WorldWideScience

Sample records for passenger car pm

  1. Diesel passenger car PM emissions: From Euro 1 to Euro 4 with particle filter

    Science.gov (United States)

    Tzamkiozis, Theodoros; Ntziachristos, Leonidas; Samaras, Zissis

    2010-03-01

    This paper examines the impact of the emission control and fuel technology development on the emissions of gaseous and, in particular, PM pollutants from diesel passenger cars. Three cars in five configurations in total were measured, and covered the range from Euro 1 to Euro 4 standards. The emission control ranged from no aftertreatment in the Euro 1 case, an oxidation catalyst in Euro 2, two oxidation catalysts and exhaust gas recirculation in Euro 3 and Euro 4, while a catalyzed diesel particle filter (DPF) fitted in the Euro 4 car led to a Euro 4 + DPF configuration. Both certification test and real-world driving cycles were employed. The results showed that CO and HC emissions were much lower than the emission standard over the hot-start real-world cycles. However, vehicle technologies from Euro 2 to Euro 4 exceeded the NOx and PM emission levels over at least one real-world cycle. The NOx emission level reached up to 3.6 times the certification level in case of the Euro 4 car. PM were up to 40% and 60% higher than certification level for the Euro 2 and Euro 3 cars, while the Euro 4 car emitted close or slightly below the certification level over the real-world driving cycles. PM mass reductions from Euro 1 to Euro 4 were associated with a relevant decrease in the total particle number, in particular over the certification test. This was not followed by a respective reduction in the solid particle number which remained rather constant between the four technologies at 0.86 × 10 14 km -1 (coefficient of variation 9%). As a result, the ratio of solid vs. total particle number ranged from ˜50% in Euro 1-100% in Euro 4. A significant reduction of more than three orders of magnitude in solid particle number is achieved with the introduction of the DPF. However, the potential for nucleation mode formation at high speed from the DPF car is an issue that needs to be considered in the over all assessment of its environmental benefit. Finally, comparison of the

  2. Exposure to particulate matter in traffic: A comparison of cyclists and car passengers

    Science.gov (United States)

    Int Panis, Luc; de Geus, Bas; Vandenbulcke, Grégory; Willems, Hanny; Degraeuwe, Bart; Bleux, Nico; Mishra, Vinit; Thomas, Isabelle; Meeusen, Romain

    2010-06-01

    Emerging evidence suggests that short episodes of high exposure to air pollution occur while commuting. These events can result in potentially adverse health effects. We present a quantification of the exposure of car passengers and cyclists to particulate matter (PM). We have simultaneously measured concentrations (PNC, PM2.5 and PM10) and ventilatory parameters (minute ventilation (VE), breathing frequency and tidal volume) in three Belgian locations (Brussels, Louvain-la-Neuve and Mol) for 55 persons (38 male and 17 female). Subjects were first driven by car and then cycled along identical routes in a pairwise design. Concentrations and lung deposition of PNC and PM mass were compared between biking trips and car trips. Mean bicycle/car ratios for PNC and PM are close to 1 and rarely significant. The size and magnitude of the differences in concentrations depend on the location which confirms similar inconsistencies reported in literature. On the other hand, the results from this study demonstrate that bicycle/car differences for inhaled quantities and lung deposited dose are large and consistent across locations. These differences are caused by increased VE in cyclists which significantly increases their exposure to traffic exhaust. The VE while riding a bicycle is 4.3 times higher compared to car passengers. This aspect has been ignored or severely underestimated in previous studies. Integrated health risk evaluations of transport modes or cycling policies should therefore use exposure estimates rather than concentrations.

  3. Environmental assessment of speeding up use of particle filters on passenger cars and vans. Air quality and population exposure for PM{sub 2.5}; Miljoevurdering af fremskyndelse af partikelfiltre pae person- og varebiler. Luftkvalitet og befolkningseksponering for PM{sub 2.5}

    Energy Technology Data Exchange (ETDEWEB)

    Solvang Jensen, S.; Ketzel, M. [DMU, Afd. for Atmosfaerisk Miljoe (Denmark)

    2006-11-15

    New stringent European Union emission standards for particles are expected to be implemented around 2010 for diesel-powered passenger cars and vans. Provided that such standards are agreed upon diesel-powered passenger cars and vans are expected to be equipped with particle filters that effectively will remove particle emissions. Against this background, the Danish Environmental Assessment Institute wanted to carry out a cost-benefit analysis of a scenario where the emission standards came into force in 2007 instead of 2010. The objective of the project is to assess the effects on particle emissions and air quality of PM{sub 2.5} (particles less than 2.5 micrometer) of moving forward the emission standards for passenger cars and vans. An assessment of a scenario is carried out that assumes that all new diesel-powered passenger cars and vans entering the vehicle fleet during January 1st, 2007 and December 31st, 2009 will be equipped with particle filters. The National Environmental Research Institute has carried out this assessment. (au)

  4. 49 CFR 223.15 - Requirements for existing passenger cars.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Requirements for existing passenger cars. 223.15... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION SAFETY GLAZING STANDARDS-LOCOMOTIVES, PASSENGER CARS AND CABOOSES Specific Requirements § 223.15 Requirements for existing passenger cars. (a) Passenger cars built or...

  5. Passenger car fuel consumption survey

    Energy Technology Data Exchange (ETDEWEB)

    1984-03-01

    This survey originated from a proposal to monitor the fuel consumption and fuel economy of personal use passenger cars operated in Canada. Its purpose is to establish a data base which would contain information on total distance travelled, total amount of fuel consumed, average distance obtained per unit of fuel, total expenditures on fuel, and seasonal fluctuations in fuel consumption and in distance travelled. Among the needs served by this data base are the monitoring of passenger car fuel economy standards and the estimation of pasenger car fuel requirements in conditions involving fuel shortages. Survey methodology is by telephone interview to trace selected vehicles to the registered owners, at which time a fuel purchase diary is then mailed to the principal driver of the car. The results are tabulated on a quarterly basis and to be released as they become available in bulletins similar to this. Data are presented for each province and the total for Canada is given. During the fourth quarter of 1982, it is estimated that there were 7.3 million personal use passenger cars operated in Canada. These cars were driven 28 billion kilometers and consumed 4.3 billion litres of fuel. Their average litres/100 kilometres and the average fuel consumption was 590 litres. 8 tabs.

  6. Energy Use of Passenger Cars

    DEFF Research Database (Denmark)

    Jørgensen, Kaj

    1998-01-01

    Analysis of the Danish sale and stock of passenger cars, focusing particularly on aspects influencing energy use. The project has tracked the development of vehicle weight, power and fuel economy for both the sale of new cars (from 1980 to 1997)and the stock. In addition, the energy use...

  7. 49 CFR 223.17 - Identification of equipped locomotives, passenger cars and cabooses.

    Science.gov (United States)

    2010-10-01

    ... cars and cabooses. 223.17 Section 223.17 Transportation Other Regulations Relating to Transportation...-LOCOMOTIVES, PASSENGER CARS AND CABOOSES Specific Requirements § 223.17 Identification of equipped locomotives, passenger cars and cabooses. Each locomotive, passenger car and caboose that is fully equipped with glazing...

  8. CONCEPT OF THE MINIMUM ENERGY PASSENGER CAR WITH USE OF UNCONVENTIONAL ENERGY SOURCES

    Directory of Open Access Journals (Sweden)

    V. A. Gabrinets

    2014-06-01

    Full Text Available Purpose. The paper is aimed to consider the concept of creation of the minimum energy passenger car with use of nonconventional energy sources and the walls that have enhanced thermal insulation properties. Мethodology. The types of heat losses, as well as their value were analyzed. The alternative sources of energy are considered for heating. Their potential contribution to the overall energy balance of the passenger car is analyzed. Impact on the car design of the enhanced wall thermal insulation, solar energy inflow through the transparent windows and energy release of passengers are quantitatively evaluated. Findings. With the maximum possible use of all unconventional energy sources and the rational scheme solutions of conditioning and heating systems energy the costs for these needs for a passenger car can be reduced by 40-50%. Originality. New types of energy to maintain the heat balance of the car in the winter period is proposed to use firstly. New schematics solutions for environmental control system of the car both in winter and in summer periods were offered. Practical value. Introduction of the proposed scheme solutions and approaches to ensure the comfortable conditions for passengers may be implemented on an existing park of passenger cars and do not require a major re-equipment of systems that have already been installed.

  9. The effect of extended periodic inspection of passenger cars and vans

    DEFF Research Database (Denmark)

    Pilegaard, Ninette; Bernhoft, Inger Marie

    The purpose of this note is to perform a calculation of the costs and benefits of extended period-ic inspection of passenger cars and vans in Denmark, provided that the first inspection of pas-senger cars and vans is performed after four years, then one inspection after two years and thereafter...

  10. Influence of Unsteady Aerodynamics on Driving Dynamics of Passenger Cars

    OpenAIRE

    Huemer, J.; Stickel, T.; Sagan, E.; Schwarz, M.; Wall, W.A.

    2015-01-01

    Recent approaches towards numerical investigations with CFD-Methods on unsteady aerodynamic loads of passenger cars identified major differences compared to steady state aerodynamic excitations. Furthermore innovative vehicle concepts like electric-vehicles or hybrid drives further challenge the basic layout of passenger cars. Therefore the relevance of unsteady aerodynamic loads on cross-wind stability of changing basic vehicle architectures should be analysed. In order to assure and improve...

  11. MATHEMATICAL MODEL OF UNSTEADY HEAT TRANSFER OF PASSENGER CAR WITH HEATING SYSTEM

    Directory of Open Access Journals (Sweden)

    E. V. Biloshytskyi

    2018-02-01

    Full Text Available Purpose. The existing mathematical models of unsteady heat processes in a passenger car do not fully reflect the thermal processes, occurring in the car wits a heating system. In addition, unsteady heat processes are often studied in steady regime, when the heat fluxes and the parameters of the thermal circuit are constant and do not depend on time. In connection with the emergence of more effective technical solutions to the life support system there is a need for creating a new mathematical apparatus, which would allow taking into account these features and their influence on the course of unsteady heat processes throughout the travel time. The purpose of this work is to create a mathematical model of the heat regime of a passenger car with a heating system that takes into account the unsteady heat processes. Methodology. To achieve this task the author composed a system of differential equations, describing unsteady heat processes during the heating of a passenger car. For the solution of the composed system of equations, the author used the method of elementary balances. Findings. The paper presents the developed numerical algorithm and computer program for simulation of transitional heat processes in a locomotive traction passenger car, which allows taking into account the various constructive solutions of the life support system of passenger cars and to simulate unsteady heat processes at any stage of the trip. Originality. For the first time the author developed a mathematical model of heat processes in a car with a heating system, that unlike existing models, allows to investigate the unsteady heat engineering performance in the cabin of the car under different operating conditions and compare the work of various life support systems from the point of view their constructive solutions. Practical value. The work presented the developed mathematical model of the unsteady heat regime of the passenger car with a heating system to estimate

  12. Scenarios for regional passenger car fleets and their CO2 emissions

    International Nuclear Information System (INIS)

    Meyer, Ina; Kaniovski, Serguei; Scheffran, Jürgen

    2012-01-01

    Passenger car traffic is among the main contributors to anthropogenic greenhouse gas (GHG) emissions, which are responsible for climate change. It is also an important indicator used to forecast these emissions in integrated climate-economic models. This paper develops scenarios for global passenger car stock until 2050. The study adopts a global regionalized approach, encompassing 11 world regions. Car stock projections are obtained using a multi-model approach, which includes a consumer demand model based on utility maximization, a non-linear Gompertz model and a panel estimate of the income elasticity of demand for cars. The main hypothesis underlying these projections is that preferences for purchasing cars are similar across cultures and nations and that the demand for cars is largely determined by disposable income. We apply scenarios for the average traffic volume and fuel efficiency developed in previous work together with the average carbon content of fuels to obtain the CO 2 emissions. - Research highlights: ► This study develops scenarios for global passenger car stock, CO 2 emissions and fuel efficiency until 2050. ► In a global regionalized approach car stock projections are obtained using a multi-model approach. ► Compared are utility maximization, a non-linear Gompertz model and a panel estimate. ► Preferences for purchasing cars are similar across cultures and nations. ► The demand for cars is largely determined by disposable income.

  13. Research on some auxiliary mechanisms used in passenger cars

    Science.gov (United States)

    Antonescu, Daniela; Iozsa, Daniel; Antonescu, Ovidiu; Fratila, Gh.

    2017-10-01

    The paper presents the results of researches on the topological structure and geometrical analysis of the planar mechanisms with articulated bars, which are used for actuating the doors of cars. The main five types of car doors with rotate movement (folding) are presented, being described both as constructive structure and mode of operation, through suitable kinematic schemes. Some innovative solutions for vehicle door actuating mechanisms aim to use as little space as possible, which is beneficial for car parking. There are three types of car door movements: rotation, sliding and planar rotational-sliding. Most of the cars are equipped with folding doors, where the rotate movement is limited and operates horizontally. Almost all sliding doors are placed on the rear of the car (only for passengers, not for driver). Unlike rotate doors, the sliding doors require a minimum lateral space, which is an advantage, especially in parking places. In the end of the paper, a kinematic analysis of the canopy 4-bar mechanism has been performed, in order to increase the passenger comfort on the access into the vehicle.

  14. Structure and impacts of fuel economy standards for passenger cars in China

    International Nuclear Information System (INIS)

    Wagner, David Vance; An Feng; Wang Cheng

    2009-01-01

    By the end of 2006, there were about 24 million total passenger cars on the roads in China, nearly three times as many as in 2001. To slow the increase in energy consumption by these cars, China began implementing passenger car fuel economy standards in two phases beginning in 2005. Phase 1 fuel consumption limits resulted in a sales-weighted new passenger car average fuel consumption decrease of about 11%, from just over 9 l/100 km to approximately 8 l/100 km, from 2002 to 2006. However, we project that upon completion of Phase 2 limits in 2009, the average fuel consumption of new passenger cars in China may drop only by an additional 1%, to approximately 7.9 l/100 km. This is due to the fact that a majority of cars sold in 2006 already meets the stricter second phase fuel consumption limits. Simultaneously, other trends in the Chinese vehicle market, including increases in average curb weight and increases in standards-exempt imported vehicles, threaten to offset the efficiency gains achieved from 2002 to 2006. It is clear that additional efforts and policies beyond Phase 2 fuel consumption limits are required to slow and, ultimately, reverse the trend of rapidly rising energy consumption and greenhouse gases from China's transportation sector.

  15. General principles of control method of passenger car bodies bending vibration parameters

    Science.gov (United States)

    Skachkov, A. N.; Samoshkin, S. L.; Korshunov, S. D.; Kobishchanov, V. V.; Antipin, D. Ya

    2018-03-01

    Weight reduction of passenger cars is a promising direction of reducing the cost of their production and increasing transportation profitability. One way to reduce the weight of passenger cars is the lightweight metal body design by means of using of high-strength aluminum alloys, low-alloy and stainless steels. However, it has been found that the limit of the lightweight metal body design is not determined by the total mode of deformation, but its flexural rigidity, as the latter influences natural frequencies of body bending vibrations. With the introduction of mandatory certification for compliance with the Customs Union technical regulations, the following index was confirmed: “first natural frequency of body bending vibrations in the vertical plane”. This is due to the fact that vibration, noise and car motion depend on this index. To define the required indexes, the principles of the control method of bending vibration parameters of passenger car bodies are proposed in this paper. This method covers all stages of car design – development of design documentation, manufacturing and testing experimental and pilot models, launching the production. The authors also developed evaluation criteria and the procedure of using the results for introduction of control method of bending vibration parameters of passenger car bodies.

  16. Small passenger car transmission test-Chevrolet 200 transmission

    Science.gov (United States)

    Bujold, M. P.

    1980-01-01

    The small passenger car transmission was tested to supply electric vehicle manufacturers with technical information regarding the performance of commerically available transmissions which would enable them to design a more energy efficient vehicle. With this information the manufacturers could estimate vehicle driving range as well as speed and torque requirements for specific road load performance characteristics. A 1979 Chevrolet Model 200 automatic transmission was tested per a passenger car automatic transmission test code (SAE J651b) which required drive performance, coast performance, and no load test conditions. The transmission attained maximum efficiencies in the mid-eighty percent range for both drive performance tests and coast performance tests. Torque, speed and efficiency curves map the complete performance characteristics for Chevrolet Model 200 transmission.

  17. CO2 emissions change from the sales authorization of diesel passenger cars: Korean case study

    International Nuclear Information System (INIS)

    Jeong, Suk Jae; Kim, Kyung Sup; Park, Jin-Won

    2009-01-01

    The climatic change is a matter of grave concern to the whole world. As a countermeasure against the climatic change convention, the Korean government has authorized the sale of diesel passenger cars since 2005. In this paper, we analyze the effects of the sales authorization of diesel passenger cars in its role as a countermeasure. Their share, carbon emissions, and pollutant emissions of each type of passenger car are analyzed using system dynamics. The result is that the carbon emissions are decreased by 5.4% but the pollutant emissions are increased by 5%. If the pollutant emissions are controlled, the sales authorization of diesel passenger cars would be a good countermeasure against the climatic change convention.

  18. Development and review of Euro 5 passenger car emission factors based on experimental results over various driving cycles

    OpenAIRE

    Fontaras, Georgios; Franco, Vicente; Dilara, Panagiota; Martini, Giorgio; Manfredi, Urbano

    2014-01-01

    The mass emissions of CO2 and regulated pollutants (NOX, HC, CO, PM) of thirteen Euro 5 compliant passenger cars (seven gasoline, six Diesel) were measured on a chassis dynamometer. The vehicles were driven repeatedly over the European type-approval driving cycle (NEDC) and the more dynamic WMTC and CADC driving cycles. Distance-specific emission factors were derived for each pollutant and sub-cycle which were subsequently compared to the corresponding emission factors provided by the referen...

  19. Noise in the passenger cars of high-speed trains.

    Science.gov (United States)

    Hong, Joo Young; Cha, Yongwon; Jeon, Jin Yong

    2015-12-01

    The aim of this study is to investigate the effects of both room acoustic conditions and spectral characteristics of noises on acoustic discomfort in a high-speed train's passenger car. Measurement of interior noises in a high-speed train was performed when the train was operating at speeds of 100 km/h and 300 km/h. Acoustic discomfort caused by interior noises was evaluated by paired comparison methods based on the variation of reverberation time (RT) in a passenger car and the spectral differences in interior noises. The effect of RT on acoustic discomfort was not significant, whereas acoustic discomfort significantly varied depending on spectral differences in noise. Acoustic discomfort increased with increment of the sound pressure level (SPL) ratio at high frequencies, and variation in high-frequency noise components were described using sharpness. Just noticeable differences of SPL with low- and high-frequency components were determined to be 3.7 and 2.9 dB, respectively. This indicates that subjects were more sensitive to differences in SPLs at the high-frequency range than differences at the low-frequency range. These results support that, for interior noises, reduction in SPLs at high frequencies would significantly contribute to improved acoustic quality in passenger cars of high-speed trains.

  20. The importance of high vehicle power for passenger car emissions

    Science.gov (United States)

    Carslaw, David C.; Williams, Martin L.; Tate, James E.; Beevers, Sean D.

    2013-04-01

    In this paper we use a quantile regression technique to explore the emissions characteristics of petrol and diesel passenger cars to reveal the importance of high vehicle power on exhaust emissions. A large database of ≈67,000 passenger cars from vehicle emission remote sensing data was used from surveys from several campaigns around the UK. Most previous remote sensing studies have focused on presenting mean emission estimates by vehicle type over time. However, as shown in the current work, considerably more insight can be gained into vehicle emission characteristics if techniques are used that can describe and model the full distribution of vehicle emissions as a function of important explanatory variables. For post-2000 model year (Euro 3-5) diesel cars it is shown that there is a strong dependence of vehicle specific power for emissions of NOx that was absent in earlier models and is absent for other pollutants such as CO, hydrocarbons and 'smoke'. Furthermore, we also find a stronger dependence on vehicle specific power for older catalyst-equipped petrol vehicles (Euro 1/2) on emissions of NOx that is less important for other emissions such as CO and hydrocarbons. Moreover, it is shown that while the rated maximum power output of petrol cars has remained almost constant over the past 15-20 years, the power output from diesel cars has increased markedly by about 50%. These results suggest that changes to vehicle technology, driving conditions and driver behaviour have become more important determinants of passenger car NOx emissions in recent years and may help explain why urban ambient concentrations of NOx have not decreased as much as anticipated.

  1. Influence of unsteady aerodynamics on driving dynamics of passenger cars

    Science.gov (United States)

    Huemer, Jakob; Stickel, Thomas; Sagan, Erich; Schwarz, Martin; Wall, Wolfgang A.

    2014-11-01

    Recent approaches towards numerical investigations with computational fluid dynamics methods on unsteady aerodynamic loads of passenger cars identified major differences compared with steady-state aerodynamic excitations. Furthermore, innovative vehicle concepts such as electric-vehicles or hybrid drives further challenge the basic layout of passenger cars. Therefore, the relevance of unsteady aerodynamic loads on cross-wind stability of changing basic vehicle architectures should be analysed. In order to assure and improve handling and ride characteristics at high velocity of the actual range of vehicle layouts, the influence of unsteady excitations on the vehicle response was investigated. For this purpose, a simulation of the vehicle dynamics through multi-body simulation was used. The impact of certain unsteady aerodynamic load characteristics on the vehicle response was quantified and key factors were identified. Through a series of driving simulator tests, the identified differences in the vehicle response were evaluated regarding their significance on the subjective driver perception of cross-wind stability. Relevant criteria for the subjective driver assessment of the vehicle response were identified. As a consequence, a design method for the basic layout of passenger cars and chassis towards unsteady aerodynamic excitations was defined.

  2. Improvement of the directional stability of passenger car trailer couplings with actively controlled steering

    Science.gov (United States)

    Desens, Jens

    The stabilization of pendulum oscillations of passenger car trailer couplings, using active steering, was examined. A linear model of the couplings was presented. Each axle was provided with a controller. The controllers were optimized, with regard to necessary sensors, in order to minimize costs. The rear and the front axles were provided with a control unit in order to compute the potential prevailing in the active steering of several axles. It was shown that the passenger car rear axle was the most suitable for coupling stabilization. The experiment was simulated, using a complex coupling model. The developed controller allowed the passenger car trailer to be driven at a speed higher than 150 km per hour.

  3. [The peculiar features of conducting comprehensive expertises of the injuries inflicted inside the passenger car compartment].

    Science.gov (United States)

    Fetisov, V A; Gusarov, A A; Smirenin, S A

    2016-01-01

    The present article deals with the problem of forensic medical diagnostics of the injuries inflicted inside the passenger car compartment during motor vehicle accidents. The authors place special emphasis on the fact of a significant increase in the number of road traffic accidents (RTA) with such consequences throughout the world. The modern automobile industry pays much attention to the enhancement of the car safety features by significantly improving the design of passenger compartments. It accounts for a change in the traditional character of the injuries to both the driver and the passengers resulting from motor vehicle accidents. This, in turn, creates difficulties for the forensic medical experts as regards personality identification of the subjects who happened to be inside the car at the moment of the collision especially in the case of unascertainable circumstances of the accident and/or the involvement of several victims. The authors describe peculiarities of the injuries inflicted inside the passenger car compartment during road traffic accidents including such that result from bringing the driver and the passengers closer to the construction elements of the car (stage I), their direct contact with these elements (stage II), and subsequent displacement (stage III).

  4. The contribution to the greenhouse effect by passenger cars and heating is increasing

    International Nuclear Information System (INIS)

    Bouchereau, J.M.

    2000-12-01

    Between 1990 and 1998, the domestic sector contribution to the greenhouse effect increased from 25 % to 27 %. During this period, there was a 20 % rise in greenhouse gas emissions from passenger cars. These emissions amounted to 20 million tonnes of carbon equivalent out of a total of 175 million tonnes in 1998 (all sectors taken together). Carbon dioxide emissions from the tertiary sector increased by 2,3 % annually between 1980 and 1998, particularly as a result of increased road freight transport. Although technological progress has been made on fuel consumption of vehicles, greater use of passenger cars combined with decreasing running costs has led to gross emissions in France being 2 % more in 1998 than in 1990. In 1998, the transport sector (passenger cars and freight transport) was responsible for three-quarters of this increase. (author)

  5. Energy saving and CO2 mitigation through restructuring Jordan's transportation sector: The diesel passenger cars scenario

    International Nuclear Information System (INIS)

    Al-Hinti, I.; Al-Ghandoor, A.; Akash, B.; Abu-Nada, E.

    2007-01-01

    The transportation sector is responsible for 37% of the total final energy consumption in Jordan, with passenger cars taking a share of 57% in this sector. Improvement of the energy efficiency of the transportation sector can help in alleviating socio-economic pressures resulting from the inflating fuel bill and in lowering the relatively high CO 2 emission intensity. Current legislations mandate that all passenger cars operating in Jordan are to be powered with spark ignition engines using gasoline fuel. This paper examines potential benefits that can be achieved through the introduction of diesel cars to the passenger cars market in Jordan. Three scenarios are suggested for implementation and investigated with a forecasting model on the basis of local and global trends over the period 2007-2027. It is demonstrated that introducing diesel passenger cars can slow down the growth of energy consumption in the transportation sector resulting in significant savings in the national fuel bill. It is also shown that this is an effective and feasible option for cutting down CO 2 emissions

  6. Short-term exposure to PM 10, PM 2.5, ultrafine particles and CO 2 for passengers at an intercity bus terminal

    Science.gov (United States)

    Cheng, Yu-Hsiang; Chang, Hsiao-Peng; Hsieh, Cheng-Ju

    2011-04-01

    The Taipei Bus Station is the main transportation hub for over 50 bus routes to eastern, central, and southern Taiwan. Daily traffic volume at this station is about 2500 vehicles, serving over 45,000 passengers daily. The station is a massive 24-story building housing a bus terminal, a business hotel, a shopping mall, several cinemas, offices, private residential suites, and over 900 parking spaces. However, air quality inside this bus terminal is a concern as over 2500 buses are scheduled to run daily. This study investigates the PM 10, PM 2.5, UFP and CO 2 levels inside and outside the bus terminal. All measurements were taken between February and April 2010. Measurement results show that coarse PM inside the bus terminal was resuspended by the movement of large numbers of passengers. The fine and ultrafine PM in the station concourse were from outside vehicles. Moreover, fine and ultrafine PM at waiting areas were exhausted directly from buses in the building. The CO 2 levels at waiting areas were likely elevated by bus exhaust and passengers exhaling. The PM 10, PM 2.5 and CO 2 levels at the bus terminal were lower than Taiwan's EPA suggested standards for indoor air quality. However, UFP levels at the bus terminal were significantly higher than those in the urban background by about 10 times. Therefore, the effects of UFPs on the health of passengers and workers must be addressed at this bus terminal since the levels of UFPs are higher than >1.0 × 10 5 particles cm -3.

  7. Improving car passengers' comfort and experience by supporting the use of handheld devices

    NARCIS (Netherlands)

    Veen, S.A.T. van; Hiemstra-van Mastrigt, S.; Kamp, I.; Vink, P.

    2014-01-01

    Background: There is a demand for interiors to support other activities in a car than controlling the vehicle. Currently, this is the case for the car passengers and-in the future-autonomous driving cars will also facilitate drivers to perform other activities. One of these activities is working

  8. MATHEMATICAL MODELING OF UNSTEADY HEAT EXCHANGE IN A PASSENGER CAR

    Directory of Open Access Journals (Sweden)

    I. Yu. Khomenko

    2013-07-01

    Full Text Available Purpose.Existing mathematicalmodelsofunsteadyheatexchangeinapassengercardonotsatisfytheneedofthedifferentconstructivedecisionsofthelifesupportsystemefficiencyestimation. They also don’t allow comparing new and old life support system constructions influence on the inner environment conditions. Moreoverquite frequently unsteady heat exchange processes were studied at the initial car motion stage. Due to the new competitive engineering decisionsof the lifesupportsystemthe need of a new mathematical instrument that would satisfy the mentioned features and their influence on the unsteadyheatexchangeprocesses during the whole time of the road appeared. The purpose of this work is creation of the mathematicalmodel ofunsteadyheatexchangeinapassengercarthatcan satisfythe above-listed requirements. Methodology. Fortheassigned task realizationsystemofdifferentialequationsthatcharacterizesunsteadyheatexchangeprocessesinapassengercarwascomposed; forthesystemof equationssolution elementary balance method was used. Findings. Computational algorithm was developed andcomputer program for modeling transitional heat processes in the car was designed. It allows comparing different life support system constructions influence on the inner environment conditionsand unsteady heat exchange processes can be studied at every car motion stage. Originality.Mathematicalmodelofunsteadyheatexchangeinapassengercarwasimproved. That is why it can be used for the heat engineering studying of the inner car state under various conditions and for the operation of the different life support systems of passenger cars comparison. Mathematicalmodelingofunsteadyheatexchangeinapassengercarwas made by the elementary balance method. Practical value. Created mathematical model gives the possibility to simulate temperature changes in passenger car on unsteady thermal conditions with enough accuracy and to introduce and remove additional elements to the designed model. Thus different

  9. Improving car passengers' comfort and experience by supporting the use of handheld devices

    NARCIS (Netherlands)

    Van Veen, S.A.T.; Van Mastrigt, S.; Kamp, I.; Vink, P.

    2014-01-01

    BACKGROUND: There is a demand for interiors to support other activities in a car than controlling the vehicle. Currently, this is the case for the car passengers and – in the future – autonomous driving cars will also facilitate drivers to perform other activities. One of these activities is working

  10. The effect on road load due to variations in valid coast down tests for passenger cars

    NARCIS (Netherlands)

    Mensch, P. van; Ligterink, N.E.; Cuelenaere, R.F.A.

    2014-01-01

    Real-world CO2 emissions of passenger cars very often deviate from the Type Approval value. The Type Approval value for CO2 emissions of passenger cars is based on a chassis dynamometer test in a laboratory. The total vehicle resistance of a vehicle, or 'road load', is simulated on the chassis

  11. Competitive Position of Dependent Passenger Car Maintenance Companies – Influences, Developments and Challenges in the German Market

    Directory of Open Access Journals (Sweden)

    Werdich Karl

    2015-06-01

    Full Text Available The presented paper concerns itself with passenger car maintenance companies and their competitiveness. Internal and external influences, change drivers and general changes in the companies and their organisation were identified and analysed. The influence of the development of technology and the diffusion of innovations are highlighted in particular. Under consideration of the competitiveness factors, current and future challenges for the passenger car maintenance companies were worked out. Based on these analyses, future tasks, problem statements and challenges were compiled for passenger car maintenance companies from which other subjects of scientific investigation in area of strategic and economic importance arose.

  12. Statistical Evaluation of the Emissions Level Of CO, CO2 and HC Generated by Passenger Cars

    Directory of Open Access Journals (Sweden)

    Claudiu Ursu

    2014-12-01

    Full Text Available This paper aims to make an evaluation of differences emission level of CO, CO2 and HC generated by passenger cars in different walking regimes and times, to identify measures of reducing pollution. Was analyzed a sample of Dacia Logan passenger cars (n = 515, made during the period 2004-2007, equipped with spark ignition engines, assigned to emission standards EURO 3 (E3 and EURO4 (E4. These cars were evaluated at periodical technical inspection (ITP by two times in the two walk regimes (slow idle and accelerated idle. Using the t test for paired samples (Paired Samples T Test, the results showed that there are significant differences between emissions levels (CO, CO2, HC generated by Dacia Logan passenger cars at both assessments, and regression analysis showed that these differences are not significantly influenced by turnover differences.

  13. THE STUDY OF BRAKE SYSTEMS OF PASSENGER CARS MODEL 61-779 AND THEIR MODIFICATIONS PRODUCED BY OPEN JOINT STOCK COMPANY KRJUKIV CAR BUILDING PLANT

    Directory of Open Access Journals (Sweden)

    Yu. Ya. Vodiannikov

    2007-11-01

    Full Text Available The results of research of brake system for the model 61-779 of a passenger car manufactured by JSC «KVBZ» for the period from 2001 to 2006 are presented. It is shown that at the existing gear ratio of a brake lever transmission the passenger car brake efficiency does not correspond to running speed of 140 km/h. The causes of the wheel pairs damage occurrence in exploitation of a passenger train «Kiev – Moscow» as well as the recommendations on their elimination and brake system perfection are considered.

  14. Influence of driving style on fuel consumption and Emissions in diesel-powered passenger car

    OpenAIRE

    Fonseca González, Natalia Elizabeth; Casanova Kindelán, Jesús; Espinosa Zapata, Felipe

    2010-01-01

    This paper presents the main results of a study on the influence of driving style on fuel consumption and pollutant emissions of diesel passenger car in urban traffic. Driving styles (eco, normal or aggressive) patterns were based on the “eco-driving” criteria. The methodology is based on on-board emission measurements in real urban traffic in the city of Madrid. Five diesel passenger cars, have been tested. Through a statistical analysis, a Dynamic Performance Index was defined for die...

  15. Passenger train emergency systems : development of prototype railEXODUS software for U.S. passenger rail car egress.

    Science.gov (United States)

    2014-11-01

    The Federal Railroad Administration (FRA), U.S. Department of Transportation (U.S. DOT), is sponsoring a research program, which includes investigation of the applicability of time-based egress performance requirements to U.S. passenger rail cars. Th...

  16. Factor Analysis of Passenger Cars Using as a Taxi

    Directory of Open Access Journals (Sweden)

    Deriugin O.V.

    2016-05-01

    Full Text Available A procedure to select passenger cars has been proposed. The procedure helps substantiate choice of effective transportation means in accordance with taxi class to meet consumption requirements of those taking part in transportation process from the viewpoint of comfort, safety, and minimum expenditures in the context of such transportation type.

  17. Development Of Fiber Optics For Passenger Car Applications

    Science.gov (United States)

    Steele, R. E.; Schmitt, H. J.

    1987-12-01

    The benefits of fiber optics for telecommunications and Local Area Networks (LANs) are well documented. The benefits to passenger car applications are not as clearly defined. This paper examines the differences between Telecommunications, LAN, and automotive point to point and network applications. Current production automotive applications of optics and fiber optics, automotive data communications trends, and both functional and non-functional requirements and constraints will be described.

  18. Fiscal policy and CO2 emissions of new passenger cars in the EU

    NARCIS (Netherlands)

    Gerlagh, Reyer; Van Den Bijgaart, Inge; Nijland, Hans; Michielsen, Thomas

    To what extent have national fiscal policies contributed to the decarbonisation of newly sold passenger cars? We construct a simple model that generates predictions regarding the effect of fiscal policies on average CO2 emissions of new cars, and then test the model empirically. Our empirical

  19. EVs and post 2020 CO2 targets for passenger cars

    NARCIS (Netherlands)

    Smokers, R.T.M.; Verbeek, M.; Zyl, S. van

    2013-01-01

    This paper analyses what post 2020 targets may be necessary for the European CO2 legislation for passenger cars in order to reach the overall sectoral goal of 60% reduction of transport's greenhouse gas emissions by 2050 relative to 1990, as defined in the European Commission's White Paper. The

  20. Delay-based Passenger Car Equivalent at Signalized Intersections in Iran

    Directory of Open Access Journals (Sweden)

    Habibollah Nassiri

    2017-04-01

    Full Text Available Due to their different sizes and operational characteristics, vehicles other than passenger cars have a different influence on traffic operations especially at intersections. The passenger car equivalent (PCE is the parameter that shows how many passenger cars must be substituted for a specific heavy vehicle to represent its influence on traffic operation. PCE is commonly estimated using headway-based methods that consider the excess headway utilized by heavy vehicles. In this research, the PCE was estimated based on the delay parameter at three signalized intersections in Tehran, Iran. The data collected were traffic volume, travel time for each movement, signalization, and geometric design information. These data were analysed and three different models, one for each intersection, were constructed and calibrated using TRAF-NETSIM simulation software for unsaturated traffic conditions. PCE was estimated under different scenarios and the number of approach movements at each intersection. The results showed that for approaches with only one movement, PCE varies from 1.1 to 1.65. Similarly, for approaches with two and three movements, the PCE varies from 1.07 to 1.99 and from 0.76 to 3.6, respectively. In addition, a general model was developed for predicting PCE for intersections with all of the movements considered. The results obtained from this model showed that the average PCE of 1.5 is similar to the value recommended by the HCM (Highway Capacity Manual 1985. However, the predicted PCE value of 1.9 for saturated threshold is closer to the PCE value of 2 which was recommended by the HCM 2000 and HCM 2010.

  1. The risk of airborne influenza transmission in passenger cars.

    Science.gov (United States)

    Knibbs, L D; Morawska, L; Bell, S C

    2012-03-01

    Travel in passenger cars is a ubiquitous aspect of the daily activities of many people. During the 2009 influenza A(H1N1) pandemic a case of probable transmission during car travel was reported in Australia, to which spread via the airborne route may have contributed. However, there are no data to indicate the likely risks of such events, and how they may vary and be mitigated. To address this knowledge gap, we estimated the risk of airborne influenza transmission in two cars (1989 model and 2005 model) by employing ventilation measurements and a variation of the Wells-Riley model. Results suggested that infection risk can be reduced by not recirculating air; however, estimated risk ranged from 59% to 99·9% for a 90-min trip when air was recirculated in the newer vehicle. These results have implications for interrupting in-car transmission of other illnesses spread by the airborne route.

  2. In-use vs. type-approval fuel consumption of current passenger cars in Europe

    International Nuclear Information System (INIS)

    Ntziachristos, L.; Mellios, G.; Tsokolis, D.; Keller, M.; Hausberger, S.; Ligterink, N.E.; Dilara, P.

    2014-01-01

    In-use fuel consumption data of 924 passenger cars (611 petrol, 313 diesel) were collected from various European sources and were evaluated in comparison to their corresponding type-approval values. The analysis indicated that the average in-use fuel consumption was higher than the type-approval one by 11% for petrol cars and 16% for diesel cars. Comparison of this dataset with the Travelcard database in the Netherlands showed that the deviation increased for late model years and in particular for cars with low type-approval values. The deviation was higher than 60% for vehicles registered in 2012 within the 90–100 gCO 2 /km bin. Unrealistic vehicle resistances used in type-approval were identified as one of the prime reasons of the difference. A simplified linear model developed in the study may be used to predict in-use fuel consumption based on data publicly available. The model utilizes the fuel consumption measured in type-approval, the mass, and the engine capacity to provide in-use fuel consumption. This may be either used to correct fuel consumption factors currently utilized by emission models (e.g. COPERT, HBEFA, VERSIT+, and others) or could be used independently to make projections on how fuel consumption may develop on the basis of changing future passenger cars characteristics. - Highlights: • In-use fuel consumption of petrol and diesel passenger cars is 11% and 16% higher than type-approval, respectively. • The relative difference between in-use and type-approval increases for late model and vehicles with low consumption. • Unrealistically low vehicle resistances are identified as a prime reason of low type-approval fuel consumption. • A model developed predicts in-use consumption on the basis of type-approval consumption, vehicle mass, and engine capacity

  3. Minute ventilation of cyclists, car and bus passengers: an experimental study.

    NARCIS (Netherlands)

    Zuurbier, M.; Hoek, G.; van den Hazel, P.J.; Brunekreef, B.

    2009-01-01

    ABSTRACT: BACKGROUND: Differences in minute ventilation between cyclists, pedestrians and other commuters influence inhaled doses of air pollution. This study estimates minute ventilation of cyclists, car and bus passengers, as part of a study on health effects of commuters' exposure to air

  4. Alcohol Fuel in Passenger Car

    Directory of Open Access Journals (Sweden)

    Adam Polcar

    2016-01-01

    Full Text Available The present article studies the effects of combustion of high-percentage mixture of bioethanol and gasoline on the output parameters of a passenger car engine. The car engine has not been structurally modified for the combustion of fuels with higher ethanol content. The mixture used consisted of E85 summer blend and Natural 95 gasoline in a ratio of 50:50. The parameters monitored during the experiment included the air-fuel ratio in exhaust gasses, the power output and torque of the engine and also the specific energy consumption and efficiency of the engine. As is apparent from the results, E85+N95 (50:50 mixture combustion results in lean-burn (λ > 1 due to the presence of oxygen in bioethanol. The lean-burn led to a slight decrease in torque and power output of the engine. However, due to the positive physicochemical properties of bioethanol, the decrease has not been as significant as would normally be expected from the measured air-fuel ratio. These findings are further confirmed by the calculated energy required to produce 1 kWh of energy, and by the higher efficiency of the engine during the combustion of a 50% bioethanol mixture.

  5. Estimates the Emission of Passenger Cars Based on the First Developed Driving Cycle in Nakhon Ratchasima Municipality, Thailand

    Directory of Open Access Journals (Sweden)

    Muangnak Noppatsorn

    2017-01-01

    Full Text Available This study aims to estimate emissions of passenger cars traveled on the highways in Nakhon Ratchasima Municipality (NRM based on recently developed driving cycles. A mobile phone application (SafeMate was used to record speed-time of passenger car on the highways both weekday and weekend. The results showed that the driving cycles of the passenger cars on highway 224 and 304 were quite different. More traffic congestion on highway 224 impacted the average speeds, ranging from 10 to 34 km/h with longer idling time. The average speeds on highway 304 ranged from 49 to 69 km/h with more cruise time. The combined driving cycles on both highways showed the average speeds of 20-40 km/h depending upon the time of days. The traffic density on weekday was higher than the weekend. Peak-hour weekday showed lower traffic flow than off-peak hour which was the opposite of the weekend. Based on the derived driving cycles, the passenger car traveled on the highways in NRM emitted CO, NOx and HC approximately 90.7-129.8, 25.5-34.5 and 6.9-11.7 tons/year, respectively. The passenger cars were estimated to emit about 13,927.7-20,419.3 tons/year of carbon dioxide on the highways. The highway 2 accounted more of the emissions due to the traffic volume and coverage distance in NRM.

  6. Electricity versus hydrogen for passenger cars under stringent climate change control

    NARCIS (Netherlands)

    Rösler, H.; van der Zwaan, B.; Keppo, I.; Bruggink, J.

    2014-01-01

    In this article we analyze how passenger car transportation in Europe may change this century under permanent high oil prices and stringent climate control policy. We focus on electricity and hydrogen as principal candidate energy carriers, because these two options are increasingly believed to

  7. Small passenger car transmission test; Chevrolet LUV transmission

    Science.gov (United States)

    Bujold, M. P.

    1980-01-01

    A 1978 Chevrolet LUV manual transmission tested per the applicable portions of a passenger car automatic transmission test code (SAE J65lb) which required drive performance, coast performance, and no load test conditions. Under these test conditions, the transmission attained maximum efficiencies in the upper ninety percent range for both drive performance tests and coast performance tests. The major results of this test (torque, speed, and efficiency curves) are presented. Graphs map the complete performance characteristics for the Chevrolet LUV transmission.

  8. INVESTIGATION OF ANTILOCK BRAKE SYSTEM EFFECT ON PASSENGER CAR BRAFKING EFFICIENCY

    Directory of Open Access Journals (Sweden)

    I. Davidenko

    2011-01-01

    Full Text Available It has been experimentally proved that in case of emergency braking the constant decelera-tion of passenger cars equipped by antilock brake system exceeds the tabulated statistical data by 7,7–17 % that is recommended to apply at technical expertise at traffic accident causes investigation.

  9. Post-consumer tires back into new tires: de-vulcanization and re-utilization of passenger car tires

    OpenAIRE

    Saiwari, Sitisaiyidah

    2013-01-01

    Enabling recycling loops for used passenger car tires is a challenge and an opportunity. The challenge lies in the presence of SBR as the main elastomer in this type of tires, which makes this material difficult to reclaim due to the tendency of the elastomer chain fragments to re-combine. The opportunity lies in the wide availability of the material and in the fact that passenger car tires form a huge potential market for recycled rubber. The aim of this study is to develop a de-vulcanizatio...

  10. Human Thermal Comfort and Heat Removal Efficiency for Ventilation Variants in Passenger Cars

    Directory of Open Access Journals (Sweden)

    Saboora Khatoon

    2017-10-01

    Full Text Available The realization of a comfortable thermal environment with low energy consumption and improved ventilation in a car has become the aim of manufacturers in recent decades. Novel ventilation concepts with more flexible cabin usage and layouts are appealing owing to their potential for improving passenger comfort and driving power. In this study, three variant ventilation concepts are investigated and their performance is compared with respect to energy efficiency and human comfort of the driver and passenger in front and a child in the rear compartment. FLUENT 16.0, a commercial three-dimensional (3D software, are used for the simulation. A surface-to-surface radiation model is applied under transient conditions for a car parked in summer conditions with its engine in the running condition. The results for the standard Fanger’s model and modified Fanger’s model are analyzed, discussed, and compared for the driver, passenger, and child. The modified Fanger’s model determines the thermal sensation on the basis of mean arterial pressure.

  11. Evaluation of the feasibility of using fuel cells in passenger cars

    Energy Technology Data Exchange (ETDEWEB)

    Selwood, P G

    2001-07-01

    This project was conceived to evaluate the commercial prospects for fuel cell powered passenger cars in the UK and Western Europe, over the time-frame to 2010. First of all the existing market place was examined and reasons for buying particular vehicles and or size of vehicle was established. The conclusion was that there was a market potential of 32,250 pa in UK (244,000 pa Western Europe) of a 'C' Sector sized car using a fuel cell engine provided it sold at no more that 1000 pounds sterling above the conventional price. (author)

  12. THE RATIONALE FOR EXTENDING THE SERVICES OF PASSENGER CARS WITH POCKETS OF CORROSION IN THE CENTER SILL

    Directory of Open Access Journals (Sweden)

    S. V. Myamlin

    2015-09-01

    Full Text Available Purpose. The scientific work supposed: 1 the search of accounting ways of the local corrosion damages influence to the car design, that were expired the appointed time, for the purpose of renewal; 2 experimental verification of conformity of material construction requirements of the normative documentation and justification for extending the services of passenger cars with pockets of corrosion after 30 years of operation; 3 the conformity assessment of residual life of the structure of car bodies operating pressures in the next 5 years of use. Methodology. The developed algorithm of technical diagnostics of cars with pockets of corrosion of the center sill contains several stages. First, a survey of technical condition of structures is conducted by a visual-optical method and nondestructive control methods, and the degree of damage is determined. In the next phase the experimental verification of conformity of the structure and mechanical properties of the center sill of the car with the pockets of corrosion to regulatory requirements are executed. Next, the study of strength of the supporting structures of car bodies on the basis of experimental static and impact tests of strength is executed. Finally, the endurance tests are conducted on the effect of the longitudinal forces and the evaluation and prediction of compliance resource car bodies for the next period are executed. Findings. The actual work is completed by obtaining the experimental data on the feasibility of extending the service life of passenger cars as from the point of view of an operating time of load-bearing elements of the car body to the resource, and from the point of view of chemical composition, structure and mechanical properties of the center sill with pockets of corrosion. The presence of local corrosion damages of the center sill of the presented size is not a threat to the structural strength and safety. Originality. The authors conducted a comprehensive study to

  13. The influence of passenger car front shape on pedestrian injury risk observed from German in-depth accident data.

    Science.gov (United States)

    Li, Guibing; Lyons, Mathew; Wang, Bingyu; Yang, Jikuang; Otte, Dietmar; Simms, Ciaran

    2017-04-01

    Quantified relationships between passenger car front shape and pedestrian injury risk derived from accident data are sparse, especially considering the significant recent changes in car front design. The purpose of this paper is therefore to investigate the detailed effects of passenger car front shape on injury risk to a pedestrian's head, thorax, pelvis and leg in the event of a vehicle pedestrian impact. Firstly, an accident sample of 594 pedestrian cases captured during 2000-2015 from the German In-Depth Accident Study (GIDAS) database was employed. Multicollinearity diagnostic statistics were then used to detect multicollinearity between the predictors. Following this, logistic regression was applied to quantify the effects of passenger car front shape on injury risks while controlling for impact speed and pedestrian age. Results indicate that the bumper lower depth (BLD), bumper lower height (BLH), bumper upper height (BUH) and normalised bumper lower/upper height (NBLH/NBUH) are statistically significant for AIS2+ leg injury risk. The normalised bonnet leading edge height (NBLEH) has a statistically significant influence on AIS2+ femur/pelvis injury occurrence. The passenger car front shape did not show statistical significance for AIS3+ thorax and head injuries. The impact speed and pedestrian age are generally significant factors influencing AIS2+ leg and pelvis injuries, and AIS3+ thorax and head injuries. However, when head impacts are fixed on the central windscreen region both pedestrian age and impact speed are not statistically significant for AIS3+ head injury. For quantified effects, when controlling for speed, age and BUH, an average 7% and 6% increase in AIS2+ leg injury odds was observed for every 1cm increase in BLD and BLH respectively; 1cm increase in BUH results in a 7% decrease in AIS2+ leg injury odds when the BLD or BLH are fixed respectively (again controlling for impact speed and pedestrian age); the average AIS2+ femur/pelvis injury

  14. Speech privacy and annoyance considerations in the acoustic environment of passenger cars of high-speed trains.

    Science.gov (United States)

    Jeon, Jin Yong; Hong, Joo Young; Jang, Hyung Suk; Kim, Jae Hyeon

    2015-12-01

    It is necessary to consider not only annoyance of interior noises but also speech privacy to achieve acoustic comfort in a passenger car of a high-speed train because speech from other passengers can be annoying. This study aimed to explore an optimal acoustic environment to satisfy speech privacy and reduce annoyance in a passenger car. Two experiments were conducted using speech sources and compartment noise of a high speed train with varying speech-to-noise ratios (SNRA) and background noise levels (BNL). Speech intelligibility was tested in experiment I, and in experiment II, perceived speech privacy, annoyance, and acoustic comfort of combined sounds with speech and background noise were assessed. The results show that speech privacy and annoyance were significantly influenced by the SNRA. In particular, the acoustic comfort was evaluated as acceptable when the SNRA was less than -6 dB for both speech privacy and noise annoyance. In addition, annoyance increased significantly as the BNL exceeded 63 dBA, whereas the effect of the background-noise level on the speech privacy was not significant. These findings suggest that an optimal level of interior noise in a passenger car might exist between 59 and 63 dBA, taking normal speech levels into account.

  15. Cooling performance and evaluation of automotive refrigeration system for a passenger car

    Science.gov (United States)

    Prajitno, Deendarlianto, Majid, Akmal Irfan; Mardani, Mahardeka Dhias; Wicaksono, Wendi; Kamal, Samsul; Purwanto, Teguh Pudji; Fauzun

    2016-06-01

    A new design of automotive refrigeration system for a passenger car was proposed. To ensure less energy consumption and optimal thermal comfort, the performance of the system were evaluated. This current research was aimed to evaluate the refrigeration characteristics of the system for several types of cooling load. In this present study, a four-passenger wagon car with 1500 cc gasoline engine that equipped by a belt driven compressor (BDC) was used as the tested vehicle. To represent the tropical condition, a set of lamps and wind sources are installed around the vehicle. The blower capacity inside a car is varied from 0.015 m/s to 0.027 m/s and the compressor speed is varied at variable 820, 1400, and 2100 rpm at a set temperature of 22°C. A set of thermocouples that combined by data logger were used to measure the temperature distribution. The system uses R-134a as the refrigerant. In order to determine the cooling capacity of the vehicle, two conditions were presented: without passengers and full load conditions. As the results, cooling capacity from any possible heating sources and transient characteristics of temperature in both systems for the cabin, engine, compressor, and condenser are presented in this work. As the load increases, the outlet temperature of evaporator also increases due to the increase of condensed air. This phenomenon also causes the increase of compressor work and compression ratio which associated to the addition of specific volume in compressor inlet.

  16. Development and review of Euro 5 passenger car emission factors based on experimental results over various driving cycles.

    Science.gov (United States)

    Fontaras, Georgios; Franco, Vicente; Dilara, Panagiota; Martini, Giorgio; Manfredi, Urbano

    2014-01-15

    The emissions of CO2 and regulated pollutants (NOx, HC, CO, PM) of thirteen Euro 5 compliant passenger cars (seven gasoline, six Diesel) were measured on a chassis dynamometer. The vehicles were driven repeatedly over the European type-approval driving cycle (NEDC) and the more dynamic WMTC and CADC driving cycles. Distance-specific emission factors were derived for each pollutant and sub-cycle, and these were subsequently compared to the corresponding emission factors provided by the reference European models used for vehicle emission inventory compilation (COPERT and HBEFA) and put in context with the applicable European emission limits. The measured emissions stayed below the legal emission limits when the type-approval cycle (NEDC) was used. Over the more dynamic cycles (considered more representative of real-world driving) the emissions were consistently higher but in most cases remained below the type-approval limit. The high NOx emissions of Diesel vehicles under real-world driving conditions remain the main cause for environmental concern regarding the emission profile of Euro 5 passenger cars. Measured emissions of NOx exceeded the type-approval limits (up to 5 times in extreme cases) and presented significantly increased average values (0.35 g/km for urban driving and 0.56 g/km for motorway driving). The comparison with the reference models showed good correlation in all cases, a positive finding considering the importance of these tools in emission monitoring and policy-making processes. © 2013. Published by Elsevier B.V. All rights reserved.

  17. MATHEMATICAL MODEL OF UNSTEADY HEAT TRANSFER OF PASSENGER CAR WITH HEATING SYSTEM

    OpenAIRE

    E. V. Biloshytskyi

    2018-01-01

    Purpose. The existing mathematical models of unsteady heat processes in a passenger car do not fully reflect the thermal processes, occurring in the car wits a heating system. In addition, unsteady heat processes are often studied in steady regime, when the heat fluxes and the parameters of the thermal circuit are constant and do not depend on time. In connection with the emergence of more effective technical solutions to the life support system there is a need for creating a new mathematical...

  18. Speed-dependent emission of air pollutants from gasoline-powered passenger cars.

    Science.gov (United States)

    Jung, Sungwoon; Lee, Meehye; Kim, Jongchoon; Lyu, Youngsook; Park, Junhong

    2011-01-01

    In Korea emissions from motor vehicles are a major source of air pollution in metropolitan cities, and in Seoul a large proportion of the vehicle fleet is made up of gasoline-powered passenger cars. The carbon monoxide (CO), hydrocarbons (HC), oxides of nitrogen (NOx) and carbon dioxide (CO2) contained in the exhaust emissions from 76 gasoline-powered passenger cars equipped with three-way catalysts has been assessed by vehicle speed, vehicle mileage and model year. The results show that CO, HC, NOx and CO2 emissions remained almost unchanged at higher speeds but decreased rapidly at lower speeds. While a reduction in CO, HC and NOx emissions was noticeable in vehicles of recent manufacture and lower mileage, CO2 emissions were found to be insensitive to vehicle mileage, but strongly dependent on gross vehicle weight. Lower emissions from more recent gasoline-powered vehicles arose mainly from improvements in three-way catalytic converter technology following strengthened emission regulations. The correlation between CO2 emission and fuel consumption has been investigated with a view to establishing national CO2 emission standards for Korea.

  19. Global carbon benefits of material substitution in passenger cars until 2050 and the impact on the steel and aluminum industries.

    Science.gov (United States)

    Modaresi, Roja; Pauliuk, Stefan; Løvik, Amund N; Müller, Daniel B

    2014-09-16

    Light-weighting of passenger cars using high-strength steel or aluminum is a common emissions mitigation strategy. We provide a first estimate of the global impact of light-weighting by material substitution on GHG emissions from passenger cars and the steel and aluminum industries until 2050. We develop a dynamic stock model of the global car fleet and combine it with a dynamic MFA of the associated steel, aluminum, and energy supply industries. We propose four scenarios for substitution of conventional steel with high-strength steel and aluminum at different rates over the period 2010-2050. We show that light-weighting of passenger cars can become a "gigaton solution": Between 2010 and 2050, persistent light-weighting of passenger cars can, under optimal conditions, lead to cumulative GHG emissions savings of 9-18 gigatons CO2-eq compared to development business-as-usual. Annual savings can be up to 1 gigaton per year. After 2030, enhanced material recycling can lead to further reductions: closed-loop metal recycling in the automotive sector may reduce cumulative emissions by another 4-6 gigatons CO2-eq. The effectiveness of emissions mitigation by material substitution significantly depends on how the recycling system evolves. At present, policies focusing on tailpipe emissions and life cycle assessments of individual cars do not consider this important effect.

  20. Design and construction aspects of a zero inertia CVT for passenger cars

    NARCIS (Netherlands)

    Druten, van R.M.; Tilborg, van P.G.; Rosielle, P.C.J.N.; Schouten, M.J.W.

    2000-01-01

    This paper concentrates on the design and construction aspects of a transmission for a mid-class passenger car with internal combustion engine. The transmission, consisting of a Continuously Variable Transmission (CVT) with a Van Doorne V-belt, a planetary gear set and a compact steel flywheel is

  1. Minute ventilation of cyclists, car and bus passengers: an experimental study

    Directory of Open Access Journals (Sweden)

    Hazel Peter

    2009-10-01

    Full Text Available Abstract Background Differences in minute ventilation between cyclists, pedestrians and other commuters influence inhaled doses of air pollution. This study estimates minute ventilation of cyclists, car and bus passengers, as part of a study on health effects of commuters' exposure to air pollutants. Methods Thirty-four participants performed a submaximal test on a bicycle ergometer, during which heart rate and minute ventilation were measured simultaneously at increasing cycling intensity. Individual regression equations were calculated between heart rate and the natural log of minute ventilation. Heart rates were recorded during 280 two hour trips by bicycle, bus and car and were calculated into minute ventilation levels using the individual regression coefficients. Results Minute ventilation during bicycle rides were on average 2.1 times higher than in the car (individual range from 1.3 to 5.3 and 2.0 times higher than in the bus (individual range from 1.3 to 5.1. The ratio of minute ventilation of cycling compared to travelling by bus or car was higher in women than in men. Substantial differences in regression equations were found between individuals. The use of individual regression equations instead of average regression equations resulted in substantially better predictions of individual minute ventilations. Conclusion The comparability of the gender-specific overall regression equations linking heart rate and minute ventilation with one previous American study, supports that for studies on the group level overall equations can be used. For estimating individual doses, the use of individual regression coefficients provides more precise data. Minute ventilation levels of cyclists are on average two times higher than of bus and car passengers, consistent with the ratio found in one small previous study of young adults. The study illustrates the importance of inclusion of minute ventilation data in comparing air pollution doses between

  2. Minute ventilation of cyclists, car and bus passengers: an experimental study.

    Science.gov (United States)

    Zuurbier, Moniek; Hoek, Gerard; van den Hazel, Peter; Brunekreef, Bert

    2009-10-27

    Differences in minute ventilation between cyclists, pedestrians and other commuters influence inhaled doses of air pollution. This study estimates minute ventilation of cyclists, car and bus passengers, as part of a study on health effects of commuters' exposure to air pollutants. Thirty-four participants performed a submaximal test on a bicycle ergometer, during which heart rate and minute ventilation were measured simultaneously at increasing cycling intensity. Individual regression equations were calculated between heart rate and the natural log of minute ventilation. Heart rates were recorded during 280 two hour trips by bicycle, bus and car and were calculated into minute ventilation levels using the individual regression coefficients. Minute ventilation during bicycle rides were on average 2.1 times higher than in the car (individual range from 1.3 to 5.3) and 2.0 times higher than in the bus (individual range from 1.3 to 5.1). The ratio of minute ventilation of cycling compared to travelling by bus or car was higher in women than in men. Substantial differences in regression equations were found between individuals. The use of individual regression equations instead of average regression equations resulted in substantially better predictions of individual minute ventilations. The comparability of the gender-specific overall regression equations linking heart rate and minute ventilation with one previous American study, supports that for studies on the group level overall equations can be used. For estimating individual doses, the use of individual regression coefficients provides more precise data. Minute ventilation levels of cyclists are on average two times higher than of bus and car passengers, consistent with the ratio found in one small previous study of young adults. The study illustrates the importance of inclusion of minute ventilation data in comparing air pollution doses between different modes of transport.

  3. Sound design for diesel passenger cars

    Energy Technology Data Exchange (ETDEWEB)

    Belluscio, Michele; Ruotolo, Romualdo [GM Powertrain Europe, Torino (Italy); Schoenherr, Christian; Schuster, Guenter [GM Europe, Ruesselsheim (Germany); Eisele, Georg; Genender, Peter; Wolff, Klaus; Van Keymeulen, Johan [FEV Motorentechnik GmbH, Aachen (Germany)

    2008-07-01

    With the growing market contribution of diesel passenger cars in Europe, it becomes more important to create a brand and market segment specific vehicle sound. Beside the usually considered pleasantness related topics like diesel knocking and high noise excitation, it is important to fulfil also the requirements regarding a dynamic vehicle impression. This impression is mainly influenced by the load dependency of the engine induced noise, which is reduced for diesel engines due to the missing throttle valve and the damping effect of the turbocharger and the diesel particulate filter. By means of a detailed noise transfer path analysis the contribution with dynamic potential can be identified. Furthermore the load dependency itself of a certain noise contribution can be strengthened, which allows for a dynamic sound character comparable to sporty gasoline vehicles. (orig.)

  4. Evaluation of the feasibility of using fuel cells in passenger cars

    Energy Technology Data Exchange (ETDEWEB)

    Selwood, P.G.

    2001-07-01

    This project was conceived to evaluate the commercial prospects for fuel cell powered passenger cars in the UK and Western Europe, over the time-frame to 2010. First of all the existing market place was examined and reasons for buying particular vehicles and or size of vehicle was established. The conclusion was that there was a market potential of 32,250 pa in UK (244,000 pa Western Europe) of a 'C' Sector sized car using a fuel cell engine provided it sold at no more that 1000 pounds sterling above the conventional price. (author)

  5. Emission characteristics when using bioethanol as a fuel for passenger cars

    International Nuclear Information System (INIS)

    Egebaeck, K.E.; Laurikko, J.; Ryden, C.

    1998-11-01

    In 1991 the Swedish Transport and Communication Research Board (KFB), was asked by the Swedish Government to carry out investigations and field tests in order to demonstrate the possibility of using bioethanol and biogas as automotive fuels. A five-year programme was set up for the investigations and demonstrations and the programme was later extended to a seven-year programme. Despite the fact that most of the work has been directed towards heavy-duty vehicles and especially buses in city traffic some important investigations have been carried out in order to demonstrate the use of bioethanol and biogas in passenger cars. The programme for passenger cars has consisted of running and testing 53 Flexible Fuel Vehicles (FFV), fuelled with bioethanol (E85), a project run by the Swedish Ethanol Development Foundation, and 20 other cars fuelled with biogas, a project carried out by the City of Stockholm's Material Supply Organisation, and sponsored by KFB. For both fleets of vehicles the exhaust emissions have been extensively characterised at a laboratory in Finland owned by the Technical Research Centre of Finland. The aim of this paper is to present some interesting results from the demonstrations of the use of E85 in FFV's and thereby especially focus on the results of the characterisation of both regulated and non-regulated emissions 23 refs, 16 figs, 9 tabs

  6. Emission characteristics when using bioethanol as a fuel for passenger cars

    Energy Technology Data Exchange (ETDEWEB)

    Egebaeck, K.E. [Luleaa Univ. of Technology, (Sweden); Laurikko, J. [Technical Research Centre of Finland, Helsinki (Finland); Ryden, C. [Tima, (Sweden)

    1998-11-01

    In 1991 the Swedish Transport and Communication Research Board (KFB), was asked by the Swedish Government to carry out investigations and field tests in order to demonstrate the possibility of using bioethanol and biogas as automotive fuels. A five-year programme was set up for the investigations and demonstrations and the programme was later extended to a seven-year programme. Despite the fact that most of the work has been directed towards heavy-duty vehicles and especially buses in city traffic some important investigations have been carried out in order to demonstrate the use of bioethanol and biogas in passenger cars. The programme for passenger cars has consisted of running and testing 53 Flexible Fuel Vehicles (FFV), fuelled with bioethanol (E85), a project run by the Swedish Ethanol Development Foundation, and 20 other cars fuelled with biogas, a project carried out by the City of Stockholm`s Material Supply Organisation, and sponsored by KFB. For both fleets of vehicles the exhaust emissions have been extensively characterised at a laboratory in Finland owned by the Technical Research Centre of Finland. The aim of this paper is to present some interesting results from the demonstrations of the use of E85 in FFV`s and thereby especially focus on the results of the characterisation of both regulated and non-regulated emissions 23 refs, 16 figs, 9 tabs

  7. Auralization of Accelerating Passenger Cars Using Spectral Modeling Synthesis

    Directory of Open Access Journals (Sweden)

    Reto Pieren

    2015-12-01

    Full Text Available While the technique of auralization has been in use for quite some time in architectural acoustics, the application to environmental noise has been discovered only recently. With road traffic noise being the dominant noise source in most countries, particular interest lies in the synthesis of realistic pass-by sounds. This article describes an auralizator for pass-bys of accelerating passenger cars. The key element is a synthesizer that simulates the acoustical emission of different vehicles, driving on different surfaces, under different operating conditions. Audio signals for the emitted tire noise, as well as the propulsion noise are generated using spectral modeling synthesis, which gives complete control of the signal characteristics. The sound of propulsion is synthesized as a function of instantaneous engine speed, engine load and emission angle, whereas the sound of tires is created in dependence of vehicle speed and emission angle. The sound propagation is simulated by applying a series of time-variant digital filters. To obtain the corresponding steering parameters of the synthesizer, controlled experiments were carried out. The tire noise parameters were determined from coast-by measurements of passenger cars with idling engines. To obtain the propulsion noise parameters, measurements at different engine speeds, engine loads and emission angles were performed using a chassis dynamometer. The article shows how, from the measured data, the synthesizer parameters are calculated using audio signal processing.

  8. The impact of fiscal and other measures on new passenger car sales and CO2 emissions intensity. Evidence from Europe

    International Nuclear Information System (INIS)

    Ryan, Lisa; Convery, Frank; Ferreira, Susana

    2009-01-01

    This paper examines the impact of national fiscal measures in the EU (EU15) on passenger car sales and the CO 2 emissions intensity of the new car fleet over the period 1995-2004. CO 2 emissions and energy consumption from road transport have been increasing in the EU and as a result since 1999 the EU has attempted to implement a high profile policy strategy to address this problem at European level. Less prominent is the fact that Member States apply vehicle and fuel taxes, which may also be having an impact on the quantity of passenger cars sold and their CO 2 emissions intensity. Diesel vehicle sales have increased appreciably in many countries over the same period and this study makes a first attempt to examine whether Member State fiscal measures have influenced this phenomenon. This work uses a panel dataset to investigate the relationship between national vehicle and fuel taxes on new passenger car sales and the fleet CO 2 emissions intensity in EU15 over a 10-year period. Our results show that national vehicle and fuel taxes have had an impact on passenger car sales and fleet CO 2 emissions intensity and that different taxes have disparate effects. (author)

  9. CHANGE TRENDS IN THE USE OF PASSENGER CARS ON URBAN TRIPS: CAR-POOLING IN GDYNIA

    Directory of Open Access Journals (Sweden)

    Katarzyna HEBEL

    2017-09-01

    Full Text Available The wide accessibility of European citizens to cars results in problems caused by their excessive use as a means of urban transport. Given this situation, it is necessary to find new solutions for the more efficient use of passenger cars in cities. This problem affects almost all European cities, including those in Poland. The paper analyses the level of motorization and modal split in Polish cities with county status, while selected European cities serve as a background to determine the scale of the problem. In the search of solutions in relation to Poland, an analysis of different documents outlining the directions of urban mobility was conducted. One of these documents concerned the promotion of car-pooling, the history of which dates back to the Second World War and the 1950s. Initially introduced in the USA, its increasing development in European cities has been witnessed in recent years. Research on the evaluation of real car-pooling in Polish cities was conducted in Gdynia by the authors of this study. The results of marketing research presented in the article have determined the degree to which participants in urban mobility are inclined to take part in car-pooling schemes in Polish cities.

  10. Lethal pedestrian--passenger car collisions in Berlin. Changed injury patterns in two different time intervals.

    Science.gov (United States)

    Ehrlich, Edwin; Tischer, Anja; Maxeiner, H

    2009-04-01

    To expand the passive safety of automobiles protecting traffic participants technological innovations were done in the last decades. Objective of our retrospective analysis was to examine if these technical modifications led to a clearly changed pattern of injuries of pedestrians whose death was caused by the accidents. Another reduction concerns the exclusion of injured car passengers--only pedestrians walking or standing at the moment of collision were included. We selected time intervals 1975-1985 and 1991-2004 (=years of construction of the involved passenger cars). The cars were classified depending on their frontal construction in types as presented by Schindler et al. [Schindler V, Kühn M, Weber S, Siegler H, Heinrich T. Verletzungsmechanismen und Wirkabschätzungen der Fahrzegfrontgestaltung bei Pkw-Fussgänger-Kollisionen. Abschlussbericht im Auftrag der Deutschen Versicherungswirtschaft e.V. TU-Berlin Fachgebiet Kraftfahrzeuge (GDV) 2004:36-40]. In both periods more than 90% of all cars were from the usual types small/medium/large class. Hundred and thirty-four autopsy records of such cases from Department of Forensic Medicine (Charité Berlin) data were analysed. The data included technical information of the accidents and vehicles and the external and internal injuries of the victims. The comparison of the two periods showed a decrease of serious head injuries and femoral fractures but an increase of chest-, abdominal and pelvic injuries. This situation could be explained by an increased occurrence of soft-face-constructions and changed front design of modern passenger cars, resulting in a favourable effects concerning head impact to the car during accident. Otherwise the same kinetic energy was transferred to the (complete) victim - but because of a displacement of main focus of impact the pattern of injuries modified (went distally).

  11. Energy demand and greenhouse gas emissions during the production of a passenger car in China

    International Nuclear Information System (INIS)

    Yan Xiaoyu

    2009-01-01

    Rapidly-rising oil demand and associated greenhouse gas (GHG) emissions from road vehicles in China, passenger cars in particular, have attracted worldwide attention. As most studies to date were focused on the vehicle operation stage, the present study attempts to evaluate the energy demand and GHG emissions during the vehicle production process, which usually consists of two major stages-material production and vehicle assembly. Energy demand and GHG emissions in the material production stage are estimated using the following data: the mass of the vehicle, the distribution of material used by mass, and energy demand and GHG emissions associated with the production of each material. Energy demand in the vehicle assembly stage is estimated as a linear function of the vehicle mass, while the associated GHG emission is estimated according to the primary energy sources. It is concluded that the primary energy demand, petroleum demand and GHG emissions during the production of a medium-sized passenger car in China are 69,108 MJ, 14,545 MJ and 6575 kg carbon dioxide equivalent (CO 2 -eq). Primary energy demand, petroleum demand and GHG emissions in China's passenger car fleets in 2005 would be increased by 22%, 5% and 30%, respectively, if the vehicle production stage were included.

  12. Magnesium-made door frame for passenger cars; Pkw-Tuerrahmen aus Magnesium

    Energy Technology Data Exchange (ETDEWEB)

    Tikal, F.; Vollmer, C. [Kassel Univ. (Gesamthochschule) (Germany). Inst. fuer Produktionstechnik und Logistik

    1997-11-01

    One of the most complicated parts of a car is the door. An so it will be in the future. More and more parts will be integrated in a car`s door, especially safety and comfort related parts as well as a big number of functional elements. The car industry tries intensively to bring about a growing safety image to its buyers. At the Institute for Technical Production and Logistics (IPL) of the University of Kassel (GhK) a passenger door construction out of magnesium has been developed on the base of a foregoing construction. With the new practice orientated model the time of production could be essentially reduced while at the same time the weight could be decreased. (orig.) [Deutsch] Am Institut fuer Produktionstechnik und Logistik (ipl) der Universitaet Gesamthochschule Kassel wurde ein optimierter Magnesium-Druckguss-Rahmen fuer eine Pkw-Tuer, basierend auf einer vorangegangenen Arbeit, entwickelt. Mit dem neuen praxisnahen Modell konnte die Montagezeit erheblich reduziert und Gewicht eingespart werden. (orig.)

  13. MACRO MODEL OF SEAT BELT USE BY CAR DRIVERS AND PASSENGERS

    Directory of Open Access Journals (Sweden)

    Kazimierz JAMROZ

    2013-12-01

    Full Text Available The article presents some problems of seat belt use by car drivers and passengers. It looks in particular at seat belt use and effectiveness in selected countries. Next, factors of seat belt use are presented and methodology of model development. A macro model of seat belt use is presented based on data from around fifty countries from different continents.

  14. Computation of thermal comfort inside a passenger car compartment

    International Nuclear Information System (INIS)

    Mezrhab, A.; Bouzidi, M.

    2006-01-01

    This paper describes a numerical model to study the behaviour of thermal comfort inside the passenger car compartment according to climatic conditions and materials that compose the vehicle. The specifically developed numerical model is based on the nodal method and the finite difference method. Its specificities are: (i) the transient mode, (ii) the taking into account of the combined convection, conduction and radiation heat transfer, (iii) the coupling of two spectral bands (short-wave and long-wave radiation) and two solar fluxes (beam and diffuse). The compartment is subdivided in several solid nodes (materials constituting the compartment) and fluid nodes (volumes of air inside the compartment). The establishment of the heat balance for each node gives the evolution of its temperature. Effects of solar radiation, types of glazing, car colour and radiative properties of materials constituting the compartment are investigated

  15. Integrated assessment of energy efficiency technologies and CO_2 abatement cost curves in China’s road passenger car sector

    International Nuclear Information System (INIS)

    Peng, Bin-Bin; Fan, Ying; Xu, Jin-Hua

    2016-01-01

    Highlights: • Energy efficiency technologies in Chinese passenger cars are classified in detail. • CO_2-reduction potential and abatement cost are analyzed for technology bundles. • Marginal abatement cost curve is established from both micro and macro perspectives. • Spark ignition, diesel and hybrid electric vehicle paths should be firstly promoted. • Technology promotion should start from the area of taxies and high-performance cars. - Abstract: Road transport is one of the main sources of energy consumption and CO_2 emissions. It is essential to conserve energy and reduce emissions by promoting energy efficiency technologies (EETs) in this sector. This study first identifies EETs for the passenger cars and then classifies them into various technology bundles. It then analyzes the CO_2-reduction potentials and emissions abatement costs of 55 type-path, 246 type-path-technology, and 465 type-path-subtechnology bundles from micro-vehicular and macro-industrial perspectives during 2010–2030, based on which marginal abatement cost (MAC) curve for China’s road passenger car sector is established. Results show that the cumulative CO_2-reduction potential of EETs on passenger cars in China during 2010–2030 is about 2698.8 Mt, but only 4% is cost-effective. The EETs with low emissions abatement costs are mainly available in the spark ignition (SI), diesel, and hybrid electric vehicle (HEV) paths on the taxis and high-performance cars, and also in the transmission, vehicle body and SI technologies on the private cars, which could be promoted at present. The technologies with large emissions reduction potential are mainly available in the plug-in hybrid electric vehicle (PHEV) and electric vehicle (EV) paths, which would be the main channels for reducing carbon emissions in the long run.

  16. Energy Chain Analysis of Passenger Car Transport

    Directory of Open Access Journals (Sweden)

    Hans Jakob Walnum

    2011-02-01

    Full Text Available Transport makes up 20 percent of the World’s energy use; in OECD countries this has exceeded 30 percent. The International Energy Agency (IEA estimates that the global energy consumption will increase by 2.1 percent annually, a growth rate that is higher than for any other sector. The high energy consumption means that transportation accounts for nearly 30 percent of CO2 emission in OECD countries and is also one of the main sources of regional and local air pollution. In this article, we analyze energy consumption and greenhouse gas emissions from passenger car transport using an energy chain analysis. The energy chain analysis consists of three parts: the net direct energy use, the energy required for vehicle propulsion; the gross direct chain, which includes the net direct energy consumption plus the energy required to produce it; and, finally, the indirect energy chain, which includes the energy consumption for production, maintenance and operation of infrastructure plus manufacturing of the vehicle itself. In addition to energy consumption, we also analyze emissions of greenhouse gases measured by CO2-equivalents. We look at the trade-offs between energy use and greenhouse gas emissions to see whether some drivetrains and fuels perform favourable on both indicators. Except for the case of electric cars, where hydropower is the only energy source in the Norwegian context, no single car scores favourably on both energy consumption and greenhouse gas emissions.

  17. Policy options to reduce passenger car CO2 emissions after 2020

    Energy Technology Data Exchange (ETDEWEB)

    De Wilde, H.P.J.; Kroon, P. [ECN Beleidsstudies, Petten (Netherlands)

    2013-02-15

    The EU has set emission targets for new cars up to 2020 and is now preparing the post 2020 legislation. The present study aims to give insight in the design of policies to further reduce passenger car emissions after 2020. Internal combustion engine (ICE) vehicles are now expected to enable deeper and less costly CO2 emission reductions than envisioned until recently. However, even advanced ICE vehicles will not enable to meet the very stringent long term emission reduction targets for passenger cars. Therefore transport policies need not only to reduce emissions of ICE vehicles, but also ensure that electric and hydrogen vehicles are phased in timely, along with low-CO2 electricity and hydrogen. Current legislation to regulate tank-to-wheel vehicle emissions is based on CO2-limits, expressed in g CO2/km. On the short term it is important to maximize the efficiency of conventional vehicles. At the same time it is essential to foster the market introduction of electric and hydrogen vehicles, given their potential to reach eventually much deeper overall CO2-reductions. When the market share of electric and hydrogen vehicles grows it becomes increasingly important to maximize their efficiency and to minimize their upstream CO2 emissions. Maximizing both efficiency and overall CO2-performance of all vehicle types - ICE, electric, and hydrogen - will be complicated to achieve with a single CO2-based standard. At this point an efficiency-based standard is more effective, and may offer some additional benefits too. The current report provides basic directions of how such legislation could be shaped.

  18. From Laboratory to Road. A 2014 update of official and real-world fuel concumption and CO2 values for passenger cars in Europe

    NARCIS (Netherlands)

    Mock, P.; Tietge, U.; Franco, V.; German, J.; Bandivadekar, A.; Ligterink, N.E.; Lambrecht, U.; Kuhlwein, J.; Riemersma, I.

    2014-01-01

    Europe’s passenger-car efficiency regulation has very effectively driven down the official average CO2 emissions and fuel consumption of new passenger cars in the EU. The 2015 target of 130 grams of CO2 per kilometer (g/km) was met two years ahead of schedule and manufacturers are making good

  19. Simulating the impact of policy, energy prices and technological progress on the passenger car fleet in Austria-A model based analysis 2010-2050

    International Nuclear Information System (INIS)

    Kloess, Maximilian; Mueller, Andreas

    2011-01-01

    This paper investigates the effects of policy, fuel prices and technological progress on the Austrian passenger car fleet in terms of energy consumption and greenhouse gas (GHG) emissions. To analyse these effects a simulation model is used. We model the car fleet from a bottom-up perspective, with a detailed coverage of vehicle specifications and propulsion technologies. The model focuses on the technological trend toward electrified propulsion systems and their potential effects on the fleet's energy consumption and GHG emissions. To represent the impact of prices and income on the development of the fleet, we combine the fleet model with top-down demand models. We developed two scenarios for the time frame 2010-2050, using two different sets of assumptions for regulatory development and conditions of increasing fossil fuel prices and continuous technological progress in vehicle propulsion technologies. The results indicate that material cuts in energy consumption and GHG emissions can be achieved with changes to the political framework for passenger cars. Appropriate taxation of fuels and cars can stabilise demand for individual motorised transport and lead to an improvement in vehicle efficiency by fostering the adoption of efficient vehicle propulsion technologies and low carbon fuels. - Highlights: → We present a simulation model for future energy demand and greenhouse gas emissions in passenger car transport. → We develop scenarios up to 2050 assuming two different policy schemes. → Policy strongly affects energy demand and greenhouse gas emissions in passenger car transport. → Policy can slow down growth in demand for passenger car transport. → Policy can promote the diffusion of more efficient propulsion technologies and low carbon fuels.

  20. 49 CFR 238.311 - Single car test.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Single car test. 238.311 Section 238.311... Requirements for Tier I Passenger Equipment § 238.311 Single car test. (a) Except for self-propelled passenger cars, single car tests of all passenger cars and all unpowered vehicles used in passenger trains shall...

  1. Analysis of Passenger Car Emission Factors in RDE Tests

    Directory of Open Access Journals (Sweden)

    Pielecha Jacek

    2016-01-01

    Full Text Available The article presents a study on emission measurements in passenger cars in tests conducted under real traffic conditions – Real Driving Emissions using a Portable Emission Measurement System type of equipment. A special feature of the outlined RDE tests is that they were performed in Polish road conditions, and thus their parameters may differ from their counterparts adopted in most European Union countries. Based on the findings vehicle emission conformity factors were developed, characterized as the fractional increase (or decrease of traffic emissions during the homologation test or under normal operation conditions in relation to the emission limit standards (for chosen emission class of the vehicle. Conducted research and the calculated conformity factors allowed for the environmental impact assessment of the vehicles of various emission classes, while also allowing early actions to restrict the emissions of selected components in passenger vehicles. The methods and measures used can also be applied to other types of vehicles (e.g. heavy duty or off-road vehicles or vehicles powered by other fuels.

  2. Natural refrigerants for air conditioners in passenger cars. A contribution to climate protection. Background; Natuerliche Kaeltemittel fuer PKW-Klimaanlagen. Ein Beitrag zum Klimaschutz. Hintergrund

    Energy Technology Data Exchange (ETDEWEB)

    Hoffmann, Gabriele; Plehn, Wolfgang

    2010-09-15

    Air conditioners in passenger cars contain a refrigerant which significantly increases the greenhouse effect. Currently about 30 % of global emissions of partially fluorinated hydrocarbons originate from these air conditioners. According to the directive 2006/40/EC, this refrigerant must be replaced by a less harmful substance. Under this aspect, the contribution under consideration initially reports on the stock and level of air conditioning of passenger cars as well as on the refrigerant tetrafluoroethane. Subsequently, refrigerants for air conditioning of passenger cars such as carbon dioxide, 1.1-difluoroethane and 2,3,3,3-tetrafluoro propylene are described. Overall, the refrigerant carbon dioxide is the best alternative for mobile air conditioning.

  3. Localized innovation, localized diffusion and the environment : an analysis of reductions of CO(2) emissions by passenger cars

    NARCIS (Netherlands)

    Los, B.; Verspagen, B.

    We investigate technological change with regard to CO(2) emissions by passenger cars, using a Free Disposal Hull methodology to estimate technological frontiers. We have a sample of cars available in the UK market in the period 2000-2007. Our results show that the rates of technological change

  4. The Impact of Drive Cycles and Auxiliary Power on Passenger Car Fuel Economy

    Directory of Open Access Journals (Sweden)

    Thomas Grube

    2018-04-01

    Full Text Available In view of the advancement of zero emission transportation and current discussions on the reliability of nominal passenger car fuel economy, this article considers the procedure for assessing the potential for reducing the fuel consumption of passenger cars by using electric power to operate them. The analysis compares internal combustion engines, hybrid and fully electric concepts utilizing batteries and fuel cells. The starting point for the newly developed, simulation-based fuel consumption analysis is a longitudinal vehicle model. Mechanical power requirements on the drive side incorporate a large variety of standardized drive cycles to simulate typical patterns of car usage. The power requirements of electric heating and air conditioning are also included in the simulation, as these are especially relevant to electric powertrains. Moreover, on-board grid-load profiles are considered in the assessment. Fuel consumption is optimized by applying concept-specific operating strategies. The results show that the combination of low average driving speed and elevated onboard power requirements have severe impacts on the fuel efficiency of all powertrain configurations analyzed. In particular, the operational range of battery-electric vehicles is strongly affected by this due to the limited storage capacity of today’s batteries. The analysis confirms the significance of considering different load patterns of vehicle usage related to driving profiles and onboard electrical and thermal loads.

  5. Developing infrastructure for electric passenger-cars in the corridor between Southern Scandinavia and Germany

    DEFF Research Database (Denmark)

    Guasco, Clement; Jespersen, Per Homann; Lohse, Sandrina

    2012-01-01

    and academic institutions. A strategy for the development of infrastructure for electric passenger-cars in the corridor was formed using the “Future Creating” methodology. The workshop was part of the SCANDRIA Action Programme and pointed towards ways for e-mobility in the region. The workshop also provided...

  6. Secondhand smoke in cars: assessing children's potential exposure during typical journey conditions.

    Science.gov (United States)

    Semple, Sean; Apsley, Andrew; Galea, Karen S; MacCalman, Laura; Friel, Brenda; Snelgrove, Vicki

    2012-11-01

    To measure levels of fine particulate matter in the rear passenger area of cars where smoking does and does not take place during typical real-life car journeys. Fine particulate matter (PM(2.5)) was used as a marker of secondhand smoke and was measured and logged every minute of each car journey undertaken by smoking and non-smoking study participants. The monitoring instrument was located at breathing zone height in the rear seating area of each car. Participants were asked to carry out their normal driving and smoking behaviours over a 3-day period. 17 subjects (14 smokers) completed a total of 104 journeys (63 smoking journeys). Journeys averaged 27 min (range 5-70 min). PM(2.5) levels averaged 85 and 7.4 μg/m(3) during smoking and non-smoking car journeys, respectively. During smoking journeys, peak PM(2.5) concentrations averaged 385 μg/m(3), with one journey measuring over 880 μg/m(3). PM(2.5) concentrations were strongly linked to rate of smoking (cigarettes per minute). Use of forced ventilation and opening of car windows were very common during smoking journeys, but PM(2.5) concentrations were still found to exceed WHO indoor air quality guidance (25 μg/m(3)) at some point in the measurement period during all smoking journeys. PM(2.5) concentrations in cars where smoking takes place are high and greatly exceed international indoor air quality guidance values. Children exposed to these levels of fine particulate are likely to suffer ill-health effects. There are increasing numbers of countries legislating against smoking in cars and such measures may be appropriate to prevent the exposure of children to these high levels of secondhand smoke.

  7. Localized Innovation, Localized Diffusion and the Environment: An Analysis of CO2 Emission Reductions by Passenger Cars, 2000-2007

    OpenAIRE

    Los, Bart; Verspagen, Bart

    2008-01-01

    We investigate technological change with regard to CO2 emissions by passenger cars, using a Free Disposal Hull methodology to estimate technological frontiers. We have a sample of cars available in the UK market in the period 2000 – 2007. Our results show that the rates of technological change (frontier movement) and diffusion (distance to frontier at the car brand level) differ substantial between segments of the car market. We conclude that successful policies should be aimed at diffusion o...

  8. Car seat inspection among children older than 3 years: Using data to drive practice in child passenger safety.

    Science.gov (United States)

    Kroeker, Amber M; Teddy, Amy J; Macy, Michelle L

    2015-09-01

    Motor vehicle crashes are the leading cause of unintentional death and disability among children 4 years to 12 years of age in the United States. Despite the high risk of injury from motor vehicle crashes in this age group, parental awareness and child passenger safety programs in particular may lack focus on this age group. This is a retrospective cross-sectional analysis of child passenger safety seat checklist forms from two Safe Kids coalitions in Michigan (2013) to identify restraint type upon arrival to car seat inspections. Other variables were included if the coalition provided a new child safety seat and if the child had a sibling who underwent a car seat inspection. χ statistics were used to compare change in restraint use on arrival and at departure, the proportion of children attending a car seat inspection event by age, the age category of children by site, the proportion of children with siblings also undergoing a car seat inspection by age, and the distribution of a new child safety seat by age. Data were available from 1,316 Safe Kids Huron Valley and 3,215 Safe Kids Greater Grand Rapids car seat inspections. Just 10.8% of the total seats inspected were booster seats. Child safety seats for infant and young children were more commonly inspected (rear-facing carrier [40.3%], rear-facing convertible [10.2%], and forward-facing [19.3%] car seats). Few children at inspections used a seat belt only (5.4%) or had no restraint (13.8%). Children 4 years and older were found to be in a suboptimal restraint at least 30% of the time. Low proportions of parents use car seat inspections for children in the booster seat age group. The proportion of children departing the inspection in a more protective restraint increased with increasing age. This highlights an area of weakness in child passenger safety programs and signals an opportunity to strengthen efforts on The Booster Age Child. Epidemiologic/prognostic study, level III.

  9. Measurement of black carbon emissions from in-use diesel-electric passenger locomotives in California

    Science.gov (United States)

    Tang, N. W.; Kirchstetter, T.; Martien, P. T.; Apte, J.

    2015-12-01

    Black carbon (BC) emission factors were measured for a California commuter rail line fleet of diesel-electric passenger locomotives (Caltrain). The emission factors are based on BC and carbon dioxide (CO2) concentrations in the exhaust plumes of passing locomotives, which were measured from pedestrian overpasses using portable analyzers. Each of the 29 locomotives in the fleet was sampled on 4-20 separate occasions at different locations to characterize different driving modes. The average emission factor expressed as g BC emitted per kg diesel consumed was 0.87 ± 0.66 g kg-1 (±1 standard deviation, n = 362 samples). BC emission factors tended to be higher for accelerating locomotives traveling at higher speeds with engines in higher notch settings. Higher fuel-based BC emission factors (g kg-1) were measured for locomotives equipped with separate "head-end" power generators (SEP-HEPs), which power the passenger cars, while higher time-based emission factors (g h-1) were measured for locomotives without SEP-HEPs, whose engines are continuously operated at high speeds to provide both head-end and propulsion power. PM10 emission factors, estimated assuming a BC/PM10 emission ratio of 0.6 and a typical power output-to-fuel consumption ratio, were generally in line with the Environmental Protection Agency's locomotive exhaust emission standards. Per passenger mile, diesel-electric locomotives in this study emit only 20% of the CO2 emitted by typical gasoline-powered light-duty vehicles (i.e., cars). However, the reduction in carbon footprint (expressed in terms of CO2 equivalents) due to CO2 emissions avoidance from a passenger commuting by train rather than car is appreciably offset by the locomotive's higher BC emissions.

  10. Decomposition analysis of CO2 emissions from passenger cars: The cases of Greece and Denmark

    International Nuclear Information System (INIS)

    Papagiannaki, Katerina; Diakoulaki, Danae

    2009-01-01

    The paper presents a decomposition analysis of the changes in carbon dioxide (CO 2 ) emissions from passenger cars in Denmark and Greece, for the period 1990-2005. A time series analysis has been applied based on the logarithmic mean Divisia index I (LMDI I) methodology, which belongs to the wider family of index decomposition approaches. The particularity in road transport that justifies a profound analysis is its remarkably rapid growth during the last decades, followed by a respective increase in emissions. Denmark and Greece have been selected based on the challenging differences of specific socio-economic characteristics of these two small EU countries, as well as on the availability of detailed data used in the frame of the analysis. In both countries, passenger cars are responsible for half of the emissions from road transport as well as for their upward trend, which provokes the implementation of a decomposition analysis focusing exactly on this segment of road transport. The factors examined in the present decomposition analysis are related to vehicles ownership, fuel mix, annual mileage, engine capacity and technology of cars. The comparison of the results discloses the differences in the transportation profiles of the two countries and reveals how they affect the trend of CO 2 emissions.

  11. Evaluation of the environmental impact of modern passenger cars on petrol, diesel, automotive LPG and CNG

    NARCIS (Netherlands)

    Hendriksen, P.; Vermeulen, R.J.; Rijkeboer, R.C.; Bremmers, D.A.C.M.; Smokers, R.T.M.; Winkel, R.G.

    2003-01-01

    The project reported here concerns an investigation into the environmental performance of modern passenger cars on four different fuels: petrol, diesel, automotive LPG and CNG. The objectives of the project were twofold: - To make a valid and useful comparison between modern vehicles fuelled by

  12. Experimental Assessment of NOx Emissions from 73 Euro 6 Diesel Passenger Cars.

    Science.gov (United States)

    Yang, Liuhanzi; Franco, Vicente; Mock, Peter; Kolke, Reinhard; Zhang, Shaojun; Wu, Ye; German, John

    2015-12-15

    Controlling nitrogen oxides (NOx) emissions from diesel passenger cars during real-world driving is one of the major technical challenges facing diesel auto manufacturers. Three main technologies are available for this purpose: exhaust gas recirculation (EGR), lean-burn NOx traps (LNT), and selective catalytic reduction (SCR). Seventy-three Euro 6 diesel passenger cars (8 EGR only, 40 LNT, and 25 SCR) were tested on a chassis dynamometer over both the European type-approval cycle (NEDC, cold engine start) and the more realistic Worldwide harmonized light-duty test cycle (WLTC version 2.0, hot start) between 2012 and 2015. Most vehicles met the legislative limit of 0.08 g/km of NOx over NEDC (average emission factors by technology: EGR-only 0.07 g/km, LNT 0.04 g/km, and SCR 0.05 g/km), but the average emission factors rose dramatically over WLTC (EGR-only 0.17 g/km, LNT 0.21 g/km, and SCR 0.13 g/km). Five LNT-equipped vehicles exhibited very poor performance over the WLTC, emitting 7-15 times the regulated limit. These results illustrate how diesel NOx emissions are not properly controlled under the current, NEDC-based homologation framework. The upcoming real-driving emissions (RDE) regulation, which mandates an additional on-road emissions test for EU type approvals, could be a step in the right direction to address this problem.

  13. On the way to 130 g CO2/km-Estimating the future characteristics of the average European passenger car

    International Nuclear Information System (INIS)

    Fontaras, Georgios; Samaras, Zissis

    2010-01-01

    A new average CO 2 emissions limit for passenger cars was introduced in EU in 2009 imposing gradual average CO 2 emissions reduction to 130 g/km until 2015. This paper attempts to study possible changes in vehicle characteristics for meeting this limit taking into account the average European passenger car of 2007-2008. For this purpose first the most important factors affecting vehicle fuel consumption over the reference cycle (NEDC) are identified. At a second step, the CO 2 benefit from the optimisation of these factors is quantified, through simulations of 6 different passenger cars commonly found in the European fleet. For the simulations Advisor 2002 was employed and validated against published type approval data. The analysis indicated that substantial reductions in vehicle weight, tyre rolling resistance and engine efficiency are necessary to reach even the 2008 target. A 10% reduction in average vehicle weight combined with 10% better aerodynamic characteristics, 20% reduced tyre rolling resistance and a 7.5% increase in average powertrain efficiency can lead to CO 2 reductions of approximately 13% (about 138 g/km based on 2007-2008 fleet-wide performance). Complying with the 130 g/km within the next six-year timeframe will be a rather difficult task and additional technical measures appear to be necessary.

  14. Exposure to in-vehicle respirable particulate matter in passenger vehicles under different ventilation conditions and seasons

    Directory of Open Access Journals (Sweden)

    Suresh Jain

    2017-03-01

    Full Text Available This study presents the in-vehicle particulate matter (PM concentration in a number of passenger vehicles under various ventilation modes, land use land cover (LULC in different seasons in megacity Delhi, India. In-vehicle monitoring was conducted in buses, cars and autos (three-wheeler using air-conditioned (AC and Non-AC during peak and off-peak hours. The site selected is a ∼15 km long stretch from Punjabi Bagh to Safdarjung Hospital, based on diversity in LULC, availability of vehicles and heavy traffic flow along the direction of travelling. In-vehicle PM was measured using GRIMM aerosol spectrometer and categorised in three classes (PM1, PM2.5 and PM10. The study found that concentration of PM1, PM2.5 and PM10 were significantly (p ≤ 0.05 higher in winters as compared to summers. It was observed that PM concentration was significantly (p ≤ 0.05 higher in Non-AC travel modes compared to AC modes. PM concentrations were high near industrial and commercial areas and during traffic congestion showing the influence of LULC. It is also important to highlight that PM1, PM2.5 and PM10 concentrations were significantly (p ≤ 0.05 higher in case of taxis (cars compared to personal cars which varied from 2.5 to 3.5 times higher in case of AC mode and ∼1.5 times in case of Non-AC mode. Exposures to PM concentration were highest in case of Non-AC bus compared AC-Bus, Non-AC cars, autos and AC-cars. PM concentrations in case of autos and Non-AC cars were almost comparable without any significant (p > 0.05 difference. Regression analysis showed significant correlation between ambient and in-vehicle concentration for PM2.5. Regional deposition fractions were calculated using International Commission on Radiological Protection model to show the deposition in head air-pass, trachea-bronchial and alveolar regions. It was found that deposition of PM1 was highest in the alveolar region.

  15. Increasing fuel efficiency of passenger cars with the “climate-control” system as a method of improving the ecological safety of the urban infrastructure

    Science.gov (United States)

    Burakova, L. N.; Burakova, A. D.; Burakova, O. D.; Dovbysh, V. O.

    2018-01-01

    Motor vehicle should provide safety and a high ecological standard of living for the population. One of the methods to improve the ecological friendliness of motor vehicles in particular passenger cars (cars), which are considered in this article, is the growth of their fuel economy. It is established that fuel consumption and the amount of specific emissions of harmful substances with exhaust gases of cars when using the “climate control” system depend on the effective ambient temperature, the color of the opaque car body elements, the power of the car engine and the interior volume. However, the simplest controlled factor is the color of the opaque car body elements, which is characterized by the coefficient of light reflection. In the course of experimental studies, we established the dependences of a change in fuel consumption and a share of reducing emissions of harmful substances with exhaust gases of passenger cars with the “climate control” system on the coefficient of light reflection. A method has been developed to reduce fuel consumption and the amount of specific emissions of harmful substances with the exhaust gases of passenger cars when using the “climate control” system, which involves painting the vehicle roof white and allows reducing fuel consumption by 5.5-10.3% and the amount of specific emissions of harmful substances by 0.37-1.13% (CO) and 0.47-1.08% (CH).

  16. Relationship Between Vehicle Size and Fatality Risk in Model Year 1985-93 Passenger Cars and Light Trucks

    Science.gov (United States)

    1997-01-01

    Fatality rates per million exposure years are computed by make, model and model year, : based on the crash experience of model year 1985-93 passenger cars and light trucks (pickups) vans : and sport utility vehicles) in the United States during calen...

  17. Driving cycles for measuring passenger car emissions on roads with traffic calming measures

    International Nuclear Information System (INIS)

    Boulter, P.G.; Latham, S.; Ainge, M.

    1999-01-01

    Although local authorities in the UK need to be aware of any air quality impacts resulting from their traffic calming operations, there is little information relating to the effects of different traffic calming measures. The effects on air quality on this scale are complex, and so TRL is providing guidance by developing performance indices for different measures based on their effects on vehicle emissions. The emissions indices for passenger cars are based on tests conducted on a chassis dynamometer, and this paper describes the development of the methodology for constructing the driving cycles to be used. The technique involves the measurement of the speed profiles of a large number of vehicles using a roadside LIDAR system, and the determination of typical gear selections using three-instrumented cars

  18. Developing infrastructure for electric passenger-cars in the corridor between Southern Scandinavia and Germany - Workshop Protocol

    DEFF Research Database (Denmark)

    Guasco, Clement; Jespersen, Per Homann; Lohse, Sandrina

    2012-01-01

    and academic institutions. A strategy for the development of infrastructure for electric passenger-cars in the corridor was formed using the “Future Creating” methodology. The workshop was part of the SCANDRIA Action Programme and pointed towards ways for e-mobility in the region. The workshop also provided...

  19. The effectiveness of lane departure warning systems-A reduction in real-world passenger car injury crashes.

    Science.gov (United States)

    Sternlund, Simon; Strandroth, Johan; Rizzi, Matteo; Lie, Anders; Tingvall, Claes

    2017-02-17

    The objective of this study was to estimate the safety benefits of in vehicle lane departure warning (LDW) and lane keeping aid (LKA) systems in reducing relevant real-world passenger car injury crashes. The study used an induced exposure method, where LDW/LKA-sensitive and nonsensitive crashes were compared for Volvo passenger cars equipped with and without LDW/LKA systems. These crashes were matched by car make, model, model year, and technical equipment; that is, low-speed autonomous emergency braking (AEB) called City Safety (CS). The data were extracted from the Swedish Traffic Accident Data Acquisition database (STRADA) and consisted of 1,853 driver injury crashes that involved 146 LDW-equipped cars, 11 LKA-equipped cars, and 1,696 cars without LDW/LKA systems. The analysis showed a positive effect of the LDW/LKA systems in reducing lane departure crashes. The LDW/LKA systems were estimated to reduce head-on and single-vehicle injury crashes on Swedish roads with speed limits between 70 and 120 km/h and with dry or wet road surfaces (i.e., not covered by ice or snow) by 53% with a lower limit of 11% (95% confidence interval [CI]). This reduction corresponded to a reduction of 30% with a lower limit of 6% (95% CI) for all head-on and single-vehicle driver injury crashes (including all speed limits and all road surface conditions). LDW/LKA systems were estimated to lower the driver injury risk in crash types that the systems are designed to prevent; that is, head-on and single-vehicle crashes. Though these are important findings, they were based on a small data set. Therefore, further research is desirable to evaluate the effectiveness of LDW/LKA systems under real-world conditions and to differentiate the effectiveness between technical solutions (i.e., LDW and LKA) proposed by different manufacturers.

  20. REDUCING ENERGY CONSUMPTION BY PASSENGER CAR WITH USING OF NON-ELECTRICAL HYBRID DRIVE TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    Tomas Skrucany

    2017-03-01

    Full Text Available Not only electrical hybrid technology is used for drivetrain of passenger cars. Also other systems using non-electrical principles (hydraulic or air pressure, mechanical energy storage can be found in current vehicles. There is a quantification of the spared energy by using a hybrid vehicle in the paper. Driving cy-cle ECE 15 was chosen as a platform for simulation of driving resistances.

  1. Post-consumer tires back into new tires: de-vulcanization and re-utilization of passenger car tires

    NARCIS (Netherlands)

    Saiwari, Sitisaiyidah

    2013-01-01

    Enabling recycling loops for used passenger car tires is a challenge and an opportunity. The challenge lies in the presence of SBR as the main elastomer in this type of tires, which makes this material difficult to reclaim due to the tendency of the elastomer chain fragments to re-combine. The

  2. CO_2 labelling of passenger cars in Europe: Status, challenges, and future prospects

    International Nuclear Information System (INIS)

    Haq, Gary; Weiss, Martin

    2016-01-01

    Directive 1999/94/EC requires Member States of the European Union (EU) to ensure that consumers are informed about the fuel consumption and CO_2 emissions of new passenger cars. The European Commission is currently evaluating the directive. In support of this effort, we assess the status of car labelling in the EU. We find that all EU Member States have formally implemented national car labelling schemes. However, relevant information is not presented to consumers in a uniform manner. Only 13 Member States have implemented graphic labels that differ in their design, metrics, and classification of vehicles. The fuel consumption data displayed to consumers underrate yearly fuel costs in the order of several hundred Euros per car. We argue that car labelling can be made more effective if Member States adopt: (i) a uniform label that mirrors, as far as feasible, the design of the EU energy label, (ii) data and classification metrics that accurately reflect the fuel consumption and CO_2 emissions observed by consumers, and (iii) a labelling scale that allows differentiation between efficient hybrid and plug-in hybrid vehicles. By following these recommendations, the European car labelling can receive wider recognition and foster well-informed consumer choices. - Highlights: •Car labelling Directive 1999/94 implemented by all 28 EU Member States. •National labelling schemes vary from each other in design and amount of information displayed to consumers. •Future revisions should ensure labelling accurately reflects on-road energy use and CO_2 emissions of cars. •Expansion of labelling scale toward zero CO_2 emissions would allow differentiating between hybrid and plug-in hybrid cars.

  3. 78 FR 10687 - Notice of Receipt of Petition for Decision That Nonconforming 1992 Porsche Carrera Passenger Cars...

    Science.gov (United States)

    2013-02-14

    ... Defrosting and Defogging Systems, 104 Windshield Wiping and Washing Systems, 106 Brake Hoses, 113 Hood Latch... vehicle is equipped with an automatic restraint system that consists of dual front airbags and knee... Passenger Cars Are Eligible for Importation AGENCY: National Highway Traffic Safety Administration, DOT...

  4. Alternative fuels from forest residues for passenger cars - an assessment under German framework conditions

    OpenAIRE

    Hurtig, O.; Leible, L.; Kälber, S.; Kappler, g.; Spicher, U.

    2014-01-01

    Background Due to the available volumes, biogenic residues are a promising resource for renewable fuels for passenger cars to reduce greenhouse gas (GHG) emissions. In this study, we compare three fuels from forest residues under German framework conditions: biogenic electricity, substitute natural gas (SNG), and Fischer-Tropsch (FT) diesel. Methods Fuels from forest residues are compared with regard to their technical efficiency (here defined as ‘pkm per kg b...

  5. Developing Singapore Driving Cycle for passenger cars to estimate fuel consumption and vehicular emissions

    Science.gov (United States)

    Ho, Sze-Hwee; Wong, Yiik-Diew; Chang, Victor Wei-Chung

    2014-11-01

    Singapore has pledged to attain 7-11% Business-As-Usual carbon emissions reduction by 2020. Road transport sector is a significant source of carbon emissions, estimated to be the third largest sector in Singapore. A current gap in environmental evaluation for road transport activities in Singapore is the lack of a representative driving cycle for passenger cars (64% of the total population of 974,170 vehicles). This Singapore Driving Cycle (SDC) is hence developed for Singapore roads and traffic conditions. A chase-car (instrumented vehicle) was used to collect on-road data along 12 designed routes, and circulation driving on highly utilized arterial roads (including those in Central Business District (CBD) and both inner and outer ring roads fringing the CBD area). The SDC was thus hence constructed, with consideration of road type proportions, time periods and desired distance, duration and peak-lull proportion. In essence, the SDC is a 2400-s speed-time profile to represent the driving pattern for passenger car in Singapore. Microscopic estimation model (CMEM) shows that, as compared to SDC, the New European Driving Cycle (NEDC) underestimates most of the vehicular emissions (fuel, CO2, HC and NOx by 5%, 5%, 22% and 47%, respectively) and overestimates CO by 8%. The SDC is thus more suitable than the NEDC that is currently in use in Singapore; the SDC can be used to generate more accurate fuel consumption and emissions ratings for various uses (for example, inventory of vehicular emissions and fuel economy labelling).

  6. Solar Powered Heat Control System for Cars

    OpenAIRE

    Abin John; Jithin Thomas

    2014-01-01

    It takes times for an air-conditioner to effectively start cooling the passenger compartment in the car. So the passenger of the car will feel the heat in the car extremely before the air-conditioner fully cooling the interior of the car. Excessive heat can also damage an automobile's interior as well as personal property kept in the passenger compartment. So, a system to reduce this excessive heat by pumping out hot air and allowing cooler ambient air to enter the car by mean...

  7. Airborne Wear Particles Emissions fromCommercial Disc Brake Materials– Passenger Car Field Test

    OpenAIRE

    Wahlström, Jens; Olofsson, Ulf; Jansson, Anders; Olander, Lars

    2008-01-01

    Most modern passenger cars have disc brakes on the front wheels, which unlike drum brakes are not sealed off to the ambient air. During braking, there is wear to both the rotor and the pads. This wear process generates particles, which may become airborne. In field tests it is difficult to distinguish these particles from others in the surrounding environment. It may be preferable to use laboratory test stands where the cleanness of the surrounding air can be controlled. The validity of these...

  8. Fuel economy of new passenger cars in Mexico: Trends from 1988 to 2008 and prospects

    International Nuclear Information System (INIS)

    Sheinbaum-Pardo, Claudia; Chávez-Baeza, Carlos

    2011-01-01

    This paper analyzes trends in fuel economy (kilometers per liter) of new passenger vehicles in Mexico over a period of 20 years from 1988 to 2008. Results show that in this period, fuel economy of the new passenger vehicle fleet, including multipurpose vehicles (a category similar to sport utility vehicles, SUVs), increased by only 6.3%. A simple Laspeyres index analysis was developed to evaluate both the impact of changes in vehicle sales structure by category and the changes in fuel economy. Results show that increased sales of heavier, multipurpose vehicles in place of subcompact and compact vehicles, impacted negatively on the fleet average fuel economy. If the structure of sales had continued in the same proportions across all categories as in 1988, fuel economy would have increased by 11.0%, instead of the actual 6.3%. This result coincides with trends in other countries. The paper also presents different scenarios of passenger car fuel economy for the year 2020, and its implications for gasoline consumption and CO 2 emissions. The results may influence the new passenger vehicle fuel economy standard that is currently under discussion in Mexico.

  9. Effect of Aromatic Oil on Phase Dynamics of S-SBR/BR Blends fro Passenger Car Tire Treads

    NARCIS (Netherlands)

    Rathi, Akansha; Hernández, M.; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.; Bergmann, C.; Trimbach, J.; Blume, Anke

    2015-01-01

    Even though S-SBR/BR blends are commonly used for passenger car tire treads, little is known about the phase dynamics arising from the local morphological heterogeneities. The present study aims at developing the understanding of: (i) the influence of aromatic oil on the dynamics of the individual

  10. Analysis of the CO2 emissions and of the other characteristics of the European market of new passenger cars. Part 1. Analysis of general data and analysis per country

    International Nuclear Information System (INIS)

    Zervas, Efthimios

    2010-01-01

    Exhaust CO 2 emitted from passenger cars is one of the major greenhouse effect gases. Several parameters influence the exhaust CO 2 emissions of each passenger car: its characteristics (fuel used, vehicle weight,..) and its use (annual mileage, driving conditions,..). CO 2 emissions from passenger cars decrease during last years; however, this decrease seems to reach its limits. Several parameters of the EU15 new PCs market, such as new passenger cars registrations, type of fuel used, engine capacity, max. power, max. specific power, segment distribution, vehicle weight and their CO 2 emissions on the New European Driving Cycle are analyzed here. The target is to find the real market parameters influencing exhaust CO 2 emissions. Because of the many data used and the parameters examined, this first part of the work is focused on the average values of each parameter studied and the values of each country, while the second part is based on the analysis of each PC segment and the third one on the analysis of the major brands presented in the European market. (author)

  11. The influence of the current intensity on the damping characteristics for a magneto-rheological damper of passenger car

    Science.gov (United States)

    Dobre, A.; Andreescu, C. N.; Stan, C.

    2016-08-01

    Due to their simplicity and controllability, adaptive dampers became very popular in automotive engineering industry, especially in the passenger cars industry, in spite of technological obstacles inherent and the high cost of the magnetic fluid. “MagneRide” is the first technology which uses smart fluids in the shock absorbers of the vehicles adaptive suspensions. Since the discovery of the magneto-rheological effect there is a consistent progress regarding the control algorithms and hardware part itself. These magneto-rheological devices have a major potential which can be explored in various fields of applications. At present many companies make researches for the improvement of the response time and for obtaining a better response at low frequency and amplitude of the body car oscillations. The main objective of this paper is to determine the damping characteristic of a magnetorheological shock absorber of a passenger car. The authors aim to observe how to modify the damping characteristic by changing the intensity of the electric current. The experimental researches have being carried out on a complex and modern test bench especially built for testing shock absorbers, in order to compare the damping characteristic of the classical damper with the magneto-rheological damper.

  12. Well-to-Wheel Analysis of Solar Hydrogen Production and Utilization for Passenger Car Transportation

    Energy Technology Data Exchange (ETDEWEB)

    Felder, R.; Meier, A.

    2006-07-01

    A well-to-wheel analysis is conducted for solar hydrogen production, transport, and usage in future passenger car transportation. Solar hydrogen production methods and selected conventional production Technologies are examined using a life cycle assessment (LCA). Utilization of hydrogen in fuel cells is compared with advanced gasoline and diesel power trains. Solar scenarios show distinctly lower greenhouse gas (GHG) emissions than fossil-based scenarios. For example, using solar hydrogen in fuel cell cars reduces life cycle GHG emissions by 75% compared to advanced fossil fuel power trains and by more than 90% if car and road infrastructure are not considered. Solar hydrogen production allows a reduction of fossil energy requirements by a factor of up to 10 compared to using conventional Technologies. Major environmental impacts are associated with the construction of the steel-intensive infrastructure for solar energy collection due to mineral and fossil resource consumption as well as discharge of pollutants related to today's steel production technology. (Author)

  13. On-road measurement of NH3 emissions from gasoline and diesel passenger cars during real world driving conditions

    Science.gov (United States)

    Suarez-Bertoa, Ricardo; Mendoza-Villafuerte, Pablo; Riccobono, Francesco; Vojtisek, Michal; Pechout, Martin; Perujo, Adolfo; Astorga, Covadonga

    2017-10-01

    NH3 is a precursor of PM2.5 which deteriorates urban air quality, affects human health and impacts the global radiation budget. Since vehicles are important sources of NH3 in urban areas, we have satisfactorily studied the possibility of measuring NH3 emissions from gasoline and SCR-equipped diesel light-duty vehicles during real driving on-road operation using a portable FTIR. The performance of the portable FTIR resulted to be comparable to that of a laboratory-based FTIR during a series of experiments performed in the Vehicle Emission Laboratory (VELA) using the World-harmonized Light-duty Test Cycle (WLTC). Higher on-road NH3 emission factors were obtained for the gasoline vehicle than for the diesel. High NOx emissions were measured from the diesel vehicle, indicating a low efficiency of the DeNOx system, SCR. On-road NH3 emission factors were ∼2 times lower than during the laboratory tests at 23 °C for both vehiclesNH3 emissions were not observed for the diesel vehicle during cold start operation. However, NH3 cold start emissions from the gasoline vehicle were up to 2 orders of magnitude higher than during the entire road trips, ranging from 45 to 134 mg km-1. Cold start emissions are of paramount importance as they commonly take place in urban areas. Hence, future urban reductions in PM2.5 might need to take into consideration the introduction of NH3 emissions limits for passenger cars.

  14. Young drivers and their young passengers.

    NARCIS (Netherlands)

    2015-01-01

    More than one-third of all fatalities among car passengers occurs in the 10-24-year age group. The majority of these young passengers die in a car driven by an 18 to 24-year old. Compared with the composition of the population, these are high proportions, yet the exposure (for example in distance

  15. Car Seat Safety

    Science.gov (United States)

    ... Staying Safe Videos for Educators Search English Español Car Seat Safety KidsHealth / For Parents / Car Seat Safety ... certified child passenger safety technician.) Guidelines for Choosing Car Seats Choose a seat with a label that ...

  16. Improving car passengers' comfort and experience by supporting the use of handheld devices.

    Science.gov (United States)

    van Veen, S A T; Hiemstra-van Mastrigt, S; Kamp, I; Vink, P

    2014-01-01

    There is a demand for interiors to support other activities in a car than controlling the vehicle. Currently, this is the case for the car passengers and--in the future--autonomous driving cars will also facilitate drivers to perform other activities. One of these activities is working with handheld devices. Previous research shows that people experience problems when using handheld devices in a moving vehicle and the use of handheld devices generally causes unwanted neck flexion [Young et al. 2012; Sin and Zu 2011; Gold et al.2011]. In this study, armrests are designed to support the arms when using handheld devices in a driving car in order to decrease neck flexion. Neck flexion was measured by attaching markers on the C7 and tragus. Discomfort was indicated on a body map on a scale 1-10. User experience was evaluated in a semi-structured interview. Neck flexion is significantly decreased by the support of the armrests and approaches a neutral position. Furthermore, overall comfort and comfort in the neck region specifically are significantly increased. Subjects appreciate the body posture facilitated by the armrests and 9 out of 10 prefer using handheld devices with the armrests compared to using handheld devices without the armrests. More efforts are needed to develop the mock-up into an established product, but the angles and dimensions presented in this study could serve as guidelines.

  17. The influence of using LPG device on the CO2 emissions from personal passenger cars

    Directory of Open Access Journals (Sweden)

    Viliam Carach

    2007-12-01

    Full Text Available Traffic, mostly the air and car traffic is the biggest producer of CO2 (51% at present. CO2 is one of the most important greenhouse gases with more than 50 % of emissions contributing to this major global ecological problem. A rising concetration of CO2 in the atmosphere leads to higher global temperatures. The main problem is the rise of CO2 emissions in most developed countries despite international undertakings accepted in 80´s. This is the main reason for finding solutions to reduce the amount of CO2 emissions in the traffic. One of many solutions is the use of LPG fuel. The purpose of this article is to quantify the efficiency of using LPG in personal passenger cars.

  18. Fuel consumption rates of passenger cars in China: Labels versus real-world

    International Nuclear Information System (INIS)

    Huo Hong; Yao Zhiliang; He Kebin; Yu Xin

    2011-01-01

    Recently, China has implemented many policy measures to control the oil demand of on-road vehicles. In 2010, China started to report the fuel consumption rates of light-duty vehicles tested in laboratory and to require new vehicles to show the rates on window labels. In this study, we examined the differences between the test and real-world fuel consumption of Chinese passenger cars by using the data reported by real-world drivers on the internet voluntarily. The sales-weighted average fuel consumption of new cars in China in 2009 was 7.80 L/100 km in laboratory and 9.02 L/100 km in real-world, representing a difference of 15.5%. For the 153 individual car models examined, the real-world fuel consumption rates were -8 to 60% different from the test values. The simulation results of the International Vehicle Emission model show that the real-world driving cycles in 22 selected Chinese cities could result in -8 to 34% of changes in fuel consumption compared to the laboratory driving cycle. Further government effort on fuel consumption estimates adjustment, local driving cycle development, and real-world data accumulation through communication with the public is needed to improve the accuracy of the labeling policy. - Research highlights: → China requires new cars sold to show the test fuel use levels on window labels. → Real-world fuel consumption rates of cars are 15.5% higher than the label values. → Discrepancy between the test cycle and real conditions is a major cause for the gap. → China should adjust the estimates, collect fuel use data, and develop driving cycles. → More official and academic efforts are needed to improve the labeling policy.

  19. Workshop Protocol 5.1 “Developing infrastructure for electric passenger-cars in the corridor between Southern Scandinavia and Germany”

    DEFF Research Database (Denmark)

    Guasco, Clement Nicolas

    and academic institutions. A strategy for the development of infrastructure for electric passenger-cars in the corridor was formed using the “Future Creating” methodology. The workshop was part of the SCANDRIA Action Programme and pointed towards ways for e-mobility in the region. The workshop also provided...

  20. Non-exhaust PM emissions from electric vehicles

    Science.gov (United States)

    Timmers, Victor R. J. H.; Achten, Peter A. J.

    2016-06-01

    Particulate matter (PM) exposure has been linked to adverse health effects by numerous studies. Therefore, governments have been heavily incentivising the market to switch to electric passenger cars in order to reduce air pollution. However, this literature review suggests that electric vehicles may not reduce levels of PM as much as expected, because of their relatively high weight. By analysing the existing literature on non-exhaust emissions of different vehicle categories, this review found that there is a positive relationship between weight and non-exhaust PM emission factors. In addition, electric vehicles (EVs) were found to be 24% heavier than equivalent internal combustion engine vehicles (ICEVs). As a result, total PM10 emissions from EVs were found to be equal to those of modern ICEVs. PM2.5 emissions were only 1-3% lower for EVs compared to modern ICEVs. Therefore, it could be concluded that the increased popularity of electric vehicles will likely not have a great effect on PM levels. Non-exhaust emissions already account for over 90% of PM10 and 85% of PM2.5 emissions from traffic. These proportions will continue to increase as exhaust standards improve and average vehicle weight increases. Future policy should consequently focus on setting standards for non-exhaust emissions and encouraging weight reduction of all vehicles to significantly reduce PM emissions from traffic.

  1. A COMPARATIVE STUDY OF WHOLE-BODY VIBRATION EXPOSURE IN TRAIN AND CAR PASSENGERS: A CASE STUDY IN MALAYSIA

    Directory of Open Access Journals (Sweden)

    M.M. Rahman

    2011-12-01

    Full Text Available Trains and cars are the most important modes of transportation throughout the world. In highly developed countries, trains have become essential for human use as the most well-known form of public transportation, whereas the car plays a significant role in prompt human travel from one place to another. The high magnitude of vibration caused by trains and cars may cause health problems in humans, especially low back pain. The aim of this study was to evaluate and validate the values of daily exposure to vibration A(8 and the vibration dose value (VDV in passengers travelling by train and car and to assess the effects produced by this exposure on the human body. Moreover, this study introduces a newly developed whole-body vibration measurement instrumentation system. One train travelling from the east coast to the south of Malaysia was chosen to conduct the study. Whole-body vibration exposure was measured over 8 hours, which is equal to the duration of normal occupational exposure. One car was chosen randomly and whole-body vibration exposure was measured for 5 min and 10 min. All the data were computed using an IEPE(ICPTM accelerometer sensor connected to a DT9837 device which is capable of effectively measuring and analysing vibration. The vibration results were displayed on a personal computer using a custom graphical user interface (GUI. Matlab software was used to interpret the data. From the results, the whole-body vibration exposure level could be determined. It can be concluded that the whole-body vibration absorbed by the human body is enhanced when the magnitude of the vibration exposure experienced by the passengers increased. This was shown by the increased values of daily exposure to vibration A(8 and VDV calculated in the study.

  2. The effects of studded tires on fatal crashes with passenger cars and the benefits of electronic stability control (ESC) in Swedish winter driving.

    Science.gov (United States)

    Strandroth, Johan; Rizzi, Matteo; Olai, Maria; Lie, Anders; Tingvall, Claes

    2012-03-01

    This study set out to examine the effects of studded tires on fatal crashes on roads covered with ice or snow in Sweden and also to investigate the extra benefits of electronic stability control (ESC) during the winter months. Two different studies are presented in this paper. Both studies used an induced exposure approach. In the main study, 369 in-depth studies of fatal crashes with passenger cars were analyzed to determine whether loss-of-control (LOC) had been a major component or not. Only crashes involving cars without ESC and equipped with approved studded or non-studded winter tires were analyzed. The additional study used police-reported crashes that occurred during the winter seasons 2003-2010, involving passenger cars with and without ESC. While police records in Sweden do not include any tire information, it was assumed that most cars involved in crashes during the winter period would be equipped with studded tires. Findings in the main study showed that in 64% of the fatal crashes on roads covered with ice or snow LOC had been a major component. Furthermore, in 82% of LOC crashes, the passenger car over-steered prior to collision. Studded tires were found to have a statistically significant effect of 42% in terms of fatal crash reduction on roads covered with ice or snow, compared to non-studded winter tires. The effect on dry or wet roads in the winter was negative, although statistically non-significant. In the additional study, it was found that ESC further reduced crashes with injuries by 29%. The benefits on severe and fatal crashes were slightly greater (32%), although the lower 95% confidence limit was lower. Although studded tires were shown to reduce the risk of fatal crash involvement, compared to non-studded winter tires, the proportion of LOC and over-steering among cars with studded tires was large (59% and 49%, respectively). It was therefore concluded that studded tires do not prevent all LOC crashes, while ESC has benefits in those

  3. Chemical composition and source of fine and nanoparticles from recent direct injection gasoline passenger cars: Effects of fuel and ambient temperature

    Science.gov (United States)

    Fushimi, Akihiro; Kondo, Yoshinori; Kobayashi, Shinji; Fujitani, Yuji; Saitoh, Katsumi; Takami, Akinori; Tanabe, Kiyoshi

    2016-01-01

    Particle number, mass, and chemical compositions (i.e., elemental carbon (EC), organic carbon (OC), elements, ions, and organic species) of fine particles emitted from four of the recent direct injection spark ignition (DISI) gasoline passenger cars and a port fuel injection (PFI) gasoline passenger car were measured under Japanese official transient mode (JC08 mode). Total carbon (TC = EC + OC) dominated the particulate mass (90% on average). EC dominated the TC for both hot and cold start conditions. The EC/TC ratios were 0.72 for PFI and 0.88-1.0 (average = 0.92) for DISI vehicles. A size-resolved chemical analysis of a DISI car revealed that the major organic components were the C20-C28 hydrocarbons for both the accumulation-mode particles and nanoparticles. Contribution of engine oil was estimated to be 10-30% for organics and the sum of the measured elements. The remaining major fraction likely originated from gasoline fuel. Therefore, it is suggested that soot (EC) also mainly originated from the gasoline. In experiments using four fuels at three ambient temperatures, the emission factors of particulate mass were consistently higher with regular gasoline than with premium gasoline. This result suggest that the high content of less-volatile compounds in fuel increase particulate emissions. These results suggest that focusing on reducing fuel-derived EC in the production process of new cars would effectively reduce particulate emission from DISI cars.

  4. Determinants of exposure to fine particulate matter (PM 2.5) for waiting passengers at bus stops

    Science.gov (United States)

    Hess, Daniel Baldwin; Ray, Paul David; Stinson, Anne E.; Park, JiYoung

    2010-12-01

    This research evaluates commuter exposure to particulate matter during pre-journey commute segments for passengers waiting at bus stops by investigating 840 min of simultaneous exposure levels, both inside and outside seven bus shelters in Buffalo, New York. A multivariate regression model is used to estimate the relation between exposure to particulate matter (PM 2.5 measured in μg m -3) and three vectors of determinants: time and location, physical setting and placement, and environmental factors. Four determinants have a statistically significant effect on particulate matter: time of day, passengers' waiting location, land use near the bus shelter, and the presence of cigarette smoking at the bus shelter. Model results suggest that exposure to PM 2.5 inside a bus shelter is 2.63 μg m -3 (or 18 percent) higher than exposure outside a bus shelter, perhaps due in part to the presence of cigarette smoking. Morning exposure levels are 6.51 μg m -3 (or 52 percent) higher than afternoon levels. Placement of bus stops can affect exposure to particulate matter for those waiting inside and outside of shelters: air samples at bus shelters located in building canyons have higher particulate matter than bus shelters located near open space.

  5. Influence of diffusion of fuel-efficient motor vehicles on gasoline demand for individual user owned passenger cars

    International Nuclear Information System (INIS)

    Sakaguchi, Takahiro

    2000-01-01

    Trends in the demand for petrol in Japan for cars owned by individuals are discussed with reference to expected improvements in fuel efficiency for new models and the results of a survey of user preferences for fuel-efficient vehicles. Demand for petrol in Japan has continued to increase in line with the number of cars used by individual owners. A questionnaire on motor vehicles sent to households found that, while cost and body style were the primary factors in car purchase, three-quarters of respondents would consider buying a low fuel consumption (LFC) version of the model chosen. The influence of LFC vehicles on future demand for petrol was estimated for up to 2015 by combining market timing with consumer preferences. Comparison of the estimated petrol consumption by LFC cars with the Government's requirement for reduced energy use by the transport sector in order to meet its climate change targets indicated a shortfall and a need to increase consumer demand for LFC vehicles. Government measures to reduce energy use in the transport sector, fuel efficiency targets for 2010, major LFC cars, fuel efficiency improvements by major Japanese motor manufacturers and scenarios for assessing the influence of LFC cars are summarised in five tables. Trends in petrol consumption and estimated use by individual user owned passenger cars are shown graphically

  6. Numerical method for assessing the potential of smart engine thermal management: Application to a medium-upper segment passenger car

    International Nuclear Information System (INIS)

    Caresana, F.; Bilancia, M.; Bartolini, C.M.

    2011-01-01

    Significant reductions in vehicle fuel consumption can be obtained through a greater control of the thermal status of the engine, especially under partial load conditions. Different systems have been proposed to implement this concept, referred to as improved engine thermal management. The amount of fuel saved depends on the components and layout of the engine cooling plant and on the performance of its control system. In this work, a method was developed to calculate the theoretical minimum fuel consumption of a passenger car and used as a reference in comparing different engine cooling system concepts. A high-medium class car was taken as an example and simulated on standard cycles. Models for power train and cooling system components were developed and linked to simulate the vehicle. A preliminary analysis of the engine was performed using AVL's Boost program. The fuel consumption of the complete vehicle, equipped with a conventional cooling plant, was determined on standard cycles and compared with that of a vehicle equipped with a 'perfect' cooling system, to calculate the theoretical reduction in fuel consumption. - Highlights: → We propose a method for assessing the potential of smart engine thermal management. → A conventional cooling system is compared to a 'perfect' one to estimate fuel economy. → We tested the method in an upper-medium segment passenger car.

  7. The emission of BTEX compounds during movement of passenger car in accordance with the NEDC.

    Science.gov (United States)

    Adamović, Dragan; Dorić, Jovan; Vojinović Miloradov, Mirjana; Adamović, Savka; Pap, Sabolč; Radonić, Jelena; Turk Sekulić, Maja

    2018-05-20

    The results of the research in the field of benzene, toluene, ethylbenzene and xylene isomers (BTEX) concentrations in exhaust gases of spark ignition engines under different operating conditions are presented in this paper. The aim of this paper is to gain a clearer insight into the impact of different engine working parameters on the concentrations of BTEX. The experimental investigation has been performed on the SCHENCK 230 W test stand with the controlled IC engine. The engine operating points have been chosen based on the results of a simulation and they are considered as the typical driving conditions according to the New European Driving Cycle. Concentration levels of BTEX compounds in exhaust gas mixtures have been determined by gas chromatography technique by using the combination of Supelcowax 10-Polyethylene glycol column and the PID detector. Based on the experimental research results, the emission model of BTEX compounds has been defined by the simulation of movement of a Fiat Punto Classic passenger car in accordance with the NEDC cycle. Using the results obtained within the simulation, the official statistics on the number of gasoline-powered cars on the territory of the Republic of Serbia and the European Commission data on the annual distance traveled by car, the amounts of BTEX compounds emitted annually per car have been estimated, as well as the emissions of the entire Serbian car fleet. Copyright © 2018 Elsevier B.V. All rights reserved.

  8. EU limits for CO2 emissions of passenger cars. Roads to the 95 g/km target

    Energy Technology Data Exchange (ETDEWEB)

    Smokers, R.; Fraga, F.; Verbeek, M.; Bleuanus, S.; Sharpe, R.; Dekker, D.; Verbeek, R.; Willems, F.; Foster, D. [TNO, Delft (Netherlands); Hill, N.; Norris, J.; Brannigan, C. [AEA Technology plc, London (United Kingdom); Kampman, B.; Den Boer, E.; Van Essen, H. [CE Delft, Delft (Netherlands); Schilling, S.; Gruhlke, A. [Institut fuer Oekologie und Politik Oekopol, Hamburg (Netherlands); Breemersch, T.; De Ceuster, G.; Vanherle, K. [Transport and Mobility Leuven TML, Leuven (Belgium); Wrigley, S.; Owen, N.; Johnson, A. [Ricardo UK, Shoreham-by-Sea, West Sussex (United Kingdom); De Vleesschauwer, T.; Valla, V.; Anand, G. [IHS Global Insight, Nijmegen (Netherlands)

    2012-02-15

    The aim of this project is to support and advise the European Commission on options for lowering of the CO2 limit values of passenger cars and how they can be realised. The following main tasks were performed: (1) state-of-the-art vehicle emission reduction options for 2020; (2) evaluation of other utility parameters in addition to vehicle mass; (3) modalities for achieving 95 g/km; and (4) further aspects, including borrowing and banking of credits, life cycle aspects and rebound aspects.

  9. Comparative Analysis of Passenger Traffic Fleets in Asian Cities: Technology, Driving Activities, and Emission

    Science.gov (United States)

    KIM Oanh, N. T.; Huynh, H. V.; Saikawa, E.

    2015-12-01

    The road transport sector is the major emission source of toxic air pollutants and greenhouse gases (GHGs) in large Asian cities. This paper comparatively analyzed on-road passenger traffic fleets (cars, buses, taxis, motorcycles), using local data collected in cities of Bangkok (BKK), Kathmandu, Hanoi, Ho Chi Minh City (HCMC), and Yangon. Surveys were done in 2010-2014 to obtain information on vehicle technology, driving activities (speed, distance, number, and types of starts), traffic density, and fuel characteristics. Large shares of pre-Euro vehicles were still observed, especially for public buses. The most advanced technology was Euro4, which was observed in small shares (<5%) of the personal car fleets in BKK, HCMC, and Yangon. Euro3 was generally the most advanced technology found in other fleets in these cities. Motorcycles (MC) was the most dominant fleet in all cities, except in Yangon, where they were not allowed. Low vehicle speeds, mainly below 25 km/h, were observed for all vehicle types, indicating traffic jams. Natural gas and LPG had considerable shares in BKK and Yangon while for other cities diesel and gasoline were still the two major fuels used in transportation. Running emission factors (EF) of buses and taxis in Kathmandu were considerably higher than other cities due to its hilly topography, low speeds, high mileage, and less advanced vehicle technologies. The number of passenger vehicles per 1000 people were 400-500 in HCMC and Hanoi (mainly by MC) and in BKK (also by cars), moderate in Kathmandu (200) and the lowest in Yangon (40) because of the MC ban. Annual emissions of the passenger fleets were calculated for each city using the International Vehicle Emission (IVE) for 14 species. BC and OC emissions were estimated using their fractions of PM10 emission. Annual emission per capita of toxic air pollutants and GHGs was analyzed. For example, the emission in kg/year/person for CO, VOC, NOx and PM10 in these cities was 24-150 for CO, 0

  10. Gasoline cars produce more carbonaceous particulate matter than modern filter-equipped diesel cars.

    Science.gov (United States)

    Platt, S M; El Haddad, I; Pieber, S M; Zardini, A A; Suarez-Bertoa, R; Clairotte, M; Daellenbach, K R; Huang, R-J; Slowik, J G; Hellebust, S; Temime-Roussel, B; Marchand, N; de Gouw, J; Jimenez, J L; Hayes, P L; Robinson, A L; Baltensperger, U; Astorga, C; Prévôt, A S H

    2017-07-13

    Carbonaceous particulate matter (PM), comprising black carbon (BC), primary organic aerosol (POA) and secondary organic aerosol (SOA, from atmospheric aging of precursors), is a highly toxic vehicle exhaust component. Therefore, understanding vehicle pollution requires knowledge of both primary emissions, and how these emissions age in the atmosphere. We provide a systematic examination of carbonaceous PM emissions and parameterisation of SOA formation from modern diesel and gasoline cars at different temperatures (22, -7 °C) during controlled laboratory experiments. Carbonaceous PM emission and SOA formation is markedly higher from gasoline than diesel particle filter (DPF) and catalyst-equipped diesel cars, more so at -7 °C, contrasting with nitrogen oxides (NO X ). Higher SOA formation from gasoline cars and primary emission reductions for diesels implies gasoline cars will increasingly dominate vehicular total carbonaceous PM, though older non-DPF-equipped diesels will continue to dominate the primary fraction for some time. Supported by state-of-the-art source apportionment of ambient fossil fuel derived PM, our results show that whether gasoline or diesel cars are more polluting depends on the pollutant in question, i.e. that diesel cars are not necessarily worse polluters than gasoline cars.

  11. Media mix elements affecting brand equity: A study of the Indian passenger car market

    Directory of Open Access Journals (Sweden)

    Tanmay Chattopadhyay

    2010-12-01

    Full Text Available The study develops and empirically tests a model for finding the effect of advertising frequency across different media vehicles towards building brand equity for the passenger car market for first time and repeat buyers. The effect that selected media mix elements had on the dimensions of brand equity was examined. First time buyers are expected to have lower category knowledge than repeat buyers, and are hence expected to behave differently from repeat buyers. Since the knowledge structures of these two groups are expected to be different, it is reasonable to predict that they would process product/brand related information differently and this is corroborated by the results.

  12. Real world CO2 and NOx emissions from 149 Euro 5 and 6 diesel, gasoline and hybrid passenger cars.

    Science.gov (United States)

    O'Driscoll, Rosalind; Stettler, Marc E J; Molden, Nick; Oxley, Tim; ApSimon, Helen M

    2018-04-15

    In this study CO 2 and NO x emissions from 149 Euro 5 and 6 diesel, gasoline and hybrid passenger cars were compared using a Portable Emissions Measurement System (PEMS). The models sampled accounted for 56% of all passenger cars sold in Europe in 2016. We found gasoline vehicles had CO 2 emissions 13-66% higher than diesel. During urban driving, the average CO 2 emission factor was 210.5 (sd. 47) gkm -1 for gasoline and 170.2 (sd. 34) gkm -1 for diesel. Half the gasoline vehicles tested were Gasoline Direct Injection (GDI). Euro 6 GDI engines cars. The average urban NO x emission from Euro 6 diesel vehicles 0.44 (sd. 0.44) gkm -1 was 11 times higher than for gasoline 0.04 (sd. 0.04) gkm -1 . We also analysed two gasoline-electric hybrids which out-performed both gasoline and diesel for NO x and CO 2 . We conclude action is required to mitigate the public health risk created by excessive NO x emissions from modern diesel vehicles. Replacing diesel with gasoline would incur a substantial CO 2 penalty, however greater uptake of hybrid vehicles would likely reduce both CO 2 and NO x emissions. Discrimination of vehicles on the basis of Euro standard is arbitrary and incentives should promote vehicles with the lowest real-world emissions of both NO x and CO 2 . Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Intercity passenger rail : the congress faces critical decisions about the role of and funding for intercity passenger rail systems

    Science.gov (United States)

    2001-07-25

    With the growth in the nation's highway and aviation systems in the : previous decades, intercity passenger rail service lost its competitive edge. Highways have enabled cars to be competitive with conventional passenger trains (those operating up to...

  14. Analysis of Structural and Material Aspects of Selected Elements of a Hydropneumatic Suspension System in a Passenger Car

    Directory of Open Access Journals (Sweden)

    Konieczny Ł.

    2016-03-01

    Full Text Available The article addresses results of analyses of design solutions and materials commonly used in gas springs for hydropneumatic suspension systems. The authors have discussed main advantages resulting from application of such a design solution in passenger car suspension systems. Fundamental correlations defining the parameters characterising a gas spring with constant gas mass have been referred to. Also materials used in the manufacture of selected gas spring elements have been described

  15. Passenger Rail Car Egress -- TRB Workshop

    Science.gov (United States)

    2011-11-01

    The Federal Railroad Administrations (FRA) Office of Railroad Policy and Development is exploring how to enhance regulations that address the safe, timely, and effective emergency evacuation of occupants from passenger rail vehicles in various eme...

  16. Consistent further development of the high pressure diesel fuel injection systems for passenger cars; Konsequente Weiterentwicklung der Hochdruck-Pkw-Dieseleinspritzsysteme

    Energy Technology Data Exchange (ETDEWEB)

    Warga, Johann; Pauer, Thomas; Boecking, Friedrich; Gerhardt, Juergen; Leonhard, Rolf [Robert Bosch GmbH, Stuttgart-Feuerbach (Germany). Diesel Systems

    2011-07-01

    Since the introduction of common rail technology in modern diesel engines for passenger cars there have been many changes and technological revolutions. Solely the continuous increase of the maximum injection pressure has remained unchanged as a guarantee for further engine performance improvement. Whether for down-sizing or for just simply increase the engine power or to reduce CO2 or to improve emissions: In all aspects the injection pressure can offer possible degrees of freedom. Besides, parallel to this continuous increase of injection pressure, the requirements concerning other injection system features have also continuously further developed. This paper focuses on the achievability of EU6 applications, among others, with the new Bosch 2000 bar solenoid valve injector, innovative nozzle technologies as e.g. with improved spray hole geometry or the modular concept common rail pump CP4. Current engine tests with pressures up to 2500 bar prove clearly the further advantages of pressure increase in diesel engines for passenger cars. In addition to the hydraulic components, system approaches in combination with electronic control, sensors and innovative control algorithms are increasingly in focus aiming to improve system accuracy and robustness. (orig.)

  17. The measurement of dynamic radii for passenger car tyre

    Science.gov (United States)

    Anghelache, G.; Moisescu, R.

    2017-10-01

    The tyre dynamic rolling radius is an extremely important parameter for vehicle dynamics, for operation of safety systems as ESP, ABS, TCS, etc., for road vehicle research and development, as well as for validation or as an input parameter of automotive simulations and models. The paper investigates the dynamic rolling radii of passenger car tyre and the influence of rolling speed and inflation pressure on their magnitude. The measurement of dynamic rolling radii has been performed on a chassis dynamometer test rig. The dynamic rolling radii have been measured indirectly, using longitudinal rolling speed and angular velocity of wheel. Due to the subtle effects that the parameters have on rolling radius magnitude, very accurate equipment has to be used. Two different methods have been chosen for measuring the wheel angular velocity: the stroboscopic lamp and the incremental rotary encoder. The paper shows that the stroboscopic lamp has an insufficient resolution, therefore it was no longer used for experimental investigation. The tyre dynamic rolling radii increase with rolling speed and with tyre inflation pressure, but the effect of pressure is more significant. The paper also makes considerations on the viability of simplified formulae from literature for calculating the tyre dynamic rolling radius.

  18. Optimal planning of the Nordic transmission system with 100% electric vehicle penetration of passenger cars by 2050

    International Nuclear Information System (INIS)

    Graabak, Ingeborg; Wu, Qiuwei; Warland, Leif; Liu, Zhaoxi

    2016-01-01

    This paper presents the optimal planning of the Nordic backbone transmission system with 100% electric vehicle penetration of passenger cars by 2050. Electric vehicles will play an important role in the future energy systems and can reduce the greenhouse gas emission from the transport sector. However, the electric vehicles will increase the electricity consumption and might induce congestions in the transmission systems. In order to deal with the electricity consumption increase from the electric vehicle integration into the power system and maximize the social welfare, the optimal investments of the Nordic transmission system are studied. Case studies were conducted using the market simulation model EMPS (Efi's multi-area power market simulator) and two electric vehicle charging scenarios: a spot price based scenario and a dumb charging scenario. The electric vehicle charging power is assumed to be 3.68 kW with 1 phase 16 A. The complete electrification of the private passenger fleet increases the yearly power demand in the Nordic region with ca 7.5%. The profitable increases in transmission capacities are highest for dumb charging, but are very low for both dumb and spot price based charging compared to a Reference case. - Highlights: • The electric vehicle distribution is done using population and car statistics. • The 100% penetration electric vehicle demand is obtained for Nordic countries. • The optimal investments in the Nordic transmission system with electric vehicles are studied.

  19. Reduced PM2.5 in Trujillo, Peru, on El Dia Sin Autos ("The Day Without Cars").

    Science.gov (United States)

    Cassidy, Brandon E; Aguilar-Villalobos, Manuel; Ryan, P Barry; Naeher, Luke P

    2010-01-01

    Street-level and rooftop (three-story building) concentrations of particulate matter Autos ("The Day Without Cars"). The mean 8:00 a.m. to 6:00 p.m. street-level PM2.5 concentration during the motor vehicle ban (21.4 microg/m3; one day) was 49% lower than when vehicles were not impeded (42.2 +/- 7.8 microg/m3--mean +/- 1 standard deviation; 20 days). The rooftop monitoring station indicated a 20% decrease in PM2.5 concentrations (24.8 +/- 2.6 microg/m3 vs. 19.9 +/- 6.0 microg/m3) when motor vehicles were not present within historic downtown Trujillo. Temperature, relative humidity, and wind speed during the motor vehicle ban and during normal traffic were not significantly different (p > .05).

  20. Mobile air quality studies (MAQS in inner cities: particulate matter PM10 levels related to different vehicle driving modes and integration of data into a geographical information program

    Directory of Open Access Journals (Sweden)

    Uibel Stefanie

    2012-10-01

    Full Text Available Abstract Background Particulate matter (PM is assumed to exert a major burden on public health. Most studies that address levels of PM use stationary measure systems. By contrast, only few studies measure PM concentrations under mobile conditions to analyze individual exposure situations. Methods By combining spatial-temporal analysis with a novel vehicle-mounted sensor system, the present Mobile Air Quality Study (MAQS aimed to analyse effects of different driving conditions in a convertible vehicle. PM10 was continuously monitored in a convertible car, driven with roof open, roof closed, but windows open, or windows closed. Results PM10 values inside the car were nearly always higher with open roof than with roof and windows closed, whereas no difference was seen with open or closed windows. During the day PM10 values varied with high values before noon, and occasional high median values or standard deviation values due to individual factors. Vehicle speed in itself did not influence the mean value of PM10; however, at traffic speed (10 – 50 km/h the standard deviation was large. No systematic difference was seen between PM10 values in stationary and mobile cars, nor was any PM10 difference observed between driving within or outside an environmental (low emission zone. Conclusions The present study has shown the feasibility of mobile PM analysis in vehicles. Individual exposure of the occupants varies depending on factors like time of day as well as ventilation of the car; other specific factors are clearly identifiably and may relate to specific PM10 sources. This system may be used to monitor individual exposure ranges and provide recommendations for preventive measurements. Although differences in PM10 levels were found under certain ventilation conditions, these differences are likely not of concern for the safety and health of passengers.

  1. Environmental Performance Evaluation of Ro-Ro Passenger Ferry Transportation

    DEFF Research Database (Denmark)

    Kristensen, Hans Otto Holmegaard; Hagemeister, Constantin

    2012-01-01

    /or emissions per transport unit, is related to the same unit for the different transport forms. For Ro-Ro passenger ferries it can be difficult to find a suitable common transport unit, as they often transport a mix of cargo, such as passengers, passenger cars, trucks, lorries, busses and other rolling...

  2. Roof strength and injury risk in rollover crashes of passenger cars.

    Science.gov (United States)

    Brumbelow, Matthew L; Teoh, Eric R

    2009-12-01

    A 2009 study by the Insurance Institute for Highway Safety found that midsize SUVs with stronger roofs, as measured in quasi-static tests, had lower risk of ejection and lower risk of injury for nonejected drivers. The objective of the present study was to determine whether a similar association exists for other vehicle groups. Twelve small passenger cars were evaluated according to Federal Motor Vehicle Safety Standard 216 test conditions. Crash databases in 14 states provided more than 20,000 single-vehicle rollover crashes involving these vehicles. Logistic regression analyses were used to evaluate the effect of roof strength on the rate of driver injury while assessing and controlling for the effects of driver age, vehicle stability, state, and other factors where necessary. Small cars with stronger roofs had lower overall rates of serious injury, lower rates of ejection, and lower rates of injury for nonejected drivers. Although the effect on ejection was somewhat smaller for cars than for SUVs, the overall pattern of injury results was consistent. For roof strength-to-weight ratio measured within 5 in. (SWR(5)), a one-unit increase (e.g., from 2.0 to 3.0) was associated with a 22 percent reduction in risk of incapacitating or fatal driver injury in single-vehicle rollovers. This compares with a 24 percent reduction estimated for a similar change in roof strength among midsize SUVs. The association between vehicle roof strength and occupant injury risk in rollover crashes appears robust across different vehicle groups and across roof SWR(5) values, varying from just more than 1.5 to just less than 4.0. If roofs were to increase in strength by one SWR(5), a 20-25 percent reduction in risk of serious injury in rollovers would be expected. Still, even if all vehicle roofs were as strong as the strongest roof measured, many rollover injuries still would occur, indicating the need for additional research and countermeasures.

  3. Study of a method for reducing fuel consumption and the amount of specific emissions of harmful substances with exhaust gases of passenger cars when using the “climate control” system

    Science.gov (United States)

    Burakova, L. N.; Anisimov, I. A.; Burakova, A. D.; Burakova, O. D.

    2018-05-01

    The article deals with the issue of improving the fuel economy and environmental friendliness of motor vehicles which serve the administrative and management personnel of the oil and gas industry. It is established that fuel consumption and the amount of specific emissions of harmful substances with exhaust gases of cars when using the “climate control” system depend on the effective ambient temperature, the color of the opaque car body elements, the power of the car engine and the interior volume. However, the simplest controlled factor is the color of the opaque car body elements, which is characterized by the coefficient of light reflection. In the course of experimental studies, we established the dependences of a change in fuel consumption and a share of reducing emissions of harmful substances with exhaust gases of passenger cars with the “climate control” system on the coefficient of light reflection. A method has been developed to reduce fuel consumption and the amount of specific emissions of harmful substances with the exhaust gases of passenger cars using the “climate control” system, which involves painting the vehicle roof white and allows reducing fuel consumption by 5.5-10.3%, and the amount of specific emissions of harmful substances by 0.8-2.3%.

  4. Spatial distribution of particulate matter (PM10 and PM2.5) in Seoul Metropolitan Subway stations.

    Science.gov (United States)

    Kim, Ki Youn; Kim, Yoon Shin; Roh, Young Man; Lee, Cheol Min; Kim, Chi Nyon

    2008-06-15

    The aims of this study are to examine the concentrations of PM10 and PM2.5 in areas within the Seoul Metropolitan Subway network and to provide fundamental data in order to protect respiratory health of subway workers and passengers from air pollutants. A total of 22 subway stations located on lines 1-4 were selected based on subway official's guidance. At these stations both subway worker areas (station offices, rest areas, ticket offices and driver compartments) and passengers areas (station precincts, subway carriages and platforms) were the sites used for measuring the levels of PM. The mean concentrations of PM10 and PM2.5 were relatively higher on platforms, inside subway carriages and in driver compartments than in the other areas monitored. The levels of PM10 and PM2.5 for station precincts and platforms exceeded the 24-h acceptable threshold limits of 150 microg/m3 for PM10 and 35 microg/m3 for PM2.5, which are regulated by the U.S. Environmental Protection Agency (EPA). However, levels measured in station and ticket offices fell below the respective threshold. The mean PM10 and PM2.5 concentrations on platforms located underground were significantly higher than those at ground level (p<0.05).

  5. Child Passenger Safety (A Cup of Health with CDC)

    Centers for Disease Control (CDC) Podcasts

    Proper installation and use of car seats and booster seats for child passengers can save their lives. CDC recommends drivers ensure children are always buckled up. In this podcast, Bethany West discusses how to keep young passengers as safe as possible.

  6. Is passenger vehicle incompatibility still a problem?

    Science.gov (United States)

    Teoh, Eric R; Nolan, Joseph M

    2012-01-01

    Passenger cars often are at a disadvantage when colliding with light trucks (sport utility vehicles [SUVs] and pickups) due to differences in mass, vehicle structural alignment, and stiffness. In 2003, vehicle manufacturers agreed to voluntary measures to improve compatibility, especially in front-to-front and front-to-side crashes, with full adherence to be achieved by September 2009. This study examined whether fatality rates are consistent with the expected benefit of this agreement. Analyses examined 2 death rates for 1- to 4-year-old passenger vehicles during 2000-2001 and 2008-2009 in the United States: occupant deaths per million registered vehicle years in these vehicles and deaths in other cars that collided with these vehicles in 2-vehicle crashes per million registered vehicle years. These rates were computed for each study period and for cars/minivans (referred to as cars), SUVs, and pickups by curb weight (in 500-pound increments). The latter death rate, referred to as the car crash partner death rate, also was computed for front-to-front crashes and front-to-side crashes where the front of the 1- to 4-year-old vehicle struck the side of the partner car. In both study periods, occupant death rates generally decreased for each vehicle type both with increasing curb weight and over time. SUVs experienced the greatest declines compared with cars and pickups. This is due in part to the early fitment of electronic stability control in SUVs, which drastically reduced the incidence of single-vehicle rollover crashes. Pickups had the highest death rates in both study periods. Car crash partner death rates generally declined over time for all vehicle categories but more steeply for SUVs and pickups colliding with cars than for cars colliding with cars. In fact, the car crash partner death rates for SUVs and cars were nearly identical during 2008-2009, suggesting that the voluntary design changes for compatibility have been effective. Car crash partner death

  7. Promotion of energy efficient automobiles via the tax on passenger cars and motorcycles (BPM). A comparative evaluation of different BPM systems

    International Nuclear Information System (INIS)

    Schroten, A.; Blom, M.J.; De Jong, F.L.

    2009-05-01

    The environmental effectiveness of eight different BPM systems (BPM: tax on passenger cars and motorcycles) has been examined for three variants: (1) Basic BPM; (2) BPM systems where basic BPM is combined with a claims bonus/claims penalty system; (3) BPM systems based on absolute CO2 emission. The comparison of different BPM systems consists of (1) providing insight in the financial incentive that various systems provide to consumers to buy a more efficient car, and (2) making an assessment of the CO2 reductions that could be realized in the implementation of the different systems. In both cases the run-down of the BPM system has been taken into account in preparation of the implementation of road pricing. [nl

  8. Development of new products for Europe and individual customer support: Sanden Technical Centre (Europe) GmbH. High-efficiency wind tunnel for passenger car air conditioners at Bad Nauheim; Entwicklung neuer Produkte fuer Europa und individuelle Kundenunterstuetzung: Sanden Technical Centre (Europe) GmbH. Hocheffizienter Klimawindkanal fuer Pkw-Klimaanlagen in Bad Nauheim

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2007-05-15

    As the importance of passenger cars as part of everyday life increased in Japan, Sanden decided that air conditioners for passenger cars would soon be indispensable. Since 1971, Sanden has worked on new technologies in this field, including compact refrigerating compressors. (orig.)

  9. Environmental Analysis of Petrol, Diesel and Electric Passenger Cars in a Belgian Urban Setting

    Directory of Open Access Journals (Sweden)

    Nils Hooftman

    2016-01-01

    Full Text Available The combustion of fossil fuels in the transport sector leads to an aggravation of the air quality along city roads and highways. Urban air quality is a serious problem nowadays as the number of vehicles increases on a yearly basis. With stricter Euro emission regulations, vehicle manufacturers are not meeting the imposed limits and are also disregarding the non-exhaust emissions. This paper highlights the relevance of non-exhaust emissions of passenger vehicles, both conventional (diesel and petrol or electric vehicles (EV, on air quality levels in an urban environment in Belgium. An environmental life cycle assessment was carried out based on a real-world emission model for passenger cars and fuel refinery data. A cut-off was applied to the models to highlight what emissions, both from the refinery to the exhaust and electricity production for EV, do actually occur within Belgium’s borders. Results show that not much progress has been made from Euro 4 to 6 for conventional vehicles. Electric vehicles pose the best alternative solution as a more environmentally friendly means of transportation. The analysis results target policy makers with the intention that regulations and policies would be developed in the future and target the characterization of non-exhaust emissions from vehicles. These results indicate that EVs offer a valid solution for addressing the urban air quality issue and that non-exhaust emissions should be addressed in future regulatory steps as they dominate the impact spectrum.

  10. Differences in passenger car and large truck involved crash frequencies at urban signalized intersections: an exploratory analysis.

    Science.gov (United States)

    Dong, Chunjiao; Clarke, David B; Richards, Stephen H; Huang, Baoshan

    2014-01-01

    The influence of intersection features on safety has been examined extensively because intersections experience a relatively large proportion of motor vehicle conflicts and crashes. Although there are distinct differences between passenger cars and large trucks-size, operating characteristics, dimensions, and weight-modeling crash counts across vehicle types is rarely addressed. This paper develops and presents a multivariate regression model of crash frequencies by collision vehicle type using crash data for urban signalized intersections in Tennessee. In addition, the performance of univariate Poisson-lognormal (UVPLN), multivariate Poisson (MVP), and multivariate Poisson-lognormal (MVPLN) regression models in establishing the relationship between crashes, traffic factors, and geometric design of roadway intersections is investigated. Bayesian methods are used to estimate the unknown parameters of these models. The evaluation results suggest that the MVPLN model possesses most of the desirable statistical properties in developing the relationships. Compared to the UVPLN and MVP models, the MVPLN model better identifies significant factors and predicts crash frequencies. The findings suggest that traffic volume, truck percentage, lighting condition, and intersection angle significantly affect intersection safety. Important differences in car, car-truck, and truck crash frequencies with respect to various risk factors were found to exist between models. The paper provides some new or more comprehensive observations that have not been covered in previous studies. Copyright © 2013 Elsevier Ltd. All rights reserved.

  11. Development process of new bumper beam for passenger car: A review

    International Nuclear Information System (INIS)

    Davoodi, M.M.; Sapuan, S.M.; Aidy, A.; Abu Osman, N.A.; Oshkour, A.A.; Wan Abas, W.A.B.

    2012-01-01

    Highlights: ► The process of new bumper beam development for passenger car is discussed. ► A new bumper system has been added to the previous developed bumper systems. ► The flow chart of design and analysis of bumper beam is shown. ► Different analysis for developing new bumper beam before production is discussed. ► The process of material selection in bumper beam is discussed. -- Abstract: Bumper beam absorbs the accidental kinetic energy by deflection in low-speed impact and by deformation in high-speed impact. The safety regulations “low-, and high-speed, and pedestrian impacts” along with new environmental restrictions “end-of-life vehicles” increased the complexity level of bumper system design. The new bumper design must be flexible enough to reduce the passenger and occupant injury and stay intact in low-speed impact besides being stiff enough to dissipate the kinetic energy in high-speed impact. The reinforcement beam plays a vital role in safety and it must be validated through finite-element analysis (FEA) and experimental tests before mass production. The careful design and analysis of bumper beam effective parameters can optimize the strength, reduce the weight, and increase the possibility of utilizing biodegradable and recyclable materials to reduce the environmental pollution. Developing the correct design and analysis procedures prevents design re-modification. On the other hand, analysis of the most effective parameters conducive to high bumper beam strength increases the efficiency of product development. Cross section, longitudinal curvature, fixing method, rib thickness, and strength are some of the significant design parameters in bumper beam production. This study critically reviews the related literature on bumper design to come up with the optimal bumper beam design process. It particularly focuses on the effective parameters in the design of bumper beam and their most suitable values or ranges of values. The results can

  12. Investigation of Gas Piston Actuated Opening-Closing Trunk Lid Mechanisms Used in Passenger Cars

    Directory of Open Access Journals (Sweden)

    Ahmet YILDIZ

    2015-05-01

    Full Text Available In this study, the gas piston actuated opening-closing trunk lid mechanisms used in passenger cars are investigated theoretically and experimentally. First, the position analysis of the mechanism which is a four-bar linkage has been carried out. Then the quasi-static analyzes according to the principle of virtual work have been made, and so the hand force, one of the most important parameters in terms of ergonomics, required for opening and closing the trunk lid has been calculated. In order to verify this developed model, the hand force has been determined also experimentally, performing the physical tests on an existing vehicle at Turkish Automobile Factory Inc. (TOFAŞ. Eventually, it is observed that the results obtained from mathematical model and the experimental measurements are compatible each other. This established model will provide convenience for manufacturers to determine the hand force for different model of vehicles. 

  13. Sustainable passenger road transport scenarios to reduce fuel consumption, air pollutants and GHG (greenhouse gas) emissions in the Mexico City Metropolitan Area

    International Nuclear Information System (INIS)

    Chavez-Baeza, Carlos; Sheinbaum-Pardo, Claudia

    2014-01-01

    This paper presents passenger road transport scenarios that may assist the MCMA (Mexico City Metropolitan Area) in achieving lower emissions in both criteria air pollutants (CO, NO x , NMVOC (non-methane volatile organic compounds), and PM 10 ) and GHG (greenhouse gas) (CH 4 , N 2 O and CO 2 ), while also promoting better mobility and quality of life in this region. We developed a bottom-up model to estimate the historical trends of energy demand, criteria air pollutants and GHG emissions caused by passenger vehicles circulating in the Mexico City Metropolitan Area (MCMA) in order to construct a baseline scenario and two mitigation scenarios that project their impact to 2028. Mitigation scenario “eff” considers increasing fuel efficiencies and introducing new technologies for vehicle emission controls. Mitigation scenario “BRT” considers a modal shift from private car trips to a Bus Rapid Transport system. Our results show significant reductions in air pollutants and GHG emissions. Incentives and environmental regulations are needed to enable these scenarios. - Highlights: • More than 4.2 million passenger vehicles in the MCMA (Mexico City Metropolitan Area) that represent 61% of criteria pollutants and 44% of GHG (greenhouse gas) emissions. • Emissions of CO, NO x and NMVOC (non-methane volatile organic compounds) in baseline scenario decrease with respect to its 2008 value because emission standards. • Emissions of PM 10 and GHG increase in baseline scenario. • Emissions of PM 10 and GHG decrease in eff + BRT scenario from year 2020. • Additional reductions are possible with better standards for diesel vehicles and other technologies

  14. Children's and Adults' Comfort Experience of Extra Seat Belts When Riding in the Rear Seat of a Passenger Car.

    Science.gov (United States)

    Osvalder, Anna-Lisa; Hansson, Ida; Bohman, Katarina

    2015-01-01

    The objective of this study was to explore passengers' comfort experience of extra seat belts during on-road driving in the rear seat of a passenger car and to investigate how the use of extra belts affects children's and adults' attitudes to the product. Two different seat belt systems were tested, criss-cross (CC) and backpack (BP), consisting of the standard 3-point belt together with an additional 2-point belt. In total, 32 participants (15 children aged 6-10, 6 youths aged 11-15, and 11 adults aged 20-79, who differed considerably in size, shape, and proportions) traveled for one hour with each system, including city traffic and highway driving. Four video cameras monitored the test subject during the drive. Subjective data regarding emotions and perceived discomfort were collected in questionnaires every 20 min. A semistructured interview was held afterwards. All participant groups accepted the new products and especially the increased feeling of safety (P car. CC was appreciated for its symmetry, comfort, and the perceived feeling of safety. Some participants found CC unpleasant because the belts tended to slip close to the neck, described as a strangling feeling. BP was simpler to use and did not cause annoyance to the neck in the way CC did. Instead, it felt asymmetric and to some extent less safe than CC. Body size and shape affected seat belt fit to a great extent, which in turn affected the experience of comfort, both initially and over time. Perceived safety benefit and experienced comfort were the most determinant factors for the attitude toward the extra seat belts. The extra seat belts were perceived as being better than the participants had expected before the test, and they became more used to them over time. This exploratory study provided valuable knowledge from a user perspective for further development of new seat belt systems in cars. In addition to an increased feeling of safety, seat belt fit and comfort are supplementary influencing

  15. Passenger car equivalents of becak bermotor at road segment in Medan

    Science.gov (United States)

    Surbakti, M. S.; Sembiring, I.

    2018-02-01

    The road traffic systems, travel patterns and other traffic characteristics are different for each country due to differences in the geometric patterns, available transport facilities for commuters, proportional and type of the vehicle itself and so on. In Indonesia, the standard of pce (Passenger Car Equivalent) value found on IHCM (Indonesian Highway Capacity Manual) published in 1997. IHCM stated that the value of pce for heavy vehicles and motorcycles are 1.3 and 0.5 respectively. On these day, regarding Medan as a third biggest city in Indonesia, there have been lot of changes with regarding to the composition of the vehicle, as well as variations of the type of the vehicle itself. Becak bermotor (motorized tricycles) is a vehicle which is widely available in the city of Medan. Data from Medan City Transportation Department stated that there are more than 20,000 motorized motorized tricycles vehicles operating in the city at these day. Pce value of these rickshaws will be calculated based on observations at road and intersections in Medan. The calculation result shows that the pce value of motorized rickshaw is more than 1. This value will make the calculations regarding the performance of the traffic can be performed more accurately.

  16. From laboratory to road: Modeling the divergence between official and real-world fuel consumption and CO_2 emission values in the German passenger car market for the years 2001–2014

    International Nuclear Information System (INIS)

    Tietge, Uwe; Mock, Peter; Franco, Vicente; Zacharof, Nikiforos

    2017-01-01

    Official fuel consumption and carbon dioxide (CO_2) emission values of European passenger cars are widely recognized to be unrepresentative of real-world driving. The divergence between official and real-world values undermines national vehicle taxation schemes and EU-wide CO_2 standards for passenger cars, particularly since the divergence increases with new model generations. This study examines real-world fuel consumption data from more than 130,000 vehicles to investigate the development of the divergence. The analysis validates and refines a regression model developed by , which estimates real-world fuel consumption of cars based on readily available vehicle characteristics, namely official fuel consumption values, vehicle mass, and engine capacity. The regression model yielded coefficients of determination of 0.87 or higher, but was found to underestimate fuel consumption of newer vehicles and company cars. This study proposes to add vehicle build year as a regressor to account for the increasing divergence between official and real-world fuel consumption figures. - Highlights: • Real-world fuel consumption of new cars in Germany is 36% higher than official values. • The divergence between official and real-world fuel consumption has grown over time. • A simple regression accounts for ≥87% of the variance in real-world fuel consumption values. • Vehicle age must be included in the model to account for the growing divergence.

  17. Crippling test of a Budd Pioneer passenger car

    Science.gov (United States)

    2012-04-16

    This research program was sponsored by the Federal Railroad Administration (FRA) Office of Research and Development in support of the advancement of improved safety standards for passenger rail vehicles. FRA and the Volpe National Transportation Syst...

  18. Trends in passenger transport energy use in South Korea

    International Nuclear Information System (INIS)

    Eom, Jiyong; Schipper, Lee

    2010-01-01

    Having a clear understanding of transport energy use trends is crucial to identifying opportunities and challenges for efficient energy use for the transport sector. To this date, however, no detailed analysis has been conducted with regard to rapidly growing passenger transport energy use in South Korea. Using bottom-up data developed from a variety of recent sources, we described the trends of transport activity, energy use, and CO 2 emissions from South Korea's transport sector since 1986 with a particular focus on its passenger transport. By decomposing the trends in passenger transport energy use into activity, modal structure, and energy intensity, we showed that while travel activity has been the major driver of the increase in passenger transport energy use in South Korea, the increase was to some extent offset by the recent favorable structural shift toward bus travel and away from car travel. We also demonstrated that while bus travel has become less energy intensive since the Asian Financial Crisis, car travel has become increasingly energy intensive.

  19. Model-based design of active vibration compensation in the passenger car powertrain; Modellbasierte Auslegung der aktiven Schwingungskompensation im Kfz-Antriebsstrang

    Energy Technology Data Exchange (ETDEWEB)

    Quernheim, L.

    2008-07-01

    Modern passenger cars have increasingly higher driving torques while the rotary mass of the powertrain is reduced. This induces vibrations. Especially during load change operations, the driving comfort may therefore be impaired by jolting. To reduce these vibrations, the engine control unit has integrated control functions that influence the driving characteristics. Until now, these control functions were adjusted empirically by the application engineer during time-consuming test drives, but this option is failing as development times are getting shorter while there are increasing numbers of car lines. The author therefore presents a new option, i.e. optimisation of the comfort functions by means of model-based control unit design. The example of an active vibration damper is presented to illustrate this model-based procedure, and vehicle analyses were carried out with the intention to show that this method supports the application engineer in his work efficiently. (orig.)

  20. Potential environmental impact of bioethanol production chain from fiber sorghum to be used in passenger cars.

    Science.gov (United States)

    Forte, Annachiara; Zucaro, Amalia; Fagnano, Massimo; Fierro, Angelo

    2017-11-15

    A life cycle assessment (LCA) was applied to assess the environmental load of a prospective local bioethanol (EtOH) production system in Southern Italy by using lignocellulosic Fiber sorghum (FS) feedstock. A two steps analysis was carried out considering: (i) a "cradle-to-farm gate" LCA to investigate thoroughly the FS cultivation on hilly marginal land and (ii) a "cradle-to-wheels" system boundary encompassing the environmental pressure of the whole EtOH supply-use chain. Primary data related to lignocellulosic biomass production were combined with experimental feedstock conversion processes through advanced second generation technology. The purpose was the evaluation of the environmental performance of different EtOH-gasoline mixtures in midsize passenger cars: E10 (10% of EtOH and 90% of gasoline) and E85 (85% of EtOH and 15% of gasoline). N fertilization appeared as the prevailing contributor of the crop phase. The "cradle-to-wheels" results concerning E10 passenger car disclosed that the main hotspots were represented by the input of low sulphur petrol (66%) and the linked tailpipe emissions (15%), for almost all the impact categories. Otherwise, for E85 flex-fuel vehicle, the major drivers were represented by the feedstock production (46%) and the imported electricity used in the conversion facility (18%). The FS EtOH blends entailed potential environmental benefits compared with the fossil counterpart (gasoline) for climate change, ozone and fossil depletions. Otherwise, they evidenced a worse profile in terms of acidification, eutrophication and particulate matter formation. Within the context of a the prospective territorial bio-refinery network, the comparison of the annual FS bioethanol based systems with similar EtOH scenarios from giant reed perennial crops highlighted: (i) the importance to optimize the N-management for FS feedstock cultivation and (ii) the need to increase the use of the renewable energy carriers along the industrial conversion

  1. Occupant Volume Integrity Evaluation in Passenger Rail Cars

    Science.gov (United States)

    2012-02-01

    This research, which is intended to enable the growth of high-speed and intercity passenger rail transportation, was sponsored by the Federal Railroad Administration (FRA) Office of Research and Development, as part of the train Occupant Protection r...

  2. Child Passenger Safety (A Cup of Health with CDC)

    Centers for Disease Control (CDC) Podcasts

    2016-09-29

    Proper installation and use of car seats and booster seats for child passengers can save their lives. CDC recommends drivers ensure children are always buckled up. In this podcast, Bethany West discusses how to keep young passengers as safe as possible.  Created: 9/29/2016 by MMWR.   Date Released: 9/29/2016.

  3. Particulate matter urban air pollution from traffic car

    Science.gov (United States)

    Filip, G. M.; Brezoczki, V. M.

    2017-05-01

    The particulate matters (PM) are very important compounds of urban air pollution. There are a lot of air pollution sources who can generate PM and one of the most important of them it is urban traffic car. Air particulate matters have a major influence on human health so everywhere are looking for PM reducing solutions. It is knows that one of the solution for reduce the PM content from car traffic on ambient urban air is the fluidity of urban traffic car by introduction the roundabout intersections. This paper want to present some particulate matter determinations for PM10 and PM2.5 conducted on the two types of urban intersection respectively traffic light and roundabout intersections in Baia Mare town in the approximate the same work conditions. The determinations were carried out using a portable particulate matter monitor Haz - Dust model EPAM - 5000, who can provide a real time data for PM10, PM 2.5.Determinations put out that there are differences between the two locations regarding the PM content on ambient air. On roundabout intersection the PM content is less than traffic light intersection for both PM10 and PM 2.5 with more than 30%.

  4. High Speed Vessels to Market : Comparative Case Studies in the Passenger Trade

    Science.gov (United States)

    2001-08-01

    The Volpe Center chose to study several existing catamarans and high speed monohulls in comparison to representative SWATH family craft, including the SLICE 400 (passenger) and SLICE 600 (passenger/90 car) variants, the former similar in size and per...

  5. Flexible injection control for fuel consumption and emission reduction in passenger cars?; Flexible Einspritzverlaufsformung: Auch bei PKW-Dieselmotoren ein wirkungsvolles Mittel zur Reduzierung von Verbrauch und Schadstoffemissionen?

    Energy Technology Data Exchange (ETDEWEB)

    Laumen, H.J.; Koerfer, T.; Lamping, M. [FEV Motorentechnik GmbH, Aachen (Germany); Pischinger, S.; Schmuecker, K.J. [RWTH Aachen (Germany). Lehrstuhl fuer Verbrennungskraftmaschinen

    2007-07-01

    In the recent decade the Diesel injection technology has been modified significantly. The old cam driven injection systems have been replaced nearly completely by modern Common Rail systems which enable a significantly higher degree of freedom especially with respect to multi-injection strategies and exhaust aftertreatment demands. Nevertheless, cam driven injection systems offered special characteristics which were favorable regarding fuel consumption and emissions. Due to the much higher nozzle opening and closing velocity, the seat throttling effects are widely reduced. Furthermore the fuel injection rate during ignition delay is smaller, compared to today's Common Rail systems. A new type of a piezoelectric Common Rail injector for passenger car engines, called FIRST (Flexible Injection Rate Shaping Tool) is described in this article, which combines both, the flexibility of modern Common Rail injectors as well as the benefits of cam driven injection systems regarding reduced seat throttling effects. Additionally flexible injection rate shaping is enabled by forming the slope of the actuator voltage. Both, the hydraulic behavior and also the engine performance with the new injector are presented in comparison to conventional injectors. The FIRST injector offers a benefit of 20% in PM and CO emission with constant NO{sub x} emission and reduced fuel consumption at part load as a result of the reduced seat throttling. By an optimization of the injection rate shape, the NO{sub x} emissions can be reduced by 40% at constant fuel consumption and PM emissions and without deterioration of NVH level. (orig.)

  6. [MICROCLIMATE CONDITION IN SUBWAY CARS IN THE SUMMER PERIOD OF THE YEAR].

    Science.gov (United States)

    Leksin, A G; Evlampieva, M N; Timoshenkova, E V; Morgunov, A V; Kaptsov, V A

    2015-01-01

    There are presented the results of the work, which aims to identify the relationship between the temperature of air in the salons of subway cars from the heat output of passengers in different people occupancy of cars during "peak hours", and to determine the efficacy offorced air handling regular ventilation or air conditioning system to remove the elevated heat load on passengers. In the work there was used the method of calculating the amount of heat output of 215 passengers (nominal fullness of the chamber) and the simulation method of heat and moisture output of the same number of passengers. The operating system of ventilation has been shown to fail to decline the average temperature of the air in the passenger compartment to the optimum values and most efficient approach for the reducing the heat load on the passengers is the use of air conditioning systems.

  7. Transient thermal model of passenger car's cabin and implementation to saturation cycle with alternative working fluids

    International Nuclear Information System (INIS)

    Lee, Hoseong; Hwang, Yunho; Song, Ilguk; Jang, Kilsang

    2015-01-01

    A transient thermal model of a passenger car's cabin is developed to investigate the dynamic behavior of cabin thermal conditions. The model is developed based on a lumped-parameter model and solved using integral methods. Solar radiation, engine heat through the firewall, and engine heat to the air ducts are all considered. Using the thermal model, transient temperature profiles of the interior mass and cabin air are obtained. This model is used to investigate the transient behavior of the cabin under various operating conditions: the recirculation mode in the idling state, the fresh air mode in the idling state, the recirculation mode in the driving state, and fresh air mode in the driving state. The developed model is validated by comparing with experimental data and is within 5% of deviation. The validated model is then applied for evaluating the mobile air conditioning system's design. The study found that a saturation cycle concept (four-stage cycle with two-phase refrigerant injection) could improve the system efficiency by 23.9% and reduce the power consumption by 19.3%. Lastly, several alternative refrigerants are applied and their performance is discussed. When the saturation cycle concept is applied, R1234yf MAC (mobile air conditioning) shows the largest COP (coefficient of performance) improvement and power consumption reduction. - Highlights: • The transient thermal model of the passenger car cabin is developed. • The developed model is validated with experimental data and showed 5% deviation. • Saturation cycle concept is applied to the developed cabin model. • There is 24% COP improvement by applying the saturation cycle concept. • R1234yf showed the highest potential when it is applied to the saturation cycle.

  8. Computational Fluid Dynamic Analysis of Enhancing Passenger Cabin Comfort Using PCM

    Science.gov (United States)

    Purusothaman, M.; Valarmathi, T. N.; Dada Mohammad, S. K.

    2016-09-01

    The main purpose of this study is to determine a cost effective way to enhance passenger cabin comfort by analyzing the effect of solar radiation of a open parked vehicle, which is exposed to constant solar radiation on a hot and sunny day. Maximum heat accumulation occurs in the car cabin due to the solar radiation. By means of computational fluid dynamics (CFD) analysis, a simulation process is conducted for the thermal regulation of the passenger cabin using a layer of phase change material (PCM) on the roof structure of a stationary car when exposed to ambient temperature on a hot sunny day. The heat energy accumulated in the passenger cabin is absorbed by a layer of PCM for phase change process. The installation of a ventilation system which uses an exhaust fan to create a natural convection scenario in the cabin is also considered to enhance passenger comfort along with PCM.

  9. 49 CFR 238.413 - End structures of trailer cars.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false End structures of trailer cars. 238.413 Section... II Passenger Equipment § 238.413 End structures of trailer cars. (a) Except as provided in paragraph (b) of this section, the end structure of a trailer car shall be designed to include the following...

  10. A comparison of personal exposure to air pollutants in different travel modes on national highways in India.

    Science.gov (United States)

    Kolluru, Soma Sekhara Rao; Patra, Aditya Kumar; Sahu, Satya Prakash

    2018-04-01

    People often travel a long distance on highways to the nearest city for professional/business activities. However, relatively few publications on passenger exposure to pollutants on highways in India or elsewhere are available. The aim of this study was to examine the contribution of different travel modes to passengers' pollutant exposure for a long distance travel on a national highway in India. We measured PM 2.5 and CO exposure levels of the passengers over 200km on a national highway using two portable air monitors, EVM-7 and EPAM-5000. Personal concentration exposures and per min-, per hour-, per trip- and round trip mass exposures for three travel modes were calculated for 9 trips. Association between pollutants and weather variables were evaluated using levels Spearman correlation. ANOVA was carried out to evaluate the influence of travel mode, the timing of trips, temperature and RH on personal exposures. On an average, PM 2.5 personal concentration exposure levels were highest in the car (85.41±61.85μgm -3 ), followed by the bus (75.08±55.39μgm -3 ) and lowest in the car (ac) (54.43±34.09μgm -3 ). In contrast, CO personal exposure was highest in the car (ac) (1.81±1.3ppm). Travel mode explained the highest variability for CO (18.1%), CO 2 (9.9%), PM 2.5 (1.2%) exposures. In-city mass exposures were higher than trip averages; PM 2.5 :1.21-1.22, 1.13-1.19 and 1.03-1.28 times; CO: 1.20-1.57, 1.37-2.10 and 1.76-2.22 times for bus, car and car (ac) respectively. Traveling by car (ac) results in the lowest PM 2.5 exposures, although it exposes the passenger to high CO level. Avoiding national highways passing through cities can reduce up to 25% PM 2.5 and 50% CO mass exposures. This information can be useful for increasing environmental awareness among the passengers and for framing better pollution control strategies on highways. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Energy consumption and environmental effects of passenger transport modes. A life cycle study on passenger transport modes

    International Nuclear Information System (INIS)

    Kalenoja, H.

    1996-01-01

    Energy consumption and environmental effects of different passenger transport modes vary on the different stages of the fuel chain and during the production and maintenance of vehicles and infrastructure. Energy consumption and the environmental effects calculated per passenger mileage depend strongly on the vehicle occupancy. The properties of transport modes on urban areas and on the long distance transport have been evaluated in this study. The energy consumption and environmental effects calculated per passenger mileage have been assessed for passenger car, bus, tram, train, airplane and ferry. The emissions have been evaluated during the whole fuel chain. In this study only the airborne emissions have been taken into account. In the energy consumption calculations the energy content of vehicles and the infrastructure, energy consumption during the fuel chain and during the end use have been taken into consideration. (au)

  12. Safer passenger car front shapes for pedestrians: A computational approach to reduce overall pedestrian injury risk in realistic impact scenarios.

    Science.gov (United States)

    Li, Guibing; Yang, Jikuang; Simms, Ciaran

    2017-03-01

    Vehicle front shape has a significant influence on pedestrian injuries and the optimal design for overall pedestrian protection remains an elusive goal, especially considering the variability of vehicle-to-pedestrian accident scenarios. Therefore this study aims to develop and evaluate an efficient framework for vehicle front shape optimization for pedestrian protection accounting for the broad range of real world impact scenarios and their distributions in recent accident data. Firstly, a framework for vehicle front shape optimization for pedestrian protection was developed based on coupling of multi-body simulations and a genetic algorithm. This framework was then applied for optimizing passenger car front shape for pedestrian protection, and its predictions were evaluated using accident data and kinematic analyses. The results indicate that the optimization shows a good convergence and predictions of the optimization framework are corroborated when compared to the available accident data, and the optimization framework can distinguish 'good' and 'poor' vehicle front shapes for pedestrian safety. Thus, it is feasible and reliable to use the optimization framework for vehicle front shape optimization for reducing overall pedestrian injury risk. The results also show the importance of considering the broad range of impact scenarios in vehicle front shape optimization. A safe passenger car for overall pedestrian protection should have a wide and flat bumper (covering pedestrians' legs from the lower leg up to the shaft of the upper leg with generally even contacts), a bonnet leading edge height around 750mm, a short bonnet (17° or car front shape for head and leg protection are generally consistent, but partially conflict with pelvis protection. In particular, both head and leg injury risk increase with increasing bumper lower height and depth, and decrease with increasing bonnet leading edge height, while pelvis injury risk increases with increasing bonnet leading

  13. National car and customer loyalty: the Malaysian perspective

    OpenAIRE

    Md Isa, Mohd Azwardi

    2017-01-01

    The ASEAN Free Trade Agreement has facilitated the entrance of foreign cars into Malaysia’s passenger car market and consequently imported cars are posing a serious threat to domestic automotive companies. This can be seen by decreasing sales figures and the deteriorating market share for the Proton and Perodua (companies partly-owned by government). Driven by this situation, this study examines customer satisfaction and loyalty for the consumers who have purchased these cars. ...

  14. Fuel consumption of business passenger cars and plug-in vehicles; Praktijkverbruik van zakelijke personenauto's en plug-in voertuigen

    Energy Technology Data Exchange (ETDEWEB)

    Ligterink, N.E.; Smokers, R.T.M.

    2013-05-15

    TNO investigates the use and fuel consumption of private cars since 2008. In this report the results for 2012 are presented. In part 1 the most recent results of statistical analyses of fuel card data, which are used by business-type drivers of passenger cars, are presented. The second part contains the results of an analysis of available fuel consumption data of so-called plug-in hybrid electric vehicles and range-extender electric vehicles that have entered the market in 2012 [Dutch] TNO doet al sinds 2008 onderzoek naar het praktijkverbruik van personenauto's. In dit rapport worden de resultaten over 2012 weergegeven. Het eerste deel presenteert de meest recente resultaten van statistische analyses van tankpasdata van door zakelijke rijders gebruikte personenvoertuigen. Het tweede deel bevat de resultaten van een analyse van beschikbare verbruiksgegevens van zogenoemde 'plug-in hybrides' en 'range-extender' elektrische voertuigen die in 2012 op de markt zijn gekomen.

  15. Air quality inside passenger cars

    Directory of Open Access Journals (Sweden)

    Joanna Faber

    2017-02-01

    Full Text Available Vehicle interior is a specific environment of relatively small volume, with variety of materials placed inside, including hard and soft plastics, adhesives, paints, lubricants and many others. As a result, particularly in case of newly produced vehicles, large amounts and numbers of volatile species, especially volatile organic compounds (VOCs, may be emitted and have influence vehicle interior air quality (VIAQ. Despite the fact that many of these compounds may not be harmful for human health, some of them may be toxic, and this is the reason for increasing concern of vehicle manufacturers and users recently. The level of contamination varies from one vehicle to another and may be influenced by atmospheric conditions, external pollution, user habits, quality of materials used and others. The main aim of this paper was to present current knowledge status on VIAQ, with indication of main air pollutants and their concentrations. Vehicle interior air quality is discussed on the basis of studies on new and used cars in different conditions and locations. Main sources of VOCs presence inside car cabin are discussed in this paper with additional information regarding materials emissions. Differences in sampling and analytical methodologies were not debated, however, since the results differs largely in the scope of both number and amount of VOCs, a need of testing methods harmonization is indicated. Presented data may be helpful for legislative requirements introduction.

  16. Configurations of hybrid-electric cars propulsion systems

    OpenAIRE

    Cundev, Dobri; Sarac, Vasilija; Stefanov, Goce

    2011-01-01

    Over the last few years, hybrid electric cars have taken significant role in automotive market. There are successful technological solutions of hybrid-electric propulsion systems implemented in commercial passenger cars. Every automobile manufacturer of hybrid vehicles has unique hybrid propulsion system. In this paper, all implemented systems are described, analyzed and compared.

  17. The principal-agent problem and transport energy use: Case study of company lease cars in the Netherlands

    International Nuclear Information System (INIS)

    Graus, Wina; Worrell, Ernst

    2008-01-01

    Barriers exist for improvement of energy efficiency, of which the principal-agent problem is considered an important one. The principal-agent problem is a potential barrier for energy policies based on economic instruments, as the decision maker may be partially insulated from the price signal given by such policies. We estimate the size and the impact of the principal-agent problem for cars provided by companies as a benefit to employees in the Netherlands. Of all passenger cars in the Netherlands, 11% is classified as company cars, which consume 21% of the total energy consumption by passenger cars. As company cars are newer, operate more diesel engines, but are also larger, the fuel efficiency is slightly worse than that of private cars. Company cars seem to drive longer distances for commuting than the national average of private cars. Together, this might result in a net 1-7% increase of all fuel use of passenger cars in the Netherlands. This indicates that there is potential to reduce energy consumption of company cars and a need for policies aimed at improving energy efficiency of company cars

  18. Predicting passenger car window buffeting with transient external-aerodynamics simulations

    International Nuclear Information System (INIS)

    Sovani, S.D.; Hendriana, D.

    2002-01-01

    A transient CFD analysis of air flow past a passenger car is presented. The aim of the work is to predict buffeting frequencies and sound pressure levels (SPL) experienced by the driver and co-driver when the front left window of the vehicle is open. Two vehicle road speeds (40 and 60 mph), and 3 yaw angles (0, 5, and 10 degrees) are considered. Buffeting frequency spectrums obtained from transient CFD simulations are presented for each case along with similar experimentally obtained spectrums. The commercial CFD code FLUENT5.6 was used for the simulations. RNG k-e and LES turbulence models were tested. Experimental measurements indicate that the first predominant buffeting frequency peak occurs at 17 Hz when the vehicle is traveling at 60 mph and 0 o yaw. The SPL is 116 dB at this peak. Increasing the yaw angle to 5 o causes no change in the frequency of the first peak but the SPL rises to 128 dB. A further increase in yaw angle to 10 o leaves the frequency of the first peak unaltered, but increases the SPL to 130 dB. When the vehicle speed is reduced from 60 to 40 mph at 0 o yaw, the first predominant peak shifts to 105dB at 15 Hz. In most cases the frequencies obtained from the CFD analysis are found to be off from the experimental measurements by a maximum of 5.9% and the SPLs by a maximum of 6.9%. (author)

  19. PASSENGER CAR EQUIVALENT (PCE OF THROUGH VEHICLES AT SIGNALIZED INTERSECTIONS IN DHAKA METROPOLITAN CITY, BANGLADESH

    Directory of Open Access Journals (Sweden)

    Partha SAHA

    2009-01-01

    PCE currently used in Bangladesh is based on the values given in Geometric Design of Highways (MoC, 2001, which is the modification of the values given by Webster (1958 on the study performed in the United Kingdom in the 50's and 60's. But now-a-days, the situation is far different both for traffic and road user as the characteristics have changed from that time. Hence, in this paper an empirical study was carried out to determine the PCE of different types of vehicle that reflect the actual traffic conditions of Dhaka Metropolitan City. Data were collected from ten signalized intersections and the headway ratio method was used to estimate the PCE of different types of vehicle. The main vehicle compositions observed during the study period consist of passenger cars, auto-rickshaws, mini-buses and buses. The PCE obtained in this study were compared to the values established earlier. It was found that the estimated PCE are smaller than those being used in Bangladesh.

  20. In-car particles and cardiovascular health: an air conditioning-based intervention study.

    Science.gov (United States)

    Chuang, Hsiao-Chi; Lin, Lian-Yu; Hsu, Ya-Wen; Ma, Chih-Ming; Chuang, Kai-Jen

    2013-05-01

    Exposure to traffic-related particulate matter (PM) is considered a potential risk for cardiovascular events. Little is known about whether improving air quality in car can modify cardiovascular effects among human subjects during commuting. We recruited a panel of 60 healthy subjects to commute for 2 h by a car equipped with an air conditioning (AC) system during the morning rush hour in Taipei. Operation modes of AC system using outside air (OA-mode), circulating inside air (IA-mode) and turning off (Off-mode) were examined. Repeated measurements of heart rate variability (HRV) indices, PM≤2.5 μm in aerodynamic diameter (PM2.5) and noise level were conducted for each participant in different modes during the commute. We used linear mixed-effects models to associate HRV indices with in-car PM2.5. We found that decreases in HRV indices were associated with increased levels of in-car PM2.5. For Off-mode, an interquartile range (IQR) increase in in-car PM2.5 with 15-min moving average was associated with 2.7% and 4.1% decreases in standard deviation of NN intervals (SDNN) and the square root of the mean of the sum of the squares of differences between adjacent NN intervals (r-MSSD), respectively. During OA and IA modes, participants showed slight decreases in SDNN (OA mode: 0.1%; IA mode: 1.3%) and r-MSSD (OA mode: 1.1%; IA mode: 1.8%) by an IQR increase in in-car PM2.5 with 15-min moving average. We concluded that in-car PM2.5 is associated with autonomic alteration. Utilization of the car's AC system can improve air quality and modify the effects of in-car PM2.5 on HRV indices among human subjects during the commute. Copyright © 2013 Elsevier B.V. All rights reserved.

  1. Evaluation of wind noise in passenger car compartment in consideration of auditory masking and sound localization; Chokaku masking to hoko chikaku wo koryoshita kazekirion hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Hoshino, H. [Toyota Central Research and Development Labs., Inc., Aichi (Japan); Kato, H. [Toyota Motor Corp., Aichi (Japan)

    1998-05-01

    Discussed is a method for evaluating wind noise in passenger car compartment based on human auditory characteristics. In the study, noise in the compartment of a passenger car travelling at a constant speed is collected by use of a dummy head, and the collected noise is analyzed in view of the masking effect, directional sensation produced by binaural hearing, etc. A masked spectrum of noise in the compartment of a 6-cylinder vehicle travelling at 120km/h is analyzed, and it is found that some frequency bands, especially the band centering on 300Hz, are masked by a loud noise component falling in a low frequency band of 180Hz or lower. By use of masked spectrum analysis, the level of noise that is actually audible to human ears can be calculated. The noise level thus determined by masked spectrum analysis and the noise direction determined by a binaural signal processing model are examined, and then it is found that the noise direction is clearly determined when the noise belongs in a 450Hz band or higher where wind noise prevails. On the bases of the above-mentioned results and the directional sensation produced by binaural hearing, a `binaural wind noise evaluation method` is compiled. 20 refs., 9 figs., 1 tab.

  2. Safety of railroad passenger vehicle dynamics : OMNISIM simulation and test correlations for passenger rail cars

    Science.gov (United States)

    2002-07-01

    The purpose of the work is to validate the safety assessment methodology previously developed for passenger rail vehicle dynamics, which requires the application of simulation tools as well as testing of vehicles under different track scenarios. This...

  3. Influence of European passenger cars weight to exhaust CO2 emissions

    International Nuclear Information System (INIS)

    Zervas, Efthimios; Lazarou, Christos

    2008-01-01

    The increase of atmospheric CO 2 concentration influences climate changes. The road transport sector is one of the main anthropogenic sources of CO 2 emissions in the European Union (EU). One of the main parameters influencing CO 2 emissions from passenger cars (PCs) is their weight, which increases during last years. For the same driving distance, heavier vehicles need more work than lighter ones, because they have to move an extra weight, and thus more fuel is consumed and thus increased CO 2 emissions. The weight control of new PCs could be an efficient way to control their CO 2 emissions. After an analysis of the EU new PCs market, their segment distribution and their weight, some estimations for 2020 are presented. Based on this analysis, 13 base scenarios using several ways for the control of the weight of future European new PCs are used to estimate their CO 2 emissions and the benefit of each scenario. The results show that a significant benefit on CO 2 emissions could be achieved if the weight of each PC does not exceed an upper limit, especially if this limit is quite low. The benefit obtained by limitations of weight is higher than the benefit obtained from the expected decreased future fuel consumption. Similar results are obtained when the weight of new PCs does not exceed an upper limit within each segment, or when the weight of each new PC decreases. (author)

  4. Emission concepts for future passenger car diesel engines; Emissionskonzepte fuer zukuenftige Pkw-Dieselmotoren

    Energy Technology Data Exchange (ETDEWEB)

    Krueger, M.; Wiartalla, A.; Lichtenberg, T.; Koerfer, T. [FEV Motorentechnik, Aachen (Germany)

    2003-07-01

    In order to keep the current success of the Diesel powered passenger cars also for the future, intensive development effort is absolutely necessary in the near future. A special challenge is presented by the already confirmed or discussed future emission standards. However, every chance must be taken to keep the fuel consumption of the diesel engine respectively diesel powered vehicle on the lowest possible level. In front of this background measures concerning combustion system development as well as exhaust gas aftertreatment are analyzed in this report with respect to their influence on emission reduction and fuel consumption. It can be summarized, that still a significant emission reduction potential exists for the passenger car diesel engine. However, fulfilling the next step of emission legislation, getting effective after 2005, only by combustion system improvement, seems to be a difficult way to go from todays point of view. Especially with respect to fuel consumption, an efficient combination of combustion improvement and exhaust gas aftertreatment represents a more promising solution for the future. Most important for a successful realisation of such an approach will be the overall power consumption of the exhaust gas aftertreatment device. This does also include the thermomanagement of the engine and exhaust gas system as well as the energy losses due to the regeneration demands of the discontinuously working NO{sub x}-and particulate trap. Considering this last issue, a fuel additive as particulate trap regeneration aid as well as the fuel sulphur content respectively the sulphur sensitivity of the NO{sub x}-trap will play a significant role in the future. (orig.) [German] Um den Erfolg des Diesel-Pkw's auch zukuenftig sicherzustellen, sind intensive Entwicklungsarbeiten notwendig. Eine besondere Herausforderung stellen die zukuenftig zu erfuellenden Emissionsanforderungen dar. Dabei muessen alle moeglichen Massnahmen ergriffen werden, um den

  5. Passenger vehicles that minimize the costs of ownership and environmental damages in the Indian market

    International Nuclear Information System (INIS)

    Gilmore, Elisabeth A.; Patwardhan, Anand

    2016-01-01

    Highlights: • Full costs (private and social) are evaluated for Indian passenger cars. • Diesel has low ownership costs, but higher climate and health damages. • Compressed natural gas cars have lower costs and damages than petrol cars. • Electric cars have higher damages due to electricity generation emissions. • CNG and less carbon intensive electricity minimizes Indian cars’ full cost. - Abstract: Rapid expansion of population and income growth in developing countries, such as India, is increasing the demand for many goods and services, including four-wheeled passenger cars. Passenger cars provide personal mobility; however, they also have negative implications for human wellbeing from increased air pollutants and greenhouse gases (GHG). Here, we evaluate the range of passenger vehicles available in the Indian market to identify options that minimize costs, human health effects and climate damages. Our approach is to compare alternative fuel/powertrain vehicles with similar conventional gasoline fueled vehicles and assess the differences in full (private and societal) costs for each pair. Private costs are the combination of capital costs and the discounted expected future fuel costs over the vehicle lifetime. The costs to human health from air quality are calculated using intake fractions to estimate exposure and literature values for the damage costs adjusted by benefits transfer methods. We use the Social Cost of Carbon to estimate climate damages. We find that, on average, the net present value (NPV) of the full costs of compressed natural gas (CNG) vehicles are lower than comparable gasoline vehicles, while, diesel vehicles have higher costs. Presently, electric vehicles have higher private costs (due to high capital costs) and societal costs (due to electricity generation emissions). Either a less carbon intensive electricity grid or an increase in the CNG fleet would minimize total costs, human health effects and GHG emissions from the

  6. Lateral car collisions : characteristics of lateral car collisions based on SWOV accident investigation.

    NARCIS (Netherlands)

    1979-01-01

    During 1976 and part of 1977 the Dutch institute for road safety research SWOV carried out the field work for an accident study involving passenger cars. The purpose of this crash injury investigation was to evaluate the influence of relevant crash safety factors (like safety belts and head

  7. Optimal Planning of the Nordic Transmission System with 100% Electric Vehicle Penetration of passenger cars by 2050

    DEFF Research Database (Denmark)

    Graabak, Ingeborg; Wu, Qiuwei; Warland, Leif

    2016-01-01

    This paper presents the optimal planning of the Nordic backbone transmission system with 100% electric vehicle penetration of passenger cars by 2050. Electric vehicles will play an important role in the future energy systems and can reduce the greenhouse gas emission from the transport sector....... However, the electric vehicles will increase the electricity consumption and might induce congestions in the transmission systems. In order to deal with the electricity consumption increase from the electric vehicle integration into the power system and maximize the social welfare, the optimal investments...... of the Nordic transmission system are studied. Case studies were conducted using the market simulation model EMPS and two electric vehicle charging scenarios: a spot price based scenario and a dumb charging scenario. The electric vehicle charging power is assumed to be 3.68 kW with 1 phase 16A. The complete...

  8. Present and future energy consumption for passenger transportation in Germany

    Energy Technology Data Exchange (ETDEWEB)

    Kuhne, M.; Wolffram, U.

    1981-01-01

    Passenger transportation in Germany was investigated in order to determine real energy consumption. For typical passengers, energy consumption for overland travel and charter flights was studied. The energy needed for air traffic was compared with that for transportation overland (railway, car, bus), taking into account transportation to the airport or railway station. Transportation makes up about 17% of German primary energy consumption, i.e., road traffic 14%, railway traffic 1.6%, and air traffic 1%. Specific energy consumption (overland travel) of intercity trains, airplanes and cars is in the proportion 1.0 to 3.7 to 4.0 (1980) and is expected to be 1 to 2.4 to 3.1 by the year 2000. For holiday trips, specific energy consumption for bus, train, car and airplane travel is in the proportion 1.0 to 1.4 to 3.6 to 3.4 (1980) and is expected to be 1 to 1.4 to 2.5 to 2.9 by 2000. (ESA)

  9. 49 CFR 238.409 - Forward end structures of power car cabs.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Forward end structures of power car cabs. 238.409... II Passenger Equipment § 238.409 Forward end structures of power car cabs. This section contains requirements for the forward end structure of the cab of a power car. (A conceptual implementation of this end...

  10. 49 CFR 238.411 - Rear end structures of power car cabs.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Rear end structures of power car cabs. 238.411... II Passenger Equipment § 238.411 Rear end structures of power car cabs. The rear end structure of the cab of a power car shall be designed to include the following elements, or their structural equivalent...

  11. Research on the compressive strength of a passenger vehicle roof

    Science.gov (United States)

    Zhao, Guanglei; Cao, Jianxiao; Liu, Tao; Yang, Na; Zhao, Hongguang

    2017-05-01

    To study the compressive strength of a passenger vehicle roof, this paper makes the simulation test on the static collapse of the passenger vehicle roof and analyzes the stress and deformation of the vehicle roof under pressure in accordance with the Roof Crush Resistance of Passenger Cars (GB26134-2010). It studies the optimization on the major stressed parts, pillar A, pillar B and the rail of roof, during the static collapse process of passenger vehicle roof. The result shows that the thickness of pillar A and the roof rail has significant influence on the compressive strength of the roof while that of pillar B has minor influence on the compressive strength of the roof.

  12. Variability of levels and composition of PM10 and PM2.5 in the Barcelona metro system

    Directory of Open Access Journals (Sweden)

    E. de Miguel

    2012-06-01

    Full Text Available From an environmental perspective, the underground metro system is one of the cleanest forms of public transportation in urban agglomerations. Current studies report contradicting results regarding air quality in the metro systems: whereas some reveal poor air quality, others report PM levels which are lower or of the same order of magnitude than those measured in traffic sites above ground level. The present work assesses summer and winter indoor air quality and passenger exposure in the Barcelona metro, focusing on PM levels and their metal contents. In addition, the impact on indoor air quality of platform screen door systems (automated systems consisting of closed rail track and platforms is evaluated, to determine whether these systems reduce passenger exposure to PM when compared with conventional systems (open tracks and platforms. In the Barcelona metro PM levels inside the trains in summer are amongst the lowest reported for worldwide metro systems (11–32 μg m−3 PM2.5. This is most likely due to the air conditioning system working in all carriages of the Barcelona metro during the whole year. Levels were considerably higher on the platforms, reaching mean levels of 46 and 125 μg m3 in the new (L9 and old (L3 lines, respectively. PM10 data are also reported in the present study, but comparison with other metro systems is difficult due to the scarcity of data compared with PM2.5. Results showed distinct PM daily cycles, with a drastic increase from 06:00 to 07:00 a.m., a diurnal maximum from 07:00 to 10:00 p.m., and marked decrease between 10:00 p.m. and 05:00 a.m. The elements with the highest enrichment were those associated with wheel or brake abrasion products (Ba, Fe, Cu, Mn, Cr, Sb, As, Mo, Co, Sr, among others. Laminar hematite (Fe2O3 was the dominant particle type, being mainly originated by mechanical abrasion of the rail track and wheels. Regarding passenger exposure to PM, the contribution of commuting by metro was

  13. IMPROVEMENT OF LIFE SUPPORT SYSTEMS OF PASSENGER ROLLING STOCK: PATENT REVIEW

    Directory of Open Access Journals (Sweden)

    S. R. Kolesnykov

    2018-02-01

    Full Text Available Purpose. Inventors and researchers of the world are focused on improvements of basic life support systems including provision of quality microclimate parameters in a car of the rolling stock. The research is aimed at reviewing and analyzing patents in the field of climate comfort, heating, ventilation and air conditioning (CCHVAC of railway passenger cars (the chronological framework: 2011-2017 from the date of publication. Мethodology. During the study there were reviewed patents (foreign and domestic ones in the field of CCHVAC in passenger vehicles, in particular railway cars, their optimization and ways of managing them. Patent search was carried out according to certain search criteria: keywords, time frames and in various patent systems of the world. An interdisciplinary approach was used. Findings. Based on the search results, 157 patents were found, 21 documents of which were selected for analysis. Patents are systematized into three groups: "New technical and technological solutions in systems and functioning facilities of HVAC ", "New and improved solutions for HVAC system management in a vehicle", "Air ozonation in passenger cars". It is established that all patents have one of the aspects that have solutions to the issues of more environmentally friendly, energy efficient and safe application of CCHVAC systems in railway transport. Originality. It was proved a high level of link penetration in various technical fields, which include patents with CCHVAC. It is established that it is characteristic for them to designate the majority of patent solutions for use not in the purely railway industry, but in transport in general. Practical value. Confirmation of the high level of link penetration in various technical fields will make it possible to reflect technical problems with CCHVAC and technologies for their solution throughout the world. This will contribute to a more intensive technological upgrade in the improvement of life support

  14. Car stickers for 2012

    CERN Multimedia

    GS Department

    2011-01-01

    The 2012 car stickers are now available. Holders of blue car stickers will receive by internal mail their 2012 car stickers as of 5 December. Holders of red car stickers are kindly requested to come to the Registration Service (Building 55,1st floor) to renew their 2011 stickers. This service is open from Monday to Friday from 7.30 am to 5.30 pm non-stop. Documents related to the vehicles concerned are mandatory. Reception and Access Control Service – GS/IS/SIS General Infrastructure Services Department

  15. Car stickers for 2011

    CERN Multimedia

    GS Department

    2010-01-01

    The 2011 car stickers are now available. Holders of blue car stickers will receive their 2011 car stickers by internal mail as of 15 December.   Holders of red car stickers are kindly requested to come to the Registration Service (Building 55,1st floor) to renew their 2011 stickers. This service is open from Monday to Friday from 7.30 am to 5.30 pm non-stop. Documents for the vehicles concerned must be presented. Reception and Access Control Service – GS/ISG/SIS General Infrastructure Services Department

  16. Assessing community child passenger safety efforts in three Northwest Tribes.

    Science.gov (United States)

    Smith, M L; Berger, L R

    2002-12-01

    To identify strengths and weaknesses in community based child passenger safety programs by developing a scoring instrument and conducting observations of child restraint use in three Native American communities. The three communities are autonomous Tribal reservations in the Pacific Northwest. Their per capita incomes and rates of unemployment are comparable. In each community, 100 children under 5 years old were observed for car seat use. A six item community assessment tool (100 points maximum) awarded points for such items as the type (primary or secondary) and enforcement of child restraint laws; availability of car seats from distribution programs; extent of educational programs; and access to data on vehicle injuries. For children from birth to 4 years, the car seat use rate ranged from 12%-21%. Rates for infants (71%-80%) far exceeded rates for 1-4 year old children (5%-14%). Community scores ranged from 0 to 31.5 points. There was no correlation between scores and observed car seat use. One reason was the total lack of enforcement of restraint laws. A community assessment tool can highlight weaknesses in child passenger efforts. Linking such a tool with an objective measure of impact can be applied to other injury problems, such as fire safety or domestic violence. The very process of creating and implementing a community assessment can enhance agency collaboration and publicize evidence based "best practices" for injury prevention. Further study is needed to address methodologic issues and to examine crash and medical data in relation to community child passenger safety scores.

  17. NOx Emissions from Diesel Passenger Cars Worsen with Age.

    Science.gov (United States)

    Chen, Yuche; Borken-Kleefeld, Jens

    2016-04-05

    Commonly, the NOx emissions rates of diesel vehicles have been assumed to remain stable over the vehicle's lifetime. However, there have been hardly any representative long-term emission measurements. Here we present real-driving emissions of diesel cars and light commercial vehicles sampled on-road over 15 years in Zurich/Switzerland. Results suggest deterioration of NOx unit emissions for Euro 2 and Euro 3 diesel technologies, while Euro 1 and Euro 4 technologies seem to be stable. We can exclude a significant influence of high-emitting vehicles. NOx emissions from all cars and light commercial vehicles in European emission inventories increase by 5-10% accounting for the observed deterioration, depending on the country and its share of diesel cars. We suggest monitoring the stability of emission controls particularly for high-mileage light commercial as well as heavy-duty vehicles.

  18. Understanding adolescents' intentions to commute by car or bicycle as adults

    DEFF Research Database (Denmark)

    Sigurdardottir, Sigrun Birna; Kaplan, Sigal; Møller, Mette

    2013-01-01

    This study focuses on the intentions of adolescents to commute by car or bicycle as adults. The behavioral model is based on intrapersonal and interpersonal constructs from the theory of planned behavior extended to include constructs from the institutional, community and policy domains. Data from...... a survey among Danish adolescents is analyzed. It is found that car use intentions are related to positive car passenger experience, general interest in cars, and car ownership norms, and are negatively related to willingness to accept car restrictions and perceived lack of behavioral control. Cycling...

  19. 49 CFR 238.207 - Link between coupling mechanism and car body.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Link between coupling mechanism and car body. 238.207 Section 238.207 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL... Requirements for Tier I Passenger Equipment § 238.207 Link between coupling mechanism and car body. All...

  20. Hybrid-Electric Passenger Car Carbon Dioxide and Fuel Consumption Benefits Based on Real-World Driving.

    Science.gov (United States)

    Holmén, Britt A; Sentoff, Karen M

    2015-08-18

    Hybrid-electric vehicles (HEVs) have lower fuel consumption and carbon dioxide (CO2) emissions than conventional vehicles (CVs), on average, based on laboratory tests, but there is a paucity of real-world, on-road HEV emissions and performance data needed to assess energy use and emissions associated with real-world driving, including the effects of road grade. This need is especially great as the electrification of the passenger vehicle fleet (from HEVs to PHEVs to BEVs) increases in response to climate and energy concerns. We compared tailpipe CO2 emissions and fuel consumption of an HEV passenger car to a CV of the same make and model during real-world, on-the-road network driving to quantify the in-use benefit of one popular full HEV technology. Using vehicle specific power (VSP) assignments that account for measured road grade, the mean CV/HEV ratios of CO2 tailpipe emissions or fuel consumption defined the corresponding HEV "benefit" factor for each VSP class (1 kW/ton resolution). Averaging over all VSP classes for driving in all seasons, including temperatures from -13 to +35 °C in relatively steep (-13.2 to +11.5% grade), hilly terrain, mean (±SD) CO2 emission benefit factors were 4.5 ± 3.6, 2.5 ± 1.7, and 1.4 ± 0.5 for city, exurban/suburban arterial and highway driving, respectively. Benefit factor magnitude corresponded to the frequency of electric-drive-only (EDO) operation, which was modeled as a logarithmic function of VSP. A combined model explained 95% of the variance in HEV benefit for city, 75% for arterial and 57% for highway driving. Benefit factors consistently exceeded 2 for VSP classes with greater than 50% EDO (i.e., only city and arterial driving). The reported HEV benefits account for real-world road grade that is often neglected in regulatory emissions and fuel economy tests. Fuel use HEV benefit factors were 1.3 and 2 for the regulatory highway (HWFET) and city (FTP) cycles, respectively, 18% and 31% higher than the EPA adjusted

  1. Passenger Transportation and Travel Curriculum Guide. Final Report.

    Science.gov (United States)

    Lininger, Carol

    This curriculum guide provides materials for a course in passenger transportation and travel. The four-credit, competency-based program provides students with skills necessary to obtain employment in the aviation industry, travel agencies, hotel/motel management, and car rental agencies. An overview of vocational-technical education at the school…

  2. Identification of the sources of PM10 in a subway tunnel using positive matrix factorization.

    Science.gov (United States)

    Park, Duckshin; Lee, Taejeong; Hwang, Doyeon; Jung, Wonseok; Lee, Yongil; Cho, KiChul; Kim, Dongsool; Lees, Kiyoung

    2014-12-01

    The level of particulate matter of less than 10 μm diameter (PM10) at subway platforms can be significantly reduced by installing a platform screen-door system. However, both workers and passengers might be exposed to higher PM10 levels while the cars are within the tunnel because it is a more confined environment. This study determined the PM10 levels in a subway tunnel, and identified the sources of PM10 using elemental analysis and receptor modeling. Forty-four PM10 samples were collected in the tunnel between the Gireum and Mia stations on Line 4 in metropolitan Seoul and analyzed using inductively coupled plasma-atomic emission spectrometry and ion chromatography. The major PM10 sources were identified using positive matrix factorization (PMF). The average PM10 concentration in the tunnels was 200.8 ± 22.0 μg/m3. Elemental analysis indicated that the PM10 consisted of 40.4% inorganic species, 9.1% anions, 4.9% cations, and 45.6% other materials. Iron was the most abundant element, with an average concentration of 72.5 ± 10.4 μg/m3. The PM10 sources characterized by PMF included rail, wheel, and brake wear (59.6%), soil combustion (17.0%), secondary aerosols (10.0%), electric cable wear (8.1%), and soil and road dust (5.4%). Internal sources comprising rail, wheel, brake, and electric cable wear made the greatest contribution to the PM10 (67.7%) in tunnel air. Implications: With installation of a platform screen door, PM10 levels in subway tunnels were higher than those on platforms. Tunnel PM10 levels exceeded 150 µg/m3 of the Korean standard for subway platform. Elemental analysis of PM10 in a tunnel showed that Fe was the most abundant element. Five PM10 sources in tunnel were identified by positive matrix factorization. Railroad-related sources contributed 68% of PM10 in the subway tunnel.

  3. Monitoring of Air Quality in Passenger Cabins of the Athens Metro

    Science.gov (United States)

    Tsairidi, Evangelia; Assimakopoulos, Vasiliki D.; Assimakopoulos, Margarita-Niki; Barbaresos, Nicolaos; Karagiannis, Athanassios

    2013-04-01

    The air pollution induced by various transportation means combines the emission of pollutants with the simultaneous presence of people. In this respect, the scientific community has focused its efforts in studying both the air quality within busy streets and inside cars, buses and the underground railway network in order to identify the pollutants' sources and levels as well as the human exposure. The impact of the air pollution on commuters of the underground may be more severe because it is a confined space, extended mostly under heavily trafficked urban streets, relies on mechanical ventilation for air renewal and gathers big numbers of passengers. The purpose of the present work is to monitor the air quality of the city of Athens Metro Network cabins and platforms during the unusually hot summer of 2012. For that cause particulate matter (PM10, PM2.5, PM1), carbon dioxide (CO2), the number of commuters along with temperature (T) and humidity (RH) were recorded inside the Athens Metro Blue Line trains (covering a route from the centre of Athens (Aigaleo) to the Athens International Airport) and on the platforms of a central (Syntagma) and a suburban-traffic (Doukissis Plakentias) station between June and August. The data collection included six different experiments that took place for 2 consecutive working days each, for a time period of 6 weeks from 6:30 am too 7:00 pm in order to account for different outdoor climatic conditions and for morning and evening rush hours respectively. Measurements were taken in the middle car of the moving trains and the platform end of the selected stations. The results show PM concentrations to be higher (approximately 2 to 5 times) inside the cabins and o the platforms of the underground network as compared to the outdoor levels monitored routinely by the Ministry of Environment. Moreover, PM1, PM2.5 and PM10 average concentrations recorded at the Syntagma Station Platform were almost constantly higher reaching 11 μg m-3 47

  4. Upscaling of a Batch De-vulcanization Process for Ground Car Tire Rubber to a Continuous Process in a Twin Screw Extruder

    NARCIS (Netherlands)

    Saiwari, Sitisaiyidah; van Hoek, Johannes Wilhelmus; Dierkes, Wilma K.; Reuvekamp, Louis A.E.M.; Heideman, G.; Blume, Anke; Noordermeer, Jacobus W.M.

    2016-01-01

    As a means to decrease the amount of waste tires and to re-use tire rubber for new tires, devulcanization of ground passenger car tires is a promising process. Being an established process for NR and EPDM, earlier work has shown that for ground passenger car tire rubber with a relatively high amount

  5. Prototype design of a collision protection system for cab car engineers - fabrication and test.

    Science.gov (United States)

    2015-06-01

    Advancements in the structural crashworthiness of passenger rail cars now make it possible to preserve the compartmentalized : space occupied by a cab car engineer during a train collision. In order to translate this additional protection into improv...

  6. Estimate of potential benefit for Europe of fitting Autonomous Emergency Braking (AEB) systems for pedestrian protection to passenger cars.

    Science.gov (United States)

    Edwards, Mervyn; Nathanson, Andrew; Wisch, Marcus

    2014-01-01

    current generation AEB systems to about €3.5 billion for a reference limit system (i.e., best performance thought technically feasible at present). Dividing these values by the number of new passenger cars registered in Europe per year gives an indication that the cost of a system per car should be less than ∼€80 to ∼€280 for it to be cost effective. The potential benefit of fitting AEB systems to cars in Europe for pedestrian protection has been estimated and the results interpreted to indicate the upper limit of cost for a system to allow it to be cost effective.

  7. High levels of incorrect use of car seat belts and child restraints in Fife--an important and under-recognised road safety issue.

    Science.gov (United States)

    Campbell, H; Macdonald, S; Richardson, P

    1997-03-01

    To pilot data collection instruments and to make a preliminary estimate of the level of incorrect use of car seat belts and child restraints in Fife, Scotland. Cross sectional survey of cars containing adults and children at a number of public sites across Fife in 1995 to assess use of car occupant restraints. Trained road safety officers assessed whether seat restraints were appropriate for the age of the passengers and whether restraints were used correctly. These assessments were based on standards published by the Child Accident Prevention Trust. The survey gathered data from 596 occupants in 180 cars: 327 adults and 269 children. Ten per cent of drivers who were approached refused to participate. Car occupant restraint was assessed in 180 drivers, 151 front seat passengers, and 265 rear seat passengers. Three hundred and sixty one occupants wore seat belts, 68 were restrained by a seat belt and booster cushion, 63 in toddler seats, 25 in two way seats, and 18 in rear facing infant carriers. Ninety seven per cent of drivers, 95% of front seat passengers, and 77% of rear seat passengers were restrained. However, in 98 (52%) vehicles at least one passenger was restrained by a device that was used incorrectly. Seven per cent of adults and 28% of children were secured incorrectly. The commonest errors were loose seat belts and restraint devices not adequately secured to the seat. Rates of incorrect use were highest in child seat restraints, reaching 60% with two way seats and 44% with rear facing infant seats. The incorrect use of car occupant restraints is an under-recognised problem, both by health professionals, and the general public. Incorrect use has been shown to reduce the effectiveness of restraints, can itself result in injury, and is likely to be an important factor in child passenger injuries. The correct use of car seat restraints merits greater attention in strategies aiming to reduce road traffic casualties. Areas of intervention that could be

  8. Continuous injection rate-shaping for passenger-car diesel engines. Potential, limits and feasibility; Kontinuierliche Einspritzverlaufsformung in Pkw-Dieselmotoren. Potenziale, Grenzen und Realisierungschancen

    Energy Technology Data Exchange (ETDEWEB)

    Predelli, Oliver; Gratzke, Ralf; Sommer, Ansgar; Marohn, Ralf [Ingenieurgesellschaft Auto und Verkehr GmbH, Berlin (Germany); Atzler, Frank; Schuele, Harry; Kastner, Oliver; Nozeran, Nicolas [Continental Automotive GmbH, Regensburg (Germany)

    2010-07-01

    Injection-rate shaping for passenger-car diesel engines is a technique on the verge of a breakthrough. In addition to reducing particulate emission, the method is capable of significantly cutting combustion noise, the Achilles heel of the DI diesel combustion process. As a result, injection-rate shaping shows clear advantages over alternative lowemission combustion processes, such as PCCI, which, although also capable of improving raw emissions in relation to NO{sub x} and soot, are less convincing from the aspect of diesel knock and the emission of CO and CO{sub 2}. Of the modern Common-Rail injection systems, only two permit continuous injection-rate shaping in addition to the hitherto customary strategy of multiple injection. One of them is the Continental PCR NG system. This uses piezo-actuated Common-Rail injectors with direct actuation of the injector nozzle needle. The electronic engine control system provides the capability of determining how far the injector nozzle needle opens. The ability to control the injection curve of each individual injection event gives the engine developer new degrees of freedom in optimizing the combustion process. This paper investigates the way in which the operating behavior of a passenger-car diesel engine is affected by an injection-rate that can be shaped flexibly across broad ranges. Injection-rate shaping aims to use high injection pressures at part load without affecting acoustics and with a view to achieving a significant improvement in emission behavior. The investigation also points out this technique's limits in individual operating points. It furthermore demonstrates approaches suitable for use in mass production with regard to controlling injection-rate shaping in real time in the engine control unit as a way of providing combustion-process stability over the life of the engine. (orig.)

  9. Electric vehicles in China: emissions and health impacts.

    Science.gov (United States)

    Ji, Shuguang; Cherry, Christopher R; J Bechle, Matthew; Wu, Ye; Marshall, Julian D

    2012-02-21

    E-bikes in China are the single largest adoption of alternative fuel vehicles in history, with more than 100 million e-bikes purchased in the past decade and vehicle ownership about 2× larger for e-bikes as for conventional cars; e-car sales, too, are rapidly growing. We compare emissions (CO(2), PM(2.5), NO(X), HC) and environmental health impacts (primary PM(2.5)) from the use of conventional vehicles (CVs) and electric vehicles (EVs) in 34 major cities in China. CO(2) emissions (g km(-1)) vary and are an order of magnitude greater for e-cars (135-274) and CVs (150-180) than for e-bikes (14-27). PM(2.5) emission factors generally are lower for CVs (gasoline or diesel) than comparable EVs. However, intake fraction is often greater for CVs than for EVs because combustion emissions are generally closer to population centers for CVs (tailpipe emissions) than for EVs (power plant emissions). For most cities, the net result is that primary PM(2.5) environmental health impacts per passenger-km are greater for e-cars than for gasoline cars (3.6× on average), lower than for diesel cars (2.5× on average), and equal to diesel buses. In contrast, e-bikes yield lower environmental health impacts per passenger-km than the three CVs investigated: gasoline cars (2×), diesel cars (10×), and diesel buses (5×). Our findings highlight the importance of considering exposures, and especially the proximity of emissions to people, when evaluating environmental health impacts for EVs.

  10. Analysis of the CO2 emissions and of the other characteristics of the European market of new passenger cars. 2. Segment analysis

    International Nuclear Information System (INIS)

    Zervas, Efthimios

    2010-01-01

    This article analyzes the engine and vehicle characteristics and the CO 2 emissions of the new passenger cars for all segments of the European market. As in the first article of this work, the target is to find the real market parameters influencing exhaust CO 2 emissions. The present analysis is focused on the segment sales distribution (EU average and within each country) and also in four parameters of each segment influencing CO 2 emissions: average vehicle weight, average engine capacity, average maximum and specific power. The second part of this work concerns the CO 2 emissions of each segment on the New European Driving Cycle and its urban and extra urban parts.

  11. Analysis of CO2 emissions and of the other characteristics of the European market of new passenger cars. 3. Brands analysis

    International Nuclear Information System (INIS)

    Zervas, Efthimios

    2010-01-01

    This article analyses the engine and vehicle characteristics and CO 2 emissions of the new passenger cars for the thirteen major brands of the European market. As in the first two articles of this work, the target is to find the real market parameters influencing exhaust CO 2 emissions. This analysis is focused on the sales distribution of the major brands, EU average and within each country, and four main parameters of each brand having an impact on CO 2 emissions: average vehicle weight, average engine capacity, average maximum and specific power. The average CO 2 emissions of each brand on the new European driving cycle and its urban and extra urban parts are examined at the last part of this article.

  12. Bases of a fuel saving program for the passenger car traffic in Austria and benefit-cost-analysis of individual fuel economics. Grundlagen eines Energiesparkonzeptes fuer den PKW-Verkehr in Oesterreich und Nutzen-Kosten-Untersuchung einzelner Energiesparmassnahmen

    Energy Technology Data Exchange (ETDEWEB)

    Bruner-Newton, I.

    1979-01-01

    The influences on the fuel consumption of the individual automobile are investigated and their importance is appraised. From these data measures are derived to obtain a sensible fuel consumption. After a survey of conventional benefit-cost-analyses, guide lines for a benefit-cost-analyses of fuel economies in passenger car traffic are given. A target system is established which includes the most important criteria, which determine the total fuel consumption of passenger cars in Austria. Hereby it is possible to calculate the fuel saving potential of a certain measure. The economy of a measure is characterized by a benefit-cost-ratio. The developed methods of appraisal are applied to 14 measures and prove to be a suitable instrument for a systematic and comparable analyses of the individual measures. The measures are listed according to their economy when examining three different periods. It is shown which average annual fuel saving potential can be achieved by means of which annual costs.

  13. Estimate of the technological costs of CO{sub 2} emission reductions in passenger cars. Emission reduction potentials and their costs; Technikkostenschaetzung fuer die CO{sub 2}-Emissionsminderung bei Pkw. Emissionsminderungspotenziale und ihre Kosten

    Energy Technology Data Exchange (ETDEWEB)

    Herbener, Reinhard; Jahn, Helge; Wetzel, Frank [Umweltbundesamt, Dessau-Rosslau (Germany). Fachgebiet I 3.2 - Schadstoffminderung und Energieeinsparung im Verkehr

    2008-08-06

    The Federal Environmental Office intended to identify the current fuel consumption reduction potential and the cost of efficiency-enhancing measures on passenger cars. For this purpose, an extensive bibliographic search was carried out, and experts from research institutes and from the automobile supplier industry were asked for their opinion. The results are published in table form. (orig.)

  14. Improvement of crash compatibility between cars

    NARCIS (Netherlands)

    Huibers, J.A.H.M.; Faerber, E.; Cesari, D.; Hobbs, A.C.; Kampen, B. van; Paez, J.; Wykes, N.J.

    1998-01-01

    This paper will provide an overview of the research work of the European Enhanced Vehicle-safety Committee (EEVC) in the field of crash compatibility between passenger cars. Since July 1997 the EC Commission is partly funding the research work of EEVC. The running period of this project will be two

  15. Characteristics of PM10 and CO2 concentrations on 100 underground subway station platforms in 2014 and 2015

    Science.gov (United States)

    Hwang, Sung Ho; Park, Wha Me; Park, Jae Bum; Nam, Taegyun

    2017-10-01

    In this study, the concentrations of particulate matter 10 μm or less in diameter (PM10) and carbon dioxide (CO2) were measured in 100 underground subway stations, and the potential health risks of PM10, and environmental factors affecting these concentrations were analyzed. The concentrations were measured from May 2014 to September 2015 in stations along Seoul Metro lines 1-4. There were significantly different PM10 concentrations among the underground subway stations along lines 1, 2, 3, and 4. The PM10 concentrations were associated with the CO2 concentrations, construction years, station depths, and numbers of passengers. The underground PM10 concentrations were significantly higher than the outdoor PM10 concentrations. In addition, the PM10 concentrations were higher in the stations that were constructed in the 1970s than in those constructed after the 1970s. The PM10 and CO2 concentrations varied significantly, depending on the construction year and number of passengers. The hazard quotient is higher than the acceptable level of 1.0 μg kg-1 day for children, indicating that they are at risk of exposure to unsafe PM10 levels when travelling by the metro. Therefore, stricter management may be necessary for the stations constructed in the 1970s as well as those with higher numbers of passengers.

  16. CERN car sharing scheme now open to everyone

    CERN Multimedia

    GS Department

    2011-01-01

    The CERN car sharing service is a self-service scheme providing a pool of 30 CERN cars available for pick-up free of charge from 13 points around the Meyrin and Prévessin sites. From Thursday, 1st December 2011, the service will be open to all members of the CERN personnel and contractors' personnel, in the framework of their professional activities at CERN only. The conditions of use can be consulted at: http://gs-dep.web.cern.ch/en/content/Mobility/Car_sharing To be able to use the service, members of the CERN personnel and contractors' personnel must: have a contractual link to CERN, possess an e-mail address registered in the CERN databases; hold an RFID access card, which can be obtained from the CERN Car Pool on presentation of a valid CERN access card. Car Pool, Building 130-R-012, open Monday-Friday, 8.00 a.m.-12.00 noon/1.00 p.m.-5.00 p.m. https://gs-dep.web.cern.ch/en/content/car-pool GS-IS

  17. Car sharing à la carte

    CERN Multimedia

    Anaïs Schaeffer

    2012-01-01

    Do you want to make your commute to CERN easier, while saving money at the same time? Would you prefer not to spend a quarter of an hour crawling round the CERN car parks looking for a space? If so, read on: this article might well be of great interest to you.   We would like to draw your attention to a well established, albeit sadly under-used, method of transport: car sharing. To promote car-sharing, the GS Department has stepped in to call on the services of the Swiss firm Green Monkeys which specialises in this user-friendly and intelligent transport scheme. The company’s slogan is:  “Car-sharing as you want, when you want and as much as you want”. The principle is very straightforward. To use this car-sharing facility, you simply complete your free online registration with Green Monkeys, providing the following details: your journey, departure time, arrival time and days of the week, and indicating whether you are a passenger or driver or both. &a...

  18. Velocity-dependent emission factors of benzene, toluene and C 2-benzenes of a passenger car equipped with and without a regulated 3-way catalyst

    Science.gov (United States)

    Heeb, Norbert V.; Forss, Anna-Maria; Bach, Christian; Mattrel, Peter

    Time-resolved chemical ionization mass spectrometry (CI-MS) has been used to investigate the velocity-dependent emission factors for benzene, toluene, the C 2-benzenes (xylenes and ethyl benzene) and nitrogen monoxide of a gasoline-driven passenger car (1.4 l, model year 1995) driven with or without catalytic exhaust gas treatment. A set of seven different driving cycles - including the European Driving Cycle (EDC), the US Urban (FTP 75) and the Highway driving cycles - with a total driving time of 12,000 s have been studied. From the obtained emission data, two sets of 15,300 and 17,200 data points which represent transient driving in the velocity range of 0-150 km h -1 and in an acceleration window of -2-3 m s -2 were explored to gain velocity-dependent emission factors. The passenger car, equipped with a regulated rhodium-platinum based three-way catalyst, showed optimal conversion efficiency (>95%) for benzene in the velocity range of 60-120 km h -1. The conversion of benzene was reduced (speed and engine load (>130 km h -1). Whereas the conversion efficiency for the class of C 2-benzenes was reduced to 10%, no net conversion could be found for toluene and benzene when driven above 130 km h -1. In contrast, the benzene and toluene emissions exceeded those of the untreated exhaust gas in the velocity range of 130-150 km h -1 by 50-92% and by 10-34%, respectively. Thus, benzene and toluene were formed across the examined three-way catalyst if the engine is operated for an extended time in a fuel-rich mode (lambda<1).

  19. Effects of fresh lubricant oils on particle emissions emitted by a modern gasoline direct injection passenger car.

    Science.gov (United States)

    Pirjola, Liisa; Karjalainen, Panu; Heikkilä, Juha; Saari, Sampo; Tzamkiozis, Theodoros; Ntziachristos, Leonidas; Kulmala, Kari; Keskinen, Jorma; Rönkkö, Topi

    2015-03-17

    Particle emissions from a modern turbocharged gasoline direct injection passenger car equipped with a three-way catalyst and an exhaust gas recirculation system were studied while the vehicle was running on low-sulfur gasoline and, consecutively, with five different lubrication oils. Exhaust particle number concentration, size distribution, and volatility were determined both at laboratory and on-road conditions. The results indicated that the choice of lubricant affected particle emissions both during the cold start and warm driving cycles. However, the contribution of engine oil depended on driving conditions being higher during acceleration and steady state driving than during deceleration. The highest emission factors were found with two oils that had the highest metal content. The results indicate that a 10% decrease in the Zn content of engine oils is linked with an 11-13% decrease to the nonvolatile particle number emissions in steady driving conditions and a 5% decrease over the New European Driving Cycle. The effect of lubricant on volatile particles was even higher, on the order of 20%.

  20. Influences of HVO and FAME on the combustion and emissions of modern passenger car diesel engines

    International Nuclear Information System (INIS)

    Stengel, Benjamin; Sadlowski, Thomas; Wichmann, Volker; Harndorf, Horst

    2014-01-01

    In the framework of this study engine tests were performed with FAME (fatty acid methyl ester) and HVO (hydrotreated vegetable oil) as straight fuels using a EURO-VI passenger car diesel engine. Standard diesel fuel (EN 590) was used as reference. To analyze the impacts of the biofuels on the combustion process the heat release rates were calculated from in-cylinder pressure measurements using a single-zone model. Furthermore emissions were measured and ECU data was recorded. Results from engine tests showed that both HVO and FAME positively affect the combustion by a decreased ignition delay due to its higher cetane number. Raw exhaust emissions of soot were clearly reduced with HVO while CO and THC emissions showed minor reductions. During FAME operation ECU control settings were shifted due to its lower heating value. FAME showed reductions of soot by 60 % which is caused by the fuel's oxygen content while NO x emissions where slightly increased. However, a fuel adapted ECU calibration could optimize, e.g., the injection timing and EGR to further reduce emissions. Tailpipe emissions were not affected by HVO and FAME as the exhaust aftertreatment systems worked similarly efficient for all three fuels.

  1. UV exposure in cars.

    Science.gov (United States)

    Moehrle, Matthias; Soballa, Martin; Korn, Manfred

    2003-08-01

    There is increasing knowledge about the hazards of solar and ultraviolet (UV) radiation to humans. Although people spend a significant time in cars, data on UV exposure during traveling are lacking. The aim of this study was to obtain basic information on personal UV exposure in cars. UV transmission of car glass samples, windscreen, side and back windows and sunroof, was determined. UV exposure of passengers was evaluated in seven German middle-class cars, fitted with three different types of car windows. UV doses were measured with open or closed windows/sunroof of Mercedes-Benz E 220 T, E 320, and S 500, and in an open convertible car (Mercedes-Benz CLK). Bacillus subtilis spore film dosimeters (Viospor) were attached to the front, vertex, cheeks, upper arms, forearms and thighs of 'adult' and 'child' dummies. UV wavelengths longer than >335 nm were transmitted through car windows, and UV irradiation >380 nm was transmitted through compound glass windscreens. There was some variation in the spectral transmission of side windows according to the type of glass. On the arms, UV exposure was 3-4% of ambient radiation when the car windows were shut, and 25-31% of ambient radiation when the windows were open. In the open convertible car, the relative personal doses reached 62% of ambient radiation. The car glass types examined offer substantial protection against short-wave UV radiation. Professional drivers should keep car windows closed on sunny days to reduce occupational UV exposure. In individuals with polymorphic light eruption, produced by long-wave UVA, additional protection by plastic films, clothes or sunscreens appears necessary.

  2. Backset and cervical retraction capacity among occupants in a modern car.

    Science.gov (United States)

    Jonsson, Bertil; Stenlund, Hans; Svensson, Mats Y; Björnstig, Ulf

    2007-03-01

    The horizontal distance between the back of the head and the frontal of the head restraint (backset) and rearward head movement relative to the torso (cervical retraction) were studied in different occupant postures and positions in a modern car. A stratified randomized population of 154 test subjects was studied in a Volvo V70 year model 2003 car, in driver, front passenger, and rear passenger position. In each position, the subjects adopted (i) a self-selected posture, (ii) a sagging posture, and (iii) an erect posture. Cervical retraction, backset, and vertical distance from the top of the head restraint to the occipital protuberance in the back of the head of the test subject were measured. These data were analyzed using repeated measures ANOVA and linear regression analysis with a significance level set to p self-selected posture, the average backset was 61 mm for drivers, 29 mm for front passengers, and 103 mm for rear passengers (p self-selected driving position. Backset was larger and cervical retraction capacity lower in the sagging posture than in the self-selected posture for occupants in all three occupant positions. Rear passengers had the largest backset values. Backset values decreased with increased age. The average cervical retraction capacity in self-selected posture was 35 mm for drivers, 30 mm for front passengers, and 33 mm for rear passengers (p < 0.001). Future design of rear-end impact protection may take these study results into account when trying to reduce backset before impact. Our results might be used for future development and use of BioRID manikins and rear-end tests in consumer rating test programs such as Euro-NCAP.

  3. How much do incentives affect car purchase? Agent-based microsimulation of consumer choice of new cars. Part 1. Model structure, simulation of bounded rationality, and model validation

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, Michel G.; Haan, Peter de [ETH Zurich, Institute for Environmental Decisions, Natural and Social Science Interface, Universitaetstr. 22, CHN J 73.2, 8092 Zurich (Switzerland)

    2009-03-15

    This article presents an agent-based microsimulation capable of forecasting the effects of policy levers that influence individual choices of new passenger cars. The fundamental decision-making units are households distinguished by sociodemographic characteristics and car ownership. A two-stage model of individual decision processes is employed. In the first stage, individual choice sets are constructed using simple, non-compensatory rules that are based on previously owned cars. Second, decision makers evaluate alternatives in their individual choice set using a multi-attributive weighting rule. The attribute weights are based on a multinomial logit model for cross-country policy analysis in European countries. Additionally, prospect theory and the notion of mental accounting are used to model the perception of monetary values. The microsimulation forecasts actual market observations with high accuracy, both on the level of aggregate market characteristics as well as on a highly resolved level of distributions of market shares. The presented approach is useful for the assessment of policies that influence individual purchase decisions of new passenger cars; it allows accounting for a highly resolved car fleet and differentiated consumer segments. As a result, the complexity of incentive schemes can be represented and detailed structural changes can be investigated. (author)

  4. How much do incentives affect car purchase? Agent-based microsimulation of consumer choice of new cars-Part I: Model structure, simulation of bounded rationality, and model validation

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, Michel G. [ETH Zurich, Institute for Environmental Decisions, Natural and Social Science Interface, Universitaetstr. 22, CHN J 73.2, 8092 Zurich (Switzerland); Haan, Peter de [ETH Zurich, Institute for Environmental Decisions, Natural and Social Science Interface, Universitaetstr. 22, CHN J 73.2, 8092 Zurich (Switzerland)], E-mail: peter.dehaan@env.ethz.ch

    2009-03-15

    This article presents an agent-based microsimulation capable of forecasting the effects of policy levers that influence individual choices of new passenger cars. The fundamental decision-making units are households distinguished by sociodemographic characteristics and car ownership. A two-stage model of individual decision processes is employed. In the first stage, individual choice sets are constructed using simple, non-compensatory rules that are based on previously owned cars. Second, decision makers evaluate alternatives in their individual choice set using a multi-attributive weighting rule. The attribute weights are based on a multinomial logit model for cross-country policy analysis in European countries. Additionally, prospect theory and the notion of mental accounting are used to model the perception of monetary values. The microsimulation forecasts actual market observations with high accuracy, both on the level of aggregate market characteristics as well as on a highly resolved level of distributions of market shares. The presented approach is useful for the assessment of policies that influence individual purchase decisions of new passenger cars; it allows accounting for a highly resolved car fleet and differentiated consumer segments. As a result, the complexity of incentive schemes can be represented and detailed structural changes can be investigated.

  5. How much do incentives affect car purchase? Agent-based microsimulation of consumer choice of new cars-Part I: Model structure, simulation of bounded rationality, and model validation

    International Nuclear Information System (INIS)

    Mueller, Michel G.; Haan, Peter de

    2009-01-01

    This article presents an agent-based microsimulation capable of forecasting the effects of policy levers that influence individual choices of new passenger cars. The fundamental decision-making units are households distinguished by sociodemographic characteristics and car ownership. A two-stage model of individual decision processes is employed. In the first stage, individual choice sets are constructed using simple, non-compensatory rules that are based on previously owned cars. Second, decision makers evaluate alternatives in their individual choice set using a multi-attributive weighting rule. The attribute weights are based on a multinomial logit model for cross-country policy analysis in European countries. Additionally, prospect theory and the notion of mental accounting are used to model the perception of monetary values. The microsimulation forecasts actual market observations with high accuracy, both on the level of aggregate market characteristics as well as on a highly resolved level of distributions of market shares. The presented approach is useful for the assessment of policies that influence individual purchase decisions of new passenger cars; it allows accounting for a highly resolved car fleet and differentiated consumer segments. As a result, the complexity of incentive schemes can be represented and detailed structural changes can be investigated

  6. 77 FR 53199 - California State Motor Vehicle Pollution Control Standards; Advanced Clean Car Program; Request...

    Science.gov (United States)

    2012-08-31

    ... cars, light-duty trucks and medium-duty passenger vehicles (and limited requirements related to heavy... ENVIRONMENTAL PROTECTION AGENCY [AMS-FRL-9724-4] California State Motor Vehicle Pollution Control Standards; Advanced Clean Car Program; Request for Waiver of Preemption; Opportunity for Public Hearing and...

  7. Modeling and simulation of cars in frontal collision

    Science.gov (United States)

    Deac, S. C.; Perescu, A.; Simoiu, D.; Nyaguly, E.; Crâştiu, I.; Bereteu, L.

    2018-01-01

    Protection of cars, mainly drivers and passengers in a collision are very important issues worldwide. Statistics given by “World Health Organization” are alarming rate of increase in the number of road accidents, most claiming with serious injury, human and material loss. For these reasons has been a continuous development of protection systems, especially car causing three quarters of all accidents. Mathematical modeling and simulation of a car behavior during a frontal collision leads to new solutions in the development of protective systems. This paper presents several structural models of a vehicle during a frontal collision and its behavior is analyzed by numerical simulation using Simulink.

  8. Pathways to Decarbonise the European Car Fleet: A Scenario Analysis Using the Backcasting Approach

    Directory of Open Access Journals (Sweden)

    Arne Höltl

    2017-12-01

    Full Text Available This paper analyses decarbonisation scenarios for the European passenger car fleet in 2050. The scenarios have been developed using the backcasting approach and aim to reduce greenhouse gas (GHG emissions of passenger cars to a level defined in the Transport White paper that is 60% below 1990 levels. Considering the emission levels of 2010, a yearly reduction of 1.7% is required in order to achieve the target. Car emissions were decomposed into the main emission factors of mobility, efficiency and carbon intensity. How these factors change over time depends on various external factors: the pace of technological improvements, the future role of cars in society’s mobility system and the priority given to decarbonising energy demand. The analysis showed that if car mobility and ownership continue to increase as expected in a ‘business as usual’ case, a share of 97% plug-in hybrid or battery electric vehicles might be required by 2050, together with a substantial decrease in greenhouse gas emission from electricity production. A transition to more advanced car technology such as automated driving, advanced batteries or lightweight materials in vehicle production would raise vehicle efficiency. Should car mobility continue at a high level, an early technology transition will be required.

  9. The effect of load and thickness variation on stress analysis of monocoque frame of electric city car using FEM

    Science.gov (United States)

    Makhrojan, Agus; Suprihadi, Agus; Budi, Sigit Setijo; Jamari, J.; Ismail, Rifky

    2017-01-01

    The electric car is transportation which growing and constantly put through improvisation vehicle design. One of the structural components of the electric car which holds a major role is a frame. The purpose of this study is to get monocoque frame design which lightweight and powerful for a city car with two passengers that was able to improve the efficiency of the battery voltage source. Monocoque frame should be able to accept the normal loads such as the weight of batteries, passenger, and body. The most important thing, monocoque frame should also be able to protect the driver and passengers in the event of a collision. Mild steel was chosen for the design because it is easy to obtain and reasonable price as well as easy to shaped for two-seater electric car. FEM (finite element method) was used to determine stress determination and rigidity of the monocoque frame when receiving a static load. The results show that the monocoque frame was still able to withstand the required loads with minimal deflection.

  10. Stress analysis on passenger deck due to modification from passenger ship to vehicle-carrying ship

    Science.gov (United States)

    Zubaydi, A.; Sujiatanti, S. H.; Hariyanto, T. R.

    2018-03-01

    Stress is a basic concept in learning about material mechanism. The main focus that needs to be brought to attention in analyzing stress is strength, which is the structural capacity to carry or distribute loads. The structural capacity not only measured by comparing the maximum stress with the material’s yield strength but also with the permissible stress required by the Indonesian Classification Bureau (BKI), which certainly makes it much safer. This final project analyzes stress in passenger deck that experiences modification due to load changes, from passenger load to vehicle one, carrying: 6-wheels truck with maximum weight of 14 tons, a passenger car with maximum weight of 3.5 tons, and a motorcycle with maximum weight of 0.4 tons. The deck structure is modelled using finite element software. The boundary conditions given to the structural model are fix and simple constraint. The load that works on this deck is the deck load which comes from the vehicles on deck with three vehicles’ arrangement plans. After that, software modelling is conducted for analysis purpose. Analysis result shows a variation of maximum stress that occurs i.e. 135 N/mm2, 133 N/mm2, and 152 N/mm2. Those maximum stresses will not affect the structure of passenger deck’s because the maximum stress that occurs indicates smaller value compared to the Indonesian Classification Bureau’s permissible stress (175 N/mm2) as well as the material’s yield strength (235 N/mm2). Thus, the structural strength of passenger deck is shown to be capable of carrying the weight of vehicles in accordance with the three vehicles’ arrangement plans.

  11. Simulation of storage performance on hydropneumatic driveline in dual hybrid hydraulic passenger car

    Directory of Open Access Journals (Sweden)

    Wasbari Faizil

    2017-01-01

    Full Text Available The charging process is one of the critical processes in the hydro-pneumatic driveline storage system. It converts the kinetic energy of the vehicle braking and coasting to the compression energy. This energy is stored in the storage device called the accumulator. The system is planned to be used on the dual hydro-pneumatic hybrid driveline and applied to a hydraulic hybrid passenger car. The aim of this paper is to find the effect of charging parameters on the storage performance through simulation. Through the storage behaviour, the desirable and optimal sizing of the accumulator can be selected. The paper emphasized on the effect of pressure elevation, pre-charge pressure, effective volume, thermal reaction and required time of the accumulator’s charging process. The circuit of charging process has been designed and simulated by using the hydraulic tool in the Automation Studio software. The simulation results were corroborated through the component specification for data rationality. Through the simulation, it was found that pre-charge pressure had a significant effect on the charging process. It determined the efficiency of the effective volume. The higher the pressure elevation, the higher the effective volume. Nevertheless, the more energy required to compress the nitrogen gas in the bladder. Besides, in term of volume displacement, higher volume displacement reduced charging time and lower the fluid temperature. The simulation had been positively highlighted the critical point in charging process which later on, benefited the sizing process in the component selection specification.

  12. Effects of low concentration biodiesel blends application on modern passenger cars. Part 2: Impact on carbonyl compound emissions

    International Nuclear Information System (INIS)

    Fontaras, Georgios; Karavalakis, Georgios; Kousoulidou, Marina; Ntziachristos, Leonidas; Bakeas, Evangelos; Stournas, Stamoulis; Samaras, Zissis

    2010-01-01

    Today in most European member states diesel contains up to 5% vol biodiesel. Since blending is expected to increase to 10% vol, the question arises, how this higher mixing ratio will affect tailpipe emissions particularly those linked to adverse health effects. This paper focuses on the impact of biodiesel on carbonyl compound emissions, attempting also to identify possible relationship between biodiesel feedstock and emissions. The blends were produced from five different feedstocks, commonly used in Europe. Measurements were conducted on a Euro 3 common-rail passenger car over various driving cycles. Results indicate that generally the use of biodiesel at low concentrations has a minor effect on carbonyl compound emissions. However, certain biodiesels resulted in significant increases while others led to decreases. Biodiesels associated with increases were those derived from rapeseed oil (approx. 200%) and palm oil (approx. 180%), with the highest average increases observed at formaldehyde and acroleine/acetone. - Biodiesel application, may increase the levels of certain pollutants such as carbonyl compounds which are associated with both environmental and health risks.

  13. Rational Formations of a Metro Train Improve Its Efficiencies of Both Traction Energy Utilization and Passenger Transport

    Directory of Open Access Journals (Sweden)

    Xuesong Feng

    2013-01-01

    Full Text Available Based on simulations of passenger transports of two representative types of metro trains in China, this study analyzes efficiencies of energy consumption and passenger transport of a metro train in the effect of its target speed, formation scale (FS (i.e., length and mass of the formation, relative traction capacity (RTC (i.e., ratio of the motoring cars to all its cars, and so forth. It is found that increasing energy cost efficiency of a metro train with decreasing its target speed is evidently accelerated with reducing its RTC below 0.50 at the expense of obviously lowering its passenger transport efficiency. Moreover, if the passenger capacity of the train is sufficiently utilized, increasing its FS for the same RTC is easy to have its passenger transport efficiency improved significantly even for a meanwhile much decreased target speed with consuming energy less intensively. Therefore, metro trains in peak hours may take comparatively big FSs, relatively high target speeds, and RTCs over 0.50 to meet usually urgent and large-scale travel demands in such time. In contrast, trains in nonpeak hours ought to have small FSs, relatively low target speeds, and RTCs smaller than 0.50 for mainly avoiding energy waste.

  14. Car stickers for 2009

    CERN Multimedia

    TS Department

    2008-01-01

    All members of the personnel holding a valid contract (except owners of cars with green or CD plates) can come to the Registration Service (Building 55, 1st floor) to obtain their 2009 car sticker, Mondays to Fridays from 7.30 a.m. to 4.00 p.m. non-stop. Please ensure you bring with you the documents relating to the vehicles(s) concerned. If you only wish to register one vehicle, you can obtain the 2009 sticker using the request form on the Web (via internet Explorer only). NB: This notice only applies to members of the personnel who obtained one or several blue car stickers for 2008. Reception and Access Control Service – TS/FM

  15. Particulates and noise exposure during bicycle, bus and car commuting: A study in three European cities.

    Science.gov (United States)

    Okokon, Enembe O; Yli-Tuomi, Tarja; Turunen, Anu W; Taimisto, Pekka; Pennanen, Arto; Vouitsis, Ilias; Samaras, Zissis; Voogt, Marita; Keuken, Menno; Lanki, Timo

    2017-04-01

    In order to curb traffic-related air pollution and its impact on the physical environment, contemporary city commuters are encouraged to shift from private car use to active or public transport modes. However, personal exposures to particulate matter (PM), black carbon and noise during commuting may be substantial. Therefore, studies comparing exposures during recommended modes of transport versus car trips are needed. We measured personal exposure to various-sized particulates, soot, and noise during commuting by bicycle, bus and car in three European cities: Helsinki in Finland, Rotterdam in the Netherlands and Thessaloniki in Greece using portable monitoring devices. We monitored commonly travelled routes in these cities. The total number of one-way trips yielding data on any of the measured parameters were 84, 72, 94 and 69 for bicycle, bus, closed-window car and open-window car modes, respectively. The highest mean PM 2.5 (85µg/m 3 ), PM 10 (131µg/m 3 ), black carbon (10.9µg/m 3 ) and noise (75dBA) levels were recorded on the bus, bus (again), open-window car and bicycle modes, respectively, all in Thessaloniki, PM and soot concentrations were generally higher during biking and taking a bus than during a drive in a a car with closed windows. Ratios of bike:car PM 10 ranged from 1.1 in Thessaloniki to 2.6 in Helsinki, while bus:car ratios ranged from in 1.0 in Rotterdam to 5.6 in Thessaloniki. Higher noise levels were mostly recorded during bicycle rides. Based on our study, active- and public-transport commuters are often at risk of higher air pollution and noise exposure than private car users. This should be taken into account in urban transportation planning. Copyright © 2017 Elsevier Inc. All rights reserved.

  16. Modelling mode choice in short trips - shifting from car to bicycle

    DEFF Research Database (Denmark)

    Halldórsdóttir, Katrín; Christensen, Linda; Jensen, Thomas Christian

    2011-01-01

    -economic variables of a representative sample of the population. The investigated sample includes 11,072 observations. The model considers five alternatives (i.e., car driver, car passenger, public transport, walk and obviously bike), for which level of service variables are calculated through assignment procedures...... relevance of the cost for short trips. Expectedly, the selection of bicycle as mode for short trips is positively related to owning a bicycle and negatively linked to owning one or more cars. Urban density has also positive correlation with the selection of sustainable transport modes....

  17. ‘We are the future’: understanding adolescents’ intentions to commute by car or bicycle as adults

    DEFF Research Database (Denmark)

    Sigurdardottir, Sigrun Birna; Kaplan, Sigal; Møller, Mette

    This study focuses on the intentions of adolescents to commute by car or bicycle as adults, as key elements towards promoting societal transition towards sustainable modes. The behavioral model is based on the theory of planned behavior combined with positive current travel experience, willingness...... passenger experience, general interest in cars, and car-ownership norms, and are negatively related to willingness to accept car restrictions and perceived lack of behavioral control; (ii) cycling intentions are positively related to positive cycling experience, willingness to accept car restrictions...

  18. Investigation of a concept for electrohydraulic power supply for future passenger car brake systems considering; Untersuchung zur Konzeption einer elektrohydraulischen Energieversorgung fuer zukuenftige Pkw-Bremssysteme

    Energy Technology Data Exchange (ETDEWEB)

    Mutschler, R.

    1999-07-01

    An electrohydraulic power supply for passenger car brake systems is presented. These systems can be classified as brake by wire. The power supply consists of a hydropneumatic accumulator, a high pressure pump and an electric drive. The components are designed considering automotive requests. A new approach to minimize hydraulic pulsations caused by a high pressure piston pump is shown. [German] Eine elektrohydraulische Energieversorgung fuer PKW-Bremssysteme wird vorgestellt. Diese Systeme koennen mit brake by wire klassifiziert werden. Die Energieversorgung besteht aus einem hydropneumatischen Speicher, einer Hochdruckpumpe und einem elektrischen Antrieb. Die Komponenten werden hinsichtlich Automobilanforderungen ausgelegt. Eine neue Methode der Minimierung hydraulischer Pulsationen, die von einer Hochdruck Kolbenpumpe verursacht werden, wird gezeigt.

  19. Passenger transport in Nigeria: Environmental and economic analysis with policy recommendations

    International Nuclear Information System (INIS)

    Gujba, H.; Mulugetta, Y.; Azapagic, A.

    2013-01-01

    This paper presents the life cycle environmental impacts and economic costs of the passenger transport sector in Nigeria for 2003–2030. Four scenarios are considered: business as usual (BAU); increased use of public transport (buses) at the expense of cars (LOWCAR) and motorcycles (LOWMC), respectively; and high economic growth with increased car ownership and decline of public transport (HICAR). The findings show that for the BAU scenario the life cycle environmental impacts double over the period, despite the assumption of increased fuel and vehicle efficiency of 35% over time. The total fuel costs at the sectoral level increase three times, from US$3.4 billion/yr in 2003 to US$9.7 billion in 2030. Increasing the use of buses would reduce the environmental impacts on average by 15–20% compared to BAU; at the same time, the total fuel costs would be 25–30% lower. If the use of cars grows much faster due to a high economic growth as in HICAR, the environmental impacts and fuel costs would increase by 16% and 26%, respectively. These results demonstrate clearly that future transport policy in Nigeria should promote and incentivise public (bus) transport as a much more environmentally and economically sustainable option than transport by cars and motorcycles. - Highlights: ► The life cycle environmental impacts of passenger transport in Nigeria estimated for 2003–2030. ► The tradeoffs between economic costs and environmental impacts discussed. ► Scenarios considered: business as usual; sustainable transport; high economic growth. ► Public transport is more sustainable than transport by cars and motorcycles. ► Ending gas flaring would improve substantially environmental, economic and social impacts

  20. Comfortable car interiors: Experiments as a basis for car interior design contributing to the pleasure of the driver and passengers

    OpenAIRE

    Kamp, I.

    2012-01-01

    One of the main challenges for car manufacturers is complying with the stringent environmental regulations without compromising driving comfort and pleasure. Reducing the overall weight of a car reduces fuel consumption and increases acceleration. However weight reduction seems in contradiction with another important aspect of car-sales; comfort. In this PhD thesis five experiments are presented proving that weight reduction and comfort improvement can go hand in hand. In these studies specif...

  1. Fiscal Measures to Reduce CO2 Emissions from New Passenger Cars

    OpenAIRE

    Cowi A/S

    2002-01-01

    Model based calculations constitute the core output of this study. The calculations assess the extent to which vehicle related taxes (mainly acquisition taxes and ownership taxes) can be effective means to reduce CO2 emissions from new cars. More specifically, the model calculations have assessed the ability of vehicle taxes to support the target to reduce average CO2 emissions from new cars down to a level of 120 g/km. This is the agreed target of the Community Strategy to reduce CO2 emissio...

  2. Heterogeneity of passenger exposure to air pollutants in public transport microenvironments

    Science.gov (United States)

    Yang, Fenhuan; Kaul, Daya; Wong, Ka Chun; Westerdahl, Dane; Sun, Li; Ho, Kin-fai; Tian, Linwei; Brimblecombe, Peter; Ning, Zhi

    2015-05-01

    Epidemiologic studies have linked human exposure to pollutants with adverse health effects. Passenger exposure in public transport systems contributes an important fraction of daily burden of air pollutants. While there is extensive literature reporting the concentrations of pollutants in public transport systems in different cities, there are few studies systematically addressing the heterogeneity of passenger exposure in different transit microenvironments, in cabins of different transit vehicles and in areas with different characteristics. The present study investigated PM2.5 (particulate matter with aerodynamic diameters smaller than 2.5 μm), black carbon (BC), ultrafine particles (UFP) and carbon monoxide (CO) pollutant concentrations in various public road transport systems in highly urbanized city of Hong Kong. Using a trolley case housing numerous portable air monitors, we conducted a total of 119 trips during the campaign. Transit microenvironments, classified as 1). busy and secondary roadside bus stops; 2). open and enclosed termini; 3). above- and under-ground Motor Rail Transport (MTR) platforms, were investigated and compared to identify the factors that may affect passenger exposures. The pollutants inside bus and MTR cabins were also investigated together with a comparison of time integrated exposure between the transit modes. Busy roadside and enclosed termini demonstrated the highest average particle concentrations while the lowest was found on the MTR platforms. Traffic-related pollutants BC, UFP and CO showed larger variations than PM2.5 across different microenvironments and areas confirming their heterogeneity in urban environments. In-cabin pollutant concentrations showed distinct patterns with BC and UFP high in diesel bus cabins and CO high in LPG bus cabins, suggesting possible self-pollution issues and/or penetration of on-road pollutants inside cabins during bus transit. The total passenger exposure along selected routes, showed bus

  3. Predicting PM10 concentration in Seoul metropolitan subway stations using artificial neural network (ANN).

    Science.gov (United States)

    Park, Sechan; Kim, Minjeong; Kim, Minhae; Namgung, Hyeong-Gyu; Kim, Ki-Tae; Cho, Kyung Hwa; Kwon, Soon-Bark

    2018-01-05

    The indoor air quality of subway systems can significantly affect the health of passengers since these systems are widely used for short-distance transit in metropolitan urban areas in many countries. The particles generated by abrasion during subway operations and the vehicle-emitted pollutants flowing in from the street in particular affect the air quality in underground subway stations. Thus the continuous monitoring of particulate matter (PM) in underground station is important to evaluate the exposure level of PM to passengers. However, it is difficult to obtain indoor PM data because the measurement systems are expensive and difficult to install and operate for significant periods of time in spaces crowded with people. In this study, we predicted the indoor PM concentration using the information of outdoor PM, the number of subway trains running, and information on ventilation operation by the artificial neural network (ANN) model. As well, we investigated the relationship between ANN's performance and the depth of underground subway station. ANN model showed a high correlation between the predicted and actual measured values and it was able to predict 67∼80% of PM at 6 subway station. In addition, we found that platform shape and depth influenced the model performance. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. Air pollution and activity during transportation by car, subway, and walking.

    Science.gov (United States)

    Morabia, Alfredo; Amstislavski, Philippe N; Mirer, Franklin E; Amstislavski, Tashia M; Eisl, Holger; Wolff, Mary S; Markowitz, Steven B

    2009-07-01

    Little evidence exists about the health risks and benefits associated with using public buses and subways rather than cars. The objective of the current study was to assess the magnitude and variance of personal exposure to particulate matter 2.5 microns or smaller (PM(2.5)) and concomitant physical activity energy expenditure (PAEE) for transportation by car, subway, or walking. Twenty nonsmoking volunteers from New York City traveled on predetermined routes by car, subway, and walking, for up to 8 hours on 3 different days, between October 2007 and February 2008. Outfitted with a personal monitor with PM(2.5) aerosol inlet, and a GPS receiver, they completed a detailed physical activity diary for each route. Both metabolic equivalent (MET) and PAEE rates (Kcal/min) were computed from GPS-derived activity durations and speeds, activity-specific METs, and measured body weight. Total PM(2.5) exposures did not differ among car, subway, and walking arms (respectively, 21.4, 30.6, and 26.5 microg/m(3) x min, p=0.19); but average MET values (respectively, 1.51, 2.03, and 2.60 Kcal/kg x hr, ptransportation.

  5. Challenges in evaluating PM concentration levels, commuting exposure, and mask efficacy in reducing PM exposure in growing, urban communities in a developing country.

    Science.gov (United States)

    Patel, Disa; Shibata, Tomoyuki; Wilson, James; Maidin, Alimin

    2016-02-01

    Particulate matter (PM) contributes to an increased risk of respiratory and cardiovascular illnesses, cancer, and preterm birth complications. This project assessed PM exposure in Eastern Indonesia's largest city, where air quality has not been comprehensively monitored. We examined the efficacy of wearing masks as an individual intervention effort to reduce in-transit PM exposures. Handheld particulate counters were used to investigate ambient air quality for spatial analysis, as well as the differences in exposure to PM2.5 and PM10 (μg/m(3)) by different transportation methods [e.g. motorcycle (n=97), pete-pete (n=53), and car (n=55); note: n=1 means 1m(3) of air sample]. Mask efficacy to reduce PM exposure was evaluated [e.g. surgical masks (n=39), bandanas (n=52), and motorcycle masks (n=39)]. A Monte Carlo simulation was used to provide a range of uncertainty in exposure assessment. Overall PM10 levels (91±124 μg/m(3)) were elevated compared to the World Health Organization (WHO)'s 24-hour air quality guideline (50 μg/m(3)). While average PM2.5 levels (9±14 μg/m(3)) were below the WHO's guideline (25 μg/m(3)), measurements up to 139 μg/m(3) were observed. Compared to cars, average motorcycle and pete-pete PM exposures were four and three times higher for PM2.5, and 13 and 10 times higher for PM10, respectively. Only surgical masks were consistent in lowering PM2.5 and PM10 (pmasks. Individual interventions can effectively reduce individual PM exposures; however, policy interventions will be needed to improve the overall air quality and create safer transportation. Copyright © 2015 Elsevier B.V. All rights reserved.

  6. Evaluation of NOx emissions of a retrofitted Euro 5 passenger car for the Horizon prize "Engine retrofit".

    Science.gov (United States)

    Giechaskiel, Barouch; Suarez-Bertoa, Ricardo; Lähde, Tero; Clairotte, Michael; Carriero, Massimo; Bonnel, Pierre; Maggiore, Maurizio

    2018-06-13

    The Horizon 2020 prize for the "Engine Retrofit for Clean Air" aims at reducing the pollution in cities by spurring the development of retrofit technology for diesel engines. A Euro 5 passenger car was retrofitted with an under-floor SCR (Selective Catalytic Reduction) for NO x catalyst in combination with a solid ammonia based dosing system as the NO x reductant. The vehicle was tested both on the road and on the chassis dynamometer under various test cycles and ambient temperatures. The NO x emissions were reduced by 350-1100 mg/km (60-85%) in the laboratory depending on the test cycle and engine conditions (cold or hot start), except at type approval conditions. The reduction for cold start urban cycles was < 75 mg/km (< 15%). The on road and laboratory tests were inline. In some high speed conditions significant increase of ammonia (NH 3 ) and nitrous oxide (N 2 O) were measured. No effect was seen on other pollutants (hydrocarbons, carbon monoxide and particles). The results of the present study show that retrofitting high emitting vehicles can significantly reduce vehicle NO x emissions and ultimately pollution in cities. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights reserved.

  7. Comfortable car interiors : Experiments as a basis for car interior design contributing to the pleasure of the driver and passengers

    NARCIS (Netherlands)

    Kamp, I.

    2012-01-01

    One of the main challenges for car manufacturers is complying with the stringent environmental regulations without compromising driving comfort and pleasure. Reducing the overall weight of a car reduces fuel consumption and increases acceleration. However weight reduction seems in contradiction with

  8. An experimental investigation of tobacco smoke pollution in cars.

    Science.gov (United States)

    Sendzik, Taryn; Fong, Geoffrey T; Travers, Mark J; Hyland, Andrew

    2009-06-01

    Tobacco smoke pollution (TSP) has been identified as a serious public health threat. Although the number of jurisdictions that prohibit smoking in public places has increased rapidly, just a few successful attempts have been made to pass similar laws prohibiting smoking in cars, where the cabin space may contribute to concentrated exposure. In particular, TSP constitutes a potentially serious health hazard to children because of prolonged exposure and their small size. The present study investigated the levels of TSP in 18 cars via the measurement of fine respirable particles (Car owners smoked a single cigarette in their cars in each of five controlled air-sampling conditions. Each condition varied on movement of the car, presence of air conditioning, open windows, and combinations of these airflow influences. Smoking just a single cigarette in a car generated extremely high average levels of PM(2.5): more than 3,800 microg/m3 in the condition with the least airflow (motionless car, windows closed). In moderate ventilation conditions (air conditioning or having the smoking driver hold the cigarette next to a half-open window), the average levels of PM(2.5) were reduced but still at significantly high levels (air conditioning = 844 microg/m3; holding cigarette next to a half-open window = 223 microg/m3). This study demonstrates that TSP in cars reaches unhealthy levels, even under realistic ventilation conditions, lending support to efforts occurring across a growing number of jurisdictions to educate people and prohibit smoking in cars in the presence of children.

  9. Investigate moped-car conflicts in China using a naturalistic driving study approach.

    Science.gov (United States)

    Glaser, Yi G; Guo, Feng; Fang, Youjia; Deng, Bing; Hankey, Jonathan

    2017-12-01

    Mopeds are a popular transportation mode in Europe and Asia. Moped-related traffic accidents account for a large proportion of crash fatalities. To develop moped-related crash countermeasures, it is important to understand the characteristics of moped-related conflicts. Naturalistic driving study data were collected in Shanghai, China from 36 car drivers. The data included 2,878h and 78,296km driven from 13,149 trips. Moped-car conflicts were identified and examined from the passenger car driver's perspective using kinematic trigger algorithms and manual video reduction. A total of 119 moped-car conflicts were identified, including 74 high g-force conflicts and 45 low g-force events. These conflicts were classified into 22 on-road configurations where both similarities and differences were found as compared to Western Countries. The majority of the conflicts occurred on secondary main roads and branch roads. Hard braking was the primary response that the car drivers made to these conflicts rather than hard steering. The identified on-road vehicle-moped conflict configurations in Shanghai, China may be attributed to the complicated traffic environment and risky behavior of moped riders. The lower prevalence of hard steering in Shanghai as compared to the United States may be due to the lower speeds at event onsets or less available steering space, e.g., less available shoulder area on Chinese urban roads. The characteristics of moped-car conflicts may impact the design of active safety countermeasures on passenger cars. The pilot data from Shanghai urban areas suggest that countermeasures developed for China may require some modifications to those developed for the United States and European countries, although this recommendation may not be conclusive given the small sample size of the study. Future studies with large samples may help better understand the characteristics of moped-car conflicts. Copyright © 2017 National Safety Council and Elsevier Ltd. All rights

  10. Traveling by Bus Instead of Car on Urban Major Roads: Safety Benefits for Vehicle Occupants, Pedestrians, and Cyclists.

    Science.gov (United States)

    Morency, Patrick; Strauss, Jillian; Pépin, Félix; Tessier, François; Grondines, Jocelyn

    2018-04-01

    Some studies have estimated fatality and injury rates for bus occupants, but data was aggregated at the country level and made no distinction between bus types. Also, injured pedestrians and cyclists, as a result of bus travel, were overlooked. We compared injury rates for car and city bus occupants on specific urban major roads, as well as the cyclist and pedestrian injuries associated with car and bus travel. We selected ten bus routes along major urban arterials (in Montreal, Canada). Passenger-kilometers traveled were estimated from vehicle counts at intersections (2002-2010) and from bus passenger counts (2008). Police accident reports (2001-2010) provided injury data for all modes. Injury rates associated with car and bus travel were calculated for vehicle occupants, pedestrians, and cyclists. Injury rate ratios were also computed. The safety benefits of bus travel, defined as the number of vehicle occupant, cyclist, and pedestrian injuries saved, were estimated for each route. Overall, for all ten routes, the ratio between car and bus occupant injury rates is 3.7 (95% CI [3.4, 4.0]). The rates of pedestrian and cyclist injuries per hundred million passenger-kilometers are also significantly greater for car travel than that for bus travel: 4.1 (95% CI [3.5, 4.9]) times greater for pedestrian injuries; 5.3 (95% CI [3.8, 7.6]) times greater for cyclist injuries. Similar results were observed for fatally and severely injured vehicle occupants, cyclists, and pedestrians. At the route level, the safety benefits of bus travel increase with the difference in injury rate associated with car and bus travel but also with the amount of passenger-kilometers by bus. Results show that city bus is a safer mode than car, for vehicle occupants but also for cyclists and pedestrians traveling along these bus routes. The safety benefits of bus travel greatly vary across urban routes; this spatial variation is most likely linked to environmental factors. Understanding the

  11. Comparison of particulate matter dose and acute heart rate variability response in cyclists, pedestrians, bus and train passengers.

    Science.gov (United States)

    Nyhan, Marguerite; McNabola, Aonghus; Misstear, Bruce

    2014-01-15

    Exposure to airborne particulate matter (PM) has been linked to cardiovascular morbidity and mortality. Heart rate variability (HRV) is a measure of the change in cardiac autonomic function, and consistent links between PM exposure and decreased HRV have been documented in studies. This study quantitatively assesses the acute relative variation of HRV with predicted PM dose in the lungs of commuters. Personal PM exposure, HR and HRV were monitored in 32 young healthy cyclists, pedestrians, bus and train passengers. Inhaled and lung deposited PM doses were determined using a numerical model of the human respiratory tract which accounted for varying ventilation rates between subjects and during commutes. Linear mixed models were used to examine air pollution dose and HRV response relationships in 122 commutes sampled. Elevated PM2.5 and PM10 inhaled and lung deposited doses were significantly (pbus (-3.2%, 95% CI: -6.4, -0.1) and train (-1.8%, -7.5, 3.8) passengers. A similar trend was observed in the case of PM2.5 lung deposited dose and results for rMSSD (the square root of the squared differences of successive normal RR intervals) followed similar trends to SDNN. Inhaled and lung deposited doses accounting for varying ventilation rates between modes, individuals and during commutes have been neglected in other studies relating PM to HRV. The findings here indicate that exercise whilst commuting has an influence on inhaled PM and PM lung deposited dose, and these were significantly associated with acute declines in HRV, especially in pedestrians and cyclists. © 2013.

  12. An Exploratory Analysis of Sound Field Characteristics using the Impulse Response in a Car Cabin

    Directory of Open Access Journals (Sweden)

    Yoshiharu Soeta

    2018-03-01

    Full Text Available Sound environments in cars are becoming quieter and receiving attention because of the prevalence of low-noise engines such as hybrid and electric engines and the manifestation of automated driving. Although the car cabin has potential as a listening space, its acoustic quality has not been examined in detail. The present study investigated sound field characteristics in the car cabin using acoustic parameters obtained by impulse response analysis. In particular, effects of the passenger position, open windows and the use of an air conditioner on acoustic parameters were investigated. The passenger position affected the sound strength at low frequencies. Rear seats, except for the rear central seat, had lower interaural correlation than the front seats, suggesting that rear seats have more diffused sound fields. The opening of windows and use of air conditioners attenuated the ratio of early- and late-arriving energy at high frequencies, suggesting a loss of clarity for music.

  13. Situations of car-to-pedestrian contact.

    Science.gov (United States)

    Matsui, Yasuhiro; Hitosugi, Masahito; Takahashi, Kunio; Doi, Tsutomu

    2013-01-01

    To reduce the severity of injuries and the number of pedestrian deaths in traffic accidents, active safety devices providing pedestrian detection are considered effective countermeasures. The features of car-to-pedestrian collisions need to be known in detail to develop such safety devices. Because information on real-world accidents is limited, this study investigated near-miss situations captured by drive recorders installed in passenger cars. We showed similarities of the contact situation between near-miss incidents and real-world fatal pedestrian accidents in Japan. We analyzed the near-miss incident data via video capturing pedestrians crossing the road in front of forward-moving cars. Using a video frame captured by a drive recorder, the time to collision (TTC) was calculated from the car velocity and the distance between the car and pedestrian at the moment that the pedestrian initially appeared. The average TTC in the cases where pedestrians were not using a pedestrian crossing was shorter than that in the cases where pedestrians were using a pedestrian crossing. The average TTC in the cases where pedestrians emerged from behind obstructions was shorter than that in the cases where drivers had unobstructed views of the pedestrians. We propose that the specifications of the safety device for pedestrian detection and automatic braking should reflect the severe approach situation for a pedestrian and car including the TTC observed for near-miss incidents.

  14. Potential health impact of switching from car to public transportation when commuting to work.

    Science.gov (United States)

    Morabia, Alfredo; Mirer, Franklin E; Amstislavski, Tashia M; Eisl, Holger M; Werbe-Fuentes, Jordan; Gorczynski, John; Goranson, Chris; Wolff, Mary S; Markowitz, Steven B

    2010-12-01

    We assessed humidity-corrected particulate matter (PM(2.5)) exposure and physical activity (using global positioning system monitors and diaries) among 18 people who commuted by car to Queens College, New York, New York, for 5 days, and then switched to commuting for the next 5 days via public transportation. The PM(2.5) differed little between car and public transportation commutes (1.41 μg/M(3)·min; P = .226). Commuting by public transportation rather than by car increased energy expenditure (+124 kcal/day; P < .001) equivalent to the loss of 1 pound of body fat per 6 weeks.

  15. Fuel efficiency of the Austrian passenger vehicle fleet-Analysis of trends in the technological profile and related impacts on CO2 emissions

    International Nuclear Information System (INIS)

    Meyer, I.; Wessely, S.

    2009-01-01

    This paper analyzes trends in the technological profile of the Austrian personnel vehicle fleet from 1990 to 2007. This includes the parameters of power, engine size and weight, which beyond the technological efficiency of the motor engine itself, are considered to be the main determinants of the fuel efficiency of the average car stock. Investigating the drivers of ever rising transport related greenhouse gas emissions is crucial in order to derive policies that strive towards more energy-efficient on-road passenger mobility. We focus on the efficacy of technological efficiency improvements in mitigating climate-relevant emissions from car use in light of shifting demand patterns towards bigger, heavier and more powerful cars. The analysis is descriptive in nature and based on a bottom-up database that was originally collated for the purpose of the present study. Technological data on car models, which includes tested fuel consumption, engine size, power and weight, is related to registered car stock and, in parts, to newly registered cars. From this, we obtain an original database of the Austrian passenger car fleet, i.e. information on consumer choice of specific car models, segregated by gasoline and diesel fuelled engines. Conclusions are derived for policies aimed at reducing the fossil fuel consumption of the moving vehicle fleet in order to contribute to a low carbon society.

  16. Connected Car: Quantified Self becomes Quantified Car

    Directory of Open Access Journals (Sweden)

    Melanie Swan

    2015-02-01

    Full Text Available The automotive industry could be facing a situation of profound change and opportunity in the coming decades. There are a number of influencing factors such as increasing urban and aging populations, self-driving cars, 3D parts printing, energy innovation, and new models of transportation service delivery (Zipcar, Uber. The connected car means that vehicles are now part of the connected world, continuously Internet-connected, generating and transmitting data, which on the one hand can be helpfully integrated into applications, like real-time traffic alerts broadcast to smartwatches, but also raises security and privacy concerns. This paper explores the automotive connected world, and describes five killer QS (Quantified Self-auto sensor applications that link quantified-self sensors (sensors that measure the personal biometrics of individuals like heart rate and automotive sensors (sensors that measure driver and passenger biometrics or quantitative automotive performance metrics like speed and braking activity. The applications are fatigue detection, real-time assistance for parking and accidents, anger management and stress reduction, keyless authentication and digital identity verification, and DIY diagnostics. These kinds of applications help to demonstrate the benefit of connected world data streams in the automotive industry and beyond where, more fundamentally for human progress, the automation of both physical and now cognitive tasks is underway.

  17. Influence of driving cycles on exhaust emissions and fuel consumption of gasoline passenger car in Bangkok.

    Science.gov (United States)

    Nutramon, Tamsanya; Supachart, Chungpaibulpatana

    2009-01-01

    The influence of different driving cycles on their exhaust emissions and fuel consumption rate of gasoline passenger car was investigated in Bangkok based on the actual measurements obtained from a test vehicle driving on a standard chassis dynamometer. A newly established Bangkok driving cycle (BDC) and the European driving cycle (EDC) which is presently adopted as the legislative cycle for testing automobiles registered in Thailand were used. The newly developed BDC is constructed using the driving characteristic data obtained from the real on-road driving tests along selected traffic routes. A method for selecting appropriate road routes for real driving tests is also introduced. Variations of keyed driving parameters of BDC with different driving cycles were discussed. The results showed that the HC and CO emission factors of BDC are almost two and four times greater than those of EDC, respectively. Although the difference in the NOx emission factor is small, the value from BDC is still greater than that of EDC by 10%. Under BDC, the test vehicle consumes fuel about 25% more than it does under EDC. All these differences are mainly attributed to the greater proportion of idle periods and higher fluctuations of vehicle speed in the BDC cycle. This result indicated that the exhausted emissions and fuel consumption of vehicles obtained from tests under the legislative modal-type driving cycle (EDC) are significantly different from those actually produced under real traffic conditions especially during peak periods.

  18. The environmental performance of current and future passenger vehicles: Life cycle assessment based on a novel scenario analysis framework

    International Nuclear Information System (INIS)

    Bauer, Christian; Hofer, Johannes; Althaus, Hans-Jörg; Del Duce, Andrea; Simons, Andrew

    2015-01-01

    Highlights: • We perform Life Cycle Assessment (LCA) of current and future passenger vehicles. • We include gasoline, diesel and natural gas as well as battery and fuel cell cars. • An integrated vehicle simulation framework guarantees consistency. • Only electric cars with “clean” electricity and H_2 allow for pollution mitigation. • Complete LCA is mandatory for environmental evaluation of vehicle technologies. - Abstract: This paper contains an evaluation of the environmental performance of a comprehensive set of current and future mid-size passenger vehicles. We present a comparative Life Cycle Assessment (LCA) based on a novel integrated vehicle simulation framework, which allows for consistency in vehicle parameter settings and consideration of future technological progress. Conventional and hybrid gasoline, diesel and natural gas cars as well as battery and fuel cell electric vehicles (BEV and FCV) are analyzed, taking into account electricity and hydrogen production chains from fossil, nuclear and renewable energy resources. Our results show that a substantial mitigation of climate change can be obtained with electric passenger vehicles, provided that non-fossil energy resources are used for electricity and hydrogen production. However, in terms of other environmental burdens such as acidification, particulate matter formation, and toxicity, BEV may in some cases and FCV are likely to perform worse than modern fossil fueled cars as a consequence of emissions along vehicle and fuel production chains. Therefore, the electrification of road transportation should be accompanied by an integration of life cycle management in vehicle manufacturing chains as well as energy and transport policies in order to counter potential environmental drawbacks.

  19. A Stochastic Route Choice Model for Car Travellers in the Copenhagen Region

    DEFF Research Database (Denmark)

    Nielsen, Otto Anker; Frederiksen, Rasmus Dyhr; Daly, A.

    2002-01-01

    The paper presents a large-scale stochastic road traffic assignment model for the Copenhagen Region. The model considers several classes of passenger cars (different trip purposes), vans and trucks, each with its own utility function on which route choices are based. The utility functions include...

  20. The Influence of Various Operation Modes on Diesel Passenger Cars CO2 Emissions

    Directory of Open Access Journals (Sweden)

    Arina Negoițescu

    2015-07-01

    Full Text Available The amount of emissions released into the atmosphere by polluting sources was significantly reduced due to the limitations introduced by the EU. Since one of the main sources affecting air quality is the car, researches regarding the influence of various factors on exhaust emissions are carried out. As CO2 is the main pollutant responsible for the greenhouse effect, the article treats the influence of vehicle load and traffic levels, running modes, the electric consumer’s utilization, and driving style on CO2 emissions for cars equipped with diesel engine. The results from the conducted study can contribute to adopt solutions in order to decrease the concentration of CO2 emissions from cars equipped with diesel engines.

  1. Closure of the flagpole car park from 1 to 5 September

    CERN Multimedia

    SMB Department

    2016-01-01

    Please note that, owing to the flag-raising ceremony to mark the accession of Romania to the status of CERN Member State, the flagpole car park will be inaccessible from the morning of 1 September 2016 until around 1 p.m. on 5 September 2016.   Users of the car park are therefore invited to remove their vehicles before 1 September and to use the Globe car park instead. ATTENTION: any vehicle left in the car park will be removed at the owners expense.

  2. A Numerical Study on Rear-spoiler of Passenger Vehicle

    OpenAIRE

    Xu-xia Hu; Eric T. T. Wong

    2011-01-01

    The simulation of external aerodynamics is one of the most challenging and important automotive CFD applications. With the rapid developments of digital computers, CFD is used as a practical tool in modern fluid dynamics research. It integrates fluid mechanics disciplines, mathematics and computer science. In this study, two different types of simulations were made, one for the flow around a simplified high speed passenger car with a rear-spoiler and the other for the flow without a rear-spoi...

  3. Car sick.

    Science.gov (United States)

    Renner, M G

    1988-01-01

    The automobile is currently seen as the most desirable mode of transportation. However, this view needs to be changed since the proliferation of the automobile worldwide is leading to the poisoning of the environment and people. In the US the number of passenger cars grew 51% between 1971-86 and in the noncommunist industrialized community that figure is 71%. The gasoline and diesel fuel used to power the overwhelming majority of cars creates a variety of problems. The pollution is estimated to have a hidden cost of US $.80/gallon. Others estimate that the pollution causes 30,000 premature deaths annually just in the US. 75% of the carbon monoxide (CO), 48% of nitrogen oxides (NO2), 13% of particulates (P), and 3% of sulfur (S) emissions come from cars in the countries of the Organization for Economic Cooperation and Development (OECD), which includes the US, Canada, Western Europe, Japan, Australia, and New Zealand. 17% of all worldwide carbon dioxide (CO2) emission comes from the production and use of fossil fuels for cars. The single biggest problem associated with cars is the photochemical smog they create in urban areas. In 1986 75 million Americans lived in areas that failed to meet national air quality standards for CO, P, and ozone (03). The only area of major improvement has been the removal of lead from gasoline. It was known to cause problems from the beginning of its use in the 1920s, but remained for 50 years because of auto and oil company pressure. Ground 03 is estimated by the US government to cost US $4 billion in annual losses, just for corn, wheat, soybeans, and peanuts. Acid rain is the other major problem associated with cars, and its damage is estimated at US $5 billion annually. Both these problems are shortterm, their effects occur immediately; the longterm disadvantage is the build up of CO2 and its contribution to the greenhouse effect. While the US is at the forefront of regulation and many other countries are modeling their emission

  4. Analysis and modelling of the pollutant emissions from European cars regarding the driving characteristics and test cycles

    Science.gov (United States)

    André, Michel; Rapone, Mario

    Within the European research project ARTEMIS, significant works have been conducted to analyse the hot emissions of pollutant from the passenger cars regarding the driving cycles and to propose modelling approaches taking into account large but heterogeneous datasets recorded in Europe. The review and analysis of a large range of test cycles enabled first the building-up of a set of contrasted cycles specifically designed for characterizing the influence of the driving conditions. These cycles were used for the measurement of the pollutants emission rates from nine passenger cars on a chassis dynamometer. Emissions measured on 30 vehicles tested on cycles adapted to their motorization (i.e., cycles for high- or low-powered cars, inducing thus a significant difference in the dynamic) were also considered for analysing the influence of the cycles and of the kinematic parameters on the hot emission rates of the regulated pollutants (CO, HC, NO x, CO 2, PM). An analyses of variance demonstrated the preponderance of the driving type (urban, rural road, motorway), of the vehicle category (fuel, emission standard) and emitting status (high/normal emitter) and thus the pertinence of analysing and modelling separately the corresponding emissions. It also demonstrated that Urban driving led systematically to high diesel emission rates and to high CO 2, HC and NO x emissions from petrol cars. Congested driving implied high CO 2 (diesel and petrol) and high diesel NO x emission. On motorway, the very high speeds generated high CO 2, while unsteady speeds induced diesel NO x and petrol CO over-emissions. A search for pertinent kinematic parameters showed that urban diesel emissions were mostly sensitive to stops and speed parameters, while petrol emissions were rather sensitive to acceleration parameters. On the motorway, diesel NO x and CO 2 emissions rates increased with the speed variability and occurrence of high speeds, while CO 2 and CO over-emission from petrol cars were

  5. SEAT BELT USE AMONG CAR USERS IN MALAYSIA

    Directory of Open Access Journals (Sweden)

    S. KULANTHAYAN

    2004-01-01

    Full Text Available The car is the second (40% most common mode of transportation in Malaysia. In terms of fatal road accidents, car drivers constitute about 9.0% and passengers 13.6% of fatalities. The major cause of car occupants' fatality in such accidents is head injuries, which consist of more than half (56.4% of the fatalities. Thus restraining the head and body, the initial position is the most important injury control strategy for car users. The use of seat belts was deemed one of the most effective ways to reduce road accident fatalities in Malaysia and consequently the mandatory seat belt law was enforced in the early seventies. Therefore, a study on factors influencing the compliance behaviour of seat belt use among cars is needed as to date no such research has been undertaken in Malaysia. A questionnaire study was carried out in Selangor, Malaysia on the compliance behaviour of car occupants in relation to seat belt use. A total of 237 respondents were interviewed and the data analysed using logistic regression method. Six variables were found to be significant at 5 percent level (p<0.05: seating position, location of travel, education level, speeding, night-time driving and enforcement. Compliance with the seat belt law was higher among drivers, educated car users, in the presence of enforcement activities, travelling in city-center areas and car users with a positive attitude towards the risks of speeding and night driving.

  6. Development and fabrication of state-of-the-art end structures for Budd M1 cars

    Science.gov (United States)

    2008-09-24

    The Volpe Center and the Federal Railroad Administration are engaged in active research aimed at improving rail vehicle crashworthiness. One component of this research is focused on improving the performance of passenger train cab cars during collisi...

  7. Crash protection of stock car racing drivers--application of biomechanical analysis of Indy car crash research.

    Science.gov (United States)

    Melvin, John W; Begeman, Paul C; Faller, Ronald K; Sicking, Dean L; McClellan, Scott B; Maynard, Edwin; Donegan, Michael W; Mallott, Annette M; Gideon, Thomas W

    2006-11-01

    Biomechanical analysis of Indy car crashes using on-board impact recorders (Melvin et al. 1998, Melvin et al. 2001) indicates that Indy car driver protection in high-energy crashes can be achieved in frontal, side, and rear crashes with severities in the range of 100 to 135 G peak deceleration and velocity changes in the range of 50 to 70 mph. These crashes were predominantly single-car impacts with the rigid concrete walls of oval tracks. This impressive level of protection was found to be due to the unique combination of a very supportive and tight-fitting cockpit-seating package, a six-point belt restraint system, and effective head padding with an extremely strong chassis that defines the seat and cockpit of a modern Indy car. In 2000 and 2001, a series of fatal crashes in stock car racing created great concern for improving the crash protection for drivers in those racecars. Unlike the Indy car, the typical racing stock car features a more spacious driver cockpit due to its resemblance to the shape of a passenger car. The typical racing seat used in stock cars did not have the same configuration or support characteristics of the Indy car seat, and five-point belt restraints were used. The tubular steel space frame chassis of a stock car also differs from an Indy car's composite chassis structure in both form and mechanical behavior. This paper describes the application of results of the biomechanical analysis of the Indy car crash studies to the unique requirements of stock car racing driver crash protection. Sled test and full-scale crash test data using both Hybrid III frontal crash anthropomorphic test devices (ATDs) and BioSID side crash ATDs for the purpose of evaluating countermeasures involving restraint systems, seats and head/neck restraints has been instrumental in guiding these developments. In addition, the development of deformable walls for oval tracks (the SAFER Barrier) is described as an adjunct to improved occupant restraint through control

  8. On-road PM2.5 pollution exposure in multiple transport microenvironments in Delhi

    Science.gov (United States)

    Goel, Rahul; Gani, Shahzad; Guttikunda, Sarath K.; Wilson, Daniel; Tiwari, Geetam

    2015-12-01

    PM2.5 pollution in Delhi averaged 150 μg/m3 from 2012 through 2014, which is 15 times higher than the World Health Organization's annual-average guideline. For this setting, we present on-road exposure of PM2.5 concentrations for 11 transport microenvironments along a fixed 8.3-km arterial route, during morning rush hour. The data collection was carried out using a portable TSI DustTrak DRX 8433 aerosol monitor, between January and May (2014). The monthly-average measured ambient concentrations varied from 130 μg/m3 to 250 μg/m3. The on-road PM2.5 concentrations exceeded the ambient measurements by an average of 40% for walking, 10% for cycle, 30% for motorised two wheeler (2W), 30% for open-windowed (OW) car, 30% for auto rickshaw, 20% for air-conditioned as well as for OW bus, 20% for bus stop, and 30% for underground metro station. On the other hand, concentrations were lower by 50% inside air-conditioned (AC) car and 20% inside the metro rail carriage. We find that the percent exceedance for open modes (cycle, auto rickshaw, 2W, OW car, and OW bus) reduces non-linearly with increasing ambient concentration. The reduction is steeper at concentrations lower than 150 μg/m3 than at higher concentrations. After accounting for air inhalation rate and speed of travel, PM2.5 mass uptake per kilometer during cycling is 9 times of AC car, the mode with the lowest exposure. At current level of concentrations, an hour of cycling in Delhi during morning rush-hour period results in PM2.5 dose which is 40% higher than an entire-day dose in cities like Tokyo, London, and New York, where ambient concentrations range from 10 to 20 μg/m3.

  9. Saturn Orbits Car Making into the Twenty-First Century. A Case Study

    Science.gov (United States)

    1993-04-01

    are adding a new automotive operating unit--Saturn--to our passenger car lines....Not since 1918, when Chevrolet joined the General Motors family, have...34landmark" for a U.S.-made car. In its comparison test with the Nissan NX 2000, the Mazda MX-3, and the Toyota Paseo, Saturn SC (sports coupe) ended in a dead...every year. 2 2 The Goliath of the group is General Motors , the world’s largest corporation. GM employs 715,000 people in 35 countries (368,000 in the

  10. On exhaust emissions from petrol-fuelled passenger cars at low ambient temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Laurikko, J. [VTT Energy, Espoo (Finland). Energy Use

    1998-11-01

    The study at hand deals with regulated and unregulated exhaust emissions from petrol-fuelled cars at low ambient temperatures with present-day or near-future exhaust after treatment systems. The subject has been investigated at VTT over a decade and this report compiles data from various sub-studies carried out between the years 1993 - 1997. Each one of them viewed different aspects of the phenomenon, like determining the low-temperature response of today`s new cars employing three-way catalytic converters or assessing the long-term durability and the influence of vehicle mileage upon the low-temperature emissions performance. Within these studies, together more than 120 cars of model years from 1990 to 1997 have been tested. Most of them were normal, in-service vehicles with total mileages differing between only a few thousand kilometres for new cars up to 80,000 km or even more for the in-use vehicles. Both the US FTP75 and the European test cycle have been employed, and the ambient temperatures ranged from the baseline (+22 deg C) down to +- O deg C, -7 deg C and in some cases even to -20 deg C. The studies attested that new cars having today`s advanced emissions control systems produced fairly low levels of emissions when tested in conditions designated in the regulations that are the basis of the current new-vehicle certification. However, this performance was not necessarily attained at ambient temperatures that were below the normative range. Fairly widespread response was recorded, and cars having almost equal emissions output at baseline could produce largely deviating outcomes in low-temperature conditions. On average, CO and HC emissions increased by a factor of five to 10, depending on the ambient temperature and vehicle type. However, emissions of NO{sub x} were largely unaffected. Apart from these regulated emissions, many unregulated species were also determined, either by using traditional sampling and chromatography methods or on-line, employing

  11. Analysis of potential diverted of passenger car to the new toll road (case study: Cileunyi - Sumedang, West Java)

    Science.gov (United States)

    Prahara, Eduardi; Suangga, Made; Lutfi Ansori, Ahmad

    2017-12-01

    This study aims to determine of potential of passenger car divert from national road to on-construction Cisumdawu Toll Road. The study was conducted by traffic count survey and followed by a roadside interview survey. Stated Preference method was used in order to analyse trip forecasting value. Mode choice model of new trip mode plans (Cisumdawu Toll Road) and current intercity road for Cileunyi - Sumedang is (UJT -UJR ) = 0.1079-0.507726x 1-0.8953764x 2, while Sumedang - Cileunyi is (UJT -UJR ) = 0.0790-0.301341x 1-0.548446x 2. Multiple linear regression analysis was used to obtain the forecasting of private vehicle that diverts to the new toll road (Cisumdawu Toll Road). Trip characteristics such as trip origin and destination, types of trips, occupations, salary, and others become a motive for respondents to choose a new trip mode. Results of the new trip mode forecasting that prefer to divert to the toll road in terms of the value of cost and time for Cileunyi - Sumedang are 74.11% and 86.62% respectively, while for Sumedang - Cileunyi are 69.60% and 76.48% respectively. These results are relatively high compare to toll planning document. The impact of this results can be determined such as lower overall fuel consumption, lower pollution and more important is the maintenance cost of national road will be decrease.

  12. Analysis of WBV on standing and seated passengers during off-peak operation in KL monorail

    Science.gov (United States)

    Hasnan, K.; Bakhsh, Q.; Ahmed, A.; Ali, D.; Jamali, A. R.

    2018-03-01

    In this study, the Whole-Body Vibration (WBV) was analyzed on the standing and seated passenger during off-peak operating hours when train was on the track. The experiments were conducted on two car train at one constant location (bogie-1, which is near to driver’s cabin) during downward direction from KL sentral station towards Titiwangsa station. The aim of this study was to analyze that, in which posture of passenger’s exposures the maximum level of WBV. Since, one passenger was performed the whole journey in standing posture whereas, the other passenger was in seated posture. The result obtained from experiments for the RMS accelerations (Arms), maximum acceleration (Amax) and minimum acceleration (Amin) during the trip. As per standard ISO 2631-1, the daily vibration exposure (A8), Vibration Dose value (VDV) and Crest Factor (CF) of this trip for both standing and sitting orientations were calculated. Results shows that the seated passenger was exposed to longer periods of continuous vibration as compared to the standing passenger. Whereas, the Vibration Dose value (VDV) value was greater than the action value as per ISO 2631-1 and within the limit values. The study concluded that whole body vibration transmitted towards both passengers either standing or seated during their journey. But in overall results comparison of both orientations, the seated passengers gained higher vibration than the standing one.

  13. Data-driven analysis of the effectiveness of evaporative emissions control systems of passenger cars in real world use condition: Time and spatial mapping

    Science.gov (United States)

    De Gennaro, Michele; Paffumi, Elena; Martini, Giorgio

    2016-03-01

    This paper assesses the effectiveness of the evaporative emissions control systems of European passenger cars on the basis of real-world activity data. The study relies on two large datasets of driving patterns from conventional fuel vehicles collected by means of on-board GPS systems, consisting of 4.5 million trips and parking events recorded by monitoring 28,000 vehicles over one month. Real world evaporative emissions are estimated using a model that associates a carbon canister desorption event to each trip and a fuel vapour generation event to each parking. The mass of volatile organic compounds released into the air is calculated taking into account the hot-soak, permeation and breathing emission mechanisms. The analysis is based on 36 scenarios, defined by varying the climate conditions, the fuel vapour pressure, the tank material, the tank headspace volume, the purging volume flow rate and the mass of the activated carbon contained in the canister. The results show that in May 4 out of the 18 scenarios considered for Modena and 6 out of the 18 scenarios considered for Firenze lead to evaporative emissions values above the current type approval limit (i.e. 2 [g/day] per vehicle). In July, these numbers increase to 10 out of the 18 scenarios for Modena and to 12 out of the 18 scenarios for Firenze. Looking at the fleet distribution a share of approximately 20% of the fleet is characterised by evaporative emissions higher than the limit in May, increasing to 48% in July, with a peak value of 98%. The emission peak value is estimated to be approximately 4 [g/day] in May and 8 [g/day] in July, while the time-dependent results show emission rates up to nearly 15 [g/s] in Modena and 30 [g/s] in Firenze, with a respective cumulative value in July up to 0.4 and 0.8 tons of VOCs per day. The space-dependent results show a value of the emissions in July of approximately 4-to-8 [kg/km2/day] in the city areas. These results confirm previous findings from the authors

  14. Measuring Product Prices under Conditions of Quality Change: The Case of Passenger Cars in Greece.

    OpenAIRE

    Bitros, George C; Panas, Epaminondas E

    1988-01-01

    The envelope curve of the bid functions for car characteristics in Greece is used to analyze the relationship between nominal and quality-adjusted car prices for 1965-85. It is estimated using the Box-Cox flexible functional form technique in a modification of S. Rosen's hedonic price model. The authors find that quality-adjusted prices of imports from West Germany, France, Italy, and Japan decline d from 1965 to 1970 and increased continuously thereafter; the quality of cars from France, Ita...

  15. "Good Passengers and Not Good Passengers:" Adolescent Drivers' Perceptions About Inattention and Peer Passengers.

    Science.gov (United States)

    McDonald, Catherine C; Sommers, Marilyn S

    The purpose of this qualitative focus group elicitation research study was to explore teen driver perceptions of peer passengers and driver inattention. We utilized focus groups for data collection and content analysis to analyze the data, both of which were guided by the theory of planned behavior. We conducted 7 focus groups with 30 teens, ages 16-18, licensed for ≤1year to examine attitudes, perceived behavioral control, and norms related to driving inattention and peer passengers. The sample was 50% male, mean age 17.39 (SD 0.52) with mean length of licensure 173.7days (SD 109.2). Three themes emerged: 1) "Good and not good" passengers; 2) Passengers and technology as harmful and helpful; and 3) The driver is in charge. While passengers can be a source of distraction, our participants also identified passenger behaviors that reduced risk, such as assistance with technology and guidance for directions. An understanding of teens' perceptions of peer passengers can contribute to the development of effective interventions targeting teen driver inattention. Nurses are well-positioned to contribute to these teen crash prevention efforts. Copyright © 2016 Elsevier Inc. All rights reserved.

  16. Effects of vehicle ventilation system, fuel type, and in-cabin smoking on the concentration of toluene and ethylbenzene in Pride cars

    Directory of Open Access Journals (Sweden)

    Masoud Rismanchian

    2013-01-01

    Conclusion: The ventilation condition, fuel type, and in-cabin smoking were not significantly impressive on the toluene and ethylbenzene concentrations inside the cars. However, simultaneous usage of the vehicle ventilation system and natural ventilation (windows could lead to little decrease in toluene concentration levels inside the car, while smoking consumption by passengers can increase them.

  17. Tendencies in the selection of materials for passenger cars from the viewpoint of the development of sport cars

    Energy Technology Data Exchange (ETDEWEB)

    Bott, H

    1981-05-18

    Aluminium as a substitute material for steel is discussed. A short discussion of glass fiber reinforced plastics and polyurethane is given. Car weights, components, and relevant construction materials are discussed. The outlook for tendencies and developments is described.

  18. 78 FR 19364 - Notice of Receipt of Petition for Decision That Nonconforming 1992-1994 BMW 3-Series Passenger...

    Science.gov (United States)

    2013-03-29

    ... Braking Effect, 103 Windshield Defrosting and Defogging Systems, 104 Windshield Wiping and Washing Systems... in the proper manner. The petitioner states that the automatic restraint system in the non-U.S... Passenger Cars are Eligible for Importation AGENCY: National Highway Traffic Safety Administration, DOT...

  19. Vehicle attributes constraining present electric car applicability in the fleet market

    Energy Technology Data Exchange (ETDEWEB)

    Wagner, J R

    1979-12-01

    One strategy for reducing petroleum imports is to use electric cars in place of conventional vehicles. This paper examines obstacles which electric cars are likely to encounter in attempting to penetrate a key segment of the passenger car market, namely, the fleet market. A fleet is here defined as a group of cars operated by a corporation or a government agency. The primary data source is a questionnaire that was distributed to fleet operators by the Bobit Publishing Company in the summer of 1977. Six sectors of the fleet market were sampled: police, state and local government, utilities, taxi, rental, and business. The questionnaire was specifically designed to uncover factors limiting market penetration of unconventional vehicles, although no attempt was made to determine price elasticities. Emphasis is on vehicle attributes that are readily quantifiable and relatively projectable, including seating capacity, range, battery recharging characteristics, availability of power options, and ability to use interstate highways.

  20. 78 FR 75442 - Emergency Order Under 49 U.S.C. 20104 Establishing Requirements for Controlling Passenger Train...

    Science.gov (United States)

    2013-12-11

    ... in Spuyten Duyvil, Bronx, New York.\\1\\ The train consisted of seven passenger coach cars, including a.../2013/R-13-17.pdf . July 18--CSX Transportation, Inc., Freight Train Derailment A third accident occurred on July 18, 2013, when a CSX Transportation, Inc. freight train derailed while traveling over...

  1. Mechanical properties of hybrid kenaf/glass reinforced epoxy composite for passenger car bumper beam

    International Nuclear Information System (INIS)

    Davoodi, M.M.; Sapuan, S.M.; Ahmad, D.; Ali, Aidy; Khalina, A.; Jonoobi, Mehdi

    2010-01-01

    It is estimated that the annual world car production rate will reach 76 million vehicles per year by 2020. New regulations such as the EU End of Life Vehicles (ELV) regulations are forcing car manufacturers to consider the environmental impact of their production and possibly shift from the use of synthetic materials to the use of agro-based materials. Poor mechanical properties and certain manufacturing limitations currently limit the use of agro-based materials to non-structural and semi-structural automotive components. The hybridization of natural fiber with glass fiber provides a method to improve the mechanical properties over natural fibers alone. This research is focused on a hybrid of kenaf/glass fiber to enhance the desired mechanical properties for car bumper beams as automotive structural components with modified sheet molding compound (SMC). A specimen without any modifier is tested and compared with a typical bumper beam material called glass mat thermoplastic (GMT). The results indicate that some mechanical properties such as tensile strength, Young's modulus, flexural strength and flexural modulus are similar to GMT, but impact strength is still low, and shows the potential for utilization of hybrid natural fiber in some car structural components such as bumper beams.

  2. [Determining the car driver's position at the moment of the frontal crash with a moving KAMAZ truck].

    Science.gov (United States)

    Gusarov, A A; Fetisov, V A; Smirenin, S A

    2016-01-01

    This article is designed to report the results of the comprehensive forensic medical and autotechnical expertise for determining the positions of the driver and the first seat passenger of the GAS-3110 car at the moment of the frontal crash with a KAMAZ-5312 truck. The comparative analysis of the injuries in two subjects one of whom died as a result of the given accident made it possible to conclude that he had occupied the driver's seat in the car. The differential diagnosis was based on the peculiarities of the injuries to the upper extremities with the predominance of the most severe wounds at the right side of the body. Also taken into consideration were the specific conditions of the given frontal collision, design of the GAS-3110 passenger compartment, winter season, night time, and possible neglect of the passive safety means, etc.

  3. Mode, load, and specific climate impact from passenger trips.

    Science.gov (United States)

    Borken-Kleefeld, Jens; Fuglestvedt, Jan; Berntsen, Terje

    2013-07-16

    The climate impact from a long-distance trip can easily vary by a factor of 10 per passenger depending on mode choice, vehicle efficiency, and occupancy. In this paper we compare the specific climate impact of long-distance car travel with coach, train, or air trips. We account for both, CO2 emissions and short-lived climate forcers. This particularly affects the ranking of aircraft's climate impact relative to other modes. We calculate the specific impact for the Global Warming Potential and the Global Temperature Change Potential, considering time horizons between 20 and 100 years, and compare with results accounting only for CO2 emissions. The car's fuel efficiency and occupancy are central whether the impact from a trip is as high as from air travel or as low as from train travel. These results can be used for carbon-offsetting schemes, mode choice and transportation planning for climate mitigation.

  4. Content analysis of television advertising for cars and minivans: 1983-1998.

    Science.gov (United States)

    Ferguson, Susan A; Hardy, Andrew P; Williams, Allan F

    2003-11-01

    Very little systematic information is available about the predominant advertising themes automobile manufacturers have depicted over the years. The goal of the present study was to analyze television vehicle advertising to understand how cars and passenger vans are being portrayed in the media and how this has changed over time. A virtually complete sample (561) of car and passenger van advertisements from 1998, and a sample of advertisements from 1983 (98), 1988 (96), and 1993 (95), was analyzed for content. Performance, most often exemplified as speed, power, and maneuverability, was the primary theme in 17% of advertisements in 1998 and was depicted in half of all advertisements. Performance was also the most frequent theme over time. Sales incentives also was a popular theme in each year studied, and was predominant in 1993. Safety was mentioned infrequently, except in 1993; a time when manufacturers were competing to install airbags in their vehicles. A focus on vehicle performance in advertising that does not depict the potential negative consequences can have the deleterious effects of glamorizing and legitimizing high-speed travel. Furthermore, manufacturers are missing an opportunity to promote vehicle safety, a feature that consumers have indicated is very important to them.

  5. The risk of whiplash-induced medical impairment in rear-end impacts for males and females in driver seat compared to front passenger seat

    Directory of Open Access Journals (Sweden)

    Bertil Jonsson

    2013-07-01

    Females had a relative risk of medical impairment of 3.1 compared to men after adjustment for the average increased risk in the driver position. The driver position had a doubled relative risk compared to the front passenger position. As a conclusion it may be of value to take risk differences between male and female occupants and between driver and front passenger positions into account in future automotive car and seat construction.

  6. “Good passengers and not good passengers:” Adolescent drivers’ perceptions about inattention and peer passengers

    Science.gov (United States)

    Sommers, Marilyn S.

    2016-01-01

    Purpose The purpose of this qualitative focus group elicitation research study was to explore teen driver perceptions of peer passengers and driver inattention. Design & Methods We utilized focus groups for data collection and content analysis to analyze the data, both of which were guided by the Theory of Planned Behavior. We conducted 7 focus groups with 30 teens, ages 16–18, licensed for ≤1 year to examine attitudes, perceived behavioral control, and norms related to driving inattention and peer passengers. Results The sample was 50% male, mean age 17.39 (sd 0.52) with mean length of licensure 173.7 days (sd 109.2). Three themes emerged: 1) “Good and not good” passengers; 2) Passengers and technology as harmful and helpful; and 3) The driver is in charge. Conclusions While passengers can be a source of distraction, our participants also identified passenger behaviors that reduced risk, such as assistance with technology and guidance for directions. Practical Implications An understanding of teens’ perceptions of peer passengers can contribute to the development of effective interventions targeting teen driver inattention. Nurses are well-positioned to contribute to these teen crash prevention efforts. PMID:27496828

  7. Concept of Seikan car train; Yuro tunnel ni manabu Seikan car train koso (rail ni doroteki kino wo)

    Energy Technology Data Exchange (ETDEWEB)

    Hirama, H.

    1997-08-15

    This paper summarizes an idea of operating a car train in the Seikan tunnel. Advantages expected from realization of this idea include assurance of mass transportation, enhancement in safety, reduction of transportation time, completion of a nationwide traffic network, and reduction of the transportation cost. A total traffic amount as sought from quantity of cargoes and number of passengers is estimated to be about 400 cars a day, and the number of trains to be operated assuming a car loading rate at 50% would be 28 trains a day. According to the profitability of this operation derived by using as calculation bases the fare revenue, expenditures and depreciation, the operation would turn into black ink in five years, clearing cumulative deficits in 17 years. In order to realize this operation, it is a prerequisite that the regulation on limitation of vehicle size (maximum width and height of vehicles) be mitigated as lax as in Eurotunnel. In addition, introduction of self-running freight cars and improvement of access roads will be necessary. Estimated economic effects may include time saving profit of 500 million yen annually, tax revenue effect of 200 million yen annually, and production inducing effect of 1.9 billion yen annually. Other expected effects may include employment effect, improvement in information transmitting function, and acceleration of different projects. 3 figs., 1 tab.

  8. Recent evidence concerning higher NO x emissions from passenger cars and light duty vehicles

    Science.gov (United States)

    Carslaw, David C.; Beevers, Sean D.; Tate, James E.; Westmoreland, Emily J.; Williams, Martin L.

    2011-12-01

    Ambient trends in nitrogen oxides (NO x) and nitrogen dioxide (NO 2) for many air pollution monitoring sites in European cities have stabilised in recent years. The lack of a decrease in the concentration of NO x and in particular NO 2 is of concern given European air quality standards are set in law. The lack of decrease in the concentration of NO x and NO 2 is also in clear disagreement with emission inventory estimates and projections. This work undertakes a comprehensive analysis of recent vehicle emissions remote sensing data from seven urban locations across the UK. The large sample size of 84,269 vehicles was carefully cross-referenced to a detailed and comprehensive database of vehicle information. We find that there are significant discrepancies between current UK/European estimates of NO x emissions and those derived from the remote sensing data for several important classes of vehicle. In the case of light duty diesel vehicles it is found that NO x emissions have changed little over 20 years or so over a period when the proportion of directly emitted NO 2 has increased substantially. For diesel cars it is found that absolute emissions of NO x are higher across all legislative classes than suggested by UK and other European emission inventories. Moreover, the analysis shows that more recent technology diesel cars (Euro 3-5) have clear increasing NO x emissions as a function of Vehicle Specific Power, which is absent for older technology vehicles. Under higher engine loads, these newer model diesel cars have a NO x/CO 2 ratio twice that of older model cars, which may be related to the increased use of turbo-charging. Current emissions of NO x from early technology catalyst-equipped petrol cars (Euro 1/2) were also found to be higher than emission inventory estimates - and comparable with NO x emissions from diesel cars. For heavy duty vehicles, it is found that NO x emissions were relatively stable until the introduction of Euro IV technology when

  9. Air quality and passenger comfort in an air-conditioned bus micro-environment.

    Science.gov (United States)

    Zhu, Xiaoxuan; Lei, Li; Wang, Xingshen; Zhang, Yinghui

    2018-04-12

    In this study, passenger comfort and the air pollution status of the micro-environmental conditions in an air-conditioned bus were investigated through questionnaires, field measurements, and a numerical simulation. As a subjective analysis, passengers' perceptions of indoor environmental quality and comfort levels were determined from questionnaires. As an objective analysis, a numerical simulation was conducted using a discrete phase model to determine the diffusion and distribution of pollutants, including particulate matter with a diameter air quality and dissatisfactory thermal comfort conditions in Jinan's air-conditioned bus system. To solve these problems, three scenarios (schemes A, B, C) were designed to alter the ventilation parameters. According to the results of an improved simulation of these scenarios, reducing or adding air outputs would shorten the time taken to reach steady-state conditions and weaken the airflow or lower the temperature in the cabin. The airflow pathway was closely related to the layout of the air conditioning. Scheme B lowered the temperature by 0.4 K and reduced the airflow by 0.01 m/s, while scheme C reduced the volume concentration of PM 10 to 150 μg/m 3 . Changing the air supply angle could further improve the airflow and reduce the concentration of PM 10 . With regard to the perception of airflow and thermal comfort, the scheme with an airflow provided by a 60° nozzle was considered better, and the concentration of PM 10 was reduced to 130 μg/m 3 .

  10. COMPUTATIONAL FLUID DYNAMICS INVESTIGATION ON THE USE OF HEAT SHIELDS FOR THERMAL MANAGEMENT IN A CAR UNDERHOOD

    Directory of Open Access Journals (Sweden)

    S.Y. Lam

    2012-12-01

    Full Text Available Temperature variations inside a car underhood are largely controlled by the heat originating from the engine block and the exhaust manifold. Excessive temperatures in the underhood can lead to the faster deterioration of engine components and may affect the thermal comfort level inside the passenger cabin. This paper presents computational fluid dynamics investigations to assess the performance of a heat shield in lowering the peak temperature of the engine components and firewall in the underhood region of a typical passenger car. The simulation used the finite volume method with the standard k-ε turbulence model and an isothermal model for the heat transfer calculations. The results show that the heat shield managed to reduce the peak temperature of the engine components and firewall by insulating the intense heat from the engine block and exhaust and regulating the airflow inside the underhood region.

  11. A comparison of contributing factors between alcohol related single vehicle motorcycle and car crashes.

    Science.gov (United States)

    Maistros, Alexander; Schneider, William H; Savolainen, Peter T

    2014-06-01

    Alcohol related crashes have accounted for approximately 35% of fatal crashes per year since 1994 nationwide, with approximately 30% involving impairment over the legal blood alcohol content limit of 0.08%. Educational campaigns and law enforcement efforts are two components of multi-faceted programs aimed toward reducing impaired driving. It is crucial that further research be conducted to guide the implementation of enforcement and educational programs. This research attempts to provide such guidance by examining differences in alcohol-involved crashes involving motorcycles and passenger cars. Prior safety research has shown that motorcyclists follow a significantly different culture than the average passenger car operator. These cultural differences may be reflected by differences in the contributing factors affecting crashes and the severity of the resulting injuries sustained by the driver or motorcyclist. This research is focused on single-vehicle crashes only, in order to isolate modal effects from the contribution of additional vehicles. The crash data provided for this study are from the Ohio Department of Public Safety from 2009 through 2012. The injury severity data are analysed through the development of two mixed logit models, one for motorcyclists and one for passenger car drivers. The models quantify the effects of various factors, including horizontal curves, speeds, seatbelt use, and helmet use, which indicate that the required motor skills and balance needed for proper motorcycle operation compounded with a lack of mechanical protection make motorcyclists more prone to severe injuries, particularly on curves and in collisions with roadside objects. The findings of this study have been incorporated into combined motorcycle and sober driving educational safety campaigns. The results have shown to be favorable in supporting national campaign messages with local justification and backing. Copyright © 2014 Elsevier Ltd. All rights reserved.

  12. Modeling real-world fuel consumption and carbon dioxide emissions with high resolution for light-duty passenger vehicles in a traffic populated city

    International Nuclear Information System (INIS)

    Zhang, Shaojun; Wu, Ye; Un, Puikei; Fu, Lixin; Hao, Jiming

    2016-01-01

    Modeling fuel consumption of light-duty passenger vehicles has created substantial concerns due to the uncertainty from real-world operating conditions. Macao is world-renowned for its tourism industry and high population density. An empirical model is developed to estimate real-world fuel consumption and carbon dioxide emissions for gasoline-powered light-duty passenger vehicles in Macao by considering local fleet configuration and operating conditions. Thanks to increasingly stringent fuel consumption limits in vehicle manufacturing countries, estimated type-approval fuel consumption for light-duty passenger vehicles in Macao by model year was reduced from 7.4 L/100 km in 1995 to 5.9 L/100 km in 2012, although a significant upsizing trend has considerably offset potential energy-saving benefit. However, lower driving speed and the air-conditioning usage tend to raise fleet-average fuel consumption and carbon dioxide emission factors, which are estimated to be 10.1 L/100 km and 240 g/km in 2010. Fleet-total fuel consumption and carbon dioxide emissions are modeled through registered vehicle population-based and link-level traffic demand approaches and the results satisfactorily coincide with the historical record of fuel sales in Macao. Temporal and spatial variations in fuel consumption and carbon dioxide emissions from light-duty passenger vehicles further highlight the importance of effective traffic management in congested areas of Macao. - Highlights: • A fuel consumption model is developed for Macao's light-duty passenger cars. • Increased vehicle size partially offset energy benefit from tightened fuel consumption standard. • Lower speed and use of air-conditioning greatly increase fuel use of Macao light-duty passenger cars. • A high resolution inventory of fuel use and carbon dioxide emissions is built with link-level traffic data. • Policy suggestions are provided to mitigate fuel use in a traffic populated city.

  13. Fleet-Car Market PENetration Simulator: CPEN user's guide

    Energy Technology Data Exchange (ETDEWEB)

    Weil, R.

    1980-08-01

    The purpose of this manual is to assist prospective users in the understanding and execution of Fleet-Car Market PENetration Simulator (CPEN). CPEN is an interactive FORTRAN program whose purpose is to produce estimates of fleet-market-penetration rates of alternative passenger cars that can be described in terms of specific physical and economic attributes. The data were derived from questionnaires distributed to fleet operators affiliated with National Association of Fleet Administrators (NAFA). Besides the NAFA data, CPEN uses 48 variables that are interactively inserted. Complete data-input descriptions are included in the manual along with algorithm and application flowcharts. Examples of complete successful simulator runs are included for alternative program paths. A listing of the computer program and a glossary for CPEN are included.

  14. Experimental and numerical study of back-cooling car-seat system using embedded heat pipes to improve passenger’s comfort

    International Nuclear Information System (INIS)

    Hatoum, Omar; Ghaddar, Nesreen; Ghali, Kamel; Ismail, Nagham

    2017-01-01

    Graphical abstract: Heat pipe assembly (a) with the insulation layer (b) without the insulation layer; and (c) thermal manikin test on the heat pipe chair. - Highlights: • A new back cooling system for a car seat using embedded heat pipes was modeled numerically. • The heat-pipe seat model was experimentally validated using heated thermal manikin. • An integrated heat pipe model and bio-heat model was used to predict local thermal comfort. • The heat pipe system reduced the back skin temperature by 1 °C compared to seat without heat pipes. • The heat pipe system increased the overall thermal comfort of the passenger by 30%. - Abstract: This work develops a back-cooling system for a car seat using seat embedded heat pipes to improve passenger comfort. The heat pipe system utilizes the temperature difference between the passenger back and the car cabin air to remove heat from the human body and enhance the comfort state. The developed seat heat-pipe model was validated experimentally using a thermal manikin with controlled constant skin temperature mode in a climatic chamber. Good agreement was found between the measured and the numerically predicted values of base panel temperature. By integrating the validated heat pipe with a bio-heat model, the back segmental skin temperature as well as the overall thermal comfort was predicted and compared with the conventional seat case without the heat pipe system. The heat pipes were able to reduce the skin temperature by 1 °C and to increase the overall thermal comfort of the body by 30%. In addition, a parametric study was performed to determine the optimal number of heat pipes that ensure the thermal comfort of the passenger.

  15. Behavioural Models for Route Choice of Passengers in Multimodal Public Transport Networks

    DEFF Research Database (Denmark)

    Anderson, Marie Karen

    in the estimation of route choice models of public transport users based upon observed choices. Public transport route choice models have not benefitted from the same technological enhancements as car models because of the necessity (i) to collect additional information concerning lines and transfers, and (ii...... modes, public transport modes, lines, transfers, egress modes) is large. This thesis proposes a doubly stochastic approach for generating alternative routes that are relevant to travellers, since the method allows accounting for both perceived costs of the network elements and heterogeneity......The subject of this thesis is behavioural models for route choice of passengers in multimodal public transport networks. While research in sustainable transport has dedicated much attention toward the determinants of choice between car and sustainable travel options, it has devoted less attention...

  16. Technologies, Multitasking, and Driving: Attending to and Preparing for a Mobile Phone Conversation in a Car

    Science.gov (United States)

    Haddington, Pentti; Rauniomaa, Mirka

    2011-01-01

    This article investigates mobile phone calls initiated or received by drivers and passengers in cars and focuses on the participants' actions before the telephone conversation proper. Drawing on video-recorded data of real driving situations, and building on conversation analysis and multimodal interaction analysis, this article discusses how…

  17. The influence of various pressures in pneumatic tyre on braking process of car with anti-lock braking system

    OpenAIRE

    Damian HADRYŚ; Tomasz WĘGRZYN; Michał MIROS

    2008-01-01

    In this article has been presented the influence of various pressures inpneumatic tyre of passenger car Fiat Panda 1.3 JTD with anti-lock braking system on chosen parameters of braking process: course of braking deceleration, maximum value of deceleration, braking distances.

  18. Urban passenger transport energy saving and emission reduction potential: A case study for Tianjin, China

    International Nuclear Information System (INIS)

    Peng, Binbin; Du, Huibin; Ma, Shoufeng; Fan, Ying; Broadstock, David C.

    2015-01-01

    Highlights: • Potential to reduce urban passenger transport is projected between 2010 and 2040. • Four scenarios reflecting different policy mixes are considered. • The potential for energy conservation and emission reductions are obtained. • Vehicle population regulation is most effective in energy saving and reducing overall GHG. • Emission standards are the most effective measure to reduce pollutant emissions. - Abstract: With rapid growth of the vehicle population, urban passenger transport in China is largely responsible for increases in energy consumption, greenhouse gas (GHG) emissions, and also atmospheric pollutants (NO x , CO, HC, PM). In this paper, we first develop an urban passenger transport energy saving and emission reduction potential evaluation model using the “Long Range Energy Alternatives Planning (LEAP)” tool; and then take Tianjin city as an empirical case to evaluate the reduction potential of final energy consumption, GHG emissions and pollutants emissions of Tianjin’s urban passenger transport sector between 2010 and 2040 under four scenarios, i.e. BAU (business as usual) scenario, PP (the 12th five-year plan policy) scenario, CP (comprehensive policy) scenario and HP (hybrid policy of PP and CP) scenario. The results show that due to the public transport promotion, energy consumption and CO 2 emissions in 2040 can be reduced by 22% and 22.6% in the PP scenario, compared to BAU. The largest reductions in energy consumption, CO 2 and atmospheric pollutants emissions can be achieved under CP scenario, in which vehicle population regulation is the most effective to be implemented. Emissions standard regulation is the most effective measure to reduce atmospheric pollutant emissions in all the scenarios and green energy promotion is especially effective to reduce NO x and PM

  19. Flame spread and smoke temperature of full-scale fire test of car fire

    Directory of Open Access Journals (Sweden)

    Dayan Li

    2017-09-01

    Full Text Available Full-scale experiments using two 4-door sedan passenger cars, placed side by side in the reverse direction, were carried out to establish the burning behavior and describe the spread of fire to adjacent car. The temperature was measured by thermocouples. Radiant heat flux was measured with heat flux gauge placed at a distance of 5 m, at the right side of the car. Four cameras were placed inside the car and in the fire test room recording burning behavior during the test. Engine compartment was ignited by a sponge dipped with little gasoline. During the experiment, the ignition was initiated in the engine compartment of car I and approximately 20 min were enough time for fire to spread into the second car. Fully-developed burning of two cars occurred at 29 min. It was observed that the flame spread through car roof faster than through the bottom of car compartment. The fire followed a slow rate spread from engine compartment to car cab. The temperature inside the car peaked at the point of 900 °C. The peak smoke temperatures at every location were measured at the range of 89–285 °C. The smoke production at the time of 11 min to 15 min 50 s of fire was 1.76 m3/s, which was obtained through indirect calculation method.

  20. EVALUATING THE DIFFUSION OF FUEL-CELL CARS IN THE CHINA MARKETS

    OpenAIRE

    RITS, Vincent; KYPREOS, Socrates; WOKAUN, Alexander

    2004-01-01

    Air pollution is a major problem in many of China's cities, with SO2, NOx and PM emissions exceeding World Health Organisation's air quality standards. The environmental (dis-) performance of Chinese vehicles contributes largely to this problem. The fuel-cell system represents a technology that could eliminate much of the local air-pollution problem. However, the chances of fuel-cell cars during the next decades are still highly questioned. In this research, the diffusion of fuel-cell cars...

  1. Car Theft in Poland as a Part of the Risk in Auto Accident and Theft Insurance

    OpenAIRE

    Wieteska, Stanisław

    2015-01-01

    The problem of car theft has been observed for many years. The largest scale of this phenomenon occurred in the 1990’s. In this paper, the issue is discussed in social, ethical and economic aspects. We present the scale of the phenomenon of the theft of passenger vehicles in Poland in the years 2001–2012 in terms of the number of vehicles, type of stolen vehicles and the accident areas. In addition, we present the cause of theft and selected ways to protect cars from it. We als...

  2. Cars, Cars, Cars

    Science.gov (United States)

    McIntosh, Phyllis

    2013-01-01

    Cars are the focus of this feature article, which explores such topics as the history of cars in the United States, the national highway system, safety and pollution concerns, mobility and freedom for women, classic car shows, and the road trip in American literature and film. Also included are links to the websites of Automobile in American Life…

  3. Temperature rise and Heat build up inside a parked Car

    Science.gov (United States)

    Coady, Rose; Maheswaranathan, Ponn

    2001-11-01

    We have studied the heat build up inside a parked car under the hot summer Sun. Inside and outside temperatures were monitored every ten seconds from 9 AM to about 4 PM for a 2000 Toyota Camry parked in a Winthrop University parking lot without any shades or trees. Two PASCO temperature sensors, one inside the car and the other outside the car, are used along with PASCO-750 interface to collect the data. Data were collected under the following conditions while keeping track of the outside weather: fully closed windows, slightly open windows, half way open windows, fully open windows, and with window shades inside and outside. Inside temperatures reached as high as 150 degrees Fahrenheit on a sunny day with outside high temperature of about 100 degrees Fahrenheit. These results will be presented along with results from car cover and window tint manufacturers and suggestions to keep your car cool next time you park it under the Sun.

  4. Relieving the Impact of Transit Signal Priority on Passenger Cars through a Bilevel Model

    Directory of Open Access Journals (Sweden)

    Ding Wang

    2017-01-01

    Full Text Available Transit signal priority (TSP is an effective control strategy to improve transit operations on the urban network. However, the TSP may sacrifice the right-of-way of vehicles from side streets which have only few transit vehicles; therefore, how to minimize the negative impact of TSP strategy on the side streets is an important issue to be addressed. Concerning the typical mixed-traffic flow pattern and heavy transit volume in China, a bilevel model is proposed in this paper: the upper-level model focused on minimizing the vehicle delay in the nonpriority direction while ensuring acceptable delay variation in transit priority direction, and the lower-level model aimed at minimizing the average passenger delay in the entire intersection. The parameters which will affect the efficiency of the bilevel model have been analyzed based on a hypothetical intersection. Finally, a real-world intersection has been studied, and the average vehicle delay in the nonpriority direction decreased 11.28 s and 22.54 s (under different delay variation constraint compared to the models that only minimize average passenger delay, while the vehicle delay in the priority direction increased only 1.37 s and 2.87 s; the results proved the practical applicability and efficiency of the proposed bilevel model.

  5. The influence of various pressures in pneumatic tyre on braking process of car with anti-lock braking system

    Directory of Open Access Journals (Sweden)

    Damian HADRYŚ

    2008-01-01

    Full Text Available In this article has been presented the influence of various pressures inpneumatic tyre of passenger car Fiat Panda 1.3 JTD with anti-lock braking system on chosen parameters of braking process: course of braking deceleration, maximum value of deceleration, braking distances.

  6. Use of nonlinear asymmetrical shock absorber to improve comfort on passenger vehicles

    Science.gov (United States)

    Silveira, M.; Pontes, B. R.; Balthazar, J. M.

    2014-03-01

    In this study the behaviour of two different types of shock absorbers, symmetrical (linear) and asymmetrical (nonlinear) is compared for use on passenger vehicles. The analyses use different standard road inputs and include variation of the severity parameter, the asymmetry ratio and the velocity of the vehicle. Performance indices and acceleration values are used to assess the efficacy of the asymmetrical systems. The comparisons show that the asymmetrical system, with nonlinear characteristics, tends to have a smoother and more progressive performance, both for vertical and angular movements. The half-car front asymmetrical system was introduced, and the simulation results show that the use of the asymmetrical system only at the front of the vehicle can further diminish the angular oscillations. As lower levels of acceleration are essential for improved ride comfort, the use of asymmetrical systems for vibrations and impact absorption can be a more advantageous choice for passenger vehicles.

  7. Rail passengers rights

    Directory of Open Access Journals (Sweden)

    Đurđev Dušanka J.

    2016-01-01

    Full Text Available The legal framework of rail passengers rights is set out in a combination of international and European law: an international measure, the rather unwieldy Uniform Rules concerning the Contract for International Carriage of Passengers and Luggage by Rail, forming part of the Convention concerning International Carriage by Rail of 9 May 1980 (as amended by the Vilnius Protocol of 3 June 1999 ['CIV'], lays down a basic framework which is then fleshed out by more recent EU legislation, Regulation (EC No 1371/2007 on Rail Passengers ' Rights and Obligations. Regulation 1371/2007/EC on rail passenger rights and obligations sets out minimum quality standards that have to be guaranteed to all passengers on all lines. .

  8. Concentrations, properties, and health risk of PM2.5 in the Tianjin City subway system.

    Science.gov (United States)

    Wang, Bao-Qing; Liu, Jian-Feng; Ren, Zi-Hui; Chen, Rong-Hui

    2016-11-01

    A campaign was conducted to assess and compare the personal exposure in L3 of Tianjin subway, focusing on PM 2.5 levels, chemical compositions, morphology analysis, as well as the health risk of heavy metal in PM 2.5 . The results indicated that the average concentration of the PM 2.5 was 151.43 μg/m 3 inside the train of the subway during rush hours. PM 2.5 concentrations inside car under the ground are higher than those on the ground, and PM 2.5 concentrations on the platform are higher than those inside car. Regarding metal concentrations, the highest element in PM 2.5 samples was Fe; the level of which is 17.55 μg/m 3 . OC is a major component of PM 2.5 in Tianjin subway. Secondary organic carbon is the formation of gaseous organic pollutants in subway. SEM-EDX and TEM-EDX exhibit the presence of individual particle with a large metal content in the subway samples. For small Fe metal particles, iron oxide can be formed easily. With regard to their sources, Fe-containing particles are generated mainly from mechanical wear and friction processes at the rail-wheel-brake interfaces. The non-carcinogenic risk to metals Cr, Ni, Cu, Zn and Pb, and carcinogenic hazard of Cr and Ni were all below the acceptable level in L3 of Tianjin subway.

  9. Multi Car Elevator Control by using Learning Automaton

    Science.gov (United States)

    Shiraishi, Kazuaki; Hamagami, Tomoki; Hirata, Hironori

    We study an adaptive control technique for multi car elevators (MCEs) by adopting learning automatons (LAs.) The MCE is a high performance and a near-future elevator system with multi shafts and multi cars. A strong point of the system is that realizing a large carrying capacity in small shaft area. However, since the operation is too complicated, realizing an efficient MCE control is difficult for top-down approaches. For example, “bunching up together" is one of the typical phenomenon in a simple traffic environment like the MCE. Furthermore, an adapting to varying environment in configuration requirement is a serious issue in a real elevator service. In order to resolve these issues, having an autonomous behavior is required to the control system of each car in MCE system, so that the learning automaton, as the solutions for this requirement, is supposed to be appropriate for the simple traffic control. First, we assign a stochastic automaton (SA) to each car control system. Then, each SA varies its stochastic behavior distributions for adapting to environment in which its policy is evaluated with each passenger waiting times. That is LA which learns the environment autonomously. Using the LA based control technique, the MCE operation efficiency is evaluated through simulation experiments. Results show the technique enables reducing waiting times efficiently, and we confirm the system can adapt to the dynamic environment.

  10. Personal Exposure to PM2.5 in the Megacity of Mexico: A Multi-Mode Transport Study

    Directory of Open Access Journals (Sweden)

    Iván Y. Hernández-Paniagua

    2018-02-01

    Full Text Available Recurrent personal exposure to ambient PM2.5 is associated with adverse human health effects, in particular on the respiratory and cardiovascular systems. Here, we present an assessment of personal exposure and inhalation of PM2.5 for five modes of transport (walking, cycling, public bus (trolleybus and diesel bus, conventional car (CC and hybrid-electric car (HEC and two routes of similar distance, along a major road in the Mexico City metropolitan area (MCMA. Arithmetic average exposure concentrations ranged from 16.5 ± 6.5 µg m−3 for walking to 81.7 ± 9.1 µg m−3 for cycling (henceforth shown as average ±1 SD, with no significant differences with geometric averages. The maximum exposure concentration of 110.9 µg m−3 was observed for the conventional car. The highest exposure concentrations depended on route and the mode of transport, being observed for cycling and walking. The PM2.5 measurements showed large spatial heterogeneity in the exposure levels for walking and cycling, while public buses and private transport showed less spatial heterogeneity. The greatest peaks in PM2.5 coincided with 4-way intersections for all modes of transport, being positively influenced by traffic density. The mass of PM2.5 inhaled depended mostly on the mode of transport, and ranged between 1.0 ± 0.3 and 30.1 ± 14.2 µg km−1 for the HEC and bicycle, respectively. Local area PM2.5 increments identified as ‘residuals’ after subtraction of data recorded at the closest fixed monitoring site from exposure concentrations along the studied road suggested that inhalation for bicycle and diesel buses is strongly influenced by vehicular emissions. Residuals estimated for the trolleybus, CC and HEC confirmed a lower inhalation than for the other modes of transport evaluated due to protection by the cabin.

  11. The CERN car stickers for 2008 are now available

    CERN Multimedia

    2007-01-01

    All members of the personnel holding a valid contract (except owners of cars with green or CD plates) can come to the Registration Service (building 55, 1st floor) to obtain their 2008 car sticker, Mondays to Fridays from 7.30 a.m. to 4.00 p.m. non-stop. Please ensure you bring with you the following documents: the 2007 sticker for the vehicle in question, the "carte grise" registration paper of the vehicle in question (photocopies accepted). If you only wish to register one vehicle, you can obtain the 2008 sticker using the request form on the Web.NB: This notice only applies to members of the personnel who obtained one or several blue car stickers for 2007. Reception and Access Control Service – TS/FM

  12. NPS Transit System Passenger Boardings Study: Converting Ticket Sales to Passenger Boardings.

    Science.gov (United States)

    2016-01-01

    This report examines the reporting of passenger boardings (unlinked passenger trips) by NPS transit systems that use a ticket sales conversion methodology. By studying and validating the park units' passenger boarding methodology from converting tick...

  13. European type-approval test procedure for evaporative emissions from passenger cars against real-world mobility data from two Italian provinces.

    Science.gov (United States)

    Martini, Giorgio; Paffumi, Elena; De Gennaro, Michele; Mellios, Giorgos

    2014-07-15

    This paper presents an evaluation of the European type-approval test procedure for evaporative emissions from passenger cars based on real-world mobility data. The study relies on two large databases of driving patterns from conventional fuel vehicles collected by means of on-board GPS systems in the Italian provinces of Modena and Firenze. Approximately 28,000 vehicles were monitored, corresponding to approximately 36 million kilometres over a period of one month. The driving pattern of each vehicle was processed to derive the relation between trip length and parking duration, and the rate of occurrence of parking events against multiple evaporative cycles, defined on the basis of the type-approval test procedure as 12-hour diurnal time windows. These results are used as input for an emission simulation model, which calculates the total evaporative emissions given the characteristics of the evaporative emission control system of the vehicle and the ambient temperature conditions. The results suggest that the evaporative emission control system, fitted to the vehicles from Euro 3 step and optimised for the current type-approval test procedure, could not efficiently work under real-world conditions, resulting in evaporative emissions well above the type-approval limit, especially for small size vehicles and warm climate conditions. This calls for a revision of the type-approval test procedure in order to address real-world evaporative emissions. Copyright © 2014. Published by Elsevier B.V.

  14. Reconciling sectoral abatement strategies with global climate targets: the case of the Chinese passenger vehicle fleet.

    Science.gov (United States)

    Pauliuk, Stefan; Dhaniati, Ni Made A; Müller, Daniel B

    2012-01-03

    The IPCC Forth Assessment Report postulates that global warming can be limited to 2 °C by deploying technologies that are currently available or expected to be commercialized in the coming decades. However, neither specific technological pathways nor internationally binding reduction targets for different sectors or countries have been established yet. Using the passenger car stock in China as example we compute direct CO(2) emissions until 2050 depending on population, car utilization, and fuel efficiency and compare them to benchmarks derived by assuming even contribution of all sectors and a unitary global per capita emission quota. Compared to present car utilization in industrialized countries, massive deployment of prototypes of fuel efficient cars could reduce emissions by about 45%, and moderately lower car use could contribute with another 33%. Still, emissions remain about five times higher than the benchmark for the 2 °C global warming target. Therefore an extended analysis, including in particular low-carbon fuels and the impact of urban and transport planning on annual distance traveled and car ownership, should be considered. A cross-sectoral comparison could reveal whether other sectors could bear an overproportional reduction quota instead. The proposed model offers direct interfaces to material industries, fuel production, and scrap vehicle supply.

  15. Distracted driving behaviors of adults while children are in the car.

    Science.gov (United States)

    Roney, Linda; Violano, Pina; Klaus, Greg; Lofthouse, Rebecca; Dziura, James

    2013-10-01

    Cell phone use while driving is common and can result in driver distraction. However, data on the frequency of this behavior with other occupants in the vehicle are lacking. This study investigates whether adult drivers engage in cell phone use with passengers in the car and determines whether the frequency of these behaviors was modified if the passenger was a child. Subjects (N = 539) who have driven children during the previous 30 days were recruited to complete a survey regarding their cell phone usage while driving. The inclusion criteria of participants were as follows: 18 years or older with a valid driver's license, owns/uses a cell phone, drives with children, and reads English. Results were reported on a 4-point Likert scale (always, often, rarely, and never). Eighty percent of respondents reported cell phone use in some way while driving with children. As compared with similar behaviors when driving alone or with adult passengers, the odds of reporting "always" compared with "often, rarely, or never" of holding a cell phone in hand was 0.66 when driving with children. No significant differences were noted for the following variables: use of a blue tooth device or use of a cell phone to speak or text when parked. Cell phone use while driving is common. Distracted driving behaviors, although less frequent, persist when children are passengers in the vehicle. Further research into the effect of cell phone-related distracted driving behaviors of adults with child passengers is needed to address this public health concern.

  16. Car stickers for 2010

    CERN Multimedia

    GS Department

    The 2010 car stickers are now available. Holders of blue stickers will receive their 2010 stickers through the internal mail from 1st December onwards. Holders of red stickers are required to go to the Registration Service (Building 55, first floor), which is open non-stop from 7.30 a.m. to 4.00 p.m. Mondays to Fridays, in order to obtain their new stickers. They will be asked to present documents relating to the vehicles concerned. Owners of vehicles registered on green and CD plates should disregard this message. Reception and Access Control Service – GS/SEM/LS

  17. An IoT Based Predictive Connected Car Maintenance Approach

    Directory of Open Access Journals (Sweden)

    Rohit Dhall

    2017-03-01

    Full Text Available Internet of Things (IoT is fast emerging and becoming an almost basic necessity in general life. The concepts of using technology in our daily life is not new, but with the advancements in technology, the impact of technology in daily activities of a person can be seen in almost all the aspects of life. Today, all aspects of our daily life, be it health of a person, his location, movement, etc. can be monitored and analyzed using information captured from various connected devices. This paper discusses one such use case, which can be implemented by the automobile industry, using technological advancements in the areas of IoT and Analytics. ‘Connected Car’ is a terminology, often associated with cars and other passenger vehicles, which are capable of internet connectivity and sharing of various kinds of data with backend applications. The data being shared can be about the location and speed of the car, status of various parts/lubricants of the car, and if the car needs urgent service or not. Once data are transmitted to the backend services, various workflows can be created to take necessary actions, e.g. scheduling a service with the car service provider, or if large numbers of care are in the same location, then the traffic management system can take necessary action. ’Connected cars’ can also communicate with each other, and can send alerts to each other in certain scenarios like possible crash etc. This paper talks about how the concept of ‘connected cars’ can be used to perform ‘predictive car maintenance’. It also discusses how certain technology components, i.e., Eclipse Mosquito and Eclipse Paho can be used to implement a predictive connected car use case.

  18. THE INJURY SEVERITY RATE DIFFERENCES IN PASSENGER CARS AND PICK UP TRUCKS RELATED TWO VEHICLE INVOLVED MOTOR VEHICLE CRASHES IN BRITISH COLUMBIA, CANADA

    Directory of Open Access Journals (Sweden)

    E.B.R. DESAPRIYA

    2004-01-01

    Full Text Available The effect of large vehicle involvement on motor vehicle crash (MVC rates and severity has long been a concern in MVC analysis literature. Injuries in drivers and occupants are related to several key factors: the mass of the case vehicle and mass of its collision partner and speed of case vehicle and collision partner at the time of the crash. Objective: To evaluate the relative risk of injury occurrence in collisions between picks up trucks (PU and passenger sedan cars (PS. Methods: Data from the Insurance Corporation of British Columbia (ICBC crash data base was used to determine MVC rates and injury occurrence. Descriptive characteristics of the injury location and injury type were analyzed comparing the Odds Ratios and chi-squares. Results: PS occupants received more injuries; Odds Ratio was 2.49 (95% confidence interval: 2.15–2.88. Conclusion: Occupants in PS which collide with PU were at twice the risk of injuries. Concussion, whiplash, lacerations and abrasion were more frequent in PS drivers and occupants than in PU drivers and occupants. Overall, PS drivers/occupants experienced greater injuries than PU drivers/occupants in PU-PS collisions. In this paper, results are shown as odds ratios comparing occupants injuries in PS (case group with occupant injuries in PU (control group.

  19. Commuters’ Exposure to Particulate Matter Air Pollution Is Affected by Mode of Transport, Fuel Type, and Route

    Science.gov (United States)

    Zuurbier, Moniek; Hoek, Gerard; Oldenwening, Marieke; Lenters, Virissa; Meliefste, Kees; van den Hazel, Peter; Brunekreef, Bert

    2010-01-01

    Background Commuters are exposed to high concentrations of air pollutants, but little quantitative information is currently available on differences in exposure between different modes of transport, routes, and fuel types. Objectives The aim of our study was to assess differences in commuters’ exposure to traffic-related air pollution related to transport mode, route, and fuel type. Methods We measured particle number counts (PNCs) and concentrations of PM2.5 (particulate matter ≤ 2.5 μm in aerodynamic diameter), PM10, and soot between June 2007 and June 2008 on 47 weekdays, from 0800 to 1000 hours, in diesel and electric buses, gasoline- and diesel-fueled cars, and along two bicycle routes with different traffic intensities in Arnhem, the Netherlands. In addition, each-day measurements were taken at an urban background location. Results We found that median PNC exposures were highest in diesel buses (38,500 particles/cm3) and for cyclists along the high-traffic intensity route (46,600 particles/cm3) and lowest in electric buses (29,200 particles/cm3). Median PM10 exposure was highest from diesel buses (47 μg/m3) and lowest along the high- and low-traffic bicycle routes (39 and 37 μg/m3). The median soot exposure was highest in gasoline-fueled cars (9.0 × 10−5/m), diesel cars (7.9 × 10−5/m), and diesel buses (7.4 × 10−5/m) and lowest along the low-traffic bicycle route (4.9 × 10−5/m). Because the minute ventilation (volume of air per minute) of cyclists, which we estimated from measured heart rates, was twice the minute ventilation of car and bus passengers, we calculated that the inhaled air pollution doses were highest for cyclists. With the exception of PM10, we found that inhaled air pollution doses were lowest for electric bus passengers. Conclusions Commuters’ rush hour exposures were significantly influenced by mode of transport, route, and fuel type. PMID:20185385

  20. Price and income elasticities of demand for passenger transport fuels in Spain. Implications for public policies

    International Nuclear Information System (INIS)

    Romero-Jordan, Desiderio; Del Rio, Pablo; Jorge-Garcia, Marta; Burguillo, Mercedes

    2010-01-01

    The significant increase in passenger transport activity (cars) experienced by Spain and its associated increase in energy consumption have several associated negative aspects, including a greater dependence on foreign energy sources and higher GHG emissions. Therefore, reducing the level of transport activity would bring important socioeconomic and environmental benefits. The aim of this paper, which focuses on energy consumption in the passenger transport, is fourfold: (1) to provide a diagnostic of energy consumption in the Spanish passenger transport system and the related problems; (2) to develop a model to calculate price and income elasticities of demand for transport fuel; (3) to apply this model to the Spanish passenger transport sector; (4) to infer policy recommendations derived from the results of the diagnostic and the model. It is claimed that, in view of those low price elasticities and high income elasticities and if a reduction in the scale of transport activity is deemed socially desirable, a combination of instruments is necessary. Fuel taxes play an important role within this combination. Apart from their long-term effects, the low price elasticity of demand for transport fuel would allow the collection of a significant amount of revenues, which could eventually be earmarked to encourage reductions in private transport demand and modal shifts with other instruments. (author)

  1. Price and income elasticities of demand for passenger transport fuels in Spain. Implications for public policies

    Energy Technology Data Exchange (ETDEWEB)

    Romero-Jordan, Desiderio [Universidad Rey Juan Carlos, Madrid (Spain); Del Rio, Pablo [Institute for Public Goods and Policies (IPP), Consejo Superior de Investigaciones Cientificas (CSIC), C/Albasanz, 26-28, Madrid 28037 (Spain); Jorge-Garcia, Marta [Universidad de Leon (Spain); Burguillo, Mercedes [Universidad de Alcala (Spain)

    2010-08-15

    The significant increase in passenger transport activity (cars) experienced by Spain and its associated increase in energy consumption have several associated negative aspects, including a greater dependence on foreign energy sources and higher GHG emissions. Therefore, reducing the level of transport activity would bring important socioeconomic and environmental benefits. The aim of this paper, which focuses on energy consumption in the passenger transport, is fourfold: (1) to provide a diagnostic of energy consumption in the Spanish passenger transport system and the related problems; (2) to develop a model to calculate price and income elasticities of demand for transport fuel; (3) to apply this model to the Spanish passenger transport sector; (4) to infer policy recommendations derived from the results of the diagnostic and the model. It is claimed that, in view of those low price elasticities and high income elasticities and if a reduction in the scale of transport activity is deemed socially desirable, a combination of instruments is necessary. Fuel taxes play an important role within this combination. Apart from their long-term effects, the low price elasticity of demand for transport fuel would allow the collection of a significant amount of revenues, which could eventually be earmarked to encourage reductions in private transport demand and modal shifts with other instruments. (author)

  2. 'Diesel regenerativ' as fuel for passenger cars

    Energy Technology Data Exchange (ETDEWEB)

    Zimon, Anja; Krahl, Juergen [Coburg Univ. of Applied Sciences and Arts (Germany); Schroeder, Olaf; Fey, Barbara; Munack, Axel [Thuenen Institute, Braunschweig (Germany); Bockey, Dieter [Union for the Promotion of Oil and Protein Plants, Berlin

    2013-06-01

    Among the multitude of possible biofuels, hydrotreated vegetable oil (HVO) presents one possible means of partially replacing diesel fuel. In the project presented here, HVO was used with an admixture of biodiesel in the amount of 2% and 7% in two different vehicle fleets. HVO and biodiesel were made from domestic rapeseed oil. Both fuels trade under the name Diesel regenerative. The test vehicles were cars of the emission standards Euro 3 to Euro 6 that had been previously fueled with fossil diesel fuel, each for different periods. All vehicles were tested for regulated emissions at the beginning and the end of the project. In summary, emission reductions for hydrocarbons, carbon monoxide and particulate matter were identified for Diesel regenerative in comparison to fossil diesel fuel. However, nitrogen oxides were slightly increased for Diesel regenerative. Until now, this increase was only known in the literature to be associated with paraffinic fuel exhaust gases such as GTL. Moreover, decreases in nitrogen oxide when using pure HVO versus DF were published for utility vehicles (Warnecke et al., 2012). (orig.)

  3. Rage against the machine? Google's self-driving cars versus human drivers.

    Science.gov (United States)

    Teoh, Eric R; Kidd, David G

    2017-12-01

    Automated driving represents both challenges and opportunities in highway safety. Google has been developing self-driving cars and testing them under employee supervision on public roads since 2009. These vehicles have been involved in several crashes, and it is of interest how this testing program compares to human drivers in terms of safety. Google car crashes were coded by type and severity based on narratives released by Google. Crash rates per million vehicle miles traveled (VMT) were computed for crashes deemed severe enough to be reportable to police. These were compared with police-reported crash rates for human drivers. Crash types also were compared. Google cars had a much lower rate of police-reportable crashes per million VMT than human drivers in Mountain View, Calif., during 2009-2015 (2.19 vs 6.06), but the difference was not statistically significant. The most common type of collision involving Google cars was when they got rear-ended by another (human-driven) vehicle. Google cars shared responsibility for only one crash. These results suggest Google self-driving cars, while a test program, are safer than conventional human-driven passenger vehicles; however, currently there is insufficient information to fully examine the extent to which disengagements affected these results. Results suggest that highly-automated vehicles can perform more safely than human drivers in certain conditions, but will continue to be involved in crashes with conventionally-driven vehicles. Copyright © 2017. Published by Elsevier Ltd.

  4. Upscaling of a Batch De-Vulcanization Process for Ground Car Tire Rubber to a Continuous Process in a Twin Screw Extruder

    Directory of Open Access Journals (Sweden)

    Sitisaiyidah Saiwari

    2016-08-01

    Full Text Available As a means to decrease the amount of waste tires and to re-use tire rubber for new tires, devulcanization of ground passenger car tires is a promising process. Being an established process for NR and EPDM, earlier work has shown that for ground passenger car tire rubber with a relatively high amount of SBR, a devulcanization process can be formulated, as well. This was proven for a laboratory-scale batch process in an internal mixer, using diphenyl disulfide as the devulcanization aid and powder-sized material. In this paper, the devulcanization process for passenger car tire rubber is upscaled from 15 g per batch and transformed into a continuous process in a co-rotating twin screw extruder with a capacity of 2 kg/h. As SBR is rather sensitive to devulcanization process conditions, such as thermal and mechanical energy input, the screw design was based on a low shear concept. A granulate with particle sizes from 1–3.5 mm was chosen for purity, as well as economic reasons. The devulcanization process conditions were fine-tuned in terms of: devulcanization conditions (time/temperature profile, concentration of devulcanization aid, extruder parameters (screw configuration, screw speed, fill factor and ancillary equipment (pre-treatment, extrudate handling. The influence of these parameters on the devulcanization efficiency and the quality of the final product will be discussed. The ratio of random to crosslink scission as determined by a Horikx plot was taken for the evaluation of the process and material. A best practice for continuous devulcanization will be given.

  5. One-Quarter-Car Active SuspensionModel Verification

    Directory of Open Access Journals (Sweden)

    Hyniova Katerina

    2017-01-01

    Full Text Available Suspension system influences both the comfort and safety of the passengers. In the paper, energy recuperation and management in automotive suspension systems with linear electric motors that are controlled by a designed H∞ controller to generate a variable mechanical force for a car damper is presented. Vehicle shock absorbers in which forces are generated in response to feedback signals by active elements obviously offer increased design flexibility compared to the conventional suspensions with passive elements (springs and dampers. The main advantage of the proposed solution that uses a linear AC motor is the possibility to generate desired forces acting between the unsprung (wheel and sprung (one-quarter of the car body mass masses of the car, providing good insulation of the car sprung mass from the road surface roughness and load disturbances. As shown in the paper, under certain circumstances linear motors as actuators enable to transform mechanical energy of the vertical car vibrations to electrical energy, accumulate it, and use it when needed. Energy flow control enables to reduce or even eliminate the demands on the external power source. In particular, the paper is focused on experiments with active shock absorber that has been taken on the designed test bed and the way we developed an appropriate input signal for the test bed that as real road disturbance acts upon the vibration absorber and the obtained results are evaluated at the end. Another important point the active suspension design should satisfy is energy supply control that is made via standard controller modification, and which allows changing amount of energy required by the system. Functionality of the designed controller modification was verified taking various experiments on the experiment stand as mentioned in the paper.

  6. Effects of low concentration biodiesel blends application on modern passenger cars. Part 3: Impact on PAH, nitro-PAH, and oxy-PAH emissions

    International Nuclear Information System (INIS)

    Karavalakis, Georgios; Fontaras, Georgios; Ampatzoglou, Dimitrios; Kousoulidou, Marina; Stournas, Stamoulis; Samaras, Zissis; Bakeas, Evangelos

    2010-01-01

    This study explores the impact of five different types of methyl esters on polycyclic aromatic hydrocarbon (PAH), nitrated-PAH and oxygenated PAH emissions. The measurements were conducted on a chassis dynamometer, according to the European regulation. Each of the five different biodiesels was blended with EN590 diesel at a proportion of 10-90% v/v (10% biodiesel concentration). The vehicle was a Euro 3 compliant common-rail diesel passenger car. Emission measurements were performed over the NEDC and compared with those of the real traffic-based Artemis driving cycles. The experimental results showed that the addition of biodiesel led to some important increases in low molecular-weight PAHs (phenanthrene and anthracene) and to both increases and reductions in large PAHs which are characterised by their carcinogenic and mutagenic properties. Nitro-PAHs were found to reduce with biodiesel whereas oxy-PAH emissions presented important increases with the biodiesel blends. The impact of biodiesel source material was particularly clear on the formation of PAH compounds. It was found that most PAH emissions decreased as the average load and speed of the driving cycle increased. Cold-start conditions negatively influenced the formation of most PAH compounds. A similar trend was observed with particulate alkane emissions. - This investigation is a contribution to the understanding the impact of different biodiesels on the formation of PAHs, nitro-PAHs and oxy-PAHs over different driving conditions.

  7. Effects of fuel properties and oxidation catalyst on diesel exhaust emissions; Keiyu seijo oyobi sanka shokubai no diesel haishutsu gas eno eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Aihara, S; Morihisa, H; Tamanouchi, M; Araki, H; Yamada, S [Petroleum Energy Center, Advanced Technology and Research Institute, Tokyo (Japan)

    1997-10-01

    Effects of fuel properties (T90 and Poly-Aromatic Hydrocarbons: PAH) and oxidation catalyst on diesel exhaust emissions were studied using three DI diesel engines and two diesel passenger cars. (IDI engine) PM emissions were found to increase as T90 and PAH increased and could be decreased considerably for each fuel if an oxidation catalyst was installed. 5 refs., 9 figs., 3 tabs.

  8. An analysis on investments of transnational corporation in China’s car industry

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The transnational corporations began investing directly in China’s passenger car sector more than 2 decades ago, featuring characters unique in the world. This article, based on a case analysis, fully displays the characters of the transnational corporations in the process of entering the Chinese market, in regard to timing, partner choice, model distribution among different partners and the supplying system under the domination of their subsidiaries, and management of the networks and channels, and others.

  9. The influence of odd-even car trial on fine and coarse particles in Delhi.

    Science.gov (United States)

    Kumar, Prashant; Gulia, Sunil; Harrison, Roy M; Khare, Mukesh

    2017-06-01

    The odd-even car trial scheme, which reduced car traffic between 08.00 and 20.00 h daily, was applied from 1 to 15 January 2016 (winter scheme, WS) and 15-30 April 2016 (summer scheme, SS). The daily average PM 2.5 and PM 10 exceeded national standards, with highest concentrations (313 μg m -3 and 639 μg m -3 , respectively) during winter and lowest (53 μg m -3 and 130 μg m -3 ) during the monsoon (June-August). PM concentrations during the trials can be interpreted either as reduced or increased, depending on the periods used for comparison purposes. For example, hourly average net PM 2.5 and PM 10 (after subtracting the baseline concentrations) reduced by up to 74% during the majority (after 1100 h) of trial hours compared with the corresponding hours during the previous year. Conversely, daily average PM 2.5 and PM 10 were higher by up to 3-times during the trial periods when compared with the pre-trial days. A careful analysis of the data shows that the trials generated cleaner air for certain hours of the day but the persistence of overnight emissions from heavy goods vehicles into the morning odd-even hours (0800-1100 h) made them probably ineffective at this time. Any further trial will need to be planned very carefully if an effect due to traffic alone is to be differentiated from the larger effect caused by changes in meteorology and especially wind direction. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  10. 49 CFR 571.208 - Standard No. 208; Occupant crash protection.

    Science.gov (United States)

    2010-10-01

    ... September 1, 1996. S4.1.5.1Frontal/angular automatic protection system. (a) Each passenger car manufactured... active and passive restraint systems. S3. Application. (a) This standard applies to passenger cars... cars. S4.1.1Passenger cars manufactured from January 1, 1972, to August 31, 1973. Each passenger car...

  11. Anaheim electric vehicle car-sharing project

    Energy Technology Data Exchange (ETDEWEB)

    Kotler, D. [City of Anaheim Transportation Programs Planner, Anaheim, CA (United States); Chase, B. [Costa Mesa Planning Center, Costa Mesa, CA (United States)

    2000-07-01

    This paper described how the city of Anaheim in California is looking into a variety of clean transportation options for visitors, employees and residents in an effort to minimize air quality and congestion impacts. The city, which attracts approximately 24 million visitors annually, is looking into an electric vehicle (EV) car-sharing program that promotes EV use in multiple applications for both short- and long-term rental opportunities. There are two components to the program which provides eight 5-passenger electric Toyota RAV4 vehicles to both local employees and visitors. The electric RAV4s include nickel-hydride batteries which provide a range of 120 miles per charge. The city has already developed a network of public accessible EV charging stations and this project is a perfect extension of the city's continued efforts to seek opportunities to apply EV technologies within its jurisdictions. The Station Car Program provides flexibility for rail commuters to get from the rail station to their place of employment. On weekdays, the EVs are available to registered commuters at two rail stations to drive to and from work. A total of 32 commuters can benefit from the program at a cost of $40 per month. On weekends, the EVs are offered to visitors through Budget Rent-a-Car Agency at a rate comparable to gasoline-fueled vehicles. So far, participant feedback has been positive and the city is looking into expanding its efforts to provide clean transportation options. tab.

  12. The role of efficiency improvements vs. price effects for modeling passenger car transport demand and energy demand—Lessons from European countries

    International Nuclear Information System (INIS)

    Ajanovic, Amela; Haas, Reinhard

    2012-01-01

    The objective of this paper is to analyze the impact of changes in fuel prices and fuel intensity (i.e. liters of fuel used per 100 kilometers) on overall fuel (gasoline and diesel) consumption and on the demand for vehicle km driven in car passenger transport. This is important for deriving effective policy portfolios consisting of fuel taxes and technical standards such as fuel intensity mandates or specific CO 2 emission limits. To extract these impacts, we apply cointegration analyses to six European countries and their aggregate over the period 1970–2007. We consider the impact of fuel prices, household income and fuel intensity on fuel consumption. Furthermore, we investigate how changes in fuel prices and fuel intensity interact, analyzing the rebound effect due to lower fuel intensity and due to the switch to diesel. Because we find a high rebound effect with 44% more km driven if fuel intensity is improved 100%, the major conclusion of our analysis for policy makers is that technical standards as the only policy instrument will have limited success. Rather we recommend increased fuel taxes along with fuel intensity standards so that the taxes compensate for the rebound due to the standards. - Highlights: ► We find a high rebound effect with 44% more km driven if fuel intensity is improved. ► Technical standards as the only policy instrument will have limited success. ► Fuel taxes accompanied to fuel intensity standards may compensate the rebound effect.

  13. 49 CFR Subpart D - Appendix A-1 of FMVSS No. 208 Phase-in Reporting Requirements

    Science.gov (United States)

    2010-10-01

    ... manufacturers of passenger cars, and of trucks, buses and multipurpose passenger vehicles with a gross vehicle... passenger cars, and of trucks, buses and multipurpose passenger vehicles with a GVWR of 3,856 kg (8,500 lb... meaning. (b) Bus, gross vehicle weight rating or GVWR, multipurpose passenger vehicle, passenger car, and...

  14. Impact of passenger car NOX emissions on urban NO2 pollution - Scenario analysis for 8 European cities

    Science.gov (United States)

    Degraeuwe, Bart; Thunis, Philippe; Clappier, Alain; Weiss, Martin; Lefebvre, Wouter; Janssen, Stijn; Vranckx, Stijn

    2017-12-01

    Residents of large European cities are exposed to NO2 concentrations that often exceed the established air quality standards. Diesel cars have been identified as a major contributor to this situation; yet, it remains unclear to which levels the NOX emissions of diesel cars have to decrease to effectively mitigate urban NO2 pollution across Europe. Here, we take a continental perspective and model urban NO2 pollution in a generic street canyon of 8 major European cities for various NOX emission scenarios. We find that a reduction in the on-road NOX emissions of diesel cars to the Euro 6 level can in general decrease the regional and urban NO2 concentrations and thereby the frequency of exceedances of the NO2 air quality standard. High NO2 fractions in the NOX emissions of diesel cars tend to increase the urban NO2 concentrations only in proximity of intense road traffic typically found on artery roads in large cities like Paris and London. In cities with a low share of diesel cars in the vehicle fleet such as Athens or a high contribution from the NO2 background to the urban NO2 pollution such as Krakow, measures addressing heavy-duty vehicles, and the manufacturing, energy, and mining industry are necessary to decrease urban air pollution. We regard our model results as robust albeit subject to uncertainty resulting from the application of a generic street layout. With small modifications in the input parameters, our model could be used to assess the impact of NOX emissions from road transport on NO2 air pollution in any European city.

  15. Level of service for pedestrian movement towards the performance of passenger information in public transport stations in Klang Valley

    Science.gov (United States)

    Ramli, M. Z.; Hanipah, M. H.; Lee, L. G.; Loo, K. F.; Wong, J. K.; Zawawi, M. H.; Fuad, N. F. S.

    2017-09-01

    Rapid growth in car ownership in Malaysia plays a major role to traffic congestion. Hence, public transportation is crucial to cater the residents in high-density area especially in Klang Valley. Signage information in public transport station is one of an important passenger information system. Poor placement of sign information will decrease the efficiency of passenger flow and caused congestion in the station. Passenger information system is very useful for trip planning and decision making. Therefore, it is interesting to study the performance of passenger information system in focusing the movement behavior of pedestrian at non-peak period. Thus, the study on pedestrian movement during non-peak period on weekdays and weekends in mass transit stations and bus transit stations in Klang Valley was carried out by using video observation. The observation of the pedestrian movement was made in Mass Transit Station 1 in the middle of Kuala Lumpur and Mass Transit Station 2 in southern of Kuala Lumpur. The other site was focused at Bus Transit Station 1 in Putrajaya and Bus Transit Station 2 in Kajang. Findings shown that Mass Transit Station 1 having the best facility in terms of passenger information which the level of service obtained is LOS A, while the lowest level of service which is LOS E was obtained in Bus Transit Station 2.

  16. Modeling and Optimization of Collaborative Passenger Control in Urban Rail Stations under Mass Passenger Flow

    Directory of Open Access Journals (Sweden)

    Lili Wang

    2015-01-01

    Full Text Available With the rapid development of urban rail transit, the phenomenon of outburst passenger flows flocking to stations is occurring much more frequently. Passenger flow control is one of the main methods used to ensure passengers’ safety. While most previous studies have only focused on control measures inside the target station, ignoring the collaboration between stops, this paper puts emphasis on joint passenger control methods during the occurrence of large passenger flows. To provide a theoretic description for the problem under consideration, an integer programming model is built, based on the analysis of passenger delay and the processes by which passengers alight and board. Taking average passenger delay as the objective, the proposed model aims to disperse the pressure of oversaturated stations into others, achieving the optimal state for the entire line. The model is verified using a case study and the results show that restricted access measures taken collaboratively by stations produce less delay and faster evacuation. Finally, a sensitivity analysis is conducted, from which we find that the departure interval and maximum conveying capacity of the train affect passenger delay markedly in the process of passenger control and infer that control measures should be taken at stations near to the one experiencing an emergency.

  17. A systematic review of secondhand smoke exposure in a car: Attributable changes in atmospheric and biological markers.

    Science.gov (United States)

    Raoof, Sana A; Agaku, Israel T; Vardavas, Constantine I

    2015-05-01

    Exposure to secondhand smoke (SHS) has been linked to disease, disability, and premature death. While several countries have enacted smoke-free legislations, exposure to SHS may still occur in unregulated private environments, such as in the family car. We performed a systematic review of peer-reviewed literature in PubMed and Web of Science up to May 2013. Articles were selected if they provided a quantitative measure of SHS exposure (biological or atmospheric markers); the study was conducted inside a car; and the assessed exposure was attributable to cigarette combustion. From 202 articles identified, 12 met the inclusion criteria. Among all studies that assessed smoking in cars with at least one window partially open, the particulate matter 2.5 μm or less in diameter (PM2.5) concentrations ranged from 47 μg/m(3) to 12,150 μg/m(3). For studies with all windows closed, PM2.5 ranged from 203.6 μg/m(3) to 13,150 μg/m(3). SHS concentration in a car was mediated by air-conditioning status, extent of airflow, and driving speed. Smoking in cars leads to extremely high exposure to SHS and increased concentration of atmospheric markers of exposure-even in the presence of air-conditioning or increased airflow from open windows. This clearly shows that the only way to protect nonsmokers, especially children, from SHS within cars is by eliminating tobacco smoking. © The Author(s) 2015.

  18. Innovation for improvement of pedestrian protection as the challenge for the development of front-end structures of passenger cars; Innovationen zur Verbesserung des Fussgaengerschutzes als Herausforderung fuer die Entwicklung von PKW-Vorbaustrukturen

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, F.; Weidemann, W.; Jansohn, W.; Schneider, M. [EDAG Engineering and Design AG, Fulda (Germany)

    2001-07-01

    Requirements for improvement of pedestrian protection are the result of real-world accidents and test conditions, which take an important role in development of front-end structures of passenger cars at present, based on legal regulations (EU directives expected in 2005) and on car assessment programmes (application as per EuroNCAP since 1997). Styling and packaging are major considerations in conceptual realisation on a large scale. Furthermore, demands for minimisation of weight and cost have to be considered as marginal conditions. Solutions for this conflict of aims, which results from the new safety requirements and performance criteria for front-end structures, are to be represented and discussed based on concrete examples. (orig.) [German] Anforderungen zur Verbesserung des Fussgaengerschutzes resultieren einerseits aus dem Unfallgeschehen und andererseits aus Versuchsbedingungen, die derzeit auf der Basis von gesetzlichen Regelungen (erwartete EU-Richtlinie etwa im Jahr 2005) und von Sicherheitsbewertungen (Anwendung im Rahmen von EuroNCAP seit 1997) in der Vorbau-Entwicklung von Personenkraftwagen eine bedeutende Rolle einnehmen. Die konzeptionelle Umsetzung tangiert sowohl Styling als auch Packaging in erheblichem Umfang, darueber hinaus sind als Randbedingungen die Forderungen nach der Minimierung von Gewicht und Kosten zu beruecksichtigen. Die Loesungen dieses Zielkonfliktes, deren Wirkungsfeld durch die neuen Sicherheitsanforderungen und die Auslegungskriterien fuer Vorbaustrukturen aufgespannt wird, sollen anhand von konkreten Beispielen dargestellt und diskutiert werden. (orig.)

  19. Crash tests for passenger cars and their relationship to the actual accident occurrence

    International Nuclear Information System (INIS)

    Appel, Hermann; Lutter, Gerhard; Sigmund, Thomas

    1994-01-01

    Current consensus about crash tests implies that, for verification of self-protection of a vehicle or its occupants, at least three full size tests with the following specifications are necessary:(1)frontal impact against a rigid, non-moving 0 -barrier with 100% overlap;(2)frontal offset impact against a rigid, non-moving 15 -barrier with 50% overlap (impact speed between 50 and 55kmh -1 );(3)side impact of a moving deformable barrier; preferably according to EEVC-method (impact speed 50kmh -1 ).From the social general view it is not sufficient to test only the self-protection of the vehicle and to give most importance to the front of the vehicle. The other factors of passive safety, partner protection and compatibility, respectively, have to be included, as two thirds of the cost of injuries originates from car-to-car accidents, and only one third from vehicle collisions against fixed objects. It follows that at least one additional test of compatibility has to be added to those mentioned above. It has to be investigated whether this compatibility test could be a frontal impact against a controllably deformable barrier and could substitute one or even two of the first-mentioned tests. ((orig.))

  20. LHCb: Evidence of CP violation in charmless three-body decays $B^\\pm\\rightarrow K^\\pm\\pi^+\\pi^-$, $B^\\pm\\rightarrow K^\\pm K^+K^-$, $B^\\pm\\rightarrow K^+ K^-\\pi^\\pm$ and $B^\\pm\\rightarrow \\pi^\\pm\\pi^+\\pi^-$

    CERN Multimedia

    Lopes, J H

    2013-01-01

    Evidence of CP violation in charmless three-body decays $B^\\pm\\rightarrow K^\\pm\\pi^+\\pi^-$, $B^\\pm\\rightarrow K^\\pm K^+K^-$, $B^\\pm\\rightarrow K^+ K^-\\pi^\\pm$ and $B^\\pm\\rightarrow \\pi^\\pm\\pi^+\\pi^-$

  1. Analysis of impacts on urban air quality by restricting the operation of passenger vehicles during Asian Game events in Busan, Korea

    Science.gov (United States)

    Lee, Byeong-Kyu; Jun, Na-Young; Lee, Haengah Kim

    This study is an analysis of the impacts on urban air quality of restricting the operation of passenger vehicles during the 24th Asian Games (AG). Passenger vehicles in Busan were not allowed to operate on the alternative days during the AG period. This restricted operation of passenger vehicles was enforced to improve an urban air quality in Busan during the AG period. The average usage rate of passenger vehicles under an alternate (or restricted) operation was 95.4% and thus the average traffic flow rate (vehicle operation speed) increased approximately 28.1% as compared to normal periods. We analyzed the ambient concentrations of criteria air pollutants measured at 13 air-monitoring stations in Busan (Pusan), Korea, for the three periods of "before (13-28 September 2002)", "during (29 September-14 October 2002)" and "after (15-30 October 2002)" the AG. The 1-h, 24-h and 16-day averages or median concentrations of each classified term were compared to those of other terms. The median concentrations, based on 24-h average data of each day, of PM 10, CO, NO 2, and SO 2 in the ambient during the alternate operation period of 16 days substantially increased as compared to the terms before or after. However, the median concentration of O 3 during the AG period was slightly less than that of the term before. The ambient O 3 concentrations during daytime (12:00-19:00) under alternate operation substantially increased as compared to the terms before or after. However, the ambient O 3 concentrations during nighttime (22:00-07:00) under alternate operation decreased when compared to the terms before or after. For the alternate operation period of passenger vehicles, the average concentrations of PM 10, NO 2, SO 2, and daytime O 3 measured at the air-monitoring stations near the stadiums were much higher than those of the other areas excluding the stadium areas. However, average CO concentrations at the other areas were higher than those nearby the stadiums during the

  2. MMSE Estimator for Children’s Speech with Car and Weather Noise

    Science.gov (United States)

    Sayuthi, V.

    2018-04-01

    Previous research mentioned that most people need and use vehicles for various purposes, in this recent time and future, as a means of traveling. Many ways can be done in a vehicle, such as for enjoying entertainment, and doing work, so vehicles not just only as a means of traveling. In this study, we will examine the children’s speech from a girl in the vehicle that affected by noise disturbances from the sound source of car noise and the weather sound noise around it, in this case, the rainy weather noise. Vehicle sounds may be from car engine or car air conditioner. The minimum mean square error (MMSE) estimator is used as an attempt to obtain or detect the children’s clear speech by representing simulation research as random process signal that factored by the autocorrelation of both the child’s voice and the disturbance noise signal. This MMSE estimator can be considered as wiener filter as the clear sound are reconstructed again. We expected that the results of this study can help as the basis for development of entertainment or communication technology for passengers of vehicles in the future, particularly using MMSE estimators.

  3. Analysis of bus passenger comfort perception based on passenger load factor and in-vehicle time.

    Science.gov (United States)

    Shen, Xianghao; Feng, Shumin; Li, Zhenning; Hu, Baoyu

    2016-01-01

    Although bus comfort is a crucial indicator of service quality, existing studies tend to focus on passenger load and ignore in-vehicle time, which can also affect passengers' comfort perception. Therefore, by conducting surveys, this study examines passengers' comfort perception while accounting for both factors. Then, using the survey data, it performs a two-way analysis of variance and shows that both in-vehicle time and passenger load significantly affect passenger comfort. Then, a bus comfort model is proposed to evaluate comfort level, followed by a sensitivity analysis. The method introduced in this study has theoretical implications for bus operators attempting to improve bus service quality.

  4. Traffic generated non-exhaust particulate emissions from concrete pavement: A mass and particle size study for two-wheelers and small cars

    Science.gov (United States)

    Aatmeeyata; Kaul, D. S.; Sharma, Mukesh

    This study aimed to understand the non-exhaust (NE) emission of particles from wear of summer tire and concrete pavement, especially for two wheelers and small cars. A fully enclosed laboratory-scale model was fabricated to simulate road tire interaction with a facility to collect particles in different sizes. A road was cast using the M-45 concrete mixture and the centrifugal casting method. It was observed that emission of large particle non exhaust emission (LPNE) as well as PM 10 and PM 2.5 increased with increasing load. The LPNE was 3.5 mg tire -1 km -1 for a two wheeler and 6.4 mg tire -1 km -1 for a small car. The LPNE can lead to water pollution through water run-off from the roads. The contribution of the PM 10 and PM 2.5 was smaller compared to the LPNE particles (less than 0.1%). About 32 percent of particle mass of PM 10 was present below 1 μm. The number as well as mass size distribution for PM 10 was observed to be bi-modal with peaks at 0.3 μm and 4-5 μm. The NE emissions did not show any significant trend with change in tire pressure.

  5. Intermodal Passenger Connectivity Database -

    Data.gov (United States)

    Department of Transportation — The Intermodal Passenger Connectivity Database (IPCD) is a nationwide data table of passenger transportation terminals, with data on the availability of connections...

  6. 14 CFR 91.517 - Passenger information.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Passenger information. 91.517 Section 91... Multiengine Airplanes and Fractional Ownership Program Aircraft § 91.517 Passenger information. (a) Except as... belts and when smoking is prohibited. (c) If passenger information signs are installed, no passenger or...

  7. 75 FR 26839 - Metrics and Standards for Intercity Passenger Rail Service under Section 207 of the Passenger...

    Science.gov (United States)

    2010-05-12

    ... and Standards for Intercity Passenger Rail Service under Section 207 of the Passenger Rail Investment... performance and service quality of intercity passenger train operations. In compliance with the statute, the... Intercity Passenger Rail Service,'' on the FRA's Web site. Simultaneously, the FRA published a notice in the...

  8. Potential and impacts of car-sharing in the Helsinki metropolitan area, Tampere and Turku; Autojen yhteiskayton potentiaali ja vaikutukset paakaupunkiseudulla, Turussa ja Tampereella

    Energy Technology Data Exchange (ETDEWEB)

    Voltti, V.

    2010-07-01

    previously without a car will improve, but passenger car kilometres and emissions will increase. Those giving up their car or giving up purchasing one are in a minority in numerical terms, but their passenger car kilometres are significantly reduced. As a net impact of various changes, carbon dioxide emissions from transport will fall by approximately one-third as a result of car-sharing. Studies conducted in Finland, Europe and North America have reached more or less the same conclusion. There are approximately 100,000 potential car sharers in the Helsinki metropolitan area, Turku and Tampere. This potential amounts to some 5% of the population. A more narrowly determined key potential is approximately 40% of the full potential, i.e. about 40,000 car sharers. Based on a European comparison, reaching the key potential is realistic with a time span of 10-20 years. The study presents a forecast of the number of car sharing users based on the current trend as well as in the target situation for 2020 and 2030. The impacts of car-sharing in forecast situations are also presented in the study (orig.)

  9. Effect of consumer behaviour and perception on car purchase decision: Empirical Evidence from Lagos - Nigeria

    Directory of Open Access Journals (Sweden)

    Ph. D. Samuel Taiwo Akinyele

    2012-05-01

    Full Text Available In recent days Nigeria is witnessing a change in consumerism. The market is now predominantly consumer driven. The focus is shifting for product based marketing to need based marketing. Consumer is given many options to decide. Passenger car segment is no exception to this general trend. An effective market communication is imperative for reaching the target audience. So it is important that we study the consumer perceptions and behaviour of the car owners which will give us feedback on how marketing strategies can be worked. Victoria Island in Lagos State, which is in the Southern part of Nigeria, has a progressive and growing market for cars. This area was selected for this study.Pre-testing was done by an interview schedule which was developed and administered to a convenient sample of twenty five car owners. A simple random sampling technique was adopted in the study to select the sample respondents. As the size of the universe is restricted, the study has been conducted on the respondents who are the owners of all the segments of passenger cars. A total of 350 interview schedules were prepared and out of this, only 327 interview schedules were filled up and collected. Data were collected through an interview schedule regarding reception of the respondents on the usage of cars. The following tools were used in testing the hypotheses and in the analysis of data. Descriptive statistical tools such as percentage, mean, median and standard deviation have been used to describe the profiles of consumers, preferred product attributes and level of satisfaction. ANOVA, T- Test and F- test have been used to test the significant differences between the groups of respondents in their perception and satisfaction for selected independent variable like age, sex and income. Chi-square test has been used to test the association between the consumer demographic characteristics and preferred product attributes and satisfaction. Multiple regression analysis has

  10. Car crash fatalities associated with fire in Sweden.

    Science.gov (United States)

    Viklund, Åsa; Björnstig, Johanna; Larsson, Magnus; Björnstig, Ulf

    2013-01-01

    To study the epidemiology and causes of death in fatal car crashes on Swedish roads in which the victim's vehicle caught fire. The data set is from the Swedish Transport Administrations in-depth studies of fatal crashes 1998-2008. Autopsies from all cases provided data on injuries, toxicological analyses, and cause of death. In total, 181 people died in 133 burning cars, accounting for 5 percent of all deaths in passenger cars, sport utility vehicles, vans, and minibuses during 1998 to 2008. The cause of death for a third of the victims was fire related, as burns and/or smoke inhalation injuries, with no fatal trauma injuries. Twenty-five of these 55 deaths were persons 19 years or younger and included 15 of 18 rear seat deaths. Over half of the 181 deaths were in vehicles that had collided with another vehicle and, of these cases, half were killed in collisions with heavy vehicles. The percentage of drivers with illegal blood alcohol concentrations (27%) and suicides (5.5%) were not higher than in other fatal crashes on Swedish roads. The ignition point of the fire was indicated in only half of the cases and, of those, half started in the engine compartment and one fourth started around the fuel tank or lines. Car fires are a deadly postcrash problem. Reducing this risk would be primarily a responsibility for the automotive industry. A multifactor approach could be considered as follows: risk-reducing design, insulation, reduced flammability in motor compartment fluids and plastics, and automatic fire extinguishing equipment. Inspiration could be found in how, for example, the auto racing and aviation industries handle this problem.

  11. Exploring Concepts of Operations for On-Demand Passenger Air Transportation

    Science.gov (United States)

    Nneji, Victoria Chibuogu; Stimpson, Alexander; Cummings, Mary; Goodrich, Kenneth H.

    2017-01-01

    In recent years, a surge of interest in "flying cars" for city commutes has led to rapid development of new technologies to help make them and similar on-demand mobility platforms a reality. To this end, this paper provides analyses of the stakeholders involved, their proposed operational concepts, and the hazards and regulations that must be addressed. Three system architectures emerged from the analyses, ranging from conventional air taxi to revolutionary fully autonomous aircraft operations, each with vehicle safety functions allocated differently between humans and machines. Advancements for enabling technologies such as distributed electric propulsion and artificial intelligence have had major investments and initial experimental success, but may be some years away from being deployed for on-demand passenger air transportation at scale.

  12. Service Capacity Reserve under Uncertainty by Hospital’s ER Analogies: A Practical Model for Car Services

    Directory of Open Access Journals (Sweden)

    Miguel Ángel Pérez Salaverría

    2014-01-01

    Full Text Available We define a capacity reserve model to dimension passenger car service installations according to the demographic distribution of the area to be serviced by using hospital’s emergency room analogies. Usually, service facilities are designed applying empirical methods, but customers arrive under uncertain conditions not included in the original estimations, and there is a gap between customer’s real demand and the service’s capacity. Our research establishes a valid methodology and covers the absence of recent researches and the lack of statistical techniques implementation, integrating demand uncertainty in a unique model built in stages by implementing ARIMA forecasting, queuing theory, and Monte Carlo simulation to optimize the service capacity and occupancy, minimizing the implicit cost of the capacity that must be reserved to service unexpected customers. Our model has proved to be a useful tool for optimal decision making under uncertainty integrating the prediction of the cost implicit in the reserve capacity to serve unexpected demand and defining a set of new process indicators, such us capacity, occupancy, and cost of capacity reserve never studied before. The new indicators are intended to optimize the service operation. This set of new indicators could be implemented in the information systems used in the passenger car services.

  13. 19 CFR 4.50 - Passenger lists.

    Science.gov (United States)

    2010-04-01

    ... VESSELS IN FOREIGN AND DOMESTIC TRADES Passengers on Vessels § 4.50 Passenger lists. (a) The master of... passenger and crew lists, as required by § 4.7(a) of this part. If the vessel is arriving from noncontiguous... 19 Customs Duties 1 2010-04-01 2010-04-01 false Passenger lists. 4.50 Section 4.50 Customs Duties...

  14. Analysis of aging mechanism and management for HTR-PM reactor pressure vessel

    International Nuclear Information System (INIS)

    Sun Yunxue; Shao Jin

    2015-01-01

    Reactor pressure vessel is an important part of the reactor pressure boundary, its important degree ranks high in ageing management and life assessment of nuclear power plant. Carrying out systematic aging management to ensure reactor pressure vessel keeping enough safety margins and executing design functions is one of the key factors to guarantee security and stability operation for nuclear power plant during the whole lifetime and prolong life. This paper briefly introduces the structure and aging mechanism of reactor pressure vessel in pressurized water reactor nuclear power plant, and introduces the design principle and structure characteristics of HTR-PM. At the same time, this paper carries out preliminary analysis and exploration. and discusses aging management of HTR-PM reactor pressure vessel. Finally, the advice of carring out aging management for HTR-PM reactor pressure vessel is proposed. (authors)

  15. The prospect for modal shifts in passenger transport worldwide and impacts on energy use and CO2

    International Nuclear Information System (INIS)

    Cuenot, Francois; Fulton, Lew; Staub, John

    2012-01-01

    Travel statistics for most countries are subject to numerous uncertainties. But as presented in this paper, the IEA has developed a sufficient database to estimate passenger travel by mode for major countries and regions around the world, and produce consistent travel and energy use estimates, perhaps the first of their kind. For example, we estimate that in 2005 total global passenger travel using motorised modes was about 40 trillion kilometres, or about 6000 per person. The IEA has also developed a set of travel projections to 2050, including a Baseline and a “Modal Shift” scenario. This paper provides the result of this analysis and estimates the potential impacts on CO 2 from a 25% reduction in car and air travel by 2050 relative to the Baseline in that year. The modelling effort and policy analysis used to support the findings are also described.

  16. Experimental and numerical investigation of idling car exposure

    Energy Technology Data Exchange (ETDEWEB)

    McNabola, A; Broderick, B M; Gill, L W [Trinity College, Dublin (Ireland). Dept. of Civil, Structural, and Environmental Engineering

    2006-07-01

    This study examined the effect of maintaining a 2 metre distance between vehicles on commuter pollution exposure levels. Air quality samples were recorded inside cars on a busy road in Dublin. A turbulent dispersion model was used to predict the exposure levels from idling cars. Samples were recorded along the route by keeping a distance of approximately 2 metres by sight to the car in front, and then a second time keeping a distance of approximately 1 meter. Traffic numbers were recorded during each sample from local authority loops. Meteorological and idling time data were also recorded for a total of 10 pairs of samples. Experiments were then conducted to measure volatile organic compounds (VOCs) and particulate matter (PM{sub 2.5}). A calibrated computational fluid dynamics (CFD) model was then used to predict car exposure levels under varying conditions. Key parameters included ventilation rates; wind speed; and distance. The calibrated numerical model demonstrated that the pollution concentration decreased rapidly within the first 2 metres of the preceding exhaust. Maintaining a distance of 2 metres to the preceding vehicle showed a reduction in VOCs and particulate matter of approximately 30 to 40 per cent. It was concluded that further research is needed to determine if modified driving behaviours will promote higher levels of traffic congestion. 11 refs., 6 tabs., 11 figs.

  17. Passengers, Information, and Disruptions

    NARCIS (Netherlands)

    E. van der Hurk (Evelien)

    2015-01-01

    markdownabstract__Abstract__ Passengers traveling in public transport generate a detailed digital track record of their journey through using automated fare collection systems and carrying mobile devices. This information on passenger behavior has only recently become available to public

  18. Experimental Study of Interior Temperature Distribution Inside Parked Automobile Cabin

    Directory of Open Access Journals (Sweden)

    Issam Mohammed Ali Aljubury

    2015-03-01

    Full Text Available Temperature inside the vehicle cabin is very important to provide comfortable conditions to the car passengers. Temperature inside the cabin will be increased, when the car is left or parked directly under the sunlight. Experimental studies were performed in Baghdad, Iraq (33.3 oN, 44.4 oE to investigate the effects of solar radiation on car cabin components (dashboard, steering wheel, seat, and inside air. The test vehicle was oriented to face south to ensure maximum (thermal sun load on the front windscreen. Six different parking conditions were investigated. A suggested car cover was examined experimentally. The measurements were recorded for clear sky summer days started at 8 A.M. till 5 P.M. Results show that interior air temperature in unshaded parked car reaches 70oC and dashboard temperature can approach 100 oC. While, cardboard car shade inside the car not reduce the air temperature inside it. Suggested car cover with 1 cm part-down side windows reduced temperature of cabin components by 70 % in average compare to the base case.

  19. Evolution of the crashworthiness and aggressivity of the Spanish car fleet.

    Science.gov (United States)

    Gómez Méndez, Alvaro; Aparicio Izquierdo, Francisco; Arenas Ramírez, Blanca

    2010-11-01

    This paper investigates the relationship between a passenger car's year of registration and its crashworthiness and aggressivity in real-world crashes. Crashworthiness is defined as the ability of a car to protect its own occupants, and has been evaluated in single and two-car crashes. Aggressivity is defined as the ability to protect users travelling in other vehicles, and has been evaluated only in two-car crashes. The dependent variable is defined as the proportion of injured drivers who are killed or seriously injured; following previous research, we refer to this magnitude as injury severity. A decrease in the injury severity of a driver is interpreted as an improvement in the crashworthiness of their car; similarly, a decrease in the injury severity of the opponent driver is regarded as an improvement in aggressivity. Data have been extracted from the Spanish Road Accident Database, which contains information on every accident registered by the police in which at least one person was injured. Two types of regression models have been used: logistic regression models in single-car crashes, and generalised estimating equations (GEE) models in two-car crashes. GEE allow to take account of the correlation between the injury severities of drivers involved in the same crash. The independent variables considered have been: year of registration of the subject car (crashworthiness component), year of registration of the opponent car (aggressivity component), and several factors related to road, driver and environment. Our models confirm that crashworthiness has largely improved in two-car crashes: when crashing into the average opponent car, drivers of cars registered before 1985 have a significantly higher probability of being killed or seriously injured than drivers of cars registered in 2000-2005 (odds ratio: 1.80; 95% confidence interval: 1.61; 2.01). In single-car crashes, the improvement in crashworthiness is very slight (odds ratio: 1.04; 95% confidence interval

  20. Observation of the suppressed ADS modes $B^\\pm \\to [\\pi^\\pm K^\\mp \\pi^+\\pi^-]_D K^\\pm$ and $B^\\pm \\to [\\pi^\\pm K^\\mp \\pi^+\\pi^-]_D \\pi^\\pm$

    CERN Document Server

    INSPIRE-00258707; Abellan Beteta, C; Adeva, B; Adinolfi, M; Adrover, C; Affolder, A; Ajaltouni, Z; Albrecht, J; Alessio, F; Alexander, M; Ali, S; Alkhazov, G; Alvarez Cartelle, P; Alves Jr, A A; Amato, S; Amerio, S; Amhis, Y; Anderlini, L; Anderson, J; Andreassen, R; Appleby, R B; Aquines Gutierrez, O; Archilli, F; Artamonov, A; Artuso, M; Aslanides, E; Auriemma, G; Bachmann, S; Back, J J; Baesso, C; Balagura, V; Baldini, W; Barlow, R J; Barschel, C; Barsuk, S; Barter, W; Bauer, Th; Bay, A; Beddow, J; Bedeschi, F; Bediaga, I; Belogurov, S; Belous, K; Belyaev, I; Ben-Haim, E; Benayoun, M; Bencivenni, G; Benson, S; Benton, J; Berezhnoy, A; Bernet, R; Bettler, M -O; van Beuzekom, M; Bien, A; Bifani, S; Bird, T; Bizzeti, A; Bjørnstad, P M; Blake, T; Blanc, F; Blouw, J; Blusk, S; Bocci, V; Bondar, A; Bondar, N; Bonivento, W; Borghi, S; Borgia, A; Bowcock, T J V; Bowen, E; Bozzi, C; Brambach, T; van den Brand, J; Bressieux, J; Brett, D; Britsch, M; Britton, T; Brook, N H; Brown, H; Burducea, I; Bursche, A; Busetto, G; Buytaert, J; Cadeddu, S; Callot, O; Calvi, M; Calvo Gomez, M; Camboni, A; Campana, P; Carbone, A; Carboni, G; Cardinale, R; Cardini, A; Carranza-Mejia, H; Carson, L; Carvalho Akiba, K; Casse, G; Cattaneo, M; Cauet, Ch; Charles, M; Charpentier, Ph; Chen, P; Chiapolini, N; Chrzaszcz, M; Ciba, K; Cid Vidal, X; Ciezarek, G; Clarke, P E L; Clemencic, M; Cliff, H V; Closier, J; Coca, C; Coco, V; Cogan, J; Cogneras, E; Collins, P; Comerma-Montells, A; Contu, A; Cook, A; Coombes, M; Coquereau, S; Corti, G; Couturier, B; Cowan, G A; Craik, D; Cunliffe, S; Currie, R; D'Ambrosio, C; David, P; David, P N Y; De Bonis, I; De Bruyn, K; De Capua, S; De Cian, M; De Miranda, J M; De Oyanguren Campos, M; De Paula, L; De Silva, W; De Simone, P; Decamp, D; Deckenhoff, M; Del Buono, L; Derkach, D; Deschamps, O; Dettori, F; Di Canto, A; Dijkstra, H; Dogaru, M; Donleavy, S; Dordei, F; Dosil Suárez, A; Dossett, D; Dovbnya, A; Dupertuis, F; Dzhelyadin, R; Dziurda, A; Dzyuba, A; Easo, S; Egede, U; Egorychev, V; Eidelman, S; van Eijk, D; Eisenhardt, S; Eitschberger, U; Ekelhof, R; Eklund, L; El Rifai, I; Elsasser, Ch; Elsby, D; Falabella, A; Färber, C; Fardell, G; Farinelli, C; Farry, S; Fave, V; Ferguson, D; Fernandez Albor, V; Ferreira Rodrigues, F; Ferro-Luzzi, M; Filippov, S; Fitzpatrick, C; Fontana, M; Fontanelli, F; Forty, R; Francisco, O; Frank, M; Frei, C; Frosini, M; Furcas, S; Furfaro, E; Gallas Torreira, A; Galli, D; Gandelman, M; Gandini, P; Gao, Y; Garofoli, J; Garosi, P; Garra Tico, J; Garrido, L; Gaspar, C; Gauld, R; Gersabeck, E; Gersabeck, M; Gershon, T; Ghez, Ph; Gibson, V; Gligorov, V V; Göbel, C; Golubkov, D; Golutvin, A; Gomes, A; Gordon, H; Grabalosa Gándara, M; Graciani Diaz, R; Granado Cardoso, L A; Graugés, E; Graziani, G; Grecu, A; Greening, E; Gregson, S; Grünberg, O; Gui, B; Gushchin, E; Guz, Yu; Gys, T; Hadjivasiliou, C; Haefeli, G; Haen, C; Haines, S C; Hall, S; Hampson, T; Hansmann-Menzemer, S; Harnew, N; Harnew, S T; Harrison, J; Hartmann, T; He, J; Heijne, V; Hennessy, K; Henrard, P; Hernando Morata, J A; van Herwijnen, E; Hicks, E; Hill, D; Hoballah, M; Hombach, C; Hopchev, P; Hulsbergen, W; Hunt, P; Huse, T; Hussain, N; Hutchcroft, D; Hynds, D; Iakovenko, V; Idzik, M; Ilten, P; Jacobsson, R; Jaeger, A; Jans, E; Jaton, P; Jing, F; John, M; Johnson, D; Jones, C R; Jost, B; Kaballo, M; Kandybei, S; Karacson, M; Karbach, T M; Kenyon, I R; Kerzel, U; Ketel, T; Keune, A; Khanji, B; Kochebina, O; Komarov, I; Koopman, R F; Koppenburg, P; Korolev, M; Kozlinskiy, A; Kravchuk, L; Kreplin, K; Kreps, M; Krocker, G; Krokovny, P; Kruse, F; Kucharczyk, M; Kudryavtsev, V; Kvaratskheliya, T; La Thi, V N; Lacarrere, D; Lafferty, G; Lai, A; Lambert, D; Lambert, R W; Lanciotti, E; Lanfranchi, G; Langenbruch, C; Latham, T; Lazzeroni, C; Le Gac, R; van Leerdam, J; Lees, J -P; Lefèvre, R; Leflat, A; Lefrançois, J; Leo, S; Leroy, O; Leverington, B; Li, Y; Li Gioi, L; Liles, M; Lindner, R; Linn, C; Liu, B; Liu, G; von Loeben, J; Lohn, S; Lopes, J H; Lopez Asamar, E; Lopez-March, N; Lu, H; Lucchesi, D; Luisier, J; Luo, H; Machefert, F; Machikhiliyan, I V; Maciuc, F; Maev, O; Malde, S; Manca, G; Mancinelli, G; Marconi, U; Märki, R; Marks, J; Martellotti, G; Martens, A; Martin, L; Martín Sánchez, A; Martinelli, M; Martinez Santos, D; Martins Tostes, D; Massafferri, A; Matev, R; Mathe, Z; Matteuzzi, C; Maurice, E; Mazurov, A; McCarthy, J; McNulty, R; Mcnab, A; Meadows, B; Meier, F; Meissner, M; Merk, M; Milanes, D A; Minard, M -N; Molina Rodriguez, J; Monteil, S; Moran, D; Morawski, P; Morello, M J; Mountain, R; Mous, I; Muheim, F; Müller, K; Muresan, R; Muryn, B; Muster, B; Naik, P; Nakada, T; Nandakumar, R; Nasteva, I; Needham, M; Neufeld, N; Nguyen, A D; Nguyen, T D; Nguyen-Mau, C; Nicol, M; Niess, V; Niet, R; Nikitin, N; Nikodem, T; Nomerotski, A; Novoselov, A; Oblakowska-Mucha, A; Obraztsov, V; Oggero, S; Ogilvy, S; Okhrimenko, O; Oldeman, R; Orlandea, M; Otalora Goicochea, J M; Owen, P; Pal, B K; Palano, A; Palutan, M; Panman, J; Papanestis, A; Pappagallo, M; Parkes, C; Parkinson, C J; Passaleva, G; Patel, G D; Patel, M; Patrick, G N; Patrignani, C; Pavel-Nicorescu, C; Pazos Alvarez, A; Pellegrino, A; Penso, G; Pepe Altarelli, M; Perazzini, S; Perego, D L; Perez Trigo, E; Pérez-Calero Yzquierdo, A; Perret, P; Perrin-Terrin, M; Pessina, G; Petridis, K; Petrolini, A; Phan, A; Picatoste Olloqui, E; Pietrzyk, B; Pilař, T; Pinci, D; Playfer, S; Plo Casasus, M; Polci, F; Polok, G; Poluektov, A; Polycarpo, E; Popov, D; Popovici, B; Potterat, C; Powell, A; Prisciandaro, J; Pugatch, V; Puig Navarro, A; Punzi, G; Qian, W; Rademacker, J H; Rakotomiaramanana, B; Rangel, M S; Raniuk, I; Rauschmayr, N; Raven, G; Redford, S; Reid, M M; dos Reis, A C; Ricciardi, S; Richards, A; Rinnert, K; Rives Molina, V; Roa Romero, D A; Robbe, P; Rodrigues, E; Rodriguez Perez, P; Roiser, S; Romanovsky, V; Romero Vidal, A; Rouvinet, J; Ruf, T; Ruffini, F; Ruiz, H; Ruiz Valls, P; Sabatino, G; Saborido Silva, J J; Sagidova, N; Sail, P; Saitta, B; Salzmann, C; Sanmartin Sedes, B; Sannino, M; Santacesaria, R; Santamarina Rios, C; Santovetti, E; Sapunov, M; Sarti, A; Satriano, C; Satta, A; Savrie, M; Savrina, D; Schaack, P; Schiller, M; Schindler, H; Schlupp, M; Schmelling, M; Schmidt, B; Schneider, O; Schopper, A; Schune, M -H; Schwemmer, R; Sciascia, B; Sciubba, A; Seco, M; Semennikov, A; Senderowska, K; Sepp, I; Serra, N; Serrano, J; Seyfert, P; Shapkin, M; Shapoval, I; Shatalov, P; Shcheglov, Y; Shears, T; Shekhtman, L; Shevchenko, O; Shevchenko, V; Shires, A; Silva Coutinho, R; Skwarnicki, T; Smith, N A; Smith, E; Smith, M; Sokoloff, M D; Soler, F J P; Soomro, F; Souza, D; Souza De Paula, B; Spaan, B; Sparkes, A; Spradlin, P; Stagni, F; Stahl, S; Steinkamp, O; Stoica, S; Stone, S; Storaci, B; Straticiuc, M; Straumann, U; Subbiah, V K; Swientek, S; Syropoulos, V; Szczekowski, M; Szczypka, P; Szumlak, T; T'Jampens, S; Teklishyn, M; Teodorescu, E; Teubert, F; Thomas, C; Thomas, E; van Tilburg, J; Tisserand, V; Tobin, M; Tolk, S; Tonelli, D; Topp-Joergensen, S; Torr, N; Tournefier, E; Tourneur, S; Tran, M T; Tresch, M; Tsaregorodtsev, A; Tsopelas, P; Tuning, N; Ubeda Garcia, M; Ukleja, A; Urner, D; Uwer, U; Vagnoni, V; Valenti, G; Vazquez Gomez, R; Vazquez Regueiro, P; Vecchi, S; Velthuis, J J; Veltri, M; Veneziano, G; Vesterinen, M; Viaud, B; Vieira, D; Vilasis-Cardona, X; Vollhardt, A; Volyanskyy, D; Voong, D; Vorobyev, A; Vorobyev, V; Voß, C; Voss, H; Waldi, R; Wallace, R; Wandernoth, S; Wang, J; Ward, D R; Watson, N K; Webber, A D; Websdale, D; Whitehead, M; Wicht, J; Wiechczynski, J; Wiedner, D; Wiggers, L; Wilkinson, G; Williams, M P; Williams, M; Wilson, F F; Wishahi, J; Witek, M; Wotton, S A; Wright, S; Wu, S; Wyllie, K; Xie, Y; Xing, F; Xing, Z; Yang, Z; Young, R; Yuan, X; Yushchenko, O; Zangoli, M; Zavertyaev, M; Zhang, F; Zhang, L; Zhang, W C; Zhang, Y; Zhelezov, A; Zhokhov, A; Zhong, L; Zvyagin, A

    2013-01-01

    An analysis of $B^{\\pm}\\to DK^{\\pm}$ and $B^{\\pm}\\to D\\pi^{\\pm}$ decays is presented where the $D$ meson is reconstructed in the four-body final state $K^{\\pm}\\pi^{\\mp} \\pi^+ \\pi^-$. Using LHCb data corresponding to an integrated luminosity of $1.0{\\rm \\,fb}^{-1}$, first observations are made of the suppressed ADS modes $B^{\\pm}\\to [\\pi^{\\pm} K^{\\mp}\\pi^+\\pi^-]_D K^{\\pm}$ and $B^{\\pm}\\to [\\pi^{\\pm} K^{\\mp} \\pi^+\\pi^- ]_D\\pi^{\\pm}$ with a significance of $5.1\\sigma$ and greater than $10\\sigma$, respectively. Measurements of $CP$ asymmetries and $CP$-conserving ratios of partial widths from this family of decays are also performed. The magnitude of the ratio between the suppressed and favoured $B^{\\pm}\\to DK^{\\pm}$ amplitudes is determined to be $r^K_B = 0.097 \\pm{0.011}$.

  1. Black carbon and particulate matter (PM2.5) concentrations in New York City's subway stations.

    Science.gov (United States)

    Vilcassim, M J Ruzmyn; Thurston, George D; Peltier, Richard E; Gordon, Terry

    2014-12-16

    The New York City (NYC) subway is the main mode of transport for over 5 million passengers on an average weekday. Therefore, airborne pollutants in the subway stations could have a significant impact on commuters and subway workers. This study looked at black carbon (BC) and particulate matter (PM2.5) concentrations in selected subway stations in Manhattan. BC and PM2.5 levels were measured in real time using a Micro-Aethalometer and a PDR-1500 DataRAM, respectively. Simultaneous samples were also collected on quartz filters for organic and elemental carbon (OC/EC) analysis and on Teflon filters for gravimetric and trace element analysis. In the underground subway stations, mean real time BC concentrations ranged from 5 to 23 μg/m(3), with 1 min average peaks >100 μg/m(3), while real time PM2.5 levels ranged from 35 to 200 μg/m(3). Mean EC levels ranged from 9 to 12.5 μg/m(3). At street level on the same days, the mean BC and PM2.5 concentrations were below 3 and 10 μg/m(3), respectively. This study shows that both BC soot and PM levels in NYC's subways are considerably higher than ambient urban street levels and that further monitoring and investigation of BC and PM subway exposures are warranted.

  2. The influence of parental education and other socio-economic factors on child car seat use.

    Science.gov (United States)

    Rok Simon, Mateja; Korošec, Aleš; Bilban, Marjan

    2017-03-01

    The behaviour of parents in ensuring car passenger safety for their children is associated with socio-economic (SE) status of the family; however, the influence of parental education has rarely been researched and the findings are contradictory. The aim of the study was to clarify whether parental education influences the use of a child car seat during short rides. A cross-sectional survey was carried out in outpatient clinics for children's healthcare across Slovenia. 904 parents of 3-year-old children participated in the study; the response rate was 95.9%. A self-administered questionnaire was used. A binary multiple logistic regression was applied to assess the association between parental unsafe behaviour as dependent variable, and education and other SE factors as independent variables. 14.6% of parents did not use a child car seat during short rides. Families where mother had low or college education had higher odds of the non-use of a child car seat than families where mother had a university education. Single-parent families and those who lived in areas with low or medium SE status also had higher odds of the non-use of a child car seat. Low educational attainment influences parents' behaviour regarding the non-use of a child car seat. Low parental education is not the only risk factor since some highly educated parents also have high odds of unsafe behaviour. All parents should therefore be included in individually tailored safety counselling programmes. SE inequalities could be further reduced with provision of free child car seats for eligible families.

  3. Ticketing aggressive cars and trucks (TACT): How does it work on city streets?

    Science.gov (United States)

    Telford, Russell; Cook, Lawrence J; Olson, Lenora M

    2018-02-17

    The purpose of this study was to determine the feasibility of modifying the Ticking Aggressive Cars and Trucks (TACT) program, originally designed to work on state highways, within a metropolitan area to reduce unsafe interactions and their related crashes between drivers of large trucks and passenger vehicles. Using crash data, the driving behaviors most commonly associated with large truck and passenger vehicle crashes were identified. A public awareness campaign using media messaging and increased law enforcement was created targeting these associated behaviors. The frequency of these behaviors both before and after the public awareness campaign was determined through observation of traffic at 3 specific locations within the city. Each location had a sufficient volume of large truck and passenger traffic to observe frequent interactions. Pre- and postintervention data were compared using negative binomial regression with generalized estimating equations to evaluate whether the campaign was associated with a reduction in the identified driving behaviors. A comparison between crash data from before, during, and after the campaign and crashes during the same time periods in previous years did not show a significant difference (P =.081). The number of large trucks observed in traffic remained the same during pre- and postintervention periods (P =.625). The rates of negative interactions per 100 large trucks decreased for both large trucks and passenger vehicles after the intervention, with calculated rate ratios of 0.58 (95% confidence interval [CI], 0.48, 0.70) and 0.31 (95% CI, 0.20, 0.47). The greatest reduction was seen in passenger vehicles following too close, with a rate ratio of 0.21 (95% CI, 0.15, 0.30). Although designed for reducing crashes on highways, the TACT program can be an effective approach for improving driver behaviors on city streets.

  4. Application of sandwich honeycomb carbon/glass fiber-honeycomb composite in the floor component of electric car

    Science.gov (United States)

    Sukmaji, I. C.; Wijang, W. R.; Andri, S.; Bambang, K.; Teguh, T.

    2017-01-01

    Nowadays composite is a superior material used in automotive component due to its outstanding mechanical behavior. The sandwich polypropylene honeycomb core with carbon/glass fiber composite skin (SHCG) as based material in a floor component of electric car application is investigated in the present research. In sandwich structure form, it can absorb noise better compare with the conventional material [1]. Also in present paper, Finite Element Analysis (FEA) of SHCG as based material for floor component of the electric car is analyzed. The composite sandwich is contained with a layer uniform carbon fiber and mixing non-uniform carbon-glass fiber in upper and lower skin. Between skins of SHCG are core polypropylene honeycomb that it have good flexibility to form following dies profile. The variables of volume fraction ratio of carbon/glass fiber in SHCG skin are 20/80%, 30/70%, and 50/50%. The specimen of SHCG is tested using the universal testing machine by three points bending method refers to ASTM C393 and ASTM C365. The cross point between tensile strength to the volume fraction the mixing carbon/glass line and ratio cost line are the searched material with good mechanical performance and reasonable cost. The point is 30/70 volume fraction of carbon/glass fiber. The result of the testing experiment is become input properties of model structure sandwich in FEA simulation. FEA simulation approach is conducted to find critical strength and factor of complex safety geometry against varied distributed passenger loads of a floor component the electric car. The passenger loads variable are 80, 100, 150, 200, 250 and 300 kg.

  5. CuseCar--community car-sharing program : car sharing lessons learned.

    Science.gov (United States)

    2011-08-01

    CuseCar of Syracuse launched services in December 2008 with 3 Toyota Prius Hybrids. CuseCar initially, due to : concerns about availability, limited membership to Origination Sponsor Locations, which in turn developed few : members. In 2009 CuseCar o...

  6. Urban air chemistry and diesel vehicles emissions: Quantifying small and big hydrocarbons by CIMS to improve emission inventories

    Science.gov (United States)

    Jobson, B. T.; Derstroff, B.; Edtbauer, A.; VanderSchelden, G. S.; Williams, J.

    2017-10-01

    Emissions from vehicles are a major source of volatile organic compounds (VOCs) in urban environments. Photochemical oxidation of VOCs emitted from vehicle exhaust contributes to O3 and PM2.5 formation, harmful pollutants that major urban areas struggle to control. How will a shift to a diesel engine fleet impact urban air chemistry? Diesel vehicles are a growing fraction of the passenger vehicle fleet in Europe as a result of a deliberate policy to reduce energy consumption and CO2 emissions from the transportation sector (Sullivan et al., 2004). In countries such as France the diesel passenger fleet was already ∼50% of the total in 2009, up from 20% in 1995. Dunmore et al. (2015) have recently inferred that in London, HO radical loss rates to organic compounds is dominated by diesel engine emissions. In the US, increasingly more stringent vehicles emission standards and requirement for improved energy efficiency means spark ignition passenger vehicle emissions have declined significantly over the last 20 years, resulting in the urban diesel fleet traffic (freight trucks) having a growing importance as a source of vehicle pollution (McDonald et al., 2013). The recent scandal involving a major car manufacturer rigging emission controls for diesel passenger cars is a reminder that real world emissions of VOCs from diesel engines are not well understood nor thoroughly accounted for in air quality modeling.

  7. A forecast of household ownership and use of alternative fuel vehicles: A multiple discrete-continuous choice approach

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Jiwoon [Korea Energy Economics Institute, Naeson 2-dong, Uiwang-si, Gyeonggi-do, 437-713 (Korea); Jeong, Gicheol [Technology Management, Economics and Policy Program, 37-402, College of Engineering, Seoul National University, San 56-1, Sillim-dong, Gwanak-gu, Seoul, 151-744 (Korea); Kim, Yeonbae [Technology Management, Economics and Policy Program, 37-318, College of Engineering, Seoul National University, San 56-1, Sillim-dong, Gwanak-gu, South Seoul, 151-744 (Korea)

    2008-09-15

    The paper analyzes how adding alternative fuel passenger cars to the market will affect patterns in demand for passenger cars. We use conjoint analysis and a multiple discrete-continuous choice model to estimate consumer preferences regarding alternative fuel vehicles, and based on the estimates we conduct a simulation to analyze changing rates of ownership and use of variously fueled passenger cars under the effect of the introduction of alternative fuel passenger cars. In addition, we estimate changes in overall fuel consumption and the emission of pollutants. The results show that gasoline-fueled cars will still be most consumers' first choice, but alternative fuel passenger cars will nevertheless compete and offer a substitute for the purchase and use of gasoline-fueled or diesel-fueled cars. Finally, results show that adding alternative fuel cars to the market would effectively lower gasoline and diesel fuel consumption and the emission of pollutants. (author)

  8. A forecast of household ownership and use of alternative fuel vehicles: A multiple discrete-continuous choice approach

    International Nuclear Information System (INIS)

    Ahn, Jiwoon; Jeong, Gicheol; Kim, Yeonbae

    2008-01-01

    The paper analyzes how adding alternative fuel passenger cars to the market will affect patterns in demand for passenger cars. We use conjoint analysis and a multiple discrete-continuous choice model to estimate consumer preferences regarding alternative fuel vehicles, and based on the estimates we conduct a simulation to analyze changing rates of ownership and use of variously fueled passenger cars under the effect of the introduction of alternative fuel passenger cars. In addition, we estimate changes in overall fuel consumption and the emission of pollutants. The results show that gasoline-fueled cars will still be most consumers' first choice, but alternative fuel passenger cars will nevertheless compete and offer a substitute for the purchase and use of gasoline-fueled or diesel-fueled cars. Finally, results show that adding alternative fuel cars to the market would effectively lower gasoline and diesel fuel consumption and the emission of pollutants. (author)

  9. Study of Car Acceleration and Deceleration Characteristics at Dangerous Route FT050

    Science.gov (United States)

    Omar, N.; Prasetijo, J.; Daniel, B. D.; Abdullah, M. A. E.; Ismail, I.

    2018-04-01

    Individual vehicle acceleration and deceleration are important to generate vehicles speed profile. This study covered acceleration and deceleration characteristics of passenger car in Federal Route FT050 Jalan Batu Pahat-Ayer Hitam that was the top ranking dangerous road. Global Positioning System was used to record 10 cars speed to develop speed profile with clustering zone. At the acceleration manoeuver, the acceleration rate becomes lower as the drivers get near to desired speed. While, at deceleration manoeuver, vehicles with high speed needs more time to stop compare to low speed vehicle. This is because, the drivers need to accelerate more from zero speed to achieve desired speed and drivers need more distance and time to stop their vehicles. However, it was found out that 30% to 50% are driving in dangerous condition that was proven in clustering acceleration and deceleration speed profile. As conclusion, this excessive drivers are the factor that creating high risk in rear-end collision that inline FT050 as dangerous road in Malaysia

  10. 76 FR 6841 - Notice of Receipt of Petition for Decision That Nonconforming 2006 and 2007 Aston Martin Vantage...

    Science.gov (United States)

    2011-02-08

    ... Martin Vantage Passenger Cars Are Eligible for Importation AGENCY: National Highway Traffic Safety... Martin Vantage passenger cars are eligible for importation. SUMMARY: This document announces receipt by... 2007 Aston Martin Vantage passenger cars that were not originally manufactured to comply with all...

  11. Crash fatality and vehicle incompatibility in collisions between cars and light trucks or vans.

    Science.gov (United States)

    Ossiander, Eric M; Koepsell, Thomas D; McKnight, Barbara

    2014-12-01

    In crashes between a car and a light truck or van (LTV), car occupants are more likely to be killed than LTV occupants. The extent this is due to the greater harm imposed by LTVs on cars or the greater protection they offer their own occupants is not known. We conducted a case-control study of collisions between two passenger vehicles in the USA during 1990-2008. Cases were all decedents in fatal crashes (N=157,684); one control was selected from each crash in a national probability sample of crashes (N=379,458). Adjusted for the type of vehicle they were riding in and other confounders, occupants of vehicles colliding with any type of LTVs (categorised as compact sport utility vehicles (SUV), full-size SUVs, minivans, full-size vans, compact pickups and full-size pickups) were at higher risk of death compared with occupants colliding with cars. Adjusted for the type of vehicle they crashed with and other confounders, occupants of LTVs in a collision with any vehicle were at lower risk of death compared with car occupants. Compared with a crash between two cars, the overall RR of death in a crash between any of the other 27 different combinations of vehicle types was 1.0 or greater, except for crashes between two full-size pickups, where the RR of death was 0.9. Although LTVs protect their own occupants better than cars do, LTVs are associated with an excess total risk of death in crashes with cars or other LTVs. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  12. Particulates and noise exposure during bicycle, bus and car commuting: A study in three European cities

    NARCIS (Netherlands)

    Okokon, E.O.; Yli-Tuomi, T.; Turunen, A.W.; Taimisto, P.; Pennanen, A.; Vouitsis, I.; Samaras, Z.; Voogt, M.; Keuken, M.; Lanki, T.

    2017-01-01

    Background: In order to curb traffic-related air pollution and its impact on the physical environment, contemporary city commuters are encouraged to shift from private car use to active or public transport modes. However, personal exposures to particulate matter (PM), black carbon and noise during

  13. Influences of HVO and FAME on the combustion and emissions of modern passenger car diesel engines; Einfluesse von HVO und FAME auf die Verbrennung und Emissionen moderner PKW-Dieselmotoren

    Energy Technology Data Exchange (ETDEWEB)

    Stengel, Benjamin [Rostock Univ. (Germany). Lehrstuhl fuer Kolbenmaschinen und Verbrennungsmotoren; Sadlowski, Thomas; Wichmann, Volker; Harndorf, Horst

    2014-08-01

    In the framework of this study engine tests were performed with FAME (fatty acid methyl ester) and HVO (hydrotreated vegetable oil) as straight fuels using a EURO-VI passenger car diesel engine. Standard diesel fuel (EN 590) was used as reference. To analyze the impacts of the biofuels on the combustion process the heat release rates were calculated from in-cylinder pressure measurements using a single-zone model. Furthermore emissions were measured and ECU data was recorded. Results from engine tests showed that both HVO and FAME positively affect the combustion by a decreased ignition delay due to its higher cetane number. Raw exhaust emissions of soot were clearly reduced with HVO while CO and THC emissions showed minor reductions. During FAME operation ECU control settings were shifted due to its lower heating value. FAME showed reductions of soot by 60 % which is caused by the fuel's oxygen content while NO{sub x} emissions where slightly increased. However, a fuel adapted ECU calibration could optimize, e.g., the injection timing and EGR to further reduce emissions. Tailpipe emissions were not affected by HVO and FAME as the exhaust aftertreatment systems worked similarly efficient for all three fuels.

  14. 75 FR 1179 - Passenger Equipment Safety Standards; Front End Strength of Cab Cars and Multiple-Unit Locomotives

    Science.gov (United States)

    2010-01-08

    ... Metal Workers International Association (SMWIA); Tourist Railway Association, Inc.; Transport Canada... sleeping cars. Such trains are common on long- distance, intercity rail routes operated by Amtrak. On a...

  15. Evaluating a smartphone application to improve child passenger safety and fire safety knowledge and behaviour.

    Science.gov (United States)

    Omaki, Elise; Shields, Wendy C; McDonald, Eileen; Aitken, Mary E; Bishai, David; Case, James; Gielen, Andrea

    2017-02-01

    Although proven measures for reducing injury due to motor vehicle collision and residential fires exist, the number of families properly and consistently using child passenger restraints and smoke alarms remains low. This paper describes the design of the Safety In Seconds (SIS) 2.0 study, which aims to evaluate the impact of a smartphone app on parents' use of child restraints and smoke alarms. SIS is a multisite randomised controlled trial. Participants are parents of children aged 4-7 years who are visiting the Pediatric Emergency Department or Pediatric Trauma Service. Parents are randomised to receive tailored education about child passenger safety or about fire safety via the SIS smartphone app. A baseline and two follow-up surveys at 3 months and 6 months are conducted. Primary outcomes are: (1) having the correct child restraint for the child's age and size; (2) restraining the child in the back seat of the car; (3) buckling the child up for every ride; (4) having the restraint inspected by a child passenger safety technician; (5) having a working smoke alarm on every level of the home; (6) having hard-wired or lithium battery smoke alarms; (7) having and (8) practising a fire escape plan. Finding ways to communicate with parents about child passenger and fire safety continues to be a research priority. This study will contribute to the evidence about how to promote benefits of proper and consistent child restraint and smoke alarm use. NCT02345941; Pre-results. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

  16. Car spring by natural gas. Dynamic, economical, proper; Mit Erdgas in den Autofruehling. Dynamisch, wirtschaftlich, sauber

    Energy Technology Data Exchange (ETDEWEB)

    Holtmeier, Gerhard [Initiativkreis Erdgas als Kraftstoff - Deutschland e.V., Leipzig (Germany); VNG - Verbundnetz Gas AG, Leipzig (Germany)

    2009-06-02

    Natural gas passenger cars are cruising into the spring of automotive year 2009. Rolling off the production lines since March the world's first mass-produced natural gas turbo vehicles have rung in the era of natural gas powered mobility. They reconcile the joy of driving with economy and environmental friendliness. Apart from being fit for everyday use they also do their job in motor sports, as demonstrated by two tuned natural-gas powered VW Scirocco cars that participated in the 24-hour race on the Nuerburg Ring in late May. To bring momentum to the market is also the task of ''erdgas mobil'', a newly founded sales company for natural gas and natural gas powered vehicles, which started operations in April of 2009.

  17. Indoor PM1, PM2.5, PM10 and outdoor PM2.5 concentrations in primary schools in Sari, Iran.

    Science.gov (United States)

    Mohammadyan, Mahmoud; Shabankhani, Bijan

    2013-09-01

    This study was carried out to determine the distribution of particles in classrooms in primary schools located in the centre of the city of Sari, Iran and identify the relationship between indoor classroom particle levels and outdoor PM2.5 concentrations. Outdoor PM2.5 and indoor PM1, PM2.5, and PM10 were monitored using a real-time Micro Dust Pro monitor and a GRIMM monitor, respectively. Both monitors were calibrated by gravimetric method using filters. The Kolmogorov-Smirnov test showed that all indoor and outdoor data fitted normal distribution. Mean indoor PM1, PM2.5, PM10 and outdoor PM2.5 concentrations for all of the classrooms were 17.6 μg m(-3), 46.6 μg m(-3), 400.9 μg m(-3), and 36.9 μg m(-3), respectively. The highest levels of indoor and outdoor PM2.5 concentrations were measured at the Shahed Boys School (69.1 μg m(-3) and 115.8 μg m(-3), respectively). The Kazemi school had the lowest levels of indoor and outdoor PM2.5 (29.1 μg m(-3) and 15.5 μg m(-3), respectively). In schools located near both main and small roads, the association between indoor fine particle (PM2.5 and PM1) and outdoor PM2.5 levels was stronger than that between indoor PM10 and outdoor PM2.5 levels. Mean indoor PM2.5 and PM10 and outdoor PM2.5 were higher than the standards for PM2.5 and PM10, and there was a good correlation between indoor and outdoor fine particle concentrations.

  18. Determinants of injuries in passenger vessel accidents.

    Science.gov (United States)

    Yip, Tsz Leung; Jin, Di; Talley, Wayne K

    2015-09-01

    This paper investigates determinants of crew and passenger injuries in passenger vessel accidents. Crew and passenger injury equations are estimated for ferry, ocean cruise, and river cruise vessel accidents, utilizing detailed data of individual vessel accidents that were investigated by the U.S. Coast Guard during the time period 2001-2008. The estimation results provide empirical evidence (for the first time in the literature) that crew injuries are determinants of passenger injuries in passenger vessel accidents. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. International Passenger and Freight Report

    Data.gov (United States)

    Department of Transportation — The International Passenger and Freight report is a summarization of all passengers and all freight transported between the U.S. and foreign countries combined, with...

  20. 76 FR 57103 - Reports, Forms and Recordkeeping Requirements Agency Information Collection Activity Under OMB...

    Science.gov (United States)

    2011-09-15

    ... Federal Motor Vehicle Theft Prevention Standard was extended to include all passenger cars and... Vehicle Theft Prevention Standard (Part 541), all passenger cars, and multipurpose passenger vehicles with..., 565 and 567. Part 541 The Motor Vehicle Information and Cost Savings Act was amended by the Anti-Car...

  1. Black Carbon and Particulate Matter (PM2.5) Concentrations in New York City’s Subway Stations

    Science.gov (United States)

    2015-01-01

    The New York City (NYC) subway is the main mode of transport for over 5 million passengers on an average weekday. Therefore, airborne pollutants in the subway stations could have a significant impact on commuters and subway workers. This study looked at black carbon (BC) and particulate matter (PM2.5) concentrations in selected subway stations in Manhattan. BC and PM2.5 levels were measured in real time using a Micro-Aethalometer and a PDR-1500 DataRAM, respectively. Simultaneous samples were also collected on quartz filters for organic and elemental carbon (OC/EC) analysis and on Teflon filters for gravimetric and trace element analysis. In the underground subway stations, mean real time BC concentrations ranged from 5 to 23 μg/m3, with 1 min average peaks >100 μg/m3, while real time PM2.5 levels ranged from 35 to 200 μg/m3. Mean EC levels ranged from 9 to 12.5 μg/m3. At street level on the same days, the mean BC and PM2.5 concentrations were below 3 and 10 μg/m3, respectively. This study shows that both BC soot and PM levels in NYC’s subways are considerably higher than ambient urban street levels and that further monitoring and investigation of BC and PM subway exposures are warranted. PMID:25409007

  2. Heart rate variability (HRV) and muscular system activity (EMG) in cases of crash threat during simulated driving of a passenger car.

    Science.gov (United States)

    Zużewicz, Krystyna; Roman-Liu, Danuta; Konarska, Maria; Bartuzi, Paweł; Matusiak, Krzysztof; Korczak, Dariusz; Lozia, Zbigniew; Guzek, Marek

    2013-10-01

    The aim of the study was to verify whether simultaneous responses from the muscular and circulatory system occur in the driver's body under simulated conditions of a crash threat. The study was carried out in a passenger car driving simulator. The crash was included in the driving test scenario developed in an urban setting. In the group of 22 young male subjects, two physiological signals - ECG and EMG were continuously recorded. The length of the RR interval in the ECG signal was assessed. A HRV analysis was performed in the time and frequency domains for 1-minute record segments at rest (seated position), during undisturbed driving as well as during and several minutes after the crash. For the left and right side muscles: m. trapezius (TR) and m. flexor digitorum superficialis (FDS), the EMG signal amplitude was determined. The percentage of maximal voluntary contraction (MVC) was compared during driving and during the crash. As for the ECG signal, it was found that in most of the drivers changes occurred in the parameter values reflecting HRV in the time domain. Significant changes were noted in the mean length of RR intervals (mRR). As for the EMG signal, the changes in the amplitude concerned the signal recorded from the FDS muscle. The changes in ECG and EMG were simultaneous in half of the cases. Such parameters as mRR (ECG signal) and FDS-L amplitude (EMG signal) were the responses to accident risk. Under simulated conditions, responses from the circulatory and musculoskeletal systems are not always simultaneous. The results indicate that a more complete driver's response to a crash in road traffic is obtained based on parallel recording of two physiological signals (ECG and EMG).

  3. Medical emergencies on large passenger ships without doctors: the Oslo-Kiel-Oslo ferry experience.

    Science.gov (United States)

    Holt, Thor-Erik; Tveten, Agnar; Dahl, Eilif

    2017-01-01

    The Oslo-Kiel-Oslo route is currently the only direct ferry crossing between Norway and Germany, covered by 2 cruise-and-cars ferries carrying about 2,600 passengers each and sailing every day (20 h at sea, 4 h in port). Unlike most ocean going cruise vessels, they are not required to carry a physician but an on-board paramedic handles medical emergencies. The aim of the study was to provide data on medical emergencies leading to helicopter evacuations (helivacs) or other urgent transfers to facilities ashore from the two ferries during a 3-year period. Data about the ferries, passengers, crew, helivacs and other medical transfers were collected from official company statistics and the paramedics' transfer reports. A total of 169 persons, including 14 (8.3%) crewmembers, were transferred from the ferries to land-based facilities by ambulance while alongside (n = 80; 47.3%) or evacuated by helicopter (n = 85; 50.3%) and rescue boat (n = 4; 2.4%) during the 3-year period. Transfer destinations were Denmark (n = 53), Germany (n = 49), Norway (n = 48) and Sweden (n = 19). The passenger helivac rate was 2.4 per 100,000 passenger-days. One person was airlifted from a ferry every 2 weeks. Among helivacs, 40% were heart-related, and more cardiac cases were airlifted than transferred by ambulance in port. All helivac requests were made after discussion between the ferry's paramedic and telemedical doctors ashore and agreement that the medical challenge exceeded the ferry's capability. This close cooperation kept the threshold for arranging helivacs from the ferries low, enabling short transport times to land-based facilities for critically ill patients. Further studies, including feedback from the receiving hospitals, are needed to determine measures that can reduce possible helicopter overutilisation without compromising patient safety and outcome.

  4. Telemedical Advice to Long Distance Passenger Ferries

    DEFF Research Database (Denmark)

    Jensen, Olaf Chresten; Bøggild, Niels Bo; Kristensen, Søren

    consultations with passenger ferries to identify areas for possible improvements. Methods: Data from the journals for one year from Radio Medical Denmark consultations with the medical Data from the journals for one year from Radio Medical Denmark consultations with the medical responsible officers on passenger...... ferries was analysed retrospectively. Results: Two hundred and fourteen RM records, 73% among passenger and 27% among crewmember Two hundred and fourteen RM records, 73% among passenger and 27% among crewmember patients were analysed. Passenger patients were generally older and more serious ill than...

  5. Suppression of chaotic vibrations in a nonlinear half-car model

    Energy Technology Data Exchange (ETDEWEB)

    Tusset, Ângelo Marcelo, E-mail: tusset@utfpr.edu.br, E-mail: piccirillo@utfpr.edu.br, E-mail: fcjanzen@utfpr.edu.br, E-mail: wagner-barth@hotmail.com; Piccirillo, Vinícius, E-mail: tusset@utfpr.edu.br, E-mail: piccirillo@utfpr.edu.br, E-mail: fcjanzen@utfpr.edu.br, E-mail: wagner-barth@hotmail.com; Janzen, Frederic Conrad, E-mail: tusset@utfpr.edu.br, E-mail: piccirillo@utfpr.edu.br, E-mail: fcjanzen@utfpr.edu.br, E-mail: wagner-barth@hotmail.com; Lenz, Wagner Barth, E-mail: tusset@utfpr.edu.br, E-mail: piccirillo@utfpr.edu.br, E-mail: fcjanzen@utfpr.edu.br, E-mail: wagner-barth@hotmail.com [UTFPR- PONTA GROSSA, PR (Brazil); Balthazar, José Manoel, E-mail: jmbaltha@rc.unesp.br [UNESP-BAURU, SP (Brazil); Fonseca Brasil, Reyolando M. L. R. da, E-mail: reyolando.brasil@ufabc.edu.br [UFABC-SANTO ANDRE, SP (Brazil)

    2014-12-10

    The present work investigates the nonlinear response of a half-car model. The disturbances of the road are assumed to be sinusoidal. After constructing the bifurcation diagram, we using the 0-1 test for identify the chaotic motion. The principal objective of this study is to eliminate the chaotic behaviour of the chassis and reduce its vibration, and for this reason a control system for semi-active vehicle suspension with magnetorheological damper is proposed. The control mechanism is designed based on SDRE technique, where the control parameter is the voltage applied to the coil of the damper. Numerical results show that the proposed control method is effective in significantly reducing of the chassis vibration, increasing therefore, passenger comfort.

  6. The ability of flexible car bonnets to mitigate the consequences of frontal impact with pedestrians

    Science.gov (United States)

    Stanisławek, Sebastian; Niezgoda, Tadeusz

    2018-01-01

    The paper presents the results of numerical research on a vehicle representing a Toyota Yaris passenger sedan hitting a pedestrian. A flexible car body is suggested as an interesting way to increase safety. The authors present a simple low-cost bonnet buffer concept that may mitigate the effects of frontal impact. Computer simulation was the method chosen to solve the problem efficiently. The Finite Element Method (FEM) implemented in the LS-DYNA commercial code was used. The testing procedure was based on the Euro NCAP protocol. A flexible bonnet buffer shows its usefulness in preventing casualties in typical accidents. In the best scenario, the HIC15 parameter is only 380 when such a buffer is installed. In comparison, an accident involving a car without any protection produces an HIC15 of 970, which is very dangerous for pedestrians.

  7. Parents as passengers during pediatric transport.

    Science.gov (United States)

    Lewis, M M; Holditch-Davis, D; Brunssen, S

    1997-01-01

    The transport environment presents a unique setting in which the feasibility, advantages, and disadvantages of passengers accompanying a patient must be assessed carefully. The purpose of this study was to describe the current practice of including parents as passengers during pediatric interfacility transport. One-hundred-eighty-eight critical care transport programs in the United States responded to a voluntary mail survey, providing information about current policies, practices, and crew perceptions of the advantages and disadvantages of carrying parents as passengers. Extra seating for passengers was available in 96% of ambulances, 86% of fixed-wing aircraft, and 54% of helicopters used for pediatric transport. Parents traveled as passengers in all types of vehicles; most frequently in ambulances and fixed-wing aircraft. Twenty percent of helicopter programs allowed parent passengers on more than half of their pediatric transports in this vehicle. Advantages of parent passengers included emotional benefit for the parent and child, availability of parents for history and consent, good public relations, and having the parent present if the child dies. Disadvantages included potential parent anxiety, crew distraction, and space limitations. This study reflects the widely diverse policies, practices, and opinions relevant to this topic and confirms a need for further study.

  8. The Analysis of Competitive Strategy and Suggestions for Didi under the Background of the New Car-hailing Regulation

    Science.gov (United States)

    Wang, Tingting; Zhao, Lei

    2017-10-01

    The emergence of car-hailing service satisfies the need of public travel in Internet era. Didi—the representative of car-hailing service, provides users with cost-effective service and great travel experience and quickly became the leader in the field of mobile travel depending on its price advantage, market segmentation, fast respond and some other competitive strategies. However, the promulgation of the new car-hailing regulation brings many challenges to Didi. After the new regulation, it is hard for Didi to gap away significantly from its competitors in scale and price. Thus the differentiated service is the competitive focus for all platforms. So there is an urgent need for Didi to do something to make difference, such as improving the interface design of the platform and the process of order allocation, establishing exclusive ‘station’, increasing the interaction between drivers and passengers. By doing so, Didi can reduce the information asymmetry and increase the user engagement and loyalty with high quality service.

  9. Polycyclic aromatic hydrocarbons (PAH) and diesel engine emission (elemental carbon) inside a car and a subway train.

    Science.gov (United States)

    Fromme, H; Oddoy, A; Piloty, M; Krause, M; Lahrz, T

    1998-06-30

    Significant concentrations of potentially harmful substances can be present in the interior of vehicles. The main sources of PAHs and elemental carbon (EC) inside a car are likely to be combustion emissions, especially from coal and traffic. The same sources can also be important for the interior of a subway train for which there are specific sources in the tunnel system, for example diesel engines. Twice, in summer 1995 and winter 1996 polycyclic aromatic hydrocarbons (PAH) and diesel motor emission (estimated as elemental carbon) were determined in the interior of a car (a 2-year-old VW Golf with a three-way catalytic converter) and in the passenger compartment of a subway train (below ground). On each sampling day (in total 16 daily measurements in the car and 16 in the subway) the substances were determined in the breathing zone of the passengers from 07:00 h to 16:00 h under different meteorologic conditions (winter- and summertime). The car followed the route of the subway from the western Berlin borough of Spandau to the south-eastern borough of Neukölln, and back. The sampling represented a realistic exposure model for driving in a high traffic and polluted urban area. The electric subway train (also 2 years in use) connected the same parts of Berlin (31 km underground). The mean values obtained during the two measurement periods (summer/winter) inside the car were 1.0 and 3.2 ng/m3 for benzo[a]pyrene, 10.2 and 28.7 ng/m3 for total-measured-PAHs, 14.1 and 8.2 micrograms/m3 for EC and in the subway 0.7 and 4.0 ng/m3 for benzol[a]pyrene, 30.2 and 67.5 ng/m3 for total PAHs, 109 and 6.9 micrograms/m3 for EC. A comparison between subway and car exposures shows significantly higher concentrations of PAHs in the subway train, which can be explained by relatively high concentrations of fluoranthene and pyrene in the subway. So far a satisfactory explanation has not been found, but one source might be the wooden railway ties which were formerly preserved with tar

  10. Dynamic Passenger Assignment during Disruptions in Railway Systems

    NARCIS (Netherlands)

    Zhu, Y.; Goverde, R.M.P.

    2017-01-01

    Passenger-oriented rescheduling problems receive increasing attention. However, the passenger assignment models used for evaluating the rescheduling solutions are usually simplified by many assumptions. To estimate passenger inconvenience more accurately, this paper establishes a dynamic passenger

  11. 75 FR 54000 - Reports, Forms, and Record keeping Requirements

    Science.gov (United States)

    2010-09-02

    ..., including the use of appropriate automated, electronic, mechanical, or other technological collection... vehicles (including passenger cars, certain small buses, all light trucks and multipurpose passenger.... Manufacturers of new passenger motor vehicles, including passenger cars, certain small buses, and light trucks...

  12. Access improvement to aircraft passengers' hand luggage.

    Science.gov (United States)

    Alberda, W; Kampinga, O; Kassels, R; van Kester, R; Noriega, J; Vink, P

    2015-01-01

    Efficient use of space and passenger comfort in aircraft interiors are major issues. There is not much research available about the flying experience regarding passengers' personal belongings. The objective of this study is to explore concepts within the current aircraft seats which improve the passenger experience related to their personal belongings like wallets, mobile phones and laptops. Through on-site observations, interviews and online questionnaires, data regarding the number of personal belongings taken into the airplane and opinions about access to hand luggage were gathered. These data were used to develop different concepts to optimize the aircraft interior, which were evaluated by passengers. Almost every passenger carries a phone (88%), wallet (94%), travel documents (98%) and keys (76%) with them and they like to have these stored close by. Passengers rate the concept that provides integrated storage in the tray table of the aircraft seat the best. Extra storage possibility in the table-tray seems a promising solution according to the passengers.

  13. Prediction of dynamic Rankine Cycle waste heat recovery performance and fuel saving potential in passenger car applications considering interactions with vehicles’ energy management

    International Nuclear Information System (INIS)

    Horst, Tilmann Abbe; Tegethoff, Wilhelm; Eilts, Peter; Koehler, Juergen

    2014-01-01

    Highlights: • Method for evaluating fuel saving potential of vehicle waste heat recovery systems. • Analysis of interactions between waste heat recovery system and vehicle. • Evaluation of fuel saving potential in dynamic motorway driving scenario. • Parameter study for increasing fuel saving potential of integrated system. - Abstract: Waste heat recovery (WHR) by means of a Rankine Cycle is a promising approach for achieving reductions in fuel consumption and, as a result, exhaust emissions of passenger car engines. To find the best compromise between complexity and fuel saving potential, methods for predicting the WHR performance for different system configurations and stationary as well as dynamic driving scenarios are needed. Since WHR systems are usually not included in today’s car concepts, they are mostly designed as add-on systems. As a result their integration may lead to negative interactions due to increased vehicle weight, engine backpressure and cooling demand. These effects have to be considered when evaluating the fuel saving potential. A new approach for predicting WHR performance and fuel saving potential was developed and is presented in this paper. It is based on simple dynamic models of a system for recovering exhaust gas waste heat and its interfaces with the vehicle: the exhaust system for heat input, the on-board electric system for power delivery and the engine cooling system for heat rejection. The models are validated with test bench measurements of the cycle components. A study of fuel saving potential in an exemplary dynamic motorway driving scenario shows the effect of vehicle integration: while the WHR system could improve fuel economy by 3.4%, restrictions in power output due to the architecture of the on-board electric system, package considerations, increased weight, cooling demand and exhaust gas backpressure lead to a reduction of fuel saving potential by 60% to 1.3%. A parameter study reveals that, in addition to weight

  14. Network structure of subway passenger flows

    Science.gov (United States)

    Xu, Q.; Mao, B. H.; Bai, Y.

    2016-03-01

    The results of transportation infrastructure network analyses have been used to analyze complex networks in a topological context. However, most modeling approaches, including those based on complex network theory, do not fully account for real-life traffic patterns and may provide an incomplete view of network functions. This study utilizes trip data obtained from the Beijing Subway System to characterize individual passenger movement patterns. A directed weighted passenger flow network was constructed from the subway infrastructure network topology by incorporating trip data. The passenger flow networks exhibit several properties that can be characterized by power-law distributions based on flow size, and log-logistic distributions based on the fraction of boarding and departing passengers. The study also characterizes the temporal patterns of in-transit and waiting passengers and provides a hierarchical clustering structure for passenger flows. This hierarchical flow organization varies in the spatial domain. Ten cluster groups were identified, indicating a hierarchical urban polycentric structure composed of large concentrated flows at urban activity centers. These empirical findings provide insights regarding urban human mobility patterns within a large subway network.

  15. Cars and fuels for tomorrow: A comparative assessment

    International Nuclear Information System (INIS)

    Aahman, Max; Nilsson, Lars J.; Johansson, Bengt

    2001-01-01

    Light duty vehicles, i.e. passenger cars and light trucks, account for approximately half of global transportation energy demand and, thus, a major share of carbon dioxide and other emissions from the transport sector. Energy consumption in the transport sector is expected to grow in the future, especially in developing countries. Cars with alternative powertrains to internal combustion engines (notably battery, hybrid and fuel-cell powertrains), in combination with potentially low carbon electricity or alternative fuels (notably hydrogen and methanol), can reduce energy demand by at least 50%, and carbon dioxide and regulated emissions much further. This article presents a comparative technical and economic assessment of promising future fuel/vehicle combinations. There are several promising technologies but no obvious winners. However, the electric drivetrain is a common denominator in the alternative powertrains and continued cost reductions are important for widespread deployment in future vehicles. Development paths from current fossil fuel based systems to future carbon-neutral supply systems appear to be flexible and a gradual phasing-in of new powertrains and carbon-neutral fluid fuels or electricity is technically possible. Technology development drivers and vehicle manufacturers are found mainly in industrialised countries, but developing countries represent a growing market and may have an increasingly important role in shaping the future. (author)

  16. Outdoor particulate matter (PM and associated cardiovascular diseases in the Middle East

    Directory of Open Access Journals (Sweden)

    Zeina Nasser

    2015-08-01

    Full Text Available Air pollution is a widespread environmental concern. Considerable epidemiological evidence indicates air pollution, particularly particulate matter (PM, as a major risk factor for cardiovascular diseases (CVD in the developed countries. The main objective of our review is to assess the levels and sources of PM across the Middle East area and to search evidence for the relationship between PM exposure and CVD. An extensive review of the published literature pertaining to the subject (2000–2013 was conducted using PubMed, Medline and Google Scholar databases. We reveal that low utilization of public transport, ageing vehicle fleet and the increasing number of personal cars in the developing countries all contribute to the traffic congestion and aggravate the pollution problem. The annual average values of PM pollutants in the Middle East region are much higher than the World Health Organization 2006 guidelines (PM2.5 = 10 μg/m3, PM10 = 20 μg/m3. We uncover evidence on the association between PM and CVD in 4 Middle East countries: Iran, Kingdom of Saudi Arabia, Qatar and the United Arab Emirates. The findings are in light of the international figures. Ambient PM pollution is considered a potential risk factor for platelet activation and atherosclerosis and has been found to be linked with an increased risk for mortality and hospital admissions due to CVD. This review highlights the importance of developing a strategy to improve air quality and reduce outdoor air pollution in the developing countries, particularly in the Middle East. Future studies should weigh the potential impact of PM on the overall burden of cardiac diseases.

  17. Teen Drivers' Perceptions of Their Peer Passengers: Qualitative Study.

    Science.gov (United States)

    Ehsani, Johnathon P; Haynie, Denise L; Luthers, Christina; Perlus, Jessamyn; Gerber, Eli; Ouimet, Marie Claude; Klauer, Sheila G; Simons-Morton, Bruce

    The presence of peer passengers increases teenage drivers' fatal crash risk. Distraction and social influence are the two main factors that have been associated with increased risk. Teen drivers' perceptions of their peer passengers on these factors could inform our understanding of the conditions under which peer passengers increase crash risk or promote safer driving. The purpose of this study was to examine teen drivers' perceptions of their peer passengers on distraction and social influence. A convenience sample of male and female drivers participated in a semi-structured interview that included questions on their perceptions of the effects of peer passengers on driving on distraction and social influence. The analysis of the interviews was guided by a grounded theory approach. Teenage drivers were aware of the risk that peer passengers posed. Some described having passengers in the vehicle as distracting, and recognized that the level of distraction increased with the number of passengers in the vehicle. Drivers that felt responsible for the safety of their peer passengers described strategies they used to control the in-vehicle environment. Drivers described driving with passengers as a performance, and articulated direct and indirect sources of pressure, gender norms, and unspoken expectations of their passengers as influencing their driving behavior. The influence of passengers is situation specific and dependent on whom the passenger(s) may be. Passenger influence may be either protective or harmful, depending on the circumstances. Some passengers exert direct influence, but often their influence appears more indirect and subtle.

  18. Personal exposure to particulate matter in commuters using different transport modes (bus, bicycle, car and subway) in an assigned route in downtown Santiago, Chile.

    Science.gov (United States)

    Suárez, Liliana; Mesías, Stephanie; Iglesias, Verónica; Silva, Claudio; Cáceres, Dante D; Ruiz-Rudolph, Pablo

    2014-05-01

    The objective of this study was to compare personal exposure to particulate matter (fine and ultrafine particles) in commuters using different transport modes (bicycle, bus, car and subway) in a busy, assigned route in downtown Santiago, Chile. Volunteers carrying personal samplers completed scheduled commutes during the morning rush hours, while central site measurements were conducted in parallel. A total of 137 valid commutes were assessed. The impact of central site, traffic and other variables was explored with regression models. PM2.5 personal concentrations were equal to or slightly above central site measurements, while UFP personal concentrations were above them. Regression models showed impacts of both background levels and traffic emissions on personal PM2.5 and UFP exposure. Traffic impacts varied with transport modes. Estimates of traffic impacts on personal PM2.5 exposure were 2.0, 13.0, 16.9 and 17.5 μg m(-3), for car, bicycle, subway and bus, respectively; while for UFP exposure were 8400, 16 200, 25 600 and 30 100 counts per cm(3), for subway, car, bicycle and bus, respectively. After controlling the central site and transport mode, higher temperatures increased PM2.5 exposure and decreased UFP ones, while the wind direction affected UFP personal exposure. In conclusion, we found significant impacts of both central site background measurements and traffic emissions on personal exposure of volunteer commuters in an assigned route in Santiago, with impacts varying with transport modes.

  19. 49 CFR 571.401 - Standard No. 401; Interior trunk release.

    Science.gov (United States)

    2010-10-01

    .... Requirements. S4.1 Each passenger car with a trunk compartment must have an automatic or manual release... possible for a person trapped inside the trunk compartment of a passenger car to escape from the compartment. S2. Application. This standard applies to passenger cars that have a trunk compartment. This...

  20. 49 CFR 571.204 - Standard No. 204; Steering control rearward displacement.

    Science.gov (United States)

    2010-10-01

    ... September 1, 1991. When a passenger car or a truck, bus, or multipurpose passenger vehicle with a gross... manufactured on or after September 1, 1991. When a passenger car or a truck, bus or multipurpose passenger... the steering control into the passenger compartment to reduce the likelihood of chest, neck, or head...

  1. Research on the recycling industry development model for typical exterior plastic components of end-of-life passenger vehicle based on the SWOT method.

    Science.gov (United States)

    Zhang, Hongshen; Chen, Ming

    2013-11-01

    In-depth studies on the recycling of typical automotive exterior plastic parts are significant and beneficial for environmental protection, energy conservation, and sustainable development of China. In the current study, several methods were used to analyze the recycling industry model for typical exterior parts of passenger vehicles in China. The strengths, weaknesses, opportunities, and challenges of the current recycling industry for typical exterior parts of passenger vehicles were analyzed comprehensively based on the SWOT method. The internal factor evaluation matrix and external factor evaluation matrix were used to evaluate the internal and external factors of the recycling industry. The recycling industry was found to respond well to all the factors and it was found to face good developing opportunities. Then, the cross-link strategies analysis for the typical exterior parts of the passenger car industry of China was conducted based on the SWOT analysis strategies and established SWOT matrix. Finally, based on the aforementioned research, the recycling industry model led by automobile manufacturers was promoted. Copyright © 2013 Elsevier Ltd. All rights reserved.

  2. Impact of excess NOx emissions from diesel cars on air quality, public health and eutrophication in Europe

    Science.gov (United States)

    Jonson, J. E.; Borken-Kleefeld, J.; Simpson, D.; Nyíri, A.; Posch, M.; Heyes, C.

    2017-09-01

    Diesel cars have been emitting four to seven times more NOx in on-road driving than in type approval tests. These ‘excess emissions’ are a consequence of deliberate design of the vehicle’s after-treatment system, as investigations during the ‘Dieselgate’ scandal have revealed. Here we calculate health and environmental impacts of these excess NOx emissions in all European countries for the year 2013. We use national emissions reported officially under the UNECE Convention for Long-range Transport of Atmospheric Pollutants and employ the EMEP MSC-W Chemistry Transport Model and the GAINS Integrated Assessment Model to determine atmospheric concentrations and resulting impacts. We compare with impacts from hypothetical emissions where light duty diesel vehicles are assumed to emit only as much as their respective type approval limit value or as little as petrol cars of the same age. Excess NO2 concentrations can also have direct health impacts, but these overlap with the impacts from particulate matter (PM) and are not included here. We estimate that almost 10 000 premature deaths from PM2.5 and ozone in the adult population (age >30 years) can be attributed to the NOx emissions from diesel cars and light commercial vehicles in EU28 plus Norway and Switzerland in 2013. About 50% of these could have been avoided if diesel limits had been achieved also in on-road driving; and had diesel cars emitted as little NOx as petrol cars, 80% of these premature deaths could have been avoided. Ecosystem eutrophication impacts (critical load exceedances) from the same diesel vehicles would also have been reduced at similar rates as for the health effects.

  3. 77 FR 31910 - Reports, Forms, and Recordkeeping Requirements

    Science.gov (United States)

    2012-05-30

    ... appropriate automated, electronic, mechanical, or other technological collection techniques or other forms of... manufacturers of passenger cars and of trucks, buses and multipurpose passenger vehicles with a gross vehicle... there are 21 manufacturers of passenger cars, multipurpose passenger vehicles, trucks, and buses with a...

  4. 76 FR 4298 - Certain New Pneumatic Off-the-Road Tires From the People's Republic of China: Notice of...

    Science.gov (United States)

    2011-01-25

    ... use, including passenger cars, race cars, station wagons, sport utility vehicles, minivans, mobile...--Identifies a tire intended primarily for service on passenger cars; LT--Identifies a tire intended primarily...

  5. 75 FR 64259 - Certain New Pneumatic Off-the-Road Tires From the People's Republic of China: Preliminary Results...

    Science.gov (United States)

    2010-10-19

    ... use, including passenger cars, race cars, station wagons, sport utility vehicles, minivans, mobile...--Identifies a tire intended primarily for service on passenger cars; LT--Identifies a tire intended primarily...

  6. 46 CFR 115.910 - Passenger Ship Safety Certificate.

    Science.gov (United States)

    2010-10-01

    ...) The route specified on the Certificate of Inspection and the SOLAS Passenger Ship Safety Certificate... 46 Shipping 4 2010-10-01 2010-10-01 false Passenger Ship Safety Certificate. 115.910 Section 115... MORE THAN 150 PASSENGERS OR WITH OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS INSPECTION AND...

  7. Measurement of the charge asymmetry in $B^{\\pm}\\rightarrow \\phi K^{\\pm}$ and search for $B^{\\pm}\\rightarrow \\phi \\pi^{\\pm}$ decays

    CERN Document Server

    Aaij, R; Adinolfi, M; Adrover, C; Affolder, A; Ajaltouni, Z; Albrecht, J; Alessio, F; Alexander, M; Ali, S; Alkhazov, G; Alvarez Cartelle, P; Alves Jr, A A; Amato, S; Amerio, S; Amhis, Y; Anderlini, L; Anderson, J; Andreassen, R; Andrews, J E; Appleby, R B; Aquines Gutierrez, O; Archilli, F; Artamonov, A; Artuso, M; Aslanides, E; Auriemma, G; Baalouch, M; Bachmann, S; Back, J J; Badalov, A; Baesso, C; Balagura, V; Baldini, W; Barlow, R J; Barschel, C; Barsuk, S; Barter, W; Bauer, Th; Bay, A; Beddow, J; Bedeschi, F; Bediaga, I; Belogurov, S; Belous, K; Belyaev, I; Ben-Haim, E; Bencivenni, G; Benson, S; Benton, J; Berezhnoy, A; Bernet, R; Bettler, M -O; van Beuzekom, M; Bien, A; Bifani, S; Bird, T; Bizzeti, A; Bjørnstad, P M; Blake, T; Blanc, F; Blouw, J; Blusk, S; Bocci, V; Bondar, A; Bondar, N; Bonivento, W; Borghi, S; Borgia, A; Bowcock, T J V; Bowen, E; Bozzi, C; Brambach, T; van den Brand, J; Bressieux, J; Brett, D; Britsch, M; Britton, T; Brook, N H; Brown, H; Bursche, A; Busetto, G; Buytaert, J; Cadeddu, S; Callot, O; Calvi, M; Calvo Gomez, M; Camboni, A; Campana, P; Campora Perez, D; Carbone, A; Carboni, G; Cardinale, R; Cardini, A; Carranza-Mejia, H; Carson, L; Carvalho Akiba, K; Casse, G; Castillo Garcia, L; Cattaneo, M; Cauet, Ch; Cenci, R; Charles, M; Charpentier, Ph; Chen, P; Cheung, S -F; Chiapolini, N; Chrzaszcz, M; Ciba, K; Cid Vidal, X; Ciezarek, G; Clarke, P E L; Clemencic, M; Cliff, H V; Closier, J; Coca, C; Coco, V; Cogan, J; Cogneras, E; Collins, P; Comerma-Montells, A; Contu, A; Cook, A; Coombes, M; Coquereau, S; Corti, G; Couturier, B; Cowan, G A; Craik, D C; Cruz Torres, M; Cunliffe, S; Currie, R; D'Ambrosio, C; David, P; David, P N Y; Davis, A; De Bonis, I; De Bruyn, K; De Capua, S; De Cian, M; De Miranda, J M; De Paula, L; De Silva, W; De Simone, P; Decamp, D; Deckenhoff, M; Del Buono, L; Déléage, N; Derkach, D; Deschamps, O; Dettori, F; Di Canto, A; Dijkstra, H; Dogaru, M; Donleavy, S; Dordei, F; Dosil Suárez, A; Dossett, D; Dovbnya, A; Dupertuis, F; Durante, P; Dzhelyadin, R; Dziurda, A; Dzyuba, A; Easo, S; Egede, U; Egorychev, V; Eidelman, S; van Eijk, D; Eisenhardt, S; Eitschberger, U; Ekelhof, R; Eklund, L; El Rifai, I; Elsasser, Ch; Falabella, A; Färber, C; Farinelli, C; Farry, S; Ferguson, D; Fernandez Albor, V; Ferreira Rodrigues, F; Ferro-Luzzi, M; Filippov, S; Fiore, M; Fitzpatrick, C; Fontana, M; Fontanelli, F; Forty, R; Francisco, O; Frank, M; Frei, C; Frosini, M; Furfaro, E; Gallas Torreira, A; Galli, D; Gandelman, M; Gandini, P; Gao, Y; Garofoli, J; Garosi, P; Garra Tico, J; Garrido, L; Gaspar, C; Gauld, R; Gersabeck, E; Gersabeck, M; Gershon, T; Ghez, Ph; Gibson, V; Giubega, L; Gligorov, V V; Göbel, C; Golubkov, D; Golutvin, A; Gomes, A; Gorbounov, P; Gordon, H; Grabalosa Gándara, M; Graciani Diaz, R; Granado Cardoso, L A; Graugés, E; Graziani, G; Grecu, A; Greening, E; Gregson, S; Griffith, P; Grünberg, O; Gui, B; Gushchin, E; Guz, Yu; Gys, T; Hadjivasiliou, C; Haefeli, G; Haen, C; Haines, S C; Hall, S; Hamilton, B; Hampson, T; Hansmann-Menzemer, S; Harnew, N; Harnew, S T; Harrison, J; Hartmann, T; He, J; Head, T; Heijne, V; Hennessy, K; Henrard, P; Hernando Morata, J A; van Herwijnen, E; Heß, M; Hicheur, A; Hicks, E; Hill, D; Hoballah, M; Hombach, C; Hulsbergen, W; Hunt, P; Huse, T; Hussain, N; Hutchcroft, D; Hynds, D; Iakovenko, V; Idzik, M; Ilten, P; Jacobsson, R; Jaeger, A; Jans, E; Jaton, P; Jawahery, A; Jing, F; John, M; Johnson, D; Jones, C R; Joram, C; Jost, B; Kaballo, M; Kandybei, S; Kanso, W; Karacson, M; Karbach, T M; Kenyon, I R; Ketel, T; Khanji, B; Kochebina, O; Komarov, I; Koopman, R F; Koppenburg, P; Korolev, M; Kozlinskiy, A; Kravchuk, L; Kreplin, K; Kreps, M; Krocker, G; Krokovny, P; Kruse, F; Kucharczyk, M; Kudryavtsev, V; Kurek, K; Kvaratskheliya, T; La Thi, V N; Lacarrere, D; Lafferty, G; Lai, A; Lambert, D; Lambert, R W; Lanciotti, E; Lanfranchi, G; Langenbruch, C; Latham, T; Lazzeroni, C; Le Gac, R; van Leerdam, J; Lees, J -P; Lefèvre, R; Leflat, A; Lefrançois, J; Leo, S; Leroy, O; Lesiak, T; Leverington, B; Li, Y; Li Gioi, L; Liles, M; Lindner, R; Linn, C; Liu, B; Liu, G; Lohn, S; Longstaff, I; Lopes, J H; Lopez-March, N; Lu, H; Lucchesi, D; Luisier, J; Luo, H; Lupton, O; Machefert, F; Machikhiliyan, I V; Maciuc, F; Maev, O; Malde, S; Manca, G; Mancinelli, G; Maratas, J; Marconi, U; Marino, P; Märki, R; Marks, J; Martellotti, G; Martens, A; Martín Sánchez, A; Martinelli, M; Martinez Santos, D; Martins Tostes, D; Martynov, A; Massafferri, A; Matev, R; Mathe, Z; Matteuzzi, C; Maurice, E; Mazurov, A; McCarthy, J; McNab, A; McNulty, R; McSkelly, B; Meadows, B; Meier, F; Meissner, M; Merk, M; Milanes, D A; Minard, M -N; Molina Rodriguez, J; Monteil, S; Moran, D; Morawski, P; Mordà, A; Morello, M J; Mountain, R; Mous, I; Muheim, F; Müller, K; Muresan, R; Muryn, B; Muster, B; Naik, P; Nakada, T; Nandakumar, R; Nasteva, I; Needham, M; Neubert, S; Neufeld, N; Nguyen, A D; Nguyen, T D; Nguyen-Mau, C; Nicol, M; Niess, V; Niet, R; Nikitin, N; Nikodem, T; Nomerotski, A; Novoselov, A; Oblakowska-Mucha, A; Obraztsov, V; Oggero, S; Ogilvy, S; Okhrimenko, O; Oldeman, R; Orlandea, M; Otalora Goicochea, J M; Owen, P; Oyanguren, A; Pal, B K; Palano, A; Palutan, M; Panman, J; Papanestis, A; Pappagallo, M; Parkes, C; Parkinson, C J; Passaleva, G; Patel, G D; Patel, M; Patrick, G N; Patrignani, C; Pavel-Nicorescu, C; Pazos Alvarez, A; Pearce, A; Pellegrino, A; Penso, G; Pepe Altarelli, M; Perazzini, S; Perez Trigo, E; Pérez-Calero Yzquierdo, A; Perret, P; Perrin-Terrin, M; Pescatore, L; Pesen, E; Pessina, G; Petridis, K; Petrolini, A; Phan, A; Picatoste Olloqui, E; Pietrzyk, B; Pilař, T; Pinci, D; Playfer, S; Plo Casasus, M; Polci, F; Polok, G; Poluektov, A; Polycarpo, E; Popov, A; Popov, D; Popovici, B; Potterat, C; Powell, A; Prisciandaro, J; Pritchard, A; Prouve, C; Pugatch, V; Puig Navarro, A; Punzi, G; Qian, W; Rachwal, B; Rademacker, J H; Rakotomiaramanana, B; Rangel, M S; Raniuk, I; Rauschmayr, N; Raven, G; Redford, S; Reichert, S; Reid, M M; dos Reis, A C; Ricciardi, S; Richards, A; Rinnert, K; Rives Molina, V; Roa Romero, D A; Robbe, P; Roberts, D A; Rodrigues, A B; Rodrigues, E; Rodriguez Perez, P; Roiser, S; Romanovsky, V; Romero Vidal, A; Rouvinet, J; Ruf, T; Ruffini, F; Ruiz, H; Ruiz Valls, P; Sabatino, G; Saborido Silva, J J; Sagidova, N; Sail, P; Saitta, B; Salustino Guimaraes, V; Sanmartin Sedes, B; Santacesaria, R; Santamarina Rios, C; Santovetti, E; Sapunov, M; Sarti, A; Satriano, C; Satta, A; Savrie, M; Savrina, D; Schiller, M; Schindler, H; Schlupp, M; Schmelling, M; Schmidt, B; Schneider, O; Schopper, A; Schune, M -H; Schwemmer, R; Sciascia, B; Sciubba, A; Seco, M; Semennikov, A; Senderowska, K; Sepp, I; Serra, N; Serrano, J; Seyfert, P; Shapkin, M; Shapoval, I; Shcheglov, Y; Shears, T; Shekhtman, L; Shevchenko, O; Shevchenko, V; Shires, A; Silva Coutinho, R; Sirendi, M; Skidmore, N; Skwarnicki, T; Smith, N A; Smith, E; Smith, E; Smith, J; Smith, M; Sokoloff, M D; Soler, F J P; Soomro, F; Souza, D; Souza De Paula, B; Spaan, B; Sparkes, A; Spradlin, P; Stagni, F; Stahl, S; Steinkamp, O; Stevenson, S; Stoica, S; Stone, S; Storaci, B; Straticiuc, M; Straumann, U; Subbiah, V K; Sun, L; Sutcliffe, W; Swientek, S; Syropoulos, V; Szczekowski, M; Szczypka, P; Szilard, D; Szumlak, T; T'Jampens, S; Teklishyn, M; Teodorescu, E; Teubert, F; Thomas, C; Thomas, E; van Tilburg, J; Tisserand, V; Tobin, M; Tolk, S; Tonelli, D; Topp-Joergensen, S; Torr, N; Tournefier, E; Tourneur, S; Tran, M T; Tresch, M; Tsaregorodtsev, A; Tsopelas, P; Tuning, N; Ubeda Garcia, M; Ukleja, A; Ustyuzhanin, A; Uwer, U; Vagnoni, V; Valenti, G; Vallier, A; Vazquez Gomez, R; Vazquez Regueiro, P; Vázquez Sierra, C; Vecchi, S; Velthuis, J J; Veltri, M; Veneziano, G; Vesterinen, M; Viaud, B; Vieira, D; Vilasis-Cardona, X; Vollhardt, A; Volyanskyy, D; Voong, D; Vorobyev, A; Vorobyev, V; Voß, C; Voss, H; Waldi, R; Wallace, C; Wallace, R; Wandernoth, S; Wang, J; Ward, D R; Watson, N K; Webber, A D; Websdale, D; Whitehead, M; Wicht, J; Wiechczynski, J; Wiedner, D; Wiggers, L; Wilkinson, G; Williams, M P; Williams, M; Wilson, F F; Wimberley, J; Wishahi, J; Wislicki, W; Witek, M; Wormser, G; Wotton, S A; Wright, S; Wu, S; Wyllie, K; Xie, Y; Xing, Z; Yang, Z; Yuan, X; Yushchenko, O; Zangoli, M; Zavertyaev, M; Zhang, F; Zhang, L; Zhang, W C; Zhang, Y; Zhelezov, A; Zhokhov, A; Zhong, L; Zvyagin, A

    2014-01-01

    The CP-violating charge asymmetry in $B^{\\pm}\\rightarrow \\phi K^{\\pm}$ decays is measured in a sample of $pp$ collisions at 7 TeV centre-of-mass energy, corresponding to an integrated luminosity of 1.0 fb$^{-1}$ collected by the LHCb experiment. The result is $\\mathcal{A}_{CP}(B^{\\pm}\\rightarrow \\phi K^{\\pm}) = \\rm 0.022\\pm 0.021 \\pm 0.009$, where the first uncertainty is statistical and the second systematic. In addition, a search for the $B^{\\pm}\\rightarrow \\phi \\pi^{\\pm}$ decay mode is performed, using the $B^{\\pm}\\rightarrow \\phi K^{\\pm}$ decay rate for normalization. An upper limit on the branching fraction $\\mathcal{B}(B^{\\pm}\\rightarrow \\phi \\pi^{\\pm})< 1.5\\times 10^{-7}$ is set at 90% confidence level.

  8. Search for $CP$ violation in $D^{\\pm}\\rightarrow K^0_S K^{\\pm}$ and $D^{\\pm}_{s}\\rightarrow K^0_S \\pi^{\\pm}$ decays

    CERN Document Server

    Aaij, R.; Adinolfi, M.; Affolder, A.; Ajaltouni, Z.; Akar, S.; Albrecht, J.; Alessio, F.; Alexander, M.; Ali, S.; Alkhazov, G.; Alvarez Cartelle, P.; Alves Jr, A.A.; Amato, S.; Amerio, S.; Amhis, Y.; An, L.; Anderlini, L.; Anderson, J.; Andreassen, R.; Andreotti, M.; Andrews, J.E.; Appleby, R.B.; Aquines Gutierrez, O.; Archilli, F.; Artamonov, A.; Artuso, M.; Aslanides, E.; Auriemma, G.; Baalouch, M.; Bachmann, S.; Back, J.J.; Badalov, A.; Balagura, V.; Baldini, W.; Barlow, R.J.; Barschel, C.; Barsuk, S.; Barter, W.; Batozskaya, V.; Battista, V.; Bay, A.; Beaucourt, L.; Beddow, J.; Bedeschi, F.; Bediaga, I.; Belogurov, S.; Belous, K.; Belyaev, I.; Ben-Haim, E.; Bencivenni, G.; Benson, S.; Benton, J.; Berezhnoy, A.; Bernet, R.; Bettler, M.O.; van Beuzekom, M.; Bien, A.; Bifani, S.; Bird, T.; Bizzeti, A.; Bjornstad, P.M.; Blake, T.; Blanc, F.; Blouw, J.; Blusk, S.; Bocci, V.; Bondar, A.; Bondar, N.; Bonivento, W.; Borghi, S.; Borgia, A.; Borsato, M.; Bowcock, T.J.V.; Bowen, E.; Bozzi, C.; Brambach, T.; van den Brand, J.; Bressieux, J.; Brett, D.; Britsch, M.; Britton, T.; Brodzicka, J.; Brook, N.H.; Brown, H.; Bursche, A.; Busetto, G.; Buytaert, J.; Cadeddu, S.; Calabrese, R.; Calvi, M.; Calvo Gomez, M.; Camboni, A.; Campana, P.; Campora Perez, D.; Carbone, A.; Carboni, G.; Cardinale, R.; Cardini, A.; Carranza-Mejia, H.; Carson, L.; Carvalho Akiba, K.; Casse, G.; Cassina, L.; Garcia, L.Castillo; Cattaneo, M.; Cauet, Ch.; Cenci, R.; Charles, M.; Charpentier, Ph.; Chen, S.; Cheung, S.F.; Chiapolini, N.; Chrzaszcz, M.; Ciba, K.; Cid Vidal, X.; Ciezarek, G.; Clarke, P.E.L.; Clemencic, M.; Cliff, H.V.; Closier, J.; Coco, V.; Cogan, J.; Cogneras, E.; Collins, P.; Comerma-Montells, A.; Contu, A.; Cook, A.; Coombes, M.; Coquereau, S.; Corti, G.; Corvo, M.; Counts, I.; Couturier, B.; Cowan, G.A.; Craik, D.C.; Cruz Torres, M.; Cunliffe, S.; Currie, R.; D'Ambrosio, C.; Dalseno, J.; David, P.; David, P.N.Y.; Davis, A.; De Bruyn, K.; De Capua, S.; De Cian, M.; de Miranda, J.M.; De Paula, L.; De Silva, W.; De Simone, P.; Decamp, D.; Deckenhoff, M.; Del Buono, L.; Deleage, N.; Derkach, D.; Deschamps, O.; Dettori, F.; Di Canto, A.; Dijkstra, H.; Donleavy, S.; Dordei, F.; Dorigo, M.; Dosil Suarez, A.; Dossett, D.; Dovbnya, A.; Dreimanis, K.; Dujany, G.; Dupertuis, F.; Durante, P.; Dzhelyadin, R.; Dziurda, A.; Dzyuba, A.; Easo, S.; Egede, U.; Egorychev, V.; Eidelman, S.; Eisenhardt, S.; Eitschberger, U.; Ekelhof, R.; Eklund, L.; El Rifai, I.; Elsasser, Ch.; Ely, S.; Esen, S.; Evans, T.; Falabella, A.; Farber, C.; Farinelli, C.; Farley, N.; Farry, S.; Fay, RF.; Ferguson, D.; Fernandez Albor, V.; Ferreira Rodrigues, F.; Ferro-Luzzi, M.; Filippov, S.; Fiore, M.; Fiorini, M.; Firlej, M.; Fitzpatrick, C.; Fiutowski, T.; Fontana, M.; Fontanelli, F.; Forty, R.; Francisco, O.; Frank, M.; Frei, C.; Frosini, M.; Fu, J.; Furfaro, E.; Gallas Torreira, A.; Galli, D.; Gallorini, S.; Gambetta, S.; Gandelman, M.; Gandini, P.; Gao, Y.; Garofoli, J.; Garra Tico, J.; Garrido, L.; Gaspar, C.; Gauld, R.; Gavardi, L.; Gavrilov, G.; Gersabeck, E.; Gersabeck, M.; Gershon, T.; Ghez, Ph.; Gianelle, A.; Giani', S.; Gibson, V.; Giubega, L.; Gligorov, V.V.; Gobel, C.; Golubkov, D.; Golutvin, A.; Gomes, A.; Gordon, H.; Gotti, C.; Grabalosa Gandara, M.; Graciani Diaz, R.; Granado Cardoso, L.A.; Grauges, E.; Graziani, G.; Grecu, A.; Greening, E.; Gregson, S.; Griffith, P.; Grillo, L.; Grunberg, O.; Gui, B.; Gushchin, E.; Guz, Yu.; Gys, T.; Hadjivasiliou, C.; Haefeli, G.; Haen, C.; Haines, S.C.; Hall, S.; Hamilton, B.; Hampson, T.; Han, X.; Hansmann-Menzemer, S.; Harnew, N.; Harnew, S.T.; Harrison, J.; Hartmann, T.; He, J.; Head, T.; Heijne, V.; Hennessy, K.; Henrard, P.; Henry, L.; Hernando Morata, J.A.; van Herwijnen, E.; Hess, M.; Hicheur, A.; Hill, D.; Hoballah, M.; Hombach, C.; Hulsbergen, W.; Hunt, P.; Hussain, N.; Hutchcroft, D.; Hynds, D.; Idzik, M.; Ilten, P.; Jacobsson, R.; Jaeger, A.; Jalocha, J.; Jans, E.; Jaton, P.; Jawahery, A.; Jing, F.; John, M.; Johnson, D.; Jones, C.R.; Joram, C.; Jost, B.; Jurik, N.; Kaballo, M.; Kandybei, S.; Kanso, W.; Karacson, M.; Karbach, T.M.; Karodia, S.; Kelsey, M.; Kenyon, I.R.; Ketel, T.; Khanji, B.; Khurewathanakul, C.; Klaver, S.; Kochebina, O.; Kolpin, M.; Komarov, I.; Koopman, R.F.; Koppenburg, P.; Korolev, M.; Kozlinskiy, A.; Kravchuk, L.; Kreplin, K.; Kreps, M.; Krocker, G.; Krokovny, P.; Kruse, F.; Kucewicz, W.; Kucharczyk, M.; Kudryavtsev, V.; Kurek, K.; Kvaratskheliya, T.; La Thi, V.N.; Lacarrere, D.; Lafferty, G.; Lai, A.; Lambert, D.; Lambert, R.W.; Lanciotti, E.; Lanfranchi, G.; Langenbruch, C.; Langhans, B.; Latham, T.; Lazzeroni, C.; Le Gac, R.; van Leerdam, J.; Lees, J.P.; Lefevre, R.; Leflat, A.; Lefrancois, J.; Leo, S.; Leroy, O.; Lesiak, T.; Leverington, B.; Li, Y.; Liles, M.; Lindner, R.; Linn, C.; Lionetto, F.; Liu, B.; Liu, G.; Lohn, S.; Longstaff, I.; Lopes, J.H.; Lopez-March, N.; Lowdon, P.; Lu, H.; Lucchesi, D.; Luo, H.; Lupato, A.; Luppi, E.; Lupton, O.; Machefert, F.; Machikhiliyan, I.V.; Maciuc, F.; Maev, O.; Malde, S.; Manca, G.; Mancinelli, G.; Maratas, J.; Marchand, J.F.; Marconi, U.; Benito, C.Marin; Marino, P.; Marki, R.; Marks, J.; Martellotti, G.; Martens, A.; Martin Sanchez, A.; Martinelli, M.; Martinez Santos, D.; Martinez Vidal, F.; Martins Tostes, D.; Massafferri, A.; Matev, R.; Mathe, Z.; Matteuzzi, C.; Mazurov, A.; McCann, M.; McCarthy, J.; McNab, A.; McNulty, R.; McSkelly, B.; Meadows, B.; Meier, F.; Meissner, M.; Merk, M.; Milanes, D.A.; Minard, M.N.; Moggi, N.; Molina Rodriguez, J.; Monteil, S.; Morandin, M.; Morawski, P.; Morda, A.; Morello, M.J.; Moron, J.; Morris, A.B.; Mountain, R.; Muheim, F.; Muller, K.; Muresan, R.; Mussini, M.; Muster, B.; Naik, P.; Nakada, T.; Nandakumar, R.; Nasteva, I.; Needham, M.; Neri, N.; Neubert, S.; Neufeld, N.; Neuner, M.; Nguyen, A.D.; Nguyen, T.D.; Nguyen-Mau, C.; Nicol, M.; Niess, V.; Niet, R.; Nikitin, N.; Nikodem, T.; Novoselov, A.; O'Hanlon, D.P.; Oblakowska-Mucha, A.; Obraztsov, V.; Oggero, S.; Ogilvy, S.; Okhrimenko, O.; Oldeman, R.; Onderwater, G.; Orlandea, M.; Otalora Goicochea, J.M.; Owen, P.; Oyanguren, A.; Pal, B.K.; Palano, A.; Palombo, F.; Palutan, M.; Panman, J.; Papanestis, A.; Pappagallo, M.; Parkes, C.; Parkinson, C.J.; Passaleva, G.; Patel, G.D.; Patel, M.; Patrignani, C.; Pazos Alvarez, A.; Pearce, A.; Pellegrino, A.; Pepe Altarelli, M.; Perazzini, S.; Perez Trigo, E.; Perret, P.; Perrin-Terrin, M.; Pescatore, L.; Pesen, E.; Petridis, K.; Petrolini, A.; Picatoste Olloqui, E.; Pietrzyk, B.; Pilar, T.; Pinci, D.; Pistone, A.; Playfer, S.; Plo Casasus, M.; Polci, F.; Poluektov, A.; Polycarpo, E.; Popov, A.; Popov, D.; Popovici, B.; Potterat, C.; Prisciandaro, J.; Pritchard, A.; Prouve, C.; Pugatch, V.; Puig Navarro, A.; Punzi, G.; Qian, W.; Rachwal, B.; Rademacker, J.H.; Rakotomiaramanana, B.; Rama, M.; Rangel, M.S.; Raniuk, I.; Rauschmayr, N.; Raven, G.; Reichert, S.; Reid, M.M.; dos Reis, A.C.; Ricciardi, S.; Richards, A.; Rihl, M.; Rinnert, K.; Rives Molina, V.; Roa Romero, D.A.; Robbe, P.; Rodrigues, A.B.; Rodrigues, E.; Rodriguez Perez, P.; Roiser, S.; Romanovsky, V.; Vidal, A.Romero; Rotondo, M.; Rouvinet, J.; Ruf, T.; Ruffini, F.; Ruiz, H.; Valls, P.Ruiz; Sabatino, G.; Saborido Silva, J.J.; Sagidova, N.; Sail, P.; Saitta, B.; Salustino Guimaraes, V.; Sanchez Mayordomo, C.; Sanmartin Sedes, B.; Santacesaria, R.; Santamarina Rios, C.; Santovetti, E.; Sapunov, M.; Sarti, A.; Satriano, C.; Satta, A.; Savrie, M.; Savrina, D.; Schiller, M.; Schindler, H.; Schlupp, M.; Schmelling, M.; Schmidt, B.; Schneider, O.; Schopper, A.; Schune, M.H.; Schwemmer, R.; Sciascia, B.; Sciubba, A.; Seco, M.; Semennikov, A.; Sepp, I.; Serra, N.; Serrano, J.; Sestini, L.; Seyfert, P.; Shapkin, M.; Shapoval, I.; Shcheglov, Y.; Shears, T.; Shekhtman, L.; Shevchenko, V.; Shires, A.; Coutinho, R.Silva; Simi, G.; Sirendi, M.; Skidmore, N.; Skwarnicki, T.; Smith, N.A.; Smith, E.; Smith, E.; Smith, J.; Smith, M.; Snoek, H.; Sokoloff, M.D.; Soler, F.J.P.; Soomro, F.; Souza, D.; Souza De Paula, B.; Spaan, B.; Sparkes, A.; Spradlin, P.; Stagni, F.; Stahl, M.; Stahl, S.; Steinkamp, O.; Stenyakin, O.; Stevenson, S.; Stoica, S.; Stone, S.; Storaci, B.; Stracka, S.; Straticiuc, M.; Straumann, U.; Stroili, R.; Subbiah, V.K.; Sun, L.; Sutcliffe, W.; Swientek, K.; Swientek, S.; Syropoulos, V.; Szczekowski, M.; Szczypka, P.; Szilard, D.; Szumlak, T.; T'Jampens, S.; Teklishyn, M.; Tellarini, G.; Teubert, F.; Thomas, C.; Thomas, E.; van Tilburg, J.; Tisserand, V.; Tobin, M.; Tolk, S.; Tomassetti, L.; Tonelli, D.; Topp-Joergensen, S.; Torr, N.; Tournefier, E.; Tourneur, S.; Tran, M.T.; Tresch, M.; Tsaregorodtsev, A.; Tsopelas, P.; Tuning, N.; Garcia, M.Ubeda; Ukleja, A.; Ustyuzhanin, A.; Uwer, U.; Vagnoni, V.; Valenti, G.; Vallier, A.; Vazquez Gomez, R.; Vazquez Regueiro, P.; Vazquez Sierra, C.; Vecchi, S.; Velthuis, J.J.; Veltri, M.; Veneziano, G.; Vesterinen, M.; Viaud, B.; Vieira, D.; Vieites Diaz, M.; Vilasis-Cardona, X.; Vollhardt, A.; Volyanskyy, D.; Voong, D.; Vorobyev, A.; Vorobyev, V.; Voss, C.; Voss, H.; de Vries, J.A.; Waldi, R.; Wallace, C.; Wallace, R.; Walsh, J.; Wandernoth, S.; Wang, J.; Ward, D.R.; Watson, N.K.; Websdale, D.; Whitehead, M.; Wicht, J.; Wiedner, D.; Wilkinson, G.; Williams, M.P.; Williams, M.; Wilson, F.F.; Wimberley, J.; Wishahi, J.; Wislicki, W.; Witek, M.; Wormser, G.; Wotton, S.A.; Wright, S.; Wu, S.; Wyllie, K.; Xie, Y.; Xing, Z.; Xu, Z.; Yang, Z.; Yuan, X.; Yushchenko, O.; Zangoli, M.; Zavertyaev, M.; Zhang, L.; Zhang, W.C.; Zhang, Y.; Zhelezov, A.; Zhokhov, A.; Zhong, L.; Zvyagin, A.

    2014-10-03

    A search for $CP$ violation in Cabibbo-suppressed $D^{\\pm}\\rightarrow K^0_S K^{\\pm}$ and $D^{\\pm}_{s}\\rightarrow K^0_S \\pi^{\\pm}$ decays is performed using $pp$ collision data, corresponding to an integrated luminosity of 3~fb$^{-1}$, recorded by the LHCb experiment. The individual $CP$-violating asymmetries are measured to be \\begin{eqnarray*} \\mathcal{A}_{CP}^{D^{\\pm}\\rightarrow K^0_S K^{\\pm}} & = & (+0.03 \\pm 0.17 \\pm 0.14) \\% \\\\ \\mathcal{A}_{CP}^{D^{\\pm}_s\\rightarrow K^0_S \\pi^{\\pm}} & = & (+0.38 \\pm 0.46 \\pm 0.17) \\%, \\end{eqnarray*} assuming that $CP$ violation in the Cabibbo-favoured decays is negligible. A combination of the measured asymmetries for the four decay modes $D^{\\pm}_{(s)}\\rightarrow K^0_S K^{\\pm}$ and $D^{\\pm}_{(s)}\\rightarrow K^0_S \\pi^{\\pm}$ gives the sum \\[ \\mathcal{A}_{CP}^{D^{\\pm}\\rightarrow K^0_S K^{\\pm}}+ \\mathcal{A}_{CP}^{D^{\\pm}_s\\rightarrow K^0_S \\pi^{\\pm}} = (+0.41 \\pm 0.49 \\pm 0.26) \\%. \\] In all cases, the first uncertainties are statistical and the second sys...

  9. Numerical analysis using state space method for vibration control of ...

    African Journals Online (AJOL)

    In passenger cars the vibrations developed at the ground are transmitted to the passengers through seats. Due to vibrations discomfort is experienced by the passengers. Dampers are being successfully utilized to reduce the vibrations in civil engineering structures. Few dampers are used in passenger cars as well.

  10. Homogeneous charge compression ignition compared with Otto-Atkinson in a passenger car size engine

    Energy Technology Data Exchange (ETDEWEB)

    Nagel, Andreas

    2000-07-01

    effective pressure between 2 and 4 bar and at higher speed. HCCI has an indicated efficiency up to 10 % higher than for Otto. 4 bar is the load limit for HCCI. When speed is rising, the combustion efficiency is decreasing but the indicated efficiency is increasing to maximum 49.5 % (3500 rpm). Pump losses are maintained low and the volumetric efficiency is held high at all speeds due to the warmer exhaust gases caused by a smaller engine. The valve area used by the Volvo TD 100 is maybe sufficient for Diesel combustion but not for HCCI when the pump losses could be decreased to one third with relatively larger valve area (Volvo 850). The emission levels are about the same no matter engine size, except for HC, which is about 50 percent lower in this work. This means that the combustion efficiency must be higher for the smaller engine. The already known fact that HCCI works best at part load still stands. The extra conclusion is that speed is no limitation in a passenger car size engine, at least below 4000 rpm.

  11. PASSENGER FLOWS PREDICTION IN MAJOR TRANSPORTATION HUBS

    Directory of Open Access Journals (Sweden)

    O. O. Ozerova

    2013-11-01

    Full Text Available Purpose. An effective organization of passenger traffic, due to the reliability prediction of traffic flow in passenger transport hubs. In order to determine the parameters of prospective passenger transport areas it is essential to analyze the impact of various factors and determine the most influential ones. Methodology. The article presents the method of paired linear correlation for a more influential factors on passengers in intercity and commuter and possible use in predicting the linear regression equations. Passenger transport vessel areas and branches of industry are interconnected and are in the ratio of passengers and production. Findings. It is found that the coefficient of correlation is in complex dependence on the duration of the period of retrospective analysis. Evaluation of reliability correlation coefficients and coefficients of predictive models led to the conclusion that the population gives the most accurate prediction of passenger flows, providing account of changes in Ukraine during the period of transformation. Originality. Equations of dependence on the impact of macroeconomic indicators were obtained and the evaluation of the reliability results was received. Practical value. The results of analysis and calculations will make short-term forecasting of traffic flow.

  12. Outdoor particulate matter (PM) and associated cardiovascular diseases in the Middle East.

    Science.gov (United States)

    Nasser, Zeina; Salameh, Pascale; Nasser, Wissam; Abou Abbas, Linda; Elias, Elias; Leveque, Alain

    2015-01-01

    Air pollution is a widespread environmental concern. Considerable epidemiological evidence indicates air pollution, particularly particulate matter (PM), as a major risk factor for cardiovascular diseases (CVD) in the developed countries. The main objective of our review is to assess the levels and sources of PM across the Middle East area and to search evidence for the relationship between PM exposure and CVD. An extensive review of the published literature pertaining to the subject (2000-2013) was conducted using PubMed, Medline and Google Scholar databases. We reveal that low utilization of public transport, ageing vehicle fleet and the increasing number of personal cars in the developing countries all contribute to the traffic congestion and aggravate the pollution problem. The annual average values of PM pollutants in the Middle East region are much higher than the World Health Organization 2006 guidelines (PM2.5 = 10 μg/m(3), PM10 = 20 μg/m(3)). We uncover evidence on the association between PM and CVD in 4 Middle East countries: Iran, Kingdom of Saudi Arabia, Qatar and the United Arab Emirates. The findings are in light of the international figures. Ambient PM pollution is considered a potential risk factor for platelet activation and atherosclerosis and has been found to be linked with an increased risk for mortality and hospital admissions due to CVD. This review highlights the importance of developing a strategy to improve air quality and reduce outdoor air pollution in the developing countries, particularly in the Middle East. Future studies should weigh the potential impact of PM on the overall burden of cardiac diseases. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

  13. US Advanced Freight and Passenger MAGLEV System

    Science.gov (United States)

    Morena, John J.; Danby, Gordon; Powell, James

    1996-01-01

    Japan and Germany will operate first generation Maglev passenger systems commercially shortly after 2000 A.D. The United States Maglev systems will require sophisticated freight and passenger carrying capability. The U.S. freight market is larger than passenger transport. A proposed advanced freight and passenger Maglev Project in Brevard County Florida is described. Present Maglev systems cost 30 million dollars or more per mile. Described is an advanced third generation Maglev system with technology improvements that will result in a cost of 10 million dollars per mile.

  14. U. K. surface passenger transport sector. Energy consumption and policy options for conservation

    Energy Technology Data Exchange (ETDEWEB)

    Maltby, D; Monteath, I G; Lawler, K A

    1978-12-01

    Forecasts of U.K. energy consumption in this sector for four future scenarios based on different economic growth rates, energy prices, and energy conservation policies, show that by the year 2000, private transport will probably account for 76-94% of total energy consumption in surface passenger transport. A 33% increase in the average miles-per-gallon fuel consumption through technological improvements in private vehicles, conversion of private vehicles to diesel oil, additional fuel taxation equivalent to 25 or 50% fuel price increase, a 10% reduction in average car engine size (encouraged by taxation), and changes in public transport technology offer energy savings of about 20, 5-10, 6.3 or 12.5, 2-4, and 2%, respectively. There is considerable uncertainty about the outcome of these options.

  15. Getting passengers out : evacuation behaviours

    NARCIS (Netherlands)

    Boer, L.C.

    2003-01-01

    When disaster strikes, mass transportation means mass evacuation. The issue is especially urgent if, despite precautions, a train comes to a stop in a tunnel and there is a fire. Adequate behaviour of passengers is a major success factor of an evacuation. Passengers should replace their original

  16. 75 FR 64268 - New Pneumatic Off-the-Road Tires From the People's Republic of China: Preliminary Results of...

    Science.gov (United States)

    2010-10-19

    ..., manufactured and offered for sale primarily for on-highway or on-road use, including passenger cars, race cars... primarily for service on passenger cars; LT--Identifies a tire intended primarily for service on light...

  17. Passenger and freight transport perspectives for 2035. Background report for transport policy discussion; Henkiloe- ja tavaraliikenteen kehityskuva 2035. Taustaraportti liikennepoliittiseen keskusteluun

    Energy Technology Data Exchange (ETDEWEB)

    Luukkonen, T.; Maekelae, T.; Pollanen, M.; Kalenoja, H.; Mantynen, J.; Rantala, J.

    2012-07-01

    This study aims to image the perspectives for future transport on the basis of existing estimates and expert views. The results of this study offer a justified perception of how Finnish passenger and freight transport will develop up to year 2035. The study also includes six 'what if' analysis which address how six individual and important changes could affect transports. The development of population and the economy are key factors in the operating environment of passenger and freight transport. To a large extent, they determine the development of the demand for passenger and freight transport. Earlier population forecasts have underestimated population growth in Finland. Uncertainty also surrounds regional demographic development, which is connected both to the development of community structure and land use, and to time use and consumption habits associated with travel preferences. The development of the economy, which also involves considerable uncertainty, is connected to population through developments in employment and income levels, among others, while growing workplace areas also attract people and increase commuting, for example. Changing travel habits and ageing of the population influence the overall demand for passenger transport. Efforts are being made to promote walking, cycling and the use of public transport. In the future these means of transport will be supported by factors such as increased awareness of the environment and health, and concentration of population in cities. While the aim is to constrain the growth of passenger car traffic, rising income levels and travel distances in the operating environment will serve to increase passenger car traffic and the demand for long-distance train, flight and bus traffic. The supply of different transport methods and the costs of their use will, for their part, affect transport mode distribution. The development of the economy and various sectors will determine the demand for freight

  18. Trends of NO-, NO 2-, and NH 3-emissions from gasoline-fueled Euro-3- to Euro-4-passenger cars

    Science.gov (United States)

    Heeb, Norbert V.; Saxer, Christian J.; Forss, Anna-Maria; Brühlmann, Stefan

    Vehicular emissions of reactive nitrogen compounds (RNCs) such as nitric oxide (NO), nitrogen dioxide (NO 2), and ammonia (NH 3) have a substantial impact on urban air quality. NO and NO 2 support the photochemical formation of ozone, and NH 3 is involved in the atmospheric formation of secondary aerosols. Vehicular NO is mainly formed during combustion, whereas NO 2 and NH 3 are both secondary pollutants of the catalytic converter systems. Herein we report on tail-pipe RNC emissions of gasoline-fueled Euro-3- and Euro-4-passenger cars at transient driving from 0 to 150 km h -1. Two sets of 10 in-use vehicles with comparable engine size and mileage were studied with time-resolved chemical ionization-mass spectrometry (CI-MS). Each vehicle was tested in 7 different driving cycles including the legislative European (EDC) and the US FTP-75 driving cycles. Mean emission factors (EFs) for different traffic situations are reported and effects of cold start, velocity, acceleration, and deceleration are discussed. Furthermore, critical operating conditions supporting the de novo formation of NH 3 have been identified. In the EDC, mean NO- and NH 3-EFs of 57±26 and 16±12 mg km -1 were obtained for Euro-3-vehicles; those of the Euro-4-technology were lower by about 25% and 33% at the levels of 43±46 and 10±7 mg km -1, respectively. NO 2 emissions of the investigated three-way catalyst (TWC) vehicles accounted for exhaust. Velocity and acceleration had pronounced effects on the RNC emission characteristics. Mean velocity-dependent EFs for NO and NH 3 varied by about one order of magnitude from 10 to 74 and 15 to 161 mg km -1 for Euro-3-vehicles and from 12 to 44 and 7 to 144 mg km -1 for the Euro-4 fleet. We conclude that the investigated Euro-3- and Euro-4-vehicles are mainly operated under slightly reducing conditions, where the NH 3 emissions dominate over those of the NO. Under these conditions, both vehicle fleets on an average fulfilled the valid Euro-3 and Euro-4

  19. Commuter exposure to PM2.5, BC, and UFP in six common transport microenvironments in Sacramento, California

    Science.gov (United States)

    Ham, Walter; Vijayan, Abhilash; Schulte, Nico; Herner, Jorn D.

    2017-10-01

    This study was designed to estimate and compare the air pollution exposures experienced by commuters in six common transportation modes utilized by California residents, and to evaluate the impact of practical exposure mitigation strategies in reducing commute exposures. We measured concentrations of fine particle matter (PM2.5), black carbon (BC), and ultrafine particles (UFP) for 161 commutes between April 2014 and November 2015 in Sacramento, CA. We collected measurements for six modes including single occupancy vehicles, high occupancy vehicles (multiple occupants), buses, light rail, train, and bicycling. The largest average concentrations for most pollutants were measured during train commutes and the lowest average concentrations were observed during light-rail commutes. Mitigation options were explored for personal vehicles, bicycling, and train commute modes. We found that ventilation settings of personal vehicles can reduce in-vehicle PM2.5, BC, and UFP concentrations by up to 75%. Similarly, bicycle route choice can reduce exposures by 15-75% with the lowest concentrations observed during commutes on dedicated bicycle paths away from traffic sources. Train commuters experienced UFP concentrations an order of magnitude greater when the locomotive engine was pulling the rail cars versus pushing the rail cars. We found that UFP concentrations during bus, bicycling, and train commutes were 1.6-5.3 times greater than personal vehicle commutes, while light rail commutes had 30% lower UFP concentrations than personal vehicle commutes. The largest exposure per mile occurred during bicycle commutes with PM2.5, BC, and UFP exposures of 1.312 μg/mile, 0.097 μg/mile, and 3.0 × 109 particles/mile, respectively. Train commutes experienced the largest exposure per mile of all of the combustion-derived transportation commute modes. BC accounted for 5-20% of total PM mass across all commute modes with an average fraction of ∼7% of PM2.5.

  20. Measurement of CP violation in the phase space of $B^{\\pm} \\rightarrow K^{+} K^{-} \\pi^{\\pm}$ and $B^{\\pm} \\rightarrow \\pi^{+} \\pi^{-} \\pi^{\\pm}$ decays

    CERN Document Server

    Aaij, Roel; Adinolfi, Marco; Adrover, Cosme; Affolder, Anthony; Ajaltouni, Ziad; Albrecht, Johannes; Alessio, Federico; Alexander, Michael; Ali, Suvayu; Alkhazov, Georgy; Alvarez Cartelle, Paula; Alves Jr, Antonio; Amato, Sandra; Amerio, Silvia; Amhis, Yasmine; Anderlini, Lucio; Anderson, Jonathan; Andreassen, Rolf; Andrews, Jason; Appleby, Robert; Aquines Gutierrez, Osvaldo; Archilli, Flavio; Artamonov, Alexander; Artuso, Marina; Aslanides, Elie; Auriemma, Giulio; Baalouch, Marouen; Bachmann, Sebastian; Back, John; Badalov, Alexey; Baesso, Clarissa; Balagura, Vladislav; Baldini, Wander; Barlow, Roger; Barschel, Colin; Barsuk, Sergey; Barter, William; Bauer, Thomas; Bay, Aurelio; Beddow, John; Bedeschi, Franco; Bediaga, Ignacio; Belogurov, Sergey; Belous, Konstantin; Belyaev, Ivan; Ben-Haim, Eli; Bencivenni, Giovanni; Benson, Sean; Benton, Jack; Berezhnoy, Alexander; Bernet, Roland; Bettler, Mar-Olivier; van Beuzekom, Martinus; Bien, Alexander; Bifani, Simone; Bird, Thomas; Bizzeti, Andrea; Bjørnstad, Pål Marius; Blake, Thomas; Blanc, Frédéric; Blouw, Johan; Blusk, Steven; Bocci, Valerio; Bondar, Alexander; Bondar, Nikolay; Bonivento, Walter; Borghi, Silvia; Borgia, Alessandra; Bowcock, Themistocles; Bowen, Espen Eie; Bozzi, Concezio; Brambach, Tobias; van den Brand, Johannes; Bressieux, Joël; Brett, David; Britsch, Markward; Britton, Thomas; Brook, Nicholas; Brown, Henry; Bursche, Albert; Busetto, Giovanni; Buytaert, Jan; Cadeddu, Sandro; Callot, Olivier; Calvi, Marta; Calvo Gomez, Miriam; Camboni, Alessandro; Campana, Pierluigi; Campora Perez, Daniel; Carbone, Angelo; Carboni, Giovanni; Cardinale, Roberta; Cardini, Alessandro; Carranza-Mejia, Hector; Carson, Laurence; Carvalho Akiba, Kazuyoshi; Casse, Gianluigi; Castillo Garcia, Lucia; Cattaneo, Marco; Cauet, Christophe; Cenci, Riccardo; Charles, Matthew; Charpentier, Philippe; Cheung, Shu-Faye; Chiapolini, Nicola; Chrzaszcz, Marcin; Ciba, Krzystof; Cid Vidal, Xabier; Ciezarek, Gregory; Clarke, Peter; Clemencic, Marco; Cliff, Harry; Closier, Joel; Coca, Cornelia; Coco, Victor; Cogan, Julien; Cogneras, Eric; Collins, Paula; Comerma-Montells, Albert; Contu, Andrea; Cook, Andrew; Coombes, Matthew; Coquereau, Samuel; Corti, Gloria; Couturier, Benjamin; Cowan, Greig; Craik, Daniel Charles; Cruz Torres, Melissa Maria; Cunliffe, Samuel; Currie, Robert; D'Ambrosio, Carmelo; David, Pascal; David, Pieter; Davis, Adam; De Bonis, Isabelle; De Bruyn, Kristof; De Capua, Stefano; De Cian, Michel; De Miranda, Jussara; De Paula, Leandro; De Silva, Weeraddana; De Simone, Patrizia; Decamp, Daniel; Deckenhoff, Mirko; Del Buono, Luigi; Déléage, Nicolas; Derkach, Denis; Deschamps, Olivier; Dettori, Francesco; Di Canto, Angelo; Dijkstra, Hans; Dogaru, Marius; Donleavy, Stephanie; Dordei, Francesca; Dosil Suárez, Alvaro; Dossett, David; Dovbnya, Anatoliy; Dupertuis, Frederic; Durante, Paolo; Dzhelyadin, Rustem; Dziurda, Agnieszka; Dzyuba, Alexey; Easo, Sajan; Egede, Ulrik; Egorychev, Victor; Eidelman, Semen; van Eijk, Daan; Eisenhardt, Stephan; Eitschberger, Ulrich; Ekelhof, Robert; Eklund, Lars; El Rifai, Ibrahim; Elsasser, Christian; Falabella, Antonio; Färber, Christian; Farinelli, Chiara; Farry, Stephen; Ferguson, Dianne; Fernandez Albor, Victor; Ferreira Rodrigues, Fernando; Ferro-Luzzi, Massimiliano; Filippov, Sergey; Fiore, Marco; Fitzpatrick, Conor; Fontana, Marianna; Fontanelli, Flavio; Forty, Roger; Francisco, Oscar; Frank, Markus; Frei, Christoph; Frosini, Maddalena; Furfaro, Emiliano; Gallas Torreira, Abraham; Galli, Domenico; Gandelman, Miriam; Gandini, Paolo; Gao, Yuanning; Garofoli, Justin; Garosi, Paola; Garra Tico, Jordi; Garrido, Lluis; Gaspar, Clara; Gauld, Rhorry; Gersabeck, Evelina; Gersabeck, Marco; Gershon, Timothy; Ghez, Philippe; Gibson, Valerie; Giubega, Lavinia-Helena; Gligorov, V.V.; Göbel, Carla; Golubkov, Dmitry; Golutvin, Andrey; Gomes, Alvaro; Gorbounov, Petr; Gordon, Hamish; Grabalosa Gándara, Marc; Graciani Diaz, Ricardo; Granado Cardoso, Luis Alberto; Graugés, Eugeni; Graziani, Giacomo; Grecu, Alexandru; Greening, Edward; Gregson, Sam; Griffith, Peter; Grillo, Lucia; Grünberg, Oliver; Gui, Bin; Gushchin, Evgeny; Guz, Yury; Gys, Thierry; Hadjivasiliou, Christos; Haefeli, Guido; Haen, Christophe; Haines, Susan; Hall, Samuel; Hamilton, Brian; Hampson, Thomas; Hansmann-Menzemer, Stephanie; Harnew, Neville; Harnew, Samuel; Harrison, Jonathan; Hartmann, Thomas; He, Jibo; Head, Timothy; Heijne, Veerle; Hennessy, Karol; Henrard, Pierre; Hernando Morata, Jose Angel; van Herwijnen, Eric; Heß, Miriam; Hicheur, Adlène; Hicks, Emma; Hill, Donal; Hoballah, Mostafa; Hombach, Christoph; Hulsbergen, Wouter; Hunt, Philip; Huse, Torkjell; Hussain, Nazim; Hutchcroft, David; Hynds, Daniel; Iakovenko, Viktor; Idzik, Marek; Ilten, Philip; Jacobsson, Richard; Jaeger, Andreas; Jans, Eddy; Jaton, Pierre; Jawahery, Abolhassan; Jing, Fanfan; John, Malcolm; Johnson, Daniel; Jones, Christopher; Joram, Christian; Jost, Beat; Kaballo, Michael; Kandybei, Sergii; Kanso, Wallaa; Karacson, Matthias; Karbach, Moritz; Kenyon, Ian; Ketel, Tjeerd; Khanji, Basem; Kochebina, Olga; Komarov, Ilya; Koopman, Rose; Koppenburg, Patrick; Korolev, Mikhail; Kozlinskiy, Alexandr; Kravchuk, Leonid; Kreplin, Katharina; Kreps, Michal; Krocker, Georg; Krokovny, Pavel; Kruse, Florian; Kucharczyk, Marcin; Kudryavtsev, Vasily; Kurek, Krzysztof; Kvaratskheliya, Tengiz; La Thi, Viet Nga; Lacarrere, Daniel; Lafferty, George; Lai, Adriano; Lambert, Dean; Lambert, Robert W; Lanciotti, Elisa; Lanfranchi, Gaia; Langenbruch, Christoph; Latham, Thomas; Lazzeroni, Cristina; Le Gac, Renaud; van Leerdam, Jeroen; Lees, Jean-Pierre; Lefèvre, Regis; Leflat, Alexander; Lefrançois, Jacques; Leo, Sabato; Leroy, Olivier; Lesiak, Tadeusz; Leverington, Blake; Li, Yiming; Li Gioi, Luigi; Liles, Myfanwy; Lindner, Rolf; Linn, Christian; Liu, Bo; Liu, Guoming; Lohn, Stefan; Longstaff, Ian; Lopes, Jose; Lopez-March, Neus; Lu, Haiting; Lucchesi, Donatella; Luisier, Johan; Luo, Haofei; Lupton, Oliver; Machefert, Frederic; Machikhiliyan, Irina V; Maciuc, Florin; Maev, Oleg; Malde, Sneha; Manca, Giulia; Mancinelli, Giampiero; Maratas, Jan; Marconi, Umberto; Marino, Pietro; Märki, Raphael; Marks, Jörg; Martellotti, Giuseppe; Martens, Aurelien; Martín Sánchez, Alexandra; Martinelli, Maurizio; Martinez Santos, Diego; Martins Tostes, Danielle; Martynov, Aleksandr; Massafferri, André; Matev, Rosen; Mathe, Zoltan; Matteuzzi, Clara; Maurice, Emilie; Mazurov, Alexander; McCarthy, James; McNab, Andrew; McNulty, Ronan; McSkelly, Ben; Meadows, Brian; Meier, Frank; Meissner, Marco; Merk, Marcel; Milanes, Diego Alejandro; Minard, Marie-Noelle; Molina Rodriguez, Josue; Monteil, Stephane; Moran, Dermot; Morawski, Piotr; Mordà, Alessandro; Morello, Michael Joseph; Mountain, Raymond; Mous, Ivan; Muheim, Franz; Müller, Katharina; Muresan, Raluca; Muryn, Bogdan; Muster, Bastien; Naik, Paras; Nakada, Tatsuya; Nandakumar, Raja; Nasteva, Irina; Needham, Matthew; Neubert, Sebastian; Neufeld, Niko; Nguyen, Anh Duc; Nguyen, Thi-Dung; Nguyen-Mau, Chung; Nicol, Michelle; Niess, Valentin; Niet, Ramon; Nikitin, Nikolay; Nikodem, Thomas; Nomerotski, Andrey; Novoselov, Alexey; Oblakowska-Mucha, Agnieszka; Obraztsov, Vladimir; Oggero, Serena; Ogilvy, Stephen; Okhrimenko, Oleksandr; Oldeman, Rudolf; Orlandea, Marius; Otalora Goicochea, Juan Martin; Owen, Patrick; Oyanguren, Maria Arantza; Pal, Bilas Kanti; Palano, Antimo; Palutan, Matteo; Panman, Jacob; Papanestis, Antonios; Pappagallo, Marco; Parkes, Christopher; Parkinson, Christopher John; Passaleva, Giovanni; Patel, Girish; Patel, Mitesh; Patrick, Glenn; Patrignani, Claudia; Pavel-Nicorescu, Carmen; Pazos Alvarez, Antonio; Pearce, Alex; Pellegrino, Antonio; Penso, Gianni; Pepe Altarelli, Monica; Perazzini, Stefano; Perez Trigo, Eliseo; Pérez-Calero Yzquierdo, Antonio; Perret, Pascal; Perrin-Terrin, Mathieu; Pescatore, Luca; Pesen, Erhan; Pessina, Gianluigi; Petridis, Konstantin; Petrolini, Alessandro; Phan, Anna; Picatoste Olloqui, Eduardo; Pietrzyk, Boleslaw; Pilař, Tomas; Pinci, Davide; Playfer, Stephen; Plo Casasus, Maximo; Polci, Francesco; Polok, Grzegorz; Poluektov, Anton; Polycarpo, Erica; Popov, Alexander; Popov, Dmitry; Popovici, Bogdan; Potterat, Cédric; Powell, Andrew; Prisciandaro, Jessica; Pritchard, Adrian; Prouve, Claire; Pugatch, Valery; Puig Navarro, Albert; Punzi, Giovanni; Qian, Wenbin; Rachwal, Bartolomiej; Rademacker, Jonas; Rakotomiaramanana, Barinjaka; Rangel, Murilo; Raniuk, Iurii; Rauschmayr, Nathalie; Raven, Gerhard; Redford, Sophie; Reichert, Stefanie; Reid, Matthew; dos Reis, Alberto; Ricciardi, Stefania; Richards, Alexander; Rinnert, Kurt; Rives Molina, Vincente; Roa Romero, Diego; Robbe, Patrick; Roberts, Douglas; Rodrigues, Ana Barbara; Rodrigues, Eduardo; Rodriguez Perez, Pablo; Roiser, Stefan; Romanovsky, Vladimir; Romero Vidal, Antonio; Rotondo, Marcello; Rouvinet, Julien; Ruf, Thomas; Ruffini, Fabrizio; Ruiz, Hugo; Ruiz Valls, Pablo; Sabatino, Giovanni; Saborido Silva, Juan Jose; Sagidova, Naylya; Sail, Paul; Saitta, Biagio; Salustino Guimaraes, Valdir; Sanmartin Sedes, Brais; Santacesaria, Roberta; Santamarina Rios, Cibran; Santovetti, Emanuele; Sapunov, Matvey; Sarti, Alessio; Satriano, Celestina; Satta, Alessia; Savrie, Mauro; Savrina, Darya; Schiller, Manuel; Schindler, Heinrich; Schlupp, Maximilian; Schmelling, Michael; Schmidt, Burkhard; Schneider, Olivier; Schopper, Andreas; Schune, Marie Helene; Schwemmer, Rainer; Sciascia, Barbara; Sciubba, Adalberto; Seco, Marcos; Semennikov, Alexander; Senderowska, Katarzyna; Sepp, Indrek; Serra, Nicola; Serrano, Justine; Seyfert, Paul; Shapkin, Mikhail; Shapoval, Illya; Shcheglov, Yury; Shears, Tara; Shekhtman, Lev; Shevchenko, Oksana; Shevchenko, Vladimir; Shires, Alexander; Silva Coutinho, Rafael; Sirendi, Marek; Skidmore, Nicola; Skwarnicki, Tomasz; Smith, Anthony; Smith, Edmund; Smith, Eluned; Smith, Jackson; Smith, Mark; Sokoloff, Michael; Soler, Paul; Soomro, Fatima; Souza, Daniel; Souza De Paula, Bruno; Spaan, Bernhard; Sparkes, Ailsa; Spradlin, Patrick; Stagni, Federico; Stahl, Sascha; Steinkamp, Olaf; Stevenson, Scott; Stoica, Sabin; Stone, Sheldon; Storaci, Barbara; Straticiuc, Mihai; Straumann, Ulrich; Subbiah, Vijay Kartik; Sun, Liang; Sutcliffe, William; Swientek, Stefan; Syropoulos, Vasileios; Szczekowski, Marek; Szczypka, Paul; Szilard, Daniela; Szumlak, Tomasz; T'Jampens, Stephane; Teklishyn, Maksym; Teodorescu, Eliza; Teubert, Frederic; Thomas, Christopher; Thomas, Eric; van Tilburg, Jeroen; Tisserand, Vincent; Tobin, Mark; Tolk, Siim; Tonelli, Diego; Topp-Joergensen, Stig; Torr, Nicholas; Tournefier, Edwige; Tourneur, Stephane; Tran, Minh Tâm; Tresch, Marco; Tsaregorodtsev, Andrei; Tsopelas, Panagiotis; Tuning, Niels; Ubeda Garcia, Mario; Ukleja, Artur; Ustyuzhanin, Andrey; Uwer, Ulrich; Vagnoni, Vincenzo; Valenti, Giovanni; Vallier, Alexis; Vazquez Gomez, Ricardo; Vazquez Regueiro, Pablo; Vázquez Sierra, Carlos; Vecchi, Stefania; Velthuis, Jaap; Veltri, Michele; Veneziano, Giovanni; Vesterinen, Mika; Viaud, Benoit; Vieira, Daniel; Vilasis-Cardona, Xavier; Vollhardt, Achim; Volyanskyy, Dmytro; Voong, David; Vorobyev, Alexey; Vorobyev, Vitaly; Voß, Christian; Voss, Helge; Waldi, Roland; Wallace, Charlotte; Wallace, Ronan; Wandernoth, Sebastian; Wang, Jianchun; Ward, David; Watson, Nigel; Webber, Adam Dane; Websdale, David; Whitehead, Mark; Wicht, Jean; Wiechczynski, Jaroslaw; Wiedner, Dirk; Wiggers, Leo; Wilkinson, Guy; Williams, Matthew; Williams, Mike; Wilson, Fergus; Wimberley, Jack; Wishahi, Julian; Wislicki, Wojciech; Witek, Mariusz; Wormser, Guy; Wotton, Stephen; Wright, Simon; Wu, Suzhi; Wyllie, Kenneth; Xie, Yuehong; Xing, Zhou; Yang, Zhenwei; Yuan, Xuhao; Yushchenko, Oleg; Zangoli, Maria; Zavertyaev, Mikhail; Zhang, Feng; Zhang, Liming; Zhang, Wen Chao; Zhang, Yanxi; Zhelezov, Alexey; Zhokhov, Anatoly; Zhong, Liang; Zvyagin, Alexander

    2014-01-01

    The charmless decays $B^{\\pm} \\rightarrow K^{+}K^{-}\\pi^{\\pm}$ and $B^{\\pm} \\rightarrow \\pi^{+}\\pi^{-}\\pi^{\\pm}$ are reconstructed in a data set, corresponding to an integrated luminosity of 1.0 fb$^{-1}$ of pp collisions at a center-of-mass energy of 7 TeV, collected by LHCb in 2011. The inclusive charge asymmetries of these modes are measured to be $A_{CP}(B^{\\pm} \\rightarrow K^{+}K^{-}\\pi^{\\pm}) =-0.141 \\pm 0.040 (stat) \\pm 0.018 (syst) \\pm 0.007 (J/\\psi K^{\\pm})$ and $A_{CP}(B^{\\pm} \\rightarrow \\pi^{+}\\pi^{-}\\pi^{\\pm}) = 0.117 \\pm 0.021 (stat) \\pm 0.009 (syst) \\pm 0.007 (J/\\psi K^{\\pm})$, where the third uncertainty is due to the CP asymmetry of the $B^{\\pm} \\rightarrow J/\\psi K^{\\pm}$ reference mode. In addition to the inclusive CP asymmetries, larger asymmetries are observed in localized regions of phase space.

  1. Optimal boarding method for airline passengers

    Energy Technology Data Exchange (ETDEWEB)

    Steffen, Jason H.; /Fermilab

    2008-02-01

    Using a Markov Chain Monte Carlo optimization algorithm and a computer simulation, I find the passenger ordering which minimizes the time required to board the passengers onto an airplane. The model that I employ assumes that the time that a passenger requires to load his or her luggage is the dominant contribution to the time needed to completely fill the aircraft. The optimal boarding strategy may reduce the time required to board and airplane by over a factor of four and possibly more depending upon the dimensions of the aircraft. I explore some features of the optimal boarding method and discuss practical modifications to the optimal. Finally, I mention some of the benefits that could come from implementing an improved passenger boarding scheme.

  2. Telemedical advice to long-distance passenger ferries

    DEFF Research Database (Denmark)

    Jensen, Olaf C; Bo Bøggild, Niels; Kristensen, Søren

    2005-01-01

    BACKGROUND: Radio medical (RM) advice for seafarers and traveling passengers is important and can be crucial for the optimal medical treatment on board ships. The aim of this study was to analyze the data from consultations with passenger ferries to identify areas for possible improvements. METHODS......: Data from the journals for 1 year from Radio Medical Denmark consultations with the medical officers on passenger ferries were analyzed retrospectively. RESULTS: Two hundred fourteen RM records, 73% pertaining to passengers and 27% for crew members, were analyzed. Passenger patients were generally...... complaints, and more than half of these involved severe or considerable pain. Only acetaminophen (paracetamol) and opioids were in the ferry medicine chest. At least 77 patients would have benefited from use of nonsteroidal anti-inflammatory drugs. CONCLUSIONS: The paramedical assistance and the medicine...

  3. Level of service at airport passenger terminals

    Directory of Open Access Journals (Sweden)

    Tasić Tamara D.

    2016-01-01

    Full Text Available Airport terminals are designed by level of service standards which are regulated by International Air Transport Association (IATA. Level of service offered to passengers, regarding to the primary processes, is not necessarily equivalent to the level of service perceived by them. The fact that passengers spending longer times in terminals makes the secondary processes more important in passenger experience. Aiming to improving airport attractiveness, and business success, passenger perception is approached by paying close attention. This paper discusses the two aspects of level of service. Concept of level of service used in air traffic industry with purpose of designing and planning of passenger terminal is derived from the Highway Capacity Manual. Subject of the paper regards last changes which have been introduced during 2014. Second part of the paper explains the needs of examining and analyzing passenger perception from the management point of view, and gives overview of methods which are conducted during researches. Similarities and differences are shown among measurements of level of service and perceived level of service, including the importance of these aspects mutual complementing.

  4. FreedomCAR Advanced Traction Drive Motor Development Phase I

    Energy Technology Data Exchange (ETDEWEB)

    Ley, Josh (UQM Technologies, Inc.); Lutz, Jon (UQM Technologies, Inc.)

    2006-09-01

    The overall objective of this program is to design and develop an advanced traction motor that will meet the FreedomCAR and Vehicle Technologies (FCVT) 2010 goals and the traction motor technical targets. The motor specifications are given in Section 1.3. Other goals of the program include providing a cost study to ensure the motor can be developed within the cost targets needed for the automotive industry. The program has focused on using materials that are both high performance and low costs such that the performance can be met and cost targets are achieved. In addition, the motor technologies and machine design features must be compatible with high volume manufacturing and able to provide high reliability, efficiency, and ruggedness while simultaneously reducing weight and volume. Weight and volume reduction will become a major factor in reducing cost, material cost being the most significant part of manufacturing cost at high volume. Many motor technology categories have been considered in the past and present for traction drive applications, including: brushed direct current (DC), PM (PM) brushless dc (BLDC), alternating current (AC) induction, switched reluctance and synchronous reluctance machines. Of these machine technologies, PM BLDC has consistently demonstrated an advantage in terms of power density and efficiency. As rare earth magnet cost has declined, total cost may also be reduced over the other technologies. Of the many different configurations of PM BLDC machines, those which incorporate power production utilizing both magnetic torque as well as reluctance torque appear to have the most promise for traction applications. There are many different PM BLDC machine configurations which employ both of these torque producing mechanisms; however, most would fall into one of two categories--some use weaker magnets and rely more heavily on reluctance torque (reluctance-dominant PM machines), others use strong PMs and supplement with reluctance torque

  5. The Effect of Passengers on Teen Driver Behavior

    Science.gov (United States)

    2012-04-01

    A number of studies have shown that passengers substantially increase the risk of crashes for young, novice drivers. This increased risk may result from distractions that young passengers create for drivers. Alternatively, the presence of passengers ...

  6. Assessment of environmental measures in the Dutch Tax Plan 2008

    International Nuclear Information System (INIS)

    2007-09-01

    The environmental measures that were included in the Dutch Tax plan 2008 have been evaluated for their CO2 effects. In addition, the effects on NOx and PM10 emissions have been quantified. They are the following measures: (1) Environmental differentiation of cars Clean and efficient; (2) Adjustment of addition for private use of company cars; (3) Additional financial burden environment unfriendly fuels/energy; (4) Introduction of air passenger tax (350 million euro) (5) Shift from BPM1 to MRB2; (6) Balancing energy tax for sustainably generated electricity for small consumers; (7) Introduction of packaging tax; (8) Adjustment of the tariff of waste for shredder. The effects of measures 2,7 and 8 have not been assessed by MNP (Netherlands Environmental Assessment Agency). [mk] [nl

  7. Measurement of $C\\!P$ violation in the phase space of $B^{\\pm} \\to K^{\\pm} \\pi^{+} \\pi^{-}$ and $B^{\\pm} \\to K^{\\pm} K^{+} K^{-}$ decays

    CERN Document Server

    INSPIRE-00258707; Adeva, B; Adinolfi, M; Adrover, C; Affolder, A; Ajaltouni, Z; Albrecht, J; Alessio, F; Alexander, M; Ali, S; Alkhazov, G; Alvarez Cartelle, P; Alves Jr, A A; Amato, S; Amerio, S; Amhis, Y; Anderlini, L; Anderson, J; Andreassen, R; Andrews, J E; Appleby, R B; Aquines Gutierrez, O; Archilli, F; Artamonov, A; Artuso, M; Aslanides, E; Auriemma, G; Baalouch, M; Bachmann, S; Back, J J; Baesso, C; Balagura, V; Baldini, W; Barlow, R J; Barschel, C; Barsuk, S; Barter, W; Bauer, Th; Bay, A; Beddow, J; Bedeschi, F; Bediaga, I; Belogurov, S; Belous, K; Belyaev, I; Ben-Haim, E; Bencivenni, G; Benson, S; Benton, J; Berezhnoy, A; Bernet, R; Bettler, M -O; van Beuzekom, M; Bien, A; Bifani, S; Bird, T; Bizzeti, A; Bjørnstad, P M; Blake, T; Blanc, F; Blouw, J; Blusk, S; Bocci, V; Bondar, A; Bondar, N; Bonivento, W; Borghi, S; Borgia, A; Bowcock, T J V; Bowen, E; Bozzi, C; Brambach, T; van den Brand, J; Bressieux, J; Brett, D; Britsch, M; Britton, T; Brook, N H; Brown, H; Burducea, I; Bursche, A; Busetto, G; Buytaert, J; Cadeddu, S; Callot, O; Calvi, M; Calvo Gomez, M; Camboni, A; Campana, P; Campora Perez, D; Carbone, A; Carboni, G; Cardinale, R; Cardini, A; Carranza-Mejia, H; Carson, L; Carvalho Akiba, K; Casse, G; Castillo Garcia, L; Cattaneo, M; Cauet, Ch; Cenci, R; Charles, M; Charpentier, Ph; Chen, P; Chiapolini, N; Chrzaszcz, M; Ciba, K; Cid Vidal, X; Ciezarek, G; Clarke, P E L; Clemencic, M; Cliff, H V; Closier, J; Coca, C; Coco, V; Cogan, J; Cogneras, E; Collins, P; Comerma-Montells, A; Contu, A; Cook, A; Coombes, M; Coquereau, S; Corti, G; Couturier, B; Cowan, G A; Craik, D C; Cunliffe, S; Currie, R; D'Ambrosio, C; David, P; David, P N Y; Davis, A; De Bonis, I; De Bruyn, K; De Capua, S; De Cian, M; De Miranda, J M; De Paula, L; De Silva, W; De Simone, P; Decamp, D; Deckenhoff, M; Del Buono, L; Déléage, N; Derkach, D; Deschamps, O; Dettori, F; Di Canto, A; Di Ruscio, F; Dijkstra, H; Dogaru, M; Donleavy, S; Dordei, F; Dosil Suárez, A; Dossett, D; Dovbnya, A; Dupertuis, F; Dzhelyadin, R; Dziurda, A; Dzyuba, A; Easo, S; Egede, U; Egorychev, V; Eidelman, S; van Eijk, D; Eisenhardt, S; Eitschberger, U; Ekelhof, R; Eklund, L; El Rifai, I; Elsasser, Ch; Elsby, D; Falabella, A; Färber, C; Fardell, G; Farinelli, C; Farry, S; Fave, V; Ferguson, D; Fernandez Albor, V; Ferreira Rodrigues, F; Ferro-Luzzi, M; Filippov, S; Fiore, M; Fitzpatrick, C; Fontana, M; Fontanelli, F; Forty, R; Francisco, O; Frank, M; Frei, C; Frosini, M; Furcas, S; Furfaro, E; Gallas Torreira, A; Galli, D; Gandelman, M; Gandini, P; Gao, Y; Garofoli, J; Garosi, P; Garra Tico, J; Garrido, L; Gaspar, C; Gauld, R; Gersabeck, E; Gersabeck, M; Gershon, T; Ghez, Ph; Gibson, V; Giubega, L; Gligorov, V V; Göbel, C; Golubkov, D; Golutvin, A; Gomes, A; Gordon, H; Grabalosa Gándara, M; Graciani Diaz, R; Granado Cardoso, L A; Graugés, E; Graziani, G; Grecu, A; Greening, E; Gregson, S; Griffith, P; Grünberg, O; Gui, B; Gushchin, E; Guz, Yu; Gys, T; Hadjivasiliou, C; Haefeli, G; Haen, C; Haines, S C; Hall, S; Hamilton, B; Hampson, T; Hansmann-Menzemer, S; Harnew, N; Harnew, S T; Harrison, J; Hartmann, T; He, J; Head, T; Heijne, V; Hennessy, K; Henrard, P; Hernando Morata, J A; van Herwijnen, E; Hicheur, A; Hicks, E; Hill, D; Hoballah, M; Holtrop, M; Hombach, C; Hopchev, P; Hulsbergen, W; Hunt, P; Huse, T; Hussain, N; Hutchcroft, D; Hynds, D; Iakovenko, V; Idzik, M; Ilten, P; Jacobsson, R; Jaeger, A; Jans, E; Jaton, P; Jawahery, A; Jing, F; John, M; Johnson, D; Jones, C R; Joram, C; Jost, B; Kaballo, M; Kandybei, S; Kanso, W; Karacson, M; Karbach, T M; Kenyon, I R; Ketel, T; Keune, A; Khanji, B; Kochebina, O; Komarov, I; Koopman, R F; Koppenburg, P; Korolev, M; Kozlinskiy, A; Kravchuk, L; Kreplin, K; Kreps, M; Krocker, G; Krokovny, P; Kruse, F; Kucharczyk, M; Kudryavtsev, V; Kvaratskheliya, T; La Thi, V N; Lacarrere, D; Lafferty, G; Lai, A; Lambert, D; Lambert, R W; Lanciotti, E; Lanfranchi, G; Langenbruch, C; Latham, T; Lazzeroni, C; Le Gac, R; van Leerdam, J; Lees, J -P; Lefèvre, R; Leflat, A; Lefrançois, J; Leo, S; Leroy, O; Lesiak, T; Leverington, B; Li, Y; Li Gioi, L; Liles, M; Lindner, R; Linn, C; Liu, B; Liu, G; Lohn, S; Longstaff, I; Lopes, J H; Lopez-March, N; Lu, H; Lucchesi, D; Luisier, J; Luo, H; Machefert, F; Machikhiliyan, I V; Maciuc, F; Maev, O; Malde, S; Manca, G; Mancinelli, G; Marconi, U; Märki, R; Marks, J; Martellotti, G; Martens, A; Martín Sánchez, A; Martinelli, M; Martinez Santos, D; Martins Tostes, D; Massafferri, A; Matev, R; Mathe, Z; Matteuzzi, C; Maurice, E; Mazurov, A; Mc Skelly, B; McCarthy, J; McNab, A; McNulty, R; Meadows, B; Meier, F; Meissner, M; Merk, M; Milanes, D A; Minard, M -N; Molina Rodriguez, J; Monteil, S; Moran, D; Morawski, P; Mordà, A; Morello, M J; Mountain, R; Mous, I; Muheim, F; Müller, K; Muresan, R; Muryn, B; Muster, B; Naik, P; Nakada, T; Nandakumar, R; Nasteva, I; Needham, M; Neubert, S; Neufeld, N; Nguyen, A D; Nguyen, T D; Nguyen-Mau, C; Nicol, M; Niess, V; Niet, R; Nikitin, N; Nikodem, T; Nomerotski, A; Novoselov, A; Oblakowska-Mucha, A; Obraztsov, V; Oggero, S; Ogilvy, S; Okhrimenko, O; Oldeman, R; Orlandea, M; Otalora Goicochea, J M; Owen, P; Oyanguren, A; Pal, B K; Palano, A; Palutan, M; Panman, J; Papanestis, A; Pappagallo, M; Parkes, C; Parkinson, C J; Passaleva, G; Patel, G D; Patel, M; Patrick, G N; Patrignani, C; Pavel-Nicorescu, C; Pazos Alvarez, A; Pellegrino, A; Penso, G; Pepe Altarelli, M; Perazzini, S; Perez Trigo, E; Pérez-Calero Yzquierdo, A; Perret, P; Perrin-Terrin, M; Pessina, G; Petridis, K; Petrolini, A; Phan, A; Picatoste Olloqui, E; Pietrzyk, B; Pilař, T; Pinci, D; Playfer, S; Plo Casasus, M; Polci, F; Polok, G; Poluektov, A; Polycarpo, E; Popov, A; Popov, D; Popovici, B; Potterat, C; Powell, A; Prisciandaro, J; Pritchard, A; Prouve, C; Pugatch, V; Puig Navarro, A; Punzi, G; Qian, W; Rademacker, J H; Rakotomiaramanana, B; Rangel, M S; Raniuk, I; Rauschmayr, N; Raven, G; Redford, S; Reid, M M; dos Reis, A C; Ricciardi, S; Richards, A; Rinnert, K; Rives Molina, V; Roa Romero, D A; Robbe, P; Roberts, D A; Rodrigues, E; Rodriguez Perez, P; Roiser, S; Romanovsky, V; Romero Vidal, A; Rouvinet, J; Ruf, T; Ruffini, F; Ruiz, H; Ruiz Valls, P; Sabatino, G; Saborido Silva, J J; Sagidova, N; Sail, P; Saitta, B; Salustino Guimaraes, V; Salzmann, C; Sanmartin Sedes, B; Sannino, M; Santacesaria, R; Santamarina Rios, C; Santovetti, E; Sapunov, M; Sarti, A; Satriano, C; Satta, A; Savrie, M; Savrina, D; Schaack, P; Schiller, M; Schindler, H; Schlupp, M; Schmelling, M; Schmidt, B; Schneider, O; Schopper, A; Schune, M -H; Schwemmer, R; Sciascia, B; Sciubba, A; Seco, M; Semennikov, A; Sepp, I; Serra, N; Serrano, J; Seyfert, P; Shapkin, M; Shapoval, I; Shatalov, P; Shcheglov, Y; Shears, T; Shekhtman, L; Shevchenko, O; Shevchenko, V; Shires, A; Silva Coutinho, R; Sirendi, M; Skwarnicki, T; Smith, N A; Smith, E; Smith, J; Smith, M; Sokoloff, M D; Soler, F J P; Soomro, F; Souza, D; Souza De Paula, B; Spaan, B; Sparkes, A; Spradlin, P; Stagni, F; Stahl, S; Steinkamp, O; Stoica, S; Stone, S; Storaci, B; Straticiuc, M; Straumann, U; Subbiah, V K; Sun, L; Swientek, S; Syropoulos, V; Szczekowski, M; Szczypka, P; Szumlak, T; T'Jampens, S; Teklishyn, M; Teodorescu, E; Teubert, F; Thomas, C; Thomas, E; van Tilburg, J; Tisserand, V; Tobin, M; Tolk, S; Tonelli, D; Topp-Joergensen, S; Torr, N; Tournefier, E; Tourneur, S; Tran, M T; Tresch, M; Tsaregorodtsev, A; Tsopelas, P; Tuning, N; Ubeda Garcia, M; Ukleja, A; Urner, D; Ustyuzhanin, A; Uwer, U; Vagnoni, V; Valenti, G; Vallier, A; Van Dijk, M; Vazquez Gomez, R; Vazquez Regueiro, P; Vázquez Sierra, C; Vecchi, S; Velthuis, J J; Veltri, M; Veneziano, G; Vesterinen, M; Viaud, B; Vieira, D; Vilasis-Cardona, X; Vollhardt, A; Volyanskyy, D; Voong, D; Vorobyev, A; Vorobyev, V; Voß, C; Voss, H; Waldi, R; Wallace, C; Wallace, R; Wandernoth, S; Wang, J; Ward, D R; Watson, N K; Webber, A D; Websdale, D; Whitehead, M; Wicht, J; Wiechczynski, J; Wiedner, D; Wiggers, L; Wilkinson, G; Williams, M P; Williams, M; Wilson, F F; Wimberley, J; Wishahi, J; Witek, M; Wotton, S A; Wright, S; Wu, S; Wyllie, K; Xie, Y; Xing, Z; Yang, Z; Young, R; Yuan, X; Yushchenko, O; Zangoli, M; Zavertyaev, M; Zhang, F; Zhang, L; Zhang, W C; Zhang, Y; Zhelezov, A; Zhokhov, A; Zhong, L; Zvyagin, A

    2013-01-01

    The charmless decays $B^{\\pm}\\to K^{\\pm}\\pi^+\\pi^-$ and $B^{\\pm}\\to K^{\\pm}K^+K^-$ are reconstructed using data, corresponding to an integrated luminosity of 1.0 fb$^{-1}$, collected by LHCb in 2011. The inclusive charge asymmetries of these modes are measured as $A_{C\\!P}(B^{\\pm}\\to K^{\\pm}\\pi^+\\pi^-) = 0.032 \\pm 0.008 {\\mathrm{\\,(stat)}} \\pm 0.004 {\\mathrm{\\,(syst)}} \\pm 0.007 (J/\\psi K^{\\pm})$ and $A_{C\\!P}(B^{\\pm}\\to K^{\\pm}K^+K^-) = -0.043 \\pm 0.009 {\\mathrm{\\,(stat)}} \\pm 0.003 {\\mathrm{\\,(syst)}} \\pm 0.007 (J/\\psi K^{\\pm})$, where the third uncertainty is due to the $C\\!P$ asymmetry of the $B^{\\pm}\\to J/\\psi K^{\\pm}$ reference mode. The significance of $A_{C\\!P}(B^{\\pm}\\to K^{\\pm}K^+K^-)$ exceeds three standard deviations and is the first evidence of an inclusive $C\\!P$ asymmetry in charmless three-body $B$ decays. In addition to the inclusive $C\\!P$ asymmetries, larger asymmetries are observed in localised regions of phase space.

  8. Technology of Urban, Interurban and Rural Passenger Transport

    Directory of Open Access Journals (Sweden)

    Gordana Štefančić

    2006-01-01

    Full Text Available The work will consider the significance of various publictransport modes, since different methods of travel that form thetransport system are interconnected. The application of thelevel of service in one mode influences other transport modesand changes depending on the type of travel and is divided inthree groups: urban, interurban and rural travel. In consideringthe significance of urban public transport there are three levelsof trip-end generation/attraction, with which six types of urbantravel can be identified. lnterurban travel is presented throughtwo main transport modes, rail and bus. Apart from businesstrips, air travel is relatively insignificant, primarily because ofthe prices and small distances. In rural areas, characterized bylow population density, there is the problem of travelling of theelderly people, as well as those without cars, as the difficulty ofproviding economic public transport services has increased becausethe number of carried passengers is small. This results inthe reduction in mobility and the quality of life. Attempts havebeen made to improve the standard of provision of public transportservices by introducing unconventional transport means.

  9. Changes of E-KERS Rules to Make F1 More Relevant to Road Cars

    Directory of Open Access Journals (Sweden)

    Albert Boretti

    2018-01-01

    Full Text Available Today’s F1 hybrid cars are based on very similar power units made up of about the same internal combustion engine (ICE and energy recovery system (ERS. Because of restrictive design rules permitting too much fuel per race, the internal combustion engine is not particularly fuel efficient. The methodology is based on lap time simulations and telemetry data for a F1 H car covering one lap of the Monaco Grand Prix. The methodology is based on lap time simulations and telemetry data for a F1 H car covering one lap of the Monaco Grand Prix. The present limit of 100 kg of fuel per race is excessive. The low power energy recovery system is used strategically rather than fuel savings recovering very little braking energy. The 4 MJ of storable energy is used only when it is strategically needed. The 2 MJ of recoverable energy allowed per lap are almost never collected. To return to be technically attractive, F1 should permit much more freedom in the definition of the ICE and the ERS. As the goal of the rules should be lowering the fuel consumption while keeping technical and sporting interest high, the best solution is more freedom to achieve the fastest car within more stringent limits of fuel economy. A real limit to the total fuel consumption for a race track like Monte Carlo should be not more than 80 kg of fuel. This would translate in more energy recovery to the ERS per lap and better fuel efficiency of the ICE and will certainly help more the design of passenger cars.

  10. Low speed hybrid generalized predictive control of a gasoline-propelled car.

    Science.gov (United States)

    Romero, M; de Madrid, A P; Mañoso, C; Milanés, V

    2015-07-01

    Low-speed driving in traffic jams causes significant pollution and wasted time for commuters. Additionally, from the passengers׳ standpoint, this is an uncomfortable, stressful and tedious scene that is suitable to be automated. The highly nonlinear dynamics of car engines at low-speed turn its automation in a complex problem that still remains as unsolved. Considering the hybrid nature of the vehicle longitudinal control at low-speed, constantly switching between throttle and brake pedal actions, hybrid control is a good candidate to solve this problem. This work presents the analytical formulation of a hybrid predictive controller for automated low-speed driving. It takes advantage of valuable characteristics supplied by predictive control strategies both for compensating un-modeled dynamics and for keeping passengers security and comfort analytically by means of the treatment of constraints. The proposed controller was implemented in a gas-propelled vehicle to experimentally validate the adopted solution. To this end, different scenarios were analyzed varying road layouts and vehicle speeds within a private test track. The production vehicle is a commercial Citroën C3 Pluriel which has been modified to automatically act over its throttle and brake pedals. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

  11. 77 FR 70538 - Final Decision That Certain Canadian-Certified Vehicles Are Eligible for Importation

    Science.gov (United States)

    2012-11-26

    .... 126 for all passenger cars and all multipurpose passenger vehicles, trucks, and buses with a GVWR of 4... vehicles, U.S. Standard Canadian standard Passenger cars trucks, and buses with a GVWR of 4,536 kg (10,000... Protection. CMVSS 214--Side Door X X Strength. FMVSS 222--School Bus Passenger CMVSS 222--School Bus School...

  12. ISSUES OF ORGANIZING THE PASSENGER TRANSPORTATION ON US RAILWAYS

    Directory of Open Access Journals (Sweden)

    R. H. Korobiova

    2017-04-01

    Full Text Available Purpose. The paper focuses on a study of the US railway transport organization management during passenger transportation. Methodology. Studies were carried out on the basis of the analysis of literature sources and reporting data on passenger transportation in the USA. Findings. Negative trends in the work of the passenger complex of the Ukrainian railways are the slowdown in the volumes of transportation, the progressive aging of the rolling stock and the overall activity running at a loss for Ukrzaliznytsia. In this regard, the actual task for domestic rail transport is the implementation of industry reforms. Therefore, the paper presented the study of the experience of organizing the passenger transportation on US railways, whose peculiarity is the extremely high degree of competition between modes of transport. As a result of the conducted analysis for working conditions of the US and Ukrainian railways, the general conditions for the functioning of the railways in both countries connected with passenger transportation securing have been established. It was found that general condition for execution of railway passenger transportation for the United States and Ukraine is the subsidization of this activity and combined use of infrastructure for the freight and passengers’ transportations. In this connection, when developing approaches to reforming the passenger economy of Ukraine's railways, it is advisable to use the experience of the United States in assessing the social effectiveness of rail transport, the impact of passenger transportation on the conditions of freight trains handling, and combined use of railway infrastructure by freight and passenger companies. Originality. The author determined the general trends in the development of passenger railway transportation in the US and Ukraine. Practical value. The resulted methods of organizing the operation of the US railway passenger transportation complex can be adapted to solve

  13. Trends in passenger transport and freight energy use in Spain

    International Nuclear Information System (INIS)

    Mendiluce, Maria; Schipper, Lee

    2011-01-01

    This paper provides for the first time a complete analysis of recent trends in activity, carbon emissions, modal shares, energy intensities, vehicle use and fuels in the Spanish transport system from 1990 to 2008 and discusses policy options. Passenger and freight activities have increased in Spain and are projected to continue, presenting a challenge for sustainable mobility efforts; emissions have increased, mainly fueled by the rise in activity; modal shares have pulled away from public transport, with a decrease in bus and rail, towards an increase in car and air travel; energy intensities, though initially decreasing, are currently increasing; and fuel use has taken over 37% of Spanish final energy consumption. To target these issues the Spanish government has focused its efforts in targeting energy efficiency through dieselization, which has not led to positive results. More recently policies and measures have been directed towards redirecting modal shares and diversifying the fuel mix. Little has been done to reduce activity besides some anecdotic public awareness campaigns. Activity reduction may be achieved with regulations, restrictions and mobility plans; by increasing high speed rail and rail freight transport; by improving intermodality and tying the Spanish rail network with the EU; and with more urban transport planning at local level. - Highlights: → Complete analysis of recent trends in Spanish transport system from 1990 to 2008. → Passenger and freight activities have driven GHG emissions increase. → Modal shares have pulled away from public transport. → Policy efforts targeted energy efficiency and redirecting modal shares and diversifying the fuel mix. → Little has been done to reduce activity.

  14. Passenger transport and household activity patterns

    DEFF Research Database (Denmark)

    Jørgensen, Kaj

    1997-01-01

    Review of Danish passenger transport patterns and analysis of energy consumption, emissions and safety impacts for selected typical households' travelling......Review of Danish passenger transport patterns and analysis of energy consumption, emissions and safety impacts for selected typical households' travelling...

  15. Child Passenger Safety Training for Pediatric Interns: Does it Work?

    Science.gov (United States)

    Morrissey, Dina; Riese, Alison; Violano, Pina; Lapidus, Garry; Baird, Janette; Mello, Michael J

    2016-03-01

    Evaluate the efficacy of a child passenger safety (CPS) educational intervention on the CPS-related knowledge, attitude and anticipatory guidance behaviors of pediatric interns. All subjects were surveyed at baseline and 6 months. Intervention interns attended a CPS training module which included viewing an educational video, observing a car seat inspection appointment, hands-on practice and completion of a post-intervention survey. All 16 intervention interns completed the initial survey, the intervention and the immediate-post questionnaire. Thirteen (81%) completed the 6-month follow-up. The baseline survey was completed by 27/40 (67%) of control interns, 28/40 (70%) submitted a follow-up. The proportion of intervention interns who self-reported giving CPS guidance at all well-child visits increased by 31.3% (95% CI 6.1,56.5%); the control group had no change. Similar results were seen with self-reported knowledge and attitude. A CPS training module increases pediatric interns' knowledge, improves attitudes, and self-reported behaviors regarding CPS-related anticipatory guidance.

  16. Analyzing injury severity of bus passengers with different movements.

    Science.gov (United States)

    Li, Duo; Zhao, Yifei; Bai, Qiang; Zhou, Bei; Ling, Hongbiao

    2017-07-04

    Though public transport vehicles are rarely involved in mass casualty accidents, when they are, the number of injuries and fatalities is usually high due to the high passenger capacity. Of the few studies that have been conducted on bus safety, the majority focused on vehicle safety features, road environmental factors, as well as driver characteristics. Nevertheless, few studies have attempted to investigate the underlying risk factors related to bus occupants. This article presents an investigation aimed at identifying the risk factors affecting injury severity of bus passengers with different movements. Three different passenger movement types including standing, seated, and boarding/alighting were analyzed individually using classification and regression tree (CART) method based on publicly available accident database of Great Britain. According to the results of exploratory analyses, passenger age and vehicle maneuver are associated with passenger injury severity in all 3 types of accidents. Moreover, the variable "skidding and overturning" is associated with injury severity of seated passengers and driver age is correlated with injury severity of standing and boarding/alighting passengers. The CART method shows its ability to identify and easily explain the complicated patterns affecting passenger injury severity. Several countermeasures to reduce bus passenger injury severity are recommended.

  17. Advanced vehicle dynamics of heavy trucks with the perspective of road safety

    Science.gov (United States)

    Trigell, Annika Stensson; Rothhämel, Malte; Pauwelussen, Joop; Kural, Karel

    2017-10-01

    This paper presents state-of-the art within advanced vehicle dynamics of heavy trucks with the perspective of road safety. The most common accidents with heavy trucks involved are truck against passenger cars. Safety critical situations are for example loss of control (such as rollover and lateral stability) and a majority of these occur during speed when cornering. Other critical situations are avoidance manoeuvre and road edge recovery. The dynamic behaviour of heavy trucks have significant differences compared to passenger cars and as a consequence, successful application of vehicle dynamic functions for enhanced safety of trucks might differ from the functions in passenger cars. Here, the differences between vehicle dynamics of heavy trucks and passenger cars are clarified. Advanced vehicle dynamics solutions with the perspective of road safety of trucks are presented, beginning with the topic vehicle stability, followed by the steering system, the braking system and driver assistance systems that differ in some way from that of passenger cars as well.

  18. The market for gasoline cars and diesel cars

    International Nuclear Information System (INIS)

    Verboven, F.

    1999-01-01

    In Europe the tax tariff is much lower for diesel fuel than for gasoline. This benefit is used by manufacturers to increase the price of diesel-fueled cars, which limits the possibility to control the use of diesel cars by means of a fiscal policy (tax incidence). Attention is paid to the impact of fiscal advantages for diesel cars on the purchasing behavior of the consumer and the pricing policy (price discrimination) of the car manufacturers. 1 ref

  19. [Comfort of crew and passengers and atmospheric pressure, noise, wind speed in high-speed train of Shijiazhuang-Taiyuan passenger dedicated line].

    Science.gov (United States)

    Zhai, Yi-biao; Huo, Wei; Liu, Qiao-ying; Chen, Bao-shan; Zhang, Jin-long; Shi, Lei

    2012-11-01

    To explore the crew and passengers' comfort on the Shijiazhuang-Taiyuan passenger dedicated line and physical factors, such as air pressure, noise, wind speed. Comfort investigation of all the crew (n = 244) and passengers (n = 377) on the Shijiazhuang-Taiyuan passenger dedicated line at speed of 250 km/h and 200 km/h and the detection of the air pressure, noise and wind speed were performed in 2011. Significantly higher ratio of comfortable feeling, lower ratio of seriously discomfortable feeling were observed in crew and passengers at 200 km/h compared with those at 250 km/h (P noise in passengers at 200 km/h. No significant difference was observed in ear discomfort induced by air pressure and noise among crew, and the duration of disappearance of discomfortable feeling among passengers between 200 km/h and 250 km/h. The noise in carriages exceeded the related standard when the high-speed train passing through the tunnels. The individuals feel more comfortable at 200 km/h than 250 km/h in this line., which may be related with rapid variation of wind speed and noise when the train passes through the tunnels with high speed.

  20. Adaptation Model for Corporate Car Sharing in the Car Rental Industry

    OpenAIRE

    Matthes, Martin

    2016-01-01

    The focus of this thesis was on developing an adaption model for implementing a corporate car sharing service within the existing infrastructure of a car rental company. The investigated case companies were a leading Finnish car rental franchisee and an international car sharing subsidiary, largely owned by the car rental franchisor, which offers corporate car sharing solutions in major European countries. Adapting this new service in Finland will help the car rental franchisee to assert its ...

  1. How Important is the Integration of Public Passenger Transport

    Directory of Open Access Journals (Sweden)

    Mrníková Michaela

    2017-11-01

    Full Text Available The significance of the issue of an effective mode of passenger transport is currently increasing. On the one hand, there is the increasing economic demand of public passenger transport, on the other hand, there is the growing traffic share of individual automobile transport. The objective of the paper is to analyze public passenger transport without mutual integration of individual transport systems resulting in the fact that it is not sufficiently able to compete with individual automobile transport. It is proposed the integration of different modes of public passenger transport as a way to increase the competitiveness of public passenger transport. Aim of this paper is to analyze the individual elements of integration systems and describe why integration of public passenger transport systems is needed.

  2. THE RISK OF INJURY AND VEHICLE DAMAGE SEVERITY IN VEHICLE MISMATCHED SIDE IMPACT CRASHES IN BRITISH COLUMBIA

    Directory of Open Access Journals (Sweden)

    Ediriweera DESAPRIYA

    2005-01-01

    Full Text Available As occupant protection offered by new passenger vehicles has improved, there has been growing concern about the harm that some vehicle designs may inflict on occupants of other vehicles with which they collide. Preceding analyses of crash statistics have clearly demonstrated the incompatibility between passenger sedan cars (PS and pick-up trucks (PU involved in side impact crashes in British Columbia. A comparison of light truck and passenger car crashes in previous literature reveals that light truck vehicles inflict greater harm than passenger cars for a number of reasons including their greater weight, stiffer structure, and higher ride height. These features place occupants of passenger cars at a disadvantage should they be involved in a collision with a light truck vehicle. The injury risk for passenger sedan car occupants is greater than the risk for pick-up truck occupants in two-vehicle crashes (Odds Ratio (OR 1.87; 95% Confidence Interval (CI 1.38-2.52. In addition, the risk of vehicle damage severity was increased for passenger cars compared with pick-up trucks (write off vehicle-OR 5.35; 95% CI 3.75-7.63, severely damaged vehicles-OR 5.87; 95% CI 4.79–7.19, moderately damaged vehicles-OR 2.86; 95% CI 2.44–3.36. There is strong justification for injury prevention experts and policy makers to step up motor vehicle crash injury prevention advocacy by implementing evidence-based policies to reduce rates of injury as a result of passenger sedan cars and pick-up trucks involved in side impact crashes in the province of British Columbia.

  3. Comparison of airline passenger oxygen systems.

    Science.gov (United States)

    Byrne, N J

    1995-08-01

    The principal sources of oxygen for inflight passenger use, scheduled and unscheduled, are examined. Present practices of assessment of the passenger's "fitness to fly" are described. Three partner airlines, British Airways, U.S. Air, and Qantas, catering for more than 8000 oxygen requests annually, are compared. Analysis of customer use suggests that medical oxygen requests are frequently not clinically justified. The growth in demand, for both scheduled and unscheduled use of an expensive resource, supports the need for a "recommended best practice" among carriers. Passengers with respiratory disorders who will most benefit from inflight oxygen are vulnerable either to hypoxia or asthma.

  4. Distortionary company car taxation: deadweight losses through increased car ownership

    NARCIS (Netherlands)

    van Ommeren, J.N.; Gutierrez Puigarnau, E.

    2013-01-01

    We analyse the effects of distortionary company car taxation through increased household car consumption for the Netherlands. We use several identification strategies and demonstrate that for about 20 % of households company car possession increases car ownership. The annual welfare loss of

  5. Winter mass concentrations of carbon species in PM10, PM 2.5 and PM1 in Zagreb air, Croatia.

    Science.gov (United States)

    Godec, Ranka; Čačković, Mirjana; Šega, Krešimir; Bešlić, Ivan

    2012-11-01

    The purpose of our investigation was to examine the mass concentrations of EC, OC and TC (EC + OC) in PM(10), PM(2.5) and PM(1) particle fractions. Daily PM(10), PM(2.5) and PM(1) samples were collected at an urban background monitoring site in Zagreb during winter 2009. Average OC and EC mass concentrations were 11.9 and 1.8 μg m(-3) in PM(10), 9.0 and 1.4 μg m(-3) in PM(2.5), and 5.5 and 1.1 μg m(-3) in PM(1). Average OC/EC ratios in PM(10), PM(2.5), and PM(1) were 7.4, 6.9 and 5.4, respectively.

  6. Rock Magnetic Characterization of fine Particles from car Engines, Break pads and Tobacco: An Environmental Pilot Study

    Science.gov (United States)

    Herrero-Bervera, E.; Lopez, V. A.; Gerstnecker, K.; Swilley, B.

    2017-12-01

    Today, it is very well known that small magnetic particles are very harmful to the health of humans. For the first time we have conducted an environmental pilot study of fine magnetic particles on the island of Oahu, Hawaii, of particulate matter (pm) 60, pm=10, and pm= 2.5. In order to do a rock magnetic characterization we have preformed low field susceptibility versus temperature (k-T) experiments to determine the Curie points of small particles collected from exhaust pipes, as well as from brake pads of 4 different types of car engines using octane ratings of 85, 87 and 92. The Curie point determinations are very well defined and range from 292 °C through 393 °C to 660 °C. In addition, we have conducted magnetic granulometry experiments on raw tobacco, burnt ashes as well as on car engines and brake pads in question. The results of the experiments show ferro- and ferrimagnetic hysteresis loops with magnetic grain sizes ranging from superparamagnetic-multidomain (SP_MD), multi-domain (MD) and pseudo-single domain (PSD) shown on the modified Day et al. diagram of Dunlop (2002). Thus far, the results we have obtained from this pilot study are in agreement with other studies conducted from cigarette ashes from Bulgaria (Jordanova et al., 2005). Our results could be correlated to the traffic-related PM in Rome, Italy where the SP fraction mainly occurs as coating of MD particles that originated by localized stress in the oxidized outer shell surrounding the unoxidized core of magnetite like grains as published by Sagnotti and Winkler (2012).

  7. Measurements of the branching fractions and $C\\!P$ asymmetries of $B^{\\pm} \\to J\\!/\\!\\psi\\, \\pi^{\\pm}$ and $B^{\\pm} \\to \\psi(2S) \\pi^{\\pm}$ decays

    CERN Document Server

    Aaij, R; Adeva, B; Adinolfi, M; Adrover, C; Affolder, A; Ajaltouni, Z; Albrecht, J; Alessio, F; Alexander, M; Ali, S; Alkhazov, G; Alvarez Cartelle, P; Alves Jr, A A; Amato, S; Amhis, Y; Anderson, J; Appleby, R B; Aquines Gutierrez, O; Archilli, F; Artamonov, A; Artuso, M; Aslanides, E; Auriemma, G; Bachmann, S; Back, J J; Balagura, V; Baldini, W; Barlow, R J; Barschel, C; Barsuk, S; Barter, W; Bates, A; Bauer, C; Bauer, Th; Bay, A; Bediaga, I; Belogurov, S; Belous, K; Belyaev, I; Ben-Haim, E; Benayoun, M; Bencivenni, G; Benson, S; Benton, J; Bernet, R; Bettler, M-O; van Beuzekom, M; Bien, A; Bifani, S; Bird, T; Bizzeti, A; Bjørnstad, P M; Blake, T; Blanc, F; Blanks, C; Blouw, J; Blusk, S; Bobrov, A; Bocci, V; Bondar, A; Bondar, N; Bonivento, W; Borghi, S; Borgia, A; Bowcock, T J V; Bozzi, C; Brambach, T; van den Brand, J; Bressieux, J; Brett, D; Britsch, M; Britton, T; Brook, N H; Brown, H; Büchler-Germann, A; Burducea, I; Bursche, A; Buytaert, J; Cadeddu, S; Callot, O; Calvi, M; Calvo Gomez, M; Camboni, A; Campana, P; Carbone, A; Carboni, G; Cardinale, R; Cardini, A; Carson, L; Carvalho Akiba, K; Casse, G; Cattaneo, M; Cauet, Ch; Charles, M; Charpentier, Ph; Chiapolini, N; Ciba, K; Cid Vidal, X; Ciezarek, G; Clarke, P E L; Clemencic, M; Cliff, H V; Closier, J; Coca, C; Coco, V; Cogan, J; Collins, P; Comerma-Montells, A; Contu, A; Cook, A; Coombes, M; Corti, G; Couturier, B; Cowan, G A; Currie, R; D'Ambrosio, C; David, P; David, P N Y; De Bonis, I; De Bruyn, K; De Capua, S; De Cian, M; De Miranda, J M; De Paula, L; De Simone, P; Decamp, D; Deckenhoff, M; Degaudenzi, H; Del Buono, L; Deplano, C; Derkach, D; Deschamps, O; Dettori, F; Dickens, J; Dijkstra, H; Diniz Batista, P; Domingo Bonal, F; Donleavy, S; Dordei, F; Dosil Suárez, A; Dossett, D; Dovbnya, A; Dupertuis, F; Dzhelyadin, R; Dziurda, A; Easo, S; Egede, U; Egorychev, V; Eidelman, S; van Eijk, D; Eisele, F; Eisenhardt, S; Ekelhof, R; Eklund, L; Elsasser, Ch; Elsby, D; Esperante Pereira, D; Falabella, A; Färber, C; Fardell, G; Farinelli, C; Farry, S; Fave, V; Fernandez Albor, V; Ferro-Luzzi, M; Filippov, S; Fitzpatrick, C; Fontana, M; Fontanelli, F; Forty, R; Francisco, O; Frank, M; Frei, C; Frosini, M; Furcas, S; Gallas Torreira, A; Galli, D; Gandelman, M; Gandini, P; Gao, Y; Garnier, J-C; Garofoli, J; Garra Tico, J; Garrido, L; Gascon, D; Gaspar, C; Gauld, R; Gauvin, N; Gersabeck, M; Gershon, T; Ghez, Ph; Gibson, V; Gligorov, V V; Göbel, C; Golubkov, D; Golutvin, A; Gomes, A; Gordon, H; Grabalosa Gándara, M; Graciani Diaz, R; Granado Cardoso, L A; Graugés, E; Graziani, G; Grecu, A; Greening, E; Gregson, S; Gui, B; Gushchin, E; Guz, Yu; Gys, T; Hadjivasiliou, C; Haefeli, G; Haen, C; Haines, S C; Hampson, T; Hansmann-Menzemer, S; Harji, R; Harnew, N; Harrison, J; Harrison, P F; Hartmann, T; He, J; Heijne, V; Hennessy, K; Henrard, P; Hernando Morata, J A; van Herwijnen, E; Hicks, E; Holubyev, K; Hopchev, P; Hulsbergen, W; Hunt, P; Huse, T; Huston, R S; Hutchcroft, D; Hynds, D; Iakovenko, V; Ilten, P; Imong, J; Jacobsson, R; Jaeger, A; Jahjah Hussein, M; Jans, E; Jansen, F; Jaton, P; Jean-Marie, B; Jing, F; John, M; Johnson, D; Jones, C R; Jost, B; Kaballo, M; Kandybei, S; Karacson, M; Karbach, T M; Keaveney, J; Kenyon, I R; Kerzel, U; Ketel, T; Keune, A; Khanji, B; Kim, Y M; Knecht, M; Koopman, R F; Koppenburg, P; Korolev, M; Kozlinskiy, A; Kravchuk, L; Kreplin, K; Kreps, M; Krocker, G; Krokovny, P; Kruse, F; Kruzelecki, K; Kucharczyk, M; Kudryavtsev, V; Kvaratskheliya, T; La Thi, V N; Lacarrere, D; Lafferty, G; Lai, A; Lambert, D; Lambert, R W; Lanciotti, E; Lanfranchi, G; Langenbruch, C; Latham, T; Lazzeroni, C; Le Gac, R; van Leerdam, J; Lees, J-P; Lefèvre, R; Leflat, A; Lefrançois, J; Leroy, O; Lesiak, T; Li, L; Li Gioi, L; Lieng, M; Liles, M; Lindner, R; Linn, C; Liu, B; Liu, G; von Loeben, J; Lopes, J H; Lopez Asamar, E; Lopez-March, N; Lu, H; Luisier, J; Mac Raighne, A; Machefert, F; Machikhiliyan, I V; Maciuc, F; Maev, O; Magnin, J; Malde, S; Mamunur, R M D; Manca, G; Mancinelli, G; Mangiafave, N; Marconi, U; Märki, R; Marks, J; Martellotti, G; Martens, A; Martin, L; Martín Sánchez, A; Martinelli, M; Martinez Santos, D; Massafferri, A; Mathe, Z; Matteuzzi, C; Matveev, M; Maurice, E; Maynard, B; Mazurov, A; McGregor, G; McNulty, R; Meissner, M; Merk, M; Merkel, J; Miglioranzi, S; Milanes, D A; Minard, M-N; Molina Rodriguez, J; Monteil, S; Moran, D; Morawski, P; Mountain, R; Mous, I; Muheim, F; Müller, K; Muresan, R; Muryn, B; Muster, B; Mylroie-Smith, J; Naik, P; Nakada, T; Nandakumar, R; Nasteva, I; Needham, M; Neufeld, N; Nguyen, A D; Nguyen-Mau, C; Nicol, M; Niess, V; Nikitin, N; Nikodem, T; Nomerotski, A; Novoselov, A; Oblakowska-Mucha, A; Obraztsov, V; Oggero, S; Ogilvy, S; Okhrimenko, O; Oldeman, R; Orlandea, M; Otalora Goicochea, J M; Owen, P; Pal, B K; Palacios, J; Palano, A; Palutan, M; Panman, J; Papanestis, A; Pappagallo, M; Parkes, C; Parkinson, C J; Passaleva, G; Patel, G D; Patel, M; Paterson, S K; Patrick, G N; Patrignani, C; Pavel-Nicorescu, C; Pazos Alvarez, A; Pellegrino, A; Penso, G; Pepe Altarelli, M; Perazzini, S; Perego, D L; Perez Trigo, E; Pérez-Calero Yzquierdo, A; Perret, P; Perrin-Terrin, M; Pessina, G; Petrolini, A; Phan, A; Picatoste Olloqui, E; Pie Valls, B; Pietrzyk, B; Pilař, T; Pinci, D; Plackett, R; Playfer, S; Plo Casasus, M; Polok, G; Poluektov, A; Polycarpo, E; Popov, D; Popovici, B; Potterat, C; Powell, A; Prisciandaro, J; Pugatch, V; Puig Navarro, A; Qian, W; Rademacker, J H; Rakotomiaramanana, B; Rangel, M S; Raniuk, I; Raven, G; Redford, S; Reid, M M; dos Reis, A C; Ricciardi, S; Richards, A; Rinnert, K; Roa Romero, D A; Robbe, P; Rodrigues, E; Rodrigues, F; Rodriguez Perez, P; Rogers, G J; Roiser, S; Romanovsky, V; Rosello, M; Rouvinet, J; Ruf, T; Ruiz, H; Sabatino, G; Saborido Silva, J J; Sagidova, N; Sail, P; Saitta, B; Salzmann, C; Sannino, M; Santacesaria, R; Santamarina Rios, C; Santinelli, R; Santovetti, E; Sapunov, M; Sarti, A; Satriano, C; Satta, A; Savrie, M; Savrina, D; Schaack, P; Schiller, M; Schindler, H; Schleich, S; Schlupp, M; Schmelling, M; Schmidt, B; Schneider, O; Schopper, A; Schune, M-H; Schwemmer, R; Sciascia, B; Sciubba, A; Seco, M; Semennikov, A; Senderowska, K; Sepp, I; Serra, N; Serrano, J; Seyfert, P; Shapkin, M; Shapoval, I; Shatalov, P; Shcheglov, Y; Shears, T; Shekhtman, L; Shevchenko, O; Shevchenko, V; Shires, A; Silva Coutinho, R; Skwarnicki, T; Smith, N A; Smith, E; Sobczak, K; Soler, F J P; Solomin, A; Soomro, F; Souza De Paula, B; Spaan, B; Sparkes, A; Spradlin, P; Stagni, F; Stahl, S; Steinkamp, O; Stoica, S; Stone, S; Storaci, B; Straticiuc, M; Straumann, U; Subbiah, V K; Swientek, S; Szczekowski, M; Szczypka, P; Szumlak, T; T'Jampens, S; Teodorescu, E; Teubert, F; Thomas, C; Thomas, E; van Tilburg, J; Tisserand, V; Tobin, M; Tolk, S; Topp-Joergensen, S; Torr, N; Tournefier, E; Tourneur, S; Tran, M T; Tsaregorodtsev, A; Tuning, N; Ubeda Garcia, M; Ukleja, A; Uwer, U; Vagnoni, V; Valenti, G; Vazquez Gomez, R; Vazquez Regueiro, P; Vecchi, S; Velthuis, J J; Veltri, M; Viaud, B; Videau, I; Vieira, D; Vilasis-Cardona, X; Visniakov, J; Vollhardt, A; Volyanskyy, D; Voong, D; Vorobyev, A; Vorobyev, V; Voss, H; Waldi, R; Wandernoth, S; Wang, J; Ward, D R; Watson, N K; Webber, A D; Websdale, D; Whitehead, M; Wiedner, D; Wiggers, L; Wilkinson, G; Williams, M P; Williams, M; Wilson, F F; Wishahi, J; Witek, M; Witzeling, W; Wotton, S A; Wyllie, K; Xie, Y; Xing, F; Xing, Z; Yang, Z; Young, R; Yushchenko, O; Zangoli, M; Zavertyaev, M; Zhang, F; Zhang, L; Zhang, W C; Zhang, Y; Zhelezov, A; Zhong, L; Zvyagin, A

    2012-01-01

    A study of $B^{\\pm} \\to J\\!/\\!\\psi\\, \\pi^{\\pm}$ and $B^{\\pm} \\to \\psi(2S) \\pi^{\\pm}$ decays is performed with data corresponding to $0.37\\,{\\rm fb}^{-1}$ of proton-proton collisions at $\\sqrt{s}=7\\,\\mathrm{Te\\kern -0.1em V}$. Their branching fractions are found to be \\begin{eqnarray*} \\mathcal{B}(B^{\\pm} \\to J\\!/\\!\\psi\\, \\pi^{\\pm}) &=& (3.88 \\pm 0.11 \\pm 0.15) \\times 10^{-5}\\ {\\rm and}\\\\ \\mathcal{B}(B^{\\pm} \\to \\psi(2S) \\pi^{\\pm}) &=& (2.52 \\pm 0.26 \\pm 0.15) \\times 10^{-5}, \\end{eqnarray*} where the first uncertainty is related to the statistical size of the sample and the second quantifies systematic effects. The measured $C\\!P$ asymmetries in these modes are \\begin{eqnarray*} A_{CP}^{J\\!/\\!\\psi\\, \\pi} &=& 0.005 \\pm 0.027 \\pm 0.011\\ {\\rm and} \\\\ A_{CP}^{\\psi(2S) \\pi} &=& 0.048 \\pm 0.090 \\pm 0.011 \\end{eqnarray*} with no evidence of direct $C\\!P$ violation seen.

  8. 150 Passenger Commercial Aircraft

    Science.gov (United States)

    Bucovsky, Adrian; Romli, Fairuz I.; Rupp, Jessica

    2002-01-01

    It has been projected that the need for a short-range mid-sized, aircraft is increasing. The future strategy to decrease long-haul flights will increase the demand for short-haul flights. Since passengers prefer to meet their destinations quickly, airlines will increase the frequency of flights, which will reduce the passenger load on the aircraft. If a point-to-point flight is not possible, passengers will prefer only a one-stop short connecting flight to their final destination. A 150-passenger aircraft is an ideal vehicle for these situations. It is mid-sized aircraft and has a range of 3000 nautical miles. This type of aircraft would market U.S. domestic flights or inter-European flight routes. The objective of the design of the 150-passenger aircraft is to minimize fuel consumption. The configuration of the aircraft must be optimized. This aircraft must meet CO2 and NOx emissions standards with minimal acquisition price and operating costs. This report contains all the work that has been performed for the completion of the design of a 150 passenger commercial aircraft. The methodology used is the Technology Identification, Evaluation, and Selection (TIES) developed at Georgia Tech Aerospace Systems Design laboratory (ASDL). This is an eight-step conceptual design process to evaluate the probability of meeting the design constraints. This methodology also allows for the evaluation of new technologies to be implemented into the design. The TIES process begins with defining the problem with a need established and a market targeted. With the customer requirements set and the target values established, a baseline concept is created. Next, the design space is explored to determine the feasibility and viability of the baseline aircraft configuration. If the design is neither feasible nor viable, new technologies can be implemented to open up the feasible design space and allow for a plausible solution. After the new technologies are identified, they must be evaluated

  9. Kradzieze samochodow w Polsce jako element ryzyka w ubezpieczeniach auto casco/Car Theft in Poland as a Part of the Risk in Auto Accident and Theft Insurance Approach to the Issue of Social Elites

    OpenAIRE

    Stanislaw Wieteska

    2015-01-01

    The problem of car theft has been observed for many years. The largest scale of this phenomenon occurred in the 1990’s. In this paper, the issue is discussed in social, ethical and economic aspects. We present the scale of the phenomenon of the theft of passenger vehicles in Poland in the years 2001–2012 in terms of the number of vehicles, type of stolen vehicles and the accident areas. In addition, we present the cause of theft and selected ways to protect cars from it. We also briefly discu...

  10. An Agent-Based Model for Optimization of Road Width and Public Transport Frequency

    Directory of Open Access Journals (Sweden)

    Mark E. Koryagin

    2015-04-01

    Full Text Available An urban passenger transportation problem is studied. Municipal authorities and passengers are regarded as participants in the passenger transportation system. The municipal authorities have to optimise road width and public transport frequency. The road consists of a dedicated bus lane and lanes for passenger cars. The car travel time depends on the number of road lanes and passengers’ choice of travel mode. The passengers’ goal is to minimize total travel costs, including time value. The passengers try to find the optimal ratio between public transport and cars. The conflict between municipal authorities and the passengers is described as a game theoretic model. The existence of Nash equilibrium in the model is proved. The numerical example shows the influence of the value of time and intensity of passenger flow on the equilibrium road width and public transport frequency.

  11. Passenger safety, health, and comfort: a review.

    Science.gov (United States)

    Rayman, R B

    1997-05-01

    Since the birth of aviation medicine approximately 80 yrs ago, practitioners and scientists have given their attention primarily to flight deck crew, cabin crew, and ground support personnel. However, in more recent years we have broadened our horizons to include the safety, health, and comfort of passengers flying commercial aircraft. This will be even more compelling as more passengers take to the air in larger aircraft and flying longer hours to more distant destinations. Further, we can expect to see more older passengers because people in many countries are living longer, healthier lives. The author first discusses the stresses imposed by ordinary commercial flight upon travelers such as airport tumult, barometric pressure changes, immobility, jet lag, noise/ vibration, and radiation. Medical considerations are next addressed describing inflight illness and medical care capability aboard U.S. air carriers. Passenger safety, cabin air quality, and the preventive medicine aspects of air travel are next reviewed in the context of passenger safety, health, and comfort. Recommendations are addressed to regulator agencies, airlines aircraft manufacturers, and the aerospace medicine community.

  12. 78 FR 74225 - Decision That Certain Nonconforming Motor Vehicles Are Eligible for Importation

    Science.gov (United States)

    2013-12-10

    ... Importation 1. Docket No. NHTSA-2013-0033 Nonconforming Vehicles: 1996 Chevrolet Impala Passenger Cars Substantially Similar U.S. Certified Vehicles: 1996 Chevrolet Impala Passenger Cars Notice of Petition Published...

  13. An improved car-following model accounting for the preceding car's taillight

    Science.gov (United States)

    Zhang, Jian; Tang, Tie-Qiao; Yu, Shao-Wei

    2018-02-01

    During the deceleration process, the preceding car's taillight may have influences on its following car's driving behavior. In this paper, we propose an extended car-following model with consideration of the preceding car's taillight. Two typical situations are used to simulate each car's movement and study the effects of the preceding car's taillight on the driving behavior. Meanwhile, sensitivity analysis of the model parameter is in detail discussed. The numerical results show that the proposed model can improve the stability of traffic flow and the traffic safety can be enhanced without a decrease of efficiency especially when cars pass through a signalized intersection.

  14. 49 CFR 1247.1 - Annual Report of Cars Loaded and Cars Terminated.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 9 2010-10-01 2010-10-01 false Annual Report of Cars Loaded and Cars Terminated... TRANSPORTATION BOARD, DEPARTMENT OF TRANSPORTATION (CONTINUED) ACCOUNTS, RECORDS AND REPORTS REPORT OF CARS LOADED AND CARS TERMINATED § 1247.1 Annual Report of Cars Loaded and Cars Terminated. Beginning with the...

  15. Passenger Perspectives in Railway Timetabling: A Literature Review

    DEFF Research Database (Denmark)

    Jensen, Jens Parbo; Nielsen, Otto Anker; Prato, Carlo Giacomo

    2016-01-01

    When looking at railway planning, a discrepancy exists between planners who focus on the train operations and publish fixed railway schedules, and passengers who look not only at the schedules but also at the entirety of their trip, from access to waiting to on-board travel and egress. Looking...... with fluctuating passenger demand. A key aspect is the robustness of railway timetables. Empirical evidence indicates that passengers give more importance to travel time certainty than travel time reductions, as passengers associate an inherent disutility with travel time uncertainty. This disutility may...... be broadly interpreted as an anxiety cost for the need for having contingency plans in case of disruptions, and may be looked at as the motivator for the need for delay-robust railway timetables. Interestingly, passenger-oriented optimisation studies considering robustness in railway planning typically limit...

  16. Methods to estimate railway capacity and passenger delays

    DEFF Research Database (Denmark)

    Landex, Alex

    that an evaluation of passenger delays obtained with simulation software (in this case RailSys) and the passenger delay model is comparable with the daily operation of the Copenhagen suburban railway network. Using a microscopic simulation model, the thesis demonstrates that it is possible to compare travel times...... of additional travel time. The differences between the different kinds of delay (train delays, passenger delays and scheduled waiting time) are illustrated through simple, but representative, case examples in CHAPTER 10. The examples demonstrate that 3rd generation passenger delay models are more realistic than...... depend on the given infrastructure and timetable and can result in longer travel times for trains and passengers. Furthermore, the thesis shows that the network effects can result in reduced capacity as some trains or train services can make it impossible to operate other planned/desired trains or train...

  17. New Algorithm for the Smoothing Speed Control of Induction Motor in Electric Car based on Self-Tuning Parameter PID-Fuzzy Logic

    Directory of Open Access Journals (Sweden)

    Dedid Cahya Happyanto

    2012-05-01

    Full Text Available Driving system of electric car for low speed has a performance of controller that is not easily set up on large span so it does not give a comfort to passengers. The study has been tested in the bumpy road conditions, by providing disturbances in the motor load, it is to describe the condition of the road. To improve the system performance, the speed and torque controller was applied using Field Oriented Control (FOC method. In this method, On-Line Proportional Integral Derivative Fuzzy Logic Controller (PID-FLC is used to give dynamic response to the change of speed and maximum torque on the electric car and this results the smooth movement on every change of car performance both in fast and slow movement when breaking action is taken. Optimization of membership functions in Fuzzy PID controller is required to obtain a new PID parameter values which is done in autotuning in any changes of the input or disturbance. PID parameter tuning in this case using the Ziegler-Nichols method based on frequency response. The mechanism is done by adjusting the PID parameters and the strengthening of the system output. The test results show that the controller Fuzzy Self-Tuning PID appropriate for Electric cars because they have a good response about 0.85% overshoot at to changes in speed and braking of electric cars.

  18. Heat transfer enhancement of a modularised thermoelectric power generator for passenger vehicles

    International Nuclear Information System (INIS)

    Li, Bo; Huang, Kuo; Yan, Yuying; Li, Yong; Twaha, Ssennoga; Zhu, Jie

    2017-01-01

    Highlights: •Shape-adapted thermoelectric module for highly compact heat recovery exchanger assembly. •Heat pipe-assisted heat transfer enhancement method for better power output. •Highest power output ratio to the total volume of heat recovery exchanger. •Cascaded thermoelectric system can be scaled and extended for various power output. •Self-clamping design of thermoelectric module can solve the thermomechanical imbalances. -- Abstract: Transport represents over a quarter of Europe's greenhouse gas emissions and is the leading cause of air pollution in cities. It has not seen the same gradual decline in emissions as other sectors. Recently, the thermoelectric power generation (TEG) technology emerges as an alternative solution to the emission reduction challenge in this area. In this paper, we present an innovative pathway to an improved heat supply into the concentric shape-adapted TEG modules, integrating the heat pipe technologies. It relies on a phase changing approach which enhances the heat flux through the TEG surface. In order to improve the heat transfer for higher efficiency, in our work, the heat pipes are configured in the radial direction of the exhaust streams. The analysis shows that the power output is adequate for the limited space under the chassis of the passenger car. Much effort can also be applied to obtain enhanced convective heat transfer by adjusting the heat pipes at the dual sides of the concentric TEG modules. Heat enhancement at the hot side of the TEG has an effective impact on the total power out of the TEG modules. However, such improvements can be offset by the adjustment made from the coolant side. Predictably, the whole temperature profile of TEG system is subject to the durability and operational limitations of each component. Furthermore, the results highlight the importance of heat transfer versus the TEG power generation under two possible configurations in the passenger car. The highest power output per

  19. Passive safety of passenger cars : a pilot-study into the development of a ranking list of passengers. On behalf of the Dutch Ministry of Transport and Public Works.

    NARCIS (Netherlands)

    Kampen, L.T.B. van

    1998-01-01

    This report is the English translation of IRRD 491574 (see C 11059). The key objective of this study was to investigate the feasibility of constructing a list of individual or grouped types of cars which could be ranked according to passive safety. A ranked listing was drawn up as based on accident

  20. Associations of individual, household and environmental characteristics with carbon dioxide emissions from motorised passenger travel.

    Science.gov (United States)

    Brand, Christian; Goodman, Anna; Rutter, Harry; Song, Yena; Ogilvie, David

    2013-04-01

    Carbon dioxide (CO 2 ) emissions from motorised travel are hypothesised to be associated with individual, household, spatial and other environmental factors. Little robust evidence exists on who contributes most (and least) to travel CO 2 and, in particular, the factors influencing commuting, business, shopping and social travel CO 2 . This paper examines whether and how demographic, socio-economic and other personal and environmental characteristics are associated with land-based passenger transport and associated CO 2 emissions. Primary data were collected from 3474 adults using a newly developed survey instrument in the iConnect study in the UK. The participants reported their past-week travel activity and vehicle characteristics from which CO 2 emissions were derived using an adapted travel emissions profiling method. Multivariable linear and logistic regression analyses were used to examine what characteristics predicted higher CO 2 emissions. CO 2 emissions from motorised travel were distributed highly unequally, with the top fifth of participants producing more than two fifth of emissions. Car travel dominated overall CO 2 emissions, making up 90% of the total. The strongest independent predictors of CO 2 emissions were owning at least one car, being in full-time employment and having a home-work distance of more than 10 km. Income, education and tenure were also strong univariable predictors of CO 2 emissions, but seemed to be further back on the causal pathway than having a car. Male gender, late-middle age, living in a rural area and having access to a bicycle also showed significant but weaker associations with emissions production. The findings may help inform the development of climate change mitigation policies for the transport sector. Targeting individuals and households with high car ownership, focussing on providing viable alternatives to commuting by car, and supporting planning and other policies that reduce commuting distances may provide an

  1. Associations of individual, household and environmental characteristics with carbon dioxide emissions from motorised passenger travel

    Science.gov (United States)

    Brand, Christian; Goodman, Anna; Rutter, Harry; Song, Yena; Ogilvie, David

    2013-01-01

    Carbon dioxide (CO2) emissions from motorised travel are hypothesised to be associated with individual, household, spatial and other environmental factors. Little robust evidence exists on who contributes most (and least) to travel CO2 and, in particular, the factors influencing commuting, business, shopping and social travel CO2. This paper examines whether and how demographic, socio-economic and other personal and environmental characteristics are associated with land-based passenger transport and associated CO2 emissions. Primary data were collected from 3474 adults using a newly developed survey instrument in the iConnect study in the UK. The participants reported their past-week travel activity and vehicle characteristics from which CO2 emissions were derived using an adapted travel emissions profiling method. Multivariable linear and logistic regression analyses were used to examine what characteristics predicted higher CO2 emissions. CO2 emissions from motorised travel were distributed highly unequally, with the top fifth of participants producing more than two fifth of emissions. Car travel dominated overall CO2 emissions, making up 90% of the total. The strongest independent predictors of CO2 emissions were owning at least one car, being in full-time employment and having a home-work distance of more than 10 km. Income, education and tenure were also strong univariable predictors of CO2 emissions, but seemed to be further back on the causal pathway than having a car. Male gender, late-middle age, living in a rural area and having access to a bicycle also showed significant but weaker associations with emissions production. The findings may help inform the development of climate change mitigation policies for the transport sector. Targeting individuals and households with high car ownership, focussing on providing viable alternatives to commuting by car, and supporting planning and other policies that reduce commuting distances may provide an equitable and

  2. 49 CFR 172.330 - Tank cars and multi-unit tank car tanks.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Tank cars and multi-unit tank car tanks. 172.330..., TRAINING REQUIREMENTS, AND SECURITY PLANS Marking § 172.330 Tank cars and multi-unit tank car tanks. (a... material— (1) In a tank car unless the following conditions are met: (i) The tank car must be marked on...

  3. 78 FR 57216 - General Motors, LLC, Receipt of Petition for Decision of Inconsequential Noncompliance

    Science.gov (United States)

    2013-09-17

    ... (MY) 2011 through 2013 Buick Regal and MY 2013 Chevrolet Malibu passenger cars may not fully comply... Chevrolet Malibu passenger cars manufactured from January 20, 2010 through September 18, 2012. III...

  4. An evaluation of the hybrid car technology for the Mexico Mega City

    Science.gov (United States)

    Jazcilevich, Aron D.; Reynoso, Agustin Garcia; Grutter, Michel; Delgado, Javier; Ayala, Ulises Diego; Lastra, Manuel Suarez; Zuk, Miriam; Oropeza, Rogelio Gonzalez; Lents, Jim; Davis, Nicole

    The introduction of hybrid electric vehicle (HEV) technology in the private car fleet of Mexico City is evaluated in terms of private costs, energy, public health and CO 2 emission benefits. In addition to constructing plausible scenarios for urban expansion, emission, car fleet, and fuel consumption for year 2026 and comparing them with a 2004 base case, a time series is built to obtain accumulated economic benefits. Experimental techniques were used to build a vehicle library for a car simulator that included a Prius 2002, chosen as the HEV technology representative for this work. The simulator is used to estimate the emissions and fuel consumption of the car fleet scenarios. In the context of an urban scenario for year 2026, a complex air quality model obtains the concentrations of criterion pollutants corresponding to these scenarios. Using a technology penetration model, the hybridized fleet starts unfolding in year 2009 reaching to 20% in 2026. In this year, the hybridized fleet resulted in reductions of about 10% of CO 2 emissions, and yielded reductions in daytime mean concentrations of up to 7% in ozone and 3.4% in PM 2.5 compared to the 2004 base case. These reductions are concentrated in the densely populated areas of Mexico City. By building a time series of costs and benefits it is shown that, depending on fuel prices and using a 5% return rate, positive accumulated benefits (CO 2 benefits + energy benefits + public health benefits - private costs) will start generating in year 2015 reaching between 2.8 and 4.5 billion US Dlls in 2026. Another modernized private fleet consisting exclusively of Tier I and II cars did not yield appreciable results, signaling that a change in private car technology towards HEV's is needed to obtain significant accumulated benefits.

  5. Fatal crashes of passenger vehicles before and after adding antilock braking systems.

    Science.gov (United States)

    Farmer, C M; Lund, A K; Trempel, R E; Braver, E R

    1997-11-01

    Fatal crash rates of passenger cars and vans were compared for the last model year before four-wheel antilock brakes were introduced and the first model year for which antilock brakes were standard equipment. Vehicles selected for analysis had no other significant design changes between the model years being compared, and the model years with and without antilocks were no more than two years apart. The overall fatal crash rates were similar for the two model years. However, the vehicles with antilocks were significantly more likely to be involved in crashes fatal to their own occupants, particularly single-vehicle crashes. Conversely, antilock vehicles were less likely to be involved in crashes fatal to occupants of other vehicles or nonoccupants (pedestrians, bicyclists). Overall, antilock brakes appear to have had little effect on fatal crash involvement. Further study is needed to better understand why fatality risk has increased for occupants of antilock vehicles.

  6. Consumption and efficiency of a passenger car with a hydrogen/oxygen PEFC based hybrid electric drivetrain

    Energy Technology Data Exchange (ETDEWEB)

    Buechi, F.N.; Dietrich, P.; Tsukada, A.; Koetz, R.; Freunberger, S.A. [Paul Scherrer Institut, Electrochemistry Laboratory, CH-5232 Villigen PSI (Switzerland); Paganelli, G.; Laurent, D.; Varenne, P.; Delfino, A.; Magne, P.A.; Walser, D.; Olsommer, D. [Conception et Developpement Michelin, Route Andre-Piller 30, CH-1762 Givisiez (Switzerland)

    2007-08-15

    The main factors for reducing the consumption of a vehicle are reduction of curb weight, air drag and increase in the drivetrain efficiency. Highly efficient drivetrains can be developed based on PEFC technology and curb weight may be limited by an innovative vehicle construction. In this paper, data on consumption and efficiency of a four-place passenger vehicle with a curb weight of 850 kg and an H{sub 2}/O{sub 2} fed PEFC/Supercap hybrid electric powertrain are presented. Hydrogen consumption in the New European Driving Cycle is 0.67 kg H{sub 2}/100 km, which corresponds to a gasoline equivalent consumption of 2.5 l/100 km. When including the energy needed to supply pure oxygen, the calculated consumption increases from 0.67 to 0.69-0.79 kg H{sub 2}/100 km, depending on the method of oxygen production. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

  7. Search for direct CP violating charge asymmetries in $K^\\pm\\to\\pi^\\pm\\pi^+\\pi^-$ and $K^\\pm\\to\\pi^\\pm\\pi^0\\pi^0$ decays

    CERN Document Server

    Batley, J Richard; Kalmus, George Ernest; Lazzeroni, C; Munday, D J; Slater, M W; Wotton, S A; Arcidiacono, R; Bocquet, G; Cabibbo, Nicola; Ceccucci, A; Cundy, Donald C; Falaleev, V; Fidecaro, Maria; Gatignon, L; Gonidec, A; Kubischta, Werner; Norton, A; Maier, A; Patel, M; Peters, A; Balev, S; Frabetti, P L; Goudzovski, E; Khristov, P Z; Kekelidze, V D; Kozhuharov, V; Litov, L; Madigozhin, D T; Marinova, E; Molokanova, N A; Polenkevich, I; Potrebenikov, Yu K; Stoynev, S; Zinchenko, A I; Monnier, E; Swallow, E; Winston, R; Rubin, P; Walker, A; Baldini, W; Cotta-Ramusino, A; Dalpiaz, P; Damiani, C; Fiorini, M; Gianoli, A; Martini, M; Petrucci, F; Savrié, M; Scarpa, M; Wahle, H; Bizzeti, A; Calvetti, M; Celeghini, E; Iacopini, E; Lenti, M; Martelli, F; Ruggiero, G; Veltri, M; Behler, M; Eppard, K; Kleinknecht, K; Marouelli, P; Masetti, L; Moosbrugger, U; Morales-Morales, C; Renk, B; Wache, M; Wanke, R; Winhart, A; Coward, D; Dabrowski, A; Fonseca-Martin, T; Shieh, M; Szleper, M; Velasco, M; Wood, M D; Anzivino, Giuseppina; Cenci, P; Imbergamo, E; Nappi, A; Pepé, M; Petrucci, M C; Piccini, M; Raggi, M; Valdata-Nappi, M; Cerri, C; Collazuol, G; Costantini, F; Di Lella, L; Doble, N; Fantechi, R; Fiorini, L; Giudici, S; Lamanna, G; Mannelli, I; Michetti, A; Pierazzini, G M; Sozzi, M; Bloch-Devaux, B; Cheshkov, C; Chèze, J B; De Beer, M; Derré, J; Marel, Gérard; Mazzucato, E; Peyaud, B; Vallage, B; Holder, M; Ziolkowski, M; Bifani, S; Biino, C; Cartiglia, N; Clemencic, M; Goy-Lopez, S; Marchetto, F; Dibon, Heinz; Jeitler, Manfred; Markytan, Manfred; Mikulec, I; Neuhofer, G; Widhalm, L

    2007-01-01

    A measurement of the direct CP violating charge asymmetries of the Dalitz plot linear slopes $A_g=(g^+-g^-)/(g^++g^-)$ in $K^\\pm\\to\\pi^\\pm\\pi^+\\pi^-$ and $K^\\pm\\to\\pi^\\pm\\pi^0\\pi^0$ decays by the NA48/2 experiment at CERN SPS is presented. A new technique of asymmetry measurement involving simultaneous $K^+$ and $K^-$ beams and a large data sample collected allowed a result of an unprecedented precision. The charge asymmetries were measured to be $A^c_g=(-1.5\\pm2.1)\\times10^{-4}$ with $3.11\\times 10^9$ $K^{\\pm}\\to\\pi^\\pm\\pi^+\\pi^-$ decays, and $A^n_g=(1.8\\pm1.8)\\times10^{-4}$ with $9.13\\times 10^7$ $K^{\\pm}\\to\\pi^\\pm\\pi^0\\pi^0$ decays. The precision of the results is limited mainly by the size of the data sample.

  8. Rescheduling of Railway Rolling Stock with Dynamic Passenger Flows

    NARCIS (Netherlands)

    L.G. Kroon (Leo); G. Maróti (Gábor); L.K. Nielsen (Lars Kjaer)

    2010-01-01

    textabstractTraditional rolling stock rescheduling applications either treat passengers as static objects whose influence on the system is unchanged in a disrupted situation, or they treat passenger behavior as a given input. In case of disruptions however, we may expect the flow of passengers to

  9. 49 CFR 541.5 - Requirements for passenger motor vehicles.

    Science.gov (United States)

    2010-10-01

    ... TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR VEHICLE THEFT PREVENTION STANDARD § 541.5 Requirements for passenger motor vehicles. (a) Each passenger motor vehicle subject to... 49 Transportation 6 2010-10-01 2010-10-01 false Requirements for passenger motor vehicles. 541.5...

  10. 36 CFR 1005.4 - Commercial passenger-carrying motor vehicles.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Commercial passenger-carrying motor vehicles. 1005.4 Section 1005.4 Parks, Forests, and Public Property PRESIDIO TRUST COMMERCIAL AND PRIVATE OPERATIONS § 1005.4 Commercial passenger-carrying motor vehicles. Passenger-carrying motor...

  11. 46 CFR 71.75-5 - Passenger Ship Safety Certificate.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Passenger Ship Safety Certificate. 71.75-5 Section 71.75-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS INSPECTION AND... Passenger Ship Safety Certificate. (a) All vessels on an international voyage are required to have a...

  12. CERN CAR CLUB

    CERN Multimedia

    Automobile club

    2009-01-01

    You are cordially invited to the next General Assembly of the CERN Car Club Tuesday 12 January 2010 at 5:45pm Bldg. 593 / room 11 As the end of 2009 is approaching, it is time to think about renewing your subscription. Therefore next time you are on the CERN-Meyrin site or at the Post Office counter don’t forget to fill in the payment slip to continue to be a part of our large family. The fee remains unchanged: 50 CHF. For those of you who are regular users of our equipment and who know of all the advantages that the club is in a position to offer, it seems pointless to give details, we are sure that many of you have made use of them and are satisfied. We remind you everyone working on CERN site is entitled to become a member of our club, this includes industrial support personnel and staff of companies which have a contract with CERN. If you are not yet a member, come and visit us! We will be happy to welcome you and show you the facilities, or you can visit our web site. The use of the club&...

  13. Mortality of German travellers on passenger vessels.

    Science.gov (United States)

    Oldenburg, Marcus; Herzog, Jan; Püschel, Klaus; Harth, Volker

    2016-01-01

    In the past two decades, more and more Germans decided to spend their holidays on a passenger vessel. This study examined the frequencies and causes of deaths of German travellers aboard passenger vessels of all flags. The shipboard deaths of all German travellers within the time period from 1998 to 2008 were counted using the German civil central register in Berlin. The available documentation in this register provides information on frequencies, circumstances and causes of deaths on ships. In the above-mentioned period of time, the total cohort of German travellers on cruise ships is estimated to be 5.97 million persons. During the 11-year examination period, 135 shipboard deaths of German passengers [102 males (75.6%) and 33 females (24.4%)] were recorded. Out of these travellers, 110 died on cruise ships. When considering only the passengers on cruise ships (without those on ferries) an average crude mortality rate of 1.8 per 100,000 German passengers was calculated. The crude mortality rate of shipboard death for males and females was 2.5 and 0.8 per 100,000 German passengers with a mean age of 71.2 years [standard deviation (SD) 16.0 years] and 73.3 years (SD 16.0 years), respectively. Significantly, more deceased travellers older than 70 years were observed on traditional cruise ships and resort vessels than on passenger ferries (P = 0.001). The causes of death were documented in 85 cases (63.0%). Out of these documented deaths, 82 (96.5%) cases were regarded to be natural causes (particularly circulatory diseases) and 3 (3.5%) as unnatural causes (twice drowning and once an accidental fall). In spite of the large proportion of unknown causes of death, this study argues for a high significance of internal causes of deaths among German passengers. Thus, ship's doctors-particularly those on traditional cruise ships-should be well experienced in internal and geriatric medicines. © The Author 2016. Published by Oxford University Press on behalf of

  14. Real-time passenger counting by active linear cameras

    Science.gov (United States)

    Khoudour, Louahdi; Duvieubourg, Luc; Deparis, Jean-Pierre

    1996-03-01

    The companies operating subways are very much concerned with counting the passengers traveling through their transport systems. One of the most widely used systems for counting passengers consists of a mechanical gate equipped with a counter. However, such simple systems are not able to count passengers jumping above the gates. Moreover, passengers carrying large luggage or bags may meet some difficulties when going through such gates. The ideal solution is a contact-free counting system that would bring more comfort of use for the passengers. For these reasons, we propose to use a video processing system instead of these mechanical gates. The optical sensors discussed in this paper offer several advantages including well defined detection areas, fast response time and reliable counting capability. A new technology has been developed and tested, based on linear cameras. Preliminary results show that this system is very efficient when the passengers crossing the optical gate are well separated. In other cases, such as in compact crowd conditions, reasonable accuracy has been demonstrated. These results are illustrated by means of a number of sequences shot in field conditions. It is our belief that more precise measurements could be achieved, in the case of compact crowd, by other algorithms and acquisition techniques of the line images that we are presently developing.

  15. 75 FR 57549 - Fisker Automotive; Grant of Application for Temporary Exemption From Advanced Air Bag...

    Science.gov (United States)

    2010-09-21

    ... requirements submitted by a manufacturer of a plug-in hybrid electric car. The basis of the petition was... upgraded the requirements for air bags in passenger cars and light trucks, requiring what are commonly... completely new passenger car model. Design and development of the Karma began in late 2007. The Karma is...

  16. 78 FR 9107 - Petition for Waiver of Compliance

    Science.gov (United States)

    2013-02-07

    ... Glazing Standards-- Locomotives, Passenger Cars and Cabooses). FRA assigned the petition Docket Number FRA... requirements set forth in 49 CFR part 223 for one locomotive, one passenger car, and three cabooses--all of... electric 660 HP, was built in 1943 as U.S. Navy 7135. Passenger Coach KJR 1154 was built in the 1920s for...

  17. 14 CFR 135.113 - Passenger occupancy of pilot seat.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Passenger occupancy of pilot seat. 135.113... Operations § 135.113 Passenger occupancy of pilot seat. No certificate holder may operate an aircraft type certificated after October 15, 1971, that has a passenger seating configuration, excluding any pilot seat, of...

  18. Principles of Logistics Applied to Railway Passenger Transport

    Directory of Open Access Journals (Sweden)

    Vojtek Martin

    2017-01-01

    Full Text Available Main challenge of logistics is delivering right assortment of products in exact amount, to exact place, in exact time, ecologically and for exact price. Logistics deals with freight transport but when the word ‘products’ is changed to ‘passengers’, then many principles can be applied to passenger transport. Railway passenger transport is the key part of passenger transport system, so it is necessary to optimize it on logistics philosophy at first.

  19. Positive and negative spillover effects from electric car purchase to car use

    OpenAIRE

    Kløckner, Christian; Nayum, Alim; Mehmetoglu, Mehmet

    2013-01-01

    This study reports the results of two online surveys conducted on buyers of conventional combustion engine cars compared to those of electric vehicles in Norway. The results show that electric cars are generally purchased as additional cars, do not contribute to a decrease in annual mileage if the old car is not substituted, and that electric car buyers use the car more often for their everyday mobility. Psychological determinants derived from the theory of planned behavior and the norm-activ...

  20. A train dispatching model based on fuzzy passenger demand forecasting during holidays

    Directory of Open Access Journals (Sweden)

    Fei Dou Dou

    2013-03-01

    Full Text Available Abstract: Purpose: The train dispatching is a crucial issue in the train operation adjustment when passenger flow outbursts. During holidays, the train dispatching is to meet passenger demand to the greatest extent, and ensure safety, speediness and punctuality of the train operation. In this paper, a fuzzy passenger demand forecasting model is put up, then a train dispatching optimization model is established based on passenger demand so as to evacuate stranded passengers effectively during holidays. Design/methodology/approach: First, the complex features and regularity of passenger flow during holidays are analyzed, and then a fuzzy passenger demand forecasting model is put forward based on the fuzzy set theory and time series theory. Next, the bi-objective of the train dispatching optimization model is to minimize the total operation cost of the train dispatching and unserved passenger volume during holidays. Finally, the validity of this model is illustrated with a case concerned with the Beijing-Shanghai high-speed railway in China. Findings: The case study shows that the fuzzy passenger demand forecasting model can predict outcomes more precisely than ARIMA model. Thus train dispatching optimization plan proves that a small number of trains are able to serve unserved passengers reasonably and effectively. Originality/value: On the basis of the passenger demand predictive values, the train dispatching optimization model is established, which enables train dispatching to meet passenger demand in condition that passenger flow outbursts, so as to maximize passenger demand by offering the optimal operation plan.

  1. PAH, BTEX, carbonyl compound, black-carbon, NO2 and ultrafine particle dynamometer bench emissions for Euro 4 and Euro 5 diesel and gasoline passenger cars

    Science.gov (United States)

    Louis, Cédric; Liu, Yao; Tassel, Patrick; Perret, Pascal; Chaumond, Agnès; André, Michel

    2016-09-01

    Although implementing Diesel particulate filters (DPF) and other novel aftertreatment technologies makes it possible to achieve significant reductions in particle mass emissions, it may induce the release of ultrafine particles and emissions of many other unregulated compounds. This paper focuses on (i) ultrafine particles, black carbon, BTEX, PAH, carbonyl compounds, and NO2 emissions from Euro 4 and Euro 5 Diesel and gasoline passenger cars, (ii) the influence of driving conditions (e.g., cold start, urban, rural and motorway conditions), and (iii) the impact of additive and catalysed DPF devices on vehicle emissions. Chassis dynamometer tests were conducted on four Euro 5 vehicles and two Euro 4 vehicles: gasoline vehicles with and without direct injection system and Diesel vehicles equipped with additive and catalysed particulate filters. The results showed that compared to hot-start cycles, cold-start urban cycles increased all pollutant emissions by a factor of two. The sole exception was NO2, which was reduced by a factor of 1.3-6. Particulate and black carbon emissions from the gasoline engines were significantly higher than those from the Diesel engines equipped with DPF. Moreover, the catalysed DPF emitted about 3-10 times more carbonyl compounds and particles than additive DPF, respectively, during urban driving cycles, while the additive DPF vehicles emitted 2 and 5 times more BTEX and carbonyl compounds during motorway driving cycles. Regarding particle number distribution, the motorway driving cycle induced the emission of particles smaller in diameter (mode at 15 nm) than the urban cold-start cycle (mode at 80-100 nm). The results showed a clear positive correlation between particle, black carbon, and BTEX emissions, and a negative correlation between particles and NO2.

  2. Investigation of a methanol reformer concept considering the particular impact of dynamics and long-term stability for use in a fuel-cell-powered passenger car

    Science.gov (United States)

    Peters, R.; Düsterwald, H. G.; Höhlein, B.

    A methanol reformer concept including a reformer, a catalytic burner, a gas cleaning unit, a PEMFC and an electric motor for use in fuel-cell-powered passenger cars was investigated. Special emphasis was placed on the dynamics and the long-term stability of the reformer. Experiments on a laboratory scale were performed in a methanol steam reformer consisting of four different reactor tubes, which were separately balanced. Due to the endothermy of the steam reforming reaction of methanol, a sharp drop in the reaction temperature of about 50 K occurs at the beginning of the catalyst bed. This agrees well with the high catalytic activity at the entrance of the catalyst bed. Forty-five percent of the methanol was converted within the first 10 cm of the catalyst bed where 12.6 g of the CuO/ZnO catalyst was located. Furthermore, CO formation during methanol steam reforming strongly depends on methanol conversion. Long-term measurements for more than 700 h show that the active reaction zone moved through the catalyst bed. Calculations, on the basis of these experiments, revealed that 63 g of reforming catalyst was necessary for mobile PEMFC applications, in this case for 400 W el at a system efficiency of 42% and a theoretical specific hydrogen production of 5.2 m 3n/(h kg Cat). This amount of catalyst was assumed to maintain a hydrogen production of at least 80% of the original amount over an operating range of 3864 h. Cycled start-up and shut-down processes of the methanol steam reformer under nitrogen and hydrogen atmospheres did not harm the catalytic activity. The simulation of the breakdown of the heating system, in which a liquid water/methanol mixture was in close contact with the catalyst, did not reveal any deactivation of the catalytic activity.

  3. Social prejudice hindering proper use of car safety seats.

    Science.gov (United States)

    Kanburoglu, Mehmet Kenan; Cizmeci, Mehmet Nevzat; Akelma, Ahmet Zulfikar; Orun, Emel; Yesilyurt, Kubra; Tatli, Mustafa Mansur

    2013-12-01

    The compliance of parents with child passenger safety (CPS) has been mainly explained by their level of knowledge. Social, ethnic and cultural factors have not been investigated in detail. This study investigated the rate of compliance of parents with CPS guidelines, as well as the factors hindering it. Parents of infants aged 2-10 days were enrolled. The proportions of families obtaining a car safety seat (CSS; 57%) and complying with CPS recommendations (2%) were very low. Most of the parents thought CSS were harmful for infants (mother, 57%; father, 63%), despite having already purchased one. Parents believed their children to be too small to use CSS and cannot sit in CSS because they should lie flat on their backs at all times. These prejudices may be due to the social and cultural circumstances specific to Turkey, or corresponding findings may be found in countries with similar socioeconomic status. © 2013 The Authors. Pediatrics International © 2013 Japan Pediatric Society.

  4. Observation of $C\\!P$ violation in $B^\\pm \\to D K^\\pm$ decays

    CERN Document Server

    Aaij, R; Adeva, B; Adinolfi, M; Adrover, C; Affolder, A; Ajaltouni, Z; Albrecht, J; Alessio, F; Alexander, M; Ali, S; Alkhazov, G; Alvarez Cartelle, P; Alves Jr, A A; Amato, S; Amhis, Y; Anderson, J; Appleby, R B; Aquines Gutierrez, O; Archilli, F; Artamonov, A; Artuso, M; Aslanides, E; Auriemma, G; Bachmann, S; Back, J J; Balagura, V; Baldini, W; Barlow, R J; Barschel, C; Barsuk, S; Barter, W; Bates, A; Bauer, C; Bauer, Th; Bay, A; Bediaga, I; Belogurov, S; Belous, K; Belyaev, I; Ben-Haim, E; Benayoun, M; Bencivenni, G; Benson, S; Benton, J; Bernet, R; Bettler, M-O; van Beuzekom, M; Bien, A; Bifani, S; Bird, T; Bizzeti, A; Bjørnstad, P M; Blake, T; Blanc, F; Blanks, C; Blouw, J; Blusk, S; Bobrov, A; Bocci, V; Bondar, A; Bondar, N; Bonivento, W; Borghi, S; Borgia, A; Bowcock, T J V; Bozzi, C; Brambach, T; van den Brand, J; Bressieux, J; Brett, D; Britsch, M; Britton, T; Brook, N H; Brown, H; Büchler-Germann, A; Burducea, I; Bursche, A; Buytaert, J; Cadeddu, S; Callot, O; Calvi, M; Calvo Gomez, M; Camboni, A; Campana, P; Carbone, A; Carboni, G; Cardinale, R; Cardini, A; Carson, L; Carvalho Akiba, K; Casse, G; Cattaneo, M; Cauet, Ch; Charles, M; Charpentier, Ph; Chiapolini, N; Ciba, K; Cid Vidal, X; Ciezarek, G; Clarke, P E L; Clemencic, M; Cliff, H V; Closier, J; Coca, C; Coco, V; Cogan, J; Collins, P; Comerma-Montells, A; Contu, A; Cook, A; Coombes, M; Corti, G; Couturier, B; Cowan, G A; Currie, R; D'Ambrosio, C; David, P; David, P N Y; De Bonis, I; De Bruyn, K; De Capua, S; De Cian, M; De Miranda, J M; De Paula, L; De Simone, P; Decamp, D; Deckenhoff, M; Degaudenzi, H; Del Buono, L; Deplano, C; Derkach, D; Deschamps, O; Dettori, F; Dickens, J; Dijkstra, H; Diniz Batista, P; Domingo Bonal, F; Donleavy, S; Dordei, F; Dosil Suárez, A; Dossett, D; Dovbnya, A; Dupertuis, F; Dzhelyadin, R; Dziurda, A; Easo, S; Egede, U; Egorychev, V; Eidelman, S; van Eijk, D; Eisele, F; Eisenhardt, S; Ekelhof, R; Eklund, L; Elsasser, Ch; Elsby, D; Esperante Pereira, D; Falabella, A; Färber, C; Fardell, G; Farinelli, C; Farry, S; Fave, V; Fernandez Albor, V; Ferro-Luzzi, M; Filippov, S; Fitzpatrick, C; Fontana, M; Fontanelli, F; Forty, R; Francisco, O; Frank, M; Frei, C; Frosini, M; Furcas, S; Gallas Torreira, A; Galli, D; Gandelman, M; Gandini, P; Gao, Y; Garnier, J-C; Garofoli, J; Garra Tico, J; Garrido, L; Gascon, D; Gaspar, C; Gauld, R; Gauvin, N; Gersabeck, M; Gershon, T; Ghez, Ph; Gibson, V; Gligorov, V V; Göbel, C; Golubkov, D; Golutvin, A; Gomes, A; Gordon, H; Grabalosa Gándara, M; Graciani Diaz, R; Granado Cardoso, L A; Graugés, E; Graziani, G; Grecu, A; Greening, E; Gregson, S; Gui, B; Gushchin, E; Guz, Yu; Gys, T; Hadjivasiliou, C; Haefeli, G; Haen, C; Haines, S C; Hampson, T; Hansmann-Menzemer, S; Harji, R; Harnew, N; Harrison, J; Harrison, P F; Hartmann, T; He, J; Heijne, V; Hennessy, K; Henrard, P; Hernando Morata, J A; van Herwijnen, E; Hicks, E; Holubyev, K; Hopchev, P; Hulsbergen, W; Hunt, P; Huse, T; Huston, R S; Hutchcroft, D; Hynds, D; Iakovenko, V; Ilten, P; Imong, J; Jacobsson, R; Jaeger, A; Jahjah Hussein, M; Jans, E; Jansen, F; Jaton, P; Jean-Marie, B; Jing, F; John, M; Johnson, D; Jones, C R; Jost, B; Kaballo, M; Kandybei, S; Karacson, M; Karbach, T M; Keaveney, J; Kenyon, I R; Kerzel, U; Ketel, T; Keune, A; Khanji, B; Kim, Y M; Knecht, M; Koopman, R F; Koppenburg, P; Korolev, M; Kozlinskiy, A; Kravchuk, L; Kreplin, K; Kreps, M; Krocker, G; Krokovny, P; Kruse, F; Kruzelecki, K; Kucharczyk, M; Kudryavtsev, V; Kvaratskheliya, T; La Thi, V N; Lacarrere, D; Lafferty, G; Lai, A; Lambert, D; Lambert, R W; Lanciotti, E; Lanfranchi, G; Langenbruch, C; Latham, T; Lazzeroni, C; Le Gac, R; van Leerdam, J; Lees, J-P; Lefèvre, R; Leflat, A; Lefrançois, J; Leroy, O; Lesiak, T; Li, L; Li Gioi, L; Lieng, M; Liles, M; Lindner, R; Linn, C; Liu, B; Liu, G; von Loeben, J; Lopes, J H; Lopez Asamar, E; Lopez-March, N; Lu, H; Luisier, J; Mac Raighne, A; Machefert, F; Machikhiliyan, I V; Maciuc, F; Maev, O; Magnin, J; Malde, S; Mamunur, R M D; Manca, G; Mancinelli, G; Mangiafave, N; Marconi, U; Märki, R; Marks, J; Martellotti, G; Martens, A; Martin, L; Martín Sánchez, A; Martinelli, M; Martinez Santos, D; Massafferri, A; Mathe, Z; Matteuzzi, C; Matveev, M; Maurice, E; Maynard, B; Mazurov, A; McGregor, G; McNulty, R; Meissner, M; Merk, M; Merkel, J; Miglioranzi, S; Milanes, D A; Minard, M-N; Molina Rodriguez, J; Monteil, S; Moran, D; Morawski, P; Mountain, R; Mous, I; Muheim, F; Müller, K; Muresan, R; Muryn, B; Muster, B; Mylroie-Smith, J; Naik, P; Nakada, T; Nandakumar, R; Nasteva, I; Needham, M; Neufeld, N; Nguyen, A D; Nguyen-Mau, C; Nicol, M; Niess, V; Nikitin, N; Nikodem, T; Nomerotski, A; Novoselov, A; Oblakowska-Mucha, A; Obraztsov, V; Oggero, S; Ogilvy, S; Okhrimenko, O; Oldeman, R; Orlandea, M; Otalora Goicochea, J M; Owen, P; Pal, B K; Palacios, J; Palano, A; Palutan, M; Panman, J; Papanestis, A; Pappagallo, M; Parkes, C; Parkinson, C J; Passaleva, G; Patel, G D; Patel, M; Paterson, S K; Patrick, G N; Patrignani, C; Pavel-Nicorescu, C; Pazos Alvarez, A; Pellegrino, A; Penso, G; Pepe Altarelli, M; Perazzini, S; Perego, D L; Perez Trigo, E; Pérez-Calero Yzquierdo, A; Perret, P; Perrin-Terrin, M; Pessina, G; Petrolini, A; Phan, A; Picatoste Olloqui, E; Pie Valls, B; Pietrzyk, B; Pilař, T; Pinci, D; Plackett, R; Playfer, S; Plo Casasus, M; Polok, G; Poluektov, A; Polycarpo, E; Popov, D; Popovici, B; Potterat, C; Powell, A; Prisciandaro, J; Pugatch, V; Puig Navarro, A; Qian, W; Rademacker, J H; Rakotomiaramanana, B; Rangel, M S; Raniuk, I; Raven, G; Redford, S; Reid, M M; dos Reis, A C; Ricciardi, S; Richards, A; Rinnert, K; Roa Romero, D A; Robbe, P; Rodrigues, E; Rodrigues, F; Rodriguez Perez, P; Rogers, G J; Roiser, S; Romanovsky, V; Rosello, M; Rouvinet, J; Ruf, T; Ruiz, H; Sabatino, G; Saborido Silva, J J; Sagidova, N; Sail, P; Saitta, B; Salzmann, C; Sannino, M; Santacesaria, R; Santamarina Rios, C; Santinelli, R; Santovetti, E; Sapunov, M; Sarti, A; Satriano, C; Satta, A; Savrie, M; Savrina, D; Schaack, P; Schiller, M; Schindler, H; Schleich, S; Schlupp, M; Schmelling, M; Schmidt, B; Schneider, O; Schopper, A; Schune, M-H; Schwemmer, R; Sciascia, B; Sciubba, A; Seco, M; Semennikov, A; Senderowska, K; Sepp, I; Serra, N; Serrano, J; Seyfert, P; Shapkin, M; Shapoval, I; Shatalov, P; Shcheglov, Y; Shears, T; Shekhtman, L; Shevchenko, O; Shevchenko, V; Shires, A; Silva Coutinho, R; Skwarnicki, T; Smith, N A; Smith, E; Sobczak, K; Soler, F J P; Solomin, A; Soomro, F; Souza De Paula, B; Spaan, B; Sparkes, A; Spradlin, P; Stagni, F; Stahl, S; Steinkamp, O; Stoica, S; Stone, S; Storaci, B; Straticiuc, M; Straumann, U; Subbiah, V K; Swientek, S; Szczekowski, M; Szczypka, P; Szumlak, T; T'Jampens, S; Teodorescu, E; Teubert, F; Thomas, C; Thomas, E; van Tilburg, J; Tisserand, V; Tobin, M; Tolk, S; Topp-Joergensen, S; Torr, N; Tournefier, E; Tourneur, S; Tran, M T; Tsaregorodtsev, A; Tuning, N; Ubeda Garcia, M; Ukleja, A; Uwer, U; Vagnoni, V; Valenti, G; Vazquez Gomez, R; Vazquez Regueiro, P; Vecchi, S; Velthuis, J J; Veltri, M; Viaud, B; Videau, I; Vieira, D; Vilasis-Cardona, X; Visniakov, J; Vollhardt, A; Volyanskyy, D; Voong, D; Vorobyev, A; Vorobyev, V; Voss, H; Waldi, R; Wandernoth, S; Wang, J; Ward, D R; Watson, N K; Webber, A D; Websdale, D; Whitehead, M; Wiedner, D; Wiggers, L; Wilkinson, G; Williams, M P; Williams, M; Wilson, F F; Wishahi, J; Witek, M; Witzeling, W; Wotton, S A; Wyllie, K; Xie, Y; Xing, F; Xing, Z; Yang, Z; Young, R; Yushchenko, O; Zangoli, M; Zavertyaev, M; Zhang, F; Zhang, L; Zhang, W C; Zhang, Y; Zhelezov, A; Zhong, L; Zvyagin, A

    2012-01-01

    An analysis of $B^{\\pm}\\to DK^{\\pm}$ and $B^{\\pm}\\to D\\pi^{\\pm}$ decays is presented where the $D$ meson is reconstructed in the two-body final states:$K^{\\pm}\\pi^{\\mp}$, $K^+K^-$, $\\pi^+\\pi^-$ and $\\pi^{\\pm}K^{\\mp}$. Using $1.0{\\rm \\,fb}^{-1}$ of LHCb data, measurements of several observables are made including the first observation of the suppressed mode $B^{\\pm}\\to[\\pi^{\\pm}K^{\\mp}]_DK^{\\pm}$. $C\\!P$ violation in $B^{\\pm}\\to DK^{\\pm}$ decays is observed with $5.8\\,\\sigma$ significance.

  5. Observation of photon polarization in $B^\\pm \\to K^\\pm\\pi^\\mp\\pi^\\pm\\gamma$ decays

    CERN Multimedia

    Veneziano, G

    2014-01-01

    A study of the flavor-changing neutral current radiative $B^{\\pm} \\to K^{\\pm}\\pi^{\\mp}\\pi^{\\pm}\\gamma$ decays performed using data collected in proton-proton collisions with the LHCb detector at $7$ and $8\\,$TeV center-of-mass energies is presented. In this sample, corresponding to an integrated luminosity of $3\\,\\text{fb}^{-1}$, nearly $14\\,000$ signal events are reconstructed and selected, containing all possible intermediate resonances with a $K^{\\pm}\\pi^{\\mp}\\pi^{\\pm}$ final state in the $[1.1, 1.9]$\\,GeV/$c^{2}$ mass range. The distribution of the angle of the photon direction with respect to the plane defined by the final-state hadrons in their rest frame is studied in intervals of $K^{\\pm}\\pi^{\\mp}\\pi^{\\pm}$ mass and the asymmetry between the number of signal events found on each side of the plane is obtained. The first direct observation of the photon polarization in the $b \\to s\\gamma$ transition is reported with a significance of $5.2\\,\\sigma$.

  6. Wintertime indoor air levels of PM10, PM2.5 and PM1 at public places and their contributions to TSP.

    Science.gov (United States)

    Liu, Yangsheng; Chen, Rui; Shen, Xingxing; Mao, Xiaoling

    2004-04-01

    From 26 October 2002 to 8 March 2003, particulate matter (PM) concentrations (total suspended particles [TSP], PM10, PM2.5 and PM1) were measured at 49 public places representing different environments in the urban area of Beijing. The objectives of this study were (1) to characterize the indoor PM concentrations in public places, (2) to evaluate the potential indoor sources and (3) to investigate the contribution of PM10 to TSP and the contributions of PM2.5 and PM1 to PM10. Additionally, The indoor and outdoor particle concentrations in the same type of indoor environment were employed to investigate the I/O level, and comparison was made between I/O levels in different types of indoor environment. Construction activities and traffic condition were the major outdoor sources to influence the indoor particle levels. The contribution of PM10 to TSP was even up to 68.8%, while the contributions of PM2.5 and PM1 to PM10 were not as much as that of PM10 to TSP.

  7. Electric Car Special

    Energy Technology Data Exchange (ETDEWEB)

    Zoethout, T.; Belin, H.; Verwijs, H.; Nicola, S.; De Saint Jacob, Y.; Gatermann, R.

    2009-09-15

    In six articles, two columns and two interviews a part of this issue is dedicated to electric car developments: about winners and losers in the electric car race; a unique business model to rolling out the electric car by the electric battery company Better Place and the automobile industry Renault Nissan; interview with entrepreneur Shai Agassi of the Indian company Better Place; the development of electric cars in Germany; interview with Jean-Jacques Chanaron, an economist specialising in innovation management and a firm believer in electric cars; start of mass production of electric vehicles at the Japanese Nissan automobile industry; the constraints in Sweden in developing fuel-efficient automobiles; plans for 1 million electric or hybrid cars by 2025 in the Netherlands.

  8. Delay Management with Re-Routing of Passengers

    NARCIS (Netherlands)

    T.A.B. Dollevoet (Twan); D. Huisman (Dennis); M.E. Schmidt (Marie); A. Schöbel (Anita)

    2010-01-01

    textabstractThe question of delay management is whether trains should wait for a delayed feeder train or should depart on time. In classical delay management models passengers always take their originally planned route. In this paper, we propose a model where re-routing of passengers is

  9. Salmonella outbreak among railway and airline passengers.

    Science.gov (United States)

    Hatakka, M

    1992-01-01

    A widespread outbreak by Salmonella infantis, infecting a total of 226 people, occurred in Finland at the beginning of August 1986. Of those infected, 107 were railway passengers, 91 were airline passengers and 28 were employed in a food processing establishment. The outbreak among the railway passengers was caused by egg sandwiches, the airline passengers were infected by a meal served on board and the catering employees by the breakfast served in the establishment. The outbreak was caused by food prepared in the establishment's kitchen. The employees' breakfasts had probably been contaminated by an employee who was a symptom-free Salmonella infantis carrier, and a number of the employees subsequently became infected, leading to widespread contamination of the food prepared in the establishment. The spread of the outbreak was further influenced by a heatwave at the time and by shortcomings in the cold storage facilities. The kitchen's hygiene supervision and the quality control of its output were reorganized after the outbreak.

  10. The ironies of vehicle feedback in car design.

    Science.gov (United States)

    Walker, Guy H; Stanton, Neville A; Young, Mark S

    2006-02-10

    Car drivers show an acute sensitivity towards vehicle feedback, with most normal drivers able to detect 'the difference in vehicle feel of a medium-size saloon car with and without a fairly heavy passenger in the rear seat' (Joy and Hartley 1953-54). The irony is that this level of sensitivity stands in contrast to the significant changes in vehicle 'feel' accompanying modern trends in automotive design, such as drive-by-wire and increased automation. The aim of this paper is to move the debate from the anecdotal to the scientific level. This is achieved by using the Brunel University driving simulator to replicate some of these trends and changes by presenting (or removing) different forms of non-visual vehicle feedback, and measuring resultant driver situational awareness (SA) using a probe-recall method. The findings confirm that vehicle feedback plays a key role in coupling the driver to the dynamics of their en