Catalytic partial oxidation of methane over porous silica supported VO{sub x} catalysts

Energy Technology Data Exchange (ETDEWEB)

Pirovano, C.; Schoenborn, E.; Kalevaru, V.N.; Wohlrab, S.; Luecke, B.; Martin, A. [University Rostock e.V., Rostock (Germany). Leibniz Inst. for Catalysis

2011-07-01

High surface area mesoporous siliceous MCM-41 and SBA-15 materials have been used as supports to disperse vanadium oxide species using wet impregnation and incipient wetness impregnation methods. These materials were used as catalysts for the partial oxidation of methane (POM) to formaldehyde. The physico-chemical properties of the solids were studied by means of BET, DR-UV/Vis spectroscopy, Py-FTIR and TEM. The influence of support and the preparation method on the dispersion of VOx is also investigated. The catalytic properties of the catalysts were examined in a fixed bed stainless steel reactor at 923 K. So far a maximum production of formaldehyde can be detected on SBA-15 supported VOx-catalysts prepared by incipient wetness impregnation. On this V/SBA-15 material a covalent attachment of catalytic active molecular vanadium species dominates, which in turn leads to a lower activation temperature and thereby reduced over-oxidation. From the best case, the space time yield of HCHO could be reached close to 775 g{sub HCHO} Kg{sub cat}{sup -1} h{sup -1}. (orig.)

Visualizing a Catalyst at Work during the Ignition of the Catalytic Partial Oxidation of Methane

DEFF Research Database (Denmark)

Kimmerle, Bertram; Grunwaldt, Jan-Dierk; Baiker, Alfons

2009-01-01

We present a spatiotemporal operando X-ray absorption study of a highly dynamic process, the ignition of the noble metal catalyzed partial oxidation of methane. Evolvement and propagation of the platinum component's structural changes are investigated with a high-speed X-ray camera, which...... in combination with temperature profiling by IR-thermography and catalytic activity measurements by online mass spectrometry gives insight into the first stages of the ignition of the reaction toward hydrogen and carbon monoxide....

Experimental and numerical investigation of the catalytic partial oxidation of methane to synthesis gas for power generation applications[Dissertation 17183

Energy Technology Data Exchange (ETDEWEB)

Schneider, A.

2007-07-01

The present work addresses the catalytic partial oxidation (CPO) of methane to synthesis gas, with particular emphasis on power generation applications. A combined experimental and numerical investigation of methane partial oxidation to synthesis gas (H{sub 2}, CO) over rhodium-based catalysts has been carried out at pressures of up to 10 bar. The reactivity of the produced hydrogen and the suitably-low light-off temperatures of the CPO reactor, greatly facilitate operation of power generation gas turbines with reduced NO{sub x} emissions, stable operation with low calorific value fuels, and new combustion strategies for efficient CO{sub 2} capture. Those strategies utilize CPO of methane with oxygen (separated from air) and large exhaust gas recycle (H{sub 2}O and CO{sub 2}). An optically accessible catalytic channel-flow reactor was used to carry out Raman spectroscopy of major gas-phase species and laser induced fluorescence (LIF) of formaldehyde, in order to gain fundamental information on the catalytic and gas-phase chemical pathways. Transverse concentration profiles measured by the spontaneous Raman scattering technique determined the catalytic reactivity, while the LIF provided flame shapes and anchoring positions that, in turn, characterized the gaseous reactivity. Comparison between measurements and 2-D CFD computations, led to the validation of detailed catalytic and gas-phase reaction mechanisms. Experiments in a subscale gas-turbine honeycomb catalytic reactor have shown that the foregoing reaction mechanisms were also appropriate under gas-turbine relevant conditions with short reactant residence times. The light-off behavior of the subscale honeycomb reactor was reproduced by transient 2-D CFD computations. Ignition and extinction in CPO was studied. It was shown that, despite the chemical impact of the H{sub 2}O diluent during the transient catalytic ignition event, the light-off times themselves were largely unaffected by the exhaust gas dilution

Fuel processor integrated H{sub 2}S catalytic partial oxidation technology for sulfur removal in fuel cell power plants

Energy Technology Data Exchange (ETDEWEB)

Gardner, T.H.; Berry, D.A.; Lyons, K.D.; Beer, S.K.; Freed, A.D. [U.S. Department of Energy, Morgantown, WV (USA). National Energy Technology Laboratory

2002-12-01

H{sub 2}S catalytic partial oxidation technology with an activated carbon catalyst was found to be a promising method for the removal of hydrogen sulfide from fuel cell hydrocarbon feedstocks. Three different fuel cell feedstocks were considered for analysis: sour natural gas, sour effluent from a liquid middle distillate fuel processor and a Texaco O{sub 2}-blown coal-derived synthesis gas. The H{sub 2}S catalytic partial oxidation reaction, its integratability into fuel cell power plants with different hydrocarbon feedstocks and its salient features are discussed. Experimental results indicate that H{sub 2}S concentration can be removed down to the part-per-million level in these plants. Additionally, a power law rate expression was developed and reaction kinetics compared to prior literature. The activation energy for this reaction was determined to be 34.4 kJ/g mol with the reaction being first order in H{sub 2}S and 0.3 order in O{sub 2}. 18 refs., 14 figs., 3 tabs.

Non-catalytic recuperative reformer

Science.gov (United States)

Khinkis, Mark J.; Kozlov, Aleksandr P.; Kurek, Harry

2015-12-22

A non-catalytic recuperative reformer has a flue gas flow path for conducting hot flue gas from a thermal process and a reforming mixture flow path for conducting a reforming mixture. At least a portion of the reforming mixture flow path is embedded in the flue gas flow path to permit heat transfer from the hot flue gas to the reforming mixture. The reforming mixture flow path contains substantially no material commonly used as a catalyst for reforming hydrocarbon fuel (e.g., nickel oxide, platinum group elements or rhenium), but instead the reforming mixture is reformed into a higher calorific fuel via reactions due to the heat transfer and residence time. In a preferred embodiment, extended surfaces of metal material such as stainless steel or metal alloy that are high in nickel content are included within at least a portion of the reforming mixture flow path.

Redox non-innocent ligands: versatile new tools to control catalytic reactions

NARCIS (Netherlands)

Lyaskovskyy, V.; de Bruin, B.

2012-01-01

In this (tutorial overview) perspective we highlight the use of "redox non-innocent" ligands in catalysis. Two main types of reactivity in which the redox non-innocent ligand is involved can be specified: (A) The redox active ligand participates in the catalytic cycle only by accepting/donating

Partial transpose of random quantum states: Exact formulas and meanders

Energy Technology Data Exchange (ETDEWEB)

Fukuda, Motohisa [Zentrum Mathematik, M5, Technische Universitaet Muenchen, Boltzmannstrasse 3, 85748 Garching (Germany); Sniady, Piotr [Zentrum Mathematik, M5, Technische Universitaet Muenchen, Boltzmannstrasse 3, 85748 Garching (Germany); Institute of Mathematics, Polish Academy of Sciences, ul. Sniadeckich 8, 00-956 Warszawa (Poland); Institute of Mathematics, University of Wroclaw, pl. Grunwaldzki 2/4, 50-384 Wroclaw (Poland)

2013-04-15

We investigate the asymptotic behavior of the empirical eigenvalues distribution of the partial transpose of a random quantum state. The limiting distribution was previously investigated via Wishart random matrices indirectly (by approximating the matrix of trace 1 by the Wishart matrix of random trace) and shown to be the semicircular distribution or the free difference of two free Poisson distributions, depending on how dimensions of the concerned spaces grow. Our use of Wishart matrices gives exact combinatorial formulas for the moments of the partial transpose of the random state. We find three natural asymptotic regimes in terms of geodesics on the permutation groups. Two of them correspond to the above two cases; the third one turns out to be a new matrix model for the meander polynomials. Moreover, we prove the convergence to the semicircular distribution together with its extreme eigenvalues under weaker assumptions, and show large deviation bound for the latter.

Partial transpose of random quantum states: Exact formulas and meanders

Science.gov (United States)

Fukuda, Motohisa; Śniady, Piotr

2013-04-01

We investigate the asymptotic behavior of the empirical eigenvalues distribution of the partial transpose of a random quantum state. The limiting distribution was previously investigated via Wishart random matrices indirectly (by approximating the matrix of trace 1 by the Wishart matrix of random trace) and shown to be the semicircular distribution or the free difference of two free Poisson distributions, depending on how dimensions of the concerned spaces grow. Our use of Wishart matrices gives exact combinatorial formulas for the moments of the partial transpose of the random state. We find three natural asymptotic regimes in terms of geodesics on the permutation groups. Two of them correspond to the above two cases; the third one turns out to be a new matrix model for the meander polynomials. Moreover, we prove the convergence to the semicircular distribution together with its extreme eigenvalues under weaker assumptions, and show large deviation bound for the latter.

Laparoscopic Partial Nephrectomy With Potassium-titanyl-phosphate Laser Versus Conventional Laparoscopic Partial Nephrectomy: An Animal Randomized Controlled Trial

NARCIS (Netherlands)

Rioja, Jorge; Morcillo, Esther; Novalbos, José P.; Sánchez-Hurtado, Miguel A.; Soria, Federico; Pérez-Duarte, Francisco; Díaz-Güemes Martín-Portugüés, Idoia; Laguna, Maria Pilar; Sánchez-Margallo, Francisco Miguel; Rodríguez-Rubio Cortadellas, Federico

2017-01-01

OBJECTIVE To explore the feasibility, safety, and short-term results of potassium-titanyl-phosphate (KTP) laser laparoscopic partial nephrectomy (KTP-LPN) vs conventional laparoscopic partial nephrectomy (C-LPN). MATERIALS AND METHODS Thirty large white female pigs were randomized to KTP-LPN or

Radiant non-catalytic recuperative reformer

Energy Technology Data Exchange (ETDEWEB)

Khinkis, Mark J.; Kozlov, Aleksandr P.

2017-10-31

A radiant, non-catalytic recuperative reformer has a flue gas flow path for conducting hot exhaust gas from a thermal process and a reforming mixture flow path for conducting a reforming mixture. At least a portion of the reforming mixture flow path is positioned adjacent to the flue gas flow path to permit heat transfer from the hot exhaust gas to the reforming mixture. The reforming mixture flow path contains substantially no material commonly used as a catalyst for reforming hydrocarbon fuel (e.g., nickel oxide, platinum group elements or rhenium), but instead the reforming mixture is reformed into a higher calorific fuel via reactions due to the heat transfer and residence time. In a preferred embodiment, a portion of the reforming mixture flow path is positioned outside of flue gas flow path for a relatively large residence time.

Catalytic gasification in fluidized bed, of orange waste. Comparison with non catalytic gasification

International Nuclear Information System (INIS)

Aguiar Trujillo, Leonardo; Marquez Montesinos, Francisco; Ramos Robaina, Boris A.; Guerra Reyes, Yanet; Arauzo Perez, Jesus; Gonzalo Callejo, Alberto; Sanchez Cebrian, Jose L

2011-01-01

The industry processing of the orange, generates high volumes of solid waste. This waste has been used as complement in the animal feeding, in biochemical processes; but their energy use has not been valued by means of the gasification process. They were carried out gasification studies with air in catalytic fluidized bed (using dolomite and olivine as catalysts in a secondary reactor, also varying the temperature of the secondary reactor and the catalyst mass), of the solid waste of orange and the results are compared with those obtained in the gasification with non catalytic air. In the processes we use a design of complete factorial experiment of 2k, valuing the influence of the independent variables and their interactions in the answers, using the software Design-Expert version 7 and a grade of significance of 95 %. The results demonstrate the qualities of the solid waste of orange in the energy use by means of the gasification process for the treatment of these residuals, obtaining a gas of low caloric value. The use of catalysts also diminishes the yield of tars obtained in the gasification process, being more active the dolomite that the olivine in this process. (author)

Universal Partial Words over Non-Binary Alphabets

OpenAIRE

Goeckner, Bennet; Groothuis, Corbin; Hettle, Cyrus; Kell, Brian; Kirkpatrick, Pamela; Kirsch, Rachel; Solava, Ryan

2016-01-01

Chen, Kitaev, M\\"{u}tze, and Sun recently introduced the notion of universal partial words, a generalization of universal words and de Bruijn sequences. Universal partial words allow for a wild-card character $\\diamond$, which is a placeholder for any letter in the alphabet. We settle and strengthen conjectures posed in the same paper where this notion was introduced. For non-binary alphabets, we show that universal partial words have periodic $\\diamond$ structure and are cyclic, and we give ...

An MGF-based unified framework to determine the joint statistics of partial sums of ordered i.n.d. random variables

KAUST Repository

Nam, Sungsik

2014-08-01

The joint statistics of partial sums of ordered random variables (RVs) are often needed for the accurate performance characterization of a wide variety of wireless communication systems. A unified analytical framework to determine the joint statistics of partial sums of ordered independent and identically distributed (i.i.d.) random variables was recently presented. However, the identical distribution assumption may not be valid in several real-world applications. With this motivation in mind, we consider in this paper the more general case in which the random variables are independent but not necessarily identically distributed (i.n.d.). More specifically, we extend the previous analysis and introduce a new more general unified analytical framework to determine the joint statistics of partial sums of ordered i.n.d. RVs. Our mathematical formalism is illustrated with an application on the exact performance analysis of the capture probability of generalized selection combining (GSC)-based RAKE receivers operating over frequency-selective fading channels with a non-uniform power delay profile. © 1991-2012 IEEE.

Partial substitution of manganese with cerium in SrMnO_3 nano-perovskite catalyst. Effect of the modification on the catalytic combustion of dilute acetone

International Nuclear Information System (INIS)

Rezlescu, Nicolae; Rezlescu, Elena; Popa, Paul Dorin; Doroftei, Corneliu; Ignat, Maria

2016-01-01

Ultrafine SrMn_1_−_xCe_xO_3 (x = 0, 02) perovskites were prepared by self-combustion method and heat treatment at 1000 °C for 4 h. The structure and surface properties were investigated by X-ray powder diffraction, scanning electron microscopy (SEM), EDX spectroscopy, and BET analysis. The catalyst properties of the perovskite nanopowders were tested in the catalytic combustion of dilute acetone at atmospheric pressure. The results revealed that the partial substitution of Mn by Ce ions (x = 0.2) in perovskite structure of SrMnO_3 had significantly improved catalytic activity of the perovskite. The SrMn_0_._8Ce_0_,_2O_3 perovskite composition can be a good candidate for catalytic combustion of low concentration acetone (1–2‰ in air) at low temperatures. The acetone conversion over this catalyst exceeds 90% at 200 °C, whereas over SrMnO_3 it is only 50%. Compared with SrMnO_3, T_5_0 is decreased by 75 °C and T_9_0 is decreased by 70 °C. The enhancement of the catalytic activity at a Ce doping of 0.2 may be ascribed to smaller crystallite sizes, larger specific surface area and the presence of Ce and Mn cations with variable valence in the perovskite structure. - Highlights: • A non-conventional method was used to make nanostructured perovskite samples. • XRD study confirms perovskite structure and nanosize of crystallites. • EDX analyses confirm homogeneity and purity of the samples. • The catalytic testing was carried out in the flameless combustion of dilute acetone. • SrMn_0_._8Ce_0_._2O_3 perovskite can be a promising catalyst for acetone combustion at low temperature.

Statistical study of the non-linear propagation of a partially coherent laser beam

International Nuclear Information System (INIS)

Ayanides, J.P.

2001-01-01

This research thesis is related to the LMJ project (Laser MegaJoule) and thus to the study and development of thermonuclear fusion. It reports the study of the propagation of a partially-coherent laser beam by using a statistical modelling in order to obtain mean values for the field, and thus bypassing a complex and costly calculation of deterministic quantities. Random fluctuations of the propagated field are supposed to comply with a Gaussian statistics; the laser central wavelength is supposed to be small with respect with fluctuation magnitude; a scale factor is introduced to clearly distinguish the scale of the random and fast variations of the field fluctuations, and the scale of the slow deterministic variations of the field envelopes. The author reports the study of propagation through a purely linear media and through a non-dispersive media, and then through slow non-dispersive and non-linear media (in which the reaction time is large with respect to grain correlation duration, but small with respect to the variation scale of the field macroscopic envelope), and thirdly through an instantaneous dispersive and non linear media (which instantaneously reacts to the field) [fr

Biochar as porous media for thermally-induced non-catalytic transesterification to synthesize fatty acid ethyl esters from coconut oil

International Nuclear Information System (INIS)

Jung, Jong-Min; Lee, Jechan; Choi, Dongho; Oh, Jeong-Ik; Lee, Sang-Ryong; Kim, Jae-Kon; Kwon, Eilhann E.

2017-01-01

Highlights: • Biodiesel production using renewable resources. • Thermally-induced non-catalytic transesterification. • Synthesis of fatty acid ethyl esters without conventional catalysts. • Using biochar as porous medium in the non-catalytic transesterification. - Abstract: This study put great emphasis on evaluating biochar as porous media for the thermally-induced non-catalytic transesterification reaction to synthesize fatty acid ethyl esters (FAEE) from coconut oil. Thermogravimetric analysis (TGA) of coconut oil experimentally justified that the bond dissociation of fatty acid from the backbone of triglycerides (TGs) could be achieved, which finding could be applied to the non-catalytic transesterification reaction. To use biochar as porous medium, the surficial morphology of maize residue biochar (MRB) was characterized, revealing that biochar possessed the wider pore size distribution ranging from meso- to macro-pores than SiO 2 . The highest yield of FAEE from non-catalytic transesterification of coconut oil in the presence of MRB was 87% at 380 °C. To further enhance the FAEE yield, further studies associated with the production of FAEE with biochar made from different biomasses and various pyrolytic conditions should be performed.

Study of non-catalytic thermal decomposition of triglyceride at hydroprocessing condition

International Nuclear Information System (INIS)

Palanisamy, Shanmugam; Gevert, Borje S.

2016-01-01

Highlights: • Thermolysis of triglycerides occurs above 300 °C and cracking intensify above 350 °C. • Decomposition of carboxylic group observed, and β-H abstraction gives radical. • Product contains aldehyde, ketonic, saturated/unsaturated, cyclic, glycerol group. • Gasoline fraction contains lighter, cyclic and unsaturated hydrocarbons. • Residues contain ester, dimer and carboxylic groups. - Abstract: Non-catalytic thermal decomposition of triglyceride is studied between 300 and 410 °C at 0.1 and 5 MPa in the presence of H 2 or inert gas. This test is carried in tubular reactor filled with inert material (borosilicate glass pellet). The qualitative and analytical results showed that n-alkanes and alkenes with oxygenated olefins were primary products, consistent with thermal cracking to lighter hydrocarbons. The resulting outlet fuel gas obtained mainly from the radical reaction and had high concentration of CO, ethylene and methane. The decomposition forms a large number of radical compounds containing acids, aldehydes, ketones, aliphatic and aromatic hydrocarbon groups. Lighter fraction contains mostly naphthenic group, and heavy fraction contains straight chain paraffinic hydrocarbons. When H 2 partial pressure raised, the cracking of heavy fractions is low, and products contain low concentration of the lighter and gasoline fractions. Here, the thermal decomposition of triglyceride yields lighter fractions due to cracking, decarboxylation and decarbonylation.

Partial substitution of manganese with cerium in SrMnO{sub 3} nano-perovskite catalyst. Effect of the modification on the catalytic combustion of dilute acetone

Energy Technology Data Exchange (ETDEWEB)

Rezlescu, Nicolae, E-mail: nicolae.rezlescu@gmail.com [National Institute of Research and Development for Technical Physics, Iasi (Romania); Rezlescu, Elena; Popa, Paul Dorin; Doroftei, Corneliu [National Institute of Research and Development for Technical Physics, Iasi (Romania); Ignat, Maria [“Al. I. Cuza” University, Faculty of Chemistry, Iasi (Romania)

2016-10-01

Ultrafine SrMn{sub 1−x}Ce{sub x}O{sub 3} (x = 0, 02) perovskites were prepared by self-combustion method and heat treatment at 1000 °C for 4 h. The structure and surface properties were investigated by X-ray powder diffraction, scanning electron microscopy (SEM), EDX spectroscopy, and BET analysis. The catalyst properties of the perovskite nanopowders were tested in the catalytic combustion of dilute acetone at atmospheric pressure. The results revealed that the partial substitution of Mn by Ce ions (x = 0.2) in perovskite structure of SrMnO{sub 3} had significantly improved catalytic activity of the perovskite. The SrMn{sub 0.8}Ce{sub 0,2}O{sub 3} perovskite composition can be a good candidate for catalytic combustion of low concentration acetone (1–2‰ in air) at low temperatures. The acetone conversion over this catalyst exceeds 90% at 200 °C, whereas over SrMnO{sub 3} it is only 50%. Compared with SrMnO{sub 3}, T{sub 50} is decreased by 75 °C and T{sub 90} is decreased by 70 °C. The enhancement of the catalytic activity at a Ce doping of 0.2 may be ascribed to smaller crystallite sizes, larger specific surface area and the presence of Ce and Mn cations with variable valence in the perovskite structure. - Highlights: • A non-conventional method was used to make nanostructured perovskite samples. • XRD study confirms perovskite structure and nanosize of crystallites. • EDX analyses confirm homogeneity and purity of the samples. • The catalytic testing was carried out in the flameless combustion of dilute acetone. • SrMn{sub 0.8}Ce{sub 0.2}O{sub 3} perovskite can be a promising catalyst for acetone combustion at low temperature.

Numerical solution of two-dimensional non-linear partial differential ...

African Journals Online (AJOL)

linear partial differential equations using a hybrid method. The solution technique involves discritizing the non-linear system of partial differential equations (PDEs) to obtain a corresponding nonlinear system of algebraic difference equations to be ...

Theory of potentiostatic current transients for coupled catalytic reaction at random corrugated fractal electrode

International Nuclear Information System (INIS)

Jha, Shailendra K.; Kant, Rama

2010-01-01

We developed a mathematical model for the first order homogeneous catalytic chemical reaction coupled with an electron transfer (EC') on a rough working electrode. Results are obtained for the various roughness models of electrode corrugations, viz., (i) roughness as an exact periodic function, (ii) roughness as a random function with known statistical properties, and (iii) roughness as a random function with statistical self-affine fractality over a finite range of length scales. Method of Green's function is used in the formulation to obtain second-order perturbation (in roughness profile) expressions for the concentration, the local current density and the current transients. A general operator structure between these quantities and arbitrary roughness profile is emphasized. The statistically averaged (randomly rough) electrode response is obtained by an ensemble averaging over all possible surface configurations. An elegant mathematical formula between the average electrochemical current transient and surface structure factor or power-spectrum of roughness is obtained. This formula is used to obtain an explicit equation for the current on an approximately self-affine (or realistic) fractal electrode with a limited range of length scales of irregularities. This description of realistic fractal is obtained by cutoff power law power-spectrum of roughness. The realistic fractal power-spectrum consists of four physical characteristics, viz., the fractal dimension (D H ), lower (l) and upper (L) cutoff length scales of fractality and a proportionality factor (μ), which is related to the topothesy or strength of fractality. Numerical calculations are performed on final results to understand the effect of catalytic reaction and fractal morphological characteristics on potentiostatic current transients.

Catalytic nanoporous membranes

Science.gov (United States)

Pellin, Michael J; Hryn, John N; Elam, Jeffrey W

2013-08-27

A nanoporous catalytic membrane which displays several unique features Including pores which can go through the entire thickness of the membrane. The membrane has a higher catalytic and product selectivity than conventional catalysts. Anodic aluminum oxide (AAO) membranes serve as the catalyst substrate. This substrate is then subjected to Atomic Layer Deposition (ALD), which allows the controlled narrowing of the pores from 40 nm to 10 nm in the substrate by deposition of a preparatory material. Subsequent deposition of a catalytic layer on the inner surfaces of the pores reduces pore sizes to less than 10 nm and allows for a higher degree of reaction selectivity. The small pore sizes allow control over which molecules enter the pores, and the flow-through feature can allow for partial oxidation of reactant species as opposed to complete oxidation. A nanoporous separation membrane, produced by ALD is also provided for use in gaseous and liquid separations. The membrane has a high flow rate of material with 100% selectivity. Also provided is a method for producing a catalytic membrane having flow-through pores and discreet catalytic clusters adhering to the inside surfaces of the pores.

Biodiesel production through non-catalytic supercritical transesterification: current state and perspectives

OpenAIRE

Silva, C. da; Oliveira, J. Vladimir

2014-01-01

The inconveniences of the conventional method for biodiesel production by alkaline catalysis suggests research towards alternative methods, with the non-catalytic transesterification using an alcohol at supercritical conditions proposed as a promising technique for biodiesel production. The so-called supercritical method (SCM) has powerful advantages over conventional techniques, such as fast reaction rates, feedstock flexibility, production efficiency and environmentally friendly benefits. H...

Using a partially randomized patient preference study design to evaluate the therapeutic effect of acupuncture and cupping therapy for fibromyalgia: study protocol for a partially randomized controlled trial.

Science.gov (United States)

Cao, Hui-Juan; Liu, Jian-Ping; Hu, Hui; Wang, Nissi S

2014-07-10

Conducting randomized controlled trials on traditional Chinese non-drug therapies has been limited by factors such as patient preference to specific treatment modality. The aim of this study is to investigate the feasibility of applying a partially randomized patient preference (PRPP) trial model in evaluating the efficacy of two types of traditional Chinese medicine therapies, acupuncture and cupping, for fibromyalgia while accounting for patients' preference of either therapeutic modality. This protocol was approved by the Institutional Ethics Committee of affiliated Dongfang Hospital, Beijing University of Chinese Medicine (approval number: 2013052104-2). One hundred participants with fibromyalgia will be included in this study. Diagnosis of fibromyalgia will be based on the American College of Rheumatology criteria. Before treatment, participants will be interviewed for their preference toward acupuncture or cupping therapy. Fifty participants with no preference will be randomly assigned to one of the two groups and another 50 participants with strong preference to either acupuncture or cupping will receive what they choose. For acupuncture and cupping therapy, the main acupoints used will be tender points (Ashi). Treatment will be three times a week for 5 consecutive weeks with a follow-up period of 12 weeks. Outcome measures will be qualitative (patient expectation and satisfaction) and quantitative (pain intensity, quality of life, depression assessment). NCT01869712 (in clinicaltrials.gov, on 22nd May 2013).

Improved catalytic efficiency, thermophilicity, anti-salt and detergent tolerance of keratinase KerSMD by partially truncation of PPC domain.

Science.gov (United States)

Fang, Zhen; Zhang, Juan; Du, Guocheng; Chen, Jian

2016-06-14

The keratinase from Stenotrophomonas maltophilia (KerSMD) is known for its high activity and pH stability in keratin degradation. However, catalytic efficiency and detergent tolerability need to be improved in order to be used for industrial application. In this work, we obtained several keratinase variants with enhanced catalytic efficiency, thermophilicity, and anti-salt and detergent tolerability by partially truncating the PPC domain of KerSMD. The variants all showed improved catalytic efficiency to synthetic substrate AAPF, with the V355 variant having the highest kcat /Km value of 143.6 s(-1) mM(-1). The truncation of keratinase had little effect on alkaline stability but obviously decreased collagenase activity, developing its potential application in leather treatment. The variants V380, V370, and V355 were thermophilic, with a 1.7-fold enhancement of keratinlytic activity at 60 °C when compared to the wild type. The entire truncation of PPC domain obtained the variant V355 with improved tolerance to alkalinity, salt, chaotropic agents, and detergents. The V355 variant showed more than a 40% improvement in activity under 15% (w/v) NaCl or 4% (w/v) SDS solution, showing excellent stability under harsh washing and unhairing conditions. Our work investigated how protein engineering affects the function of PPC domain of KerSMD.

Non-compact random generalized games and random quasi-variational inequalities

OpenAIRE

Yuan, Xian-Zhi

1994-01-01

In this paper, existence theorems of random maximal elements, random equilibria for the random one-person game and random generalized game with a countable number of players are given as applications of random fixed point theorems. By employing existence theorems of random generalized games, we deduce the existence of solutions for non-compact random quasi-variational inequalities. These in turn are used to establish several existence theorems of noncompact generalized random ...

Convergence of hybrid methods for solving non-linear partial ...

African Journals Online (AJOL)

This paper is concerned with the numerical solution and convergence analysis of non-linear partial differential equations using a hybrid method. The solution technique involves discretizing the non-linear system of PDE to obtain a corresponding non-linear system of algebraic difference equations to be solved at each time ...

Catalytic Conversion of Biofuels

DEFF Research Database (Denmark)

Jørgensen, Betina

This thesis describes the catalytic conversion of bioethanol into higher value chemicals. The motivation has been the unavoidable coming depletion of the fossil resources. The thesis is focused on two ways of utilising ethanol; the steam reforming of ethanol to form hydrogen and the partial oxida...

Hacking on decoy-state quantum key distribution system with partial phase randomization

Science.gov (United States)

Sun, Shi-Hai; Jiang, Mu-Sheng; Ma, Xiang-Chun; Li, Chun-Yan; Liang, Lin-Mei

2014-04-01

Quantum key distribution (QKD) provides means for unconditional secure key transmission between two distant parties. However, in practical implementations, it suffers from quantum hacking due to device imperfections. Here we propose a hybrid measurement attack, with only linear optics, homodyne detection, and single photon detection, to the widely used vacuum + weak decoy state QKD system when the phase of source is partially randomized. Our analysis shows that, in some parameter regimes, the proposed attack would result in an entanglement breaking channel but still be able to trick the legitimate users to believe they have transmitted secure keys. That is, the eavesdropper is able to steal all the key information without discovered by the users. Thus, our proposal reveals that partial phase randomization is not sufficient to guarantee the security of phase-encoding QKD systems with weak coherent states.

Hacking on decoy-state quantum key distribution system with partial phase randomization.

Science.gov (United States)

Sun, Shi-Hai; Jiang, Mu-Sheng; Ma, Xiang-Chun; Li, Chun-Yan; Liang, Lin-Mei

2014-04-23

Quantum key distribution (QKD) provides means for unconditional secure key transmission between two distant parties. However, in practical implementations, it suffers from quantum hacking due to device imperfections. Here we propose a hybrid measurement attack, with only linear optics, homodyne detection, and single photon detection, to the widely used vacuum + weak decoy state QKD system when the phase of source is partially randomized. Our analysis shows that, in some parameter regimes, the proposed attack would result in an entanglement breaking channel but still be able to trick the legitimate users to believe they have transmitted secure keys. That is, the eavesdropper is able to steal all the key information without discovered by the users. Thus, our proposal reveals that partial phase randomization is not sufficient to guarantee the security of phase-encoding QKD systems with weak coherent states.

Reaction phenomena of catalytic partial oxidation of methane under the impact of carbon dioxide addition and heat recirculation

International Nuclear Information System (INIS)

Chen, Wei-Hsin; Lin, Shih-Cheng

2015-01-01

The reaction phenomena of CPOM (catalytic partial oxidation of methane) in a Swiss-roll reactor are studied numerically where a rhodium-based catalyst bed is embedded at the center of the reactor. CO 2 is added into the feed gas and excess enthalpy recovery is performed to evaluate their influences on CPOM performance. In the study, the mole ratio of O 2 to CH 4 (O 2 /CH 4 ratio) is fixed at 0.5 and the mole ratio of CO 2 to O 2 (CO 2 /O 2 ratio) is in the range of 0–2. The results reveal that CO 2 addition into the influent has a slight effect on methane combustion, but significantly enhances dry reforming and suppresses steam reforming. The reaction extents of steam reforming and dry reforming in CPOM without heat recovery and CO 2 addition are in a comparable state. Once CO 2 is added into the feed gas, the dry reforming is enhanced, thereby dominating CH 4 consumption. Compared to the reactor without excess enthalpy recovery, heat recirculation drastically increases the maximum reaction temperature and CH 4 conversion in the catalyst bed; it also intensifies the H 2 selectivity, H 2 yield, CO 2 conversion, and syngas production rate. The predictions indicate that the heat recirculation is able to improve the syngas formation up to 45%. - Highlights: • Catalytic partial oxidation of methane with CO 2 addition and heat recovery is studied. • CO 2 addition has a slight effect on methane combustion. • CO 2 addition significantly enhances dry reforming and suppresses steam reforming. • Dry reforming dominates CH 4 consumption when CO 2 addition is large. • Heat recirculation can improve the syngas formation up to 45%

Does friendship give us non-derivative partial reasons ?

Directory of Open Access Journals (Sweden)

Andrew Reisner

2008-02-01

Full Text Available One way to approach the question of whether there are non-derivative partial reasons of any kind is to give an account of what partial reasons are, and then to consider whether there are such reasons. If there are, then it is at least possible that there are partial reasons of friendship. It is this approach that will be taken here, and it produces several interesting results. The first is a point about the structure of partial reasons. It is at least a necessary condition of a reason’s being partial that it has an explicit relational component. This component, technically, is a relatum in the reason relation that itself is a relation between the person to whom the reason applies and the person whom the action for which there is a reason concerns. The second conclusion of the paper is that this relational component is also required for a number of types of putatively impartial reasons. In order to avoid trivialising the distinction between partial and impartial reasons, some further sufficient condition must be applied. Finally, there is some prospect for a way of distinguishing between impartial reasons that contain a relational component and partial reasons, but that this approach suggests that the question of whether ethics is partial or impartial will be settled at the level of normative ethical discourse, or at least not at the level of discourse about the nature of reasons for action.

Direct observation of doping incorporation pathways in self-catalytic GaMnAs nanowires

Energy Technology Data Exchange (ETDEWEB)

Kasama, T., E-mail: tk@cen.dtu.dk; Yazdi, S. [Center for Electron Nanoscopy, Technical University of Denmark, DK-2800 Kongens Lyngby (Denmark); Thuvander, M. [Department of Applied Physics, Chalmers University of Technology, SE-41296 Gothenburg (Sweden); Siusys, A. [Institute of Physics, Polish Academy of Sciences, al. Lotników 32/46, PL-02-668 Warszawa (Poland); Gontard, L. C. [Instituto de Ciencia de Materiales de Sevilla (CSIC-US), C/Américo Vespucio 49, 41092 Seville (Spain); Kovács, A.; Duchamp, M.; Dunin-Borkowski, R. E. [Ernst Ruska-Centre for Microscopy and Spectroscopy with Electrons and Peter Grünberg Institute, Forschungszentrum Jülich, D-52425 Jülich (Germany); Gustafsson, A. [Solid State Physics and the Nanometer Structure Consortium, Lund University, P.O. Box 118, SE-221 00 Lund (Sweden); Sadowski, J. [Institute of Physics, Polish Academy of Sciences, al. Lotników 32/46, PL-02-668 Warszawa (Poland); MAX-IV Laboratory, Lund University, P.O. Box 118, SE-221 00 Lund (Sweden)

2015-08-07

Doping mechanisms of Mn in GaAs nanowires (NWs) that have been grown self-catalytically at 600 °C by molecular beam epitaxy (MBE) are investigated using advanced electron microscopy techniques and atom probe tomography. Mn is found to be incorporated primarily in the form of non-magnetic tetragonal Ga{sub 0.82}Mn{sub 0.18} nanocrystals in Ga catalyst droplets at the ends of the NWs, while trace amounts of Mn (22 ± 4 at. ppm) are also distributed randomly in the NW bodies without forming clusters or precipitates. The nanocrystals are likely to form after switching off the reaction in the MBE chamber, since they are partially embedded in neck regions of the NWs. The Ga{sub 0.82}Mn{sub 0.18} nanocrystals and the low Mn concentration in the NW bodies are insufficient to induce a ferromagnetic phase transition, suggesting that it is difficult to have high Mn contents in GaAs even in 1-D NW growth via the vapor-liquid-solid process.

Catalytic mechanism of phenylacetone monooxygenases for non-native linear substrates.

Science.gov (United States)

Carvalho, Alexandra T P; Dourado, Daniel F A R; Skvortsov, Timofey; de Abreu, Miguel; Ferguson, Lyndsey J; Quinn, Derek J; Moody, Thomas S; Huang, Meilan

2017-10-11

Phenylacetone monooxygenase (PAMO) is the most stable and thermo-tolerant member of the Baeyer-Villiger monooxygenase family, and therefore it is an ideal candidate for the synthesis of industrially relevant compounds. However, its limited substrate scope has largely limited its industrial applications. In the present work, we provide, for the first time, the catalytic mechanism of PAMO for the native substrate phenylacetone as well as for a linear non-native substrate 2-octanone, using molecular dynamics simulations, quantum mechanics and quantum mechanics/molecular mechanics calculations. We provide a theoretical basis for the preference of the enzyme for the native aromatic substrate over non-native linear substrates. Our study provides fundamental atomic-level insights that can be employed in the rational engineering of PAMO for wide applications in industrial biocatalysis, in particular, in the biotransformation of long-chain aliphatic oils into potential biodiesels.

Random Pattern Vertically Oriented, Partial Thickness Buccinator Myomucosal Flap for Intraoral Reconstruction: A Report of Two Cases

Directory of Open Access Journals (Sweden)

Amin Rahpeyma

2016-05-01

Full Text Available Introduction: Reconstruction of the oral cavity witha flap design containing the buccal mucosa and buccinator muscle but excluding the facial artery and vein is the topic of these case reports. Case Reports: This article uses random pattern vertically oriented partial thickness buccinator myomucosal flap for intraoral reconstruction in two cases. The first was for lining the mandibular anterior vestibule in a trauma patient. The second was for oral side coverage of bone graft in special cleft patient. In both patients, this flap survived and good bone coverage with non-keratinized mucosa was obtained. Conclusion:  Thin long buccal myomucosal flap not including facial artery and vein can survive.

SNCR technology for NO sub x reduction in the cement industry. [Selective non-catalytic reduction

Energy Technology Data Exchange (ETDEWEB)

Kupper, D; Brentrup, L [Krupp Polysius AG, Beckum (Germany)

1992-03-01

This article discusses the selective non-catalytic (SNCR) process for reducing nitrogen oxides in exhaust gases from cement plants. Topics covered include operating experience, injection of additives, selection of the additive, operating costs, reduction efficiency of SNCR, capital expenditure, secondary emissions and cycles of ammonium. (UK).

A non-catalytic N-terminal domain negatively influences the nucleotide exchange activity of translation elongation factor 1Bα.

Science.gov (United States)

Trosiuk, Tetiana V; Shalak, Vyacheslav F; Szczepanowski, Roman H; Negrutskii, Boris S; El'skaya, Anna V

2016-02-01

Eukaryotic translation elongation factor 1Bα (eEF1Bα) is a functional homolog of the bacterial factor EF-Ts, and is a component of the macromolecular eEF1B complex. eEF1Bα functions as a catalyst of guanine nucleotide exchange on translation elongation factor 1A (eEF1A). The C-terminal domain of eEF1Bα is necessary and sufficient for its catalytic activity, whereas the N-terminal domain interacts with eukaryotic translation elongation factor 1Bγ (eEF1Bγ) to form a tight complex. However, eEF1Bγ has been shown to enhance the catalytic activity of eEF1Bα attributed to the C-terminal domain of eEF1Bα. This suggests that the N-terminal domain of eEF1Bα may in some way influence the guanine nucleotide exchange process. We have shown that full-length recombinant eEF1Bα and its truncated forms are non-globular proteins with elongated shapes. Truncation of the N-terminal domain of eEF1Bα, which is dispensable for catalytic activity, resulted in acceleration of the rate of guanine nucleotide exchange on eEF1A compared to full-length eEF1Bα. A similar effect on the catalytic activity of eEF1Bα was observed after its interaction with eEF1Bγ. We suggest that the non-catalytic N-terminal domain of eEF1Bα may interfere with eEF1A binding to the C-terminal catalytic domain, resulting in a decrease in the overall rate of the guanine nucleotide exchange reaction. Formation of a tight complex between the eEF1Bγ and eEF1Bα N-terminal domains abolishes this inhibitory effect. © 2015 FEBS.

The secret life of kinases: insights into non-catalytic signalling functions from pseudokinases.

Science.gov (United States)

Jacobsen, Annette V; Murphy, James M

2017-06-15

Over the past decade, our understanding of the mechanisms by which pseudokinases, which comprise ∼10% of the human and mouse kinomes, mediate signal transduction has advanced rapidly with increasing structural, biochemical, cellular and genetic studies. Pseudokinases are the catalytically defective counterparts of conventional, active protein kinases and have been attributed functions as protein interaction domains acting variously as allosteric modulators of conventional protein kinases and other enzymes, as regulators of protein trafficking or localisation, as hubs to nucleate assembly of signalling complexes, and as transmembrane effectors of such functions. Here, by categorising mammalian pseudokinases based on their known functions, we illustrate the mechanistic diversity among these proteins, which can be viewed as a window into understanding the non-catalytic functions that can be exerted by conventional protein kinases. © 2017 The Author(s); published by Portland Press Limited on behalf of the Biochemical Society.

Catalytic biorefining of plant biomass to non-pyrolytic lignin bio-oil and carbohydrates through hydrogen transfer reactions.

Science.gov (United States)

Ferrini, Paola; Rinaldi, Roberto

2014-08-11

Through catalytic hydrogen transfer reactions, a new biorefining method results in the isolation of depolymerized lignin--a non-pyrolytic lignin bio-oil--in addition to pulps that are amenable to enzymatic hydrolysis. Compared with organosolv lignin, the lignin bio-oil is highly susceptible to further hydrodeoxygenation under low-severity conditions and therefore establishes a unique platform for lignin valorization by heterogeneous catalysis. Overall, the potential of a catalytic biorefining method designed from the perspective of lignin utilization is reported. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Non-universal spreading exponents in a catalytic reaction model

International Nuclear Information System (INIS)

De Andrade, Marcelo F; Figueiredo, W

2011-01-01

We investigated the dependence of the spreading critical exponents and the ultimate survival probability exponent on the initial configuration of a nonequilibrium catalytic reaction model. The model considers the competitive reactions between two different monomers, A and B, where we take into account the energy couplings between nearest neighbor monomers, and the adsorption energies, as well as the temperature T of the catalyst. For each value of T the model shows distinct absorbing states, with different concentrations of the two monomers. Employing an epidemic analysis, we established the behavior of the spreading exponents as we started the Monte Carlo simulations with different concentrations of the monomers. The exponents were determined as a function of the initial concentration ρ A, ini of A monomers. We have also considered initial configurations with correlations for a fixed concentration of A monomers. From the determination of three spreading exponents, and the ultimate survival probability exponent, we checked the validity of the generalized hyperscaling relation for a continuous set of initial states, random and correlated, which are dependent on the temperature of the catalyst

Tantalum oxide-based compounds as new non-noble cathodes for polymer electrolyte fuel cell

International Nuclear Information System (INIS)

Ishihara, Akimitsu; Tamura, Motoko; Matsuzawa, Koichi; Mitsushima, Shigenori; Ota, Ken-ichiro

2010-01-01

Tantalum oxide-based compounds were examined as new non-noble cathodes for polymer electrolyte fuel cell. Tantalum carbonitride powder was partially oxidized under a trace amount of oxygen gas at 900 o C for 4 or 8 h. Onset potential for oxygen reduction reaction (ORR) of the specimen heat-treated for 8 h was 0.94 V vs. reversible hydrogen electrode in 0.1 mol dm -3 sulfuric acid at 30 o C. The partial oxidation of tantalum carboniride was effective to enhance the catalytic activity for the ORR. The partially oxidized specimen with highest catalytic activity had ca. 5.25 eV of ionization potential, indicating that there was most suitable strength of the interaction of oxygen and tantalum on the catalyst surface.

Clinical effectiveness, quality of life and cost-effectiveness of Flaminal® versus Flamazine® in the treatment of partial thickness burns: study protocol for a randomized controlled trial.

Science.gov (United States)

Rashaan, Zjir M; Krijnen, Pieta; van den Akker-van Marle, M Elske; van Baar, Margriet E; Vloemans, Adrianus F P; Dokter, Jan; Tempelman, Fenike R H; van der Vlies, Cees H; Breederveld, Roelf S

2016-03-05

Partial thickness burns are painful, difficult to manage and can have a negative effect on quality of life through scarring, permanent disfigurement and loss of function. The aim of burn treatment in partial thickness burns is to save lives, stimulate wound healing by creating an optimumly moist wound environment, to have debriding and analgesic effects, protect the wound from infection and be convenient for the patient and caregivers. However, there is no consensus on the optimal treatment of partial thickness wounds. Flaminal® and Flamazine® are two standard treatment options that provide the above mentioned properties in burn treatment. Nevertheless, no randomized controlled study has yet compared these two common treatment modalities in partial thickness burns. Thus, the aim of this study is to evaluate the clinical effectiveness, quality of life and cost-effectiveness of Flaminal® versus Flamazine® in the treatment of partial thickness burns. In this two-arm open multi-center randomized controlled trial, 90 patients will be randomized between Flaminal® and Flamazine® and followed for 12 months. The study population will consist of competent or temporarily non-competent (because of sedation and/or intubation) patients, 18 years of age or older, with acute partial thickness burns and a total body surface area (TBSA) of less than 30 %. The main study outcome is time to complete re-epithelialization (greater than 95 %). Secondary outcome measures include need for grafting, wound colonization/infection, number of dressing changes, pain and anxiety, scar formation, health-related quality of life (HRQoL), and costs. This study will contribute to the optimal treatment of patients with partial thickness burn wounds and will provide evidence on the (cost-)effectiveness and quality of life of Flaminal® versus Flamazine® in the treatment of partial thickness burns. Netherlands Trial Register NTR4486 , registered on 2 April 2014.

Microwave-Assisted Coprecipitation Synthesis of LaCoO3 Nanoparticles and Their Catalytic Activity for Syngas Production by Partial Oxidation of Methane

Directory of Open Access Journals (Sweden)

Consuelo Alvarez-Galvan

2018-04-01

Full Text Available LaCoO3 perovskite-type oxides were prepared by microwave-assisted coprecipitation route and investigated in the catalytic partial oxidation of methane (CPOM to syngas. This preparation method aims to achieve higher specific surface areas (ssa than soft-chemical methods commonly used in the preparation of engineered materials. In an attempt to accomplish the creation of mesostructured porous LaCoO3, an ionic template such as cetyl trimethyl ammonium bromide has been used as endotemplate in some samples. The influence of pH and the type of precipitating agent has been studied. The materials have been characterized at different levels: morphology has been studied by scanning electron microscopy, textural properties by nitrogen adsorption–desorption at −196°C, structural analysis by X-ray diffraction, surface composition by X-ray photoelectron spectroscopy, thermal stability by thermogravimetric analysis, and carbon formation in spent catalysts by Raman spectroscopy. Structure-activity correlations point out that the precipitating agent has a key role on the morphology and porosity of the resultant oxide, as well as on the average crystalline domain of lanthanum perovskite (catalyst precursor. Thus, the use of ammonium hydroxide as precipitant leads to materials with a higher surface area and a greater ssa of cobalt (per unit mass, improving their catalytic performance for the CPOM reaction. The best catalytic performance was found for the catalyst prepared using ammonium hydroxide as precipitant (pH 9 and without adding CTAB as endotemplate.

Catalytical Properties of Free and Immobilized Aspergillus niger Tannase

OpenAIRE

Abril Flores-Maltos; Luis V. Rodríguez-Durán; Jacqueline Renovato; Juan C. Contreras; Raúl Rodríguez; Cristóbal N. Aguilar

2011-01-01

A fungal tannase was produced, recovered, and immobilized by entrapment in calcium alginate beads. Catalytical properties of the immobilized enzyme were compared with those of the free one. Tannase was produced intracellularly by the xerophilic fungus Aspergillus niger GH1 in a submerged fermentation system. Enzyme was recovered by cell disruption and the crude extract was partially purified. The catalytical properties of free and immobilized tannase were evaluated using tannic acid and methy...

Topical petrolatum gel alone versus topical silver sulfadiazine with standard gauze dressings for the treatment of superficial partial thickness burns in adults: a randomized controlled trial.

Science.gov (United States)

Genuino, Glenn Angelo S; Baluyut-Angeles, Kathrina Victoria; Espiritu, Andre Paolo T; Lapitan, Marie Carmela M; Buckley, Brian S

2014-11-01

Non-extensive superficial partial thickness burns constitute a major proportion of burns. Conventional treatment involves regular changing of absorptive dressings including the application of a topical antimicrobial, commonly silver sulfadiazine. A systematic review has found insufficient evidence to support or refute such antimicrobial prophylaxis. Another review compared silver sulfadiazine dressings with other occlusive and non-antimicrobial dressings and found insufficient evidence to guide practice. Other research has suggested that dressings with petrolatum gel are as effective as silver sulfadiazine. Single-center, randomized, controlled parallel group trial comparing conventional silver sulfadiazine dressings with treatment with petrolatum gel alone. Consenting adults 18-45 years old with superficial partial thickness burns≤10% total body surface area seen within 24h of the injury were randomized to daily dressing either with petrolatum gel without top dressings or conventional silver sulfadiazine treatment with gauze dressings. Primary outcomes were blinded assessment of time to complete re-epithelialization, wound infection or allergic contact dermatitis. Secondary outcomes included assessment of ease, time and pain of dressing changes. 26 patients were randomized to petrolatum and 24 to silver sulfadiazine dressings. Follow up data available for 19 in each group. Mean time to re-epithelialization was 6.2 days (SD 2.8) in the petrolatum group and 7.8 days (SD 2.1) in the silver sulfadiazine group (p=0.050). No wound infection or dermatitis was observed in either group. Scores for adherence to wound, ease of dressing removal and time required to change dressings were significantly better in the petrolatum treatment arm (ptreatment of minor superficial partial thickness burns in adults. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

Partial safety factor calibration from stochastic finite element computation of welded joint with random geometries

International Nuclear Information System (INIS)

Schoefs, Franck; Chevreuil, Mathilde; Pasqualini, Olivier; Cazuguel, Mikaël

2016-01-01

Welded joints are used in various structures and infrastructures like bridges, ships and offshore structures, and are submitted to cyclic stresses. Their fatigue behaviour is an industrial key issue to deal with and still offers original research subjects. One of the available methods relies on the computing of the stress concentration factor. Even if some studies were previously driven to evaluate this factor onto some cases of welded structures, the shape of the weld joint is generally idealized through a deterministic parametric geometry. Previous experimental works however have shown that this shape plays a key role in the lifetime assessment. We propose in this paper a methodology for computing the stress concentration factor in presence of random geometries of welded joints. In view to make the results available by engineers, this method merges stochastic computation and semi-probabilistic analysis by computing partial safety factors with a dedicated method. - Highlights: • Numerical computation of stress concentration factor with random geometry of weld. • Real data are used for probabilistic modelling. • Identification of partial safety factor from SFEM computation in case of random geometries.

The Relationship Between Structural and Catalytic Activity of α and γ-Bismuth-Molybdate Catalysts for Partial Oxidation of Propylene to Acrolein

Science.gov (United States)

Fansuri, H.; Pham, G. H.; Wibawanta, S.; Zhang, D. K.; French, David

Bismuth-molybdate catalysts are known to be effective for catalytic partial oxidation of propylene to acrolein. Their properties and the kinetics and reaction mechanisms for acrolein production have been extensively studied, especially in their basic forms, such as α, β, and γ-bismuth-molybdate. Although the reaction mechanisms have been reported widely in the literature, a general agreement has not been reached, especially from a catalyst-structure point of view. The present contribution reports an effort to understand the structural changes of α and γ-bismuth-molybdate catalysts at varying temperatures as examined using high temperature XRD and to relate the catalyst performance (activity and selectivity) for propylene partial oxidation to acrolein. The XRD analysis was performed at temperature between 250 and 450°C in ambient atmosphere and the Rietveld refinement method was used to extract unit cell parameters. The results showed a distinct similarity between the shapes of the thermal expansion of the catalysts and their activity and selectivity curves, indicating a significant role that the catalyst interatomic structure plays in the overall reaction mechanism.

Ground-state properties of ordered, partially ordered, and random Cu-Au and Ni-Pt alloys

DEFF Research Database (Denmark)

Ruban, Andrei; Abrikosov, I. A.; Skriver, Hans Lomholt

1995-01-01

We have studied the ground-state properties of ordered, partially ordered, and random Cu-Au and Ni-Pt alloys at the stoichiometric 1/4, 1/2, and 3/4 compositions in the framework of the multisublattice single-site (SS) coherent potential approximation (CPA). Charge-transfer effects in the random ...... for the ordered alloys are in good agreement with experimental data. For all the alloys the calculated ordering energy and the equilibrium lattices parameters are found to be almost exact quadratic functions of the long-range-order parameter....... and the partially ordered alloys are included in the screened impurity model. The prefactor in the Madelung energy is determined by the requirement that the total energy obtained in direct SS CPA calculations should equal the total energy given by the Connolly-Williams expansion based on Green’s function...

Biodiesel production with continuous supercritical process: non-catalytic transesterification and esterification with or without carbon dioxide.

Science.gov (United States)

Tsai, Yu-Ting; Lin, Ho-mu; Lee, Ming-Jer

2013-10-01

The non-catalytic transesterification of refined sunflower oil with supercritical methanol, in the presence of carbon dioxide, was conducted in a tubular reactor at temperatures from 553.2 to 593.2K and pressures up to 25.0 MPa. The FAME yield can be achieved up to about 0.70 at 593.2 K and 10.0 MPa in 23 min with methanol:oil of 25:1 in molar ratio. The effect of adding CO2 on the FAME yield is insignificant. The kinetic behavior of the non-catalytic esterification and transesterification of oleic acid or waste cooking oil (WCO) with supercritical methanol was also investigated. By using the supercritical process, the presence of free fatty acid (FFA) in WCO gives positive contribution to FAME production. The FAME yield of 0.90 from WCO can be achieved in 13 min at 573.2K. The kinetic data of supercritical transesterification and esterifaication were correlated well with a power-law model. Copyright © 2012 Elsevier Ltd. All rights reserved.

A Stochastic Collocation Method for Elliptic Partial Differential Equations with Random Input Data

KAUST Repository

Babuška, Ivo; Nobile, Fabio; Tempone, Raul

2010-01-01

This work proposes and analyzes a stochastic collocation method for solving elliptic partial differential equations with random coefficients and forcing terms. These input data are assumed to depend on a finite number of random variables. The method consists of a Galerkin approximation in space and a collocation in the zeros of suitable tensor product orthogonal polynomials (Gauss points) in the probability space, and naturally leads to the solution of uncoupled deterministic problems as in the Monte Carlo approach. It treats easily a wide range of situations, such as input data that depend nonlinearly on the random variables, diffusivity coefficients with unbounded second moments, and random variables that are correlated or even unbounded. We provide a rigorous convergence analysis and demonstrate exponential convergence of the “probability error” with respect to the number of Gauss points in each direction of the probability space, under some regularity assumptions on the random input data. Numerical examples show the effectiveness of the method. Finally, we include a section with developments posterior to the original publication of this work. There we review sparse grid stochastic collocation methods, which are effective collocation strategies for problems that depend on a moderately large number of random variables.

[Partial splenectomy in sickle cell disease].

Science.gov (United States)

Gutiérrez Díaz, A I; Svarch, E; Arencibia Núñez, A; Sabournin Ferrier, V; Machín García, S; Menendez Veitía, A; Ramón Rodriguez, L; Serrano Mirabal, J; García Peralta, T; López Martin, L G

2015-04-01

Total splenectomy in sickle cell disease is related to a high risk of fulminant sepsis and increased incidence of other events, which have not been reported in patients with partial splenectomy. In this study we examined the patients with sickle cell disease and partial splenectomy and compared the clinical and laboratory results with non-splenectomized patients. We studied 54 patients with sickle cell disease who underwent partial splenectomy in childhood from 1986 until 2011 at the Institute of Hematology and Immunology. They were compared with 54 non-splenectomized patients selected by random sampling with similar characteristics. Partial splenectomy was performed at a mean age of 4.1 years, with a higher frequency in homozygous hemoglobin S (70.4%), and the most common cause was recurrent splenic sequestration crisis. The most common postoperative complications were fever of unknown origin (14.8%) and acute chest syndrome (11.1%). After splenectomy there was a significant increase in leukocytes, neutrophils, and platelets, the latter two parameters remained significantly elevated when compared with non-splenectomized patients. There was no difference in the incidence of clinical events, except hepatic sequestration, which was more common in splenectomized patients. Partial splenectomy was a safe procedure in patients with sickle cell disease. There were no differences in the clinical picture in children splenectomized and non-splenectomized except the greater frequency of hepatic sequestration crisis in the first group. Copyright © 2013 Asociación Española de Pediatría. Published by Elsevier España, S.L.U. All rights reserved.

Oscillatory Behavior during the Catalytic Partial Oxidation of Methane: Following Dynamic Structural Changes of Palladium Using the QEXAFS Technique

DEFF Research Database (Denmark)

Stoetzel, Jan; Frahm, Ronald; Kimmerle, Bertram

2012-01-01

oxidation of methane, the catalyst reduced from the end to the beginning of the catalyst bed and oxidized again toward the end as soon as the entire catalyst bed was reduced. On an entirely oxidized catalyst bed, only total oxidation of methane was observed and consumed the oxygen until the conditions...... of the Pd particles at increasing age of the catalyst was observed, which leads to a lower oscillation frequency. Effects of particle size, oven temperature, and oxygen/methane ratio on the oscillation behavior were studied in detail. The deactivation period (reoxidation of Pd) was much less influenced...... by the oven temperature than the ignition behavior of the catalytic partial oxidation of methane. This indicates that deactivation is caused by an autoreduction of the palladium at the beginning of the catalyst bed due to the high temperature achieved by total oxidation of methane....

Removal of nitrogen compounds from gasification gas by selective catalytic or non-catalytic oxidation; Typpiyhdisteiden poisto kaasutuskaasusta selektiivisellae katalyyttisellae ja ei-katalyyttisellae hapetuksella

Energy Technology Data Exchange (ETDEWEB)

Leppaelahti, J.; Koljonen, T. [VTT Energy, Espoo (Finland)

1996-12-01

In gasification reactive nitrogenous compounds are formed from fuel nitrogen, which may form nitrogen oxides in gas combustion. In fluidized bed gasification the most important nitrogenous compound is ammonia (NH{sub 3}). If ammonia could be decomposed to N{sub 2} already before combustion, the emissions if nitrogen oxides could be reduced significantly. One way of increasing the decomposition rate of NH{sub 3} could be the addition of suitable reactants to the gas, which would react with NH{sub 3} and produce N{sub 2}. The aim of this research is to create basic information, which can be used to develop a new method for removal of nitrogen compounds from gasification gas. The reactions of nitrogen compounds and added reactants are studied in reductive atmosphere in order to find conditions, in which nitrogen compounds can be oxidized selectively to N{sub 2}. The project consists of following subtasks: (1) Selective non-catalytic oxidation (SNCO): Reactions of nitrogen compounds and oxidizers in the gas phase, (2) Selective catalytic oxidation (SCO): Reactions of nitrogen compounds and oxidizers on catalytically active surfaces, (3) Kinetic modelling of experimental results in co-operation with the Combustion Chemistry Research Group of Aabo Akademi University. The most important finding has been that NH{sub 3} can be made to react selectively with the oxidizers even in the presence of large amounts of CO and H{sub 2}. Aluminium oxides were found to be the most effective materials promoting selectivity. (author)

Random catalytic reaction networks

Science.gov (United States)

Stadler, Peter F.; Fontana, Walter; Miller, John H.

1993-03-01

We study networks that are a generalization of replicator (or Lotka-Volterra) equations. They model the dynamics of a population of object types whose binary interactions determine the specific type of interaction product. Such a system always reduces its dimension to a subset that contains production pathways for all of its members. The network equation can be rewritten at a level of collectives in terms of two basic interaction patterns: replicator sets and cyclic transformation pathways among sets. Although the system contains well-known cases that exhibit very complicated dynamics, the generic behavior of randomly generated systems is found (numerically) to be extremely robust: convergence to a globally stable rest point. It is easy to tailor networks that display replicator interactions where the replicators are entire self-sustaining subsystems, rather than structureless units. A numerical scan of random systems highlights the special properties of elementary replicators: they reduce the effective interconnectedness of the system, resulting in enhanced competition, and strong correlations between the concentrations.

Effect of Amifostine on Response Rates in Locally Advanced Non-Small-Cell Lung Cancer Patients Treated on Randomized Controlled Trials: A Meta-Analysis

International Nuclear Information System (INIS)

Mell, Loren K.; Malik, Renuka; Komaki, Ritsuko; Movsas, Benjamin; Swann, R. Suzanne; Langer, Corey; Antonadou, Dosia; Koukourakis, Michael; Mundt, Arno J.

2007-01-01

Purpose: Amifostine can reduce the cytotoxic effects of chemotherapy and radiotherapy in patients with locally advanced non-small-cell lung cancer, but concerns remain regarding its possible tumor-protective effects. Studies with sufficient statistical power to address this question are lacking. Methods and Materials: We performed a meta-analysis of all published clinical trials involving locally advanced non-small-cell lung cancer patients treated with radiotherapy with or without chemotherapy, who had been randomized to treatment with amifostine vs. no amifostine or placebo. Random effects estimates of the relative risk of overall, partial, and complete response were obtained. Results: Seven randomized trials involving 601 patients were identified. Response rate data were available for six studies (552 patients). The pooled relative risk (RR) estimate was 1.07 (95% confidence interval, 0.97-1.18; p = 0.18), 1.21 (95% confidence interval, 0.83-1.78; p = 0.33), and 0.99 (95% confidence interval, 0.78-1.26; p = 0.95) for overall, complete, and partial response, respectively (a RR >1 indicates improvement in response with amifostine compared with the control arm). The results were similar after sensitivity analyses. No evidence was found of treatment effect heterogeneity across the studies. Conclusions: Amifostine has no effect on tumor response in patients with locally advanced non-small-cell lung cancer treated with radiotherapy with or without chemotherapy

Processivity and Subcellular Localization of Glycogen Synthase Depend on a Non-catalytic High Affinity Glycogen-binding Site*

OpenAIRE

Díaz, Adelaida; Martínez-Pons, Carlos; Fita, Ignacio; Ferrer, Juan C.; Guinovart, Joan J.

2011-01-01

Glycogen synthase, a central enzyme in glucose metabolism, catalyzes the successive addition of α-1,4-linked glucose residues to the non-reducing end of a growing glycogen molecule. A non-catalytic glycogen-binding site, identified by x-ray crystallography on the surface of the glycogen synthase from the archaeon Pyrococcus abyssi, has been found to be functionally conserved in the eukaryotic enzymes. The disruption of this binding site in both the archaeal and the human muscle glycogen synth...

Reactivity of organic compounds in catalytic synthesis

Energy Technology Data Exchange (ETDEWEB)

Minachev, Kh M; Bragin, O V

1978-01-01

A comprehensive review of 1976 Soviet research on catalysis delivered to the 1977 annual session of the USSR Academy of Science Council on Catalysis (Baku 6/16-20/77) covers hydrocarbon reactions, including hydrogenation and hydrogenolysis, dehydrogenation, olefin dimerization and disproportionation, and cyclization and dehydrocyclization (e.g., piperylene cyclization and ethylene cyclotrimerization); catalytic and physicochemical properties of zeolites, including cracking, dehydrogenation, and hydroisomerization catalytic syntheses and conversion of heterocyclic and functional hydrocarbon derivatives, including partial and total oxidation (e.g., of o-xylene to phthalic anhydride); syntheses of thiophenes from alkanes and hydrogen sulfide over certain dehydrogenation catalysts; catalytic syntheses involving carbon oxides ( e.g., the development of a new heterogeneous catalyst for hydroformylation of olefins), and of Co-MgO zeolitic catalysts for synthesis of aliphatic hydrocarbons from carbon dioxide and hydrogen, and fabrication of high-viscosity lubricating oils over bifunctional aluminosilicate catalysts.

Magnetic field line random walk in non-axisymmetric turbulence

International Nuclear Information System (INIS)

Tautz, R.C.; Lerche, I.

2011-01-01

Including a random component of a magnetic field parallel to an ambient field introduces a mean perpendicular motion to the average field line. This effect is normally not discussed because one customarily chooses at the outset to ignore such a field component in discussing random walk and diffusion of field lines. A discussion of the basic effect is given, indicating that any random magnetic field with a non-zero helicity will lead to such a non-zero perpendicular mean motion. Several exact analytic illustrations are given of the effect as well as a simple numerical illustration. -- Highlights: → For magnetic field line random walk all magnetic field components are important. → Non-vanishing magnetic helicity leads to mean perpendicular motion. → Analytically exact stream functions illustrate that the novel transverse effect exists.

Advances in solid-catalytic and non-catalytic technologies for biodiesel production

International Nuclear Information System (INIS)

Islam, Aminul; Taufiq-Yap, Yun Hin; Chan, Eng-Seng; Moniruzzaman, M.; Islam, Saiful; Nabi, Md. Nurun

2014-01-01

Highlights: • The recent technologies for promoting biodiesel synthesis were elucidated. • The design of catalyst consideration of biodiesel production was proposed. • The recent advances and remaining difficulties in biodiesel synthesis were outlined. • The future research trend in biodiesel synthesis was highlighted. - Abstract: The insecure supply of fossil fuel coerces the scientific society to keep a vision to boost investments in the renewable energy sector. Among the many renewable fuels currently available around the world, biodiesel offers an immediate impact in our energy. In fact, a huge interest in related research indicates a promising future for the biodiesel technology. Heterogeneous catalyzed production of biodiesel has emerged as a preferred route as it is environmentally benign needs no water washing and product separation is much easier. The number of well-defined catalyst complexes that are able to catalyze transesterification reactions efficiently has been significantly expanded in recent years. The activity of catalysts, specifically in application to solid acid/base catalyst in transesterification reaction depends on their structure, strength of basicity/acidity, surface area as well as the stability of catalyst. There are various process intensification technologies based on the use of alternate energy sources such as ultrasound and microwave. The latest advances in research and development related to biodiesel production is represented by non-catalytic supercritical method and focussed exclusively on these processes as forthcoming transesterification processes. The latest developments in this field featuring highly active catalyst complexes are outlined in this review. The knowledge of more extensive research on advances in biofuels will allow a deeper insight into the mechanism of these technologies toward meeting the critical energy challenges in future

The current status and perspectives of biofuel production via catalytic cracking of edible and non-edible oils

International Nuclear Information System (INIS)

Ong, Yee Kang; Bhatia, Subhash

2010-01-01

Biofuel development has gained the attention of researchers in recent years owing to the rate of depletion of fossil fuels. Several processes are currently employed in the conventional production of different biofuels: the production of biodiesel is catalytically performed either through the transesterification of triglycerides using alcohol or the deoxygenative ecofining of triglycerides in a non-alcohol environment; bio-oil is produced by the pyrolysis of biomass; bio-ethanol is produced by the fermentation of sugars obtained from starch or cellulosic based biomass, while bio-gasoline is produced from the catalytic cracking of triglycerides. Owing to the enormous dependency of transport vehicles running on gasoline engines, the development of bio-gasoline may well reduced the dependence of the fuel market on fossil fuels. The present article summarizes recent progresses and future prospects of biofuel production via catalytic cracking technology. This technology can be implemented in current petroleum refineries with minor modifications. However, reactor design and catalyst choice are important issues and have to be addressed before successful implementation of this technology in commercial ventures.

Determination of organic bases in non-aqueous solvents by catalytic thermometric titration.

Science.gov (United States)

Vajgand, V J; Kiss, T A; Gaál, F F; Zsigrai, I J

1968-07-01

Catalytic thermometric titrations have been developed for bases (brucine, diethylaniline, potassium acetate and triethylamine) in acetic acid by continuous and discontinuous addition of the standard solution and automatic temperature recording. The determination of weak bases, e.g., antipyrine, unsuccessful in acetic acid by catalytic thermometric titration, has been achieved by using nitromethane or acetic anhydride as solvent. Catalytic thermometric titrations were also performed by coulometric generation of hydrogen ions for the determination of micro amounts of weak bases in a mixture of acetic anhyride and acetic acid.

Reduced Mortality With Partial-Breast Irradiation for Early Breast Cancer: A Meta-Analysis of Randomized Trials

International Nuclear Information System (INIS)

Vaidya, Jayant S.; Bulsara, Max; Wenz, Frederik; Coombs, Nathan; Singer, Julian; Ebbs, Stephen; Massarut, Samuele; Saunders, Christobel; Douek, Michael; Williams, Norman R.; Joseph, David; Tobias, Jeffrey S.; Baum, Michael

2016-01-01

Purpose: With earlier detection and more effective treatment, mortality from breast cancer continues to fall and it has become increasingly important to reduce the toxicity of treatments. Partial-breast radiation therapy, which focuses radiation to the tumor bed, may achieve this aim. We analyzed mortality differences in randomized trials of partial-breast irradiation (PBI). Methods and Materials: We included data from published randomized trials of PBI (alone or as part of a risk-adapted approach) versus whole-breast irradiation (WBI) for invasive breast cancer suitable for breast-conserving therapy. We identified trials using PubMed and Google searches with the terms “partial breast irradiation” OR “intraoperative radiotherapy” OR “IMRT” OR (“accelerated” AND “radiation”) AND “randomised/randomized,” as well as through discussion with colleagues in the field. We calculated the proportion of patients who had events in each randomized arm at 5 years' follow-up and created a forest plot using Stata, version 14.1. Results: We identified 9 randomized trials of PBI versus WBI in invasive breast cancer; 5-year outcomes were available for non–breast cancer mortality in 5 trials (n=4489) and for breast cancer mortality in 4 trials (n=4231). The overall mortality was 4.9%. There was no detectable heterogeneity between the trials for any of the outcomes. There was no difference in the proportion of patients dying of breast cancer (difference, 0.000% [95% confidence interval (CI), −0.7 to +0.7]; P=.999). Non–breast cancer mortality with PBI was lower than with WBI (difference, 1.1% [95% CI, −2.1% to −0.2%]; P=.023). Total mortality with PBI was also lower than with WBI (difference, 1.3% [95% CI, −2.5% to 0.0%]; P=.05). Conclusions: Use of PBI instead of WBI in selected patients results in a lower 5-year non–breast cancer and overall mortality, amounting to a 25% reduction in relative terms. This information should be included when

Reduced Mortality With Partial-Breast Irradiation for Early Breast Cancer: A Meta-Analysis of Randomized Trials

Energy Technology Data Exchange (ETDEWEB)

Vaidya, Jayant S., E-mail: jayant.vaidya@ucl.ac.uk [Division of Surgery and Interventional Science, University College London, London (United Kingdom); Department of Surgery, Royal Free Hospital, London (United Kingdom); Department of Surgery, Whittington Health, London (United Kingdom); Bulsara, Max [Department of Biostatistics, University of Notre Dame, Fremantle, WA (Australia); Wenz, Frederik [Department of Radiation Oncology, University Medical Centre Mannheim, University of Heidelberg, Mannheim (Germany); Coombs, Nathan [Department of Surgery, Great Western Hospital, Swindon (United Kingdom); Singer, Julian [Department of Clinical Oncology, The Princess Alexandra Hospital, Harlow (United Kingdom); Ebbs, Stephen [Croydon University Hospital, Croydon (United Kingdom); Massarut, Samuele [National Cancer Institute, Centro di Riferimento Oncologico, Aviano (Italy); Saunders, Christobel [School of Surgery, University of Western Australia, Perth, WA (Australia); Douek, Michael [Department of Surgery, Kings College London, London (United Kingdom); Williams, Norman R. [Division of Surgery and Interventional Science, University College London, London (United Kingdom); Joseph, David [Departments of Radiation Oncology, and Surgery, Sir Charles Gairdner Hospital, Perth, WA (Australia); Tobias, Jeffrey S. [Department of Clinical Oncology, University College London Hospitals, London (United Kingdom); Baum, Michael [Division of Surgery and Interventional Science, University College London, London (United Kingdom)

2016-10-01

Purpose: With earlier detection and more effective treatment, mortality from breast cancer continues to fall and it has become increasingly important to reduce the toxicity of treatments. Partial-breast radiation therapy, which focuses radiation to the tumor bed, may achieve this aim. We analyzed mortality differences in randomized trials of partial-breast irradiation (PBI). Methods and Materials: We included data from published randomized trials of PBI (alone or as part of a risk-adapted approach) versus whole-breast irradiation (WBI) for invasive breast cancer suitable for breast-conserving therapy. We identified trials using PubMed and Google searches with the terms “partial breast irradiation” OR “intraoperative radiotherapy” OR “IMRT” OR (“accelerated” AND “radiation”) AND “randomised/randomized,” as well as through discussion with colleagues in the field. We calculated the proportion of patients who had events in each randomized arm at 5 years' follow-up and created a forest plot using Stata, version 14.1. Results: We identified 9 randomized trials of PBI versus WBI in invasive breast cancer; 5-year outcomes were available for non–breast cancer mortality in 5 trials (n=4489) and for breast cancer mortality in 4 trials (n=4231). The overall mortality was 4.9%. There was no detectable heterogeneity between the trials for any of the outcomes. There was no difference in the proportion of patients dying of breast cancer (difference, 0.000% [95% confidence interval (CI), −0.7 to +0.7]; P=.999). Non–breast cancer mortality with PBI was lower than with WBI (difference, 1.1% [95% CI, −2.1% to −0.2%]; P=.023). Total mortality with PBI was also lower than with WBI (difference, 1.3% [95% CI, −2.5% to 0.0%]; P=.05). Conclusions: Use of PBI instead of WBI in selected patients results in a lower 5-year non–breast cancer and overall mortality, amounting to a 25% reduction in relative terms. This information should be included when

Breast-conserving therapy with partial or whole breast irradiation: ten-year results of the Budapest randomized trial.

Science.gov (United States)

Polgár, Csaba; Fodor, János; Major, Tibor; Sulyok, Zoltán; Kásler, Miklós

2013-08-01

To report the long-term results of a single-institution randomized study comparing the results of breast-conserving treatment with partial breast irradiation (PBI) or conventional whole breast irradiation (WBI). Between 1998 and 2004, 258 selected women with pT1 pN0-1mi M0, grade 1-2, non-lobular breast cancer without the presence of extensive intraductal component and resected with negative margins were randomized after BCS to receive 50 Gy WBI (n=130) or PBI (n=128). The latter consisted of either 7 × 5.2 Gy high-dose-rate (HDR) multi-catheter brachytherapy (BT; n=88) or 50 Gy electron beam (EB) irradiation (n=40). Primary endpoint was local recurrence (LR) as a first event. Secondary endpoints were overall survival (OS), cancer-specific survival (CSS), disease-free survival (DFS), and cosmetic results. After a median follow up of 10.2 years, the ten-year actuarial rate of LR was 5.9% and 5.1% in PBI and WBI arms, respectively (p=0.77). There was no significant difference in the ten-year probability of OS (80% vs 82%), CSS (94% vs 92%), and DFS (85% vs 84%), either. The rate of excellent-good cosmetic result was 81% in the PBI, and 63% in the control group (p<0.01). Partial breast irradiation delivered by interstitial HDR BT or EB for a selected group of early-stage breast cancer patients produces similar ten-year results to those achieved with conventional WBI. Significantly better cosmetic outcome can be achieved with HDR BT implants compared with the outcome after WBI. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Breast-conserving therapy with partial or whole breast irradiation: Ten-year results of the Budapest randomized trial

International Nuclear Information System (INIS)

Polgár, Csaba; Fodor, János; Major, Tibor; Sulyok, Zoltán; Kásler, Miklós

2013-01-01

Background and purpose: To report the long-term results of a single-institution randomized study comparing the results of breast-conserving treatment with partial breast irradiation (PBI) or conventional whole breast irradiation (WBI). Patients and methods: Between 1998 and 2004, 258 selected women with pT1 pN0-1mi M0, grade 1–2, non-lobular breast cancer without the presence of extensive intraductal component and resected with negative margins were randomized after BCS to receive 50 Gy WBI (n = 130) or PBI (n = 128). The latter consisted of either 7 × 5.2 Gy high-dose-rate (HDR) multi-catheter brachytherapy (BT; n = 88) or 50 Gy electron beam (EB) irradiation (n = 40). Primary endpoint was local recurrence (LR) as a first event. Secondary endpoints were overall survival (OS), cancer-specific survival (CSS), disease-free survival (DFS), and cosmetic results. Results: After a median follow up of 10.2 years, the ten-year actuarial rate of LR was 5.9% and 5.1% in PBI and WBI arms, respectively (p = 0.77). There was no significant difference in the ten-year probability of OS (80% vs 82%), CSS (94% vs 92%), and DFS (85% vs 84%), either. The rate of excellent-good cosmetic result was 81% in the PBI, and 63% in the control group (p < 0.01). Conclusions: Partial breast irradiation delivered by interstitial HDR BT or EB for a selected group of early-stage breast cancer patients produces similar ten-year results to those achieved with conventional WBI. Significantly better cosmetic outcome can be achieved with HDR BT implants compared with the outcome after WBI

An MGF-based unified framework to determine the joint statistics of partial sums of ordered random variables

KAUST Repository

Nam, Sungsik; Alouini, Mohamed-Slim; Yang, Hongchuan

2010-01-01

Order statistics find applications in various areas of communications and signal processing. In this paper, we introduce an unified analytical framework to determine the joint statistics of partial sums of ordered random variables (RVs

Experimental and simulation analysis of hydrogen production by partial oxidation of methanol

Energy Technology Data Exchange (ETDEWEB)

Sikander, U. [National Univ. of Science and Technology, Islamabad (Pakistan)

2014-10-15

Partial oxidation of methanol is the only self-sustaining process for onboard production of hydrogen. For this a fixed bed catalytic reactor is designed, based on heterogeneous catalytic reaction. To develop an optimized process, simulation is carried out using ASPEN HYSYS v 7.1. Reaction kinetics is developed on the basis of Langmuir Hinshel wood model. 45:55:5 of CuO: ZnO: Al/sub 2/O/sub 3/ is used as a catalyst. Simulation results are studied in detail to understand the phenomenon of partial oxidation of methanol inside the reactor. An experimental rig is developed for hydrogen production through partial oxidation of methanol. Results obtained from process simulation and experimental work; are compared with each other. (author)

Non-invasive multiwavelength photoplethysmography under low partial pressure of oxygen.

Science.gov (United States)

Fang, Yung Chieh; Tai, Cheng-Chi

2016-08-01

A reduction in partial pressure of oxygen in the environment may be caused by a gain in altitude, which reduces the atmospheric pressure; it may also be caused by the carbon dioxide generated from breathing in an enclosed space. Does inhaling oxygen of lower partial pressure affect the oxygen-carrying function of haemoglobin in vivo? This study uses non-invasive multiwavelength photoplethysmography to measure the effects that inhaling this type of oxygen can have on the plethysmography of the appendages of the body (fingertips). The results indicate that under low partial pressure of oxygen, be it the result of a gain in carbon dioxide concentration or altitude, the change in visible light absorption is the biggest for short wavelengths (approximately 620 or 640 nm) near deoxyhaemoglobin, which has higher absorption coefficient. Moreover, increasing carbon dioxide concentration from 5000 to 10,000 ppm doubly reduces the absorption rate of these short wavelengths.

Electrochemical promotion of catalytic reactions with Pt/C (or Pt/Ru/C)//PBI catalysts

DEFF Research Database (Denmark)

Petrushina, Irina; Bjerrum, Niels; Bandur, Viktor

2007-01-01

The paper is an overview of the results of the investigation on electrochemical promotion of three catalytic reactions: methane oxidation with oxygen, NO reduction with hydrogen at 135 degrees C and Fischer-Tropsch synthesis (FTS) at 170 degrees C in the [CH4/O-2(or NO/H-2 or CO/H-2)/Ar//Pt(or Pt....../Ru)//PBI(H3PO4)/H-2, Ar] fuel cell. It has been shown that the partial methane oxidation to C2H2 and the C-2 selectivity were electrochemically promoted by the negative catalyst polarization. This was also the case in NO reduction with hydrogen for low NO and H-2 partial pressures. In both cases the catalytic...... reactions have been promoted by the electrochemically produced hydrogen. It has been found that the NO reduction with hydrogen on the Pt/PBI strongly depends on NO and hydrogen partial pressures in the working gas mixture. At higher NO and H-2 partial pressures the catalysis is promoted...

Neuron-specific regulation of class I PI3K catalytic subunits and their dysfunction in brain disorders

Directory of Open Access Journals (Sweden)

Christina eGross

2014-02-01

Full Text Available The PI3K complex plays important roles in virtually all cells of the body. The enzymatic activity of PI3K to phosphorylate phosphoinositides in the membrane is mediated by a group of catalytic and regulatory subunits. Among those, the class I catalytic subunits, p110α, p110β, p110γ and p110δ, have recently drawn attention in the neuroscience field due to their specific dysregulation in diverse brain disorders. While in non-neuronal cells these catalytic subunits may have partially redundant functions, there is increasing evidence that in neurons their roles are more specialized, and confined to distinct receptor-dependent pathways. This review will summarize the emerging role of class I PI3K catalytic subunits in neurotransmitter-regulated neuronal signaling, and their dysfunction in a variety of neurological diseases, including fragile X syndrome, schizophrenia and epilepsy. We will discuss recent literature describing the use of PI3K subunit-selective inhibitors to rescue brain disease-associated phenotypes in in vitro and animal models. These studies give rise to the exciting prospect that these drugs, originally designed for cancer treatment, may be repurposed as therapeutic drugs for brain disorders in the future.

Thermal plasma treatment of stormwater sediments: comparison between DC non-transferred and partially transferred arc plasma.

Science.gov (United States)

Li, O L; Guo, Y; Chang, J S; Saito, N

2015-01-01

The disposal of enormous amount of stormwater sediments becomes an emerging worldwide problem. Stormwater sediments are contaminated by heavy metals, phosphorus, trace organic and hydrocarbons, and cannot be disposed without treatment. Thermal plasma decontamination technology offers a high decomposition rate in a wide range of toxic organic compound and immobilization of heavy metal. In this study, we compared the treatment results between two different modes of thermal plasma: (1) a non-transferred direct current (DC) mode and (2) a partial DC-transferred mode. The reductions of total organic carbon (TOC) were, respectively, 25% and 80% for non-transferred and partially transferred plasma, respectively. Most of the toxic organic compounds were converted majorly to CxHy. In the gaseous emission, the accumulated CxHy, CO, NO and H2S were significantly higher in partially transferred mode than in non-transferred mode. The solid analysis demonstrated that the concentrations of Ca and Fe were enriched by 500% and 40%, respectively. New chemical compositions such as KAlSi3O8, Fe3O4, NaCl and CaSO4 were formed after treatment in partially DC-transferred mode. The power inputs were 1 and 10 kW, respectively, for non-transferred DC mode and a partially DC-transferred mode. With a lower energy input, non-transferred plasma treatment can be used for decontamination of sediments with low TOC and metal concentration. Meanwhile, partially transferred thermal plasma with higher energy input is suitable for treating sediments with high TOC percentage and volatile metal concentration. The organic compounds are converted into valuable gaseous products which can be recycled as an energy source.

Methods of using structures including catalytic materials disposed within porous zeolite materials to synthesize hydrocarbons

Science.gov (United States)

Rollins, Harry W [Idaho Falls, ID; Petkovic, Lucia M [Idaho Falls, ID; Ginosar, Daniel M [Idaho Falls, ID

2011-02-01

Catalytic structures include a catalytic material disposed within a zeolite material. The catalytic material may be capable of catalyzing a formation of methanol from carbon monoxide and/or carbon dioxide, and the zeolite material may be capable of catalyzing a formation of hydrocarbon molecules from methanol. The catalytic material may include copper and zinc oxide. The zeolite material may include a first plurality of pores substantially defined by a crystal structure of the zeolite material and a second plurality of pores dispersed throughout the zeolite material. Systems for synthesizing hydrocarbon molecules also include catalytic structures. Methods for synthesizing hydrocarbon molecules include contacting hydrogen and at least one of carbon monoxide and carbon dioxide with such catalytic structures. Catalytic structures are fabricated by forming a zeolite material at least partially around a template structure, removing the template structure, and introducing a catalytic material into the zeolite material.

A partially reflecting random walk on spheres algorithm for electrical impedance tomography

Energy Technology Data Exchange (ETDEWEB)

Maire, Sylvain, E-mail: maire@univ-tln.fr [Laboratoire LSIS Equipe Signal et Image, Université du Sud Toulon-Var, Av. Georges Pompidou, BP 56, 83162 La Valette du Var Cedex (France); Simon, Martin, E-mail: simon@math.uni-mainz.de [Institute of Mathematics, Johannes Gutenberg University, 55099 Mainz (Germany)

2015-12-15

In this work, we develop a probabilistic estimator for the voltage-to-current map arising in electrical impedance tomography. This novel so-called partially reflecting random walk on spheres estimator enables Monte Carlo methods to compute the voltage-to-current map in an embarrassingly parallel manner, which is an important issue with regard to the corresponding inverse problem. Our method uses the well-known random walk on spheres algorithm inside subdomains where the diffusion coefficient is constant and employs replacement techniques motivated by finite difference discretization to deal with both mixed boundary conditions and interface transmission conditions. We analyze the global bias and the variance of the new estimator both theoretically and experimentally. Subsequently, the variance of the new estimator is considerably reduced via a novel control variate conditional sampling technique which yields a highly efficient hybrid forward solver coupling probabilistic and deterministic algorithms.

Non-catalytic direct synthesis of graphene on Si (111) wafers by using inductively-coupled plasma chemical vapor deposition

Science.gov (United States)

Hwang, Sung Won; Shin, Hyunho; Lee, Bongsoo; Choi, Suk-Ho

2016-08-01

We employ inductively-coupled plasma chemical vapor deposition for non-catalytic growth of graphene on a Si (111) wafer or glass substrate, which is useful for practical device applications of graphene without transfer processes. At a RF power (P) of 500 W under C2H2 flow, defect-free 3 ˜ 5-layer graphene is grown on Si (111) wafers, but on glass substrate, the layer is thicker and defective, as characterized by Raman spectroscopy and electron microscopy. The graphene is produced on Si (111) for P down to 190 W whereas it is almost not formed on glass for P < 250 W, possibly resulting from the weak catalytic-reaction-like effect on glass. These results are discussed based on possible growth mechanisms.

A biorthogonal decomposition for the identification and simulation of non-stationary and non-Gaussian random fields

Energy Technology Data Exchange (ETDEWEB)

Zentner, I. [IMSIA, UMR EDF-ENSTA-CNRS-CEA 9219, Université Paris-Saclay, 828 Boulevard des Maréchaux, 91762 Palaiseau Cedex (France); Ferré, G., E-mail: gregoire.ferre@ponts.org [CERMICS – Ecole des Ponts ParisTech, 6 et 8 avenue Blaise Pascal, Cité Descartes, Champs sur Marne, 77455 Marne la Vallée Cedex 2 (France); Poirion, F. [Department of Structural Dynamics and Aeroelasticity, ONERA, BP 72, 29 avenue de la Division Leclerc, 92322 Chatillon Cedex (France); Benoit, M. [Institut de Recherche sur les Phénomènes Hors Equilibre (IRPHE), UMR 7342 (CNRS, Aix-Marseille Université, Ecole Centrale Marseille), 49 rue Frédéric Joliot-Curie, BP 146, 13384 Marseille Cedex 13 (France)

2016-06-01

In this paper, a new method for the identification and simulation of non-Gaussian and non-stationary stochastic fields given a database is proposed. It is based on two successive biorthogonal decompositions aiming at representing spatio–temporal stochastic fields. The proposed double expansion allows to build the model even in the case of large-size problems by separating the time, space and random parts of the field. A Gaussian kernel estimator is used to simulate the high dimensional set of random variables appearing in the decomposition. The capability of the method to reproduce the non-stationary and non-Gaussian features of random phenomena is illustrated by applications to earthquakes (seismic ground motion) and sea states (wave heights).

Experimental optimization of catalytic process in-situ for heavy oil and bitumen upgrading

Energy Technology Data Exchange (ETDEWEB)

Shah, A.; Fishwick, R.P.; Leeke, G.A.; Wood, J. [Birmingham Univ., Birmingham (United Kingdom); Rigby, S.P.; Greaves, M. [Bath Univ., Bath (United Kingdom)

2010-07-01

Peak crude oil production is expected to occur in the second decade of this century, followed by a phase of permanent decline in conventional crude oil production. However, very large resources of heavy oil and bitumen exist throughout the world, most notably in Canada and Venezuela. The high viscosity and density of these non-conventional crude oils require more energy intensive operations for production and upgrading, and also for transportation. As such, they are more costly to extract. This paper described some of the technological innovations that are being considered to extract heavier oil supplies with reduced environmental impact. The toe-to-heel air injection (THAI) process and its catalytic added-on (CAPRI) process combine in-situ combustion with catalytic upgrading using an annular catalyst packed around a horizontal producer well. Results of an experimental study concerning optimization of catalyst type and operating conditions showed that CAPRI can effect further upgrading of partially upgraded THAI oil, with upgrading levels of viscosity and API gravity dependent upon temperature and flow rate. 20 refs., 8 tabs., 10 figs.

Acidogenesis driven by hydrogen partial pressure towards bioethanol production through fatty acids reduction

International Nuclear Information System (INIS)

Sarkar, Omprakash; Butti, Sai Kishore; Venkata Mohan, S.

2017-01-01

H 2 partial pressure drives the reduction of carboxylic acid (short chain fatty acids) formed as primary metabolites in acidogenic fermentation to form bioalcohols. Microbial catalysis under the influence of H 2 partial pressure was evaluated in comparison with a reactor operated at atmospheric pressure under identical conditions. Carboxylic acid reduction gets regulated selectively by the influence of elevated pressures and redox conditions, resulting in the formation of alcohols. The non-equilibrium of the intra and extracellular H 2 ions causes the anaerobic bacteria to alter their pathways as a function of interspecies H 2 transfer. Ethanol production was quantified, as acetic acid was the major carboxylic acid synthesised during acidogenesis. H 2 pressure influenced the electrochemical activity which was reflected in the distinct variation of the electron transfer rates and the catalytic activity of redox mediators (NAD + /NADH, flavoproteins and iron-sulphur clusters). The bioprocess depicted in this communication depicted a non-genetic regulation of product formation, understanding the acidogenic metabolism and alternate route for alcohol production. - Highlights: • H 2 partial pressure in HPR aided in the reduction of carboxylic acids to alcohols. • Production and consumption rate of VFAs were correlating with alcohol formation. • Metabolic shift was evident with bioelectrochical analysis. • NADH/NAD + ratio and H 2 partial pressure coupled in enhanced solventogenesis.

Non-ionic Surfactants and Non-Catalytic Protein Treatment on Enzymatic Hydrolysis of Pretreated Creeping Wild Ryegrass

Science.gov (United States)

Zheng, Yi; Pan, Zhongli; Zhang, Ruihong; Wang, Donghai; Jenkins, Bryan

Our previous research has shown that saline Creeping Wild Ryegrass (CWR), Leymus triticoides, has a great potential to be used for bioethanol production because of its high fermentable sugar yield, up to 85% cellulose conversion of pretreated CWR. However, the high cost of enzyme is still one of the obstacles making large-scale lignocellulosic bioethanol production economically difficult. It is desirable to use reduced enzyme loading to produce fermentable sugars with high yield and low cost. To reduce the enzyme loading, the effect of addition of non-ionic surfactants and non-catalytic protein on the enzymatic hydrolysis of pretreated CWR was investigated in this study. Tween 20, Tween 80, and bovine serum albumin (BSA) were used as additives to improve the enzymatic hydrolysis of dilute sulfuric-acid-pretreated CWR. Under the loading of 0.1 g additives/g dry solid, Tween 20 was the most effective additive, followed by Tween 80 and BSA. With the addition of Tween 20 mixed with cellulase loading of 15 FPU/g cellulose, the cellulose conversion increased 14% (from 75 to 89%), which was similar to that with cellulase loading of 30 FPU/g cellulose and without additive addition. The results of cellulase and BSA adsorption on the Avicel PH101, pretreated CWR, and lignaceous residue of pretreated CWR support the theory that the primary mechanism behind the additives is prevention of non-productive adsorption of enzymes on lignaceous material of pretreated CWR. The addition of additives could be a promising technology to improve the enzymatic hydrolysis by reducing the enzyme activity loss caused by non-productive adsorption.

Catalytic modification of cellulose and hemicellulose - Sugarefine

Energy Technology Data Exchange (ETDEWEB)

Repo, T. [Helsinki Univ. (Finland),Laboratory of Inorganic Chemistry], email: timo.repo@helsinki.fi

2012-07-01

The main goal of the project is to develop catalytic methods for the modification of lignocellulose-based saccharides in the biorefineries. The products of these reactions could be used for example as biofuel components, raw materials for the chemical industry, solvents and precursors for biopolymers. The catalyst development aims at creating efficient, selective and green catalytic methods for profitable use in biorefineries. The project is divided in three work packages: In WP1 (Catalytic dehydration of cellulose) the aim is at developing non-toxic, efficient methods for the catalytic dehydration of cellulose the target molecule being here 5-hydroxymethylfurfural (5-HMF). 5-HMF is an interesting platform chemical for the production of fuel additives, solvents and polymers. In WP2 (Catalytic reduction), the objective of the catalytic reduction studies is to produce commercially interesting monofunctional chemicals, such as 1-butanol or 2-methyltetrahydrofuran (2-MeTHF). In WP3 (Catalytic oxidation), the research focuses on developing a green and efficient oxidation method for producing acids. Whereas acetic and formic acids are bulk chemicals, diacids such as glucaric and xylaric acids are valuable specialty chemicals for detergent, polymer and food production.

PINGU: PredIction of eNzyme catalytic residues usinG seqUence information.

Directory of Open Access Journals (Sweden)

Priyadarshini P Pai

Full Text Available Identification of catalytic residues can help unveil interesting attributes of enzyme function for various therapeutic and industrial applications. Based on their biochemical roles, the number of catalytic residues and sequence lengths of enzymes vary. This article describes a prediction approach (PINGU for such a scenario. It uses models trained using physicochemical properties and evolutionary information of 650 non-redundant enzymes (2136 catalytic residues in a support vector machines architecture. Independent testing on 200 non-redundant enzymes (683 catalytic residues in predefined prediction settings, i.e., with non-catalytic per catalytic residue ranging from 1 to 30, suggested that the prediction approach was highly sensitive and specific, i.e., 80% or above, over the incremental challenges. To learn more about the discriminatory power of PINGU in real scenarios, where the prediction challenge is variable and susceptible to high false positives, the best model from independent testing was used on 60 diverse enzymes. Results suggested that PINGU was able to identify most catalytic residues and non-catalytic residues properly with 80% or above accuracy, sensitivity and specificity. The effect of false positives on precision was addressed in this study by application of predicted ligand-binding residue information as a post-processing filter. An overall improvement of 20% in F-measure and 0.138 in Correlation Coefficient with 16% enhanced precision could be achieved. On account of its encouraging performance, PINGU is hoped to have eventual applications in boosting enzyme engineering and novel drug discovery.

Biodiesel production through non-catalytic supercritical transesterification: current state and perspectives

Directory of Open Access Journals (Sweden)

C. da Silva

2014-06-01

Full Text Available The inconveniences of the conventional method for biodiesel production by alkaline catalysis suggests research towards alternative methods, with the non-catalytic transesterification using an alcohol at supercritical conditions proposed as a promising technique for biodiesel production. The so-called supercritical method (SCM has powerful advantages over conventional techniques, such as fast reaction rates, feedstock flexibility, production efficiency and environmentally friendly benefits. However, application of this methodology has some limitations, like operating conditions (elevated temperature and pressure and higher amounts of alcohol, which result in high energy costs and degradation of the products generated. In this review paper the state of the art in relation to the use of the SCM for biodiesel production is reported and discussed, describing the characteristics of the method, the influence of operational parameters on the ester yield, patents available in the field and the perspectives for application of the technique.

Randomized controlled clinical trial of behavioral lifestyle intervention with partial meal replacement to reduce excessive gestational weight gain.

Science.gov (United States)

Phelan, Suzanne; Wing, Rena R; Brannen, Anna; McHugh, Angelica; Hagobian, Todd A; Schaffner, Andrew; Jelalian, Elissa; Hart, Chantelle N; Scholl, Theresa O; Munoz-Christian, Karen; Yin, Elaine; Phipps, Maureen G; Keadle, Sarah; Abrams, Barbara

2018-02-01

Behavioral lifestyle interventions during pregnancy can prevent excessive gestational weight gain (GWG) in women with normal weight; however, effective interventions to reduce GWG in ethnically diverse women with obesity are lacking. A randomized controlled trial was conducted to test whether a behavioral lifestyle intervention with partial meal replacement reduces GWG rate in Hispanic and non-Hispanic women with overweight or obesity relative to enhanced usual care. Participants (n = 257) were recruited in San Luis Obispo, California, and Providence, Rhode Island, between November 2012 and May 2016. Participants were pregnant (mean ± SD: 13.6 ± 1.8 wk of gestation) with overweight or obesity and had a mean age of 30.3 y; 41.6% of participants were Hispanic. Women were randomly assigned within site and by ethnicity to enhanced usual care (n = 128) or to a behavioral lifestyle intervention with partial meal replacement (n = 129). The primary outcome was GWG per week of observation. Secondary outcomes were proportions exceeding Institute of Medicine (IOM) guidelines for total GWG, changes in weight-control behaviors and cardiovascular disease risk factors, and incidence of pregnancy complications. Study retention was 99.6% (256 of 257). The intervention compared with usual care resulted in less mean ± SD weekly GWG (0.33 ± 0.25 compared with 0.39 ± 0.23 kg/wk; P = 0.02) and total GWG (9.4 ± 6.9 compared with 11.2 ± 7.0 kg; P = 0.03) and reduced the proportion of women who exceeded IOM guidelines for total GWG (41.1% compared with 53.9%; P = 0.03). No significant group × time × demographic subgroup (ethnicity, BMI, age, parity, and income) interactions were observed. Among intervention participants, greater meal replacement intake was related to reduced GWG rate (β = -0.07; 95% CI:-0.12, -0.03; P = 0.002). The intervention compared with usual care increased weight-control strategies (P meal replacement significantly reduced GWG in Hispanic

Partially Cystic Thyroid Nodules: Ultrasound Findings of Malignancy

Energy Technology Data Exchange (ETDEWEB)

Park, Jang Mi; Choi, Yoon Jung; Kwag, Hyon Joo [Dept. of Radiology, Kangbuk Samsung Hospital, Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of)

2012-09-15

To seek for the ultrasound (US) findings of partially cystic thyroid nodules that are associated with malignancy. We reviewed the US characteristics of 22 surgically confirmed partially cystic papillary carcinomas, and compared them with those of 80 benign partially cystic nodules. The review cases were selected in a random order from a total of 1029 partially cystic nodules that were diagnosed with an US-guided fine needle aspiration biopsy over a period of 8 years (June 2003 to October 2010) at our institution. In partially cystic thyroid nodules, a taller-than-wide shape (100%, p<0.001) and spiculated or microlobulated margin (58.3%, p 0.003) were significantly associated with malignancy. In terms of internal solid portion of the nodule, eccentric configuration (68.0%, p<0.001), non-smooth margin (81.3%, p<0.001), hypoechogenecity (30.0%, p<0.042), and microcalcification (89.5%, p<0.001) were more frequently demonstrated in malignant nodules than benign ones. In partially cystic thyroid nodules, understanding the characteristics of US findings is important to make a precise diagnosis of malignant nodules.

What Can We Learn in Electrocatalysis, from Nanoparticulated Precious and/or Non-Precious Catalytic Centers Interacting with Their Support?

Directory of Open Access Journals (Sweden)

Juan Manuel Mora-Hernández

2016-09-01

Full Text Available This review is devoted to discussing the state of the art in the relevant aspects of the synthesis of novel precious and non-precious electrocatalysts. It covers the production of Pt- and Pd-based electrocatalysts synthesized by the carbonyl chemical route, the synthesis description for the preparation of the most catalytically active transition metal chalcogenides, then the employment of free-surfactants synthesis routes to produce non-precious electrocatalysts. A compilation of the best precious electrocatalysts to perform the hydrogen oxidation reaction (HOR is described; a section is devoted to the synthesis and electrocatalytic evaluation of non-precious materials which can be used to perform the HOR in alkaline medium. Apropos the oxygen reduction reaction (ORR, the synthesis and modification of the supports is also discussed as well, aiming at describing the state of the art to improve kinetics of low temperature fuel cell reactions via the hybridization process of the catalytic center with a variety of carbon-based, and ceramic-carbon supports. Last, but not least, the review covers the experimental half-cells results in a micro-fuel cell platform obtained in our laboratory, and by other workers, analyzing the history of the first micro-fuel cell systems and their tailoring throughout the time bestowing to the design and operating conditions.

Partial oxidation of 2-propanol on perovskites

Energy Technology Data Exchange (ETDEWEB)

Sumathi, R.; Viswanathan, B.; Varadarajan, T.K. [Indian Inst. of Tech., Madras (India). Dept. of Chemistry

1998-12-31

Partial oxidation of 2-propanol was carried out on AB{sub 1-x}B`{sub x}O{sub 3} (A=Ba, B=Pb, Ce, Ti; B`=Bi, Sb and Cu) type perovskite oxides. Acetone was the major product observed on all the catalysts. All the catalysts underwent partial reduction during the reaction depending on the composition of the reactant, nature of the B site cation and the extent of substitution at B site. The catalytic activity has been correlated with the reducibility of the perovskite oxides determined from Temperature Programmed Reduction (TPR) studies. (orig.)

Studies on the Catalytic Properties of Partially Purified Alkaline Proteases from Some Selected Microorganisms

Directory of Open Access Journals (Sweden)

Titilayo Olufunke Femi-Ola

2012-09-01

Full Text Available Aims: The research was done to study the conditions enhancing catalytic activities of alkaline proteases from Vibro sp., Lactobacillus brevis, Zymomonas sp., Athrobacter sp., Corynebacterium sp. and Bacillus subtilis.Methodology and Results: The proteolytic enzymes were purified in 2-step procedures involving ammonium sulphate precipitation and sephadex G-150 gel permeation chromatography. The upper and lower limits for the specific activities of proteases from the selected microorganisms were estimated at 20.63 and 47.51 units/mg protein with Zymomonas protease having the highest specific activity towards casein as its substrate and purification fold of 3.46, while that ofLactobacillus brevis protease was 8.06. The native molecular weights of these active proteins ranged from 30.4 to 45.7 kDa with Athrobacter sp. protease having the highest weight for its subunits. The proteolytic enzymes had optimum pH range of 8 to 10 and temperature range of 50 to 62 ºC accounting for the percentage relative activity range of 75 to 94% and 71 to 84 % respectively. The activities of Lactobacillus brevis and Bacillus subtilis proteases were maximum at pH 9 and 10 respectively. Lactobacillus brevis protease activity was maximum at temperature of 62 ºC, while beyond this value, a general thermal instability of these active proteins was observed. At above 70 ºC, the catalytic activities of Corynebacterium sp., Vibrio sp., Zymomonas sp. and Arthrobacter sp. proteases were progressively reduced over a period of 120 min of incubation, while Bacillus subtlis and Lactobacillus brevis proteases were relatively stable. Effect of metal ions was investigated on the catalytic activity of protease from the microorganisms. Lactobacillus brevis,Zymomonas sp., Arthrobacter sp., Corynebacterium sp. and Bacillus subtilis protease activities were strongly activated by metal ions such as Ca+2 and Mg+2. Enzyme activities were inhibited strongly by Cu2+ and Hg2+ but were not

On the complete and partial integrability of non-Hamiltonian systems

Science.gov (United States)

Bountis, T. C.; Ramani, A.; Grammaticos, B.; Dorizzi, B.

1984-11-01

The methods of singularity analysis are applied to several third order non-Hamiltonian systems of physical significance including the Lotka-Volterra equations, the three-wave interaction and the Rikitake dynamo model. Complete integrability is defined and new completely integrable systems are discovered by means of the Painlevé property. In all these cases we obtain integrals, which reduce the equations either to a final quadrature or to an irreducible second order ordinary differential equation (ODE) solved by Painlevé transcendents. Relaxing the Painlevé property we find many partially integrable cases whose movable singularities are poles at leading order, with In( t- t0) terms entering at higher orders. In an Nth order, generalized Rössler model a precise relation is established between the partial fulfillment of the Painlevé conditions and the existence of N - 2 integrals of the motion.

Basis adaptation and domain decomposition for steady-state partial differential equations with random coefficients

Energy Technology Data Exchange (ETDEWEB)

Tipireddy, R.; Stinis, P.; Tartakovsky, A. M.

2017-12-01

We present a novel approach for solving steady-state stochastic partial differential equations (PDEs) with high-dimensional random parameter space. The proposed approach combines spatial domain decomposition with basis adaptation for each subdomain. The basis adaptation is used to address the curse of dimensionality by constructing an accurate low-dimensional representation of the stochastic PDE solution (probability density function and/or its leading statistical moments) in each subdomain. Restricting the basis adaptation to a specific subdomain affords finding a locally accurate solution. Then, the solutions from all of the subdomains are stitched together to provide a global solution. We support our construction with numerical experiments for a steady-state diffusion equation with a random spatially dependent coefficient. Our results show that highly accurate global solutions can be obtained with significantly reduced computational costs.

Catalytic gasification of oil-shales

Energy Technology Data Exchange (ETDEWEB)

Lapidus, A.; Avakyan, T. [I.M. Gubkin Russian State Univ. of Oil and Gas, Moscow (Russian Federation); Strizhakova, Yu. [Samara State Univ. (Russian Federation)

2012-07-01

Nowadays, the problem of complex usage of solid fossil fuels as raw materials for obtaining of motor fuels and chemical products is becoming increasingly important. A one of possible solutions of the problem is their gasification with further processing of gaseous and liquid products. In this work we have investigated the process of thermal and catalytic gasification of Baltic and Kashpir oil-shales. We have shown that, as compared with non-catalytic process, using of nickel catalyst in the reaction increases the yield of gas, as well as hydrogen content in it, and decreases the amount of liquid products. (orig.)

Hyperfractionated Radiotherapy Following Induction Chemotherapy for Stage III Non-Small Cell Lung Cancer-Random iced for Adjuvant Chemotherapy vs. Observation

International Nuclear Information System (INIS)

Choi, Eun Kyung; Chang, Hye Sook; Ahn, Seung Do

1993-01-01

Since Jan. 1991 a prospective randomized study for Stage III unresectable non small cell lung cancer(NSCLC) has been conducted to evaluate the response rate and tolerance of induction chemotherapy with MVP followed by hyperfractionated radiotherapy and evaluate the efficacy of maintenance chemotherapy in Asan Medical Center. All patients in this study were treated with hypefractionated radiotherapy (120 cGy/fx BID, 0480 cGy/54 fx) following 3 cycles of induction chemotherapy, MVP (Mitomycin C 6 mg/m2, Vinblastin B mg/ m2, Cisplatin 60 Mg/ m2) and then the partial and complete responders from induction chemotherapy were randomized to 3 cycles of adjuvant MVP chemotherapy group and observation group. 48 patients were registered to this study until December 1992; among 48 patients 3 refused further treatment after induction chemotherapy and 6 received incomplete radiation therapy because of patient refusal, 39 completed planned therapy. Twenty-three(58%) patients including 2 complete responders showed response from induction chemotherapy. Among the 21 patients who achieved a partial response after induction chemotherapy, 1 patient rendered complete clearance of disease and 10 patients showed further regression of tumor following hypefractionated radiotherapy. Remaining 10 patients showed stable disease or progression after radiotherapy. Of the sixteen patients judged to have stable disease or progression after induction chemotherapy, seven showed more than partial remission after radiotherapy but nine showed no response in spite of radiotherapy. Of the 35 patients who completed induction chemotherapy and radiotherapy, 25 patients(64%) including 3 complete responders showed more than partial remission. Nineteen patients were randomized after radiotherapy. Nine patients were allocated to adjuvant chemotherapy group and 4/9 shewed further regression of tumor after adjuvant chemotherapy. For the time being, there is no suggestion of a difference between the adjuvant

Non-Catalytic and MgSO4 - Catalyst based Degradation of Glycerol in Subcritical and Supercritical Water Media

Directory of Open Access Journals (Sweden)

Mahfud Mahfud

2011-02-01

Full Text Available This research aims to study the glycerol degradation reaction in subcritical and supercritical water media. The degradation of glycerol into other products was performed both with sulphate salt catalysts and without catalyst. The reactant was made from glycerol and water with the mass ratio of 1:10. The experiments were carried out using a batch reactor at a constant pressure of 250 kgf/cm2, with the temperature range of 200-400oC, reaction time of 30 minutes, and catalyst mol ratio in glycerol of 1:10 and 1:8. The products of the non-catalytic glycerol degradation were acetaldehyde, methanol, and ethanol. The use of sulphate salt as catalyst has high selectivity to acetaldehyde and still allows the formation alcohol product in small quantities. The mechanism of ionic reaction and free radical reaction can occur at lower temperature in hydrothermal area or subcritical water. Conversion of glycerol on catalytic reaction showed a higher yield when compared with the reaction performed without catalyst

Reduced basis ANOVA methods for partial differential equations with high-dimensional random inputs

Energy Technology Data Exchange (ETDEWEB)

Liao, Qifeng, E-mail: liaoqf@shanghaitech.edu.cn [School of Information Science and Technology, ShanghaiTech University, Shanghai 200031 (China); Lin, Guang, E-mail: guanglin@purdue.edu [Department of Mathematics & School of Mechanical Engineering, Purdue University, West Lafayette, IN 47907 (United States)

2016-07-15

In this paper we present a reduced basis ANOVA approach for partial deferential equations (PDEs) with random inputs. The ANOVA method combined with stochastic collocation methods provides model reduction in high-dimensional parameter space through decomposing high-dimensional inputs into unions of low-dimensional inputs. In this work, to further reduce the computational cost, we investigate spatial low-rank structures in the ANOVA-collocation method, and develop efficient spatial model reduction techniques using hierarchically generated reduced bases. We present a general mathematical framework of the methodology, validate its accuracy and demonstrate its efficiency with numerical experiments.

Non-classical radiation transport in random media with fluctuating densities

International Nuclear Information System (INIS)

Dyuldya, S.V.; Bratchenko, M.I.

2012-01-01

The ensemble averaged propagation kernels of the non-classical radiation transport are studied by means of the proposed application of the stochastic differential equation random medium generators. It is shown that the non-classical transport is favored in long-correlated weakly fluctuating media. The developed kernel models have been implemented in GEANT4 and validated against the d ouble Monte Carlo m odeling of absorptions curves of disperse neutron absorbers and γ-albedos from a scatterer/absorber random mix

Networks of high mutual information define the structural proximity of catalytic sites: implications for catalytic residue identification.

Directory of Open Access Journals (Sweden)

Cristina Marino Buslje

Full Text Available Identification of catalytic residues (CR is essential for the characterization of enzyme function. CR are, in general, conserved and located in the functional site of a protein in order to attain their function. However, many non-catalytic residues are highly conserved and not all CR are conserved throughout a given protein family making identification of CR a challenging task. Here, we put forward the hypothesis that CR carry a particular signature defined by networks of close proximity residues with high mutual information (MI, and that this signature can be applied to distinguish functional from other non-functional conserved residues. Using a data set of 434 Pfam families included in the catalytic site atlas (CSA database, we tested this hypothesis and demonstrated that MI can complement amino acid conservation scores to detect CR. The Kullback-Leibler (KL conservation measurement was shown to significantly outperform both the Shannon entropy and maximal frequency measurements. Residues in the proximity of catalytic sites were shown to be rich in shared MI. A structural proximity MI average score (termed pMI was demonstrated to be a strong predictor for CR, thus confirming the proposed hypothesis. A structural proximity conservation average score (termed pC was also calculated and demonstrated to carry distinct information from pMI. A catalytic likeliness score (Cls, combining the KL, pC and pMI measures, was shown to lead to significantly improved prediction accuracy. At a specificity of 0.90, the Cls method was found to have a sensitivity of 0.816. In summary, we demonstrate that networks of residues with high MI provide a distinct signature on CR and propose that such a signature should be present in other classes of functional residues where the requirement to maintain a particular function places limitations on the diversification of the structural environment along the course of evolution.

Networks of high mutual information define the structural proximity of catalytic sites: implications for catalytic residue identification.

Science.gov (United States)

Marino Buslje, Cristina; Teppa, Elin; Di Doménico, Tomas; Delfino, José María; Nielsen, Morten

2010-11-04

Identification of catalytic residues (CR) is essential for the characterization of enzyme function. CR are, in general, conserved and located in the functional site of a protein in order to attain their function. However, many non-catalytic residues are highly conserved and not all CR are conserved throughout a given protein family making identification of CR a challenging task. Here, we put forward the hypothesis that CR carry a particular signature defined by networks of close proximity residues with high mutual information (MI), and that this signature can be applied to distinguish functional from other non-functional conserved residues. Using a data set of 434 Pfam families included in the catalytic site atlas (CSA) database, we tested this hypothesis and demonstrated that MI can complement amino acid conservation scores to detect CR. The Kullback-Leibler (KL) conservation measurement was shown to significantly outperform both the Shannon entropy and maximal frequency measurements. Residues in the proximity of catalytic sites were shown to be rich in shared MI. A structural proximity MI average score (termed pMI) was demonstrated to be a strong predictor for CR, thus confirming the proposed hypothesis. A structural proximity conservation average score (termed pC) was also calculated and demonstrated to carry distinct information from pMI. A catalytic likeliness score (Cls), combining the KL, pC and pMI measures, was shown to lead to significantly improved prediction accuracy. At a specificity of 0.90, the Cls method was found to have a sensitivity of 0.816. In summary, we demonstrate that networks of residues with high MI provide a distinct signature on CR and propose that such a signature should be present in other classes of functional residues where the requirement to maintain a particular function places limitations on the diversification of the structural environment along the course of evolution.

Real-time definition of non-randomness in the distribution of genomic events.

Directory of Open Access Journals (Sweden)

Ulrich Abel

Full Text Available Features such as mutations or structural characteristics can be non-randomly or non-uniformly distributed within a genome. So far, computer simulations were required for statistical inferences on the distribution of sequence motifs. Here, we show that these analyses are possible using an analytical, mathematical approach. For the assessment of non-randomness, our calculations only require information including genome size, number of (sampled sequence motifs and distance parameters. We have developed computer programs evaluating our analytical formulas for the real-time determination of expected values and p-values. This approach permits a flexible cluster definition that can be applied to most effectively identify non-random or non-uniform sequence motif distribution. As an example, we show the effectivity and reliability of our mathematical approach in clinical retroviral vector integration site distribution.

Weighted Scaling in Non-growth Random Networks

International Nuclear Information System (INIS)

Chen Guang; Yang Xuhua; Xu Xinli

2012-01-01

We propose a weighted model to explain the self-organizing formation of scale-free phenomenon in non-growth random networks. In this model, we use multiple-edges to represent the connections between vertices and define the weight of a multiple-edge as the total weights of all single-edges within it and the strength of a vertex as the sum of weights for those multiple-edges attached to it. The network evolves according to a vertex strength preferential selection mechanism. During the evolution process, the network always holds its total number of vertices and its total number of single-edges constantly. We show analytically and numerically that a network will form steady scale-free distributions with our model. The results show that a weighted non-growth random network can evolve into scale-free state. It is interesting that the network also obtains the character of an exponential edge weight distribution. Namely, coexistence of scale-free distribution and exponential distribution emerges.

Plasma-catalytic reforming of liquid hydrocarbons

International Nuclear Information System (INIS)

Nedybaliuk, O.A.; Chernyak, V.Ya; Kolgan, V.V.; Iukhymenko, V.V.; Solomenko, O.V.; Fedirchyk, I.I.; Martysh, E.V.; Demchina, V.P.; Klochok, N.V.; Dragnev, S.V.

2015-01-01

The series of experiments studying the plasma-catalytic reforming of liquid hydrocarbons was carried out. The dynamic plasma-liquid system based on a low-power rotating gliding arc with solid electrodes was used for the investigation of liquid hydrocarbons reforming process. Conversion was done via partial oxidation. A part of oxidant flow was activated by the discharge. Synthesis-gas composition was analysed by means of mass-spectrometry and gas-chromatography. A standard boiler, which operates on natural gas and LPG, was used for the burning of synthesis-gas

Effect of H-wave polarization on laser radar detection of partially convex targets in random media.

Science.gov (United States)

El-Ocla, Hosam

2010-07-01

A study on the performance of laser radar cross section (LRCS) of conducting targets with large sizes is investigated numerically in free space and random media. The LRCS is calculated using a boundary value method with beam wave incidence and H-wave polarization. Considered are those elements that contribute to the LRCS problem including random medium strength, target configuration, and beam width. The effect of the creeping waves, stimulated by H-polarization, on the LRCS behavior is manifested. Targets taking large sizes of up to five wavelengths are sufficiently larger than the beam width and are sufficient for considering fairly complex targets. Scatterers are assumed to have analytical partially convex contours with inflection points.

Catalytic properties of nickel ferrites for oxidation of glucose, β-nicotiamide adenine dinucleotide (NADH) and methanol

Energy Technology Data Exchange (ETDEWEB)

Galindo, R. [Departamento de Química, Universidad de Guanajuato, Cerro de la Venada s/n, Pueblito de Rocha, C.P. 36040 Guanajuato, Gto (Mexico); Departamento de Química Física Aplicada, Universidad Autónoma de Madrid, Cantoblanco s/n, C.P. 28049 Madrid (Spain); Gutiérrez, S. [Departamento de Química, Universidad de Guanajuato, Cerro de la Venada s/n, Pueblito de Rocha, C.P. 36040 Guanajuato, Gto (Mexico); Menéndez, N. [Departamento de Química Física Aplicada, Universidad Autónoma de Madrid, Cantoblanco s/n, C.P. 28049 Madrid (Spain); Herrasti, P., E-mail: pilar.herrasti@uam.es [Departamento de Química Física Aplicada, Universidad Autónoma de Madrid, Cantoblanco s/n, C.P. 28049 Madrid (Spain)

2014-02-15

Highlights: ► NiFe{sub 2}O{sub 4} nanoparticles obtained by electrochemical method are effective catalyst. ► A partially inverse spinel was obtained with 57% Fe{sup 3+} in tetrahedral position. ► A non-enzymatic electrode using NiFe{sub 2}O{sub 4} nanoparticles has been manufactured. -- Abstract: Nickel ferrite nanoparticles (NiFe{sub 2}O{sub 4}) were synthesized by electrochemical method and used as catalyst for direct oxidation of glucose, NADH and methanol. Characterization of these nanoparticles was carried out by X-ray diffraction, Mössbauer spectroscopy, and colloidal properties such as hydrodynamic radius and Zeta potential. To evaluate the catalytic properties of these nanoparticles against the oxidation process, paste graphite electrodes mixing nickel ferrites and different conductive materials (graphite, carbon nanotubes) and binders agents (mineral oil, 1-octylpyridinium hexafluorophosphate (nOPPF6)) were used. The results prove good catalytic properties of these materials, with an oxidation potential around 0.75, 0.5 and 0.8 V for glucose, NADH, and methanol, respectively.

Partially covered versus uncovered self-expandable nitinol stents with anti-migration properties for the palliation of malignant distal biliary obstruction: A randomized controlled trial.

Science.gov (United States)

Yang, Min Jae; Kim, Jin Hong; Yoo, Byung Moo; Hwang, Jae Chul; Yoo, Jun Hwan; Lee, Ki Seong; Kang, Joon Koo; Kim, Soon Sun; Lim, Sun Gyo; Shin, Sung Jae; Cheong, Jae Youn; Lee, Kee Myung; Lee, Kwang Jae; Cho, Sung Won

2015-01-01

Covered self-expandable metal stents (SEMSs) are increasingly used as alternatives to uncovered SEMSs for the palliation of inoperable malignant distal biliary obstruction to counteract tumor ingrowth. We aimed to compare the outcomes of partially covered and uncovered SEMSs with identical mesh structures and anti-migration properties, such as low axial force and flared ends. One hundred and three patients who were diagnosed with inoperable malignant distal biliary obstruction between January 2006 and August 2013 were randomly assigned to either the partially covered (n = 51) or uncovered (n = 52) SEMS group. There were no significant differences in the cumulative stent patency, overall patient survival, stent dysfunction-free survival and overall adverse events, including pancreatitis and cholecystitis, between the two groups. Compared to the uncovered group, stent migration (5.9% vs. 0%, p = 0.118) and tumor overgrowth (7.8% vs. 1.9%, p = 0.205) were non-significantly more frequent in the partially covered group, whereas tumor ingrowth showed a significantly higher incidence in the uncovered group (5.9% vs. 19.2%, p = 0.041). Stent migration in the partially covered group occurred only in patients with short stenosis of the utmost distal bile duct (two in ampullary cancer, one in bile duct cancer), and did not occur in any patients with pancreatic cancer. For the palliation of malignant distal biliary obstruction, endoscopic placement of partially covered SEMSs with anti-migration designs and identical mesh structures to uncovered SEMSs failed to prolong cumulative stent patency or reduce stent migration.

Microbiological analysis after complete or partial removal of carious dentin using two different techniques in primary teeth: A randomized clinical trial

Science.gov (United States)

Singhal, Deepak Kumar; Acharya, Shashidhar; Thakur, Arun Singh

2016-01-01

Background: The management of deep carious lesions can be done by various techniques but residual caries dilemma still persists and bacterial reduction in cavities treated by either partial or complete caries removal techniques is debatable. So the objective of the present randomized clinical trial was to compare microbial counts in cavities submitted to complete caries removal and partial caries removal using either hand instruments or burs before and after 3 weeks of restoration. Materials and Methods: Primary molars with acute carious lesions in inner half of dentine and vital pulp were randomly divided into three groups of 14 each: Group A: Partial caries removal using hand instruments atraumatic restorative treatment (ART) only; Group B: Partial caries removal using bur; Group C: Complete caries removal using bur and caries detector dye. Dentine sample obtained after caries removal and 3 weeks after restoration, were subjected to microbial culture and counting (colony-forming units [CFU]/mg of dentine) for total viable bacterial count, Streptococcus spp., mutans streptococci, Lactobacillus spp. Results: Three techniques of caries removal showed significant (P < 0.05) reduction in all microorganisms studied after 3 weeks of evaluation, but there was no statistically significant difference in percentage reduction of microbial count among three groups. Conclusion: Results suggest the use of partial caries removal in a single session as compared to complete caries removal as a part of treatment of deep lesions in deciduous teeth in order to reduce the risk of pulp exposure. Partial caries removal using ART can be preferred for community settings as public health procedure for caries management. PMID:26962313

Non Catalytic Transesterification of Vegetables Oil to Biodiesel in Sub-and Supercritical Methanol: A Kinetic’s Study

OpenAIRE

Nyoman Puspa Asri; Siti Machmudah; W. Wahyudiono; S. Suprapto; Kusno Budikarjono; Achmad Roesyadi; Motonobu Goto

2013-01-01

Non catalytic transesterification in sub and supercritical methanol have been used to produce biodiesel from palm oil and soybean oil. A kinetic study was done under reaction condition with temperature and time control. The experiments were carried out in a batch type reactor at reaction temperatures from 210 °C (subcritical condition) to 290 °C (the supercritical state) in the interval ranges of temperature of 20 °C and at various molar ratios of oil to methanol. The rate constants of the re...

Enhancement of the catalytic activity of ferulic acid decarboxylase from Enterobacter sp. Px6-4 through random and site-directed mutagenesis.

Science.gov (United States)

Lee, Hyunji; Park, Jiyoung; Jung, Chaewon; Han, Dongfei; Seo, Jiyoung; Ahn, Joong-Hoon; Chong, Youhoon; Hur, Hor-Gil

2015-11-01

The enzyme ferulic acid decarboxylase (FADase) from Enterobacter sp. Px6-4 catalyzes the decarboxylation reaction of lignin monomers and phenolic compounds such as p-coumaric acid, caffeic acid, and ferulic acid into their corresponding 4-vinyl derivatives, that is, 4-vinylphenol, 4-vinylcatechol, and 4-vinylguaiacol, respectively. Among various ferulic acid decarboxylase enzymes, we chose the FADase from Enterobacter sp. Px6-4, whose crystal structure is known, and produced mutants to enhance its catalytic activity by random and site-directed mutagenesis. After three rounds of sequential mutations, FADase(F95L/D112N/V151I) showed approximately 34-fold higher catalytic activity than wild-type for the production of 4-vinylguaiacol from ferulic acid. Docking analyses suggested that the increased activity of FADase(F95L/D112N/V151I) could be due to formation of compact active site compared with that of the wild-type FADase. Considering the amount of phenolic compounds such as lignin monomers in the biomass components, successfully bioengineered FADase(F95L/D112N/V151I) from Enterobacter sp. Px6-4 could provide an ecofriendly biocatalytic tool for producing diverse styrene derivatives from biomass.

Successful Fabrication of GaN Epitaxial Layer on Non-Catalytically grown Graphene

Energy Technology Data Exchange (ETDEWEB)

Hwang, Sung Won [Konkuk University, Chungju (Korea, Republic of); Choi, Suk-Ho [Kyung Hee University, Yongin (Korea, Republic of)

2016-07-15

Sapphire is widely used as a substrate for the growth of GaN epitaxial layer (EPI), but has several drawbacks such as high cost, large lattice mismatch, non-flexibility, and so on. Here, we first employ graphene directly grown on Si or sapphire substrate as a platform for the growth and lift-off of GaN-light-emitting diode (LED) EPI, useful for not only recycling the substrate but also transferring the GaN-LED EPI to other flexible substrates. Sequential standard processes of nucleation/recrystallization of GaN seeds and deposition of undoped (u-) GaN/AlN buffer layer were done on graphene/substrate before the growth of GaN-LED EPI, accompanied by taping and lift-off of u-GaN/AlN or GaN-LED EPI. This approach can overcome the limitations by the catalytic growth and transfer of graphene, and make the oxygen-plasma treatment of graphene for the growth of GaN EPI unnecessary.

Non-Linguistic Vocal Event Detection Using Online Random

DEFF Research Database (Denmark)

Abou-Zleikha, Mohamed; Tan, Zheng-Hua; Christensen, Mads Græsbøll

2014-01-01

areas such as object detection, face recognition, and audio event detection. This paper proposes to use online random forest technique for detecting laughter and filler and for analyzing the importance of various features for non-linguistic vocal event classification through permutation. The results...... show that according to the Area Under Curve measure the online random forest achieved 88.1% compared to 82.9% obtained by the baseline support vector machines for laughter classification and 86.8% to 83.6% for filler classification....

First observations of partially neutralized and quasineutral plasmas in the Columbia Non-neutral Torus

Science.gov (United States)

Sarasola, Xabier; Brenner, Paul; Hahn, Michael; Pedersen, Thomas

2009-11-01

The Columbia Non-neutral Torus (CNT) is the first stellarator devoted to the study of pure electron, partially neutralized and positron-electron plasmas. To date, CNT usually operates with electron rich plasmas (with negligible ion density) [1], but a stellarator can also confine plasmas of arbitrary degree of neutralization. In CNT the accumulation of ions alters the equilibrium of electron plasmas and a global instability has been observed when the ion fraction exceeds 10 %. A characterization of this instability is presented in [2], analyzing its parameter dependence and spatial structure (non- resonant with rational surfaces). A new set of experiments is currently underway studying plasmas of arbitrary degree of neutralization, ranging from pure electron to quasineutral plasmas. Basic observations show that the plasma potential decouples from emitter bias when we increase the degree of the neutralization of our plasmas. Partially neutralized plasmas are also characterized by multiple mode behavior with dominant modes between 20 and 200 kHz. When the plasma becomes quasineutral, it reverts to single mode behavior. The first results on partially neutralized plasmas confined on magnetic surfaces will be presented. [1] J. Kremer, PRL 97, (2006) 095003 [2] Q. Marksteiner, PRL 100 (2008) 065002

Drug use among complete responders, partial responders and non-responders in a longitudinal survey of nonagenarians

DEFF Research Database (Denmark)

Wastesson, Jonas W; Rasmussen, Lotte; Oksuzyan, Anna

2017-01-01

PURPOSE: In observational studies, non-response can limit representativity and introduce bias. We aimed to investigate the longitudinal changes in the number of used drugs among complete responders, partial responders, and non-responders in a whole birth cohort of Danish nonagenarians participati...

Catalytic non-thermal plasma reactor for the decomposition of a ...

Indian Academy of Sciences (India)

2016-08-26

Aug 26, 2016 ... Among the catalytic study, MnOx/SMF (manganese oxide on sintered metal fibres electrode) shows better performance, probably due to the formation of active oxygen species by in situ decomposition of ozone on the catalyst surface. Water vapour further enhanced the performance due to the in situ ...

Randomly and Non-Randomly Missing Renal Function Data in the Strong Heart Study: A Comparison of Imputation Methods.

Directory of Open Access Journals (Sweden)

Nawar Shara

Full Text Available Kidney and cardiovascular disease are widespread among populations with high prevalence of diabetes, such as American Indians participating in the Strong Heart Study (SHS. Studying these conditions simultaneously in longitudinal studies is challenging, because the morbidity and mortality associated with these diseases result in missing data, and these data are likely not missing at random. When such data are merely excluded, study findings may be compromised. In this article, a subset of 2264 participants with complete renal function data from Strong Heart Exams 1 (1989-1991, 2 (1993-1995, and 3 (1998-1999 was used to examine the performance of five methods used to impute missing data: listwise deletion, mean of serial measures, adjacent value, multiple imputation, and pattern-mixture. Three missing at random models and one non-missing at random model were used to compare the performance of the imputation techniques on randomly and non-randomly missing data. The pattern-mixture method was found to perform best for imputing renal function data that were not missing at random. Determining whether data are missing at random or not can help in choosing the imputation method that will provide the most accurate results.

An MGF-based unified framework to determine the joint statistics of partial sums of ordered random variables

KAUST Repository

Nam, Sungsik

2010-11-01

Order statistics find applications in various areas of communications and signal processing. In this paper, we introduce an unified analytical framework to determine the joint statistics of partial sums of ordered random variables (RVs). With the proposed approach, we can systematically derive the joint statistics of any partial sums of ordered statistics, in terms of the moment generating function (MGF) and the probability density function (PDF). Our MGF-based approach applies not only when all the K ordered RVs are involved but also when only the Ks(Ks < K) best RVs are considered. In addition, we present the closed-form expressions for the exponential RV special case. These results apply to the performance analysis of various wireless communication systems over fading channels. © 2006 IEEE.

A comparison of numerical solutions of partial differential equations with probabilistic and possibilistic parameters for the quantification of uncertainty in subsurface solute transport.

Science.gov (United States)

Zhang, Kejiang; Achari, Gopal; Li, Hua

2009-11-03

Traditionally, uncertainty in parameters are represented as probabilistic distributions and incorporated into groundwater flow and contaminant transport models. With the advent of newer uncertainty theories, it is now understood that stochastic methods cannot properly represent non random uncertainties. In the groundwater flow and contaminant transport equations, uncertainty in some parameters may be random, whereas those of others may be non random. The objective of this paper is to develop a fuzzy-stochastic partial differential equation (FSPDE) model to simulate conditions where both random and non random uncertainties are involved in groundwater flow and solute transport. Three potential solution techniques namely, (a) transforming a probability distribution to a possibility distribution (Method I) then a FSPDE becomes a fuzzy partial differential equation (FPDE), (b) transforming a possibility distribution to a probability distribution (Method II) and then a FSPDE becomes a stochastic partial differential equation (SPDE), and (c) the combination of Monte Carlo methods and FPDE solution techniques (Method III) are proposed and compared. The effects of these three methods on the predictive results are investigated by using two case studies. The results show that the predictions obtained from Method II is a specific case of that got from Method I. When an exact probabilistic result is needed, Method II is suggested. As the loss or gain of information during a probability-possibility (or vice versa) transformation cannot be quantified, their influences on the predictive results is not known. Thus, Method III should probably be preferred for risk assessments.

Fractional Multistage Hydrothermal Liquefaction of Biomass and Catalytic Conversion into Hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Cortright, Randy [Virent, Inc., Madison, WI (United States); Rozmiarek, Robert [Virent, Inc., Madison, WI (United States); Dally, Brice [Virent, Inc., Madison, WI (United States); Holland, Chris [Virent, Inc., Madison, WI (United States)

2017-08-31

The objective of this project was to develop an improved multistage process for the hydrothermal liquefaction (HTL) of biomass to serve as a new front-end, deconstruction process ideally suited to feed Virent’s well-proven catalytic technology, which is already being scaled up. This process produced water soluble, partially de-oxygenated intermediates that are ideally suited for catalytic finishing to fungible distillate hydrocarbons. Through this project, Virent, with its partners, demonstrated the conversion of pine wood chips to drop-in hydrocarbon distillate fuels using a multi-stage fractional conversion system that is integrated with Virent’s BioForming® process. The majority of work was in the liquefaction task and included temperature scoping, solvent optimization, and separations.

Catalytic non-thermal plasma reactor for the decomposition of a ...

Indian Academy of Sciences (India)

diseases), hence has a negative impact on the environ- ment.1–4 Some of the well-established technologies for. VOC abatement are thermal and catalytic ... motor driven syringe pump and mixed with ambient air. (300 ml/min at STP) in a mixing chamber. Air flow was regulated by pre-calibrated mass flow controllers.

Random surfaces: A non-perturbative regularization of strings?

International Nuclear Information System (INIS)

Ambjoern, J.

1989-12-01

I review the basic properties of the theory of randum surfaces. While it is by now well known that the theory of (discretized) random surfaces correctly describes the (perturbative) aspects of non-critical strings in d 1. In these lectures I intend to show that the theory of dynamical triangulated random surfaces provides us with a lot of information about the dynamics of both the bosonic string and the superstring even for d>1. I also briefly review recent attempts to define a string field theory (sum over all genus) in this approach. (orig.)

Partial wave expansions for arbitrary spin and the role of non-central forces

International Nuclear Information System (INIS)

Johnson, R.C.

1977-01-01

The partial wave expansion of the amplitudes used by Hooton and Johnson for the scattering of particles of arbitrary spin is derived. A discussion is given of the extent to which effects arising from transition matrix elements that are diagonal and non-diagonal in orbital angular momentum can be distinguished in observables. (Auth.)

Development and test of a new catalytic converter for natural gas ...

Indian Academy of Sciences (India)

catalytic converter and a new natural gas engine such as compressed natural gas. (CNG) direct ..... bility to store oxygen from random gas flow within the substrate in comparison to flow through ..... and behaviour in the water–gas shift reaction.

Bimetallic Nanoparticles in Alternative Solvents for Catalytic Purposes

Directory of Open Access Journals (Sweden)

Trung Dang-Bao

2017-07-01

Full Text Available Bimetallic nanoparticles represent attractive catalytic systems thanks to the synergy between both partners at the atomic level, mainly induced by electronic effects which in turn are associated with the corresponding structures (alloy, core-shell, hetero-dimer. This type of engineered material can trigger changes in the kinetics of catalyzed processes by variations on the electrophilicity/nucleophilicity of the metal centers involved and also promote cooperative effects to foster organic transformations, including multi-component and multi-step processes. Solvents become a crucial factor in the conception of catalytic processes, not only due to their environmental impact, but also because they can preserve the bimetallic structure during the catalytic reaction and therefore increase the catalyst life-time. In this frame, the present review focuses on the recent works described in the literature concerning the synthesis of bimetallic nanoparticles in non-conventional solvents, i.e., other than common volatile compounds, for catalytic applications.

Sharp lower bounds on the extractable randomness from non-uniform sources

NARCIS (Netherlands)

Skoric, B.; Obi, C.; Verbitskiy, E.A.; Schoenmakers, B.

2011-01-01

Extraction of uniform randomness from (noisy) non-uniform sources is an important primitive in many security applications, e.g. (pseudo-)random number generators, privacy-preserving biometrics, and key storage based on Physical Unclonable Functions. Generic extraction methods exist, using universal

Exposure to ultrafine particles in hospitality venues with partial smoking bans.

Science.gov (United States)

Neuberger, Manfred; Moshammer, Hanns; Schietz, Armin

2013-01-01

Fine particles in hospitality venues with insufficient smoking bans indicate health risks from passive smoking. In a random sample of Viennese inns (restaurants, cafes, bars, pubs and discotheques) effects of partial smoking bans on indoor air quality were examined by measurement of count, size and chargeable surface of ultrafine particles (UFPs) sized 10-300 nm, simultaneously with mass of particles sized 300-2500 nm (PM2.5). Air samples were taken in 134 rooms unannounced during busy hours and analyzed by a diffusion size classifier and an optical particle counter. Highest number concentrations of particles were found in smoking venues and smoking rooms (median 66,011 pt/cm(3)). Even non-smoking rooms adjacent to smoking rooms were highly contaminated (median 25,973 pt/cm(3)), compared with non-smoking venues (median 7408 pt/cm(3)). The particle number concentration was significantly correlated with the fine particle mass (Phospitality premises. Health protection of non-smoking guests and employees from risky UFP concentration is insufficient, even in rooms labeled "non-smoking". Partial smoking bans with separation of smoking rooms failed.

Production of filamentous carbon and H{sub 2} by solarthermal catalytic cracking of CH{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Kirillov, V; Kuvshinov, G [Boreskov Inst. of Catalysis (Russian Federation); Reller, A [Hamburg Univ., Hamburg (Germany); Steinfeld, A [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

1997-06-01

The catalytic thermal decomposition of methane has been experimentally studied using high-temperature solar process heat. Nickel catalyst particles, fluidized in methane, were directly irradiated at the PSI solar furnace. Carbon deposition consisted of randomly interlaced filaments that grew as fibers and hollow nanotubes (of approx. 30 nm diameter) originating at each catalytic particle. (author) 4 figs., 7 refs.

Electronic states of carbon alloy catalysts and nitrogen substituent effects on catalytic activity

Science.gov (United States)

Hata, Tomoyuki; Ushiyama, Hiroshi; Yamashita, Koichi

2013-03-01

In recent years, Carbon Alloy Catalysts (CACs) are attracting attention as a candidate for non-platinum-based cathode catalysts in fuel cells. Oxygen reduction reactions at the cathode are divided into two elementary processes, electron transfer and oxygen adsorption. The electron transfer reaction is the rate-determining, and by comparison of energy levels, catalytic activity can be evaluated quantitatively. On the other hand, to begin with, adsorption mechanism is obscure. The purpose of this study is to understand the effect of nitrogen substitution and oxygen adsorption mechanism, by first-principle electronic structure calculations for nitrogen substituted models. To reproduce the elementary processes of oxygen adsorption, we assumed that the initial structures are formed based on the Pauling model, a CACs model and nitrogen substituted CACs models in which various points are replaced with nitrogen. When we try to focus only on the DOS peaks of oxygen, in some substituted model that has high adsorption activity, a characteristic partial occupancy state was found. We conclude that this state will affect the adsorption activity, and discuss on why partially occupied states appear with simplification by using an orbital correlation diagram.

Catalytical Properties of Free and Immobilized Aspergillus niger Tannase

Directory of Open Access Journals (Sweden)

Abril Flores-Maltos

2011-01-01

Full Text Available A fungal tannase was produced, recovered, and immobilized by entrapment in calcium alginate beads. Catalytical properties of the immobilized enzyme were compared with those of the free one. Tannase was produced intracellularly by the xerophilic fungus Aspergillus niger GH1 in a submerged fermentation system. Enzyme was recovered by cell disruption and the crude extract was partially purified. The catalytical properties of free and immobilized tannase were evaluated using tannic acid and methyl gallate as substrates. KM and Vmax values for free enzyme were very similar for both substrates. But, after immobilization, KM and Vmax values increased drastically using tannic acid as substrate. These results indicated that immobilized tannase is a better biocatalyst than free enzyme for applications on liquid systems with high tannin content, such as bioremediation of tannery or olive-mill wastewater.

Catalytical Properties of Free and Immobilized Aspergillus niger Tannase.

Science.gov (United States)

Flores-Maltos, Abril; Rodríguez-Durán, Luis V; Renovato, Jacqueline; Contreras, Juan C; Rodríguez, Raúl; Aguilar, Cristóbal N

2011-01-01

A fungal tannase was produced, recovered, and immobilized by entrapment in calcium alginate beads. Catalytical properties of the immobilized enzyme were compared with those of the free one. Tannase was produced intracellularly by the xerophilic fungus Aspergillus niger GH1 in a submerged fermentation system. Enzyme was recovered by cell disruption and the crude extract was partially purified. The catalytical properties of free and immobilized tannase were evaluated using tannic acid and methyl gallate as substrates. K(M) and V(max) values for free enzyme were very similar for both substrates. But, after immobilization, K(M) and V(max) values increased drastically using tannic acid as substrate. These results indicated that immobilized tannase is a better biocatalyst than free enzyme for applications on liquid systems with high tannin content, such as bioremediation of tannery or olive-mill wastewater.

Quasi-stability of a vector trajectorial problem with non-linear partial criteria

Directory of Open Access Journals (Sweden)

Vladimir A. Emelichev

2003-10-01

Full Text Available Multi-objective (vector combinatorial problem of finding the Pareto set with four kinds of non-linear partial criteria is considered. Necessary and sufficient conditions of that kind of stability of the problem (quasi-stability are obtained. The problem is a discrete analogue of the lower semicontinuity by Hausdorff of the optimal mapping. Mathematics Subject Classification 2000: 90C10, 90C05, 90C29, 90C31.

Correction of confounding bias in non-randomized studies by appropriate weighting.

Science.gov (United States)

Schmoor, Claudia; Gall, Christine; Stampf, Susanne; Graf, Erika

2011-03-01

In non-randomized studies, the assessment of a causal effect of treatment or exposure on outcome is hampered by possible confounding. Applying multiple regression models including the effects of treatment and covariates on outcome is the well-known classical approach to adjust for confounding. In recent years other approaches have been promoted. One of them is based on the propensity score and considers the effect of possible confounders on treatment as a relevant criterion for adjustment. Another proposal is based on using an instrumental variable. Here inference relies on a factor, the instrument, which affects treatment but is thought to be otherwise unrelated to outcome, so that it mimics randomization. Each of these approaches can basically be interpreted as a simple reweighting scheme, designed to address confounding. The procedures will be compared with respect to their fundamental properties, namely, which bias they aim to eliminate, which effect they aim to estimate, and which parameter is modelled. We will expand our overview of methods for analysis of non-randomized studies to methods for analysis of randomized controlled trials and show that analyses of both study types may target different effects and different parameters. The considerations will be illustrated using a breast cancer study with a so-called Comprehensive Cohort Study design, including a randomized controlled trial and a non-randomized study in the same patient population as sub-cohorts. This design offers ideal opportunities to discuss and illustrate the properties of the different approaches. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Environmental and economic evaluation of selective non-catalytic reduction of nitrogen oxides

Science.gov (United States)

Parchevskii, V. M.; Shchederkina, T. E.; Proshina, A. O.

2017-11-01

There are two groups of atmosphere protecting measures: technology (primary) and treatment (secondary). When burning high-calorie low-volatile brands of coals in the furnaces with liquid slag removal to achieve emission standards required joint use of these two methods, for example, staged combustion and selective non-catalytic reduction recovery (SNCR). For the economically intelligent combination of these two methods it is necessary to have information not only about the environmental performance of each method, but also the operating costs per unit of reduced emission. The authors of this report are made an environmental-economic analysis of SNCR on boiler Π-50P Kashirskaya power station. The obtained results about the dependence of costs from the load of the boiler and the mass emissions of nitrogen oxides then approximates into empirical formulas, is named as environmental and economic characteristics, which is suitable for downloading into controllers and other control devices for subsequent implementation of optimal control of emissions to ensure compliance with environmental regulations at the lowest cost at any load of the boiler.

Catalytic ring-​opening copolymerization of limonene oxide and phthalic anhydride : toward partially renewable polyesters

NARCIS (Netherlands)

Hosseini Nejad, E.; Pionasari, A; Melis, van C.G.W.; Koning, C.E.; Duchateau, R.

2013-01-01

Catalytic ring-¿opening copolymn. of limonene oxide with phthalic anhydride was performed applying metal t-¿Bu-¿salophen complexes (t-¿Bu-¿salophen)¿MX; M = Cr, X = Cl (1)¿, M = Al, X = Cl (2)¿, M = Co, X = OAc (3)¿, M = Mn, X = Cl (4)¿, t-¿Bu-¿salophen =

On evolving deformation microstructures in non-convex partially damaged solids

KAUST Repository

Gurses, Ercan

2011-06-01

The paper outlines a relaxation method based on a particular isotropic microstructure evolution and applies it to the model problem of rate independent, partially damaged solids. The method uses an incremental variational formulation for standard dissipative materials. In an incremental setting at finite time steps, the formulation defines a quasi-hyperelastic stress potential. The existence of this potential allows a typical incremental boundary value problem of damage mechanics to be expressed in terms of a principle of minimum incremental work. Mathematical existence theorems of minimizers then induce a definition of the material stability in terms of the sequential weak lower semicontinuity of the incremental functional. As a consequence, the incremental material stability of standard dissipative solids may be defined in terms of weak convexity notions of the stress potential. Furthermore, the variational setting opens up the possibility to analyze the development of deformation microstructures in the post-critical range of unstable inelastic materials based on energy relaxation methods. In partially damaged solids, accumulated damage may yield non-convex stress potentials which indicate instability and formation of fine-scale microstructures. These microstructures can be resolved by use of relaxation techniques associated with the construction of convex hulls. We propose a particular relaxation method for partially damaged solids and investigate it in one- and multi-dimensional settings. To this end, we introduce a new isotropic microstructure which provides a simple approximation of the multi-dimensional rank-one convex hull. The development of those isotropic microstructures is investigated for homogeneous and inhomogeneous numerical simulations. © 2011 Elsevier Ltd. All rights reserved.

A reverse flow catalytic membrane reactor for the production of syngas: an experimental study

NARCIS (Netherlands)

Smit, J.; Bekink, G.J.; van Sint Annaland, M.; Kuipers, J.A.M.

2005-01-01

In this paper experimental results are presented for a demonstration unit of a recently proposed novel integrated reactor concept (Smit et. al., 2005) for the partial oxidation of natural gas to syngas (POM), namely a Reverse Flow Catalytic Membrane Reactor (RFCMR). Natural gas has great potential

Partial nitrification of non-ammonium-rich wastewater within biofilm filters under ambient temperature.

Science.gov (United States)

Wang, Hongyu; He, Jiajie; Yang, Kai

2010-01-01

This study evaluated the partial nitrification performances of two biofilm filters over a synthetic non-ammonium-rich wastewater at a 20°C room temperature under both limited DO (∼2.0 mg/L) and unlimited DO (∼4.0 mg/L) conditions. The two filters were each of 80 cm long and used different biofilm carriers: activated carbon and ceramic granule. Results showed that partial nitrification was accomplished for both filters under the limited DO condition. However, the effluent NO(2)-N was higher in the ceramic granule filter than in the activated carbon filter, and was less susceptible to the influent COD/N changes. Further investigation into the water phase COD and NH(4)-N depth profiles and bacteria population within the two filters showed that by putting upper filter layer (upstream) to confront relatively higher influent COD/N ratios, the filtration process naturally put lower filter layers (downstream) relatively more favorable for nitrifying bacteria (ammonia oxidizing bacteria in this study) to prosper, making the filter depth left for nitrification a crucial factor for the effectiveness of nitrification with a filter. The potentially different porous flow velocities of the two filters might be the reason to cause their different partial nitrification performances, with a lower porous flow velocity (the ceramic granule filter) favoring partial nitrification more. In summation, DO, filter depth, and filtration speed should be played together to successfully operate a biofilm filter for partial nitrification.

Partial synchronization in networks of non-linearly coupled oscillators: The Deserter Hubs Model

Energy Technology Data Exchange (ETDEWEB)

Freitas, Celso, E-mail: cbnfreitas@gmail.com; Macau, Elbert, E-mail: elbert.macau@inpe.br [Associate Laboratory for Computing and Applied Mathematics - LAC, Brazilian National Institute for Space Research - INPE (Brazil); Pikovsky, Arkady, E-mail: pikovsky@uni-potsdam.de [Department of Physics and Astronomy, University of Potsdam, Germany and Department of Control Theory, Nizhni Novgorod State University, Gagarin Av. 23, 606950, Nizhni Novgorod (Russian Federation)

2015-04-15

We study the Deserter Hubs Model: a Kuramoto-like model of coupled identical phase oscillators on a network, where attractive and repulsive couplings are balanced dynamically due to nonlinearity of interactions. Under weak force, an oscillator tends to follow the phase of its neighbors, but if an oscillator is compelled to follow its peers by a sufficient large number of cohesive neighbors, then it actually starts to act in the opposite manner, i.e., in anti-phase with the majority. Analytic results yield that if the repulsion parameter is small enough in comparison with the degree of the maximum hub, then the full synchronization state is locally stable. Numerical experiments are performed to explore the model beyond this threshold, where the overall cohesion is lost. We report in detail partially synchronous dynamical regimes, like stationary phase-locking, multistability, periodic and chaotic states. Via statistical analysis of different network organizations like tree, scale-free, and random ones, we found a measure allowing one to predict relative abundance of partially synchronous stationary states in comparison to time-dependent ones.

High Dimensional Spectral Graph Theory and Non-backtracking Random Walks on Graphs

Science.gov (United States)

Kempton, Mark

This thesis has two primary areas of focus. First we study connection graphs, which are weighted graphs in which each edge is associated with a d-dimensional rotation matrix for some fixed dimension d, in addition to a scalar weight. Second, we study non-backtracking random walks on graphs, which are random walks with the additional constraint that they cannot return to the immediately previous state at any given step. Our work in connection graphs is centered on the notion of consistency, that is, the product of rotations moving from one vertex to another is independent of the path taken, and a generalization called epsilon-consistency. We present higher dimensional versions of the combinatorial Laplacian matrix and normalized Laplacian matrix from spectral graph theory, and give results characterizing the consistency of a connection graph in terms of the spectra of these matrices. We generalize several tools from classical spectral graph theory, such as PageRank and effective resistance, to apply to connection graphs. We use these tools to give algorithms for sparsification, clustering, and noise reduction on connection graphs. In non-backtracking random walks, we address the question raised by Alon et. al. concerning how the mixing rate of a non-backtracking random walk to its stationary distribution compares to the mixing rate for an ordinary random walk. Alon et. al. address this question for regular graphs. We take a different approach, and use a generalization of Ihara's Theorem to give a new proof of Alon's result for regular graphs, and to extend the result to biregular graphs. Finally, we give a non-backtracking version of Polya's Random Walk Theorem for 2-dimensional grids.

Non-isothermal synergetic catalytic effect of TiF{sub 3} and Nb{sub 2}O{sub 5} on dehydrogenation high-energy ball milled MgH{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Zhang, Tiebang, E-mail: tiebangzhang@nwpu.edu.cn; Hou, Xiaojiang; Hu, Rui; Kou, Hongchao; Li, Jinshan

2016-11-01

MgH{sub 2}-M (M = TiF{sub 3} or Nb{sub 2}O{sub 5} or both of them) composites prepared by high-energy ball milling are used in this work to illustrate the dehydrogenation behavior of MgH{sub 2} with the addition of catalysts. The phase compositions, microstructures, particle morphologies and distributions of MgH{sub 2} with catalysts have been evaluated. The non-isothermal synergetic catalytic-dehydrogenation effect of TiF{sub 3} and Nb{sub 2}O{sub 5} evaluated by differential scanning calorimetry gives the evidences that the addition of catalysts is an effective strategy to destabilize MgH{sub 2} and reduce hydrogen desorption temperatures and activation energies. Depending on additives, the desorption peak temperatures of catalyzed MgH{sub 2} reduce from 417 °C to 341 °C for TiF{sub 3} and from 417 °C to 336 °C for Nb{sub 2}O{sub 5}, respectively. The desorption peak temperature reaches as low as 310 °C for MgH{sub 2} catalyzed by TiF{sub 3} coupling with Nb{sub 2}O{sub 5}. The non-isothermal synergetic catalytic effect of TiF{sub 3} and Nb{sub 2}O{sub 5} is mainly attributed to electronic exchange reactions with hydrogen molecules, which improve the recombination of hydrogen atoms during dehydrogenation process of MgH{sub 2}. - Highlights: • Catalytic surface for MgH{sub 2} is achieved by high-energy ball milling. • Non-isothermal dehydrogenation behavior of MgH{sub 2} with TiF{sub 3} and/or Nb{sub 2}O{sub 5} is illustrated. • Dehydrogenation activation energies of synergetic catalyzed MgH{sub 2} are obtained. • Synergetic catalytic-dehydrogenation mechanism of TiF{sub 3} and Nb{sub 2}O{sub 5} is proposed.

Additive non-uniform random sampling in superimposed fiber Bragg grating strain gauge

Science.gov (United States)

Ma, Y. C.; Liu, H. Y.; Yan, S. B.; Yang, Y. H.; Yang, M. W.; Li, J. M.; Tang, J.

2013-05-01

This paper demonstrates an additive non-uniform random sampling and interrogation method for dynamic and/or static strain gauge using a reflection spectrum from two superimposed fiber Bragg gratings (FBGs). The superimposed FBGs are designed to generate non-equidistant space of a sensing pulse train in the time domain during dynamic strain gauge. By combining centroid finding with smooth filtering methods, both the interrogation speed and accuracy are improved. A 1.9 kHz dynamic strain is measured by generating an additive non-uniform randomly distributed 2 kHz optical sensing pulse train from a mean 500 Hz triangular periodically changing scanning frequency.

Randomized clinical trial of 270° posterior versus 180° anterior partial laparoscopic fundoplication for gastro-oesophageal reflux disease.

Science.gov (United States)

Roks, D J; Koetje, J H; Oor, J E; Broeders, J A; Nieuwenhuijs, V B; Hazebroek, E J

2017-06-01

Partial fundoplications provide similar reflux control with fewer post-fundoplication symptoms compared with Nissen fundoplication for gastro-oesophageal reflux disease (GORD). The best choice of procedure for partial fundoplication remains unclear. The aim of this study was to compare the outcome of two different types of partial fundoplication for GORD. A double-blind RCT was conducted between 2012 and 2015 in two hospitals specializing in antireflux surgery. Patients were randomized to undergo either a laparoscopic 270° posterior fundoplication (Toupet) or a laparoscopic 180° anterior fundoplication. The primary outcome was postoperative dysphagia at 12 months, measured by the Dakkak score. Subjective outcome was analysed at 1, 3, 6 and 12 months after surgery. Objective reflux control was assessed before and 6 months after surgery. Ninety-four patients were randomized to laparoscopic Toupet or laparoscopic 180° anterior fundoplication (47 in each group). At 12 months, 85 patients (90 per cent) were available for follow-up. Objective scores were available for 76 (81 per cent). Postoperative Dakkak dysphagia score at 12 months was similar in the two groups (mean 5·9 for Toupet versus 6·4 for anterior fundoplication; P = 0·773). Subjective outcome at 12 months demonstrated no significant differences in control of reflux or post-fundoplication symptoms. Overall satisfaction and willingness to undergo surgery did not differ between the groups. Postoperative endoscopy and 24-h pH monitoring showed no significant differences in mean oesophageal acid exposure time or recurrent pathological oesophageal acid exposure. Both types of partial fundoplication provided similar control of GORD at 12 months, with no difference in post-fundoplication symptoms. Registration number: NTR5702 (www.trialregister.nl). © 2017 BJS Society Ltd Published by John Wiley & Sons Ltd.

Preparation of a non-woven poly(ε-caprolactone) fabric with partially embedded apatite surface for bone tissue engineering applications by partial surface melting of poly(ε-caprolactone) fibers.

Science.gov (United States)

Kim, In Ae; Rhee, Sang-Hoon

2017-07-01

This article describes a novel method for the preparation of a biodegradable non-woven poly(ε-caprolactone) fabric with a partially embedded apatite surface designed for application as a scaffold material for bone tissue engineering. The non-woven poly(ε-caprolactone) fabric was generated by the electro-spinning technique and then apatite was coated in simulated body fluid after coating the PVA solution containing CaCl 2 ·2H 2 O. The apatite crystals were partially embedded or fully embedded into the thermoplastic poly(ε-caprolactone) fibers by controlling the degree of poly(ε-caprolactone) fiber surface melting in a convection oven. Identical apatite-coated poly(ε-caprolactone) fabric that did not undergo heat-treatment was used as a control. The features of the embedded apatite crystals were evaluated by FE-SEM, AFM, EDS, and XRD. The adhesion strengths of the coated apatite layers and the tensile strengths of the apatite coated fabrics with and without heat-treatment were assessed by the tape-test and a universal testing machine, respectively. The degree of water absorbance was assessed by adding a DMEM droplet onto the fabrics. Moreover, cell penetrability was assessed by seeding preosteoblastic MC3T3-E1 cells onto the fabrics and observing the degrees of cell penetration after 1 and 4 weeks by staining nuclei with DAPI. The non-woven poly(ε-caprolactone) fabric with a partially embedded apatite surface showed good water absorbance, cell penetrability, higher apatite adhesion strength, and higher tensile strength compared with the control fabric. These results show that the non-woven poly(ε-caprolactone) fabric with a partially embedded apatite surface is a potential candidate scaffold for bone tissue engineering due to its strong apatite adhesion strength and excellent cell penetrability. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 105A: 1973-1983, 2017. © 2017 Wiley Periodicals, Inc.

Influence of Partial Neutralization on Catalytic Activity of Ion Exchange Resin

Czech Academy of Sciences Publication Activity Database

Holub, Ladislav; Jeřábek, Karel

2005-01-01

Roč. 231, 1-2 (2005), s. 21-26 ISSN 1381-1169 R&D Projects: GA ČR(CZ) GA104/02/1104 Institutional research plan: CEZ:AV0Z40720504 Keywords : catalysis * partial neutralization * polymer supports Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 2.348, year: 2005

Crystal structure of a catalytically active, non-toxic endopeptidase derivative of Clostridium botulinum toxin A.

Science.gov (United States)

Masuyer, Geoffrey; Thiyagarajan, Nethaji; James, Peter L; Marks, Philip M H; Chaddock, John A; Acharya, K Ravi

2009-03-27

Botulinum neurotoxins (BoNTs) modulate cholinergic nerve terminals to result in neurotransmitter blockade. BoNTs consists of catalytic (LC), translocation (Hn) and cell-binding domains (Hc). The binding function of the Hc domain is essential for BoNTs to bind the neuronal cell membrane, therefore, removal of the Hc domain results in a product that retains the endopeptidase activity of the LC but is non-toxic. Thus, a molecule consisting of LC and Hn domains of BoNTs, termed LHn, is a suitable molecule for engineering novel therapeutics. The structure of LHA at 2.6 A reported here provides an understanding of the structural implications and challenges of engineering therapeutic molecules that combine functional properties of LHn of BoNTs with specific ligand partners to target different cell types.

A new surface catalytic model for silica-based thermal protection material for hypersonic vehicles

Directory of Open Access Journals (Sweden)

Li Kai

2015-10-01

Full Text Available Silica-based materials are widely employed in the thermal protection system for hypersonic vehicles, and the investigation of their catalytic characteristics is crucially important for accurate aerothermal heating prediction. By analyzing the disadvantages of Norman’s high and low temperature models, this paper combines the two models and proposes an eight-reaction combined surface catalytic model to describe the catalysis between oxygen and silica surface. Given proper evaluation of the parameters according to many references, the recombination coefficient obtained shows good agreement with experimental data. The catalytic mechanisms between oxygen and silica surface are then analyzed. Results show that with the increase of the wall temperature, the dominant reaction contributing to catalytic coefficient varies from Langmuir–Hinshelwood (LH recombination (TW  1350 K. The surface coverage of chemisorption areas varies evidently with the dominant reactions in the high temperature (HT range, while the surface coverage of physisorption areas varies within quite low temperature (LT range (TW < 250 K. Recommended evaluation of partial parameters is also given.

Recovery of homogeneous polyoxometallate catalysts from aqueous and organic media by a mesoporous ceramic membrane without loss of catalytic activity.

Science.gov (United States)

Roy Chowdhury, Sankhanilay; Witte, Peter T; Blank, Dave H A; Alsters, Paul L; Ten Elshof, Johan E

2006-04-03

The recovery of homogeneous polyoxometallate (POM) oxidation catalysts from aqueous and non-aqueous media by a nanofiltration process using mesoporous gamma-alumina membranes is reported. The recovery of Q(12)[WZn(3)(ZnW(9)O(34))(2)] (Q=[MeN(n-C(8)H(17))(3)](+)) from toluene-based media was quantitative within experimental error, while up to 97 % of Na(12)[WZn(3)(ZnW(9)O(34))(2)] could be recovered from water. The toluene-soluble POM catalyst was used repeatedly in the conversion of cyclooctene to cyclooctene oxide and separated from the product mixture after each reaction. The catalytic activity increased steadily with the number of times that the catalyst had been recycled, which was attributed to partial removal of the excess QCl that is known to have a negative influence on the catalytic activity. Differences in the permeability of the membrane for different liquid media can be attributed to viscosity differences and/or capillary condensation effects. The influence of membrane pore radius on permeability and recovery is discussed.

A polygeneration from a dual-gas partial catalytic oxidation coupling with an oxygen-permeable membrane reactor

International Nuclear Information System (INIS)

Hao, Yanhong; Huang, Yi; Gong, Minhui; Li, Wenying; Feng, Jie; Yi, Qun

2015-01-01

Highlights: • A new polygeneration system (PL-PCO-OPMR) to DME/methanol/power is proposed. • Exergeo-economic analysis is adopted to disclose the performance of systems. • Key technological conditions and parameters for PL-PCO-OPMR are optimized. • PL-PCO-OPMR shows high energy efficiency and low CO_2 emission. • PL-PCO-OPMR is an attractive way for high efficient and clean use of COG and CGG. - Abstract: Polygeneration system, typically involving chemicals/fuels and electricity co-production, is a promising technology for the sustainable development of energy and environment. In this study, a new polygeneration system based on coal and coke oven gas (COG) inputs for co-production of dimethyl ether (DME)/methanol and electricity is proposed. In the new system, an appropriate syngas for the synthesis of DME is from coal gasified gas (CGG) reforming of COG coupled with an oxygen-permeable membrane reactor, in which both COG and CGG reforming process and fuel combustion process are incorporated, which reduces exergy destruction in the whole reforming process. In order to obtain the best performance of CO_2 reduction, energy saving and economic benefit, the key operation parameters of the proposed process are analyzed and optimized. The new system is compared with the process based on CH_4/CO_2 dry reforming, in terms of exergy efficiency, exergy cost and CO_2 emissions. Through the new system, the exergy efficiency can be increased by 7.8%, the exergy cost can be reduced by 0.88 USD/GJ and the CO_2 emission can be reduced by 0.023 kg/MJ. These results suggest that the polygeneration system from CGG and COG partial catalytic oxidation coupling with an oxygen-permeable membrane reactor (PL-PCO-OPMR) would be a more attractive way for highly efficient and clean use of CGG and COG.

Effect of NO2 and water on the catalytic oxidation of soot

DEFF Research Database (Denmark)

Christensen, Jakob Munkholt; Grunwaldt, Jan-Dierk; Jensen, Anker Degn

2017-01-01

The influence of adding NO2 to 10 vol% O2/N2 on non-catalytic soot oxidation and soot oxidation in intimate or loose contact with a catalyst has been investigated. In non-catalytic soot oxidation the oxidation rate is increased significantly at lower temperatures by NO2. For soot oxidation in tig...... exhibited a volcano-curve dependence on the heat of oxygen chemisorption, and among the tested pure metals and oxides Cr2O3 was the most active catalyst. Further improvements were achieved with a FeaCrbOx binary oxide catalyst....

HYBRID SELECTIVE NON-CATALYTIC REDUCTION (SNCR)/SELECTIVE CATALYTIC REDUCTION (SCR) DEMONSTRATION FOR THE REMOVAL OF NOx FROM BOILER FLUE GASES

Energy Technology Data Exchange (ETDEWEB)

Jerry B. Urbas

1999-05-01

The U. S. Department of Energy (DOE), Electric Power Research Institute (EPRI), Pennsylvania Electric Energy Research Council, (PEERC), New York State Electric and Gas and GPU Generation, Inc. jointly funded a demonstration to determine the capabilities for Hybrid SNCR/SCR (Selective Non-Catalytic Reduction/Selective Catalytic Reduction) technology. The demonstration site was GPU Generation's Seward Unit No.5 (147MW) located in Seward Pennsylvania. The demonstration began in October of 1997 and ended in December 1998. DOE funding was provided through Grant No. DE-FG22-96PC96256 with T. J. Feeley as the Project Manager. EPRI funding was provided through agreements TC4599-001-26999 and TC4599-002-26999 with E. Hughes as the Project Manager. This project demonstrated the operation of the Hybrid SNCR/SCR NO{sub x} control process on a full-scale coal fired utility boiler. The hybrid technology was expected to provide a cost-effective method of reducing NO{sub x} while balancing capital and operation costs. An existing urea based SNCR system was modified with an expanded-duct catalyst to provide increased NO{sub x} reduction efficiency from the SNCR while producing increased ammonia slip levels to the catalyst. The catalyst was sized to reduce the ammonia slip to the air heaters to less than 2 ppm while providing equivalent NO{sub x} reductions. The project goals were to demonstrate hybrid technology is capable of achieving at least a 55% reduction in NO{sub x} emissions while maintaining less than 2ppm ammonia slip to the air heaters, maintain flyash marketability, verify the cost benefit and applicability of Hybrid post combustion technology, and reduce forced outages due to ammonium bisulfate (ABS) fouling of the air heaters. Early system limitations, due to gas temperature stratification, restricted the Hybrid NO{sub x} reduction capabilities to 48% with an ammonia slip of 6.1 mg/Nm{sup 3} (8 ppm) at the catalyst inlet. After resolving the stratification

Catalytic reduction of NO by methane using a Pt/C/polybenzimidazole/Pt/C fuel cell

DEFF Research Database (Denmark)

Petrushina, Irina; Cleemann, Lars Nilausen; Refshauge, Rasmus

2007-01-01

with participation of H+ or electrochemically produced hydrogen. When added, methane partially suppresses the electrochemical reduction of NO. Methane outlet concentration monitoring has shown the CH4 participation in the chemical catalytic reduction, i.e., methane co-adsorption with NO inhibited the electrochemical...... NO reduction and introduced a dominant chemical path of the NO reduction. The products of the NO reduction with methane were N2, C2H4, and water. The catalytic NO reduction by methane was promoted when the catalyst was negatively polarized (−0.2 V). Repeated negative polarization of the catalyst increased...

Additive non-uniform random sampling in superimposed fiber Bragg grating strain gauge

International Nuclear Information System (INIS)

Ma, Y C; Liu, H Y; Yan, S B; Li, J M; Tang, J; Yang, Y H; Yang, M W

2013-01-01

This paper demonstrates an additive non-uniform random sampling and interrogation method for dynamic and/or static strain gauge using a reflection spectrum from two superimposed fiber Bragg gratings (FBGs). The superimposed FBGs are designed to generate non-equidistant space of a sensing pulse train in the time domain during dynamic strain gauge. By combining centroid finding with smooth filtering methods, both the interrogation speed and accuracy are improved. A 1.9 kHz dynamic strain is measured by generating an additive non-uniform randomly distributed 2 kHz optical sensing pulse train from a mean 500 Hz triangular periodically changing scanning frequency. (paper)

Thermogravimetric kinetic modelling of in-situ catalytic pyrolytic conversion of rice husk to bioenergy using rice hull ash catalyst.

Science.gov (United States)

Loy, Adrian Chun Minh; Gan, Darren Kin Wai; Yusup, Suzana; Chin, Bridgid Lai Fui; Lam, Man Kee; Shahbaz, Muhammad; Unrean, Pornkamol; Acda, Menandro N; Rianawati, Elisabeth

2018-04-07

The thermal degradation behaviour and kinetic parameter of non-catalytic and catalytic pyrolysis of rice husk (RH) using rice hull ash (RHA) as catalyst were investigated using thermogravimetric analysis at four different heating rates of 10, 20, 50 and 100 K/min. Four different iso conversional kinetic models such as Kissinger, Friedman, Kissinger-Akahira-Sunose (KAS) and Ozawa-Flynn-Wall (OFW) were applied in this study to calculate the activation energy (E A ) and pre-exponential value (A) of the system. The E A of non-catalytic and catalytic pyrolysis was found to be in the range of 152-190 kJ/mol and 146-153 kJ/mol, respectively. The results showed that the catalytic pyrolysis of RH had resulted in a lower E A as compared to non-catalytic pyrolysis of RH and other biomass in literature. Furthermore, the high Gibb's free energy obtained in RH implied that it has the potential to serve as a source of bioenergy production. Copyright © 2018 Elsevier Ltd. All rights reserved.

Essays on partial retirement

NARCIS (Netherlands)

Kantarci, T.

2012-01-01

The five essays in this dissertation address a range of topics in the micro-economic literature on partial retirement. The focus is on the labor market behavior of older age groups. The essays examine the economic and non-economic determinants of partial retirement behavior, the effect of partial

Optimization of the catalytic converter internal flow by using 3D-CFD; Sanjigen nagare kaiseki ni yoru shokubai converter nai nagare no saitekika

Energy Technology Data Exchange (ETDEWEB)

Toi, M; Sugiura, S [Toyota Motor Corp., Tokyo (Japan)

1997-10-01

By using computational fluid dynamics and statistical quality control method, we investigated the contribution of front and rear catalytic converter cone shape for the pressure loss and the partial flow, also led the optimal terms and the predictional formulations efficiently. According to this, we can investigate the optimal position of the catalytic converter from the planning. 8 figs., 6 tabs.

Surface electronic structure-catalytic activity correlation of partially reduced molybdenum oxide(s) for the isomerization of light alkenes and alkanes

International Nuclear Information System (INIS)

Al-Kandari, S; Al-Kandari, H; Al-Kharafi, F; Katrib, A

2008-01-01

Catalytic activity-surface electronic structure correlation was carried out using surface XPS-UPS techniques. In situ reduction by hydrogen, were carried out at similar experimental conditions to those employed for the catalytic reactions. In the case of MoO 3 deposited on TiO 2 , the reduction to MoO 2 state with the bifunctional MoO 2 (H x ) ac phase on its surface starts at 573 K and reaches a stable state at temperatures between 653-673 K. In the case of alumina support, a strong metal-support interaction takes place during the catalyst preparation, leading to Al 2 (MoO 4 ) 3 complex formation as characterized by XRD. The reduction process(s) of this complex by hydrogen as a function of temperature is different from what is observed in the case of titania support. The changes in the chemical structure of the sample surface in both systems were tested for the catalytic reactions of 1-pentene and n-pentane

Non Catalytic Transesterification of Vegetables Oil to Biodiesel in Sub-and Supercritical Methanol: A Kinetic’s Study

Directory of Open Access Journals (Sweden)

Nyoman Puspa Asri

2013-03-01

Full Text Available Non catalytic transesterification in sub and supercritical methanol have been used to produce biodiesel from palm oil and soybean oil. A kinetic study was done under reaction condition with temperature and time control. The experiments were carried out in a batch type reactor at reaction temperatures from 210 °C (subcritical condition to 290 °C (the supercritical state in the interval ranges of temperature of 20 °C and at various molar ratios of oil to methanol. The rate constants of the reaction were determined by employing a simple method, with the overall chemical reaction followed the pseudo-first–order reaction. Based on the results, the rate constants of vegetables oil were significantly influenced by reaction temperature, which were gradually increased at subcritical temperature, but sharply increased in the supercritical state. However, the rate constants of soybean oil were slightly higher than that of palm oil. The activation energy for transesterification of soybean oil was 89.32 and 79.05 kJ/mole for palm oil. Meanwhile, the frequency factor values of both oils were 72462892 and 391210 min-1, respectively. The rate reaction for both of oil were expressed as -rTG = 72462892 exp(-89.32/RTCTG for soybean oil and -rTG = 391210 exp(-79.05/RTCTG for palm oil. © 2013 BCREC UNDIP. All rights reservedReceived: 18th October 2012; Revised: 14th December 2012; Accepted: 16th December 2012[How to Cite: N.P. Asri, S. Machmudah, W. Wahyudiono, S. Suprapto, K. Budikarjono, A. Roesyadi, M. Goto, (2013. Non Catalytic Transesterification of Vegetables Oil to Biodiesel in Sub-and Supercritical Methanol: A Kinetic’s Study. Bulletin of Chemical Reaction Engineering & Catalysis, 7 (3: 215-223. (doi:10.9767/bcrec.7.3.4060.215-223][Permalink/DOI: http://dx.doi.org/10.9767/bcrec.7.3.4060.215-223 ] View in  |

A space-jump derivation for non-local models of cell-cell adhesion and non-local chemotaxis.

Science.gov (United States)

Buttenschön, Andreas; Hillen, Thomas; Gerisch, Alf; Painter, Kevin J

2018-01-01

Cellular adhesion provides one of the fundamental forms of biological interaction between cells and their surroundings, yet the continuum modelling of cellular adhesion has remained mathematically challenging. In 2006, Armstrong et al. proposed a mathematical model in the form of an integro-partial differential equation. Although successful in applications, a derivation from an underlying stochastic random walk has remained elusive. In this work we develop a framework by which non-local models can be derived from a space-jump process. We show how the notions of motility and a cell polarization vector can be naturally included. With this derivation we are able to include microscopic biological properties into the model. We show that particular choices yield the original Armstrong model, while others lead to more general models, including a doubly non-local adhesion model and non-local chemotaxis models. Finally, we use random walk simulations to confirm that the corresponding continuum model represents the mean field behaviour of the stochastic random walk.

Treadmill training with partial body-weight support after anterior cruciate ligament reconstruction: a randomized controlled trial.

Science.gov (United States)

Luo, Yuan; Shen, Weizhong; Jiang, Zhong; Sha, Jiao

2016-12-01

[Purpose] To compare the effects of treadmill training with partial body weight support (TTPBWS) and conventional physical therapy (PT) on subjects with anterior cruciate ligament reconstructions. [Subjects and Methods] A total of 40 subjects were randomly allocated to either a treatment group or a control group. Subjects received either treadmill training with partial body weight support (treatment group) or conventional physical therapy (control group). The circumferences of the lower extremities, Holden classifications, 10-meter walking times and the International Knee Documentation Committee (IKDC) scores were compared at 12 and 24 weeks post-operation. The knee joint stability was tested at 24 weeks post-operation using a KT-1000. [Results] Significant differences were found between the two groups at the 12 weeks post-operation. For most of the measures, there was no significant difference between the groups at 24 weeks post-operation. Interestingly, for most of the measures, there was no significant difference between their values in the treatment group at 12 weeks and their values in the control group at 24 weeks post-operation. [Conclusion] The function of a subject's lower extremities can be improved and the improvement was clearly accelerated by the intervention of treadmill training with partial body weight support, without compromising the stability of the knee joints in a given follow-up period.

Partially ordered models

NARCIS (Netherlands)

Fernandez, R.; Deveaux, V.

2010-01-01

We provide a formal definition and study the basic properties of partially ordered chains (POC). These systems were proposed to model textures in image processing and to represent independence relations between random variables in statistics (in the later case they are known as Bayesian networks).

Power generation from biomass: Status report on catalytic-allothermal wood gasification. Papers; Energetische Nutzung von Biomasse: Stand der Realisierung der katalytisch-allothermen Holzvergasung. Vortraege

Energy Technology Data Exchange (ETDEWEB)

Spindler, H.; Bauermeister, U.; Kliche, H.; Seiffarth, K. (comps.)

2001-12-01

The topic of this event is bound up with the activities of FOeST in the field of gasification of biomass in decentralized small plants (< 2 MW{sub el}). The start project was a research work in 1993 to select a gasification process for using wood, sludge or plastic waste, continued 1995 by a research project with gasification tests of tar oil contaminated wood in a small gasification reactor with good results in environmental compatibility. But the following planning process of a demonstration plant for 500 kW{sub el} has shown, that the biomass gasification couldn't reach economic efficiency. Due to the development of an catalytic-partial allothermal gasification process of GNS ltd. it was clear, that the technical efficiency could be increased considerably. So, in 2000, a project started to test this catalytic-partial allothermal gasification in a pilot plant. Today the results of research, development and testing of biomass gasification with catalytic-partial allothermal processing as well as practically experience with a gasification plant, general conditions and further activities for energetically utilisation of biomass in Saxonia-Anhalt will be presented. (orig.)

GC of catalytic reactions products involved in the promising fuel synthesis

Energy Technology Data Exchange (ETDEWEB)

Zheivot, V.; Sazonova, N. [Russian Academy of Sciences, Novosibirsk (Russian Federation). Boreskov Inst. of Catalysis

2012-09-15

Catalytic reactions involved in the synthesis of the promising kinds of novel fuel and products formed in these reactions were systematized according to the resulting fuel type. Generalization of the retention of the substances comprising these products is presented. Chromatograms exhibiting their separation on chromatographic materials with the surface of different chemical properties are summarized. We propose procedures for gas-chromatographic analysis of the catalytic reactions products formed in the synthesis of hydrogen, methanol, dimethyl ether and hydrocarbons as a new generation of fuel alternative to petroleum and coal. For partial oxidation of methane into synthesis gas, on-line determination of the components obtained in the reaction was carried out by gas chromatography and gas analyzer based on different physicochemical methods (IR spectroscopy and electrochemical methods). Similarity of the results obtained using these methods is demonstrated. (orig.)

Forced thermal cycling of catalytic reactions: experiments and modelling

DEFF Research Database (Denmark)

Jensen, Søren; Olsen, Jakob Lind; Thorsteinsson, Sune

2007-01-01

Recent studies of catalytic reactions subjected to fast forced temperature oscillations have revealed a rate enhancement increasing with temperature oscillation frequency. We present detailed studies of the rate enhancement up to frequencies of 2.5 Hz. A maximum in the rate enhancement is observed...... at about 1 Hz. A model for the rate enhancement that includes the surface kinetics and the dynamic partial pressure variations in the reactor is introduced. The model predicts a levelling off of the rate enhancement with frequency at about 1 Hz. The experimentally observed decrease above 1 Hz is explained...

Catalytic Reforming of Higher Hydrocarbon Fuels to Hydrogen: Process Investigations with Regard to Auxiliary Power Units

OpenAIRE

Kaltschmitt, Torsten

2012-01-01

This thesis discusses the investigation of the catalytic partial oxidation on rhodium-coated honeycomb catalysts with respect to the conversion of a model surrogate fuel and commercial diesel fuel into hydrogen for the use in auxiliary power units. Furthermore, the influence of simulated tail-gas recycling was investigated.

Comparative study of non-premixed and partially-premixed combustion simulations in a realistic Tay model combustor

OpenAIRE

Zhang, K.; Ghobadian, A.; Nouri, J. M.

2017-01-01

A comparative study of two combustion models based on non-premixed assumption and partially premixed assumptions using the overall models of Zimont Turbulent Flame Speed Closure Method (ZTFSC) and Extended Coherent Flamelet Method (ECFM) are conducted through Reynolds stress turbulence modelling of Tay model gas turbine combustor for the first time. The Tay model combustor retains all essential features of a realistic gas turbine combustor. It is seen that the non-premixed combustion model fa...

HYBRID SELECTIVE NON-CATALYTIC REDUCTION (SNCR)/SELECTIVE CATALYTIC REDUCTION (SCR) DEMONSTRATION FOR THE REMOVAL OF NOx FROM BOILER FLUE GASES; FINAL

International Nuclear Information System (INIS)

Jerry B. Urbas

1999-01-01

The U. S. Department of Energy (DOE), Electric Power Research Institute (EPRI), Pennsylvania Electric Energy Research Council, (PEERC), New York State Electric and Gas and GPU Generation, Inc. jointly funded a demonstration to determine the capabilities for Hybrid SNCR/SCR (Selective Non-Catalytic Reduction/Selective Catalytic Reduction) technology. The demonstration site was GPU Generation's Seward Unit No.5 (147MW) located in Seward Pennsylvania. The demonstration began in October of 1997 and ended in December 1998. DOE funding was provided through Grant No. DE-FG22-96PC96256 with T. J. Feeley as the Project Manager. EPRI funding was provided through agreements TC4599-001-26999 and TC4599-002-26999 with E. Hughes as the Project Manager. This project demonstrated the operation of the Hybrid SNCR/SCR NO(sub x) control process on a full-scale coal fired utility boiler. The hybrid technology was expected to provide a cost-effective method of reducing NO(sub x) while balancing capital and operation costs. An existing urea based SNCR system was modified with an expanded-duct catalyst to provide increased NO(sub x) reduction efficiency from the SNCR while producing increased ammonia slip levels to the catalyst. The catalyst was sized to reduce the ammonia slip to the air heaters to less than 2 ppm while providing equivalent NO(sub x) reductions. The project goals were to demonstrate hybrid technology is capable of achieving at least a 55% reduction in NO(sub x) emissions while maintaining less than 2ppm ammonia slip to the air heaters, maintain flyash marketability, verify the cost benefit and applicability of Hybrid post combustion technology, and reduce forced outages due to ammonium bisulfate (ABS) fouling of the air heaters. Early system limitations, due to gas temperature stratification, restricted the Hybrid NO(sub x) reduction capabilities to 48% with an ammonia slip of 6.1 mg/Nm(sup 3) (8 ppm) at the catalyst inlet. After resolving the stratification problem

Radiation catalytical effects in the pre-irradiated and thermally treated catalyst BASF K-3-10

International Nuclear Information System (INIS)

Motl, A.

1987-01-01

The effects of different heat treatment methods on radiation catalysis, induced by pre-irradiation of the BASF K-3-10 catalyst by γ- or β-radiation or by fast neutrons were investigated. It was found that calcination of the irradiated non-reduced catalyst resulted in a strong decrease in or even a total disappearance of the final radiation catalytical effects; however, at the same time the catalytical activity of the unirradiated catalyst was found to increase. The calcination of the catalyst in a nitrogen atmosphere after reduction also led to a substantial decrease in the resulting positive radiation catalytical effects and the exceedance of a certain calcination temperature also resulted in a decrease in the unirradiated catalyst activity. It could be concluded that calcination in nitrogen of the reduced irradiated samples decreased the radiation catalytical effects to a lesser degree than the calcination in the air of the non-reduced irradiated samples. In both cases, a different thermal stability of effects induced by different types of ionizing radiation was observed and it was found that it increased in the sequence beta radiation - gamma radiation - fast neutrons. The investigation of the γ radiation dose dependence of the radiation catalytical effect on the catalyst calcined before irradiation in the presence of air showed that the final radiation catalytical effects were lower than those observed in case of similarly irradiated but non-calcined samples. The dose dependence of the effect had the same character in both cases. (author). 3 tabs., 8 refs

Catalytic copyrolysis of cork oak and bio-oil distillation residue

Science.gov (United States)

Lee, Yejin; Oh, Daejun; Kim, Young-Min; Jae, Jungho; Jung, Sang-Chul; Jeon, Jong-Ki; Kim, Sang Chai; Park, Young-Kwon

2018-01-01

The atmospheric distillation residue (ADR) of cork oak (CO) pyrolysis oil was used as the co-feeding material for the catalytic pyrolysis of CO over HZSM-5 catalysts to improve the formation of aromatic hydrocarbons. Although the non-catalytic copyrolysis of CO and ADR did not improve the formation of aromatic hydrocarbons, the catalytic copyrolysis of CO and ADR promoted the synergistic formation of aromatic hydrocarbons. HZSM-5(30), having a lower SiO2/Al2O3(30), showed better performance for the formation of aromatic hydrocarbons than HZSM-5(80) because of its higher acidity. The catalytic copyrolysis of CO and ADR also decreased the formation of coke. The largest quantity of aromatic hydrocarbons was obtained from the catalytic copyrolysis of CO and ADR over HZSM-5 (30) at 600 °C, whereas the lowest coke yield was achieved at 700 °C. When the catalyst to sample ratio was increased from 2:1 to 5:1, the synergistic formation of aromatic hydrocarbons was limited, resulting in a lower experimental yield of aromatic hydrocarbons than the theoretical yield. A lower coke yield was also achieved at a high catalyst to sample ratio (5:1).

Challenge of non-precious metal oxide-based cathode for polymer electrolyte fuel cell

Energy Technology Data Exchange (ETDEWEB)

Ishihara, Akimitsu; Matsuzawa, Koichi; Mitsushima, Shigenori; Ota, Ken-ichiro [Yokohama National Univ. (Japan)

2010-07-01

The partially oxidized TaC{sub 0.58}N{sub 0.42} was investigated as non-platinum cathode for PEFC. In order to quantify the degree of oxidation, the degree of oxidation (DOO) was defined using the XRD peaks of Ta-CN and Ta{sub 2}O{sub 5}. The onset potential for the oxidation reduction reaction (ORR) had high value, that is, 0.9 V vs. RHE (reversible hydrogen electrode), at higher oxidation state of the TaC{sub 0.58}N{sub 0.42}. We found that the partial oxidation of TaC{sub 0.58}N{sub 0.42} was greatly useful to enhance the catalytic activity for the ORR. The volcano plot of the ionization potential vs. the E{sub ORR} suggested that there was a suitable interaction between the surface of the partially oxidized TaC{sub 0.58}N{sub 0.42} and oxygen. (orig.)

Partial distance correlation with methods for dissimilarities

OpenAIRE

Székely, Gábor J.; Rizzo, Maria L.

2014-01-01

Distance covariance and distance correlation are scalar coefficients that characterize independence of random vectors in arbitrary dimension. Properties, extensions, and applications of distance correlation have been discussed in the recent literature, but the problem of defining the partial distance correlation has remained an open question of considerable interest. The problem of partial distance correlation is more complex than partial correlation partly because the squared distance covari...

Optimization of non-catalytic transesterification of tobacco (Nicotiana tabacum) seed oil using supercritical methanol to biodiesel production

International Nuclear Information System (INIS)

García-Martínez, Nuria; Andreo-Martínez, Pedro; Quesada-Medina, Joaquín; Pérez de los Ríos, Antonia Pérez; Chica, Antonio; Beneito-Ruiz, Rubén; Carratalá-Abril, Juan

2017-01-01

Highlights: • Biodiesel from tobacco oil was produced by non-catalytic supercritical methanolysis. • Maximum experimental yield of FAMEs (92.8%) was reached at 300 °C and 90 min. • Optimal conditions by RSM (303.4 °C and 90 min) predicted a maximum FAME yield of 91.1%. • Thermal decomposition of biodiesel was observed above 325 °C and 60 min of reaction. • Glycerol generated at 300 °C and 90 min was degraded and incorporated to the biodiesel. - Abstract: The biodiesel production from non-edible oils has high potential as renewable and ecological fuel. Few researches have been conducted to date on the production of biodiesel from tobacco (Nicotiana tabacum) seed oil. The aim of this study was to optimize the biodiesel production from this crude oil by non-catalytic supercritical methanolysis using response surface methodology (RSM). Triglyceride conversion, total and individual FAME yield, monoglyceride and diglyceride yield, and thermal decomposition degree of biodiesel were determined in the temperature and reaction time ranges of 250–350 °C (12–43 MPa) and 15–90 min, respectively, at a fixed methanol-to-oil molar ratio of 43:1. According to the RSM, the optimal conditions were 303.4 °C and 90 min, reaching a predicted maximum FAME yield of 91.1 ± 3.2 mol%. This maximum was very close to that obtained experimentally (92.8 ± 2.1 mol%) at 300 °C and 90 min. Decomposition of biodiesel became evident at 325 °C and 60 min of reaction due to the thermal instability of unsaturated methyl esters (methyl linoleate and oleate). The biodiesel obtained in the best experimental reaction conditions (300 °C and 90 min), where no thermal decomposition of FAMEs was observed, contained most of the byproduct glycerol generated, which was degraded and incorporated to the product. This biodiesel basically failed to meet the content of FAMEs as required by the standard EN 14214, the content of monoglycerides and total glycerol, and the acid value, being a

Isotropic non-white matter partial volume effects in constrained spherical deconvolution.

Science.gov (United States)

Roine, Timo; Jeurissen, Ben; Perrone, Daniele; Aelterman, Jan; Leemans, Alexander; Philips, Wilfried; Sijbers, Jan

2014-01-01

Diffusion-weighted (DW) magnetic resonance imaging (MRI) is a non-invasive imaging method, which can be used to investigate neural tracts in the white matter (WM) of the brain. Significant partial volume effects (PVEs) are present in the DW signal due to relatively large voxel sizes. These PVEs can be caused by both non-WM tissue, such as gray matter (GM) and cerebrospinal fluid (CSF), and by multiple non-parallel WM fiber populations. High angular resolution diffusion imaging (HARDI) methods have been developed to correctly characterize complex WM fiber configurations, but to date, many of the HARDI methods do not account for non-WM PVEs. In this work, we investigated the isotropic PVEs caused by non-WM tissue in WM voxels on fiber orientations extracted with constrained spherical deconvolution (CSD). Experiments were performed on simulated and real DW-MRI data. In particular, simulations were performed to demonstrate the effects of varying the diffusion weightings, signal-to-noise ratios (SNRs), fiber configurations, and tissue fractions. Our results show that the presence of non-WM tissue signal causes a decrease in the precision of the detected fiber orientations and an increase in the detection of false peaks in CSD. We estimated 35-50% of WM voxels to be affected by non-WM PVEs. For HARDI sequences, which typically have a relatively high degree of diffusion weighting, these adverse effects are most pronounced in voxels with GM PVEs. The non-WM PVEs become severe with 50% GM volume for maximum spherical harmonics orders of 8 and below, and already with 25% GM volume for higher orders. In addition, a low diffusion weighting or SNR increases the effects. The non-WM PVEs may cause problems in connectomics, where reliable fiber tracking at the WM-GM interface is especially important. We suggest acquiring data with high diffusion-weighting 2500-3000 s/mm(2), reasonable SNR (~30) and using lower SH orders in GM contaminated regions to minimize the non-WM PVEs in CSD.

Trapping and partial characterization of an adduct postulated to be the covalent catalytic ternary complex of thymidylate synthetase

International Nuclear Information System (INIS)

Ahmed, F.; Moore, M.A.; Dunlap, R.B.

1986-01-01

The proposed mechanism of action of thymidylate synthetase envisages the formation of a covalent ternary complex of the enzyme via the active site cysteine with dUMP and 5,10-methylenetetrahydrofolate (CH 2 H 4 folate). The authors recent success in using trichloroacetic acid to trap the covalent enzyme-FdUMP binary and ternary (enzyme-FdUMP-CH 2 H 4 folate) complexes led to the use of this technique in attempts to trap the transient covalent catalytic ternary complex. Experiments performed with [2-C 14 ]dUMP and 3 H-CH 2 H 4 folate show that both these ligands remained bound to the enzyme after trichloroacetic acid precipitation. The trapped covalent catalytic ternary complex was subjected to CNBr fragmentation, and the peptides were fractionated by HPLC. The isolated active-site peptide was shown to retain the two ligands and was subjected to a limited sequence analysis by the dansyl-Edman procedure. The inhibitory ternary complex formed with 14 C-FdUMP and 3 H-CH 2 4 folate served as a control. The active-site peptides isolated from the CNBr treated inhibitory ternary complex and the catalytic complex exhibited identical sequences for the first four N-terminal residues, Ala-Leu-Pro-Pro, and the fifth residue was found to be associated with the labeled ligands. Sequence analysis of the active site peptide derived from the carboxymethylated enzyme confirmed this sequence and the 5th residue was shown to be Cm-Cys

Studies of non-isothermal flow in saturated and partially saturated porous media

International Nuclear Information System (INIS)

Ho, C.K.; Maki, K.S.; Glass, R.J.

1993-01-01

Physical and numerical experiments have been performed to investigate the behavior of nonisothermal flow in two-dimensional saturated and partially saturated porous media. The physical experiments were performed to identify non-isothermal flow fields and temperature distributions in fully saturated, half-saturated, and residually saturated two-dimensional porous media with bottom heating and top cooling. Two counter-rotating liquid-phase convective cells were observed to develop in the saturated regions of all three cases. Gas-phase convection was also evidenced in the unsaturated regions of the partially saturated experiments. TOUGH2 numerical simulations of the saturated case were found to be strongly dependent on the assumed boundary conditions of the physical system. Models including heat losses through the boundaries of the test cell produced temperature and flow fields that were in better agreement with the observed temperature and flow fields than models that assumed insulated boundary conditions. A sensitivity analysis also showed that a reduction of the bulk permeability of the porous media in the numerical simulations depressed the effects of convection, flattening the temperature profiles across the test cell

Selective catalytic reduction of sulfur dioxide to elemental sulfur. Final report

Energy Technology Data Exchange (ETDEWEB)

Liu, W.; Flytzani-Stephanopoulos, M.; Sarofim, A.F.

1995-06-01

This project has investigated new metal oxide catalysts for the single stage selective reduction of SO{sub 2} to elemental sulfur by a reductant, such as CO. Significant progress in catalyst development has been made during the course of the project. We have found that fluorite oxides, CeO{sub 2} and ZrO{sub 2}, and rare earth zirconates such as Gd{sub 2}Zr{sub 2}O{sub 7} are active and stable catalysts for reduction Of SO{sub 2} by CO. More than 95% sulfur yield was achieved at reaction temperatures about 450{degrees}C or higher with the feed gas of stoichiometric composition. Reaction of SO{sub 2} and CO over these catalysts demonstrated a strong correlation of catalytic activity with the catalyst oxygen mobility. Furthermore, the catalytic activity and resistance to H{sub 2}O and CO{sub 2} poisoning of these catalysts were significantly enhanced by adding small amounts of transition metals, such as Co, Ni, Co, etc. The resulting transition metal-fluorite oxide composite catalyst has superior activity and stability, and shows promise in long use for the development of a greatly simplified single-step sulfur recovery process to treat variable and dilute SO{sub 2} concentration gas streams. Among various active composite catalyst systems the Cu-CeO{sub 2} system has been extensively studied. XRD, XPS, and STEM analyses of the used Cu-CeO{sub 2} catalyst found that the fluorite crystal structure of ceria was stable at the present reaction conditions, small amounts of copper was dispersed and stabilized on the ceria matrix, and excess copper oxide particles formed copper sulfide crystals of little contribution to catalytic activity. A working catalyst consisted of partially sulfated cerium oxide surface and partially sulfided copper clusters. The overall reaction kinetics were approximately represented by a first order equation.

Catalytic pyrolysis of microalgae to high-quality liquid bio-fuels

International Nuclear Information System (INIS)

Babich, I.V.; Hulst, M. van der; Lefferts, L.; Moulijn, J.A.; O'Connor, P.; Seshan, K.

2011-01-01

The pyrolytic conversion of chlorella algae to liquid fuel precursor in presence of a catalyst (Na 2 CO 3 ) has been studied. Thermal decomposition studies of the algae samples were performed using TGA coupled with MS. Liquid oil samples were collected from pyrolysis experiments in a fixed-bed reactor and characterized for water content and heating value. The oil composition was analyzed by GC-MS. Pretreatment of chlorella with Na 2 CO 3 influences the primary conversion of chlorella by shifting the decomposition temperature to a lower value. In the presence of Na 2 CO 3 , gas yield increased and liquid yield decreased when compared with non-catalytic pyrolysis at the same temperatures. However, pyrolysis oil from catalytic runs carries higher heating value and lower acidity. Lower content of acids in the bio-oil, higher aromatics, combined with higher heating value show promise for production of high-quality bio-oil from algae via catalytic pyrolysis, resulting in energy recovery in bio-oil of 40%. -- Highlights: → The pyrolytic catalytic conversion of chlorella algae to liquid fuel precursor. → Na 2 CO 3 as a catalyst for the primary conversion of chlorella. → Pyrolysis oil from catalytic runs carries higher heating value and lower acidity. → High-quality bio-oil from algae via catalytic pyrolysis with energy recovery in bio-oil of 40%.

Catalytic Properties and Immobilization Studies of Catalase from Malva sylvestris L.

OpenAIRE

Arabaci, G.; Usluoglu, A.

2013-01-01

Catalase was partially purified from Malva sylvestris L. and immobilized onto chitosan. Then, its catalytic properties were investigated. (NH4)2SO4 precipitation and dialysis were performed in the extracted enzyme. Further purification was performed with sephadex G-200 column. Kinetic studies of the purified enzyme activity were measured and characterized. The inhibitory effects of KCN, NaN3, CuSO4, and EDTA on M. sylvestris L. catalase activity were observed except NaCl. Furthermore, M. sylv...

Large-area imaging reveals biologically driven non-random spatial patterns of corals at a remote reef

Science.gov (United States)

Edwards, Clinton B.; Eynaud, Yoan; Williams, Gareth J.; Pedersen, Nicole E.; Zgliczynski, Brian J.; Gleason, Arthur C. R.; Smith, Jennifer E.; Sandin, Stuart A.

2017-12-01

For sessile organisms such as reef-building corals, differences in the degree of dispersion of individuals across a landscape may result from important differences in life-history strategies or may reflect patterns of habitat availability. Descriptions of spatial patterns can thus be useful not only for the identification of key biological and physical mechanisms structuring an ecosystem, but also by providing the data necessary to generate and test ecological theory. Here, we used an in situ imaging technique to create large-area photomosaics of 16 plots at Palmyra Atoll, central Pacific, each covering 100 m2 of benthic habitat. We mapped the location of 44,008 coral colonies and identified each to the lowest taxonomic level possible. Using metrics of spatial dispersion, we tested for departures from spatial randomness. We also used targeted model fitting to explore candidate processes leading to differences in spatial patterns among taxa. Most taxa were clustered and the degree of clustering varied by taxon. A small number of taxa did not significantly depart from randomness and none revealed evidence of spatial uniformity. Importantly, taxa that readily fragment or tolerate stress through partial mortality were more clustered. With little exception, clustering patterns were consistent with models of fragmentation and dispersal limitation. In some taxa, dispersion was linearly related to abundance, suggesting density dependence of spatial patterning. The spatial patterns of stony corals are non-random and reflect fundamental life-history characteristics of the taxa, suggesting that the reef landscape may, in many cases, have important elements of spatial predictability.

The influence of removable partial dentures on the periodontal health of abutment and non-abutment teeth

OpenAIRE

Dula, Linda J.; Shala, Kujtim Sh.; Pustina–Krasniqi, Teuta; Bicaj, Teuta; Ahmedi, Enis F.

2015-01-01

Objective: The aim of this study was to evaluate the influence of removable partial dentures (RPD) on the periodontal health of abutment and non-abutment teeth. Materials and Methods: A total 107 patients with RPD participated in this study. It was examined 138 RPD, they were 87 with clasp-retained and 51 were RPD with attachments. The following periodontal parameters were evaluated for abutment and non-abutment teeth, plaque index (PLI), calculus index (CI), bleeding on probing (BOP), probin...

COAL CONVERSION WASTEWATER TREATMENT BY CATALYTIC OXIDATION IN SUPERCRITICAL WATER; FINAL

International Nuclear Information System (INIS)

Phillip E. Savage

1999-01-01

Wastewaters from coal-conversion processes contain phenolic compounds in appreciable concentrations. These compounds need to be removed so that the water can be discharged or re-used. Catalytic oxidation in supercritical water is one potential means of treating coal-conversion wastewaters, and this project examined the reactions of phenol over different heterogeneous oxidation catalysts in supercritical water. More specifically, we examined the oxidation of phenol over a commercial catalyst and over bulk MnO(sub 2), bulk TiO(sub 2), and CuO supported on Al(sub 2) O(sub 3). We used phenol as the model pollutant because it is ubiquitous in coal-conversion wastewaters and there is a large database for non-catalytic supercritical water oxidation (SCWO) with which we can contrast results from catalytic SCWO. The overall objective of this research project is to obtain the reaction engineering information required to evaluate the utility of catalytic supercritical water oxidation for treating wastes arising from coal conversion processes. All four materials were active for catalytic supercritical water oxidation. Indeed, all four materials produced phenol conversions and CO(sub 2) yields in excess of those obtained from purely homogeneous, uncatalyzed oxidation reactions. The commercial catalyst was so active that we could not reliably measure reaction rates that were not limited by pore diffusion. Therefore, we performed experiments with bulk transition metal oxides. The bulk MnO(sub 2) and TiO(sub 2) catalysts enhance both the phenol disappearance and CO(sub 2) formation rates during SCWO. MnO(sub 2) does not affect the selectivity to CO(sub 2), or to the phenol dimers at a given phenol conversion. However, the selectivities to CO(sub 2) are increased and the selectivities to phenol dimers are decreased in the presence of TiO(sub 2) , which are desirable trends for a catalytic SCWO process. The role of the catalyst appears to be accelerating the rate of formation of

Steam reformer with catalytic combustor

Science.gov (United States)

Voecks, Gerald E. (Inventor)

1990-01-01

A steam reformer is disclosed having an annular steam reforming catalyst bed formed by concentric cylinders and having a catalytic combustor located at the center of the innermost cylinder. Fuel is fed into the interior of the catalytic combustor and air is directed at the top of the combustor, creating a catalytic reaction which provides sufficient heat so as to maintain the catalytic reaction in the steam reforming catalyst bed. Alternatively, air is fed into the interior of the catalytic combustor and a fuel mixture is directed at the top. The catalytic combustor provides enhanced radiant and convective heat transfer to the reformer catalyst bed.

Hydrogen production with short contact time. Catalytic partial oxidation of hydrocarbons and oxygenated compounds: Recent advances in pilot- and bench-scale testing and process design

Energy Technology Data Exchange (ETDEWEB)

Guarinoni, A.; Ponzo, R.; Basini, L. [ENI Refining and Marketing Div., San Donato Milanese (Italy)

2010-12-30

ENI R and D has been active for fifteen years in the development of Short Contact Time - Catalytic Partial Oxidation (SCT-CPO) technologies for producing Hydrogen/Synthesis Gas. From the beginning the experimental work addressed either at defining the fundamental principles or the technical and economical potential of the technology. Good experimental responses, technical solutions' simplicity and flexibility, favourable techno-economical evaluations promoted the progressive widening of the field of the investigations. From Natural Gas (NG) the range of ''processable'' Hydrocarbons extended to Liquefied Petroleum Gas (LPG) and Gasoils, including those characterised by high levels of unsaturated and sulphurated molecules and, lately, to other compounds with biological origin. The extensive work led to the definition of different technological solutions, grouped as follows: Technology 1: Air Blown SCT-CPO of Gaseous Hydrocarbons and/or Light Compounds with biological origin Technology 2: Enriched Air/Oxygen Blown SCT-CPO of Gaseous Hydrocarbons and/or Light Compounds with biological origin Technology 3: Enriched Air/Oxygen Blown SCT-CPO of Liquid Hydrocarbons and/or Compounds with biological origin Recently, the licence rights on a non-exclusive basis for the commercialisation of SCT-CPO based processes for H{sub 2}/Synthesis gas production from light hydrocarbons with production capacity lower than 5,000 Nm{sup 3}/h of H{sub 2} or 7,500 Nm3/h of syngas have been assigned to two external companies. In parallel, development of medium- and large-scale plant solutions is progressing within the ENI group framework. These last activities are addressed to the utilisation of SCT-CPO for matching the variable Hydrogen demand in several contexts of oil refining operation. This paper will report on the current status of SCT-CPO with a focus on experimental results obtained, either at pilot- and bench- scale level. (orig.)

Feasibility study of a reverse flow catalytic membrane reactor with porous membranes for the production of syngas

NARCIS (Netherlands)

Smit, J.; van Sint Annaland, M.; Kuipers, J.A.M.

2005-01-01

In this paper a novel reverse flow catalytic membrane reactor (RFCMR) is proposed for the partial oxidation of CH4 to syngas. The feasibility of the RFCMR concept has been investigated for industrial conditions on basis of a simulation study employing a reactor model, which includes a detailed

Network meta-analysis incorporating randomized controlled trials and non-randomized comparative cohort studies for assessing the safety and effectiveness of medical treatments: challenges and opportunities

OpenAIRE

Cameron, Chris; Fireman, Bruce; Hutton, Brian; Clifford, Tammy; Coyle, Doug; Wells, George; Dormuth, Colin R.; Platt, Robert; Toh, Sengwee

2015-01-01

Network meta-analysis is increasingly used to allow comparison of multiple treatment alternatives simultaneously, some of which may not have been compared directly in primary research studies. The majority of network meta-analyses published to date have incorporated data from randomized controlled trials (RCTs) only; however, inclusion of non-randomized studies may sometimes be considered. Non-randomized studies can complement RCTs or address some of their limitations, such as short follow-up...

Non-Hermitian Extensions of Wishart Random Matrix Ensembles

International Nuclear Information System (INIS)

Akemann, G.

2011-01-01

We briefly review the solution of three ensembles of non-Hermitian random matrices generalizing the Wishart-Laguerre (also called chiral) ensembles. These generalizations are realized as Gaussian two-matrix models, where the complex eigenvalues of the product of the two independent rectangular matrices are sought, with the matrix elements of both matrices being either real, complex or quaternion real. We also present the more general case depending on a non-Hermiticity parameter, that allows us to interpolate between the corresponding three Hermitian Wishart ensembles with real eigenvalues and the maximally non-Hermitian case. All three symmetry classes are explicitly solved for finite matrix size N x M for all complex eigenvalue correlations functions (and real or mixed correlations for real matrix elements). These are given in terms of the corresponding kernels built from orthogonal or skew-orthogonal Laguerre polynomials in the complex plane. We then present the corresponding three Bessel kernels in the complex plane in the microscopic large-N scaling limit at the origin, both at weak and strong non-Hermiticity with M - N ≥ 0 fixed. (author)

Thickness-controlled direct growth of nanographene and nanographite film on non-catalytic substrates

Science.gov (United States)

Du, Lei; Yang, Liu; Hu, Zhiting; Zhang, Jiazhen; Huang, Chunlai; Sun, Liaoxin; Wang, Lin; Wei, Dacheng; Chen, Gang; Lu, Wei

2018-05-01

Metal-catalyzed chemical vapor deposition (CVD) has been broadly employed for large-scale production of high-quality graphene. However, a following transfer process to targeted substrates is needed, which is incompatible with current silicon technology. We here report a new CVD approach to form nanographene and nanographite films with accurate thickness control directly on non-catalytic substrates such as silicon dioxide and quartz at 800 °C. The growth time is as short as a few seconds. The approach includes using 9-bis(diethylamino)silylanthracene as the carbon source and an atomic layer deposition (ALD) controlling system. The structure of the formed nanographene and nanographite films were characterized using atomic force microscopy, high resolution transmission electron microscopy, Raman scattering, and x-ray photoemission spectroscopy. The nanographite film exhibits a transmittance higher than 80% at 550 nm and a sheet electrical resistance of 2000 ohms per square at room temperature. A negative temperature-dependence of the resistance of the nanographite film is also observed. Moreover, the thickness of the films can be precisely controlled via the deposition cycles using an ALD system, which promotes great application potential for optoelectronic and thermoelectronic-devices.

Catalytic Activity Control via Crossover between Two Different Microstructures

KAUST Repository

Zhou, Yuheng

2017-09-08

Metal nanocatalysts hold great promise for a wide range of heterogeneous catalytic reactions, while the optimization strategy of catalytic activity is largely restricted by particle size or shape control. Here, we demonstrate that a reversible microstructural control through the crossover between multiply-twinned nanoparticle (MTP) and single crystal (SC) can be readily achieved by solvent post-treatment on gold nanoparticles (AuNPs). Polar solvents (e.g. water, methanol) direct the transformation from MTP to SC accompanied by the disappearance of twinning and stacking faults. A reverse transformation from SC to MTP is achieved in non-polar solvent (e.g. toluene) mixed with thiol ligands. The transformation between two different microstructures is directly observed by in-situ TEM and leads to a drastic modulation of catalytic activity towards the gas-phase selective oxidation of alcohols. There is a quasi-linear relationship between TOFs and MTP concentrations. Based on the combined experimental and theoretical investigations of alcohol chemisorption on these nanocatalysts, we propose that the exposure of {211}-like microfacets associated with twin boundaries and stack faults accounts for the strong chemisorption of alcohol molecules on MTP AuNPs and thus the exceptionally high catalytic activity.

Predicting the catalytic sites of isopenicillin N synthase (IPNS ...

African Journals Online (AJOL)

Isopenicillin N synthase (IPNS) related Non-haem iron-dependent oxygenases and oxidases (NHIDOX) demonstrated a striking structural conservativeness, even with low protein sequence homology. It is evident that these enzymes have an architecturally similar catalytic centre with active ligands lining the reactive pocket.

Trapping and partial characterization of an adduct postulated to be the covalent catalytic ternary complex of thymidylate synthetase

Energy Technology Data Exchange (ETDEWEB)

Ahmed, F.; Moore, M.A.; Dunlap, R.B.

1986-05-01

The proposed mechanism of action of thymidylate synthetase envisages the formation of a covalent ternary complex of the enzyme via the active site cysteine with dUMP and 5,10-methylenetetrahydrofolate (CH/sub 2/H/sub 4/folate). The authors recent success in using trichloroacetic acid to trap the covalent enzyme-FdUMP binary and ternary (enzyme-FdUMP-CH/sub 2/H/sub 4/folate) complexes led to the use of this technique in attempts to trap the transient covalent catalytic ternary complex. Experiments performed with (2-C/sup 14/)dUMP and /sup 3/H-CH/sub 2/H/sub 4/folate show that both these ligands remained bound to the enzyme after trichloroacetic acid precipitation. The trapped covalent catalytic ternary complex was subjected to CNBr fragmentation, and the peptides were fractionated by HPLC. The isolated active-site peptide was shown to retain the two ligands and was subjected to a limited sequence analysis by the dansyl-Edman procedure. The inhibitory ternary complex formed with /sup 14/C-FdUMP and /sup 3/H-CH/sub 2/ /sub 4/folate served as a control. The active-site peptides isolated from the CNBr treated inhibitory ternary complex and the catalytic complex exhibited identical sequences for the first four N-terminal residues, Ala-Leu-Pro-Pro, and the fifth residue was found to be associated with the labeled ligands. Sequence analysis of the active site peptide derived from the carboxymethylated enzyme confirmed this sequence and the 5th residue was shown to be Cm-Cys.

The effect of temperature on the catalytic conversion of Kraft lignin using near-critical water

DEFF Research Database (Denmark)

Nguyen, Thi Dieu Huyen; Maschietti, Marco; Åmand, Lars-Erik

2014-01-01

The catalytic conversion of suspended LignoBoost Kraft lignin was performed in near-critical water using ZrO2/K2CO3 as the catalytic system and phenol as the co-solvent and char suppressing agent. The reaction temperature was varied from 290 to 370 C and its effect on the process was investigated...... in a continuous flow (1 kg/h). The yields of water-soluble organics (WSO), bio-oil and char (dry lignin basis) were in the ranges of 5–11%, 69–87% and 16–22%, respectively. The bio-oil, being partially deoxygenated, exhibited higher carbon content and heat value, but lower sulphur content than lignin. The main 1...

Electro-catalytic oxidation of ethanol on platinum-iridium mixtures supported on glassy carbon

International Nuclear Information System (INIS)

Rodriguez, Henry; Hoyos Bibian

2004-01-01

Electro-catalytic oxidation of ethanol on platinum-iridium mixtures supported on glassy carbon was studied, in acid media at different temperatures and concentrations. During the maturation time of deposited iridium, the surface is covered by an irreversible oxide formation, which affects the behavior of the catalytic mixture. The Pt 7 0 Ir 3 0 and Pt 9 0 Ir 1 0 mixtures seem to be a little more active than the Pt/C electrode at potentials below 800 mV (vs. HRE). In all electrodes appears two reactions: partial ethanol oxidation to produce acetaldehyde (main path of reaction at low temperatures and high electrode coverage with ethanol adsorption residues) and the total oxidation to carbon dioxide which is considerable at potential above 800 mV and it is increased with increasing temperature

Isotropic non-white matter partial volume effects in constrained spherical deconvolution

Directory of Open Access Journals (Sweden)

Timo eRoine

2014-03-01

Full Text Available Diffusion-weighted (DW magnetic resonance imaging (MRI is a noninvasive imaging method, which can be used to investigate neural tracts in the white matter (WM of the brain. Significant partial volume effects (PVE are present in the DW signal due to relatively large voxel sizes. These PVEs can be caused by both non-WM tissue, such as gray matter (GM and cerebrospinal fluid (CSF, and by multiple nonparallel WM fiber populations. High angular resolution diffusion imaging (HARDI methods have been developed to correctly characterize complex WM fiber configurations, but to date, many of the HARDI methods do not account for non-WM PVEs. In this work, we investigated the isotropic PVEs caused by non-WM tissue in WM voxels on fiber orientations extracted with constrained spherical deconvolution (CSD. Experiments were performed on simulated and real DW-MRI data. In particular, simulations were performed to demonstrate the effects of varying the diffusion weightings, signal-to-noise ratios (SNR, fiber configurations, and tissue fractions.Our results show that the presence of non-WM tissue signal causes a decrease in the precision of the detected fiber orientations and an increase in the detection of false peaks in CSD. We estimated 35-50 % of WM voxels to be affected by non-WM PVEs. For HARDI sequences, which typically have a relatively high degree of diffusion weighting, these adverse effects are most pronounced in voxels with GM PVEs. The non-WM PVEs become severe with 50 % GM volume for maximum spherical harmonics orders of 8 and below, and already with 25 % GM volume for higher orders. In addition, a low diffusion weighting or SNR increases the effects. The non-WM PVEs may cause problems in connectomics, where reliable fiber tracking at the WM-GM interface is especially important. We suggest acquiring data with high diffusion-weighting 2500-3000 s/mm2, reasonable SNR (~30 and using lower SH orders in GM contaminated regions to minimize the non-WM PVEs

PEEM microscopy and DFT calculations of catalytically active platinum surfaces and interfaces

International Nuclear Information System (INIS)

Spiel, C.

2012-01-01

The aim of this thesis was to investigate the properties of catalytically active platinum surfaces and interfaces both with experimental and theoretical methods. Using experimental methods, catalytic CO oxidation on individual grains of a polycrystalline platinum foil was studied in situ under high vacuum (HV) conditions. A polycrystalline platinum foil consists of individual µm-sized crystal grains that are mainly [100]-, [110]- and [111]-oriented and differ significantly in their catalytic activity. In order to elucidate the differences existing between the reactivity of the individual grains, a combination of photoemission electron microscopy (PEEM) and quadrupole mass spectrometry (QMS) was used in this work. The working principle of PEEM is based on the photoelectric effect where illumination of the sample with (UV-)light causes emission of photoelectrons. The emitted photoelectrons are used to visualize the sample surface (with typical resolution in the low micrometer range). The PEEM image contrast originates from differences in the local work function that may arise due to different crystallographic orientations and/or changes in the adsorbate coverage. With a combination of PEEM and QMS, it was possible to study the kinetics of catalytic CO oxidation on polycrystalline platinum foil both in a global and a laterally-resolved way simultaneously. If catalytic CO oxidation on surfaces of platinum is followed at constant temperature and oxygen partial pressure under cyclic variation of the CO pressure, a hysteresis in the CO2 production rate is observed in the bistability region with two noticeable kinetic transitions (called tA and tB) taking place at different CO pressures when the catalyst surface switches back-and-forth between two steady states of high and low reactivity while the Pt-surface is, correspondingly, either oxygen- or CO-covered. In the bistability region between τ A and τ B , the system stays (at the same values of the external parameters p

MVP Chemotherapy and Hyperfractionated Radiotherapy for Stage III Unresectable Non-Small Cell Lung Cancer - Randomized for maintenance Chemotherapy vs. Observation; Preliminary Report-

International Nuclear Information System (INIS)

Choi, Euk Kyung; Chang, Hye Sook; Suh, Cheol Won

1991-01-01

To evaluate the effect of MVP chemotherapy and hyperfractionated radiotherapy in Stage III unresectable non small cell lung cancer (NSCLC), authors have conducted a prospective randomized study since January 1991. Stage IIIa or IIIb unresectable NSCLC patients were treated with hyperfractionated radiotherapy (120 cGy/fx BID) up to 6500 cGY following 3 cycles of induction MVP (Mitomycin C 6 mg/m 2 , vinblastine 6 mg/m 2 , Cisplatin 60 mg/m 2 ) and randomized for either observation or 3 cycles of maintenance MVP chemotherapy. Until August 1991, 18 patients were registered to this study. 4 cases were stage IIIa and 14 were stage IIIb. Among 18 cases 2 were lost after 2 cycles of chemotherapy, and 16 were analyzed for this preliminary report. The response rate of induction chemotherapy was 62.5%; partial response, 50% and minimal response, 12.5%. Residual tumor of the one partial responder was completely disappeared after radiotherapy. Among 6 cases who were progressed during induction chemotherapy, 4 of them were also progressed after radiotherapy. All patients were tolerated BID radiotherapy without definite increase of acute complications, compared with conventional radiotherapy group. But at the time of this report, one patient expired in two month after the completion of the radiotherapy because of treatment related complication. Although the longer follow up is needed, authors are encouraged with higher response rate and acceptable toxicity of this treatment. Authors believe that this study is worthwhile to continue

Catalytic conversion of CO2 into valuable products

International Nuclear Information System (INIS)

Pham-Huu, C.; Ledoux, M.J.

2008-01-01

Complete text of publication follows: Synthesis gas, a mixture of H 2 and CO, is an important feed-stock for several chemical processes operated in the production of methanol and synthetic fuels through a Fischer- Tropsch synthesis. Synthesis gas is produced via an endothermic steam reforming of methane (CH 4 + H 2 O → CO + 3H 2 , ΔH = +225.4 kJ.mol -1 ), catalytic or direct partial oxidation of methane (CH 4 + (1/2)O 2 → CO + 2H 2 , ΔH -38 kJ.mol -1 ) and CO 2 reforming of methane (CH 4 + CO 2 → 2CO + 2H 2 , ΔH= +247 kJ.mol -1 ). The main disadvantage of these processes is the high coke formation, essentially in the nano-filament form, which may cause severe deactivation of the catalyst by pore or active site blocking and sometimes, physical disintegration of the catalyst body causing a high pressure drop along the catalyst bed and even, in some cases, inducing damage to the reactor itself. Previous results obtained in the catalytic partial oxidation of methane have shown that due to the hot spot and carbon nano-filaments formation, especially in the case of the CO 2 reforming, the alumina-based catalyst in an extrudate form was broken into powder which induces a significant pressure drop across the catalytic bed. In the case of endothermic reactions, steam and CO 2 reforming, the temperature drop within the catalyst bed could also modified the activity of the catalyst. Silicon carbide (SiC) exhibits a high thermal conductivity, a high resistance towards oxidation, a high mechanical strength, and chemical inertness, all of which make it a good candidate for use as catalyst support in several endothermic and exothermic reactions such as dehydrogenation, selective partial oxidation, and Fischer-Tropsch synthesis. The gas-solid reaction allows the preparation of SiC with medium surface area, i.e. 10 to 40 m 2 .g -1 , and controlled macroscopic shape, i.e. grains, extrudates or foam, for it subsequence use as catalyst support. In addition, due to its chemical

Mammalian α-polymerase: cloning of partial complementary DNA and immunobinding of catalytic subunit in crude homogenate protein blots

International Nuclear Information System (INIS)

SenGupta, D.N.; Kumar, P.; Zmudzka, B.Z.; Coughlin, S.; Vishwanatha, J.K.; Robey, F.A.; Parrott, C.; Wilson, S.H.

1987-01-01

A new polyclonal antibody against the α-polymerase catalytic polypeptide was prepared by using homogeneous HeLa cellα-polymerase. The antibody neutralized α-polymerase activity and was strong and specific for the α-polymerase catalytic polypeptide (M/sub r/ 183,000) in Western blot analysis of crude extracts of HeLa cells. The antibody was used to screen a cDNA library of newborn rat brain poly(A+) RNA in λgt11. A positive phage was identified and plaque purified. This phage, designated λpolα1.2, also was found to be positive with an antibody against Drosophila α-polymerase. The insert in λpolα1.2 (1183 base pairs) contained a poly(A) sequence at the 3' terminus and a short in-phase open reading frame at the 5' terminus. A synthetic oligopeptide (eight amino acids) corresponding to the open reading frame was used to raise antiserum in rabbits. Antibody affinity purified from this serum was found to be immunoreactive against purified α-polymerase by enzyme-linked immunosorbent assay and was capable of immunoprecipitating α-polymerase. This indicated the λpolα1.2 insert encoded an α-polymerase epitope and suggested that the cDNA corresponded to an α-polymerase mRNA. This was confirmed in hybrid selection experiments using pUC9 containing the cDNA insert and poly(A+) RNA from newborn rat brain; the insert hybridized to mRNA capable of encoding α-polymerase catalytic polypeptides. Northern blot analysis of rat brain poly(A+) RNA revealed that this mRNA is ∼5.4 kilobases

Developmental and growth defects in mice with combined deficiency of CK2 catalytic genes.

Science.gov (United States)

Landesman-Bollag, Esther; Belkina, Anna; Hovey, Beth; Connors, Edward; Cox, Charles; Seldin, David C

2011-10-01

The CK2 α and α' catalytic gene products have overlapping biochemical activity, but in vivo, their functions are very different. Deletion of both alleles of CK2α leads to mid-gestational embryonic lethality, while deletion of both alleles of CK2α' does not interfere with viability or development of embryos; however, adult CK2α'-/-males are infertile. To further elucidate developmental roles of CK2, and analyze functional overlap between the two catalytic genes, mice with combined knockouts were bred. Mice bearing any two CK2 catalytic alleles were phenotypically normal. However, inheritance of a single CK2α allele, without either CK2α' allele, resulted in partial embryonic lethality. Such mice that survived through embryogenesis were smaller at birth than littermate controls, and weighed less throughout life. However, their cardiac function and lifespan were normal. Fibroblasts derived from CK2α+/-CK2α'-/- embryos grew poorly in culture. These experiments demonstrate that combined loss of one CK2α allele and both CK2α' alleles leads to unique abnormalities of growth and development.

Partial Deconvolution with Inaccurate Blur Kernel.

Science.gov (United States)

Ren, Dongwei; Zuo, Wangmeng; Zhang, David; Xu, Jun; Zhang, Lei

2017-10-17

Most non-blind deconvolution methods are developed under the error-free kernel assumption, and are not robust to inaccurate blur kernel. Unfortunately, despite the great progress in blind deconvolution, estimation error remains inevitable during blur kernel estimation. Consequently, severe artifacts such as ringing effects and distortions are likely to be introduced in the non-blind deconvolution stage. In this paper, we tackle this issue by suggesting: (i) a partial map in the Fourier domain for modeling kernel estimation error, and (ii) a partial deconvolution model for robust deblurring with inaccurate blur kernel. The partial map is constructed by detecting the reliable Fourier entries of estimated blur kernel. And partial deconvolution is applied to wavelet-based and learning-based models to suppress the adverse effect of kernel estimation error. Furthermore, an E-M algorithm is developed for estimating the partial map and recovering the latent sharp image alternatively. Experimental results show that our partial deconvolution model is effective in relieving artifacts caused by inaccurate blur kernel, and can achieve favorable deblurring quality on synthetic and real blurry images.Most non-blind deconvolution methods are developed under the error-free kernel assumption, and are not robust to inaccurate blur kernel. Unfortunately, despite the great progress in blind deconvolution, estimation error remains inevitable during blur kernel estimation. Consequently, severe artifacts such as ringing effects and distortions are likely to be introduced in the non-blind deconvolution stage. In this paper, we tackle this issue by suggesting: (i) a partial map in the Fourier domain for modeling kernel estimation error, and (ii) a partial deconvolution model for robust deblurring with inaccurate blur kernel. The partial map is constructed by detecting the reliable Fourier entries of estimated blur kernel. And partial deconvolution is applied to wavelet-based and learning

Heterogeneous kinetic modeling of the catalytic conversion of cycloparaffins

Science.gov (United States)

Al-Sabawi, Mustafa N.

The limited availability of high value light hydrocarbon feedstocks along with the rise in crude prices has resulted in the international recognition of the vast potential of Canada's oil sands. With the recent expansion of Canadian bitumen production come, however, many technical challenges, one of which is the significant presence of aromatics and cycloparaffins in bitumen-derived feedstocks. In addition to their negative environmental impact, aromatics limit fluid catalytic cracking (FCC) feedstock conversion, decrease the yield and quality of valuable products such as gasoline and middle distillates, increase levels of polyaromatic hydrocarbons prone to form coke on the catalyst, and ultimately compromise the FCC unit performance. Although cycloparaffins do not have such negative impacts, they are precursors of aromatics as they frequently undergo hydrogen transfer reactions. However, cycloparaffin cracking chemistry involves other competing reactions that are complex and need much investigation. This dissertation provides insights and understanding of the fundamentals of the catalytic cracking of cycloparaffins using carefully selected model compounds such as methylcyclohexane (MCH) and decalin. Thermal and catalytic cracking of these cycloparaffins on FCC-type catalysts are carried out using the CREC Riser Simulator under operating conditions similar to those of the industrial FCC units in terms of temperature, reaction time, reactant partial pressure and catalyst-to-hydrocarbon ratio. The crystallite size of the supported zeolites is varied between 0.4 and 0.9 microns, with both activity and selectivity being monitored. Catalytic conversions ranged between 4 to 16 wt% for MCH and between 8 to 27 wt% for decalin. Reaction pathways of cycloparaffins are determined, and these include ring-opening, protolytic cracking, isomerization, hydrogen transfer and transalkylation. The yields and selectivities of over 60 and 140 products, formed during MCH and decalin

A new non-catalytic role for ubiquitin ligase RNF8 in unfolding higher-order chromatin structure

DEFF Research Database (Denmark)

Luijsterburg, Martijn S; Acs, Klara; Ackermann, Leena

2012-01-01

The ubiquitin ligases RNF8 and RNF168 orchestrate DNA damage signalling through the ubiquitylation of histone H2A and the recruitment of downstream repair factors. Here, we demonstrate that RNF8, but not RNF168 or the canonical H2A ubiquitin ligase RNF2, mediates extensive chromatin decondensation....... Our data show that CHD4, the catalytic subunit of the NuRD complex, interacts with RNF8 and is essential for RNF8-mediated chromatin unfolding. The chromatin remodelling activity of CHD4 promotes efficient ubiquitin conjugation and assembly of RNF168 and BRCA1 at DNA double-strand breaks....... Interestingly, RNF8-mediated recruitment of CHD4 and subsequent chromatin remodelling were independent of the ubiquitin-ligase activity of RNF8, but involved a non-canonical interaction with the forkhead-associated (FHA) domain. Our study reveals a new mechanism of chromatin remodelling-assisted ubiquitylation...

On the nanostructuring and catalytic promotion of intermediate temperature solid oxide fuel cell (IT-SOFC) cathodes

Science.gov (United States)

Serra, José M.; Buchkremer, Hans-Peter

Solid oxide fuel cells (SOFCs) are highly efficient energy converters for both stationary and mobile purposes. However, their market introduction still demands the reduction of manufacture costs and one possible way to reach this goal is the decrease of the operating temperatures, which entails the improvement of the cathode electrocatalytic properties. An ideal cathode material may have mixed ionic and electronic conductivity as well as proper catalytic properties. Nanostructuring and catalytic promotion of mixed conducting perovskites (e.g. La 0.58Sr 0.4Fe 0.8Co 0.2O 3- δ) seem to be promising approaches to overcoming cathode polarization problems and are briefly illustrated here. The preparation of nanostructured cathodes with relatively high surface area and enough thermal stability enables to improve the oxygen exchange rate and therefore the overall SOFC performance. A similar effect was obtained by catalytic promoting the perovskite surface, allowing decoupling the catalytic and ionic-transport properties in the cathode design. Noble metal incorporation may improve the reversibility of the reduction cycles involved in the oxygen reduction. Under the cathode oxidizing conditions, Pd seems to be partially dissolved in the perovskite structure and as a result very well dispersed.

Effect of surface composition of yttrium-stabilized zirconia on partial oxidation of methane to synthesis gas.

NARCIS (Netherlands)

Zhu, J.J.; van Ommen, J.G.; Knoester, A.; Lefferts, Leonardus

2005-01-01

Catalytic partial oxidation of methane to synthesis gas (CPOM) over yttrium-stabilized zirconia (YSZ) was studied within a wide temperature window (500¿1100 °C). The catalysts were characterized by X-ray fluorescence (XRF) and low-energy ion scattering (LEIS). The influence of calcination

Catalytic distillation process

Science.gov (United States)

Smith, L.A. Jr.

1982-06-22

A method is described for conducting chemical reactions and fractionation of the reaction mixture comprising feeding reactants to a distillation column reactor into a feed zone and concurrently contacting the reactants with a fixed bed catalytic packing to concurrently carry out the reaction and fractionate the reaction mixture. For example, a method for preparing methyl tertiary butyl ether in high purity from a mixed feed stream of isobutene and normal butene comprising feeding the mixed feed stream to a distillation column reactor into a feed zone at the lower end of a distillation reaction zone, and methanol into the upper end of said distillation reaction zone, which is packed with a properly supported cationic ion exchange resin, contacting the C[sub 4] feed and methanol with the catalytic distillation packing to react methanol and isobutene, and concurrently fractionating the ether from the column below the catalytic zone and removing normal butene overhead above the catalytic zone.

A review of carbon-based and non-carbon-based catalyst supports for the selective catalytic reduction of nitric oxide.

Science.gov (United States)

Anthonysamy, Shahreen Binti Izwan; Afandi, Syahidah Binti; Khavarian, Mehrnoush; Mohamed, Abdul Rahman Bin

2018-01-01

Various types of carbon-based and non-carbon-based catalyst supports for nitric oxide (NO) removal through selective catalytic reduction (SCR) with ammonia are examined in this review. A number of carbon-based materials, such as carbon nanotubes (CNTs), activated carbon (AC), and graphene (GR) and non-carbon-based materials, such as Zeolite Socony Mobil-5 (ZSM-5), TiO 2 , and Al 2 O 3 supported materials, were identified as the most up-to-date and recently used catalysts for the removal of NO gas. The main focus of this review is the study of catalyst preparation methods, as this is highly correlated to the behaviour of NO removal. The general mechanisms involved in the system, the Langmuir-Hinshelwood or Eley-Riedeal mechanism, are also discussed. Characterisation analysis affecting the surface and chemical structure of the catalyst is also detailed in this work. Finally, a few major conclusions are drawn and future directions for work on the advancement of the SCR-NH 3 catalyst are suggested.

Catalytic Combustion of Gasified Waste

Energy Technology Data Exchange (ETDEWEB)

Kusar, Henrik

2003-09-01

This thesis concerns catalytic combustion for gas turbine application using a low heating-value (LHV) gas, derived from gasified waste. The main research in catalytic combustion focuses on methane as fuel, but an increasing interest is directed towards catalytic combustion of LHV fuels. This thesis shows that it is possible to catalytically combust a LHV gas and to oxidize fuel-bound nitrogen (NH{sub 3}) directly into N{sub 2} without forming NO{sub x} The first part of the thesis gives a background to the system. It defines waste, shortly describes gasification and more thoroughly catalytic combustion. The second part of the present thesis, paper I, concerns the development and testing of potential catalysts for catalytic combustion of LHV gases. The objective of this work was to investigate the possibility to use a stable metal oxide instead of noble metals as ignition catalyst and at the same time reduce the formation of NO{sub x} In paper II pilot-scale tests were carried out to prove the potential of catalytic combustion using real gasified waste and to compare with the results obtained in laboratory scale using a synthetic gas simulating gasified waste. In paper III, selective catalytic oxidation for decreasing the NO{sub x} formation from fuel-bound nitrogen was examined using two different approaches: fuel-lean and fuel-rich conditions. Finally, the last part of the thesis deals with deactivation of catalysts. The various deactivation processes which may affect high-temperature catalytic combustion are reviewed in paper IV. In paper V the poisoning effect of low amounts of sulfur was studied; various metal oxides as well as supported palladium and platinum catalysts were used as catalysts for combustion of a synthetic gas. In conclusion, with the results obtained in this thesis it would be possible to compose a working catalytic system for gas turbine application using a LHV gas.

Catalytic properties of lanthanide amide, imide and nitride formed by thermal degradation of liquid ammonia solutions of Eu and Yb metal

International Nuclear Information System (INIS)

Imamura, H.; Mizuno, K.; Ohishi, K.; Suda, E.; Kanda, K.; Sakata, Y.; Tsuchiya, S.

1998-01-01

The catalytic properties of lanthanide amide, imide and nitride prepared by the use of liquid ammonia solutions of lanthanide metals (Ln=Eu and Yb) were studied for catalytic hydrogenation. The reaction of Eu or Yb metal solutions in liquid ammonia with silica yielded SiO 2 -grafted lanthanide amide in the divalent state. The divalent amide showed catalytic activity for the selective hydrogenation of dienes and benzene. It was found that partial hydrogenation of benzene occurred with a very high selectivity for cyclohexene. Amides of calcium, strontium and barium were examined similarly in connection with catalytic studies on divalent amides. Imide and nitride, into which the lanthanide (Ln/AC) deposited by impregnation of active carbon (AC) with liquid ammonia solutions of lanthanide metals were converted thermally, were studied catalytically. It was concluded that imide or imide-like species generated during the thermal degradation of lanthanide amide to nitride were very active in the hydrogenation of ethene. Lanthanide nitride was virtually inactive, but the nitride highly dispersed on active carbon was activated when subjected to evacuation treatment above about 1000 K. (orig.)

Catalytic ozonation of fenofibric acid over alumina-supported manganese oxide

Energy Technology Data Exchange (ETDEWEB)

Rosal, Roberto, E-mail: roberto.rosal@uah.es [Departamento de Quimica Analitica e Ingenieria Quimica, Universidad de Alcala, E-28771 Alcala de Henares (Spain); Gonzalo, Maria S.; Rodriguez, Antonio; Garcia-Calvo, Eloy [Departamento de Quimica Analitica e Ingenieria Quimica, Universidad de Alcala, E-28771 Alcala de Henares (Spain)

2010-11-15

The catalytic ozonation of fenofibric acid was studied using activated alumina and alumina-supported manganese oxide in a semicontinuous reactor. The rate constants at 20 deg. C for the non-catalytic reaction of fenofibric acid with ozone and hydroxyl radicals were 3.43 {+-} 0.20 M{sup -1} s{sup -1} and (6.55 {+-} 0.33) x 10{sup 9} M{sup -1} s{sup -1}, respectively. The kinetic constant for the catalytic reaction between fenofibric acid and hydroxyl radicals did not differ significantly from that of homogeneous ozonation, either using Al{sub 2}O{sub 3} or MnO{sub x}/Al{sub 2}O{sub 3}. The results showed a considerable increase in the generation of hydroxyl radicals due to the use of catalysts even in the case of catalytic runs performed using a real wastewater matrix. Both catalysts promoted the decomposition of ozone in homogeneous phase, but the higher production of hydroxyl radicals corresponded to the catalyst with more activity in terms of ozone decomposition. We did not find evidence of the catalysts having any effect on rate constants, which suggests that the reaction may not involve the adsorption of organics on catalyst surface.

Fuel rich and fuel lean catalytic combustion of the stabilized confined turbulent gaseous diffusion flames over noble metal disc burners

Directory of Open Access Journals (Sweden)

Amal S. Zakhary

2014-03-01

Full Text Available Catalytic combustion of stabilized confined turbulent gaseous diffusion flames using Pt/Al2O3 and Pd/Al2O3 disc burners situated in the combustion domain under both fuel-rich and fuel-lean conditions was experimentally studied. Commercial LPG fuel having an average composition of: 23% propane, 76% butane, and 1% pentane was used. The thermal structure of these catalytic flames developed over Pt/Al2O3 and Pd/Al2O3 burners were examined via measuring the mean temperature distribution in the radial direction at different axial locations along the flames. Under-fuel-rich condition the flames operated over Pt catalytic disc attained high temperature values in order to express the progress of combustion and were found to achieve higher activity as compared to the flames developed over Pd catalytic disc. These two types of catalytic flames demonstrated an increase in the reaction rate with the downstream axial distance and hence, an increase in the flame temperatures was associated with partial oxidation towards CO due to the lack of oxygen. However, under fuel-lean conditions the catalytic flame over Pd catalyst recorded comparatively higher temperatures within the flame core in the near region of the main reaction zone than over Pt disc burner. These two catalytic flames over Pt and Pd disc burners showed complete oxidation to CO2 since the catalytic surface is covered by more rich oxygen under the fuel-lean condition.

Catalytic steam reforming of ethanol for hydrogen production: Brief status

Directory of Open Access Journals (Sweden)

Bineli Aulus R.R.

2016-01-01

Full Text Available Hydrogen represents a promising fuel since it is considered as a cleanest energy carrier and also because during its combustion only water is emitted. It can be produced from different kinds of renewable feedstocks, such as ethanol, in this sense hydrogen could be treated as biofuel. Three chemical reactions can be used to achieve this purpose: the steam reforming (SR, the partial oxidation (POX and the autothermal reforming (ATR. In this study, the catalysts implemented in steam reforming of ethanol were reviewed. A wide variety of elements can be used as catalysts for this reaction, such as base metals (Ni, Cu and Co or noble metals (Rh, Pt and Ru usually deposited on a support material that increases surface area and improves catalytic function. The use of Rh, Ni and Pt supported or promoted with CeO2, and/or La2O3 shows excellent performance in ethanol SR catalytic process. The ratio of water to ethanol, reaction temperatures, catalysts loadings, selectivity and activity are also discussed as they are extremely important for high hydrogen yields.

Non-periodic pseudo-random numbers used in Monte Carlo calculations

Science.gov (United States)

Barberis, Gaston E.

2007-09-01

The generation of pseudo-random numbers is one of the interesting problems in Monte Carlo simulations, mostly because the common computer generators produce periodic numbers. We used simple pseudo-random numbers generated with the simplest chaotic system, the logistic map, with excellent results. The numbers generated in this way are non-periodic, which we demonstrated for 1013 numbers, and they are obtained in a deterministic way, which allows to repeat systematically any calculation. The Monte Carlo calculations are the ideal field to apply these numbers, and we did it for simple and more elaborated cases. Chemistry and Information Technology use this kind of simulations, and the application of this numbers to quantum Monte Carlo and cryptography is immediate. I present here the techniques to calculate, analyze and use these pseudo-random numbers, show that they lack periodicity up to 1013 numbers and that they are not correlated.

Non-periodic pseudo-random numbers used in Monte Carlo calculations

International Nuclear Information System (INIS)

Barberis, Gaston E.

2007-01-01

The generation of pseudo-random numbers is one of the interesting problems in Monte Carlo simulations, mostly because the common computer generators produce periodic numbers. We used simple pseudo-random numbers generated with the simplest chaotic system, the logistic map, with excellent results. The numbers generated in this way are non-periodic, which we demonstrated for 10 13 numbers, and they are obtained in a deterministic way, which allows to repeat systematically any calculation. The Monte Carlo calculations are the ideal field to apply these numbers, and we did it for simple and more elaborated cases. Chemistry and Information Technology use this kind of simulations, and the application of this numbers to quantum Monte Carlo and cryptography is immediate. I present here the techniques to calculate, analyze and use these pseudo-random numbers, show that they lack periodicity up to 10 13 numbers and that they are not correlated

Synthesis, characterization and catalytic properties of nanocrystaline Y2O3-coated TiO2 in the ethanol dehydration reaction

International Nuclear Information System (INIS)

Fajardo, Humberto Vieira; Longo, Elson; Leite, Edson Roberto; Libanori, Rafael; Probst, Luiz Fernando Dias; Carreno, Neftali Lenin Villarreal

2012-01-01

In the present study, TiO 2 nano powder was partially coated with Y 2 O 3 precursors generated by a sol-gel modified route. The system of nanocoated particles formed an ultra thin structure on the TiO 2 surfaces. The modified nanoparticles were characterized by high resolution transmission electron microscopy (HR-TEM), X-ray diffraction (XRD) analysis, Zeta potential and surface area through N 2 physisorption measurements. Bioethanol dehydration was used as a probe reaction to investigate the modifications on the nanoparticles surface. The process led to the obtainment of nanoparticles with important surface characteristics and catalytic behavior in the bioethanol dehydration reaction, with improved activity and particular selectivity in comparison to their non-coated analogs. The ethylene production was disfavored and selectivity toward acetaldehyde, hydrogen and ethane increased over modified nanoparticles. (author)

Catalytic bioreactors and methods of using same

Science.gov (United States)

Worden, Robert Mark; Liu, Yangmu Chloe

2017-07-25

Various embodiments provide a bioreactor for producing a bioproduct comprising one or more catalytically active zones located in a housing and adapted to keep two incompatible gaseous reactants separated when in a gas phase, wherein each of the one or more catalytically active zones may comprise a catalytic component retainer and a catalytic component retained within and/or thereon. Each of the catalytically active zones may additionally or alternatively comprise a liquid medium located on either side of the catalytic component retainer. Catalytic component may include a microbial cell culture located within and/or on the catalytic component retainer, a suspended catalytic component suspended in the liquid medium, or a combination thereof. Methods of using various embodiments of the bioreactor to produce a bioproduct, such as isobutanol, are also provided.

Investigation of the Origin of Catalytic Activity in Oxide-Supported Nanoparticle Gold

Energy Technology Data Exchange (ETDEWEB)

Harrison, Ian [Univ. of Virginia, Charlottesville, VA (United States)

2017-05-26

Since Haruta’s discovery in 1987 of the surprising catalytic activity of supported Au nanoparticles, we have seen a very large number of experimental and theoretical efforts to explain this activity and to fully understand the nature of the behavior of the responsible active sites. In 2011, we discovered that a dual catalytic site at the perimeter of ~3nm diameter Au particles supported on TiO₂ is responsible for oxidative catalytic activity. O₂ molecules bind with Au atoms and Ti4+ ions in the TiO₂ support and the weakened O-O bond dissociates at low temperatures, proceeding to produce O atoms which act as oxidizing agents for the test molecule, CO. The papers supported by DOE have built on this finding and have been concerned with two aspects of the behavior of Au/TiO₂ catalysts: (1). Mechanistic behavior of dual catalytic sites in the oxidation of organic molecules such as ethylene and acetic acid; (2). Studies of the electronic properties of the TiO₂ (110) single crystal in relation to its participation in charge transfer at the occupied dual catalytic site. A total of 20 papers have been produced through DOE support of this work. The papers combine IR spectroscopic investigations of Au/TiO₂ catalysts with surface science on the TiO₂(110) and TiO₂ nanoparticle surfaces with modern density functional modeling. The primary goals of the work were to investigate the behavior of the dual Au/Ti⁴⁺ site for the partial oxidation of alcohols to acids, the hydrogenation of aldehydes and ketones to alcohols, and the condensation of oxygenate intermediates- all processes related to the utilization of biomass in the production of useful chemical energy sources.

A non-catalytic histidine residue influences the function of the metalloprotease of Listeria monocytogenes.

Science.gov (United States)

Forster, Brian M; Bitar, Alan Pavinski; Marquis, Hélène

2014-01-01

Mpl, a thermolysin-like metalloprotease, and PC-PLC, a phospholipase C, are synthesized as proenzymes by the intracellular bacterial pathogen Listeria monocytogenes. During intracellular growth, L. monocytogenes is temporarily confined in a membrane-bound vacuole whose acidification leads to Mpl autolysis and Mpl-mediated cleavage of the PC-PLC N-terminal propeptide. Mpl maturation also leads to the secretion of both Mpl and PC-PLC across the bacterial cell wall. Previously, we identified negatively charged and uncharged amino acid residues within the N terminus of the PC-PLC propeptide that influence the ability of Mpl to mediate the maturation of PC-PLC, suggesting that these residues promote the interaction of the PC-PLC propeptide with Mpl. In the present study, we identified a non-catalytic histidine residue (H226) that influences Mpl secretion across the cell wall and its ability to process PC-PLC. Our results suggest that a positive charge at position 226 is required for Mpl functions other than autolysis. Based on the charge requirement at this position, we hypothesize that this residue contributes to the interaction of Mpl with the PC-PLC propeptide.

A non-parametric test for partial monotonicity in multiple regression

NARCIS (Netherlands)

van Beek, M.; Daniëls, H.A.M.

Partial positive (negative) monotonicity in a dataset is the property that an increase in an independent variable, ceteris paribus, generates an increase (decrease) in the dependent variable. A test for partial monotonicity in datasets could (1) increase model performance if monotonicity may be

Combustion of hydrogen-air in micro combustors with catalytic Pt layer

Energy Technology Data Exchange (ETDEWEB)

Yang Wang; Zhijun Zhou; Weijuan Yang; Junhu Zhou; Jianzhong Liu; Zhihua Wang; Cen, Kefa [State Key Laboratory of Clean Energy Utilization, Zhejiang University, Hangzhou 310027, Zhejiang (China)

2010-06-15

Micro power generators have high power density. However, their key components micro combustors have low stability. In this experiment, catalyst is applied to improve the stability. The catalytic micro combustor is made from an alumina ceramic tube. It has inner diameter of 1 mm, outer diameter of 2.02 mm and length of 24.5 mm. It is prepared through impregnation of aqueous solution of H{sub 2}PtCl{sub 6}. The flammability limits and surface temperatures under different operation conditions are measured. The flow rates range from 0.08 to 0.4 L/min. According to the experimental results, catalyst is effective to inhibit extinction. For example, At 0.8 L/min, the stability limit is 0.193-14.9 in the non-catalytic combustor. After applying catalyst, the lean limit is near 0, and the rich limit is 29.3. But catalyst is less effective to inhibit blow out. Increasing flow rates also inhibits extinction. In the non-catalytic combustor, while the flow rates increase from 0.08 to 0.2 L/min, the lean stability limit decreases from 0.193 to 0.125. The experimental results indicate that catalyst induces shift downstream in the stoichiometric and rich cases. The numeric simulation verifies that the heterogeneous reaction weakens the homogeneous reaction through consuming fuels. Thus, the insufficient heat recirculation makes the reaction region shift downstream. However, lean mixture has intense reaction in the catalytic combustor. It is attributed to the high mass diffusion and low thermal diffusion of lean mixture. (author)

Combustion of hydrogen-air in micro combustors with catalytic Pt layer

Energy Technology Data Exchange (ETDEWEB)

Wang Yang; Zhou Zhijun [State Key Laboratory of Clean Energy Utilization, Zhejiang University, Hangzhou 310027, Zhejiang (China); Yang Weijuan, E-mail: 10508107@zju.edu.c [State Key Laboratory of Clean Energy Utilization, Zhejiang University, Hangzhou 310027, Zhejiang (China); Zhou Junhu; Liu Jianzhong; Wang Zhihua; Cen Kefa [State Key Laboratory of Clean Energy Utilization, Zhejiang University, Hangzhou 310027, Zhejiang (China)

2010-06-15

Micro power generators have high power density. However, their key components micro combustors have low stability. In this experiment, catalyst is applied to improve the stability. The catalytic micro combustor is made from an alumina ceramic tube. It has inner diameter of 1 mm, outer diameter of 2.02 mm and length of 24.5 mm. It is prepared through impregnation of aqueous solution of H{sub 2}PtCl{sub 6}. The flammability limits and surface temperatures under different operation conditions are measured. The flow rates range from 0.08 to 0.4 L/min. According to the experimental results, catalyst is effective to inhibit extinction. For example, At 0.8 L/min, the stability limit is 0.193-14.9 in the non-catalytic combustor. After applying catalyst, the lean limit is near 0, and the rich limit is 29.3. But catalyst is less effective to inhibit blow out. Increasing flow rates also inhibits extinction. In the non-catalytic combustor, while the flow rates increase from 0.08 to 0.2 L/min, the lean stability limit decreases from 0.193 to 0.125. The experimental results indicate that catalyst induces shift downstream in the stoichiometric and rich cases. The numeric simulation verifies that the heterogeneous reaction weakens the homogeneous reaction through consuming fuels. Thus, the insufficient heat recirculation makes the reaction region shift downstream. However, lean mixture has intense reaction in the catalytic combustor. It is attributed to the high mass diffusion and low thermal diffusion of lean mixture.

Combustion of hydrogen-air in micro combustors with catalytic Pt layer

International Nuclear Information System (INIS)

Wang Yang; Zhou Zhijun; Yang Weijuan; Zhou Junhu; Liu Jianzhong; Wang Zhihua; Cen Kefa

2010-01-01

Micro power generators have high power density. However, their key components micro combustors have low stability. In this experiment, catalyst is applied to improve the stability. The catalytic micro combustor is made from an alumina ceramic tube. It has inner diameter of 1 mm, outer diameter of 2.02 mm and length of 24.5 mm. It is prepared through impregnation of aqueous solution of H 2 PtCl 6 . The flammability limits and surface temperatures under different operation conditions are measured. The flow rates range from 0.08 to 0.4 L/min. According to the experimental results, catalyst is effective to inhibit extinction. For example, At 0.8 L/min, the stability limit is 0.193-14.9 in the non-catalytic combustor. After applying catalyst, the lean limit is near 0, and the rich limit is 29.3. But catalyst is less effective to inhibit blow out. Increasing flow rates also inhibits extinction. In the non-catalytic combustor, while the flow rates increase from 0.08 to 0.2 L/min, the lean stability limit decreases from 0.193 to 0.125. The experimental results indicate that catalyst induces shift downstream in the stoichiometric and rich cases. The numeric simulation verifies that the heterogeneous reaction weakens the homogeneous reaction through consuming fuels. Thus, the insufficient heat recirculation makes the reaction region shift downstream. However, lean mixture has intense reaction in the catalytic combustor. It is attributed to the high mass diffusion and low thermal diffusion of lean mixture.

Influence of partially known parameter on flaw characterization in Eddy Current Testing by using a random walk MCMC method based on metamodeling

International Nuclear Information System (INIS)

Cai, Caifang; Lambert, Marc; Rodet, Thomas

2014-01-01

First, we present the implementation of a random walk Metropolis-within-Gibbs (MWG) sampling method in flaw characterization based on a metamodeling method. The role of metamodeling is to reduce the computational time cost in Eddy Current Testing (ECT) forward model calculation. In such a way, the use of Markov Chain Monte Carlo (MCMC) methods becomes possible. Secondly, we analyze the influence of partially known parameters in Bayesian estimation. The objective is to evaluate the importance of providing more specific prior information. Simulation results show that even partially known information has great interest in providing more accurate flaw parameter estimations. The improvement ratio depends on the parameter dependence and the interest shows only when the provided information is specific enough

Predicting CYP2C19 Catalytic Parameters for Enantioselective Oxidations Using Artificial Neural Networks and a Chirality Code

Science.gov (United States)

Hartman, Jessica H.; Cothren, Steven D.; Park, Sun-Ha; Yun, Chul-Ho; Darsey, Jerry A.; Miller, Grover P.

2013-01-01

Cytochromes P450 (CYP for isoforms) play a central role in biological processes especially metabolism of chiral molecules; thus, development of computational methods to predict parameters for chiral reactions is important for advancing this field. In this study, we identified the most optimal artificial neural networks using conformation-independent chirality codes to predict CYP2C19 catalytic parameters for enantioselective reactions. Optimization of the neural networks required identifying the most suitable representation of structure among a diverse array of training substrates, normalizing distribution of the corresponding catalytic parameters (kcat, Km, and kcat/Km), and determining the best topology for networks to make predictions. Among different structural descriptors, the use of partial atomic charges according to the CHelpG scheme and inclusion of hydrogens yielded the most optimal artificial neural networks. Their training also required resolution of poorly distributed output catalytic parameters using a Box-Cox transformation. End point leave-one-out cross correlations of the best neural networks revealed that predictions for individual catalytic parameters (kcat and Km) were more consistent with experimental values than those for catalytic efficiency (kcat/Km). Lastly, neural networks predicted correctly enantioselectivity and comparable catalytic parameters measured in this study for previously uncharacterized CYP2C19 substrates, R- and S-propranolol. Taken together, these seminal computational studies for CYP2C19 are the first to predict all catalytic parameters for enantioselective reactions using artificial neural networks and thus provide a foundation for expanding the prediction of cytochrome P450 reactions to chiral drugs, pollutants, and other biologically active compounds. PMID:23673224

Catalytic process for tritium exchange reaction

International Nuclear Information System (INIS)

Hansoo Lee; Kang, H.S.; Paek, S.W.; Hongsuk Chung; Yang Geun Chung; Sook Kyung Lee

2001-01-01

The catalytic activities for a hydrogen isotope exchange were measured through the reaction of a vapor and gas mixture. The catalytic activity showed to be comparable with the published data. Since the gas velocity is relatively low, the deactivation was not found clearly during the 5-hour experiment. Hydrogen isotope transfer experiments were also conducted through the liquid phase catalytic exchange reaction column that consisted of a catalytic bed and a hydrophilic bed. The efficiencies of both the catalytic and hydrophilic beds were higher than 0.9, implying that the column performance was excellent. (author)

Topical silver sulfadiazine vs collagenase ointment for the treatment of partial thickness burns in children: a prospective randomized trial.

Science.gov (United States)

Ostlie, Daniel J; Juang, David; Aguayo, Pablo; Pettiford-Cunningham, Janine P; Erkmann, Erin A; Rash, Diane E; Sharp, Susan W; Sharp, Ronald J; St Peter, Shawn D

2012-06-01

The 2 most commonly used topical agents for partial thickness burns are silver sulfadiazine (SSD) and collagenase ointment (CO). Silver sulfadiazine holds antibacterial properties, and eschar separation occurs naturally. Collagenase ointment is an enzyme that cleaves denatured collagen facilitating separation but has no antibacterial properties. Currently, there are no prospective comparative data in children for these 2 agents. Therefore, we conducted a prospective randomized trial. After institutional review board approval, patients were randomized to daily debridement with SSD or CO. Primary outcome was the need for skin grafting. Patients were treated for 2 days with SSD with subsequent randomization. Polymyxin was mixed with CO for antibacterial coverage. Debridements were performed daily for 10 days or until the burn healed. Grafting was performed after 10 days if not healed. From January 2008 to January 2011, 100 patients were enrolled, with no differences in patient characteristics. There were no differences in clinical course, outcome, or need for skin grafting. Wound infections occurred in 7 patients treated with CO and 1 patient treated with SSD (P = .06). Collagenase ointment was more expensive than SSD (P burns results. Copyright © 2012 Elsevier Inc. All rights reserved.

One-step partial or complete caries removal and bonding with antibacterial or traditional self-etch adhesives: study protocol for a randomized controlled trial.

Science.gov (United States)

Villat, Cyril; Attal, Jean-Pierre; Brulat, Nathalie; Decup, Franck; Doméjean, Sophie; Dursun, Elisabeth; Fron-Chabouis, Hélène; Jacquot, Bruno; Muller Bolla, Michèle; Plasse-Pradelle, Nelly; Roche, Laurent; Maucort-Boulch, Delphine; Nony, Patrice; Gritsch, Kerstin; Millet, Pierre; Gueyffier, François; Grosgogeat, Brigitte

2016-08-15

Current concepts in conservative dentistry advocate minimally invasive dentistry and pulp vitality preservation. Moreover, complete removal of carious dentin in deep carious lesions often leads to pulp exposure and root canal treatment, despite the absence of irreversible pulp inflammation. For years, partial caries removal has been performed on primary teeth, but little evidence supports its effectiveness for permanent teeth. Furthermore, the recent development of new antibacterial adhesive systems could be interesting in the treatment of such lesions. The objectives of this study are to compare the effectiveness of partial versus complete carious dentin removal in deep lesions (primary objective) and the use of an antibacterial versus a traditional two-step self-etch adhesive system (main secondary objective). The DEep CAries Treatment (DECAT) study protocol is a multicenter, randomized, controlled superiority trial comparing partial versus complete caries removal followed by adhesive restoration. The minimum sample size required is 464 patients. Two successive randomizations will be performed (allocation ratio 1:1): the first for the type of excavation (partial versus complete) and the second (if no root canal treatment is required) for the type of adhesive (antibacterial versus traditional). For the two objectives, the outcome is the success of the treatment after 1 year, measured according to a composite outcome of five FDI criteria: material fracture and retention, marginal adaptation, radiographic examination (including apical pathologies), postoperative sensitivity and tooth vitality, and carious lesion recurrence. The study will investigate the interest of a conservative approach for the management of deep carious lesions in terms of dentin excavation and bioactive adhesive systems. The results may help practitioners achieve the most efficient restorative procedure to maintain pulp vitality and increase the restoration longevity. Clinical

Non-surgical treatment of lateral epicondylitis: a systematic review of randomized controlled trials.

Science.gov (United States)

Sims, Susan E G; Miller, Katherine; Elfar, John C; Hammert, Warren C

2014-12-01

Non-surgical approaches to treatment of lateral epicondylitis are numerous. The aim of this systematic review is to examine randomized, controlled trials of these treatments. Numerous databases were systematically searched from earliest records to February 2013. Search terms included "lateral epicondylitis," "lateral elbow pain," "tennis elbow," "lateral epicondylalgia," and "elbow tendinopathy" combined with "randomized controlled trial." Two reviewers examined the literature for eligibility via article abstract and full text. Fifty-eight articles met eligibility criteria: (1) a target population of patients with symptoms of lateral epicondylitis; (2) evaluation of treatment of lateral epicondylitis with the following non-surgical techniques: corticosteroid injection, injection technique, iontophoresis, botulinum toxin A injection, prolotherapy, platelet-rich plasma or autologous blood injection, bracing, physical therapy, shockwave therapy, or laser therapy; and (3) a randomized controlled trial design. Lateral epicondylitis is a condition that is usually self-limited. There may be a short-term pain relief advantage found with the application of corticosteroids, but no demonstrable long-term pain relief. Injection of botulinum toxin A and prolotherapy are superior to placebo but not to corticosteroids, and botulinum toxin A is likely to produce concomitant extensor weakness. Platelet-rich plasma or autologous blood injections have been found to be both more and less effective than corticosteroid injections. Non-invasive treatment methods such as bracing, physical therapy, and extracorporeal shockwave therapy do not appear to provide definitive benefit regarding pain relief. Some studies of low-level laser therapy show superiority to placebo whereas others do not. There are multiple randomized controlled trials for non-surgical management of lateral epicondylitis, but the existing literature does not provide conclusive evidence that there is one preferred method

A Bioinspired Catalytic Aerobic Oxidative C–H Functionalization of Primary Aliphatic Amines: Synthesis of 1,2-Disubstituted Benzimidazoles

Science.gov (United States)

Nguyen, Khac Minh Huy; Largeron, Martine

2015-01-01

Aerobic oxidative C–H functionalization of primary aliphatic amines has been accomplished with a biomimetic cooperative catalytic system to furnish 1,2-disubstituted benzimidazoles that play an important role as drug discovery targets. This one-pot atom-economical multistep process, which proceeds under mild conditions, with ambient air and equimolar amounts of each coupling partner, constitutes a convenient environmentally friendly strategy to functionalize non-activated aliphatic amines that remain challenging substrates for non-enzymatic catalytic aerobic systems. PMID:26206475

Contributions to the theory of catalytic titrations-III Neutralization catalytic titrations.

Science.gov (United States)

Gaál, F F; Abramović, B F

1985-07-01

Neutralization catalytic titrations of weak monoprotic adds and bases with both volumetric and coulometric addition of the titrant (strong base/acid) have been simulated by taking into account the equilibrium concentration of the catalyst during the titration. The influence of several factors on the shape of the simulated catalytic titration curve has been investigated and is discussed.

Characterisation of random Gaussian and non-Gaussian stress processes in terms of extreme responses

Directory of Open Access Journals (Sweden)

Colin Bruno

2015-01-01

Full Text Available In the field of military land vehicles, random vibration processes generated by all-terrain wheeled vehicles in motion are not classical stochastic processes with a stationary and Gaussian nature. Non-stationarity of processes induced by the variability of the vehicle speed does not form a major difficulty because the designer can have good control over the vehicle speed by characterising the histogram of instantaneous speed of the vehicle during an operational situation. Beyond this non-stationarity problem, the hard point clearly lies in the fact that the random processes are not Gaussian and are generated mainly by the non-linear behaviour of the undercarriage and the strong occurrence of shocks generated by roughness of the terrain. This non-Gaussian nature is expressed particularly by very high flattening levels that can affect the design of structures under extreme stresses conventionally acquired by spectral approaches, inherent to Gaussian processes and based essentially on spectral moments of stress processes. Due to these technical considerations, techniques for characterisation of random excitation processes generated by this type of carrier need to be changed, by proposing innovative characterisation methods based on time domain approaches as described in the body of the text rather than spectral domain approaches.

Suppression of thermal noise in a non-Markovian random velocity field

International Nuclear Information System (INIS)

Ueda, Masahiko

2016-01-01

We study the diffusion of Brownian particles in a Gaussian random velocity field with short memory. By extending the derivation of an effective Fokker–Planck equation for the Lanvegin equation with weakly colored noise to a random velocity-field problem, we find that the effect of thermal noise on particles is suppressed by the existence of memory. We also find that the renormalization effect for the relative diffusion of two particles is stronger than that for single-particle diffusion. The results are compared with those of molecular dynamics simulations. (paper: classical statistical mechanics, equilibrium and non-equilibrium)

Partial-thickness burn wounds healing by topical treatment: A randomized controlled comparison between silver sulfadiazine and centiderm.

Science.gov (United States)

Saeidinia, Amin; Keihanian, Faeze; Lashkari, Ardalan Pasdaran; Lahiji, Hossein Ghavvami; Mobayyen, Mohammadreza; Heidarzade, Abtin; Golchai, Javad

2017-03-01

Burns are common event and associated with a high incidence of death, disability, and high costs. Centella asiatica (L.) is a medicinal herb, commonly growing in humid areas in several tropical countries that improve wound healing. On the basis of previous studies, we compared the efficacy of Centiderm versus silver sulfadiazine (SSD) in partial thickness burning patients. Study population comprised burn victims referred to Velayat Burning Hospital at Rasht, Iran. The intervention group received Centiderm and control group SSD cream. Burn wounds were treated once daily at home. All of the wounds were evaluated till complete healing occurred and at the admission, days 3, 7, 14 objective signs; visual acuity score (VAS) and subjective signs were recorded. Re-epithelialization time and complete healing days were recorded. We used random fixed block for randomization. The randomization sequence was created using the computer. Patients and burning specialist physician were blinded. Seventy-five patients randomized into 2 groups; (40 patients: Centiderm group; 35 patients: SSD group). The mean age of them was 30.67 ± 9.91 years and 19 of them were male (31.7%). Thirty patients in Centiderm and 30 patients in SSD group were analyzed. All of objective and subjective signs and mean of re-epithelialization and complete healing were significantly better in Centiderm group rather than SSD group (P < 0.05). There was no infection in Centiderm group. We showed that use of Centiderm ointment not only improved the objective and subjective signs in less than 3 days, but also the re-epithelialization and complete healing rather than SSD without any infection in the subjects.

Probing Structural and Catalytic Characteristics of Galactose Oxidase Confined in Nanoscale Chemical Environments

DEFF Research Database (Denmark)

Ikemoto, Hideki; Mossin, Susanne; Ulstrup, Jens

2014-01-01

Galactose oxidase (GAOX) is a special metalloenzyme in terms of its active site structure and catalytic mechanisms. This work reports a study where the enzyme confined in a nanoscale chemical environment provided by mesoporous silicas (MPS) is probed. Two types of MPS, i.e. SBA-15 and MCF, were...... synthesized and used to accommodate GAOX. SBA-15-ROD is rod-shaped particles with periodically ordered nanopores (9.5 nm), while MCF has a mesocellular foam-like structure with randomly distributed pores (23 nm) interconnected by smaller windows (8.8 nm). GAOX is non-covalently confined in SBA-15- ROD, while...... it is covalently immobilized in MCF. Relatively high loadings in the range of 50–60 mg g1 are achieved. Electron spin resonance (ESR) spectroscopy is used to probe the active site structures of the enzyme. The similar ESR spectra observed for GAOX in the free and immobilized states support that the electronic...

Random-walk enzymes

Science.gov (United States)

Mak, Chi H.; Pham, Phuong; Afif, Samir A.; Goodman, Myron F.

2015-09-01

Enzymes that rely on random walk to search for substrate targets in a heterogeneously dispersed medium can leave behind complex spatial profiles of their catalyzed conversions. The catalytic signatures of these random-walk enzymes are the result of two coupled stochastic processes: scanning and catalysis. Here we develop analytical models to understand the conversion profiles produced by these enzymes, comparing an intrusive model, in which scanning and catalysis are tightly coupled, against a loosely coupled passive model. Diagrammatic theory and path-integral solutions of these models revealed clearly distinct predictions. Comparison to experimental data from catalyzed deaminations deposited on single-stranded DNA by the enzyme activation-induced deoxycytidine deaminase (AID) demonstrates that catalysis and diffusion are strongly intertwined, where the chemical conversions give rise to new stochastic trajectories that were absent if the substrate DNA was homogeneous. The C →U deamination profiles in both analytical predictions and experiments exhibit a strong contextual dependence, where the conversion rate of each target site is strongly contingent on the identities of other surrounding targets, with the intrusive model showing an excellent fit to the data. These methods can be applied to deduce sequence-dependent catalytic signatures of other DNA modification enzymes, with potential applications to cancer, gene regulation, and epigenetics.

Possibility of increasing the average rate of heterogeneous catalytic reactions by operating in the self-oscillating regime

Energy Technology Data Exchange (ETDEWEB)

Chumakov, G A; Slinko, M G

1979-05-01

The possibility of increasing the average rate of heterogeneous catalytic reactions by operating in the self-oscillating regime was demonstrated by analyzing a kinetic model of hydrogen interaction with oxygen over a metallic catalyst. Within a certain interval of partial pressures of oxygen, the average reaction rate over a period of oscillation may be over five times that of the steady-state reaction.

Action des pots catalytiques sur les polluants non réglementés How Catalytic Mufflers Act on Unregulated Pollutants

Directory of Open Access Journals (Sweden)

Degobert P.

2006-11-01

Full Text Available L'installation de pots catalytiques sur les véhicules, envisagée essentiellement pour réduire le niveau des polluants actuellement réglementés (oxyde de carbone, hydrocarbures imbrûlés, oxydes d'azote, aura-t-elle des effets bénéfiques ou néfastes sur les polluants non réglementés ? Pour éclaircir cette question, cette étude compare sur des véhicules les plus comparables possibles du point de vue conception et équipements, les émissions des voitures non dépolluées et celles de voitures dépolluées , c'est-à-dire équipées de pots catalytiques d'oxydation, de pots catalytiques multifonctionnels ou de systèmes de combustion en mélange pauvre. Les polluants non réglementés pris en considération sont les aldéhydes, les sulfates, l'anhydride sulfureux, l'hydrogène sulfuré, l'oxysulfure de carbone, le cyanogène, l'acide cyanhydrique, l'acide nitrique, les aromatiques légers, les hydrocarbures aromatiques polycycliques, ces derniers en liaison avec leurs propriétés mutagènes. Le catalyseur a été considéré dans différents états : neuf, vieilli, empoisonné : l'influence des déréglages des systèmes de contrôle (avance, sonde à oxygène, allumage, etc. a été prise en compte. Il apparaît que la présence de catalyseur fonctionnant dans des conditions normales se révèle en général bénéfique sur la majorité des polluants ou tout au moins indifférente sur certains polluants. En outre les déréglages éventuels n'entraîneraient pas de concentrations alarmantes de ces polluants non réglementés. Will the equipping of vehicles with catalytic mufflers, planned mainly to reduce the level of currently regulated pollutants (carbon monoxide, unburned hydrocarbons , nitrogen oxides, have a beneficial or harmful effect on unregulated pollutants? To elucidate this question this article considers the vehicles that are the most comparable possible from the standpoint of design and equipment to compare emissions

Approximate Forward Difference Equations for the Lower Order Non-Stationary Statistics of Geometrically Non-Linear Systems subject to Random Excitation

DEFF Research Database (Denmark)

Köylüoglu, H. U.; Nielsen, Søren R. K.; Cakmak, A. S.

Geometrically non-linear multi-degree-of-freedom (MDOF) systems subject to random excitation are considered. New semi-analytical approximate forward difference equations for the lower order non-stationary statistical moments of the response are derived from the stochastic differential equations...... of motion, and, the accuracy of these equations is numerically investigated. For stationary excitations, the proposed method computes the stationary statistical moments of the response from the solution of non-linear algebraic equations....

Non-contact measurement of partial gas pressure and distribution of elemental composition using energy-resolved neutron imaging

Directory of Open Access Journals (Sweden)

A. S. Tremsin

2017-01-01

Full Text Available Neutron resonance absorption imaging is a non-destructive technique that can characterize the elemental composition of a sample by measuring nuclear resonances in the spectrum of a transmitted beam. Recent developments in pixelated time-of-flight imaging detectors coupled with pulsed neutron sources pose new opportunities for energy-resolved imaging. In this paper we demonstrate non-contact measurements of the partial pressure of xenon and krypton gases encapsulated in a steel pipe while simultaneously passing the neutron beam through high-Z materials. The configuration was chosen as a proof of principle demonstration of the potential to make non-destructive measurement of gas composition in nuclear fuel rods. The pressure measured from neutron transmission spectra (∼739 ± 98 kPa and ∼751 ± 154 kPa for two Xe resonances is in relatively good agreement with the pressure value of ∼758 ± 21 kPa measured by a pressure gauge. This type of imaging has been performed previously for solids with a spatial resolution of ∼ 100 μm. In the present study it is demonstrated that the high penetration capability of epithermal neutrons enables quantitative mapping of gases encapsulate within high-Z materials such as steel, tungsten, urania and others. This technique may be beneficial for the non-destructive testing of bulk composition of objects (such as spent nuclear fuel assemblies and others containing various elements opaque to other more conventional imaging techniques. The ability to image the gaseous substances concealed within solid materials also allows non-destructive leak testing of various containers and ultimately measurement of gas partial pressures with sub-mm spatial resolution.

Catalytic antibodies in clinical and experimental pathology: human and mouse models.

Science.gov (United States)

Ponomarenko, Natalya A; Durova, Oxana M; Vorobiev, Ivan I; Aleksandrova, Elena S; Telegin, Georgy B; Chamborant, Olga G; Sidorik, Lyudmila L; Suchkov, Sergei V; Alekberova, Zemfira S; Gnuchev, Nikolay V; Gabibov, Alexander G

2002-11-01

Most of the data accumulated through studies on natural catalytic autoantibodies indicate that production scales up markedly in pathological abnormalities. We have previously described an increased level of DNA-hydrolyzing autoantibodies in the sera of patients with various autoimmune disorders [systemic lupus erythematosus (SLE), rheumatoid arthritis, scleroderma], HIV infection and lymphoproliferative diseases accompanied by autoimmune manifestations. In the present study, we show that an increased level of catalytic activity of autoantibodies can be observed in the sera of autoimmune mice, thus providing a fundamental insight into the medical relevance of abzymes. Polyclonal autoantibodies purified from sera of NZB/W, MRL-lpr/lpr and SJL/J mice show proteolytic and DNA-hydrolyzing activities, as opposed to those harvested from non-autoimmune BALB/c mice. The expressiveness of the catalytic activity was strongly dependent on the age of the animal. The highest levels of catalytic activity were found in the sera of mice aged between 8 and 12 months; the lowest level was typical of younger animals whose age ranged from 6 to 8 weeks. Specific inhibition assays of the catalytic activities were performed to throw light on the nature of the abzyme activity. Within a cohort of aging animals, a strong correlation between marked autoimmune abnormalities and levels of catalytic activities has been established. Nonimmunized SJL/J mice revealed specific immune responses to myelin basic protein (MBP), skeletal muscle myosin (skMyo) and cardiac myosin (Myo), and highly purified antibodies from their serum show specific proteolytic attack against the target antigens. This finding prompted us to undertake a more detailed study of specific antibody-mediated proteolysis in diseased humans. A targeted catalytic response was originally demonstrated against MBP and Myo in multiple sclerosis and myocarditis patients, respectively.

Catalytic distillation structure

Science.gov (United States)

Smith, L.A. Jr.

1984-04-17

Catalytic distillation structure is described for use in reaction distillation columns, and provides reaction sites and distillation structure consisting of a catalyst component and a resilient component intimately associated therewith. The resilient component has at least about 70 volume % open space and is present with the catalyst component in an amount such that the catalytic distillation structure consists of at least 10 volume % open space. 10 figs.

The tritium labeling of Butibufen by heterogeneous catalytic exchange

International Nuclear Information System (INIS)

Santamaria, J.; Rebollo, D.

1986-01-01

The labeling of a new non-steroidal antiinflammatory agent, Butibufen (2-(4-isobutylphenyl) butyric acid) was studied. The method used was heterogeneous catalytic exchange between Butibufen and tritiated water, obtained in situ. Purification was accomplished through thin layer chromatography. Concentration, purity and specific activity of the labeled drug were determined by ultraviolet and liquid scintillation techniques. (Author) 7 refs

Chimeric cellulase matrix for investigating intramolecular synergism between non-hydrolytic disruptive functions of carbohydrate-binding modules and catalytic hydrolysis.

Science.gov (United States)

Wang, Yuguo; Tang, Rentao; Tao, Jin; Wang, Xiaonan; Zheng, Baisong; Feng, Yan

2012-08-24

The conversion of renewable cellulosic biomass is of considerable interest for the production of biofuels and materials. The bottleneck in the efficient conversion is the compactness and resistance of crystalline cellulose. Carbohydrate-binding modules (CBMs), which disrupt crystalline cellulose via non-hydrolytic mechanisms, are expected to overcome this bottleneck. However, the lack of convenient methods for quantitative analysis of the disruptive functions of CBMs have hindered systematic studies and molecular modifications. Here we established a practical and systematic platform for quantifying and comparing the non-hydrolytic disruptive activities of CBMs via the synergism of CBMs and a catalytic module within designed chimeric cellulase molecules. Bioinformatics and computational biology were also used to provide a deeper understanding. A convenient vector was constructed to serve as a cellulase matrix into which heterologous CBM sequences can be easily inserted. The resulting chimeric cellulases were suitable for studying disruptive functions, and their activities quantitatively reflected the disruptive functions of CBMs on crystalline cellulose. In addition, this cellulase matrix can be used to construct novel chimeric cellulases with high hydrolytic activities toward crystalline cellulose.

Chimeric Cellulase Matrix for Investigating Intramolecular Synergism between Non-hydrolytic Disruptive Functions of Carbohydrate-binding Modules and Catalytic Hydrolysis*

Science.gov (United States)

Wang, Yuguo; Tang, Rentao; Tao, Jin; Wang, Xiaonan; Zheng, Baisong; Feng, Yan

2012-01-01

The conversion of renewable cellulosic biomass is of considerable interest for the production of biofuels and materials. The bottleneck in the efficient conversion is the compactness and resistance of crystalline cellulose. Carbohydrate-binding modules (CBMs), which disrupt crystalline cellulose via non-hydrolytic mechanisms, are expected to overcome this bottleneck. However, the lack of convenient methods for quantitative analysis of the disruptive functions of CBMs have hindered systematic studies and molecular modifications. Here we established a practical and systematic platform for quantifying and comparing the non-hydrolytic disruptive activities of CBMs via the synergism of CBMs and a catalytic module within designed chimeric cellulase molecules. Bioinformatics and computational biology were also used to provide a deeper understanding. A convenient vector was constructed to serve as a cellulase matrix into which heterologous CBM sequences can be easily inserted. The resulting chimeric cellulases were suitable for studying disruptive functions, and their activities quantitatively reflected the disruptive functions of CBMs on crystalline cellulose. In addition, this cellulase matrix can be used to construct novel chimeric cellulases with high hydrolytic activities toward crystalline cellulose. PMID:22778256

Catalytic Filtration: A proven technology for Dioxin emission control from waste incinerators

International Nuclear Information System (INIS)

Wong, K.T.; Xu, Zhengtian

2010-01-01

Polychlorinated dibenzo-p-dioxins and di benzofurans (PCD/ Fs), in a family of dioxin derivatives with high toxicity, often associated with environmental pollution are the most toxic man made substances, emitted in gas and solid phases during incineration of waste. The threat of dioxin is drawing increasing attention around the world. Governments around the world are phasing in more stringent dioxin emission regulations, and reports about dioxin levels in food products have generated widespread concerns among the public. Issues related to dioxin emissions and disposals are moving up the environmental agenda demanding the most effective and environmentally sound technologies. With heightened public awareness, more stringent regulations, and potential penalties for non-compliance, its more important than ever to avoid the risks associated with inadequate dioxin control. The permissible dioxin emission in most industrial nations is less than 0.1 ng (TEQ)/ Nm 3 and permissible dust emission is from less than 10 to less than 50 mg/ Nm 3 . The common system to remove dioxin is installing an injection process for powdered activated carbon (PAC). This was seen as a proven and widely used technology to control dioxin. This sorbent based system moves dioxin and furan molecules from the gas stream to the solid residue. There are new concerns about existing or future landfill restrictions on the amount and toxicity of sorbent levels in fly ash. Other alternatives are non-flammable additives and catalytic technologies. The non-flammable additives are not proven to control dioxin at temperatures above 200 degree Celsius. Catalytic filter technology can be high initial investment but gaining popularity for operational benefits and reduction of solid residues for landfill. Several criteria are being considered to compare the initial cost of the catalytic filter system and the cost reduction of exhaust gas treatment that can pay for the return of the investment. Field experiences

Catalytic site identification—a web server to identify catalytic site structural matches throughout PDB

Science.gov (United States)

Kirshner, Daniel A.; Nilmeier, Jerome P.; Lightstone, Felice C.

2013-01-01

The catalytic site identification web server provides the innovative capability to find structural matches to a user-specified catalytic site among all Protein Data Bank proteins rapidly (in less than a minute). The server also can examine a user-specified protein structure or model to identify structural matches to a library of catalytic sites. Finally, the server provides a database of pre-calculated matches between all Protein Data Bank proteins and the library of catalytic sites. The database has been used to derive a set of hypothesized novel enzymatic function annotations. In all cases, matches and putative binding sites (protein structure and surfaces) can be visualized interactively online. The website can be accessed at http://catsid.llnl.gov. PMID:23680785

Synthesis, characterization and catalytic properties of nanocrystaline Y2O3-coated TiO2 in the ethanol dehydration reaction

Directory of Open Access Journals (Sweden)

Humberto Vieira Fajardo

2012-04-01

Full Text Available In the present study, TiO2 nanopowder was partially coated with Y2O3 precursors generated by a sol-gel modified route. The system of nanocoated particles formed an ultra thin structure on the TiO2 surfaces. The modified nanoparticles were characterized by high resolution transmission electron microscopy (HR-TEM, X-ray diffraction (XRD analysis, Zeta potential and surface area through N2 fisisorption measurements. Bioethanol dehydration was used as a probe reaction to investigate the modifications on the nanoparticles surface. The process led to the obtainment of nanoparticles with important surface characteristics and catalytic behavior in the bioethanol dehydration reaction, with improved activity and particular selectivity in comparison to their non-coated analogs. The ethylene production was disfavored and selectivity toward acetaldehyde, hydrogen and ethane increased over modified nanoparticles.

Fuel Flexible, Low Emission Catalytic Combustor for Opportunity Fuel Applications

Energy Technology Data Exchange (ETDEWEB)

Eteman, Shahrokh

2013-06-30

Limited fuel resources, increasing energy demand and stringent emission regulations are drivers to evaluate process off-gases or process waste streams as fuels for power generation. Often these process waste streams have low energy content and/or highly reactive components. Operability of low energy content fuels in gas turbines leads to issues such as unstable and incomplete combustion. On the other hand, fuels containing higher-order hydrocarbons lead to flashback and auto-ignition issues. Due to above reasons, these fuels cannot be used directly without modifications or efficiency penalties in gas turbine engines. To enable the use of these wide variety of fuels in gas turbine engines a rich catalytic lean burn (RCL®) combustion system was developed and tested in a subscale high pressure (10 atm.) rig. The RCL® injector provided stability and extended turndown to low Btu fuels due to catalytic pre-reaction. Previous work has shown promise with fuels such as blast furnace gas (BFG) with LHV of 85 Btu/ft3 successfully combusted. This program extends on this work by further modifying the combustor to achieve greater catalytic stability enhancement. Fuels containing low energy content such as weak natural gas with a Lower Heating Value (LHV) of 6.5 MJ/m3 (180 Btu/ft3 to natural gas fuels containing higher hydrocarbon (e.g ethane) with LHV of 37.6 MJ/m3 (1010 Btu/ft3) were demonstrated with improved combustion stability; an extended turndown (defined as the difference between catalytic and non-catalytic lean blow out) of greater than 250oF was achieved with CO and NOx emissions lower than 5 ppm corrected to 15% O2. In addition, for highly reactive fuels the catalytic region preferentially pre-reacted the higher order hydrocarbons with no events of flashback or auto-ignition allowing a stable and safe operation with low NOx and CO emissions.

A non-acid-assisted and non-hydroxyl-radical-related catalytic ozonation with ceria supported copper oxide in efficient oxalate degradation in water

KAUST Repository

Zhang, Tao

2012-06-01

Oxalate is usually used as a refractory model compound that cannot be effectively removed by ozone and hydroxyl radical oxidation in water. In this study, we found that ceria supported CuO significantly improved oxalate degradation in reaction with ozone. The optimum CuO loading amount was 12%. The molar ratio of oxalate removed/ozone consumption reached 0.84. The catalytic ozonation was most effective in a neutral pH range (6.7-7.9) and became ineffective when the water solution was acidic or alkaline. Moreover, bicarbonate, a ubiquitous hydroxyl radical scavenger in natural waters, significantly improved the catalytic degradation of oxalate. Therefore, the degradation relies on neither hydroxyl radical oxidation nor acid assistance, two pathways usually proposed for catalytic ozonation. These special characters of the catalyst make it suitable to be potentially used for practical degradation of refractory hydrophilic organic matter and compounds in water and wastewater. With in situ characterization, the new surface Cu(II) formed from ozone oxidation of the trace Cu(I) of the catalyst was found to be an active site in coordination with oxalate forming multi-dentate surface complex. It is proposed that the complex can be further oxidized by molecular ozone and then decomposes through intra-molecular electron transfer. The ceria support enhanced the activity of the surface Cu(I)/Cu(II) in this process. © 2012 Elsevier B.V.

Investigating oral health-related quality of life and self-perceived satisfaction with partial dentures.

Science.gov (United States)

Abuzar, Menaka A; Kahwagi, Esperance; Yamakawa, Takeshi

2012-05-01

To investigate the prevalence and severity of oral health-related quality of life in patients treated with removable partial dentures at a publicly-funded dental hospital. The association between patients' demographic profiles, denture-related, variables and oral health-related quality of life was also investigated. A questionnaire was designed to investigate the use and satisfaction of removable partial dentures, and oral health-related quality of life of removable partial denture wearers using the Oral Health Impact Profile-14. The questionnaire was administered to 740 randomly-selected patients who received removable partial dentures during 2005-2008. The response rate was 31.35%. Non-parametric tests and a logistic regression model were used to analyze the association between denture-related variables and oral health-related quality of life. A question on symptoms unrelated to dentures was also analyzed. The Oral Health Impact Profile-14 prevalence calculated was 43.1%. The removable partial denture experience and frequency of use was inversely associated with Oral Health Impact Profile-14 scores. Metal-based removable partial dentures were associated with lower Oral Health Impact Profile prevalence and severity scores. No significant association was found between demographic profile, circumstance for provision of removable partial dentures and Oral Health Impact Profile-14 score. The participants of this study indicated that perceived denture performance, removable partial dentures material, experience, and frequency of use are associated with oral health-related quality of life. © 2012 Blackwell Publishing Asia Pty Ltd.

Equivalent non-Gaussian excitation method for response moment calculation of systems under non-Gaussian random excitation

International Nuclear Information System (INIS)

Tsuchida, Takahiro; Kimura, Koji

2015-01-01

Equivalent non-Gaussian excitation method is proposed to obtain the moments up to the fourth order of the response of systems under non-Gaussian random excitation. The excitation is prescribed by the probability density and power spectrum. Moment equations for the response can be derived from the stochastic differential equations for the excitation and the system. However, the moment equations are not closed due to the nonlinearity of the diffusion coefficient in the equation for the excitation. In the proposed method, the diffusion coefficient is replaced with the equivalent diffusion coefficient approximately to obtain a closed set of the moment equations. The square of the equivalent diffusion coefficient is expressed by the second-order polynomial. In order to demonstrate the validity of the method, a linear system to non-Gaussian excitation with generalized Gaussian distribution is analyzed. The results show the method is applicable to non-Gaussian excitation with the widely different kurtosis and bandwidth. (author)

High aspect ratio catalytic reactor and catalyst inserts therefor

Science.gov (United States)

Lin, Jiefeng; Kelly, Sean M.

2018-04-10

The present invention relates to high efficient tubular catalytic steam reforming reactor configured from about 0.2 inch to about 2 inch inside diameter high temperature metal alloy tube or pipe and loaded with a plurality of rolled catalyst inserts comprising metallic monoliths. The catalyst insert substrate is formed from a single metal foil without a central supporting structure in the form of a spiral monolith. The single metal foil is treated to have 3-dimensional surface features that provide mechanical support and establish open gas channels between each of the rolled layers. This unique geometry accelerates gas mixing and heat transfer and provides a high catalytic active surface area. The small diameter, high aspect ratio tubular catalytic steam reforming reactors loaded with rolled catalyst inserts can be arranged in a multi-pass non-vertical parallel configuration thermally coupled with a heat source to carry out steam reforming of hydrocarbon-containing feeds. The rolled catalyst inserts are self-supported on the reactor wall and enable efficient heat transfer from the reactor wall to the reactor interior, and lower pressure drop than known particulate catalysts. The heat source can be oxygen transport membrane reactors.

Optical manipulation and catalytic activity enhanced by surface plasmon effect

Science.gov (United States)

Zou, Ningmu; Min, Jiang; Jiao, Wenxiang; Wang, Guanghui

2017-02-01

For optical manipulation, a nano-optical conveyor belt consisting of an array of gold plasmonic non-concentric nano-rings (PNNRs) is demonstrated for the realization of trapping and unidirectional transportation of nanoparticles by polarization rotation of excitation beam. These hot spots of an asymmetric plasmonic nanostructure are polarization dependent, therefore, one can use the incident polarization state to manipulate the trapped targets. Trapped particles could be transferred between adjacent PNNRs in a given direction just by rotating the polarization of incident beam due to unbalanced potential. The angular dependent distribution of electric field around PNNR has been solved using the three- dimensional finite-difference time-domain (FDTD) technique. For optical enhanced catalytic activity, the spectral properties of dimers of Au nanorod-Au nanorod nanostructures under the excitation of 532nm photons have been investigated. With a super-resolution catalytic mapping technique, we identified the existence of "hot spot" in terms of catalytic reactivity at the gap region within the twined plasmonic nanostructure. Also, FDTD calculation has revealed an intrinsic correlation between hot electron transfer.

Kinetic Study of the Catalytic Pyrolysis of Oil-Containing Waste

Directory of Open Access Journals (Sweden)

Kirill Chalov

2016-10-01

Full Text Available Basing on the experimental data the optimal parameters of the pyrolysis of heavy and residual hydrocarbons of oil were defined as follows: temperature of 500 °С; catalyst  of CoCl2 with the catalyst loading 5% (wt. of the substrate weight. Under the optimal conditions the kinetic investigation of the pyrolysis process was carried out using the thermogravimetric method. According to the investigation, it was found that the activation energy of the catalytic pyrolysis of oil-containing waste decreased by 20-30 kJ/mol in comparison to non-catalytic process. Copyright © 2016 BCREC GROUP. All rights reserved Received: 13th July 2015; Revised: 25th March 2016; Accepted: 1st April 2016 How to Cite: Chalov, K., Lugovoy, Y., Kosivtsov, Y., Sulman, M., Sulman, E., Matveeva, V., Stepacheva, A. (2016. Kinetic Study of the Catalytic Pyrolysis of Oil-Containing Waste. Bulletin of Chemical Reaction Engineering & Catalysis, 11 (3: 330-338 (doi:10.9767/bcrec.11.3.572.330-338 Permalink/DOI: http://doi.org/10.9767/bcrec.11.3.572.330-338

TET2 Regulates Mast Cell Differentiation and Proliferation through Catalytic and Non-catalytic Activities

Directory of Open Access Journals (Sweden)

Sara Montagner

2016-05-01

Full Text Available Summary: Dioxygenases of the TET family impact genome functions by converting 5-methylcytosine (5mC in DNA to 5-hydroxymethylcytosine (5hmC. Here, we identified TET2 as a crucial regulator of mast cell differentiation and proliferation. In the absence of TET2, mast cells showed disrupted gene expression and altered genome-wide 5hmC deposition, especially at enhancers and in the proximity of downregulated genes. Impaired differentiation of Tet2-ablated cells could be relieved or further exacerbated by modulating the activity of other TET family members, and mechanistically it could be linked to the dysregulated expression of C/EBP family transcription factors. Conversely, the marked increase in proliferation induced by the loss of TET2 could be rescued exclusively by re-expression of wild-type or catalytically inactive TET2. Our data indicate that, in the absence of TET2, mast cell differentiation is under the control of compensatory mechanisms mediated by other TET family members, while proliferation is strictly dependent on TET2 expression. : The impact of TET enzymes on gene expression and cell function is incompletely understood. Montagner et al. investigate the TET-mediated regulation of mast cell differentiation and function, uncover transcriptional pathways regulated by TET2, and identify both enzymatic activity-dependent and -independent functions of TET2. Keywords: differentiation, DNA hydroxymethylation, epigenetics, mast cells, proliferation, TET

Method of fabricating a catalytic structure

Science.gov (United States)

Rollins, Harry W [Idaho Falls, ID; Petkovic, Lucia M [Idaho Falls, ID; Ginosar, Daniel M [Idaho Falls, ID

2009-09-22

A precursor to a catalytic structure comprising zinc oxide and copper oxide. The zinc oxide has a sheet-like morphology or a spherical morphology and the copper oxide comprises particles of copper oxide. The copper oxide is reduced to copper, producing the catalytic structure. The catalytic structure is fabricated by a hydrothermal process. A reaction mixture comprising a zinc salt, a copper salt, a hydroxyl ion source, and a structure-directing agent is formed. The reaction mixture is heated under confined volume conditions to produce the precursor. The copper oxide in the precursor is reduced to copper. A method of hydrogenating a carbon oxide using the catalytic structure is also disclosed, as is a system that includes the catalytic structure.

Modelling of a reverse flow catalytic membrane reactor for the partial oxidation of methane

NARCIS (Netherlands)

Smit, J.; van Sint Annaland, M.; Kuipers, J.A.M.

2003-01-01

Gas-To-Liquid (GTL) processes have great potential as alternative to conventional oil and coal processing for the production of liquid fuels. In GTL-processes the partial oxidation of methane (POM) is combined with the Fischer-Tropsch reaction. An important part of the investment costs of a

Non-uniform approximations for sums of discrete m-dependent random variables

OpenAIRE

Vellaisamy, P.; Cekanavicius, V.

2013-01-01

Non-uniform estimates are obtained for Poisson, compound Poisson, translated Poisson, negative binomial and binomial approximations to sums of of m-dependent integer-valued random variables. Estimates for Wasserstein metric also follow easily from our results. The results are then exemplified by the approximation of Poisson binomial distribution, 2-runs and $m$-dependent $(k_1,k_2)$-events.

Algebraic partial Boolean algebras

International Nuclear Information System (INIS)

Smith, Derek

2003-01-01

Partial Boolean algebras, first studied by Kochen and Specker in the 1960s, provide the structure for Bell-Kochen-Specker theorems which deny the existence of non-contextual hidden variable theories. In this paper, we study partial Boolean algebras which are 'algebraic' in the sense that their elements have coordinates in an algebraic number field. Several of these algebras have been discussed recently in a debate on the validity of Bell-Kochen-Specker theorems in the context of finite precision measurements. The main result of this paper is that every algebraic finitely-generated partial Boolean algebra B(T) is finite when the underlying space H is three-dimensional, answering a question of Kochen and showing that Conway and Kochen's infinite algebraic partial Boolean algebra has minimum dimension. This result contrasts the existence of an infinite (non-algebraic) B(T) generated by eight elements in an abstract orthomodular lattice of height 3. We then initiate a study of higher-dimensional algebraic partial Boolean algebras. First, we describe a restriction on the determinants of the elements of B(T) that are generated by a given set T. We then show that when the generating set T consists of the rays spanning the minimal vectors in a real irreducible root lattice, B(T) is infinite just if that root lattice has an A 5 sublattice. Finally, we characterize the rays of B(T) when T consists of the rays spanning the minimal vectors of the root lattice E 8

Effect of support on the catalytic activity of manganese oxide catalyts for toluene combustion

International Nuclear Information System (INIS)

Pozan, Gulin Selda

2012-01-01

Highlights: ► α-Al 2 O 3 , obtained from Bohmite, as a support for enhancing of the activity. ► The support material for catalytic oxidation. ► The manganese state and oxygen species effect on the catalytic combustion reaction. - Abstract: The aim of this work was to study combustion of toluene (1000 ppm) over MnO 2 modified with different supports. α-Al 2 O 3 and γ-Al 2 O 3 obtained from Boehmite, γ-Al 2 O 3 (commercial), SiO 2 , TiO 2 and ZrO 2 were used as commercial support materials. In view of potential interest of this process, the influence of support material on the catalytic performance was discussed. The deposition of 9.5MnO 2 was performed by impregnation over support. The catalysts were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), temperature programmed reduction and oxidation (TPR/TPO) and thermogravimetric analysis (TGA). The catalytic tests were carried out at atmospheric pressure in a fixed-bed flow reactor. 9.5MnO 2 /α-Al 2 O 3 (B) (synthesized from Boehmite) catalyst exhibits the highest catalytic activity, over which the toluene conversion was up to 90% at a temperature of 289 °C. Considering all the characterization and reaction data reported in this study, it was concluded that the manganese state and oxygen species played an important role in the catalytic activity.

Microwave catalytic NOx and SO{sub 2} removal using FeCu/zeolite as catalyst

Energy Technology Data Exchange (ETDEWEB)

Z.S. Wei; G.H. Zeng; Z.R. Xie; C.Y. Ma; X.H. Liu; J.L. Sun; L.H. Liu [Sun Yat-sen University, Guangzhou (China). School of Environmental Science and Engineering

2011-04-15

Non-thermal plasma technology is a promising process for flue gas treatment. Microwave catalytic NOx and SO{sub 2} removal simultaneously has been investigated using FeCu/zeolite as catalyst. The experimental results showed that a microwave reactor with FeCu/zeolite only could be used to microwave catalytic oxidative 91.7% NOx to nitrates and 79.6% SO{sub 2} to sulfate; the reaction efficiencies of microwave catalytic reduction of NOx and SO{sub 2} in a microwave reactor with FeCu/zeolite and ammonium bicarbonate (NH{sub 4}HCO{sub 3}) as a reducing agent could be up to 95.8% and 93.4% respectively. Microwave irradiation accentuates catalytic reduction of SO{sub 2} and NOx treatment, and microwave addition can increases SO{sub 2} removal efficiency from 14.5% to 18.7%, and NOx removal efficiency from 13.4% to 18.7%, separately. FeCu/zeolite catalyst was characterized by X-ray diffraction (XRD), X-ray photoelectron spectrum analysis (XPS), scanning electron microscopy (SEM) and the Brunauer Emmett Teller (BET) method. Microwave catalytic NOx and SO{sub 2} removal follows Langmuir-Hinshelwood (L-H) kinetics. 25 refs., 7 figs., 1 tab.

The Kinetics of Chirality Assignment in Catalytic Single Walled Carbon Nanotube Growth

OpenAIRE

Xu, Ziwei; Yan, Tianying; Ding, Feng

2014-01-01

Chirality-selected single-walled carbon nanotubes (SWCNTs) ensure a great potential of building ~1 nm sized electronics. However, the reliable method for chirality-selected SWCNT is still pending. Here we present a theoretical study on the SWCNT's chirality assignment and control during the catalytic growth. This study reveals that the chirality of a SWCNT is determined by the kinetic incorporation of the pentagon formation during SWCNT nucleation. Therefore, chirality is randomly assigned on...

Perturbation Solutions for Random Linear Structural Systems subject to Random Excitation using Stochastic Differential Equations

DEFF Research Database (Denmark)

Köyluoglu, H.U.; Nielsen, Søren R.K.; Cakmak, A.S.

1994-01-01

perturbation method using stochastic differential equations. The joint statistical moments entering the perturbation solution are determined by considering an augmented dynamic system with state variables made up of the displacement and velocity vector and their first and second derivatives with respect......The paper deals with the first and second order statistical moments of the response of linear systems with random parameters subject to random excitation modelled as white-noise multiplied by an envelope function with random parameters. The method of analysis is basically a second order...... to the random parameters of the problem. Equations for partial derivatives are obtained from the partial differentiation of the equations of motion. The zero time-lag joint statistical moment equations for the augmented state vector are derived from the Itô differential formula. General formulation is given...

Partial Pulpotomy in Mature Permanent Teeth with Clinical Signs Indicative of Irreversible Pulpitis: A Randomized Clinical Trial.

Science.gov (United States)

Taha, Nessrin A; Khazali, Mohammad A

2017-09-01

This study aimed to assess the outcome of partial pulpotomy using mineral trioxide aggregate (MTA) compared with calcium hydroxide (CH) in mature cariously exposed permanent molars. Fifty permanent molar teeth with carious exposures in 50 patients >20 years old were included. Preoperative pulpal and periapical diagnosis was established based on a history of presenting pain, results of cold testing, and radiographic findings. After informed consent, the tooth was anesthetized, isolated via a dental dam, and disinfected with 5% sodium hypochlorite before caries excavation. Partial pulpotomy was performed by amputating 2 mm of the exposed pulp, hemostasis was achieved, and the tooth was randomly assigned for the placement of either white MTA (White ProRoot; Dentsply, Tulsa, OK) or CH (Dycal; Dentsply Caulk, Milford, DE) as the pulpotomy agent. Postoperative periapical radiographs were taken after placement of the permanent restoration. Clinical and radiographic evaluation was completed after 6 months and 1 and 2 years postoperatively. Statistical analysis was performed using the Fisher exact test. Clinical signs and symptoms suggestive of irreversible pulpitis were established in all teeth. Immediate failure occurred in 4 teeth. At 1 year, MTA showed a higher tendency toward success compared with the CH group, and the difference was statistically significant after 2 years (83% vs 55%, P = .052 at 1 year; 85% vs 43%, P = .006 at 2 years). Sex did not have a statistically significant effect on the outcome. MTA partial pulpotomy sustained a good success rate over the 2-year follow-up in mature permanent teeth clinically diagnosed with irreversible pulpitis. More than half of the CH cases failed within 2 years. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Intracrystalline fractionation of oxygen isotopes between hydroxyl and non-hydroxyl sites in kaolinite measured by thermal dehydroxylation and partial fluorination

Science.gov (United States)

Girard, Jean-Pierre; Savin, Samuel M.

1996-02-01

Thermal dehydroxylation and partial fluorination techniques were used to measure intracrystalline fractionation of oxygen isotopes between hydroxyl and non-hydroxyl sites in kaolinite. Several aliquots of a well characterized, fine-grained (rates, and target temperatures. Measured δ18O values of both the liberated water and the dehydroxylated residue are consistent over a wide range of temperatures (550 850°C) when dehydroxylation is performed in a single-step fashion at a rapid heating rate (>50°C/min.). Similar dehydroxylation experiments indicate that brucite dehydroxylation occurs without any significant isotopic fractionation of the oxygen isotopes. By extrapolation we postulate that no significant fractionation occurs during single-step thermal dehydroxylation of fine-grained kaolinite, provided that dehydroxylation is performed under well controlled conditions. In contrast, gibbsite dehydroxylation is accompanied by substantial isotopic fractionation. This is probably the result of the complex, multi-pathway dehydroxylation reaction of this mineral. Similarly, thermal dehydroxylation of coarsegrained (>1 μm) kaolinites and dickites of weathering and hydrothermal origin yield results that are dependent on the temperature of dehydroxylation. We suggest that this effect may be caused by isotopic exchange during diffusion of water molecules through coarse particles. Partial fluorination of fine-grained kaolinite in the presence of excess F2 at low temperatures (rate of reaction of hydroxyl oxygen than of non-hydroxyl oxygen, but examination of the isotopic data as well as XRD and IR analyses of the residues after partial fluorination indicates that the separation between the two types of oxygen is not complete. The results, therefore, do not yield a reliable δ18O value of the hydroxyl oxygen. The results of this study suggest that the thermal dehydroxylation technique may be appropriate for analysis of OH groups in fine-grained kaolinite. The partial

Online games: a novel approach to explore how partial information influences human random searches

Science.gov (United States)

Martínez-García, Ricardo; Calabrese, Justin M.; López, Cristóbal

2017-01-01

Many natural processes rely on optimizing the success ratio of a search process. We use an experimental setup consisting of a simple online game in which players have to find a target hidden on a board, to investigate how the rounds are influenced by the detection of cues. We focus on the search duration and the statistics of the trajectories traced on the board. The experimental data are explained by a family of random-walk-based models and probabilistic analytical approximations. If no initial information is given to the players, the search is optimized for cues that cover an intermediate spatial scale. In addition, initial information about the extension of the cues results, in general, in faster searches. Finally, strategies used by informed players turn into non-stationary processes in which the length of e ach displacement evolves to show a well-defined characteristic scale that is not found in non-informed searches.

Human acid β-glucosidase: isolation and amino acid sequence of a peptide containing the catalytic site

International Nuclear Information System (INIS)

Dinur, T.; Osiecki, K.M.; Legler, G.; Gatt, S.; Desnick, R.J.; Grabowski, G.A.

1986-01-01

Human acid β-glucosidase (D-glucosyl-N-acylsphingosine glucohydrolase, EC 3.2.1.45) cleaves the glucosidic bonds of glucosylceramide and synthetic β-glucosides. The deficient activity of this hydrolase is the enzymatic defect in the subtypes and variants of Gaucher disease, the most prevalent lysosomal storage disease. To isolate and characterize the catalytic site of the normal enzyme, brominated 3 H-labeled conduritol B epoxide ( 3 H-Br-CBE), which inhibits the enzyme by binding covalently to this site, was used as an affinity label. Under optimal conditions 1 mol of 3 H-Br-CBE bound to 1 mol of pure enzyme protein, indicating the presence of a single catalytic site per enzyme subunit. After V 8 protease digestion of the 3 H-Br-CBE-labeled homogeneous enzyme, three radiolabeled peptides, designated peptide A, B, or C, were resolved by reverse-phase HPLC. The partial amino acid sequence (37 residues) of peptide A (M/sub r/, 5000) was determined. The sequence of this peptide, which contained the catalytic site, had exact homology to the sequence near the carboxyl terminus of the protein, as predicted from the nucleotide sequence of the full-length cDNA encoding acid β-glucosidase

Randomized phase II study of vandetanib alone or with paclitaxel and carboplatin as first-line treatment for advanced non-small-cell lung cancer.

Science.gov (United States)

Heymach, John V; Paz-Ares, Luis; De Braud, Filippo; Sebastian, Martin; Stewart, David J; Eberhardt, Wilfried E E; Ranade, Anantbhushan A; Cohen, Graham; Trigo, Jose Manuel; Sandler, Alan B; Bonomi, Philip D; Herbst, Roy S; Krebs, Annetta D; Vasselli, James; Johnson, Bruce E

2008-11-20

Vandetanib is a once-daily, oral inhibitor of vascular endothelial growth factor receptor and epidermal growth factor receptor signaling. The antitumor activity of vandetanib monotherapy or vandetanib with paclitaxel and carboplatin (VPC) was compared with paclitaxel and carboplatin (PC) in previously untreated patients with non-small-cell lung cancer (NSCLC). All NSCLC histologies and previously treated CNS metastases were permitted in this partially blinded, placebo-controlled, randomized phase II study. Patients were randomly assigned 2:1:1 to receive vandetanib, VPC, or PC. Progression-free survival (PFS) was the primary end point, and the study was powered to detect a reduced risk of progression with VPC versus PC (hazard ratio = 0.70; one-sided P 1.33 v PC). Overall survival was not significantly different between patients receiving VPC or PC. Rash, diarrhea, and hypertension were common adverse events; no pulmonary or CNS hemorrhage events required intervention. VPC could be safely administered to patients with NSCLC, including those with squamous cell histology and treated brain metastases. Compared with the PC control arm, patients receiving VPC had longer PFS, meeting the prespecified study end point, whereas those receiving vandetanib monotherapy had shorter PFS.

The catalytic activity of several tungsten oxides for the oxidation of propene

International Nuclear Information System (INIS)

De Rossi, S.; Schiavello, M.; Rome Univ.; Iguchi, E.; Tilley, R.J.D.

1976-01-01

A study has been made of the catalytic oxidation of propene over the oxides WO 3 , WOsub(2,95), WOsub(2,90), WOsub(2,72) and Wo 2 , which were selected because they possess specific features of chemical and structural interest rather than for their catalytic ability. It was found that the oxides WOsub(2,95), WOsub(2,90) and WOsub(2,72) all selectively produce acrolein in small amounts. The oxides WO 3 and WO 2 were non-selective and rather inactive. The results are discussed in terms of a mechanism involving both variable valence in the crystal and the specific structural geometry of these compounds. (orig.) [de

Challenges in process integration of catalytic DC plasma synthesis of vertically aligned carbon nanofibres

International Nuclear Information System (INIS)

Melechko, Anatoli V; Pearce, Ryan C; Hensley, Dale K; Simpson, Michael L; McKnight, Timothy E

2011-01-01

The ability to synthesize free-standing, individual carbon nanofibres (CNFs) aligned perpendicularly to a substrate has enabled fabrication of a large array of devices with nanoscale functional elements, including electron field emission sources, electrochemical probes, neural interface arrays, scanning probes, gene delivery arrays and many others. This was made possible by development of a catalytic plasma process, with DC bias directing the alignment of nanofibres. Successful implementation of prototypical devices has uncovered numerous challenges in the integration of this synthesis process as one of the steps in device fabrication. This paper is dedicated to these engineering and fundamental difficulties that hinder further device development. Relatively high temperature for catalytic synthesis, electrical conductivity of the substrate to maintain DC discharge and other difficulties place restrictions on substrate material. Balancing non-catalytic carbon film deposition and substrate etching, non-uniformity of plasma due to growth of the high aspect ratio structures, plasma instabilities and other factors lead to challenges in controlling the plasma. Ultimately, controlling the atomistic processes at the catalyst nanoparticle (NP) and the behaviour of the NP is the central challenge of plasma nanosynthesis of vertically aligned CNFs.

Accelerated Partial Breast Irradiation With IMRT: New Technical Approach and Interim Analysis of Acute Toxicity in a Phase III Randomized Clinical Trial

International Nuclear Information System (INIS)

Livi, Lorenzo; Buonamici, Fabrizio Banci; Simontacchi, Gabriele; Scotti, Vieri; Fambrini, Massimiliano; Compagnucci, Antonella; Paiar, Fabiola; Scoccianti, Silvia; Pallotta, Stefania; Detti, Beatrice; Agresti, Benedetta; Talamonti, Cinzia; Mangoni, Monica; Bianchi, Simonetta; Cataliotti, Luigi; Marrazzo, Livia; Bucciolini, Marta; Biti, Giampaolo

2010-01-01

Purpose: To evaluate with a randomized clinical trial the possibility of treating the index quadrant with external intensity-modulated radiotherapy (IMRT) in a selected group of patients with early-stage breast cancer and to analyze the acute toxicity. Methods and Materials: From September 2005, a randomized Phase III clinical trial has been conducted to compare conventional (tangential field) fractionated whole breast treatment (Arm A) with accelerated partial breast irradiation plus intensity-modulated radiotherapy (Arm B). For intensity-modulated radiotherapy, the clinical target volume was drawn with a uniform 1-cm margin around the surgical clips in three dimensions. The ipsilateral and contralateral breast, ipsilateral and contralateral lung, heart, and spinal cord were contoured as organs at risk. All the regions of interest were contoured according to the International Commission on Radiation Units and Measurements reports 50 and 62 recommendations. Results: In September 2008, 259 patients were randomized and treated. The mean clinical target volume in Arm B was 44 cm 3 and the mean planning target volume was 123 cm 3 . The mean value of the ratio between the planning target volume and the ipsilateral breast volume was 21%. The rate of Grade 1 and Grade 2 acute skin toxicity was 22% and 19% in Arm A (Radiation Therapy Oncology Group scale), respectively. The tolerance in Arm B was excellent with only 5% Grade 1 and 0.8% Grade 2 acute skin toxicity. The planning constraints were fully satisfied in most patients. In a very few cases, this was not possible because of very unfavorable anatomy. Quality assurance procedures were performed according to our internal quality assurance protocol, with excellent results. Conclusion: In the present preliminary analysis, we have demonstrated that accelerated partial breast irradiation is feasible, with very low acute toxicity.

Networks of High Mutual Information Define the Structural Proximity of Catalytic Sites: Implications for Catalytic Residue Identification

DEFF Research Database (Denmark)

Buslje, Cristina Marino; Teppa, Elin; Di Doménico, Tomas

2010-01-01

other non-functional conserved residues. Using a data set of 434 Pfam families included in the catalytic site atlas (CSA) database, we tested this hypothesis and demonstrated that MI can complement amino acid conservation scores to detect CR. The Kullback-Leibler (KL) conservation measurement was shown.......90, the Cls method was found to have a sensitivity of 0.816. In summary, we demonstrate that networks of residues with high MI provide a distinct signature on CR and propose that such a signature should be present in other classes of functional residues where the requirement to maintain a particular function...

Heterogeneous catalytic materials solid state chemistry, surface chemistry and catalytic behaviour

CERN Document Server

Busca, Guido

2014-01-01

Heterogeneous Catalytic Materials discusses experimental methods and the latest developments in three areas of research: heterogeneous catalysis; surface chemistry; and the chemistry of catalysts. Catalytic materials are those solids that allow the chemical reaction to occur efficiently and cost-effectively. This book provides you with all necessary information to synthesize, characterize, and relate the properties of a catalyst to its behavior, enabling you to select the appropriate catalyst for the process and reactor system. Oxides (used both as catalysts and as supports for cata

A three operator split-step method covering a larger set of non-linear partial differential equations

Science.gov (United States)

Zia, Haider

2017-06-01

This paper describes an updated exponential Fourier based split-step method that can be applied to a greater class of partial differential equations than previous methods would allow. These equations arise in physics and engineering, a notable example being the generalized derivative non-linear Schrödinger equation that arises in non-linear optics with self-steepening terms. These differential equations feature terms that were previously inaccessible to model accurately with low computational resources. The new method maintains a 3rd order error even with these additional terms and models the equation in all three spatial dimensions and time. The class of non-linear differential equations that this method applies to is shown. The method is fully derived and implementation of the method in the split-step architecture is shown. This paper lays the mathematical ground work for an upcoming paper employing this method in white-light generation simulations in bulk material.

N-Methylamino Pyrimidyl Amides (MAPA): Highly Reactive, Electronically-Activated Amides in Catalytic N-C(O) Cleavage.

Science.gov (United States)

Meng, Guangrong; Lalancette, Roger; Szostak, Roman; Szostak, Michal

2017-09-01

Despite recent progress in catalytic cross-coupling technologies, the direct activation of N-alkyl-N-aryl amides has been a challenging transformation. Here, we report the first Suzuki cross-coupling of N-methylamino pyrimidyl amides (MAPA) enabled by the controlled n N → π Ar conjugation and the resulting remodeling of the partial double bond character of the amide bond. The new mode of amide activation is suitable for generating acyl-metal intermediates from unactivated primary and secondary amides.

Partial Discharge Monitoring on Metal-Enclosed Switchgear with Distributed Non-Contact Sensors

Directory of Open Access Journals (Sweden)

Chongxing Zhang

2018-02-01

Full Text Available Metal-enclosed switchgear, which are widely used in the distribution of electrical energy, play an important role in power distribution networks. Their safe operation is directly related to the reliability of power system as well as the power quality on the consumer side. Partial discharge detection is an effective way to identify potential faults and can be utilized for insulation diagnosis of metal-enclosed switchgear. The transient earth voltage method, an effective non-intrusive method, has substantial engineering application value for estimating the insulation condition of switchgear. However, the practical application effectiveness of TEV detection is not satisfactory because of the lack of a TEV detection application method, i.e., a method with sufficient technical cognition and analysis. This paper proposes an innovative online PD detection system and a corresponding application strategy based on an intelligent feedback distributed TEV wireless sensor network, consisting of sensing, communication, and diagnosis layers. In the proposed system, the TEV signal or status data are wirelessly transmitted to the terminal following low-energy signal preprocessing and acquisition by TEV sensors. Then, a central server analyzes the correlation of the uploaded data and gives a fault warning level according to the quantity, trend, parallel analysis, and phase resolved partial discharge pattern recognition. In this way, a TEV detection system and strategy with distributed acquisition, unitized fault warning, and centralized diagnosis is realized. The proposed system has positive significance for reducing the fault rate of medium voltage switchgear and improving its operation and maintenance level.

Partial Discharge Monitoring on Metal-Enclosed Switchgear with Distributed Non-Contact Sensors.

Science.gov (United States)

Zhang, Chongxing; Dong, Ming; Ren, Ming; Huang, Wenguang; Zhou, Jierui; Gao, Xuze; Albarracín, Ricardo

2018-02-11

Metal-enclosed switchgear, which are widely used in the distribution of electrical energy, play an important role in power distribution networks. Their safe operation is directly related to the reliability of power system as well as the power quality on the consumer side. Partial discharge detection is an effective way to identify potential faults and can be utilized for insulation diagnosis of metal-enclosed switchgear. The transient earth voltage method, an effective non-intrusive method, has substantial engineering application value for estimating the insulation condition of switchgear. However, the practical application effectiveness of TEV detection is not satisfactory because of the lack of a TEV detection application method, i.e., a method with sufficient technical cognition and analysis. This paper proposes an innovative online PD detection system and a corresponding application strategy based on an intelligent feedback distributed TEV wireless sensor network, consisting of sensing, communication, and diagnosis layers. In the proposed system, the TEV signal or status data are wirelessly transmitted to the terminal following low-energy signal preprocessing and acquisition by TEV sensors. Then, a central server analyzes the correlation of the uploaded data and gives a fault warning level according to the quantity, trend, parallel analysis, and phase resolved partial discharge pattern recognition. In this way, a TEV detection system and strategy with distributed acquisition, unitized fault warning, and centralized diagnosis is realized. The proposed system has positive significance for reducing the fault rate of medium voltage switchgear and improving its operation and maintenance level.

Kinetic and catalytic performance of a BI-porous composite material in catalytic cracking and isomerisation reactions

KAUST Repository

Al-Khattaf, S.

2012-01-10

Catalytic behaviour of pure zeolite ZSM-5 and a bi-porous composite material (BCM) were investigated in transformation of m-xylene, while zeolite HY and the bi-porous composite were used in the cracking of 1,3,5-triisopropylbenzene (TIPB). The micro/mesoporous material was used to understand the effect of the presence of mesopores on these reactions. Various characterisation techniques, that is, XRD, SEM, TGA, FT-IR and nitrogen sorption measurements were applied for complete characterisation of the catalysts. Catalytic tests using CREC riser simulator showed that the micro/mesoporous composite catalyst exhibited higher catalytic activity as compared with the conventional microporous ZSM-5 and HY zeolite for transformation of m-xylene and for the catalytic cracking of TIPB, respectively. The outstanding catalytic reactivity of m-xylene and TIPB molecules were mainly attributed to the easier access of active sites provided by the mesopores. Apparent activation energies for the disappearance of m-xylene and TIPB over all catalysts were found to decrease in the order: EBCM>EZSM-5 and EBCM>EHY, respectively. © 2012 Canadian Society for Chemical Engineering.

A non-acid-assisted and non-hydroxyl-radical-related catalytic ozonation with ceria supported copper oxide in efficient oxalate degradation in water

KAUST Repository

Zhang, Tao; Li, Weiwei; Croue, Jean-Philippe

2012-01-01

with ozone. The optimum CuO loading amount was 12%. The molar ratio of oxalate removed/ozone consumption reached 0.84. The catalytic ozonation was most effective in a neutral pH range (6.7-7.9) and became ineffective when the water solution was acidic

Phase composition and catalytic properties of oxide multicomponent molybdenum-containing catalysts for partial oxidation of propylene

International Nuclear Information System (INIS)

Malakhov, V.V.; Vlasov, A.A.; Boldyreva, N.N.; Dovlitova, L.S.; Plyasova, L.M.; Andrushkevich, T.V.; Kuznetsova, T.G.

1996-01-01

The catalytic properties and phase composition of multicomponent molybdenum-containing catalyst treated under various redox conditions have been studied. The phase composition has been considered by the methods of X-ray phase analysis and noncalibrated methods of differentiating dissolution (DD). Using the DD method the data on element composition, stoichiometry and quantitative content of phases of complex molybdates have been obtained for the first time. Data on modification of basic phases of the catalyst-cobalt and iron molybdates - by other cations from its composition suggest that the mechanism of action of the multicomponent catalyst is defined by the properties of one or several formed modified phases combining all the functions of an effective catalyst. 18 refs., 7 figs., 2 tabs

Maximal Inequalities for Dependent Random Variables

DEFF Research Database (Denmark)

Hoffmann-Jorgensen, Jorgen

2016-01-01

Maximal inequalities play a crucial role in many probabilistic limit theorem; for instance, the law of large numbers, the law of the iterated logarithm, the martingale limit theorem and the central limit theorem. Let X-1, X-2,... be random variables with partial sums S-k = X-1 + ... + X-k. Then a......Maximal inequalities play a crucial role in many probabilistic limit theorem; for instance, the law of large numbers, the law of the iterated logarithm, the martingale limit theorem and the central limit theorem. Let X-1, X-2,... be random variables with partial sums S-k = X-1 + ... + X......-k. Then a maximal inequality gives conditions ensuring that the maximal partial sum M-n = max(1) (...

Non-Catalytic Functions of Pyk2 and Fyn Regulate Late Stage Adhesion in Human T Cells

Science.gov (United States)

Houtman, Jon C. D.

2012-01-01

T cell activation drives the protective immune response against pathogens, but is also critical for the development of pathological diseases in humans. Cytoskeletal changes are required for downstream functions in T cells, including proliferation, cytokine production, migration, spreading, and adhesion. Therefore, investigating the molecular mechanism of cytoskeletal changes is crucial for understanding the induction of T cell-driven immune responses and for developing therapies to treat immune disorders related to aberrant T cell activation. In this study, we used a plate-bound adhesion assay that incorporated near-infrared imaging technology to address how TCR signaling drives human T cell adhesion. Interestingly, we observed that T cells have weak adhesion early after TCR activation and that binding to the plate was significantly enhanced 30–60 minutes after receptor activation. This late stage of adhesion was mediated by actin polymerization but was surprisingly not dependent upon Src family kinase activity. By contrast, the non-catalytic functions of the kinases Fyn and Pyk2 were required for late stage human T cell adhesion. These data reveal a novel TCR-induced signaling pathway that controls cellular adhesion independent of the canonical TCR signaling cascade driven by tyrosine kinase activity. PMID:23300847

Response moments of dynamic systems under non-Gaussian random excitation by the equivalent non-Gaussian excitation method

International Nuclear Information System (INIS)

Tsuchida, Takahiro; Kimura, Koji

2016-01-01

Equivalent non-Gaussian excitation method is proposed to obtain the response moments up to the 4th order of dynamic systems under non-Gaussian random excitation. The non-Gaussian excitation is prescribed by the probability density and the power spectrum, and is described by an Ito stochastic differential equation. Generally, moment equations for the response, which are derived from the governing equations for the excitation and the system, are not closed due to the nonlinearity of the diffusion coefficient in the equation for the excitation even though the system is linear. In the equivalent non-Gaussian excitation method, the diffusion coefficient is replaced with the equivalent diffusion coefficient approximately to obtain a closed set of the moment equations. The square of the equivalent diffusion coefficient is expressed by a quadratic polynomial. In numerical examples, a linear system subjected to nonGaussian excitations with bimodal and Rayleigh distributions is analyzed by using the present method. The results show that the method yields the variance, skewness and kurtosis of the response with high accuracy for non-Gaussian excitation with the widely different probability densities and bandwidth. The statistical moments of the equivalent non-Gaussian excitation are also investigated to describe the feature of the method. (paper)

Optimal control of coupled parabolic-hyperbolic non-autonomous PDEs: infinite-dimensional state-space approach

Science.gov (United States)

Aksikas, I.; Moghadam, A. Alizadeh; Forbes, J. F.

2018-04-01

This paper deals with the design of an optimal state-feedback linear-quadratic (LQ) controller for a system of coupled parabolic-hypebolic non-autonomous partial differential equations (PDEs). The infinite-dimensional state space representation and the corresponding operator Riccati differential equation are used to solve the control problem. Dynamical properties of the coupled system of interest are analysed to guarantee the existence and uniqueness of the solution of the LQ-optimal control problem and also to guarantee the exponential stability of the closed-loop system. Thanks to the eigenvalues and eigenfunctions of the parabolic operator and also the fact that the hyperbolic-associated operator Riccati differential equation can be converted to a scalar Riccati PDE, an algorithm to solve the LQ control problem has been presented. The results are applied to a non-isothermal packed-bed catalytic reactor. The LQ optimal controller designed in the early portion of the paper is implemented for the original non-linear model. Numerical simulations are performed to show the controller performances.

Synthesis, characterization and catalytic properties of nanocrystaline Y{sub 2}O{sub 3}-coated TiO{sub 2} in the ethanol dehydration reaction

Energy Technology Data Exchange (ETDEWEB)

Fajardo, Humberto Vieira [Universidade Federal de Ouro Preto (UFOP), MG (Brazil). Departamento de Quimica; Longo, Elson [Universidade Estadual Paulista (UNESP), Araraquara, SP (Brazil). Departamento de Fisico-Quimica; Leite, Edson Roberto; Libanori, Rafael [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil). Departamento de Quimica; Probst, Luiz Fernando Dias [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil). Departamento de Quimica; Carreno, Neftali Lenin Villarreal [Universidade Federal de Pelotas (UFPel), RS (Brazil). Departamento de Quimica Analitica e Inorganica

2012-03-15

In the present study, TiO{sub 2} nano powder was partially coated with Y{sub 2}O{sub 3} precursors generated by a sol-gel modified route. The system of nanocoated particles formed an ultra thin structure on the TiO{sub 2} surfaces. The modified nanoparticles were characterized by high resolution transmission electron microscopy (HR-TEM), X-ray diffraction (XRD) analysis, Zeta potential and surface area through N{sub 2} physisorption measurements. Bioethanol dehydration was used as a probe reaction to investigate the modifications on the nanoparticles surface. The process led to the obtainment of nanoparticles with important surface characteristics and catalytic behavior in the bioethanol dehydration reaction, with improved activity and particular selectivity in comparison to their non-coated analogs. The ethylene production was disfavored and selectivity toward acetaldehyde, hydrogen and ethane increased over modified nanoparticles. (author)

On the Shaker Simulation of Wind-Induced Non-Gaussian Random Vibration

Directory of Open Access Journals (Sweden)

Fei Xu

2016-01-01

Full Text Available Gaussian signal is produced by ordinary random vibration controllers to test the products in the laboratory, while the field data is usually non-Gaussian. Two methodologies are presented in this paper for shaker simulation of wind-induced non-Gaussian vibration. The first methodology synthesizes the non-Gaussian signal offline and replicates it on the shaker in the Time Waveform Replication (TWR mode. A new synthesis method is used to model the non-Gaussian signal as a Gaussian signal multiplied by an amplitude modulation function (AMF. A case study is presented to show that the synthesized non-Gaussian signal has the same power spectral density (PSD, probability density function (PDF, and loading cycle distribution (LCD as the field data. The second methodology derives a damage equivalent Gaussian signal from the non-Gaussian signal based on the fatigue damage spectrum (FDS and the extreme response spectrum (ERS and reproduces it on the shaker in the closed-loop frequency domain control mode. The PSD level and the duration time of the derived Gaussian signal can be manipulated for accelerated testing purpose. A case study is presented to show that the derived PSD matches the damage potential of the non-Gaussian environment for both fatigue and peak response.

Synthesis of carbon-supported copper catalyst and its catalytic performance in methanol dehydrogenation

Energy Technology Data Exchange (ETDEWEB)

Shelepova, Ekaterina V. [Boreskov Institute of Catalysis SB RAS, pr. Ac. Lavrentieva, 5, Novosibirsk, 630090 (Russian Federation); National Research Tomsk Polytechnic University, Lenin av., 30, Tomsk, 634050 (Russian Federation); Vedyagin, Aleksey A., E-mail: vedyagin@catalysis.ru [Boreskov Institute of Catalysis SB RAS, pr. Ac. Lavrentieva, 5, Novosibirsk, 630090 (Russian Federation); National Research Tomsk Polytechnic University, Lenin av., 30, Tomsk, 634050 (Russian Federation); Ilina, Ludmila Yu.; Nizovskii, Alexander I. [Boreskov Institute of Catalysis SB RAS, pr. Ac. Lavrentieva, 5, Novosibirsk, 630090 (Russian Federation); Tsyrulnikov, Pavel G. [Institute of Hydrocarbon Processing SB RAS, Neftezavodskaya st., 54, Omsk, 644040 (Russian Federation)

2017-07-01

Highlights: • Carbon-supported copper catalyst was studied in dehydrogenation of methanol. • Reduction temperature affected size of Cu particles and Cu{sup 0}/Cu{sup 2+} ratio. • Reduction at 400 °C was required to obtain high methyl formate yield. - Abstract: Carbon-supported copper catalyst was prepared by incipient wetness impregnation of Sibunit with an aqueous solution of copper nitrate. Copper loading was 5 wt.%. Temperature of reductive pretreatment was varied within a range of 200–400 °C. The samples were characterized by transmission electron microscopy, X-ray diffraction analysis, X-ray photoelectron and X-ray absorption spectroscopies. Catalytic activity of the samples was studied in a reaction of methanol dehydrogenation. Silica-based catalyst with similar copper loading was used as a reference. It was found that copper is distributed over the surface of support in the form of metallic and partially oxidized particles of about 12–17 nm in size. Diminished interaction of copper with support was supposed to be responsible for high catalytic activity.

H$_2$ Production via Ammonia Decomposition Using Non-Noble Metal Catalysts: A Review

OpenAIRE

Bell, Tamsin; Torrente-Murciano, L

2016-01-01

The wide-spread implementation of the so-called hydrogen economy is currently partially limited by an economically feasible way of storing hydrogen. In this context, ammonia has been commonly presented as a viable option for chemical storage due its high hydrogen content (17.6 wt%). However, its use as an energy carrier requires the development of catalytic systems capable of releasing hydrogen at adequate rates and conditions. At the moment, the most active catalytic systems for the decompos...

Engineering reactors for catalytic reactions

Indian Academy of Sciences (India)

Extensive studies have been conducted to establish sound basis for design and engineering of reactors for practising such catalytic reactions and for realizing improvements in reactor performance. In this article, application of recent (and not so recent) developments in engineering reactors for catalytic reactions is ...

Non-fragile observer design for discrete-time genetic regulatory networks with randomly occurring uncertainties

International Nuclear Information System (INIS)

Banu, L Jarina; Balasubramaniam, P

2015-01-01

This paper investigates the problem of non-fragile observer design for a class of discrete-time genetic regulatory networks (DGRNs) with time-varying delays and randomly occurring uncertainties. A non-fragile observer is designed, for estimating the true concentration of mRNAs and proteins from available measurement outputs. One important feature of the results obtained that are reported here is that the parameter uncertainties are assumed to be random and their probabilities of occurrence are known a priori. On the basis of the Lyapunov–Krasovskii functional approach and using a convex combination technique, a delay-dependent estimation criterion is established for DGRNs in terms of linear matrix inequalities (LMIs) that can be efficiently solved using any available LMI solver. Finally numerical examples are provided to substantiate the theoretical results. (paper)

A bioinspired catalytic aerobic oxidative C-H functionalization of primary aliphatic amines: synthesis of 1,2-disubstituted benzimidazoles.

Science.gov (United States)

Nguyen, Khac Minh Huy; Largeron, Martine

2015-09-01

Aerobic oxidative CH functionalization of primary aliphatic amines has been accomplished with a biomimetic cooperative catalytic system to furnish 1,2-disubstituted benzimidazoles that play an important role as drug discovery targets. This one-pot atom-economical multistep process, which proceeds under mild conditions, with ambient air and equimolar amounts of each coupling partner, constitutes a convenient environmentally friendly strategy to functionalize non-activated aliphatic amines that remain challenging substrates for non-enzymatic catalytic aerobic systems. © 2015 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA. This is an open access article under the terms of Creative Commons Attribution NonCommercial-NoDerivs License, which permits use and distribution in any medium, provided the original work is properly cited, the use is non-commercial and no modifications or adaptations are made.

Reaction Current Phenomenon in Bifunctional Catalytic Metal-Semiconductor Nanostructures

Science.gov (United States)

Hashemian, Mohammad Amin

Energy transfer processes accompany every elementary step of catalytic chemical processes on material surface including molecular adsorption and dissociation on atoms, interactions between intermediates, and desorption of reaction products from the catalyst surface. Therefore, detailed understanding of these processes on the molecular level is of great fundamental and practical interest in energy-related applications of nanomaterials. Two main mechanisms of energy transfer from adsorbed particles to a surface are known: (i) adiabatic via excitation of quantized lattice vibrations (phonons) and (ii) non-adiabatic via electronic excitations (electron/hole pairs). Electronic excitations play a key role in nanocatalysis, and it was recently shown that they can be efficiently detected and studied using Schottky-type catalytic nanostructures in the form of measureable electrical currents (chemicurrents) in an external electrical circuit. These nanostructures typically contain an electrically continuous nanocathode layers made of a catalytic metal deposited on a semiconductor substrate. The goal of this research is to study the direct observations of hot electron currents (chemicurrents) in catalytic Schottky structures, using a continuous mesh-like Pt nanofilm grown onto a mesoporous TiO2 substrate. Such devices showed qualitatively different and more diverse signal properties, compared to the earlier devices using smooth substrates, which could only be explained on the basis of bifunctionality. In particular, it was necessary to suggest that different stages of the reaction are occurring on both phases of the catalytic structure. Analysis of the signal behavior also led to discovery of a formerly unknown (very slow) mode of the oxyhydrogen reaction on the Pt/TiO2(por) system occurring at room temperature. This slow mode was producing surprisingly large stationary chemicurrents in the range 10--50 microA/cm2. Results of the chemicurrent measurements for the bifunctional

PARAMETRIC IDENTIFICATION OF STOCHASTIC SYSTEM BY NON-GRADIENT RANDOM SEARCHING

Directory of Open Access Journals (Sweden)

A. A. Lobaty

2017-01-01

Full Text Available At this moment we know a great variety of identification objects, tasks and methods and its significance is constantly increasing in various fields of science and technology.  The identification problem is dependent on a priori information about identification object, besides that  the existing approaches and methods of identification are determined by the form of mathematical models (deterministic, stochastic, frequency, temporal, spectral etc.. The paper considers a problem for determination of system parameters  (identification object which is assigned by the stochastic mathematical model including random functions of time. It has been shown  that while making optimization of the stochastic systems subject to random actions deterministic methods can be applied only for a limited approximate optimization of the system by taking into account average random effects and fixed structure of the system. The paper proposes an algorithm for identification of  parameters in a mathematical model of  the stochastic system by non-gradient random searching. A specific  feature  of the algorithm is its applicability  practically to mathematic models of any type because the applied algorithm does not depend on linearization and differentiability of functions included in the mathematical model of the system. The proposed algorithm  ensures searching of  an extremum for the specified quality criteria in terms of external uncertainties and limitations while using random searching of parameters for a mathematical model of the system. The paper presents results of the investigations on operational capability of the considered identification method  while using mathematical simulation of hypothetical control system with a priori unknown parameter values of the mathematical model. The presented results of the mathematical simulation obviously demonstrate the operational capability of the proposed identification method.

Synergetic mechanism of methanol–steam reforming reaction in a catalytic reactor with electric discharges

International Nuclear Information System (INIS)

Kim, Taegyu; Jo, Sungkwon; Song, Young-Hoon; Lee, Dae Hoon

2014-01-01

Highlights: • Methanol–steam reforming was performed on Cu catalysts under an electric discharge. • Discharge had a synergetic effect on the catalytic reaction for methanol conversion. • Discharge lowered the temperature for catalyst activation or light off. • Discharge controlled the yield and selectivity of species in a reforming process. • Adsorption triggered by a discharge was a possible mechanism for a synergetic effect. - Abstract: Methanol–steam reforming was performed on Cu/ZnO/Al 2 O 3 catalysts under an electric discharge. The discharge occurred between the electrodes where the catalysts were packed. The electric discharge was characterized by the discharge voltage and electric power to generate the discharge. The existence of a discharge had a synergetic effect on the catalytic reaction for methanol conversion. The electric discharge provided modified reaction paths resulting in a lower temperature for catalyst activation or light off. The discharge partially controlled the yield and selectivity of species in a reforming process. The aspect of control was examined in view of the reaction kinetics. The possible mechanisms for the synergetic effect between the catalytic reaction and electric discharge on methanol–steam reforming were addressed. A discrete reaction path, particularly adsorption triggered by an electric discharge, was suggested to be the most likely mechanism for the synergetic effect. These results are expected to provide a guide for understanding the plasma–catalyst hybrid reaction

Catalytic Conversion of Biomass Pyrolysis Vapours over Sodium-Based Catalyst; A Study on teh State of Sodium on the Catalyst

NARCIS (Netherlands)

Nguyen, T.S.; Lefferts, Leonardus; Gupta, K.B. Sai Sankar; Seshan, Kulathuiyer

2015-01-01

In situ upgrading of biomass pyrolysis vapours over Na2CO3/γ-Al2O3 catalysts was studied in a laboratory-scale fixed-bed reactor at 500 °C. Catalytic oil exhibits a significant improvement over its non-catalytic counterpart, such as lower oxygen content (12.3 wt % compared to 42.1 wt %), higher

Extinction of laminar partially premixed flames

Energy Technology Data Exchange (ETDEWEB)

Aggarwal, Suresh K. [Department of Mechanical and Industrial Engineering, University of Illinois at Chicago, 842 W. Taylor Street, Room 2039, MC-251, Chicago, IL 60607-7022 (United States)

2009-12-15

Flame extinction represents one of the classical phenomena in combustion science. It is important to a variety of combustion systems in transportation and power generation applications. Flame extinguishment studies are also motivated from the consideration of fire safety and suppression. Such studies have generally considered non-premixed and premixed flames, although fires can often originate in a partially premixed mode, i.e., fuel and oxidizer are partially premixed as they are transported to the reaction zone. Several recent investigations have considered this scenario and focused on the extinction of partially premixed flames (PPFs). Such flames have been described as hybrid flames possessing characteristics of both premixed and non-premixed flames. This paper provides a review of studies dealing with the extinction of PPFs, which represent a broad family of flames, including double, triple (tribrachial), and edge flames. Theoretical, numerical and experimental studies dealing with the extinction of such flames in coflow and counterflow configurations are discussed. Since these flames contain both premixed and non-premixed burning zones, a brief review of the dilution-induced extinction of premixed and non-premixed flames is also provided. For the coflow configuration, processes associated with flame liftoff and blowout are described. Since lifted non-premixed jet flames often contain a partially premixed or an edge-flame structure prior to blowout, the review also considers such flames. While the perspective of this review is broad focusing on the fundamental aspects of flame extinction and blowout, results mostly consider flame extinction caused by the addition of a flame suppressant, with relevance to fire suppression on earth and in space environment. With respect to the latter, the effect of gravity on the extinction of PPFs is discussed. Future research needs are identified. (author)

Enhanced sensitivity in non-enzymatic glucose detection by improved growth kinetics of Ni-based nanostructures

Science.gov (United States)

Urso, M.; Pellegrino, G.; Strano, V.; Bruno, E.; Priolo, F.; Mirabella, S.

2018-04-01

Ni-based nanostructures are attractive catalytic materials for many electrochemical applications, among which are non-enzymatic sensing, charge storage, and water splitting. In this work, we clarify the synthesis kinetics of Ni(OH)2/NiOOH nanowalls grown by chemical bath deposition at room temperature and at 50 °C. We applied the results to non-enzymatic glucose sensing, reaching a highest sensitivity of 31 mA cm-2mM-1. Using scanning electron microscopy, x-ray diffraction analysis and Rutherford backscattering spectrometry we found that the growth occurs through two regimes: first, a quick random growth leading to disordered sheets of Ni oxy-hydroxide, followed by a slower growth of well-aligned sheets of Ni hydroxide. A high growth temperature (50 °C), leading mainly to well-aligned sheets, offers superior electrochemical properties in terms of charge storage, charge carrier transport and catalytic action, as confirmed by cyclic voltammetry and electrochemical impedance spectroscopy analyses. The reported results on the optimization and application of low-cost synthesis of these Ni-based nanostructures have a large potential for application in catalysis, (bio)sensing, and supercapacitors areas.

Interpolation between Airy and Poisson statistics for unitary chiral non-Hermitian random matrix ensembles

International Nuclear Information System (INIS)

Akemann, G.; Bender, M.

2010-01-01

We consider a family of chiral non-Hermitian Gaussian random matrices in the unitarily invariant symmetry class. The eigenvalue distribution in this model is expressed in terms of Laguerre polynomials in the complex plane. These are orthogonal with respect to a non-Gaussian weight including a modified Bessel function of the second kind, and we give an elementary proof for this. In the large n limit, the eigenvalue statistics at the spectral edge close to the real axis are described by the same family of kernels interpolating between Airy and Poisson that was recently found by one of the authors for the elliptic Ginibre ensemble. We conclude that this scaling limit is universal, appearing for two different non-Hermitian random matrix ensembles with unitary symmetry. As a second result we give an equivalent form for the interpolating Airy kernel in terms of a single real integral, similar to representations for the asymptotic kernel in the bulk and at the hard edge of the spectrum. This makes its structure as a one-parameter deformation of the Airy kernel more transparent.

Achalasia-Specific Quality of Life After Pneumatic Dilation or Laparoscopic Heller Myotomy With Partial Fundoplication: A Multicenter, Randomized Clinical Trial.

Science.gov (United States)

Chrystoja, Caitlin C; Darling, Gail E; Diamant, Nicholas E; Kortan, Paul P; Tomlinson, George A; Deitel, Wayne; Laporte, Audrey; Takata, Julie; Urbach, David R

2016-11-01

Achalasia is a chronic, progressive, and incurable esophageal motility disease. There is clinical uncertainty about which treatment should be recommended as first-line therapy. Our objective was to evaluate the effectiveness of pneumatic dilation compared with laparoscopic Heller myotomy with partial fundoplication in improving achalasia-specific quality of life. This was a prospective, multicenter, randomized trial at five academic hospitals in Canada. Fifty previously untreated adults with a clinical diagnosis of primary achalasia, confirmed by manometric testing, were enrolled between November 2005 and March 2010, and followed for 5 years after treatment. Randomization was stratified by site, in random blocks of size four and with balanced allocation. Patients were treated with pneumatic dilation or laparoscopic Heller myotomy with partial fundoplication. The primary outcome was the difference between the treatments in the mean improvement of the achalasia severity questionnaire (ASQ) score at 1 year from baseline. Prespecified secondary outcomes included general and gastrointestinal quality of life, symptoms, esophageal physiology measures (lower esophageal sphincter relaxation and pressure, esophageal emptying, abnormal esophageal acid exposure), complications, and incidence of retreatment. Functional and imaging studies were performed blinded and all outcome assessors were blinded. There were no significant differences between treatments in the improvement of ASQ score at 1 year from baseline (27.5 points in the Heller myotomy arm vs. 20.2 points in the pneumatic dilation arm; difference 7.3 points, 95% confidence interval -4.7 to 19.3; P=0.23). There were no differences between treatments in improvement of symptoms, general and gastrointestinal quality of life, or measures of esophageal physiology. Improvements in ASQ score diminished over time for both interventions. At 5 years, there were no differences between treatments in improvement of ASQ score

[Acrylic resin removable partial dentures].

Science.gov (United States)

de Baat, C; Witter, D J; Creugers, N H J

2011-01-01

An acrylic resin removable partial denture is distinguished from other types of removable partial dentures by an all-acrylic resin base which is, in principle, solely supported by the edentulous regions of the tooth arch and in the maxilla also by the hard palate. When compared to the other types of removable partial dentures, the acrylic resin removable partial denture has 3 favourable aspects: the economic aspect, its aesthetic quality and the ease with which it can be extended and adjusted. Disadvantages are an increased risk of caries developing, gingivitis, periodontal disease, denture stomatitis, alveolar bone reduction, tooth migration, triggering of the gag reflex and damage to the acrylic resin base. Present-day indications are ofa temporary or palliative nature or are motivated by economic factors. Special varieties of the acrylic resin removable partial denture are the spoon denture, the flexible denture fabricated of non-rigid acrylic resin, and the two-piece sectional denture. Furthermore, acrylic resin removable partial dentures can be supplied with clasps or reinforced by fibers or metal wires.

Efficacy of orally administered prednisolone versus partial endodontic treatment on pain reduction in emergency care of acute irreversible pulpitis of mandibular molars: study protocol for a randomized controlled trial.

Science.gov (United States)

Kérourédan, Olivia; Jallon, Léonard; Perez, Paul; Germain, Christine; Péli, Jean-François; Oriez, Dominique; Fricain, Jean-Christophe; Arrivé, Elise; Devillard, Raphaël

2017-03-28

Irreversible pulpitis is a highly painful inflammatory condition of the dental pulp which represents a common dental emergency. Recommended care is partial endodontic treatment. The dental literature reports major difficulties in achieving adequate analgesia to perform this emergency treatment, especially in the case of mandibular molars. In current practice, short-course, orally administered corticotherapy is used for the management of oral pain of inflammatory origin. The efficacy of intraosseous local steroid injections for irreversible pulpitis in mandibular molars has already been demonstrated but resulted in local comorbidities. Oral administration of short-course prednisolone is simple and safe but its efficacy to manage pain caused by irreversible pulpitis has not yet been demonstrated. This trial aims to evaluate the noninferiority of short-course, orally administered corticotherapy versus partial endodontic treatment for the emergency care of irreversible pulpitis in mandibular molars. This study is a noninferiority, open-label, randomized controlled clinical trial conducted at the Bordeaux University Hospital. One hundred and twenty subjects will be randomized in two 1:1 parallel arms: the intervention arm will receive one oral dose of prednisolone (1 mg/kg) during the emergency visit, followed by one morning dose each day for 3 days and the reference arm will receive partial endodontic treatment. Both groups will receive planned complete endodontic treatment 72 h after enrollment. The primary outcome is the proportion of patients with pain intensity below 5 on a Numeric Scale 24 h after the emergency visit. Secondary outcomes include comfort during care, the number of injected anesthetic cartridges when performing complete endodontic treatment, the number of antalgic drugs and the number of patients coming back for consultation after 72 h. This randomized trial will assess the ability of short-term corticotherapy to reduce pain in irreversible

Synthesis, spectroscopic characterization and catalytic oxidation ...

Indian Academy of Sciences (India)

were characterized by infrared, electronic, electron paramagnetic resonance ... The catalytic oxidation property of ruthenium(III) complexes were also ... cies at room temperature. ..... aldehyde part of Schiff base ligands, catalytic activ- ity of new ...

Invariant and partially-invariant solutions of the equations describing a non-stationary and isentropic flow for an ideal and compressible fluid in (3 + 1) dimensions

Science.gov (United States)

Grundland, A. M.; Lalague, L.

1996-04-01

This paper presents a new method of constructing, certain classes of solutions of a system of partial differential equations (PDEs) describing the non-stationary and isentropic flow for an ideal compressible fluid. A generalization of the symmetry reduction method to the case of partially-invariant solutions (PISs) has been formulated. We present a new algorithm for constructing PISs and discuss in detail the necessary conditions for the existence of non-reducible PISs. All these solutions have the defect structure 0305-4470/29/8/019/img1 and are computed from four-dimensional symmetric subalgebras. These theoretical considerations are illustrated by several examples. Finally, some new classes of invariant solutions obtained by the symmetry reduction method are included. These solutions represent central, conical, rational, spherical, cylindrical and non-scattering double waves.

The Mobility Enhancement of Indium Gallium Zinc Oxide Transistors via Low-temperature Crystallization using a Tantalum Catalytic Layer

OpenAIRE

Shin, Yeonwoo; Kim, Sang Tae; Kim, Kuntae; Kim, Mi Young; Oh, Saeroonter; Jeong, Jae Kyeong

2017-01-01

High-mobility indium gallium zinc oxide (IGZO) thin-film transistors (TFTs) are achieved through low-temperature crystallization enabled via a reaction with a transition metal catalytic layer. For conventional amorphous IGZO TFTs, the active layer crystallizes at thermal annealing temperatures of 600??C or higher, which is not suitable for displays using a glass substrate. The crystallization temperature is reduced when in contact with a Ta layer, where partial crystallization at the IGZO bac...

MINIMUM ENTROPY DECONVOLUTION OF ONE-AND MULTI-DIMENSIONAL NON-GAUSSIAN LINEAR RANDOM PROCESSES

Institute of Scientific and Technical Information of China (English)

程乾生

1990-01-01

The minimum entropy deconvolution is considered as one of the methods for decomposing non-Gaussian linear processes. The concept of peakedness of a system response sequence is presented and its properties are studied. With the aid of the peakedness, the convergence theory of the minimum entropy deconvolution is established. The problem of the minimum entropy deconvolution of multi-dimensional non-Gaussian linear random processes is first investigated and the corresponding theory is given. In addition, the relation between the minimum entropy deconvolution and parameter method is discussed.

Catalytic exhaust control

Energy Technology Data Exchange (ETDEWEB)

Heinemann, H

1973-09-01

Recent achievements and problems in the development of exhaust control devices in the USA are reviewed. To meet the 1976 emission standards, catalytic systems for the oxidation of carbon monoxide and hydrocarbons and for the reduction of nitrogen oxides to nitrogen and water are needed. While oxidizing catalysts using platinum, palladium, copper, vanadium, and chromium appplied on alumina or ceramic materials are more or less effective in emission control, there are no catalytic devices for the reduction of nitrogen oxides with the required useful life of 25,000 to 50,000 miles as yet available. In the case of platinum catalysts on monolithic supports, the operating temperature of 650 to 750/sup 0/C as required for the oxidation process may cause inactivation of the catalysts and fusion of the support material. The oxidation of CO and hydrocarbons is inhibited by high concentrations of CO, nitric oxide, and hydrocarbons. The use of catalytic converters requires the use of lead-free or low-lead gasoline. The nitrogen oxides conversion efficiency is considerably influenced by the oxygen-to-CO ratio of the exhaust gas, which makes limitation of this ratio necessary.

Catalytic Wittig and aza-Wittig reactions

Directory of Open Access Journals (Sweden)

Zhiqi Lao

2016-11-01

Full Text Available This review surveys the literature regarding the development of catalytic versions of the Wittig and aza-Wittig reactions. The first section summarizes how arsenic and tellurium-based catalytic Wittig-type reaction systems were developed first due to the relatively easy reduction of the oxides involved. This is followed by a presentation of the current state of the art regarding phosphine-catalyzed Wittig reactions. The second section covers the field of related catalytic aza-Wittig reactions that are catalyzed by both phosphine oxides and phosphines.

Efficient catalytic combustion in integrated micropellistors

International Nuclear Information System (INIS)

Bársony, I; Ádám, M; Fürjes, P; Dücső, Cs; Lucklum, R; Hirschfelder, M; Kulinyi, S

2009-01-01

This paper analyses two of the key issues of the development of catalytic combustion-type sensors: the selection and production of active catalytic particles on the micropellistor surface as well as the realization of a reliable thermal conduction between heater element and catalytic surface, for the sensing of temperature increase produced by the combustion. The report also demonstrates that chemical sensor product development by a MEMS process is a continuous struggle for elimination of all uncertainties influencing reliability and sensitivity of the final product

Adsorbent catalytic nanoparticles and methods of using the same

Energy Technology Data Exchange (ETDEWEB)

Slowing, Igor Ivan; Kandel, Kapil

2017-01-31

The present invention provides an adsorbent catalytic nanoparticle including a mesoporous silica nanoparticle having at least one adsorbent functional group bound thereto. The adsorbent catalytic nanoparticle also includes at least one catalytic material. In various embodiments, the present invention provides methods of using and making the adsorbent catalytic nanoparticles. In some examples, the adsorbent catalytic nanoparticles can be used to selectively remove fatty acids from feedstocks for biodiesel, and to hydrotreat the separated fatty acids.

Lattice Boltzmann simulation of endothermal catalytic reaction in catalyst porous media

International Nuclear Information System (INIS)

Li Xunfeng; Cai Jun; Xin Fang; Huai Xiulan; Guo Jiangfeng

2013-01-01

Gas catalytic reaction in a fixed bed reactor is a general process in chemical industry. The chemical reaction process involves the complex multi-component flow, heat and mass transfer coupling chemical reaction in the catalyst porous structure. The lattice Boltzmann method is developed to simulate the complex process of the surface catalytic reaction in the catalyst porous media. The non-equilibrium extrapolation method is used to treat the boundaries. The porous media is structured by Sierpinski carpet fractal structure. The velocity correction is adopted on the reaction surface. The flow, temperature and concentration fields calculated by the lattice Boltzmann method are compared with those computed by the CFD software. The effects of the inlet velocity, porosity and inlet components ratio on the conversion are also studied. Highlights: ► LBM is developed to simulate the surface catalytic reaction. ► The Sierpinski carpet structure is used to construct the porous media. ► The LBM results are in agreement with the CFD predictions. ► Velocity, temperature and concentration fields are obtained. ► Effects of the velocity, porosity and concentration on conversion are analyzed.

On the remarkable spectrum of a non-Hermitian random matrix model

International Nuclear Information System (INIS)

Holz, D E; Orland, H; Zee, A

2003-01-01

A non-Hermitian random matrix model proposed a few years ago has a remarkably intricate spectrum. Various attempts have been made to understand the spectrum, but even its dimension is not known. Using the Dyson-Schmidt equation, we show that the spectrum consists of a non-denumerable set of lines in the complex plane. Each line is the support of the spectrum of a periodic Hamiltonian, obtained by the infinite repetition of any finite sequence of the disorder variables. Our approach is based on the 'theory of words'. We make a complete study of all four-letter words. The spectrum is complicated because our matrix contains everything that will ever be written in the history of the universe, including this particular paper

Methane partial oxidation over a LaCr0.85Ru0.15O3 catalyst : Characterization, activity tests and kinetic modeling

NARCIS (Netherlands)

Melchiori, T.; Di Felice, L.; Mota, N.; Navarro, R.M.; Fierro, J.L.G.; Sint Annaland, van M.; Gallucci, F.

2014-01-01

A new LaCr0.85Ru0.15O3 perovskite-type catalyst for CH4 partial oxidation with a high activity and selectivity for syngas with good thermal stability and resistance against coking has been developed. In this paper, the catalyst preparation method, catalyst characterization, results of catalytic

Catalytic pyrolysis of hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Vail' eva, N A; Buyanov, R A

1979-01-01

Catalytic pyrolysis of petroleum fractions (undecane) was performed with the object of clarifying such questions as the mechanism of action of the catalyst, the concepts of activity and selectivity of the catalyst, the role of transport processes, the temperature ranges and limitations of the catalytic process, the effect of the catalyst on secondary processes, and others. Catalysts such as quartz, MgO, Al/sub 2/O/sub 3/, were used. Analysis of the experimental findings and the fact that the distribution of products is independent of the nature of the surface, demonstrate that the pyrolysis of hydrocarbons in the presence of catalysts is based on the heterogeneous-homogeneous radical-chain mechanism of action, and that the role of the catalysts reduces to increasing the concentration of free radicals. The concept of selectivity cannot be applied to catalysts here, since they do not affect the mechanism of the unfolding of the process of pyrolysis and their role consists solely in initiating the process. In catalytic pyrolysis the concepts of kinetic and diffusive domains of unfolding of the catalytic reaction do not apply, and only the outer surface of the catalyst is engaged, whereas the inner surface merely promotes deletorious secondary processes reducing the selectivity of the process and the activity of the catalyst. 6 references, 2 figures.

Validation of the k-filtering technique for a signal composed of random-phase plane waves and non-random coherent structures

Directory of Open Access Journals (Sweden)

O. W. Roberts

2014-12-01

Full Text Available Recent observations of astrophysical magnetic fields have shown the presence of fluctuations being wave-like (propagating in the plasma frame and those described as being structure-like (advected by the plasma bulk velocity. Typically with single-spacecraft missions it is impossible to differentiate between these two fluctuations, due to the inherent spatio-temporal ambiguity associated with a single point measurement. However missions such as Cluster which contain multiple spacecraft have allowed for temporal and spatial changes to be resolved, using techniques such as k filtering. While this technique does not assume Taylor's hypothesis it requires both weak stationarity of the time series and that the fluctuations can be described by a superposition of plane waves with random phases. In this paper we test whether the method can cope with a synthetic signal which is composed of a combination of non-random-phase coherent structures with a mean radius d and a mean separation λ, as well as plane waves with random phase.

Shape-dependent plasma-catalytic activity of ZnO nanomaterials coated on porous ceramic membrane for oxidation of butane.

Science.gov (United States)

Sanjeeva Gandhi, M; Mok, Young Sun

2014-12-01

In order to explore the effects of the shape of ZnO nanomaterials on the plasma-catalytic decomposition of butane and the distribution of byproducts, three types of ZnO nanomaterials (nanoparticles (NPs), nanorods (NRs) and nanowires (NWs)) were prepared and coated on multi-channel porous alumina ceramic membrane. The structures and morphologies of the nanomaterials were confirmed by X-ray diffraction method and scanning electron microscopy. The observed catalytic activity of ZnO in the oxidative decomposition of butane was strongly shape-dependent. It was found that the ZnO NWs exhibited higher catalytic activity than the other nanomaterials and could completely oxidize butane into carbon oxides (COx). When using the bare or ZnO NPs-coated ceramic membrane, several unwanted partial oxidation and decomposition products like acetaldehyde, acetylene, methane and propane were identified during the decomposition of butane. When the ZnO NWs- or ZnO NRs-coated membrane was used, however, the formation of such unwanted byproducts except methane was completely avoided, and full conversion into COx was achieved. Better carbon balance and COx selectivity were obtained with the ZnO NWs and NRs than with the NPs. Copyright © 2014 Elsevier Ltd. All rights reserved.

Catalytic converters in the fireplace

International Nuclear Information System (INIS)

Kouki, J.

1995-01-01

In addition to selecting the appropriate means of heating and using dry fuel, the amount of harmful emissions contained by flue gases produced by fireplaces can be reduced by technical means. One such option is to use an oxidising catalytic converter. Tests at TTS Institute's Heating Studies Experimental Station have focused on two such converters (dense and coarse) mounted in light-weight iron heating stoves. The ability of the dense catalytic converter to oxidise carbon monoxide gases proved to be good. The concentration of carbon monoxide in the flue gases was reduced by as much as 90 %. Measurements conducted by VTT (Technical Research Centre of Finland) showed that the conversion of other gases, e.g. of methane, was good. The exhaust resistance caused by the dense converter was so great as to necessitate the mounting of a fluegas evacuation fan in the chimney for the purpose of creating sufficient draught. When relying on natural draught, the dense converter requires a chimney of at least 7 metres and a by-pass connection while the fire is being lit. In addition, the converter will have to be constructed to be less dense and this will mean that it's capability to oxidise non-combusted gases will be reduced. The coarse converter did not impair the draught but it's oxidising property was insufficient. With the tests over, the converter was not observed to have become blocked up by impurities

Compatriot partiality and cosmopolitan justice: Can we justify compatriot partiality within the cosmopolitan framework?

Directory of Open Access Journals (Sweden)

Rachelle Bascara

2016-10-01

Full Text Available This paper shows an alternative way in which compatriot partiality could be justified within the framework of global distributive justice. Philosophers who argue that compatriot partiality is similar to racial partiality capture something correct about compatriot partiality. However, the analogy should not lead us to comprehensively reject compatriot partiality. We can justify compatriot partiality on the same grounds that liberation movements and affirmative action have been justified. Hence, given cosmopolitan demands of justice, special consideration for the economic well-being of your nation as a whole is justified if and only if the country it identifies is an oppressed developing nation in an unjust global order.This justification is incomplete. We also need to say why Person A, qua national of Country A, is justified in helping her compatriots in Country A over similarly or slightly more oppressed non-compatriots in Country B. I argue that Person A’s partiality towards her compatriots admits further vindication because it is part of an oppressed group’s project of self-emancipation, which is preferable to paternalistic emancipation.Finally, I identify three benefits in my justification for compatriot partiality. First, I do not offer a blanket justification for all forms of compatriot partiality. Partiality between members of oppressed groups is only a temporary effective measure designed to level an unlevel playing field. Second, because history attests that sovereign republics could arise as a collective response to colonial oppression, justifying compatriot partiality on the grounds that I have identified is conducive to the development of sovereignty and even democracy in poor countries, thereby avoiding problems of infringement that many humanitarian poverty alleviation efforts encounter. Finally, my justification for compatriot partiality complies with the implicit cosmopolitan commitment to the realizability of global justice

Computer-based instrumentation for partial discharge detection in GIS

International Nuclear Information System (INIS)

Md Enamul Haque; Ahmad Darus; Yaacob, M.M.; Halil Hussain; Feroz Ahmed

2000-01-01

Partial discharge is one of the prominent indicators of defects and insulation degradation in a Gas Insulated Switchgear (GIS). Partial discharges (PD) have a harmful effect on the life of insulation of high voltage equipment. The PD detection using acoustic technique and subsequent analysis is currently an efficient method of performing non-destructive testing of GIS apparatus. A low cost PC-based acoustic PD detection instrument has been developed for the non-destructive diagnosis of GIS. This paper describes the development of a PC-based instrumentation system for partial discharge detection in GIS and some experimental results have also presented. (Author)

Catalytic cracking models developed for predictive control purposes

Directory of Open Access Journals (Sweden)

Dag Ljungqvist

1993-04-01

Full Text Available The paper deals with state-space modeling issues in the context of model-predictive control, with application to catalytic cracking. Emphasis is placed on model establishment, verification and online adjustment. Both the Fluid Catalytic Cracking (FCC and the Residual Catalytic Cracking (RCC units are discussed. Catalytic cracking units involve complex interactive processes which are difficult to operate and control in an economically optimal way. The strong nonlinearities of the FCC process mean that the control calculation should be based on a nonlinear model with the relevant constraints included. However, the model can be simple compared to the complexity of the catalytic cracking plant. Model validity is ensured by a robust online model adjustment strategy. Model-predictive control schemes based on linear convolution models have been successfully applied to the supervisory dynamic control of catalytic cracking units, and the control can be further improved by the SSPC scheme.

Modeling and Simulation of the Hydrogenation of α-Methylstyrene on Catalytically Active Metal Foams as Tubular Reactor Packing

Directory of Open Access Journals (Sweden)

Farzad Lali

2016-01-01

Full Text Available This work presents a one-dimensional reactor model for a tubular reactor packed with a catalytically active foam packing with a pore density of 30 PPI in cocurrent upward flow in the example of hydrogenation reaction of α-methylstyrene to cumene. This model includes material, enthalpy, and momentum balances as well as continuity equations. The model was solved within the parameter space applied for experimental studies under assumption of a bubbly flow. The method of orthogonal collocation on finite elements was applied. For isothermal and polytropic processes and steady state conditions, axial profiles for concentration, temperature, fluid velocities, pressure, and liquid holdup were computed and the conversions for various gas and liquid flow rates were validated with experimental results. The obtained results were also compared in terms of space time yield and catalytic activity with experimental results and stirred tank and also with random packed bed reactor. The comparison shows that the application of solid foams as reactor packing is advantageous compared to the monolithic honeycombs and random packed beds.

Experimental investigation of N2O formation in selective non-catalytic NOx reduction processes performed in stoker boiler

Directory of Open Access Journals (Sweden)

Krawczyk Piotr

2016-12-01

Full Text Available Stoker fired boiler plants are common throughout Eastern Europe. Increasingly strict emission standards will require application of secondary NOx abatement systems on such boilers. Yet operation of such systems, in addition to reducing NOx emissions, may also lead to emission of undesirable substances, for example N2O. This paper presents results of experimental tests concerning N2O formation in the selective non-catalytic NOx emission reduction process (SNCR in a stoker boiler (WR 25 type. Obtained results lead to an unambiguous conclusion that there is a dependency between the NOx and N2O concentrations in the exhaust gas when SNCR process is carried out in a coal-fired stoker boiler. Fulfilling new emission standards in the analysed equipment will require 40–50% reduction of NOx concentration. It should be expected that in such a case the N2O emission will be approximately 55–60 mg/m3, with the NOx to N2O conversion factor of about 40%.

Non-canonical spectral decomposition of random functions of the traction voltage and current in electric transportation systems

Directory of Open Access Journals (Sweden)

N.A. Kostin

2015-03-01

Full Text Available The paper proposes the non-canonical spectral decomposition of random functions of the traction voltages and currents. This decomposition is adapted for the electric transportation systems. The numerical representation is carried out for the random function of voltage on the pantograph of electric locomotives VL8 and DE1.

The influence of removable partial dentures on the periodontal health of abutment and non-abutment teeth.

Science.gov (United States)

Dula, Linda J; Shala, Kujtim Sh; Pustina-Krasniqi, Teuta; Bicaj, Teuta; Ahmedi, Enis F

2015-01-01

The aim of this study was to evaluate the influence of removable partial dentures (RPD) on the periodontal health of abutment and non-abutment teeth. A total 107 patients with RPD participated in this study. It was examined 138 RPD, they were 87 with clasp-retained and 51 were RPD with attachments. The following periodontal parameters were evaluated for abutment and non-abutment teeth, plaque index (PLI), calculus index (CI), bleeding on probing (BOP), probing depth (PD) (mm) and tooth mobility (TM) index. These clinical measurements were taken immediately before insertion the RPD, then one and 3 months after insertion. The level of significance was set at (P abutment teeth and non-abutment teeth were no statistically significant at the time of insertion of RPD. After 1-month, PLI was statistically significant (0.57 ± 0.55 for abutment and 0.30 ± 0.46 for non-abutment teeth). After 3 months, there were significant differences between abutment and non-abutment teeth with regard to the BOP (1.53 ± 0.50 and 1.76 ± 0.43 respectively), PD (0.28 ± 0.45 and 0.12 ± 0.33 respectively) and PLI (1.20 ± 0.46 and 0.75 ± 0.64 respectively). No significant mean difference in TM and CI was found between the abutment and non-abutment teeth (P > 0.05). With carefully planned prosthetic treatment and adequate maintenance of the oral and denture hygiene, we can prevent the periodontal diseases.

Study of calcium substitution proportion influence in the catalytic activity at La{sub (1-x)}Ca {sub (x)}MNO{sub 3} (x=0,2 e 0,4) perovskites; Estudo da influencia da proporcao do substituinte calcio na atividade catalitica na rede da perovskita La{sub (1-x)}Ca {sub (x)}MNO{sub 3} (x=0,2 e 0,4)

Energy Technology Data Exchange (ETDEWEB)

Fernandes, M.C.M.; Marques, A.C.; Paiva, A.K.O.; Ruiz, Juan A.C.; Borges, F.M.M., E-mail: marizacmfernandes@hotmail.com [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

2016-07-01

The study of perovskite structured materials has grown due to the interest in producing automotive catalysts with this material. These catalysts aim to convert pollutant gases in gases less harmful the environment. Studies show that the partial substitution of lanthanum atom by a calcium atom improves the material's catalytic activity. In this work two proportions of partial substitution, 20 and 40 mol% were compared. The objective was evaluate the behavior of catalytic activity in methane combustion reactions. The synthesis were made by polymeric precursors method according to Pechini. The material was calcined at 700 and 900 °C for 4h and characterized by Thermogravimetric analysis, X ray diffraction and Scanning electron microscopy. The samples were submitted to Catalytic test in methane combustion reactions. The composition with 20 mol% presented a greater catalytic activity. (author)

Effect of inlet cone pipe angle in catalytic converter

Science.gov (United States)

Amira Zainal, Nurul; Farhain Azmi, Ezzatul; Arifin Samad, Mohd

2018-03-01

The catalytic converter shows significant consequence to improve the performance of the vehicle start from it launched into production. Nowadays, the geometric design of the catalytic converter has become critical to avoid the behavior of backpressure in the exhaust system. The backpressure essentially reduced the performance of vehicles and increased the fuel consumption gradually. Consequently, this study aims to design various models of catalytic converter and optimize the volume of fluid flow inside the catalytic converter by changing the inlet cone pipe angles. Three different geometry angles of the inlet cone pipe of the catalytic converter were assessed. The model is simulated in Solidworks software to determine the optimum geometric design of the catalytic converter. The result showed that by decreasing the divergence angle of inlet cone pipe will upsurge the performance of the catalytic converter.

Non-linear partial differential equations an algebraic view of generalized solutions

CERN Document Server

Rosinger, Elemer E

1990-01-01

A massive transition of interest from solving linear partial differential equations to solving nonlinear ones has taken place during the last two or three decades. The availability of better computers has often made numerical experimentations progress faster than the theoretical understanding of nonlinear partial differential equations. The three most important nonlinear phenomena observed so far both experimentally and numerically, and studied theoretically in connection with such equations have been the solitons, shock waves and turbulence or chaotical processes. In many ways, these phenomen

Life cycle assessment of selective non-catalytic reduction (SNCR) of nitrous oxides in a full-scale municipal solid waste incinerator

DEFF Research Database (Denmark)

Møller, Jacob; Munk, Bjarne; Crillesen, Kim

2011-01-01

Selective non-catalytic reduction (SNCR) of nitrous oxides in a full-scale municipal solid waste incinerator was investigated using LCA. The relationship between NOx-cleaning and ammonia dosage was measured at the plant. Un-reacted ammonia – the ammonia slip – leaving the flue-gas cleaning system......-cleaning efficiency, the fate of the ammonia slip as well as the environmental impact from ammonia production, the potential acidification and nutrient enrichment from NOx-cleaning was calculated as a function of ammonia dosage. Since the exact fate of the ammonia slip could not be measured directly, a number...... of scenarios were set up ranging from “best case” with no ammonia from the slip ending up in the environment to “worst case” where all the ammonia slip eventually ended up in the environment and contributed to environmental pollution. In the “best case” scenario the highest ammonia dosage was most beneficial...

Redox competition mode of scanning electrochemical microscopy (RC-SECM) for visualisation of local catalytic activity.

Science.gov (United States)

Eckhard, Kathrin; Chen, Xingxing; Turcu, Florin; Schuhmann, Wolfgang

2006-12-07

In order to locally analyse catalytic activity on modified surfaces a transient redox competition mode of scanning electrochemical microscopy (SECM) has been developed. In a bi-potentiostatic experiment the SECM tip competes with the sample for the very same analyte. This leads to a current decrease at the SECM tip, if it is positioned in close proximity to an active catalyst site on the surface. Specifically, local catalytic activity of a Pt-catalyst modified sample with respect to the catalytic reduction of molecular oxygen was investigated. At higher local catalytic activity the local 02 partial pressure within the gap between accurately positioned SECM tip and sample is depleted, leading to a noticeable tip current decrease over active sites. A flexible software module has been implemented into the SECM to adapt the competition conditions by proper definition of tip and sample potentials. A potential pulse profile enables the localised electrochemically induced generation of molecular oxygen prior to the competition detection. The current decay curves are recorded over the entire duration of the applied reduction pulse. Hence, a time resolved processing of the acquired current values provides movies of the local oxygen concentration against x,y-position. The SECM redox competition mode was verified with a macroscopic Pt-disk electrode as a test sample to demonstrate the feasibility of the approach. Moreover, highly dispersed electro-deposited spots of gold and platinum on glassy carbon were visualised using the redox competition mode of SECM. Catalyst spots of different nature as well as activity inhomogeneities within one spot caused by local variations in Pt-loading were visualised successfully.

Effects of partial sleep deprivation on slow waves during non-rapid eye movement sleep: A high density EEG investigation.

Science.gov (United States)

Plante, David T; Goldstein, Michael R; Cook, Jesse D; Smith, Richard; Riedner, Brady A; Rumble, Meredith E; Jelenchick, Lauren; Roth, Andrea; Tononi, Giulio; Benca, Ruth M; Peterson, Michael J

2016-02-01

Changes in slow waves during non-rapid eye movement (NREM) sleep in response to acute total sleep deprivation are well-established measures of sleep homeostasis. This investigation utilized high-density electroencephalography (hdEEG) to examine topographic changes in slow waves during repeated partial sleep deprivation. Twenty-four participants underwent a 6-day sleep restriction protocol. Spectral and period-amplitude analyses of sleep hdEEG data were used to examine changes in slow wave energy, count, amplitude, and slope relative to baseline. Changes in slow wave energy were dependent on the quantity of NREM sleep utilized for analysis, with widespread increases during sleep restriction and recovery when comparing data from the first portion of the sleep period, but restricted to recovery sleep if the entire sleep episode was considered. Period-amplitude analysis was less dependent on the quantity of NREM sleep utilized, and demonstrated topographic changes in the count, amplitude, and distribution of slow waves, with frontal increases in slow wave amplitude, numbers of high-amplitude waves, and amplitude/slopes of low amplitude waves resulting from partial sleep deprivation. Topographic changes in slow waves occur across the course of partial sleep restriction and recovery. These results demonstrate a homeostatic response to partial sleep loss in humans. Copyright © 2015 International Federation of Clinical Neurophysiology. Published by Elsevier Ireland Ltd. All rights reserved.

Catalytic burners in larger boiler appliances

Energy Technology Data Exchange (ETDEWEB)

Silversand, Fredrik; Persson, Mikael (Catator AB, Lund (Sweden))

2009-02-15

This project focuses on the scale up of a Catator's catalytic burner technology to enable retrofit installation in existing boilers and the design of new innovative combinations of catalytic burners and boilers. Different design approaches are discussed and evaluated in the report and suggestions are made concerning scale-up. Preliminary test data, extracted from a large boiler installation are discussed together with an accurate analysis of technical possibilities following an optimization of the boiler design to benefit from the advantages of catalytic combustion. The experimental work was conducted in close collaboration with ICI Caldaie (ICI), located in Verona, Italy. ICI is a leading European boiler manufacturer in the effect segment ranging from about 20 kWt to several MWt. The study shows that it is possibly to scale up the burner technology and to maintain low emissions. The boilers used in the study were designed around conventional combustion and were consequently not optimized for implementation of catalytic burners. From previous experiences it stands clear that the furnace volume can be dramatically decreased when applying catalytic combustion. In flame combustion, this volume is normally dimensioned to avoid flame impingement on cold surfaces and to facilitate completion of the gas-phase reactions. The emissions of nitrogen oxides can be reduced by decreasing the residence time in the furnace. Even with the over-dimensioned furnace used in this study, we easily reached emission values close to 35 mg/kWh. The emissions of carbon monoxide and unburned hydrocarbons were negligible (less than 5 ppmv). It is possible to decrease the emissions of nitrogen oxides further by designing the furnace/boiler around the catalytic burner, as suggested in the report. Simultaneously, the size of the boiler installation can be reduced greatly, which also will result in material savings, i.e. the production cost can be reduced. It is suggested to optimize the

Non-random distribution of instability-associated chromosomal rearrangement breakpoints in human lymphoblastoid cells

International Nuclear Information System (INIS)

Moore, Stephen R.; Papworth, David; Grosovsky, Andrew J.

2006-01-01

Genomic instability is observed in tumors and in a large fraction of the progeny surviving irradiation. One of the best-characterized phenotypic manifestations of genomic instability is delayed chromosome aberrations. Our working hypothesis for the current study was that if genomic instability is in part attributable to cis mechanisms, we should observe a non-random distribution of chromosomes or sites involved in instability-associated rearrangements, regardless of radiation quality, dose, or trans factor expression. We report here the karyotypic examination of 296 instability-associated chromosomal rearrangement breaksites (IACRB) from 118 unstable TK6 human B lymphoblast, and isogenic derivative, clones. When we tested whether IACRB were distributed across the chromosomes based on target size, a significant non-random distribution was evident (p < 0.00001), and three IACRB hotspots (chromosomes 11, 12, and 22) and one IACRB coldspot (chromosome 2) were identified. Statistical analysis at the chromosomal band-level identified four IACRB hotspots accounting for 20% of all instability-associated breaks, two of which account for over 14% of all IACRB. Further, analysis of independent clones provided evidence within 14 individual clones of IACRB clustering at the chromosomal band level, suggesting a predisposition for further breaks after an initial break at some chromosomal bands. All of these events, independently, or when taken together, were highly unlikely to have occurred by chance (p < 0.000001). These IACRB band-level cluster hotspots were observed independent of radiation quality, dose, or cellular p53 status. The non-random distribution of instability-associated chromosomal rearrangements described here significantly differs from the distribution that was observed in a first-division post-irradiation metaphase analysis (p = 0.0004). Taken together, these results suggest that genomic instability may be in part driven by chromosomal cis mechanisms

Catalytic wet air oxidation of 2-chlorophenol over sewage sludge-derived carbon-based catalysts

Energy Technology Data Exchange (ETDEWEB)

Tu, Yuting [Institut de recherches sur la catalyse et l’environnement de Lyon (IRCELYON), CNRS – Université Claude Bernard Lyon 1, 2 Avenue Albert Einstein, 69626 Villeurbanne Cedex (France); School of Environmental Science and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China); Xiong, Ya; Tian, Shuanghong [School of Environmental Science and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China); Guangdong Provincial Key Laboratory of Environmental Pollution Control and Remediation Technology, Guangzhou 510275 (China); Kong, Lingjun [School of Environmental Science and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China); Descorme, Claude, E-mail: claude.descorme@ircelyon.univ-lyon1.fr [Institut de recherches sur la catalyse et l’environnement de Lyon (IRCELYON), CNRS – Université Claude Bernard Lyon 1, 2 Avenue Albert Einstein, 69626 Villeurbanne Cedex (France)

2014-07-15

Highlights: • A sewage sludge derived carbon-supported iron oxide catalyst (FeSC) was prepared. • FeSC exhibited high catalytic activity in the wet air oxidation of 2-chlorophenol. • A strong correlation was observed between the 2-CP conversion, the iron leaching and the pH. • Using an acetate buffer, the iron leaching was suppressed while keeping some catalytic activity. • A simplified reaction pathway was proposed for the CWAO of 2-CP over the FeSC catalyst. - Abstract: A sewage sludge derived carbon-supported iron oxide catalyst (FeSC) was prepared and used in the Catalytic Wet Air Oxidation (CWAO) of 2-chlorophenol (2-CP). The catalysts were characterized in terms of elemental composition, surface area, pH{sub PZC}, XRD and SEM. The performances of the FeSC catalyst in the CWAO of 2-CP was assessed in a batch reactor operated at 120 °C under 0.9 MPa oxygen partial pressure. Complete decomposition of 2-CP was achieved within 5 h and 90% Total Organic Carbon (TOC) was removed after 24 h of reaction. Quite a straight correlation was observed between the 2-CP conversion, the amount of iron leached in solution and the pH of the reaction mixture at a given reaction time, indicating a strong predominance of the homogeneous catalysis contribution. The iron leaching could be efficiently prevented when the pH of the solution was maintained at values higher than 4.5, while the catalytic activity was only slightly reduced. Upon four successive batch CWAO experiments, using the same FeSC catalyst recovered by filtration after pH adjustment, only a very minor catalyst deactivation was observed. Finally, based on all the identified intermediates, a simplified reaction pathway was proposed for the CWAO of 2-CP over the FeSC catalyst.

Concentric catalytic combustor

Science.gov (United States)

Bruck, Gerald J [Oviedo, FL; Laster, Walter R [Oviedo, FL

2009-03-24

A catalytic combustor (28) includes a tubular pressure boundary element (90) having a longitudinal flow axis (e.g., 56) separating a first portion (94) of a first fluid flow (e.g., 24) from a second portion (95) of the first fluid flow. The pressure boundary element includes a wall (96) having a plurality of separate longitudinally oriented flow paths (98) annularly disposed within the wall and conducting respective portions (100, 101) of a second fluid flow (e.g., 26) therethrough. A catalytic material (32) is disposed on a surface (e.g., 102, 103) of the pressure boundary element exposed to at least one of the first and second portions of the first fluid flow.

Model correction factor method for reliability problems involving integrals of non-Gaussian random fields

DEFF Research Database (Denmark)

Franchin, P.; Ditlevsen, Ove Dalager; Kiureghian, Armen Der

2002-01-01

The model correction factor method (MCFM) is used in conjunction with the first-order reliability method (FORM) to solve structural reliability problems involving integrals of non-Gaussian random fields. The approach replaces the limit-state function with an idealized one, in which the integrals ...

Effect of support on the catalytic activity of manganese oxide catalyts for toluene combustion.

Science.gov (United States)

Pozan, Gulin Selda

2012-06-30

The aim of this work was to study combustion of toluene (1000ppm) over MnO(2) modified with different supports. α-Al(2)O(3) and γ-Al(2)O(3) obtained from Boehmite, γ-Al(2)O(3) (commercial), SiO(2), TiO(2) and ZrO(2) were used as commercial support materials. In view of potential interest of this process, the influence of support material on the catalytic performance was discussed. The deposition of 9.5MnO(2) was performed by impregnation over support. The catalysts were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), temperature programmed reduction and oxidation (TPR/TPO) and thermogravimetric analysis (TGA). The catalytic tests were carried out at atmospheric pressure in a fixed-bed flow reactor. 9.5MnO(2)/α-Al(2)O(3)(B) (synthesized from Boehmite) catalyst exhibits the highest catalytic activity, over which the toluene conversion was up to 90% at a temperature of 289°C. Considering all the characterization and reaction data reported in this study, it was concluded that the manganese state and oxygen species played an important role in the catalytic activity. Copyright © 2012 Elsevier B.V. All rights reserved.

Influence of 3D effects on 1D aerosol retrievals in synthetic, partially clouded scenes

International Nuclear Information System (INIS)

Stap, F.A.; Hasekamp, O.P.; Emde, C.; Röckmann, T.

2016-01-01

An important challenge in aerosol remote sensing is to retrieve aerosol properties in the vicinity of clouds and in cloud contaminated scenes. Satellite based multi-wavelength, multi-angular, photo-polarimetric instruments are particularly suited for this task as they have the ability to separate scattering by aerosol and cloud particles. Simultaneous aerosol/cloud retrievals using 1D radiative transfer codes cannot account for 3D effects such as shadows, cloud induced enhancements and darkening of cloud edges. In this study we investigate what errors are introduced on the retrieved optical and micro-physical aerosol properties, when these 3D effects are neglected in retrievals where the partial cloud cover is modeled using the Independent Pixel Approximation. To this end a generic, synthetic data set of PARASOL like observations for 3D scenes with partial, liquid water cloud cover is created. It is found that in scenes with random cloud distributions (i.e. broken cloud fields) and either low cloud optical thickness or low cloud fraction, the inversion algorithm can fit the observations and retrieve optical and micro-physical aerosol properties with sufficient accuracy. In scenes with non-random cloud distributions (e.g. at the edge of a cloud field) the inversion algorithm can fit the observations, however, here the retrieved real part of the refractive indices of both modes is biased. - Highlights: • An algorithm for retrieval of both aerosol and cloud properties is presented. • Radiative transfer models of 3D, partially clouded scenes are simulated. • Errors introduced in the retrieved aerosol properties are discussed.

The effectiveness of non-pharmacological interventions in improvement of sleep quality among non-remissive cancer patients: A systematic review of randomized trials

Directory of Open Access Journals (Sweden)

Fatmawati Fadli

2016-12-01

Full Text Available Statistical results estimated that most of non-remissive cancer patients face sleep problem and experience the symptoms of insomnia throughout and after the completion of cancer treatment. The purpose of this review was to compare the effectiveness between several types of non-pharmacological interventions and standard care or treatment to improve the sleep quality among non-remissive cancer patients. All randomized studies focused on non-pharmacological interventions to improve sleep quality among non-remissive cancer patients were included. Thirteen studies were selected with a total of 1,617 participants. The results found that only four interventions were significantly effective to improve sleep quality among non-remissive cancer patients, included cognitive behavioral therapy, relaxation and guided imagery program, self-care behavior education program, and energy and sleep enhancement program.

Preliminary X-ray crystallographic studies of BthTX-II, a myotoxic Asp49-phospholipase A2 with low catalytic activity from Bothrops jararacussu venom

International Nuclear Information System (INIS)

Corrêa, L. C.; Marchi-Salvador, D. P.; Cintra, A. C. O.; Soares, A. M.; Fontes, M. R. M.

2006-01-01

A myotoxic Asp49-PLA 2 with low catalytic activity from B. jararacussu (BthTX-II) was crystallized in the monoclinic crystal system; a complete X-ray diffraction data set was collected and a molecular-replacement solution was obtained. The oligomeric structure of BthTX-II resembles those of the Asp49-PLA 2 PrTX-III and all bothropic Lys49-PLA 2 s. For the first time, a complete X-ray diffraction data set has been collected from a myotoxic Asp49-phospholipase A 2 (Asp49-PLA 2 ) with low catalytic activity (BthTX-II from Bothrops jararacussu venom) and a molecular-replacement solution has been obtained with a dimer in the asymmetric unit. The quaternary structure of BthTX-II resembles the myotoxin Asp49-PLA 2 PrTX-III (piratoxin III from B. pirajai venom) and all non-catalytic and myotoxic dimeric Lys49-PLA 2 s. In contrast, the oligomeric structure of BthTX-II is different from the highly catalytic and non-myotoxic BthA-I (acidic PLA 2 from B. jararacussu). Thus, comparison between these structures should add insight into the catalytic and myotoxic activities of bothropic PLA 2 s

Catalytic models developed through social work

DEFF Research Database (Denmark)

Jensen, Mogens

2015-01-01

of adolescents placed in out-of-home care and is characterised using three situated cases as empirical data. Afterwards the concept of catalytic processes is briefly presented and then applied in an analysis of pedagogical treatment in the three cases. The result is a different conceptualisation of the social......The article develops the concept of catalytic processes in relation to social work with adolescents in an attempt to both reach a more nuanced understanding of social work and at the same time to develop the concept of catalytic processes in psychology. The social work is pedagogical treatment...

On the removal of boundary errors caused by Runge-Kutta integration of non-linear partial differential equations

Science.gov (United States)

Abarbanel, Saul; Gottlieb, David; Carpenter, Mark H.

1994-01-01

It has been previously shown that the temporal integration of hyperbolic partial differential equations (PDE's) may, because of boundary conditions, lead to deterioration of accuracy of the solution. A procedure for removal of this error in the linear case has been established previously. In the present paper we consider hyperbolic (PDE's) (linear and non-linear) whose boundary treatment is done via the SAT-procedure. A methodology is present for recovery of the full order of accuracy, and has been applied to the case of a 4th order explicit finite difference scheme.

Catalytically favorable surface patterns in Pt-Au nanoclusters

KAUST Repository

Mokkath, Junais Habeeb

2013-01-01

Motivated by recent experimental demonstrations of novel PtAu nanoparticles with highly enhanced catalytic properties, we present a systematic theoretical study that explores principal catalytic indicators as a function of the particle size and composition. We find that Pt electronic states in the vicinity of the Fermi level combined with a modified electron distribution in the nanoparticle due to Pt-to-Au charge transfer are the origin of the outstanding catalytic properties. From our model we deduce the catalytically favorable surface patterns that induce ensemble and ligand effects. © The Royal Society of Chemistry 2013.

Turning goals into results: the power of catalytic mechanisms.

Science.gov (United States)

Collins, J

1999-01-01

Most executives have a big, hairy, audacious goal. They write vision statements, formalize procedures, and develop complicated incentive programs--all in pursuit of that goal. In other words, with the best of intentions, they install layers of stultifying bureaucracy. But it doesn't have to be that way. In this article, Jim Collins introduces the catalytic mechanism, a simple yet powerful managerial tool that helps translate lofty aspirations into concrete reality. Catalytic mechanisms are the crucial link between objectives and performance; they are a galvanizing, nonbureaucratic means to turn one into the other. What's the difference between catalytic mechanisms and most traditional managerial controls? Catalytic mechanisms share five characteristics. First, they produce desired results in unpredictable ways. Second, they distribute power for the benefit of the overall system, often to the discomfort of those who traditionally hold power. Third, catalytic mechanisms have teeth. Fourth, they eject "viruses"--those people who don't share the company's core values. Finally, they produce an ongoing effect. Catalytic mechanisms are just as effective for reaching individual goals as they are for corporate ones. To illustrate how catalytic mechanisms work, the author draws on examples of individuals and organizations that have relied on such mechanisms to achieve their goals. The same catalytic mechanism that works in one organization, however, will not necessarily work in another. Catalytic mechanisms must be tailored to specific goals and situations. To help readers get started, the author offers some general principles that support the process of building catalytic mechanisms effectively.

Atomically Precise Metal Nanoclusters for Catalytic Application

Energy Technology Data Exchange (ETDEWEB)

Jin, Rongchao [Carnegie Mellon Univ., Pittsburgh, PA (United States)

2016-11-18

The central goal of this project is to explore the catalytic application of atomically precise gold nanoclusters. By solving the total structures of ligand-protected nanoclusters, we aim to correlate the catalytic properties of metal nanoclusters with their atomic/electronic structures. Such correlation unravel some fundamental aspects of nanocatalysis, such as the nature of particle size effect, origin of catalytic selectivity, particle-support interactions, the identification of catalytically active centers, etc. The well-defined nanocluster catalysts mediate the knowledge gap between single crystal model catalysts and real-world conventional nanocatalysts. These nanoclusters also hold great promise in catalyzing certain types of reactions with extraordinarily high selectivity. These aims are in line with the overall goals of the catalytic science and technology of DOE and advance the BES mission “to support fundamental research to understand, predict, and ultimately control matter and energy at the level of electrons, atoms, and molecules”. Our group has successfully prepared different sized, robust gold nanoclusters protected by thiolates, such as Au₂₅(SR)₁₈, Au₂₈(SR)₂₀, Au₃₈(SR)₂₄, Au₉₉(SR)₄₂, Au₁₄₄(SR)₆₀, etc. Some of these nanoclusters have been crystallographically characterized through X-ray crystallography. These ultrasmall nanoclusters (< 2 nm diameter) exhibit discrete electronic structures due to quantum size effect, as opposed to quasicontinuous band structure of conventional metal nanoparticles or bulk metals. The available atomic structures (metal core plus surface ligands) of nanoclusters serve as the basis for structure-property correlations. We have investigated the unique catalytic properties of nanoclusters (i.e. not observed in conventional nanogold catalysts) and revealed the structure-selectivity relationships. Highlights of our

Design of adiabatic fixed-bed reactors for the partial oxidation of methane to synthesis gas. Application to production of methanol and hydrogen-for-fuel-cells

NARCIS (Netherlands)

Smet, de C.R.H.; Croon, de M.H.J.M.; Berger, R.J.; Marin, G.B.M.M.; Schouten, J.C.

2001-01-01

Adiabatic fixed-bed reactors for the catalytic partial oxidn. (CPO) of methane to synthesis gas were designed at conditions suitable for the prodn. of methanol and hydrogen-for-fuel-cells. A steady-state, one-dimensional heterogeneous reactor model was applied in the simulations. Intra-particle

Ni-doped (CeO2−δ)–YSZ mesoarchitectured with nanocrystalline framework: the effect of thermal treatment on structure, surface chemistry and catalytic properties in the partial oxidation of methane (CPOM)

International Nuclear Information System (INIS)

Somacescu, Simona; Florea, Mihaela; Osiceanu, Petre; Calderon-Moreno, Jose Maria; Ghica, Corneliu; Serra, Jose Manuel

2015-01-01

Ni-doped (CeO 2−δ )–YSZ (5 mol% Ni oxide, 10 mol% ceria) mesoarchitectures (MA) with nanocrystalline framework have been synthesized by an original, facile and cheap approach based on Triton X100 nonionic surfactant as template and water as solvent at a strong basic pH value. Following the hydrothermal treatment under autogenous pressure (∼18 bars), Ni, Ce, Y, and Zr were well ordered as MA with nanocrystalline framework, assuring thermal stability. A comprehensive investigation of structure, texture, morphology, and surface chemistry was performed by means of a variety of complementary techniques (X-Ray Diffraction, XRD; Raman Spectroscopy, RS; Brunauer—Emmett—Teller, BET; Temperature—Programmed Reduction, TPR; Transmission Electron Microscopy, TEM and DF-STEM; X-ray Photoelectron Spectroscopy, XPS; Catalytic activity and selectivity). N 2 sorption measurements highlighted that the mesoporous structure is formed at 600 °C and remains stable at 800 °C. At 900 °C, the MA collapses, favoring the formation of macropores. The XRD and Raman Spectroscopy of all samples showed the presence of a pure, single phase with fluorite-type structure. At 900 °C, an increased tetragonal distortion of the cubic lattice was observed. The surface chemistry probed by XPS exhibits a mixture of oxidation states (Ce 3+  + Ce 4+ ) with high percentage of Ce 3+ valence state ∼35 % and (Ni 3+ and Ni 2+ ) oxidation states induced by the thermal treatment. These nanoparticles assembled into MA show high stability and selectivity over time in catalytic partial oxidation of methane (CPOM). These promising performances suggest an interesting prospect for introduction as anode within IT-SOFC assemblies.Graphical Abstract

Immediate occluding definitive partial fixed prosthesis versus non-occluding provisional restorations - 4-month post-loading results from a pragmatic multicenter randomised controlled trial.

Science.gov (United States)

Heinemann, Friedhelm; Grufferty, Brendan; Papavasiliou, George; Dominiak, Marzena; García, Jaime Jiménez; Trullenque-Eriksson, Anna; Esposito, Marco

2016-01-01

To compare the clinical outcome of dental implants restored with definitive occluding partial fixed prostheses within 1 week, after implant placement with immediate non-occluding provisional restorations, which were to be replaced by definitive prostheses after 4 months. Fifty partially edentulous patients treated with one to three dental implants, at least 8.5 mm long and 4.0 mm wide inserted with a torque of at least 35 Ncm, were randomised in two groups of 25 patients each, to be immediately loaded with partial fixed prostheses. Patients of one group received one definitive screw-retained metal-ceramic prosthesis in occlusion within 1 week after placement. Patients of the other group received one non-occluding provisional acrylic reinforced prosthesis within 24 h after implant placement. Provisional prostheses were replaced after 4 months by definitive ones. The follow-up for all patients was 4-months post-loading. Outcome measures were prosthesis and implant failures, any complications, peri-implant marginal bone level changes, aesthetic evaluation by a clinician, patient satisfaction, chair time and number of visits at the dental office from implant placement to delivery of definitive restorations. No patient dropped out. Two immediately occlusally loaded implants with their related definitive prostheses (8%) failed early (difference in proportions = 0.08; 95% CI: -0.03 to 0.19; P = 0.490). Four complications occurred in the occlusal group versus one in the non-occlusal group; (difference in proportions = 0.12; 95% CI: -0.04 to 0.28; P = 0.349). Four months after loading, patients subjected to non-occlusal loading lost an average of 0.72 mm of peri-implant bone versus 0.99 mm of patients restored with occluding definitive partial fixed prostheses. There were no statistically significant differences for marginal bone level changes between the two groups (mean difference = -0.27 mm; 95% CI: -0.84 to 0.30; P = 0.349). The differences for aesthetic scores showed

Clinical application of removable partial dentures using thermoplastic resin-part I: definition and indication of non-metal clasp dentures.

Science.gov (United States)

Fueki, Kenji; Ohkubo, Chikahiro; Yatabe, Masaru; Arakawa, Ichiro; Arita, Masahiro; Ino, Satoshi; Kanamori, Toshikazu; Kawai, Yasuhiko; Kawara, Misao; Komiyama, Osamu; Suzuki, Tetsuya; Nagata, Kazuhiro; Hosoki, Maki; Masumi, Shin-Ichi; Yamauchi, Mutsuo; Aita, Hideki; Ono, Takahiro; Kondo, Hisatomo; Tamaki, Katsushi; Matsuka, Yoshizo; Tsukasaki, Hiroaki; Fujisawa, Masanori; Baba, Kazuyoshi; Koyano, Kiyoshi; Yatani, Hirofumi

2014-01-01

This position paper proposes a definition and naming standard for removable partial dentures (RPDs) using thermoplastic resin, and presents a guideline for clinical application. A panel of 14 experts having broad experience with clinical application of RPDs using thermoplastic resin was selected from members of the Japan Prosthodontic Society. At a meeting of the panel, "non-metal clasp denture" was referred as the generic name of RPDs with retentive elements (resin clasps) made of thermoplastic resin. The panel classified non-metal clasp dentures into two types: one with a flexible structure that lacks a metal framework and the other having a rigid structure that includes a metal framework. According to current prosthetic principles, flexible non-metal clasp dentures are not recommended as definitive dentures, except for limited cases such as patients with a metal allergy. Rigid non-metal clasp dentures are recommended in cases where patients will not accept metal clasps for esthetic reasons. Non-metal clasp dentures should follow the same design principles as conventional RPDs using metal clasps. Copyright © 2013 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Nitrogen removal from wastewater by a catalytic oxidation method.

Science.gov (United States)

Huang, T L; Macinnes, J M; Cliffe, K R

2001-06-01

The ammonia-containing waste produced in industries is usually characterized by high concentration and high temperature, and is not treatable by biological methods directly. In this study, a hydrophobic Pt/SDB catalyst was first used in a trickle-bed reactor to remove ammonia from wastewater. In the reactor, both stripping and catalytic oxidation occur simultaneously. It was found that higher temperature and higher oxygen partial pressure enhanced the ammonia removal. A reaction pathway, which involves oxidizing ammonia to nitric oxide, which then further reacts with ammonia to produce nitrogen and water, was confirmed. Small amounts of by-products, nitrites and nitrates were also detected in the resultant reaction solution. These compounds came from the absorption of nitrogen oxides. Both the minimum NO2- selectivity and maximum ammonia removal were achieved when the resultant pH of treated water was near 7.5 for a feed of unbuffered ammonia solution.

Randomized phase III trial of regorafenib in metastatic colorectal cancer: analysis of the CORRECT Japanese and non-Japanese subpopulations.

Science.gov (United States)

Yoshino, Takayuki; Komatsu, Yoshito; Yamada, Yasuhide; Yamazaki, Kentaro; Tsuji, Akihito; Ura, Takashi; Grothey, Axel; Van Cutsem, Eric; Wagner, Andrea; Cihon, Frank; Hamada, Yoko; Ohtsu, Atsushi

2015-06-01

In the international, phase III, randomized, double-blind CORRECT trial, regorafenib significantly prolonged overall survival (OS) versus placebo in patients with metastatic colorectal cancer (mCRC) that had progressed on all standard therapies. This post hoc analysis evaluated the efficacy and safety of regorafenib in Japanese and non-Japanese subpopulations in the CORRECT trial. Patients were randomized 2 : 1 to regorafenib 160 mg once daily or placebo for weeks 1-3 of each 4-week cycle. The primary endpoint was OS. Outcomes were assessed using descriptive statistics. One hundred Japanese and 660 non-Japanese patients were randomized to regorafenib (n = 67 and n = 438) or placebo (n = 33 and n = 222). Regorafenib had a consistent OS benefit in the Japanese and non-Japanese subpopulations, with hazard ratios of 0.81 (95 % confidence interval [CI] 0.43-1.51) and 0.77 (95 % CI 0.62-0.94), respectively. Regorafenib-associated hand-foot skin reaction, hypertension, proteinuria, thrombocytopenia, and lipase elevations occurred more frequently in the Japanese subpopulation than in the non-Japanese subpopulation, but were generally manageable. Regorafenib appears to have comparable efficacy in Japanese and non-Japanese subpopulations, with a manageable adverse-event profile, suggesting that this agent could potentially become a standard of care in patients with mCRC.

Catalytic Stereoinversion of L-Alanine to Deuterated D-Alanine.

Science.gov (United States)

Moozeh, Kimia; So, Soon Mog; Chin, Jik

2015-08-03

A combination of an achiral pyridoxal analogue and a chiral base has been developed for catalytic deuteration of L-alanine with inversion of stereochemistry to give deuterated D-alanine under mild conditions (neutral pD and 25 °C) without the use of any protecting groups. This system can also be used for catalytic deuteration of D-alanine with retention of stereochemistry to give deuterated D-alanine. Thus a racemic mixture of alanine can be catalytically deuterated to give an enantiomeric excess of deuterated D-alanine. While catalytic deracemization of alanine is forbidden by the second law of thermodynamics, this system can be used for catalytic deracemization of alanine with deuteration. Such green and biomimetic approach to catalytic stereocontrol provides insights into efficient amino acid transformations. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Review on Catalytic Membranes Production and Applications

Directory of Open Access Journals (Sweden)

Heba Abdallah

2017-05-01

Full Text Available The development of the chemical industry regarding reducing the production cost and obtaining a high-quality product with low environmental impact became the essential requirements of the world in these days. The catalytic membrane is considered as one of the new alternative solutions of catalysts problems in the industries, where the reaction and separation can be amalgamated in one unit. The catalytic membrane has numerous advantages such as breaking the thermodynamic equilibrium limitation, increasing conversion rate, reducing the recycle and separation costs. But the limitation or most disadvantages of catalytic membranes related to the high capital costs for fabrication or the fact that manufacturing process is still under development. This review article summarizes the most recent advances and research activities related to preparation, characterization, and applications of catalytic membranes. In this article, various types of catalytic membranes are displayed with different applications and explained the positive impacts of using catalytic membranes in various reactions. Copyright © 2017 BCREC Group. All rights reserved. Received: 1st April 2016; Revised: 14th February 2017; Accepted: 22nd February 2017 How to Cite: Abdallah, H. (2017. A Review on Catalytic Membranes Production and Applications. Bulletin of Chemical Reaction Engineering & Catalysis, 12 (2: 136-156 (doi:10.9767/bcrec.12.2.462.136-156 Permalink/DOI: http://dx.doi.org/10.9767/bcrec.12.2.462.136-156

Accelerated re-epithelialization of partial-thickness skin wounds by a topical betulin gel: Results of a randomized phase III clinical trials program.

Science.gov (United States)

Barret, Juan P; Podmelle, Fred; Lipový, Břetislav; Rennekampff, Hans-Oliver; Schumann, Hauke; Schwieger-Briel, Agnes; Zahn, Tobias R; Metelmann, Hans-Robert

2017-09-01

The clinical significance of timely re-epithelialization is obvious in burn care, since delayed wound closure is enhancing the risk of wound site infection and extensive scarring. Topical treatments that accelerate wound healing are urgently needed to reduce these sequelae. Evidence from preliminary studies suggests that betulin can accelerate the healing of different types of wounds, including second degree burns and split-thickness skin graft wounds. The goal of this combined study program consisting of two randomized phase III clinical trials in parallel is to evaluate whether a topical betulin gel (TBG) is accelerating re-epithelialization of split-thickness skin graft (STSG) donor site wounds compared to standard of care. Two parallel blindly evaluated, randomised, controlled, multicentre phase III clinical trials were performed in adults undergoing STSG surgery (EudraCT nos. 2012-003390-26 and 2012-000777-23). Donor site wounds were split into two equal halves and randomized 1:1 to standard of care (a non-adhesive moist wound dressing) or standard of care plus TBG consisting of 10% birch bark extract and 90% sunflower oil (Episalvan, Birken AG, Niefern-Oeschelbronn, Germany). The primary efficacy assessment was the intra-individual difference in time to wound closure assessed from digital photographs by three blinded experts. A total of 219 patients were included and treated in the two trials. Wounds closed faster with TBG than without it (15.3 vs. 16.5 days; mean intra-individual difference=-1.1 days [95% CI, -1.5 to -0.7]; p<0.0001). This agreed with unblinded direct clinical assessment (difference=-2.1 days [95% CI, -2.7 to -1.5]; p<0.0001). Adverse events possibly related to treatment were mild or moderate and mostly at the application site. TBG accelerates re-epithelialization of partial thickness wounds compared to the current standard of care, providing a well-tolerated contribution to burn care in practice. Copyright © 2017 The Authors. Published by

DNA hydrogel as a template for synthesis of ultrasmall gold nanoparticles for catalytic applications.

Science.gov (United States)

Zinchenko, Anatoly; Miwa, Yasuyuki; Lopatina, Larisa I; Sergeyev, Vladimir G; Murata, Shizuaki

2014-03-12

DNA cross-linked hydrogel was used as a matrix for synthesis of gold nanoparticles. DNA possesses a strong affinity to transition metals such as gold, which allows for the concentration of Au precursor inside a hydrogel. Further reduction of HAuCl4 inside DNA hydrogel yields well dispersed, non-aggregated spherical Au nanoparticles of 2-3 nm size. The average size of these Au nanoparticles synthesized in DNA hydrogel is the smallest reported so far for in-gel metal nanoparticles synthesis. DNA hybrid hydrogel containing gold nanoparticles showed high catalytic activity in the hydrogenation reaction of nitrophenol to aminophenol. The proposed soft hybrid material is promising as environmentally friendly and sustainable material for catalytic applications.

Axial Changes of Catalyst Structure and Temperature in a Fixed-Bed Microreactor During Noble Metal Catalysed Partial Oxidation of Methane

DEFF Research Database (Denmark)

Hannemann, S.; Grunwaldt, Jan-Dierk; Kimmerle, B.

2009-01-01

The catalytic partial oxidation of methane (CPO) over flame-made 2.5%Rh-2.5%Pt/Al2O3 and 2.5%Rh/Al2O3 in 6%CH4/3%O-2/He shows the potential of in situ studies using miniaturized fixed-bed reactors, the importance of spatially resolved studies and its combination with infrared thermography and on-...

Microbiological and clinical assessment of the abutment and non-abutment teeth of partial removable denture wearers.

Science.gov (United States)

Costa, Luciana; do Nascimento, Cássio; de Souza, Valéria Oliveira Pagnano; Pedrazzi, Vinícius

2017-03-01

The aim of this study was assessing the changes in both clinical and microbiological parameters of healthy individuals after rehabilitation with removable partial denture (RPD). 11 women received unilateral or bilateral free-end saddle RPD in the mandibular arch. Clinical and microbiological parameters of abutment, non-abutment, and antagonist teeth were assessed at baseline (RPD installation) and after 7, 30, 90, and 180days of function. The Checkerboard DNA-DNA hybridization technique was used to identify and quantify up to 43 different microbial species from subgingival biofilm samples. Probing depth, gingival recession, and bleeding on probing were also investigated over time. The total and individual microbial genome counts were shown significantly increased after 180days with no significant differences between abutment, non-abutment, or antagonist teeth. Streptococcus spp., Aggregatibacter actinomycetemcomitans, and other species associated to periodontitis (Peptostreptococcus anaerobius, Prevotella nigrescens, and Tannerella forsythia), as well as opportunistic Candida spp., were recovered in moderate counts. Abutment teeth presented higher values of gingival recession when compared with non-abutment or antagonist teeth, irrespectively time of sampling (pabutment and non-abutment teeth with no significant differences regarding the microbial profile over time. Bleeding on probing and probing depth showed no significant difference between groups over time whereas gingival recession increased in the abutment teeth. Copyright © 2016 Elsevier Ltd. All rights reserved.

Control method for multi-input multi-output non-Gaussian random vibration test with cross spectra consideration

Directory of Open Access Journals (Sweden)

Ronghui ZHENG

2017-12-01

Full Text Available A control method for Multi-Input Multi-Output (MIMO non-Gaussian random vibration test with cross spectra consideration is proposed in the paper. The aim of the proposed control method is to replicate the specified references composed of auto spectral densities, cross spectral densities and kurtoses on the test article in the laboratory. It is found that the cross spectral densities will bring intractable coupling problems and induce difficulty for the control of the multi-output kurtoses. Hence, a sequential phase modification method is put forward to solve the coupling problems in multi-input multi-output non-Gaussian random vibration test. To achieve the specified responses, an improved zero memory nonlinear transformation is utilized first to modify the Fourier phases of the signals with sequential phase modification method to obtain one frame reference response signals which satisfy the reference spectra and reference kurtoses. Then, an inverse system method is used in frequency domain to obtain the continuous stationary drive signals. At the same time, the matrix power control algorithm is utilized to control the spectra and kurtoses of the response signals further. At the end of the paper, a simulation example with a cantilever beam and a vibration shaker test are implemented and the results support the proposed method very well. Keywords: Cross spectra, Kurtosis control, Multi-input multi-output, Non-Gaussian, Random vibration test

SUSY/non-SUSY duality in U(N gauge model with partially broken N=2 supersymmetry

Directory of Open Access Journals (Sweden)

Kazunobu Maruyoshi

2009-03-01

Full Text Available We study the vacuum structure of the U(N gauge model with partially broken N=2 supersymmetry. From the analysis of the classical vacua of this model, we point out that in addition to the ordinary N=1 supersymmetric vacua, there are vacua with negative gauge coupling constants, which preserve another N=1 supersymmetry. These latter vacua can be analyzed by using SUSY/non-SUSY duality which is recently proposed by Aganagic, Beem, Seo and Vafa. A dual description of these in UV is U(N gauge theory where the supersymmetry is broken by spurion superfields. Following them, we see that there are supersymmetry preserving vacua as well as supersymmetry breaking vacua of low energy effective theory.

Remote Exosites of the Catalytic Domain of Matrix Metalloproteinase-12 Enhance Elastin Degradation┼

Science.gov (United States)

Fulcher, Yan G.; Van Doren, Steven R.

2011-01-01

How does matrix metalloproteinase-12 (MMP-12 or metalloelastase) degrade elastin with high specific activity? NMR suggested soluble elastin to cover surfaces of MMP-12 far from its active site. Two of these surfaces have been found, by mutagenesis guided by the BINDSIght approach, to affect degradation and affinity for elastin substrates but not a small peptide substrate. Main exosite 1 has been extended out to Asp124 that binds calcium. Novel exosite 2 comprises residues from the II–III loop and β-strand I near the back of the catalytic domain. The high exposure of these distal exosites may make them accessible to elastin made more flexible by partial hydrolysis. Importantly, combination of a lesion at each of exosites 1 and 2 and active site decreased catalytic competence towards soluble elastin by 13- to 18-fold to the level of MMP-3, homologue and poor elastase. Double mutant cycle analysis of conservative mutations of Met156 (exosite 2) and either Asp124 (exosite 1) or Ile180 (active site) had additive effects. Compared to polar substitutions observed in other MMPs, Met156 enhanced affinity and Ile180 kcat for soluble elastin. Both residues detracted from the higher folding stability with polar mutations. This resembles the trend in enzymes of an inverse relationship between folding stability and activity. Restoring Asp124 from combination mutants enhanced kcat for soluble elastin. In elastin degradation, exosites 1 and 2 contributed independently of each other and Ile180 at the active site, but with partial coupling to Ala182 near the active site. The concept of weak, separated interactions coalescing somewhat independently can be extended to this proteolytic digestion of a protein from fibrils. PMID:21967233

E-learning in pediatric basic life support: a randomized controlled non-inferiority study.

Science.gov (United States)

Krogh, Lise Qvirin; Bjørnshave, Katrine; Vestergaard, Lone Due; Sharma, Maja Bendtsen; Rasmussen, Stinne Eika; Nielsen, Henrik Vendelbo; Thim, Troels; Løfgren, Bo

2015-05-01

Dissemination of pediatric basic life support (PBLS) skills is recommended. E-learning is accessible and cost-effective, but it is currently unknown whether laypersons can learn PBLS through e-learning. The hypothesis of this study was to investigate whether e-learning PBLS is non-inferior to instructor-led training. Participants were recruited among child-minders and parents of children aged 0-6 years. Participants were randomized to either 2-h instructor-led training or e-learning using an e-learning program (duration 17 min) including an inflatable manikin. After training, participants were assessed in a simulated pediatric cardiac arrest scenario. Tests were video recorded and PBLS skills were assessed independently by two assessors blinded to training method. Primary outcome was the pass rate of the PBLS test (≥8 of 15 skills adequately performed) with a pre-specified non-inferiority margin of 20%. In total 160 participants were randomized 1:1. E-learning was non-inferior to instructor-led training (difference in pass rate -4%; 95% CI -9:0.5). Pass rates were 100% among instructor-led trained (n=67) and 96% among e-learned (n=71). E-learners median time spent on the e-learning program was 30 min (range: 15-120 min) and the median number of log-ons was 2 (range: 1-5). After the study, all participants felt that their skills had improved. E-learning PBLS is non-inferior to instructor-led training among child-minders and parents with children aged 0-6 years, although the pass rate was 4% (95% CI -9:0.5) lower with e-learning. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

A thermogravimetric analysis (TGA) method to determine the catalytic conversion of cellulose from carbon-supported hydrogenolysis process

International Nuclear Information System (INIS)

Leal, Glauco F.; Ramos, Luiz A.; Barrett, Dean H.; Curvelo, Antonio Aprígio S.; Rodella, Cristiane B.

2015-01-01

Graphical abstract: - Highlights: • A new method to determine the catalytic conversion of cellulose using TGA has been developed. • TGA is able to differentiate between carbon from cellulose and carbon from the catalyst. • Building an analytical curve from TGA results enables the accurate determination of cellulose conversion. - Abstract: The ability to determine the quantity of solid reactant that has been transformed after a catalytic reaction is fundamental in accurately defining the conversion of the catalyst. This quantity is also central when investigating the recyclability of a solid catalyst as well as process control in an industrial catalytic application. However, when using carbon-supported catalysts for the conversion of cellulose this value is difficult to obtain using only a gravimetric method. The difficulty lies in weighing errors caused by loss of the solid mixture (catalyst and non-converted cellulose) after the reaction and/or moisture adsorption by the substrate. These errors are then propagated into the conversion calculation giving erroneous results. Thus, a quantitative method using thermogravimetric analysis (TGA) has been developed to determine the quantity of cellulose after a catalytic reaction by using a tungsten carbide catalyst supported on activated carbon. Stepped separation of TGA curves was used for quantitative analysis where three thermal events were identified: moisture loss, cellulose decomposition and CO/CO 2 formation. An analytical curve was derived and applied to quantify the residual cellulose after catalytic reactions which were performed at various temperatures and reaction times. The catalytic conversion was calculated and compared to the standard gravimetric method. Results showed that catalytic cellulose conversion can be determined using TGA and exhibits lower uncertainty (±2%) when compared to gravimetric determination (±5%). Therefore, it is a simple and relatively inexpensive method to determine catalytic

On evolving deformation microstructures in non-convex partially damaged solids

KAUST Repository

Gurses, Ercan; Miehe, Christian

2011-01-01

. These microstructures can be resolved by use of relaxation techniques associated with the construction of convex hulls. We propose a particular relaxation method for partially damaged solids and investigate it in one- and multi-dimensional settings. To this end, we

On the Structural Context and Identification of Enzyme Catalytic Residues

Directory of Open Access Journals (Sweden)

Yu-Tung Chien

2013-01-01

Full Text Available Enzymes play important roles in most of the biological processes. Although only a small fraction of residues are directly involved in catalytic reactions, these catalytic residues are the most crucial parts in enzymes. The study of the fundamental and unique features of catalytic residues benefits the understanding of enzyme functions and catalytic mechanisms. In this work, we analyze the structural context of catalytic residues based on theoretical and experimental structure flexibility. The results show that catalytic residues have distinct structural features and context. Their neighboring residues, whether sequence or structure neighbors within specific range, are usually structurally more rigid than those of noncatalytic residues. The structural context feature is combined with support vector machine to identify catalytic residues from enzyme structure. The prediction results are better or comparable to those of recent structure-based prediction methods.

Removal of ammonia solutions used in catalytic wet oxidation processes.

Science.gov (United States)

Hung, Chang Mao; Lou, Jie Chung; Lin, Chia Hua

2003-08-01

Ammonia (NH(3)) is an important product used in the chemical industry, and is common place in industrial wastewater. Industrial wastewater containing ammonia is generally either toxic or has concentrations or temperatures such that direct biological treatment is unfeasible. This investigation used aqueous solutions containing more of ammonia for catalytic liquid-phase oxidation in a trickle-bed reactor (TBR) based on Cu/La/Ce composite catalysts, prepared by co-precipitation of Cu(NO(3))(2), La(NO(3))(2), and Ce(NO(3))(3) at 7:2:1 molar concentrations. The experimental results indicated that the ammonia conversion of the wet oxidation in the presence of the Cu/La/Ce composite catalysts was determined by the Cu/La/Ce catalyst. Minimal ammonia was removed from the solution by the wet oxidation in the absence of any catalyst, while approximately 91% ammonia removal was achieved by wet oxidation over the Cu/La/Ce catalyst at 230 degrees C with oxygen partial pressure of 2.0 MPa. Furthermore, the effluent streams were conducted at a liquid hourly space velocity of under 9 h(-1) in the wet catalytic processes, and a reaction pathway was found linking the oxidizing ammonia to nitric oxide, nitrogen and water. The solution contained by-products, including nitrates and nitrites. Nitrite selectivity was minimized and ammonia removal maximized when the feed ammonia solution had a pH of around 12.0.

Operating characteristics of a partial-block randomized crossover bioequivalence study for dutasteride, a drug with a long half-life: investigation through simulation and comparison with final results.

Science.gov (United States)

Cai, Gengqian; Thiessen, Jake J; Baidoo, Charlotte A; Fossler, Michael J

2010-10-01

Studies to establish bioequivalence (BE) of a drug are important elements in support of drug applications. A typical BE study is conducted as a single dose, randomized, 2-period crossover design. For drugs with long half lives (≥ 48 hours) and evaluation of multiple BE objectives in 1 trial, this design may not be adequate. A parallel design may then be a more appropriate choice. However, parallel designs require increased sample size, which can become substantial. One option that is a compromise between the complete randomized block design and the parallel design is a partial-block crossover design. This approach came about during the development of a combination of dutasteride and tamsulosin. Previous experience with performing single-dose dutasteride studies suggested that 28 days of washout is needed between treatments because of its half-life of 7-9 days. Simulations were performed to assess the operating characteristics of this design using a previously developed PK model. Four scenarios were developed, and each scenario was simulated 500 times. The results showed that this design demonstrated acceptable consumer and producer risk. Partial-block crossover designs should be considered for studies when the half-life of the drug is long and there are more than 2 periods.

How edge-reinforced random walk arises naturally

NARCIS (Netherlands)

Rolles, S.W.W.

2003-01-01

We give a characterization of a modified edge-reinforced random walk in terms of certain partially exchangeable sequences. In particular, we obtain a characterization of an edge-reinforced random walk (introduced by Coppersmith and Diaconis) on a 2-edge-connected graph. Modifying the notion of

Catalytic activity of Au nanoparticles

DEFF Research Database (Denmark)

Larsen, Britt Hvolbæk; Janssens, Ton V.W.; Clausen, Bjerne

2007-01-01

Au is usually viewed as an inert metal, but surprisingly it has been found that Au nanoparticles less than 3–5 nm in diameter are catalytically active for several chemical reactions. We discuss the origin of this effect, focusing on the way in which the chemical activity of Au may change with par......Au is usually viewed as an inert metal, but surprisingly it has been found that Au nanoparticles less than 3–5 nm in diameter are catalytically active for several chemical reactions. We discuss the origin of this effect, focusing on the way in which the chemical activity of Au may change...... with particle size. We find that the fraction of low-coordinated Au atoms scales approximately with the catalytic activity, suggesting that atoms on the corners and edges of Au nanoparticles are the active sites. This effect is explained using density functional calculations....

Highly active and non-corrosive catalytic systems for the coupling reactions of ethylene oxide and CO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Zhang, Shuyao; Jin, So Jeong; Kim, Young Jin; Lee, Je Seung; Kim, Hoon Sik [Dept. of Chemistry and Research Institute of Basic Sciences, Kyung Hee University, Seoul (Korea, Republic of); Hong, Jongki; Lee, Won Woong [College of Pharmacy, Kyung Hee University, Seoul (Korea, Republic of); Ryu, Jung Bok [R and D Center, Chuncheon (Korea, Republic of)

2017-02-15

Lithium halide-based molten salts (LiX-[BMIm]Br) synthesized from the reactions of lithium halides (LiX, X = Cl or Br) with 1-butyl-3-methylimidazolium bromide ([BMIm]Br), and their catalytic performances and corrosivities were tested for the coupling reactions of ethylene oxide with carbon dioxide to produce ethylene carbonate. The activity of a molten salt was influenced with the change of halide ion. At a fixed molar amount of LiX, the activity of LiX-[BMIm]Br increased with increasing molar ratio of LiX/[BMIm]Br up to 1–1.25, and then decreased thereafter. Fast atom bombardment mass spectral analysis of LiBr-[BMIm]Br, obtained by dissolving LiBr in [BMIm]Br in a 1:1 molar ratio, implies that [Li{sub a} X{sub a+1}]{sup −} are active species for the carboxylation of ethylene oxide with LiX-[BMIm]Br. The corrosion test toward carbon steel coupons demonstrates that all the Cl-containing molten salts are corrosive, whereas the salts without containing Cl{sup −} are non-corrosive under the carboxylation condition.

Ni-doped (CeO{sub 2−δ})–YSZ mesoarchitectured with nanocrystalline framework: the effect of thermal treatment on structure, surface chemistry and catalytic properties in the partial oxidation of methane (CPOM)

Energy Technology Data Exchange (ETDEWEB)

Somacescu, Simona, E-mail: ssimona@icf.ro [Romanian Academy, “Ilie Murgulescu” Institute of Physical Chemistry (Romania); Florea, Mihaela [University of Bucharest, Department of Organic Chemistry, Biochemistry and Catalysis, Faculty of Chemistry (Romania); Osiceanu, Petre; Calderon-Moreno, Jose Maria [Romanian Academy, “Ilie Murgulescu” Institute of Physical Chemistry (Romania); Ghica, Corneliu [National Institute of Materials Physics (Romania); Serra, Jose Manuel [Universidad Politécnica de Valencia - Consejo Superior de Investigaciones Científicas, Instituto de Tecnología Química (Spain)

2015-11-15

Ni-doped (CeO{sub 2−δ})–YSZ (5 mol% Ni oxide, 10 mol% ceria) mesoarchitectures (MA) with nanocrystalline framework have been synthesized by an original, facile and cheap approach based on Triton X100 nonionic surfactant as template and water as solvent at a strong basic pH value. Following the hydrothermal treatment under autogenous pressure (∼18 bars), Ni, Ce, Y, and Zr were well ordered as MA with nanocrystalline framework, assuring thermal stability. A comprehensive investigation of structure, texture, morphology, and surface chemistry was performed by means of a variety of complementary techniques (X-Ray Diffraction, XRD; Raman Spectroscopy, RS; Brunauer—Emmett—Teller, BET; Temperature—Programmed Reduction, TPR; Transmission Electron Microscopy, TEM and DF-STEM; X-ray Photoelectron Spectroscopy, XPS; Catalytic activity and selectivity). N{sub 2} sorption measurements highlighted that the mesoporous structure is formed at 600 °C and remains stable at 800 °C. At 900 °C, the MA collapses, favoring the formation of macropores. The XRD and Raman Spectroscopy of all samples showed the presence of a pure, single phase with fluorite-type structure. At 900 °C, an increased tetragonal distortion of the cubic lattice was observed. The surface chemistry probed by XPS exhibits a mixture of oxidation states (Ce{sup 3+} + Ce{sup 4+}) with high percentage of Ce{sup 3+} valence state ∼35 % and (Ni{sup 3+} and Ni{sup 2+}) oxidation states induced by the thermal treatment. These nanoparticles assembled into MA show high stability and selectivity over time in catalytic partial oxidation of methane (CPOM). These promising performances suggest an interesting prospect for introduction as anode within IT-SOFC assemblies.Graphical Abstract.

Partially massless higher-spin theory

Energy Technology Data Exchange (ETDEWEB)

Brust, Christopher [Perimeter Institute for Theoretical Physics,31 Caroline St. N, Waterloo, Ontario N2L 2Y5 (Canada); Hinterbichler, Kurt [CERCA, Department of Physics, Case Western Reserve University,10900 Euclid Ave, Cleveland, OH 44106 (United States)

2017-02-16

We study a generalization of the D-dimensional Vasiliev theory to include a tower of partially massless fields. This theory is obtained by replacing the usual higher-spin algebra of Killing tensors on (A)dS with a generalization that includes “third-order” Killing tensors. Gauging this algebra with the Vasiliev formalism leads to a fully non-linear theory which is expected to be UV complete, includes gravity, and can live on dS as well as AdS. The linearized spectrum includes three massive particles and an infinite tower of partially massless particles, in addition to the usual spectrum of particles present in the Vasiliev theory, in agreement with predictions from a putative dual CFT with the same symmetry algebra. We compute the masses of the particles which are not fixed by the massless or partially massless gauge symmetry, finding precise agreement with the CFT predictions. This involves computing several dozen of the lowest-lying terms in the expansion of the trilinear form of the enlarged higher-spin algebra. We also discuss nuances in the theory that occur in specific dimensions; in particular, the theory dramatically truncates in bulk dimensions D=3,5 and has non-diagonalizable mixings which occur in D=4,7.

Partially massless higher-spin theory

International Nuclear Information System (INIS)

Brust, Christopher; Hinterbichler, Kurt

2017-01-01

We study a generalization of the D-dimensional Vasiliev theory to include a tower of partially massless fields. This theory is obtained by replacing the usual higher-spin algebra of Killing tensors on (A)dS with a generalization that includes “third-order” Killing tensors. Gauging this algebra with the Vasiliev formalism leads to a fully non-linear theory which is expected to be UV complete, includes gravity, and can live on dS as well as AdS. The linearized spectrum includes three massive particles and an infinite tower of partially massless particles, in addition to the usual spectrum of particles present in the Vasiliev theory, in agreement with predictions from a putative dual CFT with the same symmetry algebra. We compute the masses of the particles which are not fixed by the massless or partially massless gauge symmetry, finding precise agreement with the CFT predictions. This involves computing several dozen of the lowest-lying terms in the expansion of the trilinear form of the enlarged higher-spin algebra. We also discuss nuances in the theory that occur in specific dimensions; in particular, the theory dramatically truncates in bulk dimensions D=3,5 and has non-diagonalizable mixings which occur in D=4,7.

Large stability and high catalytic activities of sub-nm metal (0) clusters: implications into the nucleation and growth theory.

Science.gov (United States)

Piñeiro, Yolanda; Buceta, David; Calvo, Javier; Huseyinova, Shahana; Cuerva, Miguel; Pérez, Ángel; Domínguez, Blanca; López-Quintela, M Arturo

2015-07-01

Clusters are stable catalytic species, which are produced during the synthesis of nanoparticles (NPs). Their existence contradicts the thermodynamic principles used to explain the formation of NPs by the classical nucleation and growth theories (NGTs). Using chemical and electrochemical methods we will show that depending on the experimental conditions one can produce either Ag clusters or Ag NPs. Moreover, using already prepared Ag clusters one can observe the disappearance of the usual induction period observed for the kinetics of NP formation, indicating that clusters catalyze the formation of NPs. Taking these data together with some previous examples of cluster-catalyzed anisotropic growth, we derived a qualitative approach to include the catalytic activities of clusters into the formation of NPs, which is incorporated into the NGT. Some qualitative conclusions about the main experimental parameters, which affect the formation of clusters versus NPs, as well as the catalytic mechanism versus the non-catalytic one, are also described. Copyright © 2015 Elsevier Inc. All rights reserved.

Electrochemical promotion of sulfur dioxide catalytic oxidation

DEFF Research Database (Denmark)

Petrushina, Irina; Bandur, Viktor; Cappeln, Frederik Vilhelm

2000-01-01

investigation was to study a possible non-Faradaic electrochemical promotion of the liquid-phase catalytic reaction. It has been shown that there are two negative potential promotion areas with maximum effects at approximately -0.1 and -0.2 V, and one positive potential promotion area with the maximum effect...... between 0.1 and 0.3 V. There were no Faradaic reactions in the negative polarization region, and there was an anodic current which was less than 16% of the theoretical value for an exclusively Faradaic SO2 oxidation. Therefore the promotion effects at negative polarization are completely non-Faradaic. All...... the promotion effects have been explained as mainly due to charging of the electric double layer at the gold electrode. The effect at -0.2 V also depends on the V2O5 concentration and is more pronounced at higher V2O5 concentrations. This has been ascribed to a destruction of the vanadium polymeric chains...

Engineering Metallic Nanoparticles for Enhancing and Probing Catalytic Reactions.

Science.gov (United States)

Collins, Gillian; Holmes, Justin D

2016-07-01

Recent developments in tailoring the structural and chemical properties of colloidal metal nanoparticles (NPs) have led to significant enhancements in catalyst performance. Controllable colloidal synthesis has also allowed tailor-made NPs to serve as mechanistic probes for catalytic processes. The innovative use of colloidal NPs to gain fundamental insights into catalytic function will be highlighted across a variety of catalytic and electrocatalytic applications. The engineering of future heterogenous catalysts is also moving beyond size, shape and composition considerations. Advancements in understanding structure-property relationships have enabled incorporation of complex features such as tuning surface strain to influence the behavior of catalytic NPs. Exploiting plasmonic properties and altering colloidal surface chemistry through functionalization are also emerging as important areas for rational design of catalytic NPs. This news article will highlight the key developments and challenges to the future design of catalytic NPs. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

MAP: an iterative experimental design methodology for the optimization of catalytic search space structure modeling.

Science.gov (United States)

Baumes, Laurent A

2006-01-01

One of the main problems in high-throughput research for materials is still the design of experiments. At early stages of discovery programs, purely exploratory methodologies coupled with fast screening tools should be employed. This should lead to opportunities to find unexpected catalytic results and identify the "groups" of catalyst outputs, providing well-defined boundaries for future optimizations. However, very few new papers deal with strategies that guide exploratory studies. Mostly, traditional designs, homogeneous covering, or simple random samplings are exploited. Typical catalytic output distributions exhibit unbalanced datasets for which an efficient learning is hardly carried out, and interesting but rare classes are usually unrecognized. Here is suggested a new iterative algorithm for the characterization of the search space structure, working independently of learning processes. It enhances recognition rates by transferring catalysts to be screened from "performance-stable" space zones to "unsteady" ones which necessitate more experiments to be well-modeled. The evaluation of new algorithm attempts through benchmarks is compulsory due to the lack of past proofs about their efficiency. The method is detailed and thoroughly tested with mathematical functions exhibiting different levels of complexity. The strategy is not only empirically evaluated, the effect or efficiency of sampling on future Machine Learning performances is also quantified. The minimum sample size required by the algorithm for being statistically discriminated from simple random sampling is investigated.

Hydrocarbon conversion with an attenuated superactive multimetallic catalytic composite

International Nuclear Information System (INIS)

Antos, G.J.

1981-01-01

Hydrocarbons are converted by contacting them at hydrocarbon conversion conditions with a novel attenuated superactive multimetallic catalytic composite comprising a combination of a catalytically effective amount of a pyrolyzed rhenium carbonyl component with a porous carrier material containing a uniform dispersion of catalytically effective amounts of a platinum group component, which is maintained in the elemental metallic state during the incorporation and pyrolysis of the rhenium carbonyl component, and of an iron component. In a highly preferred embodiment, this novel catalytic composite also contains a catalytically effective amount of a halogen component. The platinum group component, pyrolyzed rhenium carbonyl component, iron component and optional halogen component are preferably present in the multimetallic catalytic composite in amounts, calculated on an elemental basis, corresponding to about 0.01 to about 2 wt. % platinum group metal, about 0.01 to about 5 wt. % rhenium, about 0.005 to about 4 wt. % iron and about 0.1 to about 5 wt. % halogen. A key feature associated with the preparation of the subject catalytic composite is reaction of a rhenium carbonyl complex with a porous carrier material containing a uniform dispersion of an iron component and of a platinum group component maintained in the elemental state, whereby the interaction of the rhenium moiety with the platinum group moiety is maximized due to the platinophilic (i.e., platinum-seeking) propensities of the carbon monoxide ligands associated with the rhenium reagent. A specific example of the type of hydrocarbon conversion process disclosed herein is a process for the catalytic reforming of a low octane gasoline fraction wherein the gasoline fraction and a hydrogen stream are contacted with the attenuated superactive multimetallic catalytic composite at reforming conditions

Catalytic thermometric titrations in non-aqueous solvents by coulometrically generated titrant.

Science.gov (United States)

Vajgand, V J; Gaál, F F; Brusin, S S

1970-05-01

Catalytic thermometric titrations have been developed for tertiary amines and salts of organic acids in acetic and propionic anhydride with titrant coulometrically generated at a mercury and/or platinum anode, hydroquinone being added to the solution titrated if the platinum anode is used. The results obtained are compared with those obtained by coulometric titration with the end-point detected either photometrically or potentiometrically. On a élaboré des titrages thermométriques catalytiques pour les amines tertiaires et les sels d'acides organiques en anhydrides aétique et propionique avec l'agent de titrage engendré coulométriquement sur une anode de mercure et/ou platine, de l'hydroquinone étant ajoutée à la solution titrée si l'on emploie l'anode de platine. Les résultats obtenus sont comparés avec ceux obtenus par titrage coulométrique avec le point de fin de réaction détecté soit photométriquement soit potentioétriquement.

Catalytic treatment

Energy Technology Data Exchange (ETDEWEB)

Bindley, W T.R.

1931-04-18

An apparatus is described for the catalytic treatment of liquids, semi-liquids, and gases comprising a vessel into which the liquid, semi-liquid, or gas to be treated is introduced through a common inlet to a chamber within the vessel whence it passes to contact with a catalyst through radially arranged channels or passages to a common outlet chamber.

Ultrafast quantum random number generation based on quantum phase fluctuations.

Science.gov (United States)

Xu, Feihu; Qi, Bing; Ma, Xiongfeng; Xu, He; Zheng, Haoxuan; Lo, Hoi-Kwong

2012-05-21

A quantum random number generator (QRNG) can generate true randomness by exploiting the fundamental indeterminism of quantum mechanics. Most approaches to QRNG employ single-photon detection technologies and are limited in speed. Here, we experimentally demonstrate an ultrafast QRNG at a rate over 6 Gbits/s based on the quantum phase fluctuations of a laser operating near threshold. Moreover, we consider a potential adversary who has partial knowledge on the raw data and discuss how one can rigorously remove such partial knowledge with postprocessing. We quantify the quantum randomness through min-entropy by modeling our system and employ two randomness extractors--Trevisan's extractor and Toeplitz-hashing--to distill the randomness, which is information-theoretically provable. The simplicity and high-speed of our experimental setup show the feasibility of a robust, low-cost, high-speed QRNG.

Numerical study of the behavior of methane-hydrogen/air pre-mixed flame in a micro reactor equipped with catalytic segmented bluff body

International Nuclear Information System (INIS)

Baigmohammadi, Mohammadreza; Tabejamaat, Sadegh; Zarvandi, Jalal

2015-01-01

In this work, combustion characteristics of premixed methane-hydrogen/air in a micro reactor equipped with a catalytic bluff body is investigated numerically. In this regard, the detailed chemistry schemes for gas phase (homogeneous) and the catalyst surface (heterogeneous) are used. The applied catalytic bluff body is coated with a thin layer of platinum (Pt) on its surface. Also, the lean reactive mixture is entered to the reactor with equivalence ratio 0.9. The results of this study showed that the use of catalytic bluff body in the center of a micro reactor can significantly increase the flame stability, especially at high velocities. Moreover, it is found that a catalytic bluff body with several cavities on its surface and also high thermal conductivity improves the flame stability more than a catalytic bluff body without cavities and low thermal conductivity. Finally, it is maintained that the most advantage of using the catalytic bluff body is its easy manufacturing process as compared to the catalytic wall. This matter seems to be more prevalent when we want to create several cavities with various sizes on the bluff-body. - Highlights: • Presence of a bluff body in a micro reactor can move the flame towards the upstream. • Catalytic bluff body can significantly increase flame stability at high velocities. • Creating non-catalytic cavities on the bluff body promotes homogeneous reactions. • Segmented catalytic bluff body improves the flame stability more than a simple one. • Creating the segments on a bluff body is easier compared to a wall

Non-existence of bipartite bound entanglement with negative partial transposition

OpenAIRE

Sperling, J.; Vogel, W.

2009-01-01

Bound entanglement with a nonpositive partial transposition (NPT) does not exist. For any NPT entangled state a distillation procedure can be based on a certain number of copies. This number is the minimal Schmidt rank of a pure state needed to witness the NPT entanglement under study.

Catalytic cleavage activities of 10–23 DNAzyme analogs functionalized with an amino group in its catalytic core

Directory of Open Access Journals (Sweden)

Qi Wang

2012-02-01

Full Text Available Functionalization of the catalytic loop of 10–23 DNAzyme with an amino group was performed by incorporation of 7-(3-aminopropyl-8-aza-7-deaza-2′-deoxyadenosine in different single positions. Among the nine modified positions in the catalytic loop, A9 is the unique position with positive contribution by such modification. These results indicated that more efficient deoxyribozymes remain to be explored by introduction of exogenous functional groups in an appropriate position in the catalytic loop of 10–23 DNAzyme, such as the combination of 7-functional group substituted 8-aza-7-deaza-2′-deoxyadenosine analogs and A9 position.

Stability for Function Trade-Offs in the Enolase Superfamily 'Catalytic Module'

Energy Technology Data Exchange (ETDEWEB)

Nagatani, R.A.; Gonzalez, A.; Shoichet, B.K.; Brinen, L.S.; Babbitt, P.C.; /UC, San Francisco /SLAC, SSRL

2007-07-12

Enzyme catalysis reflects a dynamic interplay between charged and polar active site residues that facilitate function, stabilize transition states, and maintain overall protein stability. Previous studies show that substituting neutral for charged residues in the active site often significantly stabilizes a protein, suggesting a stability trade-off for functionality. In the enolase superfamily, a set of conserved active site residues (the ''catalytic module'') has repeatedly been used in nature in the evolution of many different enzymes for the performance of unique overall reactions involving a chemically diverse set of substrates. This catalytic module provides a robust solution for catalysis that delivers the common underlying partial reaction that supports all of the different overall chemical reactions of the superfamily. As this module has been so broadly conserved in the evolution of new functions, we sought to investigate the extent to which it follows the stability-function trade-off. Alanine substitutions were made for individual residues, groups of residues, and the entire catalytic module of o-succinylbenzoate synthase (OSBS), a member of the enolase superfamily from Escherichia coli. Of six individual residue substitutions, four (K131A, D161A, E190A, and D213A) substantially increased protein stability (by 0.46-4.23 kcal/mol), broadly consistent with prediction of a stability-activity trade-off. The residue most conserved across the superfamily, E190, is by far the most destabilizing. When the individual substitutions were combined into groups (as they are structurally and functionally organized), nonadditive stability effects emerged, supporting previous observations that residues within the module interact as two functional groups within a larger catalytic system. Thus, whereas the multiple-mutant enzymes D161A/E190A/D213A and K131A/K133A/D161A/E190A/D213A/K235A (termed 3KDED) are stabilized relative to the wild-type enzyme (by 1

Random and non-random mating populations: Evolutionary dynamics in meiotic drive.

Science.gov (United States)

Sarkar, Bijan

2016-01-01

Game theoretic tools are utilized to analyze a one-locus continuous selection model of sex-specific meiotic drive by considering nonequivalence of the viabilities of reciprocal heterozygotes that might be noticed at an imprinted locus. The model draws attention to the role of viability selections of different types to examine the stable nature of polymorphic equilibrium. A bridge between population genetics and evolutionary game theory has been built up by applying the concept of the Fundamental Theorem of Natural Selection. In addition to pointing out the influences of male and female segregation ratios on selection, configuration structure reveals some noted results, e.g., Hardy-Weinberg frequencies hold in replicator dynamics, occurrence of faster evolution at the maximized variance fitness, existence of mixed Evolutionarily Stable Strategy (ESS) in asymmetric games, the tending evolution to follow not only a 1:1 sex ratio but also a 1:1 different alleles ratio at particular gene locus. Through construction of replicator dynamics in the group selection framework, our selection model introduces a redefining bases of game theory to incorporate non-random mating where a mating parameter associated with population structure is dependent on the social structure. Also, the model exposes the fact that the number of polymorphic equilibria will depend on the algebraic expression of population structure. Copyright © 2015 Elsevier Inc. All rights reserved.

Improving the conversion of biomass in catalytic fast pyrolysis via white-rot fungal pretreatment.

Science.gov (United States)

Yu, Yanqing; Zeng, Yelin; Zuo, Jiane; Ma, Fuying; Yang, Xuewei; Zhang, Xiaoyu; Wang, Yujue

2013-04-01

This study investigated the effect of white-rot fungal pretreatment on corn stover conversion in catalytic fast pyrolysis (CFP). Corn stover pretreated by white-rot fungus Irpex lacteus CD2 was fast pyrolyzed alone (non-CFP) and with ZSM-5 zeolite (CFP) in a semi-batch pyroprobe reactor. The fungal pretreatment considerably increased the volatile product yields (predominantly oxygenated compounds) in non-CFP, indicating that fungal pretreatment enhances the corn stover conversion in fast pyrolysis. In the presence of ZSM-5 zeolite, these oxygenated volatiles were further catalytically converted to aromatic hydrocarbons, whose yield increased from 10.03 wt.% for the untreated corn stover to 11.49 wt.% for the pretreated sample. In contrast, the coke yield decreased from 14.29 to 11.93 wt.% in CFP following the fungal pretreatment. These results indicate that fungal pretreatment can enhance the production of valuable aromatics and decrease the amount of undesired coke, and thus has a beneficial effect on biomass conversion in CFP. Copyright © 2013 Elsevier Ltd. All rights reserved.

Neuromuscular Exercise Post Partial Medial Meniscectomy

DEFF Research Database (Denmark)

Hall, Michelle; Hinman, Rana S; Wrigley, Tim V

2015-01-01

PURPOSE: To evaluate the effects of a 12-week, home-based, physiotherapist-guided neuromuscular exercise program on the knee adduction moment (an indicator of mediolateral knee load distribution) in people with a medial arthroscopic partial meniscectomy within the past 3-12 months. METHODS......: An assessor-blinded, randomised controlled trial including people aged 30-50 years with no to mild pain following medial arthroscopic partial meniscectomy was conducted. Participants were randomly allocated to either a 12-week neuromuscular exercise program that targeted neutral lower limb alignment...... or a control group with no exercise. The exercise program included eight individual sessions with one of seven physiotherapists in private clinics, together with home exercises. Primary outcomes were the peak external knee adduction moment during normal pace walking and during a one-leg sit-to-stand. Secondary...

Discovering non-random segregation of sister chromatids: The naïve treatment of a premature discovery

Directory of Open Access Journals (Sweden)

Karl G. Lark

2013-02-01

Full Text Available The discovery of non-random chromosome segregation is discussed from the perspective of what was known in1965 and1966. The distinction between daughter, parent or grandparent strands of DNA was developed in a bacterial system and led to the discovery that multiple copies of DNA elements of bacteria are not distributed randomly with respect to the age of the template strand. Experiments with higher eukaryotic cells demonstrated that during mitosis Mendel’s laws were violated; and the initial serendipitous choice of eukaryotic cell system led to the striking example of non-random segregation of parent and grand-parent DNA template strands in primary cultures of cells derived from mouse embryos. Attempts to extrapolate these findings to established TC lines demonstrated that the property could be lost. Experiments using plant root tips demonstrated that the phenomenon exists in plants and that it was, at some level, under genetic control. Despite publication in major journals and symposia (Lark et al. (1966a; Lark (1967a; 1967b; 1969, 1969a; 1969b the potential implications of these findings were ignored for several decades. Here we explore possible reasons for the pre-maturity (Stent, 1972 of this discovery.

Variation of mutational burden in healthy human tissues suggests non-random strand segregation and allows measuring somatic mutation rates.

Science.gov (United States)

Werner, Benjamin; Sottoriva, Andrea

2018-06-01

The immortal strand hypothesis poses that stem cells could produce differentiated progeny while conserving the original template strand, thus avoiding accumulating somatic mutations. However, quantitating the extent of non-random DNA strand segregation in human stem cells remains difficult in vivo. Here we show that the change of the mean and variance of the mutational burden with age in healthy human tissues allows estimating strand segregation probabilities and somatic mutation rates. We analysed deep sequencing data from healthy human colon, small intestine, liver, skin and brain. We found highly effective non-random DNA strand segregation in all adult tissues (mean strand segregation probability: 0.98, standard error bounds (0.97,0.99)). In contrast, non-random strand segregation efficiency is reduced to 0.87 (0.78,0.88) in neural tissue during early development, suggesting stem cell pool expansions due to symmetric self-renewal. Healthy somatic mutation rates differed across tissue types, ranging from 3.5 × 10-9/bp/division in small intestine to 1.6 × 10-7/bp/division in skin.

Variation of mutational burden in healthy human tissues suggests non-random strand segregation and allows measuring somatic mutation rates.

Directory of Open Access Journals (Sweden)

Benjamin Werner

2018-06-01

Full Text Available The immortal strand hypothesis poses that stem cells could produce differentiated progeny while conserving the original template strand, thus avoiding accumulating somatic mutations. However, quantitating the extent of non-random DNA strand segregation in human stem cells remains difficult in vivo. Here we show that the change of the mean and variance of the mutational burden with age in healthy human tissues allows estimating strand segregation probabilities and somatic mutation rates. We analysed deep sequencing data from healthy human colon, small intestine, liver, skin and brain. We found highly effective non-random DNA strand segregation in all adult tissues (mean strand segregation probability: 0.98, standard error bounds (0.97,0.99. In contrast, non-random strand segregation efficiency is reduced to 0.87 (0.78,0.88 in neural tissue during early development, suggesting stem cell pool expansions due to symmetric self-renewal. Healthy somatic mutation rates differed across tissue types, ranging from 3.5 × 10-9/bp/division in small intestine to 1.6 × 10-7/bp/division in skin.

Catalytic ozonation not relying on hydroxyl radical oxidation: A selective and competitive reaction process related to metal-carboxylate complexes

KAUST Repository

Zhang, Tao; Croue, Jean-Philippe

2014-01-01

Catalytic ozonation following non-hydroxyl radical pathway is an important technique not only to degrade refractory carboxylic-containing organic compounds/matter but also to avoid catalyst deactivation caused by metal-carboxylate complexation

Synergy Effects of the Mixture of Bismuth Molybdate Catalysts with SnO2/ZrO2/MgO in Selective Propene Oxidation and the Connection between Conductivity and Catalytic Activity

DEFF Research Database (Denmark)

Le, Minh Thang; Do, Van Hung; Truong, Duc Duc

2016-01-01

Bismuth molybdate catalysts have been used for partial oxidation and ammoxidation of light hydrocarbons since the 1950s. In particular, there is the synergy effect (the enhancement of the catalytic activity in the catalysts mixed from different components) in different phases of bismuth molybdate...... catalysts which has been observed and studied since the 1980s; however, despite it being interpreted differently by different research groups, there is still no decisive conclusion on the origin of the synergy effect that has been obtained. The starting idea of this work is to find an answer......, impregnation, and sol-gel methods. The mixtures were characterized by XRD, BET, XPS, and EDX techniques to determine the phase composition and surface properties. The conductivities of these samples were recorded at the catalytic reaction temperature (300-450 degrees C). Comparison of the catalytic activities...

Review of Heterogeneous Catalysts for Catalytically Upgrading Vegetable Oils into Hydrocarbon Biofuels

OpenAIRE

Xianhui Zhao; Lin Wei; Shouyun Cheng; James Julson

2017-01-01

To address the issues of greenhouse gas emissions associated with fossil fuels, vegetable oilseeds, especially non-food oilseeds, are used as an alternative fuel resource. Vegetable oil derived from these oilseeds can be upgraded into hydrocarbon biofuel. Catalytic cracking and hydroprocessing are two of the most promising pathways for converting vegetable oil to hydrocarbon biofuel. Heterogeneous catalysts play a critical role in those processes. The present review summarizes current progres...

Exploring the importance of different items as reasons for leaving emergency medical services between fully compensated, partially compensated, and non-compensated/volunteer samples.

Science.gov (United States)

Blau, Gary; Chapman, Susan; Gibson, Gregory; Bentley, Melissa A

2011-01-01

The purpose of our study was to investigate the importance of different items as reasons for leaving the Emergency Medical Service (EMS) profession. An exit survey was returned by three distinct EMS samples: 127 full compensated, 45 partially compensated and 72 non-compensated/volunteer respondents, who rated the importance of 17 different items for affecting their decision to leave EMS. Unfortunately, there were a high percentage of "not applicable" responses for 10 items. We focused on those seven items that had a majority of useable responses across the three samples. Results showed that the desire for better pay and benefits was a more important reason for leaving EMS for the partially compensated versus fully compensated respondents. Perceived lack of advancement opportunity was a more important reason for leaving for the partially compensated and volunteer groups versus the fully compensated group. Study limitations are discussed and suggestions for future research offered.

Partial Correlation Matrix Estimation using Ridge Penalty Followed by Thresholding and Reestimation

Science.gov (United States)

2014-01-01

Summary Motivated by the problem of construction gene co-expression network, we propose a statistical framework for estimating high-dimensional partial correlation matrix by a three-step approach. We first obtain a penalized estimate of a partial correlation matrix using ridge penalty. Next we select the non-zero entries of the partial correlation matrix by hypothesis testing. Finally we reestimate the partial correlation coefficients at these non-zero entries. In the second step, the null distribution of the test statistics derived from penalized partial correlation estimates has not been established. We address this challenge by estimating the null distribution from the empirical distribution of the test statistics of all the penalized partial correlation estimates. Extensive simulation studies demonstrate the good performance of our method. Application on a yeast cell cycle gene expression data shows that our method delivers better predictions of the protein-protein interactions than the Graphic Lasso. PMID:24845967

Association Between Telomere Length and Risk of Cancer and Non-Neoplastic Diseases: A Mendelian Randomization Study

NARCIS (Netherlands)

Haycock, P.C.; Burgess, S.; Nounu, A.; Zheng, J.; Okoli, G.N.; Bowden, J.; Wade, K.H.; Timpson, N.J.; Evans, D.M.; Willeit, P.; Aviv, A.; Gaunt, T.R.; Hemani, G.; Mangino, M.; Ellis, H.P.; Kurian, K.M.; Pooley, K.A.; Eeles, R.A.; Lee, J.E.; Fang, S.; Chen, W.V.; Law, M.H.; Bowdler, L.M.; Iles, M.M.; Yang, Q.; Worrall, B.B.; Markus, H.S.; Hung, R.J.; Amos, C.I.; Spurdle, A.B.; Thompson, D.J.; O'Mara, T.A.; Wolpin, B.; Amundadottir, L.; Stolzenberg-Solomon, R.; Trichopoulou, A.; Onland-Moret, N.C.; Lund, E.; Duell, E.J.; Canzian, F.; Severi, G.; Overvad, K.; Gunter, M.J.; Tumino, R.; Svenson, U.; Rij, A. van; Baas, A.F.; Bown, M.J.; Samani, N.J.; t'Hof, F.N.G. van; Tromp, G.; Jones, G.T.; Kuivaniemi, H.; Elmore, J.R.; Johansson, M.; McKay, J.; Scelo, G.; Carreras-Torres, R.; Gaborieau, V.; Brennan, P.; Bracci, P.M.; Neale, R.E.; Olson, S.H.; Gallinger, S.; Li, D.; Petersen, G.M.; Risch, H.A.; Klein, A.P.; Han, J.; Abnet, C.C.; Freedman, N.D.; Taylor, P.R.; Maris, J.M.; Aben, K.K.H.; Kiemeney, L.A.; Vermeulen, S.H.; Wiencke, J.K.; Walsh, K.M.; Wrensch, M.; Rice, T.; Turnbull, C.; Litchfield, K.; Paternoster, L.; Standl, M.; Abecasis, G.R.; SanGiovanni, J.P.; Li, Y.; Mijatovic, V.; Sapkota, Y.; Low, S.K.; Zondervan, K.T.; Montgomery, G.W.; Nyholt, D.R.; Heel, D.A. van; Hunt, K.; Arking, D.E.; Ashar, F.N.; Sotoodehnia, N.; Woo, D.; et al.,

2017-01-01

Importance: The causal direction and magnitude of the association between telomere length and incidence of cancer and non-neoplastic diseases is uncertain owing to the susceptibility of observational studies to confounding and reverse causation. Objective: To conduct a Mendelian randomization study,

Progress in catalytic naphtha reforming process: A review

International Nuclear Information System (INIS)

Rahimpour, Mohammad Reza; Jafari, Mitra; Iranshahi, Davood

2013-01-01

Catalytic naphtha reforming process is a vital process for refineries due to the production of high-octane components, which is intensely demanded in our modern life. The significance of this industrial process induced researchers to investigate different aspects of catalytic naphtha reforming process intensively. Some of the investigators try to improve this process by representing more effective catalysts, while others try to elucidate its kinetic and deactivation mechanisms and design more efficient reactor setups. The amount of these established papers is so much that may confuse some of the researchers who want to find collective information about catalytic naphtha reforming process. In the present paper, the published studies from 1949 until now are categorized into three main groups including finding suitable catalyst, revealing appropriate kinetic and deactivation model, and suggesting efficient reactor configuration and mode of operation. These studies are reviewed separately, and a suitable reference is provided for those who want to have access to generalized information about catalytic naphtha reforming process. Finally, various suggestions for revamping the catalytic naphtha reforming process have been proposed as a guideline for further investigations

Flow in Random Microstructures: a Multilevel Monte Carlo Approach

KAUST Repository

Icardi, Matteo; Tempone, Raul

2016-01-01

, where an explicit parametrisation of the input randomness is not available or too expensive. We propose a general-purpose algorithm and computational code for the solution of Partial Differential Equations (PDEs) on random heterogeneous materials. We

Plasma-catalytic decomposition of TCE

Energy Technology Data Exchange (ETDEWEB)

Vandenbroucke, A.; Morent, R.; De Geyter, N.; Leys, C. [Ghent Univ., Ghent (Belgium). Dept. of Applied Physics; Tuan, N.D.M.; Giraudon, J.M.; Lamonier, J.F. [Univ. des Sciences et Technologies de Lille, Villeneuve (France). Dept. de Catalyse et Chimie du Solide

2010-07-01

Volatile organic compounds (VOCs) are gaseous pollutants that pose an environmental hazard due to their high volatility and their possible toxicity. Conventional technologies to reduce the emission of VOCs have their advantages, but they become cost-inefficient when low concentrations have to be treated. In the past 2 decades, non-thermal plasma technology has received growing attention as an alternative and promising remediation method. Non-thermal plasmas are effective because they produce a series of strong oxidizers such as ozone, oxygen radicals and hydroxyl radicals that provide a reactive chemical environment in which VOCs are completely oxidized. This study investigated whether the combination of NTP and catalysis could improve the energy efficiency and the selectivity towards carbon dioxide (CO{sub 2}). Trichloroethylene (TCE) was decomposed by non-thermal plasma generated in a DC-excited atmospheric pressure glow discharge. The production of by-products was qualitatively investigated through FT-IR spectrometry. The results were compared with those from a catalytic reactor. The removal rate of TCE reached a maximum of 78 percent at the highest input energy. The by-products of TCE decomposition were CO{sub 2}, carbon monoxide (CO) hydrochloric acid (HCl) and dichloroacetylchloride. Combining the plasma system with a catalyst located in an oven downstream resulted in a maximum removal of 80 percent, at an energy density of 300 J/L, a catalyst temperature of 373 K and a total air flow rate of 2 slm. 14 refs., 6 figs.

Non-random mating and convergence over time for alcohol consumption, smoking, and exercise: the Nord-Trøndelag Health Study.

Science.gov (United States)

Ask, Helga; Rognmo, Kamilla; Torvik, Fartein Ask; Røysamb, Espen; Tambs, Kristian

2012-05-01

Spouses tend to have similar lifestyles. We explored the degree to which spouse similarity in alcohol use, smoking, and physical exercise is caused by non-random mating or convergence. We used data collected for the Nord-Trøndelag Health Study from 1984 to 1986 and prospective registry information about when and with whom people entered marriage/cohabitation between 1970 and 2000. Our sample included 19,599 married/cohabitating couples and 1,551 future couples that were to marry/cohabitate in the 14-16 years following data collection. All couples were grouped according to the duration between data collection and entering into marriage/cohabitation. Age-adjusted polychoric spouse correlations were used as the dependent variables in non-linear segmented regression analysis; the independent variable was time. The results indicate that spouse concordance in lifestyle is due to both non-random mating and convergence. Non-random mating appeared to be strongest for smoking. Convergence in alcohol use and smoking was evident during the period prior to marriage/cohabitation, whereas convergence in exercise was evident throughout life. Reduced spouse similarity in smoking with relationship duration may reflect secular trends.

Treatment with silver nitrate versus topical steroid treatment for umbilical granuloma: A non-inferiority randomized control trial.

Directory of Open Access Journals (Sweden)

Chikako Ogawa

Full Text Available The aim of this prospective multicenter randomized controlled trial was to compare the efficacy of silver nitrate cauterization against that of topical steroid ointment in the treatment of neonatal umbilical granuloma.An open-label, non-inferiority randomized controlled trial was conducted from January 2013 to January 2016. The primary endpoint for the silver nitrate cauterization and topical steroid ointment groups was the healing rate after 2 weeks of treatment, applying a non-inferiority margin of 10%. The healing rate was evaluated until completion of 3 weeks of treatment.Participants comprised 207 neonates with newly diagnosed umbilical granuloma, randomized to receive silver nitrate cauterization (n = 104 or topical steroid ointment (n = 103. Healing rates after 2 weeks of treatment were 87.5% (91/104 in the silver nitrate cauterization and 82% (82/100 in the topical steroid ointment group group. The difference between groups was -5.5% (95% confidence interval, -19.1%, 8.4%, indicating that the non-inferiority criterion was not met. After 3 weeks of treatment, the healing rate with topical steroid ointment treatment was almost identical to that of silver nitrate cauterization (94/104 [90.4%] vs. 91/100 [91.0%]; 0.6% [-13.2 to 14.3]. No major complications occurred in either group.This study did not establish non-inferiority of topical steroid ointment treatment relative to silver nitrate cauterization, presumably due to lower healing rates than expected leading to an underpowered trial. However, considering that silver nitrate cauterization carries a distinct risk of chemical burns and that the overall efficacy of topical steroid ointment treatment is similar to that of silver nitrate cauterization, topical steroid ointment might be considered as a good alternative in the treatment of neonatal umbilical granuloma due to its safety and simplicity. To clarify non-inferiority, a larger study is needed.

Hepatitis C virus non-structural protein 3 interacts with cytosolic 5'(3'-deoxyribonucleotidase and partially inhibits its activity.

Directory of Open Access Journals (Sweden)

Chiu-Ping Fang

Full Text Available Infection with hepatitis C virus (HCV is etiologically involved in liver cirrhosis, hepatocellular carcinoma and B-cell lymphomas. It has been demonstrated previously that HCV non-structural protein 3 (NS3 is involved in cell transformation. In this study, a yeast two-hybrid screening experiment was conducted to identify cellular proteins interacting with HCV NS3 protein. Cytosolic 5'(3'-deoxyribonucleotidase (cdN, dNT-1 was found to interact with HCV NS3 protein. Binding domains of HCV NS3 and cellular cdN proteins were also determined using the yeast two-hybrid system. Interactions between HCV NS3 and cdN proteins were further demonstrated by co-immunoprecipitation and confocal analysis in cultured cells. The cellular cdN activity was partially repressed by NS3 protein in both the transiently-transfected and the stably-transfected systems. Furthermore, HCV partially repressed the cdN activity while had no effect on its protein expression in the systems of HCV sub-genomic replicons and infectious HCV virions. Deoxyribonucleotidases are present in most mammalian cells and involve in the regulation of intracellular deoxyribonucleotides pools by substrate cycles. Control of DNA precursor concentration is essential for the maintenance of genetic stability. Reduction of cdN activity would result in the imbalance of DNA precursor concentrations. Thus, our results suggested that HCV partially reduced the cdN activity via its NS3 protein and this may in turn cause diseases.

An Adaptor Domain-Mediated Auto-Catalytic Interfacial Kinase Reaction

Science.gov (United States)

Liao, Xiaoli; Su, Jing; Mrksich, Milan

2010-01-01

This paper describes a model system for studying the auto-catalytic phosphorylation of an immobilized substrate by a kinase enzyme. This work uses self-assembled monolayers (SAMs) of alkanethiolates on gold to present the peptide substrate on a planar surface. Treatment of the monolayer with Abl kinase results in phosphorylation of the substrate. The phosphorylated peptide then serves as a ligand for the SH2 adaptor domain of the kinase and thereby directs the kinase activity to nearby peptide substrates. This directed reaction is intramolecular and proceeds with a faster rate than does the initial, intermolecular reaction, making this an auto-catalytic process. The kinetic non-linearity gives rise to properties that have no counterpart in the corresponding homogeneous phase reaction: in one example, the rate for phosphorylation of a mixture of two peptides is faster than the sum of the rates for phosphorylation of each peptide when presented alone. This work highlights the use of an adaptor domain in modulating the activity of a kinase enzyme for an immobilized substrate and offers a new approach for studying biochemical reactions in spatially inhomogeneous settings. PMID:19821459

Catalytically favorable surface patterns in Pt-Au nanoclusters

KAUST Repository

Mokkath, Junais Habeeb; Schwingenschlö gl, Udo

2013-01-01

Motivated by recent experimental demonstrations of novel PtAu nanoparticles with highly enhanced catalytic properties, we present a systematic theoretical study that explores principal catalytic indicators as a function of the particle size

Non-Equilibrium Thermodynamic Analysis of Double Diffusive, Nanofluid Forced Convection in Catalytic Microreactors with Radiation Effects

Directory of Open Access Journals (Sweden)

Lilian Govone

2017-12-01

Full Text Available This paper presents a theoretical investigation of the second law performance of double diffusive forced convection in microreactors with the inclusion of nanofluid and radiation effects. The investigated microreactors consist of a single microchannel, fully filled by a porous medium. The transport of heat and mass are analysed by including the thick walls and a first order, catalytic chemical reaction on the internal surfaces of the microchannel. Two sets of thermal boundary conditions are considered on the external surfaces of the microchannel; (1 constant temperature and (2 constant heat flux boundary condition on the lower wall and convective boundary condition on the upper wall. The local thermal non-equilibrium approach is taken to thermally analyse the porous section of the system. The mass dispersion equation is coupled with the transport of heat in the nanofluid flow through consideration of Soret effect. The problem is analytically solved and illustrations of the temperature fields, Nusselt number, total entropy generation rate and performance evaluation criterion (PEC are provided. It is shown that the radiation effect tends to modify the thermal behaviour within the porous section of the system. The radiation parameter also reduces the overall temperature of the system. It is further demonstrated that, expectedly, the nanoparticles reduce the temperature of the system and increase the Nusselt number. The total entropy generation rate and consequently PEC shows a strong relation with radiation parameter and volumetric concentration of nanoparticles.

Meta-analysis of adjunctive levetiracetam in refractory partial sei

Directory of Open Access Journals (Sweden)

ZHANG Ying

2012-10-01

Full Text Available Objective To evaluate the effects and tolerability of adjunctive levetiracetam (LEV in refractory partial seizures. Methods Relevant research articles about randomized controlled trials of adjunctive LEV in refractory partial seizures from January 1998 to December 2010 were retrieved from Cochrane Library, MEDLINE, EMbase, Social Sciences Citation Index (SSCI, VIP, Chinese National Knowledge Infrastructure (CNKI database, China Biology Medicine (CBM. Two reviewers independently evaluated the quality of the included articles and abstracted the data. A Meta-analysis was conducted by using RevMan 5.0 software. Results According to the enrollment criteria, eleven prospective, randomized controlled clinical trials with a total of 1192 in LEV group and 789 in placebo group were finally selected. The reduction in three endpoints (a 50% or greater reduction of partial seizure frequency per week, a 75% or greater reduction of partial seizure frequency per week and seizure free was significant in LEV group than placebo group. There was no significance between LEV group and placebo group in the withdrawl rate (1000 mg/d: OR = 1.180, 95%CI: 0.690-2.010, P = 0.540; 2000 mg/d: OR = 1.530, 95%CI: 0.770-3.030, P = 0.230; 3000 mg/d: OR = 1.000, 95% CI: 0.620-1.600, P = 1.000. The following adverse events were associated with LEV: somnolence (OR = 1.720, 95%CI: 1.280-2.310, P = 0.000, dizziness (OR = 1.490, 95%CI: 1.000-2.220, P = 0.050, asthenia (OR = 1.670, 95%CI: 1.140-2.240, P = 0.008, nasopharyngitis (OR = 1.120, 95% CI: 0.710-1.760, P = 0.630, psychiatric and behavioral abnormalities (OR = 2.120, 95% CI: 1.370-3.280, P = 0.000. Conclusion LEV is effective and well tolerated when added to existing therapy in patients with refractory partial seizures compared with control drugs. Further studies are needed to identify the effects of monotherapy of LEV in partial seizures.

Characterization of the catalytic center of the Ebola virus L polymerase.

Science.gov (United States)

Schmidt, Marie Luisa; Hoenen, Thomas

2017-10-01

Ebola virus (EBOV) causes a severe hemorrhagic fever in humans and non-human primates. While no licensed therapeutics are available, recently there has been tremendous progress in developing antivirals. Targeting the ribonucleoprotein complex (RNP) proteins, which facilitate genome replication and transcription, and particularly the polymerase L, is a promising antiviral approach since these processes are essential for the virus life cycle. However, until now little is known about L in terms of its structure and function, and in particular the catalytic center of the RNA-dependent RNA polymerase (RdRp) of L, which is one of the most promising molecular targets, has never been experimentally characterized. Using multiple sequence alignments with other negative sense single-stranded RNA viruses we identified the putative catalytic center of the EBOV RdRp. An L protein with mutations in this center was then generated and characterized using various life cycle modelling systems. These systems are based on minigenomes, i.e. miniature versions of the viral genome, in which the viral genes are exchanged against a reporter gene. When such minigenomes are coexpressed with RNP proteins in mammalian cells, the RNP proteins recognize them as authentic templates for replication and transcription, resulting in reporter activity reflecting these processes. Replication-competent minigenome systems indicated that our L catalytic domain mutant was impaired in genome replication and/or transcription, and by using replication-deficient minigenome systems, as well as a novel RT-qPCR-based genome replication assay, we showed that it indeed no longer supported either of these processes. However, it still showed similar expression to wild-type L, and retained its ability to be incorporated into inclusion bodies, which are the sites of EBOV genome replication. We have experimentally defined the catalytic center of the EBOV RdRp, and thus a promising antiviral target regulating an essential

Characterization of the catalytic center of the Ebola virus L polymerase.

Directory of Open Access Journals (Sweden)

Marie Luisa Schmidt

2017-10-01

Full Text Available Ebola virus (EBOV causes a severe hemorrhagic fever in humans and non-human primates. While no licensed therapeutics are available, recently there has been tremendous progress in developing antivirals. Targeting the ribonucleoprotein complex (RNP proteins, which facilitate genome replication and transcription, and particularly the polymerase L, is a promising antiviral approach since these processes are essential for the virus life cycle. However, until now little is known about L in terms of its structure and function, and in particular the catalytic center of the RNA-dependent RNA polymerase (RdRp of L, which is one of the most promising molecular targets, has never been experimentally characterized.Using multiple sequence alignments with other negative sense single-stranded RNA viruses we identified the putative catalytic center of the EBOV RdRp. An L protein with mutations in this center was then generated and characterized using various life cycle modelling systems. These systems are based on minigenomes, i.e. miniature versions of the viral genome, in which the viral genes are exchanged against a reporter gene. When such minigenomes are coexpressed with RNP proteins in mammalian cells, the RNP proteins recognize them as authentic templates for replication and transcription, resulting in reporter activity reflecting these processes. Replication-competent minigenome systems indicated that our L catalytic domain mutant was impaired in genome replication and/or transcription, and by using replication-deficient minigenome systems, as well as a novel RT-qPCR-based genome replication assay, we showed that it indeed no longer supported either of these processes. However, it still showed similar expression to wild-type L, and retained its ability to be incorporated into inclusion bodies, which are the sites of EBOV genome replication.We have experimentally defined the catalytic center of the EBOV RdRp, and thus a promising antiviral target

Catalytic Aminohalogenation of Alkenes and Alkynes.

Science.gov (United States)

Chemler, Sherry R; Bovino, Michael T

2013-06-07

Catalytic aminohalogenation methods enable the regio- and stereoselective vicinal difunctionalization of alkynes, allenes and alkenes with amine and halogen moieties. A range of protocols and reaction mechanisms including organometallic, Lewis base, Lewis acid and Brønsted acid catalysis have been disclosed, enabling the regio- and stereoselective synthesis of halogen-functionalized acyclic amines and nitrogen heterocycles. Recent advances including aminofluorination and catalytic enantioselective aminohalogenation reactions are summarized in this review.

Asymptotic distribution of products of sums of independent random ...

Indian Academy of Sciences (India)

integrable random variables (r.v.) are asymptotically log-normal. This fact ... the product of the partial sums of i.i.d. positive random variables as follows. .... Now define ..... by Henan Province Foundation and Frontier Technology Research Plan.

Direct numerical simulation of fluid-particle heat transfer in fixed random arrays of non-spherical particles

NARCIS (Netherlands)

Tavassoli Estahbanati, H.; Peters, E.A.J.F.; Kuipers, J.A.M.

2015-01-01

Direct numerical simulations are conducted to characterize the fluid-particle heat transfer coefficient in fixed random arrays of non-spherical particles. The objective of this study is to examine the applicability of well-known heat transfer correlations, that are proposed for spherical particles,

Potential for visible plume formation at a coal-fired boiler using ammonia injection for non-catalytic NOx control

International Nuclear Information System (INIS)

Hess, T.

1993-01-01

Circulating fluidized bed boilers utilizing ammonia injection for non-catalytic NO x reduction have been highly successful in reducing NO x emissions to very low levels. However, one limitation on this technology is the potential for the formation of visible plumes. One plant, with uncontrolled NO x of about 190 ppm, reduces NO x concentrations to the 20-25 ppm range by injecting ammonia in the boiler's cyclones. However, infrequent, short-lived, white, detached plumes have been noted extending for short distances downwind of the stack. Because unreacted ammonia is present in the flue gas along with HCl from coal combustion, the formation of solid NH 4 Cl in the atmosphere was suspected to be the most likely cause of the visible plume. Simple thermodynamic calculations predict the formation of solid ammonium chloride very soon after the flue gas mixes with cooler ambient air and plume optical density calculations are in reasonable agreement with observed plume density. Stack testing and other tests have been conducted during both plume and non-plume events to confirm that NH 4 Cl formation is the most likely cause of the capacity. As presented in this paper, the test data and theoretical calculations indicate that a visible plume may be expected when as little as 5 ppm of ammonia and HCl are present in the flue gas, depending on observation conditions. Analyses of fuel samples taken during stack tests show about 40% of the chlorine in the low chloride coal fired, typically less than 0.04%, is released from the stack as HCl. Ammonia slip is somewhat variable depending on combustion conditions in the boiler and the temperature at the ammonia injection points

Catalytic Conversion of Carbohydrates to Initial Platform Chemicals: Chemistry and Sustainability.

Science.gov (United States)

Mika, László T; Cséfalvay, Edit; Németh, Áron

2018-01-24

The replacement of fossil resources that currently provide more than 90% of our energy needs and feedstocks of the chemical industry in combination with reduced emission of carbon dioxide is one of the most pressing challenges of mankind. Biomass as a globally available resource has been proposed as an alternative feedstock for production of basic building blocks, which could partially or even fully replace the currently utilized fossil-based ones in well-established chemical processes. The destruction of lignocellulosic feed followed by oxygen removal from its cellulose and hemicellulose content by catalytic processes results in the formation of initial platform chemicals (IPCs). However, their sustainable production strongly depends on the availability of resources, their efficient or even industrially viable conversion processes, and replenishment time of feedstocks. Herein, we overview recent advances and developments in catalytic transformations of the carbohydrate content of lignocellulosic biomass to IPCs (i.e., ethanol, 3-hydroxypropionic acid, isoprene, succinic and levulinic acids, furfural, and 5-hydroxymethylfurfural). The mechanistic aspects, development of new catalysts, different efficiency indicators (yield and selectivity), and conversion conditions of their production are presented and compared. The potential biochemical production routes utilizing recently engineered microorganisms are reviewed, as well. The sustainability metrics that could be applied to the chemical industry (individual set of sustainability indicators, composite indices methods, material and energy flow analysis-based metrics, and ethanol equivalents) are also overviewed as well as an outlook is provided to highlight challenges and opportunities associated with this huge research area.

Heterobimetallic transition metal/rare earth metal bifunctional catalysis: a Cu/Sm/Schiff base complex for syn-selective catalytic asymmetric nitro-Mannich reaction.

Science.gov (United States)

Handa, Shinya; Gnanadesikan, Vijay; Matsunaga, Shigeki; Shibasaki, Masakatsu

2010-04-07

The full details of a catalytic asymmetric syn-selective nitro-Mannich reaction promoted by heterobimetallic Cu/Sm/dinucleating Schiff base complexes are described, demonstrating the effectiveness of the heterobimetallic transition metal/rare earth metal bifunctional catalysis. The first-generation system prepared from Cu(OAc)(2)/Sm(O-iPr)(3)/Schiff base 1a = 1:1:1 with an achiral phenol additive was partially successful for achieving the syn-selective catalytic asymmetric nitro-Mannich reaction. The substrate scope and limitations of the first-generation system remained problematic. After mechanistic studies on the catalyst prepared from Sm(O-iPr)(3), we reoptimized the catalyst preparation method, and a catalyst derived from Sm(5)O(O-iPr)(13) showed broader substrate generality as well as higher reactivity and stereoselectivity compared to Sm(O-iPr)(3). The optimal system with Sm(5)O(O-iPr)(13) was applicable to various aromatic, heteroaromatic, and isomerizable aliphatic N-Boc imines, giving products in 66-99% ee and syn/anti = >20:1-13:1. Catalytic asymmetric synthesis of nemonapride is also demonstrated using the catalyst derived from Sm(5)O(O-iPr)(13).

Effect of process parameters and injector position on the efficiency of NOx reduction by selective non catalytic reduction technique

International Nuclear Information System (INIS)

Hamid, A.; Mehmood, M.A.; Irfan, N.; Javed, M.T.; Waheed, K.

2009-01-01

An experimental investigation has been performed to study the effect of atomizer pressure dilution of the reducing reagent and the injector position on the efficiency or the NOx reduction by a selective non-catalytic reduction technique using urea as a reducing agent. Experiments were performed with a flow reactor in which flue gas was generated by the combustion of methane in air at stoichiometric amount of oxygen and the desired levels of initial NOx (400-450 ppm) were achieved by doping the flame with ammonia. The work was directed to investigate the effect of atomizer pressure, dilution of urea reagent and the injector position. The atomizer pressure was varied from 1 to 3bar and 20-25% increase in efficiency was observed by decreasing the pressure. Effect of dilution of urea solution was investigated by varying the strength of the solution from the 8 to 32% and 40-45% increase in the efficiency was observed. Effects of injector position was investigated by injecting the urea solution both in co current and counter current direction of the flue gases and 20-25% increase in the efficiency was observed in counter current direction. (author)

Arthroscopic partial meniscectomy in middle-aged patients with mild or no knee osteoarthritis

DEFF Research Database (Denmark)

Hare, Kristoffer B; Lohmander, Stefan; Christensen, Robin

2013-01-01

Arthroscopic partial meniscectomy has been shown to be of no benefit to patients with concomitant knee osteoarthritis, but the optimal treatment of a degenerative meniscus tear in patients with mild or no knee osteoarthritis is unknown. This article describes the rationale and methodology...... of a randomized sham-controlled trial to assess the benefit of arthroscopic partial meniscectomy of a medial meniscus tear in patients with mild or no knee osteoarthritis. The objective of the study is to test whether the benefit from arthroscopic partial meniscectomy in patients with knee pain, medial meniscus...... lesion and mild/no knee osteoarthritis, is greater after arthroscopic partial meniscectomy than following sham surgery....

A prospective randomized study of Chop versus Chop plus alpha-2B interferon in patients with intermediate and high grade non-Hodgkin's lymphoma: the International Oncology Study Group NHL1 Study .

Science.gov (United States)

Giles, F J; Shan, J; Advani, S H; Akan, H; Aydogdu, I; Aziz, Z; Azim, H A; Bapsy, P P; Buyukkececi, F; Chaimongkol, B; Chen, P M; Cheong, S K; Ferhanoglu, B; Hamza, R; Khalid, H M; Intragumtornchai, T; Kim, S W; Kim, S Y; Koc, H; Kumar, L; Kumar, R; Lei, K I; Lekhakula, A; Muthalib, A; Patel, M; Poovalingam, V P; Prayoonwiwat, W; Rana, F; Reksodiputro, A H; Ruff, P; Sagar, T G; Schwarer, A P; Song, H S; Suh, C W; Suharti, C; Supindiman, I; Tee, G Y; Thamprasit, T; Villalon, A H; Wickham, N R; Wong, J E; Yalcin, A; Jootar, S

2000-12-01

The addition of a brief alpha interferon regimen to each CHOP induction cycle, plus one year of alpha interferon thrice weekly maintenance therapy, has no early effect on response rates or survival in patients with Intermediate or High grade cell NHL. The CHOP (Cyclophosphamide, Adriamycin. Vincristine, Prednisone) regimen is the most widely used first-line therapy for patients with Intermediate or High Grade (IG/HG) non-Hodgkin's lymphoma (NHL). Alpha 2b interferon (INF) enhances response rates and improves survival in low-grade NHL. The International Oncology Study Group (IOSG) conducted a prospective randomized study comparing CHOP alone or combined with INF in patients with IG/HG-NHL. The primary study aim was to compare the objective response rates in these patient cohorts. Patients with a confirmed diagnosis of measurable NHL of International Working Formulation (IWF) groups D to H histology were randomized to receive CHOP alone or CHOP with 5Mu INF s.c. for 5 days on days 22 to 26 of each 28 day cycle with INF 5 million units (Mu) given three times per week subcutaneously for 52 weeks in those patients who responded to CHOP plus INF. The overall response rates were equivalent in both groups: CHOP alone (214 patients) 81% (complete 55%, partial 26%); CHOP plus INF (221 patients) 80% (complete 54%, partial 26%). At 36 months, the actuarial survival rate was equivalent in both groups. There is no apparent early advantage in terms of response or survival conferred by adding the study INF regimen to CHOP therapy for patients with IG/HG-NHL.

The area distribution of two-dimensional random walks and non-Hermitian Hofstadter quantum mechanics

International Nuclear Information System (INIS)

Matveenko, Sergey; Ouvry, Stéphane

2014-01-01

When random walks on a square lattice are biased horizontally to move solely to the right, the probability distribution of their algebraic area can be obtained exactly (Mashkevich and Ouvry 2009 J. Stat. Phys. 137 71). We explicitly map this biased classical random system onto a non-Hermitian Hofstadter-like quantum model where a charged particle on a square lattice coupled to a perpendicular magnetic field hops only to the right. For the commensurate case, when the magnetic flux per unit cell is rational, an exact solution of the quantum model is obtained. The periodicity of the lattice allows one to relate traces of the Nth power of the Hamiltonian to probability distribution generating functions of biased walks of length N. (paper)

The perioperative outcomes between renal hilar and non-hilar tumors following robotic-assisted partial nephrectomy (RAPN).

Science.gov (United States)

Lu, Shih-Yen; Chung, Hsiao-Jen; Huang, Eric Yi-Hsiu; Lin, Tzu-Pin; Lin, Alex T L

2018-03-15

The aim of this study was to compare the perioperative outcomes between renal hilar tumors and non-hilar tumors after robotic-assisted partial nephrectomy (RAPN). A retrospective review of consecutive patients who underwent RAPN from December 2009 to September 2015 at our institution was recruited. Perioperative outcomes including demographic characteristics, perioperative, pathological and renal function outcomes were compared between the hilar group (n = 30) and non-hilar group (n = 170). In characteristics, hilar group was younger (52.4 vs. 58 years, p = 0.04) and had less body mass index (23.7 vs. 25.4 kg/m 2 , p = 0.018). Hilar group had larger tumor size (4.8 vs. 3.7 cm, p = 0.009), higher Preoperative Aspects and Dimensions Used for an Anatomical (PADUA) score (10.7 vs. 8.5, p Hilar tumor was associated with longer operative time (293.6 vs. 240.5 min, p = 0.001) and warm ischemia time (39.9 vs. 21.8 min, p hilar tumor patients had no difference of the change of creatinine and estimated glomerular filtration rate (eGFR) at postoperative 6 and 12 month as compared with non-hilar tumor patients. For renal hilar tumor, RAPN could provide acceptable results of perioperative, pathological and renal function outcome as compared with non-hilar tumor group. Thus RAPN is a safe and effective nephron-sparing surgery technique for renal hilar tumors. Copyright © 2018. Published by Elsevier Taiwan LLC.

Cannabinoids for treatment of chronic non-cancer pain; a systematic review of randomized trials

OpenAIRE

Lynch, Mary E; Campbell, Fiona

2011-01-01

Effective therapeutic options for patients living with chronic pain are limited. The pain relieving effect of cannabinoids remains unclear. A systematic review of randomized controlled trials (RCTs) examining cannabinoids in the treatment of chronic non-cancer pain was conducted according to the PRISMA statement update on the QUORUM guidelines for reporting systematic reviews that evaluate health care interventions. Cannabinoids studied included smoked cannabis, oromucosal extracts of cannabi...

Novel Metal Nanomaterials and Their Catalytic Applications

Directory of Open Access Journals (Sweden)

Jiaqing Wang

2015-09-01

Full Text Available In the rapidly developing areas of nanotechnology, nano-scale materials as heterogeneous catalysts in the synthesis of organic molecules have gotten more and more attention. In this review, we will summarize the synthesis of several new types of noble metal nanostructures (FePt@Cu nanowires, Pt@Fe2O3 nanowires and bimetallic Pt@Ir nanocomplexes; Pt-Au heterostructures, Au-Pt bimetallic nanocomplexes and Pt/Pd bimetallic nanodendrites; Au nanowires, CuO@Ag nanowires and a series of Pd nanocatalysts and their new catalytic applications in our group, to establish heterogeneous catalytic system in “green” environments. Further study shows that these materials have a higher catalytic activity and selectivity than previously reported nanocrystal catalysts in organic reactions, or show a superior electro-catalytic activity for the oxidation of methanol. The whole process might have a great impact to resolve the energy crisis and the environmental crisis that were caused by traditional chemical engineering. Furthermore, we hope that this article will provide a reference point for the noble metal nanomaterials’ development that leads to new opportunities in nanocatalysis.

Catalytic Organic Transformations Mediated by Actinide Complexes

Directory of Open Access Journals (Sweden)

Isabell S. R. Karmel

2015-10-01

Full Text Available This review article presents the development of organoactinides and actinide coordination complexes as catalysts for homogeneous organic transformations. This chapter introduces the basic principles of actinide catalysis and deals with the historic development of actinide complexes in catalytic processes. The application of organoactinides in homogeneous catalysis is exemplified in the hydroelementation reactions, such as the hydroamination, hydrosilylation, hydroalkoxylation and hydrothiolation of alkynes. Additionally, the use of actinide coordination complexes for the catalytic polymerization of α-olefins and the ring opening polymerization of cyclic esters is presented. The last part of this review article highlights novel catalytic transformations mediated by actinide compounds and gives an outlook to the further potential of this field.

Modeling and simulation of heterogeneous catalytic processes

CERN Document Server

Dixon, Anthony

2014-01-01

Heterogeneous catalysis and mathematical modeling are essential components of the continuing search for better utilization of raw materials and energy, with reduced impact on the environment. Numerical modeling of chemical systems has progressed rapidly due to increases in computer power, and is used extensively for analysis, design and development of catalytic reactors and processes. This book presents reviews of the state-of-the-art in modeling of heterogeneous catalytic reactors and processes. Reviews by leading authorities in the respective areas Up-to-date reviews of latest techniques in modeling of catalytic processes Mix of US and European authors, as well as academic/industrial/research institute perspectives Connections between computation and experimental methods in some of the chapters.

Mass transfer model liquid phase catalytic exchange column simulation applicable to any column composition profile

Energy Technology Data Exchange (ETDEWEB)

Busigin, A. [NITEK USA Inc., Ocala, FL (United States)

2015-03-15

Liquid Phase Catalytic Exchange (LPCE) is a key technology used in water detritiation systems. Rigorous simulation of LPCE is complicated when a column may have both hydrogen and deuterium present in significant concentrations in different sections of the column. This paper presents a general mass transfer model for a homogenous packed bed LPCE column as a set of differential equations describing composition change, and equilibrium equations to define the mass transfer driving force within the column. The model is used to show the effect of deuterium buildup in the bottom of an LPCE column from non-negligible D atom fraction in the bottom feed gas to the column. These types of calculations are important in the design of CECE (Combined Electrolysis and Catalytic Exchange) water detritiation systems.

PARTIAL ERUPTION OF A FILAMENT WITH TWISTING NON-UNIFORM FIELDS

International Nuclear Information System (INIS)

Bi, Yi; Jiang, Yunchun; Yang, Jiayan; Xiang, Yongyuan; Cai, Yunfang; Liu, Weiwei

2015-01-01

The eruption of a filament in a kinklike fashion is often regarded as a signature of kink instability. However, the kink instability threshold for the filament’s magnetic structure is not widely understood. Using Hα observations from the New Vacuum Solar Telescope, we present a partial eruptive filament. During the eruption, the filament thread appeared to split from its middle and to break out in a kinklike fashion. In this period, the remaining filament material stayed below and erupted without the kinking motion later on. The coronal magnetic field lines associated with the filament are obtained from nonlinear force-free field extrapolations using the twelve-minute-cadence vector magnetograms of the Helioseismic and Magnetic Imager (HMI) on board the Solar Dynamic Observatory. We studied the extrapolated field lines passing through the magnetic dips which are in good agreement with the observed filament. The field lines are non-uniformly twisted and appear to be composed of two twisted flux ropes winding around each other. One of them has a higher twist than the other, and the flux rope with the higher twist has its dips aligned with the kinking eruptive thread at the beginning of its eruption. Before the eruption, moreover, the flux rope with the higher twist was found to expand with an approximately constant field twist. In addition, the helicity flux maps deduced from the HMI magnetograms show that some helicity is injected into the overlying magnetic arcade, but no significant helicity is injected into the flux ropes. Accordingly, we suggest that the highly twisted flux rope became kink unstable when the instability threshold declined with the expansion of the flux rope

Catalytic hydrogenation of carbon monoxide

International Nuclear Information System (INIS)

Wayland, B.B.

1993-12-01

Focus of this project is on developing new approaches for hydrogenation of carbon monoxide to produce organic oxygenates at mild conditions. The strategies to accomplish CO reduction are based on favorable thermodynamics manifested by rhodium macrocycles for producing a series of intermediates implicated in the catalytic hydrogenation of CO. Metalloformyl complexes from reactions of H 2 and CO, and CO reductive coupling to form metallo α-diketone species provide alternate routes to organic oxygenates that utilize these species as intermediates. Thermodynamic and kinetic-mechanistic studies are used in guiding the design of new metallospecies to improve the thermodynamic and kinetic factors for individual steps in the overall process. Electronic and steric effects associated with the ligand arrays along with the influences of the reaction medium provide the chemical tools for tuning these factors. Non-macrocyclic ligand complexes that emulate the favorable thermodynamic features associated with rhodium macrocycles, but that also manifest improved reaction kinetics are promising candidates for future development

Partially oxidized atomic cobalt layers for carbon dioxide electroreduction to liquid fuel

Science.gov (United States)

Gao, Shan; Lin, Yue; Jiao, Xingchen; Sun, Yongfu; Luo, Qiquan; Zhang, Wenhua; Li, Dianqi; Yang, Jinlong; Xie, Yi

2016-01-01

Electroreduction of CO2 into useful fuels, especially if driven by renewable energy, represents a potentially ‘clean’ strategy for replacing fossil feedstocks and dealing with increasing CO2 emissions and their adverse effects on climate. The critical bottleneck lies in activating CO2 into the CO2•- radical anion or other intermediates that can be converted further, as the activation usually requires impractically high overpotentials. Recently, electrocatalysts based on oxide-derived metal nanostructures have been shown to enable CO2 reduction at low overpotentials. However, it remains unclear how the electrocatalytic activity of these metals is influenced by their native oxides, mainly because microstructural features such as interfaces and defects influence CO2 reduction activity yet are difficult to control. To evaluate the role of the two different catalytic sites, here we fabricate two kinds of four-atom-thick layers: pure cobalt metal, and co-existing domains of cobalt metal and cobalt oxide. Cobalt mainly produces formate (HCOO-) during CO2 electroreduction; we find that surface cobalt atoms of the atomically thin layers have higher intrinsic activity and selectivity towards formate production, at lower overpotentials, than do surface cobalt atoms on bulk samples. Partial oxidation of the atomic layers further increases their intrinsic activity, allowing us to realize stable current densities of about 10 milliamperes per square centimetre over 40 hours, with approximately 90 per cent formate selectivity at an overpotential of only 0.24 volts, which outperforms previously reported metal or metal oxide electrodes evaluated under comparable conditions. The correct morphology and oxidation state can thus transform a material from one considered nearly non-catalytic for the CO2 electroreduction reaction into an active catalyst. These findings point to new opportunities for manipulating and improving the CO2 electroreduction properties of metal systems

Cyanogel-derived N-doped C nanosheets immobilizing Pd-P nanoparticles: One-pot synthesis and enhanced hydrogenation catalytic performance

Energy Technology Data Exchange (ETDEWEB)

Zhang, Hao; Yan, Xiaohong; Huang, Yundi; Zhang, Mengru; Tang, Yawen; Sun, Dongmei; Xu, Lin, E-mail: njuxulin@gmail.com; Wei, Shaohua, E-mail: weishaohua@njnu.edu.cn

2017-02-28

Highlights: • Cyanogel-bridged approach was developed for the synthesis of Pd-P@N-Cnanosheets. • Pd-P@N-C nanosheets exhibit high activity and stability for reduction of 4-NP. • Compositional and structural advantages account for the high catalytic activity. • The feasible synthesis could be extendable to other carbon-based nanohybrids. - Abstract: For Pd-based nanocatalysts, stabilization of Pd nanoparticles on carbon support could not only effectively avoid particle aggregation and maintain catalytic stability during catalytic processes, but also facilitate enhancing the catalytic activity due to the synergy between Pd nanoparticles and carbon support. Furthermore, the incorporation of non-metal of phosphorus (P) into Pd could effectively modulate the electronic structure of Pd and thus help to boost the catalytic properties. However, one-pot synthesis of such nanohybrids remains a great challenge due to the distinct physiochemical properties of Pd, P and C components. Herein, we demonstrate a one-pot and scalable synthesis of highly dispersed PdP alloy nanoparticle-immobilized on N-doped graphitic carbon nanosheets (abbreviated as Pd-P@N-C nanosheets) by using inorganic-organic hybrid cyanogel as a reaction precursor. In virtue of both compositional and structural advantages, the as-synthesized Pd-P@N-C nanosheets manifest a superior catalytic activity and stability toward the hydrogenation of 4-nitrophenol (4-NP). We believe that the present work will provide a feasible and versatile strategy for the development of efficient catalysts for environmental remediation and can also be extendable to other carbon-based nanohybrids with desirable functionalities.

Partially ordered sets, transfinite topology and the dimension of Cantorian-fractal spacetime

Energy Technology Data Exchange (ETDEWEB)

Marek-Crnjac, L. [Institute of Mathematics and Physics, University of Maribor (Slovenia)], E-mail: leila.marek@guest.arnes.si

2009-11-15

We introduce partially ordered sets and relate them to random Cantor sets of E-infinity theory. Subsequently we derive the dimensionality of Cantorian-fractal spacetime using posets and E-infinity transfinite Cantor sets.

Kinetic catalytic studies of scorpion's hemocyanin

International Nuclear Information System (INIS)

Queinnec, E.; Vuillaume, M.; Gardes-Albert, M.; Ferradini, C.; Ducancel, F.

1991-01-01

Hemocyanins are copper proteins which function as oxygen carriers in the haemolymph of Molluscs and Arthropods. They possess enzymatic properties: peroxidatic and catalatic activities, although they have neither iron nor porphyrin ring at the active site. The kinetics of the catalytic reaction is described. The reaction of superoxide anion with hemocyanin has been studied using pulse radiolysis at pH 9. The catalytic rate constant is 3.5 X 10 7 mol -1 .l.s -1 [fr

A Partial Backlogging Inventory Model for Deteriorating Item under Fuzzy Inflation and Discounting over Random Planning Horizon: A Fuzzy Genetic Algorithm Approach

Directory of Open Access Journals (Sweden)

Dipak Kumar Jana

2013-01-01

Full Text Available An inventory model for deteriorating item is considered in a random planning horizon under inflation and time value money. The model is described in two different environments: random and fuzzy random. The proposed model allows stock-dependent consumption rate and shortages with partial backlogging. In the fuzzy stochastic model, possibility chance constraints are used for defuzzification of imprecise expected total profit. Finally, genetic algorithm (GA and fuzzy simulation-based genetic algorithm (FSGA are used to make decisions for the above inventory models. The models are illustrated with some numerical data. Sensitivity analysis on expected profit function is also presented. Scope and Purpose. The traditional inventory model considers the ideal case in which depletion of inventory is caused by a constant demand rate. However, to keep sales higher, the inventory level would need to remain high. Of course, this would also result in higher holding or procurement cost. Also, in many real situations, during a longer-shortage period some of the customers may refuse the management. For instance, for fashionable commodities and high-tech products with short product life cycle, the willingness for a customer to wait for backlogging is diminishing with the length of the waiting time. Most of the classical inventory models did not take into account the effects of inflation and time value of money. But in the past, the economic situation of most of the countries has changed to such an extent due to large-scale inflation and consequent sharp decline in the purchasing power of money. So, it has not been possible to ignore the effects of inflation and time value of money any more. The purpose of this paper is to maximize the expected profit in the random planning horizon.

Superdiffusion in a non-Markovian random walk model with a Gaussian memory profile

Science.gov (United States)

Borges, G. M.; Ferreira, A. S.; da Silva, M. A. A.; Cressoni, J. C.; Viswanathan, G. M.; Mariz, A. M.

2012-09-01

Most superdiffusive Non-Markovian random walk models assume that correlations are maintained at all time scales, e.g., fractional Brownian motion, Lévy walks, the Elephant walk and Alzheimer walk models. In the latter two models the random walker can always "remember" the initial times near t = 0. Assuming jump size distributions with finite variance, the question naturally arises: is superdiffusion possible if the walker is unable to recall the initial times? We give a conclusive answer to this general question, by studying a non-Markovian model in which the walker's memory of the past is weighted by a Gaussian centered at time t/2, at which time the walker had one half the present age, and with a standard deviation σt which grows linearly as the walker ages. For large widths we find that the model behaves similarly to the Elephant model, but for small widths this Gaussian memory profile model behaves like the Alzheimer walk model. We also report that the phenomenon of amnestically induced persistence, known to occur in the Alzheimer walk model, arises in the Gaussian memory profile model. We conclude that memory of the initial times is not a necessary condition for generating (log-periodic) superdiffusion. We show that the phenomenon of amnestically induced persistence extends to the case of a Gaussian memory profile.

The Effects of the Bali Yoga Program for Breast Cancer Patients on Chemotherapy-Induced Nausea and Vomiting: Results of a Partially Randomized and Blinded Controlled Trial.

Science.gov (United States)

Anestin, Annélie S; Dupuis, Gilles; Lanctôt, Dominique; Bali, Madan

2017-10-01

Complementary and alternative medicine has been shown to be beneficial in reducing chemotherapy-induced nausea and vomiting. However, conclusive results are lacking in order to confirm its usefulness. The purpose of this study was to determine whether a standardized yoga intervention could reduce these adverse symptoms. This was a partially randomized and blinded controlled trial comparing a standardized yoga intervention with standard care. Eligible patients were adults diagnosed with stages I to III breast cancer receiving chemotherapy. Patients randomized to the experimental group participated in an 8-week yoga program. There was no significant difference between the experimental and control groups on chemotherapy-induced nausea and vomiting after 8 weeks. Results suggest the yoga program is not beneficial in managing these adverse symptoms. However, considering preliminary evidence suggesting yoga's beneficial impact in cancer symptom management, methodological limitations should be explored and additional studies should be conducted.

Tunable preparation of ruthenium nanoparticles with superior size-dependent catalytic hydrogenation properties

Energy Technology Data Exchange (ETDEWEB)

Zhao, Yuan; Luo, Yaodong; Yang, Xuan; Yang, Yaxin; Song, Qijun, E-mail: qsong@jiangnan.edu.cn

2017-06-15

Highlights: • A facile and efficient strategy is firstly developed for the synthesis of Ru NPs. • Ru NPs are stable and uniform with the controllable sizes from 2.6 to 51.5 nm. • Ru NPs exhibit size-dependent and superior catalytic hydrogenation activity. - Abstract: Ruthenium (Ru) featured with an unusual catalytic behavior is of great significance in several heterogeneous and electro-catalytic reactions. The preparation of tractable Ru nanocatalysts and the building of highly active catalytic system at ambient temperature remains a grand challenge. Herein, a facile strategy is developed for the controllable preparation of Ru nanoparticles (NPs) with the sizes ranging from 2.6 to 51.5 nm. Ru NPs show superior size-dependent catalytic performance with the best kinetic rate constant as high as −1.52 min{sup −1}, which could far surpass the other traditional noble metals. Ru NPs exert exceedingly efficient low-temperature catalytic activity and good recyclability in the catalytic reduction of nitroaromatic compounds (NACs) and azo dyes. The developed catalytic system provides a distinguishing insight for the artificial preparation of Ru NPs with desired sizes, and allows for the development of rational design rules for exploring catalysts with superior catalytic performances, potentially broadening the applications of metallic NP-enabled catalytic analysis.

Partially nested designs in psychotherapy trials: A review of modeling developments.

Science.gov (United States)

Sterba, Sonya K

2017-07-01

Individually-randomized psychotherapy trials are often partially nested. For instance, individuals assigned to a treatment arm may be clustered into therapy groups for purposes of treatment administration, whereas individuals assigned to a wait-list control are unclustered. The past several years have seen rapid expansion and investigation of methods for analyzing partially nested data. Yet partial nesting often remains ignored in psychotherapy trials. This review integrates and disseminates developments in the analysis of partially nested data that are particularly relevant for psychotherapy researchers. First, we differentiate among alternative partially nested designs. Then, we present adaptations of multilevel model specifications that accommodate each design. Next, we address how moderation by treatment as well as mediation of the treatment effect can be investigated in partially nested designs. Model fitting results, annotated software syntax, and illustrative data sets are provided and key methodological issues are discussed. We emphasize that cluster-level variability in the treatment arm need not be considered a nuisance; it can be modeled to yield insights about the treatment process.

Orion EFT-1 Catalytic Tile Experiment Overview and Flight Measurements

Science.gov (United States)

Salazar, Giovanni; Amar, Adam; Hyatt, Andrew; Rezin, Marc D.

2016-01-01

This paper describes the design and results of a surface catalysis flight experiment flown on the Orion Multipurpose Crew Vehicle during Exploration Flight Test 1 (EFT1). Similar to previous Space Shuttle catalytic tile experiments, the present test consisted of a highly catalytic coating applied to an instrumented TPS tile. However, the present catalytic tile experiment contained significantly more instrumentation in order to better resolve the heating overshoot caused by the change in surface catalytic efficiency at the interface between two distinct materials. In addition to collecting data with unprecedented spatial resolution of the "overshoot" phenomenon, the experiment was also designed to prove if such a catalytic overshoot would be seen in turbulent flow in high enthalpy regimes. A detailed discussion of the results obtained during EFT1 is presented, as well as the challenges associated with data interpretation of this experiment. Results of material testing carried out in support of this flight experiment are also shown. Finally, an inverse heat conduction technique is employed to reconstruct the flight environments at locations upstream and along the catalytic coating. The data and analysis presented in this work will greatly contribute to our understanding of the catalytic "overshoot" phenomenon, and have a significant impact on the design of future spacecraft.

The Mobility Enhancement of Indium Gallium Zinc Oxide Transistors via Low-temperature Crystallization using a Tantalum Catalytic Layer.

Science.gov (United States)

Shin, Yeonwoo; Kim, Sang Tae; Kim, Kuntae; Kim, Mi Young; Oh, Saeroonter; Jeong, Jae Kyeong

2017-09-07

High-mobility indium gallium zinc oxide (IGZO) thin-film transistors (TFTs) are achieved through low-temperature crystallization enabled via a reaction with a transition metal catalytic layer. For conventional amorphous IGZO TFTs, the active layer crystallizes at thermal annealing temperatures of 600 °C or higher, which is not suitable for displays using a glass substrate. The crystallization temperature is reduced when in contact with a Ta layer, where partial crystallization at the IGZO back-channel occurs with annealing at 300 °C, while complete crystallization of the active layer occurs at 400 °C. The field-effect mobility is significantly boosted to 54.0 cm 2 /V·s for the IGZO device with a metal-induced polycrystalline channel formed at 300 °C compared to 18.1 cm 2 /V·s for an amorphous IGZO TFT without a catalytic layer. This work proposes a facile and effective route to enhance device performance by crystallizing the IGZO layer with standard annealing temperatures, without the introduction of expensive laser irradiation processes.

Radioguided occult lesion localization versus wire-guided localization for non-palpable breast lesions: randomized controlled trial

International Nuclear Information System (INIS)

Ocal, Koray; Dag, Ahmet; Turkmenoglu, Ozgur; Yucel, Erdem; Gunay, Emel Ceylan; Duce, Meltem Nass

2011-01-01

Aim: this prospective randomized clinical study was conducted to compare radioguided occult lesion localization (ROLL) with wire-guided localization to evaluate optimum localization techniques for non-palpable breast lesions. Methods: a total of 108 patients who were undergoing an excisional biopsy for non-palpable breast lesions requiring pathologic diagnosis were randomly assigned to the ROLL group (n 56) and wire-guided localization group (n 52). In the study, patients' characteristics, radiological abnormalities, radiological technique of localization, localization time, operation time, weight of the excised specimen, clearance margins, pathological diagnosis and perioperative complications were assessed. Results: there were no differences between the two groups in terms of age, radiological abnormalities and localization technique (p = non-significant for all). ROLL techniques resulted in 100% retrieval of the lesions; for the wire-guided localization technique, 98%. Both localization time and operation time were significantly reduced with the ROLL technique (p = significant for all). The weight of the specimen was significantly lower in the ROLL group than in the wire-guided localization group (p = significant). The overall complication rate and pathological diagnosis were similar for both groups (p = non-significant for all). Clear margins were achieved in 91% of ROLL patients and in 53% of wire-guided localization patients, and the difference was significant. Conclusions: the present study indicated that the ROLL technique is as effective as wire-guided localization for the excision of non-palpable breast lesions. In addition, ROLL improved the outcomes by reducing localization and operation time, preventing healthy tissue excision and achieving clearer margins. (author)

Radioguided occult lesion localization versus wire-guided localization for non-palpable breast lesions: randomized controlled trial

Energy Technology Data Exchange (ETDEWEB)

Ocal, Koray; Dag, Ahmet; Turkmenoglu, Ozgur; Yucel, Erdem [Mersin University (Turkey). Medical Faculty. Dept. of General Surgery; Gunay, Emel Ceylan [Mersin University (Turkey). Medical Faculty. Dept. of Nuclear Medicine; Duce, Meltem Nass [Mersin University (Turkey). Medical Faculty. Dept. of Radiology

2011-07-01

Aim: this prospective randomized clinical study was conducted to compare radioguided occult lesion localization (ROLL) with wire-guided localization to evaluate optimum localization techniques for non-palpable breast lesions. Methods: a total of 108 patients who were undergoing an excisional biopsy for non-palpable breast lesions requiring pathologic diagnosis were randomly assigned to the ROLL group (n 56) and wire-guided localization group (n 52). In the study, patients' characteristics, radiological abnormalities, radiological technique of localization, localization time, operation time, weight of the excised specimen, clearance margins, pathological diagnosis and perioperative complications were assessed. Results: there were no differences between the two groups in terms of age, radiological abnormalities and localization technique (p = non-significant for all). ROLL techniques resulted in 100% retrieval of the lesions; for the wire-guided localization technique, 98%. Both localization time and operation time were significantly reduced with the ROLL technique (p = significant for all). The weight of the specimen was significantly lower in the ROLL group than in the wire-guided localization group (p = significant). The overall complication rate and pathological diagnosis were similar for both groups (p = non-significant for all). Clear margins were achieved in 91% of ROLL patients and in 53% of wire-guided localization patients, and the difference was significant. Conclusions: the present study indicated that the ROLL technique is as effective as wire-guided localization for the excision of non-palpable breast lesions. In addition, ROLL improved the outcomes by reducing localization and operation time, preventing healthy tissue excision and achieving clearer margins. (author)

Heterogeneous catalytic degradation of polyacrylamide solution | Hu ...

African Journals Online (AJOL)

Modified with trace metal elements, the catalytic activity of Fe2O3/Al2O3 could be changed greatly. Among various trace metal elements, Fe2O3/Al2O3 catalysts modified with Co and Cu showed great increase on catalytic activity. International Journal of Engineering, Science and Technology, Vol. 2, No. 7, 2010, pp. 110- ...

Ce-Fe-O mixed oxide as oxygen carrier for the direct partial oxidation of methane to syngas

Institute of Scientific and Technical Information of China (English)

魏永刚; 王华; 李孔斋

2010-01-01

The Ce-Fe-O mixed oxide with a ratio of Ce/Fe=7:3, which was prepared by coprecipitation method and employed as oxygen carrier, for direct partial oxidation of methane to syngas in the absence of gaseous oxygen was explored. The mixed oxide was characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM), and the catalytic performances were studied in a fixed-bed quartz reactor and a thermogravimetric reactor, respectively. Approximately 99.4% H2 se...

Molecular beam mass spectrometer equipped with a catalytic wall reactor for in situ studies in high temperature catalysis research

International Nuclear Information System (INIS)

Horn, R.; Ihmann, K.; Ihmann, J.; Jentoft, F.C.; Geske, M.; Taha, A.; Pelzer, K.; Schloegl, R.

2006-01-01

A newly developed apparatus combining a molecular beam mass spectrometer and a catalytic wall reactor is described. The setup has been developed for in situ studies of high temperature catalytic reactions (>1000 deg. C), which involve besides surface reactions also gas phase reactions in their mechanism. The goal is to identify gas phase radicals by threshold ionization. A tubular reactor, made from the catalytic material, is positioned in a vacuum chamber. Expansion of the gas through a 100 μm sampling orifice in the reactor wall into differentially pumped nozzle, skimmer, and collimator chambers leads to the formation of a molecular beam. A quadrupole mass spectrometer with electron impact ion source designed for molecular beam inlet and threshold ionization measurements is used as the analyzer. The sampling time from nozzle to detector is estimated to be less than 10 ms. A detection time resolution of up to 20 ms can be reached. The temperature of the reactor is measured by pyrometry. Besides a detailed description of the setup components and the physical background of the method, this article presents measurements showing the performance of the apparatus. After deriving the shape and width of the energy spread of the ionizing electrons from measurements on N 2 and He we estimated the detection limit in threshold ionization measurements using binary mixtures of CO in N 2 to be in the range of several hundreds of ppm. Mass spectra and threshold ionization measurements recorded during catalytic partial oxidation of methane at 1250 deg. C on a Pt catalyst are presented. The detection of CH 3 · radicals is successfully demonstrated

Molecular beam mass spectrometer equipped with a catalytic wall reactor for in situ studies in high temperature catalysis research

Science.gov (United States)

Horn, R.; Ihmann, K.; Ihmann, J.; Jentoft, F. C.; Geske, M.; Taha, A.; Pelzer, K.; Schlögl, R.

2006-05-01

A newly developed apparatus combining a molecular beam mass spectrometer and a catalytic wall reactor is described. The setup has been developed for in situ studies of high temperature catalytic reactions (>1000°C), which involve besides surface reactions also gas phase reactions in their mechanism. The goal is to identify gas phase radicals by threshold ionization. A tubular reactor, made from the catalytic material, is positioned in a vacuum chamber. Expansion of the gas through a 100μm sampling orifice in the reactor wall into differentially pumped nozzle, skimmer, and collimator chambers leads to the formation of a molecular beam. A quadrupole mass spectrometer with electron impact ion source designed for molecular beam inlet and threshold ionization measurements is used as the analyzer. The sampling time from nozzle to detector is estimated to be less than 10ms. A detection time resolution of up to 20ms can be reached. The temperature of the reactor is measured by pyrometry. Besides a detailed description of the setup components and the physical background of the method, this article presents measurements showing the performance of the apparatus. After deriving the shape and width of the energy spread of the ionizing electrons from measurements on N2 and He we estimated the detection limit in threshold ionization measurements using binary mixtures of CO in N2 to be in the range of several hundreds of ppm. Mass spectra and threshold ionization measurements recorded during catalytic partial oxidation of methane at 1250°C on a Pt catalyst are presented. The detection of CH3• radicals is successfully demonstrated.

SHORT COMMUNICATION CATALYTIC KINETIC ...

African Journals Online (AJOL)

IV) catalyzes the discoloring reaction of DBS-arsenazo oxidized by potassium bromate, a new catalytic kinetic spectrophotometric method for the determination of trace titanium (IV) was developed. The linear range of the determination of ...

Catalytic Kinetic Resolution of Biaryl Compounds.

Science.gov (United States)

Ma, Gaoyuan; Sibi, Mukund P

2015-08-10

Biaryl compounds with axial chirality are very common in synthetic chemistry, especially in catalysis. Axially chiral biaryls are important due to their biological activities and extensive applications in asymmetric catalysis. Thus the development of efficient enantioselective methods for their synthesis has attracted considerable attention. This Minireview discusses the progress made in catalytic kinetic resolution of biaryl compounds and chronicles significant advances made recently in catalytic kinetic resolution of biaryl scaffolds. © 2015 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim.

synthesis, characterization, electrical and catalytic studies of some

African Journals Online (AJOL)

B. S. Chandravanshi

catalytic activity of the VO(IV) and Mn(III) complexes have been tested in the epoxidation reaction of styrene ... Vanadyl sulfate pentahydrate, chromium chloride hexahydrate, anhydrous ferric ..... The catalytic oxidation of styrene gives the products styrene oxide, benzaldehyde, benzoic acid, ... bond via a radical mechanism.

A Correlated Random Effects Model for Non-homogeneous Markov Processes with Nonignorable Missingness.

Science.gov (United States)

Chen, Baojiang; Zhou, Xiao-Hua

2013-05-01

Life history data arising in clusters with prespecified assessment time points for patients often feature incomplete data since patients may choose to visit the clinic based on their needs. Markov process models provide a useful tool describing disease progression for life history data. The literature mainly focuses on time homogeneous process. In this paper we develop methods to deal with non-homogeneous Markov process with incomplete clustered life history data. A correlated random effects model is developed to deal with the nonignorable missingness, and a time transformation is employed to address the non-homogeneity in the transition model. Maximum likelihood estimate based on the Monte-Carlo EM algorithm is advocated for parameter estimation. Simulation studies demonstrate that the proposed method works well in many situations. We also apply this method to an Alzheimer's disease study.

CIRCUIT IMPLEMENTATION OF VHDL-DESCRIPTIONS OF SYSTEMS OF PARTIAL BOOLEAN FUNCTIONS

Directory of Open Access Journals (Sweden)

P. N. Bibilo

2016-01-01

Full Text Available Method for description of incompletely specified (partial Boolean functions in VHDL is proposed. Examples of synthesized VHDL models of partial Boolean functions are presented; and the results of experiments on circuit implementation of VHDL descriptions of systems of partial functions. The realizability of original partial functions in logical circuits was verified by formal verification. The results of the experiments show that the preliminary minimization in DNF class and in the class of BDD representations for pseudo-random systems of completely specified functions does not improve practically (and in the case of BDD sometimes worsens the results of the subsequent synthesis in the basis of FPGA unlike the significant efficiency of these procedures for the synthesis of benchmark circuits taken from the practice of the design.

Efficacy and safety of extended-release oxcarbazepine (Oxtellar XR™) as adjunctive therapy in patients with refractory partial-onset seizures: a randomized controlled trial

Science.gov (United States)

French, JA; Baroldi, P; Brittain, ST; Johnson, JK

2014-01-01

Objective To evaluate the efficacy, tolerability, and safety of once-daily 1200 mg and 2400 mg SPN-804 (Oxtellar XR™, Supernus Pharmaceuticals), an extended-release tablet formulation of oxcarbazepine (OXC), added to 1-3 concomitant antiepileptic drugs (AEDs) in adults with refractory partial-onset seizures, with or without secondary generalization. Methods The Prospective, Randomized Study of OXC XR in Subjects with Partial Epilepsy Refractory (PROSPER) study was a multinational, randomized, double-blind, parallel-group Phase 3 study. The primary efficacy endpoint was median percent reduction from baseline in monthly (28-day) seizure frequency for the 16-week double-blind treatment period in the intent-to-treat (ITT) population with analyzable seizure data. Other efficacy analyses included proportion of patients with ≥ 50% seizure reduction, proportion of patients seizure free, and the relationship between clinical response and plasma concentration. Results Median percent reduction was -28.7% for placebo, −38.2% (P = 0.08 vs placebo) for once-daily SPN-804 1200 mg, and −42.9% (P = 0.003) for SPN-804 2400 mg. Responder rates were 28.1%, 36.1% (P = 0.08), and 40.7% (P = 0.02); 16-week seizure-free rates in a pragmatic ITT analysis were 3.3%, 4.9% (P = 0.59), and 11.4% (P = 0.008), respectively. When data were analyzed separately for study site clusters, a post hoc analysis demonstrated that both SPN-804 dosages were significantly superior to placebo in median percent seizure reduction (placebo: −13.3%; 1200 mg: −34.5%, P = 0.02; 2400 mg: −52.7%, P = 0.006) in the North American study site cluster. A concentration–response analysis also supported a clinically meaningful effect for 1200 mg. Adverse event types reflected the drug's established profile. Adverse event frequency was consistent with a pharmacokinetic profile in which SPN-804 produces lower peak plasma concentrations vs immediate-release OXC. Once-daily dosing was not

Non-Gaussian Stochastic Radiation Transfer in Finite Planar Media with Quadratic Scattering

International Nuclear Information System (INIS)

Sallah, M.

2016-01-01

The stochastic radiation transfer is considered in a participating planar finite continuously fluctuating medium characterized by non-Gaussian variability. The problem is considered for diffuse-reflecting boundaries with quadratic Rayleigh scattering. Random variable transformation (RVT) technique is used to get the complete average for the solution functions that are represented by the probability-density function (PDF) of the solution process. RVT algorithm applies a simple integral transformation to the input stochastic process (the extinction function of the medium). This linear transformation enables us to rewrite the stochastic transport equations in terms of the optical random variable (x) and the optical random thickness (L). Then the radiation transfer equation is solved deterministically to get a closed form for the solution as a function of x and L. So, the solution is used to obtain the PDF of the solution functions applying the RVT technique among the input random variable (L) and the output process (the solution functions). The obtained averages of the solution functions are used to get the complete analytical averages for some interesting physical quantities, namely, reflectivity, transmissivity and partial heat fluxes at the medium boundaries. Numerical results are represented graphically for different non-Gaussian probability distribution functions that compared with the corresponding Gaussian PDF.

Non-conformable, partial and conformable transposition

DEFF Research Database (Denmark)

König, Thomas; Mäder, Lars Kai

2013-01-01

and the Commission regarding a directive’s outcome, play a much more strategic role than has to date acknowledged in the transposition literature. Whereas disagreement of a member state delays conformable transposition, it speeds up non-conformable transposition. Disagreement of the Commission only prolongs...... the transposition process. We therefore conclude that a stronger focus on an effective sanctioning mechanism is warranted for safeguarding compliance with directives....

A novel tumor suppressor function of glycine N-methyltransferase is independent of its catalytic activity but requires nuclear localization.

Directory of Open Access Journals (Sweden)

Suchandra DebRoy

Full Text Available Glycine N-methyltransferase (GNMT, an abundant cytosolic enzyme, catalyzes the transfer of a methyl group from S-adenosylmethionine (SAM to glycine generating S-adenosylhomocysteine and sarcosine (N-methylglycine. This reaction is regulated by 5-methyltetrahydrofolate, which inhibits the enzyme catalysis. In the present study, we observed that GNMT is strongly down regulated in human cancers and is undetectable in cancer cell lines while the transient expression of the protein in cancer cells induces apoptosis and results in the activation of ERK1/2 as an early pro-survival response. The antiproliferative effect of GNMT can be partially reversed by treatment with the pan-caspase inhibitor zVAD-fmk but not by supplementation with high folate or SAM. GNMT exerts the suppressor effect primarily in cells originated from malignant tumors: transformed cell line of non-cancer origin, HEK293, was insensitive to GNMT. Of note, high levels of GNMT, detected in regenerating liver and in NIH3T3 mouse fibroblasts, do not produce cytotoxic effects. Importantly, GNMT, a predominantly cytoplasmic protein, was translocated into nuclei upon transfection of cancer cells. The presence of GNMT in the nuclei was also observed in normal human tissues by immunohistochemical staining. We further demonstrated that the induction of apoptosis is associated with the GNMT nuclear localization but is independent of its catalytic activity or folate binding. GNMT targeted to nuclei, through the fusion with nuclear localization signal, still exerts strong antiproliferative effects while its restriction to cytoplasm, through the fusion with nuclear export signal, prevents these effects (in each case the protein was excluded from cytosol or nuclei, respectively. Overall, our study indicates that GNMT has a secondary function, as a regulator of cellular proliferation, which is independent of its catalytic role.

Comparison of effectiveness of electrocautery and phenol application in partial matricectomy after partial nail extraction in the treatment of ingrown nails.

Science.gov (United States)

Misiak, Piotr; Terlecki, Artur; Rzepkowska-Misiak, Beata; Wcisło, Szymon; Brocki, Marian

2014-02-01

Ingrowing nail also known as onychocryptosis is a common health problem. This disease mostly affects young people, often carrying a considerable amount of socio-economic implications. It's foot problem that usually manifests as inflammation of tissue along the side of a toenail. The aim of the study was to asses and to compare effectiveness of electrocautery and phenol application in partial matrixectomy after partial nail extraction in the treatment of ingrown toenails. The group of 60 patients with ingrowing toenail which was randomized into two groups underwent partial matrixectomy in surgical outpatient clinic between 2009-2013. This group of patients was under surgical observation for 100 days in outpatient clinic. In all operated patients we obtained surgical success however we had 13 recurrences during the follow up period, 5 in the phenolization group and 8 in the electrocoagulation group. There was statistically significant difference between these two techniques, which indicated that matrix phenolization is connected with shortened healing time vs the matrix electrocoagulation.

Non-destructive Testing by Infrared Thermography Under Random Excitation and ARMA Analysis

Science.gov (United States)

Bodnar, J. L.; Nicolas, J. L.; Candoré, J. C.; Detalle, V.

2012-11-01

Photothermal thermography is a non-destructive testing (NDT) method, which has many applications in the field of control and characterization of thin materials. This technique is usually implemented under CW or flash excitation. Such excitations are not adapted for control of fragile materials or for multi-frequency analysis. To allow these analyses, in this article, the use of a new control mode is proposed: infrared thermography under random excitation and auto regressive moving average analysis. First, the principle of this NDT method is presented. Then, the method is shown to permit detection, with low energy constraints, of detachments situated in mural paintings.

Expediting the chemistry of hematite nanocatalyst for catalytic aquathermolysis of heavy crude oil

Science.gov (United States)

Khalil, Munawar

In upstream exploration and production of heavy and extra heavy oil, catalytic aquathermolysis is a process where steam (along with catalyst) is injected into the reservoir to improve oil production. The improvement of oil production has been associated with the reduction of heavy oil's viscosity due to the degradation of large hydrocarbon molecules (resin and asphaltene fractions) which mostly the result of desulphurization of organosulphur compounds. In this work, the potential of hematite (alpha-Fe2O3) nanoparticles, a nontoxic, inexpensive and the most stable phase of iron oxide, was investigated for aquathermolysis application. This dissertation encompasses the synthesis, surface modification, catalytic activity, and catalysis mechanism of hematite nanoparticles in aquathermolysis. In the first part of this study, a simple hydrothermal method was successfully developed to synthesize hematite nanoparticles with high purity and good crystallinity. Using this method, the size, crystal's growth rate, shape, and dispersity of the nanoparticles can be controlled by the amount of iron precursor, precipitation agent, temperature and reaction time. Furthermore, the surface chemistry of hematite nanoparticle was modified in order to improve particle dispersibility in hydrocarbon phase. Based on the result, oleic acid (OA) was successfully grafted on the surface of hematite nanoparticles by forming a monodentate interaction and changed the surface property of the nanoparticles from hydrophilic to hydrophobic. As the result, nanoparticles were able to be transferred from aqueous phase to non-polar phase, vice versa, depending on the amount of oleic acid used for modification. In the third part of this work, the catalytic activity and catalytic mechanism of hematite nanoparticles to catalyze desulphurization reaction were studied. It is found that hematite nanoparticles have a good catalytic activity to decompose a highly stable aromatic organosulphur compound, i

CATALYTIC KINETIC SPECTROPHOTOMETRIC DETERMINATION ...

African Journals Online (AJOL)

Preferred Customer

acetylchlorophosphonazo(CPApA) by hydrogen peroxide in 0.10 M phosphoric acid. A novel catalytic kinetic-spectrophotometric method is proposed for the determination of copper based on this principle. Copper(II) can be determined spectrophotometrically ...

Effectiveness of add-on therapy with domperidone vs alginic acid in proton pump inhibitor partial response gastro-oesophageal reflux disease in systemic sclerosis: randomized placebo-controlled trial.

Science.gov (United States)

Foocharoen, Chingching; Chunlertrith, Kitti; Mairiang, Pisaln; Mahakkanukrauh, Ajanee; Suwannaroj, Siraphop; Namvijit, Suwassa; Wantha, Orathai; Nanagara, Ratanavadee

2017-02-01

Twice-daily dosing of proton pump inhibitor (PPI), the standard therapy for gastro-oesophageal reflux disease (GERD), is an effective therapy for GERD in SSc. The aim of this study was to compare the efficacy of omeprazole in combination with domperidone vs in combination with algycon in reducing the severity and frequency of reflux symptoms of PPI partial response (PPI-PR) GERD in SSc. Adult SSc patients having PPI-PR GERD were randomly assigned to receive domperidone plus algycon placebo or algycon plus domperidone placebo in a 1:1 ratio plus omeprazole for 4 weeks. The assessment included severity of symptom grading by visual analogue scale, frequency of symptoms by frequency scale for symptoms of GERD and quality of life (QoL) by EuroQol five-dimensions questionnaire scoring. One hundred and forty-eight SSc-GERD patients were enrolled, of whom 88 had PPI-PR. Eighty cases were randomized for either domperidone (n = 38) or algycon (n = 37) therapy. The majority in both groups had the diffuse SSc subset. At the end of the study, no significant difference in symptom grading was found between groups. After treatment and compared with baseline, the severity of symptoms, frequency scale for symptoms of GERD and QoL significantly improved in both groups. Five (13.2%) and 8 (21.6%) respective cases in the domperidone and algycon groups did not respond. The prevalence of PPI-PR GERD is common. Domperidone and algycon are equally effective treatments in combination with omeprazole. However, ∼17% of patients were non-responsive, so the effectiveness of domperidone, algycon and PPI combination therapy should be further investigated. https://clinicaltrials.gov (NCT01878526). © The Author 2016. Published by Oxford University Press on behalf of the British Society for Rheumatology. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

The decomposition of mixed oxide Ag2Cu2O3: Structural features and the catalytic properties in CO and C2H4 oxidation

Science.gov (United States)

Svintsitskiy, Dmitry A.; Kardash, Tatyana Yu.; Slavinskaya, Elena M.; Stonkus, Olga A.; Koscheev, Sergei V.; Boronin, Andrei I.

2018-01-01

The mixed silver-copper oxide Ag2Cu2O3 with a paramelaconite crystal structure is a promising material for catalytic applications. The as-prepared sample of Ag2Cu2O3 consisted of brick-like particles extended along the [001] direction. A combination of physicochemical techniques such as TEM, XPS and XRD was applied to investigate the structural features of this mixed silver-copper oxide. The thermal stability of Ag2Cu2O3 was investigated using in situ XRD under different reaction conditions, including a catalytic CO + O2 mixture. The first step of Ag2Cu2O3 decomposition was accompanied by the appearance of ensembles consisting of silver nanoparticles with sizes of 5-15 nm. Silver nanoparticles were strongly oriented to each other and to the surface of the initial Ag2Cu2O3 bricks. Based on the XRD data, it was shown that the release of silver occurred along the a and b axes of the paramelaconite structure. Partial decomposition of Ag2Cu2O3 accompanied by the formation of silver nanoparticles was observed during prolonged air storage under ambient conditions. The high reactivity is discussed as a reason for spontaneous decomposition during Ag2Cu2O3 storage. The full decomposition of the mixed oxide into metallic silver and copper (II) oxide took place at temperatures higher than 300 °C regardless of the nature of the reaction medium (helium, air, CO + O2). Catalytic properties of partially and fully decomposed samples of mixed silver-copper oxide were measured in low-temperature CO oxidation and C2H4 epoxidation reactions.

Production of phenolic-rich bio-oil from catalytic fast pyrolysis of biomass using magnetic solid base catalyst

International Nuclear Information System (INIS)

Zhang, Zhi-bo; Lu, Qiang; Ye, Xiao-ning; Li, Wen-tao; Hu, Bin; Dong, Chang-qing

2015-01-01

Highlights: • Phenolic-rich bio-oil was selectively produced from catalytic fast pyrolysis of biomass using magnetic solid base catalyst. • The actual yield of twelve major phenolic compounds reached 43.9 mg/g. • The peak area% of all phenolics reached 68.5% at the catalyst-to-biomass ratio of 7. • The potassium phosphate/ferroferric oxide catalyst possessed promising recycling properties. - Abstract: A magnetic solid base catalyst (potassium phosphate/ferroferric oxide) was prepared and used for catalytic fast pyrolysis of poplar wood to selectively produce phenolic-rich bio-oil. Pyrolysis–gas chromatography/mass spectrometry experiments were conducted to investigate the effects of pyrolysis temperature and catalyst-to-biomass ratio on the product distribution. The actual yields of important pyrolytic products were quantitatively determined by the external standard method. Moreover, recycling experiments were performed to determine the re-utilization abilities of the catalyst. The results showed that the catalyst exhibited promising activity to selectively produce phenolic-rich bio-oil, due to its capability of promoting the decomposition of lignin to generate phenolic compounds and meanwhile inhibiting the devolatilization of holocellulose. The maximal phenolic yield was obtained at the pyrolysis temperature of 400 °C and catalyst-to-biomass ratio of 2. The concentration of the phenolic compounds increased monotonically along with the increasing of the catalyst-to-biomass ratio, with the peak area% value increasing from 28.1% in the non-catalytic process to as high as 68.5% at the catalyst-to-biomass ratio of 7. The maximal total actual yield of twelve quantified major phenolic compounds was 43.9 mg/g, compared with the value of 29.0 mg/g in the non-catalytic process. In addition, the catalyst could be easily recovered and possessed promising recycling properties.

Supported rhodium catalysts for ammonia-borane hydrolysis. Dependence of the catalytic activity on the highest occupied state of the single rhodium atoms

Energy Technology Data Exchange (ETDEWEB)

Wang, Liangbing; Li, Hongliang; Zhang, Wenbo; Zhao, Xiao; Qiu, Jianxiang; Li, Aowen; Zheng, Xusheng; Zeng, Jie [Hefei National Lab. for Physical Sciences at the Microscale, Key Lab. of Strongly-Coupled Quantum Matter Physics, Chinese Academy of Sciences, Hefei, Anhui(China); Department of Chemical Physics, University of Science and Technology of China, Hefei, Anhui (China); Hu, Zhenpeng [School of Physics, Nankai University, Tianjin (China); Si, Rui [Shanghai Synchrotron Radiation Facility, Shanghai Institute of Applied Physics, Chinese Academy of Sciences (China)

2017-04-18

Supported metal nanocrystals have exhibited remarkable catalytic performance in hydrogen generation reactions, which is influenced and even determined by their supports. Accordingly, it is of fundamental importance to determine the direct relationship between catalytic performance and metal-support interactions. Herein, we provide a quantitative profile for exploring metal-support interactions by considering the highest occupied state in single-atom catalysts. The catalyst studied consisted of isolated Rh atoms dispersed on the surface of VO{sub 2} nanorods. It was observed that the activation energy of ammonia-borane hydrolysis changed when the substrate underwent a phase transition. Mechanistic studies indicate that the catalytic performance depended directly on the highest occupied state of the single Rh atoms, which was determined by the band structure of the substrates. Other metal catalysts, even with non-noble metals, that exhibited significant catalytic activity towards NH{sub 3}BH{sub 3} hydrolysis were rationally designed by adjusting their highest occupied states. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Partial correlation matrix estimation using ridge penalty followed by thresholding and re-estimation.

Science.gov (United States)

Ha, Min Jin; Sun, Wei

2014-09-01

Motivated by the problem of construction of gene co-expression network, we propose a statistical framework for estimating high-dimensional partial correlation matrix by a three-step approach. We first obtain a penalized estimate of a partial correlation matrix using ridge penalty. Next we select the non-zero entries of the partial correlation matrix by hypothesis testing. Finally we re-estimate the partial correlation coefficients at these non-zero entries. In the second step, the null distribution of the test statistics derived from penalized partial correlation estimates has not been established. We address this challenge by estimating the null distribution from the empirical distribution of the test statistics of all the penalized partial correlation estimates. Extensive simulation studies demonstrate the good performance of our method. Application on a yeast cell cycle gene expression data shows that our method delivers better predictions of the protein-protein interactions than the Graphic Lasso. © 2014, The International Biometric Society.

Destruction of organochlorated compounds and CFCs by catalytic hydrodechloration; Destruccion de compuestos organoclorados y CFCs mediante hidrodecloracion catalitica

Energy Technology Data Exchange (ETDEWEB)

Ordonez Garcia, S.; Sastre Andres, H.; Diez Sanz, F. V.

1998-12-01

The destruction of organohalogenated compounds ( for example chlorinated solvents, PCBs and CFCs) is a very serious environmental problems. Catalytic hydrodechlorination has shown to be potentially efficient method for the destruction of these compounds. In this technique the halogenated compound reacts with hydrogen, tielding a non-chlorinated compound (environmentally harmless) and hydrogen-chloride. In this article, different set-ups and catalysts employed in the catalytic hydrogechlorination were described. Finally, some applications of this technique to the treatment of industrial effluents, such as the destruction of chlorinated solvents (as trichloroethylene o tetrachloromethane), conversion of CFCs into HCFCs, destruction of PCBs and treatment of water polluted with chlorinated pesticides. (Author) 28 refs.

Targeting health subsidies through a non-price mechanism: A randomized controlled trial in Kenya

Science.gov (United States)

Dupas, Pascaline; Hoffmann, Vivian; Kremer, Michael; Zwane, Alix Peterson

2016-01-01

Free provision of preventive health products can dramatically increase access in low income countries. A cost concern about free provision is that some recipients may not use the product, wasting resources (over-inclusion). Yet charging a price to screen out non-users may screen out poor people who need and would use the product (over-exclusion). We report on a randomized controlled trial of a screening mechanism that combines the free provision of chlorine solution for water treatment with a small non-monetary cost (household vouchers that need to be redeemed monthly in order). Relative to a non-voucher free distribution program, this mechanism reduces the quantity of chlorine procured by 60 percentage points, but reduces the share of households whose stored water tests positive for chlorine residual by only one percentage point, dramatically improving the tradeoff between over-inclusion and over-exclusion. PMID:27563091

Catalytic and thermal cracking processes of waste cooking oil for bio-gasoline synthesis

Science.gov (United States)

Dewanto, Muhammad Andry Rizki; Januartrika, Aulia Azka; Dewajani, Heny; Budiman, Arief

2017-03-01

Non-renewable energy resources such as fossil fuels, and coal were depleted as the increase of global energy demand. Moreover, environmental aspect becomes a major concern which recommends people to utilize bio-based resources. Waste cooking oil is one of the economical sources for biofuel production and become the most used raw material for biodiesel production. However, the products formed during frying, can affect the trans-esterification reaction and the biodiesel properties. Therefore, it needs to convert low-quality cooking oil directly into biofuel by both thermal and catalytic cracking processes. Thermal and catalytic cracking sometimes are regarded as prospective bio-energy conversion processes. This research was carried out in the packed bed reactor equipped with 2 stages preheater with temperature of reactor was variated in the range of 450-550°C. At the same temperature, catalytic cracking had been involved in this experiment, using activated ZSM-5 catalyst with 1 cm in length. The organic liquid product was recovered by three stages of double pipe condensers. The composition of cracking products were analyzed using GC-MS instrument and the caloric contents were analyzed using Bomb calorimeter. The results reveal that ZSM-5 was highly selective toward aromatic and long aliphatic compounds formation. The percentage recovery of organic liquid product from the cracking process varies start from 8.31% and the optimal results was 54.08%. The highest heating value of liquid product was resulted from catalytic cracking process at temperature of 450°C with value of 10880.48 cal/gr and the highest product yield with 54.08% recovery was achieved from thermal cracking process with temperature of 450°C.

Catalytic conversion of CO, NO and SO2 on supported sulfide catalysts. Part 2. Catalytic reduction of NO and SO2 by CO

International Nuclear Information System (INIS)

Zhuang, S.-X.; Yamazaki, M.; Omata, K.; Takahashi, Y.; Yamada, M.

2001-01-01

To investigate the possibility of simultaneous catalytic reduction of NO and SO 2 by CO, reactions of NO, NO-CO, and NO-SO 2 -CO were performed on γ-alumina-supported sulfides of transition metals including Co, Mo, CoMo and FeMo. NO was decomposed into N 2 O and N 2 accompanied with the formation of SO 2 ; this serious oxidation of lattice sulfur resulted in the deactivation of the catalysts. The addition of CO to the NO stream suppressed SO 2 formation and yielded COS instead. A stoichiometric conversion of NO and CO to N 2 and CO 2 was observed above 350C on the CoMo and the FeMo catalysts. Although the CO addition lengthened catalyst life, it was not enough to maintain activity. After the NO-CO reaction, an XPS analysis showed the growth of Mo 6+ and SO 4 2- peaks, especially for the sulfided FeMo/Al 2 O 3 ; the FeMo catalyst underwent strong oxidation in the NO-CO reaction. The NO and the NO-CO reactions proceeded non-catalytically, consuming catalyst lattice sulfur to yield SO 2 or COS. The addition of SO 2 in the NO-CO system enabled in situ regeneration of the catalysts; the catalysts oxidized through abstraction of lattice sulfur experienced anew reduction and sulfurization through the SO 2 -CO reaction at higher temperature. NO and SO 2 were completely and catalytically converted at 400C on the sulfided CoMo/Al 2 O 3 . By contrast, the sulfided FeMo/Al 2 O 3 was easily oxidized by NO and hardly re-sulfided under the test conditions. Oxidation states of the metals before and after the reactions were determined. Silica and titania-supported CoMo catalysts were also evaluated to study support effects

Catalytic methanol dissociation

International Nuclear Information System (INIS)

Alcinikov, Y.; Fainberg, V.; Garbar, A.; Gutman, M.; Hetsroni, G.; Shindler, Y.; Tatrtakovsky, L.; Zvirin, Y.

1998-01-01

Results of the methanol dissociation study on copper/potassium catalyst with alumina support at various temperatures are presented. The following gaseous and liquid products at. The catalytic methanol dissociation is obtained: hydrogen, carbon monoxide, carbon dioxide, methane, and dimethyl ether. Formation rates of these products are discussed. Activation energies of corresponding reactions are calculated

Comparative catalytic activity of PET track-etched membranes with embedded silver and gold nanotubes

Science.gov (United States)

Mashentseva, Anastassiya; Borgekov, Daryn; Kislitsin, Sergey; Zdorovets, Maxim; Migunova, Anastassiya

2015-12-01

Irradiated by heavy ions nanoporous polyethylene terephthalate track-etched membranes (PET TeMs) after +15Kr84 ions bombardment (1.75 MeV/nucl with the ion fluency of 1 × 109 cm-2) and sequential etching was applied in this research as a template for development of composites with catalytically enriched properties. A highly ordered silver and gold nanotubes arrays were embedded in 100 nm pores of PET TeMs via electroless deposition technique at 4 °C during 1 h. All "as-prepared" composites were examined for catalytic activity using reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) by sodium borohydride as a common reaction to test metallic nanostructures catalysts. The effect of temperature on the catalytic activity was investigated in range of 292-313 K and activation energy were calculated. Kapp of Ag/PET composites linearly increase with an increase of the temperature thus normal Arrhenius behavior have been seen and the activation energy was calculated to be 42.13 kJ/mol. Au/PET composites exhibit not only more powerful catalytic activity but also non-linear dependence of rate constant from temperature. Kapp increased with increasing temperature throughout the 292-308 K temperature range; the reaction had an activation energy 65.32 kJ/mol. In range 311-313 K rate constant dramatically decreased and the apparent activation energy at this temperature rang was -91.44 kJ/mol due some structural changes, i.e. agglomeration of Au nanoparticles on the surface of composite.

Highly Dense Isolated Metal Atom Catalytic Sites

DEFF Research Database (Denmark)

Chen, Yaxin; Kasama, Takeshi; Huang, Zhiwei

2015-01-01

-ray diffraction. A combination of electron microscopy images with X-ray absorption spectra demonstrated that the silver atoms were anchored on five-fold oxygen-terminated cavities on the surface of the support to form highly dense isolated metal active sites, leading to excellent reactivity in catalytic oxidation......Atomically dispersed noble-metal catalysts with highly dense active sites are promising materials with which to maximise metal efficiency and to enhance catalytic performance; however, their fabrication remains challenging because metal atoms are prone to sintering, especially at a high metal...... loading. A dynamic process of formation of isolated metal atom catalytic sites on the surface of the support, which was achieved starting from silver nanoparticles by using a thermal surface-mediated diffusion method, was observed directly by using in situ electron microscopy and in situ synchrotron X...

Including lateral interactions into microkinetic models of catalytic reactions

DEFF Research Database (Denmark)

Hellman, Anders; Honkala, Johanna Karoliina

2007-01-01

In many catalytic reactions lateral interactions between adsorbates are believed to have a strong influence on the reaction rates. We apply a microkinetic model to explore the effect of lateral interactions and how to efficiently take them into account in a simple catalytic reaction. Three differ...... different approximations are investigated: site, mean-field, and quasichemical approximations. The obtained results are compared to accurate Monte Carlo numbers. In the end, we apply the approximations to a real catalytic reaction, namely, ammonia synthesis....

Reduced differential transform method for partial differential equations within local fractional derivative operators

Directory of Open Access Journals (Sweden)

Hossein Jafari

2016-04-01

Full Text Available The non-differentiable solution of the linear and non-linear partial differential equations on Cantor sets is implemented in this article. The reduced differential transform method is considered in the local fractional operator sense. The four illustrative examples are given to show the efficiency and accuracy features of the presented technique to solve local fractional partial differential equations.