Effects of Roads on Amphibian Populations

DEFF Research Database (Denmark)

Hels, T.

is the result of my three year PhD study at the National Environmental Research Institute, Kalø, and University of Copenhagen. Funded by NERI, the Danish Research Academy, and the Danish Road Directorate, it has dealt mainly with the effects of traffic and roads on amphibian populations. The Spadefoot toad...... of Spadefoot toads (Pelobates fuscus Laur.) II The effect of road kills on amphibian populations III Simulating viability of a Spadefoot toad (P. fuscus) metapopulation in a landscape fragmented by a road The manuscripts are preceded by a synopsis which sums up the work and puts it into a broader perspective......, Johan Elmberg, Andreas Seiler, and Per Sjögren-Gulve, for sharing your knowledge and enthusiasm for science with me. Constructive ideas, different approaches, and elaborate discussions are crucial parts of any scientific process: I thank Lenore Fahrig for dedicated and original teaching and discussions...

Trajectory of a road vehicle during road maintenance

OpenAIRE

Stachová Darina

2017-01-01

Consider a vehicle moving on a road whose usage over time creates an uneven surface on the road. Road unevenness that we encounter on surface communications often arises as a consequence of dynamical effects of moving vehicles, of weather changes, and due to road construction works. This article concerns with mathematical modeling of the trajectory of a road vehicle moving on such a surface during the course of road maintenance.

30 CFR 816.150 - Roads: general.

Science.gov (United States)

2010-07-01

... altering the normal flow of water in streambeds or drainage channels; (6) Prevent or control damage to... part of any road shall be located in the channel of an intermittent or perennial stream unless... 816.57 of this chapter. (2) Roads shall be located to minimize downstream sedimentation and flooding...

30 CFR 817.150 - Roads: General.

Science.gov (United States)

2010-07-01

... altering the normal flow of water in streambeds or drainage channels; (6) Prevent or control damage to... part of any road shall be located in the channel of an intermittent or perennial stream unless... 817.57 of this chapter. (2) Roads shall be located to minimize downstream sedimentation and flooding...

Environmental exposure of road borders to zinc

International Nuclear Information System (INIS)

Blok, J.

2005-01-01

The emissions of zinc along roads originating from tyre wear, corrosion of safety fence and other traffic-related sources have been quantified and validated by measured long-term loads in road run-off and airborne solids (drift) for 29 published case studies. The distribution pattern over the road border at various distances from the edge of the paved surface is assessed on the basis of 38 published case studies with measured concentrations in soil. For the impact assessment, the road border is differentiated into a zone that is part of the 'technosphere' and the 'target zone' beyond that technosphere that can be considered as part of the receiving environment. The 'technosphere' of the road includes the central reservation, the hard and the soft shoulder or, if one or both shoulders are not present, the so-called obstacle 'free zone' that is defined by road engineers. Pollution within the technosphere may require appropriate management of solid disposal and isolation from groundwater to prevent further distribution of pollutants to the environment. In the target zone along regional roads, the zinc load is about 4 mg/m 2 year and this is of the same order of magnitude as that of atmospheric deposition in areas beyond the influence of roads (background). In the target zone along highways, the zinc load is increased in comparison to the background deposition. The average load of about 38 mg/m 2 year is similar to that in fertilised agricultural land. Because most of the emitted zinc stays in the technosphere, the total amount entering this target zone along highways is limited. From the 140 tons of zinc per year that is released from tyre wear in The Netherlands, 64 tons is emitted in the urban area, 6.5 tons reaches to the target zones of all roads and only 1.1 tons of zinc will enter the target zone along highways. This amount will be further decreased by the application of porous asphalt in the near future. The emission from safety fence corrosion does not enter

Roads Belong in the Urban Landscape

DEFF Research Database (Denmark)

Clemmensen, Thomas Juel

2013-01-01

Roads are often associated with a fragmentation or splintering of landscapes and their natural connectivity; particularly in relation to ‘green infrastructure’ they are often considered problematic elements that rupture and barricade. Conversely, as part of larger networks, roads can be considered...... important elements in the creation of new, ‘green infrastructures’ that can qualify urban landscapes in terms of improving their overall porosity and connectivity. This argument will be unfolded and substantiated in this article through theoretical reflections which conceptually re-locate road networks...... in the urban landscape, supported by relevant reference projects that illustrate the potential of road networks as a platform for ‘green infrastructure’....

2010/11 McMurdo Station Snow Road Strength and Maintenance

Science.gov (United States)

2017-02-01

McMurdo Station. Part of this study in- cluded tracking the road maintenance and temperature and testing the road strength at predetermined mile...data provides insight as to the direct effects of various maintenance and environmental factors on the strength of the roads . Un- derstanding the...13 4.2 Maintenance vs. road strength

Australian road rules

Science.gov (United States)

2009-02-01

*These are national-level rules. Australian Road Rules - 2009 Version, Part 18, Division 1, Rule 300 "Use of Mobile Phones" describes restrictions of mobile phone use while driving. The rule basically states that drivers cannot make or receive calls ...

Natural frequencies of a flat viaduct road part simply supported on ...

Indian Academy of Sciences (India)

Viaduct roads have wide application in big cities with high traffic ... the solutions of plates that have various boundary conditions, numerical methods must be .... algorithm, in the most general condition, we get output and hidden layer equations ...

Development and enhancement of road lighting principles

Energy Technology Data Exchange (ETDEWEB)

Ekrias, A.

2010-07-01

The work starts with a short introduction concerning the history of road lighting, outlining the trends and changes that have taken place in road lighting research during the past century. The introduction is followed by a review of trends, directions, and problems in current road lighting research and practice. The following part of the work introduces an advanced approach to road lighting measurements and calculations, based on the use of an imaging luminance photometer and the Road LumiMeter v2.0 computer program. The work sets out to investigate the variations in the characteristics of the quality of the road lighting at the same pilot locations in relation to the calculation methods used. In the work mesopic visual performance and the effects of the spectral transmittance of the vehicle windshield on the visibility conditions of the driver are also analysed. The work continues with road lighting measurements in various weather conditions in order to study the effects of snowy and wet road surface conditions on road lighting luminances. The results show that in Finland, snowy conditions offer very good opportunities to save electricity without adversely affecting either the safety of driving or the quality of road lighting. The following measurements set out to investigate the contribution of halogen and high-intensity discharge headlights to road lighting and whether this has a conflicting effect on the luminance contrasts of various targets located on the road or at the side of the road. The results indicate that, in general, the use of vehicle headlights in the presence of road lighting reduces the luminance contrasts of targets. The work continues with road lighting visibility experiments which study the visibility of achromatic and coloured targets in MH lamp and HPS lamp installations. The results show that colours have a major effect on target visibility if the road is illuminated with a light source with adequate colour rendering properties. Finally

Roads Belong In the Urban Landscape

DEFF Research Database (Denmark)

Clemmensen, Thomas Juel

2012-01-01

In spite of being an essential part of the system of automobility and as such playing an important role in the development of urban landscapes, road networks seldom attracts much attention among architects involved in the planning and design of urban landscapes. One reason is probably found...... in the dominance of the zoning approach to planning, where road planning easily becomes isolated and reduced to a matter of traffic regulation and transport economy. Another possible reason could be, as suggested by the Australian landscape architect Christopher Sawyer, that road networks like other...... as landscape architects engage with road networks in profound ways, which moves beyond the purely visual and pictorial? Is it possible to conceptually (re)locate road networks in the landscape? The paper will address these questions by discussing different understandings of landscape and its relation...

The Road to a Court of Appeal—Part II: Distinguishing Features and Establishment

DEFF Research Database (Denmark)

Butler, Graham

2015-01-01

of the road taken. By mapping the sequence of events that lead to the creation of the new court, the complexity that goes into large-scale judicial restructuring can begin to be fully appreciated. This is the second and concluding part of the article, covering the distinguishing features and establishment......-lasting effects on the judicial system of the state. The creation of a new court takes a considerable effort from a number of branches of the State, in formulating the correct path for its establishment to proceed. In this article, the history of a Court of Appeal is set out, before discussing the referendum...... to amend the Constitution to allow for it. This is followed by looking at some of the provisions of the Amendment Bill that was put before both the Oireachtas and the people, before looking at three distinguishing features of the Bill, and finally discussing its establishment in 2014, along with analysis...

Verification of road databases using multiple road models

Science.gov (United States)

Ziems, Marcel; Rottensteiner, Franz; Heipke, Christian

2017-08-01

In this paper a new approach for automatic road database verification based on remote sensing images is presented. In contrast to existing methods, the applicability of the new approach is not restricted to specific road types, context areas or geographic regions. This is achieved by combining several state-of-the-art road detection and road verification approaches that work well under different circumstances. Each one serves as an independent module representing a unique road model and a specific processing strategy. All modules provide independent solutions for the verification problem of each road object stored in the database in form of two probability distributions, the first one for the state of a database object (correct or incorrect), and a second one for the state of the underlying road model (applicable or not applicable). In accordance with the Dempster-Shafer Theory, both distributions are mapped to a new state space comprising the classes correct, incorrect and unknown. Statistical reasoning is applied to obtain the optimal state of a road object. A comparison with state-of-the-art road detection approaches using benchmark datasets shows that in general the proposed approach provides results with larger completeness. Additional experiments reveal that based on the proposed method a highly reliable semi-automatic approach for road data base verification can be designed.

Environmental exposure of road borders to zinc

Energy Technology Data Exchange (ETDEWEB)

Blok, J. [Royal Haskoning, P.O. Box 151, 6500 Ad Nijmegen (Netherlands)]. E-mail: Han.Blok@royalhaskoning.com

2005-09-15

The emissions of zinc along roads originating from tyre wear, corrosion of safety fence and other traffic-related sources have been quantified and validated by measured long-term loads in road run-off and airborne solids (drift) for 29 published case studies. The distribution pattern over the road border at various distances from the edge of the paved surface is assessed on the basis of 38 published case studies with measured concentrations in soil. For the impact assessment, the road border is differentiated into a zone that is part of the 'technosphere' and the 'target zone' beyond that technosphere that can be considered as part of the receiving environment. The 'technosphere' of the road includes the central reservation, the hard and the soft shoulder or, if one or both shoulders are not present, the so-called obstacle 'free zone' that is defined by road engineers. Pollution within the technosphere may require appropriate management of solid disposal and isolation from groundwater to prevent further distribution of pollutants to the environment. In the target zone along regional roads, the zinc load is about 4 mg/m{sup 2} year and this is of the same order of magnitude as that of atmospheric deposition in areas beyond the influence of roads (background). In the target zone along highways, the zinc load is increased in comparison to the background deposition. The average load of about 38 mg/m{sup 2} year is similar to that in fertilised agricultural land. Because most of the emitted zinc stays in the technosphere, the total amount entering this target zone along highways is limited. From the 140 tons of zinc per year that is released from tyre wear in The Netherlands, 64 tons is emitted in the urban area, 6.5 tons reaches to the target zones of all roads and only 1.1 tons of zinc will enter the target zone along highways. This amount will be further decreased by the application of porous asphalt in the near future. The

Road profile estimation of city roads using DTPS

Science.gov (United States)

Wang, Qi; McDaniel, J. Gregory; Sun, Nian X.; Wang, Ming L.

2013-04-01

This work presents a non-destructive and non-contact acoustic sensing approach for measuring road profile of road and bridge deck with vehicles running at normal speed without stopping traffic. This approach uses an instantaneous and real-time dynamic tire pressure sensor (DTPS) that can measure dynamic response of the tire-road interaction and increases the efficiency of currently used road profile measuring systems with vehicle body-mounted profilers and axle-mounted accelerometers. In this work, a prototype of real-time DTPS system has been developed and demonstrated on a testing van at speeds from 5 to 80 miles per hour (mph). A data analysis algorithm has been developed to remove axle dynamic motions from the measured DTPS data and to find the transfer function between dynamic tire pressure change and the road profile. Field test has been performed to estimate road profiles. The road profile resolution is approximately 5 to 10 cm in width and sensitivity is 0. 3 cm for the height road surface features at driving speeds of 5 to 80 mph.

FORMATION PROCESS AND HISTORICAL FUNCTIONS OF OLD AKIHA ROAD

Science.gov (United States)

Nakane, Yoji; Okuda, Masao; Kani, Yukihiko; Hayakawa, Kiyoshi; Matsui, Tamotsu

An object of this study is the old Akiha road located along the southern parts of the Akaishi Mountains in Sizuoka Prefecture. The old Akiha road between Hamamatsu city in Enshu and Iida city in Shinshu had been utilized by people for the purposes of making a pilgrimage, megalithic faith, transporting obsidian since the primitive age, practicing the mountaineering asceticism, operating the military activities in the warlike age, transporting salt from coastal area to mountainous area and so on. Through the investigation of literature, site reconnaissance and hearing, the formation process and the historical functions of the old Akiha road were studied, including the situation in medieval times or before. As the results, it was elucidated that the oldest road between two cities had located over the Hyoukoshi Pass, the road routes had the lowering trend from mountainside to riverside, and the historical functions of old Akiha road were the passage for transportation of various kinds of goods and human being, faith and culture.

Politics of contemporary "Silk Roads"

Directory of Open Access Journals (Sweden)

Andrey I. Litvinov

2016-01-01

Full Text Available Recently in mass media we can find the idea about a new Silk Road or the concept of "Silk Road Economic Belt" which has been formulated by the Chinese PresidentXi Jinping on September 7,2013, during his official visit to Kazakhstan. This project is not only the creation of a transport, power and trade corridor, and also the project which will promote development of tourism in the region and to strengthening of cultural exchanges of China with the countries of Central Asia, it also includes construction of a network of high-speed fiber-optical networks. The economic strip of the Silk Road will begin in China and pass across the Central and the Southern Asia, part of branches across the territory of the Russian Federation and to leave to Europe. This international investment project assumes creation of a continental transport way. For implementation of overland part of "A great Silk Road is a three railway corridors (northern, central have to be constructed and southern They have form a basis for development of other means of transport, including automobile subsequently. Construction of these three railway corridors acts as the most important and necessary stage of implementation of the project. The government of China declares that creation of an economic belt of the Silk way is a revival of once prospering trade-transport and cultural corridor from Asia to Europe which will promote activization of a friendly exchange between the people of the different countries. Further all this has to connect trade and economic space of Europe and Asia in a whole that has to serve implementation of deeper economic cooperation, between the countries participating in him, to increase in a trade turnover and expansion of scientific and technical exchanges between them.

Seerley Road Fire Site

Science.gov (United States)

A barn caught fire at on Seerley Road, Indianapolis. Five storage drums believed to contain metallic potassium were involved in the fire. EPA will perform additional sampling as part of removal operations and safe offsite transportation.

Tapping the potential for reducing work-related road deaths and injuries.

NARCIS (Netherlands)

Adminaite, D. Jost, G. Stipdonk, H. & Ward, H.

2017-01-01

Over 25,600 lives were lost on the road in the European Union in 2016, of those a large proportion were victims of work-related road (WRR) collisions. Even though the exact number is unknown, it is likely that up to 40% of all road deaths are work-related. Part I: Work-related road safety (WRRS)

The road safety audit and road safety inspection.

NARCIS (Netherlands)

2007-01-01

A road safety audit (RSA) and a road safety inspection (RSI) are used to test the safety level of the road infrastructure. The RSA tests the design of new roads or the reconstruction of existing roads, whereas the RSI is used for testing existing roads. An RSA, therefore, aims to 'improve' the road

Introduction to special issue on hydrologic and geomorphic effects of forest roads

Science.gov (United States)

Charles H. Luce; Beverley C. Wemple

2001-01-01

Roads have been a part of human landscapes for more than 40 centuries. During the 20th century, technological advances have increased our ability to construct new roads at unprecedented rates and into steeper terrain. In the last half of that century, an extensive network of roads has been constructed in forests and other wildlands to facilitate use and management of...

25 CFR 170.138 - Can roads be built in roadless and wild areas?

Science.gov (United States)

2010-04-01

... RESERVATION ROADS PROGRAM Indian Reservation Roads Program Policy and Eligibility Recreation, Tourism and Trails § 170.138 Can roads be built in roadless and wild areas? Under 25 CFR part 265 no roads can be...

Climate Projection Data base for Roads - CliPDaR: Design a guideline for a transnational database of downscaled climate projection data for road impact models - within the Conference's of European Directors of Roads (CEDR) TRANSNATIONAL ROAD RESEARCH PROG

Science.gov (United States)

Matulla, Christoph; Namyslo, Joachim; Fuchs, Tobias; Türk, Konrad

2013-04-01

The European road sector is vulnerable to extreme weather phenomena, which can cause large socio-economic losses. Almost every year there occur several weather triggered events (like heavy precipitation, floods, landslides, high winds, snow and ice, heat or cold waves, etc.), that disrupt transportation, knock out power lines, cut off populated regions from the outside and so on. So, in order to avoid imbalances in the supply of vital goods to people as well as to prevent negative impacts on health and life of people travelling by car it is essential to know present and future threats to roads. Climate change might increase future threats to roads. CliPDaR focuses on parts of the European road network and contributes, based on the current body of knowledge, to the establishment of guidelines helping to decide which methods and scenarios to apply for the estimation of future climate change based challenges in the field of road maintenance. Based on regional scale climate change projections specific road-impact models are applied in order to support protection measures. In recent years, it has been recognised that it is essential to assess the uncertainty and reliability of given climate projections by using ensemble approaches and downscaling methods. A huge amount of scientific work has been done to evaluate these approaches with regard to reliability and usefulness for investigations on possible impacts of climate changes. CliPDaR is going to collect the existing approaches and methodologies in European countries, discuss their differences and - in close cooperation with the road owners - develops a common line on future applications of climate projection data to road impact models. As such, the project will focus on reviewing and assessing existing regional climate change projections regarding transnational highway transport needs. The final project report will include recommendations how the findings of CliPDaR may support the decision processes of European

ROAD REPAIR WORKS ON THE MEYRIN SITE

CERN Multimedia

ST-TFM Group

2001-01-01

ST Division will proceed, as from Monday 23 July, in repairing some parts of roads on the Meyrin site (see drawing). This work will last for one week depending on the weather conditions and will cause some traffic hold ups during this period. Please follow the indications on the temporary road signs. Thanking you in advance for your comprehension.

Material and component road map

International Nuclear Information System (INIS)

Korea Industrial Technology Foundation Editorial Department

2007-09-01

This book is comprised of two parts. One is divided into five chapters, which deals with summary of environment-friendly coloring technology, industry tendency of environment-friendly coloring technology, industry analysis and vision of environment-friendly coloring technology, analysis on core technology for environment-friendly coloring technology, with eco-friendly water paint and painting skill and eco-friendly surface treatment skill using electrochemical process. The other is divided into five chapters, which handles outline of display printing technology road map market trends of display painting, analysis and vision of display painting deduction of core-technology for display painting and analysis of core-technology for display painting. It has Diagrams for eco-friendly coloring technology road map and core-technology display painting road map.

Road binders and energy savings. Strassenbau und Energie, Verwendung energiesparender Bindemittel

Energy Technology Data Exchange (ETDEWEB)

1987-01-01

This report is the outcome of a joint research project carried through by an international group of experts. The object was to establish whether current advances in research and practice permit to reduce energy consumption, especially the consumption of petroleum products, by making substitution, either in part or in full, for traditional binders in the construction, maintenance and strengthening of road pavements. The first part deals with bituminous binders, the second part is dedicated to hydraulic binders. As regards the possibility to make substitution for bitumen, the following materials are investigated: coal tar, sulfur, plastics, lignin, and natural rock impregnated with carbohydrates. The modification of the properties of bitumens (through polymers or rubber wastes), the use of emulsions, and the recovery of old road construction materials are dealt with in separate chapters. As regards hydraulic binders, the report investigates cements of low energy content, industrial by-products, and natural materials with hydraulic or pozzolanic properties as well as substandard materials. A separate chapter is dedicated to the possibility of reducing the thickness of the bituminous road cover over road bases with hydraulic binders. The appendix contains detailed energy balances for current road construction materials and pavement constructions. The report is meant to constitute a decision-aid for road authorities and contractors working in the public sector in choosing appropriate road construction materials and techniques on the basis of rational criteria. (orig.)

The ecological impact assessment of a proposed road development (the Slovak approach)

International Nuclear Information System (INIS)

Igondova, Erika; Pavlickova, Katarina; Majzlan, Oto

2016-01-01

The construction of roads is one of the most widespread forms of natural landscape modification. Over the last 20 years, dozens of road constructions have been assessed in Slovakia, which makes it possible to talk about methodological positives and negatives. A special feature of Slovakia is that many planned or renovated roads are located in protected areas or are in contact with them (including Natura 2000 sites). Therefore, it is important to understand the scope of the roads' ecological impacts and find ways for their appropriate evaluation and incorporation into the Environmental Impact Assessment process. For this reason, the Ecological Impact Assessment methodology can be used as a basis for our research, which consists of three stages. In the first stage (scoping), a buffer circumventing the proposed road is created to determine the area for impact prediction and evaluation. Subsequently, the landscape structure and baseline landscape conditions are discussed, a map of current landscape structure is created and the current ecological status of the affected area is calculated. In the second stage (the evaluation of ecological resources), important ecological parts of the landscape are delineated. This step is based on the importance of previous information and its vulnerability, and leads to the mapping of the road ecological impact zone. In the third stage (impact assessment), important ecological parts are spatially correlated with the proposed road construction. Finally, the significance of ecological impacts of the activity is evaluated by applying specific criteria (duration, reversibility, magnitude, size and road ecological impact zone significance). A scale is proposed for each criterion to evaluate the total significance of impacts. In this way, detailed significant ecological impacts can be found which will help lead to proposed correct mitigation measures and a post-project analysis. - Highlights: • This paper proposes a methodology for the Ec

The ecological impact assessment of a proposed road development (the Slovak approach)

Energy Technology Data Exchange (ETDEWEB)

Igondova, Erika, E-mail: erika.igondova@gmail.com; Pavlickova, Katarina, E-mail: pavlickova60@gmail.com; Majzlan, Oto, E-mail: majzlan@fns.uniba.sk

2016-07-15

The construction of roads is one of the most widespread forms of natural landscape modification. Over the last 20 years, dozens of road constructions have been assessed in Slovakia, which makes it possible to talk about methodological positives and negatives. A special feature of Slovakia is that many planned or renovated roads are located in protected areas or are in contact with them (including Natura 2000 sites). Therefore, it is important to understand the scope of the roads' ecological impacts and find ways for their appropriate evaluation and incorporation into the Environmental Impact Assessment process. For this reason, the Ecological Impact Assessment methodology can be used as a basis for our research, which consists of three stages. In the first stage (scoping), a buffer circumventing the proposed road is created to determine the area for impact prediction and evaluation. Subsequently, the landscape structure and baseline landscape conditions are discussed, a map of current landscape structure is created and the current ecological status of the affected area is calculated. In the second stage (the evaluation of ecological resources), important ecological parts of the landscape are delineated. This step is based on the importance of previous information and its vulnerability, and leads to the mapping of the road ecological impact zone. In the third stage (impact assessment), important ecological parts are spatially correlated with the proposed road construction. Finally, the significance of ecological impacts of the activity is evaluated by applying specific criteria (duration, reversibility, magnitude, size and road ecological impact zone significance). A scale is proposed for each criterion to evaluate the total significance of impacts. In this way, detailed significant ecological impacts can be found which will help lead to proposed correct mitigation measures and a post-project analysis. - Highlights: • This paper proposes a methodology for the

Road Assessment Model and Pilot Application in China

Directory of Open Access Journals (Sweden)

Tiejun Zhang

2014-01-01

Full Text Available Risk assessment of roads is an effective approach for road agencies to determine safety improvement investments. It can increases the cost-effective returns in crash and injury reductions. To get a powerful Chinese risk assessment model, Research Institute of Highway (RIOH is developing China Road Assessment Programme (ChinaRAP model to show the traffic crashes in China in partnership with International Road Assessment Programme (iRAP. The ChinaRAP model is based upon RIOH’s achievements and iRAP models. This paper documents part of ChinaRAP’s research work, mainly including the RIOH model and its pilot application in a province in China.

Roads Investments, Spatial Intensification and Deforestation in the Brazilian Amazon

Science.gov (United States)

Pfaff, Alexander; Robalino, Juan; Walker, Robert; Aldrich, Steven; Caldas, Marcellus; Reis, Eustaquio; Perz, Stephen; Bohrer, Claudio; Arima, Eugenio; Laurance, William;

Residential proximity to major roads and term low birth weight: the roles of air pollution, heat, noise, and road-adjacent trees.

Science.gov (United States)

Dadvand, Payam; Ostro, Bart; Figueras, Francesc; Foraster, Maria; Basagaña, Xavier; Valentín, Antònia; Martinez, David; Beelen, Rob; Cirach, Marta; Hoek, Gerard; Jerrett, Michael; Brunekreef, Bert; Nieuwenhuijsen, Mark J

2014-07-01

Maternal residential proximity to roads has been associated with adverse pregnancy outcomes. However, there is no study investigating mediators or buffering effects of road-adjacent trees on this association. We investigated the association between mothers' residential proximity to major roads and term low birth weight (LBW), while exploring possible mediating roles of air pollution (PM(2.5), PM(2.5-10), PM(10), PM(2.5) absorbance, nitrogen dioxide, and nitrogen oxides), heat, and noise and buffering effect of road-adjacent trees on this association. This cohort study was based on 6438 singleton term births in Barcelona, Spain (2001-2005). Road proximity was measured as both continuous distance to and living within 200 m from a major road. We assessed individual exposures to air pollution, noise, and heat using, respectively, temporally adjusted land-use regression models, annual averages of 24-hour noise levels across 50 m and 250 m, and average of satellite-derived land-surface temperature in a 50-m buffer around each residential address. We used vegetation continuous fields to abstract tree coverage in a 200-m buffer around major roads. Living within 200 m of major roads was associated with a 46% increase in term LBW risk; an interquartile range increase in heat exposure with an 18% increase; and third-trimester exposure to PM(2.5), PM(2.5-10), and PM10 with 24%, 25%, and 26% increases, respectively. Air pollution and heat exposures together explained about one-third of the association between residential proximity to major roads and term LBW. Our observations on the buffering of this association by road-adjacent trees were not consistent between our 2 measures of proximity to major roads. An increased risk of term LBW associated with proximity to major roads was partly mediated by air pollution and heat exposures.

Causes of road traffic accidents in Juba

African Journals Online (AJOL)

2017-05-02

May 2, 2017 ... Introduction: Road traffic accidents (RTAs) are a major cause of death and disability in ... death in many parts of the world resulting in economic ... The long civil war ... the second highest number compared to private cars. In.

Safer Roads: Comparisons Between Road Assessment Program and Composite Road Safety Index Method

Directory of Open Access Journals (Sweden)

Mohd Razelan Intan Suhana

2017-01-01

Full Text Available In most countries, crash statistics have becoming very crucial in evaluating road’s safety level. In Malaysia, these data are very important in deciding crash-prone areas known as black spot where specific road improvements plan will be proposed. However due to the unavailability of reliable crash data in many developing countries, appropriate road maintenance measures are facing great troubles. In light of that, several proactive methods in defining road’s safety level such as Road Assessment Program (RAP have emerged. This research aim to compare two proactive methods that have been tested in Malaysian roads ; road assessment program and road environment risk index which was developed based on composite index theory in defining road’s safety level. Composite road environment risk index was combining several crucial environment indicators, assigning weight and aggregating the individual index together to form a single value representing the road’s safety level. Based on the results, it can be concluded that both road assessment program and composite road environment risk index are contradicted in six different ways such as type of speed used, type of analysis used and their final outcomes. However, with an aim to promote safer roads, these two methods can be used concurrently as the outcomes in both methods seems to fulfil each other’s gap very well.

Traffic noise in Hyderabad city, part-II. vehicular contribution to road traffic noise

International Nuclear Information System (INIS)

Sheikh, G.H.

2001-01-01

The results of a road traffic noise survey carried out in Hyderabad city showed that the levels of traffic noise in the City are alarmingly high and much beyond the comfortable limits. There, in order to investigate the level of the noise emitted by different types of vehicles plying on the city roads and to assess their individual contribution to high level traffic noise, studies have been carried out on the measurement of noise emitted by motorcycles, buses, auto-rickshaws, and motor vehicle horns as they normally move on the city roads. The data collected has been analyzed for L/sub v99/, L/sub v90/, L/sub v50/, L/sub v10/ and L/sub v1/ and results are discussed with reference to the existing motor vehicle rules in Pakistan and motor vehicle noise emission limits set by the EEC and other developed countries. Some suggestion have also been made to limit high level traffic noise. (author)

Road repair works on the Meyrin site

CERN Multimedia

2003-01-01

ST Division will proceed, as from Monday 15th of September, in repairing some parts of roads on the Meyrin site (see drawing). This work will last for three weeks depending on the weather conditions and will cause some traffic hold ups during this period. Please follow the indications on the temporary road signs. Thanking you in advance for your comprehension. ST-CE and ST-FM Groups GSM 160224 - 163976

Automatic Road Centerline Extraction from Imagery Using Road GPS Data

Directory of Open Access Journals (Sweden)

Chuqing Cao

2014-09-01

Full Text Available Road centerline extraction from imagery constitutes a key element in numerous geospatial applications, which has been addressed through a variety of approaches. However, most of the existing methods are not capable of dealing with challenges such as different road shapes, complex scenes, and variable resolutions. This paper presents a novel method for road centerline extraction from imagery in a fully automatic approach that addresses the aforementioned challenges by exploiting road GPS data. The proposed method combines road color feature with road GPS data to detect road centerline seed points. After global alignment of road GPS data, a novel road centerline extraction algorithm is developed to extract each individual road centerline in local regions. Through road connection, road centerline network is generated as the final output. Extensive experiments demonstrate that our proposed method can rapidly and accurately extract road centerline from remotely sensed imagery.

Effect of the Road Environment on Road Safety in Poland

Science.gov (United States)

Budzynski, Marcin; Jamroz, Kazimierz; Antoniuk, Marcin

2017-10-01

Run-off-road accidents tend to be very severe because when a vehicle leaves the road, it will often crash into a solid obstacle (tree, pole, supports, front wall of a culvert, barrier). A statistical analysis of the data shows that Poland’s main roadside hazard is trees and the severity of vehicles striking a tree in a run-off-road crash. The risks are particularly high in north-west Poland with many of the roads lined up with trees. Because of the existing rural road cross-sections, i.e. having trees directly on road edge followed immediately by drainage ditches, vulnerable road users are prevented from using shoulders and made to use the roadway. With no legal definition of the road safety zone in Polish regulations, attempts to remove roadside trees lead to major conflicts with environmental stakeholders. This is why a compromise should be sought between the safety of road users and protection of the natural environment and the aesthetics of the road experience. Rather than just cut the trees, other road safety measures should be used where possible to treat the hazardous spots by securing trees and obstacles and through speed management. Accidents that are directly related to the road environment fall into the following categories: hitting a tree, hitting a barrier, hitting a utility pole or sign, vehicle rollover on the shoulder, vehicle rollover on slopes or in ditch. The main consequence of a roadside hazard is not the likelihood of an accident itself but of its severity. Poland’s roadside accident severity is primarily the result of poor design or operation of road infrastructure. This comes as a consequence of a lack of regulations or poorly defined regulations and failure to comply with road safety standards. The new analytical model was designed as a combination of the different factors and one that will serve as a comprehensive model. It was assumed that it will describe the effect of the roadside on the number of accidents and their consequences

Road user behaviour changes following a self-explaining roads intervention.

Science.gov (United States)

Mackie, Hamish W; Charlton, Samuel G; Baas, Peter H; Villasenor, Pablo C

2013-01-01

The self-explaining roads (SER) approach uses road designs that evoke correct expectations and driving behaviours from road users to create a safe and user-friendly road network. Following the implementation of an SER process and retrofitting of local and collector roads in a suburb within Auckland City, lower speeds on local roads and less variation in speed on both local and collector roads were achieved, along with a closer match between actual and perceived safe speeds. Preliminary analyses of crash data shows that the project has resulted in a 30% reduction crash numbers and an 86% reduction in crash costs per annum, since the road changes were completed. In order to further understand the outcomes from this project, a study was carried out to measure the effects of the SER intervention on the activity and behaviour of all road users. Video was collected over nine separate days, at nine different locations, both before and after SER construction. Road user behaviour categories were developed for all potential road users at different location types and then used to code the video data. Following SER construction, on local roads there was a relatively higher proportion of pedestrians, less uniformity in vehicle lane keeping and less indicating by motorists along with less through traffic, reflecting a more informal/low speed local road environment. Pedestrians were less constrained on local roads following SER construction, possibly reflecting a perceptually safer and more user-friendly environment. These behaviours were not generally evident on collector roads, a trend also shown by the previous study of speed changes. Given that one of the objectives of SER is to match road user behaviour with functionally different road categories, the road user behaviour differences demonstrated on different road types within the SER trial area provides further reinforcement of a successful SER trial. Copyright © 2012 Elsevier Ltd. All rights reserved.

Performance of Roads In Seismic Conditions: A Theoretical And Experimental Study

International Nuclear Information System (INIS)

Pratico, Filippo Giammaria

2008-01-01

As is well known, the role of the road network during and after an earthquake is of paramount relevance. In the light of the above, the main goal of the paper has been confined to the analyses of road performance in seismic conditions, as a result of intrinsic (structural and functional conditions, redundancy, etc.) and extrinsic (loads, flows, etc.) characteristics. Such interaction has been analysed for the area of Reggio Calabria and Messina Strait, through 28 equations and a number of models and simulations. Analyses proved that redundancy is a key-factor, able to affect the overall performance of the road network. Simulations demonstrated that in the long term road serviceability could be partly compromised, but accident risk, due to speed limitations, could result decreased

Drawing road networks with focus regions.

Science.gov (United States)

Haunert, Jan-Henrik; Sering, Leon

2011-12-01

Mobile users of maps typically need detailed information about their surroundings plus some context information about remote places. In order to avoid that the map partly gets too dense, cartographers have designed mapping functions that enlarge a user-defined focus region--such functions are sometimes called fish-eye projections. The extra map space occupied by the enlarged focus region is compensated by distorting other parts of the map. We argue that, in a map showing a network of roads relevant to the user, distortion should preferably take place in those areas where the network is sparse. Therefore, we do not apply a predefined mapping function. Instead, we consider the road network as a graph whose edges are the road segments. We compute a new spatial mapping with a graph-based optimization approach, minimizing the square sum of distortions at edges. Our optimization method is based on a convex quadratic program (CQP); CQPs can be solved in polynomial time. Important requirements on the output map are expressed as linear inequalities. In particular, we show how to forbid edge crossings. We have implemented our method in a prototype tool. For instances of different sizes, our method generated output maps that were far less distorted than those generated with a predefined fish-eye projection. Future work is needed to automate the selection of roads relevant to the user. Furthermore, we aim at fast heuristics for application in real-time systems. © 2011 IEEE

Tire-road noise: an experimental study of tire and road design parameters

OpenAIRE

Bekke, Dirk; Wijnant, Ysbrand H.; Weegerink, Thijs; de Boer, Andries

2013-01-01

It is widely known that road traffic noise has negative influences on human health. Hence, as tire-road noise is considered to be the most dominant cause of road traffic noise above 30-50 km/h, a lot of research is performed by the two involving industries: road authorities/manufacturers and tire manufacturers. Usually, the parameters influencing exterior tire-road noise are often examined separately, whereas it is the tire-road interaction which obviously causes the actual noise. An integral...

Strabo's roads

DEFF Research Database (Denmark)

Bekker-Nielsen, Tønnes

2017-01-01

in the Geography, and the world-view, of Strabo. Strabo did not take much interest in roads as artefacts or monuments, in the technology of road construction, or in the mythological and historical background of individual roads. He is primarily interested in roads from a functional point of view. For the general......To ancient geographers, roads were important not only as arteries of communication, but also as sources of information, since mileages measured along the Roman highways were among the very few precise distances available to the ancient geographer. This chapter explores the place of roads...... or the statesman, roads provide routes of communication; for the systematic geographer, they provide measured distances and directions. Through case studies of Spain, Gaul, Italy, Greece and Anatolia, this chapter attempts to reach a better understanding of the place of roads in Strabo’s universe, especially two...

[Accidents on Iceland's most dangerous roads].

Science.gov (United States)

Bjarnason, Thóroddur; Arnarsson, Sveinn

2012-02-01

The objective of this paper was to identify the most dangerous segments of the Icelandic road system in terms of the number of accidents pr km and the rate of accidents pr million km travelled. First to identify the segments where the number of accidents is highest and where the risk of the individual traveller is the greatest. Second to evaluate if the association between the number and the rate of accidents is positive or negative. Third to identify the road segments that are the most dangerous in the sense of many accidents and great risk to individual travellers. Main roads outside urban centers were divided into 45 segments that were on average 78 km in length. Infrequently travelled roads and roads within urban centers were omitted. Information on the length of roads, traffic density and number of accidents was used to calculate the number of accidents per km and the rate of accidents per million km travelled. The correlation between the number and rate of accidents was calculated and the most dangerous road segments were identified by the average rank order on both dimensions. Most accidents pr km occurred on the main roads to and from the capital region, but also east towards Hvolsvöllur, north towards Akureyri and in the Mideast region of the country. The rate of accidents pr million km travelled was highest in the northeast region, in northern Snæfellsnes and in the Westfjords. The most dangerous roads on both dimensions were in Mideast, northern Westfjords, in the north between Blönduós and Akureyri and in northern Snæfellsnes. Most accidents pr km occurred on roads with a low accident rate pr million km travelled. It is therefore possible to reduce accidents the most by increasing road safety where it is already the greatest but that would however increase inequalities in road safety. Policy development in transportation is therefore in part a question of priorities in healthcare. Individual equality in safety and health are not always fully

[Prevention of road accidents in the road haulage field].

Science.gov (United States)

Rosso, G L; Zanelli, R; Corino, P; Bruno, S

2007-01-01

Every year many traffic accidents with fatal outcomes occur in our Country. According to the recent indications of the European Agency for Safety and Health at Work, the Piedmont region has financed the plan: Prevention of road accidents in the road haulage field. The aims of the plan are to stimulate transport companies to the target of road safety and to improve and enforce sanitary surveillance, in order to improve the safety on road haulage and to prevent traffic injuries. the plan foresees, over a period of two years, a few encounters with all the interested parties (companies, police forces, labour unions etc). During those encounters we have to give a questionnaire for evaluating the companies' knowledge about the problem and we have to choose a common plan with the aim of improving road safety. The Piedmont regional plan recalls the need to increase the attention to numerous and diversified hazards for safety on road haulage. It also imposes the choice of measures that include: risk assessment, health education, technical and environmental prevention, sanitary surveillance and clinical interventions (diagnosis and rehabilitation of occupational accidents).

Radiation load of the electro-thermal production of phosphorus. Part 2. The inhalation dose in road construction

International Nuclear Information System (INIS)

Erkens, W.H.H.; Hermans, P.M.J.A.; Timmermans, C.W.M.

2003-01-01

The phosphate ore which is processed by Thermphos International in Vlissingen, Netherlands, to produce element phosphorus contains circa 1 Bq per gram uranium 238. As a result of this production process radionuclides are emitted and slags that contain natural radioisotopes are formed. The slags can be used as a building material for roads and water works. During the production of phosphorus the waste material calcinate is formed as well. Operators, working in the production process of phosphorus and laborers, working in road construction and hydraulic engineering inhale radioisotopes. In two articles attention will be paid to the inhalation doses, how the doses are measured, measures that were taken to reduce and control the doses, and the ALARA-principles. This article is focused on the inhalation doses for road construction workers [nl

Social costs of road crashes: An international analysis.

Science.gov (United States)

Wijnen, Wim; Stipdonk, Henk

2016-09-01

This paper provides an international overview of the most recent estimates of the social costs of road crashes: total costs, value per casualty and breakdown in cost components. The analysis is based on publications about the national costs of road crashes of 17 countries, of which ten high income countries (HICs) and seven low and middle income countries (LMICs). Costs are expressed as a proportion of the gross domestic product (GDP). Differences between countries are described and explained. These are partly a consequence of differences in the road safety level, but there are also methodological explanations. Countries may or may not correct for underreporting of road crashes, they may or may not use the internationally recommended willingness to pay (WTP)-method for estimating human costs, and there are methodological differences regarding the calculation of some other cost components. The analysis shows that the social costs of road crashes in HICs range from 0.5% to 6.0% of the GDP with an average of 2.7%. Excluding countries that do not use a WTP- method for estimating human costs and countries that do not correct for underreporting, results in average costs of 3.3% of GDP. For LMICs that do correct for underreporting the share in GDP ranges from 1.1% to 2.9%. However, none of the LMICs included has performed a WTP study of the human costs. A major part of the costs is related to injuries: an average share of 50% for both HICs and LMICs. The average share of fatalities in the costs is 23% and 30% respectively. Prevention of injuries is thus important to bring down the socio-economic burden of road crashes. The paper shows that there are methodological differences between countries regarding cost components that are taken into account and regarding the methods used to estimate specific cost components. In order to be able to make sound comparisons of the costs of road crashes across countries, (further) harmonization of cost studies is recommended. This can be

Understanding road safety in Kenya: views of matatu drivers.

Science.gov (United States)

Raynor, Nicolas J; Mirzoev, Tolib

2014-09-01

Road traffic accidents (RTAs) are estimated to cause 1.3 million deaths and 20-50 million injuries worldwide. Road safety is a challenge in Kenya with causes being multi-factorial. Matatus (minibuses) are involved in a large proportion of accidents. A literature review was completed to identify key issues and refine the scope of the study. The fieldwork included 20 semi-structured interviews with matatu drivers. All participants were male, with driving experience of 1-20 years. Thematic framework was used for analysis. Some unstructured observations on different road users and their behaviours were also recorded. Literature showed that the causes of RTAs in Kenya are multi-factorial, but that human factors play a large part. There is also an evidence gap concerning matatu drivers, who are key stakeholders in road safety. Fieldwork showed that the matatu industry creates financial pressures on drivers and an excessive level of competition, leading to dangerous driving. Corruption of traffic police appears to be a major barrier to improving road safety, as road safety legislation is not enforced, and bribery has become the cultural norm. The general public, including passengers and private vehicles owners, also cause problems by failing to understand their role in road safety and placing the blame on others. The key policy implication for improving road safety in Kenya is seeking measures to ensure responsibility by all road users through awareness raising in the short-term and reforming the matatu industry and addressing the root causes of corruption in the longer term. © The Author 2014. Published by Oxford University Press on behalf of Royal Society of Tropical Medicine and Hygiene. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Econometric models of road use, accidents, and road investment decisions. Volume 1 : introductory overview, the barely revealed preference behind road investment priorities (essay 1), measuring the contribution of randomness, exposure, weather, and daylig

Science.gov (United States)

1999-11-01

This volume contains the forst part of the author's PhD dissertation, and includes an introductory overview as well as two essays. The first essay entitled "The barely revealed preference behind road investment priorities," co-authored by Rune Elvik,...

Is road safety management linked to road safety performance?

Science.gov (United States)

Papadimitriou, Eleonora; Yannis, George

2013-10-01

This research aims to explore the relationship between road safety management and road safety performance at country level. For that purpose, an appropriate theoretical framework is selected, namely the 'SUNflower' pyramid, which describes road safety management systems in terms of a five-level hierarchy: (i) structure and culture, (ii) programmes and measures, (iii) 'intermediate' outcomes'--safety performance indicators (SPIs), (iv) final outcomes--fatalities and injuries, and (v) social costs. For each layer of the pyramid, a composite indicator is implemented, on the basis of data for 30 European countries. Especially as regards road safety management indicators, these are estimated on the basis of Categorical Principal Component Analysis upon the responses of a dedicated road safety management questionnaire, jointly created and dispatched by the ETSC/PIN group and the 'DaCoTA' research project. Then, quasi-Poisson models and Beta regression models are developed for linking road safety management indicators and other indicators (i.e. background characteristics, SPIs) with road safety performance. In this context, different indicators of road safety performance are explored: mortality and fatality rates, percentage reduction in fatalities over a given period, a composite indicator of road safety final outcomes, and a composite indicator of 'intermediate' outcomes (SPIs). The results of the analyses suggest that road safety management can be described on the basis of three composite indicators: "vision and strategy", "budget, evaluation and reporting", and "measurement of road user attitudes and behaviours". Moreover, no direct statistical relationship could be established between road safety management indicators and final outcomes. However, a statistical relationship was found between road safety management and 'intermediate' outcomes, which were in turn found to affect 'final' outcomes, confirming the SUNflower approach on the consecutive effect of each layer

Road Traffic Accident Variations in Lagos State, Nigeria: A Synopsis ...

African Journals Online (AJOL)

FIRST LADY

The major objective of this research is to examine the variation patterns of road traffic .... situation in Lagos state is bad because of the absence of effective transport ... environment as judged by the investigating officers. Also .... pattern of road traffic accident occurrence over that part of Lagos State. For ... Ph.D Thesis.

Technical regulations for road transport of radioactive materials

International Nuclear Information System (INIS)

Juul-Jensen, P.; Ulbak, K.

1990-01-01

The technical regulations for the transport of radioactive materials in Denmark are set down by the (Danish) National Board of Health in collaboration with the (Danish) National Institute for Radiation Hygiene in accordance with paragraph 3 of the Danish Ministry of Justice's Executive Order no. 2 of 2, January 1985 on the national road transport of dangerous goods by road, as amended by exutive order no. 251 of April 29th 1987 and no. 704 of November 1989. These regulations are presented here. They are almost identical, with only very few exceptions indicated in the publication, with the rules for Class 7 of the European convention on international transport of dangerous goods by road (ADR). In addition to the aforementioned regulations for national road transport of radioactive materials the general rules for the transport of radioactive materials found in the National Board of Health's executive order no. 721 of November 27th 1989 on the transport of radioactive materials are valid. The abovementioned executive orders, with the exception of certain supplements which are not part of the technical regulations, are also contained in this publication. (AB)

Forest road and fuel break siting with respect to reference fire intensities

Energy Technology Data Exchange (ETDEWEB)

Eastaugh, C. S.; Molina, D. M.

2012-11-01

Forest roads and permanent fuel breaks are an important part of fire suppression infrastructure, but due to maintenance and environmental costs many forest agencies seek to reduce the extent of these networks. The question of which roads should be retained or where fuel breaks should be established is contentious, and few quantified methods exist to aid management decisions. This study uses GIS procedures and develops a metric for road network vulnerability, which may be used to determine the relative effectiveness of a road network or a particular fuel break as a fire control line. The method constructs reference fire intensities, and compares the fire intensity at roadsides or fuel breaks with the overall forest average. In the case study area in Victoria's Central Highlands (southeast Australia), average fire intensities on the forest road network are found to closely match the forest average, indicating that roads in their current locations are not skewed towards more dangerous parts of the forest. The fuel break network however is likely to face fire intensities substantially greater than those in the average forest area. (Author) 33 refs.

Tire-road noise: an experimental study of tire and road design parameters

NARCIS (Netherlands)

Bekke, Dirk; Wijnant, Ysbrand H.; Weegerink, Thijs; de Boer, Andries

2013-01-01

It is widely known that road traffic noise has negative influences on human health. Hence, as tire-road noise is considered to be the most dominant cause of road traffic noise above 30-50 km/h, a lot of research is performed by the two involving industries: road authorities/manufacturers and tire

Distributed road assessment system

Science.gov (United States)

Beer, N. Reginald; Paglieroni, David W

2014-03-25

A system that detects damage on or below the surface of a paved structure or pavement is provided. A distributed road assessment system includes road assessment pods and a road assessment server. Each road assessment pod includes a ground-penetrating radar antenna array and a detection system that detects road damage from the return signals as the vehicle on which the pod is mounted travels down a road. Each road assessment pod transmits to the road assessment server occurrence information describing each occurrence of road damage that is newly detected on a current scan of a road. The road assessment server maintains a road damage database of occurrence information describing the previously detected occurrences of road damage. After the road assessment server receives occurrence information for newly detected occurrences of road damage for a portion of a road, the road assessment server determines which newly detected occurrences correspond to which previously detected occurrences of road damage.

Demonstrating a correlation between the maturity of road safety practices and road safety incidents.

Science.gov (United States)

Amador, Luis; Willis, Christopher Joseph

2014-01-01

The objective of this study is to demonstrate a correlation between the maturity of a country's road safety practices and road safety incidents. Firstly, data on a number of road injuries and fatalities for 129 countries were extracted from the United Nations Global Status on Road Safety database. These data were subdivided according to road safety incident and accident causation factors and normalized based on vehicular fleet (per 1000 vehicles) and road network (per meter of paved road). Secondly, a road safety maturity model was developed based on an adaptation of the concept of process maturity modeling. The maturity of countries with respect to 10 road safety practices was determined through the identification of indicators recorded in the United Nations Global Status of Road Safety Database. Plots of normalized road safety performance of the 129 countries against their maturity scores for each road safety practice as well as an aggregation of the road safety practices were developed. An analysis of variance was done to determine the extent of the correlation between the road safety maturity of the countries and their performance. In addition, a full Bayesian analysis was done to confirm the correlation of each of the road safety practices with injuries and fatalities. Regression analysis for fatalities, injuries, and combined accidents identified maturity with respect to road safety practices associated with speed limits and use of alternative modes as being the most significant predictors of traffic fatalities. A full Bayesian regression confirms that there is a correlation between the maturity of road safety practices and road safety incidents. Road safety practices associated with enforcement of speed limits and promotion of alternative modes are the most significant road safety practices toward which mature countries have concentrated their efforts, resulting in a lower frequency of fatalities, injury rates, and property damage accidents. The authors

Comparison of requirements for location, maintenance and removal of road advertising between polish and foreign regulations

Directory of Open Access Journals (Sweden)

Żukowska Joanna

2017-01-01

Full Text Available The article gives an overview of Polish and international formal and legal requirements for roadside advertising and the relevant road safety impacts. The analysis focussed on outdoor advertising life cycle consisting of three stages: location, operation and removal of advertising. Experience of road authorities from Australia (Queensland, Republic of South Africa and the United Kingdom was collected. The article is part of a joint project “Development of Road Innovations” funded by the National Centre for Development and Innovation and the General Directorate For National Roads and Motorways.

Policy Pathways: Improving the Fuel Economy of Road Vehicles - A policy package

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

The transportation sector accounts for approximately one-fifth of global final energy consumption and will account for nearly all future growth in oil use, particularly for road vehicles. The right policy mix can allow countries to improve the fuel economy of road vehicles, which in turn can enhance energy security and reduce CO2 emissions. Improving the Fuel Economy of Road Vehicles highlights lessons learned and examples of good practices from countries with experience in implementing fuel economy policies for vehicles. The report, part of the IEA’s Policy Pathway series, outlines key steps in planning, implementation, monitoring and evaluation. It complements the IEA Technology Roadmap: Fuel Economy for Road Vehicles, which outlines technical options, potentials, and costs towards improvement in the near, medium and long term.

Road traffic injury on rural roads in Tanzania: measuring the effectiveness of a road safety program.

Science.gov (United States)

Zimmerman, Karen; Jinadasa, Deepani; Maegga, Bertha; Guerrero, Alejandro

2015-01-01

Road traffic injuries (RTIs) are a major public health burden, especially in low- and middle-income countries. There is limited data on RTIs in low-volume, rural African settings. This study attempted to survey all individuals living in households within 200 m of two low-volume rural roads in Tanzania and to collect data on RTIs. Local communities and users of the Bago to Talawanda road (intervention site) and Kikaro to Mihuga road (control site) were targeted and received an intensive program of road safety measures tailored using the crash characteristics of the baseline sample. Demographic data on all household members were collected, and those individuals who suffered an RTI in the previous 3 months had comprehensive information collected about the crash characteristics and the socioeconomic impact. The follow-up data collection occurred nine months after the baseline data were collected. The majority of crashes that caused an RTI involved a motorcycle (71%) and the majority of victims were male (82%) with an average age of 27. Injuries to the legs (55%) were most common and the average length of time away from normal activity was 27 (±33) days. RTI incidence at the intervention site increased during the course of the study (incidence before vs. incidence after) and was unchanged in the community control (incidence before vs. incidence after). The incidence of RTIs in the low-volume rural setting is unacceptably high and most commonly associated with motorcycles. The change in incidence is unreliable due to logistic restraints of the project and more research is needed to quantify the impact of various RTI prevention strategies in this setting. This study provides insight into road traffic injuries on low-volume rural roads, areas where very little research has been captured. Additionally, it provides a replicable study design for those interested in collecting similar data on low-volume rural roads.

Road structural elements temperature trends diagnostics using sensory system of own design

Science.gov (United States)

Dudak, Juraj; Gaspar, Gabriel; Sedivy, Stefan; Pepucha, Lubomir; Florkova, Zuzana

2017-09-01

A considerable funds is spent for the roads maintenance in large areas during the winter. The road maintenance is significantly affected by the temperature change of the road structure. In remote locations may occur a situation, when it is not clear whether the sanding is actually needed because the lack of information on road conditions. In these cases, the actual road conditions are investigated by a personal inspection or by sending out a gritting vehicle. Here, however, is a risk of unnecessary trip the sanding vehicle. This situation is economically and environmentally unfavorable. The proposed system solves the problem of measuring the temperature profile of the road and the utilization of the predictive model to determine the future development trend of temperature. The system was technically designed as a set of sensors to monitor environmental values such as the temperature of the road, ambient temperature, relative air humidity, solar radiation and atmospheric pressure at the measuring point. An important part of the proposal is prediction model which based on the inputs from sensors and historical measurements can, with some probability, predict temperature trends at the measuring point. The proposed system addresses the economic and environmental aspects of winter road maintenance.

Quarry Haul Road Ecological Survey

International Nuclear Information System (INIS)

1992-09-01

This biological survey was performed to document the summer flora and fauna found along the haul road constructed as part of the remedial action for the quarry bulk waste. State and Federal species listed as threatened or endangered were noted if encountered while surveying. Sampling locations were equally spaced along the quarry haul road, and a survey for vegetation and birds conducted at each location. Bird observations were conducted as breeding bird surveys once in June of 1991, and again in June of 1992. Each year's survey includes two observations in the early morning and one late in the evening. Vegetation surveys were conducted in 1991 using quadrants and transects. mammal, reptile, and amphibian sightings were noted as encountered

AN INVESTIGATION ON THE FOREST ROAD PLANNING AND ROAD GROUND

Directory of Open Access Journals (Sweden)

Hafız Hulusi ACAR

2001-01-01

Full Text Available It is required that the capital used for construction of road must be technical, economical and used in its location. For this reason, the projects must be prepared for forest roads and all operations belong to roads must be guided according to these projects. In this investigation, available forest road network plan and constructed forest roads were investigated at the point of view technical and forest transportation. After this, it were studied to reach the highest exploitation rate as can as possible. Available forest road density were found as 11.9 m/ha in forest areas for Yesiltepe District. In this condition, exploitation rate was 78 %. After that, optimum forest road network were planned and road density were reached to 22 m/ha and exploitation rate to 86 %. Directed sample method were used from taking soil sample methods and samples were took in mixed system. According to results of the experiments, available forest roads were found in a good degree at the point of view endurance, pressing and transportation capacity. With these results, it is aimed to reach higher exploitation rate with given attention to landslide areas during planning of forest roads on the mountain areas such as Black Sea Region. For this reason, required importance must be given to planning of truck and logging roads. Ground analysis must be done and took care before during planning process of forest road network.

Construction of Three-Dimensional Road Surface and Application on Interaction between Vehicle and Road

Directory of Open Access Journals (Sweden)

Lu Yongjie

2018-01-01

Full Text Available The quantitative description is given to three-dimensional micro and macro self-similar characteristics of road surface from the perspective of fractal geometry using FBM stochastic midpoint displacement and diamond-square algorithm in conjunction with fractal characteristics and statistical characteristics of standard pavement determined by estimation method of box-counting dimension. The comparative analysis between reconstructed three-dimensional road surface spectrum and theoretical road surface spectrum and correlation coefficient demonstrate the high reconstruction accuracy of fractal reconstructed road spectrum. Furthermore, the bump zone is taken as an example to reconstruct a more arbitrary 3D road model through isomorphism of special road surface with stochastic road surface model. Measurement is taken to assume the tire footprint on road surface to be a rectangle, where the pressure distribution is expressed with mean stiffness, while the contact points in the contact area are replaced with a number of springs. Two-DOF vehicle is used as an example to analyze the difference between three-dimensional multipoint-and-plane contact and traditional point contact model. Three-dimensional road surface spectrum provides a more accurate description of the impact effect of tire on road surface, thereby laying a theoretical basis for studies on the dynamical process of interaction of vehicle-road surface and the road friendliness.

ENHANCEMENT OF ROAD SAFETY THROUGH MORE EFFECTIVE ROAD AND TRAFFIC MANAGEMENT

Directory of Open Access Journals (Sweden)

Tomasz SZCZURASZEK

2016-07-01

Full Text Available To make the policy aimed at mitigating the risk of road incidents more effective, Poland should see the introduction of the more efficient road and traffic management. In November 2008 the European Parliament and the European Council published the Directive on "infrastructure safety management" which provides guidance on the procedures for carrying impact assessments of traffic safety, traffic safety audits, safety management on the road network and monitoring traffic safety in Member States. In this article, the authors have proposed a systemic approach to road and traffic management, involving the implementation of consistent procedures that should include regular revisions of roads, eliminating hazardous sites, speed management, as well as the approval and implementation of traffic organization designs.

Miscellaneous Roads

Data.gov (United States)

Minnesota Department of Natural Resources — This data set contains roadway centerlines for miscellanous roads, a catch-all category for all road types not present in the other DNR derived products. These road...

Invasive Brown Treesnake movements at road edges indicate road-crossing avoidance

Science.gov (United States)

Siers, Shane R.; Savidge, Julie S; Reed, Robert N.

2014-01-01

Roads have significant impacts on the dispersal of wildlife. Although this poses a threat to the abundance and diversity of desirable flora and fauna, it also affords some opportunity for enhancing control of invasive species. Roads are the most common terrain features that may affect the rate of landscape-scale movements of invasive Brown Treesnakes (Boiga irregularis) throughout Guam. We radio tracked 45 free-ranging Brown Treesnakes in close proximity to two roads in Guam and recorded instances where daily relocations of snakes spanned roads. Then we reconstructed observed movement histories with randomized turning angles, which served as a useful null hypothesis for assessing the effect of roads or road edge habitat on Brown Treesnake movement patterns. Random walk simulations demonstrated that Brown Treesnakes crossed these roads at a rate far lower than would be expected if snake movement was random with respect to roads and road edge habitat. We discuss two alternative hypotheses for these results: 1) habitat gaps posed by roads physically or behaviorally restrict snake movement; or 2) road edges provide preferred foraging habitat from which snakes are reluctant to depart. Because roads often form the boundaries of jurisdictional and management units, the effects of roads on the movement of invasive Brown Treesnakes will influence the prospects for success of future landscape-level suppression efforts.

The road maintenance funding models in Indonesia use earmarked tax

Science.gov (United States)

Gultom, Tiopan Henry M.; Tamin, Ofyar Z.; Sjafruddin, Ade; Pradono

2017-11-01

One of the solutions to get a sustainable road maintenance fund is to separate road sector revenue from other accounts, afterward, form a specific account for road maintenance. In 2001, Antameng and the Ministry of Public Works proposed a road fund model in Indonesia. Sources of the road funds proposal was a tariff formed on the nominal total tax. The policy of road funds was proposed to finance the road network maintenance of districts and provincials. This research aims to create a policy model of road maintenance funds in Indonesia using an earmarked tax mechanism. The research method is qualitative research, with data collection techniques are triangulation. Interview methods conducted were semi-structured. Strength, Weakness, Opportunities, and Threat from every part of the models were showen on the survey format. Respondents were representative of executives who involved directly against the financing of road maintenance. Validation model conducted by a discussion panel, it was called the Focus Group Discussion (FGD). The FGD involved all selected respondents. Road maintenance financing model that most appropriately applied in Indonesia was a model of revenue source use an earmarked PBBKB, PKB and PPnBM. Revenue collection mechanism was added tariff of registered vehicle tax (PKB), Vehicle Fuel Tax (PBBKB) and the luxury vehicle sales tax (PPnBM). The funds are managed at the provincial level by a public service agency.

Planning and Arun's (not so straight and narrow) roads | van Wyk ...

African Journals Online (AJOL)

Arun Property Development (Pty) Ltd wished to subdivide portions of the farm Langeberg 311, Durbanville. The 1988 structure plan for the area had indicated that certain roads would traverse the property. These and other roads all formed part of a new subdivision known as Sonstraal Heights. As is customary, the ...

Density and diversity of OpenStreetMap road networks in China

Directory of Open Access Journals (Sweden)

Yingjia Zhang

2015-12-01

Full Text Available OpenStreetMap is a geographic information platform designed to provide real-time updates and user-generated content related to its freely available global map, and it is one of the most widely used examples of volunteered geographic information, a technique associated with so-called neogeography. This paper, based on the data from China’s OpenStreetMap road network in May 2014, taking 340 prefecture-level cities in China as its study area, presents the geometric-related (road density and attribute-related (type diversity spatial patterns of the OpenStreetMap road network, and explores their relationship. The results are as follows. (1 The distribution of OpenStreetMap road density in Shenzhen, Shanghai, Hong Kong, and Macao predominantly obeys a “positive skewness distribution”. OpenStreetMap data for eastern China shows a higher overall and circular structure. In central China, there are noticeable discrepancies in the road density, whereas in western China, the road density is low. (2 The OpenStreetMap road diversity shows a normal distribution. The spatial pattern for the so-called “Hu Huanyong line” was broken by the effect of diplomatic and strategic factors, showing a high diversity along the peripheral border, coastal cities, and core inland cites. (3 China’s OpenStreetMap is partitioned into four parts according to road density and diversity: high density and high diversity; low density and low diversity; high density and low diversity; and low density high diversity. (4 The OpenStreetMap geographical information-collection process and mechanism were analyzed, demonstrating that the road density reflects the preponderance of traffic in the real world. OpenStreetMap road diversity reflects the road-related geographic information demand and value, and it also reflects the interests of users toward to OpenStreetMap geographical information.

Roads Rehabilitation and Environment in Moldova: Some Legal and Normative Harmonization Aspects

Directory of Open Access Journals (Sweden)

Cocirta Petru

2014-05-01

Full Text Available This paper analyzes the environmental regulatory reforms of the Republic of Moldova to restore roads and problems over time. Goals and objectives are the analysis of the current situation on road rehabilitation and environmental assessments in this area, as well as issues that require in rehabilitation and maintenance of roads in the Republic of Moldova.Are described briefly: general aspects of road rehabilitation issues; legislation and environmental regulations in the road; differences between Moldova and procedures of the World Bank's environmental assessment in the construction and rehabilitation of roads; problem of national legislative and normative acts harmonization to international requirements.The paper discusses specific environmental to appear on completion of the rehabilitation of roads in the Republic of Moldova. In the final part of the paper presents the conclusions and some suggestions on how to facilitate the rehabilitation of roads in accordance with Agenda 21 of the country and European and international requirements.

Visibility of road markings on wet road surfaces : a literature study.

NARCIS (Netherlands)

Schreuder, D.A.

1981-01-01

The English version of B 14153 is presented. Road markings, notably lane markers, are often only poorly visible when the road is wet. This is particularly a problem at night on unlit roads. A study is made of whether a solution for this problem can be found on the basis of the known, published

Infrastructure design & road safety : OECD Workshop B3 (Infrastructure design and road safety) for CEE's and NIS held on 15th-18th November 1994, Prague (Czech Republic). Part 2: Lectures.

NARCIS (Netherlands)

2012-01-01

The workshop 'Infrastructure design and road safety ' was one of the initiatives which the OECO Steering Committee for Road Transport Research developed with the aim of exchanging information in the road transport sector, in order to respond to the urgent needs expressed by Central and Eastern

Characteristics of public roads operation

OpenAIRE

Pryimak, V.; Kyiashko, I.

2009-01-01

Characteristics of public roads operation have been considered and factors influencing TEC of public roads that go via urban areas have been determined. There have been revealed contradictions in the normative-legal base concerning maintenance of public roads and municipal roads that merge into them.

Risk Analysis in Road Tunnels – Most Important Risk Indicators

DEFF Research Database (Denmark)

Berchtold, Florian; Knaust, Christian; Thöns, Sebastian

2016-01-01

Methodologies on fire risk analysis in road tunnels consider numerous factors affecting risks (risk indicators) and express the results by risk measures. But only few comprehensive studies on effects of risk indicators on risk measures are available. For this reason, this study quantifies...... the effects and highlights the most important risk indicators with the aim to support further developments in risk analysis. Therefore, a system model of a road tunnel was developed to determine the risk measures. The system model can be divided into three parts: the fire part connected to the fire model Fire...... Dynamics Simulator (FDS); the evacuation part connected to the evacuation model FDS+Evac; and the frequency part connected to a model to calculate the frequency of fires. This study shows that the parts of the system model (and their most important risk indicators) affect the risk measures in the following...

Road Service Performance Based On Integrated Road Design Consistency (IC) Along Federal Road F0023

OpenAIRE

Zainal Zaffan Farhana; Prasetijo Joewono; Musa Wan Zahidah

2017-01-01

Road accidents are one of the world’s largest public health and injury prevention problems. In Malaysia, the west coast area of Malaysia been stated as the highest motorcycle fatalities and road accidents are one of the factors that cause of death and injuries in this country. The most common fatal accident is between a motorcycle and passenger car. The most of the fatal accidents happened on Federal roads with 44 fatal accidents reported, which is equal to 29%. Lacks of road geometric design...

Explaining the road accident risk: weather effects.

Science.gov (United States)

Bergel-Hayat, Ruth; Debbarh, Mohammed; Antoniou, Constantinos; Yannis, George

2013-11-01

This research aims to highlight the link between weather conditions and road accident risk at an aggregate level and on a monthly basis, in order to improve road safety monitoring at a national level. It is based on some case studies carried out in Work Package 7 on "Data analysis and synthesis" of the EU-FP6 project "SafetyNet-Building the European Road Safety Observatory", which illustrate the use of weather variables for analysing changes in the number of road injury accidents. Time series analysis models with explanatory variables that measure the weather quantitatively were used and applied to aggregate datasets of injury accidents for France, the Netherlands and the Athens region, over periods of more than 20 years. The main results reveal significant correlations on a monthly basis between weather variables and the aggregate number of injury accidents, but the magnitude and even the sign of these correlations vary according to the type of road (motorways, rural roads or urban roads). Moreover, in the case of the interurban network in France, it appears that the rainfall effect is mainly direct on motorways--exposure being unchanged, and partly indirect on main roads--as a result of changes in exposure. Additional results obtained on a daily basis for the Athens region indicate that capturing the within-the-month variability of the weather variables and including it in a monthly model highlights the effects of extreme weather. Such findings are consistent with previous results obtained for France using a similar approach, with the exception of the negative correlation between precipitation and the number of injury accidents found for the Athens region, which is further investigated. The outlook for the approach and its added value are discussed in the conclusion. Copyright © 2013. Published by Elsevier Ltd.

Road analysis: a tool for cost-effective rehabilitation measures for Finnish roads

Science.gov (United States)

Roimela, Petri; Salmenkaita, Seppo; Maijala, Pekka; Saarenketo, Timo

2000-04-01

Public funding for road network maintenance has decreased 30% during the last few years in Finland. Reduced resources, together with the current rehabilitation strategies, will in the long term result in increasing deterioration of the Finnish road network. For this reason road rehabilitation funding should be focused more specifically on those roads and road sections requiring measures and these measures should be optimized to ensure that only the specific problem structure will be repaired. Roadscanners Oy, in cooperation with the Finnish National Road Administration (Finnra), has developed a new and effective Road Analysis technique to survey the condition of roads and road networks. Road Analysis is based on the integrated analysis of the measured data collected from the road under survey. The basic survey methods used in Road Analysis include Ground Penetrating Data (GPR), falling weight deflectometer (FWD), roughness and rutting measurements, pavement distress mapping and GPS-positioning, as well as reference drilling based on preliminary GPR data analysis. The collected road survey data is processed, interpreted, analyzed and classified using Road Doctor software, specifically developed for this purpose. GPR measurements in road analysis are carried out using a 400 MHz ground-coupled antenna and a 1.0 GHz horn antenna. Horn antenna data is used to measure the thickness of the pavement and base course layers, as well as to evaluate their quality based on their dielectric properties. The 400 MHz ground-coupled data is used to estimate the thickness of the pavement structure and embankment. Ground-coupled antenna data is used for subgrade quality estimations and in evaluating the causes of subgrade- related frost defects. GPR data also provides important location information about special structures, such as steel reinforcements, cables and pipelines. Road Analysis includes a classification of the critical elements affecting the lifetime of the road: (1

Wildlife friendly roads: the impacts of roads on wildlife in urban areas and potential remedies

Science.gov (United States)

Riley, Seth P D; Brown, Justin L.; Sikich, Jeff A.; Schoonmaker, Catherine M.; Boydston, Erin E.

2014-01-01

Roads are one of the most important factors affecting the ability of wildlife to live and move within an urban area. Roads physically replace wildlife habitat and often reduce habitat quality nearby, fragment the remaining habitat, and cause increased mortality through vehicle collisions. Much ecological research on roads has focused on whether animals are successfully crossing roads, or if the road is a barrier to wildlife movement, gene flow, or functional connectivity. Roads can alter survival and reproduction for wildlife, even among species such as birds that cross roads easily. Here we examine the suite of potential impacts of roads on wildlife, but we focus particularly on urban settings. We report on studies, both in the literature and from our own experience, that have addressed wildlife and roads in urban landscapes. Although road ecology is a growing field of study, relatively little of this research, and relatively few mitigation projects, have been done in urban landscapes. We also draw from the available science on road impacts in rural areas when urban case studies have not fully addressed key topics.

Predictability by recognizable road design. [previously called: Recognizable road design.

NARCIS (Netherlands)

2007-01-01

One of the Sustainable Safety principles is that a road should have a recognizable design and a predictable alignment. If this is the case, road users know how they are expected to behave and what they can expect from other road users, so that crashes may be prevented. For roads to be recognizable,

Challenges of raising road maintenance funds in developing countries: An analysis of road tolling in Zimbabwe

Directory of Open Access Journals (Sweden)

T. C. Mbara

2010-11-01

Full Text Available The condition of Zimbabwe's roads has been declining due to insufficient maintenance and rehabilitation. Year on year, budget allocations have compared unfavourably with funding considered adequate to maintain highway networks and conduct modest construction work. Road infrastructure shortcomings have manifested themselves in the form of high vehicle operating costs and rampant potholes, leading to a decline in road safety and a deterioration of service levels for those who use roads to deliver goods or connect to international markets. In order to try and stop this vicious cycle of decline, the Government of Zimbabwe, on 8 August 2009, introduced a new policy of road-user charges, which involved the setting-up of 22 toll gates on the trunk road network. The overall objective was to raise revenue in order to close the funding gap, blamed for declining road quality. Although alternative methods of financing road maintenance have been debated for years, a generally accepted understanding is that road users should pay costs for road provisioning. This paper assesses the implementation of a road tolling system in Zimbabwe and describes matters relating to, inter alia, implementation strategy, initial performance outcomes and sustainability.

Road Service Performance Based On Integrated Road Design Consistency (IC Along Federal Road F0023

Directory of Open Access Journals (Sweden)

Zainal Zaffan Farhana

2017-01-01

Full Text Available Road accidents are one of the world’s largest public health and injury prevention problems. In Malaysia, the west coast area of Malaysia been stated as the highest motorcycle fatalities and road accidents are one of the factors that cause of death and injuries in this country. The most common fatal accident is between a motorcycle and passenger car. The most of the fatal accidents happened on Federal roads with 44 fatal accidents reported, which is equal to 29%. Lacks of road geometric designs consistency where the drivers make mistakes errors due to the road geometric features causes the accident kept rising in Malaysia. Hence, models are based on operating speed to calculate design consistency of road. The profiles were obtained by continuous speed profile using GPS data. The continuous operating speed profile models were plotted based on operating speed model (85th percentile. The study was conduct at F0023 from km 16 until km 20. The purpose of design consistency is to know the relationship between the operating speed and elements of geometric design on the road. As a result, the integrated design consistency motorcycle and cars along a segment at F0023, the threshold shows poor design quality for motorcycles and cars.

CFD analysis for road vehicles - case study

Directory of Open Access Journals (Sweden)

Eugen Mihai NEGRUS

2011-09-01

Full Text Available This is a case study on the influence of the lower part of road vehicles on the global drag characteristics. Reducing overall drag by redesigning the lower part of the road vehicles has a potential of almost 20% in the overall drag breakdown, mainly due to the viscous effects and the fluidic interaction of the flow under the car with the typical bluff body flow pattern behind the vehicle. A special parameterization is proposed for the global shape of the sedan car, with respect to the lower part of the body, taking into account most of the specificities of the system. For such a complex interaction, CFD analysis is probably the only efficient tool in order to assess specific design parameterization of a generic car shape. Building on the credibility of such instruments is one of the major goals of this paper. Also, with respect to a target sedan car configuration, examples of successful design strategies are presented. Based on the CFD results, possible strategies to be used in order to reduce viscous drag and global drag characteristics are proposed.

Performance standards of road safety management

Directory of Open Access Journals (Sweden)

Čabarkapa Milenko R.

2016-01-01

Full Text Available Road safety management controlling means the process of finding out the information whether the road safety is improving in a measure to achieve the objectives. The process of control consists of three basic elements: definition of performances and standards, measurement of current performances and comparison with the set standards, and improvement of current performances, if they deviate from the set standards. The performance standards of road safety management system are focused on a performances measurement, in terms of their design and characteristics, in order to support the performances improvement of road safety system and thus, ultimately, improve the road safety. Defining the performance standards of road safety management system, except that determines the design of the system for performances measurement, directly sets requirements whose fulfillment will produce a road safety improvement. The road safety management system, based on the performance standards of road safety, with a focus on results, will produce the continuous improvement of road safety, achieving the long-term 'vision zero', the philosophy of road safety, that human life and health take priority over mobility and other traffic objectives of the road traffic.

Road Tax in the Czech Republic during the Period 1993 – 2011

Directory of Open Access Journals (Sweden)

ANDRLÍK

2013-02-01

Full Text Available The paper provides descriptive analysis of the road tax performance in the CR in connection to relevant legal amendments to the Act No. 16/1993 Coll. Data on road tax from 1993 to 2011 were used in this analysis and are available from the Ministry of Finance of the Czech Republic. Road tax in the Czech Republic represents only a small part of the total tax revenue and its collection provides insufficient funds for maintenance and development of road infrastructure in the Czech Republic. Road tax collection is expected to grow in the future as a result of ongoing replacement and modernization of vehicle fleet, growing number of vehicles, strengthening of environmental aspects of taxes and internalisation of costs of transport.

How effective is road mitigation at reducing road-kill? A meta-analysis

NARCIS (Netherlands)

Rytwinski, Trina; Soanes, Kylie; Jaeger, Jochen A.G.; Fahrig, Lenore; Findlay, C.S.; Houlahan, Jeff; Ree, van der Rodney; Grift, van der Edgar A.

2016-01-01

Road traffic kills hundreds of millions of animals every year, posing a critical threat to the populations of many species. To address this problem there are more than forty types of road mitigation measures available that aim to reduce wildlife mortality on roads (road-kill). For road planners,

Road safety campaign is a great success

CERN Multimedia

2008-01-01

Rolf Heuer, the next Director-General of CERN, and Sigurd Lettow, the Director of Finance and Human Resources (photo below), completed all the tests of the CERN road safety campaign under the supervision of TCS instructors. The road safety campaign, which took place in the Main Building during the week of 10 November, attracted large numbers of participants. More than 300 CERN personnel and users took part in, and in some cases were literally bowled over by, the activities set up by instructors from the TCS (Touring Club Suisse). The campaign’s aim was to raise driver awareness of several aspects of road safety, including speed, use of mobile phones at the wheel, pedestrian priority, unlawful parking and driving with a valid licence. The campaign was an unqualified success! Even CERN’s directors joined in, testing their own reactions as drivers on the various pieces of apparatus in place.

Joint road safety operations in tunnels and open roads

Science.gov (United States)

Adesiyun, Adewole; Avenoso, Antonio; Dionelis, Kallistratos; Cela, Liljana; Nicodème, Christophe; Goger, Thierry; Polidori, Carlo

2017-09-01

The objective of the ECOROADS project is to overcome the barrier established by the formal interpretation of the two Directives 2008/96/EC and 2004/54/EC, which in practice do not allow the same Road Safety Audits/Inspections to be performed inside tunnels. The projects aims at the establishment of a common enhanced approach to road infrastructure and tunnel safety management by using the concepts and criteria of the Directive 2008/96/CE on road infrastructure safety management and the results of related European Commission (EC) funded projects. ECOROADS has already implemented an analysis of national practices regarding Road Safety Inspections (RSI), two Workshops with the stakeholders, and an exchange of best practices between European tunnel experts and road safety professionals, which led to the definition of common agreed safety procedures. In the second phase of the project, different groups of experts and observers applied the above common procedures by inspecting five European road sections featuring both open roads and tunnels in Belgium, Albania, Germany, Serbia and Former Yugoslav Republic of Macedonia. This paper shows the feedback of the 5 joint safety operations and how they are being used for a set of - recommendations and guidelines for the application of the RSA and RSI concepts within the tunnel safety operations.

The impact of road improvements on road safety and related characteristics

OpenAIRE

Francis John Gichaga

2017-01-01

This paper presents the historical and cultural background relating to road improvement and road safety characteristics in Kenya, a developing country in East Africa. Some who come from low-developed areas of developing countries often take time to comprehend the modern transportation infrastructure, especially roads, and have difficulty assimilating and customizing the same to their culturally tailored modes. This paper discusses two case studies: one on the socio-economic impact followin...

Payment mechanisms for winter road maintenance services

Directory of Open Access Journals (Sweden)

Adel Abdi

2013-12-01

Full Text Available In countries with severe winters a major part of the annual budget for road maintenance is allocated on performance of winter road maintenance tasks. Finding appropriate remuneration forms to compensate entrepreneurs for performed road measures during winter is not an easy task in order to minimise or eliminate disputes and satisfy both client organisations and contractors. On the other hand improper reimbursement models lead either to the client’s annual budget imbalance due to unnecessary cost overruns or affect contractor’s cash-flow. Such cases in turn affect just-in-time winter road maintenance and then traffic safety. To solve such problems, a number of countries in cold regions like Sweden have developed different remuneration models based more on weather data called Weather Index. Therefore the objective of this paper is to investigate and evaluate the payment models applied in Sweden. The study uses a number of approaches namely; domestic questionnaire survey, analysis of a number of contract documents, a series of meetings with the project managers and an international benchmarking. The study recognised four remuneration models for winter maintenance service of which one based on weather data statistics. The study reveals the payment model based on weather data statistics is only applied for the roads with higher traffic flow and the model generates most uncertainty.

Impact of different parts of unpaved forest roads on runoff and sediment yield in a Mediterranean area.

Science.gov (United States)

Jordán-López, Antonio; Martínez-Zavala, Lorena; Bellinfante, Nicolás

2009-01-01

Surface runoff and sediment production on unpaved forest roads in a humid Mediterranean mountainous area has been studied using a simple portable rainfall simulator at an intensity of 90 mm h(-1). Thirty six rainfall simulations were carried out on road plots: on the roadbank (12), on the sidecast fill (12), and on the roadbed (12). On the roadbanks, the steady-state runoff coefficient was 85.9% and runoff flow appeared after 63 s on average. On the sidecast fills, the steady-state runoff coefficient was 58.6% and mean time to runoff was 48 s. Finally, on the roadbeds, the steady-state runoff coefficient was 21.5% and mean time to runoff was 41 s. The highest soil loss rate was found on the roadbanks (486.7 g m(-2)), mainly due to low plant cover, soil texture and rock fragments. The total soil erosion on the roadbanks was 3 and 18 times higher than those from the roadbeds and the sidecast fills, respectively. As a consequence, roadbanks can be considered the main source of sediments on the studied sites, but the function of unpaved forest roads as source points for runoff generation is more important.

How Effective Is Road Mitigation at Reducing Road-Kill? A Meta-Analysis

OpenAIRE

Rytwinski, Trina; Soanes, Kylie; Jaeger, Jochen A. G.; Fahrig, Lenore; Findlay, C. Scott; Houlahan, Jeff; van der Ree, Rodney; van der Grift, Edgar A

2016-01-01

Road traffic kills hundreds of millions of animals every year, posing a critical threat to the populations of many species. To address this problem there are more than forty types of road mitigation measures available that aim to reduce wildlife mortality on roads (road-kill). For road planners, deciding on what mitigation method to use has been problematic because there is little good information about the relative effectiveness of these measures in reducing road-kill, and the costs of these...

How Effective Is Road Mitigation at Reducing Road-Kill? A Meta-Analysis.

Science.gov (United States)

Rytwinski, Trina; Soanes, Kylie; Jaeger, Jochen A G; Fahrig, Lenore; Findlay, C Scott; Houlahan, Jeff; van der Ree, Rodney; van der Grift, Edgar A

2016-01-01

Road traffic kills hundreds of millions of animals every year, posing a critical threat to the populations of many species. To address this problem there are more than forty types of road mitigation measures available that aim to reduce wildlife mortality on roads (road-kill). For road planners, deciding on what mitigation method to use has been problematic because there is little good information about the relative effectiveness of these measures in reducing road-kill, and the costs of these measures vary greatly. We conducted a meta-analysis using data from 50 studies that quantified the relationship between road-kill and a mitigation measure designed to reduce road-kill. Overall, mitigation measures reduce road-kill by 40% compared to controls. Fences, with or without crossing structures, reduce road-kill by 54%. We found no detectable effect on road-kill of crossing structures without fencing. We found that comparatively expensive mitigation measures reduce large mammal road-kill much more than inexpensive measures. For example, the combination of fencing and crossing structures led to an 83% reduction in road-kill of large mammals, compared to a 57% reduction for animal detection systems, and only a 1% for wildlife reflectors. We suggest that inexpensive measures such as reflectors should not be used until and unless their effectiveness is tested using a high-quality experimental approach. Our meta-analysis also highlights the fact that there are insufficient data to answer many of the most pressing questions that road planners ask about the effectiveness of road mitigation measures, such as whether other less common mitigation measures (e.g., measures to reduce traffic volume and/or speed) reduce road mortality, or to what extent the attributes of crossing structures and fences influence their effectiveness. To improve evaluations of mitigation effectiveness, studies should incorporate data collection before the mitigation is applied, and we recommend a

How Effective Is Road Mitigation at Reducing Road-Kill? A Meta-Analysis.

Directory of Open Access Journals (Sweden)

Trina Rytwinski

Full Text Available Road traffic kills hundreds of millions of animals every year, posing a critical threat to the populations of many species. To address this problem there are more than forty types of road mitigation measures available that aim to reduce wildlife mortality on roads (road-kill. For road planners, deciding on what mitigation method to use has been problematic because there is little good information about the relative effectiveness of these measures in reducing road-kill, and the costs of these measures vary greatly. We conducted a meta-analysis using data from 50 studies that quantified the relationship between road-kill and a mitigation measure designed to reduce road-kill. Overall, mitigation measures reduce road-kill by 40% compared to controls. Fences, with or without crossing structures, reduce road-kill by 54%. We found no detectable effect on road-kill of crossing structures without fencing. We found that comparatively expensive mitigation measures reduce large mammal road-kill much more than inexpensive measures. For example, the combination of fencing and crossing structures led to an 83% reduction in road-kill of large mammals, compared to a 57% reduction for animal detection systems, and only a 1% for wildlife reflectors. We suggest that inexpensive measures such as reflectors should not be used until and unless their effectiveness is tested using a high-quality experimental approach. Our meta-analysis also highlights the fact that there are insufficient data to answer many of the most pressing questions that road planners ask about the effectiveness of road mitigation measures, such as whether other less common mitigation measures (e.g., measures to reduce traffic volume and/or speed reduce road mortality, or to what extent the attributes of crossing structures and fences influence their effectiveness. To improve evaluations of mitigation effectiveness, studies should incorporate data collection before the mitigation is applied, and we

How Effective Is Road Mitigation at Reducing Road-Kill? A Meta-Analysis

Science.gov (United States)

Rytwinski, Trina; Soanes, Kylie; Jaeger, Jochen A. G.; Fahrig, Lenore; Findlay, C. Scott; Houlahan, Jeff; van der Ree, Rodney; van der Grift, Edgar A

2016-01-01

Road traffic kills hundreds of millions of animals every year, posing a critical threat to the populations of many species. To address this problem there are more than forty types of road mitigation measures available that aim to reduce wildlife mortality on roads (road-kill). For road planners, deciding on what mitigation method to use has been problematic because there is little good information about the relative effectiveness of these measures in reducing road-kill, and the costs of these measures vary greatly. We conducted a meta-analysis using data from 50 studies that quantified the relationship between road-kill and a mitigation measure designed to reduce road-kill. Overall, mitigation measures reduce road-kill by 40% compared to controls. Fences, with or without crossing structures, reduce road-kill by 54%. We found no detectable effect on road-kill of crossing structures without fencing. We found that comparatively expensive mitigation measures reduce large mammal road-kill much more than inexpensive measures. For example, the combination of fencing and crossing structures led to an 83% reduction in road-kill of large mammals, compared to a 57% reduction for animal detection systems, and only a 1% for wildlife reflectors. We suggest that inexpensive measures such as reflectors should not be used until and unless their effectiveness is tested using a high-quality experimental approach. Our meta-analysis also highlights the fact that there are insufficient data to answer many of the most pressing questions that road planners ask about the effectiveness of road mitigation measures, such as whether other less common mitigation measures (e.g., measures to reduce traffic volume and/or speed) reduce road mortality, or to what extent the attributes of crossing structures and fences influence their effectiveness. To improve evaluations of mitigation effectiveness, studies should incorporate data collection before the mitigation is applied, and we recommend a

Automated vehicle location, data recording, friction measurement and applicator control for winter road maintenance.

Science.gov (United States)

2010-02-01

The first part of this project conducted a detailed evaluation of the ability of a new friction measurement system to : provide an accurate measure of road conditions. A system that records friction coefficient as a function of road : location was de...

Road Network Selection Based on Road Hierarchical Structure Control

Directory of Open Access Journals (Sweden)

HE Haiwei

2015-04-01

Full Text Available A new road network selection method based on hierarchical structure is studied. Firstly, road network is built as strokes which are then classified into hierarchical collections according to the criteria of betweenness centrality value (BC value. Secondly, the hierarchical structure of the strokes is enhanced using structural characteristic identification technique. Thirdly, the importance calculation model was established according to the relationships among the hierarchical structure of the strokes. Finally, the importance values of strokes are got supported with the model's hierarchical calculation, and with which the road network is selected. Tests are done to verify the advantage of this method by comparing it with other common stroke-oriented methods using three kinds of typical road network data. Comparision of the results show that this method had few need to semantic data, and could eliminate the negative influence of edge strokes caused by the criteria of BC value well. So, it is better to maintain the global hierarchical structure of road network, and suitable to meet with the selection of various kinds of road network at the same time.

Comparing Environmental Impact Assessment (EIA) in Poland and Denmark for Road Construction in Relation to Wildlife and Nature Protection : Synopsis

DEFF Research Database (Denmark)

Sienkiewicz, J.; Briggs, L; Elmeros, M.

Project : Fauna Passages under Selected Roads in Poland - Education, Monitoring and Construction - Part A.......Project : Fauna Passages under Selected Roads in Poland - Education, Monitoring and Construction - Part A....

Priority of road maintenance management based on halda reading range on NAASRA method

Science.gov (United States)

Surbakti, M.; Doan, A.

2018-02-01

The road pavement, constantly experiencing stress-strain due to traffic load through it, can cause damage to the pavement. Therefore, early detection and repair of the damage will be able to prevent more severe damage that can develop into pavement failure. A road condition survey is one of the earliest attempts to detect the initial damage of a pavement. In this case the driving comfort is the most important part for the driver in assessing road conditions that are affected by the level of road surface roughness. To determine the level of roughness of the road, one of the methods developed is the measurement using the NAASRA method. In this method the roughness of the road is an accumulation of the average unevenness of the road, with the general setting on halda of 100 m. However, with this 100-meter setting, in some places the final value of the roughness value is too large or too small so that it will result in the priority of the road maintenance. This is what underlies roughness research by comparing halda settings at 50 m and 200 m different from the general settings above.This study uses the International Roughness Index (IRI) method in determining the level of road stability concerning driving discomfort. IRI score obtained from direct survey in field by using Roughometer-NAASRA.The final result shows that there is a significant difference between the reading of halda which is set at 100 m reading with halda set with 50 and 200 meter readings. This may lead to differences in handling priorities, which may impact on the sustainability of road network maintenance management (Sustainaible Road Management)

Road safety performance indicators for the interurban road network.

NARCIS (Netherlands)

Yannis, G. Weijermars, W.A.M. Gitelman, V. Vis, M. Chazirisa, A. Papadimitriou, E. & Lima Azevedo, C.

2013-01-01

Various road safety performance indicators (SPIs) have been proposed for different road safety research areas, mainly as regards driver behaviour (e.g. seat belt use, alcohol, drugs, etc.) and vehicles (e.g. passive safety); however, no SPIs for the road network and design have been developed. The

Epidemiologic study of road traffic injuries by road user type characteristics and road environment in Iran: a community-based approach.

Science.gov (United States)

Hatamabadi, Hamidreza; Vafaee, Reza; Hadadi, Mashyaneh; Abdalvand, Ali; Esnaashari, Hamidreza; Soori, Hamid

2012-01-01

Crash injuries in traffic accidents are affected by a variety of factors. In this study we analyzed road user type information based on different contributing factors. Data from all of the road traffic victims on a road extending from the east of the city of Tehran to Mazandaran province were included prospectively over a one-year period (May 2008 to May 2009). Data collected included the crash time, patient's age and sex, road user category, helmet or seat belt use, anatomical site of injury, Injury Severity Score (ISS), and mortality. Prevalence and cross-tabulations were included in the analysis. There were 433 patients, of whom 345 were hospitalized and 33 died either before or after arriving at the hospital. Sixty-nine percent of injured patients were vehicle occupants. Mean and median of ISS were higher for pedestrians, who accounted for 49 percent of the deaths. Head injury was the most common injury and injury to upper and lower extremities was the most common cause of admission. A significant difference in lower extremity injuries between vehicle occupants and nonoccupants was found. Sex and age group did not have a significant effect on mortality. Mortality was significantly higher in pedestrians (P road user type. Because pedestrians are the most vulnerable road users, stricter legislation and law enforcement should be used to protect them. Greater protection can also be reached by holding effective public awareness campaigns on how to use different roads safely. On the other hand, because rear seat passengers are at the same risk for road traffic injuries as front seat passengers, employment of newer laws and preventive measures targeting this group of occupants can prevent many road traffic injuries (RTIs).

Road pricing policy implementation

NARCIS (Netherlands)

Vonk Noordegraaf, D.M.

2016-01-01

Urban areas suffer from the negative externalities of road transport like congested road networks, air pollution and road traffic accidents. A measure to reduce these negative externalities is road pricing, meaning policies that impose direct charges on road use (Jones and Hervik, 1992). Since the

The impact of environment change on culture evolution in east Ancient Silk Road.

Science.gov (United States)

Dong, G.; Liu, F.; Li, G.; Zhang, D. D.; Lee, H. F.; Chen, F.

2017-12-01

Ancient Silk Road played an important role in culture communication between west and east parts of the Eurasia during Bronze Age and historical period. Tens of archaic civilizations rise and fall in east parts of the Ancient Silk Road, climate change is attributed as one of the most important driving forces, while the process and mechanism for the impact of environmental change on culture evolution in the area has not been well-understood. Here we report new paleoclimate data based on multi-proxy analysis from two well-dated aeolian deposit sequences in the Hexi Corridor and Qaidam basin, where locate at the throat position of the Ancient Silk Road. Comparing with high-resolution tree rings from Qilian Mountain nearby, and archaeological evidence and historical documents, we proposed that two desertification events occurred in west Hexi Corridor between 3400-3100 BP and post 1450 AD, which induced two cultural discontinuity in that area. Climate was dry between 3400-2900 BP and wet between 2900-2000 BP in lowlands of east Qaidam basin, mismatching with the development of Nuomuhong Bronze culture in the area during 3400-2450 BP. We propose culture evolution in east Ancient Silk Road was mainly influenced by precipitation change of highlands in mountain areas,which was further influenced by large-scale vapor transport.

Model simulation of Venezia-Mestre ring road air pollution: experimental check and model intercomparison

Energy Technology Data Exchange (ETDEWEB)

Biancotto, R.; Coraluppi, L.; Pistollato, S.; Rosa, M.; Tarabotti, E. [Veneto Region Environmental Protection Agency - Dept. of Venice, Mestre (Italy); Liguori, F.; Lorenzet, K.; Pillon, S. [Veneto Region Environmental Protection Agency - Regional Air Observatory, Mestre (Italy); Maffeis, G.R. [Terraria srl, Milano (Italy)

2004-07-01

Mestre is the mainland part of the City of Venice, one of the most densely populated urban centres in the Veneto Region. Its ring road is a 6-lane motorway, 8 kilometre long, passing through the urban centre (see. Figure 2). It is a toll-free elevated road, located in the intersection between the most important motorways in North-East Italy: the A4 motorway, connecting NW to NE Italy, and the A27 motorway that is part of the link between Southern and Northern Italy. The ring road is used not only for long-range travels, but also to drive through the urban area of Mestre, avoiding the urban network of roads. During winter time, average daily traffic (ADT) counts up to 40,000 vehicles. 60% is represented by Light Duty Vehicles (LDV), while the remaining 40% by Heavy Duty Vehicles (HDV). The highest ADT counts up to 65,000 vehicles, where 90% is represented by LDV while 10% by HDV. This ADT has been recorded in the summer season, when commuter and commercial travels add to vacation travels, whose destination are the beaches in the Veneto region coastline. (orig.)

eRoads

DEFF Research Database (Denmark)

Connolly, David

vehicles enable more renewable electricity to be integrated onto the electricity grid. This is particularly evident in 2050, since the price of fossil fuels increases while the price of renewable electricity and batteries decreases. Finally, the electric road scenarios can facilitate more reductions......This study compares electric roads with oil (petrol and diesel) and battery electric vehicles, using Denmark as a case study. Electric roads can reduce the cost of electric vehicles by supplying them with electricity directly from the road rather than via a battery for long-distance journeys....... In this paper, an electric road scenario is compared to both an oil and battery electric vehicle scenario using the 2010 Danish energy system, but for two sets of costs: one set based on historical costs from the year 2010 and one based on projected costs for the year 2050. The results indicate that electric...

Estimation of Road Friction Coefficient in Different Road Conditions Based on Vehicle Braking Dynamics

Science.gov (United States)

Zhao, You-Qun; Li, Hai-Qing; Lin, Fen; Wang, Jian; Ji, Xue-Wu

2017-07-01

The accurate estimation of road friction coefficient in the active safety control system has become increasingly prominent. Most previous studies on road friction estimation have only used vehicle longitudinal or lateral dynamics and often ignored the load transfer, which tends to cause inaccurate of the actual road friction coefficient. A novel method considering load transfer of front and rear axles is proposed to estimate road friction coefficient based on braking dynamic model of two-wheeled vehicle. Sliding mode control technique is used to build the ideal braking torque controller, which control target is to control the actual wheel slip ratio of front and rear wheels tracking the ideal wheel slip ratio. In order to eliminate the chattering problem of the sliding mode controller, integral switching surface is used to design the sliding mode surface. A second order linear extended state observer is designed to observe road friction coefficient based on wheel speed and braking torque of front and rear wheels. The proposed road friction coefficient estimation schemes are evaluated by simulation in ADAMS/Car. The results show that the estimated values can well agree with the actual values in different road conditions. The observer can estimate road friction coefficient exactly in real-time and resist external disturbance. The proposed research provides a novel method to estimate road friction coefficient with strong robustness and more accurate.

Use of fatal real-life crashes to analyze a safe road transport system model, including the road user, the vehicle, and the road.

Science.gov (United States)

Stigson, Helena; Krafft, Maria; Tingvall, Claes

2008-10-01

To evaluate if the Swedish Road Administration (SRA) model for a safe road transport system, which includes the interaction between the road user, the vehicle, and the road, could be used to classify fatal car crashes according to some safety indicators. Also, to present a development of the model to better identify system weakness. Real-life crashes with a fatal outcome were classified according to the vehicle's safety rating by Euro NCAP (European Road Assessment Programme) and fitment of ESC (Electronic Stability Control). For each crash, the road was also classified according to EuroRAP (European Road Assessment Programme) criteria, and human behavior in terms of speeding, seat belt use, and driving under the influence of alcohol. Each crash was compared with the model criteria, to identify components that might have contributed to fatal outcome. All fatal crashes where a car occupant was killed that occurred in Sweden during 2004 were included: in all, 215 crashes with 248 fatalities. The data were collected from the in-depth fatal crash data of the Swedish Road Administration (SRA). It was possible to classify 93% of the fatal car crashes according to the SRA model. A number of shortcomings in the criteria were identified since the model did not address rear-end or animal collisions or collisions with stationary/parked vehicles or trailers (18 out of 248 cases). Using the further developed model, it was possible to identify that most of the crashes occurred when two or all three components interacted (in 85 of the total 230 cases). Noncompliance with safety criteria for the road user, the vehicle, and the road led to fatal outcome in 43, 27, and 75 cases, respectively. The SRA model was found to be useful for classifying fatal crashes but needs to be further developed to identify how the components interact and thereby identify weaknesses in the road traffic system. This developed model might be a tool to systematically identify which of the components are

Prioritizing Road Treatments using the Geomorphic Roads Analysis and Inventory Package (GRAIP) to Improve Watershed Conditions in the Wall Creek Watershed, Oregon

Science.gov (United States)

Day, K. T.; Black, T.; Clifton, C.; Luce, C.; McCune, S.; Nelson, N.

2010-12-01

the current rate. These data are being used by the Umatilla National Forest to prioritize road rehabilitation activities including storm risk reduction and road decommissioning, and to move toward an ecologically and economically sustainable road system. The highest sediment-delivering road segments were evaluated in 2010 to prioritize stabilization and storm damage risk reduction projects. Approximately 30 km of hydrologically connected road segments will be proposed for treatments including closure, decommissioning, and stabilization activities. Once complete, these improvements would result in the reduction of about 7,000 kg/year of fine sediment delivered to the fluvial system from the road network, or a third of the total road contribution to stream sedimentation. Methods and results presented are part of federal land management agency involvement in Total Maximum Daily Load development in the John Day Basin. The project is a collaborative effort with funding and support from the Environmental Protection Agency, Bureau of Land Management, and Oregon Department of Environmental Quality.

All-terrain vehicle fatalities on paved roads, unpaved roads, and off-road: Evidence for informed roadway safety warnings and legislation.

Science.gov (United States)

Denning, Gerene M; Jennissen, Charles A

2016-05-18

All-terrain vehicles (ATVs) are designed for off-highway use only, and many of their features create increased risk with roadway travel. Over half of all ATV-related fatalities occur on roadways, and nonfatal roadway crashes result in more serious injuries than those off the road. A number of jurisdictions have passed or have considered legislation allowing ATVs on public roadways, sometimes limiting them to those unpaved, arguing that they are safe for ATVs. However, no studies have determined the epidemiology of ATV-related fatalities on different road surface types. The objective of the study was to compare ATV-related deaths on paved versus unpaved roads and to contrast them with off-road fatalities. Retrospective descriptive and multivariable analyses were performed using U.S. Consumer Product Safety Commission fatality data from 1982 through 2012. After 1998, ATV-related deaths increased at twice the rate on paved versus unpaved roads. Still, 42% of all roadway deaths during the study period occurred on unpaved surfaces. States varied considerably, ranging from 18% to 79% of their ATV-related roadway deaths occurring on unpaved roads. Paved road crashes were more likely than those on unpaved surfaces to involve males, adolescents and younger adults, passengers, and collisions with other vehicles. Both the pattern of other vehicles involved in collisions and which vehicle hit the other were different for the 2 road types. Alcohol use was higher, helmet use was lower, and head injuries were more likely in paved versus unpaved roadway crashes. However, head injuries still occurred in 76% of fatalities on unpaved roads. Helmets were associated with lower proportions of head injuries among riders, regardless of road surface type. Relative to off-road crashes, both paved and unpaved roads were more likely to involve collisions with another vehicle. The vast majority of roadway crashes, however, did not involve a traffic collision on either paved or unpaved roads

Conceptual design and analysis of roads and road construction machinery for initial lunar base operations

Science.gov (United States)

Sines, Jeffrey L.; Banks, Joel; Efatpenah, Keyanoush

1990-01-01

Recent developments have made it possible for scientists and engineers to consider returning to the Moon to build a manned lunar base. The base can be used to conduct scientific research, develop new space technology, and utilize the natural resources of the Moon. Areas of the base will be separated, connected by a system of roads that reduce the power requirements of vehicles traveling on them. Feasible road types for the lunar surface were analyzed and a road construction system was designed for initial lunar base operations. A model was also constructed to show the system configuration and key operating features. The alternate designs for the lunar road construction system were developed in four stages: analyze and select a road type; determine operations and machinery needed to produce the road; develop machinery configurations; and develop alternates for several machine components. A compacted lunar soil road was selected for initial lunar base operations. The only machinery required to produce this road were a grader and a compactor. The road construction system consists of a main drive unit which is used for propulsion, a detachable grader assembly, and a towed compactor.

Deadly dialing : as cell-related accidents climb, Canada's oil industry does its part to make our roads a little safer

Energy Technology Data Exchange (ETDEWEB)

Stastny, P.

2008-04-15

Cellphone use while driving is having a noticeable impact on driver safety. Driving is the leading cause of death in the petroleum industry. Traffic collisions have increased by nearly 15 per cent since 2005. Driver error is considered to be a contributing factor in 9 out of 10 traffic collisions. The media has desensitized and conditioned most people to accept road deaths as inevitable. However, a number of people are now expressing deep concerns over the carelessness of drivers who use their cellphones while on the road. This paper described a campaign recently launched by Alberta's safety training company Enform to develop a policy about cellphone use. The awareness program has been developed to inform the public of the dangers of cellphone use. A team of people have also been hired to conduct safety initiatives in local communities in Alberta. The program is part of the The Alberta Traffic Safety Plan (TSP), which was formed in order to consider methods of increasing public education and awareness, sustained enforcement, legislation, best practices, and safety-based engineering. 3 figs.

Using endemic road features to create self-explaining roads and reduce vehicle speeds.

Science.gov (United States)

Charlton, Samuel G; Mackie, Hamish W; Baas, Peter H; Hay, Karen; Menezes, Miguel; Dixon, Claire

2010-11-01

This paper describes a project undertaken to establish a self-explaining roads (SER) design programme on existing streets in an urban area. The methodology focussed on developing a process to identify functional road categories and designs based on endemic road characteristics taken from functional exemplars in the study area. The study area was divided into two sections, one to receive SER treatments designed to maximise visual differences between road categories, and a matched control area to remain untreated for purposes of comparison. The SER design for local roads included increased landscaping and community islands to limit forward visibility, and removal of road markings to create a visually distinct road environment. In comparison, roads categorised as collectors received increased delineation, addition of cycle lanes, and improved amenity for pedestrians. Speed data collected 3 months after implementation showed a significant reduction in vehicle speeds on local roads and increased homogeneity of speeds on both local and collector roads. The objective speed data, combined with residents' speed choice ratings, indicated that the project was successful in creating two discriminably different road categories. 2010 Elsevier Ltd. All rights reserved.

Road safety performance indicators for the interurban road network.

Science.gov (United States)

Yannis, George; Weijermars, Wendy; Gitelman, Victoria; Vis, Martijn; Chaziris, Antonis; Papadimitriou, Eleonora; Azevedo, Carlos Lima

2013-11-01

Various road safety performance indicators (SPIs) have been proposed for different road safety research areas, mainly as regards driver behaviour (e.g. seat belt use, alcohol, drugs, etc.) and vehicles (e.g. passive safety); however, no SPIs for the road network and design have been developed. The objective of this research is the development of an SPI for the road network, to be used as a benchmark for cross-region comparisons. The developed SPI essentially makes a comparison of the existing road network to the theoretically required one, defined as one which meets some minimum requirements with respect to road safety. This paper presents a theoretical concept for the determination of this SPI as well as a translation of this theory into a practical method. Also, the method is applied in a number of pilot countries namely the Netherlands, Portugal, Greece and Israel. The results show that the SPI could be efficiently calculated in all countries, despite some differences in the data sources. In general, the calculated overall SPI scores were realistic and ranged from 81 to 94%, with the exception of Greece where the SPI was relatively lower (67%). However, the SPI should be considered as a first attempt to determine the safety level of the road network. The proposed method has some limitations and could be further improved. The paper presents directions for further research to further develop the SPI. Copyright © 2012 Elsevier Ltd. All rights reserved.

High Resolution Trichromatic Road Surface Scanning with a Line Scan Camera and Light Emitting Diode Lighting for Road-Kill Detection

Directory of Open Access Journals (Sweden)

Gil Lopes

2016-04-01

Full Text Available This paper presents a road surface scanning system that operates with a trichromatic line scan camera with light emitting diode (LED lighting achieving road surface resolution under a millimeter. It was part of a project named Roadkills—Intelligent systems for surveying mortality of amphibians in Portuguese roads, sponsored by the Portuguese Science and Technology Foundation. A trailer was developed in order to accommodate the complete system with standalone power generation, computer image capture and recording, controlled lighting to operate day or night without disturbance, incremental encoder with 5000 pulses per revolution attached to one of the trailer wheels, under a meter Global Positioning System (GPS localization, easy to utilize with any vehicle with a trailer towing system and focused on a complete low cost solution. The paper describes the system architecture of the developed prototype, its calibration procedure, the performed experimentation and some obtained results, along with a discussion and comparison with existing systems. Sustained operating trailer speeds of up to 30 km/h are achievable without loss of quality at 4096 pixels’ image width (1 m width of road surface with 250 µm/pixel resolution. Higher scanning speeds can be achieved by lowering the image resolution (120 km/h with 1 mm/pixel. Computer vision algorithms are under development to operate on the captured images in order to automatically detect road-kills of amphibians.

High Resolution Trichromatic Road Surface Scanning with a Line Scan Camera and Light Emitting Diode Lighting for Road-Kill Detection.

Science.gov (United States)

Lopes, Gil; Ribeiro, A Fernando; Sillero, Neftalí; Gonçalves-Seco, Luís; Silva, Cristiano; Franch, Marc; Trigueiros, Paulo

2016-04-19

This paper presents a road surface scanning system that operates with a trichromatic line scan camera with light emitting diode (LED) lighting achieving road surface resolution under a millimeter. It was part of a project named Roadkills-Intelligent systems for surveying mortality of amphibians in Portuguese roads, sponsored by the Portuguese Science and Technology Foundation. A trailer was developed in order to accommodate the complete system with standalone power generation, computer image capture and recording, controlled lighting to operate day or night without disturbance, incremental encoder with 5000 pulses per revolution attached to one of the trailer wheels, under a meter Global Positioning System (GPS) localization, easy to utilize with any vehicle with a trailer towing system and focused on a complete low cost solution. The paper describes the system architecture of the developed prototype, its calibration procedure, the performed experimentation and some obtained results, along with a discussion and comparison with existing systems. Sustained operating trailer speeds of up to 30 km/h are achievable without loss of quality at 4096 pixels' image width (1 m width of road surface) with 250 µm/pixel resolution. Higher scanning speeds can be achieved by lowering the image resolution (120 km/h with 1 mm/pixel). Computer vision algorithms are under development to operate on the captured images in order to automatically detect road-kills of amphibians.

Development of roads in the area of the international border crossing Vrtojba

Directory of Open Access Journals (Sweden)

Alojzij Juvanec

2005-01-01

Full Text Available The Republic of Slovenia is part of the European Union. With the abolishment of borders (free flow of goods also the traffic functions in the areas of international border crossings between member countries are changing. Among such border crossings is also the international border crossing (IBC between the Republic of Italy and the Republic of Slovenia in Vrtojba. The bordering communities of Šempeter-Vrtojba and Gorizia (Italy are therefore already preparing a development plan related to the use of space to ensure traffic access to the wider area of this border crossing ,when the “Schengen border” is abolished (free flow of people. Especially important is adequate design of roads that should allow this space to be uniformly and equally included into the road systems of both neighbouring countries. Owing to this change, the existing “communal” road, which today leads to the border crossing, will attain the status of the expressway Ljubljana–Venice via Gorizia, which means that high travelling speeds and changed regime of connecting roads can be expected. The existing arrangement has too many individual connections, and there is the possibility of turning or even parking (in Italy. The paper presents solutions or proposals for a systematic rearrangement of the present road through the IBC to the motorway and the principle of connecting the road networks of both neighbouring communities to it. Presented are also proposals how to rearrange or complete the existing local road networks and the railway infrastructure (arrangement of an intermodal terminal, and the traffic regime on roads to achieve as efficient use of space as possible at the present IBC Vrtojba with the least possible burden to the space.

Road accident rates: strategies and programmes for improving road traffic safety.

Science.gov (United States)

Goniewicz, K; Goniewicz, M; Pawłowski, W; Fiedor, P

2016-08-01

Nowadays, the problem of road accident rates is one of the most important health and social policy issues concerning the countries in all continents. Each year, nearly 1.3 million people worldwide lose their life on roads, and 20-50 million sustain severe injuries, the majority of which require long-term treatment. The objective of the study was to identify the most frequent, constantly occurring causes of road accidents, as well as outline actions constituting a basis for the strategies and programmes aiming at improving traffic safety on local and global levels. Comparative analysis of literature concerning road safety was performed, confirming that although road accidents had a varied and frequently complex background, their causes have changed only to a small degree over the years. The causes include: lack of control and enforcement concerning implementation of traffic regulation (primarily driving at excessive speed, driving under the influence of alcohol, and not respecting the rights of other road users (mainly pedestrians and cyclists), lack of appropriate infrastructure and unroadworthy vehicles. The number of fatal accidents and severe injuries, resulting from road accidents, may be reduced through applying an integrated approach to safety on roads. The strategies and programmes for improving road traffic should include the following measures: reducing the risk of exposure to an accident, prevention of accidents, reduction in bodily injuries sustained in accidents, and reduction of the effects of injuries by improvement of post-accident medical care.

Assessment of Road Infrastructures Pertaining to Malaysian Experience

Directory of Open Access Journals (Sweden)

Samsuddin Norshakina

2016-01-01

Full Text Available Road Infrastructures contribute towards many severe accidents and it needs supervision as to improve road safety levels. The numbers of fatalities have increased annually and road authority should seriously consider conducting programs or activities to periodically monitor, restore of improve road infrastructure. Implementation of road safety audits may reduce fatalities among road users and maintain road safety at acceptable standards. This paper is aimed to discuss the aspects of road infrastructure in Malaysia. The research signifies the impact of road hazards during the observations and the impact of road infrastructure types on road accidents. The F050 (Jalan Kluang-Batu Pahat road case study showed that infrastructure risk is closely related with number of accident. As the infrastructure risk increase, the number of road accidents also increase. It was also found that different road zones along Jalan Kluang-Batu Pahat showed different level of intersection volume due to number of road intersection. Thus, it is hoped that by implementing continuous assessment on road infrastructures, it might be able to reduce road accidents and fatalities among drives and the community.

Where Does Road Salt Go - a Static Salt Model

Science.gov (United States)

Yu, C. W.; Liu, F.; Moriarty, V. W.

2017-12-01

Each winter, more than 15 million tons of road salt is applied in the United States for the de-icing purpose. Considerable amount of chloride in road salt flows into streams/drainage systems with the snow melt runoff and spring storms, and eventually goes into ecologically sensitive low-lying areas in the watershed, such as ponds and lakes. In many watersheds in the northern part of US, the chloride level in the water body has increased significantly in the past decades, and continues an upward trend. The environmental and ecological impact of the elevated chloride level can no longer be ignored. However although there are many studies on the biological impact of elevated chloride levels, there are few investigations on how the spatially distributed road salt application affects various parts of the watershed. In this presentation, we propose a static road salt model as a first-order metric to address spacial distribution of salt loading. Derived from the Topological Wetness Index (TWI) in many hydrological models, this static salt model provides a spatial impact as- sessment of road salt applications. To demonstrate the effectiveness of the static model, National Elevation Dataset (NED) of ten-meter resolution of Lake George watershed in New York State is used to generate the TWI, which is used to compute a spatially dis- tributed "salt-loading coefficient" of the whole watershed. Spatially varying salt applica- tion rate is then aggregated, using the salt-loading coefficients as weights, to provide salt loading assessments of streams in the watershed. Time-aggregated data from five CTD (conductivity-temperature-depth) sensors in selected streams are used for calibration. The model outputs and the sensor data demonstrate a strong linear correlation, with the R value of 0.97. The investigation shows that the static modeling approach may provide an effective method for the understanding the input and transport of road salt to within watersheds.

Road density

Data.gov (United States)

U.S. Environmental Protection Agency — Road density is generally highly correlated with amount of developed land cover. High road densities usually indicate high levels of ecological disturbance. More...

Impacts of road deicing salt on the demography of vernal pool-breeding amphibians.

Science.gov (United States)

Karraker, Nancy E; Gibbs, James P; Vonesh, James R

2008-04-01

Deicing agents, primarily road salt, are applied to roads in 26 states in the United States and in a number of European countries, yet the scale of impacts of road salt on aquatic organisms remains largely under-studied. The issue is germane to amphibian conservation because both adult and larval amphibians are known to be particularly sensitive to changes in their osmolar environments. In this study, we combined survey, experimental, and demographic modeling approaches to evaluate the possible effects of road salt on two common vernal-pond-breeding amphibian species, the spotted salamander (Ambystoma maculatum) and the wood frog (Rana sylvatica). We found that in the Adirondack Mountain Region of New York (USA), road salt traveled up to 172 m from the highway into wetlands. Surveys showed that egg mass densities of spotted salamanders (A. maculatum) and wood frogs (R. sylvatica) were two times higher in forest pools than roadside pools, but this pattern was better explained by road proximity than by increased salinity. Experiments demonstrated that embryonic and larval survival were reduced at moderate (500 muS) and high conductivities (3000 muS) in A. maculatum and at high conductivities in R. sylvatica. Demographic models suggest that such egg and larval stage effects of salt may have important impacts on populations near roads, particularly in the case of A. maculatum, for which salt exposure may lead to local extinction. For both species, the effect of road salt was dependent upon the strength of larval density dependence and declined rapidly with distance from the roadside, with the greatest negative effects being limited to within 50 m. Based on this evidence, we argue that efforts to protect local populations of A. maculatum and R. sylvatica in roadside wetlands should, in part, be aimed at reducing application of road salt near wetlands with high conductivity levels.

Modernization of the Russian Automobile Road Network on the Base of Innovative Technologies

Directory of Open Access Journals (Sweden)

E. A. Zhukov

2017-01-01

Full Text Available Purpose: the main goal of the article is to build a conceptual model for the organization of effective functioning of the points of economic and innovative growth of the region in modern conditions, taking into account regional and municipal limitations of internal and external nature, with the aim of ensuring economic security, effective interaction of subjects of the "business-power" system Taking into account the influence of institutional factors. Methods: in the present study the following methods were used: systemic approach, methods of social diagnosis, comparative analysis, method of expert evaluations, and method of statistical processing of information. Results: the short characteristic of modern development and technical level of the Russian automobile roads network as the important part of the automobile roads material-technical base is presented. Realization process of the actual task putted by Russian President V.V. Putin to transport builders: two times increasing construction of automobile roads is analyzed. The reality of decision this task due to modernization roads economy material-technical base on the base of innovative technologies and progressive world experience in the field of roads construction is scientifically proved. Conclusions and Relevance: in spite of losing now in decision of the actual task putted by Russian President V.V. Putin to transport builders: two times increasing construction of automobile roads, nevertheless the real possibilities to reach the important aim still remain. It may be done only due to scientifically grounded modernization of the roads economy material-technical base on the base of innovative technologies and progressive world experience in the field of roads construction 

Road Infrastructure and Road User’s Satisfactions: A Case Study of Motorway Route 7, Thailand

Directory of Open Access Journals (Sweden)

Suanmali Suthathip

2014-01-01

Full Text Available The development of tourism in Thailand relies on the development of appropriate infrastructure. Road access is the key infrastructure issue for tourist destinations throughout Thailand. Each year Thailand has welcomed over 15 million travelers, accounted approximately 7% of GDP. To support tourist activities, variety types of transportation modes have designed. However, road transportation is one of the most effective modes that connect most places together. Beside high-standard vehicles, road is another mechanism that derive comfort and safety of travelling. For this reason, Motorway networks were initiated and constructed to support high speed traffic with high safety and standard. Motorway route 7 is one of major motorway networks that lies between major cities and tourist landmarks. To raise the road standard could be the key to support tourist industry and economic growth. The road developments may not be precise and accurate without knowing the needs from road users’. Therefore, a questionnaire is developed and distributed to 890 randomly selected road users along Motorway route 7. Factor analysis and t-test are employed to analyze the factors affecting road users’ satisfaction and to compare the satisfaction level between both inbound and outbound travelers.

Road Closures

Data.gov (United States)

Montgomery County of Maryland — This is an up to date map of current road closures in Montgomery County.This dataset is updated every few minutes from the Department of Transportation road closure...

On the Horn Effect of a Tyre/road Interface, Part i: Experiment and Computation

Science.gov (United States)

Graf, R. A. G.; Kuo, C.-Y.; Dowling, A. P.; Graham, W. R.

2002-09-01

Near the tyre/road contact area, the road surface and the tyre belt form a horn-like geometry, which provides a significant amplification mechanism for sound sources. Measurements have been carried out on a stationary tyre placed on a plane surface in an otherwise anechoic chamber. Following the reciprocal theorem a microphone was placed in the road surface near the contact patch and a white noise source was used in the far field. The amplification by the horn effect can then be determined as a function of frequency for an array of microphone positions relative to the contact patch and the centre of the tyre. These experimental measurements show that the horn effect is responsible for about 10-20dB increase in noise level. The amplification function shows a distinct interference pattern for higher frequencies and is independent of the longitudinal source position for low frequencies and source positions close to the contact patch. Numerical calculations using the indirect boundary element method have been carried out. These show excellent agreement with the measurements in the frequency regime of the BEM, i.e., up to 2500 Hz. The dependence of the horn effect on primary geometrical parameters such as the effect of the radius of curvature of the shoulders, the load and the width of the tyre has been investigated experimentally and numerically. The broad features of the horn effect are given by the cylindrical geometry of the tyre. The rounded edges of the tyre tend to increase the levels of the minima and shift them to higher frequencies, while slightly decreasing the levels of the maxima. Shape variations due to load can be accounted for by correcting the source distance to the edge of the formed contact patch. The amplification at low frequencies increases with width, the results collapsing onto a single curve as a function of the dimensionless width ω / λ.

Sustainable road safety: a new (?) neighbourhood road pattern that saves VRU lives.

Science.gov (United States)

Wei, Vicky Feng; Lovegrove, Gord

2012-01-01

Both the UN (2007) and World Health Organizations (2004) have declared the enormous social and economic burden imposed on society by injuries due to road collisions as a major global problem. While the road safety problem is not new, this prominent global declaration sends an important signal of frustration regarding progress to date on reducing road collisions. It is clear that governments, communities, businesses and the public must discover ways of reducing this burden, especially as it relates to vulnerable road users (VRUs), typically meaning pedestrian and bicyclist road users. Recent comparisons of global VRU collisions statistics suggest that, in addition to mixed land use density, the layout of neighbourhood roads plays a vital role in the encouragement of walkable, safe and quiet, yet accessible and sustainable communities. The purpose of this paper was to: The Dutch Sustainable Road Safety (SRS) Program has produced a number of innovative land use and transportation initiatives for vehicular road users as well as non-vehicular VRUs. Following from the Dutch initiatives, these new 3-way offset, and fused grid neighbourhood patterns appear to not only have positive effects in encouraging mode split (i.e. increasing walking and bicycling, and transit), slowing traffic, and reducing energy consumption and GHG emissions; but also, to hold potential to improve road safety. To test the road safety hypothesis, UBCO researchers evaluated the level of road safety relative to five neighbourhood patterns - grid, culs-de-sac, and Dutch Sustainable Road Safety (SRS) (or limited access), 3-way offset, and fused grid networks. Analysis using standard transportation planning methodology revealed that they would maintain both mobility and accessibility. Analysis using standard road safety analysis methodology further revealed that these 3-way offset, and fused grid patterns would significantly improve road safety levels by as much as 60% compared to prevalent patterns (i

Public road infrastructure inventory in degraded global navigation satellite system signal environments

Science.gov (United States)

Sokolova, N.; Morrison, A.; Haakonsen, T. A.

2015-04-01

Recent advancement of land-based mobile mapping enables rapid and cost-effective collection of highquality road related spatial information. Mobile Mapping Systems (MMS) can provide spatial information with subdecimeter accuracy in nominal operation environments. However, performance in challenging environments such as tunnels is not well characterized. The Norwegian Public Roads Administration (NPRA) manages the country's public road network and its infrastructure, a large segment of which is represented by road tunnels (there are about 1 000 road tunnels in Norway with a combined length of 800 km). In order to adopt mobile mapping technology for streamlining road network and infrastructure management and maintenance tasks, it is important to ensure that the technology is mature enough to meet existing requirements for object positioning accuracy in all types of environments, and provide homogeneous accuracy over the mapping perimeter. This paper presents results of a testing campaign performed within a project funded by the NPRA as a part of SMarter road traffic with Intelligent Transport Systems (ITS) (SMITS) program. The testing campaign objective was performance evaluation of high end commercial MMSs for inventory of public areas, focusing on Global Navigation Satellite System (GNSS) signal degraded environments.

A Study on the Influence of Speed on Road Roughness Sensing: The SmartRoadSense Case

Directory of Open Access Journals (Sweden)

Giacomo Alessandroni

2017-02-01

Full Text Available SmartRoadSense is a crowdsensing project aimed at monitoring the conditions of the road surface. Using the sensors of a smartphone, SmartRoadSense monitors the vertical accelerations inside a vehicle traveling the road and extracts a roughness index conveying information about the road conditions. The roughness index and the smartphone GPS data are periodically sent to a central server where they are processed, associated with the specific road, and aggregated with data measured by other smartphones. This paper studies how the smartphone vertical accelerations and the roughness index are related to the vehicle speed. It is shown that the dependence can be locally approximated with a gamma (power law. Extensive experimental results using data extracted from SmartRoadSense database confirm the gamma law relationship between the roughness index and the vehicle speed. The gamma law is then used for improving the SmartRoadSense data aggregation accounting for the effect of vehicle speed.

The Influence of Visibility Conditions in Horizontal Road Curves on the Efficiency of Noise Protection Barriers

Directory of Open Access Journals (Sweden)

Džambas Tamara

2013-12-01

Full Text Available Ensuring sufficient visibility on planned roads by sight distance testing is an integral part of every project, but problems with visibility can emerge when noise barriers are erected on existing roads. Namely, in order to provide sufficient noise protection, high noise barriers are often placed at minimum distance from the carriageway edge, and additional visibility testing in most cases is not carried out.

Emissions of road dust by winter tyres and the contributions of different road dust sources in road side particle samples; Talvirenkaiden poelypaeaestoet ja eri katupoelylaehteiden osuudet kadunvarrella keraetyissae hiukkasnaeytteissae

Energy Technology Data Exchange (ETDEWEB)

Kupiainen, K.; Pirjola, L.; Ritola, R.; Stojiljkovic, A.; Malinen, A.

2013-09-01

Aim of this study was to determine: (1) the relative contributions from pavement wear and traction sanding in PM{sub 10} road side air and road dust resuspension samples; (2) PM{sub 10} dust emissions from studded and studless tyres in on-road conditions. The study was conducted as part of the NASTA research program during the winter season 2011/2012. The studies were carried out in Suurmetsaentie and Viikintie in Helsinki, Finland. The results showed that dust from pavement aggregates was the largest source during spring, accounting for 40- 50 percent of the particulate matter in the air and resuspension samples. Based on studies on formation of dust, major source of the dust from pavement aggregates is the wear by studded tyres. Traction sand and road salt were used frequently during the winter 2011/2012. Sanding material explained about 25 percent of the road dust in the air and resuspension samples. Traction sanding is estimated to account for approximately few percent of the pavement dust via the sandpaper effect. Effect of road salt was few percent in the samples. The source contributions from pavement and traction sanding observed in spring 2011/2012 at Suurmetsaentie are similar to what has been estimated in previous studies conducted in the early 2000s in Finland. In a study conducted in the city of Hanko, it was estimated the contribution from traction sanding to be in average of about 10 percent. In another study in the center of Helsinki the contribution was estimated to be about half of the PM{sub 10}. The general perception in Finland has been that traction sanding is the main source of airborne road dust. Studies conducted in 2000s and the results of this study, however, indicate that traction sanding has been an important but not the main source of PM10 road dust even in winters with extensive use of gravel for traction control. Emissions of road dust by a single tyre consist of direct emissions of wear products as well as resuspension emissions of

Vehicle Speed Determination in Case of Road Accident by Software Method and Comparing of Results with the Mathematical Model

OpenAIRE

Hoxha Gezim; Shala Ahmet; Likaj Rame

2017-01-01

The paper addresses the problem to vehicle speed calculation at road accidents. To determine the speed are used the PC Crash software and Virtual Crash. With both methods are analysed concrete cases of road accidents. Calculation methods and comparing results are present for analyse. These methods consider several factors such are: the front part of the vehicle, the technical feature of the vehicle, car angle, remote relocation after the crash, road conditions etc. Expected results with PC Cr...

Burden of road traffic injuries related to delays in implementing safety belt laws in low- and lower-middle-income countries.

Science.gov (United States)

Martin, Aurélie; Lagarde, Emmanuel; Salmi, L Rachid

2018-02-28

Delayed implementation of effective road safety policies must be considered when quantifying the avoidable part of the fatal and nonfatal injuries burden. We sought to assess the avoidable part of disability-adjusted life years (DALYs) lost due to road traffic injuries related to delays in implementing road safety laws in low- and lower-middle-income countries. We chose one country for each of the regions of the World Health Organization (WHO) and World Bank (WB) country income levels. We used freely available data sets (WHO, International Traffic Safety Data and Analysis Group, the WB). Delays in implementation were calculated until 2013, from the year mandatory use of safety belts by motor vehicle front seat occupants was first introduced worldwide. We used life expectancy tables and age groups as social values in the DALY calculation model. From the estimated total burden, avoidable DALYs were calculated using estimates of the effectiveness of seat belt laws on fatal and nonfatal injuries combined, as extracted from published international reviews of evidence. From the reference year 1972, implementation delays varied from 27 years (Uzbekistan) to 41 years in Bolivia (no seat belt law as of 2013). During delays, total absolute numbers of DALYs lost due to road traffic injuries reached 8,462,099 in Nigeria, 7,203,570 in Morocco, 4,695,500 in Uzbekistan, 3,866,391 in Cambodia, 3,253,359 in Bolivia, and 3,128,721 in Sri Lanka. Using effectiveness estimates ranging from 3 to 20% reduction, the avoidable burden of road traffic injuries for car occupants was highest in Uzbekistan (avoidable part from 1.2 to 10.4%) and in Morocco (avoidable part from 1.5 to 12.3%). In countries where users of public transport and pedestrians were the most affected by the burden, the avoidable parts ranged from 0.5 to 4.4% (Nigeria) and from 0.5 to 3.4% (Bolivia). Burden of road traffic injuries mostly affected motorcyclists in Sri Lanka and Cambodia where the avoidable parts were

Road rage and road traffic accidents among commercial vehicle drivers in Lahore, Pakistan.

Science.gov (United States)

Shaikh, M A; Shaikh, I A; Siddiqui, Z

2012-04-01

Road rage and road traffic accidents increase the burden of morbidity and mortality in a population. A cross-sectional survey with convenience sampling was conducted among commercial vehicle drivers in Lahore, Pakistan (n = 901) to record their behaviours/experiences regarding road rage and road traffic accidents. Respondents were asked about incidents of shouting/cursing/rude gestures or threats to physically hurt the person/vehicle, by others or themselves, in the previous 24 hours or 3 months, and their involvement in road traffic accidents in the previous 12 months. Auto-rickshaw drivers were significantly more likely to report various road rage experiences/behaviours and involvement in accidents compared with bus and wagon drivers. A total of 112 respondents (12.4%) reported being involved in a road traffic accident in the previous 12 months but traffic police did not record the accident in 52.7% of cases. The results of this study underline the need to improve road safety in Pakistan.

Reflection properties of road surfaces. Contribution to OECD Scientific Expert Group AC4 on Road Surface Characteristics.

NARCIS (Netherlands)

Schreuder, D.A.

1983-01-01

Photometric characteristics of road surfaces are dealt with. Representation of reflection properties in public lighting; quality criteria of road lighting installations; classification of road surfaces; the relation between reflection characteristics and other properties of road pavements in public

The importance of accurate road data for spatial applications in public health: customizing a road network

Directory of Open Access Journals (Sweden)

Laraia Barbara A

2009-05-01

Full Text Available Abstract Background Health researchers have increasingly adopted the use of geographic information systems (GIS for analyzing environments in which people live and how those environments affect health. One aspect of this research that is often overlooked is the quality and detail of the road data and whether or not it is appropriate for the scale of analysis. Many readily available road datasets, both public domain and commercial, contain positional errors or generalizations that may not be compatible with highly accurate geospatial locations. This study examined the accuracy, completeness, and currency of four readily available public and commercial sources for road data (North Carolina Department of Transportation, StreetMap Pro, TIGER/Line 2000, TIGER/Line 2007 relative to a custom road dataset which we developed and used for comparison. Methods and Results A custom road network dataset was developed to examine associations between health behaviors and the environment among pregnant and postpartum women living in central North Carolina in the United States. Three analytical measures were developed to assess the comparative accuracy and utility of four publicly and commercially available road datasets and the custom dataset in relation to participants' residential locations over three time periods. The exclusion of road segments and positional errors in the four comparison road datasets resulted in between 5.9% and 64.4% of respondents lying farther than 15.24 meters from their nearest road, the distance of the threshold set by the project to facilitate spatial analysis. Agreement, using a Pearson's correlation coefficient, between the customized road dataset and the four comparison road datasets ranged from 0.01 to 0.82. Conclusion This study demonstrates the importance of examining available road datasets and assessing their completeness, accuracy, and currency for their particular study area. This paper serves as an example for assessing

Gravel roads management : volume 1, gravel roads management.

Science.gov (United States)

2010-10-01

This report establishes procedures for managing dirt and gravel roads, with a primary focus on smaller agencies, such as Wyoming counties, that must manage their roads with very limited resources. The report strives, first, to guide and assist smalle...

Wenders in Motion: A Study On The Way Of Characterization In Wim Wenders’ Road Movies

Directory of Open Access Journals (Sweden)

Erman Pehlivan

2013-06-01

Full Text Available Famous for his road movies, WimWenders, has a deeper understanding of the word; motion. More than often,Wenders tells the story of wanderers by putting them in a constant state oftravel.  These travels alter thewanderers’ characters and play a key role in Wenders’ storytelling. This paperstudies Wim Wenders’ way of characterization in three parts. The first partstates out keywords to define Wim Wenders’ wanderers: movement/motion, thejourney, homesickness, spatial levels, the Ozu connection. And it mainlyfocuses on his road trilogy: Im Lauf der Zeit (1976, FalscheBewegung (1975, and Alice in den Städten (1974, whileexplaining the stated keywords. The second part only focuses on Paris, Texas(1984 and its main character Travis, who might be seen as the ultimatewanderer whom all other Wenders’ characters blend in to. Thethird and the final part takes Der Himmel Über Berlin (1987 as ‘avertical road movie’ hoping for finding a cure for the worldwide homesicknessthat all the Wenders’ wanderers suffer.  Also there are a handful of musicreferences hidden through the paper in homage to director’s love for rock ‘n’roll music.

An Evaluation of Forest Road Standards and Road Gradients in Turkey in View of FAO Criteria and Some EU Practices

Directory of Open Access Journals (Sweden)

Sadık Çağlar

2009-04-01

Full Text Available Forest roads are one of the inevitable infrastructures in conducting forestry operations. Around 1000 km under standardized forest roads have been largely repaired in addition to construction of 1000 km new forest roads in Turkey. Implementing uniform road gradient along the road sections is very important in terms of transportation techniques and safety, as well as the geometrical standardizations of the forest road. In this study, current road standards, longitudinal gradient values and their limitations in forest road constructions recommended by Food and Agriculture Organization of the United Nations (FAO and some Europe Union (EU countries were examined. Firstly, the forest road standards and their gradient values have been defined in Turkish forest road construction practices. Afterwards, the forest road standards and the gradient values applied by FAO and some EU countries were presented, and finally, the specifications were examined by comparing them with the current practices in Turkish forestry.

Opportunities of forest roads usage as emergency access road for natural disaster

Directory of Open Access Journals (Sweden)

Can Vatandaşlar

2016-07-01

Full Text Available This study was carried out to examine the applicability of forest roads as emergency access and evacuation corridor for an alternative to motorways following a prospective earthquake in İstanbul. For this purpose, various disaster scenarios were created in the district of Beykoz and the shortest routes between critical points were determined through network analysis in Geographic Information System (GIS. Results indicated that access was possible between Beykoz city center and shelter, hospital, fire station, disaster management center, and military area via forest roads even if motorways became unusable. However, distance generally got longer and time of arrival increased on the routes of forest road. The increase in time of arrival was attributed to decrease in average cruising speed in addition to the increase in distance. This limitation can be overcome by enhancing the geometric standards of forest roads and completing superstructure operations. Results are important for revealing that forest roads can be used in other fields besides forestry activities, they can strengthen decision support system of managers, and enable first aid crew to reach the scene in the minimal time.

Overview of the neural network based technique for monitoring of road condition via reconstructed road profiles

CSIR Research Space (South Africa)

Ngwangwa, HM

2008-07-01

Full Text Available on the road and driver to assess the integrity of road and vehicle infrastructure. In this paper, vehicle vibration data are applied to an artificial neural network to reconstruct the corresponding road surface profiles. The results show that the technique...

Tourist Assessment of Croatian Roads

Directory of Open Access Journals (Sweden)

Joso Vurdelja

2012-10-01

Full Text Available As environmentally clean industry and as the most significantworld industry regarding the number of employees and theimpact on the social and economic development of a countTy,tourism represents an extremely important social and economicbranch for Croatia.As a functional unit of the mutually interweaving socialand economic relations, tourism is a complex phenomenonwhose development depends on a number of compatible factorsout of which the transport infrastructure is considered to bethe most obvious and almost the most significant one, i.e. thefirst among the equal. This is primarily true for road traffic infrastructure,since road trai!Sportation of tourists by passengercars, buses and motorcycles accounts for more than 90 percentof the overall tourist journeys in Croatia.The topic of this paper is precisely, among other things, thetourist assessment of the Croatian road network by means ofthe so-called econometric model regarding the contribution ofa certain road route to the overall tourist traffic.Practical implementation of the elaborated problematicshould result in the improvement of road infrastructure eitherby constructing new motonvays and/or roads, or by reconstructionand/or modernisation of the existing traffic routes.

A road safety course with a difference!

CERN Document Server

2008-01-01

Are you feeling brave? Then why not sign up for a road safety session. 10 to 14 November is road safety week at CERN and the Touring Club Suisse (TCS) will be in the Main Building, 500, with several hair-raising activities to try. If you walk into the foyer of building 500 between 10 and 14 November you might, at first glance, think that you have walked into a fairground. But the machines designed to spin you upside down and slide you also are actually part of CERN’s road safety week. Every day during the week there will six sessions each lasting about an hour where you can try out a series of exhilarating activities. If you are feeling brave enough you could try and get yourself out of the crash simulator. Not as easy as it sounds - after being spun over several times you can experience what it’s like to try and escape from an overturned car - dangling upside down attached only by your seatbelt! During the course instructors from the Touring Club Suisse (TC...

The Development of child road safety competence : the new approach tо road safety education

OpenAIRE

Vilkonis, Rytis

2005-01-01

The education and information are the strategies of the Road safety. However, some of the documents and scientific findings revealed the chaotic, desultory and theoretically groundless Road safety education and it can be stated that Road safety education system in Lithuania is still being established. The shortage of the theoretical and empirical base of Road safety education is slowing down the process of the system development. Aim of the research is to disclose the assumptions for developm...

Method for estimating road salt contamination of Norwegian lakes

Science.gov (United States)

Kitterød, Nils-Otto; Wike Kronvall, Kjersti; Turtumøygaard, Stein; Haaland, Ståle

2013-04-01

Consumption of road salt in Norway, used to improve winter road conditions, has been tripled during the last two decades, and there is a need to quantify limits for optimal use of road salt to avoid further environmental harm. The purpose of this study was to implement methodology to estimate chloride concentration in any given water body in Norway. This goal is feasible to achieve if the complexity of solute transport in the landscape is simplified. The idea was to keep computations as simple as possible to be able to increase spatial resolution of input functions. The first simplification we made was to treat all roads exposed to regular salt application as steady state sources of sodium chloride. This is valid if new road salt is applied before previous contamination is removed through precipitation. The main reasons for this assumption are the significant retention capacity of vegetation; organic matter; and soil. The second simplification we made was that the groundwater table is close to the surface. This assumption is valid for major part of Norway, which means that topography is sufficient to delineate catchment area at any location in the landscape. Given these two assumptions, we applied spatial functions of mass load (mass NaCl pr. time unit) and conditional estimates of normal water balance (volume of water pr. time unit) to calculate steady state chloride concentration along the lake perimeter. Spatial resolution of mass load and estimated concentration along the lake perimeter was 25 m x 25 m while water balance had 1 km x 1 km resolution. The method was validated for a limited number of Norwegian lakes and estimation results have been compared to observations. Initial results indicate significant overlap between measurements and estimations, but only for lakes where the road salt is the major contribution for chloride contamination. For lakes in catchments with high subsurface transmissivity, the groundwater table is not necessarily following the

Demand for road-fuel in a small developing economy: The case of Sri Lanka

International Nuclear Information System (INIS)

Chandrasiri, Sunil

2006-01-01

This paper estimates the demand for road fuel (petrol and auto-diesel) in the context of a small developing economy-Sri Lanka. The data set covers a period of 39 years from 1964 to 2002 representing both close economy and open economy policy regimes. The estimation procedure is based on seemingly unrelated regression equation (SURE) methodology mainly to capture substitutability of petrol and diesel in road transportation. The effect of auto-fuel prices on vehicle demand is also analyzed as a part of the analysis. In addition to confirming existing evidence on road-fuel demand, the findings reveal some interesting evidence with respect to own-price elasticity, cross-price elasticity, lag effects, income and vehicle mix variables

Access road reclamation

International Nuclear Information System (INIS)

Manson, T.; Blok, M.

1997-01-01

A general review of the measures involved in restoring abandoned access road sites in British Columbia was presented. Permits and licences are needed for the use of crown land for roads used by the petroleum and natural gas industry for exploration activities. However, the regulatory framework for road site reclamation is not well developed. The nature of access road reclamation is very site-specific. Some of the issues that are considered for all reclamation projects include slope stability, water control, revegetation, soil rehabilitation, access management and monitoring. The primary objective of reclaiming access road sites is to return the site to conditions that are equal or better than pre-disturbance conditions. Restoration measures must be approved by BC Environment and by the Department of Fisheries and Oceans where federal fisheries responsibilities are involved. 54 refs., 5 tabs., 3 figs

The feedback control research on straight and curved road with car-following model

Science.gov (United States)

Zheng, Yi-Ming; Cheng, Rong-Jun; Ge, Hong-Xia

2017-07-01

Taking account of the road consisting of curved part and straight part, an extended car-following model is proposed in this paper. A control signal including the velocity difference between the considered vehicle and the vehicle in front is taken into account. The control theory method is applied into analysis of the stability condition for the model. Numerical simulations are implemented to prove that the stability of the traffic flow strengthens effectively with an increase of the radius of curved road, and the control signal can suppress the traffic congestion. The results are in good agree with the theoretical analysis.

Application of surplus and waste materials in roads pavement making

OpenAIRE

Mousavi, S. M.; Fazli, A. H.; Rouzmehr, F.

2011-01-01

Nowadays there are a lot of problems about surpluses and debris made by humans all around the world. Lots of these surpluses seriously harm our natural environment. Reuse of this kind of materials in other processes like building constructions or pavement help our natural environment in every aspect. Asphalt concrete is the main part of pavements in most parts of the world with an increasing rate of production in need of more ways and roads. In this paper we will provide...

Armenia - Rural Road Rehabilitation

Data.gov (United States)

Millennium Challenge Corporation — The key research questions guiding our design of the RRRP evaluation are: • Did rehabilitating roads affect the quality of roads? • Did rehabilitating roads improve...

Emission factors from road traffic from a tunnel study (Gubrist tunnel, Switzerland). Part 1 Concept and first results

Energy Technology Data Exchange (ETDEWEB)

Staehelin, Johannes; Brunner, Dominik; Baumle, Martin [Atmospheric Science, ETH-Hoenggerberg, Zuerich (Switzerland); Schlapfer, Kurt [Carbotech AG, Basel (Switzerland); Burgin, Toni; Meier, Markus [Amt fuer Technische Anlagen und Lufthygiene Kanton Zuerich ATAL, Zuerich (Switzerland); Steinemann, Urs [Ingenieurbuero Steinemann, Wollerau (Switzerland); Schneider, Stefan; Zahner, Christoph; Keiser, Stephan [Planungsbuero Jud AG, Zuerich (Switzerland); Stahel, Werner; Keller, Christian [Sem. for Statistics, ETH-Z, Zuerich (Switzerland)

1995-06-22

In the industrialized world a large part of the emission of the primary air pollutants (NO{sub x}, volatile organic compounds (VOC) and CO) originates from road traffic. Here we present the concept and first results of a tunnel study which took place from September 20th to September 26th, 1993, at the Gubrist tunnel (close to Zuerich, Switzerland) in which the emission factors of a large number of individual VOCs, total hydrocarbons (t-HC), CO, NO{sub x} and SO{sub 2} are determined. The first tentative results of the emission factors of NO{sub x}, CO, t-HC and 26 individual hydrocarbons (alkanes and aromatics in the volatility range from n-heptane to n-decane) for the average of all vehicles and the light duty vehicles at an average speed of 90 km/h are given

Solutions to Improve Road Circulation in the Pitesti City Based on Analysis-Diagnostics of Road Traffic

Science.gov (United States)

Vîlcan, A.; Neagu, E.; Badarau Suster, H.; Boroiu, A. A.

2017-10-01

Road traffic congestion has become a daily phenomenon in the central area of Pitesti in the peak traffic periods. In order to achieve the mobility plan of Pitesti, an important stage is the diagnostic analysis of the road traffic. For this purpose, the urban road network was formalized through a graph containing the most important 40 intersections and traffic measurements were made at all these intersections and on the main roads connecting the peri-urban area. The data obtained by traffic macrosimulation confirmed the overloading of the street network during peak traffic hours and the analyzes made for various road traffic organization scenarios have shown that there are sustainable solutions for urban mobility only if the road network is fundamentally reconfigured (a belt outside the city and a median ring). Thus, the necessity of realizing the road passage in the Prundu neighbourhood and the finishing of the city belt by realizing the “detour West” of the city is argued. The importance of the work is that it brings scientific arguments for the realization of these road infrastructure projects, integrated in the urban mobility plan, which will base the development strategy of the Pitesti municipality.

Comparison of Community Response to Road Traffic Noise in Japan and SWEDEN—PART i: Outline of Surveys and DOSE-RESPONSE Relationships

Science.gov (United States)

SATO, T.; YANO, T.; BJÖRKMAN, M.; RYLANDER, R.

2002-02-01

To investigate cross-cultural differences in the community response to road traffic noise, social surveys were conducted in Gothenburg, Sweden, and Kumamoto and Sapporo, Japan, using the same questionnaire and noise measurement method. Typical residential areas with detached houses and apartments were selected as the target areas in each city. The questionnaire comprised 40 questions relating to environmental, housing and personal factors. The key questions concerned annoyance caused by road traffic noise. The total numbers of respondents were 1142 in Gothenburg, 837 in Kumamoto and 780 in Sapporo. The response rates were 68·8, 69·3 and 57·5% respectively. After the questionnaires were completed, noise measurements were made in each area. Community responses were compared on the basis of the dose-response relationships. There were no systematic differences between community responses in Sapporo and Kumamoto, which have the same culture. People living in detached houses in Gothenburg were more annoyed by the same road traffic noise than the people living in Japanese cities. There were no systematic differences among the three cities with regard to activity disturbances indoors, but significant disturbance of activities and resting in gardens or on balconies was noted in Gothenburg. The difference in activity disturbance was due to the differences between lifestyles in the two countries. People living in detached houses were more annoyed by the house vibration caused by road traffic than those living in apartments and people were annoyed by the exhaust from road traffic to the same extent as noise.

Environmental sensitive road planning and transportation techniques in forest engineering

Directory of Open Access Journals (Sweden)

H. Hulusi Acar

2016-07-01

Full Text Available Forestry management has activities dealing with technical, economic, social and environmental services. Forestry operations which are carried out on forest areas , an important part of the ecosistem are materialized in open space. This forestry activities on large areas and high sloping generally, include many different techniques. It is needed primarily to the forest road network in terms of forest management. Determining the approriate route in the natural environment, planning and road construction affairs for forest roads which are necessary accessing in forest areas, is also of great importance from an environmental viewpoint as well as technical and economic manner. Forest road planning which can not be changed later and left a permanent mark on the natural environment carries much more importance to the environment especially on sloping land. This is because, it is important choosing correct type of roaf structure, and doing periodic maintenance of the roads. Skidding activities, after wood production, is important in terms of its impact on forest soil and by means of effects on saplings and trees on the releated forest areas.The development of environmental sensitive techniques is difficult, limited or expensive for this wood extraction works which are made more difficult conditons in the sloping terrain. Therefore, especially in using some silvicultural methods wood extraction damages are even greater. In this study; some road planning, road construction and wood extraction techniques which performed by me have been made to examine the environmental aspects. Environment-friendly forest roads and primary transport techniques on the forest ecosystem are briefly explained and discussed in the frame of the environmental aspects.

Construction and maintenance of underground mine roads

Energy Technology Data Exchange (ETDEWEB)

Logan, A.S.; Seedsman, R.W. [Coffey Partners International Pty. Ltd. (Australia)

1995-12-31

Good roads are essential in moving men and materials to and from the underground workplace. An underground coal industry funded project was recently completed on underground mine road construction and maintenance. This paper discusses practical approaches to construction and maintenance of underground mine roads using transferable civil technologies and innovative techniques. Mine pavements are generally low-cost (relative to civil roads), constructed to varying standards using locally available materials to best meet the mobility needs of the mine. Performance of pavements is thus largely dependent on the environmental conditions, quality of the available road making materials, maintenance policies and available resources. This paper explains the causes of bad roads in various underground environments. It details available management strategies, construction and water control techniques, road maintenance and vehicle considerations. It concludes that the trend to larger rubber tires mining equipment needs to be matched with construction and maintenance of high quality road surfaces. For large operations, the total cost due to poor roads may equate to in excess of $A1 million per annum. The strategies outlined in this paper provide the basis for construction and maintenance of underground mine roads to help achieve desired production targets. (author). 2 tabs., 4 figs., 7 refs.

Psychological aspects of road user behaviour

NARCIS (Netherlands)

Rothengatter, J.A.

The behaviour of road users is an important factor in accident causation. Traffic psychology, defined as ''the study of the behaviour of road users and the psychological processes underlying that behaviour'', attempts to identify the determinants of road user behaviour with the aim of developing

Road Infrastructure Safety Management in Poland

Science.gov (United States)

Budzynski, Marcin; Jamroz, Kazimierz; Kustra, Wojciech; Michalski, Lech; Gaca, Stanislaw

2017-10-01

The objective of road safety infrastructure management is to ensure that when roads are planned, designed, built and used road risks can be identified, assessed and mitigated. Road transport safety is significantly less developed than that of rail, water and air transport. The average individual risk of being a fatality in relation to the distance covered is thirty times higher in road transport that in the other modes. This is mainly because the different modes have a different approach to safety management and to the use of risk management methods and tools. In recent years Poland has had one of the European Union’s highest road death numbers. In 2016 there were 3026 fatalities on Polish roads with 40,766 injuries. Protecting road users from the risk of injury and death should be given top priority. While Poland’s national and regional road safety programmes address this problem and are instrumental in systematically reducing the number of casualties, the effects are far from the expectations. Modern approaches to safety focus on three integrated elements: infrastructure measures, safety management and safety culture. Due to its complexity, the process of road safety management requires modern tools to help with identifying road user risks, assess and evaluate the safety of road infrastructure and select effective measures to improve road safety. One possible tool for tackling this problem is the risk-based method for road infrastructure safety management. European Union Directive 2008/96/EC regulates and proposes a list of tools for managing road infrastructure safety. Road safety tools look at two criteria: the life cycle of a road structure and the process of risk management. Risk can be minimized through the application of the proposed interventions during design process as reasonable. The proposed methods of risk management bring together two stages: risk assessment and risk response occurring within the analyzed road structure (road network, road

Road safety analysis on Achmad Yani frontage road Surabaya

Science.gov (United States)

Machsus; Prayogo, I.; Chomaedhi; Hayati, D. W.; Utanaka, A.

2017-11-01

This research discusses road safety analysis on the operation of frontage road on the west side of Achmad Yani Road Surabaya. This research began by conducting survey on secondary data of traffic accidents. In addition, primary data survey was conducted to obtain traffic data, geometric road data, and other supporting data at the study site along the west side frontage of Ahmad Yani Road Surabaya. Devices used in this research include camera, handy cam, speed gun, counters of vehicles, rolling meter, computer and others. In outline, the stages to conduct this research are divided into 4 stages, namely 1.the preparation stage, 2.data collection and processing, 3. analysis and discussion, and 4. conclusion. The results of this study showed that the accident characteristics of the frontage road are (i) 3 accidents occured per month, (ii) motorcycles was accounted for the largest proportion of accidents which amounted to 74.6 percent, (iii) there were 3 accident victims per month, and (iv) material losses per month worths 1.2 million. The accident rate in 2016 was 0.04 crashes per one million vehicle travels per kilometer, while during 2 months in 2017 it was 0.15 accidents per one million vehicle travels per kilometer. Black spot area of accident is located on Sta 2 + 800 to 2 + 900 which is in front of Graha Pena building and DBL Arena. The high rate of accidents is influenced by the speed of the vehicle which 85 percentile exceeds the speed limit of 40km per hour.

Does the Maya Forest Need More Roads?:Conservation Policy in Brief

OpenAIRE

Conde, Dalia Amor; Ramos, Victor Hugo; Burgués, Irene; Castellanos, Bayron; Fleck, Leonardo; Albacete, Carlos; Espinoza, Piedad; Manterola, Carlos; Paiz, Gerardo

2007-01-01

An assortment of road projects has been proposed in the border region of Mexico, Guatemala and Belize, which is part of the Maya Forest, the largest contiguous tropical forest in the Americas north of the Amazon. The proposals are apparently aimed at spurring economic growth and reducing the high levels of poverty found in this area. But more and better roads usually bring more people and expand farms. Decision-makers are therefore confronted with a seeming conflict between conservation and d...

Emissions of road transport

International Nuclear Information System (INIS)

Maekelae, K.; Tuominen, A.

2001-01-01

Information on the emissions and energy consumption of different vehicles per transported amount of goods has up to last years been minimal. The unit emissions mean the amount of harmful compounds in the flue gases of a vehicle per service, time or energy unit. National three-year MOBILE 2-research program, started in 1999, determines the unit emissions of all the traffic sectors in Finland. VTT Building and Transport mainly carry out the research, but the Institute of Transportation Engineering of the Tampere University of Technology (TTKK) is responsible for a part of the research. The objective of the project is to create common rules for the determination of unit emissions values, and to determine the best possible values for Finnish conditions. Unit emission data is mainly needed for evaluation of the environmental impacts of production plants and other activities containing transportation of commodities. At the web sites of VTT Building and Transport there are about 60 pages of text and tables (about 4000 values) on unit emissions. The URL of the pages is http://www.vtt.fi/rte/projects/lipastoe/index.htm. These web pages present data on all the transportation sectors (road, railroad, water and air transportation), most of the materials concerning road transportation. Following compounds and values are included: CO, HC, NO x , particulates, SO 2 , CO 2 and energy consumption. Methane and nitrous oxide emissions values have also been presented

Safety impacts of rural road construction

Science.gov (United States)

2001-02-01

Crash data in Kentucky show that the fatal crash rate on two-lane rural roads is substantially higher than on any other type of road. Improvements have been proposed at some locations on this type of road which involve either upgrading the existing t...

PROPOSAL OF VOIVODESHIP ROAD SAFETY IMPROVEMENT PROGRAMME

OpenAIRE

Tomasz SZCZURASZEK; Jan KEMPA

2016-01-01

The article presents a proposal of the ‘GAMBIT KUJAWSKO-POMORSKI’ Road Safety Improvement Programme. The main idea of the Programme is to establish and initiate systems that will be responsible for the most important areas of activity within road safety, including road safety control, supervision, and management systems in the whole Voivodeship. In total, the creation and start of nine such systems has been proposed, namely: the Road Safety Management, the Integrated Road Rescue Service, the ...

Recognizablility of rural roads in the Netherlands.

NARCIS (Netherlands)

Aarts, L.T. & Davidse, R.J.

2008-01-01

In the Netherlands, the Sustainable Safety vision is an important guide in improving road safety. It is considered that the road environment shouldconform to the expectations of road users in order to prevent errors thatcould lead to road crashes. These expectations are based on the characteristics

Comparing Environmental Impact Assessment (EIA) in Poland and Denmark for Road Construction in Relation to Wildlife and Nature Protection : Report for Poland

DEFF Research Database (Denmark)

Sienkiewicz, J.; Adrados, L. C.; Briggs, L

Project : Fauna Passages under Selected Roads in Poland - Education, Monitoring and Construction - Part A. DANCEE M124/031-0212......Project : Fauna Passages under Selected Roads in Poland - Education, Monitoring and Construction - Part A. DANCEE M124/031-0212...

Dynamics of vehicle-road coupled system

CERN Document Server

Yang, Shaopu; Li, Shaohua

2015-01-01

Vehicle dynamics and road dynamics are usually considered to be two largely independent subjects. In vehicle dynamics, road surface roughness is generally regarded as random excitation of the vehicle, while in road dynamics, the vehicle is generally regarded as a moving load acting on the pavement. This book suggests a new research concept to integrate the vehicle and the road system with the help of a tire model, and establishes a cross-subject research framework dubbed vehicle-pavement coupled system dynamics. In this context, the dynamics of the vehicle, road and the vehicle-road coupled system are investigated by means of theoretical analysis, numerical simulations and field tests. This book will be a valuable resource for university professors, graduate students and engineers majoring in automotive design, mechanical engineering, highway engineering and other related areas. Shaopu Yang is a professor and deputy president of Shijiazhuang Tiedao University, China; Liqun Chen is a professor at Shanghai Univ...

Multiple stakeholders in road pricing: A game theoretic approach

NARCIS (Netherlands)

Ohazulike, Anthony; Still, Georg J.; Kern, Walter; van Berkum, Eric C.; Hausken, Kjell; Zhuang, Jun

2015-01-01

We investigate a game theoretic approach as an alternative to the standard multi-objective optimization models for road pricing. Assuming that various, partly conflicting traffic externalities (congestion, air pollution, noise, safety, etcetera) are represented by corresponding players acting on a

An Analysis of Stand-alone GPS Quality and Simulated GNSS Quality for Road Pricing

DEFF Research Database (Denmark)

Zabic, Martina; Nielsen, Otto Anker

2006-01-01

Use of GPS for road pricing has often been suggested as the way of creating more efficient charging strategies than existing systems based on cordon lines or time use. In Denmark, Copenhagen participated with the AKTA project in the PRoGRESS programme, sponsored by the EU. The major part...... of the AKTA project was to equip 500 cars with GPS receivers. The paper presents the methods and results from a study of GPS quality in relation to road pricing in a dense urban area. The collected data from 500 cars over a two-year period in the Copenhagen region was analyzed in order to determine whether...... the stand alone GPS quality and reliability is adequate for implementation of an operational road pricing system in Copenhagen. The results from the analysis show that the satellite availability in Copenhagen is not sufficient to form the basis for a reliable operational road pricing system. The narrow...

Problematics of Reliability of Road Rollers

Science.gov (United States)

Stawowiak, Michał; Kuczaj, Mariusz

2018-06-01

This article refers to the reliability of road rollers used in a selected roadworks company. Information on the method of road rollers service and how the service affects the reliability of these rollers is presented. Attention was paid to the process of the implemented maintenance plan with regard to the machine's operational time. The reliability of road rollers was analyzed by determining and interpreting readiness coefficients.

Vehicle Speed Determination in Case of Road Accident by Software Method and Comparing of Results with the Mathematical Model

Directory of Open Access Journals (Sweden)

Hoxha Gezim

2017-11-01

Full Text Available The paper addresses the problem to vehicle speed calculation at road accidents. To determine the speed are used the PC Crash software and Virtual Crash. With both methods are analysed concrete cases of road accidents. Calculation methods and comparing results are present for analyse. These methods consider several factors such are: the front part of the vehicle, the technical feature of the vehicle, car angle, remote relocation after the crash, road conditions etc. Expected results with PC Crash software and Virtual Crash are shown in tabular graphics and compared in mathematical methods.

Global patterns of current and future road infrastructure

Science.gov (United States)

Meijer, Johan R.; Huijbregts, Mark A. J.; Schotten, Kees C. G. J.; Schipper, Aafke M.

2018-06-01

Georeferenced information on road infrastructure is essential for spatial planning, socio-economic assessments and environmental impact analyses. Yet current global road maps are typically outdated or characterized by spatial bias in coverage. In the Global Roads Inventory Project we gathered, harmonized and integrated nearly 60 geospatial datasets on road infrastructure into a global roads dataset. The resulting dataset covers 222 countries and includes over 21 million km of roads, which is two to three times the total length in the currently best available country-based global roads datasets. We then related total road length per country to country area, population density, GDP and OECD membership, resulting in a regression model with adjusted R 2 of 0.90, and found that that the highest road densities are associated with densely populated and wealthier countries. Applying our regression model to future population densities and GDP estimates from the Shared Socioeconomic Pathway (SSP) scenarios, we obtained a tentative estimate of 3.0–4.7 million km additional road length for the year 2050. Large increases in road length were projected for developing nations in some of the world’s last remaining wilderness areas, such as the Amazon, the Congo basin and New Guinea. This highlights the need for accurate spatial road datasets to underpin strategic spatial planning in order to reduce the impacts of roads in remaining pristine ecosystems.

Numerical modelling of flexible pavement incorporating cross-anisotropic material properties. Part II: Surface rectangular loading

OpenAIRE

Maina, J W; Kawana, F; Matsui, K

2017-01-01

In order to better understand the impact of increased loading on roads, studies on tyre-road interaction have gained prominence in recent years. Tyres form an essential interface between vehicles and road pavement surfaces. These are the only parts of the vehicle that are in contact with the road and transmit the vehicle loading to the road surface. The use of the Cartesian coordinate system is convenient in dealing with a uniform/non-uniform tyre load acting over a rectangular area, but few ...

Road Accidents and Road Fatalities in Denmark from 1968 to 2004

DEFF Research Database (Denmark)

Orozova-Bekkevold, Ivanka; Hels, Tove; Bernhoft, Inger Marie

2008-01-01

The purpose of this article is to describe the road accidents and road fatalities in Denmark in the period 1968-2004. Only accidents registered by the police were used. Crude and gender & age specific fatality rates (counts per 1,000,000 inhabitants) were estimated for all road users...... and for bicyclists. The accident and fatality rates have decreased by around 70% from 1968 to 2004, while the motorisation rate has increased by approximately 90%. The sharpest decrease in the fatality rate was observed among the youngest (below 18 years old) and the older (above 64) road users. Gender related...... and actions targeted to improve road safety have indeed led to a significant reduction in injury accidents and fatalities. Further research and more detailed data, especially on traffic volume and individual exposure are necessary in order to investigate properly a causal relation between the number...

Overload road damage model

CSIR Research Space (South Africa)

Roux, MP

2005-03-01

Full Text Available Not only do overloaded vehicles pose an increased safety risk on the road (reduced stability and braking efficiency etc.), but they also accelerate the rate of deterioration of the road network and increase road maintenance costs, which in turn...

PHOTOGRAMMETRIC TECHNIQUES FOR ROAD SURFACE ANALYSIS

Directory of Open Access Journals (Sweden)

V. A. Knyaz

2016-06-01

Full Text Available The quality and condition of a road surface is of great importance for convenience and safety of driving. So the investigations of the behaviour of road materials in laboratory conditions and monitoring of existing roads are widely fulfilled for controlling a geometric parameters and detecting defects in the road surface. Photogrammetry as accurate non-contact measuring method provides powerful means for solving different tasks in road surface reconstruction and analysis. The range of dimensions concerned in road surface analysis can have great variation from tenths of millimetre to hundreds meters and more. So a set of techniques is needed to meet all requirements of road parameters estimation. Two photogrammetric techniques for road surface analysis are presented: for accurate measuring of road pavement and for road surface reconstruction based on imagery obtained from unmanned aerial vehicle. The first technique uses photogrammetric system based on structured light for fast and accurate surface 3D reconstruction and it allows analysing the characteristics of road texture and monitoring the pavement behaviour. The second technique provides dense 3D model road suitable for road macro parameters estimation.

Road dust emissions from paved roads measured using different mobile systems.

Science.gov (United States)

Pirjola, Liisa; Johansson, Christer; Kupiainen, Kaarle; Stojiljkovic, Ana; Karlsson, Hans; Hussein, Tareq

2010-12-01

Very few real-world measurements of road dust suspension have been performed to date. This study compares two different techniques (referred to as Sniffer and Emma) to measure road dust emissions. The main differences between the systems are the construction of the inlet, different instruments for recording particulate matter (PM) levels, and different loads on the wheel axes (the weight of Sniffer was much higher than that of Emma). Both systems showed substantial small-scale variations of emission levels along the road, likely depending on-road surface conditions. The variations observed correlated quite well, and the discrepancies are likely a result of variations in dust load on the road surface perpendicular to the driving direction that cause variations in the measurements depending on slightly different paths driven by the two vehicles. Both systems showed a substantial influence on the emission levels depending on the type of tire used. The summer tire showed much lower suspension than the winter tires (one nonstudded and one studded). However, the relative importance of the nonstudded versus studded tire was rather different. For the ratio of studded/nonstudded, Emma shows higher values on all road sections compared with Sniffer. Both techniques showed increased emission levels with increasing vehicle speed. When the speed increased from 50 to 80 km hr(-1), the relative concentrations increased by 30-170% depending on the tire type and dust load. However, for road sections that were very dirty, Sniffer showed a much higher relative increase in the emission level with the nonstudded tire. Sniffer's absolute concentrations were mostly higher than Emma's. Possible reasons for the differences are discussed in the paper. Both systems can be used for studying relative road dust emissions and for designing air quality management strategies.

Future Road Density

Data.gov (United States)

U.S. Environmental Protection Agency — Road density is generally highly correlated with amount of developed land cover. High road densities usually indicate high levels of ecological disturbance. More...

Road traffic congestion a concise guide

CERN Document Server

Falcocchio, John C

2015-01-01

This book on road traffic congestion in cities and suburbs describes congestion problems and shows how they can be relieved. The first part (Chapters 1 - 3) shows how congestion reflects transportation technologies and settlement patterns. The second part (Chapters 4 - 13) describes the causes, characteristics, and consequences of congestion. The third part (Chapters 14 - 23) presents various relief strategies - including supply adaptation and demand mitigation - for nonrecurring and recurring congestion. The last part (Chapter 24) gives general guidelines for congestion relief and provides a general outlook for the future. The book will be useful for a wide audience - including students, practitioners and researchers in a variety of professional endeavors: traffic engineers, transportation planners, public transport specialists, city planners, public administrators, and private enterprises that depend on transportation for their activities.  

Spatial Analysis Methods of Road Traffic Collisions

DEFF Research Database (Denmark)

Loo, Becky P. Y.; Anderson, Tessa Kate

Spatial Analysis Methods of Road Traffic Collisions centers on the geographical nature of road crashes, and uses spatial methods to provide a greater understanding of the patterns and processes that cause them. Written by internationally known experts in the field of transport geography, the book...... outlines the key issues in identifying hazardous road locations (HRLs), considers current approaches used for reducing and preventing road traffic collisions, and outlines a strategy for improved road safety. The book covers spatial accuracy, validation, and other statistical issues, as well as link...

Analysis of Individual and Environmental Factors for Road Traffic Accidents in Sirjan-Bandarabbas Road between 2010 and 2011, Iran

Directory of Open Access Journals (Sweden)

Ghorbanali Mohammadi

2016-10-01

Full Text Available Sirjan -Bandarabbas road is one of the important commercial roads in Iran and for Sirjan’s area situation and relevance between Sirjan and other states in Iran so high percentage of goods that forwarded from Bandarabbas to other states transit from Sirjan .Therefore this road is as one important transition road and traffic road too .This study analyzed road traffic accidents were occurred between 2010 and 201in Sirjan- Bandarabbas road. Individual and demographic factors include Time of accidents, Drivers age, time of the days, seat belt and safety laws, Guilty vehicle, Mode of accident and education Level. Time of day analyses suggested that the highest percentage of road traffic injuries occurred in the time group between 12-18 hours. Drivers with the age group of 36-50 had more involvement in death accidents. The findings of this study also revealed that most of the collisions was front to back and front to side. Female drivers were found to be generally safer drivers than their male counterparts; male drivers had a higher involvement rate in road traffic accidents. This study indicated that Observe safety laws, Guilty vehicle and Mode of accidents have a meaningful relationship with Type of accidents in road traffic accidents in Sirjan Bandarabbas road.

Road Traffic Accidents - The Number One Killer in Libya

Directory of Open Access Journals (Sweden)

Abdulmajid Ahmed Ali

2007-01-01

Full Text Available To The Editor: It is estimated that 1.26 million people worldwide died in 2000 from road traffic accidents, 90% of them in low and middle-income countries. In 2000, the road traffic injury mortality rate for the world was 20.8 per 100,000 populations (30.8 in males, 11.0 in females [1].The Arab population constitutes 3.6% of the world’s population and it owns 1% of the world’s vehicles. Its human losses as a result of road traffic accidents (RTA account for 4.8% of that of the world’s losses [2]. It is estimated that the annual cost of road crashes is about 1% of the Gross National Product (GNP in developing countries, 1.5 in transitional countries and 2% in highly motorised countries [3].In Libya the situation is worse. It is a sad fact that road traffic accidents are the number one killer in Libya. As a matter of fact I consider it to be an ‘epidemic’ in all sectors of the Libyan society. There is not a day that goes by in Libya without us hearing about families, young men, women and children getting killed in horrific car accidents.It is alarming that young children are knocked down on a daily basis by speeding young drivers, whose understanding of driving skills may have been acquired from "playstation games"! (You can watch some of the shameful video clips sent by some of these drivers on this link http://www.youtube.com/watch?v=doWEDjiHlVoI feel it is our responsibility as physicians observing the situation to raise awareness about the scale of the problem, possible causes, and how to tackle it. POSSIBLE CAUSES:• A driving licence in Libya is not issued on the basis of how much you know. Therefore the majority of drivers know little or nothing about the law.• Wearing seat belts is not compulsory in most parts of Libya. In some places, especially in the Eastern part of Libya, you could be penalised for wearing one. I was stopped many years ago by the traffic police in the Eastern part of Libya because I was wearing sunglasses

Road design and environment : best practice on self-explaining and forgiving roads. Deliverable D3 of the RiPCORD-iSEREST project (Road Infrastructure Safety Protection - Core-Research and Development for Road Safety in Europe; Increasing safety and reliability of secondary roads for a sustainable Surface Transport).

NARCIS (Netherlands)

Matena, S. Louwerse, W. Schermers, G. Vaneerdewegh, P. Pokorny, P. Gaitanidou, L. Elvik, R. & Cardoso, J.

2009-01-01

Main objective of work-package 3 of Ripcord-lserest was to collect information on best practices concerning the design of self-explaining and forgiving roads. In order to gain an overview on existing practises on road categorisation and the layout of typical rural roads a questionnaire survey had

A randomized controlled trial of “Sikker Trafik LIVE” (“Road Safety LIVE”) – Sub-report 1

DEFF Research Database (Denmark)

Hansen, Helle; Sandoy, Tróndur Møller; Kristensen, Christian Li

2018-01-01

This report presents the impact measurement for “Sikker Trafik LIVE” (“Road Safety LIVE”), an educational intervention carried out by the Danish Road Safety Council. The impact measurement concerns the part of the intervention aimed at the oldest pupils at primary and lower secondary schools: 8th...... to 10th grades (13-17 years old). The purpose of the LIVE intervention is to provide pupils with more insight into and a better understanding of the consequences of a serious road accident, and to focus attention on the choices pupils make in traffic. The aim is to motivate pupils to make safer choices...

Topography and the road network in the territory of ancient Naissus

Directory of Open Access Journals (Sweden)

Ljubomirović Irena V.

2016-01-01

Full Text Available Archaeological research revealed that ancient Naissus was located on the right bank of the Nišava, on the territory partially covered by the Niš Fortress. The ancient town developed on a wide and flat terrain, which offered good conditions for settlement, but also for raising fortifications. According to modern scholars, the urban settlement on the right bank of the Nišava was preceded by a small native village (vicus, which was important for the erection of the town fortifications. Numerous roads were linking Naissus with the surrounding regions and villas in the county side. We learn about them on the basis of epigraphic and archaeological material milestones and remains of roads, but also on the basis of the location of the necropolises, which in the classical period often sprang up near the suburban roads. The road leading to the east crossed the Nišava by a stone bridge, whose remains were visible not far from today's 'Benetton' factory. The road led further over 'Gabrovac land', intersected with streams over which the remains of three stone bridges from the Roman period were found. This route led to Mediana, a suburb with villas three miles distant from the city. Another important road connecting the region Pomoravlje with the southern parts of the province of Dalmatia was the road Naissus-Lissus. TA section leding to Macedonia and the harbour of Thessalonica over Scupi branched from it south of Naissus: Ad Herculem, Hammeum Ad Fines, Vindenae and Vicianum. From Vicianum station (Vučitrn one section ran towards Lissus and another towards Scupi. Throughout the Timok valley stretched one of the most important roads (Naissus-Ratiaria that linked Naissus and the central Balkan areas with the region of Podunavlje (the Danube basin. The road led from Naissus to the East, along the right bank of the Nišava (across the areas of Jagodin mala and Vrežina and, at the modern village of Malča, it turned towards the North, following the route of

Investigation of road network features and safety performance.

Science.gov (United States)

Wang, Xuesong; Wu, Xingwei; Abdel-Aty, Mohamed; Tremont, Paul J

2013-07-01

The analysis of road network designs can provide useful information to transportation planners as they seek to improve the safety of road networks. The objectives of this study were to compare and define the effective road network indices and to analyze the relationship between road network structure and traffic safety at the level of the Traffic Analysis Zone (TAZ). One problem in comparing different road networks is establishing criteria that can be used to scale networks in terms of their structures. Based on data from Orange and Hillsborough Counties in Florida, road network structural properties within TAZs were scaled using 3 indices: Closeness Centrality, Betweenness Centrality, and Meshedness Coefficient. The Meshedness Coefficient performed best in capturing the structural features of the road network. Bayesian Conditional Autoregressive (CAR) models were developed to assess the safety of various network configurations as measured by total crashes, crashes on state roads, and crashes on local roads. The models' results showed that crash frequencies on local roads were closely related to factors within the TAZs (e.g., zonal network structure, TAZ population), while crash frequencies on state roads were closely related to the road and traffic features of state roads. For the safety effects of different networks, the Grid type was associated with the highest frequency of crashes, followed by the Mixed type, the Loops & Lollipops type, and the Sparse type. This study shows that it is possible to develop a quantitative scale for structural properties of a road network, and to use that scale to calculate the relationships between network structural properties and safety. Copyright © 2013 Elsevier Ltd. All rights reserved.

The study of technological prevention method of road accident ...

African Journals Online (AJOL)

The study of technological prevention method of road accident related to driver and vehicle. ... road accident prevention method based on the factors studied. The study of this paper can provide forceful data analysis support for the road traffic safety related research. Keywords: road accident; accident prevention; road safety.

South Fence Road -- Phase 1 field operations summary

Energy Technology Data Exchange (ETDEWEB)

McCord, J.P. [INTERA, Inc., Albuquerque, NM (United States); Neel, D. [GRAM, Inc., Albuquerque, NM (United States)

1996-03-01

The South Fence Road (SFR) project is part of the Sandia National Laboratories, New Mexico (SNL/NM) Site-Wide Hydrogeologic Characterization (SWHC) task. The SWHC task has as its objective the reduction of uncertainty about the rate and direction of groundwater flow in the SNL/NM/Kirtland Air Force Base (KAFB) area. The SFR project area is located along the southern boundary of SNL/KAFB. This project area was selected to provide site-specific information related to geology and groundwater hydrology within the Hubbell Spring/Tijeras/Sandia fault complex. Specific objectives included determining the depth to the Santa Fe Group/bedrock contact, the depth to the water table, and the hydrogeologic complexities related to faulting. This report is a basic data report from the first phase of field operations associated with the drilling, logging, completion, and development of South Fence Road Wells SFR-1D and SFR-1S, SFR-2, SFR-3D and SFR-3S, and SFR-4. These test/monitoring wells were installed as part of Sandia National Laboratories, New Mexico, Environmental Restoration Project.

South Fence Road -- Phase 1 field operations summary

International Nuclear Information System (INIS)

McCord, J.P.; Neel, D.

1996-03-01

The South Fence Road (SFR) project is part of the Sandia National Laboratories, New Mexico (SNL/NM) Site-Wide Hydrogeologic Characterization (SWHC) task. The SWHC task has as its objective the reduction of uncertainty about the rate and direction of groundwater flow in the SNL/NM/Kirtland Air Force Base (KAFB) area. The SFR project area is located along the southern boundary of SNL/KAFB. This project area was selected to provide site-specific information related to geology and groundwater hydrology within the Hubbell Spring/Tijeras/Sandia fault complex. Specific objectives included determining the depth to the Santa Fe Group/bedrock contact, the depth to the water table, and the hydrogeologic complexities related to faulting. This report is a basic data report from the first phase of field operations associated with the drilling, logging, completion, and development of South Fence Road Wells SFR-1D and SFR-1S, SFR-2, SFR-3D and SFR-3S, and SFR-4. These test/monitoring wells were installed as part of Sandia National Laboratories, New Mexico, Environmental Restoration Project

Response of moose to a high‐density road network

Science.gov (United States)

Wattles, David W.; Zeller, Katherine A.; DeStefano, Stephen

2018-01-01

Road networks and the disturbance associated with vehicle traffic alter animal behavior, movements, and habitat selection. The response of moose (Alces americanus) to roads has been documented in relatively rural areas, but less is known about moose response to roads in more highly roaded landscapes. We examined road‐crossing frequencies and habitat use of global positioning system (GPS)‐collared moose in Massachusetts, USA, where moose home ranges have road densities approximately twice that of previous studies. We compared seasonal road‐crossing frequencies of moose with a null movement model. We estimated moose travel speeds during road‐crossing events and compared them with speeds during other home range movements. To estimate the extent of the road effect zone and determine how roads influenced moose habitat use, we fit a third‐order resource selection function. With the exception of the lowest use road class (roads less than expected based on the null movement model and frequency decreased with increasing road size and traffic. Moose crossed roads faster than they traveled during other times. This effect increased with increasing road use intensity. Overall, roads were a major factor determining what portions of Massachusetts moose used and how they moved among habitat patches. Our results suggest that moose in Massachusetts can adapt to a high‐density road network, but the road effect is still strongly negative and, in some cases, is more pronounced than in study areas with lower road densities. Future road construction and the expansion of road networks may have a large effect on moose and other wildlife.

Forest soil erosion prediction as influenced by wildfire and roads

Science.gov (United States)

Cao, L.; Brooks, E. S.; Elliot, W.

2017-12-01

Following a wildfire, the risk of erosion is greatly increased. Forest road networks may change the underlying topography and alter natural flow paths. Flow accumulation and energy can be redistributed by roads and alter soil erosion processes. A LiDAR (Light Detection and Ranging) DEM makes it possible to quantify road topography, and estimate how roads influence surface runoff and sediment transport in a fire-disturbed watershed. With GIS technology and a soil erosion model, this study was carried out to evaluate the effect of roads on erosion and sediment yield following the Emerald Fire southwest of Lake Tahoe. The GeoWEPP model was used to estimate onsite erosion and offsite sediment delivery from each hillslope polygon and channel segment before and after fire disturbance in part of the burned area. The GeoWEPP flow path method was used to estimate the post-fire erosion rate of each GIS pixel. A 2-m resolution LiDAR DEM was used as the terrain layer. The Emerald Fire greatly increased onsite soil loss and sediment yields within the fire boundary. Following the fire, 78.71% of the burned area had predicted sediment yields greater than 4 Mg/ha/yr, compared to the preburn condition when 65.3% of the study area was estimated to generate a sediment yield less than 0.25 Mg/ha/yr. Roads had a remarkable influence on the flow path simulation and sub-catchments delineation, affecting sediment transport process spatially. Road segments acted as barriers that intercepted overland runoff and reduced downslope flow energy accumulation, therefore reducing onsite soil loss downslope of the road. Roads also changed the boundary of sub-catchment and defined new hydrological units. Road segments can transport sediment from one sub-catchment to another. This in turn leads to the redistribution of sediment and alters sediment yield for some sub-catchments. Culverts and road drain systems are of vital importance in rerouting runoff and sediment. Conservation structures can be

Use of wood ash for road stabilisation

International Nuclear Information System (INIS)

Lagerkvist, A.; Lind, B.

2009-01-01

Due to warmer winters in Sweden, the bearing capacity of forestry roads has become increasingly problematic in recent years. Road stabilization is needed in order to get timber out from the forests. This usually involves the addition of cement to the road body. However, wood ash is a possible substitute for cement because it has similar properties. Using wood ash has the added advantage of saving landfill space. This paper presented an ongoing laboratory study on leaching and mechanical stability, as well as frost-sensitivity using a 30 per cent ash addition to natural soils for reinforcing a forestry road near Timra in central Sweden. The road was being monitored with regard to environmental impact and mechanical properties. The paper discussed the potential of biofuel ashes and the increasing need to reinforce infrastructure due to climate change. The environmental impact from ash use in road constructions was then addressed. It was concluded that the application of ash in road construction would help to strengthen forest roads, make them more resistant to climatic change and render them accessible year-round. 32 refs., 3 tabs., 2 figs.

Cost of skid roads for arch logging in West Virginia

Science.gov (United States)

George R., Jr. Trimble; Carl R. Barr

1960-01-01

In the mountain hardwood country of the northern Appalachians, tree-length skidding with tractor and arch has proved to be economical logging. One essential part of this type of logging is that tree-length logs are winched to the skid roads: tractor and arch do not run around through the woods. Winching distance is commonly 200 to 300 feet; and occasionally an extra...

RoADS: A road pavement monitoring system for anomaly detection using smart phones

NARCIS (Netherlands)

Seraj, Fatjon; van der Zwaag, B.J.; Dilo, Arta; Luarasi, Tamara; Havinga, Paul J.M.; Atzmueller, Martin; Chin, Alvin; Janssen, Frederik; Schweizer, Immanuel; Trattner, Christoph

2016-01-01

Monitoring the road pavement is a challenging task. Authorities spend time and finances to monitor the state and quality of the road pavement. This paper investigate road surface monitoring with smartphones equipped with GPS and inertial sensors: accelerometer and gyroscope. In this study we

RoADS: A road pavement monitoring system for anomaly detection using smart phones

NARCIS (Netherlands)

Seraj, Fatjon; van der Zwaag, B.J.; Dilo, Arta; Luarasi, Tamara; Havinga, Paul J.M.

2014-01-01

Monitoring the road pavement is a challenging task. Authorities spend time and finances to monitor the state and quality of the road pavement. This paper investigate road surface monitoring with smartphones equipped with GPS and inertial sensors: accelerometer and gyroscope. In this study we

Influence of Excessive Moisture in the Subgrade on the Durability and Load-Bearing Capacity of Road Pavements

Science.gov (United States)

Mieczkowski, P.; Budziński, B.

2018-05-01

When well performed, pavement renewal or alteration shall ensure the desired properties of the road during the assumed period of operation. Presence of water in the subgrade can be one of the main factors affecting the structural capacity of pavement and can result in cracking of the bituminous layers, even after a very short period of trafficking. Reconstruction of one of regional roads in Poland has been chosen to serve as an example of inappropriate approach to the problem of the presence of water in the road structure. The project included construction of new layers of pavement and increasing the design life of the whole pavement structure to 4.06 million ESAL of 100 kN (as per the Standard Catalogue of Typical Flexible and Semi-rigid Road Pavement Structures, issue of 1997). After a relatively short period of trafficking (3-5 years) localised alligator cracking appeared on the surface along with structural deformations. The pavement condition assessment including FWD tests was carried out to reveal excessive deflections (over 500 μm) which classify the road for renewal. The analysis of data showed that the main cause of distress was softening of the subgrade caused by an ingress of precipitation water under the pavement layers through the roadway and shoulder edges. The deficiencies of the performed reconstruction occurred both in the roadway (including small step-outs in the cement-treated layer) and partly in the shoulders where the existing soil was in places replaced with impervious material, with the existing (cohesive) material left in place on a major part of the overall length.

Deterioration of flood affected Queensland roads – An investigative study

Directory of Open Access Journals (Sweden)

Masuda Sultana

2016-11-01

Full Text Available The aim of this paper was to investigate the impact of recent flooding events on the structural and surface condition (such as roughness and rutting of the pavements of the Department of Transport and Main Roads, Queensland, and the Brisbane City Council. The paper also reviewed the major flooding and cyclone events that occurred in the last six years in Queensland. Generally, a rapid increase in deterioration of the structural and surface conditions such as roughness and rutting was observed in pavements after the flood as a result of the inundation. An increasing need for road rehabilitation was also observed after the recent flooding events from 2010 to 2015 in Queensland. Assessing the rapid deterioration of the structural and surface condition of the flood affected pavements is a prerequisite for the accurate prediction of pavement performance, a better decision making process and the management of these roads. Although this paper did not include any model for roughness and rutting, deterioration models for roughness and rutting of flood affected pavements are currently being developed as a part of the future scope of this research. Keywords: Pavement deterioration, Flooding, Structural and surface condition

Road pricing, air pollution and external costs; Road pricing, luftforurening og eksternalitetsomkostninger

Energy Technology Data Exchange (ETDEWEB)

Solvang Jensen, S.; Ketzel, M. (Aarhus Univ., Danmarks Miljoeundersoegelser, Afd. for Atmosfaerisk Miljoe, Roskilde (Denmark)); Skou Andersen, M. (Aarhus Univ., Danmarks Miljoeundersoegelser, Afd. for Systemanalyse, Roskilde (Denmark))

2010-06-15

The objective of this assessment is to improve the foundation for decision-making about introduction of a road pricing system that aims to reduce the health impacts and social costs of traffic-related air pollution. The analysis focuses on how road emissions, air quality, population exposure, and social costs of air pollution depend on geography (different city sizes and rural areas) and time of the day (rush hours versus non-rush hours). A review of Danish studies related to road pricing has also been carried out to assess the expected effect of road pricing on traffic performance (km travelled), vehicle composition and speed that are factors affecting air pollution. (LN)

Skid resistance determination for pavement management and wet-weather road safety

Directory of Open Access Journals (Sweden)

T.F. Fwa

2017-09-01

Full Text Available Road accidents during wet weather have been a topic of major concern of road engineers in regions of wet-tropical climate and in other parts of the world during the wet season of the year. Road safety studies indicate that approximately 20% of all road accidents occurred during wet weather, and that the skid resistance of wet pavements have a major influence on the occurrences of wet-weather accidents. Monitoring of wet pavement skid resistance has been an integral part of a typical pavement management system. However, because of the lack of prediction capability of pavement skid resistance under various rainfall intensities, the minimum skid resistance threshold for safe wet-weather driving has been specified by highway agencies based on either engineering judgement or past experience. It is shown in this paper that the single-point minimum skid resistance threshold is inadequate to offer a complete description of the skid resistance performance of the pavement sections in question for effective management of a road network. It is unable to assess the risk involved in an actual wet-weather condition where the pavement surface water-film thickness and vehicle speed are different from standard test conditions. This limitation of the current system of specifying a minimum skid resistance threshold can be overcome by adopting a theoretically sound approach to represent pavement skid resistance under different conditions of water-film thickness and vehicle speed. This paper describes the theoretical basis of the approach and the development of a mechanistically derived three-dimensional finite-element skid resistance simulation model to predict skid resistance. The application of the proposed approach and the skid resistance prediction procedure in pavement management system and wet-weather driving safety assessment is presented.

Roads Near Streams

Data.gov (United States)

U.S. Environmental Protection Agency — Roads are a source of auto related pollutants (e.g. gasoline, oil and other engine fluids). When roads are near streams, rain can wash these pollutants directly into...

Roads at risk: traffic detours from debris flows in southern Norway

Science.gov (United States)

Meyer, N. K.; Schwanghart, W.; Korup, O.; Nadim, F.

2015-05-01

Globalisation and interregional exchange of people, goods, and services has boosted the importance of and reliance on all kinds of transport networks. The linear structure of road networks is especially sensitive to natural hazards. In southern Norway, steep topography and extreme weather events promote frequent traffic disruption caused by debris flows. Topographic susceptibility and trigger frequency maps serve as input into a hazard appraisal at the scale of first-order catchments to quantify the impact of debris flows on the road network in terms of a failure likelihood of each link connecting two network vertices, e.g. road junctions. We compute total additional traffic loads as a function of traffic volume and excess distance, i.e. the extra length of an alternative path connecting two previously disrupted network vertices using a shortest-path algorithm. Our risk metric of link failure is the total additional annual traffic load, expressed as vehicle kilometres, because of debris-flow-related road closures. We present two scenarios demonstrating the impact of debris flows on the road network and quantify the associated path-failure likelihood between major cities in southern Norway. The scenarios indicate that major routes crossing the central and north-western part of the study area are associated with high link-failure risk. Yet options for detours on major routes are manifold and incur only little additional costs provided that drivers are sufficiently well informed about road closures. Our risk estimates may be of importance to road network managers and transport companies relying on speedy delivery of services and goods.

Exploring schema-driven differences in situation awareness between road users: an on-road study of driver, cyclist and motorcyclist situation awareness.

Science.gov (United States)

Salmon, Paul M; Lenne, Michael G; Walker, Guy H; Stanton, Neville A; Filtness, Ashleigh

2014-01-01

Collisions between different road users make a substantial contribution to road trauma. Although evidence suggests that different road users interpret the same road situations differently, it is not clear how road users' situation awareness differs, nor is it clear which differences might lead to conflicts. This article presents the findings from an on-road study conducted to examine driver, motorcyclist and cyclist situation awareness in different road environments. The findings suggest that, in addition to minor differences in the structure of different road users' situation awareness (i.e. amount of information and how it is integrated), the actual content of situation awareness in terms of road user schemata, the resulting interaction with the world and the information underpinning situation awareness is markedly different. Further examination indicates that the differences are likely to be compatible along arterial roads, shopping strips and at roundabouts, but that they may create conflicts between different road users at intersections. Interventions designed to support compatible situation awareness and behaviour between different road users are discussed.

Driving and off-road impairments underlying failure on road testing in Parkinson's disease.

Science.gov (United States)

Devos, Hannes; Vandenberghe, Wim; Tant, Mark; Akinwuntan, Abiodun E; De Weerdt, Willy; Nieuwboer, Alice; Uc, Ergun Y

2013-12-01

Parkinson's disease (PD) affects driving ability. We aimed to determine the most critical impairments in specific road skills and in clinical characteristics leading to failure on a road test in PD. In this cross-sectional study, certified driving assessment experts evaluated specific driving skills in 104 active, licensed drivers with PD using a standardized, on-road checklist and issued a global decision of pass/fail. Participants also completed an off-road evaluation assessing demographic features, disease characteristics, motor function, vision, and cognition. The most important driving skills and off-road predictors of the pass/fail outcome were identified using multivariate stepwise regression analyses. Eighty-six (65%) passed and 36 (35%) failed the on-road driving evaluation. Persons who failed performed worse on all on-road items. When adjusted for age and gender, poor performances on lateral positioning at low speed, speed adaptations at high speed, and left turning maneuvers yielded the best model that determined the pass/fail decision (R(2) = 0.56). The fail group performed poorer on all motor, visual, and cognitive tests. Measures of visual scanning, motor severity, PD subtype, visual acuity, executive functions, and divided attention were independent predictors of pass/fail decisions in the multivariate model (R(2) = 0.60). Our study demonstrated that failure on a road test in PD is determined by impairments in specific driving skills and associated with deficits in motor, visual, executive, and visuospatial functions. These findings point to specific driving and off-road impairments that can be targeted in multimodal rehabilitation programs for drivers with PD. © 2013 Movement Disorder Society.

Road safety and road traffic accidents in Saudi Arabia

Science.gov (United States)

Mansuri, Farah A.; Al-Zalabani, Abdulmohsen H.; Zalat, Marwa M.; Qabshawi, Reem I.

2015-01-01

Objectives: To identify the changing trends and crucial preventive approaches to road traffic accidents (RTAs) adopted in the Kingdom of Saudi Arabia (KSA) over the last 2.5 decades, and to analyze aspects previously overlooked. Methods: This systematic review was based on evidence of RTAs in KSA. All articles published during the last 25 years on road traffic accident in KSA were analyzed. This study was carried out from December 2013 to May 2014 in the Department of Family and Community Medicine, Taibah University, Al-Madinah Al-Munawwarah, KSA. Results: Road traffic accidents accounted for 83.4% of all trauma admissions in 1984-1989, and no such overall trend was studied thereafter. The most frequently injured body regions as reported in the latest studies were head and neck, followed by upper and lower extremities, which was found to be opposite to that of the studies reported earlier. Hospital data showed an 8% non-significant increase in road accident mortalities in contrast to police records of a 27% significant reduction during the years 2005-2010. Excessive speeding was the most common cause reported in all recent and past studies. Conclusion: Disparity was common in the type of reporting of RTAs, outcome measures, and possible causes over a period of 2.5 decade. All research exclusively looked into the drivers’ faults. A sentinel surveillance of road crashes should be kept in place in the secondary and tertiary care hospitals for all regions of KSA. PMID:25828277

Road traffic noise: self-reported noise annoyance versus GIS modelled road traffic noise exposure.

Science.gov (United States)

Birk, Matthias; Ivina, Olga; von Klot, Stephanie; Babisch, Wolfgang; Heinrich, Joachim

2011-11-01

self-reported road traffic noise annoyance is commonly used in epidemiological studies for assessment of potential health effects. Alternatively, some studies have used geographic information system (GIS) modelled exposure to road traffic noise as an objective parameter. The aim of this study was to analyse the association between noise exposure due to neighbouring road traffic and the noise annoyance of adults, taking other determinants into consideration. parents of 951 Munich children from the two German birth cohorts GINIplus and LISAplus reported their annoyance due to road traffic noise at home. GIS modelled road traffic noise exposure (L(den), maximum within a 50 m buffer) from the noise map of the city of Munich was available for all families. GIS-based calculated distance to the closest major road (≥10,000 vehicles per day) and questionnaire based-information about family income, parental education and the type of the street of residence were explored for their potential influence. An ordered logit regression model was applied. The noise levels (L(den)) and the reported noise annoyance were compared with an established exposure-response function. the correlation between noise annoyance and noise exposure (L(den)) was fair (Spearman correlation r(s) = 0.37). The distance to a major road and the type of street were strong predictors for the noise annoyance. The annoyance modelled by the established exposure-response function and that estimated by the ordered logit model were moderately associated (Pearson's correlation r(p) = 0.50). road traffic noise annoyance was associated with GIS modelled neighbouring road traffic noise exposure (L(den)). The distance to a major road and the type of street were additional explanatory factors of the noise annoyance appraisal.

Geotechnical Monitoring of the Automobile Road

Science.gov (United States)

Matsiy, Vladimir

2017-12-01

In the present article, the results of geotechnical monitoring of A-147 automobile road “Dzhubga-Sochi” are given. Some sections of the automobile road suffered from the landslide adjustment movements; it resulted in many deformations of the retaining structures, the damages of the roadbed and ground crawling over the retaining walls. The observation data made it possible to specify the borders of the active landslide and to form a forecast of the landslide activity in the sections of the automobile roads. Due to monitoring being carried out, there was substantiated the necessity to correct the service forms and records connected with the automobile road reconstruction.

FEATURES ROAD SAFETY AUDIT

Directory of Open Access Journals (Sweden)

L. Abramova

2015-07-01

Full Text Available Development of the road network, increasing motorization of the population significantly increase the risk of accidents. Experts in the field of traffic are developing methods to reduce the probability of accidents. The ways of solving the problems of road safety audit at various stages of the «life» of roads are considered.

Effects of roads on survival of San Clemente Island foxes

Science.gov (United States)

Snow, N.P.; Andelt, William F.; Stanley, T.R.; Resnik, J.R.; Munson, L.

2012-01-01

Roads generate a variety of influences on wildlife populations; however, little is known about the effects of roads on endemic wildlife on islands. Specifically, road-kills of island foxes (Urocyon littoralis) on San Clemente Island (SCI), Channel Islands, California, USA are a concern for resource managers. To determine the effects of roads on island foxes, we radiocollared foxes using a 3-tiered sampling design to represent the entire population in the study area, a sub-population near roads, and a sub-population away from roads on SCI. We examined annual survival rates using nest-survival models, causes of mortalities, and movements for each sample. We found the population had high annual survival (0.90), although survival declined with use of road habitat, particularly for intermediate-aged foxes. Foxes living near roads suffered lower annual survival (0.76), resulting from high frequencies of road-kills (7 of 11 mortalities). Foxes living away from roads had the highest annual survival (0.97). Road-kill was the most prominent cause of mortality detected on SCI, which we estimated as killing 3-8% of the population in the study area annually. Based on movements, we were unable to detect any responses by foxes that minimized their risks from roads. The probabilities of road-kills increased with use of the road habitat, volume of traffic, and decreasing road sinuosity. We recommend that managers should attempt to reduce road-kills by deterring or excluding foxes from entering roads, and attempting to modify behaviors of motorists to be vigilant for foxes. ?? 2011 The Wildlife Society.

Who is in control of road safety? A STAMP control structure analysis of the road transport system in Queensland, Australia.

Science.gov (United States)

Salmon, Paul M; Read, Gemma J M; Stevens, Nicholas J

2016-11-01

Despite significant progress, road trauma continues to represent a global safety issue. In Queensland (Qld), Australia, there is currently a focus on preventing the 'fatal five' behaviours underpinning road trauma (drug and drink driving, distraction, seat belt wearing, speeding, and fatigue), along with an emphasis on a shared responsibility for road safety that spans road users, vehicle manufacturers, designers, policy makers etc. The aim of this article is to clarify who shares the responsibility for road safety in Qld and to determine what control measures are enacted to prevent the fatal five behaviours. This is achieved through the presentation of a control structure model that depicts the actors and organisations within the Qld road transport system along with the control and feedback relationships that exist between them. Validated through a Delphi study, the model shows a diverse set of actors and organisations who share the responsibility for road safety that goes beyond those discussed in road safety policies and strategies. The analysis also shows that, compared to other safety critical domains, there are less formal control structures in road transport and that opportunities exist to add new controls and strengthen existing ones. Relationships that influence rather than control are also prominent. Finally, when compared to other safety critical domains, the strength of road safety controls is brought into question. Copyright © 2016 Elsevier Ltd. All rights reserved.

Development of a sensor platform for roadway mapping : part b - mapping the road fog lines : final report.

Science.gov (United States)

2015-04-01

Our objective is the development and evaluation of a low-cost, vehicle-mounted sensor suite capable of generating : map data with lane and road boundary information accurate to the 10 cm (4 in) level. Such a map could be used for : a number of differ...

Contribution of geophysical methods to the detection of underground cavities in salt series. Development in different projects in Morocco (roads, rail, etc…

Directory of Open Access Journals (Sweden)

Tlemçani M.K.

2018-01-01

Full Text Available As part of the geotechnical studies of a road project, a geophysical investigation by electrical tomography, microgravimetry, and boreholes, was carried out in order to locate if the areas can present or not a risks of ground instability along the road alignment. The road is located near a rock salt mine. This geophysical survey had demonstrated that the area may present major risks for the stability of the road platform. This risk is related to the existence of large expanses of saliferous rocks.The dissolution and exploitation of salt provoked underground voids under the future road. The results of this geophysical survey have allowed the designer office to propose more suitable solutions to solve this problem or even the possibility of shifting another site.

Pavement Subgrade Performance Study in the Danish Road Testing Machine

DEFF Research Database (Denmark)

Ullidtz, Per; Ertman Larsen, Hans Jørgen

1997-01-01

Most existing pavement subgrade criteria are based on the AASHO Road Test, where only one material was tested and for only one climatic condition. To study the validity of these criteria and to refine the criteria a co-operative research program entitled the "International Pavement Subgrade...... Performance Study" was sponsored by the FHWA with American, Finnish and Danish partners. This paper describes the first test series which was carried out in the Danish Road Testing Machine (RTM).The first step in this program is a full scale test on an instrumented pavement in the Danish Road Testing Machine....... Pressure gauges and strain cells were installed in the upper part of the subgrade, for measuring stresses and strains in all three directions. During and after construction FWD testing was carried out to evaluate the elastic parameters of the materials. These parameters were then used with the theory...

Case study: the Argentina Road Safety Project: lessons learned for the decade of action for road safety, 2011-2020.

Science.gov (United States)

Raffo, Veronica; Bliss, Tony; Shotten, Marc; Sleet, David; Blanchard, Claire

2013-12-01

This case study of the Argentina Road Safety Project demonstrates how the application of World Bank road safety project guidelines focused on institution building can accelerate knowledge transfer, scale up investment and improve the focus on results. The case study highlights road safety as a development priority and outlines World Bank initiatives addressing the implementation of the World Report on Road Traffic Injury's recommendations and the subsequent launch of the Decade of Action for Road Safety, from 2011-2020. The case study emphasizes the vital role played by the lead agency in ensuring sustainable road safety improvements and promoting the shift to a 'Safe System' approach, which necessitated the strengthening of all elements of the road safety management system. It summarizes road safety performance and institutional initiatives in Argentina leading up to the preparation and implementation of the project. We describe the project's development objectives, financing arrangements, specific components and investment staging. Finally, we discuss its innovative features and lessons learned, and present a set of supplementary guidelines, both to assist multilateral development banks and their clients with future road safety initiatives, and to encourage better linkages between the health and transportation sectors supporting them.

Gravel roads management : volume 2, gravel roads management : implementation guide.

Science.gov (United States)

2011-10-01

This report establishes procedures for managing dirt and gravel roads, with a primary focus on smaller agencies, such as Wyoming counties, that must manage their roads with very limited resources. The report strives, first, to guide and assist smalle...

Gravel roads management : volume 3, gravel roads management : programming guide.

Science.gov (United States)

2010-10-01

This report establishes procedures for managing dirt and gravel roads, with a primary focus on smaller agencies, such as Wyoming counties, that must manage their roads with very limited resources. The report strives, first, to guide and assist smalle...

VT Road Centerline

Data.gov (United States)

Vermont Center for Geographic Information — (Link to Metadata)(User Guide)(Symbology layer files: aotclass_only.lyr aotclass_surfacetyp.lyr)The Vermont Road Centerline data layer (TransRoad_RDS) contains all...

Erosion and sediment delivery following removal of forest roads

Science.gov (United States)

Madej, Mary Ann

2001-01-01

Erosion control treatments were applied to abandoned logging roads in California, with the goal of reducing road-related sediment input to streams and restoring natural hydrologic patterns on the landscape. Treatment of stream crossings involved excavating culverts and associated road fill and reshaping streambanks. A variety of techniques were applied to road benches, which included decompacting the road surface, placing unstable road fill in more stable locations, and re-establishing natural surface drainage patterns. Following treatment and a 12-year recurrence-interval storm, some road reaches and excavated stream crossings showed evidence of mass movement failures, gullying, bank erosion and channel incision. Post-treatment erosion from excavated stream crossings was related to two variables: a surrogate for stream power (drainage area × channel gradient) and the volume of fill excavated from the channel. Post-treatment erosion on road reaches was related to four explanatory variables: method of treatment, hillslope position (upper, mid-slope or lower), date of treatment, and an interaction term (hillslope position × method of treatment). Sediment delivery from treated roads in upper, middle and lower hillslope positions was 10, 135 and 550 m3 of sediment per kilometre of treated roads, respectively. In contrast, inventories of almost 500 km of forest roads in adjacent catchments indicate that untreated roads produced 1500 to 4700 m3 of sediment per kilometre of road length. Erosion from 300 km of treated roads contributed less than 2 per cent of the total sediment load of Redwood Creek during the period 1978 to 1998. Although road removal treatments do not completely eliminate erosion associated with forest roads, they do substantially reduce sediment yields from abandoned logging roads.

Resource Roads demonstration project : final report

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-15

British Columbia's vast network of resource roads are considered to be amongst the most dangerous, high-risk workplaces in the province. Resource roads, also known as industrial roads, forest service roads, or petroleum development roads, present several unique safety challenges as workplaces. They are built for the purpose of access, egress and transport of materials, resources, equipment and people. However, the lack the same diligence of enforcement and a consistent design, construction, maintenance and standard for use as public highways or municipal roads. There are also safety challenges related to public use of resource roads. This report presented a project, called ResourceRoads by WorkSafe BC that focused on the organization and implementation of a management structure that would provide a system of coordination and a process of compliance for the users of the defined road systems. The project was based on information gathered in two forest districts of Prince George and the South Peace Forest Districts. A committee consisting of the actual owner of the road and other users was formed. The report presented a history of British Columbia's resource road system, and discussed resource roads as industrial workplaces and worksites, as well as resource road fatality statistics. The demonstration project was outlined in terms of project leadership; scope; strategic objectives; project purpose; performance objectives; project communication; demonstration areas; and project stages. Project fundamentals and project findings were also presented along with recommendations and responses to the Auditor General report and the Forest Safety Ombudsman report. It was concluded that potential uses of new technologies for resource road vehicles should be reviewed. tabs., figs.

Road Safety Education in a Science Course: Evaluation of "Science and the Road."

Science.gov (United States)

Gardner, Paul L.

1989-01-01

A traffic safety instructional package--"Science and the Road"--was assessed. It was designed by the Road Traffic Authority of Victoria (Australia) for use in tenth-grade science courses. Evaluation findings resulted in revision of the unit and implementation of more inservice courses for teachers lacking relevant biology and physics…

[Effects of road construction on regional vegetation types].

Science.gov (United States)

Liu, Shi-Liang; Liu, Qi; Wang, Cong; Yang, Jue-Jie; Deng, Li

2013-05-01

As a regional artificial disturbance component, road exerts great effects on vegetation types, and plays a substantial role in defining vegetation distribution to a certain extent. Aiming at the tropical rainforest degradation and artificial forest expansion in Yunnan Province of Southwest China, this paper analyzed the effects of road network extension on regional vegetation types. In the Province, different classes of roads had different effects on the vegetation types, but no obvious regularity was observed in the effects on the patch areas of different vegetation types due to the great variations of road length and affected distance. However, the vegetation patch number was more affected by lower class roads because of their wide distribution. As for different vegetation types, the vegetations on cultivated land were most affected by roads, followed by Castanopsis hystrix and Schima wallichii forests. Road network formation contributed most to the vegetation fragmentation, and there existed significant correlations between the human disturbance factors including village- and road distributions.

CLEAN-ROADS project: air quality considerations after the application of a novel MDSS on winter road maintenance activities

Science.gov (United States)

Pretto, Ilaria; Malloci, Elisa; Tonidandel, Gabriele; Benedetti, Guido; Di Napoli, Claudia; Piazza, Andrea; Apolloni, Roberto; Cavaliere, Roberto

2016-04-01

With this poster we present the environmental benefit on air quality derived by the application of the CLEAN-ROADS pilot project. The CLEAN-ROADS project addresses the problem of the environmental pollution caused by de-icing salts during winter road maintenance activities in the Province of Trento (Italy). A demonstrative Maintenance Decision Support System (MDSS) has been developed in order to improve the intervention procedures of the road management service. Specifically it aims to optimize the efficiency of how available resources (e.g., salt consumption) are currently used while guaranteeing the current level of road safety. The CLEAN-ROADS project has been tested and validated on a test area located in a valley bottom (Adige Valley), where the highest optimization margins are to be expected. The project supports current road maintenance practices, which has proved to be reliable and accurate, with a new scalable and energy-efficient road monitoring system. This system is based on a network of road weather stations (road weather information system, RWIS) installed on the test route. It is capable to collect real-time data about the road conditions and to perform short-term and now-cast road weather forecasts, which actively integrate weather data and bulletins covering the target area [1]. This poster presents the results obtained from a three-year monitoring activity with the aim to (1) determine the impact of de-icing salts on air quality and (2) quantify the improvements obtained by the application of the CLEAN-ROADS project on air quality. The Ambient Air Quality and Cleaner Air for Europe Directive (2008/50/EC) states that contributions to exceedances of particulate matter PM10 limit values that are attributable to road winter salting may be subtracted when assessing compliance with air quality limit values, once provided that reasonable measures have been taken to lower concentrations [2]. As the de-icing salts used in road maintenance are mainly based

The Study of Road Conditions that Affect Tilt-based Text Input for Mobile Devices

Directory of Open Access Journals (Sweden)

Darius Miniotas

2017-07-01

Full Text Available With the rapid advances in technology of mobile devices, their application areas expand continuously as well. Given the growth of the market share for mobile devices, one of the main issues that arise is the need for new and convenient techniques for data input and output suitable for various settings. Tilt-based text input is one of the alternatives that attract attention of current researchers. This study investigates the potential of using tilt-based interaction to enter text while sitting as a passenger in a moving vehicle. In addition, the investigation focused on the characteristics of the road as well as driving conditions that affect tilt-based text input. The study manipulated the following factors: keyboard size 10×4 and road unevenness (small, moderate, and large. 14 participants, aged 25 to 50, took part in the user study. The best performance and the shortest task completion time equal to 24.5 seconds was observed when the vehicle was moving at a constant speed on a straight road with small unevenness. The task completion time increased by 15% in moderate unevenness road and by almost 20 % in large unevenness road. Error rate and movement efficiency were investigated additionally in order to find out the cause of such times.

Value of monitoring in road network management

NARCIS (Netherlands)

Zouch, M.; Courage, W.; Napoles-Morales, O.

2014-01-01

We present a framework for road network management to assist road authorities in maintenance budget estimations and long-term maintenance strategies definition. Information about road conditions is obtained from monitoring. Available data are used to estimate and update prediction of degradation

Road deaths in the Netherlands. [Previously known as: Road fatalities in The Netherlands.

NARCIS (Netherlands)

2011-01-01

This fact sheet outlines the development of the number of road deaths in the Netherlands since 1950. After a rise in the 1950s and 1960s, the number of road deaths in the Netherlands has shown a gradual decline since 1973. In 2016, there were 629 road deaths in the Netherlands. After the years of

Identifying unstable sites on logging roads

Science.gov (United States)

R. M. Rice; J. Lewis

1986-01-01

Logging roads are an important source of forestry-related erosion. The amount of erosion on a forest road is determined by the interaction between how the road is constructed and maintained and the environment in which it is built. The roads in this study were constructed with large bulldozers, and most excavated material was sidecast. The roads studied were...

What is vision Hampton Roads?

Science.gov (United States)

2010-01-01

What is Vision Hampton Roads? : Vision Hampton Roads is... : A regionwide economic development strategy based on the collective strengths of all : localities of Hampton Roads, created with the input of business, academia, nonprofits, : government,...

Functional classification of the Gauteng provincial road network ...

African Journals Online (AJOL)

The built environment consists of various land uses and activities connected by a road network. The efficiency and effectiveness of the road network directly impacts economic growth and societal movement. This study involved the functional classification of the Gauteng provincial road network using the South African Road ...

The smart grid research network: Road map for Smart Grid research, development and demonstration up to 2020

Energy Technology Data Exchange (ETDEWEB)

Troi, A. [Technical Univ. of Denmark. DTU Electrical Engineering, DTU Risoe Campus, Roskilde (Denmark); Noerregaard Joergensen, B. [Syddansk Univ. (SDU), Odense (Denmark); Mahler Larsen, E. [Technical Univ. of Denmark. DTU Electrical Engineering, Kgs. Lyngby (Denmark)] [and others

2013-01-15

This road map is a result of part-recommendation no. 25 in 'MAIN REPORT - The Smart Grid Network's recommendations', written by the Smart Grid Network for the Danish Ministry of Climate, Energy and Building in October 2011. This part-recommendation states: ''Part-recommendation 25 - A road map for Smart Grid research, development and demonstration It is recommended that the electricity sector invite the Ministry to participate in the creation of a road map to ensure that solutions are implemented and coordinated with related policy areas. The sector should also establish a fast-acting working group with representatives from universities, distribution companies and the electric industry, in order to produce a mutual, binding schedule for the RDD of the Smart Grid in Denmark. Time prioritisation of part-recommendation: 2011-2012 Responsibility for implementation of part-recommendation: Universities, along with relevant electric-industry actors, should establish a working group for the completion of a consolidated road map by the end of 2012.'' In its work on this report, the Smart Grid Research Network has focused particularly on part-recommendations 26, 27 and 28 in 'MAIN REPORT - The Smart Grid Network's recommendations', which relate to strengthening and marketing the research infrastructure that will position Denmark as the global hub for Smart Grid development; strengthening basic research into the complex relationships in electric systems with large quantities of independent parties; and improved understanding of consumer behaviour and social economics. Naturally the work has spread to related areas along the way. The work has been conducted by the Smart Grid Research Network. (Author)

Road grip test in Arjeplog

OpenAIRE

Engström, Niclas; Andrén, Henrik; Nybacka, Mikael; Fransson, Lennart; Larsson, Roland

2008-01-01

The Swedish road administration sees a need to improve the road grip estimation capacity for the Swedish road system. The challenge is to find methods to measure road grip fast and reliable. There where six different system types at the tests in Arjeplog, three continuous, two system measuring road grip through deceleration and one system based on GPS and accelerometers. Two system types used air craft runway tires. The other systems used either studded winter tires or friction winter tires. ...

Why Did the Snake Cross the Road? Effects of Roads on Movement and Location of Mates by Garter Snakes (Thamnophis sirtalis parietalis

Directory of Open Access Journals (Sweden)

Richard Shine

2004-06-01

Full Text Available If animals avoid road surfaces or are unable to follow conspecific trails across such surfaces, previously continuous populations may be fragmented. We gathered data on the effects of a small (4-m wide gravel road on the behavior and trail-following abilities of garter snakes (Thamnophis sirtalis parietalis in Manitoba, central Canada. As expected, the road surface had less vegetation cover, a more open canopy and, thus, higher incident radiation than did the surrounding grassland. Contrary to expectations, however, substrate temperatures were lower on the road than in its surrounds, because of the higher reflectivity of the road's surface. On a nearby asphalt road, substrate temperatures were relatively high on the road surface only in the evening, as surrounding areas cooled. Focal sampling showed that snakes avoided the gravel road, typically changing direction when they encountered it. If they crossed the road, they did so by the shortest possible route (straight across. Mate-searching male snakes were less able to follow substrate-deposited pheromonal trails left by females if those trails crossed a road than if the trails were entirely within the surrounding grassland. Thus, roads may significantly modify snake movement patterns, as well as the ability of males to locate reproductive females. Our study provides the first detailed information on the effects of roads on snake behavior.

TRUPACT-I over-the-road test

International Nuclear Information System (INIS)

Glass, R.E.; Gwinn, K.W.

1987-10-01

The TRUPACT-I was subjected to an over-the-road test to determine the package response to normal road environments. This test consisted of six road events: a rough primary road, a railroad grade crossing, an asphalt primary road, a concrete primary road, a bridge approach, and a rough secondary road. The package was instrumented with four vertical accelerometers to determine the package response to road vibration and shock. The results are given in the form of time histories, spectral densities, root mean square, and maximum accelerations for all accelerometers during each event. The results indicated that the railroad grade crossing produced the maximum average vertical accelerations. The maximum accelerations for all events were less than 1 g, and the root mean square loads remained below 0.25 g. 4 refs., 57 figs., 7 tabs

Guidelines for upgrading of low volume roads

CSIR Research Space (South Africa)

Division of Roads

1993-03-01

Full Text Available The purpose of this manual is to provide guidelines on the upgrading of gravel low volume roads to roads and maintenance personnel of road authorities of all sizes. Low volume is, for the purpose of this document, defined to be less than 500...

The scaling structure of the global road network.

Science.gov (United States)

Strano, Emanuele; Giometto, Andrea; Shai, Saray; Bertuzzo, Enrico; Mucha, Peter J; Rinaldo, Andrea

2017-10-01

Because of increasing global urbanization and its immediate consequences, including changes in patterns of food demand, circulation and land use, the next century will witness a major increase in the extent of paved roads built worldwide. To model the effects of this increase, it is crucial to understand whether possible self-organized patterns are inherent in the global road network structure. Here, we use the largest updated database comprising all major roads on the Earth, together with global urban and cropland inventories, to suggest that road length distributions within croplands are indistinguishable from urban ones, once rescaled to account for the difference in mean road length. Such similarity extends to road length distributions within urban or agricultural domains of a given area. We find two distinct regimes for the scaling of the mean road length with the associated area, holding in general at small and at large values of the latter. In suitably large urban and cropland domains, we find that mean and total road lengths increase linearly with their domain area, differently from earlier suggestions. Scaling regimes suggest that simple and universal mechanisms regulate urban and cropland road expansion at the global scale. As such, our findings bear implications for global road infrastructure growth based on land-use change and for planning policies sustaining urban expansions.

Micromorphological investigation on ring road sediments of the Early Bronze Age site Tell Chuera, Syria

Science.gov (United States)

Fritzsch, Dagmar; Thiemeyer, Heinrich

2010-05-01

Tell Chuera is an Early Bronze Age settlement mount in NE-Syria close to the Turkish border. With a diameter of almost 1 km and a height of 18 m it is one of the biggest tells in the region between the rivers Balikh and Khabur. In 1958 the structures of the city wall was known first by Orthmann (1990). This city wall was built of air-dried mud bricks. The age of the founding of this construction is not yet clear. The earliest pottery from the place is dated around 2500 BC to 2350 BC. Inside the fortification a road was detected, which was first excavated by Novak (1995). We took sediment monoliths in 2004 from a new trench, which shows the same situation of the road. A geomagnetic prospection, that included the whole site, suggests that the road was part of the planned extension of the lower town and serves as a circular road (Meyer, in prep.). The micromorphological investigation focussed on the question, how the road was used. Did animals have had access to the town? The thin sections show different indications of the anthropogenic influence. In all samples pseudomorphs after straw are visible. In many parts ash, charred wood fragments, bone fragments, melted material and fragments of basalt and flint were observable, too. These materials are typical for sediments in streets (cf. Goldberg & Macphail, 2006). In some parts of the thin sections faecal spherulites and dung remains with faecal spherulites give an idea that ruminants used the road as well as men. Trampling structures support this assumption. Moreover, leaching of calcite, its redeposition in mottles, pseudomycels and concretions, hydromorphic stains and the translocation of silt indicate postdepositional pedogenic processes. Literature Goldberg, P., & Macphail, R. I. (2006). Practical and theoretical geoarchaeology: UK Blackwell Publishing. Meyer, J.-W. (in prep.). Überlegungen zur Siedlungsstruktur - eine erste Analyse der Ergebnisse der geomagnetischen Prospektion. In J.-W. Meyer (Ed.), Ausgrabungen

EFFECT OF A ROAD SAFETY EDUCATION INTERVENTION ON ROAD SAFETY KNOWLEDGE OF UNIVERSITY DRIVERS IN IBADAN, NIGERIA.

Science.gov (United States)

Olumide, A O; Owoaje, E T

2016-06-01

It is essential for drivers employed in the formal sector to have good knowledge of road safety in order to safeguard their lives and those of the staff they are employed to drive. The study was conducted to determine the effect of a road safety education intervention on road safety knowledge of drivers employed in the University of Ibadan, Nigeria. A quasi-experimental study of 98 intervention and 78 control drivers selected using a cluster sampling technique was conducted. The intervention comprised a two-day training on road safety and first aid. The drivers' knowledge of road safety was measured at baseline, immediately and 4-months post-intervention. Aggregate scores of road safety knowledge were computed giving minimum and maximum obtainable scores of 0 and 16 respectively. Change in mean scores over the three measurement periods was assessed using Repeated Measures Analysis of Variance (ANOVA). Independent t-test was used to compare the scores between intervention and control drivers at each of the assessment periods. Twenty-nine drivers did not complete the study (attrition rate = 16.5%). At baseline, mean road safety knowledge scores for the intervention and control drivers were 12.7±2.2 and 12.9± 2.3 (p = 0.510) respectively. Immediately and four months post intervention, the scores of the intervention drivers were 13.8±1.9 and 12.8±1.6; while scores for the controls were 13.3±2.0 and 13.2±1.8. Repeated measures ANOVA revealed that the increase in knowledge over the three assessment periods was not statistically significant. The intervention resulted in an initial increase in road safety knowledge of the intervention drivers. However, this was not sustained to the forth month post-intervention. This finding suggests periodic refresher trainings to sustain the knowledge acquired.

Planning and Arun's (not so Straight and Narrow Roads

Directory of Open Access Journals (Sweden)

Jeannie van Wyk

2016-04-01

Full Text Available Arun Property Development (Pty Ltd wished to subdivide portions of the farm Langeberg 311, Durbanville. The 1988 structure plan for the area had indicated that certain roads would traverse the property. These and other roads all formed part of a new subdivision known as Sonstraal Heights. As is customary, the ownership of the roads in the subdivision vested in the municipality in terms of section 28 of the Land Use Planning Ordinance 15 of 1985 (C (LUPO on the date of approval of the subdivision. Central to this provision is that no compensation is payable to the developer if the provision of the public roads is based on the normal need therefor arising from the subdivision. Since the developer was of the opinion that the roads it had provided exceeded the normal need, the issue that had to be resolved was whether compensation must be paid for roads beyond what would normally be required for a subdivision. The main issue that the courts, from the Western Cape High Court to the Constitutional Court in Arun Property Development (Pty Ltd v City of Cape Town 2015 2 SA 584 (CC, had to deal with was whether the vesting of roads beyond the normal need therefor arising from the subdivision amounted to an expropriation of land for which compensation is payable in terms of section 25(2 of the Constitution. This case note looks at the different stages of the case, and in the process highlights the historical and legislative background and the subdivision process. It shows that the vesting of the ownership of roads in the municipality is similar to the payment of a development contribution, both of which can be categorised as deprivations of property in terms of the constitutional property clause. On 1 July 2015 LUPO was effectively superseded by the new Spatial Planning and Land Use Management Act 16 of 2013 (SPLUMA and the Western Cape Land Use Planning Act 3 of 2014 (LUPA. Since SPLUMA does not and LUPA does contain a reference to the "normal needs

The safe road transport system approach

Directory of Open Access Journals (Sweden)

Vollpracht Hans-Joachim

2016-07-01

Full Text Available More than 1,24 million people die each year on the worlds roads and between 20 to 50 million suffer from nonfatal injuries. The UN Road Safety Collaboration Meetings under the leadership of WHO developed the Programme for the Decade of Actions for road safety taking nations into the responsibility of improving their accident figures by the five pillars of a national Road Safety Policy, safer Roads, safer Vehicles, safer Road Users and Post Crash Care. It is this Safe System Approach that takes into consideration the land use, infrastructure and transport planning, road user’s abilities and limitations and the close cooperation of all governmental and none governmental stakeholders involved.

A Fuel-Based Assessment of On-Road and Off-Road Mobile Source Emission Trends

Science.gov (United States)

Dallmann, T. R.; Harley, R. A.

2009-12-01

Mobile sources contribute significantly to emissions of nitrogen oxides (NOx) and fine particulate matter (PM2.5) in the United States. These emissions lead to a variety of environmental concerns including adverse human health effects and climate change. In the electric power sector, sulfur dioxide (SO2) and NOx emissions from power plants are measured directly using continuous emission monitoring systems. In contrast for mobile sources, statistical models are used to estimate average emissions from a very large and diverse population of engines. Despite much effort aimed at improving them, mobile source emission inventories continue to have large associated uncertainties. Alternate methods are needed to help evaluate estimates of mobile source emissions and quantify and reduce the associated uncertainties. In this study, a fuel-based approach is used to estimate emissions from mobile sources, including on-road and off-road gasoline and diesel engines. In this approach, engine activity is measured by fuel consumed (in contrast EPA mobile source emission models are based on vehicle km of travel and total amount of engine work output for on-road and off-road engines, respectively). Fuel consumption is defined in this study based on highway fuel tax reports for on-road engines, and from surveys of fuel wholesalers who sell tax-exempt diesel fuel for use in various off-road sectors such as agriculture, construction, and mining. Over the decade-long time period (1996-2006) that is the focus of the present study, national sales of taxable gasoline and diesel fuel intended for on-road use increased by 15 and 43%, respectively. Diesel fuel use by off-road equipment increased by about 20% over the same time period. Growth in fuel consumption offset some of the reductions in pollutant emission factors that occurred during this period. This study relies on in-use measurements of mobile source emission factors, for example from roadside and tunnel studies, remote sensing, and

Louisiana ESI: ROADS (Road Lines)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains the state maintained primary and secondary road network of Louisiana. Vector lines in the data set represent Interstates, U.S. Highways, and...

Contamination of environment in the road surroudings - impact of road salting on Norway spruce (Picea abies) and Scots pine (Pinus sylvestris)

Science.gov (United States)

Hegrová, Jitka; Steiner, Oliver; Goessler, Walter; Tanda, Stefan; Anděl, Petr

2017-09-01

A comprehensive overview of the influence of transport on the environment is presented in this study. The complex analysis of soil and needle samples provides an extensive set of data, which presents elemental contamination of the environment near roads. Traffic pollution (including winter road treatment) has a significant negative influence on our environment. Besides sodium and chlorine from winter maintenance many other elements are emitted into the environment. Three possible sources of contamination are assumed for environmental contamination evaluation: car emission, winter maintenance and abrasion from breaks and clutches. The chemical analysis focused on the description of samples from inorganic point of view. The influence of the contamination potential on the sodium and chlorine content in the samples of 1st year-old and 2nd year-old needles of Norway spruce (Picea abies) and Scots pine (Pinus sylvestris) is discussed. Additional soil samples were taken from each sampling site and analyzed to get insight in the sodium and chlorine distribution. Statistical evaluation was used for interpretation of complex interaction patterns between element concentrations in different aged needles based on localities character including distance from the road and element concentration in soils. This species of needles were chosen because of its heightened sensitivity towards salinization. The study was conducted in different parts of the Czech Republic. The resulting database is a source of valuable information about the influence of transport on the environment.

The Sound of the Road, and other imaginative musings on urban mobility design

DEFF Research Database (Denmark)

Lanng, Ditte Bendix

and possibilities of our mundane transit sites, and ask how we can identify and articulate design potentials for such sites as great sensory and social public spaces. This is what happened in the fall of 2012, when, as part of the course, Theories of the Network City, for students at the urban design master......If you drive at the right speed along the Melody Road of Gunma in Japan, grooves cut into the concrete surface allow you to play the tune “Memories of Summer” with your car and the road as the hybrid instrument. Such a design intervention could occasion us to reconsider the properties...

Wheel-Based Ice Sensors for Road Vehicles

Science.gov (United States)

Arndt, G. Dickey; Fink, Patrick W.; Ngo, Phong H.; Carl, James R.

2011-01-01

Wheel-based sensors for detection of ice on roads and approximate measurement of the thickness of the ice are under development. These sensors could be used to alert drivers to hazardous local icing conditions in real time. In addition, local ice-thickness measurements by these sensors could serve as guidance for the minimum amount of sand and salt required to be dispensed locally onto road surfaces to ensure safety, thereby helping road crews to utilize their total supplies of sand and salt more efficiently. Like some aircraft wing-surface ice sensors described in a number of previous NASA Tech Briefs articles, the wheelbased ice sensors are based, variously, on measurements of changes in capacitance and/or in radio-frequency impedance as affected by ice on surfaces. In the case of ice on road surfaces, the measurable changes in capacitance and/or impedance are attributable to differences among the electric permittivities of air, ice, water, concrete, and soil. In addition, a related phenomenon that can be useful for distinguishing between ice and water is a specific transition in the permittivity of ice at a temperature- dependent frequency. This feature also provides a continuous calibration of the sensor to allow for changing road conditions. Several configurations of wheel-based ice sensors are under consideration. For example, in a simple two-electrode capacitor configuration, one of the electrodes would be a circumferential electrode within a tire, and the ground would be used as the second electrode. Optionally, the steel belts that are already standard parts of many tires could be used as the circumferential electrodes. In another example (see figure), multiple electrodes would be embedded in rubber between the steel belt and the outer tire surface. These electrodes would be excited in alternating polarities at one or more suitable audio or radio frequencies to provide nearly continuous monitoring of the road surface under the tire. In still another

Traffic mortality and the role of minor roads.

Science.gov (United States)

van Langevelde, Frank; van Dooremalen, Coby; Jaarsma, Catharinus F

2009-01-01

Roads have large impacts on wildlife, as they form one of the principal causes of mortality, and disturbance and fragmentation of habitat. These impacts are mainly studied and mitigated on major roads. It is, however, a widespread misconception that most animals are killed on major roads. In this paper, we argue that minor roads have a larger impact on wildlife with respect to habitat destruction, noise load and traffic mortality. We use data on traffic related deaths in badgers (Meles meles) in The Netherlands to illustrate that traffic mortality is higher on minor roads. We ask for a more extensive investigation of the environmental impacts of minor roads. Moreover, we argue that the success of mitigation on roads drastically increases when both major and minor roads are integrated in the planning of traffic flows. Therefore, we propose a strategy based on the concept of a "traffic-calmed area". Traffic-calmed areas create opportunities for wildlife by decreasing limitations for animal movement. We ask for further studies to estimate what size traffic-calmed areas should be to maintain minimum viable animal populations.

5 CFR 930.107 - Waiver of road test.

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Waiver of road test. 930.107 Section 930....107 Waiver of road test. Under the following conditions, OPM or an agency head or his or her designated representative may waive the road test: (a) OPM waives the road test requirement for operators of...

On-Road Chemical Transformation as an Important Mechanism of NO2 Formation

Science.gov (United States)

Nitrogen dioxide (NO2) not only is linked with a number of adverse effects on the respiratory system, but also contributes to the formation of ground-level ozone (O3) and fine particulate matter (PM2.5) pollution. NO2 levels near major roads have been monitored as part of the one...

[The medical social aspects of ambulatory medical care to victims of road traffic accidents].

Science.gov (United States)

Gorbunkov, V Ia; Bugaev, D A; Derevianko, D V

2012-01-01

The article discusses the issues of the organization of medical care to victims of road traffic accidents. The analysis of primary appealability of patients to the first-aid center of Stavropol and Novorossiysk during 2008-2010 is presented. The sampling consisted of 904 cases of this kind of trauma. It is established that among victims of road traffic accident appealed to first-aid centers the pedestrians consist the major part. The traumas of limbs are among the most frequently occurred cases. The victims with cranio-cerebral injuries are among those who appealed most frequently for medical aid. Besides that in most cases (63.4%) the victims with cranio-cerebral injuries were transported not to the neurologic surgery clinic but to the first-aid center This action increased the number of transport stages and duration of time gap before specialized medical care was applied. The conclusion is made concerning the need of further development of out-patient urgent medical care to victims of road traffic accidents.

Quantification of Gravel Rural Road Sediment Production

Science.gov (United States)

Silliman, B. A.; Myers Toman, E.

2014-12-01

Unbound rural roads are thought to be one of the largest anthropogenic sources of sediment reaching stream channels in small watersheds. This sediment deposition can reduce water quality in the streams negatively impacting aquatic habitat as well as impacting municipal drinking water sources. These roads are thought to see an increase in construction and use in southeast Ohio due to the expansion of shale gas development in the region. This study set out to quantify the amount of sediment these rural roads are able to produce. A controlled rain event of 12.7 millimeters of rain over a half hour period was used to drive sediment production over a 0.03 kilometer section of gravel rural road. These 8 segments varied in many characteristics and produced from 2.0 to 8.4 kilograms of sediment per 0.03 kilometers of road with the average production over the 8 segments being 5.5 kilograms of sediment. Sediment production was not strongly correlated with road segment slope but traffic was found to increase sediment production from 1.1 to 3.9 times as much sediment after traffic use. These results will help inform watershed scale sediment budgeting, and inform best management practices for road maintenance and construction. This study also adds to the understanding of the impacts of rural road use and construction associated with the changing land use from agricultural to natural gas extraction.

Road traffic emissions - predictions of future contributions to regional ozone levels in Europe

International Nuclear Information System (INIS)

Reis, S.; Friedrich, R.; Obermeier, A.; Unger, S.

2000-01-01

As part of the European Commission research project 'Assessment of policy instruments for efficient ozone abatement strategies in Europe,' detailed emission projections have been developed for the year 2010 based upon currently adopted measures, and feasible reductions. For road-traffic emissions this projection considers passenger cars, light- and heavy-duty vehicles, mopeds and motorcycles. Here we present model calculations made with the EMEP 3-D Eulerian model to illustrate the relative contribution of each of these road-traffic sectors to ozone concentrations across Europe. The model is run for a six-month period, April-September 1996. The model results clearly suggest that further reduction in road-traffic emissions beyond currently planned measures would be beneficial in reducing ozone over Europe, particularly in the case of heavy-duty vehicles and evaporative emissions. These results do of course depend on the estimated emissions in each sector for the year 2010, and we show that this is a major source of uncertainty in such scenario calculations. (author)

Tools for road infrastructure safety management in poland

Directory of Open Access Journals (Sweden)

Kustra Wojciech

2017-01-01

Full Text Available Road safety can be improved by implementing principles of road safety infrastructure management (RIS on the network of European roads as adopted in the Directive. The document recommends that member states should use tried and tested tools for road safety management such as: road safety impact assessment (RIA, road safety audit (RSA, safety management on existing road networks including road safety ranking (RSM and road safety inspection (RSI. The objective of the methods is to help road authorities to take rational decisions in the area of road safety and road infrastructure safety and understand the consequences occurring in the particular phases of road life cycle. To help with assessing the impact of a road project on the safety of related roads, a method was developed for long-term forecasts of accidents and accident cost estimation as well as a risk classification to identify risks that are not acceptable risks. With regard to road safety audits and road safety inspection, a set of principles was developed to identify risks and the basic classification of mistakes and omissions.

Parameterizing road construction in route-based road weather models: can ground-penetrating radar provide any answers?

International Nuclear Information System (INIS)

Hammond, D S; Chapman, L; Thornes, J E

2011-01-01

A ground-penetrating radar (GPR) survey of a 32 km mixed urban and rural study route is undertaken to assess the usefulness of GPR as a tool for parameterizing road construction in a route-based road weather forecast model. It is shown that GPR can easily identify even the smallest of bridges along the route, which previous thermal mapping surveys have identified as thermal singularities with implications for winter road maintenance. Using individual GPR traces measured at each forecast point along the route, an inflexion point detection algorithm attempts to identify the depth of the uppermost subsurface layers at each forecast point for use in a road weather model instead of existing ordinal road-type classifications. This approach has the potential to allow high resolution modelling of road construction and bridge decks on a scale previously not possible within a road weather model, but initial results reveal that significant future research will be required to unlock the full potential that this technology can bring to the road weather industry. (technical design note)

Road safety audits: The way forward

CSIR Research Space (South Africa)

Labuschagne, FJJ

2010-08-01

Full Text Available The South African Road Safety Manual (SARSM) was published in 1999 and includes guidelines on road safety audits (RSA). The development of SARSM was a proactive process for improving the road environment with respect to road safety but was never...

Estimation of the susceptibility of a road network to shallow landslides with the integration of the sediment connectivity

Directory of Open Access Journals (Sweden)

M. Bordoni

2018-06-01

Full Text Available Landslides cause severe damage to the road network of the hit zone, in terms of both direct (partial or complete destruction of a road or blockages and indirect (traffic restriction or the cut-off of a certain area costs. Thus, the identification of the parts of the road network that are more susceptible to landslides is fundamental to reduce the risk to the population potentially exposed and the financial expense caused by the damage. For these reasons, this paper aimed to develop and test a data-driven model for the identification of road sectors that are susceptible to being hit by shallow landslides triggered in slopes upstream from the infrastructure. This model was based on the Generalized Additive Method, where the function relating predictors and response variable is an empirically fitted smooth function that allows fitting the data in the more likely functional form, considering also non-linear relations. This work also analyzed the importance, on the estimation of the susceptibility, of considering or not the sediment connectivity, which influences the path and the travel distance of the materials mobilized by a slope failure until hitting a potential barrier such as a road. The study was carried out in a catchment of northeastern Oltrepò Pavese (northern Italy, where several shallow landslides affected roads in the last 8 years. The most significant explanatory variables were selected by a random partition of the available dataset in two parts (training and test subsets, 100 times according to a bootstrap procedure. These variables (selected 80 times by the bootstrap procedure were used to build the final susceptibility model, the accuracy of which was estimated through a 100-fold repetition of the holdout method for regression, based on the training and test sets created through the 100 bootstrap model selection. The presented methodology allows the identification, in a robust and reliable way, of the most susceptible road

Evaluation of Shortest Paths in Road Network

Directory of Open Access Journals (Sweden)

Farrukh Shehzad

2009-06-01

Full Text Available Optimization is a key factor in almost all the topics of operations research / management science and economics.The road networks can be optimized within different constraints like time, distance, cost and traffic running onthe roads.This study is based on optimization of real road network by means of distances. Two main objectives arepursued in this research: 1 road distances among different routes are composed in detail; 2 two standardalgorithms (Dijkstra and Floyd-Warshall algoritms are applied to optimize/minimize these distances for bothsingle-source and all-pairs shortest path problems.

The effect of a road safety educational program for kindergarten children on their parents' behavior and knowledge.

Science.gov (United States)

Ben-Bassat, Tamar; Avnieli, Shani

2016-10-01

Road safety education for children is one of the most important means for raising awareness of road safety and for educating children to behave safely as pedestrians, bicycle riders, and vehicle passengers. The current research presents a novel attempt to examine the effect of a unique road safety educational program for kindergarten children on a secondary target group-the parents. The program, named the "Zahav Bagan" program (ZBP), is presented at kindergartens once a week during the entire academic year. It is conducted by senior citizen volunteers and is part of the formal education of the children. The main purpose of the current study was to compare the behavior, awareness, and knowledge about child road safety, of two groups of parents-those whose children participated in the ZBP group, and those whose children did not; this latter group was the control group. A telephone-based survey was conducted using a sample of 76 ZBP parents and 59 control group parents. Results of the survey showed no effect of ZBP on parents' knowledge of child road safety law and recommendations, but more importantly, the results did show a significant effect in terms of parents' observance of safe behavior and in their awareness of road safety in everyday life. These results confirm the importance of educational programs on road safety, especially as triggers and reminders to children and to their parents, to act as cautious road users. Copyright © 2016 Elsevier Ltd. All rights reserved.

The Use of Theatre Tours in Road Safety Education.

Science.gov (United States)

Powney, Janet; And Others

The Scottish Road Safety Campaign and the Road Safety Council of Wales have made a large investment in theater tours as a method of providing road safety education. This study aimed to evaluate the effectiveness of a road safety message delivered by a theater group, Road Safety Officers (RSOs), or, teachers for pupils in upper secondary classes.…

Engineering solutions of traffic safety problems of road transport

Directory of Open Access Journals (Sweden)

M. Bogdevičius

2004-02-01

Full Text Available The authors of this paper focus on the simulation of the motor vehicle movement (taking into consideration motor vehicle dynamics, motor vehicle hydraulic brake system influence on motor vehicle movement, interaction between its wheels with road pavements, road guardrail characteristics, interaction between motor vehicle and road guardrail on a certain road section and propose their specific solution of this problem. The presented results, illustrating the motor vehicle movement trajectories (motor vehicle braking and interaction between motor vehicle and road guardrail at various initial conditions and at various certain pavement surface of the road section under investigation and work of a motor vehicle hydraulic brake system. Taking into consideration the presented general mathematical model and computer aided test results it is possible to investigate various road transport traffic situations as well as to investigate various transport traffic safety problems.

Road geometry as a factor for musculoskeletal injuries due to road traffic accidents in Sub-Himalayan State of Himachal Pradesh

Directory of Open Access Journals (Sweden)

Sunil Kumar Raina

2017-01-01

Full Text Available Background: Road traffic accidents (RTAs kill 1.25 million people each year and injure between 20 and 50 million more people with many incurring a disability as a result of their injury. The road environment (design and geometry can affect driver speed choice, thereby increasing chances of accidents.Materials and Methods: Patients attending tertiary care center for musculoskeletal injuries after an RTA were enrolled in the study. The data were collected using a standard questionnaire. The details on the geometry of the road (type of road; highway or other, metaled or nonmetaled, straight, and curved were obtaine through inspection wherever possible. Results: Majority of the RTAs occurred on state highways (n = 154/313, 49.7% followed by national highways (NH (n = 94/313, 30%. Link roads account for comparatively less number (n = 65/313, 20.7% of cases. Majority of the accidents occurred on metaled road (n = 268, 85.6%; however, the association of different vehicles involved in RTA with the condition of road was not found to be significant statistically (P > 0.5. Further, the majority of the RTA occurred on straight roads (n = 204, 65.1%. Conclusion: Road geometry is an important factor in RTAs as drivers generally tend to choose their speed based on their perception of the appropriate speed for the road geometry.

Assessing impacts of roads: application of a standard assessment protocol

Science.gov (United States)

Duniway, Michael C.; Herrick, Jeffrey E.

2013-01-01

Adaptive management of road networks depends on timely data that accurately reflect the impacts those systems are having on ecosystem processes and associated services. In the absence of reliable data, land managers are left with little more than observations and perceptions to support management decisions of road-associated disturbances. Roads can negatively impact the soil, hydrologic, plant, and animal processes on which virtually all ecosystem services depend. The Interpreting Indicators of Rangeland Health (IIRH) protocol is a qualitative method that has been demonstrated to be effective in characterizing impacts of roads. The goal of this study were to develop, describe, and test an approach for using IIRH to systematically evaluate road impacts across large, diverse arid and semiarid landscapes. We developed a stratified random sampling approach to plot selection based on ecological potential, road inventory data, and image interpretation of road impacts. The test application on a semiarid landscape in southern New Mexico, United States, demonstrates that the approach developed is sensitive to road impacts across a broad range of ecological sites but that not all the types of stratification were useful. Ecological site and road inventory strata accounted for significant variability in the functioning of ecological processes but stratification based on apparent impact did not. Analysis of the repeatability of IIRH applied to road plots indicates that the method is repeatable but consensus evaluations based on multiple observers should be used to minimize risk of bias. Landscape-scale analysis of impacts by roads of contrasting designs (maintained dirt or gravel roads vs. non- or infrequently maintained roads) suggests that future travel management plans for the study area should consider concentrating traffic on fewer roads that are well designed and maintained. Application of the approach by land managers will likely provide important insights into

A combined road weather forecast system to prevent road ice formation in the Adige Valley (Italy)

Science.gov (United States)

Di Napoli, Claudia; Piazza, Andrea; Antonacci, Gianluca; Todeschini, Ilaria; Apolloni, Roberto; Pretto, Ilaria

2016-04-01

Road ice is a dangerous meteorological hazard to a nation's transportation system and economy. By reducing the pavement friction with vehicle tyres, ice formation on pavements increases accident risk and delays travelling times thus posing a serious threat to road users' safety and the running of economic activities. Keeping roads clear and open is therefore essential, especially in mountainous areas where ice is likely to form during the winter period. Winter road maintenance helps to restore road efficiency and security, and its benefits are up to 8 times the costs sustained for anti-icing strategies [1]. However, the optimization of maintenance costs and the reduction of the environmental damage from over-salting demand further improvements. These can be achieved by reliable road weather forecasts, and in particular by the prediction of road surface temperatures (RSTs). RST is one of the most important parameters in determining road surface conditions. It is well known from literature that ice forms on pavements in high-humidity conditions when RSTs are below 0°C. We have therefore implemented an automatic forecast system to predict critical RSTs on a test route along the Adige Valley complex terrain, in the Italian Alps. The system considers two physical models, each computing heat and energy fluxes between the road and the atmosphere. One is Reuter's radiative cooling model, which predicts RSTs at sunrise as a function of surface temperatures at sunset and the time passed since then [2]. One is METRo (Model of the Environment and Temperature of Roads), a road weather forecast software which also considers heat conduction through road material [3]. We have applied the forecast system to a network of road weather stations (road weather information system, RWIS) installed on the test route [4]. Road and atmospheric observations from RWIS have been used as initial conditions for both METRo and Reuter's model. In METRo observations have also been coupled to

30 CFR 816.151 - Primary roads.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Primary roads. 816.151 Section 816.151 Mineral... roads. Primary roads shall meet the requirements of section 816.150 and the additional requirements of this section. (a) Certification. The construction or reconstruction of primary roads shall be certified...

Road Anomalies Detection System Evaluation.

Science.gov (United States)

Silva, Nuno; Shah, Vaibhav; Soares, João; Rodrigues, Helena

2018-06-21

Anomalies on road pavement cause discomfort to drivers and passengers, and may cause mechanical failure or even accidents. Governments spend millions of Euros every year on road maintenance, often causing traffic jams and congestion on urban roads on a daily basis. This paper analyses the difference between the deployment of a road anomalies detection and identification system in a “conditioned” and a real world setup, where the system performed worse compared to the “conditioned” setup. It also presents a system performance analysis based on the analysis of the training data sets; on the analysis of the attributes complexity, through the application of PCA techniques; and on the analysis of the attributes in the context of each anomaly type, using acceleration standard deviation attributes to observe how different anomalies classes are distributed in the Cartesian coordinates system. Overall, in this paper, we describe the main insights on road anomalies detection challenges to support the design and deployment of a new iteration of our system towards the deployment of a road anomaly detection service to provide information about roads condition to drivers and government entities.

Road design, human behaviour, and road accidents : towards a `learning design community'. Paper presented at the international conference `Road safety in Europe', Birmingham, England, September 9-11, 1996.

NARCIS (Netherlands)

Wegman, F.C.M.

1996-01-01

This paper discusses a number of unsolved problems in the field of road design (i.e. geometric design), human behaviour and road safety, particularly concerning the operationalisation of the existing design principles for a safe road network in terms of concrete road design in existing

Detection of the local sliding in the tyre-road contact by measuring vibrations on the inner liner of the tyre

Science.gov (United States)

Niskanen, Arto J.; Tuononen, Ari J.

2017-04-01

Intelligent tyres can provide vital information from the tyre-road contact, especially for autonomous cars and intelligent infrastructure. In this paper, the acceleration measured on the inner liner of a tyre is used to detect the local sliding in the tyre-road contact. The Hilbert-Huang transform is utilized to extract the relevant vibration components and localize them in the wheel rotation angle domain. The energy of the vibration in the trailing part of the contact is shown to increase in low-friction conditions which can be related to the sliding of the tread part as a result of the shear stresses exceeding the local friction limit. To separate the effect of the surface roughness and the friction, different road surfaces were used in the measurements. In addition, the effects of different driving manoeuvres on the measured accelerations and the propagation of the sliding zone in the contact patch during braking are illustrated.

Detection of the local sliding in the tyre-road contact by measuring vibrations on the inner liner of the tyre

International Nuclear Information System (INIS)

Niskanen, Arto J; Tuononen, Ari J

2017-01-01

Intelligent tyres can provide vital information from the tyre-road contact, especially for autonomous cars and intelligent infrastructure. In this paper, the acceleration measured on the inner liner of a tyre is used to detect the local sliding in the tyre-road contact. The Hilbert–Huang transform is utilized to extract the relevant vibration components and localize them in the wheel rotation angle domain. The energy of the vibration in the trailing part of the contact is shown to increase in low-friction conditions which can be related to the sliding of the tread part as a result of the shear stresses exceeding the local friction limit. To separate the effect of the surface roughness and the friction, different road surfaces were used in the measurements. In addition, the effects of different driving manoeuvres on the measured accelerations and the propagation of the sliding zone in the contact patch during braking are illustrated. (paper)

Ranking EU progress on road safety : 11th road safety Performance Index (PIN) report.

NARCIS (Netherlands)

Adminaite, D. Jost, G. Stipdonk, H. & Ward, H.

2017-01-01

In 2010, the European Union renewed its commitment to improve road safety by setting a target of reducing road deaths by 50% by 2020, compared to 2010 levels. This target followed an earlier target set in 2001 to halve road deaths by 2010. Since 2014, progress has virtually ground to a halt. 2016

Road safety policy of the European Union.

NARCIS (Netherlands)

2013-01-01

The European Union (EU) is important for national road safety policies. The EU has several policymaking instruments, such as binding regulations and directives, and non-binding recommendations. An important element in the EU policy plans on road safety are the non-binding European road safety

In–Service Road Safety Audits

Directory of Open Access Journals (Sweden)

A. Mendoza–Díaz

2009-04-01

Full Text Available A road safety audit is a formal analysis that seeks to guarantee that an existing or future road fulfills optimal safety criteria, conducted by a team of experts who se members are independent of the road project. It can be carried out in one, several or all of the stages of the project (planning, design, construction, before opening the road to traffic, and operation. The development and implementation of a road safety audit process is one of the strategies that have been applied in Mexico in recent years to reduce road accidents and their associated consequences. The objective of this work is to present the procedures that have been developed and applied in Mexico, as well as the benefits and problems that have been encountered. The application of those procedures to a specific case is also shown. Emphasis is made in the audit of high ways in the operation stage, which is the type that greater application and development has had in Mexico.

30 CFR 817.151 - Primary roads.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Primary roads. 817.151 Section 817.151 Mineral... roads. Primary roads shall meet the requirements of § 817.150 and the additional requirements of this section. (a) Certification. The construction or reconstruction of primary roads shall be certified in a...

3D GIS BASED EVALUATION OF THE AVAILABLE SIGHT DISTANCE TO ASSESS SAFETY OF URBAN ROADS

Directory of Open Access Journals (Sweden)

M. Bassani

2015-08-01

Full Text Available The available sight distance (ASD in front of the driver to detect possible conflicts with unexpected obstacles is fundamental for traffic safety. In the last 20 years, road design software (RDS has been continuously updated with dedicated modules to estimate ASD, thus assessing the quality of project from a safety point of view. Unfortunately, the evaluation of ASD still represents an issue in the case of existing road, and the object of discussion in the research community. To avoid problems related to the limitation associated with the use of digital terrain models typically employed in RDS, the Geographic Information Systems (GIS software can use digital surface models (DSM which are more flexible in the modelling of sight obstruction due to vegetation, street furniture, and vertical surfaces largely diffused in urbanized areas. The paper deals with the evaluation of GIS in the estimation of ASD in a typical urban road where the density of sight obstruction along the roadside is relatively high. The work explores the case study of a collector road in the city of Turin (Italy. Results confirm the potentiality of GIS software in capturing the complex morphology of the urban environment, thus confirming that GIS could become an important analysis tool for road engineers in the field of road safety. The investigation here described is part of the Pro-VISION Project (funded in 2014 by the Regione Piemonte, Italy.

How long do the dead survive on the road? Carcass persistence probability and implications for road-kill monitoring surveys.

Directory of Open Access Journals (Sweden)

Sara M Santos

Full Text Available BACKGROUND: Road mortality is probably the best-known and visible impact of roads upon wildlife. Although several factors influence road-kill counts, carcass persistence time is considered the most important determinant underlying underestimates of road mortality. The present study aims to describe and model carcass persistence variability on the road for different taxonomic groups under different environmental conditions throughout the year; and also to assess the effect of sampling frequency on the relative variation in road-kill estimates registered within a survey. METHODOLOGY/PRINCIPAL FINDINGS: Daily surveys of road-killed vertebrates were conducted over one year along four road sections with different traffic volumes. Survival analysis was then used to i describe carcass persistence timings for overall and for specific animal groups; ii assess optimal sampling designs according to research objectives; and iii model the influence of road, animal and weather factors on carcass persistence probabilities. Most animal carcasses persisted on the road for the first day only, with some groups disappearing at very high rates. The advisable periodicity of road monitoring that minimizes bias in road mortality estimates is daily monitoring for bats (in the morning and lizards (in the afternoon, daily monitoring for toads, small birds, small mammals, snakes, salamanders, and lagomorphs; 1 day-interval (alternate days for large birds, birds of prey, hedgehogs, and freshwater turtles; and 2 day-interval for carnivores. Multiple factors influenced the persistence probabilities of vertebrate carcasses on the road. Overall, the persistence was much lower for small animals, on roads with lower traffic volumes, for carcasses located on road lanes, and during humid conditions and high temperatures during the wet season and dry seasons, respectively. CONCLUSION/SIGNIFICANCE: The guidance given here on monitoring frequencies is particularly relevant to provide

How long do the dead survive on the road? Carcass persistence probability and implications for road-kill monitoring surveys.

Science.gov (United States)

Santos, Sara M; Carvalho, Filipe; Mira, António

2011-01-01

Road mortality is probably the best-known and visible impact of roads upon wildlife. Although several factors influence road-kill counts, carcass persistence time is considered the most important determinant underlying underestimates of road mortality. The present study aims to describe and model carcass persistence variability on the road for different taxonomic groups under different environmental conditions throughout the year; and also to assess the effect of sampling frequency on the relative variation in road-kill estimates registered within a survey. Daily surveys of road-killed vertebrates were conducted over one year along four road sections with different traffic volumes. Survival analysis was then used to i) describe carcass persistence timings for overall and for specific animal groups; ii) assess optimal sampling designs according to research objectives; and iii) model the influence of road, animal and weather factors on carcass persistence probabilities. Most animal carcasses persisted on the road for the first day only, with some groups disappearing at very high rates. The advisable periodicity of road monitoring that minimizes bias in road mortality estimates is daily monitoring for bats (in the morning) and lizards (in the afternoon), daily monitoring for toads, small birds, small mammals, snakes, salamanders, and lagomorphs; 1 day-interval (alternate days) for large birds, birds of prey, hedgehogs, and freshwater turtles; and 2 day-interval for carnivores. Multiple factors influenced the persistence probabilities of vertebrate carcasses on the road. Overall, the persistence was much lower for small animals, on roads with lower traffic volumes, for carcasses located on road lanes, and during humid conditions and high temperatures during the wet season and dry seasons, respectively. The guidance given here on monitoring frequencies is particularly relevant to provide conservation and transportation agencies with accurate numbers of road

Road weather information for travelers : improving road weather messages and dissemination methods.