WorldWideScience

Sample records for part iii comparing

  1. Workshop 96. Part III

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    Part III of the proceedings contain 155 contributions in various fields of science and technology including nuclear engineering, environmental science, and biomedical engineering. Out of these, 10 were selected to be inputted in INIS. (P.A.).

  2. Workshop 96. Part III

    International Nuclear Information System (INIS)

    1995-12-01

    Part III of the proceedings contain 155 contributions in various fields of science and technology including nuclear engineering, environmental science, and biomedical engineering. Out of these, 10 were selected to be inputted in INIS. (P.A.)

  3. Introduction to Part III: Application of LCA in Practice

    DEFF Research Database (Denmark)

    Rosenbaum, Ralph K.

    2018-01-01

    While Part II of this book presents the theoretical foundation and methodology of LCA, Part III is dedicated to a comprehensive discussion of how this methodology has been adapted and applied in practice. The chapters of Part III provide an easily readable and accessible introduction to different...

  4. Neuroscience in Nazi Europe Part III

    DEFF Research Database (Denmark)

    Zeidman, Lawrence A; Kondziella, Daniel

    2012-01-01

    In Part I, neuroscience collaborators with the Nazis were discussed, and in Part II, neuroscience resistors were discussed. In Part III, we discuss the tragedy regarding european neuroscientists who became victims of the Nazi onslaught on “non-Aryan” doctors. Some of these unfortunate...... of neuroscience, we pay homage and do not allow humanity to forget, lest this dark period in history ever repeat itself....

  5. Warship Radar Signatures (Ship Survivability Part III-A)

    NARCIS (Netherlands)

    Galle, L.F.; Heemskerk, H.J.M.; Ewijk, L.J. van

    2000-01-01

    Radar Cross Section (RCS) management is of paramount importance for a warships's survivability. In this first part of the paper (Part III-A), the operational benefits of low RCS will be explained. Basic RCS theory, measurement and simulation techniques will be addressed. The RCS of representative

  6. 12 CFR Appendix III to Part 27 - Fair Housing Lending Inquiry/Application Log Sheet

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Fair Housing Lending Inquiry/Application Log Sheet III Appendix III to Part 27 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY FAIR HOUSING HOME LOAN DATA SYSTEM Pt. 27, App. III Appendix III to Part 27—Fair Housing Lending...

  7. Solar neutrino oscillation parameters after SNO Phase-III and SAGE Part-III

    International Nuclear Information System (INIS)

    Yang Ping; Liu Qiuyu

    2009-01-01

    We analyse the recently published results from solar neutrino experiments SNO Phase-III and SAGE Part-III and show their constraints on solar neutrino oscillation parameters, especially for the mixing angle θ 12 . Through a global analysis using all existing data from SK, SNO, Ga and Cl radiochemical experiments and long base line reactor experiment KamLAND , we obtain the parameters Δm 12 2 =7.684 -0.208 +0.212 x 10 -5 eV 2 , tan 2 θ 12 =0.440 -0.057 +0.059 . We also find that the discrepancy between the KamLAND and solar neutrino results can be reduced by choosing a small non-zero value for the mixing angle θ 13 . (authors)

  8. 18 CFR 410.1 - Basin regulations-Water Code and Administrative Manual-Part III Water Quality Regulations.

    Science.gov (United States)

    2010-04-01

    ... Code and Administrative Manual-Part III Water Quality Regulations. 410.1 Section 410.1 Conservation of... CODE AND ADMINISTRATIVE MANUAL-PART III WATER QUALITY REGULATIONS § 410.1 Basin regulations—Water Code and Administrative Manual—Part III Water Quality Regulations. (a) The Water Code of the Delaware River...

  9. Mandibular dimensions of subjects with asymmetric skeletal class III malocclusion and normal occlusion compared with cone-beam computed tomography.

    Science.gov (United States)

    Lee, HyoYeon; Bayome, Mohamed; Kim, Seong-Hun; Kim, Ki Beom; Behrents, Rolf G; Kook, Yoon-Ah

    2012-08-01

    The purpose of this study was to use cone-beam computed tomography to compare mandibular dimensions in subjects with asymmetric skeletal Class III malocclusion and those with normal occlusion. Cone-beam computed tomography scans of 38 subjects with normal occlusion and 28 patients with facial asymmetry were evaluated and digitized with Invivo software (Anatomage, San Jose, Calif). Three midsagittal and 13 right and left measurements were taken. The paired t test was used to compare the right and left sides in each group. The Mann-Whitney U test was used to compare the midsagittal variables and the differences between the 2 sides of the group with normal occlusion with those of asymmetry patients. The posterior part of the mandibular body showed significant differences between the deviated and nondeviated sides in asymmetric Class III patients. The difference of the asymmetry group was significantly greater than that of the normal occlusion group for the mediolateral ramal and the anteroposterior condylar inclinations (P = 0.007 and P = 0.019, respectively). The asymmetric skeletal Class III group showed significant differences in condylar height, ramus height, and posterior part of the mandibular body compared with the subjects with normal occlusion. These results might be useful for diagnosis and treatment planning of asymmetric Class III patients. Copyright © 2012 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

  10. A comparative study of ion exchange properties of antimony (III) tungstoselenite with those of antimony (III) tungstate and antimony (III) selenite

    International Nuclear Information System (INIS)

    Janardanan, C.; Nair, S.M.K.

    1996-01-01

    A new inorganic ion exchanger, antimony (III) tungstoselenite, has been prepared and characterised. Its exchange capacity and distribution coefficients for various metal ions and the effects of temperature and electrolyte concentrations on ion exchange capacity have been compared with antimony (III) tungstate and antimony (III) selenite. Six binary separations using the exchanger have been carried out. (author). 7 refs., 1 tab

  11. Standards in neurosonology. Part III

    Directory of Open Access Journals (Sweden)

    Joanna Wojczal

    2016-06-01

    Full Text Available The paper presents standards related to ultrasound imaging of the cerebral vasculature and structures. The aim of this paper is to standardize both the performance and description of ultrasound imaging of the extracranial and intracranial cerebral arteries as well as a study of a specific brain structure, i.e. substantia nigra hyperechogenicity. The following aspects are included in the description of standards for each ultrasonographic method: equipment requirements, patient preparation, study technique and documentation as well as the required elements of ultrasound description. Practical criteria for the diagnosis of certain pathologies in accordance with the latest literature were also presented. Furthermore, additional comments were included in some of the sections. Part I discusses standards for the performance, documentation and description of different ultrasound methods (Duplex, Doppler. Part II and III are devoted to standards for specific clinical situations (vasospasm, monitoring after the acute stage of stroke, detection of a right-to-left shunts, confirmation of the arrest of the cerebral circulation, an assessment of the functional efficiency of circle of Willis, an assessment of the cerebrovascular vasomotor reserve as well as the measurement of substantia nigra hyperechogenicity.

  12. 40 CFR Appendix III to Part 600 - Sample Fuel Economy Label Calculation

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Sample Fuel Economy Label Calculation...) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Pt. 600, App. III Appendix III to Part 600—Sample Fuel Economy Label Calculation Suppose that a manufacturer called Mizer...

  13. Some Aspects of Facial Nerve Paralysis. Part III. Complications ...

    African Journals Online (AJOL)

    Some Aspects of Facial Nerve Paralysis. Part III. Complications, Prognosis and management. ... It should be possible to set a definite prognosis within 2 weeks after the onset of facial paralysis, and in many cases even sooner. In the prognosis of facial paralysis the aetiological and time factors involved, the completeness of ...

  14. Active Control of Low-Speed Fan Tonal Noise Using Actuators Mounted in Stator Vanes: Part III Results

    Science.gov (United States)

    Sutliff, Daniel L.; Remington, Paul J.; Walker, Bruce E.

    2003-01-01

    A test program to demonstrate simplification of Active Noise Control (ANC) systems relative to standard techniques was performed on the NASA Glenn Active Noise Control Fan from May through September 2001. The target mode was the m = 2 circumferential mode generated by the rotor-stator interaction at 2BPF. Seven radials (combined inlet and exhaust) were present at this condition. Several different error-sensing strategies were implemented. Integration of the error-sensors with passive treatment was investigated. These were: (i) an in-duct linear axial array, (ii) an induct steering array, (iii) a pylon-mounted array, and (iv) a near-field boom array. The effect of incorporating passive treatment was investigated as well as reducing the actuator count. These simplified systems were compared to a fully ANC specified system. Modal data acquired using the Rotating Rake are presented for a range of corrected fan rpm. Simplified control has been demonstrated to be possible but requires a well-known and dominant mode signature. The documented results here in are part III of a three-part series of reports with the same base title. Part I and II document the control system and error-sensing design and implementation.

  15. 29 CFR Appendix III to Part 1918 - The Mechanics of Conventional Cargo Gear (Non-mandatory)

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false The Mechanics of Conventional Cargo Gear (Non-mandatory.... 1918, App. III Appendix III to Part 1918—The Mechanics of Conventional Cargo Gear (Non-mandatory) Note: This appendix is non-mandatory and provides an explanation of the mechanics in the correct spotting of...

  16. International Working Group on Past Reactors Thirteenth Annual Meeting. Summary Report. Part III

    International Nuclear Information System (INIS)

    1981-04-01

    The Thirteenth Annual Meeting of the IAEA International Working Group on Fast Reactors was held at the IAEA Headquarters, Vienna, Austria from 9 to 11 April 1980. The Summary Report (Part I) contains the Minutes of the Meeting. The Summary Report (Part II) contains the papers which review the national programme in the field of LMFBRs and other presentations at the Meeting. The Summary Report (Part III) contains the discussions on the review of the national programmes

  17. 40 CFR Appendix III to Part 266 - Tier II Emission Rate Screening Limits for Free Chlorine and Hydrogen Chloride

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Tier II Emission Rate Screening Limits for Free Chlorine and Hydrogen Chloride III Appendix III to Part 266 Protection of Environment... to Part 266—Tier II Emission Rate Screening Limits for Free Chlorine and Hydrogen Chloride Terrain...

  18. ATWS: a reappraisal. Part III. Frequency of anticipated transients. Interim report

    International Nuclear Information System (INIS)

    Leverenz, F.L. Jr.; Koren, J.M.; Erdmann, R.C.; Lellouche, G.S.

    1978-07-01

    The document is Part III of the Institute study of the ATWS question. The frequencies of the various events which have led to a reactor scram are documented from the nuclear power plant records. Some of these events, in the absence of scram, could lead to undesirable system response and are the ''transients of significance'' which comprise the anticipated transients of the ATWS question

  19. Neuroscience in Nazi Europe Part III: victims of the Third Reich.

    Science.gov (United States)

    Zeidman, Lawrence A; Kondziella, Daniel

    2012-11-01

    In Part I, neuroscience collaborators with the Nazis were discussed, and in Part II, neuroscience resistors were discussed. In Part III, we discuss the tragedy regarding european neuroscientists who became victims of the Nazi onslaught on “non-Aryan” doctors. Some of these unfortunate neuroscientists survived Nazi concentration camps, but most were murdered. We discuss the circumstances and environment which stripped these neuroscientists of their profession, then of their personal rights and freedom, and then of their lives. We include a background analysis of anti-Semitism and Nazism in their various countries, then discuss in depth seven exemplary neuroscientist Holocaust victims; including Germans Ludwig Pick, Arthur Simons, and Raphael Weichbrodt, Austrians Alexander Spitzer and Viktor Frankl, and Poles Lucja Frey and Wladyslaw Sterling. by recognizing and remembering these victims of neuroscience, we pay homage and do not allow humanity to forget, lest this dark period in history ever repeat itself.

  20. Market Analysis and Consumer Impacts Source Document. Part III. Consumer Behavior and Attitudes Toward Fuel Efficient Vehicles

    Science.gov (United States)

    1980-12-01

    This source document on motor vehicle market analysis and consumer impacts consists of three parts. Part III consists of studies and reviews on: consumer awareness of fuel efficiency issues; consumer acceptance of fuel efficient vehicles; car size ch...

  1. 10 CFR Appendix III to Part 960 - Application of the System and Technical Guidelines During the Siting Process

    Science.gov (United States)

    2010-01-01

    ... 960—Application of the System and Technical Guidelines During the Siting Process 1. This appendix... 10 Energy 4 2010-01-01 2010-01-01 false Application of the System and Technical Guidelines During the Siting Process III Appendix III to Part 960 Energy DEPARTMENT OF ENERGY GENERAL GUIDELINES FOR THE...

  2. Social class, political power, and the state: their implications in medicine--part III.

    Science.gov (United States)

    Navarro, V

    1977-01-01

    This is the third part of an article on the distribution of power and the nature of the state in Western industrialized societies and their implications in medicine. Parts I and II were published in the preceding issue of this Journal. Part I presented a critique of contemporary theories of the Western system of power; discussed the countervailing pluralist and power of elite theories, as well as those of bureaucratic and professional control; and concluded with an examination of the Marxist theories of economic determinism, structural determinism, and corporate statism. Part II presented a Marxist theory of the role, nature, and characteristics of state intervention. Part III focuses on the mode of that intervention and the reasons for its growth, with an added analysis of the attributes of state intervention in the health sector, and of the dialectical relationship between its growth and the current fiscal crisis of the state. In all three parts, the focus is on Western European countries and on North America, with many examples and categories from the area of medicine.

  3. Thermal sensation and comfort models for non-uniform and transient environments: Part III: whole-body sensation and comfort

    OpenAIRE

    Zhang, Hui; Arens, Edward; Huizenga, Charlie; Han, Taeyoung

    2009-01-01

    A three-part series presents the development of models for predicting the local thermal sensation (Part I) and local thermal comfort (Part II) of different parts of the human body, and also the whole-body sensation and comfort (Part III) that result from combinations of local sensation and comfort. The models apply to sedentary activities in a range of environments: uniform and non-uniform, stable and transient. They are based on diverse findings from the literature and from body-part-specifi...

  4. Eleventh annual meeting, Bologna, Italy, 17-20 April 1978. Summary report. Part III

    International Nuclear Information System (INIS)

    1978-09-01

    The Summary Report - Part III of the Eleventh Annual Meeting of the IAEA International Working Group on Fast Reactors - contains the discussions on the commercialization LMFBRs according to national plans, mostly related to technology of fuel fabrication, PHENIX fuel pins testing, heterogeneous cores, in service inspection of fuel elements, regulations and licensing, and related OECD activities. Most of the discussions were related to the existing reactors: BR-10, BN-600, BN-350, BN-1600, RAPSODIE and PHENIX

  5. Eleventh annual meeting, Bologna, Italy, 17-20 April 1978. Summary report. Part III

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-09-01

    The Summary Report - Part III of the Eleventh Annual Meeting of the IAEA International Working Group on Fast Reactors - contains the discussions on the commercialization LMFBRs according to national plans, mostly related to technology of fuel fabrication, PHENIX fuel pins testing, heterogeneous cores, in service inspection of fuel elements, regulations and licensing, and related OECD activities. Most of the discussions were related to the existing reactors: BR-10, BN-600, BN-350, BN-1600, RAPSODIE and PHENIX.

  6. A-Part Gel, an adhesion prophylaxis for abdominal surgery: a randomized controlled phase I-II safety study [NCT00646412].

    Science.gov (United States)

    Lang, Reinhold; Baumann, Petra; Schmoor, Claudia; Odermatt, Erich K; Wente, Moritz N; Jauch, Karl-Walter

    2015-01-01

    Intra-abdominal surgical intervention can cause the development of intra-peritoneal adhesions. To reduce this problem, different agents have been tested to minimize abdominal adhesions; however, the optimal adhesion prophylaxis has not been found so far. Therefore, the A-Part(®) Gel was developed as a barrier to diminish postsurgical adhesions; the aim of this randomized controlled study was a first evaluation of its safety and efficacy. In this prospective, controlled, randomized, patient-blinded, monocenter phase I-II study, 62 patients received either the hydrogel A-Part-Gel(®) as an anti-adhesive barrier or were untreated after primary elective median laparotomy. Primary endpoint was the occurrence of peritonitis and/or wound healing impairment 28 ± 10 days postoperatively. As secondary endpoints anastomotic leakage until 28 days after surgery, adverse events and adhesions were assessed until 3 months postoperatively. A lower rate of wound healing impairment and/or peritonitis was observed in the A-Part Gel(®) group compared to the control group: (6.5 vs. 13.8 %). The difference between the two groups was -7.3%, 90 % confidence interval [-20.1, 5.4 %]. Both treatment groups showed similar frequency of anastomotic leakage but incidence of adverse events and serious adverse events were slightly lower in the A-Part Gel(®) group compared to the control. Adhesion rates were comparable in both groups. A-Part Gel(®) is safe as an adhesion prophylaxis after abdominal wall surgery but no reduction of postoperative peritoneal adhesion could be found in comparison to the control group. This may at least in part be due to the small sample size as well as to the incomplete coverage of the incision due to the used application. NCT00646412.

  7. Tenth annual meeting, Vienna, Austria, 29 March - 1 April 1977. Summary report. Part III

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-11-01

    The Summary Report - Part III of the Tenth Annual Meeting of the IAEA International Working Group on Fast Reactors - contains the discussions on the commercial development of FBRs according to national plans, mostly related to technology problems of containment design, fuel fabrication, fuel failures, sodium pressure, fuel-sodium interaction, computer codes needed for licensing. Most of the discussions were related to the existing reactors: BN-600, BN-350, BN-1600, BOR-60, RAPSODIE, PHENIX.

  8. Tenth annual meeting, Vienna, Austria, 29 March - 1 April 1977. Summary report. Part III

    International Nuclear Information System (INIS)

    1977-11-01

    The Summary Report - Part III of the Tenth Annual Meeting of the IAEA International Working Group on Fast Reactors - contains the discussions on the commercial development of FBRs according to national plans, mostly related to technology problems of containment design, fuel fabrication, fuel failures, sodium pressure, fuel-sodium interaction, computer codes needed for licensing. Most of the discussions were related to the existing reactors: BN-600, BN-350, BN-1600, BOR-60, RAPSODIE, PHENIX

  9. Fracture toughness of A533B Part III - variability of A533B fracture toughness as determined from Charpy data

    International Nuclear Information System (INIS)

    Druce, S.G.; Eyre, B.L.

    1978-08-01

    This is the final part of a series of three reports examining the upper shelf fracture toughness of A533B Class 1 pressure vessel steel. Part I (AERE R 8968) critically reviews the current elasto plastic fracture mechanics methodologies employed to characterise toughness following extensive yielding and Part II (AERE R 8969) examines several sources of fracture mechanics data pertinent to A533B Class 1 in the longitudinal (RW) orientation. Part III is a review of the effects of (i) position and orientation within the plate (ii) welding processes and post weld heat treatment and (iii) neutron irradiation as measured by Charpy impact testing. It is concluded that the upper shelf factor energy is dependent on orientation and position and can be reduced by welding, extended post weld heat treatments and neutron irradiation. Neutron irradiation effects are known to be strongly dependent on composition and metallurgical conditions, but an explanation for the variability following extended post weld treatments has yet to be resolved. (author)

  10. Thallium (III) salts utilization in organic synthesis. Part II

    International Nuclear Information System (INIS)

    Ferraz, H.M.C.

    1989-01-01

    The utilizations of thallium (III) salts in organic synthesis with carbonylic and acitylenic substrates are presented. The reactions of carbonylic substra3ts with kitones and the oxidation reactions of acetylenic substrates are shown. Others reactions including thallium (III) salts and non aromatic unsatured substracts, as cleasage of ethers and epoxide using thallium trinitrate, hydrazones treatments with thallium triacetates, etc, are also mentioned. (C.G.C.) [pt

  11. Building human resources capability in health care: a global analysis of best practice--Part III.

    Science.gov (United States)

    Zairi, M

    1998-01-01

    This is the last part of a series of three papers which discussed very comprehensively best practice applications in human resource management by drawing special inferences to the healthcare context. It emerged from parts I and II that high performing organisations plan and intend to build sustainable capability through a systematic consideration of the human element as the key asset and through a continuous process of training, developing, empowering and engaging people in all aspects of organisational excellence. Part III brings this debate to a close by demonstrating what brings about organisational excellence and proposes a road map for effective human resource development and management, based on world class standards. Healthcare human resource professionals can now rise to the challenge and plan ahead for building organisational capability and sustainable performance.

  12. Comparative analysis of SLB for OPR1000 by using MEDUSA and CESEC-III codes

    International Nuclear Information System (INIS)

    Park, Jong Cheol; Park, Chan Eok; Kim, Shin Whan

    2005-01-01

    The MEDUSA is a system thermal hydraulics code developed by Korea Power Engineering Company (KOPEC) for Non-LOCA and LOCA analysis, using two fluid, three-field governing equations for two phase flow. The detailed descriptions for the MEDUSA code are given in Reference. A lot of effort is now being made to investigate the applicability of the MEDUSA code especially to Non-LOCA analysis, by comparing the analysis results with those from the current licensing code, CESEC-III: The comparative simulations of Pressurizer Level Control System(PLCS) Malfunction and Feedwater Line Break(FLB), which have been accomplished by C.E.Park and M.T.Oh, respectively, already showed that the MEDUSA code is applicable to the analysis of Non-LOCA events. In this paper, detailed thermal hydraulic analyses for Steam Line Break(SLB) without loss of off-site power were performed using the MEDUSA code. The calculation results were also compared with the CESEC-III, 1000(OPR1000), for the purpose of the code verification

  13. Towards an interpretation of the mechanism of the actinides(III)/lanthanides(III) separation by synergistic solvent extraction with nitrogen-containing polydendate ligands; Vers une interpretation des mecanismes de la separation actinides(III)/lanthanides(III) par extraction liquide-liquide synergique impliquant des ligands polyazotes

    Energy Technology Data Exchange (ETDEWEB)

    Francois, N [CEA/VALRHO - site de Marcoule, Dept. de Recherche en Retraitement et en Vitrification, (DRRV), 30 - Marcoule (France); Universite Henri Poincare, 54 - Vandoeuvre-les-Nancy (France)

    2000-07-01

    In the field of the separation of long-lived radionuclides from the wastes produced by nuclear fuel reprocessing, aromatic nitrogen-containing polydendate ligands are potential candidates for the selective extraction, alone or in synergistic mixture with acidic extractants, of trivalent actinides from trivalent lanthanides. The first part of this work deals with the complexation of trivalent f cations with various nitrogen-containing ligands (poly-pyridine analogues). Time-resolved laser-induced fluorimetry (TRLIF) and UV-visible spectrophotometry were used to determine the nature and evaluate the stability of each complex. Among the ligands studied, the least basic Me-Btp proved to be highly selective towards americium(III) in acidic solution. In the second part, two synergistic systems (nitrogen-containing polydendate ligand and lipophilic carboxylic acid) are studied and compared in regard to the extraction and separation of lanthanides(III) and actinides(III). TRLIF and gamma spectrometry allowed the nature of the extracted complexes and the optimal conditions of efficiency of both systems to be determined. Comparison between these different studies showed that the selectivity of complexation of trivalent f cations by a given nitrogen-containing polydendate ligand could not always be linked to the Am(III)Eu(III) selectivity reached in synergistic extraction. The latter depends on the 'balance' between the acid-basic properties on the one hand, and on the hard-soft characteristics on the other hand, of both components of synergistic system. (author)

  14. Towards an interpretation of the mechanism of the actinides(III)/lanthanides(III) separation by synergistic solvent extraction with nitrogen-containing polydendate ligands; Vers une interpretation des mecanismes de la separation actinides(III)/lanthanides(III) par extraction liquide-liquide synergique impliquant des ligands polyazotes

    Energy Technology Data Exchange (ETDEWEB)

    Francois, N. [CEA/VALRHO - site de Marcoule, Dept. de Recherche en Retraitement et en Vitrification, (DRRV), 30 - Marcoule (France); Universite Henri Poincare, 54 - Vandoeuvre-les-Nancy (France)

    2000-07-01

    In the field of the separation of long-lived radionuclides from the wastes produced by nuclear fuel reprocessing, aromatic nitrogen-containing polydendate ligands are potential candidates for the selective extraction, alone or in synergistic mixture with acidic extractants, of trivalent actinides from trivalent lanthanides. The first part of this work deals with the complexation of trivalent f cations with various nitrogen-containing ligands (poly-pyridine analogues). Time-resolved laser-induced fluorimetry (TRLIF) and UV-visible spectrophotometry were used to determine the nature and evaluate the stability of each complex. Among the ligands studied, the least basic Me-Btp proved to be highly selective towards americium(III) in acidic solution. In the second part, two synergistic systems (nitrogen-containing polydendate ligand and lipophilic carboxylic acid) are studied and compared in regard to the extraction and separation of lanthanides(III) and actinides(III). TRLIF and gamma spectrometry allowed the nature of the extracted complexes and the optimal conditions of efficiency of both systems to be determined. Comparison between these different studies showed that the selectivity of complexation of trivalent f cations by a given nitrogen-containing polydendate ligand could not always be linked to the Am(III)Eu(III) selectivity reached in synergistic extraction. The latter depends on the 'balance' between the acid-basic properties on the one hand, and on the hard-soft characteristics on the other hand, of both components of synergistic system. (author)

  15. Comparing acquired angioedema with hereditary angioedema (types I/II): findings from the Icatibant Outcome Survey.

    Science.gov (United States)

    Longhurst, H J; Zanichelli, A; Caballero, T; Bouillet, L; Aberer, W; Maurer, M; Fain, O; Fabien, V; Andresen, I

    2017-04-01

    Icatibant is used to treat acute hereditary angioedema with C1 inhibitor deficiency types I/II (C1-INH-HAE types I/II) and has shown promise in angioedema due to acquired C1 inhibitor deficiency (C1-INH-AAE). Data from the Icatibant Outcome Survey (IOS) were analysed to evaluate the effectiveness of icatibant in the treatment of patients with C1-INH-AAE and compare disease characteristics with those with C1-INH-HAE types I/II. Key medical history (including prior occurrence of attacks) was recorded upon IOS enrolment. Thereafter, data were recorded retrospectively at approximately 6-month intervals during patient follow-up visits. In the icatibant-treated population, 16 patients with C1-INH-AAE had 287 attacks and 415 patients with C1-INH-HAE types I/II had 2245 attacks. Patients with C1-INH-AAE versus C1-INH-HAE types I/II were more often male (69 versus 42%; P = 0·035) and had a significantly later mean (95% confidence interval) age of symptom onset [57·9 (51·33-64·53) versus 14·0 (12·70-15·26) years]. Time from symptom onset to diagnosis was significantly shorter in patients with C1-INH-AAE versus C1-INH-HAE types I/II (mean 12·3 months versus 118·1 months; P = 0·006). Patients with C1-INH-AAE showed a trend for higher occurrence of attacks involving the face (35 versus 21% of attacks; P = 0·064). Overall, angioedema attacks were more severe in patients with C1-INH-HAE types I/II versus C1-INH-AAE (61 versus 40% of attacks were classified as severe to very severe; P types I/II, respectively. © 2016 British Society for Immunology.

  16. Japanese contributions to IAEA INTOR workshop, phase two A, part 2, chapter III: impurity control (engineering)

    International Nuclear Information System (INIS)

    Seki, Masahiro; Miki, Nobuharu; Shibutani, Yoji; Fujimura, Kaoru; Adachi, Jun-ichi; Sato, Kosuke; Fujii, Masaharu; Yamazaki, Seiichiro; Itoh, Shin-ichi.

    1985-07-01

    This report corresponds to the second half of Chapter III of Japanese contribution report to IAEA INTOR Workshop, Phase Two A, Part 2. Data base assessment are made on candidate materials for the divertor, limiter, and the first wall. Engineering trade-off studies are made for the high-recycling and low temperature conditions. The studies include material considerations, configuration, thermohydraulic and stress analysis, disruption, lifetime analysis, and tritium permeation. (author)

  17. Hadron component of families (exp. 'Pamir' III)

    International Nuclear Information System (INIS)

    Anon.

    1984-01-01

    Possibilities of nuclear interaction investigation at 10 15 - 10 16 ev by means of analysis of family hadron component, registered in carbon and deep lead x-ray emulsion chambers, are discussed. The paper is divided in three parts. General properties of hadron families are discribed and compared in C and Pb chambers (part I). Correlations between gamma and hadron components of families are studied in the part II. It is shown that fluctuations of energies of this component are wider than in usually used models of nuclear interactions. The ratio of single hadron flux to the flux of γ-families is connected with cross-section and energy dissipation of nuclear interactions at about 10 16 ev (part III). (author)

  18. Reactions of sigma-bonded organochromium(III)complexes

    International Nuclear Information System (INIS)

    Leslie, J.P. II.

    1975-12-01

    Three projects were carried out, each dealing with the kinetics and mechanism of reactions of sigma-bonded organochromium(III) complexes of the form (H 2 O) 5 CrR 2+ . Part I describes the kinetics of the reaction of dichloromethylchromium(III) ion with chromium(II) ion in aqueous acid. Part II deals with the radioexchange of 4-pyridinomethylchromium(III) ion with 51 Cr 2+ and the kinetics of formation of the organochromium species at 55 0 in 1 M H + . Part III deals with the reactions of Hg 2+ and CH 3 Hg + with a series of (H 2 O) 5 CrR 2+ complexes, in which R is an aliphatic alkyl group, a haloalkyl group, or an aralkyl group

  19. Tanzania 1895-1920 : Part III: 1914-1920s

    NARCIS (Netherlands)

    Dietz, A.J.

    2016-01-01

    An earlier version of this African Postal Heritage Paper was published as African Studies Centre Leiden Working Paper 119 / 2015: "A postal history of the First World War in Africa and its aftermath - German colonies; III Deutsch Ostafrika / German East Africa", written by Ton Dietz.

  20. The Moessbauer effect in Fe(III) HEDTA, Fe(III) EDTA, and Fe(III) CDTA compounds

    International Nuclear Information System (INIS)

    Prado, F.R.

    1989-01-01

    The dependence of Moessbauer spectra with pH value of Fe(III)HEDTA and Fe(III)CDTA compounds is studied. Informations on formation processes of LFe-O-FeL (L=ligand) type dimers by the relation of titration curves of Fe(III)EDTA, Fe(III)HEDTA and Fe(III)CDTA compounds with the series of Moessbauer spectra, are obtained. Some informations on Fe-O-Fe bond structure are also obtained. Comparing the titration curves with the series of Moessbauer spectra, it is concluded that the dimerization process begins when a specie of the form FeXOH α (X = EDTA, HEDTA, CDTA; α = -1, -2) arises. (M.C.K.) [pt

  1. Dental compensation for skeletal Class III malocclusion by isolated extraction of mandibular teeth. Part 1: Occlusal situation 12 years after completion of active treatment.

    Science.gov (United States)

    Zimmer, Bernd; Schenk-Kazan, Sarah

    2015-05-01

    The purpose of this work was to statistically evaluate the outcomes achieved by isolated extraction of mandibular teeth (second premolars or first molars) for Class III compensation. Part A of the study dealt with the quality of outcomes at the end of active treatment, using weighted Peer Assessment Rating (PAR) scores determined on the basis of casts for 25 (14 female and 11 male) consecutive patients aged 16 ± 1.7 years at the time of debonding. These results were compared to the scores in a randomly selected control group of 25 (14 female and 11 male) patients who were 14.7 ± 1.9 years old at debonding. Part B evaluated the long-term stability of the outcomes based on 12 (all of them female) patients available for examination after a mean of 11.8 years. The mean weighted PAR scores obtained in both study parts were analyzed for statistical differences using a two-tailed paired Student's t-test at a significance level of p ≤ 0.05. Mean weighted PAR scores of 4.76 ± 3.94 and 3.92 ± 3.44 were obtained in the Class III extraction group and the control group, respectively, at the end of active treatment. This difference was not significant (p = 0.49). Among the 12 longitudinal patients, the mean score increased from 4 ± 3.46 at debonding to 6.25 ± 3.67 by the end of the 11.8-year follow-up period. This difference was significant (p = 0.0008). Treatment of Class III anomalies by isolated extraction of lower premolars or molars can yield PAR scores similar to those achieved by standard therapies. These scores, while increasing significantly, remained at a clinically acceptable level over 11.8 years. Hence this treatment modality--intended for cases that border on requiring orthognathic surgery--may also be recommended from a long-term point of view.

  2. Towards an interpretation of the mechanism of the actinides(III)/lanthanides(III) separation by synergistic solvent extraction with nitrogen-containing polydendate ligands

    International Nuclear Information System (INIS)

    Francois, N.

    2000-01-01

    In the field of the separation of long-lived radionuclides from the wastes produced by nuclear fuel reprocessing, aromatic nitrogen-containing polydendate ligands are potential candidates for the selective extraction, alone or in synergistic mixture with acidic extractants, of trivalent actinides from trivalent lanthanides. The first part of this work deals with the complexation of trivalent f cations with various nitrogen-containing ligands (poly-pyridine analogues). Time-resolved laser-induced fluorimetry (TRLIF) and UV-visible spectrophotometry were used to determine the nature and evaluate the stability of each complex. Among the ligands studied, the least basic Me-Btp proved to be highly selective towards americium(III) in acidic solution. In the second part, two synergistic systems (nitrogen-containing polydendate ligand and lipophilic carboxylic acid) are studied and compared in regard to the extraction and separation of lanthanides(III) and actinides(III). TRLIF and gamma spectrometry allowed the nature of the extracted complexes and the optimal conditions of efficiency of both systems to be determined. Comparison between these different studies showed that the selectivity of complexation of trivalent f cations by a given nitrogen-containing polydendate ligand could not always be linked to the Am(III)Eu(III) selectivity reached in synergistic extraction. The latter depends on the 'balance' between the acid-basic properties on the one hand, and on the hard-soft characteristics on the other hand, of both components of synergistic system. (author)

  3. Comparing the utility of DSM-5 Section II and III antisocial personality disorder diagnostic approaches for capturing psychopathic traits.

    Science.gov (United States)

    Few, Lauren R; Lynam, Donald R; Maples, Jessica L; MacKillop, James; Miller, Joshua D

    2015-01-01

    The current study compares the 2 diagnostic approaches (Section II vs. Section III) included in the Diagnostic and Statistical Manual for Mental Disorders-5 (DSM-5; American Psychiatric Association, 2013) for diagnosis of antisocial personality disorder (ASPD) in terms of their relations with psychopathic traits and externalizing behaviors (EBs). The Section III approach to ASPD, which is more explicitly trait-based than the Section II approach, also includes a psychopathy specifier (PS) that was created with the goal of making the diagnosis of ASPD more congruent with psychopathy. In a community sample of individuals currently receiving mental health treatment (N = 106), ratings of the 2 DSM-5 diagnostic approaches were compared in relation to measures of psychopathy, as well as indices of EBs. Both DSM-5 ASPD approaches were significantly related to the psychopathy scores, although the Section III approach accounted for almost twice the amount of variance when compared with the Section II approach. Relatively little of this predictive advantage, however, was due to the PS, as these traits manifested little evidence of incremental validity in relation to existing psychopathy measures and EBs, with the exception of a measure of fearless dominance. Overall, the DSM-5 Section III diagnostic approach for ASPD is more convergent with the construct of psychopathy, from which ASPD was originally derived. These improvements, however, are due primarily to the new trait-based focus in the Section III ASPD diagnosis rather than the assessment of personality dysfunction or the inclusion of additional "psychopathy-specific" traits. (PsycINFO Database Record (c) 2015 APA, all rights reserved).

  4. Sparkle/PM3 for the modeling of europium(III), gadolinium(III), and terbium(III) complexes

    International Nuclear Information System (INIS)

    Freire, Ricardo O.; Rocha, Gerd B.; Simas, Alfredo M.

    2009-01-01

    The Sparkle/PM3 model is extended to europium(III), gadolinium(III), and terbium(III) complexes. The validation procedure was carried out using only high quality crystallographic structures, for a total of ninety-six Eu(III) complexes, seventy Gd(III) complexes, and forty-two Tb(III) complexes. The Sparkle/PM3 unsigned mean error, for all interatomic distances between the trivalent lanthanide ion and the ligand atoms of the first sphere of coordination, is: 0.080 A for Eu(III); 0.063 A for Gd(III); and 0.070 A for Tb(III). These figures are similar to the Sparkle/AM1 ones of 0.082 A, 0.061 A, and 0.068 A respectively, indicating they are all comparable parameterizations. Moreover, their accuracy is similar to what can be obtained by present-day ab initio effective core potential full geometry optimization calculations on such lanthanide complexes. Finally, we report a preliminary attempt to show that Sparkle/PM3 geometry predictions are reliable. For one of the Eu(III) complexes, BAFZEO, we created hundreds of different input geometries by randomly varying the distances and angles of the ligands to the central Eu(III) ion, which were all subsequently fully optimized. A significant trend was unveiled, indicating that more accurate local minima geometries cluster at lower total energies, thus reinforcing the validity of sparkle model calculations. (author)

  5. Comparative studies of neodymium (III)-selective PVC membrane sensors

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, Vinod K., E-mail: vinodfcy@iitr.ernet.in [Department of Chemistry, Indian Institute of Technology Roorkee, Roorkee 247 667 (India); Goyal, Rajendra N.; Sharma, Ram A. [Department of Chemistry, Indian Institute of Technology Roorkee, Roorkee 247 667 (India)

    2009-08-04

    Sensors based on two neutral ionophores, N,N'-bis((1H-pyrrol-2-yl)methylene)cyclohexane-1,2-diamine (L{sub 1}) and 3,3'-(cyclohexane-1,2-diylbis(azan-1-yl-1-ylidene) bis(methan-1-yl-1-ylidene)bis(5-hydroxymethyl)pyridine-2-ol) (L{sub 2}) are described for quantification of neodymium (III). Effect of various plasticizers; 2-nitrophenyloctylether (o-NPOE), dibutyl butylphosphonate (DBBP), tri-n-butyl phosphates (TBP), dioctylpthalate (DOP) and chloronapthalen (CN) and anion excluder, sodiumtetraphenylborate (NaTPB) has been studied. The membrane composition of PVC:o-NPOE:ionophore (L{sub 1}):NaTPB (w/w; mg) of 150:300:5:5 exhibited best performance. The sensor with ionophore (L{sub 1}) exhibits significantly enhanced selectivity towards neodymium (III) in the concentration range 5.0 x 10{sup -7} to 1.0 x 10{sup -2} M with a detection limit of 1.0 x 10{sup -7} M and a Nernstian compliance (19.8 {+-} 0.3 mV decade{sup -1} of activity) within pH range 4.0-8.0. The response time of sensor was found as 10 s. The influence of the membrane composition and possible interfering ions has also been investigated on the response properties of the electrode. The fast and stable response, good reproducibility and long-term stability of the sensor are observed. The sensor has been found to work satisfactorily in partially non-aqueous media up to 20% (v/v) content of methanol, ethanol or acetonitrile and could be used for a period of 3 months. The selectivity coefficients determined by using fixed interference method (FIM) indicate high selectivity for neodymium. The proposed electrode shows fairly good discrimination of neodymium (III) from other cations. The application of prepared sensor has been demonstrated in the determination of neodymium (III) in spiked water samples.

  6. Interaction of Eu(III) and Cm(III) with mucin. A key component of the human mucosa

    International Nuclear Information System (INIS)

    Wilke, Claudia; Barkleit, Astrid

    2017-01-01

    To evaluate the potential health risks caused by the ingestion of lanthanides (Ln) and actinides (An), investigations into the chemical behavior of these metals in the human gastrointestinal tract are necessary. Mucin is an important part of the protective mucosa layer in the digestive system. We have recently reported that mucin interacts strongly with Eu(III) and Cm(III), representatives of Ln(III) and An(III), respectively, under in vivo conditions. In order to investigate the complexation behavior of this protein with Ln(III)/An(III), TRLFS measurements were performed on Eu(III)/Cm(III)-mucin solutions with different protein concentrations and at different pH. The results indicate the formation of at least two independent mucin species. At higher pH, the formation of hydroxide species was also observed.

  7. Interaction of Eu(III) and Cm(III) with mucin. A key component of the human mucosa

    Energy Technology Data Exchange (ETDEWEB)

    Wilke, Claudia; Barkleit, Astrid [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Chemistry of the F-Elements

    2017-06-01

    To evaluate the potential health risks caused by the ingestion of lanthanides (Ln) and actinides (An), investigations into the chemical behavior of these metals in the human gastrointestinal tract are necessary. Mucin is an important part of the protective mucosa layer in the digestive system. We have recently reported that mucin interacts strongly with Eu(III) and Cm(III), representatives of Ln(III) and An(III), respectively, under in vivo conditions. In order to investigate the complexation behavior of this protein with Ln(III)/An(III), TRLFS measurements were performed on Eu(III)/Cm(III)-mucin solutions with different protein concentrations and at different pH. The results indicate the formation of at least two independent mucin species. At higher pH, the formation of hydroxide species was also observed.

  8. Cubby : Multiscreen Desktop VR Part III

    NARCIS (Netherlands)

    Djajadiningrat, J.P.; Gribnau, M.W.

    2000-01-01

    In this month's final episode of our 'Cubby: Multiscreen Desktop VR' trilogy we explain how you read the InputSprocket driver from part II, how you use it as input for the cameras from part I and how you calibrate the input device so that it leads to the correct head position.

  9. Comparative genomics and transcriptomics of lineages I, II, and III strains of Listeria monocytogenes

    Directory of Open Access Journals (Sweden)

    Hain Torsten

    2012-04-01

    Full Text Available Abstract Background Listeria monocytogenes is a food-borne pathogen that causes infections with a high-mortality rate and has served as an invaluable model for intracellular parasitism. Here, we report complete genome sequences for two L. monocytogenes strains belonging to serotype 4a (L99 and 4b (CLIP80459, and transcriptomes of representative strains from lineages I, II, and III, thereby permitting in-depth comparison of genome- and transcriptome -based data from three lineages of L. monocytogenes. Lineage III, represented by the 4a L99 genome is known to contain strains less virulent for humans. Results The genome analysis of the weakly pathogenic L99 serotype 4a provides extensive evidence of virulence gene decay, including loss of several important surface proteins. The 4b CLIP80459 genome, unlike the previously sequenced 4b F2365 genome harbours an intact inlB invasion gene. These lineage I strains are characterized by the lack of prophage genes, as they share only a single prophage locus with other L. monocytogenes genomes 1/2a EGD-e and 4a L99. Comparative transcriptome analysis during intracellular growth uncovered adaptive expression level differences in lineages I, II and III of Listeria, notable amongst which was a strong intracellular induction of flagellar genes in strain 4a L99 compared to the other lineages. Furthermore, extensive differences between strains are manifest at levels of metabolic flux control and phosphorylated sugar uptake. Intriguingly, prophage gene expression was found to be a hallmark of intracellular gene expression. Deletion mutants in the single shared prophage locus of lineage II strain EGD-e 1/2a, the lma operon, revealed severe attenuation of virulence in a murine infection model. Conclusion Comparative genomics and transcriptome analysis of L. monocytogenes strains from three lineages implicate prophage genes in intracellular adaptation and indicate that gene loss and decay may have led to the emergence

  10. Antipsychotics and Sexual Dysfunction: Sexual Dysfunction - Part III

    Directory of Open Access Journals (Sweden)

    Anil Kumar Mysore Nagaraj

    2009-11-01

    Full Text Available Satisfying sexual experience is an essential part of a healthy and enjoyable life for most people. Antipsychotic drugs are among the various factors that affect optimal sexual functioning. Both conventional and novel antipsychotics are associated with significant sexual side effects. This review has presented various studies comparing different antipsychotic drugs. Dopamine antagonism, increased serum prolactin, serotonergic, adrenergic and cholinergic mechanisms are all proposed to be the mechanisms for sexual dysfunction. Drug treatment for this has not given satisfactory long-term results. Knowledge of the receptor pharmacology of an individual antipsychotic will help to determine whether it is more or less likely to cause sexual side effects and its management.

  11. PACE. A Program for Acquiring Competence in Entrepreneurship. Part III: Being an Entrepreneur. Unit B: Financial Management. Research and Development Series No. 194 C-2.

    Science.gov (United States)

    Ohio State Univ., Columbus. National Center for Research in Vocational Education.

    This three-part curriculum for entrepreneurship education is primarily for postsecondary level, including four-year colleges and adult education, but it can be adapted for special groups or vocational teacher education. The emphasis of the eight instructional units in Part III is operating a business. Unit B focuses on good financial management…

  12. PACE. A Program for Acquiring Competence in Entrepreneurship. Part III: Being an Entrepreneur. Unit H: Business Protection. Research and Development Series No. 194 C-8.

    Science.gov (United States)

    Ohio State Univ., Columbus. National Center for Research in Vocational Education.

    This three-part curriculum for entrepreneurship education is primarily for postsecondary level, including four-year colleges and adult education, but it can be adapted for special groups or vocational teacher education. The emphasis of the eight instructional units in part III is operating a business. Unit H focuses on business protection. It…

  13. PACE. A Program for Acquiring Competence in Entrepreneurship. Part III: Being an Entrepreneur. Unit G: Community Relations. Research and Development Series No. 194 C-7.

    Science.gov (United States)

    Ohio State Univ., Columbus. National Center for Research in Vocational Education.

    This three-part curriculum for entrepreneurship education is primarily for postsecondary level, including four-year colleges and adult education, but it can be adapted for special groups of vocational teacher education. The emphasis of the eight instructional units in Part III is operating a business. Unit G focuses on community relations. It…

  14. PACE. A Program for Acquiring Competence in Entrepreneurship. Part III: Being an Entrepreneur. Unit D: Marketing Management. Research and Development Series No. 194 C-4.

    Science.gov (United States)

    Ohio State Univ., Columbus. National Center for Research in Vocational Education.

    This three-part curriculum for entrepreneurship education is primarily for postsecondary level, including four-year colleges and adult education, but it can be adapted for special groups or vocational teacher education. The emphasis of the eight instructional units in Part III is operating a business. Unit D focuses on market management. It…

  15. A Population-Based Comparative Effectiveness Study of Radiation Therapy Techniques in Stage III Non-Small Cell Lung Cancer

    Energy Technology Data Exchange (ETDEWEB)

    Harris, Jeremy P. [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Murphy, James D. [Department of Radiation Medicine and Applied Science, University of California– San Diego, Moores Cancer Center, La Jolla, California (United States); Hanlon, Alexandra L. [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); University of Pennsylvania School of Nursing, Philadelphia, Pennsylvania (United States); Le, Quynh-Thu [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Stanford Cancer Institute, Stanford University School of Medicine, Stanford, California (United States); Loo, Billy W., E-mail: BWLoo@Stanford.edu [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Stanford Cancer Institute, Stanford University School of Medicine, Stanford, California (United States); Diehn, Maximilian, E-mail: diehn@Stanford.edu [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Stanford Cancer Institute, Stanford University School of Medicine, Stanford, California (United States); Institute for Stem Cell Biology and Regenerative Medicine, Stanford University School of Medicine, Stanford, California (United States)

    2014-03-15

    Purpose: Concerns have been raised about the potential for worse treatment outcomes because of dosimetric inaccuracies related to tumor motion and increased toxicity caused by the spread of low-dose radiation to normal tissues in patients with locally advanced non-small cell lung cancer (NSCLC) treated with intensity modulated radiation therapy (IMRT). We therefore performed a population-based comparative effectiveness analysis of IMRT, conventional 3-dimensional conformal radiation therapy (3D-CRT), and 2-dimensional radiation therapy (2D-RT) in stage III NSCLC. Methods and Materials: We used the Surveillance, Epidemiology, and End Results (SEER)-Medicare database to identify a cohort of patients diagnosed with stage III NSCLC from 2002 to 2009 treated with IMRT, 3D-CRT, or 2D-RT. Using Cox regression and propensity score matching, we compared survival and toxicities of these treatments. Results: The proportion of patients treated with IMRT increased from 2% in 2002 to 25% in 2009, and the use of 2D-RT decreased from 32% to 3%. In univariate analysis, IMRT was associated with improved overall survival (OS) (hazard ratio [HR] 0.90, P=.02) and cancer-specific survival (CSS) (HR 0.89, P=.02). After controlling for confounders, IMRT was associated with similar OS (HR 0.94, P=.23) and CSS (HR 0.94, P=.28) compared with 3D-CRT. Both techniques had superior OS compared with 2D-RT. IMRT was associated with similar toxicity risks on multivariate analysis compared with 3D-CRT. Propensity score matched model results were similar to those from adjusted models. Conclusions: In this population-based analysis, IMRT for stage III NSCLC was associated with similar OS and CSS and maintained similar toxicity risks compared with 3D-CRT.

  16. 17 CFR Table III to Subpart E of... - Civil Monetary Penalty Inflation Adjustments

    Science.gov (United States)

    2010-04-01

    ... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Civil Monetary Penalty Inflation Adjustments III Table III to Subpart E of Part 201 Commodity and Securities Exchanges SECURITIES..., Table III Table III to Subpart E of Part 201—Civil Monetary Penalty Inflation Adjustments U.S. Code...

  17. PACE. A Program for Acquiring Competence in Entrepreneurship. Part III: Being an Entrepreneur. Unit E: Successful Selling. Research and Development Series No. 194 C-5.

    Science.gov (United States)

    Ohio State Univ., Columbus. National Center for Research in Vocational Education.

    This three-part curriculum for entrepreneurship education is primarily for postsecondary level, including four-year colleges and adult education, but it can be adapted for special groups or vocational teacher education. The emphasis of the eight instructional units in Part III is operating a business. Unit E focuses on personal (face-to-face)…

  18. PACE. A Program for Acquiring Competence in Entrepreneurship. Part III: Being an Entrepreneur. Unit F: Managing Human Resources. Research and Development Series No. 194 C-6.

    Science.gov (United States)

    Ohio State Univ., Columbus. National Center for Research in Vocational Education.

    This three-part curriculum for entrepreneurship education is primarily for postsecondary level, including four-level colleges and adult education, but it can be adapted for special groups or vocational teacher education. The emphasis of the eight instructional units in Part III is operating a business. Unit F focuses on proper management of human…

  19. PACE. A Program for Acquiring Competence in Entrepreneurship. Part III: Being an Entrepreneur. Unit A: Managing the Business. Research and Development Series No. 194 C-1.

    Science.gov (United States)

    Ohio State Univ., Columbus. National Center for Research in Vocational Education.

    This three-part curriculum for entrepreneurship education is primarily for postsecondary level, including four-year colleges and adult education, but it can be adapted for special groups or vocational teacher education. The emphasis of the eight instructional units in Part III is operating a business. Unit A focuses on the management process. It…

  20. Determination of the NPP Krsko reactor core safety limits using the COBRA-III-C code

    International Nuclear Information System (INIS)

    Lajtman, S.; Feretic, D.; Debrecin, N.

    1989-01-01

    This paper presents the NPP Krsko reactor core safety limits determined by the COBRA-III-C code, along with the methodology used. The reactor core safety limits determination is a part of reactor protection limits procedure. The results obtained were compared to safety limits presented in NPP Krsko FSAR. The COBRA-III-C NPP Krsko design core steady state thermal hydraulics calculation, used as the basis for the safety limits calculation, is presented as well. (author)

  1. Nitrato-complexes of Y(III), La(III), Ce(III), Pr(III), Nd(III), Sm(III), Gd(III), Tb(III), Dy(III) and Ho(III) with 2-(2'-pyridyl) benzimidazole

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, A; Singh, M P; Singh, V K

    1982-05-01

    The nitrato-complexes, (Y(PyBzH)/sub 2/(NO/sub 3/)/sub 2/)NO/sub 3/.H/sub 2/O and Nd, Sm, Gd, Tb, Dy, Ho ; n=1-3, m=0-0.5 ; PyBzh=2-(2 -pyridyl)benzimidazole) are formed on interaction of the ligand with metal nitrates in ethanol. The electrical conductance values (116-129 ohm/sup -1/cm/sup 2/mol/sup -1/) suggest 1:1 electrolyte-nature of the complexes. Magnetic moment values of Ce(2.53 B.M.), Pr(3.62 B.M.), Nd(3.52 B.M.), Sm(1.70 B.M.), Gd(8.06 B.M.), Tb(9.44 B.M.), Dy(10.56 B.M.) and Ho(10.51 B.M.) in the complexes confirm the positive state of the metals. Infrared evidences are obtained for the existance of both coordinated (C/sub 2/v) and uncoordinated (D/sub 3/h) nitrate groups. Electronic absorption spectra of Pr(III)-, Nd(III)-, Sm(III)-, Tb(III)-, Dy(III)- and Ho(III)-complexes have been analysed in the light of LSJ terms.

  2. Nitrato-complexes of Y(III), La(III), Ce(III), Pr(III), Nd(III), Sm(III), Gd(III), Tb(III), Dy(III) and Ho(III) with 2-(2'-pyridyl) benzimidazole

    International Nuclear Information System (INIS)

    Mishra, A.; Singh, M.P.; Singh, V.K.

    1982-01-01

    The nitrato-complexes, [Y(PyBzH) 2 (NO 3 ) 2 ]NO 3 .H 2 O and Nd, Sm, Gd, Tb, Dy, Ho ; n=1-3, m=0-0.5 ; PyBzh=2-(2 -pyridyl)benzimidazole] are formed on interaction of the ligand with metal nitrates in ethanol. The electrical conductance values (116-129 ohm -1 cm 2 mol -1 ) suggest 1:1 electrolyte-nature of the complexes. Magnetic moment values of Ce(2.53 B.M.), Pr(3.62 B.M.), Nd(3.52 B.M.), Sm(1.70 B.M.), Gd(8.06 B.M.), Tb(9.44 B.M.), Dy(10.56 B.M.) and Ho(10.51 B.M.) in the complexes confirm the terpositive state of the metals. Infrared evidences are obtained for the existance of both coordinated (C 2 v) and uncoordinated (D 3 h) nitrate groups. Electronic absorption spectra of Pr(III)-, Nd(III)-, Sm(III)-, Tb(III)-, Dy(III)- and Ho(III)-complexes have been analysed in the light of LSJ terms. (author)

  3. Comparative analyses of the internal radiation exposures due to food chain pathway using food III code

    International Nuclear Information System (INIS)

    Choi, Yong Ho; Chung, Kyu Hoi; Kim, Jin Kyu; Lee, Jeong Ho

    1988-01-01

    In order to develop a food-chain computer code suitable to the environmental conditions of Korea, the FOOD III code was partially modified. The execution results for Korean male-adult were compared to those from the Canadian version of FOOD III to deduce a more realistic approach in dose assessment. The amounts of Mn-54, Co-50, Co-60, I-131 and I-132 released from Kori unit 1 in 1984 were used as the source terms for the sample calculation. The maximum atmospheric dispersion factor(X/Q) value on the site boundary was applied. Through the code modification, organ doses decreased by about 20∼70% and the effective committed dose equivalent by about 40% to be 7.935x10 -6 Sv/y which is 0.16% of the ICRP limit, 5x10 -3 Sv/y. (Author)

  4. A comparative study of boron and arsenic (III) rejection from brackish water by reverse osmosis membranes

    KAUST Repository

    Teychene, Benoî t; Collet, Gaelle; Gallard, Hervé ; Croue, Jean Philippe

    2013-01-01

    This study aims to compare at lab-scale the rejection efficiency of several reverse osmosis membranes (RO) toward arsenic (III) and boron during the filtration of a synthetic brackish water. The effect of pH and operating conditions on the rejection of each RO membrane was studied. Two types of membrane were investigated: "brackish water" and "sea water" membranes. Our results showed that the metalloid rejection depends on the membrane type, pH and transmembrane pressure applied. Increasing pH above the dissociation constant (pKa) of each specie improves significantly the metalloid rejection by RO membranes, whatever the membrane type. Moreover, at identical operating conditions (pH, transmembrane pressure), results showed that the brackish water membranes have a higher water flux and exhibit lower metalloid rejection. The highest As(III) rejection value for the tested brackish water membranes was 99% obtained at pH = 9.6 and 40 bars, whereas it was found that the sea water RO membranes could highly reject As(III), more than 99%, even at low pH and low pressure (pH = 7.6 and 24 bars).Regarding Boron rejection, similar conclusions could be drawn. The sea water RO membranes exert higher removal, with a high rejection value above 96% over the tested conditions. More generally, this study showed that, whatever the operating conditions or the tested membranes, the boron and As(III) permeate concentrations are below the WHO guidelines. In addition, new data about the boron and arsenic permeability of each tested RO membrane was brought thanks to a theoretical calculation. © 2012 Elsevier B.V.

  5. A comparative study of boron and arsenic (III) rejection from brackish water by reverse osmosis membranes

    KAUST Repository

    Teychene, Benoît

    2013-02-01

    This study aims to compare at lab-scale the rejection efficiency of several reverse osmosis membranes (RO) toward arsenic (III) and boron during the filtration of a synthetic brackish water. The effect of pH and operating conditions on the rejection of each RO membrane was studied. Two types of membrane were investigated: "brackish water" and "sea water" membranes. Our results showed that the metalloid rejection depends on the membrane type, pH and transmembrane pressure applied. Increasing pH above the dissociation constant (pKa) of each specie improves significantly the metalloid rejection by RO membranes, whatever the membrane type. Moreover, at identical operating conditions (pH, transmembrane pressure), results showed that the brackish water membranes have a higher water flux and exhibit lower metalloid rejection. The highest As(III) rejection value for the tested brackish water membranes was 99% obtained at pH = 9.6 and 40 bars, whereas it was found that the sea water RO membranes could highly reject As(III), more than 99%, even at low pH and low pressure (pH = 7.6 and 24 bars).Regarding Boron rejection, similar conclusions could be drawn. The sea water RO membranes exert higher removal, with a high rejection value above 96% over the tested conditions. More generally, this study showed that, whatever the operating conditions or the tested membranes, the boron and As(III) permeate concentrations are below the WHO guidelines. In addition, new data about the boron and arsenic permeability of each tested RO membrane was brought thanks to a theoretical calculation. © 2012 Elsevier B.V.

  6. Providing for energy efficiency in homes and small buildings. Part III. Determining which practices are most effective and installing materials

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-06-01

    The training program is designed to educate students and individuals in the importance of conserving energy and to provide for developing skills needed in the application of energy-saving techniques that result in energy-efficient buildings. A teacher guide and student workbook are available to supplement the basic manual. Subjects covered in Part III are: determining which practices are most efficient and economical; installing energy-saving materials; and improving efficiency of equipment.

  7. Comparison with experiment of COMETHE III-L fuel rod behaviour predictions

    International Nuclear Information System (INIS)

    Vliet, J. van; Billaux, M.

    1983-01-01

    A comparison is presented between experimental results and COMETHE III-L fuel rod behaviour predictions. The first part of the paper focuses on mechanical aspects, with as main experiments, AECL X-264 and Studsvik Interramp. The second part presents the results of a wide FGR benchmarking campaign, with a reference to previous COMETHE versions. It appears that the variance between experiment and calculation has decreased by a factor four when the III-J version was improved into the III-L version. As conclusion, some COMETHE III-L calculations are presented in order to illustrate its capability of predicting fuel rod performance limits. (author)

  8. Peroral endoscopic myotomy (POEM) vs laparoscopic Heller myotomy (LHM) for the treatment of Type III achalasia in 75 patients: a multicenter comparative study.

    Science.gov (United States)

    Kumbhari, Vivek; Tieu, Alan H; Onimaru, Manabu; El Zein, Mohammad H; Teitelbaum, Ezra N; Ujiki, Michael B; Gitelis, Matthew E; Modayil, Rani J; Hungness, Eric S; Stavropoulos, Stavros N; Shiwaku, Hiro; Kunda, Rastislav; Chiu, Philip; Saxena, Payal; Messallam, Ahmed A; Inoue, Haruhiro; Khashab, Mouen A

    2015-06-01

    Type III achalasia is characterized by rapidly propagating pressurization attributable to spastic contractions. Although laparoscopic Heller myotomy (LHM) is the current gold standard management for type III achalasia, peroral endoscopic myotomy (POEM) is conceivably superior because it allows for a longer myotomy. Our aims were to compare the efficacy and safety of POEM with LHM for type III achalasia patients. A retrospective study of 49 patients who underwent POEM for type III achalasia across eight centers were compared to 26 patients who underwent LHM at a single institution. Procedural data were abstracted and pre- and post-procedural symptoms were recorded. Clinical response was defined by improvement of symptoms and decrease in Eckardt stage to ≤ 1. Secondary outcomes included length of myotomy, procedure duration, length of hospital stay, and rate of adverse events. Clinical response was significantly more frequent in the POEM cohort (98.0 % vs 80.8 %; P = 0.01). POEM patients had significantly shorter mean procedure time than LHM patients (102 min vs 264 min; P myotomy (16 cm vs 8 cm; P myotomy than LHM, which may result in improved clinical outcomes. POEM appears to be an effective and safe alternative to LHM in patients with type III achalasia.

  9. Acuity and case management: a healthy dose of outcomes, part III.

    Science.gov (United States)

    Huber, Diane L; Craig, Kathy

    2007-01-01

    This is the third of a 3-part series presenting 2 effective applications--acuity and dosage--that describe how the business case for case management (CM) can be made. In Part I, dosage and acuity concepts were explained as client need-severity, CM intervention-intensity, and CM activity-dose prescribed by amount, frequency, duration, and breadth of activities. Concepts were presented that related the practice of CM to the use of evidence-based practice (EBP), knowledge, and methods and the development of instruments that measure and score pivotal CM actions. Part I also featured a specific exemplar, the CM Acuity Tool, and described how to use acuity to identify and score the complexity of a CM case. Part II further explained dosage and 2 acuity instruments, the Acuity Tool and AccuDiff. Part III presents linkage to EBP and practical applications. The information contained in the 3-part series applies to all CM practice settings and contains ideas and recommendations useful to CM generalists, specialists, supervisors, and business and outcomes managers. The Acuity Tools Project was developed from frontline CM practice in one large, national telephonic CM company. Dosage: A literature search failed to find research into dosage of a behavioral intervention. The Huber-Hall model was developed and tested in a longitudinal study of CM models in substance abuse treatment and reported in the literature. Acuity: A structured literature search and needs assessment launched the development of the suite of acuity tools. A gap analysis identified that an instrument to assign and measure case acuity specific to CM activities was needed. Clinical experts, quality specialists, and business analysts (n = 7) monitored the development and testing of the tools, acuity concepts, scores, differentials, and their operating principles and evaluated the validity of the acuity tools' content related to CM activities. During the pilot phase of development, interrater reliability testing of

  10. A Structural Molar Volume Model for Oxide Melts Part III: Fe Oxide-Containing Melts

    Science.gov (United States)

    Thibodeau, Eric; Gheribi, Aimen E.; Jung, In-Ho

    2016-04-01

    As part III of this series, the model is extended to iron oxide-containing melts. All available experimental data in the FeO-Fe2O3-Na2O-K2O-MgO-CaO-MnO-Al2O3-SiO2 system were critically evaluated based on the experimental condition. The variations of FeO and Fe2O3 in the melts were taken into account by using FactSage to calculate the Fe2+/Fe3+ distribution. The molar volume model with unary and binary model parameters can be used to predict the molar volume of the molten oxide of the Li2O-Na2O-K2O-MgO-CaO-MnO-PbO-FeO-Fe2O3-Al2O3-SiO2 system in the entire range of compositions, temperatures, and oxygen partial pressures from Fe saturation to 1 atm pressure.

  11. Comparative study of the influence of antimony oxide additives (III) and nickel hydroxide (II) on electrochemical behavior of cadmium electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Kadnikova, N.V.; Lvova, L.A.; Ryabskaya, I.A.

    1983-01-01

    Comparative study of the influence of additives indicated that with partial or complete replacement in the active mass of the cadmium electrode of nickel hydroxide (II) by antimony oxide (III), the electrochemical characteristics do not significantly change. During prolonged storage of charged cadmium electrodes the presence of nickel hydroxide (II) and intermetal compound (IMC) of cadmium with nickel is formed and the specific surface increases. In the case of adding antimony (III) formation of noticeable quantities of IMC of cadmium with antimony is not observed. The specific surface is reduced during storage.

  12. Comparing a combination of validated questionnaires and level III portable monitor with polysomnography to diagnose and exclude sleep apnea.

    Science.gov (United States)

    Pereira, Effie J; Driver, Helen S; Stewart, Steven C; Fitzpatrick, Michael F

    2013-12-15

    Questionnaires have been validated as screening tools in adult populations at risk for obstructive sleep apnea (OSA). Portable monitors (PM) have gained acceptance for confirmation of OSA in some patients with a high pretest probability of the disorder. We evaluated the combined diagnostic utility of 3 validated questionnaires and a Level III PM in the diagnosis and exclusion of OSA, as compared with in-laboratory polysomnography (PSG) derived apnea hypopnea index (AHI). Consecutive patients referred to the Sleep Disorders Clinic completed 3 testing components: (1) 3 questionnaires (Berlin, STOP-Bang, and Sleep Apnea Clinical Score [SACS]); (2) Level III at-home PM (MediByte) study; and (3) Level I in-laboratory PSG. The utility of individual questionnaires, the Level III device alone, and the combination of questionnaires and the Level III device were compared with the PSG. One hundred twenty-eight patients participated in the study (84M, 44F), mean ± SD age 50 ± 12.3years, BMI 31 ± 6.6 kg/m(2). At a PSG threshold AHI = 10, the PM derived respiratory disturbance index (RDI) had a sensitivity and specificity of 79% and 86%, respectively. The sensitivity and specificity for the other screening tools were: Berlin 88%, 25%; STOP-Bang 90%, 25%; SACS 33%, 75%. The sensitivity and specificity at a PSG AHI = 15 were: PM 77%, 95%; Berlin 91%, 28%; STOP-Bang 93%, 28%; SACS 35%, 78%. Questionnaires alone, possibly given a reliance on sleepiness as a symptom, cannot reliably rule out the presence of OSA. Objective physiological measurement is critical for the diagnosis and exclusion of OSA.

  13. Comparative genomic analysis of the WRKY III gene family in populus, grape, arabidopsis and rice.

    Science.gov (United States)

    Wang, Yiyi; Feng, Lin; Zhu, Yuxin; Li, Yuan; Yan, Hanwei; Xiang, Yan

    2015-09-08

    WRKY III genes have significant functions in regulating plant development and resistance. In plant, WRKY gene family has been studied in many species, however, there still lack a comprehensive analysis of WRKY III genes in the woody plant species poplar, three representative lineages of flowering plant species are incorporated in most analyses: Arabidopsis (a model plant for annual herbaceous dicots), grape (one model plant for perennial dicots) and Oryza sativa (a model plant for monocots). In this study, we identified 10, 6, 13 and 28 WRKY III genes in the genomes of Populus trichocarpa, grape (Vitis vinifera), Arabidopsis thaliana and rice (Oryza sativa), respectively. Phylogenetic analysis revealed that the WRKY III proteins could be divided into four clades. By microsynteny analysis, we found that the duplicated regions were more conserved between poplar and grape than Arabidopsis or rice. We dated their duplications by Ks analysis of Populus WRKY III genes and demonstrated that all the blocks were formed after the divergence of monocots and dicots. Strong purifying selection has played a key role in the maintenance of WRKY III genes in Populus. Tissue expression analysis of the WRKY III genes in Populus revealed that five were most highly expressed in the xylem. We also performed quantitative real-time reverse transcription PCR analysis of WRKY III genes in Populus treated with salicylic acid, abscisic acid and polyethylene glycol to explore their stress-related expression patterns. This study highlighted the duplication and diversification of the WRKY III gene family in Populus and provided a comprehensive analysis of this gene family in the Populus genome. Our results indicated that the majority of WRKY III genes of Populus was expanded by large-scale gene duplication. The expression pattern of PtrWRKYIII gene identified that these genes play important roles in the xylem during poplar growth and development, and may play crucial role in defense to drought

  14. The removal of toxic metals from liquid effluents by ion exchange resins. Part IV: Chromium(III)/H+ /Lewatit SP112; La eliminación de metales tóxicos presentes en efluentes líquidos mediante resinas de cambio iónico. Parte IV: cromo(III)/H+/Lewatit SP112

    Energy Technology Data Exchange (ETDEWEB)

    Alguacil, F.J.

    2017-09-01

    This investigation presented results on the removal of chromium(III), from aqueous solution in the 0-5 pH range, using Lewatit SP112 cationic exchange resin. Several aspects affecting the ion exchange process were evaluated, including: the influence of the stirring speed, temperature, pH of the solution, resin dosage and aqueous ionic strength. The selectivity of the system was tested against the presence of other metals in the aqueous solution, whereas the removal of chromium(III) from solutions was compared with results obtained using multiwalled carbon nanotubes as adsorbents. From the batch experimental data, best fit of the results is obtained with the Langmuir model, whereas the ion exchange process is best explained by the pseudo-second order model, moreover, experimental data responded well to the film-diffusion controlled model. Elution of the chromium(III) loaded into the resin is well accomplished by the use of sodium hydroxide solutions. [Spanish] En este trabajo se presentan los resultados obtenidos en la eliminación de cromo(III) de disoluciones acuosas (pH 0-5) mediante la resina de intercambio catiónico Lewatit SP112. Se han investigado algunas variables que pueden afectar al sistema: influencia de la agitación, temperatura, pH y fuerza iónica del medio acuoso y cantidad de resina; también se ha investigado acerca de la selectividad del sistema cuando otros metales están presentes en el medio acuoso, comparándose los resultados de la eliminación del cromo(III) usando la resina con los resultados obtenidos cuando se emplea otro adsorbente como son los nanotubos de carbono de pared múltiple. Los resultados experimentales indican que la carga del cromo(III) en la resina responde mejor al modelo de Langmuir, mientras que los modelos cinéticos indican que la carga del metal en la resina responde al modelo de pseudo-segundo orden y difusión en la capa límite. La elución del cromo(III) se realiza con disoluciones de hidróxid.

  15. Insight into the Extraction Mechanism of Americium(III) over Europium(III) with Pyridylpyrazole: A Relativistic Quantum Chemistry Study.

    Science.gov (United States)

    Kong, Xiang-He; Wu, Qun-Yan; Wang, Cong-Zhi; Lan, Jian-Hui; Chai, Zhi-Fang; Nie, Chang-Ming; Shi, Wei-Qun

    2018-05-10

    Separation of trivalent actinides (An(III)) and lanthanides (Ln(III)) is one of the most important steps in spent nuclear fuel reprocessing. However, it is very difficult and challenging to separate them due to their similar chemical properties. Recently the pyridylpyrazole ligand (PypzH) has been identified to show good separation ability toward Am(III) over Eu(III). In this work, to explore the Am(III)/Eu(III) separation mechanism of PypzH at the molecular level, the geometrical structures, bonding nature, and thermodynamic behaviors of the Am(III) and Eu(III) complexes with PypzH ligands modified by alkyl chains (Cn-PypzH, n = 2, 4, 8) have been systematically investigated using scalar relativistic density functional theory (DFT). According to the NBO (natural bonding orbital) and QTAIM (quantum theory of atoms in molecules) analyses, the M-N bonds exhibit a certain degree of covalent character, and more covalency appears in Am-N bonds compared to Eu-N bonds. Thermodynamic analyses suggest that the 1:1 extraction reaction, [M(NO 3 )(H 2 O) 6 ] 2+ + PypzH + 2NO 3 - → M(PypzH)(NO 3 ) 3 (H 2 O) + 5H 2 O, is the most suitable for Am(III)/Eu(III) separation. Furthermore, the extraction ability and the Am(III)/Eu(III) selectivity of the ligand PypzH is indeed enhanced by adding alkyl-substituted chains in agreement with experimental observations. Besides this, the nitrogen atom of pyrazole ring plays a more significant role in the extraction reactions related to Am(III)/Eu(III) separation compared to that of pyridine ring. This work could identify the mechanism of the Am(III)/Eu(III) selectivity of the ligand PypzH and provide valuable theoretical information for achieving an efficient Am(III)/Eu(III) separation process for spent nuclear fuel reprocessing.

  16. The removal of toxic metals from liquid effluents by ion exchange resins. Part IV: Chromium(III)/H+ /Lewatit SP112

    International Nuclear Information System (INIS)

    Alguacil, F.J.

    2017-01-01

    This investigation presented results on the removal of chromium(III), from aqueous solution in the 0-5 pH range, using Lewatit SP112 cationic exchange resin. Several aspects affecting the ion exchange process were evaluated, including: the influence of the stirring speed, temperature, pH of the solution, resin dosage and aqueous ionic strength. The selectivity of the system was tested against the presence of other metals in the aqueous solution, whereas the removal of chromium(III) from solutions was compared with results obtained using multiwalled carbon nanotubes as adsorbents. From the batch experimental data, best fit of the results is obtained with the Langmuir model, whereas the ion exchange process is best explained by the pseudo-second order model, moreover, experimental data responded well to the film-diffusion controlled model. Elution of the chromium(III) loaded into the resin is well accomplished by the use of sodium hydroxide solutions. [es

  17. Oral Assessment Kit, Levels II & III. Draft.

    Science.gov (United States)

    Agrelo-Gonzalez, Maria; And Others

    The assessment packet includes a series of oral tests to help develop speaking as an integral part of second language instruction at levels II and III. It contains: 8 mini-tests for use at level II; 9 mini-tests for use at level III; a rating scale and score sheet masters for evaluating performance on these tests; and a collection of suggested…

  18. Kinetics of Cr(III) and Cr(VI) removal from water by two floating macrophytes.

    Science.gov (United States)

    Maine, M A; Hadad, H R; Sánchez, G; Caffaratti, S; Pedro, M C

    2016-01-01

    The aim of this work was to compare Cr(III) and Cr(VI) removal kinetics from water by Pistia stratiotes and Salvinia herzogii. The accumulation in plant tissues and the effects of both Cr forms on plant growth were also evaluated. Plants were exposed to 2 and 6 mg L(-1) of Cr(III) or Cr(VI) during 30 days. At the end of the experiment, Cr(VI) removal percentages were significantly lower than those obtained for Cr(III) for both macrophytes. Cr(III) removal kinetics involved a fast and a slow component. The fast component was primarily responsible for Cr(III) removal while Cr(VI) removal kinetics involved only a slow process. Cr accumulated principally in the roots. In the Cr(VI) treatments a higher translocation from roots to aerial parts than in Cr(III) treatments was observed. Both macrophytes demonstrated a high ability to remove Cr(III) but not Cr(VI). Cr(III) inhibited the growth at the highest studied concentration of both macrophytes while Cr(VI) caused senescence. These results have important implications in the use of constructed wetlands for secondary industrial wastewater treatment. Common primary treatments of effluents containing Cr(VI) consists in its reduction to Cr(III). Cr(III) concentrations in these effluents are normally below the highest studied concentrations in this work.

  19. Thermal sensation and comfort models for non-uniform and transient environments, part III: Whole-body sensation and comfort

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Hui; Arens, Edward; Huizenga, Charlie [Center for the Built Environment, UC Berkeley (United States); Han, Taeyoung [General Motors Company (United States)

    2010-02-15

    A three-part series presents the development of models for predicting the local thermal sensation (Part I) and local thermal comfort (Part II) of different parts of the human body, and also the whole-body sensation and comfort (Part III) that result from combinations of local sensation and comfort. The models apply to sedentary activities in a range of environments: uniform and non-uniform, stable and transient. They are based on diverse findings from the literature and from body-part-specific human subject tests in a climate chamber. They were validated against a test of automobile passengers. The series is intended to present the models' rationale, structure, and coefficients, so that others can test them and develop them further as additional empirical data becomes available. A) The whole-body (overall) sensation model has two forms, depending on whether all of the body's segments have sensations effectively in the same direction (e.g warm or cool), or whether some segments have sensations opposite to those of the rest of the body. For each, individual body parts have different weights for warm versus cool sensations, and strong local sensations dominate the overall sensation. If all sensations are near neutral, the overall sensation is close to the average of all body sensations. B) The overall comfort model also has two forms. Under stable conditions, people evaluate their overall comfort by a complaint-driven process, meaning that when two body parts are strongly uncomfortable, no matter how comfortable the other body parts might be, the overall comfort will be near the discomfort level of the two most uncomfortable parts. When the environmental conditions are transient, or people have control over their environments, overall comfort is better than that of the two most uncomfortable body parts. This can be accounted for by adding the most comfortable vote to the two most uncomfortable ones. (author)

  20. 'Americium(III)/trivalent lanthanides' separation using organothiophosphinic acids

    International Nuclear Information System (INIS)

    Hill, C.; Madic, C.; Baron, P.; Ozawa, Masaki; Tanaka, Yasumasa.

    1997-01-01

    The present paper describes the extraction of neodymium and other lanthanides by saponified Cyanex 301 acid. The saponification of commercial Cyanex 301 acid favoured the extraction of macro concentrations of neodymium from sodium nitrate aqueous solutions (pH eq ∼ 4). The amount of lanthanide extracted in the organic phase always reached the third of the initial concentration of saponified Cyanex 301 acid, which assumed a cation exchange mechanism to occur during the extraction. No nitrate anion took part in the complex formation. This paper also compares the abilities of purified Cyanex 301, Cyanex 302 and Cyanex 272 acids to extract and separate 241 Am(III) from 152 Eu(III). Very high separation factors S.F. Am/Eu were observed in the case of purified Cyanex 301 acid. Finally some studies are presented herein using tri-n-butylphosphate (TBP) as a synergistic extractant with Cyanex 301 acid to separate actinides from trivalent lanthanide. (author)

  1. LHC Beam Dump Design Study - Part III : Off-normal operating conditions

    CERN Document Server

    Bruno, L; Ross, M; Sala, P

    2000-01-01

    The LHC beam dump design study has been preliminarily substantiated by energy deposition simulations (Part I) and heat transfer analyses (Part II). The present report is devoted to the abnormal operating conditions induced by a malfunction of the beam diluters. A general approach to the analysis of off-normal operation is presented, which is derived from standard design norms adopted in the nuclear industry. Attention is focused mainly on the carbon core, which is longitudinally split into segments of different density in order to better distribute the deposited energy. The maximum energy density it absorbs decreases by at least 33%, compared to a uniform standard density carbon core. This structure may sustain any partial sweep failure without major damage, up to the ultimate beam intensity and energy. To minimise the risks inherent in a fully unswept beam, a sacrificial graphite mandrel will be placed on the core axis, surrounded by a thick high strength carbon-carbon composite tube. With this arrangement, ...

  2. Comparative study on the treatment of Rockwood type III acute acromioclavicular dislocation: Clinical results from the TightRope® technique vs. K-wire fixation.

    Science.gov (United States)

    Horst, K; Garving, C; Thometzki, T; Lichte, P; Knobe, M; Dienstknecht, T; Hofman, M; Pape, H-C

    2017-04-01

    The aim of this study was to address the inconsistency regarding the operative treatment of Rockwood type III acromioclavicular joint separation. We compared results after single- and double TightRope ® reduction with results after acromioclavicular transfixation via K-wires only and additional ligament augmentation in acute acromioclavicular (AC) joint separations graded Rockwood type III, and hypothesized that the TightRope ® technique leads to better clinical and radiological results. We conducted a retrospective clinical cohort study and included 42 consecutive patients (mean age 43 years [24-66]) diagnosed and operatively treated between 2004 and 2012 (mean follow-up was 54.6 months [15-118]). Specific shoulder scores as well as scores reflecting the patients' overall mental and physical health status were used. Radiological evaluation was also performed. The SF12 test revealed comparability between all subgroups. Specific shoulder tests and a visual analogue scale demonstrated comparable results. Radiographic measurements showed a significant reduction in the AC distance and CC distance after surgery in all subgroups. The early complication rate was 9.5% for all patients, while late complications occurred in 14.3% of all cases. Compared to the established methods, the operative TightRope ® procedures represent a safe alternative in Rockwood III injuries. All investigated techniques predominantly led to good and excellent clinical results in acute Rockwood type III AC joint instabilities. Avoidance of material removal and shorter hospital stays appear to speak in favour for the TightRope ® technique. IV. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

  3. Spectroscopic studies on the interaction of europium(III) and curium(III) with components of the human mucosa

    Energy Technology Data Exchange (ETDEWEB)

    Wilke, Claudia; Barkleit, Astrid [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Chemistry of the F-Elements

    2016-07-01

    To evaluate the health risks of lanthanides (Ln) and radiotoxic actinides (An) in case of ingestion accidents etc., investigations into the chemical reactions of these metals in the human gastrointestinal tract are necessary. Our previous study revealed that mucin, an important part of the protective mucosa layer in the digestive system, shows a strong interaction with Eu(III). Based on these results, the present study focuses on the components of this glycoprotein and identified N-acetylneuraminic acid (NANA) as the dominant binding carbohydrate of mucin. TRLFS measurements suggest the formation of a 1: 1 complex with log β of 3.2 ± 0.1 for Eu(III) and 3.3 ± 0.1 for Cm(III), respectively.

  4. Rethinking ASME III seismic analysis for piping operability evaluations

    International Nuclear Information System (INIS)

    Adams, T.M.; Stevenson, J.D.

    1994-01-01

    It has been recognized since the mid 1980's that there are very large seismic margins to failure for nuclear piping systems when designed using current industry practice, design criteria, and methods. As a result of this realization there are or have been approximately eighteen initiatives within the ASME , Boiler and Pressure Vessel Code Section III, Division 1, in the form of proposed code cases and proposed code text changes designed to reduce these failure margins to more realistic values. For the most part these initiatives have concentrated on reclassifying seismic inertia stresses in the piping as secondary and increasing the allowable stress limits permitted by Section III of the ASME, Boiler Code. This paper focuses on the application of non-linear spectral analysis methods as a method to reduce the input seismic demand determination and thereby reduce the seismic failure margins. The approach is evaluated using the ASME Boiler Pressure Vessel Code Section III Subgroup on Design benchmark procedure as proposed by the Subgroup's Special Task Group on Integrated Piping Criteria. Using this procedure, criteria are compared to current code criterion and analysis methods, and several other of the currently proposed Boiler and Pressure Vessel, Section III, changes. Finally, the applicability of the non-linear spectral analysis to continued Safe Operation Evaluations is reviewed and discussed

  5. Irradiated uranium reprocessing, Final report - I-IV, Part III

    International Nuclear Information System (INIS)

    Gal, I.

    1961-12-01

    This third part of the final report include the following: Annex 5 - device for opening the cover; Annex 6 - inner part of the device for sampling of the radioactive solution; Annex 7 - outer part of the device for sampling of the radioactive solution; Annex 8 - pneumatic taps [sr

  6. Isothiocyanato complexes of Gd(III), Tb(III), Dy(III) and Ho(III) with 2-(2'-pyridyl)benzimidazole

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, A; Singh, V K

    1982-01-01

    Six-coordinated complexes of the type (Ln(PyBzH)/sub 2/NCS.H/sub 2/O) (NCS)/sub 2/.nH/sub 2/O/mC/sub 2/H/sub 5/OH (Ln = Gd(III), Tb(III), Dy(III) and Ho(III), n=1-2; m=1) have been prepared from Ln(NCS)/sub 6//sup 3 -/. The room temperature magnetic moment values confirm the terpositive state of the lanthanide ions. Infrared spectra suggest the N-coordination of thiocyanate group. Electronic spectral studies of Tb(III), Dy(III) and Ho(III) complexes have been made in terms of LSJ term energies. 13 refs.

  7. Proceedings of the Annual Meeting of the Association for Education in Journalism and Mass Communication (83rd, Phoenix, Arizona, August 9-12, 2000). Miscellaneous, Part III.

    Science.gov (United States)

    Association for Education in Journalism and Mass Communication.

    The Miscellaneous, part III section of the proceedings contains the following 11 papers: "The Relationship between Health and Fitness Magazine Reading and Eating-Disordered Weight-Loss Methods among High School Girls" (Steven R. Thomsen, Michelle M. Weber, and Lora Beth Brown); "A Practical Exercise for Teaching Ethical Decision…

  8. A Randomized Controlled Trial Comparing Suture-Fixation Mucopexy and Doppler-Guided Hemorrhoidal Artery Ligation in Patients with Grade III Hemorrhoids

    Directory of Open Access Journals (Sweden)

    Min Zhai

    2016-01-01

    Full Text Available Background. We aimed to evaluate the effectiveness of a suture-fixation mucopexy procedure by comparing with Doppler-guided hemorrhoidal artery ligation (DGHAL in the management of patients with grade III hemorrhoids. Methods. This was a randomized controlled trial. One hundred patients with grade III hemorrhoids were randomly assigned to receive suture-fixation mucopexy (n=50 or DGHAL (n=50. Outcome assessments were performed at 2 weeks, 12 months, and 24 months. Assessments included resolution of clinical symptoms, postoperative complications, duration of hospitalization, and total costs. Results. At 2 weeks, one (2% patient in suture-fixation group and four (8% patients in DGHAL group had persistent prolapsing hemorrhoids. Postoperative bleeding was observed in two patients (4% in suture-fixation group and one patient in DGHAL group. There was no significant difference in short-term recurrence between groups. Postoperative complications and duration of hospitalization were comparable between the two groups. Rates of recurrence of prolapse or bleeding at 12 months did not differ between groups. However, recurrence of prolapse at 24 months was significantly more common in DGHAL group (19.0% versus 2.3%, p=0.030. Conclusions. Compared with DGHAL, the suture-fixation mucopexy technique had comparable short-term outcomes and favorable long-term outcomes.

  9. Radiation protection in category III large gamma irradiators; Radioprotecao em irradiadores de grande porte de categoria III

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Neivaldo; Furlan, Gilberto Ribeiro, E-mail: neivaldo@cena.usp.b, E-mail: gilfurlan@cena.usp.b [Centro de Energia Nuclear na Agricultura (CENA/USP), Piracicaba, SP (Brazil); Itepan, Natanael Marcio, E-mail: natanael.itepan@unianhanguera.edu.b [Universidade Anhanguera, Goiania, GO (Brazil)

    2011-07-01

    This article discusses the advantages of category III large gamma irradiator compared to the others, with emphasis on aspects of radiological protection, in the industrial sector. This category is a kind of irradiators almost unknown to the regulators authorities and the industrial community, despite its simple construction and greater radiation safety intrinsic to the model, able to maintain an efficiency of productivity comparable to those of category IV. Worldwide, there are installed more than 200 category IV irradiators and there is none of a category III irradiator in operation. In a category III gamma irradiator, the source remains fixed in the bottom of the tank, always shielded by water, negating the exposition risk. Taking into account the benefits in relation to radiation safety, the category III large irradiators are highly recommended for industrial, commercial purposes or scientific research. (author)

  10. Effect of Eu(III) on the degradation of malic acid by Pseudomonas fluorescens

    International Nuclear Information System (INIS)

    Nankawa, T.; Ozaki, T.; Ohnuki, T.; Suzuki, Y.; Francis, A.J.

    2005-01-01

    Full text of publication follows: The transuranic elements, such as Am(III) and Cm(III), are highly toxic because they emit high-energy α particles and have long half-lives. To estimate their long-term environmental behavior, we need to elucidate degradation of actinide-organic complexes by microorganisms. We studied the biodegradation of Eu(III)-malic acid complexes by Pseudomonas fluorescens. Malic acid is ubiquitous in the environment and is one of the microbial metabolites that is part of the tri-carboxylic acid (TCA) cycle. Europium(III) is a good analogue for Am(III) and Cm(III). To investigate the effect of Eu(III) on the degradation of malic acid by P. fluorescens, we compared the degradation behavior of Eu(III)-malic acid complexes to that of Fe(III) and Al(III)-malic acid complexes. In the medium containing 1 mM malic acid and 0-0.5 mM Fe(III), malic acid was degraded completely. In the medium containing 1 mM malic acid and 0.05-0.5 mM Al(III), malic acid was degraded until the concentration of malic acid became equal to that of Al(III), indicating that Al(III)-malic acid complex with 1: 1 molar ratio was recalcitrant to biodegradation. In the medium containing 1 mM malic acid and 0.05-0.5 mM Eu(III), degradation of malic acid was not observed. The effect of metals on degradation of malic acid was in the order of Fe(III) < Al(III) < Eu(III). The stability constants of 1:1 Fe(III)-, Al(III)-, and Eu(III)-malic acid complexes are 7.1, 4.6, and 4.9, respectively. These results indicate that degradability of malic acid does not depend on the stability constants of metal-malic acid complexes. We found that 10 mM malic acid was degraded in the presence of 0.05 and 0.1 mM Eu(III) but 1 mM malic acid was not degraded in the presence of 0.05 and 0.1 mM Eu(III). The degradation rate of malic acid increased with a decreasing ratio of Eu(III) to malic acid. (authors)

  11. Complexation of trivalent actinides and lanthanides with hydrophilic N-donor ligands for Am(III)/Cm(III) and An(III)/Ln(III) separation; Komplexierung von trivalenten Actiniden und Lanthaniden mit hydrophilen N-Donorliganden zur Am(III)/Cm(III)- bzw. An(III)/Ln(III)-Trennung

    Energy Technology Data Exchange (ETDEWEB)

    Wagner, Christoph

    2017-07-24

    The implementation of actinide recycling processes is considered in several countries, aiming at the reduction of long-term radiotoxicity and heat load of used nuclear fuel. This requires the separation of the actinides from the fission and corrosion products. The separation of the trivalent actinides (An(III)) Am(III) and Cm(III), however, is complicated by the presence of the chemically similar fission lanthanides (Ln(III)). Hydrophilic N-donor ligands are employed as An(III) or Am(III) selective complexing agents in solvent extraction to strip An(III) or Am(III) from an organic phase loaded with An(III) and Ln(III). Though they exhibit excellent selectivity, the complexation chemistry of these ligands and the complexes formed during solvent extraction are not sufficiently characterized. In the present thesis the complexation of An(III) and Ln(III) with hydrophilic N-donor ligands is studied by time resolved laser fluorescence spectroscopy (TRLFS), UV/Vis, vibronic sideband spectroscopy and solvent extraction. TRLFS studies on the complexation of Cm(III) and Eu(III) with the Am(III) selective complexing agent SO{sub 3}-Ph-BTBP (tetrasodium 3,3{sup '},3'',3{sup '''}-([2,2{sup '}-bipyridine]-6,6{sup '}-diylbis(1,2,4-triazine-3,5,6-triyl)) tetrabenzenesulfonate) revealed the formation of [M(SO{sub 3}-Ph-BTBP){sub n}]{sup (4n-3)-} complexes (M = Cm(III), Eu(III); n = 1, 2). The conditional stability constants were determined in different media yielding two orders of magnitude larger β{sub 2}-values for the Cm(III) complexes, independently from the applied medium. A strong impact of ionic strength on the stability and stoichiometry of the formed complexes was identified, resulting from the stabilization of the pentaanionic [M(SO{sub 3}-Ph-BTBP){sub 2}]{sup 5-} complex with increasing ionic strength. Thermodynamic studies of Cm(III)-SO{sub 3}-Ph-BTBP complexation showed that the proton concentration of the applied medium impacts

  12. La moisson des Argonautiques et la poétique d’Apollonios dans le chant III Harvesting in Argonautica and Apollonios' poetics in book III La mietitura delle Argonautiche e la poetica di Apollonio nel canto III

    Directory of Open Access Journals (Sweden)

    Françoise Létoublon

    2013-05-01

    Full Text Available Un’analisi comparativa dei paragoni presenti nel canto III delle Argonautiche e di quelli omerici mostra che Apollonio s’ispira fortemente ai suoi modelli, in modo particolare nella forma ed nel lessico. Eppure, nella maggior parte dei casi, egli porta i confronti omerici lontano dal loro contesto d’origine per adattarli ai suoi intenti. Nella prima parte del canto III, i similitudini rispondono alla volontà comune di evidenziare le pene che l’amore suscita nell’animo e nel comportamento di Medea. Nella seconda parte, le prove che Giasone deve superare danno luogo, in modo sorprendente, ad immagini guerriere funzionali alla descrizione dei preparativi, ma in seguito Apollonio ricorre ad un lessico artigianale ed agricolo per evocare dei compiti che consistono effettivamente nell’aggiogare e tirare una coppia di tori, in un’aratura, in una semina ed in una mietitura. L’aspetto più notevole è che molti paragoni riuniti verso la fine del canto non sembrano trovare un corrispondente in alcun modello omerico, come se il racconto di questa prova inedita avesse progressivamente liberato Apollonio dalla sua dipendenza da Omero.A detailed survey of the similes in Argonautica III, compared to the Homeric similes, shows that Apollonius very largely draws his inspiration from his models, mainly in the form and the words. However, he shifts the Homeric similes away from their original context to re-model them to his personal intention. In the first part of book III, the similes follow a common desire to show how many troubles love provokes in Medea’s soul and behaviour. In the second part, Jason’s ordeals provide the occasion for war images describing the preparation of the hero, but thereafter Apollonius resorts to a craftsmanship and agricultural register for evoking tasks that actually consist of hitching up, ploughing, sowing and harvesting. The most remarkable fact is that some comparisons grouped near the end of the book seem

  13. Complexes of 4-chlorophenoxyacetates of Nd(III), Gd(III) and Ho(III)

    International Nuclear Information System (INIS)

    Ferenc, W.; Bernat, M; Gluchowska, H.W.; Sarzynski, J.

    2010-01-01

    The complexes of 4-chlorophenoxyacetates of Nd(III), Gd(III) and Ho(III) have been synthesized as polycrystalline hydrated solids, and characterized by elemental analysis, spectroscopy, magnetic studies and also by X-ray diffraction and thermogravimetric measurements. The analysed complexes have the following colours: violet for Nd(III), white for Gd(III) and cream for Ho(III) compounds. The carboxylate groups bind as bidentate chelating (Ho) or bridging ligands (Nd, Gd). On heating to 1173K in air the complexes decompose in several steps. At first, they dehydrate in one step to form anhydrous salts, that next decompose to the oxides of respective metals. The gaseous products of their thermal decomposition in nitrogen were also determined and the magnetic susceptibilities were measured over the temperature range of 76-303K and the magnetic moments were calculated. The results show that 4-chlorophenoxyacetates of Nd(III), Gd(III) and Ho(III) are high-spin complexes with weak ligand fields. The solubility value in water at 293K for analysed 4-chlorophenoxyacetates is in the order of 10 -4 mol/dm 3 . (author)

  14. Gd(III)-nanodiamond conjugates for MRI contrast enhancement

    Science.gov (United States)

    Manus, Lisa M.; Mastarone, Daniel J.; Waters, Emily A.; Zhang, Xue-Qing; Schultz-Sikma, Elise A.; MacRenaris, Keith W.; Ho, Dean

    2010-01-01

    A Gd(III)-nanodiamond conjugate [Gd(III)-ND] was prepared and characterized, enabling detection of nanodiamonds by MR imaging. The Gd(III)-ND particles significantly reduced the T1 of water protons with a per-Gd(III) relaxivity of 58.82 ± 1.18 mM−1s−1 at 1.5 Tesla (60 MHz). This represents a tenfold increase compared to the monomer Gd(III) complex (r1 = 5.42 ± 0.20 mM−1s−1) and is among the highest per-Gd(III) relaxivities reported. PMID:20038088

  15. NMR and TRLFS studies of Ln(iii) and An(iii) C5-BPP complexes.

    Science.gov (United States)

    Adam, Christian; Beele, Björn B; Geist, Andreas; Müllich, Udo; Kaden, Peter; Panak, Petra J

    2015-02-01

    C5-BPP is a highly efficient N-donor ligand for the separation of trivalent actinides, An(iii), from trivalent lanthanides, Ln(iii). The molecular origin of the selectivity of C5-BPP and many other N-donor ligands of the BTP-type is still not entirely understood. We present here the first NMR studies on C5-BPP Ln(iii) and An(iii) complexes. C5-BPP is synthesized with 10% 15 N labeling and characterized by NMR and LIFDI-MS methods. 15 N NMR spectroscopy gives a detailed insight into the bonding of C5-BPP with lanthanides and Am(iii) as a representative for trivalent actinide cations, revealing significant differences in 15 N chemical shift for coordinating nitrogen atoms compared to Ln(iii) complexes. The temperature dependence of NMR chemical shifts observed for the Am(iii) complex indicates a weak paramagnetism. This as well as the observed large chemical shift for coordinating nitrogen atoms show that metal-ligand bonding in Am(C5-BPP) 3 has a larger share of covalence than in lanthanide complexes, confirming earlier studies. The Am(C5-BPP) 3 NMR sample is furthermore spiked with Cm(iii) and characterized by time-resolved laser fluorescence spectroscopy (TRLFS), yielding important information on the speciation of trace amounts of minor complex species.

  16. Articulación de fones en individuos clase esqueletal I,II y III Speech patterns in skeletal class I, II and III subjects

    Directory of Open Access Journals (Sweden)

    Pía Villanueva

    2009-09-01

    Full Text Available OBJETIVO: determinar los patrones de articulación de fones consonánticos en sujetos de habla española chilena clases I, II y III esqueletal; comparar las diferencias fonéticas que existan entre clases esqueletales. MÉTODOS: se seleccionaron 54 individuos que cumplían con los criterios de inclusión determinados mediante un examen clínico intraoral y a través del análisis de Ricketts, y se conformaron los grupos de estudio de pacientes clases esqueletales I, II y III. Se les realizó un examen fonoarticulatorio estandarizado para determinar los fones modificados y el patrón articulatorio compensatorio realizado. RESULTADOS: se observaron cambios en el punto de articulación de fones consonánticos en las tres clases esqueletales, con diferencias significativas en los grupos de fones anteriores y medios entre pacientes clases I y II, sólo en el grupo de los fones anteriores entre pacientes I y III. Entre pacientes clases II y III no se observaron diferencias significativas. Se reportan modificaciones y compensaciones cualitativamente distintas entre las clases esqueletales. CONCLUSIONES: en relación a pacientes clase I, los pacientes clase II o III, presentan distinto grado de modificación en el punto de articulación de fones consonánticos. Las diferencias observadas se relacionan con los patrones esqueletales propios de cada clase.PURPOSE: to determine the consonant phonemes articulation patterns in Chilean skeletal class I, II and III Spanish speakers and compare their phonetic differences. METHODS: fifty-four skeletal class I, II and III subjects were selected, based on intraoral clinical examination and Ricketts cephalometric analysis, constituting the study groups. A standardized phonoarticulatory test was applied to each patient to determine the modified phonemes and their compensatory patterns. RESULTS: the findings indicate changes in articulation in all three groups. Significant differences were found in anterior and medium

  17. Bioaccumulation and subcellular partitioning of Cr(III) and Cr(VI) in the freshwater green alga Chlamydomonas reinhardtii

    Energy Technology Data Exchange (ETDEWEB)

    Aharchaou, Imad [Laboratoire Interdisciplinaire des Environnements Continentaux, UMR 7360, Université de Lorraine and CNRS, 8 rue du Général Delestraint, 57070 Metz (France); Rosabal, Maikel; Liu, Fengjie [Institut National de la Recherche Scientifique, Centre Eau Terre Environnement (INRS-ETE), 490 rue de la Couronne, Québec (Québec) G1K 9A9 (Canada); Battaglia, Eric; Vignati, Davide A.L. [Laboratoire Interdisciplinaire des Environnements Continentaux, UMR 7360, Université de Lorraine and CNRS, 8 rue du Général Delestraint, 57070 Metz (France); Fortin, Claude, E-mail: claude.fortin@ete.inrs.ca [Institut National de la Recherche Scientifique, Centre Eau Terre Environnement (INRS-ETE), 490 rue de la Couronne, Québec (Québec) G1K 9A9 (Canada)

    2017-01-15

    Highlights: • C. reinhardtii accumulated similar levels of Cr(III) and Cr(VI). • The subcellular partitioning of Cr(III) and Cr(VI) was similar. • Cr(III) and Cr(VI) associated mainly with organelles and heat-stable proteins. • Metallomic analysis showed two main Cr-binding biomolecules after 72 h of exposure. - Abstract: Chromium occurs in aquatic environments under two main redox forms, namely Cr(III) and Cr(VI), with different geochemical and biochemical properties. Cr(VI) readily crosses biological membranes of living organisms and once inside the cells it undergoes a rapid reduction to Cr(III). The route of entry for the latter form is, however, poorly known. Using the radioactive tracer {sup 51}Cr we compared the accumulation (absorption and adsorption) of the two Cr forms by the green unicellular alga Chlamydomonas reinhardii after 1 h and 72 h of exposure to 100 nM of either Cr(III) or Cr(VI) at pH 7. Both Cr forms had similar accumulation, with a major part in the extracellular (adsorbed) fraction after 1 h and a major part of total accumulated Cr in the intracellular (absorbed) fraction after 72 h. We also investigated the intracellular partitioning of Cr using an operational fractionation scheme and found that both Cr forms had similar distributions among fractions: Cr was mostly associated with organelles (23 ± 12% after 1 h and 37 ± 7% after 72 h) and cytosolic heat-stable proteins and peptides (39 ± 18% after 1 h and 35 ± 3% after 72 h) fractions. Further investigations using a metallomic approach (SEC-ICP-MS) were performed with the heat-stable proteins and peptides fraction to compare the distribution of the two Cr forms among various biomolecules of this fraction. One Cr-binding biomolecule (∼28 kDa) appeared after 1 h of exposure for both Cr species. After 72 h another biomolecule of lower molecular weight (∼0.7 kDa) was involved in binding Cr and higher signal intensities were observed for Cr(VI) than for Cr(III). We show, for the

  18. Bioaccumulation and subcellular partitioning of Cr(III) and Cr(VI) in the freshwater green alga Chlamydomonas reinhardtii

    International Nuclear Information System (INIS)

    Aharchaou, Imad; Rosabal, Maikel; Liu, Fengjie; Battaglia, Eric; Vignati, Davide A.L.; Fortin, Claude

    2017-01-01

    Highlights: • C. reinhardtii accumulated similar levels of Cr(III) and Cr(VI). • The subcellular partitioning of Cr(III) and Cr(VI) was similar. • Cr(III) and Cr(VI) associated mainly with organelles and heat-stable proteins. • Metallomic analysis showed two main Cr-binding biomolecules after 72 h of exposure. - Abstract: Chromium occurs in aquatic environments under two main redox forms, namely Cr(III) and Cr(VI), with different geochemical and biochemical properties. Cr(VI) readily crosses biological membranes of living organisms and once inside the cells it undergoes a rapid reduction to Cr(III). The route of entry for the latter form is, however, poorly known. Using the radioactive tracer "5"1Cr we compared the accumulation (absorption and adsorption) of the two Cr forms by the green unicellular alga Chlamydomonas reinhardii after 1 h and 72 h of exposure to 100 nM of either Cr(III) or Cr(VI) at pH 7. Both Cr forms had similar accumulation, with a major part in the extracellular (adsorbed) fraction after 1 h and a major part of total accumulated Cr in the intracellular (absorbed) fraction after 72 h. We also investigated the intracellular partitioning of Cr using an operational fractionation scheme and found that both Cr forms had similar distributions among fractions: Cr was mostly associated with organelles (23 ± 12% after 1 h and 37 ± 7% after 72 h) and cytosolic heat-stable proteins and peptides (39 ± 18% after 1 h and 35 ± 3% after 72 h) fractions. Further investigations using a metallomic approach (SEC-ICP-MS) were performed with the heat-stable proteins and peptides fraction to compare the distribution of the two Cr forms among various biomolecules of this fraction. One Cr-binding biomolecule (∼28 kDa) appeared after 1 h of exposure for both Cr species. After 72 h another biomolecule of lower molecular weight (∼0.7 kDa) was involved in binding Cr and higher signal intensities were observed for Cr(VI) than for Cr(III). We show, for the

  19. Comparative study of design of piping supports class 1, 2 and 3 considering german code KTA and ASME III - NF

    International Nuclear Information System (INIS)

    Faloppa, Altair A.; Fainer, Gerson; Mattar Neto, Miguel; Elias, Marcos V.

    2013-01-01

    The objective of this paper is developing a comparative study of the design criteria for class 1, 2, 3 piping supports considering the American Code ASME Section III - NF and the German Code KTA 3205.1 to the Primary Circuit, KTA 3205.2 to the others systems and KTA 3205.3 series-production standards supports of a PWR nuclear power plant. An additional purpose of the paper is a general analysis of the main design concepts of the American Code ASME Boiler and Pressure Vessel Code, Section III, Division 1 and German Nuclear Design Code KTA that was performed in order to aid the comparative study proposed. The relevance of this study is to show the differences between codes ASME and KTA since they were applied in the design of the Nuclear Power Plants Angra 1 and Angra 2, and to the design of Angra 3, which is at the moment under construction. It is also considered their use in the design of nuclear installations such as RMB - Reator MultiProposito Brasileiro and LABGENE - Laboratorio de Geracao Nucleoeletrica. (author)

  20. The Feasibility of Administering a Practical Clinical Examination in Podiatry at a College of Podiatric Medicine: Results of a Field Trial Under Simulated Part III Test Conditions.

    Science.gov (United States)

    And Others; Valletta, Michael

    1978-01-01

    The results of a practical clinical examination in podiatric medicine administered to fourth-year students are presented. The examination could become the prototype of a Part III practical clinical examination under the auspices of the National Board of Podiatry Examiners. Its feasibility is established and problems and issues are discussed.…

  1. Formation constants of Sm(III), Dy(III), Gd(III), Pr(III) and Nd(III) complexes of tridentate schiff base, 2-[(1H-benzimidazol-2-yl-methylene) amino] phenol

    International Nuclear Information System (INIS)

    Omprakash, K.L.; Chandra Pal, A.V.; Reddy, M.L.N.

    1982-01-01

    A new tridentate schiff base, 2- (1H-benzimidazol-2-yl-methylene)amino phenol derived from benzimididazole-2-carbo-xaldehyde and 2-aminophenol has been synthesised and characterised by spectral and analytical data. Proton-ligand formation constants of the schiff base and metal-ligand formation constants of its complexes with Sm(III), Dy(III), Gd(III), Nd(III) and Pr(III) have been determined potentiometrically in 50% (v/v) aqueous dioxane at an ionic strength of 0.1M (NaClO 4 ) and at 25deg C using the Irving-Rossotti titration technique. The order of stability constants (logβ 2 ) is found to be Sm(III)>Dy(III)>Gd(III)>Pr(III)>Nd(III). (author)

  2. Formation constants of Sm(III), Dy(III), Gd(III), Pr(III) and Nd(III) complexes of tridentate schiff base, 2-((1H-benzimidazol-2-yl-methylene) amino) phenol

    Energy Technology Data Exchange (ETDEWEB)

    Omprakash, K L; Chandra Pal, A V; Reddy, M L.N. [Osmania Univ., Hyderabad (India). Dept. of Chemistry

    1982-03-01

    A new tridentate schiff base, 2- (1H-benzimidazol-2-yl-methylene)amino phenol derived from benzimididazole-2-carbo-xaldehyde and 2-aminophenol has been synthesised and characterised by spectral and analytical data. Proton-ligand formation constants of the schiff base and metal-ligand formation constants of its complexes with Sm(III), Dy(III), Gd(III), Nd(III) and Pr(III) have been determined potentiometrically in 50% (v/v) aqueous dioxane at an ionic strength of 0.1M (NaClO/sub 4/) and at 25deg C using the Irving-Rossotti titration technique. The order of stability constants (log..beta../sub 2/) is found to be Sm(III)>Dy(III)>Gd(III)>Pr(III)>Nd(III).

  3. Drilling miniature holes, Part III

    Energy Technology Data Exchange (ETDEWEB)

    Gillespie, L.K.

    1978-07-01

    Miniature components for precision electromechanical mechanisms such as switches, timers, and actuators typically require a number of small holes. Because of the precision required, the workpiece materials, and the geometry of the parts, most of these holes must be produced by conventional drilling techniques. The use of such techniques is tedious and often requires considerable trial and error to prevent drill breakage, minimize hole mislocation and variations in hole diameter. This study of eight commercial drill designs revealed that printed circuit board drills produced better locational and size repeatability than did other drills when centerdrilling was not used. Boring holes 1 mm in dia, or less, as a general rule did not improve hole location in brass or stainless steel. Hole locations of patterns of 0.66-mm holes can be maintained within 25.4-..mu..m diametral positional tolerance if setup misalignments can be eliminated. Size tolerances of +- 3.8 ..mu..m can be maintained under some conditions when drilling flat plates. While these levels of precision are possible with existing off-the-shelf drills, they may not be practical in many cases.

  4. Technical Reports (Part I). End of Project Report, 1968-1971, Volume III.

    Science.gov (United States)

    Western Nevada Regional Education Center, Lovelock.

    The pamphlets included in this volume are technical reports prepared as outgrowths of the Student Information Systems of the Western Nevada Regional Education Center (WN-REC) funded by a Title III (Elementary and Secondary Education Act) grant. These reports describe methods of interpreting the printouts from the Student Information System;…

  5. A comparative study of external radiotherapy alone versus external radiotherapy + brachytherapy in carcinoma cervix stage III B

    International Nuclear Information System (INIS)

    Bardia, M.R.; Bhargava, S.C.; Chaudhary, R.K.; Agrawal, V.K.; Singh, K.; Vyas, R.

    1987-01-01

    Carcinoma of the cervix is the commonest cancer seen in women at Sardar Patel Medical College, Bikaner (Rajasthan). In the present study external radio-therapy and brachytherapy are used in carcinoma cervix stage III B. After 4000 to 4500 rads to pelvis by external radio-therapy, patient was assessed for intra cavitary application. Total given dose to point A was 7500 rads, to point B was 5000 rads. If patient was not suitable a split course was given where patient was asked to come after 3 weeks for intracavitary application. A comparative study of both methods was done. There was significant improvement in the control of central disease by applying intracavitary source. Radiation reactions were comparable. (author). 4 tables, 10 refs

  6. Spectrophotometric and pH-Metric Studies of Ce(III, Dy(III, Gd(III,Yb(III and Pr(III Metal Complexes with Rifampicin

    Directory of Open Access Journals (Sweden)

    A. N. Sonar

    2011-01-01

    Full Text Available The metal-ligand and proton-ligand stability constant of Ce(III, Dy(III, Gd(III,Yb(III and Pr(III metals with substituted heterocyclic drug (Rifampicin were determined at various ionic strength by pH metric titration. NaClO4 was used to maintain ionic strength of solution. The results obtained were extrapolated to the zero ionic strength using an equation with one individual parameter. The thermodynamic stability constant of the complexes were also calculated. The formation of complexes has been studied by Job’s method. The results obtained were of stability constants by pH metric method is confirmed by Job’s method.

  7. Complexes of lanthanum(III), cerium(III), samarium(III) and dysprosium(III) with substituted piperidines

    Energy Technology Data Exchange (ETDEWEB)

    Manhas, B S; Trikha, A K; Singh, H; Chander, M

    1983-11-01

    Complexes of the general formulae M/sub 2/Cl/sub 6/(L)/sub 3/.C/sub 2/H/sub 5/OH and M/sub 2/(NO/sub 3/)/sub 6/(L)/sub 2/.CH/sub 3/OH have been synthesised by the reactions of chlorides and nitrates of La(III), Ce(III), Sm(III) and Dy(III) with 2-methylpiperidine, 3-methylpiperidine and 4-methylpiperidine. These complexes have been characterised on the basis of their elemental analysis, and IR and electronic reflectance spectra. IR spectral data indicate the presence of coordinated ethanol and methanol molecules and bidentate nitrate groups. Coordination numbers of the metal ions vary from 5 to 8. 19 refs.

  8. Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

    International Nuclear Information System (INIS)

    Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E.

    2014-01-01

    Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH) 3 ·3H 2 O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH) 3 (am) was stable with a solubility lower than 50 μg/l in the range 5.7 0.75 Cr 0.25 (OH) 3 , the stability region was extended to 4.8 3 ·xH 2 O whereas in the presence of iron the precipitate is a mixed Fe (1−x) Cr x (OH) 3 phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe x ,Cr 1−x )(OH) 3 hydroxides as compared to the stability of Cr(OH) 3 . We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH) 3 ·3H 2 O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH) 3 (am) phase. Mixed Fe 0.75 Cr 0.25 (OH) 3 hydroxides were found to be of the ferrihydrite structure, Fe(OH) 3 , and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe(III)–Cr(III) hydroxides are more effective enhancers of groundwater quality, in comparison to the plain amorphous or crystalline Cr(III) hydroxides, the latter found to have a solubility typically higher than 50 μg/l (maximum EU permitted Cr level in drinking water), while the amorphous Cr(OH) 3 (am) phase was within the drinking water threshold in the range 5.7 0.75 Cr 0.25 (OH) 3 hydroxides studied were of extended stability in the 4.8 < pH < 13.5 range

  9. Comparing Part-time Employment in Germany, Sweden, Ireland and the Netherland

    DEFF Research Database (Denmark)

    Bekker, Sonja; Hipp, Lena; Leschke, Janine

    2017-01-01

    In the current discussions on combining work and family, the idea of shorter working hours is becoming ever more popular. However, much of the research on part-time employment has looked at women and mothers in particular. Much less is known about part-time work among men or fathers. Therefore......, this paper aims to establish the differences and similarities between men and women and particularly between mothers and fathers in their choices to work parttime, taking into account different household contexts and welfare state institutions. By analysing part-time work in Germany, Sweden, Ireland...... and the Netherlands in 2014 using individual level data from the European Labour Force Survey, we show that for men a lower earning capacity compared to their partner or family responsibilities do not seem to lead to higher part-time shares. This is the opposite of what we find for women. According to our analysis...

  10. CMPO-calix[4]arenes and the influence of structural modifications on the Eu(III), Am(III), Cm(III) separation

    International Nuclear Information System (INIS)

    Peters, C.; Braekers, D.; Desreux, J.F.; Kasyan, O.; Miroshnichenko, S.; Rudzevich, V.; Boehmer, V.

    2008-01-01

    The syntheses of new calix[4]arenes featuring CMPO groups on the wide rim are reported and the extraction of Am(III) and Eu(III) from concentrated HNO 3 aqueous phases are discussed with reference to the properties of the symmetric tetra-CMPO derivative 1. All extraction studies were conducted in the same experimental conditions which allows to directly compare the dependence of the distribution coefficients of various calixarenes on the acid concentration (0.1 M 3 ] < 5 M). Calix[4]arene 1 becomes a very poor extractant if the length of the aliphatic chain between the amide and phosphine oxide groups of CMPO is increased, if the bridging methylene groups are replaced by sulfur atoms or if the macrocyclic cavity size is increased. By contrast, mixed amide - CMPO calix[4]arenes are nearly as effective than 1. Moreover, Am(III)/Cm(III) separation coefficients between 1.5 and 3 have been obtained with unsymmetrical calix[4]arenes of type 1 with different aliphatic chains grafted on the narrow rim. Guidelines to anticipate the extraction ability of calix[4]arenes remain elusive because of the intricate solution behavior of these compounds. (orig.)

  11. Inner-sphere and outer-sphere complexes of yttrium(III), lanthanum (III), neodymium(III), terbium(III) and thulium(III) with halide ions in N,N-dimethylformamide

    International Nuclear Information System (INIS)

    Takahashi, Ryouta; Ishiguro, Shin-ichi

    1991-01-01

    The formation of chloro, bromo and iodo complexes of yttrium(III), and bromo and iodo complexes of lanthanum(III), neodymium(III), terbium(III) and thulium(III) has been studied by precise titration calorimetry in N,N-dimethylformamide (DMF) at 25 o C. The formation of [YCl] 2+ , [YCl 2 ] + , [YCl 3 ] and [YCl 4 ] - , and [MBr] 2+ and [MBr 2 ] + (M = Y, La, Nd, Tb, Tm) was revealed, and their formation constants, enthalpies and entropies were determined. It is found that the formation enthalpies change in the sequence ΔH o (Cl) > ΔH o (l), which is unusual for hard metal (III) ions. This implies that, unlike the chloride ion, the bromide ion forms outer-sphere complexes with the lanthanide(III) and yttrium(III) ions in DMF. Evidence for either an inner- or outer-sphere complex was obtained from 89 Y NMR spectra for Y(ClO 4 ) 3 , YCl 3 and YBr 3 DMF solutions at room temperature. (author)

  12. Fusion Power Demonstration III

    International Nuclear Information System (INIS)

    Lee, J.D.

    1985-07-01

    This is the third in the series of reports covering the Fusion Power Demonstration (FPD) design study. This volume considers the FPD-III configuration that incorporates an octopole end plug. As compared with the quadrupole end-plugged designs of FPD-I and FPD-II, this octopole configuration reduces the number of end cell magnets and shortens the minimum ignition length of the central cell. The end-cell plasma length is also reduced, which in turn reduces the size and cost of the end cell magnets and shielding. As a contiuation in the series of documents covering the FPD, this report does not stand alone as a design description of FPD-III. Design details of FPD-III subsystems that do not differ significantly from those of the FPD-II configuration are not duplicated in this report

  13. Physiotherapy and low back pain - part iii: outcomes research utilising the biosychosocial model: psychosocial outcomes

    Directory of Open Access Journals (Sweden)

    L. D. Bardin

    2003-02-01

    has evolved that necessitates the use of a biopsychosocial model, focusing on illness rather than disease and incorporating the biological, psychological and social aspects that are important to understand and to study LBP in its chronic form. Traditional outcome measures that measure elements within the biological component are limited to assess the spectrum of impacts caused by chronic low back pain (CLBP and the validity, reliability and sensitivity of some of these measures has been questioned.Few physiologic tests of spine function are clinically meaningful to patients, objective physical findings can be absent, and in CLBP disability and activity intolerance are often disproportional to the original injury. Biological outcomes should be complemented by outcomes of the psychosocial aspects of back pain that measure the considerable functional and emotional impact on the quality of life of patients experiencing low back dysfunction. Outcomes research is an analysis of clinical practice as it actually occurs and can  make a valuable contribution to understanding the multidimensional impact of LBP. Psychosocial aspects of the biopsychosocial model for outcomes research are discussed in part III: functional status/disability, psychological impairment, patient satisfaction, health related quality of life

  14. Toxic and hazardous chemicals, Title III and communities: An outreach manual for community groups

    International Nuclear Information System (INIS)

    McNeil, C.; Arkin, E.B.; McCallum, D.

    1989-09-01

    The manual was prepared for State and local government officials, local emergency planning committee (LEPCs), and other community groups that want to make Title III work. It is intended as a practical guide for those who have little or no previous experience in the field of communication, whose time must be snatched from home and office, and whose resources are limited. The manual has three major sections: Part I discusses planning, which is vital to the success of a communication program; Part II suggests ways to get and keep people involved, especially important because Title III affects so many different sectors of the community; Part III, a how-to-do-it section, talks about specific tasks, such as giving a speech or writing a press release. Appendices include a detailed explanation of the law, a glossary, a list of recent studies related to Title III communications, a list of educational materials, and a list of State contacts

  15. Elasto-dynamic analysis of a gear pump-Part III: Experimental validation procedure and model extension to helical gears

    Science.gov (United States)

    Mucchi, E.; Dalpiaz, G.

    2015-01-01

    This work concerns external gear pumps for automotive applications, which operate at high speed and low pressure. In previous works of the authors (Part I and II, [1,2]), a non-linear lumped-parameter kineto-elastodynamic model for the prediction of the dynamic behaviour of external gear pumps was presented. It takes into account the most important phenomena involved in the operation of this kind of machine. The two main sources of noise and vibration are considered: pressure pulsation and gear meshing. The model has been used in order to foresee the influence of working conditions and design modifications on vibration generation. The model's experimental validation is a difficult task. Thus, Part III proposes a novel methodology for the validation carried out by the comparison of simulations and experimental results concerning forces and moments: it deals with the external and inertial components acting on the gears, estimated by the model, and the reactions and inertial components on the pump casing and the test plate, obtained by measurements. The validation is carried out comparing the level of the time synchronous average in the time domain and the waterfall maps in the frequency domain, with particular attention to identify system resonances. The validation results are satisfactory globally, but discrepancies are still present. Moreover, the assessed model has been properly modified for the application to a new virtual pump prototype with helical gears in order to foresee gear accelerations and dynamic forces. Part IV is focused on improvements in the modelling and analysis of the phenomena bound to the pressure evolution around the gears in order to achieve results closer to the measured values. As a matter of fact, the simulation results have shown that a variable meshing stiffness has a notable contribution on the dynamic behaviour of the pump but this is not as important as the pressure phenomena. As a consequence, the original model was modified with the

  16. Evaluation of the hybrid III and Q-series pediatric ATD upper neck loads as compared to pediatric volunteers in low-speed frontal crashes.

    Science.gov (United States)

    Seacrist, Thomas; Mathews, Emily A; Balasubramanian, Sriram; Maltese, Matthew R; Arbogast, Kristy B

    2013-11-01

    Debate exists in the automotive community regarding the validity of the pediatric ATD neck response and corresponding neck loads. Previous research has shown that the pediatric ATDs exhibit hyper-flexion and chin-to-chest contact resulting in overestimations of neck loads and neck injury criteria. Our previous work comparing the kinematics of the Hybrid III and Q-series 6 and 10-year-old ATDs to pediatric volunteers in low-speed frontal sled tests revealed decreased ATD cervical and thoracic spine excursions. These kinematic differences may contribute to the overestimation of upper neck loads by the ATD. The current study compared upper neck loads of the Hybrid III and Q-series 6 and 10-year-old ATDs against size-matched male pediatric volunteers in low-speed frontal sled tests. A 3-D near-infrared target tracking system quantified the position of markers on the ATD and pediatric volunteers (head top, nasion, bilateral external auditory meatus). Shear force (F x ), axial force (F z ), bending moment (M y ), and head angular acceleration ([Formula: see text]) were calculated about the upper neck using standard equations of motion. In general, the ATDs underestimated axial force and overestimated bending moment compared to the human volunteers. The Hybrid III 6, Q6, and Q10 exhibited reduced head angular acceleration and modest increases in upper neck shear compared to the pediatric volunteers. The reduction in axial force and bending moment has important implications for neck injury predictions as both are used when calculating N ij . These analyses provide insight into the biofidelity of the pediatric ATD upper neck loads in low-speed crash environments.

  17. [Cephalometric analysis in cases with Class III malocclusions].

    Science.gov (United States)

    Rak, D

    1989-01-01

    Various orthodontic class III anomalies, classified into several experimental groups, and eugnathic occlusions serving as controls were studied by roentgencephalometry. The objective of the study was to detect possible distinctions in the quantitative values of two variables chosen and to select the variables which most significantly discriminate the group of class III orthodontic anomalies. Attempts were made to ascertain whether or not there were sex-related differences. The teleroentgenograms of 269 examines, aged 10-18 years, of both sexes were analyzed. The experimental group consisted of 89 examinees class III orthodontic anomalies. The control group consisted of 180 examines with eugnathic occlusion. Latero-lateral skull roentgenograms were taken observing the rules of roentgenocephalometry. Using acetate paper, the drawings of profile teleroentgenograms were elaborated and the reference points and lines were entered. A total of 38 variables were analyzed, of which there were 10 linear, 19 angular, and 8 variables were obtained by mathematical calculation; the age variable was also analyzed. In statistical analyses an electronic computer was used. The results are presented in tables and graphs. The results obtained showed that: --compared to the findings in the control group, the subjects in the experimental group displayed significant changes in the following craniofacial characteristics a negative difference in the position of the apical base of the jaw, manifest concavity of the osseous profile and diminished convexity of the profile of soft parts, retroinclination of the lower incisors, mandibular prognathism, increased mandibular angle and increased mandibular proportion compared to maxillary and the anterior cranial base; --with regard to the sex of the examinees, only four linear variables of significantly discriminating character were selected, so that in can be concluded that there were no significant sex differences among the morphological

  18. Comparative Evaluation of Conventional and Accelerated Castings on Marginal Fit and Surface Roughness

    Science.gov (United States)

    Jadhav, Vivek Dattatray; Motwani, Bhagwan K.; Shinde, Jitendra; Adhapure, Prasad

    2017-01-01

    Aims: The aim of this study was to evaluate the marginal fit and surface roughness of complete cast crowns made by a conventional and an accelerated casting technique. Settings and Design: This study was divided into three parts. In Part I, the marginal fit of full metal crowns made by both casting techniques in the vertical direction was checked, in Part II, the fit of sectional metal crowns in the horizontal direction made by both casting techniques was checked, and in Part III, the surface roughness of disc-shaped metal plate specimens made by both casting techniques was checked. Materials and Methods: A conventional technique was compared with an accelerated technique. In Part I of the study, the marginal fit of the full metal crowns as well as in Part II, the horizontal fit of sectional metal crowns made by both casting techniques was determined, and in Part III, the surface roughness of castings made with the same techniques was compared. Statistical Analysis Used: The results of the t-test and independent sample test do not indicate statistically significant differences in the marginal discrepancy detected between the two casting techniques. Results: For the marginal discrepancy and surface roughness, crowns fabricated with the accelerated technique were significantly different from those fabricated with the conventional technique. Conclusions: Accelerated casting technique showed quite satisfactory results, but the conventional technique was superior in terms of marginal fit and surface roughness. PMID:29042726

  19. Solvent extraction of anionic chelate complexes of lanthanum(III), europium(III), lutetium(III), scandium(III), and indium(III) with 2-thenoyltrifluoroacetone as ion-pairs with tetrabutylammonium ions

    International Nuclear Information System (INIS)

    Noro, Junji; Sekine, Tatsuya.

    1992-01-01

    The solvent extraction of lanthanum(III), europium(III), lutetium(III), scandium(III), and indium(III) in 0.1 mol dm -3 sodium nitrate solutions with 2-thenoyltrifluoroacetone (Htta) in the absence and presence of tetrabutylammonium ions (tba + ) into carbon tetrachloride was measured. The extraction of lanthanum(III), europium(III), and lutetium(III) was greatly enhanced by the addition of tba + ; this could be explained in terms of the extraction of a ternary complex, M(tta) 4 - tba + . However, the extractions of scandium(III) and indium(III) were nearly the same when tba + was added. The data were treated on the basis of the formation equilibrium of the ternary complex from the neutral chelate, M(tta) 3 , with the extracted ion-pairs of the reagents, tta - tba + , in the organic phase. It was concluded that the degree of association of M(tta) 3 with the ion-pair, tta - tba + , is greater in the order La(tta) 3 ≅ Eu(tta) 3 > Lu(tta) 3 , or that the stability of the ternary complex in the organic phase is higher in the order La(tta) 4 - tba + ≅ Eu(tta) 4 - tba + > Lu(tta) 4 - tba + . This is similar to those of adduct metal chelates of Htta with tributylphosphate (TBP) in synergistic extraction systems. (author)

  20. Theoretical analysis of nuclear reactors (Phase III), I-V, Part III, Reactor poisoning; Razrada metoda teorijske analize nuklearnih reaktora (III faza) I-IV, III Deo, Zatrovanje reaktora

    Energy Technology Data Exchange (ETDEWEB)

    Pop-Jordanov, J [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

    1963-01-15

    Report on calculation of poisoning in experimental and power reactor includes four parts. Part one describes the influence of poisoning on the physical parameters of a reactor. part two includes transformation of differential equations for iodine and xenon. It was needed for easier solution of of differential equation using the analog computer. This calculation was done for RA reactor operating at 5 MW power. The RA reactor was used an example of calculation by the proposed method. Part four shows the application of the method for calculating the Calder Hall power reactor.

  1. Radiation protection in category III large gamma irradiators

    International Nuclear Information System (INIS)

    Costa, Neivaldo; Furlan, Gilberto Ribeiro; Itepan, Natanael Marcio

    2011-01-01

    This article discusses the advantages of category III large gamma irradiator compared to the others, with emphasis on aspects of radiological protection, in the industrial sector. This category is a kind of irradiators almost unknown to the regulators authorities and the industrial community, despite its simple construction and greater radiation safety intrinsic to the model, able to maintain an efficiency of productivity comparable to those of category IV. Worldwide, there are installed more than 200 category IV irradiators and there is none of a category III irradiator in operation. In a category III gamma irradiator, the source remains fixed in the bottom of the tank, always shielded by water, negating the exposition risk. Taking into account the benefits in relation to radiation safety, the category III large irradiators are highly recommended for industrial, commercial purposes or scientific research. (author)

  2. Considerations Related to LTO for Gen II/III NPP

    International Nuclear Information System (INIS)

    Cojan, Mihail

    2012-01-01

    Today there are some 435 nuclear power reactors operating in 30 countries with a combined capacity of over 372 GWe. In 2011 these provided 2518 billion kWh, about 14% of the world's electricity [1]. The next evolutionary design of Generation III reactors to be deployed over many decades will represent a large part of the worldwide fleet throughout the 21st century. Generation III reactors are the future NPPs with improved safety and reliability, with passive safety systems and with a very low probability for core melt. The objective of this paper is to present the R and D activities that support LTO for Generation II / III Nuclear Reactors. (author)

  3. Construction of the Cleo III drift chamber

    International Nuclear Information System (INIS)

    Csorna, S.; Marka, S.; Dickson, M.; Dombrowski, S. von; Peterson, D.; Thies, P.; Glenn, S.; Thorndike, E.H.; Kravchenko, I.

    1998-01-01

    The CLEO III group is constructing a new chamber to be installed as part of the staged luminosity upgrade program at the Cornell electron storage ring and compatible with the interaction region optics. Although having less radial extent than the current CLEO II tracking system, CLEO III will have equivalent momentum resolution because of material reduction in the drift chamber inner skin and gas. The thin inner skin requires special attention to the end-plate motion due to wire creep. During stringing, use of a robot will fully automate the wire handling on the upper end. (author)

  4. The aminoterminal propeptide of type III procollagen. Studies on physiology and pathophysiology

    DEFF Research Database (Denmark)

    Jensen, L T

    1997-01-01

    receiving growth hormone therapy. We conclude: 1) That, for our purpose, the best method of determining PIIINP is the PIIINP RIA, owing to the profile of the substances determined. It was possible to improve the quality of the tracer and to increase sensitivity by changing the assay procedure. 2...... of peaks B and C (intact PIIINP) may, owing to the disposal rate, reflect changes in type III collagen turnover over one day (6 half-lives). The liver and kidneys actively take part in the degradation of circulating PIIINP. Serum concentrations of PIIINP in the presence of changing body composition (weight...... disappears when the body is in a catabolic state. Anabolic states give rise to increased serum concentrations of PIIINP as compared with normals states. The general conclusion is that serum PIIINP is a marker of type III collagen turnover under well-defined conditions. Serum PIIINP, mainly consisting...

  5. Uranium (III)-Plutonium (III) co-precipitation in molten chloride

    Science.gov (United States)

    Vigier, Jean-François; Laplace, Annabelle; Renard, Catherine; Miguirditchian, Manuel; Abraham, Francis

    2018-02-01

    Co-management of the actinides in an integrated closed fuel cycle by a pyrochemical process is studied at the laboratory scale in France in the CEA-ATALANTE facility. In this context the co-precipitation of U(III) and Pu(III) by wet argon sparging in LiCl-CaCl2 (30-70 mol%) molten salt at 705 °C is studied. Pu(III) is prepared in situ in the molten salt by carbochlorination of PuO2 and U(III) is then introduced as UCl3 after chlorine purge by argon to avoid any oxidation of uranium up to U(VI) by Cl2. The oxide conversion yield through wet argon sparging is quantitative. However, the preferential oxidation of U(III) in comparison to Pu(III) is responsible for a successive conversion of the two actinides, giving a mixture of UO2 and PuO2 oxides. Surprisingly, the conversion of sole Pu(III) in the same conditions leads to a mixture of PuO2 and PuOCl, characteristic of a partial oxidation of Pu(III) to Pu(IV). This is in contrast with coconversion of U(III)-Pu(III) mixtures but in agreement with the conversion of Ce(III).

  6. A Comparative Test of the Interval-Scale Properties of Magnitude Estimation and Case III Scaling and Recommendations for Equal-Interval Frequency Response Anchors.

    Science.gov (United States)

    Schriesheim, Chester A.; Novelli, Luke, Jr.

    1989-01-01

    Differences between recommended sets of equal-interval response anchors derived from scaling techniques using magnitude estimations and Thurstone Case III pair-comparison treatment of complete ranks were compared. Differences in results for 205 undergraduates reflected differences in the samples as well as in the tasks and computational…

  7. Inteligencia Artificial y Neurología. (III Parte

    Directory of Open Access Journals (Sweden)

    Mario Camacho Pinto

    1987-04-01

    Full Text Available

    De acuerdo con mi anuncio esta III Parte estaría constituida por los mecanismos cerebrales susceptibles de extrapolación tal como fueron enumerados por mí: control de input-output para realizar conductas, y de inteligencia y aprendizaje, de los cuales por razón de espacio sólo se publica la mitad en esta edición de Medicina. Se trata de una presentación esquemática, auncuando ahora encuentro quizás más atractivo el enfoque de J’urgen Ruech expuesto en el Capítulo Comunicación y Psiquiatría de la obra extensa de Freedman (1 así: Input = percepción; análisis de datos = reconocimiento; procesamiento de datos = pensamiento; almacenamiento de datos = memoria; output = expresión y acción. A mi modo de ver se completaría este encuadre funcional con el tópico aprendizaje, proceso contiguo al de la memoria. Antes de entrar en materia hago unas consideraciones preliminares. En la primera me refiero a otro enfoque del concepto de LA. no incluido anteriormente. Se trata de Schank Roger y Hunter Larry (2 para quienes las indagaciones a que conduce el trasegar acerca de lA son las más atrevidas de nuestra existencia: ¿cuál es la naturaleza de la mente, qué pasa cuando estamos pensando, sintiendo, viendo o entendiendo? ¿Es posible comprender cómo trabaja nuestra mente realmente? Preguntas milenarias en cuyas respuestas no se ha registrado progreso. La lA ofrece una nueva herramienta para avanzar en este sentido: el computador.

    Las teorías sobre la mente han consistido en procesos descriptivos. Y los planteamientos iníciales hechos sobre lA por los investigadores han sido enfocados hacia lo que ellos mismos consideraron como manifestaciones de alta inteligencia: problemas matemáticos, ajedrez, rompecabezas complejos, etc.; gran cantidad de energía fue dedicada y se encontraron técnicas computacionales exitosas. Pero se comprendió que las técnicas desarrolladas no eran las mismas que emplea el cerebro, por lo cual se

  8. Drivers of Costs Associated with Reperfusion Therapy in Acute Stroke: The IMS III Trial

    Science.gov (United States)

    Simpson, Kit N.; Simpson, Annie N.; Mauldin, Patrick D.; Hill, Michael D; Yeatts, Sharon D.; Spilker, Judith A.; Foster, Lydia D.; Khatri, Pooja; Martin, Renee; Jauch, Edward C.; Kleindorfer, Dawn; Palesch, Yuko Y.; Broderick, Joseph P.

    2014-01-01

    Background and Purpose The IMS III study tested the effect of IV t-PA alone as compared to IV t-PA followed by endovascular therapy and collected cost data to assess the economic implications of the two therapies. This report describes the factors affecting the costs of the initial hospitalization for acute stroke subjects from the US. Methods Prospective cost analysis of US subjects treated with IV t-PA alone or IV t-PA followed by endovascular therapy in the IMS III trial. Results compared to expected Medicare payments. Results The adjusted cost of a stroke admission in the study was $35,130 for subjects treated with endovascular therapy following IV t-PA treatment and $25,630 for subjects treated with IV t-PA alone (p<0.0001). Significant factors related to costs included treatment group, baseline NIH Stroke Scale, time from stroke onset to IV t-PA, age, stroke location, and comorbid diabetes. The mean cost for subjects who had routine use of general anesthesia as part of endovascular therapy was $46,444 as compared to $30,350 for those who did not have general anesthesia. The costs of embolectomy for IMS III subjects and patients from the NIS cohort exceeded the Medicare DRG payment in more than 75% of patients. Conclusion Minimizing the time to start of IV t-PA and decreasing the use of routine general anesthesia, may improve the cost-effectiveness of medical and endovascular therapy for acute stroke. PMID:24876261

  9. PIO I-II tendencies. Part 2. Improving the pilot modeling

    Directory of Open Access Journals (Sweden)

    Ioan URSU

    2011-03-01

    Full Text Available The study is conceived in two parts and aims to get some contributions to the problem ofPIO aircraft susceptibility analysis. Part I, previously published in this journal, highlighted the mainsteps of deriving a complex model of human pilot. The current Part II of the paper considers a properprocedure of the human pilot mathematical model synthesis in order to analyze PIO II typesusceptibility of a VTOL-type aircraft, related to the presence of position and rate-limited actuator.The mathematical tools are those of semi global stability theory developed in recent works.

  10. Má oclusão Classe III de Angle com discrepância ântero-posterior acentuada Angle Class III malocclusion with severe anteroposterior disharmony

    Directory of Open Access Journals (Sweden)

    Marcos Alan Vieira Bittencourt

    2009-02-01

    Full Text Available A má oclusão Classe III de Angle é caracterizada por uma discrepância dentária ântero-posterior, que pode ou não estar acompanhada por alterações esqueléticas. Em geral, o aspecto facial fica bastante comprometido, sendo justamente esse fator, na maioria das vezes, que motiva o paciente a procurar pelo tratamento. Este caso foi apresentado à Diretoria do Board Brasileiro de Ortodontia e Ortopedia Facial (BBO, representando a categoria 4, ou seja, uma má oclusão com discrepância ântero-posterior acentuada, Classe III, com ANB menor ou igual a -2º, como parte dos requisitos para a obtenção do título de Diplomado pelo BBO.Angle Class III malocclusion is characterized by an anteroposterior dental discrepancy which may or may not be accompanied by skeletal changes. In general, distressed by a significantly compromised facial aspect, patients tend to seek treatment. This case was presented to the Brazilian Board of Orthodontics and Facial Orthopedics (BBO, as representative of Category 4, i.e., a malocclusion with severe anteroposterior discrepancy, Class III, and ANB Angle equal to or smaller than -2º, as part of the requirements for obtaining the BBO Diploma.

  11. Distribution and Translocation of 141Ce (III) in Horseradish

    Science.gov (United States)

    Guo, Xiaoshan; Zhou, Qing; Lu, Tianhong; Fang, Min; Huang, Xiaohua

    2007-01-01

    Background and Aims Rare earth elements (REEs) are used in agriculture and a large amount of them contaminate the environment and enter foods. The distribution and translocation of 141Ce (III) in horseradish was investigated in order to help understand the biochemical behaviour and toxic mechanism of REEs in plants. Method The distribution and translocation of 141Ce (III) in horseradish were investigated using autoradiography, liquid scintillation counting (LSC) and electron microscopic autoradiography (EMARG) techniques. The contents of 141Ce (III) and nutrient elements were analysed using an inductively coupled plasma-atomic emission spectrometer (ICP-AES). Results The results from autoradiography and LSC indicated that 141Ce (III) could be absorbed by horseradish and transferred from the leaf to the leaf-stalk and then to the root. The content of 141Ce (III) in different parts of horseradish was as follows: root > leaf-stalk > leaf. The uptake rates of 141Ce (III) in horseradish changed with the different organs and time. The content of 141Ce (III) in developing leaves was greater than that in mature leaves. The results from EMARG indicated that 141Ce (III) could penetrate through the cell membrane and enter the mesophyll cells, being present in both extra- and intra-cellular deposits. The contents of macronutrients in horseradish were decreased by 141Ce (III) treatment. Conclusions 141Ce (III) can be absorbed and transferred between organs of horseradish with time, and the distribution was found to be different at different growth stages. 141Ce (III) can enter the mesophyll cells via apoplast and symplast channels or via plasmodesmata. 141Ce (III) can disturb the metabolism of macronutrients in horseradish. PMID:17921527

  12. Fe (III) complex of mefloquine hydrochloride: Synthesis ...

    African Journals Online (AJOL)

    As part of the ongoing research for more effective antimalarial drug, Fe (III) complex of mefloquine hydrochloride (antimalarial drug) was synthesized using template method. Mefloquine was tentatively found to have coordinated through the hydroxyl and the two nitrogen atoms in the quinoline and piperidine in the structure, ...

  13. Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

    Energy Technology Data Exchange (ETDEWEB)

    Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E., E-mail: gantipas@metal.ntua.gr

    2014-01-15

    Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH){sub 3}·3H{sub 2}O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH){sub 3}(am) was stable with a solubility lower than 50 μg/l in the range 5.7 < pH < 11. • For mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3}, the stability region was extended to 4.8 < pH < 13.5. -- Abstract: Chromium is a common contaminant of soils and aquifers and constitutes a major environmental problem. In nature, chromium usually exists in the form of two oxidation states, trivalent, Cr(III), which is relatively innocuous for biota and for the aquatic environment, and hexavalent, Cr(VI) which is toxic, carcinogenic and very soluble. Accordingly, the majority of wastewater and groundwater treatment technologies, include a stage where Cr(VI) is reduced to Cr(III), in order to remove chromium from the aqueous phase and bind the element in the form of environmentally stable solid compounds. In the absence of iron the final product is typically of the form Cr(OH){sub 3}·xH{sub 2}O whereas in the presence of iron the precipitate is a mixed Fe{sub (1−x)}Cr{sub x}(OH){sub 3} phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe{sub x},Cr{sub 1−x})(OH){sub 3} hydroxides as compared to the stability of Cr(OH){sub 3}. We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH){sub 3}·3H{sub 2}O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH){sub 3}(am) phase. Mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3} hydroxides were found to be of the ferrihydrite structure, Fe(OH){sub 3}, and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe(III)–Cr(III

  14. Diglycolic acid modified zirconium phosphate and studies on the extraction of Am(III) and Eu(III) from dilute nitric acid medium

    Energy Technology Data Exchange (ETDEWEB)

    Selvan, B. Robert; Suneesh, A.S.; Venkatesan, K.A.; Antony, M.P. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Fuel Chemistry Division; Dasthaiah, K.; Gardas, R.L. [Indian Institute of Technology - Madras, Chennai (India). Dept. of Chemistry

    2017-06-01

    Diglycolic acid modified zirconium phosphate (ZrP-DGA) was prepared and studied for the extraction of Am(III) and Eu(III) from dilute nitric acid medium. The distribution coefficient (K{sub d}, mL.g{sup -1}) of Am(III) and Eu(III) was measured as a function of time, pH and concentration of Eu(III) ion etc. The K{sub d} of Am(III) and Eu(III) increased with increase of pH, reached a maximum value of distribution coefficient at pH 1.5 - 2, followed by decrease in K{sub d} values. Rapid extraction of Am(III) and Eu(III) in ZrP-DGA was observed followed by the establishment of equilibrium occurred in 100 min. Kinetics of extraction was fitted in to pseudo second order rate equation. The amount of Eu(III) loaded in ZrP-DGA increased with increase in the concentration of Eu(III) ion in aqueous phase and the isotherm was fitted in to Langmuir and Freundlich adsorption models. The extraction of Am(III) in ZrP-DGA was higher as compared to Eu(III) and the interference of Eu(III) on the extraction of Am(III) was studied. The distribution coefficient of some lanthanides in ZrP-DGA was measured and the K{sub d} of lanthanides increased across the lanthanide series. The extracted trivalent metal ions were recovered in three contacts of loaded ZrP-DGA with 0.5 M nitric acid.

  15. Phase III randomized clinical trial comparing tremelimumab with standard-of-care chemotherapy in patients with advanced melanoma

    NARCIS (Netherlands)

    Ribas, Antoni; Kefford, Richard; Marshall, Margaret A.; Punt, Cornelis J. A.; Haanen, John B.; Marmol, Maribel; Garbe, Claus; Gogas, Helen; Schachter, Jacob; Linette, Gerald; Lorigan, Paul; Kendra, Kari L.; Maio, Michele; Trefzer, Uwe; Smylie, Michael; McArthur, Grant A.; Dreno, Brigitte; Nathan, Paul D.; Mackiewicz, Jacek; Kirkwood, John M.; Gomez-Navarro, Jesus; Huang, Bo; Pavlov, Dmitri; Hauschild, Axel

    2013-01-01

    In phase I/II trials, the cytotoxic T lymphocyte-associated antigen-4-blocking monoclonal antibody tremelimumab induced durable responses in a subset of patients with advanced melanoma. This phase III study evaluated overall survival (OS) and other safety and efficacy end points in patients with

  16. Phase III randomized clinical trial comparing tremelimumab with standard-of-care chemotherapy in patients with advanced melanoma.

    NARCIS (Netherlands)

    Ribas, A.; Kefford, R.; Marshall, Martin; Punt, C.J.A.; Haanen, J.B.; Marmol, M.; Garbe, C.; Gogas, H.; Schachter, J.; Linette, G.; Lorigan, P.; Kendra, K.L.; Maio, M.; Trefzer, U.; Smylie, M.; McArthur, G.A.; Dreno, B.; Nathan, P.D.; Mackiewicz, J.; Kirkwood, J.M.; Gomez-Navarro, J.; Huang, B.; Pavlov, D.; Hauschild, A.

    2013-01-01

    PURPOSE: In phase I/II trials, the cytotoxic T lymphocyte-associated antigen-4-blocking monoclonal antibody tremelimumab induced durable responses in a subset of patients with advanced melanoma. This phase III study evaluated overall survival (OS) and other safety and efficacy end points in patients

  17. Heating Changes Bio-Schwertmannite Microstructure and Arsenic(III Removal Efficiency

    Directory of Open Access Journals (Sweden)

    Xingxing Qiao

    2017-01-01

    Full Text Available Schwertmannite (Sch is an efficient adsorbent for arsenic(III removal from arsenic(III-contaminated groundwater. In this study, bio-schertmannite was synthesized in the presence of dissolved ferrous ions and Acidithiobacillus ferrooxidans LX5 in a culture media. Bio-synthesized Sch characteristics, such as total organic carbon (TOC, morphology, chemical functional groups, mineral phase, specific surface area, and pore volume were systematically studied after it was dried at 105 °C and then heated at 250–550 °C. Differences in arsenic(III removal efficiency between 105 °C dried-sch and 250–550 °C heated-sch also were investigated. The results showed that total organic carbon content in Sch and Sch weight gradually decreased when temperature increased from 105 °C to 350 °C. Sch partly transformed to another nanocrystalline or amorphous phase above 350 °C. The specific surface area of 250 °C heated-sch was 110.06 m2/g compared to 5.14 m2/g for the 105 °C dried-sch. Total pore volume of 105 °C dried-sch was 0.025 cm3/g with 32.0% mesopore and 68.0% macropore. However, total pore volume of 250 °C heated-mineral was 0.106 cm3/g with 23.6% micropore, 33.0% mesopore, and 43.4% macropore. The arsenic(III removal efficiency from an initial 1 mg/L arsenic(III solution (pH 7.5 was 25.1% when 0.25 g/L of 105 °C dried-sch was used as adsorbent. However, this efficiency increased to 93.0% when using 250 °C heated-sch as adsorbent. Finally, the highest efficiency for arsenic(III removal was obtained with sch-250 °C due to high amounts of sorption sites in agreement with the high specific surface area (SSA obtained for this sample.

  18. Binary and ternary chelates of scandium (III), Yttrium (III) and lanthanum (III) with ethyleneglycol-bis(. beta. -aminoethylether)-tetraacetic acid as primary and substituted salicylic acids as secondary ligands

    Energy Technology Data Exchange (ETDEWEB)

    Pandey, A K; Chandra, M; Agarwala, B V; Dey, A K [Allahabad Univ. (India). Chemical Labs.

    1980-01-01

    Formation constants of binary and ternary complexes of the systems of the type: M-L and M-egta-L (M = scandium(III), yttrium(III) and lanthanum(III), egta = ethylene glycol-bis(..beta..-aminoethylether)-tetra acetic acid, L = o-cresotic acid (o-ca), m-cresotic acid (m-ca), 5-chlorosalicyclic acid(csa), and 3,5-dibromosalicylic acid (dbsa)) have been determined pH-metrically at 25deg and ..mu.. = 0.1M (KNO/sub 3/) in 50% (v/v) aqueous-ethanol medium. The order of stabilities of ternary complexes has been compared with those of corresponding binary complexes, and results discussed on the basis of coulombic interactions.

  19. Automated Volumetric Modulated Arc Therapy Treatment Planning for Stage III Lung Cancer: How Does It Compare With Intensity-Modulated Radio Therapy?

    Energy Technology Data Exchange (ETDEWEB)

    Quan, Enzhuo M. [Department of Radiation Physics, University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Chang, Joe Y.; Liao Zhongxing [Department of Radiation Oncology, University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Xia Tingyi [Department of Radiation Oncology, Beijing 301 Hospital, Beijing (China); Yuan Zhiyong [Department of Radiation Oncology, Tianjin Medical University Cancer Hospital and Institute, Tianjin (China); Liu Hui [Department of Radiation Oncology, University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Department of Radiation Oncology, Zhongshan University Hospital, Guangzhou (China); Li, Xiaoqiang; Wages, Cody A.; Mohan, Radhe [Department of Radiation Physics, University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Zhang Xiaodong, E-mail: xizhang@mdanderson.org [Department of Radiation Physics, University of Texas MD Anderson Cancer Center, Houston, Texas (United States)

    2012-09-01

    Purpose: To compare the quality of volumetric modulated arc therapy (VMAT) or intensity-modulated radiation therapy (IMRT) plans generated by an automated inverse planning system with that of dosimetrist-generated IMRT treatment plans for patients with stage III lung cancer. Methods and Materials: Two groups of 8 patients with stage III lung cancer were randomly selected. For group 1, the dosimetrists spent their best effort in designing IMRT plans to compete with the automated inverse planning system (mdaccAutoPlan); for group 2, the dosimetrists were not in competition and spent their regular effort. Five experienced radiation oncologists independently blind-reviewed and ranked the three plans for each patient: a rank of 1 was the best and 3 was the worst. Dosimetric measures were also performed to quantitatively evaluate the three types of plans. Results: Blind rankings from different oncologists were generally consistent. For group 1, the auto-VMAT, auto-IMRT, and manual IMRT plans received average ranks of 1.6, 2.13, and 2.18, respectively. The auto-VMAT plans in group 1 had 10% higher planning tumor volume (PTV) conformality and 24% lower esophagus V70 (the volume receiving 70 Gy or more) than the manual IMRT plans; they also resulted in more than 20% higher complication-free tumor control probability (P+) than either type of IMRT plans. The auto- and manual IMRT plans in this group yielded generally comparable dosimetric measures. For group 2, the auto-VMAT, auto-IMRT, and manual IMRT plans received average ranks of 1.55, 1.75, and 2.75, respectively. Compared to the manual IMRT plans in this group, the auto-VMAT plans and auto-IMRT plans showed, respectively, 17% and 14% higher PTV dose conformality, 8% and 17% lower mean lung dose, 17% and 26% lower mean heart dose, and 36% and 23% higher P+. Conclusions: mdaccAutoPlan is capable of generating high-quality VMAT and IMRT treatment plans for stage III lung cancer. Manual IMRT plans could achieve quality

  20. Automated Volumetric Modulated Arc Therapy Treatment Planning for Stage III Lung Cancer: How Does It Compare With Intensity-Modulated Radio Therapy?

    International Nuclear Information System (INIS)

    Quan, Enzhuo M.; Chang, Joe Y.; Liao Zhongxing; Xia Tingyi; Yuan Zhiyong; Liu Hui; Li, Xiaoqiang; Wages, Cody A.; Mohan, Radhe; Zhang Xiaodong

    2012-01-01

    Purpose: To compare the quality of volumetric modulated arc therapy (VMAT) or intensity-modulated radiation therapy (IMRT) plans generated by an automated inverse planning system with that of dosimetrist-generated IMRT treatment plans for patients with stage III lung cancer. Methods and Materials: Two groups of 8 patients with stage III lung cancer were randomly selected. For group 1, the dosimetrists spent their best effort in designing IMRT plans to compete with the automated inverse planning system (mdaccAutoPlan); for group 2, the dosimetrists were not in competition and spent their regular effort. Five experienced radiation oncologists independently blind-reviewed and ranked the three plans for each patient: a rank of 1 was the best and 3 was the worst. Dosimetric measures were also performed to quantitatively evaluate the three types of plans. Results: Blind rankings from different oncologists were generally consistent. For group 1, the auto-VMAT, auto-IMRT, and manual IMRT plans received average ranks of 1.6, 2.13, and 2.18, respectively. The auto-VMAT plans in group 1 had 10% higher planning tumor volume (PTV) conformality and 24% lower esophagus V70 (the volume receiving 70 Gy or more) than the manual IMRT plans; they also resulted in more than 20% higher complication-free tumor control probability (P+) than either type of IMRT plans. The auto- and manual IMRT plans in this group yielded generally comparable dosimetric measures. For group 2, the auto-VMAT, auto-IMRT, and manual IMRT plans received average ranks of 1.55, 1.75, and 2.75, respectively. Compared to the manual IMRT plans in this group, the auto-VMAT plans and auto-IMRT plans showed, respectively, 17% and 14% higher PTV dose conformality, 8% and 17% lower mean lung dose, 17% and 26% lower mean heart dose, and 36% and 23% higher P+. Conclusions: mdaccAutoPlan is capable of generating high-quality VMAT and IMRT treatment plans for stage III lung cancer. Manual IMRT plans could achieve quality

  1. Aqueous phase complexation of Cm(III) and Cf(III) with ionizable macrocyclic ligands

    International Nuclear Information System (INIS)

    Manchanda, V.K.; Mohapatra, P.K.

    1995-01-01

    Complexation behaviour of Cm(III) and Cf(III) with 1,7-diaza-4,10,13-trioxacyclopentadecane-N,N'-diacetic acid (K21DA), 1,10-diaza-4,7,13,16-tetraoxacyclooctadecane-N,N'-diacetic acid (K22DA) and ethylene diamine N,N'- diacetic acid (EDDA) has been investigated using dinonyl naphthalene sulphonic acid (DNNS), in tetramethyl ammonium form as liquid cation exchanger. The aqueous phase complex formation constants are computed from the distribution data. Though larger complex formation constants are observed with K21DA as well as K22DA compared to those with the acyclic analog EDDA, no size correlation is observed. (author). 5 refs., 1 tab

  2. Analogues of Cucurbita maxima trypsin inhibitor III (CMTI-III) with elastase inhibitory activity.

    Science.gov (United States)

    Rózycki, J; Kupryszewski, G; Rolka, K; Ragnarsson, U; Zbyryt, T; Krokoszyńska, I; Wilusz, T

    1994-04-01

    Three new CMTI-III analogues containing the Val residue in the reactive site (position 5) were synthesized by the solid-phase method. The analogues displayed an elastase inhibitory activity. It is shown that the removal of the N-terminal Arg residue and the introduction of the Gly-Pro-Gln tripeptide in the region 23-25 decreases the antielastase activity by two orders of magnitude. The removal of the disulfide bridge in positions 16-28 and the substitution of Ala for Cys16 and Gly for Cys28 decreases the activity (measured as Ka with HLE) by five orders of magnitude as compared with [Val5]CMTI-III.

  3. Unraveling the Mystery of the Blue Fog: Structure, Properties, and Applications of Amorphous Blue Phase III.

    Science.gov (United States)

    Gandhi, Sahil Sandesh; Chien, Liang-Chy

    2017-12-01

    The amorphous blue phase III of cholesteric liquid crystals, also known as the "blue fog," are among the rising stars in materials science that can potentially be used to develop next-generation displays with the ability to compete toe-to-toe with disruptive technologies like organic light-emitting diodes. The structure and properties of the practically unobservable blue phase III have eluded scientists for more than a century since it was discovered. This progress report reviews the developments in this field from both fundamental and applied research perspectives. The first part of this progress report gives an overview of the 130-years-long scientific tour-de-force that very recently resulted in the revelation of the mysterious structure of blue phase III. The second part reviews progress made in the past decade in developing electrooptical, optical, and photonic devices based on blue phase III. The strong and weak aspects of the development of these devices are underlined and criticized, respectively. The third- and-final part proposes ideas for further improvement in blue phase III technology to make it feasible for commercialization and widespread use. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Spectroscopic and thermodynamic study of the complexation of Cm(III) and Eu(III) with hydrophilic bis-triazinyl pyridines

    International Nuclear Information System (INIS)

    Ruff, Christian

    2013-01-01

    In the present work the complexation of Cm(III) and Eu(III) with a hydrophilic 2,6-bis-(1,2,4-triazinyl)-pyridine (aq-BTP) is studied. Aq-BTP complexes actinides(III) selectively over lanthanides(III) in nitric acid solution. The object of this work is the identification and the spectroscopic and thermodynamic characterization of the Cm(III) and Eu(III) complex species present in solution. The results should contribute to a better fundamental understanding of the driving force behind BTPs selectivity towards trivalent actinides on a molecular level. Time-resolved laser fluorescence spectroscopy (TRLFS), luminescence and UV/Vis spectroscopy are applied. Information on the structure of M(III)-aq-BTP complex species is obtained from density functional theory. Three different M(III) complex species containing one, two or three aq-BTP ligands are identified in H 2 O at pH 3.0. Relative fluorescence intensity factors are determined for each of the [M(aq-BTP) n ] complexes (M = Cm(III)/Eu(III), n = 1 - 3). These factors are required to quantify the complexes. The stability constant logβ 3 of the [Cm(aq-BTP) 3 ] complex (which is the one relevant to extraction processes) is two orders of magnitude higher than that of the corresponding Eu(III) complex. This difference is in agreement with the separation factor (SF Am(III)/Eu(III) = 150) determined experimentally by liquid-liquid extraction. The difference in the stability constants originates from the different reaction enthalpies for the formation of the [M(aq-BTP) 3 ] complexes. These results represent the thermodynamic driving force for the aq-BTPs selectivity towards trivalent actinides over lanthanides. Comparing the stability constants of the [M(aq-BTP) n ] species (M = Cm(III)/Eu(III), n = 1 - 3) shows an increasing selectivity with increasing number of coordinated aq-BTP ligands. Hence, high selectivity is achieved if the f-element ions are fully coordinated by nine N-donor atoms (three aq-BTP ligands). A less

  5. Thermodecomposition of lanthanides (III) and ytrium (III) glucoheptonates

    International Nuclear Information System (INIS)

    Giolito, J.

    1987-01-01

    The lanthanides (III) and yttrium (III) glucoheptonates as well the D-glucoheptono 1-4 lactone were studied using common analytical methods, elemental microanalysis of carbon and hydrogen, thermogravimetry and differential scanning calorimetry. These compounds were prepared from the reaction between the lanthanides (III) and yttrium (III) hydroxides and glucoheptonic acid aqueous solution obtained by means of the delta lactone hydrolysis of this acid. After stoichiometric reaction the compounds were precipitated by the addition of absolute ethanol, washed with the same solvent and dried in desiccator. Thermogravimetric the (TG) curves of the lanthanides glucoheptonates of the ceric group present thermal profiles with enough differences permitting an easy caracterization of each compound and the yttrium (III) glucoheptonate TG curve showed a great similarity with the erbium (III) compound TG curve. The differential scanning calometry (DSC) curves showed endothermic and exothermic peaks by their shape, height and position (temperature) permit an easy and rapid identification of each compound specially if DSC and TG curves were examined simultaneously. (author) [pt

  6. Gender differences in Class III malocclusion.

    Science.gov (United States)

    Baccetti, Tiziano; Reyes, Brian C; McNamara, James A

    2005-07-01

    This study evaluated gender differences in the cephalometric records of a large-scale cross-sectional sample of Caucasian subjects with Class III malocclusion at different developmental ages. The purpose also was to provide average age-related and sex-related data for craniofacial measures in untreated Class III subjects that are used as reference in the diagnostic appraisal of the patient with Class III disharmony. The sample examined consisted of 1094 pretreatment lateral cephalometric records (557 female subjects and 537 male subjects) of Caucasian Class III individuals. The age range for female subjects was between three years six months and 57 years seven months. The male subject group ranged from three years three months to 48 years five months. Twelve age groups were identified. Skeletal maturity at different age periods also was determined using the stage of cervical vertebral maturation. Gender differences for all cephalometric variables were analyzed using parametric statistics. The findings of the study indicated that Class III malocclusion is associated with a significant degree of sexual dimorphism in craniofacial parameters, especially from the age of 13 onward. Male subjects with Class III malocclusion present with significantly larger linear dimensions of the maxilla, mandible, and anterior facial heights when compared with female subjects during the circumpubertal and postpubertal periods.

  7. Comparing the prevalence rates of social phobia in a community according to ICD-10 and DSM-III-R Comparando estimativas de prevalência da fobia social na comunidade empregando-se a CID-10 e a DSM-III-R

    Directory of Open Access Journals (Sweden)

    Fábio Lopes Rocha

    2005-09-01

    Full Text Available OBJECTIVE: This population-based study aimed to compare the prevalence rates of social phobia using DSM-III-R and CID-10, based on the Composite International Diagnostic Interview (CIDI, in a Brazilian community. METHODS: This survey was carried out in a representative sample of 1,041 residents from Bambuí, Minas Gerais, Brazil (attrition rate = 14.7%. The Brazilian version of the CIDI was used. One-month, one-year and lifetime social phobia prevalence rates were estimated, employing the DSM-III-R and ICD-10 classifications, using the CIDI computer program. RESULTS: One-month, one-year, and life prevalence rates of social phobia, based on the DSM-III-R (7.9, 9.0 and 11.7% respectively were higher than those based on the ICD-10 (4.7, 5.2 and 6.7% respectively; p OBJETIVO: Este estudo populacional visa comparar estimativas de prevalência de fobia social empregando-se a CID-10 e a DSM-III-R em uma comunidade brasileira. MÉTODOS: O levantamento foi realizado em uma amostra representativa de 1.041 residentes de Bambuí, Minas Gerais, Brasil (perda = 14,7%. Foi utilizada a versão brasileira da Composite International Diagnostic Interview (CIDI. As prevalências de 1 mês, 1 ano e vida foram estimadas empregando-se as classificações CID-10 e DSM-III-R, utilizando-se o programa de computador da CIDI. RESULTADOS: As prevalências de 1 mês, 1 ano e vida da fobia social, baseadas na DSM-III-R (7,9, 9,0 e 11,7% respectivamente foram mais elevadas que aquelas baseadas na CID-10 (4,7, 5,2 e 6,7%, respectivamente; p < 0,01 para todos. CONCLUSÃO: Nossos resultados reforçam a hipótese de que as taxas de prevalência de fobia social são mais elevadas quando baseadas na DSM-III-R em comparação com a CID-10.

  8. Extraction of Am (III) and Nd (III): comparison of TODGA and TEHDGA

    International Nuclear Information System (INIS)

    Gujar, R.B.; Murali, M.S.; Ansari, S.A.; Manchanda, V.K.

    2009-01-01

    Belonging to the class of extractants, diglycolamides which are recently explored and promising for actinide partitioning, two reagents (N, N, N', N'-tetraoctyl diglycolamide) TODGA and its isomerically substituted counterpart, (N, N, N', N'- tetraethylhexyl diglycolamide) TEHDGA after addition of suitable phase modifiers, Dihexyoctanamide and isodecanol respectively in dodecane have been compared in their extraction abilities for Am (III) and Nd (III) from nitric acid as well as simulated high-level waste solutions (SHLW) equivalent to HLW arising from PHWR fuel reprocessing. Both 0.1M TODGA + 0.5M DHOA and 0.2M TEHDGA + 30% isodecanol in dodecane display high distribution ratios for the trivalent metal ions of f-elements. Similarities and differences in their extraction are discussed. (author)

  9. The regulatory framework of trade finance: from BASEL I to BASEL III

    Directory of Open Access Journals (Sweden)

    Claudia BAICU

    2011-09-01

    Full Text Available The global crisis revealed several weaknesses in the international framework of banking regulation. Consequently, the Basel Committee on Banking Supervision (BCBS proposed a package of measures to strengthen the resilience of the banking sector. Besides the positive effects they have on financial stability, the new regulatory provisions affect the ability of banks to provide trade finance. Therefore, the banking industry considers that regulators have not taken into account the low-risk profile of activity. Starting from this premise, the paper consists of three parts. In the first part, the role and objectives of the BCBS are presented; the second part is designed to review the most important trade instruments and to underline the tendencies in trade finance; finally, the last part highlights the regulation of trade finance under the Basel I, Basel II and Basel III regimes, and some unintended consequences of the Basel III framework.

  10. Archform comparisons between skeletal class II and III malocclusions.

    Directory of Open Access Journals (Sweden)

    Wei Zou

    Full Text Available The purpose of this cross-sectional research was to explore the relationship of the mandibular dental and basal bone archforms between severe Skeletal Class II (SC2 and Skeletal Class III (SC3 malocclusions. We also compared intercanine and intermolar widths in these two malocclusion types. Thirty-three virtual pretreatment mandibular models (Skeletal Class III group and Thirty-five Skeletal Class II group pretreatment models were created with a laser scanning system. FA (the midpoint of the facial axis of the clinical crownand WALA points (the most prominent point on the soft-tissue ridgewere employed to produce dental and basal bone archforms, respectively. Gained scatter diagrams of the samples were processed by nonlinear regression analysis via SPSS 17.0. The mandibular dental and basal bone intercanine and intermolar widths were significantly greater in the Skeletal Class III group compared to the Skeletal Class II group. In both groups, a moderate correlation existed between dental and basal bone arch widths in the canine region, and a high correlation existed between dental and basal bone arch widths in the molar region. The coefficient of correlation of the Skeletal Class III group was greater than the Skeletal Class II group. Fourth degree, even order power functions were used as best-fit functions to fit the scatter plots. The radius of curvature was larger in Skeletal Class III malocclusions compared to Skeletal Class II malocclusions (rWALA3>rWALA2>rFA3>rFA2. In conclusion, mandibular dental and basal intercanine and intermolar widths were significantly different between the two groups. Compared with Skeletal Class II subjects, the mandibular archform was more flat for Skeletal Class III subjects.

  11. Sorption of trace amounts of gallium (III) on iron (III) oxide

    International Nuclear Information System (INIS)

    Music, S.; Gessner, M.; Wolf, R.H.H.

    1979-01-01

    The sorption of trace amounts of gallium(III) on iron(III) oxide has been studied as a function of pH. Optimum conditions have been found for the preconcentration of traces of gallium(III) by iron(III) oxide. The influence of surface active substances and of complexing agents on the sorption of trace amounts of gallium(III) on iron(III) oxide has been also studied. (orig.) [de

  12. Sorption of trace amounts of gallium (III) on iron (III) oxide

    Energy Technology Data Exchange (ETDEWEB)

    Music, S; Gessner, M; Wolf, R H.H. [Institut Rudjer Boskovic, Zagreb (Yugoslavia)

    1979-01-01

    The sorption of trace amounts of gallium(III) on iron(III) oxide has been studied as a function of pH. Optimum conditions have been found for the preconcentration of traces of gallium(III) by iron(III) oxide. The influence of surface active substances and of complexing agents on the sorption of trace amounts of gallium(III) on iron(III) oxide has been also studied.

  13. WISC-III e WAIS-III na avaliação da inteligência de cegos WISC-III/WAIS-III en ciegos WISC-III and WAIS-III in intellectual assessment of blind people

    Directory of Open Access Journals (Sweden)

    Elizabeth do Nascimento

    2007-12-01

    Full Text Available Diante da escassez de pesquisas nacionais e de testes psicológicos destinados a avaliar pessoas cegas, desenvolveu-se um estudo psicométrico com as escalas verbais dos testes WISC-III e WAIS-III. Após as adaptações de alguns estímulos e das instruções, os testes foram aplicados em crianças (N = 120 e adultos (N = 52 residentes em Belo Horizonte. Os resultados indicaram que as escalas verbais modificadas apresentam uma boa consistência interna (alfa> 0,80. Além disso, a investigação da validade fatorial identifica a presença clara de apenas um componente. Este componente explica 81% e 64% para o WISC-III e WAIS-III, respectivamente. Conclui-se que as adaptações a que se procedeu não afetaram a estrutura fatorial das escalas. Deste modo, os profissionais poderão utilizar as escalas modificadas para avaliar a inteligência de pessoas cegas.Frente a la escasez de investigaciones nacionales asi como la ausencia de tests psicológicos que evaluen personas ciegas, se ha desarrollado un estudio psicometrico com la escalas verbales del WISC-III y WAIS-III. Posteriormente a las adaptaciones de algunos estímulos y de las instrucciones, las escalas fueron aplicadas a una muestra de niños (n=120 y de adultos (n=52 residentes en la ciudad de Belo Horizonte-Brasil. Los resultados indican que las escalas verbales modificadas presentan una alta fiabilidad (alpha >0,80 asi como la presencia clara de un unico componente responsable por 81% y 64% de la variancia del WIC-III e WAIS-III respectivamente. Se ha concluido que las modificaciones efectuadas no han comprometido la estructura factorial de las escalas verbales. Por tanto, los profesionales psicólogos pueden utilizar las escalas modificadas para la evaluación de la inteligencia de personas portadoras de ceguera.Owing to the almost lack of a national research on psychological testing for the evaluation of blind people, a psychometric study has been developed with the WISC-III and WAIS-III

  14. Comparing fish communities in sanctuaries, partly protected areas ...

    African Journals Online (AJOL)

    Within coral-dominated reefs, abundances of indicator taxa showed three patterns: (1) greatest abundance in sanctuaries, intermediate in partly protected and least in open areas; (2) greatest abundance in sanctuaries but equal diminishment in partly protected and open areas; and (3) greater depletion in partly protected ...

  15. Environmentally-relevant concentrations of Al(III) and Fe(III) cations induce aggregation of free DNA by complexation with phosphate group.

    Science.gov (United States)

    Qin, Chao; Kang, Fuxing; Zhang, Wei; Shou, Weijun; Hu, Xiaojie; Gao, Yanzheng

    2017-10-15

    Environmental persistence of free DNA is influenced by its complexation with other chemical species and its aggregation mechanisms. However, it is not well-known how naturally-abundant metal ions, e.g., Al(III) and Fe(III), influence DNA aggregation. This study investigated aggregation behaviors of model DNA from salmon testes as influenced by metal cations, and elucidated the predominant mechanism responsible for DNA aggregation. Compared to monovalent (K + and Na + ) and divalent (Ca 2+ and Mg 2+ ) cations, Al(III) and Fe(III) species in aqueous solution caused rapid DNA aggregations. The maximal DNA aggregation occurred at 0.05 mmol/L Al(III) or 0.075 mmol/L Fe(III), respectively. A combination of atomic force microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy revealed that Al(III) and Fe(III) complexed with negatively charged phosphate groups to neutralize DNA charges, resulting in decreased electrostatic repulsion and subsequent DNA aggregation. Zeta potential measurements and molecular computation further support this mechanism. Furthermore, DNA aggregation was enhanced at higher temperature and near neutral pH. Therefore, DNA aggregation is collectively determined by many environmental factors such as ion species, temperature, and solution pH. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Indication of the Hanle Effect by Comparing the Scattering Polarization Observed by CLASP in the Ly α and Si iii 120.65 nm Lines

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, R.; Kubo, M.; Kano, R.; Narukage, N.; Bando, T.; Katsukawa, Y.; Giono, G.; Suematsu, Y.; Hara, H. [National Astronomical Observatory of Japan, National Institutes of Natural Science, 2-21-1 Osawa, Mitaka, Tokyo 181-8588 (Japan); Bueno, J. Trujillo [Instituto de Astrofísica de Canarias, E-38205 La Laguna, Tenerife (Spain); Uitenbroek, H. [National Solar Observatory, 3665 Discovery Drive, Boulder, CO 80303 (United States); Tsuneta, S.; Ishikawa, S.; Shimizu, T.; Sakao, T. [Institute of Space and Astronautical Science, Japan Aerospace Exploration Agency, 3-1-1 Yoshinodai, Chuo, Sagamihara, Kanagawa 252-5210 (Japan); Goto, M. [National Institute for Fusion Science, National Institutes of Natural Sciences, Toki, Gifu 509-5292 (Japan); Winebarger, A.; Kobayashi, K. [NASA Marshall Space Flight Center, ZP 13, Huntsville, AL 35812 (United States); Cirtain, J. [University of Virginia, Department of Astronomy, 530 McCormick Road, Charlottesville, VA 22904 (United States); Champey, P. [University of Alabama in Huntsville, 301 Sparkman Drive, Huntsville, AL 35899 (United States); and others

    2017-05-20

    The Chromospheric Lyman-Alpha Spectro-Polarimeter is a sounding rocket experiment that has provided the first successful measurement of the linear polarization produced by scattering processes in the hydrogen Ly α line (121.57 nm) radiation of the solar disk. In this paper, we report that the Si iii line at 120.65 nm also shows scattering polarization and we compare the scattering polarization signals observed in the Ly α and Si iii lines in order to search for observational signatures of the Hanle effect. We focus on four selected bright structures and investigate how the U / I spatial variations vary between the Ly α wing, the Ly α core, and the Si iii line as a function of the total unsigned photospheric magnetic flux estimated from Solar Dynamics Observatory /Helioseismic and Magnetic Imager observations. In an internetwork region, the Ly α core shows an antisymmetric spatial variation across the selected bright structure, but it does not show it in other more magnetized regions. In the Si iii line, the spatial variation of U / I deviates from the above-mentioned antisymmetric shape as the total unsigned photospheric magnetic flux increases. A plausible explanation of this difference is the operation of the Hanle effect. We argue that diagnostic techniques based on the scattering polarization observed simultaneously in two spectral lines with very different sensitivities to the Hanle effect, like Ly α and Si iii, are of great potential interest for exploring the magnetism of the upper solar chromosphere and transition region.

  17. COMPARATIVE STUDY OF DEGRADATION OF ISOPROTURON (3-(4-isopropylphenyl-1,1dimethylurea PHOTOINDUCED BY FE(III AND FE(III-PHOTOINDUCED SONOCHEMICAL IN AQUEOUS SOLUTION

    Directory of Open Access Journals (Sweden)

    S Azizi

    2014-05-01

    Full Text Available The degradation of isoproturon 3-(4-isopropylphenyl-1,1dimethylurea photoinduced by Fe(III in aqueous solution has been investigated. The rate of degradation depends on the concentration of Fe(OH2+, the most photoreactive species in terms of .OH radical formation. These .OH radicals are able to degrade isoproturon until total mineralisation. The formation  of  Fe(II in the irradiated solution was monitored. The sonophotochemical degradation of isoproturon has been found to be dependent on the intensity of sonication. The combination of ultrasound and photochemistry has been used to degrade an aqueous solution of Isoproturon (IP. The degradation of IP in aqueous solution was investigated under sonolysis at         500 kHz and in the presence of Fe(III, as well as under simultaneous sonolysis and photoinduced Fe(III. Coupling photolysis with ultrasound for degradation of IP has been developed. The photosonochemical decomposition rate constant is greater than the additive rate constants of the two processes. Degradation products were analysed by CG/MS performed in the electron-impact (EI mode, at 70 eV potential using full scan mode. Degradation photoproducts were identified and a mechanism of degradation is proposed for two processes.

  18. Dramatic improvement in photostability of luminescent Eu(III) complexes with tetraphenylimidodiphosphinate ligand

    International Nuclear Information System (INIS)

    Zheng, Wei; Li, Shu-Jing; Li, Cheng-Hui; Zheng, You-Xuan; You, Xiao-Zeng

    2014-01-01

    In this paper, we synthesized and characterized a new Eu(III) tetraphenylimidodiphosphinate complex with dimethyl sulfoxide (DMSO) as co-ligand. Moreover, we compared the photostability of a series of Eu(III) complexes containing tetraphenylimidodiphosphinate ligands, Eu(tpip) 3 , Eu(tpip) 3 Phen, Eu(tpip) 3 DMSO, with their analogs of 1,3-dibenzoylmethanate, Eu(dbm) 3 ∙2H 2 O, Eu(dbm) 3 Phen, Eu(dbm) 3 (DMSO) 2 . We found that the photostability of the luminescent Eu(III) complexes was significantly improved upon substitution of the 1,3-diketones with tetraphenylimidodiphosphinate ligands. -- Highlights: • We synthesized and characterized a new Eu(III) tetraphenylimidodiphosphinate complexes with dimethyl sulfoxide. • We compared the photostability of Eu(III) complex with tetraphenylimidodiphosphinate and 1,3-dibenzoylmethanate ligands. • The photostability is significantly improved in Eu(III) complexes with tetraphenylimidodiphosphinate ligands

  19. Human Retroviruses and AIDS. A compilation and analysis of nucleic acid and amino acid sequences: I--II; III--V

    Energy Technology Data Exchange (ETDEWEB)

    Myers, G.; Korber, B. [eds.] [Los Alamos National Lab., NM (United States); Wain-Hobson, S. [ed.] [Laboratory of Molecular Retrovirology, Pasteur Inst.; Smith, R.F. [ed.] [Baylor Coll. of Medicine, Houston, TX (United States). Dept. of Pharmacology; Pavlakis, G.N. [ed.] [National Cancer Inst., Frederick, MD (United States). Cancer Research Facility

    1993-12-31

    This compendium and the accompanying floppy diskettes are the result of an effort to compile and rapidly publish all relevant molecular data concerning the human immunodeficiency viruses (HIV) and related retroviruses. The scope of the compendium and database is best summarized by the five parts that it comprises: (I) HIV and SIV Nucleotide Sequences; (II) Amino Acid Sequences; (III) Analyses; (IV) Related Sequences; and (V) Database Communications. Information within all the parts is updated at least twice in each year, which accounts for the modes of binding and pagination in the compendium.

  20. Uranium (III) precipitation in molten chloride by wet argon sparging

    Energy Technology Data Exchange (ETDEWEB)

    Vigier, Jean-François, E-mail: jean-francois.vigier@ec.europa.eu [CEA, Nuclear Energy Division, Radiochemistry & Processes Department, F-30207 Bagnols sur Cèze (France); Unité de Catalyse et de Chimie du Solide, UCCS UMR CNRS 8181, Univ. Lille Nord de France, ENSCL-USTL, B.P. 90108, 59652 Villeneuve d' Ascq Cedex (France); Laplace, Annabelle [CEA, Nuclear Energy Division, Radiochemistry & Processes Department, F-30207 Bagnols sur Cèze (France); Renard, Catherine [Unité de Catalyse et de Chimie du Solide, UCCS UMR CNRS 8181, Univ. Lille Nord de France, ENSCL-USTL, B.P. 90108, 59652 Villeneuve d' Ascq Cedex (France); Miguirditchian, Manuel [CEA, Nuclear Energy Division, Radiochemistry & Processes Department, F-30207 Bagnols sur Cèze (France); Abraham, Francis [Unité de Catalyse et de Chimie du Solide, UCCS UMR CNRS 8181, Univ. Lille Nord de France, ENSCL-USTL, B.P. 90108, 59652 Villeneuve d' Ascq Cedex (France)

    2016-06-15

    In the context of pyrochemical processes for nuclear fuel treatment, the precipitation of uranium (III) in molten salt LiCl-CaCl{sub 2} (30–70 mol%) at 705 °C is studied. First, this molten chloride is characterized with the determination of the water dissociation constant. With a value of 10{sup −4.0}, the salt has oxoacid properties. Then, the uranium (III) precipitation using wet argon sparging is studied. The salt is prepared using UCl{sub 3} precursor. At the end of the precipitation, the salt is totally free of solubilized uranium. The main part is converted into UO{sub 2} powder but some uranium is lost during the process due to the volatility of uranium chloride. The main impurity of the resulting powder is calcium. The consequences of oxidative and reductive conditions on precipitation are studied. Finally, coprecipitation of uranium (III) and neodymium (III) is studied, showing a higher sensitivity of uranium (III) than neodymium (III) to precipitation. - Highlights: • Precipitation of Uranium (III) is quantitative in molten salt LiCl-CaCl{sub 2} (30–70 mol%). • The salt is oxoacid with a water dissociation constant of 10{sup −4.0} at 705 °C. • Volatility of uranium chloride is strongly reduced in reductive conditions. • Coprecipitation of U(III) and Nd(III) leads to a consecutive precipitation of the two elements.

  1. Complexation of Cucurbit(7)uril with Eu(III)

    International Nuclear Information System (INIS)

    Kar, Aishwarya; Rawat, Neetika; Rao, Ankita; Tomar, B.S.; Nayak, S.K.; Ray, Alok

    2014-01-01

    Cucurbiturils (CBs) CB(n)s are macrocyclic molecules with carbonyl groups at the portals, which bind cations through ion dipole interactions and the cavity which stabilize hydrophobic moieties. The size of the portal and the volume of the interior cavities of CB(n)s are dependent on the number of glycoluril units present in CBs. CBs are widely used as supramolecular host systems in applications, such as formation of supramolecular hydrogels, drug delivery systems. Though the binding of CBs with organic guest molecules have been studied extensively where as metal complexation studies are very few. In the present work, complexation studies of Cucurbit(7)uril (with seven glycouril units, CB7) with Eu(III) were carried out using fluorescence, UV-vis spectrophotometry. The stability constant for 1:1 complex CB7-Eu(III) complex determined by monitoring the change in CB7 UV- vis absorption spectra on addition of Eu(III) was found to be 2.99 ± 0.08. The fluorescence spectra of increasing ligand to metal ratio exhibited the increase in the intensity ratio of peak at 616 and 592 which is the measure of complexation of Eu(III) with CB7 and was used to deduce the stability constant and the value (2.82 ± 0.07) obtained was in good agreement with that obtained from UV vis spectroscopy. Further, the life time of Eu(III) ion, which increased with CB7 to Eu(III) ratio, was used to deduce number of water molecules around Eu(III) metal ion which were found to decrease from 9 to 3 thereby suggesting inner sphere complexation. The stability constant of CB7 with Eu(III) is one order of magnitude less than CB5, derived in separate study by authors. The smaller cavity of CB5 (2.4 A 0 ) favors its interactions with Eu(III) ion of comparable diameter (2.16 A 0 ) leading to higher stability constant compared to CB7 (5.4 A 0 ) having larger cavity

  2. 50 CFR 23.4 - What are Appendices I, II, and III?

    Science.gov (United States)

    2010-10-01

    ... (CONTINUED) TAKING, POSSESSION, TRANSPORTATION, SALE, PURCHASE, BARTER, EXPORTATION, AND IMPORTATION OF... of Appendix-I, -II, and -III species and their parts, products, and derivatives through a system of...

  3. Extraction and separation studies of Ga(III, In(III and Tl(III using the neutral organophosphorous extractant, Cyanex-923

    Directory of Open Access Journals (Sweden)

    P. M. DHADKE

    2003-07-01

    Full Text Available The neutral extractant, Cyanes-923 has been used for the extraction and separation of gallium(III, indium(III and thallium(III from acidic solution. These metal ions were found to be quantitatively extracted with Cyanex-923 in toluene in the pH range 4.5–5.5, 5.0–6.5 and 1.5–3.0, respectively, and from the organic phase they can be stripped with 2.0 mol dm-3 HNO3, 3.0 mol dm-3 HNO3 and 3.0 mol dm-3 HCl, respectively. The effect of pH equilibration period, diluents, diverse ions and stripping agents on the extraction of Ga(III, In(III and Tl(III has been studied. The stroichiometry of the extracted species of these metal ions was determined on the basis of the slope analysis method. The reaction proceed by solvation and the probable extracted species found were [MCl3. 3Cyanex-923] [where M = Ga(III or In(III ] and [HTlCl4. 3Cyanex-923]. Based on these results a sequential procedure for the separation of Ga(III, In(III and Tl(III from each other was developed.

  4. 40 CFR Table 1 to Subpart III of... - HAP ABA Formulation Limitations Matrix for New Sources [see § 63.1297(d)(2)

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 11 2010-07-01 2010-07-01 true HAP ABA Formulation Limitations Matrix for New Sources [see § 63.1297(d)(2)] 1 Table 1 to Subpart III of Part 63 Protection of Environment... Flexible Polyurethane Foam Production Pt. 63, Subpt. III, Table 1 Table 1 to Subpart III of Part 63—HAP ABA...

  5. A Stable, Non-Cesiated III-Nitride Photocathode for Ultraviolet Astronomy Application

    Science.gov (United States)

    Bell, Lloyd

    In this effort, we propose to develop a new type of cesium-free photocathode using III-nitride (III-N) materials (GaN, AlN, and their alloys) and to achieve highly efficient, solar blind, and stable UV response. Currently, detectors used in UV instruments utilize a photocathode to convert UV photons into electrons that are subsequently detected by microchannel plate or CCD. The performance of these detectors critically depends on the efficiency and stability of their photocathodes. In particular, photocathode instability is responsible for many of the fabrication difficulties commonly experienced with this class of detectors. In recent years, III-N (in particular GaN) photocathodes have been demonstrated with very high QE (>50%) in parts of UV spectral range. Moreover, due to the wide bandgaps of III-nitride materials, photocathode response can be tailored to be intrinsically solar-blind. However, these photocathodes still rely on cesiation for activation, necessitating all-vacuum fabrication and sealed-tube operation. The proposed photocathode structure will achieve activation through methods for band structure engineering such as delta-doping and polarization field engineering. Compared to the current state-of-the-art in flight-ready microchannel plate sealed tubes, photocathodes based on III-N materials will yield high QE and significantly enhance both fabrication yield and reliability, since they do not require cesium or other highly reactive materials for activation. This performance will enable a ~4 meter medium class UV spectroscopic and imaging mission that is of high scientific priority for NASA. This work will build on the success of our previous APRA-funded effort. In that work, we demonstrated III-nitride photocathode operation without the use of cesium and stable response with respect to time. These accomplishments represent major improvements to the state-of-the-art for photocathode technologies. In the proposed effort, we will implement III

  6. Potentiometric studies on some ternary complexes of Nd(III), Sm(III), Gd(III) and Ho(III) with cyclohexanediaminetetraacetic acid as primary ligand

    International Nuclear Information System (INIS)

    Marathe, D.G.; Munshi, K.N.

    1983-01-01

    The formation constants of the ternary complexes of neodymium(III), samarium(III), gadlonium(III) and holmium(III) with cyclohexanediaminetetraacetic acid (CyDTA) as primary ligand and dihydroxynaphthalene (DHN), dihydroxynaphthalene-6-sulphonic acid (DHNSA) and cateechol-3,5-disulphonic acid (CDSA) as secondary ligands have been investigated by potentiometric titration technique. The secondary ligands have been investigated by potentiometric titration technique. The values of formation constants of 1:1:1 ternary chelates are reported at three different temperatures, and at a fixed ionic strength, μ = 0.1 M (NaClO 4 ). (author)

  7. Orthodontic camouflage versus orthognathic surgery for class III deformity: comparative cephalometric analysis.

    Science.gov (United States)

    Martinez, P; Bellot-Arcís, C; Llamas, J M; Cibrian, R; Gandia, J L; Paredes-Gallardo, V

    2017-04-01

    The objective of this study was to compare different cephalometric variables in adult patients with class III malocclusions before and after treatment, in order to determine which variables are indicative of orthodontic camouflage or orthognathic surgery. The cases of 156 adult patients were assessed: 77 treated with orthodontic camouflage and 79 treated with orthodontics and orthognathic surgery. The following cephalometric variables were measured on pre-treatment (T1) and post-treatment (T2) lateral cephalograms: sella-nasion-A-point (SNA), sella-nasion-B-point (SNB), and A-point-nasion-B-point (ANB) angles, Wits appraisal, facial axis angle, mandibular plane angle, upper and lower incisor inclination, and inter-incisal angle. There were statistically significant differences in cephalometric variables before and after treatment between the two groups. The percentage of normal pre-treatment measurements in the camouflage orthodontics group was 30.7%, which worsened slightly to 28.4% post-treatment. However in the group receiving surgery, this was 24.5% pre-treatment, improving to 33.5% after surgery. SNA, SNB, Wits appraisal, lower incisor inclination, and inter-incisal angle showed differences between the two groups before and after treatment. Wits appraisal, lower incisor inclination, and inter-incisal angle were indicative of one or other treatment. Upper and lower incisor decompensation in both groups did not reach ideal values, which impeded complete skeletal correction in 52% of surgical cases. Copyright © 2016 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  8. Solvent effects on extraction of aluminum(III), gallium(III), and indium(III), with decanoic acid

    International Nuclear Information System (INIS)

    Yamada, Hiromichi; Hayashi, Hisao; Fujii, Yukio; Mizuta, Masateru

    1986-01-01

    Extraction of aluminum(III) and indium(III) with decanoic acid in 1-octanol was carried out at 25 deg C and at an aqueous ionic strength of 0.1 mol dm -3 (NaClO 4 ). Monomeric and tetrameric aluminum(III) decanoates and monomeric indium(III) decanoate are responsible for the extraction. From a comparison of the present results with those obtained from the previous works, the polymerization of the extracted species was found to be more extensive in benzene than in 1-octanol, and the metal decanoates were highly polymerized in the following order in both solvents: Al > Ga > In. (author)

  9. Spectroscopic investigations on the complexation of Cm(III) and Eu(III) with organic model ligands and their binding mode in human urine (in vitro); Spektroskopische Untersuchungen zur Komplexbildung von Cm(III) und Eu(III) mit organischen Modellliganden sowie ihrer chemischen Bindungsform in menschlichem Urin (in vitro)

    Energy Technology Data Exchange (ETDEWEB)

    Heller, Anne

    2011-10-26

    In case of incorporation, trivalent actinides (An(III)) and lanthanides (Ln(III)) pose a serious health risk to humans. An(III) are artificial, highly radioactive elements which are mainly produced during the nuclear fuel cycle in nuclear power plants. Via hazardous accidents or nonprofessional storage of radioactive waste, they can be released in the environment and enter the human food chain. In contrast, Ln(III) are nonradioactive, naturally occurring elements with multiple applications in technique and medicine. Consequently it is possible that humans get in contact and incorporate both, An(III) and Ln(III). Therefore, it is of particular importance to elucidate the behaviour of these elements in the human body. While macroscopic processes such as distribution, accumulation and excretion are studied quite well, knowledge about the chemical binding form (speciation) of An(III) and Ln(III) in various body fluids is still sparse. In the present work, for the first time, the speciation of Cm(III) and Eu(III) in natural human urine (in vitro) has been investigated spectroscopically and the formed complex identified. For this purpose, also basic investigations on the complex formation of Cm(III) and Eu(III) in synthetic model urine as well as with the urinary relevant, organic model ligands urea, alanine, phenylalanine, threonine and citrate have been performed and the previously unknown complex stability constants determined. Finally, all experimental results were compared to literature data and predictions calculated by thermodynamic modelling. Since both, Cm(III) and Eu(III), exhibit unique luminescence properties, particularly the suitability of time-resolved laser-induced fluorescence spectroscopy (TRLFS) could be demonstrated as a method to investigate these metal ions in untreated, complex biofluids. The results of this work provide new scientific findings on the biochemical reactions of An(III) and Ln(III) in human body fluids on a molecular scale and

  10. 9,10-phenanthrenesemiquinone radical complexes of ruthenium(III), osmium(III) and rhodium(III) and redox series.

    Science.gov (United States)

    Biswas, Manas Kumar; Patra, Sarat Chandra; Maity, Amarendra Nath; Ke, Shyue-Chu; Weyhermüller, Thomas; Ghosh, Prasanta

    2013-05-14

    Reactions of 9,10-phenanthrenequinone (PQ) in toluene with [M(II)(PPh3)3X2] at 298 K afford green complexes, trans-[M(PQ)(PPh3)2X2] (M = Ru, X = Cl, 1; M = Os, X = Br, 2) in moderate yields. Reaction of anhydrous RhCl3 with PQ and PPh3 in boiling ethanol affords the dark brown paramagnetic complex, cis-[Rh(PQ)(PPh3)2Cl2] (3) in good yields. Diffusion of iodine solution in n-hexane to the trans-[Os(PQ) (PPh3)2(CO)(Br)] solution in CH2Cl2 generates the crystals of trans-[Os(PQ)(PPh3)2(CO)(Br)](+)I3(-), (4(+))I3(-)), in lower yields. Single crystal X-ray structure determinations of 1·2toluene, 2·CH2Cl2 and 4(+)I3(-), UV-vis/NIR absorption spectra, EPR spectra of 3, electrochemical activities and DFT calculations on 1, 2, trans-[Ru(PQ)(PMe3)2Cl2] (1Me), trans-[Os(PQ)(PMe3)2Br2] (2Me), cis-[Rh(PQ)(PMe3)2Cl2] (3Me) and their oxidized and reduced analogues including trans-[Os(PQ)(PMe3)2(CO)(Br)](+) (4Me(+)) substantiated that 1-3 are the 9,10-phenanthrenesemiquinone radical (PQ(˙-)) complexes of ruthenium(III), osmium(III) and rhodium(III) and are defined as trans/cis-[M(III)(PQ(˙-))(PPh3)2X2] with a minor contribution of the resonance form trans/cis-[M(II)(PQ)(PPh3)2X2]. Two comparatively longer C-O (1.286(4) Å) and the shorter C-C lengths (1.415(7) Å) of the OO-chelate of 1·2toluene and 2·CH2Cl2 and the isotropic fluid solution EPR signal at g = 1.999 of 3 are consistent with the existence of the reduced PQ(˙-) ligand in 1-3 complexes. Anisotropic EPR spectra of the frozen glasses (g11 = g22 = 2.0046 and g33 = 1.9874) and solids (g11 = g22 = 2.005 and g33 = 1.987) instigate the contribution of the resonance form, cis-[Rh(II)(PQ)(PPh3)2Cl2] in 3. DFT calculations established that the closed shell singlet (CSS) solutions of 1Me and 2Me are unstable due to open shell singlet (OSS) perturbation. However, the broken symmetry (BS) (1,1) Ms = 0 solutions of 1Me and 2Me are respectively 22.6 and 24.2 kJ mole(-1) lower in energy and reproduced the experimental bond

  11. Classification of pediatric functional gastrointestinal disorders related to abdominal pain using Rome III vs. Rome IV criterions.

    Science.gov (United States)

    Edwards, Trent; Friesen, Craig; Schurman, Jennifer V

    2018-03-17

    The primary purpose of this study was to compare Rome III and IV evaluation criteria for irritable bowel syndrome (IBS), functional dyspepsia (FD), and an overlap syndrome consisting of both IBS and FD by assessing the frequency of each diagnosis in a population of children with chronic abdominal pain. Frequencies of Rome IV FD subtypes of postprandial distress syndrome (PDS) and epigastric pain syndrome (EPS) were determined and FD/IBS overlap symptom associations were also assessed. We conducted a cross-sectional retrospective chart review of 106 pediatric patients who had completed standardized medical histories as part of their evaluation for chronic abdominal pain. The patients ranged from eight to 17 years of age and reported having abdominal pain at least weekly for 8 weeks. Patients whose evaluation revealed gastrointestinal disease were excluded. The patients' diagnoses were determined by a single pediatric gastroenterologist utilizing the specific criteria for Rome III and IV, respectively. Patients were significantly more likely to be diagnosed with FD (84.9% vs. 52.8%), IBS (69.8% vs. 34%), and FD/IBS overlap (58.5% vs. 17.9%) by Rome IV criteria, as compared to Rome III criteria. With regard to Rome IV FD subtypes, 81.1% fulfilled criteria for PDS, 11.1% fulfilled criteria for EPS, 6.7% fulfilled criteria for both, and 1.1% did not fulfill criteria for either. Finally, we found an increased frequency of diarrhea and pain with eating in the overlap group compared to the non-overlap group of Rome III, while only an increased frequency of diarrhea was found in the overlap group compared to the non-overlap group of Rome IV. Our data demonstrate that utilizing Rome IV criteria, as compared to Rome III, results in an increase in the diagnosis of FD, a two-fold increase in the diagnosis of IBS, and a three-fold increase in the diagnosis of FD/IBS overlap. Rome IV criteria appears to result in greater heterogeneity within diagnostic categories. It is important

  12. Conservative treatment of Angle Class III malocclusion with anterior crossbite

    Directory of Open Access Journals (Sweden)

    João Hélder Ferreira de Aguiar

    2015-08-01

    Full Text Available Angle Class III malocclusion is characterized by anteroposterior dental discrepancy which might be associated or not with skeletal changes. Class III molar relationship is associated with vertical or lingually tipped mandibular incisors and a usually concave profile. These characteristics seriously affect facial esthetics and most frequently are the reason why patients seek orthodontic treatment. This case was presented to the committee of the Brazilian Board of Orthodontics and Facial Orthopedics (BBO as part of the requisites to become a BBO Diplomate.

  13. Verification of the DUCT-III for calculation of high energy neutron streaming

    Energy Technology Data Exchange (ETDEWEB)

    Masukawa, Fumihiro; Nakano, Hideo; Nakashima, Hiroshi; Sasamoto, Nobuo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Tayama, Ryu-ichi; Handa, Hiroyuki; Hayashi, Katsumi [Hitachi Engineering Co., Ltd., Hitachi, Ibaraki (Japan); Hirayama, Hideo [High Energy Accelerator Research Organization, Tsukuba, Ibaraki (Japan); Shin, Kazuo [Kyoto Univ., Kyoto (Japan)

    2003-03-01

    A large number of radiation streaming calculations under a variety of conditions are required as a part of shielding design for a high energy proton accelerator facility. Since sophisticated methods are very time consuming, simplified methods are employed in many cases. For accuracy evaluation of a simplified code DUCT-III for high energy neutron streaming calculations, two kinds of benchmark problems based on the experiments were analyzed. Through comparison of the DUCT-III calculations with both the measurements and the sophisticated Monte Carlo calculations, DUCT-III was seen reliable enough for applying to the shielding design for the Intense Proton Accelerator Facility. (author)

  14. Verification of the DUCT-III for calculation of high energy neutron streaming

    CERN Document Server

    Masukawa, F; Hayashi, K; Hirayama, H; Nakano, H; Nakashima, H; Sasamoto, N; Shin, K; Tayama, R I

    2003-01-01

    A large number of radiation streaming calculations under a variety of conditions are required as a part of shielding design for a high energy proton accelerator facility. Since sophisticated methods are very time consuming, simplified methods are employed in many cases. For accuracy evaluation of a simplified code DUCT-III for high energy neutron streaming calculations, two kinds of benchmark problems based on the experiments were analyzed. Through comparison of the DUCT-III calculations with both the measurements and the sophisticated Monte Carlo calculations, DUCT-III was seen reliable enough for applying to the shielding design for the Intense Proton Accelerator Facility.

  15. Comparative Genomics Identifies a Novel Conserved Protein, HpaT, in Proteobacterial Type III Secretion Systems that Do Not Possess the Putative Translocon Protein HrpF

    Directory of Open Access Journals (Sweden)

    Céline Pesce

    2017-06-01

    Full Text Available Xanthomonas translucens is the causal agent of bacterial leaf streak, the most common bacterial disease of wheat and barley. To cause disease, most xanthomonads depend on a highly conserved type III secretion system, which translocates type III effectors into host plant cells. Mutagenesis of the conserved type III secretion gene hrcT confirmed that the X. translucens type III secretion system is required to cause disease on the host plant barley and to trigger a non-host hypersensitive response (HR in pepper leaves. Type III effectors are delivered to the host cell by a surface appendage, the Hrp pilus, and a translocon protein complex that inserts into the plant cell plasma membrane. Homologs of the Xanthomonas HrpF protein, including PopF from Ralstonia solanacearum and NolX from rhizobia, are thought to act as a translocon protein. Comparative genomics revealed that X. translucens strains harbor a noncanonical hrp gene cluster, which rather shares features with type III secretion systems from Ralstonia solanacearum, Paraburkholderia andropogonis, Collimonas fungivorans, and Uliginosibacterium gangwonense than other Xanthomonas spp. Surprisingly, none of these bacteria, except R. solanacearum, encode a homolog of the HrpF translocon. Here, we aimed at identifying a candidate translocon from X. translucens. Notably, genomes from strains that lacked hrpF/popF/nolX instead encode another gene, called hpaT, adjacent to and co-regulated with the type III secretion system gene cluster. An insertional mutant in the X. translucens hpaT gene, which is the first gene of a two-gene operon, hpaT-hpaH, was non-pathogenic on barley and did not cause the HR or programmed cell death in non-host pepper similar to the hrcT mutant. The hpaT mutant phenotypes were partially complemented by either hpaT or the downstream gene, hpaH, which has been described as a facilitator of translocation in Xanthomonas oryzae. Interestingly, the hpaT mutant was also complemented

  16. Predicting Efficient Antenna Ligands for Tb(III) Emission

    Energy Technology Data Exchange (ETDEWEB)

    Samuel, Amanda P.S.; Xu, Jide; Raymond, Kenneth

    2008-10-06

    A series of highly luminescent Tb(III) complexes of para-substituted 2-hydroxyisophthalamide ligands (5LI-IAM-X) has been prepared (X = H, CH{sub 3}, (C=O)NHCH{sub 3}, SO{sub 3}{sup -}, NO{sub 2}, OCH{sub 3}, F, Cl, Br) to probe the effect of substituting the isophthalamide ring on ligand and Tb(III) emission in order to establish a method for predicting the effects of chromophore modification on Tb(III) luminescence. The energies of the ligand singlet and triplet excited states are found to increase linearly with the {pi}-withdrawing ability of the substituent. The experimental results are supported by time-dependent density functional theory (TD-DFT) calculations performed on model systems, which predict ligand singlet and triplet energies within {approx}5% of the experimental values. The quantum yield ({Phi}) values of the Tb(III) complex increases with the triplet energy of the ligand, which is in part due to the decreased non-radiative deactivation caused by thermal repopulation of the triplet. Together, the experimental and theoretical results serve as a predictive tool that can be used to guide the synthesis of ligands used to sensitize lanthanide luminescence.

  17. Efficacy of the semiempirical sparkle model as compared to ECP ab-initio calculations for the prediction of ligand field parameters of europium (III) complexes

    International Nuclear Information System (INIS)

    Freire, Ricardo O.; Rocha, Gerd B.; Albuquerque, Rodrigo Q.; Simas, Alfredo M.

    2005-01-01

    The second version of the sparkle model for the calculation of lanthanide complexes (SMLC II) as well as ab-initio calculations (HF/STO-3G and HF/3-21G) have been used to calculate the geometries of a series of europium (III) complexes with different coordination numbers (CN=7, 8 and 9), ligating atoms (O and N) and ligands (mono, bi and polydentate). The so-called ligand field parameters, Bqk's, have been calculated from both SMLC II and ab-initio optimized structures and compared to the ones calculated from crystallographic data. The results show that the SMLC II model represents a significant improvement over the previous version (SMLC) and has given good results when compared to ab-initio methods, which demand a much higher computational effort. Indeed, ab-initio methods take around a hundred times more computing time than SMLC. As such, our results indicate that our sparkle model can be a very useful and a fast tool when applied to the prediction of both ground state geometries and ligand field parameters of europium (III) complexes

  18. Dopad regulace Basel III na exportní financování

    OpenAIRE

    Malešová, Jana

    2016-01-01

    The thesis focuses on the impact of the banking regulation Basel III on bank-intermediated trade finance. The theoretical part of the thesis explains details of Basel III requirements, history of Basel Accords and their future in the form of Basel IV, characteristics of trade finance products and of the whole industry. Trade finance industry voiced worries about the negative effect that these new requirements might have on trade finance business. The thesis estimates determinants of bank-inte...

  19. Study of irradiated bone: Part III. /sup 99m/Tc pyrophosphate autoradiographic changes

    International Nuclear Information System (INIS)

    King, M.A.; Corriveau, O.; Casarett, G.W.; Weber, D.A.

    1978-01-01

    The macroautoradiographic and microautoradiographic localization of /sup 99m/Tc-pyrophosphate (/sup 99m/TcPPi) was studied in x-irradiated bone of rabbits up to one year post-irradiation. In cortical bone, /sup 99m/TcPPi was concentrated on bone surfaces near vasculature. Both forming and resorbing bone surfaces were comparably labeled at 2 hrs post-injection. Uptake on the surface of sites of haversian bone remodeling was observed to be at least part of the increased /sup 99m/TcPPi observed in irradiated bone in camera images. In irradiated trabecular bone 12 months following irradiation, a patchy decrease in /sup 99m/TcPPi uptake was correlated with localized decreases in vasculature

  20. Structural Properties of the Cr(III)-Fe(III) (Oxy)Hydroxide Compositional Series: Insights for a Nanomaterial 'Solid Solution'

    International Nuclear Information System (INIS)

    Tang, Y.; Zhang, L.; Michel, F.M.; Harrington, R.; Parise, J.B.; Reeder, R.J.

    2010-01-01

    Chromium(III) (oxy)hydroxide and mixed Cr(III)-Fe(III) (oxy)hydroxides are environmentally important compounds for controlling chromium speciation and bioaccessibility in soils and aquatic systems and are also industrially important as precursors for materials and catalyst synthesis. However, direct characterization of the atomic arrangements of these materials is complicated because of their amorphous X-ray properties. This study involves synthesis of the complete Cr(III)-Fe(III) (oxy)hydroxide compositional series, and the use of complementary thermal, microscopic, spectroscopic, and scattering techniques for the evaluation of their structural properties. Thermal analysis results show that the Cr end member has a higher hydration state than the Fe end member, likely associated with the difference in water exchange rates in the first hydration spheres of Cr(III) and Fe(III). Three stages of weight loss are observed and are likely related to the loss of surface/structural water and hydroxyl groups. As compared to the Cr end member, the intermediate composition sample shows lower dehydration temperatures and a higher exothermic transition temperature. XANES analysis shows Cr(III) and Fe(III) to be the dominant oxidation states. XANES spectra also show progressive changes in the local structure around Cr and Fe atoms over the series. Pair distribution function (PDF) analysis of synchrotron X-ray total scattering data shows that the Fe end member is nanocrystalline ferrihydrite with an intermediate-range order and average coherent domain size of ∼27 (angstrom). The Cr end member, with a coherent domain size of ∼10 (angstrom), has only short-range order. The PDFs show progressive structural changes across the compositional series. High-resolution transmission electron microscopy (HRTEM) results also show the loss of structural order with increasing Cr content. These observations provide strong structural evidence of chemical substitution and progressive structural

  1. PIO I-II tendencies case study. Part 1. Mathematical modeling

    Directory of Open Access Journals (Sweden)

    Adrian TOADER

    2010-03-01

    Full Text Available In the paper, a study is performed from the perspective of giving a method to reduce the conservatism of the well known PIO (Pilot-Induced Oscillation criteria in predicting the susceptibility of an aircraft to this very harmful phenomenon. There are three interacting components of a PIO – the pilot, the vehicle, and the trigger (in fact, the hazard. The study, conceived in two parts, aims to underline the importance of human pilot model involved in analysis. In this first part, it is shown, following classical sources, how the LQG theory of control and estimation is used to obtain a complex model of human pilot. The approach is based on the argument, experimentally proved, that the human behaves “optimally” in some sense, subject to his inherent psychophysical limitations. The validation of such model is accomplished based on the experimental model of a VTOL-type aircraft. Then, the procedure of inserting typical saturation nonlinearities in the open loop transfer function is presented. A second part of the paper will illustrate PIO tendencies evaluation by means of a grapho-analytic method.

  2. Synthesis and characterization of La(III), Pr(III), Nd(III), Sm(III), Eu(III), Gd(III), Tb(III) and Dy(III) complexes of 2-acetylfuran-2-thenoylhydrazone

    International Nuclear Information System (INIS)

    Singh, B.; Singh, Praveen K.

    1998-01-01

    The reaction of 2-acetylfuran-2-thenoylhydrazone(afth) with Ln(III) trichlorides yields complexes of the type [Ln(afth)Cl 2 (H 2 O)(EtOH)]Cl, [Ln(III) = La, Pr, Nd, Sm, Eu, Gd, Tb and Dy]. The complexes have been characterized by molar conductance, magnetic susceptibility and TGA and DTA measurements, magnetic susceptibility and TGA and DTA measurements, FAB mass, infrared, proton NMR, electronic absorption and emission spectra. The terbium complex is found to be monomer from the FAB mass spectrum. The IR and NMR spectra suggest neutral tridentate behaviour of the Schiff base. A coordination number seven is proposed around the metal ions. Emission spectra suggest C 3v , symmetry around the metal ion with capped octahedron geometry for the europium complex. (author)

  3. Modelling Eu(III) speciation in a Eu(III)/PAHA/α-Al2O3 ternary system

    International Nuclear Information System (INIS)

    Janot, Noemie; Reiller, Pascal E.; Benedetti, Marc F.

    2013-01-01

    In this work, modelling of Eu(III) speciation in a ternary system, i.e., in presence of purified Aldrich humic acid (PAHA) and α-Al 2 O 3 , is presented. First, the mineral surface charge is measured by potentiometric titrations and then described using the CD-MUSIC model. This model is also used to describe Eu(III) binding to the α-Al 2 O 3 surface at different pH values, ionic strength and mineral concentrations. Time resolved luminescence spectroscopy (TRLS) is then used to study the binding of Eu(III) to PAHA at pH 4 with different humic acid concentrations. The spectra are used to calculate a spectroscopic 'titration curve', used to determine Eu(III)/PAHA binding parameters in the NICA-Donnan model. Following a previous study (Janot et al., Water Res. 46, 731-740), modelling of the ternary system is based upon the definition of two PAHA pools where one fraction remains in solution and the other is adsorbed onto the mineral surface, with each possessing different proton and metal binding parameters. The modification of protonation behaviour for both fractions is examined using spectrophotometric titrations of the non adsorbed PAHA fraction at different organic/mineral ratios. These data are then used to describe Eu(III) interactions in the ternary system: Eu(III) re-partitioning in the ternary system is calculated for different pH, ionic strength and PAHA concentrations, and results are compared to experimental observations. The model is in good agreement with experimental data, except at high PAHA fractionation rates. Results show that organic complexation dominates over a large pH range, with the predominant species existing as the surface-bound fraction. Above pH 8, Eu(III) seems to be mostly complexed to the mineral surface, which is in agreement with previous spectroscopic observations (Janot et al., Environ. Sci. Technol. 45, 3224-3230). (authors)

  4. Probing the magnetic moments of [Mn{sup III}{sub 6}Cr{sup III}]{sup 3+} single-molecule magnets—A cross comparison of XMCD and spin-resolved electron spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Helmstedt, Andreas, E-mail: helmstedt.andreas@gmail.com [Faculty of Physics, Bielefeld University, Universitätsstr. 25, 33615 Bielefeld (Germany); Dohmeier, Niklas; Müller, Norbert; Gryzia, Aaron; Brechling, Armin; Heinzmann, Ulrich [Faculty of Physics, Bielefeld University, Universitätsstr. 25, 33615 Bielefeld (Germany); Hoeke, Veronika; Krickemeyer, Erich; Glaser, Thorsten [Faculty of Chemistry, Bielefeld University, Universitätsstr. 25, 33615 Bielefeld (Germany); Leicht, Philipp; Fonin, Mikhail [Fachbereich Physik, Universität Konstanz, Universitätsstr. 10, 78457 Konstanz (Germany); Tietze, Thomas [Max Planck Institute for Intelligent Systems, Heisenbergstr. 3, 70569 Stuttgart (Germany); Joly, Loïc [Institut de Physique et Chimie des Matériaux de Strasbourg, UMR 7504, CNRS-Université de Strasbourg, BP 43, 23 rue du Loess, F-67034 Strasbourg Cedex 2 (France); Kuepper, Karsten [Institut für Festkörperphysik, Universität Ulm, 89069 Ulm (Germany)

    2015-01-15

    Highlights: • [Mn{sup III}{sub 6}Cr{sup III}]{sup 3+} single-molecule magnets are investigated. • XMCD and spin-resolved electron spectroscopy (SPES) results are compared. • A simple sum rule evaluation is performed for comparison. • Differences between SPES and XMCD results are discussed. • Influences of the magnetic field on the Mn L edge absorption are observed. - Abstract: Single-molecule magnets (SMM) of the [Mn{sup III}{sub 6}Cr{sup III}]{sup 3+} structural type prepared on Si and gold-coated glass substrates have been investigated by spin-resolved electron spectroscopy (SPES) and X-ray magnetic circular dichroism (XMCD) at the Mn L{sub 3,2} edge and in addition by XMCD at the Cr L{sub 3,2} edge using synchrotron radiation. Differences between the two methods are discussed. Despite its severe limitations for 3d transition metals, a spin sum rule evaluation is nevertheless performed for the Mn{sup III} centres in the [Mn{sup III}{sub 6}Cr{sup III}]{sup 3+} SMM to provide a simple means of comparing XMCD and spin-resolved electron spectroscopy results.

  5. Peatlands as Filters for Polluted Mine Water?—A Case Study from an Uranium-Contaminated Karst System in South Africa—Part III: Quantifying the Hydraulic Filter Component

    Directory of Open Access Journals (Sweden)

    Frank Winde

    2011-03-01

    Full Text Available As Part III of a four-part series on the filter function of peat for uranium (U, this paper focuses on the hydraulic component of a conceptual filter model introduced in Part II. This includes the quantification of water flow through the wetland as a whole, which was largely unknown and found to be significantly higher that anticipated. Apart from subaquatic artesian springs associated with the underlying karst aquifer the higher flow volumes were also caused by plumes of polluted groundwater moving laterally into the wetland. Real-time, quasi-continuous in situ measurements of porewater in peat and non-peat sediments indicate that rising stream levels (e.g., during flood conditions lead to the infiltration of stream water into adjacent peat deposits and thus allow for a certain proportion of flood water to be filtered. However, changes in porewater quality triggered by spring rains may promote the remobilization of possibly sorbed U.

  6. Connective tissue-activating peptide III: a novel blood biomarker for early lung cancer detection.

    Science.gov (United States)

    Yee, John; Sadar, Marianne D; Sin, Don D; Kuzyk, Michael; Xing, Li; Kondra, Jennifer; McWilliams, Annette; Man, S F Paul; Lam, Stephen

    2009-06-10

    There are no reliable blood biomarkers to detect early lung cancer. We used a novel strategy that allows discovery of differentially present proteins against a complex and variable background. Mass spectrometry analyses of paired pulmonary venous-radial arterial blood from 16 lung cancer patients were applied to identify plasma proteins potentially derived from the tumor microenvironment. Two differentially expressed proteins were confirmed in 64 paired venous-arterial blood samples using an immunoassay. Twenty-eight pre- and postsurgical resection peripheral blood samples and two independent, blinded sets of plasma from 149 participants in a lung cancer screening study (49 lung cancers and 100 controls) and 266 participants from the National Heart Lung and Blood Institute Lung Health Study (45 lung cancer and 221 matched controls) determined the accuracy of the two protein markers to detect subclinical lung cancer. Connective tissue-activating peptide III (CTAP III)/ neutrophil activating protein-2 (NAP-2) and haptoglobin were identified to be significantly higher in venous than in arterial blood. CTAP III/NAP-2 levels decreased after tumor resection (P = .01). In two independent population cohorts, CTAP III/NAP-2 was significantly associated with lung cancer and improved the accuracy of a lung cancer risk prediction model that included age, smoking, lung function (FEV(1)), and an interaction term between FEV(1) and CTAP III/NAP-2 (area under the curve, 0.84; 95% CI, 0.77 to 0.91) compared to CAPIII/NAP-2 alone. We identified CTAP III/NAP-2 as a novel biomarker to detect preclinical lung cancer. The study underscores the importance of applying blood biomarkers as part of a multimodal lung cancer risk prediction model instead of as stand-alone tests.

  7. Preparation and characterisation of mixed ligand complexes of Co(III), Fe(III) and Cr(III) containing phthalimide and phenols

    International Nuclear Information System (INIS)

    Miah, M.A.J.; Islam, M.S.; Pal, S.C.; Barma, T.K.

    1996-01-01

    Some novel mixed ligand complexes of Co(III), Fe(III) and Cr(III) containing phthalimide as primary and 2-aminophenol and 3-aminophenol as secondary ligands have been synthesized and characterised on the basis of elemental analyses, conductivity and magnetic measurements and infrared and electronic spectral studies. Complexes containing 2-aminophenol are 1:1 electrolyte in N,N dimethylformamide. Spectral studies indicate that all the complexes exhibit octahedral geometry. The complexes have the general composition; K[M(pim)/sub 2/(L)/sub 2/]; where m=Co(III), Fe(III) and Cr(III), pim-anion of phthalimamide and L=anion of 2-aminophenol and 3-aminophenol. (author)

  8. Comparative analysis of the anterior and posterior length and deflection angle of the cranial base, in individuals with facial Pattern I, II and III

    Directory of Open Access Journals (Sweden)

    Guilherme Thiesen

    2013-02-01

    Full Text Available OBJECTIVE: This study evaluated the variations in the anterior cranial base (S-N, posterior cranial base (S-Ba and deflection of the cranial base (SNBa among three different facial patterns (Pattern I, II and III. METHOD: A sample of 60 lateral cephalometric radiographs of Brazilian Caucasian patients, both genders, between 8 and 17 years of age was selected. The sample was divided into 3 groups (Pattern I, II and III of 20 individuals each. The inclusion criteria for each group were the ANB angle, Wits appraisal and the facial profile angle (G'.Sn.Pg'. To compare the mean values obtained from (SNBa, S-N, S-Ba each group measures, the ANOVA test and Scheffé's Post-Hoc test were applied. RESULTS AND CONCLUSIONS: There was no statistically significant difference for the deflection angle of the cranial base among the different facial patterns (Patterns I, II and III. There was no significant difference for the measures of the anterior and posterior cranial base between the facial Patterns I and II. The mean values for S-Ba were lower in facial Pattern III with statistically significant difference. The mean values of S-N in the facial Pattern III were also reduced, but without showing statistically significant difference. This trend of lower values in the cranial base measurements would explain the maxillary deficiency and/or mandibular prognathism features that characterize the facial Pattern III.OBJETIVO: o presente estudo avaliou as variações da base craniana anterior (S-N, base craniana posterior (S-Ba, e ângulo de deflexão da base do crânio (SNBa entre três diferentes padrões faciais (Padrão I, II e III. MÉTODOS: selecionou-se uma amostra de 60 telerradiografias em norma lateral de pacientes brasileiros leucodermas, de ambos os sexos, com idades entre 8 anos e 17 anos. A amostra foi dividida em três grupos (Padrão I, II e III, sendo cada grupo constituído de 20 indivíduos. Os critérios de seleção dos indivíduos para cada grupo

  9. Comparative risk assessment of spill response options for a deepwater oil well blowout: Part III. Stakeholder engagement.

    Science.gov (United States)

    Walker, Ann Hayward; Scholz, Debra; McPeek, Melinda; French-McCay, Deborah; Rowe, Jill; Bock, Michael; Robinson, Hilary; Wenning, Richard

    2018-05-25

    This paper describes oil spill stakeholder engagement in a recent comparative risk assessment (CRA) project that examined the tradeoffs associated with a hypothetical offshore well blowout in the Gulf of Mexico, with a specific focus on subsea dispersant injection (SSDI) at the wellhead. SSDI is a new technology deployed during the Deepwater Horizon (DWH) oil spill response. Oil spill stakeholders include decision makers, who will consider whether to integrate SSDI into future tradeoff decisions. This CRA considered the tradeoffs associated with three sets of response strategies: (1) no intervention; (2) mechanical recovery, in-situ burning, and surface dispersants; and, (3) SSDI in addition to responses in (2). For context, the paper begins with a historical review of U.S. policy and engagement with oil spill stakeholders regarding dispersants. Stakeholder activities throughout the project involved decision-maker representatives and their advisors to inform the approach and consider CRA utility in future oil spill preparedness. Copyright © 2018 Elsevier Ltd. All rights reserved.

  10. Glenoid fossa position in Class III malocclusion associated with mandibular protrusion.

    Science.gov (United States)

    Innocenti, Cristina; Giuntini, Veronica; Defraia, Efisio; Baccetti, Tiziano

    2009-04-01

    Our aim in this study was to investigate the position of the glenoid fossa in subjects with Class III malocclusion associated with mandibular protrusion to better clarify the role of this craniofacial component in Class III skeletal disharmony. A sample of 30 subjects, aged 8 years +/- 6 months, with skeletal and dental Class III malocclusion associated with mandibular protrusion, normal skeletal vertical relationships, and normal mandibular dimensions, was compared with a control group of 33 subjects with skeletal and dental Class I relationships. The comparisons between the Class III group and the control group on the cephalometric measures for the assessment of glenoid fossa position were performed with the Mann-Whitney U test at P <0.05. Subjects with Class III malocclusion had a significantly more mesial position of the glenoid fossa, when compared with the control group as measured with 3 parameters. An anterior position of the glenoid fossa is a possible diagnostic anatomic feature of Class III malocclusion associated with mandibular protrusion. An effective measurement to evaluate glenoid fossa position in craniofacial relationships is the cephalometric distance from the glenoid fossa to the frontomaxillary-nasal suture.

  11. A user's perspective on the merits and shortcomings of ASME Section III

    International Nuclear Information System (INIS)

    Antaki, G.A.

    1994-01-01

    There are several aspects of Section III which when compared to process industry codes (ASME VIII, ASME B31.3, API, etc.) have proven to be a significant improvement in engineering practice. There are, however, other aspects of ASME III which have added to costs without clear benefits in safety or reliability. The authors present a user's perspective on some of the relative merits and shortcomings of the nuclear codes (ASME III and XI) compared to the process industry codes (such as ASME VIII, B31.3 and API)

  12. Comparative analysis of the nuclear lens opalescence by the Lens Opacities Classification System III with nuclear density values provided by Oculus Pentacam: a cross-section study using Pentacam Nucleus Staging software.

    Science.gov (United States)

    Magalhães, Fernanda Pedreira; Costa, Elaine Fiod; Cariello, Angelino Júlio; Rodrigues, Eduardo Buchele; Hofling-Lima, Ana Luisa

    2011-01-01

    To compare the clinical classification of cataract using the Lens Opacities Classification System (LOCS) III with the mean values of lens density provided by the Pentacam Scheimpflug System in nuclear cataracts. One hundred and one eyes from 101 patients with age-related nuclear cataract were submitted to clinical examination for lens grading score using LOCS III. According to LOCS III, nuclear opalescence was divided in six groups. Patients were evaluated by the Pentacam Scheimpflug System for the mean lens density using the Pentacam lens densitometry program (PLDP), the Pentacam Nucleus Staging (PNS) mean value and the PNS cataract grading score. A positive correlation between the mean values of lens density and LOCS III classification, considering groups 1 to 5, could be noticed with PLDP and PNS mean value. The mean values between the groups were similar using the PLDP and the PNS mean value. However, when the PNS cataract grading score was evaluated, there was low correspondence with LOCS III classification. Pentacam Scheimpflug device offers an objective measure of the lens nuclear density on nuclear cataracts. PLDP and the PNS mean value were both useful to evaluate age-related nuclear cataract up to LOCS III group 5.

  13. Nitrile hydration by thiolate- and alkoxide-ligated Co-NHase analogues. Isolation of Co(III)-amidate and Co(III)-iminol intermediates.

    Science.gov (United States)

    Swartz, Rodney D; Coggins, Michael K; Kaminsky, Werner; Kovacs, Julie A

    2011-03-23

    Nitrile hydratases (NHases) are thiolate-ligated Fe(III)- or Co(III)-containing enzymes, which convert nitriles to the corresponding amide under mild conditions. Proposed NHase mechanisms involve M(III)-NCR, M(III)-OH, M(III)-iminol, and M(III)-amide intermediates. There have been no reported crystallographically characterized examples of these key intermediates. Spectroscopic and kinetic data support the involvement of a M(III)-NCR intermediate. A H-bonding network facilitates this enzymatic reaction. Herein we describe two biomimetic Co(III)-NHase analogues that hydrate MeCN, and four crystallographically characterized NHase intermediate analogues, [Co(III)(S(Me2)N(4)(tren))(MeCN)](2+) (1), [Co(III)(S(Me2)N(4)(tren))(OH)](+) (3), [Co(III)(S(Me2)N(4)(tren))(NHC(O)CH(3))](+) (2), and [Co(III)(O(Me2)N(4)(tren))(NHC(OH)CH(3))](2+) (5). Iminol-bound 5 represents the first example of a Co(III)-iminol compound in any ligand environment. Kinetic parameters (k(1)(298 K) = 2.98(5) M(-1) s(-1), ΔH(‡) = 12.65(3) kcal/mol, ΔS(‡) = -14(7) e.u.) for nitrile hydration by 1 are reported, and the activation energy E(a) = 13.2 kcal/mol is compared with that (E(a) = 5.5 kcal/mol) of the NHase enzyme. A mechanism involving initial exchange of the bound MeCN for OH- is ruled out by the fact that nitrile exchange from 1 (k(ex)(300 K) = 7.3(1) × 10(-3) s(-1)) is 2 orders of magnitude slower than nitrile hydration, and that hydroxide bound 3 does not promote nitrile hydration. Reactivity of an analogue that incorporates an alkoxide as a mimic of the highly conserved NHase serine residue shows that this moiety facilitates nitrile hydration under milder conditions. Hydrogen-bonding to the alkoxide stabilizes a Co(III)-iminol intermediate. Comparison of the thiolate versus alkoxide intermediate structures shows that C≡N bond activation and C═O bond formation proceed further along the reaction coordinate when a thiolate is incorporated into the coordination sphere.

  14. Distributed inter process communication framework of BES III DAQ online software

    International Nuclear Information System (INIS)

    Li Fei; Liu Yingjie; Ren Zhenyu; Wang Liang; Chinese Academy of Sciences, Beijing; Chen Mali; Zhu Kejun; Zhao Jingwei

    2006-01-01

    DAQ (Data Acquisition) system is one important part of BES III, which is the large scale high-energy physics detector on the BEPC. The inter process communication (IPC) of online software in distributed environments is very pivotal for design and implement of DAQ system. This article will introduce one distributed inter process communication framework, which is based on CORBA and used in BES III DAQ online software. The article mainly presents the design and implementation of the IPC framework and application based on IPC. (authors)

  15. Basel III : how have banks adjusted to increase CET1 ratios?

    OpenAIRE

    Bjerketvedt, Oda; Arneberg-Bauer, Tonje

    2013-01-01

    In 2010 the Basel Committee finalised the global framework called Basel III, which will have a significant impact on the global banking sector. A large part of the framework focuses on capital adequacy, where the Common Equity Tier 1 (CET1) ratio is essential. Through an analysis of four banks from the United Kingdom – HSBC, Barclays, Lloyds Banking Group and Standard Chartered – this thesis aim to examine how these banks have adjusted to the new CET1 requirements. In the EU the Basel III ...

  16. Interpretation of recovery stage III in gold. [Electron irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Seeger, A.; Frank, W. (Max-Planck-Institut fuer Metallforschung, Stuttgart (Germany, F.R.). Inst. fuer Physik; Stuttgart Univ. (Germany, F.R.). Inst. fuer Theoretische und Angewandte Physik)

    1983-05-01

    The paper compares a recent investigation of Stage-III recovery on electron-irradiated gold by Sonnenberg and Dedek with earlier work on cold-worked or quenched gold. The experimental results of Sonnenberg and Dedek are found to be in excellent agreement with those of Schuele, Seeger, Schumacher, and King, who showed that in Au Stage III is due to the migration of an elementary intrinsic point defect with migration enthalpy Hsup(III) = (0.71 +- 0.02)eV. Since the monovacancy migration enthalpy Hsub(IVsup(M)) = (0.83 +- 0.02)eV obtained by Schuele et al. has been confirmed by other workers and independent techniques, it is concluded that Hsup(III) represents the migration enthalpy of isolated self-interstitials.

  17. Preoperative Quantitative MR Tractography Compared with Visual Tract Evaluation in Patients with Neuropathologically Confirmed Gliomas Grades II and III: A Prospective Cohort Study

    International Nuclear Information System (INIS)

    Delgado, Anna F.; Nilsson, Markus; Latini, Francesco; Mårtensson, Johanna; Zetterling, Maria; Berntsson, Shala G.; Alafuzoff, Irina; Lätt, Jimmy; Larsson, Elna-Marie

    2016-01-01

    Background and Purpose. Low-grade gliomas show infiltrative growth in white matter tracts. Diffusion tensor tractography can noninvasively assess white matter tracts. The aim was to preoperatively assess tumor growth in white matter tracts using quantitative MR tractography (3T). The hypothesis was that suspected infiltrated tracts would have altered diffusional properties in infiltrated tract segments compared to noninfiltrated tracts. Materials and Methods. Forty-eight patients with suspected low-grade glioma were included after written informed consent and underwent preoperative diffusion tensor imaging in this prospective review-board approved study. Major white matter tracts in both hemispheres were tracked, segmented, and visually assessed for tumor involvement in thirty-four patients with gliomas grade II or III (astrocytomas or oligodendrogliomas) on postoperative neuropathological evaluation. Relative fractional anisotropy (rFA) and mean diffusivity (rMD) in tract segments were calculated and compared with visual evaluation and neuropathological diagnosis. Results. Tract segment infiltration on visual evaluation was associated with a lower rFA and high rMD in a majority of evaluated tract segments (89% and 78%, resp.). Grade II and grade III gliomas had similar infiltrating behavior. Conclusion. Quantitative MR tractography corresponds to visual evaluation of suspected tract infiltration. It may be useful for an objective preoperative evaluation of tract segment involvement

  18. Thermodynamic data for predicting concentrations of Pu(III), Am(III), and Cm(III) in geologic environments

    Energy Technology Data Exchange (ETDEWEB)

    Rai, Dhanpat; Rao, Linfeng; Weger, H.T.; Felmy, A.R. [Pacific Northwest National Laboratory, WA (United States); Choppin, G.R. [Florida State University, Florida (United States); Yui, Mikazu [Japan Nuclear Cycle Development Inst., Tokai Works, Tokai, Ibaraki (Japan)

    1999-01-01

    This report provides thermodynamic data for predicting concentrations of Pu(III), Am(III), and Cm(III) in geologic environments, and contributes to an integration of the JNC chemical thermodynamic database, JNC-TDB (previously PNC-TDB), for the performance analysis of geological isolation system for high-level radioactive wastes. Thermodynamic data for the formation of complexes or compounds with hydroxide, chloride, fluoride, carbonate, nitrate, sulfate and phosphate are discussed in this report. Where data for specific actinide(III) species are lacking, the data were selected based on chemical analogy to other trivalent actinides. In this study, the Pitzer ion-interaction model is mainly used to extrapolate thermodynamic constants to zero ionic strength at 25degC. (author)

  19. Intensity of adjuvant chemotherapy regimens and grade III-V toxicities among elderly stage III colon cancer patients.

    Science.gov (United States)

    van Erning, F N; Razenberg, L G E M; Lemmens, V E P P; Creemers, G J; Pruijt, J F M; Maas, H A A M; Janssen-Heijnen, M L G

    2016-07-01

    The aim of this study was to provide insight in the use, intensity and toxicity of therapy with capecitabine and oxaliplatin (CAPOX) and capecitabine monotherapy (CapMono) among elderly stage III colon cancer patients treated in everyday clinical practice. Data from the Netherlands Cancer Registry were used. All stage III colon cancer patients aged ≥70 years diagnosed in the southeastern part between 2005 and 2012 and treated with CAPOX or CapMono were included. Differences in completion of all planned cycles, cumulative dosages and toxicity between both regimens were evaluated. One hundred ninety-three patients received CAPOX and 164 patients received CapMono; 33% (n = 63) of the patients receiving CAPOX completed all planned cycles of both agents, whereas 55% (n = 90) of the patients receiving CapMono completed all planned cycles (P characteristics, CapMono was associated with a lower odds of developing grade III-V toxicity than CAPOX (odds ratio 0.54, 95% confidence interval 0.33-0.89). For patients treated with CAPOX, the most common toxicities were gastrointestinal (29%), haematological (14%), neurological (11%) and other toxicity (13%). For patients treated with CapMono, dermatological (17%), gastrointestinal (13%) and other toxicity (11%) were the most common. CAPOX is associated with significantly more grade III-V toxicities than CapMono, which had a pronounced impact on the cumulative dosage received and completion of all planned cycles. In this light, CapMono seems preferable over CAPOX. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Luminescence study on solvation of americium(III), curium(III) and several lanthanide(III) ions in nonaqueous and binary mixed solvents

    International Nuclear Information System (INIS)

    Kimura, T.; Nagaishi, R.; Kato, Y.; Yoshida, Z.

    2001-01-01

    The luminescence lifetimes of An(III) and Ln(III) ions [An=Am and Cm; Ln=Nd, Sm, Eu, Tb and Dy] were measured in dimethyl sulfoxide(DMSO), N,N-dimethylformamide(DMF), methanol(MeOH), water and their perdeuterated solvents. Nonradiative decay rates of the ions were in the order of H 2 O > MeOH > DMF > DMSO, indicating that O-H vibration is more effective quencher than C-H, C=O, and S=O vibrations in the solvent molecules. Maximal lifetime ratios τ D /τ H were observed for Eu(III) in H 2 O, for Sm(III) in MeOH and DMF, and for Sm(III) and Dy(III) in DMSO. The solvent composition in the first coordination sphere of Cm(III) and Ln(III) in binary mixed solvents was also studied by measuring the luminescence lifetime. Cm(III) and Ln(III) were preferentially solvated by DMSO in DMSO-H 2 O, by DMF in DMF-H 2 O, and by H 2 O in MeOH-H 2 O over the whole range of the solvent composition. The order of the preferential solvation, i.e., DMSO > DMF > H 2 O > MeOH, correlates with the relative basicity of these solvents. The Gibbs free energy of transfer of ions from water to nonaqueous solvents was further estimated from the degree of the preferential solvation. (orig.)

  1. Luminescence studies of Sm(III) and Cm(III) complexes in NaSCN/DHDECMP extraction systems

    CERN Document Server

    Chung, D Y; Kimura, T

    1999-01-01

    Laser-induced fluorescence (LIF) studies of Sm(III) and Cm(III) complexes in the NaSCN/DHDECMP solvent extraction system were carried out. Luminescence lifetimes were measured to determine the number of water molecules coordinated to Sm(III), Tb(III), Dy(III), and Cm(III) in the sodium thiocyanate solution and in the DHDECMP phase. The hydration number of Sm(III), Tb(III), Dy(III), and Cm(III) in the sodium thiocyanate solution decreased linearly with increasing sodium thiocyanate concentration. The hydration numbers of Sm(III), Dy(III), and Cm(III) in the DHDECMP phase decreased with increasing sodium thiocyanate concentration. The water molecules in the inner coordination sphere of Sm(III) and Dy(III) extracted into the DHDECMP were not completely removed at low sodium thiocyanate concentration but decreased with increasing sodium thiocyanate concentration. However, in the case of Cm(III) extracted into the DHDECMP phase from the sodium thiocyanate solution, there was no water in the inner coordination sphe...

  2. Improving Hybrid III injury assessment in steering wheel rim to chest impacts using responses from finite element Hybrid III and human body model.

    Science.gov (United States)

    Holmqvist, Kristian; Davidsson, Johan; Mendoza-Vazquez, Manuel; Rundberget, Peter; Svensson, Mats Y; Thorn, Stefan; Törnvall, Fredrik

    2014-01-01

    The main aim of this study was to improve the quality of injury risk assessments in steering wheel rim to chest impacts when using the Hybrid III crash test dummy in frontal heavy goods vehicle (HGV) collision tests. Correction factors for chest injury criteria were calculated as the model chest injury parameter ratios between finite element (FE) Hybrid III, evaluated in relevant load cases, and the Total Human Model for Safety (THUMS). This is proposed to be used to compensate Hybrid III measurements in crash tests where steering wheel rim to chest impacts occur. The study was conducted in an FE environment using an FE-Hybrid III model and the THUMS. Two impactor shapes were used, a circular hub and a long, thin horizontal bar. Chest impacts at velocities ranging from 3.0 to 6.0 m/s were simulated at 3 impact height levels. A ratio between FE-Hybrid III and THUMS chest injury parameters, maximum chest compression C max, and maximum viscous criterion VC max, were calculated for the different chest impact conditions to form a set of correction factors. The definition of the correction factor is based on the assumption that the response from a circular hub impact to the middle of the chest is well characterized and that injury risk measures are independent of impact height. The current limits for these chest injury criteria were used as a basis to develop correction factors that compensate for the limitations in biofidelity of the Hybrid III in steering wheel rim to chest impacts. The hub and bar impactors produced considerably higher C max and VC max responses in the THUMS compared to the FE-Hybrid III. The correction factor for the responses of the FE-Hybrid III showed that the criteria responses for the bar impactor were consistently overestimated. Ratios based on Hybrid III and THUMS responses provided correction factors for the Hybrid III responses ranging from 0.84 to 0.93. These factors can be used to estimate C max and VC max values when the Hybrid III is

  3. Effect of Class III bone anchor treatment on airway.

    Science.gov (United States)

    Nguyen, Tung; De Clerck, Hugo; Wilson, Michael; Golden, Brent

    2015-07-01

    To compare airway volumes and minimum cross-section area changes of Class III patients treated with bone-anchored maxillary protraction (BAMP) versus untreated Class III controls. Twenty-eight consecutive skeletal Class III patients between the ages of 10 and 14 years (mean age, 11.9 years) were treated using Class III intermaxillary elastics and bilateral miniplates (two in the infra-zygomatic crests of the maxilla and two in the anterior mandible). The subjects had cone beam computed tomographs (CBCTs) taken before initial loading (T1) and 1 year out (T2). Twenty-eight untreated Class III patients (mean age, 12.4 years) had CBCTs taken and cephalograms generated. The airway volumes and minimum cross-sectional area measurements were performed using Dolphin Imaging 11.7 3D software. The superior border of the airway was defined by a plane that passes through the posterior nasal spine and basion, while the inferior border included the base of the epiglottis to the lower border of C3. From T1 to T2, airway volume from BAMP-treated subjects showed a statistically significant increase (1499.64 mm(3)). The area in the most constricted section of the airway (choke point) increased slightly (15.44 mm(2)). The airway volume of BAMP patients at T2 was 14136.61 mm(3), compared with 14432.98 mm(3) in untreated Class III subjects. Intraexaminer correlation coefficients values and 95% confidence interval values were all greater than .90, showing a high degree of reliability of the measurements. BAMP treatment did not hinder the development of the oropharynx.

  4. Association of Eu(III) and Cm(III) with Bacillus subtilis and Halobacterium salinarum

    International Nuclear Information System (INIS)

    Ozaki, Takuo; Kimura, Takaumi; Ohnuki, Toshihiko; Yoshida, Zenko

    2002-01-01

    Adsorption behavior of Eu(III) and Cm(III) by Bacillus subtilis and Halobacterium salinarum was investigated. Both microorganisms showed almost identical pH dependence on the distribution ratio (K d ) of the metals examined, i.e., K d of Eu(III) and Cm(III) increased with an increase of pH. The coordination state of Eu(III) adsorbed on the microorganisms was studied by time-resolved laser-induced fluorescence spectroscopy (TRLFS). The coordination states of Eu(III) adsorbed on the B. subtilis and H. salinarum was of different characteristics. H. salinarum exhibited more outer-spherical interaction with Eu(III) than B. subtilis. (author)

  5. DESY III, the new proton injector for HERA

    International Nuclear Information System (INIS)

    Hemmie, G.; Maidment, J.R.

    1987-01-01

    The design of a 7.5 GeV/c proton synchrotron, DESY III, which will form part of the injector chain for HERA /1/ is described. Features of the latice and brief details of sub-systems are presented. A selection of parameters and expected time schedule for the accelerator which is at present under construction at the DESY laboratory, Hamburg, are given

  6. Comparing predictors of part-time and no vocational engagement in youth primary mental health services: A brief report.

    Science.gov (United States)

    Cairns, Alice J; Kavanagh, David J; Dark, Frances; McPhail, Steven M

    2017-05-19

    This investigation aims to identify if correlates of not working or studying were also correlated with part-time vocational participation. Demographic and vocational engagement information was collected from 226 participant clinical charts aged 15 to 25 years accessing a primary youth health clinic. Multinomial logistic regressions were used to examine potential correlates no and part-time vocational engagement compared to those full-time. A total of 33% were not working or studying and 19% were part-time. Not working or studying was associated with secondary school dropout and a history of drug use. These associations were not observed in those participating part-time. This result suggests that the markers of disadvantage observed in those not working or studying do not carry over to those who are part-time. Potentially, those who are part-time are less vulnerable to long-term disadvantage compared to their unemployed counterparts as they do not share the same indicators of disadvantage. © 2017 John Wiley & Sons Australia, Ltd.

  7. 34 CFR Appendix B to Part 403 - Examples for 34 CFR 403.194-Comparability Requirements

    Science.gov (United States)

    2010-07-01

    ... 34 Education 3 2010-07-01 2010-07-01 false Examples for 34 CFR 403.194-Comparability Requirements... TECHNOLOGY EDUCATION PROGRAM Pt. 403, App. B Appendix B to Part 403—Examples for 34 CFR 403.194—Comparability... requirements in 34 CFR 403.194(a) include the following: Example 1: The local educational agency files with the...

  8. Stable Solar-Blind Ultraviolet III-Nitride Photocathode for Astronomy Applications

    Science.gov (United States)

    Bell, Lloyd

    In this effort, we propose to develop a new type of cesium-free photocathode using III- nitride materials (GaN, AlN, and their alloys) to achieve highly efficient, solar blind, and stable ultraviolet (UV) response. Currently, detectors used in UV instruments utilize a photocathode to convert UV photons into electrons that are subsequently detected by microchannel plate or CCD. The performance of these detectors critically depends on the efficiency and stability of their photocathodes. In particular, photocathode instability is responsible for many of the fabrication difficulties commonly experienced with this class of detectors. In recent years, III-nitride (in particular GaN) photocathodes have been demonstrated with very high quantum efficiency (>50%) in parts of UV spectral range; however, these photocathodes still rely on cesiation for activation. The proposed photocathode structure will achieve activation through methods for band structure engineering such as delta- doping and polarization field engineering. Compared to the current state-of-the-art in flight-ready microchannel plate/Cs2Te sealed tubes, photocathodes based on III-nitride materials will increase the quantum efficiency by nearly an order of magnitude and significantly enhance both fabrication yield and reliability, since they will not require cesium or other highly reactive materials for activation. This performance will enable a next-generation UV spectroscopic and imaging mission that is of high scientific priority for NASA. This photocathode uses near-surface band-structure engineering to create a permanently activated surface, with high efficiency and air-stable UV response. We will combine this III-nitride structure with our unique III-nitride processing technology to optimize the efficiency and uniformity of the photocathode. In addition, through our design, growth, and processing techniques, we will extend the application of these photocathodes into far UV for both semitransparent and

  9. Improved Antileishmanial Activity of Dppz through Complexation with Antimony(III and Bismuth(III: Investigation of the Role of the Metal

    Directory of Open Access Journals (Sweden)

    Cynthia Demicheli

    2012-10-01

    Full Text Available Two novel trivalent antimony(III and bismuth(III complexes with the nitrogen-donor heterocyclic ligand dipyrido[3,2-a:2',3'-c]phenazine (dppz were synthesized and characterized as [Sb(dppzCl3]∙H2O∙CH3OH and [Bi(dppzCl3]. The crystal structure of Sb(III complex was determined by X-ray crystallography. These complexes were evaluated for their activity against the promastigote form of Sb(III-sensitive and –resistant Leishmania infantum chagasi and Leishmania amazonensis strains. Both complexes were more effective than dppz alone in inhibiting the growth of Leishmania promastigotes and were at least 77 and 2,400 times more active than potassium antimonyl tartrate in Sb(III-sensitive and -resistant Leishmania, respectively. The cytotoxicity of dppz and its complexes against mouse peritoneal macrophages occurred at dppz concentrations at least 6-fold greater than those found to be active against Leishmania promastigotes.To investigate the role of the metal in the improved antileishmanial activity of dppz, the activity of the Sb(III complex was compared between the Sb-resistant mutants and their respective parental sensitive strains. The lack of cross-resistance to the Sb(III-dppz complex together with the much lower activity of antimonyl tartrate, SbCl3 and BiCl3 strongly support the model that the metal is not active by itself but improves the activity of dppz through complexation.

  10. Sorption of small amounts of europium(III) on iron(III) hydroxide and oxide

    International Nuclear Information System (INIS)

    Music, S.; Gessner, M.; Wolf, R.H.H.

    1979-01-01

    The sorption of small amounts of europium(III) on iron(III) hydroxide and oxide has been studied as a function of pH. The mechanism of sorption is discussed. Optimum conditions have been found for the preconcentration of small or trace amounts of europium(III) by iron(III) hydroxide and oxide. The influence of complexing agents (EDTA, oxalate, tartrate and 5-sulfosalicylic acid) on the sorption of small amounts of europium(III) on iron(III) oxide has also been studied. (author)

  11. Nitrile Hydration by Thiolate–and Alkoxide–Ligated Co-NHase Analogues. Isolation of Co(III)-Amidate and Co(III)–Iminol Intermediates

    Science.gov (United States)

    Swartz, Rodney D.; Coggins, Michael K.; Kaminsky, Werner; Kovacs, Julie A.

    2011-01-01

    Nitrile hydratases (NHases) are thiolate–ligated Fe(III)- or Co(III)-containing enzymes, which convert nitriles to the corresponding amide under mild conditions. Proposed NHase mechanisms involve M(III)–NCR, M(III)–OH, M(III)–iminol and M(III)–amide intermediates. Spectroscopic and kinetic data support the involvement of a M(III)–NCR intermediate. A H–bonding network facilitates this enzymatic reaction. There have been no reported crystallographically characterized examples of these key intermediates. Herein we describe two biomimetic Co(III)–NHase analogues that hydrate MeCN. Four key crystallographically characterized NHase intermediate anaologues, [CoIII(SMe2N4(tren))(MeCN)]2+ (1), [CoIII(SMe2N4(tren))(OH)]+ (3), [CoIII(SMe2N4(tren))(NHC(O)CH3)]+ (2), and [CoIII(OMe2N4(tren))(NHC(OH)CH3)]2+ (5) are described. Iminol–bound 5 represents the first example of a Co(III)-iminol compound in any ligand environment. Kinetic parameters (k1(298 K)= 2.98(5) M−1s−1, ΔH‡ = 12.65(3) kcal/mol, ΔS‡ = −14(7) e.u.) for nitrile hydration by 1 are reported, and the activation energy Ea= 13.2 kcal/mol is compared with that (Ea= 5.5 kcal/mol) of the NHase enzyme. A mechanism involving initial exchange of the bound MeCN for OH− is ruled out by the fact that nitrile exchange from 1 (kex(300 K)= 7.3(1) x10−3 s−1) is two orders of magnitude slower than nitrile hydration, and that hydroxide bound 3 does not promote nitrile hydration. Reactivity of an analogue that incorporates an alkoxide as a mimic of the highly conserved NHase serine residue shows that this moiety facilitates nitrile hydration under milder conditions. Hydrogen-bonding to the alkoxide stabilizes a Co(III)-iminol intermediate. Comparison of the thiolate versus alkoxide intermediate structures shows that C≡N bond activation and C=O bond formation proceed further along the reaction coordinate when a thiolate is incorporated into the coordination sphere. PMID:21351789

  12. Constraining the Statistics of Population III Binaries

    Science.gov (United States)

    Stacy, Athena; Bromm, Volker

    2012-01-01

    We perform a cosmological simulation in order to model the growth and evolution of Population III (Pop III) stellar systems in a range of host minihalo environments. A Pop III multiple system forms in each of the ten minihaloes, and the overall mass function is top-heavy compared to the currently observed initial mass function in the Milky Way. Using a sink particle to represent each growing protostar, we examine the binary characteristics of the multiple systems, resolving orbits on scales as small as 20 AU. We find a binary fraction of approx. 36, with semi-major axes as large as 3000 AU. The distribution of orbital periods is slightly peaked at approx. < 900 yr, while the distribution of mass ratios is relatively flat. Of all sink particles formed within the ten minihaloes, approx. 50 are lost to mergers with larger sinks, and 50 of the remaining sinks are ejected from their star-forming disks. The large binary fraction may have important implications for Pop III evolution and nucleosynthesis, as well as the final fate of the first stars.

  13. The survival of patients with Stage III Colon Cancer is improved in HNPCC compared with sporadic cases. A Danish registry based study

    DEFF Research Database (Denmark)

    Brixen, Line Merrild; Bernstein, Inge Thomsen; Bülow, Steffen

    2013-01-01

    AIM: Patients with hereditary non-polyposis colorectal cancer (HNPCC) seem to have a better prognosis than those with sporadic colon cancer (CC)s. The aim was to compare survival after stage III CC in patients with HNPCC with those having sporadic CC. METHOD: 230 patients with hereditary cancer...... from The Danish HNPCC-Register and 3557 patients with sporadic CC from The Danish Colorectal Cancer Database, diagnosed during May 2001-December 2008 were included. HNPCC patients were classified according to Mismatch Repair mutation status and family pedigree. Sporadic cases had no known family...... history of cancer. Patient characteristics, geographic differences and survival data were analyzed. RESULTS: The overall survival (OS) was better in HNPCC patients compared to sporadic CC after stratification for sex and age (p=0.02; CI 1.04-1.7). The 5-year survival was 70% in HNPCC patients compared...

  14. Diagnostic efficiency of demographically corrected Wechsler Adult Intelligence Scale-III and Wechsler Memory Scale-III indices in moderate to severe traumatic brain injury and lower education levels.

    Science.gov (United States)

    Walker, Alexandra J; Batchelor, Jennifer; Shores, E Arthur; Jones, Mike

    2009-11-01

    Despite the sensitivity of neuropsychological tests to educational level, improved diagnostic accuracy for demographically corrected scores has yet to be established. Diagnostic efficiency statistics of Wechsler Adult Intelligence Scale-III (WAIS-III) and Wechsler Memory Scale-III (WMS-III) indices that were corrected for education, sex, and age (demographically corrected) were compared with age corrected indices in individuals aged 16 to 75 years with moderate to severe traumatic brain injury (TBI) and 12 years or less education. TBI participants (n = 100) were consecutive referrals to an outpatient rehabilitation service and met careful selection criteria. Controls (n = 100) were obtained from the WAIS-III/WMS-III standardization sample. Demographically corrected indices did not provide higher diagnostic efficiency than age corrected indices and this result was supported by reanalysis of the TBI group against a larger and unmatched control group. Processing Speed Index provided comparable diagnostic accuracy to that of combined indices. Demographically corrected indices were associated with higher cut-scores to maximize overall classification, reflecting the upward adjustment of those scores in a lower education sample. This suggests that, in clinical practice, the test results of individuals with limited education may be more accurately interpreted with the application of demographic corrections. Diagnostic efficiency statistics are presented, and future research directions are discussed.

  15. Comparative analysis of the nuclear lens opalescence by the Lens Opacities Classification System III with nuclear density values provided by Oculus Pentacam: a cross-section study using Pentacam Nucleus Staging software

    Directory of Open Access Journals (Sweden)

    Fernanda Pedreira Magalhães

    2011-04-01

    Full Text Available PURPOSE: To compare the clinical classification of cataract using the Lens Opacities Classification System (LOCS III with the mean values of lens density provided by the Pentacam Scheimpflug System in nuclear cataracts. METHODS: One hundred and one eyes from 101 patients with age-related nuclear cataract were submitted to clinical examination for lens grading score using LOCS III. According to LOCS III, nuclear opalescence was divided in six groups. Patients were evaluated by the Pentacam Scheimpflug System for the mean lens density using the Pentacam lens densitometry program (PLDP, the Pentacam Nucleus Staging (PNS mean value and the PNS cataract grading score. RESULTS: A positive correlation between the mean values of lens density and LOCS III classification, considering groups 1 to 5, could be noticed with PLDP and PNS mean value. The mean values between the groups were similar using the PLDP and the PNS mean value. However, when the PNS cataract grading score was evaluated, there was low correspondence with LOCS III classification. CONCLUSION: Pentacam Scheimpflug device offers an objective measure of the lens nuclear density on nuclear cataracts. PLDP and the PNS mean value were both useful to evaluate age-related nuclear cataract up to LOCS III group 5.

  16. Sample exchange/evaluation (SEE) report - Phase III

    International Nuclear Information System (INIS)

    Winters, W.I.

    1996-01-01

    This report describes the results from Phase III of the Sample Exchange Evaluation (SEE) program. The SEE program is used to compare analytical laboratory performance on samples from the Hanford Site's high level waste tanks

  17. Strong and anisotropic superexchange in the single-molecule magnet (SMM) [MnIII(6)OsIII]3+: promoting SMM behavior through 3d-5d transition metal substitution.

    Science.gov (United States)

    Hoeke, Veronika; Stammler, Anja; Bögge, Hartmut; Schnack, Jürgen; Glaser, Thorsten

    2014-01-06

    The reaction of the in situ generated trinuclear triplesalen complex [(talent-Bu2)MnIII3(solv)n]3+ with (Ph4P)3[OsIII(CN)6] and NaClO4·H2O affords [MnIII6OsIII](ClO4)3 (= [{(talent-Bu2)MnIII3}2{OsIII(CN)6}](ClO4)3) in the presence of the oxidizing agent [(tacn)2NiIII](ClO4)3 (tacn =1,4,7-triazacyclononane), while the reaction of [(talent-Bu2)MnIII3(solv)n]3+ with K4[OsII(CN)6] and NaClO4·H2O yields [MnIII6OsII](ClO4)2 under an argon atmosphere. The molecular structure of [MnIII6OsIII]3+ as determined by single-crystal X-ray diffraction is closely related to the already published [MnIII6Mc]3+ complexes (Mc = CrIII, FeIII, CoIII, MnIII). The half-wave potential of the OsIII/OsII couple is E1/2 = 0.07 V vs Fc+/Fc. The FT-IR and electronic absorption spectra of [MnIII6OsII]2+ and [MnIII6OsIII]3+ exhibit distinct features of dicationic and tricationic [MnIII6Mc]n+ complexes, respectively. The dc magnetic data (μeff vs T, M vs B, and VTVH) of [MnIII6OsII]2+ are successfully simulated by a full-matrix diagonalization of a spin-Hamiltonian including isotropic exchange, zero-field splitting with full consideration of the relative orientation of the D-tensors, and Zeeman interaction, indicating antiferromagnetic MnIII–MnIII interactions within the trinuclear triplesalen subunits (JMn–Mn(1) = −(0.53 ± 0.01) cm–1, Ĥex = −2∑iSMM [MnIII6OsIII]3+ compared to the 3d analogue [MnIII6FeIII]3+ due to the stronger and anisotropic Mc–MnIII exchange interaction.

  18. Extracción de cromo con disolventes orgánicos. III parte. Aplicación al tratamiento de residuos polimetálicos industriales

    Directory of Open Access Journals (Sweden)

    de Juan, D.

    1998-10-01

    Full Text Available The use of Primene 81R as extraction agent of chromium present in solid wastes containing nickel, iron and copper has been studied. The waste was leached with a sulphuric acid solution up to pH 3 and oxidation of Cr(III to Cr(VI with Caro acid was also studied. Because of the negative result of oxidation, the treatment was applied on Cr(III directly. Extraction/scrubbing/stripping process was studied in the leach. The composition of organic phase used in the extraction step was 10 % v/v Primene 81R, 10 % isodecanol and kerosene. All the iron, 91 % Cr, 10 % Ni and large part of the copper contained in the initial leach solution are recovered in the organic phase. In the scrubbing stage (with a sulphuric acid solution at pH 1,4, all the copper and nickel and 30 % Cr go to the washing liquor, while all the iron and 70 % Cr remained in the organic phase. In the stripping stage (with a 2N NH4OH or 2N NaOH solution all the iron and chromium are recovered as a precipitate of highly absorbent hydroxides. After the treatment mentioned, 63 % Cr and 100 % Fe are recovered as a mixture of hydroxides, and 28 % of the initial chromium, all the nickel and the copper are found in the washing liquor.

    Se estudia la aplicación del Primene 81R como agente de extracción del cromo presente en residuos sólidos que poseen níquel, hierro y cobre. El residuo se lixivió con disolución de ácido sulfúrico hasta pH 3 y se investigó la oxidación del Cr(III a Cr(VI con ácido de Caro. Ante el nulo resultado en la oxidación, se actuó directamente sobre el Cr(III. Se estudió el proceso de extracción/lavado/reextracción sobre la lejía de lixiviación. La fase orgánica empleada en la extracción estaba constituida por 10 % v/v de Primene 81R, 10 % de isodecanol y queroseno. En la fase orgánica se recupera todo el hierro, el 91 % Cr, el 10 % Ni y gran parte del cobre contenidos en la lejía de partida. En la etapa de lavado (con disolución de

  19. HERBIG-HARO OBJECTS IN THE LUPUS I AND III MOLECULAR CLOUDS

    International Nuclear Information System (INIS)

    Wang Hongchi; Henning, Thomas

    2009-01-01

    We performed a deep search for Herbig-Haro (HH) objects toward the Lupus I and III clouds, covering a sky area of ∼ 1 and ∼ 0.5 deg 2 , respectively. In total, 11 new HH objects, HH 981--991, are discovered. The HH objects both in Lupus I and in Lupus III tend to be concentrated in small areas. The HH objects detected in Lupus I are located in a region of radius 0.26 pc near the young star Sz 68. The abundance of HH objects shows that this region of the cloud is active in on-going star formation. HH objects in the Lup III cloud are concentrated in the central part of the cloud around the Herbig Ae/Be stars HR 5999 and 6000. HH 981 and 982 in Lupus I are probably driven by the young brown dwarf SSTc2d J154457.9-342340 which has a mass of 50 M J . HH 990 and 991 in Lup III align well with the HH 600 jet emanating from the low-mass star Par-Lup3-4, and are probably excited by this low-mass star of spectral type M5. High proper motions for HH 228 W, E, and E2 are measured, which confirms that they are excited by the young star Th 28. In contrast, HH 78 exhibits no measurable proper motion in the time span of 18 years, indicating that HH 78 is unlikely part of the HH 228 flow. The HH objects in Lup I and III are generally weak in terms of brightness and dimension in comparison to HH objects we detected with the same technique in the R CrA and Cha I clouds. Through a comparison with the survey results from the Spitzer c2d program, we find that our optical survey is more sensitive, in terms of detection rate, than the Spitzer IRAC survey to high-velocity outflows in the Lup I and III clouds.

  20. Effectively simultaneous naked-eye detection of Cu(II), Pb(II), Al(III) and Fe(III) using cyanidin extracted from red cabbage as chelating agent

    Science.gov (United States)

    Khaodee, Warangkhana; Aeungmaitrepirom, Wanlapa; Tuntulani, Thawatchai

    Simultaneous determination of Cu(II), Pb(II), Al(III) and Fe(III) using cyanidin as a chelating agent was investigated in terms of both quantitative and qualitative detections. Cyanidin was extracted and purified from red cabbage which is a local plant in Thailand. The selectivity of this method was examined by regulating the pH of cyanidin solution operated together with masking agents. It was found that Cu(II), Pb(II), Al(III) and Fe(III) simultaneously responded with the color change at pH 7, pH 6, pH 5 and pH 4, respectively. KF, DMG and the mixture of KF and DMG were used as masking agents for the determination of Fe(III), Al(III) and Pb(II), respectively. Results from naked-eye detection were evaluated by comparing with those of inductively coupled plasma (ICP), and there was no significant difference noticed. Cyanidin using as a multianalyte reagent could be employed for simultaneous determination of Cu(II), Pb(II), Al(III) and Fe(III) at the lowest concentration at 50, 80, 50 and 200 μM, respectively, by slightly varying pHs. Moreover, the proposed method could be potentially applied for real water samples with simplicity, rapidity, low cost and environmental safety.

  1. Quantum field theory III. Gauge theory. A bridge between mathematicians and physicists

    International Nuclear Information System (INIS)

    Zeidler, Eberhard

    2011-01-01

    In this third volume of his modern introduction to quantum field theory, Eberhard Zeidler examines the mathematical and physical aspects of gauge theory as a principle tool for describing the four fundamental forces which act in the universe: gravitative, electromagnetic, weak interaction and strong interaction. Volume III concentrates on the classical aspects of gauge theory, describing the four fundamental forces by the curvature of appropriate fiber bundles. This must be supplemented by the crucial, but elusive quantization procedure. The book is arranged in four sections, devoted to realizing the universal principle force equals curvature: Part I: The Euclidean Manifold as a Paradigm Part II: Ariadne's Thread in Gauge Theory Part III: Einstein's Theory of Special Relativity Part IV: Ariadne's Thread in Cohomology For students of mathematics the book is designed to demonstrate that detailed knowledge of the physical background helps to reveal interesting interrelationships among diverse mathematical topics. Physics students will be exposed to a fairly advanced mathematics, beyond the level covered in the typical physics curriculum. Quantum Field Theory builds a bridge between mathematicians and physicists, based on challenging questions about the fundamental forces in the universe (macrocosmos), and in the world of elementary particles (microcosmos). (orig.)

  2. Effects upon metabolic pathways and energy production by Sb(III and As(III/Sb(III-oxidase gene aioA in Agrobacterium tumefaciens GW4.

    Directory of Open Access Journals (Sweden)

    Jingxin Li

    Full Text Available Agrobacterium tumefaciens GW4 is a heterotrophic arsenite [As(III]/antimonite [Sb(III]-oxidizing strain. The As(III oxidase AioAB is responsible for As(III oxidation in the periplasm and it is also involved in Sb(III oxidation in Agrobacterium tumefaciens 5A. In addition, Sb(III oxidase AnoA and cellular H2O2 are also responsible for Sb(III oxidation in strain GW4. However, the deletion of aioA increased the Sb(III oxidation efficiency in strain GW4. In the present study, we found that the cell mobility to Sb(III, ATP and NADH contents and heat release were also increased by Sb(III and more significantly in the aioA mutant. Proteomics and transcriptional analyses showed that proteins/genes involved in Sb(III oxidation and resistance, stress responses, carbon metabolism, cell mobility, phosphonate and phosphinate metabolism, and amino acid and nucleotide metabolism were induced by Sb(III and were more significantly induced in the aioA mutant. The results suggested that Sb(III oxidation may produce energy. In addition, without periplasmic AioAB, more Sb(III would enter bacterial cells, however, the cytoplasmic AnoA and the oxidative stress response proteins were significantly up-regulated, which may contribute to the increased Sb(III oxidation efficiency. Moreover, the carbon metabolism was also activated to generate more energy against Sb(III stress. The generated energy may be used in Sb transportation, DNA repair, amino acid synthesis, and cell mobility, and may be released in the form of heat.

  3. Spectroscopic investigations on the complexation of Cm(III) and Eu(III) with organic model ligands and their binding mode in human urine (in vitro)

    International Nuclear Information System (INIS)

    Heller, Anne

    2011-01-01

    In case of incorporation, trivalent actinides (An(III)) and lanthanides (Ln(III)) pose a serious health risk to humans. An(III) are artificial, highly radioactive elements which are mainly produced during the nuclear fuel cycle in nuclear power plants. Via hazardous accidents or nonprofessional storage of radioactive waste, they can be released in the environment and enter the human food chain. In contrast, Ln(III) are nonradioactive, naturally occurring elements with multiple applications in technique and medicine. Consequently it is possible that humans get in contact and incorporate both, An(III) and Ln(III). Therefore, it is of particular importance to elucidate the behaviour of these elements in the human body. While macroscopic processes such as distribution, accumulation and excretion are studied quite well, knowledge about the chemical binding form (speciation) of An(III) and Ln(III) in various body fluids is still sparse. In the present work, for the first time, the speciation of Cm(III) and Eu(III) in natural human urine (in vitro) has been investigated spectroscopically and the formed complex identified. For this purpose, also basic investigations on the complex formation of Cm(III) and Eu(III) in synthetic model urine as well as with the urinary relevant, organic model ligands urea, alanine, phenylalanine, threonine and citrate have been performed and the previously unknown complex stability constants determined. Finally, all experimental results were compared to literature data and predictions calculated by thermodynamic modelling. Since both, Cm(III) and Eu(III), exhibit unique luminescence properties, particularly the suitability of time-resolved laser-induced fluorescence spectroscopy (TRLFS) could be demonstrated as a method to investigate these metal ions in untreated, complex biofluids. The results of this work provide new scientific findings on the biochemical reactions of An(III) and Ln(III) in human body fluids on a molecular scale and

  4. Preparation and chemical studies on Tc(III) complexes containing polyaminocarboxylic acids

    International Nuclear Information System (INIS)

    Gonzalez, R.; Kremer, C.; Chiozzone, R.; Torres, J.; Rivero, M.; Kremer, E.; Leon, A.

    1998-01-01

    Tc(III)-edta (edta = ethylenediaminetetraacetate), Tc(III)-dtpa (dtpa = diethylenetriaminepentaacetate) and Tc(III)-mebrofenin (mebrofenin = 3-bromo-2,4,6-trimethylacetanilideiminodiacetate) complexes were prepared by ligand substitution reactions on hexakis(thiourea)technetium(III) cation with the polycarboxylates. By a combination of different techniques (UV-Vis, IR and 1 H-NMR spectroscopy, Tc elemental analyses and cerimetric titrations) it was concluded that 1:1 complexes are formed with edta and dtpa while mebrofening adopts a 2:1 (ligand to metal) stoichiometry. Complementary, molecular mechanics calculations were performed to analyze the spatial arrangement of the molecules. The stability of the Tc(III) complexes was studied in aqueous solution by paper chromatography, paper electrophoresis and cyclic voltammetry. The chelates are rather stable, in particular when compared with the precursor. (orig.)

  5. 30 CFR 57.22208 - Auxiliary fans (I-A, II-A, III, and V-A mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Auxiliary fans (I-A, II-A, III, and V-A mines... fans (I-A, II-A, III, and V-A mines). (a) Auxiliary fans, except fans used in shops and other areas... applicable requirements of 30 CFR part 18, and be operated so that recirculation is minimized. Auxiliary fans...

  6. Mixed ligand complexes of some of the rare earths. La(III)-, Pr(III)- or Nd-(III)-CDTA-Hydroxy Acids

    Energy Technology Data Exchange (ETDEWEB)

    Rana, H S; Tandon, J P [Rajasthan Univ., Jaipur (India). Chemical Labs.

    1975-11-01

    Biligand complexes of the 1:1 Ln(III)-1,2-diaminocyclohexane-tetraacetic acid (CDTA) chelate with hydroxy acids (where hydroxy acids = salicylic acid (SA); Sulphosalicylic acid (SSA) and 8-hydroxyquinoline-5-sulphonic acid (HQSA)) have been investigated by potentiometric titration. Their formation constants have been calculated (..mu..=0.1M-KNO/sub 3/; and t=30+-1 deg C) as 4.60 +-0.03, 5.46+-0.03, 5.87+-0.05; 3.12+-0.04, 3.95+-0.05, 4.42+-0.07; 2.73+-0.06, 3.45+-0.05 and 3.90+-0.08 for Ln(III)-CDTA-SA,-SSA, and -HQSA respectively (where Ln=La, Pr or Nd). The value of log Ksub(MAB) follows the order: La(III)).

  7. Anteroposterior condylar position: a comparative study between subjects with normal occlusion and patients with Class I, Class II Division 1, and Class III malocclusions.

    Science.gov (United States)

    Fraga, Marcelo Reis; Rodrigues, Andréia Fialho; Ribeiro, Luiz Claudio; Campos, Marcio José da Silva; Vitral, Robert Willer Farinazzo

    2013-10-29

    The present study aimed to determine and compare the anteroposterior position of the condyle in the mandibular fossa between groups of asymptomatic subjects with normal occlusion and asymptomatic subjects with Class I, Class II Division 1, and Class III malocclusions. Thirty persons with normal occlusion, 30 with Class I malocclusion, 30 with Class II Division 1, and 30 with Class III had computed tomography scans of their temporomandibular joints. The anterior joint space/posterior joint space (AJS/PJS) ratio was determined for the right and left joints. The paired t test was used to analyze the AJS/PJS ratio between both sides for each group. The ANOVA test was applied to verify the differences between the groups for the measurements of the right and left sides. In case the ANOVA test confirmed significance, the Dunnett's t test was performed to compare the groups of malocclusion with that of normal occlusion. The paired t test between the AJS/PJS relationships in the right and left sides showed the following p values: Class I (0.168), Class II Division 1 (0.662), Class III (0.991), and normal occlusion (0.390). The ANOVA test showed a p value of 0.445 for the comparisons of the right side and 0.040 for the left side. The Dunnett's t test demonstrated a statistically significant difference between the Class II group and the normal occlusion group (p value of 0.026) in the joints of the left side. Bilateral symmetry and lack of condyle centralization were common characteristics among all groups. The greatest condylar decentralization was observed in the Class II group, whereas the least condylar decentralization was found in the normal occlusion group.

  8. The Effect of early physiotherapy on the recovery of mandibular function after orthognathic surgery for Class III correction: part I--jaw-motion analysis.

    Science.gov (United States)

    Teng, Terry Te-Yi; Ko, Ellen Wen-Ching; Huang, Chiung Shing; Chen, Yu-Ray

    2015-01-01

    The aim of this prospective study was to compare the mandibular range of motion in Class III patients with and without early physiotherapy after orthognathic surgery (OGS). This study consisted of 63 Class III patients who underwent 2-jaw OGS. The experimental group comprised 31 patients who received early systematic physical rehabilitation. The control group consisted of 32 patients who did not have physical rehabilitation. Twelve variables of 3-dimensional (3D) jaw-motion analysis (JMA) were recorded before surgery (T1) and 6 weeks (T2) and 6 months (T3) after surgery. A 2-sample t test was conducted to compare the JMA results between the two groups at different time points. At T2, the JMA data were measured to be 77.5%-145.7% of presurgical values in the experimental group, and 60.3%-90.6% in the control group. At T3, the measurements were 112.2%-179.2% of presurgical values in the experimental group, and 77.6%-157.2% in the control group. The patients in the experimental group exhibited more favorable recovery than did those in the control group, from T1 to T2 and T1 to T3. However, after termination of physiotherapy, no significant difference in the extent of recovery was observed between groups up to 6 months after OGS. Copyright © 2014 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

  9. Comparative studies of praseodymium(III) selective sensors based on newly synthesized Schiff's bases

    International Nuclear Information System (INIS)

    Gupta, Vinod K.; Goyal, Rajendra N.; Pal, Manoj K.; Sharma, Ram A.

    2009-01-01

    Praseodymium ion selective polyvinyl chloride (PVC) membrane sensors, based on two new Schiff's bases 1,3-diphenylpropane-1,3-diylidenebis(azan-1-ylidene)diphenol (M 1 ) and N,N'-bis(pyridoxylideneiminato) ethylene (M 2 ) have been developed and studied. The sensor having membrane composition of PVC: o-NPOE: ionophore (M 1 ): NaTPB (w/w; mg) of 150: 300: 8: 5 showed best performances in comparison to M 2 based membranes. The sensor based on (M 1 ) exhibits the working concentration range 1.0 x 10 -8 to 1.0 x 10 -2 M with a detection limit of 5.0 x 10 -9 M and a Nernstian slope 20.0 ± 0.3 mV decade -1 of activity. It exhibited a quick response time as <8 s and its potential responses were pH independent across the range of 3.5-8.5.The influence of the membrane composition and possible interfering ions have also been investigated on the response properties of the electrode. The sensor has been found to work satisfactorily in partially non-aqueous media up to 15% (v/v) content of methanol, ethanol or acetonitrile and could be used for a period of 3 months. The selectivity coefficients determined by using fixed interference method (FIM) indicate high selectivity for praseodymium(III) ions over wide variety of other cations. To asses its analytical applicability the prepared sensor was successfully applied for determination of praseodymium(III) in spiked water samples.

  10. Transformational III-V Electronics

    KAUST Repository

    Nour, Maha A.

    2014-04-01

    Flexible electronics using III-V materials for nano-electronics with high electron mobility and optoelectronics with direct band gap are attractive for many applications. This thesis describes a complementary metal oxide semiconductor (CMOS) compatible process for transforming traditional III-V materials based electronics into flexible one. The thesis reports releasing 200 nm of Gallium Arsenide (GaAs) from 200 nm GaAs / 300 nm Aluminum Arsenide (AlAs) stack on GaAs substrate using diluted hydrofluoric acid (HF). This process enables releasing a single top layer compared to peeling off all layers with small sizes at the same time. This is done utilizing a network of release holes that contributes to the better transparency (45 % at 724 nm wavelengths) observed. Fabrication of metal oxide semiconductor capacitor (MOSCAPs) on GaAs is followed by releasing it to have devices on flexible 200 nm GaAs. Similarly, flexible GaSb and InP fabrication process is also reported to transform traditional electronics into large-area flexible electronics.

  11. Fate of circulating amino-terminal propeptide of type III procollagen in conscious pigs

    DEFF Research Database (Denmark)

    Jensen, L T; Henriksen, Jens Henrik Sahl; Risteli, J

    1993-01-01

    The amino-terminal propeptide of type III procollagen (PIIINP, M(r) 42,000) is a promising marker for the formation of type III collagen of granulation tissue in experimental and clinical studies. The disposal kinetics of circulating PIIINP is, however, almost unknown. In conscious pigs with a th......The amino-terminal propeptide of type III procollagen (PIIINP, M(r) 42,000) is a promising marker for the formation of type III collagen of granulation tissue in experimental and clinical studies. The disposal kinetics of circulating PIIINP is, however, almost unknown. In conscious pigs...... of the plasma disappearance curve originated from the formation and disappearance of a high and a low molecular weight (MW) fraction as part of the degradation of PIIINP. The high MW fraction (approximately M(r) 90,000) was similar to a previously described, but not further characterized, PIIINP immunoreactive...

  12. Immunohistochemical expression of mitochondrial membrane complexes (MMCs) I, III, IV and V in malignant and benign periampullary epithelium: a potential target for drug therapy of periampullary cancer?

    International Nuclear Information System (INIS)

    Aloysius, Mark M; Zaitoun, Abed M; Bates, Timothy E; Ilyas, Mohammad; Constantin-Teodosiu, Dumitru; Rowlands, Brian J; Lobo, Dileep N

    2010-01-01

    Mitochondrial membrane complexes (MMCs) are key mediators of cellular oxidative phosphorylation, and inhibiting them could lead to cell death. No published data are available on the relative abundance of MMCs in different periampullary cancers. Therefore, we studied the expression profile of MMCs I, III, IV and V in periampullary cancers, reactive pancreatitis, normal pancreas and chronic pancreatitis. This was a retrospective study on tissue microarrays constructed from formalin-fixed paraffin-embedded tissue from 126 consecutive patients (cancer = 104, chronic pancreatitis = 22) undergoing pancreatic resections between June 2001 and June 2006. 78 specimens of chronic pancreatitis tissue were obtained adjacent to areas of cancer. Normal pancreatic tissue was obtained from the resection specimens in a total of 30 patients. Metastatic tumours in 61 regional lymph nodes from 61 patients were also studied. MMCs I, III, IV and V were highly expressed (p < 0.05) in all primary periampullary cancers compared with metastatic lymph nodes and adjacent benign pancreas. MMCs III, IV and V were highly expressed in all cancers regardless of type compared with chronic pancreatitis (p < 0.05). Higher expression of MMCs I and V was associated with better survival and may, in part, relate to lower expression of these MMCs in poorly differentiated tumours compared with well and moderately differentiated tumours. Differential expression of MMCs III, IV and V in primary periampullary cancers compared with adjacent benign periampullary tissue and chronic pancreatitis is a novel finding, which may render them attractive anticancer targets

  13. Enhancement of the fluorescence of the samarium (III) complex by gadolinium (III)

    International Nuclear Information System (INIS)

    Yun-Xiang, C.; Zhang-Hua, L.

    1988-01-01

    The increase in sensitivity and selectivity of reactions in which colored species are formed by the addition of different metal ions is an area of research that has recently been developed. This phenomenon, which is sometimes called cocolaration effect, has been explained by the formation of mixed metal complex. The authors found an analogous phenomenon of reactions forming fluorescent complexes. The complexes of Sm(III)-thenoyltrifluoroacetone (TTA)-phenanthroline (Phen)-Triton-X-100 (TX-100) and Gd(III) (or La(III), Lu(III) and Y(III))-TTA-Phen-TX-100 had practically no fluorescence separately. Instead, a fluorescence-enhancement phenomenon caused by adding Gd or La, Lu and Y ions to the system was observed for the first time. The intensity of the enhanced fluorescence of Sm(III) complex was increased in the following order: La< Y< Lu< Gd. By analogy with cocoloration effect, the authors call this new fluorescence-enhancement phenomenon the co-fluorescence effect. The object of this work was to study the enhancement effect of Gd(III) on the fluorescence of the Sm(III)-TTA-Phen-TX-100 system. The recommended fluorimetric method has been applied to the determination of trace amounts of samarium in ytterbium oxide with satisfactory results. A general reaction mechanism for the system studied was proposed

  14. Valoración psicológica en delitos de violencia de género mediante el Inventario Clínico y Multiaxial de Millon III (MCMI-III

    Directory of Open Access Journals (Sweden)

    Alicia Ballester

    2014-01-01

    Full Text Available Se pretende valorar el estado psicológico de 127 mujeres que denuncian maltrato por parte de su expareja, y de 55 hombres denunciados, a través del MCMI-III, analizando asimismo la influencia de las variables sociodemográficas y del maltrato sobre las puntuaciones del MCMI-III. Las mujeres presentan edad media de 36.25 años (DT = 10.48, y los varones 42.54 años (DT = 12.93. Ambos grupos fueron remitidos al Instituto de Medicina Legal de una provincia española por parte del Juzgado de Violencia sobre la Mujer. Se les administró el MCMI-III, obteniendo perfiles característicos en función de la edad, duración del maltrato y años de convivencia. Las mujeres obtienen puntuaciones altas en deseabilidad social, personalidad compulsiva, ansiedad, distimia, somatomorfo y depresión. Los varones presentan rasgos narcisistas, depresión y dependencia de sustancias. A mayor duración del maltrato aumentan en las mujeres las puntuaciones en personalidad esquizoide, depresiva y autodestructiva, junto a distimia y estrés postraumático, con puntuaciones más bajas en deseabilidad social e histrionismo.

  15. Improved sensitivity for W-band Gd(III)-Gd(III) and nitroxide-nitroxide DEER measurements with shaped pulses

    Science.gov (United States)

    Bahrenberg, Thorsten; Rosenski, Yael; Carmieli, Raanan; Zibzener, Koby; Qi, Mian; Frydman, Veronica; Godt, Adelheid; Goldfarb, Daniella; Feintuch, Akiva

    2017-10-01

    Chirp and shaped pulses have been recently shown to be highly advantageous for improving sensitivity in DEER (double electron-electron resonance, also called PELDOR) measurements due to their large excitation bandwidth. The implementation of such pulses for pulse EPR has become feasible due to the availability of arbitrary waveform generators (AWG) with high sampling rates to support pulse shaping for pulses with tens of nanoseconds duration. Here we present a setup for obtaining chirp pulses on our home-built W-band (95 GHz) spectrometer and demonstrate its performance on Gd(III)-Gd(III) and nitroxide-nitroxide DEER measurements. We carried out an extensive optimization procedure on two model systems, Gd(III)-PyMTA-spacer-Gd(III)-PyMTA (Gd-PyMTA ruler; zero-field splitting parameter (ZFS) D ∼ 1150 MHz) as well as nitroxide-spacer-nitroxide (nitroxide ruler) to evaluate the applicability of shaped pulses to Gd(III) complexes and nitroxides, which are two important classes of spin labels used in modern DEER/EPR experiments. We applied our findings to ubiquitin, doubly labeled with Gd-DOTA-monoamide (D ∼ 550 MHz) as a model for a system with a small ZFS. Our experiments were focused on the questions (i) what are the best conditions for positioning of the detection frequency, (ii) which pump pulse parameters (bandwidth, positioning in the spectrum, length) yield the best signal-to-noise ratio (SNR) improvements when compared to classical DEER, and (iii) how do the sample's spectral parameters influence the experiment. For the nitroxide ruler, we report an improvement of up to 1.9 in total SNR, while for the Gd-PyMTA ruler the improvement was 3.1-3.4 and for Gd-DOTA-monoamide labeled ubiquitin it was a factor of 1.8. Whereas for the Gd-PyMTA ruler the two setups pump on maximum and observe on maximum gave about the same improvement, for Gd-DOTA-monoamide a significant difference was found. In general the choice of the best set of parameters depends on the D

  16. Cobalt (III) complexes as novel matrix metalloproteinase-9 inhibitors

    International Nuclear Information System (INIS)

    Lee, Jiyoun

    2012-01-01

    We have synthesized a series of novel MMP-9 inhibitors containing cobalt(III) complexes. The synthesized cobalt(III) complexes are effective as enzyme inhibitors and the attachment of a biphenyl group enhanced the efficiency of enzyme inhibition up to 6-fold. When compared to the reported non-hydroxamate MMP inhibitors, the synthesized complexes showed comparable in vitro potency. The enzyme assay showed that the cobalt(III) complex can disrupt the zinc binding active site of MMP-9 and is proposed to work via a ligand exchange mechanism. Since histidine residues are essential for the catalytic activity of a large percentage of enzymes and zinc finger proteins, these cobalt(III) complexes can serve as a prototype inhibitor towards various zinc containing enzymes and proteins. Matrix metalloproteinases (MMPs) are a family of zinc binding endopeptidases that play crucial roles in various physiological processes and diseases such as embryogenic growth, angiogenesis, arthritis, skin ulceration, liver fibrosis and tumor metastasis. Because of their implications in a wide range of diseases, MMPs are considered as intriguing drug targets. The majority of MMP inhibitors are organic small molecules containing a hydroxamate functionality for the zinc binding group. This hydroxamate group binds to a zinc(II) center in a bidentate fashion and creates a distorted trigonal bipyramidal geometry

  17. Cobalt (III) complexes as novel matrix metalloproteinase-9 inhibitors

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jiyoun [Sungshin Women' s Univ., Seoul (Korea, Republic of)

    2012-04-15

    We have synthesized a series of novel MMP-9 inhibitors containing cobalt(III) complexes. The synthesized cobalt(III) complexes are effective as enzyme inhibitors and the attachment of a biphenyl group enhanced the efficiency of enzyme inhibition up to 6-fold. When compared to the reported non-hydroxamate MMP inhibitors, the synthesized complexes showed comparable in vitro potency. The enzyme assay showed that the cobalt(III) complex can disrupt the zinc binding active site of MMP-9 and is proposed to work via a ligand exchange mechanism. Since histidine residues are essential for the catalytic activity of a large percentage of enzymes and zinc finger proteins, these cobalt(III) complexes can serve as a prototype inhibitor towards various zinc containing enzymes and proteins. Matrix metalloproteinases (MMPs) are a family of zinc binding endopeptidases that play crucial roles in various physiological processes and diseases such as embryogenic growth, angiogenesis, arthritis, skin ulceration, liver fibrosis and tumor metastasis. Because of their implications in a wide range of diseases, MMPs are considered as intriguing drug targets. The majority of MMP inhibitors are organic small molecules containing a hydroxamate functionality for the zinc binding group. This hydroxamate group binds to a zinc(II) center in a bidentate fashion and creates a distorted trigonal bipyramidal geometry.

  18. VTT ENIGMA Calculations for FUMEX-III CRP

    International Nuclear Information System (INIS)

    Tulkki, Ville

    2013-01-01

    International Atomic Energy Agency IAEA has initiated a string of Coordinated Research Programmes (CRPs) to enhance co-operation between fuel modellers. One of these CRPs, FUMEX-III, was ongoing during 2008 - 2011 and has provided material and incentive for assessment of the fuel codes. This report presents the Finnish FUMEX-III simulations performed with the VTT-modified ENIGMA v5.9b. The work has been done as a part of SAFIR2010 (SAfety of FInnish Reactors 2010) project POKEVA (years 2008 to 2010) and SAFIR2014 project PALAMA (year 2011). VTT Technical Research Centre of Finland received ENIGMA v5.9b from Nuclear Electric plc of the UK in 1992. Internal development has been on-going since then. 'ENIGMA v5.9b with VTT modifications' (from now on, 'ENIGMA' for short) is a separate and different program from British Energy's ENIGMA 5.14 and UK National Nuclear Laboratory's ENIGMA-B. The FUMEX-III work has been performed in tandem of VTT's internal review work attempting to catalogue the changes done since 1992 and to assess the current state of the code. Several individual internal reports detail the changes made and the individual model assessments done during the years. (author)

  19. As(III) oxidation by MnO2 during groundwater treatment.

    Science.gov (United States)

    Gude, J C J; Rietveld, L C; van Halem, D

    2017-03-15

    The top layer of natural rapid sand filtration was found to effectively oxidise arsenite (As(III)) in groundwater treatment. However, the oxidation pathway has not yet been identified. The aim of this study was to investigate whether naturally formed manganese oxide (MnO 2 ), present on filter grains, could abiotically be responsible for As(III) oxidation in the top of a rapid sand filter. For this purpose As(III) oxidation with two MnO 2 containing powders was investigated in aerobic water containing manganese(II) (Mn(II)), iron(II) (Fe(II)) and/or iron(III) (Fe(III)). The first MnO 2 powder was a very pure - commercially available - natural MnO 2 powder. The second originated from a filter sand coating, produced over 22 years in a rapid filter during aeration and filtration. Jar test experiments showed that both powders oxidised As(III). However, when applying the MnO 2 in aerated, raw groundwater, As(III) removal was not enhanced compared to aeration alone. It was found that the presence of Fe(II)) and Mn(II) inhibited As(III) oxidation, as Fe(II) and Mn(II) adsorption and oxidation were preferred over As(III) on the MnO 2 surface (at pH 7). Therefore it is concluded that just because MnO 2 is present in a filter bed, it does not necessarily mean that MnO 2 will be available to oxidise As(III). However, unlike Fe(II), the addition of Fe(III) did not hinder As(III) oxidation on the MnO 2 surface; resulting in subsequent effective As(V) removal by the flocculating hydrous ferric oxides. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Metallothionein (MT)-III

    DEFF Research Database (Denmark)

    Carrasco, J; Giralt, M; Molinero, A

    1999-01-01

    Metallothionein-III is a low molecular weight, heavy-metal binding protein expressed mainly in the central nervous system. First identified as a growth inhibitory factor (GIF) of rat cortical neurons in vitro, it has subsequently been shown to be a member of the metallothionein (MT) gene family...... injected rats. The specificity of the antibody was also demonstrated in immunocytochemical studies by the elimination of the immunostaining by preincubation of the antibody with brain (but not liver) extracts, and by the results obtained in MT-III null mice. The antibody was used to characterize...... the putative differences between the rat brain MT isoforms, namely MT-I+II and MT-III, in the freeze lesion model of brain damage, and for developing an ELISA for MT-III suitable for brain samples. In the normal rat brain, MT-III was mostly present primarily in astrocytes. However, lectin staining indicated...

  1. A radiographic study of temporomandibular joints in skeletal class III malocclusion

    International Nuclear Information System (INIS)

    Kim, Sung Eun; Kim, Kae Duk

    2003-01-01

    To investigate the differences between the position of the mandibular condyles in temporomandibular joints of patients presenting with normal occlusion and skeletal class III malocclusion. Forty-two subjects with normal occlusion and thirty-seven subjects exhibiting skeletal class III malocclusion prior to orthodontic treatment were included in the study. Transcranial radiographs of each subject were taken at centric occlusion and 1 inch mouth opening. The positional relationship between the mandibular condyles with articular fossae and articular eminences at two positional states were evaluated and analyzed statistically. The mandibular condyles of the skeletal class III malocclusion group were found to be located more anteriorly from the center of the articular fossae compared to the normal occlusion group in centric occlusion. The mandibular condyles of the skeletal Class III malocclusion group were located more superiorly from the middle of articular height than those of the normal occlusion group in centric occlusion. However, these differences were not statistically significant. At 1 inch mouth opening, the mandibular condyles of the skeletal class III malocclusion group were placed more posteriorly from the articular eminences than those of the normal occlusion group. The mean angle of the articular eminence posterior slope were 56.51 .deg. ± 6.29 .deg. in the normal occlusion group and 60.37 .deg. ± 6.26 .deg. in the skeletal Class III malocclusion group. The mandibular condyles of the skeletal Class III malocclusion group were placed more anteriorly at centric occlusion and more posteriorly at 1 inch mouth opening when compared with those of the normal occlusion group.

  2. A radiographic study of temporomandibular joints in skeletal class III malocclusion

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sung Eun; Kim, Kae Duk [Chosun University College of Medicine, Kwangju (Korea, Republic of)

    2003-06-15

    To investigate the differences between the position of the mandibular condyles in temporomandibular joints of patients presenting with normal occlusion and skeletal class III malocclusion. Forty-two subjects with normal occlusion and thirty-seven subjects exhibiting skeletal class III malocclusion prior to orthodontic treatment were included in the study. Transcranial radiographs of each subject were taken at centric occlusion and 1 inch mouth opening. The positional relationship between the mandibular condyles with articular fossae and articular eminences at two positional states were evaluated and analyzed statistically. The mandibular condyles of the skeletal class III malocclusion group were found to be located more anteriorly from the center of the articular fossae compared to the normal occlusion group in centric occlusion. The mandibular condyles of the skeletal Class III malocclusion group were located more superiorly from the middle of articular height than those of the normal occlusion group in centric occlusion. However, these differences were not statistically significant. At 1 inch mouth opening, the mandibular condyles of the skeletal class III malocclusion group were placed more posteriorly from the articular eminences than those of the normal occlusion group. The mean angle of the articular eminence posterior slope were 56.51 .deg. {+-} 6.29 .deg. in the normal occlusion group and 60.37 .deg. {+-} 6.26 .deg. in the skeletal Class III malocclusion group. The mandibular condyles of the skeletal Class III malocclusion group were placed more anteriorly at centric occlusion and more posteriorly at 1 inch mouth opening when compared with those of the normal occlusion group.

  3. The content and ratio of type I and III collagen in skin differ with age ...

    African Journals Online (AJOL)

    III ratio and changes in skin tension, elasticity, and healing. Also, the content of type I, III collagen and type I/III ratio are significantly altered in hypertrophic scar tissue compared to uninjured age-matched controls, resulting in a different structural ...

  4. The essential function of B. subtilis RNase III is to silence foreign toxin genes.

    Directory of Open Access Journals (Sweden)

    Sylvain Durand

    Full Text Available RNase III-related enzymes play key roles in cleaving double-stranded RNA in many biological systems. Among the best-known are RNase III itself, involved in ribosomal RNA maturation and mRNA turnover in bacteria, and Drosha and Dicer, which play critical roles in the production of micro (mi-RNAs and small interfering (si-RNAs in eukaryotes. Although RNase III has important cellular functions in bacteria, its gene is generally not essential, with the remarkable exception of that of Bacillus subtilis. Here we show that the essential role of RNase III in this organism is to protect it from the expression of toxin genes borne by two prophages, Skin and SPβ, through antisense RNA. Thus, while a growing number of organisms that use RNase III or its homologs as part of a viral defense mechanism, B. subtilis requires RNase III for viral accommodation to the point where the presence of the enzyme is essential for cell survival. We identify txpA and yonT as the two toxin-encoding mRNAs of Skin and SPβ that are sensitive to RNase III. We further explore the mechanism of RNase III-mediated decay of the txpA mRNA when paired to its antisense RNA RatA, both in vivo and in vitro.

  5. Wind waves modelling on the water body with coupled WRF and WAVEWATCH III models

    Science.gov (United States)

    Kuznetsova, Alexandra; Troitskaya, Yuliya; Kandaurov, Alexander; Baydakov, Georgy; Vdovin, Maxim; Papko, Vladislav; Sergeev, Daniil

    2015-04-01

    Simulation of ocean and sea waves is an accepted instrument for the improvement of the weather forecasts. Wave modelling, coupled models modelling is applied to open seas [1] and is less developed for moderate and small inland water reservoirs and lakes, though being of considerable interest for inland navigation. Our goal is to tune the WAVEWATCH III model to the conditions of the inland reservoir and to carry out the simulations of surface wind waves with coupled WRF (Weather Research and Forecasting) and WAVEWATCH III models. Gorky Reservoir, an artificial lake in the central part of the Volga River formed by a hydroelectric dam, was considered as an example of inland reservoir. Comparing to [2] where moderate constant winds (u10 is up to 9 m/s) of different directions blowing steadily all over the surface of the reservoir were considered, here we apply atmospheric model WRF to get wind input to WAVEWATCH III. WRF computations were held on the Yellowstone supercomputer for 4 nested domains with minimum scale of 1 km. WAVEWATCH III model was tuned for the conditions of the Gorky Reservoir. Satellite topographic data on altitudes ranged from 56,6° N to 57,5° N and from 42.9° E to 43.5° E with increments 0,00833 ° in both directions was used. 31 frequencies ranged from 0,2 Hz to 4 Hz and 30 directions were considered. The minimal significant wave height was changed to the lower one. The waves in the model were developing from some initial seeding spectral distribution (Gaussian in frequency and space, cosine in direction). The range of the observed significant wave height in the numerical experiment was from less than 1 cm up to 30 cm. The field experiments were carried out in the south part of the Gorky reservoir from the boat [2, 3]. 1-D spectra of the field experiment were compared with those obtained in the numerical experiments with different parameterizations of flux provided in WAVEWATCH III both with constant wind input and WRF wind input. For all the

  6. Sorption behavior of europium(III) and curium(III) on the cell surfaces of microorganisms

    International Nuclear Information System (INIS)

    Ozaki, T.; Kimura, T.; Ohnuki, T.; Yoshida, Z.; Gillow, J.B.; Francis, A.J.

    2004-01-01

    We investigated the association of europium(III) and curium(III) with the microorganisms Chlorella vulgaris, Bacillus subtilis, Pseudomonas fluorescens, Halomonas sp., Halobacterium salinarum, and Halobacterium halobium. We determined the kinetics and distribution coefficients (K d ) for Eu(III) and Cm(III) sorption at pH 3-5 by batch experiments, and evaluated the number of water molecules in the inner-sphere (N H 2 O ) and the degree of strength of ligand field (R E/M ) for Eu(III) by time-resolved laser-induced fluorescence spectroscopy (TRLFS). Exudates from C. vulgaris, Halomonas sp., and H. halobium had an affinity for Eu(III) and Cm(III). The log K d of Eu(III) and Cm(III) showed that their sorption was not fully due to the exchange with three protons on the functional groups on cell surfaces. The halophilic microorganisms (Halomonas sp., Halobacterium salinarum, H. halobium) showed almost no pH dependence in log K d , indicating that an exchange with Na + on the functional groups was involved in their sorption. The ΔN H 2 O (= 9 - N H 2 O ) for Eu(III) on C. vulgaris was 1-3, while that for the other microorganisms was over 3, demonstrating that the coordination of Eu(III) with C. vulgaris was predominantly an outer-spherical process. The R E/M for Eu(III) on halophilic microorganisms was 2.5-5, while that for non-halophilic ones was 1-2.5. This finding suggests that the coordination environment of Eu(III) on the halophilic microorganisms is more complicated than that on the other three non-halophilic ones. (orig.)

  7. Sorption behavior of europium(III) and curium(III) on the cell surfaces of microorganisms

    Energy Technology Data Exchange (ETDEWEB)

    Ozaki, T.; Kimura, T.; Ohnuki, T.; Yoshida, Z. [Advanced Science Research Center, Japan Atomic Energy Research Inst., Ibaraki (Japan); Gillow, J.B.; Francis, A.J. [Environmental Sciences Dept., Brookhaven National Lab., Upton, NY (United States)

    2004-07-01

    We investigated the association of europium(III) and curium(III) with the microorganisms Chlorella vulgaris, Bacillus subtilis, Pseudomonas fluorescens, Halomonas sp., Halobacterium salinarum, and Halobacterium halobium. We determined the kinetics and distribution coefficients (K{sub d}) for Eu(III) and Cm(III) sorption at pH 3-5 by batch experiments, and evaluated the number of water molecules in the inner-sphere (N{sub H{sub 2}O}) and the degree of strength of ligand field (R{sub E/M}) for Eu(III) by time-resolved laser-induced fluorescence spectroscopy (TRLFS). Exudates from C. vulgaris, Halomonas sp., and H. halobium had an affinity for Eu(III) and Cm(III). The log K{sub d} of Eu(III) and Cm(III) showed that their sorption was not fully due to the exchange with three protons on the functional groups on cell surfaces. The halophilic microorganisms (Halomonas sp., Halobacterium salinarum, H. halobium) showed almost no pH dependence in log K{sub d}, indicating that an exchange with Na{sup +} on the functional groups was involved in their sorption. The {delta}N{sub H{sub 2}O} (= 9 - N{sub H{sub 2}O}) for Eu(III) on C. vulgaris was 1-3, while that for the other microorganisms was over 3, demonstrating that the coordination of Eu(III) with C. vulgaris was predominantly an outer-spherical process. The R{sub E/M} for Eu(III) on halophilic microorganisms was 2.5-5, while that for non-halophilic ones was 1-2.5. This finding suggests that the coordination environment of Eu(III) on the halophilic microorganisms is more complicated than that on the other three non-halophilic ones. (orig.)

  8. Drivers of costs associated with reperfusion therapy in acute stroke: the Interventional Management of Stroke III Trial.

    Science.gov (United States)

    Simpson, Kit N; Simpson, Annie N; Mauldin, Patrick D; Hill, Michael D; Yeatts, Sharon D; Spilker, Judith A; Foster, Lydia D; Khatri, Pooja; Martin, Renee; Jauch, Edward C; Kleindorfer, Dawn; Palesch, Yuko Y; Broderick, Joseph P

    2014-06-01

    The Interventional Management of Stroke (IMS) III study tested the effect of intravenous tissue-type plasminogen activator (tPA) alone when compared with intravenous tPA followed by endovascular therapy and collected cost data to assess the economic implications of the 2 therapies. This report describes the factors affecting the costs of the initial hospitalization for acute stroke subjects from the United States. Prospective cost analysis of the US subjects was treated with intravenous tPA alone or with intravenous tPA followed by endovascular therapy in the IMS III trial. Results were compared with expected Medicare payments. The adjusted cost of a stroke admission in the study was $35 130 for subjects treated with endovascular therapy after intravenous tPA treatment and $25 630 for subjects treated with intravenous tPA alone (P<0.0001). Significant factors related to costs included treatment group, baseline National Institutes of Health Stroke Scale, time from stroke onset to intravenous tPA, age, stroke location, and comorbid diabetes mellitus. The mean cost for subjects who had routine use of general anesthesia as part of endovascular therapy was $46 444 when compared with $30 350 for those who did not have general anesthesia. The costs of embolectomy for IMS III subjects and patients from the National Inpatient Sample cohort exceeded the Medicare diagnosis-related group payment in ≥75% of patients. Minimizing the time to start of intravenous tPA and decreasing the use of routine general anesthesia may improve the cost-effectiveness of medical and endovascular therapy for acute stroke. http://www.clinicaltrials.gov. Unique identifier: NCT00359424. © 2014 American Heart Association, Inc.

  9. Synthesis and photophysical properties of indium(III) phthalocyanine derivatives

    Energy Technology Data Exchange (ETDEWEB)

    Özceşmeci, İbrahim, E-mail: ozcesmecii@itu.edu.tr [Department of Chemistry, Technical University of Istanbul, Maslak 34469, Istanbul (Turkey); Gelir, Ali [Department of Physics, Technical University of Istanbul, Maslak 34469, Istanbul (Turkey); Gül, Ahmet [Department of Chemistry, Technical University of Istanbul, Maslak 34469, Istanbul (Turkey)

    2014-03-15

    Three chloroindium(III) phthalocyanine derivatives bearing four aromatic (naphthalene or pyrene) or aliphatic (hexylthio) groups were prepared from corresponding phthalonitrile compounds. The indium(III) phthalocyanine derivatives were characterized with elemental analyses, mass, proton nuclear magnetic resonance ({sup 1}H NMR), Fourier transform infrared spectroscopy (FT-IR) and ultraviolet–visible spectroscopy (UV–vis) techniques. Quantum yields and the energy transfer from the substituents to phthalocyanine core were examined. No energy transfer was observed for 5. The energy transfer efficiency from pyrene units to indium phthalocyanine core was calculated as 0.27 for 6. Quantum yields of all samples were very small due to heavy atom effect of indium atom in the core. It was also observed that upon binding of pyrene and naphthalene units to indium phthalocyanine as substituents, the quantum yields of indium phthalocyanine parts of 5 and 6 decreased. -- Highlights: • Three chloroindium(III) phthalocyanines were prepared and characterized. • Aggregation properties of these compounds were investigated. • The energy transfer efficiency was examined. • Quantum yield of these systems were calculated.

  10. Comparison of collagen fibre architecture between slow-twitch cranial and fast-twitch caudal parts of broiler M. latissimus dorsi.

    Science.gov (United States)

    Nakamura, Y N; Iwamoto, H; Tabata, S; Ono, Y

    2003-07-01

    1. Collagen fibre architectures of perimysium and endomysium in the slow-twitch cranial and fast-twitch caudal parts of broiler M. latissimus dorsi were compared. 2. Type I and III collagens were distributed in both perimysium and endomysium as indicated by their positive immunohistochemical reactions to polyclonal antibodies. 3. Cells invested by endomysium with no myofibres were larger in the cranial part because of the presence of larger slow-twitch myofibres. The honeycomb structure of endomysium was divided into several parts by thick perimysium. 4. The thick perimysial collagen fibres with parallel fibrils, which were interconnected by the loose reticular fibrils and thin fibres, were more numerous and thicker in the cranial part than the caudal. 5. Thick endomysial sidewall of cells in the cranial part was composed of a rougher reticulum of slightly thicker collagen fibrils compared with the thin sidewall in the caudal part. 6. These results indicated that both perimysial constitutions of collagen fibres and endomysial collagen fibrils had attained much larger growth in the slow-twitch cranial part than the fast-twitch caudal in broiler latissimus dorsi muscle.

  11. Conversion between Addenbrooke's Cognitive Examination III and Mini-Mental State Examination.

    Science.gov (United States)

    Matías-Guiu, Jordi A; Pytel, Vanesa; Cortés-Martínez, Ana; Valles-Salgado, María; Rognoni, Teresa; Moreno-Ramos, Teresa; Matías-Guiu, Jorge

    2017-12-10

    We aim to provide a conversion between Addenbrooke's Cognitive Examination III (ACE-III) and Mini-Mental State Examination (MMSE) scores, to predict the MMSE result based on ACE-III, thus avoiding the need for both tests, and improving their comparability. Equipercentile equating method was used to elaborate a conversion table using a group of 400 participants comprising healthy controls and Alzheimer's disease (AD) patients. Then, reliability was assessed in a group of 100 healthy controls and patients with AD, 52 with primary progressive aphasia and 22 with behavioral variant frontotemporal dementia. The conversion table between ACE-III and MMSE denoted a high reliability, with intra-class correlation coefficients of 0.940, 0.922, and 0.902 in the groups of healthy controls and AD, behavioral variant frontotemporal dementia, and primary progressive aphasia, respectively. Our conversion table between ACE-III and MMSE suggests that MMSE may be estimated based on the ACE-III score, which could be useful for clinical and research purposes.

  12. Summary of design of nuclear vessels and piping to ASME III (NB, NC, ND) and vessels to BS 5500

    International Nuclear Information System (INIS)

    Harrop, L.P.

    1992-01-01

    There is a hierarchy of design code requirements for pressurised components, starting with non-nuclear codes as the minimum and progressing through the ASME III nuclear Classes 3, 2, 1. In establishing and assessing the safety justifications of nuclear plants it is important to have an appreciation of the gradation of requirements in the ASME III design rules and how these go beyond non-nuclear component design rules. There are two broad aspects to the structural integrity of pressurised components, namely the achievement of integrity and the demonstration of integrity. The technical requirements of design codes are associated with achieving integrity while the documentary aspects are usually associated with demonstrating integrity. In practice documents also have a part in achieving integrity in the communication of information between different organisations and personnel involved in the design process. It is not possible to assign simple numerical measures to the relative integrity afforded by non-nuclear codes and the three Classes of ASME III. Instead it is necessary to compare the different requirements of the rules for the various technical and documentary aspects. This paper summarises the most important technical and documentary aspects of the three Classes of the ASME III Code for vessels and the non-nuclear code BS 5500. A similar summary is also provided for the three Classes of ASME III rules for piping. The intention is that the paper provides a basis for appreciating the relative integrity afforded by these various rules. (author)

  13. A Main Steam Safety Valve (MSSV) With Fixed Blowdown According to ASME Section III,Part NC-7512

    International Nuclear Information System (INIS)

    Follmer, Bernhard; Schnettler, Armin

    2002-01-01

    In 1986, the NRC issued the Information Notice (IN) 86-05 'Main Steam Safety Valve test failures and ring setting adjustments'. Shortly after this IN was issued, the Code was revised to require that a full flow test has to be performed on each CL.2 MSSV by the manufacturer to verify that the valve was adjusted so that it would reach full lift and thus full relieving capacity and would re-close at a pressure as specified in the valve Design Specification. In response to the concern discussed in the IN, the Westinghouse Owners Group (WOG) performed extensive full flow testing on PWR MSSVs and found that each valve required a unique setting of a combination of two rings in order to achieve full lift at accumulation of 3% and re-closing at a blowdown of 5%. The Bopp and Reuther MSSV type SiZ 2507 has a 'fixed blowdown' i.e. without any adjusting rings to adjust the 'blowdown' so that the blowdown is 'fixed'. More than 1000 pieces of this type are successfully in nuclear power plants in operation. Many of them since about 25 years. Therefore it can be considered as a proven design. It is new that an optimization of this MSSV type SiZ 2507 fulfill the requirements of part NC-7512 of the ASME Section III although there are still no adjusting rings in the flow part. In 2000, for the Qinshan Candu unit 1 and 2 full flow tests were performed with 32 MSSV type SiZ 2507 size 8'' x 12'' at 51 bar saturated steam in only 6 days. In all tests the functional performance was very stable. It was demonstrated by recording the signals lift and system pressure that all valves had acceptable results to achieve full lift at accumulation of 3% and to re-close at blowdown of 5%. This is an advantage which gives a reduction in cost for flow tests and which gives more reliability after maintenance work during outage compared to the common MSSV design with an individual required setting of the combination of the two rings. The design of the type SiZ 2507 without any adjusting rings in the

  14. CHAOS. III. GAS-PHASE ABUNDANCES IN NGC 5457

    Energy Technology Data Exchange (ETDEWEB)

    Croxall, Kevin V.; Pogge, Richard W. [Department of Astronomy, The Ohio State University, 140 West 18th Avenue, Columbus, OH 43210 (United States); Berg, Danielle A. [Center for Gravitation, Cosmology and Astrophysics, Department of Physics, University of Wisconsin Milwaukee, 1900 East Kenwood Boulevard, Milwaukee, WI 53211 (United States); Skillman, Evan D. [Minnesota Institute for Astrophysics, University of Minnesota, 116 Church Street SE, Minneapolis, MN 55455 (United States); Moustakas, John [Department of Physics and Astronomy, Siena College, 515 Loudon Road, Loudonville, NY 12211 (United States)

    2016-10-10

    We present Large Binocular Telescope observations of 109 H ii regions in NGC 5457 (M101) obtained with the Multi-Object Double Spectrograph. We have robust measurements of one or more temperature-sensitive auroral emission lines for 74 H ii regions, permitting the measurement of “direct” gas-phase abundances. Comparing the temperatures derived from the different ionic species, we find: (1) strong correlations of T [N ii] with T [S iii] and T [O iii], consistent with little or no intrinsic scatter; (2) a correlation of T [S iii] with T [O iii], but with significant intrinsic dispersion; (3) overall agreement between T [N ii], T [S ii], and T [O ii], as expected, but with significant outliers; (4) the correlations of T [N ii] with T [S iii] and T [O iii] match the predictions of photoionization modeling while the correlation of T [S iii] with T [O iii] is offset from the prediction of photoionization modeling. Based on these observations, which include significantly more observations of lower excitation H ii regions, missing in many analyses, we inspect the commonly used ionization correction factors (ICFs) for unobserved ionic species and propose new empirical ICFs for S and Ar. We have discovered an unexpected population of H ii regions with a significant offset to low values in Ne/O, which defies explanation. We derive radial gradients in O/H and N/O which agree with previous studies. Our large observational database allows us to examine the dispersion in abundances, and we find intrinsic dispersions of 0.074 ± 0.009 in O/H and 0.095 ± 0.009 in N/O (at a given radius). We stress that this measurement of the intrinsic dispersion comes exclusively from direct abundance measurements of H ii regions in NGC 5457.

  15. A simple, fast, and accurate thermodynamic-based approach for transfer and prediction of gas chromatography retention times between columns and instruments Part III: Retention time prediction on target column.

    Science.gov (United States)

    Hou, Siyuan; Stevenson, Keisean A J M; Harynuk, James J

    2018-03-27

    This is the third part of a three-part series of papers. In Part I, we presented a method for determining the actual effective geometry of a reference column as well as the thermodynamic-based parameters of a set of probe compounds in an in-house mixture. Part II introduced an approach for estimating the actual effective geometry of a target column by collecting retention data of the same mixture of probe compounds on the target column and using their thermodynamic parameters, acquired on the reference column, as a bridge between both systems. Part III, presented here, demonstrates the retention time transfer and prediction from the reference column to the target column using experimental data for a separate mixture of compounds. To predict the retention time of a new compound, we first estimate its thermodynamic-based parameters on the reference column (using geometric parameters determined previously). The compound's retention time on a second column (of previously determined geometry) is then predicted. The models and the associated optimization algorithms were tested using simulated and experimental data. The accuracy of predicted retention times shows that the proposed approach is simple, fast, and accurate for retention time transfer and prediction between gas chromatography columns. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. National Energy Board 1992-93 estimates part III expenditure plan

    International Nuclear Information System (INIS)

    1992-01-01

    This Expenditure Plan is designed to be used as a reference document. As such, it contains several levels of detail to respond to the various needs of its audience. This Plan is divided into two sections. Section 1 presents an overview of the Program including a description, information on its background, objectives and planning perspective as well as performance information that forms the basis for the resources requested. Section 2 provides further information on costs and resources as well as special analyses that the reader may require to understand the Program more fully. Section 1 is preceded by details of Spending Authorities from Part 2 of the Estimates and Volume 2 of the Public Accounts. This is to provide continuity with other Estimates documents and to help in assessing the Program's financial performance over the past year. The format and organization of the document should be regarded as transitional. For the most part the document is organized to be consistent with the program structure approved for the National Energy Board. 16 figs

  17. National Energy Board 1992-93 estimates part III expenditure plan

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-31

    This Expenditure Plan is designed to be used as a reference document. As such, it contains several levels of detail to respond to the various needs of its audience. This Plan is divided into two sections. Section 1 presents an overview of the Program including a description, information on its background, objectives and planning perspective as well as performance information that forms the basis for the resources requested. Section 2 provides further information on costs and resources as well as special analyses that the reader may require to understand the Program more fully. Section 1 is preceded by details of Spending Authorities from Part 2 of the Estimates and Volume 2 of the Public Accounts. This is to provide continuity with other Estimates documents and to help in assessing the Program`s financial performance over the past year. The format and organization of the document should be regarded as transitional. For the most part the document is organized to be consistent with the program structure approved for the National Energy Board. 16 figs.

  18. A comparative study on antioxidant activity of different parts of lotus (Nelumbo nuficera Gaertn rhizome

    Directory of Open Access Journals (Sweden)

    Dongmei YANG

    Full Text Available Abstract In this study, the antioxidant activities of different parts of lotus (Nelumbo nuficera Gaertn rhizome were compared. The total phenolic content of lotus rhizome was determined, and Ferric reducing antioxidant power (FRAP assay, 1,1-diphenyl-2-picrylhydrazyl hydrate (DPPH radical-scavenging assay and β-carotene-linoleic acid assay were performed to assess the antioxidant activity of lotus rhizome. Results showed that there was a significant difference in total phenolic content and antioxidant activity between any two of four parts of lotus rhizome. The order of total phenolic content and antioxidant activity in different parts of lotus rhizome was as follows: peel of old lotus rhizome > peel of young lotus rhizome > flesh of old lotus rhizome > flesh of young lotus rhizome. The total phenol content is significantly positive correlated with the antioxidant activity in different parts of lotus rhizome. This study has provided a basis for further exploring the antioxidant components in lotus rhizome.

  19. Transuranium perrhenates: Np(IV), Pu(IV) and (III), Am (III)

    International Nuclear Information System (INIS)

    Silvestre, Jean-Paul; Freundlich, William; Pages, Monique

    1977-01-01

    Synthesis in aqueous solution and by solid state reactions, crystallographical characterization and study of the stability of some transuranium perrhenates: Asup(n+)(ReO 4 - )sub(n) (A=Np(IV), Pu(IV), Pu(III), Am(III) [fr

  20. Parametric Sensitivity Analysis of the WAVEWATCH III Model

    Directory of Open Access Journals (Sweden)

    Beng-Chun Lee

    2009-01-01

    Full Text Available The parameters in numerical wave models need to be calibrated be fore a model can be applied to a specific region. In this study, we selected the 8 most important parameters from the source term of the WAVEWATCH III model and subjected them to sensitivity analysis to evaluate the sensitivity of the WAVEWATCH III model to the selected parameters to determine how many of these parameters should be considered for further discussion, and to justify the significance priority of each parameter. After ranking each parameter by sensitivity and assessing their cumulative impact, we adopted the ARS method to search for the optimal values of those parameters to which the WAVEWATCH III model is most sensitive by comparing modeling results with ob served data at two data buoys off the coast of north eastern Taiwan; the goal being to find optimal parameter values for improved modeling of wave development. The procedure adopting optimal parameters in wave simulations did improve the accuracy of the WAVEWATCH III model in comparison to default runs based on field observations at two buoys.

  1. Exposure of [Mn{sup III}{sub 6}Cr{sup III}]{sup 3+} single-molecule magnets to soft X-rays: The effect of the counterions on radiation stability

    Energy Technology Data Exchange (ETDEWEB)

    Helmstedt, Andreas, E-mail: andreas.helmstedt@uni-bielefeld.de [Fakultaet fuer Physik, Universitaet Bielefeld, Universitaetsstrasse 25, D-33615 Bielefeld (Germany); Sacher, Marc D.; Gryzia, Aaron; Harder, Alexander; Brechling, Armin; Mueller, Norbert; Heinzmann, Ulrich [Fakultaet fuer Physik, Universitaet Bielefeld, Universitaetsstrasse 25, D-33615 Bielefeld (Germany); Hoeke, Veronika; Krickemeyer, Erich; Glaser, Thorsten [Fakultaet fuer Chemie, Universitaet Bielefeld, Universitaetsstrasse 25, D-33615 Bielefeld (Germany); Bouvron, Samuel; Fonin, Mikhail [Fachbereich Physik, Universitaet Konstanz, Universitaetsstrasse 10, D-78457 Konstanz (Germany)

    2012-01-15

    Highlights: Black-Right-Pointing-Pointer [Mn{sup III}{sub 6}Cr{sup III}]{sup 3+} single-molecule magnets adsorbed on gold are investigated. Black-Right-Pointing-Pointer The oxidation state of the Mn{sup III} constituents changes under X-ray exposure. Black-Right-Pointing-Pointer The change is monitored by Mn-L{sub 3}-edge XAS. Black-Right-Pointing-Pointer Choice of anions strongly influences radiation stability of the SMM. Black-Right-Pointing-Pointer No influence of the sample morphology on radiation stability could be observed. - Abstract: X-ray absorption spectroscopy studies of the [Mn{sup III}{sub 6}Cr{sup III}]{sup 3+} single-molecule magnet deposited as a microcrystalline layer on gold substrates are presented. The oxidation state of the manganese centers changes from Mn{sup III} to Mn{sup II} due to irradiation with soft X-rays. The influence of the charge-neutralizing anions on the stability of [Mn{sup III}{sub 6}Cr{sup III}]{sup 3+} against soft X-ray exposure is investigated for the different anions tetraphenylborate (BPh{sub 4}{sup -}), lactate (C{sub 3}H{sub 5}O{sub 3}{sup -}) and perchlorate (ClO{sub 4}{sup -}). The exposure dependence of the radiation-induced reduction process is compared for [Mn{sup III}{sub 6}Cr{sup III}]{sup 3+} with the three different anions.

  2. Quantum field theory III. Gauge theory. A bridge between mathematicians and physicists

    Energy Technology Data Exchange (ETDEWEB)

    Zeidler, Eberhard [Max Planck Institute for Mathematics in the Sciences, Leipzig (Germany)

    2011-07-01

    In this third volume of his modern introduction to quantum field theory, Eberhard Zeidler examines the mathematical and physical aspects of gauge theory as a principle tool for describing the four fundamental forces which act in the universe: gravitative, electromagnetic, weak interaction and strong interaction. Volume III concentrates on the classical aspects of gauge theory, describing the four fundamental forces by the curvature of appropriate fiber bundles. This must be supplemented by the crucial, but elusive quantization procedure. The book is arranged in four sections, devoted to realizing the universal principle force equals curvature: Part I: The Euclidean Manifold as a Paradigm Part II: Ariadne's Thread in Gauge Theory Part III: Einstein's Theory of Special Relativity Part IV: Ariadne's Thread in Cohomology For students of mathematics the book is designed to demonstrate that detailed knowledge of the physical background helps to reveal interesting interrelationships among diverse mathematical topics. Physics students will be exposed to a fairly advanced mathematics, beyond the level covered in the typical physics curriculum. Quantum Field Theory builds a bridge between mathematicians and physicists, based on challenging questions about the fundamental forces in the universe (macrocosmos), and in the world of elementary particles (microcosmos). (orig.)

  3. Do Class III patients have a different growth spurt than the general population?

    Science.gov (United States)

    Lee, Yun-Sik; Lee, Shin-Jae; An, Hongseok; Donatelli, Richard E; Kim, Soo-Hwan

    2012-11-01

    Understanding the timing and length of the growth spurt of Class III prognathic patients is fundamental to the strategy of interceptive orthopedic orthodontics as well as to the timing of orthognathic surgery. Consequently, this study was undertaken to determine whether there are any significant differences in the stature growth pattern of Class III subjects compared with non-Class III subjects and the general population. Twelve-year longitudinal stature growth data were collected for 402 randomly selected adolescents in the general population, 55 Class III mandibular prognathic patients, and 37 non-Class III patients. The growth data were analyzed by using the traditional linear interpolation method and nonlinear growth functions. The 6 stature growth parameters were measured: age at takeoff, stature at takeoff, velocity at takeoff, age at peak height velocity, stature at peak height velocity, and velocity at peak height velocity. Comparisons in the stature growth parameters and 15 cephalometric variables among the general population, Class III subjects, and non-Class III subjects were made with multivariate analysis. Patients with Class III prognathism did not have different growth parameters compared with Class II subjects or the general population. This study does not allow meaningful conclusions with regard to the relationship of mandibular size and stature growth pattern. The application of nonlinear growth curves vs the traditional linear interpolation method was also discussed. Copyright © 2012 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

  4. Gait and Function in Class III Obesity

    Directory of Open Access Journals (Sweden)

    Catherine Ling

    2012-01-01

    Full Text Available Walking, more specifically gait, is an essential component of daily living. Walking is a very different activity for individuals with a Body Mass Index (BMI of 40 or more (Class III obesity compared with those who are overweight or obese with a BMI between 26–35. Yet all obesity weight classes receive the same physical activity guidelines and recommendations. This observational study examined the components of function and disability in a group with Class III obesity and a group that is overweight or has Class I obesity. Significant differences were found between the groups in the areas of gait, body size, health condition, and activity capacity and participation. The Timed Up and Go test, gait velocity, hip circumference, and stance width appear to be most predictive of activity capacity as observed during gait assessment. The findings indicate that Class III-related gait is pathologic and not a normal adaptation.

  5. BALTICA III. Plant condition and life management

    International Nuclear Information System (INIS)

    Hietanen, S.; Auerkari, P.

    1995-01-01

    The BALTICA III, International Conference on Plant Condition and Life Management was held on June 6 - 8, 1995 on board Silja Serenade on its cruise between Helsinki - Stockholm and at the Forest Lake Hotel Korpilampi in Espoo. BALTICA III provides forum for the transfer of technology from applied research to practise. This is the second volume of the publications, which contain the presentations given at the BALTICA III, Plant Condition and Life Management. A total of 45 articles report recent experience in plant condition and life management. The conference focuses on recent applications that have been demonstrated for the benefit of safe and economical operation of power plants. Practical approach is emphasised, including the presentations that aim to provide insight into new techniques, improvements in assessment methodologies as well as maintenance strategies. Compared to earlier occasions in the BALTICA series, a new aspect is in the applications of knowledge-based systems in the service of power plant life management. (orig.)

  6. Structural systematics of rare earth complexes. III. Structural characterization of lanthanoid (III) picrate hydrates: gadolinium picrate dodecahydrate - an x-ray-induced phase modifications? - and some general aspects of structural chemistry of lanthanoid picrates

    International Nuclear Information System (INIS)

    Harrowfield, J.M.; Weimin, Lu; Brian, W.S.; White, A.H.

    1994-01-01

    In the course of the previous studies (Parts I and II), an unusual result was observed in the case of the structure determination of hydrated gadolinium(III) picrate. Midway through data collection, the monoclinic P2 1 /c phase modification (X-ray-induced?) to a similar cell more nearly resembling that of the La→Pr structure type recorded previously, with no loss of crystal integrity, and with useful data sets being obtained on both forms. Redetermination of the structure with a fresh sample yielded no reproduction of the anomaly. These results are recorded and discussed, together with an overview of the consequences of the data of Parts I-III in relation to those of other literature in the field. 13 refs., 4 tabs., 1 fig

  7. Transport properties of gaseous ions over a wide energy range. Part III

    International Nuclear Information System (INIS)

    Ellis, H.W.; Thackston, M.G.; McDaniel, E.W.; Mason, E.A.

    1984-01-01

    This paper updates and extends in scope our two previous papers entitled ''Transport Properties of Gaseous Ions over a Wide Energy Range.'' The references to the earlier publications (referred to as ''Part I'' and ''Part II'') are I, H. W. Ellis, R. Y. Pai, E. W. McDonald, E. A. Mason, and L. A. Viehland, ATOMIC DATA AND NUCLEAR DATA TABLES 17, 177--210 (19876); and II, H. W. Ellis, E. W. McDaniel, D. L. Albritton, L. A. Veihland, S. L. Lin, and E. A. Mason, ATOMIC DATA AND NUCLEAR DATA TABLES 22, 179--217 (1978). Parts I and II contained compilations of experimental data on ionic mobilities and diffusion coefficients (both longitudinal and transverse) for ions in neutral gase (almost exclusively at room temperature) in an externally applied electric field

  8. Laparoscopic Treatment of Type III Mirizzi Syndrome by T-Tube Drainage

    Directory of Open Access Journals (Sweden)

    Fahri Yetışır

    2016-01-01

    Full Text Available Mirizzi syndrome (MS is an impacted stone in the cystic duct or Hartmann’s pouch that mechanically obstructs the common bile duct. We would like to report laparoscopic treatment of type III MS. A 75-year-old man was admitted with the complaint of abdominal pain and jaundice. The patient was accepted as MS type III according to radiological imaging and intraoperative view. Laparoscopic subtotal cholecystectomy, extraction of impacted stone by opening anterior surface of dilated cystic duct and choledochus, and repair of this opening by using the remaining part of gallbladder over the T-tube drainage were performed in a patient with type III MS. Application of reinforcement suture over stump was done in light of the checking with oliclinomel N4 injection trough the T-tube. At the 18-month follow-up, he was symptom-free with normal liver function tests.

  9. In pursuit of vehicle landmine occupant protection: Evaluating the dynamic response characteristic of the military lower extremity leg (MiL-Lx) compared to the Hybrid III (HIII) lower leg

    CSIR Research Space (South Africa)

    Pandelani, T

    2010-09-01

    Full Text Available typical mine-protected vehicle landmine blast load conditions. Tests were performed using the Lower Limb Impactor (LLI) on both the MiL-Lx leg and the Hybrid III leg, and the relative responses compared. The results show that the MiL-Lx leg appears...

  10. Doublet III neutral beam multi-stream command language system

    International Nuclear Information System (INIS)

    Campbell, L.; Garcia, J.R.

    1983-01-01

    A multi-stream command language system was developed to provide control of the dual source neutral beam injectors on the Doublet III experiment at GA Technologies Inc. The Neutral Beam command language system consists of three parts: compiler, sequencer, and interactive task. The command language, which was derived from the Doublet III tokamak command language, POPS, is compiled, using a recursive descent compiler, into reverse polish notation instructions which then can be executed by the sequencer task. The interactive task accepts operator commands via a keyboard. The interactive task directs the operation of three input streams, creating commands which are then executed by the sequencer. The streams correspond to the two sources within a Doublet III neutral beam, plus an interactive stream. The sequencer multiplexes the execution of instructions from these three streams. The instructions include reads and writes to an operator terminal, arithmetic computations, intrinsic functions such as CAMAC input and output, and logical instructions. The neutral beam command language system was implemented using Modular Computer Systems (ModComp) Pascal and consists of two tasks running on a ModComp Classic IV computer. The two tasks, the interactive and the sequencer, run independently and communicate using shared memory regions. The compiler runs as an overlay to the interactive task when so directed by operator commands. The system is succesfully being used to operate the three neutral beams on Doublet III

  11. Alimentos industrializados congelados gama III y IV

    OpenAIRE

    Tupone Reverter, Paula

    2012-01-01

    El presente estudio tiene como objetivo, indagar sobre el consumo, el grado de información y contenido de sodio, grasas saturadas y colesterol de los principales alimentos congelados Gama III y V consumidos por los encuestados. A partir de esto, se realiza una encuesta de frecuencia de consumo y preguntas varias a 250 personas de entre 30 a 60 años, que concurren a cuatro supermercados de la ciudad de Mar del Plata, para determinar el conocimiento por parte de los encuestados e...

  12. Exploring Flipped Classroom Instruction in Calculus III

    Science.gov (United States)

    Wasserman, Nicholas H.; Quint, Christa; Norris, Scott A.; Carr, Thomas

    2017-01-01

    In an undergraduate Calculus III class, we explore the effect of "flipping" the instructional delivery of content on both student performance and student perceptions. Two instructors collaborated to determine daily lecture notes, assigned the same homework problems, and gave identical exams; however, compared to a more traditional…

  13. Multiscale structural characterizations of mixed U(iv)-An(iii) oxalates (An(iii) = Pu or Am) combining XAS and XRD measurements.

    Science.gov (United States)

    Arab-Chapelet, B; Martin, P M; Costenoble, S; Delahaye, T; Scheinost, A C; Grandjean, S; Abraham, F

    2016-04-28

    Mixed actinide(III,IV) oxalates of the general formula M2.2UAn(C2O4)5·nH2O (An = Pu or Am and M = H3O(+) and N2H5(+)) have been quantitatively precipitated by oxalic precipitation in nitric acid medium (yield >99%). Thorough multiscale structural characterization using XRD and XAS measurements confirmed the existence of mixed actinide oxalate solid solutions. The XANES analysis confirmed that the oxidation states of the metallic cations, tetravalent for uranium and trivalent for plutonium and americium, are maintained during the precipitation step. EXAFS measurements show that the local environments around U(+IV), Pu(+III) and Am(+III) are comparable, and the actinides are surrounded by ten oxygen atoms from five bidentate oxalate anions. The mean metal-oxygen distances obtained by XAS measurements are in agreement with those calculated from XRD lattice parameters.

  14. Head and Neck Squamous Cell Carcinomas Do Not Express EGFRvIII

    Energy Technology Data Exchange (ETDEWEB)

    Melchers, Lieuwe J., E-mail: l.j.melchers@umcg.nl [Department of Oral and Maxillofacial Surgery, University Medical Center Groningen, University of Groningen, Groningen (Netherlands); Department of Pathology, University Medical Center Groningen, University of Groningen, Groningen (Netherlands); Clausen, Martijn J.A.M. [Department of Oral and Maxillofacial Surgery, University Medical Center Groningen, University of Groningen, Groningen (Netherlands); Department of Pathology, University Medical Center Groningen, University of Groningen, Groningen (Netherlands); Mastik, Mirjam F. [Department of Pathology, University Medical Center Groningen, University of Groningen, Groningen (Netherlands); Slagter-Menkema, Lorian [Department of Pathology, University Medical Center Groningen, University of Groningen, Groningen (Netherlands); Department of Otorhinolaryngology/Head and Neck Surgery, University Medical Center Groningen, University of Groningen, Groningen (Netherlands); Langendijk, Johannes A. [Department of Radiation Oncology, University Medical Center Groningen, University of Groningen, Groningen (Netherlands); Laan, Bernard F.A.M. van der [Department of Otorhinolaryngology/Head and Neck Surgery, University Medical Center Groningen, University of Groningen, Groningen (Netherlands); Wal, Jacqueline E. van der; Vegt, Bert van der [Department of Pathology, University Medical Center Groningen, University of Groningen, Groningen (Netherlands); Roodenburg, Jan L.N. [Department of Oral and Maxillofacial Surgery, University Medical Center Groningen, University of Groningen, Groningen (Netherlands); Schuuring, Ed [Department of Pathology, University Medical Center Groningen, University of Groningen, Groningen (Netherlands)

    2014-10-01

    Purpose: To assess the prevalence of EGFRvIII, a specific variant of EGFR (epidermal growth factor receptor), in 3 well-defined cohorts of head and neck squamous cell carcinoma (HNSCC). Methods and Materials: Immunohistochemistry for the specific detection of EGFRvIII using the L8A4 antibody was optimized on formalin-fixed, paraffin-embedded tissue using glioblastoma tissue. It was compared with EGFR and EGFRvIII RNA expression using a specific reverse transcription–polymerase chain reaction also optimized for formalin-fixed, paraffin-embedded tissue. Tissue microarrays including 531 HNSCCs of various stages with complete clinicopathologic and follow-up data were tested for the presence of EGFRvIII. Results: None of the 531 cases showed EGFRvIII protein expression. Using an immunohistochemistry protocol reported by others revealed cytoplasmic staining in 8% of cases. Reverse transcription–polymerase chain reaction for the EGFRvIII transcript of the 28 highest cytoplasmic staining cases, as well as 69 negative cases, did not show expression in any of the tested cases, suggesting aspecific staining by a nonoptimal protocol. Conclusions: The EGFRvIII mutation is not present in HNSCC. Therefore, EGFRvIII does not influence treatment response in HNSCC and is not a usable clinical prognostic marker.

  15. Head and Neck Squamous Cell Carcinomas Do Not Express EGFRvIII

    International Nuclear Information System (INIS)

    Melchers, Lieuwe J.; Clausen, Martijn J.A.M.; Mastik, Mirjam F.; Slagter-Menkema, Lorian; Langendijk, Johannes A.; Laan, Bernard F.A.M. van der; Wal, Jacqueline E. van der; Vegt, Bert van der; Roodenburg, Jan L.N.; Schuuring, Ed

    2014-01-01

    Purpose: To assess the prevalence of EGFRvIII, a specific variant of EGFR (epidermal growth factor receptor), in 3 well-defined cohorts of head and neck squamous cell carcinoma (HNSCC). Methods and Materials: Immunohistochemistry for the specific detection of EGFRvIII using the L8A4 antibody was optimized on formalin-fixed, paraffin-embedded tissue using glioblastoma tissue. It was compared with EGFR and EGFRvIII RNA expression using a specific reverse transcription–polymerase chain reaction also optimized for formalin-fixed, paraffin-embedded tissue. Tissue microarrays including 531 HNSCCs of various stages with complete clinicopathologic and follow-up data were tested for the presence of EGFRvIII. Results: None of the 531 cases showed EGFRvIII protein expression. Using an immunohistochemistry protocol reported by others revealed cytoplasmic staining in 8% of cases. Reverse transcription–polymerase chain reaction for the EGFRvIII transcript of the 28 highest cytoplasmic staining cases, as well as 69 negative cases, did not show expression in any of the tested cases, suggesting aspecific staining by a nonoptimal protocol. Conclusions: The EGFRvIII mutation is not present in HNSCC. Therefore, EGFRvIII does not influence treatment response in HNSCC and is not a usable clinical prognostic marker

  16. Sorption of chromium(VI) and chromium(III) on aluminium hydroxide

    International Nuclear Information System (INIS)

    Music, S.

    1986-01-01

    Factors that influence the sorption of Cr(VI) and Cr(III) on aluminium hydroxide were investigated. The sorption of chromates decreases as the pH of the suspension increases. The mechanism of CrOsub(4)sup(2-) sorption was interpreted in terms of reactions between chromates and -OH and/or Hsub(2)O groups at the hydroxide/liquid interface. It was shown that chromates are more tightly sorbed on aluminium hydroxide compared to other anions, e.g. chlorides. On the other hand, specifically absorbed anions, such as molybdates, compete strongly with chromates for the sorption sites. The sorption of chromium(III) increases with the pH of the suspension. Also, the sorption of chromium(III) is suppressed in the presence of citrate ions. The best conditions for the fixation of Cr(VI) and Cr(III) by aluminium hydroxide are presented. (author)

  17. Eighth annual meeting, Vienna, Austria, 15-18 April 1975. Summary report. Part III

    International Nuclear Information System (INIS)

    1976-01-01

    The Summary Report of the Eighth Annual Meeting of the International Working Group on Fast Reactors contains the minutes of the meeting (Part 1); papers which review the national programmes in the field of LMFBRs (Part 2) and the discussions on the review of national programmes (Part 3). The agenda of the meeting involved design, construction, operating experiences of demonstration fast power reactors, reprocessing of spent fuel from LMFBRs, reliability of decay heat removal systems, fuel failure mechanisms, safety of LMFBRs

  18. Eighth annual meeting, Vienna, Austria, 15-18 April 1975. Summary report. Part III

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-01-01

    The Summary Report of the Eighth Annual Meeting of the International Working Group on Fast Reactors contains the minutes of the meeting (Part 1); papers which review the national programmes in the field of LMFBRs (Part 2) and the discussions on the review of national programmes (Part 3). The agenda of the meeting involved design, construction, operating experiences of demonstration fast power reactors, reprocessing of spent fuel from LMFBRs, reliability of decay heat removal systems, fuel failure mechanisms, safety of LMFBRs.

  19. Role of Peroxiredoxin III in the Pathogenesis of Pre-eclampsia as Evidenced in Mice

    Directory of Open Access Journals (Sweden)

    Lianqin Li

    2010-01-01

    Full Text Available As a member of peroxiredoxin (Prx family, PrxIII has been demonstrated to play an important role in scavenging intracellular reactive oxygen species (ROS. Since PrxIII knockout mice exhibited oxidative stress in placentas resembling pathophysiologic changes in placentas of human pre-eclampsia, we measured blood pressure through the carotid artery and detected oxidative status by western blotting in pregnant mice. We did not notice hypertension in pregnant PrxIII knockout mice as compared with wild-type littermates, although endothelin-1 was overexpressed in PrxIII-deficient placentas. Our results indicate that PrxIII is not involved in pre-eclamptic development. Instead, PrxIII is an indispensable antioxidant in placentas where oxidative stress exists.

  20. [EUROASPIRE III: a comparison between Turkey and Europe].

    Science.gov (United States)

    Tokgözoğlu, Lale; Kaya, Ergün Bariş; Erol, Cetin; Ergene, Oktay

    2010-04-01

    The EUROASPIRE III survey was conducted in 2006-2007 in 22 countries in Europe (76 centers) to describe risk factors, lifestyle and therapeutic management of patients with coronary heart disease (CHD), compliance with current guidelines, and to document changes over time. This study aimed to assess the results of the EUROASPIRE III survey in terms of differences between Turkey and other European countries. The results of the EUROASPIRE III survey were compared with those of 17 centers from Turkey. Consecutive patients with a diagnosis of CHD (669 medical records, 23.8% women) were identified retrospectively, of which 338 patients (50.5%) were followed-up, interviewed, and examined at least six months after the index event (acute coronary syndrome or interventional procedure). Compared to the EUROASPIRE III data, recordings from Turkey's centers at discharge on classical risk factors did not exhibit remarkable differences; however, data on weight, height, waist circumference, lipid profile, glucose, and HbA1c measurements were more incomplete. In comparison to Europe population, the most important differences were observed in the higher rates of the following: young patients with myocardial infarction (>50 years, 20% vs. 12.7%), persistence in smoking (23.1% vs. 17.2%), immobility, low HDL-cholesterol (50.2% vs. 36.7%), insufficient follow-up by physicians after the index event (12% vs. 2.2%-except Turkey), and insufficient patient education. The data from the Turkey arm of the survey show that efforts for cardiovascular disease prevention fall short of the targets, similar to Europe.

  1. Radiobiology in clinical radiation therapy - Part III: Normal tissue damage

    International Nuclear Information System (INIS)

    Travis, Elizabeth L.

    1996-01-01

    Objective: This is the third part of a course designed for residents in radiation oncology preparing for their boards. This part of the course will focus on the mechanisms underlying damage in normal tissues. Although conventional wisdom long held that killing and depletion of a critical cell(s) in a tissue was responsible for the later expression of damage, histopathologic changes in normal tissue can now be explained and better understood in terms of the new molecular biology. The concept that depletion of a single cell type is responsible for the observed histopathologic changes in normal tissues has been replaced by the hypothesis that damage results from the interaction of many different cell systems, including epithelial, endothelial, macrophages and fibroblasts, via the production of specific autocrine, paracrine and endocrine growth factors. A portion of this course will discuss the clinical and experimental data on the production and interaction of those cytokines and cell systems considered to be critical to tissue damage. It had long been suggested that interindividual differences in radiation-induced normal tissue damage was genetically regulated, at least in part. Both clinical and experimental data supported this hypothesis but it is the recent advances in human and mouse molecular genetics which have provided the tools to dissect out the genetic component of normal tissue damage. These data will be presented and related to the potential to develop genetic markers to identify sensitive individuals. The impact on clinical outcome of the ability to identify prospectively sensitive patients will be discussed. Clinically it is well-accepted that the volume of tissue irradiated is a critical factor in determining tissue damage. A profusion of mathematical models for estimating dose-volume relationships in a number of organs have been published recently despite the fact that little data are available to support these models. This course will review the

  2. Basel III D: Swiss Finish to Basel III

    OpenAIRE

    Christian M. McNamara; Natalia Tente; Andrew Metrick

    2014-01-01

    After the Basel Committee on Banking Supervision (BCBS) introduced the Basel III framework in 2010, individual countries confronted the question of how best to implement the framework given their unique circumstances. Switzerland, with a banking industry that is both heavily concentrated and very large relative to the size of its overall economy, faced a special challenge. It ultimately adopted what is sometimes referred to as the “Swiss Finish” to Basel III – enhanced requirements applicable...

  3. Binary and ternary chelates of Sc(III), Y(III) and La(III) with ethylenediamine tetraacetic acid as primary ligand and substituted salicylic acids as secondary ligands

    Energy Technology Data Exchange (ETDEWEB)

    Pandey, A K; Chandra, M; Agarwala, B V; Dey, A K [Allahabad Univ. (India). Chemical Labs.

    1980-02-01

    Study of ternary complex formation of several tripositive metal ions viz. Sc(III), Y(III) and La(III) with ethylenediamine tetraacetic acid (EDTA) as a primary ligand and 5-chlorosalicylic acid (CSA) or 3,5-dibromosalicylic acid (DBSA) as secondary ligands by pH-metric titration technique is reported. The stability order of metal chelates with respect to ligands is observed to be DBSA>CSA and with respect to metal ions Sc(III)>Y(III)>La(III).

  4. Semiconducting III-V compounds

    CERN Document Server

    Hilsum, C; Henisch, Heinz R

    1961-01-01

    Semiconducting III-V Compounds deals with the properties of III-V compounds as a family of semiconducting crystals and relates these compounds to the monatomic semiconductors silicon and germanium. Emphasis is placed on physical processes that are peculiar to III-V compounds, particularly those that combine boron, aluminum, gallium, and indium with phosphorus, arsenic, and antimony (for example, indium antimonide, indium arsenide, gallium antimonide, and gallium arsenide).Comprised of eight chapters, this book begins with an assessment of the crystal structure and binding of III-V compounds, f

  5. Basel III Liquidity Risk Measures and Bank Failure

    Directory of Open Access Journals (Sweden)

    L. N. P. Hlatshwayo

    2013-01-01

    Full Text Available Basel III banking regulation emphasizes the use of liquidity coverage and nett stable funding ratios as measures of liquidity risk. In this paper, we approximate these measures by using global liquidity data for 391 hand-selected, LIBOR-based, Basel II compliant banks in 36 countries for the period 2002 to 2012. In particular, we compare the risk sensitivity of the aforementioned Basel III liquidity risk measures to those of traditional measures such as the nonperforming assets ratio, return-on-assets, LIBOR-OISS, Basel II Tier 1 capital ratio, government securities ratio, and brokered deposits ratio. Furthermore, we use a discrete-time hazard model to study bank failure. In this regard, we find that Basel III risk measures have limited ability to predict bank failure when compared with their traditional counterparts. An important result is that a higher liquidity coverage ratio is associated with a higher bank failure rate. We also find that market-wide liquidity risk (proxied by LIBOR-OISS was the major predictor of bank failures in 2009 and 2010 while idiosyncratic liquidity risk (proxied by other liquidity risk measures was less. In particular, our contribution is the first to achieve these results on a global scale over a relatively long period for a variety of banks.

  6. Characterization and complexation of humic acids. Part 1

    International Nuclear Information System (INIS)

    Kim, J.L.; Buckau, G.; Klenze, R.; Rhee, D.S.; Wimmer, H.

    1991-01-01

    This paper summarizes the research contributions to the CEC Mirage II project, particularly the research area on complexation and colloids (COCO). The first part of the paper comprises the characterization of humic and fulvic acids from different origins: a commercial product from the Aldrich Co. used as a reference humic acid and site-specific humic acids from Gorleben (Germany), Boom Clay (Belgium) and Fanay Augeres (France) aquifer systems. The second part includes the complexation of trivalent actinides: Am(III) and Cm(III) with various humic acids. A number of different methods have been applied for the complexation study: spectrophotometry, ultrafiltration, laser-induced photo-acoustic spectroscopy (LPAS) and time-resolved laser fluorescence spectroscopy (TRLFS). The evaluation process of complexation constant is discussed extensively and the well consolidated results are presented, which can be directly used for the geochemical modelling of the radionuclide migration

  7. Separation of Am(III) from Eu(III) by mixtures of triazynylbipyridine and bis(dicarbollide) extractants. The composition of the metal complexes extracted

    International Nuclear Information System (INIS)

    Narbutt, J.; Krejzler, J.

    2006-01-01

    Separation of trivalent actinides, in particular americium and curium, from lanthanides is an important step in an advanced partitioning process for future reprocessing of spent nuclear fuels. The use of soft donor (N and S) ligands makes it possible to separate the two groups of elements, probably because of the more covalent character in the complexes with actinides compared to the lanthanides. The aim of present work was to study solvent extraction of Am(III) and Eu(III) in a similar system with diethylhemi-BTP and COSAN: protonated bis(chlorodicarbollido)cobalt(III) or commo-3,3-cobalta-bis(8,9,12-trichlora-1,2-dicarbaclosododecaborane)ic acid. The present research was focused on both the determination of conditions for the separation of 241 Am(III) from 152 Eu in aqueous nitrate solution by using a synergistic extraction system and on the modelling of the process by slope analysis. Obtained values of the separation factors supported by the computer modelling permitted drawing the conclusions on the mechanism of the process and on the structure of extracted species

  8. Rbs1, a new protein implicated in RNA polymerase III biogenesis in yeast Saccharomyces cerevisiae.

    Science.gov (United States)

    Cieśla, Małgorzata; Makała, Ewa; Płonka, Marta; Bazan, Rafał; Gewartowski, Kamil; Dziembowski, Andrzej; Boguta, Magdalena

    2015-04-01

    Little is known about the RNA polymerase III (Pol III) complex assembly and its transport to the nucleus. We demonstrate that a missense cold-sensitive mutation, rpc128-1007, in the sequence encoding the C-terminal part of the second largest Pol III subunit, C128, affects the assembly and stability of the enzyme. The cellular levels and nuclear concentration of selected Pol III subunits were decreased in rpc128-1007 cells, and the association between Pol III subunits as evaluated by coimmunoprecipitation was also reduced. To identify the proteins involved in Pol III assembly, we performed a genetic screen for suppressors of the rpc128-1007 mutation and selected the Rbs1 gene, whose overexpression enhanced de novo tRNA transcription in rpc128-1007 cells, which correlated with increased stability, nuclear concentration, and interaction of Pol III subunits. The rpc128-1007 rbs1Δ double mutant shows a synthetic growth defect, indicating that rpc128-1007 and rbs1Δ function in parallel ways to negatively regulate Pol III assembly. Rbs1 physically interacts with a subset of Pol III subunits, AC19, AC40, and ABC27/Rpb5. Additionally, Rbs1 interacts with the Crm1 exportin and shuttles between the cytoplasm and nucleus. We postulate that Rbs1 binds to the Pol III complex or subcomplex and facilitates its translocation to the nucleus. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

  9. Progressive changes in patients with skeletal Class III malocclusion treated by 2-jaw surgery with minimal and conventional presurgical orthodontics: A comparative study.

    Science.gov (United States)

    Zhou, Yang; Li, Zili; Wang, Xiaoxia; Zou, Bingshuang; Zhou, Yanheng

    2016-02-01

    In this study, we aimed to compare treatment efficacy and postsurgical stability between minimal presurgical orthodontics and conventional presurgical orthodontics for patients with skeletal Class III malocclusion. Forty patients received minimal presurgical orthodontics (n = 20) or conventional presurgical orthodontics (n = 20). Lateral cephalograms were obtained before treatment, before orthognathic surgery, and at 1 week, 3 months, 6 months, and 12 months after surgery. Changes of overjet and mandibular incisal angle before surgery were greater in the conventional presurgical orthodontics group than in the minimal presurgical orthodontics group. Postsurgical horizontal changes in Points A and B, overjet, and mandibular incisal angle showed significant differences among the time points. Most of the horizontal and vertical relapses in the maxilla and the mandible occurred within the first 6 months in both groups. Minimal presurgical orthodontics and conventional presurgical orthodontics showed similar extents and directions of skeletal changes in patients with Class III malocclusion. However, orthodontists and surgeons should preoperatively consider the postsurgical counterclockwise rotation of the mandible when using minimal presurgical orthodontics. Close and frequent observations are recommended in the early postsurgical stages. Copyright © 2016 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

  10. Development of a C3-symmetric benzohydroxamate tripod: Trimetallic complexation with Fe(III), Cr(III) and Al(III)

    Science.gov (United States)

    Baral, Minati; Gupta, Amit; Kanungo, B. K.

    2016-06-01

    The design, synthesis and physicochemical characterization of a C3-symmetry Benzene-1,3,5-tricarbonylhydroxamate tripod, noted here as BTHA, are described. The chelator was built from a benzene as an anchor, symmetrically extended by three hydroxamate as ligating moieties, each bearing O, O donor sites. A combination of absorption spectrophotometry, potentiometry and theoretical investigations are used to explore the complexation behavior of the ligand with some trivalent metal ions: Fe(III), Cr(III), and Al(III). Three protonation constants were calculated for the ligand in a pH range of 2-11 in a highly aqueous medium (9:1 H2O: DMSO). A high rigidity in the molecular structure restricts the formation of 1:1 (M/L) metal encapsulation but shows a high binding efficiency for a 3:1 metal ligand stoichiometry giving formation constant (in β unit) 28.73, 26.13 and 19.69 for [M3L]; Mdbnd Fe(III), Al(III) and Cr(III) respectively, and may be considered as an efficient Fe-carrier. The spectrophotometric study reveals of interesting electronic transitions occurred during the complexation. BTHA exhibits a peak at 238 nm in acidic pH and with the increase of pH, a new peak appeared at 270 nm. A substantial shifting in both of the peaks in presence of the metal ions implicates a s coordination between ligand and metal ions. Moreover, complexation of BTHA with iron shows three distinct colors, violet, reddish orange and yellow in different pH, enables the ligand to be considered for the use as colorimetric sensor.

  11. Skeletal, dental and soft tissue changes in Class III patients treated with fixed appliances and lower premolar extractions.

    Science.gov (United States)

    Abu Alhaija, Elham S J; Al-Khateeb, Susan N

    2011-05-01

    Mild Class III malocciusions can be treated by upper incisor proclination and lower incisor retroclination following extraction of the lower first premolars. To compare the skeletal, dental and soft tissue changes in Class III patients treated with fixed appliances, Class III traction and lower first premolar extractions with the changes in a group of untreated Class III patients. The Treatment group consisted of 30 Class III patients (Mean age 13.69 +/- 1.48 years) who were treated by upper and lower fixed appliances, Class III intermaxillary traction and lower first premolar extractions for 2.88 +/- 1.12 years. The Control group consisted of 20 untreated Class III patients (Mean age 13.51 +/- 0.95) matched for age and gender. The T1 to T2 changes in the treated and untreated groups were compared using a paired t-test while differences between the two groups were compared with an independent t-test. During treatment, the upper incisors were proclined about 1 degree and the lower incisors were retroclined 8 degrees. Small, but statistically significant changes in SNB, Wits and the overlying soft tissues accompanied the changes in incisor inclination. At the end of treatment a positive overbite and overjet were achieved. The increase in lower facial height in the Treatment group was comparable with the change in the Control group. A range of mild to moderate Class III malocclusions can be treated by dentoalveolar compensation.

  12. Hexakis(dimethyl sulfoxide-κOchromium(III trichloride

    Directory of Open Access Journals (Sweden)

    Turganbay S. Iskenderov

    2008-07-01

    Full Text Available In the title compound, [Cr(C2H6OS6]Cl3, each CrIII ion is located on a three-fold inversion axis and is coordinated by six dimethylsulfoxide ligands [Cr—O = 1.970 (2–1.972 (2 Å; O—Cr—O = 88.19 (9 and 91.81 (9°] in a slightly distorted octahedral geometry. The Cl− anions take part in the formation of weak C—H...Cl hydrogen bonds, which contribute to the crystal packing stabilization.

  13. Doublet III neutral beam multi-stream command language system

    International Nuclear Information System (INIS)

    Campbell, L.; Garcia, J.R.

    1983-12-01

    A multi-stream command language system was developed to provide control of the dual source neutral beam injectors on the Doublet III experiment at GA Technologies Inc. The Neutral Beam command language system consists of three parts: compiler, sequencer, and interactive task. The command language, which was derived from the Doublet III tokamak command language, POPS, is compiled, using a recursive descent compiler, into reverse polish notation instructions which then can be executed by the sequencer task. The interactive task accepts operator commands via a keyboard. The interactive task directs the operation of three input streams, creating commands which are then executed by the sequencer. The streams correspond to the two sources within a Doublet III neutral beam, plus an interactive stream. The sequencer multiplexes the execution of instructions from these three streams. The instructions include reads and writes to an operator terminal, arithmetic computations, intrinsic functions such as CAMAC input and output, and logical instructions. The neutral beam command language system was implemented using Modular Computer Systems (ModComp) Pascal and consists of two tasks running on a ModComp Classic IV computer

  14. Fluorimetric determination of samarium(III) and europium(III) in neodymium oxide by separation with a resin column

    Energy Technology Data Exchange (ETDEWEB)

    Shaorong Liu; Jian Meng (Beijing Research Institute of Chemical Engineering and Metallurgy (China)); Wenhua Liu (General Research Institute for Non-Ferrous Metals (China))

    1992-08-24

    When thenoyltrifluoroacetone-phenanthroline-Triton X-100 is used to determine samarium(III) and europium(III) fluorimetrically, only a limited amount of neodymium(III) can be tolerated. By using an on- line separation which can partially separate neodymium(III) from samarium(III), a practical and convenient method was developed to detect samarium(III) at concentrations >0.05% and europium(III) at concentrations >0.005% in neodymium oxide. (author). 7 refs.; 4 figs.; 3 tabs.

  15. Fluorimetric determination of samarium(III) and europium(III) in neodymium oxide by separation with a resin column

    International Nuclear Information System (INIS)

    Shaorong Liu; Jian Meng; Wenhua Liu

    1992-01-01

    When thenoyltrifluoroacetone-phenanthroline-Triton X-100 is used to determine samarium(III) and europium(III) fluorimetrically, only a limited amount of neodymium(III) can be tolerated. By using an on- line separation which can partially separate neodymium(III) from samarium(III), a practical and convenient method was developed to detect samarium(III) at concentrations >0.05% and europium(III) at concentrations >0.005% in neodymium oxide. (author). 7 refs.; 4 figs.; 3 tabs

  16. Operative treatment of acute acromioclavicular dislocations Rockwood III and V-Comparative study between K-wires combined with FiberTape(®) vs. TightRope System(®).

    Science.gov (United States)

    Vrgoč, G; Japjec, M; Jurina, P; Gulan, G; Janković, S; Šebečić, B; Starešinić, M

    2015-11-01

    Acromioclavicular (AC) joint dislocations usually occur in a young active population as a result of a fall on the shoulder. Rockwood divided these dislocations into six types. Optimal treatment is still a matter of discussion. Many operative techniques have been developed, but the main choice is between open and minimally-invasive arthroscopic procedures. The aim of this study was to compare two different surgical methods on two groups of patients to find out which method is superior in terms of benefit to the patient. The methods were evaluated through objective and subjective scores, with a focus on complications and material costs. A retrospective two-centre study was conducted in patients with acute AC joint dislocation Rockwood types III and V. The two methods conducted were an open procedure using K-wires combined with FiberTape(®) (Arthrex, Naples, USA) (Group 1) and an arthroscopic procedure using the TightRope System(®) (Arthrex, Naples, USA) (Group 2). Groups underwent procedures during a two-year period. Diagnosis was based on the clinical and radiographic examination of both AC joints. Surgical treatment and rehabilitation were performed. Sixteen patients were included in this study: Group 1 comprised 10 patients, all male, average age 41.6 years (range 17-64 years), Rockwood type III (eight patients) and Rockwood type V (two patients); Group 2 had six patients, one female and five male, average age 37.8 years (range 18-58 years), Rockwood type III (two patients) and Rockwood type V (four patients). Time from injury to surgery was shorter and patients needed less time to return to daily activities in Group 1. Duration of the surgical procedure was shorter in Group 2 compared with Group 1. Complications of each method were noted. According to the measured scores and operative outcome between dislocation Rockwood type III and V, no significant difference was found. Implant material used in Group 2 was 4.7 times more expensive than that used in Group 1

  17. Antibacterianos de acción sistémica: Parte III. Sulfonamidas y tetraciclinas

    Directory of Open Access Journals (Sweden)

    Manuel Cué Brugueras

    1999-04-01

    Full Text Available Resumen: Se presenta la tercera parte de una revisión bibliográfica sobre los antibacterianos de elección, en la cual se abordan los grupos sulfonamidas y tetraciclinas; además, se incluye un cuadro resumen con los antibióticos tratados en las tres partes, así como sus vías de administración y nombres comerciales que se utilizan en Cuba. Se hacen algunas consideraciones sobre la manera de enfrentar la gran variedad de antibióticos y el costo de la antibióticoterapia por parte de los países en vías de desarrollo, tomando como referencia algunas recomendaciones hechas por la OPS/OMSSummary: The third part of a bibliographic review on the elective antibacterials in which the groups of sulfonamides and tetracyclines are approached is presented. It is also included a summary picture with the antibiotics dealt with in the three parts, the routes of administration, and the trade names used in Cuba. Some considerations are made on the way to face the wide range of antibiotics and the cost of antibiotic therapy in the developing countries, taking into account some recommendations made by the PAHO/WHO

  18. Microbial dissimilatory iron(III) reduction: Studies on the mechanism and on processes of environmental relevance

    OpenAIRE

    Jahn, Michael

    2005-01-01

    Many microbes are able to respire aerobically oxygen or anaerobically other electron acceptors for example sulphate, nitrate, manganese(IV) or Fe(III). As iron minerals are widespread in nature, dissimilatory iron(III) reduction by different microorganisms is a very important process of anaerobic respiration. The general goal of this work was to improve the knowledge of processes, in which iron-reducing microbes are said to play an important role. For this purpose, in one part the focus wa...

  19. Air quality and climate change, Topic 3 of the Model Inter-Comparison Study for Asia Phase III (MICS-Asia III) - Part 1: Overview and model evaluation

    Science.gov (United States)

    Gao, Meng; Han, Zhiwei; Liu, Zirui; Li, Meng; Xin, Jinyuan; Tao, Zhining; Li, Jiawei; Kang, Jeong-Eon; Huang, Kan; Dong, Xinyi; Zhuang, Bingliang; Li, Shu; Ge, Baozhu; Wu, Qizhong; Cheng, Yafang; Wang, Yuesi; Lee, Hyo-Jung; Kim, Cheol-Hee; Fu, Joshua S.; Wang, Tijian; Chin, Mian; Woo, Jung-Hun; Zhang, Qiang; Wang, Zifa; Carmichael, Gregory R.

    2018-04-01

    Topic 3 of the Model Inter-Comparison Study for Asia (MICS-Asia) Phase III examines how online coupled air quality models perform in simulating high aerosol pollution in the North China Plain region during wintertime haze events and evaluates the importance of aerosol radiative and microphysical feedbacks. A comprehensive overview of the MICS-Asia III Topic 3 study design, including descriptions of participating models and model inputs, the experimental designs, and results of model evaluation, are presented. Six modeling groups from China, Korea and the United States submitted results from seven applications of online coupled chemistry-meteorology models. Results are compared to meteorology and air quality measurements, including data from the Campaign on Atmospheric Aerosol Research Network of China (CARE-China) and the Acid Deposition Monitoring Network in East Asia (EANET). The correlation coefficients between the multi-model ensemble mean and the CARE-China observed near-surface air pollutants range from 0.51 to 0.94 (0.51 for ozone and 0.94 for PM2.5) for January 2010. However, large discrepancies exist between simulated aerosol chemical compositions from different models. The coefficient of variation (SD divided by the mean) can reach above 1.3 for sulfate in Beijing and above 1.6 for nitrate and organic aerosols in coastal regions, indicating that these compositions are less consistent from different models. During clean periods, simulated aerosol optical depths (AODs) from different models are similar, but peak values differ during severe haze events, which can be explained by the differences in simulated inorganic aerosol concentrations and the hygroscopic growth efficiency (affected by varied relative humidity). These differences in composition and AOD suggest that future models can be improved by including new heterogeneous or aqueous pathways for sulfate and nitrate formation under hazy conditions, a secondary organic aerosol (SOA) formation chemical

  20. Validation of the Chinese version of Addenbrooke's Cognitive Examination III for diagnosing dementia.

    Science.gov (United States)

    Wang, Bian-Rong; Ou, Zhou; Gu, Xiao-Hua; Wei, Cun-Sheng; Xu, Jun; Shi, Jian-Quan

    2017-12-01

    The aim of this study was to validate the reliability of the Chinese version of Addenbrooke's Cognitive Examination III (ACE-III) for detecting dementia. Furthermore, the present study compares the diagnostic accuracy of ACE-III with that of mini-mental state examination (MMSE). One hundred seventy-seven patients with dementia and 180 healthy controls were included in the study. The reliability of ACE-III was very good (α-coefficient = 0.888). There was a significant negative correlation between Clinical Dementia Rating Scale score and total ACE-III score. Further, there was a positive correlation between MMSE score and total ACE-III score. Age exerted a significant effect on total ACE-III score, memory score, and language score. In the present study, the cutoff score of 83 showed a sensitivity of 91.1% and a specificity of 83.1%. The present findings support that the Chinese version of ACE-III is a reliable assessment tool for dementia. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

  1. Separation of valence forms of chromium(III) and chromium(VI) by coprecipitation with iron(III) hydroxide

    International Nuclear Information System (INIS)

    Nazirmadov, B.; Khamidov, B.O.; Egorova, L.A.

    1989-01-01

    The sorption of 9.62·10 -5 M of Cr (III) and Cr (VI) with iron hydroxide in 1 M potassium nitrate and potassium chloride was investigated in relation to the pH of the medium. Experimental data on the sorption of chromium(III) and chromium(VI) with iron(III) hydroxide made it possible to determine the region of practically complete concentration of Cr (III) and Cr (VI) (pH = 3-6.5). The results from spectrophotometric investigations, calculated data on the distribution of the hydroxocationic forms of chromium(III) and the anions of chromium(IV), and their sorption by iron-(III) hydroxide made it possible to characterize the sorbability of the cationic and anionic forms of chromium in various degrees of oxidation. On this basis a method was developed for the separation of chromium(III) and chromium(VI) by coprecipitation on iron(III) hydroxide and their separation from the iron(III) hydroxide support

  2. Syntheses, structures, and magnetic properties of a family of heterometallic heptanuclear [Cu5Ln2] (Ln = Y(III), Lu(III), Dy(III), Ho(III), Er(III), and Yb(III)) complexes: observation of SMM behavior for the Dy(III) and Ho(III) analogues.

    Science.gov (United States)

    Chandrasekhar, Vadapalli; Dey, Atanu; Das, Sourav; Rouzières, Mathieu; Clérac, Rodolphe

    2013-03-04

    Sequential reaction of the multisite coordination ligand (LH3) with Cu(OAc)2·H2O, followed by the addition of a rare-earth(III) nitrate salt in the presence of triethylamine, afforded a series of heterometallic heptanuclear complexes containing a [Cu5Ln2] core {Ln = Y(1), Lu(2), Dy(3), Ho(4), Er(5), and Yb(6)}. Single-crystal X-ray crystallography reveals that all the complexes are dicationic species that crystallize with two nitrate anions to compensate the charge. The heptanuclear aggregates in 1-6 are centrosymmetrical complexes, with a hexagonal-like arrangement of six peripheral metal ions (two rare-earth and four copper) around a central Cu(II) situated on a crystallographic inversion center. An all-oxygen environment is found to be present around the rare-earth metal ions, which adopt a distorted square-antiprismatic geometry. Three different Cu(II) sites are present in the heptanuclear complexes: two possess a distorted octahedral coordination sphere while the remaining one displays a distorted square-pyramidal geometry. Detailed static and dynamic magnetic properties of all the complexes have been studied and revealed the single-molecule magnet behavior of the Dy(III) and Ho(III) derivatives.

  3. Management strategies to effect change in intensive care units: lessons from the world of business. Part III. Effectively effecting and sustaining change.

    Science.gov (United States)

    Gershengorn, Hayley B; Kocher, Robert; Factor, Phillip

    2014-03-01

    Reaping the optimal rewards from any quality improvement project mandates sustainability after the initial implementation. In Part III of this three-part ATS Seminars series, we discuss strategies to create a culture for change, improve cooperation and interaction between multidisciplinary teams of clinicians, and position the intensive care unit (ICU) optimally within the hospital environment. Coaches are used throughout other industries to help professionals assess and continually improve upon their practice; use of this strategy is as of yet infrequent in health care, but would be easily transferable and potentially beneficial to ICU managers and clinicians alike. Similarly, activities focused on improving teamwork are commonplace outside of health care. Simulation training and classroom education about key components of successful team functioning are known to result in improvements. In addition to creating an ICU environment in which individuals and teams of clinicians perform well, ICU managers must position the ICU to function well within the hospital system. It is important to move away from the notion of a standalone ("siloed") ICU to one that is well integrated into the rest of the institution. Creating a "pull-system" (in which participants are active in searching out needed resources and admitting patients) can help ICU managers both provide better care for the critically ill and strengthen relationships with non-ICU staff. Although not necessary, there is potential upside to creating a unified critical care service to assist with achieving these ends.

  4. The Russia Corporate Governance Manual : Part I. Corporate Governance Introduced

    OpenAIRE

    International Finance Corporation; U.S. Department of Commerce

    2004-01-01

    The Russia corporate governance manual has been divided into and is published in six parts: (i) corporate governance introduced; (ii) good board practices; (iii) shareholder rights; (iv) information disclosure and transparency; (v) special focus section; and (vi) annexes model corporate governance documents. The first four parts contain chapters that focus on core corporate governance issu...

  5. Structural Characterization of Am(III)- and Pu(III)-DOTA Complexes.

    Science.gov (United States)

    Audras, Matthieu; Berthon, Laurence; Berthon, Claude; Guillaumont, Dominique; Dumas, Thomas; Illy, Marie-Claire; Martin, Nicolas; Zilbermann, Israel; Moiseev, Yulia; Ben-Eliyahu, Yeshayahu; Bettelheim, Armand; Cammelli, Sebastiano; Hennig, Christoph; Moisy, Philippe

    2017-10-16

    The complexation of 1,4,7,10-tetrazacyclodecane-1,4,7,10-tetraacetic acid (DOTA) ligand with two trivalent actinides (Am 3+ and Pu 3+ ) was investigated by UV-visible spectrophotometry, NMR spectroscopy, and extended X-ray absorption fine structure in conjunction with computational methods. The complexation process of these two cations is similar to what has been previously observed with lanthanides(III) of similar ionic radius. The complexation takes place in different steps and ends with the formation of a (1:1) complex [(An(III)DOTA)(H 2 O)] - , where the cation is bonded to the nitrogen atoms of the ring, the four carboxylate arms, and a water molecule to complete the coordination sphere. The formation of An(III)-DOTA complexes is faster than the Ln(III)-DOTA systems of equivalent ionic radius. Furthermore, it is found that An-N distances are slightly shorter than Ln-N distances. Theoretical calculations showed that the slightly higher affinity of DOTA toward Am over Nd is correlated with slightly enhanced ligand-to-metal charge donation arising from oxygen and nitrogen atoms.

  6. In vitro Comparative Evaluation of Various Restorative Materials used for restoring Class III Cavities in Deciduous Anterior Teeth: A Clinical Study.

    Science.gov (United States)

    Priyank, Harsh; Verma, Ankita; Gupta, Komal; Chaudhary, Esha; Khandelwal, Deepak; Nihalani, Shweta

    2016-12-01

    Beauty standards in today's modernized world scenario are formed by well-aligned and well-designed bright white teeth. One of the major reasons behind patients reporting to dental clinics is pain. Caries in the anterior primary teeth forms one of the major concerns from a restorative point of view. Very few studies are quoted in literature which stresses on the follow-up of anterior restorations in primary teeth. Hence, we evaluated and compared the efficacy of composite resin and resin-modified glass ionomer cement (RGIC) for class III restorations in primary anterior teeth. The present study was conducted in the pediatric dental wing and included a total of 80 patients aged 3 to 5½ years who reported with the chief complaint of carious lesions in the primary anterior teeth. Patients having minimal of a pair of similar appearing small carious lesions on the same proximal surfaces of the deciduous maxillary incisors were included for the study. All the patients were randomly divided into two groups: One in which RGIC restoration was done and other in which composite restoration was done. Cavity preparation was done and filling of the cavity with the restorative materials was carried out. Assessment of the restorations was done at 4, 8, and 12 months time following criteria given by Ryge et al. All the results were analyzed by Statistical Package for the Social Sciences (SPSS) software. Mann-Whitney test and one-way analysis of variance (ANOVA) were used to evaluate the level of significance; p value less than 0.05 was considered as significant. For composite and RGIC restorations, the mean score for anatomic shape was 1.21 and 1.10 respectively. While comparing the clinical parameters, nonsignificant results were obtained between composite and RGIC restorative materials at 4-, 8-, and 12-month interval. On comparing the clinical parameters for individual restorative materials at different time intervals, statistically significant results were obtained only for

  7. Synthesis, structure, luminescent, and magnetic properties of carbonato-bridged Zn(II)2Ln(III)2 complexes [(μ4-CO3)2{Zn(II)L(n)Ln(III)(NO3)}2] (Ln(III) = Gd(III), Tb(III), Dy(III); L(1) = N,N'-bis(3-methoxy-2-oxybenzylidene)-1,3-propanediaminato, L(2) = N,N'-bis(3-ethoxy-2-oxybenzylidene)-1,3-propanediaminato).

    Science.gov (United States)

    Ehama, Kiyomi; Ohmichi, Yusuke; Sakamoto, Soichiro; Fujinami, Takeshi; Matsumoto, Naohide; Mochida, Naotaka; Ishida, Takayuki; Sunatsuki, Yukinari; Tsuchimoto, Masanobu; Re, Nazzareno

    2013-11-04

    Carbonato-bridged Zn(II)2Ln(III)2 complexes [(μ4-CO3)2{Zn(II)L(n)Ln(III)(NO3)}2]·solvent were synthesized through atmospheric CO2 fixation reaction of [Zn(II)L(n)(H2O)2]·xH2O, Ln(III)(NO3)3·6H2O, and triethylamine, where Ln(III) = Gd(III), Tb(III), Dy(III); L(1) = N,N'-bis(3-methoxy-2-oxybenzylidene)-1,3-propanediaminato, L(2) = N,N'-bis(3-ethoxy-2-oxybenzylidene)-1,3-propanediaminato. Each Zn(II)2Ln(III)2 structure possessing an inversion center can be described as two di-μ-phenoxo-bridged {Zn(II)L(n)Ln(III)(NO3)} binuclear units bridged by two carbonato CO3(2-) ions. The Zn(II) ion has square pyramidal coordination geometry with N2O2 donor atoms of L(n) and one oxygen atom of a bridging carbonato ion at the axial site. Ln(III) ion is coordinated by nine oxygen atoms consisting of four from the deprotonated Schiff-base L(n), two from a chelating nitrate, and three from two carbonate groups. The temperature-dependent magnetic susceptibilities in the range 1.9-300 K, field-dependent magnetization from 0 to 5 T at 1.9 K, and alternating current magnetic susceptibilities under the direct current bias fields of 0 and 1000 Oe were measured. The magnetic properties of the Zn(II)2Ln(III)2 complexes are analyzed on the basis of the dicarbonato-bridged binuclear Ln(III)-Ln(III) structure, as the Zn(II) ion with d(10) electronic configuration is diamagnetic. ZnGd1 (L(1)) and ZnGd2 (L(2)) show a ferromagnetic Gd(III)-Gd(III) interaction with J(Gd-Gd) = +0.042 and +0.028 cm(-1), respectively, on the basis of the Hamiltonian H = -2J(Gd-Gd)ŜGd1·ŜGd2. The magnetic data of the Zn(II)2Ln(III)2 complexes (Ln(III) = Tb(III), Dy(III)) were analyzed by a spin Hamiltonian including the crystal field effect on the Ln(III) ions and the Ln(III)-Ln(III) magnetic interaction. The Stark splitting of the ground state was so evaluated, and the energy pattern indicates a strong easy axis (Ising type) anisotropy. Luminescence spectra of Zn(II)2Tb(III)2 complexes were observed, while those

  8. Tritium system design for the mirror reactors FPD-I, FPD-II, and FPD-III

    International Nuclear Information System (INIS)

    Finn, P.A.

    1985-01-01

    The tritium system design for the Fusion Power Demonstration Reactor (FPD-I, II, and III) is described. The device operates at 25% availability. For FPD-II, an engineering mode using tritium neutral beams is part of the design

  9. WISC-III e WAIS-III na avaliação da inteligência de cegos WISC-III/WAIS-III en ciegos WISC-III and WAIS-III in intellectual assessment of blind people

    OpenAIRE

    Elizabeth do Nascimento; Carmen Elvira Flores-Mendoza

    2007-01-01

    Diante da escassez de pesquisas nacionais e de testes psicológicos destinados a avaliar pessoas cegas, desenvolveu-se um estudo psicométrico com as escalas verbais dos testes WISC-III e WAIS-III. Após as adaptações de alguns estímulos e das instruções, os testes foram aplicados em crianças (N = 120) e adultos (N = 52) residentes em Belo Horizonte. Os resultados indicaram que as escalas verbais modificadas apresentam uma boa consistência interna (alfa> 0,80). Além disso, a investigação da vali...

  10. Compounds of type Ba/sub 2/Bsup(III)Ossup(V)O/sub 6/

    Energy Technology Data Exchange (ETDEWEB)

    Treiber, U; Kemmler-Sack, S [Tuebingen Univ. (Germany, F.R.). Lehrstuhl fuer Anorganische Chemie 2

    1981-07-01

    The black perovskites of type Ba/sub 2/Bsup(III)Ossup(V)O/sub 6/ crystallize cubic (Bsup(III) = Pr, Nd, Sm-Lu, Y) and rhombohedral (Bsup(III) = La) respectively; the cell volumina decrease linearily with (rsub(B)sup(III))/sup 3/. Intensity calculations on powder data for Ba/sub 2/YOsO/sub 6/ (space group Fm3m-Osub(h)/sup 5/) and Ba/sub 2/LaOsO/sub 6/ (space group R-3m-Dsub(3d)/sup 5/) gave the intensity related R'values of 4.6% and 5.0% respectively. The results of the vibrational spectroscopic investigations are reported in common with the bond orders, M-O distances and mean amplitudes and compared with the corresponding values of the series Ba/sub 2/Bsup(III)Irsup(V)O/sub 6/ and Ba/sub 2/Bsup(III)Rusup(V)O/sub 6/.

  11. Spectroscopic investigation of complexation of Cm(III) und Eu(III) with partitioning-relevant N-donor ligands

    International Nuclear Information System (INIS)

    Bremer, Antje

    2014-01-01

    The separation of trivalent actinides and lanthanides is an essential part of the development of improved nuclear fuel cycles. Liquid-liquid extraction is an applicable technique to achieve this separation. Due to the chemical similarity and the almost identical ionic radii of trivalent actinides and lanthanides this separation is, however, only feasible with highly selective extracting agents. It has been proven that molecules with soft sulphur or nitrogen donor atoms have a higher affinity for trivalent actinides. In the present work, the complexation of Cm(III) and Eu(III) with N-donor ligands relevant for partitioning has been studied by time-resolved laser fluorescence spectroscopy (TRLFS). This work aims at a better understanding of the molecular reason of the selectivity of these ligands. In this context, enormous effort has been and is still put into detailed investigations on BTP and BTBP ligands, which are the most successful N-donor ligands for the selective extraction of trivalent actinides, to date. Additionally, the complexation and extraction behavior of molecules which are structurally related to these ligands is studied. The ligand C5-BPP (2,6-bis(5-(2,2-dimethylpropyl)-1H-pyrazol-3-yl)pyridine) where the triazine rings of the aromatic backbone of the BTP ligands have been replaced by pyrazole rings is one of these molecules. Laser fluorescence spectroscopic investigation of the complexation of Cm(III) with this ligand revealed stepwise formation of three (Cm(C5-BPP) n ) 3+ complexes (n = 1 - 3). The stability constant of the 1:3 complex was determined (log β 3 = 14.8 ± 0.4). Extraction experiments have shown that, in contrast to BTP and BTBP ligands, C5-BPP needs an additional lipophilic anion source such as a 2-bromocarboxylic acid to selectively extract trivalent actinides from nitric acid solutions. The comparison of the stability constant of the (Cm(C5-BPP) 3 ) 3+ complex with the stability constant of the (Cm(nPr-BTP) 3 ) 3+ complex

  12. Richard III

    DEFF Research Database (Denmark)

    Lauridsen, Palle Schantz

    2017-01-01

    Kort analyse af Shakespeares Richard III med fokus på, hvordan denne skurk fremstilles, så tilskuere (og læsere) langt henad vejen kan føle sympati med ham. Med paralleller til Netflix-serien "House of Cards"......Kort analyse af Shakespeares Richard III med fokus på, hvordan denne skurk fremstilles, så tilskuere (og læsere) langt henad vejen kan føle sympati med ham. Med paralleller til Netflix-serien "House of Cards"...

  13. Separation by liquid-liquid extraction of actinides(III) from lanthanides(III) using new molecules: the picolinamides; Separation par extraction liquide-liquide des actinides(III) des lanthanides(III) par de nouvelles molecules: les picolinamides

    Energy Technology Data Exchange (ETDEWEB)

    Cordier, P Y [CEA Marcoule, Departement de Recherche en Retraitement et en Vitrification, 30 - Bagnols-sur-Ceze (France); [Clermont-Ferrand-2 Univ., 63 - Aubiere (France)

    1996-07-01

    In the field of long-lived radionuclides separation from waste generated during spent fuel reprocessing, the picolinamides have been chosen as potential extractants for the selective extraction of actinides (III) from lanthanides (III). The first studies initiated on the most simple molecule of the picolinamide family, namely 2-pyridinecarboxamide, pointed out that in an aqueous media the complexation stability constant between this ligand and Am(III) is roughly 10 times higher than the ones corresponding to Ln(III). The synthesis of lipophilic derivatives of 2-pyridinecarboxamide leaded to extraction experiments. The extraction of metallic cation by lipophilic picolinamides, according to a solvatation mechanism, is strongly dependent on the nature of the amide function: a primary amide function (group I) leads to a good extraction; on the contrary, there is a decrease for secondary (group II) and tertiary (group III) amide functions. From a theoretical point of view, this work leads finally to the following conclusions: confirmation of the importance of the presence of soft donor atoms within the extractants (nitrogen in our case) for An(III)/Ln(III). Also, sensitivity of this soft donor atom regarding the protonation reaction; prevalence in our case of the affinity of the extractant for the metallic cation over the lipophilia of the extractant to ensure good distribution coefficients. The extraction and Am(III)/Ln(III) separation performances of the picolinamides from pertechnetic media leads to the design of a possible flowsheet for the reprocessing of high level liquid waste, with the new idea of an integrated technetium reflux. (author) 105 refs.

  14. Extraction behaviour of Am(III) and Eu(III) from nitric acid medium in TEHDGA-HDEHP impregnated resins

    Energy Technology Data Exchange (ETDEWEB)

    Saipriya, G.; Kumar, T. [Bhabha Atomic Research Centre Facilities, Kalpakkam (India). Kalpakkam Reprocessing Plant; Kumaresan, R.; Nayak, P.K.; Venkatesan, K.A.; Antony, M.P. [Indira Gandhi Center for Atomic Research, Kalpakkam (India). Fuel Chemistry Div.

    2016-07-01

    The extraction behaviour of Am(III) and Eu(III) from nitric acid medium was studied in the solvent impregnated resins containing extractants such as tetra-bis(2-ethylhexyl)diglycolamide (TEHDGA) or bis-(2-ethylhexyl)phosphoric acid (HDEHP) or mixture of TEHDGA+HDEHP. The rate of extraction of Am(III) and Eu(III) from 1 M nitric acid and the effect of various parameters, such as the concentration of nitric acid in aqueous phase and concentration of TEHDGA and HDEHP in resin phase, on the distribution coefficient of Am(III) and Eu(III) was studied. The distribution coefficient of Am(III) and Eu(III) in HDEHP-impregnated resin decreased and that in TEHDGA-impregnated resin increased, with increase in the concentration of nitric acid. However, in (TEHDGA+HDEHP) - impregnated resin, synergic extraction was observed at lower nitric acid concentration and antagonism at higher nitric acid concentration. The mechanism of Am(III) and Eu(III) extraction in the combined resin was investigated by slope analysis method. The extraction of various metal ions present in the fast reactor simulated high-level liquid waste was studied. The separation factor of Am(III) over Eu(III) was studied using citrate-buffered diethylenetriaminepentaacetic acid (DTPA) solution.

  15. Characterization of the lanthanum(III) and europium(III) trichloroacetate complexes extracted with 18-crown-6

    International Nuclear Information System (INIS)

    Imura, H.; Saito, Y.; Ohashi, K.; Meguro, Y.; Yoshida, Z.; Choppin, G.R.

    1996-01-01

    Extraction of lanthanide(III) ions with 18-crown-6 (18C6) and trichloroacetate (tca) has been studied. The composition, hydration, and structure of the La(III) and Eu(III) complexes extracted into 1,2-dichloroethane were investigated by using several methods such as the liquid-liquid distribution technique, conductimetry, Karl Fisher titration, laser luminescence spectroscopy, and 1 H NMR. The La(III) complex was found to be a monohydrate, La(tca) 3 (18C6)(H 2 O), while that of Eu(III) was a mixture of a monohydrate and a dihydrate, i.e., Eu(tca) 3 (18C6)(H 2 O) and Eu(tca) 3 (18C6)(H 2 O) 2 . The origin of the selectivity by 18C6 which gives much higher extractability of La(III) than of Eu(III) is explained by considering the hydration and probable structure of their complexes. 12 refs., 5 figs., 4 tabs

  16. Prospective trial of angiography and embolization for all grade III to V blunt splenic injuries: nonoperative management success rate is significantly improved.

    Science.gov (United States)

    Miller, Preston R; Chang, Michael C; Hoth, J Jason; Mowery, Nathan T; Hildreth, Amy N; Martin, R Shayn; Holmes, James H; Meredith, J Wayne; Requarth, Jay A

    2014-04-01

    Nonoperative management (NOM) of blunt splenic injury is well accepted. Substantial failure rates in higher injury grades remain common, with one large study reporting rates of 19.6%, 33.3%, and 75% for grades III, IV, and V, respectively. Retrospective data show angiography and embolization can increase salvage rates in these severe injuries. We developed a protocol requiring referral of all blunt splenic injuries, grades III to V, without indication for immediate operation for angiography and embolization. We hypothesized that angiography and embolization of high-grade blunt splenic injury would reduce NOM failure rates in this population. This was a prospective study at our Level I trauma center as part of a performance-improvement project. Demographics, injury characteristics, and outcomes were compared with historic controls. The protocol required all stable patients with grade III to V splenic injuries be referred for angiography and embolization. In historic controls, referral was based on surgeon preference. From January 1, 2010 to December 31, 2012, there were 168 patients with grades III to V spleen injuries admitted; NOM was undertaken in 113 (67%) patients. The protocol was followed in 97 patients, with a failure rate of 5%. Failure rate in the 16 protocol deviations was 25% (p = 0.02). Historic controls from January 1, 2007 to December 31, 2009 were compared with the protocol group. One hundred and fifty-three patients with grade III to V injuries were admitted during this period, 80 (52%) patients underwent attempted NOM. Failure rate was significantly higher than for the protocol group (15%, p = 0.04). Use of a protocol requiring angiography and embolization for all high-grade spleen injuries slated for NOM leads to a significantly decreased failure rate. We recommend angiography and embolization as an adjunct to NOM for all grade III to V splenic injuries. Copyright © 2014 American College of Surgeons. Published by Elsevier Inc. All rights reserved.

  17. A comparison of FEMAXI-III code calculations with irradiation experiments

    International Nuclear Information System (INIS)

    Ito, K.; Sogame, M.; Ichikawa, M.; Nakajima, T.

    1981-01-01

    The FEMAXI-III code calculations were compared with in-pile diameter measurements in the Halden Boiling Water Reactor, in order to check the ability to analyse the pellet-cladding mechanical interaction. The results showed generally good agreement between calculations and measurements. The Studsvik INTER-RAMP Experiments were also analysed to examine the predictability of fuel rod failures. Good agreement was obtained between calculated and measured fission gas x release. The threshold stress to cause failure was estimated by means of FEMAXI-III. (author)

  18. Purification of chicken carbonic anhydrase isozyme-III (CA-III) and its measurement in White Leghorn chickens.

    Science.gov (United States)

    Nishita, Toshiho; Tomita, Yuichiro; Yorifuji, Daisuke; Orito, Kensuke; Ochiai, Hideharu; Arishima, Kazuyosi

    2011-11-26

    The developmental profile of chicken carbonic anhydrase-III (CA-III) blood levels has not been previously determined or reported. We isolated CA-III from chicken muscle and investigated age-related changes in the levels of CA-III in blood. CA-III was purified from chicken muscle. The levels of CA-III in plasma and erythrocytes from 278 female chickens (aged 1-93 weeks) and 68 male chickens (aged 3-59 weeks) were determined by ELISA. The mean level of CA-III in female chicken erythrocytes (1 week old) was 4.6 μg/g of Hb, and the CA-III level did not change until 16 weeks of age. The level then increased until 63 weeks of age (11.8 μg/g of Hb), decreased to 4.7 μg/g of Hb at 73 weeks of age, and increased again until 93 weeks of age (8.6 μg/g of Hb). The mean level of CA-III in erythrocytes from male chickens (3 weeks old) was 2.4 μg/g of Hb, and this level remained steady until 59 weeks of age. The mean plasma level of CA-III in 1-week-old female chickens was 60 ng/mL, and this level was increased at 3 weeks of age (141 ng/mL) and then remained steady until 80 weeks of age (122 ng/mL). The mean plasma level of CA-III in 3-week-old male chickens was 58 ng/mL, and this level remained steady until 59 weeks of age. We observed both developmental changes and sex differences in CA-III concentrations in White Leghorn (WL) chicken erythrocytes and plasma. Simple linear regression analysis showed a significant association between the erythrocyte CA-III level and egg-laying rate in WL-chickens 16-63 weeks of age (p < 0.01).

  19. Thermodynamics of U(VI) and Eu(III) complexation by unsaturated carboxylates

    Energy Technology Data Exchange (ETDEWEB)

    Rawat, Neetika; Bhattacharyya, A. [Radiochemistry Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Tomar, B.S., E-mail: bstomar@barc.gov.in [Radiochemistry Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Ghanty, T.K. [Theoretical Chemistry Section, Bhabha Atomic Research Centre, Mumbai 400085 (India); Manchanda, V.K. [Radiochemistry Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

    2011-05-10

    Highlights: {yields} {Delta}H and log K determined for U(VI) and Eu(III) complexes with maleate and fumarate. {yields} log K and coordination environment of Eu(III) complexes has been studied by TRFS. {yields} Higher log K of U(VI) complexes than Eu(III) complexes is due to higher entropy. {yields} Plot of log K vs log K{sub P} suggest charge polarization in fumarate complexes. {yields} Ab initio calculations support charge polarization in fumarate complexes. - Abstract: The thermodynamic parameters ({Delta}G, {Delta}H and {Delta}S) of complexation of U(VI) and Eu(III) by unsaturated dicarboxylic acids, namely, maleic and fumaric acid, has been determined by potentiometric and microcalorimetric titrations at fixed ionic strength (I = 1.0 M) and temperature (298 K). The results show formation of 1:1 complexes by both the ligands with Eu(III). In the case of U(VI), maleate forms both 1:1 and 1:2 complexes, while only 1:1 complex was formed with fumarate. The fluorescence emission spectra of Eu(III)-dicarboxylate solutions at varying ligand to metal ratio were also used to obtain their stability constants. In addition, the fluorescence lifetimes reveal higher dehydration of Eu(III)-maleate compared to Eu(III)-fumarate which corroborates the {Delta}S values. The thermodynamic quantities suggest charge polarization effects in the case of U(VI) and Eu(III) complexes of fumarate, which is further corroborated by theoretical calculations. For the same ligand, U(VI) complexes were found to be more stable which was mainly due to higher entropy term.

  20. Extraction and stripping of neodymium (III) and dysprosium (III) by TRUEX solvent

    International Nuclear Information System (INIS)

    Rout, Alok; Venkatesan, K.A.; Antony, M.P.; Srinivasan, T.G.; Vasudeva Rao, P.R.

    2009-01-01

    McCabe-Thiele diagram for the extraction and stripping of Nd (III) and Dy (III) by TRUEX solvent has been constructed to determine the number of stages required for complete extraction and stripping. (author)

  1. Comparative trials in registration files of cardiovascular drugs : Comparator drugs and dosing schemes.

    NARCIS (Netherlands)

    Wieringa, NF; Vos, R; de Graeff, PA

    Registration files of 13 cardiovascular drugs were analysed with respect to the number of double-blind phase-III clinical trials, the use of placebo and active comparator drugs and their dosing schemes. Half of the 146 double-blind trials used active comparator drugs. The majority of files included

  2. Class III malocclusion with severe anteroposterior discrepancy

    Directory of Open Access Journals (Sweden)

    Susana Maria Deon Rizzatto

    2012-10-01

    Full Text Available This study aims at reporting the clinical case of a patient with Class III skeletal malocclusion with severe maxillary deficiency, producing a reduced midface associated with severe mandibular prognathism. The pre-surgical orthodontic preparation was composed mainly by dentoalveolar expansion and repositioning of the incisors in the lower arch. Then, a combined maxillary and mandibular orthognathic surgery was performed. The treatment objectives were achieved, with significant improvement in facial esthetics and occlusion, followed by post-treatment stability. This case was presented to the Brazilian Board of Orthodontics and Facial Orthopedics (BBO, as part of the requirements for obtaining the title of Diplomate by BBO.O objetivo deste artigo é relatar o caso clínico de um paciente portador de má oclusão de Classe III esquelética com acentuada deficiência maxilar, causando redução do terço médio da face, associada a severo prognatismo mandibular. O preparo ortodôntico pré-cirúrgico foi composto, principalmente, pela expansão dentoalveolar da maxila e o reposicionamento dos incisivos na arcada inferior. Depois, foi realizada a cirurgia ortognática combinada maxilomandibular. Os objetivos do tratamento foram atingidos, com significativa melhora da oclusão e da estética facial, seguida de estabilidade pós-tratamento. Esse caso foi apresentado à Diretoria do Board Brasileiro de Ortodontia e Ortopedia Facial (BBO, como parte dos requisitos para obtenção do título de Diplomado pelo BBO.

  3. The coupling of thermochemistry and phase diagrams for group III-V semiconductor systems. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, T.J.

    1998-07-21

    The project was directed at linking the thermochemical properties of III-V compound semiconductors systems with the reported phase diagrams. The solid-liquid phase equilibrium problem was formulated and three approaches to calculating the reduced standard state chemical potential were identified and values were calculated. In addition, thermochemical values for critical properties were measured using solid state electrochemical techniques. These values, along with the standard state chemical potentials and other available thermochemical and phase diagram data, were combined with a critical assessment of selected III-V systems. This work was culminated with a comprehensive assessment of all the III-V binary systems. A novel aspect of the experimental part of this project was the demonstration of the use of a liquid encapsulate to measure component activities by a solid state emf technique in liquid III-V systems that exhibit high vapor pressures at the measurement temperature.

  4. Broadcasting Stations of the World; Part III. Frequency Modulation Broadcasting Stations.

    Science.gov (United States)

    Foreign Broadcast Information Service, Washington, DC.

    This third part of "Broadcasting Stations of the World", which lists all reported radio broadcasting and television stations, with the exception of those in the United States which broadcast on domestic channels, covers frequency modulation broadcasting stations. It contains two sections: one indexed alphabetically by country and city, and the…

  5. Hydration structure of Ti(III) and Cr(III): Monte Carlo simulation ...

    African Journals Online (AJOL)

    Classical Monte Carlo simulations were performed to investigate the solvation structures of Ti(III) and Cr(III) ions in water with only ion-water pair interaction potential and by including three-body correction terms. The hydration structures were evaluated in terms of radial distribution functions, coordination numbers and ...

  6. Design study of a new vacuum vessel for Doublet III

    International Nuclear Information System (INIS)

    Rawls, J.M.; Davis, L.G.; Anderson, P.M.

    1980-10-01

    The principal thrust of the project was to examine a single design in enough depth to gain confidence in the feasibility and desirability of specific design features. However, a valuable spin-off of the project was to develop information of a more generic character to aid in future studies of possibilities for Doublet III. For example, we now feel that Doublet III can be reconfigured with any of a variety of new vacuum vessels, poloidal coil sets, and auxiliary heating systems within three years of project initiation, a period that is short compared to the time scale for developing a completely new facility. In addition, this can be accomplished at a fraction of the cost required to develop a comparable facility

  7. Má oclusão Classe III de Angle, subdivisão direita, tratada sem exodontias e com controle de crescimento Angle Class III malocclusion, subdivision right, treated without extractions and with growth control

    Directory of Open Access Journals (Sweden)

    Sérgio Henrique Casarim Fernandes

    2010-12-01

    Full Text Available A Classe III de Angle é uma má oclusão caracterizada por discrepâncias anteroposteriores dentárias e faciais, normalmente acompanhadas por alterações esqueléticas, com componente genético associado. O diagnóstico precoce e correto e o tratamento adequado são de suma importância para promover o controle do crescimento e evitar recidivas. Este artigo relata o tratamento, executado em duas fases, de uma paciente do sexo feminino de 12 anos de idade, apresentando uma má oclusão de Classe III de Angle, subdivisão direita, com mordida cruzada anterior em máxima intercuspidação habitual (MIH e topo em relação cêntrica (RC, apresentando, ainda, falta de espaço na maxila, que foi tratada sem exodontias e com controle de crescimento. Esse caso foi apresentado à Diretoria do Board Brasileiro de Ortodontia e Ortopedia Facial (BBO, representando a categoria 1, ou seja, uma má oclusão Classe III de Angle, tratada sem exodontias e com controle de crescimento, como parte dos requisitos para a obtenção do título de Diplomado pelo BBOAngle Class III malocclusion is characterized by anteroposterior dental and facial discrepancies usually accompanied by skeletal changes associated with a genetic component. Early, accurate diagnosis and appropriate treatment are of paramount importance to promote growth control and prevent relapse. This article reports the two-phase treatment of a female patient, aged 12 years, with an Angle Class III, subdivision right malocclusion with anterior crossbite in maximum intercuspation (MIC and end-on bite in centric relation, further presenting with lack of maxillary space. The case was treated without extractions and with growth control. This case was presented to the Brazilian Board of Orthodontics and Facial Orthopedics (BBO as representative of Category 1, i.e., Angle Class III malocclusion treated without tooth extractions, as part of the requirements for obtaining the BBO Diploma

  8. SEPARATION OF Fe (III, Cr(III, Cu(II, Ni(II, Co(II, AND Pb(II METAL IONS USING POLY(EUGENYL OXYACETIC ACID AS AN ION CARRIER BY A LIQUID MEMBRANE TRANSPORT METHOD

    Directory of Open Access Journals (Sweden)

    La Harimu

    2010-06-01

    Full Text Available Fe (III, Cr(III, Cu(II, Ni(II, Co(II, and Pb(II  metal ions had been separated using poly(eugenyl oxyacetic acid as an ion carrier by bulk liquid membrane transport method. The effect of pH, polyeugenyl oxyacetic acid ion carrier concentration, nitric acid concentration in the stripping solution, transport time, and metal concentration were optimized. The result showed that the optimum condition for transport of metal ions was at pH 4 for ion Fe(III and at pH 5 for Cr(III, Cu(II, Ni(II, Co(II, and Pb(II ions. The carrier volumes were optimum with concentration of 1 x 10-3 M at 7.5 mL for Cr(III, Cu (II,  Ni(II, Co(II ions and at 8.5 mL for Fe(III and Pb(II ions. The concentration of HNO3 in stripping phase was optimum at 2 M for Fe(III and Cu(II ions, 1 M for Cr(III, Ni(II and Co(II ions, and 0.5 M for Pb(II ion. The optimum transport times were 36 h for Fe(III and Co(II ions, and 48 h for Cr(III, Cu (II, Ni(II, and Pb(II ions. The concentration of metal ions accurately transported were 2.5 x 10-4 M for Fe(III and Cr(III ions, and 1 M for Cu (II, Ni(II, Co(II, and Pb(II ions. Compared to other metal ions the transport of Fe(III was the highest with selectivity order of Fe(III > Cr(III > Pb(II > Cu(II > Ni(II > Co(II. At optimum condition, Fe(III ion was transported through the membrane at 46.46%.   Keywords: poly(eugenyl oxyacetic acid, transport, liquid membrane, Fe (III, Cr(III, Cu(II, Ni(II, Co(II, and Pb(II ions

  9. Extraction Separation of Am(III) and Eu(III) with Thermo-sensitive Gel introducing TPEN Derivatives

    International Nuclear Information System (INIS)

    Kenji Takeshita; Yoshio Nakano; Tatsuro Matsumura; Atsunori Mori

    2008-01-01

    A thermal-swing chromatographic process using a thermo-sensitive gel co-polymerized with NIPA (N-isopropyl-acrylamide) and TPPEN (N,N,N',N'-tetrakis(4-propenyl-oxy-2-pyridyl-methyl)ethylenediamine) was studied for the separation of Am(III) from Eu(III). First, the radiolysis of the TPPEN-NIPA gel was tested by the γ-ray irradiation and the α nuclide adsorption. The extraction separation of Am(III) was not influenced in the radioactive environment of the proposed process. Next, the TPPEN-NIPA gel was immobilized in porous silica particles and the applicability of the gel-immobilized silica to the proposed process was tested. Am(III) was extracted selectively in the gel-immobilized silica at 5 deg. C and the separation factor of Am(III) over Eu(III) was evaluated to be 3.7. The distribution ratio of Am(III) was reduced to less than 1/20 by increasing temperature from 5 deg. C to 40 deg. C. These results indicate that the TPPEN-NIPA gel is applicable to the thermal-swing chromatographic process for the minor actinide recovery. (authors)

  10. Los Angeles International Airport Runway Incursion Studies: Phase III--Center-Taxiway Simulation

    Science.gov (United States)

    Madson, Michael D.

    2004-01-01

    Phase III of the Los Angeles International Airport Runway Incursion Studies was conducted, under an agreement with HNTB Corporation, at the NASA Ames FutureFlight Central (FFC) facility in June 2003. The objective of the study was the evaluation of a new center-taxiway concept at LAX. This study is an extension of the Phase I and Phase II studies previously conducted at FFC. This report presents results from Phase III of the study, in which a center-taxiway concept between runways 25L and 25R was simulated and evaluated. Phase III data were compared objectively against the Baseline data. Subjective evaluations by participating LAX controllers were obtained with regard to workload, efficiency, and safety criteria. To facilitate a valid comparison between Baseline and Phase III data, the same scenarios were used for Phase III that were tested during Phases I and II. This required briefing participating controllers on differences in airport and airline operations between 2001 and today.

  11. Additive Manufacturing: Which DLA-Managed Legacy Parts are Potential AM Candidates

    Science.gov (United States)

    2016-07-01

    R G ADDITIVE MANUFACTURING : WHICH DLA-MANAGED LEGACY PARTS ARE POTENTIAL AM CANDIDATES? REPORT DL501T1 J UL Y 2016...L Y 2 0 1 6 ADDITIVE MANUFACTURING : WHICH DLA-MANAGED LEGACY PARTS ARE POTENTIAL AM CANDIDATES? REPORT DL501T1 Thomas K . Pa rk s...DESIGNATED BY OTHER OFFICIAL DOCUMENTATION. LMI © 2016. ALL RIGHTS RESERVED. iii Additive Manufacturing : Which DLA-Managed Legacy Parts Are

  12. Field Surveys, IOC Valleys. Volume III, Part II. Cultural Resources Survey, Pine and Wah Wah Valleys, Utah.

    Science.gov (United States)

    1981-08-01

    including horse, camel, mammoth, Ertm E-TR-48-III-II 20 musk ox, and certain species of bison, goat, and bear, which had previously inhabited the marsh and...34 - - -9,$.. 𔄃 Im I I I Si to * Location lype/Contents Affiliation 42B@644 rid e over cr ek - P/J depression, cleared areas, Fr elon (f4-5-18-92) ground

  13. Three-Dimensional Evaluation of the Upper Airway Morphological Changes in Growing Patients with Skeletal Class III Malocclusion Treated by Protraction Headgear and Rapid Palatal Expansion: A Comparative Research.

    Directory of Open Access Journals (Sweden)

    Xueling Chen

    Full Text Available The aim of this study was to evaluate the morphological changes of upper airway after protraction headgear and rapid maxillary expansion (PE treatment in growing patients with Class III malocclusion and maxillary skeletal deficiency compared with untreated Class III patients by cone-beam computed tomography (CBCT.Thirty growing patients who have completed PE therapy were included in PE group. The control group (n = 30 was selected from the growing untreated patients with the same diagnosis. The CBCT scans of the pre-treatment (T1 and post-treatment (T2 of PE group and the control group were collected. Reconstruction and registration of the 3D models of T1 and T2 were completed. By comparing the data obtained from T1, T2 and control group, the morphological changes of the upper airway during the PE treatment were evaluated.Comparing with the data from T1 group, the subspinale (A of maxilla and the upper incisor (UI of the T2 group were moved in the anterior direction. The gnathion (Gn of mandible was moved in the posterior-inferior direction. The displacement of the hyoid bone as well as the length and width of dental arch showed significant difference. The volume and mean cross-sectional area of nasopharynx, velopharynx and glossopharynx region showed significant difference. The largest anteroposterior/the largest lateral (AP/LR ratios of the velopharynx and glossopharynx were increased, but the AP/LR ratio of the hypopharynx was decreased. In addition, the length and width of the maxillary dental arch, the displacement of the hyoid bone, the volume of nasopharynx and velopharynx, and the AP/LR ratio of the hypopharynx and velopharynx showed significant difference between the data from control and T2 group.The PE treatment of Class III malocclusion with maxillary skeletal hypoplasia leads to a significant increase in the volume of nasopharynx and velopharynx.

  14. Variation in plasmonic (electronic) spectral parameters of Pr (III) and Nd (III) with varied concentration of moderators

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, Shubha, E-mail: shubhamishra03@gmail.com [School of Studies in Physics, Vikram University, Ujjain (M. P.) (India); Limaye, S. N., E-mail: snl222@yahoo.co.in [Department of Chemistry, Dr. H.S. Gour University, A Central University, Sagar (M.P.) (India)

    2015-07-31

    It is said that the -4f shells behave as core and are least perturbed by changes around metal ion surrounding. However, there are evidences that-4f shells partially involved in direct moderator interaction. A systematic investigation on the plasmonic (electronic) spectral studies of some Rare Earths[RE(III).Mod] where, RE(III) = Pr(III),Nd(III) and Mod(moderator) = Y(III),La(III),Gd(III) and Lu(III), increased moderator concentration from 0.01 mol dm{sup −3} to 0.025 mol dm{sup −3} keeping the metal ion concentration at 0.01mol dm{sup −3} have been carried out. Variations in oscillator strengths (f), Judd-Ofelt parameters (T{sub λ}),inter-electronic repulsion Racah parameters (δE{sup k}),nephelauxetic ratio (β), radiative parameters (S{sub ED},A{sub T},β{sub R},T{sub R}). The values of oscillator strengths and Judd-Ofelt parameters have been discussed in the light of coordination number of RE(III) metal ions, denticity and basicity of the moderators. The [RE(III).Mod] bonding pattern has been studies in the light of the change in Racah parameters and nephelauxetic ratio.

  15. Purification of chicken carbonic anhydrase isozyme-III (CA-III and its measurement in White Leghorn chickens

    Directory of Open Access Journals (Sweden)

    Nishita Toshiho

    2011-11-01

    Full Text Available Abstract Background The developmental profile of chicken carbonic anhydrase-III (CA-III blood levels has not been previously determined or reported. We isolated CA-III from chicken muscle and investigated age-related changes in the levels of CA-III in blood. Methods CA-III was purified from chicken muscle. The levels of CA-III in plasma and erythrocytes from 278 female chickens (aged 1-93 weeks and 68 male chickens (aged 3-59 weeks were determined by ELISA. Results The mean level of CA-III in female chicken erythrocytes (1 week old was 4.6 μg/g of Hb, and the CA-III level did not change until 16 weeks of age. The level then increased until 63 weeks of age (11.8 μg/g of Hb, decreased to 4.7 μg/g of Hb at 73 weeks of age, and increased again until 93 weeks of age (8.6 μg/g of Hb. The mean level of CA-III in erythrocytes from male chickens (3 weeks old was 2.4 μg/g of Hb, and this level remained steady until 59 weeks of age. The mean plasma level of CA-III in 1-week-old female chickens was 60 ng/mL, and this level was increased at 3 weeks of age (141 ng/mL and then remained steady until 80 weeks of age (122 ng/mL. The mean plasma level of CA-III in 3-week-old male chickens was 58 ng/mL, and this level remained steady until 59 weeks of age. Conclusion We observed both developmental changes and sex differences in CA-III concentrations in White Leghorn (WL chicken erythrocytes and plasma. Simple linear regression analysis showed a significant association between the erythrocyte CA-III level and egg-laying rate in WL-chickens 16-63 weeks of age (p

  16. N-butylamine functionalized graphene oxide for detection of iron(III) by photoluminescence quenching.

    Science.gov (United States)

    Gholami, Javad; Manteghian, Mehrdad; Badiei, Alireza; Ueda, Hiroshi; Javanbakht, Mehran

    2016-02-01

    An N-butylamine functionalized graphene oxide nanolayer was synthesized and characterized by ultraviolet (UV)-visible spectrometry, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy. Detection of iron(III) based on photoluminescence spectroscopy was investigated. The N-butylamine functionalized graphene oxide was shown to specifically interact with iron (III), compared with other cationic trace elements including potassium (I), sodium (I), calcium (II), chromium (III), zinc (II), cobalt (II), copper (II), magnesium (II), manganese (II), and molybdenum (VI). The quenching effect of iron (III) on the luminescence emission of N-butylamine functionalized graphene oxide layer was used to detect iron (III). The limit of detection (2.8 × 10(-6)  M) and limit of quantitation (2.9 × 10(-5)  M) were obtained under optimal conditions. Copyright © 2015 John Wiley & Sons, Ltd.

  17. 21 CFR 316.1 - Scope of this part.

    Science.gov (United States)

    2010-04-01

    ... drugs for rare diseases or conditions, including biological products and antibiotics. This part sets... for investigations of drugs for rare diseases or conditions; (ii) Requests for designation of a drug for a rare disease or condition; and (iii) Requests for gaining exclusive approval for a drug product...

  18. Demonstration of a III-nitride vertical-cavity surface-emitting laser with a III-nitride tunnel junction intracavity contact

    International Nuclear Information System (INIS)

    Leonard, J. T.; Young, E. C.; Yonkee, B. P.; Cohen, D. A.; Margalith, T.; Speck, J. S.; DenBaars, S. P.; Nakamura, S.

    2015-01-01

    We report on a III-nitride vertical-cavity surface-emitting laser (VCSEL) with a III-nitride tunnel junction (TJ) intracavity contact. The violet nonpolar VCSEL employing the TJ is compared to an equivalent VCSEL with a tin-doped indium oxide (ITO) intracavity contact. The TJ VCSEL shows a threshold current density (J th ) of ∼3.5 kA/cm 2 , compared to the ITO VCSEL J th of 8 kA/cm 2 . The differential efficiency of the TJ VCSEL is also observed to be significantly higher than that of the ITO VCSEL, reaching a peak power of ∼550 μW, compared to ∼80 μW for the ITO VCSEL. Both VCSELs display filamentary lasing in the current aperture, which we believe to be predominantly a result of local variations in contact resistance, which may induce local variations in refractive index and free carrier absorption. Beyond the analyses of the lasing characteristics, we discuss the molecular-beam epitaxy (MBE) regrowth of the TJ, as well as its unexpected performance based on band-diagram simulations. Furthermore, we investigate the intrinsic advantages of using a TJ intracavity contact in a VCSEL using a 1D mode profile analysis to approximate the threshold modal gain and general loss contributions in the TJ and ITO VCSEL

  19. Demonstration of a III-nitride vertical-cavity surface-emitting laser with a III-nitride tunnel junction intracavity contact

    Energy Technology Data Exchange (ETDEWEB)

    Leonard, J. T., E-mail: jtleona01@gmail.com; Young, E. C.; Yonkee, B. P.; Cohen, D. A.; Margalith, T.; Speck, J. S. [Materials Department, University of California, Santa Barbara, California 93106 (United States); DenBaars, S. P.; Nakamura, S. [Materials Department, University of California, Santa Barbara, California 93106 (United States); Department of Electrical and Computer Engineering, University of California, Santa Barbara, California 93106 (United States)

    2015-08-31

    We report on a III-nitride vertical-cavity surface-emitting laser (VCSEL) with a III-nitride tunnel junction (TJ) intracavity contact. The violet nonpolar VCSEL employing the TJ is compared to an equivalent VCSEL with a tin-doped indium oxide (ITO) intracavity contact. The TJ VCSEL shows a threshold current density (J{sub th}) of ∼3.5 kA/cm{sup 2}, compared to the ITO VCSEL J{sub th} of 8 kA/cm{sup 2}. The differential efficiency of the TJ VCSEL is also observed to be significantly higher than that of the ITO VCSEL, reaching a peak power of ∼550 μW, compared to ∼80 μW for the ITO VCSEL. Both VCSELs display filamentary lasing in the current aperture, which we believe to be predominantly a result of local variations in contact resistance, which may induce local variations in refractive index and free carrier absorption. Beyond the analyses of the lasing characteristics, we discuss the molecular-beam epitaxy (MBE) regrowth of the TJ, as well as its unexpected performance based on band-diagram simulations. Furthermore, we investigate the intrinsic advantages of using a TJ intracavity contact in a VCSEL using a 1D mode profile analysis to approximate the threshold modal gain and general loss contributions in the TJ and ITO VCSEL.

  20. The settlement Cernavoda III culture on the site Bubanj near Niš

    Directory of Open Access Journals (Sweden)

    Milanović Dragan

    2011-01-01

    Full Text Available Archaeological investigations carried out between 2008 and 2010 in the east sector of site Bubanj near Niš (Plan 1; Figs. 1-3 confirmed the existence of horizon of the Cernavoda III culture. In features 22, 23 and 31, which are the remains of settlement buildings, have been found archaeological material mostly pottery vessels, which according to style of decoration, technological and morphological characteristics could be ascribed to the initial period of late Eneolithic. Also, the dwelling structures of Krivodol-Salcuþa-Bubanj cultural complex have been recorded in the layer of brown soil with the remains of above mentioned Cernavoda III buildings. In the vertical stratigraphy of trench I (Fig. 4 the mentioned layer was encountered immediately under the layer of whitish/gray ashy soil and thin layer of compact soil of gray color (Fig. 5, which date from the advanced phases of the late Eneolithic and above the early Eneolithic layers. The settlement features recorded during 2009 excavations are parts of the structures from the settlement of Cernavoda III culture (Fig. 6; T. I-III. Feature 22 is section of devastated probably aboveground building, feature 23 is shallow pit and feature 31 is most probably the rubbish pit. Very similar stratigraphy of the site had been recorded by investigations of M. Garašanin in 1954. In the layer of brown soil, the material of Cernavoda III culture was discovered in level III, and in level IV both Cernavoda III and the material of the earlier Krivodol-Salcuþa-Bubanj cultural complex was recorded. These building horizons are at different depths within approximately same area of the trench and have been identified on the basis of considerable amount of daub and stone, two floor levels, wooden building material and fragmented pottery vessels (T. IV-VI. Despite the lack of technical field documentation remains of one above ground structure could be identified at level III according to descriptions from field

  1. SIMMER-III code-verification. Phase 1

    International Nuclear Information System (INIS)

    Maschek, W.

    1996-05-01

    SIMMER-III is a computer code to investigate core disruptive accidents in liquid metal fast reactors but should also be used to investigate safety related problems in other types of advanced reactors. The code is developed by PNC with cooperation of the European partners FZK, CEA and AEA-T. SIMMER-III is a two-dimensional, three-velocity-field, multiphase, multicomponent, Eulerian, fluid-dynamics code coupled with a space-, time-, and energy-dependent neutron dynamics model. In order to model complex flow situations in a postulated disrupting core, mass and energy conservation equations are solved for 27 density components and 16 energy components, respectively. Three velocity fields (two liquid and one vapor) are modeled to simulate the relative motion of different fluid components. An additional static field takes into account the structures available in a reactor (pins, hexans, vessel structures, internal structures etc.). The neutronics is based on the discrete ordinate method (S N method) coupled into a quasistatic dynamic model. The code assessment and verification of the fluid dynamic/thermohydraulic parts of the code is performed in several steps in a joint effort of all partners. The results of the FZK contributions to the first assessment and verification phase is reported. (orig.) [de

  2. Rapid identification of Enterobacter hormaechei and Enterobacter cloacae genetic cluster III.

    Science.gov (United States)

    Ohad, S; Block, C; Kravitz, V; Farber, A; Pilo, S; Breuer, R; Rorman, E

    2014-05-01

    Enterobacter cloacae complex bacteria are of both clinical and environmental importance. Phenotypic methods are unable to distinguish between some of the species in this complex, which often renders their identification incomplete. The goal of this study was to develop molecular assays to identify Enterobacter hormaechei and Ent. cloacae genetic cluster III which are relatively frequently encountered in clinical material. The molecular assays developed in this study are qPCR technology based and served to identify both Ent. hormaechei and Ent. cloacae genetic cluster III. qPCR results were compared to hsp60 sequence analysis. Most clinical isolates were assigned to Ent. hormaechei subsp. steigerwaltii and Ent. cloacae genetic cluster III. The latter was proportionately more frequently isolated from bloodstream infections than from other material (P < 0·05). The qPCR assays detecting Ent. hormaechei and Ent. cloacae genetic cluster III demonstrated high sensitivity and specificity. The presented qPCR assays allow accurate and rapid identification of clinical isolates of the Ent. cloacae complex. The improved identifications obtained can specifically assist analysis of Ent. hormaechei and Ent. cloacae genetic cluster III in nosocomial outbreaks and can promote rapid environmental monitoring. An association was observed between Ent. cloacae cluster III and systemic infection that deserves further attention. © 2014 The Society for Applied Microbiology.

  3. Morphometric Analysis of the Mandible in Subjects with Class III Malocclusion

    Directory of Open Access Journals (Sweden)

    Jin-Yun Pan

    2006-07-01

    Full Text Available This study evaluated the deformations that contribute to Class III mandibular configuration, employing geometric morphometric analysis. Lateral cephalograms of male and female groups of 100 young adults and 70 children with Class III malocclusion were compared to those of counterparts with normal occlusion. The sample included an equal number of both genders. The cephalographs were traced, and 12 homologous landmarks were identified and digitized. Average mandibular geometries were generated by means of Procrustes analysis. Thin-plate spline analysis was then applied to mandibular configurations to determine local form differences in male and female groups of adults and children with normal occlusion and Class III malocclusion. The mandibular morphology was significantly different between these two groups of male and female adults, and children (p < 0.0001. This spline analysis revealed an anteroposterior elongation of the mandible along the condylion-gnathion axis, showing an extension in the regions of the mandibular condyle and ramus, and of the anteroinferior portion of the mandibular symphysis in Class III groups. More extension was evident in Class III adults. The deformations in subjects with Class III malocclusion may represent a developmental elongation of the mandible anteroposteriorly, which leads to the appearance of a prognathic mandibular profile.

  4. Eleventh annual meeting, Bologna, Italy, 17-20 April 1978. Summary report. Part I

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-06-01

    The Summary Report of the Eleventh Annual Meeting of the IAEA International Working Group on Fast Reactors contains the Minutes of the Meeting (Part I); the papers which review the national programmes in the field of LMFBRs and other presentations at the Meeting (Part II); and the discussions on the review of the national programmes (Part III)

  5. Recent operational history of the new Sandia Pulsed Reactor III (SPR III)

    International Nuclear Information System (INIS)

    Schmidt, T.R.; Estes, B.F.; Reuscher, J.A.

    1977-01-01

    The Sandia Pulsed Reactor III (SPR III) is a fast-pulse research reactor which was designed and built at Sandia Laboratories and achieved criticality in August 1975. The reactor is now characterized and is in an operational configuration. The core consists of 18 fuel plates (258 kg fuel mass) of fully enriched uranium alloyed with 10 wt.% molybdenum. It is arranged in an annular configuration with an inside diameter of 17.78 cm, an outside diameter of 29.72 cm, and a height of 35.9 cm. The reactor core uses reflectors of copper and aluminum for control and an external bolting arrangement to secure the fuel plates. SPR III and SPR II are operated on an interchangeable basis using the same facility and control system. As of June 1977, SPR III has had over 240 operations with core temperatures up to 541 0 C

  6. Characterization of ribonuclease III from Brucella.

    Science.gov (United States)

    Wu, Chang-Xian; Xu, Xian-Jin; Zheng, Ke; Liu, Fang; Yang, Xu-Dong; Chen, Chuang-Fu; Chen, Huan-Chun; Liu, Zheng-Fei

    2016-04-01

    Bacterial ribonuclease III (RNase III) is a highly conserved endonuclease, which plays pivotal roles in RNA maturation and decay pathways by cleaving double-stranded structure of RNAs. Here we cloned rncS gene from the genomic DNA of Brucella melitensis, and analyzed the cleavage properties of RNase III from Brucella. We identified Brucella-encoding small RNA (sRNA) by high-throughput sequencing and northern blot, and found that sRNA of Brucella and Homo miRNA precursor (pre-miRNA) can be bound and cleaved by B.melitensis ribonuclease III (Bm-RNase III). Cleavage activity of Bm-RNase III is bivalent metal cations- and alkaline buffer-dependent. We constructed several point mutations in Bm-RNase III, whose cleavage activity indicated that the 133th Glutamic acid residue was required for catalytic activity. Western blot revealed that Bm-RNase III was differently expressed in Brucella virulence strain 027 and vaccine strain M5-90. Collectively, our data suggest that Brucella RNase III can efficiently bind and cleave stem-loop structure of small RNA, and might participate in regulation of virulence in Brucella. Copyright © 2016 Elsevier B.V. All rights reserved.

  7. Limiting Factors for Microbial Fe(III)-Reduction In a Landfill Leachate Polluted Aquifer (Vejen, Denmark)

    DEFF Research Database (Denmark)

    Albrechtsen, Hans-Jørgen; Heron, Gorm; Christensen, Thomas Højlund

    1995-01-01

    Aquifer sediment samples from two locations within the anaerobic leachate plume of a municipal landfill were compared with respect to microbiology (especially Fe(III)-reduction) and geochemistry. The samples close to the landfill were characterized by low contents of Fe(III), whereas samples from...... the more distant cluster were rich in Fe(III)-oxides. The active microbial population seemed to be less dense in samples more distant from the landfill (measured by ATP and phospholipid fatty acids (PLFA)), but the microbial communities were very similar in the two sample clusters according...... to the composition of PLFA. Very little, if any, Fe(III)-reduction was observed close to the landfill, but all the more distant samples showed evident microbially mediated Fe(III)-reduction. After amendment with both acetate and Fe(III), all the samples showed a potential for Fe(III)-reduction, and the in situ Fe...

  8. Fosfato de cromo (III marcado con diferentes radionúclidos para uso en radiosinoviortesis Chromium (III phosphate labelled with several radionuclides for use in radiosynoviothersis

    Directory of Open Access Journals (Sweden)

    Jorge Cruz Arencibia

    2012-06-01

    Full Text Available Introducción: la radiosinoviortesis se utiliza en el tratamiento de la sinovitis crónica, complicación frecuente en enfermedades sistémicas como artritis reumatoide y hemofilia. En la práctica clínica internacional se emplean diferentes coloides y suspensiones radiactivas, pero su número es reducido y su disponibilidad limitada. Objetivo: obtención y caracterización físico-química de suspensiones de fosfato de cromo (III marcadas con radionúclidos como potenciales radiofármacos para uso en radiosinoviortesis. Métodos: las suspensiones se obtuvieron por síntesis química, los radionúclidos se añadieron al inicio de la reacción o después de finalizada esta. El tamaño de partículas se estimó mediante microscopia óptica y filtración por membranas. Asimismo se evaluó por espectrofotometría la estabilidad de la suspensión al ser resuspendida en distintos medios. La pureza radioquímica se determinó por cromatografía de papel. Resultados: se obtuvo y caracterizó una suspensión de fosfato de cromo (III. El producto obtenido presentó un tamaño de partículas predominante entre 0,8-5 µm y que al ser suspendidas en solución de gelatina al 2 % en tampón acetato 1 mg/mL no sedimentó en menos de 3 h. Se estableció la tecnología para la obtención de formulaciones de fosfato de cromo (III marcado con 32P e 90Y y se demostró la factibilidad de marcar la suspensión obtenida con otros radionúclidos trivalentes como 177Lu y 68Ga. Conclusiones: los resultados permiten considerar al fosfato de cromo (III una suspensión base para la obtención de radiofármacos para uso en radiosinoviortesis en diferentes articulaciones, en función de las características físico-nucleares de los radionúclidos que se empleen.Introduction: radiosynoviorthesis is used in treating chronic synovitis, a frequent complication of some systemic diseases as rheumatoid arthritis and hemophilia. There are different colloids and radioactive

  9. Metalloporphyrin Co(III)TMPyP ameliorates acute, sublethal cyanide toxicity in mice.

    Science.gov (United States)

    Benz, Oscar S; Yuan, Quan; Amoscato, Andrew A; Pearce, Linda L; Peterson, Jim

    2012-12-17

    The formation of Co(III)TMPyP(CN)(2) at pH 7.4 has been shown to be completely cooperative (α(H) = 2) with an association constant of 2.1 (±0.2) × 10(11). The kinetics were investigated by stopped-flow spectrophotometry and revealed a complicated net reaction exhibiting 4 phases at pH 7.4 under conditions where cyanide was in excess. The data suggest molecular HCN (rather than CN(-)) to be the attacking nucleophile around neutrality. The two slower phases do not seem to be present when cyanide is not in excess, and the other two phases have rates comparable to that observed for cobalamin, a known effective cyanide scavenger. Addition of bovine serum albumin (BSA) did not affect the cooperativity of cyanide binding to Co(III)TMPyP, only lowered the equilibrium constant slightly to 1.2 (±0.2) × 10(11) and had an insignificant effect on the observed rate. A sublethal mouse model was used to assess the effectiveness of Co(III)TMPyP as a potential cyanide antidote. The administration of Co(III)TMPyP to sodium cyanide intoxicated mice resulted in the time required for the surviving mice to right themselves from a supine position being significantly decreased (9 ± 2 min) compared to that of the controls (33 ± 2 min). All observations were consistent with the demonstrated antidotal activity of Co(III)TMPyP operating through a cyanide-binding (i.e., scavenging) mechanism.

  10. Antithrombin III blood test

    Science.gov (United States)

    ... medlineplus.gov/ency/article/003661.htm Antithrombin III blood test To use the sharing features on this page, ... a protein that helps control blood clotting. A blood test can determine the amount of AT III present ...

  11. ESCRT-III mediated cell division in Sulfolobus acidocaldarius –A reconstitution perspective

    Directory of Open Access Journals (Sweden)

    Tobias eHärtel

    2014-06-01

    Full Text Available In the framework of Synthetic Biology, it has become an intriguing question what would be the minimal representation of cell division machinery. Thus, it seems appropriate to compare how cell division is realized in different microorganisms. In particular, the cell division system of Crenarchaeota lacks certain proteins found in most bacteria and Euryarchaeota, such as FtsZ, MreB or the Min system. The Sulfolobaceae family encodes functional homologs of the eukaryotic proteins Vps4 and ESCRT-III. ESCRT-III is essential for several eukaryotic pathways, e.g. budding of intralumenal vesicles (ILVs, or cytokinesis, whereas Vps4 dissociates the ESCRT-III complex from the membrane. CdvA (Cell Division A is required for the recruitment of crenarchaeal ESCRT-III proteins to the membrane at mid-cell. The proteins polymerize and form a smaller structure during constriction. Thus, ESCRT-III mediated cell division in S. acidocaldarius shows functional analogies to the Z ring observed in prokaryotes like E. coli, which has recently begun to be reconstituted in vitro. In this short perspective, we discuss the possibility of building such an in vitro cell division system on basis of archaeal ESCRT-III.

  12. WRKY domain-encoding genes of a crop legume chickpea (Cicer arietinum): comparative analysis with Medicago truncatula WRKY family and characterization of group-III gene(s).

    Science.gov (United States)

    Kumar, Kamal; Srivastava, Vikas; Purayannur, Savithri; Kaladhar, V Chandra; Cheruvu, Purnima Jaiswal; Verma, Praveen Kumar

    2016-06-01

    The WRKY genes have been identified as important transcriptional modulators predominantly during the environmental stresses, but they also play critical role at various stages of plant life cycle. We report the identification of WRKY domain (WD)-encoding genes from galegoid clade legumes chickpea (Cicer arietinum L.) and barrel medic (Medicago truncatula). In total, 78 and 98 WD-encoding genes were found in chickpea and barrel medic, respectively. Comparative analysis suggests the presence of both conserved and unique WRKYs, and expansion of WRKY family in M. truncatula primarily by tandem duplication. Exclusively found in galegoid legumes, CaWRKY16 and its orthologues encode for a novel protein having a transmembrane and partial Exo70 domains flanking a group-III WD. Genomic region of galegoids, having CaWRKY16, is more dynamic when compared with millettioids. In onion cells, fused CaWRKY16-EYFP showed punctate fluorescent signals in cytoplasm. The chickpea WRKY group-III genes were further characterized for their transcript level modulation during pathogenic stress and treatments of abscisic acid, jasmonic acid, and salicylic acid (SA) by real-time PCR. Differential regulation of genes was observed during Ascochyta rabiei infection and SA treatment. Characterization of A. rabiei and SA inducible gene CaWRKY50 showed that it localizes to plant nucleus, binds to W-box, and have a C-terminal transactivation domain. Overexpression of CaWRKY50 in tobacco plants resulted in early flowering and senescence. The in-depth comparative account presented here for two legume WRKY genes will be of great utility in hastening functional characterization of crop legume WRKYs and will also help in characterization of Exo70Js. © The Author 2016. Published by Oxford University Press on behalf of Kazusa DNA Research Institute.

  13. Investigation of Emerging Materials for Optoelectronic Devices Based on III-Nitrides

    KAUST Repository

    Muhammed, Mufasila Mumthaz

    2018-03-11

    III-nitride direct bandgap semiconductors have attracted significant research interest due to their outstanding potential for modern optoelectronic and electronic applications. However, the high cost of III-nitride devices, along with low performance due to dislocation defects, remains an obstacle to their further improvement. In this dissertation, I present a significant enhancement of III-nitride devices based on emerging materials. A promising substrate, (-201)-oriented β-Ga2O3 with unique properties that combine high transparency and conductivity, is used for the first time in the development of high-quality vertical III-nitride devices, which can be cost-effective for large-scale production. In addition, hybridizing GaN with emerging materials, mainly perovskite, is shown to extend the functionality of III-nitride applications. As a part of this investigation, high-performance and high-responsivity fast perovskite/GaN-based UV-visible broadband photodetectors were developed. State-of-the-art GaN epilayers grown on (-201)-oriented β-Ga2O3 using AlN and GaN buffer layers are discussed, and their high optical quality without using growth enhancement techniques is demonstrated. In particular, a low lattice mismatch (⁓4.7%) between GaN and the substrate results in a low density of dislocations ~4.8Å~107 cm−2. To demonstrates the effect of (-201)-oriented β-Ga2O3 substrate on the quality of III-nitride alloys, high-quality ternary alloy InxGa1−xN film is studied, followed by the growth of high quality InxGa1−xN/GaN single and multiple quantum wells (QWs). The optical characterization and carrier dynamics by photoluminescence (PL) and time-resolved PL measurements were subsequently performed. Lastly, to investigate the performance of a vertical emitting device based on InGaN/GaN multiple QWs grown on (-201)-oriented β-Ga2O3 substrate, high-efficiency vertical-injection emitting device is developed and extensively investigated. The conductive nature of

  14. Measurement of L sub(III) subshell fluorescence yields in Pb, Th and U

    Energy Technology Data Exchange (ETDEWEB)

    Arora, S K; Allawadhi, K L; Sood, B S [Punjabi Univ., Patiala (India). Nuclear Science Labs.

    1981-01-01

    L sub(III) subshell fluorescence yields in Pb, Th and U have been measured using photoionization for creating vacancies. The results have been compared with the available data and are found to agree with the recent measurements of Price made using K-L coincidence technique but higher than those of Stephenson made using fluorescent excitation of L sub(III) subshell.

  15. Type I and III procollagen propeptides in growth hormone-deficient patients

    DEFF Research Database (Denmark)

    Jensen, L T; Jørgensen, J O; Risteli, J

    1991-01-01

    The effect of increasing doses of growth hormone on collagen synthesis in GH-treated GH-deficient patients was determined in a short-term study. The synthesis of type I and III collagen was estimated by measurements of the carboxyterminal propeptide of type I procollagen and the aminoterminal...... propeptide of type III procollagen. Type I collagen is mainly found in bone and type III collagen in loose connective tissue. We observed a GH dose dependency of both procollagen propeptides. Serum type I procollagen propeptide was significantly higher following GH doses of 4 and 6 IU/day for 14 days...... procollagen propeptide increased twice as much as type I procollagen propeptide, by 47 vs 25%, at a GH dose of 6 IU/day compared with 2 IU/day. The differences between the effects on type I and type III collagen may reflect differences in secretion or turn-over rate of collagen in bone and loose connective...

  16. Demographics and Outcomes of Stage I-II Merkel Cell Carcinoma Treated with Mohs Micrographic Surgery Compared with Wide Local Excision in the National Cancer Data Base.

    Science.gov (United States)

    Singh, Babu; Qureshi, Muhammad M; Truong, Minh Tam; Sahni, Debjani

    2018-02-03

    The optimal surgical approach (wide local excision (WLE) vs. Mohs micrographic surgery (MOHS)) for treating Merkel cell carcinoma (MCC) is yet to be determined. To compare survival outcomes in patients with early stage MCC treated with MOHS versus WLE. A retrospective review of all cases in the National Cancer Data Base (NCDB) of MCC of clinical Stage I-II MCC treated with WLE or MOHS was performed. 1,795 cases of Stage I-II MCC were identified who underwent WLE (N=1,685) or MOHS (N=110). There was no difference in residual tumor on surgical margins between the two treatment groups (p=0.588). On multivariate analysis, there was no difference in overall survival between the treatment modalities (adjusted HR 1.02; 95% CI 0.72-1.45, p=0.897). There was no difference in overall survival between the two groups on propensity score matched analysis. Disease specific survival was not reported as this data in not available in the NCDB. MOHS appears to be as effective as WLE in treating early stage MCC. Copyright © 2018. Published by Elsevier Inc.

  17. Liquid plugs bouncing against a solid basis, comparison of SIMMER-III and PLEXUS results; Zum Aufprall von Fluessigkeitssaeulen auf starre Hindernisse Vergleich von SIMMER-III und PLEXUS Ergebnissen

    Energy Technology Data Exchange (ETDEWEB)

    Maschek, W.; Arnecke, G.; Flad, M.

    1995-08-01

    The SIMMER III code is being tested by application to problems of reactor accidents. The fluid dynamics/thermohydraulics part of the code can be applied also to evaporation/condensation, melt, and freezing phenomena. For a liquid plug bouncing against a solid basis, the momentum transfer is calculated. PLEXUS results turn out to be in significant disagreement with the SIMMER calculations. (orig.)

  18. [Cell-ELA-based determination of binding affinity of DNA aptamer against U87-EGFRvIII cell].

    Science.gov (United States)

    Tan, Yan; Liang, Huiyu; Wu, Xidong; Gao, Yubo; Zhang, Xingmei

    2013-05-01

    A15, a DNA aptamer with binding specificity for U87 glioma cells stably overexpressing the epidermal growth factor receptor variant III (U87-EGFRvIII), was generated by cell systematic evolution of ligands by exponential enrichment (cell-SELEX) using a random nucleotide library. Subsequently, we established a cell enzyme-linked assay (cell-ELA) to detect the affinity of A15 compared to an EGFR antibody. We used A15 as a detection probe and cultured U87-EGFRvIII cells as targets. Our data indicate that the equilibrium dissociation constants (K(d)) for A15 were below 100 nmol/L and had similar affinity compared to an EGFR antibody for U87-EGFRvIII. We demonstrated that the cell-ELA was a useful method to determine the equilibrium dissociation constants (K(d)) of aptamers generated by cell-SELEX.

  19. Examining Data Processing Work as Part of the Scientific Data Lifecycle Comparing Practices Across Four Scientific Research Groups

    OpenAIRE

    Paine, Drew; Lee, Charlotte

    2015-01-01

    Slides from Charlotte P. Lee's presentation at the 2015 iConference on our paper "Examining Data Processing Work as Part of the Scientific Data Lifecycle: Comparing Practices Across Four Scientific Research Groups".

  20. Performance on the Wechsler Adult Intelligence Scale-III in Japanese patients with schizophrenia.

    Science.gov (United States)

    Fujino, Haruo; Sumiyoshi, Chika; Sumiyoshi, Tomiki; Yasuda, Yuka; Yamamori, Hidenaga; Ohi, Kazutaka; Fujimoto, Michiko; Umeda-Yano, Satomi; Higuchi, Arisa; Hibi, Yumiko; Matsuura, Yukako; Hashimoto, Ryota; Takeda, Masatoshi; Imura, Osamu

    2014-07-01

    Patients with schizophrenia have been reported to perform worse than non-schizophrenic populations on neuropsychological tests, which may be affected by cultural factors. The aim of this study was to examine the performance of a sizable number of patients with schizophrenia on the Japanese version of the Wechsler Adult Intelligence Scale-III (WAIS-III) compared with healthy controls. Performance on the WAIS-III was evaluated in 157 Japanese patients with schizophrenia and in 264 healthy control subjects. All IQ scores and four indices from the WAIS-III were impaired for patients with schizophrenia compared with healthy controls. Processing Speed was markedly disturbed, approximately 2 SD below that of the healthy control group. Among the 13 subtests, Comprehension (z = -1.70, d = 1.55), Digit Symbol Coding (z = -1.84, d = 1.88), and Symbol Search (z = -1.85, d = 1.77) were profoundly impaired relative to the healthy controls. These results indicate that the pattern and degree of impairment, as evaluated by the WAIS-III, in Japanese patients are similar to those previously reported in English-speaking patients and that the deficits of some neuropsychological domains relevant to functional outcomes are universally characteristic of schizophrenia. © 2014 The Authors. Psychiatry and Clinical Neurosciences © 2014 Japanese Society of Psychiatry and Neurology.

  1. Duration of the pubertal peak in skeletal Class I and Class III subjects.

    Science.gov (United States)

    Kuc-Michalska, Małgorzata; Baccetti, Tiziano

    2010-01-01

    To estimate and compare the duration of the pubertal growth peak in Class I and Class III subjects. The data examined consisted of pretreatment lateral cephalometric records of 218 skeletal Class I or Class III subjects (93 female and 125 male subjects) of white ancestry. The duration of the pubertal peak was calculated from the average chronological age intervals between stages CS3 and CS4 of the cervical vertebral maturation in Class I vs Class III groups (t-test). In skeletal Class I subjects, the pubertal peak had a mean duration of 11 months, whereas in Class III subjects it lasted 16 months. The average difference (5 months) was statistically significant (P < .001). The growth interval corresponding to the pubertal growth spurt (CS3-CS4) was longer in Class III subjects than in subjects with normal skeletal relationships; the larger increases in mandibular length during the pubertal peak reported in the literature for Class III subjects may be related to the longer duration of the pubertal peak.

  2. A study of Class III treatment: orthodontic camouflage vs orthognathic surgery.

    Science.gov (United States)

    Georgalis, Katherine; Woods, Michael G

    2015-11-01

    To evaluate the differences in pretreatment and post-treatment characteristics of Class III patients treated with orthodontic camouflage or orthognathic surgery, and to compare the range of skeletal, dental and soft tissue changes that are likely to occur with treatment, with particular reference to the influence of extractions on the resultant incisor angulations. Pretreatment and post-treatment cephalograms of 31 Class III orthodontically-camouflaged patients and 36 Class III surgical patients (without genioplasty) were obtained from one specialist practice. From the surgical group, 26 pre-surgical lateral cephalograms were also obtained. Inclusion criteria for the two groups were at least three of the following: (1) an ANB angle of 1 degree or less, (2) a Wits appraisal less than -4 mm, (3) an incisal overjet ≤ 0 mm, and (14) a Class III molar relationship. All lateral cephalograms were traced and digitised and a number of skeletal, dental and soft tissue variables were measured. The camouflage and surgical groups were also divided into premolar extraction and non-extraction subgroups to allow for a specific analysis of extraction effects. Before treatment, the surgical group demonstrated, on average, a more severe skeletal discrepancy and increased dental compensations, compared with the orthodontically camouflaged group. After treatment, the mean SNA angle was greater, the ANB angle was more positive, the Wits appraisal was closer to ideal and the lower incisors were less retroclined in the surgery group. There was a small mean reduction in horizontal chin projection in the surgery group compared with a small increase in the camouflage group. The mentolabial fold and the lower lip curve were deeper, on average, and the lips less retrusive after surgery. There was a mean increase in upper incisor proclination during treatment in both the surgical and camouflage groups with a greater increase in the camouflage group. There was a significant reduction in upper

  3. Investigation of the separation of americium(III) and europium(III) by high-speed countercurrent chromatography

    International Nuclear Information System (INIS)

    Wu, J.F.; Jin, Y.R.; Xu, Q.C.; Wang, S.L.; Zhang, L.X.

    2005-01-01

    The long-lived actinides are the important elements in the radioactive waste ;disposal. Because the ions semi diameter and chemical properties of trivalent actinides(III) and trivalent lanthanides(III) are very similar, the separation between them is very difficult. Yang Yu-Sheng put forward the actinides(III) are softer acid than the lanthanides(III), so the actinides(III) are more easily extracted by the soft extractant contain sulfur or nitrogen than the lanthanides(III). Some research have been done on the separation between actinides(III) and lanthanides(III) using the extractants contain sulfur or nitrogen. The results show that satisfactory separation efficiency was gained. Countercurrent Chromatography (CCC) have many specific advantages, such as free from solid support, permit large sample volume and high flow rate, which is useful in the preconcentration of inorganic solute and inorganic preparation. Some studies were done on the separation of lanthanides or-other inorganic elements by HSCCC, the high-purity reagents prepared by HSCCC or CPC turned out to be successful. In present paper, the investigation of separation between Americium (III) and Euricium (III) by High-Speed Countercurrent Chromatography (HSCCC) were made. The extractant used in the work was prepared by ourselves, which is of the soft extractant contrain sulfur. The effects of separation condition on the separation efficiency of Am and Eu by HSCCC were investigated using dichlorophenyl dithiophosphinic acid in xylene as the stationary phase and 0.1 mol/L NaClO4 as mobile phase, respectively. The results show that mutual separation between Am and Eu can be accomplished. The separation factor increases with the increasing of the concentration of extractant and the pH value of the mobile phase, further more, minishing the flow rate of the mobile phase can also improves the separation efficiency between Am and Eu. The nearly base separation was gained when the flow rate is 0.35 ml/min, the

  4. Effect of pH on stability constants of Am(III)- and Cm(III)- humate complexes

    International Nuclear Information System (INIS)

    Samadfam, Mohammad; Jintoku, Takashi; Sato, Seichi; Ohashi, Hiroshi; Mitsugashira, Toshiaki; Hara, Mitsuo; Suzuki, Yoshimitsu

    1999-01-01

    The apparent stability constants of Am(III)- and Cm(III)-humate complexes were determined by dialysis method at ionic strength 0.1 in the pH range from 3.3 to 5.7 under N 2 bubbling. The Am(III) and Cm(III) loadings were about 10 -7 and 10 -10 mol/dm 3 . The concentrations of Am-241 and Cm-242 tracers were measured by α-spectrometry. It was found that the apparent stability constants were almost identical for both the Am(III)-humate and Cm(III)-humate complexes. The apparent stability constants showed a small pH-dependence, increasing from 10 4.6 at pH 3.3 to 10 5.1 at pH 5.7. The ionization of acidic functional groups of humic acid is possibly the primary factor. Above pH 6, the dialysis membrane was no langer permeable to Am(III) and Cm(III) ions and the apparent stability constant could not be experimentally obtained. The apparent stability constants between pH 6 and pH 8.5 were evaluated by considering that both binary metal-humate and ternary metal-hydroxo-humate complexes exist at pHs above 6. It was assumed that mono-hydroxo-humate complex Am(OH)HA and Cm(OH)HA are the major ternary complexes that exist below pH 9. The overall stability constants for Am(III)- and Cm(III)-humate complexes increased from 10 5.7 at pH 6 to 10 7.2 at pH 8. This implies that the formation of metal-hydroxo-humate species is preferred over the formation of hydroxide species. The apparent overall stability constants can be easily incorporated into geochemical modeling of trivalent actinide migration. The results of the present study show that the apparent stability constants determined experimentally at pH≤6 do not represent the complexation properties at higher pHs and the formation of ternary complexes should be considered in speciation calculations of radionuclides at terrestrial environment. (J.P.N.)

  5. Not-for-profit versus for-profit health care providers-Part I: comparing and contrasting their records.

    Science.gov (United States)

    Rotarius, Timothy; Trujillo, Antonio J; Liberman, Aaron; Ramirez, Bernardo

    2005-01-01

    The debate over which health care providers are most capably meeting their responsibilities in serving the public's interest continues unabated, and the comparisons of not-for-profit (NFP) versus for-profit (FP) hospitals remain at the epicenter of the discussion. From the perspective of available factual information, which of the two sides to this debate is correct? This article is part I of a 2-part series on comparing and contrasting the performance records of NFP health care providers with their FP counterparts. Although it is demonstrated that both NFP and FP providers perform virtuous and selfless feats on behalf of America's public, it is also shown that both camps are involved in potentially willful clinical and administrative missteps. Part I contains the background information (eg, legal differences, perspectives on social responsibility, and types of questionable and fraudulent behavior) that is necessary to adequately understand the scope of the comparison issue. Part II offers actual comparisons of the 2 organizational structures using several disparate factors such as specific organizational behaviors, approach to the health care priorities of cost and quality, and business-focused goals of profits, efficiency, and community benefit.

  6. Not-for-profit versus for-profit health care providers--Part II: Comparing and contrasting their records.

    Science.gov (United States)

    Rotarius, Timothy; Trujillo, Antonio J; Liberman, Aaron; Ramirez, Bernardo

    2006-01-01

    The debate over which health care providers are most capably meeting their responsibilities in serving the public's interest continues unabated, and the comparisons of not-for-profit (NFP) versus for-profit (FP) hospitals remain at the epicenter of the discussion. From the perspective of available factual information, which of the two sides to this debate is correct? This article is part II of a 2-part series on comparing and contrasting the performance records of NFP health care providers with their FP counterparts. Although it is demonstrated that both NFP and FP providers perform virtuous and selfless feats on behalf of America's public, it is also shown that both camps have been accused of being involved in potentially willful clinical and administrative missteps. Part I provided the background information (eg, legal differences, perspectives on social responsibility, and types of questionable and fraudulent behavior) required to adequately understand the scope of the comparison issue. Part II offers actual comparisons of the 2 organizational structures using several disparate factors such as specific organizational behaviors, approach to the health care priorities of cost and quality, and business-focused goals of profits, efficiency, and community benefit.

  7. Rise, fall and resurrection of chromosome territories: a historical perspective. Part II. Fall and resurrection of chromosome territories during the 1950s to 1980s. Part III. Chromosome territories and the functional nuclear architecture: experiments and models from the 1990s to the present.

    Science.gov (United States)

    Cremer, T; Cremer, C

    2006-01-01

    Part II of this historical review on the progress of nuclear architecture studies points out why the original hypothesis of chromosome territories from Carl Rabl and Theodor Boveri (described in part I) was abandoned during the 1950s and finally proven by compelling evidence forwarded by laser-uv-microbeam studies and in situ hybridization experiments. Part II also includes a section on the development of advanced light microscopic techniques breaking the classical Abbe limit written for readers with little knowledge about the present state of the theory of light microscopic resolution. These developments have made it possible to perform 3D distance measurements between genes or other specifically stained, nuclear structures with high precision at the nanometer scale. Moreover, it has become possible to record full images from fluorescent structures and perform quantitative measurements of their shapes and volumes at a level of resolution that until recently could only be achieved by electron microscopy. In part III we review the development of experiments and models of nuclear architecture since the 1990s. Emphasis is laid on the still strongly conflicting views about the basic principles of higher order chromatin organization. A concluding section explains what needs to be done to resolve these conflicts and to come closer to the final goal of all studies of the nuclear architecture, namely to understand the implications of nuclear architecture for nuclear functions.

  8. Air quality and climate change, Topic 3 of the Model Inter-Comparison Study for Asia Phase III (MICS-Asia IIIPart 1: Overview and model evaluation

    Directory of Open Access Journals (Sweden)

    M. Gao

    2018-04-01

    Full Text Available Topic 3 of the Model Inter-Comparison Study for Asia (MICS-Asia Phase III examines how online coupled air quality models perform in simulating high aerosol pollution in the North China Plain region during wintertime haze events and evaluates the importance of aerosol radiative and microphysical feedbacks. A comprehensive overview of the MICS-Asia III Topic 3 study design, including descriptions of participating models and model inputs, the experimental designs, and results of model evaluation, are presented. Six modeling groups from China, Korea and the United States submitted results from seven applications of online coupled chemistry–meteorology models. Results are compared to meteorology and air quality measurements, including data from the Campaign on Atmospheric Aerosol Research Network of China (CARE-China and the Acid Deposition Monitoring Network in East Asia (EANET. The correlation coefficients between the multi-model ensemble mean and the CARE-China observed near-surface air pollutants range from 0.51 to 0.94 (0.51 for ozone and 0.94 for PM2.5 for January 2010. However, large discrepancies exist between simulated aerosol chemical compositions from different models. The coefficient of variation (SD divided by the mean can reach above 1.3 for sulfate in Beijing and above 1.6 for nitrate and organic aerosols in coastal regions, indicating that these compositions are less consistent from different models. During clean periods, simulated aerosol optical depths (AODs from different models are similar, but peak values differ during severe haze events, which can be explained by the differences in simulated inorganic aerosol concentrations and the hygroscopic growth efficiency (affected by varied relative humidity. These differences in composition and AOD suggest that future models can be improved by including new heterogeneous or aqueous pathways for sulfate and nitrate formation under hazy conditions, a secondary organic aerosol (SOA

  9. Self-assembled Targeting of Cancer Cells by Iron(III)-doped, Silica Nanoparticles

    OpenAIRE

    Mitchell, K.K. Pohaku; Sandoval, S.; Cortes-Mateos, M. J.; Alfaro, J.G.; Kummel, A. C.; Trogler, W.C.

    2014-01-01

    Iron(III)-doped silica nanoshells are shown to possess an in vitro cell-receptor mediated targeting functionality for endocytosis. Compared to plain silica nanoparticles, iron enriched ones are shown to be target-specific, a property that makes them potentially better vehicles for applications, such as drug delivery and tumor imaging, by making them more selective and thereby reducing the nanoparticle dose. Iron(III) in the nanoshells can interact with endogenous transferrin, a serum protein ...

  10. Crown-root morphology of lower incisors in patients with class III malocclusion.

    Science.gov (United States)

    Wang, Bo; Shen, Guofang; Fang, Bing; Zhang, Li

    2012-07-01

    The purpose of this study was to investigate the crown-root morphology of lower incisors in patients with class III malocclusion using cone-beam computed tomography. Cone-beam computed tomography images were analyzed from 53 adult class I patients (group 1), 37 preadolescent class III patients (group 2), and 66 adult class III patients (group 3) comprising 3 divisions (divisions 1, 2, and 3 corresponded to mild, moderate, and severe class III malocclusions). The size and crown-root angulations of lower incisors in different groups and divisions were statistically appraised with group 1 used as the control group. No significant differences were found for the size of lower incisors among different groups and divisions (P > 0.05). Compared with group 1, the crown-root angulations of lower incisors in groups 2 and 3 were significantly larger (P lower incisors of division 3 rather than divisions 2 and 3 exhibited larger crown-root angulations (P lower incisors in class III patients during orthodontic and orthognathic treatment, especially in severe ones.

  11. Significant reduction of normal tissue dose by proton radiotherapy compared with three-dimensional conformal or intensity-modulated radiation therapy in Stage I or Stage III non-small-cell lung cancer

    International Nuclear Information System (INIS)

    Chang, Joe Y.; Zhang Xiaodong; Wang Xiaochun; Kang Yixiu; Riley, Beverly C.; Bilton, Stephen C.; Mohan, Radhe; Komaki, Ritsuko; Cox, James D.

    2006-01-01

    Purpose: To compare dose-volume histograms (DVH) in patients with non-small-cell lung cancer (NSCLC) treated by photon or proton radiotherapy. Methods and Materials: Dose-volume histograms were compared between photon, including three-dimensional conformal radiation therapy (3D-CRT), intensity-modulated radiation therapy (IMRT), and proton plans at doses of 66 Gy, 87.5 Gy in Stage I (n = 10) and 60-63 Gy, and 74 Gy in Stage III (n 15). Results: For Stage I, the mean total lung V5, V10, and V20 were 31.8%, 24.6%, and 15.8%, respectively, for photon 3D-CRT with 66 Gy, whereas they were 13.4%, 12.3%, and 10.9%, respectively, with proton with dose escalation to 87.5 cobalt Gray equivalents (CGE) (p = 0.002). For Stage III, the mean total lung V5, V10, and V20 were 54.1%, 46.9%, and 34.8%, respectively, for photon 3D-CRT with 63 Gy, whereas they were 39.7%, 36.6%, and 31.6%, respectively, for proton with dose escalation to 74 CGE (p = 0.002). In all cases, the doses to lung, spinal cord, heart, esophagus, and integral dose were lower with proton therapy even compared with IMRT. Conclusions: Proton treatment appears to reduce dose to normal tissues significantly, even with dose escalation, compared with standard-dose photon therapy, either 3D-CRT or IMRT

  12. Interaction between La(III) and proteins on the plasma membrane of horseradish

    Science.gov (United States)

    Yang, Guang-Mei; Chu, Yun-Xia; Lv, Xiao-Fen; Zhou, Qing; Huang, Xiao-Hua

    2012-06-01

    Lanthanum (La) is an important rare earth element in the ecological environment of plant. The proteins on the plasma membrane control the transport of molecules into and out of cell. It is very important to investigate the effect of La(III) on the proteins on the plasma membrane in the plant cell. In the present work, the interaction between La(III) and proteins on the plasma membrane of horseradish was investigated using optimization of the fluorescence microscopy and fluorescence spectroscopy. It is found that the fluorescence of the complex system of protoplasts and 1-aniline Kenai-8-sulfonic acid in horseradish treated with the low concentration of La(III) is increased compared with that of the control horseradish. The opposite effect is observed in horseradish treated with the high concentration of La(III). These results indicated that the low concentration of La(III) can interact with the proteins on the plasma membrane of horseradish, causing the improvement in the structure of proteins on the plasma membrane. The high concentration of La(III) can also interact with the proteins on the plasma membrane of horseradish, leading to the destruction of the structure of proteins on the plasma membrane. We demonstrate that the proteins on the plasma membrane are the targets of La(III) action on plant cell.

  13. Planning and conducting meetings effectively, part I: planning a meeting.

    Science.gov (United States)

    Harolds, Jay

    2011-12-01

    Meetings are held by leaders for many purposes, including conveying information, raising morale, asking for opinions, brain storming, making people part of the problem-solving process, building trust, getting to a consensus, and making decisions. However, many meetings waste time, some undermine the leader's power, and some decrease morale. Part I of this series of articles gives some tips on basic planning for decision-making meetings. Part II of this series of articles analyzes selected components of decision-making meetings. Part III of this series will be on how the chairperson keeps decision-making meetings on track to make them efficient and productive.

  14. Trends in heteroepitaxy of III-Vs on silicon for photonic and photovoltaic applications

    Science.gov (United States)

    Lourdudoss, Sebastian; Junesand, Carl; Kataria, Himanshu; Metaferia, Wondwosen; Omanakuttan, Giriprasanth; Sun, Yan-Ting; Wang, Zhechao; Olsson, Fredrik

    2017-02-01

    We present and compare the existing methods of heteroepitaxy of III-Vs on silicon and their trends. We focus on the epitaxial lateral overgrowth (ELOG) method as a means of achieving good quality III-Vs on silicon. Initially conducted primarily by near-equilibrium epitaxial methods such as liquid phase epitaxy and hydride vapour phase epitaxy, nowadays ELOG is being carried out even by non-equilibrium methods such as metal organic vapour phase epitaxy. In the ELOG method, the intermediate defective seed and the mask layers still exist between the laterally grown purer III-V layer and silicon. In a modified ELOG method called corrugated epitaxial lateral overgrowth (CELOG) method, it is possible to obtain direct interface between the III-V layer and silicon. In this presentation we exemplify some recent results obtained by these techniques. We assess the potentials of these methods along with the other existing methods for realizing truly monolithic photonic integration on silicon and III-V/Si heterojunction solar cells.

  15. A randomized phase III trial comparing concomitant chemoradiotherapy versus radiotherapy alone in advanced head and neck cancers - mature results: Yoodhvir Singh Nagar, Lucknow Cancer Institute, India

    International Nuclear Information System (INIS)

    Singh, S.; Kumar, S.; Datta, N.R.

    2003-01-01

    To evaluate contribution of concomitant chemoradiotherapy (CTRT) over and above radiotherapy alone (RT) in previously untreated stage III/IV, squamous cell carcinoma of the head and neck (SCCH and N). Patients with cancers of oral cavity (OC), oropharynx (OP), supraglottis (SG) and hypopharynx (HP) were randomized into RT arm or CTRT arm. Radiotherapy was identical in both arms (70Gy/35 fractions/7 weeks). In CTRT arm concomitant cisplatin (35mg/m 2 ) was given weekly for seven cycles. Surgery was reserved for salvage purposes when required. From May 1996 to December 1998, 155 patients (RT=78, CTRT=77) were enrolled and 139 patients (RT1,CTRT=68) were assessable. Over 90% patients in both arms completed planned treatment. The complete response rate was 51% in RT arm and 71% in CTRT arm (p=0.017). The median disease free survival (DFS) and overall survival (OS) in RT arm and CTRT arm were 3 months vs. 11 months (p=0.0009) and 9 months vs. 26 months (p=0.01) respectively. The 5-year DFS and OS in the two arms were 10% vs. 27% (p=0.000) and 16% vs. 29% (p=0.01) respectively. Acute grade III toxicity was comparable in both the arms (12% vs. 16%, p=0.74). Late grade I/II toxicity was higher in CTRT arm (70% vs. 51%, p=0.09). Serious late toxicities were not seen in both arms. On univariate analysis the favorable factors for immediate response were protocol (CTRT better), primary site (SG and OP better than OC and HP), T-stage (T1-T2 better), Nodes (N0 better than N+), Stage (III > IV), KPS (>80) and lesser overall treatment time (OTT). Multivariate analysis retained protocol, T stage, N stage and OTT as factors independently affecting the immediate response. Addition of concomitant weekly cisplatin (35mg/m 2 ) to radiotherapy improves the likelihood of local control, DFS and OS with acceptable acute and late toxicities and can be recommended as a standard form of treatment in advanced SCCH and N

  16. Tenth annual meeting, Vienna, Austria, 29 March - 1 April 1977. Summary report. Part I

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-05-01

    The Summary Report of Tenth Annual Meeting of the IAEA International Working Group on Fast Reactors contains the Minutes of the Meeting (Part I); the papers which review the national programmes in the field of LMFBRs and other presentations at the Meeting (Part II); and the discussions on the review of the national programmes (Part III)

  17. Part III: Comparing observed growth of selected test organisms in food irradiation studies with growth predictions calculated by ComBase softwares

    International Nuclear Information System (INIS)

    Farkas, J.; Andrassy, E.; Meszaros, L.; Beczner, J.; Polyak-Feher, K.; Gaal, O.; Lebovics, V.K.; Lugasi, A.

    2009-01-01

    As a result of intensive predictive microbiological modelling activities, several computer programs and softwares became available recently for facilitating microbiological risk assessment. Among these tools, the establishment of the ComBase, an international database and its predictive modelling softwares of the Pathogen Modelling Program (PMP) set up by the USDA Eastern Regional Research Center, Wyndmore, PA, and the Food Micromodel/Growth Predictor by the United Kingdom's Institute of Food Research, Norwich, are most important. The authors have used the PMP 6.1 software version of ComBase as a preliminary trial to compare observed growth of selected test organisms in relation to their food irradiation work during recent years within the FAO/IAEA Coordinated Food Irradiation Research Projects (D6.10.23 and D6.20.07) with the predicted growth on the basis of growth models available in ComBase for the same species as those of the authors' test organisms. The results of challenge tests with Listeria monocytogenes inoculum in untreated or irradiated experimental batches of semi-prepared breaded turkey meat steaks (cordon bleu), sliced tomato, sliced watermelon, sliced cantaloupe and sous vide processed mixed vegetables, as well as Staphylococcus aureus inoculum of a pasta product, tortellini, were compared with their respective growth models under relevant environmental conditions. This comparison showed good fits in the case of non-irradiated and high moisture food samples, but growth of radiation survivors lagged behind the predicted values. (author)

  18. Heterobimetallic gadolinium(III)-iron(III) complex of DTPA-bis(3-hydroxytyramide)

    International Nuclear Information System (INIS)

    Parac-Vogt, Tatjana N.; Kimpe, Kristof; Binnemans, Koen

    2004-01-01

    A derivative of diethylenetriamine-N,N,N',N'',N''-pentaacetic acid (DTPA), carrying two catechol functional groups has been synthesised by the reaction between DTPA-bis(anhydride) and 3-hydroxytyramine (dopamine). The ligand DTPA-bis(3-hydroxytyramide), [DTPA(HTA) 2 ], is able to form stable heterobimetallic complexes with gadolinium(III) and iron(III) ions. The gadolinium(III) occupies the internal coordination cage of DTPA formed by three nitrogens, two carboxylate and two amide oxygens, while the [Fe(NTA)(H 2 O) 2 ] (nitrilotriacetic acid, NTA) binds to catechol units by the substitution of two water ligands. The formation of polymeric species was avoided by using the tripodal NTA ligand. The heterobimetallic complex was characterised by means of visible absorption spectroscopy, electron spray ionisation-mass spectrometry (ESI-MS), and nuclear magnetic resonance (NMR) spectroscopy

  19. Separation of yttrium (III) from lanthanoids (III) by solvent extraction with substituted N-Alkylcarbonyl-N-phenylhydroxylamines

    International Nuclear Information System (INIS)

    Haraguchi, K.; Ogata, T.; Nakagawa, K.; Saitoh, T.; Kamidate, T.; Watanabe, H.

    1996-01-01

    A series of substituted N-alkylcarbonyl-N-phenylhydroxylamines(R-PHAs) were synthesized and utilized for the extraction of yttrium(III) and lanthanoids(III) in order to obtain effective extractants for the separation of yttrium(III) from the lanthanoids(III) and the mutual separation of the lanthanoids(III). The distribution ratio of yttrium(III) and the lanthanoids(III) between the carbon tetrachloride and the aqueous phases was measured as functions of the pH and the extractant concentration at 298 K at an ionic strength of 0.1 (NaNO 3 ). Yttrium(III) and the lanthanoids(III) were extracted with R-PHAs(HL) as self-adducted chelates of the form, ML 3 (HL) x , where 'x' is 1, 2 or 3 depending on the extraction system. The extractability of the metal ions decreased in the order of R-PHA having a primary, a secondary and a tertiary alkyl substituent attached to the carbonyl group because of the steric hindrance of the alkyl group. The separation factors for both Yb/Eu and Yb/Y pairs increased with increasing branching of the alkyl group of R-PHA. The excellent selectivity of R-PHAs having a tertiary alkyl group was attributable to a greater inductive effect of the tertiary alkyl group than those of the primary and secondary alkyl groups. The substituents at the phenyl group of R-PHAs gave no significant effect on the selectivity, while the extractability was enhanced considerably by introduction of electron withdrawing substituents at appropriate positions of the phenyl group of R-PHAs. (authors)

  20. Separation by liquid-liquid extraction of actinides(III) from lanthanides(III) using new molecules: the picolinamides

    International Nuclear Information System (INIS)

    Cordier, P.Y.

    1996-07-01

    In the field of long-lived radionuclides separation from waste generated during spent fuel reprocessing, the picolinamides have been chosen as potential extractants for the selective extraction of actinides (III) from lanthanides (III). The first studies initiated on the most simple molecule of the picolinamide family, namely 2-pyridinecarboxamide, pointed out that in an aqueous media the complexation stability constant between this ligand and Am(III) is roughly 10 times higher than the ones corresponding to Ln(III). The synthesis of lipophilic derivatives of 2-pyridinecarboxamide leaded to extraction experiments. The extraction of metallic cation by lipophilic picolinamides, according to a solvatation mechanism, is strongly dependent on the nature of the amide function: a primary amide function (group I) leads to a good extraction; on the contrary, there is a decrease for secondary (group II) and tertiary (group III) amide functions. From a theoretical point of view, this work leads finally to the following conclusions: confirmation of the importance of the presence of soft donor atoms within the extractants (nitrogen in our case) for An(III)/Ln(III). Also, sensitivity of this soft donor atom regarding the protonation reaction; prevalence in our case of the affinity of the extractant for the metallic cation over the lipophilia of the extractant to ensure good distribution coefficients. The extraction and Am(III)/Ln(III) separation performances of the picolinamides from pertechnetic media leads to the design of a possible flowsheet for the reprocessing of high level liquid waste, with the new idea of an integrated technetium reflux. (author)

  1. The triple-axis neutron spectrometer KANDI III and measurement of phonons in copper

    International Nuclear Information System (INIS)

    Melamud, M.; Pinto, H.; Shaked, H.

    1976-12-01

    The acoustic phonon dispersion relations of copper were measured using the recently installed triple-axis neutron spectrometer KANDI III. A description of KANDI III and its peripherals is given in this work. The theory of dispersion relations and their measurement using neutron inelastic diffraction are briefly discussed. Raw data and results for copper are presented and compared with the data and results found in the literature

  2. Note: Comparison of grazing incidence small angle x-ray scattering of a titania sponge structure at the beamlines BW4 (DORIS III) and P03 (PETRA III)

    International Nuclear Information System (INIS)

    Rawolle, M.; Körstgens, V.; Ruderer, M. A.; Metwalli, E.; Guo, S.; Müller-Buschbaum, P.; Herzog, G.; Benecke, G.; Schwartzkopf, M.; Buffet, A.; Perlich, J.; Roth, S. V.

    2012-01-01

    Grazing incidence small angle x-ray scattering (GISAXS) is a powerful technique for morphology investigation of nanostructured thin films. GISAXS measurements at the newly installed P03 beamline at the storage ring PETRA III in Hamburg, Germany, are compared to the GISAXS data from the beamline BW4 at the storage ring DORIS III, which had been used extensively for GISAXS investigations in the past. As an example, a titania thin film sponge structure is investigated. Compared to BW4, at beamline P03 the resolution of larger structures is slightly improved and a higher incident flux leads to a factor of 750 in scattered intensity. Therefore, the acquisition time in GISAXS geometry is reduced significantly at beamline P03.

  3. Validation of the Addenbrooke's Cognitive Examination III in frontotemporal dementia and Alzheimer's disease.

    Science.gov (United States)

    Hsieh, Sharpley; Schubert, Samantha; Hoon, Christopher; Mioshi, Eneida; Hodges, John R

    2013-01-01

    The aims of this study were to validate the newly developed version of the Addenbrooke's Cognitive Examination (ACE-III) against standardised neuropsychological tests and its predecessor (ACE-R) in early dementia. A total of 61 patients with dementia (frontotemporal dementia, FTD, n = 33, and Alzheimer's disease, AD, n = 28) and 25 controls were included in the study. ACE-III cognitive domains correlated significantly with standardised neuropsychological tests used in the assessment of attention, language, verbal memory and visuospatial function. The ACE-III also compared very favourably with its predecessor, the ACE-R, with similar levels of sensitivity and specificity. The results of this study provide objective validation of the ACE-III as a screening tool for cognitive deficits in FTD and AD. © 2013 S. Karger AG, Basel.

  4. The implementation and application of the WASP-III at CNEN/Brazil

    International Nuclear Information System (INIS)

    Sakamoto, L.H.; Lima, J.O.V.; Silva, R.C.O. da.

    1983-09-01

    The main dificulties faced in the implementation of the WASP-III on the Honeywell Bull DPS 6/64 computer at CNEN, are discribed. After the implementation, tests making use of input data provided by International Atomic Energy Agency - IAEA were performed and comparative results from accomplishment peiods of time are presented with the basic characteristics of the computer employed and the modifications carried out to adapt the programm. The WASP-III was applied to middle-sized electric system based upon the Brazilian North/Northeast System. (Author) [pt

  5. Removal of arsenic from water using manganese (III) oxide: Adsorption of As(III) and As(V).

    Science.gov (United States)

    Babaeivelni, Kamel; Khodadoust, Amid P

    2016-01-01

    Removal of arsenic from water was evaluated with manganese (III) oxide (Mn2O3) as adsorbent. Adsorption of As(III) and As(V) onto Mn2O3 was favorable according to the Langmuir and Freundlich adsorption equilibrium equations, while chemisorption of arsenic occurred according to the Dubinin-Radushkevich equation. Adsorption parameters from the Langmuir, Freundlich, and Temkin equations showed a greater adsorption and removal of As(III) than As(V) by Mn2O3. Maximum removal of As(III) and As(V) occurred at pH 3-9 and at pH 2, respectively, while removal of As(V) in the pH range of 6-9 was 93% (pH 6) to 61% (pH 9) of the maximum removal. Zeta potential measurements for Mn2O3 in As(III) was likely converted to As(V) solutions indicated that As(III) was likely converted to As(V) on the Mn2O3 surface at pH 3-9. Overall, the effective Mn2O3 sorbent rapidly removed As(III) and As(V) from water in the pH range of 6-9 for natural waters.

  6. Workshop 95. Part III

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    Out of 140 short communications presented in the proceedings, 13 have been inputted into INIS. The topics covered include lifetime control in semiconductor devices by ion irradiation, single crystal scintillation detectors, environmental monitoring, diffusion and sorption of radionuclides in soils, accelerator driven reactors, radioactive waste disposal, digital reactor control systems and research reactors. (Z.S.).

  7. Workshop 95. Part III

    International Nuclear Information System (INIS)

    1995-01-01

    Out of 140 short communications presented in the proceedings, 13 have been inputted into INIS. The topics covered include lifetime control in semiconductor devices by ion irradiation, single crystal scintillation detectors, environmental monitoring, diffusion and sorption of radionuclides in soils, accelerator driven reactors, radioactive waste disposal, digital reactor control systems and research reactors. (Z.S.)

  8. MicroVent (part III)

    DEFF Research Database (Denmark)

    Dreau, Jerome Le; Heiselberg, Per Kvols; Jensen, Rasmus Lund

    This study aims at using the InVentilate unit in the cooling case, without heat recovery. It results in a relatively low inlet air temperature. Different solutions have been tested to decrease the risk of draught in the occupied zone: ‐ Using a mixer (2 designs) ‐ Using an inlet grille ‐ Using...

  9. Craniofacial changes in Class III malocclusion as related to skeletal and dental maturation.

    Science.gov (United States)

    Baccetti, Tiziano; Reyes, Brian C; McNamara, James A

    2007-08-01

    In this large cross-sectional study, we aimed to analyze growth trends in white subjects with Class III malocclusion using both skeletal and dental maturation staging. The sample consisted of 1091 pretreatment lateral cephalometric records of Class III patients (560 female, 531 male). Cephalometric dentoskeletal measurements were compared at subsequent stages in cervical vertebral maturation and Hellman's categorization of dental development by means of ANOVA with Bonferroni post-hoc tests in both sexes separately. The findings indicated that, in Class III malocclusion, the pubertal peak in mandibular growth occurs between stages 3 and 4 of cervical vertebral maturation, with average increases in total mandibular length of about 8 and 5.5 mm in Class III boys and girls, respectively. Significant changes in total mandibular length occur until young adulthood (18 years on average), with increases between late maturation stages (4 through 6) that were twice as large as in subjects with normal occlusion for the Class III females, and 3 times as large as in subjects with normal occlusion for the Class III males. Growth trends toward accentuated Class III profile and increased vertical dimension of the face also become apparent at late developmental stages (corresponding with complete eruption of the second and third molars).

  10. Molecular genetics of human immune responsiveness to Lolium perenne (rye) allergen, Lol p III.

    Science.gov (United States)

    Ansari, A A; Freidhoff, L R; Marsh, D G

    1989-01-01

    Lol p II and III are each about 11-kD protein allergens from the pollen of Lolium perenne (rye grass). We have found that human immune responses (IgE and IgG antibodies) to both proteins are significantly associated with HLA-DR3. In addition, the two proteins are cross-reactive with the antibodies in many human sera (about 84% human sera showed the cross-reactivity). We have determined greater than 90% of the amino acid sequences of the two proteins and found that they are at least 54% homologous. Berzofsky found that 75% of the 23 known T cell sites in various proteins had an amphipathic structure. Our analysis by the same method showed that both Lol p II and III have a major region of amphipathicity (at residues 61-67, Lol p III numbering) which might contain sites for binding to an Ia molecule and a T cell receptor. This region is identical between Lol p II and III, except for an Arg-Lys substitution, and could account, in part, for the DR3 association with responsiveness to both molecules. An interesting difference between the two proteins is that immune response to Lol p III is associated with DR5 (in addition to DR3), whereas no DR5 association is found in the case of Lol p II. One possibility is that Lol p III has an additional site which binds to the DR5 Ia molecule. Lol p III indeed has a second highly amphiphathic peptide, 24-30 (Lol p III 24 R P G D T L A 30), which is different and not amphipathic in Lol p II.(ABSTRACT TRUNCATED AT 250 WORDS)

  11. Carbonato-bridged Ni(II)2Ln(III)2 (Ln(III) = Gd(III), Tb(III), Dy(III)) complexes generated by atmospheric CO2 fixation and their single-molecule-magnet behavior: [(μ4-CO3)2{Ni(II)(3-MeOsaltn)(MeOH or H2O)Ln(III)(NO3)}2]·solvent [3-MeOsaltn = N,N'-bis(3-methoxy-2-oxybenzylidene)-1,3-propanediaminato].

    Science.gov (United States)

    Sakamoto, Soichiro; Fujinami, Takeshi; Nishi, Koshiro; Matsumoto, Naohide; Mochida, Naotaka; Ishida, Takayuki; Sunatsuki, Yukinari; Re, Nazzareno

    2013-06-17

    Atmospheric CO2 fixation of [Ni(II)(3-MeOsaltn)(H2O)2]·2.5H2O [3-MeOsaltn = N,N'-bis(3-methoxy-2-oxybenzylidene)-1,3-propanediaminato], Ln(III)(NO3)3·6H2O, and triethylamine occurred in methanol/acetone, giving a first series of carbonato-bridged Ni(II)2Ln(III)2 complexes [(μ4-CO3)2{Ni(II)(3-MeOsaltn)(MeOH)Ln(III)(NO3)}2] (1Gd, 1Tb, and 1Dy). When the reaction was carried out in acetonitrile/water, it gave a second series of complexes [(μ4-CO3)2{Ni(II)(3-MeOsaltn)(H2O)Ln(III)(NO3)}2]·2CH3CN·2H2O (2Gd, 2Tb, and 2Dy). For both series, each Ni(II)2Ln(III)2 structure can be described as two di-μ-phenoxo-bridged Ni(II)Ln(III) binuclear units bridged by two carbonato CO3(2-) units to form a carbonato-bridged (μ4-CO3)2{Ni(II)2Ln(III)2} structure. The high-spin Ni(II) ion has octahedral coordination geometry, and the Ln(III) ion is coordinated by O9 donor atoms from Ni(II)(3-MeOsaltn), bidentate NO3(-), and one and two oxygen atoms of two CO3(2-) ions. The NO3(-) ion for the first series roughly lie on Ln-O(methoxy) bonds and are tilted toward the outside, while for the second series, the two oxygen atoms roughly lie on one of the Ln-O(phenoxy) bonds due to the intramolecular hydrogen bond. The temperature-dependent magnetic susceptibilities indicated a ferromagnetic interaction between the Ni(II) and Ln(III) ions (Ln(III) = Gd(III), Tb(III), Dy(III)) for all of the complexes, with a distinctly different magnetic behavior between the two series in the lowest-temperature region due to the Ln(III)-Ln(III) magnetic interaction and/or different magnetic anisotropies of the Tb(III) or Dy(III) ion. Alternating-current susceptibility measurements under the 0 and 1000 Oe direct-current (dc) bias fields showed no magnetic relaxation for the Ni(II)2Gd(III)2 complexes but exhibited an out-of-phase signal for Ni(II)2Tb(III)2 and Ni(II)2Dy(III)2, indicative of slow relaxation of magnetization. The energy barriers, Δ/kB, for the spin flipping were estimated from the Arrhenius

  12. Novel synergism by complex ligands in solvent extraction of rare earth metals(III) with β-diketones

    International Nuclear Information System (INIS)

    Imura, H.; Ebisawa, M.; Kato, M.; Ohashi, K.

    2006-01-01

    The extraction of rare earth metals(III) (RE) with hexafluoroacetylacetone (Hhfa) and 2-thenoyltrifluoroacetone (Htta) was studied in the presence of some cobalt(III) chelates such as tris(acetylacetonato)cobalt(III), tris(4-isopropyltropolonato)cobalt(III), tris(8-quinolinolato)cobalt(III), tris(8-quinolinethiolato)cobalt(III), and tris(diethyldithiocarbamato)cobalt(III) in benzene or toluene. The synergistic enhancement of the extraction of RE, especially of lanthanum(III) was found in all the systems. Therefore, those cobalt(III) chelates act as synergists or complex ligands. The equilibrium analysis and IR spectroscopic study were performed to evaluate the present synergistic mechanism. It was found that the RE-β-diketone chelates form 1:1 adducts, i.e., binuclear complexes, with the cobalt(III) chelates in the organic phase. The formation constants (β s,1 ) were determined and compared with those reported previously. The spectroscopic studies demonstrated that adducts have two different structures with inner- and outer-sphere coordination. In the former the cobalt(III) chelate directly coordinated to the RE ion and displaced the coordinated water molecules. In the latter the hydrogen-bonding was formed between the coordinating oxygen or sulfur atoms of cobalt(III) chelate and hydrogen atoms of the coordinated water molecules in the RE-β-diketone chelate. The types of the adducts are mainly due to the steric factors of the RE-β-diketone chelates and the cobalt(III) chelates

  13. Involvement of peripheral III nerve in multiple sclerosis patient: Report of a new case and discussion of the underlying mechanism.

    Science.gov (United States)

    Shor, Natalia; Amador, Maria Del Mar; Dormont, Didier; Lubetzki, Catherine; Bertrand, Anne

    2017-04-01

    Multiple sclerosis (MS) is a chronic disorder that affects the central nervous system myelin. However, a few radiological cases have documented an involvement of peripheral cranial nerves, within the subarachnoid space, in MS patients. We report the case of a 36-year-old female with a history of relapsing-remitting (RR) MS who consulted for a subacute complete paralysis of the right III nerve. Magnetic resonance imaging (MRI) examination showed enhancement and thickening of the cisternal right III nerve, in continuity with a linear, mesencephalic, acute demyelinating lesion. Radiological involvement of the cisternal part of III nerve has been reported only once in MS patients. Radiological involvement of the cisternal part of V nerve occurs more frequently, in almost 3% of MS patients. In both situations, the presence of a central demyelinating lesion, in continuity with the enhancement of the peripheral nerve, suggests that peripheral nerve damage is a secondary process, rather than a primary target of demyelination.

  14. Bone morphometry and mineral contents of the distal part of the fractured third metacarpal bone in thoroughbred racehorses

    International Nuclear Information System (INIS)

    Yoshihara, T.; Oikawa, M.; Wada, R.; Hasegawa, M.; Kaneko, M.

    1990-01-01

    Most of the bone fractures in racehorses occur in the fore limb, especially in the metacarpal joint during the racing and training. The longitudinal fracture of the third metacarpal bone (Mc III) often occurs in the osteosclerotic and/or necrotic lesions in the distal part of the bone. To elucidate the endogenous factors of its fracture, soft radiograms of 4 fractured and 4 non-fractured control cases have been investigated morphometrically by a image analyzer. In addition, to analyze the quality of these bones, 20 elements of mineral contents in the crashed bones have been measured using a fluorescent X-ray analyzer. As the results, the osteosclerotic change was observed in both groups in the plantar side of the distal part of Mc III, however, no significant differences were found in the bone morphometry. No significant differences in the 19 elements of bone mineral were found except Fe. From these findings, the mechanism of the occurrence of the longitudinal fracture in the Mc III remains to be elucidated. In future, further work needs to be done with regard to the mechanical intensity and collagen disposition of the distal part of the Mc III

  15. 40 CFR Appendix A to Subpart III... - States With Approved State Implementation Plan Revisions Concerning CAIR SO2 Opt-In Units

    Science.gov (United States)

    2010-07-01

    ... Implementation Plan Revisions Concerning CAIR SO2 Opt-In Units A Appendix A to Subpart III of Part 97 Protection... BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS CAIR SO2 Opt-in Units Pt. 97, Subpt. III... Concerning CAIR SO2 Opt-In Units 1. The following States have State Implementation Plan revisions under § 51...

  16. EGFR and its mutant EGFRvIII as modulators of tumor cell radiosensitivity

    International Nuclear Information System (INIS)

    Lammering, G.; Hewit, T.H.; Contessa, J.N.; Hawkins, W.; Lin, P.S.; Valerie, K.; Mikkelsen, R.; Dent, P.; Schmidt-Ullrich, R.K.

    2001-01-01

    Purpose: Exposure of human carcinoma and malignant glioma cells to ionizing radiation (IR)activates EGFR,which as a consequence mediates a cytoprotective response. We have demonstrated that expression of a dominant negative mutant, EGFR-CD533 disrupts this cytoprotective response, resulting in significant radiosensitization. During studies of in vivo radiosensitization with intratumoral delivery of the Adenovirus (Ad) vector, Ad-EGFR-CD533, it became apparent that xenografts from human carcinoma and malignant glioma cells invariably expressed the constitutively active EGFR mutant, EGFRvIII. This mutant EGFRvIII is frequently found in vivo in glioblastoma, breast, prostate, lung and ovarian carcinoma, but does not appear to be expressed in tumor cells under in vitro conditions. The functional consequences of EGFRvIII expression on tumor cell radiation responses are currently unknown. We have therefore investigated in a transient transfection cell system the responses of EGFRvIII and downstream signal transduction pathways to IR. In addition, the capacity of EGFR-CD533 to disrupt the function of EGFRvIII was tested. Materials and Methods: The MDA-MB-231, U-87 MG and U-373 MG cell lines were established as tumors and then intratumorally transduced with Ad-EGFR-CD533 or Ad-LacZ (control vector). The transduction efficiency was > 40% in MDA-MB-231 tumors and reached > 70% in the glioma xenografts. Radiosensitivity was measured by ex vivo colony formation and growth delay assays. The functional consequences of EGFRvIII expression on cellular IR responses were studied in transiently transfected Chinese hamster ovary (CHO) cells because tumor cells do not express EGFRvIII in vitro. Transfection with null vectors and vectors encoding either EGFRvIII or EGFR were performed and similar protein expression levels were verified by Western blot analyses. Results: The radiosensitivity of Ad-EGFR-CD533 transduced tumors was significantly increased compared with Ad-LacZ transduced

  17. National Treatment under GATT Article III: 2 and its Applicability in the Context of Korea's FTAs

    Directory of Open Access Journals (Sweden)

    Sherzod Shadikhodjaev

    2008-06-01

    Full Text Available GATT Article III: 2 on national treatment on internal taxation is an integral part of Korea's FTAs. Therefore, GATT/WTO case law provides useful guidance on proper application of this provision in the FTA context. Article III:2 involves a multi-tiered test of several issues including likeness, discriminatory threshold, and protective application of a tax measure. When the FTA parties enter into a dispute over national treatment, the problem of applicable law may arise. First, FTA panels are not obliged to rely on GATT/WTO jurisprudence. Nevertheless, given the incorporation of GATT Article III into the FTA, it is suggested that FTA panels follow WTO case law to secure consistent and predictable applGATT Article III: 2 on national treatment on internal taxation is an integral part of Korea's FTAs. Therefore, GATT/WTO case law provides useful guidance on proper application of this provision in the FTA context. Article III:2 involves a multi-tiered test of several issues including likeness, discriminatory threshold, and protective application of a tax measure. When the FTA parties enter into a dispute over national treatment, the problem of applicable law may arise. First, FTA panels are not obliged to rely on GATT/WTO jurisprudence. Nevertheless, given the incorporation of GATT Article III into the FTA, it is suggested that FTA panels follow WTO case law to secure consistent and predictable application of the national treatment rule. Second, it is questionable whether WTO panels can examine claims under the GATT-plus provisions on national treatment contained in the FTA. In order to avoid possible jurisprudential difficulties, disputing parties may choose to refer the matter to an FTA panel, instead of launching a WTO dispute settlement procedure. Alternatively, the parties may agree, pursuant to DSU Article 7.3, on non-standard terms of reference of the panel where a GATT-plus provision is explicitly listed. In both scenarios, the GATT

  18. Sorption of Cr(III) ion from aqueous solution by two kinds of modified diatomite.

    Science.gov (United States)

    Li, Er; Zeng, Xiangying

    2012-01-01

    Raw diatomite modified by microemulsion (DMM) and manganese oxide (MnD) were used for the removal of Cr(III) ions from aqueous solution. The characteristics and performance of these two types of modified diatomite on Cr(III) ion adsorption were compared. The results indicate that the Cr(III) ion adsorption capacities of diatomite were considerably improved after modifications by manganese oxide (MnO) and microemulsion. The surface area of MnD was increased because of the formation of MnO on the diatomite surface, and that of DMM was promoted owing to the existence of the hydrolyzed aromatic acid. Because of the stronger surface ionized function, the adsorption performance of Cr(III) ions in DMM was better than that in MnD. Within the experimental range of pH (i.e. 2.2-6.3), the Cr(III) ion removal of DMM (35-70%) was higher than that of MnD (33-59%) owing to the different electrostatic forces between the Cr(III) ion and the surface of the modified diatomite. The Cr(III) ion removal in MnD and DMM was improved with the increase of synthetic solution concentration in volumes from 0 to 2,500 mL.

  19. Complexes between lanthanide (III) and yttrium (III) picrates and tetra methylene sulfoxide as ligand

    International Nuclear Information System (INIS)

    Silva, M.A.A. da.

    1991-01-01

    The preparation and characterization of addition compounds between lanthanide (III) and yttrium (III) picrates and tetra methylene sulfoxide as ligand were described. The adducts were prepared in the molar relation 1 (salt): 3(ligand) in ethanol. They are microcrystalline with more intense color than those of their respective hydrated salts. At room temperature conditions they are non hygroscopic and do not present perceptible alterations. They became slightly opalescent, when heated between 363 and 423 K. At higher temperatures under several heating ratios, the behavior shown is the same: melting between 439 and 472 K. The characterization of the compounds was made by elemental analysis, electrolytic conductance measurements, X-ray powder patterns, infrared spectroscopy, visible electronic absorption and emission spectra of the neodymium (III) and europium (III), respectively. (author). 116 refs., 17 tabs., 11 figs

  20. Morphology of interior interfaces in dilute nitride III/V material systems; Morphologie innerer Grenzflaechen in verduennt stickstoffhaltigen III/V-Materialsystemen

    Energy Technology Data Exchange (ETDEWEB)

    Oberhoff, S.

    2007-12-03

    This study aims to clarify structure formation processes in dilute N-containing III/V-based material systems, using highly selective etching methods and subsequent atomic force microscopy (AFM) to expose and analyse interior interfaces. In the first part of this study it was directly proved for the first time that adding Sb during growth interruption inhibits the GI-induced structural phase transition and reduces the diffusivity on GaAs and (GaIn)(NAs) surfaces. However, applying Sb during GI does not affect the driving force of the structural phase transition. Therefore a fundamental analysis about the incorporation of Sb into GaAs, Ga(NAs) and (GaIn)(NAs) was carried out in the second part of the study. Using a combination of high resolution X-ray diffraction, transmission electron microscopy and SIMS measurements, it was verified that incorporating Sb into (GaIn)(NAs) causes an increase of the In content and a decrease of the N content. In the third part of the study, novel etching methods for the GaP-based material system Ga(NAsP) are introduced which provide the opportunity to analyse structure formation processes on interior interfaces in this material system by AFM. (orig.)

  1. Using magnetic levitation for non-destructive quality control of plastic parts.

    Science.gov (United States)

    Hennek, Jonathan W; Nemiroski, Alex; Subramaniam, Anand Bala; Bwambok, David K; Yang, Dian; Harburg, Daniel V; Tricard, Simon; Ellerbee, Audrey K; Whitesides, George M

    2015-03-04

    Magnetic levitation (MagLev) enables rapid and non-destructive quality control of plastic parts. The feasibility of MagLev as a method to: i) rapidly assess injection-molded plastic parts for defects during process optimization, ii) monitor the degradation of plastics after exposure to harsh environmental conditions, and iii) detect counterfeit polymers by density is demonstrated. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Comparing the dependability and associations with functioning of the DSM-5 Section III trait model of personality pathology and the DSM-5 Section II personality disorder model.

    Science.gov (United States)

    Chmielewski, Michael; Ruggero, Camilo J; Kotov, Roman; Liu, Keke; Krueger, Robert F

    2017-07-01

    Two competing models of personality psychopathology are included in the fifth edition of the Diagnostic Statistical Manual of Mental Disorders ( DSM-5 ; American Psychiatric Association, 2013); the traditional personality disorder (PD) model included in Section II and an alternative trait-based model included in Section III. Numerous studies have examined the validity of the alternative trait model and its official assessment instrument, the Personality Inventory for DSM-5 (PID-5; Krueger, Derringer, Markon, Watson, & Skodol, 2012). However, few studies have directly compared the trait-based model to the traditional PD model empirically in the same dataset. Moreover, to our knowledge, only a single study (Suzuki, Griffin, & Samuel, 2015) has examined the dependability of the PID-5, which is an essential component of construct validity for traits (Chmielewski & Watson, 2009; McCrae, Kurtz, Yamagata, & Terracciano, 2011). The current study directly compared the dependability of the DSM-5 traits, as assessed by the PID-5, and the traditional PD model, as assessed by the Personality Diagnostic Questionnaire-4 (PDQ-4+), in a large undergraduate sample. In addition, it evaluated and compared their associations with functioning, another essential component of personality pathology. In general, our findings indicate that most DSM-5 traits demonstrate high levels of dependability that are superior to the traditional PD model; however, some of the constructs assessed by the PID-5 may be more state like. The models were roughly equivalent in terms of their associations with functioning. The current results provide additional support for the validity of PID-5 and the DSM-5 Section III personality pathology model. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  3. Experimental studies and tests on An(III)/Ln(III) separation using the TODGA extractant

    Energy Technology Data Exchange (ETDEWEB)

    Heres, Xavier; Sorel, Christian; Miguirditchian, Manuel; Cames, Beatrice; Hill, Clement; Bisel, Isabelle; Espinoux, Denis; Viallesoubranne, Carole; Baron, Pascal; Lorrain, Brigitte [CEA/DEN/MAR/DRCP, Marcoule, BP17171, 30207 Bagnols/Ceze (France)

    2009-06-15

    Minor actinide recycling by separation and transmutation is worldwide considered as one of the most promising strategies to reduce the inventory of radioactive waste, thus contributing to make nuclear energy more sustainable. One of the different options investigated at the CEA Marcoule and within the ACSEPT project (a European collaborative project partly funded by the 7. EURATOM Framework Program) to separate trivalent minor actinide (Am(III)-Cf(III)) from the fission and activation products contained in PUREX raffinates is the TODGA process, which consists in: 1. Co-extracting trivalent 4f and 5f elements from highly acidic PUREX raffinates by a mixture of TODGA (tetraoctyl-diglycolamide) and TBP (tributyl-phosphate), dissolved in HTP (hydrogenated tetra-propene). 2. Selectively stripping the trivalent minor actinides by a hydrophilic poly-aminocarboxylic acid used as a complexing agent in a buffered aqueous solution, while the trivalent lanthanides are kept in the organic solvent thanks to a sodium nitrate salting-out effect. 3. Stripping the lanthanides in a diluted nitric acid solution. The major difficulty of this TODGA separation process is to tune the pH in a very narrow range of operating conditions in the second step, because of the high sensitivity of the performances of the flow-sheet vs pH. This difficulty was however overcome. This paper describes the development of the TODGA process from experimental studies to hot test implementation in shielded cells of the ATALANTE facility, including (i) the optimization of the extraction system (both the formulation of the organic solvent and those of the aqueous scrubbing and stripping solutions), (ii) the implementation of a cold test in small scale mixer-settlers in the G1 facility (MARCEL loop), using a surrogate feed composed of major fission products, (iii) the validation of some steps of the process, using a surrogate feed, spiked with Am-241 and Eu-152, and similar laboratory contactors (medium activity

  4. IMPLEMENTATION OF BASEL III IN THE EUROPEAN BANKING SECTOR

    Directory of Open Access Journals (Sweden)

    Ioana Sbarcea

    2015-06-01

    Full Text Available In this work, which is part of a larger research project aimed at the expected impact of Basel III on commercial banks in Romania, I decided to analyse the implementation and transposition of the new international prudential requirements into European regulations, which are of particular interest for the Romanian banking sector. I started this analysis by highlighting the peculiarities of the European banking sector at aggregate level, but also as a cross-country survey, to later highlight the views of European regulations on prudential supervision and differences to international regulations.

  5. DSM-III-R and religion.

    Science.gov (United States)

    Post, S G

    1992-07-01

    The interpretation of religion in DSM-III-R contains considerable negative bias and contributes to unfair stereotypes of religious persons. Particularly new religious movements and religious conversion are unfairly interpreted under the DSM-III-R heading, 'Dissociative Disorder Not Otherwise Specified'. It is suggested that a more balanced and respectful interpretation of religion is needed in DSM-III-R, since psychiatry through its official nomenclature should not contribute to social intolerance of religious nonconformity.

  6. A three-dimensional soft tissue analysis of Class III malocclusion: a case-controlled cross-sectional study.

    Science.gov (United States)

    Johal, Ama; Chaggar, Amrit; Zou, Li Fong

    2018-03-01

    The present study used the optical surface laser scanning technique to compare the facial features of patients aged 8-18 years presenting with Class I and Class III incisor relationship in a case-control design. Subjects with a Class III incisor relationship, aged 8-18 years, were age and gender matched with Class I control and underwent a 3-dimensional (3-D) optical surface scan of the facial soft tissues. Landmark analysis revealed Class III subjects displayed greater mean dimensions compared to the control group most notably between the ages of 8-10 and 17-18 years in both males and females, in respect of antero-posterior (P = 0.01) and vertical (P = 0.006) facial dimensions. Surface-based analysis, revealed the greatest difference in the lower facial region, followed by the mid-face, whilst the upper face remained fairly consistent. Significant detectable differences were found in the surface facial features of developing Class III subjects.

  7. Reactor oscillator - I - III, Part III - Electronic device

    International Nuclear Information System (INIS)

    Lolic, B.; Jovanovic, S.

    1961-12-01

    This report describes functioning of the reactor oscillator electronic system. Two methods of oscillator operation were discussed. The first method is so called method of amplitude modulation of the reactor power, and the second newer method is phase method. Both methods are planned for the present reactor oscillator

  8. Expression of adenylyl cyclase types III and VI in human hyperfunctioning thyroid nodules.

    Science.gov (United States)

    Celano, M; Arturi, F; Presta, I; Bruno, R; Scarpelli, D; Calvagno, M G; Cristofaro, C; Bulotta, S; Giannasio, P; Sacco, R; Filetti, S; Russo, D

    2003-05-30

    Hyperfunctioning thyroid nodules are characterized by the presence of spontaneous somatic mutations responsible for constitutive activation of the cAMP pathway. However, alterations affecting other elements of the cAMP signaling system may counteract the effects of the mutations. In this study, the expression of the adenylyl cyclase (AC) types III and VI was investigated by Western blot in 18 hyperfunctioning thyroid nodules; in 12 samples, we also assessed the presence of TSH receptor (TSHR) or gsp mutations and levels of AC VI and III mRNA. We found that the expression of nodular AC VI (but not AC III) was significantly lower (85.1% of normal, P=0.014) than the expression of both adenylyl cycles types of perinodular tissue from the same patients. Slightly, but not significant differences were detected in nodules with or without mutations and AC protein levels generally showed correlation with the levels of the transcripts detected by RT-PCR. In addition, AC III and AC VI expression levels within a given nodule were characterized by a significant positive correlation. These findings indicate that a diminished expression of AC type VI may be part of the mechanisms occurring in the hyperfunctioning nodules, independently of the presence of TSHR or gsp mutations, which influence the resulting phenotype.

  9. Stability of Tl(III) in the context of speciation analysis of thallium in plants.

    Science.gov (United States)

    Sadowska, Monika; Biaduń, Ewa; Krasnodębska-Ostręga, Beata

    2016-02-01

    The paper presents both "good" and "bad" results obtained during speciation analysis of thallium in plant tissues of a hyperaccumulator of this metal. The object was white mustard - Sinapis alba L. In this plant there were found traces of trivalent thallium. The crucial point of this study (especially in the case of so unstable thallium form as Tl(III)) was to prove that the presence of Tl(III) was not caused by the procedure of sample preparation itself, and that the whole analytical method provides reliable results. Choice of the method for conservation of the initial speciation, extraction with the highest efficiency and proving the correctness of the obtained data were the most difficult parts of the presented study. It was found that: both freezing and drying cause significant changes in the speciation of thallium; quantitative analysis could be performed only with fresh tissues of mustard plants; only short-term storage of an extract from fresh plant tissues is possible; the methodology is not the source of thallium (III); only the presence of DTPA can greatly limit the reduction of TI(III) to TI(I) (up to 1-3%); the UV irradiation results in disintegration of TI(III)DTPA in the presence of plant matrix (reduction up to 90%). Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Nucleotide sequence of a cDNA coding for the amino-terminal region of human prepro. alpha. 1(III) collagen

    Energy Technology Data Exchange (ETDEWEB)

    Toman, P D; Ricca, G A [Rorer Biotechnology, Inc., Springfield, VA (USA); de Crombrugghe, B [National Institutes of Health, Bethesda, MD (USA)

    1988-07-25

    Type III Collagen is synthesized in a variety of tissues as a precursor macromolecule containing a leader sequence, a N-propeptide, a N-telopeptide, the triple helical region, a C-telopeptide, and C-propeptide. To further characterize the human type III collagen precursor, a human placental cDNA library was constructed in gt11 using an oligonucleotide derived from a partial cDNA sequence corresponding to the carboxy-terminal part of the 1(III) collagen. A cDNA was identified which contains the leader sequence, the N-propeptide and N-telopeptide regions. The DNA sequence of these regions are presented here. The triple helical, C-telopeptide and C-propeptide amino acid sequence for human type III collagen has been determined previously. A comparison of the human amino acid sequence with mouse, chicken, and calf sequence shows 81%, 81%, and 92% similarity, respectively. At the DNA level, the sequence similarity between human and mouse or chicken type III collagen sequences in this area is 82% and 77%, respectively.

  11. Determination of Cu(III) and Cu(II)+Cu(III) in superconducting copper ceramics

    International Nuclear Information System (INIS)

    Nedelcheva, T.; Kostadinova, L.; Stoyanova-Ivanova, A.; Ivanova, I.

    1992-01-01

    Copper(III) and total copper in superconducting Y-Ba-Cu oxide and related compounds can be determinated by two successive iodimetric titrations after the sample has been dissolved under Ar in HCl/KI medium. First, the iodine equivalent to copper(III) is titrated with Na 2 S 2 O 3 solution at pH 4.8, copper(II) being masked with EDTA. The total copper is then determined in the same solution by demasking with acid and iodide, followed by iodimetric titration. The method is both accurate and reproducible. The relative standard deviations for 1.074% copper(III) and 23.37% total copper are 0.8% and 0.3%, respectively. (orig.)

  12. Treatment of groundwater containing Mn(II), Fe(II), As(III) and Sb(III) by bioaugmented quartz-sand filters.

    Science.gov (United States)

    Bai, Yaohui; Chang, Yangyang; Liang, Jinsong; Chen, Chen; Qu, Jiuhui

    2016-12-01

    High concentrations of iron (Fe(II)) and manganese (Mn(II)) often occur simultaneously in groundwater. Previously, we demonstrated that Fe(II) and Mn(II) could be oxidized to biogenic Fe-Mn oxides (BFMO) via aeration and microbial oxidation, and the formed BFMO could further oxidize and adsorb other pollutants (e.g., arsenic (As(III)) and antimony (Sb(III))). To apply this finding to groundwater remediation, we established four quartz-sand columns for treating groundwater containing Fe(II), Mn(II), As(III), and Sb(III). A Mn-oxidizing bacterium (Pseudomonas sp. QJX-1) was inoculated into two parallel bioaugmented columns. Long-term treatment (120 d) showed that bioaugmentation accelerated the formation of Fe-Mn oxides, resulting in an increase in As and Sb removal. The bioaugmented columns also exhibited higher overall treatment effect and anti-shock load capacity than that of the non-bioaugmented columns. To clarify the causal relationship between the microbial community and treatment effect, we compared the biomass of active bacteria (reverse-transcribed real-time PCR), bacterial community composition (Miseq 16S rRNA sequencing) and community function (metagenomic sequencing) between the bioaugmented and non-bioaugmented columns. Results indicated that the QJX1 strain grew steadily and attached onto the filter material surface in the bioaugmented columns. In general, the inoculated strain did not significantly alter the composition of the indigenous bacterial community, but did improve the relative abundances of xenobiotic metabolism genes and Mn oxidation gene. Thus, bioaugmentation intensified microbial degradation/utilization for the direct removal of pollutants and increased the formation of Fe-Mn oxides for the indirect removal of pollutants. Our study provides an alternative method for the treatment of groundwater containing high Fe(II), Mn(II) and As/Sb. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Speciation of Am(III)/Eu(III) sorbed on γ-alumina. Effect of metal ion concentration

    International Nuclear Information System (INIS)

    Kumar, S.; Tomar, B.S.; Godbole, S.V.

    2013-01-01

    The present paper describes the speciation of Am(III)/Eu(III) sorbed on γ-alumina, and its evolution with changing metal ion concentration, studied using batch sorption experiment, time resolved fluorescence spectroscopy (TRFS), extended X-ray absorption fine structure (EXAFS) and surface Complexation modeling (SCM). Though numerous studies exist in the literature on the speciation of trivalent actinides and lanthanides on alumina surface, the mechanism of sorption at high metal ion concentrations is not yet fully understood. Batch sorption experiments of Am(III) on γ-alumina under varying condition of pH (3-10), ionic strength (0.005-0.1 M NaClO 4 ) and metal ion concentration (10 -7 -10 -4 M) were performed. Higher metal ion concentration was achieved by the addition of Eu(III) considering it as an analogue of Am(III). Time resolved fluorescence spectroscopy (TRFS) study of Eu(III) sorbed on γ-alumina at the metal ion concentration of 5.0 x 10 -5 M was carried out over pH 4 to 7. TRFS showed the presence of two surface species, with distinctly different fluorescence decay life times. The shorter lifetime value and its changing pattern with pH indicate the surface species corresponding to this component to be monodentate species > AlOAm 2+ and its hydrolyzed forms. The sorbed Eu 3+ species corresponding to the longer lifetime value has 2-3 water molecules in its first coordination sphere and is multidentate in its binding on alumina surface. Extended X-ray absorption fine structure (EXAFS) measurement of Eu:γ-Al 2 O 3 sorption systems at pH 6.18 and 7.15 corroborate the existence of two surface complexes. Further it suggests the edge sharing bidentate binding of Eu on AlO 6 octahedra as the co-ordination mode of the higher lifetime component. Surface Complexation Modeling (SCM) of Am(III)/Eu(III) sorption onto γ-alumina at pH ≤7 has been carried out using these two surface species. 2-pK surface complexation modeling coupled with constant capacitance model

  14. Organometallic neptunium(III) complexes.

    Science.gov (United States)

    Dutkiewicz, Michał S; Farnaby, Joy H; Apostolidis, Christos; Colineau, Eric; Walter, Olaf; Magnani, Nicola; Gardiner, Michael G; Love, Jason B; Kaltsoyannis, Nikolas; Caciuffo, Roberto; Arnold, Polly L

    2016-08-01

    Studies of transuranic organometallic complexes provide a particularly valuable insight into covalent contributions to the metal-ligand bonding, in which the subtle differences between the transuranium actinide ions and their lighter lanthanide counterparts are of fundamental importance for the effective remediation of nuclear waste. Unlike the organometallic chemistry of uranium, which has focused strongly on U(III) and has seen some spectacular advances, that of the transuranics is significantly technically more challenging and has remained dormant. In the case of neptunium, it is limited mainly to Np(IV). Here we report the synthesis of three new Np(III) organometallic compounds and the characterization of their molecular and electronic structures. These studies suggest that Np(III) complexes could act as single-molecule magnets, and that the lower oxidation state of Np(II) is chemically accessible. In comparison with lanthanide analogues, significant d- and f-electron contributions to key Np(III) orbitals are observed, which shows that fundamental neptunium organometallic chemistry can provide new insights into the behaviour of f-elements.

  15. Tuning of "antenna effect" of Eu(III) in ternary systems in aqueous medium through binding with protein.

    Science.gov (United States)

    Ghorai, Shyamal Kr; Samanta, Swarna Kamal; Mukherjee, Manini; Saha Sardar, Pinki; Ghosh, Sanjib

    2013-02-04

    A simple ternary system containing a protein [human serum albumin (HSA)/bovine serum albumin (BSA)], tetracycline hydrochloride (TC), and Eu(III) in suitable aqueous buffer medium at physiological pH (= 7.2) has been shown to exhibit highly efficient "antenna effect" compared to the binary complex of TC with Eu(III) (Eu(3)TC). The ternary system containing E. coli alkaline phosphatase (AP), TC, and Eu(III), however, shows a slight enhancement of Eu(III) emission, although the binding constant of AP with TC is 2 orders of magnitude greater than with BSA/HSA. The enhanced emission of bound TC in the binary systems containing proteins and TC gets quenched in the ternary systems containing HSA/BSA, showing the efficient energy transfer (ET) from TC to Eu(III). Steady state and time-resolved emission studies of each component in all the ternary systems in H(2)O and in D(2)O medium reveal that Eu(III) is very well protected from the O-H oscillator in the ternary system containing HSA/BSA compared to that containing AP. The docking studies locating the binding site of TC in the proteins suggest that TC binds near the surface of AP. In the case of HSA/BSA, TC resides in the interior of the protein resulting in a large shielding effect of Eu(III). The rotational correlation time (θ(c)) determined from the anisotropy decay of bound TC in the complexes and the accessible surface area (ASA) of the ligand in the complexes obtained from the docking studies also support the contention that Eu(3)TC is more exposed to solvent in the case of the ternary system consisting of AP, TC, and Eu(III). The calculated radiative lifetime and the sensitization efficiency ratio of Eu(III) in all the systems clearly demonstrate the protein mediated tuning of "antenna effect" in Eu(III).

  16. Incremental binding free energies of aluminum (III) vs. magnesium (II) complexes

    International Nuclear Information System (INIS)

    Mercero, Jose M.; Mujika, Jon I.; Matxain, Jon M.; Lopez, Xabier; Ugalde, Jesus M.

    2003-01-01

    A sequential ligand addition to the aluminum (III) cation has been studied using the B3LYP functional and a combined all-electron/pseudopotentials basis set. The aluminum complexes are compared with analogous magnesium (II) complexes. Different thermodynamical data, such as incremental binding energies, enthalpies, entropies and free energies, are presented for these addition reactions. While the magnesium (II) cation can only accommodate three negatively charged ligands, aluminum (III) accommodates four even after including bulk solvent effects. The main differences between both cations complexing with the neutral ligands, is that aluminum (III) is not able to form complexes with methanol until the number of methanol ligands is equal to 3. Magnesium (II) prefers to bind methanol and formamide when the number of ligands is small, while aluminum prefers formamide. For the largest complexes both cations prefer to bind water

  17. Liquid-liquid extraction kinetics of uranyl nitrate and actinides (III)-lanthanides nitrates by extractants with amide function

    International Nuclear Information System (INIS)

    Toulemonde, V.

    1995-01-01

    Nowadays, the most important part of electric power is generated by fission energy. But spent fuels have then to be reprocessed. The production of these reprocessed materials separately and with a high purity level is done according to a liquid-liquid extraction process (Purex process) with the use of tributyl phosphate as solvent. Optimization studies concerning the extracting agent have been undertaken. This work gives the results obtained for the uranyl nitrate and the actinides (III)-lanthanides (III) nitrates extraction by extractants with amide function (monoamide for U(VI) and diamide for actinides (III) and lanthanides (III)). The extraction kinetics have been studied in the case of a metallic specie transfer from the aqueous phase towards the organic phase. The experiments show that the nitrates extraction kinetics is limited by the complexation chemical reaction of the species at the interface between the two liquids. An adsorption-desorption interfacial reactional mechanism (Langmuir theory) is proposed for the uranyl nitrate. (O.M.)

  18. Proteomic and properties analysis of botanical insecticide rhodojaponin III-induced response of the diamondback moth, Plutella xyllostella (L..

    Directory of Open Access Journals (Sweden)

    Xiaolin Dong

    Full Text Available BACKGROUND: Rhodojaponin III, as a botanical insecticide, affects a wide variety of biological processes in insects, including reduction of feeding, suspension of development, and oviposition deterring of adults in a dose-dependent manner. However, the mode of these actions remains obscure. PRINCIPAL FINDINGS: In this study, a comparative proteomic approach was adopted to examine the effect of rhodojaponin III on the Plutella xyllostella (L.. Following treating 48 hours, newly emergence moths were collected and protein samples were prepared. The proteins were separated by 2-DE, and total 31 proteins were significantly affected by rhodojaponin III compared to the control identified by MALDI-TOF/TOF-MS/MS. These differentially expressed proteins act in the nervous transduction, odorant degradation and metabolic change pathways. Further, gene expression patterns in treated and untreated moths were confirmed by qRT-PCR and western blot analysis. RNAi of the chemosensory protein (PxCSP gene resulted in oviposition significantly increased on cabbage plants treated with rhodojaponin III. CONCLUSIONS: These rhodojaponin III-induced proteins and gene properties analysis would be essential for a better understanding of the potential molecular mechanism of the response to rhodojaponin III from moths of P. xylostella.

  19. Comparison of nonpolar III-nitride vertical-cavity surface-emitting lasers with tunnel junction and ITO intracavity contacts

    KAUST Repository

    Leonard, J. T.

    2016-03-01

    We report on the lasing of III-nitride nonpolar, violet, vertical-cavity surface-emitting lasers (VCSELs) with III-nitride tunnel-junction (TJ) intracavity contacts and ion implanted apertures (IIAs). The TJ VCSELs are compared to similar VCSELs with tin-doped indium oxide (ITO) intracavity contacts. Prior to analyzing device results, we consider the relative advantages of III-nitride TJs for blue and green emitting VCSELs. The TJs are shown to be most advantageous for violet and UV VCSELs, operating near or above the absorption edge for ITO, as they significantly reduce the total internal loss in the cavity. However, for longer wavelength III-nitride VCSELs, TJs primarily offer the advantage of improved cavity design flexibility, allowing one to make the p-side thicker using a thick n-type III-nitride TJ intracavity contact. This offers improved lateral current spreading and lower loss, compare to using ITO and p-GaN, respectively. These aspects are particularly important for achieving high-power CW VCSELs, making TJs the ideal intracavity contact for any III-nitride VCSEL. A brief overview of III-nitride TJ growth methods is also given, highlighting the molecular-beam epitaxy (MBE) technique used here. Following this overview, we compare 12 mu m aperture diameter, violet emitting, TJ and ITO VCSEL experimental results, which demonstrate the significant improvement in differential efficiency and peak power resulting from the reduced loss in the TJ design. Specifically, the TJ VCSEL shows a peak power of similar to 550 mu W with a threshold current density of similar to 3.5 kA/cm(2), while the ITO VCSELs show peak powers of similar to 80 mu W and threshold current densities of similar to 7 kA/cm

  20. Comparison of nonpolar III-nitride vertical-cavity surface-emitting lasers with tunnel junction and ITO intracavity contacts

    KAUST Repository

    Leonard, J. T.; Young, E. C.; Yonkee, B. P.; Cohen, D. A.; Shen, Chao; Margalith, T.; Ng, Tien Khee; Denbaars, S. P.; Ooi, Boon S.; Speck, J. S.; Nakamura, S.

    2016-01-01

    We report on the lasing of III-nitride nonpolar, violet, vertical-cavity surface-emitting lasers (VCSELs) with III-nitride tunnel-junction (TJ) intracavity contacts and ion implanted apertures (IIAs). The TJ VCSELs are compared to similar VCSELs with tin-doped indium oxide (ITO) intracavity contacts. Prior to analyzing device results, we consider the relative advantages of III-nitride TJs for blue and green emitting VCSELs. The TJs are shown to be most advantageous for violet and UV VCSELs, operating near or above the absorption edge for ITO, as they significantly reduce the total internal loss in the cavity. However, for longer wavelength III-nitride VCSELs, TJs primarily offer the advantage of improved cavity design flexibility, allowing one to make the p-side thicker using a thick n-type III-nitride TJ intracavity contact. This offers improved lateral current spreading and lower loss, compare to using ITO and p-GaN, respectively. These aspects are particularly important for achieving high-power CW VCSELs, making TJs the ideal intracavity contact for any III-nitride VCSEL. A brief overview of III-nitride TJ growth methods is also given, highlighting the molecular-beam epitaxy (MBE) technique used here. Following this overview, we compare 12 mu m aperture diameter, violet emitting, TJ and ITO VCSEL experimental results, which demonstrate the significant improvement in differential efficiency and peak power resulting from the reduced loss in the TJ design. Specifically, the TJ VCSEL shows a peak power of similar to 550 mu W with a threshold current density of similar to 3.5 kA/cm(2), while the ITO VCSELs show peak powers of similar to 80 mu W and threshold current densities of similar to 7 kA/cm

  1. Spectroscopy and electrochemistry of U(IV/III) in basic AlCl3-EMIC

    International Nuclear Information System (INIS)

    Anderson, C.J.; Deakin, M.R.; Choppin, G.R.; Heerman, L.; D'Olieslager, W.; Pruett, D.J.

    1990-01-01

    The electrochemistry of U(IV) has been investigated in the solvent AlCl 3 -1-ethyl-3-methyl imidazolium chloride (EMIC), a room temperature ionic liquid. In basic solutions ( 3 ) the reduction of U(IV) to U(III) on glassy carbon electrodes is reversible. Spectroscopic data as well as measurements of the formal potential for U(IV)/U(III) as a function of the basic melt composition indicate that U(IV) and U(III) are both hexachloro anions. Diffusion coefficients for these species have been measured by two methods. The values are comparable to those of transition metal hexachloro complexes in the same solvent, supporting the assignment of UCl 6 2- and UCl 6 3-

  2. Optical and Temporal Carrier Dynamics Investigations of III-Nitrides for Semiconductor Lighting

    KAUST Repository

    Ajia, Idris A.

    2018-05-22

    III-nitride semiconductors suffer significant efficiency limitations; ‘efficiency’ being an umbrella term that covers an extensive list of challenges that must be overcome if they are to fulfil their vast potential. To this end, it is imperative to understand the underlying phenomena behind such limitations. In this dissertation, I combine powerful optical and structural characterization techniques to investigate the effect of different defects on the carrier dynamics in III-nitride materials for light emitting devices. The results presented herein will enhance the current understanding of the carrier mechanisms in such devices, which will lead to device efficiency improvements. In the first part of this dissertation, the effects of some important types of crystal defects present in III-nitride structures are investigated. Here, two types of defects are studied in two different III-nitride-based light emitting structures. The first defects of interest are V-pit defects in InGaN/GaN multiple quantum well (MQW) blue LEDs, where their contribution to the high-efficiency of such LEDs is discussed. In addition, the effect of these defects on the efficiency droop phenomenon in these LEDs is elucidated. Secondly, the optical effects of grain boundary defects in AlN-rich AlGaN/AlGaN MQWs is studied. In this study, it is shown that grain boundary defects may result in abnormal carrier localization behavior in these deep ultraviolet (UV) structures. While both defects are treated individually, it is evident from these studies that threading dislocation (TD) defects are an underlying contributor to the more undesirable outcomes of the said defects. In the second part, the dissertation reports on the carrier dynamics of III-nitride LED structures grown on emerging substrates—as possible efficiency enhancing techniques—aimed at mitigating the effects of TD defects. Thus, the carrier dynamics of GaN/AlGaN UV MQWs grown, for the first time, on (2̅01) – oriented β-Ga2O

  3. 45 CFR Appendix A to Part 1211 - Standards for Examiners

    Science.gov (United States)

    2010-10-01

    ... SERVICE VOLUNTEER GRIEVANCE PROCEDURES Pt. 1211, App. A Appendix A to Part 1211—Standards for Examiners An..., professional, investigative, or technical work which has demonstrated the possession of: (i) The personal... confidence of others. (iii) A good working knowledge of: The relationship between volunteer administration...

  4. Efficient n-type doping of zinc-blende III-V semiconductor nanowires

    Science.gov (United States)

    Besteiro, Lucas V.; Tortajada, Luis; Souto, J.; Gallego, L. J.; Chelikowsky, James R.; Alemany, M. M. G.

    2014-03-01

    We demonstrate that it is preferable to dope III-V semiconductor nanowires by n-type anion substitution as opposed to cation substitution. Specifically, we show the dopability of zinc-blende nanowires is more efficient when the dopants are placed at the anion site as quantified by formation energies and the stabilization of DX-like defect centers. The comparison with previous work on n - type III-V semiconductor nanocrystals also allows to determine the role of dimensionality and quantum confinement on doping characteristics of materials. Our results are based on first-principles calculations of InP nanowires by using the PARSEC code. Work supported by the Spanish MICINN (FIS2012-33126) and Xunta de Galicia (GPC2013-043) in conjunction with FEDER. JRC acknowledges support from DoE (DE-FG02-06ER46286 and DESC0008877). Computational support was provided in part by CESGA.

  5. Temporal development of cross-neutralization between HTLV-III B and HTLV-III RF in experimentally infected chimpanzees

    NARCIS (Netherlands)

    Goudsmit, J.; Thiriart, C.; Smit, L.; Bruck, C.; Gibbs, C. J.

    1988-01-01

    Sera from chimpanzees inoculated respectively with HTLV-III B, LAV, HTLV-III RF and brain tissue from an AIDS patient were analysed for neutralizing activity by two methods: a cell fusion inhibition test (CFI) using HTLV-III B infected cells as inoculum and CD4+ cells as target and a replication

  6. Quando o passado legitima o presente: a música no III Reich

    Directory of Open Access Journals (Sweden)

    Sílvia Sônia Simões

    2010-10-01

    Full Text Available Este pequeno artigo é parte de um trabalho maior intitulado Música e História na República de Weimar e no III Reich: uma aproximação possível, e visa ressaltar as formas de adequação utilizadas pelo nazismo no campo musical, buscando um entendimento de qual foi a música que este regime considerou adequada para expressar sua ideologia.

  7. Radiometric titration of thallium(III) with EDTA

    International Nuclear Information System (INIS)

    Rao, V.R.S.; Pulla Rao, Ch.; Tataiah, G.

    1978-01-01

    Radioactive solutions containing very small amounts of thallium(III) can be determined by radiometric titration using ammonia as hydrolysing agent. Aqueous solution of thallium(I) (both inactive and radioactive) is treated with bromine water till the appearance of the brown colour of bromine, and the solution is warmed to 80 deg C to expel the excess bromine. By this procedure all thallium(I) is quantitatively oxidised to thallium(III). An aqueous solution of ammonia is added to precipitate thallium(III) as thallic oxide. It is then filtered, washed with water to free it from bromide and then dissolved in 2N HCl and the solution is then standardised. 2 ml of this solution is transferred to a 20 ml volumetric flask, 1 ml of radioactive thallium(III) solution to be standardised is added as well as incremental amounts of EDTA solution and mixed thoroughly. Uncomplexed thallium(III) is then precipitated by the addition of an ammonia solution and diluted to 20 ml. Required amount of this mixture is centrifuged. The beta activity of the supernatant aliquot is measured using a GM counter. Quantitative determination of Tl(III) in the range of 1-10 μM can be carried out. The interference of cations such as Au(III), iron(III), Ga(III) can be eliminated by pretreatment of the Tl(III) solution before carrying out radiometric titration. The results obtained are reproducible and accurate to +-3%. (T.I.)

  8. Positional stability experiment and analysis of elongated plasmas in Doublet III

    International Nuclear Information System (INIS)

    Yokomizo, Hideaki

    1984-04-01

    Control systems of the plasma position and shape on Doublet III are explained and experimental results of vertical stability of elongated plasmas are reviewed. Observed results of the vertical instability are qualitatively compared with the predictions from the simplified model and quantitatively compared with the numerical calculations based on a more realistic model. Experiments are in reasonable agreement with the theoretical analyses. (author)

  9. Comparative Study Of Private And Public Schools Student ...

    African Journals Online (AJOL)

    Student perceptions of school engagement (i.e., sense of connection to school, teachers and peers), motivation to learn, self-esteem, and student safety are part of a range of public accountability indicators. This study examined differences between two groups of Senior Secondary three (SS III) students from public school ...

  10. Single-molecule magnetism in three related {Co(III)2Dy(III)2}-acetylacetonate complexes with multiple relaxation mechanisms.

    Science.gov (United States)

    Langley, Stuart K; Chilton, Nicholas F; Moubaraki, Boujemaa; Murray, Keith S

    2013-06-17

    Three new heterometallic complexes with formulas of [Dy(III)2Co(III)2(OMe)2(teaH)2(acac)4(NO3)2] (1), [Dy(III)2Co(III)2(OH)2(teaH)2(acac)4(NO3)2]·4H2O (2), and [Dy(III)2Co(III)2(OMe)2(mdea)2(acac)4(NO3)2] (3) were characterized by single-crystal X-ray diffraction and by dc and ac magnetic susceptibility measurements. All three complexes have an identical "butterfly"-type metallic core that consists of two Dy(III) ions occupying the "body" position and two diamagnetic low-spin Co(III) ions occupying the outer "wing-tips". Each complex displays single-molecule magnet (SMM) behavior in zero applied magnetic field, with thermally activated anisotropy barriers of 27, 28, and 38 K above 7.5 K for 1-3, respectively, as well as observing a temperature-independent mechanism of relaxation below 5 K for 1 and 2 and at 3 K for 3, indicating fast quantum tunneling of magnetization (QTM). A second, faster thermally activated relaxation mechanism may also be active under a zero applied dc field as derived from the Cole-Cole data. Interestingly, these complexes demonstrate further relaxation modes that are strongly dependent upon the application of a static dc magnetic field. Dilution experiments that were performed on 1, in the {Y(III)2Co(III)2} diamagnetic analog, show that the slow magnetic relaxation is of a single-ion origin, but it was found that the neighboring ion also plays an important role in the overall relaxation dynamics.

  11. III-V microelectronics

    CERN Document Server

    Nougier, JP

    1991-01-01

    As is well known, Silicon widely dominates the market of semiconductor devices and circuits, and in particular is well suited for Ultra Large Scale Integration processes. However, a number of III-V compound semiconductor devices and circuits have recently been built, and the contributions in this volume are devoted to those types of materials, which offer a number of interesting properties. Taking into account the great variety of problems encountered and of their mutual correlations when fabricating a circuit or even a device, most of the aspects of III-V microelectronics, from fundamental p

  12. Antithrombin III for critically ill patients

    DEFF Research Database (Denmark)

    Allingstrup, Mikkel; Wetterslev, Jørn; Ravn, Frederikke B

    2016-01-01

    PURPOSE: Antithrombin III (AT III) is an anticoagulant with anti-inflammatory properties. We assessed the benefits and harms of AT III in critically ill patients. METHODS: We searched from inception to 27 August 2015 in CENTRAL, MEDLINE, EMBASE, CAB, BIOSIS and CINAHL. We included randomized...... participants). However, for all other outcome measures and analyses, the results did not reach statistical significance. CONCLUSIONS: There is insufficient evidence to support AT III substitution in any category of critically ill participants including those with sepsis and DIC. AT III did not show an impact...

  13. Cardiac nuclear medicine, part II: diagnosis of coronary artery diseas

    International Nuclear Information System (INIS)

    Polak, J.F.; Holman, B.L.

    1981-01-01

    Diagnosing coronary artery disease is difficult and requires careful consideration of the roles and limitations of the tests used. Standard ECG tests are not reliable indicators of the presence of disease in asymptomatic patients. Thallium stress testing to assess ischemia and exercise ventriculography to assess functional status of the heart are limited in sensitivity and specificity. This is the second of a three-part series on cardiac nuclear medicine. Part I (Med. Instrum., May-June, 1981) focused on the commonly used examinations in cardiac physiology and pathophysiology. Part III will focus on myocardial infarction and other cardiac diseases

  14. Moessbauer studies of iron(III)-(indole-3-alkanoic acids) systems in frozen aqueous solutions

    International Nuclear Information System (INIS)

    Kovacs, K.; Kuzmann, E.; Homonnay, Z.; Szilagyi, P.A.; Vertes, A.; Kamnev, A.A.; Sharma, V.K.

    2005-01-01

    Moessbauer investigations of iron(III) salts in aqueous solutions in the presence of indole-3-alkanoic acid ligands are described. The measurements showed two parallel reactions between the ligands and ferric ions: a complex formation and a redox process. The oxidation process takes place in the ligands, and a part of Fe 3+ is reduced to Fe 2+ . (author)

  15. Alteration of Occlusal Plane in Orthognathic Surgery: Clinical Features to Help Treatment Planning on Class III Patients

    Directory of Open Access Journals (Sweden)

    Daniel Amaral Alves Marlière

    2018-01-01

    Full Text Available Dentofacial deformities (DFD presenting mainly as Class III malocclusions that require orthognathic surgery as a part of definitive treatment. Class III patients can have obvious signs such as increasing the chin projection and chin throat length, nasolabial folds, reverse overjet, and lack of upper lip support. However, Class III patients can present different facial patterns depending on the angulation of occlusal plane (OP, and only bite correction does not always lead to the improvement of the facial esthetic. We described two Class III patients with different clinical features and inclination of OP and had undergone different treatment planning based on 6 clinical features: (I facial type; (II upper incisor display at rest; (III dental and gingival display on smile; (IV soft tissue support; (V chin projection; and (VI lower lip projection. These patients were submitted to orthognathic surgery with different treatment plannings: a clockwise rotation and counterclockwise rotation of OP according to their facial features. The clinical features and OP inclination helped to define treatment planning by clockwise and counterclockwise rotations of the maxillomandibular complex, and two patients undergone to bimaxillary orthognathic surgery showed harmonic outcomes and stables after 2 years of follow-up.

  16. PEEK versus titanium locking plates for proximal humerus fracture fixation: a comparative biomechanical study in two- and three-part fractures.

    Science.gov (United States)

    Schliemann, Benedikt; Seifert, Robert; Theisen, Christina; Gehweiler, Dominic; Wähnert, Dirk; Schulze, Martin; Raschke, Michael J; Weimann, Andre

    2017-01-01

    The high rigidity of metal implants may be a cause of failure after fixation of proximal humerus fractures. Carbon fiber-reinforced polyetheretherketone (PEEK) plates with a modulus similar to human cortical bone may help to overcome this problem. The present study assesses the biomechanical behavior of a PEEK plate compared with a titanium locking plate. Unstable two- and three-part fractures were simulated in 12 pairs of cadaveric humeri and were fixed with either a PEEK or a titanium locking plate using a pairwise comparison. With an optical motion capture system, the stiffness, failure load, plate bending, and the relative motion at the bone-implant interface and at the fracture site were evaluated. The mean load to failure for two- and three-part fracture fixations was, respectively, 191 N (range 102-356 N) and 142 N (range 102-169 N) in the PEEK plate group compared with 286 N (range 191-395 N) and 258 N (range 155-366 N) in the titanium locking plate group. The PEEK plate showed significantly more bending in both the two- and three-part fractures (p PEEK plate showed lower fixation strength and increased motion at the bone-implant interface compared with a titanium locking plate.

  17. A view from Cheyenne Mountain: Generation III's perspective of Keystone III.

    Science.gov (United States)

    Bliss, Erika; Cadwallader, Kara; Steyer, Terrence E; Clements, Deborah S; Devoe, Jennifer E; Fink, Kenneth; Khubesrian, Marina; Lyons, Paul; Steiner, Elizabeth; Weismiller, David

    2014-01-01

    In October 2000 the family of family medicine convened the Keystone III conference at Cheyenne Mountain Resort. Keystone III participants included members of Generation I (entered practice before 1970), Generation II (entered 1970-1990), and Generation III (entered after 1990). They represented a wide range of family physicians, from medical students to founders of the discipline, and from small-town solo practice to academic medicine. During the conference, the three generations worked together and separately thinking about the past, present, and future of family medicine, our roles in it, and how the understanding of a family physician and our discipline had and would continue to evolve. After the conference, the 10 Generation III members wrote the article published here, reflecting on our experiences as new physicians and physicians in training, and the similarities and differences between our experiences and those of physicians in Generations I and II. Key similarities included commitment to whole-person care, to a wide scope of practice, to community health, and to ongoing engagement with our discipline. Key differences included our understanding of availability, the need for work-life balance, the role of technology in the physician-patient relationship, and the perceptions of the relationship between medicine and a range of outside forces such as insurance and government. This article, presented with only minor edits, thus reflects accurately our perceptions in late 2000. The accompanying editorial reflects our current perspective.

  18. Extracción de cromo con disolventes orgánicos. III parte. Aplicación al tratamiento de residuos polimetálicos industriales

    OpenAIRE

    de Juan, D.; Meseguer, V.; Lozano, L. J.

    1998-01-01

    The use of Primene 81R as extraction agent of chromium present in solid wastes containing nickel, iron and copper has been studied. The waste was leached with a sulphuric acid solution up to pH 3 and oxidation of Cr(III) to Cr(VI) with Caro acid was also studied. Because of the negative result of oxidation, the treatment was applied on Cr(III) directly. Extraction/scrubbing/stripping process was studied in the leach. The composition of organic phase used in the extraction step was 10 % v/v Pr...

  19. Antithrombin III for critically ill patients

    DEFF Research Database (Denmark)

    Allingstrup, Mikkel; Wetterslev, Jørn; Ravn, Frederikke B

    2016-01-01

    Background: Critical illness is associated with uncontrolled inflammation and vascular damage which can result in multiple organ failure and death. Antithrombin III (AT III) is an anticoagulant with anti-inflammatory properties but the efficacy and any harmful effects of AT III supplementation...... in critically ill patients are unknown. This review was published in 2008 and updated in 2015.  Objectives: To examine: 1. The effect of AT III on mortality in critically ill participants. 2. The benefits and harms of AT III. We investigated complications specific and not specific to the trial intervention......, bleeding events, the effect on sepsis and disseminated intravascular coagulation (DIC) and the length of stay in the intensive care unit (ICU) and in hospital in general.  Search methods: We searched the following databases from inception to 27 August 2015: Cochrane Central Register of Controlled Trials...

  20. Differentiation of grade II/III and grade IV glioma by combining ''T1 contrast-enhanced brain perfusion imaging'' and susceptibility-weighted quantitative imaging

    International Nuclear Information System (INIS)

    Saini, Jitender; Gupta, Pradeep Kumar; Gupta, Rakesh Kumar; Sahoo, Prativa; Singh, Anup; Patir, Rana; Ahlawat, Suneeta; Beniwal, Manish; Thennarasu, K.; Santosh, Vani

    2018-01-01

    MRI is a useful method for discriminating low- and high-grade glioma using perfusion MRI and susceptibility-weighted imaging (SWI). The purpose of this study is to evaluate the usefulness of T1-perfusion MRI and SWI in discriminating among grade II, III, and IV gliomas. T1-perfusion MRI was used to measure relative cerebral blood volume (rCBV) in 129 patients with glioma (70 grade IV, 33 grade III, and 26 grade II tumors). SWI was also used to measure the intratumoral susceptibility signal intensity (ITSS) scores for each tumor in these patients. rCBV and ITSS values were compared to seek differences between grade II vs. grade III, grade III vs. grade IV, and grade III+II vs. grade IV tumors. Significant differences in rCBV values of the three grades of the tumors were noted and pairwise comparisons showed significantly higher rCBV values in grade IV tumors as compared to grade III tumors, and similarly increased rCBV was seen in the grade III tumors as compared to grade II tumors (p < 0.001). Grade IV gliomas showed significantly higher ITSS scores on SWI as compared to grade III tumors (p < 0.001) whereas insignificant difference was seen on comparing ITSS scores of grade III with grade II tumors. Combining the rCBV and ITSS resulted in significant improvement in the discrimination of grade III from grade IV tumors. The combination of rCBV values derived from T1-perfusion MRI and SWI derived ITSS scores improves the diagnostic accuracy for discrimination of grade III from grade IV gliomas. (orig.)

  1. Differentiation of grade II/III and grade IV glioma by combining ''T1 contrast-enhanced brain perfusion imaging'' and susceptibility-weighted quantitative imaging

    Energy Technology Data Exchange (ETDEWEB)

    Saini, Jitender [National Institute of Mental Health and Neurosciences, Neuroimaging and Interventional Radiology, Bangalore (India); Gupta, Pradeep Kumar; Gupta, Rakesh Kumar [Fortis Memorial Research Institute, Department of Radiology and Imaging, Gurugram (India); Sahoo, Prativa [Philips Health System, Philips India Limited, Bangalore (India); Beckman Research Institute, Mathematical Oncology, Duarte, CA (United States); Singh, Anup [Indian Institute of Technology Delhi, Center for Biomedical Engineering, Delhi (India); Patir, Rana [Fortis Memorial Research Institute, Department of Neurosurgery, Gurugram (India); Ahlawat, Suneeta [Fortis Memorial Research Institute, SRL Diagnostics, Gurugram (India); Beniwal, Manish [National Institute of Mental Health and Neurosciences, Department of Neurosurgery, Bangalore (India); Thennarasu, K. [National Institute of Mental Health and Neurosciences, Department of Biostatistics, Bangalore (India); Santosh, Vani [National Institute of Mental Health and Neurosciences, Department of Neuropathology, Bangalore (India)

    2018-01-15

    MRI is a useful method for discriminating low- and high-grade glioma using perfusion MRI and susceptibility-weighted imaging (SWI). The purpose of this study is to evaluate the usefulness of T1-perfusion MRI and SWI in discriminating among grade II, III, and IV gliomas. T1-perfusion MRI was used to measure relative cerebral blood volume (rCBV) in 129 patients with glioma (70 grade IV, 33 grade III, and 26 grade II tumors). SWI was also used to measure the intratumoral susceptibility signal intensity (ITSS) scores for each tumor in these patients. rCBV and ITSS values were compared to seek differences between grade II vs. grade III, grade III vs. grade IV, and grade III+II vs. grade IV tumors. Significant differences in rCBV values of the three grades of the tumors were noted and pairwise comparisons showed significantly higher rCBV values in grade IV tumors as compared to grade III tumors, and similarly increased rCBV was seen in the grade III tumors as compared to grade II tumors (p < 0.001). Grade IV gliomas showed significantly higher ITSS scores on SWI as compared to grade III tumors (p < 0.001) whereas insignificant difference was seen on comparing ITSS scores of grade III with grade II tumors. Combining the rCBV and ITSS resulted in significant improvement in the discrimination of grade III from grade IV tumors. The combination of rCBV values derived from T1-perfusion MRI and SWI derived ITSS scores improves the diagnostic accuracy for discrimination of grade III from grade IV gliomas. (orig.)

  2. Addition compounds of lanthamide (III) and yttrium (III) hexafluorophosphates and N,N - dimethylformamide

    International Nuclear Information System (INIS)

    Braga, L.S.P.

    1983-01-01

    Addition compounds of lanthanide (III) and yttrium (III) hexafluorophosphates and N-N-Dimetylformamide are described to characterize the complexes, elemental analysis, melting ranges, molar conductance measurements, X-ray powder patters infrared and Raman spectra, TG and DTA curves, are studied. Information concerning the decomposition of the adducts through the thermogravimetric curves and the differential thermal analysis curves is obtained. (M.J.C.) [pt

  3. Long-term outcomes of Class III treatment with mandibular cervical headgear followed by fixed appliances.

    Science.gov (United States)

    Baccetti, Tiziano; Rey, Diego; Oberti, Giovanni; Stahl, Franka; McNamara, James A

    2009-09-01

    To evaluate the stability of the outcomes of mandibular cervical headgear (MCH) and fixed appliance-treated Class III patients at a long-term posttreatment (5 years) observation, compared with well-matched untreated Class III controls, following a previous report on the short-term outcomes of this protocol. The treated group consisted of 20 patients with dentoskeletal Class III malocclusions treated with a two-phase protocol consisting of MCH and fixed appliances, while the control group comprised 18 untreated subjects with similar dentoskeletal Class III malocclusion. Lateral cephalograms of both patients and controls were analyzed at two time points: posttreatment (PT), after two-phase treatment; and long term (LT). All patients were at a postpubertal stage of skeletal maturity at PT, and they showed CS6 at LT, thus revealing completion of pubertal craniofacial growth. In the long term, the treatment group showed significantly smaller values for mandibular length (Co-Gn), SNB angle, maxillomandibular differential, and molar relation. When compared with the controls, the treated patients exhibited also greater values for ANB angle, Wits appraisal, and overjet at LT. No significant difference between the two groups was found for the changes occurring from PT to LT. Favorable dentoskeletal outcomes induced by MCH and fixed appliances remained stable in the long term; untreated Class III malocclusion did not show any tendency toward self-improvement during the postpubertal interval.

  4. Characterization of Fe (III)-reducing enrichment culture and isolation of Fe (III)-reducing bacterium Enterobacter sp. L6 from marine sediment.

    Science.gov (United States)

    Liu, Hongyan; Wang, Hongyu

    2016-07-01

    To enrich the Fe (III)-reducing bacteria, sludge from marine sediment was inoculated into the medium using Fe (OH)3 as the sole electron acceptor. Efficiency of Fe (III) reduction and composition of Fe (III)-reducing enrichment culture were analyzed. The results indicated that the Fe (III)-reducing enrichment culture with the dominant bacteria relating to Clostridium and Enterobacter sp. had high Fe (III) reduction of (2.73 ± 0.13) mmol/L-Fe (II). A new Fe (III)-reducing bacterium was isolated from the Fe (III)-reducing enrichment culture and identified as Enterobacter sp. L6 by 16S rRNA gene sequence analysis. The Fe (III)-reducing ability of strain L6 under different culture conditions was investigated. The results indicated that strain L6 had high Fe (III)-reducing activity using glucose and pyruvate as carbon sources. Strain L6 could reduce Fe (III) at the range of NaCl concentrations tested and had the highest Fe (III) reduction of (4.63 ± 0.27) mmol/L Fe (II) at the NaCl concentration of 4 g/L. This strain L6 could reduce Fe (III) with unique properties in adaptability to salt variation, which indicated that it can be used as a model organism to study Fe (III)-reducing activity isolated from marine environment. Copyright © 2015 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  5. The study of Cr(III) complexation in the xylem sap using ion exchange and radiotracer

    International Nuclear Information System (INIS)

    Juneja, Shikha; Prakash, Satya

    2003-01-01

    Radiotracer was employed to carry out ion exchange experiments to study the chromium speciation in the in vitro samples of xylem sap of maize stem of 60 days old plants. Cr(III) radiolabelled with its radioactive isotope ( 51 Cr) was mixed with both the ion exchange fraction of the sap which represented the carboxylic acids, as well as the whole sap and was analysed for complexation after 10 and 30 days at 25 degC. Prior to this, the ion exchange elution chromatography of Cr(III), and the Cr(III) complexes with oxalic and citric acid were used to compare the complexes being formed in the in vitro studies. The in vitro Cr(III) complexation results indicated that Cr(III) was vitally present as anionic species. The elution curve trend was similar to that of citric acid complexation. Citric acid was also found to be the major complexing acid in the xylem sap as determined by HPLC. The results indicate the transportation of Cr(III) as a citrate complex in the xylem sap of maize plants. (author)

  6. A binuclear Fe(III)Dy(III) single molecule magnet. Quantum effects and models.

    Science.gov (United States)

    Ferbinteanu, Marilena; Kajiwara, Takashi; Choi, Kwang-Yong; Nojiri, Hiroyuki; Nakamoto, Akio; Kojima, Norimichi; Cimpoesu, Fanica; Fujimura, Yuichi; Takaishi, Shinya; Yamashita, Masahiro

    2006-07-19

    The binuclear [FeIII(bpca)(mu-bpca)Dy(NO3)4], having Single Molecule Magnet (SMM) properties, belonging to a series of isostructural FeIIILnIII complexes (Ln = Eu, Gd, Tb, Dy, Ho) and closely related FeIILnIII chain structures, was characterized in concise experimental and theoretical respects. The low temperature magnetization data showed hysteresis and tunneling. The anomalous temperature dependence of Mössbauer spectra is related to the onset of magnetic order, consistent with the magnetization relaxation time scale resulting from AC susceptibility measurements. The advanced ab initio calculations (CASSCF and spin-orbit) revealed the interplay of ligand field, spin-orbit, and exchange effects and probed the effective Ising nature of the lowest states, involved in the SMM and tunneling effects.

  7. Biomonitoring chromium III or VI soluble pollution by moss chlorophyll fluorescence.

    Science.gov (United States)

    Chen, Yang-Er; Mao, Hao-Tian; Ma, Jie; Wu, Nan; Zhang, Chao-Ming; Su, Yan-Qiu; Zhang, Zhong-Wei; Yuan, Ming; Zhang, Huai-Yu; Zeng, Xian-Yin; Yuan, Shu

    2018-03-01

    We systematically compared the impacts of four Cr salts (chromic chloride, chromic nitrate, potassium chromate and potassium bichromate) on physiological parameters and chlorophyll fluorescence in indigenous moss Taxiphyllum taxirameum. Among the four Cr salts, K 2 Cr 2 O 7 treatment resulted in the most significant decrease in photosynthetic efficiency and antioxidant enzymes, increase in reactive oxygen species (ROS), and obvious cell death. Different form the higher plants, although hexavalent Cr(VI) salt treatments resulted in higher accumulation levels of Cr and were more toxic than Cr(III) salts, Cr(III) also induced significant changes in moss physiological parameters and chlorophyll fluorescence. Our results showed that Cr(III) and Cr(VI) could be monitored distinguishably according to the non-photochemical quenching (NPQ) fluorescence of sporadic purple and sporadic lavender images respectively. Then, the valence states and concentrations of Cr contaminations could be evaluated according to the image of maximum efficiency of PSII photochemistry (Fv/Fm) and the quantum yield of PSII electron transport (ΦPSII). Therefore, this study provides new ideas of moss's sensibility to Cr(III) and a new method to monitor Chromium contaminations rapidly and non-invasively in water. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Comparative study of binary and ternary complexes of some rare earths

    International Nuclear Information System (INIS)

    Makhijani, S.D.; Sangal, S.P.

    1978-01-01

    Modified form of Irving and Rossotti's pH titration technique has been used to evaluate and compare the stability constants of the binary and ternary complexes of Sc(III), Y(III), La(III), Pr(III), Nd(III) and Sm(III) at 30 0 at an ionic strength of 0.2M NaClO 4 . For the study of ternary complexes, nitrilotriacetic acid has been used as a primary ligand and polyhydroxy phenols i.e. pyrocatechol (PYC), pyrogallol (PYG) and gallic acid (GA) as secondary ligands. The stability constants of the binary complexes were found to be more than those of the corresponding ternary complexes which can reasonably be explained on the basis of electrostatic force between primary complex (metal in the case of binary complex) and secondary ligand, and space available to accommodate the secondary ligand. The stability decreases with the increase in ionic radii, i.e. Sc(III)>Y(III)>Sm(III)>Nd(III)>Pr(III)>La(III). In terms of secondary ligand, it follows the order PYC>GA>PYG. Rare earths form only 1:1 binary complex, and 1:1:1 mixed ligand complex in all the cases. (author)

  9. The meridian system and mechanism of acupuncture—A comparative review. Part 1: The meridian system

    Directory of Open Access Journals (Sweden)

    Shyang Chang

    2012-12-01

    Full Text Available In traditional Chinese medicine (TCM, acupuncture has been used to heal various diseases and physiologic malfunctions in clinical practice for more than 2500 years. Due to its efficacy, acupuncture has been recommended by the World Health Organization in 1980 as an effective alternative therapy for 43 different disorders. Over the past few decades, various theories of the meridian system and mechanisms have been proposed to explain how acupuncture might work. Most of these mechanisms, however, cannot yet explain conclusively why acupuncture is efficacious in treating so many different diseases. A plausible mechanism has been unavailable until recently. This is the first of a three-part series that aims to provide a comparative review of the aforementioned topics. Part 1 reviews the current indications for acupuncture, basic concepts of TCM, and the essence of the meridian system. To establish a mathematically rigorous framework of TCM, the chaotic wave theory of fractal continuum is proposed. This theory is then applied to characterize the essence of the meridian system. Parts 2 and 3 will review the possible mechanisms of acupuncture analgesia and acupuncture therapies, respectively, based on biochemical, bioelectromagnetic, chaotic wave, and neurophysiologic approaches. It is sincerely hoped that this series of review articles can promote an understanding of the meridian system and acupuncture mechanisms to help patients in a logical and passionate way.

  10. Simultaneous Oxidation and Sequestration of As(III) from Water by Using Redox Polymer-Based Fe(III) Oxide Nanocomposite.

    Science.gov (United States)

    Zhang, Xiaolin; Wu, Mengfei; Dong, Hao; Li, Hongchao; Pan, Bingcai

    2017-06-06

    Water decontamination from As(III) is an urgent but still challenging task. Herein, we fabricated a bifunctional nanocomposite HFO@PS-Cl for highly efficient removal of As(III), with active chlorine covalently binding spherical polystyrene host for in situ oxidation of As(III) to As(V), and Fe(III) hydroxide (HFO) nanoparticles (NPs) embedded inside for specific As(V) removal. HFO@PS-Cl could work effectively in a wide pH range (5-9), and other substances like sulfate, chloride, bicarbonate, silicate, and humic acid exert insignificant effect on As(III) removal. As(III) sequestration is realized via two pathways, that is, oxidation to As(V) by the active chlorine followed by specific As(V) adsorption onto HFO NPs, and As(III) adsorption onto HFO NPs followed by oxidation to As(V). The exhausted HFO@PS-Cl could be refreshed for cyclic runs with insignificant capacity loss by the combined regeneration strategy, that is, alkaline solution to rinse the adsorbed As(V) and NaClO solution to renew the host oxidation capability. In addition, fixed-bed experiments demonstrated that the HFO@PS-Cl column could generate >1760 bed volume (BV) effluent from a synthetic As(III)-containing groundwater to meet the drinking water standard (nanocomposites, HFO@PS-N and HFO@D201 could only generate 450 and 600 BV effluents under otherwise identical conditions.

  11. Construction of Polynuclear Lanthanide (Ln = Dy(III), Tb(III), and Nd(III)) Cage Complexes Using Pyridine-Pyrazole-Based Ligands: Versatile Molecular Topologies and SMM Behavior.

    Science.gov (United States)

    Bala, Sukhen; Sen Bishwas, Mousumi; Pramanik, Bhaskar; Khanra, Sumit; Fromm, Katharina M; Poddar, Pankaj; Mondal, Raju

    2015-09-08

    Employment of two different pyridyl-pyrazolyl-based ligands afforded three octanuclear lanthanide(III) (Ln = Dy, Tb) cage compounds and one hexanuclear neodymium(III) coordination cage, exhibiting versatile molecular architectures including a butterfly core. Relatively less common semirigid pyridyl-pyrazolyl-based asymmetric ligand systems show an interesting trend of forming polynuclear lanthanide cage complexes with different coordination environments around the metal centers. It is noteworthy here that construction of lanthanide complex itself is a challenging task in a ligand system as soft N-donor rich as pyridyl-pyrazol. We report herein some lanthanide complexes using ligand containing only one or two O-donors compare to five N-coordinating sites. The resultant multinuclear lanthanide complexes show interesting magnetic and spectroscopic features originating from different spatial arrangements of the metal ions. Alternating current (ac) susceptibility measurements of the two dysprosium complexes display frequency- and temperature-dependent out-of-phase signals in zero and 0.5 T direct current field, a typical characteristic feature of single-molecule magnet (SMM) behavior, indicating different energy reversal barriers due to different molecular topologies. Another aspect of this work is the occurrence of the not-so-common SMM behavior of the terbium complex, further confirmed by ac susceptibility measurement.

  12. Data report on spray cooling test by ROSA-III, (1)

    International Nuclear Information System (INIS)

    Sobajima, Makoto; Murata, Hideo; Shiba, Masayoshi

    1980-03-01

    A separate effect test on spray cooling was carried out using one core channel of ROSA-III BWR LOCA test facility. This report describes a heating experiment in the series of runs. (1) The cooling from top of the core by spray easily causes countercurrent flow limit due to the vaparization of falling water itself, so it becomes in effective. (2) The cooling by falling water is irregular and unstable. Therefore, the cooling by the falling water is not to be relied on. (3) CCFL at porous plate is hard to occur, compared with single pipe. A quantitative study of this is desired to evaluate reflooding rate. Some suggestions for ROSA-III design are also made. (author)

  13. Epidermal Growth Factor Receptor Variant III (EGFRvIII) Positivity in EGFR-Amplified Glioblastomas: Prognostic Role and Comparison between Primary and Recurrent Tumors.

    Science.gov (United States)

    Felsberg, Jörg; Hentschel, Bettina; Kaulich, Kerstin; Gramatzki, Dorothee; Zacher, Angela; Malzkorn, Bastian; Kamp, Marcel; Sabel, Michael; Simon, Matthias; Westphal, Manfred; Schackert, Gabriele; Tonn, Jörg C; Pietsch, Torsten; von Deimling, Andreas; Loeffler, Markus; Reifenberger, Guido; Weller, Michael

    2017-11-15

    Purpose: Approximately 40% of all glioblastomas have amplified the EGFR gene, and about half of these tumors express the EGFRvIII variant. The prognostic role of EGFRvIII in EGFR -amplified glioblastoma patients and changes in EGFRvIII expression in recurrent versus primary glioblastomas remain controversial, but such data are highly relevant for EGFRvIII-targeted therapies. Experimental Design: EGFR -amplified glioblastomas from 106 patients were assessed for EGFRvIII positivity. Changes in EGFR amplification and EGFRvIII status from primary to recurrent glioblastomas were evaluated in 40 patients with EGFR -amplified tumors and 33 patients with EGFR -nonamplified tumors. EGFR single-nucleotide variants (SNV) were assessed in 27 patients. Data were correlated with outcome and validated in 150 glioblastoma patients from The Cancer Genome Atlas (TCGA) consortium. Results: Sixty of 106 EGFR -amplified glioblastomas were EGFRvIII-positive (56.6%). EGFRvIII positivity was not associated with different progression-free or overall survival. EGFRvIII status was unchanged at recurrence in 35 of 40 patients with EGFR -amplified primary tumors (87.5%). Four patients lost and one patient gained EGFRvIII positivity at recurrence. None of 33 EGFR- nonamplified glioblastomas acquired EGFR amplification or EGFRvIII at recurrence. EGFR SNVs were frequent in EGFR -amplified tumors, but were not linked to survival. Conclusions: EGFRvIII and EGFR SNVs are not prognostic in EGFR -amplified glioblastoma patients. EGFR amplification is retained in recurrent glioblastomas. Most EGFRvIII-positive glioblastomas maintain EGFRvIII positivity at recurrence. However, EGFRvIII expression may change in a subset of patients at recurrence, thus repeated biopsy with reassessment of EGFRvIII status is recommended for patients with recurrent glioblastoma to receive EGFRvIII-targeting agents. Clin Cancer Res; 23(22); 6846-55. ©2017 AACR . ©2017 American Association for Cancer Research.

  14. Electrochemistry and spectroelectrochemistry of tert-butylcalix[4]arene bridged bis double-decker lutetium(III) phthalocyanine, Lu2Pc4 and dimeric lutetium(III) phthalocyanine, Lu2Pc2(OAc)2

    International Nuclear Information System (INIS)

    Koca, Atif; Ceyhan, Tanju; Erbil, Mehmet K.; Ozkaya, Ali Riza; Bekaroglu, Ozer

    2007-01-01

    In this study, electrochemical, electrochromic and spectroelectrochemical properties of a tert-butylcalix[4]arene bridged bis double-decker lutetium(III) phthalocyanine (Lu 2 Pc 4 2) were investigated explicitly as compared with a tert-butylcalix[4]arene bridged dimeric lutetium(III) phthalocyanine [Lu 2 Pc 2 (OAc) 2 1]. Distinctive differences between electrochemical and electrochromic properties of 1 and 2 were detected. Moreover, the properties of 1 and 2 were compared with previously reported S 4 (CH 2 ) 4 bridged Lu 2 Pc 2 (OAc) 2 and Lu 2 Pc 4 . The calixarene bridged phthalocyanine (Pc) compounds, 1 and 2 showed well-defined electrochromic behaviour with green-blue and blue-purple colour transitions. The enhanced electrochromic properties of 2, as compared to 1, were attributed to its double-decker structure, probably allowing the formation of suitable ion channels for the counter ion movement in the solid film

  15. Intramolecular interactions in a new tris-dithizonatocobalt(III) complex

    International Nuclear Information System (INIS)

    Eschwege, Karel G. von; As, Lydia van; Joubert, Chris C.; Swarts, Jannie C.; Aquino, Manuel A.S.; Cameron, T. Stanley

    2013-01-01

    Graphical abstract: Electrochemically Co(HDz) 3 (5), show three main ligand-based redox processes, two reductions and one oxidation. Ligand oxidations can be resolved into three components highlighting effective intramolecular interactions between molecular fragments; a spectroelectrochemical study of (5) highlighted spectroscopic changes during the six observed redox steps. - Highlights: • Comparative CV's of dithizone (1), PhHg(HDz) and new Co(HDz) 3 (5), is discussed. • One oxidation and two reductions per ligand and a Co III/II couple for (5) are observed. • Mono- and tris-coordinated PhHg(HDz) and (5) have stable metal thioether bonds. • Crystal structure details explain good resolution between ligand redox processes. • Spectro-electrochemistry of (5) highlights spectroscopic properties of redox products. - Abstract: The reactions between dithizone (H 2 Dz (1)) or potassium dithizonate (KHDz (3)), and [Co(H 2 O) 6 ] 2+ (6), in acetone or methanol to liberate tris-dithizonatocobalt(III), Co(HDz) 3 (5), are described. The structure of (5) was confirmed by single crystal X-ray analyses and shows bidentate coordination to Co III via S and N donor atoms for all three HDz − ligands. A comparative voltammetric and spectro-electrochemical study revealed that (1) can be oxidised in two one-electron transfer steps, to generate a disulphide first and then HDz + . In contrast, upon complexation with cobalt, the free mercaptan group of (1) becomes a stable “metal thioether”, Co-S-C, which effectively prevents disulphide formation in all three ligands of (5) upon electrochemical oxidation. As a result, each ligand of Co(HDz) 3 shows just one oxidation process. Intramolecular communication between ligands is evident because the three separate ligand-based oxidations are well resolved. Two irreversible ligand reduction steps, each consisting of three unresolved components related to each of the three ligands, were also observed. The Co II /Co III couple

  16. International Working Group on Fast Reactors Thirteenth Annual Meeting. Summary Report. Part II

    International Nuclear Information System (INIS)

    1980-10-01

    The Thirteenth Annual Meeting of the IAEA International Working Group on Fast Reactors was held at the IAEA Headquarters, Vienna, Austria from 9 to 11 April 1980. The Summary Report (Part I) contains the Minutes of the Meeting. The Summary Report (Part II) contains the papers which review the national programme in the field of LMFBRs and other presentations at the Meeting. The Summary Report (Part III) contains the discussions on the review of the national programmes

  17. International Working Group on Fast Reactors Thirteenth Annual Meeting. Summary Report. Part I

    International Nuclear Information System (INIS)

    1980-09-01

    The Thirteenth Annual Meeting of the IAEA International Working Group on Fast Reactors was held at the IAEA Headquarters, Vienna, Austria from 9 to 11 April 1980. The Summary Report (Part I) contains the Minutes of the Meeting. The Summary Report (Part II) contains the papers which review the national programme in the field of LMFBRs and other presentations at the Meeting. The Summary Report (Part III) contains the discussions on the review of the national programmes

  18. Burnout in boiling heat transfer. Part III. High-quality forced-convection systems

    International Nuclear Information System (INIS)

    Bergles, A.E.

    1979-01-01

    This is the final part of a review of burnout during boiling heat transfer. The status of burnout in high-quality forced-convection systems is reviewed, and recent developments are summarized in detail. A general guide to the considerable literature is given. Parametric effects and correlations for water in circular and noncircular ducts are presented. Other topics discussed include transients, steam-generator applications, correlations for other fluids, fouling, and augmentation

  19. The SINTRAN III NODAL system

    International Nuclear Information System (INIS)

    Skaali, T.B.

    1980-10-01

    NODAL is a high level programming language based on FOCAL and SNOBOL4, with some influence from BASIC. The language was developed to operate on the computer network controlling the SPS accelerator at CERN. NODAL is an interpretive language designed for interactive use. This is the most important aspect of the language, and is reflected in its structure. The interactive facilities make it possible to write, debug and modify programs much faster than with compiler based languages like FORTRAN and ALGOL. Apart from a few minor modifications, the basic part of the Oslo University NODAL system does not differ from the CERN version. However, the Oslo University implementation has been expanded with new functions which enable the user to execute many of the SINTRAN III monitor calls from the NODAL level. In particular the most important RT monitor calls have been implemented in this way, a property which renders possible the use of NODAL as a RT program administrator. (JIW)

  20. Stark Broadening of Cr III Spectral Lines: DO White Dwarfs

    Directory of Open Access Journals (Sweden)

    Milan S. Dimitrijević

    2018-04-01

    Full Text Available Using the modified semiempirical method of Dimitrijević and Konjević, Stark widths have been calculated for six Cr III transitions, for an electron density of 10 17 cm ‒ 3 and for temperatures from 5000–80,000 K. Results have been used for the investigation of the influence of Stark broadening on spectral lines in cool DO white dwarf atmospheres. Calculated Stark widths will be implemented in the STARK-B database, which is also a part of the Virtual Atomic and Molecular Data Center (VAMDC.

  1. EFSUMB Guidelines on Interventional Ultrasound (INVUS), Part III - Abdominal Treatment Procedures (Long Version)

    DEFF Research Database (Denmark)

    Dietrich, Christoph F; Lorentzen, T.; Appelbaum, L.

    2016-01-01

    The third part of the European Federation of Societies for Ultrasound in Medicine and Biology (EFSUMB) Guidelines on Interventional Ultrasound (INVUS) assesses the evidence for ultrasound-guided and assisted interventions in abdominal treatment procedures. Recommendations for clinical practice ar...

  2. EFSUMB Guidelines on Interventional Ultrasound (INVUS), Part III - Abdominal Treatment Procedures (Short Version)

    DEFF Research Database (Denmark)

    Dietrich, Christoph F; Lorentzen, T.; Appelbaum, L.

    2016-01-01

    The third part of the European Federation of Societies for Ultrasound in Medicine and Biology (EFSUMB) Guidelines on Interventional Ultrasound assesses the evidence for ultrasound-guided and assisted interventions in abdominal treatment procedures. Recommendations for clinical practice are presen...

  3. Comparative Anti-Diabetic Evaluation of Different Parts of Himalrandia tetrasperma in Alloxan Induced Diabetic in Mice

    International Nuclear Information System (INIS)

    Ajaib, M.

    2016-01-01

    The present experiments were designed to investigate the acute effects of methanolic extracts of various parts of H. tetrasperma in diabetic mice. The basic phyto-chemical study showed the occurrence of alkaloids, saponins, flavonoids and tannins as main phyto-constituents in the methanolic extract. Diabetes was induced experimentally in mice by intra peritoneally injecting alloxan (150 mg/kg i.p.). In acute study, methanolic H. tetrasperma extracts of various parts of plant were evaluated for anti-diabetic potential in alloxan induced diabetic mice. Extracts of leaves, bark and seeds (250 mg/kg, i.p) and metformin (250 mg/kg i.p) were given intra peritoneal in alloxan treated diabetic mice and blood glucose levels were measured at 0, 360 and 24 h. There was significant lowering of blood glucose level at 1 h after treatment, in diabetic mice treated with methanolic extracts of bark (182.3 ± 3.6 mg/dL), leaves (178.5 ± 1.2 mg/dL) and seeds (156.3 ± 11.3 mg/dL) when compared with control diabetic group (280 ± 7.92 mg/dL). Highly significant results were also obtained at 24 h after treatment with methanolic extracts of bark (187.67 ±1.2 mg/dL), leaves (170.66 ± 2.3 mg/dL) and seeds (142 ± 8.7 mg/dL) when compared with control diabetic group (257.7 ± 6.7 mg/dL). It is concluded that methanolic extract of all parts possess significant anti-diabetic activity which is due to the presence of phytochemicals, i.e. alkaloids, flavonoids, phenols, saponins, tannins and it can be further evaluated for the mechanism involved. (author)

  4. Thermodynamic model for solution behavior and solid-liquid equilibrium in Na-Al(III)-Fe(III)-Cr(III)-Cl-H2O system at 25°C

    Science.gov (United States)

    André, Laurent; Christov, Christomir; Lassin, Arnault; Azaroual, Mohamed

    2018-03-01

    The knowledge of the thermodynamic behavior of multicomponent aqueous electrolyte systems is of main interest in geo-, and environmental-sciences. The main objective of this study is the development of a high accuracy thermodynamic model for solution behavior, and highly soluble M(III)Cl3(s) (M= Al, Fe, Cr) minerals solubility in Na-Al(III)-Cr(III)-Fe(III)-Cl-H2O system at 25°C. Comprehensive thermodynamic models that accurately predict aluminium, chromium and iron aqueous chemistry and M(III) mineral solubilities as a function of pH, solution composition and concentration are critical for understanding many important geochemical and environmental processes involving these metals (e.g., mineral dissolution/alteration, rock formation, changes in rock permeability and fluid flow, soil formation, mass transport, toxic M(III) remediation). Such a model would also have many industrial applications (e.g., aluminium, chromium and iron production, and their corrosion, solve scaling problems in geothermal energy and oil production). Comparisons of solubility and activity calculations with the experimental data in binary and ternary systems indicate that model predictions are within the uncertainty of the data. Limitations of the model due to data insufficiencies are discussed. The solubility modeling approach, implemented to the Pitzer specific interaction equations is employed. The resulting parameterization was developed for the geochemical Pitzer formalism based PHREEQC database.

  5. Timely management of developing class III malocclusion

    Directory of Open Access Journals (Sweden)

    M R Yelampalli

    2012-01-01

    Full Text Available Timing of orthodontic treatment, especially for children with developing class III malocclusions, has always been somewhat controversial, and definitive treatment tends to be delayed for severe class III cases. Developing class III patients with moderate to severe anterior crossbite and deep bite may need early intervention in some selected cases. Class III malocclusion may develop in children as a result of an inherent growth abnormality, i.e. true class III malocclusion, or as a result of premature occlusal contacts causing forward functional shift of the mandible, which is known as pseudo class III malocclusion. These cases, if not treated at the initial stage of development, interfere with normal growth of the jaw bases and may result in severe facial deformities. The treatment should be carried out as early as possible for permitting normal growth of the skeletal bases. This paper deals with the selection of an appropriate appliance from the various current options available for early intervention in developing class III malocclusion through two case reports.

  6. Octachloro- And Octabromoditechnetate(III) And Their Rhenium(III) Congeners

    International Nuclear Information System (INIS)

    Poineau, F.; Sattelberger, A.P.; Conradson, S.D.; Czerwinski, K.R.

    2008-01-01

    The compound (n-Bu 4 N) 2 Tc 2 Br 8 was prepared by the metathesis of (n-Bu 4 N) 2 Tc 2 Cl 8 with HBr (g) in dichloromethane and characterized by X-ray absorption fine structure spectroscopy and UV-vis spectroscopy. Analysis of the data gives a Tc-Tc distance of 2.16(1) (angstrom) and a Tc-Br distance of 2.48(1) (angstrom). The Tc(III) oxidation state was inferred by the position of the edge absorption, which reveals a shift of 12 eV between (n-Bu 4 N) 2 Tc 2 Br 8 and NH 4 TcO 4 . The analogous shift between (n-Bu 4 N) 2 Tc 2 Cl 8 and NH 4 TcO 4 is 11 eV. The UV-vis spectrum of Tc 2 Br 8 2- in dichloromethane exhibits the characteristic (delta) → (delta)* transition at 13717 cm -1 . The M 2 X 8 2- (M = Re, Tc; X = Cl, Br) UV-vis spectra are compared, and the position of the (delta) → (delta)* transition discussed

  7. A Modified Edge Crack Torsion Test for Measurement of Mode III Fracture Toughness of Laminated Tape Composites

    Science.gov (United States)

    Czabaj, Michael W.; Davidson, Barry D.; Ratcliffe, James G.

    2016-01-01

    Modifications to the edge crack torsion (ECT) test are studied to improve the reliability of this test for measuring the mode-III fracture toughness, G (sub IIIc), of laminated tape fiber-reinforced polymeric (FRP) composites. First, the data reduction methods currently used in the ECT test are evaluated and deficiencies in their accuracy are discussed. An alternative data reduction technique, which uses a polynomial form to represent ECT specimen compliance solution, is evaluated and compared to FEA (finite element analysis) results. Second, seven batches of ECT specimens are tested, each batch containing specimens with a preimplanted midplane edge delamination and midplane plies with orientations of plus theta divided by minus theta, with theta ranging from 0 degrees to 90 degrees in 15-degree increments. Tests on these specimens show that intralaminar cracking occurs in specimens from all batches except for which theta = 15 degrees and 30 degrees. Tests on specimens of these two batches are shown to result in mode-III delamination growth at the intended ply interface. The findings from this study are encouraging steps towards the use of the ECT test as a standardized method for measuring G (sub IIIc), although further modification to the data reduction method is required to make it suitable for use as part of a standardized test method.

  8. Comparative ligational, optical band gap and biological studies on Cr(III) and Fe(III) complexes of hydrazones derived from 2-hydrazinyl-2-oxo-N-phenylacetamide with both vanillin and O-vanillin

    Science.gov (United States)

    Yousef, T. A.; Abu El-Reash, G. M.; Attia, M. I.; El-Tabai, M. N.

    2015-09-01

    The Cr(III) and Fe(III) complexes of hydrazones derived from the condensation of 2-hydrazinyl-2-oxo-N-phenylacetamide with both vanillin and o-vanillin synthesized and characterized by different conventional physicochemical techniques. The kinetic and thermodynamic parameters for the different decomposition steps were calculated using Coats-Redfern and Horowitz-Metzger equations. The bond lengths, bond angles, HOMO, LUMO, dipole moment and binding energy calculated by DFT calculations. The optical band gap (Eg) values equal 3.28, 3.03, 3.58 and 3.57 eV for [Cr(HL1)Cl2(H2O)2](0.75H2O), [Cr(HL2)Cl2(H2O)](H2O), [Fe(HL1)Cl2(H2O)2](0.5H2O) and [Fe(HL2)2Cl(H2O)](3H2O) complexes, respectively. The antibacterial activities tested against Bacillus subtilis and Escherichia coli bacteria.

  9. Enhanced Cr(VI) reduction and As(III) oxidation in ice phase: Important role of dissolved organic matter from biochar

    Energy Technology Data Exchange (ETDEWEB)

    Dong, Xiaoling [Department of Soil and Water Science, University of Florida, Gainesville, FL 32611 (United States); Ma, Lena Q., E-mail: lqma@ufl.edu [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Jiangsu 210046 (China); Department of Soil and Water Science, University of Florida, Gainesville, FL 32611 (United States); Gress, Julia; Harris, Willie [Department of Soil and Water Science, University of Florida, Gainesville, FL 32611 (United States); Li, Yuncong [Soil and Water Science Department, Tropical Research and Education Center, University of Florida, Homestead, FL 33031-3314 (United States)

    2014-02-01

    Graphical abstract: - Highlights: • Biochar-derived dissolved organic matter (DOM) effectively reduced Cr(VI) and oxidized As(III). • Cr(VI) and As(III) could serve as a redox couple. • Cr(VI) and As(III) redox conversion was more effective in the ice phase than aqueous phase. • FTIR and ESR showed that biochar DOM served as both electron donor and acceptor. - Abstract: This study evaluated the impact of DOM from two biochars (sugar beet tailing and Brazilian pepper) on Cr(VI) reduction and As(III) oxidation in both ice and aqueous phases with a soil DOM as control. Increasing DOM concentration from 3 to 300 mg C L{sup −1} enhanced Cr(VI) reduction from 20% to 100% and As(III) oxidation from 6.2% to 25%; however, Cr(VI) reduction decreased from 80–86% to negligible while As(III) oxidation increased from negligible to 18–19% with increasing pH from 2 to 10. Electron spin resonance study suggested semiquinone radicals in DOM were involved in As(III) oxidation while Fourier transform infrared analysis suggested that carboxylic groups in DOM participated in both Cr(VI) reduction and As(III) oxidation. During Cr(VI) reduction, part of DOM (∼10%) was oxidized to CO{sub 2}. The enhanced conversion of Cr(VI) and As(III) in the ice phase was due to the freeze concentration effect with elevated concentrations of electron donors and electron acceptors in the grain boundary. Though DOM enhanced both Cr(VI) reduction and As(III)oxidation, Cr(VI) reduction coupled with As(III) oxidation occurred in absence of DOM. The role of DOM, Cr(VI) and/or As(III) in Cr and As transformation may provide new insights into their speciation and toxicity in cold regions.

  10. Combustion chemistry and flame structure of furan group biofuels using molecular-beam mass spectrometry and gas chromatography - Part III: 2,5-Dimethylfuran.

    Science.gov (United States)

    Togbé, Casimir; Tran, Luc-Sy; Liu, Dong; Felsmann, Daniel; Oßwald, Patrick; Glaude, Pierre-Alexandre; Sirjean, Baptiste; Fournet, René; Battin-Leclerc, Frédérique; Kohse-Höinghaus, Katharina

    2014-03-01

    This work is the third part of a study focusing on the combustion chemistry and flame structure of furan and selected alkylated derivatives, i.e. furan in Part I, 2-methylfuran (MF) in Part II, and 2,5-dimethylfuran (DMF) in the present work. Two premixed low-pressure (20 and 40 mbar) flat argon-diluted (50%) flames of DMF were studied with electron-ionization molecular-beam mass spectrometry (EI-MBMS) and gas chromatography (GC) under two equivalence ratios (φ=1.0 and 1.7). Mole fractions of reactants, products, and stable and radical intermediates were measured as a function of the distance to the burner. Kinetic modeling was performed using a reaction mechanism that was further developed in the present series, including Part I and Part II. A reasonable agreement between the present experimental results and the simulation is observed. The main reaction pathways of DMF consumption were derived from a reaction flow analysis. Also, a comparison of the key features for the three flames is presented, as well as a comparison between these flames of furanic compounds and those of other fuels. An a priori surprising ability of DMF to form soot precursors (e.g. 1,3-cyclopentadiene or benzene) compared to less substituted furans and to other fuels has been experimentally observed and is well explained in the model.

  11. Hybrid III-V/silicon lasers

    Science.gov (United States)

    Kaspar, P.; Jany, C.; Le Liepvre, A.; Accard, A.; Lamponi, M.; Make, D.; Levaufre, G.; Girard, N.; Lelarge, F.; Shen, A.; Charbonnier, P.; Mallecot, F.; Duan, G.-H.; Gentner, J.-.; Fedeli, J.-M.; Olivier, S.; Descos, A.; Ben Bakir, B.; Messaoudene, S.; Bordel, D.; Malhouitre, S.; Kopp, C.; Menezo, S.

    2014-05-01

    The lack of potent integrated light emitters is one of the bottlenecks that have so far hindered the silicon photonics platform from revolutionizing the communication market. Photonic circuits with integrated light sources have the potential to address a wide range of applications from short-distance data communication to long-haul optical transmission. Notably, the integration of lasers would allow saving large assembly costs and reduce the footprint of optoelectronic products by combining photonic and microelectronic functionalities on a single chip. Since silicon and germanium-based sources are still in their infancy, hybrid approaches using III-V semiconductor materials are currently pursued by several research laboratories in academia as well as in industry. In this paper we review recent developments of hybrid III-V/silicon lasers and discuss the advantages and drawbacks of several integration schemes. The integration approach followed in our laboratory makes use of wafer-bonded III-V material on structured silicon-on-insulator substrates and is based on adiabatic mode transfers between silicon and III-V waveguides. We will highlight some of the most interesting results from devices such as wavelength-tunable lasers and AWG lasers. The good performance demonstrates that an efficient mode transfer can be achieved between III-V and silicon waveguides and encourages further research efforts in this direction.

  12. Use of Fe(III) oxalate for oxidativewastewater treatment; Einsatz von Fe(III)-Oxalat zur chemisch-oxidativen Abwasserbehandlung

    Energy Technology Data Exchange (ETDEWEB)

    Kim, S.M.; Vogelpohl, A. [Clausthal Univ., Clausthal-Zellerfeld (Germany). Inst. fuer Thermische Verfahrenstechnik

    1998-08-01

    Iron(III)-oxalate was used as an iron catalyst for the Photo Fenton reaction. Iron(III) oxalations ([Fe(C{sub 2}O{sub 4}){sub 3}]{sup 3-}) are reduced to Fe(II) by irradiation using near UV-light ({lambda} = 300 - 400 nm) or visible light ({lambda} > 400 nm). At the same time, CO{sub 2}{sup -} or C{sub 2}O{sub 4}{sup -}-radicals originate, which cause the secondary reduction of Fe(III) to Fe(II). By means of the photolytically regenerated Fe(II) ions, hydroxyl radicals are increasingly formed, so that the degradation of organic substances is accelerated. The work aimed to assess the catalytic effect of Fe(III) oxalate for photochemical oxidation processes and to establish the parameters influencing further treatment of leachate from a municipal waste sanitary landfill by means of technical-scale experiments. (orig.) [Deutsch] In der vorliegenden Arbeit wurde Eisen(III)-Oxalat als Eisenkatalysator fuer die Photo-Fenton-Reaktion eingesetzt. Eisen(III)-Oxalationen ([Fe(C{sub 2}O{sub 4}){sub 3}]{sup 3-}) werden durch Strahlung mit nahem UV-Licht ({lambda}=300 bis 400 nm) oder mit sichtbarem Licht ({lambda}>400 nm) zu Fe(II) reduziert. Gleichzeitig entstehen CO{sub 2}{sup .-} oder C{sub 2}O{sub 4}{sup .-}-Radikale, die eine sekundaere Reduktion von Fe(III) zu Fe(II) bewirken. Mit Hilfe der photolytiisch regenerierten Fe(II)-Ionen werden vermehrt Hydroxylradikale gebildet und damit die Abbaugeschwindigkeit der organischen Substanzen beschleunigt. Ziel der hier vorgestellten Arbeit war es, die katalytische Wirkung von Fe(III)-Oxalat fuer photochemische Oxidationsverfahren abzuschaetzen und die Einflussparameter zur weitergehenden Behandlung eines Deponiesickerwassers aus Hausmuelldeponie anhand von Technikumsversuchen zu ermitteln. (orig.)

  13. Banded versus Single-sided bonded space maintainers: A Comparative Study

    Directory of Open Access Journals (Sweden)

    Sudhir Mittal

    2018-01-01

    Full Text Available Background: The present study is conducted to evaluate and compare the clinical performance of conventional band and loop space maintainer and fiber reinforced composite resin (FRCR space maintainers. Materials and Methods: A total of 45 extraction sites in the age group of 6–9 years having premature loss of primary molars or indicated for extraction were selected for the study. The patients were randomly divided into three groups as Group I, in which conventional band and loop space maintainer was given, Group II and Group III (FRCR, in which FRCR (everStick CandB and impregnated glass fibers (Interlig space maintainers were given, respectively. Patients were recalled at 3, 6, and 12-month interval for evaluation of all the three types of space maintainer. Results: Overall success rate of Group I was 86.7%, for Group II was 80%, and for Group III was 73.3% at the end of the study. Patient acceptability was significantly higher in Group II and Group III (FRCR as compared to Group I (Conventional band and loop. In Group I, cement loss and fracture of loop, whereas in Group II and Group III, debonding at enamel composite was the most common failure followed by debonding at fiber composite and fiber fracture. FRCR space maintainers were found to be cost-effective as compared to Group I. More linear changes and angular changes were recorded in Group I as compared to Group II and Group III but difference was not significant (P > 0.05. Conclusion: Only single (buccal surface application of FRCR space maintainers showed almost equal clinical efficacy compared to conventional band and loop space maintainer with significantly better patient acceptability, less cost, and time taken.

  14. Synthesis of Er(III)/Yb(III)-doped BiF3 upconversion nanoparticles for use in optical thermometry.

    Science.gov (United States)

    Du, Peng; Yu, Jae Su

    2018-03-23

    The authors describe an ethylene glycol assisted precipitation method for synthesis of Er(III)/Yb(III)-doped BiF 3 nanoparticles (NPs) at room temperature. Under 980-nm light irradiation, the NPs emit upconversion (UC) emission of Er(III) ions as a result of a two-photon absorption process. The temperature-dependent green emissions (peaking at 525 and 545 nm) are used to establish an unambiguous relationship between the ratio of fluorescence intensities and temperature. The NPs have a maximum sensitivity of 6.5 × 10 -3  K -1 at 619 K and can be applied over the 291-691 K temperature range. The results indicate that these NPs are a promising candidate for optical thermometry. Graphical abstract Schematic of the room-temperature preparation of Er(III)/Yb(III)-doped BiF 3 nanoparticles with strongly temperature-dependent upconversion emission.

  15. Heterogeneous FDG-guided dose-escalation for locally advanced NSCLC (the NARLAL2 trial): Design and early dosimetric results of a randomized, multi-centre phase-III study

    DEFF Research Database (Denmark)

    Møller, Ditte Sloth; Nielsen, Tine Bjørn; Brink, Carsten

    2017-01-01

    Background and purpose: Local recurrence is frequent in locally advanced NSCLC and is primarily located in FDG-avid parts of tumour and lymph nodes. Aiming at improving local control without increasing toxicity, we designed a multi-centre phase-III trial delivering inhomogeneous dose-escalation d......Background and purpose: Local recurrence is frequent in locally advanced NSCLC and is primarily located in FDG-avid parts of tumour and lymph nodes. Aiming at improving local control without increasing toxicity, we designed a multi-centre phase-III trial delivering inhomogeneous dose...

  16. Liquid plugs bouncing against a solid basis, comparison of SIMMER-III and PLEXUS results

    International Nuclear Information System (INIS)

    Maschek, W.; Arnecke, G.; Flad, M.

    1995-01-01

    The SIMMER III code is being tested by application to problems of reactor accidents. The fluid dynamics/thermohydraulics part of the code can be applied also to evaporation/condensation, melt, and freezing phenomena. For a liquid plug bouncing against a solid basis, the momentum transfer is calculated. PLEXUS results turn out to be in significant disagreement with the SIMMER calculations. (orig.)

  17. Studies of Binary Complexes of Tripodal Ligand cis,cis-1,3,5-tris(methylaminocyclohexane with Cr(III and Fe(III

    Directory of Open Access Journals (Sweden)

    S. Esakki Muthu

    2005-01-01

    Full Text Available The formation of binary complexes of Cr(III and Fe(III with a tripodal ligand cis,cis-1,3,5-tris(methylaminocyclohexane (tmach (L has been investigated in solution. The overall stability constants of tmach with Cr(III and Fe(III were determined by potentiometric method at an ionic strength of 0.1 M NaClO4 at 25±1°C in aqueous medium. The formation of species like MLH25+, MLH4+, ML3+, ML(OH2+ and ML(OH3 were observed. Fe(III was found to form more stable complexes than Cr(III. Molecular mechanics calculations were performed to explain the mode of coordination in solution.

  18. Mechanisms for Fe(III) oxide reduction in sedimentary environments

    Science.gov (United States)

    Nevin, Kelly P.; Lovely, Derek R.

    2002-01-01

    Although it was previously considered that Fe(III)-reducing microorganisms must come into direct contact with Fe(III) oxides in order to reduce them, recent studies have suggested that electron-shuttling compounds and/or Fe(III) chelators, either naturally present or produced by the Fe(III)-reducing microorganisms themselves, may alleviate the need for the Fe(III) reducers to establish direct contact with Fe(III) oxides. Studies with Shewanella alga strain BrY and Fe(III) oxides sequestered within microporous beads demonstrated for the first time that this organism releases a compound(s) that permits electron transfer to Fe(III) oxides which the organism cannot directly contact. Furthermore, as much as 450 w M dissolved Fe(III) was detected in cultures of S. alga growing in Fe(III) oxide medium, suggesting that this organism releases compounds that can solublize Fe(III) from Fe(III) oxide. These results contrast with previous studies, which demonstrated that Geobacter metallireducens does not produce electron-shuttles or Fe(III) chelators. Some freshwater aquatic sediments and groundwaters contained compounds, which could act as electron shuttles by accepting electrons from G. metallireducens and then transferring the electrons to Fe(III). However, other samples lacked significant electron-shuttling capacity. Spectroscopic studies indicated that the electron-shuttling capacity of the waters was not only associated with the presence of humic substances, but water extracts of walnut, oak, and maple leaves contained electron-shuttling compounds did not appear to be humic substances. Porewater from a freshwater aquatic sediment and groundwater from a petroleum-contaminated aquifer contained dissolved Fe(III) (4-16 w M), suggesting that soluble Fe(III) may be available as an electron acceptor in some sedimentary environments. These results demonstrate that in order to accurately model the mechanisms for Fe(III) reduction in sedimentary environments it will be necessary

  19. Reversed phase partition chromatographic separation of Gd(III) on poly(Crown Ether) column

    International Nuclear Information System (INIS)

    Mahanwar, K.R.; Sabale, S.R.

    2014-01-01

    A simple method has been developed for the separation of Gd(III) in hippuric acid medium by using poly(dibenzo-18-crown-6) as stationary phase. The effect of hippuric acid concentration, different eluting agent, foreign ions etc was studied and the optimum conditions were established. Breakthrough capacity of poly(dibenzo-18-crown-6) for Gd(III) was found to be 0.572 ±0.01 mmolg -1 of crown polymer. The separation of Gd(III) from other elements in multicomponent mixtures has been achieved. The method was extended for determination of Gd(III) in real sample. The method is simple, rapid and selective with good reproducibility (approximately ± 2%). Crown ethers are widely used as complexing agent that can selectively capture metal cation in their cavity. This special feature shown by poly (dibenzo-18-crown-6) has been used in our laboratory for selective cation exchanger by column chromatography. No attempts were made for the separation of Gd(III) using hippuric acid media and column chromatography. The present communication describes a simple and sensitive method for the determination of Gd(III) using poly(dibenzo-18-crown-6) as stationary phase in hippuric acid medium. The proposed method affords an attractive feature as compared to the solvent extraction technique i.e. it is free from any organic diluents as an environmental concern

  20. Apolipoprotein C-II and C-III metabolism in a kindred of familial hypobetalipoproteinemia

    International Nuclear Information System (INIS)

    Malmendier, C.L.; Delcroix, C.; Lontie, J.F.; Dubois, D.Y.

    1991-01-01

    Three affected members of a kindred with asymptomatic hypobetalipoproteinemia (HBL) showed low levels of triglycerides, low-density lipoprotein (LDL)-cholesterol, and apolipoproteins (apo) B, C-II, and C-III. Turnover of iodine-labeled apo C-II and apo C-III associated in vitro to plasma lipoproteins was studied after intravenous injection. Radioactivity in plasma and lipoproteins (95% recovered in high-density lipoprotein [HDL] density range) and in 24-hour urine samples was observed for 16 days. A parallelism of the slowest slopes of plasma decay curves was observed between apo C-II and apo C-III, indicating a partial common catabolic route. Urine/plasma radioactivity ratio (U/P) varied with time, suggesting heterogeneity of metabolic pathways. A new compartmental model using the SAAM program was built, not only fitting simultaneously plasma and urine data, but also taking into account the partial common metabolism of lipoprotein particles (LP) containing apo C-II and apo C-III. The low apo C-II and C-III plasma concentrations observed in HBL compared with normal resulted from both an increased catabolism and a reduced synthesis, these changes being more marked for apo C-III. The modifications in the rate constants of the different pathways calculated from the new model are in favor of an increased direct removal of particles following the fast pathway, likely in the very-low-density lipoprotein (VLDL) density range

  1. Effects of ionic strength on the coordination of Eu(III) and Cm(III) to a Gram-negative bacterium, Paracoccus denitrificans

    International Nuclear Information System (INIS)

    Ozaki, T.; Ohnuki, T.; Kimura, T.; Francis, A.J.

    2006-01-01

    We studied the effect of ionic strength on the interactions of Europium(III) and Curium(III) with a Gram-negative bacterium Paracoccus denitrificans. Bacterial cells grown in 0.5-, 3.5-, and 5.0% NaCl were used in adsorption experiments and laser experiments that were performed at the same ionic strengths as those in the original growth media. The distribution ratio (log K d ) for Eu(III) and Cm(III) was determined at pHs 3-5. To elucidate the coordination environment of Eu(III) adsorbed on P. denitrificans, we estimated the number of water molecules in the inner sphere and strength of the ligand field by time-resolved laser-induced fluorescence spectroscopy (TRLFS) at pHs 4-6. The log K d of Eu(III) and Cm(III) increased with an increase of pH at all ionic strengths because there was less competition for ligands in cells with H + at higher pHs, wherein less H + was present in solution: cation adsorption generally occurs through an exchange with H + on the functional groups of coordination sites. No significant differences were observed in the log K d of Eu(III) and Cm(III) at each pH in 0.5-, 3.5-, and 5.0% NaCl solutions, though competition for ligands with Na + would be expected to increase at higher NaCl concentrations. The log K d of Eu(III) was almost equivalent to that of Cm(III) under all the experimental conditions. TRLFS showed that the coordination environments of Eu(III) did not differ from each other at 0.5-, 3.5-, and 5.0% NaCl at pHs 4-6. TRLFS also showed that the characteristic of the coordination environment of Eu(III) on P. denitrificans was similar to that on a halophile, Nesterenkonia halobia, while it significantly differed from that on a non-halophile, Pseudomonas putida. These findings indicate that the number of coordination sites for Eu(III) on P. denitrificans, whose cell surface may have similar structures to that of halophiles, increased with increasing ionic strength, though their structure remained unchanged. (orig.)

  2. Optical and Temporal Carrier Dynamics Investigations of III-Nitrides for Semiconductor Lighting

    KAUST Repository

    Ajia, Idris A.

    2018-01-01

    In the first part of this dissertation, the effects of some important types of crystal defects present in III-nitride structures are investigated. Here, two types of defects are studied in two different III-nitride-based light emitting structures. The first defects of interest are V-pit defects in InGaN/GaN multiple quantum well (MQW) blue LEDs, where their contribution to the high-efficiency of such LEDs is discussed. In addition, the effect of these defects on the efficiency droop phenomenon in these LEDs is elucidated. Secondly, the optical effects of grain boundary defects in AlN-rich AlGaN/AlGaN MQWs is studied. In this study, it is shown that grain boundary defects may result in abnormal carrier localization behavior in these deep ultraviolet (UV) structures. While both defects are treated individually, it is evident from these studies that threading dislocation (TD) defects are an underlying contributor to the more undesirable outcomes of the said defects. In the second part, the dissertation reports on the carrier dynamics of III-nitride LED structures grown on emerging substrates—as possible efficiency enhancing techniques—aimed at mitigating the effects of TD defects. Thus, the carrier dynamics of GaN/AlGaN UV MQWs grown, for the first time, on (2̅01) – oriented β-Ga2O3 is studied. It is shown to be a candidate substrate for highly efficient vertical UV devices. Finally, results from the carrier dynamics investigation of an AlGaN/AlGaN MQW LED structure homoepitaxially grown on AlN substrate are discussed, where it is shown that its high-efficiency is sustained at high temperatures through the thermal redistribution of carriers to highly efficient recombination sites.

  3. Specific Reagent for Cr(III): Imaging Cellular Uptake of Cr(III) in Hct116 Cells and Theoretical Rationalization.

    Science.gov (United States)

    Ali, Firoj; Saha, Sukdeb; Maity, Arunava; Taye, Nandaraj; Si, Mrinal Kanti; Suresh, E; Ganguly, Bishwajit; Chattopadhyay, Samit; Das, Amitava

    2015-10-15

    A new rhodamine-based reagent (L1), trapped inside the micellar structure of biologically benign Triton-X 100, could be used for specific recognition of Cr(III) in aqueous buffer medium having physiological pH. This visible light excitable reagent on selective binding to Cr(III) resulted in a strong fluorescence turn-on response with a maximum at ∼583 nm and tail of that luminescence band extended until 650 nm, an optical response that is desired for avoiding the cellular autofluorescence. Interference studies confirm that other metal ions do not interfere with the detection process of Cr(III) in aqueous buffer medium having pH 7.2. To examine the nature of binding of Cr(III) to L1, various spectroscopic studies are performed with the model reagent L2, which tend to support Cr(III)-η(2)-olefin π-interactions involving two olefin bonds in molecular probe L1. Computational studies are also performed with another model reagent LM to examine the possibility of such Cr(III)-η(2)-olefin π-interactions. Presumably, polar functional groups of the model reagent LM upon coordination to the Cr(III) center effectively reduce the formal charge on the metal ion and this is further substantiated by results of the theoretical studies. This assembly is found to be cell membrane permeable and shows insignificant toxicity toward live colon cancer cells (Hct116). Confocal laser scanning microscopic studies further revealed that the reagent L1 could be used as an imaging reagent for detection of cellular uptake of Cr(III) in pure aqueous buffer medium by Hct116 cells. Examples of a specific reagent for paramagnetic Cr(III) with luminescence ON response are scanty in the contemporary literature. This ligand design helped us in achieving the turn on response by utilizing the conversion from spirolactam to an acyclic xanthene form on coordination to Cr(III).

  4. THE IMPACT OF NEW REGULATION ON FOUR EUROPEAN BANKING SYSTEMS. A BASEL III APPROACH

    Directory of Open Access Journals (Sweden)

    Anamaria AVADANEI

    2013-12-01

    Full Text Available One of the solutions designed to rebuild the banking system is the reconfiguration of the regulatory framework. Still active, the episodes of liquidity shortage and bank failure ask for solid measures in order to increase the solidity of individual institutions, to protect the financial stability of the banking systems and to maintain confidence on the markets. The aim of this paper is to analyze the situation of four European banking systems (Czech Republic, Poland, Romania and Croatia in terms of Basel III standards. Structured on three parts, the study points out the real concerns regarding Basel III effectiveness; analyzes the evolutions of capital, leverage and liquidity indicators and highlights the future possible scenarios/actions for aligning to the new regulation. To conclude, we determine the white and the black spots of the selected banking systems related to Basel III implementation. The results show good levels of capital in Poland, Czech Republic, Croatia and Romania, and some liquidity issues in Poland. The Czech and the Croatian banking systems are the best prepared for shocks.

  5. III-Nitride Blue Laser Diode with Photoelectrochemically Etched Current Aperture

    Science.gov (United States)

    Megalini, Ludovico

    distance. In this dissertation it is presented the first nitride blue edge emitting LD with a photoelectrochemical etched current aperture (CA-LD) into the device active region. Photoelectrochemical etching (PECE) has emerged as a powerful wet etching technique for III-nitride compounds. Beyond the advantages of wet etching technique, PECE offers bandgap selectivity, which is particularly desirable because it allows more freedom in designing new and advanced devices with higher performances. In the first part of this thesis a review of PECE is presented, and it is shown how it can be used to achieve a selective and controllable deep undercut of the active region of LEDs and LDs, in particular the selective PECE of MQW active region of (10-10) m-plane and (20-2-1) plane structures is reported. In the second part of this thesis, the fabrication flow process of the CA-LD is described. The performance of these devices is compared with that of shallow etched ridge LDs with a nominally identical epitaxial structure and active region width and it is experimentally shown that the CA-LD design has superior performance. CW operation of a (20-2-1) CA-LD with a 1.5 microm wide active region is demonstrated. Finally, in the third and last part of this thesis, the CA-LD performance is discussed in more details, in particular, an analysis of optical scattering losses caused by the rough edges of the remnant PEC etched active region is presented.

  6. Constitutive expression of the xylanase inhibitor TAXI-III delays Fusarium head blight symptoms in durum wheat transgenic plants.

    Science.gov (United States)

    Moscetti, Ilaria; Tundo, Silvio; Janni, Michela; Sella, Luca; Gazzetti, Katia; Tauzin, Alexandra; Giardina, Thierry; Masci, Stefania; Favaron, Francesco; D'Ovidio, Renato

    2013-12-01

    Cereals contain xylanase inhibitor (XI) proteins which inhibit microbial xylanases and are considered part of the defense mechanisms to counteract microbial pathogens. Nevertheless, in planta evidence for this role has not been reported yet. Therefore, we produced a number of transgenic plants constitutively overexpressing TAXI-III, a member of the TAXI type XI that is induced by pathogen infection. Results showed that TAXI-III endows the transgenic wheat with new inhibition capacities. We also showed that TAXI-III is correctly secreted into the apoplast and possesses the expected inhibition parameters against microbial xylanases. The new inhibition properties of the transgenic plants correlate with a significant delay of Fusarium head blight disease symptoms caused by Fusarium graminearum but do not significantly influence leaf spot symptoms caused by Bipolaris sorokiniana. We showed that this contrasting result can be due to the different capacity of TAXI-III to inhibit the xylanase activity of these two fungal pathogens. These results provide, for the first time, clear evidence in planta that XI are involved in plant defense against fungal pathogens and show the potential to manipulate TAXI-III accumulation to improve wheat resistance against F. graminearum.

  7. Computation-based virtual screening for designing novel antimalarial drugs by targeting falcipain-III: a structure-based drug designing approach.

    Science.gov (United States)

    Kesharwani, Rajesh Kumar; Singh, Durg Vijay; Misra, Krishna

    2013-01-01

    Cysteine proteases (falcipains), a papain-family of enzymes of Plasmodium falciparum, are responsible for haemoglobin degradation and thus necessary for its survival during asexual life cycle phase inside the human red blood cells while remaining non-functional for the human body. Therefore, these can act as potential targets for designing antimalarial drugs. The P. falciparum cysteine proteases, falcipain-II and falcipain- III are the enzymes which initiate the haemoglobin degradation, therefore, have been selected as targets. In the present study, we have designed new leupeptin analogues and subjected to virtual screening using Glide at the active site cavity of falcipain-II and falcipain-III to select the best docked analogues on the basis of Glide score and also compare with the result of AutoDock. The proposed analogues can be synthesized and tested in vivo as future potent antimalarial drugs. Protein falcipain-II and falcipain-III together with bounds inhibitors epoxysuccinate E64 (E64) and leupeptin respectively were retrieved from protein data bank (PDB) and latter leupeptin was used as lead molecule to design new analogues by using Ligbuilder software and refined the molecules on the basis of Lipinski rule of five and fitness score parameters. All the designed leupeptin analogues were screened via docking simulation at the active site cavity of falcipain-II and falcipain-III by using Glide software and AutoDock. The 104 new leupeptin-based antimalarial ligands were designed using structure-based drug designing approach with the help of Ligbuilder and subjected for virtual screening via docking simulation method against falcipain-II and falcipain-III receptor proteins. The Glide docking results suggest that the ligands namely result_037 shows good binding and other two, result_044 and result_042 show nearly similar binding than naturally occurring PDB bound ligand E64 against falcipain-II and in case of falcipain-III, 15 designed leupeptin analogues having

  8. Validation of the Serpent 2-DYNSUB code sequence using the Special Power Excursion Reactor Test III (SPERT III)

    International Nuclear Information System (INIS)

    Knebel, Miriam; Mercatali, Luigi; Sanchez, Victor; Stieglitz, Robert; Macian-Juan, Rafael

    2016-01-01

    Highlights: • Full few-group cross section tables created by Monte Carlo lattice code Serpent 2. • Serpent 2 group constant methodology verified for HFP static and transient cases. • Serpent 2-DYNSUB tool chainvalidated using SPERT III REA experiments. • Serpent 2-DYNSUB tool chain suitable to model RIAs in PWRs. - Abstract: The Special Power Excursion Reactor Test III (SPERT III) is studied using the Serpent 2-DYNSUB code sequence in order to validate it for modeling reactivity insertion accidents (RIA) in PWRs. The SPERT III E-core was a thermal research reactor constructed to analyze reactor dynamics. Its configuration resembles a commercial PWR on terms of fuel type, choice of moderator, coolant flow and system pressure. The initial conditions of the rod ejection accident experiments (REA) performed cover cold startup, hot startup, hot standby and operating power scenarios. Eight of these experiments were analyzed in detail. Firstly, multi-dimensional nodal diffusion cross section tables were created for the three-dimensional reactor simulator DYNSUB employing the Monte Carlo neutron transport code Serpent 2. In a second step, DYNSUB stationary simulations were compared to Monte Carlo reference three-dimensional full scale solutions obtained with Serpent 2 (cold startup conditions) and Serpent 2/SUBCHANFLOW (operating power conditions) with a good agreement being observed. The latter tool is an internal coupling of Serpent 2 and the sub-channel thermal-hydraulics code SUBCHANFLOW. Finally, DYNSUB was utilized to study the eight selected transient experiments. Results were found to match measurements well. As the selected experiments cover much of the possible transient (delayed super-critical, prompt super-critical and super-prompt critical excursion) and initial conditions (cold and hot as well as zero, little and full power reactor states) one expects in commercial PWRs, the obtained results give confidence that the Serpent 2-DYNSUB tool chain is

  9. Mocvd Growth of Group-III Nitrides on Silicon Carbide: From Thin Films to Atomically Thin Layers

    Science.gov (United States)

    Al Balushi, Zakaria Y.

    of N-polar InGaN by MOCVD is challenging. These challenges arise from the lack of available native substrates suitable for N-polar film growth. As a result, InGaN layers are conventionally grown in the III-polar direction (i.e. III-polar InGaN) and typically grow under considerable amounts of stress on III-polar GaN base layers. While the structure-property relations of thin III-polar InGaN layers have been widely studied in quantum well structures, insight into the growth of thick films and N-polar InGaN layers have been limited. Therefore, this dissertation research compared the growth of both thick III-polar and N-polar InGaN films grown on optimized GaN base layers. III-polar InGaN films were rough and exhibited a high density of V-pits, while the growth of thick N-polar InGaN films showed improved structural quality and low surface roughness. The results of this dissertation work thereby provide an alternative route to the fabrication of thick InGaN films for potential use in solar cells as well as strain reducing schemes for deep-green and red light emitters. Moreover, this dissertation investigated stress relaxation in thick N-polar films using in situ reflectivity and curvature measurements. The results showed that stress relaxation in N-polar InGaN significantly differed from III-polar InGaN due to the absence of V-pits and it was hypothesized that plastic relaxation in N-polar InGaN could occur by dislocation glide, which typically is kinetically limited at such low growth temperatures required for InGaN. The second part of this dissertation research work focused on buffer free growth of GaN directly on SiC and on epitaxial graphene produced on SiC for potential vertical devices. The studies presented in this dissertation work on the growth of GaN directly on SiC compared the stress evolution of GaN films grown with and without an AlN buffer layer. Films grown directly on SiC showed reduced threading dislocation densities and improved surface roughness when

  10. {CoIII2DyIII2} single molecule magnet with two resolved thermal activated magnetization relaxation pathways at zero field.

    Science.gov (United States)

    Funes, Alejandro V; Carrella, Luca; Rentschler, Eva; Alborés, Pablo

    2014-02-14

    The new complex [Co(III)2Dy(III)2(OMe)2(teaH)2(Piv)6] in the {Co(III)2Dy(III)2} family, shows two well resolved thermal activated magnetization relaxation pathways under AC experiments in zero DC field. Fitted crystal field parameters suggest that the origin of these two pathways relies on two different excited mJ sub-levels.

  11. Outcome of tyrosinaemia type III.

    Science.gov (United States)

    Ellaway, C J; Holme, E; Standing, S; Preece, M A; Green, A; Ploechl, E; Ugarte, M; Trefz, F K; Leonard, J V

    2001-12-01

    Tyrosinaemia type III is a rare disorder caused by a deficiency of 4-hydroxyphenylpyruvate dioxygenase, the second enzyme in the catabolic pathway of tyrosine. The majority of the nine previously reported patients have presented with neurological symptoms after the neonatal period, while others detected by neonatal screening have been asymptomatic. All have had normal liver and renal function and none has skin or eye abnormalities. A further four patients with tyrosinaemia type III are described. It is not clear whether a strict low tyrosine diet alters the natural history of tyrosinaemia type III, although there remains a suspicion that treatment may be important, at least in infancy.

  12. Study on competitive adsorption mechanism among oxyacid-type heavy metals in co-existing system: Removal of aqueous As(V), Cr(III) and As(III) using magnetic iron oxide nanoparticles (MIONPs) as adsorbents

    Science.gov (United States)

    Lin, Sen; Lian, Cheng; Xu, Meng; Zhang, Wei; Liu, Lili; Lin, Kuangfei

    2017-11-01

    The adsorption and co-adsorption of As(V), Cr(VI) and As(III) onto the magnetic iron oxide nanoparticles (MIONPs) surface were investigated comprehensively to clarify the competitive processes. The results reflected that the MIONPs had remarkable preferential adsorption to As(V) compared with Cr(VI) and As(III). And it was determined, relying on the analysis of heavy metals variations on the MIONPs surface at different co-adsorption stages using FTIR and XPS, that the inner-sphere complexation made vital contribution to the preferential adsorption for As(V), corresponding with the replacement experiments where As(V) could grab extensively active sites on the MIONPs pre-occupied by As(III) or Cr(V) uniaxially. The desorption processes displayed that the strongest affinity between the MIONPs and As(V) where As(III) and Cr(VI) were more inclined to wash out. It is wish to provide a helpful direction with this study for the wastewater treatment involving multiple oxyacid-type heavy metals using MIONPs as adsorbents.

  13. Sources of type III solar microwave bursts

    Directory of Open Access Journals (Sweden)

    Zhdanov D.A.

    2016-06-01

    Full Text Available Microwave fine structures allow us to study plasma evolution in an energy release region. The Siberian Solar Radio Telescope (SSRT is a unique instrument designed to examine fine structures at 5.7 GHz. A complex analysis of data from RATAN-600, 4–8 GHz spectropolarimeter, and SSRT, simultaneously with EUV data, made it possible to localize sources of III type microwave bursts in August 10, 2011 event within the entire frequency band of burst occurrence, as well as to determine the most probable region of primary energy release. To localize sources of III type bursts from RATAN-600 data, an original method for data processing has been worked out. At 5.7 GHz, the source of bursts was determined along two coordinates, whereas at 4.5, 4.7, 4.9, 5.1, 5.3, 5.5, and 6.0 GHz, their locations were identified along one coordinate. The size of the burst source at 5.1 GHz was found to be maximum as compared to those at other frequencies.

  14. Coastal pollution emergency plan. Part I

    Energy Technology Data Exchange (ETDEWEB)

    Semanov, G.; Volkov, V.; Somkin, V.; Iljushenko-Krylov, D.

    1997-12-31

    A higher degree of ecological safety in ship traffic depends on onboard measures as well as reception facilities on shore, treatment of ship generated wastes and preparedness for combating emergency oil spills. The problem is particularly acute in the North Sea Route (NSR) due to high vulnerability of the Arctic ecosystems, low rates of natural degradation of oil, absence of forward coastal infrastructure, low efficiency of oil combating means in ice conditions and severe climatic conditions. Oil spills in the NSR are likely to occur as the offshore production and transportation of oil increase. Therefore a regional Oil Spill Contingency Plan (OSCP) is being constructed and developed on 3 levels: 1) Development of concept, definition of response organisations and their technical ability (Part I). 2) Collection and analysis of information, development of scenarios of probable oil spills, clearing of the funding mechanism and basis for additional outside co-operation from other Russian regions and circumpolar countries (part II). 3) Development of NSR OSCP (part III). The present report (part I) provides the plan concept, rescue organisations and data on types and amounts of the oil spill combating technical means and of the floating facilities available in the NSR or it`s vicinity. The concept takes into account subdivision of the Route, interaction and links between responsible organisations, realities of the Russian Arctic such as transport, communications, energy, labour resources etc. and requirements of the IMO and of the International Convention OPRC 90. According to Russian legislation implementation of combating operations at sea is the responsibility of the Maritime Pollution Control and Salvage Administration that consists of a Central Administration and basin emergency divisions situated in Murmansk and Nahodka. The body is responsible for carrying out cleaning operations at sea from installations and may be assisted by resources and means of the co

  15. Adsorption behavior of Am(III) on granite

    International Nuclear Information System (INIS)

    Zhang Yingjie; Feng Xiaogui; Liang Junfu; Chen Jing; Su Rui; Wang Ju; Liu Chunli

    2009-01-01

    The adsorption behavior of Am(III) on granite (sampled from drilling well BS01 at Beishan (BS) area--a potential candidate site for China's high-level radioactive waste repository, the granite sample's depth about 300 m) was studied in BS03 well groundwater by a batch technique at (25±1) degree C. The influences of pH, sulphate ion, total carbonate ion, humic acid, and concentration of the Am(III) on the adsorption behavior were also studied, and the possible adsorption mechanism was discussed. Experimental results show that the adsorption distribution rate of Am(III) on granite increases with increasing pH of aqueous phase. The chemical composition of the groundwater is the main factor which influences the species of Am(III) and adsorption behavior. The adsorption mechanism of Am(III) on granite is surface complexation. The adsorption isotherm of Am(III) on granite can be described by Freundlich's equation. (authors)

  16. Optimization of magnetic field system for glass spherical tokamak GLAST-III

    International Nuclear Information System (INIS)

    Ahmad, Zahoor; Ahmad, S; Naveed, M A; Deeba, F; Javeed, M Aqib; Batool, S; Hussain, S; Vorobyov, G M

    2017-01-01

    GLAST-III (Glass Spherical Tokamak) is a spherical tokamak with aspect ratio A = 2. The mapping of its magnetic system is performed to optimize the GLAST-III tokamak for plasma initiation using a Hall probe. Magnetic field from toroidal coils shows 1/ R dependence which is typical with spherical tokamaks. Toroidal field (TF) coils can produce 875 Gauss field, an essential requirement for electron cyclotron resonance assisted discharge. The central solenoid (CS) of GLAST-III is an air core solenoid and requires compensation coils to reduce unnecessary magnetic flux inside the vessel region. The vertical component of magnetic field from the CS in the vacuum vessel region is reduced to 1.15 Gauss kA −1 with the help of a differential loop. The CS of GLAST can produce flux change up to 68 mVs. Theoretical and experimental results are compared for the current waveform of TF coils using a combination of fast and slow capacitor banks. Also the magnetic field produced by poloidal field (PF) coils is compared with theoretically predicted values. It is found that calculated results are in good agreement with experimental measurement. Consequently magnetic field measurements are validated. A tokamak discharge with 2 kA plasma current and pulse length 1 ms is successfully produced using different sets of coils. (paper)

  17. Comparative assessment of characteristic part-load performances of screw compressors and turbo-compressors; Vergleich der charakteristischen Teillastwirkungsgrade von Schrauben- und Turboverdichtern

    Energy Technology Data Exchange (ETDEWEB)

    Brasz, J.J.; Hartmann, K. [Carrier Corp., Syracuse, NY (United States)]|[Carrier Corp., Muenchen (Germany)

    2006-07-01

    The relative part-load performance of screw compressors and radial compressors is compared. Compressor part load is represented by a 2D characteristic field with the pressure on the vertical axis as a function of mass flow on the horizontal axis, with efficiencies given for any possible combination of pressure and mass flow. While this manner of representation is common for radial compressors, it is new for screw compressors. In the comparison of compression efficiencies, the focus is on vapour compression. For a valid comparative assessment of total compression, also the mechanical and/or electric loss through bearings, transmission, drive and (in case of variable-speed drives) frequency converters must be taken into account. (orig.)

  18. Determination of stability constants of iron(III and chromium(III-nitrilotriacetate-methyl cysteine mixed complexes by electrophoretic technique

    Directory of Open Access Journals (Sweden)

    Brij Bhushan Tewari

    2004-06-01

    Full Text Available The stability constants of Fe(III and Cr(III with methyl cysteine and nitrilotriacetate (NTA were determined by paper electrophoretic technique. Beside binary ternary complexes have also been studied, in which nitrilotriacetate and methyl cysteine acts as primary and secondary ligand, respectively. The stability constants of mixed ligand complexes metal (M-nitrilotriacetate-methyl cysteine have been found to be 5.72 plus or minus 0.09 and 5.54 plus or minus 0.11 (log K values for Fe(III and Cr(III complexes, respectively, at 35 oC and ionic strength 0.1 M.

  19. Structural characterization of the Actinides (III) and (IV) - DOTA complexes

    International Nuclear Information System (INIS)

    Audras, Matthieu

    2014-01-01

    The polyamino-carboxylate anions have been identified as compounds of interest in the operations of actinide separation, in actinide migration in the environment and in human radio-toxicology. The structural characterization of complexes formed between actinides and polyamino-carboxylates ligands is essential for a better understanding of actinide-ligands interactions. Among the polyamino-carboxylate anions, the DOTA ligand (1,4,7,10-tetraaza-cyclododecane tetraacetic acid) is described as a very strong complexing agent of the lanthanides(III), but has been little studied with actinides. The objective of this thesis is to describe the complexes formed between the actinides (III) and (IV) and the DOTA ligand, and compare them with the lanthanide complexes. For this, an approach has been introduced to characterize the complexes by complementary analytical techniques (spectrophotometry, electro-spray ionization mass spectrometry, NMR, EXAFS, electrochemistry), but also by calculations of theoretical chemistry to help the interpretation of the experimental data. The formation of a 1:1 complex is observed with the actinides(III) (plutonium and americium) as for lanthanides(III): rapid formation of intermediate species which evolves slowly towards the formation of a limit complex. Within this complex, the cation is located inside the cavity formed by the ligand. Four nitrogen atoms and four oxygen atoms from the carboxylate functions are involved in the coordination sphere of the cation. However, differences were observed in the bond lengths formed between the cation and the nitrogen atoms (the bonds are somewhat shorter in the case of actinide complexes) as well as the complexation kinetics, which is slightly faster for the actinides(III) than for lanthanide(III) ions of equivalent radius. The same behavior was observed in solution upon complexation of actinides(IV) (uranium, plutonium and neptunium): slow formation of a 1:1 complex (actinide(IV):ligand) in wherein the

  20. Sb(III)-Imprinted Organic-Inorganic Hybrid Sorbent Prepared by Hydrothermal-Assisted Surface Imprinting Technique for Selective Adsorption of Sb(III)

    Science.gov (United States)

    Zhang, Dan; Zhao, Yue; Xu, Hong-Bo

    2018-03-01

    Sb(III)-imprinted organic-inorganic hybrid sorbent was prepared by hydrothermal-assisted surface imprinting technique and was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy coupled to an energy dispersive spectrometer and N2 adsorption/desorption isotherms. Hydrothermal-assisted process can improve the selectivity of the Sb(III)-imprinted hybrid sorbent for Sb(III) due to stable control of temperature and pressure. The Sb(III)-imprinted hybrid sorbent IIS indicated higher selectivity for Sb(III), had high static adsorption capacity of 37.3 mg g-1 for Sb(III), displayed stable adsorption capacity in pH range from 4 to 8, reached an rapid adsorption equilibrium within 30 min. According to the correlation coefficient ( r 2 > 0.99), the experimental data fitted better the pseudo-second-order kinetic model and Langmuir equilibrium isotherm.