A study on radiation technological degradation of organic chloride wastewater-Exemplified by TCE and PCE

Energy Technology Data Exchange (ETDEWEB)

Huang, S.-K.; Hsieh, L.-L. [Institute of Radiological Science, Central Taiwan University of Science and Technology, No. 11, Buzih Lane, Beitun District, Taichung City 40601, Taiwan (China); Chen, C.-C. [Isotope Application Division, Institute of Nuclear Energy Research, Taiwan (China); Lee, P.-H. [Institute of Radiological Science, Central Taiwan University of Science and Technology, No. 11, Buzih Lane, Beitun District, Taichung City 40601, Taiwan (China); Hsieh, B.-T. [Institute of Radiological Science, Central Taiwan University of Science and Technology, No. 11, Buzih Lane, Beitun District, Taichung City 40601, Taiwan (China)], E-mail: bthsieh@ctust.edu.tw

2009-07-15

This paper describes the potential of using gamma radiation technology to degrade trichloroethylene (TCE) and perchloroethylene (PCE) wastewater. The experimental method is divided into two parts: (1) using the {gamma}-ray to irradiate the TCE and PCE solution, the dose-rate is 10 Gy/minute, the irradiation dosage is 0-2.5 kGy and (2) self-making the UV irradiation system, the tube specification is 254 nm and 6 W, and turning on 8 tubes at the same time to make the irradiation. The efficiency of degradation ratio for {gamma}-ray is better than UV in the range of 0.1-250 ppm; for example, as for the concentration of 0.1 ppm, when TCE is degraded to D{sub 90} and T{sub 90}, the {gamma}-ray only needed 46.7 Gy and took about 4.67 minutes, but UV needed to take about 28.1 minutes. The dose-concentration equations of TCE and PCE are: TCE: y=44.58+8.832x, R{sup 2}=0.999; and PCE: y=81.33+12.81x, R{sup 2}=0.997. We verified that the radiation technology is able to effectively degrade the organic chlorine wastewater without yielding the secondary pollution, and the TCE and PCE that degraded by using {gamma}-ray will be reached US-EPA and Taiwan Effluent Standard (5 ppb)

A study on radiation technological degradation of organic chloride wastewater--exemplified by TCE and PCE.

Science.gov (United States)

Huang, Sheng-Kai; Hsieh, Ling-Ling; Chen, Chia-Chieh; Lee, Po-Hsiu; Hsieh, Bor-Tsung

2009-01-01

This paper describes the potential of using gamma radiation technology to degrade trichloroethylene (TCE) and perchloroethylene (PCE) wastewater. The experimental method is divided into two parts: (1) using the gamma-ray to irradiate the TCE and PCE solution, the dose-rate is 10Gy/minute, the irradiation dosage is 0-2.5kGy and (2) self-making the UV irradiation system, the tube specification is 254nm and 6W, and turning on 8 tubes at the same time to make the irradiation. The efficiency of degradation ratio for gamma-ray is better than UV in the range of 0.1-250ppm; for example, as for the concentration of 0.1ppm, when TCE is degraded to D(90) and T(90), the gamma-ray only needed 46.7Gy and took about 4.67 minutes, but UV needed to take about 28.1 minutes. The dose-concentration equations of TCE and PCE are: TCE: y=44.58+8.832x, R(2)=0.999; and PCE: y=81.33+12.81x, R(2)=0.997. We verified that the radiation technology is able to effectively degrade the organic chlorine wastewater without yielding the secondary pollution, and the TCE and PCE that degraded by using gamma-ray will be reached US-EPA and Taiwan Effluent Standard (5ppb).

A study on radiation technological degradation of organic chloride wastewater-Exemplified by TCE and PCE

International Nuclear Information System (INIS)

Huang, S.-K.; Hsieh, L.-L.; Chen, C.-C.; Lee, P.-H.; Hsieh, B.-T.

2009-01-01

This paper describes the potential of using gamma radiation technology to degrade trichloroethylene (TCE) and perchloroethylene (PCE) wastewater. The experimental method is divided into two parts: (1) using the γ-ray to irradiate the TCE and PCE solution, the dose-rate is 10 Gy/minute, the irradiation dosage is 0-2.5 kGy and (2) self-making the UV irradiation system, the tube specification is 254 nm and 6 W, and turning on 8 tubes at the same time to make the irradiation. The efficiency of degradation ratio for γ-ray is better than UV in the range of 0.1-250 ppm; for example, as for the concentration of 0.1 ppm, when TCE is degraded to D 90 and T 90 , the γ-ray only needed 46.7 Gy and took about 4.67 minutes, but UV needed to take about 28.1 minutes. The dose-concentration equations of TCE and PCE are: TCE: y=44.58+8.832x, R 2 =0.999; and PCE: y=81.33+12.81x, R 2 =0.997. We verified that the radiation technology is able to effectively degrade the organic chlorine wastewater without yielding the secondary pollution, and the TCE and PCE that degraded by using γ-ray will be reached US-EPA and Taiwan Effluent Standard (5 ppb).

Air purification from TCE and PCE contamination in a hybrid bioreactors and biofilter integrated system.

Science.gov (United States)

Tabernacka, Agnieszka; Zborowska, Ewa; Lebkowska, Maria; Borawski, Maciej

2014-01-15

A two-stage waste air treatment system, consisting of hybrid bioreactors (modified bioscrubbers) and a biofilter, was used to treat waste air containing chlorinated ethenes - trichloroethylene (TCE) and tetrachloroethylene (PCE). The bioreactor was operated with loadings in the range 0.46-5.50gm(-3)h(-1) for TCE and 2.16-9.02gm(-3)h(-1) for PCE. The biofilter loadings were in the range 0.1-0.97gm(-3)h(-1) for TCE and 0.2-2.12gm(-3)h(-1) for PCE. Under low pollutant loadings, the efficiency of TCE elimination was 23-25% in the bioreactor and 54-70% in the biofilter. The efficiency of PCE elimination was 44-60% in the bioreactor and 50-75% in the biofilter. The best results for the bioreactor were observed one week after the pollutant loading was increased. However, the process did not stabilize. In the next seven days contaminant removal efficiency, enzymatic activity and biomass content were all diminished. Copyright © 2013 Elsevier B.V. All rights reserved.

Effect of emplaced nZVI mass and groundwater velocity on PCE dechlorination and hydrogen evolution in water-saturated sand

International Nuclear Information System (INIS)

Kim, Hye-Jin; Leitch, Megan; Naknakorn, Bhanuphong; Tilton, Robert D.; Lowry, Gregory V.

2017-01-01

Highlights: • Reactivity of nZVI increased linearly with nZVI concentration above 10 g/L, but was non-linear below 10 g/L. • nZVI reactivity with PCE is more sensitive to solution redox potential than solution pH. • Mass transfer limits the reactivity of emplaced nZVI under typical groundwater flow velocity. • Lowering pH increases H_2 evolution from nZVI more than reactivity with PCE. • Design of nZVI remediation strategies should consider mass loading and flow velocity on performance and lifetime. - Abstract: The effect of nZVI mass loading and groundwater velocity on the tetrachloroethylene (PCE) dechlorination rate and the hydrogen evolution rate for poly(maleic acid-co-olefin) (MW = 12 K) coated nZVI was examined. In batch reactors, the PCE reaction rate constant (3.7 × 10"−"4 L hr"−"1 m"−"2) and hydrogen evolution rate constant (1.4 nanomol L hr"−"1 m"−"2) were independent of nZVI concentration above 10 g/L, but the PCE dechlorination rate decreased and the hydrogen evolution rate increased for nZVI concentration below 10 g/L. The nonlinearity between nZVI mass loading and PCE dechlorination and H_2 evolution was explained by differences in pH and E_h at each nZVI mass loading; PCE reactivity increased when solution E_h decreased, and the H_2 evolution rate increased with decreasing pH. Thus, nZVI mass loading of <5 g/L yields lower reactivity with PCE and lower efficiency of Fe° utilization than for higher nZVI mass loading. The PCE dechlorination rate increased with increasing pore-water velocity, suggesting that mass transfer limits the reaction at low porewater velocity. Overall, this work suggests that design of nZVI-based reactive barriers for groundwater treatment should consider the non-linear effects of both mass loading and flow velocity on performance and expected reactive lifetime.

Effect of emplaced nZVI mass and groundwater velocity on PCE dechlorination and hydrogen evolution in water-saturated sand

Energy Technology Data Exchange (ETDEWEB)

Kim, Hye-Jin [Civil & Environmental Engineering, Carnegie Mellon University, Pittsburgh, PA 15213-3890 (United States); Chemical Research Division, Environmental Health Research Department, National Institute of Environmental Research, Incheon 404-708 (Korea, Republic of); Leitch, Megan [Civil & Environmental Engineering, Carnegie Mellon University, Pittsburgh, PA 15213-3890 (United States); Center for Environmental Implications of Nanotechnology, Carnegie Mellon University, Pittsburgh, PA 15213-3890 (United States); Naknakorn, Bhanuphong [Civil & Environmental Engineering, Carnegie Mellon University, Pittsburgh, PA 15213-3890 (United States); Tilton, Robert D. [Chemical Engineering, Carnegie Mellon University, Pittsburgh, PA 15213-3890 (United States); Biomedical Engineering, Carnegie Mellon University, Pittsburgh, PA 15213-3890 (United States); Center for Environmental Implications of Nanotechnology, Carnegie Mellon University, Pittsburgh, PA 15213-3890 (United States); Lowry, Gregory V., E-mail: glowry@cmu.edu [Civil & Environmental Engineering, Carnegie Mellon University, Pittsburgh, PA 15213-3890 (United States); Chemical Engineering, Carnegie Mellon University, Pittsburgh, PA 15213-3890 (United States); Center for Environmental Implications of Nanotechnology, Carnegie Mellon University, Pittsburgh, PA 15213-3890 (United States)

2017-01-15

Highlights: • Reactivity of nZVI increased linearly with nZVI concentration above 10 g/L, but was non-linear below 10 g/L. • nZVI reactivity with PCE is more sensitive to solution redox potential than solution pH. • Mass transfer limits the reactivity of emplaced nZVI under typical groundwater flow velocity. • Lowering pH increases H{sub 2} evolution from nZVI more than reactivity with PCE. • Design of nZVI remediation strategies should consider mass loading and flow velocity on performance and lifetime. - Abstract: The effect of nZVI mass loading and groundwater velocity on the tetrachloroethylene (PCE) dechlorination rate and the hydrogen evolution rate for poly(maleic acid-co-olefin) (MW = 12 K) coated nZVI was examined. In batch reactors, the PCE reaction rate constant (3.7 × 10{sup −4} L hr{sup −1} m{sup −2}) and hydrogen evolution rate constant (1.4 nanomol L hr{sup −1} m{sup −2}) were independent of nZVI concentration above 10 g/L, but the PCE dechlorination rate decreased and the hydrogen evolution rate increased for nZVI concentration below 10 g/L. The nonlinearity between nZVI mass loading and PCE dechlorination and H{sub 2} evolution was explained by differences in pH and E{sub h} at each nZVI mass loading; PCE reactivity increased when solution E{sub h} decreased, and the H{sub 2} evolution rate increased with decreasing pH. Thus, nZVI mass loading of <5 g/L yields lower reactivity with PCE and lower efficiency of Fe° utilization than for higher nZVI mass loading. The PCE dechlorination rate increased with increasing pore-water velocity, suggesting that mass transfer limits the reaction at low porewater velocity. Overall, this work suggests that design of nZVI-based reactive barriers for groundwater treatment should consider the non-linear effects of both mass loading and flow velocity on performance and expected reactive lifetime.

Solvent extraction of elemental sulfur from coal and a determination of its source using stable sulfur isotopes

Science.gov (United States)

Hackley, Keith C.; Buchanan, D.H.; Coombs, K.; Chaven, C.; Kruse, C.W.

1990-01-01

Hot tetrachloroethene (perchloroethylene, PCE) extracts significant amounts of elemental sulfur (So) from weathered coals but not from pristine coals. The objective of this study was to determine whether So extracted by PCE is an oxidation product of pyrite or whether it originates in some way from unstable, organically-bound sulfur. The isotopic composition of the PCE-extracted So was compared to the isotopic compositions of the pyritic and the organic sulfur in a coal. The So was shown to have an isotopic signature similar to the pyritic sulfur. Additionally, the isotopic differences observed between the pyritic, So and sulfatic sulfur were consistent with bacterial mediated oxidation of sulfide sulfur (pyrite) as the source of both the sulfatic and elemental sulfur. ?? 1990.

Use of in situ chemical oxidation with permanganate in PCE-contaminated clayey till with sand lenses

DEFF Research Database (Denmark)

Hønning, Jirij

Klorerede stoffer som perklorethen (PCE) og triklorethen (TCE) har været benyttet i stort omfang verden over. PCE er primært kendt for sit omfattende brug ved rensning af tøj, hvorimod TCE primært er benyttet som affedtningsmiddel. På grund af den omfattende brug er klorerede stoffer ofte fundet ...

PCE and BNS admixture adsorption in sands with different composition and particle size distribution

International Nuclear Information System (INIS)

Alonso, M.M.; Martínez-Gaitero, R.; Gismera-Diez, S.; Puertas, F.

2017-01-01

The choice of a superplasticiser (SP) for concrete is of great complexity, as it is well known that properties of the end product are related to admixture and its compatibility with concrete components. Very few studies have been conducted on the compatibility between SPs and the sand of mortars and concretes, however. Practical experience has shown that sand fineness and mineralogical composition affect water demand and admixture consumption. Clay-containing sand has been found also to adsorb SPs, reducing the amount available in solution for adsorption by the cement. This study analysed the isotherms for PCE and BNS superplasticiser adsorption on four sands with different fineness and compositions commonly used to prepare mortars and concretes. BNS-based SP did not adsorb on sands, while PCE-based admixtures exhibited variable adsorption depending on different factors. The adsorption curves obtained revealed that the higher the sand fineness, the finer the particle size distribution and the higher the clay material, the greater was PCE admixture adsorption/ consumption. [es

PCE and BNS admixture adsorption in sands with different composition and particle size distribution

Directory of Open Access Journals (Sweden)

M. M. Alonso

2017-02-01

Full Text Available The choice of a superplasticiser (SP for concrete is of great complexity, as it is well known that properties of the end product are related to admixture and its compatibility with concrete components. Very few studies have been conducted on the compatibility between SPs and the sand of mortars and concretes, however. Practical experience has shown that sand fineness and mineralogical composition affect water demand and admixture consumption. Clay-containing sand has been found also to adsorb SPs, reducing the amount available in solution for adsorption by the cement. This study analysed the isotherms for PCE and BNS superplasticiser adsorption on four sands with different fineness and compositions commonly used to prepare mortars and concretes. BNS-based SP did not adsorb on sands, while PCE-based admixtures exhibited variable adsorption depending on different factors. The adsorption curves obtained revealed that the higher the sand fineness, the finer the particle size distribution and the higher the clay material, the greater was PCE admixture adsorption/ consumption.

Solvent extraction of elemental sulfur from coal and a determination of its source using stable sulfur isotopes

Energy Technology Data Exchange (ETDEWEB)

Hackley, K.C.; Buchanan, D.H.; Coombs, K.; Chaven, C.; Kruse, C.W. (Eastern Illinois University, Charleston, IL (USA). Chemistry Dept.)

1990-01-01

Hot tetrachloroethene (perchloroethylen PCE) extracts significant amounts of elemental sulfur (S{sup o}) from weathered coals but not from pristine coals. The objective of this study was to determine whether S{sup o} extracted by PCE is an oxidation product of pyrite or whether it originates in some way from unstable, organically-bound sulfur. The isotopic composition of the PCE-extracted S{sup o} was compared to the isotopic compositions of the pyritic and the organic sulfur in a coal. The S{sup o} was shown to have an isotopic signature similar to the pyritic sulfur. Additionally, the isotopic differences observed between the pyritic, S{sup o} and sulfatic sulfur were consistent with bacterial mediated oxidation of sulfide sulfur (pyrite) as the source of both the sulfatic and elemental sulfur. 21 refs., 2 tabs.

Development of emergency response training program for on-site commanders (2). Extraction of non-technical skills

International Nuclear Information System (INIS)

Matsui, Yuko; Hikono, Masaru; Iwasaki, Mari; Morita, Miduho

2017-01-01

This study aimed at characterizing a non-technical skill exercise for on-site managers in charge of initial response at an emergency response center by extracting and clarifying the behavior examples of non-technical skills shown in the exercise scenario. From video observations, the non-technical skill examples were identified from seven of the eight non-technical skill categories which had been defined when the training program was developed. At the same time, the limitation when extracting the cases by observations was identified. The extracted non-technical skill cases are expected to be used for characterizing exercise scenarios, as well as provide knowledge to raise the awareness of exercise participants. (author)

Kinetic modeling and simulation of PCE and TCE removal in aqueous solutions by electron-beam irradiation

International Nuclear Information System (INIS)

Nickelsen, Michael G.; Cooper, William J.; Secker, David A.; Rosocha, Louis A.; Kurucz, Charles N.; Waite, Thomas D.

2002-01-01

The irradiation of aqueous solutions of TCE and PCE using a high-energy electron-beam results in the rapid decomposition of both chemicals. It is known that both TCE and PCE react with the aqueous electron and the hydroxyl radical with bimolecular rate constants greater than 10 9 M -1 s -1 for each reaction. The fact that high-energy electrons produce significant concentrations of both e aq - and ·OH radicals in water makes it an effective process for the removal of TCE and PCE from aqueous solution. We have employed steady state and computer-based chemical kinetic models to simulate and better understand the chemistry and kinetics of e-beam irradiation when applied to natural water systems. Model results were benchmarked to experimental data, allowing for the optimization of the reaction of DOC with the ·OH radical. Values for the associated second-order reaction rate constant were found to be 2.5x10 8 and 4.0x10 8 M -1 s -1 , consistent with reported values for k OH,DOC . The models were also used to investigate the possibility of incomplete irradiation during treatment and the presence of proposed chemical reactions of by-products. The reactions involve radicals and radical-adduct species formed by the reaction of TCE and PCE with the hydroxyl radical

Transformation efficiency and formation of transformation products during photochemical degradation of TCE and PCE at micromolar concentrations.

Science.gov (United States)

Dobaradaran, Sina; Lutze, Holger; Mahvi, Amir Hossein; Schmidt, Torsten C

2014-01-08

Trichloroethene and tetrachloroethene are the most common pollutants in groundwater and two of the priority pollutants listed by the U.S. Environmental Protection Agency. In previous studies on TCE and PCE photolysis and photochemical degradation, concentration ranges exceeding environmental levels by far with millimolar concentrations of TCE and PCE have been used, and it is not clear if the obtained results can be used to explain the degradation of these contaminants at more realistic environmental concentration levels. Experiments with micromolar concentrations of TCE and PCE in aqueous solution using direct photolysis and UV/H2O2 have been conducted and product formation as well as transformation efficiency have been investigated. SPME/GC/MS, HPLC/UV and ion chromatography with conductivity detection have been used to determine intermediates of degradation. The results showed that chloride was a major end product in both TCE and PCE photodegradation. Several intermediates such as formic acid, dichloroacetic acid, dichloroacetaldehyede, chloroform, formaldehyde and glyoxylic acid were formed during both, UV and UV/H2O2 treatment of TCE. However chloroacetaldehyde and chloroacetic acid were only detected during direct UV photolysis of TCE and oxalic acid was only formed during the UV/H2O2 process. For PCE photodegradation, formic acid, di- and trichloroacetic acids were detected in both UV and UV/H2O2 systems, but formaldehyde and glyoxylic acid were only detected during direct UV photolysis. For water treatment UV/H2O2 seems to be favorable over direct UV photolysis because of its higher degradation efficiency and lower risk for the formation of harmful intermediates.

Effects of microarrangement of solid particles on PCE migration and its remediation in porous media

Science.gov (United States)

Wu, Ming; Wu, Jianfeng; Wu, Jichun; Hu, Bill X.

2018-02-01

Groundwater can be stored abundantly in granula-composed aquifers with high permeability. The microstructure of granular materials has important effect on the permeability of aquifers and the contaminant migration and remediation in aquifers is also influenced by the characteristics of porous media. In this study, two different microscale arrangements of sand particles are compared to reveal the effects of microstructure on the contaminant migration and remediation. With the help of fractal theory, the mathematical expressions of permeability and entry pressure are conducted to delineate granular materials with regular triangle arrangement (RTA) and square pitch arrangement (SPA) at microscale. Using a sequential Gaussian simulation (SGS) method, a synthetic heterogeneous site contaminated by perchloroethylene (PCE) is then used to investigate the migration and remediation affected by the two different microscale arrangements. PCE is released from an underground storage tank into the aquifer and the surfactant is used to clean up the subsurface contamination. Results suggest that RTA can not only cause more groundwater contamination, but also make remediation become more difficult. The PCE remediation efficiency of 60.01-99.78 % with a mean of 92.52 and 65.53-99.74 % with a mean of 95.83 % is achieved for 200 individual heterogeneous realizations based on the RTA and SPA, respectively, indicating that the cleanup of PCE in aquifer with SPA is significantly easier. This study leads to a new understanding of the microstructures of porous media and demonstrates how microscale arrangements control contaminant migration in aquifers, which is helpful to design successful remediation scheme for underground storage tank spill.

Radioprotective effects of hawthorn fruit extract against gamma irradiation in mouse bone marrow cells

International Nuclear Information System (INIS)

Hosseinimehr, S.J.; Azadbakht, M.; Mousavi, S.M.; Mahmoudzadeh, A.; Akhlaghpoor, S.

2007-01-01

The radioprotective effect of hawthorn (Crataegus microphylla) fruit extract against genotoxicity induced by gamma irradiation has been investigated in mouse bone marrow cells. A single intraperitoneal (ip) administration of hawthorn extract at doses of 25, 50, 100 and 200 mg/kg 1 h prior to gamma irradiation (2 Gy) reduced the frequencies of micronucleated polychromatic erythrocytes (MnPCEs). All four doses of hawthorn extract significantly reduced the frequencies of MnPCEs and increased the PCE/PCE+NCE ratio (polychromatic erythrocyte/polychromatic erythrocyte+normochromatic erythrocyte) in mice bone marrow compared with the non drug-treated irradiated control (p<0.02-0.00001). The maximum reduction in MnPCEs was observed in mice treated with extract at a dose of 200 mg/kg. Administration of amifostine at dose 100 mg/kg and hawthorn at dose 200 mg/kg reduced the frequency of MnPCE almost 4.8 and 5.7 fold; respectively, after being exposed to 2 Gy of gamma rays, compare with the irradiated control group. Crataegus extract exhibited concentration-dependent activity on 1, 1-diphenyl 2-picrylhydrazyl free radical showing that Crataegus contained high amounts of phenolic compounds and the high performance liquid chromatography (HPLC) analysis determined that it contained chlorogenic acid, epicatechin and hyperoside. It appeared that hawthorn extract with antioxidant activity reduced the genotoxicity induced by gamma irradiation in bone marrow cells. (author)

Affinity for risky behaviors following prenatal and early childhood exposure to tetrachloroethylene (PCE-contaminated drinking water: a retrospective cohort study

Directory of Open Access Journals (Sweden)

Aschengrau Ann

2011-12-01

Full Text Available Abstract Background Many studies of adults with acute and chronic solvent exposure have shown adverse effects on cognition, behavior and mood. No prior study has investigated the long-term impact of prenatal and early childhood exposure to the solvent tetrachloroethylene (PCE on the affinity for risky behaviors, defined as smoking, drinking or drug use as a teen or adult. Objectives This retrospective cohort study examined whether early life exposure to PCE-contaminated drinking water influenced the occurrence of cigarette smoking, alcohol consumption, and drug use among adults from Cape Cod, Massachusetts. Methods Eight hundred and thirty-one subjects with prenatal and early childhood PCE exposure and 547 unexposed subjects were studied. Participants completed questionnaires to gather information on risky behaviors as a teenager and young adult, demographic characteristics, other sources of solvent exposure, and residences from birth through 1990. PCE exposure was estimated using the U.S. EPA's water distribution system modeling software (EPANET that was modified to incorporate a leaching and transport model to estimate PCE exposures from pipe linings. Results Individuals who were highly exposed to PCE-contaminated drinking water during gestation and early childhood experienced 50-60% increases in the risk of using two or more major illicit drugs as a teenager or as an adult (Relative Risk (RR for teen use = 1.6, 95% CI: 1.2-2.2; and RR for adult use = 1.5, 95% CI: 1.2-1.9. Specific drugs for which increased risks were observed included crack/cocaine, psychedelics/hallucinogens, club/designer drugs, Ritalin without a prescription, and heroin (RRs:1.4-2.1. Thirty to 60% increases in the risk of certain smoking and drinking behaviors were also seen among highly exposed subjects. Conclusions The results of this study suggest that risky behaviors, particularly drug use, are more frequent among adults with high PCE exposure levels during gestation

Spatial and temporal dynamics of organohalide-respiring bacteria in a heterogeneous PCE-DNAPL source zone.

Science.gov (United States)

Cápiro, Natalie L; Löffler, Frank E; Pennell, Kurt D

2015-11-01

Effective treatment of sites contaminated with dense non-aqueous phase liquids (DNAPLs) requires detailed understanding of the microbial community responses to changes in source zone strength and architecture. Changes in the spatial and temporal distributions of the organohalide-respiring Dehalococcoides mccartyi (Dhc) strains and Geobacter lovleyi strain SZ (GeoSZ) were examined in a heterogeneous tetrachloroethene- (PCE-) DNAPL source zone within a two-dimensional laboratory-scale aquifer flow cell. As part of a combined remedy approach, flushing with 2.3 pore volumes (PVs) of 4% (w/w) solution of the nonionic, biodegradable surfactant Tween® 80 removed 55% of the initial contaminant mass, and resulted in a PCE-DNAPL distribution that contained 51% discrete ganglia and 49% pools (ganglia-to-pool ratio of 1.06). Subsequent bioaugmentation with the PCE-to-ethene-dechlorinating consortium BDI-SZ resulted in cis-1,2-dichloroethene (cis-DCE) formation after 1 PV (ca. 7 days), while vinyl chloride (VC) and ethene were detected 10 PVs after bioaugmentation. Maximum ethene yields (ca. 90 μM) within DNAPL pool and ganglia regions coincided with the detection of the vcrA reductive dehalogenase (RDase) gene that exceeded the Dhc 16S rRNA genes by 2.0±1.3 and 4.0±1.7 fold in the pool and ganglia regions, respectively. Dhc and GeoSZ cell abundance increased by up to 4 orders-of-magnitude after 28 PVs of steady-state operation, with 1 to 2 orders-of-magnitude increases observed in close proximity to residual PCE-DNAPL. These observations suggest the involvement of these dechlorinators the in observed PCE dissolution enhancements of up to 2.3 and 6.0-fold within pool and ganglia regions, respectively. Analysis of the solid and aqueous samples at the conclusion of the experiment revealed that the highest VC (≥155 μM) and ethene (≥65 μM) concentrations were measured in zones where Dhc and GeoSZ were predominately attached to the solids. These findings demonstrate

INFLUENCE OF HYDRAULIC RETENTION TIME ON EXTENT OF PCE DECHLORINATION AND PRELIMINARY CHARACTERIZATION OF THE ENRICHMENT CULTURE. (R826694C703)

Science.gov (United States)

The extent of tetrachloroethene (PCE) dechlorination in two chemostats was evaluated as a function of hydraulic retention time (HRT). The inoculum of these chemostats was from an upflow anaerobic sludge blanket (UASB) reactor that rapidly converts PCE to vinyl chloride (VC) an...

Use of technical mixtures of carboxylic acids to the extraction of silver

International Nuclear Information System (INIS)

Smulek, W.

1983-01-01

The application of technical mixtures of carboxylic acids, obtained from a Polish oil mill, to the extraction of silver, gold, and europium is described. The distribution ratio is given as a function of HNO 3 and H 2 SO 4 concentrations, extractant and metal concentrations, and nature of diluent. (author)

PCE dechlorination by non-Dehalococcoides in a microbial electrochemical system.

Science.gov (United States)

Yu, Jaecheul; Park, Younghyun; Nguyen, Van Khanh; Lee, Taeho

2016-08-01

The bioremediation of tetrachloroethene (perchloroethene; PCE) contaminated sites generally requires a supply of some fermentable organic substrates as an electron donor. On the other hand, organic substrates can induce the massive growth of microorganisms around the injection wells, which can foul the contaminated subsurface environment. In this study, PCE dechlorination to ethene was performed in a microbial electrochemical system (MES) using the electrode (a cathode polarized at -500 mV vs. standard hydrogen electrode) as the electron donor. Denaturing gel gradient electrophoresis and pyrosequencing revealed a variety of non-Dehalococcoides bacteria dominant in MES, such as Acinetobacter sp. (25.7 % for AS1 in suspension of M3), Rhodopseudomonas sp. (10.5 % for AE1 and 10.1 % for AE2 in anodic biofilm of M3), Pseudomonas aeruginosa (22.4 % for BS1 in suspension of M4), and Enterobacter sp. (21.7 % for BE1 in anodic biofilm of M4) which are capable of electron transfer, hydrogen production and dechlorination. The Dehalococcoides group, however, was not detected in this system. Therefore, these results suggest that a range of bacterial species outside the Dehalococcoides can play an important role in the microbial electrochemical dechlorination process, which may lead to innovative bioremediation technology.

Identification of TCE and PCE sorption and biodegradation parameters in a sandy aquifer for fate and transport modelling: batch and column studies.

Science.gov (United States)

Kret, E; Kiecak, A; Malina, G; Nijenhuis, I; Postawa, A

2015-07-01

The main aim of this study was to determine the sorption and biodegradation parameters of trichloroethene (TCE) and tetrachloroethene (PCE) as input data required for their fate and transport modelling in a Quaternary sandy aquifer. Sorption was determined based on batch and column experiments, while biodegradation was investigated using the compound-specific isotope analysis (CSIA). The aquifer materials medium (soil 1) to fine (soil 2) sands and groundwater samples came from the representative profile of the contaminated site (south-east Poland). The sorption isotherms were approximately linear (TCE, soil 1, K d = 0.0016; PCE, soil 1, K d = 0.0051; PCE, soil 2, K d = 0.0069) except for one case in which the best fitting was for the Langmuir isotherm (TCE, soil 2, K f = 0.6493 and S max = 0.0145). The results indicate low retardation coefficients (R) of TCE and PCE; however, somewhat lower values were obtained in batch compared to column experiments. In the column experiments with the presence of both contaminants, TCE influenced sorption of PCE, so that the R values for both compounds were almost two times higher. Non-significant differences in isotope compositions of TCE and PCE measured in the observation points (δ(13)C values within the range of -23.6 ÷ -24.3‰ and -26.3 ÷-27.7‰, respectively) indicate that biodegradation apparently is not an important process contributing to the natural attenuation of these contaminants in the studied sandy aquifer.

PCE and BNS admixture adsorption in sands with different composition and particle size distribution; Adsorción de aditivos PCE y BNS en arenas con diferente composición y distribución de tamaño de partículas

Energy Technology Data Exchange (ETDEWEB)

Alonso, M.M.; Martínez-Gaitero, R.; Gismera-Diez, S.; Puertas, F.

2017-07-01

The choice of a superplasticiser (SP) for concrete is of great complexity, as it is well known that properties of the end product are related to admixture and its compatibility with concrete components. Very few studies have been conducted on the compatibility between SPs and the sand of mortars and concretes, however. Practical experience has shown that sand fineness and mineralogical composition affect water demand and admixture consumption. Clay-containing sand has been found also to adsorb SPs, reducing the amount available in solution for adsorption by the cement. This study analysed the isotherms for PCE and BNS superplasticiser adsorption on four sands with different fineness and compositions commonly used to prepare mortars and concretes. BNS-based SP did not adsorb on sands, while PCE-based admixtures exhibited variable adsorption depending on different factors. The adsorption curves obtained revealed that the higher the sand fineness, the finer the particle size distribution and the higher the clay material, the greater was PCE admixture adsorption/ consumption. [Spanish] La elección de un superplastificante (SP) para el hormigón es un proceso complejo, ya que las propiedades del producto final se relacionan con la naturaleza del aditivo y su compatibilidad con los componentes del hormigón. Sin embargo hay pocos estudios sobre la compatibilidad entre los SPs y arenas utilizadas en morteros y hormigones. En la práctica se ha demostrado que la finura y la composición mineralógica de la arena afectan a la demanda de agua y al consumo de SPs. Las arcillas que pueden encontrarse en las arenas pueden también adsorber aditivos, reduciendo la cantidad disponible en solución para la adsorción por el cemento. Se han analizado las isotermas de adsorción para SPs de tipo PCE y BNS en cuatro arenas de diferente finura y composicion comúnmente utilizado para preparar morteros y hormigones. El aditivo BNS no se adsorbe en las arenas, mientras que los PCE

Bifurcation Analysis with Aerodynamic-Structure Uncertainties by the Nonintrusive PCE Method

Directory of Open Access Journals (Sweden)

Linpeng Wang

2017-01-01

Full Text Available An aeroelastic model for airfoil with a third-order stiffness in both pitch and plunge degree of freedom (DOF and the modified Leishman–Beddoes (LB model were built and validated. The nonintrusive polynomial chaos expansion (PCE based on tensor product is applied to quantify the uncertainty of aerodynamic and structure parameters on the aerodynamic force and aeroelastic behavior. The uncertain limit cycle oscillation (LCO and bifurcation are simulated in the time domain with the stochastic PCE method. Bifurcation diagrams with uncertainties were quantified. The Monte Carlo simulation (MCS is also applied for comparison. From the current work, it can be concluded that the nonintrusive polynomial chaos expansion can give an acceptable accuracy and have a much higher calculation efficiency than MCS. For aerodynamic model, uncertainties of aerodynamic parameters affect the aerodynamic force significantly at the stage from separation to stall at upstroke and at the stage from stall to reattach at return. For aeroelastic model, both uncertainties of aerodynamic parameters and structure parameters impact bifurcation position. Structure uncertainty of parameters is more sensitive for bifurcation. When the nonlinear stall flutter and bifurcation are concerned, more attention should be paid to the separation process of aerodynamics and parameters about pitch DOF in structure.

Technical note: New applications for on-line automated solid phase extraction

OpenAIRE

MacFarlane, John D.

1997-01-01

This technical note explains the disadvantages of manual solid phase extraction (SPE) techniques and the benefits to be gained with automatic systems. The note reports on a number of general and highly specific applications using the Sample Preparation Unit OSP-2A.

Topical anti-inflammatory activity of Polygonum cuspidatum extract in the TPA model of mouse ear inflammation

Directory of Open Access Journals (Sweden)

Wicker Louise

2008-02-01

Full Text Available Abstract Background This study tested the ability of a characterized extract of Polygonum cuspidatum (PCE to inhibit mouse ear inflammation in response to topical application of 12-O-tetradecanoylphorbol-13-acetate (TPA. Methods A 50% (wt:vol ethanolic solution of commercial 200:1 PCE was applied to both ears of female Swiss mice (n = 8 at 0.075, 0.15, 0.3, 1.25 and 2.5 mg/ear 30 min after TPA administration (2 μg/ear. For comparison, 3 other groups were treated with TPA and either 1 the vehicle (50% ethanol alone, 2 indomethacin (0.5 mg/ear, or 3 trans-resveratrol (0.62 mg/ear. Ear thickness was measured before TPA and at 4 and 24 h post-TPA administration to assess ear edema. Ear punch biopsies were collected at 24 h and weighed as a second index of edema. Myeloperoxidase activity was measured in each ear punch biopsy to assess neutrophil infiltration. Results PCE treatment at all doses significantly reduced ear edema compared to the TPA control. The PCE response was dose-dependent and 2.5 mg PCE significantly inhibited all markers of inflammation to a greater extent than indomethacin (0.5 mg. MPO activity was inhibited at PCE doses ≥ 1.25 mg/ear. Trans-resveratrol inhibited inflammation at comparable doses. Conclusion PCE inhibits development of edema and neutrophil infiltration in the TPA-treated mouse ear model of topical inflammation.

Crystallization and preliminary X-ray diffraction studies of the pneumococcal teichoic acid phosphorylcholine esterase Pce

Energy Technology Data Exchange (ETDEWEB)

Lagartera, Laura; González, Ana; Stelter, Meike; García, Pedro; Kahn, Richard; Menéndez, Margarita; Hermoso, Juan A., E-mail: xjuan@iqfr.csic.es

2005-02-01

The modular choline-binding protein Pce, the phosphorylcholine esterase from S. pneumoniae, has been crystallized by the hanging-drop vapour-diffusion method. A SAD data set from a derivative with a gadolinium complex has been collected to 2.7 Å resolution.

Effects of Direct-fed Microbial and Pine Cone Extract on Carcass Traits and Meat Quality of Hanwoo (Korean Native Cattle

Directory of Open Access Journals (Sweden)

Muhlisin

2016-05-01

Full Text Available The carcass traits and meat quality of Hanwoo (Korean native cattle whose diets were supplemented with direct-fed microbial (DFM and pine cone extract (PCE were evaluated. Twenty head of Hanwoo steers were divided equally into four groups and for a period of 6 months were given different diets: One group was fed a basal diet as control (CON, the other three groups were fed a basal diet supplemented with DFM-1%, DFM+PCE-1% and DFM+PEC-3%, respectively. DFM+PCE3% diet resulted the lowest carcass quality grade. The loins of DFM-1% contained higher moisture and lower fat than did the loins from the CON group. The crude protein content of DFM+PCE-3% group was significantly higher than that of the other groups. The water holding capacity and Warner-Bratzler shear force of the DFM+PCE-1% and 3% groups were lower than those of the CON and DFM-1% groups. The DFM-1% and 3% groups contained lower saturated fatty acid, higher unsaturated fatty acid, mono-unsaturated fatty acid, and poly-unsaturated fatty acid than did CON and DFM+PCE 1% group. Moreover, the n6:n3 ratios of DFM-1% and DFM+PCE-1% and 3% groups were slightly lower than that of the CON group. Thus we concluded that DFM and PCE supplementation resulted healthier Hanwoo beef with lower fat content and n6:n3 ratio.

A convenient method for the quantitative determination of elemental sulfur in coal by HPLC analysis of perchloroethylene extracts

Science.gov (United States)

Buchanan, D.H.; Coombs, K.J.; Murphy, P.M.; Chaven, C.

1993-01-01

A convenient method for the quantitative determination of elemental sulfur in coal is described. Elemental sulfur is extracted from the coal with hot perchloroethylene (PCE) (tetrachloroethene, C2Cl4) and quantitatively determined by HPLC analysis on a C18 reverse-phase column using UV detection. Calibration solutions were prepared from sublimed sulfur. Results of quantitative HPLC analyses agreed with those of a chemical/spectroscopic analysis. The HPLC method was found to be linear over the concentration range of 6 ?? 10-4 to 2 ?? 10-2 g/L. The lower detection limit was 4 ?? 10-4 g/L, which for a coal sample of 20 g is equivalent to 0.0006% by weight of coal. Since elemental sulfur is known to react slowly with hydrocarbons at the temperature of boiling PCE, standard solutions of sulfur in PCE were heated with coals from the Argonne Premium Coal Sample program. Pseudo-first-order uptake of sulfur by the coals was observed over several weeks of heating. For the Illinois No. 6 premium coal, the rate constant for sulfur uptake was 9.7 ?? 10-7 s-1, too small for retrograde reactions between solubilized sulfur and coal to cause a significant loss in elemental sulfur isolated during the analytical extraction. No elemental sulfur was produced when the following pure compounds were heated to reflux in PCE for up to 1 week: benzyl sulfide, octyl sulfide, thiane, thiophene, benzothiophene, dibenzothiophene, sulfuric acid, or ferrous sulfate. A sluury of mineral pyrite in PCE contained elemental sulfur which increased in concentration with heating time. ?? 1993 American Chemical Society.

Effect of sudden addition of PCE and bioreactor coupling to ZVI filters on performance of fluidized bed bioreactors operated in simultaneous electron acceptor modes.

Science.gov (United States)

Moreno-Medina, C U; Poggi-Varaldo, Hector M; Breton-Deval, L; Rinderknecht-Seijas, N

2017-11-01

The present work evaluated the effects of (i) feeding a water contaminated with 80 mg/L PCE to bioreactors seeded with inoculum not acclimated to PCE, (ii) coupling ZVI side filters to bioreactors, and (iii) working in different biological regimes, i.e., simultaneous methanogenic aeration and simultaneous methanogenic-denitrifying regimes, on fluidized bed bioreactor performance. Simultaneous electron acceptors refer to the simultaneous presence of two compounds operating as final electron acceptors in the biological respiratory chain (e.g., use of either O 2 or NO 3 - in combination with a methanogenic environment) in a bioreactor or environmental niche. Four lab-scale, mesophilic, fluidized bed bioreactors (bioreactors) were implemented. Two bioreactors were operated as simultaneous methanogenic-denitrifying (MD) units, whereas the other two were operated in partially aerated methanogenic (PAM) mode. In the first period, all bioreactors received a wastewater with 1 g chemical oxygen demand of methanol per liter (COD-methanol/L). In a second period, all the bioreactors received the wastewater plus 80 mg perchloroethylene (PCE)/L; at the start of period 2, one MD and one PAM were coupled to side sand-zero valent iron filters (ZVI). All bioreactors were inoculated with a microbial consortium not acclimated to PCE. In this work, the performance of the full period 1 and the first 60 days of period 2 is reported and discussed. The COD removal efficiency and the nitrate removal efficiency of the bioreactors essentially did not change between period 1 and period 2, i.e., upon PCE addition. On the contrary, specific methanogenic activity in PAM bioreactors (both with and without coupled ZVI filter) significantly decreased. This was consistent with a sharp fall of methane productivity in those bioreactors in period 2. During period 2, PCE removals in the range 86 to 97 % were generally observed; the highest removal corresponded to PAM bioreactors along with the

Origanum vulgare leaf extract protects mice bone marrow cells against ionizing radiation

Directory of Open Access Journals (Sweden)

Reza Ghasemnezhad Targhi

2016-11-01

Full Text Available Objective: Ionizing radiation produces free radicals which induce DNA damage and cell death. Origanum vulgare leaf extract (OVLE is a natural compound and its capability of scavenging free radicals and its antioxidant activity have been demonstrated by many researchers. In this study, using micronucleus assay, radioprotective effect of OVLE against clastogenic and cytotoxic effect of gamma irradiation has been investigated in mice bone marrow cells. Materials and Methods: OVLE was injected intraperitoneally to the BALB/c mice 1hr prior to gamma irradiation (3Gy at the doses of 100 and 200 mg/kg. Twenty four hours after irradiation or treatment, animals were killed and smears were prepared from the bone marrow cells. The slides were stained with May Grunwald–Giemsa method and analyzed microscopically. The frequency of micronucleated polychromatic erythrocytes (MnPCEs, micronucleated normochromatic erythrocyte (MnNCEs and cell proliferation ratio PCE/PCE+NCE (polychromatic erythrocyte/polychromatic erythrocyte + normochromatic erythrocyte were calculated. Results: The results showed that gamma irradiation (3Gy increased the frequency of MnPCEs, MnNCEs and  reduced the PCE/PCE+NCE ratio in mice bone marrow compared to the non-irradiated control group (p< 0.0001. Injection of OVLE significantly reduced the frequency of MnPCEs (p< 0.0001 and MnNCEs (p< 0.05 and increased the PCE/PCE+NCE ratio as compared to the irradiated control group (p< 0.05. Conclusion: It seems that OVLE with its antioxidant properties and its capability of scavenging free radicals and reactive oxygen species can reduce the cytotoxic effects of gamma irradiation in mice bone marrow cells.

La delegación del PCE en México (1939-1956 : origen y límite de una voluntad de liderazgo de la oposición

Directory of Open Access Journals (Sweden)

Pablo Jesús Carrión Sánchez

2004-01-01

Full Text Available A través del estudio de la Delegación del PCE en México se analizan algunas claves esenciales del exilio político de 1939. En paralelo a la primera fase de la Dictadura los desterrados tratan de estructurar plataformas de oposición para derribarla. En ellas se observa la voluntad de liderazgo del PCE en contraste con su relativo aislamiento tanto del resto del exilio como de la propia política mexicana.Through the study of the Delegation of the PCE in México some essential keys of the political exile of 1939 are analysed. In paral leí to the firstphase ofthe Dictatorship the exiles try to structure platforms of opposition to demolish it. In them the will of leadership of the PCE is observed in contrast with its relative isolation of the rest of the exile like of the own Mexican politics.

Alteration of Depressive-like Behaviors by Psilocybe cubensis Alkaloid Extract in Mice: the Role of Glutamate Pathway

Directory of Open Access Journals (Sweden)

Elaheh Mahmoudi

2018-03-01

Full Text Available Background and objectives: Considering the increasing prevalence of depression, many studies are launched to investigate new antidepressant treatments. The present research has shown how psilocybin as an active compound of Psilocybe cubensis (Earle Singer extract (PCE can change the parameters related to depression and anxiety in animal models. Both serotonin (5-hydroxytryptamine: 5-HT and glutamate modulate depressive-like behaviors and, therefore, we examined the possible interaction of psilocybin as 5-HT1 agonist with glutamate receptor N-methyl-D-aspartate (NMDA. Methods: Psilocybe cubensis extract of this mushroom was prepared by ethyl acetate. NMRI mice involved in all experiments and were treated with the vehicle, extract, or standard drug intraperitoneally. Open field (OFT, forced swimming (FST and tail suspension tests (TST were applied to measure the intended parameters. OFT was performed to verify the applied doses for measuring the following antidepressant activity.  Results: PCE at the doses of 100 mg/kg significantly changed the locomotion, time spent in center and velocity of the animals in OFT. While treatment of the animals with PCE 10 and 40 mg/kg or ketamine 1 mg/kg did not alter the locomotor activity, co-administration of these subeffective amounts significantly reduced the immobility time in both FST and TST. Conclusion: These effects may indicate possible implication of psilocybin with NMDA receptor which consequently produces the antidepressant effects.

Analysis of Selected Enhancements for Soil Vapor Extraction

Science.gov (United States)

1997-09-01

1995 NR VOC 12 NM NMb b Berlin Harress 1989 Sand, silty lenses c-1,2-DCE, TCE, 24 c-1,2-DCE: >2 c-1,2-DCE: >0.440 Aquitard-clay PCE Bielefeld...Nordrhein Harress 1989 Fill, sand, silt PCE, TCE, TCA 11 PCE: 27; TCE: 4.3; TCA: 0.7 Total VOCs: 1.207 -Westfalen Aquitard-siltstone Munich, Bavaria... Harress 1989 Fill, gravel, sand PCE, TCE, TCA 4 PCE: 2.2; TCE: 0.4; TCA: PCE: 0.539; TCE: 0.012; Aquitard-clayey silt 0.15 TCA: 0.002 Nordrhein

Technical progress review of extraction of uranium from fly ash

International Nuclear Information System (INIS)

Gao Renxi; Gao Junning; Wu Qingming; Chen Gang; Wan Hongjin; Zhang Ziyue

2014-01-01

The increasing of fly ash in coal-fired power plants at home and abroad year by year and the potential impacts to the environment attracted media attention. Although the extraction of uranium from the fly ash in coal-fired power plants had optional process from technique aspect and sufficient preliminary researches, but considering the low grade of the uranium in fly ash and particularity of the mineral composition, it is easy to have a high cost of extraction. As a consequence, it is not included in the development plan of uranium mining and metallurgy. The present applications of fly ash are only building materials, building roads and pit valley backfill, the resource utilization rate was low and was still in its early stages of development and application. In view of this, the research advances and the latest development trends of extraction of uranium from fly ash at home and abroad were introduced from the technical aspect, and the beneficial analyzes of the prospect and advices to this industry were given. (authors)

Proof-of-Concept Study: Novel Microbially-Driven Fenton Reaction for In Situ Remediation of Groundwater Contaminated with 1,4-Dioxane, Tetrachloroethene (PCE) and Trichloroethene (TCE)

Science.gov (United States)

2014-09-17

with 1,4-Dioxane, Tetrachloroethene (PCE) and Trichloroethene ( TCE ) SERDP Project ER-2305 September 2014 Thomas DiChristina Georgia...HO) radicals that degrade 1,4- dioxane, TCE , and PCE. In comparison to conventional (purely abiotic) Fenton reactions, the microbially-driven Fenton...reaction operates at circumneutral pH and does not require addition of exogenous H2O2 or UV irradiation to regenerate Fe(II). The 1,4-dioxane, TCE

Radio protective effect of black mulberry extract on radiation-induced damage in bone marrow cells and liver in the rat

Science.gov (United States)

Ghasemnezhad Targhi, Reza; Homayoun, Mansour; Mansouri, Somaieh; Soukhtanloo, Mohammad; Soleymanifard, Shokouhozaman; Seghatoleslam, Masoumeh

2017-01-01

Ionizing radiation by producing free radicals induces tissue oxidative stress and has clastogenic and cytotoxic effects. The radio protective effect of black mulberry extract (BME) has been investigated on liver tissue and bone marrow cells in the rat. Intraperitoneal (ip) administration of 200 mg/kg BME three days before and three days after 3 Gy and 6 Gy gamma irradiation significantly reduced the frequencies of micro nucleated polychromatic erythrocytes (MnPCEs) and micro nucleated norm chromatic erythrocyte (MnNCEs) and increased PCE/PCE+NCE ratio in rat bone marrow compared to the non-treated irradiated groups. Moreover, this concentration of BME extract decreased the level of malondialdehyde (MDA) and superoxide dismutase (SOD), as well as enhanced the total thiol content and catalase activity in rat's liver compared to the non-treated irradiated groups. It seems that BME extract with antioxidant activity reduced the genotoxicity and cytotoxicity induced by gamma irradiation in bone marrow cells and liver in the rat.

Efficient Perovskite Solar Cells over a Broad Temperature Window : The Role of the Charge Carrier Extraction

NARCIS (Netherlands)

Shao, Shuyan; Liu, Jian; Fang, Hong-Hua; Qiu, Li; ten Brink, Gert H.; Hummelen, Jan C.; Koster, L. Jan Anton; Loi, Maria Antonietta

2017-01-01

The mechanism behind the temperature dependence of the device performance in hybrid perovskite solar cells (HPSCs) is investigated systematically. The power conversion efficiency (PCE) of the reference cell using [60] PCBM as electron extraction layer (EEL) drops significantly from 11.9% at 295 K to

Improved Understanding of In Situ Chemical Oxidation. Technical Objective I: Contaminant Oxidation Kinetics Contaminant Oxidation Kinetics

Science.gov (United States)

2009-05-01

methyl tert butyl ether NAPL non-aqueous phase liquid NOD natural oxidant demand •OH hydroxide radical Ox oxidant O3 ozone PCE...and persulfate; and Technical Objective 2, assess how soil properties (e.g., soil mineralogy , natural carbon content) affect oxidant mobility and...to develop a general description of kobs vs. T because there are many reactions that can contribute to the concentration of the reactive intermediate

La reorganización y la oposición del PCE al franquismo, (1939-1946)

OpenAIRE

Fernández Rodríguez, Carlos

2016-01-01

En el proceso y desarrollo histórico del PCE durante el primer franquismo tuvieron lugar diferentes reestructuraciones y luchas clandestinas protagonizadas por miles de militantes que integraron la organización comunista en aquellos años, muchos de ellos fueron encarcelados y algunos ejecutados por las autoridades franquistas. El origen de la resistencia antifranquista tuvo lugar incluso antes de la finalización de la guerra civil española y estuvo marcada por la desunión entre las distintas ...

Radio-immunoassay of antidiuretic hormone. Choice of a technic of extraction. Normal and pathological values

International Nuclear Information System (INIS)

Basuyau, J.P.; Brunelle, P.; Le Bihan, G.; Bourreille, J.; Bohuon, C.

1980-01-01

The low serum concentration of ADH requires extraction prior to assay. Various methods are compared (direct extraction by acetone, adsorption on talcum powder, Florisil, silicilic acid, Fuller's earth. QUSO, carbon-dextran, adsormone, then elution with hydrochloric acetone). The technic finally used was extraction with Florisil. The antibody used was commercially accessible. The separation of bound from free hormone required a second antibody fixed on Sephadex (DASP). The usual values found in 31 normal subjects from 22 to 89 years were: 7.4 . 4.1 pmol/l(M 2 tau) 1 pmol/l = 1.08 pg/ml. These assays were carried out on tissue extracts prepared by mashing tumour fragments or lymph nodes removed from a patient with the Schwartz Bartter syndrome. They showed the existence in these tissues of high concentrations of ADH immunologically identical with that present in the serum of normal subjects [fr

Adding a purple corn extract in rats supplemented with chia oil decreases gene expression of SREBP-1c and retains Δ5 and Δ6 hepatic desaturase activity, unmodified the hepatic lipid profile.

Science.gov (United States)

Reyna Gallegos, Sixto; Torres Arrunátegui, Génesis; Valenzuela, Rodrigo; Rincón-Cervera, Miguel Ángel; Villanueva Espinoza, María Elena

2018-05-01

Flavonoids upregulate gene expression of PPAR-α and underregulate the gene expression of SREBP-1c, and their intake increases the plasmatic concentration of n-3 LC-PUFAs. However, the biological mechanisms underlying these effects have not been elucidated. In this work, the effect of oral supplementation of ALA from chia (Salvia hispanica L.) seed oil and anthocyanins from a purple corn extract (PCE) on gene expression of SREBP-1c, PPAR-α and Δ5 and Δ6 desaturases (Δ5D and Δ6D), the activity of these enzymes in the liver as well as the hepatic lipid profile were evaluated in thirty-six female Sprague Dawley rats whose diet was supplemented with olive oil (OL), chia oil (CH), olive oil and PCE (OL + PCE) or chia oil and PCE (CH + PCE). Gene expression of PPAR-α was significantly higher when supplemented with CH and CH + PCE, SREBP-1c gene expression was higher when supplemented with chia oil. CH supplementation enhanced Δ5D expression whereas no significant differences between treatments were observed concerning Δ6D gene expression. Activities of both desaturases were increased by including olive oil (OL + PCE and OL), and they were found to be higher in CH + PCE respect to CH for both enzymes. The ALA and n-3 LCPUFAs hepatic content was higher with CH, decreasing the levels of AA and n-6 LCPUFAs. It is concluded that the joint action of flavonoids such as anthocyanins and ALA show an anti-adipogenic effect. Desaturase activity was inhibited by ALA and kept by the anthocyanins from PCE, thus anthocyanins would exert a protective effect on the desaturase activity but they would not affect on its gene expression, however, high doses of ALA increased the production of its metabolites, masking the effect of PCE. Copyright © 2018 Elsevier Ltd. All rights reserved.

Evaluation of the genotoxic and cytotoxic effects of crude extracts of Cordia ecalyculata and Echinodorus grandiflorus.

Science.gov (United States)

da Silva, Cristiano José; Bastos, Jairo Kenupp; Takahashi, Catarina Satie

2010-02-03

Cordia ecalyculata Vell. and Echinodorus grandiflorus (Cham. & Schltdl.) Micheli are extensively used in Brazil as therapeutic preparations for indigenous groups and the general population. These plants have been used in the folk medicine as: tonic, diuretic, anti-inflammatory, appetite suppressants, for the treatment of snake bites, and weight loss. In this study, it was verified the possible cytotoxic and genotoxic effects of the crude extracts of. Cordia ecalyculata and Echinodorus grandiflorus, as well as their effectiveness in treating obesity. The Micronucleus Test was used for the evaluation of possible clastogenic and aneugenic effects, and the Comet Assay was used for the evaluation of single-strand and double-strand DNA breaks. The cytotoxic effects of the crude extracts were verified by PCE/NCE ratio. Swiss mice (Mus musculus) were used as the experimental model. It was observed a significant (PCordia ecalyculata or Echinodorus grandiflorus extracts, in comparison with the negative control. There were no significant differences (P>0.05) in the frequency of micronucleated polychromatic erythrocytes for both extract treatment. We observed that treatment with the Cordia ecalyculata extract at concentrations of 1000 and 2000 mg/kg bw resulted in a PCE/NCE ratio that was larger (P0.05). The results of this study allowed us to infer that the crude extracts of Cordia ecalyculata and Echinodorus grandiflorus do not display cytotoxic or genotoxic activities. However, they do possess weak clastogenic activity (without significance) on peripheral blood cells. Contrary to commonly held beliefs it was also found in this study that the extracts are not effective for obesity treatments. Copyright 2009 Elsevier Ireland Ltd. All rights reserved.

Six-phase soil heating accelerates VOC extraction from clay soil

International Nuclear Information System (INIS)

Gauglitz, P.A.; Roberts, J.S.; Bergsman, T.M.; Caley, S.M.; Heath, W.O.; Miller, M.C.; Moss, R.W.; Schalla, R.; Jarosch, T.R.; Eddy-Dilek, C.A.

1994-08-01

Six-Phase Soil Heating (SPSH) was demonstrated as a viable technology for heating low permeability soils containing volatile organic contaminants. Testing was performed as part of the Volatile Organic Compounds in Non-Arid Soils Integrated Demonstration (VOC Non-Arid ID) at the Savannah River Site. The soil at the integrated demonstration site is contaminated with perchloroethylene (PCE) and trichloroethylene (TCE); the highest soil contamination occurs in clay-rich zones that are ineffectively treated by conventional soil vapor extraction due to the very low permeability of the clay. The SPSH demonstration sought to heat the clay zone and enhance the performance of conventional soil vapor extraction. Thermocouples at thirty locations quantified the areal and vertical heating within the treated zone. Soil samples were collected before and after heating to quantify the efficacy of heat-enhanced vapor extraction of PCE and TCE from the clay soil. Samples were taken (essentially every foot) from six wells prior to heating and adjacent to these wells after heating. Results show that contaminant removal from the clay zone was 99.7% (median) within the electrode array. Outside the array where the soil was heated, but to only 50 degrees C, the removal efficiency was 93%, showing that heating accelerated the removal of VOCs from the clay soil. The accelerated remediation resulted from effective heating of the contaminated clay zone by SPSH. The temperature of the clay zone increased to 100 degrees C after 8 days of heating and was maintained near 100 degrees C for 17 days. Electrical heating removed 19,000 gal of water from the soil as steam, with peak removal rate of 1,500 gpd of condensed steam

Technical and economic study of a mobile system for extraction of eucalyptus essential oil

Directory of Open Access Journals (Sweden)

Gisele Aparecida Vivan

2011-03-01

Full Text Available The production of essential oils has become increasing in Brazil, especially considering the benefits that certain substances can add to health and range of cosmetics, toiletries and drugs that originate in its processing. Based on these conditions and in the vast area of the Rio Grande do Sul where it is being implanted the culture of eucalyptus, this study seeks ways to boost the economic structure of culture, seeking to generate new business opportunities through the extraction of oil contained in the leaves Eucalyptus, a byproduct of the paper industry, the current main economic interest of culture. Based on these assumptions, it was elaborated a conceptual design of a mobile equipment able to meet the processing demand of the crop, determining a diagram processing flow and fitting the equipment to meet this demand. Subsequently, it was evaluated the technical and economic feasibility of deploying the mobile extraction system for essential oil of eucalyptus in the southern region of Rio Grande do Sul, conducting technical studies for the improvement and efficiency of the conceptual design and economic feasibility analysis to determine variables that determine the success of the project. It was conclude that the conceptual design has beneficial aspects, especially regarding the mobility, flexibility of use, minimization of empty spaces and water use in semi-closed circuit. In the analysis of economic feasibility, the simulated scenarios showed positive values for Net Present Value, Internal Rate of Return above the minimum rate of attractiveness and capital Payback relatively short, even for the scenarios considered critical.

Modification and aging precipitation behavior of hypereutectic Al-21wt.%Si alloy treated by P+Ce combination

Directory of Open Access Journals (Sweden)

Liu Pei

2014-11-01

Full Text Available In the present study, the tested hypereutectic Al-21wt.%Si alloys were prepared by modifying the melt using different proportions of P and Ce, and then applying T6 heat treatment. The modification effects and mechanism of P+Ce complex modifier on the Si phase of hypereutectic Al-21wt.%Si alloy were studied, and the aging precipitation behavior after modification was characterized by means of tensile strength measurement, OM, SEM and TEM analysis. The results show that the massive primary silicon phase particles are significantly refined after modification, while the needle-like eutectic silicon crystals become fibrous and short. It was found that the mechanism of phosphorus modification on the primary silicon can be attributed to heterogeneous nucleation of AlP, while the modification mechanism of Ce can be explained by adsorbing-twinning theory. In the aged microstructure of the modified hypereutectic Al-21wt.%Si alloy, there existed some strengthening phases such as Al4Cu9, Al2Cu, AlCu3, and Al57Mn12. The P+Ce complex modifier not only affected the size of primary silicon and eutectic silicon, but also the aging behavior of alloys under the heat treatment process. When Al-21wt.%Si alloy was modified using 0.08%wt.P + 0.6wt.% Ce, the aging precipitates were dispersed uniformly in the alloy, and its mechanical properties at room and elevated temperatures are optimized (Rm = 287.6 MPa at RT, Rm = 210 MPa at 300 ℃.

Niépce-Bell or Turing: how to test odour reproduction.

Science.gov (United States)

Harel, David

2016-12-01

Decades before the existence of anything resembling an artificial intelligence system, Alan Turing raised the question of how to test whether machines can think, or, in modern terminology, whether a computer claimed to exhibit intelligence indeed does so. This paper raises the analogous issue for olfaction: how to test the validity of a system claimed to reproduce arbitrary odours artificially, in a way recognizable to humans. Although odour reproduction systems are still far from being viable, the question of how to test candidates thereof is claimed to be interesting and non-trivial, and a novel method is proposed. Despite the similarity between the two questions and their surfacing long before the tested systems exist, the present question cannot be answered adequately by a Turing-like method. Instead, our test is very different: it is conditional, requiring from the artificial no more than is required from the original, and it employs a novel method of immersion that takes advantage of the availability of easily recognizable reproduction methods for sight and sound, a la Nicéphore Niépce and Alexander Graham Bell. © 2016 The Authors.

Antioxidant Evaluation of Methanolic Extract of Black Nightshades Ripe Fruits against Technical and Formulated Parathion-Induced Damage in Albino Rats

International Nuclear Information System (INIS)

Abdel-Rahiml, E.A.; Abdel-Rahim, G.A.; Atia, A.I.

2009-01-01

Parathion in technical or formulated form at a sub-lethal dose of 1/20 LD 50 was applied orally or dermally at 2-day interval for three months to determine its effect on RNA, DNA and protein content as well as RNA ase and DNA ase activity in different organs liver, brain and kidneys of adult male albino rats. Also, serum GOT, GPT and ALP activity as well as serum total soluble protein, albumin, globulin, bilirubin and uric acid content were determined in adult male albino rats (Rattus norvegicus). In addition, the present studies were undertaken to investigate different biological activities of the above parameters of black nightshades (Solanum nigrum L) methanolic extract. Two kinds of experimental works were taken off (antioxidants and protective). The results showed that technical and formulated parathion increased RNA and protein content but the content of DNA was insignificantly decreased in all rat organs tissue (liver, brain and kidneys) relative to control. The activity of RNA ase was also stimulated. In case of liver and kidney functions the present data observed that serum GOT, GPT and ALP activity was stimulated but total soluble protein, albumin and globulin content was decreased but the urea, uric acid and bilirubin content of serum was increased. Also, liver lipid peroxidation was elevated significantly either by technical or formulated parathion (ingested orally or induced dermally). It should be noted that formulated parathion ingested orally was the most effective, but the technical one had the lowest toxicity. The results of the present studies showed that crude methanolic extract of black nightshades ripe fruits has a strong antioxidant activity as showed by DPPH, nitric oxide scavenging, total reducing power, Fenton's reaction and total antioxidant capacity assay. Finally the the methanolic extract of the present medicinal plant observed a valuable influence as a protective agent in vivo in serum, liver, brain and kidneys damage of parathion

Vacuum extraction

DEFF Research Database (Denmark)

Maagaard, Mathilde; Oestergaard, Jeanett; Johansen, Marianne

2012-01-01

Objectives. To develop and validate an Objective Structured Assessment of Technical Skills (OSATS) scale for vacuum extraction. Design. Two-part study design: Primarily, development of a procedure-specific checklist for vacuum extraction. Hereafter, validation of the developed OSATS scale for vac...

Ocean Thermal Extractable Energy Visualization- Final Technical Report on Award DE-EE0002664. October 28, 2012

Energy Technology Data Exchange (ETDEWEB)

Ascari, Matthew B.; Hanson, Howard P.; Rauchenstein, Lynn; Van Zwieten, James; Bharathan, Desikan; Heimiller, Donna; Langle, Nicholas; Scott, George N.; Potemra, James; Nagurny, N. John; Jansen, Eugene

2012-10-28

The Ocean Thermal Extractable Energy Visualization (OTEEV) project focuses on assessing the Maximum Practicably Extractable Energy (MPEE) from the world's ocean thermal resources. MPEE is defined as being sustainable and technically feasible, given today's state-of-the-art ocean energy technology. Under this project the OTEEV team developed a comprehensive Geospatial Information System (GIS) dataset and software tool, and used the tool to provide a meaningful assessment of MPEE from the global and domestic U.S. ocean thermal resources. The OTEEV project leverages existing NREL renewable energy GIS technologies and integrates extractable energy estimated from quality-controlled data and projected optimal achievable energy conversion rates. Input data are synthesized from a broad range of existing in-situ measurements and ground-truthed numerical models with temporal and spatial resolutions sufficient to reflect the local resource. Energy production rates are calculated for regions based on conversion rates estimated for current technology, local energy density of the resource, and sustainable resource extraction. Plant spacing and maximum production rates are then estimated based on a default plant size and transmission mechanisms. The resulting data are organized, displayed, and accessed using a multi-layered GIS mapping tool, http://maps.nrel.gov/mhk_atlas with a user-friendly graphical user interface.

Analysis of vapor extraction data from applications in Europe

International Nuclear Information System (INIS)

Hiller, D.; Gudemann, H.

1989-01-01

This paper discusses vapor extraction, an in-situ process to remove volatile organic compounds (VOC) from soils of the vadose zone, applied in Europe since the early 1980s. In a vapor extraction well a negative differential pressure is created by a blower or similar device. The differential pressure generates a steady flow of soil gas towards the extraction well and thus provides a flushing of the soil with air undersaturated in respect to the contaminant concentration. Contaminants will evaporate into the gaseous phase both form the liquid phase and form the soil. Differential pressures applied range from 15 inches - 350 inches of water. The contaminated discharge air can be treated by activated carbon or other suitable methods. The effective radius of vapor extraction systems (VES) ranges typically form 20 feet to 150 feet underneath non-sealed - and up to 300 feet underneath sealed surfaces. Contamination from volatile organic compounds (VOC) have turned out to be widespread due to their almost ubiquitous presence in industrial processes. Specifically, VOC include halogenated hydrocarbons like TCE, PCE or TCA, aromatic hydrocarbons like benzene, toluene, xylene and volatile fuels like gasoline

Graded Heterojunction Engineering for Hole-Conductor-Free Perovskite Solar Cells with High Hole Extraction Efficiency and Conductivity.

Science.gov (United States)

Li, Bo; Zhang, Yanan; Zhang, Luyuan; Yin, Longwei

2017-10-01

Despite great progress in the photovoltaic conversion efficiency (PCE) of inorganic-organic hybrid perovskite solar cells (PSCs), the large-scale application of PSCs still faces serious challenges due to the poor-stability and high-cost of the spiro-OMeTAD hole transport layer (HTL). It is of great fundamental importance to rationally address the issues of hole extraction and transfer arising from HTL-free PSCs. Herein, a brand-new PSC architecture is designed by introducing multigraded-heterojunction (GHJ) inorganic perovskite CsPbBr x I 3- x layers as an efficient HTL. The grade adjustment can be achieved by precisely tuning the halide proportion and distribution in the CsPbBr x I 3- x film to reach an optimal energy alignment of the valance and conduction band between MAPbI 3 and CsPbBr x I 3- x . The CsPbBr x I 3- x GHJ as an efficient HTL can induce an electric field where a valance/conduction band edge is leveraged to bend at the heterojunction interface, boosting the interfacial electron-hole splitting and photoelectron extraction. The GHJ architecture enhances the hole extraction and conduction efficiency from the MAPbI 3 to the counter electrode, decreases the recombination loss during the hole transfer, and benefits in increasing the open-circuit voltage. The optimized HTL-free PCS based on the GHJ architecture demonstrates an outstanding thermal stability and a significantly improved PCE of 11.33%, nearly 40% increase compared with 8.16% for pure HTL-free devices. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Technical and Economic Assessment of Solar Photovoltaic for Groundwater Extraction on the Hanford Site

Energy Technology Data Exchange (ETDEWEB)

Mackley, Rob D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Anderson, David M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Thomle, Jonathan N. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Strickland, Christopher E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-09-01

The overall goal of environmental remediation is to protect human health and the environment. Implementing renewable energy sources such as solar photovoltaic (PV) in groundwater extraction and pump-and-treat (P&T) systems may help minimize the environmental footprint of remediation efforts. The first step in considering solar PV for powering Hanford groundwater extraction is assessing the technical and economic feasibility and identifying potential target locations where implementation would be most successful. Accordingly, a techno-economic assessment of solar PV for Hanford groundwater extraction was completed in FY15. Multiple solar PV alternatives ranging in size from 1.2 to 22.4 kWp DC were evaluated and compared against traditional grid-powered systems. Results indicate that the degree to which solar PV alternatives are feasible is primarily a function of the distance of avoided power cable costs and the inclusion of an energy storage component. Standalone solar PV systems provide an energy source at the well and avoid the costs and logistics associated with running long lengths of expensive power cable to the well-head. When solar PV systems include a battery storage component, groundwater can be pumped continuously day and night in a year-round schedule. However, due to the high cost premium of the energy storage component, a fully solar-powered solution could not provide an economic direct replacement for line-powered pumping systems. As a result, the most ideal target locations for successful implementation of solar PV on the Hanford Site are remote or distant extraction wells where the primary remedial objective is contaminant mass removal (as opposed to hydraulic containment) and three-season (March through October) intermittent pumping is acceptable (e.g. remediation of hexavalent chromium in 200-UP-1).

Evaluation of Mango Byproduct Extracts as Antioxidant Against Pb-Acetate-Induced Oxidative Stress and Genotoxicity in Mice

Directory of Open Access Journals (Sweden)

Makawy Aida I. El

2015-03-01

Full Text Available The antioxidant and antiproliferative properties of mango by-products were investigated. This study was carried out to evaluate the protective role of mango peel or kernel defatted extracts against Pb-acetate adverse effects on oxidant/antioxidant status, liver dysfunction biomarkers, histopathological changes and genotoxicity in male mice. Total phenolic content and antioxidant activity of both extracts were evaluated. Two doses of both extracts (50 and 100 mg/kg were used to evaluate their role against the toxicity of Pb-acetate (500 ppm. Mice given mango extracts with Pb-acetate had significantly lower plasma MDA, AST and ALT and higher glutathione than mice given Pb-acetate alone. Mango extracts prevented the histopathological changes in liver induced by Pb-acetate and decreased the cytotoxicity of lead by increasing the ratio of PCE/NCE. Mango extract treatment reduced the DNA damage induced by Pb-acetate in liver as demonstrated by a reduction in micronuclei and decrease in tail length, tail DNA% and Olive tail moment. It can be concluded that mango by-product extracts have potential to protect from oxidative stress and genotoxicity of lead.

Time series geophysical monitoring of permanganate injections and in situ chemical oxidation of PCE, OU1 area, Savage Superfund Site, Milford, NH, USA

Science.gov (United States)

Harte, Philip T.; Smith, Thor E.; Williams, John H.; Degnan, James R.

2012-01-01

In situ chemical oxidation (ISCO) treatment with sodium permanganate, an electrically conductive oxidant, provides a strong electrical signal for tracking of injectate transport using time series geophysical surveys including direct current (DC) resistivity and electromagnetic (EM) methods. Effective remediation is dependent upon placing the oxidant in close contact with the contaminated aquifer. Therefore, monitoring tools that provide enhanced tracking capability of the injectate offer considerable benefit to guide subsequent ISCO injections. Time-series geophysical surveys were performed at a superfund site in New Hampshire, USA over a one-year period to identify temporal changes in the bulk electrical conductivity of a tetrachloroethylene (PCE; also called tetrachloroethene) contaminated, glacially deposited aquifer due to the injection of sodium permanganate. The ISCO treatment involved a series of pulse injections of sodium permanganate from multiple injection wells within a contained area of the aquifer. After the initial injection, the permanganate was allowed to disperse under ambient groundwater velocities. Time series geophysical surveys identified the downward sinking and pooling of the sodium permanganate atop of the underlying till or bedrock surface caused by density-driven flow, and the limited horizontal spread of the sodium permanganate in the shallow parts of the aquifer during this injection period. When coupled with conventional monitoring, the surveys allowed for an assessment of ISCO treatment effectiveness in targeting the PCE plume and helped target areas for subsequent treatment.

In vivo evaluation of anticlastogenicity of extracts from medicinal plants of Miconia genus using the micronucleus test Avaliação in vivo da anticlastogenicidade de extratos de plantas medicinais do gênero Miconia através do teste do micronúcleo

Directory of Open Access Journals (Sweden)

Ilce Mara S. Cólus

2008-10-01

Full Text Available The genus Miconia is comprised of approximately 1000 species. For some of them, biological activities have already been described such as the analgesic and the anti-microbial ones. The purpose of this work was to evaluate the possible protective and cytotoxic effects of the methanolic extract from M. albicans, M. cabucu, M. rubiginosa and M. stenostachya and the chloroformic extract from M. albicans in mice bone marrow cells in 540 mg/kg p.c. dose. The extracts were administered by means of forced feeding and the cyclophosphamide (CPA was applied intraperitonially one hour after supplementation with extracts. All animals were submitted to euthanasia 30 hours after the treatment. The analyzed cells were extracted from mice bone marrow according to protocol described by Schmid (1975. The cytotoxicity of the extracts was evaluated through the percentage of polychromatic erythrocytes (PCE in 200 erythrocytes (PCE + NCE. Two thousand PCEs of each animal were analyzed and the micronucleated polychromatic erythrocytes (MNPCEs frequencies were scored. The results obtained indicated that none of the extracts associated with the CPA showed cytotoxic effect and only the extracts of M. rubiginosa and M. stenostachya showed protective effect to DNA. Chemical analyses of the extracts showed that the four species studied contain mainly flavonoids, phenolic compounds and tannins. The phytochemical characterization of these extracts could contribute to elucidate the protective effect presented only by the species M. rubiginosa and M. stenostachya, besides making it possible the study of other therapeutic activities. O gênero Miconia possui aproximadamente 1000 espécies, e para algumas, já foram descritas atividades biológicas como a analgésica e antimicrobiana. Esse trabalho teve como objetivo avaliar os possíveis efeitos protetores e citotóxicos dos extratos metanólicos de M. albicans, M. cabucu, M. rubiginosa e M. stenostachya e do extrato clorof

Time series geophysical monitoring of permanganate injections and in situ chemical oxidation of PCE, OU1 area, Savage Superfund Site, Milford, NH, USA.

Science.gov (United States)

Harte, Philip T; Smith, Thor E; Williams, John H; Degnan, James R

2012-05-01

In situ chemical oxidation (ISCO) treatment with sodium permanganate, an electrically conductive oxidant, provides a strong electrical signal for tracking of injectate transport using time series geophysical surveys including direct current (DC) resistivity and electromagnetic (EM) methods. Effective remediation is dependent upon placing the oxidant in close contact with the contaminated aquifer. Therefore, monitoring tools that provide enhanced tracking capability of the injectate offer considerable benefit to guide subsequent ISCO injections. Time-series geophysical surveys were performed at a superfund site in New Hampshire, USA over a one-year period to identify temporal changes in the bulk electrical conductivity of a tetrachloroethylene (PCE; also called tetrachloroethene) contaminated, glacially deposited aquifer due to the injection of sodium permanganate. The ISCO treatment involved a series of pulse injections of sodium permanganate from multiple injection wells within a contained area of the aquifer. After the initial injection, the permanganate was allowed to disperse under ambient groundwater velocities. Time series geophysical surveys identified the downward sinking and pooling of the sodium permanganate atop of the underlying till or bedrock surface caused by density-driven flow, and the limited horizontal spread of the sodium permanganate in the shallow parts of the aquifer during this injection period. When coupled with conventional monitoring, the surveys allowed for an assessment of ISCO treatment effectiveness in targeting the PCE plume and helped target areas for subsequent treatment. Published by Elsevier B.V.

Microbially enhanced dissolution and reductive dechlorination of PCE by a mixed culture: Model validation and sensitivity analysis

Science.gov (United States)

Chen, Mingjie; Abriola, Linda M.; Amos, Benjamin K.; Suchomel, Eric J.; Pennell, Kurt D.; Löffler, Frank E.; Christ, John A.

2013-08-01

Reductive dechlorination catalyzed by organohalide-respiring bacteria is often considered for remediation of non-aqueous phase liquid (NAPL) source zones due to cost savings, ease of implementation, regulatory acceptance, and sustainability. Despite knowledge of the key dechlorinators, an understanding of the processes and factors that control NAPL dissolution rates and detoxification (i.e., ethene formation) is lacking. A recent column study demonstrated a 5-fold cumulative enhancement in tetrachloroethene (PCE) dissolution and ethene formation (Amos et al., 2009). Spatial and temporal monitoring of key geochemical and microbial (i.e., Geobacter lovleyi and Dehalococcoides mccartyi strains) parameters in the column generated a data set used herein as the basis for refinement and testing of a multiphase, compositional transport model. The refined model is capable of simulating the reactive transport of multiple chemical constituents produced and consumed by organohalide-respiring bacteria and accounts for substrate limitations and competitive inhibition. Parameter estimation techniques were used to optimize the values of sensitive microbial kinetic parameters, including maximum utilization rates, biomass yield coefficients, and endogenous decay rates. Comparison and calibration of model simulations with the experimental data demonstrate that the model is able to accurately reproduce measured effluent concentrations, while delineating trends in dechlorinator growth and reductive dechlorination kinetics along the column. Sensitivity analyses performed on the optimized model parameters indicate that the rates of PCE and cis-1,2-dichloroethene (cis-DCE) transformation and Dehalococcoides growth govern bioenhanced dissolution, as long as electron donor (i.e., hydrogen flux) is not limiting. Dissolution enhancements were shown to be independent of cis-DCE accumulation; however, accumulation of cis-DCE, as well as column length and flow rate (i.e., column residence time

Thermo-resistant filtration fabrics for hot gas extraction

International Nuclear Information System (INIS)

Wierzbowska, T.

1992-01-01

Types and technical and utilizing data of heat resistant filtrating fabrics initiated to production by 'Moratex' and provided for dust extraction of technical gas from various industrial processes have been discussed. (author). 8 refs, 2 tabs

Efficient indium-tin-oxide free inverted organic solar cells based on aluminum-doped zinc oxide cathode and low-temperature aqueous solution processed zinc oxide electron extraction layer

International Nuclear Information System (INIS)

Chen, Dazheng; Zhang, Chunfu; Wang, Zhizhe; Zhang, Jincheng; Tang, Shi; Wei, Wei; Sun, Li; Hao, Yue

2014-01-01

Indium-tin-oxide (ITO) free inverted organic solar cells (IOSCs) based on aluminum-doped zinc oxide (AZO) cathode, low-temperature aqueous solution processed zinc oxide (ZnO) electron extraction layer, and poly(3-hexylthiophene-2, 5-diyl):[6, 6]-phenyl C 61 butyric acid methyl ester blend were realized in this work. The resulted IOSC with ZnO annealed at 150 °C shows the superior power conversion efficiency (PCE) of 3.01%, if decreasing the ZnO annealing temperature to 100 °C, the obtained IOSC also shows a PCE of 2.76%, and no light soaking issue is observed. It is found that this ZnO film not only acts as an effective buffer layer but also slightly improves the optical transmittance of AZO substrates. Further, despite the relatively inferior air-stability, these un-encapsulated AZO/ZnO IOSCs show comparable PCEs to the referenced ITO/ZnO IOSCs, which demonstrates that the AZO cathode is a potential alternative to ITO in IOSCs. Meanwhile, this simple ZnO process is compatible with large area deposition and plastic substrates, and is promising to be widely used in IOSCs and other relative fields.

Characterization of technical surfaces by structure function analysis

Science.gov (United States)

Kalms, Michael; Kreis, Thomas; Bergmann, Ralf B.

2018-03-01

The structure function is a tool for characterizing technical surfaces that exhibits a number of advantages over Fourierbased analysis methods. So it is optimally suited for analyzing the height distributions of surfaces measured by full-field non-contacting methods. The structure function is thus a useful method to extract global or local criteria like e. g. periodicities, waviness, lay, or roughness to analyze and evaluate technical surfaces. After the definition of line- and area-structure function and offering effective procedures for their calculation this paper presents examples using simulated and measured data of technical surfaces including aircraft parts.

Technical design issues for a field-portable supercritical fluid extractor

Energy Technology Data Exchange (ETDEWEB)

Wright, B.W.; Zemanian, T.S.; Robins, W.H.; Wright, C.W.

1995-01-01

Supercritical fluid extraction is gaining acceptance as an alternative sample preparation method for trace organic analysis. The development of SFE instrumentation optimized for field use requires taking several technical design issues including size and weight requirements, user-friendly operation, and technical performance capabilities into consideration. Parameters associated with a prototype SFE instrument under development for potential use in conducting on-site inspections of the Chemical Weapons Convention and its preliminary technical and operational performance are described.

Technical structure of the global nanoscience and nanotechnology literature

Energy Technology Data Exchange (ETDEWEB)

Kostoff, Ronald N., E-mail: kostofr@onr.navy.mil; Koytcheff, Raymond G. [Office of Naval Research (United States); Lau, Clifford G. Y. [Institute for Defense Analyses (United States)

2007-10-15

Text mining was used to extract technical intelligence from the open source global nanotechnology and nanoscience research literature. An extensive nanotechnology/nanoscience-focused query was applied to the Science Citation Index/Social Science Citation Index (SCI/SSCI) databases. The nanotechnology/nanoscience research literature technical structure (taxonomy) was obtained using computational linguistics/document clustering and factor analysis. The infrastructure (prolific authors, key journals/institutions/countries, most cited authors/journals/documents) for each of the clusters generated by the document clustering algorithm was obtained using bibliometrics. Another novel addition was the use of phrase auto-correlation maps to show technical thrust areas based on phrase co-occurrence in Abstracts, and the use of phrase-phrase cross-correlation maps to show technical thrust areas based on phrase relations due to the sharing of common co-occurring phrases. The {approx}400 most cited nanotechnology papers since 1991 were grouped, and their characteristics generated. Whereas the main analysis provided technical thrusts of all nanotechnology papers retrieved, analysis of the most cited papers allowed their characteristics to be displayed. Finally, most cited papers from selected time periods were extracted, along with all publications from those time periods, and the institutions and countries were compared based on their representation in the most cited documents list relative to their representation in the most publications list.

Technical structure of the global nanoscience and nanotechnology literature

International Nuclear Information System (INIS)

Kostoff, Ronald N.; Koytcheff, Raymond G.; Lau, Clifford G. Y.

2007-01-01

Text mining was used to extract technical intelligence from the open source global nanotechnology and nanoscience research literature. An extensive nanotechnology/nanoscience-focused query was applied to the Science Citation Index/Social Science Citation Index (SCI/SSCI) databases. The nanotechnology/nanoscience research literature technical structure (taxonomy) was obtained using computational linguistics/document clustering and factor analysis. The infrastructure (prolific authors, key journals/institutions/countries, most cited authors/journals/documents) for each of the clusters generated by the document clustering algorithm was obtained using bibliometrics. Another novel addition was the use of phrase auto-correlation maps to show technical thrust areas based on phrase co-occurrence in Abstracts, and the use of phrase-phrase cross-correlation maps to show technical thrust areas based on phrase relations due to the sharing of common co-occurring phrases. The ∼400 most cited nanotechnology papers since 1991 were grouped, and their characteristics generated. Whereas the main analysis provided technical thrusts of all nanotechnology papers retrieved, analysis of the most cited papers allowed their characteristics to be displayed. Finally, most cited papers from selected time periods were extracted, along with all publications from those time periods, and the institutions and countries were compared based on their representation in the most cited documents list relative to their representation in the most publications list

Highly Efficient Flexible Quantum Dot Solar Cells with Improved Electron Extraction Using MgZnO Nanocrystals.

Science.gov (United States)

Zhang, Xiaoliang; Santra, Pralay Kanti; Tian, Lei; Johansson, Malin B; Rensmo, Håkan; Johansson, Erik M J

2017-08-22

Colloidal quantum dot (CQD) solar cells have high potential for realizing an efficient and lightweight energy supply for flexible or wearable electronic devices. To achieve highly efficient and flexible CQD solar cells, the electron transport layer (ETL), extracting electrons from the CQD solid layer, needs to be processed at a low-temperature and should also suppress interfacial recombination. Herein, a highly stable MgZnO nanocrystal (MZO-NC) layer is reported for efficient flexible PbS CQD solar cells. Solar cells fabricated with MZO-NC ETL give a high power conversion efficiency (PCE) of 10.4% and 9.4%, on glass and flexible plastic substrates, respectively. The reported flexible CQD solar cell has the record efficiency to date of flexible CQD solar cells. Detailed theoretical simulations and extensive characterizations reveal that the MZO-NCs significantly enhance charge extraction from CQD solids and diminish the charge accumulation at the ETL/CQD interface, suppressing charge interfacial recombination. These important results suggest that the low-temperature processed MZO-NCs are very promising for use in efficient flexible solar cells or other flexible optoelectronic devices.

Nuclear-technical applications in gold extraction metallurgy

International Nuclear Information System (INIS)

Smith, S.W.; De Jesus, A.S.M.

1986-01-01

Radioisotopes have been used for a number of years by the South African gold mining industry in a variety of measuring techniques, not only in conventional on-line process instrumentation, but also to investigate problem areas in extraction processes. These include, inter alia, tracer investigations on recirculating underground water, measurement of air ventilation rates in a mine, residence time measurements in milling and leaching circuits, and gold purity determinations. Applications of both sealed sources and radioactive tracer techniques are reviewed by means of examples of work done in South Africa, with pertinent reference to the benefits accruing to the gold mining industry

Protective effect of Hippophae rhamnoides leaf extract on gamma irradiation induced clastogenecity in mice

International Nuclear Information System (INIS)

Tyagi, Anuradha; Prasad, Jagdish; Bala, Madhu

2012-01-01

Hippophae rhamnoides (sea buckthorn) is a plant belonging to Elaeagnaceae family and is distributed worldwide. It has variety of uses from nutritional food to pharmacological application. The study was aimed to analyse the extract from Hippophae rhamnoides leaves for their possible protective effects against the whole body 60 Co-a-irradiation. The study was performed on six groups of male mice i.e. untreated group, H. rhamnoides extract group, irradiated (2Gy), irradiated (3Gy), H. rhamnoides and irradiated (2Gy) and H. rhamnoides and irradiated (3Gy). In each group micronucleus test was performed utilising bone marrow and peripheral blood. The mice were sacrificed 30 hrs after treatment and analysed for the presence of micronuclei. In the present study, there was no significant increase in the frequency of either micronucleated polychromatic erythrocytes (MNPCEs) or normochromatic erythrocytes (NCE) in H. rhamnoides extract treated group over the negative control group of animals, indicating its non-clastogenic and non-toxic activity in the erythropoietic system. H. rhamnoides extract showed good anti-clastogenic activity against the a-irradiation induced clastogenecity in both the tissues i.e. bone marrow and peripheral blood by reducing the frequency of micronuclei. Also the administration of H. rhamnoides extract along with irradiation was slightly able to increase the frequency of PCE in bone marrow as well as in peripheral blood in comparison to the irradiated group (2Gy and 3Gy) indicating its ability to reduce the toxicity caused by irradiation in the erythropoietic system. Thus the results indicate the non-clastogenic effect of H. rhamnoides leaf extract and significant protective activity against 60 Co-a-irradiation suggesting its pharmacological significance for development of radioprotector. (author)

Ocean Thermal Extractable Energy Visualization

Energy Technology Data Exchange (ETDEWEB)

Ascari, Matthew [Lockheed Martin Corporation, Bethesda, MD (United States)

2012-10-28

The Ocean Thermal Extractable Energy Visualization (OTEEV) project focuses on assessing the Maximum Practicably Extractable Energy (MPEE) from the world’s ocean thermal resources. MPEE is defined as being sustainable and technically feasible, given today’s state-of-the-art ocean energy technology. Under this project the OTEEV team developed a comprehensive Geospatial Information System (GIS) dataset and software tool, and used the tool to provide a meaningful assessment of MPEE from the global and domestic U.S. ocean thermal resources.

Development of technical specifications for research reactors

International Nuclear Information System (INIS)

Anon.

1983-01-01

This standard identifies and establishes the content of technical specifications for research reactors. Areas addressed are: definitions, safety limits, limiting safety system settings, limiting conditions for operation, surveillance requirements, design features and administrative controls. Sufficient detail is incorporated so that applicable specifications can be derived or extracted

Norm-Aware Socio-Technical Systems

Science.gov (United States)

Savarimuthu, Bastin Tony Roy; Ghose, Aditya

The following sections are included: * Introduction * The Need for Norm-Aware Systems * Norms in human societies * Why should software systems be norm-aware? * Case Studies of Norm-Aware Socio-Technical Systems * Human-computer interactions * Virtual environments and multi-player online games * Extracting norms from big data and software repositories * Norms and Sustainability * Sustainability and green ICT * Norm awareness through software systems * Where To, From Here? * Conclusions

Degradation study of trichloroethylene and perchloric ethylene using high energy electron beam generated in industrial accelerator

International Nuclear Information System (INIS)

Silva, B.L.R.; Sampa, M.H.O.; Avolio, R.M.; Somessari, E.S.R.; Vieira, J.M.; Rela, P.R.

1995-01-01

The pollution of potable water with chlorinated hydrocarbons, mainly trichloroethylene (TCE) and perchloric ethylene (PCE), is seriously increasing the problem of contamination of water, specially in highly industrialized areas. Recent studies show that depuration by ionizing radiation has been considered a possible alternative to the control of water pollution, wherein the process by ionizing radiation converts TCE and PCE into approximately 100% carbon dioxide ions. Water samples containing TCE e PCE were submitted to radiation in the pilot plant installed in the industrial electron accelerator at IPEN from Radiation Dynamics, Dynamitron II, of 1,5 MeV - 25 m A, with doses varying from 2 kGy to 8 kGy, being its parameters analyzed before and after irradiation TCE and PCE concentrations were determined by the gas chromatography method by liquid-liquid extraction using a gas chromatograph, model CG 90, with an electron capture detector. (author). 5 refs, 4 figs

Innovative and practical technical development of nuclear energy. Efforts on proposal and recruitment type technical development of nuclear energy

International Nuclear Information System (INIS)

Matsui, Kazuaki; Shioiri, Akio; Hamada, Jun; Kanagawa, Takashi; Mori, Yukihide; Kouno, Koji

2003-01-01

In technical development of nuclear energy conceiving a view on energy environment problem at the 21st Century, technical development on innovative nuclear energy system as well as next generation LWR is an important subject. Even in Japan, on the 'Long-term program for research, development and utilization of nuclear energy (LPRNE)' summarized by the Atomic Energy Commission, investigation on R and Ds of innovative reactors under cooperation of government, industrial field, and universities is required. In the Energy Generalized Engineering Institute, by receiving a subsidy from the Ministry of Economy and Industry since 2000, a proposal recruitment business on innovative and practical technical development of nuclear energy has been carried out. Here were introduced hopeful and unique five themes out of them applied to the recruitment, such as a super-critical pressure water cooling reactor (SCPR), an integrated modular LWR (IMR): technical development for practice, technical development on general purpose boiling transitional analysis method, technical development on direct extraction of U and Pu from consumed fuels based on super-DIREX reprocessing method, and material transfer forecasting in natural barriers at landfill disposal of radioactive wastes. (G.K.)

Effects of High Temperature and Thermal Cycling on the Performance of Perovskite Solar Cells: Acceleration of Charge Recombination and Deterioration of Charge Extraction

KAUST Repository

Sheikh, Arif D.

2017-09-18

In this work, we investigated the effects of high operating temperature and thermal cycling on the photovoltaic performance of perovskite solar cells (PSCs) with a typical mesostructured (m)-TiO2-CH3NH3PbI3-xClx-spiro-OMeTAD architecture. After carrying out temperature-dependent grazing incidence wide-angle X-ray scattering (GIWAXS), in-situ X-ray diffraction (XRD) and optical absorption experiments, thermal durability of PSCs was tested by subjecting the devices to repetitive heating to 70 °C and cooling to room temperature (20 °C). An unexpected regenerative effect was observed after the first thermal cycle; the average power conversion efficiency (PCE) increased by approximately 10 % in reference to the as-prepared device. This increase of PCE was attributed to the heating-induced improvement of crystallinity and p-doping in the hole-transporter, Spiro-OMeTAD, which promotes the efficient extraction of photo-generated carriers. However, further thermal cycles produced a detrimental effect on the photovoltaic performance of PSCs with short-circuit current and fill factor degrading faster than the open-circuit voltage. Similarly, the photovoltaic performance of PSCs degraded at high operation temperatures; both short-circuit current and open-circuit voltage decreased with increasing temperature, but the temperature-dependent trend of fill factor was opposite. Our impedance spectroscopy analysis revealed a monotonous increase of charge transfer resistance and a concurrent decrease of charge recombination resistance with increasing temperature, indicating high recombination of charge carriers. Our results revealed that both thermal cycling and high temperatures produce irreversible detrimental effects on the PSC performance due to the deteriorated interfacial photo-carrier extraction. The present findings suggest that development of robust charge transporters and proper interface engineering are critical for the deployment of perovskite photovoltaics in harsh

Acute genotoxicity analysis in vivo of the aqueous extract of Maytenus guyanensis Amazonian chichuá

Directory of Open Access Journals (Sweden)

Dionatas Ulises de Oliveira Meneguetti

Full Text Available Abstract The species Maytenus guyanensis Klotzsch ex Reissek, Celastraceae, present a wide variety of possible pharmacological activities and its roots and stems are used by popular medicine in the western Amazon rainforest. Few studies have demonstrated the genotoxic safety of the popular use of this species, and owing to this, the present study aimed to perform an analysis of the acute genotoxicity in vivo of the aqueous extract of M. guyanensis. Male and female mice from Mus musculus species, of weights ranging from 20 to 40 g, organized in eight groups with different treatments were used. The aqueous extracts of the bark of M. guyanensis were administered orally by gavage with 0.1 ml of the test substance per 10 g of the animal, followed by performance of comet assay in peripheral blood, PCE/NCE correlation and occurrence of micronuclei in the bone marrow. It was found that the aqueous extract of M. guyanensis, with ten times higher concentration than those used in ethnopharmacology, did not present genotoxic effect and, moreover, it has antigenotoxic action in mice treated acutely. Further studies regarding bioaccumulation and chronic effects of this species are suggested, in order to improve the understanding of its mechanism of action, ensuring the efficacy and safety of its utilization and developing phytotherapics and drugs.

Algal Lipid Extraction and Upgrading to Hydrocarbons Technology Pathway

Energy Technology Data Exchange (ETDEWEB)

Davis, R.; Biddy, M.; Jones, S.

2013-03-01

This technology pathway case investigates the cultivation of algal biomass followed by further lipid extraction and upgrading to hydrocarbon biofuels. Technical barriers and key research needs have been assessed in order for the algal lipid extraction and upgrading pathway to be competitive with petroleum-derived gasoline-, diesel-, and jet-range hydrocarbon blendstocks.

Physicochemical basics for production of uranium concentrate from wastes of hydrometallurgical plants and technical waters

International Nuclear Information System (INIS)

Khakimov, N.; Nazarov, Kh.M.; Khojiyon, M.; Mirsaidov, I.U.; Nazarov, K.M.; Barotov, B.B.

2012-01-01

Physicochemical and technological basics for reprocessing of uranium industry wastes of Northern Tajikistan shows that the most perspective for reprocessing is Chkalovsk tailing's wastes. Engineer and geological condition and content of radionuclides in wastes are investigated. It is determined that considered wastes by radioactivity are low-active and they can be reprocessed with the purpose of U 3 O 8 production. Grinding, crumbling, thickening and etc. operations are decreased during the wastes reprocessing process. Uranium output is more than 90%. Optimal parameters of products extraction from uranium mining industry wastes are found. Characteristics of mine and technical waters of uranium industry wastes are studied. Characteristics of mine and technical waters of Kiik-Tal and Istiklol city (former Taboshar) showed the expediency of uranium oxide extraction from them. The reasons for non-additional recovery extraction from dumps of State Enterprise 'Vostokredmet' by classical methods of uranium leaching are studied. Kinetics of sulfuric leaching of residues from anthropogenic deposit of Map 1-9 (Chkalovsk city) is investigated. Carried out investigations are revealing the flow mechanism process of residues' sulfuric leaching and enable selection of radiation regime of U 3 O 8 production. Kinetics of sorption process of uranium extraction from mine and technical waters of uranium industry wastes is studied. High sorption properties of apricot's shell comparing to other sorbents are revealed. Basic process flow diagram for reprocessing of uranium tailing wastes is developed as well as diagram for uranium extraction from mine and technical waters from uranium industry wastes which consists of the following stages: acidification, sorption, burning, leaching, sedimentation, filtration, drying.

Sodium bromide electron-extraction layers for polymer bulk-heterojunction solar cells

International Nuclear Information System (INIS)

Gao, Zhi; Qu, Bo; Xiao, Lixin; Chen, Zhijian; Zhang, Lipei; Gong, Qihuang

2014-01-01

Inexpensive and non-toxic sodium bromide (NaBr) was introduced into polymer solar cells (PSCs) as the cathode buffer layer (CBL) and the electron extraction characteristics of the NaBr CBL were investigated in detail. The PSCs based on NaBr CBL with different thicknesses (i.e., 0 nm, 0.5 nm, 1 nm, and 1.5 nm) were prepared and studied. The optimal thickness of NaBr was 1 nm according to the photovoltaic data of PSCs. The open-circuit voltage (V oc ), short-circuit current density (J sc ), fill factor (FF), and power conversion efficiency (PCE) of the PSC with 1 nm NaBr were evaluated to be 0.58 V, 7.36 mA/cm 2 , 0.63, and 2.70%, respectively, which were comparable to those of the reference device with the commonly used LiF. The optimized photovoltaic performance of PSC with 1 nm NaBr was ascribed to the improved electron transport and extraction capability of 1 nm NaBr in PSCs. In addition, the NaBr CBL could prevent the diffusion of oxygen and water vapor into the active layer and prolong the lifetime of the devices to some extent. Therefore, NaBr layer could be considered as a promising non-toxic CBL for PSCs in future

Technical reproducibility of single-nucleotide and size-based DNA biomarker assessment using DNA extracted from formalin-fixed, paraffin-embedded tissues.

Science.gov (United States)

Zhang, Shenli; Tan, Iain B; Sapari, Nur S; Grabsch, Heike I; Okines, Alicia; Smyth, Elizabeth C; Aoyama, Toru; Hewitt, Lindsay C; Inam, Imran; Bottomley, Dan; Nankivell, Matthew; Stenning, Sally P; Cunningham, David; Wotherspoon, Andrew; Tsuburaya, Akira; Yoshikawa, Takaki; Soong, Richie; Tan, Patrick

2015-05-01

DNA extracted from formalin-fixed, paraffin-embedded (FFPE) tissues has been used in the past to analyze genetic polymorphisms. We evaluated the technical reproducibility of different types of assays for gene polymorphisms using DNA extracted from FFPE material. By using the MassARRAY iPLEX system, we investigated polymorphisms in DPYD (rs1801159 and rs3918290), UMPS (rs1801019), ERCC1 (rs11615), ERCC1 (rs3212986), and ERCC2 (rs13181) in 56 FFPE DNA samples. By using PCR, followed by size-based gel electrophoresis, we also examined TYMS 5' untranslated region 2R/3R repeats and GSTT1 deletions in 50 FFPE DNA samples and 34 DNAs extracted from fresh-frozen tissues and cell lines. Each polymorphism was analyzed by two independent runs. We found that iPLEX biomarker assays measuring single-nucleotide polymorphisms provided consistent concordant results. However, by using FFPE DNA, size-based PCR biomarkers (GSTT1 and TYMS 5' untranslated region) were discrepant in 32.7% (16/49, with exact 95% CI, 19.9%-47.5%; exact binomial confidence limit test) and 4.2% (2/48, with exact 95% CI, 0.5%-14.3%) of cases, respectively, whereas no discrepancies were observed using intact genomic DNA. Our findings suggest that DNA from FFPE material can be used to reliably test single-nucleotide polymorphisms. However, results based on size-based PCR biomarkers, and particularly GSTT1 deletions, using FFPE DNA need to be interpreted with caution. Independent repeated assays should be performed on all cases to assess potential discrepancies. Copyright © 2015 American Society for Investigative Pathology and the Association for Molecular Pathology. Published by Elsevier Inc. All rights reserved.

Automatic River Network Extraction from LIDAR Data

Science.gov (United States)

Maderal, E. N.; Valcarcel, N.; Delgado, J.; Sevilla, C.; Ojeda, J. C.

2016-06-01

National Geographic Institute of Spain (IGN-ES) has launched a new production system for automatic river network extraction for the Geospatial Reference Information (GRI) within hydrography theme. The goal is to get an accurate and updated river network, automatically extracted as possible. For this, IGN-ES has full LiDAR coverage for the whole Spanish territory with a density of 0.5 points per square meter. To implement this work, it has been validated the technical feasibility, developed a methodology to automate each production phase: hydrological terrain models generation with 2 meter grid size and river network extraction combining hydrographic criteria (topographic network) and hydrological criteria (flow accumulation river network), and finally the production was launched. The key points of this work has been managing a big data environment, more than 160,000 Lidar data files, the infrastructure to store (up to 40 Tb between results and intermediate files), and process; using local virtualization and the Amazon Web Service (AWS), which allowed to obtain this automatic production within 6 months, it also has been important the software stability (TerraScan-TerraSolid, GlobalMapper-Blue Marble , FME-Safe, ArcGIS-Esri) and finally, the human resources managing. The results of this production has been an accurate automatic river network extraction for the whole country with a significant improvement for the altimetric component of the 3D linear vector. This article presents the technical feasibility, the production methodology, the automatic river network extraction production and its advantages over traditional vector extraction systems.

AUTOMATIC RIVER NETWORK EXTRACTION FROM LIDAR DATA

Directory of Open Access Journals (Sweden)

E. N. Maderal

2016-06-01

Full Text Available National Geographic Institute of Spain (IGN-ES has launched a new production system for automatic river network extraction for the Geospatial Reference Information (GRI within hydrography theme. The goal is to get an accurate and updated river network, automatically extracted as possible. For this, IGN-ES has full LiDAR coverage for the whole Spanish territory with a density of 0.5 points per square meter. To implement this work, it has been validated the technical feasibility, developed a methodology to automate each production phase: hydrological terrain models generation with 2 meter grid size and river network extraction combining hydrographic criteria (topographic network and hydrological criteria (flow accumulation river network, and finally the production was launched. The key points of this work has been managing a big data environment, more than 160,000 Lidar data files, the infrastructure to store (up to 40 Tb between results and intermediate files, and process; using local virtualization and the Amazon Web Service (AWS, which allowed to obtain this automatic production within 6 months, it also has been important the software stability (TerraScan-TerraSolid, GlobalMapper-Blue Marble , FME-Safe, ArcGIS-Esri and finally, the human resources managing. The results of this production has been an accurate automatic river network extraction for the whole country with a significant improvement for the altimetric component of the 3D linear vector. This article presents the technical feasibility, the production methodology, the automatic river network extraction production and its advantages over traditional vector extraction systems.

Phase II trial of combination treatment with paclitaxel, carboplatin and cetuximab (PCE) as first-line treatment in patients with recurrent and/or metastatic squamous cell carcinoma of the head and neck (CSPOR-HN02).

Science.gov (United States)

Tahara, M; Kiyota, N; Yokota, T; Hasegawa, Y; Muro, K; Takahashi, S; Onoe, T; Homma, A; Taguchi, J; Suzuki, M; Minato, K; Yane, K; Ueda, S; Hara, H; Saijo, K; Yamanaka, T

2018-04-01

The standard of care for first-line treatment of recurrent and/or metastatic squamous cell carcinoma of the head and neck (R/M SCCHN) is combination treatment with platinum, 5-FU and cetuximab (PFE). However, this regimen requires hospitalization to ensure proper hydration and continuous infusion of 5-FU, and causes severe nausea and anorexia. We evaluated the efficacy and safety of paclitaxel, carboplatin and cetuximab (PCE) as first-line treatment in patients with R/M SCCHN. Eligibility criteria included recurrent and/or metastatic, histologically proven SCC of the oropharynx, oral cavity, hypopharynx or larynx; PS 0-1; adequate organ function; no suitable local therapy for R/M SCCHN; and no prior systemic chemotherapy for R/M SCCHN. Chemotherapy consisted of paclitaxel 100 mg/m2 on days 1, 8; carboplatin area under the blood concentration-time curve 2.5 on days 1, 8, repeated every 3 weeks for up to 6 cycles; and cetuximab at an initial dose of 400 mg/m2, followed by 250 mg/m2 weekly until disease progression or unacceptable toxicities. Primary end point was overall response rate. Secondary end points were safety, treatment completion rate, progression-free survival, overall survival, and clinical benefit rate. Planned sample size was 45 patients. Forty-seven subjects were accrued from July 2013 to October 2014. Of 45 evaluable, 40 were male; median age was 63 years; Eastern Cooperative Oncology Group Performance Status was 0/1 in 23/22 cases; site was the hypopharynx/oropharynx/oral cavity/larynx in 17/11/10/7 cases; and 36/9 cases were smokers/nonsmokers, respectively. Overall response rate, the primary end point, was 40%. Median overall survival was 14.7 months and progression-free survival was 5.2 months. Grade 3/4 adverse events included neutropenia (68%), skin reaction (15%), fatigue (9%) and febrile neutropenia (9%). A potentially treatment-related death occurred in one patient with intestinal pneumonia. The PCE regimen shows promising

Physicochemical basics for production of uranium concentrate from wastes of hydrometallurgical plants and technical waters

International Nuclear Information System (INIS)

Khakimov, N.; Nazarov, Kh.M.; Khojiyon, M.; Mirsaidov, I.U.; Nazarov, K.M.; Barotov, B.B.

2012-01-01

Physicochemical and technological basics for reprocessing of uranium industry wastes of Northern Tajikistan shows that the most perspective for reprocessing is Chkalovsk tailing's wastes. Engineer and geological condition and content of radionuclides in wastes are investigated. It is determined that considered wastes by radioactivity are low-active and they can be reprocessed with the purpose of U 3 O 8 production. Grinding, crumbling, thickening and etc. operations are decreased during the wastes reprocessing process. Uranium output is more than 90%. Optimal parameters of products extraction from uranium mining industry wastes are found. Characteristics of mine and technical waters of uranium industry wastes are studied. Characteristics of mine and technical waters of Kiik-Tal and Istiklol city (former Taboshar) showed the expediency of uranium oxide extraction from them. The reasons for non-additional recovery extraction from dumps of State Enterprise 'Vostokredmet' by classical methods of uranium leaching are studied. Kinetics of sulfuric leaching of residues from anthropogenic deposit of Map 1-9 (Chkalovsk city) is investigated. Carried out investigations are revealing the flow mechanism process of residues' sulfuric leaching and enable selection of radiation regime of U 3 O 8 production. Kinetics of sorption process of uranium extraction from mine and technical waters of uranium industry wastes is studied. High sorption properties of apricot's shell comparing to other sorbents are revealed. Basic process flow diagram for reprocessing of uranium tailing wastes is developed as well as diagram for uranium extraction from mine and technical waters from uranium industry wastes which consists of the following stages: acidification, sorption, burning, leaching, sedimentation, filtration, drying.

Salubrious effect of Parinari curatellifolia seed extract in doxorubicin ...

African Journals Online (AJOL)

Catechin, epicatechin, quercetin, isoquercitrin, rutin, kaempferol and quercitrin were confirmed present in PCE. DOX intoxication in experimental rats resulted in significant increase (P<0.05) in plasma activities of LDH and CK-MB, concentrations of all lipid types, except HDL which was significantly (P<0.05) reduced, as well ...

Methods of thermal power extraction from nuclear sources for meeting the consumer system demands

International Nuclear Information System (INIS)

Sellej, J.

1985-01-01

The technical design is discussed of heat extraction from nuclear power plants and heating plants. Variant technical designs are discussed of hot water and steam supply, including the basic aspects of nuclear safety. Hot water supplies are technically provided by heat exchanger units connected to turbines, or by heating turbines. The advantages and disadvantages of the two designs are discussed. The possibility of heat extraction by steam from the nuclear power plant is provided by steam exchangers, i.e., steam exchanger cascades, the so-called inserted steam circuit. Supplies of steam from nuclear sources, as against supplies of hot water have not yet been technically resolved with regard to safety, design and economic benefit. Nuclear heating plants have also been designed for hot water supply, but not yet for steam supply. (Pu)

Technical writing versus technical writing

Science.gov (United States)

Dillingham, J. W.

1981-01-01

Two terms, two job categories, 'technical writer' and 'technical author' are discussed in terms of industrial and business requirements and standards. A distinction between 'technical writing' and technical 'writing' is made. The term 'technical editor' is also considered. Problems inherent in the design of programs to prepare and train students for these jobs are discussed. A closer alliance between industry and academia is suggested as a means of preparing students with competent technical communication skills (especially writing and editing skills) and good technical skills.

Electromembrane extraction as a rapid and selective miniaturized sample preparation technique for biological fluids

DEFF Research Database (Denmark)

Gjelstad, Astrid; Pedersen-Bjergaard, Stig; Seip, Knut Fredrik

2015-01-01

This special report discusses the sample preparation method electromembrane extraction, which was introduced in 2006 as a rapid and selective miniaturized extraction method. The extraction principle is based on isolation of charged analytes extracted from an aqueous sample, across a thin film....... Technical aspects of electromembrane extraction, important extraction parameters as well as a handful of examples of applications from different biological samples and bioanalytical areas are discussed in the paper....

Physico-chemical basics for production of uranium concentrate from wastes of hydrometallurgical plants and technical waters

International Nuclear Information System (INIS)

Mirsaidov, I.; Nazarov, K.

2014-01-01

Physico-chemical and technological basics for reprocessing of uranium industry wastes of Northern Tajikistan shows that the most perspective site for reprocessing is Chkalovkst tailings wastes. The engineering and geological conditions and content of radionuclides in wastes were investigated. It was determined that considered by radioactivity the wastes are low activity and they can be reprocessed for the purpose of U_3O_8 production. Characteristics of mine and technical waters of uranium industry wastes were studied. Characteristics of mine and technical waters of Kiik-Tal and Istiklol city (former Taboshar) showed the expediency of uranium oxide extraction from them. The reasons for non-additional recovery extraction from dumps of SE “Vostokredmet” by classical methods of uranium leaching are studied. The kinetics of sulfuric leaching of residues from anthropogenic deposit of Map 1-9 (Chkalovsk City) were also investigated. Further investigations are to reveal the flow mechanism process of sulfuric leaching of residues and to enable the selection of a radiation regime for U_3O_8 production. The kinetics of sorption process of uranium extraction from mine and technical waters of uranium industry wastes were studied. High sorption properties of apricot shell compared to other sorbents were revealed. A basic process flow diagram for reprocessing of uranium tailing wastes was developed as well as diagrams for uranium extraction from mine and technical waters from uranium industry wastes. The process consists of the following stages: acidification, sorption, burning, leaching, sedimentation, filtration and drying. The possibility of uranium extraction from natural uranic waters of a complicated salt composition was considered. Investigations revealed that uranium extraction from brines containing chloride ion is possible. A developed uranium extraction scheme from Sasik-Kul lake’s brine consists of the following main stages: evaporation, leaching, chloride

Electromembrane extraction – Recent trends and where to go

DEFF Research Database (Denmark)

Pedersen-Bjergaard, Stig; Huang, Chuixiu; Gjelstad, Astrid

2017-01-01

Electromembrane extraction (EME) is an analytical microextraction technique, where charged analytes (such as drug substances) are extracted from an aqueous sample (such as a biological fluid), through a supported liquid membrane (SLM) comprising a water immiscible organic solvent......, papers published in 2016 are reviewed and discussed with focus on (a) new SLMs, (b) new support materials for the SLM, (c) new sample additives improving extraction, (d) new technical configurations, (e) improved theoretical understanding, and (f) pharmaceutical new applications. Finally, important...

The development of technical literature for the specification of fume extraction systems

Energy Technology Data Exchange (ETDEWEB)

Gibbons, A [Plastic Fabrications and Environmental Technology Ltd., Armagh (United Kingdom)

1996-12-31

The processes involved in producing technical literature to assist in the selection of fans are discussed. Desktop publishing has been found to provide an effective method of matching the detail of the literature to the needs of the customer. (author)

Enhanced Charge Extraction of Li-Doped TiO₂ for Efficient Thermal-Evaporated Sb₂S₃ Thin Film Solar Cells.

Science.gov (United States)

Lan, Chunfeng; Luo, Jingting; Lan, Huabin; Fan, Bo; Peng, Huanxin; Zhao, Jun; Sun, Huibin; Zheng, Zhuanghao; Liang, Guangxing; Fan, Ping

2018-02-28

We provided a new method to improve the efficiency of Sb₂S₃ thin film solar cells. The TiO₂ electron transport layers were doped by lithium to improve their charge extraction properties for the thermal-evaporated Sb₂S₃ solar cells. The Mott-Schottky curves suggested a change of energy band and faster charge transport in the Li-doped TiO₂ films. Compared with the undoped TiO₂, Li-doped mesoporous TiO₂ dramatically improved the photo-voltaic performance of the thermal-evaporated Sb₂S₃ thin film solar cells, with the average power conversion efficiency ( PCE ) increasing from 1.79% to 4.03%, as well as the improved open-voltage ( V oc ), short-circuit current ( J sc ) and fill factors. The best device based on Li-doped TiO₂ achieved a power conversion efficiency up to 4.42% as well as a V oc of 0.645 V, which are the highest values among the reported thermal-evaporated Sb₂S₃ solar cells. This study showed that Li-doping on TiO₂ can effectively enhance the charge extraction properties of electron transport layers, offering a new strategy to improve the efficiency of Sb₂S₃-based solar cells.

DFT Calculation of IR Absorption Spectra for PCE-nH2O, TCE-nH2O, DCE-nH2O, VC-nH2O for Small and Water-Dominated Molecular Clusters

Science.gov (United States)

2017-10-31

VC-nH2O for Small and Water-Dominated Molecular Clusters October 31, 2017 Approved for public release; distribution is unlimited. L. Huang S.g...Calculation of IR Absorption Spectra for PCE-nH2O, TCE-nH2O, DCE-nH2O, VC-nH2O for Small and Water-Dominated Molecular Clusters L. Huang,1 S.G...nH2O molecular clusters using density function theory (DFT). DFT can provide interpretation of absorption spectra with respect to molecular

Identification of active dehalorespiring microbial populations in anoxic river sediment by RNA-based stable isotope probing

Science.gov (United States)

Kittelmann, S.; Friedrich, M. W.

2005-12-01

Tetrachloroethene (perchloroethylene, PCE), a persistent contaminant in aquifers, soils and sediments, can be reductively dechlorinated by anaerobic microorganisms in a process referred to as dehalorespiration. However, the biodiversity of dehalorespiring microorganisms and their distribution especially in pristine environments is largely unexplored. Therefore, the aim of this study was to detect potentially novel PCE-dehalorespiring microorganisms by using stable isotope probing (SIP), a technique that allows to directly identify the function of uncultivated microbial populations. We simulated a PCE contamination by incubating pristine river sediment in the presence of PCE at a steady, low aqueous concentration (20 μM). Dehalogenation activity in microcosms (20 nmol cis-dichloroethene per ml slurry per day formed) was detected already after 4 weeks at 20°C with sediment indigenous electron donors. The microbial community in sediment incubations was probed with 13C-labelled acetate (0.5 mM) as electron donor and carbon source at 15°C for 3 days. After RNA extraction, "heavy" 13C-rRNA and light 12C-rRNA were separated by isopycnic centrifugation, and Bacteria-related populations in gradient fractions were characterised by terminal restriction fragment length polymorphism analysis and cloning. In heavy gradient fractions from the microcosm with PCE, we detected a prominent 506-bp terminal restriction fragment (T-RF) and a few minor T-RFs only. In contrast, in the control without PCE, Bacteria-specific rRNA was restricted to light gradient fractions, and the prominent T-RFs found in the PCE-dechlorinating microcosm were of minor importance. Apparently, 13C-acetate was incorporated into bacterial rRNA more effectively in PCE-respiring microcosms. Thus, rRNA-SIP provides strong evidence for the presence of PCE-dehalorespiring, 13C-acetate-utilising populations in river sediment microcosms. Cloning/sequencing analysis identified the prominent members of the heavy

Extractive metallurgy. Recent advances

International Nuclear Information System (INIS)

Stevenson, E.J.

1977-01-01

Detailed technical information derived from patents issued since 1975 on extractive metallurgy is presented. In part one, concerning copper, the major areas covered are: smelting and roasting; acid leaching; ammonia leach processes; cuprous chloride and ferric chloride; and recovery of copper values from solution. Part two covers other metals, including: nickel and cobalt; ocean floor nodules; lead, zinc, molybdenum and manganese; precious metals; and uranium titanium, tantalum, rhenium, gallium, and other metals

Mathematical model for optimizing the design extraction pressure of a condensation turbine with district heat extraction. Mathematisches Modell zur Optimierung des Auslegungsentnahmedruckes an einer Kondensationsturbine mit Fernwaermeauskopplung

Energy Technology Data Exchange (ETDEWEB)

Grkovic, V [Novi Sad Univ. (Yugoslavia)

1991-11-01

A mathematical calculation model is explained, which enables optimization of the design pressure at the steam extraction point of a condensation extraction turbine. The results obtained show that the additional thermodynamic losses, which occur during turbine operation on variation of the heat load, can be reduced to a minimum by optimization of the extraction pressure. The optimal pressures at the extraction point, as well as the size of the economic effect are dependent on the selected technical design of the turbine, its maximum heat output and the basic heat load factor. (orig.).

Development of knowledge models by linguistic analysis of lexical relationships in technical documents

International Nuclear Information System (INIS)

Seguela, Patrick

2001-01-01

This research thesis addresses the problem of knowledge acquisition and structuring from technical texts, and the use of this knowledge in the development of models. The author presents the Cameleon method which aims at extracting binary lexical relationships from technical texts by identifying linguistic markers. The relevance of this method is assessed in the case of four different corpuses: a written technical corpus, an oral technical corpus, a corpus of texts of instructions, and a corpus of academic texts. The author reports the development of a model of representation of knowledge of a specific field by using lexical relationships. The method is then applied to develop a model used in document search within a knowledge management system [fr

Recent patents on the extraction of carotenoids.

Science.gov (United States)

Riggi, Ezio

2010-01-01

This article reviews the patents that have been presented during the last decade related to the extraction of carotenoids from various forms of organic matter (fruit, vegetables, animals), with an emphasis on the methods and mechanisms exploited by these technologies, and on technical solutions for the practical problems related to these technologies. I present and classify 29 methods related to the extraction processes (physical, mechanical, chemical, and enzymatic). The large number of processes for extraction by means of supercritical fluids and the growing number of large-scale industrial plants suggest a positive trend towards using this technique that is currently slowed by its cost. This trend should be reinforced by growing restrictions imposed on the use of most organic solvents for extraction of food products and by increasingly strict waste management regulations that are indirectly promoting the use of extraction processes that leave the residual (post-extraction) matrix substantially free from solvents and compounds that must subsequently be removed or treated. None of the reviewed approaches is the best answer for every extractable compound and source, so each should be considered as one of several alternatives, including the use of a combination of extraction approaches.

Effect of Ethanol Leaf Extract of Newboulda Laevis on Blood ...

African Journals Online (AJOL)

Erah

ethanol extract Newbouldia laevis and the fifth group received a reference standard, glibenclamide (5 mg/kg). Treatment ... presence of saponins, tannins, alkaloids and flavonoids. Conclusion: ..... City for his technical assistance in the course.

Technical feasibility of advanced separation; Faisabilite technique de la separation poussee

Energy Technology Data Exchange (ETDEWEB)

Rostaing, Ch

2004-07-01

Advanced separation aims at reducing the amount and toxicity of high-level and long lived radioactive wastes. The Purex process has been retained as a reference way for the recovery of the most radio-toxic elements: neptunium, technetium and iodine. Complementary solvent extraction processes have to be developed for the separation of americium, curium and cesium from the high activity effluent of the spent fuel reprocessing treatment. Researches have been carried out with the aim of demonstrating the scientifical and technical feasibility of advanced separation of minor actinides and long lived fission products from spent fuels. The scientifical feasibility was demonstrated at the end of 2001. The technical feasibility works started in the beginning of 2002. Many results have been obtained which are presented and summarized in this document: approach followed, processes retained for the technical feasibility (An/Ln and Am/Cm separation), processes retained for further validation at the new shielded Purex installation, technical feasibility of Purex adaptation to Np separation, technical feasibility of Diamex (first step: (An+Ln)/other fission products) separation), technical feasibility of Sanex process (second step: An(III)/Ln(III) separation), technical feasibility of Am(III)/Cm(III) separation, cesium separation, iodine separation, technical-economical evaluation, conclusions and perspectives, facilities and apparatuses used for the experiments. (J.S.)

Considerations on a new fast extraction kicker concept for SPS

CERN Document Server

Barnes, M

2010-01-01

An alternative extraction kicker concept is investigated for the SPS, based on open C-type kickers and a fast-bumper system. The beam is moved into the kicker gap some tens of ms before extraction. The concept is illustrated in detail with the LSS4 extraction from the SPS – very similar parameters and considerations apply to LSS6. A similar concept could also be conceived for injection but is more difficult due to the larger beam size. The technical issues are presented and the potential impact on the machine impedance outlined.

Triiodothyronine radioimmunoassay. Comparison of the different factors between two technics

International Nuclear Information System (INIS)

Gehin-Fouque, F.; Etling, N.; Pradelles, P.; Bornet, H.

1980-01-01

Triiodothyronine concentration was determined in human serum and in thyroid extracts by two radioimmunoassay technics. Both antibodies, radioactive T 3 , stable T 3 , protein-binding-hormone inhibitors, methods used to separate the free from the bound fractions were different. Each factor from a method was substituted to the homologue of the other method. The results occasionnally showed a variation of 32% in the first method and 50% in the second one. However the results gave a correct interpretation of the triiodothyronine values measured in human serum and in thyroid extracts [fr

Analytical and preparative separation of organic acids from water by extraction with trioctylamine

International Nuclear Information System (INIS)

Eberle, S.H.; Hoyer, O.; Knobel, K.P.; Hodenberg, S. von

1977-12-01

The extraction of pure organic acids and of humic and ligninsulfonic acid from water by a solution of trioctylamine in chloroform was investigated (technical grade amine = ALAMINE). Quantitative separation is achieved by double extraction with 5% ALAMINE at pH 3,5 - 4. The acids may be back-extracted with dilute sodium hydroxide solution. Procedures are described for the analytical extraction of water samples of 200 to 2.000 ml and for the flow-through processing of large water volumes. (orig.) [de

Reductive tetrachloroethene dehalogenation in the presence of oxygen by Sulfurospirillum multivorans: physiological studies and proteome analysis.

Science.gov (United States)

Gadkari, Jennifer; Goris, Tobias; Schiffmann, Christian L; Rubick, Raffael; Adrian, Lorenz; Schubert, Torsten; Diekert, Gabriele

2018-01-01

Reductive dehalogenation of organohalides is carried out by organohalide-respiring bacteria (OHRB) in anoxic environments. The tetrachloroethene (PCE)-respiring Epsilonproteobacterium Sulfurospirillum multivorans is one of few OHRB able to respire oxygen. Therefore, we investigated the organism's capacity to dehalogenate PCE in the presence of oxygen, which would broaden the applicability to use S. multivorans, unlike other commonly oxygen-sensitive OHRB, for bioremediation, e.g. at oxic/anoxic interphases. Additionally, this has an impact on our understanding of the global halogen cycle. Sulfurospirillum multivorans performs dehalogenation of PCE to cis-1,2-dichloroethene at oxygen concentrations below 0.19 mg/L. The redox potential of the medium electrochemically adjusted up to +400 mV had no influence on reductive dehalogenation by S. multivorans in our experiments, suggesting that higher levels of oxygen impair PCE dechlorination by inhibiting or inactivating involved enzymes. The PCE reductive dehalogenase remained active in cell extracts of S. multivorans exposed to 0.37 mg/L oxygen for more than 96 h. Analysis of the proteome revealed that superoxide reductase and cytochrome peroxidase amounts increased with 5% oxygen in the gas phase, while the response to atmospheric oxygen concentrations involved catalase and hydrogen peroxide reductase. Taken together, our results demonstrate that reductive dehalogenation by OHRB is not limited to anoxic conditions. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Optimized protein extraction for quantitative proteomics of yeasts.

Directory of Open Access Journals (Sweden)

Tobias von der Haar

2007-10-01

Full Text Available The absolute quantification of intracellular protein levels is technically demanding, but has recently become more prominent because novel approaches like systems biology and metabolic control analysis require knowledge of these parameters. Current protocols for the extraction of proteins from yeast cells are likely to introduce artifacts into quantification procedures because of incomplete or selective extraction.We have developed a novel procedure for protein extraction from S. cerevisiae based on chemical lysis and simultaneous solubilization in SDS and urea, which can extract the great majority of proteins to apparent completeness. The procedure can be used for different Saccharomyces yeast species and varying growth conditions, is suitable for high-throughput extraction in a 96-well format, and the resulting extracts can easily be post-processed for use in non-SDS compatible procedures like 2D gel electrophoresis.An improved method for quantitative protein extraction has been developed that removes some of the sources of artefacts in quantitative proteomics experiments, while at the same time allowing novel types of applications.

Kinetic models for supercritical CO2 extraction of oilseeds - a review

Directory of Open Access Journals (Sweden)

B. Nagy

2011-01-01

Full Text Available The supercritical fluid extraction of oilseeds is gaining increasing interest in commercial application for the last few decades, most particularly thanks to technical and environmental advantages of supercritical fluid extraction technology compared to current extraction methods with organic solvents. Furthermore, CO2 as a solvent is generally recognized as safe (GRAS. At present moment, supercritical fluid extractions on a commercial scale are limited to decaffeination, production of soluble hops extracts, sesame seed oil production and extraction of certain petroleum products. When considering industrial application, it is essential to test the applicability of the appropriate model for supercritical fluid extraction of oilseeds used for scale up of laboratory data to industrial design purposes. The aim of this paper is to review the most significant kinetic models reported in the literature for supercritical fluid extraction.

Antigenotoxic potential of Asparagus racemosus root extract against electron beam radiation induced micronuclei formation in Swiss albino mice

International Nuclear Information System (INIS)

Bhandary, B. Satheesh Kumar; Sharmila, K.P.; Suchetha Kumari, N.; Bhat, Vadish S.; Shetty, Jayaram; Peter, Alex John; Jose, Jerish M.; Fernandes, Ronald

2016-01-01

To evaluate the antigenotoxic potential of Asparagus Racemosus Root ethanolic extract (ARE) against electron beam radiation induced micronuclei formation in Swiss albino mice. Micronucleus assay was performed in the bone marrow of Swiss albino mice according to the method of Hosseinimehr et al., 2003. The experimental animals were orally administered 200 mg/kg body weight of ARE once daily for 15 consecutive days. At the end of experimental period, the animals were euthanized and the bone marrow was collected from the femur. Control (C), Radiation control (RC) and drug control (DC) group was also maintained. The number of radiation induced Micronucleated Polychromatic Erythrocytes (MnPCE) and Micronucleated Normochromatic Erythrocytes were decreased in the ARE treated mice which was statistically significant (p<0.05) compared to radiation control group. Present findings demonstrate the antigenotoxic potential of ARE against electron beam radiation induced micronuclei formation which may be attributed to scavenging of radiation-induced free radicals

Effectiveness of underground coal extraction. Effektivnost' podzemnoy dobychi uglya

Energy Technology Data Exchange (ETDEWEB)

Pirskiy, A A

1982-01-01

This book examines the possibility of improving the efficiency of underground coal extraction based on the solution to the scientific-technical problem of monitoring and controlling concentration and intensifying mining operations. The problem has been resolved as applied to conditions of working coal fields of the Lvov-Volynskiy basin, West Donbass and other regions which are similar in relation to mining-geological conditions. The main conclusions and recommendations consist of the following: synthesized concept ''concentration of mining operations'' is determined by regulation and concentration, intensification of mining operations by using progressive technology, mechanization and organization of production in order to increase extraction, improve productivity of labor and reduce the net cost of coal. The structure of concentration of mining operations is based on the synthesis of natural, technical and organizational conditions for working coal seams. The problem of monitoring and control of the concentration of mining operations was realized by using the systems method based on the laws of development, principles of comprehensive evaluation and optimization of the level of concentration based on economic-mathematical modeling. The use of the systems approach guarantees a comprehensive solution to the problem. In definite periods of development of the coal industry, between the organizational-technical potentialities, natural conditions and trends determined in the sector for the change in the level of mining operation concentration, disproportions develop. The level of work concentration goes beyond the limits of optimal values, and the effectiveness of coal extraction is reduced. In order to predict and eliminate this phenomenon, it is recommended that the level of mining concentration be controlled.

CMPO, a new extractant for actinides: A review of the currently available literature

Energy Technology Data Exchange (ETDEWEB)

Liansheng, Wei [Institute of Atomic Energy of Beijing (China); Gasparini, G M [ENEA - Dipartimento Ciclo del Combustibile, Centro Ricerche Energia, Casaccia (Italy)

1989-05-15

The extractive properties of dialkyl-N,N-dialkyl carbamoyl methyl phosphinoxides, a series of extractants for liquid-liquid extraction techniques, suitable for actinides separation in any valence state, are described. These extractants have been especially studied to treat effluents contaminated with alpha emitters. The technical reasons because n-octyl(phenyl)-N,N-diisobutyl carbamoyl methyl phosphinoxide (CMPO) and its best experimental conditions have been chosen are examined. CMPO is the extractant utilized to treat the alpha contaminated effluents of the CRE Casaccia Plutonium Laboratory by means of the TESEO Process, studied and verified in our laboratories. (author)

CMPO, a new extractant for actinides: A review of the currently available literature

International Nuclear Information System (INIS)

Wei Liansheng; Gasparini, G.M.

1989-05-01

The extractive properties of dialkyl-N,N-dialkyl carbamoyl methyl phosphinoxides, a series of extractants for liquid-liquid extraction techniques, suitable for actinides separation in any valence state, are described. These extractants have been especially studied to treat effluents contaminated with alpha emitters. The technical reasons because n-octyl(phenyl)-N,N-diisobutyl carbamoyl methyl phosphinoxide (CMPO) and its best experimental conditions have been chosen are examined. CMPO is the extractant utilized to treat the alpha contaminated effluents of the CRE Casaccia Plutonium Laboratory by means of the TESEO Process, studied and verified in our laboratories. (author)

Glycerol extracting dealcoholization for the biodiesel separation process.

Science.gov (United States)

Ye, Jianchu; Sha, Yong; Zhang, Yun; Yuan, Yunlong; Wu, Housheng

2011-04-01

By means of utilizing sunflower oil and Jatropha oil as raw oil respectively, the biodiesel transesterification production and the multi-stage extracting separation were carried out experimentally. Results indicate that dealcoholized crude glycerol can be utilized as the extracting agent to achieve effective separation of methanol from the methyl ester phase, and the glycerol content in the dealcoholized methyl esters is as low as 0.02 wt.%. For the biodiesel separation process utilizing glycerol extracting dealcoholization, its technical and equipment information were acquired through the rigorous process simulation in contrast to the traditional biodiesel distillation separation process, and results show that its energy consumption decrease about 35% in contrast to that of the distillation separation process. The glycerol extracting dealcoholization has sufficient feasibility and superiority for the biodiesel separation process. Copyright © 2011 Elsevier Ltd. All rights reserved.

IMPACT OF COSOLVENT FLUSHING ON SUBSURFACE MICROBIAL ECOLOGY AT THE FORMER SAGE'S DRY CLEANER SITE

Science.gov (United States)

The Solvent Extraction Residual Biotreatment (SERB) technology was evaluated at the former Sage's Dry Cleaner site in Jacksonville, FL where an area of tetrachloroethylene (PCE) contamination was identified. The SERB technology is a treatment train approach to complete site rest...

Coordination of the commissioning of the LHC technical systems

CERN Document Server

Saban, R; Casas Lino, M P; Fernandez Robles, C; Pojer, M; Schmidt, R; Solfaroli Camillocci, M; Vergara Fernandez, A

2008-01-01

The Large Hadron Collider operation relies on 1232 superconducting dipoles with a field of 8.33T and 400 superconducting quadrupoles with a strength of 220 T/m powered at 12kA, operating in superfluid He at 1.9K. For dipoles and quadrupoles as well as for many other magnets more than 1700 power converters are necessary to feed the superconducting circuits. A sophisticated magnet protection system is crucial to detect a quench and safely extract the energy stored in the circuits (about 1GJ only in one of the dipole circuits) after a resistive transition. Besides, in such complex architecture, many technical services (e.g. cooling and ventilation, technical network, electrical distribution, GSM network, controls system, etc.) have to be reliably available during commissioning. Consequently, the commissioning of the technical systems and the associated infrastructures has been carefully studied. Procedures, automatic control and analysis tools, repositories for test data, management structures for carrying out a...

Optical coherence tomography a clinical and technical update

CERN Document Server

Cunha-Vaz, José

2012-01-01

Optical Coherence Tomography represents the ultimate noninvasive  ocular imaging technique although being in the field for over two-decades. This book encompasses both medical and technical developments and recent achievements. Here, the authors cover the field of application from the anterior to the posterior ocular segments (Part I) and present a comprehensive review on the development of OCT. Important developments towards  clinical applications are covered in Part II, ranging from the adaptive optics to the integration on a slit-lamp, and passing through new structural  and functional information extraction from OCT data. The book is intended to be informative, coherent and comprehensive for both the medical and technical communities and aims at easing the communication between the two fields and bridging the gap between the two scientific communities.

Extracting histones for the specific purpose of label-free MS.

Science.gov (United States)

Govaert, Elisabeth; Van Steendam, Katleen; Scheerlinck, Ellen; Vossaert, Liesbeth; Meert, Paulien; Stella, Martina; Willems, Sander; De Clerck, Laura; Dhaenens, Maarten; Deforce, Dieter

2016-12-01

Extracting histones from cells is the first step in studies that aim to characterize histones and their post-translational modifications (hPTMs) with MS. In the last decade, label-free quantification is more frequently being used for MS-based histone characterization. However, many histone extraction protocols were not specifically designed for label-free MS. While label-free quantification has its advantages, it is also very susceptible to technical variation. Here, we adjust an established histone extraction protocol according to general label-free MS guidelines with a specific focus on minimizing sample handling. These protocols are first evaluated using SDS-PAGE. Hereafter, a selection of extraction protocols was used in a complete histone workflow for label-free MS. All protocols display nearly identical relative quantification of hPTMs. We thus show that, depending on the cell type under investigation and at the cost of some additional contaminating proteins, minimizing sample handling can be done during histone isolation. This allows analyzing bigger sample batches, leads to reduced technical variation and minimizes the chance of in vitro alterations to the hPTM snapshot. Overall, these results allow researchers to determine the best protocol depending on the resources and goal of their specific study. Data are available via ProteomeXchange with identifier PXD002885. © 2016 The Authors. Proteomics Published by Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Flexible time domain averaging technique

Science.gov (United States)

Zhao, Ming; Lin, Jing; Lei, Yaguo; Wang, Xiufeng

2013-09-01

Time domain averaging(TDA) is essentially a comb filter, it cannot extract the specified harmonics which may be caused by some faults, such as gear eccentric. Meanwhile, TDA always suffers from period cutting error(PCE) to different extent. Several improved TDA methods have been proposed, however they cannot completely eliminate the waveform reconstruction error caused by PCE. In order to overcome the shortcomings of conventional methods, a flexible time domain averaging(FTDA) technique is established, which adapts to the analyzed signal through adjusting each harmonic of the comb filter. In this technique, the explicit form of FTDA is first constructed by frequency domain sampling. Subsequently, chirp Z-transform(CZT) is employed in the algorithm of FTDA, which can improve the calculating efficiency significantly. Since the signal is reconstructed in the continuous time domain, there is no PCE in the FTDA. To validate the effectiveness of FTDA in the signal de-noising, interpolation and harmonic reconstruction, a simulated multi-components periodic signal that corrupted by noise is processed by FTDA. The simulation results show that the FTDA is capable of recovering the periodic components from the background noise effectively. Moreover, it can improve the signal-to-noise ratio by 7.9 dB compared with conventional ones. Experiments are also carried out on gearbox test rigs with chipped tooth and eccentricity gear, respectively. It is shown that the FTDA can identify the direction and severity of the eccentricity gear, and further enhances the amplitudes of impulses by 35%. The proposed technique not only solves the problem of PCE, but also provides a useful tool for the fault symptom extraction of rotating machinery.

Electrochemical and Chemical Complications Resulting from Yeast Extract Addition to Stimulate Microbial Growth

Science.gov (United States)

2016-09-22

including strains of Saccharomyces cerevisiae grown on molasses-based media, debittered brewers yeasts (strains of Saccharo- myces cerevisiae or...RESPONSIBLE PERSON 19b. TELEPHONE NUMBER (Include area code) Technical Note: Electrochemical and Chemical Complications Resulting from Yeast Extract...Addition to Stimulate Microbial Growth Jason S. Lee‡,* and Brenda J. Little* ABSTRACT Addition of 1 g/L yeast extract (YE) to sterile, aerobic

Analysis of Intracellular Metabolites from Microorganisms: Quenching and Extraction Protocols.

Science.gov (United States)

Pinu, Farhana R; Villas-Boas, Silas G; Aggio, Raphael

2017-10-23

Sample preparation is one of the most important steps in metabolome analysis. The challenges of determining microbial metabolome have been well discussed within the research community and many improvements have already been achieved in last decade. The analysis of intracellular metabolites is particularly challenging. Environmental perturbations may considerably affect microbial metabolism, which results in intracellular metabolites being rapidly degraded or metabolized by enzymatic reactions. Therefore, quenching or the complete stop of cell metabolism is a pre-requisite for accurate intracellular metabolite analysis. After quenching, metabolites need to be extracted from the intracellular compartment. The choice of the most suitable metabolite extraction method/s is another crucial step. The literature indicates that specific classes of metabolites are better extracted by different extraction protocols. In this review, we discuss the technical aspects and advancements of quenching and extraction of intracellular metabolite analysis from microbial cells.

Preliminary study of technical terminology for the retrieval of scientific book metadata records

DEFF Research Database (Denmark)

Larsen, Birger; Lioma, Christina; Frommholz, Ingo

2012-01-01

Books only represented by brief metadata (book records) are particularly hard to retrieve. One way of improving their retrieval is by extracting retrieval enhancing features from them. This work focusses on scientific (physics) book records. We ask if their technical terminology can be used...

Tool-based Risk Assessment of Cloud Infrastructures as Socio-Technical Systems

DEFF Research Database (Denmark)

Nidd, Michael; Ivanova, Marieta Georgieva; Probst, Christian W.

2015-01-01

Assessing risk in cloud infrastructures is difficult. Typical cloud infrastructures contain potentially thousands of nodes that are highly interconnected and dynamic. Another important component is the set of human actors who get access to data and computing infrastructure. The cloud infrastructure...... exercise for cloud infrastructures using the socio-technical model developed in the TRESPASS project; after showing how to model typical components of a cloud infrastructure, we show how attacks are identified on this model and discuss their connection to risk assessment. The technical part of the model...... is extracted automatically from the configuration of the cloud infrastructure, which is especially important for systems so dynamic and complex....

Enhanced Charge Extraction of Li-Doped TiO2 for Efficient Thermal-Evaporated Sb2S3 Thin Film Solar Cells

Science.gov (United States)

Lan, Chunfeng; Luo, Jingting; Lan, Huabin; Fan, Bo; Peng, Huanxin; Zhao, Jun; Sun, Huibin; Zheng, Zhuanghao; Liang, Guangxing; Fan, Ping

2018-01-01

We provided a new method to improve the efficiency of Sb2S3 thin film solar cells. The TiO2 electron transport layers were doped by lithium to improve their charge extraction properties for the thermal-evaporated Sb2S3 solar cells. The Mott-Schottky curves suggested a change of energy band and faster charge transport in the Li-doped TiO2 films. Compared with the undoped TiO2, Li-doped mesoporous TiO2 dramatically improved the photo-voltaic performance of the thermal-evaporated Sb2S3 thin film solar cells, with the average power conversion efficiency (PCE) increasing from 1.79% to 4.03%, as well as the improved open-voltage (Voc), short-circuit current (Jsc) and fill factors. The best device based on Li-doped TiO2 achieved a power conversion efficiency up to 4.42% as well as a Voc of 0.645 V, which are the highest values among the reported thermal-evaporated Sb2S3 solar cells. This study showed that Li-doping on TiO2 can effectively enhance the charge extraction properties of electron transport layers, offering a new strategy to improve the efficiency of Sb2S3-based solar cells. PMID:29495612

Enhanced Charge Extraction of Li-Doped TiO2 for Efficient Thermal-Evaporated Sb2S3 Thin Film Solar Cells

Directory of Open Access Journals (Sweden)

Chunfeng Lan

2018-02-01

Full Text Available We provided a new method to improve the efficiency of Sb2S3 thin film solar cells. The TiO2 electron transport layers were doped by lithium to improve their charge extraction properties for the thermal-evaporated Sb2S3 solar cells. The Mott-Schottky curves suggested a change of energy band and faster charge transport in the Li-doped TiO2 films. Compared with the undoped TiO2, Li-doped mesoporous TiO2 dramatically improved the photo-voltaic performance of the thermal-evaporated Sb2S3 thin film solar cells, with the average power conversion efficiency (PCE increasing from 1.79% to 4.03%, as well as the improved open-voltage (Voc, short-circuit current (Jsc and fill factors. The best device based on Li-doped TiO2 achieved a power conversion efficiency up to 4.42% as well as a Voc of 0.645 V, which are the highest values among the reported thermal-evaporated Sb2S3 solar cells. This study showed that Li-doping on TiO2 can effectively enhance the charge extraction properties of electron transport layers, offering a new strategy to improve the efficiency of Sb2S3-based solar cells.

Microdetermination of lead, cadmium, zinc and tin in biological and related materials by atomic absorption spectrometry after mineralisation and extraction

International Nuclear Information System (INIS)

Boiteau, H.L.; Metayer, C.

1978-01-01

Two technics permitting to determine either lead, cadmium and zinc, or tin in any biological material (blood, urines, organs, alimentary products of animal or vegetable origin) are described. Every operation (mineralisation and extraction) is made in the same tube and technics, conceived in a way to simplify the manipulations and to reduce the more possible the contamination risks are suitable for determination in series. By working on trial samples near 250 mg, the lower determination limits are around 2 ppb for cadmium, 40 ppb for lead and tin and 2 ppm for zinc. The repeatability studies of different technical stages show that mineralisation and extraction only have a weak incidence on the acccuracy of the results [fr

Analysis of Intracellular Metabolites from Microorganisms: Quenching and Extraction Protocols

Directory of Open Access Journals (Sweden)

Farhana R. Pinu

2017-10-01

Full Text Available Sample preparation is one of the most important steps in metabolome analysis. The challenges of determining microbial metabolome have been well discussed within the research community and many improvements have already been achieved in last decade. The analysis of intracellular metabolites is particularly challenging. Environmental perturbations may considerably affect microbial metabolism, which results in intracellular metabolites being rapidly degraded or metabolized by enzymatic reactions. Therefore, quenching or the complete stop of cell metabolism is a pre-requisite for accurate intracellular metabolite analysis. After quenching, metabolites need to be extracted from the intracellular compartment. The choice of the most suitable metabolite extraction method/s is another crucial step. The literature indicates that specific classes of metabolites are better extracted by different extraction protocols. In this review, we discuss the technical aspects and advancements of quenching and extraction of intracellular metabolite analysis from microbial cells.

Patent Keyword Extraction for Sustainable Technology Management

Directory of Open Access Journals (Sweden)

Jongchan Kim

2018-04-01

Full Text Available Recently, sustainable growth and development has become an important issue for governments and corporations. However, maintaining sustainable development is very difficult. These difficulties can be attributed to sociocultural and political backgrounds that change over time [1]. Because of these changes, the technologies for sustainability also change, so governments and companies attempt to predict and manage technology using patent analyses, but it is very difficult to predict the rapidly changing technology markets. The best way to achieve insight into technology management in this rapidly changing market is to build a technology management direction and strategy that is flexible and adaptable to the volatile market environment through continuous monitoring and analysis. Quantitative patent analysis using text mining is an effective method for sustainable technology management. There have been many studies that have used text mining and word-based patent analyses to extract keywords and remove noise words. Because the extracted keywords are considered to have a significant effect on the further analysis, researchers need to carefully check out whether they are valid or not. However, most prior studies assume that the extracted keywords are appropriate, without evaluating their validity. Therefore, the criteria used to extract keywords needs to change. Until now, these criteria have focused on how well a patent can be classified according to its technical characteristics in the collected patent data set, typically using term frequency–inverse document frequency weights that are calculated by comparing the words in patents. However, this is not suitable when analyzing a single patent. Therefore, we need keyword selection criteria and an extraction method capable of representing the technical characteristics of a single patent without comparing them with other patents. In this study, we proposed a methodology to extract valid keywords from

Avaliação técnica e econômica da extração de madeira de eucalipto com"clambunk skidder" Technical and economic evaluation of eucalyptus log extraction using a clambunk skidder

Directory of Open Access Journals (Sweden)

Robson José de Oliveira

2006-04-01

Full Text Available O presente estudo teve como objetivo avaliar técnica e economicamente atividades de extração de madeira em vários declives, utilizando-se um trator florestal arrastador ("clambunk skidder" com rodado de pneus recoberto por esteiras. A avaliação técnica consistiu em determinar os índices de produtividade, e a avaliação econômica baseou-se na determinação dos custos operacionais da máquina. O delineamento experimental foi inteiramente casualizado, no esquema fatorial 3 x 2 x 5 (três níveis de declive, duas classes de produtividade florestal e cinco níveis de distâncias de extração com três repetições. Os resultados demonstraram que os estratos situados em menores declives e distâncias de extração apresentaram maior produtividade em relação àqueles de maiores declives e distâncias de extração. A produtividade do trator florestal arrastador avaliado variou entre 18,34 m³.h-1 e 72,08 m³.h-1, com custo operacional médio de US$90,93 por hora efetiva de trabalho.The objective of this study was to evaluate technical and economic log extraction activities using a clambunk skidder with tracks over the tires. The technical evaluation consisted in determining the log extraction productivity indexes and the economic evaluation was based on operational cost determination. The experimental design was complete randomized, with a 3x2x5 factorial arrangement (three slope levels, two wood productivity classes and five ranks of extraction distance, with three repetitions. In a general way, the results showed that the equipment productivity decreases with the increase of the slope terrain and the extraction distance. Its productivity varied from 18.34 m³.h-1 to 72.08 m³.h-1. The operational cost was US$ 90.93 per effective worked hour.

Modification of back electrode with WO3 layer and its effect on Cu2ZnSn(S,Se)4-based solar cells

Science.gov (United States)

Shi, Kun; Yao, Bin; Li, Yongfeng; Ding, Zhanhui; Deng, Rui; Sui, Yingrui; Zhang, Zhenzhong; Zhao, Haifeng; Zhang, Ligong

2018-01-01

In the present work, we designed and prepared Cu2ZnSn(S,Se)4 (CZTSSe)-based solar cells with a new structure of Al/ITO/ZnO/CdS/CZTSSe/WO3/Mo/SLG (S1-5) by depositing about 5-nm-thick WO3 layer with monoclinic structure on the back electrode Mo/SLG of solar cells with the convention structure of Al/ITO/ZnO/CdS/CZTSSe/Mo/SLG (S2), with the aim of improving the power conversion efficiency (PCE) of CZTSSe-based solar cells. It is found that the average open circuit voltage (Voc) increases from 346.7 mV of the S2 cells to 400.9 mV of the S1-5 cells, the average short circuit current density (Jsc) from 26.4 mA/cm2 to 32.1 mA/cm2 and the filling factor (FF) from 33.8 to 40.0 by addition of the WO3 layer, which results in that the average PCE increases from 3.10% of the S2 cells to 5.14% of the S1-5 cells. The average increasing percent of the PCE is 65.8%. The increase in Voc, Jsc and FF of the S1-5 cells compared to the S2 cells is attributed to that the WO3 layer prevent the Se coming from Se ambient and CZTSSe to react with the Mo to form MoSe2 and other second phases, which makes the shunt resistance (Rsh) of the S1-5 increase and the series resistance (Rs) and reverse saturation current density (J0) decrease compared to the S2 cells. The decreased J0 is main factor of improvement of the PCE. A mechanism of influence of the Rsh, Rs and J0 on the PCE is also revealed. Our result demonstrates that addition of the WO3 layer with a reasonable thickness can be a promising technical route of improving the PCE of the CZTSSe-based solar cell.

INDOT Technical Training Plan : [Technical Summary

Science.gov (United States)

2012-01-01

A wide range of job classifications, increasing technical : performance expectations, licensing and certification requirements, : budget restrictions and frequent department : reorganization has made technical training of employees : more difficult, ...

Survey of subsurface treatment technologies for environmental restoration sites at Sandia National Laboratories, New Mexico.

Energy Technology Data Exchange (ETDEWEB)

McGrath, Lucas K.; Ho, Clifford Kuofei; Wright, Jerome L.

2003-08-01

This report provides a survey of remediation and treatment technologies for contaminants of concern at environmental restoration (ER) sites at Sandia National Laboratories, New Mexico. The sites that were evaluated include the Tijeras Arroyo Groundwater, Technical Area V, and Canyons sites. The primary contaminants of concern at these sites include trichloroethylene (TCE), tetrachloroethylene (PCE), and nitrate in groundwater. Due to the low contaminant concentrations (close to regulatory limits) and significant depths to groundwater ({approx}500 feet) at these sites, few in-situ remediation technologies are applicable. The most applicable treatment technologies include monitored natural attenuation and enhanced bioremediation/denitrification to reduce the concentrations of TCE, PCE, and nitrate in the groundwater. Stripping technologies to remove chlorinated solvents and other volatile organic compounds from the vadose zone can also be implemented, if needed.

Application of Advanced Sensor Technology to DoD Soil Vapor Intrusion Problems

Science.gov (United States)

2012-10-01

Technical material contained in this report has been approved for public release. Mention of trade names or commercial products in this...found in a number of common household products (Agency for Toxic Substances and Disease Registry [ATSDR], 1997; Colorado Department of Public Health and...benzene, TCE, tetrachloroethylene (PCE), ethylbenzene and meta (m)-xylene, as well as several of their response patterns. a) b

Solvent extraction and its practical application for the recovery of copper and uranium

International Nuclear Information System (INIS)

Reuter, J.

1975-01-01

In recent years solvent extraction has been developed to a stage that allows practical application first for the recovery of uranium and later also for winning copper from low-grade acid-soluble ores. By now it has been realized in several plants with great technical and ecomomic success. Solvent extraction includes the following essential operations: leaching, solvent extraction, back extraction of the organically bonded valuable mineral to an acid, aqueous solution and finally separation of the valuable metal from the final acid by precipitation or electrolytic procedures. Upon assessing the cost of the solvent extraction process for the recovery of copper it turns out that from an economic point of view it is significantly superior to the conventional cementation process. (orig.) [de

Platelet-rich plasma: updating of extraction devices

Directory of Open Access Journals (Sweden)

Raquel Moreno

2016-12-01

Full Text Available Propose: To describe PRP extraction devices, through a review of kits available in Spain, taking into account AEMPS and SEFH working groups (GPS, Farmacotecnia, Hemoderivados groups contributions. Methods: Three independent searches about PRP extraction devices were carried out. Device suppliers were contacted and an individually meeting was called with each one. Characteristics of each device was reviewed by virtual demonstration. A kits comparison chart was made with all the information acquired. Kits were classified as Closed-Technique and Opened- Technique in accordance with the AEMPS technical committee report. Results: Ten devices were found: ACP®; Angel®, Cascade®, Endoret ®, GPS®, Magellan®, Minos®, Ortho-pras®, Smart-prepr® and Tricell®. However, we could found out the mechanism in detail of seven of them. Information about Cascade®, Magellan ® and Smart-prepr® kits was not enough. Conclusion: The review provided the main PRP extraction devices available with CE marking and its distinguishing characteristics, however, it is crucial to pay attention to PRP extraction procedure and administration, to guarantee the final product quality. Pharmacy Department must get involved in the device selections due to the close link with the manufactured drug quality. Working together with the AEMPS will contribute to defining extraction procedure specifically.

Evaluation of the genotoxic potential of Mangifera indica L. extract (Vimang), a new natural product with antioxidant activity.

Science.gov (United States)

Rodeiro, I; Cancino, L; González, J E; Morffi, J; Garrido, G; González, R M; Nuñez, A; Delgado, R

2006-10-01

Mangifera indica L. extract (Vimang) consists of a defined mixture of components (polyphenols, terpenoids, steroids, fatty acids and microelements). It contains a variety of polyphenols, phenolic esters, flavan-3-ols and a xanthone (mangiferin), as main component. This extract has antioxidant action, antitumor and immunemodulatory effects proved in experimental models in both in vitro and in vivo assays. The present study was performed to investigate the genotoxicity potential activity of Vimang assessed through different tests: Ames, Comet and micronucleus assays. Positive and negative controls were included in each experimental series. Histidine requiring mutants of Salmonella typhimurium TA1535, TA1537, TA1538, TA98, TA100 and TA102 strains for point-mutation tests and in vitro micronucleus assay in primary human lymphocytes with and without metabolic activation were performed. In addition, genotoxic effects were evaluated on blood peripheral lymphocytes of NMRI mice of both sexes, which were treated during 2 days with intraperitoneal doses of M. indica L. extract (50-150 mg/kg). The observed results permitted to affirm that Vimang (200-5,000 microg/plate) did not increase the frequency of reverse mutations in the Ames test in presence or not of metabolic activation. Results of Comet assay showed that the extract did not induce single strand breaks or alkali-labile sites on blood peripheral lymphocytes of treated animals compared with controls. On the other hand, the results of the micronucleus studies (in vitro and in vivo) showed Vimang induces cytotoxic activity, determined as cell viability or PCE/NCE ratio, but neither increased the frequency of micronucleated binucleate cells in culture of human lymphocytes nor in mice bone marrow cells under our experimental conditions. The positive control chemicals included in each experiment induced the expected changes. The present results indicate that M. indica L. extract showed evidences of light cytotoxic activity

Production of Banana Fiber Yarns for Technical Textile Reinforced Composites

Directory of Open Access Journals (Sweden)

Zaida Ortega

2016-05-01

Full Text Available Natural fibers have been used as an alternative to synthetic ones for their greener character; banana fibers have the advantage of coming from an agricultural residue. Fibers have been extracted by mechanical means from banana tree pseudostems, as a strategy to valorize banana crops residues. To increase the mechanical properties of the composite, technical textiles can be used as reinforcement, instead of short fibers. To do so, fibers must be spun and woven. The aim of this paper is to show the viability of using banana fibers to obtain a yarn suitable to be woven, after an enzymatic treatment, which is more environmentally friendly. Extracted long fibers are cut to 50 mm length and then immersed into an enzymatic bath for their refining. Conditions of enzymatic treatment have been optimized to produce a textile grade of banana fibers, which have then been characterized. The optimum treating conditions were found with the use of Biopectinase K (100% related to fiber weight at 45 °C, pH 4.5 for 6 h, with bath renewal after three hours. The first spinning trials show that these fibers are suitable to be used for the production of yarns. The next step is the weaving process to obtain a technical fabric for composites production.

Technical aspects of the production of dried extract of Maytenus ilicifolia leaves by jet spouted bed drying.

Science.gov (United States)

Cordeiro, Daniel S; Oliveira, Wanderley P

2005-08-11

This work presents an evaluation of the performance of jet spouted bed with inert particles for production of dried extracts of Maytenus ilicifolia leaves. The development of the extraction procedure was carried-out with the aid of three factors and three levels Box-Behnken design. The effects of the extraction variables, temperature (Text); stirring time (theta); and the ratio of the plant to solvent mass (m(p)/m(s)) on the extraction yield were investigated. The drying performance and product properties were evaluated through the measurement of the product size distribution, loss on drying (Up), flavonoid degradation (D) and, process thermal efficiency (eta). These parameters were measured as a function of the inlet temperature of the spouting gas (Tgi), the feed mass flow rate of the concentrated extract relative to mass flow rate of the spouting gas (Ws/Wg), the ratio between the feed flow rate of spouting gas relative to feed flow rate at a minimum spouting condition (Q/Qms) and the static bed height (H0). A powder product with a low degradation of active substances and good physical properties were obtained for selected operating conditions. These results indicate the feasibility of this drying equipment for the production of dried extracts of M. ilicifolia Martius ex Reiss leaves.

Air sparging/high vacuum extraction to remove chlorinated solvents in groundwater and soil

International Nuclear Information System (INIS)

Phelan, J.M.; Gilliat, M.D.

1998-01-01

An air sparging and high vacuum extraction was installed as an alternative to a containment pump and treat system to reduce the long-term remediation schedule. The site is located at the DOE Mound facility in Miamisburg, Ohio, just south of Dayton. The air sparging system consists of 23 wells interspersed between 17 soil vapor extraction wells. The SVE system has extracted about 1,500 lbs of VOCs in five months. The air sparging system operated for about 6 weeks before shutdown due to suspected biochemical fouling. Technical data are presented on the operating characteristics of the system

Extraction of uranium from seawater

International Nuclear Information System (INIS)

Kanno, M.

1977-01-01

The nuclear power generation is thought to be very important in Japan. However, known domestic uranium resources in Japan are very rare. So, extraction of uranium from sea water have been carried out since 1962 at Japan Tobacco and Salt Public Corporation. There are a number of results obtained also by Kyoto University, Shikoku Govenment Industrial Research Institute, Tokyo University and others. In order to investigate the technical and economical feasibility of extraction of uranium and other resources from sea water, a research program was started in fiscal 1975, sponsored by the Ministry of International Trade and Industry with the budget of about $440,000. In this program, the conceptional design of two types of model plants, the ''column type'' and the ''tidal type'' was drawn on the design bases set up with available information. It was found that there has been several problems waiting solution, but there were no technically fatal problems. Adsorption tests were carried out with adsorbents of more than eleven types, including titanium hydroxide, and it was found that titanium hydroxide made by titanyl surphate and urea had the largest adsorption capacity of uranium among them. Elution experiments were performed only with ammonium carbonate and the efficiency at the temperature of 60 0 C showed three times higher than that of 20 0 C. A few long term column operation was conducted, mainly with the adsorbent of granulated titanium hydroxide for 15-60 days. The maximum yield of uranium throughout the adsorption and elution operation was over 20% and macimum concentration of uranium in eluate was 7 ppm

Soil clean up by vapour extraction: parametrical study; Depollution des sols par extraction sous pression reduite: etude de quelques parametres

Energy Technology Data Exchange (ETDEWEB)

Dutheil, C.

2003-05-15

Soil vapour extraction is a treatment process for soils polluted by volatile organic compounds. Its principle relies on the circulation of gaseous flow in soil by the application of a depression of some hundreds milli-bars. A parametrical study has been led on a soil artificially polluted by tri-chloro-ethene. It shows that the gaseous flow rate has a slight influence on pollutants extraction yield. This is due to rate limited mass transfer processes. Soil moisture plays a negative role on treatment efficiency because of the reduction of the porosity available for the gas circulation. Tests have been performed on a soil polluted by a complex mixture of organic pollutants to elaborate a methodology of technical feasibility assessment. This methodology aims at identifying and limiting risks of site rehabilitation failure. Tests results show that soil vapour extraction was inadequate to treat the soil tested in this study because of the strong affinity between a dense organic phase (grease) and chlorinated solvents. (author)

Predictors of employer satisfaction: technical and non-technical skills.

Science.gov (United States)

Danielson, Jared A; Wu, Tsui-Feng; Fales-Williams, Amanda J; Kirk, Ryan A; Preast, Vanessa A

2012-01-01

Employers of 2007-2009 graduates from Iowa State University College of Veterinary Medicine were asked to respond to a survey regarding their overall satisfaction with their new employees as well as their new employees' preparation in several technical and non-technical skill areas. Seventy-five responses contained complete data and were used in the analysis. Four technical skill areas (data collection, data interpretation, planning, and taking action) and five non-technical skill areas (interpersonal skills, ability to deal with legal issues, business skills, making referrals, and problem solving) were identified. All of the skill area subscales listed above had appropriate reliability (Cronbach's alpha>0.70) and were positively and significantly correlated with overall employer satisfaction. Results of two simultaneous regression analyses indicated that of the four technical skill areas, taking action is the most salient predictor of employer satisfaction. Of the five non-technical skill areas, interpersonal skills, business skills, making referrals, and problem solving were the most important skills in predicting employer satisfaction. Hierarchical regression analysis revealed that all technical skills explained 25% of the variation in employer satisfaction; non-technical skills explained an additional 42% of the variation in employer satisfaction.

Nagra technical report 14-02, geological basics - Dossier VII - Usage conflicts

International Nuclear Information System (INIS)

Gautschi, A.; Becker, J.; Traber, D.; Leu, W.

2014-01-01

This dossier is the seventh of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. It discusses possible conflicts with respect to the use of rock strata below or above the proposed host rock layers. Possible usage could include the extraction of salt, coal or other hydrocarbons. Other possible conflicting uses include the mining of stone, ores and minerals as well as the extraction of mineral water and thermal water. The construction of deep boreholes, for example for geothermal probes, could also cause conflicts with any nuclear waste depositories. The storage of natural gas or carbon sequestration, however, is not considered likely

Technical standards in the law of technical safety

International Nuclear Information System (INIS)

Marburger, P.

1985-01-01

Technical standards are of great importance for the closer definition of inexact terms of law, for instance ''generally accepted technical rules'', ''state of the art'', ''state of science and technology'' or similar normative terms, in the law of technical safety. The paper discusses with whom the authority for regulating this sector of law rests, deals with the different ways of how technical standards are used by the law (''anticipated expert opinion'', reference to such standards in law and administration) and points out demands on the procedure of standardization. (orig.) [de

Nanofiltration for concentration of roasted coffee extract: From bench to pilot

Science.gov (United States)

Dat, Lai Quoc; Quyen, Nguyen Thi Ngoc

2017-09-01

This paper focused on the application of nanofiltration (NF) for concentration of the roasted coffee extract in instant coffee processing. Three kinds of NF membranes were screened for separation capacity of total dry solid (TDS), polyphenols (PPs) and caffeine in roasted coffee extract and NF99 membrane showed the good performance for the NF of the extract. The crossflow NF with NF99 membrane at pilot scale was investigated for technical assessment of concentration of roasted coffee extract. Maximum theoretical concentration was estimated as 6.06. Recovery yields of TDS, PPs and caffeine were higher than 70% at 4.4 of concentration factor. The content of TDS in accumulative permeate was lower than 2.0 g/L. The fouling of NF was also solved by the suitable cleaning procedure with recovery index being 97.7%. Results of research indicate that it is feasible to apply NF for concentration of the roasted coffee extract in instant coffee production.

The technical processes of quarrying in the Late Iron Age of Western Iberia

Directory of Open Access Journals (Sweden)

Jesús RODRÍGUEZ HERNÁNDEZ

2013-01-01

Full Text Available This paper reconstructs the technical processes involved in producing the stone works made by the communities of Western Iberia during the Late Iron Age. For this study, we use both archaeological and ethnographic data. We analyze the characteristics of granite, the extraction process in the quarry, the available means of transport, the tools used and the carving process, focusing analysis on the zoomorphic sculptures known as “verracos”. Assessment of these technical aspects is essential for the analysis of the finished products and constitutes a first step in better understanding the status of stonemasons within the protohistoric societies of the Western Iberian Peninsula.

Technique of calculating specific capital investments in the fuel extracting sectors of industry

Energy Technology Data Exchange (ETDEWEB)

Bugrov, V.A.; Filey, I.A.

1980-01-01

An analysis is made of the existing methods of calculating specific capital investments in the fuel extracting sectors of industry. Their shortcomings are shown. It is suggested that specific capital investments for extraction of coal and gas be defined as the ratio of capital investments to the conditional increase in extraction. Coal extraction should take int consideration all the capital investments associated with the input of new facilities, and the maintenance of the attained level of extraction and reconstruction of the enterprise, as well as all the newly introduced facilities both at the new and at the active enterprises associated with an increase in coal extraction and with maintenance of the facilities. The suggested technique completely corresponds to the ''Standard Technique for Developing a Technical-Industrial-Financial Plan,'' which stipulates determination of specific capital investments per unit of introduced facilities with only the difference that it takes into consideration the specific features of the fuel extracting sectors of industry.

Perovskite Solar Cells: Influence of Hole Transporting Materials on Power Conversion Efficiency.

Science.gov (United States)

Ameen, Sadia; Rub, Malik Abdul; Kosa, Samia A; Alamry, Khalid A; Akhtar, M Shaheer; Shin, Hyung-Shik; Seo, Hyung-Kee; Asiri, Abdullah M; Nazeeruddin, Mohammad Khaja

2016-01-08

The recent advances in perovskite solar cells (PSCs) created a tsunami effect in the photovoltaic community. PSCs are newfangled high-performance photovoltaic devices with low cost that are solution processable for large-scale energy production. The power conversion efficiency (PCE) of such devices experienced an unprecedented increase from 3.8 % to a certified value exceeding 20 %, demonstrating exceptional properties of perovskites as solar cell materials. A key advancement in perovskite solar cells, compared with dye-sensitized solar cells, occurred with the replacement of liquid electrolytes with solid-state hole-transporting materials (HTMs) such as 2,2',7,7'-tetrakis-(N,N-di-4-methoxyphenylamino)-9,9'-spirobifluorene (Spiro-OMeTAD), which contributed to enhanced PCE values and improved the cell stability. Following improvements in the perovskite crystallinity to produce a smooth, uniform morphology, the selective and efficient extraction of positive and negative charges in the device dictated the PCE of PSCs. In this Review, we focus mainly on the HTMs responsible for hole transport and extraction in PSCs, which is one of the essential components for efficient devices. Here, we describe the current state-of-the-art in molecular engineering of hole-transporting materials that are used in PSCs and highlight the requisites for market-viability of this technology. Finally, we include an outlook on molecular engineering of new functional HTMs for high efficiency PSCs. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

76 FR 64083 - Reliability Technical Conference; Notice of Technical Conference

Science.gov (United States)

2011-10-17

... Technical Conference; Notice of Technical Conference Take notice that the Federal Energy Regulatory Commission will hold a Technical Conference on Tuesday, November 29, 2011, from 1 p.m. to 5 p.m. and... reliability that were identified in earlier Commission technical conferences. The conference also will discuss...

Automatic Extraction of Urban Built-Up Area Based on Object-Oriented Method and Remote Sensing Data

Science.gov (United States)

Li, L.; Zhou, H.; Wen, Q.; Chen, T.; Guan, F.; Ren, B.; Yu, H.; Wang, Z.

2018-04-01

Built-up area marks the use of city construction land in the different periods of the development, the accurate extraction is the key to the studies of the changes of urban expansion. This paper studies the technology of automatic extraction of urban built-up area based on object-oriented method and remote sensing data, and realizes the automatic extraction of the main built-up area of the city, which saves the manpower cost greatly. First, the extraction of construction land based on object-oriented method, the main technical steps include: (1) Multi-resolution segmentation; (2) Feature Construction and Selection; (3) Information Extraction of Construction Land Based on Rule Set, The characteristic parameters used in the rule set mainly include the mean of the red band (Mean R), Normalized Difference Vegetation Index (NDVI), Ratio of residential index (RRI), Blue band mean (Mean B), Through the combination of the above characteristic parameters, the construction site information can be extracted. Based on the degree of adaptability, distance and area of the object domain, the urban built-up area can be quickly and accurately defined from the construction land information without depending on other data and expert knowledge to achieve the automatic extraction of the urban built-up area. In this paper, Beijing city as an experimental area for the technical methods of the experiment, the results show that: the city built-up area to achieve automatic extraction, boundary accuracy of 2359.65 m to meet the requirements. The automatic extraction of urban built-up area has strong practicality and can be applied to the monitoring of the change of the main built-up area of city.

Teaching Technical Writing - Towards Technical Writing

DEFF Research Database (Denmark)

Kastberg, Peter

2000-01-01

In this paper I will present key aspects of the curriculum for the university degree in technical translation that I have designed for and subsequently implemented at the German Department of the Aarhus School of Business, Denmark. My starting point will be a critical discussion of the norm that ...... of technical writing.......In this paper I will present key aspects of the curriculum for the university degree in technical translation that I have designed for and subsequently implemented at the German Department of the Aarhus School of Business, Denmark. My starting point will be a critical discussion of the norm...... that used to govern what the quality of an LSP text should be as opposed to the standpoint, which I advocate. By way of summing up, I will show how a university curriculum is designed so that - upon graduation - the technical translator could also be methodological quite well suited to take on the challenge...

Report of the technical review team on the Catalytic Extraction Process

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The TRT was impressed with the quality and volume of laboratory and pilot scale development work that had been conducted over the past year. Many of the doubts and questions raised by the TRP on technical details had been examined, either by theoretical calculations or in the pilot facility. Moreover, a more open and forthcoming attitude was evident among the MMT staff who either presented briefings or responded to the Team`s questions. Of special note to DOE, the TRP recognized a year ago that the pilot facility at Fall River was not designed for radioactive pilot tests. However, from the dialogue surrounding the TRP review, it was evident that not much thought had been given to the hazards, concerns, and special requirements incumbent with radioactive operations -- everything from doing pours of hot radioactive metal from a vessel to remote-handling equipment and operations. This year the TRT noticed a significant improvement in this respect.

Report of the technical review team on the Catalytic Extraction Process

International Nuclear Information System (INIS)

1996-03-01

The TRT was impressed with the quality and volume of laboratory and pilot scale development work that had been conducted over the past year. Many of the doubts and questions raised by the TRP on technical details had been examined, either by theoretical calculations or in the pilot facility. Moreover, a more open and forthcoming attitude was evident among the MMT staff who either presented briefings or responded to the Team's questions. Of special note to DOE, the TRP recognized a year ago that the pilot facility at Fall River was not designed for radioactive pilot tests. However, from the dialogue surrounding the TRP review, it was evident that not much thought had been given to the hazards, concerns, and special requirements incumbent with radioactive operations -- everything from doing pours of hot radioactive metal from a vessel to remote-handling equipment and operations. This year the TRT noticed a significant improvement in this respect

Use and Customization of Risk Scores for Predicting Cardiovascular Events Using Electronic Health Record Data.

Science.gov (United States)

Wolfson, Julian; Vock, David M; Bandyopadhyay, Sunayan; Kottke, Thomas; Vazquez-Benitez, Gabriela; Johnson, Paul; Adomavicius, Gediminas; O'Connor, Patrick J

2017-04-24

Clinicians who are using the Framingham Risk Score (FRS) or the American College of Cardiology/American Heart Association Pooled Cohort Equations (PCE) to estimate risk for their patients based on electronic health data (EHD) face 4 questions. (1) Do published risk scores applied to EHD yield accurate estimates of cardiovascular risk? (2) Are FRS risk estimates, which are based on data that are up to 45 years old, valid for a contemporary patient population seeking routine care? (3) Do the PCE make the FRS obsolete? (4) Does refitting the risk score using EHD improve the accuracy of risk estimates? Data were extracted from the EHD of 84 116 adults aged 40 to 79 years who received care at a large healthcare delivery and insurance organization between 2001 and 2011. We assessed calibration and discrimination for 4 risk scores: published versions of FRS and PCE and versions obtained by refitting models using a subset of the available EHD. The published FRS was well calibrated (calibration statistic K=9.1, miscalibration ranging from 0% to 17% across risk groups), but the PCE displayed modest evidence of miscalibration (calibration statistic K=43.7, miscalibration from 9% to 31%). Discrimination was similar in both models (C-index=0.740 for FRS, 0.747 for PCE). Refitting the published models using EHD did not substantially improve calibration or discrimination. We conclude that published cardiovascular risk models can be successfully applied to EHD to estimate cardiovascular risk; the FRS remains valid and is not obsolete; and model refitting does not meaningfully improve the accuracy of risk estimates. © 2017 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley.

In situ bioremediation via horizontal wells

International Nuclear Information System (INIS)

Hazen, T.C.; Looney, B.B.; Enzien, M.; Dougherty, J.M.; Wear, J.; Fliermans, C.B.; Eddy, C.A.

1993-01-01

The test consisted of methane mixed with air into the contaminated aquifer via a horizontal well and extraction from the vadose zone via a parallel horizontal well. This configuration has the advantage of simultaneously stimulating methanotrophic activity in both the groundwater and vadose zone, and inhibiting spread of the contaminant plume. Groundwater was monitored biweekly from 13 wells for a variety of chemical and microbiological parameters. Groundwater from wells in affected areas showed increases in methanotrophs of more than 1 order of magnitude every 2 weeks for several weeks after 1% methane-in-air injection was started. Some wells had increases as much as 7 orders of magnitude. Simultaneous with the increase in methanotrophs was a decrease in water and soil gas concentrations of trichloroethylene (TCE) and tetrachloroethane (PCE). Two wells declined in TCE/PCE concentration in the water by more than 90% to below 2 ppb. All of the wells in the affected zone showed significant decreases in contaminants in less than one month. Chloride concentrations in the water were inversely correlated with TCE/PCE concentration. Four of five vadose zone piezometers declined from concentration as high as 10,000 ppm to less than 5 ppm in less than 6 weeks. The fifth cluster also declined by more than 95%. After only three months on injection, a decline in TCE/PCE in the sediment of more than 30% was also observed, with TCE/PCE being undetectable in most sediments at the end of the 14-month test. Gene probes and direct isolation from the water and sediment revealed that the right types of methanotrophs were being stimulated and that isolates could degrade TCE at a high rate

Technical editing of research reports in biomedical journals.

Science.gov (United States)

Wager, Elizabeth; Middleton, Philippa

2008-10-08

Most journals try to improve their articles by technical editing processes such as proof-reading, editing to conform to 'house styles', grammatical conventions and checking accuracy of cited references. Despite the considerable resources devoted to technical editing, we do not know whether it improves the accessibility of biomedical research findings or the utility of articles. This is an update of a Cochrane methodology review first published in 2003. To assess the effects of technical editing on research reports in peer-reviewed biomedical journals, and to assess the level of accuracy of references to these reports. We searched The Cochrane Library Issue 2, 2007; MEDLINE (last searched July 2006); EMBASE (last searched June 2007) and checked relevant articles for further references. We also searched the Internet and contacted researchers and experts in the field. Prospective or retrospective comparative studies of technical editing processes applied to original research articles in biomedical journals, as well as studies of reference accuracy. Two review authors independently assessed each study against the selection criteria and assessed the methodological quality of each study. One review author extracted the data, and the second review author repeated this. We located 32 studies addressing technical editing and 66 surveys of reference accuracy. Only three of the studies were randomised controlled trials. A 'package' of largely unspecified editorial processes applied between acceptance and publication was associated with improved readability in two studies and improved reporting quality in another two studies, while another study showed mixed results after stricter editorial policies were introduced. More intensive editorial processes were associated with fewer errors in abstracts and references. Providing instructions to authors was associated with improved reporting of ethics requirements in one study and fewer errors in references in two studies, but no

Neutralization principles for the Extraction and Transport of Ion Beams

CERN Document Server

Riege, H

2000-01-01

The strict application of conventional extraction techniques of ion beams from a plasma source is characterized by a natural intensity limit determined by space charge.The extracted current may be enhanced far beyond this limit by neutralizing the space charge of the extracted ions in the first extraction gap of the source with electrons injected from the opposite side. The transverse and longitudinal emittances of a neutralized ion beam, hence its brightness, are preserved. Results of beam compensation experiments, which have been carried out with a laser ion source, are resumed for proposing a general scheme of neutralizing ion sources and their adjacent low-energy beam transport channels with electron beams. Many technical applications of high-mass ion beam neutralization technology may be identified: the enhancement of ion source output for injection into high-intensity, low-and high-energy accelerators, or ion thrusters in space technology, for the neutral beams needed for plasma heating of magnetic conf...

Negative ion beam extraction in ROBIN

International Nuclear Information System (INIS)

Bansal, Gourab; Gahlaut, Agrajit; Soni, Jignesh; Pandya, Kaushal; Parmar, Kanu G.; Pandey, Ravi; Vuppugalla, Mahesh; Prajapati, Bhavesh; Patel, Amee; Mistery, Hiren; Chakraborty, Arun; Bandyopadhyay, Mainak; Singh, Mahendrajit J.; Phukan, Arindam; Yadav, Ratnakar K.; Parmar, Deepak

2013-01-01

Highlights: ► A RF based negative hydrogen ion beam test bed has been set up at IPR, India. ► Ion source has been successfully commissioned and three campaigns of plasma production have been carried out. ► Extraction system (35 kV) has been installed and commissioning has been initiated. Negative ion beam extraction is immediate milestone. -- Abstract: The RF based single driver −ve ion source experiment test bed ROBIN (Replica Of BATMAN like source in INDIA) has been set up at Institute for Plasma Research (IPR), India in a technical collaboration with IPP, Garching, Germany. A hydrogen plasma of density 5 × 10 12 cm −3 is expected in driver region of ROBIN by launching 100 kW RF power into the driver by 1 MHz RF generator. The cesiated source is expected to deliver a hydrogen negative ion beam of 10 A at 35 kV with a current density of 35 mA/cm 2 as observed in BATMAN. In first phase operation of the ROBIN ion source, a hydrogen plasma has been successfully generated (without extraction system) by coupling 80 kW RF input power through a matching network with high power factor (cos θ > 0.8) and different plasma parameters have been measured using Langmuir probes and emission spectroscopy. The plasma density of 2.5 × 10 11 cm −3 has been measured in the extraction region of ROBIN. For negative hydrogen ion beam extraction in second phase operation, extraction system has been assembled and installed with ion source on the vacuum vessel. The source shall be first operated in volume mode for negative ion beam extraction. The commissioning of the source with high voltage power supply has been initiated

78 FR 27963 - Reliability Technical Conference; Notice of Technical Conference

Science.gov (United States)

2013-05-13

... Technical Conference; Notice of Technical Conference Take notice that the Federal Energy Regulatory Commission will hold a Technical Conference on Tuesday, July 9, 2013 from 9:00 a.m. to 5:00 p.m. This... technical support for webcasts and offers the option of listening to the meeting via phone-bridge for a fee...

Enhanced planar perovskite solar cell efficiency and stability using a perovskite/PCBM heterojunction formed in one step.

Science.gov (United States)

Zhou, Long; Chang, Jingjing; Liu, Ziye; Sun, Xu; Lin, Zhenhua; Chen, Dazheng; Zhang, Chunfu; Zhang, Jincheng; Hao, Yue

2018-02-08

Perovskite/PCBM heterojunctions are efficient for fabricating perovskite solar cells with high performance and long-term stability. In this study, an efficient perovskite/PCBM heterojunction was formed via conventional sequential deposition and one-step formation processes. Compared with conventional deposition, the one-step process was more facile, and produced a perovskite thin film of substantially improved quality due to fullerene passivation. Moreover, the resulting perovskite/PCBM heterojunction exhibited more efficient carrier transfer and extraction, and reduced carrier recombination. The perovskite solar cell device based on one-step perovskite/PCBM heterojunction formation exhibited a higher maximum PCE of 17.8% compared with that from the conventional method (13.7%). The device also showed exceptional stability, retaining 83% of initial PCE after 60 days of storage under ambient conditions.

National Alliance for Advanced Biofuels and Bio-Products Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Olivares, Jose A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Baxter, Ivan [US Dept. of Agriculture (USDA)., Washington, DC (United States); Brown, Judith [Univ. of Arizona, Tucson, AZ (United States); Carleton, Michael [Matrix Genetics, Seattle, WA (United States); Cattolico, Rose Anne [Univ. of Washington, Seattle, WA (United States); Taraka, Dale [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Detter, John C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Devarenne, Timothy P. [Texas Agrilife Research, College Station, TX (United States); Dutcher, Susan K. [Washington Univ., St. Louis, MO (United States); Fox, David T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Goodenough, Ursula [Washington Univ., St. Louis, MO (United States); Jaworski, Jan [Donald Danforth Plant Science Center, St. Louis, MO (United States); Kramer, David [Michigan State Univ., East Lansing, MI (United States); Lipton, Mary S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); McCormick, Margaret [Matrix Genetics, Seattle, WA (United States); Merchant, Sabeeha [Univ. of California, Los Angeles, CA (United States); Molnar, Istvan [Univ. of Arizona, Tucson, AZ (United States); Panisko, Ellen A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pellegrini, Matteo [Univ. of California, Los Angeles, CA (United States); Polle, Juergen [City Univ. (CUNY), NY (United States). Brooklyn College; Sabarsky, Martin [Cellana, Inc., San Diego, CA (United States); Sayre, Richard T. [New Mexico Consortium, Los Alamos, NM (United States); Starkenburg,, Shawn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stormo, Gary [Washington Univ., St. Louis, MO (United States); Twary, Scott N. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Unkefer, Clifford J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Unkefer, Pat J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Yuan, Joshua S. [Texas Agrilife Research, College Station, TX (United States); Arnold, Bob [Univ. of Arizona, Tucson, AZ (United States); Bai, Xuemei [Cellana, Inc., San Diego, CA (United States); Boeing, Wiebke [New Mexico State Univ., Las Cruces, NM (United States); Brown, Lois [Texas Agrilife Research, College Station, TX (United States); Gujarathi, Ninad [Reliance Industries Limited, Mumbai (India); Huesemann, Michael [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lammers, Pete [New Mexico State Univ., Las Cruces, NM (United States); Laur, Paul [Eldorado Biofuels, Santa Fe, NM (United States); Khandan, Nirmala [New Mexico State Univ., Las Cruces, NM (United States); Parsons, Ronald [Solix BioSystems, Fort Collins, CO (United States); Samocha, Tzachi [Texas Agrilife Research, College Station, TX (United States); Thomasson, Alex [Texas Agrilife Research, College Station, TX (United States); Unc, Adrian [New Mexico State Univ., Las Cruces, NM (United States); Waller, Pete [Univ. of Arizona, Tucson, AZ (United States); Bonner, James [Clarkson Univ., Potsdam, NY (United States); Coons, Jim [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Fernando, Sandun [Texas Agrilife Research, College Station, TX (United States); Goodall, Brian [Valicor Renewables, Dexter, MI (United States); Kadam, Kiran [Valicor Renewables, Dexter, MI (United States); Lacey, Ronald [Texas Agrilife Research, College Station, TX (United States); Wei, Liu [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Marrone, Babs [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Nikolov, Zivko [Texas Agrilife Research, College Station, TX (United States); Trewyn, Brian [Colorado School of Mines, Golden, CO (United States); Albrecht, Karl [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Capareda, Sergio [Texas Agrilife Research, College Station, TX (United States); Cheny, Scott [Diversified Energy, Gilbert, AZ (United States); Deng, Shuguang [New Mexico State Univ., Las Cruces, NM (United States); Elliott, Douglas [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Cesar, Granda [Terrabon, LLC, Bryan, TX (United States); Hallen, Richard [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lupton, Steven [UOP Honeywell Co, LLC, Des Plaines, IL (United States); Lynch, Sharry [UOP Honeywell Co, LLC, Des Plaines, IL (United States); Marchese, Anthony [Colorado State Univ., Fort Collins, CO (United States); Nieweg, Jennifer [Albemarle Catilin, Ames, IA (United States); Ogden, Kimberly [Univ. of Arizona, Tucson, AZ (United States); Oyler, James [Genifuel, Salt Lake City, UT (United States); Reardon, Ken [Colorado State Univ., Fort Collins, CO (United States); Roberts, William [North Carolina State Univ., Raleigh, NC (United States); Sams, David [Albemarle Catilin, Ames, IA (United States); Schaub, Tanner [New Mexico State Univ., Las Cruces, NM (United States); Silks, Pete [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Archibeque, Shawn [Colorado State Univ., Fort Collins, CO (United States); Foster, James [Texas Agrilife Research, College Station, TX (United States); Gaitlan, Delbert [Texas Agrilife Research, College Station, TX (United States); Lawrence, Addison [Texas Agrilife Research, College Station, TX (United States); Lodge-Ivey, Shanna [New Mexico State Univ., Las Cruces, NM (United States); Wickersham, Tyron [Texas Agrilife Research, College Station, TX (United States); Blowers, Paul [Univ. of Arizona, Tucson, AZ (United States); Davis, Ryan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Downes, C. Meghan [New Mexico State Univ., Las Cruces, NM (United States); Dunlop, Eric [Pan Pacific Technologies Pty. Ltd., Adelaide (Australia); Frank, Edward [Argonne National Lab. (ANL), Argonne, IL (United States); Handler, Robert [Michigan Technological Univ., Houghton, MI (United States); Newby, Deborah [Idaho National Lab. (INL), Idaho Falls, ID (United States); Pienkos, Philip [National Renewable Energy Lab. (NREL), Golden, CO (United States); Richardson, James [Texas Agrilife Research, College Station, TX (United States); Seider, Warren [Univ. of Pennsylvania, Philadelphia, PA (United States); Shonnard, David [Michigan Technological Univ., Houghton, MI (United States); Skaggs, Richard [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-09-30

The main objective of NAABB was to combine science, technology, and engineering expertise from across the nation to break down critical technical barriers to commercialization of algae-based biofuels. The approach was to address technology development across the entire value chain of algal biofuels production, from selection of strains to cultivation, harvesting, extraction, fuel conversion, and agricultural coproduct production. Sustainable practices and financial feasibility assessments ununderscored the approach and drove the technology development.

Spatial abilities and technical skills performance in health care: a systematic review.

Science.gov (United States)

Langlois, Jean; Bellemare, Christian; Toulouse, Josée; Wells, George A

2015-11-01

The aim of this study was to conduct a systematic review and meta-analysis of the relationship between spatial abilities and technical skills performance in health care in beginners and to compare this relationship with those in intermediate and autonomous learners. Search criteria included 'spatial abilities' and 'technical skills'. Keywords related to these criteria were defined. A literature search was conducted to 20 December, 2013 in Scopus (including MEDLINE) and in several databases on EBSCOhost platforms (CINAHL Plus with Full Text, ERIC, Education Source and PsycINFO). Citations were obtained and reviewed by two independent reviewers. Articles related to retained citations were reviewed and a final list of eligible articles was determined. Articles were assessed for quality using the Scottish Intercollegiate Guidelines Network-50 assessment instrument. Data were extracted from articles in a systematic way. Correlations between spatial abilities test scores and technical skills performance were identified. A series of 8289 citations was obtained. Eighty articles were retained and fully reviewed, yielding 36 eligible articles. The systematic review found a tendency for spatial abilities to be negatively correlated with the duration of technical skills and positively correlated with the quality of technical skills performance in beginners and intermediate learners. Pooled correlations of studies were -0.46 (p = 0.03) and -0.38 (95% confidence interval [CI] -0.53 to -0.21) for duration and 0.33 (95% CI 0.20-0.44) and 0.41 (95% CI 0.26-0.54) for quality of technical skills performance in beginners and intermediate learners, respectively. However, correlations between spatial abilities test scores and technical skills performance were not statistically significant in autonomous learners. Spatial abilities are an important factor to consider in selecting and training individuals in technical skills in health care. © 2015 John Wiley & Sons Ltd.

A review on green trend for oil extraction using subcritical water technology and biodiesel production.

Science.gov (United States)

Abdelmoez, Weal; Ashour, Eman; Naguib, Shahenaz M

2015-01-01

It became a global agenda to develop clean alternative fuels which were domestically available, environmentally acceptable and technically feasible. Thus, biodiesel was destined to make a substantial contribution to the future energy demands of the domestic and industrial economies. Utilization of the non edible vegetable oils as raw materials for biodiesel production had been handled frequently for the past few years. The oil content of these seeds could be extracted by different oil extraction methods, such as mechanical extraction, solvent extraction and by subcritical water extraction technology SWT. Among them, SWT represents a new promising green extraction method. Therefore this review covered the current used non edible oil seeds for biodiesel production as well as giving a sharp focus on the efficiency of using the SWT as a promising extraction method. In addition the advantages and the disadvantages of the different biodiesel production techniques would be covered.

Hybrid heterojunction solar cell based on organic-inorganic silicon nanowire array architecture.

Science.gov (United States)

Shen, Xiaojuan; Sun, Baoquan; Liu, Dong; Lee, Shuit-Tong

2011-12-07

Silicon nanowire arrays (SiNWs) on a planar silicon wafer can be fabricated by a simple metal-assisted wet chemical etching method. They can offer an excellent light harvesting capability through light scattering and trapping. In this work, we demonstrated that the organic-inorganic solar cell based on hybrid composites of conjugated molecules and SiNWs on a planar substrate yielded an excellent power conversion efficiency (PCE) of 9.70%. The high efficiency was ascribed to two aspects: one was the improvement of the light absorption by SiNWs structure on the planar components; the other was the enhancement of charge extraction efficiency, resulting from the novel top contact by forming a thin organic layer shell around the individual silicon nanowire. On the contrary, the sole planar junction solar cell only exhibited a PCE of 6.01%, due to the lower light trapping capability and the less hole extraction efficiency. It indicated that both the SiNWs structure and the thin organic layer top contact were critical to achieve a high performance organic/silicon solar cell. © 2011 American Chemical Society

The impact of nontechnical skills on technical performance in surgery: a systematic review.

Science.gov (United States)

Hull, Louise; Arora, Sonal; Aggarwal, Rajesh; Darzi, Ara; Vincent, Charles; Sevdalis, Nick

2012-02-01

Failures in nontechnical and teamwork skills frequently lie at the heart of harm and near-misses in the operating room (OR). The purpose of this systematic review was to assess the impact of nontechnical skills on technical performance in surgery. MEDLINE, EMBASE, PsycINFO databases were searched, and 2,041 articles were identified. After limits were applied, 341 articles were retrieved for evaluation. Of these, 28 articles were accepted for this review. Data were extracted from the articles regarding sample population, study design and setting, measures of nontechnical skills and technical performance, study findings, and limitations. Of the 28 articles that met inclusion criteria, 21 articles assessed the impact of surgeons' nontechnical skills on their technical performance. The evidence suggests that receiving feedback and effectively coping with stressful events in the OR has a beneficial impact on certain aspects of technical performance. Conversely, increased levels of fatigue are associated with detriments to surgical skill. One article assessed the impact of anesthesiologists' nontechnical skills on anesthetic technical performance, finding a strong positive correlation between the 2 skill sets. Finally, 6 articles assessed the impact of multiple nontechnical skills of the entire OR team on surgical performance. A strong relationship between teamwork failure and technical error was empirically demonstrated in these studies. Evidence suggests that certain nontechnical aspects of performance can enhance or, if lacking, contribute to deterioration of surgeons' technical performance. The precise extent of this effect remains to be elucidated. Copyright © 2012 American College of Surgeons. Published by Elsevier Inc. All rights reserved.

76 FR 80553 - Mandatory Reporting of Greenhouse Gases: Technical Revisions to the Petroleum and Natural Gas...

Science.gov (United States)

2011-12-23

... permeability gas, shale gas, coal seam, or other tight reservoir rock. For example, wells producing coal bed... separation means one or more of the following processes: forced extraction of natural gas liquids, sulfur and... Mandatory Reporting of Greenhouse Gases: Technical Revisions to the Petroleum and Natural Gas Systems...

Optimization of RNA Extraction from Rat Pancreatic Tissue

Directory of Open Access Journals (Sweden)

Sanaz Dastgheib

2014-05-01

Full Text Available Background: Optimized RNA extraction from tissues and cell lines consists of four main stages regardless of the method of extraction: 1 homogenizing, 2 effective denaturation of proteins from RNA, 3 inactivation of ribonuclease, and 4 removal of any DNA, protein, and carbohydrate contamination. Isolation of undamaged intact RNA is challenging when the related tissue contains high levels of RNase. Various technical difficulties occur during extraction of RNA from pancreatic tissue due to spontaneous autolysis. Since standard routine protocols yield unacceptable results in pancrease, we have designed a simple method for RNA extraction by comparing different protocols. Methods: We obtained 20-30 mg pancreatic tissues in less than 2 min from 30 rats. Several methods were performed to extract RNA from pancreatic tissue and evaluate its integrity. All methods were performed three times to obtain reproducible results. Results: Immersing pancreatic tissue in RNA-later for 24 h at -80ºC yielded high quality RNA by using the TriPure reagent which was comparable to the commercial RNeasy Micro Kit. The quality of RNA was evaluated by spectrophotometer, electrophoresis and RT-PCR. We separated intact 28S and 18S ribosomal RNA (rRNA when our procedure was compared with the RNeasy Micro Kit. Finally, full length of the actin gene was amplified by RT-PCR. Conclusion: We designed a simple, fast, cost-effective method for complete RNA extraction from the least amount of quantitatively intact pancreatic tissue

Technical Support Essentials Advice to Succeed in Technical Support

CERN Document Server

Sanchez, Andrew

2010-01-01

Technical Support Essentials is a book about the many facets of technical support. It attempts to provide a wide array of topics to serve as points of improvement, discussion, or simply topics that you might want to learn. The topics range from good work habits to the way technical supportgroups establish their own style of work. This book applies theories, models, and concepts synthesized from existing research in other fields-such as management, economics, leadership, and psychology-and connects them to technical support. The goal is to build on the work of others and allow their success to

Relationship between intraoperative non-technical performance and technical events in bariatric surgery.

Science.gov (United States)

Fecso, A B; Kuzulugil, S S; Babaoglu, C; Bener, A B; Grantcharov, T P

2018-03-30

The operating theatre is a unique environment with complex team interactions, where technical and non-technical performance affect patient outcomes. The correlation between technical and non-technical performance, however, remains underinvestigated. The purpose of this study was to explore these interactions in the operating theatre. A prospective single-centre observational study was conducted at a tertiary academic medical centre. One surgeon and three fellows participated as main operators. All patients who underwent a laparoscopic Roux-en-Y gastric bypass and had the procedures captured using the Operating Room Black Box ® platform were included. Technical assessment was performed using the Objective Structured Assessment of Technical Skills and Generic Error Rating Tool instruments. For non-technical assessment, the Non-Technical Skills for Surgeons (NOTSS) and Scrub Practitioners' List of Intraoperative Non-Technical Skills (SPLINTS) tools were used. Spearman rank-order correlation and N-gram statistics were conducted. Fifty-six patients were included in the study and 90 procedural steps (gastrojejunostomy and jejunojejunostomy) were analysed. There was a moderate to strong correlation between technical adverse events (r s  = 0·417-0·687), rectifications (r s  = 0·380-0·768) and non-technical performance of the surgical and nursing teams (NOTSS and SPLINTS). N-gram statistics showed that after technical errors, events and prior rectifications, the staff surgeon and the scrub nurse exhibited the most positive non-technical behaviours, irrespective of operator (staff surgeon or fellow). This study demonstrated that technical and non-technical performances are related, on both an individual and a team level. Valuable data can be obtained around intraoperative errors, events and rectifications. © 2018 BJS Society Ltd Published by John Wiley & Sons Ltd.

Technical study report on fuel fabrication system

International Nuclear Information System (INIS)

Kono, Shusaku; Tanaka, Kenya; Ono, Kiyoshi; Iwasa, Katsuyoshi; Hoshino, Yasushi; Shinkai, Yasuo

2000-07-01

The feasibility study of FBR and related fuel cycle is performed for developing the FBR recycle system which ensures safety, economic competitiveness, efficient utilization of resources, reduction of environmental burden and enhancement of nuclear non-proliferation under consistency of FBR reactor and fuel cycle systems. In this study, a conceptual design study and system characteristics evaluation are conducted for fuel fabrication systems of pellet process, vibropack process for oxide and nitride fuel and casting process for metal fuel. Technical issues in each process are also extracted. In 1999 fiscal year, a conceptual design study were conducted for the fuel fabrication plants adopting (1) the short pellet process which simplifies the conventional MOX pellet fabrication processes, (2) vibropack processes of aqueous gelation process, improved RIAR process, improved ANL process and fluoride volatility process, (3) casting processes of injection process, centrifuging process. As a result, attainable perspective was obtained for each fuel fabrication system through the evaluation of apparatuses, layout and facility volume, etc. In each fuel fabrication system, technical issues for practical use were made clear. Hereafter, more detailed study will be performed for each system, and research programs for phase II study will be planned. (author)

Imagining Technicities

DEFF Research Database (Denmark)

Liboriussen, Bjarke; Plesner, Ursula

2011-01-01

to the elements of taste and skill. In the final analysis those references were synthesized as five imagined technicities: the architect, the engineer, the client, the Chinese, and the Virtual World native. Because technicities are often assumed and rarely discussed as actants who influence practice, their role......, this article focuses on innovative uses of virtual worlds in architecture. We interviewed architects, industrial designers and other practitioners. Conceptually supported by an understanding of technicity found in Cultural Studies, the interviews were then coded with a focus on interviewees’ references...... in cooperation and development of ICTs seems to pass unnoticed. However, since they are aligned into ICTs, technicities impact innovation....

A novel technique of percutaneous stone extraction in choledocholithiasis after cholecystostomy.

Science.gov (United States)

Lim, Kyoung Hoon; Kim, Yong Joo

2013-05-01

To evaluate the technical feasibility and clinical efficacy of percutaneous common bile duct stone extraction via cystic duct after percutaneous cholecystostomy. Twenty-five consecutive patients with choledocholithiasis underwent percutaneous stone extraction under conscious sedation. The stones were extracted through the 12-Fr sheath using Wittich nitinol stone basket under fluoroscopic guidance via cystic duct after percutaneous trnas-hepatic cholecystostomy. Common bile duct stones were successfully removed in 22 of the 25 patients (88%) by this new technique. The causes of failure in three patients were bile leakage, hematoma of the gallbladder and failure of cystic duct cannulation. Cystic duct injury during this procedure did not occur and there was no post-procedure mortality. The mean period of indwelling catheter was 8.7±4.6 days and the mean duration of hospitalization was 13.4±5.9 days. Percutaneous commmon bile duct stone extraction via the cystic duct through percutaneous cholecystostomy route is effective and feasible for treating choledocholithiasis.

Technical Training: Technical Training Seminar

CERN Multimedia

2004-01-01

Tuesday 30 March TECHNICAL TRAINING SEMINAR From 9:00 to 12:00 and from 13:00 to 16:00 hrs - Council Chamber, Salle B, Salle des Pas Perdus National Instruments (NI) on Tour 2004 Claudia Jüngel, Evrem Yarkin, Joel Clerc, Hervé Baour / NATIONAL INSTRUMENTS The special event NI on Tour 2004, run in Germany, Austria and Switzerland, will be at CERN on March 30. Technical seminars and free introductory courses will be offered all day long in the Council Chamber, Salle B, and Salle des Pas Perdus (buildings 61 and 503). Technical conferences: 09:00 - 12:00 Data acquisition systems on PCs. Industrial measurement and control techniques. 13:00 - 16:00 Advanced LabVIEW software and PXI instrumentation. Measuring instruments and system components for teststand automation. Introductory courses: 09:00 - 12:00 DIAdem: Data analysis and presentation 13:00 - 16:00 Data acquisition with LabVIEW Language: English and French Free special seminar. Registration is recommended with National Instruments Switzerland (please sp...

Technical Training: Technical Training Seminar

CERN Multimedia

2004-01-01

Tuesday 30 March TECHNICAL TRAINING SEMINAR From 9:00 to 12:00 and from 13:00 to 16:00 hrs - Council Chamber, Salle B, Salle des Pas Perdus National Instruments (NI) on Tour 2004 Claudia Jüngel, Evrem Yarkin, Joel Clerc, Hervé Baour / NATIONAL INSTRUMENTS The special event NI on Tour 2004, run in Germany, Austria and Switzerland, will be at CERN on March 30. Technical seminars and free introductory courses will be offered all day long in the Council Chamber, Salle B, and Salle des Pas Perdus (buildings 61 and 503). Technical conferences: 09:00 - 12:00 Data acquisition systems on PCs. Industrial measurement and control techniques. 13:00 - 16:00 Advanced LabVIEW software and PXI instrumentation. Measuring instruments and system components for teststand automation. Introductory courses: 09:00 - 12:00 DIAdem: Data analysis and presentation 13:00 - 16:00 Data acquisition with LabVIEW Language: English and French Free special seminar. Registration is recommended with National Instruments Swi...

Technical Training: Technical Training Seminar

CERN Multimedia

2004-01-01

TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch Monday 9 February 2004 From 10:00 to 12:00 - IT Auditorium - bldg. 31, 3rd floor ANSOFT High-Frequency Seminar David Prestaux, Application Engineer, ANSOFT F-78535 BUC, France This Technical Training seminar will present two Ansoft application products: Ansoft HFSS and Ansoft Designer. Ansoft HFSS makes use of the Finite Element Method (FEM) to calculate field solutions from first principles. It can accurately predict all high-frequency behaviours such as dispersion, mode conversion, and losses due to materials and radiation. Ansoft Designer is a suite of design tools to fully integrate high-frequency, physics-based electromagnetic simulations into a seamless system-level simulation environment. Ansoft Designer uses a simple interface to give complete control over every design task, by a method allowing multiple solvers, Solver on Demand. • Introduction • Overview of the Ansoft Total solution • Ansoft HFSS 9...

A Stochastic Slow Extraction Scheme For U70 Synchrotron

CERN Document Server

Ivanov, S

2004-01-01

Outcomes of a feasibility study for a low-budget sto-chastic slow extraction system in the U70 proton synchro-tron of IHEP are reported. The existing 200 MHz (spill) RF system is to be employed as a longitudinal kicker. It will be driven by a sum of a non-random RF carrier plus an additive random amplitude-modulated signal - either quadrature or in-phase, or both. A few novel solutions to be implemented in the longitudinal diffusion technique that would force protons into the conventional 3-rd order transverse extraction resonance are foreseen so as to com-ply with the technical constraints inherent in U70. Getting a-few-seconds-long and high-quality spills is assessed as being viable with the system in question.

Role of ultrathin metal fluoride layer in organic photovoltaic cells: mechanism of efficiency and lifetime enhancement.

Science.gov (United States)

Lim, Kyung-Geun; Choi, Mi-Ri; Kim, Ji-Hoon; Kim, Dong Hun; Jung, Gwan Ho; Park, Yongsup; Lee, Jong-Lam; Lee, Tae-Woo

2014-04-01

Although rapid progress has been made recently in bulk heterojunction organic solar cells, systematic studies on an ultrathin interfacial layer at the electron extraction contact have not been conducted in detail, which is important to improve both the device efficiency and the lifetime. We find that an ultrathin BaF2 layer at the electron extraction contact strongly influences the open-circuit voltage (Voc ) as the nanomorphology evolves with increasing BaF2 thickness. A vacuum-deposited ultrathin BaF2 layer grows by island growth, so BaF2 layers with a nominal thickness less than that of single-coverage layer (≈3 nm) partially cover the polymeric photoactive layer. As the nominal thickness of the BaF2 layer increased to that of a single-coverage layer, the Voc and power conversion efficiency (PCE) of the organic photovoltaic cells (OPVs) increased but the short-circuit current remained almost constant. The fill factor and the PCE decreased abruptly as the thickness of the BaF2 layer exceeded that of a single-coverage layer, which was ascribed to the insulating nature of BaF2 . We find the major cause of the increased Voc observed in these devices is the lowered work function of the cathode caused by the reaction and release of Ba from thin BaF2 films upon deposition of Al. The OPV device with the BaF2 layer showed a slightly improved maximum PCE (4.0 %) and a greatly (approximately nine times) increased device half-life under continuous simulated solar irradiation at 100 mW cm(-2) as compared with the OPV without an interfacial layer (PCE=2.1 %). We found that the photodegradation of the photoactive layer was not a major cause of the OPV degradation. The hugely improved lifetime with cathode interface modification suggests a significant role of the cathode interfacial layer that can help to prolong device lifetimes. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Risk-based economic decision analysis of remediation options at a PCE-contaminated site

DEFF Research Database (Denmark)

Lemming, Gitte; Friis-Hansen, P.; Bjerg, Poul Løgstrup

2010-01-01

by the remediation activities. More attention is increasingly being given to these secondary environmental impacts when evaluating remediation options. This paper presents a methodology for an integrated economic decision analysis which combines assessments of remediation costs, health risk costs and potential...... at a downstream groundwater well. Potential environmental impacts on the local, regional and global scales due to the site remediation activities are evaluated using life cycle assessments (LCA). The potential impacts on health and environment are converted to monetary units using a simplified cost model. A case......Remediation methods for contaminated sites cover a wide range of technical solutions with different remedial efficiencies and costs. Additionally, they may vary in their secondary impacts on the environment i.e. the potential impacts generated due to emissions and resource use caused...

Shale oil and gas: technical and environmental files

International Nuclear Information System (INIS)

Schilansky, Jean-Louis; Quehen, Audrey; Appert, Olivier; Aurengo, Andre; Candel, Sebastien; Chanin, Marie-Lise; Geoffron, Patrice; Goffe, Bruno; Marsily, Ghislain de; Pouzet, Andre; Schnapper, Dominique; Tardieu, Bernard

2016-01-01

This publication proposes information regarding technical and environmental issues related to shale oil and gas extraction and exploitation. It addresses various topics: hydraulic fracturing (techniques, quantity assessment, regulation), water consumption and management (problematic, quantity assessment, regulation), additives and management of production fluids (a necessary taking into account, quantity assessment, regulation), surface aquifers (surface sheets and exploration activity, quantity assessment, regulation), activity footprint (ground footprint and impact on landscape, quantity assessment, regulation), end of activity and site future (return to the initial condition, quantity assessment, regulation), seismicity (manageable seismic risks, quantity assessment, regulations), greenhouse gas emissions (development, quantity assessment, regulation), issues related to health aspects (general and specific risks, epidemiological studies)

Adaptive Long-Term Monitoring at Environmental Restoration Sites (ER-0629)

Science.gov (United States)

2009-05-01

Printed on recycled paper TECHNICAL REPORT TR-2317-ENV ADAPTIVE LONG-TERM MONITORING AT ENVIRONMENTAL RESTORATION SITES (ER-0629...nondetect values. One curiosity is that the typical recent RL for TCE has been 0.5, whereas that for PCE has been 1.4. As a consequence, and due to...Spring 2000 makes little difference, however. A curiosity is that the anomalous value from Spring 2006 is actually quite similar to the early

Development of a behavioural marker system for scrub practitioners' non-technical skills (SPLINTS system).

Science.gov (United States)

Mitchell, Lucy; Flin, Rhona; Yule, Steven; Mitchell, Janet; Coutts, Kathy; Youngson, George

2013-04-01

Adverse events still occur despite ongoing efforts to reduce harm to patients. Contributory factors to adverse events are often due to limitations in clinicians' non-technical skills (e.g. communication, situation awareness), rather than deficiencies in technical competence. We developed a behavioural rating system to provide a structured means for teaching and assessing scrub practitioners' (i.e. nurse, technician, operating department practitioner) non-technical skills. Psychologists facilitated focus groups (n = 4) with experienced scrub practitioners (n = 16; 4 in each group) to develop a preliminary taxonomy. Focus groups reviewed lists of non-technical-skill-related behaviours that were extracted from an interview study. The focus groups labelled skill categories and elements and also provided examples of good and poor behaviours for those skills. An expert panel (n = 2 psychologists; n = 1 expert nurse) then used an iterative process to individually and collaboratively review and refine those data to produce a prototype skills taxonomy. A preliminary taxonomy containing eight non-technical skill categories with 28 underlying elements was produced. The expert panel reduced this to three categories (situation awareness, communication and teamwork, task management), each with three underlying elements. The system was called the Scrub Practitioners' List of Intraoperative Non-Technical Skills system. A scoring system and a user handbook were also developed. A prototype behavioural rating system for scrub practitioners' non-technical skills was developed, to aid in teaching and providing formative assessment. This important aspect of performance is not currently explicitly addressed in any educational route to qualify as a scrub practitioner. © 2012 Blackwell Publishing Ltd.

Leadless pacemaker extraction from a single-center perspective.

Science.gov (United States)

González Villegas, Elkin; Al Razzo, Omar; Silvestre García, Jorge; Mesa García, José

2018-02-01

Leadless pacemaker can be considered as a technical revolution in cardiac pacing devices, with clear advantages over conventional pacemakers in overcoming all lead-related complications. However, the management of these devices once they reach the end of life (EOL) of the battery is still controversial. In the next years, there will be an increase in the need to define a clear strategy in the management of leadless PM once they reach their EOL. Safe extraction of these devices will define in a great manner this strategy METHODS: We performed the extraction of three functioning Nanostim leadless pacemaker prophylactically in two females and one male patients as part of the Nanostim battery depletion field action recommendation. All patients had a prior transesophageal 3D echocardiography to determine the device intracardiac mobility and the extent of possible endothelialization. For the extractions, we used the Nanostim Retrieval Catheter S1RSIN (St. Jude Medical, St. Paul, MN, USA), which is a proprietary catheter provided by the manufacturing company based on a lasso. Complete extraction of the devices was achieved in all patients using a relatively short fluoroscopic time (16, 19, and 12 minutes). The extraction of leadless pacemakers can be considered as a safe and feasible procedure using the tools provided by the manufacturer and designed for the extraction. However, a very low threshold must be maintained to avoid any risk to the patients. Our extraction time ranges are between 983 and 1,070 days, nevertheless it is necessary to gather more long-term data to assess the feasibility and safety of these procedures. © 2017 Wiley Periodicals, Inc.

Thinking ahead of the surgeon. An interview study to identify scrub nurses' non-technical skills.

Science.gov (United States)

Mitchell, Lucy; Flin, Rhona; Yule, Steven; Mitchell, Janet; Coutts, Kathy; Youngson, George

2011-07-01

Efforts to reduce adverse event rates in healthcare have revealed the importance of identifying the essential non-technical (cognitive and social) skills for safe and effective performance. Previous research on non-technical skills for operating theatre staff has concentrated on doctors rather than nursing professionals. The aim of the study was to identify the critical non-technical skills that are essential for safe and effective performance as an operating theatre scrub nurse. Experienced scrub nurses (n = 25) and consultant surgeons (n = 9) from four Scottish hospitals were interviewed using a semi-structured format. The protocols were designed to identify the main social and cognitive skills required by scrub nurses. Interviews were digitally recorded, transcribed verbatim and independently coded to extract behaviours in order to produce a list of the main non-technical skills for safe and effective scrub nurse performance. The non-technical skills of situation awareness, communication, teamwork, task management and coping with stress were identified as key to successful scrub nurse task performance. Component sets of behaviours for each of these categories were also noted. The interviews with subject matter experts from scrub nursing and surgery produced preliminary evidence that situation awareness, communication, teamwork and coping with stress are the principal non-technical skills required for effective performance as a scrub nurse. Copyright © 2010 Elsevier Ltd. All rights reserved.

Automating the Extraction of Metadata from Archaeological Data Using iRods Rules

Directory of Open Access Journals (Sweden)

David Walling

2011-10-01

Full Text Available The Texas Advanced Computing Center and the Institute for Classical Archaeology at the University of Texas at Austin developed a method that uses iRods rules and a Jython script to automate the extraction of metadata from digital archaeological data. The first step was to create a record-keeping system to classify the data. The record-keeping system employs file and directory hierarchy naming conventions designed specifically to maintain the relationship between the data objects and map the archaeological documentation process. The metadata implicit in the record-keeping system is automatically extracted upon ingest, combined with additional sources of metadata, and stored alongside the data in the iRods preservation environment. This method enables a more organized workflow for the researchers, helps them archive their data close to the moment of data creation, and avoids error prone manual metadata input. We describe the types of metadata extracted and provide technical details of the extraction process and storage of the data and metadata.

Technical innovation and management

Energy Technology Data Exchange (ETDEWEB)

Yoon, Yang Cheol

1982-08-15

This book gives explanations of the conception of technical innovation, development plan in Korea, connection between technology and a growth factor in national income, problem of technical innovation in developing country, analysis on cooperation between a developed country and a developing country, evaluation and strategy of technical development in Korea, technical innovation of industry, management of technical industry, analysis of special condition in Korea.

Technical innovation and management

International Nuclear Information System (INIS)

Yoon, Yang Cheol

1982-08-01

This book gives explanations of the conception of technical innovation, development plan in Korea, connection between technology and a growth factor in national income, problem of technical innovation in developing country, analysis on cooperation between a developed country and a developing country, evaluation and strategy of technical development in Korea, technical innovation of industry, management of technical industry, analysis of special condition in Korea.

Manhattan Project Technical Series The Chemistry of Uranium (I) Chapters 1-10

International Nuclear Information System (INIS)

Rabinowitch, E. I.; Katz, J. J.

1946-01-01

This constitutes Chapters 1 through 10. inclusive, of The Survey Volume on Uranium Chemistry prepared for the Manhattan Project Technical Series. Chapters are titled: Nuclear Properties of Uranium; Properties of the Uranium Atom; Uranium in Nature; Extraction of Uranium from Ores and Preparation of Uranium Metal; Physical Properties of Uranium Metal; Chemical Properties of Uranium Metal; Intermetallic Compounds and Alloy systems of Uranium; the Uranium-Hydrogen System; Uranium Borides, Carbides, and Silicides; Uranium Nitrides, Phosphides, Arsenides, and Antimonides.

Evaluating variation in human gut microbiota profiles due to DNA extraction method and inter-subject differences.

Science.gov (United States)

Wagner Mackenzie, Brett; Waite, David W; Taylor, Michael W

2015-01-01

The human gut contains dense and diverse microbial communities which have profound influences on human health. Gaining meaningful insights into these communities requires provision of high quality microbial nucleic acids from human fecal samples, as well as an understanding of the sources of variation and their impacts on the experimental model. We present here a systematic analysis of commonly used microbial DNA extraction methods, and identify significant sources of variation. Five extraction methods (Human Microbiome Project protocol, MoBio PowerSoil DNA Isolation Kit, QIAamp DNA Stool Mini Kit, ZR Fecal DNA MiniPrep, phenol:chloroform-based DNA isolation) were evaluated based on the following criteria: DNA yield, quality and integrity, and microbial community structure based on Illumina amplicon sequencing of the V4 region of bacterial and archaeal 16S rRNA genes. Our results indicate that the largest portion of variation within the model was attributed to differences between subjects (biological variation), with a smaller proportion of variation associated with DNA extraction method (technical variation) and intra-subject variation. A comprehensive understanding of the potential impact of technical variation on the human gut microbiota will help limit preventable bias, enabling more accurate diversity estimates.

Evaluating variation in human gut microbiota profiles due to DNA extraction method and inter-subject differences

Directory of Open Access Journals (Sweden)

Brett eWagner Mackenzie

2015-02-01

Full Text Available The human gut contains dense and diverse microbial communities which have profound influences on human health. Gaining meaningful insights into these communities requires provision of high quality microbial nucleic acids from human fecal samples, as well as an understanding of the sources of variation and their impacts on the experimental model. We present here a systematic analysis of commonly used microbial DNA extraction methods, and identify significant sources of variation. Five extraction methods (Human Microbiome Project protocol, MoBio PowerSoil DNA Isolation Kit, QIAamp DNA Stool Mini Kit, ZR Fecal DNA MiniPrep, phenol:chloroform-based DNA isolation were evaluated based on the following criteria: DNA yield, quality and integrity, and microbial community structure based on Illumina amplicon sequencing of the V4 region of bacterial and archaeal 16S rRNA genes. Our results indicate that the largest portion of variation within the model was attributed to differences between subjects (biological variation, with a smaller proportion of variation associated with DNA extraction method (technical variation and intra-subject variation. A comprehensive understanding of the potential impact of technical variation on the human gut microbiota will help limit preventable bias, enabling more accurate diversity estimates.

Involvement of Three Esterase Genes from Panonychus citri (McGregor in Fenpropathrin Resistance

Directory of Open Access Journals (Sweden)

Xiao-Min Shen

2016-08-01

Full Text Available The citrus red mite, Panonychus citri (McGregor, is a major citrus pest with a worldwide distribution and an extensive record of pesticide resistance. However, the underlying molecular mechanism associated with fenpropathrin resistance in this species have not yet been reported. In this study, synergist triphenyl phosphate (TPP dramatically increased the toxicity of fenpropathrin, suggesting involvement of carboxylesterases (CarEs in the metabolic detoxification of this insecticide. The subsequent spatiotemporal expression pattern analysis of PcE1, PcE7 and PcE9 showed that three CarEs genes were all over-expressed after insecticide exposure and higher transcripts levels were observed in different field resistant strains of P. citri. Heterologous expression combined with 3-(4,5-dimethyl-thiazol-2-yl-2,5-diphenyltetra-zolium bromide (MTT cytotoxicity assay in Spodoptera frugiperda (Sf9 cells revealed that PcE1-, PcE7- or PcE9-expressing cells showed significantly higher cytoprotective capability than parental Sf9 cells against fenpropathrin, demonstrating that PcEs probably detoxify fenpropathrin. Moreover, gene silencing through the method of leaf-mediated dsRNA feeding followed by insecticide bioassay increased the mortalities of fenpropathrin-treated mites by 31% (PcE1, 27% (PcE7 and 22% (PcE9, respectively, after individual PcE gene dsRNA treatment. In conclusion, this study provides evidence that PcE1, PcE7 and PcE9 are functional genes mediated in fenpropathrin resistance in P. citri and enrich molecular understanding of CarEs during the resistance development of the mite.

Pharmacological Cognitive Enhancement in Healthy Individuals: A Compensation for Cognitive Deficits or a Question of Personality?

Directory of Open Access Journals (Sweden)

Larissa J Maier

Full Text Available The ongoing bioethical debate on pharmacological cognitive enhancement (PCE in healthy individuals is often legitimated by the assumption that PCE will widely spread and become desirable for the general public in the near future. This assumption was questioned as PCE is not equally save and effective in everyone. Additionally, it was supposed that the willingness to use PCE is strongly personality-dependent likely preventing a broad PCE epidemic. Thus, we investigated whether the cognitive performance and personality of healthy individuals with regular nonmedical methylphenidate (MPH use for PCE differ from stimulant-naïve controls. Twenty-five healthy individuals using MPH for PCE were compared with 39 age-, sex-, and education-matched healthy controls regarding cognitive performance and personality assessed by a comprehensive neuropsychological test battery including social cognition, prosocial behavior, decision-making, impulsivity, and personality questionnaires. Substance use was assessed through self-report in an interview and quantitative hair and urine analyses. Recently abstinent PCE users showed no cognitive impairment but superior strategic thinking and decision-making. Furthermore, PCE users displayed higher levels of trait impulsivity, novelty seeking, and Machiavellianism combined with lower levels of social reward dependence and cognitive empathy. Finally, PCE users reported a smaller social network and exhibited less prosocial behavior in social interaction tasks. In conclusion, the assumption that PCE use will soon become epidemic is not supported by the present findings as PCE users showed a highly specific personality profile that shares a number of features with illegal stimulant users. Lastly, regular MPH use for PCE is not necessarily associated with cognitive deficits.

Bidentate organophosphorus extractants: purification, properties and applications to removal of actinides from acidic waste solutions

International Nuclear Information System (INIS)

Schulz, W.W.; McIsaac, L.D.

1977-05-01

At both Hanford and Idaho, DHDECMP (dihexyl-N, N-diethylcarbamylmethylene phosphonate) continuous counter-current solvent extraction processes are being developed for removal of americium, plutonium, and, in some cases, other actinides from acidic wastes generated at these locations. Bench and, eventually, pilot and plant-scale testing and application of these processes have been substantially enhanced by the discovery of suitable chemical and physical methods of removing deleterious impurities from technical-grade DHDECMP. Flowsheet details, as well as various properties of purified DHDECMP extractants, are enumerated

Application of data-processing to the technical and economical management of the plants of Simo

International Nuclear Information System (INIS)

Chastagner, F.

1988-01-01

The firm Simo is entrusted with the processing of the uranium ores extracted from the mines of Cogema in France, in its three plants. The paper describes the conception and the functioning of the information system. Among the advantages contributed by the system, the coherence between the technical follow-up and the economical follow-up constitutes one of the principal progressive features [fr

Comparable efficiency of different extraction protocols for wheat and rye prolamins

Directory of Open Access Journals (Sweden)

Peter Socha

2016-01-01

Full Text Available The identification and quantification of cereal storage proteins is of interest of many researchers. Their structural or functional properties are usually affected by the way how they are extracted. The efficiency of extraction process depends on the cereal source and working conditions. Here, we described various commonly used extraction protocols differing in the extraction conditions (pre-extraction of albumins/globulins, sequential extraction of individual protein fractions or co-extraction of gluten proteins, heating or non-heating, reducing or non-reducing conditions. The total protein content of all fractions extracted from commercially available wheat and rye flours was measured by the Bradford method. Tris-Tricine SDS-PAGE was used to determine the molecular weights of wheat gliadins, rye secalins and high-molecular weight glutelins which are the main triggering factors causing celiac disease. Moreover, we were able to distinguish individual subunits (α/β-, γ-, ω-gliadins and 40k-γ-, 75k-γ-, ω-secalins of wheat/rye prolamins. Generally, modified extraction protocols against classical Osborne procedure were more effective and yields higher protein content in all protein fractions. Bradford measurement led into underestimation of results in three extraction procedures, while all protein fractions were clearly identified on SDS-PAGE gels. Co-extraction of gluten proteins resulted in appearance of both, low-molecular weight fractions (wheat gliadins and rye secalins as well as high-molecular weight glutelins which means that is not necessary to extract gluten proteins separately. The two of three extraction protocols showed high technical reproducibility with coefficient of variation less than 20%. Carefully optimized extraction protocol can be advantageous for further analyses of cereal prolamins.  Normal 0 21 false false false SK X-NONE X-NONE

Uranium extraction technology

International Nuclear Information System (INIS)

1993-01-01

In 1983 the Nuclear Energy Agency of the Organisation for Economic Co-operation and Development (OECD/NEA) and the IAEA jointly published a book on Uranium Extraction Technology. A primary objective of this report was to document the significant technological developments that took place during the 1970s. The purpose of this present publication is to update and expand the original book. It includes background information about the principle of the unit operations used in uranium ore processing and summarizes the current state of the art. The publication also seeks to preserve the technology and the operating 'know-how' developed over the past ten years. This publication is one of a series of Technical Reports on uranium ore processing that have been prepared by the Division of Nuclear Fuel Cycle and Waste Management at the IAEA. A complete list of these reports is included as an addendum. Refs, figs and tabs

Technical Network

CERN Multimedia

2007-01-01

In order to optimize the management of the Technical Network (TN), to ease the understanding and purpose of devices connected to the TN, and to improve security incident handling, the Technical Network Administrators and the CNIC WG have asked IT/CS to verify the "description" and "tag" fields of devices connected to the TN. Therefore, persons responsible for systems connected to the TN will receive email notifications from IT/CS asking them to add the corresponding information in the network database. Thank you very much for your cooperation. The Technical Network Administrators & the CNIC WG

Review of the Tritium Extraction Facility design

International Nuclear Information System (INIS)

Barton, R.W.; Bamdad, F.; Blackman, J.

2000-01-01

The Defense Nuclear Facilities Safety Board (DNFSB) is an independent executive branch agency responsible for technical safety oversight of the US Department of Energy's (DOE's) defense nuclear facilities. One of DNFSB's responsibilities is the review of design and construction projects for DOE's defense nuclear facilities to ensure that adequate health and safety requirements are identified and implemented. These reviews are performed with the expectation that facility designs are being developed within the framework of a site's Integrated Safety Management (ISM) program. This paper describes the application of ISM principles in DNFSB's ongoing review of the Tritium Extraction Facility (TEF) design/construction project

Review of the Tritium Extraction Facility Design

International Nuclear Information System (INIS)

Ronald W. Barton; Farid Bamdad; Joel Blackman

2000-01-01

The Defense Nuclear Facilities Safety Board (DNFSB) is an independent executive branch agency responsible for technical safety oversight of the U.S. Department of Energy's (DOE's) defense nuclear facilities. One of DNFSB's responsibilities is the review of design and construction projects for DOE's defense nuclear facilities to ensure that adequate health and safety requirements are identified and implemented. These reviews are performed with the expectation that facility designs are being developed within the framework of a site's Integrated Safety Management (ISM) program. This paper describes the application of ISM principles in DNFSB's ongoing review of the Tritium Extraction Facility (TEF) design/construction project

Legitimizing Technical Communication in English Departments: Carolyn Miller's "Humanistic Rationale for Technical Writing"

Science.gov (United States)

Moore, Patrick

2006-01-01

Carolyn Miller's oft-cited "Humanistic Rationale for Technical Writing," published in 1979, tries to give technical communication faculty more cultural capital in English departments controlled by literature professors. Miller replaces a positivistic emphasis in technical communication pedagogy with rhetoric. She shows how technical knowledge is…

Strategy of technical innovation

International Nuclear Information System (INIS)

Lee, Ga Jong

1990-12-01

This book deals with policy of scientific technique and technical innovation such as research for development and types of technical innovation, historical development and process of technical innovation, economic growth, technology change and investment for research and development, structure and form of technical transfer with the meaning process, from, structure and theory, economic growth and investment of research and development with experiential analysis and case study on strategy of technical innovation in electron and fine chemical industry.

Robust resilience and substantial interest: a survey of pharmacological cognitive enhancement among university students in the UK and Ireland.

Directory of Open Access Journals (Sweden)

Ilina Singh

Full Text Available Use of 'smart drugs' among UK students is described in frequent media reports as a rapidly increasing phenomenon. This article reports findings from the first large-scale survey of pharmacological cognitive enhancement (PCE among students in the UK and Ireland. Conducted from February to September 2012, a survey of a convenience sample of 877 students measured PCE prevalence, attitudes, sources, purposes and ethics. Descriptive and logistic regression statistical methods were used to analyse the data. Lifetime prevalence of PCE using modafinil, methylphenidate or Adderall was under 10%, while past regular and current PCE users of these substances made up between 0.3%-4% of the survey population. A substantial majority of students was unaware of and/or uninterested in PCE; however about one third of students were interested in PCE. PCE users were more likely to be male, British and older students; predictors of PCE use included awareness of other students using PCEs, ADHD symptomatology, ethical concerns, and alcohol and cannabis use. The survey addresses the need for better evidence about PCE prevalence and practices among university students in the UK. We recommend PCE-related strategies for universities based on the survey findings.

Urology technical and non-technical skills development: the emerging role of simulation.

Science.gov (United States)

Rashid, Prem; Gianduzzo, Troy R J

2016-04-01

To review the emerging role of technical and non-technical simulation in urological education and training. A review was conducted to examine the current role of simulation in urology training. A PUBMED search of the terms 'urology training', 'urology simulation' and 'urology education' revealed 11,504 titles. Three hundred and fifty-seven abstracts were identified as English language, peer reviewed papers pertaining to the role of simulation in urology and related topics. Key papers were used to explore themes. Some cross-referenced papers were also included. There is an ongoing need to ensure that training time is efficiently utilised while ensuring that optimal technical and non-technical skills are achieved. Changing working conditions and the need to minimise patient harm by inadvertent errors must be taken into account. Simulation models for specific technical aspects have been the mainstay of graduated step-wise low and high fidelity training. Whole scenario environments as well as non-technical aspects can be slowly incorporated into the curriculum. Doing so should also help define what have been challenging competencies to teach and evaluate. Dedicated time, resources and trainer up-skilling are important. Concurrent studies are needed to help evaluate the effectiveness of introducing step-wise simulation for technical and non-technical competencies. Simulation based learning remains the best avenue of progressing surgical education. Technical and non-technical simulation could be used in the selection process. There are good economic, logistic and safety reasons to pursue the process of ongoing development of simulation co-curricula. While the role of simulation is assured, its progress will depend on a structured program that takes advantage of what can be delivered via this medium. Overall, simulation can be developed further for urological training programs to encompass technical and non-technical skill development at all stages, including

Training of technical staff and technical staff managers

International Nuclear Information System (INIS)

Moody, G.F.

1991-01-01

The purpose of Technical Staff and Technical Staff Managers training is to provide job skills enhancement to individuals selected to fill key technical positions within a nuclear utility. This training is unique in that unlike other training programs accredited by the National Academy for Nuclear Training, it does not lead to specific task qualification. The problems encountered when determining the student population and curriculum are a direct result of this major difference. Major problems encountered are determining who should attend the training, what amount of training is necessary and sufficient, and how to obtain the best feedback in order to effect substantive program improvements. These topics will be explored and possible solutions discussed

Technical Network

CERN Multimedia

2007-01-01

In order to optimise the management of the Technical Network (TN), to facilitate understanding of the purpose of devices connected to the TN and to improve security incident handling, the Technical Network Administrators and the CNIC WG have asked IT/CS to verify the "description" and "tag" fields of devices connected to the TN. Therefore, persons responsible for systems connected to the TN will receive e-mails from IT/CS asking them to add the corresponding information in the network database at "network-cern-ch". Thank you very much for your cooperation. The Technical Network Administrators & the CNIC WG

Technical and surgical aspects of the sphenopalatine ganglion (SPG) microstimulator insertion procedure

DEFF Research Database (Denmark)

Assaf, A T; Hillerup, S; Rostgaard, J

2016-01-01

into the pterygopalatine fossa (PPF) is presented herein. Technical aspects include detailed descriptions of the preoperative planning using computed tomography or cone beam computed tomography scans for presurgical digital microstimulator insertion into the patient-specific anatomy and intraoperative verification......), and removal (n=5). This SPG microstimulator insertion procedure has sequelae comparable to other oral cavity procedures including tooth extractions, sinus surgery, and dental implant placement. Twenty-five of 29 subjects (86%) completing a self-assessment questionnaire indicated that the surgical effects were...

A rapid extraction of landslide disaster information research based on GF-1 image

Science.gov (United States)

Wang, Sai; Xu, Suning; Peng, Ling; Wang, Zhiyi; Wang, Na

2015-08-01

In recent years, the landslide disasters occurred frequently because of the seismic activity. It brings great harm to people's life. It has caused high attention of the state and the extensive concern of society. In the field of geological disaster, landslide information extraction based on remote sensing has been controversial, but high resolution remote sensing image can improve the accuracy of information extraction effectively with its rich texture and geometry information. Therefore, it is feasible to extract the information of earthquake- triggered landslides with serious surface damage and large scale. Taking the Wenchuan county as the study area, this paper uses multi-scale segmentation method to extract the landslide image object through domestic GF-1 images and DEM data, which uses the estimation of scale parameter tool to determine the optimal segmentation scale; After analyzing the characteristics of landslide high-resolution image comprehensively and selecting spectrum feature, texture feature, geometric features and landform characteristics of the image, we can establish the extracting rules to extract landslide disaster information. The extraction results show that there are 20 landslide whose total area is 521279.31 .Compared with visual interpretation results, the extraction accuracy is 72.22%. This study indicates its efficient and feasible to extract earthquake landslide disaster information based on high resolution remote sensing and it provides important technical support for post-disaster emergency investigation and disaster assessment.

Effects of the Molybdenum Oxide/Metal Anode Interfaces on Inverted Polymer Solar Cells

International Nuclear Information System (INIS)

Wu Jiang; Guo Xiao-Yang; Xie Zhi-Yuan

2012-01-01

Inverted polymer solar cells with molybdenum oxide (MoO 3 ) as an anode buffer layer and different metals (Al or Ag) as anodes are studied. It is found that the inverted cell with a top Ag anode demonstrates enhanced charge collection and higher power conversion efficiency (PCE) compared to the cell with a top Al anode. An 18% increment of PCE is obtained by replacing Al with Ag as the top anode. Further studies show that an interfacial dipole pointing from MoO 3 to Al is formed at MoO 3 /Al interfaces due to electron transfer from Al to MoO 3 while this phenomenon cannot be observed at MoO 3 /Ag interfaces. It is speculated that the electric field at the MoO 3 /Al interface would hinder hole extraction, and hence reduce the short-circuit current

Enhanced Attenuation Technologies: Passive Soil Vapor Extraction

Energy Technology Data Exchange (ETDEWEB)

Vangelas, K.; Looney, B.; Kamath, R.; Adamson, D.; Newell, C.

2010-03-15

Passive soil vapor extraction (PSVE) is an enhanced attenuation (EA) approach that removes volatile contaminants from soil. The extraction is driven by natural pressure gradients between the subsurface and atmosphere (Barometric Pumping), or by renewable sources of energy such as wind or solar power (Assisted PSVE). The technology is applicable for remediating sites with low levels of contamination and for transitioning sites from active source technologies such as active soil vapor extraction (ASVE) to natural attenuation. PSVE systems are simple to design and operate and are more cost effective than active systems in many scenarios. Thus, PSVE is often appropriate as an interim-remedial or polishing strategy. Over the past decade, PSVE has been demonstrated in the U.S. and in Europe. These demonstrations provide practical information to assist in selecting, designing and implementing the technology. These demonstrations indicate that the technology can be effective in achieving remedial objectives in a timely fashion. The keys to success include: (1) Application at sites where the residual source quantities, and associated fluxes to groundwater, are relatively low; (2) Selection of the appropriate passive energy source - barometric pumping in cases with a deep vadose zone and barrier (e.g., clay) layers that separate the subsurface from the atmosphere and renewable energy assisted PSVE in other settings and where higher flow rates are required. (3) Provision of sufficient access to the contaminated vadose zones through the spacing and number of extraction wells. This PSVE technology report provides a summary of the relevant technical background, real-world case study performance, key design and cost considerations, and a scenario-based cost evaluation. The key design and cost considerations are organized into a flowchart that dovetails with the Enhanced Attenuation: Chlorinated Organics Guidance of the Interstate Technology and Regulatory Council (ITRC). The PSVE

TECHNICAL COORDINATION

CERN Multimedia

A. Ball

2010-01-01

Operational Experience At the end of the first full-year running period of LHC, CMS is established as a reliable, robust and mature experiment. In particular common systems and infrastructure faults accounted for <0.6 % CMS downtime during LHC pp physics. Technical operation throughout the entire year was rather smooth, the main faults requiring UXC access being sub-detector power systems and rack-cooling turbines. All such problems were corrected during scheduled technical stops, in the shadow of tunnel access needed by the LHC, or in negotiated accesses or access extensions. Nevertheless, the number of necessary accesses to the UXC averaged more than one per week and the technical stops were inevitably packed with work packages, typically 30 being executed within a few days, placing a high load on the coordination and area management teams. It is an appropriate moment for CMS Technical Coordination to thank all those in many CERN departments and in the Collaboration, who were involved in CMS techni...

Risk of breast cancer following exposure to tetrachloroethylene-contaminated drinking water in Cape Cod, Massachusetts: reanalysis of a case-control study using a modified exposure assessment

Directory of Open Access Journals (Sweden)

Webster Thomas F

2011-05-01

Full Text Available Abstract Background Tetrachloroethylene (PCE is an important occupational chemical used in metal degreasing and drycleaning and a prevalent drinking water contaminant. Exposure often occurs with other chemicals but it occurred alone in a pattern that reduced the likelihood of confounding in a unique scenario on Cape Cod, Massachusetts. We previously found a small to moderate increased risk of breast cancer among women with the highest exposures using a simple exposure model. We have taken advantage of technical improvements in publically available software to incorporate a more sophisticated determination of water flow and direction to see if previous results were robust to more accurate exposure assessment. Methods The current analysis used PCE exposure estimates generated with the addition of water distribution modeling software (EPANET 2.0 to test model assumptions, compare exposure distributions to prior methods, and re-examine the risk of breast cancer. In addition, we applied data smoothing to examine nonlinear relationships between breast cancer and exposure. We also compared a set of measured PCE concentrations in water samples collected in 1980 to modeled estimates. Results Thirty-nine percent of individuals considered unexposed in prior epidemiological analyses were considered exposed using the current method, but mostly at low exposure levels. As a result, the exposure distribution was shifted downward resulting in a lower value for the 90th percentile, the definition of "high exposure" in prior analyses. The current analyses confirmed a modest increase in the risk of breast cancer for women with high PCE exposure levels defined by either the 90th percentile (adjusted ORs 1.0-1.5 for 0-19 year latency assumptions or smoothing analysis cut point (adjusted ORs 1.3-2.0 for 0-15 year latency assumptions. Current exposure estimates had a higher correlation with PCE concentrations in water samples (Spearman correlation coefficient = 0.65, p

Algal Lipid Extraction and Upgrading to Hydrocarbons Technology Pathway

Energy Technology Data Exchange (ETDEWEB)

Davis, Ryan; Biddy, Mary J.; Jones, Susanne B.

2013-03-31

In support of the Bioenergy Technologies Office, the National Renewable Energy Laboratory (NREL) and the Pacific Northwest National Laboratory (PNNL) are undertaking studies of biomass conversion technologies to identify barriers and target research toward reducing conversion costs. Process designs and preliminary economic estimates for each of these pathway cases were developed using rigorous modeling tools (Aspen Plus and Chemcad). These analyses incorporated the best information available at the time of development, including data from recent pilot and bench-scale demonstrations, collaborative industrial and academic partners, and published literature and patents. This technology pathway case investigates the cultivation of algal biomass followed by further lipid extraction and upgrading to hydrocarbon biofuels. Technical barriers and key research needs have been assessed in order for the algal lipid extraction and upgrading pathway to be competitive with petroleum-derived gasoline, diesel and jet range hydrocarbon blendstocks.

Pharmaceutical Cognitive Enhancement in Greek University Students: Differences Between Users and Non-Users in Social Cognitive Variables, Burnout, and Engagement.

Science.gov (United States)

Lazuras, Lambros; Ypsilanti, Antonia; Lamprou, Efthymios; Kontogiorgis, Christos

2017-06-07

Pharmaceutical cognitive enhancement (PCE) represents the non-medical use of prescribed medication for the improvement of cognitive functioning and academic performance. Although there are some studies about PCE prevalence, it is less clear how users and non-users of PCE substances differ with respect to their positive and negative student experiences (e.g. academic burnout and engagement with studies) and in social cognitive variables that relate to decision-making and self-regulation of PCE use. The present study assessed whether students with different experiences of PCE substance use displayed differences in academic burnout, study engagement, and social cognitive variables relevant to PCE use. Three hundred and forty-seven university students (mean age (M) = 22.15 years, SD = 1.69; 54% females) completed a battery of anonymous questionnaires on academic burnout, engagement with studies, social cognitive variables relevant to PCE use, and self-reported use of PCE substances and non-prescribed nutritional supplements. Three user groups emerged, namely non-users (51.9%, n = 180), single users of non-prescribed dietary supplements (25.4%, n = 88), and dual users of both non-prescribed dietary supplements and PCE (22.8%, n = 79). Multivariate analysis of variance indicated significant differences among the three user groups in intentions, attitudes, social norms, and anticipated regret toward PCE use. No significant differences were observed with respect to academic burnout and work engagement. The findings show that university students may engage in PCE use independent of their student experiences. Rather, a chemically assisted performance enhancement mindset seems to differentiate users from non-users of PCE substances.

Effect of thermal annealing treatment with titanium chelate on buffer layer in inverted polymer solar cells

Energy Technology Data Exchange (ETDEWEB)

Liu, Zhiyong [College of Science, Shenyang Agricultural University, Shenyang 110866 (China); Wang, Ning, E-mail: ning_wang@outlook.com [School of Electrical and Electronic and Engineering, Nanyang Technological University 639798 (Singapore); Fu, Yan, E-mail: 1060945062@qq.com [College of Science, Shenyang Agricultural University, Shenyang 110866 (China)

2016-12-15

Highlights: • The TIPD layer as electron extraction layer and instead of Ca or LiF. • Impact of the work function of TIPD layer by thermal annealing treatment. • Importance of TIPD layer as electron extraction layer for work function and potential barrier. - Abstract: The solution processable electron extraction layer (EEL) is crucial for polymer solar cells (PSCs). Here, we investigated titanium (diisopropoxide) bis(2,4-pentanedionate) (TIPD) as an EEL and fabricated inverted PSCs with a blend of poly(3-hexylthiophene) (P3HT) and indene-C60 bisadduct (ICBA) acting as the photoactive layer, with a structure of ITO/TIPD/P3HT:ICBA/MoO{sub 3}/Ag. After thermal annealing treatment at 150 °C for 15 min, the PSC performances increased from 3.85% to 6.84% and they achieve stable power conversion efficiency (PCE), with a similar PCE compared with TiO{sub 2} as an EEL by the vacuum evaporated method. Fourier transform infrared spectroscopy (FTIR) and ultraviolet photoelectron spectroscopy (UPS) confirmed that the TIPD decomposed and formed the Ti=O bond, and the energy level of the lowest unoccupied molecular orbital and the highest occupied molecular orbital increased. The space charge limited current (SCLC) measurements further confirmed the improvement in electron collection and the transport ability using TIPD as the EEL and thermal annealing.

Systems principles of planning the net cost of oil and gas extraction

Energy Technology Data Exchange (ETDEWEB)

Ryazanova, N I

1979-01-01

The automated system of calculation of ASPC ''oil extraction'' is developed in order to improve the existing system of planning of the oil extracting sector. The most complete expression of the systems construction of the plan is found in the section ''net cost and profit.'' Unity of the production process advances definite requirements for construction of the plan for net cost of oil and gas extraction as the model of this unified process. According to these requirements, the plan for net cost must be developed on the basis of interrelationship of the indicators of the plan for net cost within the section and with indicators of other sections of the plan, methodological unity and continuity of the methods of planning net cost by elements of outlays, articles of calculation and technical-economic factors, methodological continuity of regimes and stages of planning, as well as based on methodological continuity of the control levels. The listed requirements are principles for systems planning of the net cost of oil and gas extraction. These principles guarantee improvement in planning of net cost of oil and gas extraction according to the requirements made for the national economic planning.

Perubahan Nilai Ekivalensi Mobil Penumpang Akibat Perubahan Karakteristik Operasional Kendaraan di Jalan Kota Semarang

Directory of Open Access Journals (Sweden)

EPF. Eko Yulipriyono

2017-07-01

Full Text Available Passenger Car Equivalent (PCE is a conversion factor to make equal the various types of vehicles that operating on the road section into one type of vehicles i.e. passenger cars. Indonesian Highway Capacity Manual (MKJI 1997 has set the PCE values for various types of vehicle groups either motorized. PCE values of various types of vehicles are not absolute because many factors that affect can change over time and development of automotive technology. This study aimed to find out the changes of PCE value that occurs. As for the purpose of research to determine the current number of PCE values due to the change of operational characteristics of vehicles on a highway especially for urban highways. Data analysis for the determination of PCE values used: time headway method, speed method, capacity method, and vehicle dimension method. The conclusion of this study: PCE of light vehicles (LV = 1 still in accordance with MJKI 1997; PCE of heavy vehicles (HV varied depending on the road types. PCE of heavy vehicles that according to MKJI 1997 is used as a median; PCE of motorcycles (MC of MKJI 1997 need to be adjusted to 0.4 or more, particularly in the calculation of actualy traffic flow.

The Data Extraction Using Distributed Crawler Inside Multi-Agent System

Directory of Open Access Journals (Sweden)

Karel Tomala

2013-01-01

Full Text Available The paper discusses the use of web crawler technology. We created an application based on standard web crawler. Our application is determined for data extraction. Primarily, the application was designed to extract data using keywords from a social network Twitter. First, we created a standard crawler, which went through a predefined list of URLs and gradually download page content of each of the URLs. Page content was then parsed and important text and metadata were stored in a database. Recently, the application was modified in to the form of the multi-agent system. The system was developed in the C# language, which is used to create web applications and sites etc. Obtained data was evaluated graphically. The system was created within Indect project at the VSB-Technical University of Ostrava.

EXPANSION OF OBJECTIVES OF THE PRACTICAL APPLICATION OF TECHNICAL AUDIT AT RAILWAY TRANSPORT ENTERPRISES

Directory of Open Access Journals (Sweden)

A. M. Okorokov

2017-12-01

Full Text Available Purpose. The work is aimed to study, compare and summarize information on the current state and peculiarities of conducting technical audit in various branches of business in order to obtain the possibility of developing proposals for expanding the objectives of this procedure in railway enterprises. Methodology. In the course of the research there were used the methods of analysis and synthesis to study the content and basic provisions of scientific publications, normative legal acts of Ukraine, and other data on conducting technical audit in the field of industry, construction, gas extraction, electricity, marine and rail transport, followed by their comparison and generalization. Findings. Taking into account the positive experience of the audit carrying out in other sectors the article expands the goals of practical application of technical audit in railway transport enterprises. This envisages assessment of the current technical condition and the residual life of exploited vehicles and equipment of PJSC "Ukrzaliznytsia". As a result, there is an opportunity to detect and activate the reserves for improving the efficiency of railway transport enterprises, estimating and forecasting the costs for repair cycles and modernization, as well as for increasing the train safety level and improving investment attractiveness of the industry. Originality. The obtained results make it possible to broaden the concept of "technical audit" in railway transport, to define the purpose of its carrying out and the list of tasks. Application of the extended technical audit will provide an opportunity to receive objective information on the actual technical condition of the objects of the railway infrastructure, means of transport and equipment, and to use it for the formation of development programs as individual enterprises and the railway as a whole. Practical value. Expanding the goals of practical application of the technical audit at railway enterprises

Beamstrahlung Photon Load on the TESLA Extraction Septum Blade(LCC-0104)

Energy Technology Data Exchange (ETDEWEB)

Seryi, A

2003-10-02

This note describes work performed in the framework of the International Linear Collider Technical Review Committee [1] to estimate the power load on the TESLA extraction septum blade due to beamstrahlung photons. It is shown, that under realistic conditions the photon load can be several orders of magnitude higher than what was estimated in the TESLA TDR [2] for the ideal Gaussian beams, potentially representing a serious limitation of the current design.

Beamstrahlung Photon Load on the TESLA Extraction Septum Blade(LCC-0104)

International Nuclear Information System (INIS)

Seryi, A

2003-01-01

This note describes work performed in the framework of the International Linear Collider Technical Review Committee [1] to estimate the power load on the TESLA extraction septum blade due to beamstrahlung photons. It is shown, that under realistic conditions the photon load can be several orders of magnitude higher than what was estimated in the TESLA TDR [2] for the ideal Gaussian beams, potentially representing a serious limitation of the current design

Handbook of Technical Communication

OpenAIRE

Mehler , Alexander; Romary , Laurent; Gibbon , Dafydd

2012-01-01

International audience; The handbook "Technical Communication" brings together a variety of topics which range from the role of technical media in human communication to the linguistic, multimodal enhancement of present-day technologies. It covers the area of computer-mediated text, voice and multimedia communication as well as of technical documentation. In doing so, the handbook takes professional and private communication into account. Special emphasis is put on technical communication bas...

Expressive/Exploratory Technical Writing (XTW) in Engineering: Shifting the Technical Writing Curriculum

Science.gov (United States)

Warnock, Scott; Kahn, Michael

2007-01-01

While the importance of "expressive writing," or informal, self-directed writing, has been well established, teachers underutilize it, particularly in technical writing courses. We introduce the term expressive/exploratory technical writing (XTW), which is the use of informal, self-directed writing to problem-solve in technical fields. We describe…

Playing on strengths : technical innovations keep Canadian industry on top

International Nuclear Information System (INIS)

Harvie, W.

1997-01-01

The Western Canada Sedimentary Basin is one of Canada's major petroleum regions. Some fields in the region have been in production for 80 years. Since most of the major discoveries have been made, the challenge today is to use new technologies to find smaller reservoirs and to extract as much oil as possible from the depleting reserves. The following technical innovations were developed by Canadian companies for enhanced oil recovery: (1) steam assisted gravity drainage for heavy oil, (2) horizontal drilling, (3) coiled tube drilling, (4) single well steam assisted gravity drainage, (5) hydrocyclone technology in which briny water is sent down the borehole for reinjection and in which centrifugal force sends the lighter oil to the middle of the hydrocyclone where it is collected, and (6) portable top drives aimed at newer versions of large land drilling rigs and offshore operations. Multi-lateral techniques have also been used to increase production on heavy oil properties. These and other technical innovations are recognized as the single best advantage that Canadians have to offer the global marketplace. 4 figs

Mesoscopic Oxide Double Layer as Electron Specific Contact for Highly Efficient and UV Stable Perovskite Photovoltaics.

Science.gov (United States)

Tavakoli, Mohammad Mahdi; Giordano, Fabrizio; Zakeeruddin, Shaik Mohammed; Grätzel, Michael

2018-04-11

The solar to electric power conversion efficiency (PCE) of perovskite solar cells (PSCs) has recently reached 22.7%, exceeding that of competing thin film photovoltaics and the market leader polycrystalline silicon. Further augmentation of the PCE toward the Shockley-Queisser limit of 33.5% warrants suppression of radiationless carrier recombination by judicious engineering of the interface between the light harvesting perovskite and the charge carrier extraction layers. Here, we introduce a mesoscopic oxide double layer as electron selective contact consisting of a scaffold of TiO 2 nanoparticles covered by a thin film of SnO 2 , either in amorphous (a-SnO 2 ), crystalline (c-SnO 2 ), or nanocrystalline (quantum dot) form (SnO 2 -NC). We find that the band gap of a-SnO 2 is larger than that of the crystalline (tetragonal) polymorph leading to a corresponding lift in its conduction band edge energy which aligns it perfectly with the conduction band edge of both the triple cation perovskite and the TiO 2 scaffold. This enables very fast electron extraction from the light perovskite, suppressing the notorious hysteresis in the current-voltage ( J-V) curves and retarding nonradiative charge carrier recombination. As a result, we gain a remarkable 170 mV in open circuit photovoltage ( V oc ) by replacing the crystalline SnO 2 by an amorphous phase. Because of the quantum size effect, the band gap of our SnO 2 -NC particles is larger than that of bulk SnO 2 causing their conduction band edge to shift also to a higher energy thereby increasing the V oc . However, for SnO 2 -NC there remains a barrier for electron injection into the TiO 2 scaffold decreasing the fill factor of the device and lowering the PCE. Introducing the a-SnO 2 coated mp-TiO 2 scaffold as electron extraction layer not only increases the V oc and PEC of the solar cells but also render them resistant to UV light which forebodes well for outdoor deployment of these new PSC architectures.

Synergistic effect of nano-sized mackinawite with cyano-cobalamin in cement slurries for reductive dechlorination of tetrachloroethylene

Energy Technology Data Exchange (ETDEWEB)

Kyung, Daeseung [Department of Civil and Environmental Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of); Sihn, Youngho [Department of Nuclear and Quantum Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of); Kim, Sangwoo [Department of Civil and Environmental Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of); Bae, Sungjun [Department of Environmental Engineering, Konkuk University, 120 Neungdong-ro, Gwangjin-gu, Seoul 05029 (Korea, Republic of); Amin, Muhammad Tahir; Alazba, Abdulrahman Ali [Alamoudi Water Chair, King Saud University, Riyadh 11451 (Saudi Arabia); Lee, Woojin, E-mail: woojin_lee@kaist.ac.kr [Department of Civil and Environmental Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of)

2016-07-05

Highlights: • Complete degradation of PCE was observed in nFeS-Cbl(III)-cement at pH 12. • PCE was completely degraded to non-chlorinated organic compounds by this system. • Co redox couple and Ca species in cement played a pivotal role for PCE reduction. • Increases in Cbl(III) concentration, cement ratio, and pH enhanced PCE degradation. • Efficiency of the system for PCE reduction was good even at high concentration of PCE. - Abstract: Experiments were conducted to investigate the reductive dechlorination of tetrachloroethylene (PCE) by nano-Mackinawite (nFeS) with cyano-cobalamin (Cbl(III)) in cement slurries. Almost complete degradation of PCE by nFeS-Cbl(III) was observed in cement slurries in 5 h and its degradation kinetics (k{sub obs-PCE} = 0.57 h{sup −1}) was 6-times faster than that of nFeS-Cbl(III) without the cement slurries. PCE was finally transformed to non-chlorinated organic compounds such as ethylene, acetylene, and C3-C4 hydrocarbons by nFeS-Cbl(III) in cement slurries. X-ray photoelectron spectroscopy and PCE degradation by cement components (SiO{sub 2}, Al{sub 2}O{sub 3}, and CaO) revealed that both the reduced Co species in Cbl(III) and the presence of Ca in cement played an important role for the enhanced reductive dechlorination of PCE. The increase in the concentration of Cbl(III) (0.005–0.1 mM), cement ratio (0.05–0.2), and suspension pH (11.5–13.5) accelerated the PCE degradation kinetics by providing more favorable environments for the production of reactive Ca species and reduction of Co species. We also observed that the degradation efficiency of PCE by nFeS-Cbl(III)-cement lasted even at high concentration of PCE. The experimental results obtained from this study could provide fundamental knowledge of redox interactions among nFeS, Cbl(III), and cement, which could significantly enhance reductive dechlorination of chlorinated organics in contaminated natural and engineered environments.

Technical rules in law

Energy Technology Data Exchange (ETDEWEB)

Debelius, J

1978-08-01

An important source of knowledge for technical experts is the state of the art reflected by catalogues of technical rules. Technical rules may also achieve importance in law due to a legal transformation standard. Here, rigid and flexible reference are controversial with regard to their admissibility from the point of view of constitutional law. In case of a divergence from the generally accepted technical rules, it is assumed - refutably - that the necessary care had not been taken. Technical rules are one out of several sources of information; they have no normative effect. This may result in a duty of anyone applying them to review the state of technology himself.

Technical rules in law

International Nuclear Information System (INIS)

Debelius, J.

1978-01-01

An important source of knowledge for technical experts is the state of the art reflected by catalogues of technical rules. Technical rules may also achieve importance in law due to a legal transformation standard. Here, rigid and flexible reference are controversial with regard to their admissibility from the point of view of constitutional law. In case of a divergence from the generally accepted technical rules, it is assumed - refutably - that the necessary care had not been taken. Technical rules are one out of several sources of information; they have no normative effect. This may result in a duty of anyone applying them to review the state of technology himself. (orig.) [de

TECHNICAL COORDINATION

CERN Multimedia

A. Ball

2010-01-01

Operational Experience Since the closure of the detector in February, the technical operation of CMS has been quite smooth and reliable. Some minor interventions in UXC were required to cure failures of power supplies, fans, readout boards and rack cooling connections, but all these failures were repaired in scheduled technical stops or parasitically during access dedicated to fixing LHC technical problems. The only occasion when CMS had to request an access between fills was to search for the source of an alarm from the leak-detection cables mounted in the DT racks. After a few minutes of diagnostic search, a leaking air-purge was found. Replacement was complete within 2 hours. This incident demonstrated once more the value of these leak detection cables; the system will be further extended (during the end of year technical stop) to cover more racks in UXC and the floor beneath the detector. The magnet has also been operating reliably and reacted correctly to the 14s power cut on 29 May (see below). In or...

Proceedings of the meeting on uranium exploration, mining and extraction

International Nuclear Information System (INIS)

1996-01-01

Meeting on uranium exploration, mining, and extraction is aimed to expedite information exchange among researchers from the National Atomic Energy Agency (BATAN), their international colleagues, the higher education institutions,and other interested scientific communities on the latest development on Kalan uranium minerals exploration, mining, and extraction. Nuclear Minerals Development Centre (PPBGN) roles in nuclear energy provision, the theme of the meeting, reflect current advancements of the Centre in fulfilling its major tasks and responsibilities. In order to assist PPBGN better to assume its roles and responsibilities, the meeting is expected to bring forth essential solutions for problems and difficulties relevant to PPBGN's activities. Hence, the scope of the meeting will be limited to discussion on the status of nuclear minerals exploration, mining, and extraction technologies in Indonesia as well as the related environmental and workplace safeties in uranium mining and milling. Ten technical papers were presented in meeting, including four topics on exploration status and technology, three subject matter on mining, two presentations on milling, and one paper on environmental and workplace safeties

Technical feasibility of the Diamex process

International Nuclear Information System (INIS)

Sorel, Ch

2007-01-01

Full text of publication follows. The DIAMEX process was developed to facilitate the separation of the trivalent actinides from the trivalent lanthanides. It consists in co-extracting the trivalent actinides and lanthanides using a diamide extractant: Di-Methyl Di-Octyl Hexyl Ethoxy Malonamide (DMDOHEMA). The flow-sheet comprises: Co-extraction at high acidity (3 M HNO 3 ) of the trivalent actinides and lanthanides by the diamide; scrubbing of some fission products (Zr, Mo, Fe, Pd) by a mixture of oxalic acid and HEDTA, followed by de-acidification to prepare for the next step; stripping of the actinides + lanthanides at low acidity; solvent treatment prior to recycling. This flow-sheet was successfully tested at laboratory scale from 1999 to 2003 in mixer-settlers and subsequently in ECLHA centrifugal extractors on active solutions from the dissolution of actual spent fuel samples. Actinide recovery factors above 99.9% were obtained with high purification factors for spurious fission products. The main objectives of the final ''technical feasibility'' demonstration tests at the end of 2005 with a PUREX raffinate solution were to test continuous solvent recycling (not included during the earlier tests) and to carry out essential operations in continuous contactors representative of pulsed columns that could be used at industrial scale. We therefore decided to carry out the demonstration in the shielded process line (CBP) with some of the devices already used for a PUREX test. During these tests the first two steps in the flow-sheet were therefore carried out in pulsed columns 4 meters high; An+Ln stripping was performed in mixer-settlers and the solvent treatment in ECRAN. The americium and curium recovery yield exceeded 99.9% and the decontamination factors obtained at the end of the test with respect to the fission products Zr, Mo and Fe were 800, 100 and 10, respectively. (author)

Methodology for technical risk assessment

International Nuclear Information System (INIS)

Waganer, L.M.; Zuckerman, D.S.

1983-01-01

A methodology has been developed for and applied to the assessment of the technical risks associated with an evolving technology. This methodology, originally developed for fusion by K. W. Billman and F. R. Scott at EPRI, has been applied to assess the technical risk of a fuel system for a fusion reactor. Technical risk is defined as the risk that a particular technology or component which is currently under development will not achieve a set of required technical specifications (i.e. probability of failure). The individual steps in the technical risk assessment are summarized. The first step in this methodology is to clearly and completely quantify the technical requirements for the particular system being examined. The next step is to identify and define subsystems and various options which appear capable of achieving the required technical performance. The subsystem options are then characterized regarding subsystem functions, interface requirements with the subsystems and systems, important components, developmental obstacles and technical limitations. Key technical subsystem performance parameters are identified which directly or indirectly relate to the system technical specifications. Past, existing and future technical performance data from subsystem experts are obtained by using a Bayesian Interrogation technique. The input data is solicited in the form of probability functions. Thus the output performance of the system is expressed as probability functions

Statistical model of planning technological indicators for oil extraction

Energy Technology Data Exchange (ETDEWEB)

Galeyev, R G; Lavushchenko, V P; Sheshnev, A S

1979-01-01

The efficiency of the process of oil extraction is determined by the effect of a number of interrelated technological indicators. Analytical expression of the interrelationships of the indicators was represented by an econometric model consisting of a system of linear regression equations. The basic advantage of these models is the possibility of calculating in them different, significantly important interrelationships. This makes it possible to correlate all calculations into a single logically noncontradictory balanced system. The developed model of the technological process of oil extraction makes it possible to significantly facilitate calculation and planning of its basic indicators with regard for system and balance requirements, makes it possible to purposefully generate new variants. In this case because of the optimal distribution of the volumes of geological-technical measures, a decrease in the total outlays for their implementation is achieved. Thus for the Berezovskiy field, this saving was R 150,000.

Selective Gaseous Extraction: Research, Development and Training for Isotope Production, Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Bertch, Timothy C, [General Atomics

2014-03-31

General Atomics and the University of Missouri Research Reactor (MURR) completed research and development of selective gaseous extraction of fission products from irradiated fuel, which included training and education of MURR students. The process used porous fuel and after irradiation flowed product gases through the fuel to selectively removed desired fission products with the primary goal of demonstrating the removal of rhodium 105. High removal rates for the ruthenium/rhodium (Ru/Rh), tellurium/iodine (Te/I) and molybdenum/technetium (Mo/Tc) series were demonstrated. The success of this research provides for the reuse of the target for further production, significantly reducing the production of actinide wastes relative to processes that dissolve the target. This effort was conducted under DOE funding (DE-SC0007772). General Atomics objective of the project was to conduct R&D on alternative methods to produce a number of radioactive isotopes currently needed for medical and industry applications to include rhodium-105 and other useful isotopes. Selective gaseous extraction was shown to be effective at removing radioisotopes of the ruthenium/rhodium, tellurium/iodine and molybdenum/technetium decay chains while having trace to no quantities of other fission products or actinides. This adds a new, credible method to the area of certain commercial isotope production beyond current techniques, while providing significant potential reduction of process wastes. Waste reduction, along with reduced processing time/cost provides for superior economic feasibility which may allow domestic production under full cost recovery practices. This provides the potential for improved access to domestically produced isotopes for medical diagnostics and treatment at reduced cost, providing for the public good.

Air extraction in gas turbines burning coal-derived gas

Energy Technology Data Exchange (ETDEWEB)

Yang, Tah-teh; Agrawal, A.K.; Kapat, J.S.

1993-11-01

In the first phase of this contracted research, a comprehensive investigation was performed. Principally, the effort was directed to identify the technical barriers which might exist in integrating the air-blown coal gasification process with a hot gas cleanup scheme and the state-of-the-art, US made, heavy-frame gas turbine. The guiding rule of the integration is to keep the compressor and the expander unchanged if possible. Because of the low-heat content of coal gas and of the need to accommodate air extraction, the combustor and perhaps, the flow region between the compressor exit and the expander inlet might need to be modified. In selecting a compressed air extraction scheme, one must consider how the scheme affects the air supply to the hot section of the turbine and the total pressure loss in the flow region. Air extraction must preserve effective cooling of the hot components, such as the transition pieces. It must also ensure proper air/fuel mixing in the combustor, hence the combustor exit pattern factor. The overall thermal efficiency of the power plant can be increased by minimizing the total pressure loss in the diffusers associated with the air extraction. Therefore, a study of airflow in the pre- and dump-diffusers with and without air extraction would provide information crucial to attaining high-thermal efficiency and to preventing hot spots. The research group at Clemson University suggested using a Griffith diffuser for the prediffuser and extracting air from the diffuser inlet. The present research establishes that the analytically identified problems in the impingement cooling flow are factual. This phase of the contracted research substantiates experimentally the advantage of using the Griffith diffuser with air extraction at the diffuser inlet.

Technical report writing

Science.gov (United States)

Vidoli, Carol A.

1992-01-01

This manual covers the fundamentals of organizing, writing, and reviewing NASA technical reports. It was written to improve the writing skills of LeRC technical authors and the overall quality of their reports.

VANDAL technical overview

International Nuclear Information System (INIS)

Unsworth, M.D.

1989-07-01

This document is concerned with the technicalities of the VANDAL code and covers the technical details of each of the systems modules in turn. Covered are SAMPLING, FLOW, VAULT, GEOSPHERE, BIOSPHERE and TIMESTEPPING. (author)

LC Data QUEST: A Technical Architecture for Community Federated Clinical Data Sharing.

Science.gov (United States)

Stephens, Kari A; Lin, Ching-Ping; Baldwin, Laura-Mae; Echo-Hawk, Abigail; Keppel, Gina A; Buchwald, Dedra; Whitener, Ron J; Korngiebel, Diane M; Berg, Alfred O; Black, Robert A; Tarczy-Hornoch, Peter

2012-01-01

The University of Washington Institute of Translational Health Sciences is engaged in a project, LC Data QUEST, building data sharing capacity in primary care practices serving rural and tribal populations in the Washington, Wyoming, Alaska, Montana, Idaho region to build research infrastructure. We report on the iterative process of developing the technical architecture for semantically aligning electronic health data in primary care settings across our pilot sites and tools that will facilitate linkages between the research and practice communities. Our architecture emphasizes sustainable technical solutions for addressing data extraction, alignment, quality, and metadata management. The architecture provides immediate benefits to participating partners via a clinical decision support tool and data querying functionality to support local quality improvement efforts. The FInDiT tool catalogues type, quantity, and quality of the data that are available across the LC Data QUEST data sharing architecture. These tools facilitate the bi-directional process of translational research.

Biological exposure assessment to tetrachloroethylene for workers in the dry cleaning industry

Directory of Open Access Journals (Sweden)

Ashley David L

2008-04-01

Full Text Available Abstract Background The purpose of this study was to assess the feasibility of conducting biological tetrachloroethylene (perchloroethylene, PCE exposure assessments of dry cleaning employees in conjunction with evaluation of possible PCE health effects. Methods Eighteen women from four dry cleaning facilities in southwestern Ohio were monitored in a pilot study of workers with PCE exposure. Personal breathing zone samples were collected from each employee on two consecutive work days. Biological monitoring included a single measurement of PCE in blood and multiple measurements of pre- and post-shift PCE in exhaled breath and trichloroacetic acid (TCA in urine. Results Post-shift PCE in exhaled breath gradually increased throughout the work week. Statistically significant correlations were observed among the exposure indices. Decreases in PCE in exhaled breath and TCA in urine were observed after two days without exposure to PCE. A mixed-effects model identified statistically significant associations between PCE in exhaled breath and airborne PCE time weighted average (TWA after adjusting for a random participant effect and fixed effects of time and body mass index. Conclusion Although comprehensive, our sampling strategy was challenging to implement due to fluctuating work schedules and the number (pre- and post-shift on three consecutive days and multiplicity (air, blood, exhaled breath, and urine of samples collected. PCE in blood is the preferred biological index to monitor exposures, but may make recruitment difficult. PCE TWA sampling is an appropriate surrogate, although more field intensive. Repeated measures of exposure and mixed-effects modeling may be required for future studies due to high within-subject variability. Workers should be monitored over a long enough period of time to allow the use of a lag term.

Socio-technical Betwixtness

DEFF Research Database (Denmark)

Bossen, Claus

2017-01-01

the intrinsically social and technical interwovenness of design, and the necessity of including affected people and stakeholders in the design process. This betwixtness of socio-technical design is demonstrated by the analysis of two IT systems for healthcare: a foundational model for electronic healthcare records......This chapter focusses on two challenges for socio-technical design: Having to choose between different rationales for design, and the adequate understanding and depiction of the work to be redesigned. These two challenges betwixt the otherwise strong tenets of socio-technical design of pointing out......, and an IT system organizing hospital porters’ work. The conceptual background for the analysis of the cases is provided by a short introduction to different rationales for organizational design, and by pointing to the differences between a linear, rationalistic versus an interactional depiction of work....

Exploring the relationship between anaesthesiologists' non-technical and technical skills

DEFF Research Database (Denmark)

Gjeraa, K; Jepsen, R M H G; Rewers, M

2016-01-01

BACKGROUND: A combination of non-technical skills (NTS) and technical skills (TS) is crucial for anaesthetic patient management. However, a deeper understanding of the relationship between these two skills remains to be explored. We investigated the characteristics of trainee anaesthesiologists...... the customised version of the Anaesthetists' Non-Technical Skills System, ANTSdk, and an adapted TS checklist for calculating the correlation between NTS and TS. Written descriptions of the observed NTS were analysed using directed content analysis. RESULTS: The correlation between the NTS and the TS ratings......, concrete NTS were developed to aid the understanding, training and use of NTS....

Preparation and flow characteristic of a novel phase change fluid for latent heat transfer

Energy Technology Data Exchange (ETDEWEB)

Zou, Deqiu [Marine College of Ningbo University, Ningbo 315211, Zhejiang (China); Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou 510640 (China); Feng, Ziping; Xiao, Rui; Qin, Kun; Zhang, Jianjun; Song, Wenji; Tu, Qiu [Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou 510640 (China)

2010-12-15

A novel phase change emulsion (PCE) was prepared and its latent heat was measured by DSC. To analyze its feasibility in heat transportation through a piping system, an experimental system was built. The pressure drop of the PCE for turbulent flow was measured and the effects of such facts as the paraffin concentration and flow velocity were discussed. According to the pressure characteristic and latent heat of the PCE, the pumping power consumption rates of PCE to water under the same pipe diameter and a given heat transportation quantity can be obtained. The results show that mass flow rate and pumping power consumption of the PCE decrease greatly compared with water. For example, the decrease can be up to about 73% at V=0.6 m/s (20 and 30 wt%). Furthermore, the results show that PCE of 20 wt% can obtain almost the same pumping power consumption savings as PCE of 30 wt% in a certain flow velocity range. Finally, the applications of the PCE in the area of waste heat usage, electrical boiler and solar energy usage were commented. (author)

Learning non-technical skill lessons from testimony given in the investigation of the nuclear accident at the Fukushima Nuclear Power Stations

International Nuclear Information System (INIS)

Hikono, Masaru; Sakuda, Hiroshi; Matsui, Yuko; Goto, Manabu; Kanayama, Masaki

2016-01-01

The Government Investigation Committee on the Accident at the Fukushima Nuclear Power Stations interviewed individuals concerned. The hearing records, published in 2014, are considered to have valuable lessons for power station managers who encounter severe accidents. In this study, descriptions from the hearing records were extracted as lessons for managers. The extractions were classified by the subject (for whom the lessons are intended), and the category of the non-technical skills. The results showed the possibility of pointing out the lessons in accordance with responsibilities. (author)

High-performance ternary blend polymer solar cells involving both energy transfer and hole relay processes.

Science.gov (United States)

Lu, Luyao; Chen, Wei; Xu, Tao; Yu, Luping

2015-06-04

The integration of multiple materials with complementary absorptions into a single junction device is regarded as an efficient way to enhance the power conversion efficiency (PCE) of organic solar cells (OSCs). However, because of increased complexity with one more component, only limited high-performance ternary systems have been demonstrated previously. Here we report an efficient ternary blend OSC with a PCE of 9.2%. We show that the third component can reduce surface trap densities in the ternary blend. Detailed studies unravel that the improved performance results from synergistic effects of enlarged open circuit voltage, suppressed trap-assisted recombination, enhanced light absorption, increased hole extraction, efficient energy transfer and better morphology. The working mechanism and high device performance demonstrate new insights and design guidelines for high-performance ternary blend solar cells and suggest that ternary structure is a promising platform to boost the efficiency of OSCs.

Extracts from technical journals

Directory of Open Access Journals (Sweden)

Soria Santamaría, F.

1976-12-01

Full Text Available Not avaiableSe estudia, a través de los espectros de absorción IR, la hidratación del cemento portland hasta 28 días, considerando como variables su contenido de yeso y la dosis de cloruro cálcico añadida en el agua de amasado. Se comprueba la idoneidad de la técnica, la cual permite observar hechos diferenciales, en función de las variables consideradas. Se puede apreciar una acción antagónica entre el efecto retardador normal del yeso en el fraguado y en la hidratación, y el efecto acelerador del cloruro cálcico, a las dosis y concentraciones en que se produce. Las acciones retardadoras, tanto del yeso como del cloruro cálcico a baja concentración (1% respecto del cemento anhidro, o menor, se atribuyen a la formación predominante de ettringita, mientras que las acciones aceleradoras se explican por la formación preferente de monosulfo-aluminato, cloroaluminato y aluminato tricálcico hidratados. Las conclusiones del trabajo confirman y amplían las previas de otros autores, relativos a aspectos cualitativos y cuantitativos de la influencia del yeso y del cloruro cálcico en las propiedades y en el comportamiento del cemento en la hidratación, así como referentes al mecanismo de ésta.

Synergistic effect of nano-sized mackinawite with cyano-cobalamin in cement slurries for reductive dechlorination of tetrachloroethylene

International Nuclear Information System (INIS)

Kyung, Daeseung; Sihn, Youngho; Kim, Sangwoo; Bae, Sungjun; Amin, Muhammad Tahir; Alazba, Abdulrahman Ali; Lee, Woojin

2016-01-01

Highlights: • Complete degradation of PCE was observed in nFeS-Cbl(III)-cement at pH 12. • PCE was completely degraded to non-chlorinated organic compounds by this system. • Co redox couple and Ca species in cement played a pivotal role for PCE reduction. • Increases in Cbl(III) concentration, cement ratio, and pH enhanced PCE degradation. • Efficiency of the system for PCE reduction was good even at high concentration of PCE. - Abstract: Experiments were conducted to investigate the reductive dechlorination of tetrachloroethylene (PCE) by nano-Mackinawite (nFeS) with cyano-cobalamin (Cbl(III)) in cement slurries. Almost complete degradation of PCE by nFeS-Cbl(III) was observed in cement slurries in 5 h and its degradation kinetics (k_o_b_s_-_P_C_E = 0.57 h"−"1) was 6-times faster than that of nFeS-Cbl(III) without the cement slurries. PCE was finally transformed to non-chlorinated organic compounds such as ethylene, acetylene, and C3-C4 hydrocarbons by nFeS-Cbl(III) in cement slurries. X-ray photoelectron spectroscopy and PCE degradation by cement components (SiO_2, Al_2O_3, and CaO) revealed that both the reduced Co species in Cbl(III) and the presence of Ca in cement played an important role for the enhanced reductive dechlorination of PCE. The increase in the concentration of Cbl(III) (0.005–0.1 mM), cement ratio (0.05–0.2), and suspension pH (11.5–13.5) accelerated the PCE degradation kinetics by providing more favorable environments for the production of reactive Ca species and reduction of Co species. We also observed that the degradation efficiency of PCE by nFeS-Cbl(III)-cement lasted even at high concentration of PCE. The experimental results obtained from this study could provide fundamental knowledge of redox interactions among nFeS, Cbl(III), and cement, which could significantly enhance reductive dechlorination of chlorinated organics in contaminated natural and engineered environments.

Report on the basic design of the FY 1998 technical information database; 1998 nendo gijutsu joho database no kihon sekkei hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of promoting the effective transfer of the results of technical development and the technical information distribution, study and basic design were conducted of a concept of the new technical database run by NEDO. In the study, the following were conducted to extract the subjects: analysis of examples of project databases such as CADDET, scientific technology research information (JCLEARING), evaluation/survey of the present situation of database users, etc. In the study of a concept of technical information database, clarified were the classification of information, definition of the details, finding-out of relations between various kinds of information, mechanism of collection/processing/storage/dispatch/exchange of information, role of NEDO, etc. In the basic design, as the NEDO technical information database viable for the moment, the rough design was conducted of the project information, information on result reports, and information on research institutes. Further, to handle in unity the database controlled in different method, studied were the applicability to the project database of the general combined concept, advantages, restricted items, etc. (NEDO)

CONVERSION EXTRACTION DESULFURIZATION (CED) PHASE III

Energy Technology Data Exchange (ETDEWEB)

James Boltz

2005-03-01

This project was undertaken to refine the Conversion Extraction Desulfurization (CED) technology to efficiently and economically remove sulfur from diesel fuel to levels below 15-ppm. CED is considered a generic term covering all desulfurization processes that involve oxidation and extraction. The CED process first extracts a fraction of the sulfur from the diesel, then selectively oxidizes the remaining sulfur compounds, and finally extracts these oxidized materials. The Department of Energy (DOE) awarded Petro Star Inc. a contract to fund Phase III of the CED process development. Phase III consisted of testing a continuous-flow process, optimization of the process steps, design of a pilot plant, and completion of a market study for licensing the process. Petro Star and the Degussa Corporation in coordination with Koch Modular Process Systems (KMPS) tested six key process steps in a 7.6-centimeter (cm) (3.0-inch) inside diameter (ID) column at gas oil feed rates of 7.8 to 93.3 liters per hour (l/h) (2.1 to 24.6 gallons per hour). The team verified the technical feasibility with respect to hydraulics for each unit operation tested and successfully demonstrated pre-extraction and solvent recovery distillation. Test operations conducted at KMPS demonstrated that the oxidation reaction converted a maximum of 97% of the thiophenes. The CED Process Development Team demonstrated that CED technology is capable of reducing the sulfur content of light atmospheric gas oil from 5,000-ppm to less than 15-ppm within the laboratory scale. In continuous flow trials, the CED process consistently produced fuel with approximately 20-ppm of sulfur. The process economics study calculated an estimated process cost of $5.70 per product barrel. The Kline Company performed a marketing study to evaluate the possibility of licensing the CED technology. Kline concluded that only 13 refineries harbored opportunity for the CED process. The Kline study and the research team's discussions

Investigation of pharmaceuticals and medical devices containing 90Y extracted from high radioactive liquid waste in spent-fuel reprocessing

International Nuclear Information System (INIS)

Hosoma, Takashi

2012-07-01

Pharmaceuticals and medical devices containing radioactive 90 Y are realized, approved and placed on the international market where three products are available in Europe and the United States, and one product in Japan. These products are used not for diagnosis but for treatment by internal irradiation. It was estimated from the deliberative report of the approval in Japan that 90 Y was extracted in Europe from high radioactive liquid waste (HALW) yielded in spent-fuel reprocessing. In this report, products placed on the market and physical properties were reviewed, reasons of the realization and conditions to realize succeeding products were estimated, extraction method was compared with other methods, technical subjects, and relevant regulations were investigated. Although a medical device containing radioactive 90 Y has been studied in Japan and one pharmaceutical product was approved, a breakthrough would be necessary to put 90 Y utilization beyond alternative treatments. The breakthrough would become be promising; for example, if conventional treatments could be supported by technical development to deliver 90 Y more sharply to the target with shorter serum half-life. Extraction of 90 Y nuclide from HALW has advantages over thermal neutron irradiation of natural nuclide, a system is envisioned where 90 Sr as a parent nuclide is separated in the reprocessing then transported to and stored in a factory of radiopharmaceuticals followed by 90 Y extraction on demand. (author)

Figures and First Years: An Analysis of Calculus Students' Use of Figures in Technical Reports

Directory of Open Access Journals (Sweden)

Nathan J. Antonacci

2017-07-01

Full Text Available This three-year study focused on first-year Calculus I students and their abilities to incorporate figures in technical reports. In each year, these calculus students wrote a technical report as part of the Polar Bear Module, an educational unit developed for use in partner courses in biology, computer science, mathematics, and physics as part of the Multidisciplinary Sustainability Education (MSE project at Ithaca College. In the first year of the project, students received basic technical report guidelines. In year two, the report guidelines changed to include explicit language on how to incorporate figures. In year three, a grading rubric was added to the materials provided to one of the two classes. In all three years, the students performed below expectations in their use of graphs in their reports. Reviews of the figures in the 78 technical reports written by the 106 students showed repeated deficiencies in the figures and how the students used them in the discussion sections and in evidence-based arguments. In year three the student’s quantitative literacy (QL skills were assessed using an extract from a QL assessment instrument published in Numeracy. The results indicated that the students could both read and interpret figures, suggesting that issues with QL were not the main contributor to student difficulty with written discussion about graphs. The study underscores the need that explicit instructional attention be given to developing student knowhow in the use of figures in technical reports.

Effect of polycarboxylate ether comb-type polymer on viscosity and interfacial properties of kaolinite clay suspensions.

Science.gov (United States)

Zhang, Ling; Lu, Qingye; Xu, Zhenghe; Liu, Qingxia; Zeng, Hongbo

2012-07-15

The interactions between kaolinite clay particles and a comb-type polymer (polycarboxylate ether or PCE), so-called PCE super-plasticizer, were investigated through viscosity and surface forces measurements by a rheometer and a Surface Forces Apparatus (SFA). The addition of PCE shows a strong impact on the viscosity of concentrated kaolinite suspensions in alkaline solutions (pH=8.3) but a weak effect under acidic conditions (pH=3.4). In acidic solutions, the high viscosity measured is attributed to the strong electrostatic interaction between negatively charged basal planes and positively charged edge surfaces of clay particles. Under the alkaline condition, the suspension viscosity was found to first increase significantly and then decrease with increasing PCE dosages. The results from surface forces measurement show that PCE molecules at low dosages can bridge the kaolinite particles in the concentrated suspensions via hydrogen bonding, leading to the formation of a kaolinite-PCE "network" and hence an increased suspension viscosity. At high PCE dosages, clay particles are fully covered by PCE molecules, leading to a more dispersed kaolinite suspensions and hence lower suspension viscosity due to steric repulsion between the adsorbed PCE molecules. The insights derived from measuring viscosity and interfacial properties of kaolinite suspensions containing varying amount of comb-type super-plasticizer PCE at different pH provide the foundation for many engineering applications and optimizing industrial processes. Copyright © 2012 Elsevier Inc. All rights reserved.

Technical Agency in Practice

DEFF Research Database (Denmark)

Krummheuer, Antonia Lina

2015-01-01

) description of hybrid networks in which human and non-human actants are granted agency without differentiating different kinds of agency, EMCA focuses on the member's perspectives and the situated construction of technical agency that is made relevant within an ongoing interaction. Based on an EMCA analysis......The paper combines the discussion of technical agency and hybrid networks of Actor-Network Theory (ANT) with an ethnomethodological/conversation analytical (EMCA) perspective on situated practices in which participants ascribe agency to technical artefacts. While ANT works with (ethnographic...... of three video recordings of situations in which technical agency is made relevant by the human participants, the paper demonstrates different ways in which agency is granted to technical artefacts. Human participants can treat a technology as communication partner, as an active part (and actant...

Relationship between non-technical skills and technical performance during cardiopulmonary resuscitation: does stress have an influence?

Science.gov (United States)

Krage, Ralf; Zwaan, Laura; Tjon Soei Len, Lian; Kolenbrander, Mark W; van Groeningen, Dick; Loer, Stephan A; Wagner, Cordula; Schober, Patrick

2017-11-01

Non-technical skills, such as task management, leadership, situational awareness, communication and decision-making refer to cognitive, behavioural and social skills that contribute to safe and efficient team performance. The importance of these skills during cardiopulmonary resuscitation (CPR) is increasingly emphasised. Nonetheless, the relationship between non-technical skills and technical performance is poorly understood. We hypothesise that non-technical skills become increasingly important under stressful conditions when individuals are distracted from their tasks, and investigated the relationship between non-technical and technical skills under control conditions and when external stressors are present. In this simulator-based randomised cross-over study, 30 anaesthesiologists and anaesthesia residents from the VU University Medical Center, Amsterdam, the Netherlands, participated in two different CPR scenarios in random order. In one scenario, external stressors (radio noise and a distractive scripted family member) were added, while the other scenario without stressors served as control condition. Non-technical performance of the team leader and technical performance of the team were measured using the 'Anaesthetists' Non-technical Skill' score and a recently developed technical skills score. Analysis of variance and Pearson correlation coefficients were used for statistical analyses. Non-technical performance declined when external stressors were present (adjusted mean difference 3.9 points, 95% CI 2.4 to 5.5 points). A significant correlation between non-technical and technical performance scores was observed when external stressors were present (r=0.67, 95% CI 0.40 to 0.83, ptechnical performance score (task management, team working, situation awareness, decision-making). During CPR with external stressors, the team's technical performance is related to the non-technical skills of the team leader. This may have important implications for training of

Selective accumulation of 147Pm in organism on induction of PCE's micronucleus and SCE of bone marrow cells as well as the chromosome aberrations on fetal liver and spleen

International Nuclear Information System (INIS)

Zhu Shoupeng; Zheng Siying; Wang Liuyi; Lu Zhongyan; Yang Shuqin

1989-01-01

Study of accumulation peculiarity of 147 Pm showed that I.V. different doses of 147 Pm were the same selectively localized in skeleton and liver. Retention of 147 Pm in skeleton and liver was elevated when the radioactive doses of 147 Pm were increased. At the same time absorption does of 147 Pm radiation was heightened. The ability of 147 Pm to induce sister chromatid exchanges (SCEs) has been investigated by IdU labelling methods. A statistically significant elevation of SCEs was observed after 147 Pm intake.In mice the number of SCEs per cell in bone marrow cells was always higher when the animals were maintained on the doses of 37 Bq/g. The injurious effects of 147 Pm, using PCE's micronucleus rates in bone marrow cells were observed. 147 Pm was dominantly deposited on maternal liver. Deposition of 147 Pm in maternal spleen was about quandrantal of the maternal liver. Studies indicated that maternal contamination of 147 Pm could induced chromosome aberrations in fetal liver and spleen cells. Among the type of aberrations induced by 147 Pm, chromatid breakage were predominant. The incidence of chromosome aberrations on fetal liver cells induced by 147 Pm was higher on fetal spleen cells

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Glasser, Alan H. [Fusion Theory and Computation Inc., Kingston, WA (United States)

2018-02-02

Final technical report on DE-SC0016106. This is the final technical report for a portion of the multi-institutional CEMM project. This report is centered around 3 publications and a seminar presentation, which have been submitted to E-Link.

Technical noise supplement : TeNS : a technical supplement to the Traffic Noise Analysis Protocol.

Science.gov (United States)

1998-10-01

The purpose of this Technical Noise Supplement (TeNS) is to provide technical background : information on transportation-related noise in general and highway traffic noise in : particular. It is designed to elaborate on technical concepts and procedu...

Writing a technical note.

Science.gov (United States)

Ng, K H; Peh, W C G

2010-02-01

A technical note is a short article giving a brief description of a specific development, technique or procedure, or it may describe a modification of an existing technique, procedure or device applicable to medicine. The technique, procedure or device described should have practical value and should contribute to clinical diagnosis or management. It could also present a software tool, or an experimental or computational method. Technical notes are variously referred to as technical innovations or technical developments. The main criteria for publication will be the novelty of concepts involved, the validity of the technique and its potential for clinical applications.

Technical Elements (CCT1)

DEFF Research Database (Denmark)

Thomsen, Kirsten Engelund; Wittchen, Kim Bjarne

2017-01-01

Many of the aspects dealt with in the CA EPBD are closely interlinked with each other and may refer to both new and existing buildings, as well as to inspection and certification. This is also true for technical aspects, such as the calculation methodologies, and how to include technical systems......’ efficiency or how to integrate renewable energy within them. The central team for Technical Elements deals with issues of a technical nature, which are common to new and existing buildings, and/or with minimum demands, certification and inspection. This report focuses on the implementation of Articles 3, 4...

Towards technical interoperability in telemedicine.

Energy Technology Data Exchange (ETDEWEB)

Craft, Richard Layne, II

2004-05-01

For telemedicine to realize the vision of anywhere, anytime access to care, the question of how to create a fully interoperable technical infrastructure must be addressed. After briefly discussing how 'technical interoperability' compares with other types of interoperability being addressed in the telemedicine community today, this paper describes reasons for pursuing technical interoperability, presents a proposed framework for realizing technical interoperability, identifies key issues that will need to be addressed if technical interoperability is to be achieved, and suggests a course of action that the telemedicine community might follow to accomplish this goal.

Avaliação técnica do trator florestal arrastador "skidder" com diferentes tipos de rodados na extração de madeira em povoamentos de pinus Technical evalution of a skidder with different wheeled types in log extraction activies of pine plantation

Directory of Open Access Journals (Sweden)

Eduardo da Silva Lopes

2007-12-01

Full Text Available Este trabalho teve como principal objetivo a avaliação técnica das atividades de extração de madeira usando tratores florestais arrastadores skidders equipados com rodado de pneus e com rodado de pneus recoberto com semi-esteiras. A avaliação técnica consistiu em determinar os índices de produtividade da operação de extração da madeira por meio de um estudo de tempos e movimentos, em que a operação foi dividida em fases do ciclo de trabalho. Foram determinadas as produtividades das máquinas em diferentes situações de distâncias de extração e declividades de terreno. Os resultados indicaram que o tempo médio do ciclo operacional do skidder com rodado de pneus foi 7,1% menor em relação ao skidder de pneus recobertos por esteiras, o que explicado se pela maior eficiência dos pneus sobre a superfície do terreno. O skidder de pneus apresentou melhor eficiência na situação de declividade entre 10 e 20%, devido à maior agilidade do rodado de pneus e capacidade em desenvolver maior velocidade, enquanto o skidder com rodado de pneus recoberto por esteiras apresentou velocidade operacional constante. Em declividade acima de 20%, o skidder de pneus recoberto com esteiras realizou normalmente o arraste da madeira, enquanto o skidder de pneus não entrou em operação devido à elevada patinagem dos pneus e diminuição da capacidade de tração.The objective of this study was to evaluate technical log extraction activities using a skidder with tires and a skidder with tracks over the tires. Technical evaluation consisted in determining log extraction productivity indexes based on motion and time study, in which the extraction activities were grouped into work cycle phases. Machine productivity was determined in different extraction distances and slope degree situations. The results showed that the operational cycle average time of the tire skidder was 7.1% smaller that the skidder with tracks over the tires, explained by the

Towards a Moral Ecology of Pharmacological Cognitive Enhancement in British Universities.

Science.gov (United States)

Vagwala, Meghana Kasturi; Bicquelet, Aude; Didziokaite, Gabija; Coomber, Ross; Corrigan, Oonagh; Singh, Ilina

2017-01-01

Few empirical studies in the UK have examined the complex social patterns and values behind quantitative estimates of the prevalence of pharmacological cognitive enhancement (PCE). We conducted a qualitative investigation of the social dynamics and moral attitudes that shape PCE practices among university students in two major metropolitan areas in the UK. Our thematic analysis of eight focus groups ( n  = 66) suggests a moral ecology that operates within the social infrastructure of the university. We find that PCE resilience among UK university students is mediated by normative and cultural judgments disfavoring competitiveness and prescription drug taking. PCE risk can be augmented by social factors such as soft peer pressure and normalization of enhancement within social and institutional networks. We suggest that moral ecological dynamics should be viewed as key mechanisms of PCE risk and resilience in universities. Effective PCE governance within universities should therefore attend to developing further understanding of the moral ecologies of PCE.

Separation of uranium from molybdenum by alkyl phosphoric acid extraction

Energy Technology Data Exchange (ETDEWEB)

Zhongshi, Li

1986-08-01

The regularities of separation of uranium from molybdenum by alkyl phosphoric acid extraction are described. Two parameters, i.e., density ratio of uranium to molybdenum in organic phase at first stage and density of uranium in raffinate at last stage are presented. The relationship between these parameters and purity of molybdenum and uranium products is given. The method of adjusting and controlling these parameters in experiments and production is worked out. The technical key problem in comprehensive utilization of sedimentary type uranium ore containing molybdenum with close concentration of these to elements has been solved.

Schmidt-Kalman Filter with Polynomial Chaos Expansion for Orbit Determination of Space Objects

Science.gov (United States)

Yang, Y.; Cai, H.; Zhang, K.

2016-09-01

Parameter errors in orbital models can result in poor orbit determination (OD) using a traditional Kalman filter. One approach to account for these errors is to consider them in the so-called Schmidt-Kalman filter (SKF), by augmenting the state covariance matrix (CM) with additional parameter covariance rather than additively estimating these so-called "consider" parameters. This paper introduces a new SKF algorithm with polynomial chaos expansion (PCE-SKF). The PCE approach has been proved to be more efficient than Monte Carlo method for propagating the input uncertainties onto the system response without experiencing any constraints of linear dynamics, or Gaussian distributions of the uncertainty sources. The state and covariance needed in the orbit prediction step are propagated using PCE. An inclined geosynchronous orbit scenario is set up to test the proposed PCE-SKF based OD algorithm. The satellite orbit is propagated based on numerical integration, with the uncertain coefficient of solar radiation pressure considered. The PCE-SKF solutions are compared with extended Kalman filter (EKF), SKF and PCE-EKF (EKF with PCE) solutions. It is implied that the covariance propagation using PCE leads to more precise OD solutions in comparison with those based on linear propagation of covariance.

Enhanced photovoltaic performance of CH3NH3PbBrXI3-X-based perovskite solar cells via anti-solvent extraction

Science.gov (United States)

Jiang, Zhaoyi; Zhang, Weijia; Lu, Chaoqun; Ma, Denghao; Liu, Haixu; Yu, Wei; Zhang, Yu; Ma, Qiang; Zhang, Yulong

2018-06-01

In this paper, the two-step sequential deposition method was used to prepare the CH3NH3PbBrXI3-X films by introducing CH3NH3Br in the precursors. The surface morphology of the PbI2 films was controlled by anti-solvent extraction (ASE) to improve the microstructure and photo-physical properties of the perovskite films. It was noteworthy that, compared to the compact PbI2 films, the porous PbI2 films facilitated the growth of crystals and bromine incorporation in films, and the prepared perovskite films exhibited enlarged grain size, increased light absorption, enhanced Br incorporation and prolonged carrier lifetime, which resulted in excellent photo-electrical properties of the CH3NH3PbBrXI3-X films. With porous PbI2 templates, the inverted planar perovskite solar cells based on films with appropriate Br incorporation (CH3NH3Br/CH3NH3I mole ratio = 3/7) showed a photovoltaic conversion efficiency (PCE) of 14.9%, and the stability of the devices in air was elevated. Consequently, the high-quality CH3NH3PbBrXI3-X films can be obtained with porous PbI2 templates for improving the performance of the perovskite solar cells.

Anaerobic degradation of tetrachloroethylene; Anaerober Abbau von Tetrachlorethylen

Energy Technology Data Exchange (ETDEWEB)

Diekert, G. [Stuttgart Univ. (Germany). Inst. fuer Mikrobiologie; Scholz-Muramatsu, H. [Stuttgart Univ. (Germany). Inst. fuer Siedlungswasserbau

1996-12-31

Dehalospirillum multivorans, a tetrachloroethylene-dechlorinating bacterium, was isolated in activated sludge. This organism is able to grow on a defined medium with hydrogen and tetrachloroethylene (PCE) as its only energy source. The organism was characterised and the physiology of dechlorination was studied. In this process PCE is dechlorinated to cis-1,2-dichloroethene (DCE) via trichloroethene (TCE). A fluidized-bed reactor which reduces PCE to DCE at a high rate (15 nmol/min/mg of protein at 5 {mu}M PCE) was inoculated with the bacterium. Meanwhile a reactor inoculated with D. multivorans and a fully dechlorinating mixed culture has become available which catalyses the complete dechlorination of PCE to ethene at just as high rates. Tetrachloroethene dehalogenase was purified from D. multivorans (unpublished results) and characterised. (orig./SR) [Deutsch] Aus Belebtschlamm wurde ein Tetrachlorethen-dechlorierendes Bakterium, Dehalospirillum multivorans, isoliert. Der Organismus waechst auf definiertem Medium mit Wasserstoff und Tetrachlorethen (PCE) als einziger Energiequelle. Der Organismus wurde charakterisiert und die Physiologie der Dechlorierung wurde untersucht. PCE wird dabei ueber Trichlorethen (TCE) bis zum cis-1,2-Dichlorethen (DCE) dechloriert. Mit diesem Bakterium wurde ein Wirbelschichtreaktor inokuliert, der mit hohen Raten (15 nmol/min/mg Protein bei 5 {mu}M PCE) PCE zu DCE reduziert. Inzwischen steht ein Reaktor zur Verfuegung, der mit D. multivorans und einer voellig dechlorierenden Mischkultur inokuliert wurde und der mit ebenso hohen Raten eine vollstaendige Dechlorierung von PCE bis zum Ethen katalysiert. Aus D. multivorans wurde die Tetrachlorethen-Dehalogenase gereinigt (unveroeffentlichte Ergebnisse) und charakterisiert. (orig./SR)

Anaerobic degradation of tetrachloroethylene; Anaerober Abbau von Tetrachlorethylen

Energy Technology Data Exchange (ETDEWEB)

Diekert, G [Stuttgart Univ. (Germany). Inst. fuer Mikrobiologie; Scholz-Muramatsu, H [Stuttgart Univ. (Germany). Inst. fuer Siedlungswasserbau

1997-12-31

Dehalospirillum multivorans, a tetrachloroethylene-dechlorinating bacterium, was isolated in activated sludge. This organism is able to grow on a defined medium with hydrogen and tetrachloroethylene (PCE) as its only energy source. The organism was characterised and the physiology of dechlorination was studied. In this process PCE is dechlorinated to cis-1,2-dichloroethene (DCE) via trichloroethene (TCE). A fluidized-bed reactor which reduces PCE to DCE at a high rate (15 nmol/min/mg of protein at 5 {mu}M PCE) was inoculated with the bacterium. Meanwhile a reactor inoculated with D. multivorans and a fully dechlorinating mixed culture has become available which catalyses the complete dechlorination of PCE to ethene at just as high rates. Tetrachloroethene dehalogenase was purified from D. multivorans (unpublished results) and characterised. (orig./SR) [Deutsch] Aus Belebtschlamm wurde ein Tetrachlorethen-dechlorierendes Bakterium, Dehalospirillum multivorans, isoliert. Der Organismus waechst auf definiertem Medium mit Wasserstoff und Tetrachlorethen (PCE) als einziger Energiequelle. Der Organismus wurde charakterisiert und die Physiologie der Dechlorierung wurde untersucht. PCE wird dabei ueber Trichlorethen (TCE) bis zum cis-1,2-Dichlorethen (DCE) dechloriert. Mit diesem Bakterium wurde ein Wirbelschichtreaktor inokuliert, der mit hohen Raten (15 nmol/min/mg Protein bei 5 {mu}M PCE) PCE zu DCE reduziert. Inzwischen steht ein Reaktor zur Verfuegung, der mit D. multivorans und einer voellig dechlorierenden Mischkultur inokuliert wurde und der mit ebenso hohen Raten eine vollstaendige Dechlorierung von PCE bis zum Ethen katalysiert. Aus D. multivorans wurde die Tetrachlorethen-Dehalogenase gereinigt (unveroeffentlichte Ergebnisse) und charakterisiert. (orig./SR)

Enhancement effects of reducing agents on the degradation of tetrachloroethene in the Fe(II)/Fe(III) catalyzed percarbonate system

International Nuclear Information System (INIS)

Miao, Zhouwei; Gu, Xiaogang; Lu, Shuguang; Brusseau, Mark L.; Yan, Ni; Qiu, Zhaofu; Sui, Qian

2015-01-01

Highlights: • PCE degradation by reducing-agent modified Fe-catalyzed percarbonate was studied. • The addition of reducing agents significantly increased PCE degradation. • Hydroxylamine hydrochloride showed the best effect on enhancing PCE degradation. • The primary PCE degradation mechanism was oxidation by hydroxyl radical. • O_2·"− participated in the degradation of PCE in reducing-agent modified system. - Abstract: In this study, the effects of reducing agents on the degradation of tetrachloroethene (PCE) were investigated in the Fe(II)/Fe(III) catalyzed sodium percarbonate (SPC) system. The addition of reducing agents, including hydroxylamine hydrochloride, sodium sulfite, ascorbic acid and sodium ascorbate, accelerated the Fe(III)/Fe(II) redox cycle, leading to a relatively steady Fe(II) concentration and higher production of free radicals. This, in turn, resulted in enhanced PCE oxidation by SPC, with almost complete PCE removal obtained for appropriate Fe and SPC concentrations. The chemical probe tests, using nitrobenzene and carbon tetrachloride, demonstrated that HO· was the predominant radical in the system and that O_2·"− played a minor role, which was further confirmed by the results of electron spin resonance measurements. PCE degradation decreased significantly with the addition of isopropanol, a HO· scavenger, supporting the hypothesis that HO· was primarily responsible for PCE degradation. It is noteworthy that Cl"− release was slightly delayed in the first 20 min, indicating that intermediate products were produced. However, these intermediates were further degraded, resulting in the complete conversion of PCE to CO_2. In conclusion, the use of reducing agents to enhance Fe(II)/Fe(III) catalyzed SPC oxidation appears to be a promising approach for the rapid degradation of organic contaminants in groundwater.

Enhancement effects of reducing agents on the degradation of tetrachloroethene in the Fe(II)/Fe(III) catalyzed percarbonate system

Energy Technology Data Exchange (ETDEWEB)

Miao, Zhouwei [State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, East China University of Science and Technology, Shanghai 200237 (China); Soil, Water and Environmental Science Department, School of Earth and Environmental Sciences, The University of Arizona, 429 Shantz Building, Tucson, AZ 85721 (United States); Gu, Xiaogang [State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, East China University of Science and Technology, Shanghai 200237 (China); Lu, Shuguang, E-mail: lvshuguang@ecust.edu.cn [State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, East China University of Science and Technology, Shanghai 200237 (China); Brusseau, Mark L. [Soil, Water and Environmental Science Department, School of Earth and Environmental Sciences, The University of Arizona, 429 Shantz Building, Tucson, AZ 85721 (United States); Yan, Ni [Hydrology and Water Resources Department, School of Earth and Environmental Sciences, University of Arizona, 429 Shantz Building, Tucson, AZ 85721 (United States); Qiu, Zhaofu; Sui, Qian [State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, East China University of Science and Technology, Shanghai 200237 (China)

2015-12-30

Highlights: • PCE degradation by reducing-agent modified Fe-catalyzed percarbonate was studied. • The addition of reducing agents significantly increased PCE degradation. • Hydroxylamine hydrochloride showed the best effect on enhancing PCE degradation. • The primary PCE degradation mechanism was oxidation by hydroxyl radical. • O{sub 2}·{sup −} participated in the degradation of PCE in reducing-agent modified system. - Abstract: In this study, the effects of reducing agents on the degradation of tetrachloroethene (PCE) were investigated in the Fe(II)/Fe(III) catalyzed sodium percarbonate (SPC) system. The addition of reducing agents, including hydroxylamine hydrochloride, sodium sulfite, ascorbic acid and sodium ascorbate, accelerated the Fe(III)/Fe(II) redox cycle, leading to a relatively steady Fe(II) concentration and higher production of free radicals. This, in turn, resulted in enhanced PCE oxidation by SPC, with almost complete PCE removal obtained for appropriate Fe and SPC concentrations. The chemical probe tests, using nitrobenzene and carbon tetrachloride, demonstrated that HO· was the predominant radical in the system and that O{sub 2}·{sup −} played a minor role, which was further confirmed by the results of electron spin resonance measurements. PCE degradation decreased significantly with the addition of isopropanol, a HO· scavenger, supporting the hypothesis that HO· was primarily responsible for PCE degradation. It is noteworthy that Cl{sup −} release was slightly delayed in the first 20 min, indicating that intermediate products were produced. However, these intermediates were further degraded, resulting in the complete conversion of PCE to CO{sub 2}. In conclusion, the use of reducing agents to enhance Fe(II)/Fe(III) catalyzed SPC oxidation appears to be a promising approach for the rapid degradation of organic contaminants in groundwater.

Study of the picture change error at the 2nd order Douglas Kroll Hess level of theory. Electron and spin density and structure factors of the Bis[bis(methoxycarbimido) aminato] copper (II) complex

International Nuclear Information System (INIS)

Bučinský, Lukáš; Biskupič, Stanislav; Jayatilaka, Dylan

2012-01-01

Graphical abstract: The dependence of the radial distribution of the spin density in the vicinity of the nucleus on the formal oxidation state of the copper atom is shown on the top three figures. Note also the large impact of PCE as well as relativistic effects. The bottom three figures present the relativistic effects and PCE in the electron density of the [CuL 2 ] model compound (of the size 1 bohr 2 ). PCE is very little affecting the relativistic effects in the electron density close to the nucleus of copper atom, i.e. the PCE in the relativistic effects of the electron density are hardly discernable in the case of compounds containing copper. Highlights: ► The extent of PCE in a model compound containing copper atom is presented. ► The spin/electron density along bond the Cu–N is the most affected by PCE only at the nucleus of the copper atom. ► The 2D inspection of relativistic effects in electron/spin densities is not sensitive to PCE. ► Structure factors are an order of magnitude less affected by PCE than by relativistic effects. ► PCE in the Mulliken populations and spin contamination is considered. - Abstract: The analytic correction and the extent of the picture change error (PCE) at the scalar 2nd order Douglas–Kroll–Hess level of theory is considered. The one-dimensional (1D), two-dimensional (2D) spin/electron densities and/or difference densities, structure factors and Mulliken populations of the Bis [bis-(methoxycarbimido) aminato] copper (II) model compound are presented. For further comparison the radial distributions of the electron and spin density of the copper atom (as well as of the copper di-cation) are presented. In addition, the infinite order two component (IOTC) radial distributions of electron and spin density of the copper atom and copper dication are presented as well. The PCE is almost hidden in the 2D densities of the studied model compound. The 1D electron/spin difference densities along the Cu–N bond show the

Ethanol production by extractive fermentation - Process development and technology transfer

International Nuclear Information System (INIS)

Daugulis, A.J.; Axford, D.B.; Mau, T.K.

1991-01-01

Extractive Fermentation is an ethanol processing strategy in which the operations of fermentation and product recovery are integrated and undertaken simultaneously in a single step. In this process an inert and biocompatible organic solvent is introduced directly into the fermentation vessel to selectively extract the ethanol product. The ethanol is readily recovered from the solvent at high concentration by means of flash vaporization, and the solvent is recycled in a closed loop back to the fermentor. This process is characterized by a high productivity (since ethanol does not build up to inhibitory levels), continuous operation, significantly reduced water consumption, and lower product recovery costs. The technical advantages of this processing strategy have been extensively demonstrated by means of a continuous, fully integrated and computer-controlled Process Demonstration Unit in the authors' laboratory. Numerous features of this technology have been protected by US patent. A thorough economic comparison of Extractive Fermentation relative to modern ethanol technology (continuous with cell recycle) has been completed for both new plants and retrofitting of existing facilities for a capacity of 100 million liters of ethanol per year. Substantial cost savings are possible with Extractive Fermentation ranging, depending on the process configuration, from 5 cents to 16 cents per liter. Activities are under way to transfer this proprietary technology to the private sector

Anaerobic reductive dechlorination of tetrachloroethene: how can dual Carbon-Chlorine isotopic measurements help elucidating the underlying reaction mechanism?

Science.gov (United States)

Badin, Alice; Buttet, Géraldine; Maillard, Julien; Holliger, Christof; Hunkeler, Daniel

2014-05-01

Chlorinated ethenes (CEs) such as tetrachloroethene (PCE) are common persistent groundwater contaminants. Among clean-up strategies applied to sites affected by such pollution, bioremediation has been considered with a growing interest as it represents a cost-effective, environmental friendly approach. This technique however sometimes leads to an incomplete and slow biodegradation of CEs resulting in an accumulation of toxic metabolites. Understanding the reaction mechanisms underlying anaerobic reductive dechlorination would thus help assessing PCE biodegradation in polluted sites. Stable isotope analysis can provide insight into reaction mechanisms. For chlorinated hydrocarbons, carbon (C) and chlorine (Cl) isotope data (δ13C and δ37Cl) tend to show a linear correlation with a slope (m ≡ ɛC/ɛCl) characteristic of the reaction mechanism [1]. This study hence aims at exploring the potential of a dual C-Cl isotope approach in the determination of the reaction mechanisms involved in PCE reductive dechlorination. C and Cl isotope fractionation were investigated during anaerobic PCE dechlorination by two bacterial consortia containing members of the Sulfurospirillum genus. The specificity in these consortia resides in the fact that they each conduct PCE reductive dechlorination catalysed by one different reductive dehalogenase, i.e. PceADCE which yields trichloroethene (TCE) and cis-dichloroethene (cDCE), and PceATCE which yields TCE only. The bulk C isotope enrichment factors were -3.6±0.3 o for PceATCE and -0.7±0.1o for PceADCE. The bulk Cl isotope enrichment factors were -1.3±0.2 o for PceATCE and -0.9±0.1 o for PceADCE. When applying the dual isotope approach, two m values of 2.7±0.1 and 0.7±0.2 were obtained for the reductive dehalogenases PceATCE and PceADCE, respectively. These results suggest that PCE can be degraded according to two different mechanisms. Furthermore, despite their highly similar protein sequences, each reductive dehalogenase seems

MedlinePlus Connect: Technical Information

Science.gov (United States)

... MedlinePlus Connect → Technical Information URL of this page: https://medlineplus.gov/connect/technical.html MedlinePlus Connect: Technical ... will change.) Old URLs New URLs Web Application https://apps.nlm.nih.gov/medlineplus/services/mpconnect.cfm? ...

Technical Training: Technical Training Seminar

CERN Multimedia

2004-01-01

TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch Tuesday 3 February 2004 From 09:00 to 13:30 - Training Centre Auditorium - bldg. 593, room 11 USB (Universal Serial Bus) CYPRESS Seminar Claudia Colombini, Field Application Engineer CYPRESS ActiveComp Electronic GmbH D-85077 MANCHING, Germany As a pioneer in USB, CYPRESS sets the standard for cost-effective solutions without sacrificing functionality, performance or reliability. Having shipped over 200 million USB devices, Cypress is the undisputed market leader and demonstrates unmatched USB expertise. With the industry's broadest selection of USB solutions, Cypress has the right silicon, software and support for every USB application, from Low-speed to High-Speed and USB On-The-Go (OTG). 9:00 - 10:30 Overview of USB systems. USB CYPRESS product overview. Peripherals: Low Speed, Full Speed, High Speed (1.1 and 2.0). Hub Solutions, Embedded Host Solutions, On-The-Go (OTG) and wireless USB. USB Development Tools (first part) 10:30 -...

Technical Writing: Past, Present and Future

Science.gov (United States)

Mathes, J. C. (Compiler); Pinelli, T. E. (Compiler)

1981-01-01

The training of technical writers and the objectives of such education are discussed. Special emphasis was placed on the communication between technical personnel and non-technical personnel. The liabilities that affect technical writers were also discussed.

TECHNICAL CULTURE AND HUMAN AXJOSPHERE

Directory of Open Access Journals (Sweden)

­Krystyna Chałas

2014-11-01

Full Text Available Technical culture is the value of each historical period. It is the subject of the ongoing development. While it is a value which is associated with different categories of values, mainly material, cognitive, social. Between culture and these three categories of values ​ there is a cognitive effect. Technical culture determines the quality of human axjosphere. The aim of this study is to show the relationships and dependencies between technical culture and the structures in which a person lives and works. It is mainly about the answer to the question of which values of technical culture are closely related to and what are the inter dependencies? The primary task is to define the concept of the technical culture and to show its teaching essence. The second task boils down to indicate the range of values ​​inherent in the culture of technology, determining the value of the technological culture and values, which are developed by the technical culture. Indication of the interaction between the technical culture and values ​​is the third task.

Technical specification use and application

International Nuclear Information System (INIS)

Williamson, D.; Hoffman, D.R.

1991-01-01

Since early 1988 intensive efforts have been under way to produce a new and improved Standard Technical Specification. The program involves a coordinated effort between utility personnel representing each of the four nuclear steam supply system (NSSS) product lines, the NSSS vendors, and the US Nuclear Regulatory Commission (NRC). This intensive work period is actually the culmination of a decade of rhetoric about shortcomings of the existing technical specifications. Work on the improved technical specifications provided a unique forum for intense philosophical discussions between the users and enforcers of technical specifications, the outcome of which could have an impact on all licensees. Some of the more intriguing difficulties in the use and application of existing technical specifications, as well as discussions of the resolutions being applied in the improved technical specifications and the dilemmas remaining to be resolved are discussed in the paper

Efficient separations and processing crosscutting program 1996 technical exchange meeting. Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

This document contains summaries of technology development presented at the 1996 Efficient Separations and Processing Crosscutting Program Technical Exchange Meeting. This meeting is held annually to promote a free exchange of ideas among technology developers, potential users and other interested parties within the EM community. During this meeting the following many separation processes technologies were discussed such as ion exchange, membrane separation, vacuum distillation, selective sorption, and solvent extraction. Other topics discussed include: waste forms; testing or inorganic sorbents for radionuclide and heavy metal removal; selective crystallization; and electrochemical treatment of liquid wastes. This is the leading abstract, individual papers have been indexed separately for the databases.

Efficient separations and processing crosscutting program 1996 technical exchange meeting. Proceedings

International Nuclear Information System (INIS)

1996-01-01

This document contains summaries of technology development presented at the 1996 Efficient Separations and Processing Crosscutting Program Technical Exchange Meeting. This meeting is held annually to promote a free exchange of ideas among technology developers, potential users and other interested parties within the EM community. During this meeting the following many separation processes technologies were discussed such as ion exchange, membrane separation, vacuum distillation, selective sorption, and solvent extraction. Other topics discussed include: waste forms; testing or inorganic sorbents for radionuclide and heavy metal removal; selective crystallization; and electrochemical treatment of liquid wastes. This is the leading abstract, individual papers have been indexed separately for the databases

Technical resource documents and technical handbooks for hazardous-wastes management

Energy Technology Data Exchange (ETDEWEB)

Schomaker, N.B.; Bliss, T.M.

1986-07-01

The Environmental Protection Agency is preparing a series of Technical Resource Documents (TRD's) and Technical Handbooks to provide best engineering control technology to meet the needs of the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) respectively. These documents and handbooks are basically compilation of research efforts of the Land Pollution Control Division (LPCD) to date. The specific areas of research being conducted under the RCRA land disposal program relate to laboratory, pilot and field validation studies in cover systems, waste leaching and solidification, liner systems and disposal facility evaluation. The technical handbooks provide the EPA Program Offices and Regions, as well as the states and other interested parties, with the latest information relevant to remedial actions.

Technical standards in nuclear area

International Nuclear Information System (INIS)

Grimberg, M.

1978-01-01

The technical standardization in nuclear area is discussed. Also, the competence of CNEN in standardization pursuit is analysed. Moreover, the process of working up of technical standards is explained; in addition, some kinds of technical standards are discussed. (author) [pt

Technical Writing Tips

Science.gov (United States)

Kennedy, Patrick M.

2004-01-01

The main reason engineers, technicians, and programmers write poor technical documents is because they have had little training or experience in that area. This article addresses some of the basics that students can use to master technical writing tasks. The article covers the most common problems writers make and offers suggestions for improving…

Direct Biohydrometallurgical Extraction of Iron from Ore. Final Technical Report

International Nuclear Information System (INIS)

T.C. Eisele

2005-01-01

A completely novel approach to iron extraction was investigated, based on reductive leaching of iron by anaerobic bacteria. Microorganisms were collected from an anaerobic bog where natural seepage of dissolved iron was observed. This mixed culture was used to reduce insoluble iron in a magnetite ore to the soluble ferrous (Fe +2 ) state. While dissolution rates were slow, concentrations of dissolved iron as high as 3487 mg/l could be reached if sufficient time was allowed. A factorial study of the effects of trace nutrients and different forms of organic matter indicated that the best dissolution rates and highest dissolved iron concentrations were achieved using soluble carbohydrate (sucrose) as the bacterial food source, and that nutrients other than nitrogen, phosphorus, potassium, sodium, and acetate were not necessary. A key factor in reaching high levels of dissolved iron was maintaining a high level of carbon dioxide in solution, since the solubility of iron carbonates increases markedly as the quantity of dissolved carbon dioxide increases. Once the iron is dissolved, it has been demonstrated that the ferrous iron can then be electroplated from solution, provided that the concentration of iron is sufficiently high and the hydrogen ion concentration is sufficiently low. However, if the leaching solution is electrolyzed directly, organic matter precipitates at the cathode along with the metallic iron. To prevent this problem, the ferrous iron should be separated from the bulk solution in a more concentrated, purified form. One route to accomplishing this is to take advantage of the change in solubility of ferrous iron as a function of carbon dioxide concentration. By cycling the concentration of carbon dioxide in solution, it is possible to produce an iron-rich concentrate that should be suitable for electrolysis. This represents the first viable hydrometallurgical method for leaching iron directly from ore and producing metallic iron

Direct Biohydrometallurgical Extraction of Iron from Ore. Final technical report

International Nuclear Information System (INIS)

T.C. Eisele

2005-01-01

A completely novel approach to iron extraction was investigated, based on reductive leaching of iron by anaerobic bacteria. Microorganisms were collected from an anaerobic bog where natural seepage of dissolved iron was observed. This mixed culture was used to reduce insoluble iron in a magnetite ore to the soluble ferrous (Fe +2 ) state. While dissolution rates were slow, concentrations of dissolved iron as high as 3487 mg/l could be reached if sufficient time was allowed. A factorial study of the effects of trace nutrients and different forms of organic matter indicated that the best dissolution rates and highest dissolved iron concentrations were achieved using soluble carbohydrate (sucrose) as the bacterial food source, and that nutrients other than nitrogen, phosphorus, potassium, sodium, and acetate were not necessary. A key factor in reaching high levels of dissolved iron was maintaining a high level of carbon dioxide in solution, since the solubility of iron carbonates increases markedly as the quantity of dissolved carbon dioxide increases. Once the iron is dissolved, it has been demonstrated that the ferrous iron can then be electroplated from solution, provided that the concentration of iron is sufficiently high and the hydrogen ion concentration is sufficiently low. However, if the leaching solution is electrolyzed directly, organic matter precipitates at the cathode along with the metallic iron. To prevent this problem, the ferrous iron should be separated from the bulk solution in a more concentrated, purified form. One route to accomplishing this is to take advantage of the change in solubility of ferrous iron as a function of carbon dioxide concentration. By cycling the concentration of carbon dioxide in solution, it is possible to produce an iron-rich concentrate that should be suitable for electrolysis. This represents the first viable hydrometallurgical method for leaching iron directly from ore and producing metallic iron

TECHNICAL COORDINATION

CERN Multimedia

A. Ball

Overview From a technical perspective, CMS has been in “beam operation” state since 6th November. The detector is fully closed with all components operational and the magnetic field is normally at the nominal 3.8T. The UXC cavern is normally closed with the radiation veto set. Access to UXC is now only possible during downtimes of LHC. Such accesses must be carefully planned, documented and carried out in agreement with CMS Technical Coordination, Experimental Area Management, LHC programme coordination and the CCC. Material flow in and out of UXC is now strictly controlled. Access to USC remains possible at any time, although, for safety reasons, it is necessary to register with the shift crew in the control room before going down.It is obligatory for all material leaving UXC to pass through the underground buffer zone for RP scanning, database entry and appropriate labeling for traceability. Technical coordination (notably Stephane Bally and Christoph Schaefer), the shift crew and run ...

TECHNICAL COORDINATION

CERN Multimedia

A. Ball and W. Zeuner

2011-01-01

In this report we will review the main achievements of the Technical Stop and the progress of several centrally-managed projects to support CMS operation and maintenance and prepare the way for upgrades. Overview of the extended Technical Stop  The principal objectives of the extended Technical Stop affecting the detector itself were the installation of the TOTEM T1 telescopes on both ends, the readjustment of the alignment link-disk in YE-2, the replacement of the light-guide sleeves for all PMs of both HFs, and some repairs on TOTEM T2 and CASTOR. The most significant tasks were, however, concentrated on the supporting infrastructure. A detailed line-by-line leak search was performed in the C6F14 cooling system of the Tracker, followed by the installation of variable-frequency drives on the pump motors of the SS1 and SS2 tracker cooling plants to reduce pressure transients during start-up. In the electrical system, larger harmonic filters were installed in ...

Identification of anti-HBV activities in Paeonia suffruticosa Andr. using GRP78 as a drug target on Herbochip®.

Science.gov (United States)

Lam, Iao-Fai; Huang, Min; Chang, Margaret Dah-Tysr; Yao, Pei-Wun; Chou, Yu-Ting; Ng, Sim-Kun; Tsai, Ying-Lin; Lin, Yu-Chang; Zhang, Yun-Feng; Yang, Xiao-Yuan; Lai, Yiu-Kay

2017-01-01

Herbochip ® technology is a high throughput drug screening platform in a reverse screening manner, in which potential chemical leads in herbal extracts are immobilized and drug target proteins can be used as probes for screening process [BMC Complementary and Alternative Medicine (2015) 15:146]. While herbal medicines represent an ideal reservoir for drug screenings, here a molecular chaperone GRP78 is demonstrated to serve as a potential target for antiviral drug discovery. We cloned and expressed a truncated but fully functional form of human GRP78 (hGRP78 1-508 ) and used it as a probe for anti-HBV drug screening on herbochips. In vitro cytotoxicity and in vitro anti-HBV activity of the herbal extracts were evaluated by MTT and ELISA assays, respectively. Finally, anti-HBV activity was confirmed by in vivo assay using DHBV DNA levels in DHBV-infected ducklings as a model. Primary screenings using GRP78 on 40 herbochips revealed 11 positives. Four of the positives, namely Dioscorea bulbifera , Lasiosphaera fenzlii , Paeonia suffruticosa and Polygonum cuspidatum were subjected to subsequent assays. None of the above extracts was cytotoxic to AML12 cells, but P. cuspidatum extract (PCE) was found to be cytotoxic to HepG2 2.2.15 cells. Both PCE and P. suffruticosa extract (PSE) suppressed secretion of HBsAg and HBeAg in HepG2 2.2.15 cells. The anti-HBV activity of PSE was further confirmed in vivo. We have demonstrated that GRP78 is a valid probe for anti-HBV drug screening on herbochips. We have also shown that PSE, while being non-cytotoxic, possesses in vitro and in vivo anti-HBV activities. Taken together, our data suggest that PSE may be a potential anti-HBV agent for therapeutic use.

LHC Availability 2017: Technical Stop 1 to Technical Stop 2

CERN Document Server

Todd, Benjamin; Apollonio, Andrea; Walsh, David John; CERN. Geneva. ATS Department

2017-01-01

This document summarises the LHC machine availability for the period of Technical Stop 1 (TS1) to Technical Stop 2 (TS2) in 2017. This period was dedicated to proton physics with a bunch spacing of 25ns. This note has been produced and ratified by the Availability Working Group which has complied fault information for the period in question using the Accelerator Fault Tracker.

Delay-based Passenger Car Equivalent at Signalized Intersections in Iran

Directory of Open Access Journals (Sweden)

Habibollah Nassiri

2017-04-01

Full Text Available Due to their different sizes and operational characteristics, vehicles other than passenger cars have a different influence on traffic operations especially at intersections. The passenger car equivalent (PCE is the parameter that shows how many passenger cars must be substituted for a specific heavy vehicle to represent its influence on traffic operation. PCE is commonly estimated using headway-based methods that consider the excess headway utilized by heavy vehicles. In this research, the PCE was estimated based on the delay parameter at three signalized intersections in Tehran, Iran. The data collected were traffic volume, travel time for each movement, signalization, and geometric design information. These data were analysed and three different models, one for each intersection, were constructed and calibrated using TRAF-NETSIM simulation software for unsaturated traffic conditions. PCE was estimated under different scenarios and the number of approach movements at each intersection. The results showed that for approaches with only one movement, PCE varies from 1.1 to 1.65. Similarly, for approaches with two and three movements, the PCE varies from 1.07 to 1.99 and from 0.76 to 3.6, respectively. In addition, a general model was developed for predicting PCE for intersections with all of the movements considered. The results obtained from this model showed that the average PCE of 1.5 is similar to the value recommended by the HCM (Highway Capacity Manual 1985. However, the predicted PCE value of 1.9 for saturated threshold is closer to the PCE value of 2 which was recommended by the HCM 2000 and HCM 2010.

Idaho Chemical Processing Plant and Plutonium-Uranium Extraction Plant phaseout/deactivation study

International Nuclear Information System (INIS)

Patterson, M.W.; Thompson, R.J.

1994-01-01

The decision to cease all US Department of Energy (DOE) reprocessing of nuclear fuels was made on April 28, 1992. This study provides insight into and a comparison of the management, technical, compliance, and safety strategies for deactivating the Idaho Chemical Processing Plant (ICPP) at Westinghouse Idaho Nuclear Company (WINCO) and the Westinghouse Hanford Company (WHC) Plutonium-Uranium Extraction (PUREX) Plant. The purpose of this study is to ensure that lessons-learned and future plans are coordinated between the two facilities

Technical evaluation report of the Fort St. Vrain final draft upgraded technical specifications

International Nuclear Information System (INIS)

Kimura, C.Y.

1989-01-01

This report is a technical evaluation of the final draft of the Fort St. Vrain (FSV) Upgraded Technical Specifications (UT/S) as issued by Public Service of Colorado (PSC) on May 27, 1988 with subsequent supplemental updates issued on June 15, 1988 and August 5, 1988. It has been compared for consistency, and safety conservatism with the Fort St. Vrain (FSV) Updated Final Safety Analysis Report (FSAR), the FSV Safety Evaluation Report (SER), the Facility Operating License, DPR-34, and all amendments to the Facility Operating License issued as of June 1, 1988, and Appendix A to the Operating License DPR-34, Technical Specifications. Because of the age of the plant, no supplements to the Fort St. Vrain SER have been issued since the original SER was not issued as a WASH or a NUREG report. This made it necessary to review all amendments to the Facility Operating License since they would contain the safety evaluations done to support changes to the Facility Operating License. The upgraded Fort St. Vrain Technical Specifications were also broadly compared with the latest Westinghouse Standard Technical Specifications (WSTS) to assure that what was proposed for Fort St. Vrain was consistent with the latest NRC staff practices for standard technical specifications

Biotransformation of tetrachloroethylene to trichloroethylene, dichloroethylene, vinyl chloride, and carbon dioxide under methanogenic conditions

International Nuclear Information System (INIS)

Vogel, T.M.; McCarty, P.L.

1985-01-01

Tetrachloroethylene (PCE) and trichloroethylene (TCE), common industrial solvents, are among the most frequent contaminants found in groundwater supplies. Due to the potential toxicity and carcinogenicity of chlorinated ethylenes, knowledge about their transformation potential is important in evaluating their environmental fate. The results of this study confirm that PCE can be transformed by reductive dehalogenation to TCE, dichloroethylene, and vinyl chloride (VC) under anaerobic conditions. In addition, [ 14 C]PCE was at least partially mineralized to CO 2 . Mineralization of 24% of the PCE occurred in a continuous-flow fixed-film methanogenic column with a liquid detention time of 4 days. TCE was the major intermediate formed, but traces of dichloroethylene isomers and VC were also found. In other column studies under a different set of methanogenic conditions, nearly quantitative conversion of PCE to VC was found. These studies clearly demonstrate that TCE and VC are major intermediates in PCE biotransformation under anaerobic conditions and suggest that the potential exists for the complete mineralization of PCE to CO 2 in soil and aquifer systems and in biological treatment processes

A mass balance study of the phytoremediation of perchloroethylene-contaminated groundwater

International Nuclear Information System (INIS)

Andrew James, C.; Xin Gang; Doty, Sharon L.; Muiznieks, Indulis; Newman, Lee; Strand, Stuart E.

2009-01-01

A mass balance study was performed under controlled field conditions to investigate the phytoremediation of perchloroethylene (PCE) by hybrid poplar trees. Water containing 7-14 mg L -1 PCE was added to the test bed. Perchloroethylene, trichloroethylene, and cis-dichloroethylene were detected in the effluent at an average of 0.12 mg L -1 , 3.9 mg L -1 , and 1.9 mg L -1 , respectively. The total mass of chlorinated ethenes in the water was reduced by 99%. Over 95% of the recovered chlorine was as free chloride in the soil, indicating near-complete dehalogenation of the PCE. Transpiration, volatilization, and accumulation in the trees were all found to be minor loss mechanisms. In contrast, 98% of PCE applied to an unplanted soil chamber was recovered as PCE in the effluent water or volatilized into the air. These results suggest that phytoremediation can be an effective method for treating PCE-contaminated groundwater in field applications. - A chlorine balance performed on a planted test bed with PCE-contaminated water demonstrated VOC mass reduction of 99% and complete dechlorination.

A mass balance study of the phytoremediation of perchloroethylene-contaminated groundwater

Energy Technology Data Exchange (ETDEWEB)

Andrew James, C. [University of Washington, Department of Civil and Environmental Engineering, Seattle, WA (United States); Xin Gang [Hydranautics, 401 Jones Rd., Oceanside, CA 92058 (United States); Doty, Sharon L.; Muiznieks, Indulis [University of Washington, College of Forest Resources, Seattle, WA (United States); Newman, Lee [Brookhaven National Laboratory, Biology Department, Upton, NY (United States); Strand, Stuart E., E-mail: sstrand@u.washington.ed [University of Washington, Department of Civil and Environmental Engineering, Seattle, WA (United States)

2009-08-15

A mass balance study was performed under controlled field conditions to investigate the phytoremediation of perchloroethylene (PCE) by hybrid poplar trees. Water containing 7-14 mg L{sup -1} PCE was added to the test bed. Perchloroethylene, trichloroethylene, and cis-dichloroethylene were detected in the effluent at an average of 0.12 mg L{sup -1}, 3.9 mg L{sup -1}, and 1.9 mg L{sup -1}, respectively. The total mass of chlorinated ethenes in the water was reduced by 99%. Over 95% of the recovered chlorine was as free chloride in the soil, indicating near-complete dehalogenation of the PCE. Transpiration, volatilization, and accumulation in the trees were all found to be minor loss mechanisms. In contrast, 98% of PCE applied to an unplanted soil chamber was recovered as PCE in the effluent water or volatilized into the air. These results suggest that phytoremediation can be an effective method for treating PCE-contaminated groundwater in field applications. - A chlorine balance performed on a planted test bed with PCE-contaminated water demonstrated VOC mass reduction of 99% and complete dechlorination.

The technical supervision interface

CERN Document Server

Sollander, P

1998-01-01

The Technical Control Room (TCR) is currently using 30 different applications for the remote supervision of the technical infrastructure at CERN. These applications have all been developed with the CERN made Uniform Man Machine Interface (UMMI) tools built in 1990. However, the visualization technology has evolved phenomenally since 1990, the Technical Data Server (TDS) has radically changed our control system architecture, and the standardization and the maintenance of the UMMI applications have become important issues as their number increases. The Technical Supervision Interface is intended to replace the UMMI and solve the above problems. Using a standard WWW-browser for the display, it will be inherently multi-platform and hence available for control room operators, equipment specialists and on-call personnel.

Engineering Technical Review Planning Briefing

Science.gov (United States)

Gardner, Terrie

2012-01-01

The general topics covered in the engineering technical planning briefing are 1) overviews of NASA, Marshall Space Flight Center (MSFC), and Engineering, 2) the NASA Systems Engineering(SE) Engine and its implementation , 3) the NASA Project Life Cycle, 4) MSFC Technical Management Branch Services in relation to the SE Engine and the Project Life Cycle , 5) Technical Reviews, 6) NASA Human Factor Design Guidance , and 7) the MSFC Human Factors Team. The engineering technical review portion of the presentation is the primary focus of the overall presentation and will address the definition of a design review, execution guidance, the essential stages of a technical review, and the overall review planning life cycle. Examples of a technical review plan content, review approaches, review schedules, and the review process will be provided and discussed. The human factors portion of the presentation will focus on the NASA guidance for human factors. Human factors definition, categories, design guidance, and human factor specialist roles will be addressed. In addition, the NASA Systems Engineering Engine description, definition, and application will be reviewed as background leading into the NASA Project Life Cycle Overview and technical review planning discussion.

Technical training: places available

CERN Multimedia

2014-01-01

If you would like more information on a course, or have any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tel: 74924)

Technical training: places available

CERN Document Server

2013-01-01

If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tel: 74924)

Technical training - places available

CERN Document Server

2013-01-01

If you would like more information on a course, or have any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tel: 74924)

Peculiarities of extraction of carbonate complexes of trivalent transplutonium elements by alkylpyrocatechins

International Nuclear Information System (INIS)

Karalova, Z.K.; Bukina, T.I.; Myasoedov, B.F.; Fedorov, L.A.; Sokolovskij, S.A.

1987-01-01

Extraction of trivalent americium, curium, californium and europium by technical mixture of mono- and didecylpyrocatechin (TAP) in various diluents from carbonate solutions is investigated. Effect of many factors (pH, K 2 CO 3 concentration, TAP, metal; the time of phase contact) on the completeness of element isolation and separation is clarified. It is ascertained that the elements listed are quantitatively extracted by TAP solution in toluene and cyclohexane in the range of K 2 CO 3 concentrations from 0.25 to 1.5 mol/l. The difference in americium and curium distribution coefficient during their extraction by TAP from 0.25 mol/l of K 2 CO 3 solution is detected. Separation coefficients of the pair increase with the increase of carbonate solution pH. The separation can be improved at the stage of element reextraction by the mixture of K 2 CO 3 and DTPA or EDTA from alkylpyrocatechin, sunce rate constants of americium and curium reextraction differ greatly. Using 13 C NMR the composition of compounds in organic phase on the basis of 4-(α, α-dioctylethyl)pyrocatechin is investigated

Solvent extraction of uranium: Towards good practice in design, operation and management

International Nuclear Information System (INIS)

Bartsch, P.; Hall, S.; Ballestrin, S.; Hunt, A.

2014-01-01

Uranium solvent extraction, USX has been applied commercially for recovery and concentration for over 60 years. Uranium in acidic liquor, which is prepared following ore leaching, solid/liquid separation and clarification, can be treated through a sequence of operations; extraction-scrubbing-stripping, to obtain purified liquor, and hence precipitation of marketable products. USX has dominated the primary uranium industry as the preferred technological route for recovery of uranium into converter grade yellowcake or Uranium Ore Concentrate. The practices of design and operation of USX facilities has found renewed interest as new mines are developed following decades of industry dormancy. Development of the Olympic Dam and Honeymoon operations in Australia has lead to innovative design and operation of pulsed columns technology in applications of solvent extraction. This article seeks to outline principles of design and operation from the practitioner’s perspective. The discussion also reviews historical developments of USX applications and highlights recent innovations. This review is hoped to provide guidance for technical personnel who wish to learn more about good practices that leads to reliable USX performance. (author)

49 CFR 552.6 - Technical review.

Science.gov (United States)

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Technical review. 552.6 Section 552.6... § 552.6 Technical review. The appropriate Associate Administrator conducts a technical review of the petition. The technical review may consist of an analysis of the material submitted, together with...

Anaerobic bacteria that dechlorinate perchloroethene.

Science.gov (United States)

Fathepure, B Z; Nengu, J P; Boyd, S A

1987-01-01

In this study, we identified specific cultures of anaerobic bacteria that dechlorinate perchlorethene (PCE). The bacteria that significantly dechlorinated PCE were strain DCB-1, an obligate anaerobe previously shown to dechlorinate chlorobenzoate, and two strains of Methanosarcina. The rate of PCE dechlorination by DCB-1 compared favorably with reported rates of trichloroethene bio-oxidation by methanotrophs. Even higher PCE dechlorination rates were achieved when DCB-1 was grown in a methanogenic consortium. PMID:3426224

Technical training: places available

CERN Multimedia

2014-01-01

If you would like more information on a course, or have any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Marie Lahchimi, Technical Training Administration (Tel: 74924)

Technical training: places available

CERN Multimedia

2013-01-01

If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch. Eva Stern and Elise Romero, Technical Training Administration (Tél : 74924)  

The extraction of vanadium pentoxide from waste of titanium tetrachloride by various methods

Directory of Open Access Journals (Sweden)

Инна Михайловна Гунько

2015-04-01

Full Text Available In article the recovery possibility of vanadium pentoxide from wastes, formed as a result of purification from impurities of technical titanium tetrachloride is researched. The purification from impurities is realized by different methods – pulp of lower titanium chlorides, hydrocarbonic reducer and cascade-rectifying purification. Usage of these purification methods leads to formation of anthropogenic wastes. The researches is shown that processing of these wastes is reasonable for the purpose of vanadium pentoxide extraction

Technical Assistance Plan (TAP)

Science.gov (United States)

A Technical Assistance Plan (TAP) enables community groups to retain the services of an independent technical advisor and to provide resources for a community group to help inform other community members about site decisions.

Reader-Centered Technical Writing

Science.gov (United States)

Narayanan, M.

2012-12-01

Technical writing is an essential part of professional communication and in recent years it has shifted from a genre-based approach. Formerly, technical writing primarily focused on generating templates of documents and sometimes it was creating or reproducing traditional forms with minor modifications and updates. Now, technical writing looks at the situations surrounding the need to write. This involves deep thinking about the goals and objectives of the project on hand. Furthermore, one observes that it is very important for any participatory process to have the full support of management. This support needs to be well understood and believed by employees. Professional writing may be very persuasive in some cases. When presented in the appropriate context, technical writing can persuade a company to improve work conditions ensuring employee safety and timely production. However, one must recognize that lot of professional writing still continues to make use of reports and instruction manuals. Normally, technical and professional writing addresses four aspects. Objective: The need for generating a given professionally written technical document and the goals the document is expected to achieve and accomplish. Clientele: The clientele who will utilize the technical document. This may include the people in the organization. This may also include "unintended readers." Customers: The population that may be affected by the content of the technical document generated. This includes the stakeholders who will be influenced. Environment: The background in which the document is created. Also, the nature of the situation that warranted the generation of the document. Swiss Psychologist Jean Piaget's view of Learning focuses on three aspects. The author likes to extend Jean Piaget's ideas to students, who are asked to prepare and submit Reader-Centered Technical Writing reports and exercises. Assimilation: Writers may benefit specifically, by assimilating a new object into

Assessing Students' Technical Skill Attainment

Science.gov (United States)

Jorgensen, Haley

2010-01-01

The Wisconsin Technical College System (WTCS) is working to comply with the Carl D. Perkins Career and Technical Education Improvement Act of 2006 (Perkins) to ensure that its graduates have mastered the technical skills needed by business and industry. The legislation requires that each state identify and approve program assessment strategies…

Integrating technical and non-technical skills coaching in an acute trauma surgery team training: Is it too much?

Science.gov (United States)

Alken, Alexander; Luursema, Jan-Maarten; Weenk, Mariska; Yauw, Simon; Fluit, Cornelia; van Goor, Harry

2017-08-25

Research on effective integration of technical and non-technical skills in surgery team training is sparse. In a previous study we found that surgical teachers predominantly coached on technical and hardly on non-technical skills during the Definitive Surgical and Anesthetic Trauma Care (DSATC) integrated acute trauma surgery team training. This study aims to investigate whether the priming of teachers could increase the amount of non-technical skills coaching during such a training. Coaching activities of 12 surgical teachers were recorded on audio and video. Six teachers were primed on non-technical skills coaching prior to the training. Six others received no priming and served as controls. Blind observers reviewed the recordings of 2 training scenario's and scored whether the observed behaviors were directed on technical or non-technical skills. We compared the frequency of the non-technical skills coaching between the primed and the non-primed teachers and analyzed for differences according to the trainees' level of experience. Surgical teachers coached trainees during the highly realistic DSATC integrated acute trauma surgery team training. Trainees performed damage control surgery in operating teams on anesthetized porcine models during 6 training scenario's. Twelve experienced surgical teachers participated in this study. Coaching on non-technical skills was limited to about 5%. The primed teachers did not coach more often on non-technical skills than the non-primed teachers. We found no differences in the frequency of non-technical skills coaching based on the trainees' level of experience. Priming experienced surgical teachers does not increase the coaching on non-technical skills. The current DSATC acute trauma surgery team training seems too complex for integrating training on technical and non-technical skills. Patient care, Practice based learning and improvement. Copyright © 2017 Elsevier Inc. All rights reserved.

Direct 125I-radioligand assays for serum progesterone compared with assays involving extraction of serum

International Nuclear Information System (INIS)

Ratcliffe, W.A.; Corrie, J.E.T.; Dalziel, A.H.; Macpherson, J.S.

1982-01-01

Two direct radioimmunoassays for progesterone in 50 μL of unextracted serum or plasma with assays involving extraction of serum were compared. The direct assays include the use of either danazol at pH 7.4 or 8-anilino-1-naphthalenesulfonic acid at pH 4.0 to displace progesterone from serum binding-proteins. Progesterone is then assayed by using an antiserum to a progesterone 11α-hemisuccinyl conjugate and the radioligand 125 I-labeled progesterone 11α-glucuronyl tyramine, with separation by double-antibody techniques. Direct assays with either displacing agent gave good analytical recovery of progesterone added to human serum, and progesterone values for patients' specimens correlated well (r > 0.96) with results of assays involving extraction of serum. Precision was similar with each displacing agent over the working range 2.5-100 nmol/L and superior to that of extraction assays. We conclude that these direct assays of progesterone are analytically valid and more robust, precise, and technically convenient than many conventional methods involving extraction of serum

Simulation-based ureteroscopy skills training curriculum with integration of technical and non-technical skills: a randomised controlled trial.

Science.gov (United States)

Brunckhorst, Oliver; Shahid, Shahab; Aydin, Abdullatif; McIlhenny, Craig; Khan, Shahid; Raza, Syed Johar; Sahai, Arun; Brewin, James; Bello, Fernando; Kneebone, Roger; Khan, Muhammad Shamim; Dasgupta, Prokar; Ahmed, Kamran

2015-09-01

Current training modalities within ureteroscopy have been extensively validated and must now be integrated within a comprehensive curriculum. Additionally, non-technical skills often cause surgical error and little research has been conducted to combine this with technical skills teaching. This study therefore aimed to develop and validate a curriculum for semi-rigid ureteroscopy, integrating both technical and non-technical skills teaching within the programme. Delphi methodology was utilised for curriculum development and content validation, with a randomised trial then conducted (n = 32) for curriculum evaluation. The developed curriculum consisted of four modules; initially developing basic technical skills and subsequently integrating non-technical skills teaching. Sixteen participants underwent the simulation-based curriculum and were subsequently assessed, together with the control cohort (n = 16) within a full immersion environment. Both technical (Time to completion, OSATS and a task specific checklist) and non-technical (NOTSS) outcome measures were recorded with parametric and non-parametric analyses used depending on the distribution of our data as evaluated by a Shapiro-Wilk test. Improvements within the intervention cohort demonstrated educational value across all technical and non-technical parameters recorded, including time to completion (p technical and non-technical skills teaching is both educationally valuable and feasible. Additionally, the curriculum offers a validated simulation-based training modality within ureteroscopy and a framework for the development of other simulation-based programmes.

Self vs expert assessment of technical and non-technical skills in high fidelity simulation.

Science.gov (United States)

Arora, Sonal; Miskovic, Danilo; Hull, Louise; Moorthy, Krishna; Aggarwal, Rajesh; Johannsson, Helgi; Gautama, Sanjay; Kneebone, Roger; Sevdalis, Nick

2011-10-01

Accurate assessment is imperative for learning, feedback and progression. The aim of this study was to examine whether surgeons can accurately self-assess their technical and nontechnical skills compared with expert faculty members' assessments. Twenty-five surgeons performed a laparoscopic cholecystectomy (LC) in a simulated operating room. Technical and nontechnical performance was assessed by participants and faculty members using the validated Objective Structured Assessment of Technical Skills (OSATS) and the Non-Technical Skills for Surgeons scale (NOTSS). Assessment of technical performance correlated between self and faculty members' ratings for experienced (median score, 30.0 vs 31.0; ρ = .831; P = .001) and inexperienced (median score, 22.0 vs 28.0; ρ = .761; P = .003) surgeons. Assessment of nontechnical skills between self and faculty members did not correlate for experienced surgeons (median score, 8.0 vs 10.5; ρ = -.375; P = .229) or their more inexperienced counterparts (median score, 9.0 vs 7.0; ρ = -.018; P = .953). Surgeons can accurately self-assess their technical skills in virtual reality LC. Conversely, formal assessment with faculty members' input is required for nontechnical skills, for which surgeons lack insight into their behaviours. Copyright © 2011 Elsevier Inc. All rights reserved.

Technical Support and Transfer of Geothrmal Technical Knowledge and Information

Energy Technology Data Exchange (ETDEWEB)

John W. Lund; Toni" Boyd

2007-11-14

The Geo-Heat Center (GHC) staff provided responses to 1442 technical support requests during the contract period (April 1, 2006 to September 30, 2007), which were six quarters under this contract. Our website, consisting of 1900 files, also contributes to our technical assistance activity. Downloaded files were 1,889,323 (3,448 per day) from our website, the total number of users was 1,365,258 (2,491 per day), and the total number of hits were 6,008,500 (10,064 per day). The GHC staff attended 60 workshops, short course and professional meeting and made 29 technical presentations. The staff also prepared and mailed out 2,000 copies of each of five issues of the GHC Quaterly Bulletin which contained 26 articles. We also mailed out approximately 5,000 papers and publications to interested individuals and organizations.

Assessing the capacity of zero valent iron nanofluids to remediate NAPL-polluted porous media

Energy Technology Data Exchange (ETDEWEB)

Tsakiroglou, Christos, E-mail: ctsakir@iceht.forth.gr [Foundation for Research and Technology Hellas-Institute of Chemical Engineering Sciences, Stadiou street, Platani, 26504 Patras (Greece); Terzi, Katerina; Sikinioti-Lock, Alexandra [Foundation for Research and Technology Hellas-Institute of Chemical Engineering Sciences, Stadiou street, Platani, 26504 Patras (Greece); Department of Chemical Engineering, University of Patras, 26504 Patras (Greece); Hajdu, Kata; Aggelopoulos, Christos [Foundation for Research and Technology Hellas-Institute of Chemical Engineering Sciences, Stadiou street, Platani, 26504 Patras (Greece)

2016-09-01

A variety of aqueous suspensions (nanofluids) of zero-valent nano-particles (nZVI) are prepared by wet chemistry techniques, their stability and longevity is evaluated by physic-chemical methods of characterization, and their reactivity toward the dechlorination of per-chloro-ethylene (PCE) is examined with tests in batch reactors. For assessing the mobility, longevity and reactivity of nZVI suspensions (nanofluids), under flow-through conditions, visualization multiphase flow and transport tests are performed on a glass-etched pore network. The nZVI breakthrough curves are constructed by measuring the transient variation of the iron concentration in the effluent with atomic absorption spectroscopy. The capacity of nZVI to remediate the bulk phase of PCE is quantified by detecting the mass loss rate of PCE ganglia trapped in glass-etched pore networks during the continuous injection of nZVI suspension or pure water. The nZVI injection in porous media is simulated as an advection- dispersion process by accounting for the attachment/detachment of nanoparticles on the pore-walls, and describing the kinetics of PCE dissolution and reaction by 1st order equations. Visualization experiments reveal that the gradual elimination of PCE ganglia by the injected nZVI is associated with the preferential “erosion” of the upstream interfacial regions. The step controlling the overall process kinetics might be either (i) the enhanced PCE dissolution or (ii) the direct reaction of bulk PCE with the nZVI deposited upon the ganglia interfaces. Inverse modeling of the experiments under the simplifying assumption of one active mechanism indicates that the estimated kinetic coefficients are increasing functions of the flow rate. - Highlights: • The PCE remediation by nZVI is studied with visualization tests on pore networks. • The remediation of PCE ganglia by nZVI follows a non-uniform “erosion” pattern. • The preferential erosion of the upstream interfacial regions of

Critical review of the epidemiological literature on occupational exposure to perchloroethylene and cancer.

Science.gov (United States)

Mundt, Kenneth A; Birk, Thomas; Burch, Margaret T

2003-09-01

Of an estimated 500,000 workers in the USA potentially exposed to perchloroethylene (PCE), the largest share is employed in the dry-cleaning industry. PCE, a non-flammable solvent, has commercial applications as a chemical intermediate, metal degreaser and, since the 1950s, primary solvent in the dry-cleaning industry. The International Agency for Research on Cancer (IARC) currently finds sufficient evidence to designate PCE as carcinogenic in animals, with limited evidence in humans. With regard to occupational exposure through dry-cleaning, PCE is considered to be possibly carcinogenic to humans. This review was conducted to assess the current epidemiological literature on PCE and specific cancers. A comprehensive search was conducted to identify all available epidemiological literature pertaining to the carcinogenic effects of PCE. Forty-four papers that provided reasonable data on up to 17 cancer sites were critically reviewed in the context of the available background literature for each cancer site and were assessed on the basis of specified methodological and scientific quality criteria. While all the epidemiological studies selected for review investigated similar exposure-health outcome relationships, there was a broad diversity of proxy measurements of exposure to PCE, as well as numerous specific cancer outcomes of interest. The widespread lack of valid exposure measurements or other adequate indicators of potential for exposure were consistent limitations. We found no evidence of an association between breast, prostate, skin or brain cancer and exposure to PCE. A relationship between PCE and cancer of the following sites was considered unlikely: oral cavity, liver, pancreas, cervix lung. Scientific evidence was inadequate for laryngeal, kidney, esophageal and bladder cancers. The current epidemiological evidence does not support a conclusion that occupational exposure to PCE is a risk factor for cancer of any specific site. Priority areas in which

Occurrence of perchloroethylene in surface water and fish in a river ecosystem affected by groundwater contamination.

Science.gov (United States)

Wittlingerová, Zdena; Macháčková, Jiřina; Petruželková, Anna; Zimová, Magdalena

2016-03-01

Long-term monitoring of the content of perchloroethylene (PCE) in a river ecosystem affected by groundwater contamination was performed at a site in the Czech Republic. The quality of surface water was monitored quarterly between 1994 and 2013, and fish were collected from the affected ecosystem to analyse the content of PCE in their tissue in 1998, 2011 and 2012. Concentrations of PCE (9-140 μg/kg) in the tissue of fish collected from the contaminated part of the river were elevated compared to the part of the river unaffected by the contamination (ND to 5 μg/kg PCE). The quality of surface water has improved as a result of groundwater remediation during the evaluated period. Before the remedial action, PCE concentrations ranged from 30 to 95 μg/L (1994-1997). Following commencement of remedial activities in September 1997, a decrease in the content of PCE in the surface water to 7.3 μg/L (1998) and further to 1 μg/L (2011) and 1.1 μg/L (2012) led to a progressive decrease in the average concentration of PCE in the fish muscle tissue from 79 μg/kg (1998) to 24 (2011) and 30 μg/kg (2012), respectively. It was determined that the bioconcentration of PCE does not have a linear dependence because the decrease in contamination in the fish muscle tissue is not directly proportional to the decrease in contamination in the river water. The observed average bioconcentration factors were 24 and 28 for the lower concentrations of PCE and 11 for the higher concentrations of PCE in the river. In terms of age, length and weight of the collected fish, weight had the greatest significance for bioconcentration, followed by the length, with age being evaluated as a less significant factor.

Citation analysis of Computer Standards & Interfaces: Technical or also non-technical focus?

NARCIS (Netherlands)

G. van de Kaa (Geerten); H.J. de Vries (Henk); B. Baskaran (Balakumaran)

2015-01-01

textabstractThis paper analyzes to which extent research published in Computer Standards & Interfaces (CSI) has a technical focus. We find that CSI has been following its scope very closely in the last three years and that the majority of its publications have a technical focus. Articles published

Control of heavy loads at nuclear power plants: Resolution of Generic Technical Activity A-36. Technical report

International Nuclear Information System (INIS)

George, H.J.

1980-07-01

This report summarizes work performed by the NRC staff in the resolution of Generic Technical Activity A-36, Control of Heavy Loads Near Spent Fuel. Generic Technical Activity A-36 is one of the generic technical subjects designated as unresolved safety issues pursuant to Section 210 of the Energy Reorganization Act of 1974. The report describes the technical studies and evaluations performed by the NRC staff, the staff's guidelines based on these studies, and the staff's plans for implementaton of its technical guidelines

Technical report writing today

CERN Document Server

Riordan, Daniel G

2014-01-01

"Technical Report Writing Today" provides thorough coverage of technical writing basics, techniques, and applications. Through a practical focus with varied examples and exercises, students internalize the skills necessary to produce clear and effective documents and reports. Project worksheets help students organize their thoughts and prepare for assignments, and focus boxes highlight key information and recent developments in technical communication. Extensive individual and collaborative exercises expose students to different kinds of technical writing problems and solutions. Annotated student examples - more than 100 in all - illustrate different writing styles and approaches to problems. Numerous short and long examples throughout the text demonstrate solutions for handling writing assignments in current career situations. The four-color artwork in the chapter on creating visuals keeps pace with contemporary workplace capabilities. The Tenth Edition offers the latest information on using electronic resum...

Factors Affecting Women Enrolment In Technical Institutions In Tanzania A Case Study Of Arusha Technical College

OpenAIRE

Glory B. Kaaya; Dr. Esther Waiganjo

2015-01-01

Abstract The purpose of this study was to investigate the factors affecting women enrolment in Technical Institutions in Tanzania by focusing on the women. The study examined in detail the factors affecting women enrolment in Technical institutions and Arusha Technical College in particular as well as exploring sexual dynamics within Technical Institutions. Moreover a number of theoretical frameworks were concerned basing on the objectives a case study design was employed involving both qua...

Technical Report Writing Today

DEFF Research Database (Denmark)

Riordan, Daniel G.

2014-01-01

Section 1: Technical Communication Basics (8 chapters on tech com, audiences, tech com process, tech com style, researching, designing pages, using visual aids, describing). Section 2: Technical Communication Applications (7 chapters on sets of instructions, informal reports and email, developing...

Technical Training: WBTechT offers online training

CERN Multimedia

Monique Duval

2005-01-01

CERN Technical Training 2005 The 2005 CERN Web-Based Technical Training portal is a computer-skills site offering multimedia learning. Visit http://www.course-source.net/sites/cern/ to self-register, consult the available programmes or request a course via EDH. A self-directed online course costs 50.- CHF for desktop applications and 90.- CHF for technical applications for three months' unlimited access. Visit the WBTechT portal or http://www.cern.ch/TechnicalTraining, and contact Technical.Training@cern.ch or your DTOs to find out more information. ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING Monique Duval 74924 technical.training@cern.ch

Technical Training: WBTechT offers online training

CERN Multimedia

Monique Duval

2005-01-01

CERN Technical Training 2005 The 2005 CERN Web-Based Technical Training (WBTechT) portal is a computer-skills site offering multimedia learning. Visit http://www.course-source.net/sites/cern/ to self-register, consult the available programmes or request a course via EDH. A self-directed online course costs 50.- CHF for desktop applications and 90.- CHF for technical applications for three months' unlimited access. Visit the WBTechT portal or http://www.cern.ch/TechnicalTraining, and contact Technical.Training@cern.ch or your DTO to find out more information. ENSEIGNEMENT TECHNIQUE TECHNICAL TRAINING Monique Duval 74924 technical.training@cern.ch

Net-Zero Energy Technical Shelter

DEFF Research Database (Denmark)

Zhang, Chen; Heiselberg, Per; Jensen, Rasmus Lund

2014-01-01

Technical shelters are the basic structures for storing electronic and technical equipment, and commonly used for telecommunication base station, windmill, gas station, etc. Due to their high internal heat load density and special operation schedule, they consume more energy than normal residential...... or commercial buildings. On the other hand, it is a big challenge to power the technical shelter in remote area where the grids are either not available or the expansion of grid is expensive. In order to minimize the energy consumption and obtain a reliable and cost-efficient power solution for technical...... shelter, this study will apply the net-zero energy concept into the technical shelter design. The energy conservation can be achieved by proper design of building envelop and optimization of the cooling strategies. Both experiments and numerical simulations are carried out to investigate the indoor...

Technical planning activity: Final report

Energy Technology Data Exchange (ETDEWEB)

1987-01-01

In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements.

Technical planning activity: Final report

International Nuclear Information System (INIS)

1987-01-01

In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements

Study on the extraction kinetics of U(IV) extraction with neutral phosphoric extractant

International Nuclear Information System (INIS)

Lin Zhou; Liao Shishu; Li Zhou

1995-04-01

The extraction kinetics of U(IV) in the diisooctyl isobutylphosphonate system has been studied by using the single drop method. The effects of the concentrations of U(IV), HCl and extractant on the extraction rate have been examined. In a certain HCl concentration, the extraction rate equation has been acquired and in the condition of various HCl concentration the extraction rate of U(IV) is proportional to [HCl 1.51 . The effect of operation temperature was also examined, and the calculated apparent activation energy is equal to 23.24 kJ/mol. From the experimental results, the extraction reaction process and the rate-controlling step have been deduced. (4 figs., 5 tabs.)

OSH technical reference manual

Energy Technology Data Exchange (ETDEWEB)

1993-11-01

In an evaluation of the Department of Energy (DOE) Occupational Safety and Health programs for government-owned contractor-operated (GOCO) activities, the Department of Labor`s Occupational Safety and Health Administration (OSHA) recommended a technical information exchange program. The intent was to share written safety and health programs, plans, training manuals, and materials within the entire DOE community. The OSH Technical Reference (OTR) helps support the secretary`s response to the OSHA finding by providing a one-stop resource and referral for technical information that relates to safe operations and practice. It also serves as a technical information exchange tool to reference DOE-wide materials pertinent to specific safety topics and, with some modification, as a training aid. The OTR bridges the gap between general safety documents and very specific requirements documents. It is tailored to the DOE community and incorporates DOE field experience.

Enzymatic added extraction and clarification of fruit juices-A review.

Science.gov (United States)

Sharma, Harsh P; Patel, Hiral; Sugandha

2017-04-13

Enzymatic treatment for juice extraction is most commonly used now a days. The enzymatic process is claimed to offer a number of advantages over mechanical-thermal comminution of several fruit pulps. Enzymes are an integral component of modern fruit juice manufacturing and are highly suitable for optimizing processes. Their main purposes are: increase extraction of juice from raw material, increase processing efficiency (pressing, solid settling or removal), and generate a final product that is clear and visually attractive. Juice extraction can be done by using various mechanical processes, which may be achieved through diffusion extraction, decanter centrifuge, screw type juice extractor, fruit pulper and by different types of presses. Enzymatic treatment prior to mechanical extraction significantly improves juice recovery compared to any other extraction process. Enzymatic hydrolysis of the cell walls increases the extraction yield, reducing sugars, soluble dry matter content and galacturonic acid content and titrable acidity of the products. Enzymatic degradation of the biomaterial depends upon the type of enzyme, incubation time, incubation temperature, enzyme concentration, agitation, pH and use of different enzyme combinations. We can conclude from the technical literature that use of the enzymes i.e. cellulases, pectinases, amylases and combination of these enzymes can give better juice yield with superior quality of the fruit juice. Pectinase enzyme can give maximum juice yield i.e. 92.4% at 360 minutes incubation time, 37°C incubation temperature and 5 mg/100 g of enzyme concentration. Whereas the combination of two enzymes i.e. pectin methyl esterase (PME) and polygalacturonase (PG) at 120 minutes of incubation time, 50°C of incubation temperature and 0.05 mg/100 gm of enzymatic concentration can give the maximum yield of 96.8% for plum fruits. This paper discusses the use of enzymes in fruit juice production focusing on the juice recovery

Biological reductive dechlorination of tetrachloroethylene and trichloroethylene to ethylene under methanogenic conditions

International Nuclear Information System (INIS)

Freedman, D.L.; Gossett, J.M.

1989-01-01

A biological process for remediation of groundwater contaminated with tetrachloroethylene (PCE) and trichloroethylene (TCE) can only be applied if the transformation products are environmentally acceptable. Studies with enrichment cultures of PCE- and TCE-degrading microorganisms provide evidence that, under methanogenic conditions, mixed cultures are able to completely dechlorinate PCE and TCE to ethylene, a product which is environmentally acceptable. Radiotracer studies with [ 14 C]PCE indicated that [ 14 C]ethylene was the terminal product; significant conversion to 14 CO 2 or 14 CH 4 was not observed. The rate-limiting step in the pathway appeared to be conversion of vinyl chloride to ethylene. To sustain reductive dechlorination of PCE and TCE, it was necessary to supply an electron donor; methanol was the most effective, although hydrogen, formate, acetate, and glucose also served. Studies with the inhibitor 2-bromoethanesulfonate suggested that methanogens played a key role in the observed biotransformations of PCE and TCE

Numerical modeling of the Linac4 negative ion source extraction region by 3D PIC-MCC code ONIX

CERN Document Server

Mochalskyy, S; Minea, T; Lifschitz, AF; Schmitzer, C; Midttun, O; Steyaert, D

2013-01-01

At CERN, a high performance negative ion (NI) source is required for the 160 MeV H- linear accelerator Linac4. The source is planned to produce 80 mA of H- with an emittance of 0.25 mm mradN-RMS which is technically and scientifically very challenging. The optimization of the NI source requires a deep understanding of the underling physics concerning the production and extraction of the negative ions. The extraction mechanism from the negative ion source is complex involving a magnetic filter in order to cool down electrons’ temperature. The ONIX (Orsay Negative Ion eXtraction) code is used to address this problem. The ONIX is a selfconsistent 3D electrostatic code using Particles-in-Cell Monte Carlo Collisions (PIC-MCC) approach. It was written to handle the complex boundary conditions between plasma, source walls, and beam formation at the extraction hole. Both, the positive extraction potential (25kV) and the magnetic field map are taken from the experimental set-up, in construction at CERN. This contrib...

The logic of Technical Standardisation

DEFF Research Database (Denmark)

Nedergaard, Peter

In this paper technical standardisation is understood and explained in a model where economic analysis is coupled with an analysis of the political system as proposed in rational choice theory. The aim is to answer both the question why various countries (e.g. the United States versus European...... countries) let either the market or public intervention determine the mode of technical standardisation and the possible implications of these two ways of organizing technical standardisation from an economic and a political point of view. Based upon the analysis of the paper a couple of general policy...... recommendations are made concerning the mode of technical standardisation....

How to be an Effective Technical Writer?

Directory of Open Access Journals (Sweden)

M Solaiman Ali

2012-07-01

Full Text Available Abstract--This paper has focused on technical writing as a skill for engineers. It has sought to define technical writing and throw light on the content and technique of writing the various components of successful technical reports (for example, articles, papers, or research reports, such as theses and dissertations. Then, it has highlighted other special features and principles of effective technical writing. The material in this paper is divided into seven major parts. Part 1 (Technical writing for engineers stresses that a successful engineering career requires strong writing skills. Part 2 (How to write the major sections or elements of a report describes the techniques of writing the abstract, introduction, literature review, procedure/methods & materials, results, discussion, conclusion, and recommendations. Part 3 (Special features of technical writing brings into focus some of the special features of technical writing such as tables & graphs in the text, graphics in instructions, team writing, ethics (plagiarism, document sources, three citation styles and IEEE reference style. Part 4 (Technical usage deals with writing abbreviations, initialisms and acronyms, numbers, units of measurement, and equations.Part 5 (Technical style highlights the imperative writing style and other features of technical writing such as the use of active and passive voices, plain vs. complex syntax, avoiding redundant or superfluous expressions, and vague generalities, using words or expressions with visual impact, the past tense to describe experimental work, the present tense to describe hypotheses, principles, theories and truths, and breaking up the text of the report into short sections. Part 6 (Document specifications emphasizes the technical writer’s need to conform to such document specifications as word count, format, font, number of words per line of text imposed. Part 7 (Reader-friendly technical writing suggests choosing the varied writing modes

Mechanical Engineering Department technical abstracts

International Nuclear Information System (INIS)

Denney, R.M.

1982-01-01

The Mechanical Engineering Department publishes listings of technical abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). Overall information about current activities of each of the Department's seven divisions precedes the technical abstracts

A critical review on the spray drying of fruit extract: effect of additives on physicochemical properties.

Science.gov (United States)

Krishnaiah, Duduku; Nithyanandam, Rajesh; Sarbatly, Rosalam

2014-01-01

Spray drying accomplishes drying while particles are suspended in the air and is one method in the family of suspended particle processing systems, along with fluid-bed drying, flash drying, spray granulation, spray agglomeration, spray reaction, spray cooling, and spray absorption. This drying process is unique because it involves both particle formation and drying. The present paper reviews spray drying of fruit extracts, such as acai, acerola pomace, gac, mango, orange, cactus pear, opuntia stricta fruit, watermelon, and durian, and the effects of additives on physicochemical properties such as antioxidant activity, total carotenoid content, lycopene and β-carotene content, hygroscopy, moisture content, volatile retention, stickiness, color, solubility, glass transition temperature, bulk density, rehydration, caking, appearance under electron microscopy, and X-ray powder diffraction. The literature clearly demonstrates that the effect of additives and encapsulation play a vital role in determining the physicochemical properties of fruit extract powder. The technical difficulties in spray drying of fruit extracts can be overcome by modifying the spray dryer design. It also reveals that spray drying is a novel technology for converting fruit extract into powder form.

RNA-seq: technical variability and sampling

Science.gov (United States)

2011-01-01

Background RNA-seq is revolutionizing the way we study transcriptomes. mRNA can be surveyed without prior knowledge of gene transcripts. Alternative splicing of transcript isoforms and the identification of previously unknown exons are being reported. Initial reports of differences in exon usage, and splicing between samples as well as quantitative differences among samples are beginning to surface. Biological variation has been reported to be larger than technical variation. In addition, technical variation has been reported to be in line with expectations due to random sampling. However, strategies for dealing with technical variation will differ depending on the magnitude. The size of technical variance, and the role of sampling are examined in this manuscript. Results In this study three independent Solexa/Illumina experiments containing technical replicates are analyzed. When coverage is low, large disagreements between technical replicates are apparent. Exon detection between technical replicates is highly variable when the coverage is less than 5 reads per nucleotide and estimates of gene expression are more likely to disagree when coverage is low. Although large disagreements in the estimates of expression are observed at all levels of coverage. Conclusions Technical variability is too high to ignore. Technical variability results in inconsistent detection of exons at low levels of coverage. Further, the estimate of the relative abundance of a transcript can substantially disagree, even when coverage levels are high. This may be due to the low sampling fraction and if so, it will persist as an issue needing to be addressed in experimental design even as the next wave of technology produces larger numbers of reads. We provide practical recommendations for dealing with the technical variability, without dramatic cost increases. PMID:21645359

Altered functional connectivity to stressful stimuli in prenatally cocaine-exposed adolescents.

Science.gov (United States)

Zakiniaeiz, Yasmin; Yip, Sarah W; Balodis, Iris M; Lacadie, Cheryl M; Scheinost, Dustin; Constable, R Todd; Mayes, Linda C; Sinha, Rajita; Potenza, Marc N

2017-11-01

Prenatal cocaine exposure (PCE) is linked to addiction and obesity vulnerability. Neural responses to stressful and appetitive cues in adolescents with PCE versus those without have been differentially linked to substance-use initiation. However, no prior studies have assessed cue-reactivity responses among PCE adolescents using a connectivity-based approach. Twenty-two PCE and 22 non-prenatally drug-exposed (NDE) age-, sex-, IQ- and BMI-matched adolescents participated in individualized guided imagery with appetitive (favorite-food), stressful and neutral-relaxing cue scripts during functional magnetic resonance imaging. Subjective favorite-food craving scores were collected before and after script exposure. A data-driven voxel-wise intrinsic connectivity distribution analysis was used to identify between-group differences and examine relationships with craving scores. A group-by-cue interaction effect identified a parietal lobe cluster where PCE versus NDE adolescents showed less connectivity during stressful and more connectivity during neutral-relaxing conditions. Follow-up seed-based connectivity analyses revealed that, among PCE adolescents, the parietal seed was positively connected to inferior parietal and sensory areas and negatively connected to corticolimbic during both stress and neutral-relaxing conditions. For NDE, greater parietal connectivity to parietal, cingulate and sensory areas and lesser parietal connectivity to medial prefrontal areas were found during stress compared to neutral-relaxing cueing. Craving scores inversely correlated with corticolimbic connectivity in PCE, but not NDE adolescents, during the favorite-food condition. Findings from this first data-driven intrinsic connectivity analysis of PCE influences on adolescent brain function indicate differences relating to PCE status and craving. These findings provide insight into the developmental impact of in utero drug exposure. Copyright © 2017 Elsevier B.V. All rights reserved.

Who recognises technical standards in TTIP?

NARCIS (Netherlands)

Purnhagen, K.

2018-01-01

Current political discussions on the relationship of technical standards to the Transatlantic, Trade and Investment Partnership (TTIP) concern the question whether TTIP can provide a transatlantic level playing field for technical standards, and whether this will negatively affect technical

Efficient and Air-Stable Planar Perovskite Solar Cells Formed on Graphene-Oxide-Modified PEDOT:PSS Hole Transport Layer

Science.gov (United States)

Luo, Hui; Lin, Xuanhuai; Hou, Xian; Pan, Likun; Huang, Sumei; Chen, Xiaohong

2017-10-01

As a hole transport layer, PEDOT:PSS usually limits the stability and efficiency of perovskite solar cells (PSCs) due to its hygroscopic nature and inability to block electrons. Here, a graphene-oxide (GO)-modified PEDOT:PSS hole transport layer was fabricated by spin-coating a GO solution onto the PEDOT:PSS surface. PSCs fabricated on a GO-modified PEDOT:PSS layer exhibited a power conversion efficiency (PCE) of 15.34%, which is higher than 11.90% of PSCs with the PEDOT:PSS layer. Furthermore, the stability of the PSCs was significantly improved, with the PCE remaining at 83.5% of the initial PCE values after aging for 39 days in air. The hygroscopic PSS material at the PEDOT:PSS surface was partly removed during spin-coating with the GO solution, which improves the moisture resistance and decreases the contact barrier between the hole transport layer and perovskite layer. The scattered distribution of the GO at the PEDOT:PSS surface exhibits superior wettability, which helps to form a high-quality perovskite layer with better crystallinity and fewer pin holes. Furthermore, the hole extraction selectivity of the GO further inhibits the carrier recombination at the interface between the perovskite and PEDOT:PSS layers. Therefore, the cooperative interactions of these factors greatly improve the light absorption of the perovskite layer, the carrier transport and collection abilities of the PSCs, and especially the stability of the cells.

Technical Report for a Study on the Improvement of Extraction Process and Physiological Activities of Polysaccharides from Undaria pinnatifida by Gamma Irradiation

International Nuclear Information System (INIS)

Choi, Jong Il; Lee, Ju Won; Kim, Jae Hun; Yoon, Yo Han; Song, Beom Seok; Yoon, Min Chul; Sung, Nak Yun; Lee, Hak Jyung

2010-06-01

By reason of Undaria pinnatifida growth is temperature dependent, U. pinnatifida produced in April and May are obtained as the main byproducts and it is normally wasted. The objective of the this study was investigated to the improvement of extraction process and physiological activities of polysaccharides from U. pinnatifida by gamma irradiation. The extraction yield of fucoidan and laminarrin was increased by gamma irradiation, and the molecular weight of extracted polysaccharides was decreased by irradiation. The effect of gamma irradiation on storage of U. pinnatifida was investigated. No viable cells were observed in samples irradiated at 3 and 5 kGy. Finally, fucoidan and laminarin were applied in the pork patty, and it was shown that lower lipid oxidation and positive effect on microbial stability and quality of the pork patty. These results will suggest that radiation technology can be applied for the extraction of functional materials and storages safe of the seaweeds

Energy saving in the design and operation of fans; The development of technical literature for the specification of fume extraction systems

Energy Technology Data Exchange (ETDEWEB)

Gibbons, A [Plastic Fabrications and Environmental Technology Ltd., Armagh, Northern Ireland (United Kingdom)

1995-12-01

The processes involved in producing technical literature to assist in the selection of fans are discussed. Desktop publishing has been found to provide an effective method of matching the detail of the literature to the needs of the customer. (author)

Simulations of Various Driving Mechanisms for the 3rd Order Resonant Extraction from the MedAustron Medical Synchrotron

CERN Document Server

Feldbauer, G; Dorda, U

2011-01-01

The MedAustron medical synchrotron is based on the CERN-PIMMS design and its technical implementation by CNAO [1]. This document elaborates on studies performed on the baseline betatron-core driven extraction method and investigates the feasibility of alternative resonance driving mechanisms like RF-knockout, RF-noise and the lattice tune. Single particle tracking results are presented, explained and compared to analytical results.

Effects of prenatal caffeine exposure on glucose homeostasis of adult offspring rats

Science.gov (United States)

Kou, Hao; Wang, Gui-hua; Pei, Lin-guo; Zhang, Li; Shi, Chai; Guo, Yu; Wu, Dong-fang; Wang, Hui

2017-12-01

Epidemiological evidences show that prenatal caffeine exposure (PCE) could induce intrauterine growth retardation (IUGR). The IUGR offspring also present glucose intolerance and type 2 diabetes mellitus after maturity. We have previously demonstrated that PCE induced IUGR and increased susceptibility to adult metabolic syndrome in rats. This study aimed to further investigate the effects of PCE on glucose homeostasis in adult offspring rats. Pregnant rats were administered caffeine (120 mg/kg/day, intragastrically) from gestational days 11 to 20. PCE offspring presented partial catch-up growth pattern after birth, characterizing by the increased body weight gain rates. Meanwhile, PCE had no significant influences on the basal blood glucose and insulin phenotypes of adult offspring but increased the glucose tolerance, glucose-stimulated insulin section and β cell sensitivity to glucose in female progeny. The insulin sensitivity of both male and female PCE offspring were enhanced accompanied with reduced β cell fraction and mass. Western blotting results revealed that significant augmentation in protein expression of hepatic insulin signaling elements of PCE females, including insulin receptor (INSR), insulin receptor substrate 1 (IRS-1) and the phosphorylation of serine-threonine protein kinase (Akt), was also potentiated. In conclusion, we demonstrated that PCE reduced the pancreatic β mass but increased the glucose tolerance in adult offspring rats, especially for females. The adaptive compensatory enhancement of β cell responsiveness to glucose and elevated insulin sensitivity mainly mediated by upregulated hepatic insulin signaling might coordinately contribute to the increased glucose tolerance.

Comparison of mentha extracts obtained by different extraction methods

Directory of Open Access Journals (Sweden)

Milić Slavica

2006-01-01

Full Text Available The different methods of mentha extraction, such as steam distillation, extraction by methylene chloride (Soxhlet extraction and supercritical fluid extraction (SFE by carbon dioxide (CO J were investigated. SFE by CO, was performed at pressure of 100 bar and temperature of40°C. The extraction yield, as well as qualitative and quantitative composition of obtained extracts, determined by GC-MS method, were compared.

Technical innovation and policy of scientific technique

International Nuclear Information System (INIS)

Song, Wi Jin

2006-04-01

This book deals with system of innovation and policy of scientific technology : main view point and Topic, technical politics and technical learning, spread of internet and change of structure in information and communications industry, characteristic of technical innovation of software as open source, transfer into national innovation system, change of activity of public scientific technology, theory on technical innovation, evolution of technical innovation policy and participation of civil.

Improving the extraction-and-loading process in the open mining operations

Directory of Open Access Journals (Sweden)

Cheban A. Yu.

2017-09-01

Full Text Available Using the explosions is the main way to prepare solid rocks for the excavation, and that results in the formation of a rock mass of uneven granulometric composition, which makes it impossible to use a conveyor quarry transport without the preliminary large crushing of the rock mass obtained during the explosion. A way to achieve the greatest technical and economic effect is the full conveyorization of quarry transport, what, in this case, ensures the sequenced-flow of transport operations, automation of management and high labor productivity. The extraction-and-loading machines are the determining factor in the performance of mining and transport machines in the technological flow of the quarry. When extracting a blasted rock mass with single-bucket excavators or loaders working in combination with bottom-hole conveyors, one uses self-propelled crushing and reloading units of various designs to grind large individual parts to fractions of conditioning size. The presence of a crushing and reloading unit in the pit-face along with the excavator requires an additional space for its placement, complicates the maneuvering of the equipment in the pit-face, and increases the number of personnel and the cost of maintaining the extraction-and-reloading operations. The article proposes an improved method for carrying out the extraction-and-loading process, as well as the design of extraction-and-grinding unit based on a quarry hydraulic excavator. The design of the proposed unit makes it possible to convert the cyclic process of scooping the rock mass into the continuous process of its loading on the bottom-hole conveyor. Using the extraction-and-grinding unit allows one to combine the processes of excavation, preliminary crushing and loading of the rock mass, which ensures an increase in the efficiency of mining operations.

Talent management : Retaining and managing technical specialists in a technical career

OpenAIRE

Brunila, Alexandra; Baedecke Yllner, Emelie

2013-01-01

The purpose of this thesis is to investigate talent management and how companies should work with talent management in order to retain and manage technical specialists in a technical career. Talent management is found to be important for modern organizations because of the advent of the knowledge economy, new generations entering the workforce and the need for businesses to become more strategic and competitive, which implies new ways of managing human capital. Furthermore, talent management ...

Towards common technical standards

International Nuclear Information System (INIS)

Rahmat, H.; Suardi, A.R.

1993-01-01

In 1989, PETRONAS launched its Total Quality Management (TQM) program. In the same year the decision was taken by the PETRONAS Management to introduce common technical standards group wide. These standards apply to the design, construction, operation and maintenance of all PETRONAS installations in the upstream, downstream and petrochemical sectors. The introduction of common company standards is seen as part of an overall technical management system, which is an integral part of Total Quality Management. The Engineering and Safety Unit in the PETRONAS Central Office in Kuala Lumpur has been charged with the task of putting in place a set of technical standards throughout PETRONAS and its operating units

Radiographic technical quality of root canal treatment performed ex vivo by dental students at Valencia University Medical and Dental School, Spain

Science.gov (United States)

Faus-Matoses, Vicente; Alegre-Domingo, Teresa; Faus-Llácer, Vicente J.

2014-01-01

Objectives: To evaluate radiographically the quality of root canal fillings and compare manual and rotary preparation performed on extracted teeth by undergraduate dental students. Study Design: A total of 561 premolars and molars extracted teeth were prepared using nickel-titanium rotary files or manual instrumentation and filled with gutta-percha using a cold lateral condensation technique, by 4th grade undergraduate students. Periapical radiographs were used to assess the technical quality of the root canal filling, evaluating three variables: length, density and taper. These data were recorded, scored and used to study the “technical success rate” and the “overall score”. The length of each root canal filling was classified as acceptable, short and overfilled, based on their relationship with the radiographic apex. Density and taper of filling were evaluated based on the presence of voids and the uniform tapering of the filling, respectively. Statistical analysis was used to evaluate the quality of root canal treatment, considering p rotary instruments (52% against 28% with a manual one, p rotary instrumentation. Key words:Dental education, endodontics, rotary instrumentation, radiographs, root canal treatment, undergraduate students. PMID:24121911

El Salvador - Formal Technical Education

Data.gov (United States)

Millennium Challenge Corporation — With a budget of nearly $20 million, the Formal Technical Education Sub-Activity was designed to strengthen technical and vocational educational institutions in the...

Nonthermal Photocoercivity Effect in a Low-Doped (Ga,Mn)As Ferromagnetic Semiconductor

Science.gov (United States)

Astakhov, G. V.; Hoffmann, H.; Korenev, V. L.; Kiessling, T.; Schwittek, J.; Schott, G. M.; Gould, C.; Ossau, W.; Brunner, K.; Molenkamp, L. W.

2009-05-01

We report a photoinduced change of the coercive field, i.e., a photocoercivity effect (PCE), under very low intensity illumination of a low-doped (Ga,Mn)As ferromagnetic semiconductor. We find a strong correlation between the PCE and the sample resistivity. Spatially resolved dynamics of the magnetization reversal rule out any role of thermal heating in the origin of this PCE, and we propose a mechanism based on the light-induced lowering of the domain wall pinning energy. The PCE is local and reversible, allowing writing and erasing of magnetic images using light.

Would Engineers Need Non-technical Skills or Non-technical Competences or Both?

Directory of Open Access Journals (Sweden)

Velli Parts

2013-04-01

Full Text Available Normal 0 21 MicrosoftInternetExplorer4 Two main competence approaches are under the discussion. There is evidence that graduates do not fully perceive and/or underestimate the influence of non-technical competences on their employability. An understanding of the necessity of non-technical competences develops after a graduate has already been hired and is working at that job.

Ageing management technical information investigations

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

In February 2013, there are 50 units of commercial nuclear power plants (NPPs) in Japan. We enter into a period that 20 units of them are operating for more than 30 years. Currently, regulation imposes utilities to conduct ageing technical evaluations of each unit before operation of 30 years from the commissioning, to develop the long term maintenance management policy for next 10 years and to submit to the regulatory authority the policy with the report on ageing management technical evaluation (AMTE) for each NPP. It is necessary for regulatory side to develop technical information bases incorporating latest technical knowledge as operating experiences in domestic and abroad on ageing of the plants necessary to conduct reviews of AMTE for each unit. Based on these standpoints, technical information bases investigations have been conducted from the viewpoints of material degradation of ageing NPPs. In order to develop scientific regulator judgment bases related to ageing management (AM) and long-term operation (LTO), investigations on latest information on ageing management in domestic and abroad are conducted and a set of documents including technical evaluation review manuals necessary to conduct AMTE are prepared. To utilize the results of the investigations for ageing technical evaluation, database including latest information related to AM and LTO are developed, ran and operated. In addition, investigations related to Fugen nuclear plant, under decommissioning plants, investigations on mechanism of stress corrosion cracking (SCC), thermal ageing and preventive technologies for SCC, detection and diagnosis technology for ageing degradation and condition monitoring technology are performed to validate and confirm effectiveness of the technologies. (author)

Technical functions : a drawbridge between the intentional and structural nature of technical artefacts

NARCIS (Netherlands)

Vermaas, P.E.; Houkes, W.N.

2006-01-01

In this paper we present an action-theoretic account of artefact using and designing and describe our ICE-theory of function ascriptions to technical artefacts. By means of this account and theory we analyse the thesis of the dual nature of technical artefacts according to which descriptions of

PERANCANGAN APLIKASI RENCANA ANGGARAN BIAYA (RAB (STUDI KASUS PADA DINAS PEKERJAAN UMUM KOTA SALATIGA

Directory of Open Access Journals (Sweden)

Adi Nugroho

2009-01-01

Full Text Available Creating Project Cost Estimation (PCE, list of materials and staff requirements of a construction project should be done before do the project itself. This process needs careful and accurate analysis. Until now Dinas Pekerjaan Umum (DPU in Salatiga city still made PCE manually. It needs much of time and lack of accuracy. This article studies about how to design and implements efficient and accurate PCE computer software, especially for building construction and rehabilitation. PCE aplication software will be by using prototyping method. The application is implemented with Java programming language, Object Relational Mapping (ORM Hibernate, database server MySQL Abstract in Bahasa Indonesia: Pembuatan Project Cost Estimation (PCE, daftar kebutuhan material, dan tenaga kerja seharusnya dilakukan sebelum suatu proyek dimulai. Proses ini membutuhkan analisis yang akurat dan berhati-hati. Saat ini Dinas Pekerjaan Umum (DPU Salatiga masih mengerjakannya secara manual, dimana hal ini membutuhkan waktu yang lama dan akurasinya kurang terjamin. Makalah ini membahas tentang perancangan dan pembuatan perangkat lunak komputer PCE yang efisien dan akurat, terutama untuk pembangunan dan perbaikan gedung. Perangkat lunak aplikasi PCE akan dikembangkan menggunakan metoda prototipe. Aplikasi dikembangkan menggunakan bahasa pemrograman Java, Object Relational Mapping (ORM Hibernate, server basis data MySQL. Kata kunci: project cost estimation, konstruksi bangunan dan rehabilitasi, java, hibernate, prototyping

75 FR 19575 - Endangered and Threatened Wildlife and Plants; Revised Critical Habitat for Navarretia fossalis

Science.gov (United States)

2010-04-15

... (PCE 2), and the topography and soils that support ponding during winter and spring months (PCE 3). The... and upland habitats that act as the local watershed (PCE 2), and the topography and soils that support... businesses (13 CFR 121.201). Small businesses include manufacturing and mining concerns with fewer than 500...

BWR feedwater nozzle and control rod drive return line nozzle cracking: resolution of generic technical activity A-10. Technical report

International Nuclear Information System (INIS)

Snaider, R.

1980-11-01

This report summarizes work performed by the NRC staff in the resolution of Generic Technical Activity A-10, 'BWR Nozzle Cracking'. Generic Technical Activity A-10 is one of the generic technical subjects designated as 'unresolved safety issues' pursuant to Section 210 of the Energy Reorganization Act of 1974. The report describes the technical issues, the technical studies and analyses performed by the General Electric Company and the NRC staff, the staff's technical positions based on these studies, and the staff's plans for continued implementation of its technical positions. It also provides information for further work to resolve the non-destructive examination issue

Transformation of technical infrastructure

DEFF Research Database (Denmark)

Nielsen, Susanne Balslev

1998-01-01

article about the need of new planning forums in order to initiate transformations with in management of large technical systems for energy, waste and water supply.......article about the need of new planning forums in order to initiate transformations with in management of large technical systems for energy, waste and water supply....

TRANSLATING SERVICE TECHNICAL PROSE

African Journals Online (AJOL)

language. The Application of Technical Service. Prose. To form a good idea of the appl ication .... cost lives. In this particular domain, translators must have a sound technical ... These semantic ... another language and often, in doing so, changing its meaning. The words ..... He will hand out tasks to each translator and after.

Technical Training for Managers.

Science.gov (United States)

Haverland, Edgar M.

The question has arisen as to what kind of information a manager without extensive technical training needs to learn to supervise effectively. For example, the Nike Hercules fire control platoon leader, usually an officer in his first active duty assignment, seldom has had extensive technical training. Yet he is responsibile for the…

Technical Manual. The ACT®

Science.gov (United States)

ACT, Inc., 2014

2014-01-01

This manual contains technical information about the ACT® college readiness assessment. The principal purpose of this manual is to document the technical characteristics of the ACT in light of its intended purposes. ACT regularly conducts research as part of the ongoing formative evaluation of its programs. The research is intended to ensure that…

49 CFR 845.22 - Technical panel.

Science.gov (United States)

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Technical panel. 845.22 Section 845.22... Technical panel. The Director, Bureau of Accident Investigation, or the Director, Bureau of Field Operations, shall designate members of the Board's technical staff to participate in the hearing and initially...

48 CFR 12.211 - Technical data.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Technical data. 12.211... ACQUISITION OF COMMERCIAL ITEMS Special Requirements for the Acquisition of Commercial Items 12.211 Technical data. Except as provided by agency-specific statutes, the Government shall acquire only the technical...

48 CFR 212.211 - Technical data.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Technical data. 212.211 Section 212.211 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT... Acquisition of Commercial Items 212.211 Technical data. The DoD policy for acquiring technical data for...

7 CFR 3430.55 - Technical reporting.

Science.gov (United States)

2010-01-01

... required to submit other technical reports or submit the CRIS reports more frequently than annually... 7 Agriculture 15 2010-01-01 2010-01-01 false Technical reporting. 3430.55 Section 3430.55... ASSISTANCE PROGRAMS-GENERAL AWARD ADMINISTRATIVE PROVISIONS Post-Award and Closeout § 3430.55 Technical...

How to be an Effective Technical Writer?

OpenAIRE

M Solaiman Ali; Dheya Al-Othmany

2012-01-01

Abstract--This paper has focused on technical writing as a skill for engineers. It has sought to define technical writing and throw light on the content and technique of writing the various components of successful technical reports (for example, articles, papers, or research reports, such as theses and dissertations). Then, it has highlighted other special features and principles of effective technical writing. The material in this paper is divided into seven major parts. Part 1 (Technical w...

The Technical Student Programme draws Norwegians

CERN Multimedia

2005-01-01

Erik Hejne, second from left, Chairman of the Technical Students Committee, and Jens Vigen, who is concerned spefically with Norwegian students at CERN, with some of the Norwegian technical students who arrived at CERN in spring 2005, together with their teachers. From mid-April, CERN's PH and IT Departments are hosting ten Norwegian students from Bergen University College, the Sør-Trøndelag University College and the University of Science and Technology in Trondheim to take part in the Laboratory's Technical Student Programme. The Technical Student Programme is open to students of universities and technical higher education establishments in the Member States who, in the course of their studies, are required to complete a period of professional training in industry or in a laboratory. Around 70 Technical Students come to work at CERN each year. Selected by a committee, they spend between six months and one year with the Organization. The programme is funded by CERN. However, once the Laboratory's quota of...

Mechanical Engineering Department. Technical review

Energy Technology Data Exchange (ETDEWEB)

Simecka, W.B.; Condouris, R.A.; Talaber, C. (eds.)

1980-01-01

The Mechanical Engineering Department Technical Review is published to (1) inform the readers of various technical activities within the Department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical achievements and publication abstracts. The first is divided into eight sections, one for each Division in the Department providing the reader with the names of the personnel and the Division accomplishing the work.

Mechanical engineering department technical review

International Nuclear Information System (INIS)

Carr, R.B.; Denney, R.M.

1981-01-01

The Mechanical Engineering Department Technical Review is published to: (1) inform the readers of various technical activities within the department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical acievements and publication abstracts. The first is divided into eight sections, one for each division in the department providing the reader with the names of the personnel and the division accomplishing the work

Mechanical Engineering Department Technical Review

International Nuclear Information System (INIS)

Carr, R.B.; Denney, R.M.

1981-01-01

The Mechanical Engineering Department Technical Review is published to inform readers of various technical activities within the Department, promote exchange of ideas, and give credit to personnel who are achieving the results. The report is presented in two parts: technical achievements and publication abstracts. The first is divided into seven sections, each of which reports on an engineering division and its specific activities related to nuclear tests, nuclear explosives, weapons, energy systems, engineering sciences, magnetic fusion, and materials fabrication

TECHNICAL CULTURE AND HUMAN AXJOSPHERE

OpenAIRE

­Krystyna Chałas

2014-01-01

Technical culture is the value of each historical period. It is the subject of the ongoing development. While it is a value which is associated with different categories of values, mainly material, cognitive, social. Between culture and these three categories of values ​ there is a cognitive effect. Technical culture determines the quality of human axjosphere. The aim of this study is to show the relationships and dependencies between technical culture and the structures in which a person liv...

Mechanical Engineering Department. Technical review

International Nuclear Information System (INIS)

Simecka, W.B.; Condouris, R.A.; Talaber, C.

1980-01-01

The Mechanical Engineering Department Technical Review is published to (1) inform the readers of various technical activities within the Department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical achievements and publication abstracts. The first is divided into eight sections, one for each Division in the Department providing the reader with the names of the personnel and the Division accomplishing the work

Developing Technical Skill Assessments

Science.gov (United States)

Hyslop, Alisha

2009-01-01

One of the biggest challenges facing the career and technical education (CTE) community as it works to implement the 2006 Perkins Act is responding to more rigorous requirements for reporting on CTE students' technical skill attainment. The U.S. Department of Education suggested in non-regulatory guidance that states and locals use the number of…

The technical report - a necessary evil

International Nuclear Information System (INIS)

Koch, H.

1978-01-01

The article is meant mainly for students and for those starting their working life. First of all, the question is discussed why a technical report ought to be written. The technical report serves to rethink own activities, the documentation of one's own work as regards those who ordered it, and to inform the own organization and third parties of the state of technical development. This is followed by a discussion of the requirements made on a technical report, namely adaptation to the aims to be achieved, a good breakdown of subjects, a good linguistic style, and good graphical representation of results. There are numerous DIN standards which are useful when working out technical reports. The standards are quoted. (orig.) [de

Regulation of palmitoyl-CoA chain elongation by clofibric acid in the liver of Zucker fa/fa rats.

Science.gov (United States)

Toyama, Tomoaki; Kudo, Naomi; Mitsumoto, Atsushi; Kawashima, Yoichi

2005-05-01

The regulation of palmitoyl-CoA chain elongation (PCE) by clofibric acid [2-(4-chlorophenoxy)-2-methylpropionic acid] was investigated in comparison with stearoyl-CoA desaturase (SCD) in the liver of obese Zucker fa/fa rats. The proportion of oleic acid in the hepatic lipids of Zucker obese rats is 2.7 times higher than that of lean littermates. The activities of PCE and SCD in the liver of Zucker obese rats were markedly higher than in lean rats, and the hepatic uptake of 2-deoxyglucose (2-DG) was also higher in Zucker obese rats compared with lean rats. The increased activities of SCD and PCE in Zucker obese rats were due to the enhanced expression of mRNA of both SCD1 and rat FA elongase 2 (rELO2), but not SCD2 or rELO1. The proportion of oleic acid in the liver was significantly increased by the administration of clofibric acid to Zucker obese rats, and the hepatic PCE activity and rELO2 mRNA expression, but not the SCD activity or SCD1 mRNA expression, were increased in response to clofibric acid treatment. By contrast, the activities of both PCE and SCD and the mRNA expression of SCD1 and rELO2 in the liver were increased by the treatment of Zucker lean rats with clofibric acid. Multiple regression analysis, which was performed to determine the relationships involving PCE activity, SCD activity, and the proportion of oleic acid, revealed that the three parameters were significantly correlated and that the standardized partial regression coefficient of PCE was higher than that of SCD. These results indicate that oleic acid is synthesized by the concerted action of PCE and SCD and that PCE plays a crucial role in the formation of oleic acid when Zucker fa/fa rats are given clofibric acid.

Low functional programming of renal AT2R mediates the developmental origin of glomerulosclerosis in adult offspring induced by prenatal caffeine exposure.

Science.gov (United States)

Ao, Ying; Sun, Zhaoxia; Hu, Shuangshuang; Zuo, Na; Li, Bin; Yang, Shuailong; Xia, Liping; Wu, Yong; Wang, Linlong; He, Zheng; Wang, Hui

2015-09-01

Our previous study has indicated that prenatal caffeine exposure (PCE) could induce intrauterine growth retardation (IUGR) of offspring. Recent research suggested that IUGR is a risk factor for glomerulosclerosis. However, whether PCE could induce glomerulosclerosis and its underlying mechanisms remain unknown. This study aimed to demonstrate the induction to glomerulosclerosis in adult offspring by PCE and its intrauterine programming mechanisms. A rat model of IUGR was established by PCE, male fetuses and adult offspring at the age of postnatal week 24 were euthanized. The results revealed that the adult offspring kidneys in the PCE group exhibited glomerulosclerosis as well as interstitial fibrosis, accompanied by elevated levels of serum creatinine and urine protein. Renal angiotensin II receptor type 2 (AT2R) gene expression in adult offspring was reduced by PCE, whereas the renal angiotensin II receptor type 1a (AT1aR)/AT2R expression ratio was increased. The fetal kidneys in the PCE group displayed an enlarged Bowman's space and a shrunken glomerular tuft, accompanied by a reduced cortex width and an increase in the nephrogenic zone/cortical zone ratio. Observation by electronic microscope revealed structural damage of podocytes; the reduced expression level of podocyte marker genes, nephrin and podocin, was also detected by q-PCR. Moreover, AT2R gene and protein expressions in fetal kidneys were inhibited by PCE, associated with the repression of the gene expression of glial-cell-line-derived neurotrophic factor (GDNF)/tyrosine kinase receptor (c-Ret) signaling pathway. These results demonstrated that PCE could induce dysplasia of fetal kidneys as well as glomerulosclerosis of adult offspring, and the low functional programming of renal AT2R might mediate the developmental origin of adult glomerulosclerosis. Copyright © 2015. Published by Elsevier Inc.

Technical Training: Places available

CERN Multimedia

Monique Duval

2005-01-01

The number of places available may vary. Please check our Web site to find out the current availability. Places are available on the following courses: LabVIEW Real-Time (F) : 7 - 9.6.2005 (3 jours) LabVIEW Migration 6 to 7: 14.6.2005 (1 day) IT3T/1 - Read your mail and more with Outlook 2003 : 14.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/2 - Creating, managing and using distribution lists with Simba2 : 16.6.2005 (IT Technical Training Tutorial, free of charge) FrontPage 2003 - niveau 2 : 16 & 17.6.2005 (2 jours) Utilisation de fichiers PDF avec ACROBAT 6.0 : 20.6.2005 (1journée) Introduction to ANSYS: 21 - 24.6.2005 (4 days) IT3T/3 - Working remotely with Windows XP : 28.6.2005 (IT Technical Training Tutorial, free of charge) IT3T/4 - Editing Websites with Frontpage 2003 : 30.6.2005 (IT Technical Training Tutorial, free of charge) WORD 2003 (Short Course I) - HowTo... Work with repetitive tasks /AutoText, AutoFormat, AutoC...

New usable technical specifications

International Nuclear Information System (INIS)

Webster, S.A.; Tomasi, L.T.; Bernier, R.A.

1989-01-01

After 2 yr of preparation, 1988 finally saw the nuclear industry writing operator-oriented technical specifications. This effort is a continuation of previous efforts to develop improved and usable standard technical specifications (STSs), and is being conducted by the four nuclear steam supply system vendor owners' groups under the auspices of the Nuclear Management Resources Council. Each participant is currently preparing a set of improved STSs based on a writer's guide that was developed through a combined industry effort. In May of 1987, a Human Factors Improvements to Technical Specifications (HFITS) task group was formed to prepare a writer's guide for improved, industrywide STSs. This task group was composed of two representatives from each owners' group, one with a human factors background and one with some operations background. Two documents were prepared in 6 months, a human factors report laying the groundwork for the considerations to go into technical specifications and a writer's guide for their preparation. This paper reports on the application of this writer's guide to the writing of improved STS

46 CFR 160.066-13 - Technical tests.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Technical tests. 160.066-13 Section 160.066-13 Shipping....066-13 Technical tests. (a) The following conditions apply to technical tests as described in this... signals are protected by sealed packaging, then the conditioning for the technical tests must be conducted...

Technical note: Characterization of key volatile odorants in rabbit meat using gas chromatography mass spectrometry with simultaneous distillation extraction

Directory of Open Access Journals (Sweden)

Y.J. Xie

2016-12-01

Full Text Available This study explored the key volatile compounds in both male and female rabbit meat. Simultaneous distillation extraction with dichloromethane was adopted to extract the volatile compounds in Hyla rabbit meat. A total of 35 volatile compounds were identified by gas chromatography–mass spectrometry and quantified with 2, 4, 6-thimethylpyridine as internal standard. Seventeen volatile aldehydes, 4 alcohols, 2 ketones, 2 acids, 1 heterocyclic compound, 2 alkanes and 7 esters were detected. Hexanal, heptanal, octanal, nonanal, (E, E-2, 4-decadienal, 1-octen-3-ol and (Z-2-decenal were the key odorant compounds, with high relative odour activity value. Furthermore, the concentration of volatile compounds in male rabbit meat was higher than that in female rabbit meat.

Problems of technical cooperation

International Nuclear Information System (INIS)

Noramli, M.

1987-01-01

The main principles of the IAEA technical co-operation program, which intends to answer the requirements of the member states as regards technical assistance, are presented. IAEA offers its assistance in the supervision and financial support of the projects, which promise direct and quick profit to the member states. Projects related to the satisfaction of the main demands of humanity, industrial use, energy generation, radiation protection and other fields, which can promote the contribution of nuclear power generation to the course of peace, protection of health and thriving of states, are among them. 35 million dollars (USA) was allocated for the IAEA technical assistance and realization of the co-operation program in 1987

The Technical Communicator as Advocate: Integrating a Social Justice Approach in Technical Communication

Science.gov (United States)

Jones, Natasha N.

2016-01-01

This article argues for the need for a social justice approach to technical communication research and pedagogy. Given previous calls by scholars in technical and professional communication (TPC) for an attention to diversity, inclusion, and equality, the author examines the place and purpose of social justice in TPC and provides useful approaches…

Psychopathology and special education enrollment in children with prenatal cocaine exposure.

Science.gov (United States)

Levine, Todd P; Lester, Barry; Lagasse, Linda; Shankaran, Seetha; Bada, Henrietta S; Bauer, Charles R; Whitaker, Toni M; Higgins, Rosemary; Hammond, Jane; Roberts, Mary B

2012-06-01

This study evaluated how enrollment in special education services in 11-year-old children relates to prenatal cocaine exposure (PCE), psychopathology, and other risk factors. Participants were 498 children enrolled in The Maternal Lifestyle Study, a prospective, longitudinal, multisite study examining outcomes of children with PCE. Logistic regression was used to examine the effect of PCE and psychopathology on enrollment in an individualized education plan (IEP; a designation specific to children with special education needs), with environmental, maternal, and infant medical variables as covariates. PCE, an interaction of PCE and oppositional defiant disorder, child attention-deficit hyperactivity disorder, parent-reported internalizing behaviors, and teacher-reported externalizing behaviors, predicted enrollment in an IEP. Other statistically significant variables in the model were male gender, low birth weight, being small for gestational age, white race, caregiver change, low socioeconomic status, low child intelligence quotient, caregiver depression, and prenatal marijuana exposure. PCE increased the likelihood of receiving an IEP with adjustment for covariates. Psychopathology also predicted this special education outcome, in combination with and independent of prenatal cocaine exposure.

32 CFR 701.38 - Technical data.

Science.gov (United States)

2010-07-01

... 32 National Defense 5 2010-07-01 2010-07-01 false Technical data. 701.38 Section 701.38 National... DOCUMENTS AFFECTING THE PUBLIC FOIA Definitions and Terms § 701.38 Technical data. Recorded information, regardless of form or method of the recording, of a scientific or technical nature (including computer...

Research in Technical Colleges

Science.gov (United States)

MacLennan, A.

2008-01-01

Purpose: The purpose of this paper is to list and demonstrate areas in which research needs to be carried out, or questions answered, in order to raise the quality of technical education. Design/methodology/approach: The area of technical education expanded very rapidly in the late 1950s, and there was little comprehensive knowledge regarding the…

The story of technical cooperation

International Nuclear Information System (INIS)

Park, Yang Taek

1989-09-01

This book gives descriptions of technical cooperation, which is about why does technology transfer?, process of technology transfer with model, decisive cause and cooperation of technology transfer, cost and effect of technology transfer, historical experience of technology transfer, cases of technology transfer by field such as rubber tire, medicine and computer industry and automobile industry, technology transfer process and present condition of technical cooperation, and strategy for rising of technical cooperation : selection of technology for object of cooperation and development of human resources.

World Wide Comparism of Technical and Vocational Education: Lessons for Nigerian Technical and Vocational Education Sector (I)

Science.gov (United States)

Ayeni, Abiodun Olumide

2015-01-01

This paper compared technical/vocational education in: Germany, Australia, Finland, Hong Kong, Hungary, India, Japan, South Korea, Mexico, and Nigeria, and found that technical/vocational education was given proper attention in countries considered except Nigeria, where it was handled with laissez faire attitude. Set-Up of Technical/Vocational…

25 CFR 41.10 - Technical assistance.

Science.gov (United States)

2010-04-01

... Community College's request in writing. In any case, where the type and source of technical assistance is... for technical assistance under this section shall be made in writing and sent to the applicant within... 25 Indians 1 2010-04-01 2010-04-01 false Technical assistance. 41.10 Section 41.10 Indians BUREAU...

15 CFR 911.8 - Technical requirements.

Science.gov (United States)

2010-01-01

... PROCEDURES CONCERNING USE OF THE NOAA SPACE-BASED DATA COLLECTION SYSTEMS § 911.8 Technical requirements. (a) All platform operators of the NOAA DCS must use a data collection platform radio set whose technical... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Technical requirements. 911.8 Section...

TECHNICAL EFFICIENCY AND TECHNICAL LEVEL INDICATORS APPLICATION FOR CIVIL AIRCRAFT FUNCTIONAL PROPERTIES ANALYSIS

Directory of Open Access Journals (Sweden)

Vadim V. Efimov

2018-01-01

Full Text Available Functional properties characterize the purpose of the aircraft and are described by its flight performance characteristics such as range and cruising speed, payload, runway characteristics, etc. Functional properties also characterize the aircraft efficiency that determines the objective need for their analysis by both aircraft designers and operators in conditions of permanent and systematic efficiency increase necessity. When choosing the aircraft, it is important for the operator to make sure that a selected aircraft type has a high level of functional properties, which will allow it to provide high operational efficiency without obsolescence in the long term. However, when choosing from several aircraft types the operator has to face the fact that some characteristics of considered aircraft variants are better and the others are worse that does not allow to definitely determine what aircraft type has a higher level of functional properties.The possibility of applying technical efficiency indicators and a generalized technical level indicator for analyzing the functional properties of civil aviation aircraft is explored in this article. Fuel, weight and target efficiency values as well as the previously improved technical level indicator value were calculated for the different generations and modifications of Boeing 737 and Airbus A320 families of medium-range airplanes, which was followed by the results interpretation within one airplane generation and when moving historically from one airplane generation to another. According to analysis results it is concluded that it is impossible to define the change of the aircraft functional properties level by the change in the values of separate technical efficiency indicators. Thus, it is proposed to use a generalized technical level indicator that determines the level of aircraft technical perfection for purpose and to use efficiency indicators to analyze the cost of providing this level of

Technical Proposal Salton Sea Geothermal Power Pilot Plant Program

Energy Technology Data Exchange (ETDEWEB)

None

1975-03-28

The proposed Salton Sea Geothermal Power Pilot Plant Program comprises two phases. The objective of Phase 1 is to develop the technology for power generation from high-temperature, high-salinity geothermal brines existing in the Salton Sea known geothermal resources area. Phase 1 work will result in the following: (a) Completion of a preliminary design and cost estimate for a pilot geothermal brine utilization facility. (b) Design and construction of an Area Resource Test Facility (ARTF) in which developmental geothermal utilization concepts can be tested and evaluated. Program efforts will be divided into four sub-programs; Power Generation, Mineral Extraction, Reservoir Production, and the Area Resources Test Facility. The Power Generation Subprogram will include testing of scale and corrosion control methods, and critical power cycle components; power cycle selection based on an optimization of technical, environmental and economic analyses of candidate cycles; preliminary design of a pilot geothermal-electric generating station to be constructed in Phase 2 of this program. The Mineral Extraction Subprogram will involve the following: selection of an optimum mineral recovery process; recommendation of a brine clean-up process for well injection enhancement; engineering, construction and operation of mineral recovery and brine clean-up facilities; analysis of facility operating results from environmental, economical and technical point-of-view; preliminary design of mineral recovery and brine clean-up facilities of sufficient size to match the planned pilot power plant. The Reservoir Production Subprogram will include monitoring the operation and maintenance of brine production, handling and injection systems which were built with private funding in phase 0, and monitoring of the brine characteristics and potential subsidence effects during well production and injection. Based on the above, recommendations and specifications will be prepared for production and

Technical Assistance Needs Assessments (TANAs)

Science.gov (United States)

The Technical Assistance Needs Assessment (TANA) is a process to identify whether a community requires additional support from EPA in order to understand technical information and have meaningful participation in the Superfund decision-making process.

Determination of Wastewater Compounds in Sediment and Soil by Pressurized Solvent Extraction, Solid-Phase Extraction, and Capillary-Column Gas Chromatography/Mass Spectrometry

Science.gov (United States)

Burkhardt, Mark R.; Zaugg, Steven D.; Smith, Steven G.; ReVello, Rhiannon C.

2006-01-01

(greater than 25 percent relative standard deviation), (2) reference standards prepared from technical mixtures, or (3) potential blank contamination. Samples were preserved by freezing to -20 degrees Celsius. The U.S. Geological Survey National Water Quality Laboratory has established a 1-year sample-holding time limit (prior to sample extraction) from the date of sample collection (if the sample is kept at -20?C) until a statistically accepted method can be used to determine the effectiveness of the sample-freezing procedure.

Head Start Impact Study. Technical Report

Science.gov (United States)

Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

2010-01-01

This Technical Report is designed to provide technical detail to support the analysis and findings presented in the "Head Start Impact Study Final Report" (U.S. Department of Health and Human Services, January 2010). Chapter 1 provides an overview of the Head Start Impact Study and its findings. Chapter 2 provides technical information on the…

Solvent extraction

Energy Technology Data Exchange (ETDEWEB)

Coombs, D.M.; Latimer, E.G.

1988-01-05

It is an object of this invention to provide for the demetallization and general upgrading of heavy oil via a solvent extracton process, and to improve the efficiency of solvent extraction operations. The yield and demetallization of product oil form heavy high-metal content oil is maximized by solvent extractions which employ either or all of the following techniques: premixing of a minor amount of the solvent with feed and using countercurrent flow for the remaining solvent; use of certain solvent/free ratios; use of segmental baffle tray extraction column internals and the proper extraction column residence time. The solvent premix/countercurrent flow feature of the invention substantially improves extractions where temperatures and pressures above the critical point of the solvent are used. By using this technique, a greater yield of extract oil can be obtained at the same metals content or a lower metals-containing extract oil product can be obtained at the same yield. Furthermore, the premixing of part of the solvent with the feed before countercurrent extraction gives high extract oil yields and high quality demetallization. The solvent/feed ratio features of the invention substanially lower the captial and operating costs for such processes while not suffering a loss in selectivity for metals rejection. The column internals and rsidence time features of the invention further improve the extractor metals rejection at a constant yield or allow for an increase in extract oil yield at a constant extract oil metals content. 13 figs., 3 tabs.

The method for simultaneous extraction and back extraction in liquid three-phase system and equipment for simultaneous extraction and back extraction in liquid three-phase system

International Nuclear Information System (INIS)

Palyska, W.; Chmielewski, A.G.

1992-01-01

The method for simultaneous extraction and back extraction in liquid three-phase system has been worked out. The equipment designed for that process has been also subject of the patent. The interesting component is extracted first to intermediate phase consists of magnetic solvent keeping two extracting phases separately. The intermediate magnetic liquid has been kept in its position using a stable magnet maintained on the surface of the extraction vessel. Then the component pass from intermediate phase to the third phase as a result of back extraction. Mixing in the extraction and back extraction zones is organized by means of rotating shaft going along the whole apparatus. The extraction and back extraction processes occur simultaneously as a result of continuous flow of solvent in their zones. The single extraction back extraction facilities can be joined in larger batteries. 3 figs

Non-technical skills assessment in surgery.

Science.gov (United States)

Sharma, Bharat; Mishra, Amit; Aggarwal, Rajesh; Grantcharov, Teodor P

2011-09-01

Adverse events in surgery have highlighted the importance of non-technical skills, such as communication, decision-making, teamwork, situational awareness and leadership, to effective organizational performance. These skills carry particular importance to surgical oncology, as members of a multidisciplinary team must work cohesively to formulate effective patient care plans. Several non-technical skills evaluation tools have been developed for use in surgery, without adequate comparison and consensus on which should be standard for training. Eleven articles describing the use of three non-technical evaluation tools related to surgery: NOTSS (Non Technical Skills for Surgeons), NOTECHS (Non Technical Skills) and OTAS (Observational Teamwork Assessment for Surgery) were analyzed with respect to scale formulation, validity, reliability and feasibility. Furthermore, their use in training thus far and the future of non-technical rating scales in surgical curricula was discussed. Future work should focus on incorporating these assessment tools into training and into a real operating room setting to provide formative evaluations for surgical residents. Copyright © 2010 Elsevier Ltd. All rights reserved.

School-Camp Project: reflects on teaching, research and academic extension programs in Federal University of Bahia, Brazil; Reflexos do Projeto Campo-Escola no ensino, pesquisa e extensao na Universidade Federal da Bahia

Energy Technology Data Exchange (ETDEWEB)

Oliveira Junior, Jose Baptista de; Santiago, Cybele Celestino; Santanna, Vanessa Cristina [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil)

2008-07-01

In 2003, the Brazilian Regulatory Petroleum Agency (ANP) firmed an agreement with the Federal University of the Bahia (UFBA), transferring to the Polytechnical School the property of five mature fields in Bahia (Quiambina, Fazenda Mamoeiro, Caracatu, Bela Vista and Riacho Sesmaria). The objectives of the agreement, some already reached, were: the revitalization of the fields, the development of technology for gas and oil extraction, the training of professionals. To reach the goals, the Field-School Project (PCE) was created. It is responsible for the control of the activities directly related to the revitalization of the wells. Other activities were also carried out by the PCE: formalization of an agreement between the UFBA and the Brazilian Institute of Oil (IBP) for scientific, academic and cultural activities; creation of a site (www.campoescola.ufba.br), in which interesting information to the oil area is available; consulting to small groups interested in exploring mature fields; increase of resources and job offers to the communities and to the cities near the places were the wells are located; participation in events. (author)

POLYCAPROLACTONE-POLY (ETHYLENE GLYCOL) BLOCK COPOLYMER Ⅲ DRUG RELEASE BEHAVIOR

Institute of Scientific and Technical Information of China (English)

BEI Jianzhong; WANG Zhifeng; WANG Shenguo

1995-01-01

The drug release behavior of degradable polymer - polycaprolactone-poly (ethylene glycol)block copolymer(PCE) in vitro was investigated by using 5-Fluoro-uracil (5-Fu) as a model drug under a condition of pH 7.4 at 37℃. It is found that the release rate of 5-Fu from PCE increased with increasing polyether content of the copolymer. The results show that the increasing polyether content of the copolymer caused increasing hydrophilicity and decreasing crystallinity of the PCE copolymer. Thus, the drug release behavior and the degradable property of the PCE can be controlled by adjusting the composition of the copolymer.

Technical Skill Attainment and Post-Program Outcomes: An Analysis of Pennsylvania Secondary Career and Technical Education Graduates

Science.gov (United States)

Staklis, Sandra; Klein, Steven

2010-01-01

Since the mid-1990s, the Pennsylvania Department of Education (PDE) has required all students concentrating in career and technical education (CTE) programs to complete a standardized technical skill assessment at or near the end of their program. Results of technical skill assessments are used for a number of purposes, including recognizing…

Field convergence between technical writers and technical translators

DEFF Research Database (Denmark)

Gnecchi, M.; Maylath, B.; Mousten, Birthe

2011-01-01

As translation of technical documents continues to grow rapidly and translation becomes more automated, the roles of professional communicators and translators appear to be converging. This paper updates preliminary findings first presented at the 2008 International Professional Communication...

Extractive metallurgy of zirconium--1945 to the present

International Nuclear Information System (INIS)

Franklin, D.G.; Adamson, R.B.

1984-01-01

Although the history of the reduction of zirconium dates from 1824 and the first ductile zirconium metal was produced in the laboratory in 1914, modern reduction practice was pioneered by the U.S. Bureau of Mines starting in 1945. This paper reviews the history of the extractive metallurgy of zirconium from the early work of W. J. Kroll and co-workers at the Bureau of Mines in Albany, Ore., through the commercial development of the production of reactor-grade zirconium metal which was spurred by the requirements of the Naval Reactor Program and the development of commercial nuclear power. Technical subjects covered include processes for opening the ore, zirconium-hafnium separation, chlorination of zirconium oxide, reduction processes, and electrowinning of zirconium metal. Proposed new processes and process modifications are reviewed

Preparation of high purification and food grade phosphoric acid from technical grade phosphoric acid by liquid-liquid detraction method

International Nuclear Information System (INIS)

Alimoradi, M.; Borji, F.; Kishani, A.

2002-01-01

Pay attention to increasing consumption of high purification and food grade phosphoric acid in various industries and food industries and on in on hand and lack of preparation between production and distribution of this products its purification is so vital. In this article of liquid-liquid extraction method with normal hexane-mixture of ammonia and acetone-diisopropyl alcohol and normal butanol solvents and these determination of distribution coefficient each one with ph-me try titration we can evaluate effectiveness and sufficiency each one. Because of proper coefficient distribution and its local production of normal butanol solvent and low price is the best solvent. To phosphoric acid modifying coefficient distribution for extraction of phosphoric acid we can add a little value sulfuric acid to the mixture and to remove flouride impurity we add a little Na 2 O. After extraction stage extracted phosphoric acid in the normal strips by evaluating with distilled water and then by passing the carbon active bed and following passes of cationic resine column and concentrated with vacuum distillation. Conclusion of this article is produce of phosphoric acid 85% w/w and food grade from impure phosphoric acid 52% w/w with technical grade

Technical memory 2007

International Nuclear Information System (INIS)

2009-01-01

The technical memory 2007 of the Nuclear Regulatory Authority (ARN) of the Argentine Republic, compiles the papers published in the subject on radiation protection and nuclear safety, and presented in journals, technical reports, congress or meetings of these specialities by personnel of the mentioned institution during 2007. In this edition the documents are presented on: environmental protection; transport of radioactive materials; regulations; research reactors and nuclear power plants; biological radiation effects; therapeutic uses of ionizing radiation and radioprotection of patients; internal dosimetry; physical dosimetry; knowledge management; radioactive waste management [es

Technical Training: CERN Technical Training 2004: Instructor-led WBTechT Course for Microsoft Applications

CERN Multimedia

2004-01-01

If you wish to participate in one of the following courses, please discuss with your supervisor and apply electronically directly from the course description pages that can be found on the Web at: http://www.cern.ch/Training/ or fill in an "application for training" form available from your Divisional Secretariat or from your DTO (Divisional Training Officer). Applications will be accepted in the order of their receipt. TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch Would you need to enhance your skills in Microsoft Office applications or Outlook? A new "blended learning" course, combining instructor-led and computer-based multimedia training, is now offered by Technical Training: the Instructor-led CERN Web-Based Technical Training (WBTechT) Course for Microsoft Applications. The next session will take place on April 1st, morning. Course sessions will be self-paced and self-directed, with participants being in control of their learning, while ...

ATR Technical Specification Upgrade Program

International Nuclear Information System (INIS)

McCracken, R.T.; Durney, J.L.; Freund, G.A.

1990-01-01

The Advanced Test Reactor (ATR) is a 250 MW, uranium-aluminum fueled test reactor which began full power operation in 1969. The initial operation was controlled by an Operating Limits document based on the original Safety Analysis Report. Additional safety bases were later developed to support Technical Specifications which were approved and implemented in 1977. The Technical Specifications which were initially developed with content and format specified in ANSI/ANS--15.1, ''The Development of Technical Specifications for Research Reactors.'' The safety basis documentation and the Technical Specifications have been updated as required to maintain them current with the ATR facility configuration. All revisions have been made with a content, format and style consistent with the original. A major, two-phase program to upgrade the content, format and style is in progress. This paper describes the first phase of this program

Technical challenges for dismantlement verification

International Nuclear Information System (INIS)

Olinger, C.T.; Stanbro, W.D.; Johnston, R.G.; Nakhleh, C.W.; Dreicer, J.S.

1997-01-01

In preparation for future nuclear arms reduction treaties, including any potential successor treaties to START I and II, the authors have been examining possible methods for bilateral warhead dismantlement verification. Warhead dismantlement verification raises significant challenges in the political, legal, and technical arenas. This discussion will focus on the technical issues raised by warhead arms controls. Technical complications arise from several sources. These will be discussed under the headings of warhead authentication, chain-of-custody, dismantlement verification, non-nuclear component tracking, component monitoring, and irreversibility. The authors will discuss possible technical options to address these challenges as applied to a generic dismantlement and disposition process, in the process identifying limitations and vulnerabilities. They expect that these considerations will play a large role in any future arms reduction effort and, therefore, should be addressed in a timely fashion

Planning wood extraction in a forest coppice

Directory of Open Access Journals (Sweden)

Civitarese V

2006-01-01

Full Text Available A series of cartographic models of analysis have been elaborated through the softwares ArcView GIS (ESRI 2002 and Surfer 8 (Golden software 2002 to find optimal work systems for the wood extraction in an oak coppice, located on the Monti della Tolfa, near Rome, Italy. The main factors analyzed were the morphology of the territory and the roads characteristics. The methodological procedure followed was applied on the different classes of slope, the direction of water outflow, the presence of ditches and channels, the principal and secondary roads, the wood cover and the clearings. The possibility to employ tractors with cages, polyethylene chutes, mules and cable cranes has been examined, also identifying the fittest areas to their use. This first analytical phase was followed by a second phase dedicated to the evaluation of the technical feasibility. The proposed method contributes to a rational planning of the work site. The advantage could be the planning of extraction operations on the map, but it will be necessary to verify the method in field studies. Although this method has been developed on limited extensions of territories, it could be applicable to situations of greater complexity, representing the base for the creation of a tool that may be employed in ampler territorial contexts, such as Comunità Montane and hydrographic basins.

Regulation by carbohydrate and clofibric acid of palmitoyl-CoA chain elongation in the liver of rats.

Science.gov (United States)

Kudo, Naomi; Toyama, Tomoaki; Mitsumoto, Atsushi; Kawashima, Yoichi

2003-05-01

Regulation of palmitoyl-CoA chain elongation (PCE) and its contribution to oleic acid formation were investigated in rat liver in comparison with stearoyl-CoA desaturase (SCD). Hepatic PCE activity was induced by the administration of 20% wt/vol glucose or fructose in the drinking water of normal rats. In streptozotocin-induced diabetic rats, the activities of both PCE and SCD were suppressed, and fructose, but not glucose, feeding caused an increase in the activities of both enzymes. Treatment of normal rats with clofibric acid in combination with carbohydrate further increased PCE, but not SCD, activity. FA analysis of hepatic lipids revealed that the proportion of oleic acid (18:1 n-9) increased upon administration of carbohydrate or clofibric acid. The treatment of rats with clofibric acid in combination with carbohydrate greatly increased the proportion of 18:1 n-9. A significant correlation was observed between PCE activity and the hepatic proportion of 18:1 n-9 (r2 = 0.874, P 0.05). Taken together, these results suggest that carbohydrate induces PCE as well as SCD activity to increase the hepatic 18:1 content in rat liver, and the increased PCE activity seems to be responsible for the further increase in 18:1 n-9 when carbohydrate is administered in combination with clofibric acid.

Ultrasound-Assisted Extraction: Effect of Extraction Time and Solvent ...

African Journals Online (AJOL)

Purpose: To investigate the influence of extraction conditions assisted by ultrasound on the quality of extracts obtained from Mesembryanthemum edule shoots. Methods: The extraction procedure was carried out in an ultrasonic bath. The effect of two solvents (methanol and ethanol) and two extraction times (5 and 10 min) ...

Marketing information: The technical report as product

Science.gov (United States)

Stoher, F. F.; Pinelli, T. E.

1981-01-01

Technical reports constitute a product, the primary means for communicating the results of research to the user. The Langley scientific and technical information (STI) review and evaluation project undertook a review of the technical report as an effective product for information communication. Style manuals describing theory and practice in technical report preparation; publication manuals covering such factors as design, layout, and type style; and copies of technical reports were obtained from industrial, academic, governmental, and research organizations. Based on an analysis of this material, criteria will be established for the report components, for the relationship of the components within the report context, and for the overall report organization. The criteria will be used as bench marks and compared with the publication standards currently used to prepare NASA technical reports.

CH3 NH3 PbI3 and HC(NH2 )2 PbI3 Powders Synthesized from Low-Grade PbI2 : Single Precursor for High-Efficiency Perovskite Solar Cells.

Science.gov (United States)

Zhang, Yong; Kim, Seul-Gi; Lee, Do-Kyoung; Park, Nam-Gyu

2018-05-09

High-efficiency perovskite solar cells are generally fabricated by using highly pure (>99.99 %) PbI 2 mixed with an organic iodide in polar aprotic solvents. However, the use of such an expensive chemical may impede progress toward large-scale industrial applications. Here, we report on the synthesis of perovskite powders by using inexpensive low-grade (99 %) PbI 2 and on the photovoltaic performance of perovskite solar cells prepared from a powder-based single precursor. Pure APbI 3 [A=methylammonium (MA) or formamidinium (FA)] perovskite powders were synthesized by treating low-grade PbI 2 with MAI or FAI in acetonitrile at ambient temperature. The structural phase purity was confirmed by X-ray diffraction. The solar cell with a MAPbI 3 film prepared from the synthesized perovskite powder demonstrated a power conversion efficiency (PCE) of 17.14 %, which is higher than the PCE of MAPbI 3 films prepared by using both MAI and PbI 2 as precursors (PCE=13.09 % for 99 % pure PbI 2 and PCE=16.39 % for 99.9985 % pure PbI 2 ). The synthesized powder showed better absorption and photoluminescence, which were responsible for the better photovoltaic performance. For the FAPbI 3 powder, a solution with a yellow non-perovskite δ-FAPbI 3 powder synthesized at room temperature was found to lead to a black perovskite film, whereas a solution with the black perovskite α-FAPbI 3 powder synthesized at 150 °C was not transformed into a black perovskite film. The α↔δ transition between the powder and film was assumed to correlate with the difference in the iodoplumbates in the powder-dissolved solution. An average PCE of 17.21 % along with a smaller hysteresis [ΔPCE=PCE reverse -PCE forward )=1.53 %] was demonstrated from the perovskite solar cell prepared by using δ-FAPbI 3 powder; this PCE is higher than the average PCE of 17.05 % with a larger hysteresis (ΔPCE=2.71 %) for a device based on a conventional precursor solution dissolving MAI with high

Extraction method

International Nuclear Information System (INIS)

Stary, J.; Kyrs, M.; Navratil, J.; Havelka, S.; Hala, J.

1975-01-01

Definitions of the basic terms and of relations are given and the knowledge is described of the possibilities of the extraction of elements, oxides, covalent-bound halogenides and heteropolyacids. Greatest attention is devoted to the detailed analysis of the extraction of chelates and ion associates using diverse agents. For both types of compounds detailed conditions are given of the separation and the effects of the individual factors are listed. Attention is also devoted to extractions using mixtures of organic agents, the synergic effects thereof, and to extractions in non-aqueous solvents. The effects of radiation on extraction and the main types of apparatus used for extractions carried out in the laboratory are described. (L.K.)

Characterization of an H2-utilizing enrichment culture that reductively dechlorinates tetrachloroethene to vinyl chloride and ethene in the absence of methanogenesis and acetogenesis.

OpenAIRE

Maymó-Gatell, X; Tandoi, V; Gossett, J M; Zinder, S H

1995-01-01

We have been studying an anaerobic enrichment culture which, by using methanol as an electron donor, dechlorinates tetrachloroethene (PCE) to vinyl chloride and ethene. Our previous results indicated that H2 was the direct electron donor for rductive dechlorination of PCE by the methanol-PCE culture. Most-probable-number counts performed on this culture indicated low numbers ( or equal to 10(6)/ml...

Incorporating technical analysis in undergraduate curricula

Directory of Open Access Journals (Sweden)

Michael R. Melton

2017-11-01

Full Text Available Purpose – The purpose of this paper is to introduce instruction of technical analysis on the undergraduate level that can coincide with traditional teachings of fundamental analysis. Design/methodology/approach – Through examples using the latest in security analysis technology, this paper illustrates the importance of technical security analysis. Findings – This research illustrates how technical analysis techniques may be used to make more significant investment decisions. Originality/value – Kirkpatrick and Dahlquist define technical analysis as a security analysis discipline for forecasting future direction of prices through the study of past market data primarily price and volume This form of analysis has stood in direct contrast to the fundamental analysis approach whereby actual facts of the company its industry and sector may be ignored. Understanding this contrast, much of academia has chosen to continue to focus its finance curricula on fundamental analysis techniques. As more universities implement trading rooms to reflect that of industry, they must recognize that any large brokerage trading group or financial institution will typically have both a technical analysis and fundamental analysis team. Thus, the need to incorporate technical analysis into undergraduate finance curricula.

Accelerated Solvent Extraction: An Innovative Sample Extraction Technique for Natural Products

International Nuclear Information System (INIS)

Hazlina Ahmad Hassali; Azfar Hanif Abd Aziz; Rosniza Razali

2015-01-01

Accelerated solvent extraction (ASE) is one of the novel techniques that have been developed for the extraction of phytochemicals from plants in order to shorten the extraction time, decrease the solvent consumption, increase the extraction yield and enhance the quality of extracts. This technique combines elevated temperatures and pressure with liquid solvents. This paper gives a brief overview of accelerated solvent extraction technique for sample preparation and its application to the extraction of natural products. Through practical examples, the effects of operational parameters such as temperature, volume of solvent used, extraction time and extraction yields on the performance of ASE are discussed. It is demonstrated that ASE technique allows reduced solvent consumption and shorter extraction time, while the extraction yields are even higher than those obtained with conventional methods. (author)

EDI and the Technical Communicator.

Science.gov (United States)

Eiler, Mary Ann

1994-01-01

Assesses the role of technical communicators in electronic data interchange (EDI). Argues that, as experts in information design, human factors, instructional theory, and professional writing, technical communicators should be advocates of standard documentation protocols and should rethink the traditional concepts of "document" to…

Extraction process

International Nuclear Information System (INIS)

Rendall, J.S.; Cahalan, M.J.

1979-01-01

A process is described for extracting at least two desired constituents from a mineral, using a liquid reagent which produces the constituents, or compounds thereof, in separable form and independently extracting those constituents, or compounds. The process is especially valuable for the extraction of phosphoric acid and metal values from acidulated phosphate rock, the slurry being contacted with selective extractants for phosphoric acid and metal (e.g. uranium) values. In an example, uranium values are oxidized to uranyl form and extracted using an ion exchange resin. (U.K.)

Towards a method of rapid extraction of strontium-90 from urine: urine pretreatment and alkali metal removal

Energy Technology Data Exchange (ETDEWEB)

Hawkins, C. [Argonne National Lab. (ANL), Argonne, IL (United States); Dietz, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Kaminski, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Mertz, C. [Argonne National Lab. (ANL), Argonne, IL (United States); Shkrob, I. [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-03-01

A technical program to support the Centers of Disease Control and Prevention is being developed to provide an analytical method for rapid extraction of Sr-90 from urine, with the intent of assessing the general population’s exposure during an emergency response to a radiological terrorist event. Results are presented on the progress in urine sample preparation and chemical separation steps that provide an accurate and quantitative detection of Sr-90 based upon an automated column separation sequence and a liquid scintillation assay. Batch extractions were used to evaluate the urine pretreatment and the column separation efficiency and loading capacity based upon commercial, extractant-loaded resins. An efficient pretreatment process for decolorizing and removing organics from urine without measurable loss of radiostrontium from the sample was demonstrated. In addition, the Diphonix® resin shows promise for the removal of high concentrations of common strontium interferents in urine as a first separation step for Sr-90 analysis.

The socio-technical system and nuclear safety

International Nuclear Information System (INIS)

Stefanescu, Petre; Mihailescu, Nicolae; Dragusin, Octavian

1999-01-01

In the field of nuclear safety there have been defined notions like 'technical factors' and 'human factors'. The technical factors depend on designing and manufacturing of components/equipment, actually depend on the people's work. The study of human factors consists in analyzing and recommending the terms that allow an individual to be a reliable and safety agent. Accordingly, he/she is placed in working conditions corresponding to human abilities, associating the means of three levels: - designing, i.e. the action upon the technical system and upon work organization; - correction, i.e. the action upon the evolution of the technical system and organizing; - formation/training, i.e. action upon operators. The paper presents a characterization of the socio-technical system and on this basis discusses the issue of individual adjustment to the socio-technical system and reciprocally, the issue of the socio-technical system adjustment to the individual. Concepts as: ergonomics, physical medium, man/machine interface and support of the operator, man/machine task sharing, the work organizing are put in relation with the central subject, the nuclear safety

48 CFR 435.010 - Scientific and technical reports.

Science.gov (United States)

2010-10-01

... CATEGORIES OF CONTRACTING RESEARCH AND DEVELOPMENT CONTRACTING 435.010 Scientific and technical reports... all scientific and technical reports to the National Technical Information Service at the address... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Scientific and technical...

Improvements mineral dressing and extraction processes of gold-silver ores from San Pedro Frio Mining District, Colombia

International Nuclear Information System (INIS)

Yanez Traslavina, J. J.; Vargas Avila, M. A.; Garcia Paez, I. H.; Pedraza Rosas, J. E.

2005-01-01

The San Pedro Frio district mining, Colombia, is a rich region production gold-silver ores. Nowadays, the extraction processes used are amalgamation, percolation cyanidation and precipitation with zinc wood. Due to the ignorance of the ore characteristics, gold and silver treatment processes are inadequate and not efficient. In addition the inappropriate use of mercury and cyanide cause environmental contamination. In this research the ore characterization was carried out obtained fundamental parameters for the technical selection of more efficient gold and silver extraction processes. Experimental work was addressed to the study of both processes the agitation cyanidation and the adsorption on activated carbon in pulp. As a final result proposed a flowsheet to improve the precious metals recovery and reduce the environment contamination. (Author)

Evaluation of the Webler-Brown model for estimating tetrachloroethylene exposure from vinyl-lined asbestos-cement pipes

Directory of Open Access Journals (Sweden)

Heeren Timothy C

2008-06-01

Full Text Available Abstract Background From May 1968 through March 1980, vinyl-lined asbestos-cement (VL/AC water distribution pipes were installed in New England to avoid taste and odor problems associated with asbestos-cement pipes. The vinyl resin was applied to the inner pipe surface in a solution of tetrachloroethylene (perchloroethylene, PCE. Substantial amounts of PCE remained in the liner and subsequently leached into public drinking water supplies. Methods Once aware of the leaching problem and prior to remediation (April-November 1980, Massachusetts regulators collected drinking water samples from VL/AC pipes to determine the extent and severity of the PCE contamination. This study compares newly obtained historical records of PCE concentrations in water samples (n = 88 with concentrations estimated using an exposure model employed in epidemiologic studies on the cancer risk associated with PCE-contaminated drinking water. The exposure model was developed by Webler and Brown to estimate the mass of PCE delivered to subjects' residences. Results The mean and median measured PCE concentrations in the water samples were 66 and 0.5 μg/L, respectively, and the range extended from non-detectable to 2432 μg/L. The model-generated concentration estimates and water sample concentrations were moderately correlated (Spearman rank correlation coefficient = 0.48, p Conclusion PCE concentration estimates generated using the Webler-Brown model were moderately correlated with measured water concentrations. The present analysis suggests that the exposure assessment process used in prior epidemiological studies could be improved with more accurate characterization of water flow. This study illustrates one method of validating an exposure model in an epidemiological study when historical measurements are not available.

Technical Manual: easyCBM. Technical Report #1408

Science.gov (United States)

Anderson, Daniel; Alonzo, Julie; Tindal, Gerald; Farley, Dan; Irvin, P. Shawn; Lai, Cheng-Fei; Saven, Jessica L.; Wray, Kraig A.

2014-01-01

Since the easyCBM© learning system was first published in 2006, over $8 million of federal funding (both from the Office of Special Education Programs and more recently from the Institute of Education Sciences) has been used to develop, study, and refine the assessments available on the system. This Technical Manual summarizes the ongoing research…

A Procedural Skills OSCE: Assessing Technical and Non-Technical Skills of Internal Medicine Residents

Science.gov (United States)

Pugh, Debra; Hamstra, Stanley J.; Wood, Timothy J.; Humphrey-Murto, Susan; Touchie, Claire; Yudkowsky, Rachel; Bordage, Georges

2015-01-01

Internists are required to perform a number of procedures that require mastery of technical and non-technical skills, however, formal assessment of these skills is often lacking. The purpose of this study was to develop, implement, and gather validity evidence for a procedural skills objective structured clinical examination (PS-OSCE) for internal…

Benzoate-driven dehalogenation of chlorinated ethenes in microbial cultures from a contaminated aquifer

Energy Technology Data Exchange (ETDEWEB)

Bunge, M.; Kleikemper, J.; Miniaci, C.; Duc, L.; Muusse, M.G.; Zeyer, J. [Swiss Federal Institute of Technology (ETH), Zurich (Switzerland). Inst. of Biogeochemistry and Pollutant Dynamics, Soil Biology; Hause, G. [Halle-Wittenberg Univ., Halle (Germany). Biocenter

2007-10-15

Microbial dehalogenation of tetrachloroethene (PCE) and cis-dichloroethene (cis-DCE) was studied in cultures from a continuous stirred tank reactor initially inoculated with aquifer material from a PCE-contaminated site. Cultures amended with hydrogen and acetate readily dechlorinated PCE and cis-DCE; however, this transformation was incomplete and resulted in the accumulation of chlorinated intermediates and only small amounts of ethene within 60 days of incubation. Conversely, microbial PCE and cis-DCE dechlorination in cultures with benzoate and acetate resulted in the complete transformation to ethene within 30 days. Community fingerprinting by denaturing gradient gel electrophoresis (DGGE) revealed the predominance of phylotypes closely affiliated with Desulfitobacterium, Dehalococcoides, and Syntrophus species. The Dehalococcoides culture VZ, obtained from small whitish colonies in cis-DCE dechlorinating agarose cultures, revealed an irregular cell diameter between 200 and 500 nm, and a spherical or biconcave disk-shaped morphology. These organisms were identified as responsible for the dechlorination of cis-DCE to ethene in the PCE-dechlorinating consortia, operating together with the Desulfitobacterium as PCE-to-cis-DCE dehalogenating bacterium and with a Syntrophus species as potential hydrogen-producing partner in cultures with benzoate. (orig.)

ITER technical advisory committee meeting

International Nuclear Information System (INIS)

Fujiwara, M.

1999-01-01

The ITER Technical Advisory Committee (TAC) meeting took place on December 20-22, 1999 at the Naka Joint Work Site. The objective of this meeting was to review the document 'Technical Basis for ITER-FEAT Outline Design (ODR)' issued by the Director on December 10. It was also aimed at providing the ITER Meeting scheduled for January 19-20, 2000 in Tokyo with a technical assessment of ODR and recommendations for the optimization of the anticipated plasma performance and engineering design, based on the guidelines approved by the Council in June 1998 and recommendations of the last TAC meeting

NetView technical research

Science.gov (United States)

1993-01-01

This is the Final Technical Report for the NetView Technical Research task. This report is prepared in accordance with Contract Data Requirements List (CDRL) item A002. NetView assistance was provided and details are presented under the following headings: NetView Management Systems (NMS) project tasks; WBAFB IBM 3090; WPAFB AMDAHL; WPAFB IBM 3084; Hill AFB; McClellan AFB AMDAHL; McClellan AFB IBM 3090; and Warner-Robins AFB.

Adult orthodontic therapy: extraction versus non-extraction.

Science.gov (United States)

Baumrind, S

1998-11-01

This study addresses the problem of randomization of subjects with respect to an irreversible aspect of treatment strategy, namely, the extraction of teeth. The investigation includes both prospective and retrospective components. The data presented focus on clinician decision-making. Of the 1321 potential subjects for whom records were taken, 250 met the inclusion criteria. Of these subjects, 82 declined to participate and 20 were dropped because of difficulty in obtaining five independent evaluations of their records within a reasonable time frame. Thus, the final sample contained 148 subjects. Approximately one-third of the subjects in the sample are adult, somewhat more than half are female, and Class I malocclusions outnumber Class II malocclusions by a count of 95 to 53. Patterns of agreement and disagreement among five clinicians include: a) agreement/disagreement on the primary decision whether or not to extract: the data reveal a strong tendency towards consensus among the clinicians; b) agreement/disagreement on extraction pattern in patients in whom the clinician believes that extraction is indicated: the clinicians tended strongly to agree on extraction pattern; c) agreement/disagreement on the need for adjunctive orthognathic surgery: decisions favoring surgery were more common and more 'definite' than 'probable' in the adult cohort than in the adolescent cohort but this tendency was not as strong as had been anticipated; d) agreement/disagreement concerning Angle classification: disagreements were more common than had been anticipated; and e) differences among the individual clinicians as to their ratios of extraction/non-extraction decisions: overall, clinicians opted for extraction less frequently in the adolescent cohort than in the adult cohort (55 vs. 66%). Because the data are drawn from actual clinical experience, the conclusions involve a number of assumptions and their generalizability should be evaluated.

75 FR 13680 - Commutation of Sentence: Technical Change

Science.gov (United States)

2010-03-23

... Sentence: Technical Change AGENCY: Bureau of Prisons, Justice. ACTION: Interim rule. SUMMARY: This document makes a minor technical change to the Bureau of Prisons (Bureau) regulations on sentence commutation to.... Commutation of Sentence: Technical Change This document makes a minor technical change to the Bureau...

Using mixed solvent and changing spin-coating parameters to increase the efficiency and lifetime of organic solar cells.

Science.gov (United States)

Tsai, Yu Sheng; Chu, Wei-Ping; Tang, Rong-Ming; Juang, Fuh-Shyang; Chang, Ming-Hua; Liu, Mark O; Hsieh, Tsung-Eong

2008-10-01

The derivative of C60, i.e., PCBM, and P3HT (3-hexylthiophene) were dissolved in chloroform:dichlorobenzene mixed solvent, then spin-coated as the active layer for organic solar cells (OSC). The experimental parameters were studied carefully to obtain the optimum power conversion efficiency (PCE), including the solvent mixing ratio, spin-coating speed, annealing conditions for the active layer, etc. The OSC devices were packaged with glass and a newly developed UV-glue to improve the lifetime and PCE. Dichlorobenzene solvent has great effect upon the PCE. Changing the spin-coating speed and increasing the number of steps increased the PCE apparently to 1.4%.

Improvements to Technical Specifications surveillance requirements

International Nuclear Information System (INIS)

Lobel, R.; Tjader, T.R.

1992-12-01

In August 1983 an NRC task group was formed to investigate problems with surveillance testing required by Technical Specifications, and to recommend approaches to effect improvements. NUREG-1024 (''Technical Specifications-Enhancing Safety Impact'') resulted, and it contained recommendations to review the basis for test frequencies; to ensure that the tests promote safety and do not degrade equipment; and to review surveillance tests so that they do not unnecessarily burden personnel. The Technical Specifications Improvement Program (TSIP) was established in December 1984 to provide the framework for rewriting and improving the Technical Specifications. As an element of the TSIP, all Technical Specifications surveillance requirements were comprehensively examined as recommended in NUREG-1024. The results of that effort are presented in this report. The study found that while some testing at power is essential to verify equipment and system operability, safety can be improved, equipment degradation decreased, and unnecessary personnel burden relaxed by reducing the amount of testing at power

Book Review: New Perspectives on Technical Editing

Science.gov (United States)

Murphy, A. J. (Ed.); Sterken, Christiaan

2012-08-01

New Perspectives on Technical Editing by Avon J. Murphy (ed.) ISBN : 978-0895033949 (2010) Baywood Publishing Company Inc, Hardcover, 210 pages, 35.5 GBP This book presents a collection of 10 chapters dealing with diverse aspects of technical editing (ie, editorial planning, and analysis and structural changes made to other people's technological documents): research in technical editing, trends and teaching of technical editing, copyediting, and technical journal editing. The role and function of the modern journal and book editor is also dealt with in detail. Each chapter is written by an expert in the field: senior editors, university professors in technical communication, technical writers and linguists. The ever-evolving role of the editor is clearly elucidated in several historical reviews, and in the descriptions of the expectations for the future. A very striking aspect of this book is its extensive collection of bibliographic resources: every chapter lists dozens of very useful references, and the closing chapter, and annotated bibliography, contain many not so well known references, and are most useful. All in all, the book is a treasure trove listing more than 400 references, in addition to numerous webpage URLs embedded in the texts. The book is designed to help the reader to understand current practices and norms in technical editing, and to help to take action in editing as well as in teaching and educating would-be editors. The audience for this book thus includes editors and teachers, but also writers, researchers and students. A deep reading of this book will result in a better understanding of the difference between full technical editing and its much narrower component so well known as copyediting, and will convince any prospective editor that editing should not be undertaken if the people involved do not master the art of precision and accuracy in technical (as well as in human) communication, do not possess the technical know how and computer

48 CFR 2052.211-71 - Technical progress report.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Technical progress report... Technical progress report. As prescribed at 2011.104-70(b), the contracting officer shall insert the... solicitation. Technical Progress Report (JAN 1993) The contractor shall provide a monthly Technical Progress...

48 CFR 235.010 - Scientific and technical reports.

Science.gov (United States)

2010-10-01

....010 Scientific and technical reports. (b) For DoD, the Defense Technical Information Center is responsible for collecting all scientific and technical reports. For access to these reports, follow the... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Scientific and technical...

Technical Education and Economic Growth

Indian Academy of Sciences (India)

First page Back Continue Last page Graphics. Technical Education and Economic Growth. Technical Education and Economic Growth. Review of the Present Status. Expanding no.s and impairment of quality; Faculty shortage; Grim situation at Masters and PhD levels; Regional imbalance; Absence of International flavour ...

PIAAC Technical Standards and Guidelines

Science.gov (United States)

OECD Publishing, 2014

2014-01-01

The Programme for International Assessment of Adult Competencies (PIAAC) will establish technical standards and guidelines to ensure that the survey design and implementation processes of PIAAC yield high-quality and internationally comparable data. This document provides a revised version of the technical standards and guidelines originally…

Evaluation of a contact device type ejector system for liquid-liquid extraction

International Nuclear Information System (INIS)

Schwamback, Niomedes

2002-04-01

The objective of the present work was to evaluate an ejector system, operated simultaneously with two immiscible liquid phases and a gas phase, as a contact device for liquid-liquid extraction processes. The ejector, made of perspex, has a variable geometry, although this feature was not explored in the thesis. Motivated by recent uses of liquid-liquid extraction processes for the removal of traces of heavy metal from waste waters, it was decided to carry out tests with synthetic effluents. This strategy, typical of experimental work under evaluation of technical feasibility, greatly simplifies experiments, since the nature of the chemical species involved and their feed concentrations are known exactly and do not fluctuate. The extractant used was DEHPA (diethyl hexyl phosphoric acid). The metal chosen for tests was iron with oxidation number +3, because of its high extraction coefficient towards DEHPA and also for its chemical behavior similar to americium and other heavy metals. In addition to that, iron forms soluble coloured complexes adequate to spectrophotometric determination analysis, a simple, quick and very reliable analytical technique. The effects of electrolytes of interest, namely NaCl, FeSO 4 and Al(NO 3 ) 3 , upon the extraction process were investigated. The effects resulting from the introduction of a gas phase, actually air (bubbles), in the ejector upon the extraction efficiency were studied. By coupling advanced digital photographic technique and image analysis with microcomputer, the bubble mean size was measured. It was then correlated with equipment's geometrical (characteristic diameters) and operational variables (phases' flow rates and gas hold-ups). To enable scale-up procedures, data were preferably correlated by means of dimensionless groups. For the systems and conditions investigated in this thesis and under the same operational conditions, the introduction of air bubbles by means of an ejector has greatly improved the process

Technical training - Places available

CERN Document Server

2012-01-01

If you would like more information on a course, or for any other inquiry/suggestions, please contact Technical.Training@cern.ch Valeria Perez Reale, Learning Specialist, Technical Programme Coordinator (Tel.: 62424) Eva Stern and Elise Romero, Technical Training Administration (Tel.: 74924)   Electronics design Next Session Duration Language Availability Certified LabVIEW Associate Developer (CLAD) 06-Dec-12 to 06-Dec-12 1 hour English One more place available Compatibilité électromagnetique (CEM): Applications 23-Nov-12 to 23-Nov-12 3.5 hours English 3 places available Compatibilité électromagnétique (CEM): Introduction 23-Nov-12 to 23-Nov-12 3 hours English 43 places available Effets des Radiations sur les composants et systèmes électroniques 11-Dec-12 to 12-Dec-12 1 day 4 hours French 9 places available LabVIEW for beginners ...

Fuel Element Technical Manual

Energy Technology Data Exchange (ETDEWEB)

Burley, H.H. [ed.

1956-08-01

It is the purpose of the Fuel Element Technical Manual to Provide a single document describing the fabrication processes used in the manufacture of the fuel element as well as the technical bases for these processes. The manual will be instrumental in the indoctrination of personnel new to the field and will provide a single data reference for all personnel involved in the design or manufacture of the fuel element. The material contained in this manual was assembled by members of the Engineering Department and the Manufacturing Department at the Hanford Atomic Products Operation between the dates October, 1955 and June, 1956. Arrangement of the manual. The manual is divided into six parts: Part I--introduction; Part II--technical bases; Part III--process; Part IV--plant and equipment; Part V--process control and improvement; and VI--safety.

Quality Parameters of Curcuma Longa L. Extracts by Supercritical Fluid Extraction (SFE) and Ultrasonic Assisted Extraction (UAE)

International Nuclear Information System (INIS)

Zaibunnisa Abdul Haiyee; Siti Hafsah Mohd Shah; Khudzir Ismail; Nooraain Hashim; Wan Iryani Wan Ismail

2016-01-01

Turmeric is one of the prominently use herbal plants due to its diverse beneficial effects especially in Indian medicine. The rhizome part of the turmeric contains valuable compounds which have been said to owe its antimicrobial effects, anti-cancer, anti-inflammatory and enhance wound healing. Due to its short-life span and perishable properties, the conversion of the rhizome into turmeric extract is desirable. Several methods have been used for extraction such as Soxhlet extraction and pressurized liquid extraction (PLE). However, these techniques are tedious, laborious, time consuming and involves the usage of toxic organic solvent, of which safeness of the end product is doubtful. In this study, a rapid, reliable and green extraction method of supercritical fluid extraction (SFE) and ultrasonic assisted extraction (UAE) were used. SFE without modifier has resulted in 0.0006 mg/ 100 g of curcuminoids concentration and 5.62 % of yield (dry weight basis). UAE using ethanol was able to produce significantly the highest yield (6.40 %, dry weight basis) and the highest curcuminoids concentration (0.1020 mg/ 100 g). However, SFE was able to produce extract that contain significantly higher major volatile compounds; tumerone, ar-turmerone and curlone. Therefore, this study proves that both extraction methods were able to produce high quality turmeric extract. (author)

Getting Personal: Individuality, Innovation, and Technical Communication.

Science.gov (United States)

Steiner, Carol J.

1999-01-01

Suggests that effective communication between technical and nontechnical people is difficult because technical communication lacks a personal dimension: technical people give up their identity to be considered competent. Argues that a different approach to communication education for scientists, engineers, and technologists is required to equip…

Low functional programming of renal AT2R mediates the developmental origin of glomerulosclerosis in adult offspring induced by prenatal caffeine exposure

International Nuclear Information System (INIS)

Ao, Ying; Sun, Zhaoxia; Hu, Shuangshuang; Zuo, Na; Li, Bin; Yang, Shuailong; Xia, Liping; Wu, Yong; Wang, Linlong; He, Zheng; Wang, Hui

2015-01-01

Our previous study has indicated that prenatal caffeine exposure (PCE) could induce intrauterine growth retardation (IUGR) of offspring. Recent research suggested that IUGR is a risk factor for glomerulosclerosis. However, whether PCE could induce glomerulosclerosis and its underlying mechanisms remain unknown. This study aimed to demonstrate the induction to glomerulosclerosis in adult offspring by PCE and its intrauterine programming mechanisms. A rat model of IUGR was established by PCE, male fetuses and adult offspring at the age of postnatal week 24 were euthanized. The results revealed that the adult offspring kidneys in the PCE group exhibited glomerulosclerosis as well as interstitial fibrosis, accompanied by elevated levels of serum creatinine and urine protein. Renal angiotensin II receptor type 2 (AT 2 R) gene expression in adult offspring was reduced by PCE, whereas the renal angiotensin II receptor type 1a (AT 1a R)/AT 2 R expression ratio was increased. The fetal kidneys in the PCE group displayed an enlarged Bowman's space and a shrunken glomerular tuft, accompanied by a reduced cortex width and an increase in the nephrogenic zone/cortical zone ratio. Observation by electronic microscope revealed structural damage of podocytes; the reduced expression level of podocyte marker genes, nephrin and podocin, was also detected by q-PCR. Moreover, AT 2 R gene and protein expressions in fetal kidneys were inhibited by PCE, associated with the repression of the gene expression of glial-cell-line-derived neurotrophic factor (GDNF)/tyrosine kinase receptor (c-Ret) signaling pathway. These results demonstrated that PCE could induce dysplasia of fetal kidneys as well as glomerulosclerosis of adult offspring, and the low functional programming of renal AT 2 R might mediate the developmental origin of adult glomerulosclerosis. - Highlights: • Prenatal caffeine exposure induces glomerulosclerosis in adult offspring. • Prenatal caffeine exposure inhibits

Low functional programming of renal AT{sub 2}R mediates the developmental origin of glomerulosclerosis in adult offspring induced by prenatal caffeine exposure

Energy Technology Data Exchange (ETDEWEB)

Ao, Ying [Department of Pharmacology, School of Basic Medical Science of Wuhan University, Wuhan 430071 (China); Hubei Provincial Key Laboratory of Developmentally Originated Disorder, Wuhan 430071 (China); Sun, Zhaoxia; Hu, Shuangshuang; Zuo, Na [Department of Pharmacology, School of Basic Medical Science of Wuhan University, Wuhan 430071 (China); Li, Bin [Department of Orthopedic Surgery, Zhongnan Hospital of Wuhan University, Wuhan 430071 (China); Yang, Shuailong; Xia, Liping; Wu, Yong [Department of Pharmacology, School of Basic Medical Science of Wuhan University, Wuhan 430071 (China); Wang, Linlong [Department of Orthopedic Surgery, Zhongnan Hospital of Wuhan University, Wuhan 430071 (China); He, Zheng [Department of Pharmacology, School of Basic Medical Science of Wuhan University, Wuhan 430071 (China); Wang, Hui, E-mail: wanghui19@whu.edu.cn [Department of Pharmacology, School of Basic Medical Science of Wuhan University, Wuhan 430071 (China); Hubei Provincial Key Laboratory of Developmentally Originated Disorder, Wuhan 430071 (China)

2015-09-01

Our previous study has indicated that prenatal caffeine exposure (PCE) could induce intrauterine growth retardation (IUGR) of offspring. Recent research suggested that IUGR is a risk factor for glomerulosclerosis. However, whether PCE could induce glomerulosclerosis and its underlying mechanisms remain unknown. This study aimed to demonstrate the induction to glomerulosclerosis in adult offspring by PCE and its intrauterine programming mechanisms. A rat model of IUGR was established by PCE, male fetuses and adult offspring at the age of postnatal week 24 were euthanized. The results revealed that the adult offspring kidneys in the PCE group exhibited glomerulosclerosis as well as interstitial fibrosis, accompanied by elevated levels of serum creatinine and urine protein. Renal angiotensin II receptor type 2 (AT{sub 2}R) gene expression in adult offspring was reduced by PCE, whereas the renal angiotensin II receptor type 1a (AT{sub 1a}R)/AT{sub 2}R expression ratio was increased. The fetal kidneys in the PCE group displayed an enlarged Bowman's space and a shrunken glomerular tuft, accompanied by a reduced cortex width and an increase in the nephrogenic zone/cortical zone ratio. Observation by electronic microscope revealed structural damage of podocytes; the reduced expression level of podocyte marker genes, nephrin and podocin, was also detected by q-PCR. Moreover, AT{sub 2}R gene and protein expressions in fetal kidneys were inhibited by PCE, associated with the repression of the gene expression of glial-cell-line-derived neurotrophic factor (GDNF)/tyrosine kinase receptor (c-Ret) signaling pathway. These results demonstrated that PCE could induce dysplasia of fetal kidneys as well as glomerulosclerosis of adult offspring, and the low functional programming of renal AT{sub 2}R might mediate the developmental origin of adult glomerulosclerosis. - Highlights: • Prenatal caffeine exposure induces glomerulosclerosis in adult offspring. • Prenatal caffeine

Phytoforensics: Trees as bioindicators of potential indoor exposure via vapor intrusion.

Directory of Open Access Journals (Sweden)

Jordan L Wilson

Full Text Available Human exposure to volatile organic compounds (VOCs via vapor intrusion (VI is an emerging public health concern with notable detrimental impacts on public health. Phytoforensics, plant sampling to semi-quantitatively delineate subsurface contamination, provides a potential non-invasive screening approach to detect VI potential, and plant sampling is effective and also time- and cost-efficient. Existing VI assessment methods are time- and resource-intensive, invasive, and require access into residential and commercial buildings to drill holes through basement slabs to install sampling ports or require substantial equipment to install groundwater or soil vapor sampling outside the home. Tree-core samples collected in 2 days at the PCE Southeast Contamination Site in York, Nebraska were analyzed for tetrachloroethene (PCE and results demonstrated positive correlations with groundwater, soil, soil-gas, sub-slab, and indoor-air samples collected over a 2-year period. Because tree-core samples were not collocated with other samples, interpolated surfaces of PCE concentrations were estimated so that comparisons could be made between pairs of data. Results indicate moderate to high correlation with average indoor-air and sub-slab PCE concentrations over long periods of time (months to years to an interpolated tree-core PCE concentration surface, with Spearman's correlation coefficients (ρ ranging from 0.31 to 0.53 that are comparable to the pairwise correlation between sub-slab and indoor-air PCE concentrations (ρ = 0.55, n = 89. Strong correlations between soil-gas, sub-slab, and indoor-air PCE concentrations and an interpolated tree-core PCE concentration surface indicate that trees are valid indicators of potential VI and human exposure to subsurface environment pollutants. The rapid and non-invasive nature of tree sampling are notable advantages: even with less than 60 trees in the vicinity of the source area, roughly 12 hours of tree

Phytoforensics: Trees as bioindicators of potential indoor exposure via vapor intrusion.

Science.gov (United States)

Wilson, Jordan L; Samaranayake, V A; Limmer, Matt A; Burken, Joel G

2018-01-01

Human exposure to volatile organic compounds (VOCs) via vapor intrusion (VI) is an emerging public health concern with notable detrimental impacts on public health. Phytoforensics, plant sampling to semi-quantitatively delineate subsurface contamination, provides a potential non-invasive screening approach to detect VI potential, and plant sampling is effective and also time- and cost-efficient. Existing VI assessment methods are time- and resource-intensive, invasive, and require access into residential and commercial buildings to drill holes through basement slabs to install sampling ports or require substantial equipment to install groundwater or soil vapor sampling outside the home. Tree-core samples collected in 2 days at the PCE Southeast Contamination Site in York, Nebraska were analyzed for tetrachloroethene (PCE) and results demonstrated positive correlations with groundwater, soil, soil-gas, sub-slab, and indoor-air samples collected over a 2-year period. Because tree-core samples were not collocated with other samples, interpolated surfaces of PCE concentrations were estimated so that comparisons could be made between pairs of data. Results indicate moderate to high correlation with average indoor-air and sub-slab PCE concentrations over long periods of time (months to years) to an interpolated tree-core PCE concentration surface, with Spearman's correlation coefficients (ρ) ranging from 0.31 to 0.53 that are comparable to the pairwise correlation between sub-slab and indoor-air PCE concentrations (ρ = 0.55, n = 89). Strong correlations between soil-gas, sub-slab, and indoor-air PCE concentrations and an interpolated tree-core PCE concentration surface indicate that trees are valid indicators of potential VI and human exposure to subsurface environment pollutants. The rapid and non-invasive nature of tree sampling are notable advantages: even with less than 60 trees in the vicinity of the source area, roughly 12 hours of tree-core sampling with minimal

Phytoforensics: Trees as bioindicators of potential indoor exposure via vapor intrusion

Science.gov (United States)

Wilson, Jordan L.; Samaranayake, V.A.; Limmer, Matthew A.; Burken, Joel G.

2018-01-01

Human exposure to volatile organic compounds (VOCs) via vapor intrusion (VI) is an emerging public health concern with notable detrimental impacts on public health. Phytoforensics, plant sampling to semi-quantitatively delineate subsurface contamination, provides a potential non-invasive screening approach to detect VI potential, and plant sampling is effective and also time- and cost-efficient. Existing VI assessment methods are time- and resource-intensive, invasive, and require access into residential and commercial buildings to drill holes through basement slabs to install sampling ports or require substantial equipment to install groundwater or soil vapor sampling outside the home. Tree-core samples collected in 2 days at the PCE Southeast Contamination Site in York, Nebraska were analyzed for tetrachloroethene (PCE) and results demonstrated positive correlations with groundwater, soil, soil-gas, sub-slab, and indoor-air samples collected over a 2-year period. Because tree-core samples were not collocated with other samples, interpolated surfaces of PCE concentrations were estimated so that comparisons could be made between pairs of data. Results indicate moderate to high correlation with average indoor-air and sub-slab PCE concentrations over long periods of time (months to years) to an interpolated tree-core PCE concentration surface, with Spearman’s correlation coefficients (ρ) ranging from 0.31 to 0.53 that are comparable to the pairwise correlation between sub-slab and indoor-air PCE concentrations (ρ = 0.55, n = 89). Strong correlations between soil-gas, sub-slab, and indoor-air PCE concentrations and an interpolated tree-core PCE concentration surface indicate that trees are valid indicators of potential VI and human exposure to subsurface environment pollutants. The rapid and non-invasive nature of tree sampling are notable advantages: even with less than 60 trees in the vicinity of the source area, roughly 12 hours of tree-core sampling with

78 FR 29239 - Final Priority; Technical Assistance To Improve State Data Capacity-National Technical Assistance...

Science.gov (United States)

2013-05-20

... Assistance To Improve State Data Capacity--National Technical Assistance Center To Improve State Capacity To... Education and Rehabilitative Services announces a priority under the Technical Assistance to Improve State... (FY) 2013 and later years. We take this action to focus attention on an identified national need to...

Why and How to Advance Technical Copywriting.

Science.gov (United States)

Henson, Leigh

1996-01-01

States that promotional writing for industrial/high-tech products, or technical copywriting, is gaining more attention in technical communication, although it is neglected in higher education. Testifies to the significance of technical copywriting. Suggests that dialogical audience analysis and an emphasis on rational appeal will contribute to…

7 CFR 652.4 - Technical service standards.

Science.gov (United States)

2010-01-01

... technologies and practices. (c) A technical service provider must assume responsibility in writing for the... 7 Agriculture 6 2010-01-01 2010-01-01 false Technical service standards. 652.4 Section 652.4..., DEPARTMENT OF AGRICULTURE SUPPORT ACTIVITIES TECHNICAL SERVICE PROVIDER ASSISTANCE General Provisions § 652.4...

Technical approach document

International Nuclear Information System (INIS)

1989-12-01

The Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law 95-604 (PL95-604), grants the Secretary of Energy the authority and responsibility to perform such actions as are necessary to minimize radiation health hazards and other environmental hazards caused by inactive uranium mill sites. This Technical Approach Document (TAD) describes the general technical approaches and design criteria adopted by the US Department of Energy (DOE) in order to implement remedial action plans (RAPS) and final designs that comply with EPA standards. It does not address the technical approaches necessary for aquifer restoration at processing sites; a guidance document, currently in preparation, will describe aquifer restoration concerns and technical protocols. This document is a second revision to the original document issued in May 1986; the revision has been made in response to changes to the groundwater standards of 40 CFR 192, Subparts A--C, proposed by EPA as draft standards. New sections were added to define the design approaches and designs necessary to comply with the groundwater standards. These new sections are in addition to changes made throughout the document to reflect current procedures, especially in cover design, water resources protection, and alternate site selection; only minor revisions were made to some of the sections. Sections 3.0 is a new section defining the approach taken in the design of disposal cells; Section 4.0 has been revised to include design of vegetated covers; Section 8.0 discusses design approaches necessary for compliance with the groundwater standards; and Section 9.0 is a new section dealing with nonradiological hazardous constituents. 203 refs., 18 figs., 26 tabs

A process of spent nuclear fuel treatment with the interim storage of TRU by use amidic extractants

International Nuclear Information System (INIS)

Tachimori, Shoichi; Suzuki, Shinichi; Sasaki, Yuji

2001-01-01

A new chemical process, ARTIST process, is proposed for the treatment of spent nuclear fuel. The main concept of the ARTIST process is to recover and stock separately all actinides, uranium and a mixture of transuranics, and to dispose fission products. The process composed of two main steps, a uranium exclusive isolation and a total recovery of transuranium elements (TRU); which copes with the nuclear non-proliferation measures, and additional processes. Both actinide products are solidified by calcination and allowed to the interim storage for future utilization. These separations are achieved by use of amidic extractants in accord with the CHON principle. The technical feasibility of the ARTIST process was explained by the experimental results of both the branched-alkyl monoamides in extracting uranium and suppressing the extraction of tetravalent actinides due to the steric effect and the diglycolic amide in thorough extraction of all TRU by tridentate coordination. When these TRU are requested to put into reactors, LWR or FBR, for power generation or the Accelerator-Driven System (ADS) for transmutation, lanthanides are to be removed from TRU by utilizing a soft nitrogen donor ligand. (author)

Paramedics' non-technical skills: a literature review.

Science.gov (United States)

Shields, Allan; Flin, Rhona

2013-05-01

Healthcare organisations have started to examine the impact that the human worker has on patient safety. Adopting the Crew Resource Management (CRM) approach, used in aviation, the CRM or non-technical skills of anaesthetists, surgeons, scrub practitioners and emergency physicians have recently been identified to assist in their training and assessment. Paramedics are exposed to dynamic and dangerous situations where patients have to be managed, often with life-threatening injuries or illness. As in other safety-critical domains, the technical skills of paramedics are complemented by effective non-technical skills. The aim of this paper was to review the literature on the non-technical (social and cognitive) skills used by paramedics. This review was undertaken as part of a task analysis to identify the non-technical skills used by paramedics. Of the seven papers reviewed, the results have shown very little research on this topic and so reveal a gap in the understanding of paramedic non-technical skills.

Mechanomyographic Parameter Extraction Methods: An Appraisal for Clinical Applications

Directory of Open Access Journals (Sweden)

Morufu Olusola Ibitoye

2014-12-01

Full Text Available The research conducted in the last three decades has collectively demonstrated that the skeletal muscle performance can be alternatively assessed by mechanomyographic signal (MMG parameters. Indices of muscle performance, not limited to force, power, work, endurance and the related physiological processes underlying muscle activities during contraction have been evaluated in the light of the signal features. As a non-stationary signal that reflects several distinctive patterns of muscle actions, the illustrations obtained from the literature support the reliability of MMG in the analysis of muscles under voluntary and stimulus evoked contractions. An appraisal of the standard practice including the measurement theories of the methods used to extract parameters of the signal is vital to the application of the signal during experimental and clinical practices, especially in areas where electromyograms are contraindicated or have limited application. As we highlight the underpinning technical guidelines and domains where each method is well-suited, the limitations of the methods are also presented to position the state of the art in MMG parameters extraction, thus providing the theoretical framework for improvement on the current practices to widen the opportunity for new insights and discoveries. Since the signal modality has not been widely deployed due partly to the limited information extractable from the signals when compared with other classical techniques used to assess muscle performance, this survey is particularly relevant to the projected future of MMG applications in the realm of musculoskeletal assessments and in the real time detection of muscle activity.

Macroalgae-Derived Biofuel: A Review of Methods of Energy Extraction from Seaweed Biomass

Directory of Open Access Journals (Sweden)

John J. Milledge

2014-11-01

Full Text Available The potential of algal biomass as a source of liquid and gaseous biofuels is a highly topical theme, but as yet there is no successful economically viable commercial system producing biofuel. However, the majority of the research has focused on producing fuels from microalgae rather than from macroalgae. This article briefly reviews the methods by which useful energy may be extracted from macroalgae biomass including: direct combustion, pyrolysis, gasification, trans-esterification to biodiesel, hydrothermal liquefaction, fermentation to bioethanol, fermentation to biobutanol and anaerobic digestion, and explores technical and engineering difficulties that remain to be resolved.

48 CFR 952.242-70 - Technical direction.

Science.gov (United States)

2010-10-01

... contract. (d) All technical direction shall be issued in writing by the COR. (e) The Contractor must... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Technical direction. 952... FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Text of Provisions and Clauses 952.242-70 Technical...

48 CFR 1552.237-71 - Technical direction.

Science.gov (United States)

2010-10-01

.... (d) Technical direction will be issued in writing or confirmed in writing within five (5) days after... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Technical direction. 1552... Technical direction. As prescribed in 1537.110, insert a clause substantially the same as the following...

48 CFR 1852.242-70 - Technical direction.

Science.gov (United States)

2010-10-01

... Direction (SEP 1993) (a) Performance of the work under this contract is subject to the written technical... the Contracting Officer in writing in accordance with NASA FAR Supplement 1842.270. “Technical... in writing by the COTR. (d) The Contractor shall proceed promptly with the performance of technical...

48 CFR 227.7102-2 - Rights in technical data.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Rights in technical data... Technical Data 227.7102-2 Rights in technical data. (a) The clause at 252.227-7015, Technical Data—Commercial Items, provides the Government specific license rights in technical data pertaining to commercial...

Heterogeneity and contaminant transport modeling for the Savannah River integrated demonstration site

International Nuclear Information System (INIS)

Chesnut, D.A.

1992-11-01

The effectiveness of remediating aquifers and vadose zone sediments is frequently controlled by spatial heterogeneities. A continuing and long-recognized problem in selecting, planning, implementing, and operating remediation projects is the development of methods for quantitatively describing heterogeneity and predicting its effects on process performance. The similarity to and differences from modeling oil recovery processes in the petroleum industry are illustrated by the extension to contaminant extraction processes of an analytic model originally developed for waterflooding petroleum reservoirs. The resulting equations incorporate the effects of heterogeneity through a single parameter, σ. Fitting this model to the Savannah River in situ Air Stripping test data suggests that the injection of air into a horizontal well below the water table may have improved performance by changing the flow pattern in the vadose zone. This change increased the capture volume, and consequently the contaminant mass inventory, of the horizontal injection well completed in the vadose zone. The apparent increases (compared to extraction only from the horizontal well) are from 10,200 to 21,000 pounds for TCE and from 3,600 pounds to 59,800 pounds for PCE. The predominance of PCE in this calculated increase suggests that redistribution of flow paths in the vadose zone, rather than in-situ stripping, may provide most of the improvement. Although this preliminary conclusion remains to be reinforced by more sophisticated modeling currently in progress, there appears to be a definite improvement, which is attributable to air injection, over conventional remediation methods

Cognitive training for technical and non-technical skills in robotic surgery: a randomised controlled trial.

Science.gov (United States)

Raison, Nicholas; Ahmed, Kamran; Abe, Takashige; Brunckhorst, Oliver; Novara, Giacomo; Buffi, Nicolò; McIlhenny, Craig; van der Poel, Henk; van Hemelrijck, Mieke; Gavazzi, Andrea; Dasgupta, Prokar

2018-05-07

To investigate the effectiveness of motor imagery (MI) for technical skill and non-technical skill (NTS) training in minimally invasive surgery (MIS). A single-blind, parallel-group randomised controlled trial was conducted at the Vattikuti Institute of Robotic Surgery, King's College London. Novice surgeons were recruited by open invitation in 2015. After basic robotic skills training, participants underwent simple randomisation to either MI training or standard training. All participants completed a robotic urethrovesical anastomosis task within a simulated operating room. In addition to the technical task, participants were required to manage three scripted NTS scenarios. Assessment was performed by five blinded expert surgeons and a NTS expert using validated tools for evaluating technical skills [Global Evaluative Assessment of Robotic Skills (GEARS)] and NTS [Non-Technical Skills for Surgeons (NOTSS)]. Quality of MI was assessed using a revised Movement Imagery Questionnaire (MIQ). In all, 33 participants underwent MI training and 29 underwent standard training. Interrater reliability was high, Krippendorff's α = 0.85. After MI training, the mean (sd) GEARS score was significantly higher than after standard training, at 13.1 (3.25) vs 11.4 (2.97) (P = 0.03). There was no difference in mean NOTSS scores, at 25.8 vs 26.4 (P = 0.77). MI training was successful with significantly higher imagery scores than standard training (mean MIQ score 5.1 vs 4.5, P = 0.04). Motor imagery is an effective training tool for improving technical skill in MIS even in novice participants. No beneficial effect for NTS was found. © 2018 The Authors BJU International © 2018 BJU International Published by John Wiley & Sons Ltd.