WorldWideScience

Sample records for passenger vehicle development

  1. Near term hybrid passenger vehicle development program, phase 1

    Science.gov (United States)

    1980-01-01

    Missions for hybrid vehicles that promise to yield high petroleum impact were identified and a preliminary design, was developed that satisfies the mission requirements and performance specifications. Technologies that are critical to successful vehicle design, development and fabrication were determined. Trade-off studies to maximize fuel savings were used to develop initial design specifications of the near term hybrid vehicle. Various designs were "driven" through detailed computer simulations which calculate the petroleum consumption in standard driving cycles, the petroleum and electricity consumptions over the specified missions, and the vehicle's life cycle costs over a 10 year vehicle lifetime. Particular attention was given to the selection of the electric motor, heat engine, drivetrain, battery pack and control system. The preliminary design reflects a modified current compact car powered by a currently available turbocharged diesel engine and a 24 kW (peak) compound dc electric motor.

  2. Phase I of the Near-Term Hybrid Passenger-Vehicle Development Program. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1980-10-01

    Under contract to the Jet Propulsion Laboratory of the California Institute of Technology, Minicars conducted Phase I of the Near-Term Hybrid Passenger Vehicle (NTHV) Development Program. This program led to the preliminary design of a hybrid (electric and internal combustion engine powered) vehicle and fulfilled the objectives set by JPL. JPL requested that the report address certain specific topics. A brief summary of all Phase I activities is given initially; the hybrid vehicle preliminary design is described in Sections 4, 5, and 6. Table 2 of the Summary lists performance projections for the overall vehicle and some of its subsystems. Section 4.5 gives references to the more-detailed design information found in the Preliminary Design Data Package (Appendix C). Alternative hybrid-vehicle design options are discussed in Sections 3 through 6. A listing of the tradeoff study alternatives is included in Section 3. Computer simulations are discussed in Section 9. Section 8 describes the supporting economic analyses. Reliability and safety considerations are discussed specifically in Section 7 and are mentioned in Sections 4, 5, and 6. Section 10 lists conclusions and recommendations arrived at during the performance of Phase I. A complete bibliography follows the list of references.

  3. Safety of railroad passenger vehicle dynamics : OMNISIM simulation and test correlations for passenger rail cars

    Science.gov (United States)

    2002-07-01

    The purpose of the work is to validate the safety assessment methodology previously developed for passenger rail vehicle dynamics, which requires the application of simulation tools as well as testing of vehicles under different track scenarios. This...

  4. 49 CFR 541.5 - Requirements for passenger motor vehicles.

    Science.gov (United States)

    2010-10-01

    ... TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR VEHICLE THEFT PREVENTION STANDARD § 541.5 Requirements for passenger motor vehicles. (a) Each passenger motor vehicle subject to... 49 Transportation 6 2010-10-01 2010-10-01 false Requirements for passenger motor vehicles. 541.5...

  5. Thermoelectric Waste Heat Recovery Program for Passenger Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Jovovic, Vladimir [Gentherm Incorporated, Azusa, CA (United States)

    2015-12-31

    Gentherm began work in October 2011 to develop a Thermoelectric Waste Energy Recovery System for passenger vehicle applications. Partners in this program were BMW and Tenneco. Tenneco, in the role of TIER 1 supplier, developed the system-level packaging of the thermoelectric power generator. As the OEM, BMW Group demonstrated the TEG system in their vehicle in the final program phase. Gentherm demonstrated the performance of the TEG in medium duty and heavy duty vehicles. Technology developed and demonstrated in this program showed potential to reduce fuel consumption in medium and heavy duty vehicles. In light duty vehicles it showed more modest potential.

  6. Advanced axial field D.C. motor development for electric passenger vehicle

    Science.gov (United States)

    Jones, W. J.

    1982-01-01

    A wound-field axial-flux dc motor was developed for an electric vehicle drive system. The motor is essentially an axial-flux version of the classical Gramme-ring winding motor, but the active conductors are recessed into slots cut into the two opposite faces of the laminated tape-wound core ring. Three motors were built and tested in the program. The second (functional) model was a six-pole machine which weighed 88.5 kg. It developed 16.9 km (33.0 hp), and a max speed of 4800 rpm. Full load efficiency was 92% and predicted SAE D-cycle efficiency was 88%. The last engineering) model was a 4-pole machine with compoles, allowing a weight reduction to 45 kg (100 lbs.) while addressing some manufacturability problems. The engineering model was rated at 13.2 kw (17.6 hp) at 3000 rpm, with a peak power of 19.8 km (26.4 hp) and a max speed of 7200 rpm. Initial test results on this motor showed poor commutation and efficiency; the program was terminated without resolution of these problems.

  7. Is passenger vehicle incompatibility still a problem?

    Science.gov (United States)

    Teoh, Eric R; Nolan, Joseph M

    2012-01-01

    Passenger cars often are at a disadvantage when colliding with light trucks (sport utility vehicles [SUVs] and pickups) due to differences in mass, vehicle structural alignment, and stiffness. In 2003, vehicle manufacturers agreed to voluntary measures to improve compatibility, especially in front-to-front and front-to-side crashes, with full adherence to be achieved by September 2009. This study examined whether fatality rates are consistent with the expected benefit of this agreement. Analyses examined 2 death rates for 1- to 4-year-old passenger vehicles during 2000-2001 and 2008-2009 in the United States: occupant deaths per million registered vehicle years in these vehicles and deaths in other cars that collided with these vehicles in 2-vehicle crashes per million registered vehicle years. These rates were computed for each study period and for cars/minivans (referred to as cars), SUVs, and pickups by curb weight (in 500-pound increments). The latter death rate, referred to as the car crash partner death rate, also was computed for front-to-front crashes and front-to-side crashes where the front of the 1- to 4-year-old vehicle struck the side of the partner car. In both study periods, occupant death rates generally decreased for each vehicle type both with increasing curb weight and over time. SUVs experienced the greatest declines compared with cars and pickups. This is due in part to the early fitment of electronic stability control in SUVs, which drastically reduced the incidence of single-vehicle rollover crashes. Pickups had the highest death rates in both study periods. Car crash partner death rates generally declined over time for all vehicle categories but more steeply for SUVs and pickups colliding with cars than for cars colliding with cars. In fact, the car crash partner death rates for SUVs and cars were nearly identical during 2008-2009, suggesting that the voluntary design changes for compatibility have been effective. Car crash partner death

  8. Near term hybrid passenger vehicle development program. Phase I. Appendices C and D. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-01

    The derivation of and actual preliminary design of the Near Term Hybrid Vehicle (NTHV) are presented. The NTHV uses a modified GM Citation body, a VW Rabbit turbocharged diesel engine, a 24KW compound dc electric motor, a modified GM automatic transmission, and an on-board computer for transmission control. The following NTHV information is presented: the results of the trade-off studies are summarized; the overall vehicle design; the selection of the design concept and the base vehicle (the Chevrolet Citation), the battery pack configuration, structural modifications, occupant protection, vehicle dynamics, and aerodynamics; the powertrain design, including the transmission, coupling devices, engine, motor, accessory drive, and powertrain integration; the motor controller; the battery type, duty cycle, charger, and thermal requirements; the control system (electronics); the identification of requirements, software algorithm requirements, processor selection and system design, sensor and actuator characteristics, displays, diagnostics, and other topics; environmental system including heating, air conditioning, and compressor drive; the specifications, weight breakdown, and energy consumption measures; advanced technology components, and the data sources and assumptions used. (LCL)

  9. Analysis of bus passenger comfort perception based on passenger load factor and in-vehicle time.

    Science.gov (United States)

    Shen, Xianghao; Feng, Shumin; Li, Zhenning; Hu, Baoyu

    2016-01-01

    Although bus comfort is a crucial indicator of service quality, existing studies tend to focus on passenger load and ignore in-vehicle time, which can also affect passengers' comfort perception. Therefore, by conducting surveys, this study examines passengers' comfort perception while accounting for both factors. Then, using the survey data, it performs a two-way analysis of variance and shows that both in-vehicle time and passenger load significantly affect passenger comfort. Then, a bus comfort model is proposed to evaluate comfort level, followed by a sensitivity analysis. The method introduced in this study has theoretical implications for bus operators attempting to improve bus service quality.

  10. Research on the recycling industry development model for typical exterior plastic components of end-of-life passenger vehicle based on the SWOT method.

    Science.gov (United States)

    Zhang, Hongshen; Chen, Ming

    2013-11-01

    In-depth studies on the recycling of typical automotive exterior plastic parts are significant and beneficial for environmental protection, energy conservation, and sustainable development of China. In the current study, several methods were used to analyze the recycling industry model for typical exterior parts of passenger vehicles in China. The strengths, weaknesses, opportunities, and challenges of the current recycling industry for typical exterior parts of passenger vehicles were analyzed comprehensively based on the SWOT method. The internal factor evaluation matrix and external factor evaluation matrix were used to evaluate the internal and external factors of the recycling industry. The recycling industry was found to respond well to all the factors and it was found to face good developing opportunities. Then, the cross-link strategies analysis for the typical exterior parts of the passenger car industry of China was conducted based on the SWOT analysis strategies and established SWOT matrix. Finally, based on the aforementioned research, the recycling industry model led by automobile manufacturers was promoted. Copyright © 2013 Elsevier Ltd. All rights reserved.

  11. Effects of vehicle power on passenger vehicle speeds.

    Science.gov (United States)

    McCartt, Anne T; Hu, Wen

    2017-07-04

    During the past 2 decades, there have been large increases in mean horsepower and the mean horsepower-to-vehicle weight ratio for all types of new passenger vehicles in the United States. This study examined the relationship between travel speeds and vehicle power, defined as horsepower per 100 pounds of vehicle weight. Speed cameras measured travel speeds and photographed license plates and drivers of passenger vehicles traveling on roadways in Northern Virginia during daytime off-peak hours in spring 2013. The driver licensing agencies in the District of Columbia, Maryland, and Virginia provided vehicle information numbers (VINs) by matching license plate numbers with vehicle registration records and provided the age, gender, and ZIP code of the registered owner(s). VINs were decoded to obtain the curb weight and horsepower of vehicles. The study focused on 26,659 observed vehicles for which information on horsepower was available and the observed age and gender of drivers matched vehicle registration records. Log-linear regression estimated the effects of vehicle power on mean travel speeds, and logistic regression estimated the effects of vehicle power on the likelihood of a vehicle traveling over the speed limit and more than 10 mph over the limit. After controlling for driver characteristics, speed limit, vehicle type, and traffic volume, a 1-unit increase in vehicle power was associated with a 0.7% increase in mean speed, a 2.7% increase in the likelihood of a vehicle exceeding the speed limit by any amount, and an 11.6% increase in the likelihood of a vehicle exceeding the limit by 10 mph. All of these increases were highly significant. Speeding persists as a major factor in crashes in the United States. There are indications that travel speeds have increased in recent years. The current findings suggest the trend toward substantially more powerful vehicles may be contributing to higher speeds. Given the strong association between travel speed and crash

  12. Development of power management concepts for the electrical power system in passenger vehicles; Entwicklung von Energiemanagement-Konzepten fuer das elektrische Bordnetz im Kraftfahrzeug

    Energy Technology Data Exchange (ETDEWEB)

    Meir, F.; Bertram, M.; Christ, T. [BMW Group (Germany); Reuss, H.-C. [Stuttgart Univ. (Germany). IVK; Morawietz, L.; Buechner, S. [Technische Univ. Dresden (Germany)

    2005-07-01

    The implementation of innovative systems in passenger vehicles requires a stable electric power supply. Moreover, the increasing demand on electric energy causes a larger influence on the fuel consumption. The task of an intelligent Power Management System is to optimise power generation as well as to achieve a reliable supply for electric loads. This paper deals with tools for development and evaluation of these functions. The preliminary design of control concepts is based on simulation. The simulation models are completely described by an object-oriented modeling language. Parameters of components from present power systems are extracted from measurements in the vehicle and with the help of a Hardware-in-the-Loop test bench. First simulation results indicate the quality of the new power management concepts. In parallel, these concepts can be approved on the test bench. (orig.)

  13. Towards Life Cycle Sustainability Assessment of Alternative Passenger Vehicles

    Directory of Open Access Journals (Sweden)

    Nuri Cihat Onat

    2014-12-01

    Full Text Available Sustainable transportation and mobility are key components and central to sustainable development. This research aims to reveal the macro-level social, economic, and environmental impacts of alternative vehicle technologies in the U.S. The studied vehicle technologies are conventional gasoline, hybrid, plug-in hybrid with four different all-electric ranges, and full battery electric vehicles (BEV. In total, 19 macro level sustainability indicators are quantified for a scenario in which electric vehicles are charged through the existing U.S. power grid with no additional infrastructure, and an extreme scenario in which electric vehicles are fully charged with solar charging stations. The analysis covers all life cycle phases from the material extraction, processing, manufacturing, and operation phases to the end-of-life phases of vehicles and batteries. Results of this analysis revealed that the manufacturing phase is the most influential phase in terms of socio-economic impacts compared to other life cycle phases, whereas operation phase is the most dominant phase in the terms of environmental impacts and some of the socio-economic impacts such as human health and economic cost of emissions. Electric vehicles have less air pollution cost and human health impacts compared to conventional gasoline vehicles. The economic cost of emissions and human health impact reduction potential can be up to 45% and 35%, respectively, if electric vehicles are charged through solar charging stations. Electric vehicles have potential to generate income for low and medium skilled workers in the U.S. In addition to quantified sustainability indicators, some sustainability metrics were developed to compare relative sustainability performance alternative passenger vehicles. BEV has the lowest greenhouse gas emissions and ecological land footprint per $ of its contribution to the U.S. GDP, and has the lowest ecological footprint per unit of its energy consumption. The

  14. Research on the compressive strength of a passenger vehicle roof

    Science.gov (United States)

    Zhao, Guanglei; Cao, Jianxiao; Liu, Tao; Yang, Na; Zhao, Hongguang

    2017-05-01

    To study the compressive strength of a passenger vehicle roof, this paper makes the simulation test on the static collapse of the passenger vehicle roof and analyzes the stress and deformation of the vehicle roof under pressure in accordance with the Roof Crush Resistance of Passenger Cars (GB26134-2010). It studies the optimization on the major stressed parts, pillar A, pillar B and the rail of roof, during the static collapse process of passenger vehicle roof. The result shows that the thickness of pillar A and the roof rail has significant influence on the compressive strength of the roof while that of pillar B has minor influence on the compressive strength of the roof.

  15. Natural gas passenger vehicles: challenges and way forward

    International Nuclear Information System (INIS)

    Sahari, B. B.; Hamouda, A. M. S.

    2006-01-01

    Natural gas vehicles have been used in the world for many years: at present, there are about 3 million vehicles running on natural gas and many governments and vehicle manufactures are involved in programs for further developing the market for natural gas vehicles. In comparison to other forms of energy for vehicles, natural gas (NG) engenders low pressures on the environment. At the same time, because of its technical characteristics, NG is very suitable for motor use. The economic advantage of converting a vehicles (NGVs) would be expected to attract the interest of a great number of people, and achieve rapid and widespread diffusion. On the contrary, traditional fuels still dominate the scene, and show no sign of going out of fashion. The use of natural gas as automotive fuel has become of national and worldwide interests particularly so with the recent increase in petrol price, depleting petrol reserves and stringent control of exhaust emission levels. For automotive applications, shifting from petrol to gas needs technological research and development. Within the framework of the reciprocating piston based engine this development is very challenging with technological issues of low range, refueling infrastructure, heavy fuel storage, safety, emissions control and gas operating pressures. Other issues include available expertise and experience in research management. This paper describes the advances being made with passenger vehicles natural gas engines worldwide and in Malaysia more specific. The significant milestones in the development of NGV in Malaysia and the rationale behind the choice of NGV industry including the NGV vehicle population growth, the development of service station as well as the expansion of the sales volume will be illustrated. The presentation presents also development stages and advances in development, fabrication and testing a Compressed Natural Gas Direct Injection vehicle and NGV refueling station. This presentation discuses the

  16. The Simultaneous Vehicle Scheduling and Passenger Service Problem

    DEFF Research Database (Denmark)

    Petersen, Hanne Løhmann; Larsen, Allan; Madsen, Oli B.G.

    modifications of the timetable during the vehicle scheduling phase. This planning approach is referred to as the Simultaneous Vehicle Scheduling and Passenger Service Problem (SVSPSP). The SVSPSP is solved using a large neighbourhood search metaheuristic. The proposed framework is tested on data inspired......Passengers using public transport systems often experience waiting times when transferring between two scheduled services. We propose a planning approach which seeks to obtain a favorable trade-off between the conflicting objectives passenger service and operating cost, by allowing some moderate...

  17. The Simultaneous Vehicle Scheduling and Passenger Service Problem

    DEFF Research Database (Denmark)

    Petersen, Hanne Løhmann; Larsen, Allan; Madsen, Oli B.G.

    2013-01-01

    , by modifying the timetable. The planning approach is referred to as the simultaneous vehicle scheduling and passenger service problem (SVSPSP). The SVSPSP is modelled as an integer programming problem and solved using a large neighborhood search metaheuristic. The proposed framework is tested on data inspired......Passengers using public transport systems often experience waiting times when transferring between two scheduled services. In this paper we propose a planning approach that seeks to obtain a favourable trade-off between the two contrasting objectives, passenger service and operating cost...

  18. 76 FR 5825 - U.S.-Korea Free Trade Agreement: Passenger Vehicle Sector Update

    Science.gov (United States)

    2011-02-02

    ...: Passenger Vehicle Sector Update AGENCY: United States International Trade Commission. ACTION: Institution of...) instituted investigation No. 332-523, U.S.-Korea Free Trade Agreement: Passenger Vehicle Sector Update. DATES... concluded negotiations to modify the FTA, including certain provisions relating to the passenger vehicle...

  19. 49 CFR 583.10 - Outside suppliers of passenger motor vehicle equipment.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 7 2010-10-01 2010-10-01 false Outside suppliers of passenger motor vehicle... CONTENT LABELING § 583.10 Outside suppliers of passenger motor vehicle equipment. (a) For each unique type of passenger motor vehicle equipment for which a manufacturer or allied supplier requests information...

  20. 36 CFR 13.1316 - Commercial transport of passengers by motor vehicles.

    Science.gov (United States)

    2010-07-01

    ... passengers by motor vehicles. 13.1316 Section 13.1316 Parks, Forests, and Public Property NATIONAL PARK... National Park General Provisions § 13.1316 Commercial transport of passengers by motor vehicles. Commercial transport of passengers by motor vehicles on Exit Glacier Road is allowed without a written permit. However...

  1. 49 CFR 583.11 - Allied suppliers of passenger motor vehicle equipment.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 7 2010-10-01 2010-10-01 false Allied suppliers of passenger motor vehicle... CONTENT LABELING § 583.11 Allied suppliers of passenger motor vehicle equipment. (a) For each unique type of passenger motor vehicle equipment which an allied supplier supplies to the manufacturer with which...

  2. Passenger vehicles that minimize the costs of ownership and environmental damages in the Indian market

    International Nuclear Information System (INIS)

    Gilmore, Elisabeth A.; Patwardhan, Anand

    2016-01-01

    Highlights: • Full costs (private and social) are evaluated for Indian passenger cars. • Diesel has low ownership costs, but higher climate and health damages. • Compressed natural gas cars have lower costs and damages than petrol cars. • Electric cars have higher damages due to electricity generation emissions. • CNG and less carbon intensive electricity minimizes Indian cars’ full cost. - Abstract: Rapid expansion of population and income growth in developing countries, such as India, is increasing the demand for many goods and services, including four-wheeled passenger cars. Passenger cars provide personal mobility; however, they also have negative implications for human wellbeing from increased air pollutants and greenhouse gases (GHG). Here, we evaluate the range of passenger vehicles available in the Indian market to identify options that minimize costs, human health effects and climate damages. Our approach is to compare alternative fuel/powertrain vehicles with similar conventional gasoline fueled vehicles and assess the differences in full (private and societal) costs for each pair. Private costs are the combination of capital costs and the discounted expected future fuel costs over the vehicle lifetime. The costs to human health from air quality are calculated using intake fractions to estimate exposure and literature values for the damage costs adjusted by benefits transfer methods. We use the Social Cost of Carbon to estimate climate damages. We find that, on average, the net present value (NPV) of the full costs of compressed natural gas (CNG) vehicles are lower than comparable gasoline vehicles, while, diesel vehicles have higher costs. Presently, electric vehicles have higher private costs (due to high capital costs) and societal costs (due to electricity generation emissions). Either a less carbon intensive electricity grid or an increase in the CNG fleet would minimize total costs, human health effects and GHG emissions from the

  3. Heat management in motor vehicles 3. Development methods and innovations in heat management in passenger cars and industrial vehicles; Waermemanagement des Kraftfahrzeugs 3. Entwicklungsmethoden und Innovationen der Kfz- und Nfz-Waermetechnik

    Energy Technology Data Exchange (ETDEWEB)

    Deussen, N. (ed.) [Fachhochschule Koeln (Germany). Labor fuer Verbrennungsmotoren und Applikation

    2002-07-01

    The proceedings volume outlines problem solutions, development strategies and design methods relating to heat management in motor vehicles. The focus is on utilisation, supply, transmission and release of heat in passenger cars and industrial vehicles. The complete state of the art is reviewed, with the focus on the following subjects: The potential of heat management in terms of performance and comfort; Future strategies for optimisation of thermal processes; Expert knowledge in component and system innovations; Status and perspectives of user software; Engine cooling, vehicle air conditioning, heat protection; Methodology; Numeric fluid mechanics; Heat transfer; Practical applications of thermal engineering, Heat management in engines; Thermal system optimisation; CFD; Future numeric methods in heat transfer and fluid mechanics; Methods of measurement and instrumentation. [German] Der Tagungsband informiert in einem aktuellen Ueberblick ueber Problemloesungen, Entwicklungsstrategien und Auslegungsmethoden im Umfeld des Kraftfahrzeug-Waermemanagements. Dabei wird insbesondere auf die Optimierung der Nutzung, Bereitstellung, Uebertragung und Abgabe von Waerme fokussiert. Der Inhalt umfasst dabei Anwendungen bei Automobilen und Nutzfahrzeugen. Der Leser erhaelt einen konkreten Ueberblick ueber die Trends auf neuestem Stand der Technik. Besondere Schwerpunkte sind: Potenzial des Waermemanagements bezueglich Leistung und Kundennutzen - Zukunftsweisende Strategien zur Optimierung waermetechnischer Prozesse - Kompaktes Fachwissen bei Bauteil- und System-Innovationen - Stand der Technik und Zukunftsperspektive bei Anwendersoftware. Inhalt: Motorkuehlung - Fahrzeugklimatisierung - Hitzeschutz - Methoden der Waermetechnik - Numerische Stroemungsmechanik - Waermeuebertragung - Anwendungsbeispiele der Waermetechnik - Motor-Thermomanagement - Waermetechnische Systemoptimierung - CFD - Zukuenftige numerische Methoden der Waermeuebertragung und Stroemungsmechanik - Messtechnik

  4. The importance of high vehicle power for passenger car emissions

    Science.gov (United States)

    Carslaw, David C.; Williams, Martin L.; Tate, James E.; Beevers, Sean D.

    2013-04-01

    In this paper we use a quantile regression technique to explore the emissions characteristics of petrol and diesel passenger cars to reveal the importance of high vehicle power on exhaust emissions. A large database of ≈67,000 passenger cars from vehicle emission remote sensing data was used from surveys from several campaigns around the UK. Most previous remote sensing studies have focused on presenting mean emission estimates by vehicle type over time. However, as shown in the current work, considerably more insight can be gained into vehicle emission characteristics if techniques are used that can describe and model the full distribution of vehicle emissions as a function of important explanatory variables. For post-2000 model year (Euro 3-5) diesel cars it is shown that there is a strong dependence of vehicle specific power for emissions of NOx that was absent in earlier models and is absent for other pollutants such as CO, hydrocarbons and 'smoke'. Furthermore, we also find a stronger dependence on vehicle specific power for older catalyst-equipped petrol vehicles (Euro 1/2) on emissions of NOx that is less important for other emissions such as CO and hydrocarbons. Moreover, it is shown that while the rated maximum power output of petrol cars has remained almost constant over the past 15-20 years, the power output from diesel cars has increased markedly by about 50%. These results suggest that changes to vehicle technology, driving conditions and driver behaviour have become more important determinants of passenger car NOx emissions in recent years and may help explain why urban ambient concentrations of NOx have not decreased as much as anticipated.

  5. Stress analysis on passenger deck due to modification from passenger ship to vehicle-carrying ship

    Science.gov (United States)

    Zubaydi, A.; Sujiatanti, S. H.; Hariyanto, T. R.

    2018-03-01

    Stress is a basic concept in learning about material mechanism. The main focus that needs to be brought to attention in analyzing stress is strength, which is the structural capacity to carry or distribute loads. The structural capacity not only measured by comparing the maximum stress with the material’s yield strength but also with the permissible stress required by the Indonesian Classification Bureau (BKI), which certainly makes it much safer. This final project analyzes stress in passenger deck that experiences modification due to load changes, from passenger load to vehicle one, carrying: 6-wheels truck with maximum weight of 14 tons, a passenger car with maximum weight of 3.5 tons, and a motorcycle with maximum weight of 0.4 tons. The deck structure is modelled using finite element software. The boundary conditions given to the structural model are fix and simple constraint. The load that works on this deck is the deck load which comes from the vehicles on deck with three vehicles’ arrangement plans. After that, software modelling is conducted for analysis purpose. Analysis result shows a variation of maximum stress that occurs i.e. 135 N/mm2, 133 N/mm2, and 152 N/mm2. Those maximum stresses will not affect the structure of passenger deck’s because the maximum stress that occurs indicates smaller value compared to the Indonesian Classification Bureau’s permissible stress (175 N/mm2) as well as the material’s yield strength (235 N/mm2). Thus, the structural strength of passenger deck is shown to be capable of carrying the weight of vehicles in accordance with the three vehicles’ arrangement plans.

  6. A lightweight electronically commutated dc motor for electric passenger vehicles

    Science.gov (United States)

    Echolds, E. F.; Walla, P. S.

    1982-01-01

    A functional model breadboard converter and a rare-earth-cobalt, permanent magnet motor; as well as an engineering model converter and PM motor suitable for vehicle installations were developed and tested. The converter and motor achieved an 88% peak efficiency, a maximum output of 26 kW at 26,000 rpm, and a continuous rating of 15 kW. The system also generated power to the source during braking, with a demonstrated peak power available at the converter terminals of approximately 26 kW at 88% efficiency. Major conclusions include: (1) the SAE J227a(D) driving cycle efficiency for the converter/motor is 86% to 88% when energy available for recovery at the converter terminals is included; (2) the converter initial cost is approximately five times that of the permanent magnet motor, but can be reduced by means of LSI logic and integrated liquid cooled semiconductor packages; and (3) an electronically commutated motor with a liquid cooled converter will operate reliably without service or maintenance for the life of a passenger vehicle.

  7. A lightweight electronically commutated dc motor for electric passenger vehicles

    Science.gov (United States)

    Echolds, E. F.; Walla, P. S.

    1982-09-01

    A functional model breadboard converter and a rare-earth-cobalt, permanent magnet motor; as well as an engineering model converter and PM motor suitable for vehicle installations were developed and tested. The converter and motor achieved an 88% peak efficiency, a maximum output of 26 kW at 26,000 rpm, and a continuous rating of 15 kW. The system also generated power to the source during braking, with a demonstrated peak power available at the converter terminals of approximately 26 kW at 88% efficiency. Major conclusions include: (1) the SAE J227a(D) driving cycle efficiency for the converter/motor is 86% to 88% when energy available for recovery at the converter terminals is included; (2) the converter initial cost is approximately five times that of the permanent magnet motor, but can be reduced by means of LSI logic and integrated liquid cooled semiconductor packages; and (3) an electronically commutated motor with a liquid cooled converter will operate reliably without service or maintenance for the life of a passenger vehicle.

  8. 36 CFR 1005.4 - Commercial passenger-carrying motor vehicles.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Commercial passenger-carrying motor vehicles. 1005.4 Section 1005.4 Parks, Forests, and Public Property PRESIDIO TRUST COMMERCIAL AND PRIVATE OPERATIONS § 1005.4 Commercial passenger-carrying motor vehicles. Passenger-carrying motor...

  9. Designing interior space for drivers of passenger vehicle

    Directory of Open Access Journals (Sweden)

    Spasojević-Brkić Vesna K.

    2014-01-01

    Full Text Available The current study is a review of our previous papers with certain improvements, so it proves the hypothesis that passenger vehicles are still not sufficiently adapted to man in terms of ergonomics, especially from the aspect of interior space. In the ergonomic adjustment of passenger vehicles, the limits of anthropomeasures and technical limitations, are the most important. The methodology mainly uses operative investigations, and the 'man-vehicle' system is optimized within existing limitations. Here, we also explain original methodology for modeling that space. The fact that there is a point '0' as the origin point of a coordinate system with x, y and z axes of the man-vehicle system, which can be considered to be more or less fixed, enabled us to determine more accurately the mechanical and mathematical codependence in this system. The paper also proves that the anthropomeasures of length have mechanical and mathematical functions which also determine the width, i.e. all three dimensions and provides the design of the space behind the windscreen glass, the position of the steering wheel and the position of the foot commands with space for feet and knees determined, as well as the total space which the driver occupies. It is proved that the floor-ceiling height of a vehicle is primarily affected by the anthropomeasures of seating height and lower leg, while width is affected by the anthropomeasures of lower and upper leg and only then by shoulder width, so that the interior space for the driver of a passenger vehicle is 1250 mm and the width for knees spread at seat level is 926 mm maximum.

  10. Baseline tests of the C. H. Waterman DAF electric passenger vehicle

    Science.gov (United States)

    Sargent, N. B.; Maslowski, E. A.; Soltis, R. F.; Schuh, R. M.

    1977-01-01

    An electric vehicle was tested as part of an Energy Research Development Administration (ERDA) project to characterize the state-of-the-art of electric vehicles. The Waterman vehicle performance test results are presented in this report. The vehicle is a converted four-passenger DAF 46 sedan. It is powered by sixteen 6-volt traction batteries through a three-step contactor controller actuated by a foot throttle to change the voltage applied to the 6.7 kW motor. The braking system is a conventional hydraulic braking system.

  11. Child passengers injured in motor vehicle crashes.

    Science.gov (United States)

    Romano, Eduardo; Kelley-Baker, Tara

    2015-02-01

    During 2010, 171,000 children aged 0-14 were injured in motor vehicle crashes. Despite the severity of the problem, research has been limited, and most of what we know about these children emanates from fatal crash databases. Using information from the General Estimates System, this effort examines the occurrence of non-fatal crashes among children aged 0-14 over the last decade. We found that about 1% of the non-injured children in the file had been driven by a driver who was positive for alcohol. This percentage climbed to about 2% among children who had suffered injuries. Compared with the proportion of alcohol-positive drivers at the time of the crash, the proportion of drivers who sped or failed to obey a traffic signal was significantly higher. The finding that drinking and driving with children did not decrease over time questions the adequacy of the extant child endangerment laws. Copyright © 2014 National Safety Council and Elsevier Ltd. All rights reserved.

  12. Modeling Hydrogen Refueling Infrastructure to Support Passenger Vehicles

    Directory of Open Access Journals (Sweden)

    Matteo Muratori

    2018-05-01

    Full Text Available The year 2014 marked hydrogen fuel cell electric vehicles (FCEVs first becoming commercially available in California, where significant investments are being made to promote the adoption of alternative transportation fuels. A refueling infrastructure network that guarantees adequate coverage and expands in line with vehicle sales is required for FCEVs to be successfully adopted by private customers. In this paper, we provide an overview of modelling methodologies used to project hydrogen refueling infrastructure requirements to support FCEV adoption, and we describe, in detail, the National Renewable Energy Laboratory’s scenario evaluation and regionalization analysis (SERA model. As an example, we use SERA to explore two alternative scenarios of FCEV adoption: one in which FCEV deployment is limited to California and several major cities in the United States; and one in which FCEVs reach widespread adoption, becoming a major option as passenger vehicles across the entire country. Such scenarios can provide guidance and insights for efforts required to deploy the infrastructure supporting transition toward different levels of hydrogen use as a transportation fuel for passenger vehicles in the United States.

  13. Impacts of urban form on future US passenger-vehicle greenhouse gas emissions

    Energy Technology Data Exchange (ETDEWEB)

    Hankey, Steve; Marshall, Julian D. [Department of Civil Engineering, University of Minnesota, 500 Pillsbury Drive SE, Minneapolis, MN 55455 (United States)

    2010-09-15

    Urban form - for example, sprawl versus infill development - impacts people's daily travel patterns and annual vehicle-kilometers traveled (VKT). This paper explores how urban form impacts greenhouse gas (GHG) emissions from passenger-vehicles, the largest source of urban transportation GHG emissions. Our research uses a recently published urban scaling rule to develop six scenarios for high- and low-sprawl US urban growth. We develop and apply a Monte Carlo approach that describes ensemble statistics for several dozen urban areas rather than forecasting changes in individual urban areas. Then, employing three vehicle- and fuel-technology scenarios, we estimate total passenger VKT and resulting GHG emissions for US urban areas. Our results indicate that comprehensive compact development could reduce US 2000-2020 cumulative emissions by up to 3.2 GtCO{sub 2}e (15-20% of projected cumulative emissions). In general, vehicle GHG mitigation may involve three types of approaches: more-efficient vehicles, lower-GHG fuels, and reduced VKT. Our analyses suggest that all three categories must be evaluated; otherwise, improvements in one or two areas (e.g., vehicle fuel economy, fuel carbon content) can be offset by backsliding in a third area (e.g., VKT growth). (author)

  14. Impacts of urban form on future US passenger-vehicle greenhouse gas emissions

    International Nuclear Information System (INIS)

    Hankey, Steve; Marshall, Julian D.

    2010-01-01

    Urban form - for example, sprawl versus infill development - impacts people's daily travel patterns and annual vehicle-kilometers traveled (VKT). This paper explores how urban form impacts greenhouse gas (GHG) emissions from passenger-vehicles, the largest source of urban transportation GHG emissions. Our research uses a recently published urban scaling rule to develop six scenarios for high- and low-sprawl US urban growth. We develop and apply a Monte Carlo approach that describes ensemble statistics for several dozen urban areas rather than forecasting changes in individual urban areas. Then, employing three vehicle- and fuel-technology scenarios, we estimate total passenger VKT and resulting GHG emissions for US urban areas. Our results indicate that comprehensive compact development could reduce US 2000-2020 cumulative emissions by up to 3.2 GtCO 2 e (15-20% of projected cumulative emissions). In general, vehicle GHG mitigation may involve three types of approaches: more-efficient vehicles, lower-GHG fuels, and reduced VKT. Our analyses suggest that all three categories must be evaluated; otherwise, improvements in one or two areas (e.g., vehicle fuel economy, fuel carbon content) can be offset by backsliding in a third area (e.g., VKT growth).

  15. A Numerical Study on Rear-spoiler of Passenger Vehicle

    OpenAIRE

    Xu-xia Hu; Eric T. T. Wong

    2011-01-01

    The simulation of external aerodynamics is one of the most challenging and important automotive CFD applications. With the rapid developments of digital computers, CFD is used as a practical tool in modern fluid dynamics research. It integrates fluid mechanics disciplines, mathematics and computer science. In this study, two different types of simulations were made, one for the flow around a simplified high speed passenger car with a rear-spoiler and the other for the flow without a rear-spoi...

  16. The use of virtual reality and physical tools in the development and validation of ease of entry and exit in passenger vehicles.

    Science.gov (United States)

    Lawson, Glyn; Herriotts, Paul; Malcolm, Louise; Gabrecht, Katharina; Hermawati, Setia

    2015-05-01

    Ease of entry and exit is important for creating a positive first impression of a car and increasing customer satisfaction. Several methods are used within vehicle development to optimise ease of entry and exit, including CAD reviews, benchmarking and buck trials. However, there is an industry trend towards digital methods to reduce the costs and time associated with developing physical prototypes. This paper reports on a study of entry strategy in three properties (buck, car, CAVE) in which inconsistencies were demonstrated by people entering a vehicle representation in the CAVE. In a second study industry practitioners rated the CAVE as worse than physical methods for identifying entry and exit issues, and having lower perceived validity and reliability. However, the resource issues associated with building bucks were recognised. Recommendations are made for developing the CAVE and for combinations of methods for use at different stages of a vehicle's development. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  17. Compact gasoline fuel processor for passenger vehicle APU

    Science.gov (United States)

    Severin, Christopher; Pischinger, Stefan; Ogrzewalla, Jürgen

    Due to the increasing demand for electrical power in today's passenger vehicles, and with the requirements regarding fuel consumption and environmental sustainability tightening, a fuel cell-based auxiliary power unit (APU) becomes a promising alternative to the conventional generation of electrical energy via internal combustion engine, generator and battery. It is obvious that the on-board stored fuel has to be used for the fuel cell system, thus, gasoline or diesel has to be reformed on board. This makes the auxiliary power unit a complex integrated system of stack, air supply, fuel processor, electrics as well as heat and water management. Aside from proving the technical feasibility of such a system, the development has to address three major barriers:start-up time, costs, and size/weight of the systems. In this paper a packaging concept for an auxiliary power unit is presented. The main emphasis is placed on the fuel processor, as good packaging of this large subsystem has the strongest impact on overall size. The fuel processor system consists of an autothermal reformer in combination with water-gas shift and selective oxidation stages, based on adiabatic reactors with inter-cooling. The configuration was realized in a laboratory set-up and experimentally investigated. The results gained from this confirm a general suitability for mobile applications. A start-up time of 30 min was measured, while a potential reduction to 10 min seems feasible. An overall fuel processor efficiency of about 77% was measured. On the basis of the know-how gained by the experimental investigation of the laboratory set-up a packaging concept was developed. Using state-of-the-art catalyst and heat exchanger technology, the volumes of these components are fixed. However, the overall volume is higher mainly due to mixing zones and flow ducts, which do not contribute to the chemical or thermal function of the system. Thus, the concept developed mainly focuses on minimization of those

  18. Motorcycle crashes potentially preventable by three crash avoidance technologies on passenger vehicles.

    Science.gov (United States)

    Teoh, Eric R

    2018-07-04

    The objective of this study was to identify and quantify the motorcycle crash population that would be potential beneficiaries of 3 crash avoidance technologies recently available on passenger vehicles. Two-vehicle crashes between a motorcycle and a passenger vehicle that occurred in the United States during 2011-2015 were classified by type, with consideration of the functionality of 3 classes of passenger vehicle crash avoidance technologies: frontal crash prevention, lane maintenance, and blind spot detection. Results were expressed as the percentage of crashes potentially preventable by each type of technology, based on all known types of 2-vehicle crashes and based on all crashes involving motorcycles. Frontal crash prevention had the largest potential to prevent 2-vehicle motorcycle crashes with passenger vehicles. The 3 technologies in sum had the potential to prevent 10% of fatal 2-vehicle crashes and 23% of police-reported crashes. However, because 2-vehicle crashes with a passenger vehicle represent fewer than half of all motorcycle crashes, these technologies represent a potential to avoid 4% of all fatal motorcycle crashes and 10% of all police-reported motorcycle crashes. Refining the ability of passenger vehicle crash avoidance systems to detect motorcycles represents an opportunity to improve motorcycle safety. Expanding the capabilities of these technologies represents an even greater opportunity. However, even fully realizing these opportunities can affect only a minority of motorcycle crashes and does not change the need for other motorcycle safety countermeasures such as helmets, universal helmet laws, and antilock braking systems.

  19. 76 FR 28947 - Bus Testing: Calculation of Average Passenger Weight and Test Vehicle Weight, and Public Meeting...

    Science.gov (United States)

    2011-05-19

    ...-0015] RIN 2132-AB01 Bus Testing: Calculation of Average Passenger Weight and Test Vehicle Weight, and... of proposed rulemaking (NPRM) regarding the calculation of average passenger weights and test vehicle... passenger weights and actual transit vehicle loads. Specifically, FTA proposed to change the average...

  20. Ballistic Resistance of Armored Passenger Vehicles: Test Protocols and Quality Methods

    Energy Technology Data Exchange (ETDEWEB)

    Jeffrey M. Lacy; Robert E. Polk

    2005-07-01

    This guide establishes a test methodology for determining the overall ballistic resistance of the passenger compartment of assembled nontactical armored passenger vehicles (APVs). Because ballistic testing of every piece of every component of an armored vehicle is impractical, if not impossible, this guide describes a testing scheme based on statistical sampling of exposed component surface areas. Results from the test of the sampled points are combined to form a test score that reflects the probability of ballistic penetration into the passenger compartment of the vehicle.

  1. Passenger thermal perceptions, thermal comfort requirements, and adaptations in short- and long-haul vehicles.

    Science.gov (United States)

    Lin, Tzu-Ping; Hwang, Ruey-Lung; Huang, Kuo-Tsang; Sun, Chen-Yi; Huang, Ying-Che

    2010-05-01

    While thermal comfort in mass transportation vehicles is relevant to service quality and energy consumption, benchmarks for such comfort that reflect the thermal adaptations of passengers are currently lacking. This study reports a field experiment involving simultaneous physical measurements and a questionnaire survey, collecting data from 2,129 respondents, that evaluated thermal comfort in short- and long-haul buses and trains. Experimental results indicate that high air temperature, strong solar radiation, and low air movement explain why passengers feel thermally uncomfortable. The overall insulation of clothing worn by passengers and thermal adaptive behaviour in vehicles differ from those in their living and working spaces. Passengers in short-haul vehicles habitually adjust the air outlets to increase thermal comfort, while passengers in long-haul vehicles prefer to draw the drapes to reduce discomfort from extended exposure to solar radiation. The neutral temperatures for short- and long-haul vehicles are 26.2 degrees C and 27.4 degrees C, while the comfort zones are 22.4-28.9 degrees C and 22.4-30.1 degrees C, respectively. The results of this study provide a valuable reference for practitioners involved in determining the adequate control and management of in-vehicle thermal environments, as well as facilitating design of buses and trains, ultimately contributing to efforts to achieve a balance between the thermal comfort satisfaction of passengers and energy conserving measures for air-conditioning in mass transportation vehicles.

  2. Bridge Condition Assessment based on Vibration Responses of Passenger Vehicle

    International Nuclear Information System (INIS)

    Miyamoto, Ayaho; Yabe, Akito

    2011-01-01

    In this paper, we propose a new method of assessing the condition of existing short- and medium-span reinforced/prestressed concrete bridges based on vibration monitoring data obtained from a public bus. This paper not only describes details of a prototype monitoring system that uses information technology and sensors capable of providing more accurate knowledge of bridge performance than conventional ways but also shows a few specific examples of bridge condition assessment based on vehicle vibrations measured by using an in-service public bus equipped with vibration measurement instrumentation. This paper also describes a sensitivity analysis of deteriorating bridges based on simulation of the acceleration response of buses conducted by the 'substructure method' employing a finite element model to verify the above bridge performance results. The main conclusions obtained in this study can be summarized as follows: (1) Because the vibration responses of passenger vehicles, such as buses, have a good linear relationship with the vibration responses of the target bridges, the proposed system can be used as a practical monitoring system for bridge condition assessment. (2) The results of sensitivity analysis performed by the substructure method show that bus vibration responses are useful for evaluating target bridge performance. (3) The proposed method was applied to a network of real bridges in a local area to evaluate its effectiveness. The results indicate that the proposed method can be used to prioritize the repair/strengthening works of existing bridges based on various vibration information in order to help bridge administrators establish rational maintenance strategies.

  3. Are the Costs of Reducing Greenhouse Gases from Passenger Vehicles Negative?

    OpenAIRE

    Parry, Ian W.H.

    2006-01-01

    Energy models suggest that the cost of reducing carbon emissions from the transportation sector is high relative to other sectors, such as electricity generation. However, this paper shows that taxes to reduce passenger vehicle emissions produce large net benefits, rather than costs, when account is taken of (a) their impact on reducing non-carbon externalities from passenger vehicle use, and (b) interactions with the broader fiscal system. Both of these considerations also strengthen the cas...

  4. Development of Indian passenger transport

    Energy Technology Data Exchange (ETDEWEB)

    Ramanathan, R. [Indira Ghandi Institute of Development Research, Mumbai (India)

    1998-05-01

    The Indian transport sector has been studied using logistic substitution. The share of rail transport is declining, while road and air transport are increasing. These developments are not desirable from an energy-efficiency perspective. (author)

  5. Comparing the Mass, Energy, and Cost Effects of Lightweighting in Conventional and Electric Passenger Vehicles

    OpenAIRE

    Hofer, Johannes; Wilhelm, Erik; Schenler, Warren

    2014-01-01

    In this work the effect of weight reduction using advanced lightweight materials on the mass, energy use, and cost of conventional and battery electric passenger vehicles is compared. Analytic vehicle simulation is coupled with cost assessment to find the optimal degree of weight reduction minimizing manufacturing and total costs. The results show a strong secondary weight and cost saving potential for the battery electric vehicles, but a higher sensitivity of vehicle energy use to mass reduc...

  6. Fuel conservation and GHG (Greenhouse gas) emissions mitigation scenarios for China’s passenger vehicle fleet

    International Nuclear Information System (INIS)

    Hao, Han; Wang, Hewu; Ouyang, Minggao

    2011-01-01

    Passenger vehicles are the main consumers of gasoline in China. We established a bottom-up model which focuses on the simulation of energy consumptions and greenhouse gas (GHG) emissions growth by China’s passenger vehicle fleet. The fuel conservation and GHG emissions mitigation effects of five measures including constraining vehicle registration, reducing vehicle travel, strengthening fuel consumption rate (FCR) limits, vehicle downsizing and promoting electric vehicle (EV) penetration were evaluated. Based on the combination of these measures, the fuel conservation and GHG emissions mitigation scenarios for China’s passenger vehicle fleet were analyzed. Under reference scenario with no measures implemented, the fuel consumptions and life cycle GHG emissions will reach 520 million tons of oil equivalent (Mtoe) and 2.15 billion tons in 2050, about 8.1 times the level in 2010. However, substantial fuel conservation can be achieved by implementing the measures. By implementing all five measures together, the fuel consumption will reach 138 Mtoe in 2030 and decrease to 126 Mtoe in 2050, which is only 37.1% and 24.3% of the consumption under reference scenario. Similar potential lies in GHG mitigation. The results and scenarios provided references for the Chinese government’s policy-making. -- Highlights: ► We established a bottom-up model to simulate the fuel consumptions and GHG (Greenhouse gas) emissions growth by China’s passenger vehicle fleet. ► Five measures including constraining vehicle registration, reducing vehicle travel, improving fuel efficiency, vehicle downsizing and promoting EV penetration were evaluated. ► The fuel conservation and GHG emissions mitigation scenarios for China’s passenger vehicle fleet were provided as references for policy-making.

  7. 3 CFR - Imports of Certain Passenger Vehicle and Light Truck Tires From the People's Republic of China

    Science.gov (United States)

    2010-01-01

    ... vehicle and light truck tires from the People's Republic of China (China) are being imported into the... 3 The President 1 2010-01-01 2010-01-01 false Imports of Certain Passenger Vehicle and Light Truck... Presidential Determination No. 2009-28 of September 11, 2009 Imports of Certain Passenger Vehicle and Light...

  8. Vehicle Development Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — FUNCTION: Supports the development of prototype deployment platform vehicles for offboard countermeasure systems.DESCRIPTION: The Vehicle Development Laboratory is...

  9. Preventing passenger vehicle occupant injuries by vehicle design--a historical perspective from IIHS.

    Science.gov (United States)

    O'Neill, Brian

    2009-04-01

    Motor vehicle crashes result in some 1.2 million deaths and many more injuries worldwide each year and is one of the biggest public health problems facing societies today. This article reviews the history of, and future potential for, one important countermeasure-designing vehicles that reduce occupant deaths and injuries. For many years, people had urged automakers to add design features to reduce crash injuries, but it was not until the mid-1960s that the idea of pursuing vehicle countermeasures gained any significant momentum. In 1966, the U.S. Congress passed the National Traffic and Motor Vehicle Safety Act, requiring the government to issue a comprehensive set of vehicle safety standards. This was the first broad set of requirements issued anywhere in the world, and within a few years similar standards were adopted in Europe and Australia. Early vehicle safety standards specified a variety of safety designs resulting in cars being equipped with lap/shoulder belts, energy-absorbing steering columns, crash-resistant door locks, high-penetration-resistant windshields, etc. Later, the standards moved away from specifying particular design approaches and instead used crash tests and instrumented dummies to set limits on the potential for serious occupant injuries by crash mode. These newer standards paved the way for an approach that used the marketplace, in addition to government regulation, to improve vehicle safety designs-using crash tests and instrumented dummies to provide consumers with comparative safety ratings for new vehicles. The approach began in the late 1970s, when NHTSA started publishing injury measures from belted dummies in new passenger vehicles subjected to frontal barrier crash tests at speeds somewhat higher than specified in the corresponding regulation. This program became the world's first New Car Assessment Program (NCAP) and rated frontal crashworthiness by awarding stars (five stars being the best and one the worst) derived from head

  10. Comparative analysis of aluminum-air battery propulsion systems for passenger vehicles

    Science.gov (United States)

    Salisbury, J. D.; Behrin, E.; Kong, M. K.; Whisler, D. J.

    1980-02-01

    Three electric propulsion systems using an aluminum air battery were analyzed and compared to the internal combustion engine (ICE) vehicle. The engine and fuel systems of a representative five passenger highway vehicle were replaced conceptually by each of the three electric propulsion systems. The electrical vehicles were constrained by the computer simulation to be equivalent to the ICE vehicle in range and acceleration performance. The vehicle masses and aluminum consumption rates were then calculated for the electric vehicles and these data were used as figures of merit. The Al-air vehicles analyzed were (1) an Al-air battery only electric vehicle; (2) an Al-air battery combined with a nickel zinc secondary battery for power leveling and regenerative braking; and (3) an Al-air battery combined with a flywheel for power leveling and regenerative braking. All three electric systems compared favorably with the ICE vehicle.

  11. Environmental and Financial Evaluation of Passenger Vehicle Technologies in Belgium

    Directory of Open Access Journals (Sweden)

    Maarten Messagie

    2013-11-01

    Full Text Available Vehicles with alternative drive trains are regarded as a promising substitute for conventional cars, considering the growing concern about oil depletion and the environmental impact of our transportation system. However, “clean” technologies will only be viable when they are cost-efficient. In this paper, the environmental impacts and the financial costs of different vehicle technologies are calculated for an average Belgian driver. Environmentally friendly vehicles are compared with conventional petrol and diesel vehicles. The assessments are done from a life cycle perspective. The effect on human health, resources and ecosystems is considered when calculating the environmental impact. The total cost of ownership (TCO model includes the purchase price, registration and road taxes, insurance, fuel or electricity cost, maintenance, tires replacement, technical control, battery leasing and battery replacement. In the presented analysis different vehicle technologies and fuels are compared (petrol, diesel, hybrid electric vehicles (HEVs, battery electric vehicles (BEVs and plug-in hybrid electric vehicles (PHEVs on their level of environmental impact and cost per kilometer. The analysis shows a lower environmental impact for electric vehicles. However, electric vehicles have a higher total cost of ownership compared to conventional vehicles, even though the fuel operating costs are significantly lower. The purchase cost of electric vehicles is highly linked to the size of the battery pack, and not to the size of the electric vehicle. This explains the relative high cost for the electric city cars and the comparable cost for the medium and premium cars.

  12. New fuel consumption standards for Chinese passenger vehicles and their effects on reductions of oil use and CO2 emissions of the Chinese passenger vehicle fleet

    International Nuclear Information System (INIS)

    Wang Zhao; Jin Yuefu; Wang Michael; Wei Wu

    2010-01-01

    A new fuel consumption standard for passenger vehicles in China, the so-called Phase 3 standard, was approved technically in 2009 and will take effect in 2012. This standard aims to introduce advanced energy-saving technologies into passenger vehicles and to reduce the average fuel consumption rate of Chinese new passenger vehicle fleet in 2015 to 7 L/100 km. The Phase 3 standard follows the evaluating system by specifying fuel consumption targets for sixteen individual mass-based classes. Different from compliance with the Phases 1 and 2 fuel consumption standards, compliance of the Phase 3 standard is based on corporate average fuel consumption (CAFC) rates for individual automobile companies. A transition period from 2012 to 2014 is designed for manufacturers to gradually adjust their production plans and introduce fuel-efficient technologies. In this paper, we, the designers of the Phase 3 standard, present the design of the overall fuel consumption reduction target, technical feasibility, and policy implications of the Phase 3 standard. We also explore several enforcement approaches for the Phase 3 standard with financial penalties of non-compliance as a priority. Finally, we estimate the overall effect of the Phase 3 standard on oil savings and CO 2 emission reductions.

  13. 48 CFR 252.229-7009 - Relief from customs duty and value added tax on fuel (passenger vehicles) (United Kingdom).

    Science.gov (United States)

    2010-10-01

    ... and value added tax on fuel (passenger vehicles) (United Kingdom). 252.229-7009 Section 252.229-7009... Relief from customs duty and value added tax on fuel (passenger vehicles) (United Kingdom). As prescribed in 229.402-70(i), use the following clause: Relief from Customs Duty and Value Added Tax on Fuel...

  14. Electric passenger and goods vehicles: A review of UK activities

    International Nuclear Information System (INIS)

    Escombe, F.; Rawnsley, A.

    1993-01-01

    The production of electric-powered vehicles has been reduced to only a few hundred, after several thousand had been produced in Great Britain during the past five years. In the framework of this article, the different components of electric-powered vehicles are being examined regarding the economical situation: such as the vehicle itself, the batteries, the motor and the vehicle control. (BWI) [de

  15. The Simultaneous Vehicle Scheduling and Passenger Service Problem with Flexible Dwell Times

    DEFF Research Database (Denmark)

    Fonseca, Joao Filipe Paiva; Larsen, Allan; van der Hurk, Evelien

    In this talk, we deal with a generalization of the well-known Vehicle Scheduling Problem(VSP) that we call Simultaneous Vehicle Scheduling and Passenger Service Problem with Flexible Dwell Times (SVSPSP-FDT). The SVSPSP-FDT generalizes the VSP because the original timetables of the trips can...... be changed (i.e., shifted and stretched) in order to minimize a new objective function that aims at minimizing the operational costs plus the waiting times of the passengers at transfer points. Contrary to most generalizations of the VSP, the SVSPSP-FDT establishes the possibility of changing trips' dwell...... times at important transfer points based on expected passenger ows. We introduce a compact mixed integer linear formulation of the SVSPSP-FDT able to address small instances. We also present a meta-heuristic approach to solve medium/large instances of the problem. The e ectiveness of the proposed...

  16. Assessment of a rail vehicle running with the damaged wheel on a ride comfort for passengers

    Directory of Open Access Journals (Sweden)

    Dižo Ján

    2018-01-01

    Full Text Available In certain conditions rail vehicles wheels can be during operation damaged. Then, the profile of wheels is no longer circular, but it is changed depending on the type and severity of defects. When such rail vehicle with the damaged wheel operates, the quality of a ride comfort for passenger is degraded. This article is focused on the assessment of ride comfort for passenger based on results obtained from dynamic analyses. Simulations and calculations were carried out in commercial multibody software. In our research we considered one type of the railway wheel untrueness – wheel-flat. This type of wheel damaging is relatively common and has such influence on the ride comfort for passenger worsening, which needs to be detected and investigated.

  17. Use of nonlinear asymmetrical shock absorber to improve comfort on passenger vehicles

    Science.gov (United States)

    Silveira, M.; Pontes, B. R.; Balthazar, J. M.

    2014-03-01

    In this study the behaviour of two different types of shock absorbers, symmetrical (linear) and asymmetrical (nonlinear) is compared for use on passenger vehicles. The analyses use different standard road inputs and include variation of the severity parameter, the asymmetry ratio and the velocity of the vehicle. Performance indices and acceleration values are used to assess the efficacy of the asymmetrical systems. The comparisons show that the asymmetrical system, with nonlinear characteristics, tends to have a smoother and more progressive performance, both for vertical and angular movements. The half-car front asymmetrical system was introduced, and the simulation results show that the use of the asymmetrical system only at the front of the vehicle can further diminish the angular oscillations. As lower levels of acceleration are essential for improved ride comfort, the use of asymmetrical systems for vibrations and impact absorption can be a more advantageous choice for passenger vehicles.

  18. Environmental and Financial Evaluation of Passenger Vehicle Technologies in Belgium

    OpenAIRE

    Messagie, Maarten; Lebeau, Kenneth; Coosemans, Thierry; Macharis, Cathy; Mierlo, Joeri van

    2013-01-01

    Vehicles with alternative drive trains are regarded as a promising substitute for conventional cars, considering the growing concern about oil depletion and the environmental impact of our transportation system. However, “clean” technologies will only be viable when they are cost-efficient. In this paper, the environmental impacts and the financial costs of different vehicle technologies are calculated for an average Belgian driver. Environmentally friendly vehicles are compared with conventi...

  19. Stocks, Flows, and Distribution of Critical Metals in Embedded Electronics in Passenger Vehicles.

    Science.gov (United States)

    Restrepo, Eliette; Løvik, Amund N; Wäger, Patrick; Widmer, Rolf; Lonka, Radek; Müller, Daniel B

    2017-02-07

    One of the major applications of critical metals (CMs) is in electrical and electronic equipment (EEE), which is increasingly embedded in other products, notably passenger vehicles. However, recycling strategies for future CM quantities in end-of-life vehicles (ELVs) are poorly understood, mainly due to a limited understating of the complexity of automotive embedded EEE. We introduce a harmonization of the network structure of automotive electronics that enables a comprehensive quantification of CMs in all embedded EEE in a vehicle. This network is combined with a material flow analysis along the vehicle lifecycle in Switzerland to quantify the stocks and flows of Ag, Au, Pd, Ru, Dy, La, Nd, and Co in automotive embedded EEE. In vehicles in use, we calculated 5 -2 +3 t precious metals in controllers embedded in all vehicle types and 220 -60 +90 t rare earth elements (REE); found mainly in five electric motors: alternator, starter, radiator-fan and electronic power steering motor embedded in conventional passenger vehicles and drive motor/generator embedded in hybrid and electric vehicles. Dismantling these devices before ELV shredding, as well as postshredder treatment of automobile shredder residue may increase the recovery of CMs from ELVs. Environmental and economic implications of such recycling strategies must be considered.

  20. Fatal crashes of passenger vehicles before and after adding antilock braking systems.

    Science.gov (United States)

    Farmer, C M; Lund, A K; Trempel, R E; Braver, E R

    1997-11-01

    Fatal crash rates of passenger cars and vans were compared for the last model year before four-wheel antilock brakes were introduced and the first model year for which antilock brakes were standard equipment. Vehicles selected for analysis had no other significant design changes between the model years being compared, and the model years with and without antilocks were no more than two years apart. The overall fatal crash rates were similar for the two model years. However, the vehicles with antilocks were significantly more likely to be involved in crashes fatal to their own occupants, particularly single-vehicle crashes. Conversely, antilock vehicles were less likely to be involved in crashes fatal to occupants of other vehicles or nonoccupants (pedestrians, bicyclists). Overall, antilock brakes appear to have had little effect on fatal crash involvement. Further study is needed to better understand why fatality risk has increased for occupants of antilock vehicles.

  1. Neck sprain after motor vehicle accidents in drivers and passengers

    NARCIS (Netherlands)

    Versteegen, GJ; Kingma, J; Meijler, WJ; ten Duis, HJ

    2000-01-01

    Neck sprain is a general term denoting a soft tissue injury of the neck, which seldom causes major disability but is considered a modem epidemic. The purpose of the present study was to determine the prevalence of sprain of the neck injury due to motor vehicle accidents (MVAs) in both drivers and

  2. The Electric Vehicle Development

    DEFF Research Database (Denmark)

    Wang, Jingyu; Liu, Yingqi; Kokko, Ari

    2014-01-01

    In order to respond to the energy crisis and environment problem, countries carry out their research and promotion about electric vehicles. As the ten cities one thousand new energy buses started in 2009, the new energy vehicles have been greatly developed in China, while the development...... in three aspects-city environment, government and stakeholders. Then the paper discusses the promotion ways and role of government and consumer. Finally, the paper offers some suggestions to promote electric vehicles in China: focusing on feasibility and adaptability of electric vehicles, playing...... of electric vehicles is not that good. This paper selects four cities-Los Angeles, Kanagawa, Hamburg, Amsterdam-that promote electric vehicles successfully and deeply analyzes the development of electric vehicles in these four cities and analyzes the factors that affect the development of electric vehicles...

  3. Comparing the Mass, Energy, and Cost Effects of Lightweighting in Conventional and Electric Passenger Vehicles

    Directory of Open Access Journals (Sweden)

    Johannes Hofer

    2014-09-01

    Full Text Available In this work the effect of weight reduction using advanced lightweight materials on the mass, energy use, and cost of conventional and battery electric passenger vehicles is compared. Analytic vehicle simulation is coupled with cost assessment to find the optimal degree of weight reduction minimizing manufacturing and total costs. The results show a strong secondary weight and cost saving potential for the battery electric vehicles, but a higher sensitivity of vehicle energy use to mass reduction for the conventional vehicle. Generally, light weighting has the potential to lower vehicle costs, however, the results are very sensitive to parameters affecting lifetime fuel costs for conventional and battery costs for electric vehicles. Based on current technology cost estimates it is shown that the optimal amount of primary mass reduction minimizing total costs is similar for conventional and electric vehicles and ranges from 22% to 39%, depending on vehicle range and overall use patterns. The difference between the optimal solutions minimizing manufacturing versus total costs is higher for conventional than battery electric vehicles.

  4. Baseline tests of the C. H. Waterman Renault 5 electric passenger vehicle

    Science.gov (United States)

    Sargent, N. B.; Mcbrien, E. F.; Slavick, R. J.

    1977-01-01

    The Waterman vehicle, a four passenger Renault 5 GTL, performance test results are presented and characterized the state-of-the-art of electric vehicles. It was powered by sixteen 6-volt traction batteries through a two-step contactor controller actuated by a foot throttle to change the voltage applied to the 6.7 -kilowatt motor. The motor output shaft was connected to a front-wheel-drive transaxle that contains a four-speed manual transmission and clutch. The braking system was a conventional hydraulic braking system.

  5. Traffic lanes for vehicles of mass public passenger transport on city streets

    Directory of Open Access Journals (Sweden)

    Gladović Pavle V.

    2015-01-01

    Full Text Available Some of the basic measures of regulating public mass passenger transport in a city network are the introduction and management of traffic lanes reserved for the public transportation. These traffic lanes are important for several reasons: faster moving and shorter travelling time for the vehicles, reducing operating costs, improving the safety, increasing passenger comfort, maintaining of the timetable quality, etc. In most cities, an intensive use of the public transport is concentrated in the morning and the afternoon peak period. The state of the public transport system during these periods is reflected in the crowds inside the vehicles, long vehicle queues at intersections and at bus stops, which cause congestion on the streets and result in delays of public transport vehicles. This paper provides an overview of the current situation on an example in the city of Belgrade. The capacity and the quality of service for the street surfaces reserved for the public transportation vehicles were analysed on the aforementioned example.

  6. New evidence concerning fatal crashes of passenger vehicles before and after adding antilock braking systems.

    Science.gov (United States)

    Farmer, C M

    2001-05-01

    Fatal crash rates for passenger cars and vans were compared for the last model year before four-wheel antilock brakes were introduced and the first model year for which antilock brakes were standard equipment. A prior study, based on fatal crash experience through 1995, reported that vehicle models with antilock brakes were more likely than identical but 1-year-earlier models to be involved in crashes fatal to their own occupants, but were less likely to be involved in crashes fatal to occupants of other vehicles. Overall, there was no significant effect of antilocks on the likelihood of fatal crashes. Similar analyses, based on fatal crash experience during 1996-98, yielded very different results. During 1996-98, vehicles with antilock brakes were again less likely than earlier models to be involved in crashes fatal to occupants of other vehicles, but they were no longer overinvolved in crashes fatal to their own occupants.

  7. Health effects associated with passenger vehicles: monetary values of air pollution.

    Science.gov (United States)

    Marzouk, Mohamed; Madany, Magdy

    2012-01-01

    Air pollution is regarded as one of the highest priorities in environmental protection in both developed and developing countries. High levels of air pollution have adverse effects on human health that might cause premature death. This study presents the monetary value estimates for the adverse human health effects resulted from ambient air pollution. It aids decision makers to set priorities in the public health relevance of pollution abatement. The main driver of policymaker is the need to reduce the avoidable cardiopulmonary morbidity and mortality from pollutant exposures. The monetary valuation involves 2 steps: (i) relate levels of pollutants to mortality and morbidity (concentration-response relationships) and (ii) apply unit economic values. Cost of air pollution associated with passenger vehicles running over a major traffic bridge (6th of October Elevated Highway) is presented as a case study to demonstrate the use of monetary value of air pollution. The study proves that the cost of air pollution is extremely high and should not be overlooked.

  8. Meeting U.S. passenger vehicle fuel economy standards in 2016 and beyond

    International Nuclear Information System (INIS)

    Cheah, Lynette; Heywood, John

    2011-01-01

    New fuel economy standards require new U.S. passenger vehicles to achieve at least 34.1 miles per gallon (MPG) on average by model year 2016, up from 28.8 MPG today. In this paper, the magnitude, combinations and timings of the changes required in U.S. vehicles that are necessary in order to meet the new standards, as well as a target of doubling the fuel economy within the next two decades are explored. Scenarios of future vehicle characteristics and sales mix indicate that the 2016 mandate is aggressive, requiring significant changes starting from today. New vehicles must forgo horsepower improvements, become lighter, and a greater number will use advanced, more fuel-efficient powertrains, such as smaller turbocharged engines, hybrid-electric drives. Achieving a factor-of-two increase in fuel economy by 2030 is also challenging, but more feasible since the auto industry will have more lead time to respond. A discussion on the feasibility of meeting the new fuel economy mandate is included, considering vehicle production planning realities and challenges in deploying new vehicle technologies into the market. - Research Highlights: → The new 2016 fuel economy standards for passenger vehicles in the U.S. can be met, but are aggressive. → Future vehicles must forgo horsepower improvements, become lighter, and a greater number will use advanced, more fuel efficient powertrains. → The challenge of meeting the fuel economy targets is defined by both the magnitude and the timing of these requirements. → Doubling the fuel economy by 2030 is also challenging, but more feasible since the auto industry will have more lead time to respond.

  9. All Electric Passenger Vehicle Sales in India by 2030: Value proposition to Electric Utilities, Government, and Vehicle Owners

    Energy Technology Data Exchange (ETDEWEB)

    Abhyankar, Nikit [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Gopal, Anand R. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sheppard, Colin [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Park, Won Young [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Phadke, Amol A. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2017-06-20

    In India, there is growing interest among policymakers, planners, and regulators for aggressive electrification of passenger vehicles. For example, Piyush Goyal, the Minister of State for India’s Ministry of Coal, Power, New and Renewable Energy, announced an aspirational goal of converting all vehicle sales in India to battery electric vehicles (BEVs) by 2030 (Economic Times, 2016). In 2012, India has already announced the National Mission on Electric Mobility (NMEM) sets a countrywide goal of deploying 6 to 7 million hybrid and electric vehicles (EVs) by 2020 (DHI, 2012). A major policy motivation for transport electrification is to reduce India’s oil import dependency. The objective of this paper is to assess the effect of full electrification of vehicle sales in India by 2030 on the key stakeholders such as BEV owners, electric utilities, and the government. Specifically, we attempt to answer the following questions: (a) How does the total vehicle ownership cost of BEVs compare with the conventional vehicles? (b) What is the additional load due BEV charging? (c) What is the impact on the power sector investments, costs, and utility revenue? (d) How can smart BEV charging help renewable energy grid integration? (e) What is the impact on the crude oil imports? (f) What is the impact on the greenhouse gas (GHG) emissions?

  10. Evaluation of half wave induction motor drive for use in passenger vehicles

    Science.gov (United States)

    Hoft, R. G.; Kawamura, A.; Goodarzi, A.; Yang, G. Q.; Erickson, C. L.

    1985-01-01

    Research performed at the University of Missouri-Columbia to devise and design a lower cost inverter induction motor drive for electrical propulsion of passenger vehicles is described. A two phase inverter motor system is recommended. The new design is predicted to provide comparable vehicle performance, improved reliability and a cost advantage for a high production vehicle, decreased total rating of the power semiconductor switches, and a somewhat simpler control hardware compared to the conventional three phase bridge inverter motor drive system. The major disadvantages of the two phase inverter motor drive are that it is larger and more expensive than a three phase machine, the design of snubbers for the power leakage inductances produce higher transient voltages, and the torque pulsations are relatively large because of the necessity to limit the inverter switching frequency to achieve high efficiency.

  11. Dual vehicle - Development, construction and testing of a dual vehicle for passenger transport on roads and railways. Final report; Zweiwegefahrzeug - Entwicklung, Bau und Erprobung eines Zweiwegefahrzeuges zur Personenbefoerderung Strasse/Schiene. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    This feasibility study investigated a prototype dual vehicle for railways and roads. Technical problems, acceptance specifications, legal and economic aspects were gone into. [German] Zielstellung fuer das Vorhaben war die Untersuchung ausgewaehlter technischer Fragestellungen hinsichtlich der Machbarkeit der Entwicklung und Erprobung eines Prototypes fuer ein Zweiwegefahrzeug fuer den Personenverkehr, das fuer den Einsatz auf der Schiene und der Strasse vorgesehen und dafuer entsprechend technisch ausgestattet ist. Damit erbringt das Vorhaben technisch-konstruktive Loesungsansaetze fuer ein vollstaendig neues Fahrzeuggrundkonzept und traegt hinsichtlich eines solchen zukuenftigen Fahrzeugtyps - zur Klaerung technischer Fragen (statische Zusammenbauuntersuchungen, geometrische und massliche Bedingungen sowie Konzipierung, Leistungsanforderungen der Komponenten, Konzept fuer Ein- und Ausspuren sowie fuer Ein- und Ausstieg), - zur Pruefung der technischen Zulassungsfaehigkeit des Fahrzeuges, - zur Klaerung von Rechtsfragen fuer die Sicherung des Betriebes des Fahrzeuges - sowie zum Nachweis des wirtschaftlicheren Betriebes des Fahrzeuges bei. Das Vorhaben unterbreitet unter Beruecksichtigung sicherheitstechnischer, gesetzlicher und wirtschaftlicher Rahmenbedingungen Loesungsvorschlaege fuer die konstruktive Konzipierung des Fahrgestells und ein technisches Konzept fuer das Ein- und Ausspuren fuer einen neuen Fahrzeugtyp, der sowohl fuer die Strassenbenutzung als auch fuer den Schienenverkehr zugelassen ist. (orig.)

  12. Comparison of policies on vehicle ownership and use between Beijing and Shanghai and their impacts on fuel consumption by passenger vehicles

    International Nuclear Information System (INIS)

    Hao Han; Wang Hewu; Ouyang Minggao

    2011-01-01

    The fast growth of vehicle population in China has caused problems such as traffic congestion and excessive fuel consumption. There have been demands for policy control on growth in private vehicle travel demand. Beijing and Shanghai are China's first two cities to implement policies on vehicle ownership and use. In this paper, we compared policies in the two cities and estimated their impacts on fuel consumption by passenger vehicles. The limitation of vehicle use in Beijing provides limited but immediate reduction in fuel consumption. The limitation of vehicle ownership in Shanghai provides large potential of fuel conservation in a longer term. Under current policy, fuel consumptions by passenger vehicles in Beijing and Shanghai in 2020 were estimated to reach 7.5 and 3.9 billion liters, respectively. The experiences of Beijing and Shanghai are highly relevant for cities in China and abroad that are facing the same problems. - Research Highlights: → Beijing and Shanghai are the first two cities in China to implement policies on vehicle ownership and use. This paper compared policies in the two cities and evaluated their effectiveness. → A bottom-up model was established to simulate the fuel consumption by passenger vehicles. By using this model, fuel consumptions by passenger vehicles in Beijing and Shanghai from 1990 to 2020 under two scenarios of current policy and no policy were estimated. Under current policy, fuel consumptions by passenger vehicles in Beijing and Shanghai in 2020 were estimated to reach 7.5 and 3.9 billion liters, respectively. → This paper discussed the benefits and negative impacts of policies in Beijing and Shanghai, which are highly relevant for cities in China and abroad that are facing the problems of traffic congestion and excessive vehicle fuel consumption.

  13. Ammonia, nitrous oxide and hydrogen cyanide emissions from five passenger vehicles

    International Nuclear Information System (INIS)

    Karlsson, Hua Lu

    2004-01-01

    In this paper, three unregulated components, ammonia, nitrous oxide and hydrogen cyanide, emitted from five passenger vehicles are investigated. With focus upon emission factors from existing production technology, vehicles produced between 1989 and 1998 with considerable mileage (7000 to 280,000) are chosen. Among the five vehicles, four were sold in the European market, whereas one was sold in the US market. The vehicles are tested on a chassis dynamometer. An EU2000 Driving Cycle (NEDC) and a US Urban Driving Cycle (UDC) of the Federal Test Procedure 75 (FTP-75) are used in the study. The regulated emissions are measured using a Horiba Mexa series. Unregulated emissions, ammonia (NH 3 ), nitrous oxide (N 2 O) and hydrogen cyanide (HCN) are analysed by mass spectrometer, gas chromatography and CNT-NA, TIM315-74W method, respectively. Both the unregulated emissions and the regulated emissions show driving cycle dependency; and they are also improved with newer vehicle and emission control technology. However, a gasoline direct injection vehicle (relatively new technology in this study) has rather high regulated emissions, whereas the NH 3 , N 2 O and HCN emissions are low

  14. Ammonia, nitrous oxide and hydrogen cyanide emissions from five passenger vehicles.

    Science.gov (United States)

    Karlsson, Hua Lu

    2004-12-01

    In this paper, three unregulated components, ammonia, nitrous oxide and hydrogen cyanide, emitted from five passenger vehicles are investigated. With focus upon emission factors from existing production technology, vehicles produced between 1989 and 1998 with considerable mileage (7000 to 280,000) are chosen. Among the five vehicles, four were sold in the European market, whereas one was sold in the US market. The vehicles are tested on a chassis dynamometer. An EU2000 Driving Cycle (NEDC) and a US Urban Driving Cycle (UDC) of the Federal Test Procedure 75 (FTP-75) are used in the study. The regulated emissions are measured using a Horiba Mexa series. Unregulated emissions, ammonia (NH(3)), nitrous oxide (N(2)O) and hydrogen cyanide (HCN) are analysed by mass spectrometer, gas chromatography and CNT-NA, TIM315-74W method, respectively. Both the unregulated emissions and the regulated emissions show driving cycle dependency; and they are also improved with newer vehicle and emission control technology. However, a gasoline direct injection vehicle (relatively new technology in this study) has rather high regulated emissions, whereas the NH(3), N(2)O and HCN emissions are low.

  15. Modeling real-world fuel consumption and carbon dioxide emissions with high resolution for light-duty passenger vehicles in a traffic populated city

    International Nuclear Information System (INIS)

    Zhang, Shaojun; Wu, Ye; Un, Puikei; Fu, Lixin; Hao, Jiming

    2016-01-01

    Modeling fuel consumption of light-duty passenger vehicles has created substantial concerns due to the uncertainty from real-world operating conditions. Macao is world-renowned for its tourism industry and high population density. An empirical model is developed to estimate real-world fuel consumption and carbon dioxide emissions for gasoline-powered light-duty passenger vehicles in Macao by considering local fleet configuration and operating conditions. Thanks to increasingly stringent fuel consumption limits in vehicle manufacturing countries, estimated type-approval fuel consumption for light-duty passenger vehicles in Macao by model year was reduced from 7.4 L/100 km in 1995 to 5.9 L/100 km in 2012, although a significant upsizing trend has considerably offset potential energy-saving benefit. However, lower driving speed and the air-conditioning usage tend to raise fleet-average fuel consumption and carbon dioxide emission factors, which are estimated to be 10.1 L/100 km and 240 g/km in 2010. Fleet-total fuel consumption and carbon dioxide emissions are modeled through registered vehicle population-based and link-level traffic demand approaches and the results satisfactorily coincide with the historical record of fuel sales in Macao. Temporal and spatial variations in fuel consumption and carbon dioxide emissions from light-duty passenger vehicles further highlight the importance of effective traffic management in congested areas of Macao. - Highlights: • A fuel consumption model is developed for Macao's light-duty passenger cars. • Increased vehicle size partially offset energy benefit from tightened fuel consumption standard. • Lower speed and use of air-conditioning greatly increase fuel use of Macao light-duty passenger cars. • A high resolution inventory of fuel use and carbon dioxide emissions is built with link-level traffic data. • Policy suggestions are provided to mitigate fuel use in a traffic populated city.

  16. China's fuel economy standards for passenger vehicles. Rationale, policy process, and impacts

    International Nuclear Information System (INIS)

    Oliver, Hongyan H.; Gallagher, Kelly Sims; Tian, Donglian; Zhang, Jinhua

    2009-01-01

    China issued its first Fuel Economy Standards (FES) for light-duty passenger vehicles (LDPV) in September 2004, and the first and second phases of the FES took effective in July 2005 and January 2008, respectively. The stringency of the Chinese FES ranks third globally, following the Japanese and European standards. In this paper, we first review the policy-making background, including the motivations, key players, and the process; and then explain the content and the features of the FES and why there was no compliance flexibility built into it. Next, we assess the various aspects of the standard's impact, including fuel economy improvement, technology changes, shift of market composition, and overall fuel savings. Lastly, we comment on the prospect of tightening the existing FES and summarize the complementary policies that have been adopted or may be considered by the Chinese government for further promoting efficient vehicles and reducing transport energy consumption. The Chinese experience is highly relevant for countries that are also experiencing or anticipating rapid growth in personal vehicles, those wishing to moderate an increase in oil demand, or those desirous of vehicle technology upgrades. (author)

  17. Relationship Between Vehicle Size and Fatality Risk in Model Year 1985-93 Passenger Cars and Light Trucks

    Science.gov (United States)

    1997-01-01

    Fatality rates per million exposure years are computed by make, model and model year, : based on the crash experience of model year 1985-93 passenger cars and light trucks (pickups) vans : and sport utility vehicles) in the United States during calen...

  18. Particle and carbon dioxide emissions from passenger vehicles operating on unleaded petrol and LPG fuel

    International Nuclear Information System (INIS)

    Ristovski, Z.D.; Jayaratne, E.R.; Morawska, L.; Ayoko, G.A.; Lim, M.

    2005-01-01

    A comprehensive study of the particle and carbon dioxide emissions from a fleet of six dedicated liquefied petroleum gas (LPG) powered and five unleaded petrol (ULP) powered new Ford Falcon Forte passenger vehicles was carried out on a chassis dynamometer at four different vehicle speeds-0 (idle), 40, 60, 80 and 100 km h -1 . Emission factors and their relative values between the two fuel types together with a statistical significance for any difference were estimated for each parameter. In general, LPG was found to be a 'cleaner' fuel, although in most cases, the differences were not statistically significant owing to the large variations between emissions from different vehicles. The particle number emission factors ranged from 10 11 to 10 13 km -1 and was over 70% less with LPG compared to ULP. Corresponding differences in particle mass emission factor between the two fuels were small and ranged from the order of 10 μg km -1 at 40 to about 1000 μg km -1 at 100 km h -1 . The count median particle diameter (CMD) ranged from 20 to 35 nm and was larger with LPG than with ULP in all modes except the idle mode. Carbon dioxide emission factors ranged from about 300 to 400 g km -1 at 40 km h -1 , falling with increasing speed to about 200 g km -1 at 100 km h -1 . At all speeds, the values were 10% to 18% greater with ULP than with LPG

  19. PASSENGER CAR EQUIVALENT (PCE OF THROUGH VEHICLES AT SIGNALIZED INTERSECTIONS IN DHAKA METROPOLITAN CITY, BANGLADESH

    Directory of Open Access Journals (Sweden)

    Partha SAHA

    2009-01-01

    PCE currently used in Bangladesh is based on the values given in Geometric Design of Highways (MoC, 2001, which is the modification of the values given by Webster (1958 on the study performed in the United Kingdom in the 50's and 60's. But now-a-days, the situation is far different both for traffic and road user as the characteristics have changed from that time. Hence, in this paper an empirical study was carried out to determine the PCE of different types of vehicle that reflect the actual traffic conditions of Dhaka Metropolitan City. Data were collected from ten signalized intersections and the headway ratio method was used to estimate the PCE of different types of vehicle. The main vehicle compositions observed during the study period consist of passenger cars, auto-rickshaws, mini-buses and buses. The PCE obtained in this study were compared to the values established earlier. It was found that the estimated PCE are smaller than those being used in Bangladesh.

  20. Practicability of passenger vehicle driving emission tests according to new European Union procedures

    Directory of Open Access Journals (Sweden)

    Pielecha Jacek

    2017-01-01

    Full Text Available The article compares driving test data using the latest legislative proposals applicable to passenger cars. Several measurements were performed on the same test route in accordance with the RDE test guidelines, which requires a number of criteria to be met. These criteria include: the length of the measuring segments, their overall test time share, and the dynamic characteristics of the drive. A mobile device for reading the EOBD System information was used to record the engine and vehicle operating parameters during tests. This allowed for the monitoring of parameters such as: load value, engine speed and vehicle velocity. The obtained results were then analyzed for their compatibility with the RDE procedure requirements. Despite the same research route, the obtained results were not the same. The analysis also uses the two-dimensional operating time share characteristics expressed in vehicle velocity and acceleration co-ordinates. As a result it was possible to compare the dynamic properties, share of operating time and, consequently, to check the validity of conducted drive tests in terms of their practicability and emission values.

  1. Rural and Urban Differences in Passenger-Vehicle-Occupant Deaths and Seat Belt Use Among Adults - United States, 2014.

    Science.gov (United States)

    Beck, Laurie F; Downs, Jonathan; Stevens, Mark R; Sauber-Schatz, Erin K

    2017-09-22

    Motor-vehicle crashes are a leading cause of death in the United States. Compared with urban residents, rural residents are at an increased risk for death from crashes and are less likely to wear seat belts. These differences have not been well described by levels of rurality. 2014. Data from the Fatality Analysis Reporting System (FARS) and the Behavioral Risk Factor Surveillance System (BRFSS) were used to identify passenger-vehicle-occupant deaths from motor-vehicle crashes and estimate the prevalence of seat belt use. FARS, a census of U.S. motor-vehicle crashes involving one or more deaths, was used to identify passenger-vehicle-occupant deaths among adults aged ≥18 years. Passenger-vehicle occupants were defined as persons driving or riding in passenger cars, light trucks, vans, or sport utility vehicles. Death rates per 100,000 population, age-adjusted to the 2000 U.S. standard population and the proportion of occupants who were unrestrained at the time of the fatal crash, were calculated. BRFSS, an annual, state-based, random-digit-dialed telephone survey of the noninstitutionalized U.S. civilian population aged ≥18 years, was used to estimate prevalence of seat belt use. FARS and BRFSS data were analyzed by a six-level rural-urban designation, based on the U.S. Department of Agriculture 2013 rural-urban continuum codes, and stratified by census region and type of state seat belt enforcement law (primary or secondary). Within each census region, age-adjusted passenger-vehicle-occupant death rates per 100,000 population increased with increasing rurality, from the most urban to the most rural counties: South, 6.8 to 29.2; Midwest, 5.3 to 25.8; West, 3.9 to 40.0; and Northeast, 3.5 to 10.8. (For the Northeast, data for the most rural counties were not reported because of suppression criteria; comparison is for the most urban to the second-most rural counties.) Similarly, the proportion of occupants who were unrestrained at the time of the fatal crash

  2. Optimal planning of the Nordic transmission system with 100% electric vehicle penetration of passenger cars by 2050

    International Nuclear Information System (INIS)

    Graabak, Ingeborg; Wu, Qiuwei; Warland, Leif; Liu, Zhaoxi

    2016-01-01

    This paper presents the optimal planning of the Nordic backbone transmission system with 100% electric vehicle penetration of passenger cars by 2050. Electric vehicles will play an important role in the future energy systems and can reduce the greenhouse gas emission from the transport sector. However, the electric vehicles will increase the electricity consumption and might induce congestions in the transmission systems. In order to deal with the electricity consumption increase from the electric vehicle integration into the power system and maximize the social welfare, the optimal investments of the Nordic transmission system are studied. Case studies were conducted using the market simulation model EMPS (Efi's multi-area power market simulator) and two electric vehicle charging scenarios: a spot price based scenario and a dumb charging scenario. The electric vehicle charging power is assumed to be 3.68 kW with 1 phase 16 A. The complete electrification of the private passenger fleet increases the yearly power demand in the Nordic region with ca 7.5%. The profitable increases in transmission capacities are highest for dumb charging, but are very low for both dumb and spot price based charging compared to a Reference case. - Highlights: • The electric vehicle distribution is done using population and car statistics. • The 100% penetration electric vehicle demand is obtained for Nordic countries. • The optimal investments in the Nordic transmission system with electric vehicles are studied.

  3. The environmental performance of current and future passenger vehicles: Life cycle assessment based on a novel scenario analysis framework

    International Nuclear Information System (INIS)

    Bauer, Christian; Hofer, Johannes; Althaus, Hans-Jörg; Del Duce, Andrea; Simons, Andrew

    2015-01-01

    Highlights: • We perform Life Cycle Assessment (LCA) of current and future passenger vehicles. • We include gasoline, diesel and natural gas as well as battery and fuel cell cars. • An integrated vehicle simulation framework guarantees consistency. • Only electric cars with “clean” electricity and H_2 allow for pollution mitigation. • Complete LCA is mandatory for environmental evaluation of vehicle technologies. - Abstract: This paper contains an evaluation of the environmental performance of a comprehensive set of current and future mid-size passenger vehicles. We present a comparative Life Cycle Assessment (LCA) based on a novel integrated vehicle simulation framework, which allows for consistency in vehicle parameter settings and consideration of future technological progress. Conventional and hybrid gasoline, diesel and natural gas cars as well as battery and fuel cell electric vehicles (BEV and FCV) are analyzed, taking into account electricity and hydrogen production chains from fossil, nuclear and renewable energy resources. Our results show that a substantial mitigation of climate change can be obtained with electric passenger vehicles, provided that non-fossil energy resources are used for electricity and hydrogen production. However, in terms of other environmental burdens such as acidification, particulate matter formation, and toxicity, BEV may in some cases and FCV are likely to perform worse than modern fossil fueled cars as a consequence of emissions along vehicle and fuel production chains. Therefore, the electrification of road transportation should be accompanied by an integration of life cycle management in vehicle manufacturing chains as well as energy and transport policies in order to counter potential environmental drawbacks.

  4. Exposure to in-vehicle respirable particulate matter in passenger vehicles under different ventilation conditions and seasons

    Directory of Open Access Journals (Sweden)

    Suresh Jain

    2017-03-01

    Full Text Available This study presents the in-vehicle particulate matter (PM concentration in a number of passenger vehicles under various ventilation modes, land use land cover (LULC in different seasons in megacity Delhi, India. In-vehicle monitoring was conducted in buses, cars and autos (three-wheeler using air-conditioned (AC and Non-AC during peak and off-peak hours. The site selected is a ∼15 km long stretch from Punjabi Bagh to Safdarjung Hospital, based on diversity in LULC, availability of vehicles and heavy traffic flow along the direction of travelling. In-vehicle PM was measured using GRIMM aerosol spectrometer and categorised in three classes (PM1, PM2.5 and PM10. The study found that concentration of PM1, PM2.5 and PM10 were significantly (p ≤ 0.05 higher in winters as compared to summers. It was observed that PM concentration was significantly (p ≤ 0.05 higher in Non-AC travel modes compared to AC modes. PM concentrations were high near industrial and commercial areas and during traffic congestion showing the influence of LULC. It is also important to highlight that PM1, PM2.5 and PM10 concentrations were significantly (p ≤ 0.05 higher in case of taxis (cars compared to personal cars which varied from 2.5 to 3.5 times higher in case of AC mode and ∼1.5 times in case of Non-AC mode. Exposures to PM concentration were highest in case of Non-AC bus compared AC-Bus, Non-AC cars, autos and AC-cars. PM concentrations in case of autos and Non-AC cars were almost comparable without any significant (p > 0.05 difference. Regression analysis showed significant correlation between ambient and in-vehicle concentration for PM2.5. Regional deposition fractions were calculated using International Commission on Radiological Protection model to show the deposition in head air-pass, trachea-bronchial and alveolar regions. It was found that deposition of PM1 was highest in the alveolar region.

  5. Optimal Planning of the Nordic Transmission System with 100% Electric Vehicle Penetration of passenger cars by 2050

    DEFF Research Database (Denmark)

    Graabak, Ingeborg; Wu, Qiuwei; Warland, Leif

    2016-01-01

    This paper presents the optimal planning of the Nordic backbone transmission system with 100% electric vehicle penetration of passenger cars by 2050. Electric vehicles will play an important role in the future energy systems and can reduce the greenhouse gas emission from the transport sector....... However, the electric vehicles will increase the electricity consumption and might induce congestions in the transmission systems. In order to deal with the electricity consumption increase from the electric vehicle integration into the power system and maximize the social welfare, the optimal investments...... of the Nordic transmission system are studied. Case studies were conducted using the market simulation model EMPS and two electric vehicle charging scenarios: a spot price based scenario and a dumb charging scenario. The electric vehicle charging power is assumed to be 3.68 kW with 1 phase 16A. The complete...

  6. Retrospective review of adverse incidents involving passengers seated in wheeled mobility devices while traveling in large accessible transit vehicles.

    Science.gov (United States)

    Frost, Karen L; Bertocci, Gina

    2010-04-01

    Characterize wheeled mobility device (WhMD) adverse incidents on large accessible transit vehicles (LATVs) based on vehicle motion, WhMD activity during incident, incident scenario and injury. Retrospective records review. WhMD passengers traveling on LATVs while remaining seated in their. Adverse incidents characterized based on vehicle motion, WhMD activity during incident, and incident scenario. Injury characterized based on outcome, medical attention sought, vehicle activity, WhMD activity and incident scenario. 115 WhMD-related incident reports for years 2000-2005 were analyzed. Most incidents occurred when the LATV was stopped (73.9%), during ingress/egress (42.6%), and at the securement station (33.9%) when the LATV was moving. The combination of WhMD tipping and passenger falling (43.4%) occurred most frequently, and was 1.8 times more likely to occur during ingress/egress than at the securement station. One-third (33.6%) of all incidents resulted in injury, and injuries were equally distributed between ingress/egress (43.6%) and at the securement station (43.6%). WhMD users have a greater chance of incurring injury during ingress/egress than during transit. Research is needed to objectively assess real world transportation experiences of WhMD passengers, and to assess the adequacy of existing federal legislation/guidelines for accessible ramps used in public transportation. Copyright 2009 IPEM. Published by Elsevier Ltd. All rights reserved.

  7. Identification of Drivers in Traffic Accidents and Determination of Passenger Position in a Vehicle by Finger Marks

    Directory of Open Access Journals (Sweden)

    Matej Trapečar

    2012-01-01

    Full Text Available The following paper aims to illustrate certain investigative activities in the forensic analysis and examination of the scene of traffic accidents. When a traffic accident occurs, the scene must be secured as soon as possible to enable professional and proper forensic investigation. Failure to secure the accident scene might result in losing or contaminating the traces, which makes it more difficult to prove or explain trace evidence in further procedure or even makes such evidence inadmissible. The topic is discussed from the viewpoint of crime scene examination, since analysing and investigating traffic accidents requires a great deal of expertise and attention of the investigators. Complex traffic accidents include feigned accidents, hit-and-run accidents as well as accidents in which the driver and passengers, dead or alive, need to be identified. In identifying the passengers, standard criminal investigation methods as well as police forensic and forensic medicine methods are followed. Such methods include confirming the identities with identity documents, other documents and vehicle ownership, fingerprints, biological traces, fibre traces, contact traces, traces of physical injuries on the driver and passengers, etc. According to the results obtained in fingerprint detection on human skin surfaces, this method can also be applied in confirming physical contact between the driver and the passengers in the accident, e.g. in the event of moving the victims and changing the scene of the accident.   Key words: traffic accidents, accident analysis, driver's identity, passengers' position, finger marks, human skin

  8. Evaluation of a high visibility enforcement project focused on passenger vehicles interacting with commercial vehicles.

    Science.gov (United States)

    Thomas, F Dennis; Blomberg, Richard D; Peck, Raymond C; Cosgrove, Linda A; Salzberg, Philip M

    2008-01-01

    In 2004, Washington State applied NHTSA's High Visibility Enforcement model used in the Click It or Ticket seat belt campaign in an attempt to reduce unsafe driving behaviors around commercial motor vehicles (CMVs). The program was called Ticketing Aggressive Cars and Trucks (TACT). This paper details the methods used to evaluate the program's effectiveness and the results of the evaluation. Four high-crash interstate highway corridors, each approximately 25 miles in length, were selected. Two of these corridors received TACT media messages and increased enforcement over an 18-month period while two comparison corridors did not receive any increased media or enforcement. A total of 4,737 contacts were made with drivers during the two enforcement waves, and 72% of these contacts led to a citation. Drivers at the intervention sites who said they saw or heard any of the TACT messages increased from 17.7% in the pre period to a high of 67.3% in the post periods. Drivers at the intervention sites also reported increased exposure to the core message of leaving more space when passing trucks (14% pre to 40% post period). The percentage of drivers who said they leave more room when passing trucks than when passing cars rose from 16% in the pre period to 24% in the post period at the intervention sites, while comparison sites showed no change. Over 150 hours of video recorded by law enforcement officers in unmarked vehicles were utilized to examine violation rates and severity of violations before and after the intervention campaigns. Statistical analyses showed that violation rates were reduced significantly at the intervention sites (between 23% and 46%), while remaining constant at the comparison sites. Analyses of the video data also showed that the seriousness of the residual violations at the intervention sites decreased. Overall, the evaluation results provide a consistent picture of the effectiveness of the TACT pilot project. Success was demonstrated at every step

  9. Developing Singapore Driving Cycle for passenger cars to estimate fuel consumption and vehicular emissions

    Science.gov (United States)

    Ho, Sze-Hwee; Wong, Yiik-Diew; Chang, Victor Wei-Chung

    2014-11-01

    Singapore has pledged to attain 7-11% Business-As-Usual carbon emissions reduction by 2020. Road transport sector is a significant source of carbon emissions, estimated to be the third largest sector in Singapore. A current gap in environmental evaluation for road transport activities in Singapore is the lack of a representative driving cycle for passenger cars (64% of the total population of 974,170 vehicles). This Singapore Driving Cycle (SDC) is hence developed for Singapore roads and traffic conditions. A chase-car (instrumented vehicle) was used to collect on-road data along 12 designed routes, and circulation driving on highly utilized arterial roads (including those in Central Business District (CBD) and both inner and outer ring roads fringing the CBD area). The SDC was thus hence constructed, with consideration of road type proportions, time periods and desired distance, duration and peak-lull proportion. In essence, the SDC is a 2400-s speed-time profile to represent the driving pattern for passenger car in Singapore. Microscopic estimation model (CMEM) shows that, as compared to SDC, the New European Driving Cycle (NEDC) underestimates most of the vehicular emissions (fuel, CO2, HC and NOx by 5%, 5%, 22% and 47%, respectively) and overestimates CO by 8%. The SDC is thus more suitable than the NEDC that is currently in use in Singapore; the SDC can be used to generate more accurate fuel consumption and emissions ratings for various uses (for example, inventory of vehicular emissions and fuel economy labelling).

  10. System safety engineering in the development of advanced surface transportation vehicles

    Science.gov (United States)

    Arnzen, H. E.

    1971-01-01

    Applications of system safety engineering to the development of advanced surface transportation vehicles are described. As a pertinent example, the paper describes a safety engineering efforts tailored to the particular design and test requirements of the Tracked Air Cushion Research Vehicle (TACRV). The test results obtained from this unique research vehicle provide significant design data directly applicable to the development of future tracked air cushion vehicles that will carry passengers in comfort and safety at speeds up to 300 miles per hour.

  11. Characteristics of black carbon emissions from in-use light-duty passenger vehicles.

    Science.gov (United States)

    Zheng, Xuan; Zhang, Shaojun; Wu, Ye; Zhang, K Max; Wu, Xian; Li, Zhenhua; Hao, Jiming

    2017-12-01

    Mitigating black carbon (BC) emissions from various combustion sources has been considered an urgent policy issue to address the challenges of climate change, air pollution and health risks. Vehicles contribute considerably to total anthropogenic BC emissions and urban BC concentrations. Compared with heavy-duty diesel vehicles, there is much larger uncertainty in BC emission factors for light-duty passenger vehicles (LDPVs), in particular for gasoline LDPVs, which warrants further studies. In this study, we employed the dynamometer and the Aethalometer (AE-51) to measure second-by-second BC emissions from eight LDPVs by engine technology and driving cycle. The average BC emission factors under transient cycles (e.g., ECE-15, New European Driving Cycle, NEDC, Worldwide Harmonized Light Vehicles Test Cycle, WLTC) are 3.6-91.5 mg/km, 7.6 mg/km and 0.13-0.58 mg/km, respectively, for diesel (N = 3), gasoline direct injection (GDI) (N = 1) and gasoline port-fuel injection (PFI) engine categories (N = 4). For gasoline PFI LDPVs, the instantaneous emission profiles show a strong association of peak BC emissions with cold-start and high-speed aggressive driving. Such impacts lead to considerable BC emission contributions in cold-start periods (e.g., the first 47 s-94 s) over the entire cycle (e.g., 18-76% of the NEDC and 13-36% of the WLTC) and increased BC emission factors by 80-440% under the WLTC compared to the NEDC. For diesel BC emissions, the size distribution exhibits a typical unimodal pattern with one single peak appearing approximately from 120 to 150 nm, which is largely consistent with previous studies. Nevertheless, the average mass ratios of BC to particle mass (PM) range from 0.38 to 0.54 for three diesel samples, representing substantial impacts from both driving and engine conditions. The significant discrepancy between gasoline BC emission factors obtained from tailpipe exhaust versus ambient conditions suggest that more comparative

  12. Reconciling sectoral abatement strategies with global climate targets: the case of the Chinese passenger vehicle fleet.

    Science.gov (United States)

    Pauliuk, Stefan; Dhaniati, Ni Made A; Müller, Daniel B

    2012-01-03

    The IPCC Forth Assessment Report postulates that global warming can be limited to 2 °C by deploying technologies that are currently available or expected to be commercialized in the coming decades. However, neither specific technological pathways nor internationally binding reduction targets for different sectors or countries have been established yet. Using the passenger car stock in China as example we compute direct CO(2) emissions until 2050 depending on population, car utilization, and fuel efficiency and compare them to benchmarks derived by assuming even contribution of all sectors and a unitary global per capita emission quota. Compared to present car utilization in industrialized countries, massive deployment of prototypes of fuel efficient cars could reduce emissions by about 45%, and moderately lower car use could contribute with another 33%. Still, emissions remain about five times higher than the benchmark for the 2 °C global warming target. Therefore an extended analysis, including in particular low-carbon fuels and the impact of urban and transport planning on annual distance traveled and car ownership, should be considered. A cross-sectoral comparison could reveal whether other sectors could bear an overproportional reduction quota instead. The proposed model offers direct interfaces to material industries, fuel production, and scrap vehicle supply.

  13. Assessing Rates of Global Warming Emissions from Port- Fuel Injection and Gasoline Direct Injection Engines in Light-Duty Passenger Vehicles

    Science.gov (United States)

    Short, D.; , D., Vi; Durbin, T.; Karavalakis, G.; Asa-Awuku, A. A.

    2013-12-01

    Passenger vehicles are known emitters of climate warming pollutants. CO2 from automobile emissions are an anthropogenic greenhouse gas (GHG) and a large contributor to global warming. Worldwide, CO2 emissions from passenger vehicles are responsible for 11% of the total CO2 emissions inventory. Black Carbon (BC), another common vehicular emission, may be the second largest contributor to global warming (after CO2). Currently, 52% of BC emissions in the U.S are from the transportation sector, with ~10% originating from passenger vehicles. The share of pollutants from passenger gasoline vehicles is becoming larger due to the reduction of BC from diesel vehicles. Currently, the majority of gasoline passenger vehicles in the United States have port- fuel injection (PFI) engines. Gasoline direct injection (GDI) engines have increased fuel economy compared to the PFI engine. GDI vehicles are predicted to dominate the U.S. passenger vehicle market in the coming years. The method of gasoline injection into the combustion chamber is the primary difference between these two technologies, which can significantly impact primary emissions from light-duty vehicles (LDV). Our study will measure LDV climate warming emissions and assess the impact on climate due to the change in U.S vehicle technologies. Vehicles were tested on a light- duty chassis dynamometer for emissions of CO2, methane (CH4), and BC. These emissions were measured on F3ederal and California transient test cycles and at steady-state speeds. Vehicles used a gasoline blend of 10% by volume ethanol (E10). E10 fuel is now found in 95% of gasoline stations in the U.S. Data is presented from one GDI and one PFI vehicle. The 2012 Kia Optima utilizes GDI technology and has a large market share of the total GDI vehicles produced in the U.S. In addition, The 2012 Toyota Camry, equipped with a PFI engine, was the most popular vehicle model sold in the U.S. in 2012. Methane emissions were ~50% lower for the GDI technology

  14. Passenger Rail Car Egress -- TRB Workshop

    Science.gov (United States)

    2011-11-01

    The Federal Railroad Administrations (FRA) Office of Railroad Policy and Development is exploring how to enhance regulations that address the safe, timely, and effective emergency evacuation of occupants from passenger rail vehicles in various eme...

  15. KASTOR – A VEHICLE AND CREW SCHEDULING SYSTEM FOR REGULAR BUS PASSENGER TRANSPORT

    Directory of Open Access Journals (Sweden)

    Stanislav PALÚCH

    2017-04-01

    Full Text Available The challenge in vehicle and crew scheduling is to arrange a given set of bus trips into running boards while minimizing certain objectives and complying with a given set of constraints. This scheduling was solved several tens years ago manually by a dispatcher who used his skill, experience, knowledge of history, and intuition. This attitude worked quite well in small instances but could not be applied in larger ones. Development of computers brought opportunities to build computerized vehicle and crew optimization systems. This paper describes a computer system KASTOR developed for vehicle and crew optimization, which complies with the special requirements of Czech and Slovak bus providers, and is significantly different from those in some west European countries.

  16. 78 FR 57822 - Lease and Interchange of Vehicles; Motor Carriers of Passengers

    Science.gov (United States)

    2013-09-20

    ... available to Google Android users and Apple iPhone and iPad users from the respective App Stores, or by... placard, sign, or other permanent or removable device on the right (curb) side of the passenger-carrying...

  17. Study to develop improved fire resistant aircraft passenger seat materials

    Science.gov (United States)

    Duskin, F. E.; Schutter, K. J.; Sieth, H. H.; Trabold, E. L.

    1980-01-01

    The Phase 3 study of the NASA 'Improved Fire Resistant Aircraft Seat Materials' involved fire tests of improved materials in multilayered combinations representative of cushion configurations. Tests were conducted to determine their thermal, smoke, and fire resistance characteristics. Additionally, a 'Design Guideline' for Fire Resistant Passenger Seats was written outlining general seat design considerations. Finally, a three-abreast 'Tourist Class' passenger seat assembly fabricated from the most advanced fire-resistant materials was delivered.

  18. Development of South African vehicle emission factors

    CSIR Research Space (South Africa)

    Forbes, P

    2009-10-01

    Full Text Available for each pollutant, which have been derived from monitoring campaigns in Europe and the USA. In this study, direct exhaust emission monitoring was performed on 58 diesel and 78 petrol passenger vehicles in both idling and accelerated modes. South African...

  19. An observational comparison of the older and younger bus passenger experience in a developing world city.

    Science.gov (United States)

    Aceves-González, Carlos; May, Andrew; Cook, Sharon

    2016-06-01

    This study was an unobtrusive observational analysis of 333 older and younger bus passengers in Guadalajara, Mexico. A set of data were collected for each observed passenger, as well as more general observations related to driver behaviour, bus design and bus service characteristics. There were significant differences between older and younger passengers in terms of boarding and alighting times, use of handrails, seat location preferences, passenger stability and coping strategies in order to maintain postural stability. The conditions of travel are conducive to a poor passenger experience for the older passengers in particular. Although the problems may be attributed to bus design and driver behaviour typical of that in developing countries, they are also influenced by the wider transport infrastructure, and a lack of a regulatory regime which places drivers under time pressure and in direct competition with each other. Practitioner Summary: Bus services must cater for all ages of passengers, including the elderly. This unobtrusive observational study investigated the passenger experience in a developing world city. Bus and wider service design were found to compromise the journey experience, with the older users being particularly negatively impacted. Design recommendations are provided.

  20. The development of hybrid vehicles for the Indian market

    Energy Technology Data Exchange (ETDEWEB)

    Wadhera, R.; Srinivas, A. [Mahindra and Mahindra Ltd., Mumbai (India); Ellinger, R.; Sattler, M. [AVL List GmbH, Graz (Austria)

    2012-11-01

    The passenger vehicle market in India continues to witness a steady growth rate and expected to do so in the future. While the growth rate is primarily driven by the conventional Internal Combustion based engines, Indian automotive industry is exploring various technological options to comply imminent regulations, remain competitive, reduce emissions and ownership cost. Based on the road trials conducted in various parts of India and subsequent analysis of the traffic characteristics, Hybrid Electric Vehicle promises to be appropriate technology for the near future so as to improve fuel efficiency, performance and reduced emissions. Mahindra and Mahindra has established a clear roadmap for development of HEV. Hybrid Electric Vehicles (HEV's) are seen as a major technology route in order to fulfill future automotive demands with regard to fuel efficiency, emissions, performance and drivability. Mahindra and Mahindra has therefore set-up a clear strategy and roadmap for the development and implementation of HEV's in their product portfolio. The development of hybrid electrical vehicle is also confronted by numerous technical challenges such as Thermal Management, Safety Concept, durability requirements and Noise vibration and Harshness. Also the cost-effectiveness needs to be ensured so as to have a bright market penetration and a viable business. This lecture covers the passenger vehicle sales statistics in India, prevailing traffic characteristics in various types of roads, environmental boundaries and challenges encountered for Indian Market. (orig.)

  1. Advanced AC permanent magnet axial flux disc motor for electric passenger vehicle

    Science.gov (United States)

    Kliman, G. B.

    1982-01-01

    An ac permanent magnet axial flux disc motor was developed to operate with a thyristor load commutated inverter as part of an electric vehicle drive system. The motor was required to deliver 29.8 kW (40 hp) peak and 10.4 kW (14 hp) average with a maximum speed of 11,000 rpm. It was also required to run at leading power factor to commutate the inverter. Three motors were built.

  2. Fuel and vehicle technology choices for passenger vehicles in achieving stringent CO2 targets: connections between transportation and other energy sectors.

    Science.gov (United States)

    Grahn, M; Azar, C; Williander, M I; Anderson, J E; Mueller, S A; Wallington, T J

    2009-05-01

    The regionalized Global Energy Transition (GET-R 6.0) model has been modified to include a detailed description of light-duty vehicle options and used to investigate the potential impact of carbon capture and storage (CCS) and concentrating solar power (CSP) on cost-effective fuel/vehicle technologies in a carbon-constrained world. Total CO2 emissions were constrained to achieve stabilization at 400-550 ppm, by 2100, at lowesttotal system cost The dominantfuel/vehicle technologies varied significantly depending on CO2 constraint future cost of vehicle technologies, and availability of CCS and CSP. For many cases, no one technology dominated on a global scale. CCS provides relatively inexpensive low-CO2 electricity and heatwhich prolongs the use of traditional ICEVs. CSP displaces fossil fuel derived electricity, prolongs the use of traditional ICEVs, and promotes electrification of passenger vehicles. In all cases considered, CCS and CSP availability had a major impact on the lowest cost fuel/vehicle technologies, and alternative fuels are needed in response to expected dwindling oil and natural gas supply potential by the end of the century.

  3. Fleet average NOx emission performance of 2004 model year light-duty vehicles, light-duty trucks and medium-duty passenger vehicles

    International Nuclear Information System (INIS)

    2006-05-01

    The On-Road Vehicle and Engine Emission Regulations came into effect on January 1, 2004. The regulations introduced more stringent national emission standards for on-road vehicles and engines, and also required that companies submit reports containing information concerning the company's fleets. This report presented a summary of the regulatory requirements relating to nitric oxide (NO x ) fleet average emissions for light-duty vehicles, light-duty trucks, and medium-duty passenger vehicles under the new regulations. The effectiveness of the Canadian fleet average NO x emission program at achieving environmental performance objectives was also evaluated. A summary of the fleet average NO x emission performance of individual companies was presented, as well as the overall Canadian fleet average of the 2004 model year based on data submitted by companies in their end of model year reports. A total of 21 companies submitted reports covering 2004 model year vehicles in 10 test groups, comprising 1,350,719 vehicles of the 2004 model year manufactured or imported for the purpose of sale in Canada. The average NO x value for the entire Canadian LDV/LDT fleet was 0.2016463 grams per mile. The average NO x values for the entire Canadian HLDT/MDPV fleet was 0.321976 grams per mile. It was concluded that the NO x values for both fleets were consistent with the environmental performance objectives of the regulations for the 2004 model year. 9 tabs

  4. New taxation on passenger vehicles and energy consumption. Impact on energy and CO{sub 2} from changed taxation in April 2007; Nye bilafgifter og energiforbrug. Energi- og CO{sub 2}-maessige effekter af afgiftsaendringen i april 2007

    Energy Technology Data Exchange (ETDEWEB)

    Gravesen, R.; Vestergaard, L.; Hedegaard Soerensen, C. (Tetraplan A/S, Copenhagen (Denmark))

    2009-01-15

    In April 2007 the Danish taxation on passenger vehicles was changed to, amongst other things, lower the CO{sub 2} emission. The changed taxation affects one out of five people, who have purchased a new vehicle for passenger use. And it has improved the overall fuel efficiency of the newly sold passenger vehicles by three percent. However, much of the improvement is based on a shift from gasoline to diesel engines leading to only a slightly lower overall energy consumption and CO{sub 2} emission - about a half percent. The general trend of downsizing and shift from gasoline to diesel engines is only partly due to the changed taxation. Rising oil and fuel prices as well as increased focus on energy consumption and CO{sub 2} emission are the major reason for buying a more fuel efficient vehicle for passenger use. Three out of four people buying new passenger vehicles are willing to choose a more fuel efficient type if the purchase tax and thus the price is lowered. Half of the people buying new passenger vehicles also agree on changing the taxation on passenger vehicles from a purchase based tax, which is quit high in Denmark, to a tax based on the use of the vehicles. Moreover, a majority agree that the taxes on passenger vehicles should, to an even larger extend than today, be based on energy use and CO{sub 2} emission. (au)

  5. Advanced single permanent magnet axipolar ironless stator ac motor for electric passenger vehicles

    Science.gov (United States)

    Beauchamp, E. D.; Hadfield, J. R.; Wuertz, K. L.

    1983-01-01

    A program was conducted to design and develop an advanced-concept motor specifically created for propulsion of electric vehicles with increased range, reduced energy consumption, and reduced life-cycle costs in comparison with conventional systems. The motor developed is a brushless, dc, rare-earth cobalt, permanent magnet, axial air gap inductor machine that uses an ironless stator. Air cooling is inherent provided by the centrifugal-fan action of the rotor poles. An extensive design phase was conducted, which included analysis of the system performance versus the SAE J227a(D) driving cycle. A proof-of-principle model was developed and tested, and a functional model was developed and tested. Full generator-level testing was conducted on the functional model, recording electromagnetic, thermal, aerodynamic, and acoustic noise data. The machine demonstrated 20.3 kW output at 1466 rad/s and 160 dc. The novel ironless stator demonstated the capability to continuously operate at peak current. The projected system performance based on the use of a transistor inverter is 23.6 kW output power at 1466 rad/s and 83.3 percent efficiency. Design areas of concern regarding electric vehicle applications include the inherently high windage loss and rotor inertia.

  6. Theoretical Analysis and Experimental Study on the Coating Removal from Passenger-Vehicle Plastics for Recycling by Using Water Jet Technology

    Science.gov (United States)

    Zhang, Hongshen; Chen, Ming

    2015-11-01

    The recovery and utilization of automotive plastics are a global concern because of the increasing number of end-of-life vehicles. In-depth studies on technologies for the removal of coatings from automotive plastics can contribute to the high value-added levels of the recycling and utilization of automotive plastic. The liquid waste generated by removing chemical paint by using traditional methods is difficult to handle and readily produces secondary pollution. Therefore, new, clean, and highly efficient techniques of paint removal must be developed. In this article, a method of coating removal from passenger-vehicle plastics was generated based on high-pressure water jet technology to facilitate the recycling of these plastics. The established technology was theoretically analyzed, numerically simulated, and experimentally studied. The high-pressure water jet equipment for the removal of automotive-plastic coatings was constructed through research and testing, and the detailed experiments on coating removal rate were performed by using this equipment. The results showed that high-pressure water jet technology can effectively remove coatings on the surfaces of passenger-vehicle plastics. The research also revealed that the coating removal rate increased as jet pressure ( P) increased and then decreased when jet moving speed ( Vn) increased. The rate decreased as the distance from nozzle to work piece ( S nw ) and the nozzle angle ( Φ) increased. The mathematical model for the rate of removal of coatings from bumper surfaces by water jet was derived based on the experiment data and can effectively predict coating removal rate under different operating conditions.

  7. Influence of diffusion of fuel-efficient motor vehicles on gasoline demand for individual user owned passenger cars

    International Nuclear Information System (INIS)

    Sakaguchi, Takahiro

    2000-01-01

    Trends in the demand for petrol in Japan for cars owned by individuals are discussed with reference to expected improvements in fuel efficiency for new models and the results of a survey of user preferences for fuel-efficient vehicles. Demand for petrol in Japan has continued to increase in line with the number of cars used by individual owners. A questionnaire on motor vehicles sent to households found that, while cost and body style were the primary factors in car purchase, three-quarters of respondents would consider buying a low fuel consumption (LFC) version of the model chosen. The influence of LFC vehicles on future demand for petrol was estimated for up to 2015 by combining market timing with consumer preferences. Comparison of the estimated petrol consumption by LFC cars with the Government's requirement for reduced energy use by the transport sector in order to meet its climate change targets indicated a shortfall and a need to increase consumer demand for LFC vehicles. Government measures to reduce energy use in the transport sector, fuel efficiency targets for 2010, major LFC cars, fuel efficiency improvements by major Japanese motor manufacturers and scenarios for assessing the influence of LFC cars are summarised in five tables. Trends in petrol consumption and estimated use by individual user owned passenger cars are shown graphically

  8. Visibility of children behind 2010-2013 model year passenger vehicles using glances, mirrors, and backup cameras and parking sensors.

    Science.gov (United States)

    Kidd, David G; Brethwaite, Andrew

    2014-05-01

    This study identified the areas behind vehicles where younger and older children are not visible and measured the extent to which vehicle technologies improve visibility. Rear visibility of targets simulating the heights of a 12-15-month-old, a 30-36-month-old, and a 60-72-month-old child was assessed in 21 2010-2013 model year passenger vehicles with a backup camera or a backup camera plus parking sensor system. The average blind zone for a 12-15-month-old was twice as large as it was for a 60-72-month-old. Large SUVs had the worst rear visibility and small cars had the best. Increases in rear visibility provided by backup cameras were larger than the non-visible areas detected by parking sensors, but parking sensors detected objects in areas near the rear of the vehicle that were not visible in the camera or other fields of view. Overall, backup cameras and backup cameras plus parking sensors reduced the blind zone by around 90 percent on average and have the potential to prevent backover crashes if drivers use the technology appropriately. Copyright © 2014 Elsevier Ltd. All rights reserved.

  9. Energy Use of Passenger Cars

    DEFF Research Database (Denmark)

    Jørgensen, Kaj

    1998-01-01

    Analysis of the Danish sale and stock of passenger cars, focusing particularly on aspects influencing energy use. The project has tracked the development of vehicle weight, power and fuel economy for both the sale of new cars (from 1980 to 1997)and the stock. In addition, the energy use...

  10. [The use of seatbelts and child seats in drivers and passengers of motor vehicles in four metropolitan areas in Mexico].

    Science.gov (United States)

    Cervantes-Trejo, Arturo; Leenen, Iwin

    2015-01-01

    To estimate the rate of seatbelt and child seat use in drivers and passengers of motor vehicles in four metropolitan areas in Mexico (Guadalajara, León, Monterrey and Mexico City). To evaluate the impact of the Mexican Initiative for Road Safety (IMESEVI) in this respect. Data were collected at the start of IMESEVI (June 2008) and one year after the program's implementation (October 2009) in the four participating metropolitan areas. In particular, the use of seatbelts and child seats was observed in occupants of automobiles, station wagons, and light trucks. The sample included 28,412 (pre) and 52,274 (post) individuals, of which 1,454 (pre) and 1,679 (post) were younger than five years old. The data analysis was based on a hierarchical logistic model. Globally, the probability of using either safety device is 46% (95% CI: 43-49%) at baseline and 52% (95% CI: 48-55%) at the post measurement, with large differences, though, among the four participating metropolitan areas. Factors that significantly affect their use include the individual's position in the vehicle, the type and age of the vehicle, and the individual's sex. Child seat use is very limited. At baseline, about 17% (95% CI: 11-25%) of children below five years old travelled in a special seat, with this number increasing to 26% (95% CI: 19-34%) after the implementation of IMESEVI. Child seat use for children above four years is virtually nonexistent. Continued efforts are required to raise the public awareness of the importance of using safety devices, especially for passengers in the back of the car as well as with respect to the use of adapted seats for small children.

  11. Can UK passenger vehicles be designed to meet 2020 emissions targets? A novel methodology to forecast fuel consumption with uncertainty analysis

    International Nuclear Information System (INIS)

    Martin, Niall P.D.; Bishop, Justin D.K.; Choudhary, Ruchi; Boies, Adam M.

    2015-01-01

    Highlights: • This paper introduces a Bayesian methodology to quantify new car fuel consumption. • Model presents user with more realistic, on-road, fuel consumption estimates. • Sources of NEDC uncertainty attributed to imprecise assumptions for resistances. • Fuel consumption of average UK car projected to exceed 2020 emissions standards. - Abstract: Vehicle manufacturers are required to reduce their European sales-weighted emissions to 95 g CO_2/km by 2020, with the aim of reducing on-road fleet fuel consumption. Nevertheless, current fuel consumption models are not suited for the European market and are unable to account for uncertainties when used to forecast passenger vehicle energy-use. Therefore, a new methodology is detailed herein to quantify new car fleet fuel consumption based on vehicle design metrics. The New European Driving Cycle (NEDC) is shown to underestimate on-road fuel consumption in Spark (SI) and Compression Ignition (CI) vehicles by an average of 16% and 13%, respectively. A Bayesian fuel consumption model attributes these discrepancies to differences in rolling, frictional and aerodynamic resistances. Using projected inputs for engine size, vehicle mass, and compression ratio, the likely average 2020 on-road fuel consumption was estimated to be 7.6 L/100 km for SI and 6.4 L/100 km for CI vehicles. These compared to NEDC based estimates of 5.34 L/100 km (SI) and 4.28 L/100 km (CI), both of which exceeded mandatory 2020 fuel equivalent emissions standards by 30.2% and 18.9%, respectively. The results highlight the need for more stringent technological developments for manufacturers to ensure adherence to targets, and the requirements for more accurate measurement techniques that account for discrepancies between standardised and on-road fuel consumption.

  12. Development Of Fiber Optics For Passenger Car Applications

    Science.gov (United States)

    Steele, R. E.; Schmitt, H. J.

    1987-12-01

    The benefits of fiber optics for telecommunications and Local Area Networks (LANs) are well documented. The benefits to passenger car applications are not as clearly defined. This paper examines the differences between Telecommunications, LAN, and automotive point to point and network applications. Current production automotive applications of optics and fiber optics, automotive data communications trends, and both functional and non-functional requirements and constraints will be described.

  13. THE INJURY SEVERITY RATE DIFFERENCES IN PASSENGER CARS AND PICK UP TRUCKS RELATED TWO VEHICLE INVOLVED MOTOR VEHICLE CRASHES IN BRITISH COLUMBIA, CANADA

    Directory of Open Access Journals (Sweden)

    E.B.R. DESAPRIYA

    2004-01-01

    Full Text Available The effect of large vehicle involvement on motor vehicle crash (MVC rates and severity has long been a concern in MVC analysis literature. Injuries in drivers and occupants are related to several key factors: the mass of the case vehicle and mass of its collision partner and speed of case vehicle and collision partner at the time of the crash. Objective: To evaluate the relative risk of injury occurrence in collisions between picks up trucks (PU and passenger sedan cars (PS. Methods: Data from the Insurance Corporation of British Columbia (ICBC crash data base was used to determine MVC rates and injury occurrence. Descriptive characteristics of the injury location and injury type were analyzed comparing the Odds Ratios and chi-squares. Results: PS occupants received more injuries; Odds Ratio was 2.49 (95% confidence interval: 2.15–2.88. Conclusion: Occupants in PS which collide with PU were at twice the risk of injuries. Concussion, whiplash, lacerations and abrasion were more frequent in PS drivers and occupants than in PU drivers and occupants. Overall, PS drivers/occupants experienced greater injuries than PU drivers/occupants in PU-PS collisions. In this paper, results are shown as odds ratios comparing occupants injuries in PS (case group with occupant injuries in PU (control group.

  14. Nonlinear model predictive control of a passenger vehicle for automated lane changes

    NARCIS (Netherlands)

    Acosta, A.F.; Marquez-Ruiz, A.; Espinosa, J.J.

    2017-01-01

    This article presents a nonlinear Model Predictive Control (MPC) for lane changes, based on a simplified Single Track Model (STM) of the vehicle. The STM includes the position of the vehicle in global coordinates as a state so that the position of the target lane can be specified to the MPC for

  15. Crippling test of a Budd Pioneer passenger car

    Science.gov (United States)

    2012-04-16

    This research program was sponsored by the Federal Railroad Administration (FRA) Office of Research and Development in support of the advancement of improved safety standards for passenger rail vehicles. FRA and the Volpe National Transportation Syst...

  16. Well-to-wheel analysis of direct and indirect use of natural gas in passenger vehicles

    International Nuclear Information System (INIS)

    Curran, Scott J.; Wagner, Robert M.; Graves, Ronald L.; Keller, Martin; Green, Johney B.

    2014-01-01

    The abundance of natural gas in the United States because of the number of existing natural gas reserves and the recent advances in extracting unconventional reserves has been one of the main drivers for low natural gas prices. A question arises of what is the optimal use of natural gas as a transportation fuel. Is it more efficient to use natural gas in a stationary power application to generate electricity to charge electric vehicles, compress natural gas for onboard combustion in vehicles, or re-form natural gas into a denser transportation fuel? This study investigates the well-to-wheels energy use and greenhouse gas emissions from various natural gas to transportation fuel pathways and compares the results to conventional gasoline vehicles and electric vehicles using the US electrical generation mix. Specifically, natural gas vehicles running on compressed natural gas are compared against electric vehicles charged with electricity produced solely from natural gas combustion in stationary power plants. The results of the study show that the dependency on the combustion efficiency of natural gas in stationary power can outweigh the inherent efficiency of electric vehicles, thus highlighting the importance of examining energy use on a well-to-wheels basis. - Highlights: • Well-to-wheels analysis shows differences in use of natural gas for transportation. • Well-to-wheels approach needed to evaluate total energy use and greenhouse gas emissions. • Well-to-wheels energy and GHG (greenhouse gas) emissions depend on efficiency of the prime mover. • Efficiency of power generation critical for low GHG emissions with electric vehicles. • Fuel economy critical for low GHG emissions with compressed natural gas vehicles

  17. Development and applications of GREET 2.7 -- The Transportation Vehicle-Cycle Model

    International Nuclear Information System (INIS)

    Burnham, A.; Wang, M. Q.; Wu, Y.

    2006-01-01

    Argonne National Laboratory has developed a vehicle-cycle module for the Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model. The fuel-cycle GREET model has been cited extensively and contains data on fuel cycles and vehicle operations. The vehicle-cycle model evaluates the energy and emission effects associated with vehicle material recovery and production, vehicle component fabrication, vehicle assembly, and vehicle disposal/recycling. With the addition of the vehicle-cycle module, the GREET model now provides a comprehensive, lifecycle-based approach to compare the energy use and emissions of conventional and advanced vehicle technologies (e.g., hybrid electric vehicles and fuel cell vehicles). This report details the development and application of the GREET 2.7 model. The current model includes six vehicles--a conventional material and a lightweight material version of a mid-size passenger car with the following powertrain systems: internal combustion engine, internal combustion engine with hybrid configuration, and fuel cell with hybrid configuration. The model calculates the energy use and emissions that are required for vehicle component production; battery production; fluid production and use; and vehicle assembly, disposal, and recycling. This report also presents vehicle-cycle modeling results. In order to put these results in a broad perspective, the fuel-cycle model (GREET 1.7) was used in conjunction with the vehicle-cycle model (GREET 2.7) to estimate total energy-cycle results

  18. Development and applications of GREET 2.7 -- The Transportation Vehicle-CycleModel.

    Energy Technology Data Exchange (ETDEWEB)

    Burnham, A.; Wang, M. Q.; Wu, Y.

    2006-12-20

    Argonne National Laboratory has developed a vehicle-cycle module for the Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model. The fuel-cycle GREET model has been cited extensively and contains data on fuel cycles and vehicle operations. The vehicle-cycle model evaluates the energy and emission effects associated with vehicle material recovery and production, vehicle component fabrication, vehicle assembly, and vehicle disposal/recycling. With the addition of the vehicle-cycle module, the GREET model now provides a comprehensive, lifecycle-based approach to compare the energy use and emissions of conventional and advanced vehicle technologies (e.g., hybrid electric vehicles and fuel cell vehicles). This report details the development and application of the GREET 2.7 model. The current model includes six vehicles--a conventional material and a lightweight material version of a mid-size passenger car with the following powertrain systems: internal combustion engine, internal combustion engine with hybrid configuration, and fuel cell with hybrid configuration. The model calculates the energy use and emissions that are required for vehicle component production; battery production; fluid production and use; and vehicle assembly, disposal, and recycling. This report also presents vehicle-cycle modeling results. In order to put these results in a broad perspective, the fuel-cycle model (GREET 1.7) was used in conjunction with the vehicle-cycle model (GREET 2.7) to estimate total energy-cycle results.

  19. Recent evidence concerning higher NO x emissions from passenger cars and light duty vehicles

    Science.gov (United States)

    Carslaw, David C.; Beevers, Sean D.; Tate, James E.; Westmoreland, Emily J.; Williams, Martin L.

    2011-12-01

    Ambient trends in nitrogen oxides (NO x) and nitrogen dioxide (NO 2) for many air pollution monitoring sites in European cities have stabilised in recent years. The lack of a decrease in the concentration of NO x and in particular NO 2 is of concern given European air quality standards are set in law. The lack of decrease in the concentration of NO x and NO 2 is also in clear disagreement with emission inventory estimates and projections. This work undertakes a comprehensive analysis of recent vehicle emissions remote sensing data from seven urban locations across the UK. The large sample size of 84,269 vehicles was carefully cross-referenced to a detailed and comprehensive database of vehicle information. We find that there are significant discrepancies between current UK/European estimates of NO x emissions and those derived from the remote sensing data for several important classes of vehicle. In the case of light duty diesel vehicles it is found that NO x emissions have changed little over 20 years or so over a period when the proportion of directly emitted NO 2 has increased substantially. For diesel cars it is found that absolute emissions of NO x are higher across all legislative classes than suggested by UK and other European emission inventories. Moreover, the analysis shows that more recent technology diesel cars (Euro 3-5) have clear increasing NO x emissions as a function of Vehicle Specific Power, which is absent for older technology vehicles. Under higher engine loads, these newer model diesel cars have a NO x/CO 2 ratio twice that of older model cars, which may be related to the increased use of turbo-charging. Current emissions of NO x from early technology catalyst-equipped petrol cars (Euro 1/2) were also found to be higher than emission inventory estimates - and comparable with NO x emissions from diesel cars. For heavy duty vehicles, it is found that NO x emissions were relatively stable until the introduction of Euro IV technology when

  20. On the development of the new harmonised damage stability regulations for dry cargo and passenger ships

    International Nuclear Information System (INIS)

    Papanikolaou, Apostolos; Eliopoulou, Eleftheria

    2008-01-01

    This paper outlines the methodological background and presents a summary of the main results of a series of undertaken international, IMO-led studies, on the harmonisation of the new probabilistic, risk-based regulations with the currently in-force regulatory provisions for assessing the damage stability of dry cargo and passenger ships. It reviews the historical development of the new regulations, to be applied to all new buildings on January 1, 2009, and the anticipated impact of the new rules on the design and indirect operation of various subcategories of dry cargo and passenger ships. It identifies certain loopholes in the existing regulations that appear cured by the new ones, though certain compromises adopted in the development of the new regulations, particularly those related to large passenger ships' survivability, have left some open issues to be addressed in the near future

  1. Electric vehicles and India's low carbon passenger transport: A long-term co-benefits assessment

    DEFF Research Database (Denmark)

    Dhar, Subash; Pathak, Minal; Shukla, Priyadarshi

    2017-01-01

    Electric vehicles have attracted the attention of India's policy makers as clean technology alternatives due to their multiple advantages like higher efficiency and lower air pollution in short to medium term and reduced CO2 emissions as electricity gets decarbonized in the long-run under low...... carbon scenarios. This paper uses an energy system model ANSWER-MARKAL to analyse the role of electric vehicles (EV) in India. The modelling assessment spans the period 2010 to 2050 and analyses future EV demand in India under three scenarios: i) a ‘Reference’ scenario which includes the continuation...

  2. Heat transfer enhancement of a modularised thermoelectric power generator for passenger vehicles

    International Nuclear Information System (INIS)

    Li, Bo; Huang, Kuo; Yan, Yuying; Li, Yong; Twaha, Ssennoga; Zhu, Jie

    2017-01-01

    Highlights: •Shape-adapted thermoelectric module for highly compact heat recovery exchanger assembly. •Heat pipe-assisted heat transfer enhancement method for better power output. •Highest power output ratio to the total volume of heat recovery exchanger. •Cascaded thermoelectric system can be scaled and extended for various power output. •Self-clamping design of thermoelectric module can solve the thermomechanical imbalances. -- Abstract: Transport represents over a quarter of Europe's greenhouse gas emissions and is the leading cause of air pollution in cities. It has not seen the same gradual decline in emissions as other sectors. Recently, the thermoelectric power generation (TEG) technology emerges as an alternative solution to the emission reduction challenge in this area. In this paper, we present an innovative pathway to an improved heat supply into the concentric shape-adapted TEG modules, integrating the heat pipe technologies. It relies on a phase changing approach which enhances the heat flux through the TEG surface. In order to improve the heat transfer for higher efficiency, in our work, the heat pipes are configured in the radial direction of the exhaust streams. The analysis shows that the power output is adequate for the limited space under the chassis of the passenger car. Much effort can also be applied to obtain enhanced convective heat transfer by adjusting the heat pipes at the dual sides of the concentric TEG modules. Heat enhancement at the hot side of the TEG has an effective impact on the total power out of the TEG modules. However, such improvements can be offset by the adjustment made from the coolant side. Predictably, the whole temperature profile of TEG system is subject to the durability and operational limitations of each component. Furthermore, the results highlight the importance of heat transfer versus the TEG power generation under two possible configurations in the passenger car. The highest power output per

  3. The cost of fuel economy in the Indian passenger vehicle market

    International Nuclear Information System (INIS)

    Chugh, Randy; Cropper, Maureen; Narain, Urvashi

    2011-01-01

    To investigate how fuel economy is valued in the Indian car market, we compute the cost to Indian consumers of purchasing a more fuel-efficient vehicle and compare it to the benefit of lower fuel costs over the life of the vehicle. We estimate hedonic price functions for four market segments (petrol hatchbacks, diesel hatchbacks, petrol sedans, and diesel sedans) to compute 95% confidence intervals for the marginal cost to the consumer for an increase in fuel economy. We find that the associated present value of fuel savings falls within the 95% confidence interval for most specifications, in all market segments, for the years 2002 through 2006. Thus, we fail to consistently reject the hypothesis that consumers appropriately value fuel economy. - Highlights: → We examine the tradeoffs faced by new vehicle consumers in India. → We use hedonic price functions and instrumental variables. → We find no support for the hypothesis that consumers undervalue fuel economy. → Some consumers are willing to forgo substantial potential savings to own their preferred vehicle.

  4. Electric-powered passenger vehicle design study program. Task 1. Tradeoff studies

    Energy Technology Data Exchange (ETDEWEB)

    Rowlett, B.H.

    1976-09-16

    Using the baseline vehicle and power system design established previously to meet the performance goals of the program, three power system computer simulation programs were prepared for the basic vehicle tradeoff studies. These programs simulate the performance of the power system and vehicle over different types of driving conditions such as maximum power acceleration, deceleration, city driving cycles, and hill climbing, and permit accurate determination of the benefits of the unique hybrid power system, the total energy required for the suburban city driving cycle, and the extremes of the operating envelopes of the components so that component design options can be defined and studied. Component design tradeoff studies were conducted, including sensitivity studies to show the criticality of the various losses and unknowns in the analytical models. Also, preliminary vehicle layout studies were performed to determine the best locations of the power system and the batteries. Three basic design options are identified for further study. Economic studies were initiated using analytical models to establish the complete vehicle weight and cost breakdowns. Preliminary reliability and safety studies were completed, and maintainability and safety certification criteria established. The detailed analysis of the power system has verified the feasibility of the system and of the performance expectations. Also, the feasibility of energy recovery from regenerative braking has been confirmed. The sensitivity analysis of the power system shows that sufficient margin for unknown design variables is provided. The preliminary economic analysis indicates that the most difficult objective of the study will be the selection of the cost and weight relationships which are required to achieve the overall cost objectives.

  5. The influence of territory planning and social development on strategic decisions in passenger transport development

    Directory of Open Access Journals (Sweden)

    D. Griškevičienė

    2004-10-01

    Full Text Available The main factors of space planning and social development which play an important role in making strategic decisions in passenger transportation have been analysed. A number of strategic aims based on major principles of territory transport planning have been formulated. The investigation made has shown that the operation of public transport is not closely connected with the main carcass of urban territories. This decreases the efficiency of public transport, making it less popular and competitive compared to automobiles. The creation of the strategy of public transport development for the period of its integration into the EU system requires the use of methods taking into account territory planning and social and economic development of the country. The integration of new territories into the existing transportation system, optimization of routes and the increase of transport service quality are aimed to provide higher living standards and better social and economic conditions for the inhabitants. The appropriate tactical decisions in planning the development of modern passenger transport may be made only if the harmonized and well-grounded strategic aims are defined.

  6. Improved transistorized AC motor controller for battery powered urban electric passenger vehicles

    Science.gov (United States)

    Peak, S. C.

    1982-01-01

    An ac motor controller for an induction motor electric vehicle drive system was designed, fabricated, tested, evaluated, and cost analyzed. A vehicle performance analysis was done to establish the vehicle tractive effort-speed requirements. These requirements were then converted into a set of ac motor and ac controller requirements. The power inverter is a three-phase bridge using power Darlington transistors. The induction motor was optimized for use with an inverter power source. The drive system has a constant torque output to base motor speed and a constant horsepower output to maximum speed. A gear shifting transmission is not required. The ac controller was scaled from the base 20 hp (41 hp peak) at 108 volts dec to an expanded horsepower and battery voltage range. Motor reversal was accomplished by electronic reversal of the inverter phase sequence. The ac controller can also be used as a boost chopper battery charger. The drive system was tested on a dynamometer and results are presented. The current-controlled pulse width modulation control scheme yielded improved motor current waveforms. The ac controller favors a higher system voltage.

  7. Developing infrastructure for electric passenger-cars in the corridor between Southern Scandinavia and Germany

    DEFF Research Database (Denmark)

    Guasco, Clement; Jespersen, Per Homann; Lohse, Sandrina

    2012-01-01

    and academic institutions. A strategy for the development of infrastructure for electric passenger-cars in the corridor was formed using the “Future Creating” methodology. The workshop was part of the SCANDRIA Action Programme and pointed towards ways for e-mobility in the region. The workshop also provided...

  8. Analysis of impacts on urban air quality by restricting the operation of passenger vehicles during Asian Game events in Busan, Korea

    Science.gov (United States)

    Lee, Byeong-Kyu; Jun, Na-Young; Lee, Haengah Kim

    This study is an analysis of the impacts on urban air quality of restricting the operation of passenger vehicles during the 24th Asian Games (AG). Passenger vehicles in Busan were not allowed to operate on the alternative days during the AG period. This restricted operation of passenger vehicles was enforced to improve an urban air quality in Busan during the AG period. The average usage rate of passenger vehicles under an alternate (or restricted) operation was 95.4% and thus the average traffic flow rate (vehicle operation speed) increased approximately 28.1% as compared to normal periods. We analyzed the ambient concentrations of criteria air pollutants measured at 13 air-monitoring stations in Busan (Pusan), Korea, for the three periods of "before (13-28 September 2002)", "during (29 September-14 October 2002)" and "after (15-30 October 2002)" the AG. The 1-h, 24-h and 16-day averages or median concentrations of each classified term were compared to those of other terms. The median concentrations, based on 24-h average data of each day, of PM 10, CO, NO 2, and SO 2 in the ambient during the alternate operation period of 16 days substantially increased as compared to the terms before or after. However, the median concentration of O 3 during the AG period was slightly less than that of the term before. The ambient O 3 concentrations during daytime (12:00-19:00) under alternate operation substantially increased as compared to the terms before or after. However, the ambient O 3 concentrations during nighttime (22:00-07:00) under alternate operation decreased when compared to the terms before or after. For the alternate operation period of passenger vehicles, the average concentrations of PM 10, NO 2, SO 2, and daytime O 3 measured at the air-monitoring stations near the stadiums were much higher than those of the other areas excluding the stadium areas. However, average CO concentrations at the other areas were higher than those nearby the stadiums during the

  9. Passenger train emergency systems : development of prototype railEXODUS software for U.S. passenger rail car egress.

    Science.gov (United States)

    2014-11-01

    The Federal Railroad Administration (FRA), U.S. Department of Transportation (U.S. DOT), is sponsoring a research program, which includes investigation of the applicability of time-based egress performance requirements to U.S. passenger rail cars. Th...

  10. Divers of Passenger Demand

    OpenAIRE

    Wittmer, Andreas

    2011-01-01

    -Overview drivers of passenger demand -Driver 1: Economic growth in developing countries -Driver 2: International business travel in developed countries -Driver 3: International leisure travel in developed countries

  11. Electric vehicles and India's low carbon passenger transport: A long-term co-benefits assessment

    DEFF Research Database (Denmark)

    Dhar, Subash; Pathak, Minal; Shukla, Priyadarshi

    2017-01-01

    Electric vehicles have attracted the attention of India's policy makers as clean technology alternatives due to their multiple advantages like higher efficiency and lower air pollution in short to medium term and reduced CO2 emissions as electricity gets decarbonized in the long-run under low......) are related to sourcing of raw materials for batteries and battery reprocessing and disposal. The findings show that: i) in the reference scenario, the EVs 2-wheelers will achieve a significant share by 2050. Electric 4-wheelers though would have a small share even in 2050; ii) EV push policies though lead...... to significant diffusion of electric 2- wheelers in India by 2030. These policies enhance diffusion of electric 4-wheelers only if financial incentives are sustained in the long-term, iii) the application of global carbon price on the Indian economy in the 2° C stabilization scenario increases competitiveness...

  12. Reusable launch vehicle development research

    Science.gov (United States)

    1995-01-01

    NASA has generated a program approach for a SSTO reusable launch vehicle technology (RLV) development which includes a follow-on to the Ballistic Missile Defense Organization's (BMDO) successful DC-X program, the DC-XA (Advanced). Also, a separate sub-scale flight demonstrator, designated the X-33, will be built and flight tested along with numerous ground based technologies programs. For this to be a successful effort, a balance between technical, schedule, and budgetary risks must be attained. The adoption of BMDO's 'fast track' management practices will be a key element in the eventual success of NASA's effort.

  13. In-situ Study of Seating Static Comfort in Passenger Vehicles

    Directory of Open Access Journals (Sweden)

    Seraj Umi Salmah

    2018-01-01

    Full Text Available In today’s automotive market, comfort is huge selling point of a vehicle. Priority is given by buyers to how comfortable a seat feels during purchase decisions. The measure of comfort is harmonious mix of many aspects such as human ergonomics and physiological factors. However, a gap still exists between objective and subjective measures due to lack of emphasis by past researchers. This is particularly obvious in the lumbar support feature that has still not been able to address the health problems related to driving. This project focuses on bridging the gap by giving users the ability to define true preferred posture in realistic settings. This is done by the creation of a apparatus that allows users to individually manipulate the seat contour for optimum support in more segments than just lumbar area. The experiment is performed in 3 parts, where in each part different segments of the apparatus are manipulatable (lumbar segment, sacral & thoracic segment, and all segments. Sixty human subjects’ statistics are recorded (gender, age, BMI and height and the subjects are palpated to locate internal joints. These joints are marked and postural angles between them are measured using a goniometer. In each seat configuration, the angles are measured and a comfort rating is taken to be compared. It was found that the posture angles are different among the 3 experiments, and there is a change in comfort felt. Some human factors have also been proven to contribute heavily to angles chosen by occupants.

  14. 150 Passenger Commercial Aircraft

    Science.gov (United States)

    Bucovsky, Adrian; Romli, Fairuz I.; Rupp, Jessica

    2002-01-01

    It has been projected that the need for a short-range mid-sized, aircraft is increasing. The future strategy to decrease long-haul flights will increase the demand for short-haul flights. Since passengers prefer to meet their destinations quickly, airlines will increase the frequency of flights, which will reduce the passenger load on the aircraft. If a point-to-point flight is not possible, passengers will prefer only a one-stop short connecting flight to their final destination. A 150-passenger aircraft is an ideal vehicle for these situations. It is mid-sized aircraft and has a range of 3000 nautical miles. This type of aircraft would market U.S. domestic flights or inter-European flight routes. The objective of the design of the 150-passenger aircraft is to minimize fuel consumption. The configuration of the aircraft must be optimized. This aircraft must meet CO2 and NOx emissions standards with minimal acquisition price and operating costs. This report contains all the work that has been performed for the completion of the design of a 150 passenger commercial aircraft. The methodology used is the Technology Identification, Evaluation, and Selection (TIES) developed at Georgia Tech Aerospace Systems Design laboratory (ASDL). This is an eight-step conceptual design process to evaluate the probability of meeting the design constraints. This methodology also allows for the evaluation of new technologies to be implemented into the design. The TIES process begins with defining the problem with a need established and a market targeted. With the customer requirements set and the target values established, a baseline concept is created. Next, the design space is explored to determine the feasibility and viability of the baseline aircraft configuration. If the design is neither feasible nor viable, new technologies can be implemented to open up the feasible design space and allow for a plausible solution. After the new technologies are identified, they must be evaluated

  15. Personal exposures to asbestos fibers during brake maintenance of passenger vehicles.

    Science.gov (United States)

    Cely-García, María Fernanda; Sánchez, Mauricio; Breysse, Patrick N; Ramos-Bonilla, Juan P

    2012-11-01

    Brake linings and brake pads are among the asbestos-containing products that are readily available in Colombia. When sold separated from their support, brake linings require extensive manipulation involving several steps that include drilling, countersinking, riveting, bonding, cutting, beveling, and grinding. Without this manipulation, brake linings cannot be installed in a vehicle. The manipulation process may release asbestos fibers, which may expose brake mechanics to the fibers. Three brake repair shops located in Bogotá (Colombia) were sampled for 3 or 4 consecutive days using US National Institute for Occupational Safety and Health (NIOSH) methods 7400 and 7402. Standard procedures for quality control were followed during the sampling process, and asbestos samples were analyzed by an American Industrial Hygiene Association accredited laboratory. Personal samples were collected to assess full-shift and short-term exposures. Area samples were also collected close to the brake-lining manipulation equipment and within office facilities. Activities were documented during the sampling process. Using Phase Contrast Microscopy Equivalent counts to estimate air asbestos concentrations, all personal samples [i.e. 8-h time-weighted averages (TWAs) and 30-min personal samples] were in compliance with the US Occupational Safety and Health Administration standards. Personal asbestos concentrations based on transmission electron microscopy counts were extremely high, ranging from 0.006 to 3.493 f cm(-3) for 8-h TWA and from 0.015 to 8.835 f cm(-3) for 30-min samples. All asbestos fibers detected were chrysotile. Cleaning facilities and grinding linings resulted in the highest asbestos exposures based on transmission electron microscopy counts. There were also some samples that did not comply with the NIOSH's recommended exposure limits. The results indicate that the brake mechanics sampled are exposed to extremely high asbestos concentrations (i.e. based on transmission

  16. МЕТHОDS OF SYSТЕМ CALCULATION-ANALYTICAL AND STAND DIAGNOSTICATING OF PASSENGER VEHICLES

    Directory of Open Access Journals (Sweden)

    М. Govoruschenko

    2009-01-01

    Full Text Available The new power model for fuel expense diagnosticating is developed on the principle that allows to estimate the general state of vehicles in a simple and accessible way as well as particular units for measuring and analysis of private and general coefficiency of machines.

  17. Competitive Position of Dependent Passenger Car Maintenance Companies – Influences, Developments and Challenges in the German Market

    Directory of Open Access Journals (Sweden)

    Werdich Karl

    2015-06-01

    Full Text Available The presented paper concerns itself with passenger car maintenance companies and their competitiveness. Internal and external influences, change drivers and general changes in the companies and their organisation were identified and analysed. The influence of the development of technology and the diffusion of innovations are highlighted in particular. Under consideration of the competitiveness factors, current and future challenges for the passenger car maintenance companies were worked out. Based on these analyses, future tasks, problem statements and challenges were compiled for passenger car maintenance companies from which other subjects of scientific investigation in area of strategic and economic importance arose.

  18. Energy for road passenger transport and sustainable development: assessing policies and goals interactions

    DEFF Research Database (Denmark)

    Meza, Maria Josefina Figueroa; Ribeiro, Suzana Kahn

    2013-01-01

    and sustainable development goals. Essential, uncertain and limited interactions are mapped out as a result, their overview indicates that a full reconciliation between these policies and sustainability goals is not always attainable. The careful alignment and contextual examination of interactions between...... measures and goals as exemplified in this approach can help inform practical transport energy policy that better match an agenda for sustainable development.......Development that is sustainable requires an operational, efficient and safe transportation system fueled by clean, low-carbon, secure and affordable energy. The energy used in road passenger transport enables social and economic development and is the target of interventions to fight pressing urban...

  19. Development of a dedicated ethanol ultra-low-emissions vehicle (ULEV): Phase 3 report

    Energy Technology Data Exchange (ETDEWEB)

    Dodge, L; Callahan, T; Leone, D; Naegeli, D; Shouse, K; Smith, L; Whitney, K [Southwest Research Inst., San Antonio, TX (United States)

    1998-04-01

    The objective of the 3.5 year project discussed in this report was to develop a commercially competitive vehicle powered by ethanol (or an ethanol blend) that can meet California`s Ultra Low Emissions Vehicle (ULEV) standards and equivalent Corporate Average Fuel Economy (CAFE) energy efficiency for a light duty passenger car application. This particular report summarizes the third phase of the project, which lasted 12 months. Emissions tests were conducted with advanced after-treatment devices on one of the two, almost identical, test vehicles, a 1993 Ford Taurus flexible fuel vehicle. The report also covers tests on the engine removed from the second Taurus vehicle. This engine was modified for an increased compression ratio, fitted with air assist injectors, and included an advanced engine control system with model-based control.

  20. Development of an automated vehicle stop system for cardiac emergencies

    Directory of Open Access Journals (Sweden)

    Tung T. Nguyen

    2017-06-01

    Full Text Available This paper describes the concept and configuration of a novel automated safety vehicle stop system, and a future prospect of the study. Intrinsic sudden death may cause traffic accident since such accidents sometimes involve not only the driver but also other traffic users such as passengers and pedestrians. Cardiovascular disease (CVD is considered as a serious driving risk factor. The pain and others effects of cardiac events degrade driver’s performance, and CVD causes ischemia brought by the CVD induces incapacity of driving. In the automated safety vehicle stop system, which our research group has developed, steer-sensors collects bio-signals and a camera captures the driver’s posture to monitor driver’s incapability. When the driver loses his or her driving capability, the system takes over the maneuver of the vehicle and automatically drives to a safety spot by observing the traffic environment. An emergency scenario was used to demonstrate the system verifying its potential.

  1. Development of vehicle model test-bending of a simple structural surfaces model for automotive vehicle sedan

    Science.gov (United States)

    Nor, M. K. Mohd; Noordin, A.; Ruzali, M. F. S.; Hussen, M. H.; Mustapa@Othman, N.

    2017-04-01

    Simple Structural Surfaces (SSS) method is offered as a means of organizing the process for rationalizing the basic vehicle body structure load paths. The application of this simplified approach is highly beneficial in the development of modern passenger car structure design. In Malaysia, the SSS topic has been widely adopted and seems compulsory in various automotive programs related to automotive vehicle structures in many higher education institutions. However, there is no real physical model of SSS available to gain considerable insight and understanding into the function of each major subassembly in the whole vehicle structures. Based on this motivation, a real physical SSS of sedan model and the corresponding model vehicle tests of bending is proposed in this work. The proposed approach is relatively easy to understand as compared to Finite Element Method (FEM). The results prove that the proposed vehicle model test is useful to physically demonstrate the importance of providing continuous load path using the necessary structural components within the vehicle structures. It is clearly observed that the global bending stiffness reduce significantly when more panels are removed from the complete SSS model. The analysis shows the front parcel shelf is an important subassembly to sustain bending load.

  2. Development and review of Euro 5 passenger car emission factors based on experimental results over various driving cycles

    OpenAIRE

    Fontaras, Georgios; Franco, Vicente; Dilara, Panagiota; Martini, Giorgio; Manfredi, Urbano

    2014-01-01

    The mass emissions of CO2 and regulated pollutants (NOX, HC, CO, PM) of thirteen Euro 5 compliant passenger cars (seven gasoline, six Diesel) were measured on a chassis dynamometer. The vehicles were driven repeatedly over the European type-approval driving cycle (NEDC) and the more dynamic WMTC and CADC driving cycles. Distance-specific emission factors were derived for each pollutant and sub-cycle which were subsequently compared to the corresponding emission factors provided by the referen...

  3. Avoiding, transforming, transitioning: pathways to sustainable low carbon passenger transport in developing countries

    DEFF Research Database (Denmark)

    Meza, Maria Josefina Figueroa; Fulton, Lewis; Tiwari, Geetam

    2013-01-01

    This review examines conditions affecting road passenger transport in developing countries that can be instrumental to building a pathway for reducing carbon emissions while concurrently meeting sustainable development goals. By contrasting present and future status of these conditions a vision...... in motorized travel are also necessary from OECD countries; the focus there is given to what level of pricing and regulatory interventions could change behavior. The articulation of detailed visions can help clarify and prioritize areas where policy efforts can have great impact. Strong actions are necessary...

  4. Fuel efficiency of the Austrian passenger vehicle fleet-Analysis of trends in the technological profile and related impacts on CO2 emissions

    International Nuclear Information System (INIS)

    Meyer, I.; Wessely, S.

    2009-01-01

    This paper analyzes trends in the technological profile of the Austrian personnel vehicle fleet from 1990 to 2007. This includes the parameters of power, engine size and weight, which beyond the technological efficiency of the motor engine itself, are considered to be the main determinants of the fuel efficiency of the average car stock. Investigating the drivers of ever rising transport related greenhouse gas emissions is crucial in order to derive policies that strive towards more energy-efficient on-road passenger mobility. We focus on the efficacy of technological efficiency improvements in mitigating climate-relevant emissions from car use in light of shifting demand patterns towards bigger, heavier and more powerful cars. The analysis is descriptive in nature and based on a bottom-up database that was originally collated for the purpose of the present study. Technological data on car models, which includes tested fuel consumption, engine size, power and weight, is related to registered car stock and, in parts, to newly registered cars. From this, we obtain an original database of the Austrian passenger car fleet, i.e. information on consumer choice of specific car models, segregated by gasoline and diesel fuelled engines. Conclusions are derived for policies aimed at reducing the fossil fuel consumption of the moving vehicle fleet in order to contribute to a low carbon society.

  5. Developing a Risk Model for Fire in Passenger Ships - Based on Bayesian Belief Network

    OpenAIRE

    Dokmo, Hanne Bjørkås

    2016-01-01

    Passenger ships, especially cruise ships, are rapidly increasing in size. With larger vessels, comes a greater risk to the passengers if something where to happen. A fire on a passenger vessel can spread quickly, and with as much as thousands of people needing to be evacuated many things could go wrong. The issue of the safety on board is therefore crucial to consider, seeing as the consequences could be tremendous. There are three types of passenger ships; Passenger vessel, RoPax vessel and ...

  6. Mitigation potential of greenhouse gas emission and implications on fuel consumption due to clean energy vehicles as public passenger transport in Kathmandu Valley of Nepal: A case study of trolley buses in Ring Road

    International Nuclear Information System (INIS)

    Pradhan, Shreekar; Ale, Bhakta Bahadur; Amatya, Vishwa Bhusan

    2006-01-01

    This paper estimates the consequences in fuel consumption and greenhouse gas emission due to the possible intervention of the electric run trolley buses in the existing public transport system in a particular road up to the year 2025 in Kathmandu Valley. It projects the scenarios on the basis that the passenger travel demand is the function of population and income. Basically, it uses the Long Range Energy Alternatives Planning System software to develop Business as Usual scenario and the five alternative scenarios. The alternative scenarios are 100% replacement of vehicles catering to mass-transit in the concerned routes, 50% replacement, 25% replacement, stopping future growth of other vehicles catering to mass-transit in the concerned routes and 25% replacement in the first year, and combination scenarios. The results estimate that the passenger travel demand will increase by three folds from the year 2003 to the year 2025. It projects the three-fold increase of the existing vehicle activity by the year 2025 in Business as Usual scenario. The fuel consumption will increase by 2.4 times compared to the year 2003. It estimates the total greenhouse gas (GHG) emission as 8.5 thousands tons in year 2003 which will increase by more than 3 times in year 2025. It estimates that 174.3 thousands t CO 2 e can be avoided in combination scenario. The paper concludes that the intervention of clean energy transport in the existing public transport can have a significant positive impact on the GHG emission and current fuel consumption

  7. Development of the heavy manipulator vehicle system

    International Nuclear Information System (INIS)

    Herbst, C.; Paustian, P.; Kruger, W.

    1993-01-01

    After the severe reactor accident of Tschernobyl in 1986 MaK System started to develop a Heavy Manipulator Vehicle System under contract from German nuclear technology assistance company ''KHG'' (Kerntechnische Hilfsdienst GmbH). The system comprises a remote controlled manipulator vehicle, a mobile mission control stand as well as a transport/service unit. In order to fulfill the high demands of this complex system a couple of new developments had to be started. The paper describes some of these developments and gives an overview about the main features of the Heavy Manipulator Vehicle System (HMV). (author)

  8. Development of a lightweight fuel cell vehicle

    Science.gov (United States)

    Hwang, J. J.; Wang, D. Y.; Shih, N. C.

    This paper described the development of a fuel cell system and its integration into the lightweight vehicle known as the Mingdao hydrogen vehicle (MHV). The fuel cell system consists of a 5-kW proton exchange membrane fuel cell (PEMFC), a microcontroller and other supported components like a compressed hydrogen cylinder, blower, solenoid valve, pressure regulator, water pump, heat exchanger and sensors. The fuel cell not only propels the vehicle but also powers the supporting components. The MHV performs satisfactorily over a hundred-kilometer drive thus validating the concept of a fuel cell powered zero-emission vehicle. Measurements further show that the fuel cell system has an efficiency of over 30% at the power consumption for vehicle cruise, which is higher than that of a typical internal combustion engine. Tests to improve performance such as speed enhancement, acceleration and fuel efficiency will be conducted in the future work. Such tests will consist of hybridizing with a battery pack.

  9. Measurement of the stress affecting drivers and passengers induced by dust and vehicle exhausts of metropolitan traffic

    International Nuclear Information System (INIS)

    Roemmelt, H.; Hoeppe, P.; Praml, G.; Schierl, R.; Zielinsky, M.

    1993-01-01

    The metropolitan traffic stresses in like manner the bus driver and the passenger by raised concentrations of traffic emissions. We will determine quantitatively the concentrations of dust, dust adsorbed elements (lead, platinum, PAH's), anorganic noxious gases (carbon monoxide, nitrogen dioxide, sulfur dioxide) and the organic poisonous gases ( a.o. benzene, toluene, xylenes) in their distribution in place and time in buses and trams. (orig.) [de

  10. Development of a Novel System to Measure a Clearance of a Passenger Platform

    Science.gov (United States)

    Shimizu, M.; Oizumi, J.; Matsuoka, R.; Takeda, H.; Okukura, H.; Ooya, A.; Koike, A.

    2016-06-01

    Clearances of a passenger platform at a railway station should be appropriately maintained for safety of both trains and passengers. In most Japanese railways clearances between a platform and a train car is measured precisely once or twice a year. Because current measurement systems operate on a track, the closure of the track is unavoidable. Since the procedure of the closure of a track is time-consuming and bothersome, we decided to develop a new system to measure clearances without the closure of a track. A new system is required to work on a platform and the required measurement accuracy is less than several millimetres. We have adopted a 3D laser scanner and stop-and-go operation for a new system. The current systems on a track measure clearances continuously at walking speed, while our system on a platform measures clearances at approximately ten metres intervals. The scanner controlled by a PC acquires a set of point data at each measuring station. Edge points of the platform, top and side points of two rails are detected from the acquired point data. Finally clearances of the platform are calculated by using the detected feature points of the platform and the rails. The results of an experiment using a prototype of our system show that the measurement accuracy by our system would be satisfactory, but our system would take more time than the current systems. Since our system requires no closure of a track, we conclude that our system would be convenient and effective.

  11. Current challenges in autonomous vehicle development

    Science.gov (United States)

    Connelly, J.; Hong, W. S.; Mahoney, R. B., Jr.; Sparrow, D. A.

    2006-05-01

    The field of autonomous vehicles is a rapidly growing one, with significant interest from both government and industry sectors. Autonomous vehicles represent the intersection of artificial intelligence (AI) and robotics, combining decision-making with real-time control. Autonomous vehicles are desired for use in search and rescue, urban reconnaissance, mine detonation, supply convoys, and more. The general adage is to use robots for anything dull, dirty, dangerous or dumb. While a great deal of research has been done on autonomous systems, there are only a handful of fielded examples incorporating machine autonomy beyond the level of teleoperation, especially in outdoor/complex environments. In an attempt to assess and understand the current state of the art in autonomous vehicle development, a few areas where unsolved problems remain became clear. This paper outlines those areas and provides suggestions for the focus of science and technology research. The first step in evaluating the current state of autonomous vehicle development was to develop a definition of autonomy. A number of autonomy level classification systems were reviewed. The resulting working definitions and classification schemes used by the authors are summarized in the opening sections of the paper. The remainder of the report discusses current approaches and challenges in decision-making and real-time control for autonomous vehicles. Suggested research focus areas for near-, mid-, and long-term development are also presented.

  12. Licensing of non intrusive inspection equipment s for load and passengers vehicles that use X rays with energies up to 9 MeV. Mexican experience

    International Nuclear Information System (INIS)

    Munoz M, G. A.; Jimenez C, I.

    2013-10-01

    In the last years and like part of the extensive program of national security, in Mexico have been introduced a great quantity of non intrusive inspection equipment s for load and passengers vehicles that use X rays up to 9 MeV. Due to the great variety of equipment s, the Comision Nacional de Seguridad Nuclear y Salvaguardias (Mexican regulator organ) has established specific guidelines for their licensing and use supervision. In this work the adopted guidelines are exposed in the technical and administrative evaluation for the later licensing of these equipment s. Relative particular questions to the site of these equipment s and the impact in the public opinion that their use can generate are discussed. (author)

  13. Estimates the Emission of Passenger Cars Based on the First Developed Driving Cycle in Nakhon Ratchasima Municipality, Thailand

    Directory of Open Access Journals (Sweden)

    Muangnak Noppatsorn

    2017-01-01

    Full Text Available This study aims to estimate emissions of passenger cars traveled on the highways in Nakhon Ratchasima Municipality (NRM based on recently developed driving cycles. A mobile phone application (SafeMate was used to record speed-time of passenger car on the highways both weekday and weekend. The results showed that the driving cycles of the passenger cars on highway 224 and 304 were quite different. More traffic congestion on highway 224 impacted the average speeds, ranging from 10 to 34 km/h with longer idling time. The average speeds on highway 304 ranged from 49 to 69 km/h with more cruise time. The combined driving cycles on both highways showed the average speeds of 20-40 km/h depending upon the time of days. The traffic density on weekday was higher than the weekend. Peak-hour weekday showed lower traffic flow than off-peak hour which was the opposite of the weekend. Based on the derived driving cycles, the passenger car traveled on the highways in NRM emitted CO, NOx and HC approximately 90.7-129.8, 25.5-34.5 and 6.9-11.7 tons/year, respectively. The passenger cars were estimated to emit about 13,927.7-20,419.3 tons/year of carbon dioxide on the highways. The highway 2 accounted more of the emissions due to the traffic volume and coverage distance in NRM.

  14. Analysis of environmental factors impacting the life cycle cost analysis of conventional and fuel cell/battery-powered passenger vehicles. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-01-31

    This report presents the results of the further developments and testing of the Life Cycle Cost (LCC) Model previously developed by Engineering Systems Management, Inc. (ESM) on behalf of the U.S. Department of Energy (DOE) under contract No. DE-AC02-91CH10491. The Model incorporates specific analytical relationships and cost/performance data relevant to internal combustion engine (ICE) powered vehicles, battery powered electric vehicles (BPEVs), and fuel cell/battery-powered electric vehicles (FCEVs).

  15. Development Concept of the Dubrovnik Passenger Port for Accommodation of Large Cruise Vessels

    Directory of Open Access Journals (Sweden)

    Nina Perko

    2007-11-01

    Full Text Available The technical, traffic and economic parameters of the p011of Dubrovnik, specialized in goods traffic, allow for its reorganizationand conversion into a multi-purpose terminal able toaccommodate cruise ships. The following is required for its successfulconversion: development strategy analysis, financial ratioanalysis and conversion effect analysis. The paper providesthe definition and analysis of the components affecting theidentification of the port of Dubrovnik space requirements withthe aim of defining possible indicators of the port future dimensionswith respect to both, its sea and land area. The pwpose ofthis study is to reveal the advantages and disadvantages of theport of Dubrovnik as a passenger port with respect to both thenational liners and international cn1isers. The questions relatedto finding the optimal solutions for the port facilities and servicescan only be resolved by perceiving all the factors impactingthe traffic in the port, no matter whether marine or overlandconnecting the port with the highway and the airport.

  16. Development of natural gas vehicles in China

    Energy Technology Data Exchange (ETDEWEB)

    Zongmin, Cheng

    1996-12-31

    Past decade and current status of development of natural gas vehicles (NGVs) in China is described. By the end of 1995, 35 CNG refueling stations and 9 LPG refueling stations had been constructed in 12 regions, and 33,100 vehicles had been converted to run on CNG or LPG. China`s automobile industry, a mainstay of the national economy, is slated for accelerated development over next few years. NGVs will help to solve the problems of environment protection, GHGs mitigation, and shortage of oil supply. The Chinese government has started to promote the development of NGVs. Projects, investment demand, GHG mitigation potential, and development barriers are discussed. China needs to import advanced foreign technologies of CNGs. China`s companies expect to cooperate with foreign partners for import of CNG vehicle refueling compressors, conversions, and light cylinders, etc.

  17. Frontier battery development for hybrid vehicles.

    Science.gov (United States)

    Lewis, Heather; Park, Haram; Paolini, Maion

    2012-04-23

    Interest in hybrid-electric vehicles (HEVs) has recently spiked, partly due to an increasingly negative view toward the U.S. foreign oil dependency and environmental concerns. Though HEVs are becoming more common, they have a significant price premium over gasoline-powered vehicles. One of the primary drivers of this "hybrid premium" is the cost of the vehicles' batteries. This paper focuses on these batteries used in hybrid vehicles, examines the types of batteries used for transportation applications and addresses some of the technological, environmental and political drivers in battery development and the deployment of HEVs. This paper examines the claim, often voiced by HEV proponents, that by taking into account savings on gasoline and vehicle maintenance, hybrid cars are cheaper than traditional gasoline cars. This is done by a quantitative benefit-cost analysis, in addition to qualitative benefit-cost analysis from political, technological and environmental perspectives. The quantitative benefit-cost analysis shows that, taking account of all costs for the life of the vehicle, hybrid cars are in fact more expensive than gasoline-powered vehicles; however, after five years, HEVs will break even with gasoline cars. Our results show that it is likely that after 5 years, using hybrid vehicles should be cheaper in effect and yield a positive net benefit to society. There are a number of externalities that could significantly impact the total social cost of the car. These externalities can be divided into four categories: environmental, industrial, R&D and political. Despite short-term implications and hurdles, increased HEV usage forecasts a generally favorable long-term net benefit to society. Most notably, increasing HEV usage could decrease greenhouse gas emissions, while also decreasing U.S. dependence on foreign oil.

  18. Developing infrastructure for electric passenger-cars in the corridor between Southern Scandinavia and Germany - Workshop Protocol

    DEFF Research Database (Denmark)

    Guasco, Clement; Jespersen, Per Homann; Lohse, Sandrina

    2012-01-01

    and academic institutions. A strategy for the development of infrastructure for electric passenger-cars in the corridor was formed using the “Future Creating” methodology. The workshop was part of the SCANDRIA Action Programme and pointed towards ways for e-mobility in the region. The workshop also provided...

  19. Quantifying the Effects of Idle-Stop Systems on Fuel Economy in Light-Duty Passenger Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Jeff Wishart; Matthew Shirk

    2012-12-01

    Vehicles equipped with idle-stop (IS) systems are capable of engine shut down when the vehicle is stopped and rapid engine re-start for the vehicle launch. This capability reduces fuel consumption and emissions during periods when the engine is not being utilized to provide propulsion or to power accessories. IS systems are a low-cost and fast-growing technology in the industry-wide pursuit of increased vehicle efficiency, possibly becoming standard features in European vehicles in the near future. In contrast, currently there are only three non-hybrid vehicle models for sale in North America with IS systems and these models are distinctly low-volume models. As part of the United States Department of Energy’s Advanced Vehicle Testing Activity, ECOtality North America has tested the real-world effect of IS systems on fuel consumption in three vehicle models imported from Europe. These vehicles were chosen to represent three types of systems: (1) spark ignition with 12-V belt alternator starter; (2) compression ignition with 12-V belt alternator starter; and (3) direct-injection spark ignition, with 12-V belt alternator starter/combustion restart. The vehicles have undergone both dynamometer and on-road testing; the test results show somewhat conflicting data. The laboratory data and the portion of the on-road data in which driving is conducted on a prescribed route with trained drivers produced significant fuel economy improvement. However, the fleet data do not corroborate improvement, even though the data show significant engine-off time. It is possible that the effects of the varying driving styles and routes in the fleet testing overshadowed the fuel economy improvements. More testing with the same driver over routes that are similar with the IS system-enabled and disabled is recommended. There is anecdotal evidence that current Environmental Protection Agency fuel economy test procedures do not capture the fuel economy gains that IS systems produce in real

  20. Fuel consumption of business passenger cars and plug-in vehicles; Praktijkverbruik van zakelijke personenauto's en plug-in voertuigen

    Energy Technology Data Exchange (ETDEWEB)

    Ligterink, N.E.; Smokers, R.T.M.

    2013-05-15

    TNO investigates the use and fuel consumption of private cars since 2008. In this report the results for 2012 are presented. In part 1 the most recent results of statistical analyses of fuel card data, which are used by business-type drivers of passenger cars, are presented. The second part contains the results of an analysis of available fuel consumption data of so-called plug-in hybrid electric vehicles and range-extender electric vehicles that have entered the market in 2012 [Dutch] TNO doet al sinds 2008 onderzoek naar het praktijkverbruik van personenauto's. In dit rapport worden de resultaten over 2012 weergegeven. Het eerste deel presenteert de meest recente resultaten van statistische analyses van tankpasdata van door zakelijke rijders gebruikte personenvoertuigen. Het tweede deel bevat de resultaten van een analyse van beschikbare verbruiksgegevens van zogenoemde 'plug-in hybrides' en 'range-extender' elektrische voertuigen die in 2012 op de markt zijn gekomen.

  1. Teen Drivers' Perceptions of Their Peer Passengers: Qualitative Study.

    Science.gov (United States)

    Ehsani, Johnathon P; Haynie, Denise L; Luthers, Christina; Perlus, Jessamyn; Gerber, Eli; Ouimet, Marie Claude; Klauer, Sheila G; Simons-Morton, Bruce

    The presence of peer passengers increases teenage drivers' fatal crash risk. Distraction and social influence are the two main factors that have been associated with increased risk. Teen drivers' perceptions of their peer passengers on these factors could inform our understanding of the conditions under which peer passengers increase crash risk or promote safer driving. The purpose of this study was to examine teen drivers' perceptions of their peer passengers on distraction and social influence. A convenience sample of male and female drivers participated in a semi-structured interview that included questions on their perceptions of the effects of peer passengers on driving on distraction and social influence. The analysis of the interviews was guided by a grounded theory approach. Teenage drivers were aware of the risk that peer passengers posed. Some described having passengers in the vehicle as distracting, and recognized that the level of distraction increased with the number of passengers in the vehicle. Drivers that felt responsible for the safety of their peer passengers described strategies they used to control the in-vehicle environment. Drivers described driving with passengers as a performance, and articulated direct and indirect sources of pressure, gender norms, and unspoken expectations of their passengers as influencing their driving behavior. The influence of passengers is situation specific and dependent on whom the passenger(s) may be. Passenger influence may be either protective or harmful, depending on the circumstances. Some passengers exert direct influence, but often their influence appears more indirect and subtle.

  2. Frontier battery development for hybrid vehicles

    Directory of Open Access Journals (Sweden)

    Lewis Heather

    2012-04-01

    Full Text Available Abstract Background Interest in hybrid-electric vehicles (HEVs has recently spiked, partly due to an increasingly negative view toward the U.S. foreign oil dependency and environmental concerns. Though HEVs are becoming more common, they have a significant price premium over gasoline-powered vehicles. One of the primary drivers of this “hybrid premium” is the cost of the vehicles’ batteries. This paper focuses on these batteries used in hybrid vehicles, examines the types of batteries used for transportation applications and addresses some of the technological, environmental and political drivers in battery development and the deployment of HEVs. Methods This paper examines the claim, often voiced by HEV proponents, that by taking into account savings on gasoline and vehicle maintenance, hybrid cars are cheaper than traditional gasoline cars. This is done by a quantitative benefit-cost analysis, in addition to qualitative benefit-cost analysis from political, technological and environmental perspectives. Results The quantitative benefit-cost analysis shows that, taking account of all costs for the life of the vehicle, hybrid cars are in fact more expensive than gasoline-powered vehicles; however, after five years, HEVs will break even with gasoline cars. Conclusions Our results show that it is likely that after 5 years, using hybrid vehicles should be cheaper in effect and yield a positive net benefit to society. There are a number of externalities that could significantly impact the total social cost of the car. These externalities can be divided into four categories: environmental, industrial, R&D and political. Despite short-term implications and hurdles, increased HEV usage forecasts a generally favorable long-term net benefit to society. Most notably, increasing HEV usage could decrease greenhouse gas emissions, while also decreasing U.S. dependence on foreign oil.

  3. Frontier battery development for hybrid vehicles

    Science.gov (United States)

    2012-01-01

    Background Interest in hybrid-electric vehicles (HEVs) has recently spiked, partly due to an increasingly negative view toward the U.S. foreign oil dependency and environmental concerns. Though HEVs are becoming more common, they have a significant price premium over gasoline-powered vehicles. One of the primary drivers of this “hybrid premium” is the cost of the vehicles’ batteries. This paper focuses on these batteries used in hybrid vehicles, examines the types of batteries used for transportation applications and addresses some of the technological, environmental and political drivers in battery development and the deployment of HEVs. Methods This paper examines the claim, often voiced by HEV proponents, that by taking into account savings on gasoline and vehicle maintenance, hybrid cars are cheaper than traditional gasoline cars. This is done by a quantitative benefit-cost analysis, in addition to qualitative benefit-cost analysis from political, technological and environmental perspectives. Results The quantitative benefit-cost analysis shows that, taking account of all costs for the life of the vehicle, hybrid cars are in fact more expensive than gasoline-powered vehicles; however, after five years, HEVs will break even with gasoline cars. Conclusions Our results show that it is likely that after 5 years, using hybrid vehicles should be cheaper in effect and yield a positive net benefit to society. There are a number of externalities that could significantly impact the total social cost of the car. These externalities can be divided into four categories: environmental, industrial, R&D and political. Despite short-term implications and hurdles, increased HEV usage forecasts a generally favorable long-term net benefit to society. Most notably, increasing HEV usage could decrease greenhouse gas emissions, while also decreasing U.S. dependence on foreign oil. PMID:22540987

  4. Neighborhood electric vehicle market test development project: Sacramento electric transportation consortium Ra 93-23 program. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Warf, W.R.

    1997-02-01

    The neighborhood electric vehicle (NEV) niche is the object of this market and product test project. The project availed itself of a limited production three wheel, single passenger low performance NEV designed and produced in Denmark to determine the acceptability of the design for production and use in North America. This vehicle, as well as a prototype four wheel vehicle designed and constructed through this project, are entirely reinforced plastic chassis and body. Pacific Electric Vehicles was the primary participant in the Project. Included are the evaluation of drive system components, battery charging schemes, body and chassis and glazing material suitability. The project determined and/or verified many of the realities of motor vehicle development and usage in the U.S., which remain more restrictive than elsewhere. Statistical usage data, maintenance requirements, and user experiences are reported and analyzed.

  5. Development process of new bumper beam for passenger car: A review

    International Nuclear Information System (INIS)

    Davoodi, M.M.; Sapuan, S.M.; Aidy, A.; Abu Osman, N.A.; Oshkour, A.A.; Wan Abas, W.A.B.

    2012-01-01

    Highlights: ► The process of new bumper beam development for passenger car is discussed. ► A new bumper system has been added to the previous developed bumper systems. ► The flow chart of design and analysis of bumper beam is shown. ► Different analysis for developing new bumper beam before production is discussed. ► The process of material selection in bumper beam is discussed. -- Abstract: Bumper beam absorbs the accidental kinetic energy by deflection in low-speed impact and by deformation in high-speed impact. The safety regulations “low-, and high-speed, and pedestrian impacts” along with new environmental restrictions “end-of-life vehicles” increased the complexity level of bumper system design. The new bumper design must be flexible enough to reduce the passenger and occupant injury and stay intact in low-speed impact besides being stiff enough to dissipate the kinetic energy in high-speed impact. The reinforcement beam plays a vital role in safety and it must be validated through finite-element analysis (FEA) and experimental tests before mass production. The careful design and analysis of bumper beam effective parameters can optimize the strength, reduce the weight, and increase the possibility of utilizing biodegradable and recyclable materials to reduce the environmental pollution. Developing the correct design and analysis procedures prevents design re-modification. On the other hand, analysis of the most effective parameters conducive to high bumper beam strength increases the efficiency of product development. Cross section, longitudinal curvature, fixing method, rib thickness, and strength are some of the significant design parameters in bumper beam production. This study critically reviews the related literature on bumper design to come up with the optimal bumper beam design process. It particularly focuses on the effective parameters in the design of bumper beam and their most suitable values or ranges of values. The results can

  6. Developments and challenges for autonomous unmanned vehicles

    CERN Document Server

    Finn, Anthony

    2010-01-01

    It is widely anticipated that autonomous vehicles will have a transformational impact on military forces and will play a key role in many future force structures. As a result, many tasks have already been identified that unmanned systems could undertake more readily than humans. However, for this to occur, such systems will need to be agile, versatile, persistent, reliable, survivable and lethal. This will require many of the vehicles 'cognitive' or higher order functions to be more fully developed, whereas to date only the 'component' or physical functions have been successfully automated and

  7. Impact of driving cycle and climate on electrical consumption and range of a fully electric passenger vehicle

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, N; Belzile, M [Transport Canada, Ottawa, ON (Canada); Christenson, M; Edgar, J [Environment Canada, Gatineau, PQ (Canada)

    2010-07-01

    Transport Canada's ecotechnology for vehicles (eTV) program is a $15 million program, operated over 4 years (2007-2011) that strives to encourage the introduction of advanced clean vehicle technologies in Canada. The objectives of eTV's are to reduce barriers to the introduction of clean technologies into light-duty vehicles sold in Canada. The presentation discussed the mandate of the emissions research and measurement section of Environment Canada. The dynamometer test facility, a state-of-the-art emissions testing laboratory capable of conducting comprehensive emissions measurements from a variety of sources was also discussed. Several electric mobility projects were presented. The testing rationale and testing outline were explained. It was concluded that the repeatability of cold tests appeared to be similar to the repeatability of ambient tests. tabs., figs.

  8. Impact of driving cycle and climate on electrical consumption and range of a fully electric passenger vehicle

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, N.; Belzile, M. [Transport Canada, Ottawa, ON (Canada); Christenson, M.; Edgar, J. [Environment Canada, Gatineau, PQ (Canada)

    2010-07-01

    Transport Canada's ecotechnology for vehicles (eTV) program is a $15 million program, operated over 4 years (2007-2011) that strives to encourage the introduction of advanced clean vehicle technologies in Canada. The objectives of eTV's are to reduce barriers to the introduction of clean technologies into light-duty vehicles sold in Canada. The presentation discussed the mandate of the emissions research and measurement section of Environment Canada. The dynamometer test facility, a state-of-the-art emissions testing laboratory capable of conducting comprehensive emissions measurements from a variety of sources was also discussed. Several electric mobility projects were presented. The testing rationale and testing outline were explained. It was concluded that the repeatability of cold tests appeared to be similar to the repeatability of ambient tests. tabs., figs.

  9. A role for Aurora C in the chromosomal passenger complex during human preimplantation embryo development

    NARCIS (Netherlands)

    Santos, Margarida Avo; van de Werken, Christine; de Vries, Marieke; Jahr, Holger; Vromans, Martijn J. M.; Laven, Joop S. E.; Fauser, Bart C.; Kops, Geert J.; Lens, Susanne M.; Baart, Esther B.

    BACKGROUND: Human embryos generated by IVF demonstrate a high incidence of chromosomal segregation errors during the cleavage divisions. To analyse underlying molecular mechanisms, we investigated the behaviour of the chromosomal passenger complex (CPC) in human oocytes and embryos. This important

  10. X-43 Hypersonic Vehicle Technology Development

    Science.gov (United States)

    Voland, Randall T.; Huebner, Lawrence D.; McClinton, Charles R.

    2005-01-01

    NASA recently completed two major programs in Hypersonics: Hyper-X, with the record-breaking flights of the X-43A, and the Next Generation Launch Technology (NGLT) Program. The X-43A flights, the culmination of the Hyper-X Program, were the first-ever examples of a scramjet engine propelling a hypersonic vehicle and provided unique, convincing, detailed flight data required to validate the design tools needed for design and development of future operational hypersonic airbreathing vehicles. Concurrent with Hyper-X, NASA's NGLT Program focused on technologies needed for future revolutionary launch vehicles. The NGLT was "competed" by NASA in response to the President s redirection of the agency to space exploration, after making significant progress towards maturing technologies required to enable airbreathing hypersonic launch vehicles. NGLT quantified the benefits, identified technology needs, developed airframe and propulsion technology, chartered a broad University base, and developed detailed plans to mature and validate hypersonic airbreathing technology for space access. NASA is currently in the process of defining plans for a new Hypersonic Technology Program. Details of that plan are not currently available. This paper highlights results from the successful Mach 7 and 10 flights of the X-43A, and the current state of hypersonic technology.

  11. The consequences of an increase in heavy goods vehicles for passenger car drivers' mental workload and behaviour : A simulator study

    NARCIS (Netherlands)

    De Waard, D.; Kruizinga, A; Brookhuis, K.A.

    The effects of an increase in Heavy Goods Vehicles (HGVs) on merging behaviour and on mental workload of motorists during filtering in and out of traffic were studied. Participants drove in a driving simulator in a total of 12 conditions; twice in each of two weather conditions and in three traffic

  12. 75 FR 4996 - Safety Requirements for Operators of Small Passenger-Carrying Commercial Motor Vehicles Used in...

    Science.gov (United States)

    2010-02-01

    ... vehicle for driver inspection is 11 hours [250 working days per year x ((95% no defects x 2 minutes 35... the Safe, Accountable, Flexible, Efficient Transportation Equity Act: A Legacy for Users (SAFETEA-LU... exemptions contemplated by the Conference Report or other legislative history. ``[I]n the absence of a...

  13. Development of Vehicle Model Test for Road Loading Analysis of Sedan Model

    Science.gov (United States)

    Mohd Nor, M. K.; Noordin, A.; Ruzali, M. F. S.; Hussen, M. H.

    2016-11-01

    Simple Structural Surfaces (SSS) method is offered as a means of organizing the process for rationalizing the basic vehicle body structure load paths. The application of this simplified approach is highly beneficial in the design development of modern passenger car structure especially during the conceptual stage. In Malaysia, however, there is no real physical model of SSS available to gain considerable insight and understanding into the function of each major subassembly in the whole vehicle structures. Based on this motivation, a physical model of SSS for sedan model with the corresponding model vehicle tests of bending and torsion is proposed in this work. The proposed approach is relatively easy to understand as compared to Finite Element Method (FEM). The results show that the proposed vehicle model test is capable to show that satisfactory load paths can give a sufficient structural stiffness within the vehicle structure. It is clearly observed that the global bending stiffness reduce significantly when more panels are removed from a complete SSS model. It is identified that parcel shelf is an important subassembly to sustain bending load. The results also match with the theoretical hypothesis, as the stiffness of the structure in an open section condition is shown weak when subjected to torsion load compared to bending load. The proposed approach can potentially be integrated with FEM to speed up the design process of automotive vehicle.

  14. Hydrogen hybrid vehicle engine development: Experimental program

    Energy Technology Data Exchange (ETDEWEB)

    Van Blarigan, P. [Sandia National Lab., Livermore, CA (United States)

    1995-09-01

    A hydrogen fueled engine is being developed specifically for the auxiliary power unit (APU) in a series type hybrid vehicle. Hydrogen is different from other internal combustion (IC) engine fuels, and hybrid vehicle IC engine requirements are different from those of other IC vehicle engines. Together these differences will allow a new engine design based on first principles that will maximize thermal efficiency while minimizing principal emissions. The experimental program is proceeding in four steps: (1) Demonstration of the emissions and the indicated thermal efficiency capability of a standard CLR research engine modified for higher compression ratios and hydrogen fueled operation. (2) Design and test a new combustion chamber geometry for an existing single cylinder research engine, in an attempt to improve on the baseline indicated thermal efficiency of the CLR engine. (3) Design and build, in conjunction with an industrial collaborator, a new full scale research engine designed to maximize brake thermal efficiency. Include a full complement of combustion diagnostics. (4) Incorporate all of the knowledge thus obtained in the design and fabrication, by an industrial collaborator, of the hydrogen fueled engine for the hybrid vehicle power train illustrator. Results of the CLR baseline engine testing are presented, as well as preliminary data from the new combustion chamber engine. The CLR data confirm the low NOx produced by lean operation. The preliminary indicated thermal efficiency data from the new combustion chamber design engine show an improvement relative to the CLR engine. Comparison with previous high compression engine results shows reasonable agreement.

  15. Hybrid Underwater Vehicle: ARV Design and Development

    Directory of Open Access Journals (Sweden)

    Zhigang DENG

    2014-02-01

    Full Text Available The development of SMU-I, a new autonomous & remotely-operated vehicle (ARV is described. Since it has both the characteristics of autonomous underwater vehicle (AUV and remote operated underwater vehicle (ROV, it is able to achieve precision fix station operation and manual timely intervention. In the paper the initial design of basic components, such as vehicle, propulsion, batteries etc. and the control design of motion are introduced and analyzed. ROV’s conventional cable is replaced by a fiber optic cable, which makes it available for high-bandwidth real-time video, data telemetry and high-quality teleoperation. Furthermore, with the aid of the manual real-time remote operation and ranging sonar, it also resolves the AUV’s conflicting issue, which can absolutely adapt the actual complex sea environment and satisfy the unknown mission need. The whole battery system is designed as two-battery banks, whose voltages and temperatures are monitored through CAN (controller area network bus to avoid battery fire and explosion. A fuzzy-PID controller is designed for its motion control, including depth control and direction control. The controller synthesizes the advantage of fuzzy control and PID control, utilizes the fuzzy rules to on-line tune the parameters of PID controller, and achieves a better control effect. Experiment results demonstrate to show the effectiveness of the test-bed.

  16. Development and review of Euro 5 passenger car emission factors based on experimental results over various driving cycles.

    Science.gov (United States)

    Fontaras, Georgios; Franco, Vicente; Dilara, Panagiota; Martini, Giorgio; Manfredi, Urbano

    2014-01-15

    The emissions of CO2 and regulated pollutants (NOx, HC, CO, PM) of thirteen Euro 5 compliant passenger cars (seven gasoline, six Diesel) were measured on a chassis dynamometer. The vehicles were driven repeatedly over the European type-approval driving cycle (NEDC) and the more dynamic WMTC and CADC driving cycles. Distance-specific emission factors were derived for each pollutant and sub-cycle, and these were subsequently compared to the corresponding emission factors provided by the reference European models used for vehicle emission inventory compilation (COPERT and HBEFA) and put in context with the applicable European emission limits. The measured emissions stayed below the legal emission limits when the type-approval cycle (NEDC) was used. Over the more dynamic cycles (considered more representative of real-world driving) the emissions were consistently higher but in most cases remained below the type-approval limit. The high NOx emissions of Diesel vehicles under real-world driving conditions remain the main cause for environmental concern regarding the emission profile of Euro 5 passenger cars. Measured emissions of NOx exceeded the type-approval limits (up to 5 times in extreme cases) and presented significantly increased average values (0.35 g/km for urban driving and 0.56 g/km for motorway driving). The comparison with the reference models showed good correlation in all cases, a positive finding considering the importance of these tools in emission monitoring and policy-making processes. © 2013. Published by Elsevier B.V. All rights reserved.

  17. Fuel economy of new passenger cars in Mexico: Trends from 1988 to 2008 and prospects

    International Nuclear Information System (INIS)

    Sheinbaum-Pardo, Claudia; Chávez-Baeza, Carlos

    2011-01-01

    This paper analyzes trends in fuel economy (kilometers per liter) of new passenger vehicles in Mexico over a period of 20 years from 1988 to 2008. Results show that in this period, fuel economy of the new passenger vehicle fleet, including multipurpose vehicles (a category similar to sport utility vehicles, SUVs), increased by only 6.3%. A simple Laspeyres index analysis was developed to evaluate both the impact of changes in vehicle sales structure by category and the changes in fuel economy. Results show that increased sales of heavier, multipurpose vehicles in place of subcompact and compact vehicles, impacted negatively on the fleet average fuel economy. If the structure of sales had continued in the same proportions across all categories as in 1988, fuel economy would have increased by 11.0%, instead of the actual 6.3%. This result coincides with trends in other countries. The paper also presents different scenarios of passenger car fuel economy for the year 2020, and its implications for gasoline consumption and CO 2 emissions. The results may influence the new passenger vehicle fuel economy standard that is currently under discussion in Mexico.

  18. Developing a Blended Type Course of Introduction to Hybrid Vehicles

    OpenAIRE

    Na Zhu

    2016-01-01

    An innovative course of introduction to hybrid vehicles is developed for both associate and bachelor degree programs for engineering technology with automotive/mechanical concentration. The hybrid vehicle course content includes several topics, such as the rational of pure electric vehicle and hybrid vehicle, hybrid vehicle propulsion systems, fundamentals of motor/generator systems, fundamentals of battery and energy management system, and introduction to various configurations of hybrid veh...

  19. RFB research and development in WIG vehicles

    Science.gov (United States)

    Fischer, Hanno

    An account is given of the development history of wing-in-ground (WIG) effect aircraft at a major West German aircraft manufacturer since 1964; these efforts have encompassed the development of the X113 and X114 'airfoilboat' WIG seaplanes. Attention is given to the aerodynamic efficiency and operational economy trends that result from up-scaling of WIG craft configurations to takeoff gross weights of the order of 300 tons. Also noted is the illustration of comparative efficiency among types of transportation, including WIG vehicles, given by the von Karman-Gabrielli diagram.

  20. Development of in-vehicle noise prediction models for Mumbai Metropolitan Region, India

    Directory of Open Access Journals (Sweden)

    Vishal Konbattulwar

    2016-08-01

    Full Text Available Traffic noise is one of the major sources of noise pollution in metropolitan regions causing various health hazards (e.g., long-term sleep disturbance, increase in blood pressure, physical tension, etc.. In this research, noise prediction models, which can measure the noise level experienced by the commuters while driving or traveling by motorized vehicles in the Mumbai Metropolitan Region, India, were developed. These models were developed by conducting a comprehensive study of various factors (e.g., vehicle speed, traffic volume and road characteristics, etc. affecting the levels of concentration of noise. A widespread data collection was done by conducting road trips of total length of 403.80 km via different modes of transport, such as air-conditioned (A/C car, non A/C car, bus and intermediate public transport (i.e., traditional 3-wheeler autos. Multiple regression analyses were performed to develop a functional relation between equivalent noise levels experienced by passengers while traveling (which was considered as a dependent variable and explanatory variables such as traffic characteristics, vehicle class, vehicle speed, various other location characteristics, etc. Noise levels are generally higher in the vicinity of intersections and signalized junctions. Independent data sets (for each mode of transport were used to validate the developed models. It was noted that maximum differences between observed and estimated values from the model were within the range of ±7.8% of the observed value.

  1. The Cooperative Organization And Rural Passenger Transportation: An Approach to Community Development.

    Science.gov (United States)

    Stommes, Eileen S.

    The need for passenger transportation is widely recognized by rural communities. Shrinking federal funding has led many communities and human service agencies to experiment with innovative approaches to provide transportation services. One such approach is the use of cooperative organizations to provide needed services. A study conducted by the…

  2. Fast Charging Electric Vehicle Research & Development Project

    Energy Technology Data Exchange (ETDEWEB)

    Heny, Michael

    2014-03-31

    The research and development project supported the engineering, design and implementation of on-road Electric Vehicle (“EV”) charging technologies. It included development of potential solutions for DC fast chargers (“DCFC”) capable of converting high voltage AC power to the DC power required by EVs. Additional development evaluated solutions related to the packaging of power electronic components and enclosure design, as well as for the design and evaluation of EV charging stations. Research compared different charging technologies to identify optimum applications in a municipal fleet. This project collected EV usage data and generated a report demonstrating that EVs, when supported by adequate charging infrastructure, are capable of replacing traditional internal combustion vehicles in many municipal applications. The project’s period of performance has demonstrated various methods of incorporating EVs into a municipal environment, and has identified three general categories for EV applications: Short Commute: Defined as EVs performing in limited duration, routine commutes. - Long Commute: Defined as tasks that require EVs to operate in longer daily mileage patterns. - Critical Needs: Defined as the need for EVs to be ready at every moment for indefinite periods. Together, the City of Charlottesville, VA (the “City”) and Aker Wade Power Technologies, LLC (“Aker Wade”) concluded that the EV has a viable position in many municipal fleets but with limited recommendation for use in Critical Needs applications such as Police fleets. The report also documented that, compared to internal combustion vehicles, BEVs have lower vehicle-related greenhouse gas (“GHG”) emissions and contribute to a reduction of air pollution in urban areas. The enhanced integration of EVs in a municipal fleet can result in reduced demand for imported oil and reduced municipal operating costs. The conclusions indicated in the project’s Engineering Report (see Attachment

  3. Carbon dioxide emissions from passenger transport in China since 1949: Implications for developing sustainable transport

    International Nuclear Information System (INIS)

    Loo, Becky P.Y.; Li, Linna

    2012-01-01

    This paper traces the historical evolution and spatial disparity of CO 2 emissions from passenger transport in China. The general trends of CO 2 emissions from four passenger transport modes are estimated by both the distance-based and fuel-based methods. The results suggest that CO 2 emissions from road transport represented the leading source of passenger transport CO 2 emissions in China. Moreover, they have continued to grow rapidly. Air transport was the second largest contributor since 1998. Emissions from rail and water transport have remained relatively stable with lower emission intensity. At the provincial level, great regional disparity was noticeable, especially in road transport. Moreover, the decomposition analysis shows that income growth was the principal factor leading to the growth of passenger transport CO 2 emissions in China for both the 1949–1979 and 1980–2009 periods. The second most important factor was increased transport intensity and modal shifts for the former and the latter period, respectively. The main factor contributed to emission reduction was the lower emission intensity supported by policies, although the effect was weak. In the future, more policies to encourage modal shifts toward sustainable transport modes and travel reduction should be encouraged. - Highlights: ► CO 2 emissions from passenger transport in China were estimated. ► Road transport was the largest contributor to CO 2 emission. Air transport followed. ► Factors influencing CO 2 emissions growth are analyzed by decomposition analysis. ► Income growth, higher travel intensity and modal shift were driving CO 2 emissions up. ► Policies to promote modal shifts and travel demand reduction should be encouraged.

  4. Panorama 2017 - Development of electric vehicle: where are we now?

    International Nuclear Information System (INIS)

    Ternel, Cyprien

    2016-09-01

    Electric vehicles - a term which refers to battery electric vehicles (BEV) and plug-in hybrid vehicles (PHEV) - are regarded as one way to lower energy costs and reduce the environmental impact of transport. While mild or full hybrid vehicles are gradually becoming more widespread, the market for electric vehicles is still developing. While the symbolic threshold of one million electric vehicles in circulation worldwide was surpassed in 2015 and sales are increasing from year to year, certain limitations could nevertheless hinder this growth. High purchase prices, the need to establish incentive-based public policies to significantly increase sales, and vehicle range are challenges to overcome before electric vehicles become a sustainable part of the world's automobile fleet. This memorandum takes stock of this specific market and highlights the reasons to believe in its continued progress. It mainly discusses private vehicles (including micro-cars) and utility vehicles, but a specific section is dedicated to mopeds and motorbikes

  5. Vision-based vehicle detection and tracking algorithm design

    Science.gov (United States)

    Hwang, Junyeon; Huh, Kunsoo; Lee, Donghwi

    2009-12-01

    The vision-based vehicle detection in front of an ego-vehicle is regarded as promising for driver assistance as well as for autonomous vehicle guidance. The feasibility of vehicle detection in a passenger car requires accurate and robust sensing performance. A multivehicle detection system based on stereo vision has been developed for better accuracy and robustness. This system utilizes morphological filter, feature detector, template matching, and epipolar constraint techniques in order to detect the corresponding pairs of vehicles. After the initial detection, the system executes the tracking algorithm for the vehicles. The proposed system can detect front vehicles such as the leading vehicle and side-lane vehicles. The position parameters of the vehicles located in front are obtained based on the detection information. The proposed vehicle detection system is implemented on a passenger car, and its performance is verified experimentally.

  6. Factors related to seatbelt-wearing among rear-seat passengers in Malaysia.

    Science.gov (United States)

    Ng, Choy Peng; Law, Teik Hua; Wong, Shaw Voon; Kulanthayan, S

    2013-01-01

    The benefit of wearing a rear seatbelt in reducing the risk of motor vehicle crash-related fatalities and injuries has been well documented in previous studies. Wearing a seatbelt not only reduces the risk of injury to rear-seat passengers, but also reduces the risk of injury to front-seat occupant who could be crushed by unbelted rear-seat passengers in a motor vehicle crash. Despite the benefits of wearing a rear seatbelt, its rate of use in Malaysia is generally low. The objective of this study was to identify factors that are associated with the wearing of a seatbelt among rear-seat passengers in Malaysia. Multinomial logistic regression analysis of the results of a questionnaire survey of 1651 rear-seat passengers revealed that rear-seat passengers who were younger, male, single and less educated and who had a perception of a low level of legislation enforcement, a lower risk-aversion and less driving experience (only for passengers who are also drivers) were less likely to wear a rear seatbelt. There was also a significant positive correlation between driver seatbelt and rear seatbelt-wearing behaviour. This implies that, in regards to seatbelt-wearing behaviour, drivers are more likely to adopt the same seatbelt-wearing behaviour when travelling as rear-seat passengers as they do when driving. These findings are crucial to the development of new interventions to increase the compliance rate of wearing a rear seatbelt. Copyright © 2012 Elsevier Ltd. All rights reserved.

  7. Development of an Autonomous Navigation Technology Test Vehicle

    National Research Council Canada - National Science Library

    Tobler, Chad K

    2004-01-01

    .... In order to continue these research activities at CIMAR, a new Kawasaki Mule All-Terrain Vehicle was chosen to be automated as a test-bed for the purpose of developing and testing autonomous vehicle technologies...

  8. The consequences of an increase in heavy goods vehicles for passenger car drivers' mental workload and behaviour: a simulator study.

    Science.gov (United States)

    de Waard, Dick; Kruizinga, Anje; Brookhuis, Karel A

    2008-03-01

    The effects of an increase in Heavy Goods Vehicles (HGVs) on merging behaviour and on mental workload of motorists during filtering in and out of traffic were studied. Participants drove in a driving simulator in a total of 12 conditions; twice in each of two weather conditions and in three traffic conditions. The weather conditions were clear weather and foggy weather. The traffic conditions were without HGVs (i.e. only private cars), the current mix of HGVs and private cars, and a condition with a 70% increase of HGVs leading to an HGV column in the slow lane. The focus of the study was on assessing effects on behaviour and mental workload during filtering into traffic, and during exiting from the motorway. During the experiment driving performance was registered, behaviour was observed, self reports were collected, and the participant's heart rate was recorded. The results showed that directly after filtering into traffic the variation in driving speed increased and the minimum time headway decreased with an increase in the proportion of HGVs. Joining motorway traffic was considered to involve greater effort and risk in the condition with a column of HGVs. The effects of the conditions on heart rate are less clear, although the moment when the participants joined the traffic is clearly visible. The effects of weather conditions were limited, drivers adapting their driving behaviour in adverse weather by reducing speed. To exit the motorway is not a difficult manoeuvre. For that reason the lane change from the left hand to the right hand lane that preceded the exit was analysed. Although increased mental effort was reported and the lane change was visible in the heart rate record, no critical changes as a result of increase in proportion of HGVs were found for this manoeuvre. However, in the condition with a column of HGVs, the exit that had to be taken was most frequently missed as HGVs obstructed the view of the exit signs. It is concluded that an increase in

  9. Developing pathways to low carbon land-based passenger transport in Great Britain by 2050

    International Nuclear Information System (INIS)

    Bristow, Abigail L.; Tight, Miles; Pridmore, Alison; May, Anthony D.

    2008-01-01

    The key aim of this paper is to examine strategic pathways to low carbon personal transport in Britain and to compare these with the current trajectory of transport policy. A 2050 baseline was established using trend information, forecasts and best evidence from the literature on response to policy intervention. A range of strategies are tested including: technological development, pricing, public transport and soft measures. We conclude that even dramatic technological advance cannot meet the more stringent targets for carbon reduction in the absence of considerable behavioural change. The most promising combinations of measures involve clear price signals to encourage both a reduction in the use of motorised transport and the development and purchase of more efficient vehicles; decarbonisation of public transport and facilitating measures to enhance access whilst reducing the need for motorised travel

  10. Electric and Hybrid Vehicle System Research and Development Project: Hybrid Vehicle Potential Assessment. Volume VI. Cost analysis

    Energy Technology Data Exchange (ETDEWEB)

    Hardy, K.S.

    1979-09-30

    The purpose of the cost analysis is to determine the economic feasibility of a variety of hybrid vehicles with respect to conventional vehicles specifically designed for the same duty cycle defined by the mission analysis. Several different hybrid configurations including parallel, parallel-flywheel, and series vehicles were evaluated. The ramifications of incorporating examples of advanced batteries, these being the advanced lead-acid, nickel-zinc, and sodium sulfur were also investigated. Vehicles were specifically designed with these batteries and for the driving cycles specified by the mission. Simulated operation on the missions yielded the energy consumption (petroleum and/or electricity) over the driving cycles. It was concluded that: in the event that gasoline prices reach $2.50 to $3.00/gal, hybrid vehicles in many applications will become economically competitive with conventional vehicles without subsidization; in some commercial applications hybrid vehicles could be economically competitive, when the gasoline price ranges from $1.20 to $1.50/gal. The cost per kWh per cycle of the advanced batteries is much more important economically than the specific energy; the series hybrid vehicles were found to be more expensive in comparison to the parallel or parallel-flywheel hybrids when designed as passenger vehicles; and hybrid vehicles designed for private use could become economically competitive and displace up to 50% of the fuel normally used on that mission if subsidies of $500 to $2000 were supplied to the owner/operator. (LCL)

  11. Airline Passengers

    OpenAIRE

    Wittmer, Andreas; Hinnen, Gieri

    2016-01-01

    Airlines create value for employees, investors, governments, customers and consumers. This chapter focuses on the customers and consumers of the airline product. Airline customers, who include passengers and corporate travel providers, exert considerable market power in the air transport industry through their purchasing decisions and travel behaviour. As a purchaser of a commercial aviation product, customers are responsible for stimulating product and service innovation and their behaviour ...

  12. Frontier battery development for hybrid vehicles

    OpenAIRE

    Lewis, Heather; Park, Haram; Paolini, Maion

    2012-01-01

    Abstract Background Interest in hybrid-electric vehicles (HEVs) has recently spiked, partly due to an increasingly negative view toward the U.S. foreign oil dependency and environmental concerns. Though HEVs are becoming more common, they have a significant price premium over gasoline-powered vehicles. One of the primary drivers of this “hybrid premium” is the cost of the vehicles’ batteries. This paper focuses on these batteries used in hybrid vehicles, examines the types of batteries used f...

  13. Analysis of Passenger Car Emission Factors in RDE Tests

    Directory of Open Access Journals (Sweden)

    Pielecha Jacek

    2016-01-01

    Full Text Available The article presents a study on emission measurements in passenger cars in tests conducted under real traffic conditions – Real Driving Emissions using a Portable Emission Measurement System type of equipment. A special feature of the outlined RDE tests is that they were performed in Polish road conditions, and thus their parameters may differ from their counterparts adopted in most European Union countries. Based on the findings vehicle emission conformity factors were developed, characterized as the fractional increase (or decrease of traffic emissions during the homologation test or under normal operation conditions in relation to the emission limit standards (for chosen emission class of the vehicle. Conducted research and the calculated conformity factors allowed for the environmental impact assessment of the vehicles of various emission classes, while also allowing early actions to restrict the emissions of selected components in passenger vehicles. The methods and measures used can also be applied to other types of vehicles (e.g. heavy duty or off-road vehicles or vehicles powered by other fuels.

  14. Policies and Predictions for a Low-Carbon Transition by 2050 in Passenger Vehicles in East Asia: Based on an Analysis Using the E3ME-FTT Model

    Directory of Open Access Journals (Sweden)

    Aileen Lam

    2018-05-01

    Full Text Available In this paper we apply a model of technological diffusion, Future Technology Transformations in the Transport Sector (FTT: Transport, linked to the E3ME macroeconomic model, to study possible future technological transitions in personal passenger transport in four East Asian countries. We assess how targeted policies could impact on these transitions by defining four scenarios based on policies that aim to reduce emissions from transport. For each country we find that an integrated approach of tax incentives, subsidies, regulations (fuel economy efficiency, kick-start programs and biofuel programs yield the most significant emission reductions because, when combined, they accelerate effectively the diffusion of electric vehicles in the region.

  15. Development of Fuzzy Logic Control for Vehicle Air Conditioning System

    Directory of Open Access Journals (Sweden)

    Henry Nasution

    2008-08-01

    Full Text Available A vehicle air conditioning system is experimentally investigated. Measurements were taken during the experimental period at a time interval of one minute for a set point temperature of 22, 23 and 24oC with internal heat loads of 0, 1 and 2 kW. The cabin temperature and the speed of the compressor were varied and the performance of the system, energy consumption and energy saving ware analyzed. The main objective of the experimental work is to evaluate the energy saving obtained when the fuzzy logic control (FLC algorithm, through an inverter, continuously regulates the compressor speed. It demonstrates better control of the compressor operation in terms of energy consumption as compared to the control by using a thermostat imposing On/Off cycles on the compressor at the nominal frequency of 50 Hz. The experimental set-up consists of original components from the air conditioning system of a compact passenger vehicle. The experimental results indicate that the proposed technique can save energy and improve indoor comfort significantly for vehicle air conditioning systems compared to the conventional (On/Off control technique.

  16. Integrating passenger and freight transportation : model formulation and insights

    NARCIS (Netherlands)

    Ghilas, V.; Demir, E.; Woensel, van T.

    2013-01-01

    Integrating passenger and freight ows creates attractive business opportunities because the same transportation needs can be met with fewer vehicles and emissions. This paper seeks an integrated solution for the transportation of passenger and freight simultaneously, so that fewer vehicles are

  17. Intermodal Passenger Connectivity Database -

    Data.gov (United States)

    Department of Transportation — The Intermodal Passenger Connectivity Database (IPCD) is a nationwide data table of passenger transportation terminals, with data on the availability of connections...

  18. Research and development of electric vehicles for clean transportation.

    Science.gov (United States)

    Wada, Masayoshi

    2009-01-01

    This article presents the research and development of an electric vehicle (EV) in Department of Human-Robotics Saitama Institute of Technology, Japan. Electric mobile systems developed in our laboratory include a converted electric automobile, electric wheelchair and personal mobile robot. These mobile systems contribute to realize clean transportation since energy sources and devices from all vehicles, i.e., batteries and electric motors, does not deteriorate the environment. To drive motors for vehicle traveling, robotic technologies were applied.

  19. Sustainable development of new energy vehicle industry in China

    Science.gov (United States)

    Li, Mingyang; Li, Lingzhi

    2018-03-01

    The new energy vehicle industry in China has developed rapidly in recent years, but there is still a gap in core technology. Some problems are brought the adverse effect on it, such as imperfect infrastructures, imperfect systems in market access and regulatory, single channels for marketing and low acceptance among consumer. Based on the development of new energy vehicle industry home and abroad, this paper puts forward some problems of new energy vehicles industry in China, then offers some feasible suggestions.

  20. Developing Policy for Urban Autonomous Vehicles: Impact on Congestion

    Directory of Open Access Journals (Sweden)

    David Metz

    2018-04-01

    Full Text Available An important problem for surface transport is road traffic congestion, which is ubiquitous and difficult to mitigate. Accordingly, a question for policymakers is the possible impact on congestion of autonomous vehicles. It seems likely that the main impact of vehicle automation will not be seen until driverless vehicles are sufficiently safe for use amid general traffic on urban streets. Shared use driverless vehicles could reduce the cost of taxis and a wider range of public transport vehicles could be economic. Individually owned autonomous vehicles would have the ability to travel unoccupied and may need to be regulated where this might add to congestion. It is possible that autonomous vehicles could provide mobility services at lower cost and wider scope, such that private car use in urban areas could decline and congestion reduce. City authorities should be alert to these possibilities in developing transport policy.

  1. Current State of Military Hybrid Vehicle Development

    Science.gov (United States)

    2011-08-31

    Integrated starter generator for engine shut down, regenerative braking and avoidance of inefficient engine operation [28]. FMTV VI Composite 6-9% Fuel...and eliminating the inefficiencies associated with idling, vehicle braking and low engine speed part load efficiency, many improvements could be...different drive cycles were being used to evaluate vehicle performance. These cycles can be divided into the following two categories : (1) Time

  2. 75 FR 22317 - Federal Motor Vehicle Safety Standards; Small Business Impacts of Motor Vehicle Safety

    Science.gov (United States)

    2010-04-28

    ... 1300 [Docket No. NHTSA-2010-0054] Federal Motor Vehicle Safety Standards; Small Business Impacts of Motor Vehicle Safety AGENCY: National Highway Traffic Safety Administration (NHTSA), Department of..., multipurpose passenger vehicles, trucks, buses, trailers, incomplete vehicles, motorcycles, and motor vehicle...

  3. "Good Passengers and Not Good Passengers:" Adolescent Drivers' Perceptions About Inattention and Peer Passengers.

    Science.gov (United States)

    McDonald, Catherine C; Sommers, Marilyn S

    The purpose of this qualitative focus group elicitation research study was to explore teen driver perceptions of peer passengers and driver inattention. We utilized focus groups for data collection and content analysis to analyze the data, both of which were guided by the theory of planned behavior. We conducted 7 focus groups with 30 teens, ages 16-18, licensed for ≤1year to examine attitudes, perceived behavioral control, and norms related to driving inattention and peer passengers. The sample was 50% male, mean age 17.39 (SD 0.52) with mean length of licensure 173.7days (SD 109.2). Three themes emerged: 1) "Good and not good" passengers; 2) Passengers and technology as harmful and helpful; and 3) The driver is in charge. While passengers can be a source of distraction, our participants also identified passenger behaviors that reduced risk, such as assistance with technology and guidance for directions. An understanding of teens' perceptions of peer passengers can contribute to the development of effective interventions targeting teen driver inattention. Nurses are well-positioned to contribute to these teen crash prevention efforts. Copyright © 2016 Elsevier Inc. All rights reserved.

  4. Development of an Autonomous Vehicle for Weed and Crop Registration

    DEFF Research Database (Denmark)

    Pedersen, Tom Søndergaard; Nielsen, Kirsten Mølgaard; Andersen, Palle

    the free height of the vehicle being developed in this work has been set to 0.5 m. The size and weight of the vehicle implies a power consumption of max 1.5 kW making electrical motors suitable for propulsion and steering. To make the operation affordable the vehicle should be unmanned requiring a high......The extension of information technology and computers on farming tools results in new possibilities for crop/weed handling. In this paper a system using an autonomous field robot (vehicle) able to make images in the field is described. In the recent farming has come to rely on intensive use...... communication system between the two. The base station is the main interface to the farmer. Based on farmer information a route plan for data collection is created in the base station and send to the vehicle. The vehicle collects field data using two cameras one determinates the total weed pressure and one...

  5. Parents as passengers during pediatric transport.

    Science.gov (United States)

    Lewis, M M; Holditch-Davis, D; Brunssen, S

    1997-01-01

    The transport environment presents a unique setting in which the feasibility, advantages, and disadvantages of passengers accompanying a patient must be assessed carefully. The purpose of this study was to describe the current practice of including parents as passengers during pediatric interfacility transport. One-hundred-eighty-eight critical care transport programs in the United States responded to a voluntary mail survey, providing information about current policies, practices, and crew perceptions of the advantages and disadvantages of carrying parents as passengers. Extra seating for passengers was available in 96% of ambulances, 86% of fixed-wing aircraft, and 54% of helicopters used for pediatric transport. Parents traveled as passengers in all types of vehicles; most frequently in ambulances and fixed-wing aircraft. Twenty percent of helicopter programs allowed parent passengers on more than half of their pediatric transports in this vehicle. Advantages of parent passengers included emotional benefit for the parent and child, availability of parents for history and consent, good public relations, and having the parent present if the child dies. Disadvantages included potential parent anxiety, crew distraction, and space limitations. This study reflects the widely diverse policies, practices, and opinions relevant to this topic and confirms a need for further study.

  6. Noise and vibration reduction technology in hybrid vehicle development; Hybrid sha kaihatsu ni okeru shindo soon teigen gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshioa, T.; Sugita, H. [Toyota Motor Corp., Aichi (Japan)

    2000-03-01

    Accomplishing both environmental protection and good NVH performance has become a significant task in automotive development The first-in-the-world hybrid passenger car of mass production. 'Prius', has achieved superior NV performance compared with conventional vehicles with a 1.5-liter engine along with 50% reduction of fuel consumption and CO{sub 2} emissions. low HC, CO and NO{sub x} emissions. This paper describes NV reduction technology for solving problems peculiar to the hybrid vehicle such as engine start/stop vibration, drone noise at low engine speed and motor/generator noise and vibration. It also mentions application technology of low rolling resistance tires with light weight wheels and recycled material for sound proofing. (author)

  7. Development of hybrid system for mass productive passenger car; Joyoshayo ryosangata hybrid system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Abe, S; Sasaki, S; Matsui, H; Kubo, K [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    The Toyota Hybrid System has two power sources which engage depending on driving conditions. An improved efficiency gasoline engine provides the main power to drive the wheels, as in conventional automobiles. Drive power can also be supplied by an electric motor, which derives its electricity from a battery and a Generator. Fuel efficiency is further boosted by other measures, such as automatically cutting the engine when the vehicle is at a stop and regenerating the energy accumulate during deceleration. Compared with conventional vehicles with a 1.5-liter engine running in 10 {center_dot} 15 mode, the CO2 emissions are reduced by half. Moreover, with the use of a motor to reduce engine load during acceleration, HC, CO, and NOx emissions are cut significantly low levels. 13 figs.

  8. Workshop Protocol 5.1 “Developing infrastructure for electric passenger-cars in the corridor between Southern Scandinavia and Germany”

    DEFF Research Database (Denmark)

    Guasco, Clement Nicolas

    and academic institutions. A strategy for the development of infrastructure for electric passenger-cars in the corridor was formed using the “Future Creating” methodology. The workshop was part of the SCANDRIA Action Programme and pointed towards ways for e-mobility in the region. The workshop also provided...

  9. Tyre influences on untripped vehicle rollover

    NARCIS (Netherlands)

    Jansen, S.T.H.; Lupker, H.A.; Koppenaal, C.J.P.

    2002-01-01

    Vehicle rollover can be initiated by steering actions that occur at vehicle evasive manoeuvres or high speed cornering of commercial vehicles. This untripped vehicle rollover is more difficult to reproduce for passenger cars then for commercial vehicles. For passenger cars it occurs closer to the

  10. Current State of Military Hybrid Vehicle Development

    Science.gov (United States)

    2011-01-01

    programme were: • EP-50 parallel hybrid light armoured vehicle (LAV-III) and a refuse hauler • advanced hybrid electric drive (AHED) 8 × 8, 20 ton...herein do not necessarily state or reflect those of the US Government or the DoA, and shall not be used for advertising or product endorsement purposes. 2 Unclassified. Distribution Statement A. Approved for public release.

  11. Influence of Unsteady Aerodynamics on Driving Dynamics of Passenger Cars

    OpenAIRE

    Huemer, J.; Stickel, T.; Sagan, E.; Schwarz, M.; Wall, W.A.

    2015-01-01

    Recent approaches towards numerical investigations with CFD-Methods on unsteady aerodynamic loads of passenger cars identified major differences compared to steady state aerodynamic excitations. Furthermore innovative vehicle concepts like electric-vehicles or hybrid drives further challenge the basic layout of passenger cars. Therefore the relevance of unsteady aerodynamic loads on cross-wind stability of changing basic vehicle architectures should be analysed. In order to assure and improve...

  12. Developing a Blended Type Course of Introduction to Hybrid Vehicles

    Directory of Open Access Journals (Sweden)

    Na Zhu

    2016-02-01

    Full Text Available An innovative course of introduction to hybrid vehicles is developed for both associate and bachelor degree programs for engineering technology with automotive/mechanical concentration. The hybrid vehicle course content includes several topics, such as the rational of pure electric vehicle and hybrid vehicle, hybrid vehicle propulsion systems, fundamentals of motor/generator systems, fundamentals of battery and energy management system, and introduction to various configurations of hybrid vehicle systems available in market and under development. Hybrid vehicle technology is a new area and developed rapidly in the field of automotive and mechanical engineering. Students need not only the fundamentals and concepts from college, but also the ability to keep up with the latest technology after their graduation. Therefore, a blended course type is employed to help students have a better understanding of the fundamentals of hybrid vehicle and developing their self-studying ability. Topics in the course have three steps of learning. Firstly, on-ground lecture is given in class, where the instructor explains basic knowledge, such as principles, equations, and design rules.  In this way, the students will have enough background knowledge and be able to conduct further self-reading and research work. Secondly, students are required to go to university’s desire to learn (D2L online system and finish the online part of the topic. In the D2L system, students will find a quiz and its supporting materials. Thirdly, students come back to the on-ground lecture and discuss the quiz in groups with instructor. After the discussion, the instructor gives students a conclusion of the topic and moves forward to the next topic. A computer simulation class is also given to help student better understand the operation strategies of the hybrid vehicle systems and have a trial of design of hybrid vehicle.

  13. Development of electrostatic charging evaluation equipment for automobile seat; Jidoshayo seat no taidensei shiken hyoka sochi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, K [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    When passengers get out of vehicle, electrostatics is generated by separation of seat cloth and passenger cloth, and then charged to passenger`s body. It has been impossible for us to simulate this induction charging phenomenon with current evaluation equipments. We developed a new seat cloth evaluation equipments using induction charging plate, which enables us to simulate the phenomenon. This paper describes this new electrostatic charging evaluation method for automobile seat cloth. 5 refs., 6 figs.

  14. Initial investigation into development of accelerated pavement evaluation (APE) vehicle

    CSIR Research Space (South Africa)

    Steyn, WJvdM

    2002-08-01

    Full Text Available n e n t d e f o r m a t i o n [ m m ] Test 1 Test 2 Test 3 Test 4 Initial indication of performance Indication of performance after traffic application TR-2003/9: Initial investigation into development of APE vehicle. 6 2... Restricted Contract Report Initial Investigation into Development of Accelerated Pavement Evaluation (APE) Vehicle. Author: WJvdM Steyn M de Beer PREPARED FOR: PREPARED BY: CSIR Transportek STEP CSIR Transportek PO...

  15. Development of the Hawk/Nike Hawk sounding rocket vehicles

    Science.gov (United States)

    Flowers, B. J.

    1976-01-01

    A new sounding rocket family, the Hawk and Nike-Hawk Vehicles, have been developed, flight tested and added to the NASA Sounding Rocket Vehicle Stable. The Hawk is a single-stage vehicle that will carry 35.6 cm diameter payloads weighing 45.5 kg to 91 kg to altitudes of 78 km to 56 km, respectively. The two-stage Nike-Hawk will carry payloads weighing 68 kg to 136 kg to altitudes of 118 km to 113 km, respectively. Both vehicles utilize the XM22E8 Hawk rocket motor which is available in large numbers as a surplus item from the U.S. Army. The Hawk fin and tail can hardware were designed in-house. The Nike tail can and fin hardware are surplus Nike-Ajax booster hardware. Development objectives were to provide a vehicle family with a larger diameter, larger volume payload capability than the Nike-Apache and Nike-Tomahawk vehicles at comparable cost. Both vehicles performed nominally in flight tests.

  16. Greenhouse Emission Reductions and Natural Gas Vehicles: A Resource Guide on Technology Options and Project Development

    Energy Technology Data Exchange (ETDEWEB)

    Orestes Anastasia; NAncy Checklick; Vivianne Couts; Julie Doherty; Jette Findsen; Laura Gehlin; Josh Radoff

    2002-09-01

    that deal with passenger vehicles--and with transportation in general--do not address the climate change component explicitly, and thus there are few GHG reduction goals that are included in these programs. Furthermore, there are relatively few protocols that exist for accounting for the GHG emissions reductions that arise from transportation and, specifically, passenger vehicle projects and programs. These accounting procedures and principles gain increased importance when a project developer wishes to document in a credible manner, the GHG reductions that are achieved by a given project or program. Section four of this paper outlined the GHG emissions associated with NGVs, both upstream and downstream, and section five illustrated the methodology, via hypothetical case studies, for measuring these reductions using different types of baselines. Unlike stationary energy combustion, GHG emissions from transportation activities, including NGV projects, come from dispersed sources creating a need for different methodologies for assessing GHG impacts. This resource guide has outlined the necessary context and background for those parties wishing to evaluate projects and develop programs, policies, projects, and legislation aimed at the promotion of NGVs for GHG emission reduction.

  17. Hypersonic Vehicle Propulsion System Simplified Model Development

    Science.gov (United States)

    Stueber, Thomas J.; Raitano, Paul; Le, Dzu K.; Ouzts, Peter

    2007-01-01

    This document addresses the modeling task plan for the hypersonic GN&C GRC team members. The overall propulsion system modeling task plan is a multi-step process and the task plan identified in this document addresses the first steps (short term modeling goals). The procedures and tools produced from this effort will be useful for creating simplified dynamic models applicable to a hypersonic vehicle propulsion system. The document continues with the GRC short term modeling goal. Next, a general description of the desired simplified model is presented along with simulations that are available to varying degrees. The simulations may be available in electronic form (FORTRAN, CFD, MatLab,...) or in paper form in published documents. Finally, roadmaps outlining possible avenues towards realizing simplified model are presented.

  18. Passengers, Information, and Disruptions

    NARCIS (Netherlands)

    E. van der Hurk (Evelien)

    2015-01-01

    markdownabstract__Abstract__ Passengers traveling in public transport generate a detailed digital track record of their journey through using automated fare collection systems and carrying mobile devices. This information on passenger behavior has only recently become available to public

  19. Analyzing the Effect of Passenger-Requested Unscheduled Stops on Demand

    Directory of Open Access Journals (Sweden)

    Dejan Paliska

    2007-07-01

    Full Text Available This paper discusses the effect of unscheduled stops requestedby passengers on bus transit demand and presents theresults of its study. In the research a set of regression modelsthat estimate the route-level demand were developed using datacollected with Automatic Passenger Counters and AutomaticVehicle Location systems installed on buses, and demographic,socio-economic and land use information from other sources.The results obtained indicate that the number of rider-requestedunscheduled stops have no significant effect on demand,suggesting that the company policy which tolerates unscheduledstops is inadequate for attracting new riders.

  20. The perspectives of development of natural gas for vehicles

    International Nuclear Information System (INIS)

    Anon.

    1996-01-01

    This short paper analyses the actions carried out in the world, and in particular in France, to develop and promote the use of natural gas for vehicles (NGV). In France, a protocol of agreement was signed in June 1994 between the French car manufacturers, Gaz de France and the French Association of Natural Gas for Vehicles (AFGNV) in order to develop new kinds of gas fueled vehicles, more optimized engines, to increase the number of gas distribution stations, to ratify the new models of vehicles and the specific parts for these vehicles (composite materials tanks), to carry out R and D work on gas compressors, and to develop public and private fleets of urban buses and public service vehicles. The forthcoming application of the 'Clean Air Law' will support these actions. Significant and similar developments take place also in more than 30 other countries under the same environmental motivation and ambitious programs are planned in the USA, Japan and Argentina for the year 2000. The R and D effort now focusses on the use of LNG instead of compressed natural gas. (J.S.)

  1. Design and development of a walking robotic vehicle

    International Nuclear Information System (INIS)

    Shkolnik, N.

    1990-01-01

    Quest Systems, Inc., sponsored by DARPA, is developing a low-cost, high-efficiency walking robotic vehicle (WRV). This vehicle will be targeted for a variety of applications in waste management, hazardous materials transport and handling, nuclear plant operations, maintenance and decontamination, security, mining, and other areas in industrial and military sectors. The purpose of the development is twofold. The first goal is to demonstrate that, in spite of common beliefs, legged locomotion can be as efficient as wheeled (at low velocities), which could make a walking vehicle a prime candidate for an autonomously operated platform. The second goal is to show that this type of vehicle can be built rather inexpensively (below $100,000), which would allow it to compete on a cost/functionality basis with wheeled and tracked ones

  2. Benefits of Government Incentives for Reusable Launch Vehicle Development

    Science.gov (United States)

    Shaw, Eric J.; Hamaker, Joseph W.; Prince, Frank A.

    1998-01-01

    Many exciting new opportunities in space, both government missions and business ventures, could be realized by a reduction in launch prices. Reusable launch vehicle (RLV) designs have the potential to lower launch costs dramatically from those of today's expendable and partially-expendable vehicles. Unfortunately, governments must budget to support existing launch capability, and so lack the resources necessary to completely fund development of new reusable systems. In addition, the new commercial space markets are too immature and uncertain to motivate the launch industry to undertake a project of this magnitude and risk. Low-cost launch vehicles will not be developed without a mature market to service; however, launch prices must be reduced in order for a commercial launch market to mature. This paper estimates and discusses the various benefits that may be reaped from government incentives for a commercial reusable launch vehicle program.

  3. Analyzing injury severity of bus passengers with different movements.

    Science.gov (United States)

    Li, Duo; Zhao, Yifei; Bai, Qiang; Zhou, Bei; Ling, Hongbiao

    2017-07-04

    Though public transport vehicles are rarely involved in mass casualty accidents, when they are, the number of injuries and fatalities is usually high due to the high passenger capacity. Of the few studies that have been conducted on bus safety, the majority focused on vehicle safety features, road environmental factors, as well as driver characteristics. Nevertheless, few studies have attempted to investigate the underlying risk factors related to bus occupants. This article presents an investigation aimed at identifying the risk factors affecting injury severity of bus passengers with different movements. Three different passenger movement types including standing, seated, and boarding/alighting were analyzed individually using classification and regression tree (CART) method based on publicly available accident database of Great Britain. According to the results of exploratory analyses, passenger age and vehicle maneuver are associated with passenger injury severity in all 3 types of accidents. Moreover, the variable "skidding and overturning" is associated with injury severity of seated passengers and driver age is correlated with injury severity of standing and boarding/alighting passengers. The CART method shows its ability to identify and easily explain the complicated patterns affecting passenger injury severity. Several countermeasures to reduce bus passenger injury severity are recommended.

  4. Fiscal 1998 achievement report. Research and development of advanced clean energy vehicles; 1998 nendo kokoritsu clean energy jidosha no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The efforts aim to develop advanced clean energy vehicles (ACEVs) which drive on substitutes of oil low in pollution, consuming 1/2 or less energy and emitting 1/2 or less CO2 than the existing vehicles. Studies conducted in fiscal 1998 covered high-efficiency hybrid power systems and ACEVs. Efforts to develop ACEVs involved a reformed methanol fuel cell hybrid passenger car of Nissan Motor Co., Ltd. (improvement on element technologies, study of methanol concentration); CNG (compressed natural gas) engine hybrid passenger car of Honda Research and Development Co., Ltd. (improvement on flywheels, studies of ANG (adsorbent natural gas) adsorbent and ANG tank); CNG ceramics engine hybrid cargo truck of Isuzu Ceramics Research Institute Co., Ltd. (fabrication of ceramics single-cylinder engine, design and fabrication of vehicle control system, fabrication of prototype); CNG lean burn engine hybrid cargo truck of Mitsubishi Motors Co., Ltd. (studies, designing, and fabrication of engine element parts); LNG engine hybrid bus of Nissan Diesel Motor Co., Ltd. (development of engine and power storage); and DME (dimethylether) engine hybrid bus of Hino Motors, Ltd. (development of DME fuel injection system and high-efficiency power storage). (NEDO)

  5. Development & optimization of a rule-based energy management strategy for fuel economy improvement in hybrid electric vehicles

    Science.gov (United States)

    Asfoor, Mostafa

    The gradual decline of oil reserves and the increasing demand for energy over the past decades has resulted in automotive manufacturers seeking alternative solutions to reduce the dependency on fossil-based fuels for transportation. A viable technology that enables significant improvements in the overall energy conversion efficiencies is the hybridization of conventional vehicle drive systems. This dissertation builds on prior hybrid powertrain development at the University of Idaho. Advanced vehicle models of a passenger car with a conventional powertrain and three different hybrid powertrain layouts were created using GT-Suite. These different powertrain models were validated against a variety of standard driving cycles. The overall fuel economy, energy consumption, and losses were monitored, and a comprehensive energy analysis was performed to compare energy sources and sinks. The GT-Suite model was then used to predict the formula hybrid SAE vehicle performance. Inputs to this model were a numerically predicted engine performance map, an electric motor torque curve, vehicle geometry, and road load parameters derived from a roll-down test. In this case study, the vehicle had a supervisory controller that followed a rule-based energy management strategy to insure a proper power split during hybrid mode operation. The supervisory controller parameters were optimized using discrete grid optimization method that minimized the total amount of fuel consumed during a specific urban driving cycle with an average speed of approximately 30 [mph]. More than a 15% increase in fuel economy was achieved by adding supervisory control and managing power split. The vehicle configuration without the supervisory controller displayed a fuel economy of 25 [mpg]. With the supervisory controller this rose to 29 [mpg]. Wider applications of this research include hybrid vehicle controller designs that can extend the range and survivability of military combat platforms. Furthermore, the

  6. Passenger and Cell Phone Conversations in Simulated Driving

    Science.gov (United States)

    Drews, Frank A.; Pasupathi, Monisha; Strayer, David L.

    2008-01-01

    This study examines how conversing with passengers in a vehicle differs from conversing on a cell phone while driving. We compared how well drivers were able to deal with the demands of driving when conversing on a cell phone, conversing with a passenger, and when driving without any distraction. In the conversation conditions, participants were…

  7. Development of an Autonomous Vehicle for Weed and Crop Registration

    DEFF Research Database (Denmark)

    Pedersen, Tom Søndergaard; Nielsen, Kirsten Mølgaard; Andersen, Palle

    The extension of information technology and computers on farming tools results in new possibilities for crop/weed handling. In this paper a system using an autonomous field robot (vehicle) able to make images in the field is described. In the recent farming has come to rely on intensive use...... degree of autonomy. The vehicle is part of an autonomous information system for crop and weed registration in fields which is developed at Aalborg University and The Danish Institute of Agricultural Science. The system consists of the vehicle and a stationary base station as well as a wireless...... be a solution but at present the image analysis technology does not have the capability for online analysis. An alternative way is to construct a weed map prior to the spraying. In order to avoid damage to the soil a light weight vehicle carrying a camera is an obvious choice. To minimize damage to the crop...

  8. Strategic alliances for the development of fuel cell vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Maruo, Kanehira [Goeteborg Univ. (Sweden). Section of Science and Technology Studies

    1998-12-01

    The aim of this paper is to explore and describe the current stage of fuel cell vehicle development in the world. One can write three possible future scenarios - an optimistic, a realistic, and a pessimistic scenario: - The optimistic scenario -- The Daimler/Ballard/Ford alliance continues to develop fuel cell stacks and fuel cell vehicle systems as eagerly as they have been doing in recent years. Daimler(/Chrysler)-Benz continues to present its Necar 4, Necar 5, and so on, as planned, and thus keeps Toyota and Honda under severe pressure. Toyota`s and Honda`s real motivation seems to be not to allow Daimler-Benz to be the first to market. Their investment in fuel cell technology will be very large. At the same time, governments and other stake-holders will quickly and in a timely fashion build up infrastructures. We will then see many fuel cell vehicles by 2004. A paradigm shift in automotive technology will have taken place. - The realistic scenario -- Fuel cell vehicles will reach the same level of development by 2004/2005 as pure electric vehicles were at in 1997/1998. This means that fuel cell vehicles will be produced at the rate of several hundred vehicles per year per manufacturer and cost about $40,000 or more, which is still considerably more expensive than ordinary gasoline cars. These fuel cell vehicles will have a performance similar to today`s advanced electric vehicles, e.g., Toyota`s RAV4/EV and Honda`s EV Plus. To go further from this stage to the mass-production stage strong government incentives will be needed. - The pessimistic scenario -- It turns out that fuel cells are not as pure or efficient as in theory and in laboratory experiments. Prices of gasoline and diesel gas continue to be very low. The Californian 10% ZEV Requirement that has been meant to be valid at least ten years from 2003 through 2012 will be suspended or greatly modified. Daimler-Benz, Toyota, and Honda slow down their fuel cell vehicle development activities. No one is

  9. 78 FR 51812 - Urbanized Area Formula Grants; Passenger Ferry Grant Program

    Science.gov (United States)

    2013-08-21

    ... authorized by the Moving Ahead for Progress in the 21st Century Act (MAP-21), Public Law 112- 141, July 6... accommodate walk-on passengers. 2. Eligible Projects Under this competitive program, eligible projects are... the number of trips (passengers and vehicles), the number of walk-on passengers, and transfers to...

  10. Development of superconducting magnets for the Canadian electrodynamic Maglev vehicle

    International Nuclear Information System (INIS)

    Fife, A.A.; Ensing, H.J.; Tillotson, M.; Westera, W.

    1986-01-01

    A review is presented on the current status of superconducting magnet developments for the Canadian electrodynamic Maglev transportation system. Various design aspects of the levitation and linear synchronous motor magnets, appropriate for the current vehicle concepts, are discussed. In addition, recent experimental work is outlined on the development of a suitable epoxy impregnation technology for the superconducting coils

  11. 75 FR 34524 - Decision That Certain Nonconforming Motor Vehicles Are Eligible for Importation

    Science.gov (United States)

    2010-06-17

    ... Vehicles: 2007 Chevrolet Trailblazer Multipurpose Passenger Vehicle Manufactured Before September 1, 2007, for sale in Kuaiti Market. Substantially Similar U.S. Certified Vehicles: 2007 Chevrolet Trailblazer...

  12. Headway Deviation Effects on Bus Passenger Loads : Analysis of Tri-Met's Archived AVL-APC Data

    Science.gov (United States)

    2003-01-01

    In this paper we empirically analyze the relationship between transit service headway deviations and passenger loads, using archived data from Tri-Met's automatic vehicle location and automatic passenger counter systems. The analysis employs twostage...

  13. Fatigue Tests – Important Part of Development of New Vehicles

    Directory of Open Access Journals (Sweden)

    Kepka Miloslav

    2018-01-01

    Full Text Available In city of Pilsen (Czech Republic modern transport engineering is developed. The Skoda Transportation (production company has successfully been producing rail and road vehicles for many years (electric locomotives, trams, metro cars, trolleybuses, battery buses. This producer cooperates in developing these vehicles with the Research and Testing Institute (commercial research institute and with the University of West Bohemia (public university. Fatigue tests are carried out by the Dynamic Testing Laboratory at the Research and Testing Institute and by the Regional Technological Institute, the research center of the Faculty of Mechanical Engineering at the university. The paper describes various fatigue tests and presents their practical realization in the mentioned laboratories.

  14. An overview of the development of lead/acid traction batteries for electric vehicles in India

    Science.gov (United States)

    Sivaramaiah, G.; Subramanian, V. R.

    Electric vehicles (EVs) made an entry into the Indian scene quite recently in the area of passenger transportation, milk floats and other similar applications. The industrial EV market, with various models of fork-lift trucks and platform trucks already in wide use all over India, is a better understood application of EV batteries. The lead/acid traction batteries available in India are not of high-energy density. The best available indigenous lead/acid traction battery has an energy density ( C/5 rate) of 30 W h kg -1 as against 39 W h kg -1 available abroad. This paper reviews the developmental efforts relating to lead/acid traction batteries for electric vehicle applications in India, such as prototype road vehicles, commercial vehicles, rail cars, and locomotives. Due to the need for environmental protection and recognition of exhaustible, finite supplies of petroleum fuel, the Indian government is presently taking active interest in EV projects.

  15. The development of a pseudo-3D imaging system (tomosynthesis) for security screening of passenger baggage

    International Nuclear Information System (INIS)

    Reid, C.B.; Betcke, M.M.; Chana, D.; Speller, R.D.

    2011-01-01

    This paper describes a study investigating the potential of tomosynthesis as a post check-in baggage scanning system. A laboratory system has been constructed consisting of a moveable source and detector, arranged around a mini 90 o bend conveyor system, from which multiple projection images can be collected. Simulation code has been developed to allow the optimum source and detector positions to be determined. Reconstruction methods are being developed to modify the Shift-And-Add (SAA) algorithm to accommodate the non-typical imaging geometry.

  16. The development of a pseudo-3D imaging system (tomosynthesis) for security screening of passenger baggage

    Energy Technology Data Exchange (ETDEWEB)

    Reid, C.B., E-mail: c.reid@medphys.ucl.ac.uk [Department of Medical Physics and Bioengineering, University College London, London WC1E 6BT (United Kingdom); Betcke, M.M. [Department of Computer Science, University College London, London WC1E 6BT (United Kingdom); Chana, D. [Department for Transport, London SW1E 6DT (United Kingdom); Speller, R.D. [Department of Medical Physics and Bioengineering, University College London, London WC1E 6BT (United Kingdom)

    2011-10-01

    This paper describes a study investigating the potential of tomosynthesis as a post check-in baggage scanning system. A laboratory system has been constructed consisting of a moveable source and detector, arranged around a mini 90{sup o} bend conveyor system, from which multiple projection images can be collected. Simulation code has been developed to allow the optimum source and detector positions to be determined. Reconstruction methods are being developed to modify the Shift-And-Add (SAA) algorithm to accommodate the non-typical imaging geometry.

  17. NASA Green Flight Challenge: Conceptual Design Approaches and Technologies to Enable 200 Passenger Miles per Gallon

    Science.gov (United States)

    Wells, Douglas P.

    2011-01-01

    The Green Flight Challenge is one of the National Aeronautics and Space Administration s Centennial Challenges designed to push technology and make passenger aircraft more efficient. Airliners currently average around 50 passenger-miles per gallon and this competition will push teams to greater than 200 passenger-miles per gallon. The aircraft must also fly at least 100 miles per hour for 200 miles. The total prize money for this competition is $1.65 Million. The Green Flight Challenge will be run by the Comparative Aircraft Flight Efficiency (CAFE) Foundation September 25 October 1, 2011 at Charles M. Schulz Sonoma County Airport in California. Thirteen custom aircraft were developed with electric, bio-diesel, and other bio-fuel engines. The aircraft are using various technologies to improve aerodynamic, propulsion, and structural efficiency. This paper will explore the feasibility of the rule set, competitor vehicles, design approaches, and technologies used.

  18. Potential development of an intercity passenger transit system in Texas : final project report.

    Science.gov (United States)

    2010-05-01

    This report describes the findings of a research study of the potential for development of an intercity rail and : express bus system in the state of Texas. Rather than focus on regional commuter or light rail systems : radiating from urban areas, th...

  19. Using the Electronics Development Advantage in Creating a Buzz for the Airline Passengers

    Directory of Open Access Journals (Sweden)

    Bogdan AVRAM

    2013-12-01

    Full Text Available More and more airlines are trying to show their customers their ability to understand their needs, the market trends and the importance of technology in their lives. In response to the rapid development of the consumer electronics, the airline companies focus their attention on offering their customers the possibility to book a flight or check-in using a smartphone, spend time watching movies or be connected to the internet during the flight. Customers search for airlines who are more ”tech-geek” and opened to new technologies, which allows them to rate the airline companies through apps or connect more often with the airline through social-media. Technology has become an important part in developing and marketing the airline services for a better quality, more customer-focused and for better flight experience which ultimately makes the difference when choosing to fly an airline company.

  20. Near-term electric vehicle program: Phase I, final report

    Energy Technology Data Exchange (ETDEWEB)

    Rowlett, B. H.; Murry, R.

    1977-08-01

    A final report is given for an Energy Research and Development Administration effort aimed at a preliminary design of an energy-efficient electric commuter car. An electric-powered passenger vehicle using a regenerative power system was designed to meet the near-term ERDA electric automobile goals. The program objectives were to (1) study the parameters that affect vehicle performance, range, and cost; (2) design an entirely new electric vehicle that meets performance and economic requirements; and (3) define a program to develop this vehicle design for production in the early 1980's. The design and performance features of the preliminary (baseline) electric-powered passenger vehicle design are described, including the baseline power system, system performance, economic analysis, reliability and safety, alternate designs and options, development plan, and conclusions and recommendations. All aspects of the baseline design were defined in sufficient detail to verify performance expectations and system feasibility.

  1. Electrical faults in vehicle powernets - Methodical investigation of arcing faults in passenger cars and HGV; Fehlerfaelle in Fahrzeug-Bordnetzen - Methodische Untersuchung von Lichtboegen in Pkw und Lkw

    Energy Technology Data Exchange (ETDEWEB)

    Grosse, R.; Magenheimer, K.; Moenchmeier, A.; Stepec, H.; Viscido, T.; Wagner, C. [Forschungsgesellschaft Kraftfahrwesen Aachen mbH, Aachen (Germany)

    2004-07-01

    In vehicle powernets with a voltage higher than 20 V the possibility for the formation of electrical arcs is given. For that reason the electronics department of the fka analyses the characteristics of arc faults in vehicle powernets. Theoretical investigations and their validation by practical experiments help to determine the characteristic values of arcs. Regarding the insertion into powernets of real vehicles, either specific or general topologies get simulated. A further task of the ''fka powernet test bench'' is to bring out the technical validation of protection devices preventing arcing faults. For that purpose the protection devices get integrated into a realistic powernet replication to analyse their functionality. Within the scope of an analysis arcing faults were simulated which appear in commercial vehicle powernets by different reasons. For these purposes standard arcing tests were applied which are commonly used in aerospace and military applications. The analysis resulted in the cognition that a revision of the standard arcing tests is necessary to (a) improve the reproducibility of the tests, (b) to simulate the automotive surrounding more life like and (c) to enable a standardisation of the tests. In this article the revised tests are described. With these tests arc faults can be generated which can be used to verify the functionality of protection devices. The proposed tests can be used as a basis for standard tests. (orig.)

  2. Development of Bushing Compounds for Tracked Vehicles

    Science.gov (United States)

    1990-10-01

    unwanted stepchild - part of called anti patented NBR -12 formulation the family (system), but devoid of needed indicated that service life could be...as Development and Engineering Center’s long. Bushings currently used in the M I track Rubber and Coated Fabrics Research Group assembly typically fail...formulations of should be improved. Numerous selected candidate natural rubber , propylene formulations-based on natural rubber , oxide, and silicone

  3. Passenger car fuel consumption survey

    Energy Technology Data Exchange (ETDEWEB)

    1984-03-01

    This survey originated from a proposal to monitor the fuel consumption and fuel economy of personal use passenger cars operated in Canada. Its purpose is to establish a data base which would contain information on total distance travelled, total amount of fuel consumed, average distance obtained per unit of fuel, total expenditures on fuel, and seasonal fluctuations in fuel consumption and in distance travelled. Among the needs served by this data base are the monitoring of passenger car fuel economy standards and the estimation of pasenger car fuel requirements in conditions involving fuel shortages. Survey methodology is by telephone interview to trace selected vehicles to the registered owners, at which time a fuel purchase diary is then mailed to the principal driver of the car. The results are tabulated on a quarterly basis and to be released as they become available in bulletins similar to this. Data are presented for each province and the total for Canada is given. During the fourth quarter of 1982, it is estimated that there were 7.3 million personal use passenger cars operated in Canada. These cars were driven 28 billion kilometers and consumed 4.3 billion litres of fuel. Their average litres/100 kilometres and the average fuel consumption was 590 litres. 8 tabs.

  4. Development of the Tri-ATHLETE Lunar Vehicle Prototype

    Science.gov (United States)

    Heverly, Matt; Matthews, Jaret; Frost, Matt; Quin, Chris

    2010-01-01

    The Tri-ATHLETE (All Terrain Hex Limed Extra Terrestrial Explorer) vehicle is the second generation of a wheel-on-limb vehicle being developed to support the return of humans to the lunar surface. This paper describes the design, assembly, and test of the Tri-ATHLETE robotic system with a specific emphasis on the limb joint actuators. The design and implementation of the structural components is discussed, and a novel and low cost approach to approximating flight-like cabling is also presented. The paper concludes with a discussion of the "second system effect" and other lessons learned as well as results from a three week long field trial of the vehicle in the Arizona desert.

  5. Prospects of introduction of innovative technology overhead passenger traffic on the basis of the passenger ropeways for the modernization of the public transport system of the Bryansk city

    Directory of Open Access Journals (Sweden)

    Lagerev A.V.

    2017-06-01

    Full Text Available In relation to the current situation in the field of public transport in the Bryansk city was shown the main problems in the implementation of innovative technology for the aerial passenger transport on the basis of suspended passenger ropeways (Cable metro. Shows the advantages of the cable metro-based mechatronic technology transportation compared to the traditional suspended passenger ropeways. Was made the technical and economic feasibility analysis of the construction of the cable metro in conditions of a highly urbanized urban environment of large cities, metropolises and urban agglomerations. Presented the statistical data on the development of vehicles in the Bryansk city in the period 2004-2016 years and based on the analysis of these data shows the feasibility of the development of aerial passenger transport as the most high-speed and environmentally friendly mode of transport compared with automobile and electric transport. Considered the possible sources of financing of design and construction works and shows the commercial attractiveness of the project to potential investors in the framework of public-private partnerships. For existing urban development and major transport flows of the Bryansk city was formulated proposals for the location of future transport cable metro lines, order their gaskets, the formation routes of movement of the rolling stock. Made the estimation of labor and financial costs for the implementation of the project of modernization of the public transport system of the city of Bryansk on the basis of the suspended passenger ropeways. The proposed option has the following characteristics: the number of transport lines - 6, total length - 54.8 km, total number of passenger boarding stations - 26, hub passenger stations – 6, the total number of intermediate supports – 100...110 pieces with a span between supports of 400...600 m. the cost of construction of transport lines and the purchase of necessary

  6. Develop and pilot test smart phone/tablet app for paratransit demand-response passenger pick-up alerts to assist passengers with disabilities and reduce no-shows and dwell times.

    Science.gov (United States)

    2016-12-01

    This research produced an arrival notification system for paratransit passengers with disabilities. Almost all existing curb-to-curb paratransit services have significantly large pick-up time window ranging from 20 to 40 minutes from the scheduled ti...

  7. Vehicle classification using mobile sensors.

    Science.gov (United States)

    2013-04-01

    In this research, the feasibility of using mobile traffic sensors for binary vehicle classification on arterial roads is investigated. Features (e.g. : speed related, acceleration/deceleration related, etc.) are extracted from vehicle traces (passeng...

  8. Achieving integrated convoys: cargo unmanned ground vehicle development and experimentation

    Science.gov (United States)

    Zych, Noah; Silver, David; Stager, David; Green, Colin; Pilarski, Thomas; Fischer, Jacob

    2013-05-01

    The Cargo UGV project was initiated in 2010 with the aim of developing and experimenting with advanced autonomous vehicles capable of being integrated unobtrusively into manned logistics convoys. The intent was to validate two hypotheses in complex, operationally representative environments: first, that unmanned tactical wheeled vehicles provide a force protection advantage by creating standoff distance to warfighters during ambushes or improvised explosive device attacks; and second, that these UGVs serve as force multipliers by enabling a single operator to control multiple unmanned assets. To assess whether current state-of-the-art autonomous vehicle technology was sufficiently capable to permit resupply missions to be executed with decreased risk and reduced manpower, and to assess the effect of UGVs on customary convoy tactics, the Marine Corps Warfighting Laboratory and the Joint Ground Robotics Enterprise sponsored Oshkosh Defense and the National Robotics Engineering Center to equip two standard Marine Corps cargo trucks for autonomous operation. This paper details the system architecture, hardware implementation, and software modules developed to meet the vehicle control, perception, and planner requirements compelled by this application. Additionally, the design of a custom human machine interface and an accompanying training program are described, as is the creation of a realistic convoy simulation environment for rapid system development. Finally, results are conveyed from a warfighter experiment in which the effectiveness of the training program for novice operators was assessed, and the impact of the UGVs on convoy operations was observed in a variety of scenarios via direct comparison to a fully manned convoy.

  9. Development of an in-vehicle intersection collision countermeasure

    Science.gov (United States)

    Pierowicz, John A.

    1997-02-01

    Intersection collisions constitute approximately twenty-six percent of all accidents in the United States. Because of their complexity, and demands on the perceptual and decision making abilities of the driver, intersections present an increased risk of collisions between automobiles. This situation provides an opportunity to apply advanced sensor and processing capabilities to prevent these collisions. A program to determine the characteristics of intersection collisions and identify potential countermeasures will be described. This program, sponsored by the National Highway Traffic Safety Administration, utilized accident data to develop a taxonomy of intersection crashes. This taxonomy was used to develop a concept for an intersection collision avoidance countermeasure. The concept utilizes in-vehicle position, dynamic status, and millimeter wave radar system and an in-vehicle computer system to provide inputs to an intersection collision avoidance algorithm. Detection of potential violation of traffic control device, or proceeding into the intersection with inadequate gap will lead to the presentation of a warning to the driver. These warnings are presented to the driver primarily via a head-up display and haptic feedback. Roadside to vehicle communication provides information regarding phased traffic signal information. Active control of the vehicle's brake and steering systems are described. Progress in the development of the systems will be presented along with the schedule of future activities.

  10. Environmental Analysis of Petrol, Diesel and Electric Passenger Cars in a Belgian Urban Setting

    Directory of Open Access Journals (Sweden)

    Nils Hooftman

    2016-01-01

    Full Text Available The combustion of fossil fuels in the transport sector leads to an aggravation of the air quality along city roads and highways. Urban air quality is a serious problem nowadays as the number of vehicles increases on a yearly basis. With stricter Euro emission regulations, vehicle manufacturers are not meeting the imposed limits and are also disregarding the non-exhaust emissions. This paper highlights the relevance of non-exhaust emissions of passenger vehicles, both conventional (diesel and petrol or electric vehicles (EV, on air quality levels in an urban environment in Belgium. An environmental life cycle assessment was carried out based on a real-world emission model for passenger cars and fuel refinery data. A cut-off was applied to the models to highlight what emissions, both from the refinery to the exhaust and electricity production for EV, do actually occur within Belgium’s borders. Results show that not much progress has been made from Euro 4 to 6 for conventional vehicles. Electric vehicles pose the best alternative solution as a more environmentally friendly means of transportation. The analysis results target policy makers with the intention that regulations and policies would be developed in the future and target the characterization of non-exhaust emissions from vehicles. These results indicate that EVs offer a valid solution for addressing the urban air quality issue and that non-exhaust emissions should be addressed in future regulatory steps as they dominate the impact spectrum.

  11. Critical factors affecting life cycle assessments of material choice for vehicle mass reduction

    Science.gov (United States)

    This review examines the use of life-cycle assessments (LCAs) to compare different lightweight materials being developed to improve light-duty vehicle fuel economy. Vehicle manufacturers are designing passenger cars and light-duty trucks using lighter weight materials and design ...

  12. The Design and Operation of Suborbital Low Cost and Low Risk Vehicle to the Edge of Space (SOLVES)

    Science.gov (United States)

    Ridzuan Zakaria, Norul; Nasrun, Nasri; Rashidy Zulkifi, Mohd; Izmir Yamin, Mohd; Othman, Jamaludin; Rafidi Zakaria, Norul

    2013-09-01

    Inclusive in the planning of Spaceport Malaysia are 2 local suborbital vehicles development. One of the vehicles is called SOLVES or Suborbital Low Cost and Low Risk Vehicle to the Edge of Space. The emphasis on the design and operation of SOLVES is green and robotic technology, where both green technology and robotic technology are used to protect the environment and enhance safety. As SOLVES climbs, its center of gravity stabilizes and remains at the bottom as its propellant being used until it depletes, due to the position of the vehicle's passenger cabin and its engines at its lower end. It will reach 80km from sea level generally known as "the edge of space" due to its momentum although its propellant will be depleted at a lower altitude. As the suborbital vehicle descends tail first, its wings automatically extend and rotate at horizontal axes perpendicular to the fuselage. These naturally and passively rotating wings ensure controlled low velocity and stable descend of the vehicle. The passenger cabin also rotates automatically at a steady low speed at the centerline of its fuselage as it descends, caused naturally by the lift force, enabling its passengers a surrounding 360 degrees view. SOLVES is steered automatically to its landing point by an electrical propulsion system with a vectoring nozzle. The electrical propulsion minimizes space and weight and is free of pollution and noise. Its electrical power comes from a battery aided by power generated by the naturally rotating wings. When the vehicle lands, it is in the safest mode as its propellant is depleted and its center of gravity remains at the bottom of its cabin. The cabin, being located at the bottom of the fuselage, enables very convenient, rapid and safe entry and exit of its passengers. SOLVES will be a robotic suborbital vehicle with green technology. The vehicle will carry 4 passengers and each passenger will be trained to land the vehicle manually if the fully automated landing system fails

  13. Development in the technology of internal combustion engines for passenger cars over the next 10 to 15 years

    Energy Technology Data Exchange (ETDEWEB)

    Willand, J [Daimler Benz (Germany)

    1996-12-01

    The mainly use of fossil fuels and their limited resources and also the requirement of a 25% reduction of CO{sub 2}-emissions in Germany caused by the motor traffic, force the pressure on the car manufacturer to reduce the fuel consumption by respecting the emission limits given by the legislative institutions. The development of the worldwide vehicle population shows, that we can expect that markets like eastern Europe and developing countries will book the biggest amount of growing during the next decades. Related to this fact is also the amount of CO{sub 2}-Emissions caused by this countries. Of interest is that the emissions produced by cars will stagnate which is basically caused by the falling fuel consumption and in opposition the emissions of heavy trucks will expand over proportional. The reason is the strong expanding infrastructure in new markets and the fast growing number of heavy trucks in those countries. The target for Mercedes Benz is to reach a fuel economy until 2005 for the vehicle fleet of a maximum 6,0 liter / 100 km. Results concerning fuel economy could only be achieved on the base of progressive technologies. (EG)

  14. Preliminary development of a wing in ground effect vehicle

    Science.gov (United States)

    Abidin, Razali; Ahamat, Mohamad Asmidzam; Ahmad, Tarmizi; Saad, Mohd Rasdan; Hafizi, Ezzat

    2018-02-01

    Wing in ground vehicle is one of the mode of transportation that allows high speed movement over water by travelling few meters above the water level. Through this manouver strategy, a cushion of compressed air exists between the wing in ground vehicle wings and water. This significantly increase the lift force, thus reducing the necessity in having a long wing span. Our project deals with the development of wing in ground vehicle with the capability of transporting four people. The total weight of this wing in ground vehicle was estimated at 5.4 kN to enable the prediction on required wing area, minimum takeoff velocity, drag force and engine power requirement. The required takeoff velocity is decreases as the lift coefficient increases, and our current mathematical model shows the takeoff velocity at 50 m/s avoid the significant increase in lift coefficient for the wing area of 5 m2. At the velocity of 50 m/s, the drag force created by this wing in ground vehicle is well below 1 kN, which required a 100-120 kW of engine power if the propeller has the efficiency of 0.7. Assessment on the stresses and deflection of the hull structural indicate the capability of plywood to withstand the expected load. However, excessive deflection was expected in the rear section which requires a minor structural modification. In the near future, we expect that the wind tunnel tests of this wing in ground vehicle model would enable more definite prediction on the important parameters related to its performance.

  15. Development of heavy load carrying vehicle for nuclear power station

    International Nuclear Information System (INIS)

    Terabayashi, Yasuharu; Oono, Hiroo; Aizu, Takao; Kawaguchi, Kaname; Yamanaka, Masayuki; Hirobe, Tamio; Inagaki, Yoshiaki.

    1985-01-01

    In nuclear power stations, in order to carry out sound and stable operation, the routine inspection and regular inspection of machinery and equipment are performed, therefore, the transportation of heavy things is frequently carried out. Especially, the transportation of heavy things over the steps of passages and stairs requires much labor. Therefore, Chubu Electric Power Co., Inc. and Chubu Plant Service Co., Ltd. carried out the research on the development of a vehicle for transporting heavy components of nuclear power plants. In this research, it was aimed at developing a vehicle which can carry heavy components and get over a step, climb and descend stairs, and run through a narrow passage having many curves as well as running on flat ground. For this purpose, the actual state of the transportation of heavy things was investigated during the regular inspection of a nuclear power station, and on the basis of this results, a prototype vehicle was made and tested. Thereafter, a transporting vehicle of actual scale was made and tested. The investigation of actual state and the examination of the fundamental concept, the design, trial manufacture and verifying test are reported. (Kako, I.)

  16. 76 FR 11418 - Rear Visibility; Federal Motor Vehicle Safety Standard, Rearview Mirrors; Federal Motor Vehicle...

    Science.gov (United States)

    2011-03-02

    ... rulemaking (NPRM) to expand the required field of view for all passenger cars, trucks, multipurpose passenger... rear-mounted video camera and an in- vehicle visual display. Adoption of this proposal would...

  17. A comparison of hydrogen, methanol and gasoline as fuels for fuel cell vehicles: implications for vehicle design and infrastructure development

    Science.gov (United States)

    Ogden, Joan M.; Steinbugler, Margaret M.; Kreutz, Thomas G.

    All fuel cells currently being developed for near term use in electric vehicles require hydrogen as a fuel. Hydrogen can be stored directly or produced onboard the vehicle by reforming methanol, or hydrocarbon fuels derived from crude oil (e.g., gasoline, diesel, or middle distillates). The vehicle design is simpler with direct hydrogen storage, but requires developing a more complex refueling infrastructure. In this paper, we present modeling results comparing three leading options for fuel storage onboard fuel cell vehicles: (a) compressed gas hydrogen storage, (b) onboard steam reforming of methanol, (c) onboard partial oxidation (POX) of hydrocarbon fuels derived from crude oil. We have developed a fuel cell vehicle model, including detailed models of onboard fuel processors. This allows us to compare the vehicle performance, fuel economy, weight, and cost for various vehicle parameters, fuel storage choices and driving cycles. The infrastructure requirements are also compared for gaseous hydrogen, methanol and gasoline, including the added costs of fuel production, storage, distribution and refueling stations. The delivered fuel cost, total lifecycle cost of transportation, and capital cost of infrastructure development are estimated for each alternative. Considering both vehicle and infrastructure issues, possible fuel strategies leading to the commercialization of fuel cell vehicles are discussed.

  18. Modeling and Optimization of Collaborative Passenger Control in Urban Rail Stations under Mass Passenger Flow

    Directory of Open Access Journals (Sweden)

    Lili Wang

    2015-01-01

    Full Text Available With the rapid development of urban rail transit, the phenomenon of outburst passenger flows flocking to stations is occurring much more frequently. Passenger flow control is one of the main methods used to ensure passengers’ safety. While most previous studies have only focused on control measures inside the target station, ignoring the collaboration between stops, this paper puts emphasis on joint passenger control methods during the occurrence of large passenger flows. To provide a theoretic description for the problem under consideration, an integer programming model is built, based on the analysis of passenger delay and the processes by which passengers alight and board. Taking average passenger delay as the objective, the proposed model aims to disperse the pressure of oversaturated stations into others, achieving the optimal state for the entire line. The model is verified using a case study and the results show that restricted access measures taken collaboratively by stations produce less delay and faster evacuation. Finally, a sensitivity analysis is conducted, from which we find that the departure interval and maximum conveying capacity of the train affect passenger delay markedly in the process of passenger control and infer that control measures should be taken at stations near to the one experiencing an emergency.

  19. Integrated Computational Materials Engineering Development of Advanced High Strength Steel for Lightweight Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Hector, Jr., Louis G. [General Motors, Warren, MI (United States); McCarty, Eric D. [United States Automotive Materials Partnership LLC (USAMP), Southfield, MI (United States)

    2017-07-31

    The goal of the ICME 3GAHSS project was to successfully demonstrate the applicability of Integrated Computational Materials Engineering (ICME) for the development and deployment of third generation advanced high strength steels (3GAHSS) for immediate weight reduction in passenger vehicles. The ICME approach integrated results from well-established computational and experimental methodologies to develop a suite of material constitutive models (deformation and failure), manufacturing process and performance simulation modules, a properties database, as well as the computational environment linking them together for both performance prediction and material optimization. This is the Final Report for the ICME 3GAHSS project, which achieved the fol-lowing objectives: 1) Developed a 3GAHSS ICME model, which includes atomistic, crystal plasticity, state variable and forming models. The 3GAHSS model was implemented in commercially available LS-DYNA and a user guide was developed to facilitate use of the model. 2) Developed and produced two 3GAHSS alloys using two different chemistries and manufacturing processes, for use in calibrating and validating the 3GAHSS ICME Model. 3) Optimized the design of an automotive subassembly by substituting 3GAHSS for AHSS yielding a design that met or exceeded all baseline performance requirements with a 30% mass savings. A technical cost model was also developed to estimate the cost per pound of weight saved when substituting 3GAHSS for AHSS. The project demonstrated the potential for 3GAHSS to achieve up to 30% weight savings in an automotive structure at a cost penalty of up to $0.32 to $1.26 per pound of weight saved. The 3GAHSS ICME Model enables the user to design 3GAHSS to desired mechanical properties in terms of strength and ductility.

  20. Energy consumption and environmental effects of passenger transport modes. A life cycle study on passenger transport modes

    International Nuclear Information System (INIS)

    Kalenoja, H.

    1996-01-01

    Energy consumption and environmental effects of different passenger transport modes vary on the different stages of the fuel chain and during the production and maintenance of vehicles and infrastructure. Energy consumption and the environmental effects calculated per passenger mileage depend strongly on the vehicle occupancy. The properties of transport modes on urban areas and on the long distance transport have been evaluated in this study. The energy consumption and environmental effects calculated per passenger mileage have been assessed for passenger car, bus, tram, train, airplane and ferry. The emissions have been evaluated during the whole fuel chain. In this study only the airborne emissions have been taken into account. In the energy consumption calculations the energy content of vehicles and the infrastructure, energy consumption during the fuel chain and during the end use have been taken into consideration. (au)

  1. Integrated development of light armored vehicles based on wargaming simulators

    Science.gov (United States)

    Palmarini, Marc; Rapanotti, John

    2004-08-01

    Vehicles are evolving into vehicle networks through improved sensors, computers and communications. Unless carefully planned, these complex systems can result in excessive crew workload and difficulty in optimizing the use of the vehicle. To overcome these problems, a war-gaming simulator is being developed as a common platform to integrate contributions from three different groups. The simulator, OneSAF, is used to integrate simplified models of technology and natural phenomena from scientists and engineers with tactics and doctrine from the military and analyzed in detail by operations analysts. This approach ensures the modelling of processes known to be important regardless of the level of information available about the system. Vehicle survivability can be improved as well with better sensors, computers and countermeasures to detect and avoid or destroy threats. To improve threat detection and reliability, Defensive Aids Suite (DAS) designs are based on three complementary sensor technologies including: acoustics, visible and infrared optics and radar. Both active armour and softkill countermeasures are considered. In a typical scenario, a search radar, providing continuous hemispherical coverage, detects and classifies the threat and cues a tracking radar. Data from the tracking radar is processed and an explosive grenade is launched to destroy or deflect the threat. The angle of attack and velocity from the search radar can be used by the soft-kill system to carry out an infrared search and track or an illuminated range-gated scan for the threat platform. Upon detection, obscuration, countermanoeuvres and counterfire can be used against the threat. The sensor suite is completed by acoustic detection of muzzle blast and shock waves. Automation and networking at the platoon level contribute to improved vehicle survivability. Sensor data fusion is essential in avoiding catastrophic failure of the DAS. The modular DAS components can be used with Light Armoured

  2. The effect on road load due to variations in valid coast down tests for passenger cars

    NARCIS (Netherlands)

    Mensch, P. van; Ligterink, N.E.; Cuelenaere, R.F.A.

    2014-01-01

    Real-world CO2 emissions of passenger cars very often deviate from the Type Approval value. The Type Approval value for CO2 emissions of passenger cars is based on a chassis dynamometer test in a laboratory. The total vehicle resistance of a vehicle, or 'road load', is simulated on the chassis

  3. ANALYTICAL ESTIMATION OF MINIMUM AND MAXIMUM TIME EXPENDITURES OF PASSENGERS AT AN URBAN ROUTE STOP

    Directory of Open Access Journals (Sweden)

    Gorbachov, P.

    2013-01-01

    Full Text Available This scientific paper deals with the problem related to the definition of average time spent by passengers while waiting for transport vehicles at urban stops as well as the results of analytical modeling of this value at traffic schedule unknown to the passengers and of two options of the vehicle traffic management on the given route.

  4. Hardware in the loop platform development for hybrid vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Wilhelm, E. [ETH Zurich, Zurich (Switzerland); Fowler, E.; Stevens, M.B. [Waterloo Univ., ON (Canada). Dept. of Chemical Engineering; Fraser, M.W. [Waterloo Univ., ON (Canada). Dept. of Mechanical Engineering

    2007-07-01

    This paper described a hardware-in-the-loop (HIL) validation simulation system designed to evaluate hybrid control strategies. The system was designed to reduce development costs and improve the safety of hybrid vehicle control systems. Model-based design processes for power trains typically include a series of processes to assess the real time and physical limitations of control systems prior to in-vehicle testing. The study used a 70 kW nickel metal hydride battery; a 67 kW 3-phase induction traction motor; and, a high voltage DC-DC converter within a fuel cell Chevrolet Equinox. Two physical vehicle controllers were used to interface with the virtual vehicle simulation in real time. System performance was monitored with a supervisory computer. A software in the loop (SIL) process was conducted to assess torque control and regenerative braking algorithm validation. An analysis of the controller code showed that a Simulink-native integrator block was updating too slowly. A custom integration term calculation was written. The charge control was then validated and tuned. It was concluded that use of the HIL system mitigated the risk of component damage through the identification and correction of unstable control logic. 10 refs., 2 tabs., 10 figs.

  5. The Development of Vocational Vehicle Drive Cycles and Segmentation

    Energy Technology Data Exchange (ETDEWEB)

    Duran, Adam W. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Phillips, Caleb T. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Konan, Arnaud M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kelly, Kenneth J. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2017-09-28

    Under a collaborative interagency agreement between the U.S. Environmental Protection Agency and the U.S Department of Energy (DOE), the National Renewable Energy Laboratory (NREL) performed a series of in-depth analyses to characterize the on-road driving behavior including distributions of vehicle speed, idle time, accelerations and decelerations, and other driving metrics of medium- and heavy-duty vocational vehicles operating within the United States. As part of this effort, NREL researchers segmented U.S. medium- and heavy-duty vocational vehicle driving characteristics into three distinct operating groups or clusters using real world drive cycle data collected at 1 Hz and stored in NREL's Fleet DNA database. The Fleet DNA database contains millions of miles of historical real-world drive cycle data captured from medium- and heavy vehicles operating across the United States. The data encompass data from existing DOE activities as well as contributions from valued industry stakeholder participants. For this project, data captured from 913 unique vehicles comprising 16,250 days of operation were drawn from the Fleet DNA database and examined. The Fleet DNA data used as a source for this analysis has been collected from a total of 30 unique fleets/data providers operating across 22 unique geographic locations spread across the United States. This includes locations with topology ranging from the foothills of Denver, Colorado, to the flats of Miami, Florida. The range of fleets, geographic locations, and total number of vehicles analyzed ensures results that include the influence of these factors. While no analysis will be perfect without unlimited resources and data, it is the researchers understanding that the Fleet DNA database is the largest and most thorough publicly accessible vocational vehicle usage database currently in operation. This report includes an introduction to the Fleet DNA database and the data contained within, a presentation of the

  6. 77 FR 70538 - Final Decision That Certain Canadian-Certified Vehicles Are Eligible for Importation

    Science.gov (United States)

    2012-11-26

    .... 126 for all passenger cars and all multipurpose passenger vehicles, trucks, and buses with a GVWR of 4... vehicles, U.S. Standard Canadian standard Passenger cars trucks, and buses with a GVWR of 4,536 kg (10,000... Protection. CMVSS 214--Side Door X X Strength. FMVSS 222--School Bus Passenger CMVSS 222--School Bus School...

  7. Rail passengers rights

    Directory of Open Access Journals (Sweden)

    Đurđev Dušanka J.

    2016-01-01

    Full Text Available The legal framework of rail passengers rights is set out in a combination of international and European law: an international measure, the rather unwieldy Uniform Rules concerning the Contract for International Carriage of Passengers and Luggage by Rail, forming part of the Convention concerning International Carriage by Rail of 9 May 1980 (as amended by the Vilnius Protocol of 3 June 1999 ['CIV'], lays down a basic framework which is then fleshed out by more recent EU legislation, Regulation (EC No 1371/2007 on Rail Passengers ' Rights and Obligations. Regulation 1371/2007/EC on rail passenger rights and obligations sets out minimum quality standards that have to be guaranteed to all passengers on all lines. .

  8. Advanced PEFC development for fuel cell powered vehicles

    Science.gov (United States)

    Kawatsu, Shigeyuki

    Vehicles equipped with fuel cells have been developed with much progress. Outcomes of such development efforts include a Toyota fuel cell electric vehicle (FCEV) using hydrogen as the fuel which was developed and introduced in 1996, followed by another Toyota FCEV using methanol as the fuel, developed and introduced in 1997. In those Toyota FCEVs, a fuel cell system is installed under the floor of each RAV4L, to sports utility vehicle. It has been found that the CO concentration in the reformed gas of methanol reformer can be reduced to 100 ppm in wide ranges of catalyst temperature and gas flow rate, by using the ruthenium (Ru) catalyst as the CO selective oxidizer, instead of the platinum (Pt) catalyst known from some time ago. It has been also found that a fuel cell performance equivalent to that with pure hydrogen can be ensured even in the reformed gas with the carbon monoxide (CO) concentration of 100 ppm, by using the Pt-Ru (platinum ruthenium alloy) electrocatalyst as the anode electrocatalyst of a polymer electrolyte fuel cell (PEFC), instead of the Pt electrocatalyst known from some time ago.

  9. “Good passengers and not good passengers:” Adolescent drivers’ perceptions about inattention and peer passengers

    Science.gov (United States)

    Sommers, Marilyn S.

    2016-01-01

    Purpose The purpose of this qualitative focus group elicitation research study was to explore teen driver perceptions of peer passengers and driver inattention. Design & Methods We utilized focus groups for data collection and content analysis to analyze the data, both of which were guided by the Theory of Planned Behavior. We conducted 7 focus groups with 30 teens, ages 16–18, licensed for ≤1 year to examine attitudes, perceived behavioral control, and norms related to driving inattention and peer passengers. Results The sample was 50% male, mean age 17.39 (sd 0.52) with mean length of licensure 173.7 days (sd 109.2). Three themes emerged: 1) “Good and not good” passengers; 2) Passengers and technology as harmful and helpful; and 3) The driver is in charge. Conclusions While passengers can be a source of distraction, our participants also identified passenger behaviors that reduced risk, such as assistance with technology and guidance for directions. Practical Implications An understanding of teens’ perceptions of peer passengers can contribute to the development of effective interventions targeting teen driver inattention. Nurses are well-positioned to contribute to these teen crash prevention efforts. PMID:27496828

  10. Development of a Remotely Operated Vehicle Test-bed

    Directory of Open Access Journals (Sweden)

    Biao WANG

    2013-06-01

    Full Text Available This paper presents the development of a remotely operated vehicle (ROV, designed to serve as a convenient, cost-effective platform for research and experimental validation of hardware, sensors and control algorithms. Both of the mechanical and control system design are introduced. The vehicle with a dimension 0.65 m long, 0.45 m wide has been designed to have a frame structure for modification of mounted devices and thruster allocation. For control system, STM32 based MCU boards specially designed for this project, are used as core processing boards. And an open source, modular, flexible software is developed. Experiment results demonstrate the effectiveness of the test-bed.

  11. Passenger baggage object database (PBOD)

    Science.gov (United States)

    Gittinger, Jaxon M.; Suknot, April N.; Jimenez, Edward S.; Spaulding, Terry W.; Wenrich, Steve A.

    2018-04-01

    Detection of anomalies of interest in x-ray images is an ever-evolving problem that requires the rapid development of automatic detection algorithms. Automatic detection algorithms are developed using machine learning techniques, which would require developers to obtain the x-ray machine that was used to create the images being trained on, and compile all associated metadata for those images by hand. The Passenger Baggage Object Database (PBOD) and data acquisition application were designed and developed for acquiring and persisting 2-D and 3-D x-ray image data and associated metadata. PBOD was specifically created to capture simulated airline passenger "stream of commerce" luggage data, but could be applied to other areas of x-ray imaging to utilize machine-learning methods.

  12. Access improvement to aircraft passengers' hand luggage.

    Science.gov (United States)

    Alberda, W; Kampinga, O; Kassels, R; van Kester, R; Noriega, J; Vink, P

    2015-01-01

    Efficient use of space and passenger comfort in aircraft interiors are major issues. There is not much research available about the flying experience regarding passengers' personal belongings. The objective of this study is to explore concepts within the current aircraft seats which improve the passenger experience related to their personal belongings like wallets, mobile phones and laptops. Through on-site observations, interviews and online questionnaires, data regarding the number of personal belongings taken into the airplane and opinions about access to hand luggage were gathered. These data were used to develop different concepts to optimize the aircraft interior, which were evaluated by passengers. Almost every passenger carries a phone (88%), wallet (94%), travel documents (98%) and keys (76%) with them and they like to have these stored close by. Passengers rate the concept that provides integrated storage in the tray table of the aircraft seat the best. Extra storage possibility in the table-tray seems a promising solution according to the passengers.

  13. Government policy and the development of electric vehicles in Japan

    International Nuclear Information System (INIS)

    Ahman, Max

    2006-01-01

    The aim of this paper is to analyse the role that the Japanese Government has played in the development of alternatives to conventional vehicles, the effect of government programmes, and the importance of technical flexibility in government support schemes. The focus is on battery-powered electric vehicles (BPEVs), hybrid electric vehicles (HEVs), and fuel cell electric vehicles. The effects of government policy and the process of innovation are analysed from a systems approach drawing on the literature regarding technical change and innovation. The whole chain of government support, including the context in which these different policies have been implemented since the early 1970s, is studied. The Japanese Government has adopted a comprehensive strategy including R and D, demonstration programmes and market support guided by long-term strategic plans. The role of the Government has been that of a conductor in the development process supplying both R and D support and artificially created niche markets, and easing the way for targeted technologies by means of legislation and standards. Despite this, the targeted technology (the BPEV) has not been established on the market. However, the recent market success of the HEV can partly be attributed to the government support of the BPEV technology. The enabling component, the electric drivetrain, was developed for automotive use within the BPEV programmes offered by the MITI. This technology was later utilised in the HEV. The history of BPEVs in Japan demonstrates that 'picking winners' in government policy is not easy. Despite a sustained and ambitious policy by the MITI, the development of alternative vehicles never unfolded according to plan. The success factors for policy seem more related to technology specific features than the particular policy style. Our conclusion is that flexibility, adaptability and cooperation in terms of technical choice is necessary in policy. This increases the chances of a technology

  14. Development of a Refined Space Vehicle Rollout Forcing Function

    Science.gov (United States)

    James, George; Tucker, Jon-Michael; Valle, Gerard; Grady, Robert; Schliesing, John; Fahling, James; Emory, Benjamin; Armand, Sasan

    2016-01-01

    For several decades, American manned spaceflight vehicles and the associated launch platforms have been transported from final assembly to the launch pad via a pre-launch phase called rollout. The rollout environment is rich with forced harmonics and higher order effects can be used for extracting structural dynamics information. To enable this utilization, processing tools are needed to move from measured and analytical data to dynamic metrics such as transfer functions, mode shapes, modal frequencies, and damping. This paper covers the range of systems and tests that are available to estimate rollout forcing functions for the Space Launch System (SLS). The specific information covered in this paper includes: the different definitions of rollout forcing functions; the operational and developmental data sets that are available; the suite of analytical processes that are currently in-place or in-development; and the plans and future work underway to solve two immediate problems related to rollout forcing functions. Problem 1 involves estimating enforced accelerations to drive finite element models for developing design requirements for the SLS class of launch vehicles. Problem 2 involves processing rollout measured data in near real time to understand structural dynamics properties of a specific vehicle and the class to which it belongs.

  15. 78 FR 74225 - Decision That Certain Nonconforming Motor Vehicles Are Eligible for Importation

    Science.gov (United States)

    2013-12-10

    ... Importation 1. Docket No. NHTSA-2013-0033 Nonconforming Vehicles: 1996 Chevrolet Impala Passenger Cars Substantially Similar U.S. Certified Vehicles: 1996 Chevrolet Impala Passenger Cars Notice of Petition Published...

  16. 77 FR 55267 - Decision That Certain Nonconforming Motor Vehicles Are Eligible for Importation

    Science.gov (United States)

    2012-09-07

    ...-2012-0035 Nonconforming Vehicles: 1999-2006 Toyota Land Cruiser IFS 100 Series Multipurpose Passenger... Toyota Land Cruiser IFS 100 Series Multipurpose Passenger Vehicles Manufactured prior to September 1...

  17. Free Flight Rotorcraft Flight Test Vehicle Technology Development

    Science.gov (United States)

    Hodges, W. Todd; Walker, Gregory W.

    1994-01-01

    A rotary wing, unmanned air vehicle (UAV) is being developed as a research tool at the NASA Langley Research Center by the U.S. Army and NASA. This development program is intended to provide the rotorcraft research community an intermediate step between rotorcraft wind tunnel testing and full scale manned flight testing. The technologies under development for this vehicle are: adaptive electronic flight control systems incorporating artificial intelligence (AI) techniques, small-light weight sophisticated sensors, advanced telepresence-telerobotics systems and rotary wing UAV operational procedures. This paper briefly describes the system's requirements and the techniques used to integrate the various technologies to meet these requirements. The paper also discusses the status of the development effort. In addition to the original aeromechanics research mission, the technology development effort has generated a great deal of interest in the UAV community for related spin-off applications, as briefly described at the end of the paper. In some cases the technologies under development in the free flight program are critical to the ability to perform some applications.

  18. Development of commercial hybrid electric vehicle with native key components

    Directory of Open Access Journals (Sweden)

    S. V. Bakhmutov

    2014-01-01

    Full Text Available The perspectives of development of medium weight cargo vehicles with hybrid powertrain including Russian native key components are considered in this article. Series-parallel scheme of HEV is more relevant owing to limitations of series and parallel schemes. An example of this technology is described. This technical solution has good facilities for variation of HEV and AWD type. The authors have patented it. In addition, another main issue is to choose the types of key components with good correlation for parameters of ICE, electric motors, batteries, and inverter. Using mathematical model of the vehicle a selection and correlation of technical characteristics were carried out to meet ecological and economical requirements. After computing calculation two control strategies were accepted. The first strategy contributes to good fuel consumption, while the other one is aimed at ecology. Researchers use test benches to confirm the results of calculation, and this one was built by the authors applying native components. The result of experiment on the test bench is the growth of fuel consumption of the medium weight cargo vehicle by 25% and compliance with ecological class Euro-4.

  19. An Electric Vehicle Charging Management and its Impact on Losses

    DEFF Research Database (Denmark)

    Sinha, Rakesh; Moldes, Eloy Rodríguez; Zaidi, Arsalan Hussain

    2013-01-01

    In this paper, the statistics of passenger car usage in Denmark has been studied in order to obtain the possible future use of electric vehicles (EVs). On the basis of this analysis, a sequential charging management of EV has been developed and simulated in DIgSILENT power factory. Different cases...

  20. 75 FR 76692 - Federal Motor Vehicle Safety Standards; Small Business Impacts of Motor Vehicle Safety

    Science.gov (United States)

    2010-12-09

    ..., 510, 511, 512, 520, 523, 525, 526, and 571 [Docket No. NHTSA-2010-0159] Federal Motor Vehicle Safety Standards; Small Business Impacts of Motor Vehicle Safety AGENCY: National Highway Traffic Safety... that specifically relate to passenger cars, multipurpose passenger vehicles, trucks, buses, trailers...

  1. Estimating bus passenger waiting times from incomplete bus arrivals data

    OpenAIRE

    McLeod, F.N.

    2007-01-01

    This paper considers the problem of estimating bus passenger waiting times at bus stops using incomplete bus arrivals data. This is of importance to bus operators and regulators as passenger waiting time is a key performance measure. Average waiting times are usually estimated from bus headways, that is, time gaps between buses. It is both time-consuming and expensive to measure bus arrival times manually so methods using automatic vehicle location systems are attractive; however, these syste...

  2. Vision-based Vehicle Detection Survey

    Directory of Open Access Journals (Sweden)

    Alex David S

    2016-03-01

    Full Text Available Nowadays thousands of drivers and passengers were losing their lives every year on road accident, due to deadly crashes between more than one vehicle. There are number of many research focuses were dedicated to the development of intellectual driver assistance systems and autonomous vehicles over the past decade, which reduces the danger by monitoring the on-road environment. In particular, researchers attracted towards the on-road detection of vehicles in recent years. Different parameters have been analyzed in this paper which includes camera placement and the various applications of monocular vehicle detection, common features and common classification methods, motion- based approaches and nighttime vehicle detection and monocular pose estimation. Previous works on the vehicle detection listed based on camera poisons, feature based detection and motion based detection works and night time detection.

  3. Development of a method to rate the primary safety of vehicles using linked New Zealand crash and vehicle licensing data.

    Science.gov (United States)

    Keall, Michael D; Newstead, Stuart

    2016-01-01

    Vehicle safety rating systems aim firstly to inform consumers about safe vehicle choices and, secondly, to encourage vehicle manufacturers to aspire to safer levels of vehicle performance. Primary rating systems (that measure the ability of a vehicle to assist the driver in avoiding crashes) have not been developed for a variety of reasons, mainly associated with the difficult task of disassociating driver behavior and vehicle exposure characteristics from the estimation of crash involvement risk specific to a given vehicle. The aim of the current study was to explore different approaches to primary safety estimation, identifying which approaches (if any) may be most valid and most practical, given typical data that may be available for producing ratings. Data analyzed consisted of crash data and motor vehicle registration data for the period 2003 to 2012: 21,643,864 observations (representing vehicle-years) and 135,578 crashed vehicles. Various logistic models were tested as a means to estimate primary safety: Conditional models (conditioning on the vehicle owner over all vehicles owned); full models not conditioned on the owner, with all available owner and vehicle data; reduced models with few variables; induced exposure models; and models that synthesised elements from the latter two models. It was found that excluding young drivers (aged 25 and under) from all primary safety estimates attenuated some high risks estimated for make/model combinations favored by young people. The conditional model had clear biases that made it unsuitable. Estimates from a reduced model based just on crash rates per year (but including an owner location variable) produced estimates that were generally similar to the full model, although there was more spread in the estimates. The best replication of the full model estimates was generated by a synthesis of the reduced model and an induced exposure model. This study compared approaches to estimating primary safety that could mimic

  4. Study on Emission Measurement of Vehicle on Road Based on Binomial Logit Model

    OpenAIRE

    Aly, Sumarni Hamid; Selintung, Mary; Ramli, Muhammad Isran; Sumi, Tomonori

    2011-01-01

    This research attempts to evaluate emission measurement of on road vehicle. In this regard, the research develops failure probability model of vehicle emission test for passenger car which utilize binomial logit model. The model focuses on failure of CO and HC emission test for gasoline cars category and Opacity emission test for diesel-fuel cars category as dependent variables, while vehicle age, engine size, brand and type of the cars as independent variables. In order to imp...

  5. Consistent further development of the high pressure diesel fuel injection systems for passenger cars; Konsequente Weiterentwicklung der Hochdruck-Pkw-Dieseleinspritzsysteme

    Energy Technology Data Exchange (ETDEWEB)

    Warga, Johann; Pauer, Thomas; Boecking, Friedrich; Gerhardt, Juergen; Leonhard, Rolf [Robert Bosch GmbH, Stuttgart-Feuerbach (Germany). Diesel Systems

    2011-07-01

    Since the introduction of common rail technology in modern diesel engines for passenger cars there have been many changes and technological revolutions. Solely the continuous increase of the maximum injection pressure has remained unchanged as a guarantee for further engine performance improvement. Whether for down-sizing or for just simply increase the engine power or to reduce CO2 or to improve emissions: In all aspects the injection pressure can offer possible degrees of freedom. Besides, parallel to this continuous increase of injection pressure, the requirements concerning other injection system features have also continuously further developed. This paper focuses on the achievability of EU6 applications, among others, with the new Bosch 2000 bar solenoid valve injector, innovative nozzle technologies as e.g. with improved spray hole geometry or the modular concept common rail pump CP4. Current engine tests with pressures up to 2500 bar prove clearly the further advantages of pressure increase in diesel engines for passenger cars. In addition to the hydraulic components, system approaches in combination with electronic control, sensors and innovative control algorithms are increasingly in focus aiming to improve system accuracy and robustness. (orig.)

  6. Development of a prototype specialist shuttle vehicle for chipped woodfuel

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-06-01

    This report gives details of a project to develop and test a specialist chip shuttle vehicle for conveying woodchips out of the forest with the aim of reducing the cost of woodfuel production. The design objectives are described and include the need to allow easy transfer of the chips from the chipper to the shuttle and on into haulage units, good performance and manoeuvrability on and off roads, and high-tip capacity. Estimates of the improved production and reduced woodfuel production costs are discussed along with the anticipated satisfactory operation of the chipper-shuttle combination in a forestry site.

  7. Development of quick charging system for electric vehicle

    Energy Technology Data Exchange (ETDEWEB)

    Anegawa, Takafumi

    2010-09-15

    Despite low environmental impact and high energy efficiency, electric vehicles (EV) have not been widely accepted. The lack of charging infrastructure is one reason. Since lithium-ion battery has high energy density and low internal resistance that allows quick charging, the convenience of EV may be greatly improved if charging infrastructure is prepared adequately. TEPCO aims for EV spread to reduce CO2 emissions and to increase demand for electric power, and has developed quick charging system for fleet-use EV to improve the convenience of EV. And based on research results, we will propose desirable characteristics of quick charger for public use.

  8. In-use vs. type-approval fuel consumption of current passenger cars in Europe

    International Nuclear Information System (INIS)

    Ntziachristos, L.; Mellios, G.; Tsokolis, D.; Keller, M.; Hausberger, S.; Ligterink, N.E.; Dilara, P.

    2014-01-01

    In-use fuel consumption data of 924 passenger cars (611 petrol, 313 diesel) were collected from various European sources and were evaluated in comparison to their corresponding type-approval values. The analysis indicated that the average in-use fuel consumption was higher than the type-approval one by 11% for petrol cars and 16% for diesel cars. Comparison of this dataset with the Travelcard database in the Netherlands showed that the deviation increased for late model years and in particular for cars with low type-approval values. The deviation was higher than 60% for vehicles registered in 2012 within the 90–100 gCO 2 /km bin. Unrealistic vehicle resistances used in type-approval were identified as one of the prime reasons of the difference. A simplified linear model developed in the study may be used to predict in-use fuel consumption based on data publicly available. The model utilizes the fuel consumption measured in type-approval, the mass, and the engine capacity to provide in-use fuel consumption. This may be either used to correct fuel consumption factors currently utilized by emission models (e.g. COPERT, HBEFA, VERSIT+, and others) or could be used independently to make projections on how fuel consumption may develop on the basis of changing future passenger cars characteristics. - Highlights: • In-use fuel consumption of petrol and diesel passenger cars is 11% and 16% higher than type-approval, respectively. • The relative difference between in-use and type-approval increases for late model and vehicles with low consumption. • Unrealistically low vehicle resistances are identified as a prime reason of low type-approval fuel consumption. • A model developed predicts in-use consumption on the basis of type-approval consumption, vehicle mass, and engine capacity

  9. Wheelchair tiedown and occupant restraint practices in paratransit vehicles.

    Science.gov (United States)

    Frost, Karen; Bertocci, Gina; Smalley, Craig

    2018-01-01

    The purpose of this study was to characterize wheelchair tiedown and occupant restraint system (WTORS) usage in paratransit vehicles based on observations of wheelchair and scooter (wheeled mobility devices, collectively, "WhMD") passenger trips. A retrospective review of on-board video monitoring recordings of WhMD trips was conducted. Four hundred seventy-five video recordings were collected for review and analysis. The use of all four tiedowns to secure the WhMD was observed more frequently for power WhMDs (82%) and manual WhMDs (80%) compared to scooters (39%), and this difference was significant (pinjuries in this study, misuse and nonuse of WTORS potentially place WhMD seated passengers at higher risk of injury during transit. These findings support the need for improved vehicle operator training and passenger education on the proper use of WTORS and development of WTORS with improved usability and/or alternative technologies that can be automated or used independently.

  10. Implementation and development of vehicle tracking and immobilization technologies.

    Science.gov (United States)

    2010-01-01

    Since the mid-1980s, limited use has been made of vehicle tracking using satellite communications to mitigate the security and safety risks created by the highway transportation of certain types of hazardous materials. However, vehicle-tracking techn...

  11. Cartalk 2000: development of a co-operative ADAS based on vehicle-to-vehicle communication

    NARCIS (Netherlands)

    Morsink, P.L.J.; Hallouzi, R.; Dagli, I.; Cseh, C.; Schäfers, L.; Nelisse, M.W.; Bruin, D. de

    2003-01-01

    Advanced Driver Assistance Systems (ADAS) benefit from using vehicle-to-vehicle communication. In the 5th framework EC project CarTALK2000 co-operative ADAS are designed, tested and evaluated with respect to increasing traffic safety, efficiency and driving comfort. Communication based longitudinal

  12. The Development of Lightweight Commercial Vehicle Wheels Using Microalloying Steel

    Science.gov (United States)

    Lu, Hongzhou; Zhang, Lilong; Wang, Jiegong; Xuan, Zhaozhi; Liu, Xiandong; Guo, Aimin; Wang, Wenjun; Lu, Guimin

    Lightweight wheels can reduce weight about 100kg for commercial vehicles, and it can save energy and reduce emission, what's more, it can enhance the profits for logistics companies. The development of lightweight commercial vehicle wheels is achieved by the development of new steel for rim, the process optimization of flash butt welding, and structure optimization by finite element methods. Niobium micro-alloying technology can improve hole expansion rate, weldability and fatigue performance of wheel steel, and based on Niobium micro-alloying technology, a special wheel steel has been studied whose microstructure are Ferrite and Bainite, with high formability and high fatigue performance, and stable mechanical properties. The content of Nb in this new steel is 0.025% and the hole expansion rate is ≥ 100%. At the same time, welding parameters including electric upsetting time, upset allowance, upsetting pressure and flash allowance are optimized, and by CAE analysis, an optimized structure has been attained. As a results, the weight of 22.5in×8.25in wheel is up to 31.5kg, which is most lightweight comparing the same size wheels. And its functions including bending fatigue performance and radial fatigue performance meet the application requirements of truck makers and logistics companies.

  13. Development of a hybrid pneumatic-power vehicle

    International Nuclear Information System (INIS)

    Huang, K. David; Tzeng, S.-C.

    2005-01-01

    Many complex technologies have been developed and applied to improve the energy efficiency and exhaust emission of an engine under different driving conditions. The overall thermal efficiency of an internal-combustion engine, however, can be maintained at only about 20-30%, with aggravated problems in the design and development, such as overall difficulty, excessive time consumption or excessively high cost. For electric cars, there is still no major technological breakthrough for the rapid recharging of a large capacity battery and detection of remaining power in it. Although all currently available hybrid-power engines are able to lower the amount of exhaust emissions and the fuel consumption of the engine, they are still unable to achieve a stable and optimal running condition immediately after ignition; hence the engine's thermal-efficiency remains low. To solve the aforementioned problems, an innovative concept - a hybrid pneumatic power-system (HPPS), which stores 'flow work' instead of storing electrochemical energy of the battery - is introduced. This innovative power system not only ensures that the internal-combustion ensures optimally but also recycles the exhaust flow to propel the vehicle. The optimization of the internal-combustion and recycling of the exhaust energy can increase the vehicle's efficiency from an original 15% to 33%, an overall increase of 18%

  14. Updraft Model for Development of Autonomous Soaring Uninhabited Air Vehicles

    Science.gov (United States)

    Allen, Michael J.

    2006-01-01

    Large birds and glider pilots commonly use updrafts caused by convection in the lower atmosphere to extend flight duration, increase cross-country speed, improve range, or simply to conserve energy. Uninhabited air vehicles may also have the ability to exploit updrafts to improve performance. An updraft model was developed at NASA Dryden Flight Research Center (Edwards, California) to investigate the use of convective lift for uninhabited air vehicles in desert regions. Balloon and surface measurements obtained at the National Oceanic and Atmospheric Administration Surface Radiation station (Desert Rock, Nevada) enabled the model development. The data were used to create a statistical representation of the convective velocity scale, w*, and the convective mixing-layer thickness, zi. These parameters were then used to determine updraft size, vertical velocity profile, spacing, and maximum height. This paper gives a complete description of the updraft model and its derivation. Computer code for running the model is also given in conjunction with a check case for model verification.

  15. Compressed hydrogen fuelled vehicle at ENEA: Status and development

    International Nuclear Information System (INIS)

    Pede, G.; Ciancia, A.

    1993-01-01

    The world's 500 million road vehicles using internal combustion engines account for roughly half of global oil consumption and, in Italy, for about 50% of all nitrogen oxide and 90% of carbon monoxide emissions. In efforts to conserve petroleum reserves and reduce air pollution, research programs are being conducted to develop hydrogen fueled automotive engines. Hydrogen combustion products are carbon dioxide free, and when burned with a large excess of air, this fuel produces water vapour and only small amounts of nitrogen oxides. Hydrogen fueled vehicles can be made to operate in a dual fuel mode so as to allow the use of petrol or diesel fuel in travel over long distances. Currently, because technical and economic difficulties relevant to hydrogen fuel storage limit driving range and payload (there are bulk and weight problems in compressed gas and metal hydride storage systems, and cost problems in cryogenic storage), only limited research programs are being performed, mainly in Germany (by Mercedes Benz) and Japan. Some recent advances, however, relevant to research in gas storage and gaseous mixtures have been made by ENEA (the Italian Agency for New Technology, Energy and the Environment). This paper outlines the progress being made in ENEA's research efforts which include the development of an electronically controlled hydrogen fuel injection system prototype

  16. Influence of unsteady aerodynamics on driving dynamics of passenger cars

    Science.gov (United States)

    Huemer, Jakob; Stickel, Thomas; Sagan, Erich; Schwarz, Martin; Wall, Wolfgang A.

    2014-11-01

    Recent approaches towards numerical investigations with computational fluid dynamics methods on unsteady aerodynamic loads of passenger cars identified major differences compared with steady-state aerodynamic excitations. Furthermore, innovative vehicle concepts such as electric-vehicles or hybrid drives further challenge the basic layout of passenger cars. Therefore, the relevance of unsteady aerodynamic loads on cross-wind stability of changing basic vehicle architectures should be analysed. In order to assure and improve handling and ride characteristics at high velocity of the actual range of vehicle layouts, the influence of unsteady excitations on the vehicle response was investigated. For this purpose, a simulation of the vehicle dynamics through multi-body simulation was used. The impact of certain unsteady aerodynamic load characteristics on the vehicle response was quantified and key factors were identified. Through a series of driving simulator tests, the identified differences in the vehicle response were evaluated regarding their significance on the subjective driver perception of cross-wind stability. Relevant criteria for the subjective driver assessment of the vehicle response were identified. As a consequence, a design method for the basic layout of passenger cars and chassis towards unsteady aerodynamic excitations was defined.

  17. The development of low-carbon vehicles in China

    International Nuclear Information System (INIS)

    Yao Mingfa; Liu Haifeng; Feng Xuan

    2011-01-01

    Reducing CO 2 emissions from vehicles in China is crucial and will significantly alleviate the environmental burden of the Earth. Some promising technologies that make possible low-carbon vehicles are reviewed in this work, including electric vehicles, fuel cell vehicles, hybrid vehicles, biofuels vehicles, other alternative fuel vehicles, and conventional internal combustion engine vehicles with improvement. In the short term, expanding the use of mature technologies in conventional gasoline or diesel vehicles is the most realistic, effective, and timely solution for China to meeting the urgent challenges of energy saving and greenhouse gas reduction; while in the long run biofuel is a promising candidate due to their renewability and carbon neutrality. The blueprint of low-carbon vehicles for China depends on three aspects: breakthroughs in technology, awareness of public, and government guidance. - Highlights: → Reducing CO 2 emissions and saving energy from vehicles in China is crucial. → Low-carbon depends on technology breakthrough, public awareness, and government guidance. → Use of mature technologies in ICEVs is the most realistic solution for China. → Biofuels are the key to realize neutral carbon emission in the long run.

  18. Development Of Translational Motion Of Unmanned Aerial Vehicle Using MATLAB

    Directory of Open Access Journals (Sweden)

    Thwe Thwe Htoo

    2015-08-01

    Full Text Available This research work describes the translational motion analysis of unmanned aerial vehicle UAV. Since the center of mass of the receiver is timevarying the equations are written in a reference frame that is geometrically fixed in the aircraft. Due to the fact that aerial vehicle simulation and control deal with the position and orientation of the UAV the equations of motion are derived in terms of the translational and rotational position and velocity with respect to the aircraft location. The formation relative motion control is a challenging problem due to the coupled translational and rotational dynamics. As the translational vector depends on the current attitude and its angular velocity and some of the attitude constraints also couple the position and attitude of the spacecraft it makes the formation control problem high dimensional. This work develops UAV stability conditions including translational vector maneuverability condition and included angle condition between the translational and the rotational motion of UAV system and then presents two methods to calculate the UAV attitude. Both of the two methods need first design the optimal trajectory of the translational vector and then use geometric and nonlinear programming methods to calculate the target trajectory. The validity of the proposed approach is demonstrated in a UAV by using MATLAB. The performance of the translational motion control is evaluated by the simulated results.

  19. Novel adjuvants & delivery vehicles for vaccines development: a road ahead.

    Science.gov (United States)

    Mohan, Teena; Verma, Priyanka; Rao, D Nageswara

    2013-11-01

    The pure recombinant and synthetic antigens used in modern day vaccines are generally less immunogenic than older style live/attenuated and killed whole organism vaccines. One can improve the quality of vaccine production by incorporating immunomodulators or adjuvants with modified delivery vehicles viz. liposomes, immune stimulating complexes (ISCOMs), micro/nanospheres apart from alum, being used as gold standard. Adjuvants are used to augment the effect of a vaccine by stimulating the immune system to respond to the vaccine, more vigorously, and thus providing increased immunity to a particular disease. Adjuvants accomplish this task by mimicking specific sets of evolutionary conserved molecules which include lipopolysaccharides (LPS), components of bacterial cell wall, endocytosed nucleic acids such as dsRNA, ssDNA and unmethylated CpG dinucleotide containing DNA. This review provides information on various vaccine adjuvants and delivery vehicles being developed to date. From literature, it seems that the humoral immune responses have been observed for most adjuvants and delivery platforms while viral-vector, ISCOMs and Montanides have shown cytotoxic T-cell response in the clinical trials. MF59 and MPL® have elicited Th1 responses, and virus-like particles (VLPs), non-degradable nanoparticle and liposomes have also generated cellular immunity. Such vaccine components have also been evaluated for alternative routes of administration with clinical success reported for intranasal delivery of viral-vectors and proteosomes and oral delivery of VLP vaccines.

  20. Urban passenger transport energy saving and emission reduction potential: A case study for Tianjin, China

    International Nuclear Information System (INIS)

    Peng, Binbin; Du, Huibin; Ma, Shoufeng; Fan, Ying; Broadstock, David C.

    2015-01-01

    Highlights: • Potential to reduce urban passenger transport is projected between 2010 and 2040. • Four scenarios reflecting different policy mixes are considered. • The potential for energy conservation and emission reductions are obtained. • Vehicle population regulation is most effective in energy saving and reducing overall GHG. • Emission standards are the most effective measure to reduce pollutant emissions. - Abstract: With rapid growth of the vehicle population, urban passenger transport in China is largely responsible for increases in energy consumption, greenhouse gas (GHG) emissions, and also atmospheric pollutants (NO x , CO, HC, PM). In this paper, we first develop an urban passenger transport energy saving and emission reduction potential evaluation model using the “Long Range Energy Alternatives Planning (LEAP)” tool; and then take Tianjin city as an empirical case to evaluate the reduction potential of final energy consumption, GHG emissions and pollutants emissions of Tianjin’s urban passenger transport sector between 2010 and 2040 under four scenarios, i.e. BAU (business as usual) scenario, PP (the 12th five-year plan policy) scenario, CP (comprehensive policy) scenario and HP (hybrid policy of PP and CP) scenario. The results show that due to the public transport promotion, energy consumption and CO 2 emissions in 2040 can be reduced by 22% and 22.6% in the PP scenario, compared to BAU. The largest reductions in energy consumption, CO 2 and atmospheric pollutants emissions can be achieved under CP scenario, in which vehicle population regulation is the most effective to be implemented. Emissions standard regulation is the most effective measure to reduce atmospheric pollutant emissions in all the scenarios and green energy promotion is especially effective to reduce NO x and PM

  1. Substantial improvements of fuel economy. Potentials of electric and hybrid electric vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Joergensen, K [Technical Univ. of Denmark (Denmark); Nielsen, L H [Forskningscenter Risoe (Denmark)

    1996-12-01

    This paper evaluates the scope for improvement of the energy and environmental impacts of road traffic by means of electrical and hybrid electric propulsion. These technologies promise considerable improvements of the fuel economy of vehicles compared to the present vehicle types as well as beneficial effects for the energy and traffic system. The paper - based on work carried out in the project `Transportation fuel based on renewable energy`, funded by the National Energy Agency of Denmark and carried out by Department of Buildings and Energy, Technical University of Denmark and System Analysis Department, Risoe National Laboratory - assesses the potentials for reduction of the primary energy consumption and emissions, and points to the necessary technical development to reap these benefits. A case study concerning passenger cars is analysed by means of computer simulations, comparing electric and hybrid electric passenger car to an equivalent reference vehicle (a conventional gasoline passenger car). (au) 10 refs.

  2. National Motor Vehicle Crash Causation Survey (NMVCCS)

    Data.gov (United States)

    Department of Transportation — The National Motor Vehicle Crash Causation Survey (NMVVCS) was a nationwide survey of crashes involving light passenger vehicles, with a focus on the factors related...

  3. Research, development, and demonstration of lead-acid batteries for electric vehicle propulsion. Annual report, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-03-01

    The progress and status of Eltra's Electric Vehicle Battery Program during FY-80 are presented under five divisional headings: Research on Components and Processes; Development of Cells and Modules for Electric Vehicle Propulsion; Sub-Systems; Pilot Line Production of Electric Vehicle Battery Prototypes; and Program Management.

  4. ISSUES OF ORGANIZING THE PASSENGER TRANSPORTATION ON US RAILWAYS

    Directory of Open Access Journals (Sweden)

    R. H. Korobiova

    2017-04-01

    Full Text Available Purpose. The paper focuses on a study of the US railway transport organization management during passenger transportation. Methodology. Studies were carried out on the basis of the analysis of literature sources and reporting data on passenger transportation in the USA. Findings. Negative trends in the work of the passenger complex of the Ukrainian railways are the slowdown in the volumes of transportation, the progressive aging of the rolling stock and the overall activity running at a loss for Ukrzaliznytsia. In this regard, the actual task for domestic rail transport is the implementation of industry reforms. Therefore, the paper presented the study of the experience of organizing the passenger transportation on US railways, whose peculiarity is the extremely high degree of competition between modes of transport. As a result of the conducted analysis for working conditions of the US and Ukrainian railways, the general conditions for the functioning of the railways in both countries connected with passenger transportation securing have been established. It was found that general condition for execution of railway passenger transportation for the United States and Ukraine is the subsidization of this activity and combined use of infrastructure for the freight and passengers’ transportations. In this connection, when developing approaches to reforming the passenger economy of Ukraine's railways, it is advisable to use the experience of the United States in assessing the social effectiveness of rail transport, the impact of passenger transportation on the conditions of freight trains handling, and combined use of railway infrastructure by freight and passenger companies. Originality. The author determined the general trends in the development of passenger railway transportation in the US and Ukraine. Practical value. The resulted methods of organizing the operation of the US railway passenger transportation complex can be adapted to solve

  5. Development of a methanol reformer for fuel cell vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Lindstroem, Baard

    2003-03-01

    Vehicles powered by fuel cells are from an environmental aspect superior to the traditional automobile using internal combustion of gasoline. Power systems which are based upon fuel cell technology require hydrogen for operation. The ideal fuel cell vehicle would operate on pure hydrogen stored on-board. However, storing hydrogen on-board the vehicle is currently not feasible for technical reasons. The hydrogen can be generated on-board using a liquid hydrogen carrier such as methanol and gasoline. The objective of the work presented in this thesis was to develop a catalytic hydrogen generator for automotive applications using methanol as the hydrogen carrier. The first part of this work gives an introduction to the field of methanol reforming and the properties of a fuel cell based power system. Paper I reviews the catalytic materials and processes available for producing hydrogen from methanol. The second part of this thesis consists of an experimental investigation of the influence of the catalyst composition, materials and process parameters on the activity and selectivity for the production of hydrogen from methanol. In Papers II-IV the influence of the support, carrier and operational parameters is studied. In Paper V an investigation of the catalytic properties is performed in an attempt to correlate material properties with performance of different catalysts. In the third part of the thesis an investigation is performed to elucidate whether it is possible to utilize oxidation of liquid methanol as a heat source for an automotive reformer. In the study which is presented in Paper VI a large series of catalytic materials are tested and we were able to minimize the noble metal content making the system more cost efficient. In the final part of this thesis the reformer prototype developed in the project is evaluated. The reformer which was constructed for serving a 5 k W{sub e} fuel cell had a high performance with near 100 % methanol conversion and CO

  6. Development of a submersible gravimeter on underwater vehicles

    Science.gov (United States)

    Yamada, T.; Kanazawa, T.; Fujimoto, H.; Shinohara, M.; Ishihara, T.; Araya, A.; Iizasa, K.; Tsukioka, S.

    2012-12-01

    Gravity is one of the powerful indices to profile underground structures. Surface ship gravimeters are popular tool for the purpose of collecting gravity values in marine region. They enable you to obtain gravity values from large area easily, while the resolutions are relatively low because of the distance between the sea surface and bottom. Otherwise, ocean bottom gravimeters are able to be observed gravity with high resolution, but they have still covered few limited sites so that they are designed to do observation in quiet only. In some cases, such as hydrothermal deposit survey, the medium performance both in resolution and size of survey area are required. This paper describes a gravimeter we have been developing for satisfying the requirements. Our target is to detect gravity anomalies less than 1 mgal by using an underwater vehicle. This setting is roughly equivalent to find a typical hydrothermal deposit with a dimension of 0.5 km x 0.5 km x 10 m and a density contrast of 1 g/cm3 when we set the sensor at 50 m high from the seafloor. There are some issues such as noise reduction, robustness and downsizing to clear the target. A gravity sensor (Micro-g LaCoste S-174) is mounted on a gimbal control unit with an inertial navigation sensor for the problems. These are stored in a sphere vessel made of titanium alloy (125 kgf in air, 32 kgf in water) and it is available in 3500 m below sea surface. Furthermore, in order to reduce high frequency noise due to mainly the vehicle motion through a low-pass filter, data are able to be stored at sampling rates of approximately 100 Hz. The logging system and control unit for communication to/from ship is stored another canister (22 kgf in air, 10 kgf in water). We made gravity measurement experiments to examine the effectiveness of the gimbal system and filtering application. The gravimeter was set on a machine simulating pitch and roll motions with a period of 16 s and an amplitude of 7.5 degrees, which is greater

  7. Concept development of control system for perspective unmanned aerial vehicles

    Directory of Open Access Journals (Sweden)

    Koryanov Vsevolod V.

    2018-01-01

    Full Text Available Presented actual aspects of the development of the control system of unmanned aerial vehicles (UAVs in the example of perspective. Because the current and future UAV oriented to implementation of a wide range of tasks, taking into account the use of several types of payload, in this paper discusses the general principles of construction of onboard control complex, in turn, a hardware implementation of the automatic control system has been implemented in the microcontroller Arduino platform and the Raspberry Pi. In addition, in the paper presents the most common and promising way to ensure the smooth and reliable communication of the command post with the UAV as well as to the ways of parry considered and abnormal situations.

  8. International Passenger and Freight Report

    Data.gov (United States)

    Department of Transportation — The International Passenger and Freight report is a summarization of all passengers and all freight transported between the U.S. and foreign countries combined, with...

  9. Development of lithium air novel materials for electrical vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Aucher, Christophe; Knipping, E.; Amantia, D.; Almarza, A.; Faccini, M.; Gutierrez-Tauste, D.; Saez, J.A.; Aubouy, L. [Leitat Technological Center, Terrassa (Spain)

    2012-07-01

    Fluctuation of oil prices and effects of global warming have forced the scientific-technical community to look for the alternative energy storage and conversion systems, such as the smart grid. The maximum energy density of current lithium-ion batteries (LIB) is limited because of the intercalation chemistry of each electrode. Then actual LIBs are not fully satisfactory for the practical application of electric vehicles (EV). Therefore metal-air batteries have attracted much attention as a possible alternative, especially for the replacing of the diesel or gasoline, because of their energy density is extremely high compared to that of other rechargeable batteries and theoretically close to the energy density of the fossil energy. This technology leads to a very light dispositive where the limited intercalation chemistry is avoided. Li-air batteries are suitable for the development of the new generation of EVs. It is estimated that a well optimized Li-air battery can yield a specific energy of up to 3000 Wh/Kg, over a factor of 15 greater than the state of the art lithium ion batteries. Electrical cars today typically can travel only about 150 km on current LIB technology. The development of the lithium air batteries stands chance of being light enough to travel 800 km on a single charge and cheap enough to be practical for a typical family car. This problem is creating a significant barrier to electric vehicle adoption. However, the impact of this technology has so far fallen short of its potential due to several daunting challenges which must be overcome as the cyclability or the wide gap between the practical (362 Wh/kg) and the theoretical (11 kWh/g) values of the specific energy.

  10. Evaluation Framework for Alternative Fuel Vehicles: Sustainable Development Perspective

    Directory of Open Access Journals (Sweden)

    Dong-Shang Chang

    2015-08-01

    Full Text Available Road transport accounts for 72.06% of total transport CO2, which is considered a cause of climate change. At present, the use of alternative fuels has become a pressing issue and a significant number of automakers and scholars have devoted themselves to the study and subsequent development of alternative fuel vehicles (AFVs. The evaluation of AFVs should consider not only air pollution reduction and fuel efficiency but also AFV sustainability. In general, the field of sustainable development is subdivided into three areas: economic, environmental, and social. On the basis of the sustainable development perspective, this study presents an evaluation framework for AFVs by using the DEMATEL-based analytical network process. The results reveal that the five most important criteria are price, added value, user acceptance, reduction of hazardous substances, and dematerialization. Price is the most important criterion because it can improve the popularity of AFVs and affect other criteria, including user acceptance. Additional, the energy usage criterion is expected to significantly affect the sustainable development of AFVs. These results should be seriously considered by automakers and governments in developing AFVs.

  11. Design of limited-stop service based on the degree of unbalance of passenger demand

    Science.gov (United States)

    2018-01-01

    This paper presents a limited-stop service for a bus fleet to meet the unbalanced demand of passengers on a bus route and to improve the transit service of the bus route. This strategy includes two parts: a degree assessment of unbalanced passenger demand and an optimization of the limited-stop service. The degree assessment of unbalanced passenger demand, which is based on the different passenger demand between stations and the unbalance of passengers within the station, is used to judge whether implementing the limited-stop service is necessary for a bus route. The optimization of limited-stop service considers the influence of stop skipping action and bus capacity on the left-over passengers to determine the proper skipping stations for the bus fleet serving the entire route by minimizing both the waiting time and in-vehicle time of passengers and the running time of vehicles. A solution algorithm based on genetic algorithm is also presented to evaluate the degree of unbalanced passenger demand and optimize the limited-stop scheme. Then, the proper strategy is tested on a bus route in Changchun city of China. The threshold of degree assessment of unbalanced passenger demand can be calibrated and adapted to different passenger demands. PMID:29505585

  12. Design of limited-stop service based on the degree of unbalance of passenger demand.

    Science.gov (United States)

    Zhang, Hu; Zhao, Shuzhi; Liu, Huasheng; Liang, Shidong

    2018-01-01

    This paper presents a limited-stop service for a bus fleet to meet the unbalanced demand of passengers on a bus route and to improve the transit service of the bus route. This strategy includes two parts: a degree assessment of unbalanced passenger demand and an optimization of the limited-stop service. The degree assessment of unbalanced passenger demand, which is based on the different passenger demand between stations and the unbalance of passengers within the station, is used to judge whether implementing the limited-stop service is necessary for a bus route. The optimization of limited-stop service considers the influence of stop skipping action and bus capacity on the left-over passengers to determine the proper skipping stations for the bus fleet serving the entire route by minimizing both the waiting time and in-vehicle time of passengers and the running time of vehicles. A solution algorithm based on genetic algorithm is also presented to evaluate the degree of unbalanced passenger demand and optimize the limited-stop scheme. Then, the proper strategy is tested on a bus route in Changchun city of China. The threshold of degree assessment of unbalanced passenger demand can be calibrated and adapted to different passenger demands.

  13. Simulating the impact of policy, energy prices and technological progress on the passenger car fleet in Austria-A model based analysis 2010-2050

    International Nuclear Information System (INIS)

    Kloess, Maximilian; Mueller, Andreas

    2011-01-01

    This paper investigates the effects of policy, fuel prices and technological progress on the Austrian passenger car fleet in terms of energy consumption and greenhouse gas (GHG) emissions. To analyse these effects a simulation model is used. We model the car fleet from a bottom-up perspective, with a detailed coverage of vehicle specifications and propulsion technologies. The model focuses on the technological trend toward electrified propulsion systems and their potential effects on the fleet's energy consumption and GHG emissions. To represent the impact of prices and income on the development of the fleet, we combine the fleet model with top-down demand models. We developed two scenarios for the time frame 2010-2050, using two different sets of assumptions for regulatory development and conditions of increasing fossil fuel prices and continuous technological progress in vehicle propulsion technologies. The results indicate that material cuts in energy consumption and GHG emissions can be achieved with changes to the political framework for passenger cars. Appropriate taxation of fuels and cars can stabilise demand for individual motorised transport and lead to an improvement in vehicle efficiency by fostering the adoption of efficient vehicle propulsion technologies and low carbon fuels. - Highlights: → We present a simulation model for future energy demand and greenhouse gas emissions in passenger car transport. → We develop scenarios up to 2050 assuming two different policy schemes. → Policy strongly affects energy demand and greenhouse gas emissions in passenger car transport. → Policy can slow down growth in demand for passenger car transport. → Policy can promote the diffusion of more efficient propulsion technologies and low carbon fuels.

  14. Panorama 2011: The development of hybrid and electric vehicles

    International Nuclear Information System (INIS)

    Vinot, S.

    2011-01-01

    Car manufacturers are having to deal with increasingly stringent norms and customers who are increasingly demanding with respect to fuel savings. As a result, large numbers of them are now looking into solutions that involve electrifying their vehicles. Hybrid vehicles, some of which can be recharged, and electric vehicles are the new stars of the auto trade shows. But not all manufacturers are necessarily using the same strategies. (author)

  15. 76 FR 77716 - Alternate Passenger Rail Service Pilot Program

    Science.gov (United States)

    2011-12-14

    ...-0108; Notice No. 2] RIN 2130-AC19 Alternate Passenger Rail Service Pilot Program AGENCY: Federal... rule is in response to a statutory mandate that FRA complete a rulemaking proceeding to develop a pilot... enactment of the Passenger Rail Investment and Improvement Act of 2008. The final rule develops this pilot...

  16. Bantam: A Systematic Approach to Reusable Launch Vehicle Technology Development

    Science.gov (United States)

    Griner, Carolyn; Lyles, Garry

    1999-01-01

    The Bantam technology project is focused on providing a low cost launch capability for very small (100 kilogram) NASA and University science payloads. The cost goal has been set at one million dollars per launch. The Bantam project, however, represents much more than a small payload launch capability. Bantam represents a unique, systematic approach to reusable launch vehicle technology development. This technology maturation approach will enable future highly reusable launch concepts in any payload class. These launch vehicle concepts of the future could deliver payloads for hundreds of dollars per pound, enabling dramatic growth in civil and commercial space enterprise. The National Aeronautics and Space Administration (NASA) has demonstrated a better, faster, and cheaper approach to science discovery in recent years. This approach is exemplified by the successful Mars Exploration Program lead by the Jet Propulsion Laboratory (JPL) for the NASA Space Science Enterprise. The Bantam project represents an approach to space transportation technology maturation that is very similar to the Mars Exploration Program. The NASA Advanced Space Transportation Program (ASTP) and Future X Pathfinder Program will combine to systematically mature reusable space transportation technology from low technology readiness to system level flight demonstration. New reusable space transportation capability will be demonstrated at a small (Bantam) scale approximately every two years. Each flight demonstration will build on the knowledge derived from the previous flight tests. The Bantam scale flight demonstrations will begin with the flights of the X-34. The X-34 will demonstrate reusable launch vehicle technologies including; flight regimes up to Mach 8 and 250,000 feet, autonomous flight operations, all weather operations, twenty-five flights in one year with a surge capability of two flights in less than twenty-four hours and safe abort. The Bantam project will build on this initial

  17. Ansaldo programs on fuel cell vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Marcenaro, B.G.; Federici, F. [Ansaldo Ricerche Srl, Genova (Italy)

    1996-12-31

    The growth in traffic and the importance of maintaining a stable ecology at the global scale, particularly with regard to atmospheric pollution, raises the necessity to realize a new generation of vehicles which are more efficient, more economical and compatible with the environment. At European level, the Car of Tomorrow task force has identified fuel cells as a promising alternative propulsion system. Ansaldo Ricerche has been involved in the development of fuel cell vehicles since the early nineties. Current ongoing programs relates to: (1) Fuel cell bus demonstrator (EQHEPP BUS) Test in 1996 (2) Fuel cell boat demonstrator (EQHHPP BOAT) Test in 1997 (3) Fuel cell passenger car prototype (FEVER) Test in 1997 (4) 2nd generation Fuel cell bus (FCBUS) 1996-1999 (5) 2nd generation Fuel cell passenger car (HYDRO-GEN) 1996-1999.

  18. Ejection of a rear facing, golf cart passenger.

    Science.gov (United States)

    Schau, Kyle; Masory, Oren

    2013-10-01

    The following report details the findings of a series of experiments and simulations performed on a commercially available, shuttle style golf cart during several maneuvers involving rapid accelerations of the vehicle. It is determined that the current set of passive restraints on these types of golf carts are not adequate in preventing ejection of a rear facing passenger during rapid accelerations in the forward and lateral directions. Experimental data and simulations show that a hip restraint must be a minimum of 13 in. above the seat in order to secure a rear facing passenger during sharp turns, compared to the current restraint height of 5 in. Furthermore, it is determined that a restraint directly in front of the rear facing passenger is necessary to prevent ejection. In addressing these issues, golf cart manufacturers could greatly reduce the likelihood of injury due to ejection of a rear facing, golf cart passenger. Copyright © 2013 Elsevier Ltd. All rights reserved.

  19. Forecasting of passenger traffic in Moscow metro applying artificial neural networks

    International Nuclear Information System (INIS)

    Ivanov, V.V.; Natsional'nyj Issledovatel'skij Yadernyj Univ. MIFI, Moscow; FKU Rostransmodernizatsiya, Moscow

    2016-01-01

    Methods for the forecasting of passenger traffic in Moscow metro have been developed using artificial neural networks. To this end, the factors primarily determining passenger traffic in the subway have been analyzed and selected [ru

  20. Evaluating the development of life and progress of heavy vehicles ...

    African Journals Online (AJOL)

    Regarding the investigation of new technologies, we have to think to make changes in vehicle technology or finding alternative technology. According to the first priority, criteria and the weight of analytic hierarchy process, the technical criteria, first the action should be done in technical improvements of the vehicle, and also ...

  1. Commercial Electric Vehicle (EV) Development and Manufacturing Program

    Energy Technology Data Exchange (ETDEWEB)

    Leeve, Dion

    2014-06-30

    Navistar with the Department of Energy’s assistance undertook this effort to achieve the project objectives as listed in the next section. A wholly owned subsidiary of Navistar, Workhorse Sales Corporation was the original grant awardee and upon their discontinuation as a standalone business entity, Navistar assumed the role of principal investigator. The intent of the effort, as part of the American Recovery and Reinvestment Act (ARRA) was to produce zero emission vehicles that could meet the needs of the marketplace while reducing carbon emissions to zero. This effort was predicated upon the assumption that concurrent development activities in the lithium ion battery industry investigations would significantly increase their production volumes thus leading to substantial reductions in their manufacturing costs. As a result of this development effort much was learned about the overall system compatibility between the electric motor, battery pack, and charging capabilities. The original system was significantly revised and improved during the execution of this development effort. The overall approach that was chosen was to utilize a British zero emissions, class 2 truck that had been developed for their market, homologate it and modify it to meet the product requirements as specified in the grant details. All of these specific goals were achieved. During the course of marketing and selling the product valuable information was obtained as relates to customer expectations, price points, and product performance expectations, specifically those customer expectations about range requirements in urban delivery situations. While the grant requirements specified a range of 100 miles on a single charge, actual customer usage logs indicate a range of 40 miles or less is typical for their applications. The price point, primarily due to battery pack costs, was significantly higher than the mass market could bear. From Navistar’s and the overall industry’s perspective

  2. Potential vehicle fleet CO2 reductions and cost implications for various vehicle technology deployment scenarios in Europe

    International Nuclear Information System (INIS)

    Pasaoglu, Guzay; Honselaar, Michel; Thiel, Christian

    2012-01-01

    The continuous rise in demand for road transportation has a significant effect on Europe's oil dependency and emissions of greenhouse gases. Alternative fuels and vehicle technology can mitigate these effects. This study analyses power-train deployment scenarios for passenger cars and light commercial vehicles in EU-27 until 2050. It considers European policy developments on vehicle CO 2 emissions, bio-energy mandates and reductions in the CO 2 footprint of the European energy mix and translates these into comprehensive scenarios for the road transport sector. It quantifies and assesses the potential impact of these scenarios on well-to-wheel (WtW) CO 2 emission reductions primary energy demand evolution, and cost aspects for the prospective vehicle owners. The study reveals that, under the deployed scenarios, the use of bio-fuel blends, technological learning and the deployment of hybrids, battery electric, plug-in hybrid and fuel cell vehicles can decrease WtW CO 2 emissions in EU-27 passenger road transport by 35–57% (compared to 2010 levels) and primary energy demand by 29–51 Mtoe as they would benefit from a future assumed decarbonised electricity and hydrogen mix in Europe. Learning effects can lead to acceptable payback periods for vehicle owners of electric drive vehicles. - Highlights: ► Power-train penetration scenarios for 2010–2050 passenger road transport in Europe. ► A dedicated tool is developed to analyse H 2 production and distribution mix till 2050. ► Alternative vehicles can drastically reduce CO 2 emissions and energy demand. ► Electric vehicles could become cost competitive to conventional vehicles by 2030. ► Policies needed to create adequate momentum and guarantee decarbonised transport.

  3. Development of automatic air intake door control system for exhaust gas. Prevention of contaminated air by controlling A/C air intake door; Haiki gas taio auto naigaiki system no kaihatsu. Eakon suikomiguchi seigyo ni yoru haiki gas no shashitsunai eno shinnyu boshi

    Energy Technology Data Exchange (ETDEWEB)

    Honda, Y; Samukawa, K [Denso Corp., Aichi (Japan)

    1997-10-01

    Thermal comfort in the cabin of vehicle is upgraded by developing the climate control system Passengers must control the intake door of air conditioner to reduce entering Exhaust Gas into the cabin. This paper is concerned with development the automatic intake door control system to acquire high comfort performance of passengers. 8 figs., 1 tab.

  4. Assessing community child passenger safety efforts in three Northwest Tribes.

    Science.gov (United States)

    Smith, M L; Berger, L R

    2002-12-01

    To identify strengths and weaknesses in community based child passenger safety programs by developing a scoring instrument and conducting observations of child restraint use in three Native American communities. The three communities are autonomous Tribal reservations in the Pacific Northwest. Their per capita incomes and rates of unemployment are comparable. In each community, 100 children under 5 years old were observed for car seat use. A six item community assessment tool (100 points maximum) awarded points for such items as the type (primary or secondary) and enforcement of child restraint laws; availability of car seats from distribution programs; extent of educational programs; and access to data on vehicle injuries. For children from birth to 4 years, the car seat use rate ranged from 12%-21%. Rates for infants (71%-80%) far exceeded rates for 1-4 year old children (5%-14%). Community scores ranged from 0 to 31.5 points. There was no correlation between scores and observed car seat use. One reason was the total lack of enforcement of restraint laws. A community assessment tool can highlight weaknesses in child passenger efforts. Linking such a tool with an objective measure of impact can be applied to other injury problems, such as fire safety or domestic violence. The very process of creating and implementing a community assessment can enhance agency collaboration and publicize evidence based "best practices" for injury prevention. Further study is needed to address methodologic issues and to examine crash and medical data in relation to community child passenger safety scores.

  5. Development of "Remotely Operated Vehicles for Education and Research" (ROVERs)

    Science.gov (United States)

    Gaines, J. E.; Bland, G.; Bydlowski, D.

    2017-12-01

    The University of South Florida is a team member for the AREN project which develops educational technologies for data acquisition. "Remotely Operated Vehicles for Education and Research" (ROVERs) are floatable data acquisition systems used for Earth science measurements. The USF partnership was productive in the first year, resulting in new autonomous ROVER platforms being developed and used during a 5 week STEM summer camp by middle school youth. ROVERs were outfitted with GPS and temperature sensors and programmed to move forward, backwards, and to turn autonomously using the National Instruments myRIO embedded system. GLOBE protocols were used to collect data. The outreach program's structure lended itself to accomplishing an essential development effort for the AREN project towards the use of the ROVER platform in informal educational settings. A primary objective of the partnership is curriculum development to integrate GLOBE protocols and NASA technology and hardware/ROVER development wher new ROVER platforms are explored. The USF partnership resulted in two design prototypes for ROVERs, both of which can be created from recyclable materials for flotation and either 3D printed or laser cut components. In addition, both use the National Instruments myRIO for autonomous control. We will present two prototypes designed for use during the USF outreach program, the structure of the program, and details on the fabrication of prototype Z during the program by middle school students. Considering the 5-year objective of the AREN project is to "develop approaches, learning plans, and specific tools that can be affordably implemented nationwide (globally)", the USF partnership is key as it contributes to each part of the objective in a unique and impactful way.

  6. Developments in batteries and fuel cells for electric and hybrid electric vehicles

    International Nuclear Information System (INIS)

    Ahmed, R.

    2013-01-01

    Due to ever increasing threats of climate change, urban air pollution and costly and depleting oil and gas sources a lot of work is being done for the development of electric vehicles. Hybrid electric vehicles, plug-in hybrid electric vehicles and all electric vehicles are powered by batteries or by hydrogen and fuel cells are the main types of vehicles being developed. Main types of batteries which can be used for electric vehicles are lead-acid, Ni-Cd, Nickel-Metal-Hybrid ( NiMH) and Lithium-ion (Li-ion) batteries which are discussed and compared. Lithium ion battery is the mostly used battery. Developments in the lithium ion batteries are discussed and reviewed. Redox flow batteries are also potential candidates for electric vehicles and are described. Hybrid electric vehicles can reduce fuel consumption considerably and is a good midterm solution. Electric and hybrid electric vehicles are discussed. Electric vehicles are necessary to mitigate the effects of pollution and dependence on oil. For all the electric vehicles there are two options: batteries and fuel Cells. Batteries are useful for small vehicles and shorter distances but for vehicle range greater than 150 km fuel cells are superior to batteries in terms of cost, efficiency and durability even using natural gas and other fuels in addition to hydrogen. Ultimate solution for electric vehicles are hydrogen and fuel cells and this opinion is also shared by most of the automobile manufacturers. Developments in fuel cells and their applications for automobiles are described and reviewed. Comparisons have been done in the literature between batteries and fuel cells and are described. (author)

  7. Hybrid Turbine Electric Vehicle

    Science.gov (United States)

    Viterna, Larry A.

    1997-01-01

    Hybrid electric power trains may revolutionize today's ground passenger vehicles by significantly improving fuel economy and decreasing emissions. The NASA Lewis Research Center is working with industry, universities, and Government to develop and demonstrate a hybrid electric vehicle. Our partners include Bowling Green State University, the Cleveland Regional Transit Authority, Lincoln Electric Motor Division, the State of Ohio's Department of Development, and Teledyne Ryan Aeronautical. The vehicle will be a heavy class urban transit bus offering double the fuel economy of today's buses and emissions that are reduced to 1/10th of the Environmental Protection Agency's standards. At the heart of the vehicle's drive train is a natural-gas-fueled engine. Initially, a small automotive engine will be tested as a baseline. This will be followed by the introduction of an advanced gas turbine developed from an aircraft jet engine. The engine turns a high-speed generator, producing electricity. Power from both the generator and an onboard energy storage system is then provided to a variable-speed electric motor attached to the rear drive axle. An intelligent power-control system determines the most efficient operation of the engine and energy storage system.

  8. Distributed Control in Multi-Vehicle Systems

    Directory of Open Access Journals (Sweden)

    Paul A. Avery

    2013-12-01

    Full Text Available The Southwest Research Institute (SwRI Mobile Autonomous Robotics Technology Initiative (MARTI program has enabled the development of fully-autonomous passenger-sized commercial vehicles and military tactical vehicles, as well as the development of cooperative vehicle behaviors, such as cooperative sensor sharing and cooperative convoy operations. The program has also developed behaviors to interface intelligent vehicles with intelligent road-side devices. The development of intelligent vehicle behaviors cannot be approached as stand-alone phenomena; rather, they must be understood within a context of the broader traffic system dynamics. The study of other complex systems has shown that system-level behaviors emerge as a result of the spatio-temporal dynamics within a system's constituent parts. The design of such systems must therefore account for both the system-level emergent behavior, as well as behaviors of individuals within the system. It has also become clear over the past several years, for both of these domains, that human trust in the behavior of individual vehicles is paramount to broader technology adoption. This paper examines the interplay between individual vehicle capabilities, vehicle connectivity, and emergent system behaviors, and presents some considerations for a distributed control paradigm in a multi-vehicle system.

  9. World-wide developments in motor vehicle inspection/maintenance (I/M) programs

    Energy Technology Data Exchange (ETDEWEB)

    Klausmeier, R. [Consulting Inc., Austin, TX (United States); Kishan, S. [Radian Corporation, Austin, TX (United States)

    1995-12-31

    Motor vehicles contribute much to urban air pollution. As a result, most governments have enacted emission standards that significantly lower pollutant emission levels from new motor vehicles. For example, vehicles built in the United States emit 95 % fewer pollutants than uncontrolled vehicles when they are new. However, studies indicate that proper maintenance is needed to obtain the full benefit of vehicle emission controls. Furthermore, there is evidence that a significant percentage of the vehicle fleet is not properly maintained. This has led to the creation of motor vehicle Inspection/Maintenance (I/M) Programs. I/M programs inspect vehicles for indications that they are emitting excessive quantities of pollutants. Vehicles that fail the inspection must be repaired in order to comply with program requirements. The first I/M programs were implemented in the United States in the early 1970s. With substantial urging from the federal government, most of the U.S. states with severe air pollution problems have implemented I/M programs. Recently, with the passage of the U.S. Clean Air Act Amendments of 1990, many states have been required to significantly upgrade the performance and coverage of their I/M programs. I/M programs also have been implemented in Europe and recently in Asia. This presentation reviews developments in I/M programs for light-duty gasoline powered vehicles. Developments in I/M programs for diesel powered vehicles are briefly described. (author)

  10. World-wide developments in motor vehicle inspection/maintenance (I/M) programs

    Energy Technology Data Exchange (ETDEWEB)

    Klausmeier, R [Consulting Inc., Austin, TX (United States); Kishan, S [Radian Corporation, Austin, TX (United States)

    1996-12-31

    Motor vehicles contribute much to urban air pollution. As a result, most governments have enacted emission standards that significantly lower pollutant emission levels from new motor vehicles. For example, vehicles built in the United States emit 95 % fewer pollutants than uncontrolled vehicles when they are new. However, studies indicate that proper maintenance is needed to obtain the full benefit of vehicle emission controls. Furthermore, there is evidence that a significant percentage of the vehicle fleet is not properly maintained. This has led to the creation of motor vehicle Inspection/Maintenance (I/M) Programs. I/M programs inspect vehicles for indications that they are emitting excessive quantities of pollutants. Vehicles that fail the inspection must be repaired in order to comply with program requirements. The first I/M programs were implemented in the United States in the early 1970s. With substantial urging from the federal government, most of the U.S. states with severe air pollution problems have implemented I/M programs. Recently, with the passage of the U.S. Clean Air Act Amendments of 1990, many states have been required to significantly upgrade the performance and coverage of their I/M programs. I/M programs also have been implemented in Europe and recently in Asia. This presentation reviews developments in I/M programs for light-duty gasoline powered vehicles. Developments in I/M programs for diesel powered vehicles are briefly described. (author)

  11. ON PROBABILITY FUNCTION OF TRIP ROUTE CHOICE IN PASSENGER TRANSPORT SYSTEM OF CITIES

    Directory of Open Access Journals (Sweden)

    N. Nefedof

    2014-02-01

    Full Text Available The results of statistical processing of experimental research data in Kharkiv, aimed at determining the relation between the passenger trip choice probability and the actual vehicles waiting time at bus terminals are presented.

  12. Sound design for diesel passenger cars

    Energy Technology Data Exchange (ETDEWEB)

    Belluscio, Michele; Ruotolo, Romualdo [GM Powertrain Europe, Torino (Italy); Schoenherr, Christian; Schuster, Guenter [GM Europe, Ruesselsheim (Germany); Eisele, Georg; Genender, Peter; Wolff, Klaus; Van Keymeulen, Johan [FEV Motorentechnik GmbH, Aachen (Germany)

    2008-07-01

    With the growing market contribution of diesel passenger cars in Europe, it becomes more important to create a brand and market segment specific vehicle sound. Beside the usually considered pleasantness related topics like diesel knocking and high noise excitation, it is important to fulfil also the requirements regarding a dynamic vehicle impression. This impression is mainly influenced by the load dependency of the engine induced noise, which is reduced for diesel engines due to the missing throttle valve and the damping effect of the turbocharger and the diesel particulate filter. By means of a detailed noise transfer path analysis the contribution with dynamic potential can be identified. Furthermore the load dependency itself of a certain noise contribution can be strengthened, which allows for a dynamic sound character comparable to sporty gasoline vehicles. (orig.)

  13. Linear engine development for series hybrid electric vehicles

    Science.gov (United States)

    Toth-Nagy, Csaba

    This dissertation argues that diminishing oil reserves, concern over global climate change, and desire to improve ambient air quality all demand the development of environment-friendly personal transportation. In certain applications, series hybrid electric vehicles offer an attractive solution to reducing fuel consumption and emissions. Furthermore, linear engines are emerging as a powerplant suited to series HEV applications. In this dissertation, a linear engine/alternator was considered as the auxiliary power unit of a range extender series hybrid electric vehicle. A prototype linear engine/alternator was developed, constructed and tested at West Virginia University. The engine was a 2-stroke, 2-cylinder, dual piston, direct injection, diesel engine. Experiment on the engine was performed to study its behavior. The study variables included mass of the translator, amount of fuel injected, injection timing, load, and stroke with operating frequency and mechanical efficiency as the basis of comparison. The linear engine was analyzed in detail and a simple simulation model was constructed to compare the trends of simulation with the experimental data and to expand on the area where the experimental data were lacking. The simulation was based on a simple and analytical model, rather than a detailed and intensely numerical one. The experimental and theoretical data showed similar trends. Increasing translator mass decreased the operating frequency and increased compression ratio. Larger mass and increased compression ratio improved the ability of the engine to sustain operation and the engine was able to idle on less fuel injected into the cylinder. Increasing the stroke length caused the operating frequency to drop. Increasing fueling or decreasing the load resulted in increased operating frequency. This projects the possibility of using the operating frequency as an input for feedback control of the engine. Injection timing was varied to investigate two different

  14. Computation of thermal comfort inside a passenger car compartment

    International Nuclear Information System (INIS)

    Mezrhab, A.; Bouzidi, M.

    2006-01-01

    This paper describes a numerical model to study the behaviour of thermal comfort inside the passenger car compartment according to climatic conditions and materials that compose the vehicle. The specifically developed numerical model is based on the nodal method and the finite difference method. Its specificities are: (i) the transient mode, (ii) the taking into account of the combined convection, conduction and radiation heat transfer, (iii) the coupling of two spectral bands (short-wave and long-wave radiation) and two solar fluxes (beam and diffuse). The compartment is subdivided in several solid nodes (materials constituting the compartment) and fluid nodes (volumes of air inside the compartment). The establishment of the heat balance for each node gives the evolution of its temperature. Effects of solar radiation, types of glazing, car colour and radiative properties of materials constituting the compartment are investigated

  15. Developing Computational Fluid Dynamics (CFD Models to Evaluate Available Energy in Exhaust Systems of Diesel Light-Duty Vehicles

    Directory of Open Access Journals (Sweden)

    Pablo Fernández-Yáñez

    2017-06-01

    Full Text Available Around a third of the energy input in an automotive engine is wasted through the exhaust system. Since numerous technologies to harvest energy from exhaust gases are accessible, it is of great interest to find time- and cost-efficient methods to evaluate available thermal energy under different engine conditions. Computational fluid dynamics (CFD is becoming a very valuable tool for numerical predictions of exhaust flows. In this work, a methodology to build a simple three-dimensional (3D model of the exhaust system of automotive internal combustion engines (ICE was developed. Experimental data of exhaust gas in the most used part of the engine map in passenger diesel vehicles were employed as input for calculations. Sensitivity analyses of different numeric schemes have been conducted in order to attain accurate results. The model built allows for obtaining details on temperature and pressure fields along the exhaust system, and for complementing the experimental results for a better understanding of the flow phenomena and heat transfer through the system for further energy recovery devices.

  16. Influence of the seasonal factor on the long-distance passenger correspondence

    Directory of Open Access Journals (Sweden)

    K. Dolia

    2017-12-01

    Full Text Available Up-today intercity passenger transportation is needed to consider fluctuations in demand for services over time. Designated fluctuations in demand mainly linked to the onset of a period of national or religious celebrations holidays, mass vacation in summer, internal and international sports and cultural activities, ect. Therefore, these demand irregularity of using public intercity transport should be considered when managing transportation. In issue to meet the needs of passengers moving within existing fluctuations in demand can decide to change the parameters of the components of the transport system. These changes include variety in amount or type of vehicles, schedules, changes in traffic patterns routes, introduction of these routes, limiting of the passenger’s purchasing ability fares and so on. It is important to determine the passenger’s place in the social, economic or cultural development of the population overemphasized. Therefore, regulation of activity of the public transport services must satisfy the possibility of these services within acceptable financial, time and physical burden for passengers. So, component optimization efficiency of intercity passengers’ transportation should take place in harmony with the social and economic development of society. The requirements set out not to satisfy the demand of passengers to move through extra large fare, lack of communication between bus transport areas with constant correspondence, failure to comply with increasing comfort haulage transport of tiredness or lack of means of transport are unacceptable phenomena. On the one hand the importance of the social dimension in long-distance traffic route of transport. In accordance with the meaning specified the need for balanced decision-making on the management system of passenger traffic. Invention compromise between technical and economic level to meet the demand and requirements of the conservation of expenditure

  17. Evolutional development of controlling software for agricultural vehicles and robots

    DEFF Research Database (Denmark)

    Nakanishi, Tsuneo; Jæger-Hansen, Claes Lund; Griepentrog, Hans-Werner

    Agricultural vehicles and robots expand their controlling software in size and complexity for their increasing functions. Due to repeated, ad hoc addition and modification, software gets structurally corrupted and becomes low performing, resource consuming and unreliable. This paper presents...

  18. Developing Markets for Zero-Emission Vehicles in Goods Movement

    Science.gov (United States)

    2018-03-01

    This report evaluates the market status and potential freight market penetration of zero emission vehicles (ZEVs) and near ZEVs in the medium and heavy duty class within the California market. It evaluates alternative technologies, primarily battery ...

  19. Drivers' attitudes toward front or rear child passenger belt use and seat belt reminders at these seating positions.

    Science.gov (United States)

    Kidd, David G; McCartt, Anne T

    2014-01-01

    Passengers, especially those in rear seating positions, use seat belts less frequently than drivers. In-vehicle technology can inform drivers when their passengers are unbuckled and encourage passengers to use belts. The current study collected information about drivers' attitudes toward passenger belt use and belt reminders for front passengers and children in back seats. A national telephone survey of 1218 people 18 and older was conducted, of which 477 respondents were drivers who transport a front seat passenger at least once a week and 254 were drivers who transport an 8- to 15-year-old child in the back seat. Respondents were asked about their attitudes toward belt use by their front passengers or rear child passengers and preferences for different passenger belt reminder features. Ninety percent of drivers who regularly transport front seat passengers said that the passengers always use seat belts. Reported belt use was even higher among 8- to 15-year-old children in the back seat (97%). Among the drivers whose children do not always buckle up, about half said their child unbuckled the belt during the trip. Almost every full-time belt use driver (96%) would encourage front passengers to buckle up if not belted, compared to 57 percent of part-time belt users and nonusers. In contrast, nearly every driver who transports children in the back seat would encourage their belt use, regardless of the driver's belt use habits. Most drivers who transport front passengers wanted passenger belt reminders to encourage passengers to buckle up. Most of these drivers wanted a chime/buzzer or warning light or text display and wanted the reminder to last indefinitely. Most drivers who transport child passengers in the rear seat wanted the vehicle to indicate whether child passengers are unbuckled. A large majority of these drivers wanted notifications via a visual diagram of seating positions and belt use, a chime/buzzer, and a warning light or text display. These drivers

  20. Vibration Isolation for Parallel Hydraulic Hybrid Vehicles

    Directory of Open Access Journals (Sweden)

    The M. Nguyen

    2008-01-01

    Full Text Available In recent decades, several types of hybrid vehicles have been developed in order to improve the fuel economy and to reduce the pollution. Hybrid electric vehicles (HEV have shown a significant improvement in fuel efficiency for small and medium-sized passenger vehicles and SUVs. HEV has several limitations when applied to heavy vehicles; one is that larger vehicles demand more power, which requires significantly larger battery capacities. As an alternative solution, hydraulic hybrid technology has been found effective for heavy duty vehicle because of its high power density. The mechanical batteries used in hydraulic hybrid vehicles (HHV can be charged and discharged remarkably faster than chemical batteries. This feature is essential for heavy vehicle hybridization. One of the main problems that should be solved for the successful commercialization of HHV is the excessive noise and vibration involving with the hydraulic systems. This study focuses on using magnetorheological (MR technology to reduce the noise and vibration transmissibility from the hydraulic system to the vehicle body. In order to study the noise and vibration of HHV, a hydraulic hybrid subsystem in parallel design is analyzed. This research shows that the MR elements play an important role in reducing the transmitted noise and vibration to the vehicle body. Additionally, locations and orientations of the isolation system also affect the efficiency of the noise and vibration mitigation. In simulations, a skyhook control algorithm is used to achieve the highest possible effectiveness of the MR isolation system.

  1. Simulation Development and Analysis of Crew Vehicle Ascent Abort

    Science.gov (United States)

    Wong, Chi S.

    2016-01-01

    NASA's Commercial Crew Program is an integral step in its journey to Mars as it would expedite development of space technologies and open up partnership with U.S. commercial companies. NASA reviews and independent assessment of Commercial Crew Program is fundamental to its success, and being able to model a commercial crew vehicle in a simulation rather than conduct a live test would be a safer, faster, and less expensive way to assess and certify the capabilities of the vehicle. To this end, my project was to determine the feasibility of using a simulation tool named SOMBAT version 2.0 to model a multiple parachute system for Commercial Crew Program simulation. The main tasks assigned to me were to debug and test the main parachute system model, (capable of simulating one to four main parachute bodies), and to utilize a graphical program to animate the simulation results. To begin tackling the first task, I learned how to use SOMBAT by familiarizing myself with its mechanics and by understanding the methods used to tweak its various parameters and outputs. I then used this new knowledge to set up, run, and analyze many different situations within SOMBAT in order to explore the limitations of the parachute model. Some examples of parameters that I varied include the initial velocity and orientation of the falling capsule, the number of main parachutes, and the location where the parachutes were attached to the capsule. Each parameter changed would give a different output, and in some cases, would expose a bug or limitation in the model. A major bug that I discovered was the inability of the model to handle any number of parachutes other than three. I spent quite some time trying to debug the code logically, but was unable to figure it out until my mentor taught me that digital simulation limitations can occur when some approximations are mistakenly assumed for certain in a physical system. This led me to the realization that unlike in all of the programming classes

  2. Manikin families representing obese airline passengers in the US.

    Science.gov (United States)

    Park, Hanjun; Park, Woojin; Kim, Yongkang

    2014-01-01

    Aircraft passenger spaces designed without proper anthropometric analyses can create serious problems for obese passengers, including: possible denial of boarding, excessive body pressures and contact stresses, postural fixity and related health hazards, and increased risks of emergency evacuation failure. In order to help address the obese passenger's accommodation issues, this study developed male and female manikin families that represent obese US airline passengers. Anthropometric data of obese individuals obtained from the CAESAR anthropometric database were analyzed through PCA-based factor analyses. For each gender, a 99% enclosure cuboid was constructed, and a small set of manikins was defined on the basis of each enclosure cuboid. Digital human models (articulated human figures) representing the manikins were created using a human CAD software program. The manikin families were utilized to develop design recommendations for selected aircraft seat dimensions. The manikin families presented in this study would greatly facilitate anthropometrically accommodating large airline passengers.

  3. An expert fault diagnosis system for vehicle air conditioning product development

    NARCIS (Netherlands)

    Tan, C.F.; Tee, B.T.; Khalil, S.N.; Chen, W.; Rauterberg, G.W.M.

    2015-01-01

    The paper describes the development of the vehicle air-conditioning fault diagnosis system in automotive industries with expert system shell. The main aim of the research is to diagnose the problem of new vehicle air-conditioning system development process and select the most suitable solution to

  4. Virtual Learning Communities as a Vehicle for Workforce Development: A Case Study

    Science.gov (United States)

    Allan, Barbara; Lewis, Dina

    2006-01-01

    Purpose: The purpose of this paper is to explore the benefits and challenges of using a virtual learning community (VLC) as a vehicle for workforce development. This paper argues that VLCs provide a flexible vehicle for workforce development. However, workplace realities may lead to unexpected challenges for participants wanting exploit the…

  5. Life cycle assessment for coordination development of nuclear power and electric vehicle

    International Nuclear Information System (INIS)

    Liu Hong; Wang Yingrong

    2010-01-01

    Energy, environment and climate change have become focus political topics. In this paper, the life cycle assessment for cooperation development of nuclear power and electric vehicle were analyzed from the view of energy efficiency and pollutant emissions. The assessment results show that the pathway of nuclear power coupled with electric vehicle is better than coal electric power coupled with electric vehicle and normal gasoline coupled with internal combustion engine powered vehicle in terms of the environmental and energy characteristics. To charge the electric vehicle, instead of water power station, can safeguard the stable operation of nuclear power station. The results could provide consulted for coordination development of nuclear power, electric vehicle and brain power electric net. (authors)

  6. Logistic system as an essential element of modern organization of railway passenger traffic

    Directory of Open Access Journals (Sweden)

    O.A. Khodoskina

    2012-04-01

    Full Text Available The role and place of passenger transport services in the modern structure of rail transportation is considered. The need for approach to rail passenger transport as a logistics system, which is characterized by a set of parameters corresponding to the concept of logistics system in general and taking into account the peculiarities of railway passenger transportation is determined. The features of formation of such a system, taking into account the generally accepted theoretical approach and the specifics of rail transport are also presented. The concept of logistic system for railway vehicles is given; its overall structure is reviewed. The structure of the particular transport is defined by rail freight and in passenger traffic. Is an example of a mathematical model of the logistics system of rail passenger services on the basis of sets of incoming and outgoing parameters is determined. The structure of technologic process for goods and passenger transportation by rail from the perspective of logistics is characterized.

  7. THE AUTOMATIC SYSTEM’S MODEL OF DECISION-MAKING SUPPORT FOR DISPATCHING CONTROL OF THE CITY PASSENGER TRAFFIC

    Directory of Open Access Journals (Sweden)

    V. A. Lakhno

    2016-04-01

    Full Text Available Purpose. This scientific work considers the further development of mathematical models and algorithms for automatic decision support for dispatching management of the city passenger traffic. Methodology. Systems of dispatching management for the city passenger transport are to provide the carrying out of the routes according schedules with minimal deviations from the planned ones through the using of appropriate control actions. The systems’ algorithm focuses on the selection of control actions that compensate the disturbances. It is proposed to use the index of the waiting time minimum for passengers of buses and taxis at stops as a criterion for evaluating of dispatching control systems work. Findings. Based on the conducted analysis of the research within the existing theory of traffic flow of vehicles, it was proposed the model for the system of dispatching management for urban passenger moving units considering the effect of the most important stochastic factors on the schedule of buses and taxis movement in large cities. The obtained system of equations that models the parameter of movement on the bus routes allows you to assess quickly the influence of disturbing effects on the service quality indicators of passengers and, if necessary, to draw up the optimal schedule. Originality. The authors propose a new model for decision support of dispatching management for the city passenger transport. They take into account the effect of the most important stochastic factors, such as the overflowing buses and taxis, their descent from the lines, delays, deviations from the speed limit on the route, etc., on indicators of service quality, as well as optimizing the schedule. Practical value. The results allow to improve approaches to building models using in the systems of dispatching management of urban bus routes, as well as to improve the selection of control actions for similar systems in large cities of Ukraine.

  8. Developing Autonomous Vehicles That Learn to Navigate by Mimicking Human Behavior

    Science.gov (United States)

    2006-09-28

    navigate in an unstructured environment to a specific target or location. 15. SUBJECT TERMS autonomous vehicles , fuzzy logic, learning behavior...ANSI-Std Z39-18 Developing Autonomous Vehicles That Learn to Navigate by Mimicking Human Behavior FINAL REPORT 9/28/2006 Dean B. Edwards Department...the future, as greater numbers of autonomous vehicles are employed, it is hoped that lower LONG-TERM GOALS Use LAGR (Learning Applied to Ground Robots

  9. Media mix elements affecting brand equity: A study of the Indian passenger car market

    Directory of Open Access Journals (Sweden)

    Tanmay Chattopadhyay

    2010-12-01

    Full Text Available The study develops and empirically tests a model for finding the effect of advertising frequency across different media vehicles towards building brand equity for the passenger car market for first time and repeat buyers. The effect that selected media mix elements had on the dimensions of brand equity was examined. First time buyers are expected to have lower category knowledge than repeat buyers, and are hence expected to behave differently from repeat buyers. Since the knowledge structures of these two groups are expected to be different, it is reasonable to predict that they would process product/brand related information differently and this is corroborated by the results.

  10. Emission characteristics when using bioethanol as a fuel for passenger cars

    International Nuclear Information System (INIS)

    Egebaeck, K.E.; Laurikko, J.; Ryden, C.

    1998-11-01

    In 1991 the Swedish Transport and Communication Research Board (KFB), was asked by the Swedish Government to carry out investigations and field tests in order to demonstrate the possibility of using bioethanol and biogas as automotive fuels. A five-year programme was set up for the investigations and demonstrations and the programme was later extended to a seven-year programme. Despite the fact that most of the work has been directed towards heavy-duty vehicles and especially buses in city traffic some important investigations have been carried out in order to demonstrate the use of bioethanol and biogas in passenger cars. The programme for passenger cars has consisted of running and testing 53 Flexible Fuel Vehicles (FFV), fuelled with bioethanol (E85), a project run by the Swedish Ethanol Development Foundation, and 20 other cars fuelled with biogas, a project carried out by the City of Stockholm's Material Supply Organisation, and sponsored by KFB. For both fleets of vehicles the exhaust emissions have been extensively characterised at a laboratory in Finland owned by the Technical Research Centre of Finland. The aim of this paper is to present some interesting results from the demonstrations of the use of E85 in FFV's and thereby especially focus on the results of the characterisation of both regulated and non-regulated emissions 23 refs, 16 figs, 9 tabs

  11. Emission characteristics when using bioethanol as a fuel for passenger cars

    Energy Technology Data Exchange (ETDEWEB)

    Egebaeck, K.E. [Luleaa Univ. of Technology, (Sweden); Laurikko, J. [Technical Research Centre of Finland, Helsinki (Finland); Ryden, C. [Tima, (Sweden)

    1998-11-01

    In 1991 the Swedish Transport and Communication Research Board (KFB), was asked by the Swedish Government to carry out investigations and field tests in order to demonstrate the possibility of using bioethanol and biogas as automotive fuels. A five-year programme was set up for the investigations and demonstrations and the programme was later extended to a seven-year programme. Despite the fact that most of the work has been directed towards heavy-duty vehicles and especially buses in city traffic some important investigations have been carried out in order to demonstrate the use of bioethanol and biogas in passenger cars. The programme for passenger cars has consisted of running and testing 53 Flexible Fuel Vehicles (FFV), fuelled with bioethanol (E85), a project run by the Swedish Ethanol Development Foundation, and 20 other cars fuelled with biogas, a project carried out by the City of Stockholm`s Material Supply Organisation, and sponsored by KFB. For both fleets of vehicles the exhaust emissions have been extensively characterised at a laboratory in Finland owned by the Technical Research Centre of Finland. The aim of this paper is to present some interesting results from the demonstrations of the use of E85 in FFV`s and thereby especially focus on the results of the characterisation of both regulated and non-regulated emissions 23 refs, 16 figs, 9 tabs

  12. The Impact of Drive Cycles and Auxiliary Power on Passenger Car Fuel Economy

    Directory of Open Access Journals (Sweden)

    Thomas Grube

    2018-04-01

    Full Text Available In view of the advancement of zero emission transportation and current discussions on the reliability of nominal passenger car fuel economy, this article considers the procedure for assessing the potential for reducing the fuel consumption of passenger cars by using electric power to operate them. The analysis compares internal combustion engines, hybrid and fully electric concepts utilizing batteries and fuel cells. The starting point for the newly developed, simulation-based fuel consumption analysis is a longitudinal vehicle model. Mechanical power requirements on the drive side incorporate a large variety of standardized drive cycles to simulate typical patterns of car usage. The power requirements of electric heating and air conditioning are also included in the simulation, as these are especially relevant to electric powertrains. Moreover, on-board grid-load profiles are considered in the assessment. Fuel consumption is optimized by applying concept-specific operating strategies. The results show that the combination of low average driving speed and elevated onboard power requirements have severe impacts on the fuel efficiency of all powertrain configurations analyzed. In particular, the operational range of battery-electric vehicles is strongly affected by this due to the limited storage capacity of today’s batteries. The analysis confirms the significance of considering different load patterns of vehicle usage related to driving profiles and onboard electrical and thermal loads.

  13. Ways to improve the environmental conditions of their buses in operation on passenger routes of cities

    Directory of Open Access Journals (Sweden)

    Melnychuk S.V.

    2017-04-01

    Full Text Available The results of studies on operational and environmental parameters buses used on bus routes Zhitomir city. It uses statistical methods for determining the intensity of traffic, passenger traffic and ecology in traffic. To assess the environmental chosen stop with the greatest intensity of traffic, which is the probability of accumulation of pollution transport emissions that exceed permissible limits. Calculation of environmental pollution emission route for vehicles made stops street «Str. Hundreds of Heaven» «CUM», «vul. Hlibna» on the main trunk street Kievska. Results obtained environmental field experiments compared with the data defined calculation methods, based on the proposed use appropriate operational vehicles. The conclusions that indicate the seriousness of the problem and the urgency to address it. The system of environmental safety and road safety in Zhitomir requires significant improvements due to the increased quantities bus vehicles plying city routes. Recommendations to improve the ecological condition of intersections can be developed through the optimization of traffic using buses with environmentally improved operating parameters. Keywords: environmental and operational parameters; ecological safety; environmental assessment; intensity of traffic; passenger traffic; environmental conditions; operation; bus choice; stop.

  14. Sustainable mobility. Sustainable development and the passenger transportation facilities structure in the Randstad, Netherlands; Duurzame mobiliteit. Duurzame ontwikkeling en de voorzieningenstructuur van het personenvervoer in de Randstad

    Energy Technology Data Exchange (ETDEWEB)

    Baggen, J.

    1994-06-23

    The environmental problems in the Netherlands and the necessity of a sustainable development are outlined in chapter 1. Sustainable development is situated and studied in the area of tension of environment/ecology and economy. Sustainable mobility is located in the area of tension between amenity and accessibility. In chapter 2 a conceptual framework is created to indicate ways that result in a lasting compatibility of (car)mobility with both physical environment and social-economic development. In chapter 3 instruments are chosen for the empirical part of this study: reduction of unwanted car mobility by construction of alternative infrastructure (public transport) in combination with a reduction (prevention) of mobility needs by means of physical planning. A theoretical system description of transport systems in their spatial and regional-economic context is given, resulting in a layout for present and future transport systems, based on transport mode (private and public transport), function (main route or feeder) and spatial level (from international to local). In chapter 4 spatial levels are the basis for a description and analysis of developments and policy in the fields of physical planning, transport and environment. Chapter 6 gives a description and an analysis of present facilities structures and their effects on amenity in the area of study. In chapter 7 a number of land-use scenarios for facilities structures and effects on amenity of passenger transport in future are designed for the Randstad in 2015. These scenarios are chosen on the basis of a number of factors that effect land-use planning: the exogenous effects of demographic developments and endogenous effects of physical planning on future land-use of the study area. A combination of these two factors results in four land-use scenarios. They are mainly supplemented with various configurations of housing locations on the basis of different physical planning principles. (Abstract Truncated)

  15. The development and validation of a thermal model for the cabin of a vehicle

    International Nuclear Information System (INIS)

    Marcos, David; Pino, Francisco J.; Bordons, Carlos; Guerra, José J.

    2014-01-01

    Energy management in modern vehicles is a crucial issue, especially in the case of electric vehicles (EV) or hybrid vehicles (HV), in which different energy sources and loads must be considered for the operation of a vehicle. Air conditioning is an important load that must be thoroughly analysed because it can constitute a considerable percentage of the energy demand. In this paper, a simplified and dynamic thermal model for the cabin of a vehicle is proposed and validated. The developed model can be used for the design and testing of the heating, ventilation, and air conditioning (HVAC) system of a vehicle and for the study of its effects on the performance and fuel consumption of vehicles, such as EVs or HVs. The model is based on theoretical heat transfer, thermal inertia, and radiation treatment equations. The model results obtained from simulations are compared with the cabin air temperature of a vehicle under different conditions. This comparison demonstrates the accuracy between the simulation results and actual results. - Highlights: •A thermal model of a vehicle cabin with two thermal inertias is developed. •The model is validated with experimental data. •The simulation results and the experimental data fit

  16. Selection of the motor train of vehicles of load and passengers service with energy efficiency; Seleccion del tren motriz de vehiculos del servicio de carga y pasajeros con eficiencia energetica

    Energy Technology Data Exchange (ETDEWEB)

    Rafael Morales, Mercedes [Instituto Mexicano del Transporte (MExico)

    2003-07-01

    The companies of motor transport in Mexico are affected in their economy mainly by the low efficiency in the fuel consumption, specially the one dedicated to heavy service. Despite the outpost technology that is becoming available and adopted by the vehicular park to vehicular in relation to the energy efficiency, the cost per transported ton has not diminished in any substantial way. In this paper, a study is presented on the influence that it has within this problem, the selection of the components of the motor train in the fuel consumption and the capacity of ascent of the vehicle in relation to the weight of the transported load. As result of the study was developed in the Mexican Institute of Transport a computer program based on the real tests of performance that a vehicle can be subjected to, taking into consideration the optimum regime of the motor with the minimum fuel consumption. The program helps the carrier to select the most suitable motor train for the vehicle that is intended to acquire considering the operations to which it will be subjected to in a certain service, also evaluates the motor train of the existing vehicles in the vehicular fleet of the transport companies. [Spanish] Las empresas de autotransporte en Mexico se ven afectadas en su economia principalmente por la baja eficiencia en el consumo de combustible, especialmente las destinadas al servicio pesado. No obstante la avanzada tecnologia de que se va disponiendo y adoptando en el parque vehicular con relacion a la eficiencia energetica, el costo por tonelada transportada no ha disminuido de manera importante. En este trabajo, se presenta un estudio sobre la influencia que tiene dentro de esta problematica, la seleccion de los componentes del tren motriz en el consumo de combustible y en la capacidad de ascenso del vehiculo en relacion con el peso de la carga transportada. Como resultado del estudio se desarrollo en el Instituto Mexicano del Transporte un programa de computo basado en

  17. Propulsion system research and development for electric and hybrid vehicles

    Science.gov (United States)

    Schwartz, H. J.

    1980-01-01

    An approach to propulsion subsystem technology is presented. Various tests of component reliability are described to aid in the production of better quality vehicles. component characterization work is described to provide engineering data to manufacturers on component performance and on important component propulsion system interactions.

  18. Vehicle seat design : state of the art and recent development

    NARCIS (Netherlands)

    Tan, C.F.; Delbressine, F.L.M.; Rauterberg, G.W.M.; Mokhtar, A.S.; Abdullah, E.J.; Adam, N.M.

    2007-01-01

    Seats are one of the most important components of vehicles and they are the place where professional driver spend most of their time. For example, according to Occupational Outlook Handbook by United State Department of Labor, the truck drivers frequently work 50 or more hours a week. The truck

  19. Development and Early Adoption of Electric Vehicles : Understanding the tempest

    NARCIS (Netherlands)

    Sierzchula, W.

    2015-01-01

    Electric vehicles are one innovation that could help reduce CO2 emissions from the transportation sector and mitigate the harmful effects of climate change. However, substantial roadblocks to their adoption exist including high purchase cost, lack of charging infrastructure, and long charging time.

  20. Appropriate payment vehicles in stated preference studies in developing economies

    DEFF Research Database (Denmark)

    Hassan, Suziana; Olsen, Søren Bøye; Thorsen, Bo Jellesmark

    2018-01-01

    , in Malaysia as well as in many other low- to middle-income economies, large proportions of people do not pay income taxes, putting the validity of this payment vehicle into question. Instead, citizens in Malaysia and many other countries benefit from subsidies for a range of consumer goods. We find that price...

  1. Development and application of resilient wheels in urban rail transit vehicle

    Directory of Open Access Journals (Sweden)

    Juan WEN

    Full Text Available Urban rail transit vehicles have been more and more attractive to people as a kind of fast, comfortable, energy-saving, environmental protection and safe transportation. But because of the vehicle noise and vibration, urban rail vehicles also face severe challenges. The research of resilient wheels has been continuously developed and improved. Based on the review of development background and structure sorts of resilient wheels, the advantages of resilient wheels are described, and the research status of noise and vibration reducing, infinite element strength analysis, vehicle dynamic analysis and the wheel-rail wear of resilient wheels are discussed. Taking the low-floor LRVs (light rail vehicles in domestic and overseas as example, the development and application of the resilient wheels in city rail transit is described, and the application prospects of the resilient wheels in LRVs in domestic and the future research direction of elastic wheel are discussed.

  2. Development and application of underwater robot vehicle for close inspection of spent fuels

    Energy Technology Data Exchange (ETDEWEB)

    Yun, J. S.; Park, B. S.; Song, T. G.; Kim, S. H.; Cho, M. W.; Ahn, S. H.; Lee, J. Y.; Oh, S. C.; Oh, W. J.; Shin, K. W.; Woo, D. H.; Kim, H. G.; Park, J. S

    1999-12-01

    The research and development efforts of the underwater robotic vehicle for inspection of spent fuels are focused on the development of an robotic vehicle which inspects spent fuels in the storage pool through remotely controlled actuation. For this purpose, a self balanced vehicle actuated by propellers is designed and fabricated, which consists of a radiation resistance camera, two illuminators, a pressure transducer and a manipulator. the algorithm for autonomous navigation is developed and its performance is tested at the swimming pool. The results of the underwater vehicle shows that the vehicle can easily navigate into the arbitrary directions while maintaining its balanced position. The camera provides a clear view of working environment by using the macro and zoom functions. The camera tilt device provides a wide field of view which is enough for monitoring the operation of manipulator. Also, the manipulator can pick up the dropped objects up to 4 kgf of weight. (author)

  3. Development of A Hydraulic Drive for a novel Diesel-Hydraulic system for Large commercial Vehicles

    DEFF Research Database (Denmark)

    Stecki, J. S.; Conrad, Finn; Matheson, P.

    2002-01-01

    The objectives and results of the research project Hybrid Diesel-Hydraulic System for Large commercial vehicles, e.g. urban freight delivery, buses or garbage trucks. The paper presents and discusses the research and development of the system, modelling approach and results from preliminary...... performance tests on a 10 ton vehicle....

  4. Delay-based Passenger Car Equivalent at Signalized Intersections in Iran

    Directory of Open Access Journals (Sweden)

    Habibollah Nassiri

    2017-04-01

    Full Text Available Due to their different sizes and operational characteristics, vehicles other than passenger cars have a different influence on traffic operations especially at intersections. The passenger car equivalent (PCE is the parameter that shows how many passenger cars must be substituted for a specific heavy vehicle to represent its influence on traffic operation. PCE is commonly estimated using headway-based methods that consider the excess headway utilized by heavy vehicles. In this research, the PCE was estimated based on the delay parameter at three signalized intersections in Tehran, Iran. The data collected were traffic volume, travel time for each movement, signalization, and geometric design information. These data were analysed and three different models, one for each intersection, were constructed and calibrated using TRAF-NETSIM simulation software for unsaturated traffic conditions. PCE was estimated under different scenarios and the number of approach movements at each intersection. The results showed that for approaches with only one movement, PCE varies from 1.1 to 1.65. Similarly, for approaches with two and three movements, the PCE varies from 1.07 to 1.99 and from 0.76 to 3.6, respectively. In addition, a general model was developed for predicting PCE for intersections with all of the movements considered. The results obtained from this model showed that the average PCE of 1.5 is similar to the value recommended by the HCM (Highway Capacity Manual 1985. However, the predicted PCE value of 1.9 for saturated threshold is closer to the PCE value of 2 which was recommended by the HCM 2000 and HCM 2010.

  5. Small passenger car transmission test-Chevrolet 200 transmission

    Science.gov (United States)

    Bujold, M. P.

    1980-01-01

    The small passenger car transmission was tested to supply electric vehicle manufacturers with technical information regarding the performance of commerically available transmissions which would enable them to design a more energy efficient vehicle. With this information the manufacturers could estimate vehicle driving range as well as speed and torque requirements for specific road load performance characteristics. A 1979 Chevrolet Model 200 automatic transmission was tested per a passenger car automatic transmission test code (SAE J651b) which required drive performance, coast performance, and no load test conditions. The transmission attained maximum efficiencies in the mid-eighty percent range for both drive performance tests and coast performance tests. Torque, speed and efficiency curves map the complete performance characteristics for Chevrolet Model 200 transmission.

  6. Development of a driving cycle to evaluate the energy economy of electric vehicles in urban areas

    International Nuclear Information System (INIS)

    Brady, John; O’Mahony, Margaret

    2016-01-01

    Highlights: • Development of a driving cycle to evaluate energy economy of electric vehicles. • Improves on existing driving cycles by using real world data from electric vehicles. • Driving data from different road types and traffic conditions included. - Abstract: Understanding real-world driving conditions in the form of driving cycles is instrumental in the design of efficient powertrains and energy storage systems for electric vehicles. In addition, driving cycles serve as a standardised measurement procedure for the certification of a vehicle’s fuel economy and driving range. They also facilitate the evaluation of the economic and lifecycle costs of emerging vehicular technologies. However, discrepancies between existing driving cycles and real-world driving conditions exist due to a number of factors such as insufficient data, inadequate driving cycle development methodologies and methods to assess the representativeness of developed driving cycles. The novel aspect of the work presented here is the use of real-world data from electric vehicles, over a six month period, to derive a driving cycle appropriate for their assessment. A stochastic and statistical methodology is used to develop and assess the representativeness of the driving cycle against a separate set of real world electric vehicle driving data and the developed cycle performs well in that comparison. Although direct comparisons with internal combustion engine driving cycles are not that informative or relevant due to the marked differences between how they and electric vehicles operate, some discussion around how the developed electric vehicle cycle relates to them is also included.

  7. Tendencies in the selection of materials for passenger cars from the viewpoint of the development of sport cars

    Energy Technology Data Exchange (ETDEWEB)

    Bott, H

    1981-05-18

    Aluminium as a substitute material for steel is discussed. A short discussion of glass fiber reinforced plastics and polyurethane is given. Car weights, components, and relevant construction materials are discussed. The outlook for tendencies and developments is described.

  8. Numerical method for assessing the potential of smart engine thermal management: Application to a medium-upper segment passenger car

    International Nuclear Information System (INIS)

    Caresana, F.; Bilancia, M.; Bartolini, C.M.

    2011-01-01

    Significant reductions in vehicle fuel consumption can be obtained through a greater control of the thermal status of the engine, especially under partial load conditions. Different systems have been proposed to implement this concept, referred to as improved engine thermal management. The amount of fuel saved depends on the components and layout of the engine cooling plant and on the performance of its control system. In this work, a method was developed to calculate the theoretical minimum fuel consumption of a passenger car and used as a reference in comparing different engine cooling system concepts. A high-medium class car was taken as an example and simulated on standard cycles. Models for power train and cooling system components were developed and linked to simulate the vehicle. A preliminary analysis of the engine was performed using AVL's Boost program. The fuel consumption of the complete vehicle, equipped with a conventional cooling plant, was determined on standard cycles and compared with that of a vehicle equipped with a 'perfect' cooling system, to calculate the theoretical reduction in fuel consumption. - Highlights: → We propose a method for assessing the potential of smart engine thermal management. → A conventional cooling system is compared to a 'perfect' one to estimate fuel economy. → We tested the method in an upper-medium segment passenger car.

  9. Electric Vehicle Scenarios for India: Implications for mitigation and development

    DEFF Research Database (Denmark)

    Shukla, P.R.; Dhar, Subash; Bhaskar, Kalyan

    2014-01-01

    to infrastructure and policies. While the literature on EVs has focused more on the role of electric cars, it could be electric two-wheelers which could make early headway, as is the case in China where nearly 120 million such vehicles had been sold by the end of 2012. Three scenarios (Business as Usual (BAU......The transport sector globally is overly dependent on liquid fossil fuels. Electric vehicles (EVs) are touted as a way of diversifying the fuel mix and helping to reduce dependence on fossil fuels. There could also be other co-benefits of EVs, such as improved energy security, decarbonising...... of the electricity sector, CO2 mitigation and reduction in local air pollution. The Indian government has recently launched a national electricity mobility mission to promote EVs. There is, however, much uncertainty in terms of the penetration of EVs in the transport sector, particularly those related...

  10. Driving cycles for measuring passenger car emissions on roads with traffic calming measures

    International Nuclear Information System (INIS)

    Boulter, P.G.; Latham, S.; Ainge, M.

    1999-01-01

    Although local authorities in the UK need to be aware of any air quality impacts resulting from their traffic calming operations, there is little information relating to the effects of different traffic calming measures. The effects on air quality on this scale are complex, and so TRL is providing guidance by developing performance indices for different measures based on their effects on vehicle emissions. The emissions indices for passenger cars are based on tests conducted on a chassis dynamometer, and this paper describes the development of the methodology for constructing the driving cycles to be used. The technique involves the measurement of the speed profiles of a large number of vehicles using a roadside LIDAR system, and the determination of typical gear selections using three-instrumented cars

  11. Air-Breathing Launch Vehicle Technology Being Developed

    Science.gov (United States)

    Trefny, Charles J.

    2003-01-01

    Of the technical factors that would contribute to lowering the cost of space access, reusability has high potential. The primary objective of the GTX program is to determine whether or not air-breathing propulsion can enable reusable single-stage-to-orbit (SSTO) operations. The approach is based on maturation of a reference vehicle design with focus on the integration and flight-weight construction of its air-breathing rocket-based combined-cycle (RBCC) propulsion system.

  12. Development of a Strategy for Simulating Blast-Vehicle Interactions

    Science.gov (United States)

    2010-09-01

    Magnus effect . Although large rotational speeds were measured, it was concluded that the Magnus force had little influence and did not significantly...CHEM (rigid flat-plate). 104 Figure 5.3: Geometry used for blast wave interacting with a cylinder (Ofengeim and Drikakis 1997). 105 Figure 5.4: CFD...their effects on vehicles and their human occupants. The framework couples the MPMICE CFD code with DYNA3D and LS-DYNA finite element codes

  13. Design and development of electric vehicle charging station equipped with RFID

    Science.gov (United States)

    Panatarani, C.; Murtaddo, D.; Maulana, D. W.; Irawan, S.; Joni, I. M.

    2016-02-01

    This paper reports the development of electric charging station from distributed renewable for electric vehicle (EV). This designed refer to the input voltage standard of IEC 61851, plugs features of IEC 62196 and standard communication of ISO 15118. The developed electric charging station used microcontroller ATMEGA8535 and RFID as controller and identifier of the EV users, respectively. The charging station successfully developed as desired features for electric vehicle from renewable energy resources grid with solar panel, wind power and batteries storage.

  14. Getting passengers out : evacuation behaviours

    NARCIS (Netherlands)

    Boer, L.C.

    2003-01-01

    When disaster strikes, mass transportation means mass evacuation. The issue is especially urgent if, despite precautions, a train comes to a stop in a tunnel and there is a fire. Adequate behaviour of passengers is a major success factor of an evacuation. Passengers should replace their original

  15. Energy Star Concepts for Highway Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Greene, D.L.

    2003-06-24

    The authors of this report, under the sponsorship of the U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE) Weatherization and Intergovernmental Program, have investigated the possible application of Energy Star ratings to passenger cars and light trucks. This study establishes a framework for formulating and evaluating Energy Star rating methods that is comprised of energy- and environmental-based metrics, potential vehicle classification systems, vehicle technology factors, and vehicle selection criteria. The study tests several concepts and Energy Star rating methods using model-year 2000 vehicle data--a spreadsheet model has been developed to facilitate these analyses. This study tests two primary types of rating systems: (1) an outcome-based system that rates vehicles based on fuel economy, GHG emissions, and oil use and (2) a technology-based system that rates vehicles based on the energy-saving technologies they use. Rating methods were evaluated based on their ability to select vehicles with high fuel economy, low GHG emissions, and low oil use while preserving a full range of service (size and acceleration) and body style choice. This study concludes that an Energy Star rating for passenger cars and light trucks is feasible and that several methods could be used to achieve reasonable tradeoffs between low energy use and emissions and diversity in size, performance, and body type. It also shows that methods that consider only fuel economy, GHG emissions, or oil use will not select a diverse mix of vehicles. Finally, analyses suggest that methods that encourage the use of technology only, may result in increases in acceleration power and weight rather than reductions in oil use and GHG emissions and improvements in fuel economy.

  16. Licensing of non intrusive inspection equipment s for load and passengers vehicles that use X rays with energies up to 9 MeV. Mexican experience; Licenciamiento de equipos de inspeccion no intrusiva para vehiculos de carga y pasajeros que utilizan rayos X con energias de hasta 9 megaelectronvolts. Experiencia Mexicana

    Energy Technology Data Exchange (ETDEWEB)

    Munoz M, G. A.; Jimenez C, I., E-mail: armando.munoz@cnsns.gob.mx [Comision Nacional de Seguridad Nuclear y Salvaguardias, Dr. Jose Ma. Barragan 779, Col. Narvarte, 03020 Mexico D. F. (Mexico)

    2013-10-15

    In the last years and like part of the extensive program of national security, in Mexico have been introduced a great quantity of non intrusive inspection equipment s for load and passengers vehicles that use X rays up to 9 MeV. Due to the great variety of equipment s, the Comision Nacional de Seguridad Nuclear y Salvaguardias (Mexican regulator organ) has established specific guidelines for their licensing and use supervision. In this work the adopted guidelines are exposed in the technical and administrative evaluation for the later licensing of these equipment s. Relative particular questions to the site of these equipment s and the impact in the public opinion that their use can generate are discussed. (author)

  17. Hybrid vehicle potential assessment. Volume 7: Hybrid vehicle review

    Science.gov (United States)

    Leschly, K. O.

    1979-01-01

    Review of hybrid vehicles built during the past ten years or planned to be built in the near future is presented. An attempt is made to classify and analyze these vehicles to get an overall picture of their key characteristics. The review includes onroad hybrid passenger cars, trucks, vans, and buses.

  18. Development of engine sound quality for passenger car with 6 cylinder engine; 6 kito engine joyosha no onshoku kazari

    Energy Technology Data Exchange (ETDEWEB)

    Iwasaki, Y; Miyamoto, K; Yamamoto, K [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    In recent years, the interior noise has been required not only to reduce the sound pressure level, but also to improve the sound quality, especially during acceleration. This paper describes the development of engine sound quality for the new model `ARISTO (GS300)` with in-line 6 gasoline engine. We used the sound simulator in order to evaluate the engine sound quality during acceleration, and decided the target sound. To attain that sound, the light-weighed Piston and connecting rod, and the improvement of intake system are adopted. 7 refs., 13 figs.

  19. Increasing the availability of urban passenger transport on objective ...

    African Journals Online (AJOL)

    Increasing the availability of urban passenger transport on objective control data ... mathematical modeling, probability theory and mathematical statistics, expert ... intended for development of methods and means of operative management of ...

  20. Occupant Volume Integrity Evaluation in Passenger Rail Cars

    Science.gov (United States)

    2012-02-01

    This research, which is intended to enable the growth of high-speed and intercity passenger rail transportation, was sponsored by the Federal Railroad Administration (FRA) Office of Research and Development, as part of the train Occupant Protection r...

  1. Safer passenger car front shapes for pedestrians: A computational approach to reduce overall pedestrian injury risk in realistic impact scenarios.

    Science.gov (United States)

    Li, Guibing; Yang, Jikuang; Simms, Ciaran

    2017-03-01

    Vehicle front shape has a significant influence on pedestrian injuries and the optimal design for overall pedestrian protection remains an elusive goal, especially considering the variability of vehicle-to-pedestrian accident scenarios. Therefore this study aims to develop and evaluate an efficient framework for vehicle front shape optimization for pedestrian protection accounting for the broad range of real world impact scenarios and their distributions in recent accident data. Firstly, a framework for vehicle front shape optimization for pedestrian protection was developed based on coupling of multi-body simulations and a genetic algorithm. This framework was then applied for optimizing passenger car front shape for pedestrian protection, and its predictions were evaluated using accident data and kinematic analyses. The results indicate that the optimization shows a good convergence and predictions of the optimization framework are corroborated when compared to the available accident data, and the optimization framework can distinguish 'good' and 'poor' vehicle front shapes for pedestrian safety. Thus, it is feasible and reliable to use the optimization framework for vehicle front shape optimization for reducing overall pedestrian injury risk. The results also show the importance of considering the broad range of impact scenarios in vehicle front shape optimization. A safe passenger car for overall pedestrian protection should have a wide and flat bumper (covering pedestrians' legs from the lower leg up to the shaft of the upper leg with generally even contacts), a bonnet leading edge height around 750mm, a short bonnet (17° or car front shape for head and leg protection are generally consistent, but partially conflict with pelvis protection. In particular, both head and leg injury risk increase with increasing bumper lower height and depth, and decrease with increasing bonnet leading edge height, while pelvis injury risk increases with increasing bonnet leading

  2. Development of Micro Air Vehicle Technology With In-Flight Adaptive-Wing Structure

    Science.gov (United States)

    Waszak, Martin R. (Technical Monitor); Shkarayev, Sergey; Null, William; Wagner, Matthew

    2004-01-01

    This is a final report on the research studies, "Development of Micro Air Vehicle Technology with In-Flight Adaptrive-Wing Structure". This project involved the development of variable-camber technology to achieve efficient design of micro air vehicles. Specifically, it focused on the following topics: 1) Low Reynolds number wind tunnel testing of cambered-plate wings. 2) Theoretical performance analysis of micro air vehicles. 3) Design of a variable-camber MAV actuated by micro servos. 4) Test flights of a variable-camber MAV.

  3. The role of nanotechnology in the development of battery materials for electric vehicles.

    Science.gov (United States)

    Lu, Jun; Chen, Zonghai; Ma, Zifeng; Pan, Feng; Curtiss, Larry A; Amine, Khalil

    2016-12-06

    A significant amount of battery research and development is underway, both in academia and industry, to meet the demand for electric vehicle applications. When it comes to designing and fabricating electrode materials, nanotechnology-based approaches have demonstrated numerous benefits for improved energy and power density, cyclability and safety. In this Review, we offer an overview of nanostructured materials that are either already commercialized or close to commercialization for hybrid electric vehicle applications, as well as those under development with the potential to meet the requirements for long-range electric vehicles.

  4. Hypersonic vehicle control law development using H(infinity) and micron-synthesis

    Science.gov (United States)

    Gregory, Irene M.; Mcminn, John D.; Shaughnessy, John D.; Chowdhry, Rajiv S.

    1993-01-01

    Hypersonic vehicle control law development using H(infinity) and mu-synthesis is discussed. Airbreathing SSTO vehicles has a mutli-faceted mission that includes orbital operations, as well as re-entry and descent culminating in horizontal landing. However, the most challenging part of the operations is the ascent to orbit. The airbreathing propulsion requires lengthy atmospheric flight that may last as long as 30 minutes and take the vehicle half way around the globe. The vehicles's ascent is characterized by tight payload to orbit margins which translate into minimum fuel orbit as the performance criteria. Issues discussed include: SSTO airbreathing vehicle issues; control system performance requirements; robust control law framework; H(infinity) controller frequency analysis; and mu controller frequency analysis.

  5. Development and Demonstration of a Magnesium-Intensive Vehicle Front-End Substructure

    Energy Technology Data Exchange (ETDEWEB)

    Logan, Stephen D. [United States Automotive Materials Partnership LLC, Southfield, MI (United States); Forsmark, Joy H. [United States Automotive Materials Partnership LLC, Southfield, MI (United States); Osborne, Richard [United States Automotive Materials Partnership LLC, Southfield, MI (United States)

    2016-07-01

    This project is the final phase (designated Phase III) of an extensive, nine-year effort with the objectives of developing a knowledge base and enabling technologies for the design, fabrication and performance evaluation of magnesium-intensive automotive front-end substructures intended to partially or completely replace all-steel comparators, providing a weight savings approaching 50% of the baseline. Benefits of extensive vehicle weight reduction in terms of fuel economy increase, extended vehicle range, vehicle performance and commensurate reductions in greenhouse gas emissions are well known. An exemplary vehicle substructure considered by the project is illustrated in Figure 1, along with the exterior vehicle appearance. This unibody front-end “substructure” is one physical objective of the ultimate design and engineering aspects established at the outset of the larger collective effort.

  6. Development and Testing of a Prototype Connected Vehicle Wrong-Way Driving Detection and Management System

    Science.gov (United States)

    2018-02-01

    The primary objective of Phase II was to develop a prototype connected vehicle wrong-way driving detection and management system at the Texas A&M University Respect, Excellence, Leadership, Loyalty, Integrity, Selfless Service (RELLIS) campus. The pu...

  7. Development and Optimization of a Tridyne Pressurization System for Pressure Fed Launch Vehicles

    National Research Council Canada - National Science Library

    Chakroborty, Shyama; Wollen, Mark; Malany, Lee

    2006-01-01

    Over the recent years, Microcosm has been pursuing the development of a Tridyne-based pressurization system and its implementation in the Scorpius family of launch vehicles to obtain substantial gain in payload to orbit...

  8. Development of wireless vehicle remote control for fuel lid operation

    Science.gov (United States)

    Sulaiman, N.; Jadin, M. S.; Najib, M. S.; Mustafa, M.; Azmi, S. N. F.

    2018-04-01

    Nowadays, the evolution of the vehicle technology had made the vehicle especially car to be equipped with a remote control to control the operation of the locking and unlocking system of the car’s door and rear’s bonnet. However, for the fuel or petrol lid, it merely can be opened from inside the car’s cabin by handling the fuel level inside the car’s cabin to open the fuel lid. The petrol lid can be closed by pushing the lid by hand. Due to the high usage of using fuel lever to open the fuel lid when refilling the fuel, the car driver might encounter the malfunction of fuel lid (fail to open) when pushing or pulling the fuel lever. Thus, the main aim of the research is to enhance the operation of an existing car remote control where the car fuel lid can be controlled using two techniques; remote control-based and smartphone-based. The remote control is constructed using Arduino microcontroller, wireless sensors and XCTU software to set the transmitting and receiving parameters. Meanwhile, the smartphone can control the operation of the fuel lid by communicating with Arduino microcontroller which is attached to the fuel lid using Bluetooth sensor to open the petrol lid. In order to avoid the conflict of instruction between wireless systems with the existing mechanical-based system, the servo motor will be employed to release the fuel lid merely after receiving the instruction from Arduino microcontroller and smartphone. As a conclusion, the prototype of the multipurpose vehicle remote control is successfully invented, constructed and tested. The car fuel lid can be opened either using remote control or smartphone in a sequential manner. Therefore, the outcome of the project can be used to serve as an alternative solution to solve the car fuel lid problem even though the problem rarely occurred.

  9. The Hybrid Airline Model. Generating Quality for Passengers

    Directory of Open Access Journals (Sweden)

    Bogdan AVRAM

    2017-12-01

    Full Text Available This research aims to investigate the different strategies adopted by the airline companies in adapting to the ongoing changes while developing products and services for passengers in order to increase their yield, load factor and passenger satisfaction. Finding a balance between costs and services quality in the airline industry is a crucial task for every airline wanting to gain a competitive advantage on the market. Also, the rise of the hybrid business operating model has brought up many challenges for airlines as the line between legacy carriers and low-cost carriers is getting thinner in terms of costs and innovative ideas to create a superior product for the passengers.

  10. Emissions of nitrogen oxides and particulates of diesel vehicles

    OpenAIRE

    Kadijk, G.; Ligterink, N.E.; Mensch, P. van; Spreen, J.S.; Vermeulen, R.J.; Vonk, W.A.

    2015-01-01

    In real-world conditions, modern Euro VI heavy-duty vehicles produce an average of ten times less nitrogen oxide (NOx)emissions than previous generations of Euro IV and Euro V heavy-duty vehicles. However, Euro 6 passenger cars and light commercial vehicles present an entirely different picture since, despite a continual tightening of European emissions limits, the real-world NOx emissions of new diesel passenger cars and light commercial vehicles have remained virtually unchanged over the la...

  11. The measurement of dynamic radii for passenger car tyre

    Science.gov (United States)

    Anghelache, G.; Moisescu, R.

    2017-10-01

    The tyre dynamic rolling radius is an extremely important parameter for vehicle dynamics, for operation of safety systems as ESP, ABS, TCS, etc., for road vehicle research and development, as well as for validation or as an input parameter of automotive simulations and models. The paper investigates the dynamic rolling radii of passenger car tyre and the influence of rolling speed and inflation pressure on their magnitude. The measurement of dynamic rolling radii has been performed on a chassis dynamometer test rig. The dynamic rolling radii have been measured indirectly, using longitudinal rolling speed and angular velocity of wheel. Due to the subtle effects that the parameters have on rolling radius magnitude, very accurate equipment has to be used. Two different methods have been chosen for measuring the wheel angular velocity: the stroboscopic lamp and the incremental rotary encoder. The paper shows that the stroboscopic lamp has an insufficient resolution, therefore it was no longer used for experimental investigation. The tyre dynamic rolling radii increase with rolling speed and with tyre inflation pressure, but the effect of pressure is more significant. The paper also makes considerations on the viability of simplified formulae from literature for calculating the tyre dynamic rolling radius.

  12. Investigation of Gas Piston Actuated Opening-Closing Trunk Lid Mechanisms Used in Passenger Cars

    Directory of Open Access Journals (Sweden)

    Ahmet YILDIZ

    2015-05-01

    Full Text Available In this study, the gas piston actuated opening-closing trunk lid mechanisms used in passenger cars are investigated theoretically and experimentally. First, the position analysis of the mechanism which is a four-bar linkage has been carried out. Then the quasi-static analyzes according to the principle of virtual work have been made, and so the hand force, one of the most important parameters in terms of ergonomics, required for opening and closing the trunk lid has been calculated. In order to verify this developed model, the hand force has been determined also experimentally, performing the physical tests on an existing vehicle at Turkish Automobile Factory Inc. (TOFAŞ. Eventually, it is observed that the results obtained from mathematical model and the experimental measurements are compatible each other. This established model will provide convenience for manufacturers to determine the hand force for different model of vehicles

  13. Simulation to assess the efficacy of US airport entry scrreening of passengers for pandemic influenza

    Energy Technology Data Exchange (ETDEWEB)

    Mcmahon, Benjamin [Los Alamos National Laboratory

    2009-01-01

    We present our methodology and stochastic discrete-event simulation developed to model the screening of passengers for pandemic influenza at the US port-of-entry airports. Our model uniquely combines epidemiology modelling, evolving infected states and conditions of passengers over time, and operational considerations of screening in a single simulation. The simulation begins with international aircraft arrivals to the US. Passengers are then randomly assigned to one of three states -- not infected, infected with pandemic influenza and infected with other respiratory illness. Passengers then pass through various screening layers (i.e. pre-departure screening, en route screening, primary screening and secondary screening) and ultimately exit the system. We track the status of each passenger over time, with a special emphasis on false negatives (i.e. passengers infected with pandemic influenza, but are not identified as such) as these passengers pose a significant threat as they could unknowingly spread the pandemic influenza virus throughout our nation.

  14. Near-term electric test vehicle ETV-2. Phase II. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1981-04-01

    A unique battery-powered passenger vehicle has been developed that provides a significant improvement over conventional electric vehicle performance, particularly during stop-and-go driving. The vehicle is unique in two major respects: (1) the power system incorporates a flywheel that stores energy during regenerative braking and makes possible the acceleration capability needed to keep up with traffic without reducing range to unacceptable values; and (2) lightweight plastic materials are used for the vehicle unibody to minimize weight and increase range. These features were analyzed and demonstrated in an electric test vehicle, ETV-2. Characteristics of this vehicle are summarized. Information is presented on: vehicle design, fabrication, safety testing, and performance testing; power system design and operation; flywheel; battery pack performance; and controls and electronic equipment. (LCL)

  15. Development of Degree-of-Priority Based Control Strategy for Emergency Vehicle Preemption Operation

    Directory of Open Access Journals (Sweden)

    Jiawen Wang

    2013-01-01

    Full Text Available This paper proposes a degree-of-priority based control strategy for emergency vehicle preemption operation to decrease the impacts of emergency vehicles on normal traffic. The proposed model features its effectiveness to the following three aspects: (1 a multilayer fuzzy model was established to determine the degree-of-priority based on emergency vehicle preemption demand intensity and preemption influence intensity; (2 for emergency vehicles with proper classification, a travel time estimation model for emergency traffic was formulated, an optimal emergency route determines model based on the level of priority of emergency events, and the emergency vehicle travel time was developed to minimize evacuation time as well as minimize the adverse impacts of preemption on normal traffic; and (3 a conditional traffic signals priority control method at each intersection of the evacuation route was built, so that traffic queue at each intersection can be cleared before the arrival of emergency vehicles. A simulation model based on field data was developed, and the performance of the proposed strategy was compared with the conventional local detection based method under the microscopic simulation model. The results validated the efficiency of the proposed strategy in terms of minimizing the delay of emergency vehicles and reducing adverse impacts on normal traffic.

  16. German electric vehicle charging infrastructure: statistically based approach to derive the demand and geographical distribution of charging points

    OpenAIRE

    González Villafranca, Sara

    2013-01-01

    Electromobility is widely seen as one of the most promising options to reduce Greenhouse gas emissions in passenger transport. In accordance with the German Government via the National Platform for Electromobility (NPE), an estimated target of 1 million of electric vehicles for 2020 is expected for Germany. One challenge for the widespread development of electric vehicles market is the lack of infrastructure. The great unknowns here are: how many charging stations will be needed in the future...

  17. Quieter Cars and the Safety of Blind Pedestrians, Phase 2 : Development of Potential Specifications for Vehicle Countermeasure Sounds.

    Science.gov (United States)

    2011-10-01

    This project performed research to support the development of potential specifications for vehicle : sounds, (i.e., audible countermeasures) to be used in vehicles while operating in electric mode in specific low speed : conditions. The purpose of th...

  18. FY2011 Annual Progress Report for Advanced Combustion Engine Research and Development

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2011-12-01

    Annual Progress Report for the Advanced Combustion Engine Research and Development (R&D) subprogram supporting the mission of the Vehicle Technologies Program by removing the critical technical barriers to commercialization of advanced internal combustion engines (ICEs) for passenger and commercial vehicles that meet future federal emissions regulations.

  19. The ParaShield Entry Vehicle Concept: Basic Theory and Flight Test Development

    OpenAIRE

    Akin, David

    1990-01-01

    With the emergence of microsatellite launch vehicle technology and the development of interest in space commercialization, there is a renewed need for entry vehicle technology to return mass from low earth orbit. This paper documents the ParaShield concept of the Space Systems Laboratory, which is an ultra-low ballistic coefficient (ULβ) entry vehicle. Trajectory simulations show that as the ballistic coefficient is lowered into the range of 100-150 Pa (2-3lb/ft2) the total heat load and peak...

  20. 14 CFR 91.517 - Passenger information.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Passenger information. 91.517 Section 91... Multiengine Airplanes and Fractional Ownership Program Aircraft § 91.517 Passenger information. (a) Except as... belts and when smoking is prohibited. (c) If passenger information signs are installed, no passenger or...

  1. Consumption and efficiency of a passenger car with a hydrogen/oxygen PEFC based hybrid electric drivetrain

    Energy Technology Data Exchange (ETDEWEB)

    Buechi, F.N.; Dietrich, P.; Tsukada, A.; Koetz, R.; Freunberger, S.A. [Paul Scherrer Institut, Electrochemistry Laboratory, CH-5232 Villigen PSI (Switzerland); Paganelli, G.; Laurent, D.; Varenne, P.; Delfino, A.; Magne, P.A.; Walser, D.; Olsommer, D. [Conception et Developpement Michelin, Route Andre-Piller 30, CH-1762 Givisiez (Switzerland)

    2007-08-15

    The main factors for reducing the consumption of a vehicle are reduction of curb weight, air drag and increase in the drivetrain efficiency. Highly efficient drivetrains can be developed based on PEFC technology and curb weight may be limited by an innovative vehicle construction. In this paper, data on consumption and efficiency of a four-place passenger vehicle with a curb weight of 850 kg and an H{sub 2}/O{sub 2} fed PEFC/Supercap hybrid electric powertrain are presented. Hydrogen consumption in the New European Driving Cycle is 0.67 kg H{sub 2}/100 km, which corresponds to a gasoline equivalent consumption of 2.5 l/100 km. When including the energy needed to supply pure oxygen, the calculated consumption increases from 0.67 to 0.69-0.79 kg H{sub 2}/100 km, depending on the method of oxygen production. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

  2. A unit for environmentally adapted technology for transportation of passengers and goods. Individual personal transportation, electric and hybrid vehicles - a preliminary study; Enhet foer miljoeanpassad teknik foer person- och godstransporter - Individuell persontrafik, el- och hybridfordon - Foerstudie

    Energy Technology Data Exchange (ETDEWEB)

    Bauner, D; Lumsden, K [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Transportation and Logistics

    1996-02-01

    A unit for environmentally adapted transport at Chalmers Univ of Technology offers the possibility to enhance competence, to bestow decision makers with information and permits working with the processes needed. Regarding electric propulsion road vehicles, such a unit can coordinate the experiences from the Swedish projects. Further, it may maintain a secretariat and a managerial function to the database which will provide information to research councils, transport administrations and other government organizations, cities etc. The unit may also coordinate and submit research results and, in a long-term perspective, establish and administer field and laboratory vehicle testing. The unit may also function as a link between the vehicle industry and environmental organizations. The initial activities should include the establishment of a national database for electric vehicles and a full-time research post. The present study deals with individual personal transportation. Corresponding studies should be carried out for other areas in order to form a consistent profile for the unit. 38 refs

  3. Location Planning for Dynamic Wireless Charging Systems for Electric Airport Passenger Buses

    Directory of Open Access Journals (Sweden)

    Stefan Helber

    2018-01-01

    Full Text Available The majority of the ground vehicles operating on the airside parts of commercial airports are currently powered by diesel engines. These include vehicles such as apron buses, fuel trucks, and aircraft tractors. Hence, these vehicles contribute to the overall CO 2 emissions of the aviation transport system and thus negatively influence its environmental footprint. To reduce this damaging environmental impact, these vehicles could potentially be electrified with on-board batteries as their energy sources. However, the conductive charging of such vehicles via stationary cable connections is rather time-consuming. A dynamic wireless charging system to supply public transportation passenger buses with electric energy while in motion has recently been installed on the Korea Advanced Institute of Science and Technology (KAIST campus and in the Korean city of Gumi. In this paper, we study configuration problems related to the use of this technology to make airport operations more environmentally sustainable. We concentrate on the power supply for apron buses and analyze the location planning problems related to the distribution of the required power supply and the wireless charging units in the apron road system. To this end, we develop a formal optimization model and discuss the first numerical results.

  4. Increasing fuel efficiency of passenger cars with the “climate-control” system as a method of improving the ecological safety of the urban infrastructure

    Science.gov (United States)

    Burakova, L. N.; Burakova, A. D.; Burakova, O. D.; Dovbysh, V. O.

    2018-01-01

    Motor vehicle should provide safety and a high ecological standard of living for the population. One of the methods to improve the ecological friendliness of motor vehicles in particular passenger cars (cars), which are considered in this article, is the growth of their fuel economy. It is established that fuel consumption and the amount of specific emissions of harmful substances with exhaust gases of cars when using the “climate control” system depend on the effective ambient temperature, the color of the opaque car body elements, the power of the car engine and the interior volume. However, the simplest controlled factor is the color of the opaque car body elements, which is characterized by the coefficient of light reflection. In the course of experimental studies, we established the dependences of a change in fuel consumption and a share of reducing emissions of harmful substances with exhaust gases of passenger cars with the “climate control” system on the coefficient of light reflection. A method has been developed to reduce fuel consumption and the amount of specific emissions of harmful substances with the exhaust gases of passenger cars when using the “climate control” system, which involves painting the vehicle roof white and allows reducing fuel consumption by 5.5-10.3% and the amount of specific emissions of harmful substances by 0.37-1.13% (CO) and 0.47-1.08% (CH).

  5. Research, development, and demonstration of nickel-iron batteries for electric vehicle propulsion. Annual report, 1978

    Energy Technology Data Exchange (ETDEWEB)

    1979-10-01

    The objective of this program is to develop a nickel-iron battery suitable for use in electric vehicles. Ultimately, it is expected that a number of these batteries will be demonstrated under the Electric and Hybrid Vehicle Act of 1976. The report presents the technical approach and a summary of the progress that was achieved under the contract. Work began 1 May 1978. The report covers the period through September 1978. (TFD)

  6. Development of a ROV titanium manipulator for light work class ROV vehicles

    OpenAIRE

    Garay, Gaizka X.; Sosa, Dario

    2016-01-01

    This paper shows the development of a high technical equipment to be used as tooling of submersible ROV (Remote Operated Vehicles) for offshore operations, particularly the design and fabrication by Additive Manufacturing (AM) of a Titanium Manipulator for ROVs. From the initial concept and design until a new formed company “TITANROB”, this document shortly describes the fabrication of hydraulic titanium manipulators for mid size ROV vehicles, the TitanRob series M501, G500 ...

  7. Development of Anti-lock Braking System (ABS) for Vehicles Braking

    OpenAIRE

    Minh Vu Trieu; Oamen Godwin; Vassiljeva Kristina; Teder Leo

    2016-01-01

    This paper develops a real laboratory of anti-lock braking system (ABS) for vehicle and conducts real experiments to verify the ability of this ABS to prevent the vehicle wheel from being locked while braking. Two controllers of PID and fuzzy logic are tested for analysis and comparison. This ABS laboratory is designed for bachelor and master students to simulate and analyze performances of ABS with different control techniques on various roads and load conditions. Thi...

  8. Mobility chains analysis of technologies for passenger cars and light duty vehicles fueled with biofuels : application of the Greet model to project the role of biomass in America's energy future (RBAEF) project.

    Energy Technology Data Exchange (ETDEWEB)

    Wu, M.; Wu, Y.; Wang, M; Energy Systems

    2008-01-31

    The Role of Biomass in America's Energy Future (RBAEF) is a multi-institution, multiple-sponsor research project. The primary focus of the project is to analyze and assess the potential of transportation fuels derived from cellulosic biomass in the years 2015 to 2030. For this project, researchers at Dartmouth College and Princeton University designed and simulated an advanced fermentation process to produce fuel ethanol/protein, a thermochemical process to produce Fischer-Tropsch diesel (FTD) and dimethyl ether (DME), and a combined heat and power plant to co-produce steam and electricity using the ASPEN Plus{trademark} model. With support from the U.S. Department of Energy (DOE), Argonne National Laboratory (ANL) conducted, for the RBAEF project, a mobility chains or well-to-wheels (WTW) analysis using the Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model developed at ANL. The mobility chains analysis was intended to estimate the energy consumption and emissions associated with the use of different production biofuels in light-duty vehicle technologies.

  9. Vehicle to Grid Communication Standards Development, Testing and Validation - Status Report

    Energy Technology Data Exchange (ETDEWEB)

    Gowri, Krishnan; Pratt, Richard M.; Tuffner, Francis K.; Kintner-Meyer, Michael CW

    2011-09-01

    In the US, more than 10,000 electric vehicles (EV) have been delivered to consumers during the first three quarters of 2011. A large majority of these vehicles are battery electric, often requiring 220 volt charging. Though the vehicle manufacturers and charging station manufacturers have provided consumers options for charging preferences, there are no existing communications between consumers and the utilities to manage the charging demand. There is also wide variation between manufacturers in their approach to support vehicle charging. There are in-vehicle networks, charging station networks, utility networks each using either cellular, Wi-Fi, ZigBee or other proprietary communication technology with no standards currently available for interoperability. The current situation of ad-hoc solutions is a major barrier to the wide adoption of electric vehicles. SAE, the International Standards Organization/International Electrotechnical Commission (ISO/IEC), ANSI, National Institute of Standards and Technology (NIST) and several industrial organizations are working towards the development of interoperability standards. PNNL has participated in the development and testing of these standards in an effort to accelerate the adoption and development of communication modules.

  10. Definition and verification of a set of reusable reference architectures for hybrid vehicle development

    OpenAIRE

    Harrington, Cian

    2012-01-01

    Current concerns regarding climate change and energy security have resulted in an increasing demand for low carbon vehicles, including: more efficient internal combustion engine vehicles, alternative fuel vehicles, electric vehicles and hybrid vehicles. Unlike traditional internal combustion engine vehicles and electric vehicles, hybrid vehicles contain a m...

  11. Assessment of the vibration on the foam legged and sheet metal-legged passenger seat

    Directory of Open Access Journals (Sweden)

    L. Dahil

    2015-10-01

    Full Text Available In this study, it was aim ed to decrease the vibration reaching to passenger from the legs of vehicle seats. In order to determine the levels of vibrations reaching at passengers, a test pad placed under the passenger seat was used, and HVM100 device was used for digitizing the information obtained. By transferring the vibration data to system by using HVM100 device, the acceleration graphics were prepared with Blaze software. As a result, it was determined that the acceleration values of seat legs made of foam material were lower than that of seat legs made of 2 mm thick sheet metal, so they damped the vibration better.

  12. A comparison of safety belt use between commercial and noncommercial light-vehicle occupants.

    Science.gov (United States)

    Eby, David W; Fordyce, Tiffani A; Vivoda, Jonathon M

    2002-05-01

    The purpose of this study was to conduct an observational survey of safety belt use to determine the use rate of commercial versus noncommercial light-vehicle occupants. Observations were conducted on front-outboard vehicle occupants in eligible commercial and noncommercial vehicles in Michigan (i.e.. passenger cars, vans/minivans, sport-utility vehicles, and pickup trucks). Commercial vehicles that did not fit into one of the four vehicle type categories, such as tractor-trailers, buses, or heavy trucks, were not included in the survey. The study found that the restraint use rate for commercial light-vehicle occupants was 55.8% statewide. The statewide safety belt use rate for commercial light-vehicles was significantly lower than the rate of 71.2% for noncommercial light-vehicles. The safety belt use rate for commercial vehicles was also significantly different as a function of region, vehicle type, seating position, age group, and road type. The results provide important preliminary data about safety belt use in commercial versus noncommercial light-vehicles and indicate that further effort is needed to promote safety belt use in the commercial light-vehicle occupant population. The study also suggests that additional research is required in order to develop effective programs that address low safety belt use in the commercial light-vehicle occupant population.

  13. Developing operator capacity estimates for supervisory control of autonomous vehicles.

    Science.gov (United States)

    Cummings, M L; Guerlain, Stephanie

    2007-02-01

    This study examined operators' capacity to successfully reallocate highly autonomous in-flight missiles to time-sensitive targets while performing secondary tasks of varying complexity. Regardless of the level of autonomy for unmanned systems, humans will be necessarily involved in the mission planning, higher level operation, and contingency interventions, otherwise known as human supervisory control. As a result, more research is needed that addresses the impact of dynamic decision support systems that support rapid planning and replanning in time-pressured scenarios, particularly on operator workload. A dual screen simulation that allows a single operator the ability to monitor and control 8, 12, or 16 missiles through high level replanning was tested on 42 U.S. Navy personnel. The most significant finding was that when attempting to control 16 missiles, participants' performance on three separate objective performance metrics and their situation awareness were significantly degraded. These results mirror studies of air traffic control that demonstrate a similar decline in performance for controllers managing 17 aircraft as compared with those managing only 10 to 11 aircraft. Moreover, the results suggest that a 70% utilization (percentage busy time) score is a valid threshold for predicting significant performance decay and could be a generalizable metric that can aid in manning predictions. This research is relevant to human supervisory control of networked military and commercial unmanned vehicles in the air, on the ground, and on and under the water.

  14. Challenges and Approaches for Developing Ultrafine Particle Emission Inventories for Motor Vehicle and Bus Fleets

    Directory of Open Access Journals (Sweden)

    Diane U. Keogh

    2011-03-01

    Full Text Available Motor vehicles in urban areas are the main source of ultrafine particles (diameters < 0.1 µm. Ultrafine particles are generally measured in terms of particle number because they have little mass and are prolific in terms of their numbers. These sized particles are of particular interest because of their ability to enter deep into the human respiratory system and contribute to negative health effects. Currently ultrafine particles are neither regularly monitored nor regulated by ambient air quality standards. Motor vehicle and bus fleet inventories, epidemiological studies and studies of the chemical composition of ultrafine particles are urgently needed to inform scientific debate and guide development of air quality standards and regulation to control this important pollution source. This article discusses some of the many challenges associated with modelling and quantifying ultrafine particle concentrations and emission rates for developing inventories and microscale modelling of motor vehicles and buses, including the challenge of understanding and quantifying secondary particle formation. Recommendations are made concerning the application of particle emission factors in developing ultrafine particle inventories for motor vehicle fleets. The article presents a précis of the first published inventory of ultrafine particles (particle number developed for the urban South-East Queensland motor vehicle and bus fleet in Australia, and comments on the applicability of the comprehensive set of average particle emission factors used in this inventory, for developing ultrafine particle (particle number and particle mass inventories in other developed countries.

  15. Vehicle rollover risk and electronic stability control systems.

    Science.gov (United States)

    MacLennan, P A; Marshall, T; Griffin, R; Purcell, M; McGwin, G; Rue, L W

    2008-06-01

    Electronic stability control (ESC) systems were developed to reduce motor vehicle collisions (MVCs) caused by loss of control. Introduced in Europe in 1995 and in the USA in 1996, ESC is designed to improve vehicle lateral stability by electronically detecting and automatically assisting drivers in unfavorable situations. To examine the relationship between vehicle rollover risk and presence of ESC using a large national database of MVCs. A retrospective cohort study for the period 1995 through 2006 was carried out using data obtained from the National Automotive Sampling System General Estimates System. All passenger cars and sport utility vehicles (SUVs)/vans of model year 1996 and later were eligible. Vehicle ESC (unavailable, optional, standard) was determined on the basis of make, model, and model year. Risk ratios (RRs) and 95% CIs were calculated to compare rollover risk by vehicle ESC group. For all crashes, vehicles equipped with standard ESC had decreased risk of rollover (RR = 0.62, 95% CI 0.50 to 0.77) compared with vehicles with ESC unavailable. The association was consistent for single-vehicle MVCs (RR = 0.61, 95% CI 0.46 to 0.82); passenger cars had decreased rollover risk (RR = 0.77, 95% CI 0.52 to 1.12), but SUVs/vans had a more dramatically decreased risk (RR = 0.40, 95% CI 0.26 to 0.61). This study supports previous results showing ESC to be effective in reducing the risk of rollover. ESC is more effective in SUVs/vans for rollovers related to single-vehicle MVCs.

  16. Diffusion of new automotive technologies for improving energy efficiency in Brazil's light vehicle fleet

    International Nuclear Information System (INIS)

    Bastin, Cristina; Szklo, Alexandre; Rosa, Luiz Pinguelli

    2010-01-01

    Historically, Brazil has promoted the development and sales of light duty vehicles running on ethanol (firstly, ethanol-dedicated cars, and recently flexfuel cars). In the 1990s, the country also favored the sales of compact cars to middle and low-income classes. However, in the last years, the profile of vehicles sold in Brazil has converged towards larger and less-efficient vehicles. In 2008, Brazil launched the vehicle labeling program. Based on the outcomes of the historical programs oriented towards the development of automotive innovations, and on a survey conducted with the country's main auto makers, this article evaluates whether the vehicle labeling program will both improve the energy efficiency of light vehicles, and introduce new technologies. Our results indicate that, despite its virtuous intentions, the program will not control the tendency of rising fuel consumption of passenger cars sold in Brazil. Therefore, other policies are needed to boost innovations in Brazil's automotive industry. (author)

  17. Development of Matlab Simulink model for dynamics analysis of passive suspension system for lightweight vehicle

    Science.gov (United States)

    Jamali, M. S.; Ismail, K. A.; Taha, Z.; Aiman, M. F.

    2017-10-01

    In designing suitable isolators to reduce unwanted vibration in vehicles, the response from a mathematical model which characterizes the transmissibility ratio of the input and output of the vehicle is required. In this study, a Matlab Simulink model is developed to study the dynamic behaviour performance of passive suspension system for a lightweight electric vehicle. The Simulink model is based on the two degrees of freedom system quarter car model. The model is compared to the theoretical plots of the transmissibility ratios between the amplitudes of the displacements and accelerations of the sprung and unsprung masses to the amplitudes of the ground, against the frequencies at different damping values. It was found that the frequency responses obtained from the theoretical calculations and from the Simulink simulation is comparable to each other. Hence, the model may be extended to a full vehicle model.

  18. Policy of developing alternate vehicles; La politique de developpement des vehicules alternatifs

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-15

    In most western cities the present-day car is by far the principal mode of transport. The wrong side of it is that automobile circulation is a source of air-pollution, noise and traffic jam, inconveniences against which public opinion shows itself more and more susceptible. Facing this situation governments in succession have since several years encouraged by different measures the development of fitted or alternative vehicles: electric, natural gas (NG) fuelled and liquefied petroleum gas (LPG) vehicles. These vehicles have the advantage of responding both to pollution problem and energy diversification challenge. The present-day regulation system gathers a number of attractive provisions: - maintaining para-fiscal taxes upon gas fuels at a level much lower than for other fuels; - VAT refunding for these gas fuels and electricity consumed by vehicles of this type; - general councils can be totally or partially exonerated from automobile taxation; - assigning future green label allowing these vehicles to be excepted from traffic restrictions applied to cope with pollution peaks. Other additional advantages are provided by the law on air and rational use of energy of 30 December 1996. Merits and drawbacks of each of the mentioned types of alternative vehicles are reviewed. So, although entirely un-polluting the electric cars are not cheap and what is even more hindering is their very limited range which for current batteries does not exceed 80 km. Only little over 3000 electric vehicles were sold, a third of them to EDF. The natural gas is rather pure a fuel at burning of which the release of sulfur and solid particles are practically negligible. Due to its characteristics, the short and medium term development of this alternative seems to reside only in buses and service vehicles, the only able to support the supplementary load of high pressure gas tanks. Being formed of liquefied butane and propane at low pressure, LPG is as attractive as NG, with respect to the

  19. From laboratory to road: Modeling the divergence between official and real-world fuel consumption and CO_2 emission values in the German passenger car market for the years 2001–2014

    International Nuclear Information System (INIS)

    Tietge, Uwe; Mock, Peter; Franco, Vicente; Zacharof, Nikiforos

    2017-01-01

    Official fuel consumption and carbon dioxide (CO_2) emission values of European passenger cars are widely recognized to be unrepresentative of real-world driving. The divergence between official and real-world values undermines national vehicle taxation schemes and EU-wide CO_2 standards for passenger cars, particularly since the divergence increases with new model generations. This study examines real-world fuel consumption data from more than 130,000 vehicles to investigate the development of the divergence. The analysis validates and refines a regression model developed by , which estimates real-world fuel consumption of cars based on readily available vehicle characteristics, namely official fuel consumption values, vehicle mass, and engine capacity. The regression model yielded coefficients of determination of 0.87 or higher, but was found to underestimate fuel consumption of newer vehicles and company cars. This study proposes to add vehicle build year as a regressor to account for the increasing divergence between official and real-world fuel consumption figures. - Highlights: • Real-world fuel consumption of new cars in Germany is 36% higher than official values. • The divergence between official and real-world fuel consumption has grown over time. • A simple regression accounts for ≥87% of the variance in real-world fuel consumption values. • Vehicle age must be included in the model to account for the growing divergence.

  20. NPS Transit System Passenger Boardings Study: Converting Ticket Sales to Passenger Boardings.

    Science.gov (United States)

    2016-01-01

    This report examines the reporting of passenger boardings (unlinked passenger trips) by NPS transit systems that use a ticket sales conversion methodology. By studying and validating the park units' passenger boarding methodology from converting tick...

  1. Mathematical modelling of active safety system functions as tools for development of driverless vehicles

    Science.gov (United States)

    Ryazantsev, V.; Mezentsev, N.; Zakharov, A.

    2018-02-01

    This paper is dedicated to a solution of the issue of synthesis of the vehicle longitudinal dynamics control functions (acceleration and deceleration control) based on the element base of the vehicle active safety system (ESP) - driverless vehicle development tool. This strategy helps to reduce time and complexity of integration of autonomous motion control systems (AMCS) into the vehicle architecture and allows direct control of actuators ensuring the longitudinal dynamics control, as well as reduction of time for calibration works. The “vehicle+wheel+road” longitudinal dynamics control is complicated due to the absence of the required prior information about the control object. Therefore, the control loop becomes an adaptive system, i.e. a self-adjusting monitoring system. Another difficulty is the driver’s perception of the longitudinal dynamics control process in terms of comfort. Traditionally, one doesn’t pay a lot of attention to this issue within active safety systems, and retention of vehicle steerability, controllability and stability in emergency situations are considered to be the quality criteria. This is mainly connected to its operational limits, since it is activated only in critical situations. However, implementation of the longitudinal dynamics control in the AMCS poses another challenge for the developers - providing the driver with comfortable vehicle movement during acceleration and deceleration - while the possible highest safety level in terms of the road grip is provided by the active safety system (ESP). The results of this research are: universal active safety system - AMCS interaction interface; block diagram for the vehicle longitudinal acceleration and deceleration control as one of the active safety system’s integrated functions; ideology of adaptive longitudinal dynamics control, which enables to realize the deceleration and acceleration requested by the AMCS; algorithms synthesised; analytical experiments proving the

  2. Real-time passenger counting by active linear cameras

    Science.gov (United States)

    Khoudour, Louahdi; Duvieubourg, Luc; Deparis, Jean-Pierre

    1996-03-01

    The companies operating subways are very much concerned with counting the passengers traveling through their transport systems. One of the most widely used systems for counting passengers consists of a mechanical gate equipped with a counter. However, such simple systems are not able to count passengers jumping above the gates. Moreover, passengers carrying large luggage or bags may meet some difficulties when going through such gates. The ideal solution is a contact-free counting system that would bring more comfort of use for the passengers. For these reasons, we propose to use a video processing system instead of these mechanical gates. The optical sensors discussed in this paper offer several advantages including well defined detection areas, fast response time and reliable counting capability. A new technology has been developed and tested, based on linear cameras. Preliminary results show that this system is very efficient when the passengers crossing the optical gate are well separated. In other cases, such as in compact crowd conditions, reasonable accuracy has been demonstrated. These results are illustrated by means of a number of sequences shot in field conditions. It is our belief that more precise measurements could be achieved, in the case of compact crowd, by other algorithms and acquisition techniques of the line images that we are presently developing.

  3. Wheelchair tiedown and occupant restraint practices in paratransit vehicles.

    Directory of Open Access Journals (Sweden)

    Karen Frost

    Full Text Available The purpose of this study was to characterize wheelchair tiedown and occupant restraint system (WTORS usage in paratransit vehicles based on observations of wheelchair and scooter (wheeled mobility devices, collectively, "WhMD" passenger trips. A retrospective review of on-board video monitoring recordings of WhMD trips was conducted. Four hundred seventy-five video recordings were collected for review and analysis. The use of all four tiedowns to secure the WhMD was observed more frequently for power WhMDs (82% and manual WhMDs (80% compared to scooters (39%, and this difference was significant (p< 0.01. Nonuse or misuse of the occupant restraint system occurred during 88% of WhMD trips, and was most frequently due to vehicle operator neglect in applying the shoulder belt. Despite the absence of incidents or injuries in this study, misuse and nonuse of WTORS potentially place WhMD seated passengers at higher risk of injury during transit. These findings support the need for improved vehicle operator training and passenger education on the proper use of WTORS and development of WTORS with improved usability and/or alternative technologies that can be automated or used independently.

  4. Thermal management of hybrid vehicles. Challenges and solutions; Thermomanagement von Hybridfahrzeugen. Herausforderungen und Loesungen

    Energy Technology Data Exchange (ETDEWEB)

    Heckenberger, T. [Behr GmbH und Co. KG, Stuttgart (Germany)

    2007-10-15

    Higher thermal management demands are placed on hybrid vehicles than on conventional vehicles. The thermal comfort of the passengers must be assured when the combustion engine shuts down, i.e. during start-stop phases and during purely electric driving. Likewise, the particular hybrid modules and components must be cooled to temperature levels that are too low for conventional cooling circuits. Behr is presently developing cooling and climate control systems for all three types of hybrid vehicles: micro-, mild, and full hybrids. (orig.)

  5. The Clean Development Mechanism as a Vehicle for Technology Transfer and Sustainable Development - Myth or Reality?

    Directory of Open Access Journals (Sweden)

    Gary Cox

    2010-09-01

    Full Text Available This paper critically examines the clean development mechanism (CDM established under Article 12 of the Kyoto Protocol in terms of its effectiveness as a vehicle for technology transfer to developing countries, a specific commitment under the UNFCCC. Fundamentally, the paper poses the question of whether technology transfer as part of the CDM is a myth or a reality in the broader context of sustainable development. Technology transfer between countries of the North and South is explored in a historical context and the emergence of technology transfer obligations is traced in multilateral environmental agreements. The architecture of the UNFCCC and the Kyoto Protocol are examined in relation to technology transfer obligations. Empirical studies are reviewed to gain an understanding of how CDM operates in practice, with a closer examination of a small number of recent CDM projects. There is an update on the Technology Mechanism being established under the Copenhagen Accord. The paper concludes with a summary of the benefits of CDM to date and its current limitations in achieving the scaling-up of affordable environmentally sound technology transfer envisaged in the Bali Action Plan. The conclusion is that technology transfer must be a much more explicit objective of CDM with better targeting of projects in order to achieve locally sustainable equitable outcomes. Furthermore, the link between CDM and technology transfer needs to be much more explicitly made in order that, in the long run, such interventions will lead to viable low emission development pathways in developing countries.

  6. Modeling Driving Performance Using In-Vehicle Speech Data From a Naturalistic Driving Study.

    Science.gov (United States)

    Kuo, Jonny; Charlton, Judith L; Koppel, Sjaan; Rudin-Brown, Christina M; Cross, Suzanne

    2016-09-01

    We aimed to (a) describe the development and application of an automated approach for processing in-vehicle speech data from a naturalistic driving study (NDS), (b) examine the influence of child passenger presence on driving performance, and (c) model this relationship using in-vehicle speech data. Parent drivers frequently engage in child-related secondary behaviors, but the impact on driving performance is unknown. Applying automated speech-processing techniques to NDS audio data would facilitate the analysis of in-vehicle driver-child interactions and their influence on driving performance. Speech activity detection and speaker diarization algorithms were applied to audio data from a Melbourne-based NDS involving 42 families. Multilevel models were developed to evaluate the effect of speech activity and the presence of child passengers on driving performance. Speech activity was significantly associated with velocity and steering angle variability. Child passenger presence alone was not associated with changes in driving performance. However, speech activity in the presence of two child passengers was associated with the most variability in driving performance. The effects of in-vehicle speech on driving performance in the presence of child passengers appear to be heterogeneous, and multiple factors may need to be considered in evaluating their impact. This goal can potentially be achieved within large-scale NDS through the automated processing of observational data, including speech. Speech-processing algorithms enable new perspectives on driving performance to be gained from existing NDS data, and variables that were once labor-intensive to process can be readily utilized in future research. © 2016, Human Factors and Ergonomics Society.

  7. Stirling engine electric hybrid vehicle propulsion system conceptual design study. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Dochat, G; Artiles, A; Killough, J; Ray, A; Chen, H S

    1978-08-01

    Results of a six-month study to characterize a series Stirling engine electric hybrid vehicle propulsion system are presented. The Stirling engine was selected as the heat conversion element to exploit the high efficiency (> .36), low pollution, multi-fuel and quiet operation of this machine. A free-piston Stirling engine driving a linear alternator in a hermatically sealed enclosure was chosen to gain the reliability, long life, and maintenance free characteristics of a sealed unit. The study performs trade off evaluations, selection of engine, battery, motor and inverter size, optimization of components, and develops a conceptual design and characterization of the total propulsion system. The conclusion of the study is that a Stirling engine electric hybrid propulsion system can be used successfully to augment the battery storage of a passenger vehicle and will result in significant savings of petroleum energy over present passenger vehicles. The performance and range augmentation of the hybrid design results in significant improvements over an all electric vehicle. The hybrid will be capable of performing 99% of the passenger vehicle annual trip distribution requirements with extremely low fuel usage. (TFD)

  8. Development of a lane change risk index using vehicle trajectory data.

    Science.gov (United States)

    Park, Hyunjin; Oh, Cheol; Moon, Jaepil; Kim, Seongho

    2018-01-01

    Surrogate safety measures (SSMs) have been widely used to evaluate crash potential, which is fundamental for the development of effective safety countermeasures. Unlike existing SSMs, which are mainly focused on the evaluation of longitudinal vehicle maneuvering leading to rear-end crashes, this study proposes a new method for estimating crash risk while a subject vehicle changes lanes, referred to as the lane change risk index (LCRI). A novel feature of the proposed methodology is its incorporation of the amount of exposure time to potential crash and the expected crash severity level by applying a fault tree analysis (FTA) to the evaluation framework. Vehicle interactions between a subject vehicle and adjacent vehicles in the starting lane and the target lane are evaluated in terms of crash potential during lane change. Vehicle trajectory data obtained from a traffic stream, photographed using a drone flown over a freeway segment, is used to investigate the applicability of the proposed methodology. This study compares the characteristics of compulsory and discretionary lane changes observed in a work zone section and a general section of a freeway using the LCRI. It is expected that the outcome of this study will be valuable in evaluating the effectiveness of various traffic operations and control strategies in terms of lane change safety. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Development of a highly maneuverable unmanned underwater vehicle on the basis of quad-copter dynamics

    Science.gov (United States)

    Amin, Osman Md; Karim, Md. Arshadul; Saad, Abdullah His

    2017-12-01

    At present, research on unmanned underwater vehicle (UUV) has become a significant & familiar topic for researchers from various engineering fields. UUV is of mainly two types - AUV (Autonomous Underwater vehicle) & ROV (Remotely Operated Vehicle). There exist a significant number of published research papers on UUV, where very few researchers emphasize on the ease of maneuvering and control of UUV. Maneuvering is important for underwater vehicle in avoiding obstacles, installing underwater piping system, searching undersea resources, underwater mine disposal operations, oceanographic surveys etc. A team from Dept. of Naval Architecture & Marine Engineering of MIST has taken a project to design a highly maneuverable unmanned underwater vehicle on the basis of quad-copter dynamics. The main objective of the research is to develop a control system for UUV which would be able to maneuver the vehicle in six DOF (Degrees of Freedom) with great ease. For this purpose we are not only focusing on controllability but also designing an efficient hull with minimal drag force & optimized propeller using CFD technique. Motors were selected on the basis of the simulated thrust generated by propellers in ANSYS Fluent software module. Settings for control parameters to carry out different types of maneuvering such as hovering, spiral, one point rotation about its centroid, gliding, rolling, drifting and zigzag motions were explained in short at the end.

  10. Research, development and demonstration of nickel-zinc batteries for electric vehicle propulsion. Annual report, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-01

    Activities in a program to develop a Ni/Zn battery for electric vehicle propulsion are reported. Aspects discussed include battery design and development, nickel cathode study, and basic electrochemistry. A number of engineering drawings are supplied. 61 figures, 11 tables. (RWR)

  11. Development of a Low-Cost Attitude Sensor for Agricultural Vehicles

    Science.gov (United States)

    The objective of this research was to develop a low-cost attitude sensor for agricultural vehicles. The attitude sensor was composed of three vibratory gyroscopes and two inclinometers. A sensor fusion algorithm was developed to estimate tilt angles (roll and pitch) by least-squares method. In the a...

  12. Certification and safety aspects relating to the transport of passengers on high altitude balloons in Europe

    Science.gov (United States)

    Schoenmaker, Annelie

    2014-07-01

    High-altitude balloons typically fly between 25 and 50 km in altitude, which, while below the Karman line of 100 km, is yet far above the altitudes typically flown by aircraft. For example, the highest-flying commercial aircraft - the Concorde - had a maximum cruising altitude of only 18 km. zero2infinity, a Spanish company, is currently developing a pressurized pod named “bloon” which will be capable of lifting six people, including two pilot crew members and four paying passengers, to an altitude of 36 km through the use of high-altitude balloons. The boundary between Airspace and Outer Space has never been legally defined, mostly because of the lack of activities taking place between the altitude where airplanes fly and the lowest orbiting spacecraft. High-altitude balloons do fly at these in-between altitudes and the prospect of commercializing access to these parts of the stratosphere poses some questions in a new light. Given the relatively low altitude at which they fly, it may well be that these types of balloons would be considered to operate exclusively within air space. However, given the technology involved in crewed high altitude balloon flights, which is more similar to spacecraft engineering than to traditional hot-air or gas ballooning, it is necessary to evaluate the various legal regimes, codes, and regulations that would apply to such flights, especially regarding licenses and liabilities. For high altitude balloon flights commencing in Europe, the European Aviation Safety Agency (EASA) would very likely be the competent certification or licensing agency for these flights, although there would likely be input from various national aviation authorities as well. However, because the European Commission (EC) has not yet issued regulations regarding commercial spaceflight, particularly the use of high altitude balloons, new rules and regulations governing such flights may still need to be drafted and promulgated. With the development of

  13. Designing Train Passenger Seat by Kansei Engineering in Indonesia

    Directory of Open Access Journals (Sweden)

    Hapsari Sakya Nabila

    2017-01-01

    Full Text Available Public transport adoption is still major problem in Indonesia. Integrating impression and emotion to service may change the image of public transport, leading to fast adoption rate. As product development technique, Kansei Engineering is well known to facilitate that integration. This paper communicates the implementation of Kansei Engineering (KE in designing train passenger seat in Indonesia. The train between Bandung-Solo (8 hours journey was chosen to be the investigated object. The train was selected to be refurbished by introducing a new passenger seat design, emphasizing on the improvement of passenger experience. As the first step of KE type I technique, travel experience of the existing passengers were taken into the consideration for selecting Kansei words. It was found that the relevant Kansei words to design passenger train seat in Indonesia were: comfort, people-friendly, multifunction, safe, soft, spacious, relaxing, superior, maintainable, strong, producible, minimalist, attractive, modern, unique, and durable. Upon understanding the semantic meaning of those words, physical properties and technical specification were produced by consulting to the related members. Finally, a passenger seat with synthetic leather cover, modular design, foldable table, individual power point, bluesilver color, and adjusted to Indonesian’s anthropometry data was proposed as the final design

  14. Effectiveness of vehicle weight enforcement in a developing country using weigh-in-motion sorting system considering vehicle by-pass and enforcement capability

    Directory of Open Access Journals (Sweden)

    Mohamed Rehan Karim

    2014-03-01

    Full Text Available Vehicle overloading has been identified as one of the major contributors to road pavement damage in Malaysia. In this study, the weigh-in-motion (WIM system has been used to function as a vehicle weight sorting tool to complement the exsiting static weigh bridge enforcement station. Data collected from the developed system is used to explore the effectiveness of using WIM system in terms of generating more accurate data for enforcement purposes and at the same time improving safety and reducing the number of vehicle weight violations on the roads. This study specifically focus on the effect of vehicle by-pass and static weigh station enforcement capability on the overall effectiveness of vehicle weight enforcement system in a developing country. Results from this study suggest that the WIM system will significantly enhance the effectiveness and efficiency of the current vehicle weight enforcement, thus generating substantial revenue that would greatly off-set the current road maintenance budget that comes from tax payers money. If there is substantial reduction in overloaded vehicles, the public will still gain through reduction in road maintenance budget, less accident risks involving heavy trucks, and lesser greenhouse gases (GHGs emissions.

  15. Design of a technology centre: A Vehicle for Industrial Development ...

    African Journals Online (AJOL)

    This paper deals with the design of a Technology Centre to meet the needs of industries and enhance the industrial development activities in Ethiopia. The article addresses problems and constraints of industries in developing countries with regards to raw materials, skills, technology master plan, R&D, maintenance and ...

  16. Mobile source CO2 mitigation through smart growth development and vehicle fleet hybridization.

    Science.gov (United States)

    Stone, Brian; Mednick, Adam C; Holloway, Tracey; Spak, Scott N

    2009-03-15

    This paper presents the results of a study on the effectiveness of smart growth development patterns and vehicle fleet hybridization in reducing mobile source emissions of carbon dioxide (CO2) across 11 major metropolitan regions of the Midwestern U.S. over a 50-year period. Through the integration of a vehicle travel activity modeling framework developed by researchers atthe Oak Ridge National Laboratory with small area population projections, we model mobile source emissions of CO2 associated with alternative land development and technology change scenarios between 2000 and 2050. Our findings suggest that under an aggressive smart growth scenario, growth in emissions expected to occur under a business as usual scenario is reduced by 34%, while the full dissemination of hybrid-electric vehicles throughout the light vehicle fleet is found to offset the expected growth in emissions by 97%. Our results further suggest that high levels of urban densification could achieve reductions in 2050 CO2 emissions equivalent to those attainable through the full dissemination of hybrid-electric vehicle technologies.

  17. Development of battery management system for nickel-metal hydride batteries in electric vehicle applications

    Science.gov (United States)

    Jung, Do Yang; Lee, Baek Haeng; Kim, Sun Wook

    Electric vehicle (EV) performance is very dependent on traction batteries. For developing electric vehicles with high performance and good reliability, the traction batteries have to be managed to obtain maximum performance under various operating conditions. Enhancement of battery performance can be accomplished by implementing a battery management system (BMS) that plays an important role in optimizing the control mechanism of charge and discharge of the batteries as well as monitoring the battery status. In this study, a BMS has been developed for maximizing the use of Ni-MH batteries in electric vehicles. This system performs several tasks: the control of charging and discharging, overcharge and over-discharge protection, the calculation and display of state-of-charge (SOC), safety, and thermal management. The BMS is installed in and tested in a DEV5-5 electric vehicle developed by Daewoo Motor Co. and the Institute for Advanced Engineering in Korea. Eighteen modules of a Panasonic nickel-metal hydride (Ni-MH) battery, 12 V, 95 A h, are used in the DEV5-5. High accuracy within a range of 3% and good reliability are obtained. The BMS can also improve the performance and cycle-life of the Ni-MH battery peak, as well as the reliability and the safety of the electric vehicles.

  18. EVC EXPO 80. Proceedings of the third international electric vehicle conference, St. Louis, MO, May 20-22, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Andrews, L.

    1980-01-01

    Issues and trends in the case of electric vehicles are considered along with vehicle systems, EV fleet user experience, batteries, aspects of vehicle testing, EV commercial market and vehicle potentials, EV cost considerations, the effective utilization of EVs, and modeling, mission analysis, and impact assessment. Attention is given to EV component reliability, automatic gearshift control for an efficient battery vehicle drive system, a brushless DC motor-power conditioner unit designed and built for propulsion of electric passenger vehicles, a roadway powered electric vehicle system, inductively coupled power systems for electric vehicles, a fuel-cell-powered golf cart, electric vehicles in telephone service, electric vehicle use in the U.S. Postal Service, high performance electric commercial vehicles, nickel iron battery design and performance, the development of the nickel-iron-battery system for electric vehicle propulsion, the advancing performance threshold of the lead-acid electric vehicle battery, advances in zinc bromine batteries for motive power, some aspects of battery vehicle evaluation with particular attention to a battery model, and a generic battery model for electric and hybrid vehicle simulation performance prediction.

  19. Energy Management of Hybrid Electric Vehicles: 15 years of development at the Ohio State University

    Directory of Open Access Journals (Sweden)

    Rizzoni Giorgio

    2015-01-01

    Full Text Available The aim of this paper is to document 15 years of hybrid electric vehicle energy management research at The Ohio State University Center for Automotive Research (OSUCAR. Hybrid Electric Vehicle (HEV technology encompasses many diverse aspects. In this paper we focus exclusively on the evolution of supervisory control strategies for on-board energy management in HEV. We present a series of control algorithms that have been developed in simulation and implemented in prototype vehicles for charge-sustaining HEVs at OSU-CAR. These solutions span from fuzzy-logic control algorithms to more sophisticated model-based optimal control methods. Finally, methods developed for plug-in HEVs energy management are also discussed

  20. DEVELOPMENT OF A GEOGRAPHIC VISUALIZATION AND COMMUNICATIONS SYSTEMS (GVCS) FOR MONITORING REMOTE VEHICLES

    Energy Technology Data Exchange (ETDEWEB)

    COLEMAN, P.; DUNCAN, M.; DURFEE, R.C.; GOELTZ, R; HARRISON, G.; HODGSON, M.E.; KOOK, M.; MCCLAIN, S.

    1998-03-30

    The purpose of this project is to integrate a variety of geographic information systems capabilities and telecommunication technologies for potential use in geographic network and visualization applications. The specific technical goals of the project were to design, develop, and simulate the components of an audio/visual geographic communications system to aid future real-time monitoring, mapping and managing of transport vehicles. The system components of this feasibility study are collectively referred to as a Geographic Visualization and Communications System (GVCS). State-of-the-art techniques will be used and developed to allow both the vehicle operator and network manager to monitor the location and surrounding environment of a transport vehicle during shipment.

  1. Testing and development of electric vehicle batteries for EPRI Electric Transportation Program

    Science.gov (United States)

    1985-11-01

    Argonne National Laboratory conducted an electric-vehicle battery testing and development program for the Electric Power Research Institute. As part of this program, eighteen battery modules previously developed by Johnson Controls, Inc. were tested. This type of battery (EV-2300 - an improved state-of-the-art lead-acid battery) was designed specifically for improved performance, range, and life in electric vehicles. In order to obtain necessary performance data, the batteries were tested under various duty cycles typical of normal service. This program, supported by the Electric Power Research Institute, consisted of three tasks: determination of the effect of cycle life vs peak power and rest period, determination of the impact of charge method on cycle life, and evaluation of the EV-2300 battery system. Two supporting studies were also carried out: one on thermal management of electric-vehicle batteries and one on enhanced utilization of active material in lead-acid batteries.

  2. A stereo vision-based obstacle detection system in vehicles

    Science.gov (United States)

    Huh, Kunsoo; Park, Jaehak; Hwang, Junyeon; Hong, Daegun

    2008-02-01

    Obstacle detection is a crucial issue for driver assistance systems as well as for autonomous vehicle guidance function and it has to be performed with high reliability to avoid any potential collision with the front vehicle. The vision-based obstacle detection systems are regarded promising for this purpose because they require little infrastructure on a highway. However, the feasibility of these systems in passenger car requires accurate and robust sensing performance. In this paper, an obstacle detection system using stereo vision sensors is developed. This system utilizes feature matching, epipoplar constraint and feature aggregation in order to robustly detect the initial corresponding pairs. After the initial detection, the system executes the tracking algorithm for the obstacles. The proposed system can detect a front obstacle, a leading vehicle and a vehicle cutting into the lane. Then, the position parameters of the obstacles and leading vehicles can be obtained. The proposed obstacle detection system is implemented on a passenger car and its performance is verified experimentally.

  3. Advancing electric-vehicle development with pure-lead-tin battery technology

    Science.gov (United States)

    O'Brien, W. A.; Stickel, R. B.; May, G. J.

    Electric-vehicle (EV) development continues to make solid progress towards extending vehicle range, reliability and ease of use, aided significantly by technological advances in vehicle systems. There is, however, a widespread misconception that current battery technologies are not capable of meeting even the minimum user requirements that would launch EVs into daily use. Existing pure-lead-tin technology is moving EVs out of research laboratories and onto the streets, in daily side-by-side operation with vehicles powered by conventional gasoline and alternative fuels. This commercially available battery technology can provide traffic-compatible performance in a reliable and affordable manner, and can be used for either pure EVs or hybrid electric vehicles (HEVs). Independent results obtained when applying lead-tin batteries in highly abusive conditions, both electrically and environmentally, are presented. The test fleet of EVs is owned and operated by Arizona Public Service (APS), an electric utility in Phoenix, AZ, USA. System, charger and battery development will be described. This gives a single charge range of up to 184 km at a constant speed of 72 km h -1, and with suitable opportunity charging, a 320 km range in a normal 8 h working day.

  4. Investigations on an energy efficient air conditioning of hybrid vehicles and electric-powered vehicles; Untersuchungen zur energieeffizienten Klimatisierung von Hybrid- und Elektrofahrzeugen

    Energy Technology Data Exchange (ETDEWEB)

    Aurich, Joerg; Baumgart, Rico; Danzer, Christoph; Unwerth, Thomas von [Technische Univ. Chemnitz (Germany). Professur Alternative Fahrzeugantriebe

    2012-11-01

    The energy-efficient air conditioning of passenger cells is an ever-increasing challenge in the development of electric vehicles because the electric heating in particular reduces the cruising range significantly. For this reason, a simulation model has been developed at Chemnitz University of Technology, which simulates the whole air conditioning system including the passenger cell and the complete powertrain in electric cars. Using this model, different optimization approaches have been analyzed and evaluated concerning the cruising range. This paper first illustrates how much the cruising range of an exemplary electric vehicle is reduced by using the electric heating under different wintery weather conditions. Afterwards, the exploitation of the waste heat produced by the powertrain components (electric motor and power electronics) will be explained. Finally, it shall be described to what extent this exploitation increases the cruising range. (orig.)

  5. ModSAF-based development of operational requirements for light armored vehicles

    Science.gov (United States)

    Rapanotti, John; Palmarini, Marc

    2003-09-01

    Light Armoured Vehicles (LAVs) are being developed to meet the modern requirements of rapid deployment and operations other than war. To achieve these requirements, passive armour is minimized and survivability depends more on sensors, computers, countermeasures and communications to detect and avoid threats. The performance, reliability, and ultimately the cost of these systems, will be determined by the technology trends and the rates at which they mature. Defining vehicle requirements will depend upon an accurate assessment of these trends over a longer term than was previously needed. Modelling and simulation are being developed to study these long-term trends and how they contribute to establishing vehicle requirements. ModSAF is being developed for research and development, in addition to the original requirement of Simulation and Modelling for Acquisition, Rehearsal, Requirements and Training (SMARRT), and is becoming useful as a means for transferring technology to other users, researchers and contractors. This procedure eliminates the need to construct ad hoc models and databases. The integration of various technologies into a Defensive Aids Suite (DAS) can be designed and analyzed by combining field trials and laboratory data with modelling and simulation. ModSAF (Modular Semi-Automated Forces,) is used to construct the virtual battlefield and, through scripted input files, a "fixed battle" approach is used to define and implement contributions from three different sources. These contributions include: models of technology and natural phenomena from scientists and engineers, tactics and doctrine from the military and detailed analyses from operations research. This approach ensures the modelling of processes known to be important regardless of the level of information available about the system. Survivability of DAS-equipped vehicles based on future and foreign technology can be investigated by ModSAF and assessed relative to a test vehicle. A vehicle can

  6. Development and demonstration of a validation methodology for vehicle lateral dynamics simulation models

    Energy Technology Data Exchange (ETDEWEB)

    Kutluay, Emir

    2013-02-01

    In this thesis a validation methodology to be used in the assessment of the vehicle dynamics simulation models is presented. Simulation of vehicle dynamics is used to estimate the dynamic responses of existing or proposed vehicles and has a wide array of applications in the development of vehicle technologies. Although simulation environments, measurement tools and mathematical theories on vehicle dynamics are well established, the methodical link between the experimental test data and validity analysis of the simulation model is still lacking. The developed validation paradigm has a top-down approach to the problem. It is ascertained that vehicle dynamics simulation models can only be validated using test maneuvers although they are aimed for real world maneuvers. Test maneuvers are determined according to the requirements of the real event at the start of the model development project and data handling techniques, validation metrics and criteria are declared for each of the selected maneuvers. If the simulation results satisfy these criteria, then the simulation is deemed ''not invalid''. If the simulation model fails to meet the criteria, the model is deemed invalid, and model iteration should be performed. The results are analyzed to determine if the results indicate a modeling error or a modeling inadequacy; and if a conditional validity in terms of system variables can be defined. Three test cases are used to demonstrate the application of the methodology. The developed methodology successfully identified the shortcomings of the tested simulation model, and defined the limits of application. The tested simulation model is found to be acceptable but valid only in a certain dynamical range. Several insights for the deficiencies of the model are reported in the analysis but the iteration step of the methodology is not demonstrated. Utilizing the proposed methodology will help to achieve more time and cost efficient simulation projects with

  7. Influence of driving cycles on exhaust emissions and fuel consumption of gasoline passenger car in Bangkok.

    Science.gov (United States)

    Nutramon, Tamsanya; Supachart, Chungpaibulpatana

    2009-01-01

    The influence of different driving cycles on their exhaust emissions and fuel consumption rate of gasoline passenger car was investigated in Bangkok based on the actual measurements obtained from a test vehicle driving on a standard chassis dynamometer. A newly established Bangkok driving cycle (BDC) and the European driving cycle (EDC) which is presently adopted as the legislative cycle for testing automobiles registered in Thailand were used. The newly developed BDC is constructed using the driving characteristic data obtained from the real on-road driving tests along selected traffic routes. A method for selecting appropriate road routes for real driving tests is also introduced. Variations of keyed driving parameters of BDC with different driving cycles were discussed. The results showed that the HC and CO emission factors of BDC are almost two and four times greater than those of EDC, respectively. Although the difference in the NOx emission factor is small, the value from BDC is still greater than that of EDC by 10%. Under BDC, the test vehicle consumes fuel about 25% more than it does under EDC. All these differences are mainly attributed to the greater proportion of idle periods and higher fluctuations of vehicle speed in the BDC cycle. This result indicated that the exhausted emissions and fuel consumption of vehicles obtained from tests under the legislative modal-type driving cycle (EDC) are significantly different from those actually produced under real traffic conditions especially during peak periods.

  8. Final Rule for Control of Air Pollution From New Motor Vehicles: Tier 2 Motor Vehicle Emissions Standards and Gasoline Sulfur Control Requirements

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) is announcing more protective tailpipe emissions standards for all passenger vehicles, including sport utility vehicles (SUVs), minivans, vans and pick-up trucks.

  9. Quality Initiatives in the Commercial Development of Reusable Launch Vehicles

    Science.gov (United States)

    2015-03-01

    projected that if the cost-escalation proceeds at the same trends, the budget allotted for the EELV program will consume most of the $7.06 billion...became necessary. Furthermore, with the emergence of the industrial society came freedom of choice for the consumer . Manufacturers now had to compete... Toyota Production System (TPS) developed by the Toyota Motor Company, where the goal of the system was to increase production efficiency by reducing

  10. Passenger flow analysis of Beijing urban rail transit network using fractal approach

    Science.gov (United States)

    Li, Xiaohong; Chen, Peiwen; Chen, Feng; Wang, Zijia

    2018-04-01

    To quantify the spatiotemporal distribution of passenger flow and the characteristics of an urban rail transit network, we introduce four radius fractal dimensions and two branch fractal dimensions by combining a fractal approach with passenger flow assignment model. These fractal dimensions can numerically describe the complexity of passenger flow in the urban rail transit network and its change characteristics. Based on it, we establish a fractal quantification method to measure the fractal characteristics of passenger follow in the rail transit network. Finally, we validate the reasonability of our proposed method by using the actual data of Beijing subway network. It has been shown that our proposed method can effectively measure the scale-free range of the urban rail transit network, network development and the fractal characteristics of time-varying passenger flow, which further provides a reference for network planning and analysis of passenger flow.

  11. Dynamic Passenger Assignment during Disruptions in Railway Systems

    NARCIS (Netherlands)

    Zhu, Y.; Goverde, R.M.P.

    2017-01-01

    Passenger-oriented rescheduling problems receive increasing attention. However, the passenger assignment models used for evaluating the rescheduling solutions are usually simplified by many assumptions. To estimate passenger inconvenience more accurately, this paper establishes a dynamic passenger

  12. A road safety performance indicator for vehicle fleet compatibility.

    Science.gov (United States)

    Christoph, Michiel; Vis, Martijn Alexander; Rackliff, Lucy; Stipdonk, Henk

    2013-11-01

    This paper discusses the development and the application of a safety performance indicator which measures the intrinsic safety of a country's vehicle fleet related to fleet composition. The indicator takes into account both the 'relative severity' of individual collisions between different vehicle types, and the share of those vehicle types within a country's fleet. The relative severity is a measure for the personal damage that can be expected from a collision between two vehicles of any type, relative to that of a collision between passenger cars. It is shown how this number can be calculated using vehicle mass only. A sensitivity analysis is performed to study the dependence of the indicator on parameter values and basic assumptions made. The indicator is easy to apply and satisfies the requirements for appropriate safety performance indicators. It was developed in such a way that it specifically scores the intrinsic safety of a fleet due to its composition, without being influenced by other factors, like helmet wearing. For the sake of simplicity, and since the required data is available throughout Europe, the indicator was applied to the relative share of three of the main vehicle types: passenger cars, heavy goods vehicles and motorcycles. Using the vehicle fleet data from 13EU Member States and Norway, the indicator was used to rank the countries' safety performance. The UK was found to perform best in terms of its fleet composition (value is 1.07), while Greece has the worst performance with the highest indicator value (1.41). Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Development of on-board vehicle measurements for emergency situations

    International Nuclear Information System (INIS)

    Dollo, R.; Renier, S.; Testini, Y.; Sontag, M.

    1992-01-01

    In case of accident in a nuclear power plant, measurements must be carried out very quickly around the site, in order to control and limit the consequences for the population. Measurements which have the priority are the gamma dose rate, the total beta activity, the gamma activity due to I 131 (charcoal filter) and due to Cs 134/137 (paper filter). To fulfill the requirement, EDF has developed and selected necessary equipment, putting the emphasis on the reliability and on the ease of use. A computer-controlled system dedicated to dose rate measurement and gamma spectroscopy is described, as well as an autonomous programmable, air and water-sampling device. (author)

  14. Development of a Vehicle Awareness Module for Bicycles

    OpenAIRE

    Sequeira, Charlene

    2017-01-01

    Autonomous driving is one of the car industry’s major challenges. The next generation of cars will not be driven by humans, but by the cars themselves. With the increase in the number of self driving cars, the pedestrians and bikers need to be walk and bike carefully. Bikers need to be careful even now, when we have human driven cars. While driving, sometimes a bike can be in the blind spot of the car and hence go unnoticed. In this thesis, a small scale prototype was developed to help the bi...

  15. Conceptual Feasibility Study of the Hyperloop Vehicle for Next-Generation Transport

    Science.gov (United States)

    Decker, Kenneth; Chin, Jeffrey; Peng, Andi; Summers, Colin; Nguyen, Golda; Oberlander, Andrew; Sakib, Gazi; Sharifrazi, Nariman; Heath, Christopher; Gray, Justin S.; hide

    2017-01-01

    The Hyperloop concept is proposed as a faster, cheaper alternative to high-speed rail and traditional short-haul aircraft. It consists of a passenger pod traveling through a tube under light vacuum while being propelled and levitated by a combination of permanent and electro-magnets. The concept addresses NASA's research thrusts for growth in demand, sustainability, and technology convergence for high-speed transport. Hyperloop is a radical departure from other advanced aviation concepts, however it remains an aeronautics concept that tackles the same strategic goals of low-carbon propulsion and ultra-effcient vehicles. System feasibility was investigated by building a multidisciplinary vehicle sizing model that takes into account aerodynamic, thermodynamic, structures, electromagnetic, weight, and mission analyses. The sizing process emphasized the strong coupling between the two largest systems: the tube and the passenger pod. The model was then exercised to examine Hyperloop from a technical and cost perspective. The structural sizing analysis of the travel tube demonstrates potential for signi cant capital cost reductions by considering an underwater route. Examination of varying passenger capacity indicates that the system can be operated with a wide range of passenger loads without significant change in operating expenses. Lastly, a high-level sizing study simulated variations in tube area, pressure, pod speed, and passenger capacity showing that there is a tube pressure that minimizes operating energy usage. The value of this optimal tube pressure is highly sensitive to numerous design details. These combined estimates of energy consumption, passenger throughput, and mission analyses all support Hyperloop as a faster and cheaper alternative to short-haul flights. The tools and expertise used to quantify these results also demonstrate how traditional aerospace design methods can be leveraged to handle the complex and coupled design process. Much of the

  16. Development of a control model for a four wheel mecanum vehicle

    CSIR Research Space (South Africa)

    De Villiers, M

    2010-07-01

    Full Text Available Page 1 of 10 25th International Conference of CAD/CAM, Robotics & Factories of the Future Conference, 13-16 July 2010, Pretoria, South Africa DEVELOPMENT OF A CONTROL MODEL FOR A FOUR WHEEL MECANUM VEHICLE M. de Villiers1, Prof. G. Bright2... and summed to get the following equations (1)(2) defining the total force applied to the vehicle, the subscript T is applied to show that these are total forces: g1832g3021g3051 g2191 g3404 g3533 g1832g3051g3050 g2191 g2781 g2205g2880g2778 (1...

  17. Development of Anti-lock Braking System (ABS) for Vehicles Braking

    Science.gov (United States)

    Minh, Vu Trieu; Oamen, Godwin; Vassiljeva, Kristina; Teder, Leo

    2016-11-01

    This paper develops a real laboratory of anti-lock braking system (ABS) for vehicle and conducts real experiments to verify the ability of this ABS to prevent the vehicle wheel from being locked while braking. Two controllers of PID and fuzzy logic are tested for analysis and comparison. This ABS laboratory is designed for bachelor and master students to simulate and analyze performances of ABS with different control techniques on various roads and load conditions. This paper provides educational theories and practices on the design of control for system dynamics.

  18. Super-capacitors fuel-cell hybrid electric vehicle optimization and control strategy development

    International Nuclear Information System (INIS)

    Paladini, Vanessa; Donateo, Teresa; De Risi, Arturo; Laforgia, Domenico

    2007-01-01

    In the last decades, due to emissions reduction policies, research focused on alternative powertrains among which hybrid electric vehicles (HEVs) powered by fuel cells are becoming an attractive solution. One of the main issues of these vehicles is the energy management in order to improve the overall fuel economy. The present investigation aims at identifying the best hybrid vehicle configuration and control strategy to reduce fuel consumption. The study focuses on a car powered by a fuel cell and equipped with two secondary energy storage devices: batteries and super-capacitors. To model the powertrain behavior an on purpose simulation program called ECoS has been developed in Matlab/Simulink environment. The fuel cell model is based on the Amphlett theory. The battery and the super-capacitor models account for charge/discharge efficiency. The analyzed powertrain is also equipped with an energy regeneration system to recover braking energy. The numerical optimization of vehicle configuration and control strategy of the hybrid electric vehicle has been carried out with a multi objective genetic algorithm. The goal of the optimization is the reduction of hydrogen consumption while sustaining the battery state of charge. By applying the algorithm to different driving cycles, several optimized configurations have been identified and discussed

  19. Developing particulate thin filter using coconut fiber for motor vehicle emission

    Science.gov (United States)

    Wardoyo, A. Y. P.; Juswono, U. P.; Riyanto, S.

    2016-03-01

    Amounts of motor vehicles in Indonesia have been recognized a sharply increase from year to year with the increment reaching to 22 % per annum. Meanwhile motor vehicles produce particulate emissions in different sizes with high concentrations depending on type of vehicles, fuels, and engine capacity. Motor Particle emissions are not only to significantly contribute the atmosphric particles but also adverse to human health. In order to reduce the particle emission, it is needed a filter. This study was aimed to develop a thin filter using coconut fiber to reduce particulate emissions for motor vehicles. The filter was made of coconut fibers that were grinded into power and mixed with glues. The filter was tested by the measurements of particle concentrations coming out from the vehicle exhaust directly and the particle concentrations after passing through the filter. The efficiency of the filter was calculated by ratio of the particle concentrations before comming in the filter to the particle conentrations after passing through the filter. The results showed that the efficiency of the filter obtained more than 30 %. The efficiency increases sharply when a number of the filters are arranged paralelly.

  20. Electric personnel carrier introduced : RES Equipment Sales spearheads development of electric underground vehicle

    International Nuclear Information System (INIS)

    Tollinsky, N.

    2010-01-01

    RES Equipment Sales of Dryden, Ontario is leading the development of a battery-powered personnel utility vehicle for underground mining applications. Among the advantages of the battery-powered personnel carrier are quietness of the carrier and zero emissions, which eliminates particulates from diesel engines and reduces the need for ventilation. This article discussed the design and building of the vehicle. It was designed to accommodate up to 3 battery packs, depending on the frequency of use. Swapping batteries takes between 2 or 3 minutes. Spent batteries must be plugged in for 6 hours and rest for another 6 to 8 hours before being ready for service. The vehicle accommodates 2 or 3 people and travels at speeds of 6 to 8 miles per hour. This article also provided background information on RES Equipment Sales. The company remanufactures underground mining equipment, including load-haul-dump machines, jumbos, haul trucks and utility vehicles. In addition, the company sells and services new equipment, including Oldenburg Cannon jumbos, scalers and utility vehicles, as well as Canun International pneumatic rock drills and NPK rock breakers. 1 ref., 1 fig.

  1. Development of database of real-world diesel vehicle emission factors for China.

    Science.gov (United States)

    Shen, Xianbao; Yao, Zhiliang; Zhang, Qiang; Wagner, David Vance; Huo, Hong; Zhang, Yingzhi; Zheng, Bo; He, Kebin

    2015-05-01

    A database of real-world diesel vehicle emission factors, based on type and technology, has been developed following tests on more than 300 diesel vehicles in China using a portable emission measurement system. The database provides better understanding of diesel vehicle emissions under actual driving conditions. We found that although new regulations have reduced real-world emission levels of diesel trucks and buses significantly for most pollutants in China, NOx emissions have been inadequately controlled by the current standards, especially for diesel buses, because of bad driving conditions in the real world. We also compared the emission factors in the database with those calculated by emission factor models and used in inventory studies. The emission factors derived from COPERT (Computer Programmer to calculate Emissions from Road Transport) and MOBILE may both underestimate real emission factors, whereas the updated COPERT and PART5 (Highway Vehicle Particulate Emission Modeling Software) models may overestimate emission factors in China. Real-world measurement results and emission factors used in recent emission inventory studies are inconsistent, which has led to inaccurate estimates of emissions from diesel trucks and buses over recent years. This suggests that emission factors derived from European or US-based models will not truly represent real-world emissions in China. Therefore, it is useful and necessary to conduct systematic real-world measurements of vehicle emissions in China in order to obtain the optimum inputs for emission inventory models. Copyright © 2015. Published by Elsevier B.V.

  2. Energy demand and greenhouse gas emissions during the production of a passenger car in China

    International Nuclear Information System (INIS)

    Yan Xiaoyu

    2009-01-01

    Rapidly-rising oil demand and associated greenhouse gas (GHG) emissions from road vehicles in China, passenger cars in particular, have attracted worldwide attention. As most studies to date were focused on the vehicle operation stage, the present study attempts to evaluate the energy demand and GHG emissions during the vehicle production process, which usually consists of two major stages-material production and vehicle assembly. Energy demand and GHG emissions in the material production stage are estimated using the following data: the mass of the vehicle, the distribution of material used by mass, and energy demand and GHG emissions associated with the production of each material. Energy demand in the vehicle assembly stage is estimated as a linear function of the vehicle mass, while the associated GHG emission is estimated according to the primary energy sources. It is concluded that the primary energy demand, petroleum demand and GHG emissions during the production of a medium-sized passenger car in China are 69,108 MJ, 14,545 MJ and 6575 kg carbon dioxide equivalent (CO 2 -eq). Primary energy demand, petroleum demand and GHG emissions in China's passenger car fleets in 2005 would be increased by 22%, 5% and 30%, respectively, if the vehicle production stage were included.

  3. Development of an extended-range electric vehicle : a systems engineering approach

    NARCIS (Netherlands)

    Voorderhake, S.F.

    2013-01-01

    This report presents the complete design (i.e., from product level to implementation level) of a sportive hatchback extended-range electric vehicle, including the design rationales and product creation process used. The project had two main goals: First, the development of a modular extended-range

  4. Development of a new formulation combining calcipotriol and betamethasone dipropionate in an ointment vehicle

    DEFF Research Database (Denmark)

    Simonsen, Lene; Høy, Gert; Didriksen, Erik

    2004-01-01

    was to develop a formulation which combines calcipotriol and betamethasone dipropionate in a single vehicle hereby achieving optimal delivery of both substances into the skin. As the two substances are incompatible in aqueous and alcoholic medias, different non-aqueous formulations were prepared. Skin permeation...

  5. Passengers, Crowding and Complexity : Models for passenger oriented public transport

    NARCIS (Netherlands)

    P.C. Bouman (Paul)

    2017-01-01

    markdownabstractPassengers, Crowding and Complexity was written as part of the Complexity in Public Transport (ComPuTr) project funded by the Netherlands Organisation for Scientific Research (NWO). This thesis studies in three parts how microscopic data can be used in models that have the potential

  6. Design and Development of the Engine Unit for a Twin-Rotor Unmanned Aerial Vehicle

    Directory of Open Access Journals (Sweden)

    G. Avanzini

    2005-01-01

    Full Text Available Advanced computer-aided technologies played a crucial role in the design of an unconventional Uninhabited Aerial Vehicle (UAV, developed at the Turin Technical University and the University of Rome “La Sapienza”. The engine unit of the vehicle is made of a complex system of three two stroke piston engines coupled with two counter-rotating three-bladed rotors, controlled by rotary PWM servos. The focus of the present paper lies on the enabling technologies exploited in the framework of activities aimed at designing a suitable and reliable engine system, capable of performing the complex tasks required for operating the proposed rotorcraft. The synergic use of advanced computational tools for estimating the aerodynamic performance of the vehicle, solid modeling for mechanical components design, and rapid prototyping techniques for control system logic synthesis and implementation will be presented. 

  7. A trade-off analysis design tool. Aircraft interior noise-motion/passenger satisfaction model

    Science.gov (United States)

    Jacobson, I. D.

    1977-01-01

    A design tool was developed to enhance aircraft passenger satisfaction. The effect of aircraft interior motion and noise on passenger comfort and satisfaction was modelled. Effects of individual aircraft noise sources were accounted for, and the impact of noise on passenger activities and noise levels to safeguard passenger hearing were investigated. The motion noise effect models provide a means for tradeoff analyses between noise and motion variables, and also provide a framework for optimizing noise reduction among noise sources. Data for the models were collected onboard commercial aircraft flights and specially scheduled tests.

  8. 19 CFR 4.50 - Passenger lists.

    Science.gov (United States)

    2010-04-01

    ... VESSELS IN FOREIGN AND DOMESTIC TRADES Passengers on Vessels § 4.50 Passenger lists. (a) The master of... passenger and crew lists, as required by § 4.7(a) of this part. If the vessel is arriving from noncontiguous... 19 Customs Duties 1 2010-04-01 2010-04-01 false Passenger lists. 4.50 Section 4.50 Customs Duties...

  9. Human Factors Engineering in Designing the Passengers' Cockpit of the Malaysian Commercial Suborbital Spaceplane

    Science.gov (United States)

    Ridzuan Zakaria, Norul; Mettauer, Adrian; Abu, Jalaluddin; Hassan, Mohd Roshdi; Ismail, Anwar Taufeek; Othman, Jamaluddin; Shaari, Che Zhuhaida; Nasron, Nasri

    2010-09-01

    The design of the passengers’ cabin or cockpit of commercial suborbital spaceplane is a new and exciting frontier in human factors engineering, which emphasizes on comfort and safety. There is a program to develop small piloted 3 seats commercial suborbital spaceplane by a group of Malaysians with their foreign partners, and being relatively small and due to its design philosophy, the spaceplane does not require a cabin, but only a cockpit for its 2 passengers. In designing the cockpit, human factors engineering and safety principles are given priority. The cockpit is designed with the intention to provide comfort and satisfaction to the passengers without compromising the safety, in such a way that there are passenger-view wide angled video camera to observe the passengers at all time in flight, “rear-view”, “under-the-floor-view” and “fuselage-view” video cameras for the passengers, personalized gauges and LCDs on the dashboard to provide vital and useful information during the flight to the passengers, and biomedical engineered products which not only entertain the passengers, but also provide important information on the passengers to the ground crews who are responsible in the comfort and safety of the passengers. The passenger-view video-camera, which record the passengers with Earth visible through the glass canopy as the background, not only provides live visual of the passengers for safety reason, but also provide the most preferred memorable video collection for the passengers, while other video cameras provide the opportunity to view at various angles from unique positions to both the passengers and the ground observers. The gauges and LCDs on the dashboard provide access to the passengers to information such as the gravity, orientation, rate of climb and flight profile of the spaceplane, graphical presentation of the spaceplane in flight, and live video from the onboard video cameras. There is also a control stick for each passenger to

  10. Power-based electric vehicle energy consumption model: Model development and validation

    International Nuclear Information System (INIS)

    Fiori, Chiara; Ahn, Kyoungho; Rakha, Hesham A.

    2016-01-01

    Highlights: • The study developed an instantaneous energy consumption model (VT-CPEM) for EVs. • The model captures instantaneous braking energy regeneration. • The model can be used for transportation modeling and vehicle applications (e.g. eco-routing). • The proposed model can be easily calibrated using publically available EV data. • Usages of air conditioning and heating systems reduce EV energy consumption by up to 10% and 24%, respectively. - Abstract: The limited drive range (The maximum distance that an EV can travel.) of Electric Vehicles (EVs) is one of the major challenges that EV manufacturers are attempting to overcome. To this end, a simple, accurate, and efficient energy consumption model is needed to develop real-time eco-driving and eco-routing systems that can enhance the energy efficiency of EVs and thus extend their travel range. Although numerous publications have focused on the modeling of EV energy consumption levels, these studies are limited to measuring energy consumption of an EV’s control algorithm, macro-project evaluations, or simplified well-to-wheels analyses. Consequently, this paper addresses this need by developing a simple EV energy model that computes an EV’s instantaneous energy consumption using second-by-second vehicle speed, acceleration and roadway grade data as input variables. In doing so, the model estimates the instantaneous braking energy regeneration. The proposed model can be easily implemented in the following applications: in-vehicle, Smartphone eco-driving, eco-routing and transportation simulation software to quantify the network-wide energy consumption levels for a fleet of EVs. One of the main advantages of EVs is their ability to recover energy while braking using a regenerative braking system. State-of-the-art vehicle energy consumption models consider an average constant regenerative braking energy efficiency or regenerative braking factors that are mainly dependent on the vehicle’s average

  11. THE RISK OF INJURY AND VEHICLE DAMAGE SEVERITY IN VEHICLE MISMATCHED SIDE IMPACT CRASHES IN BRITISH COLUMBIA

    Directory of Open Access Journals (Sweden)

    Ediriweera DESAPRIYA

    2005-01-01

    Full Text Available As occupant protection offered by new passenger vehicles has improved, there has been growing concern about the harm that some vehicle designs may inflict on occupants of other vehicles with which they collide. Preceding analyses of crash statistics have clearly demonstrated the incompatibility between passenger sedan cars (PS and pick-up trucks (PU involved in side impact crashes in British Columbia. A comparison of light truck and passenger car crashes in previous literature reveals that light truck vehicles inflict greater harm than passenger cars for a number of reasons including their greater weight, stiffer structure, and higher ride height. These features place occupants of passenger cars at a disadvantage should they be involved in a collision with a light truck vehicle. The injury risk for passenger sedan car occupants is greater than the risk for pick-up truck occupants in two-vehicle crashes (Odds Ratio (OR 1.87; 95% Confidence Interval (CI 1.38-2.52. In addition, the risk of vehicle damage severity was increased for passenger cars compared with pick-up trucks (write off vehicle-OR 5.35; 95% CI 3.75-7.63, severely damaged vehicles-OR 5.87; 95% CI 4.79–7.19, moderately damaged vehicles-OR 2.86; 95% CI 2.44–3.36. There is strong justification for injury prevention experts and policy makers to step up motor vehicle crash injury prevention advocacy by implementing evidence-based policies to reduce rates of injury as a result of passenger sedan cars and pick-up trucks involved in side impact crashes in the province of British Columbia.

  12. Trade-off results and preliminary designs of Near-Term Hybrid Vehicles

    Science.gov (United States)

    Sandberg, J. J.

    1980-01-01

    Phase I of the Near-Term Hybrid Vehicle Program involved the development of preliminary designs of electric/heat engine hybrid passenger vehicles. The preliminary designs were developed on the basis of mission analysis, performance specification, and design trade-off studies conducted independently by four contractors. THe resulting designs involve parallel hybrid (heat engine/electric) propulsion systems with significant variation in component selection, power train layout, and control strategy. Each of the four designs is projected by its developer as having the potential to substitute electrical energy for 40% to 70% of the petroleum fuel consumed annually by its conventional counterpart.

  13. A Large-Scale Design Integration Approach Developed in Conjunction with the Ares Launch Vehicle Program

    Science.gov (United States)

    Redmon, John W.; Shirley, Michael C.; Kinard, Paul S.

    2012-01-01

    This paper presents a method for performing large-scale design integration, taking a classical 2D drawing envelope and interface approach and applying it to modern three dimensional computer aided design (3D CAD) systems. Today, the paradigm often used when performing design integration with 3D models involves a digital mockup of an overall vehicle, in the form of a massive, fully detailed, CAD assembly; therefore, adding unnecessary burden and overhead to design and product data management processes. While fully detailed data may yield a broad depth of design detail, pertinent integration features are often obscured under the excessive amounts of information, making them difficult to discern. In contrast, the envelope and interface method results in a reduction in both the amount and complexity of information necessary for design integration while yielding significant savings in time and effort when applied to today's complex design integration projects. This approach, combining classical and modern methods, proved advantageous during the complex design integration activities of the Ares I vehicle. Downstream processes, benefiting from this approach by reducing development and design cycle time, include: Creation of analysis models for the Aerodynamic discipline; Vehicle to ground interface development; Documentation development for the vehicle assembly.

  14. Energy Chain Analysis of Passenger Car Transport

    Directory of Open Access Journals (Sweden)

    Hans Jakob Walnum

    2011-02-01

    Full Text Available Transport makes up 20 percent of the World’s energy use; in OECD countries this has exceeded 30 percent. The International Energy Agency (IEA estimates that the global energy consumption will increase by 2.1 percent annually, a growth rate that is higher than for any other sector. The high energy consumption means that transportation accounts for nearly 30 percent of CO2 emission in OECD countries and is also one of the main sources of regional and local air pollution. In this article, we analyze energy consumption and greenhouse gas emissions from passenger car transport using an energy chain analysis. The energy chain analysis consists of three parts: the net direct energy use, the energy required for vehicle propulsion; the gross direct chain, which includes the net direct energy consumption plus the energy required to produce it; and, finally, the indirect energy chain, which includes the energy consumption for production, maintenance and operation of infrastructure plus manufacturing of the vehicle itself. In addition to energy consumption, we also analyze emissions of greenhouse gases measured by CO2-equivalents. We look at the trade-offs between energy use and greenhouse gas emissions to see whether some drivetrains and fuels perform favourable on both indicators. Except for the case of electric cars, where hydropower is the only energy source in the Norwegian context, no single car scores favourably on both energy consumption and greenhouse gas emissions.

  15. Development of natural gas vehicles in China: An assessment of enabling factors and barriers

    International Nuclear Information System (INIS)

    Wang, Hongxia; Fang, Hong; Yu, Xueying; Wang, Ke

    2015-01-01

    Replacing conventional gasoline or diesel vehicles with natural gas vehicles (NGVs) is necessary if China hopes to significantly reduce its greenhouse gas emissions in the short term. Based on city-level data, this paper analyzes the enabling factors and barriers to China's NGV development. We find that a shortage in natural gas supply and a relatively high price ratio of natural gas compared to gasoline are the main factors impeding China's NGV development. Imbalanced development between natural gas refueling stations and NGVs also hinder the popularity of these lower-carbon vehicles. While various policies have been implemented in recent years to promote NGVs in China, only those encouraging adoption of NGVs by the private sector appear effective. To promote further NGV development in China, the following strategies are proposed: (1) improve natural gas delivery infrastructure across the country; (2) reasonably reduce the relative price of natural gas compared to gasoline; (3) give priority to middle-income and medium-sized cities and towns, since siting natural gas refueling stations is easier in these areas; and (4) promote the use of NGVs in the private sector. -- Highlights: •We assess the effectiveness of NGV policies in China. •Relatively low natural gas price promotes NGV development. •Coordinated development of refueling stations and NGVs is important. •Policies that encourage private NGV development should be adopted. •Middle-income and medium-sized cities are more suitable for developing NGVs

  16. Computational Fluid Dynamic Analysis of Enhancing Passenger Cabin Comfort Using PCM

    Science.gov (United States)

    Purusothaman, M.; Valarmathi, T. N.; Dada Mohammad, S. K.

    2016-09-01

    The main purpose of this study is to determine a cost effective way to enhance passenger cabin comfort by analyzing the effect of solar radiation of a open parked vehicle, which is exposed to constant solar radiation on a hot and sunny day. Maximum heat accumulation occurs in the car cabin due to the solar radiation. By means of computational fluid dynamics (CFD) analysis, a simulation process is conducted for the thermal regulation of the passenger cabin using a layer of phase change material (PCM) on the roof structure of a stationary car when exposed to ambient temperature on a hot sunny day. The heat energy accumulated in the passenger cabin is absorbed by a layer of PCM for phase change process. The installation of a ventilation system which uses an exhaust fan to create a natural convection scenario in the cabin is also considered to enhance passenger comfort along with PCM.

  17. Commercial Passenger Fishing Vessel Fishery

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains the logbook data from U.S.A. Commercial Passenger Fishing Vessels (CPFV) fishing in the U.S.A. EEZ and in waters off of Baja California, from...

  18. Quasi steady-state aerodynamic model development for race vehicle simulations

    Science.gov (United States)

    Mohrfeld-Halterman, J. A.; Uddin, M.

    2016-01-01

    Presented in this paper is a procedure to develop a high fidelity quasi steady-state aerodynamic model for use in race car vehicle dynamic simulations. Developed to fit quasi steady-state wind tunnel data, the aerodynamic model is regressed against three independent variables: front ground clearance, rear ride height, and yaw angle. An initial dual range model is presented and then further refined to reduce the model complexity while maintaining a high level of predictive accuracy. The model complexity reduction decreases the required amount of wind tunnel data thereby reducing wind tunnel testing time and cost. The quasi steady-state aerodynamic model for the pitch moment degree of freedom is systematically developed in this paper. This same procedure can be extended to the other five aerodynamic degrees of freedom to develop a complete six degree of freedom quasi steady-state aerodynamic model for any vehicle.

  19. International foodborne outbreak of Shigella sonnei infection in airline passengers.

    Science.gov (United States)

    Gaynor, K; Park, S Y; Kanenaka, R; Colindres, R; Mintz, E; Ram, P K; Kitsutani, P; Nakata, M; Wedel, S; Boxrud, D; Jennings, D; Yoshida, H; Tosaka, N; He, H; Ching-Lee, M; Effler, P V

    2009-03-01

    During 22-24 August 2004, an outbreak of Shigella sonnei infection affected air travellers who departed from Hawaii. Forty-seven passengers with culture-confirmed shigellosis and 116 probable cases who travelled on 12 flights dispersed to Japan, Australia, 22 US states, and American Samoa. All flights were served by one caterer. Pulsed-field gel electrophoresis of all 29 S. sonnei isolates yielded patterns that matched within one band. Food histories and menu reviews identified raw carrot served onboard as the likely vehicle of infection. Attack rates for diarrhoea on three surveyed flights with confirmed cases were 54% (110/204), 32% (20/63), and 12% (8/67). A total of 2700 meals were served on flights with confirmed cases; using attack rates observed on surveyed flights, we estimated that 300-1500 passengers were infected. This outbreak illustrates the risk of rapid, global spread of illness from a point-source at a major airline hub.

  20. National Motor Vehicle Crash Causation Survey (NMVCCS) - NMVCCS XML Case Viewer

    Data.gov (United States)

    Department of Transportation — The National Motor Vehicle Crash Causation Survey (NMVVCS) was a nationwide survey of crashes involving light passenger vehicles, with a focus on the factors related...

  1. Research, development, and demonstration of nickel-zinc batteries for electric vehicle propulsion. Annual report for 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-03-01

    Progress in the development of nickel-zinc batteries for electric vehicles is reported. Information is presented on nickel electrode preparation and testing; zinc electrode preparation with additives and test results; separator development and the evaluation of polymer-blend separator films; sealed Ni-Zn cells; and the optimization of electric vehicle-type Ni-Zn cells. (LCL)

  2. Regional disparity of urban passenger transport associated GHG (greenhouse gas) emissions in China: A review

    International Nuclear Information System (INIS)

    Hao, Han; Geng, Yong; Wang, Hewu; Ouyang, Minggao

    2014-01-01

    With China’s urbanization and motorization, greenhouse gas (GHG) emissions from urban passenger transport increased rapidly over recent years. As we estimated, China’s urban passenger transport associated motorized travel, energy consumption and lifecycle GHG emissions reached 2815 billion passenger kilometers (pkm), 77 million tons of oil equivalent (toe) and 335 million ton CO 2 equivalent in 2010, over half of which were located in eastern provinces. Over national level, GHG emissions by private passenger vehicles, business passenger vehicles, taxis, motorcycles, E-bikes, transit buses and urban rails accounted for 57.7%, 13.0%, 7.7%, 8.6%, 1.8%, 10.5% and 0.7% of the total. Significant regional disparity was observed. The province-level per capita GHG emissions ranged from 285 kg/capita in Guizhou to 1273 kg/capita in Beijing, with national average of 486 kg/capita. Depending on province context and local policy orientation, the motorization pathways of China’s several highest motorized provinces are quite diverse. We concluded that motorization rate and transport structure were the substantial factors determining urban passenger transport associated GHG emissions. Considering the great potential of urban passenger transport growth in China, policies guiding the optimization of transport structure should be in place with priority in eastern provinces. - Highlights: • Province-leveled motorized travel, energy consumption and GHG emissions in China were studied. • Significant regional disparities on urban passenger transport were observed. • Region-specific sustainable transport energy policies were discussed

  3. Development of Pneumatic Aerodynamic Devices to Improve the Performance, Economics, and Safety of Heavy Vehicles

    International Nuclear Information System (INIS)

    Robert J. Englar

    2000-01-01

    Under contract to the DOE Office of Heavy Vehicle Technologies, the Georgia Tech Research Institute (GTRI) is developing and evaluating pneumatic (blown) aerodynamic devices to improve the performance, economics, stability and safety of operation of Heavy Vehicles. The objective of this program is to apply the pneumatic aerodynamic aircraft technology previously developed and flight-tested by GTRI personnel to the design of an efficient blown tractor-trailer configuration. Recent experimental results obtained by GTRI using blowing have shown drag reductions of 35% on a streamlined automobile wind-tunnel model. Also measured were lift or down-load increases of 100-150% and the ability to control aerodynamic moments about all 3 axes without any moving control surfaces. Similar drag reductions yielded by blowing on bluff afterbody trailers in current US trucking fleet operations are anticipated to reduce yearly fuel consumption by more than 1.2 billion gallons, while even further reduction is possible using pneumatic lift to reduce tire rolling resistance. Conversely, increased drag and down force generated instantaneously by blowing can greatly increase braking characteristics and control in wet/icy weather due to effective ''weight'' increases on the tires. Safety is also enhanced by controlling side loads and moments caused on these Heavy Vehicles by winds, gusts and other vehicles passing. This may also help to eliminate the jack-knifing problem if caused by extreme wind side loads on the trailer. Lastly, reduction of the turbulent wake behind the trailer can reduce splash and spray patterns and rough air being experienced by following vehicles. To be presented by GTRI in this paper will be results developed during the early portion of this effort, including a preliminary systems study, CFD prediction of the blown flowfields, and design of the baseline conventional tractor-trailer model and the pneumatic wind-tunnel model

  4. Development of Pneumatic Aerodynamic Devices to Improve the Performance, Economics, and Safety of Heavy Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Robert J. Englar

    2000-06-19

    Under contract to the DOE Office of Heavy Vehicle Technologies, the Georgia Tech Research Institute (GTRI) is developing and evaluating pneumatic (blown) aerodynamic devices to improve the performance, economics, stability and safety of operation of Heavy Vehicles. The objective of this program is to apply the pneumatic aerodynamic aircraft technology previously developed and flight-tested by GTRI personnel to the design of an efficient blown tractor-trailer configuration. Recent experimental results obtained by GTRI using blowing have shown drag reductions of 35% on a streamlined automobile wind-tunnel model. Also measured were lift or down-load increases of 100-150% and the ability to control aerodynamic moments about all 3 axes without any moving control surfaces. Similar drag reductions yielded by blowing on bluff afterbody trailers in current US trucking fleet operations are anticipated to reduce yearly fuel consumption by more than 1.2 billion gallons, while even further reduction is possible using pneumatic lift to reduce tire rolling resistance. Conversely, increased drag and down force generated instantaneously by blowing can greatly increase braking characteristics and control in wet/icy weather due to effective ''weight'' increases on the tires. Safety is also enhanced by controlling side loads and moments caused on these Heavy Vehicles by winds, gusts and other vehicles passing. This may also help to eliminate the jack-knifing problem if caused by extreme wind side loads on the trailer. Lastly, reduction of the turbulent wake behind the trailer can reduce splash and spray patterns and rough air being experienced by following vehicles. To be presented by GTRI in this paper will be results developed during the early portion of this effort, including a preliminary systems study, CFD prediction of the blown flowfields, and design of the baseline conventional tractor-trailer model and the pneumatic wind-tunnel model.

  5. A Passenger Travel Demand Model for Copenhagen

    DEFF Research Database (Denmark)

    Overgård, Christian Hansen; Jovicic, Goran

    2003-01-01

    The passenger travel model for Copenhagen is a state-of-practice nested logit model in which the sub-models - i.e. generation, distribution and mode choice models - are connected via measure of accessibility. The model includes in its structure a large set of explanatory variables at all three...... aims to provide a detailed description of the model, which can be used as a guide to the future development of similar models. Also, an application of the model in a study of road pricing in denmark is described. This gives the reader an idea of how such a policy measure can be modelled as well...

  6. Black carbon and polycyclic aromatic hydrocarbon emissions from vehicles in the United States-Mexico border region: pilot study.

    Science.gov (United States)

    Kelly, Kerry; Wagner, David; Lighty, JoAnn; Quintero Núñez, Margarito; Vazquez, F Adrian; Collins, Kimberly; Barud-Zubillaga, Alberto

    2006-03-01

    The investigators developed a system to measure black carbon (BC) and particle-bound polycyclic aromatic hydrocarbon (PAH) emission factors during roadside sampling in four cities along the United States-Mexico border, Calexico/Mexicali and El Paso/Juarez. The measurement system included a photoacoustic analyzer for BC, a photoelectric aerosol sensor for particle-bound PAHs, and a carbon dioxide (CO2) analyzer. When a vehicle with measurable emissions passed the system probe, corresponding BC, PAH, and CO2 peaks were evident, and a fuel-based emission factor was estimated. A picture of each vehicle was also recorded with a digital camera. The advantage of this system, compared with other roadside methods, is the direct measurement of particulate matter components and limited interference from roadside dust. The study revealed some interesting trends: Mexican buses and all medium-duty trucks were more frequently identified as high emitters of BC and PAH than heavy-duty trucks or passenger vehicles. In addition, because of the high daily mileage of buses, they are good candidates for additional study. Mexican trucks and buses had higher average emission factors compared with U.S. trucks and buses, but the differences were not statistically significant. Few passenger vehicles had measurable BC and PAH emissions, although the highest emission factor came from an older model passenger vehicle licensed in Baja California.

  7. Telemedical Advice to Long Distance Passenger Ferries

    DEFF Research Database (Denmark)

    Jensen, Olaf Chresten; Bøggild, Niels Bo; Kristensen, Søren

    consultations with passenger ferries to identify areas for possible improvements. Methods: Data from the journals for one year from Radio Medical Denmark consultations with the medical Data from the journals for one year from Radio Medical Denmark consultations with the medical responsible officers on passenger...... ferries was analysed retrospectively. Results: Two hundred and fourteen RM records, 73% among passenger and 27% among crewmember Two hundred and fourteen RM records, 73% among passenger and 27% among crewmember patients were analysed. Passenger patients were generally older and more serious ill than...

  8. Determinants of injuries in passenger vessel accidents.

    Science.gov (United States)

    Yip, Tsz Leung; Jin, Di; Talley, Wayne K

    2015-09-01

    This paper investigates determinants of crew and passenger injuries in passenger vessel accidents. Crew and passenger injury equations are estimated for ferry, ocean cruise, and river cruise vessel accidents, utilizing detailed data of individual vessel accidents that were investigated by the U.S. Coast Guard during the time period 2001-2008. The estimation results provide empirical evidence (for the first time in the literature) that crew injuries are determinants of passenger injuries in passenger vessel accidents. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Impact of aftertreatment devices and driving conditions on unregulated emissions for Euro 5 vehicles

    OpenAIRE

    LIU, Yao; LOUIS, Cédric; GORIAUX, Mathieu; CHAUMOND, Agnès; TASSEL, Patrick; PERRET, Pascal; ANDRE, Michel

    2016-01-01

    Road traffic is a major contributor of air pollution in urban areas and particularly passenger cars. To reduce regulated emissions, new aftertreatment devices and new technologies were developed (catalysed or additived Diesel particle filter, direct injected gasoline vehicle...). These new technologies induce modifications of unregulated emissions (VOC, BTEX, PAH, NO2, black carbon, metals, ultrafine particles). Unregulated pollutants might induce many health effects regarding their toxicity ...

  10. Modelling and hardware-in-the-loop simulation of the blowout tract components for passenger compartment air conditioning of motor vehicles; Modellierung und Hardware-in-the-Loop-Simulation der Komponenten des Ausblastraktes zur Kraftfahrzeuginnenraumklimatisierung

    Energy Technology Data Exchange (ETDEWEB)

    Michalek, David

    2009-07-01

    The author investigated the modelling and hardware-in-the-loop simulation of components of the blowout tract of motor car air conditioning systems. The control systems and air conditioning systems are gone into, from the air entering the car to the control systems and sensors for monitoring state variables. The function of the control equipment hardware and software was to be analyzed reproducibly in order to save time and cost. The models were verified using available data. Validation criteria were established for the hardware-in-the-loop simulator. On the basis of selected operating conditions, the performance of the air conditioning control unit inside the vehicle was compared with the simulation results and was evaluated on the basis of the established criteria. (orig.)

  11. Reducing deaths in single vehicle collisions.

    NARCIS (Netherlands)

    Adminaite, D. Jost, G. Stipdonk, H. & Ward, H.

    2017-01-01

    A third of road deaths in the EU are caused by collisions that involve a single motorised vehicle where the driver, rider and/or passengers are killed but no other road users are involved. These single vehicle collisions (SVCs), and how to prevent them occurring, are the subject of this report.

  12. Carbon monoxide levels in popular passenger commuting modes traversing major commuting routes in Hong Kong

    International Nuclear Information System (INIS)

    Chan, L.Y.; Liu, Y.M.

    2001-01-01

    Vehicle exhaust is a major source of air pollution in metropolitan cities. Commuters are exposed to high traffic-related pollutant concentrations. Public transportation is the most popular commuting mode in Hong Kong and there are about 10.8 million passenger trips every day. Two-thirds of them are road commuters. An extensive survey was conducted to measure carbon monoxide in three popular passenger commuting modes, bus, minibus, and taxi, which served, respectively, 3.91 million, 1.76 million and 1.31 million passenger trips per day in 1998. Three types of commuting microenvironments were selected: urban-urban, urban-suburban and urban-rural. Results indicated that in-vehicle CO level increased in the following order: bus, minibus and taxi. The overall average in-vehicle CO level in air-conditioned bus, minibus and taxi were 1.8, 2.9 and 3.3ppm, respectively. The average concentration level between air-conditioned buses (1.8ppm) and non-air-conditioned buses (1.9ppm) was insignificant. The fluctuation of in-vehicle CO level of non-air-conditioned vehicle followed the variation of out-vehicle CO concentration. Our result also showed that even in air-conditioned vehicles, the in-vehicle CO concentration was affected by the out-vehicle CO concentration although there exists a smoothing out effect. The in-vehicle CO level was the highest in urban-suburban commuting routes and was followed by urban-urban routes. The in-vehicle CO level in urban-rural routes was the lowest. The highest CO level was recorded after the vehicle traversed through tunnel.. The average CO exposure level of public road transportation commuters in Honk Kong was lower than most other cities. Factors governing the CO levels were also discussed. (Author)

  13. A Comprehensive Structural Dynamic Analysis Approach for Multi Mission Earth Entry Vehicle (MMEEV) Development

    Science.gov (United States)

    Perino, Scott; Bayandor, Javid; Siddens, Aaron

    2012-01-01

    The anticipated NASA Mars Sample Return Mission (MSR) requires a simple and reliable method in which to return collected Martian samples back to earth for scientific analysis. The Multi-Mission Earth Entry Vehicle (MMEEV) is NASA's proposed solution to this MSR requirement. Key aspects of the MMEEV are its reliable and passive operation, energy absorbing foam-composite structure, and modular impact sphere (IS) design. To aid in the development of an EEV design that can be modified for various missions requirements, two fully parametric finite element models were developed. The first model was developed in an explicit finite element code and was designed to evaluate the impact response of the vehicle and payload during the final stage of the vehicle's return to earth. The second model was developed in an explicit code and was designed to evaluate the static and dynamic structural response of the vehicle during launch and reentry. In contrast to most other FE models, built through a Graphical User Interface (GUI) pre-processor, the current model was developed using a coding technique that allows the analyst to quickly change nearly all aspects of the model including: geometric dimensions, material properties, load and boundary conditions, mesh properties, and analysis controls. Using the developed design tool, a full range of proposed designs can quickly be analyzed numerically and thus the design trade space for the EEV can be fully understood. An engineer can then quickly reach the best design for a specific mission and also adapt and optimize the general design for different missions.

  14. Heavy-Duty Vehicle Port Drayage Drive Cycle Characterization and Development

    Energy Technology Data Exchange (ETDEWEB)

    Prohaska, Robert; Konan, Arnaud; Kelly, Kenneth; Lammert, Michael

    2016-10-06

    In an effort to better understand the operational requirements of port drayage vehicles and their potential for adoption of advanced technologies, National Renewable Energy Laboratory (NREL) researchers collected over 36,000 miles of in-use duty cycle data from 30 Class 8 drayage trucks operating at the Port of Long Beach and Port of Los Angeles in Southern California. These data include 1-Hz global positioning system location and SAE J1939 high-speed controller area network information. Researchers processed the data through NREL's Drive-Cycle Rapid Investigation, Visualization, and Evaluation tool to examine vehicle kinematic and dynamic patterns across the spectrum of operations. Using the k-medoids clustering method, a repeatable and quantitative process for multi-mode drive cycle segmentation, the analysis led to the creation of multiple drive cycles representing four distinct modes of operation that can be used independently or in combination. These drive cycles are statistically representative of real-world operation of port drayage vehicles. When combined with modeling and simulation tools, these representative test cycles allow advanced vehicle or systems developers to efficiently and accurately evaluate vehicle technology performance requirements to reduce cost and development time while ultimately leading to the commercialization of advanced technologies that meet the performance requirements of the port drayage vocation. The drive cycles, which are suitable for chassis dynamometer testing, were compared to several existing test cycles. This paper presents the clustering methodology, accompanying results of the port drayage duty cycle analysis and custom drive cycle creation.

  15. Heavy-Duty Vehicle Port Drayage Drive Cycle Characterization and Development: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Prohaska, Robert; Konan, Arnaud; Kelly, Kenneth; Lammert, Michael

    2016-08-01

    In an effort to better understand the operational requirements of port drayage vehicles and their potential for adoption of advanced technologies, National Renewable Energy Laboratory (NREL) researchers collected over 36,000 miles of in-use duty cycle data from 30 Class 8 drayage trucks operating at the Port of Long Beach and Port of Los Angeles in Southern California. These data include 1-Hz global positioning system location and SAE J1939 high-speed controller area network information. Researchers processed the data through NREL's Drive-Cycle Rapid Investigation, Visualization, and Evaluation tool to examine vehicle kinematic and dynamic patterns across the spectrum of operations. Using the k-medoids clustering method, a repeatable and quantitative process for multi-mode drive cycle segmentation, the analysis led to the creation of multiple drive cycles representing four distinct modes of operation that can be used independently or in combination. These drive cycles are statistically representative of real-world operation of port drayage vehicles. When combined with modeling and simulation tools, these representative test cycles allow advanced vehicle or systems developers to efficiently and accurately evaluate vehicle technology performance requirements to reduce cost and development time while ultimately leading to the commercialization of advanced technologies that meet the performance requirements of the port drayage vocation. The drive cycles, which are suitable for chassis dynamometer testing, were compared to several existing test cycles. This paper presents the clustering methodology, accompanying results of the port drayage duty cycle analysis and custom drive cycle creation.

  16. Advances in the development of ovonic nickel metal hydride batteries for industrial and electric vehicles

    International Nuclear Information System (INIS)

    Venkatesan, S.; Fetcenko, M.A.; Dhar, S.K.; Ovshinsky, S.R.

    1991-01-01

    This paper reports that increasing concerns over urban pollution and continued uncertainties about oil supplies have forced the government and industry to refocus their attention on electric vehicles. Despite enormous expenditures in research and development for the ideal battery system, no commercially viable candidate has emerged. The battery systems being considered today due to renewed environmental concerns are still the same systems that were so extensively tested over the last 15 years. For immediate application, an electric vehicle designer has very little choice other than the lead-acid battery despite the fact that energy density is so low as to make vehicle range inadequate, as well as the need for replacement every 20,000 miles. The high energy density projections of Na-S and other so-called high energy batteries have proven to be significantly less in practical modules and there are still concern over cycle life which can be attained under aggressive conditions, reliability under freeze/thaw cycling and consequences resulting from high temperature operation. The conventional nickel-based systems (Ni- Zn, Ni-Fe, Ni-Cd) provide near term higher energy density as compared to lead-acid, but still do not address other important issues such as long life, the need for maintenance-free operation, the use of nontoxic materials and low cost. Against this background, the development of Ovonic Nickel-Metal Hydride (Ni-MH) batteries for electric vehicles has been rapid and successful. Ovonic No-Mh battery technology is uniquely qualified for electric vehicles due to its high energy density, high discharge rate capability, non-toxic alloys, long cycle life. low cost, tolerance to abuse and ability to be sealed for totally maintenance free operation

  17. Sustainable passenger road transport scenarios to reduce fuel consumption, air pollutants and GHG (greenhouse gas) emissions in the Mexico City Metropolitan Area

    International Nuclear Information System (INIS)

    Chavez-Baeza, Carlos; Sheinbaum-Pardo, Claudia

    2014-01-01

    This paper presents passenger road transport scenarios that may assist the MCMA (Mexico City Metropolitan Area) in achieving lower emissions in both criteria air pollutants (CO, NO x , NMVOC (non-methane volatile organic compounds), and PM 10 ) and GHG (greenhouse gas) (CH 4 , N 2 O and CO 2 ), while also promoting better mobility and quality of life in this region. We developed a bottom-up model to estimate the historical trends of energy demand, criteria air pollutants and GHG emissions caused by passenger vehicles circulating in the Mexico City Metropolitan Area (MCMA) in order to construct a baseline scenario and two mitigation scenarios that project their impact to 2028. Mitigation scenario “eff” considers increasing fuel efficiencies and introducing new technologies for vehicle emission controls. Mitigation scenario “BRT” considers a modal shift from private car trips to a Bus Rapid Transport system. Our results show significant reductions in air pollutants and GHG emissions. Incentives and environmental regulations are needed to enable these scenarios. - Highlights: • More than 4.2 million passenger vehicles in the MCMA (Mexico City Metropolitan Area) that represent 61% of criteria pollutants and 44% of GHG (greenhouse gas) emissions. • Emissions of CO, NO x and NMVOC (non-methane volatile organic compounds) in baseline scenario decrease with respect to its 2008 value because emission standards. • Emissions of PM 10 and GHG increase in baseline scenario. • Emissions of PM 10 and GHG decrease in eff + BRT scenario from year 2020. • Additional reductions are possible with better standards for diesel vehicles and other technologies

  18. CAD/CAE-technologies application for assessment of passenger safety on railway transport in emergency

    Science.gov (United States)

    Antipin, D. Ya; Shorokhov, S. G.; Bondarenko, O. I.

    2018-03-01

    A possibility of using current software products realizing CAD/CAE-technologies for the assessment of passenger safety in emergency cases on railway transport has been analyzed. On the basis of the developed solid computer model of an anthropometric dummy, the authors carried out an analysis of possible levels of passenger injury during accident collision of a train with an obstacle.

  19. Reusable launch vehicles, enabling technology for the development of advanced upper stages and payloads

    International Nuclear Information System (INIS)

    Metzger, John D.

    1998-01-01

    In the near future there will be classes of upper stages and payloads that will require initial operation at a high-earth orbit to reduce the probability of an inadvertent reentry that could result in a detrimental impact on humans and the biosphere. A nuclear propulsion system, such as was being developed under the Space Nuclear Thermal Propulsion (SNTP) Program, is an example of such a potential payload. This paper uses the results of a reusable launch vehicle (RLV) study to demonstrate the potential importance of a Reusable Launch Vehicle (RLV) to test and implement an advanced upper stage (AUS) or payload in a safe orbit and in a cost effective and reliable manner. The RLV is a horizontal takeoff and horizontal landing (HTHL), two-stage-to-orbit (TSTO) vehicle. The results of the study shows that an HTHL is cost effective because it implements airplane-like operation, infrastructure, and flight operations. The first stage of the TSTO is powered by Rocket-Based-Combined-Cycle (RBCC) engines, the second stage is powered by a LOX/LH rocket engine. The TSTO is used since it most effectively utilizes the capability of the RBCC engine. The analysis uses the NASA code POST (Program to Optimize Simulated Trajectories) to determine trajectories and weight in high-earth orbit for AUS/advanced payloads. Cost and reliability of an RLV versus current generation expandable launch vehicles are presented

  20. Development of Bird-like Micro Aerial Vehicle with Flapping and Feathering Wing Motions

    Science.gov (United States)

    Maglasang, Jonathan; Goto, Norihiro; Isogai, Koji

    To investigate the feasibility of a highly efficient flapping system capable of avian maneuvers, such as rapid takeoff, hover and gliding, a full scale bird-like (ornithopter) flapping-wing micro aerial vehicle (MAV) shaped and patterned after a typical pigeon (Columba livia) has been designed and constructed. Both numerical and experimental methods have been used in the development of this vehicle. This flapping-wing micro aerial vehicle utilizes both the flapping and feathering motions of an avian wing by employing a novel flapping-feathering mechanism, which has been synthesized and constructed so as to best describe the properly coordinated flapping and feathering wing motions at phase angle difference of 90° in a horizontal steady level flight condition. This design allows high flapping and feathering amplitudes and is configurable for asymmetric wing motions which are desirable in high-speed flapping flight and maneuvering. The preliminary results indicate its viability as a practical and an efficient flapping-wing micro aerial vehicle.