics of heavy-weight yearling beef steers.

    Science.gov (United States)

    Swyers, K L; Wagner, J J; Dorton, K L; Archibeque, S L

    2014-06-01

    Two hundred fifty-two cross-bred yearling steers (406 ± 24 kg BW) were used in a completely randomized block design with a 2 × 2 factorial arrangement of treatments (7 pens/treatment) to evaluate the effects of dietary Saccharomyces cerevisiae fermentation product (SFP) and monensin (MON) on growth performance and carcass characteristics. Dietary treatments arranged as a 2 × 2 factorial were 1) with or without SFP and 2) with or without MON. Finishing diets contained 19.7% of DM as dried distiller's grains with solubles. Both SFP and MON were added in the total mixed ration in place of an equal amount of cornmeal (DM basis; target intake = 2.8 g of SFP and 33 mg of MON/kg of dietary DM). Each treatment group was offered ad libitum access to a transition ration from d 1 to 8 and then to the finishing ration from d 9 to 125. Body weights were collected on d 0, 28, 56, 84, 110, and 125. Initial and final BW was an average of 2-d weights (d -1 and 0 and d 124 and 125, respectively). Steers were shipped for harvest on d 125. Overall ADG was decreased (P = 0.03) in steers supplemented with SFP, but final BW was similar among treatments. Feeding SFP was associated with lighter (P < 0.01) HCW and a greater (P = 0.01) number of carcasses grading USDA Choice. Twelfth rib fat thickness was not affected by SFP (P = 0.82) or MON (P = 0.35), but numerical decreases in 12th rib fat thickness among cattle receiving SFP or MON alone contributed to a tendency (P = 0.07) for greater 12 rib fat thickness when SFP and MON were provided. There was no effect of treatment on cost of gain (P ≥ 0.21). The effects of SFP in the current study may have been limited in heavy yearling steers due to consumption of a finishing diet containing 19.7% dried distiller's grains with solubles.

  20. Stereo Disparity through Cost Aggregation with Guided Filter

    Directory of Open Access Journals (Sweden)

    Pauline Tan

    2014-10-01

    Full Text Available Estimating the depth, or equivalently the disparity, of a stereo scene is a challenging problem in computer vision. The method proposed by Rhemann et al. in 2011 is based on a filtering of the cost volume, which gives for each pixel and for each hypothesized disparity a cost derived from pixel-by-pixel comparison. The filtering is performed by the guided filter proposed by He et al. in 2010. It computes a weighted local average of the costs. The weights are such that similar pixels tend to have similar costs. Eventually, a winner-take-all strategy selects the disparity with the minimal cost for each pixel. Non-consistent labels according to left-right consistency are rejected; a densification step can then be launched to fill the disparity map. The method can be used to solve other labeling problems (optical flow, segmentation but this article focuses on the stereo matching problem.

  1. A longitudinal study of childhood obesity, weight status change, and subsequent academic performance in Taiwanese children.

    Science.gov (United States)

    Chen, Li-Jung; Fox, Kenneth R; Ku, Po-Wen; Wang, Ching-Hui

    2012-09-01

    This study examined the association among childhood obesity, weight status change, and subsequent academic performance at 6-year follow-up. First-grade students from one elementary school district in Taichung City, Taiwan were followed for 6 years (N = 409). Academic performance was extracted from the school records at the end of each grade. Weight and height were measured at the beginning of each grade. A weight change variable was created based on each child's weight status difference at grades 1 and 6. A multivariate linear regression model for predicting academic performance at grade 6 was developed with adjustment for individual characteristics and family factors. A latent growth curve (LGC) showed the association between changes in body mass index (BMI) and in academic performance across a 6-year period. BMI in children increased significantly across 6 years. The rate of increase in BMI over 6 years was higher for children with higher baseline BMIs than it was for children with lower baseline BMIs. However, BMI changes were not significantly associated with changes of academic performance. There was no significant relationship between initial obesity or change in weight status and subsequent academic performance. It appears that either being or becoming overweight/obese did not impact academic achievement for these Taiwanese children. © 2012, American School Health Association.

  2. [Financing, organization, costs and services performance of the Argentinean health sub-systems.

    Science.gov (United States)

    Yavich, Natalia; Báscolo, Ernesto Pablo; Haggerty, Jeannie

    2016-01-01

    To analyze the relationship between health system financing and services organization models with costs and health services performance in each of Rosario's health sub-systems. The financing and organization models were characterized using secondary data. Costs were calculated using the WHO/SHA methodology. Healthcare quality was measured by a household survey (n=822). Public subsystem:Vertically integrated funding and primary healthcare as a leading strategy to provide services produced low costs and individual-oriented healthcare but with weak accessibility conditions and comprehensiveness. Private subsystem: Contractual integration and weak regulatory and coordination mechanisms produced effects opposed to those of the public sub-system. Social security: Contractual integration and strong regulatory and coordination mechanisms contributed to intermediate costs and overall high performance. Each subsystem financing and services organization model had a strong and heterogeneous influence on costs and health services performance.

  3. Cost optimization of load carrying thin-walled precast high performance concrete sandwich panels

    DEFF Research Database (Denmark)

    Hodicky, Kamil; Hansen, Sanne; Hulin, Thomas

    2015-01-01

    and HPCSP’s geometrical parameters as well as on material cost function in the HPCSP design. Cost functions are presented for High Performance Concrete (HPC), insulation layer, reinforcement and include labour-related costs. The present study reports the economic data corresponding to specific manufacturing......The paper describes a procedure to find the structurally and thermally efficient design of load-carrying thin-walled precast High Performance Concrete Sandwich Panels (HPCSP) with an optimal economical solution. A systematic optimization approach is based on the selection of material’s performances....... The solution of the optimization problem is performed in the computer package software Matlab® with SQPlab package and integrates the processes of HPCSP design, quantity take-off and cost estimation. The proposed optimization process outcomes in complex HPCSP design proposals to achieve minimum cost of HPCSP....

  4. Performance indicators, practices and maintenance costs in tires management of a transport company

    Directory of Open Access Journals (Sweden)

    Marcos Dario

    2014-12-01

    Full Text Available There are three operational costs that are more expressive for PSL: vehicle maintenance, tires and fuel. In studies of maintenance has been little researched the concept of tire management, technical maintenance and performance together. In this context, this study aims at identifying the practices and performance indicators in the area of maintenance and tire management also analyze the influence of costs applied to the tires on the total cost of maintenance. We conducted a case study of exploratory and descriptive. The main instruments of data collection were on-site observation, unstructured interviews, document analysis and reports results indicators. Data were analyzed by correlation analysis and multiple regression. It was revealed that among the performance indicators in the management of tire maintenance costs applied to the tires have a higher correlation with the total cost of maintenance. The ANOVA indicated that tire maintenance costs influence in 54% of the variations in the total cost of maintenance. We clarified the concepts of maintenance techniques specific tire management, and identify performance indicators in the area of tire managent.

  5. Reliable, Low-Cost, Low-Weight, Non-Hermetic Coating for MCM Applications

    Science.gov (United States)

    Jones, Eric W.; Licari, James J.

    2000-01-01

    Through an Air Force Research Laboratory sponsored STM program, reliable, low-cost, low-weight, non-hermetic coatings for multi-chip-module(MCK applications were developed. Using the combination of Sandia Laboratory ATC-01 test chips, AvanTeco's moisture sensor chips(MSC's), and silicon slices, we have shown that organic and organic/inorganic overcoatings are reliable and practical non-hermetic moisture and oxidation barriers. The use of the MSC and unpassivated ATC-01 test chips provided rapid test results and comparison of moisture barrier quality of the overcoatings. The organic coatings studied were Parylene and Cyclotene. The inorganic coatings were Al2O3 and SiO2. The choice of coating(s) is dependent on the environment that the device(s) will be exposed to. We have defined four(4) classes of environments: Class I(moderate temperature/moderate humidity). Class H(high temperature/moderate humidity). Class III(moderate temperature/high humidity). Class IV(high temperature/high humidity). By subjecting the components to adhesion, FTIR, temperature-humidity(TH), pressure cooker(PCT), and electrical tests, we have determined that it is possible to reduce failures 50-70% for organic/inorganic coated components compared to organic coated components. All materials and equipment used are readily available commercially or are standard in most semiconductor fabrication lines. It is estimated that production cost for the developed technology would range from $1-10/module, compared to $20-200 for hermetically sealed packages.

  6. The energy cost of playing active video games in children with obesity and children of a healthy weight.

    Science.gov (United States)

    O'Donovan, C; Roche, E F; Hussey, J

    2014-08-01

    Increasing physical activity and reducing sedentary behaviour form a large part of the treatment of paediatric obesity. However, many children today spend prolonged periods of time playing sedentary video games. Active video games (AVGs) represent a novel and child friendly form of physical activity. To measure the energy cost of playing two AVGs in children with obesity and healthy age- and gender-matched children. The energy cost of gaming and heart rates achieved during gaming conditions were compared between groups. AVG play can result in light-to-moderate intensity physical activity (2.7-5.4 metabolic equivalents). When corrected for fat-free mass those with obesity expended significantly less energy than healthy weight peers playing Nintendo Wii Fit Free Jogging (P = 0.017). No significant difference was seen between groups in the energy cost of playing Boxing. Certain AVGs, particularly those that require lower limb movement, could be used to increase total energy expenditure, replace more sedentary activities, or achieve moderate intensity physical activity among children with obesity. There seems to be some differences in how children with obesity and children of a healthy weight play AVGs. This could result in those with obesity expending less energy than their lean peers during AVG play. © 2013 The Authors. Pediatric Obesity © 2013 International Association for the Study of Obesity.

  7. Recruitment of young adults into a randomized controlled trial of weight gain prevention: message development, methods, and cost.

    Science.gov (United States)

    Tate, Deborah F; LaRose, Jessica G; Griffin, Leah P; Erickson, Karen E; Robichaud, Erica F; Perdue, Letitia; Espeland, Mark A; Wing, Rena R

    2014-08-16

    Young adulthood (age 18 to 35) is a high-risk period for unhealthy weight gain. Few studies have recruited for prevention of weight gain, particularly in young adults. This paper describes the recruitment protocol used in the Study of Novel Approaches to Prevention (SNAP). We conducted extensive formative work to inform recruitment methods and message development. We worked with a professional marketing firm to synthesize major themes and subsequently develop age-appropriate messages for recruitment. A variety of approaches and channels were used across two clinical centers to recruit young adults who were normal or overweight (body mass index (BMI) 21 to 30 kg/m2) for a 3-year intervention designed to prevent weight gain. We tracked recruitment methods, yields, and costs by method. Logistic regression was used to identify recruitment methods that had the highest relative yield for subgroups of interest with covariate adjustments for clinic. The final sample of 599 participants (27% minority, 22% male) was recruited over a 19-month period of sustained efforts. About 10% of those who initially expressed interest via a screening website were randomized. The most common reason for ineligibility was already being obese (BMI >30 kg/m2). The top two methods for recruitment were mass mailing followed by email; together they were cited by 62% of those recruited. Television, radio, paid print advertising, flyers and community events each yielded fewer than 10% of study participants. Email was the most cost-effective method per study participant recruited. These findings can guide future efforts to recruit young adults and for trials targeting weight gain prevention. ClinicalTrials.gov NCT01183689 (registered 13 August 2010).

  8. A simple idea for reducing the cost and weight of plaster-cast orthoses Uma ideia simples para diminuir custo e peso das talas gessadas

    Directory of Open Access Journals (Sweden)

    André Esmanhotto

    2013-01-01

    Full Text Available OBJECTIVE: To reduce the cost and weight of plaster molded orthosis (increasing patient comfort, keeping the same resistance. METHODS: 22 plaster orthosis were analysed, 11 with conventional shape and 11 with pyramidal shape. It was compared, in theory (mathematcally and practice, the change of weight (and consequently cost and flexion resistance between conventional shape and pyramidal shape. RESULTS: Theorical analysis: weight and cost decrease of 26.7%-38.9%, according to the layers disposition of the cast. Laboratorial analysis: cast´s weight decrease of 34.5% (p = 0.000005 and resistance increase of 26.7% (p = 0.03. CONCLUSION: plaster molded orthosis made in a pyramidal shape, have a statistically significant decrease of weight (and consequently cost and statistically significant increase of resistance if compared with traditional shape. OBJETIVO: Diminuir o custo e o peso (aumentando o conforto para o paciente das talas gessadas, mantendo resistência semelhante. MÉTODOS: Foram analisadas 22 talas de gesso, 11 com formato convencional e 11 com formato piramidal. Foi feita comparação, teórica (matemática e prática, entre as talas convencionais e as piramidais quanto à mudança de peso (e consequentemente de custo e à resistência à flexão. RESULTADOS: Análise matemática – diminuição peso e custo entre 26,7% e 38,9%, variando conforme a disposição das camadas da tala. Análise prática – diminuição do peso em 34,5% (p = 0,000005 e resistência aumentada em 26,7% (p = 0,03. CONCLUSÃO: A tala gessada com formato piramidal apresenta diminuição estatisticamente significativa de peso (e consequentemente de custo, com aumento estatisticamente significativo da resistência, se comparada à tala de formato convencional.

  9. EFFECT OF COST INCREMENT DISTRIBUTION PATTERNS ON THE PERFORMANCE OF JIT SUPPLY CHAIN

    Directory of Open Access Journals (Sweden)

    Ayu Bidiawati J.R

    2008-01-01

    Full Text Available Cost is an important consideration in supply chain (SC optimisation. This is due to emphasis placed on cost reduction in order to optimise profit. Some researchers use cost as one of their performance measures and others propose ways of accurately calculating cost. As product moves across SC, the product cost also increases. This paper studied the effect of cost increment distribution patterns on the performance of a JIT Supply Chain. In particular, it is necessary to know if inventory allocation across SC needs to be modified to accommodate different cost increment distribution patterns. It was found that funnel is still the best card distribution pattern for JIT-SC regardless the cost increment distribution patterns used.

  10. Cost optimal building performance requirements. Calculation methodology for reporting on national energy performance requirements on the basis of cost optimality within the framework of the EPBD

    Energy Technology Data Exchange (ETDEWEB)

    Boermans, T.; Bettgenhaeuser, K.; Hermelink, A.; Schimschar, S. [Ecofys, Utrecht (Netherlands)

    2011-05-15

    On the European level, the principles for the requirements for the energy performance of buildings are set by the Energy Performance of Buildings Directive (EPBD). Dating from December 2002, the EPBD has set a common framework from which the individual Member States in the EU developed or adapted their individual national regulations. The EPBD in 2008 and 2009 underwent a recast procedure, with final political agreement having been reached in November 2009. The new Directive was then formally adopted on May 19, 2010. Among other clarifications and new provisions, the EPBD recast introduces a benchmarking mechanism for national energy performance requirements for the purpose of determining cost-optimal levels to be used by Member States for comparing and setting these requirements. The previous EPBD set out a general framework to assess the energy performance of buildings and required Member States to define maximum values for energy delivered to meet the energy demand associated with the standardised use of the building. However it did not contain requirements or guidance related to the ambition level of such requirements. As a consequence, building regulations in the various Member States have been developed by the use of different approaches (influenced by different building traditions, political processes and individual market conditions) and resulted in different ambition levels where in many cases cost optimality principles could justify higher ambitions. The EPBD recast now requests that Member States shall ensure that minimum energy performance requirements for buildings are set 'with a view to achieving cost-optimal levels'. The cost optimum level shall be calculated in accordance with a comparative methodology. The objective of this report is to contribute to the ongoing discussion in Europe around the details of such a methodology by describing possible details on how to calculate cost optimal levels and pointing towards important factors and

  11. Assessing the Costs and Benefits of the Superior Energy Performance Program

    Energy Technology Data Exchange (ETDEWEB)

    Therkelsen, Peter; McKane, Aimee; Sabouini, Ridah; Evans, Tracy

    2013-07-01

    Industrial companies are seeking to manage energy consumption and costs, mitigate risks associated with energy, and introduce transparency into reports of their energy performance achievements. Forty industrial facilities are participating in the U.S. DOE supported Superior Energy Performance (SEP) program in which facilities implement an energy management system based on the ISO 50001 standard, and pursue third-party verification of their energy performance improvements. SEP certification provides industrial facilities recognition for implementing a consistent, rigorous, internationally recognized business process for continually improving energy performance and achievement of established energy performance improvement targets. This paper focuses on the business value of SEP and ISO 50001, providing an assessment of the costs and benefits associated with SEP implementation at nine SEP-certified facilities across a variety of industrial sectors. These cost-benefit analyses are part of the U.S. DOE?s contribution to the Global Superior Energy Performance (GSEP) partnership, a multi-country effort to demonstrate, using facility data, that energy management system implementation enables companies to improve their energy performance with a greater return on investment than business-as-usual (BAU) activity. To examine the business value of SEP certification, interviews were conducted with SEP-certified facilities. The costs of implementing the SEP program, including internal facility staff time, are described and a marginal payback of SEP certification has been determined. Additionally, more qualitative factors with regard to the business value and challenges related to SEP and ISO 50001 implementation are summarized.

  12. Re-Engineering a High Performance Electrical Series Elastic Actuator for Low-Cost Industrial Applications

    Directory of Open Access Journals (Sweden)

    Kenan Isik

    2017-01-01

    Full Text Available Cost is an important consideration when transferring a technology from research to industrial and educational use. In this paper, we introduce the design of an industrial grade series elastic actuator (SEA performed via re-engineering a research grade version of it. Cost-constrained design requires careful consideration of the key performance parameters for an optimal performance-to-cost component selection. To optimize the performance of the new design, we started by matching the capabilities of a high-performance SEA while cutting down its production cost significantly. Our posit was that performing a re-engineering design process on an existing high-end device will significantly reduce the cost without compromising the performance drastically. As a case study of design for manufacturability, we selected the University of Texas Series Elastic Actuator (UT-SEA, a high-performance SEA, for its high power density, compact design, high efficiency and high speed properties. We partnered with an industrial corporation in China to research the best pricing options and to exploit the retail and production facilities provided by the Shenzhen region. We succeeded in producing a low-cost industrial grade actuator at one-third of the cost of the original device by re-engineering the UT-SEA with commercial off-the-shelf components and reducing the number of custom-made parts. Subsequently, we conducted performance tests to demonstrate that the re-engineered product achieves the same high-performance specifications found in the original device. With this paper, we aim to raise awareness in the robotics community on the possibility of low-cost realization of low-volume, high performance, industrial grade research and education hardware.

  13. APPLICATION, PERFORMANCE, AND COSTS OF ...

    Science.gov (United States)

    A critical review of biological treatment processes for remediation of contaminated soils is presented. The focus of the review is on documented cost and performance of biological treatment technologies demonstrated at full- or field-scale. Some of the data were generated by the U.S. Environmental Protection Agency's (EPA's) Bioremediation in the Field Program, jointly supported by EPA's Office of Research and Development, EPA's Office of Solid Waste and Emergency Waste, and the EPA Regions through the Superfund Innovative Technology Evaluation Program (SITE) Program. Military sites proved to be another fertile data source. Technologies reviewed in this report include both ex-situ processes, (land treatment, biopile/biocell treatment, composting, and bioslurry reactor treatment) and in-situ alternatives (conventional bioventing, enhanced or cometabolic bioventing, anaerobic bioventing, bioslurping, phytoremediation, and natural attenuation). Targeted soil contaminants at the documented sites were primarily organic chemicals, including BTEX, petroleum hydrocarbons, polycyclic aromatic hydrocarbons (PAHs), chlorinated aliphatic hydrocarbons (CAHs), organic solvents, polychlorinated biphenyls (PCBs), pesticides, dioxin, and energetics. The advantages, limitations, and major cost drivers for each technology are discussed. Box and whisker plots are used to summarize before and after concentrations of important contaminant groups for those technologies consider

  14. Can community-based, low-cost antenatal care in the third trimester of pregnancy reduce the incidence of low birth weight newborns?

    Science.gov (United States)

    Chaudhary, A K; Chaudhary, Asha; Tiwari, S C; Dwivedi, R

    2012-06-01

    To determine if community-based, low-cost interventions during third trimester of pregnancy can reduce the incidence of low birth weight babies. In a case control study, 290 pregnant women from a slum area were registered in the beginning of third trimester of pregnancy and provided full antenatal care comprising fortnightly check up, one IFA tablet daily, counseling for minimum one-and-a-half hour post-lunch rest in left lateral position, additional diet to ensure minimum 2,200 kcal per day, and management of clinical conditions, if any. An equal number of pregnant women belonging to the same slum area were registered as control who received routine antenatal services from the existing health care facilities. The birth weight of the babies in the two groups were recorded and compared. Test of significance and correlation coefficient were applied to the data. Mean birth weight of the babies of the Subjects was 2.76 kg (SD 0.39) compared to mean birth weight of 2.57 kg (SD 0.36) of the babies in the Control group. Incidence of low birth weight babies among subjects who consumed minimum 2,400 kcal per day, had one-and-a-half hour post-lunch rest in left lateral position and who consumed one tablet of IFA (100 mg iron and 5 mg folic acid) per day during the last trimester of pregnancy was lower (17.6 %) as compared with women in the Control group (36.2 %). The difference in the mean birth weight of newborns of the two groups was statistically significant (t = 2.52, p < 0.01). Incidence of low birth weight babies can be significantly reduced by providing simple, low-cost care to pregnant women during the last trimester of pregnancy in the community setting.

  15. FACTORS AFFECTING COST PERFORMANCE IN CONSTRUCTION PROJECTS WITHIN KELANTAN STATE IN MALAYSIA

    OpenAIRE

    ABDELNASER OMRAN; SITI NORHYDAYATON BINTI MAMAT

    2011-01-01

    This study investigates the factors affecting cost performance of construction projects in Kelantan State located in the east-coast part of Malaysia. It draws on relevant previous research in the theory of work on cost performance. Thirty-three contractors companies with different working grades in the state of Kelantan were participated in the study. Data were collected from the contractors using a questionnaire survey. The results indicated that the success factors affecting the cost perfor...

  16. Depressive symptoms and poorer performance on the Stroop Task are associated with weight gain.

    Science.gov (United States)

    Stinson, Emma J; Krakoff, Jonathan; Gluck, Marci E

    2018-03-15

    Executive function impairments and depression are associated with obesity but whether they predict weight gain is unclear. Forty-six individuals (35m, 37±10y) completed the Stroop Task, Iowa Gambling Task (IGT), Wisconsin Card Sorting Task (WCST), Inventory for Depressive Symptomatology (IDS-SR), Physical Anhedonia Scale (PAS), and Perceived Stress Scale (PSS). Body composition (DXA) and fasting glucose were also measured. Data from return visits were used to assess changes in weight. Poorer Stroop and WCST performance associated with higher BMI whereas poorer IGT and WCST performance associated with higher body fat (%; all p's≤0.05). Stroop interference (p=0.04; p=0.05) and IDS-SR (p=0.06; p=0.02) associated with increased BMI and weight gain (%/yr). In a multivariate linear model Stroop interference (β=0.40, p<0.01; β=0.35, p<0.01) and IDS-SR (β=0.38, p<0.01; β=0.37, p<0.01) independently predicted increased BMI and weight gain (%/yr) even after controlling for baseline weight and glucose levels. Poorer response inhibition and depressive symptoms, but not glucose levels, predicted weight gain. Evaluating neurocognitive and mood deficits could improve current treatment strategies for weight loss. Clinical Trial Registration Numbers NCT00523627, NCT00342732, NCT01224704. clinicaltrials.gov. Published by Elsevier Inc.

  17. Analysis on Occupants’ Satisfaction for Safety Performance Assessment in Low Cost Housing

    Directory of Open Access Journals (Sweden)

    Husin Husrul Nizam

    2014-01-01

    Full Text Available The delivery performance of the low cost housing is questioned since the occupants are prone towards safety hazards in the housing complex, such as structural instability and falling building fragments. Without defining the occupants’ requirements for the development of low cost housing, the prevailing safety factors are hard to be determined. This paper explores the rationale of safety performance assessment in the low cost housing by considering the occupants’ participation to achieve a better safety provision during occupancy period. Questionnaire survey was distributed to 380 occupants of the low cost housing in Kuala Lumpur and Selangor, Malaysia. The result shows that 80.8% of the respondents had expressed their dissatisfaction with the safety performance of the lift. By referring to the mode of ranking level, the most significant aspect rated by the respondents is Building Safety Features, with 51.6% respondents. The attained aspects can be fundamental parameters which can be considered in the future development of low cost housing.

  18. Studies in Software Cost Model Behavior: Do We Really Understand Cost Model Performance?

    Science.gov (United States)

    Lum, Karen; Hihn, Jairus; Menzies, Tim

    2006-01-01

    While there exists extensive literature on software cost estimation techniques, industry practice continues to rely upon standard regression-based algorithms. These software effort models are typically calibrated or tuned to local conditions using local data. This paper cautions that current approaches to model calibration often produce sub-optimal models because of the large variance problem inherent in cost data and by including far more effort multipliers than the data supports. Building optimal models requires that a wider range of models be considered while correctly calibrating these models requires rejection rules that prune variables and records and use multiple criteria for evaluating model performance. The main contribution of this paper is to document a standard method that integrates formal model identification, estimation, and validation. It also documents what we call the large variance problem that is a leading cause of cost model brittleness or instability.

  19. Reducing rotor weight

    Energy Technology Data Exchange (ETDEWEB)

    Cheney, M.C. [PS Enterprises, Inc., Glastonbury, CT (United States)

    1997-12-31

    The cost of energy for renewables has gained greater significance in recent years due to the drop in price in some competing energy sources, particularly natural gas. In pursuit of lower manufacturing costs for wind turbine systems, work was conducted to explore an innovative rotor designed to reduce weight and cost over conventional rotor systems. Trade-off studies were conducted to measure the influence of number of blades, stiffness, and manufacturing method on COE. The study showed that increasing number of blades at constant solidity significantly reduced rotor weight and that manufacturing the blades using pultrusion technology produced the lowest cost per pound. Under contracts with the National Renewable Energy Laboratory and the California Energy Commission, a 400 kW (33m diameter) turbine was designed employing this technology. The project included tests of an 80 kW (15.5m diameter) dynamically scaled rotor which demonstrated the viability of the design.

  20. PERFORMANCE EVALUATION OF A LIGHT-WEIGHT MULTI-ECHO LIDAR FOR UNMANNED ROTORCRAFT APPLICATIONS

    Directory of Open Access Journals (Sweden)

    G. Conte

    2013-08-01

    Full Text Available The paper presents a light-weight and low-cost airborne terrain mapping system. The developed Airborne LiDAR Scanner (ALS system consists of a high-precision GNSS receiver, an inertial measurement unit and a magnetic compass which are used to complement a LiDAR sensor in order to compute a digital surface model. Evaluation of the accuracy of the generated surface model is presented. Additionally, a comparison is provided between the surface model generated from the developed ALS system and a model generated using a commercial photogrammetric software. Finally, the multi-echo capability of the used LiDAR sensor is evaluated in areas covered with dense vegetation. The ALS system and camera systems were mounted on-board an industrial unmanned helicopter of around 100 kilograms maximum take-off weight. Presented results are based on real flight-test data.

  1. Effects of weight training on power performance

    Directory of Open Access Journals (Sweden)

    KAUKAB AZEEM

    2011-06-01

    Full Text Available Introduction: Harris et al. declared that some researchers claim the use of 80% of 1RM is recommended toimprove power characteristics, while others suggest 50-60% of 1RM and below. Kawamori and Haff agreed withHarris et al., stating that there is inconsistency in the optimal load to produce the highest power. They claimedthat some studies that used untrained subjects, single joint exercises, and upper-body exercises reported 30-45%of 1RM, while others using trained subjects, multi-joint exercises, and lower-body exercises reported 30-70% of1RM.Method: The purpose of the study was to find out the effect of weight training in the developing the powerperformance among 20 students between 16 to 18 years of age enrolled for physical education course for theacademic year 2010, were selected as subjects. Pre and post test was conducted for the group on 1RM of squats,bench press and dead lift. 45 minutes weight training program, twice a week, for 12 weeks was given to thesubjects. The statistical tools used were mean, SD, and ‘t’ –test.Results & Discussion: The analysis of the data reveals that the subjects with the training have shownimprovement in the performance of squats from pre to post test with the mean and S.D being (76.00, 26.59 and(93.75, 27.19 respectively. The improvement is quite encouraging and highly significant (p<0.0001.With regard to bench press exercise of the subjects the mean and S.D in the pre and post test were (53.00, 23.14and (70.25, 23.37. The data clearly speaks of an improved performance from pre to post scores of the studentswhich is highly significant at (p<0.0001. The mean and S.D in the pre and post test were (104.00, 28.31 and(135.00, 24.97 respectively with respect to dead lift exercise. There is an increase in the power of the studentswhich is encouraging and highly significant with (p<0.0001.Conclusions: It is concluded from this study, that there was a marked improvement in the performance of thestudents in

  2. Cost of nursing most frequent procedures performed on severely burned patients

    Directory of Open Access Journals (Sweden)

    Talita de Oliveira Melo

    Full Text Available ABSTRACT Objective: to identify the mean direct cost (MDC of the most frequent procedures performed by nursing professionals on severely burned patients in an Intensive Care Unit. Method: exploratory-descriptive quantitative single-case study. The MDC was calculated by multiplying time (timed spent by nursing professionals in the performance of the procedures by the unit cost of direct labor, and adding the costs of material and medicine/solutions. Results: a MDC of US$ 0.65 (SD=0.36 was obtained for "vital signs monitoring"; US$ 10.00 (SD=24.23 for "intravenous drug administration"; US$ 5.90 (SD=2.75 for "measurement of diuresis"; US$ 0.93 (SD=0.42 for "capillary blood glucose monitoring"; and US$ 99.75 (SD=129.55 for "bandaging". Conclusion: the knowledge developed can support managerial decision-making, contribute to the efficiency distribution of the resources involved and, when possible, provide cost-containment or cost-minimization strategies without impairing the quality of nursing care.

  3. Fuel ethanol from cane molasses in Thailand: Environmental and cost performance

    International Nuclear Information System (INIS)

    Nguyen, Thu Lan T.; Gheewala, Shabbir H.

    2008-01-01

    In the context of the world's energy crisis and environmental concerns, crop-based ethanol has emerged as an energy alternative, the use of which can help reduce oil imports as well as emissions of CO 2 and other air pollutants. However, a clear disadvantage of ethanol is its high cost over gasoline under the current pricing scheme that does not include externalities. The intent of this study is to perform a life cycle analysis comparing environmental and cost performance of molasses-based E10 with those of CG. The results show that although E10 provides reduction in fossil energy use, petroleum use, CO 2 and NO x emissions, its total social costs are higher than those of gasoline due to higher direct production costs and external costs for other air emissions, e.g. CH 4 , N 2 O, CO, SO 2 , VOC and PM 10 . An analysis of projection scenarios shows that technological innovations towards cleaner production help maximize ethanol's benefits whilst minimizing its limitations

  4. Development of low-cost high-performance multispectral camera system at Banpil

    Science.gov (United States)

    Oduor, Patrick; Mizuno, Genki; Olah, Robert; Dutta, Achyut K.

    2014-05-01

    Banpil Photonics (Banpil) has developed a low-cost high-performance multispectral camera system for Visible to Short- Wave Infrared (VIS-SWIR) imaging for the most demanding high-sensitivity and high-speed military, commercial and industrial applications. The 640x512 pixel InGaAs uncooled camera system is designed to provide a compact, smallform factor to within a cubic inch, high sensitivity needing less than 100 electrons, high dynamic range exceeding 190 dB, high-frame rates greater than 1000 frames per second (FPS) at full resolution, and low power consumption below 1W. This is practically all the feature benefits highly desirable in military imaging applications to expand deployment to every warfighter, while also maintaining a low-cost structure demanded for scaling into commercial markets. This paper describes Banpil's development of the camera system including the features of the image sensor with an innovation integrating advanced digital electronics functionality, which has made the confluence of high-performance capabilities on the same imaging platform practical at low cost. It discusses the strategies employed including innovations of the key components (e.g. focal plane array (FPA) and Read-Out Integrated Circuitry (ROIC)) within our control while maintaining a fabless model, and strategic collaboration with partners to attain additional cost reductions on optics, electronics, and packaging. We highlight the challenges and potential opportunities for further cost reductions to achieve a goal of a sub-$1000 uncooled high-performance camera system. Finally, a brief overview of emerging military, commercial and industrial applications that will benefit from this high performance imaging system and their forecast cost structure is presented.

  5. Direct health care costs associated with obesity in Chinese population in 2011.

    Science.gov (United States)

    Shi, Jingcheng; Wang, Yao; Cheng, Wenwei; Shao, Hui; Shi, Lizheng

    2017-03-01

    Overweight and obesity are established major risk factors for type 2 diabetes, and major public health concerns in China. This study aims to assess the economic burden associated with overweight and obesity in the Chinese population ages 45 and older. The Chinese Health and Retirement Longitudinal Study (CHARLS) in 2011 included 13,323 respondents of ages 45 and older living in 450 rural and urban communities across China. Demographic information, height, weight, direct health care costs for outpatient visits, hospitalization, and medications for self-care were extracted from the CHARLS database. Health Care costs were calculated in 2011 Chinese currency. The body mass index (BMI) was used to categorize underweight, normal weight, overweight, and obese populations. Descriptive analyses and a two-part regression model were performed to investigate the association of BMI with health care costs. To account for non-normality of the cost data, we applied a non-parametric bootstrap approach using the percentile method to estimate the 95% confidence intervals (95% CIs). Overweight and obese groups had significantly higher total direct health care costs (RMB 2246.4, RMB 2050.7, respectively) as compared with the normal-weight group (RMB 1886.0). When controlling for demographic characteristics, overweight and obese adults were 15.0% and 35.9% more likely to incur total health care costs, and obese individuals had 14.2% higher total health care costs compared with the normal-weight group. Compared with the normal-weight counterparts, the annual total direct health care costs were significantly higher among obese adults in China. Copyright © 2016 Elsevier Inc. All rights reserved.

  6. New MEA Materials for Improved DMFC Performance, Durability and Cost

    Energy Technology Data Exchange (ETDEWEB)

    Fletcher, James H. [University of North Florida; Campbell, Joseph L. [University of North Florida; Cox, Philip [University of North Florida; Harrington, William J. [University of North Florida

    2013-09-16

    Abstract Project Title: New MEA Materials for Improved DMFC Performance, Durability and Cost The University of North Florida (UNF)--with project partners the University of Florida, Northeastern University, and Johnson Matthey--has recently completed the Department of Energy (DOE) project entitled “New MEA Materials for Improved DMFC Performance, Durability and Cost”. The primary objective of the project was to advance portable fuel cell MEA technology towards the commercial targets as laid out in the DOE R&D roadmap by developing a passive water recovery MEA (membrane electrode assembly). Developers at the University of North Florida identified water management components as an insurmountable barrier to achieving the required system size and weight necessary to achieve the energy density requirements of small portable power applications. UNF developed an innovative “passive water recovery” MEA for direct methanol fuel cells (DMFC) which provides a path to system simplification and optimization. The passive water recovery MEA incorporates a hydrophobic, porous, barrier layer within the cathode electrode, so that capillary pressure forces the water produced at the cathode through holes in the membrane and back to the anode. By directly transferring the water from the cathode to the anode, the balance of plant is very much simplified and the need for heavy, bulky water recovery components is eliminated. At the heart of the passive water recovery MEA is the UNF DM-1 membrane that utilizes a hydrocarbon structure to optimize performance in a DMFC system. The membrane has inherent performance advantages, such as a low methanol crossover (high overall efficiency), while maintaining a high proton conductivity (good electrochemical efficiency) when compared to perfluorinated sulfonic acid membranes such as Nafion. Critically, the membrane provides an extremely low electro-osmotic drag coefficient of approximately one water molecule per proton (versus the 2-3 for

  7. Understanding product cost vs. performance through an in-depth system Monte Carlo analysis

    Science.gov (United States)

    Sanson, Mark C.

    2017-08-01

    The manner in which an optical system is toleranced and compensated greatly affects the cost to build it. By having a detailed understanding of different tolerance and compensation methods, the end user can decide on the balance of cost and performance. A detailed phased approach Monte Carlo analysis can be used to demonstrate the tradeoffs between cost and performance. In complex high performance optical systems, performance is fine-tuned by making adjustments to the optical systems after they are initially built. This process enables the overall best system performance, without the need for fabricating components to stringent tolerance levels that often can be outside of a fabricator's manufacturing capabilities. A good performance simulation of as built performance can interrogate different steps of the fabrication and build process. Such a simulation may aid the evaluation of whether the measured parameters are within the acceptable range of system performance at that stage of the build process. Finding errors before an optical system progresses further into the build process saves both time and money. Having the appropriate tolerances and compensation strategy tied to a specific performance level will optimize the overall product cost.

  8. Quantification of intestinal bacteria, operating cost and performance of fingerlings Nile tilapia subjected to probiotics

    Directory of Open Access Journals (Sweden)

    Nilton Garcia-Marengoni

    2015-05-01

    Full Text Available The use of microorganisms of the genus Bacillus in aquaculture is a nutritional management practice that is rapidly expanding in regions with intensive fish farming. This study aimed to quantify the total bacteria and total coliforms from the intestinal microbiota and estimate the partial operating costs and growth performance of Nile tilapia (Oreochromis niloticus of the GIFT strain. A total of 1,200 post-larvae (24.7 ± 0.50 mg were distributed into 24 aquaria (0.03-m³ capacity within a completely randomized design in 2 x 3 factorial (phase x bacteria, with four replications. Each aquarium, containing 50 post-larvae (sex reversal phase or 30 fish (fingerlings phase, it was considered to be an experimental unit, consisting of three treatments (diet+Bacillus subtilis C-3102, diet+Bacillus cereus var. toyoi and diet without probiotic addition. The quantification of the total bacteria and total coliforms of the intestinal microbiota of tilapia were influenced (P 0.05 by adding probiotics in the diets and no effect of the interaction between phase and bacteria was observed. The weight gain, average daily weight gain, specific growth rate and apparent feed conversion were not affected (P > 0.05 by inclusion of probiotics as part of the diets. The inclusion of B. subtilis and B. cereus as part of diets for Nile tilapia promotes intestinal colonization and improves the survival rate without negatively influencing the feed intake, total biomass, gross revenue and partial operating costs and net revenue. Therefore it recommends the use of these probiotics to growth of tilapia fingerlings Nile, GIFT strain.

  9. Identifying and weighting of key performance indicators of knowledge management2.0 in organizations

    Directory of Open Access Journals (Sweden)

    Saeed Khalilazar

    2016-03-01

    Full Text Available Main purpose of this research is identifying and weighting of key performance indicators of knowledge management2.0 in organizations. According to widespread permeation of technology, especially social media in different organizational dimensions and functional view to this phenomenon in knowledge management, performance measurement of this kind of media in order to meet organizational goals seems necessary. KM2.0 key performance indicators in this article has been identified and weighted through Delphi methodology, via questionnaire in three rounds. KM2.0 KPIs which are identified and weighted in this article are applicable in organizations that are eager to implement KM2.0 initiative and they can measure the performance of KM2.0 activities therefore this research is applicable in goal oriented approach. According to the results, KM2.0 participation process consists of 3 stages and 8 steps as mentioned below: First stage which is presence, consists of 3 steps which are registration, visit and download. Second stage which is feedback consists of 3 steps which are conversation, applause and amplification. Finally, third stage which is creation consists of 2 steps which are codification and personalization. Ultimate contribution of this research is identifying and weighting KPIs of KM2.0 in conceptual framework of KM2.0. Based on developing a conceptual framework and participation process in KM2.0 and listing related KPIs as an applicable solution in order to measure and improve the performance of organizational social media, this research has unique innovation among related and other articles.

  10. The Effects of Differential Goal Weights on the Performance of a Complex Financial Task.

    Science.gov (United States)

    Edmister, Robert O.; Locke, Edwin A.

    1987-01-01

    Determined whether people could obtain outcomes on a complex task that would be in line with differential goal weights corresponding to different aspects of the task. Bank lending officers were run through lender-simulation exercises. Five performance goals were weighted. Demonstrated effectiveness of goal setting with complex tasks, using group…

  11. Development and Application of Coating Weight Control Technology

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jin Hyoung [Dongbu Steel, Incheon (Korea, Republic of)

    2010-08-15

    Precise coating weight control is very important issue on quality and minimizing operating costs on continuous galvanizing line. These days, many steel making companies are having a new understanding of cost importance by rise raw material prices and customers requirement for cost reduction. Dongbu steel also meets these situations and decided to develop the technologies. Dongbu Steel developed Integrated coating weight control system jointly with Objective Control Ltd. and installed 2CGL and 4CGL. Several technological functions were developed and realized to achieve true hands-off operation and maximum cost benefit by combining model-based preset and dynamic prediction models. We also installed it on 1 CGL on April, 2008. This paper will present the interface, functions and application result of the integrated coating weight control system including Zn saving and coating weight uniformity.

  12. Effect of prematurity and low birth weight in visual abilities and school performance.

    Science.gov (United States)

    Perez-Roche, T; Altemir, I; Giménez, G; Prieto, E; González, I; Peña-Segura, J L; Castillo, O; Pueyo, V

    2016-12-01

    Prematurity and low birth weight are known risk factors for cognitive and developmental impairments, and school failure. Visual perceptual and visual motor skills seem to be among the most affected cognitive domains in these children. To assess the influence of prematurity and low birth weight in visual cognitive skills and school performance. We performed a prospective cohort study, which included 80 boys and girls in an age range from 5 to 13. Subjects were grouped by gestational age at birth (preterm, birth weight (small for gestational age (SGA), school performance in children. Figure-ground skill and visual motor integration were significantly decreased in the preterm birth group, compared with term control subjects (figure-ground: 45.7 vs 66.5, p=0.012; visual motor integration, TVAS: (9.9 vs 11.8, p=0.018), while outcomes of visual memory (29.0 vs 47.7, p=0.012), form constancy (33.3 vs 52.8, p=0.019), figure-ground (37.4 vs 65.6, p=0.001), and visual closure (43.7 vs 62.6 p=0.016) testing were lower in the SGA (vs AGA) group. Visual cognitive difficulties corresponded with worse performance in mathematics (r=0.414, p=0.004) and reading (r=0.343, p=0.018). Specific patterns of visual perceptual and visual motor deficits are displayed by children born preterm or SGA, which hinder mathematics and reading performance. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Modeling of Body Weight Metrics for Effective and Cost-Efficient Conventional Factor VIII Dosing in Hemophilia A Prophylaxis

    Directory of Open Access Journals (Sweden)

    Alanna McEneny-King

    2017-10-01

    Full Text Available The total body weight-based dosing strategy currently used in the prophylactic treatment of hemophilia A may not be appropriate for all populations. The assumptions that guide weight-based dosing are not valid in overweight and obese populations, resulting in overdosing and ineffective resource utilization. We explored different weight metrics including lean body weight, ideal body weight, and adjusted body weight to determine an alternative dosing strategy that is both safe and resource-efficient in normal and overweight/obese adult patients. Using a validated population pharmacokinetic model, we simulated a variety of dosing regimens using different doses, weight metrics, and frequencies; we also investigated the implications of assuming various levels of endogenous factor production. Ideal body weight performed the best across all of the regimens explored, maintaining safety while moderating resource consumption for overweight and obese patients.

  14. Comparison of Cloud backup performance and costs in Oracle database

    Directory of Open Access Journals (Sweden)

    Aljaž Zrnec

    2011-06-01

    Full Text Available Normal 0 21 false false false SL X-NONE X-NONE Current practice of backing up data is based on using backup tapes and remote locations for storing data. Nowadays, with the advent of cloud computing a new concept of database backup emerges. The paper presents the possibility of making backup copies of data in the cloud. We are mainly focused on performance and economic issues of making backups in the cloud in comparison to traditional backups. We tested the performance and overall costs of making backup copies of data in Oracle database using Amazon S3 and EC2 cloud services. The costs estimation was performed on the basis of the prices published on Amazon S3 and Amazon EC2 sites.

  15. Growth Performance, Haematological Indices and Cost Benefits of ...

    African Journals Online (AJOL)

    Lenovo pc

    Effect of replacing dietary maize with cassava peel meal (CPM) supplemented with Allzyme® SSF (SSF) on the growth performance, haematological indices and cost benefits of growing pigs was investigated. Chemical composition of CPM and diets used were determined using standard procedures. Twenty-four growing ...

  16. [The kangaroo mothers' programme: a simple and cost-effective alternative for protecting the premature newborn or low-birth-weight babies].

    Science.gov (United States)

    Lizarazo-Medina, Jenny P; Ospina-Diaz, Juan M; Ariza-Riaño, Nelly E

    2012-06-01

    Describing the efficacy and achievements of the kangaroo mothers' programme (KMP) regarding preterm or low-birth-weight babies' health and development in Hospital San Rafael in Tunja from November 2007 to December 2009. This was a retrospective observational cohort study; 374 infants born prematurely or having low-birth-weight were included to assess household socio-demographic factors, maternal and obstetric history, delivery characteristics and complications and follow-up until 40 weeks post-conception age. There was a high prevalence of teenage pregnancy (17.5 %) and in women older than 35 years (12.6 %), unwanted pregnancy (40.6 %), low quality and poor availability of food in families, complications such as preeclampsia, infection and premature rupture of membranes, 1,969 grams average birth weight, 2,742.9 grams average weight on discharge and 22 grams average weight gain per day. It was found that KMP methodology substantially improved the mothers' psychological aspects and health status and the newborns' prognosis and led to stabilising body temperature and weight gain rate while decreasing risks of complications and nosocomial infection. It also lowered health care costs and shortened hospital stay.

  17. Muscle performance following an acute bout of plyometric training combined with low or high intensity weight exercise.

    Science.gov (United States)

    Beneka, Anastasia G; Malliou, Paraskevi K; Missailidou, Victoria; Chatzinikolaou, Athanasios; Fatouros, Ioannis; Gourgoulis, Vassilios; Georgiadis, Elias

    2013-01-01

    To determine the time course of performance responses after an acute bout of plyometric exercise combined with high and low intensity weight training, a 3-group (including a control group), repeated-measures design was employed. Changes in performance were monitored through jumping ability by measuring countermovement and squat jumping, and strength performance assessment through isometric and isokinetic testing of knee extensors (at two different velocities). Participants in both experimental groups performed a plyometric protocol consisting of 50 jumps over 50 cm hurdles and 50 drop jumps from a 50 cm plyometric box. Additionally, each group performed two basic weight exercises consisting of leg presses and leg extensions at 90-95% of maximum muscle strength for the high intensity group and 60% of maximum muscle strength for the low intensity group. The results of the study suggest that an acute bout of intense plyometric exercise combined with weight exercise induces time-dependent changes in performance, which are also dependent on the nature of exercise protocol and testing procedures. In conclusion, acute plyometric exercise with weight exercise may induce a substantial decline in jumping performance for as long as 72 hours but not in other forms of muscle strength.

  18. Market value calculation and the solution of circularity between value and the weighted average cost of capital WACC

    Directory of Open Access Journals (Sweden)

    Ignacio Vélez-Pareja

    2009-12-01

    Full Text Available Most finance textbooks present the Weighted Average Cost of Capital (WACC calculation as: WACC = Kd×(1-T×D% + Ke×E%, where Kd is the cost of debt before taxes, T is the tax rate, D% is the percentage of debt on total value, Ke is the cost of equity and E% is the percentage of equity on total value. All of them precise (but not with enough emphasis that the values to calculate D% y E% are market values. Although they devote special space and thought to calculate Kd and Ke, little effort is made to the correct calculation of market values. This means that there are several points that are not sufficiently dealt with: Market values, location in time, occurrence of tax payments, WACC changes in time and the circularity in calculating WACC. The purpose of this note is to clear up these ideas, solve the circularity problem and emphasize in some ideas that usually are looked over. Also, some suggestions are presented on how to calculate, or estimate, the equity cost of capital.

  19. Diagnostic performance of dark-blood T2-weighted CMR for evaluation of acute myocardial injury.

    Science.gov (United States)

    Srichai, Monvadi B; Lim, Ruth P; Lath, Narayan; Babb, James; Axel, Leon; Kim, Daniel

    2013-01-01

    We compared the image quality and diagnostic performance of 2 fat-suppression methods for black-blood T2-weighted fast spin-echo (FSE), which are as follows: (a) short T1 inversion recovery (STIR; FSE-STIR) and (b) spectral adiabatic inversion recovery (SPAIR; FSE-SPAIR), for detection of acute myocardial injury. Edema-sensitive T2-weighted FSE cardiac magnetic resonance (CMR) imaging is useful in detecting acute myocardial injury but may experience reduced myocardial signal and signal dropout. The SPAIR pulse aims to eliminate artifacts associated with the STIR pulse. A total of 65 consecutive patients referred for CMR evaluation of myocardial structure and function underwent FSE-STIR and FSE-SPAIR, in addition to cine and late gadolinium enhancement (LGE) CMR. T2-weighted FSE images were independently evaluated by 2 readers for image quality and artifacts (Likert scale of 1-5; best-worst) and presence of increased myocardial signal suggestive of edema. In addition, clinical CMR interpretation, incorporating all CMR sequences available, was recorded for comparison. Diagnostic performance of each T2-weighted sequence was measured using recent (T2, and wall motion. There was a statistically significant difference in sensitivity between the clinical interpretation and each of the T2-weighted sequences but not between each T2-weighted sequence. Although FSE-SPAIR demonstrated significantly improved image quality and decreased artifacts, isolated interpretations of each T2-weighted technique demonstrated high specificity but overall low sensitivity for the detection of myocardial injury, with no difference in accuracy between the techniques. However, real-world interpretation in combination with cine and LGE CMR methods significantly improves the overall sensitivity and diagnostic performance.

  20. Performance and cost assessment of solar driven humidification dehumidification desalination system

    International Nuclear Information System (INIS)

    Zubair, M. Ifras; Al-Sulaiman, Fahad A.; Antar, M.A.; Al-Dini, Salem A.; Ibrahim, Nasiru I.

    2017-01-01

    Highlights: • Optimization of a new HDH system integrated solar evacuated tubes collectors was conducted. • The mathematical models developed for the collector and the HDH system were validated. • A multi-location analysis was then performed for six locations in Saudi Arabia. • Sharurah was found to have the highest annual output and Dhahran the lowest at 19,445 and 16,430 L. • The cost per liter of water produced varies from $0.032 to $0.038, depends on the location. - Abstract: A humidification-dehumidification (HDH) desalination system integrated with solar evacuated tubes was optimized. Then, the optimized system was assessed for the operation in different geographical locations, and the rate of freshwater production and cost per liter were determined in each location. The system design proposed in this paper uses a heat pipe design evacuated tube collector, which performs significantly better based on cost. An HDH desalination system with a closed-air/open-water loop, connected to the collector, was evaluated to determine the optimum operating parameters and the system performance during daytime (from 8 am to 3 pm), as well as the average day of each month for an entire year. The impact of the effectiveness of the humidifier and the dehumidifier, as well as, the number of collectors, were also studied. The analyses were performed for Dhahran, Jeddah, Riyadh, Sharurah, Qassim, and Tabuk to determine the effects of varying the geographical location. Sharurah has the highest calculated productivity of freshwater and Dhahran has the lowest at 19,445 and 16,430 L, respectively. To have a comprehensive study of the system proposed, a cost analysis was also performed to determine the feasibility of the system and the cost of water production. Results show that the price varied from $0.032 to $0.038 per liter for the locations evaluated.

  1. Electrostatic direct energy converter performance and cost scaling laws

    International Nuclear Information System (INIS)

    Hoffman, M.A.

    1977-08-01

    This study is concerned with electrostatic type direct energy converters for direct recovery of a large fraction of the plasma ion energy from fusion reactors. Simplified equations are presented for each of the important loss mechanisms in both single-stage direct converters and multistage ''Venetian Blind'' type direct converters. These equations can be used to estimate the efficiency and electric power output of the direct converter subsystem. Scaling relations for the cost of each major component in the direct converter subsystem are also given; these include the vacuum tank, direct converter modules, the DC power conditioning equipment, cryogenic vacuum pumping system and the thermal bottoming plant. The performance and cost scaling laws have been developed primarily for use in overall fusion power plant systems codes. However, to illustrate their utility, cost-effectiveness studies of two specific reference direct converter designs are presented in terms of the specific capital costs (i.e., the capital cost per unit electric power produced) for the Direct Converter Subsystem alone. Some examples of design improvements which can significantly reduce the specific capital costs of the Direct Converter Subsystem are also given

  2. Costs and Performance of English Mental Health Providers.

    Science.gov (United States)

    Moran, Valerie; Jacobs, Rowena

    2017-06-01

    Despite limited resources in mental health care, there is little research exploring variations in cost performance across mental health care providers. In England, a prospective payment system for mental health care based on patient needs has been introduced with the potential to incentivise providers to control costs. The units of payment under the new system are 21 care clusters. Patients are allocated to a cluster by clinicians, and each cluster has a maximum review period. The aim of this research is to explain variations in cluster costs between mental health providers using observable patient demographic, need, social and treatment variables. We also investigate if provider-level variables explain differences in costs. The residual variation in cluster costs is compared across providers to provide insights into which providers may gain or lose under the new financial regime. The main data source is the Mental Health Minimum Data Set (MHMDS) for England for the years 2011/12 and 2012/13. Our unit of observation is the period of time spent in a care cluster and costs associated with the cluster review period are calculated from NHS Reference Cost data. Costs are modelled using multi-level log-linear and generalised linear models. The residual variation in costs at the provider level is quantified using Empirical Bayes estimates and comparative standard errors used to rank and compare providers. There are wide variations in costs across providers. We find that variables associated with higher costs include older age, black ethnicity, admission under the Mental Health Act, and higher need as reflected in the care clusters. Provider type, size, occupancy and the proportion of formal admissions at the provider-level are also found to be significantly associated with costs. After controlling for patient- and provider-level variables, significant residual variation in costs remains at the provider level. The results suggest that some providers may have to increase

  3. Measuring Healthcare Providers' Performances Within Managed Competition Using Multidimensional Quality and Cost Indicators.

    Science.gov (United States)

    Portrait, France R M; van der Galiën, Onno; Van den Berg, Bernard

    2016-04-01

    The Dutch healthcare system is in transition towards managed competition. In theory, a system of managed competition involves incentives for quality and efficiency of provided care. This is mainly because health insurers contract on behalf of their clients with healthcare providers on, potentially, quality and costs. The paper develops a strategy to comprehensively analyse available multidimensional data on quality and costs to assess and report on the relative performance of healthcare providers within managed competition. We had access to individual information on 2409 clients of 19 Dutch diabetes care groups on a broad range of (outcome and process related) quality and cost indicators. We carried out a cost-consequences analysis and corrected for differences in case mix to reduce incentives for risk selection by healthcare providers. There is substantial heterogeneity between diabetes care groups' performances as measured using multidimensional indicators on quality and costs. Better quality diabetes care can be achieved with lower or higher costs. Routine monitoring using multidimensional data on quality and costs merged at the individual level would allow a systematic and comprehensive analysis of healthcare providers' performances within managed competition. Copyright © 2015 John Wiley & Sons, Ltd.

  4. Technology for low cost solid rocket boosters.

    Science.gov (United States)

    Ciepluch, C.

    1971-01-01

    A review of low cost large solid rocket motors developed at the Lewis Research Center is given. An estimate is made of the total cost reduction obtainable by incorporating this new technology package into the rocket motor design. The propellant, case material, insulation, nozzle ablatives, and thrust vector control are discussed. The effect of the new technology on motor cost is calculated for a typical expandable 260-in. booster application. Included in the cost analysis is the influence of motor performance variations due to specific impulse and weight changes. It is found for this application that motor costs may be reduced by up to 30% and that the economic attractiveness of future large solid rocket motors will be improved when the new technology is implemented.

  5. Peer Review of “LDT Weight Reduction Study with Crash Model, Feasibility and Detailed Cost Analyses – Chevrolet Silverado 1500 Pickup”

    Science.gov (United States)

    The contractor will conduct an independent peer review of FEV’s light-duty truck (LDT) mass safety study, “Light-Duty Vehicle Weight Reduction Study with Crash Model, Feasibility and Detailed Cost Analysis – Silverado 1500”, and its corresponding computer-aided engineering (CAE) ...

  6. Cost and performance analysis of conceptual designs of physical protection systems

    International Nuclear Information System (INIS)

    Hicks, M.J.; Snell, M.S.; Sandoval, J.S.; Potter, C.S.

    1998-01-01

    CPA -- Cost and Performance Analysis -- is a methodology that joins Activity Based Cost (ABC) estimation with performance based analysis of physical protection systems. CPA offers system managers an approach that supports both tactical decision making and strategic planning. Current exploratory applications of the CPA methodology are addressing analysis of alternative conceptual designs. To support these activities, the original architecture for CPA, is being expanded to incorporate results from a suite of performance and consequence analysis tools such as JTS (Joint Tactical Simulation), ERAD (Explosive Release Atmospheric Dispersion) and blast effect models. The process flow for applying CPA to the development and analysis conceptual designs is illustrated graphically

  7. Cost and performance analysis of physical protection systems - a case study

    International Nuclear Information System (INIS)

    Hicks, M.J.; Snell, M.S.; Sandoval, J.S.; Potter, C.S.

    1998-01-01

    Design and analysis of physical protection systems requires (1) identification of mission critical assets; (2) identification of potential threats that might undermine mission capability; (3) identification of the consequences of loss of mission-critical assets (e.g., time and cost to recover required capability and impact on operational readiness); and (4) analysis of the effectiveness of physical protection elements. CPA -- Cost and Performance Analysis -- addresses the fourth of these four issues. CPA is a methodology that joins Activity Based Cost estimation with performance-based analysis of physical protection systems. CPA offers system managers an approach that supports both tactical decision making and strategic planning. Current exploratory applications of the CPA methodology address analysis of alternative conceptual designs. Hypothetical data is used to illustrate this process

  8. Cost-optimal energy performance renovation measures of educational buildings in cold climate

    International Nuclear Information System (INIS)

    Niemelä, Tuomo; Kosonen, Risto; Jokisalo, Juha

    2016-01-01

    Highlights: • The proposed national nZEB target can be cost-effectively achieved in renovations. • Energy saving potential of HVAC systems is significant compared to the building envelope. • Modern renewable energy production technologies are cost-efficient and recommendable. • Improving the indoor climate conditions in deep renovations is recommendable. • Simulation-based optimization method is efficient in building performance analyzes. - Abstract: The paper discusses cost-efficient energy performance renovation measures for typical educational buildings built in the 1960s and 1970s in cold climate regions. The study analyzes the impact of different energy renovation measures on the energy efficiency and economic viability in a Finnish case study educational building located in Lappeenranta University of Technology (LUT) campus area. The main objective of the study was to determine the cost-optimal energy performance renovation measures to meet the proposed national nearly zero-energy building (nZEB) requirements, which are defined according to the primary energy consumption of buildings. The main research method of the study was simulation-based optimization (SBO) analysis, which was used to determine the cost-optimal renovation solutions. The results of the study indicate that the minimum national energy performance requirement of new educational buildings (E_p_r_i_m_a_r_y ⩽ 170 kWh/(m"2,a)) can be cost-effectively achieved in deep renovations of educational buildings. In addition, the proposed national nZEB-targets are also well achievable, while improving the indoor climate (thermal comfort and indoor air quality) conditions significantly at the same time. Cost-effective solutions included renovation of the original ventilation system, a ground source heat pump system with relatively small dimensioning power output, new energy efficient windows and a relatively large area of PV-panels for solar-based electricity production. The results and

  9. Cost-effectiveness of SHINE: A Telephone Translation of the Diabetes Prevention Program

    Directory of Open Access Journals (Sweden)

    Christopher S. Hollenbeak

    2016-01-01

    Full Text Available Background The Support, Health Information, Nutrition, and Exercise (SHINE trial recently showed that a telephone adaptation of the Diabetes Prevention Program (DPP lifestyle intervention was effective in reducing weight among patients with metabolic syndrome. The aim of this study is to determine whether a conference call (CC adaptation was cost effective relative to an individual call (IC adaptation of the DPP lifestyle intervention in the primary care setting. Methods We performed a stochastic cost-effectiveness analysis alongside a clinical trial comparing two telephone adaptations of the DPP lifestyle intervention. The primary outcomes were incremental cost-effectiveness ratios estimated for weight loss, body mass index (BMI, waist circumference, and quality-adjusted life years (QALYs. Costs were estimated from the perspective of society and included direct medical costs, indirect costs, and intervention costs. Results After one year, participants receiving the CC intervention accumulated fewer costs ($2,831 vs. $2,933 than the IC group, lost more weight (6.2 kg vs. 5.1 kg, had greater reduction in BMI (2.1 vs. 1.9, and had greater reduction in waist circumference (6.5 cm vs. 5.9 cm. However, participants in the CC group had fewer QALYs than those in the IC group (0.635 vs. 0.646. The incremental cost-effectiveness ratio for CC vs. IC was $9,250/QALY, with a 48% probability of being cost-effective at a willingness-to-pay of $100,000/QALY. Conclusions CC delivery of the DPP was cost effective relative to IC delivery in the first year in terms of cost per clinical measure (weight lost, BMI, and waist circumference but not in terms of cost per QALY, most likely because of the short time horizon.

  10. The impact of weighted basketball balls in improving certain physical performances via wheelchair basketball players

    Directory of Open Access Journals (Sweden)

    Houcine Benzidane

    2018-04-01

    Full Text Available The research aims to determine the effect of a weighted basketball balls training program on some physical performance via wheelchair basketball players. The sample was selected in an intended manner including 20 players’. Divided into two equal groups (experimental 10 players, control 10 players for the sports season 2016/2017. As protocol experimental, our training program for the experimental group was applied under researchers’ supervision, using Weighted basketball balls in the opposite of control group which used the same program with real weight basketball. All the tests practised (pre or post test  were conducted with the same team and in the same condition based on endurance test (1000 m, speed test (30 m, push the medical ball and dribbling to test the agility. After statistically processing, it was clear that weighted basketball balls as ingrate tool led to the increase of physical performance intended to study. In the opposite of traditional method.

  11. Tribological Performance Optimization of Electroless Ni-P-W Coating Using Weighted Principal Component Analysis

    Directory of Open Access Journals (Sweden)

    S. Roy

    2013-12-01

    Full Text Available The present investigation is an experimental approach to deposit electroless Ni-P-W coating on mild steel substrate and find out the optimum combination of various tribological performances on the basis of minimum friction and wear, using weighted principal component analysis (WPCA. In this study three main tribological parameters are chosen viz. load (A, speed (B and time(C. The responses are coefficient of friction and wear depth. Here Weighted Principal Component Analysis (WPCA method is adopted to convert the multi-responses into single performance index called multiple performance index (MPI and Taguchi L27 orthogonal array is used to design the experiment and to find the optimum combination of tribological parameters for minimum coefficient of friction and wear depth. ANOVA is performed to find the significance of the each tribological process parameters and their interactions. The EDX analysis, SEM and XRD are performed to study the composition and structural aspects.

  12. Reducing Weight for Transportation Applications: Technology Challenges and Opportunities

    Science.gov (United States)

    Taub, Alan I.

    Today's land, sea and air transportation industries — as a business necessity — are focused on technology solutions that will make vehicles more sustainable in terms of energy, the environment, safety and affordability. Reducing vehicle weight is a key enabler for meeting these challenges as well as increasing payload and improving performance. The potential weight reductions from substituting lightweight metals (advanced high-strength steels, aluminum, magnesium and titanium alloys) are well established. For magnesium castings, weight savings of 60% have been reported [1]. The value of weight reduction depends on the transportation sector and ranges from about 5/kg saved for automobiles to over 500/kg saved for aircraft [2]. The challenge is to optimize the material properties and develop robust, high volume, manufacturing technologies and the associated supply chain to fabricate components and subsystems at the appropriate cost for each application.

  13. Effect of fastskin suits on performance, drag, and energy cost of swimming.

    Science.gov (United States)

    Chatard, Jean-Claude; Wilson, Barry

    2008-06-01

    To investigate the effect of fastskin suits on 25- to 800-m performances, drag, and energy cost of swimming. The performances, stroke rate and distance per stroke, were measured for 14 competitive swimmers in a 25-m pool, when wearing a normal suit (N) and when wearing a full-body suit (FB) or a waist-to-ankle suit (L). Passive drag, oxygen uptake, blood lactate, and the perceived exertion were measured in a flume. There was a 3.2% +/- 2.4% performance benefit for all subjects over the six distances covered at maximal speed wearing FB and L when compared with N. When wearing L, the gain was significantly lower (1.8% +/- 2.5%, P energy cost of swimming was significantly reduced when wearing FB and L by 4.5% +/- 5.4% and 5.5% +/- 3.1%, respectively (P energy cost of submaximal swimming and an increased distance per stroke, at the same stroke rates, and reduced freestyle performance time.

  14. Cost-effectiveness of a Population-based Lifestyle Intervention to Promote Healthy Weight and Physical Activity in Non-attenders of Cardiac Rehabilitation.

    Science.gov (United States)

    Cheng, Qinglu; Church, Jody; Haas, Marion; Goodall, Stephen; Sangster, Janice; Furber, Susan

    2016-03-01

    To evaluate the long-term cost-effectiveness of two home-based cardiac rehabilitation (CR) interventions (Healthy Weight (HW) and Physical Activity (PA)) for patients with cardiovascular disease (CVD), who had been referred to cardiac rehabilitation (CR) but had not attended. The interventions consisted of pedometer-based telephone coaching sessions on weight, nutrition and physical activity (HW group) or physical activity only (PA group) and were compared to a control group who received information brochures about physical activity. A cost-effectiveness analysis was conducted using data from two randomised controlled trials. One trial compared HW to PA (PANACHE study), and the second compared PA to usual care. A Markov model was developed which used one risk factor, body mass index (BMI) to determine the CVD risk level and mortality. Patient-level data from the trials were used to determine the transitions to CVD states and healthcare related costs. The model was run for separate cohorts of males and females. Univariate and probabilistic sensitivity analysis were conducted to test the robustness of the results. Given a willingness-to-pay threshold of $50,000/QALY, in the long run, both the HW and PA interventions are cost-effective compared with usual care. While the HW intervention is more effective, it also costs more than both the PA intervention and the control group due to higher intervention costs. However, the HW intervention is still cost-effective relative to the PA intervention for both men and women. Sensitivity analysis suggests that the results are robust. The results of this paper provide evidence of the long-term cost-effectiveness of home-based CR interventions for patients who are referred to CR but do not attend. Both the HW and PA interventions can be recommended as cost-effective home-based CR programs, especially for people lacking access to hospital services or who are unable to participate in traditional CR programs. Copyright © 2015

  15. Older members perform better in an internet-based behavioral weight loss program compared to younger members.

    Science.gov (United States)

    van der Mark, Marianne; Jonasson, Josefine; Svensson, Madeleine; Linné, Yvonne; Rossner, Stephan; Lagerros, Ylva Trolle

    2009-01-01

    New technology offers increased opportunities for weight control. However, it is not clear whether older people with less computer training can make use of this tool. Our objective was to examine how members above the age of 65 years performed in an internet-based behavioral weight loss program, compared to younger members. Data from members (n = 23,233) of an internet-based behavioral weight loss program were analyzed. We restricted our study to active participants accessing the weight club, during a 6-month period (n = 4,440). The number of logins, food intake, and weight records were examined. Participants were divided into age tertiles separately for men and women. The oldest tertile was further subdivided into two groups: above and below the age of 65 years. Participants aged 65 or older were more likely to remain active in the weight club for at least 6 months compared to younger age groups. They had the highest frequency of recordings of food intake and current weight. Among women, those older than 65 years had on average the highest percentage of weight loss (5.6 kg, 6.8%). Men above 65 years of age had the highest number of logins, on average 161 times during the 6-month period. Older participants are performing equally well or even better in an internet-based behavioral weight loss program than younger participants. Internet-based programs could be a promising and attractive option for older adults requiring assistance in losing weight. 2009 S. Karger AG, Basel.

  16. Innovative High-Performance Deposition Technology for Low-Cost Manufacturing of OLED Lighting

    Energy Technology Data Exchange (ETDEWEB)

    Scott, David; Hamer, John

    2017-06-30

    In this project, OLEDWorks developed and demonstrated the innovative high-performance deposition technology required to deliver dramatic reductions in the cost of manufacturing OLED lighting in production equipment. The current high manufacturing cost of OLED lighting is the most urgent barrier to its market acceptance. The new deposition technology delivers solutions to the two largest parts of the manufacturing cost problem – the expense per area of good product for organic materials and for the capital cost and depreciation of the equipment. Organic materials cost is the largest expense item in the bill of materials and is predicted to remain so through 2020. The high-performance deposition technology developed in this project, also known as the next generation source (NGS), increases material usage efficiency from 25% found in current Gen2 deposition technology to 60%. This improvement alone results in a reduction of approximately $25/m2 of good product in organic materials costs, independent of production volumes. Additionally, this innovative deposition technology reduces the total depreciation cost from the estimated value of approximately $780/m2 of good product for state-of-the-art G2 lines (at capacity, 5-year straight line depreciation) to $170/m2 of good product from the OLEDWorks production line.

  17. Blade size and weight effects in shovel design.

    Science.gov (United States)

    Freivalds, A; Kim, Y J

    1990-03-01

    The shovel is a basic tool that has undergone only nominal systematic design changes. Although previous studies found shovel-weight and blade-size effects of shovelling, the exact trade-off between the two has not been quantified. Energy expenditure, heart rate, ratings of perceived exertion and shovelling performance were measured on five subjects using five shovels with varying blade sizes and weights to move sand. Energy expenditure, normalised to subject weight and load handled, varied quadratically with the blade-size/shovel-weight (B/W) ratio. Minimum energy cost was at B/W = 0.0676 m2/kg, which for an average subject and average load would require an acceptable 5.16 kcal/min of energy expenditure. Subjects, through the ratings of perceived exertion, also strongly preferred the lighter shovels without regard to blade size. Too large a blade or too heavy a shovel increased energy expenditure beyond acceptable levels, while too small a blade reduced efficiency of the shovelling.

  18. The hidden cost of investment. The impact of adjustment costs on firm performance measurement and regulation

    International Nuclear Information System (INIS)

    Nick, Sebastian; Wetzel, Heike

    2014-01-01

    In this study, we address a major problem in the measurement of firm performance and the regulation of natural monopolies, namely the intertemporal character of long-term investment decisions. In specific, we focus on the impact of adjustment costs of investments on estimates of firms' technical and cost inefficiency. We apply nonparametric dynamic data envelopment analysis to investigate the dynamic inefficiency of electricity distribution and transmission companies in the US during the years 2004 to 2011 and compare our results with their static counterparts. Our empirical findings reveal that ignoring long-term investments and their corresponding adjustment costs does significantly distort both firm-specific and industrial inefficiency estimates and may thus create misleading incentives for the regulated firms to cut investments.

  19. 19 CFR 10.178 - Direct costs of processing operations performed in the beneficiary developing country.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Direct costs of processing operations performed in... processing operations performed in the beneficiary developing country. (a) Items included in the direct costs of processing operations. As used in § 10.176, the words “direct costs of processing operations...

  20. Performance on the Iowa gambling task is related to magnitude of weight loss and salivary cortisol in a diet-induced weight loss intervention in overweight women

    Science.gov (United States)

    The overall objective of this study was to examine the relationship between executive function, specifically decision making, and weight loss. We used the Iowa Gambling Task (IGT) to characterize decision making and compared performance on this task to weight loss in obese women (n=29) participatin...

  1. Normal weight children have higher cognitive performance - Independent of physical activity, sleep, and diet.

    Science.gov (United States)

    Hjorth, Mads F; Sørensen, Louise B; Andersen, Rikke; Dyssegaard, Camilla B; Ritz, Christian; Tetens, Inge; Michaelsen, Kim F; Astrup, Arne; Egelund, Niels; Sjödin, Anders

    2016-10-15

    Aside from the health consequences, observational studies indicate that being overweight may also negatively affect cognitive function. However, existing evidence has to a large extent not controlled for the possible confounding effect of having different lifestyles. Therefore, the objective was to examine the independent associations between weight status and lifestyle indicators with cognitive performance in 8-11year old Danish children. The analyses included 828 children (measured in 2011-2012) each having one to three measurement occasions separated by approximately 100days. Dietary intake, physical activity, sedentary time, and sleep duration were measured using dietary records and accelerometers. The Children's Sleep Habits Questionnaire was used to access sleep problems and the Andersen test was carried out to estimate cardio-respiratory fitness (CRF). Weight status (underweight, normal weight, and overweight/obese) was defined according to body mass index and cognitive performance was assessed using the d2-test of attention, a reading test, and a math test. A linear mixed model including a number of fixed and random effects was used to test associations between lifestyle indicators as well as BMI category and cognitive performance. After adjustment for demographics, socioeconomics, and multiple lifestyle indicators, normal weight children had higher cognitive test scores than overweight/obese and underweight children of up to 89% and 48% of expected learning within one school year (Pbreakfast consumption, fewer sleep problems, higher CRF, less total physical activity, more sedentary time, and less light physical activity were associated with higher cognitive performance independently of each other in at least one of the three cognitive tests (Pperformance compared to overweight/obese as well as underweight children, independent of multiple lifestyle indicators. Copyright © 2016 Elsevier Inc. All rights reserved.

  2. Lifting the weight of a diagnosis-related groups family change: a comparison between refined and non-refined DRG systems for top-down cost accounting and efficiency indicators.

    Science.gov (United States)

    Zlotnik, Alexander; Cuchi, Miguel Alfaro; Pérez Pérez, Maria Carmen

    Public healthcare providers in all Spanish Regions - Autonomous Communities (ACs) use All Patients Diagnosis-Related Groups (AP-DRGs) for billing non-insured patients, cost accounting and inpatient efficiency indicators. A national migration to All Patients Refined Diagnosis-Related Groups (APR-DRGs) has been scheduled for 2016. The analysis was performed on 202,912 inpatient care episodes ranging from 2005 to 2010. All episodes were grouped using AP-DRG v25.0 and APR-DRG v24.0. Normalised DRG weight variations for an AP-DRG to APR-DRG migration scenario were calculated and compared. Major differences exist between normalised weights for inpatient episodes depending on the DRGs family used. The usage of the APR-DRG system in Spain without any adjustments, as it was developed in the United States, should be approached with care. In order to avoid reverse incentives and provider financial risks, coding practices should be reviewed and structural differences between DRG families taken into account.

  3. Appraisal of the Performance of Contingency Cost Provision for ...

    African Journals Online (AJOL)

    The paper appraised performance of contingency allowance in addressing projects' cost risk. To achieve this aim, impact of contingency provision in some selected building projects were evaluated. Data for the study was collected by means of checklist from 40 completed projects' files. Furthermore, 100 questionnaires on ...

  4. Cost/schedule performance measurement system utilized on the Fast Flux Test Facility project

    International Nuclear Information System (INIS)

    Brown, R.K.; Frost, R.A.; Zimmerman, F.M.

    1976-01-01

    An Earned Value-Integrated Cost/Schedule Performance Measurement System has been applied to a major nonmilitary nuclear design and construction project. This system is similar to the Department of Defense Cost/Schedule Performance Measurement System. The project is the Fast Flux Test Facility (a Fuels and Materials test reactor for the Liquid Metal Fast Breeder Reactor Program) being built at the Hanford Engineering Development Laboratory, Richland, Washington, by Westinghouse Hanford Company for the U. S. Energy Research and Development Administration. Because the project was well into the construction phase when the Earned Value System was being considered, it was decided that the principles of DOD's Cost/Schedule Control System Criteria would be applied to the extent possible but no major changes in accounting practices or management systems were imposed. Implementation of this system enabled the following questions to be answered: For work performed, how do actual costs compare with the budget for that work. What is the impact of cost and schedule variances at an overall project level composed of different kinds of activities. Without the Earned Value system, these questions could be answered in a qualitative, subjective manner at best

  5. Lysine supplementation in late gestation of gilts: effects on piglet birth weight, and gestational and lactational performance

    Directory of Open Access Journals (Sweden)

    Diogo Magnabosco

    2013-08-01

    Full Text Available Lysine requirements for gain in maternal body reserves and piglet birth weight, during pregnancy, in contemporary prolific genotypes, are not well established. This study aimed to evaluate the effect of dietary lysine in late pregnancy on piglet birth weight, and on the gestational and lactational performance of gilts. Pregnant gilts were uniformly distributed into two groups and received, from 85 to 110 days of gestation, either of two lysine levels in their diet: Control group - 28g lysine/day (n=136, and Lysine group - 35g lysine/day (n=141. There were no effects (P>0.10 of supplemental lysine on body weight and backfat (BF gain of females or on piglet birth weight. Gilts supplemented with lysine tended to have a lower percentage of stillbirths (P=0.077, reduced within-litter birth weight variation (P=0.094 and a lower percentage of piglets weighing less than 1100g (P=0.082 than in the Control group. During lactation, the performance of sows and litters was also evaluated in a subgroup of sows (n=26/group. There were no differences between the Control and Lysine groups (P>0.10 in voluntary feed intake, body reserve losses (weight and BF, weaning-to-estrus interval of the sows, and litter weaning weight. In conclusion, an increase in lysine (from 28 to 35g/day in late gestation of gilts (85 to 110 days tends to reduce the rate of stillbirths and to improve the uniformity of litter weight at birth, but does not affect the performance of females until farrowing or during subsequent lactation.

  6. Low-cost high-quality crystalline germanium based flexible devices

    KAUST Repository

    Nassar, Joanna M.

    2014-06-16

    High performance flexible electronics promise innovative future technology for various interactive applications for the pursuit of low-cost, light-weight, and multi-functional devices. Thus, here we show a complementary metal oxide semiconductor (CMOS) compatible fabrication of flexible metal-oxide-semiconductor capacitors (MOSCAPs) with high-κ/metal gate stack, using a physical vapor deposition (PVD) cost-effective technique to obtain a high-quality Ge channel. We report outstanding bending radius ~1.25 mm and semi-transparency of 30%.

  7. Low-cost high-quality crystalline germanium based flexible devices

    KAUST Repository

    Nassar, Joanna M.; Hussain, Aftab M.; Rojas, Jhonathan Prieto; Hussain, Muhammad Mustafa

    2014-01-01

    High performance flexible electronics promise innovative future technology for various interactive applications for the pursuit of low-cost, light-weight, and multi-functional devices. Thus, here we show a complementary metal oxide semiconductor (CMOS) compatible fabrication of flexible metal-oxide-semiconductor capacitors (MOSCAPs) with high-κ/metal gate stack, using a physical vapor deposition (PVD) cost-effective technique to obtain a high-quality Ge channel. We report outstanding bending radius ~1.25 mm and semi-transparency of 30%.

  8. Particle Swarm Optimization with Various Inertia Weight Variants for Optimal Power Flow Solution

    Directory of Open Access Journals (Sweden)

    Prabha Umapathy

    2010-01-01

    Full Text Available This paper proposes an efficient method to solve the optimal power flow problem in power systems using Particle Swarm Optimization (PSO. The objective of the proposed method is to find the steady-state operating point which minimizes the fuel cost, while maintaining an acceptable system performance in terms of limits on generator power, line flow, and voltage. Three different inertia weights, a constant inertia weight (CIW, a time-varying inertia weight (TVIW, and global-local best inertia weight (GLbestIW, are considered with the particle swarm optimization algorithm to analyze the impact of inertia weight on the performance of PSO algorithm. The PSO algorithm is simulated for each of the method individually. It is observed that the PSO algorithm with the proposed inertia weight yields better results, both in terms of optimal solution and faster convergence. The proposed method has been tested on the standard IEEE 30 bus test system to prove its efficacy. The algorithm is computationally faster, in terms of the number of load flows executed, and provides better results than other heuristic techniques.

  9. Costing and performance in healthcare management

    OpenAIRE

    Tarricone, Rosanna; Torbica, Aleksandra

    2012-01-01

    This chapter describes and discusses the methods for cost analysis of healthcare services in order to assess and compare the economic value of health outputs at the level of healthcare organizations. The economic principles underpinning the assessment of the value of healthcare services – opportunity costs and shadow prices – are presented together with the management accounting approach to cost services. The key features of micro-costing and gross-costing are also discussed and their rele...

  10. Performance and cost evaluation of health information systems using micro-costing and discrete-event simulation.

    Science.gov (United States)

    Rejeb, Olfa; Pilet, Claire; Hamana, Sabri; Xie, Xiaolan; Durand, Thierry; Aloui, Saber; Doly, Anne; Biron, Pierre; Perrier, Lionel; Augusto, Vincent

    2018-06-01

    Innovation and health-care funding reforms have contributed to the deployment of Information and Communication Technology (ICT) to improve patient care. Many health-care organizations considered the application of ICT as a crucial key to enhance health-care management. The purpose of this paper is to provide a methodology to assess the organizational impact of high-level Health Information System (HIS) on patient pathway. We propose an integrated performance evaluation of HIS approach through the combination of formal modeling using the Architecture of Integrated Information Systems (ARIS) models, a micro-costing approach for cost evaluation, and a Discrete-Event Simulation (DES) approach. The methodology is applied to the consultation for cancer treatment process. Simulation scenarios are established to conclude about the impact of HIS on patient pathway. We demonstrated that although high level HIS lengthen the consultation, occupation rate of oncologists are lower and quality of service is higher (through the number of available information accessed during the consultation to formulate the diagnostic). The provided method allows also to determine the most cost-effective ICT elements to improve the care process quality while minimizing costs. The methodology is flexible enough to be applied to other health-care systems.

  11. Development and Performance Evaluation of a Low Cost Waste ...

    African Journals Online (AJOL)

    The design, development and performance evaluation of a low cost waste-water treatment plant had been carried out. The aim was to harness the usefulness of waste-waters from residential, institutional and commercial sources. The facultative lagoon method of waste-water treatment was adopted. Biological analysis of ...

  12. Safeguards First Principle Initiative (SFPI) Cost Model

    International Nuclear Information System (INIS)

    Price, Mary Alice

    2010-01-01

    The Nevada Test Site (NTS) began operating Material Control and Accountability (MC and A) under the Safeguards First Principle Initiative (SFPI), a risk-based and cost-effective program, in December 2006. The NTS SFPI Comprehensive Assessment of Safeguards Systems (COMPASS) Model is made up of specific elements (MC and A plan, graded safeguards, accounting systems, measurements, containment, surveillance, physical inventories, shipper/receiver differences, assessments/performance tests) and various sub-elements, which are each assigned effectiveness and contribution factors that when weighted and rated reflect the health of the MC and A program. The MC and A Cost Model, using an Excel workbook, calculates budget and/or actual costs using these same elements/sub-elements resulting in total costs and effectiveness costs per element/sub-element. These calculations allow management to identify how costs are distributed for each element/sub-element. The Cost Model, as part of the SFPI program review process, enables management to determine if spending is appropriate for each element/sub-element.

  13. High performance cone-beam spiral backprojection with voxel-specific weighting

    International Nuclear Information System (INIS)

    Steckmann, Sven; Knaup, Michael; Kachelriess, Marc

    2009-01-01

    Cone-beam spiral backprojection is computationally highly demanding. At first sight, the backprojection requirements are similar to those of cone-beam backprojection from circular scans such as it is performed in the widely used Feldkamp algorithm. However, there is an additional complication: the illumination of each voxel, i.e. the range of angles the voxel is seen by the x-ray cone, is a complex function of the voxel position. In general, one needs to multiply a voxel-specific weight w(x, y, z, α) prior to adding a projection from angle α to a voxel at position x, y, z. Often, the weight function has no analytically closed form and must be numerically determined. Storage of the weights is prohibitive since the amount of memory required equals the number of voxels per spiral rotation times the number of projections a voxel receives contributions and therefore is in the order of up to 10 12 floating point values for typical spiral scans. We propose a new algorithm that combines the spiral symmetry with the ability of today's 64 bit operating systems to store large amounts of precomputed weights, even above the 4 GB limit. Our trick is to backproject into slices that are rotated in the same manner as the spiral trajectory rotates. Using the spiral symmetry in this way allows one to exploit data-level paralellism and thereby to achieve a very high level of vectorization. An additional postprocessing step rotates these slices back to normal images. Our new backprojection algorithm achieves up to 17 giga voxel updates per second on our systems that are equipped with four standard Intel X7460 hexa core CPUs (Intel Xeon 7300 platform, 2.66 GHz, Intel Corporation). This equals the reconstruction of 344 images per second assuming that each slice consists of 512 x 512 pixels and receives contributions from 512 projections. Thereby, it is an order of magnitude faster than a highly optimized code that does not make use of the spiral symmetry. In its present version, the

  14. High performance cone-beam spiral backprojection with voxel-specific weighting

    Science.gov (United States)

    Steckmann, Sven; Knaup, Michael; Kachelrieß, Marc

    2009-06-01

    Cone-beam spiral backprojection is computationally highly demanding. At first sight, the backprojection requirements are similar to those of cone-beam backprojection from circular scans such as it is performed in the widely used Feldkamp algorithm. However, there is an additional complication: the illumination of each voxel, i.e. the range of angles the voxel is seen by the x-ray cone, is a complex function of the voxel position. In general, one needs to multiply a voxel-specific weight w(x, y, z, α) prior to adding a projection from angle α to a voxel at position x, y, z. Often, the weight function has no analytically closed form and must be numerically determined. Storage of the weights is prohibitive since the amount of memory required equals the number of voxels per spiral rotation times the number of projections a voxel receives contributions and therefore is in the order of up to 1012 floating point values for typical spiral scans. We propose a new algorithm that combines the spiral symmetry with the ability of today's 64 bit operating systems to store large amounts of precomputed weights, even above the 4 GB limit. Our trick is to backproject into slices that are rotated in the same manner as the spiral trajectory rotates. Using the spiral symmetry in this way allows one to exploit data-level paralellism and thereby to achieve a very high level of vectorization. An additional postprocessing step rotates these slices back to normal images. Our new backprojection algorithm achieves up to 17 giga voxel updates per second on our systems that are equipped with four standard Intel X7460 hexa core CPUs (Intel Xeon 7300 platform, 2.66 GHz, Intel Corporation). This equals the reconstruction of 344 images per second assuming that each slice consists of 512 × 512 pixels and receives contributions from 512 projections. Thereby, it is an order of magnitude faster than a highly optimized code that does not make use of the spiral symmetry. In its present version, the

  15. Does Accumulated Knowledge Impact Academic Performance in Cost Accounting?

    Science.gov (United States)

    Alanzi, Khalid A.; Alfraih, Mishari M.

    2017-01-01

    Purpose: This quantitative study aims to examine the impact of accumulated knowledge of accounting on the academic performance of Cost Accounting students. Design/methodology/approach The sample consisted of 89 students enrolled in the Accounting program run by a business college in Kuwait during 2015. Correlation and linear least squares…

  16. Cost analysis of injection laryngoplasty performed under local anaesthesia versus general anaesthesia: an Australian perspective.

    Science.gov (United States)

    Chandran, D; Woods, C M; Schar, M; Ma, N; Ooi, E H; Athanasiadis, T

    2018-02-01

    To conduct a cost analysis of injection laryngoplasty performed in the operating theatre under local anaesthesia and general anaesthesia. The retrospective study included patients who had undergone injection laryngoplasty as day cases between July 2013 and March 2016. Cost data were obtained, along with patient demographics, anaesthetic details, type of injectant, American Society of Anesthesiologists score, length of stay, total operating theatre time and surgeon procedure time. A total of 20 cases (general anaesthesia = 6, local anaesthesia = 14) were included in the cost analysis. The mean total cost under general anaesthesia (AU$2865.96 ± 756.29) was significantly higher than that under local anaesthesia (AU$1731.61 ± 290.29) (p costs. Procedures performed under local anaesthesia in the operating theatre are associated with shorter operating theatre time and length of stay in the hospital, and provide significant cost savings. Further savings could be achieved if local anaesthesia procedures were performed in the office setting.

  17. Light-weight plastination.

    Science.gov (United States)

    Steinke, Hanno; Rabi, Suganthy; Saito, Toshiyuki; Sawutti, Alimjan; Miyaki, Takayoshi; Itoh, Masahiro; Spanel-Borowski, Katharina

    2008-11-20

    Plastination is an excellent technique which helps to keep the anatomical specimens in a dry, odourless state. Since the invention of plastination technique by von Hagens, research has been done to improve the quality of plastinated specimens. In this paper, we have described a method of producing light-weight plastinated specimens using xylene along with silicone and in the final step, substitute xylene with air. The finished plastinated specimens were light-weight, dry, odourless and robust. This method requires less use of resin thus making the plastination technique more cost-effective. The light-weight specimens are easy to carry and can easily be used for teaching.

  18. Effect of density and weight of load on the energy cost of carrying loads by donkeys and ponies.

    Science.gov (United States)

    Pearson, R A; Dijkman, J T; Krecek, R C; Wright, P

    1998-02-01

    Two experiments were designed to compare the energy used in carrying loads by donkeys and ponies. In the first experiment 3 donkeys and 3 ponies were compared on treadmills in the UK. Density of load (lead shot or straw) had no significant effect on the energy cost of carrying loads; however, the energy cost of carrying a load decreased significantly (p < 0.001) as the weight of the load increased (in donkeys 6.44, 4.35 and 3.03 J/kg load/m, in ponies 5.82, 3.75 and 3.68 J/kg load/m, for loads of 13, 20 and 27 kg/100 kg liveweight (M) respectively). Differences between species were not significant. In the second experiment energy expenditures were determined in 3 donkeys carrying loads equivalent to 40 kg/100 kg M over gently undulating gravel tracks in Tunisia. Energy costs of carrying the load were 2.34 (SE 0.07) J/kg load/m. The results of both experiments showed that provided the load is balanced, density does not significantly affect the energy cost of carrying; however, as the load increased then the unit energy cost of carrying it decreased. This suggest that it is more efficient in terms of energy used to carry loads equivalent to 27 to 40 kg/100 kg M than it is to carry lighter loads to less than 20 kg/100 kg M.

  19. Completion rates of anterior and posterior continuous curvilinear capsulorrhexis in pediatric cataract surgery for surgery performed by trainee surgeons with the use of a low-cost viscoelastic

    Directory of Open Access Journals (Sweden)

    R Muralidhar

    2012-01-01

    Full Text Available Context : Pediatric cataract surgery is traditionally done with the aid of high-molecular-weight viscoelastics which are expensive. It needs to be determined if low-cost substitutes are just as successful. Aims : The study aims to determine the success rates for anterior and posterior capsulorrhexis and intraocular lens (IOL implantation in the bag for pediatric cataract surgery performed with the aid of a low-molecular-weight viscoelastic. Settings and Design : Nonrandomized observational study. Materials and Methods: Children less than 6 years of age who underwent cataract surgery with IOL implantation in the period May 2008-May 2009 were included. The surgeries were done by pediatric ophthalmology fellows. A standard procedure of anterior capsulorrhexis, lens aspiration with primary posterior capsulorrhexis, anterior vitrectomy, and IOL implantation was followed. Three parameters were studied: successful completion of anterior and posterior capsulorrhexis and IOL implantation in the bag. Results: 33 eyes of 28 children were studied. The success rate for completion was 66.7% and 88.2 % for anterior and posterior capsulorrhexis, respectively. IOL implantation in the bag was successful in 87.9%. Conclusions: 2% hydroxypropylmethylcellulose is a viable low-cost alternative to more expensive options similar to high-molecular-weight viscoelastics. This is of great relevance to hospitals in developing countries.

  20. Performance, Process, and Costs: Managing Service Quality with the Balanced Scorecard.

    Science.gov (United States)

    Poll, Roswitha

    2001-01-01

    Describes a cooperative project among three German libraries that used the Balanced Scorecard as a concept for an integrated quality management system. Considers performance indicators across four perspectives that will help academic libraries establish an integrated controlling system and to collect and evaluate performance as well as cost data…

  1. Cost-effectiveness of pharmacotherapy to reduce obesity.

    Directory of Open Access Journals (Sweden)

    J Lennert Veerman

    Full Text Available AIMS: Obesity causes a high disease burden in Australia and across the world. We aimed to analyse the cost-effectiveness of weight reduction with pharmacotherapy in Australia, and to assess its potential to reduce the disease burden due to excess body weight. METHODS: We constructed a multi-state life-table based Markov model in Excel in which body weight influences the incidence of stroke, ischemic heart disease, hypertensive heart disease, diabetes mellitus, osteoarthritis, post-menopausal breast cancer, colon cancer, endometrial cancer and kidney cancer. We use data on effectiveness identified from PubMed searches, on mortality from Australian Bureau of Statistics, on disease costs from the Australian Institute of Health and Welfare, and on drug costs from the Department of Health and Ageing. We evaluate 1-year pharmacological interventions with sibutramine and orlistat targeting obese Australian adults free of obesity-related disease. We use a lifetime horizon for costs and health outcomes and a health sector perspective for costs. Incremental Cost-Effectiveness Ratios (ICERs below A$50 000 per Disability Adjusted Life Year (DALY averted are considered good value for money. RESULTS: The ICERs are A$130 000/DALY (95% uncertainty interval [UI] 93 000-180 000 for sibutramine and A$230 000/DALY (170 000-340 000 for orlistat. The interventions reduce the body weight-related disease burden at the population level by 0.2% and 0.1%, respectively. Modest weight loss during the interventions, rapid post-intervention weight regain and low adherence limit the health benefits. CONCLUSIONS: Treatment with sibutramine or orlistat is not cost-effective from an Australian health sector perspective and has a negligible impact on the total body weight-related disease burden.

  2. The Effects of Collaboration on Logistical Performance and Transaction Costs

    Directory of Open Access Journals (Sweden)

    Vieira, J.G.V.

    2015-05-01

    Full Text Available This paper assesses the effect of supplier-retailer collaboration on logistical performance and transaction costs from the viewpoint of retail sector suppliers. The methodology consists of an empirical study conducted over nine months in the logistics department of a large Brazilian supermarket retailer and a survey of 125 representatives of 90 manufacturers. The results show collaboration contributes to an improvement in logistical performance related to urgent deliveries and deliveries that occur during periods of high demand. Interpersonal collaboration and joint actions contribute to the reduction of uncertainties among the participants. These joint actions, together with strategic collaboration, contribute to an increase in investment in specific assets, such as dedicated production lines or specialised vehicle fleets to serve partners. The study provides an analysis of logistical performance and transaction cost elements not previously investigated, including urgent deliveries and deliveries during periods of high demand, contract negotiation and renegotiation, waiting time for agreements to be reached, contingency logistics planning, and various cultural, psychosocial and geographical aspects of the supplier-retailer relationship. Managerial implications, research limitation and future research are also discussed.

  3. Building Cost and Performance Metrics: Data Collection Protocol, Revision 1.0

    Energy Technology Data Exchange (ETDEWEB)

    Fowler, Kimberly M.; Solana, Amy E.; Spees, Kathleen L.

    2005-09-29

    This technical report describes the process for selecting and applying the building cost and performance metrics for measuring sustainably designed buildings in comparison to traditionally designed buildings.

  4. Monitoring worksite clinic performance using a cost-benefit tool.

    Science.gov (United States)

    Tao, Xuguang; Chenoweth, David; Alfriend, Amy S; Baron, David M; Kirkland, Tracie W; Scherb, Jill; Bernacki, Edward J

    2009-10-01

    The purpose of this study was to explore the usefulness of continuously assessing the return on investment (ROI) of worksite medical clinics as a means of evaluating clinic performance. Visit data from January 1, 2007, to December 31, 2008, were collected from all the on-site clinics operated for the Pepsi Bottling Group. An average system-wide ROI was calculated from the time of each clinic's opening and throughout the study period. A multivariate linear regression model was used to determine the association of average ROI with penetration/utilization rate and plant size. A total of 26 on-site clinics were actively running as of December 2008. The average ROI at the time of start up was 0.4, which increased to 1.2 at approximately 4 months and 1.6 at the end of the first year of operation. Overall, it seems that the cost of operating a clinic becomes equal to the cost of similar care purchased in the community (ROI = 1) at approximately 3 months after a clinic's opening and flattens out at the end of the first year. The magnitude of the ROI was closely related to the number of visits (a function of the penetration/utilization rate) and the size of the plant population served. Serial monitoring of ROIs is a useful metric in assessing on-site clinic performance and quantifying the effect of new initiatives aimed at increasing a clinic's cost effectiveness.

  5. The Relationship between Cost Leadership Strategy, Total Quality Management Applications and Financial Performance

    Directory of Open Access Journals (Sweden)

    Ali KURT

    2016-03-01

    Full Text Available Firms need to implement some competition strategies and total quality management applications to overcome the fierce competition among others. The purpose of this study is to show the relationship between cost leadership strategy, total quality management applications and firms’ financial performance with literature review and empirical analysis. 449 questionnaires were conducted to the managers of 142 big firms. The data gathered was assessed with AMOS. As a result, the relationship between cost leadership strategy, total quality management applications and firms’ financial performance has been gathered. In addition, the relationship between TQM applications and financial performance has also been gathered.

  6. Effect of Changing Weight and Mass on Human Performance in a Lunar Prototype Spacesuit

    Science.gov (United States)

    Chappell, Steve; Lee, Lesley; Gemhardt, Mike

    2010-01-01

    Physical effort, compensation, and controllability in a spacesuit can be affected by suit mass and gravity level. Because of limitations in certain reduced-gravity simulators and the finite selection of lunar prototype suits, it is difficult to ascertain how a change in suit mass affects suited human performance. One method of simulating a change in mass is to vary the total gravity-adjusted weight (TGAW), which is defined as the sum of the suit mass and subject mass, multiplied by the gravity level. PURPOSE: To determine if two methods of changing TGAW during parabolic flight - changing suit mass or gravity level - affect subjective ratings of suited human performance equally.METHODS: A custom weight support structure was connected to a lunar prototype spacesuit, allowing the addition of mass to the suit while maintaining a near-constant center of mass. In the varied-weight (VW) series, suit mass (120 kg) was constant at 0.1-g, 0.17-g, and 0.3-g, yielding TGAWs of 196, 333, and 588 N, assuming an 80-kg subject. In the varied-mass (VM) series, gravity level was constant at 0.17-g and suit mass was 89, 120, and 181 kg, yielding TGAWs of 282, 333, and 435 N. The 333 N condition was common to both series. Direct comparison was not possible due to limited adjustability of suit mass and limited options for parabolic profiles. Five astronaut subjects (80.311.8 kg) completed 4 different tasks (walk, bag pickup, lunge, and shoveling) in all conditions and provided ratings of perceived exertion (RPE) and the gravity compensation and performance scale (GCPS) upon completion of each task. RESULTS: Where VM and VW series overlapped, RPE and GCPS trend lines were similar. Mean RPE and GCPS at 333 N was 8.4 and 3.7. Mean RPE and GCPS for VM was 7.8 and 3.8 for 282 N and 9.8 and 4.1 for 435 N. Extrapolation of the VM trend to match VW TGAWs 196 and 588 N predicts an RPE of 6.5 and 12.3 and GCPS of 4.4 and 5.9, whereas the measured VW values for RPE were 8.1 and 9.8 and GCPS were

  7. Lack of Effect of Typical Rapid-Weight-Loss Practices on Balance and Anaerobic Performance in Apprentice Jockeys.

    Science.gov (United States)

    Cullen, SarahJane; Dolan, Eimear; O Brien, Kate; McGoldrick, Adrian; Warrington, Giles

    2015-11-01

    Balance and anaerobic performance are key attributes related to horse-racing performance, but research on the impact of making weight for racing on these parameters remains unknown. The purpose of this study was to investigate the effects of rapid weight loss in preparation for racing on balance and anaerobic performance in a group of jockeys. Twelve apprentice male jockeys and 12 age- and gender-matched controls completed 2 trials separated by 48 h. In both trials, body mass, hydration status, balance, and anaerobic performance were assessed. Between the trials, the jockeys reduced body mass by 4% using weight-loss methods typically adopted in preparation for racing, while controls maintained body mass through typical daily dietary and physical activity habits. Apprentice jockeys decreased mean body mass by 4.2% ± 0.3% (P balance, on the left or right side, or in peak power, mean power, or fatigue index were reported between the trials in either group. Results from this study indicate that a 4% reduction in body mass in 48 h through the typical methods employed for racing, in association with an increase in dehydration, resulted in no impairments in balance or anaerobic performance. Further research is required to evaluate performance in a sport-specific setting and to investigate the specific physiological mechanisms involved.

  8. A systematic review of the cost of data collection for performance monitoring in hospitals.

    Science.gov (United States)

    Jones, Cheryl; Gannon, Brenda; Wakai, Abel; O'Sullivan, Ronan

    2015-04-01

    Key performance indicators (KPIs) are used to identify where organisational performance is meeting desired standards and where performance requires improvement. Valid and reliable KPIs depend on the availability of high-quality data, specifically the relevant minimum data set ((MDS) the core data identified as the minimum required to measure performance for a KPI) elements. However, the feasibility of collecting the relevant MDS elements is always a limitation of performance monitoring using KPIs. Preferably, data should be integrated into service delivery, and, where additional data are required that are not currently collected as part of routine service delivery, there should be an economic evaluation to determine the cost of data collection. The aim of this systematic review was to synthesise the evidence base concerning the costs of data collection in hospitals for performance monitoring using KPI, and to identify hospital data collection systems that have proven to be cost minimising. We searched MEDLINE (1946 to May week 4 2014), Embase (1974 to May week 2 2014), and CINAHL (1937 to date). The database searches were supplemented by searching for grey literature through the OpenGrey database. Data was extracted, tabulated, and summarised as part of a narrative synthesis. The searches yielded a total of 1,135 publications. After assessing each identified study against specific inclusion exclusion criteria only eight studies were deemed as relevant for this review. The studies attempt to evaluate different types of data collection interventions including the installation of information communication technology (ICT), improvements to current ICT systems, and how different analysis techniques may be used to monitor performance. The evaluation methods used to measure the costs and benefits of data collection interventions are inconsistent across the identified literature. Overall, the results weakly indicate that collection of hospital data and improvements in data

  9. SSTO vs TSTO design considerations—an assessment of the overall performance, design considerations, technologies, costs, and sensitivities of SSTO and TSTO designs using modern technologies

    Science.gov (United States)

    Penn, Jay P.

    1996-03-01

    It is generally believed by those skilled in launch system design that Single-Stage-To-Orbit (SSTO) designs are more technically challenging, more performance sensitive, and yield larger lift-off weights than do Two-Stage-To-Orbit designs (TSTO's) offering similar payload delivery capability. Without additional insight into the other considerations which drive the development, recurring costs, operability, and reliability of a launch fleet, an analyst may easily conclude that the higher performing, less sensitive TSTO designs, thus yield a better solution to achieving low cost payload delivery. This limited insight could justify an argument to eliminate the X-33 SSTO technology/demonstration development effort, and thus proceed directly to less risky TSTO designs. Insight into real world design considerations of launch vehicles makes the choice of SSTO vs TSTO much less clear. The presentation addresses a more comprehensive evaluation of the general class of SSTO and TSTO concepts. These include pure SSTO's, augmented SSTO's, Siamese Twin, and Pure TSTO designs. The assessment considers vehicle performance and scaling relationships which characterize real vehicle designs. The assessment also addresses technology requirements, operations and supportability, cost implications, and sensitivities. Results of the assessment indicate that the trade space between various SSTO and TSTO design approaches is complex and not yet fully understood. The results of the X-33 technology demonstrators, as well as additional parametric analysis is required to better define the relative performance and costs of the various design approaches. The results also indicate that with modern technologies and today's better understanding of vehicle design considerations, the perception that SSTO's are dramatically heavier and more sensitive than TSTO designs is more of a myth, than reality.

  10. Caffeine ingestion after rapid weight loss in judo athletes reduces perceived effort and increases plasma lactate concentration without improving performance.

    Science.gov (United States)

    Lopes-Silva, Joao P; Felippe, Leandro J C; Silva-Cavalcante, Marcos D; Bertuzzi, Romulo; Lima-Silva, Adriano E

    2014-07-22

    The objective of this study was to examine the effect of caffeine on judo performance, perceived exertion, and plasma lactate response when ingested during recovery from a 5-day weight loss period. Six judokas performed two cycles of a 5-day rapid weight loss procedure to reduce their body weight by ~5%. After weigh-in, subjects re-fed and rehydrated over a 4-h recovery period. In the third hour of this "loading period", subjects ingested a capsule containing either caffeine (6 mg·kg-1) or placebo. One hour later, participants performed three bouts of a judo fitness test with 5-min recovery periods. Perceived exertion and plasma lactate were measured before and immediately after each test bout. Body weight was reduced in both caffeine and placebo conditions after the weight loss period (-3.9% ± 1.6% and -4.0% ± 2.3% from control, respectively, p caffeine or placebo groups. However, plasma lactate was systemically higher and perceived exertion lower in the subjects who ingested caffeine compared to either the control or placebo subjects (p caffeine did not improve performance during the judo fitness test after a 5-day weight loss period, but reduced perceived exertion and increased plasma lactate.

  11. The impact of weighted basketball balls in improving certain physical performances via wheelchair basketball players

    OpenAIRE

    Benzidane, Houcine; Mokrani, Djamel; Zerf, Mohammed

    2018-01-01

    The research aims to determine the effect of a weighted basketball balls training program on some physical performance via wheelchair basketball players. The sample was selected in an intended manner including 20 players’. Divided into two equal groups (experimental 10 players, control 10 players) for the sports season 2016/2017. As protocol experimental, our training program for the experimental group was applied under researchers’ supervision, using Weighted basketball balls in the opposite...

  12. Long-term weight gain and economic impact in pigs castrated under local anaesthesia

    Directory of Open Access Journals (Sweden)

    F.G. Telles

    2016-12-01

    Full Text Available Castration is a controversial practice in swine production because in some countries is still performed without anaesthesia, and therefore causes intense suffering and stress to animals. This study investigated the effect of pre-surgical administration of local anaesthesia (LA on the growth performance of piglets until the end of the growth phase (102 days. Piglets aged 3 to 5 days were selected in pairs of similar weights and same age. They were originated from 22 litters. The groups were randomly assigned to one of two treatments. Castration was performed with (LA; n = 45 or without (NLA; n = 45 intra-testicular administration of 0.5 mL of 2% lidocaine plus adrenaline per testicle, administered by an automatic repeating vaccinator. Castration was performed 10 min later. Average daily weight gain and economic impact were evaluated between the intervals before castration until 21 (weaning phase, before castration until 60 (end of the initial nursery phase and before castration until 102 (growth phase days of age. Average daily weight gain data were analyzed by comparing the average daily weight gain between the weaning phase, 60 and 102 days of age versus the initial weight (pre-castration. At the end of the growing phase, animals treated with LA showed greater weight gain than animals castrated without anaesthesia. LA also showed improved cost:benefit ratio and theore might provide greater economic benefit under the conditions used in this study. Our findings have proved that castration with LA improves long-term weight gain of piglets.

  13. The effects of regional insolation differences upon advanced solar thermal electric power plant performance and energy costs

    Science.gov (United States)

    Latta, A. F.; Bowyer, J. M.; Fujita, T.

    1979-01-01

    This paper presents the performance and cost of four 10-MWe advanced solar thermal electric power plants sited in various regions of the continental United States. Each region has different insolation characteristics which result in varying collector field areas, plant performance, capital costs, and energy costs. The paraboloidal dish, central receiver, cylindrical parabolic trough, and compound parabolic concentrator (CPC) comprise the advanced concepts studied. This paper contains a discussion of the regional insolation data base, a description of the solar systems' performances and costs, and a presentation of a range for the forecast cost of conventional electricity by region and nationally over the next several decades.

  14. ASCR{trademark}: lower NOx removal costs without sacrificing performance

    Energy Technology Data Exchange (ETDEWEB)

    Bible, S.; Rummenhohl, V.; Siebeking, M.; Thomas, R.; Triece, C. [Fuel Tech (United States)

    2011-05-15

    With recent regulatory initiatives, the new Industrial Emissions Directive in Europe, and new rules being proposed by EPA in the USA, the question for power plants is now whether they will be required to reduce NOx emissions in the future to stay in operation, but when. What is needed is a low-capital-cost but high-performance NOx removal technology. 7 figs.

  15. Testing the Feasibility of a Low-Cost Network Performance Measurement Infrastructure

    Energy Technology Data Exchange (ETDEWEB)

    Chevalier, Scott [Indiana Univ., Bloomington, IN (United States). International Networks; Schopf, Jennifer M. [Indiana Univ., Bloomington, IN (United States). International Networks; Miller, Kenneth [Pennsylvania State Univ., University Park, PA (United States). Telecommunications and Networking Services; Zurawski, Jason [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Energy Sciences Network

    2016-07-01

    Todays science collaborations depend on reliable, high performance networks, but monitoring the end-to-end performance of a network can be costly and difficult. The most accurate approaches involve using measurement equipment in many locations, which can be both expensive and difficult to manage due to immobile or complicated assets. The perfSONAR framework facilitates network measurement making management of the tests more reasonable. Traditional deployments have used over-provisioned servers, which can be expensive to deploy and maintain. As scientific network uses proliferate, there is a desire to instrument more facets of a network to better understand trends. This work explores low cost alternatives to assist with network measurement. Benefits include the ability to deploy more resources quickly, and reduced capital and operating expenditures. Finally, we present candidate platforms and a testing scenario that evaluated the relative merits of four types of small form factor equipment to deliver accurate performance measurements.

  16. Suppression of Noise to Obtain a High-Performance Low-Cost Optical Encoder

    Directory of Open Access Journals (Sweden)

    Sergio Alvarez-Rodríguez

    2018-01-01

    Full Text Available Currently, commercial encoders endowed with high precision are expensive sensors, and optical low-cost designs to measure the positioning angle have undesirable levels of system noise which reduce the good performance of devices. This research is devoted to the designing of mathematical filters to suppress noise in polarized transducers, in order to obtain high accuracy, precision, and resolution, along with an adaptive maximum response speed for low-cost optical encoders. This design was proved through a prototype inside a research platform, and experimental results show an accuracy of 3.9, a precision of 26, and a resolution of 17 [arc seconds], at least for the specified working conditions, for the sensing of the angular position of a rotary polarizer. From this work has been obtained a high-performance low-cost polyphase optical encoder, which uses filtering mathematical principles potentially generalizable to other inventions.

  17. Computerized cost estimation spreadsheet and cost data base for fusion devices

    International Nuclear Information System (INIS)

    Hamilton, W.R.; Rothe, K.E.

    1985-01-01

    Component design parameters (weight, surface area, etc.) and cost factors are input and direct and indirect costs are calculated. The cost data base file derived from actual cost experience within the fusion community and refined to be compatible with the spreadsheet costing approach is a catalog of cost coefficients, algorithms, and component costs arranged into data modules corresponding to specific components and/or subsystems. Each data module contains engineering, equipment, and installation labor cost data for different configurations and types of the specific component or subsystem. This paper describes the assumptions, definitions, methodology, and architecture incorporated in the development of the cost estimation spreadsheet and cost data base, along with the type of input required and the output format

  18. Effects of genotype and population density on growth performance, carcass characteristics, and cost-benefits of broiler chickens in north central Nigeria.

    Science.gov (United States)

    Yakubu, Abdulmojeed; Ayoade, John A; Dahiru, Yakubu M

    2010-04-01

    The influence of genotype and stocking densities on growth performance, carcass qualities, and cost-benefits of broilers were examined in a 28-day trial. Two hundred and seven 4-week-old birds each of Anak Titan and Arbor Acre hybrid broiler types were randomly assigned to three stocking density treatments of 8.3, 11.1, and 14.3 birds/m(2) in a 2 x 3 factorial arrangement. Final body weight, average weekly body weight and average weekly feed intake were affected (P Arbor Acres. However, average weekly body weight gain and feed conversion ratio were similar (P > 0.05) in both genetic groups. The effect of placement density on some growth parameters did not follow a linear trend. Arbor Acres had significantly (P 0.05) influenced by genotype and housing density. The economic analysis revealed that higher gross margin was recorded for Arbor Acres compared to Anak Titans (euro 2.76 versus euro 2.19; P 0.05) on profit margin. Genotype x stocking density interaction effect was significant for some of the carcass indices investigated. It is concluded that under sub-humid conditions of a tropical environment, the use of Arbor Acre genetic type as well as a placement density of 14.3 birds/m(2) appeared to be more profitable.

  19. Electrification Futures Study: End-Use Electric Technology Cost and Performance Projections through 2050

    Energy Technology Data Exchange (ETDEWEB)

    Vimmerstedt, Laura J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jadun, Paige [National Renewable Energy Lab. (NREL), Golden, CO (United States); McMillan, Colin A. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Steinberg, Daniel C. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Muratori, Matteo [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mai, Trieu T. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2018-01-02

    This report provides projected cost and performance assumptions for electric technologies considered in the Electrification Futures Study, a detailed and comprehensive analysis of the effects of widespread electrification of end-use service demands in all major economic sectors - transportation, residential and commercial buildings, and industry - for the contiguous United States through 2050. Using extensive literature searches and expert assessment, the authors identify slow, moderate, and rapid technology advancement sensitivities on technology cost and performance, and they offer a comparative analysis of levelized cost metrics as a reference indicator of total costs. The identification and characterization of these end-use service demand technologies is fundamental to the Electrification Futures Study. This report, the larger Electrification Futures Study, and the associated data and methodologies may be useful to planners and analysts in evaluating the potential role of electrification in an uncertain future. The report could be broadly applicable for other analysts and researchers who wish to assess electrification and electric technologies.

  20. Strategic design of cost savings guarantee in energy performance contracting under uncertainty

    International Nuclear Information System (INIS)

    Deng, Qianli; Jiang, Xianglin; Cui, Qingbin; Zhang, Limao

    2015-01-01

    Highlights: • A methodology is proposed to assist Energy Service Companies to maintain competitiveness in winning bids. • Uncertainties within the energy cost savings are modeled stochastically using the Monte-Carlo simulation. • A strategic energy savings guarantee design curve is derived, where all points return as appropriate guarantees. • A campus case is presented to demonstrate the applicability for finding appropriate guaranteed savings value. - Abstract: Among the key barriers to profit in Energy Performance Contracting (EPC) are uncertainties about attaining the realized energy cost savings and potential disputes over the guaranteed cost savings. In this paper, a methodology has been proposed to assist the Energy Service Company (ESCO): (1) to evaluate the risk threshold if the guarantee has already been made, and (2) to determine the guarantee design, if the guarantee has not been made yet, that not only promises the ESCO’s profitability from EPC but also maintains its competitiveness to win the bid. Uncertainties within the energy cost savings are modeled stochastically using Monte-Carlo simulation, taking both the energy price fluctuation and the facility performance variability into account. Based on that, a strategic energy savings guarantee design curve is derived, that all the points on it would return as appropriate guarantees. Finally, a campus case is presented to demonstrate the applicability for finding the appropriate guaranteed savings value. This method is also worth popularizing in similar performance-based projects

  1. Genetic relationships between carcass cut weights predicted from video image analysis and other performance traits in cattle.

    Science.gov (United States)

    Pabiou, T; Fikse, W F; Amer, P R; Cromie, A R; Näsholm, A; Berry, D P

    2012-09-01

    The objective of this study was to quantify the genetic associations between a range of carcass-related traits including wholesale cut weights predicted from video image analysis (VIA) technology, and a range of pre-slaughter performance traits in commercial Irish cattle. Predicted carcass cut weights comprised of cut weights based on retail value: lower value cuts (LVC), medium value cuts (MVC), high value cuts (HVC) and very high value cuts (VHVC), as well as total meat, fat and bone weights. Four main sources of data were used in the genetic analyses: price data of live animals collected from livestock auctions, live-weight data and linear type collected from both commercial and pedigree farms as well as from livestock auctions and weanling quality recorded on-farm. Heritability of carcass cut weights ranged from 0.21 to 0.39. Genetic correlations between the cut traits and the other performance traits were estimated using a series of bivariate sire linear mixed models where carcass cut weights were phenotypically adjusted to a constant carcass weight. Strongest positive genetic correlations were obtained between predicted carcass cut weights and carcass value (min r g(MVC) = 0.35; max r(g(VHVC)) = 0.69), and animal price at both weaning (min r(g(MVC)) = 0.37; max r(g(VHVC)) = 0.66) and post weaning (min r(g(MVC)) = 0.50; max r(g(VHVC)) = 0.67). Moderate genetic correlations were obtained between carcass cut weights and calf price (min r g(HVC) = 0.34; max r g(LVC) = 0.45), weanling quality (min r(g(MVC)) = 0.12; max r (g(VHVC)) = 0.49), linear scores for muscularity at both weaning (hindquarter development: min r(g(MVC)) = -0.06; max r(g(VHVC)) = 0.46), post weaning (hindquarter development: min r(g(MVC)) = 0.23; max r(g(VHVC)) = 0.44). The genetic correlations between total meat weight were consistent with those observed with the predicted wholesale cut weights. Total fat and total bone weights were generally negatively correlated with carcass value, auction

  2. The Economic Impact of Weight Regain

    OpenAIRE

    Sheppard, Caroline E.; Lester, Erica L. W.; Chuck, Anderson W.; Birch, Daniel W.; Karmali, Shahzeer; de Gara, Christopher J.

    2013-01-01

    Background. Obesity is well known for being associated with significant economic repercussions. Bariatric surgery is the only evidence-based solution to this problem as well as a cost-effective method of addressing the concern. Numerous authors have calculated the cost effectiveness and cost savings of bariatric surgery; however, to date the economic impact of weight regain as a component of overall cost has not been addressed. Methods. The literature search was conducted to elucidate the dir...

  3. Physico-mathematical model of motor vehicle of divided weight with unifying energetic element

    Directory of Open Access Journals (Sweden)

    Leonid M. Petrov

    2015-12-01

    Full Text Available The traction characteristics are important for ensuring of motor vehicle work process. In providing the traction characteristics the average velocity of mobile energetic transport grows, energy costs for work process execution are uprating and operation costs are reducing. The implementation of traction characteristics is performed by transmission of mobile energetic transport. Aim: The aim of the work is improvement of torque transfer technology from the engine to the wheel driving forces through the establishment of new construction of divided weight vehicle transmission. Materials and Methods: Consider a motor vehicle of divided weight with unifying energetic element which performs rotary motions relative to the vehicle frame. Results: It was shown that, the momentum which creates the rotational motion depends on the module and the direction of rotation speed of the unifying energetic element. For the first time, the technology and design of vehicle transmission which differs from previous designs by significant simplifying of the torque transmission from the engine to driving wheels at increased value of efficiency coefficient were proposed.

  4. 16 CFR Appendix I to Part 305 - Heating Performance and Cost for Central Air Conditioners

    Science.gov (United States)

    2010-01-01

    ... RULEâ) Pt. 305, App. I Appendix I to Part 305—Heating Performance and Cost for Central Air Conditioners... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Heating Performance and Cost for Central Air Conditioners I Appendix I to Part 305 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER SPECIFIC...

  5. Decidability and Expressiveness of Recursive Weighted Logic

    DEFF Research Database (Denmark)

    Xue, Bingtian; Larsen, Kim Guldstrand; Mardare, Radu Iulian

    2014-01-01

    Labelled weighted transition systems (LWSs) are transition systems labelled with actions and real numbers. The numbers represent the costs of the corresponding actions in terms of resources. RecursiveWeighted Logic (RWL) is a multimodal logic that expresses qualitative and quantitative properties...

  6. An economic cost analysis of emergency department key performance indicators in Ireland.

    Science.gov (United States)

    Gannon, Brenda; Jones, Cheryl; McCabe, Aileen; O'Sullivan, Ronan; Wakai, Abel

    2017-06-01

    High quality data is fundamental to using key performance indicators (KPIs) for performance monitoring. However, the resources required to collect high quality data are often significant and should usually be targeted at high priority areas. As part of a study of 11 emergency department (ED) KPIs in Ireland, the primary objective of this study was to estimate the relative cost of collecting the additional minimum data set (MDS) elements for those 11 KPIs. An economic cost analysis focused on 12 EDs in the Republic of Ireland. The resource use data were obtained using two separate focus group interviews. The number of available MDS elements was obtained from a sample of 100 patient records per KPI per participating ED. Unit costs for all resource use were taken at the midpoint of the relevant staff salary scales. An ED would need to spend an estimated additional &OV0556;3561 per month on average to capture all the MDS elements relevant to the 11 KPIs investigated. The additional cost ranges from 14.8 to 39.2%; this range is 13.9-32.3% for small EDs, whereas the range for medium EDs is 11.7-40%. Regional EDs have a higher additional estimated cost to capture all the relevant MDS elements (&OV0556;3907), compared with urban EDs (&OV0556;3353). The additional cost of data collection, contingent on that already collected, required to capture all the relevant MDS elements for the KPIs examined, ranges from 14.8 to 39.2% per KPI, with variation identified between regional and urban hospitals.

  7. Planar junctionless phototransistor: A potential high-performance and low-cost device for optical-communications

    Science.gov (United States)

    Ferhati, H.; Djeffal, F.

    2017-12-01

    In this paper, a new junctionless optical controlled field effect transistor (JL-OCFET) and its comprehensive theoretical model is proposed to achieve high optical performance and low cost fabrication process. Exhaustive study of the device characteristics and comparison between the proposed junctionless design and the conventional inversion mode structure (IM-OCFET) for similar dimensions are performed. Our investigation reveals that the proposed design exhibits an outstanding capability to be an alternative to the IM-OCFET due to the high performance and the weak signal detection benefit offered by this design. Moreover, the developed analytical expressions are exploited to formulate the objective functions to optimize the device performance using Genetic Algorithms (GAs) approach. The optimized JL-OCFET not only demonstrates good performance in terms of derived drain current and responsivity, but also exhibits superior signal to noise ratio, low power consumption, high-sensitivity, high ION/IOFF ratio and high-detectivity as compared to the conventional IM-OCFET counterpart. These characteristics make the optimized JL-OCFET potentially suitable for developing low cost and ultrasensitive photodetectors for high-performance and low cost inter-chips data communication applications.

  8. Adolescent Weight Status and Self-Reported School Performance in South Korea

    Directory of Open Access Journals (Sweden)

    Young Kyung Do

    2011-01-01

    Full Text Available Using a nationally representative sample of 142 783 middle school (13–15 years old and high school (16–18 years old students in South Korea, this study examined whether (1 overweight and obesity are more likely to be associated with lower self-reported school performance; (2 overweight and obese students are more likely to enrol in a vocational high school as opposed to a general high school; (3 the association between obesity and poorer self-reported school performance is mediated through body image stress and health status. We found that excess weight was negatively associated with self-reported school performance among middle and general high school students, and that obese students had a higher probability of being enrolled in a vocational over a general high school. We did not find strong evidence on the mediating role of body image stress and health status.

  9. 16 CFR Appendix H to Part 305 - Cooling Performance and Cost for Central Air Conditioners

    Science.gov (United States)

    2010-01-01

    ... RULEâ) Pt. 305, App. H Appendix H to Part 305—Cooling Performance and Cost for Central Air Conditioners... Split System Units Central Air Conditioners (Cooling Only): All capacities 10.9 23.0 Heat Pumps (Cooling... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Cooling Performance and Cost for Central Air...

  10. On the Performance of Linear Decreasing Inertia Weight Particle Swarm Optimization for Global Optimization

    Science.gov (United States)

    Arasomwan, Martins Akugbe; Adewumi, Aderemi Oluyinka

    2013-01-01

    Linear decreasing inertia weight (LDIW) strategy was introduced to improve on the performance of the original particle swarm optimization (PSO). However, linear decreasing inertia weight PSO (LDIW-PSO) algorithm is known to have the shortcoming of premature convergence in solving complex (multipeak) optimization problems due to lack of enough momentum for particles to do exploitation as the algorithm approaches its terminal point. Researchers have tried to address this shortcoming by modifying LDIW-PSO or proposing new PSO variants. Some of these variants have been claimed to outperform LDIW-PSO. The major goal of this paper is to experimentally establish the fact that LDIW-PSO is very much efficient if its parameters are properly set. First, an experiment was conducted to acquire a percentage value of the search space limits to compute the particle velocity limits in LDIW-PSO based on commonly used benchmark global optimization problems. Second, using the experimentally obtained values, five well-known benchmark optimization problems were used to show the outstanding performance of LDIW-PSO over some of its competitors which have in the past claimed superiority over it. Two other recent PSO variants with different inertia weight strategies were also compared with LDIW-PSO with the latter outperforming both in the simulation experiments conducted. PMID:24324383

  11. Comparison of Cloud backup performance and costs in Oracle database

    OpenAIRE

    Aljaž Zrnec; Dejan Lavbič

    2011-01-01

    Current practice of backing up data is based on using backup tapes and remote locations for storing data. Nowadays, with the advent of cloud computing a new concept of database backup emerges. The paper presents the possibility of making backup copies of data in the cloud. We are mainly focused on performance and economic issues of making backups in the cloud in comparison to traditional backups. We tested the performance and overall costs of making backup copies of data in Oracle database u...

  12. Weight-Aware Sensor Deployment in Wireless Sensor Networks for Smart Cities

    Directory of Open Access Journals (Sweden)

    Mingshan Xie

    2018-01-01

    Full Text Available During the construction of wireless sensor networks (WSNs for smart cities, a preliminary survey of the relative criticalness within the monitored area can be performed. It is a challenge for deterministic sensor deployment to balance the tradeoff of sensing reliability and cost. In this paper, based on the sensing accuracy of the sensor, we establish a reliability model of the sensing area which is divided into sensing grids, and different weights are allocated to those grids. We employ a practical evaluation criterion using seesaw mapping for determining the weights of sensing grids. We further formulate and solve an optimization problem for maximizing the trust degree of the WSNs. With our proposed method, the efficient deployment of sensors can be realized. Simulation results show that our proposed deployment strategy can achieve higher trust degree with reduced sensor deployment cost and lower number of sensors at a certain miss probability threshold.

  13. Performance and cost benefits associated with nonimaging secondary concentrators used in point-focus dish solar thermal applications

    Science.gov (United States)

    Ogallagher, J.; Winston, R.

    1987-09-01

    Using nonimaging secondary concentrators in point-focus applications may permit the development of more cost-effective concentrator systems by either improving performance or reducing costs. Secondaries may also increase design flexibility. The major objective of this study was to develop as complete an understanding as possible of the quantitative performance and cost effects associated with deploying nonimaging secondary concentrators at the focal zone of point-focus solar thermal concentrators. A performance model was developed that uses a Monte Carlo ray-trace procedure to determine the focal plane distribution of a paraboloidal primary as a function of optical parameters. It then calculates the corresponding optimized concentration and thermal efficiency as a function of temperature with and without the secondary. To examine the potential cost benefits associated with secondaries, a preliminary model for the rational optimization of performance versus cost trade-offs was developed. This model suggests a possible 10 to 20 percent reduction in the cost of delivered energy when secondaries are used. This is a lower limit, and the benefits may even be greater if using a secondary permits the development of inexpensive primary technologies for which the performance would not otherwise be viable.

  14. Weighted divergence correction scheme and its fast implementation

    Science.gov (United States)

    Wang, ChengYue; Gao, Qi; Wei, RunJie; Li, Tian; Wang, JinJun

    2017-05-01

    Forcing the experimental volumetric velocity fields to satisfy mass conversation principles has been proved beneficial for improving the quality of measured data. A number of correction methods including the divergence correction scheme (DCS) have been proposed to remove divergence errors from measurement velocity fields. For tomographic particle image velocimetry (TPIV) data, the measurement uncertainty for the velocity component along the light thickness direction is typically much larger than for the other two components. Such biased measurement errors would weaken the performance of traditional correction methods. The paper proposes a variant for the existing DCS by adding weighting coefficients to the three velocity components, named as the weighting DCS (WDCS). The generalized cross validation (GCV) method is employed to choose the suitable weighting coefficients. A fast algorithm for DCS or WDCS is developed, making the correction process significantly low-cost to implement. WDCS has strong advantages when correcting velocity components with biased noise levels. Numerical tests validate the accuracy and efficiency of the fast algorithm, the effectiveness of GCV method, and the advantages of WDCS. Lastly, DCS and WDCS are employed to process experimental velocity fields from the TPIV measurement of a turbulent boundary layer. This shows that WDCS achieves a better performance than DCS in improving some flow statistics.

  15. A Study of a Load Cell Based High Speed Weighting Method for a Potato Sorter

    International Nuclear Information System (INIS)

    Yang, Jong Hoon

    2002-02-01

    Potatoes, together with tangerines, are one of the major agricultural products in Jeju, and the production account for more than 30 % of the domestic production. Recently some kinds of sorting machine for potatoes are available, but they are not extensively used because their performance is not satisfactory and/or they are very expensive. This paper presents a load cell based high speed weighting method for sorting the potatoes. This method is based on the fact that the linear momentum of a potato is proportional to the mass of it. To test the performance of the weighting system, we developed load cell based automatic sorting system for potatoes. The system does not adopt an additional mechanism for weighting the potato such as a cup conveyer. It uses normal flat conveyers themselves so that the cost for maintenance and establishment will be lower than other system. Through sets of experiments, the developed weighting system was proved to be very reliable, and its performance is good enough to use as a practical sorting system

  16. Caffeine Ingestion after Rapid Weight Loss in Judo Athletes Reduces Perceived Effort and Increases Plasma Lactate Concentration without Improving Performance

    Directory of Open Access Journals (Sweden)

    Joao P. Lopes-Silva

    2014-07-01

    Full Text Available The objective of this study was to examine the effect of caffeine on judo performance, perceived exertion, and plasma lactate response when ingested during recovery from a 5-day weight loss period. Six judokas performed two cycles of a 5-day rapid weight loss procedure to reduce their body weight by ~5%. After weigh-in, subjects re-fed and rehydrated over a 4-h recovery period. In the third hour of this “loading period”, subjects ingested a capsule containing either caffeine (6 mg·kg−1 or placebo. One hour later, participants performed three bouts of a judo fitness test with 5-min recovery periods. Perceived exertion and plasma lactate were measured before and immediately after each test bout. Body weight was reduced in both caffeine and placebo conditions after the weight loss period (−3.9% ± 1.6% and −4.0% ± 2.3% from control, respectively, p < 0.05. At three hours after weigh-in, body weight had increased with both treatments but remained below the control (−3.0% ± 1.3% and −2.7% ± 2.2%. There were no significant differences in the number of throws between the control, caffeine or placebo groups. However, plasma lactate was systemically higher and perceived exertion lower in the subjects who ingested caffeine compared to either the control or placebo subjects (p < 0.05. In conclusion, caffeine did not improve performance during the judo fitness test after a 5-day weight loss period, but reduced perceived exertion and increased plasma lactate.

  17. Avoidable waste management costs

    International Nuclear Information System (INIS)

    Hsu, K.; Burns, M.; Priebe, S.; Robinson, P.

    1995-01-01

    This report describes the activity based costing method used to acquire variable (volume dependent or avoidable) waste management cost data for routine operations at Department of Energy (DOE) facilities. Waste volumes from environmental restoration, facility stabilization activities, and legacy waste were specifically excluded from this effort. A core team consisting of Idaho National Engineering Laboratory, Los Alamos National Laboratory, Rocky Flats Environmental Technology Site, and Oak Ridge Reservation developed and piloted the methodology, which can be used to determine avoidable waste management costs. The method developed to gather information was based on activity based costing, which is a common industrial engineering technique. Sites submitted separate flow diagrams that showed the progression of work from activity to activity for each waste type or treatability group. Each activity on a flow diagram was described in a narrative, which detailed the scope of the activity. Labor and material costs based on a unit quantity of waste being processed were then summed to generate a total cost for that flow diagram. Cross-complex values were calculated by determining a weighted average for each waste type or treatability group based on the volume generated. This study will provide DOE and contractors with a better understanding of waste management processes and their associated costs. Other potential benefits include providing cost data for sites to perform consistent cost/benefit analysis of waste minimization and pollution prevention (WMIN/PP) options identified during pollution prevention opportunity assessments and providing a means for prioritizing and allocating limited resources for WMIN/PP

  18. Avoidable waste management costs

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, K.; Burns, M.; Priebe, S.; Robinson, P.

    1995-01-01

    This report describes the activity based costing method used to acquire variable (volume dependent or avoidable) waste management cost data for routine operations at Department of Energy (DOE) facilities. Waste volumes from environmental restoration, facility stabilization activities, and legacy waste were specifically excluded from this effort. A core team consisting of Idaho National Engineering Laboratory, Los Alamos National Laboratory, Rocky Flats Environmental Technology Site, and Oak Ridge Reservation developed and piloted the methodology, which can be used to determine avoidable waste management costs. The method developed to gather information was based on activity based costing, which is a common industrial engineering technique. Sites submitted separate flow diagrams that showed the progression of work from activity to activity for each waste type or treatability group. Each activity on a flow diagram was described in a narrative, which detailed the scope of the activity. Labor and material costs based on a unit quantity of waste being processed were then summed to generate a total cost for that flow diagram. Cross-complex values were calculated by determining a weighted average for each waste type or treatability group based on the volume generated. This study will provide DOE and contractors with a better understanding of waste management processes and their associated costs. Other potential benefits include providing cost data for sites to perform consistent cost/benefit analysis of waste minimization and pollution prevention (WMIN/PP) options identified during pollution prevention opportunity assessments and providing a means for prioritizing and allocating limited resources for WMIN/PP.

  19. Comparison of predictive performance of data mining algorithms in predicting body weight in Mengali rams of Pakistan

    Directory of Open Access Journals (Sweden)

    Senol Celik

    Full Text Available ABSTRACT The present study aimed at comparing predictive performance of some data mining algorithms (CART, CHAID, Exhaustive CHAID, MARS, MLP, and RBF in biometrical data of Mengali rams. To compare the predictive capability of the algorithms, the biometrical data regarding body (body length, withers height, and heart girth and testicular (testicular length, scrotal length, and scrotal circumference measurements of Mengali rams in predicting live body weight were evaluated by most goodness of fit criteria. In addition, age was considered as a continuous independent variable. In this context, MARS data mining algorithm was used for the first time to predict body weight in two forms, without (MARS_1 and with interaction (MARS_2 terms. The superiority order in the predictive accuracy of the algorithms was found as CART > CHAID ≈ Exhaustive CHAID > MARS_2 > MARS_1 > RBF > MLP. Moreover, all tested algorithms provided a strong predictive accuracy for estimating body weight. However, MARS is the only algorithm that generated a prediction equation for body weight. Therefore, it is hoped that the available results might present a valuable contribution in terms of predicting body weight and describing the relationship between the body weight and body and testicular measurements in revealing breed standards and the conservation of indigenous gene sources for Mengali sheep breeding. Therefore, it will be possible to perform more profitable and productive sheep production. Use of data mining algorithms is useful for revealing the relationship between body weight and testicular traits in describing breed standards of Mengali sheep.

  20. Net Shape Spin Formed Cryogenic Aluminum Lithium Cryogenic Tank Domes for Lower Cost Higher Performance Launch Vehicles

    Science.gov (United States)

    Curreri, Peter A.; Hoffman, Eric; Domack, Marcia; Brewster, Jeb; Russell, Carolyn

    2013-01-01

    With the goal of lower cost (simplified manufacturing and lower part count) and higher performance (higher strength to weight alloys) the NASA Technical Maturation Program in 2006 funded a proposal to investigate spin forming of space launch vehicle cryogenic tank domes. The project funding continued under the NASA Exploration Technology Development Program through completion in FY12. The first phase of the project involved spin forming of eight, 1 meter diameter "path finder" domes. Half of these were processed using a concave spin form process (MT Aerospace, Augsburg Germany) and the other half using a convex process (Spincraft, Boston MA). The convex process has been used to produce the Ares Common Bulkhead and the concave process has been used to produce dome caps for the Space Shuttle light weight external tank and domes for the NASDA H2. Aluminum Lithium material was chosen because of its higher strength to weight ratio than the Aluminum 2219 baseline. Aluminum lithium, in order to obtain the desired temper (T8), requires a cold stretch after the solution heat treatment and quench. This requirement favors the concave spin form process which was selected for scale up. This paper describes the results of processing four, 5.5 meter diameter (upper stage scale) net shaped spin formed Aluminum Lithium domes. In order to allow scalability beyond the limits of foundry and rolling mills (about 12 foot width) the circular blank contained one friction stir weld (heavy lifter scales require a flat blank containing two welds). Mechanical properties data (tensile, fracture toughness, stress corrosion, and simulated service testing) for the parent metal and weld will also be discussed.

  1. Design windows and cost analysis on helical reactors

    International Nuclear Information System (INIS)

    Kozaki, Y.; Imagawa, S.; Sagara, A.

    2007-01-01

    The LHD type helical reactors are characterized by a large major radius but slender helical coil, which give us different approaches for power plants from tokamak reactors. For searching design windows of helical reactors and discussing their potential as power plants, we have developed a mass-cost estimating model linked with system design code (HeliCos), thorough studying the relationships between major plasma parameters and reactor parameters, and weight of major components. In regard to cost data we have much experience through preparing ITER construction. To compare the weight and cost of magnet systems between tokamak and helical reactors, we broke down magnet systems and cost factors, such as weights of super conducting strands, conduits, support structures, and winding unit costs, through estimating ITER cost data basis. Based on FFHR2m1 deign we considered a typical 3 GWth helical plant (LHD type) with the same magnet size, coil major radius Rc 14 m, magnetic energy 120 GJ, but increasing plasma densities. We evaluated the weight and cost of magnet systems of 3 GWth helical plant, the total magnet weights of 16,000ton and costs of 210 BYen, which are similar values of tokamak reactors (10,200 ton, 110 BYen in ITER 2002 report, and 21,900 ton, 275 BYen in ITER FDR1999). The costs of strands and winding occupy 70% of total magnet costs, and influence entire power plants economics. The design windows analysis and comparative economics studies to optimize the main reactor parameters have been carried out. Economics studies show that it is misunderstanding to consider helical coils are too large and too expensive to achieve power plants. But we should notice that the helical reactor design windows and economics are very sensitive to allowable blanket space (depend on ergodic layer conditions) and diverter configuration for decreasing heat loads. (orig.)

  2. Development of MY-DRG casemix pharmacy service weights in UKM Medical Centre in Malaysia.

    Science.gov (United States)

    Ali Jadoo, Saad Ahmed; Aljunid, Syed Mohamed; Nur, Amrizal Muhammad; Ahmed, Zafar; Van Dort, Dexter

    2015-02-10

    The service weight is among several issues and challenges in the implementation of case-mix in developing countries, including Malaysia. The aim of this study is to develop the Malaysian Diagnosis Related Group (MY-DRG) case-mix pharmacy service weight in University Kebangsaan Malaysia-Medical Center (UKMMC) by identifying the actual cost of pharmacy services by MY-DRG groups in the hospital. All patients admitted to UKMMC in 2011 were recruited in this study. Combination of Step-down and Bottom-up costing methodology has been used in this study. The drug and supplies cost; the cost of staff; the overhead cost; and the equipment cost make up the four components of pharmacy. Direct costing approach has been employed to calculate Drugs and supplies cost from electronic-prescription system; and the inpatient pharmacy staff cost, while the overhead cost and the pharmacy equipments cost have been calculated indirectly from MY-DRG data base. The total pharmacy cost was obtained by summing the four pharmacy components' cost per each MY-DRG. The Pharmacy service weight of a MY-DRG was estimated by dividing the average pharmacy cost of the investigated MY-DRG on the average of a specified MY-DRG (which usually the average pharmacy cost of all MY-DRGs). Drugs and supplies were the main component (86.0%) of pharmacy cost compared o overhead cost centers (7.3%), staff cost (6.5%) and pharmacy equipments (0.2%) respectively. Out of 789 inpatient MY-DRGs case-mix groups, 450 (57.0%) groups were utilized by the UKMMC. Pharmacy service weight has been calculated for each of these 450 MY-DRGs groups. MY-DRG case-mix group of Lymphoma & Chronic Leukemia group with severity level three (C-4-11-III) has the highest pharmacy service weight of 11.8 equivalents to average pharmacy cost of RM 5383.90. While the MY-DRG case-mix group for Circumcision with severity level one (V-1-15-I) has the lowest pharmacy service weight of 0.04 equivalents to average pharmacy cost of RM 17.83. A mixed

  3. Reproductive performance and body weight changes in draught cows in a smallholder semi-arid farming area of Zimbabwe.

    Science.gov (United States)

    Chimonyo, M; Kusina, N T; Hamudikuwanda, H; Nyoni, O

    2000-12-01

    The reproductive performance of 46 cows in a semi-arid, smallholder farming area of Zimbabwe was monitored for a year. Half the cows were used throughout the monitoring period for various draught purposes, including ploughing and procurement of farm produce for marketing using carts. All the cows lost body weight between July and October, after which the cows that were not worked gained weight until June of the following year. In contrast, the cows that were worked continued to lose body weight until January, throughout the time during which they were used to provide draught power, after which they gained weight. Body weights were significantly higher (p draught purposes caused loss of body weight and reduced ovarian activity and conception rates.

  4. Balancing low cost with reliable operation in the rotordynamic design of the ALS Liquid Hydrogen Fuel Turbopump

    Science.gov (United States)

    Greenhill, L. M.

    1990-01-01

    The Air Force/NASA Advanced Launch System (ALS) Liquid Hydrogen Fuel Turbopump (FTP) has primary design goals of low cost and high reliability, with performance and weight having less importance. This approach is atypical compared with other rocket engine turbopump design efforts, such as on the Space Shuttle Main Engine (SSME), which emphasized high performance and low weight. Similar to the SSME turbopumps, the ALS FTP operates supercritically, which implies that stability and bearing loads strongly influence the design. In addition, the use of low cost/high reliability features in the ALS FTP such as hydrostatic bearings, relaxed seal clearances, and unshrouded turbine blades also have a negative influence on rotordynamics. This paper discusses the analysis conducted to achieve a balance between low cost and acceptable rotordynamic behavior, to ensure that the ALS FTP will operate reliably without subsynchronous instabilities or excessive bearing loads.

  5. Direct and indirect relationships of physical fitness, weight status, and learning duration to academic performance in Japanese schoolchildren.

    Science.gov (United States)

    Ishihara, Toru; Morita, Noriteru; Nakajima, Toshihiro; Okita, Koichi; Yamatsu, Koji; Sagawa, Masato

    2018-03-01

    The purpose of this study was to determine, using structural equation modelling (SEM), the direct and indirect influence of daily behaviours (i.e. exercise/learning durations), weight status, and physical fitness on academic performance among seventh-grade schoolchildren, after controlling for socioeconomic status. We analysed cross-sectional data from 274 schoolchildren (159 males and 115 females; 12-13 years old). Academic performance was assessed using the total grade points in eight academic subjects. Physical fitness was evaluated using the total score of eight physical fitness tests and weight status using body mass index. The daily behaviours and socioeconomic status were assessed by the questionnaire. The SEM showed an adequate fit to the data (χ 2  = 0.684, p = .710, RMSEA = .000). Physical fitness and learning durations had direct effects on academic performance (β = .301, p academic performance via physical fitness. These findings suggest that, independent of socioeconomic status and learning durations, exercise habits and maintaining healthy weight status may indirectly contribute to academic success via better physical fitness in children.

  6. The anticipated costs analysis and benefit items survey against performing the maintenance rule

    International Nuclear Information System (INIS)

    Hwang, M. J.; Kim, K. Y.; Yang, Z. A.

    2002-01-01

    In this paper, we surveyed the cost and benefit items and evaluated the costs against performing the Maintenance Rule. In the past, only one electric power company had provided the electricity without free competition in Korea. In these days, however, the electric power company was divided into two parts by the sources: atomic and hydraulic generation and thermal-power generation. Therefore, the generation sources that done have competitiveness at the price will be weeded out in the electric power market. Although the preferential goal is on the safe operation at the Nuclear power Plants (NPPs), if too much money is required to maintain or improve the safety of the NPP, the licensee could hesitate to adopt the program related to the safety even though it is a good one. Since the Risk-Informed Applications (RIA) have been using for a plant operation in recent, the condition of a plant might be changed. Therefore, considering the affects of the RIA, a method to keep the capability through the monitoring the maintenance effectiveness has been proposed. However, to perform this, a number of works, continuous collecting data and monitoring the maintenance effectiveness and understanding the reason of degrading capability, should be preceded. Therefore, a lot of man-hour is needed to develop and to manage the application method, and the licensee should pay the costs. Therefore, in the domestic circumstance, it is necessary to evaluate the cost to monitor the maintenance effectiveness. Hence, we are going to examine the cost to perform the MR and its anticipated benefit lists

  7. French Modular Impoundment: Final Cost and Performance Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Drown, Peter [French Development Enterprises, LLC, North Billerica, MA (United States); French, Bill [French Development Enterprises, LLC, North Billerica, MA (United States)

    2017-05-17

    This report comprises the Final Cost and Performance Report for the Department of Energy Award # EE0007244, the French Modular Impoundment (aka the “French Dam”.) The French Dam is a system of applying precast modular construction to water control structures. The “French Dam” is a term used to cover the construction means/methods used to construct or rehabilitate dams, diversion structures, powerhouses, and other hydraulic structures which impound water and are covered under FDE’s existing IP (Patents # US8414223B2; US9103084B2.)

  8. Processing bulk natural wood into a high-performance structural material

    Science.gov (United States)

    Jianwei Song; Chaoji Chen; Shuze Zhu; Mingwei Zhu; Jiaqi Dai; Upamanyu Ray; Yiju Li; Yudi Kuang; Yongfeng Li; Nelson Quispe; Yonggang Yao; Amy Gong; Ulrich H. Leiste; Hugh A. Bruck; J. Y. Zhu; Azhar Vellore; Heng Li; Marilyn L. Minus; Zheng Jia; Ashlie Martini; Teng Li; Liangbing Hu

    2018-01-01

    Synthetic structural materials with exceptional mechanical performance suffer from either large weight and adverse environmental impact (for example, steels and alloys) or complex manufacturing processes and thus high cost (for example, polymer-based and biomimetic composites)1–8. Natural wood is a low-cost and abundant material and has been used...

  9. Performance and cost benefits analysis of double-pass solar collector with and without fins

    International Nuclear Information System (INIS)

    Fudholi, Ahmad; Sopian, Kamaruzzaman; Ruslan, Mohd Hafidz; Othman, Mohd Yusof

    2013-01-01

    Highlights: • The thermal performances and cost analysis of the double-pass solar collector with and without fins absorber were discussed. • The theoretical and experimental study on the double-pass solar air collector with and without fins absorber was conducted. • The ratio of AC/AEG or the cost benefit ratio was presented. • The double-pass solar collector with fins absorber is more cost-effective compared to without fins absorber. - Abstract: The performance and cost benefit analysis of double-pass solar collector with and without fins have been conducted. The theoretical model using steady state analysis has been developed and compared with the experimental results. The performance curves of the double-pass solar collector with and without fins, which included the effects of mass flow rate and solar intensity on the thermal efficiency of the solar collector, were obtained. Results indicated that the thermal efficiency is proportional to the solar intensity at a specific mass flow rate. The thermal efficiency increased by 9% at a solar intensity of 425–790 W/m 2 and mass flow rate of 0.09 kg/s. The theoretical and experimental analysis showed a similar trend as well as close agreement. Moreover, a cost-effectiveness model has been developed examine the cost benefit ratio of double-pass solar collector with and without fins. Evaluation of the annual cost (AC) and the annual energy gain (AEG) of the collector were also performed. The results show that the double-pass solar collector with fins is more cost-effective compared to the double-pass solar collector without fins for mass flow rate of 0.01–0.07 kg/s. Also, simulations were obtained for the double-pass solar collector with fins at Nusselt number of 5.42–36.21. The energy efficiency of collector increases with the increase of Nusselt number. The results show that by increasing the Nusselt number simultaneously would drop the outlet temperature at any solar intensity. Increase in Nusselt number

  10. Analysis of the Effect of Employee Costs on Company Performance

    Directory of Open Access Journals (Sweden)

    Željko Požega

    2010-07-01

    Full Text Available The goal of every economic entity is to accomplish an optimal system of compensation management and to reach maximum returns through optimal employee investment, raising their motivation and knowledge as well as developing their abilities and skills. In order to reach this goal of maximizing company performance it is necessary to systematically approach the management of human resources within a certain economic entity and to create the fairest material and non-material reward and punishment system by using compensation management methods. This in turn will bring about a positive working atmosphere in the company, where employees will rapidly and easily adjust to changes, interact and co-operate with one another at a high level. This research, which studies the effect of employee costs on company performance, is divided into three chapters. The first chapter provides a brief theoretical overview of the importance of compensation management in human resources administration and reaching business efficiency, i.e. the different possibilities of creating a reward and punishment system in a company which aims to organise an optimal working atmosphere. The second chapter demonstrates the applied methodology and illustrates the information from different companies, which has been used in this research and analysis. The information comprises statistical data of employee costs, income, profits and losses from a sample of companies from the Republic of Croatia in 2008. The third part deals with the analysis and interpretation of the research results which show the effect of employee costs on the income and company performance, also expressed per employee. The goal of this research is to test the hypothesis that companies with higher employee cost, i.e. with higher investment in human resources, on average obtain a higher income and a higher profit per employee and are more efficient and more successful on the market. From the given hypothesis, one can

  11. ALIFE@Work: a randomised controlled trial of a distance counselling lifestyle programme for weight control among an overweight working population [ISRCTN04265725

    Directory of Open Access Journals (Sweden)

    Hendriksen Ingrid JM

    2006-05-01

    Full Text Available Abstract Background The prevalence of overweight is increasing and its consequences will cause a major public health burden in the near future. Cost-effective interventions for weight control among the general population are therefore needed. The ALIFE@Work study is investigating a novel lifestyle intervention, aimed at the working population, with individual counselling through either phone or e-mail. This article describes the design of the study and the participant flow up to and including randomisation. Methods/Design ALIFE@Work is a controlled trial, with randomisation to three arms: a control group, a phone based intervention group and an internet based intervention group. The intervention takes six months and is based on a cognitive behavioural approach, addressing physical activity and diet. It consists of 10 lessons with feedback from a personal counsellor, either by phone or e-mail, between each lesson. Lessons contain educational content combined with behaviour change strategies. Assignments in each lesson teach the participant to apply these strategies to every day life. The study population consists of employees from seven Dutch companies. The most important inclusion criteria are having a body mass index (BMI ≥ 25 kg/m2 and being an employed adult. Primary outcomes of the study are body weight and BMI, diet and physical activity. Other outcomes are: perceived health; empowerment; stage of change and self-efficacy concerning weight control, physical activity and eating habits; work performance/productivity; waist circumference, sum of skin folds, blood pressure, total blood cholesterol level and aerobic fitness. A cost-utility- and a cost-effectiveness analysis will be performed as well. Physiological outcomes are measured at baseline and after six and 24 months. Other outcomes are measured by questionnaire at baseline and after six, 12, 18 and 24 months. Statistical analyses for short term (six month results are performed with

  12. Birth weight ratio as an alternative to birth weight percentile to express infant weight in research and clinical practice: a nationwide cohort study

    NARCIS (Netherlands)

    Voskamp, Bart Jan; Kazemier, Brenda M.; Schuit, Ewoud; Mol, Ben Willem J.; Buimer, Maarten; Pajkrt, Eva; Ganzevoort, Wessel

    2014-01-01

    Objective. To compare birth weight ratio and birth weight percentile to express infant weight when assessing pregnancy outcome. Study Design. We performed a national cohort study. Birth weight ratio was calculated as the observed birth weight divided by the median birth weight for gestational age.

  13. Construction and performance analysis of variable-weight optical orthogonal codes for asynchronous OCDMA systems

    Science.gov (United States)

    Li, Chuan-qi; Yang, Meng-jie; Zhang, Xiu-rong; Chen, Mei-juan; He, Dong-dong; Fan, Qing-bin

    2014-07-01

    A construction scheme of variable-weight optical orthogonal codes (VW-OOCs) for asynchronous optical code division multiple access (OCDMA) system is proposed. According to the actual situation, the code family can be obtained by programming in Matlab with the given code weight and corresponding capacity. The formula of bit error rate (BER) is derived by taking account of the effects of shot noise, avalanche photodiode (APD) bulk, thermal noise and surface leakage currents. The OCDMA system with the VW-OOCs is designed and improved. The study shows that the VW-OOCs have excellent performance of BER. Despite of coming from the same code family or not, the codes with larger weight have lower BER compared with the other codes in the same conditions. By taking simulation, the conclusion is consistent with the analysis of BER in theory. And the ideal eye diagrams are obtained by the optical hard limiter.

  14. Downsizing a database platform for increased performance and decreased costs

    Energy Technology Data Exchange (ETDEWEB)

    Miller, M.M.; Tolendino, L.F.

    1993-06-01

    Technological advances in the world of microcomputers have brought forth affordable systems and powerful software than can compete with the more traditional world of minicomputers. This paper describes an effort at Sandia National Laboratories to decrease operational and maintenance costs and increase performance by moving a database system from a minicomputer to a microcomputer.

  15. Computer programs for capital cost estimation, lifetime economic performance simulation, and computation of cost indexes for laser fusion and other advanced technology facilities

    International Nuclear Information System (INIS)

    Pendergrass, J.H.

    1978-01-01

    Three FORTRAN programs, CAPITAL, VENTURE, and INDEXER, have been developed to automate computations used in assessing the economic viability of proposed or conceptual laser fusion and other advanced-technology facilities, as well as conventional projects. The types of calculations performed by these programs are, respectively, capital cost estimation, lifetime economic performance simulation, and computation of cost indexes. The codes permit these three topics to be addressed with considerable sophistication commensurate with user requirements and available data

  16. Cost and performance analysis of concentrating solar power systems with integrated latent thermal energy storage

    International Nuclear Information System (INIS)

    Nithyanandam, K.; Pitchumani, R.

    2014-01-01

    Integrating TES (thermal energy storage) in a CSP (concentrating solar power) plant allows for continuous operation even during times when solar irradiation is not available, thus providing a reliable output to the grid. In the present study, the cost and performance models of an EPCM-TES (encapsulated phase change material thermal energy storage) system and HP-TES (latent thermal storage system with embedded heat pipes) are integrated with a CSP power tower system model utilizing Rankine and s-CO 2 (supercritical carbon-dioxide) power conversion cycles, to investigate the dynamic TES-integrated plant performance. The influence of design parameters of the storage system on the performance of a 200 MW e capacity power tower CSP plant is studied to establish design envelopes that satisfy the U.S. Department of Energy SunShot Initiative requirements, which include a round-trip annualized exergetic efficiency greater than 95%, storage cost less than $15/kWh t and LCE (levelized cost of electricity) less than 6 ¢/kWh. From the design windows, optimum designs of the storage system based on minimum LCE, maximum exergetic efficiency, and maximum capacity factor are reported and compared with the results of two-tank molten salt storage system. Overall, the study presents the first effort to construct and analyze LTES (latent thermal energy storage) integrated CSP plant performance that can help assess the impact, cost and performance of LTES systems on power generation from molten salt power tower CSP plant. - Highlights: • Presents technoeconomic analysis of thermal energy storage integrated concentrating solar power plants. • Presents a comparison of different storage options. • Presents optimum design of thermal energy storage system for steam Rankine and supercritical carbon dioxide cycles. • Presents designs for maximizing exergetic efficiency while minimizing storage cost and levelized cost of energy

  17. Handling Dynamic Weights in Weighted Frequent Pattern Mining

    Science.gov (United States)

    Ahmed, Chowdhury Farhan; Tanbeer, Syed Khairuzzaman; Jeong, Byeong-Soo; Lee, Young-Koo

    Even though weighted frequent pattern (WFP) mining is more effective than traditional frequent pattern mining because it can consider different semantic significances (weights) of items, existing WFP algorithms assume that each item has a fixed weight. But in real world scenarios, the weight (price or significance) of an item can vary with time. Reflecting these changes in item weight is necessary in several mining applications, such as retail market data analysis and web click stream analysis. In this paper, we introduce the concept of a dynamic weight for each item, and propose an algorithm, DWFPM (dynamic weighted frequent pattern mining), that makes use of this concept. Our algorithm can address situations where the weight (price or significance) of an item varies dynamically. It exploits a pattern growth mining technique to avoid the level-wise candidate set generation-and-test methodology. Furthermore, it requires only one database scan, so it is eligible for use in stream data mining. An extensive performance analysis shows that our algorithm is efficient and scalable for WFP mining using dynamic weights.

  18. Performance characteristics of broilers fed graded levels of Moringa oleifera leaf meal

    Directory of Open Access Journals (Sweden)

    Ayo-Ajasa, O.Y.

    2016-06-01

    Full Text Available Cost of conventional protein sources is on the increase recently; hence, there is the need for cheaper alternative sources that will not compromise the performance characteristics of broiler birds taking into consideration the cost of production. Moringa leaf meal has been reported to increase the performance of broiler birds due to its rich protein content. Two hundred day-old broiler chicks were used to assess the effects of partial replacement of soya bean meal with Moringa (Moringa oleifera leaf meal on broiler chickens in an 8-wk feeding trial. The birds were randomly assigned in equal numbers into five dietary treatments: 0, 5, 10, 15, and 20 % Moringa leaf meal (MOLM. Each treatment was replicated four times with 10 birds per replicate. The results showed that final weight, weight gain, daily weight gain, total feed intake, daily feed intake and feed conversion ratio were significantly (p0.05 effect on primal cut parts and relative organ weight. From the results of this study, replacement of soybean meal with MOLM up to 20% did not have any adverse effect on growth performance and carcass traits of broiler chickens.

  19. Affordable Design: A Methodolgy to Implement Process-Based Manufacturing Cost into the Traditional Performance-Focused Multidisciplinary Design Optimization

    Science.gov (United States)

    Bao, Han P.; Samareh, J. A.

    2000-01-01

    The primary objective of this paper is to demonstrate the use of process-based manufacturing and assembly cost models in a traditional performance-focused multidisciplinary design and optimization process. The use of automated cost-performance analysis is an enabling technology that could bring realistic processbased manufacturing and assembly cost into multidisciplinary design and optimization. In this paper, we present a new methodology for incorporating process costing into a standard multidisciplinary design optimization process. Material, manufacturing processes, and assembly processes costs then could be used as the objective function for the optimization method. A case study involving forty-six different configurations of a simple wing is presented, indicating that a design based on performance criteria alone may not necessarily be the most affordable as far as manufacturing and assembly cost is concerned.

  20. Overview of the Performance and Cost Effectiveness of Small Arsenic Removal Technologies

    Science.gov (United States)

    Presentation provides information on the performance and cost of primarily four arsenic removal technologies; adsorptive media, iron removal, coagulation/filtration and the combination system of iron removal followed by adsorptive media.

  1. Low Cost High Performance Generator Technology Program. Volume 2. Design study

    International Nuclear Information System (INIS)

    1975-06-01

    The systems studies directed towards up-rating the performance of an RTG using selenide thermoelectrics and a heat source with improved safety are reported. The resulting generator design, designated LCHPG, exhibits conversion efficiency of greater than 10 percent, a specific power of 3 W/lb., and a cost of $6,000/W(e). In the course of system analyses, the significant development activities required to achieve this performance by the 1980 time period are identified

  2. Cost-effectiveness of healthy eating and/or physical activity promotion in pregnant women at increased risk of gestational diabetes mellitus

    DEFF Research Database (Denmark)

    Broekhuizen, Karen; Simmons, David; Devlieger, Roland

    2018-01-01

    was performed alongside a European multicenter-randomized controlled trial. A total of 435 pregnant women at increased risk of GDM in primary and secondary care settings in nine European countries, were recruited and randomly allocated to a healthy eating and physical activity promotion intervention (HE + PA...... intervention), a healthy eating promotion intervention (HE intervention), or a physical activity promotion intervention (PA intervention). Main outcome measures were gestational weight gain, fasting glucose, insulin resistance (HOMA-IR), quality adjusted life years (QALYs), and societal costs. Results: Between...... intervention strategy. At 35-37 weeks, it depends on the decision-makers' willingness to pay per kilogram reduction in gestational weight gain whether the HE + PA intervention is cost-effective for gestational weight gain, whereas it was not cost-effective for fasting glucose and HOMA-IR. After delivery...

  3. Productive performance and economic analysis of Santa Inês sheep slaughtered at different subcutaneous fat levels

    Directory of Open Access Journals (Sweden)

    Larissa de Oliveira Queiroz

    2016-03-01

    Full Text Available The objective of this study was to evaluate the productive and economic performance of feedlot-finished Santa Inês lambs slaughtered at three subcutaneous fat levels. Twenty-four uncastrated male lambs with 100 ± 10 days of age and an initial body weight of 22.6 ± 3.9 kg were randomly assigned to three treatments and slaughtered at a subcutaneous fat thickness of 2.0, 3.0 and 4.0 mm. A completely randomized design consisting of three treatments and eight repetitions per treatment was adopted. Productivity parameters included final body weight, dry matter intake, daily and total weight gains, and feed conversion. For the determination of economically viable fat thickness for slaughter, only direct production costs such as lamb purchase costs, feed costs and cost of labor were considered, and revenue, expenses and profit were analyzed. The final body weight and total weight gain differed significantly (P<0.05 between treatments. Lambs slaughtered at a subcutaneous fat thickness of 3.0 and 4.0 mm had a higher final body weight (33.84 ± 1.71 and 34.65 ± 1.79 kg, respectively and total weight gain (9.06 ± 1.04 and 11.82 ± 1.02 kg. However, lambs with 3.0 mm fat thickness exhibited better economic results (profit of US$ 3.10 per kg cold carcass. The slaughter of Santa Inês lambs at 3.0 mm subcutaneous fat thickness is recommended since it provides better productive performance, higher profit per kilogram carcass, and greater profitability.

  4. Cost of intervention delivery in a lifestyle weight loss trial in type 2 diabetes: results from the Look AHEAD clinical trial

    OpenAIRE

    Rushing, J.; Wing, R.; Wadden, T. A.; Knowler, W. C.; Lawlor, M.; Evans, M.; Killean, T.; Montez, M.; Espeland, M. A.; Zhang, P.

    2017-01-01

    Summary Objective The Action for Health in Diabetes (Look AHEAD) trial was a randomized controlled clinical trial to compare the effects of 10?years of intensive lifestyle intervention (ILI) with a control condition of diabetes support and education (DSE) on health outcomes in over 5,000 participants with type 2 diabetes. The ILI had significantly greater weight losses than DSE throughout the trial. The goal of this analysis is to describe the cost of delivering the intervention. Methods The ...

  5. Costs of performance based maintenance for local roads: Case study Albania

    Science.gov (United States)

    Jokanović, Igor; Grujić, Bojana; Zeljić, Dragana; Grujić, Žarko; Svilar, Mila

    2017-12-01

    The provision and maintenance of road infrastructure is a major global business, consequently it is essential that road maintenance services are provided in the most cost effective manner. Without regular maintenance, roads can rapidly fall into disrepair, preventing realization of the longer term impacts of road improvements on development, such as increased agricultural production and growth in school enrollment, which is of particular importance for a network of local (access) roads. Inadequate local roads maintenance in Albania is proposed to be solved by implementing performance based maintenance approach for which the costing exercise is presented within the paper.

  6. Efficacy of manual versus free-weight training to improve maximal strength and performance for microgravity conditions.

    Science.gov (United States)

    Behringer, Michael; Schüren, Thomas; McCourt, Molly; Mester, Joachim

    2016-01-01

    We tested a simple and compact device designed for manual resistance training in conditions of microgravity (Self-Powered Rope Trainer Duo (SPoRT Duo)) to increase muscle performance. Twenty-four participants (20.8 ± 2.1 years) were randomly assigned to a manual resistance group (n = 12) and a free-weight group (n = 12). Participants performed eight exercises (three sets; 8-12 efforts) either with free weights or the SPoRT Duo twice a week for 6 weeks. Maximal isometric force of trunk flexion, back extension and chest press increased (P at least 0.01, d at least 0.52) both in the manual resistance group (18.4% ± 15.0%; 32.7% ± 22.7%; 15.3% ± 9.7%) and free-weight group (18.0% ± 13.9%; 26.6% ± 28.9%; 13.3% ± 7.6%). The change in maximal isometric force of wide grip row in both groups (d at best 0.38) did not reach statistical significance (P at best 0.08). The squat one-repetition-maximum increased in the manual resistance group (29.8% ± 22.1%) and the free-weight group (32.4% ± 26.6%). Jump height, determined by a jump-and-reach test, increased in the free-weight group (9.8% ± 13.2%) but not in the manual resistance group (2.0% ± 8.5%). Manual resistance training was equally effective in increasing strength as traditional resistance training with free weights. This apparatus is a useful addition to current in-flight exercise systems.

  7. Analyzing the Energy Performance, Wind Loading, and Costs of Photovoltaic Slat Modules on Commercial Rooftops

    Energy Technology Data Exchange (ETDEWEB)

    Van Geet, Otto D. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Fu, Ran [National Renewable Energy Lab. (NREL), Golden, CO (United States); Horowitz, Kelsey A. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kurup, Parthiv [National Renewable Energy Lab. (NREL), Golden, CO (United States); MacAlpine, Sara M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Silverman, Timothy J. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2018-02-13

    NREL studied a new type of photovoltaic (PV) module configuration wherein multiple narrow, tilted slats are mounted in a single frame. Each slat of the PV slat module contains a single row of cells and is made using ordinary crystalline silicon PV module materials and processes, including a glass front sheet and weatherproof polymer encapsulation. Compared to a conventional ballasted system, a system using slat modules offer higher energy production and lower weight at lower LCOE. The key benefits of slat modules are reduced wind loading, improved capacity factor and reduced installation cost. First, the individual slats allow air to flow through, which reduce wind loading. Using PV performance modeling software, we compared the performance of an optimized installation of slats modules to a typical installation of conventional modules in a ballasted rack mounting system. Based on the results of the performance modeling two different row tilt and spacing were tested in a wind tunnel. Scaled models of the PV Slat modules were wind tunnel tested to quantify the wind loading of a slat module system on a commercial rooftop, comparing the results to conventional ballasted rack mounted PV modules. Some commercial roofs do not have sufficient reserve dead load capacity to accommodate a ballasted system. A reduced ballast system design could make PV system installation on these roofs feasible for the first time without accepting the disadvantages of penetrating mounts. Finally, technoeconomic analysis was conducted to enable an economic comparison between a conventional commercial rooftop system and a reduced-ballast slat module installation.

  8. The price of performance: a cost and performance analysis of the implementation of cell-free fetal DNA testing for Down syndrome in Ontario, Canada.

    Science.gov (United States)

    Okun, N; Teitelbaum, M; Huang, T; Dewa, C S; Hoch, J S

    2014-04-01

    To examine the cost and performance implications of introducing cell-free fetal DNA (cffDNA) testing within modeled scenarios in a publicly funded Canadian provincial Down syndrome (DS) prenatal screening program. Two clinical algorithms were created: the first to represent the current screening program and the second to represent one that incorporates cffDNA testing. From these algorithms, eight distinct scenarios were modeled to examine: (1) the current program (no cffDNA), (2) the current program with first trimester screening (FTS) as the nuchal translucency-based primary screen (no cffDNA), (3) a program substituting current screening with primary cffDNA, (4) contingent cffDNA with current FTS performance, (5) contingent cffDNA at a fixed price to result in overall cost neutrality,(6) contingent cffDNA with an improved detection rate (DR) of FTS, (7) contingent cffDNA with higher uptake of FTS, and (8) contingent cffDNA with optimized FTS (higher uptake and improved DR). This modeling study demonstrates that introducing contingent cffDNA testing improves performance by increasing the number of cases of DS detected prenatally, and reducing the number of amniocenteses performed and concomitant iatrogenic pregnancy loss of pregnancies not affected by DS. Costs are modestly increased, although the cost per case of DS detected is decreased with contingent cffDNA testing. Contingent models of cffDNA testing can improve overall screening performance while maintaining the provision of an 11- to 13-week scan. Costs are modestly increased, but cost per prenatally detected case of DS is decreased. © 2013 John Wiley & Sons, Ltd.

  9. Performance management and cost effectiveness of public services : empirical evidence from Dutch municipalities

    NARCIS (Netherlands)

    de Groot, Hans; van Hulst, B.L.

    2011-01-01

    The performance of public organizations is one of the key topics in public administration research. Cost-effectiveness as a dimension of performance has hardly been studied in this literature, however. Many governments currently are cutting budgets on an unprecedented scale after the world-wide

  10. Performance Analysis of Low-Cost Single-Frequency GPS Receivers in Hydrographic Surveying

    Science.gov (United States)

    Elsobeiey, M.

    2017-10-01

    The International Hydrographic Organization (IHO) has issued standards that provide the minimum requirements for different types of hydrographic surveys execution to collect data to be used to compile navigational charts. Such standards are usually updated from time to time to reflect new survey techniques and practices and must be achieved to assure both surface navigation safety and marine environment protection. Hydrographic surveys can be classified to four orders namely, special order, order 1a, order 1b, and order 2. The order of hydrographic surveys to use should be determined in accordance with the importance to the safety of navigation in the surveyed area. Typically, geodetic-grade dual-frequency GPS receivers are utilized for position determination during data collection in hydrographic surveys. However, with the evolution of high-sensitivity low-cost single-frequency receivers, it is very important to evaluate the performance of such receivers. This paper investigates the performance of low-cost single-frequency GPS receivers in hydrographic surveying applications. The main objective is to examine whether low-cost single-frequency receivers fulfil the IHO standards for hydrographic surveys. It is shown that the low-cost single-frequency receivers meet the IHO horizontal accuracy for all hydrographic surveys orders at any depth. However, the single-frequency receivers meet only order 2 requirements for vertical accuracy at depth more than or equal 100 m.

  11. The cost of the sword: escape performance in male swordtails.

    Directory of Open Access Journals (Sweden)

    Alex Baumgartner

    2011-01-01

    Full Text Available The handicap theory of sexual selection posits that male display traits that are favored in mate choice come at a significant cost to performance. We tested one facet of this hypothesis in the green swordtail (Xiphophorus helleri. In this species, the lower ray of male caudal fin is extended into a 'sword', which serves to attract potential mates. However, bearing a long sword may increase drag and thus compromise a male's ability to swim effectively. We tested escape performance in this species by eliciting C-start escape responses, an instinctive escape behavior, in males with various sword lengths. We then removed males' swords and retested escape performance. We found no relationship between escape performance and sword length and no effect of sword removal on escape performance. While having a large sword may attract a predator's attention, our results suggest that sword size does not compromise a male's escape performance.

  12. Increase the Performance of Companies in the Energy Sector by Implementing the Activity-Based Costing

    OpenAIRE

    Letitia-Maria Rof; Sorinel Capusneanu

    2015-01-01

    This article highlights the increasing performances as result of implementation stages of the ActivityBased Costing in the companies operating in the energy sector in Romania. There are presented some aspects of the usefulness of applying the Activity-Based Costing in the energy sector and the advantages it offers compared to traditional costing. There are also outlined the steps for applying the Activity-Based Costing and its implementation in the largest hydropower producer in Romania. The ...

  13. Resistance Training using Low Cost Elastic Tubing is Equally Effective to Conventional Weight Machines in Middle-Aged to Older Healthy Adults: A Quasi-Randomized Controlled Clinical Trial.

    Science.gov (United States)

    Lima, Fabiano F; Camillo, Carlos A; Gobbo, Luis A; Trevisan, Iara B; Nascimento, Wesley B B M; Silva, Bruna S A; Lima, Manoel C S; Ramos, Dionei; Ramos, Ercy M C

    2018-03-01

    The objectives of the study were to compare the effects of resistance training using either a low cost and portable elastic tubing or conventional weight machines on muscle force, functional exercise capacity, and health-related quality of life (HRQOL) in middle-aged to older healthy adults. In this clinical trial twenty-nine middle-aged to older healthy adults were randomly assigned to one of the three groups a priori defined: resistance training with elastic tubing (ETG; n = 10), conventional resistance training (weight machines) (CTG; n = 9) and control group (CG, n = 10). Both ETG and CTG followed a 12-week resistance training (3x/week - upper and lower limbs). Muscle force, functional exercise capacity and HRQOL were evaluated at baseline, 6 and 12 weeks. CG underwent the three evaluations with no formal intervention or activity counseling provided. ETG and CTG increased similarly and significantly muscle force (Δ16-44% in ETG and Δ25-46% in CTG, p tubing (a low cost and portable tool) and conventional resistance training using weight machines promoted similar positive effects on peripheral muscle force and functional exercise capacity in middle-aged to older healthy adults.

  14. Impact of some low-cost interventions on students' performance in a ...

    African Journals Online (AJOL)

    Background: Studentsf poor performance in physiology examinations has been worrisome to the university community. Reported preference of peer.tutoring to didactic lectures at the University of Nigeria Medical School has not been investigated. Aim: The aim of this work is to design/implement low.cost interventions to ...

  15. Command vector memory systems: high performance at low cost

    OpenAIRE

    Corbal San Adrián, Jesús; Espasa Sans, Roger; Valero Cortés, Mateo

    1998-01-01

    The focus of this paper is on designing both a low cost and high performance, high bandwidth vector memory system that takes advantage of modern commodity SDRAM memory chips. To successfully extract the full bandwidth from SDRAM parts, we propose a new memory system organization based on sending commands to the memory system as opposed to sending individual addresses. A command specifies, in a few bytes, a request for multiple independent memory words. A command is similar to a burst found in...

  16. Understanding coal quality and its relationship to power plant performance and costs

    Energy Technology Data Exchange (ETDEWEB)

    Jennison, K.D.; Stallard, G.S. [Black & Veatch International, Overland Park, KS (United States)

    1995-12-01

    The availability of reliable, reasonably priced energy is a necessary cornerstone for established and emerging economies. In addition to addressing coal quality issues strictly at a plant level, it is now prudent to consider long-term performance and economics of particular fuel sources to be selected in the light of system economics and reliability. In order to evaluate coal quality issues in a more comprehensive manner, it is important to develop both an approach and a set of tools which can support the various phases of the planning/analysis processes. The processes must consider the following: (1) Cost/availability of other potential coal supplies, including {open_quotes}raw{close_quotes} domestic sources, {open_quotes}cleaned {close_quotes} domestic sources, and other internationally marketed coals. (2) Power plant performance issues as function of plant design and fuel properties. (3) System expansion plans, candidate technologies, and associated capital and operating costs. (4) Projected load demand, for system and for individual units within the system. (5) Legislative issues such as environmental pressures, power purchase agreements, etc. which could alter the solution. (6) Economics of potential plans/strategies based on overall cost-effectiveness of the utility system, not just individual units. (7) Anticipated unit configuration, including addition of environmental control equipment or other repowering options. The Coal Quality Impact Model (CQIM{trademark}) is a PC-based computer program capable of predicting coal-related cost and performance impacts at electric power generating sites. The CQIM was developed for EPRI by Black & Veatch and represents over a decade of effort geared toward developing an extensible state-of-the-art coal quality assessment tool. This paper will introduce CQIM, its capabilities, and its application to Eastern European coal quality assessment needs.

  17. Design, performance and cost of energy from high concentration and flat-plate utility-scale PV systems

    International Nuclear Information System (INIS)

    Stolte, W.J.; Whisnant, R.A.; McGowin, C.R.

    1993-01-01

    This paper presents the results of a recent study to assess the near-term cost of power in central station applications. Three PV technologies were evaluated: Fresnel-lens high-concentration photovoltaic (HCPV), central receiver HCPV, and flat-plate PV using thin-film copper indium diselenide (CIS) cell technology. Baseline assumptions included PV cell designs and performances projected for the 1995 timeframe, 25 and 100 MW/year cell manufacturing rates, 50 MW power plant size, and mature technology cost and performance estimates. The plant design characteristics are highlighted. Potential sites were evaluated and selected for the PV power plants (Carrisa Plains, CA and Apalachicola, FL) and cell manufacturing plants (Dallas-Fort Worth, TX). Conceptual designs and cost estimates were developed for the plants and their components. Plant performance was modeled and the designs were optimized to minimize levelized energy costs. Overall, the flat plate design exhibited the lowest energy costs among the designs evaluated. Its levelized energy costs at the Carrisa Plains site were estimated to be 11.8 and 10.8 cents/kWh (1990 $) for 25 and 100 MW/year module production rates, respectively. This meets the 12 cents/kWh DOE near-term goal. The energy cost of the Fresnel lens plant (at Carrisa Plains and a 100 MW/year cell production rate) was estimated to be 12.4 cents/kWh and the corresponding central receiver energy cost was estimated to be 13.1 cents/kWh, both of which are very close to the DOE goal. Further design optimization efforts are still warranted and can be expected to reduce plant capital costs

  18. Analysing collaborative performance and cost allocation for the joint route planning problem

    OpenAIRE

    Verdonck, Lotte; Ramaekers, Katrien; Depaire, Benoît; Caris, An; Janssens, Gerrit K.

    2017-01-01

    Although organisations become increasingly aware of the inevitable character of horizontal collaboration, surveys report failure rates up to 70 percent for starting strategic partnerships. While a growing body of research acknowledges the importance of the partner selection and cost allocation process, no extensive study has been performed on the numerical relationship between specific company traits, applied allocation mechanisms and collaborative performance. This paper investigates the imp...

  19. Low Cost, High Efficiency, High Pressure Hydrogen Storage

    Energy Technology Data Exchange (ETDEWEB)

    Mark Leavitt

    2010-03-31

    A technical and design evaluation was carried out to meet DOE hydrogen fuel targets for 2010. These targets consisted of a system gravimetric capacity of 2.0 kWh/kg, a system volumetric capacity of 1.5 kWh/L and a system cost of $4/kWh. In compressed hydrogen storage systems, the vast majority of the weight and volume is associated with the hydrogen storage tank. In order to meet gravimetric targets for compressed hydrogen tanks, 10,000 psi carbon resin composites were used to provide the high strength required as well as low weight. For the 10,000 psi tanks, carbon fiber is the largest portion of their cost. Quantum Technologies is a tier one hydrogen system supplier for automotive companies around the world. Over the course of the program Quantum focused on development of technology to allow the compressed hydrogen storage tank to meet DOE goals. At the start of the program in 2004 Quantum was supplying systems with a specific energy of 1.1-1.6 kWh/kg, a volumetric capacity of 1.3 kWh/L and a cost of $73/kWh. Based on the inequities between DOE targets and Quantum’s then current capabilities, focus was placed first on cost reduction and second on weight reduction. Both of these were to be accomplished without reduction of the fuel system’s performance or reliability. Three distinct areas were investigated; optimization of composite structures, development of “smart tanks” that could monitor health of tank thus allowing for lower design safety factor, and the development of “Cool Fuel” technology to allow higher density gas to be stored, thus allowing smaller/lower pressure tanks that would hold the required fuel supply. The second phase of the project deals with three additional distinct tasks focusing on composite structure optimization, liner optimization, and metal.

  20. Health economic aspects of evaluation with diffusion weighted MR and MR colonography compared to standard evaluation with colonoscopy and CT before rectal cancer surgery

    DEFF Research Database (Denmark)

    Achiam, Michael P; Kjellberg, Jakob; Rosenberg, Jacob

    2017-01-01

    calculation and a practical cost calculation. The cost drivers utilized are an average cost based on the cost of all procedures and diagnostic modalities performed in hospitalized patients (DRG) and outpatients (DAGS [Danish outpatient grouping system]) in Denmark. Results The total cost for a full colorectal......) colonography and diffusion-weighted MR of the liver. Purpose To compare the economic aspects of this modality with the standard evaluation in an analysis of the different cost drivers. Material and Methods Based on the results from previous studies, two calculations were performed, a theoretical cost...... the two preoperative diagnostic modalities per patient were €312 and €712, respectively. Conclusion This cost analysis shows the cost effectiveness of the new modality as the future standard preoperative diagnostic work-up by reducing total cost and by having a higher sensitivity and completion rate....

  1. Cost effectiveness of a screen-and-treat program for asymptomatic vaginal infections in pregnancy: towards a significant reduction in the costs of prematurity.

    Science.gov (United States)

    Kiss, H; Pichler, Eva; Petricevic, L; Husslein, P

    2006-08-01

    The purpose of this investigation was to determine the cost-saving potential of a simple screen-and-treat program for vaginal infection, which has previously been shown to lead to a reduction of 50% in the rate of preterm births. To determine the potential cost savings, we compared the direct costs of preterm delivery of infants with a birth weight below 1900g with the costs of the screen-and-treat program. We used a cut-off birth weight of 1900g because, in our population, all infants with a birth weight below 1900g were transferred to the neonatal intensive care unit. The direct costs associated with preterm delivery were defined to include the costs of the initial hospitalization of both mother and infant and the costs of outpatient follow-up throughout the first 6 years of life of the former preterm infant. The costs of the screen-and-treat program were defined to include the costs of the screening examination and the resulting costs of antimicrobial treatment and follow-up. All calculations were based on health-economic data obtained in the metropolitan area of Vienna, Austria. The number of preterm infants with a birth weight below 1900g was 12 (0.5%) in the intervention group (N=2058) and 29 (1.3%) in the control group (N=2097). The direct costs per preterm birth were found to amount to EUR (euro) 60262. Overall, the expected total savings in direct costs achieved by the screen-and-treat program and the ensuing 50% reduction in the number preterm births with a birth weight below 1900g amounted to more than euro 11 million. The costs of screening and treatment were found to amount to merely 7% of the direct costs saved as a result of the screen-and-treat program. A simple preterm prevention program, consisting of screening and antimicrobial treatment and follow-up of women with asymptomatic vaginal infection, leads not only to a significant reduction in the rate of preterm births but also to substantial savings in the direct costs associated with prematurity.

  2. Near Zero Energy House (NZEH) Design Optimization to Improve Life Cycle Cost Performance Using Genetic Algorithm

    Science.gov (United States)

    Latief, Y.; Berawi, M. A.; Koesalamwardi, A. B.; Supriadi, L. S. R.

    2018-03-01

    Near Zero Energy House (NZEH) is a housing building that provides energy efficiency by using renewable energy technologies and passive house design. Currently, the costs for NZEH are quite expensive due to the high costs of the equipment and materials for solar panel, insulation, fenestration and other renewable energy technology. Therefore, a study to obtain the optimum design of a NZEH is necessary. The aim of the optimum design is achieving an economical life cycle cost performance of the NZEH. One of the optimization methods that could be utilized is Genetic Algorithm. It provides the method to obtain the optimum design based on the combinations of NZEH variable designs. This paper discusses the study to identify the optimum design of a NZEH that provides an optimum life cycle cost performance using Genetic Algorithm. In this study, an experiment through extensive design simulations of a one-level house model was conducted. As a result, the study provide the optimum design from combinations of NZEH variable designs, which are building orientation, window to wall ratio, and glazing types that would maximize the energy generated by photovoltaic panel. Hence, the design would support an optimum life cycle cost performance of the house.

  3. PERFORMANCE AND COST OF MERCURY AND MULTIPOLLUTANT EMISSION CONTROL TECHNOLOGY APPLICATIONS ON ELECTRIC UTILITY BOILERS

    Science.gov (United States)

    The report presents estimates of the performance and cost of both powdered activated carbon (PAC) and multipollutant control technologies that may be useful in controlling mercury emissions. Based on currently available data, cost estimates for PAC injection range are 0.03-3.096 ...

  4. Evaluating supplier quality performance using analytical hierarchy process

    Science.gov (United States)

    Kalimuthu Rajoo, Shanmugam Sundram; Kasim, Maznah Mat; Ahmad, Nazihah

    2013-09-01

    This paper elaborates the importance of evaluating supplier quality performance to an organization. Supplier quality performance evaluation reflects the actual performance of the supplier exhibited at customer's end. It is critical in enabling the organization to determine the area of improvement and thereafter works with supplier to close the gaps. Success of the customer partly depends on supplier's quality performance. Key criteria as quality, cost, delivery, technology support and customer service are categorized as main factors in contributing to supplier's quality performance. 18 suppliers' who were manufacturing automotive application parts evaluated in year 2010 using weight point system. There were few suppliers with common rating which led to common ranking observed by few suppliers'. Analytical Hierarchy Process (AHP), a user friendly decision making tool for complex and multi criteria problems was used to evaluate the supplier's quality performance challenging the weight point system that was used for 18 suppliers'. The consistency ratio was checked for criteria and sub-criteria. Final results of AHP obtained with no overlap ratings, therefore yielded a better decision making methodology as compared to weight point rating system.

  5. On the “cost-optimal levels” of energy performance requirements and its economic evaluation in Italy

    Directory of Open Access Journals (Sweden)

    Lamberto Tronchin

    2014-10-01

    Full Text Available The European energy policies about climate and energy package, known as the “20-20-20” targets define ambitious, but achievable, national energy objectives. As regards the Directives closely related to the 2020 targets, the EU Energy Performance of Buildings Directive (EPBD Recast- DIR 2010/31/EU is the main European legislative instrument for improving the energy performance of buildings, taking into account outdoor climatic and local conditions, as well as indoor climate requirements and cost-effectiveness. The EPBD recast now requests that Member States shall ensure that minimum energy performance requirements for buildings are set “with a view to achieving cost-optimal levels”. The cost optimum level shall be calculated in accordance with a comparative methodology framework, leaving the Member States to determine which of these calculations is to become the national benchmark against which national minimum energy performance requirements will be assessed. The European standards (ENs- Umbrella Document V7 (prCEN/TR 15615 are intended to support the EPBD by providing the calculation methods and associated material to obtain the overall energy performance of a building. For Italy the Energy Performance of Building Simulations EPBS must be calculated with standard UNITS 11300. The energy building behaviour is referred to standard and not to real use, nor climate or dynamic energy evaluation. Since retrofitting of existing buildings offers significant opportunities for reducing energy consumption and greenhouse gas emissions, a case study of retrofitting is described and the CostOptimal Level EU procedure in an Italian context is analysed. Following this procedure, it is shown not only that the energy cost depends on several conditions and most of them are not indexed at national level but also that the cost of improvement depends on local variables and contract tender. The case study highlights the difficulties to apply EU rules, and

  6. Physical self-perception and motor performance in normal-weight, overweight and obese children.

    Science.gov (United States)

    Morano, M; Colella, D; Robazza, C; Bortoli, L; Capranica, L

    2011-06-01

    The aim of this study was to examine the relationships among physical self-perception, body image and motor performance in Italian middle school students. Two hundred and sixty children were categorized into normal-weight (n=103), overweight (n=86) or obese (n=71) groups. Perceived coordination, body fat and sports competence were assessed using the Physical Self-Description Questionnaire, while body image was measured using Collins' Child Figure Drawings. Individuals' perceptions of strength, speed and agility were assessed using the Perceived Physical Ability Scale. Tests involving the standing long jump, 2 kg medicine-ball throw, 10 × 5 m shuttle-run and 20 and 30 m sprints were also administered. Girls, when compared with boys, and overweight and obese participants, when compared with normal-weight peers, reported lower perceived and actual physical competence, higher perceived body fat and greater body dissatisfaction. Body dissatisfaction mediated all the associations between body mass index (BMI) and the different aspects of physical self-perception in boys, but not in girls. The same pattern of results was found for physical self-perception as a mediator of the relationship between BMI and body dissatisfaction. In conclusion, obesity proved to have adverse effects on both motor performance and physical self-perception. © 2010 John Wiley & Sons A/S.

  7. Effects of dietary coarsely ground corn and 3 bedding floor types on broiler live performance, litter characteristics, gizzard and proventriculus weight, and nutrient digestibility.

    Science.gov (United States)

    Xu, Y; Lin, Y M; Stark, C R; Ferket, P R; Williams, C M; Brake, J

    2017-07-01

    The effects of zero or 50% dietary coarsely ground corn (CC) in pelleted and screened grower and finisher diets on broilers reared on 3 bedding floor types (plastic net [NET], new pine wood shavings litter [NEW], or old pine wood shavings litter [OLD]) on broiler live performance, litter characteristics, gizzard and proventriculus weight, and apparent ileal digestibility (AID) were studied in a 2 × 3 factorial arrangement of treatments. Fine corn was produced with a hammermill (271 μm) and CC with a roller mill (1145 μm). Utilization of CC reduced milling cost by 9.47 cents per MT with similar nutrient content of screened pellets. The 50% CC treatment exhibited improved (P ≤ 0.05) feed intake at 42 d (2.5%) and 49 d (3.0%), and BW (5.4%) and FCR from 28 d (1.4%). Birds on NEW litter exhibited improved (P litter birds exhibited increased (P ≤ 0.05) gizzard weight at 28 d and 49 d and decreased proventriculus weight as compared to NET at 49 days. The 50% CC treatment exhibited decreased (P ≤ 0.05) litter moisture at 35 and 42 d, litter N at 35 and 49 d, and litter pH at 49 days. OLD litter birds exhibited greater (P litter N at 14, 35, and 49 d, as well as litter moisture, pH, and ammonia concentration at 49 days. The 50% CC group also exhibited improved AID of nitrogen (P Broilers fed pelleted and screened diets containing 50% CC exhibited improved live performance and reduced litter moisture while use of NEW litter resulted in a somewhat similar effect, which indicated that consumption of NEW litter also facilitated gastric development and function. © 2017 Poultry Science Association Inc.

  8. Modeling the Performance and Cost of Lithium-Ion Batteries for Electric-Drive Vehicles - SECOND EDITION

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Paul A. [Argonne National Lab. (ANL), Argonne, IL (United States); Gallagher, Kevin G. [Argonne National Lab. (ANL), Argonne, IL (United States); Bloom, Ira D. [Argonne National Lab. (ANL), Argonne, IL (United States); Dees, Dennis W. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2012-01-01

    This report details the Battery Performance and Cost model (BatPaC) developed at Argonne National Laboratory for lithium-ion battery packs used in automotive transportation. The model designs the battery for a specified power, energy, and type of vehicle battery. The cost of the designed battery is then calculated by accounting for every step in the lithium-ion battery manufacturing process. The assumed annual production level directly affects each process step. The total cost to the original equipment manufacturer calculated by the model includes the materials, manufacturing, and warranty costs for a battery produced in the year 2020 (in 2010 US$). At the time this report is written, this calculation is the only publicly available model that performs a bottom-up lithium-ion battery design and cost calculation. Both the model and the report have been publicly peer-reviewed by battery experts assembled by the U.S. Environmental Protection Agency. This report and accompanying model include changes made in response to the comments received during the peer-review. The purpose of the report is to document the equations and assumptions from which the model has been created. A user of the model will be able to recreate the calculations and perhaps more importantly, understand the driving forces for the results. Instructions for use and an illustration of model results are also presented. Almost every variable in the calculation may be changed by the user to represent a system different from the default values pre-entered into the program. The distinct advantage of using a bottom-up cost and design model is that the entire power-to-energy space may be traversed to examine the correlation between performance and cost. The BatPaC model accounts for the physical limitations of the electrochemical processes within the battery. Thus, unrealistic designs are penalized in energy density and cost, unlike cost models based on linear extrapolations. Additionally, the consequences on

  9. Weight Loss at a Cost: Implications of High-Protein, Low- Carbohydrate Diets.

    Science.gov (United States)

    Gabel, Kathe A.; Lund, Robin J.

    2002-01-01

    Addresses three claims of high-protein, low-carbohydrate diets: weight loss is attributed to the composition of the diet; insulin promotes the storage of fat, thereby, by limiting carbohydrates, dieters will decrease levels of insulin and body fat; and weight loss is the result of fat loss. The paper examines relevant scientific reports and notes…

  10. 19 CFR 10.197 - Direct costs of processing operations performed in a beneficiary country or countries.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Direct costs of processing operations performed in... TO A REDUCED RATE, ETC. Caribbean Basin Initiative § 10.197 Direct costs of processing operations... operations. As used in § 10.195 and § 10.198, the words “direct costs of processing operations” mean those...

  11. Low-cost, high-performance and efficiency computational photometer design

    Science.gov (United States)

    Siewert, Sam B.; Shihadeh, Jeries; Myers, Randall; Khandhar, Jay; Ivanov, Vitaly

    2014-05-01

    Researchers at the University of Alaska Anchorage and University of Colorado Boulder have built a low cost high performance and efficiency drop-in-place Computational Photometer (CP) to test in field applications ranging from port security and safety monitoring to environmental compliance monitoring and surveying. The CP integrates off-the-shelf visible spectrum cameras with near to long wavelength infrared detectors and high resolution digital snapshots in a single device. The proof of concept combines three or more detectors into a single multichannel imaging system that can time correlate read-out, capture, and image process all of the channels concurrently with high performance and energy efficiency. The dual-channel continuous read-out is combined with a third high definition digital snapshot capability and has been designed using an FPGA (Field Programmable Gate Array) to capture, decimate, down-convert, re-encode, and transform images from two standard definition CCD (Charge Coupled Device) cameras at 30Hz. The continuous stereo vision can be time correlated to megapixel high definition snapshots. This proof of concept has been fabricated as a fourlayer PCB (Printed Circuit Board) suitable for use in education and research for low cost high efficiency field monitoring applications that need multispectral and three dimensional imaging capabilities. Initial testing is in progress and includes field testing in ports, potential test flights in un-manned aerial systems, and future planned missions to image harsh environments in the arctic including volcanic plumes, ice formation, and arctic marine life.

  12. Environmental Parametric Cost Model in Oil and Gas EPC Contracts

    Directory of Open Access Journals (Sweden)

    Madjid Abbaspour

    2018-01-01

    Full Text Available This study aims at identifying the parameters that govern the environmental costs in oil and gas projects. An initial conceptual model was proposed. Next, the costs of environmental management work packages were estimated, separately and were applied in project control tools (WBS/CBS. Then, an environmental parametric cost model was designed to determine the environmental costs and relevant weighting factors. The suggested model can be considered as an innovative approach to designate the environmental indicators in oil and gas projects. The validity of variables was investigated based on Delphi method. The results indicated that the project environmental management’s weighting factor is 0.87% of total project’s weighting factor.

  13. Cost Analysis and Performance Assessment of Partner Services for Human Immunodeficiency Virus and Sexually Transmitted Diseases, New York State, 2014.

    Science.gov (United States)

    Johnson, Britney L; Tesoriero, James; Feng, Wenhui; Qian, Feng; Martin, Erika G

    2017-12-01

    To estimate the programmatic costs of partner services for HIV, syphilis, gonorrhea, and chlamydial infection. New York State and local health departments conducting partner services activities in 2014. A cost analysis estimated, from the state perspective, total program costs and cost per case assignment, patient interview, partner notification, and disease-specific key performance indicator. Data came from contracts, a time study of staff effort, and statewide surveillance systems. Disease-specific costs per case assignment (mean: $580; range: $502-$1,111), patient interview ($703; $608-$1,609), partner notification ($1,169; $950-$1,936), and key performance indicator ($2,697; $1,666-$20,255) varied across diseases. Most costs (79 percent) were devoted to gonorrhea and chlamydial infection investigations. Cost analysis complements cost-effectiveness analysis in evaluating program performance and guiding improvements. © Health Research and Educational Trust.

  14. Diet in the management of weight loss

    OpenAIRE

    Strychar, Irene

    2006-01-01

    Obesity is an established risk factor for numerous chronic diseases, and successful treatment will have an important impact on medical resources utilization, health care costs, and patient quality of life. With over 60% of our population being overweight, physicians face a major challenge in assisting patients in the process of weight loss and weight-loss maintenance. Low-calorie diets can lower total body weight by an average of 8% in the short term. These diets are well-tolerated and charac...

  15. Determination of low molecular weight thiols using monobromobimane fluorescent labeling and high-performance liquid chromatography

    Science.gov (United States)

    Fahey, Robert C.; Newton, Gerald L.

    1988-01-01

    Methods are described for the preparation and high-performance liquid chromatography (HPLC) analysis of monobromobimane derivatives of low molecular weight thiols in extracts of biological samples. Typical problems encountered in the development and application of these methods are discussed. Analysis of mung bean extract is used as an example.

  16. Modelling the Cost Performance of a Given Logistics Network Operating Under Regular and Irregular Conditions

    NARCIS (Netherlands)

    Janic, M.

    2009-01-01

    This paper develops an analytical model for the assessment of the cost performance of a given logistics network operating under regular and irregular (disruptive) conditions. In addition, the paper aims to carry out a sensitivity analysis of this cost with respect to changes of the most influencing

  17. Japanese manufacturers' cost-performance marketing strategy for the delivery of solar photovoltaic homes

    International Nuclear Information System (INIS)

    Noguchi, M.

    2005-02-01

    Japanese manufacturers have been gaining a global reputation for their design approaches to industrialized housing, which is often equipped with PV systems. Homes are produced on a cost performance marketing strategy. In 2004, 13.7 per cent of the 1,160,083 houses built in Japan were pre-fabricated. The pre-fabricated housing industry has been given considerable government support. In response to growing demands for sustainable housing, the government has implemented promotional programs aiming to support the installations of photovoltaic systems. Details of various programs were presented, including: value-added production; housing sustainability; PV rooftop systems; and a mass custom design approach. It was concluded that the cost performance marketing strategy has a significant impact on production and design approaches. However, quality-oriented production may also result in successful commercialization of innovative housing. The Japanese marketing approach allows consumers to understand the added value of packaged innovations rather than the cost. It was suggested that this marketing strategy should be examined further, when considering approaches to innovative housing in other countries. 38 refs., 3 figs

  18. A low-cost high-performance embedded platform for accelerator controls

    International Nuclear Information System (INIS)

    Cleva, Stefano; Bogani, Alessio Igor; Pivetta, Lorenzo

    2012-01-01

    Over the last years the mobile and hand-held device market has seen a dramatic performance improvement of the microprocessors employed for these systems. As an interesting side effect, this brings the opportunity of adopting these microprocessors to build small low-cost embedded boards, featuring lots of processing power and input/output capabilities. Moreover, being capable of running a full featured operating system such as Gnu/Linux, and even a control system toolkit such as Tango, these boards can also be used in control systems as front-end or embedded computers. In order to evaluate the feasibility of this idea, an activity has started at Elettra to select, evaluate and validate a commercial embedded device able to guarantee production grade reliability, competitive costs and an open source platform. The preliminary results of this work are presented. (author)

  19. Construction Performance Optimization toward Green Building Premium Cost Based on Greenship Rating Tools Assessment with Value Engineering Method

    Science.gov (United States)

    Latief, Yusuf; Berawi, Mohammed Ali; Basten, Van; Riswanto; Budiman, Rachmat

    2017-07-01

    Green building concept becomes important in current building life cycle to mitigate environment issues. The purpose of this paper is to optimize building construction performance towards green building premium cost, achieving green building rating tools with optimizing life cycle cost. Therefore, this study helps building stakeholder determining building fixture to achieve green building certification target. Empirically the paper collects data of green building in the Indonesian construction industry such as green building fixture, initial cost, operational and maintenance cost, and certification score achievement. After that, using value engineering method optimized green building fixture based on building function and cost aspects. Findings indicate that construction performance optimization affected green building achievement with increasing energy and water efficiency factors and life cycle cost effectively especially chosen green building fixture.

  20. Performance Assessment of a Custom, Portable, and Low-Cost Brain-Computer Interface Platform.

    Science.gov (United States)

    McCrimmon, Colin M; Fu, Jonathan Lee; Wang, Ming; Lopes, Lucas Silva; Wang, Po T; Karimi-Bidhendi, Alireza; Liu, Charles Y; Heydari, Payam; Nenadic, Zoran; Do, An Hong

    2017-10-01

    Conventional brain-computer interfaces (BCIs) are often expensive, complex to operate, and lack portability, which confines their use to laboratory settings. Portable, inexpensive BCIs can mitigate these problems, but it remains unclear whether their low-cost design compromises their performance. Therefore, we developed a portable, low-cost BCI and compared its performance to that of a conventional BCI. The BCI was assembled by integrating a custom electroencephalogram (EEG) amplifier with an open-source microcontroller and a touchscreen. The function of the amplifier was first validated against a commercial bioamplifier, followed by a head-to-head comparison between the custom BCI (using four EEG channels) and a conventional 32-channel BCI. Specifically, five able-bodied subjects were cued to alternate between hand opening/closing and remaining motionless while the BCI decoded their movement state in real time and provided visual feedback through a light emitting diode. Subjects repeated the above task for a total of 10 trials, and were unaware of which system was being used. The performance in each trial was defined as the temporal correlation between the cues and the decoded states. The EEG data simultaneously acquired with the custom and commercial amplifiers were visually similar and highly correlated ( ρ = 0.79). The decoding performances of the custom and conventional BCIs averaged across trials and subjects were 0.70 ± 0.12 and 0.68 ± 0.10, respectively, and were not significantly different. The performance of our portable, low-cost BCI is comparable to that of the conventional BCIs. Platforms, such as the one developed here, are suitable for BCI applications outside of a laboratory.

  1. Cost-effectiveness of diet and exercise interventions to reduce overweight and obesity.

    Science.gov (United States)

    Forster, M; Veerman, J L; Barendregt, J J; Vos, T

    2011-08-01

    To analyze whether two dietary weight loss interventions--the dietary approaches to stop hypertension (DASH) program and a low-fat diet program--would be cost-effective in Australia, and to assess their potential to reduce the disease burden related to excess body weight. We constructed a multi-state life-table-based Markov model in which the distribution of body weight influences the incidence of stroke, ischemic heart disease, hypertensive heart disease, diabetes mellitus, osteoarthritis, post-menopausal breast cancer, colon cancer, endometrial cancer and kidney cancer. The target population was the overweight and obese adult population in Australia in 2003. We used a lifetime horizon for health effects and costs, and a health sector perspective for costs. We populated the model with data identified from Medline and Cochrane searches, Australian Bureau of Statistics published catalogues, Australian Institute of Health and Welfare, and Department of Health and Ageing. Disability adjusted life years (DALYs) averted, incremental cost-effectiveness ratios (ICERs) and proportions of disease burden avoided. ICERs under AUS$50,000 per DALY are considered cost-effective. The DASH and low-fat diet programs have ICERs of AUS$12,000 per DALY (95% uncertainty range: Cost-saving- 68,000) and AUS$13,000 per DALY (Cost-saving--130,000), respectively. Neither intervention reduced the body weight-related disease burden at population level by more than 0.1%. The sensitivity analysis showed that when participants' costs for time and travel are included, the ICERs increase to AUS$75,000 per DALY for DASH and AUS$49,000 per DALY for the low-fat diet. Modest weight loss during the interventions, post-intervention weight regain and low participation limit the health benefits. Diet and exercise interventions to reduce obesity are potentially cost-effective but have a negligible impact on the total body weight-related disease burden.

  2. Comparing Costs of Telephone versus Face-to-Face Extended Care Programs for the Management of Obesity in Rural Settings

    Science.gov (United States)

    Radcliff, Tiffany A.; Bobroff, Linda B.; Lutes, Lesley D.; Durning, Patricia E.; Daniels, Michael J.; Limacher, Marian C.; Janicke, David M.; Martin, A. Daniel; Perri, Michael G.

    2012-01-01

    Background A major challenge following successful weight loss is continuing the behaviors required for long-term weight maintenance. This challenge may be exacerbated in rural areas with limited local support resources. Objective This study describes and compares program costs and cost-effectiveness for 12-month extended care lifestyle maintenance programs following an initial 6-month weight loss program. Design A 1-year prospective controlled randomized clinical trial. Participants/Setting The study included 215 female participants age 50 or older from rural areas who completed an initial 6-month lifestyle program for weight loss. The study was conducted from June 1, 2003, to May 31, 2007. Intervention The intervention was delivered through local Cooperative Extension Service offices in rural Florida. Participants were randomly-assigned to a 12-month extended care program using either individual telephone counseling (n=67), group face-to-face counseling (n=74), or a mail/control group (n=74). Main Outcome Measures Program delivery costs, weight loss, and self-reported health status were directly assessed through questionnaires and program activity logs. Costs were estimated across a range of enrollment sizes to allow inferences beyond the study sample. Statistical Analyses Performed Non-parametric and parametric tests of differences across groups for program outcomes were combined with direct program cost estimates and expected value calculations to determine which scales of operation favored alternative formats for lifestyle maintenance. Results Median weight regain during the intervention year was 1.7 kg for participants in the face-to-face format, 2.1 kg for the telephone format, and 3.1 kg for the mail/control format. For a typical group size of 13 participants, the face-to-face format had higher fixed costs, which translated into higher overall program costs ($420 per participant) when compared to individual telephone counseling ($268 per participant) and

  3. Performances zootechniques et rentabilité financière des ovins en embouche au Burkina Faso

    Directory of Open Access Journals (Sweden)

    Somda J.

    2001-01-01

    Full Text Available Sheep fattening in Burkina Faso: biological performances and profitability. The purpose of this study was to identify the factors affecting the economical and biological performances of lamb fattening operations in rural area. This study was conducted in Oubritenga province in Burkina Faso. Eighty-three rams supplied by 24 producers were involved in the test. Two rations were dispensed during fifty days. Body weight changes and financial operations were monitored. A weight gain model was built to explore growth determinants. Then, cost-benefit ratios were analysed to identify financial efficiency factors. Results show that growth performance depends on the combination of diet and sheep breeds rather than on feed only. Output markets and input marketing policy influence negatively financial cost-effectiveness. This implies firstly, that feed mixes proposed to producers must take species characteristics into account. Secondly, marketing policies enforced on livestock inputs which focus on reducing taxes are indispensable to improve the cost-effetiveness of fattening operations.

  4. Myometrial invasion in endometrial cancer: diagnostic performance of diffusion-weighted MR imaging at 1.5-T

    International Nuclear Information System (INIS)

    Rechichi, Gilda; Sironi, Sandro; Galimberti, Stefania; Valsecchi, Maria Grazia; Signorelli, Mauro; Perego, Patrizia

    2010-01-01

    To determine the diagnostic accuracy of diffusion-weighted (DW) magnetic resonance (MR) imaging in the preoperative assessment of myometrial invasion by endometrial cancer. In this prospective study, 47 patients with histologically confirmed endometrial cancer underwent preoperative MR imaging and total hysterectomy. The MR protocol included spin-echo multishot T2-weighted, dynamic T1-weighted and DW images acquired with b-values of 0 and 500 s/mm 2 . Myometrial tumour spread was classified as superficial (<50%) or deep (≥50% myometrial thickness). Postoperative histopathological findings served as a reference standard. Indices of diagnostic performance were assessed for each sequence. At histopathological examination, superficial myometrial invasion was found in 34 patients and deep myometrial invasion in 13. In the assessment of tumour invasion, sensitivity, specificity, positive and negative predictive values of T2-weighted images were 92.3%, 76.5%, 60.0% and 96.3%, respectively. The corresponding values for dynamic images were 69.2%, 61.8%, 40.9% and 84.0%, and for DW images 84.6%, 70.6%, 52.4% and 92.3%. T2-weighted and DW imaging proved to be the most accurate techniques for tumour spread determination. DW imaging proved to be accurate in assessing myometrial invasion, and it could replace dynamic imaging as an adjunct to routine T2-weighted imaging for preoperative evaluation of endometrial cancer. (orig.)

  5. Effect of the Enabling Perception of Costing Systems by Managers in the Performance of their Tasks

    Directory of Open Access Journals (Sweden)

    Guilherme Eduardo de Souza

    2017-12-01

    Full Text Available The goal of this study is to analyze the effect of the enabling perception of costing systems by managers in the performance of their tasks, mediated by the intensity in of use of these costing systems and the level of psychological empowerment. The research was carried out through a survey of 62 companies listed in the Perfil das Empresas com Projetos Aprovados ou em Implantação na Zona Franca de Manaus Profile of Companies, in 2014. With a view to analyzing the hypotheses replicated from Mahama’s and Cheng’s (2013 study, the Structural Equations Modeling technique wasused. The research results show that the managers’ enabling perception of costing systems does not affect their  intensity of use, but it impacts on psychological empowerment, and this is directly reflected in the performance of tasks, indicating that the greater the empowerment, the better manager performance will be. It isconcluded that the model partially supports the relationships delineated and that the antecedents related to the costing systems require further study.

  6. An assessment of greenhouse gas emissions-weighted clean energy standards

    International Nuclear Information System (INIS)

    Coffman, Makena; Griffin, James P.; Bernstein, Paul

    2012-01-01

    This paper quantifies the relative cost-savings of utilizing a greenhouse gas emissions-weighted Clean Energy Standard (CES) in comparison to a Renewable Portfolio Standard (RPS). Using a bottom-up electricity sector model for Hawaii, this paper demonstrates that a policy that gives “clean energy” credit to electricity technologies based on their cardinal ranking of lifecycle GHG emissions, normalizing the highest-emitting unit to zero credit, can reduce the costs of emissions abatement by up to 90% in comparison to a typical RPS. A GHG emissions-weighted CES provides incentive to not only pursue renewable sources of electricity, but also promotes fuel-switching among fossil fuels and improved generation efficiencies at fossil-fired units. CES is found to be particularly cost-effective when projected fossil fuel prices are relatively low. - Highlights: ► Proposes a GHG Emissions-Weighted Clean Energy Standard (CES) mechanism. ► Compares CES to RPS using a case study of Hawaii. ► Finds CES is up to 90% more cost-effective as a GHG abatement tool.

  7. AN ENHANCED MODEL TO ESTIMATE EFFORT, PERFORMANCE AND COST OF THE SOFTWARE PROJECTS

    Directory of Open Access Journals (Sweden)

    M. Pauline

    2013-04-01

    Full Text Available The Authors have proposed a model that first captures the fundamentals of software metrics in the phase 1 consisting of three primitive primary software engineering metrics; they are person-months (PM, function-points (FP, and lines of code (LOC. The phase 2 consists of the proposed function point which is obtained by grouping the adjustment factors to simplify the process of adjustment and to ensure more consistency in the adjustments. In the proposed method fuzzy logic is used for quantifying the quality of requirements and is added as one of the adjustment factor, thus a fuzzy based approach for the Enhanced General System Characteristics to Estimate Effort of the Software Projects using productivity has been obtained. The phase 3 takes the calculated function point from our work and is given as input to the static single variable model (i.e. to the Intermediate COCOMO and COCOMO II for cost estimation. The Authors have tailored the cost factors in intermediate COCOMO and both; cost and scale factors are tailored in COCOMO II to suite to the individual development environment, which is very important for the accuracy of the cost estimates. The software performance indicators are project duration, schedule predictability, requirements completion ratio and post-release defect density, are also measured for the software projects in my work. A comparative study for effort, performance measurement and cost estimation of the software project is done between the existing model and the authors proposed work. Thus our work analyzes the interaction¬al process through which the estimation tasks were collectively accomplished.

  8. Comparing methodologies for the allocation of overhead and capital costs to hospital services.

    Science.gov (United States)

    Tan, Siok Swan; van Ineveld, Bastianus Martinus; Redekop, William Ken; Hakkaart-van Roijen, Leona

    2009-06-01

    Typically, little consideration is given to the allocation of indirect costs (overheads and capital) to hospital services, compared to the allocation of direct costs. Weighted service allocation is believed to provide the most accurate indirect cost estimation, but the method is time consuming. To determine whether hourly rate, inpatient day, and marginal mark-up allocation are reliable alternatives for weighted service allocation. The cost approaches were compared independently for appendectomy, hip replacement, cataract, and stroke in representative general hospitals in The Netherlands for 2005. Hourly rate allocation and inpatient day allocation produce estimates that are not significantly different from weighted service allocation. Hourly rate allocation may be a strong alternative to weighted service allocation for hospital services with a relatively short inpatient stay. The use of inpatient day allocation would likely most closely reflect the indirect cost estimates obtained by the weighted service method.

  9. Review of PV Inverter Technology Cost and Performance Projections

    Energy Technology Data Exchange (ETDEWEB)

    Navigant Consulting Inc.

    2006-01-01

    The National Renewable Energy Laboratory (NREL) has a major responsibility in the implementation of the U.S. Department of Energy's (DOE's) Solar Energy Technologies Program. Sandia National Laboratories (SNL) has a major role in supporting inverter development, characterization, standards, certifications, and verifications. The Solar Energy Technologies Program recently published a Multiyear Technical Plan, which establishes a goal of reducing the Levelized Energy Cost (LEC) for photovoltaic (PV) systems to $0.06/kWh by 2020. The Multiyear Technical Plan estimates that, in order to meet the PV system goal, PV inverter prices will need to decline to $0.25-0.30 Wp by 2020. DOE determined the need to conduct a rigorous review of the PV Program's technical and economic targets, including the target set for PV inverters. NREL requested that Navigant Consulting Inc.(NCI) conduct a review of historical and projected cost and performance improvements for PV inverters, including identification of critical barriers identified and the approaches government might use to address them.

  10. Low-Cost High-Performance MRI

    Science.gov (United States)

    Sarracanie, Mathieu; Lapierre, Cristen D.; Salameh, Najat; Waddington, David E. J.; Witzel, Thomas; Rosen, Matthew S.

    2015-10-01

    Magnetic Resonance Imaging (MRI) is unparalleled in its ability to visualize anatomical structure and function non-invasively with high spatial and temporal resolution. Yet to overcome the low sensitivity inherent in inductive detection of weakly polarized nuclear spins, the vast majority of clinical MRI scanners employ superconducting magnets producing very high magnetic fields. Commonly found at 1.5-3 tesla (T), these powerful magnets are massive and have very strict infrastructure demands that preclude operation in many environments. MRI scanners are costly to purchase, site, and maintain, with the purchase price approaching $1 M per tesla (T) of magnetic field. We present here a remarkably simple, non-cryogenic approach to high-performance human MRI at ultra-low magnetic field, whereby modern under-sampling strategies are combined with fully-refocused dynamic spin control using steady-state free precession techniques. At 6.5 mT (more than 450 times lower than clinical MRI scanners) we demonstrate (2.5 × 3.5 × 8.5) mm3 imaging resolution in the living human brain using a simple, open-geometry electromagnet, with 3D image acquisition over the entire brain in 6 minutes. We contend that these practical ultra-low magnetic field implementations of MRI (standards for affordable (<$50,000) and robust portable devices.

  11. A STUDY ON THE ABC APPROACH IN COST MANAGEMENT PRACTICE

    Directory of Open Access Journals (Sweden)

    Violeta ISAI

    2014-06-01

    Full Text Available Activity-based costing (ABC, an alternative approach to traditional accounting, represents a costing methodology that identifies the main cost drivers, or the main activities in an organization, thus assigning the cost of the products and services according to the number of specific activities or transactions used in the development process of a product or service. This system is based on the measurement of all the activities performed within an organization and provides the companies with the opportunity to efficiently improve their activity or to reduce the costs with no quality loss for their customers. The primary aim of ABC method was to implement a logical system of additional allocation with a better information and improvement in the field of managerial policies, a real cost structure on the basis of which strategic managerial decisions could be further adopted. Under the terms of a continuous growth of fixed cost weighting, we will become more interested in the calculation system of process costing. This costs calculation method can bring on important benefits, especially for service provider companies, considering the high share of common- indirect costs (overhead, in their unit.

  12. LCP- LIFETIME COST AND PERFORMANCE MODEL FOR DISTRIBUTED PHOTOVOLTAIC SYSTEMS

    Science.gov (United States)

    Borden, C. S.

    1994-01-01

    The Lifetime Cost and Performance (LCP) Model was developed to assist in the assessment of Photovoltaic (PV) system design options. LCP is a simulation of the performance, cost, and revenue streams associated with distributed PV power systems. LCP provides the user with substantial flexibility in specifying the technical and economic environment of the PV application. User-specified input parameters are available to describe PV system characteristics, site climatic conditions, utility purchase and sellback rate structures, discount and escalation rates, construction timing, and lifetime of the system. Such details as PV array orientation and tilt angle, PV module and balance-of-system performance attributes, and the mode of utility interconnection are user-specified. LCP assumes that the distributed PV system is utility grid interactive without dedicated electrical storage. In combination with a suitable economic model, LCP can provide an estimate of the expected net present worth of a PV system to the owner, as compared to electricity purchased from a utility grid. Similarly, LCP might be used to perform sensitivity analyses to identify those PV system parameters having significant impact on net worth. The user describes the PV system configuration to LCP via the basic electrical components. The module is the smallest entity in the PV system which is modeled. A PV module is defined in the simulation by its short circuit current, which varies over the system lifetime due to degradation and failure. Modules are wired in series to form a branch circuit. Bypass diodes are allowed between modules in the branch circuits. Branch circuits are then connected in parallel to form a bus. A collection of buses is connected in parallel to form an increment to capacity of the system. By choosing the appropriate series-parallel wiring design, the user can specify the current, voltage, and reliability characteristics of the system. LCP simulation of system performance is site

  13. Gestational age and birth weight in relation to school performance of 10-year-old children: a follow-up study of children born after 32 completed weeks

    DEFF Research Database (Denmark)

    Kirkegaard, Ida; Obel, Carsten; Hedegaard, Morten

    2006-01-01

    BACKGROUND: Children born extremely premature (weight (weight. Much less is known about children of higher gestational ages and birth weights. We studied gestational age...... after 32 completed weeks and birth weight in relation to the child's school performance at the age of 10 years. METHODS: We performed a follow-up study of 5319 children born between January 1990 and June 1992. We got the information on birth weight and gestational age from birth registration forms; when...... the children were between 9 and 11 years of age, we gathered information about their school performance (reading, spelling, and arithmetic) from questionnaires completed by the parents and the children's primary school teachers. RESULTS: The association between birth weight and reading, as well as spelling...

  14. Cost-effectiveness analysis of ultrasonography screening for nonalcoholic fatty liver disease in metabolic syndrome patients

    Science.gov (United States)

    Phisalprapa, Pochamana; Supakankunti, Siripen; Charatcharoenwitthaya, Phunchai; Apisarnthanarak, Piyaporn; Charoensak, Aphinya; Washirasaksiri, Chaiwat; Srivanichakorn, Weerachai; Chaiyakunapruk, Nathorn

    2017-01-01

    Abstract Background: Nonalcoholic fatty liver disease (NAFLD) can be diagnosed early by noninvasive ultrasonography; however, the cost-effectiveness of ultrasonography screening with intensive weight reduction program in metabolic syndrome patients is not clear. This study aims to estimate economic and clinical outcomes of ultrasonography in Thailand. Methods: Cost-effectiveness analysis used decision tree and Markov models to estimate lifetime costs and health benefits from societal perspective, based on a cohort of 509 metabolic syndrome patients in Thailand. Data were obtained from published literatures and Thai database. Results were reported as incremental cost-effectiveness ratios (ICERs) in 2014 US dollars (USD) per quality-adjusted life year (QALY) gained with discount rate of 3%. Sensitivity analyses were performed to assess the influence of parameter uncertainty on the results. Results: The ICER of ultrasonography screening of 50-year-old metabolic syndrome patients with intensive weight reduction program was 958 USD/QALY gained when compared with no screening. The probability of being cost-effective was 67% using willingness-to-pay threshold in Thailand (4848 USD/QALY gained). Screening before 45 years was cost saving while screening at 45 to 64 years was cost-effective. Conclusions: For patients with metabolic syndromes, ultrasonography screening for NAFLD with intensive weight reduction program is a cost-effective program in Thailand. Study can be used as part of evidence-informed decision making. Translational Impacts: Findings could contribute to changes of NAFLD diagnosis practice in settings where economic evidence is used as part of decision-making process. Furthermore, study design, model structure, and input parameters could also be used for future research addressing similar questions. PMID:28445256

  15. Cost analysis of iliac stenting performed in the operating room and the catheterization lab: A case-control study.

    Science.gov (United States)

    Kim, Sooyeon; Kramer, Sage P; Dugan, Adam J; Minion, David J; Gurley, John C; Davenport, Daniel L; Ferraris, Victor A; Saha, Sibu P

    2016-12-01

    Iliac arterial stenting is performed both in the operating room (OR) and the catheterization lab (CL). To date, no analysis has compared resource utilization between these locations. Consecutive patients (n = 105) treated at a single center were retrospectively analyzed. Patients included adults with chronic, symptomatic iliac artery stenosis with a minimum Rutherford classification (RC) of 3, treated with stents. Exclusion criteria were prior stenting, acute ischemia, or major concomitant procedures. Immediate and two-year outcomes were observed. Patient demographics, perioperative details, physician billings, and hospital costs were recorded. Multivariable regression was used to adjust costs by patient and perioperative cost drivers. Fifty-one procedures (49%) were performed in the OR and 54 (51%) in the CL. Mean age was 57, and 44% were female. Severe cases were more often performed in the OR (RC ≥ 4; 42% vs. 11%, P costs (P costs (P costs but was associated with increased professional fees. Same-stay (5%) and post-discharge reintervention (33%) did not vary by location. The OR was associated with increased length of stay, more ICU admissions, and increased total costs. However, OR patients had more severe disease and therefore often required more aggressive intervention. After controlling for these differences, procedure venue per se was not associated with increased costs, but OR cases incurred increased professional fees due to dual-provider charges. Given the similar clinical results between venues, it seems reasonable to perform most stenting in the CL or utilize conscious sedation in the OR. Copyright © 2016 IJS Publishing Group Ltd. Published by Elsevier Ltd. All rights reserved.

  16. Effects of inclusion Aspergillus niger fermented shrimp waste meal in broiler diets on live performance and digestive organ weight

    Directory of Open Access Journals (Sweden)

    Irfan H. Djunaidi

    2009-06-01

    Full Text Available An experiment was conducted to evaluate the effect of the inclusion of different levels of shrimp waste meal fermented with Aspergillus niger (LUF in diets on growth performance and digestive organ weight of broilers. A total of 75 d-old chicks were randomly allocated to 5 (five treatments in 3 replication pens of 5 birds each. Treatments consisted of LUF inclusion of 0 (control, and 5, 7.5, 10 and 12,5% (P0, P1, P2, P3 and P4 in the diets. Birds were raised under standard condition and provided with feed and water ad-libitum. Feed and birds were weighed weekly up to 35 days to determine body weight, feed intake and feed conversion. At the end of experimental period, the birds were slaughatered and dressed up to determine carcass percentage and digestive organ weight. There was a significant negative linear response in body weight, feed consumption and feed conversion with increase of LUF more than 7.5% in the diets until 35 days of age, but % carcass was almost the same for all treatment. There was no significant response in digestive organ weight with increasing levels of LUF. The present result indicated that LUF could be considered as a potential feed ingredient as protein source of broiler but its inclusion should be limited until 7.5% of the diet to maintain growth performance and digestive organ weight.

  17. Turboelectric Aircraft Drive Key Performance Parameters and Functional Requirements

    Science.gov (United States)

    Jansen, Ralph H.; Brown, Gerald V.; Felder, James L.; Duffy, Kirsten P.

    2016-01-01

    The purpose of this paper is to propose specific power and efficiency as the key performance parameters for a turboelectric aircraft power system and investigate their impact on the overall aircraft. Key functional requirements are identified that impact the power system design. Breguet range equations for a base aircraft and a turboelectric aircraft are found. The benefits and costs that may result from the turboelectric system are enumerated. A break-even analysis is conducted to find the minimum allowable electric drive specific power and efficiency that can preserve the range, initial weight, operating empty weight, and payload weight of the base aircraft.

  18. Application of Activity-Based Costing Management System by Key Success Paths to Promote the Competitive Advantages and Operation Performance

    OpenAIRE

    Mei-Fang Wu; Shu-Li Wang; Feng-Tsung Cheng

    2015-01-01

    Highly developed technology and highly competitive global market highlight the important role of competitive advantages and operation performances in sustainable company operation. Activity-Based Costing (ABC) provides accurate operation cost and operation performance information. Rich literatures provide relevant research with cases study on Activity-Based Costing application, but the research on cause relationship between key success factors and its specific outcome, su...

  19. Energy technologies for distributed utility applications: Cost and performance trends, and implications for photovoltaics

    International Nuclear Information System (INIS)

    Eyer, J.M.

    1994-01-01

    Utilities are evaluating several electric generation and storage (G ampersand S) technologies for distributed utility (DU) applications. Attributes of leading DU technologies and implications for photovoltaics (PV) are described. Included is a survey of present and projected cost and performance for: (1) small, advanced combustion turbines (CTs); (2) advanced, natural gas-fired, diesel engines (diesel engines); and (3) advanced lead-acid battery systems (batteries). Technology drivers and relative qualitative benefits are described. A levelized energy cost-based cost target for PV for DU applications is provided. The analysis addresses only relative cost, for PV and for three selected alternative DU technologies. Comparable size, utility, and benefits are assumed, although relative value is application-specific and often technology- and site-specific

  20. Performance and cost implications of the Fixed Mirror, Distributed Focus (FMDF) collector

    International Nuclear Information System (INIS)

    Dirks, J.A.; Williams, T.A.; Brown, D.R.

    1992-01-01

    The Fixed Mirror, Distributed Focus (FMDF) hemispherical bowl is a solar thermal power technology which has been studied for several years as a potentially attractive means of producing electricity. This paper discusses projections of the collector (concentrator and receiver) performance and cost that could be achieved by five variations of the FMDF technology, based on the assumption of continued technology development and high volume production. The major loss mechanisms were determined for the concentrators and receivers and then design point losses and efficiencies were developed. The Pacific Northwest Laboratory (PNL) computer code SOLDSTEP was then used to determine the annual performance. The cost analysis was based on a commercial solar thermal industry that could exist by the late 1990s. The industry is assumed to be installing several hundred megawatts per year of electric capacity, and is assumed to have improved the maturity of solar thermal components so that technical and economic risks are similar to other energy systems

  1. Efficiency of Individual Tree Detection Approaches Based on Light-Weight and Low-Cost UAS Imagery in Australian Savannas

    Directory of Open Access Journals (Sweden)

    Grigorijs Goldbergs

    2018-01-01

    Full Text Available The reliability of airborne light detection and ranging (LiDAR for delineating individual trees and estimating aboveground biomass (AGB has been proven in a diverse range of ecosystems, but can be difficult and costly to commission. Point clouds derived from structure from motion (SfM matching techniques obtained from unmanned aerial systems (UAS could be a feasible low-cost alternative to airborne LiDAR scanning for canopy parameter retrieval. This study assesses the extent to which SfM three-dimensional (3D point clouds—obtained from a light-weight mini-UAS quadcopter with an inexpensive consumer action GoPro camera—can efficiently and effectively detect individual trees, measure tree heights, and provide AGB estimates in Australian tropical savannas. Two well-established canopy maxima and watershed segmentation tree detection algorithms were tested on canopy height models (CHM derived from SfM imagery. The influence of CHM spatial resolution on tree detection accuracy was analysed, and the results were validated against existing high-resolution airborne LiDAR data. We found that the canopy maxima and watershed segmentation routines produced similar tree detection rates (~70% for dominant and co-dominant trees, but yielded low detection rates (<35% for suppressed and small trees due to poor representativeness in point clouds and overstory occlusion. Although airborne LiDAR provides higher tree detection rates and more accurate estimates of tree heights, we found SfM image matching to be an adequate low-cost alternative for the detection of dominant and co-dominant tree stands.

  2. Applying a new unequally weighted feature fusion method to improve CAD performance of classifying breast lesions

    Science.gov (United States)

    Zargari Khuzani, Abolfazl; Danala, Gopichandh; Heidari, Morteza; Du, Yue; Mashhadi, Najmeh; Qiu, Yuchen; Zheng, Bin

    2018-02-01

    Higher recall rates are a major challenge in mammography screening. Thus, developing computer-aided diagnosis (CAD) scheme to classify between malignant and benign breast lesions can play an important role to improve efficacy of mammography screening. Objective of this study is to develop and test a unique image feature fusion framework to improve performance in classifying suspicious mass-like breast lesions depicting on mammograms. The image dataset consists of 302 suspicious masses detected on both craniocaudal and mediolateral-oblique view images. Amongst them, 151 were malignant and 151 were benign. The study consists of following 3 image processing and feature analysis steps. First, an adaptive region growing segmentation algorithm was used to automatically segment mass regions. Second, a set of 70 image features related to spatial and frequency characteristics of mass regions were initially computed. Third, a generalized linear regression model (GLM) based machine learning classifier combined with a bat optimization algorithm was used to optimally fuse the selected image features based on predefined assessment performance index. An area under ROC curve (AUC) with was used as a performance assessment index. Applying CAD scheme to the testing dataset, AUC was 0.75+/-0.04, which was significantly higher than using a single best feature (AUC=0.69+/-0.05) or the classifier with equally weighted features (AUC=0.73+/-0.05). This study demonstrated that comparing to the conventional equal-weighted approach, using an unequal-weighted feature fusion approach had potential to significantly improve accuracy in classifying between malignant and benign breast masses.

  3. Very low birth weight piglets show improved cognitive performance in the spatial cognitive holeboard task

    Directory of Open Access Journals (Sweden)

    Alexandra eAntonides

    2015-02-01

    Full Text Available Low birth weight (LBW is common in humans and has been found to cause lasting cognitive and developmental deficits later in life. It is thought that the primary cause is intra-uterine growth restriction due to a shortage of oxygen and nutrients supply to the fetus. Pigs appear to be a good model animal to investigate long-term cognitive effects of LBW, as LBW is common in commercially farmed breeds of pigs. Moreover, pigs are developmentally similar to humans and can be trained to perform complex tasks. In this study, we trained ten very low birth weight (vLBW piglets and their ten normal birth weight (NBW siblings in a spatial cognitive holeboard task in order to investigate long-term cognitive effects of LBW. In this task, four out of sixteen holes contain a hidden food reward, which allows measuring working memory (short-term and reference memory (long-term in parallel. Piglets were trained for 46-54 trials during the acquisition phase, followed by a 20-trial reversal phase in which a different set of four holes was baited. Both groups acquired the task and improved their performance over time. A mixed model repeated measures ANOVA revealed that vLBW piglets showed a better reference memory performance than NBW piglets in both the acquisition and reversal phase. Additionally, the vLBW piglets fell back less in working memory scores than the NBW animals when switched to the reversal phase. These findings are contrary to findings in humans. Moreover, vLBW pigs had lower hair cortisol concentrations than NBW pigs in flank hair at 12 weeks of age. These results could indicate that restricted intra-uterine growth causes compensatory mechanisms to arise in early development that result in beneficial effects for vLBW piglets, increasing their low survival chances in early-life competition.

  4. Very low birth weight piglets show improved cognitive performance in the spatial cognitive holeboard task.

    Science.gov (United States)

    Antonides, Alexandra; Schoonderwoerd, Anne C; Nordquist, Rebecca E; van der Staay, Franz Josef

    2015-01-01

    Low birth weight (LBW) is common in humans and has been found to cause lasting cognitive and developmental deficits later in life. It is thought that the primary cause is intra-uterine growth restriction (IUGR) due to a shortage of oxygen and supply of nutrients to the fetus. Pigs appear to be a good model animal to investigate long-term cognitive effects of LBW, as LBW is common in commercially farmed breeds of pigs. Moreover, pigs are developmentally similar to humans and can be trained to perform complex tasks. In this study, we trained ten very low birth weight (vLBW) piglets and their ten normal birth weight (NBW) siblings in a spatial cognitive holeboard task in order to investigate long-term cognitive effects of LBW. In this task, four out of sixteen holes contain a hidden food reward, which allows measuring working memory (WM) (short-term memory) and reference memory (RM) (long-term memory) in parallel. Piglets were trained for 46-54 trials during the acquisition phase, followed by a 20-trial reversal phase in which a different set of four holes was baited. Both groups acquired the task and improved their performance over time. A mixed model repeated measures ANOVA revealed that vLBW piglets showed better RM performance than NBW piglets in both the acquisition and reversal phase. Additionally, WM scores in the vLBW were less disrupted than in the NBW animals when switched to the reversal phase. These findings are contrary to findings in humans. Moreover, vLBW pigs had lower hair cortisol concentrations (HCCs) than NBW pigs in flank hair at 12 weeks of age. These results could indicate that restricted intra-uterine growth causes compensatory mechanisms to arise in early development that result in beneficial effects for vLBW piglets, increasing their low survival chances in early-life competition.

  5. Design to Cost and Life Cycle Cost.

    Science.gov (United States)

    1980-07-01

    MANAGEMENT TASK ORIENTATED COST STRUCTURE 5. COSTS OF CONSTRUCTION INIFRA 2. COSTS DURING DEVELOPMENT -6. COSTS OF TRAINING 3. COSTS DURING TESi ...de r~duction des coats, ii faut disponer de ?!vyenr. performants d’eetimation des coats en main-d’oeuvre et en applrvininrinesent. Cam moyenm doivent

  6. Effects of high grade bentonite on performance, organ weights and serum biochemistry during aflatoxicosis in broilers

    Directory of Open Access Journals (Sweden)

    H. C. Indresh

    2013-12-01

    Full Text Available Aim: To evaluate the effect of different levels of High Bentonite on growth performance, organ weight and serum biochemistry in broiler fed on diets containing aflatoxin. Materials and Methods: A total of 360 day-old commercial broiler chicks were divided at random into 8 dietary treatment groups of 42 chicks each having 3 replicates. Dietary levels of aflatoxin (0.5 ppm and High-grade bentonite (0.5, 0.75 and 1.00% were tested in a completely randomized design manner, forming a total of 8 dietary treatments each with three replicates. Body weight and feed intake were recorded weekly. At 5 wk, six birds from each treatment were sacrificed and liver, kidney, gizzard, pancreas, spleen, bursa of Fabricius and thymus were extracted and weighed. The serum samples were analyzed for total proteins, uric acid, serum albumin, serum globulin and the activities of gamma glutamyl transferase (GGT, alanine amino transferase (ALT and for antibody titers against Newcastle disease (ND and infectious bursal disease (IBD using ELISA technique. Results: A significant (P<0.05 decrease in body weight, feed consumption, relative weights of bursa, thymus, serum protein, anti body titers against NDV and IBDV, and increase in FCR, mortality, relative weight of liver, kidney, and the activity of Gamma Glutamyl Transferase (GGT was observed. However, the relative weights of gizzard, pancreas, spleen, serum albumin, uric acid and the activity of Alanine Amino Transferase (ALT were not influenced by inclusion of AF or HGB. Conclusion: The addition of HGB restored the harmful effects of AF on body weight, feed consumption, FCR, mortality, relative weight of liver, kidney, serum protein, IBDV and NDV. Supplementation of high grade bentonite at 1.0 per cent level was found to be beneficial in ameliorating the adverse effects of aflatoxin (AF in broiler chickens. [Vet World 2013; 6(6.000: 313-317

  7. Physiological Costs of Repetitive Courtship Displays in Cockroaches Handicap Locomotor Performance

    Science.gov (United States)

    Mowles, Sophie L.; Jepson, Natalie M.

    2015-01-01

    Courtship displays are typically thought to have evolved via female choice, whereby females select mates based on the characteristics of a display that is expected to honestly reflect some aspect of the male’s quality. Honesty is typically enforced by mechanistic costs and constraints that limit the level at which a display can be performed. It is becoming increasingly apparent that these costs may be energetic costs involved in the production of dynamic, often repetitive displays. A female attending to such a display may thus be assessing the physical fitness of a male as an index of his quality. Such assessment would provide information on his current physical quality as well as his ability to carry out other demanding activities, qualities with which a choosy female should want to provision her offspring. In the current study we use courtship interactions in the Cuban burrowing cockroach, Byrsotria fumigata to directly test whether courtship is associated with a signaler’s performance capacity. Males that had produced courtship displays achieved significantly lower speeds and distances in locomotor trials than non-courting control males. We also found that females mated more readily with males that produced a more vigorous display. Thus, males of this species have developed a strategy where they produce a demanding courtship display, while females choose males based on their ability to produce this display. Courtship displays in many taxa often involve dynamic repetitive actions and as such, signals of stamina in courtship may be more widespread than previously thought. PMID:26606147

  8. Behaviour and growth performance of low-birth-weight piglets cross-fostered in multiparous sows with piglets of higher birth weights

    Directory of Open Access Journals (Sweden)

    L.P. Souza

    2014-04-01

    Full Text Available The aim of the study was to evaluate the behaviour, pre-weaning survival rate and growth performance of low birth weight (BW piglets cross-fostered with piglets of higher weights. Piglets were transferred to 60 foster sows, and divided in three groups (G; n=20: G1- 12 low BW piglets (0.80 - 1.25kg; G2- six low BW piglets and six intermediate BW piglets (1.40 - 1.60kg, and G3- six low BW piglets and six high BW piglets (>1.70kg. For the analysis, groups G2 and G3 were subdivided in LG2 (six G2 light piglets; IG2 (six G2 intermediate piglets, LG3 (six G3 light piglets, and HG3 (six G3 heavy piglets. Behavioural observations were carried out on days 1, 2, 4 and 6 (visual direct observation and on days 3 and 5 (video recording after birth. The percentage of missed nursings was higher in LG3 piglets than in LG1, IG2 and HG3 piglets, on days 1 and 2. On day 4, light piglets (LG1, LG2 and LG3 missed more nursings than IG2 and HG3 piglets. On day 3, video recording showed a higher percentage of missed nursings in LG1, LG2, and LG3 piglets as compared to HG3 piglets. On day 1, the number of fights during nursing was higher in IG2 than in LG1 and LG3 piglets. Also on day 1, number of fights and percentage of piglets engaged in fights, during 15min after nursing, were higher in LG1, LG3 and HG3 than in LG2 piglets. More playful behaviours were observed on day 2 in IG2 and HG3 piglets compared to LG1, LG2 and LG3 piglets. Light piglets (LG1, LG2, and LG3 presented similar body weight on days 4, 8, 12 and 16 after birth, regardless of being mixed with piglets of higher weights or not; however, the survival rate until day 16 was most compromised in LG3 piglets compared to the other groups. Despite the lack of influence of littermates' weight on the growth of low BW piglets, their survival rate indicates that they should not be mixed with high BW piglets.

  9. Optimal design of multi-state weighted k-out-of-n systems based on component design

    International Nuclear Information System (INIS)

    Li Wei; Zuo, Ming J.

    2008-01-01

    This paper presents a study on design optimization of multi-state weighted k-out-of-n systems. The studied system reliability model is more general than the traditional k-out-of-n system model. The system and its components are capable of assuming a whole range of performance levels, varying from perfect functioning to complete failure. A utility value corresponding to each state is used to indicate the corresponding performance level. A widely studied reliability optimization problem is the 'component selection problem', which involves selection of components with known reliability and cost characteristics. Less adequately addressed has been the problem of determining system cost and utility based on the relationships between component reliability, cost and utility. This paper addresses this topic. All the optimization problems dealt with in this paper can be categorized as either minimizing the expected total system cost subject to system reliability requirements, or maximizing system reliability subject to total system cost limitation. The resulting optimization problems are too complicated to be solved by traditional optimization approaches; therefore, genetic algorithm (GA) is used to solve them. Our results show that GA is a powerful tool for solving these kinds of problems

  10. A low cost, high performance, 1.2m off-axis telescope built with NG-Xinetics silicon carbide

    Science.gov (United States)

    Rey, Justin J.; Wellman, John A.; Egan, Richard G.; Wollensak, Richard J.

    2011-09-01

    The search for extrasolar habitable planets is one of three major astrophysics priorities identified for the next decade. These missions demand very high performance visible-wavelength optical imaging systems. Such high performance space telescopes are typically extremely expensive and can be difficult for government agencies to afford in today's economic climate, and most lower cost systems offer little benefit because they fall short on at least one of the following three key performance parameters: imaging wavelength, total system-level wavefront error and aperture diameter. Northrop Grumman Xinetics has developed a simple, lightweight, low-cost telescope design that will address the near-term science objectives of this astrophysics theme with the required optical performance, while reducing the telescope cost by an order of magnitude. Breakthroughs in SiC mirror manufacturing, integrated wavefront sensing, and high TRL deformable mirror technology have finally been combined within the same organization to offer a complete end-to-end telescope system in the lower end of the Class D cost range. This paper presents the latest results of real OAP polishing and metrology data, an optimized optical design, and finite element derived WFE

  11. Distributed utility technology cost, performance, and environmental characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Wan, Y; Adelman, S

    1995-06-01

    Distributed Utility (DU) is an emerging concept in which modular generation and storage technologies sited near customer loads in distribution systems and specifically targeted demand-side management programs are used to supplement conventional central station generation plants to meet customer energy service needs. Research has shown that implementation of the DU concept could provide substantial benefits to utilities. This report summarizes the cost, performance, and environmental and siting characteristics of existing and emerging modular generation and storage technologies that are applicable under the DU concept. It is intended to be a practical reference guide for utility planners and engineers seeking information on DU technology options. This work was funded by the Office of Utility Technologies of the US Department of Energy.

  12. Effects of sprint interval training and body weight reduction on power to weight ratio in experienced cyclists.

    Science.gov (United States)

    Lunn, William R; Finn, Joan A; Axtell, Robert S

    2009-07-01

    The purpose of this study was to determine the effect of supramaximal sprint interval training (SIT), body weight reduction, and a combination of both treatments on peak and average anaerobic power to weight ratio (PPOan:Wt, APOan:Wt) by manipulating peak and average anaerobic power output (PPOan, APOan) and body weight (BW) in experienced cyclists. Participants (N = 34, age = 38.0 +/- 7.1 years) were assigned to 4 groups for a 10-week study. One group performed twice-weekly SIT sessions on a cycle ergometer while maintaining body weight (SIT). A second group did not perform SIT but intentionally reduced body weight (WR). A third group simultaneously performed SIT sessions and reduced body weight (SIT+WR). A control group cycled in their normal routine and maintained body weight (CON). The 30-second Wingate Test assessed pretest and posttest POan:Wt scores. There was a significant mean increase (p weight (kg) decreased significantly in WR and SIT + WR (80.3 +/- 13.7 to 75.3 +/- 11.9 and 78.9 +/- 10.8 to 73.4 +/- 10.8, respectively). The results demonstrate that cyclists can use SIT sessions and body weight reduction as singular training interventions to effect significant increases in anaerobic power to weight ratio, which has been correlated to enhanced aerobic cycling performance. However, the treatments were not effective as combined interventions, as there was no significant change in either PPOan:Wt or APOan:Wt in SIT + WR.

  13. Mars Relay Satellite: Key to Enabling Low-Cost Exploration Missions

    Science.gov (United States)

    Hastrup, R.; Cesarone, R.; Miller, A.

    1993-01-01

    Recently, there has been increasing evidence of a renewed focus on Mars exploration both by NASA and the international community. The thrust of this renewed interest appears to be manifesting itself in numerous low-cost missions employing small, light weight elements, which utilize advanced technologies including integrated microelectronics. A formidable problem facing these low-cost missions is communications with Earth. Providing adequate direct-link performance has very significant impacts on spacecraft power, pointing, mass and overall complexity. Additionally, for elements at or near the surface of Mars, there are serious connectivity constraints, especially at higher latitudes, which lose view of Earth for up to many months at a time. This paper will discuss the role a Mars relay satellite can play in enabling and enhancing low-cost missions to Mars...

  14. Cost-optimal levels of minimum energy performance requirements in the Danish Building Regulations

    Energy Technology Data Exchange (ETDEWEB)

    Aggerholm, S.

    2013-09-15

    The purpose of the report is to analyse the cost optimality of the energy requirements in the Danish Building Regulations 2010, BR10 to new building and to existing buildings undergoing major renovation. The energy requirements in the Danish Building Regulations have by tradition always been based on the cost and benefits related to the private economical or financial perspective. Macro economical calculations have in the past only been made in addition. The cost optimum used in this report is thus based on the financial perspective. Due to the high energy taxes in Denmark there is a significant difference between the consumer price and the macro economical for energy. Energy taxes are also paid by commercial consumers when the energy is used for building operation e.g. heating, lighting, ventilation etc. In relation to the new housing examples the present minimum energy requirements in BR 10 all shows gaps that are negative with a deviation of up till 16 % from the point of cost optimality. With the planned tightening of the requirements to new houses in 2015 and in 2020, the energy requirements can be expected to be tighter than the cost optimal point, if the costs for the needed improvements don't decrease correspondingly. In relation to the new office building there is a gap of 31 % to the point of cost optimality in relation to the 2010 requirement. In relation to the 2015 and 2020 requirements there are negative gaps to the point of cost optimality based on today's prices. If the gaps for all the new buildings are weighted to an average based on mix of building types and heat supply for new buildings in Denmark there is a gap of 3 % in average for the new building. The excessive tightness with today's prices is 34 % in relation to the 2015 requirement and 49 % in relation to the 2020 requirement. The component requirement to elements in the building envelope and to installations in existing buildings adds up to significant energy efficiency

  15. Comparison of Cloud vs. Tape Backup Performance and Costs with Oracle Database

    OpenAIRE

    Zrnec, Aljaž; Lavbič, Dejan

    2011-01-01

    Current practice of backing up data is based on using backup tapes and remote locations for storing data. Nowadays, with the advent of cloud computing a new concept of database backup emerges. The paper presents the possibility of making backup copies of data in the cloud. We are mainly focused on performance and economic issues of making backups in the cloud in comparison to traditional backups. We tested the performance and overall costs of making backup copies of data in Ora...

  16. Perceived Physician-informed Weight Status Predicts Accurate Weight Self-Perception and Weight Self-Regulation in Low-income, African American Women.

    Science.gov (United States)

    Harris, Charlie L; Strayhorn, Gregory; Moore, Sandra; Goldman, Brian; Martin, Michelle Y

    2016-01-01

    Obese African American women under-appraise their body mass index (BMI) classification and report fewer weight loss attempts than women who accurately appraise their weight status. This cross-sectional study examined whether physician-informed weight status could predict weight self-perception and weight self-regulation strategies in obese women. A convenience sample of 118 low-income women completed a survey assessing demographic characteristics, comorbidities, weight self-perception, and weight self-regulation strategies. BMI was calculated during nurse triage. Binary logistic regression models were performed to test hypotheses. The odds of obese accurate appraisers having been informed about their weight status were six times greater than those of under-appraisers. The odds of those using an "approach" self-regulation strategy having been physician-informed were four times greater compared with those using an "avoidance" strategy. Physicians are uniquely positioned to influence accurate weight self-perception and adaptive weight self-regulation strategies in underserved women, reducing their risk for obesity-related morbidity.

  17. Costs of biodiesel supply chain in Latvia

    International Nuclear Information System (INIS)

    Birzietis, G.; Kunkule, D.

    2003-01-01

    Biodiesels has already become reality in Latvia, but still not are extensively used due to number of reasons. Cost reduction would be one of the most efficient tools that could encourage wider use of biodiesel. Identifying costs in biodiesel supply chain and evaluating their weight in total cost of final product is the first step to finding most costly elements and potential for cost reduction. General cost breakdown in final price is calculated and analysed in this study (authors)

  18. Overall performance assessment of a combined cycle power plant: An exergo-economic analysis

    International Nuclear Information System (INIS)

    Sahin, Ahmet Z.; Al-Sharafi, Abdullah; Yilbas, Bekir S.; Khaliq, Abdul

    2016-01-01

    Highlights: • An exergo-economic analysis is carried out for a combined cycle power plant. • An overall performance index (OPI) is defined to analyze the power plant. • Four performance indicators and three scenarios are considered in the analysis. • The optimum configuration of the power plant differs for each scenarios considered. - Abstract: An exergo-economic analysis is carried out for a combined cycle power plant using the first law and the second law of thermodynamics, and the economic principles while incorporating GT PRO/PEACE Software Packages. An overall performance index (OPI) is defined to assess and analyze the optimum operational and design configurations of the power plant. Four performance indicators are considered for the analysis; namely, energy efficiency (ENE), exergy efficiency (EXE), levelized cost of electricity (COE), and the total investment (TI) cost. Three possible scenarios are considered in which different weight factor is assigned to the performance indicators when assessing the performance. These scenarios are: (i) the conventional case in which the levelized cost of electricity is given a high priority, (ii) environmental conscious case in which the exergy efficiency is given a high priority, and (iii) the economical case in which the total cost of investment is given a high priority. It is shown that the optimum size and the configuration of the power plant differ for each scenarios considered. The selection and optimization of the size and configuration of the power plant are found to be depending on the user priorities and the weight factors assigned to the performance indicators.

  19. 42 CFR 412.60 - DRG classification and weighting factors.

    Science.gov (United States)

    2010-10-01

    ... DRG classification system provides a DRG, and an appropriate weighting factor, for the group of cases... 42 Public Health 2 2010-10-01 2010-10-01 false DRG classification and weighting factors. 412.60... Determining Prospective Payment Federal Rates for Inpatient Operating Costs § 412.60 DRG classification and...

  20. Managerial performance and cost efficiency of Japanese local public hospitals: a latent class stochastic frontier model.

    Science.gov (United States)

    Besstremyannaya, Galina

    2011-09-01

    The paper explores the link between managerial performance and cost efficiency of 617 Japanese general local public hospitals in 1999-2007. Treating managerial performance as unobservable heterogeneity, the paper employs a panel data stochastic cost frontier model with latent classes. Financial parameters associated with better managerial performance are found to be positively significant in explaining the probability of belonging to the more efficient latent class. The analysis of latent class membership was consistent with the conjecture that unobservable technological heterogeneity reflected in the existence of the latent classes is related to managerial performance. The findings may support the cause for raising efficiency of Japanese local public hospitals by enhancing the quality of management. Copyright © 2011 John Wiley & Sons, Ltd.

  1. Structural optimization procedure of a composite wind turbine blade for reducing both material cost and blade weight

    Science.gov (United States)

    Hu, Weifei; Park, Dohyun; Choi, DongHoon

    2013-12-01

    A composite blade structure for a 2 MW horizontal axis wind turbine is optimally designed. Design requirements are simultaneously minimizing material cost and blade weight while satisfying the constraints on stress ratio, tip deflection, fatigue life and laminate layup requirements. The stress ratio and tip deflection under extreme gust loads and the fatigue life under a stochastic normal wind load are evaluated. A blade element wind load model is proposed to explain the wind pressure difference due to blade height change during rotor rotation. For fatigue life evaluation, the stress result of an implicit nonlinear dynamic analysis under a time-varying fluctuating wind is converted to the histograms of mean and amplitude of maximum stress ratio using the rainflow counting algorithm Miner's rule is employed to predict the fatigue life. After integrating and automating the whole analysis procedure an evolutionary algorithm is used to solve the discrete optimization problem.

  2. A comparative analysis of performance and cost metrics associated with a diesel to biodiesel fleet transition

    International Nuclear Information System (INIS)

    Shrake, Scott O.; Landis, Amy E.; Bilec, Melissa M.; Collinge, William O.; Xue Xiaobo

    2010-01-01

    With energy security, economic stabilization, and environmental sustainability being at the forefront of US policy making, the development of biodiesel production and use within the United States has been growing at an astonishing rate. According to the latest DOE energy report, biodiesel production and consumption in the US has decreased since its peak in 2008, but still remains an important factor in the US energy mix. However, despite recent studies showing that B5 has similar performance qualities to that of the currently used ultra-low-sulfur petroleum diesel (ULSD) fleet managers and corporations still remain hesitant regarding a switch to B5. This research examined the major areas of concern that arise with transitioning fleets from ULSD to B5 with the goal of alleviating those concerns with quantitative results from an actual fleet implementation and transition. In conjunction with the Pennsylvania Department of Transportation (PennDOT) a comparison of cost, cold weather fuel properties, engine performance, fuel economy, and maintenance and repairs was conducted using data obtained over 3 years from a pilot study. The results found that B5 performed as well or better than ULSD in all performance metrics. - Research Highlights: →Conducted multi-year study of a DOT fleet transition from ULSD to biodiesel (B5)→No significant difference in cold weather performance, engine power output, or torque→No significant difference in fuel economy→No resulting increase in maintenance and repair costs or frequency→Life-cycle costing revealed no hidden costs as a result of B5 implementation

  3. Effects of Body Weight and Condition Changes After Parturition on the Reproductive Performance of Sahiwal and Friesian Cattle

    International Nuclear Information System (INIS)

    Indetie, D.E.; Indetie, A.; Kinywa, J.; Lukibisi, F; Musalia, L.; Bebe, B.; Wathuta, E.

    2015-01-01

    Nutrition has a profound influence on reproductive performance after parturition. Cows are in a typical state of negative energy balance, because nutritional requirements for milk production and maintenance of body function exceed that ingested from the feed. This is reflected by changes in body weight and condition postpartum which influence resumption of ovarian activity. The study objectives were to assess weight and body condition changes after parturition and their influence on reproductive performance of Sahiwal and Friesian lactating cows. Forty in-calf cows comprising 20 Friesians and Sahiwals were selected and upon calving, observed for 24 weeks postpartum. Parameters recorded were weekly live weight and body condition scores postpartum while reproductive attributes included days to commencement of luteal activity and insemination. Data was analyzed using GLM of SAS. There were breed differences in weight of cows at the start of the experiment with Friesians being heavier than Sahiwals. Friesians lost a mean of 31.2 Kg from calving to commencement of luteal activity which occurred 10 weeks postpartum and improved from this loss to register a deficit of 11.3 kg at insemination which occurred 14 weeks after calving while the Sahiwals lost a mean of 27 kg after 6 weeks postpartum at commencement of luteal activity and a further 8 kg to insemination occurring 10 weeks after calving. The mean weight loss for Friesians from calving to commencement of luteal activity was 0.45 kg/day while that of Sahiwals was 0.64 kg/day. The relative weight loss was 6 and 7% for Friesians and Sahiwals respectively. The mean body condition loss for the two breeds showed Sahiwals lost less body condition at commencement of luteal activity than Friesians (-0.19 vs -0.33) and resumed cyclicity earlier than Friesians which had better recovery rates from weight and body condition depression postpartum. This shows that Friesians lose weight rapidly and quickly recover at time of

  4. Controlling Capital Costs in High Performance Office Buildings: A Review of Best Practices for Overcoming Cost Barriers

    Energy Technology Data Exchange (ETDEWEB)

    Pless, S.; Torcellini, P.

    2012-05-01

    This paper presents a set of 15 best practices for owners, designers, and construction teams of office buildings to reach high performance goals for energy efficiency, while maintaining a competitive budget. They are based on the recent experiences of the owner and design/build team for the Research Support Facility (RSF) on National Renewable Energy Facility's campus in Golden, CO, which show that achieving this outcome requires each key integrated team member to understand their opportunities to control capital costs.

  5. Weight Status in Persons with Multiple Sclerosis: Implications for Mobility Outcomes

    Science.gov (United States)

    Pilutti, Lara A.; Dlugonski, Deirdre; Pula, John H.; Motl, Robert W.

    2012-01-01

    The accumulation of excess body weight may have important health and disease consequences for persons with multiple sclerosis (MS). This study examined the effect of weight status on mobility using a comprehensive set of mobility outcomes including ambulatory performance (timed 25-foot walk, T25FW; 6-minute walk, 6MW; oxygen cost of walking, Cw; spatiotemporal parameters of gait; self-reported walking impairment, Multiple Sclerosis Walking Scale-12 (MSWS-12); and free-living activity, accelerometry) in 168 ambulatory persons with MS. Mean (SD) BMI was 27.7 (5.1) kg/m2. Of the 168 participants, 31.0% were classified as normal weight (BMI = 18.5–24.9 kg/m2), 36.3% were classified as overweight (BMI = 25.0–29.9 kg/m2), and 32.7% were classified as obese, classes I and II (BMI = 30–39.9 kg/m2). There were no significant differences among BMI groups on T25FW and 6MW, Cw, spatiotemporal gait parameters, MSWS-12, or daily step and movement counts. The prevalence of overweight and obesity in this sample was almost 70%, but there was not a consistent nor significant impact of BMI on outcomes of mobility. The lack of an effect of weight status on mobility emphasizes the need to focus on and identify other factors which may be important targets of ambulatory performance in persons with MS. PMID:23050129

  6. Non-clairvoyant weighted flow time scheduling with rejection penalty

    DEFF Research Database (Denmark)

    Chan, Ho-Leung; Chan, Sze-Hang; Lam, Tak-Wah

    2012-01-01

    is defined as the weighted flow time of the job plus the penalty if it is rejected before completion. Previous work on minimizing the total user cost focused on the clairvoyant single-processor setting [BBC+03,CLL11] and has produced O(1)-competitive online algorithm for jobs with arbitrary weights...... algorithm has to decide job rejection and determine the order and speed of job execution. It is interesting to study the tradeoff between the above-mentioned user cost and energy. This paper gives two O(1)-competitive non-clairvoyant algorithms for minimizing the user cost plus energy on a single processor......This paper initiates the study of online scheduling with rejection penalty in the non-clairvoyant setting, i.e., the size (processing time) of a job is not assumed to be known at its release time. In the rejection penalty model, jobs can be rejected with a penalty, and the user cost of a job...

  7. Comparing the Mass, Energy, and Cost Effects of Lightweighting in Conventional and Electric Passenger Vehicles

    Directory of Open Access Journals (Sweden)

    Johannes Hofer

    2014-09-01

    Full Text Available In this work the effect of weight reduction using advanced lightweight materials on the mass, energy use, and cost of conventional and battery electric passenger vehicles is compared. Analytic vehicle simulation is coupled with cost assessment to find the optimal degree of weight reduction minimizing manufacturing and total costs. The results show a strong secondary weight and cost saving potential for the battery electric vehicles, but a higher sensitivity of vehicle energy use to mass reduction for the conventional vehicle. Generally, light weighting has the potential to lower vehicle costs, however, the results are very sensitive to parameters affecting lifetime fuel costs for conventional and battery costs for electric vehicles. Based on current technology cost estimates it is shown that the optimal amount of primary mass reduction minimizing total costs is similar for conventional and electric vehicles and ranges from 22% to 39%, depending on vehicle range and overall use patterns. The difference between the optimal solutions minimizing manufacturing versus total costs is higher for conventional than battery electric vehicles.

  8. Japanese manufacturers' cost-performance marketing strategy for the delivery of solar photovoltaic homes

    Energy Technology Data Exchange (ETDEWEB)

    Noguchi, M.

    2005-02-01

    Japanese manufacturers have been gaining a global reputation for their design approaches to industrialized housing, which is often equipped with PV systems. Homes are produced on a cost performance marketing strategy. In 2004, 13.7 per cent of the 1,160,083 houses built in Japan were pre-fabricated. The pre-fabricated housing industry has been given considerable government support. In response to growing demands for sustainable housing, the government has implemented promotional programs aiming to support the installations of photovoltaic systems. Details of various programs were presented, including: value-added production; housing sustainability; PV rooftop systems; and a mass custom design approach. It was concluded that the cost performance marketing strategy has a significant impact on production and design approaches. However, quality-oriented production may also result in successful commercialization of innovative housing. The Japanese marketing approach allows consumers to understand the added value of packaged innovations rather than the cost. It was suggested that this marketing strategy should be examined further, when considering approaches to innovative housing in other countries. 38 refs., 3 figs.

  9. Comparing the Mass, Energy, and Cost Effects of Lightweighting in Conventional and Electric Passenger Vehicles

    OpenAIRE

    Hofer, Johannes; Wilhelm, Erik; Schenler, Warren

    2014-01-01

    In this work the effect of weight reduction using advanced lightweight materials on the mass, energy use, and cost of conventional and battery electric passenger vehicles is compared. Analytic vehicle simulation is coupled with cost assessment to find the optimal degree of weight reduction minimizing manufacturing and total costs. The results show a strong secondary weight and cost saving potential for the battery electric vehicles, but a higher sensitivity of vehicle energy use to mass reduc...

  10. 45 CFR 2522.540 - Do the costs of performance measurement or evaluation count towards the statutory cap on...

    Science.gov (United States)

    2010-10-01

    ... evaluation count towards the statutory cap on administrative costs? 2522.540 Section 2522.540 Public Welfare... measurement or evaluation count towards the statutory cap on administrative costs? No, the costs of performance measurement and evaluation do not count towards the statutory five percent cap on administrative...

  11. Effect of feed texture on growth performance, dressing percentage and organ weight of broilers

    International Nuclear Information System (INIS)

    Mahmood, S.; Altaf, H.; Hassan, M.M.U.

    2013-01-01

    Comparative efficacy of two important forms of feed, mash and crumbles, fed alone or in combination (mash-crumbs), was studied on growth performance, dressing percentage and organ weight of broilers. One hundred twenty broiler chicks were used in the present study and were fed mash, crumbles and mash-crumbs feed for 0-6 weeks of age. Four treatments, designated as A, B, C and D were used in this experiment. Chicks in group A were kept on mash feeding serving as control and those in group B were offered crumbles. Group C was fed mash from day old to two weeks and crumbles from three to six weeks of age while group D was offered mash from day old to four weeks and then crumbles were fed for next two weeks of age. The results of the experiment showed that different forms of feed exhibited significant (P<0.05) effect on overall weight gain and feed conversion ratio (FCR) of the broilers. Whereas, feed consumption, dressing percentage and relative weights of liver, heart, gizzard, spleen, pancreas, intestine and abdominal fat pad of the birds remained unaffected due to different forms of feed. The broilers maintained upon crumbles throughout the experimental period, fetched maximum profit than other treatment groups. (author)

  12. Executive functions predict weight loss in a medically supervised weight loss programme

    Science.gov (United States)

    Bond, D.; Gunstad, J.; Pera, V.; Rathier, L.; Tremont, G.

    2016-01-01

    Summary Background Deficits in executive functions are related to poorer weight loss after bariatric surgery; however, less is known about the role that these deficits may play during participation in nonsurgical weight loss programmes. This study examined associations between objectively measured executive functions and weight loss during participation in a medically supervised weight loss programme. Methods Twenty‐three adult patients (age 50.4 ± 15.1, BMI 44.2 ± 8.8, 68% female, 92% White) enrolled in a medically supervised weight loss programme, involving prescription of a very low calorie diet and strategies to change eating and activity behaviours, underwent comprehensive computerized testing of executive functions at baseline. Weight was obtained at baseline and 8 weeks. Demographic and clinical information were obtained through medical chart review. Results Participants lost an average of 9.8 ± 3.4% of their initial body weight at 8 weeks. Fewer correct responses on a set‐shifting task and faster reaction time on a response inhibition task were associated with lower weight loss percentage at 8 weeks after adjusting for age, education and depressive symptoms. There were no associations between performance on tests of working memory or planning and weight loss. Conclusions This study shows that worse performance on a set‐shifting task (indicative of poorer cognitive flexibility) and faster reaction times on a response inhibition test (indicative of higher impulsivity) are associated with lower weight loss among participants in a medically supervised weight loss programme. Pre‐treatment assessment of executive functions may be useful in identifying individuals who may be at risk for suboptimal treatment outcomes. Future research is needed to replicate these findings in larger samples and identify underlying mechanisms. PMID:28090338

  13. Performance and cost results from a DOE Micro-CHP demonstration facility at Mississippi State University

    International Nuclear Information System (INIS)

    Giffin, Paxton K.

    2013-01-01

    Highlights: ► We examine the cost and performance results of a Micro-CHP demonstration facility. ► Evaluation includes both summer and winter performance. ► Evaluation in comparison to a conventional HVAC system using grid power. ► Influence of improperly sized equipment. ► Influence of natural gas prices on the viability of CHP projects using that fuel. - Abstract: Cooling, Heating, and Power (CHP) systems have been around for decades, but systems that utilize 20 kW or less, designated as Micro-CHP, are relatively new. A demonstration site has been constructed at Mississippi State University (MSU) to show the advantages of these micro scale systems. This study is designed to evaluate the performance of a Micro-CHP system as opposed to a conventional high-efficiency Heating, Ventilation, and Air Conditioning (HVAC) system that utilizes electrical power from the existing power grid. Raw data was collected for 7 months to present the following results. The combined cycle efficiency from the demonstration site was averaged at 29%. The average combined boiler and engine cost was $1.8 h −1 of operation for heating season and $3.9 h −1 of operation for cooling season. The cooling technology used, an absorption chiller exhibited an average Coefficient of Performance (COP) of 0.27. The conventional high-efficiency system, during cooling season, had a COP of 4.7 with a combined cooling and building cost of $0.2 h −1 of operation. During heating mode, the conventional system had an efficiency of 47% with a fuel and building electrical cost of $0.28 h −1 of operation.

  14. Pounds That Kill: The External Costs of Vehicle Weight

    OpenAIRE

    Michael L. Anderson; Maximilian Auffhammer

    2014-01-01

    Heavier vehicles are safer for their own occupants but more hazardous for the occupants of other vehicles. In this paper we estimate the increased probability of fatalities from being hit by a heavier vehicle in a collision. We show that, controlling for own-vehicle weight, being hit by a vehicle that is 1,000 pounds heavier results in a 47% increase in the baseline fatality probability. Estimation results further suggest that the fatality risk is even higher if the striking vehicle is a ligh...

  15. Inulin in Medicinal Plants (IV) : Reversed-Phase High-Performance Liquid Chromatography of Inulin after Acetylation : Molecular-Weight Distribution of Inulin in Medicinal Plants

    OpenAIRE

    三野, 芳紀; 筒井, 聡美; 太田, 長世; YOSHIKI, MINO; SATOMI, TSUTSUI; NAGAYO, OTA; 大阪薬科大学; 大阪薬科大学; 大阪薬科大学; Osaka College of Pharmacy; Osaka College of Pharmacy; Osaka College of Pharmacy

    1985-01-01

    Reversed-phase high-performance liquid chromatography coupled with pre-acetylation enabled acculate molecular-weight assay of inulin in medicinal plants to be conducted. The results clearly showed that the molecular-weight distribution of inulin varied depending on the stage of growth: Small molecular weight inulin polymers were detected in large quantity in the earlier growth stage whereas large molecular weight inulin polymers at the flowering and post flowering period.

  16. Comparison of costs and outcomes of dapagliflozin with other glucose-lowering therapy classes added to metformin using a short-term cost-effectiveness model in the US setting.

    Science.gov (United States)

    Chakravarty, Abhiroop; Rastogi, Mohini; Dhankhar, Praveen; Bell, Kelly F

    2018-05-01

    To compare 1-year costs and benefits of dapagliflozin (DAPA), a sodium-glucose cotransporter-2 (SGLT-2) inhibitor, with those of other treatments for type 2 diabetes (T2D), such as glucagon-like peptide-1 receptor agonists (GLP-1RAs), sulfonylureas (SUs), thiazolidinediones (TZDs), and dipeptidyl peptidase-4 inhibitors (DPP-4i), all combined with metformin. A short-term decision-analytic model with a 1-year time horizon was developed from a payer's perspective in the United States setting. Costs and benefits associated with four clinical end-points (glycated hemoglobin [A1C], body weight, systolic blood pressure [SBP], and risk of hypoglycemia) were evaluated in the analysis. The impact of DAPA and other glucose-lowering therapy classes on these clinical end-points was estimated from a network meta-analysis (NMA). Data for costs and quality-adjusted life-years (QALYs) associated with a per-unit change in these clinical end-points were taken from published literature. Drug prices were taken from an annual wholesale price list. All costs were inflation-adjusted to December 2016 costs using the medical care component of the consumer price index. Total costs (both medical and drug costs), total QALYs, and incremental cost-effectiveness ratios (ICERs) were estimated. Sensitivity analyses (SA) were performed to explore uncertainty in the inputs. To assess face validity, results from the short-term model were compared with long-term models published for these drugs. The total annual medical cost for DAPA was less than that for GLP-1RA ($186 less), DPP-4i ($1,142 less), SU ($2,474 less), and TZD ($1,640 less). Treatment with DAPA resulted in an average QALY gain of 0.0107, 0.0587, 0.1137, and 0.0715 per treated patient when compared with GLP-1RA, DPP-4i, SU, and TZD, respectively. ICERs for DAPA vs SU and TZD were $19,005 and $25,835, respectively. DAPA was a cost-saving option when compared with GLP-1RAs and DPP-4is. Among all four clinical end-points, change in weight

  17. Tackling obesity in areas of high social deprivation: clinical effectiveness and cost-effectiveness of a task-based weight management group programme - a randomised controlled trial and economic evaluation.

    Science.gov (United States)

    McRobbie, Hayden; Hajek, Peter; Peerbux, Sarrah; Kahan, Brennan C; Eldridge, Sandra; Trépel, Dominic; Parrott, Steve; Griffiths, Chris; Snuggs, Sarah; Myers Smith, Katie

    2016-10-01

    An increasing number of people require help to manage their weight. The NHS recommends weight loss advice by general practitioners and/or a referral to a practice nurse. Although this is helpful for some, more effective approaches that can be disseminated economically on a large scale are needed. To assess whether or not a task-based weight management programme [Weight Action Programme (WAP)] has better long-term effects than a 'best practice' intervention provided in primary care by practice nurses. Randomised controlled trial with cost-effectiveness analysis. General practices in east London, UK. Three hundred and thirty adults with a body mass index (BMI) of ≥ 30 kg/m 2 or a BMI of ≥ 28 kg/m 2 plus comorbidities were recruited from local general practices and via media publicity. Those who had a BMI of > 45 kg/m 2 , had lost > 5% of their body weight in the previous 6 months, were currently pregnant or taking psychiatric medications were excluded. Participants were randomised (2 : 1) to the WAP or nurse arms. The WAP intervention was delivered in eight weekly group sessions that combined dietary and physical activity, advice and self-monitoring in a group-oriented intervention. The initial course was followed by 10 monthly group maintenance sessions open to all participants in this study arm. The practice nurse intervention (best usual care) consisted of four one-to-one sessions delivered over 8 weeks, and included standard advice on diet and physical activity based on NHS 'Change4Life' materials and motivational support. The primary outcome measure was weight change at 12 months. Secondary outcome measures included change in BMI, waist circumference and blood pressure, and proportion of participants losing at least 5% and 10% of baseline body weight. Staff collecting measurements at the 6- and 12-month follow-ups were blinded to treatment allocation. The primary outcome measure was analysed according to the intention-to-treat principle

  18. Implementasi Perbandingan Metode Simple Additive Weighting Dengan Weighted Sum Model Dalam Pemilihan Siswa Berprestasi

    OpenAIRE

    Siregar, M. Fajrul Falah

    2015-01-01

    Good Performance Student Selection Program of MIN Tanjung Sari aims to increase students interest in learning. The selection is based on determined criterion. To assist the selection process, then a decision support system is needed. The method used is Simple Additive Weighting and Weighted Sum Model. In this research the results of both methods performed will be tested with the three periods of good performance students data possessed by MIN Tanjung Sari Medan Selayang. This s...

  19. Structural and performance costs of reproduction in a pure capital breeder, the Children's python Antaresia childreni.

    Science.gov (United States)

    Lourdais, Olivier; Lorioux, Sophie; DeNardo, Dale F

    2013-01-01

    Females often manage the high energy demands associated with reproduction by accumulating and storing energy in the form of fat before initiating their reproductive effort. However, fat stores cannot satisfy all reproductive resource demands, which include considerable investment of amino acids (e.g., for the production of yolk proteins or gluconeogenesis). Because capital breeders generally do not eat during reproduction, these amino acids must come from internal resources, typically muscle proteins. Although the energetic costs of reproduction have been fairly well studied, there are limited data on structural and performance costs associated with the muscle degradation required to meet amino acid demands. Thus, we examined structural changes (epaxial muscle width) and performance costs (constriction and strength) over the course of reproduction in a pure capital breeder, the children's python (Antaresia childreni). We found that both egg production (i.e., direct resource allocation) and maternal care (egg brooding) induce muscle catabolism and affect performance of the female. Although epaxial muscle loss was minimal in nonreproductive females, it reached up to 22% (in females after oviposition) and 34% (in females after brooding) of initial muscle width. Interestingly, we found that individuals with higher initial muscular condition allocated more of their muscle into reproduction. The amount of muscle loss was significantly linked to clutch mass, underscoring the role of structural protein in egg production. Egg brooding significantly increased proteolysis and epaxial loss despite no direct allocation to the offspring. Muscle loss was linked to a significant reduction in performance in postreproductive females. Overall, these results demonstrate that capital-breeding females experience dramatic costs that consume structural resources and jeopardize performance.

  20. Advanced Low-Cost O2/H2 Engines for the SSTO Application

    Science.gov (United States)

    Goracke, B. David; Levack, Daniel J. H.; Nixon, Robert F.

    1994-01-01

    The recent NASA Access to Space study examined future Earth to orbit (ETO) transportation needs and fleets out to 2030. The baseline in the option 3 assessment was a single stage to orbit (SSTO) vehicle. A study was conducted to assess the use of new advanced low cost O2/H2 engines for this SSTO application. The study defined baseline configurations and ground rules and defined six engine cycles to explore engine performance. The cycles included an open cycle, and a series of closed cycles with varying abilities to extract energy from the propellants to power he turbomachinery. The cycles thus varied in the maximum chamber pressure they could reach and in their weights at any given chamber pressure. The weight of each cycle was calculated for two technology levels versus chamber pressure up to the power limit of the cycle. The performance in the SSTO mission was then modeled using the resulting engine weights and specific impulse performance using the Access to Space option 3 vehicle. The results showed that new O2/H2 engines are viable and competitive candidates for the SSTO application using chamber pressures of 4,000 psi.

  1. Performance and cost characteristics of multi-electron transfer, common ion exchange non-aqueous redox flow batteries

    Science.gov (United States)

    Laramie, Sydney M.; Milshtein, Jarrod D.; Breault, Tanya M.; Brushett, Fikile R.; Thompson, Levi T.

    2016-09-01

    Non-aqueous redox flow batteries (NAqRFBs) have recently received considerable attention as promising high energy density, low cost grid-level energy storage technologies. Despite these attractive features, NAqRFBs are still at an early stage of development and innovative design techniques are necessary to improve performance and decrease costs. In this work, we investigate multi-electron transfer, common ion exchange NAqRFBs. Common ion systems decrease the supporting electrolyte requirement, which subsequently improves active material solubility and decreases electrolyte cost. Voltammetric and electrolytic techniques are used to study the electrochemical performance and chemical compatibility of model redox active materials, iron (II) tris(2,2‧-bipyridine) tetrafluoroborate (Fe(bpy)3(BF4)2) and ferrocenylmethyl dimethyl ethyl ammonium tetrafluoroborate (Fc1N112-BF4). These results help disentangle complex cycling behavior observed in flow cell experiments. Further, a simple techno-economic model demonstrates the cost benefits of employing common ion exchange NAqRFBs, afforded by decreasing the salt and solvent contributions to total chemical cost. This study highlights two new concepts, common ion exchange and multi-electron transfer, for NAqRFBs through a demonstration flow cell employing model active species. In addition, the compatibility analysis developed for asymmetric chemistries can apply to other promising species, including organics, metal coordination complexes (MCCs) and mixed MCC/organic systems, enabling the design of low cost NAqRFBs.

  2. Performance Of Growing Pigs And Finisher Broilers Housed Together

    African Journals Online (AJOL)

    Growth performance and cost of feeding young growing pigs and finisher broilers under integrated broiler/pig production system were investigated. Four young growing pigs (the control) were housed in pen A and fed 4% of their body weight as commercial growers feed. Another 4 were housed in pen B with broilers in ...

  3. Healthcare tariffs for specialist inpatient neurorehabilitation services: rationale and development of a UK casemix and costing methodology.

    Science.gov (United States)

    Turner-Stokes, Lynne; Sutch, Stephen; Dredge, Robert

    2012-03-01

    To describe the rationale and development of a casemix model and costing methodology for tariff development for specialist neurorehabilitation services in the UK. Patients with complex needs incur higher treatment costs. Fair payment should be weighted in proportion to costs of providing treatment, and should allow for variation over time CASEMIX MODEL AND BAND-WEIGHTING: Case complexity is measured by the Rehabilitation Complexity Scale (RCS). Cases are divided into five bands of complexity, based on the total RCS score. The principal determinant of costs in rehabilitation is staff time. Total staff hours/week (estimated from the Northwick Park Nursing and Therapy Dependency Scales) are analysed within each complexity band, through cross-sectional analysis of parallel ratings. A 'band-weighting' factor is derived from the relative proportions of staff time within each of the five bands. Total unit treatment costs are obtained from retrospective analysis of provider hospitals' budget and accounting statements. Mean bed-day costs (total unit cost/occupied bed days) are divided broadly into 'variable' and 'non-variable' components. In the weighted costing model, the band-weighting factor is applied to the variable portion of the bed-day cost to derive a banded cost, and thence a set of cost-multipliers. Preliminary data from one unit are presented to illustrate how this weighted costing model will be applied to derive a multilevel banded payment model, based on serial complexity ratings, to allow for change over time.

  4. Trouble Sleeping Associated With Lower Work Performance and Greater Health Care Costs: Longitudinal Data From Kansas State Employee Wellness Program.

    Science.gov (United States)

    Hui, Siu-kuen Azor; Grandner, Michael A

    2015-10-01

    To examine the relationships between employees' trouble sleeping and absenteeism, work performance, and health care expenditures over a 2-year period. Utilizing the Kansas State employee wellness program (EWP) data set from 2008 to 2009, multinomial logistic regression analyses were conducted with trouble sleeping as the predictor and absenteeism, work performance, and health care costs as the outcomes. EWP participants (N = 11,698 in 2008; 5636 followed up in 2009) who had higher levels of sleep disturbance were more likely to be absent from work (all P work performance ratings (all P health care costs (P work attendance, work performance, and health care costs.

  5. Selecting the correct weighting factors for linear and quadratic calibration curves with least-squares regression algorithm in bioanalytical LC-MS/MS assays and impacts of using incorrect weighting factors on curve stability, data quality, and assay performance.

    Science.gov (United States)

    Gu, Huidong; Liu, Guowen; Wang, Jian; Aubry, Anne-Françoise; Arnold, Mark E

    2014-09-16

    A simple procedure for selecting the correct weighting factors for linear and quadratic calibration curves with least-squares regression algorithm in bioanalytical LC-MS/MS assays is reported. The correct weighting factor is determined by the relationship between the standard deviation of instrument responses (σ) and the concentrations (x). The weighting factor of 1, 1/x, or 1/x(2) should be selected if, over the entire concentration range, σ is a constant, σ(2) is proportional to x, or σ is proportional to x, respectively. For the first time, we demonstrated with detailed scientific reasoning, solid historical data, and convincing justification that 1/x(2) should always be used as the weighting factor for all bioanalytical LC-MS/MS assays. The impacts of using incorrect weighting factors on curve stability, data quality, and assay performance were thoroughly investigated. It was found that the most stable curve could be obtained when the correct weighting factor was used, whereas other curves using incorrect weighting factors were unstable. It was also found that there was a very insignificant impact on the concentrations reported with calibration curves using incorrect weighting factors as the concentrations were always reported with the passing curves which actually overlapped with or were very close to the curves using the correct weighting factor. However, the use of incorrect weighting factors did impact the assay performance significantly. Finally, the difference between the weighting factors of 1/x(2) and 1/y(2) was discussed. All of the findings can be generalized and applied into other quantitative analysis techniques using calibration curves with weighted least-squares regression algorithm.

  6. Fractional-Fourier-domain weighted Wigner distribution

    NARCIS (Netherlands)

    Stankovic, L.; Alieva, T.; Bastiaans, M.J.

    2001-01-01

    A fractional-Fourier-domain realization of the weighted Wigner distribution (or S-method), producing auto-terms close to the ones in the Wigner distribution itself, but with reduced cross-terms, is presented. The computational cost of this fractional-domain realization is the same as the

  7. Epidemiological geomatics in evaluation of mine risk education in Afghanistan: introducing population weighted raster maps

    Directory of Open Access Journals (Sweden)

    Andersson Neil

    2006-01-01

    Full Text Available Abstract Evaluation of mine risk education in Afghanistan used population weighted raster maps as an evaluation tool to assess mine education performance, coverage and costs. A stratified last-stage random cluster sample produced representative data on mine risk and exposure to education. Clusters were weighted by the population they represented, rather than the land area. A "friction surface" hooked the population weight into interpolation of cluster-specific indicators. The resulting population weighted raster contours offer a model of the population effects of landmine risks and risk education. Five indicator levels ordered the evidence from simple description of the population-weighted indicators (level 0, through risk analysis (levels 1–3 to modelling programme investment and local variations (level 4. Using graphic overlay techniques, it was possible to metamorphose the map, portraying the prediction of what might happen over time, based on the causality models developed in the epidemiological analysis. Based on a lattice of local site-specific predictions, each cluster being a small universe, the "average" prediction was immediately interpretable without losing the spatial complexity.

  8. Monitoring household waste recycling centres performance using mean bin weight analyses.

    Science.gov (United States)

    Maynard, Sarah; Cherrett, Tom; Waterson, Ben

    2009-02-01

    This paper describes a modelling approach used to investigate the significance of key factors (vehicle type, compaction type, site design, temporal effects) in influencing the variability in observed nett amenity bin weights produced by household waste recycling centres (HWRCs). This new method can help to quickly identify sites that are producing significantly lighter bins, enabling detailed back-end analyses to be efficiently targeted and best practice in HWRC operation identified. Tested on weigh ticket data from nine HWRCs across West Sussex, UK, the model suggests that compaction technique, vehicle type, month and site design explained 76% of the variability in the observed nett amenity weights. For each factor, a weighting coefficient was calculated to generate a predicted nett weight for each bin transaction and three sites were subsequently identified as having similar characteristics but returned significantly different mean nett bin weights. Waste and site audits were then conducted at the three sites to try and determine the possible sources of the remaining variability. Significant differences were identified in the proportions of contained waste (bagged), wood, and dry recyclables entering the amenity waste stream, particularly at one site where significantly less contaminated waste and dry recyclables were observed.

  9. Total cost of performing analog-to-digital upgrades

    International Nuclear Information System (INIS)

    Albrigo, T.

    1993-01-01

    The financial well-being of nuclear power plants in the United States is dependent on reducing costs. Rapid advances in industrial technology have created a conundrum for utility executives and their engineering staffs. Digital technology is being touted as beneficial in many ways; however, a number of significant issues have been raised regarding the adequacy and financial viability of digital systems in nuclear power plants. Actual or perceived problems with digital system design, development, and installation have caused significant financial losses for nuclear utilities. This paper provides a list of problems that must be considered in performing an analog-to-digital conversion or for doing a large digital upgrade. It is desirable that the full financial risks associated with these types of upgrades are considered. Specific problems encountered at Palo Verde nuclear generating station are reviewed to emphasize some of the problem areas

  10. Design of a Multiobjective Reverse Logistics Network Considering the Cost and Service Level

    Directory of Open Access Journals (Sweden)

    Shuang Li

    2012-01-01

    Full Text Available Reverse logistics, which is induced by various forms of used products and materials, has received growing attention throughout this decade. In a highly competitive environment, the service level is an important criterion for reverse logistics network design. However, most previous studies about product returns only focused on the total cost of the reverse logistics and neglected the service level. To help a manufacturer of electronic products provide quality postsale repair service for their consumer, this paper proposes a multiobjective reverse logistics network optimisation model that considers the objectives of the cost, the total tardiness of the cycle time, and the coverage of customer zones. The Nondominated Sorting Genetic Algorithm II (NSGA-II is employed for solving this multiobjective optimisation model. To evaluate the performance of NSGA-II, a genetic algorithm based on weighted sum approach and Multiobjective Simulated Annealing (MOSA are also applied. The performance of these three heuristic algorithms is compared using numerical examples. The computational results show that NSGA-II outperforms MOSA and the genetic algorithm based on weighted sum approach. Furthermore, the key parameters of the model are tested, and some conclusions are drawn.

  11. Impact of automatic calibration techniques on HMD life cycle costs and sustainable performance

    Science.gov (United States)

    Speck, Richard P.; Herz, Norman E., Jr.

    2000-06-01

    Automatic test and calibration has become a valuable feature in many consumer products--ranging from antilock braking systems to auto-tune TVs. This paper discusses HMDs (Helmet Mounted Displays) and how similar techniques can reduce life cycle costs and increase sustainable performance if they are integrated into a program early enough. Optical ATE (Automatic Test Equipment) is already zeroing distortion in the HMDs and thereby making binocular displays a practical reality. A suitcase sized, field portable optical ATE unit could re-zero these errors in the Ready Room to cancel the effects of aging, minor damage and component replacement. Planning on this would yield large savings through relaxed component specifications and reduced logistic costs. Yet, the sustained performance would far exceed that attained with fixed calibration strategies. Major tactical benefits can come from reducing display errors, particularly in information fusion modules and virtual `beyond visual range' operations. Some versions of the ATE described are in production and examples of high resolution optical test data will be discussed.

  12. Performance Evaluation of Low Cost LoRa Modules in IoT Applications

    Science.gov (United States)

    Daud, Shuhaizar; Shi Yang, Teoh; Asmi Romli, Muhamad; Awang Ahmad, Zahari; Mahrom, Norfadila; Raof, Rafikha Aliana A.

    2018-03-01

    LoRa is a low power long range wireless communication platform that is designed as an efficient communication platform for small, low powered devices. This makes it very suitable for battery powered devices and IoT implementation. This paper evaluates some low cost LoRa modules available on the market and their suitability, energy efficiency and performance during operation. Two low cost LoRa transceiver from Semtech Industries, the SX1272 and SX1278 were tested for their power consumption and maximum transmission range. This study have evaluated the two LoRa solutions and found that the SX1278 have a better transmission range and uses lower energy compared to the SX1272 thus making it more suitable for embedded implementation as a data gateway.

  13. Comparative Effect of Diets Containing Cooked and Roasted Soybeans on Growth Performances of Growing Finishing Pigs

    Directory of Open Access Journals (Sweden)

    F. Meffeja

    2003-01-01

    Full Text Available heat of soybeans on the performances of grower-finisher pigs. Twenty hybrid male piglets, averaging 15.4 ± 0.8 kg initial body weights were allotted to four experimental diets (five replicates per treatment based on soybean meal, cotton seed cake, cooked or roasted soybeans over a 98-day period. The rations containing the commonly used soybean meal and cotton seed cake were used as control diets. Results showed that the weight gain and feed conversion ratio obtained with diets containing roasted and cooked soybeans were significantly (P 0.05 compared to the soybean meal diet. Comparison of the two methods of heat treatment showed no significant difference on animal performances. Feed costs to produce one kilogram live weight, calculated as mean costs for both growth phases, although not significant between treatments, showed a slightly lower value in roasted soybean diets. These results show that the roasting method can be used with the same advantages as the cooking method.

  14. Vehicle Design Evaluation Program (VDEP). A computer program for weight sizing, economic, performance and mission analysis of fuel-conservative aircraft, multibodied aircraft and large cargo aircraft using both JP and alternative fuels

    Science.gov (United States)

    Oman, B. H.

    1977-01-01

    The NASA Langley Research Center vehicle design evaluation program (VDEP-2) was expanded by (1) incorporating into the program a capability to conduct preliminary design studies on subsonic commercial transport type aircraft using both JP and such alternate fuels as hydrogen and methane;(2) incorporating an aircraft detailed mission and performance analysis capability; and (3) developing and incorporating an external loads analysis capability. The resulting computer program (VDEP-3) provides a preliminary design tool that enables the user to perform integrated sizing, structural analysis, and cost studies on subsonic commercial transport aircraft. Both versions of the VDEP-3 Program which are designated preliminary Analysis VDEP-3 and detailed Analysis VDEP utilize the same vehicle sizing subprogram which includes a detailed mission analysis capability, as well as a geometry and weight analysis for multibodied configurations.

  15. The cost of preventing undernutrition: cost, cost-efficiency and cost-effectiveness of three cash-based interventions on nutrition outcomes in Dadu, Pakistan.

    Science.gov (United States)

    Trenouth, Lani; Colbourn, Timothy; Fenn, Bridget; Pietzsch, Silke; Myatt, Mark; Puett, Chloe

    2018-07-01

    Cash-based interventions (CBIs) increasingly are being used to deliver humanitarian assistance and there is growing interest in the cost-effectiveness of cash transfers for preventing undernutrition in emergency contexts. The objectives of this study were to assess the costs, cost-efficiency and cost-effectiveness in achieving nutrition outcomes of three CBIs in southern Pakistan: a 'double cash' (DC) transfer, a 'standard cash' (SC) transfer and a 'fresh food voucher' (FFV) transfer. Cash and FFVs were provided to poor households with children aged 6-48 months for 6 months in 2015. The SC and FFV interventions provided $14 monthly and the DC provided $28 monthly. Cost data were collected via institutional accounting records, interviews, programme observation, document review and household survey. Cost-effectiveness was assessed as cost per case of wasting, stunting and disability-adjusted life year (DALY) averted. Beneficiary costs were higher for the cash groups than the voucher group. Net total cost transfer ratios (TCTRs) were estimated as 1.82 for DC, 2.82 for SC and 2.73 for FFV. Yet, despite the higher operational costs, the FFV TCTR was lower than the SC TCTR when incorporating the participation cost to households, demonstrating the relevance of including beneficiary costs in cost-efficiency estimations. The DC intervention achieved a reduction in wasting, at $4865 per case averted; neither the SC nor the FFV interventions reduced wasting. The cost per case of stunting averted was $1290 for DC, $882 for SC and $883 for FFV. The cost per DALY averted was $641 for DC, $434 for SC and $563 for FFV without discounting or age weighting. These interventions are highly cost-effective by international thresholds. While it is debatable whether these resource requirements represent a feasible or sustainable investment given low health expenditures in Pakistan, these findings may provide justification for continuing Pakistan's investment in national social safety

  16. Performance evaluation of direct methanol fuel cells for portable applications

    Energy Technology Data Exchange (ETDEWEB)

    Rashidi, R.; Dincer, I.; Naterer, G.F. [Faculty of Engineering and Applied Science, University of Ontario Institute of Technology, 2000 Simcoe Street North, Oshawa, Ontario (Canada); Berg, P. [Faculty of Science, University of Ontario Institute of Technology, 2000 Simcoe Street North, Oshawa, Ontario (Canada)

    2009-02-15

    This study examines the feasibility of powering a range of portable devices with a direct methanol fuel cell (DMFC). The analysis includes a comparison between a Li-ion battery and DMFC to supply the power for a laptop, camcorder and a cell phone. A parametric study of the systems for an operational period of 4 years is performed. Under the assumptions made for both the Li-ion battery and DMFC system, the battery cost is lower than the DMFC during the first year of operation. However, by the end of 4 years of operational time, the DMFC system would cost less. The weight and cost comparisons show that the fuel cell system occupies less space than the battery to store a higher amount of energy. The weight of both systems is almost identical. Finally, the CO{sub 2} emissions can be decreased by a higher exergetic efficiency of the DMFC, which leads to improved sustainability. (author)

  17. Design of Ultra High Performance Fiber Reinforced Concrete Shells

    DEFF Research Database (Denmark)

    Jepsen, Michael S.; Lambertsen, Søren Heide; Damkilde, Lars

    2013-01-01

    Fiber Reinforced Concrete shell. The major challenge in the design phase has been securing sufficient stiffness of the structure while keeping the weight at a minimum. The weight/stiffness issue has been investigated by means of the finite element method, to optimize the structure regarding overall......The paper treats the redesign of the float structure of the Wavestar wave energy converter. Previously it was designed as a glass fiber structure, but due to cost reduction requirements a redesign has been initiated. The new float structure will be designed as a double curved Ultra High Performance...

  18. An analysis of the relationship between cost, performance and structure of school units in the city of Cambé / PR

    Directory of Open Access Journals (Sweden)

    Marissa Yanara de Godoy Lima

    2017-08-01

    Full Text Available To government resources be earmarked for equality and just education for every society, it is important that public managers make decisions and measures that address this need and are more effective. Thus, there is the understanding that measuring education costs adequately, relating such costs to students' school performance is necessary for the definition that costs are used for educational development. Based on this premise, the article aims to analyze how possible relationships between costs, performance and structure of the different elementary school units in the city of Cambé / PR. This study was carried out from the analysis of the distribution of resources invested in primary education in a small municipality in the north of Paraná. For a data analysis, a descriptive statistic was used, as was the non-parametric correlation test. It was verified that the schools that obtained the highest cost / student did not necessarily present better performance in the indicators of quality of the Basic Education Development Index (IDEB, evidencing a significant asymmetry of the cost / student ratio existing among the schools surveyed.

  19. Produção de suínos inteiros com ou sem a suplementação de aminoácidos: desempenho e custo de alimento Production of entire male pigs with or without the supplementation of amino acids: performance and feed cost

    Directory of Open Access Journals (Sweden)

    Glauber Valentim Porolnik

    2012-02-01

    Full Text Available Um experimento foi realizado para avaliar o desempenho e o custo do alimento de suínos machos castrados e inteiros suplementados ou não com aminoácidos. Foram utilizados 48 animais com peso vivo inicial de 38,8±0,2kg, distribuídos num delineamento de blocos ao acaso em três tratamentos, sendo machos castrados (MC, machos inteiros (MI e MI suplementados com 5% de aminoácidos (MI+5%AA. Não houve efeito (P>0,05 dos tratamentos sobre o peso vivo e o ganho de peso dos suínos. O consumo de ração, a conversão alimentar e o custo do alimento diferiram (PAn experiment was carried out to evaluate the performance and feed cost of barrows and boars fed or not with amino acid supplemented diets. Forty-eight animals were used with initial weight of 38.8±0.2kg distributed in a randomized block design with three treatments, being barrows males (CM, boars males (IM and IM supplemented with 5% of amino acids (IM+5% AA. The treatment had no effect on body weight and weight gain. Feed intake, feed conversion ratio and feed cost were different (P<0.05 among treatments. Average feed intake was of 2.43kg, and the intake observed on CM (P<0.05 was higher at 5.5 and 5.2% in relation to IM and IM+5%AA, respectively. Feed conversion ratio was of 2.28, and the CM showed the worse conversion (P<0.05 at 6.2 and 11.6% in relation to IM and IM+5%AA, respectively. Average feed cost was of R$ 1,82kg-1, being higher (P<0.05 for the CM in relation to IM and IM+5%AA. The sex category (barrows or boars and amino acid supplementation did not affect body weight and weight gain, but alter feed intake, feed conversion ratio and feed cost.

  20. Entropy-Weighted Instance Matching Between Different Sourcing Points of Interest

    Directory of Open Access Journals (Sweden)

    Lin Li

    2016-01-01

    Full Text Available The crucial problem for integrating geospatial data is finding the corresponding objects (the counterpart from different sources. Most current studies focus on object matching with individual attributes such as spatial, name, or other attributes, which avoids the difficulty of integrating those attributes, but at the cost of an ineffective matching. In this study, we propose an approach for matching instances by integrating heterogeneous attributes with the allocation of suitable attribute weights via information entropy. First, a normalized similarity formula is developed, which can simplify the calculation of spatial attribute similarity. Second, sound-based and word segmentation-based methods are adopted to eliminate the semantic ambiguity when there is a lack of a normative coding standard in geospatial data to express the name attribute. Third, category mapping is established to address the heterogeneity among different classifications. Finally, to address the non-linear characteristic of attribute similarity, the weights of the attributes are calculated by the entropy of the attributes. Experiments demonstrate that the Entropy-Weighted Approach (EWA has good performance both in terms of precision and recall for instance matching from different data sets.

  1. Productive and Economic Performance of Broiler Chickens Subjected to Different Nutritional Plans

    Directory of Open Access Journals (Sweden)

    JMS Martins

    Full Text Available ABSTRACT The objective of the study was to evaluate the effect of nutritional plans on the productive and economic performance of Hubbard Flex broiler chickens. A completely randomized experimental design was applied, consisting of five treatments. Treatments consisted of five different nutritional plans: a basal diet containing the nutrient and energy levels recommended by literature and designated reference diet; two diets containing 1.5% and 3% lower levels than the reference diet; and two diets containing 1.5% and 3% higher levels than the reference diet (-3%, -1.5%, reference plan, +1.5% and +3%. Feed intake (FI, body weight (BW, feed conversion rate (FCR, livability (L and productive efficient index (PEI were determined when broilers were 42 days old. Broilers were processed, and carcass and parts (breast fillet, leg, and wings yields were determined. The economic viablility of the nutitional plans was evaluated as a function of feed cost/kg live and carcass weights, economic efficiency index (EEI, and cost index (CI. Feed intake and the feed conversion rate decreased as dietary nutrient and energy levels increased. Feed cost/kg live weight, economic efficiency index, and cost index cost increased as dietary nutrient and energy levels increased. Feed intake, feed conversion ratio, production efficiency index, and breast yield improved with increasing nutritional and energy levels. However, worse economic results were obtained with higher nutritional and energy levels.

  2. Designer's unified cost model

    Science.gov (United States)

    Freeman, William T.; Ilcewicz, L. B.; Swanson, G. D.; Gutowski, T.

    1992-01-01

    A conceptual and preliminary designers' cost prediction model has been initiated. The model will provide a technically sound method for evaluating the relative cost of different composite structural designs, fabrication processes, and assembly methods that can be compared to equivalent metallic parts or assemblies. The feasibility of developing cost prediction software in a modular form for interfacing with state of the art preliminary design tools and computer aided design programs is being evaluated. The goal of this task is to establish theoretical cost functions that relate geometric design features to summed material cost and labor content in terms of process mechanics and physics. The output of the designers' present analytical tools will be input for the designers' cost prediction model to provide the designer with a data base and deterministic cost methodology that allows one to trade and synthesize designs with both cost and weight as objective functions for optimization. The approach, goals, plans, and progress is presented for development of COSTADE (Cost Optimization Software for Transport Aircraft Design Evaluation).

  3. Risk-Assessment Score and Patient Optimization as Cost Predictors for Ventral Hernia Repair.

    Science.gov (United States)

    Saleh, Sherif; Plymale, Margaret A; Davenport, Daniel L; Roth, John Scott

    2018-04-01

    Ventral hernia repair (VHR) is associated with complications that significantly increase healthcare costs. This study explores the associations between hospital costs for VHR and surgical complication risk-assessment scores, need for cardiac or pulmonary evaluation, and smoking or obesity counseling. An IRB-approved retrospective study of patients having undergone open VHR over 3 years was performed. Ventral Hernia Risk Score (VHRS) for surgical site occurrence and surgical site infection, and the Ventral Hernia Working Group grade were calculated for each case. Also recorded were preoperative cardiology or pulmonary evaluations, smoking cessation and weight reduction counseling, and patient goal achievement. Hospital costs were obtained from the cost accounting system for the VHR hospitalization stratified by major clinical cost drivers. Univariate regression analyses were used to compare the predictive power of the risk scores. Multivariable analysis was performed to develop a cost prediction model. The mean cost of index VHR hospitalization was $20,700. Total and operating room costs correlated with increasing CDC wound class, VHRS surgical site infection score, VHRS surgical site occurrence score, American Society of Anesthesiologists class, and Ventral Hernia Working Group (all p variance in costs (p optimization significantly reduced direct and operating room costs (p < 0.05). Cardiac evaluation was associated with increased costs. Ventral hernia repair hospital costs are more accurately predicted by CDC wound class than VHR risk scores. A straightforward 6-factor model predicted most cost variation for VHR. Copyright © 2018 American College of Surgeons. Published by Elsevier Inc. All rights reserved.

  4. Weight Status and Differences in Mobility Performance, Pain Symptoms, and Physical Activity in Older, Knee Osteoarthritis Patients

    Directory of Open Access Journals (Sweden)

    Matthew J. Garver

    2014-01-01

    Full Text Available Knee osteoarthritis (OA is a leading cause of functional disability among American adults. Obesity is a strong independent risk factor for OA. While research emphasizes the role of obesity in the OA-physical function relationship, the extent to which weight status impacts salient physical, health, and pain measures in older, knee OA patients is not well delineated. The primary aim of this study was to assess differences in mobility performance (stair climb and 400-meter walk, mobility-related self-efficacy, pain symptoms (WOMAC, and measures of accelerometer-determined physical activity (PA as a function of weight status. Analysis of covariance was conducted to examine differences on the dependent variables. Obese class III patients were outperformed by their counterparts on nearly every measure of mobility, mobility-related self-efficacy, and the assessment of pain symptoms. These outcomes did not differ among other weight comparisons. Normal weight subjects outperformed classes I, II, and III counterparts on most measures of PA (engagement in moderate or greater PA and total weekly steps. Additionally, overweight participants outperformed obese class II participants and obese class I participants outperformed obese classes II and III participants on total weekly steps. Collectively, these findings underscore the meaningful differences observed in relevant OA outcomes as a function of increasing levels of body weight.

  5. Green Suppliers Performance Evaluation in Belt and Road Using Fuzzy Weighted Average with Social Media Information

    Directory of Open Access Journals (Sweden)

    Kuo-Ping Lin

    2017-12-01

    Full Text Available A decision model for selecting a suitable supplier is a key to reducing the environmental impact in green supply chain management for high-tech companies. Traditional fuzzy weight average (FWA adopts linguistic variable to determine weight by experts. However, the weights of FWA have not considered the public voice, meaning the viewpoints of consumers in green supply chain management. This paper focuses on developing a novel decision model for green supplier selection in the One Belt and One Road (OBOR initiative through a fuzzy weighted average approach with social media. The proposed decision model uses the membership grade of the criteria and sub-criteria and its relative weights, which consider the volume of social media, to establish an analysis matrix of green supplier selection. Then, the proposed fuzzy weighted average approach is considered as an aggregating tool to calculate a synthetic score for each green supplier in the Belt and Road initiative. The final score of the green supplier is ordered by a non-fuzzy performance value ranking method to help the consumer make a decision. A case of green supplier selection in the light-emitting diode (LED industry is used to demonstrate the proposed decision model. The findings demonstrate (1 the consumer’s main concerns are the “Quality” and “Green products” in LED industry, hence, the ranking of suitable supplier in FWA with social media information model obtained the difference result with tradition FWA; (2 OBOR in the LED industry is not fervently discussed in searches of Google and Twitter; and (3 the FWA with social media information could objectively analyze the green supplier selection because the novel model considers the viewpoints of the consumer.

  6. Development of simplified decommissioning cost estimation code for nuclear facilities

    International Nuclear Information System (INIS)

    Tachibana, Mitsuo; Shiraishi, Kunio; Ishigami, Tsutomu

    2010-01-01

    The simplified decommissioning cost estimation code for nuclear facilities (DECOST code) was developed in consideration of features and structures of nuclear facilities and similarity of dismantling methods. The DECOST code could calculate 8 evaluation items of decommissioning cost. Actual dismantling in the Japan Atomic Energy Agency (JAEA) was evaluated; unit conversion factors used to calculate the manpower of dismantling activities were evaluated. Consequently, unit conversion factors of general components could be classified into three kinds. Weights of components and structures of the facility were necessary for calculation of manpower. Methods for evaluating weights of components and structures of the facility were studied. Consequently, the weight of components in the facility was proportional to the weight of structures of the facility. The weight of structures of the facility was proportional to the total area of floors in the facility. Decommissioning costs of 7 nuclear facilities in the JAEA were calculated by using the DECOST code. To verify the calculated results, the calculated manpower was compared with the manpower gained from actual dismantling. Consequently, the calculated manpower and actual manpower were almost equal. The outline of the DECOST code, evaluation results of unit conversion factors, the evaluation method of the weights of components and structures of the facility are described in this report. (author)

  7. III-V/Active-Silicon Integration for Low-Cost High-Performance Concentrator Photovoltaics

    Energy Technology Data Exchange (ETDEWEB)

    Ringel, Steven [The Ohio State Univ., Columbus, OH (United States); Carlin, John A [The Ohio State Univ., Columbus, OH (United States); Grassman, Tyler [The Ohio State Univ., Columbus, OH (United States)

    2018-04-17

    This FPACE project was motivated by the need to establish the foundational pathway to achieve concentrator solar cell efficiencies greater than 50%. At such an efficiency, DOE modeling projected that a III-V CPV module cost of $0.50/W or better could be achieved. Therefore, the goal of this project was to investigate, develop and advance a III-V/Si mulitjunction (MJ) CPV technology that can simultaneously address the primary cost barrier for III-V MJ solar cells while enabling nearly ideal MJ bandgap profiles that can yield efficiencies in excess of 50% under concentrated sunlight. The proposed methodology was based on use of our recently developed GaAsP metamorphic graded buffer as a pathway to integrate unique GaAsP and Ga-rich GaInP middle and top junctions having bandgaps that are adjustable between 1.45 – 1.65 eV and 1.9 – 2.1 eV, respectively, with an underlying, 1.1 eV active Si subcell/substrate. With this design, the Si can be an active component sub-cell due to the semi-transparent nature of the GaAsP buffer with respect to Si as well as a low-cost alternative substrate that is amenable to scaling with existing Si foundry infrastructure, providing a reduction in materials cost and a low cost path to manufacturing at scale. By backside bonding of a SiGe, a path to exceed 50% efficiency is possible. Throughout the course of this effort, an expansive range of new understanding was achieved that has stimulated worldwide efforts in III-V/Si PV R&D that spanned materials development, metamorphic device optimization, and complete III-V/Si monolithic integration. Highlights include the demonstration of the first ideal GaP/Si interfaces grown by industry-standard MOCVD processes, the first high performance metamorphic tunnel junctions designed for III-V/Si integration, record performance of specific metamorphic sub-cell designs, the first fully integrated GaInP/GaAsP/Si double (1.7 eV/1.1 eV) and triple (1.95 eV/1.5 eV/1.1 eV) junction solar cells, the first

  8. Effect of mature body weight and stocking rate on cow and calf performance, cow herd efficiency, and economics in the southeastern United States.

    Science.gov (United States)

    Beck, P A; Stewart, C B; Gadberry, M S; Haque, M; Biermacher, J

    2016-04-01

    Eight 4-ha mixed warm-season grass pastures in southwestern Arkansas (33°40'4″ N, 93°35'24″ W, and elevation 107 m) were stocked with either large mature size (571 kg [SD 55.2] BW) or small mature size (463 kg [SD 58.2] BW) spring-calving cows at 4 stocking rates (SR; 1, 1.5, 2, or 2.5 cow-calf pairs/ha) over 4 yr to test the effects of SR and mature body size on cow and calf performance and system economics. Each pasture received 112 kg/ha N as ammonium nitrate in May and was broadcast seeded to annual ryegrass ( Lam.) in mid October each fall along with 112 kg/ha N as ammonium nitrate. Data were analyzed by regression to determine the effects of cow size and SR on calf performance, cow BW change, calf gain, weaning weight per hectare, hay feeding requirements, and net returns. As SR increased, cow BW and BCS at weaning decreased ( cow stocked per hectare ( = 0.44). Calf BW at weaning in October increased ( cow BW but was not affected ( = 0.66) by SR. As cow BW increased, calf BW at weaning per 100 kg cow BW decreased ( cow BW but was not affected ( = 0.44) by SR. Neither cow BW nor SR affected ( ≥ 0.53) pregnancy percentage, which averaged 88% over the 4-yr experiment. Calf BW weaned per hectare was not affected ( = 0.75) by cow BW but linearly increased ( cow per hectare SR. Hay feeding days and cost of hay per cow increased ( ≤ 0.05) and kilograms of hay offered per cow tended ( = 0.09) to linearly increase with increasing SR, yet cow BW had no effects ( > 0.22). Although there were no effects ( ≥ 0.38) of cow BW on carrying cost or net returns, increasing SR decreased ( cow and increased net returns by $70/cow and $438/ha for each cow per hectare increase in SR. These data indicate that increasing cow size can increase weaning BW of calves but does not affect total production per hectare or profitability, even though weaning weight efficiency ratios were reduced. Increasing SR reduced cow BW and BCS at weaning and increased feeding of conserved

  9. Low cost high performance uncertainty quantification

    KAUST Repository

    Bekas, C.; Curioni, A.; Fedulova, I.

    2009-01-01

    Uncertainty quantification in risk analysis has become a key application. In this context, computing the diagonal of inverse covariance matrices is of paramount importance. Standard techniques, that employ matrix factorizations, incur a cubic cost

  10. Logistics costs of the enterprise

    Directory of Open Access Journals (Sweden)

    Andrea Rosová

    2007-06-01

    Full Text Available The article describe a problem of specification and systematization of enterprise’s logistics costs. With in a growing division of labour, also logistics costs increase their part in enterprises total costs.Almost all decisions about products and production in general, influence logistics processes even logistics costs and performances.In present is not clear enough, which of the cost-particles are relevant fot logistics costs, because some of logistics cost-particles accounts within overhead are charged together with costs of other sorts.Substantive step in the process of the monitoring and evidence of logistics costs is definition of this, that costs of enterprise´s processes will be inclusive in logistics costs and determining points of contact with the others departments (acquisition, production, sale etc.. After the specification of meditation processes, there is a need to choose applicable parameters for the expression of logistics performances. Besides logistics costs is needed to know logistics performances equivalent herewith at a cost of, therefore from the control side have for enterprise bigger value indices expressive correlation costs and performances(e.g. share of logistics unit costs performance.At the proposal and evidence of logistics costs and performances is needed consistently entertain an individual conditions of enterprise. Because the area of processes included strongly affects the size of account logistics costs and its share part in total costs of enterprise. Logistics costs are flow line between economy and logistics of the enterprise.

  11. Cost and performance optimization of natural draft dry cooling towers using genetic algorithm. Paper no. IGEC-1-002

    International Nuclear Information System (INIS)

    Shokuhmand, H.; Ghaempanah, B.

    2005-01-01

    In this paper the cost - performance optimization of natural draft dry cooling towers with specific kind of heat exchangers, known as Forgo T60 has been investigated. These cooling towers are used in combined and steam cycle power plants. The optimization has been done using genetic algorithm. The objective function has two parts, which are minimizing the cost and maximizing the performance. In the first part the geometrical and operating parameters are defined and for the next part the performance of the designed tower for different ambient temperatures during a year is calculated considering the characteristic curve of the turbine. The applied genetic algorithm has been tuned up using the data of some working power cycles. The results show it is possible to find an optimum for all design parameters; however it is very dependent on how exact the cost analysis is. (author)

  12. Estimating the cost of saving electricity through U.S. utility customer-funded energy efficiency programs

    International Nuclear Information System (INIS)

    Hoffman, Ian M.; Goldman, Charles A.; Rybka, Gregory; Leventis, Greg; Schwartz, Lisa; Sanstad, Alan H.; Schiller, Steven

    2017-01-01

    The program administrator and total cost of saved energy allow comparison of the cost of efficiency across utilities, states, and program types, and can identify potential performance improvements. Comparing program administrator cost with the total cost of saved energy can indicate the degree to which programs leverage investment by participants. Based on reported total costs and savings information for U.S. utility efficiency programs from 2009 to 2013, we estimate the savings-weighted average total cost of saved electricity across 20 states at $0.046 per kilowatt-hour (kW h), comparing favorably with energy supply costs and retail rates. Programs targeted on the residential market averaged $0.030 per kW h compared to $0.053 per kW h for non-residential programs. Lighting programs, with an average total cost of $0.018 per kW h, drove lower savings costs in the residential market. We provide estimates for the most common program types and find that program administrators and participants on average are splitting the costs of efficiency in half. More consistent, standardized and complete reporting on efficiency programs is needed. Differing definitions and quantification of costs, savings and savings lifetimes pose challenges for comparing program results. Reducing these uncertainties could increase confidence in efficiency as a resource among planners and policymakers. - Highlights: • The cost of saved energy allows comparisons among energy resource investments. • Findings from the most expansive collection yet of total energy efficiency program costs. • The weighted average total cost of saved electricity was $0.046 for 20 states in 2009–2013. • Averages in the residential and non-residential sectors were $0.030 and $0.053 per kW h, respectively. • Results strongly indicate need for more consistent, reliable and complete reporting on efficiency programs.

  13. Seismic reliability assessment of RC structures including soil–structure interaction using wavelet weighted least squares support vector machine

    International Nuclear Information System (INIS)

    Khatibinia, Mohsen; Javad Fadaee, Mohammad; Salajegheh, Javad; Salajegheh, Eysa

    2013-01-01

    An efficient metamodeling framework in conjunction with the Monte-Carlo Simulation (MCS) is introduced to reduce the computational cost in seismic reliability assessment of existing RC structures. In order to achieve this purpose, the metamodel is designed by combining weighted least squares support vector machine (WLS-SVM) and a wavelet kernel function, called wavelet weighted least squares support vector machine (WWLS-SVM). In this study, the seismic reliability assessment of existing RC structures with consideration of soil–structure interaction (SSI) effects is investigated in accordance with Performance-Based Design (PBD). This study aims to incorporate the acceptable performance levels of PBD into reliability theory for comparing the obtained annual probability of non-performance with the target values for each performance level. The MCS method as the most reliable method is utilized to estimate the annual probability of failure associated with a given performance level in this study. In WWLS-SVM-based MCS, the structural seismic responses are accurately predicted by WWLS-SVM for reducing the computational cost. To show the efficiency and robustness of the proposed metamodel, two RC structures are studied. Numerical results demonstrate the efficiency and computational advantages of the proposed metamodel for the seismic reliability assessment of structures. Furthermore, the consideration of the SSI effects in the seismic reliability assessment of existing RC structures is compared to the fixed base model. It shows which SSI has the significant influence on the seismic reliability assessment of structures.

  14. Does Successful Weight Loss in an Internet-Based Worksite Weight Loss Program Improve Employee Presenteeism and Absenteeism?

    Science.gov (United States)

    Harden, Samantha M.; You, Wen; Almeida, Fabio A.; Hill, Jennie L.; Linnan, Laura A.; Allen, Kacie C.; Estabrooks, Paul A.

    2017-01-01

    Certain risk factors associated with overweight and obesity may lead to reduced productivity in the workforce (i.e., increased absenteeism and presenteeism). Participants in a large, Internet-based worksite weight loss intervention, who were present at follow-up (N = 1,030), completed a self-reported productivity measure (World Health Organization’s Health and Work Performance Questionnaire) at baseline and postintervention. Twenty-two percent of the participants lost a clinically meaningful amount of weight (≥5% weight loss). There were no statistically significant (p absenteeism or for absolute or relative presenteeism. Within a modestly successful Internet-based, worksite weight loss intervention, weight loss did not improve self-reported absenteeism or presenteeism. Further studies are needed to explore the sensitivity of the World Health Organization’s Health and Work Performance Questionnaire and the long-term effects of weight loss on productivity. PMID:25842385

  15. Randomised controlled trial and economic analysis of an internet-based weight management programme: POWeR+ (Positive Online Weight Reduction).

    Science.gov (United States)

    Little, Paul; Stuart, Beth; Hobbs, Fd Richard; Kelly, Jo; Smith, Emily R; Bradbury, Katherine J; Hughes, Stephanie; Smith, Peter Wf; Moore, Michael V; Lean, Mike Ej; Margetts, Barrie M; Byrne, Christopher D; Griffin, Simon; Davoudianfar, Mina; Hooper, Julie; Yao, Guiqing; Zhu, Shihua; Raftery, James; Yardley, Lucy

    2017-01-01

    Behavioural counselling with intensive follow-up for obesity is effective, but in resource-constrained primary care settings briefer approaches are needed. To estimate the clinical effectiveness and cost-effectiveness of an internet-based behavioural intervention with regular face-to-face or remote support in primary care, compared with brief advice. Individually randomised three-arm parallel trial with health economic evaluation and nested qualitative interviews. Primary care general practices in the UK. Patients with a body mass index of ≥ 30 kg/m 2 (or ≥ 28 kg/m 2 with risk factors) identified from general practice records, recruited by postal invitation. Positive Online Weight Reduction (POWeR+) is a 24-session, web-based weight management intervention completed over 6 months. Following online registration, the website randomly allocated participants using computer-generated random numbers to (1) the control intervention ( n  = 279), which had previously been demonstrated to be clinically effective (brief web-based information that minimised pressure to cut down foods, instead encouraging swaps to healthier choices and increasing fruit and vegetables, plus 6-monthly nurse weighing); (2) POWeR+F ( n  = 269), POWeR+ supplemented by face-to-face nurse support (up to seven contacts); or (3) POWeR+R ( n  = 270), POWeR+ supplemented by remote nurse support (up to five e-mails or brief telephone calls). The primary outcome was a modelled estimate of average weight reduction over 12 months, assessed blind to group where possible, using multiple imputation for missing data. The secondary outcome was the number of participants maintaining a 5% weight reduction at 12 months. A total of 818 eligible individuals were randomised using computer-generated random numbers. Weight change, averaged over 12 months, was documented in 666 out of 818 participants (81%; control, n  = 227; POWeR+F, n  = 221; POWeR+R, n  = 218). The control group

  16. Supply disruption cost for power network planning

    International Nuclear Information System (INIS)

    Kjoelle, G.H.

    1992-09-01

    A description is given of the method of approach to calculate the total annual socio-economic cost of power supply disruption and non-supplied energy, included the utilities' cost for planning. The total socio-economic supply disruption cost is the sum of the customers' disruption cost and the utilities' cost for failure and disruption. The mean weighted disruption cost for Norway for one hour disruption is NOK 19 per kWh. The customers' annual disruption cost is calculated with basis in the specific disruption cost referred to heavy load (January) and dimensioning maximum loads. The loads are reduced by factors taking into account the time variations of the failure frequency, duration, the loads and the disruption cost. 6 refs

  17. Growth Performance of Pekin Ducks Fed with Golden Snail and Fresh Banana Peelings

    Directory of Open Access Journals (Sweden)

    Ulep, LJL.

    1995-01-01

    Full Text Available The growth performance and economics of feeding confined Pekin ducks with three different levels of golden snail fresh meat and banana peelings in equal percentage for replacing 50 %, 70 % or 90 % of the commercial feed of the diet was studied. Body weight gains and feed consumption of ducks, cost of feed and profit above feed and stock cost different significantly among treatments. Feed conversion varied during the first month of feeding but became comparable after the second month. Ducks fed the diet with 45 % banana peel and 45 % golden snail meat gave the best performance, were the most economical and yielded the highest profit. Snail meat and banana peeling utilization as replacement to commercial diet for ducks is advantageaous in terms of growth performance and cost benefit.

  18. Control of body weight by eating behavior in children

    Directory of Open Access Journals (Sweden)

    Modjtaba eZandian

    2015-10-01

    Full Text Available Diet, exercise, and pharmacological interventions have limited effects in counteracting the worldwide increase in pediatric body weight. Moreover, the promise that individualized drug design will work to induce weight loss appears to be exaggerated. We suggest that the reason for this limited success is that the cause of obesity has been misunderstood. Body weight is mainly under external control; our brain permits us to eat under most circumstances, and unless the financial or physical cost of food is high, eating and body weight increase by default. When energy-rich, inexpensive foods are continually available, people need external support to maintain a healthy body weight. Weight loss can thereby be achieved by continuous feedback on how much and how fast to eat on a computer screen.

  19. The relationship between health risks and health and productivity costs among employees at Pepsi Bottling Group.

    Science.gov (United States)

    Henke, Rachel M; Carls, Ginger S; Short, Meghan E; Pei, Xiaofei; Wang, Shaohung; Moley, Susan; Sullivan, Mark; Goetzel, Ron Z

    2010-05-01

    To evaluate relationships between modifiable health risks and costs and measure potential cost savings from risk reduction programs. Health risk information from active Pepsi Bottling Group employees who completed health risk assessments between 2004 and 2006 (N = 11,217) were linked to medical care, workers' compensation, and short-term disability cost data. Ten health risks were examined. Multivariate analyses were performed to estimate costs associated with having high risk, holding demographics, and other risks constant. Potential savings from risk reduction were estimated. High risk for weight, blood pressure, glucose, and cholesterol had the greatest impact on total costs. A one-percentage point annual reduction in the health risks assessed would yield annual per capita savings of $83.02 to $103.39. Targeted programs that address modifiable health risks are expected to produce substantial cost reductions in multiple benefit categories.

  20. Life cycle cost-based risk model for energy performance contracting retrofits

    Science.gov (United States)

    Berghorn, George H.

    Buildings account for 41% of the primary energy consumption in the United States, nearly half of which is accounted for by commercial buildings. Among the greatest energy users are those in the municipalities, universities, schools, and hospitals (MUSH) market. Correctional facilities are in the upper half of all commercial building types for energy intensity. Public agencies have experienced reduced capital budgets to fund retrofits; this has led to the increased use of energy performance contracts (EPC), which are implemented by energy services companies (ESCOs). These companies guarantee a minimum amount of energy savings resulting from the retrofit activities, which in essence transfers performance risk from the owner to the contractor. Building retrofits in the MUSH market, especially correctional facilities, are well-suited to EPC, yet despite this potential and their high energy intensities, efficiency improvements lag behind that of other public building types. Complexities in project execution, lack of support for data requests and sub-metering, and conflicting project objectives have been cited as reasons for this lag effect. As a result, project-level risks must be understood in order to support wider adoption of retrofits in the public market, in particular the correctional facility sub-market. The goal of this research is to understand risks related to the execution of energy efficiency retrofits delivered via EPC in the MUSH market. To achieve this goal, in-depth analysis and improved understanding was sought with regard to ESCO risks that are unique to EPC in this market. The proposed work contributes to this understanding by developing a life cycle cost-based risk model to improve project decision making with regard to risk control and reduction. The specific objectives of the research are: (1) to perform an exploratory analysis of the EPC retrofit process and identify key areas of performance risk requiring in-depth analysis; (2) to construct a

  1. A cost-controlling treatment strategy of adding liraglutide to insulin in type 2 diabetes.

    Science.gov (United States)

    de Wit, H M; Vervoort, G M M; de Galan, B E; Tack, C J

    2017-09-01

    Addition of the GLP-1 receptor agonist liraglutide to insulin can reverse insulin-associated weight gain, improve HbA1c and decrease the need for insulin, but is expensive. From a cost perspective, such treatment should be discontinued when it is clear that treatment targets will not be achieved. Our aim was to find the best cost-controlling treatment strategy: the shortest possible trial period needed to discriminate successfully treated patients from those failing to achieve predefined targets of treatment success. We used data from the 'Effect of Liraglutide on insulin-associated wEight GAiN in patients with Type 2 diabetes' (ELEGANT) trial, comparing additional liraglutide (n = 47) and standard insulin therapy (n = 24) during 26 weeks, to calculate the costs associated with different trial periods. Treatment success after 26 weeks was defined by having achieved ≥ 2 of the following: ≥ 4% weight loss, HbA1c ≤ 53 mmol/mol (7%), and/or discontinuation of insulin. The additional direct costs of adding liraglutide for 26 weeks were € 699 per patient, or € 137 per 1 kg weight loss, compared with standard therapy. The best cost-controlling treatment strategy (identifying 21 of 23 responders, treating four non-responders) was to continue treatment in patients showing ≥ 3% weight loss or ≥ 60% decrease in insulin dose at 8 weeks, with a total cost of € 246 for this t rial period, saving € 453 in case of early discontinuation. An 8-week trial period of adding liraglutide to insulin in patients with insulin-associated weight gain is an effective cost-controlling treatment strategy if the liraglutide is discontinued in patients not showing an early response regarding weight loss or insulin reduction.

  2. An Analysis of the Cost and Performance of Photovoltaic Systems as a Function of Module Area

    Energy Technology Data Exchange (ETDEWEB)

    Horowitz, Kelsey A.W. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Fu, Ran [National Renewable Energy Lab. (NREL), Golden, CO (United States); Silverman, Tim [National Renewable Energy Lab. (NREL), Golden, CO (United States); Woodhouse, Mike [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sun, Xingshu [Purdue Univ., West Lafayette, IN (United States); Alam, Mohammed A. [Purdue Univ., West Lafayette, IN (United States)

    2017-04-07

    We investigate the potential effects of module area on the cost and performance of photovoltaic systems. Applying a bottom-up methodology, we analyzed the costs associated with mc-Si and thin-film modules and systems as a function of module area. We calculate a potential for savings of up to $0.04/W, $0.10/W, and $0.13/W in module manufacturing costs for mc-Si, CdTe, and CIGS respectively, with large area modules. We also find that an additional $0.05/W savings in balance-of-systems costs may be achieved. However, these savings are dependent on the ability to maintain efficiency and manufacturing yield as area scales. Lifetime energy yield must also be maintained to realize reductions in the levelized cost of energy. We explore the possible effects of module size on efficiency and energy production, and find that more research is required to understand these issues for each technology. Sensitivity of the $/W cost savings to module efficiency and manufacturing yield is presented. We also discuss non-cost barriers to adoption of large area modules.

  3. Common weights under dea control

    International Nuclear Information System (INIS)

    Agrell, P.J.; Bogetoft, P.; Fristrup, P.

    2003-01-01

    DEA relies so far on endogenous local or exogenous general weights, limited to available information. We offer endogenous general prices based on a reformulation of DEA. The potential application could be to precipitate collective bargaining on cost efficiency. The models are exemplified with data from the Danish district heating plants, where the open evaluation of multiple non-priced outputs is relevant (au)

  4. A Decidable Recursive Logic for Weighted Transition Systems

    DEFF Research Database (Denmark)

    Xue, Bingtian; Larsen, Kim Guldstrand; Mardare, Radu Iulian

    2014-01-01

    In this paper we develop and study the Recursive Weighted Logic (RWL), a multi-modal logic that expresses qualitative and quantitative properties of labelled weighted transition systems (LWSs). LWSs are transition systems labelled with actions and real-valued quantities representing the costs of ...... extends previous results that we have demonstrated for a similar but much more restrictive logic that can only use one variable for each type of resource to encode logical properties....

  5. Performance Evaluation and Community Application of Low-Cost Sensors for Ozone and Nitrogen Dioxide

    Science.gov (United States)

    This study reports on the performance of electrochemical-based low-cost sensors and their use in a community application. CairClip sensors were collocated with federal reference and equivalent methods and operated in a network of sites by citizen scientists (community members) in...

  6. Adding evidence-based behavioral weight loss strategies to a statewide wellness campaign: a randomized clinical trial.

    Science.gov (United States)

    Leahey, Tricia M; Thomas, Graham; Fava, Joseph L; Subak, Leslee L; Schembri, Michael; Krupel, Katie; Kumar, Rajiv; Weinberg, Brad; Wing, Rena R

    2014-07-01

    We determined the efficacy and cost-effectiveness of adding an evidence-based Internet behavioral weight loss intervention alone or combined with optional group sessions to ShapeUp Rhode Island 2011 (SURI), a 3-month statewide wellness campaign. We randomized participants (n = 230; body mass index = 34.3 ±6.8 kg/m(2); 84% female) to the standard SURI program (S) or to 1 of 2 enhanced programs: SURI plus Internet behavioral program (SI) or SI plus optional group sessions (SIG). The primary outcome was weight loss at the end of the 3-month program. Weight losses differed among all 3 conditions (S: 1.1% ±0.9%; SI: 4.2% ±0.6%; SIG: 6.1% ±0.6%; Ps ≤ .04). Both SI and SIG increased the percentage of individuals who achieved a 5% weight loss (SI: 42%; SIG: 54%; S: 7%; Ps < .001). Cost per kilogram of weight loss was similar for S ($39) and SI ($35); both were lower than SIG ($114). Although weight losses were greatest at the end of SURI with optional group sessions, the addition of an Internet behavioral program was the most cost-effective method to enhance weight losses.

  7. Targeting the underlying causes of undernutrition. Cost-effectiveness of a multifactorial personalized intervention in community-dwelling older adults: A randomized controlled trial.

    Science.gov (United States)

    van der Pols-Vijlbrief, Rachel; Wijnhoven, Hanneke A H; Bosmans, Judith E; Twisk, Jos W R; Visser, Marjolein

    2017-12-01

    Undernutrition in old age is associated with increased morbidity, mortality and health care costs. Treatment by caloric supplementation results in weight gain, but compliance is poor in the long run. Few studies targeted underlying causes of undernutrition in community-dwelling older adults. This study aimed to evaluate the cost-effectiveness of a multifactorial personalized intervention focused on eliminating or managing the underlying causes of undernutrition to prevent and reduce undernutrition in comparison with usual care. A randomized controlled trial was performed among 155 community-dwelling older adults receiving home care with or at risk of undernutrition. The intervention included a personalized action plan and 6 months support. The control group received usual care. Body weight, and secondary outcomes were measured in both groups at baseline and 6 months follow-up. Multiple imputation, linear regression and generalized estimating equation analyses were used to analyze intervention effects. In the cost-effectiveness analyses regression models were bootstrapped to estimate statistical uncertainty. This intervention showed no statistically significant effects on body weight, mid-upper arm circumference, grip strength, gait speed and 12-Item Short-Form Health Survey physical component scale as compared to usual care, but there was an effect on the 12-Item Short-Form Health Survey mental component scale (0-100) (β = 8.940, p=0.001). Borderline significant intervention effects were found for both objective and subjective physical function measures, Short Physical Performance Battery (0-12) (β = 0.56, p=0.08) and ADL-Barthel score (0-20) (β = 0.69, p=0.09). Societal costs in the intervention group were statistically non-significantly lower than in the control group (mean difference -274; 95% CI -1111; 782). Cost-effectiveness acceptability curves showed that the probability of cost-effectiveness was 0.72 at a willingness-to-pay of 1000

  8. Partitioning the Metabolic Cost of Human Running: A Task-by-Task Approach

    Science.gov (United States)

    Arellano, Christopher J.; Kram, Rodger

    2014-01-01

    Compared with other species, humans can be very tractable and thus an ideal “model system” for investigating the metabolic cost of locomotion. Here, we review the biomechanical basis for the metabolic cost of running. Running has been historically modeled as a simple spring-mass system whereby the leg acts as a linear spring, storing, and returning elastic potential energy during stance. However, if running can be modeled as a simple spring-mass system with the underlying assumption of perfect elastic energy storage and return, why does running incur a metabolic cost at all? In 1980, Taylor et al. proposed the “cost of generating force” hypothesis, which was based on the idea that elastic structures allow the muscles to transform metabolic energy into force, and not necessarily mechanical work. In 1990, Kram and Taylor then provided a more explicit and quantitative explanation by demonstrating that the rate of metabolic energy consumption is proportional to body weight and inversely proportional to the time of foot-ground contact for a variety of animals ranging in size and running speed. With a focus on humans, Kram and his colleagues then adopted a task-by-task approach and initially found that the metabolic cost of running could be “individually” partitioned into body weight support (74%), propulsion (37%), and leg-swing (20%). Summing all these biomechanical tasks leads to a paradoxical overestimation of 131%. To further elucidate the possible interactions between these tasks, later studies quantified the reductions in metabolic cost in response to synergistic combinations of body weight support, aiding horizontal forces, and leg-swing-assist forces. This synergistic approach revealed that the interactive nature of body weight support and forward propulsion comprises ∼80% of the net metabolic cost of running. The task of leg-swing at most comprises ∼7% of the net metabolic cost of running and is independent of body weight support and forward

  9. Reducing BWR O and M costs through on-line performance monitoring

    International Nuclear Information System (INIS)

    Jonas, T.; Gross, R.; Logback, F.; Josyula, R.

    1995-01-01

    Competition in the electric power industry has placed significant emphasis on reducing operating and maintenance (O and M) costs at nuclear facilities. Therefore, on-line performance monitoring to locate power losses for boiling water reactor (BWR) plants is creating tremendous interest. In addition, the ability to automate activities such as data collection, analysis, and reporting increases the efficiency of plant engineers and gives them more time to concentrate on solving plant efficiency problems. This capability is now available with a unique software product called GEBOPS. GE Nuclear Energy, in conjunction with Joint Venture partner Black and Veatch, has undertaken development of the General Electric/Black and Veatch On-line Performance System (GEBOPS), an on-line performance monitoring system for BWR plants. The experience and expertise of GE Nuclear Energy with BWR plants, coupled with the proven on-line monitoring software development experience and capability of Black and Veatch, provide the foundation for a unique product which addresses the needs of today's BWR plants

  10. Influences of the Capital Structure and the Cost of Capital on Financial Performance. Case Study on ENGIE Group

    OpenAIRE

    Elena Valentina IVASCU; Nicoleta BARBUTA-MISU

    2017-01-01

    The main objectives of the company's financial management are to ensure financial performances and to choose the capital structure that corresponds to the lowest total cost of capital. The purpose of this paper is to analyse the relationship between the capital structure and cost, and the financial performance of Engie Transnational Group, one of the most important global electricity producers. The data used were extracted from the Amadeus and Bloomberg databases for the period 2010-2015. Fin...

  11. Predicting Production Costs for Advanced Aerospace Vehicles

    Science.gov (United States)

    Bao, Han P.; Samareh, J. A.; Weston, R. P.

    2002-01-01

    For early design concepts, the conventional approach to cost is normally some kind of parametric weight-based cost model. There is now ample evidence that this approach can be misleading and inaccurate. By the nature of its development, a parametric cost model requires historical data and is valid only if the new design is analogous to those for which the model was derived. Advanced aerospace vehicles have no historical production data and are nowhere near the vehicles of the past. Using an existing weight-based cost model would only lead to errors and distortions of the true production cost. This paper outlines the development of a process-based cost model in which the physical elements of the vehicle are soared according to a first-order dynamics model. This theoretical cost model, first advocated by early work at MIT, has been expanded to cover the basic structures of an advanced aerospace vehicle. Elemental costs based on the geometry of the design can be summed up to provide an overall estimation of the total production cost for a design configuration. This capability to directly link any design configuration to realistic cost estimation is a key requirement for high payoff MDO problems. Another important consideration in this paper is the handling of part or product complexity. Here the concept of cost modulus is introduced to take into account variability due to different materials, sizes, shapes, precision of fabrication, and equipment requirements. The most important implication of the development of the proposed process-based cost model is that different design configurations can now be quickly related to their cost estimates in a seamless calculation process easily implemented on any spreadsheet tool.

  12. Trouble Sleeping Associated with Lower Work Performance and Greater Healthcare Costs: Longitudinal Data from Kansas State Employee Wellness Program

    Science.gov (United States)

    Hui, Siu-kuen Azor; Grandner, Michael A.

    2015-01-01

    Objective To examine the relationships between employees’ trouble sleeping and absenteeism, work performance, and healthcare expenditures over a two year period. Methods Utilizing the Kansas State employee wellness program (EWP) dataset from 2008–2009, multinomial logistic regression analyses were conducted with trouble sleeping as the predictor and absenteeism, work performance, and healthcare costs as the outcomes. Results EWP participants (N=11,698 in 2008; 5,636 followed up in 2009) who had higher levels of sleep disturbance were more likely to be absent from work (all p performance ratings (all p performance, and healthcare costs. PMID:26461857

  13. Does Successful Weight Loss in an Internet-Based Worksite Weight Loss Program Improve Employee Presenteeism and Absenteeism?

    Science.gov (United States)

    Harden, Samantha M; You, Wen; Almeida, Fabio A; Hill, Jennie L; Linnan, Laura A; Allen, Kacie C; Estabrooks, Paul A

    2015-12-01

    Certain risk factors associated with overweight and obesity may lead to reduced productivity in the workforce (i.e., increased absenteeism and presenteeism). Participants in a large, Internet-based worksite weight loss intervention, who were present at follow-up (N = 1,030), completed a self-reported productivity measure (World Health Organization's Health and Work Performance Questionnaire) at baseline and postintervention. Twenty-two percent of the participants lost a clinically meaningful amount of weight (≥5% weight loss). There were no statistically significant (p absenteeism or for absolute or relative presenteeism. Within a modestly successful Internet-based, worksite weight loss intervention, weight loss did not improve self-reported absenteeism or presenteeism. Further studies are needed to explore the sensitivity of the World Health Organization's Health and Work Performance Questionnaire and the long-term effects of weight loss on productivity. © 2015 Society for Public Health Education.

  14. EFFECT OF AGE AND BODY WEIGHT AT MOLTING ON THE PERFORMANCE OF BROILER BREEDER HENS UNDER ENVIRONMENTAL CONTROL HOUSES IN PAKISTAN

    Directory of Open Access Journals (Sweden)

    HASSAN M. MALIK, EHSAN-UL-HAQ AND F. AHMAD

    2008-12-01

    Full Text Available In the present study, 2700 broiler breeder hens of Arbor Acre strain were divided into 27 experimental units (100 each and allotted to nine treatments randomly having three replications each. The birds were kept under uniform managemental conditions throughout the experimental period of 32 weeks post molt period. The birds were molted under conventional method at 50, 55 and 60 weeks of age having three different body weights i.e. 3000, 3500 and 4000 ± 50g under 3x3 factorial design. At the time of 5% production, data on production performance (weekly eggs/hen, hen day production, body weight and feed consumption were recorded. Data collected was analyzed by analysis of variance technique under 3x3 factorial arrangement of treatment and the differences among the treatment means were analyzed by Duncan’s Multiple Range test. Significant (P<0.05 differences due to body weight and age were noted for feed consumption, weekly eggs per hen, hen day production and hen house production. Broiler breeders having low age group (50 weeks and medium body weight (3500g resulted in maximum production performance/net profit.

  15. The Role of Dairy in Effectiveness and Cost of Treatment of Children With Moderate Acute Malnutrition: A Narrative Review.

    Science.gov (United States)

    Suri, Devika J; Moorthy, Denish; Rosenberg, Irwin H

    2016-06-01

    Dairy is recommended in specially formulated supplementary foods to treat children with moderate acute malnutrition (MAM) but with limited evidence and added cost. Review studies of ready-to-use foods (RUFs) versus fortified blended foods (FBFs) to determine whether inclusion of dairy modifies the comparative effectiveness and cost. We reviewed literature comparing FBF and RUF in treatment of MAM among children younger than 5 years in developing countries. Outcomes of recovery from MAM, weight, and length gain were compared among treatment categories: FBF with dairy (FBF+), FBF without dairy (FBF-), RUF with dairy (RUF+), and RUF without dairy (RUF-). Supplement cost was compared per 500 kcal. Eight studies were included. Rations were heterogeneous in energy and type of dairy. Overall, RUF+, RUF-, and FBF+ performed similarly, with higher recovery and weight gain compared with FBF-. RUF+ had higher recovery (in 5 of 6 comparisons), weight gain (4 of 4), and length gain (1 of 4) versus FBF-. The RUF+ had higher recovery (1 of 2) versus FBF+, with no other differences. The RUF- versus FBF+ had no differences (0 of 2). The RUF- had higher recovery (1 of 2), weight gain (2 of 2) versus FBF-. Four studies reported supplement costs, which averaged US$0.15 (FBF-), US$0.18 (FBF+), US$0.18 (RUF-), and US$0.37 (RUF+) per 500 kcal. There is a consistent benefit of FBF that include dairy in treatment of children with MAM. Benefits of dairy in RUF require further investigation. Evidence from rigorous quantitative analysis of existing data, cost-effectiveness, and prospective trials will be essential in determining policy on treatment for children with MAM. © The Author(s) 2016.

  16. Transaction-cost Expenditures and the Relative Performance of Mutual Funds

    OpenAIRE

    John M.R. Chalmers; Roger M. Edelen; Gregory B. Kadlec

    1999-01-01

    We directly estimate annual trading costs for a sample of equity mutual funds and find that these costs are large and exhibit substantial cross sectional variation. Trading costs average 0.78% of fund assets per year and have an inter-quartile range of 0.59%. Trading costs, like expense ratios, are negatively related to fund returns and we find no evidence that on average trading costs are recovered in higher gross fund returns. We find that our direct estimates of trading costs have more exp...

  17. Improving the performance of membrane bioreactors by powdered activated carbon dosing with cost considerations.

    Science.gov (United States)

    Yang, W; Paetkau, M; Cicek, N

    2010-01-01

    Effects of powdered activated carbon (PAC) dosing on the overall performance of membrane bioreactors (MBR) were investigated in two bench-scale submerged MBRs. Positive impacts of PAC dosing on membrane fouling and the removal of 17beta-estradiol (E2) and 17alpha-ethyinylestradiol (EE2) were demonstrated over a six-month stable operational period. PAC dosing in the MBR increased the removal rates of E2 and EE2 by 3.4% and 15.8%, respectively. The average soluble extracellular polymeric substances (EPS) and colloidal total organic carbon (TOC) concentrations in the PAC-MBR sludge was 60.1% and 61.8% lower than the control MBR sludge, respectively. Lower soluble EPS and colloidal TOC concentrations in the PAC-MBR sludge resulted in a slower rate of trans-membrane pressure (TMP) increase during MBRs operation, which could prolong the lifespan of membranes. Cost assessment showed that PAC dosing could reduce the operating cost for membrane cleaning and/or membrane replacement by about 25%. The operating cost for PAC dosing could be offset by the benefit from its reducing the cost for membrane maintenance.

  18. Performance of a neuro-fuzzy model in predicting weight changes of chronic schizophrenic patients exposed to antipsychotics.

    Science.gov (United States)

    Lan, T H; Loh, E W; Wu, M S; Hu, T M; Chou, P; Lan, T Y; Chiu, H-J

    2008-12-01

    Artificial intelligence has become a possible solution to resolve the problem of loss of information when complexity of a disease increases. Obesity phenotypes are observable clinical features of drug-naive schizophrenic patients. In addition, atypical antipsychotic medications may cause these unwanted effects. Here we examined the performance of neuro-fuzzy modeling (NFM) in predicting weight changes in chronic schizophrenic patients exposed to antipsychotics. Two hundred and twenty inpatients meeting DSMIV diagnosis of schizophrenia, treated with antipsychotics, either typical or atypical, for more than 2 years, were recruited. All subjects were assessed in the same study period between mid-November 2003 and mid-April 2004. The baseline and first visit's physical data including weight, height and circumference were used in this study. Clinical information (Clinical Global Impression and Life Style Survey) and genotype data of five single nucleotide polymorphisms were also included as predictors. The subjects were randomly assigned into the first group (105 subjects) and second group (115 subjects), and NFM was performed by using the FuzzyTECH 5.54 software package, with a network-type structure constructed in the rule block. A complete learned model trained from merged data of the first and second groups demonstrates that, at a prediction error of 5, 93% subjects with weight gain were identified. Our study suggests that NFM is a feasible prediction tool for obesity in schizophrenic patients exposed to antipsychotics, with further improvements required.

  19. Integrated model of assisted parking system and performance evaluation with entropy weight extended analytic hierarchy process and two-tuple linguistic information

    Directory of Open Access Journals (Sweden)

    Yiding Hua

    2016-06-01

    Full Text Available Evaluating comprehensive performance of assisted parking system has been a very important issue for car companies for years, because the overall performance of assisted parking system directly influences car intellectualization and customers’ degree of satisfaction. Therefore, this article proposes two-tuple linguistic analytic hierarchy process to evaluate assisted parking system so as to avoid information loss during the processes of evaluation integration. The performance evaluation attributes for assisted parking system are established initially. Subsequently, the information entropy theory is proposed to improve the evaluation attribute weight determined by analytic hierarchy process for the influencing factors of the randomness in parking test process. Furthermore, the evaluation attribute measure values of comprehensive performance are calculated and the assisted parking system evaluation results are obtained with ordered weighted averaging operator. Finally, numerical examples of vehicle types equipped with eight different assisted parking systems and computational results are presented.

  20. Academy of Nutrition and Dietetics: standards of practice and standards of professional performance for registered dietitian nutritionists (competent, proficient, and expert) in adult weight management.

    Science.gov (United States)

    Jortberg, Bonnie; Myers, Eileen; Gigliotti, Linda; Ivens, Barbara J; Lebre, Monica; Burke March, Susan; Nogueira, Isadora; Nwankwo, Robin; Parkinson, Meredith R; Paulsen, Barbara; Turner, Tonya

    2015-04-01

    Weight management encompasses the inter-relationship of nutrition, physical activity, and health behavior change. Nutrition is key for the prevention and treatment of obesity and chronic disease and maintenance of overall health. Thus, the Weight Management Dietetic Practice Group, with guidance from the Academy of Nutrition and Dietetics Quality Management Committee, has developed Standards of Practice and Standards of Professional Performance for Registered Dietitian Nutritionists (RDNs) in Adult Weight Management as a resource for RDNs working in weight management. This document allows RDNs to assess their current skill levels and to identify areas for further professional development in this expanding practice area. This document describes the current standards for weight management practice for RDNs. The Standards of Practice represent the four steps in the Nutrition Care Process as applied to the care of patients/clients. The Standards of Professional Performance consist of six domains of professionalism: Quality in Practice, Competence and Accountability, Provision of Services, Application of Research, Communication and Application of Knowledge, and Utilization and Management of Resources. Within each standard, specific indicators provide measurable action statements that illustrate how the standard can be applied to practice. The indicators describe three skill levels (competent, proficient, and expert) for RDNs working in weight management. The Standards of Practice and Standards of Professional Performance are complementary resources for the Registered Dietitian Nutritionist in weight management. Copyright © 2015 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

  1. Designers' unified cost model

    Science.gov (United States)

    Freeman, W.; Ilcewicz, L.; Swanson, G.; Gutowski, T.

    1992-01-01

    The Structures Technology Program Office (STPO) at NASA LaRC has initiated development of a conceptual and preliminary designers' cost prediction model. The model will provide a technically sound method for evaluating the relative cost of different composite structural designs, fabrication processes, and assembly methods that can be compared to equivalent metallic parts or assemblies. The feasibility of developing cost prediction software in a modular form for interfacing with state-of-the-art preliminary design tools and computer aided design programs is being evaluated. The goal of this task is to establish theoretical cost functions that relate geometric design features to summed material cost and labor content in terms of process mechanics and physics. The output of the designers' present analytical tools will be input for the designers' cost prediction model to provide the designer with a database and deterministic cost methodology that allows one to trade and synthesize designs with both cost and weight as objective functions for optimization. This paper presents the team members, approach, goals, plans, and progress to date for development of COSTADE (Cost Optimization Software for Transport Aircraft Design Evaluation).

  2. Investigating satiety for healthy weight : Appetite control

    NARCIS (Netherlands)

    Burgering, M.J.M.

    2013-01-01

    Modulating feelings of hunger and satiety could be a promising approach in weight management. TNO Food & Nutrition offers advanced assessment tools to support the development of food products that help address issues of overweight and underweight. This can reduce time, cost, and time-to-market.

  3. Selection for body weight in dairy cattle

    NARCIS (Netherlands)

    Koenen, E.P.C.

    2001-01-01

    This thesis deals with selection for body weight (BW) in dairy cattle. The economic efficiency of present breeding schemes might increase further when selection decisions also consider information on BW as BW relates to feed costs and revenues from beef production. However, the practical

  4. Assessing the Performance of a Network of Low Cost Particulate Matter Sensors Deployed in Sacramento, California

    Science.gov (United States)

    Mukherjee, A. D.; Brown, S. G.; McCarthy, M. C.

    2017-12-01

    A new generation of low cost air quality sensors have the potential to provide valuable information on the spatial-temporal variability of air pollution - if the measurements have sufficient quality. This study examined the performance of a particulate matter sensor model, the AirBeam (HabitatMap Inc., Brooklyn, NY), over a three month period in the urban environment of Sacramento, California. Nineteen AirBeam sensors were deployed at a regulatory air monitoring site collocated with meteorology measurements and as a local network over an 80 km2 domain in Sacramento, CA. This study presents the methodology to evaluate the precision, accuracy, and reliability of the sensors over a range of meteorological and aerosol conditions. The sensors demonstrated a robust degree of precision during collocated measurement periods (R2 = 0.98 - 0.99) and a moderate degree of correlation against a Beta Attenuation Monitor PM2.5 monitor (R2 0.6). A normalization correction is applied during the study period so that each AirBeam sensor in the network reports a comparable value. The role of the meteorological environment on the accuracy of the sensor measurements is investigated, along with the possibility of improving the measurements through a meteorology weighted correction. The data quality of the network of sensors is examined, and the spatial variability of particulate matter through the study domain derived from the sensor network is presented.

  5. Reducing weight precision of convolutional neural networks towards large-scale on-chip image recognition

    Science.gov (United States)

    Ji, Zhengping; Ovsiannikov, Ilia; Wang, Yibing; Shi, Lilong; Zhang, Qiang

    2015-05-01

    In this paper, we develop a server-client quantization scheme to reduce bit resolution of deep learning architecture, i.e., Convolutional Neural Networks, for image recognition tasks. Low bit resolution is an important factor in bringing the deep learning neural network into hardware implementation, which directly determines the cost and power consumption. We aim to reduce the bit resolution of the network without sacrificing its performance. To this end, we design a new quantization algorithm called supervised iterative quantization to reduce the bit resolution of learned network weights. In the training stage, the supervised iterative quantization is conducted via two steps on server - apply k-means based adaptive quantization on learned network weights and retrain the network based on quantized weights. These two steps are alternated until the convergence criterion is met. In this testing stage, the network configuration and low-bit weights are loaded to the client hardware device to recognize coming input in real time, where optimized but expensive quantization becomes infeasible. Considering this, we adopt a uniform quantization for the inputs and internal network responses (called feature maps) to maintain low on-chip expenses. The Convolutional Neural Network with reduced weight and input/response precision is demonstrated in recognizing two types of images: one is hand-written digit images and the other is real-life images in office scenarios. Both results show that the new network is able to achieve the performance of the neural network with full bit resolution, even though in the new network the bit resolution of both weight and input are significantly reduced, e.g., from 64 bits to 4-5 bits.

  6. Using Incomplete Information for Complete Weight Annotation of Road Networks

    DEFF Research Database (Denmark)

    Yang, Bin; Kaul, Manohar; Jensen, Christian S.

    2014-01-01

    ground-truth travel cost. A general framework is proposed to solve the problem. Specifically, the problem is modeled as a regression problem and solved by minimizing a judiciously designed objective function that takes into account the topology of the road network. In particular, the use of weighted Page......Rank values of edges is explored for assigning appropriate weights to all edges, and the property of directional adjacency of edges is also taken into account to assign weights. Empirical studies with weights capturing travel time and GHG emissions on two road networks offer insight into the design properties...

  7. Weight Loss Nutritional Supplements

    Science.gov (United States)

    Eckerson, Joan M.

    Obesity has reached what may be considered epidemic proportions in the United States, not only for adults but for children. Because of the medical implications and health care costs associated with obesity, as well as the negative social and psychological impacts, many individuals turn to nonprescription nutritional weight loss supplements hoping for a quick fix, and the weight loss industry has responded by offering a variety of products that generates billions of dollars each year in sales. Most nutritional weight loss supplements are purported to work by increasing energy expenditure, modulating carbohydrate or fat metabolism, increasing satiety, inducing diuresis, or blocking fat absorption. To review the literally hundreds of nutritional weight loss supplements available on the market today is well beyond the scope of this chapter. Therefore, several of the most commonly used supplements were selected for critical review, and practical recommendations are provided based on the findings of well controlled, randomized clinical trials that examined their efficacy. In most cases, the nutritional supplements reviewed either elicited no meaningful effect or resulted in changes in body weight and composition that are similar to what occurs through a restricted diet and exercise program. Although there is some evidence to suggest that herbal forms of ephedrine, such as ma huang, combined with caffeine or caffeine and aspirin (i.e., ECA stack) is effective for inducing moderate weight loss in overweight adults, because of the recent ban on ephedra manufacturers must now use ephedra-free ingredients, such as bitter orange, which do not appear to be as effective. The dietary fiber, glucomannan, also appears to hold some promise as a possible treatment for weight loss, but other related forms of dietary fiber, including guar gum and psyllium, are ineffective.

  8. The Role of Energy Flux in Weight Management

    OpenAIRE

    Clemens Drenowatz; Klaus Greier

    2017-01-01

    Excess body weight has been identified as one of the leading threats to public health. In addition to health concerns at the individual level, the increased medical costs put a significant burden on the health care system. Even though an imbalance between energy intake and energy expenditure is ultimately responsible for changes in body weight and body composition such a simple opposition does not reflect the complex interaction of various contributors to energy balance. The limited understan...

  9. The performance of broiler finisher birds fed varying levels of feather ...

    African Journals Online (AJOL)

    The performance of broiler finisher birds fed varying levels of feather meal as replacement for soya bean meal. ... meal increased, feed cost/ kg weight gain increased and both differed significantly (P<0.05) between treatment means, while the birds tolerated feather meal up to 7.5% inclusion level, 2.5% was the optimal.

  10. Impact of Formulas, Language and Instruction on Student Performance on Cost-Volume-Profit Problems

    Science.gov (United States)

    Johnson, Benny G.; Sargent, Carol Springer

    2014-01-01

    This study investigated how three factors impacted performance on cost-volume-profit homework problems: language, formula use, and instruction. Students enrolled in Introduction to Financial Accounting (the first principles of accounting course) and Managerial Accounting (the second principles of accounting course) from eight different US colleges…

  11. Literature Review of Shear Performance of Light-weight Steel Framing Wall Panels

    Science.gov (United States)

    Zhang, Zhuangnan; Liu, Shen; Liu, Hong

    2018-03-01

    In this paper, a comprehensive review of light-weight steel framing wall panels was carried out. The structure and force characteristics of light-weight steel framing wall panels were introduced. The testing and theoretical research results on the shear behaviour of light-weight steel framing wall panels were summarized in the domestic and foreign. And combined with the existing standards in China, the author's views and ideas are put forward to the problems in the research field of this kind of structural system.

  12. Weighted OFDM for wireless multipath channels

    DEFF Research Database (Denmark)

    Prasad, Ramjee; Nikookar, H.

    2000-01-01

    In this paper the novel method of "weighted OFDM" is addressed. Different types of weighting factors (including Rectangular, Bartlett, Gaussian. Raised cosine, Half-sin and Shanon) are considered. The impact of weighting of OFDM on the peak-to-average power ratio (PAPR) is investigated by means...... of simulation and is compared for the above mentioned weighting factors. Results show that by weighting of the OFDM signal the PAPR reduces. Bit error performance of weighted multicarrier transmission over a multipath channel is also investigated. Results indicate that there is a trade off between PAPR...

  13. Effect of Tactile-Kinesthetic Stimulation on Weight Gaining of Preterm Infants

    Directory of Open Access Journals (Sweden)

    Mahdi Basiry

    2009-11-01

    Full Text Available Background:The quality of life and standard of health care in a society is measured  by its preterm infants' mortality rate. The popularity and credibility of alternative treatment such as touch therapy may be effective in preterm and low birth weightinfants in order to increase their survival rate.The aim of this study was to determine the effect of touch intervention on the weight gain of preterm infants who were admitted to the Neonatal Intensive Care Unite(NICU. Methods:This study was a randomized controlled trial performed in NICU of  Emamreza hospital,Mashhad,Iran,from July 2007 to November 2007. There were two groups (the control group and the case group and one response variable (weight gain.Infants in the control group received routine nursing care. Infants in the case  group,in addition to the routine care,received stroking/passive limb movement therapy  for three 15 minute sessions per day for a 10 day period.Then weight gaining was compared between the two groups .  Results:The weight gain data was analyzed by SPSS software. Over the 10 day study period, the case group gained significantly more weight compared to the control  group (p(p<0.001(.Conclusion:The data suggest that stroking/passive limb movement can be an efficientand cost effective way of enhancing growth in stable preterm infants .

  14. Assessing Cost-Effectiveness in Obesity (ACE-Obesity: an overview of the ACE approach, economic methods and cost results

    Directory of Open Access Journals (Sweden)

    Swinburn Boyd

    2009-11-01

    Full Text Available Abstract Background The aim of the ACE-Obesity study was to determine the economic credentials of interventions which aim to prevent unhealthy weight gain in children and adolescents. We have reported elsewhere on the modelled effectiveness of 13 obesity prevention interventions in children. In this paper, we report on the cost results and associated methods together with the innovative approach to priority setting that underpins the ACE-Obesity study. Methods The Assessing Cost Effectiveness (ACE approach combines technical rigour with 'due process' to facilitate evidence-based policy analysis. Technical rigour was achieved through use of standardised evaluation methods, a research team that assembles best available evidence and extensive uncertainty analysis. Cost estimates were based on pathway analysis, with resource usage estimated for the interventions and their 'current practice' comparator, as well as associated cost offsets. Due process was achieved through involvement of stakeholders, consensus decisions informed by briefing papers and 2nd stage filter analysis that captures broader factors that influence policy judgements in addition to cost-effectiveness results. The 2nd stage filters agreed by stakeholders were 'equity', 'strength of the evidence', 'feasibility of implementation', 'acceptability to stakeholders', 'sustainability' and 'potential for side-effects'. Results The intervention costs varied considerably, both in absolute terms (from cost saving [6 interventions] to in excess of AUD50m per annum and when expressed as a 'cost per child' estimate (from Conclusion The use of consistent methods enables valid comparison of potential intervention costs and cost-offsets for each of the interventions. ACE-Obesity informs policy-makers about cost-effectiveness, health impact, affordability and 2nd stage filters for important options for preventing unhealthy weight gain in children. In related articles cost-effectiveness results and

  15. Position of the American Dietetic Association: weight management.

    Science.gov (United States)

    Seagle, Helen M; Strain, Gladys Witt; Makris, Angela; Reeves, Rebecca S

    2009-02-01

    It is the position of the American Dietetic Association that successful weight management to improve overall health for adults requires a lifelong commitment to healthful lifestyle behaviors emphasizing sustainable and enjoyable eating practices and daily physical activity. Given the increasing incidence of overweight and obesity along with the escalating health care costs associated with weight-related illnesses, health care providers must discover how to effectively treat this complex condition. Food and nutrition professionals should stay current and skilled in weight management to assist clients in preventing weight gain, optimizing individual weight loss interventions, and achieving long-term weight loss maintenance. Using the American Dietetic Association's Evidence Analysis Process and Evidence Analysis Library, this position paper presents the current data and recommendations for weight management. The evidence supporting the value of portion control, eating frequency, meal replacements, and very-low-energy diets are discussed as well as physical activity, behavior therapy, pharmacotherapy, and surgery. Public policy changes to create environments that can assist all populations to achieve and sustain healthful lifestyle behaviors are also reviewed.

  16. Performance and cost of energy transport and storage systems for dish applications using reversible chemical reactions

    Science.gov (United States)

    Schredder, J. M.; Fujita, T.

    1984-01-01

    The use of reversible chemical reactions for energy transport and storage for parabolic dish networks is considered. Performance and cost characteristics are estimated for systems using three reactions (sulfur-trioxide decomposition, steam reforming of methane, and carbon-dioxide reforming of methane). Systems are considered with and without storage, and in several energy-delivery configurations that give different profiles of energy delivered versus temperature. Cost estimates are derived assuming the use of metal components and of advanced ceramics. (The latter reduces the costs by three- to five-fold). The process that led to the selection of the three reactions is described, and the effects of varying temperatures, pressures, and heat exchanger sizes are addressed. A state-of-the-art survey was performed as part of this study. As a result of this survey, it appears that formidable technical risks exist for any attempt to implement the systems analyzed in this study, especially in the area of reactor design and performance. The behavior of all components and complete systems under thermal energy transients is very poorly understood. This study indicates that thermochemical storage systems that store reactants as liquids have efficiencies below 60%, which is in agreement with the findings of earlier investigators.

  17. High efficiency motors - performance, economy and reliability, by optimisation

    Energy Technology Data Exchange (ETDEWEB)

    Caselotti, P.; Conchetto, A.; Tavner, P.J.

    2000-07-01

    The challenge of the efficiency initiatives in North America and the European Union is to improve performance without reducing power-weight by adding materials and increasing cost. This has been the subject of other papers, Haataja et al Ref2, where the key area has been identified as reducing loss. This paper suggests that addressing the fundamental problem of heat transfer in the TEFC machine, in addition to reducing loss will make it possible to improve performance and still provide competitive products. (orig.)

  18. Early and extraordinary peaks in physical performance come with a longevity cost

    DEFF Research Database (Denmark)

    van de Vijver, Paul L; van Bodegom, David; Westendorp, Rudi G J

    2016-01-01

    Life history theory postulates a trade-off between development and maintenance. This trade-off is observed when comparing life histories of different animal species. In humans, however, it is debated if variation in longevity is explained by differences in developmental traits. Observational...... studies found a trade-off between early and high fecundity and longevity in women. Development encompasses more than fecundity and also concerns growth and physical performance. Here, we show a life history trade-off between early and above average physical performance and longevity in male Olympic...... suffered a 4.7-year longevity cost. (95% CI 2.1-7.5 years, p=0.001). This is the first time a life history trade-off between physical performance and longevity has been found in humans. This finding deepens our understanding of early developmental influences on the variation of longevity in humans....

  19. Cesarean deliveries and maternal weight retention.

    Science.gov (United States)

    Kapinos, Kandice A; Yakusheva, Olga; Weiss, Marianne

    2017-10-04

    Cesarean delivery accounts for nearly one-third of all births in the U.S. and contributes to an additional $38 billion in healthcare costs each year. Although Cesarean delivery has a long record of improving maternal and neonatal mortality and morbidity, increased utilization over time has yielded public health concerns and calls for reductions. Observational evidence suggests Cesarean delivery is associated with increased maternal postpartum weight, which may have significant implications for the obesity epidemic. Previous literature, however, typically does not address selection biases stemming from correlations of pre-pregnancy weight and reproductive health with Cesarean delivery. We used fetal malpresentation as a natural experiment as it predicts Cesarean delivery but is uncorrelated with pre-pregnancy weight or maternal health. We used hospital administrative data (including fields used in vital birth record) from the state of Wisconsin from 2006 to 2013 to create a sample of mothers with at least two births. Using propensity score methods, we compared maternal weight prior to the second pregnancy of mothers who delivered via Cesarean due to fetal malpresentation to mothers who deliver vaginally. We found no evidence that Cesarean delivery in the first pregnancy causally leads to greater maternal weight, BMI, or movement to a higher BMI classification prior to the second pregnancy. After accounting for correlations between pre-pregnancy weight, gestational weight gain, and mode of delivery, there is no evidence of a causal link between Cesarean delivery and maternal weight retention.

  20. JT8D and JT9D jet engine performance improvement program. Task 1: Feasibility analysis

    Science.gov (United States)

    Gaffin, W. O.; Webb, D. E.

    1979-01-01

    JT8D and JT9D component performance improvement concepts which have a high probability of incorporation into production engines were identified and ranked. An evaluation method based on airline payback period was developed for the purpose of identifying the most promising concepts. The method used available test data and analytical models along with conceptual/preliminary designs to predict the performance improvements, weight, installation characteristics, cost for new production and retrofit, maintenance cost, and qualitative characteristics of candidate concepts. These results were used to arrive at the concept payback period, which is the time required for an airline to recover the investment cost of concept implementation.

  1. How recalibration method, pricing, and coding affect DRG weights

    Science.gov (United States)

    Carter, Grace M.; Rogowski, Jeannette A.

    1992-01-01

    We compared diagnosis-related group (DRG) weights calculated using the hospital-specific relative-value (HSR V) methodology with those calculated using the standard methodology for each year from 1985 through 1989 and analyzed differences between the two methods in detail for 1989. We provide evidence suggesting that classification error and subsidies of higher weighted cases by lower weighted cases caused compression in the weights used for payment as late as the fifth year of the prospective payment system. However, later weights calculated by the standard method are not compressed because a statistical correlation between high markups and high case-mix indexes offsets the cross-subsidization. HSR V weights from the same files are compressed because this methodology is more sensitive to cross-subsidies. However, both sets of weights produce equally good estimates of hospital-level costs net of those expenses that are paid by outlier payments. The greater compression of the HSR V weights is counterbalanced by the fact that more high-weight cases qualify as outliers. PMID:10127456

  2. Low cost sic coated erosion resistant graphite

    International Nuclear Information System (INIS)

    Zafar, M.F.; Nicholls, J.R.

    2007-01-01

    The development of materials with unique and improved properties using low cost processes is essential to increase performance and reduce cost of the solid rocket motors. Specifically advancements are needed for boost phase nozzle. As these motors operate at very high pressure and temperatures, the nozzle must survive high thermal stresses with minimal erosion to maintain performance. Currently three material choices are being exploited; which are refractory metals, graphite and carbon-carbon composites. Of these three materials graphite is the most attractive choice because of its low cost, light weight, and easy forming. However graphite is prone to erosion, both chemical and mechanical, which may affect the ballistic conditions and mechanical properties of the nozzle. To minimize this erosion high density graphite is usually preferred; which is again very expensive. Another technique used to minimize the erosion is Pyrolytic Graphite (PG) coating inside the nozzle. However PG coating is prone to cracking and spallation along with very cumbersome deposition process. Another possible methodology to avoid this erosion is to convert the inside surface of the rocket nozzle to Silicon Carbide (SiC), which is very erosion resistant and have much better thermal stability compared to graphite and even PG. Due to its functionally gradient nature such a layer will be very adherent and resistant to spallation. The current research is focused on synthesizing, characterizing and oxidation testing of such a converted SiC layer on commercial grade graphite. (author)

  3. Solitary pulmonary nodules: cost-savings indicated by Australian experience with FDG-PET

    International Nuclear Information System (INIS)

    Keith, C.J.; Miles, K.A.; Pitman, A.G.; Hicks, R.J.

    2002-01-01

    Full text: To date, decision tree analyses demonstrating the cost-effectiveness of PET in Australia have been constrained by the need to use overseas values for diagnostic performance and disease prevalence. This study uses Australian PET experience to estimate the cost-savings produced by incorporation of FDG-PET into diagnostic algorithms for characterisation of solitary pulmonary nodules (SPNs). Values for disease prevalence and diagnostic accuracy of PET from a combined series of 89 SPNs from the Wesley Hospital and Peter MacCallum Cancer Institute were applied to two previously published decision tree models. Procedure costs were derived from the Medicare Benefits Schedule and DRG Cost Weights for Australian public hospitals. A cost of $1200 was assigned to PET. Sensitivity analyses evaluated the effect of disease prevalence and PET cost on the cost savings produced by each strategy. The values for disease prevalence (0.54), PET sensitivity (92%) and specificity (95%) from the combined series indicated cost savings per patient of $774 and $554 for the two decision trees. PET would remain cost-saving for values of prevalence up to 0.90 and 0.76, and PET costs of $1974 and $1967, for each model respectively. FDG-PET evaluation of SPNs would produce cost-savings within Australia even with substantial variations in disease prevalence and PET costs. Copyright (2002) Blackwell Science Pty Ltd

  4. Performance evaluation of an algorithm for fast optimization of beam weights in anatomy-based intensity modulated radiotherapy

    International Nuclear Information System (INIS)

    Ranganathan, Vaitheeswaran; Sathiya Narayanan, V.K.; Bhangle, Janhavi R.; Gupta, Kamlesh K.; Basu, Sumit; Maiya, Vikram; Joseph, Jolly; Nirhali, Amit

    2010-01-01

    This study aims to evaluate the performance of a new algorithm for optimization of beam weights in anatomy-based intensity modulated radiotherapy (IMRT). The algorithm uses a numerical technique called Gaussian-Elimination that derives the optimum beam weights in an exact or non-iterative way. The distinct feature of the algorithm is that it takes only fraction of a second to optimize the beam weights, irrespective of the complexity of the given case. The algorithm has been implemented using MATLAB with a Graphical User Interface (GUI) option for convenient specification of dose constraints and penalties to different structures. We have tested the numerical and clinical capabilities of the proposed algorithm in several patient cases in comparison with KonRad inverse planning system. The comparative analysis shows that the algorithm can generate anatomy-based IMRT plans with about 50% reduction in number of MUs and 60% reduction in number of apertures, while producing dose distribution comparable to that of beamlet-based IMRT plans. Hence, it is clearly evident from the study that the proposed algorithm can be effectively used for clinical applications. (author)

  5. Establishment of design and performance requirements using cost and systems analysis

    International Nuclear Information System (INIS)

    Waganer, L.M.; Carosella, L.A.; Defreece, D.A.

    1977-01-01

    The current uncertainty in design approach and performance requirements for a commercial fusion power plant poses a problem for the designer in configuring the plant and for the utilities in analyzing the attractiveness of a future fusion power plant. To provide direction and insight in this area, a systems analysis model was constructed at McDonnell Douglas, utilizing fusion subsystem algorithms with subsystem cost estimating relationships into a self-consistent computerized model for several fusion reactor concepts. Cost estimating data has been compiled by utilizing McDonnell Douglas' experience in fabricating large, complex metal assemblies and soliciting the accumulated store of knowledge in existing power plants and new emerging technologies such as the Clinch River Breeder Reactor. Using the computer model, sensitivities to plasma, reactor and plant parameters are a few of the options that have been evaluated to yield recommended concepts/techniques/solutions. This is a very beneficial tool in assessing the impact of the fusion reactor on the electrical power community and charting the optimum developmental approach

  6. Gasification Plant Cost and Performance Optimization

    Energy Technology Data Exchange (ETDEWEB)

    Samuel Tam; Alan Nizamoff; Sheldon Kramer; Scott Olson; Francis Lau; Mike Roberts; David Stopek; Robert Zabransky; Jeffrey Hoffmann; Erik Shuster; Nelson Zhan

    2005-05-01

    As part of an ongoing effort of the U.S. Department of Energy (DOE) to investigate the feasibility of gasification on a broader level, Nexant, Inc. was contracted to perform a comprehensive study to provide a set of gasification alternatives for consideration by the DOE. Nexant completed the first two tasks (Tasks 1 and 2) of the ''Gasification Plant Cost and Performance Optimization Study'' for the DOE's National Energy Technology Laboratory (NETL) in 2003. These tasks evaluated the use of the E-GAS{trademark} gasification technology (now owned by ConocoPhillips) for the production of power either alone or with polygeneration of industrial grade steam, fuel gas, hydrocarbon liquids, or hydrogen. NETL expanded this effort in Task 3 to evaluate Gas Technology Institute's (GTI) fluidized bed U-GAS{reg_sign} gasifier. The Task 3 study had three main objectives. The first was to examine the application of the gasifier at an industrial application in upstate New York using a Southeastern Ohio coal. The second was to investigate the GTI gasifier in a stand-alone lignite-fueled IGCC power plant application, sited in North Dakota. The final goal was to train NETL personnel in the methods of process design and systems analysis. These objectives were divided into five subtasks. Subtasks 3.2 through 3.4 covered the technical analyses for the different design cases. Subtask 3.1 covered management activities, and Subtask 3.5 covered reporting. Conceptual designs were developed for several coal gasification facilities based on the fluidized bed U-GAS{reg_sign} gasifier. Subtask 3.2 developed two base case designs for industrial combined heat and power facilities using Southeastern Ohio coal that will be located at an upstate New York location. One base case design used an air-blown gasifier, and the other used an oxygen-blown gasifier in order to evaluate their relative economics. Subtask 3.3 developed an advanced design for an air

  7. Design and fabrication of light weight current collectors for direct methanol fuel cells using the micro-electro mechanical system technique

    Science.gov (United States)

    Sung, Min-Feng; Kuan, Yean-Der; Chen, Bing-Xian; Lee, Shi-Min

    The direct methanol fuel cell (DMFC) is suitable for portable applications. Therefore, a light weight and small size is desirable. The main objective of this paper is to design and fabricate a light weight current collector for DMFC usage. The light weight current collector mainly consists of a substrate with two thin film metal layers. The substrate of the current collector is an FR4 epoxy plate. The thin film metal layers are accomplished by the thermo coater technique to coat metal powders onto the substrate surfaces. The developed light weight current collectors are further assembled to a single cell DMFC test fixture to measure the cell performance. The results show that the proposed current collectors could even be applied to DMFCs because they are light, thin and low cost and have potential for mass production.

  8. A study on body-weight perception, future intention and weight-management behaviour among normal-weight, overweight and obese women in India.

    Science.gov (United States)

    Agrawal, Praween; Gupta, Kamla; Mishra, Vinod; Agrawal, Sutapa

    2014-04-01

    We examined the socio-economic differential in the self-perception of body weight, future intention for weight management and actual weight-management behaviour among normal-weight, overweight and obese women in India. A population-based follow-up survey of ever-married women, systematically selected from the second round of the National Family Health Survey (NFHS-2, 1998-99) samples, who were re-interviewed after four years in 2003. Information on women's perception about their own weight, intention of weight management and actual weight-management behaviour were collected through personal interview. Anthropometric measurements were obtained from women to compute their current BMI. Three hundred and twenty-five ever-married women aged 20-54 years residing in the national capital territory of Delhi in India. Discrepancy between self-perceived body weight and women's actual body weight was reported. One-quarter of overweight women and one in ten obese women perceived themselves as normal weight. Although a majority of overweight and obese women wanted to reduce their weight, a significant proportion of overweight (one in four) and 4 % of obese women also wanted to maintain their weight as it is. Only one in three overweight and one in four obese women were performing any physical activity to reduce their weight. These findings are important for public health interventions in obesity care. Implementation of health promotion and health education in the community should use effective school education and mass-media programmes to raise awareness of appropriate body weight to combat the growing level of obesity among Indian women.

  9. PERFORMANCE OF MASHONA COWS REARED ON NATURAL RANGELANDS WITH NON-CONVENTIONAL PROTEIN SUPPLEMENTATION IN THE DRY SEASON, ZIMBABWE

    Directory of Open Access Journals (Sweden)

    Jacob Gusha

    2015-12-01

    Full Text Available Performance of animals in smallholder farming systems is hindered by feed availability and feed costs that make up 60-70% of total variable cost in a farming system. The use of non-conventional feedstuffs is an alternative which can be adopted to minimize feeding costs. The study was conducted to evaluate performance of animals fed with supplements formulated on-farm in comparison with a commercial prepared supplement. Thirty Mashona cows were grouped according to age and subjected to five treatments, given twice a week from the 1st of September until 31st December for three subsequent years. The five treatment diets, beef survival meal (BSM, urea treated maize stover (UTS, Leucaena leucocephala meal (LLM, mixed forage meal (MFM and natural pastures (NP were randomly assigned to cows in a complete randomised design (CRD. Average weight gains were determined. Performance in the first year was not significantly different across treatments. In the subsequent years, performance remained low in the NP. Average weight gains increased in the second and third years and was significantly different across treatments (P<0.05. Performance of animals supplemented with non-conventional feed was comparable to those offered commercial BFM; hence LLM and UTS can be used as alternative protein supplements especially in resource-constrained farming systems. Â

  10. Extracting surface waves, hum and normal modes: time-scale phase-weighted stack and beyond

    Science.gov (United States)

    Ventosa, Sergi; Schimmel, Martin; Stutzmann, Eleonore

    2017-10-01

    Stacks of ambient noise correlations are routinely used to extract empirical Green's functions (EGFs) between station pairs. The time-frequency phase-weighted stack (tf-PWS) is a physically intuitive nonlinear denoising method that uses the phase coherence to improve EGF convergence when the performance of conventional linear averaging methods is not sufficient. The high computational cost of a continuous approach to the time-frequency transformation is currently a main limitation in ambient noise studies. We introduce the time-scale phase-weighted stack (ts-PWS) as an alternative extension of the phase-weighted stack that uses complex frames of wavelets to build a time-frequency representation that is much more efficient and fast to compute and that preserve the performance and flexibility of the tf-PWS. In addition, we propose two strategies: the unbiased phase coherence and the two-stage ts-PWS methods to further improve noise attenuation, quality of the extracted signals and convergence speed. We demonstrate that these approaches enable to extract minor- and major-arc Rayleigh waves (up to the sixth Rayleigh wave train) from many years of data from the GEOSCOPE global network. Finally we also show that fundamental spheroidal modes can be extracted from these EGF.

  11. Cost, Schedule, And Performance Elements For Comparison of Hydrodynamic Models of Near-Surface Unmanned Underwater Vehicle Operations

    Science.gov (United States)

    2017-12-01

    2-89) Prescribed by ANSI Std. 239-18 ii THIS PAGE INTENTIONALLY LEFT BLANK iii Approved for public release. Distribution is unlimited. COST ...from the scope of this demonstration due to time constraints. Further study of this software would benefit similar cost , schedule, and performance...NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA SYSTEMS ENGINEERING CAPSTONE PROJECT REPORT Approved for public release. Distribution

  12. The IMPACT Common Module - A Low Cost, Reconfigurable Building Block for Next Generation Phased Arrays

    Science.gov (United States)

    2016-03-31

    Road NE Cedar Rapids, IA USA 52498 Ted.Hoffmann@corp.rockwellcollins.com Caleb Fulton, Mark Yeary, Austin Saunders, Dan Thompson University...thus providing increasing functionality and