WorldWideScience

Sample records for pcm accidents

  1. PCM Concrete. [Phase Change Materials

    Energy Technology Data Exchange (ETDEWEB)

    Juul Andersen, T. [Danish Technological Institute, Taastrup (Denmark); Poulsen, H.-H. [BASF A/S, Roedekro (Denmark); Passov, F. [Spaencom A/S, Hedehusene (Denmark); Heiselberg, P. [Aalborg Univ..Aalborg (Denmark)

    2013-04-01

    PCM-Concrete was a research and development project launched in 2009 and finished in 2012. The project, which was funded by The Danish National Advanced Technology Foundation, had a total budget of 1.7 million Euros and included 4 partners: Danish Technological Institute (project manager), Aalborg University, BASF A/S and Spaencom A/S. The overall vision of the project was to reduce energy consumption for heating and cooling in buildings by developing high-performance concrete structures microencapsulated Phase Change Materials (PCM). The PCM used in the project was Micronal produced by BASF A/S. Micronal is small capsules with an acrylic shell and inside a wax with a melting point at approx. 23 deg. C equal to a comfortable indoor temperature. During the melting process thermal energy is transferred to chemical reaction (melting/solidification) depending on PCM being heated up or cooled down. Adding Micronal to concrete would theoretically increase the thermal mass of the concrete and improve the diurnal heat capacity which is the amount of energy that can be stored and released during 24 hours. Nevertheless, it is a relatively new technology that has not received much attention, yet. In the PCM-Concrete project 5 main investigations were carried out: 1) Development of concrete mix design with PCM. 2) Investigation of thermal properties of the PCM concrete: thermal conductivity, specific heat capacity, density. 3) Up-scaling the research to industrial production of PCM-concrete structures. 4) Testing energy efficiency in full scale. 5) Confronting aesthetic and acoustic barriers to full exploitation of the potential of PCM-concrete structures. The results from the test program showed: 1) That the diurnal heat storage capacity is higher for all 4 hollow core decks with tiles attached compared to the reference hollow core deck. 2) The hollow core decks with concrete tiles without PCM performs slightly better than the tiles with PCM. 3) That is was impossible to

  2. PCM power - Final report; Power PCM - Rapport final

    Energy Technology Data Exchange (ETDEWEB)

    Citherlet, S.; Bony, J.; Morel, J.

    2008-07-01

    In a previous project (COSY-PCM) performed within Task 32 of the Solar Heating and Cooling Program of the International Energy Agency (IEA), we had analyzed the potential of energy storage by using phase-change materials (PCM) immersed in the tank of a combined solar heating system for space heating and domestic hot water. The potential of PCM use seemed to be highly dependent on the power of the equipment involved. If the power is too high the PCM is not able to store and to return the heat it should, due to the poor thermal conductivity of this type of material, even if a mixture of sodium acetate and graphite is used. The aim of the reported follow-up project was to develop nomographs for a fast and easy dimensioning of a water storage tank using phase-change materials (paraffin and sodium acetate with graphite) as a function of heat load, storage volume, and diameter of the PCM modules. For this purpose we have: (i) performed a measurement campaign on a new storage tank; (ii) developed a mathematical model of the installation under investigation, based upon the model previously developed for the description of the behaviour of the PCM; (iii) validated the model with experimental results; (iv) performed a series of simulations to create the nomographs. We have also studied the environmental impacts of sodium acetate. (author)

  3. CEPRAM: Compression for Endurance in PCM RAM

    OpenAIRE

    González Alberquilla, Rodrigo; Castro Rodríguez, Fernando; Piñuel Moreno, Luis; Tirado Fernández, Francisco

    2017-01-01

    We deal with the endurance problem of Phase Change Memories (PCM) by proposing Compression for Endurance in PCM RAM (CEPRAM), a technique to elongate the lifespan of PCM-based main memory through compression. We introduce a total of three compression schemes based on already existent schemes, but targeting compression for PCM-based systems. We do a two-level evaluation. First, we quantify the performance of the compression, in terms of compressed size, bit-flips and how they are affected by e...

  4. Testing of the Eberline PCM-2

    International Nuclear Information System (INIS)

    Howe, K.L.

    1994-01-01

    The PCM-2 manufactured by Eberline Instruments is a whole body monitor that detects both alpha and beta contamination. The PCM-2 uses an IBM compatible personal computer for all software functions. The PCM-2 has 34 large area detectors which can cover approximately 40% of the body at a time. This requires two counting cycles to cover approximately 80% of the body. With the normal background seen at Rocky Flats, each count time takes approximately 15--20 seconds. There are a number of beta and gamma whole body monitors available from different manufacturers, but an alpha whole body monitor is a rarity. Because of the need for alpha whole body monitors at The Rocky Flats Environmental Technology Site, it was decided to do thorough testing on the PCM-2. A three month test was run in uranium building and a three month test in a plutonium building to verify the alpha capabilities of the PCM-2

  5. Heat pipe with PCM for electronic cooling

    International Nuclear Information System (INIS)

    Weng, Ying-Che; Cho, Hung-Pin; Chang, Chih-Chung; Chen, Sih-Li

    2011-01-01

    This article experimentally investigates the thermal performances of a heat pipe with phase change material for electronic cooling. The adiabatic section of heat pipe is covered by a storage container with phase change material (PCM), which can store and release thermal energy depending upon the heating powers of evaporator and fan speeds of condenser. Experimental investigations are conducted to obtain the system temperature distributions from the charge, discharge and simultaneous charge/discharge performance tests. The parameters in this study include three kinds of PCMs, different filling PCM volumes, fan speeds, and heating powers in the PCM cooling module. The cooling module with tricosane as PCM can save 46% of the fan power consumption compared with the traditional heat pipe.

  6. Gamma sensitivity of the Eberline PCM-1

    International Nuclear Information System (INIS)

    Blanton, J.D.

    1988-01-01

    This paper reports that normally, alarm setpoints for the Eberline PCM-1 series personnel contamination monitors are calculated based upon efficiencies measured using 100-cm 2 or larger beta or mixed beta-gamma sources. This simulates the type of contamination most frequently encountered on personnel and clothing--low-level, distributed beta-gamma emitters. In most circumstances, the PCM-1's sensitivity to the other type of contamination encountered in nuclear plant work--hot particles--would be expected to be the same as, or better than, its sensitivity to distributed contamination. However, particles that are deposited on skin or clothing can be partially shielded from the view of the PCM-1's detectors. In these situations, the PCm-1's sensitivity to gamma radiation may be more relevant than its sensitivity to betas

  7. Empirical equations for viscosity and specific heat capacity determination of paraffin PCM and fatty acid PCM

    Science.gov (United States)

    Barreneche, C.; Ferrer, G.; Palacios, A.; Solé, A.; Inés Fernández, A.; Cabeza, L. F.

    2017-10-01

    Phase change materials (PCM) used in thermal energy storage (TES) systems have been presented, over recent years, as one of the most effective options in energy storage. Paraffin and fatty acids are some of the most used PCM in TES systems, as they have high phase change enthalpy and in addition they do not present subcooling nor hysteresis and have proper cycling stability. The simulations and design of TES systems require the knowledge of the thermophysical properties of PCM. Thermal conductivity, viscosity, specific heat capacity (Cp) can be experimentally determined, but these are material and time consuming tasks. To avoid or to reduce them, and to have reliable data without the need of experimentation, thermal properties can be calculated by empirical equations. In this study, five different equations are given to calculate the viscosity and specific heat capacity of fatty acid PCM and paraffin PCM. Two of these equations concern, respectively, the empirical calculation of the viscosity and liquid Cp of the whole paraffin PCM family, while the other three equations presented are for the corresponding calculation of viscosity, solid Cp, liquid Cp of the whole fatty acid family of PCM. Therefore, this study summarize the work performed to obtain the main empirical equations to measure the above mentioned properties for whole fatty acid PCM family and whole paraffin PCM family. Moreover, empirical equations have been obtained to calculate these properties for other materials of these PCM groups and these empirical equations can be extrapolated for PCM with higher or lower phase change temperatures within a lower relative error 4%.

  8. Modeling of greenhouse with PCM energy storage

    International Nuclear Information System (INIS)

    Najjar, Atyah; Hasan, Afif

    2008-01-01

    Greenhouses provide a controlled environment that is suitable for plants growth and cultivation. In this paper the maximum temperature change inside the greenhouse is to be reduced by the use of energy storage in a phase change material PCM. A mathematical model is developed for the storage material and for the greenhouse. The coupled models are solved using numerical methods and Java code program. The effect of different parameters on the inside greenhouse temperature is investigated. The temperature swing between maximum and minimum values during 24 h can be reduced by 3-5 deg. C using the PCM storage. This can be improved further by enhancing the heat transfer between the PCM storage and the air inside the greenhouse

  9. Modeling of greenhouse with PCM energy storage

    Energy Technology Data Exchange (ETDEWEB)

    Najjar, Atyah [Computation Science, Birzeit University, Birzeit (PS); Hasan, Afif [Mechanical Engineering Department, Birzeit University, Birzeit (PS)

    2008-11-15

    Greenhouses provide a controlled environment that is suitable for plants growth and cultivation. In this paper the maximum temperature change inside the greenhouse is to be reduced by the use of energy storage in a phase change material PCM. A mathematical model is developed for the storage material and for the greenhouse. The coupled models are solved using numerical methods and Java code program. The effect of different parameters on the inside greenhouse temperature is investigated. The temperature swing between maximum and minimum values during 24 h can be reduced by 3-5 C using the PCM storage. This can be improved further by enhancing the heat transfer between the PCM storage and the air inside the greenhouse. (author)

  10. Potential for fuel melting and cladding thermal failure during a PCM event in LWRs

    International Nuclear Information System (INIS)

    El-Genk, M.S.; Croucher, D.W.

    1979-01-01

    The primary concern in nuclear reactor safety is to ensure that no conceivable accident, whether initiated by a failure of the reactor system or by incorrect operation, will lead to a dangerous release of radiation to the environment. A number of hypothesized off-normal power or cooling conditions, generally termed as power-cooling-mismatch (PCM) accidents, are considered in the safety analysis of light water reactors (LWRs). During a PCM accident, film boiling may occur at the cladding surface and cause a rapid temperature increase in the fuel and the cladding, perhaps producing embrittlement of the zircaloy cladding by oxidation. Molten fuel may be produced at the center of the pellets, extrude radially through open cracks in the outer, unmelted portion of the pellet and relocate in the fuel-cladding gap. If the amount of extruded molten fuel is sufficient to establish contact with the cladding, which is at a high temperature during film boiling, the zircaloy cladding may melt. The present work assesses the potential for central fuel melting and thermal failure of the zircaloy cladding due to melting upon being contacted by extruded molten UO 2 -fuel during a PCM event

  11. Energy asymmetry in melting and solidifying processes of PCM

    International Nuclear Information System (INIS)

    Jin, Xing; Hu, Huoyan; Shi, Xing; Zhang, Xiaosong

    2015-01-01

    Highlights: • The melting process and the solidifying process of PCM were asymmetrical. • The enthalpy and state of PCM were affected by its previous state. • The main reason for energy asymmetry of PCM was supercooling. - Abstract: The solidifying process of phase change material (PCM) was usually recognized as the exact inverse process of its melting process, especially when building the heat transfer model of PCM. To figure out that whether the melting process and the solidifying process of PCM were symmetrical, several kinds of PCMs were tested by a differential scanning calorimeter (DSC) in this paper. The experimental results showed that no matter using the DSC dynamic measurement method or the DSC step measurement method, the melting process and the solidifying process of PCM were asymmetrical. Because of the energy asymmetry in the melting and solidifying processes of PCM, it was also found that the enthalpy and the state of PCM were not only dependent on its temperature, but also affected by its “previous state”.

  12. Thermal Performance of the Storage Brick Containing Microencapsulated PCM

    International Nuclear Information System (INIS)

    Lee, Dong Gyu

    1998-02-01

    The utilization of microencapsulated phase change materials(PCMs) provides several advantages over conventional PCM application. The heat storage system, as well as heat recovery system, can be built to a smaller size than the normal systems for a given thermal cycling capacity. This microencapsulated PCM technique has not yet been commercialized, however. In this work sodium acetate trihydrate(CH 3 COONa · 3H 2 O) was selected for the PCM and was encapsulated. This microencapsulated PCM was mixed with cement mortar for utilization as a floor heating system. In this experiment performed here the main purpose was to investigate the thermal performance of a storage brick with microencapsulated PCM concentration. The thermal performance of this storage brick is dependent on PCM concentration, flow rate and cooling temperature of the heat transfer fluid, etc. The results showed that cycle time was shortened as the PCM content was increased and as the mass flow rate was increased. The same effect was obtained when the cooling temperature was decreased. For each thermal storage brick the overall heat transfer coefficient(U-value) was constant for a 0% brick, but was increased with time for the bricks containing microencapsulated PCM. For the same mass flow rate, as the cooling temperature decreased, the amount of heat withdrawn increased, and in particular a critical cooling temperature was found for each thermal storage brick. The average effectiveness of each thermal storage brick was found to be approximately 48%, 51% and 58% respectively

  13. Preliminary Study of Applying Phase Change Materials (PCM) for Containment Passive Cooling

    International Nuclear Information System (INIS)

    Ko, A Reum; Lee, Jeong Ik; Yoon, Ho Joon

    2016-01-01

    Most of Pressurized Water Reactor (PWR) containments use fan cooler systems and containment spray systems. However, the importance of passive safety system has increased after the Fukushima accident. As the main passive safety system, Passive Containment Cooling System (PCCS), which utilizes natural phenomena to remove the heat released from the reactor, is suggested in the advanced pressurized water reactor (APWR). To increase the efficiency of passive cooling, additional passive containment cooling method using Phase Change Material (PCM) is suggested in this paper. For containment using PCMs, there are many advantages. Phase Change Material (PCM) is proposed as an additional passive containment cooling method to increase the efficiency of passive cooling in this paper. To apply proper PCMs to containment, commercially available PCMs were screened while reviewing thermophysical properties data and suggested selection criteria. A sensitivity study was also carried out to identify the effect of potential installation location of PCM using the CAP code. The pressure of containment in most cases showed slightly higher than that of the initial case. For the temperature of steam and water and humidity, similar results with the initial case were showed in most cases

  14. Preliminary Study of Applying Phase Change Materials (PCM) for Containment Passive Cooling

    Energy Technology Data Exchange (ETDEWEB)

    Ko, A Reum; Lee, Jeong Ik [KAIST, Daejeon (Korea, Republic of); Yoon, Ho Joon [KUSTAR, Abu Dhabi (United Arab Emirates)

    2016-05-15

    Most of Pressurized Water Reactor (PWR) containments use fan cooler systems and containment spray systems. However, the importance of passive safety system has increased after the Fukushima accident. As the main passive safety system, Passive Containment Cooling System (PCCS), which utilizes natural phenomena to remove the heat released from the reactor, is suggested in the advanced pressurized water reactor (APWR). To increase the efficiency of passive cooling, additional passive containment cooling method using Phase Change Material (PCM) is suggested in this paper. For containment using PCMs, there are many advantages. Phase Change Material (PCM) is proposed as an additional passive containment cooling method to increase the efficiency of passive cooling in this paper. To apply proper PCMs to containment, commercially available PCMs were screened while reviewing thermophysical properties data and suggested selection criteria. A sensitivity study was also carried out to identify the effect of potential installation location of PCM using the CAP code. The pressure of containment in most cases showed slightly higher than that of the initial case. For the temperature of steam and water and humidity, similar results with the initial case were showed in most cases.

  15. Diurnal thermal analysis of microencapsulated PCM-concrete composite walls

    International Nuclear Information System (INIS)

    Thiele, Alexander M.; Sant, Gaurav; Pilon, Laurent

    2015-01-01

    Highlights: • Transient heat conduction across microencapsulated PCM-concrete walls was simulated. • Equivalent homogeneous wall with effective thermal properties was rigorously derived. • Adding PCM to the wall increases daily energy savings and delays peak thermal load. • Energy savings is maximum when PCM melting temperature equals indoor temperature. • Energy savings are limited in extreme climates but time delay can be large. - Abstract: This paper examines the benefits of adding microencapsulated phase change material (PCM) to concrete used in building envelopes to reduce energy consumption and costs. First, it establishes that the time-dependent thermal behavior of microencapsulated PCM-concrete composite walls can be accurately predicted by an equivalent homogeneous wall with appropriate effective thermal properties. The results demonstrate that adding microencapsulated PCM to concrete resulted in a reduction and a time-shift in the maximum heat flux through the composite wall subjected to diurnal sinusoidal outdoor temperature and solar radiation heat flux. The effects of the PCM volume fraction, latent heat of fusion, phase change temperature and temperature window, and outdoor temperature were evaluated. Several design rules were established including (i) increasing the PCM volume fraction and/or enthalpy of phase change increased the energy flux reduction and the time delay, (ii) the energy flux reduction was maximized when the PCM phase change temperature was close to the desired indoor temperature, (iii) the optimum phase change temperature to maximize the time delay increased with increasing average outdoor temperature, (iv) in extremely hot or cold climates, the thermal load could be delayed even though the reduction in daily energy flux was small, and (v) the choice of phase change temperature window had little effect on the energy flux reduction and on the time delay. This analysis can serve as a framework to design PCM composite walls

  16. Building integration of PCM for natural cooling of buildings

    International Nuclear Information System (INIS)

    Álvarez, Servando; Cabeza, Luisa F.; Ruiz-Pardo, Alvaro; Castell, Albert; Tenorio, José Antonio

    2013-01-01

    Highlights: ► A brief overview of PCM solutions for buildings is provided. ► Some weaknesses of existing PCM solutions for buildings were identified. ► New solutions for PCM integration in buildings are proposed. ► Proposed solutions overcome identified weaknesses of existing solutions. - Abstract: The use of night cooling ventilation in addition of phase change materials (PCMs) is a very powerful strategy for reducing the cooling demand of buildings. Nevertheless, there are inherent drawbacks in the way things have been doing so far: (a) The limited area of contact between PCM and the air; (b) the very low convective heat transfer coefficients which prevents the use of significant amounts of PCM and (c) the very low utilization factor of the cool stored due to the large phase shift between the time when cool is stored and time when it is required by the building. In this paper, we present innovative solutions using PCM to overcome the above situation. Compared with existing solutions, innovative solutions proposed, increase the contact area between PCM and air by a factor of approximately 3.6, increase the convective heat transfer coefficient significantly, and improve the utilization factor due to the inclusion of active control systems which allow the cold stored be actually used when required

  17. Mechanical Design of Military Communication Satellite X-band PCM

    Directory of Open Access Journals (Sweden)

    Hyung Je Woo

    1998-12-01

    Full Text Available Before an actual military communications satellite is designed and constructed, a feasibility study should take place. The basic functions of such system can be observed and demonstrated in an X-Band payload simulator. For this purpose a Payload Concept Model (PCM for X-Band payload subsystem has been developed to simulate the workings of an actual military communications payload. This paper explains and illustrates the mechanical design, manufacture, and integration of the PCM. Basic RF tests also have been performed in order to verify the design requirement of the system. The results demonstrate successful development of the PCM and operation without RF losses.

  18. Experimental investigation of inserts configurations and PCM type on the thermal performance of PCM based heat sinks

    International Nuclear Information System (INIS)

    Mahmoud, Saad; Tang, Aaron; Toh, Chin; AL-Dadah, Raya; Soo, Sein Leung

    2013-01-01

    Highlights: • Inclusion of PCM can reduce heating rate and peak temperatures of the heat sinks. • Increasing the number of fins can enhance heat transfer to PCM. • Honeycomb inserts can replace machined fin structures in PCM based heat sinks. • PCMs with lower melting points produced lower heat sink operating temperatures. - Abstract: Efficient thermal management in portable electronic devices is necessary to ensure sufficiently low operating temperatures for reliability, increased installed functions, and user comfort. Using Phase Change Materials (PCMs) based heat sinks offers potential in these applications. However, PCMs generally suffer from low thermal conductivities; therefore it is important to enhance their thermal conductivity and improve cooling performance. This study presents experimental investigation of the effects of PCM material, heat sink designs and power levels on PCM based heat sinks performance for cooling electronic devices. Six PCMs were used including paraffin wax (as reference material), two materials based on mixture of inorganic hydrated salts, two materials based on mixture of organic substances and one material based on a mixture of both organic and inorganic materials. Also, six heat sink designs were tested: one with single cavity, two with parallel fin arrangement, two with cross fin arrangement, and one with honeycomb insert inside the single cavity. Heat sinks thermal performance was investigated using paraffin wax type PCM with power inputs ranging from 3 W to 5 W. Results showed that the inclusion of PCM can reduce heating rates and peak temperatures of heat sinks with increasing the number of fins can enhance heat distribution to PCM leading to lower heat sinks peak temperatures. Also, the use of honeycomb inserts to replace machined finned structures has shown comparable thermal performance. Regarding the PCM type, the material with the lowest melting temperature has shown the best performance in terms of lowest

  19. Assessment of PCM in building climate systems; Beoordeling PCM in gebouwklimatisering

    Energy Technology Data Exchange (ETDEWEB)

    Schmitz, H. [Verwol Klimatplafonds, Delft (Netherlands)

    2005-09-01

    Insight is given into the impact of phase change materials on the indoor climate in two different types of public buildings (circus tent and a theatre) [Dutch] Organisatoren van 'een dag van autarkische systemen' vragen zich af of deze technische bijeenkomst in een geisoleerde (mobiele) circustent of een monumentaal (statisch) theater moet worden gehouden en of deze dag 's zomers of 's winters moet plaatshebben. De beantwoording vraagt om inzicht in de dimensionering van het vermogen en de capaciteit en het jaarlijks energiegebruik met en zonder PCM (phase change materials)

  20. 2014 Global Conference on Polymer and Composite Materials (PCM 2014)

    Science.gov (United States)

    2014-08-01

    The 2014 Global Conference on Polymer and Composite Materials (PCM 2014) sponsored by Ningbo Adhesives and Products Industry Association, Shanghai Bonding Technology Association, Zhejiang Bonding Technology Association, Wuhan Bonding Technology Association, Hebei Bonding and Coatings Association and Polyurethane Industry Association was held from May 27 to May 29 2014 in Ningbo, China. The technical program consisted of 8 international keynote speakers, oral presentations, and a poster session. The conference also included an industrial exhibition where more than 50 companies displayed in their booths their most recent advanced products and services. The present issue of IOP Conference Series: Materials Science and Engineering (MSE) records the proceedings of PCM 2014 and contains 37 specially selected manuscripts submitted to PCM2014 conference. The electronic submission and handling of manuscripts via the conference website, including the selection of reviewers and evaluation of manuscripts, were identical to the procedures applied to manuscripts submitted as regular contributions for publication. The organization of this conference and the preparation of proceedings volumes would have been impossible without the tremendous efforts and dedication of many individuals, especially from Ms. Yin Pan, who oversaw the organization of the conference and the program; and a large team of reviewers with their timely submission of quality reports. We express our sincere thanks to all authors and presenters for their contributions. We also thank very much our sponsors for their generous support. The 2015 Global Conference on Polymer and Composite Materials (PCM2015) will be held in Beijing, China on May 16-18, 2015. Beijing, the capital of the People's Republic of China and one of the most populous cities in the world, will welcome to all participants for a renewed and vibrant conference. Prof. Dr. Esteban Broitman Linköping University, Sweden Editor in Chief — PCM2014

  1. 2014 Global Conference on Polymer and Composite Materials (PCM 2014)

    International Nuclear Information System (INIS)

    2014-01-01

    The 2014 Global Conference on Polymer and Composite Materials (PCM 2014) sponsored by Ningbo Adhesives and Products Industry Association, Shanghai Bonding Technology Association, Zhejiang Bonding Technology Association, Wuhan Bonding Technology Association, Hebei Bonding and Coatings Association and Polyurethane Industry Association was held from May 27 to May 29 2014 in Ningbo, China. The technical program consisted of 8 international keynote speakers, oral presentations, and a poster session. The conference also included an industrial exhibition where more than 50 companies displayed in their booths their most recent advanced products and services. The present issue of IOP Conference Series: Materials Science and Engineering (MSE) records the proceedings of PCM 2014 and contains 37 specially selected manuscripts submitted to PCM2014 conference. The electronic submission and handling of manuscripts via the conference website, including the selection of reviewers and evaluation of manuscripts, were identical to the procedures applied to manuscripts submitted as regular contributions for publication. The organization of this conference and the preparation of proceedings volumes would have been impossible without the tremendous efforts and dedication of many individuals, especially from Ms. Yin Pan, who oversaw the organization of the conference and the program; and a large team of reviewers with their timely submission of quality reports. We express our sincere thanks to all authors and presenters for their contributions. We also thank very much our sponsors for their generous support. The 2015 Global Conference on Polymer and Composite Materials (PCM2015) will be held in Beijing, China on May 16–18, 2015. Beijing, the capital of the People's Republic of China and one of the most populous cities in the world, will welcome to all participants for a renewed and vibrant conference. Prof. Dr. Esteban Broitman Linköping University, Sweden Editor in Chief — PCM

  2. Sleep Comfort Evaluation in Bedding that Utilized Phase Change Materials (PCM)

    OpenAIRE

    橋本, 一馬; 青井, 政貴; 吉田, 宏昭; 上條, 正義

    2015-01-01

    The purpose of this study is to reveal the bedding influence degree to quality of sleep. This bedding utilized Phase Change Materials (PCM). We carried out two experiments. Firstly, we experimentally confirmed thermal properties of the PCM. Secondly, we carried out overnight sleep experiment in hot and cold environment. We prepared the PCM bedding and normal bedding that is commercially-supplied. Consequently, the PCM had been the property of cold tactile sensation rather than the normal bedd...

  3. Estudio de materiales con cambio de fase (PCM y análisis SEM de Micro PCM

    Directory of Open Access Journals (Sweden)

    David Juarez Varón

    2012-11-01

    Full Text Available This study analyzes the different classifications of phase change materials available at industrial level, in order to identify those that are potentially viable for addition with thermoplastic materials. Also, select a potentially interesting PCM and perform microscopic analysis of it.

  4. Building roof with conical holes containing PCM to reduce the cooling load: Numerical study

    International Nuclear Information System (INIS)

    Alawadhi, Esam M.; Alqallaf, Hashem J.

    2011-01-01

    Highlights: → We investigated a roof structure with cone frustum holes containing PCM. → Different types of PCM and geometries of the PCM are presented. → The results indicate that the heat flux at the indoor space is reduced by 39%. - Abstract: The thermal effectiveness of a building's roof with phase change material (PCM) is presented in this paper. The considered model consists of a concrete slab with vertical cone frustum holes filled with PCM. The objective of incorporating the PCM into the roof structure is to utilize its high latent heat of fusion to reduce the heat gain during the energy demanded peak hours, by absorbing the incoming energy through the melting process in the roof before it reaches the indoor space. The thermal effectiveness of the proposed roof-PCM system is determined by comparing the heat flux at the indoor surface to a roof without the PCM during typical working hours. A parametric study is conducted to assess the effects of the cone frustum geometry, and the kind of PCM used. The n-Eicosane shows the best performance among the examined PCMs, and the conical geometry of the PCM container is the best in term of thermal effectiveness. The results indicate that the heat flux at the indoor surface of the roof can be reduced up to 39% for a certain type of PCM and geometry of PCM cone frustum holes.

  5. PCM-enhanced lime plasters for vernacular and contemporary architecture

    Science.gov (United States)

    Theodoridou, Magdalini; Kyriakou, Loucas; Ioannou, Ioannis

    2016-04-01

    In 1997, the European Union (EU) pledged to reduce the amount of greenhouse gas emissions by 20% below the levels of 1990 by the end of 2020. In recent years it has become evident that, in order to reach that goal, EU Member States must take measures to encourage sustainability in the building industry, which is a major energy consumer. Such measures should involve the use of innovative, environmentally friendly materials and methods in new constructions, as well as the renovation of existing properties by upgrading their current state of energy efficiency. Phase Change Materials (PCMs) have the ability to absorb and release thermal energy, in the form of latent heat, during the melting or solidifying processes respectively. Thus, they may be used as additives in the production of thermally efficient composite building materials. A PCM-enhanced plaster is a heat storage medium combining an appropriate PCM with a cementitious or non-cementitious matrix to produce a low-cost thermal storage material with structural and thermostatic properties. Although innovative technologies, such as PCMs, have certainly contributed to the boost in the evolution of the building materials industry in recent years, a significant proportion of these technologies and practices have not yet been fully exploited in materials based on traditional principles. This paper focuses on the design and production of novel cementless PCM-enhanced lime plasters, in line with the traditional production technology of lime composites. The new plasters are produced using either hydrated or natural hydraulic lime binder, crushed calcarenite sand (0-2 mm) and commercial microencapsulated PCM in powder form (5% w/w of solids). Results from comparative tests between reference mixtures and mixtures with the addition of PCM, carried out 28, 56 and 90 days after laboratory production, prove the potential of PCMs in enhancing the thermal performance of traditional lime-based composites. The modified composites

  6. Accidents - Chernobyl accident; Accidents - accident de Tchernobyl

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    This file is devoted to the Chernobyl accident. It is divided in four parts. The first part concerns the accident itself and its technical management. The second part is relative to the radiation doses and the different contaminations. The third part reports the sanitary effects, the determinists ones and the stochastic ones. The fourth and last part relates the consequences for the other European countries with the case of France. Through the different parts a point is tackled with the measures taken after the accident by the other countries to manage an accident, the cooperation between the different countries and the groups of research and studies about the reactors safety, and also with the international medical cooperation, specially for the children, everything in relation with the Chernobyl accident. (N.C.)

  7. Thermal performance of a PCM thermal storage unit

    Energy Technology Data Exchange (ETDEWEB)

    Liu Ming; Bruno, Frank; Saman, Wasim [Sustainable Energy Centre, Inst. for Sustainable Systems and Technologies, Univ. of South Australia, Mawson Lakes, Adelaide (Australia)

    2008-07-01

    The thermal performance of a PCM thermal storage unit (TSU) is studied numerically and experimentally. The TSU under analysis consists of several flat slabs of phase change material (PCM) with melting temperature of -26.7 C. Liquid heat transfer fluid (HTF) passes between the slabs to charge and discharge the storage unit. A one dimensional mathematical model was employed to analyze the transient thermal behavior of the storage unit during the melting and freezing processes. The model takes into consideration the temperature variations in the wall along the flow direction of the HTF. The paper compares the experimental and numerical simulation results in terms of HTF outlet temperatures during the melting period. (orig.)

  8. Energy Optimized Configuration of Concrete Element with PCM

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew

    fulfillment of the new requirements regarding the new energy frames. The concept presented and developed in the thesis focuses on the energy optimization and potential of the new product that could utilize the high thermal energy storage (TES) and thermally activated building system (TABS). The work...... investigates the potential of combining the microencapsulated phase change material (PCM) in the hollow core concrete deck element in order to increase the dynamic heat storage capacity of the internal envelope of the multi-storey buildings. Moreover, the study investigates the cooling capacity and performance...... of the concrete deck with PCM and integrated TABS and highlights limitations and challenges of the new technology. Results from the full-scale investigation of dynamic heat storage capacity of decks indicated that there is no substantial difference between decks with extended heat transfer surface and one...

  9. Energy Optimized Configuration of Concrete Element with PCM

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew

    fulfillment of the new requirements regarding the new energy frames. The concept presented and developed in the thesis focuses on the energy optimization and potential of the new product that could utilize the high thermal energy storage (TES) and thermally activated building system (TABS). The work...... investigates the potential of combining the microencapsulated phase change material (PCM) in the hollow core concrete deck element in order to increase the dynamic heat storage capacity of the internal envelope of the multi-storey buildings. Moreover, the study investigates the cooling capacity and performance...... of the concrete deck with PCM and integrated TABS and highlights limitations and challenges of the new technology. The presented work utilizes numerical methods to study the dynamic performance of the new product developed. Consequently, the experimental set-ups and methodologies are developed firstly...

  10. Corrosion of metal and polymer containers for use in PCM cold storage

    International Nuclear Information System (INIS)

    Oró, Eduard; Miró, Laia; Barreneche, Camila; Martorell, Ingrid; Farid, Mohammed M.; Cabeza, Luisa F.

    2013-01-01

    Highlights: ► The corrosion of materials in contact with some low temperature PCM is studied. ► Copper and carbon steel must be avoided when using the PCM tested. ► Aluminium is not recommended with the tested PCM. ► Stainless steel 316 is recommended when in contact with the tested PCM. ► PP, PS, PET, and HDPE are not affected by a process of degradation by the tested PCM. - Abstract: Transport and storage of low temperature sensitive products is an issue worldwide due to changes of the lifestyle and population increase. In the recent years, thermal energy storage (TES) using phase change materials (PCMs) is being highly studied and developed for cold storage applications. Furthermore, the PCM are normally encapsulated in containers and added in the available systems, usually in food processes. Therefore safety constraints as the compatibility of the PCM with other materials have to take into account. Hence the main goal of the paper is to study the corrosion effect of different metals and polymer materials in contact with some PCM used in low temperature applications. Results show that copper and carbon steel must be avoided as PCM containers, and aluminium is not recommended; stainless steel 316 is recommended when in contact with the tested PCM. Moreover, PP, PS, PET, and HDPE are not affected by a process of degradation and are also compatible with the PCM studied

  11. Numerical analysis for the optimal location of a thin PCM layer in frame walls

    International Nuclear Information System (INIS)

    Jin, Xing; Medina, Mario A.; Zhang, Xiaosong

    2016-01-01

    Highlights: • The optimal PCM location was estimated by a mathematical model. • The optimal PCM location was affected by the properties of PCM. • The optimal PCM location was affected by the environmental conditions. - Abstract: The thermal performance of building walls can be improved using phase change materials (PCMs). The objective of this study was to estimate the optimal location of a “thin” PCM layer to be incorporated into frame walls, parallel to the frame and insulation, for the purpose of increasing thermal mass and reducing peak heat fluxes through the wall. Based on a mathematical model built in this paper, it was found that an optimal location of this “thin” PCM layer can be estimated, and it was affected by the thermal properties of PCM and the environmental conditions. The optimal locations for the PCM layer were found to be closer to the exterior surface of the wall when the thickness of PCM layer, the heat of fusion of PCM, and the PCM melting temperature were increased, while the optimal location was closer to the interior surface of the wall when the interior surface temperature of the wall was increased.

  12. Preparing side charging of PCM storage: theoretical and experimental investigation

    International Nuclear Information System (INIS)

    Tesfay, A H; Nydal, O J; Hagos, F Y; Yohannes, K G; Kahsay, M B

    2015-01-01

    In Ethiopia, there is an abundant source of solar energy that is estimated to 5.3 kWh/m 2 /day. However, more than 90% of the society uses biomass as a main source of energy for cooking due to lack of technologies to convert this energy. Replacing these cooking activities by using renewable energy resources decreases pollution and reduces deforestation significantly. Using the solar energy in day time has no problem. For night time however, the system needs some kind of back-up system to make the daytime solar energy available. This back-up should have high-density energy storage and constant working temperature to perform a specific application. Latent heat storage using phase change materials (PCM) is one way of storing thermal energy. In the current study, a latent heat storage that uses a PCM material is used to store the solar energy aimed at utilizing solar energy for cooking Injera, main staple bread in Ethiopia. The PCM is a mixture of 60% NaNO 3 and 40% KNO 3 that are known as solar salts. The storage has a welded parallel aluminum fins with a gap of 40 mm in between to enhance the thermal conductivity during the charging-discharging process of the storage. The fins are extruded outside of the storage container to enable a side charging technique for the PCM. A prototype was developed with a solar salt of 17.5 kg and is tested for charging-discharging. The numerical simulation done on ANSYS and experimental results show an agreement and the system registered a 41.6% efficiency. (paper)

  13. A Study on the Preparation of Spherical PCM Particle and Its Encapsulation

    Energy Technology Data Exchange (ETDEWEB)

    Kim, J.K. [Dept. of Chemical Engineering, Konyang University (Korea); Yoon, W.S.; Jung, K.T.; Shul, Y.G. [Dept. of Chemical Engineering, Yonsei University, Seoul (Korea); Joo, H.K.; Jeon, M.S.; Lee, T.K. [Korea Institute of Energy Research, Taejon (Korea)

    1999-04-01

    Spherical shape of phase change materials(PCM) were prepared by using sodium acetate trihydrate as a latent heat storage medium and then encapsulated with PMMA and wax. Gelatin was used as an effective thickener to prevent undesirable phase separation and sodium pyrophosphate decahydrate was used as nucleator to decrease the degree of supercooling in the thickened PCM. The optimal composition of PCM was 2 wt% thickener and 2wt% nucleator. Spherical shape of PCM particles of 3-3.5 mm in diameter were continuously manufactured varing the effluent velocity of molten PCM from 1.3 to 1.8 ml/min. Tertiary coatings of PMMA-wax-PMMA onto the PCM particles obtained were 0.03 mm, 0.25 mm, and 0.4 mm. Freezing-thaw cycle test of the coated PCM particle was done using dodecane as heat transfer medium by the experimental apparatus and DSC. 15 refs., 11 figs., 5 tabs.

  14. Numerical analysis on thermal performance of roof contained PCM of a single residential building

    International Nuclear Information System (INIS)

    Li, Dong; Zheng, Yumeng; Liu, Changyu; Wu, Guozhong

    2015-01-01

    Highlights: • Thermal performance of different roofs in cold area of China are investigated. • Effects of five different conditions on thermal performance of roofs are analyzed. • Delay time of temperatures peak in PCM roofs are beyond 3 h than common roof. - Abstract: The phase change material (PCM) applied in the roof can decrease the building energy consumption and improve the thermal comfort by enhancing the thermal energy storage capacity of building envelope. In the present work, the thermal performance of different kinds of roofs with and without PCM in Northeast and cold area of China, i.e. common roof and PCM roofs, have been investigated numerically. This study also explored the influencing factors of thermal behavior of the roofs, such as solar radiation intensity, transition temperature and latent heat of PCM, roof slope, PCM layer thickness, and absorption coefficients of external roof surface. The results show that the PCM roofs effect on the temperature delay in the room is very strong and the delay time of temperatures peak of base layer in PCM roofs are beyond 3 h than common roof. The effect of transition temperature and latent heat of PCM on the thermal performance of roofs is relatively weak, compared with the roof slope, PCM layer thickness and absorption coefficients of external roof surface

  15. Combined experimental and numerical evaluation of a prototype nano-PCM enhanced wallboard

    International Nuclear Information System (INIS)

    Biswas, Kaushik; Lu, Jue; Soroushian, Parviz; Shrestha, Som

    2014-01-01

    Highlights: • Field-testing of a nano-PCM wallboard under varying weather conditions. • Numerical model validation and annual simulations of PCM wallboard performance. • Reduced cooling electricity consumption results from PCM wallboard. • PCM wallboard reduces peak cooling loads with implications on power plant capacity. • PCM performance was sensitive to building temperature set point for cooling. - Abstract: In the United States, forty-eight (48) percent of the residential end-use energy consumption is spent on space heating and air conditioning. Reducing envelope-generated heating and cooling loads through application of phase change materials (PCMs) in building envelopes can enhance the energy efficiency of buildings and reduce energy consumption. Experimental testing and numerical modeling of PCM-enhanced envelope components are two important aspects of the evaluation of their energy benefits. An innovative phase change material (nano-PCM) was developed with PCM supported by expanded graphite (interconnected) nanosheets, which are highly conductive and allow enhanced thermal storage and energy distribution. The nano-PCM is shape-stable for convenient incorporation into lightweight building components. A wall with cellulose cavity insulation and a prototype PCM-enhanced interior wallboard was built and tested in a natural exposure test (NET) facility in a hot-humid climate location. The test wall contained the PCM wallboard and a regular gypsum wallboard, for a side-by-side annual comparison study. Further, numerical modeling of the wall containing the nano-PCM wallboard was performed to determine its actual impact on wall-generated heating and cooling loads. The model was first validated using experimental data, and then used for annual simulations using typical meteorological year (TMY3) weather data. This article presents the measured performance and numerical analysis evaluating the energy-saving potential of the nano-PCM-enhanced wallboard

  16. Structural-functional integrated concrete with macro-encapsulated inorganic PCM

    Science.gov (United States)

    Mohseni, Ehsan; Tang, Waiching; Wang, Zhiyu

    2017-09-01

    Over the last few years the application of thermal energy storage system incorporating phase change materials (PCMs) to foster productivity and efficiency of buildings energy has grown rapidly. In this study, a structural-functional integrated concrete was developed using macro-encapsulated PCM-lightweight aggregate (LWA) as partial replacement (25 and 50% by volume) of coarse aggregate in control concrete. The PCM-LWA was prepared by incorporation of an inorganic PCM into porous LWAs through vacuum impregnation. The mechanical and thermal performance of PCM-LWA concrete were studied. The test results revealed that though the compressive strength of concrete with PCM-LWA was lower than the control concrete, but ranged from 22.02 MPa to 42.88 MPa which above the minimum strength requirement for structural application. The thermal performance test indicated that macro-encapsulated PCM-LWA has underwent the phase change transition reducing the indoor temperature.

  17. Centrioles regulate centrosome size by controlling the rate of Cnn incorporation into the PCM.

    Science.gov (United States)

    Conduit, Paul T; Brunk, Kathrin; Dobbelaere, Jeroen; Dix, Carly I; Lucas, Eliana P; Raff, Jordan W

    2010-12-21

    centrosomes are major microtubule organizing centers in animal cells, and they comprise a pair of centrioles surrounded by an amorphous pericentriolar material (PCM). Centrosome size is tightly regulated during the cell cycle, and it has recently been shown that the two centrosomes in certain stem cells are often asymmetric in size. There is compelling evidence that centrioles influence centrosome size, but how centrosome size is set remains mysterious. we show that the conserved Drosophila PCM protein Cnn exhibits an unusual dynamic behavior, because Cnn molecules only incorporate into the PCM closest to the centrioles and then spread outward through the rest of the PCM. Cnn incorporation into the PCM is driven by an interaction with the conserved centriolar proteins Asl (Cep152 in humans) and DSpd-2 (Cep192 in humans). The rate of Cnn incorporation into the PCM is tightly regulated during the cell cycle, and this rate influences the amount of Cnn in the PCM, which in turn is an important determinant of overall centrosome size. Intriguingly, daughter centrioles in syncytial embryos only start to incorporate Cnn as they disengage from their mothers; this generates a centrosome size asymmetry, with mother centrioles always initially organizing more Cnn than their daughters. centrioles can control the amount of PCM they organize by regulating the rate of Cnn incorporation into the PCM. This mechanism can explain how centrosome size is regulated during the cell cycle and also allows mother and daughter centrioles to set centrosome size independently of one another.

  18. System Level Analysis of a Water PCM HX Integrated into Orion's Thermal Control System

    Science.gov (United States)

    Navarro, Moses; Hansen, Scott; Seth, Rubik; Ungar, Eugene

    2015-01-01

    In a cyclical heat load environment such as low Lunar orbit, a spacecraft's radiators are not sized to reject the full heat load requirement. Traditionally, a supplemental heat rejection device (SHReD) such as an evaporator or sublimator is used to act as a "topper" to meet the additional heat rejection demands. Utilizing a Phase Change Material (PCM) heat exchanger (HX) as a SHReD provides an attractive alternative to evaporators and sublimators as PCM HXs do not use a consumable, thereby leading to reduced launch mass and volume requirements. In continued pursuit of water PCM HX development an Orion system level analysis was performed using Thermal Desktop for a water PCM HX integrated into Orion's thermal control system in a 100km Lunar orbit. The study verified of the thermal model by using a wax PCM and analyzed 1) placing the PCM on the Internal Thermal Control System (ITCS) versus the External Thermal Control System (ETCS) 2) use of 30/70 PGW verses 50/50 PGW and 3) increasing the radiator area in order to reduce PCM freeze times. The analysis showed that for the assumed operating and boundary conditions utilizing a water PCM HX on Orion is not a viable option for any case. Additionally, it was found that the radiator area would have to be increased by at least 40% in order to support a viable water-based PCM HX.

  19. Transient cooling of electronics using phase change material (PCM)-based heat sinks

    International Nuclear Information System (INIS)

    Kandasamy, Ravi; Wang Xiangqi; Mujumdar, Arun S.

    2008-01-01

    Use of a phase change material (PCM)-based heat sink in transient thermal management of plastic quad flat package (QFP) electronic devices was investigated experimentally and numerically. Results show that increased power inputs enhance the melting rate as well as the thermal performance of the PCM-based heat sinks until the PCM is fully melted. A three-dimensional computational fluid dynamics model was proposed to simulate the problem and demonstrated good agreement with experimental data. Results indicate the potential for PCM-based heat sinks for use in intermittent-use devices

  20. Power-Cooling-Mismatch Test Series Test PCM-7. Experiment operating specifications

    International Nuclear Information System (INIS)

    Sparks, D.T.; Smith, R.H.; Stanley, C.J.

    1979-02-01

    The experiment operating specifications for the Power-Cooling-Mismatch (PCM) Test PCM-7 to be conducted in the Power Burst Facility are described. The PCM Test Series was designed on the basis of a parametric evaluation of fuel behavior response with cladding temperature, rod internal pressure, time in film boiling, and test rod power being the variable parameters. The test matrix, defined in the PCM Experiment Requirements Document (ERD), encompasses a wide range of situations extending from pre-CHF (critical heat flux) PCMs to long duration operation in stable film boiling leading to rod failure

  1. Experimental comparison between different configurations of PCM based heat sinks for cooling electronic components

    International Nuclear Information System (INIS)

    Gharbi, Salma; Harmand, Souad; Jabrallah, Sadok Ben

    2015-01-01

    The thermal control of electronic components is aimed at ensuring their use in a temperature range compatible with their performances. This paper presents an experimental study of the behavior of phase change materials (PCMs) as the cooling system for electronic devices. Four configurations are used to control the increase in the system temperature: pure PCM, PCM in a silicone matrix, PCM in a graphite matrix and pure PCM in a system of fins. Thermo-physical properties of different PCMs are determined and found to be desirable for application in this study. Solid liquid interface visualization and temperature evolution are employed to understand the mechanism of heat transfer during the different stages. Results indicated that the inclusion of PCM can lower component increase temperature and extends twice the critical time of the heat sink. The use of Graphite matrix filled by PCM showed more improvement on system thermal performance than silicon matrix. Also, for the same fraction of copper, it was found that incorporating long copper fins with suitable spacing into PCM, can enhance heat distribution into PCM leading to longer remain component temperature below the critical limit. This work therefore shows that the combination of PCM and long, well-spaced fins presents an effective means for thermal control of electronic devices. - Highlights: • Study on thermal performance of different PCM based heat sink in electronic cooling. • Examination of heat transfer mechanism into heat sink for different conditions. • Graphite matrix shows more efficiency than silicon. • Inclusion PCM can reduce temperature increasing. • Heat sink with longer well spaced fins can extend longer the critical time

  2. Accidents - Chernobyl accident

    International Nuclear Information System (INIS)

    2004-01-01

    This file is devoted to the Chernobyl accident. It is divided in four parts. The first part concerns the accident itself and its technical management. The second part is relative to the radiation doses and the different contaminations. The third part reports the sanitary effects, the determinists ones and the stochastic ones. The fourth and last part relates the consequences for the other European countries with the case of France. Through the different parts a point is tackled with the measures taken after the accident by the other countries to manage an accident, the cooperation between the different countries and the groups of research and studies about the reactors safety, and also with the international medical cooperation, specially for the children, everything in relation with the Chernobyl accident. (N.C.)

  3. Macro-Encapsulated PCM Cylinder Module Based on Paraffin and Float Stones

    Directory of Open Access Journals (Sweden)

    Kailiang Huang

    2016-05-01

    Full Text Available Organic phase change material (PCM with macro-encapsulation is attractive in energy storage applications as it has relatively low cost. This study focuses on using PET plastic pipes to encapsulate paraffin and using low-cost float stones to increase the thermal conductivity of PCM modules as they have a special structure of high porosity. Float stones were immersed in the liquid PCM and an ultrasonic welding method used to prevent leakage of the PET plastic pipes. Scanning electron microscopy (SEM was used to discover the appearance of the composite PCM. The thermal performance of the PCM cylinder module was analyzed through experimental tests of a constant-temperature water bath and numerical simulations. The result indicates that this PCM Ccylinder module is superior in thermal energy storage compared with the reference module even though fewer PCM was contained and the latent heat loss is considerable. The pipe diameter is an important parameter when using this kind of PCM cylinder module in water tanks.

  4. System Level Analysis of a Water PCM HX Integrated Into Orion's Thermal Control System Abstract

    Science.gov (United States)

    Navarro, Moses; Hansen, Scott; Ungar, Eugene; Sheth, Rubik

    2015-01-01

    In a cyclical heat load environment such as low Lunar orbit, a spacecraft's radiators are not sized to reject the full heat load requirement. Traditionally, a supplemental heat rejection device (SHReD) such as an evaporator or sublimator is used to act as a "topper" to meet the additional heat rejection demands. Utilizing a Phase Change Material (PCM) heat exchanger (HX) as a SHReD provides an attractive alternative to evaporators and sublimators as PCM HXs do not use a consumable, thereby leading to reduced launch mass and volume requirements. In continued pursuit of water PCM HX development an Orion system level analysis was performed using Thermal Desktop for a water PCM HX integrated into Orion's thermal control system and in a 100km Lunar orbit. The study analyzed 1) placing the PCM on the Internal Thermal Control System (ITCS) versus the External Thermal Control System (ETCS) 2) use of 30/70 PGW verses 50/50 PGW and 3) increasing the radiator area in order to reduce PCM freeze times. The analysis showed that for the assumed operating and boundary conditions utilizing a water PCM HX on Orion is not a viable option. Additionally, it was found that the radiator area would have to be increased over 20% in order to have a viable water-based PCM HX.

  5. Experimental and Numerical Research of the Thermal Properties of a PCM Window Panel

    Directory of Open Access Journals (Sweden)

    Martin Koláček

    2017-07-01

    Full Text Available This paper reports the experimental and simulation analysis of a window system incorporating Phase Change Materials (PCMs. In this study, the latent heat storage material is exploited to increase the thermal mass of the building component. A PCM-filled window can increase the possibilities of storage energy from solar radiation and reduce the heating cooling demand. The presented measurements were performed on a specific window panel that integrates a PCM. The PCM window panel consists of four panes of safety glass with three gaps, of which the first one contains a prismatic glass, the second a krypton gas, and the last one a PCM. New PCM window panel technology uses the placement of the PCM in the whole space of the window cavity. This technology improves the thermal performance and storage mass of the window panel. The results show the incongruent melting of salt hydrates and the high thermal inertia of the PCM window panel. The simulation data showed that the PCM window panel and the double glazing panel markedly reduced the peak temperature on the interior surface, reduced the air temperature inside the room, and also considerably improved the thermal mass of the building. This means that the heat energy entering the building through the panel is reduced by 66% in the summer cycle.

  6. Postulated accidents

    International Nuclear Information System (INIS)

    Ullrich, W.

    1980-01-01

    This lecture on 'Postulated Accidents' is the first of a series of lectures on the dynamic and transient behaviour of nuclear power plants, especially pressurized water reactors. The main points covered will be: Reactivity Accidents, Transients (Intact Loop) and Loss of Cooland Accidents (LOCA) including small leak. This lecture will discuss the accident analysis in general, the definition of the various operational phases, the accident classification, and, as an example, an accident sequence analysis on the basis of 'Postulated Accidents'. (orig./RW)

  7. [Verification of bacteriological safety of PCM 40 air conditioner].

    Science.gov (United States)

    Dumas, J L; Ducel, G; Rouge, J C

    1991-01-01

    This study assessed the bacteriological safety of the bedside air conditioner PCM 40 (Howorth Airtech), used for prevention of intraoperative hypothermia, by blowing filtered warm air through a special mattress. The 3 microns bacterial filter of the device released 2,968 +/- 5,618 particles of diameter less than 3 microns per m3 of room air, containing 78,798 +/- 37,243 of such particles per m3. The amount of bacteries in the air pulsed from the mattress was 30 +/- 41 cfu/m3 vs 120 cfu/m3 in the ambient air and in the hot air supply tubing it reached 6 +/- 5 cfu/m3 vs 175 +/- 77 cfu/m3. It is concluded that bacteriological data do not contra-indicate the use of this air conditioner in the operating theater. The only limitations for use are the position (prone or lateral position) and type of surgery (neurosurgery).

  8. Compact seasonal PCM heat storage for solar heating systems

    DEFF Research Database (Denmark)

    Dannemand, Mark

    Space heating of buildings and preparation of domestic hot water accounts for a large part of the society’s energy consumption. Solar radiation is an abundant and renewable energy source which can be harvested by solar collectors and used to cover heating demands in the built environment....... The seasonal availability of solar energy does however not match with the heating demands in buildings which typically are large in winter periods when limited solar energy is available. Heat can be stored over a few days in water stores but continuous heat losses limits the storage periods. The possibility...... of storing heat from summer where solar energy is widely available to winter periods where the heating demands are large, allows for implementing more renewable energy in our energy system. The phase change material (PCM) sodium acetate trihydrate (SAT) melts at 58 °C. The melting process requires...

  9. Review of thermal energy storage technologies based on PCM application in buildings

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew; Heiselberg, Per; Zhang, Yinping

    2013-01-01

    Thermal energy storage systems (TES), using phase change material (PCM) in buildings, are widely investigated technologies and a fast developing research area. Therefore, there is a need for regular and consistent reviews of the published studies. This review is focused on PCM technologies...... is paid to discussion and identification of proper methods to correctly determine the thermal properties of PCM materials and their composites and as well procedures to determine their energy storage and saving potential. The purpose of the paper is to highlight promising technologies for PCM application...... developed to serve the building industry. Various PCM technologies tailored for building applications are studied with respect to technological potential to improve indoor environment, increase thermal inertia and decrease energy use for building operation. What is more, in this review special attention...

  10. PCM1 Depletion Inhibits Glioblastoma Cell Ciliogenesis and Increases Cell Death and Sensitivity to Temozolomide

    Directory of Open Access Journals (Sweden)

    Lan B. Hoang-Minh

    2016-10-01

    Full Text Available A better understanding of the molecules implicated in the growth and survival of glioblastoma (GBM cells and their response to temozolomide (TMZ, the standard-of-care chemotherapeutic agent, is necessary for the development of new therapies that would improve the outcome of current GBM treatments. In this study, we characterize the role of pericentriolar material 1 (PCM1, a component of centriolar satellites surrounding centrosomes, in GBM cell proliferation and sensitivity to genotoxic agents such as TMZ. We show that PCM1 is expressed around centrioles and ciliary basal bodies in patient GBM biopsies and derived cell lines and that its localization is dynamic throughout the cell cycle. To test whether PCM1 mediates GBM cell proliferation and/or response to TMZ, we used CRISPR/Cas9 genome editing to generate primary GBM cell lines depleted of PCM1. These PCM1-depleted cells displayed reduced AZI1 satellite protein localization and significantly decreased proliferation, which was attributable to increased apoptotic cell death. Furthermore, PCM1-depleted lines were more sensitive to TMZ toxicity than control lines. The increase in TMZ sensitivity may be partly due to the reduced ability of PCM1-depleted cells to form primary cilia, as depletion of KIF3A also ablated GBM cells' ciliogenesis and increased their sensitivity to TMZ while preserving PCM1 localization. In addition, the co-depletion of KIF3A and PCM1 did not have any additive effect on TMZ sensitivity. Together, our data suggest that PCM1 plays multiple roles in GBM pathogenesis and that associated pathways could be targeted to augment current or future anti-GBM therapies.

  11. Experimental and numerical studies of hybrid PCM embedded in plastering mortar for enhanced thermal behaviour of buildings

    International Nuclear Information System (INIS)

    Kheradmand, Mohammad; Azenha, Miguel; Aguiar, José L.B. de; Castro-Gomes, João

    2016-01-01

    This paper proposes a methodology for improvement of energy efficiency in buildings through the innovative simultaneous incorporation of three distinct phase change materials (here termed as hybrid PCM) in plastering mortars for façade walls. The thermal performance of a hybrid PCM mortar was experimentally evaluated by comparing the behaviour of a prototype test cell (including hybrid PCM plastering mortar) subjected to realistic daily temperature profiles, with the behaviour of a similar prototype test cell, in which no PCM was added. A numerical simulation model was employed (using ANSYS-FLUENT) to validate the capacity of simulating temperature evolution within the prototype containing hybrid PCM, as well as to understand the contribution of hybrid PCM to energy efficiency. Incorporation of hybrid PCM into plastering mortars was found to have the potential to significantly reduce heating/cooling temperature demands for maintaining the interior temperature within comfort levels when compared to normal mortars (without PCM), or even mortars comprising a single type of PCM. - Highlights: • New concept of incorporation of more than 1 type of PCM in plastering mortars (hybrid PCM). • Assessment of thermal performance of hybrid PCM plastering mortar. • Thermo-physical properties of plastering mortars modified with PCMs incorporation. • Experimental and numerical simulations of thermal behaviour on laboratory scale prototype.

  12. Analytical optimization of interior PCM for energy storage in a lightweight passive solar room

    International Nuclear Information System (INIS)

    Xiao Wei; Wang Xin; Zhang Yinping

    2009-01-01

    Lightweight envelopes are widely used in modern buildings but they lack sufficient thermal capacity for passive solar utilization. An attractive solution to increase the building thermal capacity is to incorporate phase change material (PCM) into the building envelope. In this paper, a simplified theoretical model is established to optimize an interior PCM for energy storage in a lightweight passive solar room. Analytical equations are presented to calculate the optimal phase change temperature and the total amount of latent heat capacity and to estimate the benefit of the interior PCM for energy storage. Further, as an example, the analytical optimization is applied to the interior PCM panels in a direct-gain room with realistic outdoor climatic conditions of Beijing. The analytical results agree well with the numerical results. The analytical results show that: (1) the optimal phase change temperature depends on the average indoor air temperature and the radiation absorbed by the PCM panels; (2) the interior PCM has little effect on average indoor air temperature; and (3) the amplitude of the indoor air temperature fluctuation depends on the product of surface heat transfer coefficient h in and area A of the PCM panels in a lightweight passive solar room.

  13. The management of plutonium (alpha) contaminated waste materials (PCM)

    International Nuclear Information System (INIS)

    Sills, R.J.

    1984-01-01

    This article reviews the management strategies for plutonium contaminated materials (PCM), the techniques which have been used and developed for their implementation and what can be expected for the immediate future. In general reference is made to the situation in the U.K., but where appropriate the International context is noted. In the context of the article plutonium often occurs with other alpha-active materials and the two terms are used virtually synonymously. The technology which is described, and which is the result of substantial research and development programmes, has largely been developed with the objective of recovering the majority of plutonium prior to ultimate disposal of the waste. There is no doubt that this removal to low levels of contamination is technically feasible; indeed there are a number of methods to choose from each with its own advantages and disadvantages. The emphasis has shifted recently from the development and demonstration of technology for waste handling, treatment and disposal (although these are very important), to the assessment of the effects--social, technological and economic--of the various options available for dealing with the waste. The process is thus, one of achieving the lowest overall 'cost' to society; where 'cost' is in the broadest sense of effect on society and not in merely strict financial terms

  14. PCM-air heat exchangers for free-cooling applications in buildings: Experimental results of two real-scale prototypes

    International Nuclear Information System (INIS)

    Lazaro, Ana; Dolado, Pablo; Marin, Jose M.; Zalba, Belen

    2009-01-01

    Latent heat storage using phase change materials (PCM) can be used for free-cooling. In this application low air temperature is used to solidify the PCM during the night and then during the next day, the inside air of a building can be cooled down by exchanging heat with PCM. Short times for charging and discharging the PCM are required. PCM have in general low thermal conductivity, therefore the heat exchanger design is very important to fulfil free-cooling requirements. This paper presents an experimental setup for testing PCM-air real-scale heat exchangers and the results for two real-scale prototypes. Results show that a heat exchanger using a PCM with lower thermal conductivity and lower total stored energy, but adequately designed, has higher cooling power and can be applied for free-cooling

  15. Accident management

    International Nuclear Information System (INIS)

    Lutz, R.J.; Monty, B.S.; Liparulo, N.J.; Desaedeleer, G.

    1989-01-01

    The foundation of the framework for a Severe Accident Management Program is the contained in the Probabilistic Safety Study (PSS) or the Individual Plant Evaluations (IPE) for a specific plant. The development of a Severe Accident Management Program at a plant is based on the use of the information, in conjunction with other applicable information. A Severe Accident Management Program must address both accident prevention and accident mitigation. The overall Severe Accident Management framework must address these two facets, as a living program in terms of gathering the evaluating information, the readiness to respond to an event. Significant international experience in the development of severe accident management programs exist which should provide some direction for the development of Severe Accident Management in the U.S. This paper reports that the two most important elements of a Severe Accident Management Program are the Emergency Consultation process and the standards for measuring the effectiveness of individual Severe Accident Management Programs at utilities

  16. PCM/wood composite to store thermal energy in passive building envelopes

    Science.gov (United States)

    Barreneche, C.; Vecstaudza, J.; Bajare, D.; Fernandez, A. I.

    2017-10-01

    The development of new materials to store thermal energy in a passive building system is a must to improve the thermal efficiency by thermal-regulating the indoor temperatures. This fact will deal with the reduction of the gap between energy supply and energy demand to achieve thermal comfort in building indoors. The aim of this work was to test properties of novel PCM/wood composite materials developed at Riga Technical University. Impregnation of PCM (phase change material) in wood increases its thermal mass and regulates temperature fluctuations during day and night. The PCM used are paraffin waxes (RT-21 and RT-27 from Rubitherm) and the wood used was black alder, the most common wood in Latvia. The PCM distribution inside wood sample has been studied as well as its thermophysical, mechanical and fire reaction properties. Developed composite materials are promising in the field of energy saving in buildings.

  17. The prioritization and categorization method (PCM) process evaluation at Ericsson : a case study

    NARCIS (Netherlands)

    Ohlsson, Jens; Han, Shengnan; Bouwman, W.A.G.A.

    2017-01-01

    Purpose: The purpose of this paper is to demonstrate and evaluate the prioritization and categorization method (PCM), which facilitates the active participation of process stakeholders (managers, owners, customers) in process assessments. Stakeholders evaluate processes in terms of effectiveness,

  18. A New Method to Determine Thermal Properties of the Mixture of PCM and Concrete

    DEFF Research Database (Denmark)

    R., Cheng; Pomianowski, Michal Zbigniew; Heiselberg, Per

    on the inverse problem was proposed to deal with the measurements of thermal conductivity and specific heat of PCM-concretes during the phase change process. This method transforms the determination process to an optimization problem, which regarded the difference between the measured and calculated heat flux......Integration of phase change materials in building envelopes is a technology that with high potential to decrease the building energy consumption and improve indoor thermal comfort. Accurate measurement of thermal physical properties of PCM-concretes is very important for simulation and evaluation...... of its energy saving performance. However, there isn’t an effective way to measure thermal physical properties of PCM-concretes accurately. The shortcomings of using traditional testing methods to measure thermal physical properties of PCM-concretes were firstly analyzed. Then a new method based...

  19. Unavoidable Accident

    OpenAIRE

    Grady, Mark F.

    2009-01-01

    In negligence law, "unavoidable accident" is the risk that remains when an actor has used due care. The counterpart of unavoidable accident is "negligent harm." Negligence law makes parties immune for unavoidable accident even when they have used less than due care. Courts have developed a number of methods by which they "sort" accidents to unavoidable accident or to negligent harm, holding parties liable only for the latter. These sorting techniques are interesting in their own right and als...

  20. Innovative PCM-desiccant packet to provide dry microclimate and improve performance of cooling vest in hot environment

    International Nuclear Information System (INIS)

    Itani, Mariam; Ghaddar, Nesreen; Ghali, Kamel

    2017-01-01

    Highlights: • A PCM and desiccant packet is proposed for use in personal cooling vest to keep dry air next to skin. • A PCM-Desiccant model for clothed heated wet cylinder is developed and validated experimentally. • The microclimate air temperature was 0.6 °C higher in PCM-Desiccant case compared to PCM-only case. • Microclimate humidity content decreased due to desiccant from 21.23 to 19.74 g/kg dry air. • PCM melted fraction increased due to desiccant from 0.24 to 0.5. - Abstract: A novel combination of phase change material (PCM) and a solid desiccant layer is proposed for the aim of maintaining dry cool microclimate air adjacent to wet warm skin and hence improve PCM performance in cooling vests used in hot humid environment. A fabric-PCM-Desiccant model is developed to predict the temperature and moisture content of the microclimate air layer in the presence of a PCM-Desiccant packet. The developed model is validated through experiments conducted on a wet clothed heated cylinder for the two cases of using (i) a PCM only packet and (ii) a PCM-Desiccant packet. Microclimate air temperatures and humidity content as well as PCM and desiccant temperatures were measured experimentally and were compared with predicted values by the fabric-PCM-Desiccant model. Good agreement was attained with a maximum relative error of 7% in measured temperatures. A decrease is observed in the humidity content of the microclimate air in the presence of the solid desiccant from 21.23 g/kg dry air to 19.74 g/kg dry air and an increase in the melted fraction of the PCM at the end of the experiment from 0.24 to 0.5.

  1. Energy and economic analysis of a building air-conditioner with a phase change material (PCM)

    International Nuclear Information System (INIS)

    Chaiyat, Nattaporn

    2015-01-01

    Highlights: • Phase change material of Rubitherm20 was applied with the air-conditioner under the climate of Thailand. • PCM was used to reduce cooling load and electrical power of the air-conditioner. • Mathematical model of the packed ball bed of PCM was presented to predict the thermal performance. - Abstract: In this study, a concept of using phase change material (PCM) for improving cooling efficiency of an air-conditioner had been presented under Thailand climate. Rubitherm20 (RT-20) was selected to evaluate the thermal performance by reducing the air temperature entering the evaporating coil. The model of PCM celluloid balls had been performed with the air-conditioner. For the experiment, 2 TR of R-134a air-conditioner was chosen to test a pack bed of PCM balls with thickness 40 cm. The pressure drops of the air flowing through the bed were considered with and without a set of by-pass tubes along the height of the storage bed. The mathematical model of the air-conditioner with the PCM storage was developed and verified with the testing results. From the study results, it could be seen that pressure drops of the bed with and without bypass tubes were nearly the same results. Thus, PCM ball pack bed using RT-20 without bypass tubes was used to improve the cooling efficiency of the air-conditioner. The experimental result of the modified unit was compared and verified with the mathematical model, which agreed quite well with the simulation result. Finally, the model was used to analyze the economic result, which found that the electrical consumption of the modified air-conditioner could be decreased around 3.09 kW h/d. The saving cost from the PCM bed could be 9.10% of 170.03 USD/y and the payback period was around 4.15 y

  2. Study on the optimum PCM melting temperature for energy savings in residential buildings worldwide

    Science.gov (United States)

    Saffari, M.; de Gracia, A.; Fernández, C.; Zsembinszki, G.; Cabeza, L. F.

    2017-10-01

    To maintain comfort conditions in residential buildings along a full year period, the use of active systems is generally required to either supply heating or cooling. The heating and cooling demands strongly depend on the climatic conditions, type of building and occupants’ behaviour. The overall annual energy consumption of the building can be reduced by the use of renewable energy sources and/or passive systems. The use of phase change materials (PCM) as passive systems in buildings enhances the thermal mass of the envelope, and reduces the indoor temperature fluctuations. As a consequence, the overall energy consumption of the building is generally lower as compared to the case when no PCM systems are used. The selection of the PCM melting temperature is a key issue to reduce the energy consumption of the buildings. The main focus of this study is to determine the optimum PCM melting temperature for passive heating and cooling according to different weather conditions. To achieve that, numerical simulations were carried out using EnergyPlus v8.4 coupled with GenOpt® v3.1.1 (a generic optimization software). A multi-family residential apartment was selected from ASHRAE Standard 90.1- 2013 prototype building model, and different climate conditions were considered to determine the optimum melting temperature (in the range from 20ºC to 26ºC) of the PCM contained in gypsum panels. The results confirm that the optimum melting temperature of the PCM strongly depends on the climatic conditions. In general, in cooling dominant climates the optimum PCM temperature is around 26ºC, while in heating dominant climates it is around 20ºC. Furthermore, the results show that an adequate selection of the PCM as passive system in building envelope can provide important energy savings for both heating dominant and cooling dominant regions.

  3. A numerical study of external building walls containing phase change materials (PCM)

    International Nuclear Information System (INIS)

    Izquierdo-Barrientos, M.A.; Belmonte, J.F.; Rodríguez-Sánchez, D.; Molina, A.E.; Almendros-Ibáñez, J.A.

    2012-01-01

    Phase Change Materials (PCMs) have been receiving increased attention, due to their capacity to store large amounts of thermal energy in narrow temperature ranges. This property makes them ideal for passive heat storage in the envelopes of buildings. To study the influence of PCMs in external building walls, a one-dimensional transient heat transfer model has been developed and solved numerically using a finite difference technique. Different external building wall configurations were analyzed for a typical building wall by varying the location of the PCM layer, the orientation of the wall, the ambient conditions and the phase transition temperature of the PCM. The integration of a PCM layer into a building wall diminished the amplitude of the instantaneous heat flux through the wall when the melting temperature of the PCM was properly selected according to the season and wall orientation. Conversely, the results of the work show that there is no significant reduction in the total heat lost during winter regardless of the wall orientation or PCM transition temperature. Higher differences were observed in the heat gained during the summer period, due to the elevated solar radiation fluxes. The high thermal inertia of the wall implies that the inclusion of a PCM layer increases the thermal load during the day while decreasing the thermal load during the night. - Highlights: ► A comparative simulation of a building wall with and without PCMs has been conducted. ► PCM is selected according with the season, the wall orientation and the melting temperature. ► PCM in a building wall help to diminish the internal air temperature swings and to regulate the heat transfer.

  4. Experimental investigation of a novel indirect solar dryer implementing PCM as energy storage medium

    Energy Technology Data Exchange (ETDEWEB)

    Shalaby, S.M., E-mail: saleh_shalaby@yahoo.com; Bek, M. A.

    2014-07-01

    Highlights: • The performance of a novel indirect solar dryer is investigated experimentally. • PCM, paraffin wax, is used as energy storage medium. • The novel ISD is suitable for drying medical plants. • Ocimum and Thevetia are dried at their prescribed drying temperatures. • The novel design maintains the desired temperature for 7 consecutive h/day. - Abstract: A novel indirect solar dryer (ISD) design using phase change material (PCM) as energy storage medium was experimentally investigated. The system consists of two identical solar air heaters, drying compartment, PCM storage units and a blower. The ISD was tested under no load with and without PCM at a wide range of mass flow rates (0.0664–0.2182 kg/s). It is found that after using the PCM, the temperature of the drying air is higher than ambient temperature by 2.5–7.5 °C after sunset for five hours at least. In addition, the mass flow rates of 0.1204 and 0.0894 kg/s give the peak values of the drying temperature when the ISD is operated with and without PCM, respectively. The novel design successfully maintains the desired temperature for seven consecutive hours every day. This helps reaching the final moisture content of Ocimum Basilicum and Thevetia Neriifolia after 12 and 18 h, respectively.

  5. Exact solution of thermal energy storage system using PCM flat slabs configuration

    International Nuclear Information System (INIS)

    Bechiri, Mohammed; Mansouri, Kacem

    2013-01-01

    Highlights: • An exact solution of a latent heat storage unit (LHSU) consisting of several flat slabs was obtained. • The working fluid (HTF) circulating by forced convection between the slabs charges and discharges the storage unit. • The charging/discharging process is investigated for various HTF working conditions and different design parameters. - Abstract: An analytical investigation of thermal energy storage system (TESS) consisting of several flat slabs of phase change material (PCM) is presented. The working fluid (HTF) circulating on laminar forced convection between the slabs charges and discharges the storage unit. The melting and solidification of the PCM was treated as a radial one dimensional conduction problem. The forced convective heat transfer inside the channels is analyzed by solving the energy equation, which is coupled with the heat conduction equation in the PCM container. The comparison between the present exact solution with the numerical predictions and experimental data available in literature shows good agreement. The charging/discharging process is investigated in terms of liquid–solid interface position, liquid fraction, total heat transmitted to the PCM and thermal storage efficiency for various HTF working conditions and different design parameters such as PCM slab length, fluid passage gap and thickness of PCM duct container

  6. Modelling of solar distillation system with phase change material (PCM storage medium

    Directory of Open Access Journals (Sweden)

    Al-Hamadani Ali A.F.

    2014-01-01

    Full Text Available An experimental investigation on a passive solar still with myristic acid as phase change material (PCM is carried out to examine the effect of both the mass of PCM and basin water on the daily distillate output and efficiency of the system under indoor simulated condition. Basic energy balance equations are written to predict the water and glass temperatures, daily distillate output and instantaneous efficiency of the single slope solar distillation system with PCM. It is found that the higher mass of PCM with lower mass of water in the solar still basin significantly increases the daily yield and efficiency, but when the amount of PCM exceeds 20 kg productivity reduces. Therefore, a novel and simple of solar stills with PCM is proposed to enhance the overall productivity of the distillation system. The new solar still has increased the distillate output by 35-40%. The use of inner glass cover temperature for productivity prediction has also been investigated, and the prediction shows relatively better agreement with the experimental data.

  7. Low energy building with novel cooling unit using PCM

    Energy Technology Data Exchange (ETDEWEB)

    Jaber, Samar

    2012-02-13

    This thesis aims to reduce the energy consumption as well as greenhouse gases to the environment without negatively affecting the thermal comfort. In the present work, thermal, energetic and economic impacts of employing passive solar systems combined with energy conservation systems have been investigated. These energy systems have been integrated with a typical residential building located in three different climate zones in Europe and Middle East regions.Hour-by-hour energy computer simulations have been carried out using TRNSYS and INSEL programs to analyze the performance of integrated energy systems. Furthermore, IESU software module has been developed to simulate a novel cooling unit using Phase Change Material (PCM). This unit is named as Indirect Evaporative and Storage Unit (IESU). Thereafter, complete economic equations for the Life Cycle Cost (LCC) criterion have been formulated. Furthermore this criterion has been optimized for different variables as a function of thermal parameters and economic figures from local markets. An optimum design of both residential buildings and energy systems has great impact on energy consumption. In fact, results showed that the energy consumption is reduced by 85.62%, 86.33% and 74.05% in Berlin, Amman and Aqaba, respectively. Moreover, the LCC criterion is reduced by 41.85% in Berlin, 19.21% in Amman and 15.22% in Aqaba.The macro economic analysis shows that once this research is applied in one million typical residential buildings in the selected climate zones, the annual avoided CO{sub 2} emissions are estimated to be about 5.7 million Tons in Berlin. In Aqaba, around 2.96 million Tons CO{sub 2} emissions will be saved annually and in Amman about 2.98 million Tons will be reduced. The payback period from the achieved saving is 18 years, 11 years and 8.6 years in Amman, Aqaba and Berlin, respectively.

  8. Preventing accidents

    Science.gov (United States)

    2005-08-01

    As the most effective strategy for improving safety is to prevent accidents from occurring at all, the Volpe Center applies a broad range of research techniques and capabilities to determine causes and consequences of accidents and to identify, asses...

  9. A numerical method for PCM-based pin fin heat sinks optimization

    International Nuclear Information System (INIS)

    Pakrouh, R.; Hosseini, M.J.; Ranjbar, A.A.; Bahrampoury, R.

    2015-01-01

    Highlights: • Optimization of PCM-based heat sink by using the Taguchi method. • Derivation of optimal PCM percentage to reach the maximum critical time. • Optimization is performed for four different critical temperatures. • Effective design factors are fins’ height and fins’ number. • The optimum configuration depends on geometric properties and the critical temperature. - Abstract: This paper presents a numerical investigation on geometric optimization of PCM-based pin fin heat sinks. Paraffin RT44HC is used as PCM while the fins and heat sink base is made of aluminum. The fins act as thermal conductivity enhancers (TCEs). The main goal of the study is to obtain the configurations that maximize the heat sink operational time. An approach witch couples Taguchi method with numerical simulations is utilized for this purpose. Number of fins, fins height, fins thickness and the base thickness are parameters which are studied for optimization. In this study natural convection and PCM volume variation during melting process are considered in the simulations. Optimization is performed for different critical temperatures of 50 °C, 60 °C, 70 °C and 80 °C. Results show that a complex relation exists between PCM and TCE volume percentages. The optimal case strongly depends on the fins’ number, fins’ height and thickness and also the critical temperature. The optimum PCM percentages are found to be 60.61% (corresponds to 100 pin fin heat sink with 4 mm thick fins) for critical temperature of 50 °C and 82.65% (corresponds to 100 pin fin heat sink with 2 mm thick fins) for other critical temperatures

  10. Accident management for severe accidents

    International Nuclear Information System (INIS)

    Bari, R.A.; Pratt, W.T.; Lehner, J.; Leonard, M.; Disalvo, R.; Sheron, B.

    1988-01-01

    The management of severe accidents in light water reactors is receiving much attention in several countries. The reduction of risk by measures and/or actions that would affect the behavior of a severe accident is discussed. The research program that is being conducted by the US Nuclear Regulatory Commission focuses on both in-vessel accident management and containment and release accident management. The key issues and approaches taken in this program are summarized. 6 refs

  11. Development of Hollow Steel Ball Macro-Encapsulated PCM for Thermal Energy Storage Concrete.

    Science.gov (United States)

    Dong, Zhijun; Cui, Hongzhi; Tang, Waiching; Chen, Dazhu; Wen, Haibo

    2016-01-19

    The application of thermal energy storage with phase change materials (PCMs) for energy efficiency of buildings grew rapidly in the last few years. In this research, octadecane paraffin was served as a PCM, and a structural concrete with the function of indoor temperature control was developed by using a macro-encapsulated PCM hollow steel ball (HSB). The macro-encapsulated PCM-HSB was prepared by incorporation of octadecane into HSBs through vacuum impregnation. Test results showed that the maximum percentage of octadecane carried by HSBs was 80.3% by mass. The macro-encapsulated PCM-HSB has a latent heat storage capacity as high as 200.5 J/g. The compressive strength of concrete with macro-encapsulated PCM-HSB at 28 days ranged from 22 to 40 MPa. The indoor thermal performance test revealed that concrete with macro-encapsulated octadecane-HSB was capable of reducing the peak indoor air temperature and the fluctuation of indoor temperature. It can be very effective in transferring the heating and cooling loads away from the peak demand times.

  12. Methods of PCM microcapsules application and the thermal properties of modified knitted fabric

    Energy Technology Data Exchange (ETDEWEB)

    Nejman, Alicja, E-mail: anejman@iw.lodz.pl [Textile Research Institute, Scientific Department of Unconventional Technologies and Textiles, 5/15 Brzezinska St., 92-103 Lodz (Poland); Cieślak, Małgorzata [Textile Research Institute, Scientific Department of Unconventional Technologies and Textiles, 5/15 Brzezinska St., 92-103 Lodz (Poland); Gajdzicki, Bogumił [Textile Research Institute, Scientific Department of Textile Chemistry and Products Modification, 5/15 Brzezinska St., 92-103 Lodz (Poland); Goetzendorf-Grabowska, Bogna; Karaszewska, Agnieszka [Textile Research Institute, Scientific Department of Unconventional Technologies and Textiles, 5/15 Brzezinska St., 92-103 Lodz (Poland)

    2014-08-10

    Highlights: • We applied microcapsules containing n-octadecane for the modification of knitted fabric. • We used printing, coating and padding techniques for the application of microcapsules. • M-PCM application methods allow to regulate the thermal properties of textiles. • M-PCM application methods allow to regulate the air permeability properties of textiles. - Abstract: The aim of the study is to analyze the impact of application methods of microcapsules containing n-octadecane as phase change materials (M-PCM) on the thermal properties and air permeability of modified textile fabric. Polyester knitted fabric, printing, coating and padding methods and polymer pastes with 20 wt.% of M-PCM were used. For the assessment of modification effects the differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were used. DSC analysis showed that the highest enthalpy of phase transitions has printed fabric and the lowest padded fabric. The widest range of phase transitions temperatures was observed for printed fabric, slightly narrower for coated fabric and the narrowest for padded fabric. SEM analysis showed differences in the morphology of modified fabrics depending on incorporation techniques, which are compatible with differences in air permeability results. M-PCM application techniques allow to regulate the thermal and air permeability properties of fabric.

  13. Development of Hollow Steel Ball Macro-Encapsulated PCM for Thermal Energy Storage Concrete

    Directory of Open Access Journals (Sweden)

    Zhijun Dong

    2016-01-01

    Full Text Available The application of thermal energy storage with phase change materials (PCMs for energy efficiency of buildings grew rapidly in the last few years. In this research, octadecane paraffin was served as a PCM, and a structural concrete with the function of indoor temperature control was developed by using a macro-encapsulated PCM hollow steel ball (HSB. The macro-encapsulated PCM-HSB was prepared by incorporation of octadecane into HSBs through vacuum impregnation. Test results showed that the maximum percentage of octadecane carried by HSBs was 80.3% by mass. The macro-encapsulated PCM-HSB has a latent heat storage capacity as high as 200.5 J/g. The compressive strength of concrete with macro-encapsulated PCM-HSB at 28 days ranged from 22 to 40 MPa. The indoor thermal performance test revealed that concrete with macro-encapsulated octadecane-HSB was capable of reducing the peak indoor air temperature and the fluctuation of indoor temperature. It can be very effective in transferring the heating and cooling loads away from the peak demand times.

  14. Application of PCM energy storage in combination with night ventilation for space cooling

    International Nuclear Information System (INIS)

    Barzin, Reza; Chen, John J.J.; Young, Brent R.; Farid, Mohammed M.

    2015-01-01

    Highlights: • Night ventilation were tested in combination with PCM-impregnated gypsum boards. • The Price-based method were experimentally used to perform peak load shifting. • Importance of the application of a smart control were experimentally investigated. • A cost and energy saving up to 93% and 92% per day respectively were achieved. - Abstract: In recent years, as a result of the continuous increase in energy demand, the use of energy storage has become increasingly important. To address this problem, the application of phase change materials (PCM) in buildings has received attention because of their high energy storage density and their ease of incorporation in building envelopes. Despite large experimental works conducted on the application phase change materials in buildings, there is very little work done on this application in combination with night ventilation. In this study, the application of night ventilation in combination with PCM-impregnated gypsum boards for cooling purposes was experimentally investigated. Two identical test huts equipped with “smart” control systems were used for testing the concept. One hut was constructed using impregnated gypsum boards, while the other hut was finished with ordinary gypsum board. Initially an air conditioning (AC) unit, without night ventilation, was used in both huts to charge the PCM during low peak period, showing very little savings in electricity. However, when night ventilation was used to charge the PCM instead, a weekly electricity saving of 73% was achieved.

  15. The Possibility of Phase Change Materials (PCM Usage to Increase Efficiency of the Photovoltaic Modules

    Directory of Open Access Journals (Sweden)

    Klugmann-Radziemska Ewa

    2014-01-01

    Full Text Available Solar energy is widely available, free and inexhaustible. Furthermore this source of energy is the most friendly to the environment. For direct conversion of solar energy into useful forms like of electricity and thermal energy, respectively photovoltaic cells and solar collectors are being used. Forecast indicate that the first one solution will soon have a significant part in meeting the global energy demand. Therefore it is highly important to increase their efficiency in the terms of providing better energy conversion conditions. It can be obtain by designing new devices or by modifications of existing ones. This article presents general issues of photovoltaic installations exposed to work in high temperatures and basic concepts about phase change materials (PCMs. The paper presents the possibility of PCM usage to receive heat from the photovoltaic module. Specially designed test stand, consisting of PV module covered with a layer of PCM has been build and tested. Current-voltage characteristics of the cell without PCM material and with a layer of PCM have been presented. Authors also describe the results of the electrical and thermal characteristic of a coupled PV-PCM system.

  16. Experimental investigations on the cooling of a motorcycle helmet with phase change material (PCM

    Directory of Open Access Journals (Sweden)

    Fok S.C.

    2011-01-01

    Full Text Available The thermal comfort of motorcycle helmet during hot weather is important as it can affect the physiological and psychological condition of the rider. This paper examines the use of phase change material (PCM to cool a motorcycle helmet and presents the experimental investigations on the influences of the simulated solar radiation, wind speed, and heat generation rate on the cooling system. The result shows that the PCM-cooled helmet is able to prolong the thermal comfort period compared to a normal helmet. The findings also indicate that the heat generation from the head is the predominant factor that will affect the PCM melting time. Simulated solar radiation and ram-air due to vehicle motion under adiabatic condition can have very little influences on the PCM melting time. The results suggested that the helmet usage time would be influenced by the amount of heat generated from the head. Some major design considerations based on these findings have been included. Although this investigation focuses on the cooling of a motorcyclist helmet, the findings would also be useful for the development of PCM-cooling systems in other applications.

  17. Fuel rod failure during film boiling (PCM-1 test in the PBF)

    International Nuclear Information System (INIS)

    Domenico, W.F.; Stanley, C.J.; Mehner, A.S.

    1978-01-01

    The Power-Cooling-Mismatch (PCM) Test, PCM-1 was conducted in the Power Burst Facility (PFB) in March of 1978. The PCM Test Series is being conducted at the Idaho National Engineering Laboratory by EG and G Idaho, Inc., under contract to the USNRC and is designed to characterize the behavior of nuclear fuel rods operating under conditions of high power or low coolant flow or both leading to departure from nucleate boiling. The PCM-1 test was performed to provide in-pile data for a ''worst case'' PCM incident. The objective of this experiment was to study the behavior of a single pressurized water reactor (PWR) fuel rod subjected to a high-power and low flow environment which would result in cladding failure at full power. The ''worst case'' conditions established for the experiment consisted of a rod peak power of 78.7 kW/m and a coolant mass flux of 1356 kg/s.m 2 . Fuel temperatures at the stipulated operating conditions were such that a significant volume of molten fuel was present when failure occurred which produced a high probability of molten fuel-coolant interaction (MFCI) with the possibility of a vapor explosion

  18. Development of Hollow Steel Ball Macro-Encapsulated PCM for Thermal Energy Storage Concrete

    Science.gov (United States)

    Dong, Zhijun; Cui, Hongzhi; Tang, Waiching; Chen, Dazhu; Wen, Haibo

    2016-01-01

    The application of thermal energy storage with phase change materials (PCMs) for energy efficiency of buildings grew rapidly in the last few years. In this research, octadecane paraffin was served as a PCM, and a structural concrete with the function of indoor temperature control was developed by using a macro-encapsulated PCM hollow steel ball (HSB). The macro-encapsulated PCM-HSB was prepared by incorporation of octadecane into HSBs through vacuum impregnation. Test results showed that the maximum percentage of octadecane carried by HSBs was 80.3% by mass. The macro-encapsulated PCM-HSB has a latent heat storage capacity as high as 200.5 J/g. The compressive strength of concrete with macro-encapsulated PCM-HSB at 28 days ranged from 22 to 40 MPa. The indoor thermal performance test revealed that concrete with macro-encapsulated octadecane-HSB was capable of reducing the peak indoor air temperature and the fluctuation of indoor temperature. It can be very effective in transferring the heating and cooling loads away from the peak demand times. PMID:28787859

  19. Methods of PCM microcapsules application and the thermal properties of modified knitted fabric

    International Nuclear Information System (INIS)

    Nejman, Alicja; Cieślak, Małgorzata; Gajdzicki, Bogumił; Goetzendorf-Grabowska, Bogna; Karaszewska, Agnieszka

    2014-01-01

    Highlights: • We applied microcapsules containing n-octadecane for the modification of knitted fabric. • We used printing, coating and padding techniques for the application of microcapsules. • M-PCM application methods allow to regulate the thermal properties of textiles. • M-PCM application methods allow to regulate the air permeability properties of textiles. - Abstract: The aim of the study is to analyze the impact of application methods of microcapsules containing n-octadecane as phase change materials (M-PCM) on the thermal properties and air permeability of modified textile fabric. Polyester knitted fabric, printing, coating and padding methods and polymer pastes with 20 wt.% of M-PCM were used. For the assessment of modification effects the differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were used. DSC analysis showed that the highest enthalpy of phase transitions has printed fabric and the lowest padded fabric. The widest range of phase transitions temperatures was observed for printed fabric, slightly narrower for coated fabric and the narrowest for padded fabric. SEM analysis showed differences in the morphology of modified fabrics depending on incorporation techniques, which are compatible with differences in air permeability results. M-PCM application techniques allow to regulate the thermal and air permeability properties of fabric

  20. A new approach to the criticality safety assessment of PCM at BNFL Sellafield

    International Nuclear Information System (INIS)

    Darby, Sam; Kirkwood, Dave

    2003-01-01

    Plutonium Contaminated Material (PCM) arises as a solid waste on the Sellafield Site and is packaged into 200 litre drums which are placed into interim surface storage arrays. These wastes may also contain 235 U. The traditional approach to criticality safety has been based on ''worst-case'' reactivity modelling. This has recently led to a number of difficulties by implying that the 230 g (Pu + 235 U) drum limit is very important for criticality safety and the assay instruments used to demonstrate compliance with the limit need a high level of safety reliability. Also, the reliability and accuracy of the assay results of historical or legacy PCM became an issue. The new focus on substantiation of safety related equipment in BNFL has highlighted reliability shortfalls for the assay instruments. To overcome these shortfalls, additional operational practices on the PCM handling regimes were introduced to give increased confidence in the fissile assay results. These practices significantly delayed processing PCM waste stocks and resulted in significant additional operator dose uptake. Thus there were strong reasons to improve the existing approach. This paper describes a new approach to the criticality modelling of PCM. (author)

  1. Numerical analysis of a PCM thermal storage system with varying wall temperature

    International Nuclear Information System (INIS)

    Halawa, E.; Bruno, F.; Saman, W.

    2005-01-01

    Numerical analysis of melting and freezing of a PCM thermal storage unit (TSU) with varying wall temperature is presented. The TSU under analysis consists of several layers of thin slabs of a PCM subjected to convective boundary conditions where air flows between the slabs. The model employed takes into account the variations in wall temperature along the direction of air flow as well as the sensible heat. The paper discusses typical characteristics of the melting/freezing of PCM slabs in an air stream and presents some results of the numerical simulation in terms of air outlet temperatures and heat transfer rates during the whole periods of melting and freezing. Considerations in the design of the TSU are also given

  2. Technical Basis for Implementation of the PCM-1B for Personnel Release at Tank Farms

    International Nuclear Information System (INIS)

    BROWN, R.L.

    1999-01-01

    The purpose of this document is to define the technical basis and implementing guidelines for using automated personnel contamination monitors, such as the PCM-1B, at the River Protection Project (RPP) in lieu of performing a hand-held instrument followed by a PCM-1B survey for personnel release from contamination areas requiring a beta-gamma whole body survey. This document provides the basis for full implementation of the PCM-1B release survey, without the supplemental hand and foot survey, as currently implemented at RPP. This document applies only to RPP facilities. This document does not provide the technical basis for determining the equivalency of an automated system to hand-held instruments, or to the effective counting capability of automated systems as such technical determinations are contained in TBTN: GDGH-9604-RLS-0015

  3. A new method for measuring the thermal regulatory properties of phase change material (PCM) fabrics

    International Nuclear Information System (INIS)

    Wan, X; Fan, J

    2009-01-01

    Several methods already exist for the measurement of the thermal regulatory properties of fabrics containing phase change materials (PCMs). However, they do not adequately simulate the actual use condition; consequently the measurements may not have relevance to the performance of PCM fabrics in actual use. Here we report on the development of a new method, which better simulates the real use situation. In this method, a hot plate, simulating the human body, generates a constant amount of heat depending on the type of human activity to be simulated. The hot plate covered by the PCM fabric is then exposed to a thermal transient simulating a wearer moving from one thermal environment to another; the changes of surface temperature and heat loss of the hot plate are then recorded and used to characterize the thermal regulatory properties of the PCM fabrics

  4. Experimental study of discharging PCM ceiling panels through nocturnal radiative cooling

    DEFF Research Database (Denmark)

    Bourdakis, Eleftherios; Péan, Thibault Q.; Gennari, Luca

    PhotoVoltaic/Thermal (PV/T) panels were used for cooling water through the principle of nocturnal radiative cooling. This water was utilised for discharging Phase Change Material (PCM) which was embedded in ceiling panels in a climate chamber. Three different sets of flow rates were examined...... for the solar and the PCM loops, for five days each. The highest examined water flow rate (210 l/h) in the PCM loop provided the best thermal environment in the climate chamber, namely 92% of the occupancy time was within the range of Category III of Standard EN 15251. Although the lowest examined water flow...... rate (96 l/h) in the solar loop provided the highest average cooling power, due to the significant variations in the weather conditions during the three experimental cases, made it impossible to determine to which extent the difference in the cooling power is due to the different water flow rate...

  5. Computational Fluid Dynamic Analysis of Enhancing Passenger Cabin Comfort Using PCM

    Science.gov (United States)

    Purusothaman, M.; Valarmathi, T. N.; Dada Mohammad, S. K.

    2016-09-01

    The main purpose of this study is to determine a cost effective way to enhance passenger cabin comfort by analyzing the effect of solar radiation of a open parked vehicle, which is exposed to constant solar radiation on a hot and sunny day. Maximum heat accumulation occurs in the car cabin due to the solar radiation. By means of computational fluid dynamics (CFD) analysis, a simulation process is conducted for the thermal regulation of the passenger cabin using a layer of phase change material (PCM) on the roof structure of a stationary car when exposed to ambient temperature on a hot sunny day. The heat energy accumulated in the passenger cabin is absorbed by a layer of PCM for phase change process. The installation of a ventilation system which uses an exhaust fan to create a natural convection scenario in the cabin is also considered to enhance passenger comfort along with PCM.

  6. A new method to determine thermophysical properties of PCM-concrete brick

    DEFF Research Database (Denmark)

    Cheng, Rui; Pomianowski, Michal Zbigniew; Wang, Xin

    2013-01-01

    . The equivalent specific heat distributions of 4 wt% and 6 wt% PCM-concrete brick were determined using this method. We found that the accuracy (the relative error of the calculated cp based on the inverse problem and their real values ranges from 10.43% to 19.4%) was acceptable for engineering use...... the shortcomings of using traditional testing methods to measure thermophysical properties of PCM-concrete brick. We then proposed a new method based on the inverse problem, which deals with the measurements of thermal conductivity and specific heat of PCM-concrete brick during the phase change process....... The influences of the temperature segments span and optimization algorithms were analyzed. The results showed that the Sequential Quadric Programming (SQP) method provides the highest accuracy and least complexity compared with the Particle Swarm Optimization and Genetic Optimization methods. Finally, we...

  7. Transient and cyclic effects on a PCM-cooled mobile device

    Directory of Open Access Journals (Sweden)

    Tso C.P.

    2015-01-01

    Full Text Available A mock handset with heat storage unit (HSU has been designed, fabricated, and experimented under various conditions to examine the effect of external heat sink on the handset’s transient temperature distribution, performance of the individual HSU under different power level and orientation, as well as under the more realistic cyclic heating. The cooling of the handset is through using a phase change material (PCM, n-eicosane, stored in the external HSU connected to the handset through a miniature heat pipe. The heat pipe channels the internal heat dissipation to the HSU where it is absorbed by the PCM. Results show that the temperature is significantly lowered with the PCM-based HSU.

  8. Solvation of monovalent anions in formamide and methanol: Parameterization of the IEF-PCM model

    International Nuclear Information System (INIS)

    Boees, Elvis S.; Bernardi, Edson; Stassen, Hubert; Goncalves, Paulo F.B.

    2008-01-01

    The thermodynamics of solvation for a series of monovalent anions in formamide and methanol has been studied using the polarizable continuum model (PCM). The parameterization of this continuum model was guided by molecular dynamics simulations. The parameterized PCM model predicts the Gibbs free energies of solvation for 13 anions in formamide and 16 anions in methanol in very good agreement with experimental data. Two sets of atomic radii were tested in the definition of the solute cavities in the PCM and their performances are evaluated and discussed. Mean absolute deviations of the calculated free energies of solvation from the experimental values are in the range of 1.3-2.1 kcal/mol

  9. The multi-element probabilistic collocation method (ME-PCM): Error analysis and applications

    International Nuclear Information System (INIS)

    Foo, Jasmine; Wan Xiaoliang; Karniadakis, George Em

    2008-01-01

    Stochastic spectral methods are numerical techniques for approximating solutions to partial differential equations with random parameters. In this work, we present and examine the multi-element probabilistic collocation method (ME-PCM), which is a generalized form of the probabilistic collocation method. In the ME-PCM, the parametric space is discretized and a collocation/cubature grid is prescribed on each element. Both full and sparse tensor product grids based on Gauss and Clenshaw-Curtis quadrature rules are considered. We prove analytically and observe in numerical tests that as the parameter space mesh is refined, the convergence rate of the solution depends on the quadrature rule of each element only through its degree of exactness. In addition, the L 2 error of the tensor product interpolant is examined and an adaptivity algorithm is provided. Numerical examples demonstrating adaptive ME-PCM are shown, including low-regularity problems and long-time integration. We test the ME-PCM on two-dimensional Navier-Stokes examples and a stochastic diffusion problem with various random input distributions and up to 50 dimensions. While the convergence rate of ME-PCM deteriorates in 50 dimensions, the error in the mean and variance is two orders of magnitude lower than the error obtained with the Monte Carlo method using only a small number of samples (e.g., 100). The computational cost of ME-PCM is found to be favorable when compared to the cost of other methods including stochastic Galerkin, Monte Carlo and quasi-random sequence methods

  10. Numerical study on the thermal performance of a ventilated facade with PCM

    International Nuclear Information System (INIS)

    Gracia, Alvaro de; Navarro, Lidia; Castell, Albert; Cabeza, Luisa F.

    2013-01-01

    A new type of ventilated facade (VF) with macro-encapsulated phase change material (PCM) in its air cavity is presented in this paper. Two identical house-like cubicles located in Puigverd de Lleida (Spain) were monitored during 2012, and in one of them, the VF with PCM was implemented in the south wall. The versatility of the facade allows the system to reduce both heating and cooling loads. During winter, the PCM increases the heat storage capacity of the system exposed to solar radiation and during summer the system can be used as a cold storage unit or as a night free cooling device. From the experimental winter campaign, important net electrical energy savings were registered due to the use of the VF. On the other hand, no net energy savings were achieved during summer due to excessive use of mechanical ventilation. In this paper, an own developed numerical model, based on finite control volume approach, was validated against experimental data and it is used to select the operational schedule of both solidification and melting processes in order to achieve net electrical energy savings. During the mild summer period the system presents a net energy supply of 2.49 MJ/day. This value would be increased by 61.6% if a wooden structure would have been used instead of the current metallic structure. Moreover, the high hysteresis of the PCM limits strongly the potential of the system in supplying cooling during the severe summer period. -- Highlights: • Numerical study of the thermal performance of a ventilated facade with PCM. • The study considers cooling purposes. • Operational schedule and use of fans during solidification of PCM optimization. • Net energy supply of 2.49 MJ/day during mild summer from the ventilated facade. • Storage efficiency would maximize with more mechanical ventilation during less time

  11. Numerical and experimental study on temperature control of solar panels with form-stable paraffin/expanded graphite composite PCM

    International Nuclear Information System (INIS)

    Luo, Zigeng; Huang, Zhaowen; Xie, Ning; Gao, Xuenong; Xu, Tao; Fang, Yutang; Zhang, Zhengguo

    2017-01-01

    Highlights: • A passive cooling PV-PCM system was developed. • Form-stable paraffin/EG composite PCM with high thermal conductivity was utilized. • Numerical simulation on the temperature of PV-PCM panel was carried out. • Effects of density were studied under the given weather conditions. - Abstract: Performance of photovoltaic (PV) panels is greatly affected by its operating temperature. And traditional active and passive cooling methods usually suffer from the disadvantages of external energy consumption, uneven temperature distribution and low thermal conductivity of phase change materials (PCMs). In this work, a PV-PCM system was developed to control the temperature of a PV panel by applying high thermal conductive form-stable paraffin (ZDJN-28)/EG composite PCM. The temperature, output voltage and power of a conventional PV panel and the PV-PCM panel were measured and compared. A numerical simulation model established by CFD software FLUENT was used to simulate the temperature change process of the PV-PCM panel with different material densities under the same conditions as experiment. The experiment results showed that compared with the temperature of the conventional PV panel, the temperature of the PV-PCM panel is kept below 50 °C for 200 min extended by 146 min with output power averagely increased by 7.28% in heating process. Simulated temperatures were in good agreement with experimental temperatures and indicated that the higher the density of the PCM is, the better the temperature management performance the PV panel could achieve. Besides, the PCM with density of 900 kg/m 3 was found sufficient to achieve a good temperature management performance when the average ambient temperature below 25 °C with the highest solar irradiation of 901 w/m 2 . In summary, this work is of great importance in the design of a PV-PCM system for temperature management of PV panels.

  12. PV-PCM integration in glazed building. Co-simulation and genetic optimization study

    DEFF Research Database (Denmark)

    Elarga, Hagar; Dal Monte, Andrea; Andersen, Rune Korsholm

    2017-01-01

    . An exploratory step has also been considered prior to the optimization algorithm: it evaluates the energy profiles before and after the application of PCM to PV module integrated in glazed building. The optimization analysis investigate parameters such as ventilation flow rates and time schedule to obtain......The study describes a multi-objective optimization algorithm for an innovative integration of forced ventilated PV-PCM modules in glazed façade buildings: the aim is to identify and optimize the parameters that most affect thermal and energy performances. 1-D model, finite difference method FDM...

  13. Initial Development of a Combined PCM and TABS Solution for Heat Storage and Cooling

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew; Heiselberg, Per; Jensen, Rasmus Lund

    2011-01-01

    to their significant thermal energy storage capabilities. The TABS has a potential for increasing the exploitation of the thermal mass of the building, which is rarely exposed for heat transfer.The main objective of this study is to optimize the location and amount of PCM in a hollow core deck in order to optimize...... heat storage capacity. A series of simulations were conducted using the COMSOL program to obtain knowledge regarding the dynamic heat storage capacity of the investigated hollow core deck element as a function of the amount and location of PCM. Furthermore, the dynamic heat storage capacity...

  14. Optimization of the level and range of working temperature of the PCM in the gypsum-microencapsulated PCM thermal energy storage unit for summer conditions in Central Poland

    Science.gov (United States)

    Łapka, P.; Jaworski, M.

    2017-10-01

    In this paper thermal energy storage (TES) unit in a form of a ceiling panel made of gypsum-microencapsulated PCM composite with internal U-shaped channels was considered and optimal characteristics of the microencapsulated PCM were determined. This panel may be easily incorporated into, e.g., an office or residential ventilation system in order to reduce daily variations of air temperature during the summer without additional costs related to the consumption of energy for preparing air parameters to the desired level. For the purpose of the analysis of heat transfer in the panel, a novel numerical simulator was developed. The numerical model consists of two coupled parts, i.e., the 1D which deals with the air flowing through the U-shaped channel and the 3D which deals with heat transfer in the body of the panel. The computational tool was validated based on the experimental study performed on the special set-up. Using this tool an optimization of parameters of the gypsum-microencapsulated PCM composite was performed in order to determine its most appropriate properties for the application under study. The analyses were performed for averaged local summer conditions in Warsaw, Poland.

  15. Nuclear accidents

    International Nuclear Information System (INIS)

    1987-01-01

    On 27 May 1986 the Norwegian government appointed an inter-ministerial committee of senior officials to prepare a report on experiences in connection with the Chernobyl accident. The present second part of the committee's report describes proposals for measures to prevent and deal with similar accidents in the future. The committee's evaluations and proposals are grouped into four main sections: Safety and risk at nuclear power plants; the Norwegian contingency organization for dealing with nuclear accidents; compensation issues; and international cooperation

  16. Dynamic Heat Storage and Cooling Capacity of a Concrete Deck with PCM and Thermally Activated Building System

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew; Heiselberg, Per; Jensen, Rasmus Lund

    2012-01-01

    This paper presents a heat storage and cooling concept that utilizes a phase change material (PCM) and a thermally activated building system (TABS) implemented in a hollow core concrete deck. Numerical calculations of the dynamic heat storage capacity of the hollow core concrete deck element...... in the article highlight the potential of using TABS and PCM in a prefabricated concrete deck element....

  17. Portable chlorophyll meter (PCM-502) values are related to total chlorophyll concentration and photosynthetic capacity in papaya (Carica papaya L.)

    Science.gov (United States)

    This study was carried out to verify the practical use of the portable chlorophyll meter-PCM502 (PCM) in two papaya cultivars with contrasting green coloring of the leaf blade (‘Golden’: yellowish-green; ‘Solo’: dark green). The relationship was studied between the photosynthetic process and leaf n...

  18. Post-accident core coolability of light water reactors

    International Nuclear Information System (INIS)

    Michio, I.; Teruo, I.; Tomio, Y.; Tsutao, H.

    1983-01-01

    A study on post-accident core coolability of LWR is discussed based on the practical fuel failure behavior experienced in NSRR, PBF, PNS and others. The fuel failure behavior at LOCA, RIA and PCM conditions are reviewed, and seven types of fuel failure modes are extracted as the basic failure mechanism at accident conditions. These are: cladding melt or brittle failure, molten UO 2 failure, high temperature cladding burst, low temperature cladding burst, failure due to swelling of molten UO 2 , failure due to cracks of embrittled cladding for irradiated fuel rods, and TMI-2 core failure. The post-accident core coolability at each failure mode is discussed. The fuel failures caused actual flow blockage problems. A characteristic which is common among these types is that the fuel rods are in the conditions violating the present safety criteria for accidents, and UO 2 pellets are in melting or near melting hot conditions when the fuel rods failed

  19. A new experimental method to determine specific heat capacity of inhomogeneous concrete material with incorporated microencapsulated-PCM

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew; Heiselberg, Per; Jensen, Rasmus Lund

    2014-01-01

    PCM. This paper describes the development of the new material and the experimental set-up to determine the specific heat capacity of the PCM concrete material. Moreover, various methods are proposed and compared to calculate the specific heat capacity of the PCM concrete. Finally, it is hoped......The study presented in this paper focuses on an experimental investigation of the specific heat capacity as a function of the temperature Cp (T) of concrete mixed with various amounts of phase change material (PCM). The tested specimens are prepared by directly mixing concrete and microencapsulated...... that this work can be used as an inspiration and guidance to perform measurements on the various composite materials containing PCM....

  20. Steam-based Charging-Discharging of a PCM Heat Storage

    African Journals Online (AJOL)

    fire7-

    2016-11-10

    Nov 10, 2016 ... 2Department of Energy and Process Engineering, Norwegian University of Science and. Technology ... Keywords: Solar energy, PCM storage, Latent heat storage, Two-phase thermosyphon. 1. ..... principle, with water as the working fluid at about 35-bar pressure. ... generator as applied to PTC systems.

  1. Water solar distiller productivity enhancement using concentrating solar water heater and phase change material (PCM

    Directory of Open Access Journals (Sweden)

    Miqdam T. Chaichan

    2015-03-01

    Full Text Available This paper investigates usage of thermal energy storage extracted from concentrating solar heater for water distillation. Paraffin wax selected as a suitable phase change material, and it was used for storing thermal energy in two different insulated treasurers. The paraffin wax is receiving hot water from concentrating solar dish. This solar energy stored in PCM as latent heat energy. Solar energy stored in a day time with a large quantity, and some heat retrieved for later use. Water’s temperature measured in a definite interval of time. Four cases were studied: using water as storage material with and without solar tracker. Also, PCM was as thermal storage material with and without solar tracker.The system working time was increased to about 5 h with sun tracker by concentrating dish and adding PCM to the system. The system concentrating efficiency, heating efficiency, and system productivity, has increased by about 64.07%, 112.87%, and 307.54%, respectively. The system working time increased to 3 h when PCM added without sun tracker. Also, the system concentrating efficiency increased by about 50.47%, and the system heating efficiency increased by about 41.63%. Moreover, the system productivity increased by about 180%.

  2. Evaluation of Probation Case Management (PCM) for Drug-Involved Women Offenders

    Science.gov (United States)

    Chan, Monica; Guydish, Joseph; Prem, Rosemary; Jessup, Martha A.; Cervantes, Armando; Bostrom, Alan

    2005-01-01

    Based on availability of case management services, drug-involved women offenders entered either a probation case management (PCM) intervention(n = 65) or standard probation(n = 44). Participants were placed in the case management condition until all slots were filled, then placed in standard probation until case management slots opened.…

  3. A Unified Buffering Management with Set Divisible Cache for PCM Main Memory

    Institute of Scientific and Technical Information of China (English)

    Mei-Ying Bian; Su-Kyung Yoon; Jeong-Geun Kim; Sangjae Nam; Shin-Dug Kim

    2016-01-01

    This research proposes a phase-change memory (PCM) based main memory system with an effective combi-nation of a superblock-based adaptive buffering structure and its associated set divisible last-level cache (LLC). To achieve high performance similar to that of dynamic random-access memory (DRAM) based main memory, the superblock-based adaptive buffer (SABU) is comprised of dual DRAM buffers, i.e., an aggressive superblock-based pre-fetching buffer (SBPB) and an adaptive sub-block reusing buffer (SBRB), and a set divisible LLC based on a cache space optimization scheme. According to our experiment, the longer PCM access latency can typically be hidden using our proposed SABU, which can significantly reduce the number of writes over the PCM main memory by 26.44%. The SABU approach can reduce PCM access latency up to 0.43 times, compared with conventional DRAM main memory. Meanwhile, the average memory energy consumption can be reduced by 19.7%.

  4. Seven Operation Modes and Simulation Models of Solar Heating System with PCM Storage Tank

    Directory of Open Access Journals (Sweden)

    Juan Zhao

    2017-12-01

    Full Text Available A physical model and dynamic simulation models of a solar phase-change heat storage heating system with a plate solar collector, phase-change material (PCM storage tank, plate heat exchanger, and auxiliary heat sources were established. A control strategy and numerical models for each of seven different operation modes that cover the entire heating season of the system were developed for the first time. The seven proposed operation modes are Mode 1: free cooling; Mode 2: reservation of heat absorbed by the solar collector in the PCM storage tank when there is no heating demand; Mode 3: direct supply of the heating demand by the solar collector; Mode 4: use of the heat absorbed by the solar collector to meet the heating demands, with the excess heat stored in the PCM storage tank; Mode 5: use of heat stored in the PCM storage tank to meet the heating demands, Mode 6: combined use of heat stored in the PCM storage tank and the auxiliary heating sources to meet the heating demands; and Mode 7: exclusive use of the auxiliary heat sources in order to meet the heating demands. Mathematical models were established for each of the above seven operation modes, taking into consideration the effects of the outdoor meteorological parameters and terminal load on the heating system. The real-time parameters for the entire heating season of the system with respect to the different operation modes can be obtained by solving the simulation models, and used as reference for the optimal design and operation of the actual system.

  5. Phase Change Material (PCM Application in a Modernized Korean Traditional House (Hanok

    Directory of Open Access Journals (Sweden)

    Jaewook Lee

    2018-03-01

    Full Text Available Social and policy interest in the modernization and revitalization of the Korean traditional house (Hanok has increased recently in Korea but its low thermal performance is one of its weaknesses. A feasibility study was conducted to evaluate the suitability of a Phase Change Material (PCM in a modernized Hanok. The research method involved a test of the heating and cooling load reduction and Predicted Mean Vote (PMV analysis for human comfort using an Esp-r simulation adopting multi variable PCM types as the building wall composite. The influence of PCMs on reducing the building energy load was assessed as a criterion for upgrading materials and infiltration to the passive house regulation. Compared to the base case, the heating and cooling load reduction ratio were as follows: Case 1 (old-Hanok, 10%; Case 2 (Korean Building Act, 21%; and Case 3 (passive house regulation, 53%. The optimal phase change temperatures of the PCMs were Case 1 (24–26 °C, Case 2 (23–25 °C and Case 3 (24–26 °C. PMV analysis showed that the use of a PCM can narrow the comfort range and centralize the optimal point. Therefore, the following contents can be presented as the design and material guidelines. First, the optimal PCM temperature can vary according to the combination of materials and local climate. In addition, the infiltration and insulation should be verified and a certain portion of them should be secured. Finally, the addition of insulation to a passive house level should be considered actively using a PCM as a supplement for net zero energy building (nZEB.

  6. Thermal performance of an integrated collector storage solar water heater (ICSSWH) with phase change materials (PCM)

    International Nuclear Information System (INIS)

    Chaabane, Monia; Mhiri, Hatem; Bournot, Philippe

    2014-01-01

    Highlights: • We study the effect of phase change materials integration on the thermal performances of an ICSSWH. • Two kinds and tree radiuses of the PCM layer are studied and the most appropriate design is presented. • The use of phase change materials in ICSSWH is determined to reduce the night thermal losses. • Myristic acid is the most appropriate PCM for this application regarding the daily and night operation. - Abstract: In this paper, we propose a numerical study of an integrated collector storage solar water heater (ICSSWH). Two numerical models in three-dimensional modeling are developed. The first one which describes a sensible heat storage unit (SHSU), allowing validating the numerical model. Based on the good agreement between numerical results and experimental data from literature, and as this type of solar water heater presents the disadvantage of its high night losses, we propose to integrate a phase change material (PCM) directly in the collector and to study its effect on the ICSSWH thermal performance. Indeed, a second 3D CFD model is developed and series of numerical simulations are conducted for two kind (myristic acid and RT42-graphite) and three radiuses (R = 0.2 m, R = 0.25 m and R = 0.3 m) of this PCM layer. Numerical results show that during the day-time, the latent heat storage unit (LHSU) performs better than the sensible one when myristic acid is used as PCM. Regarding the night operating of this solar system, it is found that the LHSU is more effective for both PCMs as it allows lower thermal losses and better heat preservation

  7. Normal accidents

    International Nuclear Information System (INIS)

    Perrow, C.

    1989-01-01

    The author has chosen numerous concrete examples to illustrate the hazardousness inherent in high-risk technologies. Starting with the TMI reactor accident in 1979, he shows that it is not only the nuclear energy sector that bears the risk of 'normal accidents', but also quite a number of other technologies and industrial sectors, or research fields. The author refers to the petrochemical industry, shipping, air traffic, large dams, mining activities, and genetic engineering, showing that due to the complexity of the systems and their manifold, rapidly interacting processes, accidents happen that cannot be thoroughly calculated, and hence are unavoidable. (orig./HP) [de

  8. The Drosophila Pericentrin-like-protein (PLP cooperates with Cnn to maintain the integrity of the outer PCM

    Directory of Open Access Journals (Sweden)

    Jennifer H. Richens

    2015-08-01

    Full Text Available Centrosomes comprise a pair of centrioles surrounded by a matrix of pericentriolar material (PCM. In vertebrate cells, Pericentrin plays an important part in mitotic PCM assembly, but the Drosophila Pericentrin-like protein (PLP appears to have a more minor role in mitotic fly cells. Here we investigate the function of PLP during the rapid mitotic cycles of the early Drosophila embryo. Unexpectedly, we find that PLP is specifically enriched in the outer-most regions of the PCM, where it largely co-localizes with the PCM scaffold protein Cnn. In the absence of PLP the outer PCM appears to be structurally weakened, and it rapidly disperses along the centrosomal microtubules (MTs. As a result, centrosomal MTs are subtly disorganized in embryos lacking PLP, although mitosis is largely unperturbed and these embryos develop and hatch at near-normal rates. Y2H analysis reveals that PLP can potentially form multiple interactions with itself and with the PCM recruiting proteins Asl, Spd-2 and Cnn. A deletion analysis suggests that PLP participates in a complex network of interactions that ultimately help to strengthen the PCM.

  9. Accident Statistics

    Data.gov (United States)

    Department of Homeland Security — Accident statistics available on the Coast Guard’s website by state, year, and one variable to obtain tables and/or graphs. Data from reports has been loaded for...

  10. Radiation accidents

    International Nuclear Information System (INIS)

    Nenot, J.C.

    1996-01-01

    Analysis of radiation accidents over a 50 year period shows that simple cases, where the initiating events were immediately recognised, the source identified and under control, the medical input confined to current handling, were exceptional. In many cases, the accidents were only diagnosed when some injuries presented by the victims suggested the radiological nature of the cause. After large-scale accidents, the situation becomes more complicated, either because of management or medical problems, or both. The review of selected accidents which resulted in severe consequences shows that most of them could have been avoided; lack of regulations, contempt for rules, human failure and insufficient training have been identified as frequent initiating parameters. In addition, the situation was worsened because of unpreparedness, insufficient planning, unadapted resources, and underestimation of psychosociological aspects. (author)

  11. A numerical study on the usage of phase change material (PCM) to prolong compressor off period in a beverage cooler

    International Nuclear Information System (INIS)

    Ezan, Mehmet Akif; Ozcan Doganay, Esra; Yavuz, Fazil Erinc; Tavman, Ismail Hakkı

    2017-01-01

    Highlights: • A 3D transient model is developed in a commercial CFD solver for vertical beverage cooler with PCM. • PCM slab is directly contacted with the airflow. • Regarding the run-time ratio best performance is achieved with 6 mm PCM slab. • Due to thermal inertia within the PCM domain, the VBC preserves its temperature for a long time. - Abstract: This study numerically investigates the influence of integration of a phase change material (PCM) slab inside a vertical beverage cooler (VBC) on the energy consumption, the thermal stability and flow characteristics of air inside the cooler. The PCM, water, slab is placed on the rear side of the flat plate roll bond evaporator with five different thicknesses, such as 2, 4, 6, 8, and 10 mm. In the current work, transient numerical analyses are performed with ANSYS-FLUENT software for an empty cooler. To simulate the on/off controller of the cooling system a dedicated user-defined-function (UDF) is implemented in the software. Unlike the counterparts in the recent literature, instead of reducing the problem into a 1D or 2D lumped models a three-dimensional cooler domain is simulated in a commercial CFD solver. The predictions are compared with the experimental measurement for the cooler without PCM regarding the transient variations of the mean temperatures of evaporator surface and the indoor air. Consequently, the parametric set of analyses deduced that the PCM integration into the cooler enhances the cooling performance of the VBC by prolonging compressor off duration. Moreover, during the compressor off time, PCM preserves the air temperature inside the refrigerated space in the desired range by limiting the sudden temperature increments.

  12. Sports Accidents

    CERN Multimedia

    Kiebel

    1972-01-01

    Le Docteur Kiebel, chirurgien à Genève, est aussi un grand ami de sport et de temps en temps médecin des classes genevoises de ski et également médecin de l'équipe de hockey sur glace de Genève Servette. Il est bien qualifié pour nous parler d'accidents de sport et surtout d'accidents de ski.

  13. Radiation accidents

    International Nuclear Information System (INIS)

    Poplavskij, K.K.; Smorodintseva, G.I.

    1978-01-01

    On the basis of a critical analysis of the available data on causes and consequences of radiation accidents (RA), a classification of RA by severity (five groups of accidents) according to biomedical consequences and categories of exposed personnel is proposed. A RA is defined and its main characteristics are described. Methods of RA prevention are proposed, as is a plan of specific measures to deal with RA in accordance with the proposed classification

  14. Numerical calibration and experimental validation of a PCM-Air heat exchanger model

    International Nuclear Information System (INIS)

    Stathopoulos, N.; El Mankibi, M.; Santamouris, Mattheos

    2017-01-01

    Highlights: • Development of a PCM-Air heat exchanger experimental unit and its numerical model. • Differential Scanning Calorimetry for PCM properties. • Ineptitude of DSC obtained heat capacity curves. • Creation of adequate heat capacity curves depending on heat transfer rates. • Confrontation of numerical and experimental results and validation of the model. - Abstract: Ambitious goals have been set at international, European and French level for energy consumption and greenhouse gas emissions decrease of the building sector. Achieving them requires renewable energy integration, a technology that presents however an important drawback: intermittent energy production. In response, thermal energy storage (TES) technology applications have been developed in order to correlate energy production and consumption of the building. Phase Change Materials (PCMs) have been widely used in TES applications as they offer a high storage density and adequate phase change temperature range. It is important to accurately know the thermophysical properties of the PCM, both for experimental (system design) and numerical (correct prediction) purposes. In this paper, the fabrication of a PCM – Air experimental prototype is presented at first, along with the development of a numerical model simulating the downstream temperature evolution of the heat exchanger. Particular focus is given to the calibration method and the validation of the model using experimental characterization results. Differential scanning calorimetry (DSC) is used to define the thermal properties of the PCM. Initial numerical results are underestimated compared to experimental ones. Various factors were investigated, pointing to the ineptitude of the heat capacity parameter, as DSC results depend on heating/cooling rates. Adequate heat capacity curves were empirically determined, depending on heat transfer rates and based on DSC results and experimental observations. The results of the proposed model

  15. Simulation Study of Discharging PCM Ceiling Panels through Night - time Radiative Cooling

    DEFF Research Database (Denmark)

    Bourdakis, Eleftherios; Kazanci, Ongun Berk; Grossule, F.

    2016-01-01

    demand. In the present simulation study, the coupling of nighttime radiative cooling with PCM for cooling an office room was investigated. For cooling water through nighttime radiative cooling two types of solar panels were utilized, an unglazed solar collector and photovoltaic/thermal (PV/T) panels...... provided by the PV/T panels was 43 W/m2 for Copenhagen, while for Milan and Athens it was 36 W/m2 and 34 W/m2, respectively. The cooling power of the unglazed solar collector was negligible. Finally, the total electricity produced in Copenhagen for the simulated period was 371 kWh, while for Milan...... and increase use of renewable energy sources. The aim is that by 2020 all new buildings should be nearly zero-energy buildings. A solution that could contribute to this is the combination of photovoltaic panels for the production of electricity and phase change material (PCM) for the reduction of peak cooling...

  16. Computational modeling of latent-heat-storage in PCM modified interior plaster

    Energy Technology Data Exchange (ETDEWEB)

    Fořt, Jan; Maděra, Jiří; Trník, Anton; Pavlíková, Milena; Pavlík, Zbyšek [Department of Materials Engineering and Chemistry, Faculty of Civil Engineering, Czech Technical University in Prague, Thákurova 7, 166 29 Prague (Czech Republic)

    2016-06-08

    The latent heat storage systems represent a promising way for decrease of buildings energy consumption with respect to the sustainable development principles of building industry. The presented paper is focused on the evaluation of the effect of PCM incorporation on thermal performance of cement-lime plasters. For basic characterization of the developed materials, matrix density, bulk density, and total open porosity are measured. Thermal conductivity is accessed by transient impulse method. DSC analysis is used for the identification of phase change temperature during the heating and cooling process. Using DSC data, the temperature dependent specific heat capacity is calculated. On the basis of the experiments performed, the supposed improvement of the energy efficiency of characteristic building envelope system where the designed plasters are likely to be used is evaluated by a computational analysis. Obtained experimental and computational results show a potential of PCM modified plasters for improvement of thermal stability of buildings and moderation of interior climate.

  17. Investigation of heat transfer inside a PCM-air heat exchanger: a numerical parametric study

    Science.gov (United States)

    Herbinger, Florent; Bhouri, Maha; Groulx, Dominic

    2017-07-01

    In this paper, the use of PCMs for thermal storage of energy in HVAC applications was investigated by studying numerically the thermal performance of a PCM-air heat exchanger. The PCM used in this study was dodecanoic acid. A symmetric 3D model, incorporating conductive and convective heat transfer (air only) as well as laminar flow, was created in COMSOL Multiphysics 5.0. Simulations examined the dependence of the heat transfer rate on the temperature and velocity of the incoming air as well as the size of the channels in the heat exchanger. Results indicated that small channels size lead to a higher heat transfer rates. A similar trend was also obtained for high incoming air temperature, whereas the heat transfer rate was less sensitive to the incoming air velocity.

  18. Utilization of the PCM latent heat for energy savings in buildings

    Science.gov (United States)

    Fořt, Jan; Trník, Anton; Pavlík, Zbyšek

    2017-07-01

    Increase of the energy consumption for buildings operation creates a great challenge for sustainable development issues. Thermal energy storage systems present promising way to achieve this goal. The latent heat storage systems with high density of thermal storage via utilization of phase change materials (PCMs) enable to improve thermal comfort of buildings and reduce daily temperature fluctuations of interior climate. The presented study is focused on the evaluation of the effect of PCM admixture on thermal performance of a cement-lime plaster. On the basis of the experimentally accessed properties of newly developed plasters, computational modeling is carried out in order to rate the acquired thermal improvement. The calculated results show that incorporation of 24 mass% of paraffinic wax based PCM decreased the energy demand of approx. 14.6%.

  19. Numerical study of a PCM-air heat exchanger's thermal performance

    Science.gov (United States)

    Herbinger, F.; Bhouri, M.; Groulx, D.

    2016-09-01

    In this paper, the use of PCMs in HVAC applications is investigated by studying numerically the thermal performance of a PCM-air heat exchanger. The PCM used in this study is dodecanoic acid. A symmetric 3D model, incorporating conductive and convective heat transfer (air only) as well as laminar flow, was created in COMSOL Multiphysics 5.0. Simulations examined the dependence of the heat transfer rate on the temperature and velocity of the incoming air as well as the size of the channels in the heat exchanger. Results indicated that small channels size lead to a higher heat transfer rates. A similar trend was also obtained for high incoming air temperature, whereas the heat transfer rate was less sensitive to the incoming air velocity.

  20. Unsupervised learning by spike timing dependent plasticity in phase change memory (PCM synapses

    Directory of Open Access Journals (Sweden)

    Stefano eAmbrogio

    2016-03-01

    Full Text Available We present a novel one-transistor/one-resistor (1T1R synapse for neuromorphic networks, based on phase change memory (PCM technology. The synapse is capable of spike-timing dependent plasticity (STDP, where gradual potentiation relies on set transition, namely crystallization, in the PCM, while depression is achieved via reset or amorphization of a chalcogenide active volume. STDP characteristics are demonstrated by experiments under variable initial conditions and number of pulses. Finally, we support the applicability of the 1T1R synapse for learning and recognition of visual patterns by simulations of fully connected neuromorphic networks with 2 or 3 layers with high recognition efficiency. The proposed scheme provides a feasible low-power solution for on-line unsupervised machine learning in smart reconfigurable sensors.

  1. PCM- data processing - description of the program TAPEDUMP for the computer HP-2100 S

    International Nuclear Information System (INIS)

    Ziegler, G.

    1978-01-01

    The assembler program TADEDUMP has the task, to preprocess PCM-data for further processing with a large computer and to put them in an output routine on magnetic tape with a measurement specific header. In the preprocessing the data can be reduced by selection and averaging. In the case of certain reading errors the data are discarded, but the synchronization is reestablished. (orig.) [de

  2. Thermal performance of a multiple PCM thermal storage unit for free cooling

    International Nuclear Information System (INIS)

    Mosaffa, A.H.; Infante Ferreira, C.A.; Talati, F.; Rosen, M.A.

    2013-01-01

    Highlights: ► Numerical analysis on the performance of a thermal storages as free cooling system. ► Employing multiple PCMs to enhance heat transfer rate in thermal storages. ► Using an effective heat capacity method, the phase change parameters are determined. ► The effect of the slabs size and air channel thickness on COP is investigated. - Abstract: As demand for refrigeration and air conditioning increased during the last decade, the opportunities have expanded for using thermal energy storage (TES) systems in an economically advantageous manner in place of conventional cooling plants. Many cool storage systems use phase change materials (PCMs) and achieve peak load shifting in buildings. This work presents numerical investigations of the performance enhancement of a free cooling system using a TES unit employing multiple PCMs. The TES unit is composed of a number of rectangular channels for the flowing heat transfer fluid, separated by PCM slabs. Using the effective heat capacity method, the melting and solidification of the PCM is solved. The forced convective heat transfer inside the channels is analyzed by solving the energy equation, which is coupled with the heat conduction equation in the container wall. The effect of design parameters such as PCM slab length, thickness and fluid passage gap on the storage performance is also investigated using an energy based optimization. The results show that a system which can guarantee comfort conditions for the climate of Tabriz, Iran has an optimum COP of 7.0. This could be achieved by a combination of CaCl 2 ·6H 2 O with RT25 with the optimum air channel thickness of 3.2 mm, length of 1.3 m and PCM slab thickness of 10 mm

  3. Experimental evaluation of passive cooling using phase change materials (PCM) for reducing overheating in public building

    Science.gov (United States)

    Ahmed, Abdullahi; Mateo-Garcia, Monica; McGough, Danny; Caratella, Kassim; Ure, Zafer

    2018-02-01

    Indoor Environmental Quality (IEQ) is essential for the health and productivity of building users. The risk of overheating in buildings is increasing due to increased density of occupancy of people and heat emitting equipment, increase in ambient temperature due to manifestation of climate change or changes in urban micro-climate. One of the solutions to building overheating is to inject some exposed thermal mass into the interior of the building. There are many different types of thermal storage materials which typically includes sensible heat storage materials such as concrete, bricks, rocks etc. It is very difficult to increase the thermal mass of existing buildings using these sensible heat storage materials. Alternative to these, there are latent heat storage materials called Phase Change Materials (PCM), which have high thermal storage capacity per unit volume of materials making them easy to implement within retrofit project. The use of Passive Cooling Thermal Energy Storage (TES) systems in the form of PCM PlusICE Solutions has been investigated in occupied spaces to improve indoor environmental quality. The work has been carried out using experimental set-up in existing spaces and monitored through the summer the months. The rooms have been monitored using wireless temperature and humidity sensors. There appears to be significant improvement in indoor temperature of up to 5°K in the room with the PCM compared to the monitored control spaces. The success of PCM for passive cooling is strongly dependent on the ventilation strategy employed in the spaces. The use of night time cooling to purge the stored thermal energy is essential for improved efficacy of the systems to reduce overheating in the spaces. The investigation is carried within the EU funded RESEEPEE project.

  4. PENAKERJA: GERAKAN ECOSCHOOL PADA SEKOLAH-SEKOLAH MUHAMMADIYAH DI PCM KARTASURA, SUKOHARJO

    Directory of Open Access Journals (Sweden)

    Siti Azizah Susilawati

    2015-09-01

    Full Text Available School as an institution where children get education, teaching and learning so that the school produced a superior human beings and qualified. Kartasura PCM is one of the flagship PCM in PDM Sukoharjo have elementary school level that has been known in the community, namely: MIM PK Muhammadiyah Kartasura, MIM Pucangan, Kertonatan MIM, MIM Gonilan and SDIT Al Kawthar Makamhaji Kartasura. The current fifth that grade school has a good reputation in the community. This community service aimed to increased awareness of the environment from all components of school at Muhammadiyah Elementary schools in PCM Kartasura. The first stage wasthe policy workshop school by school leaders and teachers, the second was distribute the grant of trash cans and posters, the third stage wasparticipatory education of Hole Infiltration Biopori and the fourth stage was monitoring. Monitoring results found that posters used as it should be, but the trash cans are still not being used properly, placement of trash cans were not side by side and still foundedthe organic waste mix with an organic waste in the same trash cans. This community service is an initial step the realization of school basedeco-school

  5. Preparation and Characterization of Inorganic PCM Microcapsules by Fluidized Bed Method

    Directory of Open Access Journals (Sweden)

    Svetlana Ushak

    2016-01-01

    Full Text Available The literature shows that inorganic phase change materials (PCM have been very seldom microencapsulated, so this study aims to contribute to filling this research gap. Bischofite, a by-product from the non-metallic industry identified as having good potential to be used as inorganic PCM, was microencapsulated by means of a fluidized bed method with acrylic as polymer and chloroform as solvent, after compatibility studies of both several solvents and several polymers. The formation of bischofite and pure MgCl2·6H2O microcapsules was investigated and analyzed. Results showed an efficiency in microencapsulation of 95% could be achieved when using 2 min of fluidization time and 2 kg/h of atomization flow. The final microcapsules had excellent melting temperatures and enthalpy compared to the original PCM, 104.6 °C and 95 J/g for bischofite, and 95.3 and 118.3 for MgCl2·6H2O.

  6. Influence of Microencapsulated Phase Change Material (PCM) Addition on (Micro) Mechanical Properties of Cement Paste

    Science.gov (United States)

    Schlangen, Erik

    2017-01-01

    Excessive cracking can be a serious durability problem for reinforced concrete structures. In recent years, addition of microencapsulated phase change materials (PCMs) to concrete has been proposed as a possible solution to crack formation related to temperature gradients. However, the addition of PCM microcapsules to cementitious materials can have some drawbacks, mainly related to strength reduction. In this work, a range of experimental techniques has been used to characterize the microcapsules and their effect on properties of composite cement pastes. On the capsule level, it was shown that they are spherical, enabling good distribution in the material during the mixing process. Force needed to break the microcapsules was shown to depend on the capsule diameter and the temperature, i.e., whether it is below or above the phase change temperature. On the cement paste level, a marked drop of compressive strength with increasing PCM inclusion level was observed. The indentation modulus has also shown to decrease, probably due to the capsules themselves, and to a lesser extent due to changes in porosity caused by their inclusion. Finally, a novel micro-cube splitting technique was used to characterize the tensile strength of the material on the micro-meter length scale. It was shown that the strength decreases with increasing PCM inclusion percentage, but this is accompanied by a decrease in measurement variability. This study will contribute to future developments of cementitious composites incorporating phase change materials for a variety of applications. PMID:28773225

  7. CoSyPCM - Solar combisystem with phase change materials - Annual report 2006; CoSyPCM Combi-systeme avec materiaux a changement de phase. Rapport annuel 2006

    Energy Technology Data Exchange (ETDEWEB)

    Citherlet, S.; Bony, J.

    2006-12-15

    The investigated objects are storage tanks of solar heating systems for domestic hot water preparation and space heating ('solar combisystems'). The question raised is whether the immersion of phase-change materials (PCM) contained in metal rods or spheres into the water storage tanks of such systems can be useful and bring reasonable advantages. The investigations took place by performing both measurements in the laboratory and computerized simulations using a model that was reported on in the annual report 2005 of the project. The present richly illustrated report describes the improvement of the simulation model by additionally considering the natural convection flow in the liquid phase of the PCM. This flow has a substantial effect on the heat transfer capacity rate from the storage water to the PCM or vice-versa. Simulations showed that this parameter has a decisive impact on the energy balance of the whole combisystem: if it is too small, the auxiliary heater has to be more frequently turned on to supplement the temporarily missing thermal energy to the heat consumer, as the solar energy stored in the PCM cannot be delivered sufficiently quickly to the user. The use of PCM in such storage tanks does not provide significant auxiliary energy savings in the cases investigated by the authors. However, more investigations could identify configurations offering energetic advantages, the authors claim. The report is supplemented by a life-cycle analysis of storage tanks with immersed PCM, to assess the environmental impact of the heat storage system.

  8. Phoenix light - Heating and cooling with phase-change materials; Phoenix light: Heizen und Kuehlen mit PCM - Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Haechler, E. [Suiselectra Ingenieurunternehmung AG, Basel (Switzerland); Schneider, B. [Hochschule Esslingen, University of Applied Sciences, Esslingen (Germany)

    2002-12-15

    This final report for the Swiss Federal Office of Energy (SFOE) deals with the use of phase-change materials (PCM) in buildings in order to help provide cooling in summer and heating in winter. General information on PCM and its use in the automotive industry, clothing, heating systems and office materials as well as in the electronics industry is provided. The physical and chemical basics are discussed and examples of PCM use in practice are provided. Also, work done in research institutes is mentioned. PCM systems from various manufacturers are noted. The 'phoenix light' system concept is discussed. The 'comfort cooler' concept is introduced and laboratory measurements made at the University of Applied Sciences in Esslingen, Germany, are discussed. Further, measurements made at an installation in an existing building are presented and discussed. Knowledge gained and the optimisation of the system are discussed. Finally, proposals for further work to be done are noted.

  9. Criticality accident:

    International Nuclear Information System (INIS)

    Canavese, Susana I.

    2000-01-01

    A criticality accident occurred at 10:35 on September 30, 1999. It occurred in a precipitation tank in a Conversion Test Building at the JCO Tokai Works site in Tokaimura (Tokai Village) in the Ibaraki Prefecture of Japan. STA provisionally rated this accident a 4 on the seven-level, logarithmic International Nuclear Event Scale (INES). The September 30, 1999 criticality accident at the JCO Tokai Works Site in Tokaimura, Japan in described in preliminary, technical detail. Information is based on preliminary presentations to technical groups by Japanese scientists and spokespersons, translations by technical and non-technical persons of technical web postings by various nuclear authorities, and English-language non-technical reports from various news media and nuclear-interest groups. (author)

  10. Empirical Validation of Heat Transfer Performance Simulation of Graphite/PCM Concrete Materials for Thermally Activated Building System

    Directory of Open Access Journals (Sweden)

    Jin-Hee Song

    2017-01-01

    Full Text Available To increase the heat capacity in lightweight construction materials, a phase change material (PCM can be introduced to building elements. A thermally activated building system (TABS with graphite/PCM concrete hollow core slab is suggested as an energy-efficient technology to shift and reduce the peak thermal load in buildings. An evaluation of heat storage and dissipation characteristics of TABS in graphite/PCM concrete has been conducted using dynamic simulations, but empirical validation is necessary to acceptably predict the thermal behavior of graphite/PCM concrete. This study aimed to validate the thermal behavior of graphite/PCM concrete through a three-dimensional transient heat transfer simulation. The simulation results were compared to experimental results from previous studies of concrete and graphite/PCM concrete. The overall thermal behavior for both materials was found to be similar to experiment results. Limitations in the simulation modeling, which included determination of the indoor heat transfer coefficient, assumption of constant thermal conductivity with temperature, and assumption of specimen homogeneity, led to slight differences between the measured and simulated results.

  11. Covering localization, mapping and evaluation of ducts, using Pipeline Current Mapper Methods (PCM); Localizacao, mapeamento e avaliacao de revestimento de dutos, utilizando o metodo Pipeline Current Mapper (PCM)

    Energy Technology Data Exchange (ETDEWEB)

    Furquim, Antonio Jorge [ESTEIO Engenharia e Aerolevantamentos S.A., Curitiba, PR (Brazil)

    2005-07-01

    Esteio Engenharia e Aerolevantamentos S.A., together with the PETROBRAS - Petroleo Brasileiro S.A., comes accomplishing the Location, Geo positioning, Mapping and Inspection of the Coating in more than 5.000 km of pipes in several areas of the country. The works come being executed seeking the obtaining of the real position of Ducts (They-Built) and the conditions in that meets the coating of the same ones. The risings base on the method Pipeline Current Mapper (PCM), using the equipment of production of Radio detection to locate and to inspect the conditions of the coating. This work presents the results, analyses, precision, benefits and difficulties found during the execution of the surveying. (author)

  12. Experimental and numerical investigation of a tube-in-tank latent thermal energy storage unit using composite PCM

    International Nuclear Information System (INIS)

    Meng, Z.N.; Zhang, P.

    2017-01-01

    Highlights: • A tube-in-tank latent thermal energy storage (LTES) unit using composite PCM is built. • Thermal performances of the LTES unit are experimentally and numerically studied. • Thermal performances of the LTES unit under different operation conditions are comparatively studied. • A 3D numerical model is established to study the heat transfer mechanisms of the LTES unit. - Abstract: Paraffin is a commonly used phase change material (PCM) which has been frequently applied for thermal energy storage. A tube-in-tank latent thermal energy storage (LTES) unit using paraffin as PCM is built in the present study, which can be used in many applications. In order to enhance the thermal performance of the LTES unit, the composite PCM is fabricated by embedding copper foam into pure paraffin. The performances of the LTES unit with the composite PCM during the heat charging and discharging processes are investigated experimentally, and a series of experiments are carried out under different inlet temperatures and inlet flow velocities of the heat transfer fluid (HTF). The temperature evolutions of the LTES unit are obtained during the experiments, and the time-durations, mean powers and energy efficiencies are estimated to evaluate the performance of the LTES unit. Meanwhile, a three-dimensional (3D) mathematical model based on enthalpy-porosity and melting/solidification models is established to investigate the heat transfer mechanisms of the LTES unit and the detailed heat transfer characteristics of the LTES unit are obtained. It can be concluded that the LTES unit with the composite PCM shows good heat transfer performance, and larger inlet flow velocity of the HTF and larger temperature difference between the HTF and PCM can enhance the heat transfer and benefit the thermal energy utilization. Furthermore, a LTES system with larger thermal energy storage capacity can be easily assembled by several such LTES units, which can meet versatile demands in

  13. Characterization of melting and solidification in a real scale PCM-air heat exchanger: Numerical model and experimental validation

    International Nuclear Information System (INIS)

    Dolado, Pablo; Lazaro, Ana; Marin, Jose M.; Zalba, Belen

    2011-01-01

    Research highlights: → A mathematical model of a PCM-air heat exchanger is developed and validated. → Validation range is 0.7-2.1 m/s for airflow and 8-45 o C for air inlet temperature. → Better λPCM lead to minor improvement as the main resistance is mostly on air side. → 1 o C mismatch in the PCM h-T curve could lead to errors of up to 20% in power. → The accuracy of material properties' data used as inputs in the model is stressed. -- Abstract: This paper describes the models developed to simulate the performance of a thermal energy storage (TES) unit in a real scale PCM-air heat exchanger, analyzing the heat transfer between the air and a commercially available and slab macroencapsulated phase change material (PCM). The models are based on one-dimensional conduction analysis, utilizing finite differences method, and implicit formulation, using the thermo-physical data of the PCM measured in the laboratory: enthalpy and thermal conductivity as functions of temperature. The models can take into account the hysteresis of the enthalpy curve and the convection inside the PCM, using effective conductivity when necessary. Two main paths are followed to accomplish the modeling: the thermal analysis of a single plate, and the thermal behavior of the entire TES unit. Comparisons between measurements and simulations are undertaken to evaluate the models. Average errors of less than 12% on thermal power are obtained for the entire cycle. Once the model is validated, a series of parameters and variables is studied to verify their influence on the behavior and design of the TES unit.

  14. Tchernobyl accident

    International Nuclear Information System (INIS)

    1986-06-01

    First, R.M.B.K type reactors are described. Then, safety problems are dealt with reactor control, behavior during transients, normal loss of power and behavior of the reactor in case of leak. A possible scenario of the accident of Tchernobyl is proposed: events before the explosion, possible initiators, possible scenario and events subsequent to the core meltdown (corium-concrete interaction, interaction with the groundwater table). An estimation of the source term is proposed first from the installation characteristics and the supposed scenario of the accident, and from the measurements in Europe; radiological consequences are also estimated. Radioactivity measurements (Europe, Scandinavia, Western Europe, France) are given in tables (meteorological maps and fallouts in Europe). Finally, a description of the site is given [fr

  15. Effect of thermal conductivities of shape stabilized PCM on under-floor heating system

    International Nuclear Information System (INIS)

    Cheng, Wenlong; Xie, Biao; Zhang, Rongming; Xu, Zhiming; Xia, Yuting

    2015-01-01

    Highlights: • HCE-SSPCM was prepared and used in under-floor heating system. • Enhancing thermal conductivity improved the efficiency of energy and space. • Too high thermal conductivity over a range was meaningless. • The economic benefits of the phase change energy storage system were the best. - Abstract: A kind of heat conduction-enhanced shape-stabilized PCM (HCE-SSPCM) was utilized in the under-floor heating system for house heating in winter. This system charges heat by using cheap nighttime electricity and provides heating needs throughout all day. The effect of thermal conductivity of the PCM on energy savings and economic benefits of the system were theoretically and experimentally studied. HCE-SSPCM plates, made of (solid paraffin + liquid paraffin)/high density polyethylene/expanded graphite, were introduced to a test room with under-floor heating system. And the operating characteristics of the system were compared with that of the non-phase change energy storage system and the conventional air conditioning system. The results showed that enhancing the thermal conductivity of PCM in a certain range could significantly improve the energy efficiency of the heating system and reduce the thickness of thermal insulating materials. But the improving effect was not obvious when the thermal conductivity was beyond 1.0 W/m K. The phase change energy storage system had a comfortable temperature environment and the best economic benefits among the three different heating types especially when the ratio of peak-valley electric price was high. Therefore, increasing the thermal conductivity of SSPCM will be of great significance for house heating

  16. Accident: Reminder

    CERN Multimedia

    2003-01-01

    There is no left turn to Point 1 from the customs, direction CERN. A terrible accident happened last week on the Route de Meyrin just outside Entrance B because traffic regulations were not respected. You are reminded that when travelling from the customs, direction CERN, turning left to Point 1 is forbidden. Access to Point 1 from the customs is only via entering CERN, going down to the roundabout and coming back up to the traffic lights at Entrance B

  17. Verification and validation of decision support software: Expert Choice{trademark} and PCM{trademark}

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Q.H.; Martin, J.D.

    1994-11-04

    This report documents the verification and validation of two decision support programs: EXPERT CHOICE{trademark} and PCM{trademark}. Both programs use the Analytic Hierarchy Process (AHP) -- or pairwise comparison technique -- developed by Dr. Thomas L. Saaty. In order to provide an independent method for the validating the two programs, the pairwise comparison algorithm was developed for a standard mathematical program. A standard data set -- selecting a car to purchase -- was used with each of the three programs for validation. The results show that both commercial programs performed correctly.

  18. Laboratory Testing of Solar Combi System with Compact Long Term PCM Heat Storage

    DEFF Research Database (Denmark)

    Johansen, Jakob Berg; Englmair, Gerald; Dannemand, Mark

    2016-01-01

    To enable the transition from fossil fuels as a primary heat source for domestic hot water preparation and space heating solar thermal energy has great potential. The heat from the sun has the disadvantage that it is not always available when there is a demand. To solve this mismatch a thermal...... seasonal storage can be used to store excess heat from the summer to the winter when the demand is higher than the supply. Installing a long term thermal storage in a one family house it needs to be compact and sensible heat storages are not suitable. A latent heat storage with a phase change material (PCM...

  19. Microencapsulated PCM slurry for heat transfer media. 4. Reduction of undercooling

    International Nuclear Information System (INIS)

    Akino, Norio; Nakano, Fumihiko; Kubo, Shinji; Nagashima, Akira; Sagiya, Syojiro; Nakanishi, Masayuki.

    1997-01-01

    New heat transfer media with large heat capacity is under development, using a slurry of microencapsulated-phase-change-material (MCPCM) mixed into carrying liquid. To prepare stable MCPCM slurry, fatty acid is selected as PCM owing to relatively large density, and diameter of MCPCM particles are below 10 μm. The temperature difference between melting and freezing points, the so-called undercooling becomes remarkable. To reduce the undercooling, an additive is mixed into fatty acid to introduce nucleation cites. It is concluded that Hexatriacontane is effective to remove undercooling of microencapsulated Lauric acid, Myristic acid and their mixture, and Sebacic acid is effective for Lauric acid. (author)

  20. Comparative study of two weir type cascade solar stills with and without PCM storage using energy and exergy analysis

    International Nuclear Information System (INIS)

    Sarhaddi, Faramarz; Farshchi Tabrizi, Farshad; Aghaei Zoori, Halimeh; Mousavi, Seyed Amir Hossein Seyed

    2017-01-01

    Highlights: • Performance evaluation of cascade solar stills with PCM storage is carried out. • Model of cascade solar still is weir type. • Present study is based on numerical simulation. • Effect of operating parameters is studies on yield, energy and exergy efficiencies. - Abstract: In this paper, the comparative study of energy and exergy performance of two weir type cascade solar stills with and without PCM storage in sunny and semi-cloudy days is carried out. The governing equations of energy analysis include a set of nonlinear equations which is obtained by writing energy balance for the various components of a solar still (i.e. glass cover, brackish water, absorber plate, phase change materials). A detailed exergy analysis is carried out and various irreversibility rates in the solar still system and its exergy efficiency are introduced. In order to solve the governing equations a computer simulation program is developed. The results of a numerical simulation of the present study are in good agreement with the experimental data of previous literatures. The numerical results of the present study show that the energy and exergy performance of solar still without PCM storage is better than the solar still with PCM storage in sunny days. On the other hand, the solar still with PCM storage is preferred for semi-cloudy days due to its better energy and exergy performance. The maximum value of the energy and exergy efficiencies of the solar still without PCM for a typical sunny day are 76.69% and 6.53%, respectively. While, the maximum energy and exergy efficiencies of the solar still with PCM for a sample semi-cloudy day are 74.35% and 8.59%, respectively. Furthermore, it is observed that the highest irreversibility rate belongs to the absorber plate and its value for the solar still without PCM on typical sunny day and the solar still with PCM on semi-cloudy days is 83.1% and 78.8% of the whole of system irreversibility rates, respectively. Whereas, the

  1. Experimental test of a hot water storage system including a macro-encapsulated phase change material (PCM)

    Science.gov (United States)

    Mongibello, L.; Atrigna, M.; Bianco, N.; Di Somma, M.; Graditi, G.; Risi, N.

    2017-01-01

    Thermal energy storage systems (TESs) are of fundamental importance for many energetic systems, essentially because they permit a certain degree of decoupling between the heat or cold production and the use of the heat or cold produced. In the last years, many works have analysed the addition of a PCM inside a hot water storage tank, as it can allow a reduction of the size of the storage tank due to the possibility of storing thermal energy as latent heat, and as a consequence its cost and encumbrance. The present work focuses on experimental tests realized by means of an indoor facility in order to analyse the dynamic behaviour of a hot water storage tank including PCM modules during a charging phase. A commercial bio-based PCM has been used for the purpose, with a melting temperature of 58°C. The experimental results relative to the hot water tank including the PCM modules are presented in terms of temporal evolution of the axial temperature profile, heat transfer and stored energy, and are compared with the ones obtained by using only water as energy storage material. Interesting insights, relative to the estimation of the percentage of melted PCM at the end of the experimental test, are presented and discussed.

  2. Numerical study for enhancing the thermal conductivity of phase change material (PCM) storage using high thermal conductivity porous matrix

    International Nuclear Information System (INIS)

    Mesalhy, Osama; Lafdi, Khalid; Elgafy, Ahmed; Bowman, Keith

    2005-01-01

    In this paper, the melting process inside an irregular geometry filled with high thermal conductivity porous matrix saturated with phase change material PCM is investigated numerically. The numerical model is resting on solving the volume averaged conservation equations for mass, momentum and energy with phase change (melting) in the porous medium. The convection motion of the liquid phase inside the porous matrix is solved considering the Darcy, Brinkman and Forchiemer effects. A local thermal non-equilibrium assumption is considered due to the large difference in thermal properties between the solid matrix and PCM by applying a two energy equation model. The numerical code shows good agreement for pure PCM melting with another published numerical work. Through this study it is found that the presence of the porous matrix has a great effect on the heat transfer and melting rate of the PCM energy storage. Decreasing the porosity of the matrix increases the melting rate, but it also damps the convection motion. It is also found that the best technique to enhance the response of the PCM storage is to use a solid matrix with high porosity and high thermal conductivity

  3. Thermal energy and economic analysis of a PCM-enhanced household envelope considering different climate zones in Morocco

    Science.gov (United States)

    Kharbouch, Yassine; Mimet, Abdelaziz; El Ganaoui, Mohammed; Ouhsaine, Lahoucine

    2018-07-01

    This study investigates the thermal energy potentials and economic feasibility of an air-conditioned family household-integrated phase change material (PCM) considering different climate zones in Morocco. A simulation-based optimisation was carried out in order to define the optimal design of a PCM-enhanced household envelope for thermal energy effectiveness and cost-effectiveness of predefined candidate solutions. The optimisation methodology is based on coupling Energyplus® as a dynamic simulation tool and GenOpt® as an optimisation tool. Considering the obtained optimum design strategies, a thermal energy and economic analysis are carried out to investigate PCMs' integration feasibility in the Moroccan constructions. The results show that the PCM-integrated household envelope allows minimising the cooling/heating thermal energy demand vs. a reference household without PCM. While for the cost-effectiveness optimisation, it has been deduced that the economic feasibility is stilling insufficient under the actual PCM market conditions. The optimal design parameters results are also analysed.

  4. Prevention of pedestrian accidents.

    OpenAIRE

    Kendrick, D

    1993-01-01

    Child pedestrian accidents are the most common road traffic accident resulting in injury. Much of the existing work on road traffic accidents is based on analysing clusters of accidents despite evidence that child pedestrian accidents tend to be more dispersed than this. This paper analyses pedestrian accidents in 573 children aged 0-11 years by a locally derived deprivation score for the years 1988-90. The analysis shows a significantly higher accident rate in deprived areas and a dose respo...

  5. Experimental Study on the Thermal Response of PCM Energy Storage Block with Hole Ventilation

    Directory of Open Access Journals (Sweden)

    Sunqi Zhuang

    2015-01-01

    Full Text Available Under the condition of Nanjing, the effect by the velocity variation of night ventilation on the thermal response of the south wall built by phase-change materials (PCMs blocks with different configurations has been investigated and analyzed. It shows that the thermal performance when the PCM is placed nearby inner side in hollow block is better than that of the outer side. Meanwhile, the maximum amplitude of the temperature on the interior surface when the PCM is placed at the inner side is 58.3% higher than that of the outer side. The optimal flow velocity of both A and B is 2 m/s. Meanwhile, the minimum amplitudes of the temperature on the interior surface are 1.74°C and 3.72°C as well as the retardation coefficients are 8 h and 7 h. Compared to the structure configuration without ventilation, the heat flow was reduced 38.2% and 29.3%, respectively, and the equivalent heat resistance increased by 115.8% and 88.6%.

  6. Temperature stabilisation in Fischer–Tropsch reactors using phase change material (PCM)

    International Nuclear Information System (INIS)

    Odunsi, Ademola O.; O'Donovan, Tadhg S.; Reay, David A.

    2016-01-01

    The Fischer–Tropsch (FT) reaction is highly exothermic. The exothermicity combined with a high sensitivity of product selectivity to temperature constitute the main challenges in the design of FT reactors. Temperature control is particularly critical to the process in order to ensure longevity of the catalyst, optimise the product distribution, and to ensure thermo-mechanical reliability of the entire process. The use of encapsulated, Phase Change Material (PCM), in conjunction with a supervisory temperature control mechanism, could help mitigate these challenges and intensify the heat transport from the reactor. A 2D-axisymmetric, pseudo-homogeneous, steady-state model, with the dissipation of the enthalpy of reaction into an isothermal PCM sink, in a wall-cooled, single-tube fixed bed reactor is presented. Effective temperature control shows a shift in thermodynamic equilibrium, favouring the selectivity of longer chain hydrocarbons (C_5_+) to the disadvantage of CH_4 selectivity-a much desired outcome in the hydrocarbon Gas-to-Liquid (GTL) industry. - Highlights: • Phase change material is used to control temperature in a Fischer–Tropsch reactor. • Effective temperature control favours the production of C_5_+ over CH_4. • A 2D-axisymmetric, steady-state model is presented. • The model is verified against similar experimental work done in literature.

  7. Experimental investigation of novel indirect solar cooker with indoor PCM thermal storage and cooking unit

    International Nuclear Information System (INIS)

    Hussein, H.M.S.; El-Ghetany, H.H.; Nada, S.A.

    2008-01-01

    In the present study, a novel indirect solar cooker with outdoor elliptical cross section, wickless heat pipes, flat-plate solar collector and integrated indoor PCM thermal storage and cooking unit is designed, constructed and tested under actual meteorological conditions of Giza, Egypt. Two plane reflectors are used to enhance the insolation falling on the cooker's collector, while magnesium nitrate hexahydrate (T m = 89 deg. C, latent heat of fusion 134 kJ/kg) is used as the PCM inside the indoor cooking unit of the cooker. It is found that the average daily enhancement in the solar radiation incident on the collector surface by the south and north facing reflectors is about 24%. Different experiments have been performed on the solar cooker without load and with different loads at different loading times to study the possibility of benefit from the virtues of the elliptical cross section wickless heat pipes and PCMs in indirect solar cookers to cook food at noon and evening and to keep food warm at night and in early morning. The results indicate that the present solar cooker can be used successfully for cooking different kinds of meals at noon, afternoon and evening times, while it can be used for heating or keeping meals hot at night and early morning

  8. Conceptual Design of Condenser using PCM as PCCS for APR1400

    International Nuclear Information System (INIS)

    Jung, Hwa-Young; Ko, A-Reum; Lee, Jeong Ik; Yoon, Ho Joon

    2016-01-01

    In this study, the conceptual design of the condenser using the phase change material (PCM) is proposed as another PCCS concept for PWRs. It is possible to install the condenser for the existing nuclear power plants under operation without PCCS. Most of all, this condenser has to be designed to reduce the pressure and temperature in the containment until the containment spray system is available. A feature of the condenser as shown in Fig. 2 is the composition of PCM and wire mesh connected with the fins to improve heat transfer. As the first step, a preliminary study was conducted to find the optimum design of the part at which the condensation occurs under the given conditions. The results show that the fin base area as well as the total heat transfer area of fins are generally in inversely proportional to the average condensation heat transfer coefficient. Also, the point at which the gradient is changed is when the flow regime is changed from wavy flow to turbulent flow. However, the number of fins shows the different trend. Thus, in order to achieve better average condensation heat transfer coefficient under the identical heat capacity condition, the shorter the fin length and the more fins are necessary for the optimum design the condenser in wavy flow region

  9. Conceptual Design of Condenser using PCM as PCCS for APR1400

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Hwa-Young; Ko, A-Reum; Lee, Jeong Ik [KAIST, Daejeon (Korea, Republic of); Yoon, Ho Joon [KUSTAR, Abu Dhabi (United Arab Emirates)

    2016-10-15

    In this study, the conceptual design of the condenser using the phase change material (PCM) is proposed as another PCCS concept for PWRs. It is possible to install the condenser for the existing nuclear power plants under operation without PCCS. Most of all, this condenser has to be designed to reduce the pressure and temperature in the containment until the containment spray system is available. A feature of the condenser as shown in Fig. 2 is the composition of PCM and wire mesh connected with the fins to improve heat transfer. As the first step, a preliminary study was conducted to find the optimum design of the part at which the condensation occurs under the given conditions. The results show that the fin base area as well as the total heat transfer area of fins are generally in inversely proportional to the average condensation heat transfer coefficient. Also, the point at which the gradient is changed is when the flow regime is changed from wavy flow to turbulent flow. However, the number of fins shows the different trend. Thus, in order to achieve better average condensation heat transfer coefficient under the identical heat capacity condition, the shorter the fin length and the more fins are necessary for the optimum design the condenser in wavy flow region.

  10. Durability of a fin-tube latent heat storage using high density polyethylene as PCM

    Science.gov (United States)

    Zauner, Christoph; Hengstberger, Florian; Etzel, Mark; Lager, Daniel; Hofmann, Rene; Walter, Heimo

    2017-10-01

    Polymers have rarely been used as storage materials in latent heat storages up to now. Thus, we systematically screened all polymers available on a large-scale, selected promising ones based on their theoretical properties and experimentally tested more than 50 candidates. We found that polyethylene, polyoxymethylene and polyamides are promising even as recycled material. Especially high density polyethylene (HDPE) turned out to be suitable as was shown by detailed thermophysical characterization including more than 1000 heating and cooling cycles for INEOS Rigidex HD6070EA. We built a storage with 170 kg HDPE and a total mass of 600 kg based on a fin-tube heat exchanger and characterized its energy capacity, power characteristics and temperature profiles using a thermal oil test rig. In total we performed 30 melting and crystallization cycles where the whole storage was above 100 °C for more than 140 hours. After usage we examined the interior of the storage by cutting it into various pieces. A thin layer of degradation was observed on the surfaces of the PCM which is most likely related to thermo-oxidative degeneration of HDPE. However, the bulk of the PCM is still intact as well as the heat exchanger itself.

  11. Radiation accidents

    International Nuclear Information System (INIS)

    Saenger, E.L.

    1986-01-01

    It is essential that emergency physicians understand ways to manage patients contaminated by radioactive materials and/or exposed to external radiation sources. Contamination accidents require careful surveys to identify the metabolic pathway of the radionuclides to guide prognosis and treatment. The level of treatment required will depend on careful surveys and meticulous decontamination. There is no specific therapy for the acute radiation syndrome. Prophylactic antibodies are desirable. For severely exposed patients treatment is similar to the supportive care given to patients undergoing organ transplantation. For high-dose extremity injury, no methods have been developed to reverse the fibrosing endarteritis that eventually leads to tissue death so frequently found with this type of injury. Although the Three Mile Island episode of March 1979 created tremendous public concern, there were no radiation injuries. The contamination outside the reactor building and the release of radioiodine were negligible. The accidental fuel element meltdown at Chernobyl, USSR, resulted in many cases of acute radiation syndrome. More than 100,000 people were exposed to high levels of radioactive fallout. The general principles outlined here are applicable to accidents of that degree of severity

  12. Chernobyl accident

    International Nuclear Information System (INIS)

    Bar'yakhtar, V.G.

    1995-01-01

    The monograph contains the catastrophe's events chronology, the efficiency assessed of those measures assumed for their localization as well as their environmental and socio-economic impact. Among materials of the monograph the results are presented of research on the radioactive contamination field forming as well as those concerning the investigation of biogeochemical properties of Chernobyl radionuclides and their migration process in the environment of the Ukraine. The data dealing with biological effects of the continued combined internal and external radioactive influence on plants, animals and human health under the circumstances of Chernobyl accident are of the special interest. In order to provide the scientific generalizing information on the medical aspects of Chernobyl catastrophe, the great part of the monograph is allotted to appraise those factors affecting the health of different population groups as well as to depict clinic aspects of Chernobyl events and medico-sanitarian help system. The National Programme of Ukraine for the accident consequences elimination and population social protection assuring for the years 1986-1993 and this Programme concept for the period up to the year 2000 with a special regard of the world community participation there

  13. Use of microPCM fluids as enhanced liquid coolants in automotive EV and HEV vehicles. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Mulligan, James C.; Gould, Richard D.

    2001-10-31

    Proof-of-concept experiments using a specific microPCM fluid that potentially can have an impact on the thermal management of automotive EV and HEV systems have been conducted. Samples of nominally 20-micron diameter microencapsulated octacosane and glycol/water coolant were prepared for testing. The melting/freezing characteristics of the fluid, as well as the viscosity, were determined. A bench scale pumped-loop thermal system was used to determine heat transfer coefficients and wall temperatures in the source heat exchanged. Comparisons were made which illustrate the enhancements of thermal performance, reductions of pumping power, and increases of heat transfer which occur with the microPCM fluid.

  14. PCM thermal storage design in buildings: Experimental studies and applications to solaria in cold climates

    International Nuclear Information System (INIS)

    Guarino, Francesco; Athienitis, Andreas; Cellura, Maurizio; Bastien, Diane

    2017-01-01

    Highlights: • This paper analyzes the performance of a building-integrated thermal storage system. • A wall opposing a glazed surface serves as phase change materials thermal storage. • The study is based on both experimental and simulation studies. • Heat is stored and released up to 6–8 h after solar irradiation. • Yearly heating requirements are reduced by 17% in a cold climate. - Abstract: As energy availability and demand often do not match, thermal energy storage plays a crucial role to take advantage of solar radiation in buildings: in particular, latent heat storage via phase-change material is particularly attractive due to its ability to provide high energy storage density. This paper analyzes the performance of a building-integrated thermal storage system to increase the energy performances of solaria in a cold climate. A wall opposing a highly glazed façade (south oriented) is used as thermal storage with phase change materials embedded in the wall. The study is based on both experimental and simulation studies. The concept considered is particularly suited to retrofits in a solarium since the PCM can be added as layers facing the large window on the vertical wall directly opposite. Results indicate that this PCM thermal storage system is effective during the whole year in a cold climate. The thermal storage allows solar radiation to be stored and released up to 6–8 h after solar irradiation: this has effects on both the reduction of daily temperature swings (up to 10 °C) and heating requirements (more than 17% on a yearly base). Coupling of the thermal storage system with natural ventilation is important during mid-seasons and summer to improve the PCM charge-discharge cycles and to reduce overheating. Results also show that cooling is less important than heating, reaching up to 20% of the overall annual energy requirements for the city of Montreal, Canada. Moreover, the phase change temperature range of the material used (18–24

  15. The use of lightweight aggregate saturated with PCM as a temperature stabilizing material for road surfaces

    International Nuclear Information System (INIS)

    Ryms, Michał; Lewandowski, Witold M.; Klugmann-Radziemska, Ewa; Denda, Hubert; Wcisło, Patrycja

    2015-01-01

    This paper presents the possibility of adding lightweight building aggregates to increase the stability – mechanical as well as thermal – of constructions and road objects. This stability can be achieved through saturating the porous granules of aggregate with a phase-change material (PCM) that allows the accumulation of solar heat. Intense solar radiation, especially during the summer, can cause the asphalt on road surfaces, bridges and parking lots to melt, thus protecting the structure from further overheating. The absence of asphalt layers results in thermal stress and strain conditions causes accelerated wear of road surface. Lightweight aggregate, previously used to reduce the weight of the structures, while maintaining the bearing capacity similar to that offered by conventional concrete structures, thereby gains a new functionality, as a temperature stabilizing material. The paper contains a review of several phase-change materials as well as a study justifying the choice of ceresin, a product of crude oil distillation, as a suitable material for such applications. Information about the aggregate and its possible applications, and a proposed method of saturating the aggregate with ceresin has also been collected and presented. With the help of quantitative research conducted through the use of differential scanning calorimetry, the characteristic of thermodynamic parameters of pure ceresin and expanded clay aggregate (Pollytag) saturated with ceresin was determined. Simulation tests conducted under real conditions on two asphalt surfaces (0.32 × 0.22 × 0.15 m), one of which contained the PCM while the other did not, have shown that even a small addition of ceresin (3% mass relative to the weight of the ground) causes a reduction in surface temperature of about 5 K within the tested temperature range of 318.15–338.15 K. - Highlights: • Road surface overheating on summer days may reach up to 344 K. • Solution against overheating through

  16. One thousand thermal cycles of magnesium chloride hexahydrate as a promising PCM for indoor solar cooking

    International Nuclear Information System (INIS)

    El-Sebaii, A.A.; Al-Heniti, S.; Al-Agel, F.; Al-Ghamdi, A.A.; Al-Marzouki, F.

    2011-01-01

    Research highlights: → Solar cookers must contain a PCM for cooking indoors. → MgCl 2 .6H 2 O when it cycled in a sealed container. → MgCl 2 .6H 2 O shows maximum of 0.1-3.5 o C of supercooling. → MgCl 2 .6H 2 O is a promising PCM for thermal energy storage. -- Abstract: Cooking is the major necessity for people all over the world. It accounts for a major share of energy consumption in developing countries. There is a critical need for the development of alternative, appropriate, affordable methods of cooking for use in developing countries. There is a history for solar cooking since 1650 where they are broadly divided into direct or focusing type, box-type and indirect or advanced solar cookers. The advanced solar cookers have the advantage of being usable indoors and thus solve one of the problems, which impede the social acceptance of solar cookers. The advanced type solar cookers are employing additional solar units that increase the cost. Therefore, the solar cooker must contain a heat storage medium to store thermal energy for use during off-sunshine hours. The main aim of this paper is to investigate the influence of the melting/solidification fast thermal cycling of commercial grade magnesium chloride hexahydrate (MgCl 2 .6H 2 O) on its thermo-physical properties; such as melting point and latent heat of fusion, to be used as a storage medium inside solar cookers. One thousand cycles have been performed in a sealed container under the extra water principle. The thermo-physical properties are measured using the differential scanning calorimetric technique. It is indicated that MgCl 2 .6H 2 O with the extra water principle and hermetically sealing of the container is a promising phase change material (PCM) for cooking indoors and during law intensity solar radiation periods. It is also found from the melting/solidification behavior of MgCl 2 .6H 2 O that it is solidify almost without supercooling; except in few cases where it showed maximum of 0

  17. Chernobyl accident

    International Nuclear Information System (INIS)

    Capra, D.; Facchini, U.; Gianelle, V.; Ravasini, G.; Bacci, P.

    1988-01-01

    The radioactive cloud released during the Chernobyl accident reached the Padana plain and Lombardy in the night of April 30th 1986; the cloud remained in the northern Italian skies for a few days and then disappeared either dispersed by winds and washed by rains. The evidence in atmosphere of radionuclides as Tellurium, Iodine, Cesium, was promptly observed. The intense rain, in first week of may, washed the radioactivity and fall-out contamined the land, soil, grass. The present work concerns the overall contamination of the Northern Italy territory and in particular the radioactive fall-out in the Lakes region. Samples of soil have been measured at the gamma spectroscope; a correlation is found between the radionuclides concentration in soil samples and the rain intensity, when appropriate deposition models are considered. A number of measurements has been done on the Como'lake ecosystem: sediments, plankton, fishes and the overall fall-out in the area has been investigated

  18. Self-reported accidents

    DEFF Research Database (Denmark)

    Møller, Katrine Meltofte; Andersen, Camilla Sloth

    2016-01-01

    The main idea behind the self-reporting of accidents is to ask people about their traffic accidents and gain knowledge on these accidents without relying on the official records kept by police and/or hospitals.......The main idea behind the self-reporting of accidents is to ask people about their traffic accidents and gain knowledge on these accidents without relying on the official records kept by police and/or hospitals....

  19. Accident Assessment

    International Nuclear Information System (INIS)

    Tripputi, Ivo; Lund, Ingemar

    2002-01-01

    There is a general feeling that decommissioning is an activity involving limited risks, compared to NPP operation, and in particular risks involving the general public. This is technically confirmed by licensing analysis and evaluations, where, once the spent fuel has been removed from the plant, the radioactivity inventory available to be released to the environment is very limited. Decommissioning activities performed so far in the world have also confirmed the first assumptions and no specific issue has been identified, in this field, to justify a completely new approach. Commercial interests in international harmonization, which could drive an in-depth discussion about the bases of this approach, are weak at the moment. However, there are several reasons why a discussion in an international framework about the Safety Case for decommissioning (and, in particular, about Accident Assessment) may be considered necessary and important, and why it may show some specific and peculiar aspects. An effort for a comprehensive and systematic D and D accident safety assessment of the decommissioning process is justified. It is necessary also to explore in a holistic way the aspects of industrial safety, and develop tools for the decision-making process optimization. The expected results are the implementation of appropriate and optimized protective measures in any event and of adequate on/off-site emergency plans for optimal public and workers protection. The experience from other decommissioning projects and large-scale industrial activities is essential to balance provisions and an Operating Experience review process (specific for decommissioning) should help to focus on real issues

  20. The effectiveness of organic PCM based on lauric acid from coconut oil and inorganic PCM based on salt hydrate CaCl2.6H2o as latent heat energy storage system in Indonesia

    Science.gov (United States)

    U, Sri Rahayu A.; Putri, Widya A.; Sutjahja, I. M.; Kurnia, D.; Wonorahardjo, S.

    2016-08-01

    A latent heat energy storage system utilizing phase change materials (PCM) is an alternative strategy to reduce the use of Air Conditioning (AC) system in big cities in Indonesia in order for energy conservation in the future. In this research we used two kinds of materials, namely organic PCM based on lauric acid from coconut oil (CO) and inorganic PCM based on salt hydrate CaCl2.6H2O, because they have thermophysical parameters suitable for human's thermal comfort application in the building. The CO which contained more than 50% lauric acid has the melting temperature (Tm ) of about 26 °C and heat entalphy (ΔH) around 103 kJ/kg, while CaCl2.6H2O has the melting point of 29 °C and heat entalphy of 190 kJ/kg. In this paper we report the effectiveness of those two kinds of PCM in reducing the air temperature as one of some criteria for human's thermal comfort. The experiments were performed in a close and adiabatic room and the time-temperature measurements were done automatically using Arduino microcontroller and LM35 temperature sensor connected to the PC.

  1. AIFTDS-8000 - A next generation PCM system: Concept through final design

    Science.gov (United States)

    Trover, William F.

    The development of a new modular PCM system composed of nineteen different types of functional modules is reported. The system is based on the loaf-of-bread packaging concept eliminating the classical fixed size box. The successful design of this packaging concept has been made possible by the building and testing of proof-of-concept models. Thermally driven PC payouts using multilayer PC boards with copper planes for power distribution and heat transfer are essential in achieving the high-end operating temperature of 85 C with a significant margin of safety. The modularity of the design permits low-cost periodic upgrades of key system elements by slice replacement without obsolescence of the majority of the hardware.

  2. Thermal performance assessment and improvement of a solar domestic hot water tank with PCM in the mantle

    DEFF Research Database (Denmark)

    Deng, Jie; Furbo, Simon; Kong, Weiqiang

    2018-01-01

    To develop an appropriate solar DHW (Domestic Hot Water) tank for residential dwellings and put it into the European solar thermal market for promotion, thermal performance tests of PCM (Phase Change Material) hot water storage tanks of both a prototype and an improved version with a water volume...

  3. EnergyPlus Hysteresis PCM Model: Cooperative Research and Development Final Report, CRADA Number CRD-16-639

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Edwin S. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2018-02-22

    Under the CRADA, NREL will provide assistance to NRGsim to debug and convert the EnergyPlus Hysteresis Phase Change Material ('PCM') model to C++ for adoption into the main code package of the EnergyPlus simulation engine.

  4. Using Paraffin PCM, Cryogel and TEC to Maintain Comet Surface Sample Cold from Earth Approach Through Retrieval

    Science.gov (United States)

    Choi, Michael K.

    2017-01-01

    An innovative thermal design concept to maintain comet surface samples cold (for example, 263 degrees Kelvin, 243 degrees Kelvin or 223 degrees Kelvin) from Earth approach through retrieval is presented. It uses paraffin phase change material (PCM), Cryogel insulation and thermoelectric cooler (TEC), which are commercially available.

  5. Exergy and energy analyses of two different types of PCM based thermal management systems for space air conditioning applications

    International Nuclear Information System (INIS)

    Tyagi, V.V.; Pandey, A.K.; Buddhi, D.; Tyagi, S.K.

    2013-01-01

    Highlights: ► Calcium chloride hexahydrate (CaCl 2 ⋅6H 2 O) as a PCM was used in this study. ► Two different capsulated system (HDPE based panel and balls) were designed. ► The results of CaCl 2 ⋅6H 2 O are very attractive for space air conditioning. ► Energy and exergy analyses for space cooling applications. - Abstract: This communication presents the experimental study of PCM based thermal management systems for space heating and cooling applications using energy and exergy analysis. Two different types of based thermal management system (TMS-I and TMS-II) using calcium chloride hexahydrate as the heat carrier has been designed, fabricated and studied for space heating and cooling applications at a typical climatic zone in India. In the first experimental arrangement the charging of PCM has been carried out with air conditioning system while discharging has been carried out using electric heater for both the thermal management systems. While in the second arrangement the charging of PCM has been carried out by solar energy and the discharging has been carried out by circulating the cooler ambient air during the night time. In the first experiment, TMS-I is found to be more effective than that of TMS-II while it was found to be reverse in the case of second experiment for both the charging and discharging processes not only for energetic but also for the exergetic performances

  6. Solar combi system with phase-change materials; CoSyPCM. Combi-systeme avec materiaux a changement de phase

    Energy Technology Data Exchange (ETDEWEB)

    Citherlet, S.; Bony, J.

    2007-02-15

    Within the framework of Task 32 of the Solar Heating and Cooling Programme of the International Energy Agency (IEA) we studied the potential of using Phase Change Material (PCM) in a solar combi system in the form of modules placed in a storage tank. The goal was to analyze the potential of latent heat storage in a water tank of a solar installation, in order to increase the performance or to reduce the storage volume. This report describes the methodology used and the results obtained during the analysis of the heat storage potential by latent heat. The following stages were carried out: (i) Development of a simulation model: As no reliable numerical model exists, we developed a dynamic model to simulate PCM modules of various PCM types and shapes. This simulation model takes into account the hysteresis, the subcooling as well as the internal convection of the PCM in a liquid phase. This model was implemented in an existing TRNSYS Type(60). (ii) Laboratory measurements: In order to validate the digital model we tested various configurations and different types of PCM to check the agreement between simulations and experimental results. This step was focused on the time-dependent temperature distribution in the PCM and in the storage tank in order to validate the numerical model. (iii) Solar combi system: The potential relevance of the PCM was tested by using a solar combi system (Arpege) both with and without PCM. An energy balance was established on the basis of a seven days uninterrupted use of Arpege in various conditions (meteorological conditions and domestic hot water draw-off). Following the validation of the numerical model, annual simulations were carried out. (iv) Environmental impacts: A life cycle analysis of this solar combi system both with and without PCM was carried out. This analysis takes into account materials of the Arpege installation, the PCM and its container, as well as auxiliary energy used. (author)

  7. Experimental investigation of a PCM-HP heat sink on its thermal performance and anti-thermal-shock capacity for high-power LEDs

    International Nuclear Information System (INIS)

    Wu, Yuxuan; Tang, Yong; Li, Zongtao; Ding, Xinrui; Yuan, Wei; Zhao, Xuezhi; Yu, Binhai

    2016-01-01

    Highlights: • A phase-change material (PCM) base heat pipe heat sink (PCM-HP heat sink) is designed. • The PCM-HP heat sink can significantly lower the LED heating rate and temperature. • The PCM-HP heat sink achieves a best anti-thermal-shock capacity in LED cyclic working modes. - Abstract: High-power LEDs demonstrate a number of benefits compared with conventional incandescent lamps and fluorescent lamps, including a longer lifetime, higher brightness and lower power consumption. However, owing to their severe high heat flux, it is difficult to develop effective thermal management of high-power LEDs, especially under cyclic working modes, which cause serious periodic thermal stress and limit further development. Focusing on the above problem, this paper designed a phase-change material (PCM) base heat pipe heat sink (PCM-HP heat sink) that consists of a PCM base, adapter plate, heat pipe and finned radiator. Different parameters, such as three types of interior materials to fill the heat sink, three LED power inputs and eight LED cyclic working modes, were separately studied to investigate the thermal performance and anti-thermal-shock capacity of the PCM-HP heat sink. The results show that the PCM-HP heat sink possesses remarkable thermal performance owing to the reduction of the LED heating rate and peak temperature. More importantly, an excellent anti-thermal-shock capacity of the PCM-HP heat sink is also demonstrated when applied in LED cyclic working modes, and this capacity demonstrates the best range.

  8. Accident information needs

    International Nuclear Information System (INIS)

    Hanson, D.J.; Arcieri, W.C.; Ward, L.W.

    1992-01-01

    A Five-step methodology has been developed to evaluate information needs for nuclear power plants under accident conditions and the availability of plant instrumentation during severe accidents. Step 1 examines the credible accidents and their relationships to plant safety functions. Step 2 determines the information personnel involved in accident management will need to understand plant behavior. Step 3 determines the capability of the instrumentation to function properly under severe accident conditions. Step 4 determines the conditions expected during the identified severe accidents. Step 5 compares the instrument capabilities and the severe accident conditions to evaluate the availability of the instrumentation to supply needed plant information

  9. Accident information needs

    Energy Technology Data Exchange (ETDEWEB)

    Hanson, D.J.; Arcieri, W.C.; Ward, L.W.

    1992-12-31

    A Five-step methodology has been developed to evaluate information needs for nuclear power plants under accident conditions and the availability of plant instrumentation during severe accidents. Step 1 examines the credible accidents and their relationships to plant safety functions. Step 2 determines the information personnel involved in accident management will need to understand plant behavior. Step 3 determines the capability of the instrumentation to function properly under severe accident conditions. Step 4 determines the conditions expected during the identified severe accidents. Step 5 compares the instrument capabilities and the severe accident conditions to evaluate the availability of the instrumentation to supply needed plant information.

  10. Accident information needs

    Energy Technology Data Exchange (ETDEWEB)

    Hanson, D.J.; Arcieri, W.C.; Ward, L.W.

    1992-01-01

    A Five-step methodology has been developed to evaluate information needs for nuclear power plants under accident conditions and the availability of plant instrumentation during severe accidents. Step 1 examines the credible accidents and their relationships to plant safety functions. Step 2 determines the information personnel involved in accident management will need to understand plant behavior. Step 3 determines the capability of the instrumentation to function properly under severe accident conditions. Step 4 determines the conditions expected during the identified severe accidents. Step 5 compares the instrument capabilities and the severe accident conditions to evaluate the availability of the instrumentation to supply needed plant information.

  11. Severe accident phenomena

    International Nuclear Information System (INIS)

    Jokiniemi, J.; Kilpi, K.; Lindholm, I.; Maekynen, J.; Pekkarinen, E.; Sairanen, R.; Silde, A.

    1995-02-01

    Severe accidents are nuclear reactor accidents in which the reactor core is substantially damaged. The report describes severe reactor accident phenomena and their significance for the safety of nuclear power plants. A comprehensive set of phenomena ranging from accident initiation to containment behaviour and containment integrity questions are covered. The report is based on expertise gained in the severe accident assessment projects conducted at the Technical Research Centre of Finland (VTT). (49 refs., 32 figs., 12 tabs.)

  12. Energy and Cost Saving of a Photovoltaic-Phase Change Materials (PV-PCM System through Temperature Regulation and Performance Enhancement of Photovoltaics

    Directory of Open Access Journals (Sweden)

    Ahmad Hasan

    2014-03-01

    Full Text Available The current research seeks to maintain high photovoltaic (PV efficiency and increased operating PV life by maintaining them at a lower temperature. Solid-liquid phase change materials (PCM are integrated into PV panels to absorb excess heat by latent heat absorption mechanism and regulate PV temperature. Electrical and thermal energy efficiency analysis of PV-PCM systems is conducted to evaluate their effectiveness in two different climates. Finally costs incurred due to inclusion of PCM into PV system and the resulting benefits are discussed in this paper. The results show that such systems are financially viable in higher temperature and higher solar radiation environment.

  13. Determination of the solar transmittance for the translucent shutter with PCM in liquid and solid state

    Science.gov (United States)

    Komerska, Anna; Ksionek, Dariusz; Rosiński, Marian

    2017-11-01

    This article presents results of the energy performance of an external translucent shading component integrated with a phase change material. A proposed technology is able to accumulate considerable amounts of energy in the latent heat by absorbing solar energy. Due to selective optical properties, much of the visible light is still transmitted through the facade. Experimental measurements were carried out in a laboratory set-up - testing thermal chamber, located in the Faculty of Building Services, Hydro and Environmental Engineering at Warsaw University of Technology. The main result of the experimental study was the evaluation of the average solar transmittance in the whole measured spectrum, as well as in the infrared and visible light. Since the shift in optical properties was observed when the material was undergoing a phase transition, the average spectral transmittances were measured for different states of matter of the PCM material. The tested shutter showed abilities to reduce and modulate daylight and solar heat gains in the indoor environment, which could contribute to considerable energy savings.

  14. Determination of the solar transmittance for the translucent shutter with PCM in liquid and solid state

    Directory of Open Access Journals (Sweden)

    Komerska Anna

    2017-01-01

    Full Text Available This article presents results of the energy performance of an external translucent shading component integrated with a phase change material. A proposed technology is able to accumulate considerable amounts of energy in the latent heat by absorbing solar energy. Due to selective optical properties, much of the visible light is still transmitted through the facade. Experimental measurements were carried out in a laboratory set–up – testing thermal chamber, located in the Faculty of Building Services, Hydro and Environmental Engineering at Warsaw University of Technology. The main result of the experimental study was the evaluation of the average solar transmittance in the whole measured spectrum, as well as in the infrared and visible light. Since the shift in optical properties was observed when the material was undergoing a phase transition, the average spectral transmittances were measured for different states of matter of the PCM material. The tested shutter showed abilities to reduce and modulate daylight and solar heat gains in the indoor environment, which could contribute to considerable energy savings.

  15. Preliminary investigation of thermal behaviour of PCM based latent heat thermal energy storage

    Science.gov (United States)

    Pop, Octavian G.; Fechete Tutunaru, Lucian; Bode, Florin; Balan, Mugur C.

    2018-02-01

    Solid-liquid phase change is used to accumulate and release cold in latent heat thermal energy storage (LHTES) in order to reduce energy consumption of air cooling system in buildings. The storing capacity of the LHTES depends greatly on the exterior air temperatures during the summer nights. One approach in intensifying heat transfer is by increasing the air's velocity. A LHTES was designed to be integrated in the air cooling system of a building located in Bucharest, during the month of July. This study presents a numerical investigation concerning the impact of air inlet temperatures and air velocity on the formation of solid PCM, on the cold storing capacity and energy consumption of the LHTES. The peak amount of accumulated cold is reached at different air velocities depending on air inlet temperature. For inlet temperatures of 14°C and 15°C, an increase of air velocity above 50% will not lead to higher amounts of cold being stored. For Bucharest during the hottest night of the year, a 100 % increase in air velocity will result in 5.02% more cold being stored, at an increase in electrical energy consumption of 25.30%, when compared to the reference values.

  16. Phase change Materials (PCM) microcapsules with different shell compositions: Preparation, characterization and thermal stability

    Energy Technology Data Exchange (ETDEWEB)

    Bayes-Garcia, L.; Ventola, L.; Cordobilla, R.; Benages, R.; Calvet, T.; Cuevas-Diarte, M.A. [Departament de Cristal.lografia, Mineralogia i Diposits Minerals, Facultat de Geologia, Universitat de Barcelona, Marti i Franques s/n, E-08028 Barcelona (Spain)

    2010-07-15

    In this study, phase change materials (Rubitherm registered RT 27) microcapsules were successfully obtained by two different methods. The main difference between them remains on the shell composition, as they are composed of different coacervates (Sterilized Gelatine/Arabic Gum for the SG/AG method and Agar-Agar/Arabic Gum for the AA/AG method). Microcapsules were thermally characterized by thermo-optical microscopy and differential scanning calorimetry. Using scanning electron microscopy, their spherical morphology (sphericity factor of 0.94-0.95) and their particle size distribution were determined, obtaining an average diameter of 12 {mu}m for the SG/AG method and lower values for the AA/AG method, where nanocapsules were also observed (average diameter of 4.3 {mu}m for the microcapsules and 104 nm for the nanocapsules). The thermal stability determination was carried out by Thermogravimetric analyses (TG) and the results show a high decomposition temperature, although the process takes places in four steps for the two mentioned methods. Moreover, the microcapsules obtained by the AA/AG method decompose in a more gradual way, as in the TG results a double step, instead of one, is appreciable. On the whole, the prepared microencapsulated PCM are totally capable of developing their role in thermal energy storage. (author)

  17. Performance Evaluation of a Demonstration System with PCM for Seasonal Heat Storage: Charge with Evacuated Tubular Collectors

    DEFF Research Database (Denmark)

    Englmair, Gerald; Furbo, Simon; Kong, Weiqiang

    with sunshine, the storage system performance was evaluated regarding charge with solar heat. It shows the system behavior during typical operation resulting from the control strategy. Heat transfer rates from the solar collector array (22.4 m2 aperture area) to the heat stores reached a peak of 19 kW, when PCM......A seasonal heat storage with phase change material (PCM) for a solar space heating and domestic hot water combisystem was tested in automated operation during charge with solar collectors. A water tank was operating as buffer heat storage. Based on measurements during a representative day...... temperatures were increasing with the state of charge. This is in contrast to maximization of solar yield. However, the energy conversion efficiency (65 %) of the collector array was satisfying. By considering pump electricity consumption, an overall performance ratio of 30.8 was obtained....

  18. Full Scale Investigation of the Dynamic Heat Storage of Concrete Decks with PCM and Enhanced Heat Transfer Surface Area

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew; Heiselberg, Per; Jensen, Rasmus Lund

    2013-01-01

    The paper presents the full-scale experimental investigation of the dynamic heat storage potential of the prefabricated hollow core deck elements with and without phase change material (PCM) and with and without increased bottom surface area of the decks. In the presented investigation five types...... of hollow core decks with different surfaces on the bottom are investigated: reference deck made of standard concrete and flat surface, deck with special mortar grooved tiles, deck with flat mortar tiles, deck with grooved mortar and phase change material tiles, deck with flat mortar and phase change...... material tiles. The experimental investigation presented in the paper is performed in the specially designed modified hot box apparatus that allows maintaining periodic steady-state tests with the full-scale concrete deck elements. The presented research investigates if the extended surface area and PCM...

  19. An efficient ab initio DFT and PCM assessment of the potentiometric selectivity of a salophen type Schiff base.

    Science.gov (United States)

    Demir, Serkan; Yilmaz, Hakan; Dilimulati, Maowulidan; Andaç, Müberra

    2014-06-01

    As a neutral carrier component for the preparation of a potentiometric membrane sensor, the affinity and selectivity of the salophen type Schiff base ligand obtained by 1:2 condensation of 2.3-diaminopyridine with salicylaldehyde toward a series of common cations has been fully examined by DFT/B3LYP and integral equation formalism polarizable continum model (IEF-PCM or only given with PCM as default input in the computations) in combination with the experimental data. Both the potentiometric measurements and DFT calculations have exhibited that the ionophore shows appreciable selectivity for Cu(2+) ion over other cations. Four different approaches where the last three are the modified version of each other have been evaluated and compared with potentiometric data. Based upon the results of comparison among the approaches suggested to verify the selective behavior of ionophore toward Cu(2+), PCM implemented approach having a whole computational groundwork has given well-matched results with the observed data and with the method augmented with experimental hydration energies. The foremost interferences were detected by determining potentiometric selectivity coefficients for each metal ion relative to Cu(2+) and compared to the results obtained by the DFT calculations.

  20. The Variations of Thermal Contact Resistance and Heat Transfer Rate of the AlN Film Compositing with PCM

    Directory of Open Access Journals (Sweden)

    Huann-Ming Chou

    2015-01-01

    Full Text Available The electrical industries have been fast developing over the past decades. Moreover, the trend of microelements and packed division multiplex is obviously for the electrical industry. Hence, the high heat dissipative and the electrical insulating device have been popular and necessary. The thermal conduct coefficient of aluminum nitride (i.e., AlN is many times larger than the other materials. Moreover, the green technology of composite with phase change materials (i.e., PCMs is worked as a constant temperature cooler. Therefore, PCMs have been used frequently for saving energy and the green environment. Based on the above statements, it does show great potential in heat dissipative for the AlN film compositing with PCM. Therefore, this paper is focused on the research of thermal contact resistance and heat transfer between the AlN/PCM pairs. According to the experimental results, the heat transfer decreases and the thermal contact resistance increases under the melting process of PCM. However, the suitable parameters such as contact pressures can be used to improve the above defects.

  1. Study of an electrical heating system with ductless air supply and shape-stabilized PCM for thermal storage

    International Nuclear Information System (INIS)

    Lin, Kunping; Zhang, Yinping; Di, Hongfa; Yang, Rui

    2007-01-01

    A kind of electrical floor heating system with a shape-stabilized phase change material (PCM) which has been studied at Tsinghua University in our previous studies, can provide space heating during the whole day and can be controlled conventionally. However, this is not suitable for office buildings where no space heating is needed at night. The effective control is very important for the heating system in such buildings. In this paper, we studied a kind of new electrical floor heating system with ductless air supply and shape-stabilized PCM for thermal storage in order to overcome the shortcomings of the passive under-floor electric heating system with thermal storage. In this paper, we investigated its thermal performance by experiments and simulation, calculated the effects of various factors and discussed the application feasibility in different climate regions. The results show that the total electrical energy consumption was shifted from the peak period to the off-peak period, which would provide significant economic benefits because of the different day and night electricity tariffs. The system can be designed by choosing PCM with proper melting temperature and be controlled by varying velocity of air supply in different conditions

  2. High-power direct ethylene glycol fuel cell (DEGFC) based on nanoporous proton-conducting membrane (NP-PCM)

    Science.gov (United States)

    Peled, E.; Livshits, V.; Duvdevani, T.

    We recently reported the development of a new nanoporous proton-conducting membrane (NP-PCM) and have applied it in a direct methanol fuel cell (DMFC) and in other direct oxidation fuel cells. The use of the NP-PCM in the DMFC offers several advantages over the Nafion-based DMFC including lower membrane cost, lower methanol crossover which leads to a much higher fuel utilization and higher conductivity. In this work, we found that the 90 °C swelling of the NP-PCM is only 5-8% and that the diffusion constant of methanol at 80-130 °C is higher by a factor of 1.5-3 than that of ethylene glycol (EG). The maximum power density of methanol/oxygen and EG/oxygen FCs equipped with a 100 μm thick NP-PCMs is 400 and 300 mW/cm 2 respectively, higher than that for a DMFC based on Nafion 115 (260 mW/cm 2 [Eletrochem. Solid-State Lett. 4 (4) (2001) A31]. This puts the DEGFC in direct competition with both DMFC and indirect methanol FC. Ethylene glycol (EG) is well known in the automobile industry and in contrast to methanol, its distribution infrastructure already exists, thus it is a promising candidate for practical electric vehicles.

  3. Solar Cooker Study under Oman Conditions for Late Evening Cooking Using Stearic Acid and Acetanilide as PCM Materials

    Directory of Open Access Journals (Sweden)

    Nagaraj Nayak

    2016-01-01

    Full Text Available Solar energy is an alternative source of nonrenewable energy in Oman. Sultanate of Oman government showed initiation into utilization of solar energy for domestic applications. Conversion of solar radiation into useful heat is the simplest application of solar energy, in which it can be used for late evening cooking. In this context, present work highlighted the design and development of solar cooker for Oman climatic conditions. The current work signifies usage of solar cooker for late evening cooking using stearic acid and acetanilide as phase change materials (PCM. Solar cooker parts are developed in-house and connected to water heating system compounded with evacuated tubes solar collector and storage tank. The circumference of cooker unit is incorporated with spiral stainless steel heat exchanger and annulus area of the pot is filled with PCM material. PCM releases heat at late evening and effective cooking up to 7:30 PM is noticed. The experimental results indicated the cooker efficiency of 30% and collector efficiency of 60–65% during the study. Overall, experiments showed satisfactory performance on the developed cooker.

  4. Nuclear accident dosimetry

    International Nuclear Information System (INIS)

    1982-01-01

    The film presents statistical data on criticality accidents. It outlines past IAEA activities on criticality accident dosimetry and the technical documents that resulted from this work. The film furthermore illustrates an international comparison study on nuclear accident dosimetry conducted at the Atomic Energy Research Establishment, Harwell, United Kingdom

  5. Nuclear accident dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-12-31

    The film presents statistical data on criticality accidents. It outlines past IAEA activities on criticality accident dosimetry and the technical documents that resulted from this work. The film furthermore illustrates an international comparison study on nuclear accident dosimetry conducted at the Atomic Energy Research Establishment, Harwell, United Kingdom

  6. Solar cooker of the portable parabolic type incorporating heat storage based on PCM

    International Nuclear Information System (INIS)

    Lecuona, Antonio; Nogueira, José-Ignacio; Ventas, Rubén; Rodríguez-Hidalgo, María-del-Carmen; Legrand, Mathieu

    2013-01-01

    Highlights: ► A portable utensil for commercial paraboloid type solar cookers is proposed. ► It includes heat storage with phase change materials (PCMs). ► The utensil is stored indoors in a thermally insulating box after charging. ► A thermal 1-D model predicts its performance in sunny days. ► The set allows cooking lunch, dinner and next day the breakfast for a family. - Abstract: This paper reviews relevant issues on solar cooking in order to define and evaluate an innovative layout of a portable solar cooker of the standard concentrating parabolic type that incorporates a daily thermal storage utensil. This utensil is formed by two conventional coaxial cylindrical cooking pots, an internal one and a larger external one. The void space between the two coaxial pots is filled with a phase change material (PCM) forming an intermediate jacket. The ensemble is thermally simulated using 1-D finite differences. A lumped elements model with convective heat transfer correlations is used for the internal behavior of the utensil, subjected to external radiation. This numerical model is used to study its transient behavior for the climatic conditions of Madrid, and validated with experimental data. Two options have been checked as possible PCMs: technical grade paraffin and erythritol. The results indicate that cooking the lunch for a family is possible simultaneously with heat storage along the day. Keeping afterwards the utensil inside an insulating box indoors allows cooking the dinner with the retained heat and also the next day breakfast. This expands the applicability of solar cooking and sustains the possibility of all the day around cooking using solar energy with a low inventory cost

  7. Myo-inositol based nano-PCM for solar thermal energy storage

    International Nuclear Information System (INIS)

    Singh, D.K.; Suresh, S.; Singh, H.; Rose, B.A.J.; Tassou, S.; Anantharaman, N.

    2017-01-01

    Highlights: • Properties of Myo-Inositol laden with Al_2O_3 and CuO nanoparticles was studied. • The melting point was found to increase for MI-A and decrease for MI-C. • MI interacted only physically on addition of NPs. • Mass changes were <3% after thermal cycling of MI-A and MI-C. • MI-A is more suited for thermal energy storage than MI-C. - Abstract: The thermo-physical behavior of Myo-Inositol (MI), (a sugar alcohol), was investigated as a potential material for developing more compact solar thermal energy storage systems than those currently available. This latent heat storage medium could be utilized for commercial and industrial applications using solar thermal energy storage in the temperature range of 160–260 °C, if its thermal performance was modified. The objective of this investigation was to determine via experimentation, if Al_2O_3 and CuO nanoparticles dispersed in pure MI for mixtures of 1, 2 and 3% (by weight) improved the thermal performance of MI for solar thermal energy systems. Nanoparticles only physically interacted with MI, and not chemically, even after 50 thermal cycles. The distribution of CuO nanoparticles in the nano-PCM was found to be more uniform than alumina nanoparticles. After cycling, nano-MIs studied here suffered a lower decrease in heat of fusion than pure MI, which makes nano-MIs more suitable for solar thermal storage applications at 160–260 °C. Between CuO and Al_2O_3 nanoparticles, latter was found to be more suitable for compact solar thermal energy storage owing to an increase in melting point observed.

  8. PENENTUAN FAKTOR DAN TARAF FAKTOR DALAM PENGENDALIAN KUALITAS PRODUKSI BENANG PCM DI PT APAC INTI CORPORA DENGAN METODE DESAIN EKSPERIMEN

    Directory of Open Access Journals (Sweden)

    Darminto Pujotomo

    2012-02-01

    Full Text Available PT. APAC Inti Corpora merupakan salah satu perusahaan tekstil yang terbesar di Asia Tenggara dimana salah satu jenis produknya adalah benang PCM yang dihasilkan oleh departemen spinning 4. Permasalahan yang muncul adalah produk akhir yang cacat melebihi target perusahaan sebesar 0,8% dari total produksi, sedangkan perusahaan dituntut untuk menghasilkan produk cacat seminimal mungkin. Masalah ini muncul karena masih banyaknya cacat yang timbul pada benang PCM yang didominan oleh cacat crossing (24,67%,  cacat ring cone (21,98%, cacat tanpa ekor (16,02% dan kontaminasi (12,50%. Penelitian ini dimaksudkan untuk melakukan penilaian terhadap proses yang terjadi dan apabila ternyata memang terjadi proses yang tidak terkendali maka selanjutnya akan dilakukan identifikasi dan analisa faktor-faktor yang mempunyai pengaruh secara signifikan terhadap ttimbulnya cacat crossing pada benang PCM. Metode yang digunakan untuk menilai proses operasi adalah metode pengendalian proses statistik (statistical process control, sedangkan metode yang digunakan untuk menganalisa faktor-faktor yang berpengaruh terhadap timbulnya cacat benang PCM adalah metode desain eksperimen faktorial.  Dari grafik pengendali dan penentuan kemampuan proses dapat diketahui bahwa proses operasi yang terjadi berada di luar kontrol karena menghasilkan cukup banyak produk cacat. Faktor-faktor yang akan diteliti dalam penelitian ini adalah faktor ukuran benang, umur mesin dan kecepatan mesin yang masing-masing faktor terdiri dari 2 taraf faktor. Faktor ukuran benang terdiri dari tipis dan tebal. Faktor umur mesin terdiri dari mesin lama dan mesin baru.Faktor kecepatan mesin terdiri dari 900 MPM dan 1000 MPM. Berdasarkaan perhitungan analisa variansi (ANAVA dan test hipotesa, faktor yang signifikan menyebabkan timbulnya cacat crossing adalah faktor ukuran benang  dan umur mesin.   Kata kunci : cacat crossing, pengendalian kualitas, ANAVA   PT.APAC Inti Corpora is the largest textile

  9. Supervisor's accident investigation handbook

    International Nuclear Information System (INIS)

    1980-02-01

    This pamphlet was prepared by the Environmental Health and Safety Department (EH and S) of Lawrence Berkeley Laboratory (LBL) to provide LBL supervisors with a handy reference to LBL's accident investigation program. The publication supplements the Accident and Emergencies section of LBL's Regulations and Procedures Manual, Pub. 201. The present guide discusses only accidents that are to be investigated by the supervisor. These accidents are classified as Type C by the Department of Energy (DOE) and include most occupational injuries and illnesses, government motor-vehicle accidents, and property damages of less than $50,000

  10. Visualization of Traffic Accidents

    Science.gov (United States)

    Wang, Jie; Shen, Yuzhong; Khattak, Asad

    2010-01-01

    Traffic accidents have tremendous impact on society. Annually approximately 6.4 million vehicle accidents are reported by police in the US and nearly half of them result in catastrophic injuries. Visualizations of traffic accidents using geographic information systems (GIS) greatly facilitate handling and analysis of traffic accidents in many aspects. Environmental Systems Research Institute (ESRI), Inc. is the world leader in GIS research and development. ArcGIS, a software package developed by ESRI, has the capabilities to display events associated with a road network, such as accident locations, and pavement quality. But when event locations related to a road network are processed, the existing algorithm used by ArcGIS does not utilize all the information related to the routes of the road network and produces erroneous visualization results of event locations. This software bug causes serious problems for applications in which accurate location information is critical for emergency responses, such as traffic accidents. This paper aims to address this problem and proposes an improved method that utilizes all relevant information of traffic accidents, namely, route number, direction, and mile post, and extracts correct event locations for accurate traffic accident visualization and analysis. The proposed method generates a new shape file for traffic accidents and displays them on top of the existing road network in ArcGIS. Visualization of traffic accidents along Hampton Roads Bridge Tunnel is included to demonstrate the effectiveness of the proposed method.

  11. Experimental and numerical study of heat transfer performance of nitrate/expanded graphite composite PCM for solar energy storage

    International Nuclear Information System (INIS)

    Xiao, X.; Zhang, P.; Li, M.

    2015-01-01

    Highlights: • Thermal conductivity of nitrate/EG composite was accurately measured by considering thermal contact resistance. • Heat storage and retrieval tests were conducted with binary nitrates and nitrates/EG composites. • A comprehensive model was built to interpret the heat transfer characteristics. - Abstract: Eutectic molten salt can be used as the latent thermal energy storage medium in solar energy applications. Nitrates and their binary mixtures are suitable phase change material (PCM) for solar energy applications in middle-temperature-range of 200–300 °C. In the present study, binary nitrate (50 wt.% NaNO_3, 50 wt.% KNO_3) with a melting temperature of about 220 °C was employed as the PCM, and expanded graphite (EG) with the mass fraction of 5%, 10% or 20% was used to enhance the thermal conductivity. The thermal conductivities of pure nitrates and nitrate/EG shape-stabilized composites were measured with a steady-state test rig firstly. Results showed that the addition of EG significantly enhanced the thermal conductivities, e.g., the thermal conductivities of sodium nitrate/20 wt.% EG composite PCM were measured to be 6.66–7.70 W/(m K) in the temperature range of 20–120 °C, indicating about seven times larger than those of pure sodium nitrate. Furthermore, pure binary nitrate and nitrate/EG composite PCM were encapsulated in a cylindrical storage unit with a diameter of 70.0 mm and a length of 280.0 mm. Heat storage and retrieval tests were conducted extensively at different heating temperatures of 250 °C, 260 °C and 270 °C, and different cooling temperatures of 30 °C, 70 °C and 110 °C. Time-durations from temperature evolutions showed that both the melting and solidification processes were accelerated by EG, and the heat transfer characteristics were interpreted by the numerical analysis based on enthalpy–porosity and volume-of-fluid models. The evolution of nitrate/air interface caused by volume expansion ascended gradually

  12. MP2, DFT-D, and PCM study of the HMB-TCNE complex: Thermodynamics, electric properties, and solvent effects

    Science.gov (United States)

    Kysel, Ondrej; Budzák, Scaronimon; Medveď, Miroslav; Mach, Pavel

    Geometry, thermodynamic, and electric properties of the pi-EDA complex between hexamethylbenzene (HMB) and tetracyanoethylene (TCNE) are investigated at the MP2/6-31G* and, partly, DFT-D/6-31G* levels. Solvent effects on the properties are evaluated using the PCM model. Fully optimized HMB-TCNE geometry in gas phase is a stacking complex with an interplanar distance 2.87 × 10-10 m and the corresponding BSSE corrected interaction energy is -51.3 kJ mol-1. As expected, the interplanar distance is much shorter in comparison with HF and DFT results. However the crystal structures of both (HMB)2-TCNE and HMB-TCNE complexes have interplanar distances somewhat larger (3.18 and 3.28 × 10-10 m, respectively) than our MP2 gas phase value. Our estimate of the distance in CCl4 on the basis of PCM solvent effect study is also larger (3.06-3.16 × 10-10 m). The calculated enthalpy, entropy, Gibbs energy, and equilibrium constant of HMB-TCNE complex formation in gas phase are: DeltaH0 = -61.59 kJ mol-1, DeltaSc0 = -143 J mol-1 K-1, DeltaG0 = -18.97 kJ mol-1, and K = 2,100 dm3 mol-1. Experimental data, however, measured in CCl4 are significantly lower: DeltaH0 = -34 kJ mol-1, DeltaSc0 = -70.4 J mol-1 K-1, DeltaG0 = -13.01 kJ mol-1, and K = 190 dm3 mol-1. The differences are caused by solvation effects which stabilize more the isolated components than the complex. The total solvent destabilization of Gibbs energy of the complex relatively to that of components is equal to 5.9 kJ mol-1 which is very close to our PCM value 6.5 kJ mol-1. MP2/6-31G* dipole moment and polarizabilities are in reasonable agreement with experiment (3.56 D versus 2.8 D for dipole moment). The difference here is due to solvent effect which enlarges interplanar distance and thus decreases dipole moment value. The MP2/6-31G* study supplemented by DFT-D parameterization for enthalpy calculation, and by the PCM approach to include solvent effect seems to be proper tools to elucidate the properties of pi

  13. The Chernobyl accident consequences

    International Nuclear Information System (INIS)

    2001-04-01

    Five teen years later, Tchernobyl remains the symbol of the greater industrial nuclear accident. To take stock on this accident, this paper proposes a chronology of the events and presents the opinion of many international and national organizations. It provides also web sites references concerning the environmental and sanitary consequences of the Tchernobyl accident, the economic actions and propositions for the nuclear safety improvement in the East Europe. (A.L.B.)

  14. Radiation, accidents, society

    International Nuclear Information System (INIS)

    1988-01-01

    This book is meant to be used as a reference book for information officers at the event of a nuclear accident. The main part is edited in alphabetical order to facilitate use under stress. The book gives a short review of the health risks of radiation, and descriptions of accidents that have occured. The index words that have been chosen for the main part of the book have been selected due to experiences in connection with incidents and accidents. (L.E.)

  15. Reactivity insertion accident analysis

    International Nuclear Information System (INIS)

    Moreira, J.M.L.; Nakata, H.; Yorihaz, H.

    1990-04-01

    The correct prediction of postulated accidents is the fundamental requirement for the reactor licensing procedures. Accident sequences and severity of their consequences depend upon the analysis which rely on analytical tools which must be validated against known experimental results. Present work presents a systematic approach to analyse and estimate the reactivity insertion accident sequences. The methodology is based on the CINETHICA code which solves the point-kinetics/thermohydraulic coupled equations with weighted temperature feedback. Comparison against SPERT experimental results shows good agreement for the step insertion accidents. (author) [pt

  16. Nuclear accidents and epidemiology

    International Nuclear Information System (INIS)

    1987-01-01

    A consultation on epidemiology related to the Chernobyl accident was held in Copenhagen in May 1987 as a basis for concerted action. This was followed by a joint IAEA/WHO workshop in Vienna, which reviewed appropriate methodologies for possible long-term effects of radiation following nuclear accidents. The reports of these two meetings are included in this volume, and cover the subjects: 1) Epidemiology related to the Chernobyl nuclear accident. 2) Appropriate methodologies for studying possible long-term effects of radiation on individuals exposed in a nuclear accident. Figs and tabs

  17. Accidents (FARS) (National)

    Data.gov (United States)

    Department of Transportation — Accident - (1975-current): This data file (NTAD) contains information about crash characteristics and environmental conditions at the time of the crash. There is one...

  18. CoSyPCM - Solar combisystem with phase change materials - Annual report 2005; CoSyPCM - Combi-systeme avec materiaux a changement de phase. Rapport annuel 2005

    Energy Technology Data Exchange (ETDEWEB)

    Citherlet, S.; Bony, J.

    2005-12-15

    Computerized simulations have been performed to validate an improved mathematical model of the storage tank of solar heating systems for domestic hot water preparation and space heating ('solar combisystems'). Heat is stored in water and in various phase change materials (PCM) immersed in the storage tank. The improvements implemented in the model are described. The validation was performed by comparison with measured data. The dynamics of the fusion and solidification of the PCMs have been measured and simulated. The following materials have been studied: paraffin; paraffin with aluminium shavings; paraffin with aluminium honeycomb; sodium acetate with graphite. The measured data for the first two materials were obtained from the own laboratory of the University of Applied Sciences of Western Switzerland, in Yverdon-les-Bains. The measured data for the last two materials were obtained respectively from the University of Lleida, Spain and the University of Graz, Austria. The samples were contained in spherical or cylindrical containers. One important conclusion is that the convection flow in the liquid phase of the PCM cannot be neglected in the mathematical model.

  19. Experimental investigation of the dynamic behavior of a large-scale refrigeration – PCM energy storage system. Validation of a complete model

    International Nuclear Information System (INIS)

    Wu, Jing; Tremeac, Brice; Terrier, Marie-France; Charni, Mehdi; Gagnière, Emilie; Couenne, Françoise; Hamroun, Boussad; Jallut, Christian

    2016-01-01

    In the area of buildings refrigeration, the use of thermal energy storages coupled with heat pumps is a significant way for reducing the operating costs and optimizing the design of equipment. In this paper, a prototype of large-scale refrigeration - PCM (Phase Change Material) energy storage system is described, from which experimental results on transient behavior are obtained. A dynamic model for transient simulation of the coupled system is presented. The fluid flows through the heat exchangers and the storage tank are represented by a cascade of Continuous Stirred Tank Reactors (CSTRs). Switching procedures between different model configurations associated to phase transitions within heat exchangers and PCM storage tank are mathematically performed by matrix operations. The compressor, the expansion valve and the pressure drop across the evaporator are represented by static models based on empirical correlations. A PI controller for the expansion valve opening is integrated in the heat pump model to maintain the superheat at evaporator exit. The model is validated by a complete and detailed comparison between simulation and experimental results. - Highlights: • Experimental investigation of a refrigeration-PCM storage system is presented. • A detailed dynamic model for the coupled system is proposed. • Fluid flows in heat exchangers and PCM storage are represented by a cascade of CSTRs. • Phase transitions events according to time and space within heat exchangers and PCM storage are considered in the model. • Complete comparisons between experimental and simulation results are carried out.

  20. Study of heat transfer and pressure drop characteristics of air heat exchanger using PCM for free cooling applications

    Directory of Open Access Journals (Sweden)

    Kalaiselvam Sivakumar

    2016-01-01

    Full Text Available Free cooling is the process of storing the cool energy available in the night ambient air and using it during the day. The heat exchanger used in this work is a modular type which is similar to the shell and tube heat exchanger. The shell side is filled with Phase Change Materials (PCM and air flow is through the tubes in the module. The modules of the heat exchanger are arranged one over other with air spacers in between each module. The air space provided in between the module in-creases the retention time of the air for better heat transfer. Transient Computational Fluid Dynamics modeling is carried out for single air passage in a modular heat exchanger. It shows that the PCM phase transition time in the module in which different shape of fins is adopted. The module with rectangular fins has 17.2 % reduction in solidification compared with the plain module. Then steady state numerical analysis is accomplished to the whole module having the fin of high heat transfer, so that pressure drop, flow and thermal characteristics across the module and the air spacers are deter-mined for various air inlet velocities of 0.4 to 1.6 m/s. To validate the computational results, experiments are carried out and the agreement was found to be good.

  1. Study of the Thermal Properties and the Fire Performance of Flame Retardant-Organic PCM in Bulk Form.

    Science.gov (United States)

    Palacios, Anabel; De Gracia, Alvaro; Haurie, Laia; Cabeza, Luisa F; Fernández, A Inés; Barreneche, Camila

    2018-01-12

    The implementation of organic phase change materials (PCMs) in several applications such as heating and cooling or building comfort is an important target in thermal energy storage (TES). However, one of the major drawbacks of organic PCMs implementation is flammability. The addition of flame retardants to PCMs or shape-stabilized PCMs is one of the approaches to address this problem and improve their final deployment in the building material sector. In this study, the most common organic PCM, Paraffin RT-21, and fatty acids mixtures of capric acid (CA), myristic acid (MA), and palmitic acid (PA) in bulk, were tested to improve their fire reaction. Several flame retardants, such as ammonium phosphate, melamine phosphate, hydromagnesite, magnesium hydroxide, and aluminum hydroxide, were tested. The properties of the improved PCM with flame retardants were characterized by thermogravimetric analyses (TGA), the dripping test, and differential scanning calorimetry (DSC). The results for the dripping test show that fire retardancy was considerably enhanced by the addition of hydromagnesite (50 wt %) and magnesium hydroxide (50 wt %) in fatty acids mixtures. This will help the final implementation of these enhanced PCMs in building sector. The influence of the addition of flame retardants on the melting enthalpy and temperatures of PCMs has been evaluated.

  2. Study of the Thermal Properties and the Fire Performance of Flame Retardant-Organic PCM in Bulk Form

    Directory of Open Access Journals (Sweden)

    Anabel Palacios

    2018-01-01

    Full Text Available The implementation of organic phase change materials (PCMs in several applications such as heating and cooling or building comfort is an important target in thermal energy storage (TES. However, one of the major drawbacks of organic PCMs implementation is flammability. The addition of flame retardants to PCMs or shape-stabilized PCMs is one of the approaches to address this problem and improve their final deployment in the building material sector. In this study, the most common organic PCM, Paraffin RT-21, and fatty acids mixtures of capric acid (CA, myristic acid (MA, and palmitic acid (PA in bulk, were tested to improve their fire reaction. Several flame retardants, such as ammonium phosphate, melamine phosphate, hydromagnesite, magnesium hydroxide, and aluminum hydroxide, were tested. The properties of the improved PCM with flame retardants were characterized by thermogravimetric analyses (TGA, the dripping test, and differential scanning calorimetry (DSC. The results for the dripping test show that fire retardancy was considerably enhanced by the addition of hydromagnesite (50 wt % and magnesium hydroxide (50 wt % in fatty acids mixtures. This will help the final implementation of these enhanced PCMs in building sector. The influence of the addition of flame retardants on the melting enthalpy and temperatures of PCMs has been evaluated.

  3. Study of the Thermal Properties and the Fire Performance of Flame Retardant-Organic PCM in Bulk Form

    Science.gov (United States)

    Palacios, Anabel; De Gracia, Alvaro

    2018-01-01

    The implementation of organic phase change materials (PCMs) in several applications such as heating and cooling or building comfort is an important target in thermal energy storage (TES). However, one of the major drawbacks of organic PCMs implementation is flammability. The addition of flame retardants to PCMs or shape-stabilized PCMs is one of the approaches to address this problem and improve their final deployment in the building material sector. In this study, the most common organic PCM, Paraffin RT-21, and fatty acids mixtures of capric acid (CA), myristic acid (MA), and palmitic acid (PA) in bulk, were tested to improve their fire reaction. Several flame retardants, such as ammonium phosphate, melamine phosphate, hydromagnesite, magnesium hydroxide, and aluminum hydroxide, were tested. The properties of the improved PCM with flame retardants were characterized by thermogravimetric analyses (TGA), the dripping test, and differential scanning calorimetry (DSC). The results for the dripping test show that fire retardancy was considerably enhanced by the addition of hydromagnesite (50 wt %) and magnesium hydroxide (50 wt %) in fatty acids mixtures. This will help the final implementation of these enhanced PCMs in building sector. The influence of the addition of flame retardants on the melting enthalpy and temperatures of PCMs has been evaluated. PMID:29329212

  4. Experimental investigation of the charge/discharge process for an organic PCM macroencapsulated in an aluminium rectangular cavity

    Science.gov (United States)

    Bejan, Andrei-Stelian; Labihi, Abdelouhab; Croitoru, Cristiana Verona; Catalina, Tiberiu; Chehouani, Hassan; Benhamou, Brahim

    2018-02-01

    Buildings sector has one of the highest potential regarding the reduction of greenhouse gases emissions, as being responsible for more than 40% of energy consumption worldwide. This is why, in order to achieve indoor thermal comfort, it is mandatory to use energy-efficient systems. Materials acting as thermal energy storage (TES) represents one of the most effective strategy that can be implemented and nowadays, many studies are focusing their attention on latent heat storage, respectively on phase changing materials (PCM) which can embed a large embed a high quantity of energy, unlike classic materials acting as thermal mass. This purpose of this paper is to experimentally investigate the charge and discharge processes for an organic PCM (RT35 paraffin) macroencapsulated in an aluminium rectangular cavity which was placed first in a horizontal position and after in a vertical position. After several experimental campaigns conducted we determined that the vertical position enhance the heat transfer because of the natural convection which occurs inside the cavity. Therefore, the charging time is lower in case of the vertical cavity and the temperature measured inside and on the surface is higher.

  5. Effect of the inter-block spacing on the thermal performance of a PCM based heat sink

    Energy Technology Data Exchange (ETDEWEB)

    Faraji, M.; El Qarnia, H. [Cadi Ayyad Univ., Marrakech (Morocco). Faculte des sciences Semlalia, Dept. de physique, Laboratoire de mecanique des fluides et d' energetique; El Khadir, L. [Cadi Ayyad Univ., Marrakech (Morocco). Faculte des sciences Semlalia, Dept. de physique, Laboratoire d' tomatique de l' Environnement et Procedes de Transferts

    2010-07-01

    Advanced electronic devices require efficient thermal control systems. Heat transfer analysis of such systems is challenging because of constraints regarding space limitations, power consumption and noise level. This study considered the problem of melting and natural convection in a rectangular enclosure heated with 3 heat sources with a constant and uniform volumetric heat generation. The heat sources were protruding and mounted on a vertical conducting plate. Conjugate conduction in a plate and heat sources coupled with natural convection and melting process were examined in an effort to determine the effects of the inter-blocks spacing ratio on the thermal performance of the cooling PCM-heat sink. The percentage contribution of substrate heat conduction on the total removed heat from heat sources was also investigated. Correlations were derived for the non- dimensional secured working time and the corresponding melt fraction. In order to investigate the thermal behaviour of the proposed heat sink, a mathematical model was developed based on the mass, momentum and energy conservation equations. The results revealed that for lower inter-blocks spacing, the dimensionless secured working time needed by the chips to reach the critical temperature was maximized. The highest inter-blocks spacing ratio provoked a sudden rise in chip temperatures and thus reduced the dimensionless secured working time. It was concluded that this approach can be used in the design of PCM-based cooling systems. 9 refs., 2 tabs., 4 figs.

  6. Domino effect in chemical accidents: main features and accident sequences

    OpenAIRE

    Casal Fàbrega, Joaquim; Darbra Roman, Rosa Maria

    2010-01-01

    The main features of domino accidents in process/storage plants and in the transportation of hazardous materials were studied through an analysis of 225 accidents involving this effect. Data on these accidents, which occurred after 1961, were taken from several sources. Aspects analyzed included the accident scenario, the type of accident, the materials involved, the causes and consequences and the most common accident sequences. The analysis showed that the most frequent causes a...

  7. Chernobyl accident and Denmark

    International Nuclear Information System (INIS)

    1986-12-01

    The report describes the Chernobyl accident and its consequences for Denmark in particular. It was commissioned by The Secretary of State for the Environment. Volume 2 contains copies of original documents issued by Danish authorities during the first accident phase and afterwards. Evaluations, monitoring data, press releases, legislation acts etc. are included. (author)

  8. Criticality accident in Argentina

    International Nuclear Information System (INIS)

    Oliveira, A.R. de.

    1984-01-01

    A recent criticality type accident, ocurred in Argetina, is commented. Considerations about the nature of the facility where this accident took place, its genesis, type of operation carried out on the day of the event, and the medical aspects involved are done. (Author) [pt

  9. Chernobyl accident and Danmark

    International Nuclear Information System (INIS)

    1986-12-01

    The report describes the Chernobyl accident and its consequences for Denmark in particular. It was commissioned by the Secretary of State for the Environment. Volume 1 contains copies of original documents issued by Danish authorities during the first accident phase and afterwards. Evaluations, monitoring data, press releases, legislation acts etc. are included. (author)

  10. Communication and industrial accidents

    NARCIS (Netherlands)

    As, Sicco van

    2001-01-01

    This paper deals with the influence of organizational communication on safety. Accidents are actually caused by individual mistakes. However the underlying causes of accidents are often organizational. As a link between these two levels - the organizational failures and mistakes - I suggest the

  11. Chapter 6: Accidents

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2018-04-01

    Th chapter 6 presents the accidents of: 1) Stimos (Italy - May, 1975); 2) San Salvador (El Salvador - February 5, 1989); 3) Soreq (Israel - June 21, 1990); 4) Nesvizh (Belarus - October 26, 1991); 5) Illinois (USA - February, 1965); 6)Maryland (EUA - December 11, 1991); 7)Hanoi (Vietnam -November 17, 1992); 8)Fleurus (Belgium - March 11, 2006) and final remarks on accidents.

  12. Radiological accidents in medical practice

    International Nuclear Information System (INIS)

    Cardenas Herrera, Juan

    2012-01-01

    Different radiological accidents that may occur in medical practice are shown. The following topics are focused: accident statistics for medical exposure, accidental medical exposures, radiotherapy accidents and potential accidental scenarios [es

  13. [Accidents and injuries at work].

    Science.gov (United States)

    Standke, W

    2014-06-01

    In the case of an accident at work, the person concerned is insured by law according to the guidelines of the Sozialgesetzbuch VII as far as the injuries have been caused by this accident. The most important source of information on the incident in question is the accident report that has to be sent to the responsible institution for statutory accident insurance and prevention by the employer, if the accident of the injured person is fatal or leads to an incapacity to work for more than 3 days (= reportable accident). Data concerning accidents like these are sent to the Deutsche Gesetzliche Unfallversicherung (DGUV) as part of a random sample survey by the institutions for statutory accident insurance and prevention and are analyzed statistically. Thus the key issues of accidents can be established and used for effective prevention. Although the success of effective accident prevention is undisputed, there were still 919,025 occupational accidents in 2011, with clear gender-related differences. Most occupational accidents involve the upper and lower extremities. Accidents are analyzed comprehensively and the results are published and made available to all interested parties in an effort to improve public awareness of possible accidents. Apart from reportable accidents, data on the new occupational accident pensions are also gathered and analyzed statistically. Thus, additional information is gained on accidents with extremely serious consequences and partly permanent injuries for the accident victims.

  14. Database on aircraft accidents

    International Nuclear Information System (INIS)

    Nishio, Masahide; Koriyama, Tamio

    2012-09-01

    The Reactor Safety Subcommittee in the Nuclear Safety and Preservation Committee published the report 'The criteria on assessment of probability of aircraft crash into light water reactor facilities' as the standard method for evaluating probability of aircraft crash into nuclear reactor facilities in July 2002. In response to the report, Japan Nuclear Energy Safety Organization has been collecting open information on aircraft accidents of commercial airplanes, self-defense force (SDF) airplanes and US force airplanes every year since 2003, sorting out them and developing the database of aircraft accidents for latest 20 years to evaluate probability of aircraft crash into nuclear reactor facilities. This year, the database was revised by adding aircraft accidents in 2010 to the existing database and deleting aircraft accidents in 1991 from it, resulting in development of the revised 2011 database for latest 20 years from 1991 to 2010. Furthermore, the flight information on commercial aircrafts was also collected to develop the flight database for latest 20 years from 1991 to 2010 to evaluate probability of aircraft crash into reactor facilities. The method for developing the database of aircraft accidents to evaluate probability of aircraft crash into reactor facilities is based on the report 'The criteria on assessment of probability of aircraft crash into light water reactor facilities' described above. The 2011 revised database for latest 20 years from 1991 to 2010 shows the followings. The trend of the 2011 database changes little as compared to the last year's one. (1) The data of commercial aircraft accidents is based on 'Aircraft accident investigation reports of Japan transport safety board' of Ministry of Land, Infrastructure, Transport and Tourism. 4 large fixed-wing aircraft accidents, 58 small fixed-wing aircraft accidents, 5 large bladed aircraft accidents and 114 small bladed aircraft accidents occurred. The relevant accidents for evaluating

  15. Management of severe accidents

    International Nuclear Information System (INIS)

    Jankowski, M.W.

    1987-01-01

    The definition and the multidimensionality aspects of accident management have been reviewed. The suggested elements in the development of a programme for severe accident management have been identified and discussed. The strategies concentrate on the two tiered approaches. Operative management utilizes the plant's equipment and operators capabilities. The recovery managment concevtrates on preserving the containment, or delaying its failure, inhibiting the release, and on strategies once there has been a release. The inspiration for this paper was an excellent overview report on perspectives on managing severe accidents in commercial nuclear power plants and extending plant operating procedures into the severe accident regime; and by the most recent publication of the International Nuclear Safety Advisory Group (INSAG) considering the question of risk reduction and source term reduction through accident prevention, management and mitigation. The latter document concludes that 'active development of accident management measures by plant personnel can lead to very large reductions in source terms and risk', and goes further in considering and formulating the key issue: 'The most fruitful path to follow in reducing risk even further is through the planning of accident management.' (author)

  16. Accidents with sulfuric acid

    Directory of Open Access Journals (Sweden)

    Rajković Miloš B.

    2006-01-01

    Full Text Available Sulfuric acid is an important industrial and strategic raw material, the production of which is developing on all continents, in many factories in the world and with an annual production of over 160 million tons. On the other hand, the production, transport and usage are very dangerous and demand measures of precaution because the consequences could be catastrophic, and not only at the local level where the accident would happen. Accidents that have been publicly recorded during the last eighteen years (from 1988 till the beginning of 2006 are analyzed in this paper. It is very alarming data that, according to all the recorded accidents, over 1.6 million tons of sulfuric acid were exuded. Although water transport is the safest (only 16.38% of the total amount of accidents in that way 98.88% of the total amount of sulfuric acid was exuded into the environment. Human factor was the common factor in all the accidents, whether there was enough control of the production process, of reservoirs or transportation tanks or the transport was done by inadequate (old tanks, or the accidents arose from human factor (inadequate speed, lock of caution etc. The fact is that huge energy, sacrifice and courage were involved in the recovery from accidents where rescue teams and fire brigades showed great courage to prevent real environmental catastrophes and very often they lost their lives during the events. So, the phrase that sulfuric acid is a real "environmental bomb" has become clearer.

  17. Management of severe accidents

    International Nuclear Information System (INIS)

    Jankowski, M.W.

    1988-01-01

    The definition and the multidimensionality aspects of accident management have been reviewed. The suggested elements in the development of a programme for severe accident management have been identified and discussed. The strategies concentrate on the two tiered approaches. Operative management utilizes the plant's equipment and operators capabilities. The recovery management concentrates on preserving the containment, or delaying its failure, inhibiting the release, and on strategies once there has been a release. The inspiration for this paper was an excellent overview report on perspectives on managing severe accidents in commercial nuclear power plants and extending plant operating procedures into the severe accident regime; and by the most recent publication of the International Nuclear Safety Advisory Group (INSAG) considering the question of risk reduction and source term reduction through accident prevention, management and mitigation. The latter document concludes that active development of accident management measures by plant personnel can lead to very large reductions in source terms and risk, and goes further in considering and formulating the key issue: The most fruitful path to follow in reducing risk even further is through the planning of accident management

  18. Persistence of airline accidents.

    Science.gov (United States)

    Barros, Carlos Pestana; Faria, Joao Ricardo; Gil-Alana, Luis Alberiko

    2010-10-01

    This paper expands on air travel accident research by examining the relationship between air travel accidents and airline traffic or volume in the period from 1927-2006. The theoretical model is based on a representative airline company that aims to maximise its profits, and it utilises a fractional integration approach in order to determine whether there is a persistent pattern over time with respect to air accidents and air traffic. Furthermore, the paper analyses how airline accidents are related to traffic using a fractional cointegration approach. It finds that airline accidents are persistent and that a (non-stationary) fractional cointegration relationship exists between total airline accidents and airline passengers, airline miles and airline revenues, with shocks that affect the long-run equilibrium disappearing in the very long term. Moreover, this relation is negative, which might be due to the fact that air travel is becoming safer and there is greater competition in the airline industry. Policy implications are derived for countering accident events, based on competition and regulation. © 2010 The Author(s). Journal compilation © Overseas Development Institute, 2010.

  19. Analysis of the rod drop accident for Angra-1

    International Nuclear Information System (INIS)

    Veloso, M.A.; Atayde, P.A.

    1989-01-01

    The aim of this work is to present a rod drop accident analysis for the third cycle of the Angra-1 nuclear power plant operating in the automatic control mode. In this analysis all possible configurations for dropped rods caused by a single failure in the controller circuits have been considered. The dropped rod worths, power distributions and excore detector tilts were determined by using the Siemens/KWU neutronic code system, in particular the MEDIUM2, PINPOW and DETILT codes. The transient behaviour of the plant during the rod drop event was simulated with the SACI2/MOD0 code, developed at CDTN. Determinations related to the DNBR design limit were conducted by utilizing the CDTN PANTERA-1P subchannel code. The transient analysis indicated that for dropped rod worths greater than about 425 pcm reactor trip from negative neutron flux rate will take place independently of core conditions. In the range from 0 to 425 pcm large power overshoots may occur as a consequence of the automatic control system action. The magnitude of the maximum power peaking during the event increases with the dropped rod worth, as far as the control bank is able to compensate the initial reactivity decrease. Thermal-hydraulic evaluations carried out with the PANTERA-1P code show that for all the relevant dropped rod worths the minimum DNBR will remain above a limit value of 1.365. Even if this conservative limit is met, the calculated nuclear power peaking factors, F N AH , will be at least 6% higher than the allowable F N AH -values. Therefore, the DNBR design margin will be preserved at the event of rod drop. (author)

  20. Market penetration of intersection AEB: Characterizing avoided and residual straight crossing path accidents.

    Science.gov (United States)

    Sander, Ulrich; Lubbe, Nils

    2018-06-01

    Car occupants account for one third of all junction fatalities in the European Union. Driver warning can reduce intersection accidents by up to 50 percent; adding Autonomous Emergency Braking (AEB) delivers a reduction of up to 70 percent. However, these findings are based on an assumed 100 percent equipment rate, which may take decades to achieve. Our study investigates the relationship between intersection AEB market penetration rates and avoidance of accidents and injuries in order to guide implementation strategies. Additionally, residual accident characteristics (impact configurations and severity) are analyzed to provide a basis for future in-crash protection requirements. We determined which accidents would have been avoided through the use of an Intersection AEB system with different sensor field-of-views (180° and 120°) by means of re-simulating the pre-crash phase of 792 straight crossing path (SCP) car-to-car accidents recorded in the German In-Depth Accident Study (GIDAS) and the associated Pre-Crash Matrix (PCM). Intersection AEB was activated when neither of the conflict opponents could avoid the crash through reasonable braking or steering reactions. For not-avoided accidents, we used the Kudlich-Slibar rigid body impulse model to calculate the change of velocity during the impact as a measure of impact severity and the principal direction of force. Accident avoidance over market penetration is not linear but exponential, with higher gains at low penetration rates and lower gains at higher rates. A wide field-of-view sensor (180°) substantially increased accident avoidance and injury mitigation rates compared to a 120° field-of-view sensor. For a 180° field-of-view sensor at 100 percent market penetration, about 80 percent of the accidents and 90 percent of the MAIS2 + F injuries could be avoided. For the remaining accidents, AEB intervention rarely affected side of impact. The median change of velocity (delta-V) of the remaining crashes

  1. Social impact of accidents

    International Nuclear Information System (INIS)

    Kuroda, Isao

    1997-01-01

    There is the quite big difference between technological risk and social risk feeling. Various biases of social and sensational factors on accidents must be considered to recognize this difference. 'How safe is safe enough' is the perpetual thema concerning with not only technology but also sociology. The safety goal in aircraft design and how making effort to improve the present safety status in civil jet aircrafts is discussed as an example of social risk allowance. INSAG under IAEA started to discuss the safety culture after Chernobyl nuclear power plant accident on 1986. Safety culture and risk communication are the most important procedures to relieve the social impact for accidents. (author)

  2. Severe accident behavior

    International Nuclear Information System (INIS)

    Denning, R.S.

    1986-01-01

    The purpose of this paper is to provide an overview of severe accident behavior. The term source term is defined and a brief history of the regulatory use of source term is presented. The processes in severe accidents in light water reactors are described with particular emphasis on the relationships between accident thermal-hydraulics and chemistry. Those factors which have the greatest impact on predicted source terms are identified. Design differences between plants that affect source term estimation are also described. The principal unresolved issues are identified that are the focus of ongoing research and debate in the technical community

  3. Management of accident risks

    International Nuclear Information System (INIS)

    Compes, P.C.

    1987-01-01

    The example of the Chernobyl accident and the statistics of the occurrence of accidents make clear the threat to humanity, if one cannot guarantee successful accident prevention in the use and distribution of the projects aimed at. The science of safety, as it is known in the Wuppertal model, makes its contribution to this vital task for the human community. It makes it necessary to create the essential dates and concepts, the methods, principles and techniques based on them and the associated instrumentation. (DG) [de

  4. Chernobyl accident and Denmark

    International Nuclear Information System (INIS)

    1986-12-01

    The report describes the Chernobyl accident and its consequences for Denmark in particular. It was commissioned by The Secretary of State for the Environment. The event at the accident site, the release and dispersal of radioactive substances into the atmosphere and over Europe, is described. A discussion of the Danish organisation for nuclear emergencies, how it was activated and adapted to the actual situation, is given. A comprehensive description of the radiological contamination in Denmark following the accident and the estimated health effects, is presented. The situation in other European countries is mentioned. (author)

  5. Technical basis for implementing the use of the PCM-1B for personnel releases at tank farms

    International Nuclear Information System (INIS)

    Brown, R.L.

    1996-01-01

    Currently, Tanks Farms Transition Projects require personnel to perform a whole body survey with portable survey instrumentation prior to entering an automated counting system capable of performing a whole body survey. This practice is redundant since automated whole body survey devices are, in most cases, more sensitive and are less likely to be used incorrectly than portable instrumentation. Additionally, Article 221.2 of the Hanford Site Radiological Control Manual (HSRCM-1) states ''Monitoring for contamination should be performed using frisking equipment that under laboratory conditions can detect total contamination of at least the values specified in Table 2-2.'' Based on this criteria implementing the use of an automated whole body survey device would save significant time, money and reduce the current crowding and potential loss of contamination control that now occurs during peak times at step off pads. This document describes implementation process for applying PCM-1B instruments to perform personnel release surveys

  6. Parametric analysis of the operation of nocturnal radiative cooling panels coupled with in room PCM ceiling panels

    DEFF Research Database (Denmark)

    Bourdakis, Eleftherios; Kazanci, Ongun Berk; Péan, T.Q.

    2017-01-01

    03:00 and get activated when the temperature in the storage tank was below 21°C, 69.8°F, activate the heat pump no earlier than 05:00 and get activated when the temperature in the storage tank was below 15°C, 59°F, and lastly have a temperature difference between the output of the solar panels......The scope of this parametric simulation study was to identify the optimal combination of set-points for different parameters of a radiant PCM ceiling panels cooling system that will result in the best indoor thermal environment with the least possible energy use. The results showed that for each...

  7. Thermal energy storage in the form of heat or cold with using of the PCM-based accumulation panels

    Directory of Open Access Journals (Sweden)

    Skovajsa Jan

    2016-01-01

    Full Text Available This article describes the usage of thermal energy storage in the form of heat and cold with an adaptation of the special device which is composed of the thermal panels. These panels are based on the phase change materials (PCM for normal inner environment temperature in buildings. The energy for the thermal energy storage is possible to get from built-in electric heating foil or from the tube heat exchanger, which is build in the thermal panels. This technology is able to use renewable energy sources, for example, solar thermal collectors and air-to-water heat pump as a source of heat for heating of the hot water tank. In the cooling mode, there is able to use the heat pump or photovoltaics panels in combination with thermoelectric coolers for cooling.

  8. Data demonstrating the influence of the latent storage efficiency on the dynamic thermal characteristics of a PCM layer

    Directory of Open Access Journals (Sweden)

    D. Mazzeo

    2017-06-01

    Full Text Available Dynamic thermal characteristics, for each month of the year, of PCM layers with different melting temperatures and thermophysical properties, in a steady periodic regime, were determined (Mazzeo et al., 2017 [1]. The layer is subjected to climatic conditions characterizing two locations, one with a continental climate and the second one with a Mediterranean climate. This data article provides detailed numerical data, as a function of the latent storage efficiency, including monthly average daily values: of the latent energy fraction, of the decrement factors of the temperature, of the heat flux and of the energy, and of the time lags of the maximum and minimum peaks of the temperature and of the heat flux.

  9. Accident resistant transport container

    Science.gov (United States)

    Anderson, J.A.; Cole, K.K.

    The invention relates to a container for the safe air transport of plutonium having several intermediate wood layers and a load spreader intermediate an inner container and an outer shell for mitigation of shock during a hypothetical accident.

  10. Accident resistant transport container

    International Nuclear Information System (INIS)

    Andersen, J.A.; Cole, J.K.

    1980-01-01

    The invention relates to a container for the safe air transport of plutonium having several intermediate wood layers and a load spreader intermediate an inner container and an outer shell for mitigation of shock during a hypothetical accident

  11. Big nuclear accidents

    International Nuclear Information System (INIS)

    Marshall, W.; Billingon, D.E.; Cameron, R.F.; Curl, S.J.

    1983-09-01

    Much of the debate on the safety of nuclear power focuses on the large number of fatalities that could, in theory, be caused by extremely unlikely but just imaginable reactor accidents. This, along with the nuclear industry's inappropriate use of vocabulary during public debate, has given the general public a distorted impression of the risks of nuclear power. The paper reviews the way in which the probability and consequences of big nuclear accidents have been presented in the past and makes recommendations for the future, including the presentation of the long-term consequences of such accidents in terms of 'loss of life expectancy', 'increased chance of fatal cancer' and 'equivalent pattern of compulsory cigarette smoking'. The paper presents mathematical arguments, which show the derivation and validity of the proposed methods of presenting the consequences of imaginable big nuclear accidents. (author)

  12. Accidents in perspective

    International Nuclear Information System (INIS)

    Gittus, J.H.

    1989-01-01

    The nuclear industry perspective and the public perspective on big nuclear accidents and leukaemia near nuclear sites are discussed. The industry perspective is that big accidents are so unlikely as to be virtually impossible and that leukaemia is not specifically associated with nuclear installations. Clusters of cancer with statistical significance occur in major cities. The public perspective is coloured by a prejudice and myth: the fear of radiation. The big nuclear accident is seen therefore as much more unacceptable than any other big accident. Risks associated with Sizewell-B nuclear station and the liquid gas depot at Canvey Island are discussed. The facts and figures are presented as tables and graphs. Given conflicting interpretations of the leukaemia problem the public inclines towards the more pessimistic view. (author)

  13. Boating Accident Statistics

    Data.gov (United States)

    Department of Homeland Security — Accident statistics available on the Coast Guard’s website by state, year, and one variable to obtain tables and/or graphs. Data from reports has been loaded for...

  14. Thermal performance analysis of PCM in refrigerated container envelopes in the Italian context – Numerical modeling and validation

    International Nuclear Information System (INIS)

    Copertaro, Benedetta; Principi, Paolo; Fioretti, Roberto

    2016-01-01

    Highlights: • A refrigerated container with PCMs was evaluated in the Italian climatic context. • The numerical results were validated by an experimental campaign. • A 4.23% of mean bias was achieved comparing the numerical and experimental results. • PCMs application leads to a reduction in peak heat load of 20%. • An energy rate reduction of 4.65% was obtained in the PCMs added container. - Abstract: Due to external climatic conditions, radiation and temperature, refrigerated containers are subjected to high thermal stresses during storage in yards, warehouses, ships or during transport by rail or road. Moreover the consequent high thermal load has a great influence on both the electric and fuel energy consumption and on combined greenhouse gas emissions into the atmosphere. The aim of this research is the theoretical evaluation, using a previously validated Finite Element Method (FEM), of the related energy benefits deriving from the application of PCMs (Phase Change Materials) to a traditional refrigerated container envelope. Specifically the numerical analysis was performed for several kinds of PCMs, climatic conditions and exposures. The study also provides a numerical tool to be used in the prediction of the thermal performance of refrigerated container envelopes with PCM in the Italian context. An experimental analysis was carried out in order to test the accuracy of the numerical model and to validate it. Results show that PCM application to a 20’ ISO container envelope can reduce and shift the daily heat load phases with respect to a traditional envelope fitted only with insulating materials.

  15. Occupational Accidents And Preventive Measures

    CERN Document Server

    Fassnacht, V

    2006-01-01

    This report presents the 2005 statistics concerning occupational accidents involving members of the CERN personnel and contractors' personnel. It sets out the accident frequency and severity rates and provides a breakdown of accidents by cause and injury. It also contains a summary analysis of the most serious accidents and the associated recommendations.

  16. Accidents with sulfuric acid

    OpenAIRE

    Rajković Miloš B.

    2006-01-01

    Sulfuric acid is an important industrial and strategic raw material, the production of which is developing on all continents, in many factories in the world and with an annual production of over 160 million tons. On the other hand, the production, transport and usage are very dangerous and demand measures of precaution because the consequences could be catastrophic, and not only at the local level where the accident would happen. Accidents that have been publicly recorded during the last eigh...

  17. The Chernobyl accident

    International Nuclear Information System (INIS)

    Berg, J.O.; Christensen, G.; Lingjaerde, R.; Smidt Olsen, H.; Wethe, P.I.

    1986-10-01

    In connection with the Chernobyl accident the report gives a description of the technical features of importance to the accident, the course of events, and the estimated health hazards in the local environment. Dissimilarities in western and Sovjet reactor safety philosophy are dealt with, as well as conceivable concequences in relation to technology and research in western nuclear power programmes. Results of activity level measurements of air and foodstuff, made in Norway by Institute for Energy Technology, are given

  18. Accident and emergency management

    International Nuclear Information System (INIS)

    Andersen, V.; Moellenbach, K.; Heinonen, R.; Jakobsson, S.; Kukko, T.; Berg, Oe.; Larsen, J.S.; Westgaard, T.; Magnusson, B.; Andersson, H.; Holmstroem, C.; Brehmer, B.; Allard, R.

    1988-06-01

    There is an increasing potential for severe accidents as the industrial development tends towards large, centralised production units. In several industries this has led to the formation of large organisations which are prepared for accidents fighting and for emergency management. The functioning of these organisations critically depends upon efficient decision making and exchange of information. This project is aimed at securing and possibly improving the functionality and efficiency of the accident and emergency management by verifying, demonstrating, and validating the possible use of advanced information technology in the organisations mentioned above. With the nuclear industry in focus the project consists of five main activities: 1) The study and detailed analysis of accident and emergency scenarios based on records from incidents and rills in nuclear installations. 2) Development of a conceptual understanding of accident and emergency management with emphasis on distributed decision making, information flow, and control structure sthat are involved. 3) Development of a general experimental methodology for evaluating the effects of different kinds of decision aids and forms of organisation for emergency management systems with distributed decision making. 4) Development and test of a prototype system for a limited part of an accident and emergency organisation to demonstrate the potential use of computer and communication systems, data-base and knowledge base technology, and applications of expert systems and methods used in artificial intelligence. 5) Production of guidelines for the introduction of advanced information technology in the organisations based on evaluation and validation of the prototype system. (author)

  19. Accident management information needs

    International Nuclear Information System (INIS)

    Hanson, D.J.; Ward, L.W.; Nelson, W.R.; Meyer, O.R.

    1990-04-01

    In support of the US Nuclear Regulatory Commission (NRC) Accident Management Research Program, a methodology has been developed for identifying the plant information needs necessary for personnel involved in the management of an accident to diagnose that an accident is in progress, select and implement strategies to prevent or mitigate the accident, and monitor the effectiveness of these strategies. This report describes the methodology and presents an application of this methodology to a Pressurized Water Reactor (PWR) with a large dry containment. A risk-important severe accident sequence for a PWR is used to examine the capability of the existing measurements to supply the necessary information. The method includes an assessment of the effects of the sequence on the measurement availability including the effects of environmental conditions. The information needs and capabilities identified using this approach are also intended to form the basis for more comprehensive information needs assessment performed during the analyses and development of specific strategies for use in accident management prevention and mitigation. 3 refs., 16 figs., 7 tabs

  20. Accident management information needs

    Energy Technology Data Exchange (ETDEWEB)

    Hanson, D.J.; Ward, L.W.; Nelson, W.R.; Meyer, O.R. (EG and G Idaho, Inc., Idaho Falls, ID (USA))

    1990-04-01

    In support of the US Nuclear Regulatory Commission (NRC) Accident Management Research Program, a methodology has been developed for identifying the plant information needs necessary for personnel involved in the management of an accident to diagnose that an accident is in progress, select and implement strategies to prevent or mitigate the accident, and monitor the effectiveness of these strategies. This report describes the methodology and presents an application of this methodology to a Pressurized Water Reactor (PWR) with a large dry containment. A risk-important severe accident sequence for a PWR is used to examine the capability of the existing measurements to supply the necessary information. The method includes an assessment of the effects of the sequence on the measurement availability including the effects of environmental conditions. The information needs and capabilities identified using this approach are also intended to form the basis for more comprehensive information needs assessment performed during the analyses and development of specific strategies for use in accident management prevention and mitigation. 3 refs., 16 figs., 7 tabs.

  1. Database on aircraft accidents

    International Nuclear Information System (INIS)

    Nishio, Masahide; Koriyama, Tamio

    2013-11-01

    The Reactor Safety Subcommittee in the Nuclear Safety and Preservation Committee published 'The criteria on assessment of probability of aircraft crash into light water reactor facilities' as the standard method for evaluating probability of aircraft crash into nuclear reactor facilities in July 2002. In response to this issue, Japan Nuclear Energy Safety Organization has been collecting open information on aircraft accidents of commercial airplanes, self-defense force (SDF) airplanes and US force airplanes every year since 2003, sorting out them and developing the database of aircraft accidents for the latest 20 years to evaluate probability of aircraft crash into nuclear reactor facilities. In this report the database was revised by adding aircraft accidents in 2011 to the existing database and deleting aircraft accidents in 1991 from it, resulting in development of the revised 2012 database for the latest 20 years from 1992 to 2011. Furthermore, the flight information on commercial aircrafts was also collected to develop the flight database for the latest 20 years from 1992 to 2011 to evaluate probability of aircraft crash into reactor facilities. The method for developing the database of aircraft accidents to evaluate probability of aircraft crash into reactor facilities is based on the report 'The criteria on assessment of probability of aircraft crash into light water reactor facilities' described above. The 2012 revised database for the latest 20 years from 1992 to 2011 shows the followings. The trend of the 2012 database changes little as compared to the last year's report. (1) The data of commercial aircraft accidents is based on 'Aircraft accident investigation reports of Japan transport safety board' of Ministry of Land, Infrastructure, Transport and Tourism. The number of commercial aircraft accidents is 4 for large fixed-wing aircraft, 58 for small fixed-wing aircraft, 5 for large bladed aircraft and 99 for small bladed aircraft. The relevant accidents

  2. A Method for Thermal Dimensioning and for Energy Behavior Evaluation of a Building Envelope PCM Layer by Using the Characteristic Days

    Directory of Open Access Journals (Sweden)

    Domenico Mazzeo

    2017-05-01

    Full Text Available Net zero energy buildings (nZEB require the development of innovative technologies such as the use of phase change materials (PCMs in walls for the energy requalification of low inertia buildings. The presence of a PCM layer in the external building wall, due to the effect of storage and release of latent energy phenomena, modifies the energy behavior, both during the summer and winter periods. This paper addresses the problem of the definition of the energetic behavior of a layer subject to phase change with periodic non-sinusoidal boundary conditions, characterizing the external walls of air-conditioned buildings. In such conditions, the layer is the site of the formation of one or more bi-phase interfaces, which originate on the boundary surfaces, or are always present and fluctuate within the layer. It is also possible that the layer does not undergo any phase change. The study has been developed by a finite difference numeric calculation model which explicitly determines the number and the position of the bi-phase interfaces that originate in the layer and the temperature and the heat flux fields. The surface heat fluxes are used to evaluate the PCM layer energetic behavior in terms of energy transferred through the boundary surfaces and of stored energy in sensible and latent form. The proposed method employs the characteristic day that it is periodically repeated for all the days of the considered month. The use of the characteristic days drastically reduces the computational burden of the numerical calculation and it allows to obtain guidance on the behaviour of the PCM throughout the year, in accordance with the variability of external climatic conditions, in order to select the PCM with the most suitable thermophysical properties. The methodology developed is applied to PCM layers with different melting temperatures and subject to climatic conditions of two locations, one with a continental climate and the second one with a

  3. Historical aspects of radiation accidents

    International Nuclear Information System (INIS)

    Mettler, F.A. Jr.; Ricks, R.C.

    1990-01-01

    Radiation accidents are extremely rare events; however, the last two years have witnessed the largest radiation accidents in both the eastern and western hemispheres. It is the purpose of this chapter to review how radiation accidents are categorized, examine the temporal changes in frequency and severity, give illustrative examples of several types of radiation accidents, and finally, to describe the various registries for radiation accidents

  4. Phase change and heat transfer characteristics of a eutectic mixture of palmitic and stearic acids as PCM in a latent heat storage system

    International Nuclear Information System (INIS)

    Baran, Guelseren; Sari, Ahmet

    2003-01-01

    The phase change and heat transfer characteristics of a eutectic mixture of palmitic and stearic acids as phase change material (PCM) during the melting and solidification processes were determined experimentally in a vertical two concentric pipes energy storage system. This study deals with three important subjects. First is determination of the eutectic composition ratio of the palmitic acid (PA) and stearic acid (SA) binary system and measurement of its thermophysical properties by differential scanning calorimetry (DSC). Second is establishment of the phase transition characteristics of the mixture, such as the total melting and solidification temperatures and times, the heat transfer modes in the melted and solidified PCM and the effect of Reynolds and Stefan numbers as initial heat transfer fluid (HTF) conditions on the phase transition behaviors. Third is calculation of the heat transfer coefficients between the outside wall of the HTF pipe and the PCM, the heat recovery rates and heat fractions during the phase change processes of the mixture and also discussion of the effect of the inlet HTF parameters on these characteristics. The DSC results showed that the PA-SA binary system in the mixture ratio of 64.2:35.8 wt% forms a eutectic, which melts at 52.3 deg. C and has a latent heat of 181.7 J g -1 , and thus, these properties make it a suitable PCM for passive solar space heating and domestic water heating applications with respect to climate conditions. The experimental results also indicated that the eutectic mixture of PA-SA encapsulated in the annulus of concentric double pipes has good phase change and heat transfer characteristics during the melting and solidification processes, and it is an attractive candidate as a potential PCM for heat storage in latent heat thermal energy storage systems

  5. Accidents in nuclear ships

    Energy Technology Data Exchange (ETDEWEB)

    Oelgaard, P L [Risoe National Lab., Roskilde (Denmark); [Technical Univ. of Denmark, Lyngby (Denmark)

    1996-12-01

    This report starts with a discussion of the types of nuclear vessels accidents, in particular accidents which involve the nuclear propulsion systems. Next available information on 61 reported nuclear ship events in considered. Of these 6 deals with U.S. ships, 54 with USSR ships and 1 with a French ship. The ships are in almost all cases nuclear submarines. Only events that involve the sinking of vessels, the nuclear propulsion plants, radiation exposures, fires/explosions, sea-water leaks into the submarines and sinking of vessels are considered. For each event a summary of available information is presented, and comments are added. In some cases the available information is not credible, and these events are neglected. This reduces the number of events to 5 U.S. events, 35 USSR/Russian events and 1 French event. A comparison is made between the reported Soviet accidents and information available on dumped and damaged Soviet naval reactors. It seems possible to obtain good correlation between the two types of events. An analysis is made of the accident and estimates are made of the accident probabilities which are found to be of the order of 10{sup -3} per ship reactor years. It if finally pointed out that the consequences of nuclear ship accidents are fairly local and does in no way not approach the magnitude of the Chernobyl accident. It is emphasized that some of the information on which this report is based, may not be correct. Consequently some of the results of the assessments made may not be correct. (au).

  6. Accidents in nuclear ships

    International Nuclear Information System (INIS)

    Oelgaard, P.L.

    1996-12-01

    This report starts with a discussion of the types of nuclear vessels accidents, in particular accidents which involve the nuclear propulsion systems. Next available information on 61 reported nuclear ship events in considered. Of these 6 deals with U.S. ships, 54 with USSR ships and 1 with a French ship. The ships are in almost all cases nuclear submarines. Only events that involve the sinking of vessels, the nuclear propulsion plants, radiation exposures, fires/explosions, sea-water leaks into the submarines and sinking of vessels are considered. For each event a summary of available information is presented, and comments are added. In some cases the available information is not credible, and these events are neglected. This reduces the number of events to 5 U.S. events, 35 USSR/Russian events and 1 French event. A comparison is made between the reported Soviet accidents and information available on dumped and damaged Soviet naval reactors. It seems possible to obtain good correlation between the two types of events. An analysis is made of the accident and estimates are made of the accident probabilities which are found to be of the order of 10 -3 per ship reactor years. It if finally pointed out that the consequences of nuclear ship accidents are fairly local and does in no way not approach the magnitude of the Chernobyl accident. It is emphasized that some of the information on which this report is based, may not be correct. Consequently some of the results of the assessments made may not be correct. (au)

  7. School accidents in Austria.

    Science.gov (United States)

    Schalamon, Johannes; Eberl, Robert; Ainoedhofer, Herwig; Singer, Georg; Spitzer, Peter; Mayr, Johannes; Schober, Peter H; Hoellwarth, Michael E

    2007-09-01

    The aim of this study was to obtain information about the mechanisms and types of injuries in school in Austria. Children between 0 and 18 years of age presenting with injuries at the trauma outpatient in the Department of Pediatric Surgery in Graz and six participating hospitals in Austria were evaluated over a 2-year prospective survey. A total of 28,983 pediatric trauma cases were registered. Personal data, site of the accident, circumstances and mechanisms of accident and the related diagnosis were evaluated. At the Department of Pediatric Surgery in Graz 21,582 questionnaires were completed, out of which 2,148 children had school accidents (10%). The remaining 7,401 questionnaires from peripheral hospitals included 890 school accidents (12%). The male/female ratio was 3:2. In general, sport injuries were a predominant cause of severe trauma (42% severe injuries), compared with other activities in and outside of the school building (26% severe injuries). Injuries during ball-sports contributed to 44% of severe injuries. The upper extremity was most frequently injured (34%), followed by lower extremity (32%), head and neck area (26%) and injuries to thorax and abdomen (8%). Half of all school related injuries occur in children between 10 and 13 years of age. There are typical gender related mechanisms of accident: Boys get frequently injured during soccer, violence, and collisions in and outside of the school building and during craft work. Girls have the highest risk of injuries at ball sports other than soccer.

  8. Radiation accidents and dosimetry

    International Nuclear Information System (INIS)

    Sagstuen, E.; Theisen, H.; Henriksten, T.

    1982-12-01

    On September 2nd 1982 one of the employees of the gamma-irradiation facility at Institute for Energy Technology, Kjeller, Norway entered the irradiation cell with a 65.7 kCi *sp60*Co- source in unshielded position. The victim received an unknown radiation dose and died after 13 days. Using electron spin resonance spectroscopy, the radiation dose in this accident was subsequently determined based on the production of longlived free radicals in nitroglycerol tablets borne by the operator during the accident. He used nitroglycerol for heart problems and free radical are easily formed and trapped in sugar which is the main component of the tablets. Calibration experiments were carried out and the dose given to the tablets during the accident was determined to 37.2 +- 0.5 Gy. The general use of free radicals for dose determinations is discussed. (Auth.)

  9. Big nuclear accidents

    International Nuclear Information System (INIS)

    Marshall, W.

    1983-01-01

    Much of the debate on the safety of nuclear power focuses on the large number of fatalities that could, in theory, be caused by extremely unlikely but imaginable reactor accidents. This, along with the nuclear industry's inappropriate use of vocabulary during public debate, has given the general public a distorted impression of the safety of nuclear power. The way in which the probability and consequences of big nuclear accidents have been presented in the past is reviewed and recommendations for the future are made including the presentation of the long-term consequences of such accidents in terms of 'reduction in life expectancy', 'increased chance of fatal cancer' and the equivalent pattern of compulsory cigarette smoking. (author)

  10. Care of radiation accidents

    International Nuclear Information System (INIS)

    Renz, K.

    1983-01-01

    The small probability of a serious radiation accident happening dispenses neither the plants where radiation exposure occurs nor the employers' liability insurance associations from their obligation to make provision for such cases. On the other hand, the efforts involved in such preventive measures must be kept within reasonable limits. As a result of these considerations a concept for taking care of radiation accidents was developed that is based on already existing institutions. The most attention was demanded by questions of organization, logistics, communication and information. The syndrome appearing after acute whole-body irradiation is known. This syndrome in its different stages and the relative therapeutic measures form the basis for the organization of the care of radiation accidents. (orig./MG) [de

  11. Review of nuclear reactor accidents

    International Nuclear Information System (INIS)

    Connelly, J.W.; Storr, G.J.

    1989-01-01

    Two types of severe reactor accidents - loss of coolant or coolant flow and transient overpower (TOP) accidents - are described and compared. Accidents in research reactors are discussed. The 1961 SL1 accident in the US is used as an illustration as it incorporates the three features usually combined in a severe accident - a design flaw or flaws in the system, a circumvention of safety circuits or procedures, and gross operator error. The SL1 reactor, the reactivity accident and the following fuel-coolant interaction and steam explosion are reviewed. 3 figs

  12. Criticality accident alarm system

    International Nuclear Information System (INIS)

    Malenfant, R.E.

    1991-01-01

    The American National Standard ANSI/ANS-8.3-1986, Criticality Accident Alarm System provides guidance for the establishment and maintenance of an alarm system to initiate personnel evacuation in the event of inadvertent criticality. In addition to identifying the physical features of the components of the system, the characteristics of accidents of concern are carefully delineated. Unfortunately, this ANSI Standard has led to considerable confusion in interpretation, and there is evidence that the ''minimum accident of concern'' may not be appropriate. Furthermore, although intended as a guide, the provisions of the standard are being rigorously applied, sometimes with interpretations that are not consistent. Although the standard is clear in the use of absorbed dose in free air of 20 rad, at least one installation has interpreted the requirement to apply to dose in soft tissue. The standard is also clear in specifying the response to both neutrons and gamma rays. An assembly of uranyl fluoride enriched to 5% 235 U was operated to simulate a potential accident. The dose, delivered in a free run excursion 2 m from the surface of the vessel, was greater than 500 rad, without ever exceeding a rate of 20 rad/min, which is the set point for activating an alarm that meets the standard. The presence of an alarm system would not have prevented any of the five major accidents in chemical operations nor is it absolutely certain that the alarms were solely responsible for reducing personnel exposures following the accident. Nevertheless, criticality alarm systems are now the subject of great effort and expense. 13 refs

  13. Accident at Harrisburg

    International Nuclear Information System (INIS)

    1979-05-01

    The course of events during the accident on 28 March 1979 at Three Mile Island-2 Reactor at Harrisburg, Pennsylvania, is described in detail. The effects (in the environment and within the safety containment) are described. The following points are then discussed: the possibility of a comparable accident occurring in the nuclear power stations in the German Federal Republic; the possibility of any point having been overlooked in the design of nuclear power stations in the Federal Republic; whether previous risk analyses are still valid; and how near the Three Mile Island reactor was to a core meltdown. Some conclusions are drawn. (U.K.)

  14. Mortal radiological accident

    International Nuclear Information System (INIS)

    Gimenez, J.C.

    1987-01-01

    After defining the concept of 'Radiological accident', statistical data from Radiation Emergency Assistance Center of ORNL (United States of America) are given about the deaths caused by acute irradiation between 1944 and April 24, 1986 -ie, the day before Chernobyl nuclear accident- as well as on the number of deaths caused by the latter. Next the different clinical stages of the Acute Irradiation Syndrome (AIS) as well as its possible treatment are described, and finally the different physical, clinical and biological characteristics linked to the AIS and to its diagnosis and prognosis are discussed. (M.E.L.) [es

  15. The TMI-2 accident

    International Nuclear Information System (INIS)

    Loureiro, L.A.

    1986-01-01

    A critical study about the technical and man-related facts in order to establish what is considered the worst commercial nuclear power accident until 1986. Radiological consequences and stress to the public are considered in contrast to antinuclear groups. This descriptive and technical study has the purpose to document written and oral opinions obtained abroad and then explain to the public in an easy language terminology. Preliminary study describing safety related systems fails and the accident itself with minute to minute description, conduct to the consequences and then, to learned lessons

  16. Domino effect in chemical accidents: main features and accident sequences.

    Science.gov (United States)

    Darbra, R M; Palacios, Adriana; Casal, Joaquim

    2010-11-15

    The main features of domino accidents in process/storage plants and in the transportation of hazardous materials were studied through an analysis of 225 accidents involving this effect. Data on these accidents, which occurred after 1961, were taken from several sources. Aspects analyzed included the accident scenario, the type of accident, the materials involved, the causes and consequences and the most common accident sequences. The analysis showed that the most frequent causes are external events (31%) and mechanical failure (29%). Storage areas (35%) and process plants (28%) are by far the most common settings for domino accidents. Eighty-nine per cent of the accidents involved flammable materials, the most frequent of which was LPG. The domino effect sequences were analyzed using relative probability event trees. The most frequent sequences were explosion→fire (27.6%), fire→explosion (27.5%) and fire→fire (17.8%). Copyright © 2010 Elsevier B.V. All rights reserved.

  17. [Drugs and occupational accident].

    Science.gov (United States)

    Bratzke, H; Albers, C

    1996-02-01

    In a case of a fatal occupational accident (construction worker, fall from roof, urine test positive for cocaine and THC, e.g. cannabis) the question arised to what extent those drug-related occupational accidents occur. In the literature only few cases, mainly dealing with cannabis influence, have been reported, however, a higher number is suspected. Cocaine and other stimulating drugs (amphetamine) are more often used to increase physical fitness. By direct or indirect interference with vigilance these compounds may provoke accidents. Due to the lack of a legal basis proving of the influence of drugs at the working place is still very limited, although highly sensitive chemical-toxicological assay procedures are available to detect even the chronic abuse (in hair). In the general conditions of accident insurances a compensation is excluded when alcohol is involved, but drugs are not mentioned. It is indeed difficult to establish a concentration limit for drugs like that existing for alcohol (1.1%). In each case the assay of the drug involved and exact knowledge of its specific effects is in an essential prerequisite to prove the causal relationship.

  18. Note nuclear accidents combat

    International Nuclear Information System (INIS)

    1989-01-01

    In this document the starting points are described which underlie the new framework for the nuclear-accident combat in the Netherlands. All the elaboration of this is indicated in main lines. The juridical consequences of the proposed structure are enlightened and the sequel activities are indicated. (H.W.). 6 figs.; 8 tabs

  19. Measures against nuclear accidents

    International Nuclear Information System (INIS)

    1992-01-01

    A select committee appointed by the Norwegian Ministry of Social Affairs put forward proposals concerning measures for the improvement of radiation protection preparedness in Norway. On the basis on an assessment of the potential radiation accident threat, the report examines the process of response, and identifies the organizational and management factors that influence that process

  20. The Chernobyl reactor accident

    International Nuclear Information System (INIS)

    1986-01-01

    The documentation abstracted contains a complete survey of the broadcasts transmitted by the Russian wire service of the Deutsche Welle radio station between April 28 and Mai 15, 1986 on the occasion of the Chernobyl reactor accident. Access is given to extracts of the remarkable eastern and western echoes on the broadcasts of the Deutsche Welle. (HP) [de

  1. Lessons learned from accidents investigations

    Energy Technology Data Exchange (ETDEWEB)

    Zuniga-Bello, P. [Consejo Nacional de Ciencia y Tecnologia (CONACYT), Mexico City (Mexico); Croft, J. [National Radiological Protection Board (United Kingdom); Glenn, J

    1997-12-31

    Accidents from three main practices: medical applications, industrial radiography and industrial irradiators are used to illustrate some common causes of accidents and the main lessons to be learned. A brief description of some of these accidents is given. Lessons learned from the described accidents are approached by subjects covering: safety culture, quality assurance, human factors, good engineering practice, defence in depth, security of sources, safety assessment and monitoring and verification compliance. (author)

  2. Overview of core disruptive accidents

    International Nuclear Information System (INIS)

    Marchaterre, J.F.

    1977-01-01

    An overview of the analysis of core-disruptive accidents is given. These analyses are for the purpose of understanding and predicting fast reactor behavior in severe low probability accident conditions, to establish the consequences of such conditions and to provide a basis for evaluating consequence limiting design features. The methods are used to analyze core-disruptive accidents from initiating event to complete core disruption, the effects of the accident on reactor structures and the resulting radiological consequences are described

  3. Lessons learned from accident investigations

    International Nuclear Information System (INIS)

    Zuniga-Bello, P.; Croft, J.R.; Glenn, J.

    1998-01-01

    Accidents in three main practices - medical applications, industrial radiography and industrial irradiators - are used to illustrate some common causes of accidents and the main lessons to be learned from them. A brief description of some of these accidents is given. Lessons learned from the accidents described are approached bearing in mind: safety culture, quality assurance, human factors, good engineering practice, defence in depth, security of sources, safety assessment and monitoring and verification compliance. (author)

  4. Comparison between Possibilistic c-Means (PCM and Artificial Neural Network (ANN Classification Algorithms in Land use/ Land cover Classification

    Directory of Open Access Journals (Sweden)

    Ganchimeg Ganbold

    2017-03-01

    Full Text Available There are several statistical classification algorithms available for landuse/land cover classification. However, each has a certain bias orcompromise. Some methods like the parallel piped approach in supervisedclassification, cannot classify continuous regions within a feature. Onthe other hand, while unsupervised classification method takes maximumadvantage of spectral variability in an image, the maximally separableclusters in spectral space may not do much for our perception of importantclasses in a given study area. In this research, the output of an ANNalgorithm was compared with the Possibilistic c-Means an improvementof the fuzzy c-Means on both moderate resolutions Landsat8 and a highresolution Formosat 2 images. The Formosat 2 image comes with an8m spectral resolution on the multispectral data. This multispectral imagedata was resampled to 10m in order to maintain a uniform ratio of1:3 against Landsat 8 image. Six classes were chosen for analysis including:Dense forest, eucalyptus, water, grassland, wheat and riverine sand. Using a standard false color composite (FCC, the six features reflecteddifferently in the infrared region with wheat producing the brightestpixel values. Signature collection per class was therefore easily obtainedfor all classifications. The output of both ANN and FCM, were analyzedseparately for accuracy and an error matrix generated to assess the qualityand accuracy of the classification algorithms. When you compare theresults of the two methods on a per-class-basis, ANN had a crisperoutput compared to PCM which yielded clusters with pixels especiallyon the moderate resolution Landsat 8 imagery.

  5. Finite element modeling for integrated solid-solid PCM-building material with varying phase change temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, D.; Fung, A.S.; Siddiqui, O. [Ryerson Polytechnic Univ., Toronto, ON (Canada). Dept. of Mechanical and Industrial Engineering

    2008-08-15

    Solid-solid phase change materials (SSPCMs) are used to enhance thermal storage performance and reduce indoor temperature fluctuations in buildings. In this study, a finite element model (FEM) was used to investigate the thermal properties of different types of SSPCMs. An effective heat capacity method was used to develop the model. An integrated PCM-building material was analyzed in relation to temperature and heat flux profiles. Governing equations for the heat transfer process were composed of Navier-Stokes momentum equations; a mass conservation equation; and an energy conservation equation. Effective heat capacity was described as a linear function of the latent heat of fusion on both the heating and cooling processes. Data from the simulation were then compared with an experiment suing drywall, concrete and gypcrete samples. Heat flux across the surfaces and temperatures on the surfaces of the materials were measured. Data were used to validate the finite element model (FEM). Results of the study suggested that heat flux profiles are an effective means of understanding phase change processes. It was concluded that PCMs with lower phase change temperatures lengthened energy releases and improved thermal comfort in the building. 12 refs., 2 tabs., 14 figs.

  6. Experimental study on thermophysical properties of nanofluids as phase-change material (PCM) in low temperature cool storage

    International Nuclear Information System (INIS)

    He Qinbo; Wang Shuangfeng; Tong, Mingwei; Liu Yudong

    2012-01-01

    Highlights: ► The nanoparticles can reduce the supercooling degree of TiO 2 –BaCl 2 –H 2 O nanofluid PCMs. ► The TiO 2 –BaCl 2 –H 2 O nanofluids PCMs can be applied to industries low temperature energy storage. ► TiO 2 –BaCl 2 –H 2 O can be a candidate for low temperature PCM. - Abstract: In this article, a new sort of nanofluid phase change materials (PCMs) is developed by suspending a small amount of TiO 2 nanoparticles in saturated BaCl 2 aqueous solution. Its thermal conductivities, supercooling degree, latent heat, specific heat, and rheological behaviors of the nanofluids PCMs were investigated. The experimental results show that with volume fraction is 1.130%, the thermal conductivities of nanofluids PCMs is enhanced by 12.76% at −5 °C, the supercooling degree is reduced by 84.92%. The latent heat and specific heat are slightly decreased with suspending nanoparticles. The viscosity increased with the increasing volume fraction, which will have no effect on the cool storage system. The higher thermal performances of nanofluids PCMs indicate that they are suitable for the industries low temperature energy storage.

  7. Free cooling potential of a PCM-based heat exchanger coupled with a novel HVAC system for simultaneous heating and cooling of buildings

    DEFF Research Database (Denmark)

    Maccarini, Alessandro; Hultmark, Göran; Bergsøe, Niels Christian

    2018-01-01

    . In particular, a model of a PCM-based heat exchanger was developed in this work by using the programming language Modelica. This device was designed to store cold energy during night-time and release it during daytime through the water circuit. Results for a typical office building model showed...... that the integration of free cooling devices can significantly reduce the primary energy use of the novel HVAC system. In particular, the thermal plant configuration including the PCM-based heat exchanger made it possible to almost completely avoid the use of mechanical cooling, leading to annual primary energy......This article presents a simulation-based study that estimates the primary energy use of a novel HVAC system for different configurations of a thermal plant. The main characteristic of the system is its ability to provide simultaneous heating and cooling to buildings by using a single hydronic...

  8. EPRI research on accident management

    International Nuclear Information System (INIS)

    Oehlberg, R.N.; Chao, J.

    1991-01-01

    The paper discusses Nuclear Regulatory Commission (NRC) efforts regarding severe reactor accident management and the Nuclear Management and Resources Council (NUMAEX), activities. (EPRI) Electric Power Research Institute accident management program consists of the two products just mentioned plus one related to severe accident plant status information and the MAAP 4.0 computer code. These are briefly discussed

  9. Accident management on french PWRS

    International Nuclear Information System (INIS)

    Queniart, D.

    1990-06-01

    After a brief recall of French safety rationale, the reactor operation and severe accident management is given. The research and development aimed at developing accident management procedures and emergency organization in France for the case of a NPP accident are also given

  10. Variation of thermophysical parameters of PCM CaCl2.6H2O with dopant from T-history data analysis

    Science.gov (United States)

    Sutjahja, I. M.; Silalahi, Alfriska O.; Sukmawati, Nissa; Kurnia, D.; Wonorahardjo, S.

    2018-03-01

    T-history is a powerful method for deriving the thermophysical parameters of a phase change material (PCM), which consists of solid and liquid specific heats as well as latent heat enthalpy. The performance of a PCM for thermal energy storage could be altered by chemical dopants added directly to the PCM in order to form a stable suspension. We described in this paper the role of chemical dopants in the variation of thermophysical parameters for CaCl2 · 6H2O inorganic PCM with 1 wt% and 2 wt% dopant concentration and BaSO4 (1 wt%) as a nucleator using the T-history method. The dopant consists graphite and CuO nanoparticles. The data analysis follows the original method proposed by (Zhang et al 1999 Meas. Sci. Technol. 10 201–205) and its modification by (Hong et al 2004 Int. J. Refrig. 27 360–366). In addition, the enthalpy-temperature curve is obtained by adopting a method proposed by (Marín et al 2003 Meas. Sci. Technol. 14 184–189). We found that the solid specific heat tends to increase non-linearly with increased dopant concentration for all dopants. The increased liquid specific heat, however, indicates the optimum value for 1 wt% graphite dopant. In contrast, the CuO dopant shows a smaller increase in dopant concentration. The specific heat data are analyzed based on the interacting mesolayer model for a nanofluid. The heat of fusion show strong variation with dopant type, in agreement with other experimental data for various PCMs and dopant particles.

  11. Thermophysical Characterization of MgCl2·6H2O, Xylitol and Erythritol as Phase Change Materials (PCM for Latent Heat Thermal Energy Storage (LHTES

    Directory of Open Access Journals (Sweden)

    Stephan Höhlein

    2017-04-01

    Full Text Available The application range of existing real scale mobile thermal storage units with phase change materials (PCM is restricted by the low phase change temperature of 58 ∘ C for sodium acetate trihydrate, which is a commonly used storage material. Therefore, only low temperature heat sinks like swimming pools or greenhouses can be supplied. With increasing phase change temperatures, more applications like domestic heating or industrial process heat could be operated. The aim of this study is to find alternative PCM with phase change temperatures between 90 and 150 ∘ C . Temperature dependent thermophysical properties like phase change temperatures and enthalpies, densities and thermal diffusivities are measured for the technical grade purity materials xylitol (C 5 H 12 O 5 , erythritol (C 4 H 10 O 4 and magnesiumchloride hexahydrate (MCHH, MgCl 2 · 6H 2 O. The sugar alcohols xylitol and erythritol indicate a large supercooling and different melting regimes. The salt hydrate MgCl 2 · 6H 2 O seems to be a suitable candidate for practical applications. It has a melting temperature of 115.1 ± 0.1 ∘ C and a phase change enthalpy of 166.9 ± 1.2 J / g with only 2.8 K supercooling at sample sizes of 100 g . The PCM is stable over 500 repeated melting and solidification cycles at differential scanning calorimeter (DSC scale with only small changes of the melting enthalpy and temperature.

  12. Thermophysical Characterization of MgCl₂·6H₂O, Xylitol and Erythritol as Phase Change Materials (PCM) for Latent Heat Thermal Energy Storage (LHTES).

    Science.gov (United States)

    Höhlein, Stephan; König-Haagen, Andreas; Brüggemann, Dieter

    2017-04-24

    The application range of existing real scale mobile thermal storage units with phase change materials (PCM) is restricted by the low phase change temperature of 58 ∘ C for sodium acetate trihydrate, which is a commonly used storage material. Therefore, only low temperature heat sinks like swimming pools or greenhouses can be supplied. With increasing phase change temperatures, more applications like domestic heating or industrial process heat could be operated. The aim of this study is to find alternative PCM with phase change temperatures between 90 and 150 ∘ C . Temperature dependent thermophysical properties like phase change temperatures and enthalpies, densities and thermal diffusivities are measured for the technical grade purity materials xylitol (C 5 H 12 O 5 ), erythritol (C 4 H 10 O 4 ) and magnesiumchloride hexahydrate (MCHH, MgCl 2 · 6H 2 O). The sugar alcohols xylitol and erythritol indicate a large supercooling and different melting regimes. The salt hydrate MgCl 2 · 6H 2 O seems to be a suitable candidate for practical applications. It has a melting temperature of 115.1 ± 0.1 ∘ C and a phase change enthalpy of 166.9 ± 1.2 J / g with only 2.8 K supercooling at sample sizes of 100 g . The PCM is stable over 500 repeated melting and solidification cycles at differential scanning calorimeter (DSC) scale with only small changes of the melting enthalpy and temperature.

  13. Thermophysical Characterization of MgCl2·6H2O, Xylitol and Erythritol as Phase Change Materials (PCM) for Latent Heat Thermal Energy Storage (LHTES)

    Science.gov (United States)

    Höhlein, Stephan; König-Haagen, Andreas; Brüggemann, Dieter

    2017-01-01

    The application range of existing real scale mobile thermal storage units with phase change materials (PCM) is restricted by the low phase change temperature of 58 ∘C for sodium acetate trihydrate, which is a commonly used storage material. Therefore, only low temperature heat sinks like swimming pools or greenhouses can be supplied. With increasing phase change temperatures, more applications like domestic heating or industrial process heat could be operated. The aim of this study is to find alternative PCM with phase change temperatures between 90 and 150 ∘C. Temperature dependent thermophysical properties like phase change temperatures and enthalpies, densities and thermal diffusivities are measured for the technical grade purity materials xylitol (C5H12O5), erythritol (C4H10O4) and magnesiumchloride hexahydrate (MCHH, MgCl2·6H2O). The sugar alcohols xylitol and erythritol indicate a large supercooling and different melting regimes. The salt hydrate MgCl2·6H2O seems to be a suitable candidate for practical applications. It has a melting temperature of 115.1 ± 0.1 ∘C and a phase change enthalpy of 166.9 ± 1.2 J/g with only 2.8 K supercooling at sample sizes of 100 g. The PCM is stable over 500 repeated melting and solidification cycles at differential scanning calorimeter (DSC) scale with only small changes of the melting enthalpy and temperature. PMID:28772806

  14. Testing of a reactimeter for a light water reactor in the range + 500 to - 5000 pcm; Essai d'un reactimetre pour reacteur a eau legere dans la gamme + 500, - 5000 pcm

    Energy Technology Data Exchange (ETDEWEB)

    Chauvet, G [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1964-07-01

    This apparatus is designed to measure instantaneously the positive or negative reactivity of a uranium reactor moderated by light water, on condition that the point of departure is the critical state of the reactor, or an already known sub-critical state. Slight modifications only are required to adapt it to another type of reactor. It is an analogue computer which simply inverses the transfer function of the reactor; it is not therefore a model reactor of which the output voltage is connected by a servo-mechanism to the power of the reactor to give the reactivity; the principle of the calculation of the reactivity does not depend on a servomechanism. One of its disadvantages is that it cannot operate outside a power variation range of 2.5 decades. However the measurement of a negative reactivity value between 0 and 3000 pcm is immediate. It measures the reactivity without deducting it from the period; it therefore gives the reactivity very precisely both for divergence and convergence even through in this latter case the period does not in fact exist. The equipment makes it possible to calibrate very rapidly the control rods of a reactor (the rod-drop method), to measure the reactivity of an experiment in the core, and to measure certain temperature effects. It is also possible by introducing a control into the core at a measured rate, to deduce directly its efficiency curve. (author) [French] Cet appareil est destine a mesurer instantanement la reactivite positive ou negative d'un reacteur a uranium modere a l'eau legere, a condition de partir de l'etat critique du reacteur, ou eventuellement d'un etat sous-critique deja connu. De legeres modifications permettent de l'adapter a un autre type de moderateur. C'est un calculateur analogique, qui inverse purement et simplement la fonction de transfert du reacteur; ce n'est donc pas un simulateur de pile dont la tension de sortie est asservie a la puissance du reacteur pour elaborer la reactivite; le principe du

  15. Casebook on electric safety accidents

    International Nuclear Information System (INIS)

    1987-09-01

    This book gives concentration on electric safety accidents in domestic and abroad, which introduces general electrical safety with property of electricity, safe equipment and maintenance and protection of electric shock. It lists the cases of accident caused of electricity in domestic like accident in power substation, utilization equipment, load system and another accident by electricity like death in electric shock another by electricity like death in electric shock in new building construction, the cases caused of electricity in abroad like damage in electric shock by high voltage electric transformer, electric shock in summer and earth fault accident by fault cooling tower.

  16. Radiological accidents balance in medicine

    International Nuclear Information System (INIS)

    Nenot, J.C.

    1995-01-01

    This work deals with the radiological accidents in medicine. In medicine, the radiation accidents on medical personnel and patients can be the result of over dosage and bad focusing of radiotherapy sealed sources. Sometimes, the accidents, if they are unknown during a time enough for the source to be spread and to expose a lot of persons (in the case of source dismantling for instance) can take considerable dimensions. Others accidents can come from bad handling of linear accelerators and from radionuclide kinetics in some therapies. Some examples of accidents are given. (O.L.). 11 refs

  17. Three Mile Island accident

    International Nuclear Information System (INIS)

    Barre, B.; Olivier, E.; Roux, J.P.; Pelle, P.

    2010-01-01

    Deluded by equivocal instrumentation signals, operators at TMI-2 (Three Mile Island - unit 2) misunderstood what was going on in the reactor and for 2 hours were taking inadequate decisions that turned a reactor incident into a major nuclear event that led to the melting of about one third of the core. The TMI accident had worldwide impacts in the domain of nuclear safety. The main consequences in France were: 1) the introduction of the major accident approach and the reinforcement of crisis management; 2) the improvement of the reactor design, particularly that of the pressurizer valves; 3) the implementation of safety probabilistic studies; 4) a better taking into account of the feedback experience in reactor operations; and 5) a better taking into account of the humane factor in reactor safety. (A.C.)

  18. The ultimate nuclear accident

    International Nuclear Information System (INIS)

    Abdus Salam, A.

    1988-01-01

    The estimated energy equivalent of Chernobyl explosion was the 1/150 th of the explosive energy equivalent of atomic bomb dropped on Hiroshima; while the devastation that could be caused by the world's stock pile of nuclear weapons, could be equivalent to 160 millions of Chernobyl-like incidents. As known, the number of nuclear weapons is over 50,000 and 2000 nuclear weapons are sufficient to destroy the world. The Three Mile Island and Chernobyl accidents have been blamed on human factors but also the human element, particularly in the form of psychological stresses on those operating the nuclear weapons, could accidentally bring the world to a nuclear catastrophe. This opinion is encouraged by the London's Sunday Times magazine which gave a graphic description of life inside a nuclear submarine. So, to speak of nuclear reactor accidents and not of nuclear weapons is false security. (author)

  19. Chernobyl reactor accident

    International Nuclear Information System (INIS)

    Malinauskas, A.P.; Buchanan, J.R.; Lorenz, R.A.; Yamashita, T.

    1986-01-01

    On April 26, 1986, an explosion occurred at the newest of four operating nuclear reactors at the Chernobyl site in the USSR. The accident initiated an international technical exchange of almost unprecedented magnitude; this exchange was climaxed with a meeting at the International Atomic Energy Agency in Vienna during the week of August 25, 1986. The meeting was attended by more than 540 official representatives from 51 countries and 20 international organizations. Information gleaned from that technical exchange is presented in this report. A description of the Chernobyl reactor, which differs significantly from commercial US reactors, is presented, the accident scenario advanced by the Russian delegation is discussed, and observations that have been made concerning fission product release are described

  20. Nuclear ship accidents

    International Nuclear Information System (INIS)

    Oelgaard, P.L.

    1993-05-01

    In this report available information on 28 nuclear ship accident and incidents is considered. Of these 5 deals with U.S. ships and 23 with USSR ships. The ships are in almost all cases nuclear submarines. Only events that involve the nuclear propulsion plants, radiation exposures, fires/explosions and sea water leaks into the submarines are considered. Comments are made on each of the events, and at the end of the report an attempt is made to point out the weaknesses of the submarine designs which have resulted in the accidents. It is emphasized that much of the available information is of a rather dubious nature. consequently some of the assessments made may not be correct. (au)

  1. The Fukushima accident

    International Nuclear Information System (INIS)

    Maqua, M.; Stueck, R.

    2012-01-01

    On 11 March 2011, the Tohoku earthquake and the subsequent tsunami hit the Japanese east coast, causing more than 15,000 fatalities. To this date, 3,000 people are still missing. The Fukushima Dai-ichi NPP was the nuclear installation that was most affected by the tsunami. The earthquake cut off the NPP from the national grid. About 45 minutes later, the tsunami flooded units 1-4 and led to core meltdown events with large releases for units 1, 2 and 3. Unit 4 had been in refuelling outage at that time and lost the cooling of the spent fuel pool for several days. Considerable hydrogen explosions occurred in units 1, 3 and 4. Shortly after the accident, TEPCO started to mitigate the consequences of the accident by providing external cooling to the reactors and by removing the radioactive debris from the site. Great emphasis was laid on effective radiation protection measures for the clean-up workers. Thus, up to now there has been no fatality due to the radiation caused by the Fukushima accident. The main steps of the accident sequences are described, taking into account the latest findings of investigations performed by TEPCO or on behalf of the regulatory body. The presentation focuses on the description of the status of the Fukushima Dai-ichi nuclear power plant and the future steps for cleaning-up the site. In the presentation, the major phases of the roadmap that TEPCO has developed for the clean-up are highlighted. The risks associated with the current plant status and the clean-up phases are described. Abstract the content of the manuscript in a few lines.

  2. Severe accident management guidelines

    International Nuclear Information System (INIS)

    Uhle, Jennifer

    2014-01-01

    The events at Fukushima Daiichi have highlighted the importance of Severe Accident Management Guidelines (SAMGs). As the world has learned from the catastrophe and countries are considering changes to their nuclear regulatory programs, the content of SAMGs and their regulatory control are being evaluated. This presentation highlights several factors that are being addressed in the United States as rulemaking is underway pertaining to SAMGs. The question of how to be prepared for the unexpected is discussed with specific insights gleaned from Fukushima. (author)

  3. The Chernobyl reactor accident

    International Nuclear Information System (INIS)

    Rassow, J.

    1986-01-01

    The documentation aims at giving a clearly arranged account of facts, interrelations and comparative evaluations of general interest. It deals with the course of events, atmospheric dispersion and fallout of the substances released and discusses the basic principles of the metering of radioactive radiation, the calculation of body doses and comparative evaluations with the radioactive exposure and risks involved by other sources. The author intends to contribute to an objective discussion about the Chernobyl reactor accident and nuclear energy as such. (DG) [de

  4. Radiation accident in Vietnam

    International Nuclear Information System (INIS)

    Wheatley, J.

    1994-01-01

    In November 1992 a Vietnamese research physicist was working with a microtron accelerator when he received a radiation overexposure that required the subsequent amputation of his right hand. A team from the International Atomic Energy Agency visited Hanoi in March 1993 to carry out an investigation. It was concluded that the accident occurred primarily because of a lack of safety systems, although the lack of both written procedures and training in basic radiation safety were also major contributors. (author)

  5. PREVENTION OF OCCUPATIONAL ACCIDENTS

    Directory of Open Access Journals (Sweden)

    Jovica Jovanovic

    2004-01-01

    Full Text Available Medical services, physicians and nurses play an essential role in the plant safety program through primary treatment of injured workers and by helping to identify workplace hazards. The physician and nurse should participate in the worksite investigations to identify specific hazard or stresses potentially causing the occupational accidents and injuries and in planning the subsequent hazard control program. Physicians and nurses must work closely and cooperatively with supervisors to ensure the prompt reporting and treatment of all work related health and safety problems. Occupational accidents, work related injuries and fatalities result from multiple causes, affect different segments of the working population, and occur in a myriad of occupations and industrial settings. Multiple factors and risks contribute to traumatic injuries, such as hazardous exposures, workplace and process design, work organization and environment, economics, and other social factors. With such a diversity of theories, it will not be difficult to understand that there does not exist one single theory that is considered right or correct and is universally accepted. These theories are nonetheless necessary, but not sufficient, for developing a frame of reference for understanding accident occurrences. Prevention strategies are also varied, and multiple strategies may be applicable to many settings, including engineering controls, protective equipment and technologies, management commitment to and investment in safety, regulatory controls, and education and training. Research needs are thus broad, and the development and application of interventions involve many disciplines and organizations.

  6. Radiological accident of Goiania

    International Nuclear Information System (INIS)

    Palacios, Elias; Gimenez, J.C.

    1988-01-01

    The accident of Goiania that took place in September, 1987, was the consequence of the dismantlement of the teletherapy equipment containing a Cs 137 source. The activity of the source was of about 5,2.10 13 Bq(1.400 Ci) and was made up by 1.10 -1 Kg of ClCs. This is one of the worst accidents, involving medical or industrial source, which happened up to the moment. The accident and the criteria adopted to face the emergency are described. The characteristics of the irradiation and superficial and internal contamination of the persons affected caused any dosimetric evaluation to be particularly difficult. The emergency control managed by capable persons was carried out with the expected difficulties in some areas within the Goiania city. About 90 % of the material could be recovered, in the removal works, in order to be treated as radioactive waste. Conclusions that should be taken into account in Argentina are reached. The authors of the article took part in the emergency by helping the brazilian Authorities within the Mutual Assistance Agreement between Argentina and Braxil. (M.E.L.) [es

  7. Thule accident 1968

    International Nuclear Information System (INIS)

    Melgaard, L.; Moeller Kristensen, H.

    1987-01-01

    On January 21, 1968 an American B-52 bomber crashed on the ice at Thule in Nothern Greenland. The bomber carried 4 nuclear weapons that were destroyed. The radioactive material of the bombs was spread over a large area of the ice. About 850 Danes stayed at the Thule base in 1968 for a shorter or longer period. Out of these 850 probably between 70 and 170 men took part in the clearing after the accident. Danish and American authorities establised that the radioactive contamination from the accident was too small to cause any health effects. For that reason the Danish authorities did not follow the Danish workers in order to show late effects, if any. In defiance of the authorities' very cocksure attitude towards possible late effets parts of the Danish press in the Summer 1986 started to be interested in the matter and to search for previous Thule-workers. Up till January 1987 aboput 600 workers have been contacted by the press, trade unions, and private persons. About 500 out of the 600 workers report on illness, cancers and deaths. This report tries to compile the accessible informations on the matter, to descibe the possible radioactive and chemical effects, to compare the Thule accident with a similar incident in Spain in 1966, and to propose a comprehensive health examination of all the workers. (LN)

  8. Accidents and human factors

    International Nuclear Information System (INIS)

    Nishiwaki, Y.; Kawai, H.; Morishima, H.; Terano, T.; Sugeno, M.

    1984-01-01

    When the TMI accident occurred it was 4 a.m., an hour when the error potential of the operators would have been very high. The frequency of car and train accidents in Japan is also highest between 4 a.m. and 6 a.m. The error potential may be classified into five phases corresponding to the electroencephalogramic pattern (EEG). At phase 0, when the delta wave appears, a person is unconscious and in deep sleep; at phase I, when the theta wave appears, he is very tired, sleepy and subnormal; at phase II, when the alpha wave appears, he is normal, relaxed and passive; at phase III, when the beta wave appears, he is normal, clear-minded and active; at phase IV, when the strong beta or epileptic wave appears, he is hypernormal, excited and incapable of normal judgement. Should an accident occur at phase II, the brain condition may jump to phase IV. At this phase the error or accident potential is maximum. The response of the human brain to different types of noises and signals may vary somewhat for different individuals and for different groups of people. Therefore, the possibility that such differences in brain functions may influence the mental structure would be worthy of consideration in human factors and in the design of man-machine systems. Human reliability and performance would be affected by many factors: medical, physiological and psychological, etc. The uncertainty involved in human factors may not necessarily be probabilistic, but fuzzy. Therefore, it would be important to develop a theory by which both non-probabilistic uncertainties, or fuzziness, of human factors and the probabilistic properties of machines can be treated consistently. From the mathematical point of view, probabilistic measure is considered a special case of fuzzy measure. Therefore, fuzzy set theory seems to be an effective tool for analysing man-machine systems. To minimize human error and the possibility of accidents, new safety systems should not only back up man and make up for his

  9. Radiation accident/disaster

    International Nuclear Information System (INIS)

    Kida, Yoshiko; Hirohashi, Nobuyuki; Tanigawa, Koichi

    2013-01-01

    Described are the course of medical measures following Fukushima Daiichi Nuclear Power Plant (FNPP) Accident after the quake and tsunami (Mar. 11, 2011) and the future task for radiation accident/disaster. By the first hydrogen explosion in FNPP (Mar. 12), evacuation of residents within 20 km zone was instructed, and the primary base for measures of nuclear disaster (Off-site Center) 5 km afar from FNPP had to work as a front base because of damage of communicating ways, of saving of injured persons and of elevation of dose. On Mar. 13, the medical arrangement council consisting from stuff of Fukushima Medical University (FMU), National Institute of Radiological Sciences, Nuclear Safety Research Association and Prefectural officers was setup in residents' hall of Fukushima City, and worked for correspondence to persons injured or exposed, where communication about radiation and between related organizations was still poor. The Off-site Center's head section moved to Prefectural Office on Mar. 15 as headquarters. Early in the period, all residents evacuated from the 20 km zone, and in-hospital patients and nursed elderly were transported with vehicles, >50 persons of whom reportedly died mainly by their base diseases. The nation system of medicare for emergent exposure had consisted from the network of the primary to third facilities; there were 5 facilities in the Prefecture, 3 of which were localized at 4-9 km distance from FNPP and closed early after the Accident; and the secondary facility of FMU became responsible to all exposed persons. There was no death of workers of FNPP. Medical stuff also measured the ambient dose at various places near FNPP, having had risk of exposure. At the Accident, the important system of command, control and communication was found fragile and measures hereafter should be planned on assumption of the worst scenario of complete damage of the infrastructure and communication. It is desirable for Disaster Medical Assistance Team which

  10. Severe accident analysis methodology in support of accident management

    International Nuclear Information System (INIS)

    Boesmans, B.; Auglaire, M.; Snoeck, J.

    1997-01-01

    The author addresses the implementation at BELGATOM of a generic severe accident analysis methodology, which is intended to support strategic decisions and to provide quantitative information in support of severe accident management. The analysis methodology is based on a combination of severe accident code calculations, generic phenomenological information (experimental evidence from various test facilities regarding issues beyond present code capabilities) and detailed plant-specific technical information

  11. Stress in accident and post-accident management at Chernobyl

    International Nuclear Information System (INIS)

    Girard, P.; Dubreuil, G.H.

    1996-01-01

    The effects of the Chernobyl nuclear accident on the psychology of the affected population have been much discussed. The psychological dimension has been advanced as a factor explaining the emergence, from 1990 onwards, of a post-accident crisis in the main CIS countries affected. This article presents the conclusions of a series of European studies, which focused on the consequences of the Chernobyl accident. These studies show that the psychological and social effects associated with the post-accident situation arise from the interdependency of a number of complex factors exerting a deleterious effect on the population. We shall first attempt to characterise the stress phenomena observed among the population affected by the accident. Secondly, we will be presenting an anlysis of the various factors that have contributed to the emerging psychological and social features of population reaction to the accident and in post-accident phases, while not neglecting the effects of the pre-accident situation on the target population. Thirdly, we shall devote some initial consideration to the conditions that might be conducive to better management of post-accident stress. In conclusion, we shall emphasise the need to restore confidence among the population generally. (Author)

  12. Cernavoda CANDU severe accident evaluation

    International Nuclear Information System (INIS)

    Negut, G.; Marin, A.

    1997-01-01

    The papers present the activities dedicated to Romania Cernavoda Nuclear Power Plant first CANDU Unit severe accident evaluation. This activity is part of more general PSA assessment activities. CANDU specific safety features are calandria moderator and calandria vault water capabilities to remove the residual heat in the case of severe accidents, when the conventional heat sinks are no more available. Severe accidents evaluation, that is a deterministic thermal hydraulic analysis, assesses the accidents progression and gives the milestones when important events take place. This kind of assessment is important to evaluate to recovery time for the reactor operators that can lead to the accident mitigation. The Cernavoda CANDU unit is modeled for the of all heat sinks accident and results compared with the AECL CANDU 600 assessment. (orig.)

  13. Occupational accidents aboard merchant ships

    DEFF Research Database (Denmark)

    Hansen, H.L.; Nielsen, D.; Frydenberg, Morten

    2002-01-01

    Objectives: To investigate the frequency, circumstances, and causes of occupational accidents aboard merchant ships in international trade, and to identify risk factors for the occurrence of occupational accidents as well as dangerous working situations where possible preventive measures may...... be initiated. Methods: The study is a historical follow up on occupational accidents among crew aboard Danish merchant ships in the period 1993–7. Data were extracted from the Danish Maritime Authority and insurance data. Exact data on time at risk were available. Results: A total of 1993 accidents were...... aboard. Relative risks for notified accidents and accidents causing permanent disability of 5% or more were calculated in a multivariate analysis including ship type, occupation, age, time on board, change of ship since last employment period, and nationality. Foreigners had a considerably lower recorded...

  14. Accident management insights after the Fukushima Daiichi NPP accident

    International Nuclear Information System (INIS)

    Degueldre, Didier; Viktorov, Alexandre; Tuomainen, Minna; Ducamp, Francois; Chevalier, Sophie; Guigueno, Yves; Tasset, Daniel; Heinrich, Marcus; Schneider, Matthias; Funahashi, Toshihiro; Hotta, Akitoshi; Kajimoto, Mitsuhiro; Chung, Dae-Wook; Kuriene, Laima; Kozlova, Nadezhda; Zivko, Tomi; Aleza, Santiago; Jones, John; McHale, Jack; Nieh, Ho; Pascal, Ghislain; ); Nakoski, John; Neretin, Victor; Nezuka, Takayoshi; )

    2014-01-01

    The Fukushima Daiichi nuclear power plant (NPP) accident, that took place on 11 March 2011, initiated a significant number of activities at the national and international levels to reassess the safety of existing NPPs, evaluate the sufficiency of technical means and administrative measures available for emergency response, and develop recommendations for increasing the robustness of NPPs to withstand extreme external events and beyond design basis accidents. The OECD Nuclear Energy Agency (NEA) is working closely with its member and partner countries to examine the causes of the accident and to identify lessons learnt with a view to the appropriate follow-up actions to be taken by the nuclear safety community. Accident management is a priority area of work for the NEA to address lessons being learnt from the accident at the Fukushima Daiichi NPP following the recommendations of Committee on Nuclear Regulatory Activities (CNRA), Committee on the Safety of Nuclear Installations (CSNI), and Committee on Radiation Protection and Public Health (CRPPH). Considering the importance of these issues, the CNRA authorised the formation of a task group on accident management (TGAM) in June 2012 to review the regulatory framework for accident management following the Fukushima Daiichi NPP accident. The task group was requested to assess the NEA member countries needs and challenges in light of the accident from a regulatory point of view. The general objectives of the TGAM review were to consider: - enhancements of on-site accident management procedures and guidelines based on lessons learnt from the Fukushima Daiichi NPP accident; - decision-making and guiding principles in emergency situations; - guidance for instrumentation, equipment and supplies for addressing long-term aspects of accident management; - guidance and implementation when taking extreme measures for accident management. The report is built on the existing bases for capabilities to respond to design basis

  15. CANDU severe accident analysis

    International Nuclear Information System (INIS)

    Negut, Gheorghe; Catana, Alexandru; Prisecaru, Ilie; Dupleac, Daniel

    2007-01-01

    Romania is a EU member since January first 2007. This country faces now new challenges which imply also the nuclear power reactors now in operation. Romania operates since 1996 a CANDU nuclear power reactor and soon will start up a second unit. In EU PWR reactors are mostly operated, so that the Romania's reactors have to meet EU standards. Safety analysis guidelines require to model severe accidents for reactors of this type. Starting from previous studies a thermal-hydraulic model for a degraded CANDU core was developed. The initiating event is assumed to be a LOCA with simultaneous loss of moderator and coolant and the failure of emergency core cooling system (ECCS). This type of accident is likely to modify the reactor geometry and will lead to a severe accident development. When the coolant temperatures inside a pressure tube reaches 1000 deg. C, a contact between pressure tube and calandria tube occurs and the decay heat is transferred to the moderator. Due to the lack of cooling, the moderator eventually begins to boil and is expelled, through the calandria vessel relief ducts, into the containment. Therefore the calandria tubes (fuel channels) uncover, then disintegrate and fall down to the calandria vessel bottom. All the quantity of calandria moderator is vaporized and expelled, the debris will heat up and eventually boil. The heat accumulated in the molten debris will be transferred through the calandria vessel wall to the shield water tank surrounding the calandria vessel. The thermal hydraulics phenomena described above are modeled, analyzed and compared with the existing data. (authors)

  16. Chernobyl reactor accident

    International Nuclear Information System (INIS)

    1986-05-01

    Following the accident at Chernobyl nuclear reactor, WHO organized on 6 May 1986 in Copenhagen a one day consultation of experts with knowledge in the fields of meteorology, radiation protection, biological effects, reactor technology, emergency procedures, public health and psychology in order to analyse the development of events and their consequences and to provide guidance as to the needs for immediate public health action. The present report provides detailed information on the transportation and dispersion of the radioactive material in the atmosphere, especially volatile elements, during the release period 26 April - 5 May. Presented are the calculated directions and locations of the radioactive plume over Europe in the first 5 days after the accident, submitted by the Swedish Meteorological and Hydrological Institute. The calculations have been made for two heights, 1500m and 750m and the plume directions are grouped into five periods, covering five European areas. The consequences of the accident inside the USSR and the radiological consequences outside the USSR are presented including the exposure routes and the biological effects, paying particular attention to iodine-131 effects. Summarized are the first reported measured exposure rates above background, iodine-131 deposition and concentrations in milk and the remedial actions taken in various European countries. Concerning the cesium-137 problem, based on the UNSCEAR assessment of the consequences of the nuclear fallout, one concludes that the cesium contamination outside the USSR is not likely to cause any serious problems. Finally, the conclusions and the recommendations of the meeting, taking into account both the short-term and longer term considerations are presented

  17. Traffic accidents: an econometric investigation

    OpenAIRE

    Tito Moreira; Adolfo Sachsida; Loureiro Paulo

    2004-01-01

    Based on a sample of drivers in Brasilia's streets, this article investigates whether distraction explains traffic accidents. A probit model is estimated to determine the predictive power of several variables on traffic accidents. The main conclusion drawn from this study is that the proxies used to measure distraction, such as the use of cell phones and cigarette smoking in a moving vehicle, are significant factors in determining traffic accidents.

  18. Medical aspects of radiation accidents

    International Nuclear Information System (INIS)

    Messerschmidt, O.

    1990-01-01

    Reactor accidents and nuclear bomb explosions are compared including the release of radioactivity in an accident, results of risk studies, emergency measures of nuclear power plants, and evacuation of the population. The medical aspects refer to the prophylaxies of the thyroid gland, contamination and decontamination of body surfaces, recommendations of the ICRP, radiation injury after total body exposure and medical problems after a reactor accident. (DG)

  19. Accident management approach in Armenia

    International Nuclear Information System (INIS)

    Ghazaryan, K.

    1999-01-01

    In this lecture the accident management approach in Armenian NPP (ANPP) Unit 2 is described. List of BDBAs had been developed by OKB Gydropress in 1994. 13 accident sequences were included in this list. The relevant analyses had been performed in VNIIAES and the 'Guidelines on operator actions for beyond design basis accident (BDBA) management at ANPP Unit 2' had been prepared. These instructions are discussed

  20. Nuclear accidents and protection

    International Nuclear Information System (INIS)

    Biocanin, R.; Amidzic, B.

    2005-01-01

    The numerous threats are our cruel reality. There is a great arsenal of nuclear weapons. Nuclear terrorism and nuclear accidents are always possible, especially during the transport and handling different nuclear material. Terrorist organisation also goes for coming into the possession of the nuclear means. Specific and important problem is human radioactive contamination in using nuclear energy for peaceful and military purpose. So, realisation of the universal and united system of NBCD gives us a possibility by using the modern communication equipment and very effective mobile units to react in a real time and successfully perform monitoring, alarming, protection and decontamination. (author) [sr

  1. The accident of Chernobyl

    International Nuclear Information System (INIS)

    1986-10-01

    RBMK reactors (reactor control, protection systems, containment) and the nuclear power plant of Chernobyl are first presented. The scenario of the accident is given with a detailed chronology. The actions and consequences on the site are reviewed. This report then give the results of the source term estimation (fision product release, core inventory, trajectories, meteorological data...), the radioactivity measurements obtained in France. Health consequences for the French population are evoked. The medical consequences for the population who have received a high level of doses are reviewed [fr

  2. Psychological response of accident

    International Nuclear Information System (INIS)

    Novikov, V.S.; Nikiforov, A.M.; Cheprasov, V.Yu.

    1996-01-01

    The psychological status of rescuers of consequences of Chernobyl[s accidents, having planned stationary examination and treatment of common somatic diseases, has been examined. THe age of men represented the study group was 35-54 years old. The results of medical-psychological examination showed the development in rescuers of common dysadaptation and stress state, characterized by depressive-hypochondriac state with high anxiety. The course of psychotherapeutic activities made possible to improve essentionally the psychological status of the patients. 12 refs., 3 figs., 1 tab

  3. Reactor accident in Chernobyl

    International Nuclear Information System (INIS)

    Sokalski, A.; Kowalski, A.

    1990-11-01

    The bibliography contains 1568 descriptions of papers devoted to Chernobylsk accident and recorded in ''INIS Atomindex'' to 30 June 1990. The descriptions were taken from ''INIS Atomindex'' and are presented in accordance with volumes of this journal (chronology of recording). Therefore all descriptions have numbers showing first the number of volume and then the number of record. The bibliography has at the end the detailed subject index consisting of 465 main headings and a lot of qualifiers. Some of them are descriptors taken from ''INIS Atomindex'' and some are key words taken from natural language. The index is in English as descriptions in the bibliography. (author)

  4. Accident prevention programme

    International Nuclear Information System (INIS)

    1978-01-01

    This study by the Steel Industry Safety and Health Commission was made within the context of the application by undertakings of the principles of accident and disease prevention previously adopted by the said Commission. It puts forward recommendations for the effective and gradual implementation of a programme of action on occupational health and safety in the various departments of an undertaking and in the undertaking as a whole. The methods proposed in this study are likely to be of interest to all undertakings in the metallurgical industry and other industrial sectors

  5. Serious accident in Peru

    International Nuclear Information System (INIS)

    Anon.

    1999-01-01

    A peruvian man, victim of an important accidental irradiation arrived on the Saturday twenty ninth of may 1999 to the centre of treatment of serious burns at the Percy military hospital (Clamart -France). The accident spent on the twentieth of February 1999, on the site of a hydroelectric power plant, in construction at 300 km at the East of Lima. The victim has picked up an industrial source of iridium devoted to gamma-graphy operations and put it in his back pocket; of trousers. The workman has serious radiation burns. (N.C.)

  6. Form-stable LiNO_3–NaNO_3–KNO_3–Ca(NO_3)_2/calcium silicate composite phase change material (PCM) for mid-low temperature thermal energy storage

    International Nuclear Information System (INIS)

    Jiang, Zhu; Leng, Guanghui; Ye, Feng; Ge, Zhiwei; Liu, Chuanping; Wang, Li; Huang, Yun; Ding, Yulong

    2015-01-01

    Graphical abstract: The figure (a) displays the microstructure of calcium silicate and the inset figure is the LiNO_3–NaNO_3–KNO_3–Ca(NO_3)_2/calcium silicate composite PCM. Calcium silicate is used as a porous skeleton material which could absorb large amounts of the nitrate PCM in voids and prevent the PCM from leakage during phase change process. Figure (b) shows the heat capacity of the composite PCM and the inset figure is the DSC curve of the composite. It indicates that this composite has a low melting point (103.5 °C) and good energy storage property. Based on the novel LiNO_3–NaNO_3–KNO_3–Ca(NO_3)_2/calcium silicate composite PCM, this work involves fabrication process, thermal and microstructural characterization, and chemical and physical stability measurements. - Highlights: • A novel LiNO_3–NaNO_3–KNO_3–Ca(NO_3)_2/calcium silicate composite PCM was prepared. • It has a low melting point (103.5 °C) and could remain stable until 585.5 °C. • It could keep form-stable without leakage during phase change process. • Thermal conductivity of the composite PCM reaches up to 1.177 W m"−"1 K"−"1. • It shows good thermal reliability after 1000 times heating and cooling cycling. - Abstract: In this paper, a novel form-stable LiNO_3–NaNO_3–KNO_3–Ca(NO_3)_2/calcium silicate composite PCM was developed by cold compression and sintering. The eutectic quaternary nitrate is used as PCM, while calcium silicate is used as structural supporting material. X-ray Diffraction (XRD) shows the PCM and the supporting material have good chemical compatibility. This composite PCM has a low melting point (103.5 °C) and remain stable without decomposition until 585.5 °C. Moreover, this composite shows excellent long term stability after 1000 melting and freezing cycles. Thermal conductivity of the composite was measured to be 1.177 W m"−"1 K"−"1, and that could be increased by adding thermal conductivity enhancers into the composite

  7. Credible investigation of air accidents

    International Nuclear Information System (INIS)

    Smart, K.

    2004-01-01

    Within the United Kingdom the Air Accidents Investigation Branch (AAIB) has been used as a model for the other transport modes accident investigation bodies. Government Ministers considered that the AAIB's approach had established the trust of the public and the aviation industry in its ability to conduct independent and objective investigations. The paper will examine the factors that are involved in establishing this trust. They include: the investigation framework; the actual and perceived independence of the accident investigating body; the aviation industry's safety culture; the qualities of the investigators and the quality of their liaison with bereaved families those directly affected by the accidents they investigate

  8. Guidance on accidents involving radioactivity

    International Nuclear Information System (INIS)

    1989-01-01

    This annex contains advice to Health Authorities on their response to accidents involving radioactivity. The guidance is in six parts:-(1) planning the response required to nuclear accidents overseas, (2) planning the response required to UK nuclear accidents a) emergency plans for nuclear installations b) nuclear powered satellites, (3) the handling of casualties contaminated with radioactive substances, (4) background information for dealing with queries from the public in the event of an accident, (5) the national arrangements for incident involving radioactivity (NAIR), (6) administrative arrangements. (author)

  9. 1976 Hanford americium accident

    International Nuclear Information System (INIS)

    Heid, K.R.; Breitenstein, B.D.; Palmer, H.E.; McMurray, B.J.; Wald, N.

    1979-01-01

    This report presents the 2.5-year medical course of a 64-year-old Hanford nuclear chemical operator who was involved in an accident in an americium recovery facility in August 1976. He was heavily externally contaminated with americium, sustained a substantial internal deposition of this isotope, and was burned with concentrated nitric acid and injured by flying debris about the face and neck. The medical care given the patient, including the decontamination efforts and clinical laboratory studies, are discussed. In-vivo measurements were used to estimate the dose rates and the accumulated doses to body organs. Urinary and fecal excreta were collected and analyzed for americium content. Interpretation of these data was complicated by the fact that the intake resulted both from inhalation and from solubilization of the americium embedded in facial tissues. A total of 1100 μCi was excreted in urine and feces during the first 2 years following the accident. The long-term use of diethylenetriaminepentate (DTPA), used principally as the zinc salt, is discussed including the method, route of administration, and effectiveness. To date, the patient has apparently experienced no complications attributable to this extensive course of therapy, even though he has been given approximately 560 grams of DTPA. 4 figures, 1 table

  10. Serious reactor accidents reconsidered

    International Nuclear Information System (INIS)

    1987-12-01

    The chance is determined for damage of the reactor core and that sequel events will cause excursion of radioactive materials into the environment. The gravity of such an accident is expressed by the source term. It appears that the chance for such an accident varies with the source term. In general it is valid that how larger the source term how smaller the chance is for it and vice versa. The chance for excursion is related to two complexes of events: serious damage (meltdown) of the reactor core, and the escape of the liberated radionuclides into the environment. The results are an order of magnitude consideration of the relation between the extent of the source term and the chance for it. From the spectrum of possible source terms three representative ones have been chosen: a large, a medium and a relative small source term. This choice is in accordance with international considerations. The hearth of this study is the estimation of the chance for occurrence of the three chosen source terms for new light-water reactors. refs.; figs.; tabs

  11. Assessment of accident energetics in LMFBR core-disruptive accidents

    International Nuclear Information System (INIS)

    Fauske, H.K.

    1977-01-01

    An assessment of accident energetics in LMFBR core-disruptive accidents is given with emphasis on the generic issues of energetic recriticality and energetic fuel-coolant interaction events. Application of a few general behavior principles to the oxide-fueled system suggests that such events are highly unlikely following a postulated core meltdown event

  12. Accident analysis. A review of the various accidents classifications

    International Nuclear Information System (INIS)

    Martin Martin, L.; Figueras, J.M.

    1982-01-01

    The objective of the accident analysis, in relation with the safety evaluation, environmental impact and emergency planning, should be to identify the total risk to the population and workers from potential accidents in the facility, analizing it over full spectrum of severity. (auth.)

  13. Diseño e implementación de un codec digital de audio con FPGA, en formato PCM, de 2 canales con interfaz para usuario

    Directory of Open Access Journals (Sweden)

    Edwar Jacinto G.

    2010-06-01

    Full Text Available This document describes the process to create a device of digital process with encoding process and decoding in PCM format, with the development of digital filters and the picoblaze microprocessor bymeans of the implementation in Spartan-3E Starter KitBoard from XILINX, also it describes the work out made about some modules that have this one in order to get the best quality in device, other phases with less value as the signal conditioning, amplification in phase input and output, as well as joining together toward the board.

  14. Containment severe accident thermohydraulic phenomena

    International Nuclear Information System (INIS)

    Frid, W.

    1991-08-01

    This report describes and discusses the containment accident progression and the important severe accident containment thermohydraulic phenomena. The overall objective of the report is to provide a rather detailed presentation of the present status of phenomenological knowledge, including an account of relevant experimental investigations and to discuss, to some extent, the modelling approach used in the MAAP 3.0 computer code. The MAAP code has been used in Sweden as the main tool in the analysis of severe accidents. The dependence of the containment accident progression and containment phenomena on the initial conditions, which in turn are heavily dependent on the in-vessel accident progression and phenomena as well as associated uncertainties, is emphasized. The report is in three parts dealing with: * Swedish reactor containments, the severe accident mitigation programme in Sweden and containment accident progression in Swedish PWRs and BWRs as predicted by the MAAP 3.0 code. * Key non-energetic ex-vessel phenomena (melt fragmentation in water, melt quenching and coolability, core-concrete interaction and high temperature in containment). * Early containment threats due to energetic events (hydrogen combustion, high pressure melt ejection and direct containment heating, and ex-vessel steam explosions). The report concludes that our understanding of the containment severe accident progression and phenomena has improved very significantly over the parts ten years and, thereby, our ability to assess containment threats, to quantify uncertainties, and to interpret the results of experiments and computer code calculations have also increased. (au)

  15. Expert software for accident identification

    International Nuclear Information System (INIS)

    Dobnikar, M.; Nemec, T.; Muehleisen, A.

    2003-01-01

    Each type of an accident in a Nuclear Power Plant (NPP) causes immediately after the start of the accident variations of physical parameters that are typical for that type of the accident thus enabling its identification. Examples of these parameter are: decrease of reactor coolant system pressure, increase of radiation level in the containment, increase of pressure in the containment. An expert software enabling a fast preliminary identification of the type of the accident in Krsko NPP has been developed. As input data selected typical parameters from Emergency Response Data System (ERDS) of the Krsko NPP are used. Based on these parameters the expert software identifies the type of the accident and also provides the user with appropriate references (past analyses and other documentation of such an accident). The expert software is to be used as a support tool by an expert team that forms in case of an emergency at Slovenian Nuclear Safety Administration (SNSA) with the task to determine the cause of the accident, its most probable scenario and the source term. The expert software should provide initial identification of the event, while the final one is still to be made after appropriate assessment of the event by the expert group considering possibility of non-typical events, multiple causes, initial conditions, influences of operators' actions etc. The expert software can be also used as an educational/training tool and even as a simple database of available accident analyses. (author)

  16. Fukushima accident - reasons and impacts

    International Nuclear Information System (INIS)

    Slugen, V.

    2011-01-01

    The Fukushima accident influenced dramatically the current view on safety of nuclear facilities. Consideration about possible impacts of natural catastrophe in design of nuclear facilities seems to be much more important than before. European commission is focused on the stress-tests at nuclear power plants. His paper will go more in details having in mind reasons and impacts of Fukushima accident (Author)

  17. First Responders and Criticality Accidents

    Energy Technology Data Exchange (ETDEWEB)

    Valerie L. Putman; Douglas M. Minnema

    2005-11-01

    Nuclear criticality accident descriptions typically include, but do not focus on, information useful to first responders. We studied these accidents, noting characteristics to help (1) first responders prepare for such an event and (2) emergency drill planners develop appropriate simulations for training. We also provide recommendations to help people prepare for such events in the future.

  18. Occupational accidents among mototaxi drivers.

    Science.gov (United States)

    Amorim, Camila Rego; de Araújo, Edna Maria; de Araújo, Tânia Maria; de Oliveira, Nelson Fernandes

    2012-03-01

    The use of motorcycles as a means of work has contributed to the increase in traffic accidents, in particular, mototaxi accidents. The aim of this study was to estimate and characterize the incidence of occupational accidents among the mototaxis registered in Feira de Santana, BA. This is a cross-sectional study with descriptive and census data. Of the 300 professionals registered at the Municipal Transportation Service, 267 professionals were interviewed through a structured questionnaire. Then, a descriptive analysis was conducted and the incidence of accidents was estimated based on the variables studied. Relative risks were calculated and statistical significance was determined using the chi-square test and Fisher's exact test, considering p accidents were observed in 10.5% of mototaxis. There were mainly minor injuries (48.7%), 27% of them requiring leaves of absence from work. There was an association between the days of work per week, fatigue in lower limbs and musculoskeletal complaints, and accidents. Knowledge of the working conditions and accidents involved in this activity can be of great importance for the adoption of traffic education policies, and to help prevent accidents by improving the working conditions and lives of these professionals.

  19. Barriers to learning from incidents and accidents

    NARCIS (Netherlands)

    Dechy, N.; Dien, Y.; Drupsteen, L.; Felicio, A.; Cunha, C.; Roed-Larsen, S.; Marsden, E.; Tulonen, T.; Stoop, J.; Strucic, M.; Vetere Arellano, A.L.; Vorm, J.K.J. van der; Benner, L.

    2015-01-01

    This document provides an overview of knowledge concerning barriers to learning from incidents and accidents. It focuses on learning from accident investigations, public inquiries and operational experience feedback, in industrial sectors that are exposed to major accident hazards. The document

  20. Probability of spent fuel transportation accidents

    International Nuclear Information System (INIS)

    McClure, J.D.

    1981-07-01

    The transported volume of spent fuel, incident/accident experience and accident environment probabilities were reviewed in order to provide an estimate of spent fuel accident probabilities. In particular, the accident review assessed the accident experience for large casks of the type that could transport spent (irradiated) nuclear fuel. This review determined that since 1971, the beginning of official US Department of Transportation record keeping for accidents/incidents, there has been one spent fuel transportation accident. This information, coupled with estimated annual shipping volumes for spent fuel, indicated an estimated annual probability of a spent fuel transport accident of 5 x 10 -7 spent fuel accidents per mile. This is consistent with ordinary truck accident rates. A comparison of accident environments and regulatory test environments suggests that the probability of truck accidents exceeding regulatory test for impact is approximately 10 -9 /mile

  1. 29 CFR 1960.29 - Accident investigation.

    Science.gov (United States)

    2010-07-01

    ... reflective of the seriousness of the accident. (b) In any case, each accident which results in a fatality or... evidence uncovered during accident investigations which would be of benefit in developing a new OSHA...

  2. Traffic Accidents on Slippery Roads

    DEFF Research Database (Denmark)

    Fonnesbech, J. K.; Bolet, Lars

    2014-01-01

    Police registrations from 65 accidents on slippery roads in normally Danish winters have been studied. The study showed: • 1 accident per 100 km when using brine spread with nozzles • 2 accidents per 100 km when using pre wetted salt • 3 accidents per 100 km when using kombi spreaders The results...... of accidents in normally Danish winter seasons are remarkable alike the amount of salt used in praxis in the winter 2011/2012. • 2.7 ton NaCl/km when using brine spread with nozzles • 5 ton NaCl/km when using pre wetted salt. • 5.7 ton NaCl/km when using kombi spreaders The explanation is that spreading...

  3. Accident sequence quantification with KIRAP

    International Nuclear Information System (INIS)

    Kim, Tae Un; Han, Sang Hoon; Kim, Kil You; Yang, Jun Eon; Jeong, Won Dae; Chang, Seung Cheol; Sung, Tae Yong; Kang, Dae Il; Park, Jin Hee; Lee, Yoon Hwan; Hwang, Mi Jeong.

    1997-01-01

    The tasks of probabilistic safety assessment(PSA) consists of the identification of initiating events, the construction of event tree for each initiating event, construction of fault trees for event tree logics, the analysis of reliability data and finally the accident sequence quantification. In the PSA, the accident sequence quantification is to calculate the core damage frequency, importance analysis and uncertainty analysis. Accident sequence quantification requires to understand the whole model of the PSA because it has to combine all event tree and fault tree models, and requires the excellent computer code because it takes long computation time. Advanced Research Group of Korea Atomic Energy Research Institute(KAERI) has developed PSA workstation KIRAP(Korea Integrated Reliability Analysis Code Package) for the PSA work. This report describes the procedures to perform accident sequence quantification, the method to use KIRAP's cut set generator, and method to perform the accident sequence quantification with KIRAP. (author). 6 refs

  4. Accident sequence quantification with KIRAP

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Tae Un; Han, Sang Hoon; Kim, Kil You; Yang, Jun Eon; Jeong, Won Dae; Chang, Seung Cheol; Sung, Tae Yong; Kang, Dae Il; Park, Jin Hee; Lee, Yoon Hwan; Hwang, Mi Jeong

    1997-01-01

    The tasks of probabilistic safety assessment(PSA) consists of the identification of initiating events, the construction of event tree for each initiating event, construction of fault trees for event tree logics, the analysis of reliability data and finally the accident sequence quantification. In the PSA, the accident sequence quantification is to calculate the core damage frequency, importance analysis and uncertainty analysis. Accident sequence quantification requires to understand the whole model of the PSA because it has to combine all event tree and fault tree models, and requires the excellent computer code because it takes long computation time. Advanced Research Group of Korea Atomic Energy Research Institute(KAERI) has developed PSA workstation KIRAP(Korea Integrated Reliability Analysis Code Package) for the PSA work. This report describes the procedures to perform accident sequence quantification, the method to use KIRAP`s cut set generator, and method to perform the accident sequence quantification with KIRAP. (author). 6 refs.

  5. Corporate Cost of Occupational Accidents

    DEFF Research Database (Denmark)

    Rikhardsson, Pall M.; Impgaard, M.

    2004-01-01

    method could be used in all of the companies without revisions. The evaluation of accident cost showed that 2/3 of the costs of occupational accidents are visible in the Danish corporate accounting systems reviewed while 1/3 is hidden from management view. The highest cost of occupational accidents......The systematic accident cost analysis (SACA) project was carried out during 2001 by The Aarhus School of Business and PricewaterhouseCoopers Denmark with financial support from The Danish National Working Environment Authority. Its focused on developing and testing a method for evaluating...... occupational costs of companies for use by occupational health and safety professionals. The method was tested in nine Danish companies within three different industry sectors and the costs of 27 selected occupational accidents in these companies were calculated. One of the main conclusions is that the SACA...

  6. Dose assessment in radiological accidents

    International Nuclear Information System (INIS)

    Donkor, S.

    2013-04-01

    The applications of ionizing radiation bring many benefits to humankind, ranging from power generation to uses in medicine, industry and agriculture. Facilities that use radiation source require special care in the design and operation of equipment to prevent radiation injury to workers or to the public. Despite considerable development of radiation safety, radiation accidents do happen. The purpose of this study is therefore to discuss how to assess doses to people who will be exposed to a range of internal and external radiation sources in the event of radiological accidents. This will go a long way to complement their medical assessment thereby helping to plan their treatment. Three radiological accidents were reviewed to learn about the causes of those accidents and the recommendations that were put in place to prevent recurrence of such accidents. Various types of dose assessment methods were discussed.(au)

  7. Severe accidents in nuclear reactors

    International Nuclear Information System (INIS)

    Ohai, Dumitru; Dumitrescu, Iulia; Tunaru, Mariana

    2004-01-01

    The likelihood of accidents leading to core meltdown in nuclear reactors is low. The consequences of such an event are but so severe that developing and implementing of adequate measures for preventing or diminishing the consequences of such events are of paramount importance. The analysis of major accidents requires sophisticated computation codes but necessary are also relevant experiments for checking the accuracy of the predictions and capability of these codes. In this paper an overview of the severe accidents worldwide with definitions, computation codes and relating experiments is presented. The experimental research activity of severe accidents was conducted in INR Pitesti since 2003, when the Institute jointed the SARNET Excellence Network. The INR activity within SARNET consists in studying scenarios of severe accidents by means of ASTEC and RELAP/SCDAP codes and conducting bench-scale experiments

  8. JCO criticality accident termination operation

    International Nuclear Information System (INIS)

    Kanamori, Masashi

    2001-12-01

    On September 30 at around 10:35 AM, criticality accident occurred at the JCO's conversion building in Tokai-mura. Since criticality accident had not been anticipated, neither devices for termination of criticality accident nor neutron detectors were available. Immediately after the information of the accident, our emergency staff (Japan Nuclear Cycle development institute staff) went to JCO site, to measure the intensity of neutrons and gammas. There were four main tasks, first one was to measure the radiation intensity, second one was to terminate the criticality accident, third one is to alert the residents surrounding the JCO site, fourth one is to evacuate the employees in the site. These tasks were successfully performed until October 1. This paper describes about how these operations were performed by the relevant staffs. (author)

  9. Homocysteine and cerebrovascular accidents.

    Science.gov (United States)

    Datta, Saikat; Pal, Salil K; Mazumdar, Hirak; Bhandari, Biswanath; Bhattacherjee, Sharmistha; Pandit, Sudipta

    2009-06-01

    Hyperhomocysteinaemia is rapidly emerging as an important risk factor for coronary artery disease, possibly because of its propensity to accelerate atherosclerosis. Whether it is also a risk factor for cerebrovascular accidents (CVA) is a matter of debate till now, as there are conflicting results of the various prospective studies. The present study was performed to correlate the levels of plasma homocysteine levels with that of ischaemic and haemorrhagic CVA. Forty-two cases of CVA were randomly selected over a period of one year, and their risk factors were assessed. It was observed that serum homocysteine levels were significantly raised in those with intracerebral infarcts when compared to those with intracerebral haemorrhage, although homocysteine levels didn't prove to be prognostically significant.

  10. Severe accident management. Prevention and Mitigation

    International Nuclear Information System (INIS)

    1992-01-01

    Effective planning for the management of severe accidents at nuclear power plants can produce both a reduction in the frequency of such accidents as well as the ability to mitigate their consequences if and when they should occur. This report provides an overview of accident management activities in OECD countries. It also presents the conclusions of a group of international experts regarding the development of accident management methods, the integration of accident management planning into reactor operations, and the benefits of accident management

  11. The Fukushima accident

    International Nuclear Information System (INIS)

    Loria Meneses, Luis Guillermo

    2011-01-01

    The accident happened on March 11, 2011 in the nuclear reactors at the Fukushima plant, Japan, is described. The reactors of the Fukushima plant have been power reactors. The electrical energy is produced by use of the heat released in the fission. Nuclear reactors were affected after of the power outage as a result of the earthquake and the tsunami, and this has kept in operation the refrigeration systems. The japanese reactors have been fission reactors and have used uranium 235 or plutonium 239 as fissionable material. The nuclear reactions of fission are explained. The control of the nuclear reactions at Fukushima was complicated by the decreased of the neutrons absorption and has produced more reactions, generating great amounts of heat. The steam contaminated with the products of fission is produced by to cool the reactor with water. The fissionable material released is dragged until the atmosphere. Radioactive contamination at sites near the reactor was covered in a zone of exclusion with a radius of 30 km. The effects of radioactive contamination in the zone of exclusion are mentioned. The radioactive material from Japan has traveled with the wind in direction toward the north pole. The radioactive cloud has continued until to reach the north Africa and south of Europe. The cloud has approximated to Costa Rica, but the activity of the material found has been less of 0,01 Bq/m3. The Centro de Investigacion en Ciencias Atomicas, Nucleares y Moleculares (Cicanum) has initiated the collection of soil samples, water and earth products to detect part of the radioactive material from the cloud. The Cicanum has had modern equipments to quantify the specific concentrations of radioactive isotope, alpha emitters, beta and gamma, in food, water and milk. The Cicanum has maintained the radiological surveillance of foods after the Chernobyl accident [es

  12. Three-dimensional transient cooling simulations of a portable electronic device using PCM (phase change materials) in multi-fin heat sink

    International Nuclear Information System (INIS)

    Wang, Yi-Hsien; Yang, Yue-Tzu

    2011-01-01

    Transient three-dimensional heat transfer numerical simulations were conducted to investigate a hybrid PCM (phase change materials) based multi-fin heat sink. Numerical computation was conducted with different amounts of fins (0 fin, 3 fins and 6 fins), various heating power level (2 W, 3 W and 4 W), different orientation tests (vertical/horizontal/slanted), and charge and discharge modes. Calculating time step (0.03 s, 0.05 s, and 0.07 s) size was discussed for transient accuracy as well. The theoretical model developed is validated by comparing numerical predictions with the available experimental data in the literature. The results showed that the transient surface temperatures are predicted with a maximum discrepancy within 10.2%. The operation temperature can be controlled well by the attendance of phase change material and the longer melting time can be conducted by using a multi-fin hybrid heat sink respectively. -- Highlights: → Electronic device cooling use phase change materials. → N-eicosane is adapted as phase change materials. → Present surface transient temperatures prediction error is within 10.2%. → Hybrid PCM-heat sink system provides stable operation temperature. → Orientation effects show independent on the phase change performance.

  13. Construction industry accidents in Spain.

    Science.gov (United States)

    Camino López, Miguel A; Ritzel, Dale O; Fontaneda, Ignacio; González Alcantara, Oscar J

    2008-01-01

    This paper analyzed industrial accidents that take place on construction sites and their severity. Eighteen variables were studied. We analyzed the influence of each of these with respect to the severity and fatality of the accident. This descriptive analysis was grounded in 1,630,452 accidents, representing the total number of accidents suffered by workers in the construction sector in Spain over the period 1990-2000. It was shown that age, type of contract, time of accident, length of service in the company, company size, day of the week, and the remainder of the variables under analysis influenced the seriousness of the accident. IMPACT ON INJURY PREVENTION: The results obtained show that different training was needed, depending on the severity of accidents, for different age, length of service in the company, organization of work, and time when workers work. The research provides an insight to the likely causes of construction injuries in Spain. As a result of the analysis, industries and governmental agencies in Spain can start to provide appropriate strategies and training to the construction workers.

  14. Contributing factors in construction accidents.

    Science.gov (United States)

    Haslam, R A; Hide, S A; Gibb, A G F; Gyi, D E; Pavitt, T; Atkinson, S; Duff, A R

    2005-07-01

    This overview paper draws together findings from previous focus group research and studies of 100 individual construction accidents. Pursuing issues raised by the focus groups, the accident studies collected qualitative information on the circumstances of each incident and the causal influences involved. Site based data collection entailed interviews with accident-involved personnel and their supervisor or manager, inspection of the accident location, and review of appropriate documentation. Relevant issues from the site investigations were then followed up with off-site stakeholders, including designers, manufacturers and suppliers. Levels of involvement of key factors in the accidents were: problems arising from workers or the work team (70% of accidents), workplace issues (49%), shortcomings with equipment (including PPE) (56%), problems with suitability and condition of materials (27%), and deficiencies with risk management (84%). Employing an ergonomics systems approach, a model is proposed, indicating the manner in which originating managerial, design and cultural factors shape the circumstances found in the work place, giving rise to the acts and conditions which, in turn, lead to accidents. It is argued that attention to the originating influences will be necessary for sustained improvement in construction safety to be achieved.

  15. International aspects of nuclear accidents

    International Nuclear Information System (INIS)

    Uematsu, K.

    1989-09-01

    The accident at Chernobyl revealed that there were shortcomings and gaps in the existing international mechanisms and brought home to governments the need for stronger measures to provide better protection against the risks of severe accidents. The main thrust of international co-operation with regard to nuclear safety issues is aimed at achieving a uniformly high level of safety in nuclear power plants through continuous exchanges of research findings and feedback from reactor operating experience. The second type of problem posed in the event of an accident resulting in radioactive contamination of several countries relates to the obligation to notify details of the circumstances and nature of the accident speedily so that the countries affected can take appropriate protective measures and, if necessary, organize mutual assistance. Giving the public accurate information is also an important aspect of managing an emergency situation arising from a severe accident. Finally, the confusion resulting from the unwarranted variety of protective measures implemented after the Chernobyl accident has highlighted the need for international harmonization of the principles and scientific criteria applicable to the protection of the public in the event of an accident and for a more consistent approach to emergency plans. The international conventions on third party liability in the nuclear energy sector (Paris/Brussels Conventions and the Vienna Convention) provide for compensation for damage caused by nuclear accidents in accordance with the rules and jurisdiction that they lay down. These provisions impose obligations on the operator responsible for an accident, and the State where the nuclear facility is located, towards the victims of damage caused in another country

  16. Accident Analysis and Highway Safety

    Directory of Open Access Journals (Sweden)

    Omar Noorliyana

    2017-01-01

    Full Text Available Since 2010, Federal Route FT050 (Jalan Batu Pahat-Kluang has undergone many changes, including the improvement of geometric features (i.e., construction of median, dedicated U-turns and additional lanes and upgrading the quality of the road surface. Unfortunately, even with these enhancements, accidents continue to occur along this route. This study covered both accident analysis and blackspot study. Accident point weightage was used to identify blackspot locations. The results reveal hazardous road locations and blackspot ranking along the route.

  17. Medical care of radiation accidents

    International Nuclear Information System (INIS)

    Nakao, Isamu

    1986-02-01

    This monograph, divided into six chapters, focuses on basic knowledge and medical strategies for radiation accidents. Chapters I to V deal with practice in emergency care for radiation exposure, covering 1) medical strategies for radiation accidents, 2) personnel dosimetry and monitoring, 3) nuclear facilities and their surrounding areas with the potential for creating radiation accidents, and emergency medical care for exposed persons, 4) emergency care procedures for radiation exposure and radioactive contamination, and 5) radiation hazards and their treatment. The last chapter provides some references. (Namekawa, K.)

  18. Judicial autopsy of radiation accidents

    International Nuclear Information System (INIS)

    Kannan, P.M.

    1990-01-01

    This paper discusses issues regarding the judicial autopsy of radiation accidents. In the litigation which follows a radiation accident, a claimant calls on the legal system to adjudicate a dispute. Scientific questions are thrust upon the court. The legal system (through attorneys for the parties) then invites scientists to assist the court in resolving such questions. The invitation, however, does not allow the scientist to bring along his full kit. Experimentation, such as repeating the accident with dosimeters to gather more accurate data, is generally not allowed. Also, the scientist must give up his practice of choosing which questions he will pursue

  19. A review of criticality accidents

    International Nuclear Information System (INIS)

    Stratton, W.R.; Smith, D.R.

    1989-03-01

    Criticality accidents and the characteristics of prompt power excursions are discussed. Forty-one accidental power transients are reviewed. In each case where available, enough detail is given to help visualize the physical situation, the cause or causes of the accident, the history and characteristics of the transient, the energy release, and the consequences, if any, to personnel and property. Excursions associated with large power reactors are not included in this study, except that some information on the major accident at the Chernobyl reactor in April 1986 is provided in the Appendix. 67 refs., 21 figs., 2 tabs

  20. The handling of radiation accidents

    International Nuclear Information System (INIS)

    1977-01-01

    The symposium was attended by 204 participants from 39 countries and 5 international organizations. Forty-two papers were presented in 8 sessions. The purpose of the meeting was to foster an exchange of experiences gained in establishing and exercising plans for mitigating the effects of radiation accidents and in the handling of actual accident situations. Only a small number of accidents were reported at the symposium, and this reflects the very high standards of safety that has been achieved by the nuclear industry. No accidents of radiological significance were reported to have occurred at commercial nuclear power plants. Of the accidents reported, industrial radiography continues to be the area in which most of the radiation accidents occur. The experience gained in the reported accident situations served to confirm the crucial importance of the prompt availability of medical and radiological services, particularly in the case of uptake of radioactive material, and emphasized the importance of detailed investigation into the causes of the accident in order to improve preventative measures. One of the principal themes of the symposium involved emergency procedures related to nuclear power plant accidents, and several papers defining the scope, progression and consequences of design base accidents for both thermal and fast reactor systems were presented. These were complemented by papers defining the resultant protection requirements that should be satisfied in the establishment of plans designed to mitigate the effects of the postulated accident situations. Several papers were presented describing existing emergency organizational arrangements relating both to specific nuclear power plants and to comprehensive national schemes, and a particularly informative session was devoted to the topic of training of personnel in the practical conduct of emergency arrangements. The general feeling of the participants was one of studied confidence in the competence and

  1. Underreporting of maritime accidents to vessel accident databases.

    Science.gov (United States)

    Hassel, Martin; Asbjørnslett, Bjørn Egil; Hole, Lars Petter

    2011-11-01

    Underreporting of maritime accidents is a problem not only for authorities trying to improve maritime safety through legislation, but also to risk management companies and other entities using maritime casualty statistics in risk and accident analysis. This study collected and compared casualty data from 01.01.2005 to 31.12.2009, from IHS Fairplay and the maritime authorities from a set of nations. The data was compared to find common records, and estimation of the true number of occurred accidents was performed using conditional probability given positive dependency between data sources, several variations of the capture-recapture method, calculation of best case scenario assuming perfect reporting, and scaling up a subset of casualty information from a marine insurance statistics database. The estimated upper limit reporting performance for the selected flag states ranged from 14% to 74%, while the corresponding estimated coverage of IHS Fairplay ranges from 4% to 62%. On average the study results document that the number of unreported accidents makes up roughly 50% of all occurred accidents. Even in a best case scenario, only a few flag states come close to perfect reporting (94%). The considerable scope of underreporting uncovered in the study, indicates that users of statistical vessel accident data should assume a certain degree of underreporting, and adjust their analyses accordingly. Whether to use correction factors, a safety margin, or rely on expert judgment, should be decided on a case by case basis. Copyright © 2011 Elsevier Ltd. All rights reserved.

  2. Accident response in France

    International Nuclear Information System (INIS)

    Duco, J.; L'Homme, A.; Queniart, D.

    1988-07-01

    French PWR power plant design relies basically on a deterministic approach. A probabilistic approach was introduced in France in the early seventies to define safety provisions against external impacts. In 1977 an overall safety objective was issued by the safety authority in terms of an upper probability limit for having unacceptable consequences. Additional measures were taken (the ''H'' operating procedures) to complement the automatic systems normally provided by the initial design, so as to safisfy the safety objective. The TMI-2 accident enhanced the interest in confused situations in which possible multiple equipment failure and/or unappropriate previous actions of the operators impede the implementation of any of the existing event-oriented procedures. In such situations, the objective becomes to avoid core-melt by any means available: this is the goal of the Ul symptom-oriented procedure. Whenever a core-melt occurs, the radioactive releases into the environment must be compatible with the feasibility of the off-site emergency plans; that means that for some hypothetical, but still conceivable scenarios, provisions have to be made to delay and limit the consequences of the loss of the containment: the U2, U4 and U5 ultimate procedures have been elaborated for that purpose. For the case of an emergency, a nationwide organization has been set up to provide the plant operator with a redundant technical expertise, to help him save his plant or mitigate the radiological consequences of a core-melt

  3. RENEB accident simulation exercise.

    Science.gov (United States)

    Brzozowska, Beata; Ainsbury, Elizabeth; Baert, Annelot; Beaton-Green, Lindsay; Barrios, Leonardo; Barquinero, Joan Francesc; Bassinet, Celine; Beinke, Christina; Benedek, Anett; Beukes, Philip; Bortolin, Emanuela; Buraczewska, Iwona; Burbidge, Christopher; De Amicis, Andrea; De Angelis, Cinzia; Della Monaca, Sara; Depuydt, Julie; De Sanctis, Stefania; Dobos, Katalin; Domene, Mercedes Moreno; Domínguez, Inmaculada; Facco, Eva; Fattibene, Paola; Frenzel, Monika; Monteiro Gil, Octávia; Gonon, Géraldine; Gregoire, Eric; Gruel, Gaëtan; Hadjidekova, Valeria; Hatzi, Vasiliki I; Hristova, Rositsa; Jaworska, Alicja; Kis, Enikő; Kowalska, Maria; Kulka, Ulrike; Lista, Florigio; Lumniczky, Katalin; Martínez-López, Wilner; Meschini, Roberta; Moertl, Simone; Moquet, Jayne; Noditi, Mihaela; Oestreicher, Ursula; Orta Vázquez, Manuel Luis; Palma, Valentina; Pantelias, Gabriel; Montoro Pastor, Alegria; Patrono, Clarice; Piqueret-Stephan, Laure; Quattrini, Maria Cristina; Regalbuto, Elisa; Ricoul, Michelle; Roch-Lefevre, Sandrine; Roy, Laurence; Sabatier, Laure; Sarchiapone, Lucia; Sebastià, Natividad; Sommer, Sylwester; Sun, Mingzhu; Suto, Yumiko; Terzoudi, Georgia; Trompier, Francois; Vral, Anne; Wilkins, Ruth; Zafiropoulos, Demetre; Wieser, Albrecht; Woda, Clemens; Wojcik, Andrzej

    2017-01-01

    The RENEB accident exercise was carried out in order to train the RENEB participants in coordinating and managing potentially large data sets that would be generated in case of a major radiological event. Each participant was offered the possibility to activate the network by sending an alerting email about a simulated radiation emergency. The same participant had to collect, compile and report capacity, triage categorization and exposure scenario results obtained from all other participants. The exercise was performed over 27 weeks and involved the network consisting of 28 institutes: 21 RENEB members, four candidates and three non-RENEB partners. The duration of a single exercise never exceeded 10 days, while the response from the assisting laboratories never came later than within half a day. During each week of the exercise, around 4500 samples were reported by all service laboratories (SL) to be examined and 54 scenarios were coherently estimated by all laboratories (the standard deviation from the mean of all SL answers for a given scenario category and a set of data was not larger than 3 patient codes). Each participant received training in both the role of a reference laboratory (activating the network) and of a service laboratory (responding to an activation request). The procedures in the case of radiological event were successfully established and tested.

  4. Accident risk. Chapter 5

    International Nuclear Information System (INIS)

    1978-01-01

    Following a historical introduction in which WASH-740, WASH-1400, Swedish, Finnish, Scandinavian, Netherlands and West German analyses are briefly presented, the concept of risk itself is discussed, distinguishing between objective and subjective aspects, and between voluntary and involuntary risk. Risk analysis is briefly described and an attempt made to define acceptable risk. In treating the safety philosophy of nuclear power plants the engineered safety precautions are presented. The numerical results of the analysis made for Norwegian conditions are presented and discussed. Underground siting, which has been much discussed in Norway is also treated, and emergency planning briefly discussed. The probability and consequences of core meltdown in a light water reactor are then discussed, and the possible faults leading to this, both internal, human errors and external impacts are analysed. The failure mechanisms in the containment building which could lead to the release of activity are discussed, followed by the dispersion of the activity and the health and economic consequences. The accidents at Wuergassen and Brown's Ferry are briefly described as examples. A brief discussion of nuclear insurance and nuclear law in Norway form the concluding sections. (JIW)

  5. Radioactivity control after Fukushima accident

    International Nuclear Information System (INIS)

    Vukovic, D.; Mitrovic, R.; Vicentijevic, M.; Pantelic, G.

    2011-01-01

    Fukushima nuclear accident has influence on more attention when radioactivity of fish were controlled. Sea fish, freshwater fish, fish products and fish flour were analysed ( 95 samples). All products were safe for use with radiation-hygienic aspects. [sr

  6. The Goiania accident - environmental survey

    International Nuclear Information System (INIS)

    Godoy, J.M.; Moreira, M.C.F.; Fonseca, E.S. da

    1997-01-01

    The survey methods applied during the Goiania accident could be considered complementary one to the other, and were able to give a clear picture about the contamination in the city to guide the further decontamination works. (author)

  7. Severe accident recriticality analyses (SARA)

    DEFF Research Database (Denmark)

    Frid, W.; Højerup, C.F.; Lindholm, I.

    2001-01-01

    with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality-both super-prompt power bursts and quasi steady-state power......Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies......, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g(-1), was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s(-1). In most cases, however, the predicted energy deposition was smaller, below...

  8. Multidisciplinary accident investigation : volume 2

    Science.gov (United States)

    1976-05-01

    The Task II final report for 1974 of the Multidisciplinary Accident Investigation : Team of the Maryland Medical-Legal Foundation, Inc. is presented. This report describes some preliminary findings emanating from a series of comprehensive, multivaria...

  9. Multidisciplinary accident investigation : volume 1

    Science.gov (United States)

    1976-09-01

    The final report of the Multidisciplinary Accident Investigation Team of the Maryland Medical-Legal Foundation, Inc. is presented. The report describes the methodology, results, discussions, conclusions and recommendations pertaining to the investiga...

  10. [Early management of cerebrovascular accidents].

    Science.gov (United States)

    Libot, Jérômie; Guillon, Benoit

    2013-01-01

    A cerebrovascular accident requires urgent diagnosis and treatment.The management of a stroke must be early and adapted in order to improve the overall clinical outcome and lower the risk of mortality.

  11. HANARO thermal hydraulic accident analysis

    Energy Technology Data Exchange (ETDEWEB)

    Park, Chul; Kim, Heon Il; Lee, Bo Yook; Lee, Sang Yong [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1996-06-01

    For the safety assessment of HANARO, accident analyses for the anticipated operational transients, accident scenarios and limiting accident scenarios were conducted. To do this, the commercial nuclear reactor system code. RELAP5/MOD2 was modified to RELAP5/KMRR; the thermal hydraulic correlations and the heat exchanger model was changed to incorporate HANARO characteristics. This report summarizes the RELAP/KMRR calculation results and the subchannel analyses results based on the RELAP/KMRR results. During the calculation, major concern was placed on the integrity of the fuel. For all the scenarios, the important accident analysis parameters, i.e., fuel centerline temperatures and the minimum critical heat flux ratio(MCHFR), satisfied safe design limits. It was verified, therefore, that the HANARO was safely designed. 21 tabs., 89 figs., 39 refs. (Author) .new.

  12. Three Mile Island Accident Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Three Mile Island Accident Data consists of mostly upper air and wind observations immediately following the nuclear meltdown occurring on March 28, 1979, near...

  13. Preparedness against nuclear power accidents

    International Nuclear Information System (INIS)

    1985-01-01

    This booklet contains information about the organization against nuclear power accidents, which exist in the four Swedish counties with nuclear power plants. It is aimed at classes 7-9 of the Swedish schools. (L.E.)

  14. 49 CFR 195.50 - Reporting accidents.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Reporting accidents. 195.50 Section 195.50 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... PIPELINE Annual, Accident, and Safety-Related Condition Reporting § 195.50 Reporting accidents. An accident...

  15. 28 CFR 301.106 - Repetitious accidents.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Repetitious accidents. 301.106 Section 301.106 Judicial Administration FEDERAL PRISON INDUSTRIES, INC., DEPARTMENT OF JUSTICE INMATE ACCIDENT COMPENSATION General § 301.106 Repetitious accidents. If an inmate worker is involved in successive accidents...

  16. 32 CFR 644.532 - Reporting accidents.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Reporting accidents. 644.532 Section 644.532... and Improvements § 644.532 Reporting accidents. Immediately upon receipt of information of an accident... that an accident has occurred, the former using command should be requested to send qualified explosive...

  17. 22 CFR 102.8 - Reporting accidents.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Reporting accidents. 102.8 Section 102.8... Accidents Abroad § 102.8 Reporting accidents. (a) To airline and Civil Aeronautics Administration... probably be the first to be informed of the accident, in which event he will be expected to report the...

  18. Prevention of radiation accidents and their consequences

    International Nuclear Information System (INIS)

    Khiski, J.

    1976-01-01

    Clearing out reasons for nuclear accidents enables to take effective measures to minimize them. The number of accidents in 1957 - 1974 is given. The frequency of accidents at various working places, while operating with various radioisotopes is presented. The analysis of accidents and the confirmation of these estimates can lead to the generalization of data and to the formulation of preventive measures [ru

  19. Accidents in making fireworks. Tapaturmat polttopuun teossa

    Energy Technology Data Exchange (ETDEWEB)

    Solmio, H

    1991-01-01

    The accidents and the trends in the number of accidents and their causes were analyzed in a study conducted by the Forestry Department of the Work Efficiency Institute. The study was funded by the Finnish Agricultural Enterpreneurs' Pension Fund (MELA). The study material was selected from MELA's accident stage work and cause code. Altogether, the material comprised the following accidents that occurred while making and using firewood: 671 accidents in 1987 and 596 accidents in 1988. The amount of accidents caused by the working environment and hand tools was clearly higher in 1987 than in 1988. The number of accidents occurred while chopping wood was 20 % higher in 1987 than in 1988. April was the most accident-prone month both in 1987 and in 1988. Chopping of firewood was the most dangerous work stage in terms of the number of accidents. In 1988, the number of accidents in chopping firewood was 336, in sawing using circular saw 97 cases and other mechanized chopping led to 93 accidents. Heating with wood caused 33 accidents. In 1988 there were 10 (2 %) accidents involving loss of limbs and 9 of them occurred in the mechanized chopping of firewood. Nine accidents of these involved the loss of one or more fingers. Serious accidents, leading to inability to work for more than 3 months, were most frequent in chopping and in storing firewood.

  20. Accidents at nuclear power plants

    International Nuclear Information System (INIS)

    Anon.

    1979-01-01

    The accidents which accurred at Wuergassen, Browns Ferry and Three Mile Island are each briefly described and discussed. The last is naturally treated in much more detail than the first two. Damage to the fuel elements is briefly considered and the release of fission products, radiation doses to the population and their expected consequences are discussed. The accidents are evaluated and related to risk evaluations, especially in WASH-1400. (JIW)

  1. JCO criticality accident termination operation

    OpenAIRE

    金盛 正至

    2010-01-01

    In 2001, we summarized the circumstances surrounding termination of the JCO criticality accident based on testimony in the Mito District Court on December 17, 2001. JCO was the company for uranium fuels production in Japan. That document was assembled based on actual testimony in the belief that a description of the work involved in termination of the accident would be useful in some way for preventing nuclear disasters in the future. This year is the tenth year of the JCO criticality acciden...

  2. Nuclear laws and radiologic accidents

    International Nuclear Information System (INIS)

    Frois, Fernanda

    1997-01-01

    Some aspects of the nuclear activities in Brazil, specially concerning the Goiania s accident are demonstrated using concepts from environmental and nuclear law. Nuclear and environmental competence, the impossibility of the states of making regional laws, as the lack of regulation about the nuclear waste, are discussed. The situation of Goiania when the accident happened, the present situation of the victims and the nuclear waste provisionally stored in Abadia de Goias is reported

  3. The IAEA Accident Management Programme

    International Nuclear Information System (INIS)

    Kabanov, L.; Jankowski, M.; Mauersberger, H.

    1993-01-01

    Accident prevention and mitigation programmes and the Emergency Response System (ERS) are important elements of the Agency's activities in the area of nuclear power plant (NPP) safety. Safety Codes and Guides on siting, design, quality assurance and the operation of NPPs have been produced and are used by NPP operating organizations. Nuclear safety evaluation services are provided by the IAEA. The Emergency Response System and the International Nuclear Event Scale (INES) have been developed. The framework for the development of an accident management programme has been set up. The main goal is to develop an Accident Management Manual to provide a systematic, structured approach to the development and implementation of an accident management programme at NPPs. An outline of the Manual has been distributed and the first draft is available. The component parts are: Co-ordinated research programmes (CRPs) on severe accident management and containment behaviour; the use of vulnerability analysis; mitigation of the effects of hydrogen, and generic symptom oriented emergency operating procedures. The IAEA provides guidance by the dissemination of information on methods for accident management; collates information on approaches in this field in different organizations and countries; and arranges exchange of experience and the promulgation of knowledge through the training of NPP managers and senior technical staff. (orig.)

  4. [Fatal occupational accidents in Lombardy].

    Science.gov (United States)

    Pianosi, G

    1995-01-01

    All fatal occupational accidents compensated in Lombardy from 1984 to 1989 were analyzed (1259 cases): significant differences between geographical distribution of fatal occupational accidents and workers were observed. Males accounted for about 95% of fatalities; an excess of cases was shown in both young and elderly workers. Death was the consequence of injuries involving most frequently the head, thorax and spinal cord. An excess of fatalities was observed in agriculture and, at a lower level, in manufacturing industries; small enterprises were involved in approximately 25% of fatalities occurring in the manufacturing industries and services. Employers were the victims of fatal accidents in 50% of cases in agriculture and in 70% of cases in craft industries. Construction, agriculture and transport accounted for about 50% of all fatalities. About 50% of fatal occupational accidents were related to vehicle use: the victim was the driver in the majority of cases, sometimes the victim was run over by a vehicle or fell from a vehicle. The results agree with some previous observations (e.g.: sex and age distribution; construction, agriculture and transport as working activities at high accident risk); but some original observations have emerged, in particular about the frequency of employers as victims and the role of vehicles in the genesis of fatal occupational accidents. If further studies confirm these latter observations, important developments could follow in preventive action design and implementation.

  5. CARNSORE: Hypothetical reactor accident study

    International Nuclear Information System (INIS)

    Walmod-Larsen, O.; Jensen, N.O.; Kristensen, L.; Meide, A.; Nedergaard, K.L.; Nielsen, F.; Lundtang Petersen, E.; Petersen, T.; Thykier-Nielsen, S.

    1984-06-01

    Two types of design-basis accident and a series of hypothetical core-melt accidents to a 600 MWe reactor are described and their consequences assessed. The PLUCON 2 model was used to calculate the consequences which are presented in terms of individual and collective doses, as well as early and late health consequences. The site proposed for the nucelar power station is Carnsore Point, County Wexford, south-east Ireland. The release fractions for the accidents described are those given in WASH-1400. The analyses are based on the resident population as given in the 1979 census and on 20 years of data from the meteorological stations at Rosslare Harbour, 8.5 km north of the site. The consequences of one of the hypothetical core-melt accidents are described in detail in a meteorological parametric study. Likewise the consequences of the worst conceivable combination of situations are described. Finally, the release fraction in one accident is varied and the consequences of a proposed, more probable ''Class 9 accident'' are presented. (author)

  6. The IAEA Accident Management Programme

    Energy Technology Data Exchange (ETDEWEB)

    Kabanov, L.; Jankowski, M.; Mauersberger, H. (International Atomic Energy Agency, Vienna (Austria))

    1993-02-01

    Accident prevention and mitigation programmes and the Emergency Response System (ERS) are important elements of the Agency's activities in the area of nuclear power plant (NPP) safety. Safety Codes and Guides on siting, design, quality assurance and the operation of NPPs have been produced and are used by NPP operating organizations. Nuclear safety evaluation services are provided by the IAEA. The Emergency Response System and the International Nuclear Event Scale (INES) have been developed. The framework for the development of an accident management programme has been set up. The main goal is to develop an Accident Management Manual to provide a systematic, structured approach to the development and implementation of an accident management programme at NPPs. An outline of the Manual has been distributed and the first draft is available. The component parts are: Co-ordinated research programmes (CRPs) on severe accident management and containment behaviour; the use of vulnerability analysis; mitigation of the effects of hydrogen, and generic symptom oriented emergency operating procedures. The IAEA provides guidance by the dissemination of information on methods for accident management; collates information on approaches in this field in different organizations and countries; and arranges exchange of experience and the promulgation of knowledge through the training of NPP managers and senior technical staff. (orig.).

  7. Reactor accidents and the environment

    International Nuclear Information System (INIS)

    Beattie, J.R.; Griffiths, R.F.; Kaiser, G.D.; Kinchin, G.H.

    1978-01-01

    This is a condensed version of a paper, entitled 'The Environmental Impact of Radioactive Releases from Accidents in Nuclear Power Reactors', by the authors, presented to the Nuclear Energy Panel of the International Atomic Energy Agency/United Nations Environmental Programme. Headings include - Effects of ionising radiation on man; number of deaths expected from leukaemia and other cancers; risk estimates for incidence of benign nodules and thyroid cancer; maximum permissible levels and emergency levels of radiation and radioactivity; ICRP recommended dose limits for members of the general public; atmospheric dispersion and modelling; ICRP emergency reference levels for 1 131 , Cs 137 , Ru 106 and Sr 90 ; environmental consequences of accidental releases from nuclear power reactors; environmental impact of accidents to Magnox gas-cooled reactors; environmental impact of accidents to advanced gas-cooled reactors; environmental impact of accidents to fast reactors; and nature of risks. consequences are examined in terms of early and late biological effects on man, and contamination of land areas. Serious accidents are of low probability of occurrence, and the risk of accidents to nuclear power reactors is estimated to be very small. 43 references. (U.K.)

  8. Learning from nuclear accident experience

    International Nuclear Information System (INIS)

    Vaurio, J.K.

    1984-01-01

    Statistical procedures are developed to estimate accident occurrence rates from historical event records, to predict future rates and trends, and to estimate the accuracy of the rate estimates and predictions. Maximum likelihood estimation is applied to several learning models, and results are compared to earlier graphical and analytical estimates. The models are based on (1) the cumulative number of operating years, (2) the cumulative number of plants built, and (3) accidents (explicitly), with the accident rate distinctly different before and after an accident. The statistical accuracies of the parameters estimated are obtained in analytical form using the Fisher information matrix. Using data on core damage accidents in electricity producing plants, it is estimated that the probability for a plant to have a serious flaw has decreased from 0.1 to 0.01 during the developmental phase of the nuclear industry. At the same time the equivalent frequency of accidents has decreased from 0.04 per reactor year to 0.0004 per reactor year, partly due to the increasing population of plants. 10 references, 7 figures, 2 tables

  9. JAERI's activities in JCO accident

    International Nuclear Information System (INIS)

    2000-09-01

    The Japan Atomic Energy Research Institute (JAERI) was actively involved in a variety of technical supports and cooperative activities, such as advice on terminating the criticality condition, contamination checks of the residents and consultation services for the residents, as emergency response actions to the criticality accident at the uranium processing facility operated by the JCO Co. Ltd., which occurred on September 30, 1999. These activities were carried out in collaborative ways by the JAERI staff from the Tokai Research Establishment, Naka Fusion Research Establishment, Oarai Research Establishment, and Headquarter Office in Tokyo. As well, the JAERI was engaged in the post-accident activities such as identification of accident causes, analyses of the criticality accident, and dose assessment of exposed residents, to support the Headquarter for Accident Countermeasures of the Science and Technology Agency (STA), the Accident Investigation Committee and the Health Control Committee of the Nuclear Safety Commission of Japan (NSC). This report compiles the activities, that the JAERI has conducted to date, including the discussions on measures for terminating the criticality condition, evaluation of the fission number, radiation monitoring in the environment, dose assessment, analyses of criticality dynamics. (author)

  10. Nuclear fuel cycle facility accident analysis handbook

    International Nuclear Information System (INIS)

    Ayer, J.E.; Clark, A.T.; Loysen, P.; Ballinger, M.Y.; Mishima, J.; Owczarski, P.C.; Gregory, W.S.; Nichols, B.D.

    1988-05-01

    The Accident Analysis Handbook (AAH) covers four generic facilities: fuel manufacturing, fuel reprocessing, waste storage/solidification, and spent fuel storage; and six accident types: fire, explosion, tornado, criticality, spill, and equipment failure. These are the accident types considered to make major contributions to the radiological risk from accidents in nuclear fuel cycle facility operations. The AAH will enable the user to calculate source term releases from accident scenarios manually or by computer. A major feature of the AAH is development of accident sample problems to provide input to source term analysis methods and transport computer codes. Sample problems and illustrative examples for different accident types are included in the AAH

  11. Radiological accidents: education for prevention and confrontation

    International Nuclear Information System (INIS)

    Cardenas Herrera, Juan; Fernandez Gomez, Isis Maria

    2008-01-01

    The purpose of this work is to train and inform on radiological accidents as a preventive measure to improve the people life quality. Radiological accidents are part of the events of technological origin which are composed of nuclear and radiological accidents. As a notable figure is determined that there have been 423 radiological accidents from 1944 to 2005 and among the causes prevail industrial accidents, by irradiations, medical accidents and of laboratories, among others. Latin American countries such as Argentina, Brazil, Mexico and Peru are some where most accidents have occurred by radioactivity. The radiological accidents can have sociological, environmental, economic, social and political consequences. In addition, there are scenarios of potential nuclear accidents and in them the potential human consequences. Also, the importance of the organization and planning in a nuclear emergency is highlighted. Finally, the experience that Cuba has lived on the subject of radiological accidents is described [es

  12. Accident tolerant fuel analysis

    International Nuclear Information System (INIS)

    2014-01-01

    Safety is central to the design, licensing, operation, and economics of Nuclear Power Plants (NPPs). Consequently, the ability to better characterize and quantify safety margin holds the key to improved decision making about light water reactor design, operation, and plant life extension. A systematic approach to characterization of safety margins and the subsequent margins management options represents a vital input to the licensee and regulatory analysis and decision making that will be involved. The purpose of the Risk Informed Safety Margin Characterization (RISMC) Pathway research and development (R&D) is to support plant decisions for risk-informed margins management by improving economics and reliability, and sustaining safety, of current NPPs. Goals of the RISMC Pathway are twofold: (1) Develop and demonstrate a risk-assessment method coupled to safety margin quantification that can be used by NPP decision makers as part of their margin recovery strategies. (2) Create an advanced ''RISMC toolkit'' that enables more accurate representation of NPP safety margin. In order to carry out the R&D needed for the Pathway, the Idaho National Laboratory is performing a series of case studies that will explore methods- and tools-development issues, in addition to being of current interest in their own right. One such study is a comparative analysis of safety margins of plants using different fuel cladding types: specifically, a comparison between current-technology Zircaloy cladding and a notional ''accident-tolerant'' (e.g., SiC-based) cladding. The present report begins the process of applying capabilities that are still under development to the problem of assessing new fuel designs. The approach and lessons learned from this case study will be included in future Technical Basis Guides produced by the RISMC Pathway. These guides will be the mechanism for developing the specifications for RISMC tools and for defining how plant

  13. Behavior of a PCM at Varying Heating Rates: Experimental and Theoretical Study with an Aim at Temperature Moderation in Radionuclide Concrete Encasements

    Science.gov (United States)

    Medved', Igor; Trník, Anton

    2018-07-01

    Phase-change materials (PCMs) can store/release thermal energy within a small temperature range. This is of interest in various industrial applications, for example, in civil engineering (heating/cooling of buildings) or cold storage applications. Another application may be the moderation of temperature increases in concrete encasements of radionuclides during their decay. The phase-change behavior of a material is determined by its heat capacity and the peak it exhibits near a phase change. We analyze the behavior of such peaks for a selected PCM at heating rates varying between 0.1°C\\cdot min^{-1} and 1°C\\cdot min^{-1}, corresponding in real situations to different decay rates of radionuclides. We show that experimentally measured peaks can be plausibly described by an equilibrium theory that enables us to calculate the latent heat and phase-change temperature from experimental data.

  14. The cost of nuclear accidents

    International Nuclear Information System (INIS)

    2015-01-01

    Proposed by a technical section of the SFEN, and based on a meeting with representatives of different organisations (OECD-NEA, IRSN, EDF, and European Nuclear Energy Forum), this publication addresses the economic consequences of a severe accident (level 6 or 7) within an electricity producing nuclear power plant. Such an assessment essentially relies on three pillars: release of radio-elements outside the reactor, the scenario of induced consequences, and the method of economic quantification. After a recall and a comment of safety arrangements, and of the generally admitted probability of such an accident, this document notices that several actors are concerned by nuclear energy and are trying to assess accident costs. The issue of how to assess a cost (or costs) of a nuclear accident is discussed: there are in fact several types of costs and consequences. Thus, some costs can be rather precisely quantified when some others can be difficult to assess or with uncertainty. The relevance of some cost categories appears to be a matter of discussion and one must not forget that consequences can occur on a long term. The need for methodological advances is outlined and three categories of technical objectives are identified for the assessment (efficiency of safety measures to be put forward to mitigate the risk via a better accident management, compensation of victims and nuclear civil responsibility, and comparison of electricity production sectors and assessment of externalisation to guide public choices). It is outlined that the impact of accidents depend on several factors, that the most efficient mean to limit consequences of accidents is of course to limit radioactive emissions

  15. Síntesis de 3-ciano-4-hidroxicumarina y análisis de su equilibrio tautomérico utilizando la Teoría del Funcional de la Densidad (DFT y el modelo de solvatación continua (PCM | Synthesis of 3-cyanohydroxycoumarin and analysis of its tautomeric equilibrium using Density Functional Theory (DFT and polarizable continuum model (PCM

    Directory of Open Access Journals (Sweden)

    Gustavo Cabrera

    2017-11-01

    Full Text Available The procedure for the synthesis of 3-cyano-4-hydroxycoumarin is presented along with the results from the analysis of its tautomeric equilibrium using Density Functional Theory (DFT and Polarizable Continuum Model (PCM. The geometry of the compounds was optimized with Gaussian 03 and from the resulting structures, a group of thermodynamic and kinetic parameters were determined. It was found that 3-cyano-4-hydroxycoumarin was the most stable tautomer, as was also shown by spectroscopic techniques. Other parameters, such as: transition state energy, equlibrium constant, kinetic constant, bond orders and bond angles, were also calculated.

  16. Accident prevention in power plants

    International Nuclear Information System (INIS)

    Steyrer, H.

    Large thermal power plants are insured to a great extent at the Industrial Injuries Insurance Institute of Instrument and Electric Engineering. Approximately 4800 employees are registered. The accident frequency according to an evaluation over 12 months lies around 79.8 per year and 1000 employees in fossil-fired power plants, around 34.1 per year and 1000 employees in nuclear power plants, as in nuclear power plants coal handling and ash removal are excluded. Injuries due to radiation were not registered. The crucial points of accidents are mechanical injuries received on solid, sharp-edged and pointed objects (fossil-fired power plants 28.6%, nuclear power plants 41.5%), stumbling, twisting or slipping (fossil-fired power plants 21.8%, nuclear power plants 19.5%) and injuries due to moving machine parts (only nuclear power plants 12.2%). However, accidents due to burns or scalds obtain with 4.2% and less a lower portion than expected. The accident statistics can explain this fact in a way that the typical power plant accident does not exist. (orig./GL) [de

  17. Industrial accidents triggered by lightning.

    Science.gov (United States)

    Renni, Elisabetta; Krausmann, Elisabeth; Cozzani, Valerio

    2010-12-15

    Natural disasters can cause major accidents in chemical facilities where they can lead to the release of hazardous materials which in turn can result in fires, explosions or toxic dispersion. Lightning strikes are the most frequent cause of major accidents triggered by natural events. In order to contribute towards the development of a quantitative approach for assessing lightning risk at industrial facilities, lightning-triggered accident case histories were retrieved from the major industrial accident databases and analysed to extract information on types of vulnerable equipment, failure dynamics and damage states, as well as on the final consequences of the event. The most vulnerable category of equipment is storage tanks. Lightning damage is incurred by immediate ignition, electrical and electronic systems failure or structural damage with subsequent release. Toxic releases and tank fires tend to be the most common scenarios associated with lightning strikes. Oil, diesel and gasoline are the substances most frequently released during lightning-triggered Natech accidents. Copyright © 2010 Elsevier B.V. All rights reserved.

  18. A CANDU Severe Accident Analysis

    International Nuclear Information System (INIS)

    Negut, Gheorghe; Catana, Alexandru; Prisecaru, Ilie

    2006-01-01

    As interest in severe accident studies has increased in the last years, we have developed a set of simple models to analyze severe accidents for CANDU reactors that should be integrated in the EU codes. The CANDU600 reactor uses natural uranium fuel and heavy water (D2O) as both moderator and coolant, with the moderator and coolant in separate systems. We chose to analyze accident development for a LOCA with simultaneous loss of moderator cooling and the loss of emergency core cooling system (ECCS). This type of accident is likely to modify the reactor geometry and will lead to a severe accident development. When the coolant temperatures inside a pressure tube reaches 10000 deg C, a contact between pressure tube and calandria tube occurs and the residual heat is transferred to the moderator. Due to the lack of cooling, the moderator eventually begins to boil and is expelled, through the calandria vessel relief ducts, into the containment. Therefore the calandria tubes (fuel channels) will be uncovered, then will disintegrate and fall down to the calandria vessel bottom. After all the quantity of moderator is vaporized and expelled, the debris will heat up and eventually boil. The heat accumulated in the molten debris will be transferred through the calandria vessel wall to the shield tank water, which normally surrounds the calandria vessel. The phenomena described above are modelled, analyzed and compared with the existing data. The results are encouraging. (authors)

  19. Accident knowledge and emergency management

    Energy Technology Data Exchange (ETDEWEB)

    Rasmussen, B; Groenberg, C D

    1997-03-01

    The report contains an overall frame for transformation of knowledge and experience from risk analysis to emergency education. An accident model has been developed to describe the emergency situation. A key concept of this model is uncontrolled flow of energy (UFOE), essential elements are the state, location and movement of the energy (and mass). A UFOE can be considered as the driving force of an accident, e.g., an explosion, a fire, a release of heavy gases. As long as the energy is confined, i.e. the location and movement of the energy are under control, the situation is safe, but loss of confinement will create a hazardous situation that may develop into an accident. A domain model has been developed for representing accident and emergency scenarios occurring in society. The domain model uses three main categories: status, context and objectives. A domain is a group of activities with allied goals and elements and ten specific domains have been investigated: process plant, storage, nuclear power plant, energy distribution, marine transport of goods, marine transport of people, aviation, transport by road, transport by rail and natural disasters. Totally 25 accident cases were consulted and information was extracted for filling into the schematic representations with two to four cases pr. specific domain. (au) 41 tabs., 8 ills.; 79 refs.

  20. The radiological accident in Cochabamba

    International Nuclear Information System (INIS)

    2004-07-01

    In April 2002 an accident involving an industrial radiography source containing 192 Ir occurred in Cochabamba, Bolivia, some 400 km from the capital, La Paz. A faulty radiography source container had been sent back to the headquarters of the company concerned in La Paz together with other equipment as cargo on a passenger bus. This gave rise to a potential for serious exposure for the bus passengers as well as for the company employees who were using and transporting the source. The Government of Bolivia requested the assistance of the IAEA under the terms of the Convention on Assistance in the Case of a Nuclear Accident or Radiological Emergency. The IAEA in response assembled and sent to Bolivia a team composed of senior radiation safety experts and radiation pathology experts from Brazil, the United Kingdom and the IAEA to investigate the accident. The IAEA is grateful to the Government of Bolivia for the opportunity to report on this accident in order to disseminate the valuable lessons learned and help prevent similar accidents in the future

  1. Accident knowledge and emergency management

    International Nuclear Information System (INIS)

    Rasmussen, B.; Groenberg, C.D.

    1997-03-01

    The report contains an overall frame for transformation of knowledge and experience from risk analysis to emergency education. An accident model has been developed to describe the emergency situation. A key concept of this model is uncontrolled flow of energy (UFOE), essential elements are the state, location and movement of the energy (and mass). A UFOE can be considered as the driving force of an accident, e.g., an explosion, a fire, a release of heavy gases. As long as the energy is confined, i.e. the location and movement of the energy are under control, the situation is safe, but loss of confinement will create a hazardous situation that may develop into an accident. A domain model has been developed for representing accident and emergency scenarios occurring in society. The domain model uses three main categories: status, context and objectives. A domain is a group of activities with allied goals and elements and ten specific domains have been investigated: process plant, storage, nuclear power plant, energy distribution, marine transport of goods, marine transport of people, aviation, transport by road, transport by rail and natural disasters. Totally 25 accident cases were consulted and information was extracted for filling into the schematic representations with two to four cases pr. specific domain. (au) 41 tabs., 8 ills.; 79 refs

  2. The Three Mile Island accident

    International Nuclear Information System (INIS)

    Zebroski, E.L.

    1980-01-01

    It is important that the causes of this accident (and other, similar accidents but with less dramatic consequences) are completely understood and that the role of every contributing factor is exactly determined in order to discuss modifications and to judge their relative importance and schedule in an objective way. If the role of the various factors contributing to an accident is not fully understood, there will always be a 'mythology' of prejudiced and highly simplified assumptions. The experience of failure analysis shows that the causes first assumed are hardly ever the right ones, and that in some major and complex cases even the second or third generation of assumed causes is wrong. (orig.) [de

  3. Severe accident management guidelines tool

    International Nuclear Information System (INIS)

    Gutierrez Varela, Javier; Tanarro Onrubia, Augustin; Martinez Fanegas, Rafael

    2014-01-01

    Severe Accident is addressed by means of a great number of documents such as guidelines, calculation aids and diagnostic trees. The response methodology often requires the use of several documents at the same time while Technical Support Centre members need to assess the appropriate set of equipment within the adequate mitigation strategies. In order to facilitate the response, TECNATOM has developed SAMG TOOL, initially named GGAS TOOL, which is an easy to use computer program that clearly improves and accelerates the severe accident management. The software is designed with powerful features that allow the users to focus on the decision-making process. Consequently, SAMG TOOL significantly improves the severe accident training, ensuring a better response under a real situation. The software is already installed in several Spanish Nuclear Power Plants and trainees claim that the methodology can be followed easier with it, especially because guidelines, calculation aids, equipment information and strategies availability can be accessed immediately (authors)

  4. Severe accident simulation at Olkiuoto

    Energy Technology Data Exchange (ETDEWEB)

    Tirkkonen, H.; Saarenpaeae, T. [Teollisuuden Voima Oy (TVO), Olkiluoto (Finland); Cliff Po, L.C. [Micro-Simulation Technology, Montville, NJ (United States)

    1995-09-01

    A personal computer-based simulator was developed for the Olkiluoto nuclear plant in Finland for training in severe accident management. The generic software PCTRAN was expanded to model the plant-specific features of the ABB Atom designed BWR including its containment over-pressure protection and filtered vent systems. Scenarios including core heat-up, hydrogen generation, core melt and vessel penetration were developed in this work. Radiation leakage paths and dose rate distribution are presented graphically for operator use in diagnosis and mitigation of accidents. Operating on an graphically for operator use in diagnosis and mitigation of accidents. Operating on an 486 DX2-66, PCTRAN-TVO achieves a speed about 15 times faster than real-time. A convenient and user-friendly graphic interface allows full interactive control. In this paper a review of the component models and verification runs are presented.

  5. Containment integrity analysis under accidents

    International Nuclear Information System (INIS)

    Lin Chengge; Zhao Ruichang; Liu Zhitao

    2010-01-01

    Containment integrity analyses for current nuclear power plants (NPPs) mainly focus on the internal pressure caused by design basis accidents (DBAs). In addition to the analyses of containment pressure response caused by DBAs, the behavior of containment during severe accidents (SAs) are also evaluated for AP1000 NPP. Since the conservatism remains in the assumptions,boundary conditions and codes, margin of the results of containment integrity analyses may be overestimated. Along with the improvements of the knowledge to the phenomena and process of relevant accidents, the margin overrated can be appropriately reduced by using the best estimate codes combined with the uncertainty methods, which could be beneficial to the containment design and construction of large passive plants (LPP) in China. (authors)

  6. Patient treatment in radiation accidents

    International Nuclear Information System (INIS)

    Tanum, G.; Bruland, Oe.S.; Hjelle, D.; Reitan, J.B.

    1999-01-01

    Accidental human injury due to ionizing radiation is rare. Industrial accidents are comparatively the most common. Life saving procedures should always have priority to any concern about radiation injury or contamination. The personal risks for emergency medial personnel is negligible when simple measures are taken. Repeated clinical examinations and blood lymphocyte counts should be performed on all patients with suspected radiation injury to allow a diagnosis. The radiation syndrome develops within days or weeks depending on total radiation dose, dose rate and dose distribution. Damage to the bone marrow and gut are the most important. Local radiation injuries to the hands are common in industrial accidents. The Norwegian Radiation Protection Authority should always be called when a potential ionizing radiation accident takes place within Norway

  7. Action in case of accident

    International Nuclear Information System (INIS)

    Matijasic, A.

    1961-01-01

    This report describes the radiation accidents that occurred in the Institute, causes of these accidents and actions undertaken to eliminate the consequences as well as losses and cost estimated. The accidents were as follows: explosion of the uranium mixture; contamination due to spill of P 32 ; contamination due to spilling of Sr 89 solution; spilling of I 131 in the cell for radioactive iodine production; contamination of the floor by P 32 ; contamination of the platform below the water shield at the RA reactor and during cleaning of the vertical channels; contamination due to spilling of Sr 89 solution; contamination of cells for I 131 and P 32 and the cell for isotopes packaging; contamination of the floor by non-identified isotope mixture; contamination of the cell for I'1 31 production by irradiated Tl powder; contamination by La 140 powder; contamination of the cell for isotopes packaging

  8. Nuclear law and radiological accidents

    International Nuclear Information System (INIS)

    Frois, F.

    1998-01-01

    Nuclear activities in Brazil, and particularly the radiological accident of Goiania, are examined in the light of the environmental and nuclear laws of Brazil and the issue of responsibility. The absence of legislation covering radioactive wastes as well as the restrictions on Brazilian States to issue regulations covering nuclear activities are reviewed. The radiological accident and its consequences, including the protection and compensation of the victims, the responsibility of the shareholders of the Instituto Goiano de Radioterapia, operator of the radioactive source, the provisional storage and the final disposal at Abadia de Goias of the radioactive waste generated by the accident are reviewed. Finally, nuclear responsibility, the inapplicability of the Law 6453/77 which deals with nuclear damages, and the state liability regime are analysed in accordance with the principles of the Brazilian Federal Constitution. (author)

  9. JCO criticality accident termination operation

    International Nuclear Information System (INIS)

    Kanamori, Masashi

    2010-07-01

    In 2001, we summarized the circumstances surrounding termination of the JCO criticality accident based on testimony in the Mito District Court on December 17, 2001. JCO was the company for uranium fuels production in Japan. That document was assembled based on actual testimony in the belief that a description of the work involved in termination of the accident would be useful in some way for preventing nuclear disasters in the future. The description focuses on the witness' own behavior, and what he saw and heard, and thus is written from the perspective of action by one individual. This was done simply because it was easier for the witness to write down his memories as he remembers them. Description of the activities of other organizations and people is provided only as necessary, to ensure that consistency in the descriptive approach is not lost. The essentials of this report were rewritten as a third-person objective description in the summary of the report by the Atomic Energy Society of Japan (AESJ). Since then, comments have been received from sources such as former members of the Nuclear Safety Commission (Dr. Kenji Sumita and Dr. Akira Kanagawa), concerned parties from the former Science and Technology Agency, and reports from the JCO Criticality Accident Investigation Committee of the AESJ, and thus this report was rewritten to correct incorrect information, and add material where that was felt to be necessary. This year is the tenth year of the JCO criticality accident. To mark this occasion we have decided to translate the record of what occurred at the accident site into English so that more people can draw lessons from this accident. This report is an English version of JAEA-Technology 2009-073. (author)

  10. Severe accident source term reassessment

    International Nuclear Information System (INIS)

    Hazzan, M.J.; Gardner, R.; Warman, E.A.; Jacobs, S.B.

    1987-01-01

    This paper summarizes the status of the reassessment of severe reactor accident source terms, which are defined as the quantity, type, and timing of fission product releases from such accidents. Concentration is on the major results and conclusions of analyses with modern methods for both pressurized water reactors (PWRs) and boiling water reactors (BWRs), and the special case of containment bypass. Some distinctions are drawn between analyses for PWRs and BWRs. In general, the more the matter is examined, the consequences, or probability of serious consequences, seem to be less. (author)

  11. Civil liability concerning nuclear accidents

    International Nuclear Information System (INIS)

    Anon.

    2013-01-01

    France and the USA wish to cooperate in order to promote an international regime of civil liability in order to give a fair compensation to victims of nuclear accidents as it is recommended by IAEA. On the other hand the European Commission has launched a consultation to see the necessity or not to harmonize all the civil liability regimes valid throughout Europe. According to the Commission the potential victims of nuclear accidents would not receive equal treatment at the European scale in terms of insurance cover and compensation which might distort competition in the nuclear sector. (A.C.)

  12. The nature of reactor accidents

    International Nuclear Information System (INIS)

    Domaratzki, Z.; Campbell, F.R.; Atchison, R.J.

    1981-01-01

    Reactor accidents are events which result in the release of radioactive material from a nuclear power plant due to the failure of one or more critical components of that plant. The failures, depending on their number and type, can result in releases whose consequences range from negligible to catastrophic. By way of examples, this paper describes four specific accidents which cover this range of consequence: failure of a reactor control system, loss of coolant, loss of coolant with impaired containment, and reactor core meltdown. For each a possible sequence of events and an estimate of the expected frequency are presented

  13. Computerized accident management support system: development for severe accident management

    International Nuclear Information System (INIS)

    Garcia, V.; Saiz, J.; Gomez, C.

    1998-01-01

    The activities involved in the international Halden Reactor Project (HRP), sponsored by the OECD, include the development of a Computerized Accident Management Support System (CAMS). The system was initially designed for its operation under normal conditions, operational transients and non severe accidents. Its purpose is to detect the plant status, analyzing the future evolution of the sequence (initially using the APROS simulation code) and the possible recovery and mitigation actions in case of an accident occurs. In order to widen the scope of CAMS to severe accident management issues, the integration of the MAAP code in the system has been proposed, as the contribution of the Spanish Electrical Sector to the project (with the coordination of DTN). To include this new capacity in CAMS is necessary to modify the system structure, including two new modules (Diagnosis and Adjustment). These modules are being developed currently for Pressurized Water Reactors and Boiling Water REactors, by the engineering of UNION FENOSA and IBERDROLA companies (respectively). This motion presents the characteristics of the new structure of the CAMS, as well as the general characteristics of the modules, developed by these companies in the framework of the Halden Reactor Project. (Author)

  14. [Diving accidents. Emergency treatment of serious diving accidents].

    Science.gov (United States)

    Schröder, S; Lier, H; Wiese, S

    2004-11-01

    Decompression injuries are potentially life-threatening incidents mainly due to a rapid decline in ambient pressure. Decompression illness (DCI) results from the presence of gas bubbles in the blood and tissue. DCI may be classified as decompression sickness (DCS) generated from the liberation of gas bubbles following an oversaturation of tissues with inert gas and arterial gas embolism (AGE) mainly due to pulmonary barotrauma. People working under hyperbaric pressure, e.g. in a caisson for general construction under water, and scuba divers are exposed to certain risks. Diving accidents can be fatal and are often characterized by organ dysfunction, especially neurological deficits. They have become comparatively rare among professional divers and workers. However, since recreational scuba diving is gaining more and more popularity there is an increasing likelihood of severe diving accidents. Thus, emergency staff working close to areas with a high scuba diving activity, e.g. lakes or rivers, may be called more frequently to a scuba diving accident. The correct and professional emergency treatment on site, especially the immediate and continuous administration of normobaric oxygen, is decisive for the outcome of the accident victim. The definitive treatment includes rapid recompression with hyperbaric oxygen. The value of adjunctive medication, however, remains controversial.

  15. How to reduce the number of accidents

    CERN Multimedia

    2012-01-01

    Among the safety objectives that the Director-General has established for CERN in 2012 is a reduction in the number of workplace accidents.   The best way to prevent workplace accidents is to learn from experience. This is why any accident, fire, instance of pollution, or even a near-miss, should be reported using the EDH form that can be found here. All accident reports are followed up. The departments investigate all accidents that result in sick leave, as well as all the more common categories of accidents at CERN, essentially falls (slipping, falling on stairs, etc.), regardless of whether or not they lead to sick leave. By studying the accident causes that come to light in this way, it is possible to take preventive action to avoid such accidents in the future. If you have any questions, the HSE Unit will be happy to answer them. Contact us at safety-general@cern.ch. HSE Unit

  16. Pedestrian injury causation study (pedestrian accident typing)

    Science.gov (United States)

    1982-08-01

    A new computerized pedestrian accident typing procedure was tested on 1,997 cases from the Pedestrian Injury Causation Study (PICS). Two coding procedures were used to determine the effects of quantity and quality of information on accident typing ac...

  17. Lessons of the radiological accident in Goiania

    International Nuclear Information System (INIS)

    Alves, R.N.; Xavier, A.M.; Heilbron, P.F.L.

    1998-01-01

    On the basis of the lessons teamed from the radiological accident of Goiania, actions are described which a nuclear regulatory body should undertake while responding to an accident of this nature. (author)

  18. Socioeconomic consequences of nuclear reactor accidents

    International Nuclear Information System (INIS)

    Tawil, J.J.; Callaway, J.W.; Coles, B.L.; Cronin, F.J.; Currie, J.W.; Imhoff, K.L.; Lewis, P.M.; Nesse, R.J.; Strenge, D.L.

    1984-06-01

    This report identifies and characterizes the off-site socioeconomic consequences that would likely result from a severe radiological accident at a nuclear power plant. The types of impacts that are addressed include economic impacts, health impacts, social/psychological impacts and institutional impacts. These impacts are identified for each of several phases of a reactor accident - from the warning phase through the post-resettlement phase. The relative importance of the impact during each accident phase and the degree to which the impact can be predicted are indicated. The report also examines the methods that are currently used for assessing nuclear reactor accidents, including development of accident scenarios and the estimating of socioeconomic accident consequences with various models. Finally, a critical evaluation is made regarding the use of impact analyses in estimating the contribution of socioeconomic consequences to nuclear accident reactor accident risk. 116 references, 7 figures, 15 tables

  19. Trucks involved in fatal accidents factbook 2008.

    Science.gov (United States)

    2011-03-01

    This document presents aggregate statistics on trucks involved in traffic accidents in 2008. The : statistics are derived from the Trucks Involved in Fatal Accidents (TIFA) file, compiled by the : University of Michigan Transportation Research Instit...

  20. Buses involved in fatal accidents factbook 2007

    Science.gov (United States)

    2010-03-01

    This document presents aggregate statistics on buses involved in traffic accidents in 2007. The : statistics are derived from the Buses Involved in Fatal Accidents (BIFA) file, compiled by the : University of Michigan Transportation Research Institut...

  1. Trucks involved in fatal accidents factbook 2007.

    Science.gov (United States)

    2010-01-01

    This document presents aggregate statistics on trucks involved in traffic accidents in 2007. The : statistics are derived from the Trucks Involved in Fatal Accidents (TIFA) file, compiled by the : University of Michigan Transportation Research Instit...

  2. Road Accident Trends in Africa and Europe

    DEFF Research Database (Denmark)

    Jørgensen, N O

    1997-01-01

    The paper decribes trends and suggests prediction models for accident risks in African and European countries......The paper decribes trends and suggests prediction models for accident risks in African and European countries...

  3. Consequences of the Chernobyl accident

    International Nuclear Information System (INIS)

    Gerzabek, M.H.

    1990-10-01

    A collection of three papers about the fallout in Austria from the 1986 Chernobyl reactor accident is given: 1. An overview of the research projects in Austria; 2. On the transfer into and uptake by crops and animal fodder; 3. On the reduction of cesium concentration in food. 18 tabs., 21 figs., 69 refs

  4. Probabilistic studies of accident sequences

    International Nuclear Information System (INIS)

    Villemeur, A.; Berger, J.P.

    1986-01-01

    For several years, Electricite de France has carried out probabilistic assessment of accident sequences for nuclear power plants. In the framework of this program many methods were developed. As the interest in these studies was increasing and as adapted methods were developed, Electricite de France has undertaken a probabilistic safety assessment of a nuclear power plant [fr

  5. The Physics of Traffic Accidents

    Science.gov (United States)

    Knight, Peter

    1975-01-01

    Shows how physics can be used to analyze and prevent traffic accidents by determining critical speeds on curves, the behavior of motor cycles and stability of articulated vehicles, and the visibility that is needed to make a minor road junction safe. (MLH)

  6. CINETHICA - Core accident analysis code

    International Nuclear Information System (INIS)

    Nakata, H.

    1989-10-01

    A computer program for nuclear accident analysis has been developed based on the point-kinetics approximation and one-dimensional heat transfer model for reactivity feedback calculation. Hansen's method/1/ were used for the kinetics equation solution and explicit Euler method were adopted for the thermohidraulic equations. The results were favorably compared to those from the GAPOTKIN Code/2/. (author) [pt

  7. Accident consequence assessment code development

    International Nuclear Information System (INIS)

    Homma, T.; Togawa, O.

    1991-01-01

    This paper describes the new computer code system, OSCAAR developed for off-site consequence assessment of a potential nuclear accident. OSCAAR consists of several modules which have modeling capabilities in atmospheric transport, foodchain transport, dosimetry, emergency response and radiological health effects. The major modules of the consequence assessment code are described, highlighting the validation and verification of the models. (author)

  8. Reactor accidents of four decades

    International Nuclear Information System (INIS)

    Szabo, Z.

    1982-11-01

    The report covers the period between 1942 and June 30, 1982. A detailed description and a comparative analysis of reactor accidents and chemical-processing-plant excursions are presented. The analysis takes into account the following points: causes (design, maintenance, operation); events (initiating event and sequence of events); consequences (environmental impacts, personnel effects and equipment damages). (author)

  9. Crime, accidents and social control

    NARCIS (Netherlands)

    Junger, Marianne; Terlouw, Gert-Jan; van der Heijden, Peter G.M.

    1995-01-01

    This paper addresses to questions. (1) Is there a demonstrable relation between accidents and crime, does this relation hold for each type of crime and each means of transport, and does it subsist after controlling for age and gender? (2) Can social control theory explain involvements in both

  10. Accident considerations in LMFBR design

    International Nuclear Information System (INIS)

    Simpson, D.E.; Alter, H.; Fauske, H.K.; Hikido, K.; Keaten, R.W.; Stevenson, M.G.; Strawbridge, L.

    1975-12-01

    LMFBR safety design criteria are discussed from the standpoints of accident severity classification and damage criteria, and the following design events are considered: fuel failure propagation, reactivity addition faults, heat transport system events, steam generator faults, sodium spills, fuel handling and storage faults, and external events

  11. Standby after the Chernobyl accident

    International Nuclear Information System (INIS)

    1987-09-01

    The report is an investigation concerning strandby and actions by SKI (Swedish Nuclear Power Inspectorate) and SSI (National Institute of Radiation Protection) due to the Chernobyl reactor accident. It consists of a final report and two appendices. The final report is divided into two parts: 'I: Facts' and 'II: Analyzes'. 'Facts': The Swedish model for information: radio, press. Basic knowledge about ionizing radiation in the society. Resources for information. Need for information. Message forms for information. Announcements from the authorities in TV, radio, press, meeting, advertisements. Statements concerning the reactor accident and its consequences in Swedish mass media. How did the public recieve the information? 'Analyzis': Information responsibilities and policies. SSI information activities concerning radiologic accidents, conditions, methods and resources. Ditto for SKI, Swedish National Food Administration and the National Board of Agriculture. Appendix I: Information from authorities in the press three weeks after the Chernobyl accident: The material and the methods. The acute phase, the adoptation phase, the extension of the persective. What is said about the authorities in connection with Chernobyl? Appendix II: The fallout from Chernobyl, the authorities and the media coverage: The nationwide, regional and local coverage from radio and television. Ditto from the press. Topic and problem areas in reporting. Instructions from the authorities in media. Contribution in the media from people representing the authorities. Fallout in a chronologic perspective. (L.F.)

  12. New technology for accident prevention

    Energy Technology Data Exchange (ETDEWEB)

    Byne, P. [Shiftwork Solutions, Vancouver, BC (Canada)

    2006-07-01

    This power point presentation examined the effects of fatigue in the workplace and presented 3 technologies designed to prevent or monitor fatigue. The relationship between mental fatigue, circadian rhythms and cognitive performance was explored. Details of vigilance related degradations in the workplace were presented, as well as data on fatigue-related accidents and a time-line of meter-reading errors. It was noted that the direct cause of the Exxon Valdez disaster was sleep deprivation. Fatigue related accidents during the Gulf War were reviewed. The effects of fatigue on workplace performance include impaired logical reasoning and decision-making; impaired vigilance and attention; slowed mental operations; loss of situational awareness; slowed reaction time; and short cuts and lapses in optional or self-paced behaviours. New technologies to prevent fatigue-related accidents include (1) the driver fatigue monitor, an infra-red camera and computer that tracks a driver's slow eye-lid closures to prevent fatigue related accidents; (2) a fatigue avoidance scheduling tool (FAST) which collects actigraphs of sleep activity; and (3) SAFTE, a sleep, activity, fatigue and effectiveness model. refs., tabs., figs.

  13. The radiological accident in Istanbul

    International Nuclear Information System (INIS)

    2000-01-01

    The use of radioactive materials offers a wide range of benefits throughout the world in medicine, research and industry. Precautions are, however, necessary in order to limit the exposure of persons to the radiation that is emitted. Where the amount of radioactive material is substantial, as in the case of radiotherapy sources or industrial radiography sources, extreme care is necessary to prevent accidents which may have severe consequences. Nevertheless, in spite of the precautions taken, accidents with radiation sources continue to occur, albeit infrequently. As part of its subprogramme on the safety of radiation sources, the IAEA conducts follow-up reviews of such serious accidents to give an account of their circumstances and of the medical aspects, from which organizations with responsibilities for radiation protection and the safety of sources may learn. A serious radiological accident occurred in Istanbul, Turkey, in December 1998 and January 1999 when two packages used to transport 60 Co teletherapy sources were sold as scrap metal. The persons who purchased the two packages opened them and broke open the shielded containers, thereby unknowingly exposing themselves and several others to radiation from at least one unshielded 60 Co source. The persons who dismantled the containers suffered from acute radiation syndrome. The accident came to the attention of the relevant national authority when a doctor who had examined the victims reported that he suspected the possibility of radiation exposure. The national authorities identified other individuals who might have undergone acute radiation exposures, and a total of 18 persons (including seven children) were admitted to hospital. Of these, ten adults exhibited clinical signs and symptoms of acute radiation exposure. Under the Convention on Assistance in the Case of a Nuclear Accident or Radiological Emergency, the Turkish authorities requested assistance from the IAEA in terms of advice on the medical

  14. Trismus: An unusual presentation following road accident

    Directory of Open Access Journals (Sweden)

    Thakur Jagdeep

    2007-01-01

    Full Text Available Trismus due to trauma usually follows road accidents leading to massive faciomaxillary injury. In the literature there is no report of a foreign body causing trismus following a road accident, this rare case is an exception. We present a case of isolated presentation of trismus following a road accident. This case report stresses on the thorough evaluation of patients presenting with trismus following a road accident.

  15. Assessment of Mobile Accident Response Capability

    International Nuclear Information System (INIS)

    1983-03-01

    This report presents the results of a DOE-sponsored assessment of nuclear accident response resources. It identifies the mobile resources that could be required to respond to different types of nuclear accidents including major ones like TMI-2, identifies the resources currently available and makes recommendations for the design and construction of additional mobile accident response resources to supplement those already in existence. This project is referred to as the Mobile Accident Response Capability (MARC) program

  16. The radiological accident in Lilo

    International Nuclear Information System (INIS)

    2000-01-01

    The use of radioactive materials offers a wide range of benefits throughout the world in medicine, research and industry. Precautions are, however, necessary in order to limit the exposure of persons to the radiation that is emitted. Where the amount of radioactive material is substantial, such as with sources used in radiotherapy or industrial radiography, extreme care is necessary to prevent accidents that may result in severe consequences for the affected individuals. Nevertheless, in spite of the precautions taken, accidents with radiation sources continue to occur, albeit infrequently. As part of its activities dealing with the safety of radiation sources, the IAEA follows up severe accidents with a view to providing an account of their circumstances and the medical aspects from which those organizations with responsibilities for radiation protection and the safety of sources may learn. A serious radiological accident occurred in Peru in February 1999 when a welder picked up an 192 Ir industrial radiography source and put it in his pocket for several hours. This resulted in his receiving a high radiation dose that necessitated the amputation of one leg. His wife and children were also exposed, but to a much lesser extent. The Peruvian authorities requested assistance from the IAEA in obtaining advice on medical treatment. They also agreed to assist the IAEA with the subsequent review of the circumstances surrounding the accident. The IAEA is grateful to the Instituto Peruano de Energia Nuclear for its willingness to assist in the reparation of this report and, thereby, share its experience with other Member States

  17. Planning for large-scale accidents: learning from the Three Mile Island accident

    International Nuclear Information System (INIS)

    Fischer, D.W.

    1981-01-01

    Decision-making issues raised at the Three Mile Island nuclear accident in Pennsylvania are explored. The organizations involved, their interconnections, and decisions are described. The underlying issues bearing on allocation of effort to pre-accident planning and actual accident responses are also noted. Finally, a framework from this effort is used for guiding the planning of operations for future accidents. (author)

  18. Detection and analysis of accident black spots with even small accident figures.

    NARCIS (Netherlands)

    Oppe, S.

    1982-01-01

    Accident black spots are usually defined as road locations with high accident potentials. In order to detect such hazardous locations we have to know the probability of an accident for a traffic situation of some kind, or the mean number of accidents for some unit of time. In almost all procedures

  19. Use of PSA to support accident management at NPPs

    International Nuclear Information System (INIS)

    Gomez Cobo, A.

    1997-01-01

    The presentation discusses the following: Overview of PSA level 2; Introduction: Framework; Accident Progression Phenomena in the Confinement/containment; Severe Accident Sequences; Examples; Results and Insights. Accident Management: Concepts; Process; Use of PSA to support Accident; Management

  20. Intersection layout, traffic volumes and accidents.

    NARCIS (Netherlands)

    Poppe, F.

    1988-01-01

    This paper reports on the accident research carried out as a part of a large project started in 1983. For this accident research an inventory was made of a large number of intersections.Recorded were layout features, accident data and estimates of traffic volumes. Attention will be given to the

  1. Nuclear accidents. Three mile Island (United States)

    International Nuclear Information System (INIS)

    Duco, J.

    2004-01-01

    This paper describes the accident of Three Miles Island power plant which occurred the 28 march 1979 in the United States. The accident scenario, the consequences and the reactor core and vessel, after the accident, are analyzed. (A.L.B.)

  2. Report about the radiological accident in Goiania

    International Nuclear Information System (INIS)

    Schrimer, H.P.; Gomes, C.A.; Recio, J.C.A.

    1997-01-01

    This work reports the activities developed by the technical groups who worked during the radiological accident in Goiania, held on September 1997. Several aspects of the accident are described. The final solution for the disposal of the radioactive wastes generated during the accident is presented, according to the Brazilian waste management policy. (author)

  3. School Bus Accidents and Driver Age.

    Science.gov (United States)

    McMichael, Judith

    The study examines the rates and types of school bus accidents according to the age of the school bus driver. Accident rates in North Carolina for the school year 1971-72 were analyzed using three sources of data: accident reports, driver and mileage data, and questionnaires administered to a sample of school bus drivers. Data were obtained on…

  4. 48 CFR 836.513 - Accident prevention.

    Science.gov (United States)

    2010-10-01

    ... CATEGORIES OF CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 836.513 Accident... solicitations and contracts for construction that contain the clause at FAR 52.236-13, Accident Prevention. ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Accident prevention. 836...

  5. 48 CFR 36.513 - Accident prevention.

    Science.gov (United States)

    2010-10-01

    ... CATEGORIES OF CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 36.513 Accident prevention. (a) The contracting officer shall insert the clause at 52.236-13, Accident Prevention, in... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Accident prevention. 36...

  6. 48 CFR 636.513 - Accident prevention.

    Science.gov (United States)

    2010-10-01

    ... CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Contract Clauses 636.513 Accident prevention. (a) In... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Accident prevention. 636... contracting activities shall insert DOSAR 652.236-70, Accident Prevention, in lieu of FAR clause 52.236-13...

  7. Accidents in chemical industry: are they foreseeable?

    NARCIS (Netherlands)

    Sonnemans, P.J.M.; Körvers, P.M.W.

    2006-01-01

    Accidents recur,’ which is what Kletz [Kletz T. (1993). Lessons from disasters, how organisations have no memory and accidents recur. UK: Institution of Chemical Engineers] wrote in 1993. Indeed, despite all measures taken accidents may re-occur, but ‘disruptions’ in a process reoccur much more

  8. Epidemiology o.f· Traffic Accidents

    African Journals Online (AJOL)

    Accidents. An analysis of some 2 100 fatal traffic accidents gave the following results: males-79%; females-21%; a ratio of 4: 1. The high proportion of males to females killed in traffic accidents may be due to the fact that (a) more males commute daily in private and commercial vehicles;. (b) more females commute daily in ...

  9. Deepwater Horizon Accident Investigation Report

    International Nuclear Information System (INIS)

    2010-09-01

    On the evening of April 20, 2010, a well control event allowed hydrocarbons to escape from the Macondo well onto Transocean's Deepwater Horizon, resulting in explosions and fire on the rig. Eleven people lost their lives, and 17 others were injured. The fire, which was fed by hydrocarbons from the well, continued for 36 hours until the rig sank. Hydrocarbons continued to flow from the reservoir through the wellbore and the blowout preventer (BOP) for 87 days, causing a spill of national significance. BP Exploration and Production Inc. was the lease operator of Mississippi Canyon Block 252, which contains the Macondo well. BP formed an investigation team that was charged with gathering the facts surrounding the accident, analyzing available information to identify possible causes and making recommendations to enable prevention of similar accidents in the future. The BP investigation team began its work immediately in the aftermath of the accident, working independently from other BP spill response activities and organizations. The ability to gather information was limited by a scarcity of physical evidence and restricted access to potentially relevant witnesses. The team had access to partial real-time data from the rig, documents from various aspects of the Macondo well's development and construction, witness interviews and testimony from public hearings. The team used the information that was made available by other companies, including Transocean, Halliburton and Cameron. Over the course of the investigation, the team involved over 50 internal and external specialists from a variety of fields: safety, operations, subsea, drilling, well control, cementing, well flow dynamic modeling, BOP systems and process hazard analysis. This report presents an analysis of the events leading up to the accident, eight key findings related to the causal chain of events and recommendations to enable the prevention of a similar accident. The investigation team worked separately

  10. Deepwater Horizon Accident Investigation Report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2010-09-15

    On the evening of April 20, 2010, a well control event allowed hydrocarbons to escape from the Macondo well onto Transocean's Deepwater Horizon, resulting in explosions and fire on the rig. Eleven people lost their lives, and 17 others were injured. The fire, which was fed by hydrocarbons from the well, continued for 36 hours until the rig sank. Hydrocarbons continued to flow from the reservoir through the wellbore and the blowout preventer (BOP) for 87 days, causing a spill of national significance. BP Exploration and Production Inc. was the lease operator of Mississippi Canyon Block 252, which contains the Macondo well. BP formed an investigation team that was charged with gathering the facts surrounding the accident, analyzing available information to identify possible causes and making recommendations to enable prevention of similar accidents in the future. The BP investigation team began its work immediately in the aftermath of the accident, working independently from other BP spill response activities and organizations. The ability to gather information was limited by a scarcity of physical evidence and restricted access to potentially relevant witnesses. The team had access to partial real-time data from the rig, documents from various aspects of the Macondo well's development and construction, witness interviews and testimony from public hearings. The team used the information that was made available by other companies, including Transocean, Halliburton and Cameron. Over the course of the investigation, the team involved over 50 internal and external specialists from a variety of fields: safety, operations, subsea, drilling, well control, cementing, well flow dynamic modeling, BOP systems and process hazard analysis. This report presents an analysis of the events leading up to the accident, eight key findings related to the causal chain of events and recommendations to enable the prevention of a similar accident. The investigation team worked

  11. Use of PSA and severe accident assessment results for the accident management

    International Nuclear Information System (INIS)

    Jang, S. H.; Kim, H. G.; Jang, H. S.; Moon, S. K.; Park, J. U.

    1993-12-01

    The objectives for this study are to investigate the basic principle or methodology which is applicable to accident management, by using the results of PSA and severe accident research, and also facilitate the preparation of accidents management program in the future. This study was performed as follows: derivation of measures for core damage prevention, derivation of measures for accident mitigation, application of computerized tool to assess severe accident management

  12. Use of PSA and severe accident assessment results for the accident management

    Energy Technology Data Exchange (ETDEWEB)

    Jang, S H; Kim, H G; Jang, H S; Moon, S K; Park, J U [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

    1993-12-15

    The objectives for this study are to investigate the basic principle or methodology which is applicable to accident management, by using the results of PSA and severe accident research, and also facilitate the preparation of accidents management program in the future. This study was performed as follows: derivation of measures for core damage prevention, derivation of measures for accident mitigation, application of computerized tool to assess severe accident management.

  13. The radiological accident in Yanango

    International Nuclear Information System (INIS)

    2000-01-01

    The use of nuclear technologies has fostered new, more effective and efficient medical procedures and has substantially improved diagnostic and therapeutic capabilities. However, in order that the benefits of the use of ionizing radiation outweigh the potential hazards posed by this medium, it is important that radiation protection and safety standards be established to govern every aspect of the application of ionizing radiation. Adherence to these standards needs to be maintained through effective regulatory control, safe operational procedures and a safety culture that is shared by all. Occasionally, established safety procedures are violated and serious radiological consequences ensue. The radiological accident described in this report, which took place in Lilo, Georgia, was a result of such an infraction. Sealed radiation sources had been abandoned by a previous owner at a site without following established regulatory safety procedures, for example by transferring the sources to the new owner or treating them as spent material and conditioning them as waste. As a consequence, 11 individuals at the site were exposed for a long period of time to high doses of radiation which resulted inter alia in severe radiation induced skin injuries. Although at the time of the accident Georgia was not an IAEA Member State and was not a signatory of the Convention on Assistance in the Case of a Nuclear Accident or Radiological Emergency, the IAEA still provided assistance to the Government of Georgia in assessing the radiological situation, while the World Health Organization (WHO) assisted in alleviating the medical consequences of the accident. The two organizations co-operated closely from the beginning, following the request for assistance by the Georgian Government. The IAEA conducted the radiological assessment and was responsible for preparing the report. The WHO and its collaborating centres within the Radiation Emergency Medical Preparedness and Assistance Network

  14. A critical assessment of energy accident studies

    International Nuclear Information System (INIS)

    Felder, Frank A.

    2009-01-01

    A comparison of two studies conducted ten years apart on energy accidents provides important insights into methodological issues and policy implications. Recommendations for further improvements in energy accident studies are developed including accounting for differences between average and incremental accident damages, testing for appropriate levels of aggregation of accidents, making references and databases publicly available, more precisely defining and reporting different types of economic damages, accounting for involuntary and voluntary risks, reporting normalized damages, raising broader public policy and planning implications and updating existing accident databases.

  15. Character and consequence of nuclear criticality accident

    International Nuclear Information System (INIS)

    Liu Xinhua; Liu Hua; Wu Deqiang; Li Bing

    2001-01-01

    The author describes some concepts, the process and magnitude of energy release and the destruction of the nuclear criticality accident and also describes the radiation consequence of criticality accidents from three aspects: prompt radiation, contamination in working place and release of fission products to the environment. It shows that the effects of radioactivity release from criticality accidents in the nuclear fuel processing plants on the environment and the public is minor, the main danger is from the external exposure of prompt rays. The paper make as have a correct understanding of the nuclear criticality accident and it would be helpful to take appropriate emergency response to potential criticality accident

  16. Regulatory approach to accident management in Sweden

    International Nuclear Information System (INIS)

    Hoegberg, L.

    1989-01-01

    The Swedish accident management program includes the following components: definition of overall safety and radiation protection objectives for the program; definition of appropriate accident management strategies to reach these objectives, based on plant-specific severe accident analysis; development and installation of appropriate accident management systems and associated management procedure; definition of roles and resposibilities for plant staff involved in accident management and implementation of appropriate training programs. The discussion of these components tries to highlight the basic technical concepts and approaches and the underlying safety philosophy rather than going into design details. 5 figs., 7 refs

  17. A critical assessment of energy accident studies

    Energy Technology Data Exchange (ETDEWEB)

    Felder, Frank A. [Edward J. Bloustein School of Planning and Public Policy, Rutgers, The State University of New Jersey, 33 Livingston Avenue, New Brunswick, NJ 08901 (United States)

    2009-12-15

    A comparison of two studies conducted ten years apart on energy accidents provides important insights into methodological issues and policy implications. Recommendations for further improvements in energy accident studies are developed including accounting for differences between average and incremental accident damages, testing for appropriate levels of aggregation of accidents, making references and databases publicly available, more precisely defining and reporting different types of economic damages, accounting for involuntary and voluntary risks, reporting normalized damages, raising broader public policy and planning implications and updating existing accident databases. (author)

  18. Severe accidents: in nuclear power plants

    International Nuclear Information System (INIS)

    1986-01-01

    A ''severe'' nuclear accident refers to a reactor accident that could exceed reactor design specifications to such a degree as to prevent cooling of the reactor's core by normal means. This report summarizes the work of a NEA Senior Group of Experts who have studied the potential response of existing light-water reactors to severe accidents and have found that current designs of reactors are far more capable of coping with severe accidents than design specifications would suggest. The report emphasises the specific knowledge and means that can be used for diagnosing a severe accident and for managing its progression in order to prevent or mitigate its consequences

  19. Cost per severe accident as an index for severe accident consequence assessment and its applications

    International Nuclear Information System (INIS)

    Silva, Kampanart; Ishiwatari, Yuki; Takahara, Shogo

    2014-01-01

    The Fukushima Accident emphasizes the need to integrate the assessments of health effects, economic impacts, social impacts and environmental impacts, in order to perform a comprehensive consequence assessment of severe accidents in nuclear power plants. “Cost per severe accident” is introduced as an index for that purpose. The calculation methodology, including the consequence analysis using level 3 probabilistic risk assessment code OSCAAR and the calculation method of the cost per severe accident, is proposed. This methodology was applied to a virtual 1,100 MWe boiling water reactor. The breakdown of the cost per severe accident was provided. The radiation effect cost, the relocation cost and the decontamination cost were the three largest components. Sensitivity analyses were carried out, and parameters sensitive to cost per severe accident were specified. The cost per severe accident was compared with the amount of source terms, to demonstrate the performance of the cost per severe accident as an index to evaluate severe accident consequences. The ways to use the cost per severe accident for optimization of radiation protection countermeasures and for estimation of the effects of accident management strategies are discussed as its applications. - Highlights: • Cost per severe accident is used for severe accident consequence assessment. • Assessments of health, economic, social and environmental impacts are included. • Radiation effect, relocation and decontamination costs are important cost components. • Cost per severe accident can be used to optimize radiation protection measures. • Effects of accident management can be estimated using the cost per severe accident

  20. SAMEX: A severe accident management support expert

    International Nuclear Information System (INIS)

    Park, Soo-Yong; Ahn, Kwang-Il

    2010-01-01

    A decision support system for use in a severe accident management following an incident at a nuclear power plant is being developed which is aided by a severe accident risk database module and a severe accident management simulation module. The severe accident management support expert (SAMEX) system can provide the various types of diagnostic and predictive assistance based on the real-time plant specific safety parameters. It consists of four major modules as sub-systems: (a) severe accident risk data base module (SARDB), (b) risk-informed severe accident risk data base management module (RI-SARD), (c) severe accident management simulation module (SAMS), and (d) on-line severe accident management guidance module (on-line SAMG). The modules are integrated into a code package that executes within a WINDOWS XP operating environment, using extensive user friendly graphics control. In Korea, the integrated approach of the decision support system is being carried out under the nuclear R and D program planned by the Korean Ministry of Education, Science and Technology (MEST). An objective of the project is to develop the support system which can show a theoretical possibility. If the system is feasible, the project team will recommend the radiation protection technical support center of a national regulatory body to implement a plant specific system, which is applicable to a real accident, for the purpose of immediate and various diagnosis based on the given plant status information and of prediction of an expected accident progression under a severe accident situation.

  1. Report on a radiotherapy underdose accident

    Energy Technology Data Exchange (ETDEWEB)

    Christodoulides, G; Christofides, S [Medical Physics Department, Nicosia General Hospital, 1450 Nicosia (Cyprus)

    1999-12-31

    Reporting information on accidents and incidents involving radiation sources provides a body of knowledge which can help to prevent accidents of a similar nature. Accident information has to be made available to users, manufacturers and regulators; An international effort to pool and analyse incident and accident information will provide more complete and reliable indicators of root causes and trends and recommendations for future accident avoidance. An accident due to human error involving a superficial x-ray therapy machine and patients treated for postoperative breast cancer is reported here. 43 women receiving radiotherapy treatment have received significantly less radiation dose than the prescribed dose. The worst dose percentage within the radiation field was 20% of the prescribed dose. The worst dose percentage on the operation scar of the breast was 52% of the prescribed radiation dose. The response to accidents/incidents in radiotherapy is discussed. (authors) 4 refs., 5 figs., 1 tabs.

  2. The epidemiology of bicyclist's collision accidents

    DEFF Research Database (Denmark)

    Larsen, L. B.

    1994-01-01

    of bicyclists and risk situations. The findings should make a basis for preventive programmes in order to decrease the number and severity of bicyclists collision accidents. Data from the emergency room in a 2 year period was combined with data from questionnaires. The study group consisted of 1021 bicyclists......The number of bicyclists injured in the road traffic in collision accidents and treated at the emergency room at Odense University Hospital has increased 66% from 1980 to 1989. The aim of this study was to examine the epidemiology of bicyclist's collision accidents and identify risk groups...... injured in collision accidents, and 1502 bicyclists injured in single accidents was used as a reference group. The young bicyclists 10-19 years of age had the highest incidence of injuries caused by collision accidents. The collision accidents had different characteristics according to counterpart. One...

  3. [Occupational noise exposure and work accidents].

    Science.gov (United States)

    Dias, Adriano; Cordeiro, Ricardo; Gonçalves, Cláudia Giglio de Oliveira

    2006-10-01

    The purpose of this study was to verify whether occupational noise exposure is a significant risk factor for work accidents in the city of Piracicaba, São Paulo State, Brazil. This hospital-based case-control study included 600 workers aged 15-60 who suffered typical occupational accidents between May and October 2004 and were seen at the Piracicaba Orthopedics and Trauma Center. The control group comprised 822 workers, aged 15-60, who were also seen at the Center, and either had a non-occupational accident or were accompanying someone who had suffered an accident. A multiple logistic regression model was adjusted with work accident as an independent variable, controlled by covariables of interest such as noise exposure. The risk of having a work accident was about twice as high among workers exposed to noise, after controlling for several covariables. Occupational noise exposure not only affected auditory health status but was also a risk factor for work accidents.

  4. DFT/PCM, QTAIM, 1H NMR conformational studies and QSAR modeling of thirty-two anti-Leishmania amazonensis Morita-Baylis-Hillman Adducts

    Science.gov (United States)

    Filho, Edilson B. A.; Moraes, Ingrid A.; Weber, Karen C.; Rocha, Gerd B.; Vasconcellos, Mário L. A. A.

    2012-08-01

    Morita-Baylis-Hillman Adducts (MBHA) has been recently synthesized and bio-evaluated by our research group against Leishmania amazonensis, parasite that causes cutaneous and mucocutaneous leishmaniasis. We present here a theoretical conformational study of thirty-two leismanicidal MBHA by B3LYP/6-31+g(d) calculations with Polarized Continuum Model (PCM) to simulate water influence. Intramolecular Hydrogen Bonds (IHBs) indicated to control the most conformational preferences of MBHA. Quantum Theory Atoms in Molecules (QTAIM) calculations were able to characterize these interactions at Bond Critical Point level. Compounds presenting an unusual seven member IHB between NO2 group and hydroxyl moiety, supported by experimental spectroscopic data, showed a considerable improvement of biological activity (lower IC50 values). These results are in accordance to redox NO2 mechanism of action. Based on structural observations, some molecular descriptors were calculated and submitted to Quantitative Structure-Activity Relationship (QSAR) studies through the PLS Regression Method. These studies provided a model with good validation parameters values (R2 = 0.71, Q2 = 0.61 and Qext2 = 0.92).

  5. Heat transfer characteristics of thermal energy storage for PCM (phase change material) melting in horizontal tube: Numerical and experimental investigations

    International Nuclear Information System (INIS)

    Aadmi, Moussa; Karkri, Mustapha; El Hammouti, Mimoun

    2015-01-01

    This paper focuses on the experimental and numerical study of the storage and release of thermal heat during melting and solidification of PCM (phase change material). Heat transfer enhancement techniques such as the use of conductors like graphite and metal tubes have been proven to be effective. The material used for thermal energy storage systems is a composite based on epoxy resin loaded with metal hollow tubes filled with paraffin wax. Differential Scanning Calorimetry has been used for measurement of melting enthalpy and determination of heat capacity. The thermophysical properties of the prepared composite phase change material have been characterized using a new transient hot plate apparatus. The results have shown that most important thermal properties of these composites at the solid and liquid states are the ‘‘apparent’’ thermal conductivity, the heat storage capacity and the latent heat of fusion. These experimental results have been simulated using numerical Comsol ® Multiphysics 4.3 based models with success. The results of the experimental investigation are compared favorably with the numerical results and thus serve to validate the numerical approach. - Highlights: • Phase change materials based on cylindrical used as new energy storage system. • Thermophysical properties and the melting process of composites were investigated. • All experimental results have been simulated using Comsol ® Multiphysiques. • The ability to store and release the thermal energy were investigated. • Good improvement in the thermal conductivity of composites

  6. Resonant-convergent PCM response theory for the calculation of second harmonic generation in makaluvamines A-V: pyrroloiminoquinone marine natural products from poriferans of genus Zyzzya.

    Science.gov (United States)

    Milne, Bruce F; Norman, Patrick

    2015-05-28

    The first-order hyperpolarizability, β, has been calculated for a group of marine natural products, the makaluvamines. These compounds possess a common cationic pyrroloiminoquinone structure that is substituted to varying degrees. Calculations at the MP2 level indicate that makaluvamines possessing phenolic side chains conjugated with the pyrroloiminoquinone moiety display large β values, while breaking this conjugation leads to a dramatic decrease in the calculated hyperpolarizability. This is consistent with a charge-transfer donor-π-acceptor (D-π-A) structure type, characteristic of nonlinear optical chromophores. Dynamic hyperpolarizabilities calculated using resonance-convergent time-dependent density functional theory coupled to polarizable continuum model (PCM) solvation suggest that significant resonance enhancement effects can be expected for incident radiation with wavelengths around 800 nm. The results of the current work suggest that the pyrroloiminoquinone moiety represents a potentially useful new chromophore subunit, in particular for the development of molecular probes for biological imaging. The introduction of solvent-solute interactions in the theory is conventionally made in a density matrix formalism, and the present work will provide detailed account of the approximations that need to be introduced in wave function theory and our program implementation. The program implementation as such is achieved by a mere combination of existing modules from previous developments, and it is here only briefly reviewed.

  7. Thermophysical Parameters of Organic PCM Coconut Oil from T-History Method and Its Potential as Thermal Energy Storage in Indonesia

    Science.gov (United States)

    Silalahi, Alfriska O.; Sukmawati, Nissa; Sutjahja, I. M.; Kurnia, D.; Wonorahardjo, S.

    2017-07-01

    The thermophysical parameters of organic phase change material (PCM) of coconut oil (co_oil) have been studied by analyzing the temperature vs time data during liquid-solid phase transition (solidification process) based on T-history method, adopting the original version and its modified form to extract the values of mean specific heats of the solid and liquid co_oil and the heat of fusion related to phase transition of co_oil. We found that the liquid-solid phase transition occurs rather gradually, which might be due to the fact that co_oil consists of many kinds of fatty acids with the largest amount of lauric acid (about 50%), with relatively small supercooling degree. For this reason, the end of phase transition region become smeared out, although the inflection point in the temperature derivative is clearly observed signifying the drastic temperature variation between the phase transition and solid phase periods. The data have led to the values of mean specific heat of the solid and liquid co_oil that are comparable to the pure lauric acid, while the value for heat of fusion is resemble to those of the DSC result, both from references data. The advantage of co_oil as the potential sensible and latent TES for room-temperature conditioning application in Indonesia is discussed in terms of its rather broad working temperature range due to its mixture composition characteristic.

  8. Psychological factors of radiation accidents

    International Nuclear Information System (INIS)

    Lartsev, M.A.

    1995-01-01

    With reference to world, internal and personal experience, an attempt is made to reveal psychological mechanisms determining the attitude of a person to ionizing radiation using for this purpose the conceptions of mental stress and psychological adaptation. On the example of Chernobyl Nuclear Power Plant, in the light of the above conceptions, the paper describes psychic reactions of the personnel of the nuclear power plant and other groups of people to the heavy radiation accident. For improvement of the activity for liquidation of the accident after-effects it is suggested to use the system of psychophysiological support of the rescue units, including psychophysiological training and support, as well as functional rehabilitation of specialists. 11 refs

  9. Fatal motorcycle accidents and alcohol

    DEFF Research Database (Denmark)

    Larsen, C F; Hardt-Madsen, M

    1987-01-01

    A series of fatal motorcycle accidents from a 7-year period (1977-1983) has been analyzed. Of the fatalities 30 were operators of the motorcycle, 11 pillion passengers and 8 counterparts. Of 41 operators 37% were sober at the time of accident, 66% had measurable blood alcohol concentration (BAC......); 59% above 0.08%. In all cases where a pillion passenger was killed, the operator of the motorcycle had a BAC greater than 0.08%. Of the killed counterparts 2 were non-intoxicated, 2 had a BAC greater than 0.08%, and 4 were not tested. The results advocate that the law should restrict alcohol...... consumption by pillion passengers as well as by the motorcycle operator. Suggestions made to extend the data base needed for developing appropriate alcohol countermeasures by collecting sociodemographic data on drivers killed or seriously injured should be supported....

  10. The detection of criticality accidents

    International Nuclear Information System (INIS)

    Prigent, R.; Renard, C.

    It is necessary to shield the personnel from the radiological consequences of a criticality accident. In the past ten years the study programmes have highlighted fresh data which have led to new thinking on the detection philosophy and as a consequence the design of detection equipment. Concurrently, new recommendations have been drawn up by the Safety Criticality Committee. The new detection equipment was developed by the CEA on the basis of the CRAC and SILENE experiments. Its industrialization was entrusted to the Intertechnique Company and the first network installed dates back to 1976. An examination is made of the problem of accident detection, dealing in turn with detection, the characteristics of the equipment and the installation rules. To clarify the various points discussed, a parallel has been drawn between the equipment existing up to 1975 and the new generation developed since then [fr

  11. Regulatory aspects of nuclear accidents

    International Nuclear Information System (INIS)

    Caoui, A.

    1988-01-01

    The legislative systems used in different countries insist on requiring the license of the nuclear installations exploitation and on providing a nuclear safety report. For obtaining this license, the operators have to consider all situations of functioning (normal, incidental and accidental) to make workers and the public secure. The licensing procedures depend on the juridical and administrative systems of the country. Usually, protection of people against ionzing radiation is the responsibility of the ministry of health and the ministry of industry. In general, the regulations avoid to fix a definite technical standards by reason of technological development. An emergency plan is normally designed in the stage of the installation project planification. This plan contains the instructions and advices to give to populations in case of accident. The main lesson learnt from the nuclear accidents that happened is to enlarge the international cooperation in the nuclear safety field. 4 refs. (author)

  12. Recommendations about criticality accident dosimetry

    International Nuclear Information System (INIS)

    1975-07-01

    The aims of criticality accident dosimetry and the characteristics peculiar to a critical burst being defined, the requirements to be fulfilled by a dosimetric system applied to this type of measurements are presented. The devices chosen by the C.E.A. Radiation Survey Divisions, simple and cheap, are described along with the main processes to be carried out in order to evaluate doses after an accident. The apparatus necessary for detector counting and the directions for use are presented in detail, allowing standardization of measurements. A set of linear formula enables to obtain, from these measurements, all required informations about neutron fluences and spectra, along with the suitable components of the dose at the irradiated people locations [fr

  13. Transport accident emergency response plan

    International Nuclear Information System (INIS)

    Vallette-Fontaine, M.; Frantz, P.

    1998-01-01

    To comply with the IAEA recommendations for the implementation of an Emergency Response Plan as described in Safety Series 87, Transnucleaire, a company deeply involved in the road and rail transports of the fuel cycle, masters means of Emergency Response in the event of a transport accident. This paper aims at analyzing the solutions adopted for the implementation of an Emergency Response Plan and the development of a technical support and adapted means for the recovery of heavy packagings. (authors)

  14. Radiation accident in Viet Nam

    International Nuclear Information System (INIS)

    Wheatley, J.

    1998-01-01

    In November 1992 a Vietnamese research physicist was working with a microtron accelerator when he received a radiation overexposure that required the subsequent amputation of his right hand. A team from the International Atomic Energy Agency visited Hanoi in March 1993 to carry out an investigation. It was concluded that the accident occurred primarily due to a lack of safety systems although the lack of both written procedures and training in basic radiation safety were also major contributors. (author)

  15. Modelling Accident Tolerant Fuel Concepts

    Energy Technology Data Exchange (ETDEWEB)

    Hales, Jason Dean [Idaho National Laboratory; Gamble, Kyle Allan Lawrence [Idaho National Laboratory

    2016-05-01

    The catastrophic events that occurred at the Fukushima-Daiichi nuclear power plant in 2011 have led to widespread interest in research of alternative fuels and claddings that are proposed to be accident tolerant. The United States Department of Energy (DOE) through its Nuclear Energy Advanced Modeling and Simulation (NEAMS) program has funded an Accident Tolerant Fuel (ATF) High Impact Problem (HIP). The ATF HIP is a three-year project to perform research on two accident tolerant concepts. The final outcome of the ATF HIP will be an in-depth report to the DOE Advanced Fuels Campaign (AFC) giving a recommendation on whether either of the two concepts should be included in their lead test assembly scheduled for placement into a commercial reactor in 2022. The two ATF concepts under investigation in the HIP are uranium silicide fuel and iron-chromium-aluminum (FeCrAl) alloy cladding. Utilizing the expertise of three national laboratory participants (Idaho National Laboratory, Los Alamos National Laboratory, and Argonne National Laboratory), a comprehensive multiscale approach to modeling is being used that includes atomistic modeling, molecular dynamics, rate theory, phase-field, and fuel performance simulations. Model development and fuel performance analysis are critical since a full suite of experimental studies will not be complete before AFC must prioritize concepts for focused development. In this paper, we present simulations of the two proposed accident tolerance fuel systems: U3Si2 fuel with Zircaloy-4 cladding, and UO2 fuel with FeCrAl cladding. Sensitivity analyses are completed using Sandia National Laboratories’ Dakota software to determine which input parameters (e.g., fuel specific heat) have the greatest influence on the output metrics of interest (e.g., fuel centerline temperature). We also outline the multiscale modelling approach being employed. Considerable additional work is required prior to preparing the recommendation report for the Advanced

  16. The radiation accident at Juarez

    International Nuclear Information System (INIS)

    Koenig, L.A.

    1985-01-01

    During unconscious disassembly of a Co-60 therapy unit, 6010 metal pellets of 1 mm diameter each having 2.6 GBq (70 mCi) of activity were distributed in an uncontrolled manner. The incident was detected by mere chance. The event and the consequences are illustrated. The resulting collective dose is estimated to be 100 times bigger than that caused by the Harrisburg accident. (orig.) [de

  17. The reactor accident of Chernobyl

    International Nuclear Information System (INIS)

    Koenig, L.A.; Schuettelkopf, H.; Erat, S.; Fessler, H.; Hempelmann, S.; Maurer, K.; Pimpl, M.; Radziwill, A.

    1986-08-01

    The contamination, caused by the radioactivity released during the reactor accident of Chernobyl was measured in samples taken in the environment of the Karlsruhe Nuclear Research Center. The radioactivity was determined in air, fodder, milk, vegetables, other plants, foodstuffs, soil, precipitations, drinking water, sludge and other samples. Results of measurements are reported which were received with considerably more than 1000 samples. The evaluation of the data will be presented in KfK 4140. (orig.) [de

  18. Chernobyl accident: Assessing the data

    Energy Technology Data Exchange (ETDEWEB)

    Soerensen, B

    1986-01-01

    Data presented in the official Soviet report to the IAEA on the Chernobyl reactor accident are critically assessed. Special attention is given to the derivation of release fractions from fallout measurements, a procedure which is demonstrated to involve large elements of uncertainty. Further comments relate to estimates of plume rise and deposition velocity. A comparison is made with the predictions of previously published theoretical reactor safety studies.

  19. Medical management of radiation accidents

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-12-31

    The film gives advice on actions to be taken in case of a radiation accident. It addresses involving external irradiation of the whole and partial body, very localized exposure, uptake of radioiodine, inhalation of transuranium elements and a wound of a finger. The film is intended to illustrate the Agency`s Safety Series No. 47 entitled ``Manual on Early Medical Treatment of Possible Radiation Injury`` published in 1978

  20. Accident Locations, MDTA Accidents, Accidents on MDTA locations, Accidents on I 95, US 50, I 695, Accident on John F Kennedy Highway, Nice Bridge, Bay Bridge locations, Published in 2011, 1:1200 (1in=100ft) scale, Maryland Transportation Authority.

    Data.gov (United States)

    NSGIC State | GIS Inventory — Accident Locations dataset current as of 2011. MDTA Accidents, Accidents on MDTA locations, Accidents on I 95, US 50, I 695, Accident on John F Kennedy Highway, Nice...

  1. Accident analysis and DOE criteria

    International Nuclear Information System (INIS)

    Graf, J.M.; Elder, J.C.

    1982-01-01

    In analyzing the radiological consequences of major accidents at DOE facilities one finds that many facilities fall so far below the limits of DOE Order 6430 that compliance is easily demonstrated by simple analysis. For those cases where the amount of radioactive material and the dispersive energy available are enough for accident consequences to approach the limits, the models and assumptions used become critical. In some cases the models themselves are the difference between meeting the criteria or not meeting them. Further, in one case, we found that not only did the selection of models determine compliance but the selection of applicable criteria from different chapters of Order 6430 also made the difference. DOE has recognized the problem of different criteria in different chapters applying to one facility, and has proceeded to make changes for the sake of consistency. We have proposed to outline the specific steps needed in an accident analysis and suggest appropriate models, parameters, and assumptions. As a result we feed DOE siting and design criteria will be more fairly and consistently applied

  2. [Multicenter paragliding accident study 1990].

    Science.gov (United States)

    Lautenschlager, S; Karli, U; Matter, P

    1992-01-01

    During the period from 1.1.90 until 31.12.90, 86 injuries associated with paragliding were analyzed in a prospective study in 12 different Swiss hospitals with reference to causes, patterns, and frequencies. The injuries showed a mean score of over 2 and were classified as severe. Most frequent spine injuries (36%) and lesions of the lower extremity (35%) with a high risk of the ankles were diagnosed. One accident was fatal. 60% of the accidents happened during landing, 26% during launching and 14% during flight. Half of the pilots were affected during their primary training course. Most accidents were caused by inflight error of judgement--especially incorrect estimation of wind conditions--and further the choice of unfavourable landing sites. In contrast to previous injury-reports, only one equipment failure could be noted, but often the equipment was not corresponding with the experience and the weight of the pilot. To reduce the frequency of paragliding-injuries an accurate choice of equipment and an increased attention to environmental factors is mandatory. Furthermore an education-program regarding the attitude and intelligence of the pilot should be included in training courses.

  3. Medical consequences of Chernobyl accident

    Directory of Open Access Journals (Sweden)

    Galstyan I.A.

    2015-12-01

    Full Text Available Aim: to study the long-term effects of acute radiation syndrome (ARS, developed at the victims of the Chernobyl accident. Material and Methods. 237 people were exposed during the accident, 134 of them were diagnosed with ARS. Dynamic observation implies a thorough annual examination in a hospital. Results. In the first 1.5-2 years after the ARS mean group indices of peripheral blood have returned to normal. However, many patients had transient expressed moderate cytopenias. Granulocytopenia, thrombocytopenia, lymphopenia and erythropenia were the most frequently observed things during the first 5 years after the accident. After 5 years their occurences lowered. In 11 patients the radiation cataract was detected. A threshold dose for its development is a dose of 3.2 Gy Long-term effects of local radiation lesions (LRL range from mild skin figure smoothing to a distinct fibrous scarring, contractures, persistently recurrent late radiation ulcers. During all years of observation we found 8 solid tumors, including 2 thyroid cancers. 5 hematologic diseases were found. During 29 years 26 ARS survivors died of various causes. Conclusion. The health of ones with long-term ARS effects is determined by the evolution of the LRL effects on skin, radiation cataracts, hema-tological diseases and the accession of of various somatic diseases, not caused by radiation.

  4. The management of severe accidents

    International Nuclear Information System (INIS)

    Pelce, J.; Brignon, P.

    1987-01-01

    In considering severe accidents in water power reactors, a major problem that arises is how to manage them in such a way that the situation can be controlled as well as possible, from the aspects both of preventing serious damage to the core of limiting the discharge of radioactivity. A number of countries have announced provisions in the field of accident management, some already set up, others planned, but these mainly apply to preventing damage to the core. Part of this report deals with this aspect, to show that there is a fairly wide consensus on how problems should be approached. Attitudes vary, on the other hand, in the approach to mitigate radioactive release. In fact, few countries have proposed concrete steps to manage severe accidents in the final stages when the core is seriously damaged. Since it is difficult to compare different approaches, only the French approach is described. This description is however very brief, because in the five or six years since it was defined, the approach has been presented many times. The stress is placed more on the comments which this type of approach suggests, to make the subsequent general discussion easier

  5. The consequences of Chernobyl accident

    Directory of Open Access Journals (Sweden)

    Ion Chioșilă

    2016-12-01

    Full Text Available These days marks 30 years since the Chernobyl nuclear accident, followed by massive radioactive contamination of the environment and human in Belarus, Ukraine and Russia, and resulted in many deaths among people who intervened to decrease the effects of the nuclear disaster. The 26 April 1986 nuclear accident contaminated all European countries, but at a much lower level, without highlighted consequences on human health. In special laboratories, the main radionuclides (I-131, Cs-137, Cs-134 and Sr-90 were also analyzed in Romania from environmental samples, food, even human subjects. These radionuclides caused the population to receive a low dose of about 1 mSv in 1986 that is half of the dose of the natural background radiation (2.4 mSv per year. As in all European countries (excluding Ukraine, Belarus and Russia this dose of about 1 mSv fell rapidly by 1990, reaching levels close to ones before the accident at the nuclear tests.

  6. Chernobyl accident. Exposures and effects

    International Nuclear Information System (INIS)

    Bennett, B.; Bouville, A.; Hall, P.; Savkin, M.; Storm, H.

    2000-01-01

    The Chernobyl accident that occurred in Ukraine in April 1986 happened during an experimental test of the electrical control system as the reactor was being shut down for routine maintenance. The operators, in violation of safety regulations, had switched off important control systems and allowed the reactor to reach unstable, low-power conditions. A sudden power surge caused a steam explosion that ruptured the reactor vessel and allowed further violent fuel-steam interactions that destroyed the reactor and the reactor building. The Chernobyl accident was the most serious to have ever occurred in the nuclear power industry. The accident caused the early death of 30 power plant employees and fire fighters and resulted in widespread radioactive contamination in areas of Belarus, the Russian Federation, and Ukraine inhabited by several million people. Radionuclides released from the reactor that caused exposure of individuals were mainly iodine-131, caesium-134 and caesium-137. Iodine-131 has a short radioactive half-life (8 days), but it can be transferred relatively rapidly through milk and leafy vegetables to humans. Iodine becomes localized in the thyroid gland. For reasons of intake of these foods, size of thyroid gland and metabolism, the thyroid doses are usually greater to infants and children than to adults. The isotopes of caesium have relatively long half-lives (caesium-134: 2 years; caesium-137: 30 years). These radionuclides cause long-term exposures through the ingestion pathway and from external exposure to these radionuclides deposited on the ground. In addition to radiation exposure, the accident caused long-term changes in the lives of people living in the contaminated regions, since measures intended to limit radiation doses included resettlements, changes in food supplies, and restrictions in activities of individuals and families. These changes were accompanied by major economic, social and political changes in the affected countries resulting

  7. Thyroid blocking after nuclear accidents

    International Nuclear Information System (INIS)

    Rendl, J.; Reiners, C.

    1999-01-01

    Following the Chernobyl accident a marked increase in thyroid cancer incidence among the children in Belarus, the Ukraine and Russia has been detected, strongly suggesting a causal relationship to the large amounts of radioactive iodine isotopes in the resulting fallout. Taking into account the Chernobyl experience the German Committee on Radiation Protection decided to reduce the intervention levels on the basis of the 1989 WHO recommendations and adopted a new concept concerning thyroid blocking in response to nuclear power plant accidents. Experimental animal studies and theoretical considerations show that thyroid blocking with potassium iodide (KI) in a dose of about 1.4 mg per kg body weight is most effective in reducing irradiation to the thyroid from the intake of radioiodine nuclides, provided KI is given within 2 hours after exposure. According to the new concept, persons over 45 years of age should not take iodine tablets because the drug could cause a greater health risk due to prevalent functional thyroid autonomy in this age group than the radioactive iodine averted by KI. On the basis of accident analysis and the new philosophy suitable distribution strategies and logistics are proposed and discussed. (orig.) [de

  8. Severe accidents at nuclear power plants. Their risk assessment and accident management

    International Nuclear Information System (INIS)

    Abe, Kiyoharu.

    1995-05-01

    This document is to explain the severe accident issues. Severe Accidents are defined as accidents which are far beyond the design basis and result in severe damage of the core. Accidents at Three Mild Island in USA and at Chernobyl in former Soviet Union are examples of severe accidents. The causes and progressions of the accidents as well as the actions taken are described. Probabilistic Safety Assessment (PSA) is a method to estimate the risk of severe accidents at nuclear reactors. The methodology for PSA is briefly described and current status on its application to safety related issues is introduced. The acceptability of the risks which inherently accompany every technology is then discussed. Finally, provision of accident management in Japan is introduced, including the description of accident management measures proposed for BWRs and PWRs. (author)

  9. Criticality accident of nuclear fuel facility. Think back on JCO criticality accident

    International Nuclear Information System (INIS)

    Naito, Keiji

    2003-09-01

    This book is written in order to understand the fundamental knowledge of criticality safety or criticality accident of nuclear fuel facility by the citizens. It consists of four chapters such as critical conditions and criticality accident of nuclear facility, risk of criticality accident, prevention of criticality accident and a measure at an occurrence of criticality accident. A definition of criticality, control of critical conditions, an aspect of accident, a rate of incident, damage, three sufferers, safety control method of criticality, engineering and administrative control, safety design of criticality, investigation of failure of safety control of JCO criticality accident, safety culture are explained. JCO criticality accident was caused with intention of disregarding regulation. It is important that we recognize the correct risk of criticality accident of nuclear fuel facility and prevent disasters. On the basis of them, we should establish safety culture. (S.Y.)

  10. Evaluation of severe accident environmental conditions taking accident management strategy into account for equipment survivability assessments

    International Nuclear Information System (INIS)

    Lee, Byung Chul; Jeong, Ji Hwan; Na, Man Gyun; Kim, Soong Pyung

    2003-01-01

    This paper presents a methodology utilizing accident management strategy in order to determine accident environmental conditions in equipment survivability assessments. In case that there is well-established accident management strategy for specific nuclear power plant, an application of this tool can provide a technical rationale on equipment survivability assessment so that plant-specific and time-dependent accident environmental conditions could be practically and realistically defined in accordance with the equipment and instrumentation required for accident management strategy or action appropriately taken. For this work, three different tools are introduced; Probabilistic Safety Assessment (PSA) outcomes, major accident management strategy actions, and Accident Environmental Stages (AESs). In order to quantitatively investigate an applicability of accident management strategy to equipment survivability, the accident simulation for a most likely scenario in Korean Standard Nuclear Power Plants (KSNPs) is performed with MAAP4 code. The Accident Management Guidance (AMG) actions such as the Reactor Control System (RCS) depressurization, water injection into the RCS, the containment pressure and temperature control, and hydrogen concentration control in containment are applied. The effects of these AMG actions on the accident environmental conditions are investigated by comparing with those from previous normal accident simulation, especially focused on equipment survivability assessment. As a result, the AMG-involved case shows the higher accident consequences along the accident environmental stages

  11. Ambulance traffic accidents in Taiwan.

    Science.gov (United States)

    Chiu, Po-Wei; Lin, Chih-Hao; Wu, Chen-Long; Fang, Pin-Hui; Lu, Chien-Hsin; Hsu, Hsiang-Chin; Chi, Chih-Hsien

    2018-04-01

    Ambulance traffic accidents (ATAs) are the leading cause of occupation-related fatalities among emergency medical service (EMS) personnel. We aim to use the Taiwan national surveillance system to analyze the characteristics of ATAs and to assist EMS directors in developing policies governing ambulance operations. A retrospective, cross-sectional and largely descriptive study was conducted using Taiwan national traffic accidents surveillance data from January 1, 2011 to October 31, 2016. Among the 1,627,217 traffic accidents during the study period, 715 ATAs caused 8 deaths within 24 h and 1844 injured patients. On average, there was one ATA for every 8598 ambulance runs. Compared to overall traffic accidents, ATAs were 1.7 times more likely to result in death and 1.9 times more likely to have injured patients. Among the 715 ATAs, 8 (1.1%) ATAs were fatal and 707 (98.9%) were nonfatal. All 8 fatalities were associated with motorcycles. The urban areas were significantly higher than the rural areas in the annual number of ATAs (14.2 ± 7.3 [7.0-26.7] versus 3.1 ± 1.9 [0.5-8.4], p = 0.013), the number of ATA-associated fatalities per year (0.2 ± 0.2 [0.0-0.7] versus 0.1 ± 0.1 [0.0-0.2], p = 0.022), and the annual number of injured patients (who needed urgent hospital visits) in ATAs (19.4 ± 7.3 [10.5-30.9] versus 5.2 ± 3.8 [0.9-15.3], p traffic accident reporting system should be built to provide EMS policy guidance for ATA reduction and outcome improvements. Copyright © 2018. Published by Elsevier B.V.

  12. Severe Accident Recriticality Analyses (SARA)

    Energy Technology Data Exchange (ETDEWEB)

    Frid, W. [Swedish Nuclear Power Inspectorate, Stockholm (Sweden); Hoejerup, F. [Risoe National Lab. (Denmark); Lindholm, I.; Miettinen, J.; Puska, E.K. [VTT Energy, Helsinki (Finland); Nilsson, Lars [Studsvik Eco and Safety AB, Nykoeping (Sweden); Sjoevall, H. [Teoliisuuden Voima Oy (Finland)

    1999-11-01

    Recriticality in a BWR has been studied for a total loss of electric power accident scenario. In a BWR, the B{sub 4}C control rods would melt and relocate from the core before the fuel during core uncovery and heat-up. If electric power returns during this time-window unborated water from ECCS systems will start to reflood the partly control rod free core. Recriticality might take place for which the only mitigating mechanisms are the Doppler effect and void formation. In order to assess the impact of recriticality on reactor safety, including accident management measures, the following issues have been investigated in the SARA project: 1. the energy deposition in the fuel during super-prompt power burst, 2. the quasi steady-state reactor power following the initial power burst and 3. containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core state initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality - both superprompt power bursts and quasi steady-state power generation - for the studied range of parameters, i. e. with core uncovery and heat-up to maximum core temperatures around 1800 K and water flow rates of 45 kg/s to 2000 kg/s injected into the downcomer. Since the recriticality takes place in a small fraction of the core the power densities are high which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal/g, was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding

  13. Severe accident recriticality analyses (SARA)

    Energy Technology Data Exchange (ETDEWEB)

    Frid, W. E-mail: wiktor.frid@ski.se; Hoejerup, F.; Lindholm, I.; Miettinen, J.; Nilsson, L.; Puska, E.K.; Sjoevall, H

    2001-11-01

    Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies, the following issues have been investigated in the SARA project: (1) the energy deposition in the fuel during super-prompt power burst; (2) the quasi steady-state reactor power following the initial power burst; and (3) containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality--both super-prompt power bursts and quasi steady-state power generation--for the range of parameters studied, i.e. with core uncovering and heat-up to maximum core temperatures of approximately 1800 K, and water flow rates of 45-2000 kg s{sup -1} injected into the downcomer. Since recriticality takes place in a small fraction of the core, the power densities are high, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g{sup -1}, was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s{sup -1}. In most cases, however, the predicted energy deposition was smaller, below the regulatory limits for fuel failure, but close to or above recently observed thresholds for fragmentation and dispersion of high burn-up fuel. The highest calculated

  14. Severe accident recriticality analyses (SARA)

    International Nuclear Information System (INIS)

    Frid, W.; Hoejerup, F.; Lindholm, I.; Miettinen, J.; Nilsson, L.; Puska, E.K.; Sjoevall, H.

    2001-01-01

    Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies, the following issues have been investigated in the SARA project: (1) the energy deposition in the fuel during super-prompt power burst; (2) the quasi steady-state reactor power following the initial power burst; and (3) containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality--both super-prompt power bursts and quasi steady-state power generation--for the range of parameters studied, i.e. with core uncovering and heat-up to maximum core temperatures of approximately 1800 K, and water flow rates of 45-2000 kg s -1 injected into the downcomer. Since recriticality takes place in a small fraction of the core, the power densities are high, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g -1 , was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s -1 . In most cases, however, the predicted energy deposition was smaller, below the regulatory limits for fuel failure, but close to or above recently observed thresholds for fragmentation and dispersion of high burn-up fuel. The highest calculated quasi steady

  15. Severe Accident Recriticality Analyses (SARA)

    International Nuclear Information System (INIS)

    Frid, W.; Hoejerup, F.; Lindholm, I.; Miettinen, J.; Puska, E.K.; Nilsson, Lars; Sjoevall, H.

    1999-11-01

    Recriticality in a BWR has been studied for a total loss of electric power accident scenario. In a BWR, the B 4 C control rods would melt and relocate from the core before the fuel during core uncovery and heat-up. If electric power returns during this time-window unborated water from ECCS systems will start to reflood the partly control rod free core. Recriticality might take place for which the only mitigating mechanisms are the Doppler effect and void formation. In order to assess the impact of recriticality on reactor safety, including accident management measures, the following issues have been investigated in the SARA project: 1. the energy deposition in the fuel during super-prompt power burst, 2. the quasi steady-state reactor power following the initial power burst and 3. containment response to elevated quasi steady-state reactor power. The approach was to use three computer codes and to further develop and adapt them for the task. The codes were SIMULATE-3K, APROS and RECRIT. Recriticality analyses were carried out for a number of selected reflooding transients for the Oskarshamn 3 plant in Sweden with SIMULATE-3K and for the Olkiluoto 1 plant in Finland with all three codes. The core state initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality - both superprompt power bursts and quasi steady-state power generation - for the studied range of parameters, i. e. with core uncovery and heat-up to maximum core temperatures around 1800 K and water flow rates of 45 kg/s to 2000 kg/s injected into the downcomer. Since the recriticality takes place in a small fraction of the core the power densities are high which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal/g, was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding

  16. Approach to accident management in RBMK-1500

    International Nuclear Information System (INIS)

    Kaliatka, A.; Urbonavicius, E.; Uspuras, E.

    2008-01-01

    In order to ensure the safe operation of the nuclear power plants accident management programs are being developed around the world. These accident management programs cover the whole spectrum of accidents, including severe accidents. A lot of work is done to investigate the severe accident phenomena and implement severe accident management in NPPs with vessel-type reactors, while less attention is paid to channel-type reactors CANDU and RBMK. Ignalina NPP with RBMK-1500 reactor has implemented symptom based emergency operation procedures, which cover management of accidents until the core damage and do not extend to core damage region. In order to ensure coverage of the whole spectrum of accidents and meet the requirements of IAEA the severe accident management guidelines have to be developed. This paper presents the basic principles and approach to management of beyond design basis accidents at Ignalina NPP. In general, this approach could be applied to NPPs with RBMK-1000 reactors that are available in Russia, but the design differences should be taken into account

  17. Response to the Chernobyl accident in Japan

    International Nuclear Information System (INIS)

    Anon.

    1986-01-01

    The worst nuclear accident in history happened at No.4 unit of the Chernobyl Atomic Power Station in USSR. Since the Chernobyl accident, a number of measures have been introduced in many countries, including the reconsideration of programs for construction and operation of nuclear power plants. In Japan, the press and television first reported the accident on April 29. The next day, all the relevant governmental agencies began to collect and analyze information in order to prepare possible countermeasures. The Nuclear Safety Commission issued a statement covering three points: 1) the radioactive substances released by the accident will have virtually no influence on the health of people in Japan, 2) a Special Committee on the Chernobyl Atomic Power Station Accident will be established, and 3) the Soviet government must provide all detailed information about the accident as soon as it is available. On April 30, the Committee on Radioactivity decided to increase radioactivity observations by the Science and Technology Agency, the Defence Agency, and the Meteorological Agency. On the same day, the Ministry of International Trade and Industry set up a survey committee for the Chernobyl accident with the responsibility of collecting and analyzing information about the accident. A review is also made in this article as to how the Japanese media reported the accident and how people reacted on reading the newspapers and watching TV on the accident. (Nogami, K.)

  18. [Accidents in travellers - the hidden epidemic].

    Science.gov (United States)

    Walz, Alexander; Hatz, Christoph

    2013-06-01

    The risk of malaria and other communicable diseases is well addressed in pre-travel advice. Accidents are usually less discussed. Thus, we aimed at assessing accident figures for the Swiss population, based on data of the register from 2004 to 2008 of the largest Swiss accident insurance organization (SUVA). More than 139'000 accidents over 5 years showed that 65 % of the accidents overseas are injuries, and 24 % are caused by poisoning or harm by cold, heat or air pressure. Most accidents happened during leisure activities or sports. More than one third of the non-lethal and more than 50 % of the fatal accidents happened in Asia. More than three-quarters of non-lethal accidents take place in people between 25 and 54 years. One out of 74 insured persons has an accident abroad per year. Despite of many analysis short-comings of the data set with regard to overseas travel, the figures document the underestimated burden of disease caused by accidents abroad and should affect the given pre-health advice.

  19. Use of bayesian operations for diagnosing accidents

    International Nuclear Information System (INIS)

    Kang, K.M.; Jae, M.; Suh, K.Y.

    2005-01-01

    In complex systems, it is necessary to model a logical representation of the overall system interaction with respect to the individual subsystems. Operators are allowed to follow EOPs (Emergency Operating Procedures) when reactor tripped because of accidents. But, it's very difficult to diagnose accidents and find out appropriate procedures to mitigate current accidents in a given short time. Even if they diagnose accidents, it also has possibility to misdiagnose. TMI accident is a good example of operators' errors. Methodology using Influence Diagrams has been developed and applied for representing the dependency behaviors and uncertain behaviors of complex systems. An example to diagnose the accidents such as SLOCA and SGTR with similar symptoms has been introduced. From the constructed model, operators could diagnose accidents at any states of accidents. This model can offer the information about accidents with given symptoms. This model might help operators to diagnose correctly and rapidly. It might be very useful to support operators to reduce human error. Also, from this study, it is applicable to diagnose other accidents with similar symptoms and to analyze causes of reactor trip. (authors)

  20. Strategy generation in accident management support

    International Nuclear Information System (INIS)

    Sirola, M.

    1995-01-01

    An increased interest for research in the field of Accident Management can be noted. Several international programmes have been started in order to be able to understand the basic physical and chemical phenomena in accident conditions. A feasibility study has shown that it would be possible to design and develop a computerized support system for plant staff in accident situations. To achieve this goal the Halden Project has initiated a research programme on Computerized Accident Management Support (CAMS project). The aim is to utilize the capabilities of computerized tools to support the plant staff during the various accident stages. The system will include identification of the accident state, assessment of the future development of the accident and planning of accident mitigation strategies. A prototype is developed to support operators and the Technical Support Centre in decision making during serious accident in nuclear power plants. A rule based system has been built to take care of the strategy generation. This system assists plant personnel in planning control proposals and mitigation strategies from normal operation to severe accident conditions. The ideal of a safety objective tree and knowledge from the emergency procedures have been used. Future prediction requires good state identification of the plant status and some knowledge about the history of some critical variables. The information needs to be validated as well. Accurate calculations in simulators and a large database including all important information form the plant will help the strategy planning. (author). 12 refs, 2 figs

  1. NPP Krsko Severe Accident Management Guidelines Implementation

    International Nuclear Information System (INIS)

    Basic, I.; Krajnc, B.; Bilic-Zabric, T.; Spiler, J.

    2002-01-01

    Severe Accident Management is a framework to identify and implement the Emergency Response Capabilities that can be used to prevent or mitigate severe accidents and their consequences. The USA NRC has indicated that the development of a licensee plant specific accident management program will be required in order to close out the severe accident regulatory issue (Ref. SECY-88-147). Generic Letter 88-20 ties the Accident management Program to IPE for each plant. The SECY-89-012 defines those actions taken during the course of an accident by the plant operating and technical staff to: 1) prevent core damage, 2) terminate the progress of core damage if it begins and retain the core within the reactor vessel, 3) maintain containment integrity as long as possible, and 4) minimize offsite releases. The subject of this paper is to document the severe accident management activities, which resulted in a plant specific Severe Accident Management Guidelines implementation. They have been developed based on the Krsko IPE (Individual Plant Examination) insights, Generic WOG SAMGs (Westinghouse Owners Group Severe Accident Management Guidances) and plant specific documents developed within this effort. Among the required plant specific actions the following are the most important ones: Identification and documentation of those Krsko plant specific severe accident management features (which also resulted from the IPE investigations). The development of the Krsko plant specific background documents (Severe Accident Plant Specific Strategies and SAMG Setpoint Calculation). Also, paper discusses effort done in the areas of NPP Krsko SAMG review (internal and external ), validation on Krsko Full Scope Simulator (Severe Accident sequences are simulated by MAAP4 in real time) and world 1st IAEA Review of Accident Management Programmes (RAMP). (author)

  2. Specific features of RBMK severe accidents progression and approach to the accident management

    International Nuclear Information System (INIS)

    Vasilevskij, V.P.; Nikitin, Yu.M.; Petrov, A.A.; Potapov, A.A.; Cherkashov, Yu.M.

    2001-01-01

    Fundamental construction features of the LWGR facilities (absence of common external containment shell, disintegrated circulation circuit and multichannel reactor core, positive vapor reactivity coefficient, high mass of thermally capacious graphite moderator) predetermining development of assumed heavy non-projected accidents and handling them are treated. Rating the categories of the reactor core damages for non-projected accidents and accident types producing specific grope of damages is given. Passing standard non-projected accidents, possible methods of attack accident consequences, as well as methods of calculated analysis of non-projected accidents are demonstrated [ru

  3. Major Accidents (Gray Swans) Likelihood Modeling Using Accident Precursors and Approximate Reasoning.

    Science.gov (United States)

    Khakzad, Nima; Khan, Faisal; Amyotte, Paul

    2015-07-01

    Compared to the remarkable progress in risk analysis of normal accidents, the risk analysis of major accidents has not been so well-established, partly due to the complexity of such accidents and partly due to low probabilities involved. The issue of low probabilities normally arises from the scarcity of major accidents' relevant data since such accidents are few and far between. In this work, knowing that major accidents are frequently preceded by accident precursors, a novel precursor-based methodology has been developed for likelihood modeling of major accidents in critical infrastructures based on a unique combination of accident precursor data, information theory, and approximate reasoning. For this purpose, we have introduced an innovative application of information analysis to identify the most informative near accident of a major accident. The observed data of the near accident were then used to establish predictive scenarios to foresee the occurrence of the major accident. We verified the methodology using offshore blowouts in the Gulf of Mexico, and then demonstrated its application to dam breaches in the United Sates. © 2015 Society for Risk Analysis.

  4. Return on experience on nuclear accidents

    International Nuclear Information System (INIS)

    Barre, Bertrand

    2015-09-01

    After a presentation of the International Nuclear and radiological Events Scale (INES scale), of its levels and criteria, this article proposes brief recalls of some nuclear accidents which occurred in nuclear reactors: Chalk River in Canada (1952), Windscale in England (1957), the universal Canadian reactor (NRU in 1958), the SL1 reactor of the Idaho National Laboratory in the USA (1961), the Swiss Lucens reactor (1969), Saint-Laurent des Eaux in France (1969 and 1980). More detailed descriptions are then given for the Three Mile Island accident in 1979, the Chernobyl accident in 1986, and the Fukushima accident in 2011. The main causes of these accidents are identified: loss of control of chain reaction, cooling defect on a stopped reactor, cooling defect on an operated reactor. Some lessons are drawn from these facts, and some characteristics of the EPR are outlined with respect with problems encountered in these accidents

  5. Accident scenario diagnostics with neural networks

    International Nuclear Information System (INIS)

    Guo, Z.

    1992-01-01

    Nuclear power plants are very complex systems. The diagnoses of transients or accident conditions is very difficult because a large amount of information, which is often noisy, or intermittent, or even incomplete, need to be processed in real time. To demonstrate their potential application to nuclear power plants, neural networks axe used to monitor the accident scenarios simulated by the training simulator of TVA's Watts Bar Nuclear Power Plant. A self-organization network is used to compress original data to reduce the total number of training patterns. Different accident scenarios are closely related to different key parameters which distinguish one accident scenario from another. Therefore, the accident scenarios can be monitored by a set of small size neural networks, called modular networks, each one of which monitors only one assigned accident scenario, to obtain fast training and recall. Sensitivity analysis is applied to select proper input variables for modular networks

  6. On high-temperature reactor accident topology

    International Nuclear Information System (INIS)

    Fassbender, J.; Kroeger, W.; Wolters, J.

    1981-01-01

    American and German risk studies for an HTGR and independent investigations of hypothetical accident sequences led to a fundamental understanding of the topology of HTGR accident sequences. The dominating importance of core heat-up accidents was confirmed and the initiating events were identified. Complications of core heat-up accidents by air or water ingress are of minor importance for the risk, whereas the long-term development of accidents during days and weeks plays an important role for the environmental impact. The risk caused by an HTGR at a German site cannot yet be determined exactly, because no modern German HTGR design has passed a licensing procedure. Cautious estimates show that risk will appear to be substantially smaller than the LWR risk. The main reasons are the considerably reduced release of fission procucts and the slow development of core heat-up accidents leaving much time for measures which reduce the risk. (orig.) [de

  7. Safety climate and accidents at work

    DEFF Research Database (Denmark)

    Ajslev, Jeppe; Dastjerdi, Efat Lali; Dyreborg, Johnny

    2017-01-01

    Aim: Occupational safety climate is utilized as a way to measure the risk of accidents and injuries at work. This study investigates which factors are associated with safety climate and accidents at work. Methods: In the 2012 round of the Danish Work Environment and Health Study, 15,144 workers...... from the general working population of Denmark replied to questions about safety climate and accidents at work. Mutually adjusted logistic regression analyses determined the association between variables. Results: Within the last year, 5.7% had experienced an accident resulting in sickness absence....... The number of safety climate problems was progressively associated with the odds ratio (OR) for accidents. For one safety climate problem the OR for accidents was 2.01 (95% CI 1.67–2.42), for four or more safety climate problems the OR was 4.57 (95% CI 3.64–5.74). Young workers (18–24 years) had higher odds...

  8. Computer Based Road Accident Reconstruction Experiences

    Directory of Open Access Journals (Sweden)

    Milan Batista

    2005-03-01

    Full Text Available Since road accident analyses and reconstructions are increasinglybased on specific computer software for simulationof vehicle d1iving dynamics and collision dynamics, and forsimulation of a set of trial runs from which the model that bestdescribes a real event can be selected, the paper presents anoverview of some computer software and methods available toaccident reconstruction experts. Besides being time-saving,when properly used such computer software can provide moreauthentic and more trustworthy accident reconstruction, thereforepractical experiences while using computer software toolsfor road accident reconstruction obtained in the TransportSafety Laboratory at the Faculty for Maritime Studies andTransport of the University of Ljubljana are presented and discussed.This paper addresses also software technology for extractingmaximum information from the accident photo-documentationto support accident reconstruction based on the simulationsoftware, as well as the field work of reconstruction expertsor police on the road accident scene defined by this technology.

  9. The Chernobyl reactor accident - a non-accidential accident

    International Nuclear Information System (INIS)

    Zischka, A.

    1987-01-01

    Freedom and independence are reserved but for countries constantly succeeding in maintaining their energy supplies without the help of others. Due to the fact that the political decision makers of the Soviet Union, too, are aware of this truth there is more to the Chernobyl reactor accident than the mere effects of the fallout. The real consequences of the reactor accident had already been anticipated beforehand by the media of the Western world. With the voters already rattled the nuclear phaseout is constantly talked about in all political parties. Once again the law of action passes over to politicians instead of to technology and its responsible experts. Zischka proves this phenomenon in the behaviour towards Soviet reactions having been existed before and shows it to be going back to an old tradition: Already in the reign of the czar the Western neighbours were induced to react in an inadequate manner and thus excert a decisive influence on world politics. The emotional effect of Chernobyl dominates. Unless reason will gain the upper hand the dangers of this emotional effect may turn out to be uncontrollable. (orig./HP) [de

  10. COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

    Energy Technology Data Exchange (ETDEWEB)

    S.O. Bader

    1999-10-18

    The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

  11. COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

    International Nuclear Information System (INIS)

    S.O. Bader

    1999-01-01

    The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

  12. Synergy effect in accident simulation

    International Nuclear Information System (INIS)

    Alba, C.; Carlin, F.; Chenion, J.; Gaussens, G.; Le Meur, M.; Petitjean, M.

    1984-05-01

    Accidental breaking of PWR coolant canalization would entail water vaporization into confinement enclosure. Equipments would be simultaneously subjected to temperature and pressure increase, chemical spray, and radiation action of reactor core products. Some equipments have to work after accident in order to stop reactor running and blow out water calories. Usually, in France, accident simulation tests are carried out sequentialy: irradiation followed by thermodynamical and chemical tests. Equipments working is essentially due to those polymer materials behaviour. Is the polymers behaviour the same when they are either subjected to sequential test, or an accident (simultaneous action of irradiation and thermodynamical and chemical sequence). In order to answer to this question, nine polymer materials were subjected to simultaneous and sequential test in CESAR cell. Experiments were carried out in CESAR device with thermodynamical chocks and a temperature and pressure decrease profil in presence or without irradiation. So, the test is either simultaneous or sequential. Mechanical properties change are determined for the following polymeric materials. Two polyamide-imide varnishes used in motors and coils; one epoxydic resin, glass fiber charged (electrical insulating); polyphenylene sulfide, glass fiber charged, the Ryton R4 (electrical insulating); three elastomeric materials: Hypalon, fire proof by bromine or by alumina EPDM (cables jacket); VAMAC which is a polyethylene methyl polymethacrylate copolymer; then a silicon thermoset material glass fiber charged (electrical insulating). After test, usually, mechanical and electrical properties change of polymer materials show sequential experiment is more severe than simultaneous test however, Hypalon does not follow this law. For this polymer simultaneous test appears more severe than sequential experiment [fr

  13. Molecular and clinical profile of von Willebrand disease in Spain (PCM-EVW-ES): comprehensive genetic analysis by next-generation sequencing of 480 patients.

    Science.gov (United States)

    Borràs, Nina; Batlle, Javier; Pérez-Rodríguez, Almudena; López-Fernández, María Fernanda; Rodríguez-Trillo, Ángela; Lourés, Esther; Cid, Ana Rosa; Bonanad, Santiago; Cabrera, Noelia; Moret, Andrés; Parra, Rafael; Mingot-Castellano, María Eva; Balda, Ignacia; Altisent, Carme; Pérez-Montes, Rocío; Fisac, Rosa María; Iruín, Gemma; Herrero, Sonia; Soto, Inmaculada; de Rueda, Beatriz; Jiménez-Yuste, Víctor; Alonso, Nieves; Vilariño, Dolores; Arija, Olga; Campos, Rosa; Paloma, María José; Bermejo, Nuria; Berrueco, Rubén; Mateo, José; Arribalzaga, Karmele; Marco, Pascual; Palomo, Ángeles; Sarmiento, Lizheidy; Iñigo, Belén; Nieto, María Del Mar; Vidal, Rosa; Martínez, María Paz; Aguinaco, Reyes; César, Jesús María; Ferreiro, María; García-Frade, Javier; Rodríguez-Huerta, Ana María; Cuesta, Jorge; Rodríguez-González, Ramón; García-Candel, Faustino; Cornudella, Rosa; Aguilar, Carlos; Vidal, Francisco; Corrales, Irene

    2017-12-01

    Molecular diagnosis of patients with von Willebrand disease is pending in most populations due to the complexity and high cost of conventional molecular analyses. The need for molecular and clinical characterization of von Willebrand disease in Spain prompted the creation of a multicenter project (PCM-EVW-ES) that resulted in the largest prospective cohort study of patients with all types of von Willebrand disease. Molecular analysis of relevant regions of the VWF , including intronic and promoter regions, was achieved in the 556 individuals recruited via the development of a simple, innovative, relatively low-cost protocol based on microfluidic technology and next-generation sequencing. A total of 704 variants (237 different) were identified along VWF , 155 of which had not been previously recorded in the international mutation database. The potential pathogenic effect of these variants was assessed by in silico analysis. Furthermore, four short tandem repeats were analyzed in order to evaluate the ancestral origin of recurrent mutations. The outcome of genetic analysis allowed for the reclassification of 110 patients, identification of 37 asymptomatic carriers (important for genetic counseling) and re-inclusion of 43 patients previously excluded by phenotyping results. In total, 480 patients were definitively diagnosed. Candidate mutations were identified in all patients except 13 type 1 von Willebrand disease, yielding a high genotype-phenotype correlation. Our data reinforce the capital importance and usefulness of genetics in von Willebrand disease diagnostics. The progressive implementation of molecular study as the first-line test for routine diagnosis of this condition will lead to increasingly more personalized and effective care for this patient population. Copyright© 2017 Ferrata Storti Foundation.

  14. Synthesis and thermal properties of the MA/HDPE composites with nano-additives as form-stable PCM with improved thermal conductivity

    International Nuclear Information System (INIS)

    Tang, Yaojie; Su, Di; Huang, Xiang; Alva, Guruprasad; Liu, Lingkun; Fang, Guiyin

    2016-01-01

    Highlights: • MA/HDPE composites with nano-additives were prepared for thermal conductivity enhancement. • Microstructure and chemical structure of the FSPCM were analyzed. • Thermal properties and thermal reliability of the FSPCM were investigated. • Thermal conductivity of the FSPCM can be enhanced by adding NAO and NG. - Abstract: For the purpose of improving the thermal conductivity of the form–stable phase change materials (FSPCM), two types of nano–powders with high thermal conductivity were added into the samples. In the modified FSPCM, myristic acid (MA) was used as a solid–liquid phase change material (PCM), high density polyethylene (HDPE) acted as supporting material to prevent the leakage of the melted MA. Nano–Al 2 O 3 (NAO) and nano–graphite (NG) were the additives for thermal conductivity enhancement. Scanning electronic microscope (SEM), Fourier transformation infrared spectroscope (FT–IR) and X-ray diffractometer (XRD) were used to analyze the microstructure, chemical structure and crystalline phase of the samples, respectively. Furthermore, the specific latent heat and phase transition temperature, thermal conductivity and thermal reliability were investigated using differential scanning calorimeter (DSC), thermal conductivity meter and thermo–gravimetric analyzer (TGA). The results showed that the MA was uniformly absorbed in the HDPE matrices and there was no leakage during the melting process when the mass fraction of the MA in the MA/HDPE composite was less than 70%. The DSC results revealed that the modified FSPCM have a constant phase change temperature and high specific latent heat. The thermal conductivity of the FSPCM was measured in the solid (30 °C) and liquid (60 °C) states of the MA. When the mass fraction of nano–powder additives is 12%, the thermal conductivities of the FSPCM increase by 95% (NAO) and 121% (NG) at 30 °C. It is anticipated that the FSPCM possess a potential application for thermal energy

  15. Workplace Accidents and Self-Organized Criticality

    OpenAIRE

    Mauro, John C.; Diehl, Brett; Marcellin, Richard F.; Vaughn, Daniel J.

    2018-01-01

    The occurrence of workplace accidents is described within the context of self-organized criticality, a theory from statistical physics that governs a wide range of phenomena across physics, biology, geosciences, economics, and the social sciences. Workplace accident data from the U.S. Bureau of Labor Statistics reveal a power-law relationship between the number of accidents and their severity as measured by the number of days lost from work. This power-law scaling is indicative of workplace a...

  16. Four years after the JCO criticality accident

    International Nuclear Information System (INIS)

    Sumita, Kenji

    2003-01-01

    It has been about four years since the first criticality accident in Japan. The JCO accident site was not so far from this auditorium. I have been asked to give a short review of important results from the various technical investigations on the accident that have been performed during the past four years. I will also give a short introduction to the changes that have been made in the nuclear safety regulation systems of the Japanese Government. (author)

  17. Kyshtym riddle: possible kind of the accident

    International Nuclear Information System (INIS)

    Ballereau, P.

    1988-01-01

    It can been postulated from varied rumors, soviet testimonies, analysis of radioecological russian publications that a serious radiological accident occurred in late 1957 - early 1958 in the Oural mountains. Isotopic ratio 90 Sr/ 137 Cs in the environment following the accident was abnormally high. Several types of accidents has been postulated; the more credible event is an explosion in a storage tank containing dried high activity wastes and NH 4 N0 3 , from which 137 Cs had been extracted [fr

  18. The radiological accident in Goiania

    International Nuclear Information System (INIS)

    1988-01-01

    The report is based on a meeting held in Brazil, 19-27 July 1988. It describes how the accident occurred, examines how it was managed and how its consequences were contained, and sets out observations and recommendations based upon lessons learned. Many people received large doses of radiation, due to both external and internal exposure. Four of the casualties ultimately died and 28 people suffered radiation burns. Residences and public places were contaminated. The decontamination necessitated the demolition of seven residences and various other buildings, and the removal of the topsoil from large areas. In total 3,500 m 3 of radioactive waste was generated. Refs, figs, tabs and photographs

  19. HTR-10 severe accident management

    International Nuclear Information System (INIS)

    Xu Yuanhui; Sun Yuliang

    1997-01-01

    The High Temperature Gas-cooled Reactor (HTR-10) is under construction at the Institute of Nuclear Energy Technology site northwest of Beijing. This 10 MW thermal plant utilizes a pebble bed high temperature gas cooled reactor for a large range of applications such as electricity generation, steam and district heat generation, gas turbine and steam turbine combined cycle and process heat for methane reforming. The HTR-10 is the first high temperature gas cooled reactor to be licensed in China. This paper describes the safety characteristics and design criteria for the HTR-10 as well as the accident management and analysis required for the licensing process. (author)

  20. Elements to diminish radioactive accidents

    International Nuclear Information System (INIS)

    Cortes I, M.E.; Ramirez G, F.P.

    1998-01-01

    In this work it is presented an application of the cause-effect diagram method or Ichikawa method identifying the elements that allow to diminish accidents when the radioactive materials are transported. It is considered the transport of hazardous materials which include radioactive materials in the period: December 1996 until March 1997. Among the identified elements by this method it is possible to mention: the road type, the radioactive source protection, the grade driver responsibility and the preparation that the OEP has in the radioactive material management. It is showed the differences found between the country inner roads and the Mexico City area. (Author)