WorldWideScience

Sample records for paraffin moderator surrounding

  1. Spatial distribution of neutrons in paraffin moderator surrounding a lead target irradiated with protons at intermediate energies

    International Nuclear Information System (INIS)

    Adam, J.; Barabanov, M.Yu.; Bradnova, V.

    2002-01-01

    The distribution of neutrons emitted during the irradiation with 0.65, 1.0 and 1.5 GeV protons from a lead target (O / = 8 cm, l = 20 cm) and moderated by a surrounding paraffin moderator of 6 cm thick was studied with a radiochemical sensor along the beam axis on top of the moderator. Small 139 La-sensors of approximately 1 g were used to measure essentially the thermal neutron fluence at different depths near the surface: i.e., on top of the moderator, in 10 mm deep holes and in 20 mm deep holes. The reaction 139 La(n, γ) 140 La (τ 1/2 = 40.27 h) was studied using standard procedures of gamma spectroscopy and data analysis. The neutron induced activity of 140 La increases strongly with the depth of the hole inside the moderator, its activity distribution along the beam direction on top of the moderator has its maximum about 10 cm downstream the entrance of the protons into the lead and the induced activity increases about linearity with the proton energy. Some comparisons of the experimental results with model estimations based on the LAHET code are also presented. The experiments were carried out using the Nuclotron accelerator of the Laboratory of High Energies (JINR)

  2. Spatial distribution of neutrons in paraffin moderator surrounding a lead target irradiated with protons at intermediate energies

    CERN Document Server

    Adam, J; Bradnova, V

    2002-01-01

    The distribution of neutrons emitted during the irradiation with 0.65, 1.0 and 1.5 GeV protons from a lead target (O / = 8 cm, l = 20 cm) and moderated by a surrounding paraffin moderator of 6 cm thick was studied with a radiochemical sensor along the beam axis on top of the moderator. Small sup 1 sup 3 sup 9 La-sensors of approximately 1 g were used to measure essentially the thermal neutron fluence at different depths near the surface: i.e., on top of the moderator, in 10 mm deep holes and in 20 mm deep holes. The reaction sup 1 sup 3 sup 9 La(n, gamma) sup 1 sup 4 sup 0 La (tau sub 1 sub / sub 2 = 40.27 h) was studied using standard procedures of gamma spectroscopy and data analysis. The neutron induced activity of sup 1 sup 4 sup 0 La increases strongly with the depth of the hole inside the moderator, its activity distribution along the beam direction on top of the moderator has its maximum about 10 cm downstream the entrance of the protons into the lead and the induced activity increases about linearity ...

  3. Modelling of an experiment INSS and paraffin moderator at JINR

    International Nuclear Information System (INIS)

    Goyal, Uttam; Kumawat, Harphool; Kumar, V.; Barashenkov, V.S.

    2002-01-01

    Intense neutron spallation source (INSS) described elsewhere is studied with paraffin moderator using the Dubna cascade code. For the present study paraffin is assumed having configuration corresponding to C 22 H 46 with density = 0.87 g/cm 3 6 cm thickness of paraffin is coated around the Pb-spallation target of size ΦxL = 8x20 cm 2 and proton beam with E lab = 1 GeV is allowed to collide at the center of the left face

  4. Paraffin wax

    Energy Technology Data Exchange (ETDEWEB)

    Elborne, W

    1917-06-16

    Powdered, granulated, or finely divided paraffin is obtained by subjecting paraffin to a grinding, crushing, or disintegrating operation in the presence of an alcohol such as ethyl alcohol, methyl alcohol (wood spirit), or methylated spirit. The alcohol is afterwards removed by a current of air and is recovered. The product can be used in conjunction with a heating-agent for producing smoke or vapor for use in warfare.

  5. Detection of pulsed fast neutrons by a proportional counter boron-convered and enveloped in paraffin moderators

    International Nuclear Information System (INIS)

    Goncalez, O.L.; Yanagihara, L.S.; Veissid, V.L.C.P.; Herdade, S.B.

    1983-01-01

    The response to pulsed fast neutrons by a parafin moderated boron-lined proportional counter is investigated theoretically and experimentally. The neutrons pulses are generated by 60 MeV electrons from a linear accelerator. The calculation of the counting loss based on the detector dead time and on the exponential decresse of the thermal neutron population in the moderator is presented in detail. An analytical relation between the true counting rate and the reduced one, indicated by the detector, is found. In this formula three parameters appear: the decay constant of the thermal neutron population, the detector dead time and the pulse frequency of the neutron source. The decay constant is calculated by diffusion theory. The experimental results for six values of moderator thickness (between 2.5 to 12.5 cm) agree with our theoretical calculation within 20 per cent. (Author) [pt

  6. Development of the neutron reference calibration field using a {sup 252}Cf standard source surrounded with PMMA moderators

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, T.; Kanai, K.; Tsujimura, N. [Japan Nuclear Cycle Development Institute, Ibaraki-ken (Japan)

    2002-07-01

    The authors developed the neutron reference calibration fields using a {sup 252} Cf standard source surrounded with PMMA moderators at the Japan Nuclear Cycle Development (JNC), Tokai Works. The moderators are co-axial, hollow cylinders made of lead-contained PMMA with a thickness of 13.5, 35.0, 59.5 and 77.0mm, and the {sup 252} Cf source is guided to the geometric center of moderators by the pneumatic system. These fields can provide the moderated neutron spectra very similar to those encountered around the globe-boxes of the fabrication process of MOX (PuO{sub 2}-UO{sub 2} mixed oxide) fuel. The neutron energy spectrum at the reference calibration point was evaluated from the calculations by MCNP4B and the measurements by the INS-type Bonner multi-sphere spectrometer and the hydrogen-filled proportional counters. The calculated neutron spectra were in good agreements with the measured ones. These fields were characterized in terms of the neutron fluence rate, spectral composition and ambient dose equivalent rate, and have served for the response-characterization of various neutron survey instruments.

  7. Development of the neutron reference calibration field using a 252Cf standard source surrounded with PMMA moderators

    International Nuclear Information System (INIS)

    Yoshida, T.; Kanai, K.; Tsujimura, N.

    2002-01-01

    The authors developed the neutron reference calibration fields using a 252 Cf standard source surrounded with PMMA moderators at the Japan Nuclear Cycle Development (JNC), Tokai Works. The moderators are co-axial, hollow cylinders made of lead-contained PMMA with a thickness of 13.5, 35.0, 59.5 and 77.0mm, and the 252 Cf source is guided to the geometric center of moderators by the pneumatic system. These fields can provide the moderated neutron spectra very similar to those encountered around the globe-boxes of the fabrication process of MOX (PuO 2 -UO 2 mixed oxide) fuel. The neutron energy spectrum at the reference calibration point was evaluated from the calculations by MCNP4B and the measurements by the INS-type Bonner multi-sphere spectrometer and the hydrogen-filled proportional counters. The calculated neutron spectra were in good agreements with the measured ones. These fields were characterized in terms of the neutron fluence rate, spectral composition and ambient dose equivalent rate, and have served for the response-characterization of various neutron survey instruments

  8. A Catalogue of Source Parameters of Moderate and Strong Earthquakes for Turkey and its Surrounding Area (1938-2015)

    Science.gov (United States)

    Kalafat, D.; Toksoz, M. N.

    2015-12-01

    Turkey and Surrounding area, especially North Anatolian Fault Zone (NAFZ), East Anatolian Fault Zone (EAFZ), Western Turkey, cost of the Aegean Sea and Mediterranean Sea regions are seismically very active and undergoing rapid deformation. Earthquakes with M >6.0 do occur every couple of years regularly in this region, Moderate-magnitude seismicity (4.04.0 which were calculated of the fault-source parameters for Turkey and its surrounding area between 1938-2015. The fault source parameters of total over the 1200 earthquakes were calculated. The fault-source parameters of about 56.0 % of the all events were calculated with this study and 44.0 % of the rest were obtained from the other sources. The parameters of the old and incomplete events also were calculated in order to prepare the homogeneous and extended fault- source parameters set in the study. ACKNOWLEDGMENTS This study was supported by the Department of Science Fellowship and Grant programs of TUBITAK (The Scientific and Technological Research Council of Turkey).

  9. Preparing paraffin wax, etc

    Energy Technology Data Exchange (ETDEWEB)

    1935-12-27

    A process is described for preparing paraffin wax by separation from substances containing bitumen, consisting of treating the raw material at an elevated temperature under such moderate conditions and by means of such organic solvents that the bitumen present in the raw material or formed in the process dissolves as well as the asphaltic and phenolic substances and the humic acids which may be said to be neither extracts nor decomposed materials, and then submitting the products and extracts to a treatment with hydrogen gas, which is effected below 300/sup 0/C, and passing the material over fixed hydrogenation catalysts above 300/sup 0/C by means of hydrogenation catalysts finely dispersed in carbonaceous materials all avoiding decomposition with the formation of volatile products.

  10. CARR-CNS with crescent-shape moderator cell and sub-cooling helium jacket surrounding cell

    International Nuclear Information System (INIS)

    Yu, Qingfeng; Feng, Quanke; Kawai, Takeshi; Shen, Feng; Yuan, Luzheng

    2005-01-01

    The new type of the moderator cell was developed for the Cold Neutron Source (CNS) of the China Advanced Research Reactor (CARR) which is now constructing at the China Institute of Atomic Energy in Beijing. A crescent-shape moderator cell covered by the sub-cooling helium jacket is adopted. A crescent-shape would help to increase the volume of the moderator cell for corresponding it to the 4 cold neutron guide tubes, even if liquid hydrogen not liquid deuterium were used as a cold moderator. The sub-cooling helium jacket covering the moderator cell removes the nuclear heating of the outer shell wall of the cell. It contributes to reduce the void fraction of liquid hydrogen in the inner shell. Such a type of a moderator cell is suitable for the CNS with higher nuclear heating. The cold helium gas flows down firstly into the sub-cooling helium jacket and then flows up to the condenser. Therefore, the theory of the self-regulation for the thermo-siphon type of the CNS is also applicable

  11. Paraffin ingestion - the problem

    African Journals Online (AJOL)

    The incidence of paraffin ingestion is higher in the summer months. This is because ... where the average cost per patient was R348 per day. The total cost to ... petroleum companies and/or entrepreneurs and distributed ... paraffin, coal and gas. As South Africa ... and more people become involved, making control difficult.

  12. PARAFFIN SEPARATION VACUUM DISTILLATION

    Directory of Open Access Journals (Sweden)

    Zaid A. Abdulrahman

    2013-05-01

    Full Text Available Simulated column performance curves were constructed for existing paraffin separation vacuum distillation column in LAB plant (Arab Detergent Company/Baiji-Iraq. The variables considered in this study are the thermodynamic model option, top vacuum pressure, top and bottom temperatures, feed temperature, feed composition & reflux ratio. Also simulated columns profiles for the temperature, vapor & liquid flow rates composition were constructed. Four different thermodynamic model options (SRK, TSRK, PR, and ESSO were used, affecting the results within 1-25% variation for the most cases.The simulated results show that about 2% to 8 % of paraffin (C10, C11, C12, & C13 present at the bottom stream which may cause a problem in the LAB plant. The major variations were noticed for the top temperature & the  paraffin weight fractions at bottom section with top vacuum pressure. The bottom temperature above 240 oC is not recommended because the total bottom flow rate decreases sharply, where as  the weight fraction of paraffins decrease slightly. The study gives evidence about a successful simulation with CHEMCAD

  13. Plastics control paraffin buildup

    Energy Technology Data Exchange (ETDEWEB)

    1965-06-01

    Paraffin buildup in producing oil wells has been virtually eliminated by the use of plastic-coated sucker rods. The payout of the plasticing process is generally reached in less than a year, and the paraffin buildup may be inhibited for 10 yr or longer. Most of the plants applying plastic coatings to sucker rods are now fully automated, though a few still offer the hand-sprayed coating that some operators prefer. The several steps involved are described. The ideal plastic for the job is resistant to chemicals at high and low temperatures, flexible, has good adhesion, abrasion resistance, impact resistance, and a smooth glossy finish. The phenol aldehyde and epoxy resins presently offered by the industry fulfill these specifications very well; the multicoating and multibaking techniques improve their performance. Due to wide variations in the severity of the paraffin problem from one oil field to another, there is no general rule to estimate the possible savings from using plastic-coated sucker rods. The process, however, does appear to do a remarkable job in controlling paraffin buildup wherever it is a problem in producing oil by pump.

  14. Preventing Paraffin-Related Injury

    Directory of Open Access Journals (Sweden)

    Dehran Swart

    2009-07-01

    Full Text Available Paraffin (called kerosene in North America and other parts of the world is the most commonly used fuel in ‎non-electrified dwellings worldwide. It is especially popular in Africa and South Asia. Although paraffin ‎offers many advantages – especially its comparatively low cost to produce – it poses two major risks of ‎injury. First, paraffin poisoning is common, either through ingestion or through inhalation of smoke and ‎fumes. Second, paraffin is highly flammable, and poses fire risk through multiple causes. This commentary ‎discusses strategies to prevent paraffin-related injury. Prevention of paraffin-related injury must be through ‎multiple strategies, and should include policy-oriented change, changes to the safety of home environments, ‎and behavioral changes targeting how individuals store and use paraffin and paraffin appliances. We review ‎successful prevention strategies in each of these domains and discuss appropriate research and community ‎initiatives that should be implemented to improve paraffin safety among at-risk populations.‎

  15. Preventing Paraffin-Related Injury

    OpenAIRE

    C. Schwebel, David; Swart, Dehran

    2009-01-01

    Paraffin (called kerosene in North America and other parts of the world) is the most commonly used fuel in ‎non-electrified dwellings worldwide. It is especially popular in Africa and South Asia. Although paraffin ‎offers many advantages – especially its comparatively low cost to produce – it poses two major risks of ‎injury. First, paraffin poisoning is common, either through ingestion or through inhalation of smoke and ‎fumes. Second, paraffin is highly flammable, and poses fire risk t...

  16. Spallation Neutron Spectrum on a Massive Lead/Paraffin Target Irradiated with 1 GeV Protons

    CERN Document Server

    Adam, J; Barashenkov, V S; Brandt, R; Golovatiouk, V M; Kalinnikov, V G; Katovsky, K; Krivopustov, M I; Kumar, V; Kumawat, H; Odoj, R; Pronskikh, V S; Solnyshkin, A A; Stegailov, V I; Tsoupko-Sitnikov, V M; Westmeier, W

    2004-01-01

    The spectra of gamma-ray emitted by decaying residual nuclei, produced by spallation neutrons with (n, xn), (n,xnyp), (n,p), (n,gamma) reactions in activation threshold detectors - namely, ^{209}Bi, ^{197}Au, ^{59}Co, ^{115}In, ^{232}Th, were measured in the Laboratory of Nuclear Problems (LNP), JINR, Dubna, Russia. Spallation neutrons were generated by bombarding a 20 cm long cylindrical lead target, 8 cm in diameter, surrounded by a 6 cm thick layer of paraffin moderator, with a 1 GeV proton beam from the Nuclotron accelerator. Reaction rates and spallation neutron spectrum were measured and compared with CASCADE code calculations.

  17. Influence of Liquid Paraffin, White Soft Paraffin and Initial Hydration ...

    African Journals Online (AJOL)

    hydrated white soft paraffin on the viscosity of a cream formulated with a corticosteroid. Methods: The formulations were prepared via homogenization with variable velocity in the range 3300 - 4000 rpm. Individual series of preparations contained the ...

  18. Smart Surroundings

    NARCIS (Netherlands)

    Havinga, Paul J.M.; Jansen, P.G.; Lijding, M.E.M.; Scholten, Johan

    2004-01-01

    Ambient systems are networked embedded systems integrated with everyday environments and supporting people in their activities. These systems will create a Smart Surrounding for people to facilitate and enrich daily life and increase productivity at work. Such systems will be quite different from

  19. Nitrous Paraffin Hybrid, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The Nitrous Oxide Paraffin Hybrid engine (N2OP) is a proposed technology designed to provide small launch vehicles with high specific impulse, indefinitely storable...

  20. TULSA UNIVERSITY PARAFFIN DEPOSITION PROJECTS

    Energy Technology Data Exchange (ETDEWEB)

    Cem Sarica; Michael Volk

    2004-06-01

    As oil and gas production moves to deeper and colder water, subsea multiphase production systems become critical for economic feasibility. It will also become increasingly imperative to adequately identify the conditions for paraffin precipitation and predict paraffin deposition rates to optimize the design and operation of these multi-phase production systems. Although several oil companies have paraffin deposition predictive capabilities for single-phase oil flow, these predictive capabilities are not suitable for the multiphase flow conditions encountered in most flowlines and wellbores. For deepwater applications in the Gulf of Mexico, it is likely that multiphase production streams consisting of crude oil, produced water and gas will be transported in a single multiphase pipeline to minimize capital cost and complexity at the mudline. Existing single-phase (crude oil) paraffin deposition predictive tools are clearly inadequate to accurately design these pipelines, because they do not account for the second and third phases, namely, produced water and gas. The objective of this program is to utilize the current test facilities at The University of Tulsa, as well as member company expertise, to accomplish the following: enhance our understanding of paraffin deposition in single and two-phase (gas-oil) flows; conduct focused experiments to better understand various aspects of deposition physics; and, utilize knowledge gained from experimental modeling studies to enhance the computer programs developed in the previous JIP for predicting paraffin deposition in single and two-phase flow environments. These refined computer models will then be tested against field data from member company pipelines.

  1. Preparation and thermal properties of form stable paraffin phase change material encapsulation

    International Nuclear Information System (INIS)

    Liu Xing; Liu Hongyan; Wang Shujun; Zhang Lu; Cheng Hua

    2006-01-01

    Paraffin waxes are cheap and have moderate thermal energy storage density but low thermal conductivity and, hence, require large surface area to be used in energy storage. Form stable paraffin phase change materials (PCM) in which paraffin serves as a latent heat storage material and polyolefins act as a supporting material, because of paraffin leakage, are required to be improved. The form stable paraffin PCM in the present paper was encapsulated in an inorganic silica gel polymer successfully by in situ polymerization. The differential scanning calorimeter (DSC) was used to measure its thermal properties. At the same time, the Washburn equation, which measures the wetting properties of powder materials, was used to test the hydrophilic-lipophilic properties of the PCMs. The result indicated that the enthalpy of the microencapsulated PCMs was reduced little, while their hydrophilic properties were enhanced largely

  2. 21 CFR 890.5110 - Paraffin bath.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Paraffin bath. 890.5110 Section 890.5110 Food and... PHYSICAL MEDICINE DEVICES Physical Medicine Therapeutic Devices § 890.5110 Paraffin bath. (a) Identification. A paraffin bath is a device intended for medical purposes that consists of a tub to be filled...

  3. Surfactants from petroleum paraffin wax

    Energy Technology Data Exchange (ETDEWEB)

    Kassem, T.M.; Hussein, M.H.; El Sayed, A.S.

    Paraffin wax from Egyptian petroleum was purified and then oxidized to fatty acids which were esterified to form their methyl esters, fractionated and then hydrolysed. The obtained fatty acids were converted into the corresponding primary amines which were converted with ethylene oxide to form nonionic surfactants. The prepared primary amines were also converted into tertiary amines and then converted into cationic surfactants through condensation with benzyl chloride or 1-chloromethylnaphthalene. Also, amine oxide surfactants were prepared by oxidation of the tertiary amines with hydrogen peroxide. The surface active properties of all the prepared surfactants were determined, and the effect of their chemical structure on the surfactant properties are discussed in this paper.

  4. Nitrous Oxide/Paraffin Hybrid Rocket Engines

    Science.gov (United States)

    Zubrin, Robert; Snyder, Gary

    2010-01-01

    Nitrous oxide/paraffin (N2OP) hybrid rocket engines have been invented as alternatives to other rocket engines especially those that burn granular, rubbery solid fuels consisting largely of hydroxyl- terminated polybutadiene (HTPB). Originally intended for use in launching spacecraft, these engines would also be suitable for terrestrial use in rocket-assisted takeoff of small airplanes. The main novel features of these engines are (1) the use of reinforced paraffin as the fuel and (2) the use of nitrous oxide as the oxidizer. Hybrid (solid-fuel/fluid-oxidizer) rocket engines offer advantages of safety and simplicity over fluid-bipropellant (fluid-fuel/fluid-oxidizer) rocket en - gines, but the thrusts of HTPB-based hybrid rocket engines are limited by the low regression rates of the fuel grains. Paraffin used as a solid fuel has a regression rate about 4 times that of HTPB, but pure paraffin fuel grains soften when heated; hence, paraffin fuel grains can, potentially, slump during firing. In a hybrid engine of the present type, the paraffin is molded into a 3-volume-percent graphite sponge or similar carbon matrix, which supports the paraffin against slumping during firing. In addition, because the carbon matrix material burns along with the paraffin, engine performance is not appreciably degraded by use of the matrix.

  5. 7 CFR 58.427 - Paraffin tanks.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Paraffin tanks. 58.427 Section 58.427 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....427 Paraffin tanks. The metal tank should be adequate in size, have wood rather than metal racks to...

  6. A randomized double-blind, placebo-controlled efficacy and safety study of ALO-02 (extended-release oxycodone surrounding sequestered naltrexone) for moderate-to-severe chronic low back pain treatment.

    Science.gov (United States)

    Rauck, Richard L; Hale, Martin E; Bass, Almasa; Bramson, Candace; Pixton, Glenn; Wilson, Jacquelyn G; Setnik, Beatrice; Meisner, Paul; Sommerville, Kenneth W; Malhotra, Bimal K; Wolfram, Gernot

    2015-09-01

    The objective of this multicenter, double-blind, placebo-controlled, randomized withdrawal study was to evaluate the efficacy and safety of ALO-02, an abuse-deterrent formulation containing pellets of extended-release oxycodone hydrochloride (HCl) surrounding sequestered naltrexone HCl, compared with placebo in the treatment of moderate-to-severe chronic low back pain. An open-label titration period in which all patients received ALO-02 was followed by a double-blind treatment period where patients meeting treatment response criteria were randomized to either a fixed dose of ALO-02 or placebo. Daily average low back pain was assessed using an 11-point numeric rating scale (NRS)-Pain. Of the 663 patients screened, 410 received ALO-02 during the open-label conversion and titration period and 281 patients were randomized to the double-blind treatment period (n = 134, placebo; n = 147, ALO-02). Change in the mean NRS-Pain score from randomization baseline to the final 2 weeks of the treatment period was significantly different favoring ALO-02 compared with placebo (P = 0.0114). Forty-four percent of patients treated with placebo and 57.5% of patients treated with ALO-02 reported ≥30% improvement in weekly average NRS-Pain scores from screening to the final 2 weeks of the treatment period (P = 0.0248). In the double-blind treatment period, 56.8% of patients in the ALO-02 group and 56.0% of patients in the placebo group experienced a treatment-emergent adverse event (TEAE). The most common treatment-related TEAEs for ALO-02 during the treatment period were nausea, vomiting, and constipation, consistent with opioid therapy. ALO-02 has been demonstrated to provide significant reduction of pain in patients with chronic low back pain and has a safety profile similar to other opioids.

  7. Rubidium dimers in paraffin-coated cells

    International Nuclear Information System (INIS)

    Acosta, V M; Windes, D; Corsini, E; Ledbetter, M P; Karaulanov, T; Budker, D; Jarmola, A; Auzinsh, M; Rangwala, S A; Jackson Kimball, D F

    2010-01-01

    Measurements were made to determine the density of rubidium dimer vapor in paraffin-coated cells. The number density of dimers and atoms in similar paraffin-coated and uncoated cells was measured by optical spectroscopy. Due to the relatively low melting point of paraffin, a limited temperature range of 43-80 0 C was explored, with the lower end corresponding to a dimer density of less than 10 7 cm -3 . With 1 min integration time, a sensitivity to dimer number density of better than 10 6 cm -3 was achieved. No significant difference in dimer density between the cells was observed.

  8. Solubilization of paraffinic deposits for microemulsions

    Energy Technology Data Exchange (ETDEWEB)

    Gomes, Erika A.S.; Soares, Ranieri G.F.; Nascimento, Roseane E.S.; Dantas Neto, Afonso A.; Barros Neto, Eduardo L. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

    2008-07-01

    The oil company has been intensifying its efforts to find more efficient solutions for the problems related to the paraffin in wells and transport lines. When applied in the flow lines, the solvents dissolve the paraffin and they must be used hot, since the temperature increases the solubility of the wax and, consequently, its removal rate. The microemulsions appear as an alternative capable of acting in the solubilization and in the inhibition of the formation of deposits due to its great interfacial area, low superficial tension and high capacity of solubilization. They present some advantages in relation to the methods of use of chemical products due to its flexibility of composition in which they can be used, presenting low toxicity and inflammability, without any loss of its capacity of solubilization. The use of oil-in-water microemulsion aims to solubilized paraffin in the disperse phase, where one can find the apolar part of the molecule of the surfactant and the also apolar chain of paraffin, occurring, therefore the 'encapsulation' of the crystal, prohibiting the growth of the chain due to the affinity of paraffin and oil. In this in case, it is possible to transport the inserted paraffin in direct micelles, reducing the precipitation and optimizing the transport. (author)

  9. Formulation and Testing of Paraffin-Based Solid Fuels Containing Energetic Additives for Hybrid Rockets

    Science.gov (United States)

    Larson, Daniel B.; Boyer, Eric; Wachs,Trevor; Kuo, Kenneth K.; Story, George

    2012-01-01

    with both paraffin and RDX, the mixture will be combined with the melted paraffin. With the melting point of the paraffin far below the decomposition temperature of the RDX, the solvent will be boiled off, leaving the crystallized RDX embedded in the paraffin. At low percentages of RDX additive and with crystallized RDX surrounded by paraffin, the fuel grains will remain inert, maintaining a key benefit of hybrids in the safety of the solid fuel.

  10. Biodegradation of paraffin wax by crude Aspergillus enzyme preparations for potential use in removing paraffin deposits.

    Science.gov (United States)

    Zhang, Junhui; Xue, Quanhong; Gao, Hui; Wang, Ping

    2015-11-01

    Paraffin deposition problems have plagued the oil industry. Whist mechanical and chemical methods are problematic, microbiological method of paraffin removal is considered an alternative. However, studies have mainly investigated the use of bacteria, with little attention to the potential of fungi. The performance of six Aspergillus isolates to degrade paraffin wax was evaluated under laboratory conditions using solid enzyme preparations. The results showed that all the six enzyme preparations efficiently improved the solubility of paraffin wax in n-hexane and degraded n-alkanes in paraffin wax. The degradation process was accompanied by dynamic production of gases (CO2 and H2 ) and organic acids (oxalate and propionate). The shape of wax crystals markedly changed after enzymatic degradation, with a rough surface and a loose structure. This study indicates that extracellular enzymes from Aspergillus spp. can efficiently degrade paraffin wax. These enzyme preparations have the potential for use in oil wells with paraffin deposition problems. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Murine immune response induced by Leishmania major during the implantation of paraffin tablets.

    Science.gov (United States)

    Reis, Maria Letícia Costa; Ferreira, Vanessa Martins; Zhang, Xia; Gonçalves, Ricardo; Vieira, Leda Quércia; Tafuri, Washington Luiz; Mosser, David M; Tafuri, Wagner Luiz

    2010-11-01

    We carried out a model of chronic inflammation using a subcutaneous paraffin tablet in mice experimentally infected with Leishmania major. It was previously reported that the parasite load following paraffin implantation occurred at a peak of 21 days in both BALB/c and C57BL/6 mice. At the present study, we have investigated what cytokines and chemokines are directly related to the parasite load in C57BL/6 mice. All mice were divided in four groups: mice implanted with paraffin tablets; mice experimentally infected with L. major; mice implanted with paraffin tablets and experimentally infected with L. major; and mice submitted only to the surgery were used for the Real-Time Polymerase Chain Reaction (RT-PCR) controls. Fragments of skin tissue and the tissue surrounding the paraffin tablets (inflammatory capsule) were collected for histopathology and RT-PCR studies. By 21 days, a diffuse chronic inflammatory reaction was mainly observed in the deep dermis where macrophages parasitized with Leishmania amastigotes were also found. RT-PCR analysis has shown that BALB/c mice showed strong IL-4 and IL-10 mRNA expression than controls with very little expression of IFN-γ. In contrast, both IFN-γ and IL-10 mRNA was found in higher levels in C57BL/6 animals. Moreover, in C57BL/6 mice the expression of chemokines mRNA of CCL3/MIP-1α was more highly expressed than CCL2/MCP-1. We conclude that the Th1 immune response C57BL/6 did not change to a Th2 response, even though C57BL/6 animals presented higher parasitism than BALB/c mice 21 days after infection and paraffin implantation.

  12. Recrystallization phenomena of solution grown paraffin dendrites

    NARCIS (Netherlands)

    Hollander, F.F.A.; Hollander, F.; Stasse, O.; van Suchtelen, J.; van Enckevort, W.J.P.

    2001-01-01

    Paraffin crystals were grown from decane solutions using a micro-Bridgman set up for in-situ observation of the morphology at the growth front. It is shown that for large imposed velocities, dendrites are obtained. After dendritic growth, aging or recrystallization processes set in rather quickly,

  13. Topical analgesic added to paraffin enhances paraffin bath treatment of individuals with hand osteoarthritis.

    Science.gov (United States)

    Myrer, Joseph William; Johnson, Aaron Wayne; Mitchell, Ulrike H; Measom, Gary J; Fellingham, Gilbert W

    2011-01-01

    To compare treating patients with symptomatic hand osteoarthritis (OA) with paraffin baths only (PO) (100% wax) or paraffin baths 80% wax with 20% topical analgesic (PTA). Subjects met criteria of the American College of Rheumatology for classifying symptomatic hand OA and had a Dreiser's index score >5 points. Current and average pain at rest and with movement was assessed with visual analogue scales. Hand function was assessed by the functional index for hand OA (FIHOA). Both groups had a significant reduction in their 'current' pain 15 min after the first and twelfth treatments compared to pre-treatment but there was no difference between groups (t = 0.10, p > 0.05). The PTA group had greater improvement over the 12 treatment sessions for their pain at rest (t = 2.92, p paraffin produced significantly greater pain relief at rest and during movement than paraffin baths alone after 12 treatments. Additionally, the PTA group experienced greater improved hand function.

  14. A method for producing liquid paraffin

    Energy Technology Data Exchange (ETDEWEB)

    Dorodnova, V.S.; Martynenko, A.G.; Pereverzev, A.N.

    1983-01-01

    In the known method (Sp) for producing liquid paraffins (ZhP) through processing an oil fraction by crystalline carbamide in the presence of a solvent with subsequent removal of the formed complex (Km) of KA with the liquid paraffins from the deparaffinized product, staged washing and decomposition of the complex with isolation of the liquid paraffins, in order to increase the output of liquid paraffin and to improve its quality, beta,beta'-dichlorethyl ether (khloreks) in a mixture with methylethyl ketone (MEK) or methylisobutyl ketone in a ratio of 1 is used as the solvent, the processing by the crystalline carbamide is conducted with the addition of 180 to 260 percent solvent to raw material (Sr) and the washing of the composition is conducted by a solvent in the first stage and by methylethyl ketone or methylisobutyl ketone in the second stage. The crystalline carbamide for the complex formation is taken in a conversion of 60 to 70 percent for the raw material for observing the raw material to solvent ratio of from 1 to 1.8 to 2.6 to 0.6 to 0.6. The temperature in the zone of formation of the complex is maintained at 5 to 35 degrees. The presence of beta,beta'-dichlorethyl ether, which has high selectivity relative to aromatic hydrocarbons (ArU) and to resinous compounds provides for a sharp reduction in the adsorption of the undesired components on the surface of the granules of the complex and the crystalline carbamide and to a reduction in the portion of the alkylaromatic hydrocarbons (UV) extracted into the complex, which leads to a substantial improvement in the quality of the obtained liquid paraffins.

  15. 21 CFR 172.275 - Synthetic paraffin and succinic derivatives.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Synthetic paraffin and succinic derivatives. 172... FOOD FOR HUMAN CONSUMPTION Coatings, Films and Related Substances § 172.275 Synthetic paraffin and succinic derivatives. Synthetic paraffin and succinic derivatives identified in this section may be safely...

  16. Magnetization of Paraffin-Based Magnetic Nanocolloids

    Science.gov (United States)

    Dikanskii, Yu. I.; Ispiryan, A. G.; Kunikin, S. A.; Radionov, A. V.

    2018-01-01

    Using paraffin-based magnetic nanocolloids as an example, the reasons for maxima in the temperature dependence of the magnetic susceptibility of magnetic colloids have been discussed. The behavior of these dependences in a wide temperature interval has been analyzed for colloids in solid and liquid states. It has been concluded that the maximum observed at the melting point of paraffin can be attributed to freezing Brownian degrees of freedom in magnetite coarse particles, the magnetic moment of which is intimately related to the solid matrix. The second main maximum, which arises in the solid state, is explained by the superparamagnetic-magnetically hard transition of most fine particles at lower temperatures. It has been noted that the flatness of this maximum results from the polydispersity of the magnetic nanoparticle ensemble.

  17. Interaction of oil and paraffin with sodium

    Energy Technology Data Exchange (ETDEWEB)

    Kozlov, F A; Zagorulko, Yu I; Kovalev, Yu P; Lamykin, E V; Alekseev, V V; Sergeev, G P [Institute of Physics and Power Engineering, Obninsk (USSR)

    1980-05-01

    This report presents the investigation results on the kinetics of a gaseous oil pyrolysis product composition change in the presence of sodium under static conditions at 350 deg. C, 550 deg. C and 700 deg. C as well as the behaviour of oil and paraffin within the sodium circulating loops. The calculated estimations of the critical oil physical state parameters in sodium flows are given. (author)

  18. Interaction of oil and paraffin with sodium

    International Nuclear Information System (INIS)

    Kozlov, F.A.; Zagorulko, Yu.I.; Kovalev, Yu.P.; Lamykin, E.V.; Alekseev, V.V.; Sergeev, G.P.

    1980-01-01

    This report presents the investigation results on the kinetics of a gaseous oil pyrolysis product composition change in the presence of sodium under static conditions at 350 deg. C, 550 deg. C and 700 deg. C as well as the behaviour of oil and paraffin within the sodium circulating loops. The calculated estimations of the critical oil physical state parameters in sodium flows are given. (author)

  19. Bio-paraffins: alternative products to petroleum paraffins; Bioparafinas: produtos alternativos as parafinas de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Anie Daniela Medeiros [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES). Gerencia de Hidrorrefino e Processos Especiais; Oliveira, Claudia Cristina Cardoso Calvano de; Carvalho, Ivone de Freitas; Silva, Danilo do Carmo Santos; Cruz, Valeria Senra da Silva [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES). Gerencia de Lubrificantes e Produtos Especiais]. E-mails: anie.lima, claudiacristina, ivone, danilosilva, vsenra@petrobras.com.br

    2007-04-15

    Market trends and social and environmental issues encouraged the vegetal wax presence in the world-wide paraffin market. This work presents the most commercialized vegetal waxes, soy and pal, comparing their physicochemical characteristics and their applicability with the paraffins obtained from petroleum. It also presents a characterization of the carnauba wax, produced exclusively in Brazil and a comparison with paraffins from petroleum. The carnauba wax is an alternative product, with good applicability as a substitute for waxes from petroleum or a petroleum/vegetal mixture. The characteristics of palm and soy waxes show the possible application in candles, cosmetics, foods and others industries. Brazil, having a great agricultural potential, represents a source of vegetal wax that could be use to meet the market demands. (author)

  20. Experimental analysis of a paraffin-based cold storage tank

    OpenAIRE

    Barbara Torregrosa-Jaime; López-Navarro, Alejandro; Corberán, José M.; Esteban-Matías, J. C.; Klinkner, L.; Payá-Herrero, Jorge

    2013-01-01

    [EN] The aim of this study is to characterize a paraffin-based cold storage tank. Novel experimental results are presented for this system which combines a significant amount of paraffin (1450 kg) immersed around 18 spiral-shaped coils disposed in counter-current flow. The paraffin has a phase-change temperature in the range 4 8 °C as measured by a 3-layer calorimeter. Different tests have been carried out with a constant mass flow rate and supply temperature. Around 31% of the paraffin has h...

  1. Development of paraffin and paraffin/bitumen composites with additions of B2O3 for thermal neutron shielding applications

    International Nuclear Information System (INIS)

    Toyen, Donruedee; Saenboonruang, Kiadtisak

    2017-01-01

    In this work, paraffin and paraffin/bitumen composites with additions of boron oxide (B 2 O 3 ) were prepared to evaluate the viscosity, flexural, and thermal neutron shielding properties for uses as thermal neutron shielding materials. The results showed that the addition of 3 wt% or 9 wt% bitumen to paraffin increased the overall flexural properties with the content of 9 wt% bitumen having the highest values. The improvement in flexural properties made the composites less brittle, stiffer, and longer-lasting. Furthermore, different contents of B 2 O 3 (0, 7, 14, 21, 28, and 35 wt%) were added to paraffin and paraffin/bitumen composites to investigate the effects of the B 2 O 3 contents. The results indicated that an increase in B 2 O 3 contents improved the shielding properties but slightly reduced the flexural properties. Specifically for 5-mm paraffin and 5-mm paraffin/bitumen samples with 35 wt% of B 2 O 3 , both samples could reduce neutron flux by more than 70%. The overall results suggested that the paraffin and paraffin/bitumen composites with additions of B 2 O 3 showed improved properties for utilization as effective thermal neutron shielding materials. (author)

  2. Spatial distribution of moderated neutrons along a Pb target irradiated by high-energy protons

    International Nuclear Information System (INIS)

    Fragopoulou, M.; Manolopoulou, M.; Stoulos, S.; Brandt, R.; Westmeier, W.; Kulakov, B.A.; Krivopustov, M.I.; Sosnin, A.N.; Debeauvais, M.; Adloff, J.C.; Zamani Valasiadou, M.

    2006-01-01

    High-energy protons in the range of 0.5-7.4 GeV have irradiated an extended Pb target covered with a paraffin moderator. The moderator was used in order to shift the hard Pb spallation neutron spectrum to lower energies and to increase the transmutation efficiency via (n,γ) reactions. Neutron distributions along and inside the paraffin moderator were measured. An analysis of the experimental results was performed based on particle production by high-energy interactions with heavy targets and neutron spectrum shifting by the paraffin. Conclusions about the spallation neutron production in the target and moderation through the paraffin are presented. The study of the total neutron fluence on the moderator surface as a function of the proton beam energy shows that neutron cost is improved up to 1 GeV. For higher proton beam energies it remains constant with a tendency to decline

  3. Modified paraffin wax for improvement of histological analysis efficiency.

    Science.gov (United States)

    Lim, Jin Ik; Lim, Kook-Jin; Choi, Jin-Young; Lee, Yong-Keun

    2010-08-01

    Paraffin wax is usually used as an embedding medium for histological analysis of natural tissue. However, it is not easy to obtain enough numbers of satisfactory sectioned slices because of the difference in mechanical properties between the paraffin and embedded tissue. We describe a modified paraffin wax that can improve the histological analysis efficiency of natural tissue, composed of paraffin and ethylene vinyl acetate (EVA) resin (0, 3, 5, and 10 wt %). Softening temperature of the paraffin/EVA media was similar to that of paraffin (50-60 degrees C). The paraffin/EVA media dissolved completely in xylene after 30 min at 50 degrees C. Physical properties such as the amount of load under the same compressive displacement, elastic recovery, and crystal intensity increased with increased EVA content. EVA medium (5 wt %) was regarded as an optimal composition, based on the sectioning efficiency measured by the numbers of unimpaired sectioned slices, amount of load under the same compressive displacement, and elastic recovery test. Based on the staining test of sectioned slices embedded in a 5 wt % EVA medium by hematoxylin and eosin (H&E), Masson trichrome (MT), and other staining tests, it was concluded that the modified paraffin wax can improve the histological analysis efficiency with various natural tissues. (c) 2010 Wiley-Liss, Inc.

  4. Radiometric determination of uniformity of putting paraffin on textile threads

    International Nuclear Information System (INIS)

    Ridel', Z.; Kherrmann, Eh.; Shefer, I.; Tseiner, A.

    1979-01-01

    To improve processing of the natural and synthetic fiber threads on stocking-frames, they are treated by paraffin. Paraffin is applied in the amounts nearly equal to 0.1 -1.0 g for 10 4 m of the thread's length. To determine amount of paraffin on thread and to determine uniformity if its application, a radiometric method has been developed. As a radioactive label, didocilephosphate of rare earths was used. This compound has good solubility in hydrocarbons and does not change physical properties of paraffin in the investigated field of its application as well as its concentration. It is possible to add to paraffin this radioactive label or a non-active label with subsequent its activation. Amount of paraffin, applied on a thread is determined by means of measurement of activity of thread samples of different length. Information about uniformity of paraffin application on thread have been obtained by means of autoradiography. It has been found that paraffin in mainly applied on the thread's bulges [ru

  5. Cleaning of paraffins and their microbiological transformation

    Energy Technology Data Exchange (ETDEWEB)

    Shakarashvili, T S; Bekauri, N G; Chubinidze, N G; Dididze, A V

    1982-01-01

    This paper provides a perfected technique for processing liquid C/sub 11/-C/sub 20/ alkanes extracted from Georgian oil (from the Samgori field). Utilizing this base, a biomass was derived with the aid of the Candida Guillermondy culture. The method for cleaning the paraffin complex with carbamide was simplified during the deparaffinization process of diesel fuel (fraction 200-300/sup 0/C) by application of a washing agent -petr. ether with a boiling temp. of 40-70/sup 0/C. The derived alkanes contained up to 0.2% of aromatic hydrocarbons. This eliminated the rather expensive and labor-intensive step in the dewaxing process -- adsorption chromatography. It was demonstrated that under optimal conditions the amount of cultured product was higher in n-alkanes from Samgori oil than from the petroleum utilized at the Akhmet biochemical plant.

  6. Modulated structure formation in demixing paraffin blends

    CERN Document Server

    Gilbert, E P

    2002-01-01

    Small angle scattering (SANS and SAXS) and differential scanning calorimetry have been measured from C sub 2 sub 8 :C sub 3 sub 6 normal paraffin mixtures of varying composition quenched from the melt. Satellite peaks are observed in the SAXS whose offset in Q, relative to Bragg diffraction peaks associated with the average structure, are composition dependent. The offset is close to the position of the most intense peak observed in SANS. Scattering from the quenched structures is consistent with a correlated displacement and substitutional disorder model yielding modulations that are incommensurate with the average lattice. DSC shows an additional endotherm in the mixtures that is not present in the pure components and is associated with this superstructure formation. (orig.)

  7. Modulated structure formation in demixing paraffin blends

    International Nuclear Information System (INIS)

    Gilbert, E.P.

    2002-01-01

    Small angle scattering (SANS and SAXS) and differential scanning calorimetry have been measured from C 28 :C 36 normal paraffin mixtures of varying composition quenched from the melt. Satellite peaks are observed in the SAXS whose offset in Q, relative to Bragg diffraction peaks associated with the average structure, are composition dependent. The offset is close to the position of the most intense peak observed in SANS. Scattering from the quenched structures is consistent with a correlated displacement and substitutional disorder model yielding modulations that are incommensurate with the average lattice. DSC shows an additional endotherm in the mixtures that is not present in the pure components and is associated with this superstructure formation. (orig.)

  8. Efficient filtration system for paraffin-catalyst slurry separation

    Directory of Open Access Journals (Sweden)

    Khodagholi Mohammad Ali

    2013-01-01

    Full Text Available The filtration efficiency for separating liquid paraffin (or water from a slurry consisting of 25 weight% spherical alumina in a Slurry Bubble Column Reactor (SBCR comprised of a cylindrical tube of 10 cm diameter and 150 cm length was studied. Various differential pressures (ΔP were applied to two separate tubular sintered metal stainless steel filter elements with nominal pore size of 4 and 16μm. The experimental results disclosed that the rate of filtrations increased on applying higher differential pressure to the filter element. Albeit this phenomenon is limited to moderate ΔPs and for ΔP more than 1 bar is neither harmful nor helpful. The highest filtration rates at ΔPs higher than 1 bar were 170 and 248 ml/minute for 4 and 16μm respectively. Using water as the liquid in slurry the rate of filtration enhanced to 4 folds, and this issue reveals impact of viscosity on filtration efficiency clearly. In all situations, the total amount of particles present in the filtrate part never exceeded a few parts per million (ppm. The statistical analysis of the SEM image of the filtrate indicated that by applying higher pressure difference to the filter element the frequency percent of larger particle size increases. The operation of filter cake removing was performed with back flashing of 300 ml of clean liquid with pressures of 3-5 bar of N2 gas.

  9. Binary liquid-liquid equilibria of aniline-paraffin and furfural-paraffin systems

    Energy Technology Data Exchange (ETDEWEB)

    Sen, S.C.; Maity, S.; Ganguli, K.; Ray, P. (Calcutta Univ., (India))

    1991-12-01

    Liquid-liquid-equilibria (L-L-E) of hydrocarbon containing systems are of considerable commercial importance to refineries. But prediction of L-L-E of such systems is extremely difficult owing to the complex nature of the petroleum fluids. For treating such complex mixtures, a continuous component method is appropriate and for representing such liquids, a group contribution model like the UNIFAC is extremely convenient. It is, however, necessary to determine the appropriate group interaction parameters, and also to test the applicability of the UNIFAC method to these cases. Binary liquid-liquid-equilibria data for several aniline-paraffin and furfural-paraffin systems have been taken. These data along with data for other aniline-hydrocarbon and furfural-hydrocarbon systems from literature have been correlated using the UNIFAC model. The UNIFAC group interaction parameters have been found to have a linear temperature dependence. The CH{sub 2} groups in cyclo and non-cyclo paraffins require different interaction parameters. It was also found that a scaling of the combinatorial term is necessary for higher molecular weight hydrocarbons. 13 refs., 12 figs., 5 tabs.

  10. Efficacy of paraffin wax bath for carpal tunnel syndrome: a randomized comparative study

    Science.gov (United States)

    Ordahan, Banu; Karahan, Ali Yavuz

    2017-12-01

    Carpal tunnel syndrome (CTS) is the most frequently diagnosed neuropathy of upper extremity entrapment neuropathies. We aimed to investigate the effectiveness of paraffin therapy in patients with CTS. Seventy patients diagnosed with mild or moderate CTS were randomly divided into two groups as splint treatment (during the night and day time as much as possible for 3 weeks) alone and splint (during the night and day time as much as possible for 3 weeks) + paraffin treatment (five consecutive days a week for 3 weeks). Clinical and electrophysiological assessments were performed before and 3 weeks after treatment. The patients were assessed by using visual analog scale (VAS) for pain, electroneuromyography (ENMG), and Boston Carpal Tunnel Syndrome Questionnaire (BCTSQ). The significant improvement was found in VAS scores in both groups when compared with pretreatment values ( p 0.05), whereas a significant improvement was noted in the BCTQ symptom severity scale score in the splint group ( p 0.05), and the difference in these parameters between the groups was statistically significant ( p Paraffin treatment with splint increases the recovery in functional and electrophysiological parameters.

  11. The moderator's moderator

    International Nuclear Information System (INIS)

    Williamson, G.K.

    1990-01-01

    A brief account is given of the development of graphite moderators for Magnox and advanced gas cooled reactors. The accident at Windscale in 1957 brought to worldwide attention the importance of irradiation damage in graphite and the consequent storage of Wigner energy. In spite of the Windscale setback, preparations for the civil programme of Magnox reactors went ahead apace. Some of the background to the disastrous Dungeness B tender is presented. In spite of all the difficulties and uncertainties, the graphite in UK reactors has performed well. In all cases, as far as the author is aware, the behaviour of the graphite moderators will not prevent design life being achieved. (author)

  12. Replacing xylene with n-heptane for paraffin embedding.

    Science.gov (United States)

    Stockert, J C; López-Arias, B; Del Castillo, P; Romero, A; Blázquez-Castro, A

    2012-10-01

    In standard histological technique, aromatic solvents such as xylene and toluene are used as clearing agents between ethanol dehydration and paraffin embedding. In addition, these solvents are used for de-waxing paraffin sections. Unfortunately, these solvents are harmful and therefore adequate substitutes would be useful. We suggest the use of n-heptane as a convenient substitute for xylene. Paraffin sections of rat tissues processed with n-heptane and stained with hematoxylin-eosin or Masson's trichrome showed proper embedment, well preserved morphology and excellent staining.

  13. Photothermally Driven Refreshable Microactuators Based on Graphene Oxide Doped Paraffin.

    Science.gov (United States)

    Hou, Sichao; Wang, Miao; Guo, Shouwu; Su, Ming

    2017-08-09

    Actuators based on phase change materials (paraffin) can simultaneously produce large stroke length and large force due to thermal expansion, but the low thermal conductivity of paraffin requires high power input and long actuation time. The graphene oxide (GO) doped paraffin dynamic actuator addresses the key challenges in the design of thermal phase change actuators: Thermal conductivity and light absorbing are increased, and the response time is reduced compared to the standard phase change actuator designed with metal heating resistors. The thermal properties of GO-paraffin composites with varied loading amount are characterized to confirm the optimal loading amount of 1.0%. A multicell phase change actuator was integrated into a digital micromirror controlled optical system. A series of photothermally driven refreshable patterns were generated and confirmed with infrared imaging.

  14. Effects of short-chain chlorinated paraffins on soil organisms.

    Science.gov (United States)

    Bezchlebová, Jitka; Cernohlávková, Jitka; Kobeticová, Klára; Lána, Jan; Sochová, Ivana; Hofman, Jakub

    2007-06-01

    Despite the fact that chlorinated paraffins have been produced in relatively large amounts, and high concentrations have been found in sewage sludge applied to soils, there is little information on their concentrations in soils and the effect on soil organisms. The aim of this study was to investigate the toxicity of chlorinated paraffins in soils. The effects of short-chain chlorinated paraffins (64% chlorine content) on invertebrates (Eisenia fetida, Folsomia candida, Enchytraeus albidus, Enchytraeus crypticus, Caenorhabditis elegans) and substrate-induced respiration of indigenous microorganisms were studied. Differences were found in the sensitivity of the tested organisms to short-chain chlorinated paraffins. F. candida was identified as the most sensitive organism with LC(50) and EC(50) values of 5733 and 1230 mg/kg, respectively. Toxicity results were compared with available studies and the predicted no effect concentration (PNEC) of 5.28 mg/kg was estimated for the soil environment, based on our data.

  15. resistant containers on the incidence of paraffin (kerosene)

    African Journals Online (AJOL)

    whether its use would decrease the incidence ofparaffin ingestion. ... education to prevent paraffin poisoning. S Atr Med J 1994; 84: ... organised poster competitions, and pamphlets with ... 2-litre plastic container designed according to the.

  16. Observations of radiation damage effects in paraffin and polyethylene crystals

    International Nuclear Information System (INIS)

    Petermann, J.; Gleiter, H.; Bochum Univ.

    1973-01-01

    A report is given on electron microscopic observations on n-paraffin and polyethylene monocrystals after irradiating with electrons. The observations show that the cross-links in n-paraffin monocrystals form agglomerates which preferably occur in the neighbourhood of lattice defects. In polyethylene monocrystals, the cross-links line up in long rows parallel to the [100] or [010] direction. (orig./LH) [de

  17. Combined in situ zymography, immunofluorescence, and staining of iron oxide particles in paraffin-embedded, zinc-fixed tissue sections.

    Science.gov (United States)

    Haeckel, Akvile; Schoenzart, Lena; Appler, Franziska; Schnorr, Joerg; Taupitz, Matthias; Hamm, Bernd; Schellenberger, Eyk

    2012-01-01

    Superparamagnetic iron oxide particles are used as potent contrast agents in magnetic resonance imaging. In histology, these particles are frequently visualized by Prussian blue iron staining of aldehyde-fixed, paraffin-embedded tissues. Recently, zinc salt-based fixative was shown to preserve enzyme activity in paraffin-embedded tissues. In this study, we demonstrate that zinc fixation allows combining in situ zymography with fluorescence immunohistochemistry (IHC) and iron staining for advanced biologic investigation of iron oxide particle accumulation. Very small iron oxide particles, developed for magnetic resonance angiography, were applied intravenously to BALB/c nude mice. After 3 hours, spleens were explanted and subjected to zinc fixation and paraffin embedding. Cut tissue sections were further processed to in situ zymography, IHC, and Prussian blue staining procedures. The combination of in situ zymography as well as IHC with subsequent Prussian blue iron staining on zinc-fixed paraffin-embedded tissues resulted in excellent histologic images of enzyme activity, protease distribution, and iron oxide particle accumulation. The combination of all three stains on a single section allowed direct comparison with only moderate degradation of fluorescein isothiocyanate-labeled substrate. This protocol is useful for investigating the biologic environment of accumulating iron oxide particles, with excellent preservation of morphology.

  18. Reliable PCR quantitation of estrogen, progesterone and ERBB2 receptor mRNA from formalin-fixed, paraffin-embedded tissue is independent of prior macro-dissection

    DEFF Research Database (Denmark)

    Tramm, Trine; Hennig, Guido; Kyndi, Marianne

    2013-01-01

    Gene expression analysis on messenger RNA (mRNA) purified from formalin-fixed, paraffin-embedded tissue is increasingly used for research purposes. Tissue heterogeneity may question specificity and interpretation of results from mRNA isolated from a whole slide section, and thresholds for minimal...... tumor content in the paraffin block or macrodissection are used to avoid contamination from non-neoplastic tissue. The aim was to test if mRNA from tissue surrounding breast cancer affected quantification of estrogen receptor α (ESR1), progesterone receptor (PGR) and human epidermal growth factor...... receptor 2 (ERBB2), by comparing gene expression from whole slide and tumor-enriched sections, and correlating gene expression from whole slide sections with corresponding immunohistochemistry. Gene expression, based on mRNA extracted from a training set (36 paraffin blocks) and two validation sets (133...

  19. Design and evaluation of a heat exchanger that uses paraffin wax and recycled materials as solar energy accumulator

    International Nuclear Information System (INIS)

    Reyes, Alejandro; Negrete, Daniela; Mahn, Andrea; Sepúlveda, Francisco

    2014-01-01

    Highlights: • Thermal conductivity of paraffin wax was improved with aluminum wool. • Aluminum wool surrounding the cans favored the energy recuperation from the wax. • The heat exchanger accumulated 3000 kJ energy. • The accumulated energy can be easily increased with larger units. • COMSOL simulated adequately the energy removal process from the cans. - Abstract: Soft drink cans filled with paraffin wax mixed with 5% w/w aluminum wool, obtained from disposable cans, doubled the thermal conductivity of cans filled only with paraffin wax. Thermal conductivity of the systems was determined by two ways: directly using a thermal conductivimeter, and indirectly based on temperature profiles and on the analytical solution of a cylinder. We designed, built and evaluated a heat exchanger for solar energy accumulation, composed by 48 disposable soft drink cans filled with a total of 9.5 kg of paraffin wax mixed with 5% w/w aluminum wool. In sunny days, the wax melted completely in 3 h. The accumulated energy of 3000 kJ, allowed increasing the temperature of 3.5 m 3 /h air flow rate from 20 to 40 °C during a period of 2 h. This application will allow extending the use of solar energy in drying processes or could be used as household calefaction system. The progress of the phase change front in time during the energy discharge period was simulated with COMSOL, whereas the effect of the number of cans and thermal conductivity of the paraffin wax on the air temperature increase was simulated with MATLAB

  20. Synthesis and application of polyaminoamide as new paraffin inhibitor from vegetable oil

    OpenAIRE

    Chen, Gang; Tang, Ying; Zhang, Jie

    2011-01-01

    Abstract In this work, a series of novel paraffin inhibitor, polyaminoamide (PAA), was designed and prepared by aminolysis and poly-condensation using soybean oil and canola oil as the raw material. The property of the PAAs as paraffin inhibitor was investigated, the results show several PAA samples are potent in paraffin inhibition, and PPC-2 is the most effective one. Besides, the paraffin crystal morphology analysis was carried out to provide the mechanism of paraffin inhibition.

  1. Effect of radiation on the crystals of polyethylene and paraffins

    International Nuclear Information System (INIS)

    Ungar, G.; Grubb, D.T.; Keller, A.

    1980-01-01

    Paraffins were irradiated with electrons in the electron microscope. The electron microscopic image and the electron diffraction patterns were followed as a function of dose. The objectives were: (a) to establish a connection between the 'polyethylene-type' and 'paraffin-like' behaviour and (b) to identify the phase segregation, by visual means. Increasing chain length, increasing dose rate and decreasing temperature individually and in combination, were found to favour the 'polyethylene-type' behaviour (crystal destruction through increasing lattice defects) while the reverse trend of the above three variables favoured the 'paraffin-like' behaviour (phase-segregated damaged and undamaged species). Segregated phases could in some circumstances be identified as non-diffracting 'droplets' within a crystalline matrix, with the lattice hardly affected, in the electron microscopic image. These droplets remain constant in number but increase in size as the irradiation progresses, the number of droplets depending on the chain length of the paraffin, on the irradiation temperature and on the dose rate. This behaviour, together with some further observations, reveals that the radiation-induced active species do not form crosslinks in situ but migrate over distances which can amount to μm. In contrast to the above, in the case of the lowest paraffin investigated, (C 23 H 48 ), the lattice became uniformly distorted as judged from the diffraction pattern, but the damage was observed to 'heal-out' with time. The results are discussed. (author)

  2. Evaluation of different tissue de-paraffinization procedures for infrared spectral imaging.

    Science.gov (United States)

    Nallala, Jayakrupakar; Lloyd, Gavin Rhys; Stone, Nicholas

    2015-04-07

    In infrared spectral histopathology, paraffin embedded tissues are often de-paraffinized using chemical agents such as xylene and hexane. These chemicals are known to be toxic and the routine de-waxing procedure is time consuming. A comparative study was carried out to identify alternate de-paraffinization methods by using paraffin oil and electronic de-paraffinization (using a mathematical computer algorithm) and their effectiveness was compared to xylene and hexane. Sixteen adjacent tissue sections obtained from a single block of a normal colon tissue were de-paraffinized using xylene, hexane and paraffin oil (+ hexane wash) at five different time points each for comparison. One section was reserved unprocessed for electronic de-paraffinization based on a modified extended multiplicative signal correction (EMSC). IR imaging was carried out on these tissue sections. Coefficients based on the fit of a pure paraffin model to the IR images were then calculated to estimate the amount of paraffin remaining after processing. Results indicate that on average xylene removes more paraffin in comparison to hexane and paraffin oil although the differences were small. This makes paraffin oil, followed by a hexane wash, an interesting and less toxic alternative method of de-paraffinization. However, none of the chemical methods removed paraffin completely from the tissues at any given time point. Moreover, paraffin was removed more easily from the glandular regions than the connective tissue regions indicating a form of differential paraffin retention based on the histology. In such cases, the use of electronic de-paraffinization to neutralize such variances across different tissue regions might be considered. Moreover it is faster, reduces scatter artefacts by index matching and enables samples to be easily stored for further analysis if required.

  3. The effects of normal paraffins mobilizers on irradiated polypropylene

    International Nuclear Information System (INIS)

    Chen Wenxiu; Gao Ling

    1995-01-01

    The n-paraffins blended with polypropylene (PP) as mobilizer had been investigated. The effectiveness of mobilizer (n-paraffins) on irradiated polypropylene is dependent on the molecular weight of mobilizer and its content on polypropylene. The n-docosame (n-C 22 ) possesses the best effectiveness of radiation tolerance on PP among the mobilizer paraffins: n-decane (n-C 10 ), n-hexadecane (n-C 16 ), n-docosane (n-C 22 ) and n-hexatriacontane (n-C 36 ). The 2% (w/w) content of a given mobilizer is the most effective at reducing the embrittlement of irradiated PP as evidenced by the elongation at break. The physical properties of polypropylene with mobilizers such as density, Young's modulus, the Fraction of free volume and the weight swelling ratio in p-xylene at room temperature were measured. Above phenomena are related with the constructive of blended PP and demonstrated by its physical properties

  4. Reduction in spasticity in stroke patient with paraffin therapy.

    Science.gov (United States)

    Wang, Jing; Yu, Peng; Zeng, Ming; Gu, Xudong; Liu, Yan; Xiao, Mingyue

    2017-01-01

    The aim of the study was to confirm whether paraffin therapy offer clinical value in the treatment of spasticity due to stroke. Fifty-two patients with spasticity in the upper limb were included. The patients were randomized into the experimental group with paraffin therapy (n = 27) and the control group with placebo therapy (n = 25). The outcome measures besides temperature examination were undertaken at time points of 0 (T0), 2 (T1) and 4 weeks (T2) following therapy treatment. The extent of spasticity was measured using Modified Ashworth Score (MAS) during passive movement at the shoulder, elbow, wrist and finger joints. Visual analogue scale (VAS) was used to evaluate the hemiplegic upper limb pain and functional activity of the upper limb motor function was evaluated by Brunnstrom recovery stage. All adverse events were recorded. MAS decreased significantly in Exp group compared with Con group, at the time points of T1 and T2, both before and immediately after paraffin therapy. Paraffin treatment failed to show remarkable improvement in pain compared with placebo-treated patient at movement at any time point. But VAS in Exp exhibited a tendency to decrease over time in shoulder, elbow, wrist and hand. With regard to the Brunnstrom score, patients in Exp showed significant improvement at the end of trial compared to the beginning. The values of temperature showed significant increment immediately after paraffin therapy at each time point in Exp group. Paraffin therapy may be a kind of noninvasive, promising method to reduce spasticity of stroke patients.

  5. Magnetic orientation of paraffin in a magnetic levitation furnace

    Science.gov (United States)

    Takahashi, K.; Umeki, C.; Mogi, I.; Koyama, K.; Awaji, S.; Motokawa, M.; Watanabe, K.

    2004-04-01

    Containerless melting of paraffin under a magnetic levitation condition has been performed by using a cryogen-free hybrid magnet and two kinds of laser furnaces. One is local irradiation of CO 2 laser light at the top of the sample. The other is homogeneous irradiation of YAG laser light with a concave ring mirror. In the latter case, reduction of the Marangoni convection on the surface of the sample and the magnetic orientation of paraffin molecules were observed. The magnetic anisotropy of the spherical sample was confirmed by the measurement of magnetization and X-ray diffraction.

  6. Magnetic orientation of paraffin in a magnetic levitation furnace

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, K.; Umeki, C.; Mogi, I.; Koyama, K.; Awaji, S.; Motokawa, M.; Watanabe, K

    2004-04-30

    Containerless melting of paraffin under a magnetic levitation condition has been performed by using a cryogen-free hybrid magnet and two kinds of laser furnaces. One is local irradiation of CO{sub 2} laser light at the top of the sample. The other is homogeneous irradiation of YAG laser light with a concave ring mirror. In the latter case, reduction of the Marangoni convection on the surface of the sample and the magnetic orientation of paraffin molecules were observed. The magnetic anisotropy of the spherical sample was confirmed by the measurement of magnetization and X-ray diffraction.

  7. Magnetic orientation of paraffin in a magnetic levitation furnace

    International Nuclear Information System (INIS)

    Takahashi, K.; Umeki, C.; Mogi, I.; Koyama, K.; Awaji, S.; Motokawa, M.; Watanabe, K.

    2004-01-01

    Containerless melting of paraffin under a magnetic levitation condition has been performed by using a cryogen-free hybrid magnet and two kinds of laser furnaces. One is local irradiation of CO 2 laser light at the top of the sample. The other is homogeneous irradiation of YAG laser light with a concave ring mirror. In the latter case, reduction of the Marangoni convection on the surface of the sample and the magnetic orientation of paraffin molecules were observed. The magnetic anisotropy of the spherical sample was confirmed by the measurement of magnetization and X-ray diffraction

  8. Spectral distribution measurements of neutrons in paraffin borax mixtures

    International Nuclear Information System (INIS)

    El-Khatib, A.M.; Gaber, M.; Abou El-Khier, M.A.

    1987-01-01

    Neutron fluxes from a compact D-T neutron source has been measured in paraffin-borax mixtures by using activation foil detectors with successive threshold energies. The absorbed doses, backscattering coefficients and build-up factors were determined as well. The contribution of thermal and intermediate neutron dose is much lower, compared to that of fast neutrons. Among the used mediums, paraffin loaded with 4% borax concentration was found to be the best absorbing medium against neutrons at near depths within the blocks, while at a depth around 12 cm the neutron absorption (or scattering) is independent on the type of the used medium. (author)

  9. Purity of paraffins used in drugs and cosmetics

    Energy Technology Data Exchange (ETDEWEB)

    Monarca, S; Fagioli, F; Morozzi, G

    1981-01-01

    A previously developed technique for the determination of polycyclic aromatic hydrocarbons (PAH's) in purified petroleum products was applied to some fully-refined paraffin samples for cosmetic and medicinal uses. The analytical procedure provided identification and quantitative assay for ng/g amounts of two well known carcinogenic PAH's, benzo-a-pyrene and benzoflouranthene. The method is compared with rapid pharmacopoeial tests based on different quality criteria. A lack of agreement between PAH content in paraffin samples and the results of the pharmacopoeial tests was noted. (1 diagram, 49 references, 5 tables)

  10. From an equilibrium based MOF adsorbent to a kinetic selective carbon molecular sieve for paraffin/iso-paraffin separation

    KAUST Repository

    Li, Baiyan

    2016-11-04

    We unveil a unique kinetic driven separation material for selectively removing linear paraffins from iso-paraffins via a molecular sieving mechanism. Subsequent carbonization and thermal treatment of CD-MOF-2, the cyclodextrin metal-organic framework, afforded a carbon molecular sieve with a uniform and reduced pore size of ca. 5.0 Å, and it exhibited highly selective kinetic separation of n-butane and n-pentane from iso-butane and iso-pentane, respectively. © The Royal Society of Chemistry.

  11. Paraffin ingestion - the problem | Ellis | South African Medical Journal

    African Journals Online (AJOL)

    An effective durable, low-cost child-resistant container which is easy to pour from should be made available by petroleum companies and/or entrepreneurs and distributed through their network. This should be combined with health education on the danger of paraffin. Health care workers and administrators should be made ...

  12. Quantifying Short-Chain Chlorinated Paraffin Congener Groups

    NARCIS (Netherlands)

    Yuan, Bo; Bogdal, Christian; Berger, Urs; MacLeod, Matthew; Gebbink, Wouter A.; Alsberg, Tomas; Wit, de Cynthia A.

    2017-01-01

    Accurate quantification of short-chain chlorinated paraffins (SCCPs) poses an exceptional challenge to analytical chemists. SCCPs are complex mixtures of chlorinated alkanes with variable chain length and chlorination level; congeners with a fixed chain length (n) and number of chlorines (m) are

  13. Resettable binary latch mechanism for use with paraffin linear motors

    Science.gov (United States)

    Maus, Daryl; Tibbitts, Scott

    1991-01-01

    A new resettable Binary Latch Mechanism was developed utilizing a paraffin actuator as the motor. This linear actuator alternately latches between extended and retracted positions, maintaining either position with zero power consumption. The design evolution and kinematics of the latch mechanism are presented, as well as the development problems and lessons that were learned.

  14. The measurements of thermal neutron flux distribution in a paraffin

    Indian Academy of Sciences (India)

    The term `thermal flux' implies a Maxwellian distribution of velocity and energy corresponding to the most probable velocity of 2200 ms-1 at 293.4 K. In order to measure the thermal neutron flux density, the foil activation method was used. Thermal neutron flux determination in paraffin phantom by counting the emitted rays of ...

  15. Extracorporeal membrane oxygenation after intravenous injection of paraffin oil

    DEFF Research Database (Denmark)

    Pasgaard, Thomas; Huynh, Anh-Nhi Thi; Gjedsted, Jakob

    2016-01-01

    We present a rare cause of acute respiratory distress syndrome (ARDS) due to an accidental intravascular injection of paraffin oil. While there is no specific therapy, we decided to support the patient with veno-venous extracorporeal membrane oxygenation (V-V ECMO) to allow the ARDS to resolve. A...

  16. Bismuth toxicity in patients treated with bismuth iodoform paraffin packs.

    Science.gov (United States)

    Atwal, A; Cousin, G C S

    2016-01-01

    Bismuth is a heavy metal used in bismuth iodoform paraffin paste (BIPP) antiseptic dressings and in a number of other medical preparations. It can be absorbed systemically and cause toxicity. We report 2 cases of such neurotoxicity after it was used in operations on the jaws. Copyright © 2015. Published by Elsevier Ltd.

  17. Organic Rankine Cycle with Solar Heat Storage in Paraffin Way

    Directory of Open Access Journals (Sweden)

    Constantin LUCA

    2015-06-01

    Full Text Available The paper presents an electricity generation system based on an Organic Rankine Cycle and proposed storing the amount of the heat produced by the solar panels using large volume of paraffin wax. The proposed working fluid is R-134a refrigerant. The cycle operates at very low temperatures. A efficiency of 6,55% was obtained.

  18. Study on Thermal Degradation Characteristics and Regression Rate Measurement of Paraffin-Based Fuel

    Directory of Open Access Journals (Sweden)

    Songqi Hu

    2015-09-01

    Full Text Available Paraffin fuel has been found to have a regression rate that is higher than conventional HTPB (hydroxyl-terminated polybutadiene fuel and, thus, presents itself as an ideal energy source for a hybrid rocket engine. The energy characteristics of paraffin-based fuel and HTPB fuel have been calculated by the method of minimum free energy. The thermal degradation characteristics were measured for paraffin, pretreated paraffin, HTPB and paraffin-based fuel in different working conditions by the using differential scanning calorimetry (DSC and a thermogravimetric analyzer (TGA. The regression rates of paraffin-based fuel and HTPB fuel were tested by a rectangular solid-gas hybrid engine. The research findings showed that: the specific impulse of paraffin-based fuel is almost the same as that of HTPB fuel; the decomposition temperature of pretreated paraffin is higher than that of the unprocessed paraffin, but lower than that of HTPB; with the increase of paraffin, the initial reaction exothermic peak of paraffin-based fuel is reached in advance, and the initial reaction heat release also increases; the regression rate of paraffin-based fuel is higher than the common HTPB fuel under the same conditions; with the increase of oxidizer mass flow rate, the regression rate of solid fuel increases accordingly for the same fuel formulation.

  19. Rheology of petrolatum-paraffin oil mixtures : Applications to analogue modelling of geological processes

    NARCIS (Netherlands)

    Duarte, João C.; Schellart, Wouter P.; Cruden, Alexander R.

    2014-01-01

    Paraffins have been widely used in analogue modelling of geological processes. Petrolatum and paraffin oil are commonly used to lubricate model boundaries and to simulate weak layers. In this paper, we present rheological tests of petrolatum, paraffin oil and several homogeneous mixtures of the two.

  20. Fluorescence in situ hybridization on formalin-fixed and paraffin-embedded tissue

    DEFF Research Database (Denmark)

    Laub Petersen, Bodil; Zeuthen, Mette Christa; Pedersen, Sanni

    2004-01-01

    , such as quantitation of signals as in triploidy, it is possible to isolate nuclei from paraffin-embedded tissue. However, using formalin-fixed paraffin-embedded tissue, either in thin sections or as isolated nuclei, one encounters a range of technical problems, paralleling those met in immunohistochemistry. Variations...... nuclei and tissue sections from formalin-fixed, paraffin-embedded tissue....

  1. Circumstances surrounding aneurysmal subarachnoid hemorrhage

    NARCIS (Netherlands)

    Schievink, W. I.; Karemaker, J. M.; Hageman, L. M.; van der Werf, D. J.

    1989-01-01

    The circumstances surrounding aneurysmal subarachnoid hemorrhage were investigated in a group of 500 consecutive patients admitted to a neurosurgical center. Subarachnoid hemorrhage occurred during stressful events in 42.8% of the patients, during nonstrenuous activities in 34.4%, and during rest or

  2. Radiotherapic Valuation of Paraffin Wax for Patients with Oral Cancer

    Energy Technology Data Exchange (ETDEWEB)

    Na, Kyung Su; Seo, Seuk Jin; Lee, Je Hee; Yoo, Sook Heun [Dept. of Radiation Oncology, Seoul National University Hosdital, Seoul (Korea, Republic of)

    2011-03-15

    This study is designed to investigate radiotherapic valuation of Paraffin Wax, which is newly formed for this study and generally utilized in dentistry, and Mouth Piece and Putty impression, which are commonly used in radiotherapy, for oral cavity as a compensator. Each compensator was formed by 10 x 10 x 1 cm and measured radiation dose attenuation ratio with reference of water phantom which is made of tissue-equivalent materials. Two patients with oral cancer underwent DRR (Digitally Reconstructed Radiogrph) of Offline Review Program of Aria System and Portal vision for 5 times for each material to evaluate reproducibility by each filling materials. Moreover, MU (monitor unit) changes by dose absorption were considered in the case of inevitable implication of an filling materials in the range for radiotherapy. Radiation dose attenuation ratios were shown -0.7{approx}+3.7% for Mouth Piece, +0.21{approx}+0.39% for Paraffin Wax and -2.71{approx}-1.76% for Putty impression. Error ranges of reproducibility of positions were measured {+-}3 mm for Mouth Piece, {+-}2 mm for Paraffin Wax and {+-}2 mm for Putty impression. Difference of prescription MU from dose absorption with an filling material increased +7.8% (250 MU) in Putty impression and -0.9% (230 MU) in Paraffin Wax as converted into a percentage from the standard phantom, Water 232 MU. Dose reduction of boundary between cavity and tissue was observed for Mouth Piece. Mouth Piece also had low reproducibility of positions as it had no reflection of anatomy of oral cavity even though it was a proper material to separate Maxilla and Mandible during therapy. On the other hand, Putty impression was a suitable material to correctly re-position oral cavity as before. However, it risked normal tissues getting unnecessary over irradiation and it caused radiation dose decrease by -2.5% for 1cm volume in comparison of it of water phantom. Dose reduction in Paraffin Wax, Fat Tissue-Equivalent Material, was smaller than other

  3. Radiotherapic Valuation of Paraffin Wax for Patients with Oral Cancer

    International Nuclear Information System (INIS)

    Na, Kyung Su; Seo, Seuk Jin; Lee, Je Hee; Yoo, Sook Heun

    2011-01-01

    This study is designed to investigate radiotherapic valuation of Paraffin Wax, which is newly formed for this study and generally utilized in dentistry, and Mouth Piece and Putty impression, which are commonly used in radiotherapy, for oral cavity as a compensator. Each compensator was formed by 10 x 10 x 1 cm and measured radiation dose attenuation ratio with reference of water phantom which is made of tissue-equivalent materials. Two patients with oral cancer underwent DRR (Digitally Reconstructed Radiogrph) of Offline Review Program of Aria System and Portal vision for 5 times for each material to evaluate reproducibility by each filling materials. Moreover, MU (monitor unit) changes by dose absorption were considered in the case of inevitable implication of an filling materials in the range for radiotherapy. Radiation dose attenuation ratios were shown -0.7∼+3.7% for Mouth Piece, +0.21∼+0.39% for Paraffin Wax and -2.71∼-1.76% for Putty impression. Error ranges of reproducibility of positions were measured ±3 mm for Mouth Piece, ±2 mm for Paraffin Wax and ±2 mm for Putty impression. Difference of prescription MU from dose absorption with an filling material increased +7.8% (250 MU) in Putty impression and -0.9% (230 MU) in Paraffin Wax as converted into a percentage from the standard phantom, Water 232 MU. Dose reduction of boundary between cavity and tissue was observed for Mouth Piece. Mouth Piece also had low reproducibility of positions as it had no reflection of anatomy of oral cavity even though it was a proper material to separate Maxilla and Mandible during therapy. On the other hand, Putty impression was a suitable material to correctly re-position oral cavity as before. However, it risked normal tissues getting unnecessary over irradiation and it caused radiation dose decrease by -2.5% for 1cm volume in comparison of it of water phantom. Dose reduction in Paraffin Wax, Fat Tissue-Equivalent Material, was smaller than other impressions and

  4. Preparation and Characterization of Modified Montmorillonite/Paraffin Phase Change Microcapsules for Energy Storage

    Directory of Open Access Journals (Sweden)

    LIN Sen

    2017-03-01

    Full Text Available The phase change microcapsules of modified montmorillonite/paraffin were prepared by Pickering emulsion method. Analytic techniques of optical microscopy, scanning electron microscopy(SEM, infrared spectroscopy(FTIR, differential scanning calorimetry(DSC and thermogravimetry(TG were utilized for characterizing chemical structure, morphology and thermal properties. Results show that modified montmorillonite as a new type wall material has excellent performance for protecting core material of paraffin. FTIR spectra of phase change of modified montmorillonite/paraffin microcapsules shows that their characteristic peaks match with corresponding peaks of pure paraffin and modified montmorillonite. DSC results indicate that modified montmorillonite/paraffin microcapsules have similar solid-liquid phase change temperature with pure paraffin. The phase transition enthalpy values of microcapsules with paraffin contents varying from 55% to 80% are 110.5-147.2J/g, indicating that microcapsules have excellent thermal storage performance and the phase change properties can be adjusted by changing contents of paraffin. TG results confirm that modified montmorillonite/paraffin microcapsules have outstanding thermal stability. The presented study indicates that modified montmorillonite is a suitable wall material for preparing paraffin microcapsule. Modified montmorillonite/paraffin microcapsules have advantages of low cost and high performance with a great application potential in the field of thermal storage.

  5. Preparation and thermal energy storage properties of paraffin/expanded graphite composite phase change material

    International Nuclear Information System (INIS)

    Zhang, Zhengguo; Zhang, Ni; Peng, Jing; Fang, Xiaoming; Gao, Xuenong; Fang, Yutang

    2012-01-01

    Highlights: ► EG was obtained by microwave irradiation to prepare the paraffin/EG composite PCM. ► Composite PCM was characterized by XRD to investigate the chemical compatibility. ► Temperature profiles of the composite PCM were obtained during thermal energy storage. -- Abstract: The paraffin/expanded graphite (EG) composite phase change material (PCM) was prepared by absorbing liquid paraffin into EG, in which paraffin was chosen as the PCM. EG was produced by microwave irradiation performed at room temperature. It was found that the EG prepared at 800 W irradiation power for 10 s exhibited the maximum sorption capacity of 92 wt% for paraffin. Scanning electron microscopy images showed that paraffin was uniformly dispersed in the pores of EG. Differential scanning calorimeter analysis indicated that the melting temperature of the composite PCM was close to that of paraffin, and its latent heat was equivalent to the calculated value based on the mass fraction of paraffin in the composite. X-ray diffraction analysis showed that the composite PCM was just a combination of paraffin with EG, and no new substance was produced. Thermal energy storage performance of the composite PCM was tested in a latent thermal energy storage (LTES) system. Transients of axial and radial temperature profiles were obtained in the LTES for the composite PCM and paraffin. The thermal energy storage charging duration for the composite PCM was reduced obviously compared to paraffin.

  6. Use of surfactants in cleaning paraffin from oil wells

    Energy Technology Data Exchange (ETDEWEB)

    Liebold, G; Rehberg, W

    1969-05-01

    The use of surfactants is described especially oxethylated alkylphenols, in the cleaning of oil wells from paraffin. Aqueous 1 or 10% solutions of the surfactant were injected into the well through the annulus, partially in combination with demulsifiers (for example Separol-brands of BASF). Injection was accomplished continuously or in intervals; in the beginning of 50 ppm surfactant, afterward 15 to 30 ppm as related to the wet crude was necessary. Efficiency of the treatment could be proved by the decrease of pressure in the pipes, the loosening of paraffin shells, and considerably prolonged operation periods in wells which otherwise would have come to a standstill. In quite a number of wells, treatment with hot oil and electric heating could be completely replaced by injection of surfactants. (11 refs.)

  7. Gas condensate--raw material for producing liquid paraffin hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Aliyeva, R.B.; Alikishi-Zade, G.Yu.; Kuliyev, A.M.; Leonidov, A.N.; Pereverzev, A.N.

    1980-01-01

    The problem of efficient utilization of gas condensates as raw material for removal of a valuable product, liquid paraffins, is examined. A classification of gas condensates is given which is used as raw material for removing these hydrocarbons: gas condensate with high content of n-alkanes (25-40 mass percent), with average content (18-25 mass percent), with low content (12-18 mass percent), light weight fractions compositions, which do not contain fractions up to 200/sup 0/, and also, content ofless than 12% n-alkanes. Gas condensate I-III groups are 30% of the total reserve of gas condensate. Liquid paraffins hydrocarbons, produced from fractions of diesel fuel, which has been removed from Shatlyk gas condensate under conditions which simulate virtual processes of caramide deparaffinization meet all requirements without additional refining.

  8. Oils; lubricants; paraffin-wax compositions; hydrocarbon condensation products

    Energy Technology Data Exchange (ETDEWEB)

    1934-04-04

    Petroleum hydrocarbons such as gasoline, kerosene, Diesel fuel oil, lubricating-oil, and paraffin wax, and like hydrocarbons such as are obtainable from shale oil and by the hydrogenation of carbonaceous materials, are improved by addition of products obtained by condensing a cyclic hydrocarbon with a saturated dihalogen derivative of an aliphatic hydrocarbon containing less than five carbon atoms. The addition of the condensation products increases the viscosity of the hydrocarbon oils specified, and is particularly useful in the case of lubricating-oils; addition of the condensation products to paraffin wax increases the transparency and adherent properties of the wax, and is useful in the manufacture of moulded articles such as candles; the products may also be used in solid lubricating-compositions.

  9. Romanian plant produces protein concentrate from paraffin-nourished yeasts

    Energy Technology Data Exchange (ETDEWEB)

    1985-01-01

    One of the world's few factories in which proteins are produced by continuous biotechnology is located in Romania. Here, at the bioproteins plant, microorganisms are converted into a flour which contains a protein concentrate that is so essential to the fattening of swine, cattle, sheep, fowl, and fish. These microorganisms are Candida type yeasts. The culture medium in which they are grown contains sulfates and phosphates. Paraffin, a petroleum product, supplies the carbon that is essential to the microorganisms viability.

  10. Paraffin scintillator for radioassay of solid support samples

    International Nuclear Information System (INIS)

    Fujii, Haruo; Takiue, Makoto

    1989-01-01

    A new paraffin scintillator used for solid support sample counting has been proposed, and its composition and various characteristics are described. The solid support sample treated with this scintillator can be easily handled because of rigid sample conditions. This technique provides great advantages such as the elimination of a large volume of scintillator and little radioactive waste material by using an economical polyethylene bag instead of the conventional counting vial. (author)

  11. Process for paraffin isomerization of a distillate range hydrocarbon feedstock

    Energy Technology Data Exchange (ETDEWEB)

    Chen, N.Y.; Garwood, W.E.; McCullen, S.B.

    1993-01-19

    Various catalytic processes have been proposed to isomerize n-paraffins so as to lower the pour point of distillate range hydrocarbon feedstocks. However, many available feedstocks contain nitrogen impurities which tend to poison conventional paraffin isomerization catalysts. A process has been developed to obviate or alleviate this problem. According to the invention, the paraffin-containing feedstock is contacted with a crystalline aluminosilicate zeolite catalyst having pore openings defined by a ratio of sorption of n-hexane to o-xylene of over 3 vol % and the ability to crack 3-methylpentane in preference to 2,3 dimethylbutane under defined conditions. The zeolite catalyst includes a Group VIII metal and has a zeolite SiO[sub 2]/Al[sub 2]O[sub 3] ratio of at least 20:1. The contacting is carried out at 199-454 C and a pressure of 100-1,000 psig, preferably 250-600 psig. The group of medium pore zeolites which can be used in the process of the invention includes ZSM-22, ZSM-23, and ZSM-35. The Group VIII metals used in the catalyst are preferably selected from Pt, Pd, Ir, Os, Rh, and Ru and the metal is preferably incorporated into the zeolite by ion exchange up to a metal content of preferably 0.1-3 wt %. Experiments are described to illustrate the invention. 1 tab.

  12. Automatic Measuring System for Oil Stream Paraffin Deposits Parameters

    Science.gov (United States)

    Kopteva, A. V.; Koptev, V. Yu

    2018-03-01

    This paper describes a new method for monitoring oil pipelines, as well as a highly efficient and automated paraffin deposit monitoring method. When operating oil pipelines, there is an issue of paraffin, resin and salt deposits on the pipeline walls that come with the oil stream. It ultimately results in frequent transportation suspension to clean or even replace pipes and other equipment, thus shortening operation periods between repairs, creating emergency situations and increasing production expenses, badly affecting environment, damaging ecology and spoil underground water, killing animals, birds etc. Oil spills contaminate rivers, lakes, and ground waters. Oil transportation monitoring issues are still subject for further studying. Thus, there is the need to invent a radically new automated process control and management system, together with measurement means intellectualization. The measurement principle is based on the Lambert-Beer law that describes the dependence between the gamma-radiation frequency and the density together with the linear attenuation coefficient for a substance. Using the measuring system with high accuracy (± 0,2%), one can measure the thickness of paraffin deposits with an absolute accuracy of ± 5 mm, which is sufficient to ensure reliable operation of the pipeline system. Safety is a key advantage, when using the proposed control system.

  13. Evaluation of performance loss of paraffin oil loaded filtering facepieces.

    Science.gov (United States)

    Tombolini, Francesca; Listrani, Stefano; Campopiano, Antonella; Plebani, Carmela

    2016-01-01

    Penetration measurements through commercially available filtering facepieces were performed with monodisperse DEHS aerosols ranging from 0.03 μm to 0.40 μm (either singly charged or neutralized), before and after 500 mg of paraffin oil loading. The distinct behavior of Coulomb and polarization capture efficiency is studied: as in the case of non loading also in the case of loading 500 mg of paraffin oil, the electrostatic capture mechanisms are mainly due to the Coulomb contribution up to aerosol particle diameter of about 0.10 μm, just when the polarization contribution becomes substantial. Both Coulomb and polarization capture mechanisms are influenced by the presence of 500 mg of paraffin oil, resulting less effective than the oil unloaded case of about 12% and 11%, respectively. By the occupational hygiene point of view, there is a degradation in the filter performance due to oil loading that the user does not realize because there is no remarkable variation in the breathing resistance.

  14. Opportunity's Surroundings on Sol 1818

    Science.gov (United States)

    2009-01-01

    NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,818th Martian day, or sol, of Opportunity's surface mission (March 5, 2009). South is at the center; north at both ends. The rover had driven 80.3 meters (263 feet) southward earlier on that sol. Tracks from the drive recede northward in this view. The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock. This view is presented as a cylindrical projection with geometric seam correction.

  15. Study on paraffin/expanded graphite composite phase change thermal energy storage material

    International Nuclear Information System (INIS)

    Zhang Zhengguo; Fang Xiaoming

    2006-01-01

    A paraffin/expanded graphite composite phase change thermal energy storage material was prepared by absorbing the paraffin into an expanded graphite that has an excellent absorbability. In such a composite, the paraffin serves as a latent heat storage material and the expanded graphite acts as the supporting material, which prevents leakage of the melted paraffin from its porous structure due to the capillary and surface tension forces. The inherent structure of the expanded graphite did not change in the composite material. The solid-liquid phase change temperature of the composite PCM was the same as that of the paraffin, and the latent heat of the paraffin/expanded graphite composite material was equivalent to the calculated value based on the mass ratio of the paraffin in the composite. The heat transfer rate of the paraffin/expanded graphite composite was obviously higher than that of the paraffin due to the combination with the expanded graphite that had a high thermal conductivity. The prepared paraffin/expanded graphite composite phase change material had a large thermal storage capacity and improved thermal conductivity and did not experience liquid leakage during its solid-liquid phase change

  16. Opportunity's Surroundings on Sol 1687

    Science.gov (United States)

    2009-01-01

    NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this 360-degree view of the rover's surroundings on the 1,687th Martian day, or sol, of its surface mission (Oct. 22, 2008). Opportunity had driven 133 meters (436 feet) that sol, crossing sand ripples up to about 10 centimeters (4 inches) tall. The tracks visible in the foreground are in the east-northeast direction. Opportunity's position on Sol 1687 was about 300 meters southwest of Victoria Crater. The rover was beginning a long trek toward a much larger crater, Endeavour, about 12 kilometers (7 miles) to the southeast. This view is presented as a cylindrical projection with geometric seam correction.

  17. Opportunity's Surroundings on Sol 1798

    Science.gov (United States)

    2009-01-01

    NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this 180-degree view of the rover's surroundings during the 1,798th Martian day, or sol, of Opportunity's surface mission (Feb. 13, 2009). North is on top. The rover had driven 111 meters (364 feet) southward on the preceding sol. Tracks from that drive recede northward in this view. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock. This view is presented as a cylindrical projection with geometric seam correction.

  18. Thermophysical properties estimation of paraffin/graphite composite phase change material using an inverse method

    International Nuclear Information System (INIS)

    Lachheb, Mohamed; Karkri, Mustapha; Albouchi, Fethi; Mzali, Foued; Nasrallah, Sassi Ben

    2014-01-01

    Highlights: • Preparation of paraffin/graphite composites by uni-axial compression technique. • Measurement of thermophysical properties of paraffin/graphite using the periodic method. • Measurement of the experimental densities of paraffin/graphite composites. • Prediction of the effective thermal conductivity using analytical models. - Abstract: In this paper, two types of graphite were combined with paraffin in an attempt to improve thermal conductivity of paraffin phase change material (PCM): Synthetic graphite (Timrex SFG75) and graphite waste obtained from damaged Tubular graphite Heat Exchangers. These paraffin/graphite phase change material (PCM) composites are prepared by the cold uniaxial compression technique and the thermophysical properties were estimated using a periodic temperature method and an inverse technique. Results showed that the thermal conductivity and thermal diffusivity are greatly influenced by the graphite addition

  19. Moderate Bravery

    DEFF Research Database (Denmark)

    Majgaard, Klaus

    2016-01-01

    Purpose: The ability to act in a purposeful and effective way amid institutional tensions and paradoxes is, right now, a highly prized quality in public leadership. The purpose of this chapter is to qualify moderately brave acts as a learning format that combines the analytical and performative...

  20. The use of naturally occurring selectively isolated bacteria for inhibiting paraffin deposition

    Energy Technology Data Exchange (ETDEWEB)

    Lazar, I.; Voicu, A.; Dobrota, S.; Petrisor, I.G.; Stefanescu, M.; Sandulescu, L. [Institute of Biology of the Romanian Academy, Spl. Independentei 296, Bucharest (Romania); Nicolescu, C.; Mucenica, D. [PETROSTAR Ploiesti, Bdul Bucuresti 35, Ploiesti (Romania)

    1999-01-01

    One of the most severe problems at any oil fields producing paraffinic oils is that of paraffin depositions. Romania which has a long experience in oil production is also faced with this problem in many oil fields. The microbial treatment, based on the activity of naturally occurring, selectively isolated bacteria, is already proved as an effective alternative to conventional methods to prevent and remove paraffin damage. Using such kind of bacterial products, exciting results for inhibiting paraffin depositions have been obtained. In this paper results concerning the naturally occurring bacteria selectively isolated from hydrocarbon polluted sites as well as from paraffinic oils, semi-solid and solid paraffin depositions are presented. After a laboratory screening, 15 bacterial strains (BS 1-15), three bacterial consortia (BC 1-3) and a Special Bacterial Consortium (SBC1) were selected. For the selection of bacterial consortia, the classical enrichment culture method has been used. The Special Bacterial Consortium resulted from a mixture of BS 1-15 and BC 1-3 following the steps of the classical enrichment culture method. The BS 1-15, BC 1-3 and SBC1 have been tested for their performances in producing biosurfactants and biosolvents as well as for hydrocarbon utilisation. The SBC1 has been tested for its ability in degradation of hydrocarbons contained in several types of paraffinic or non-paraffinic oils, and then for inhibiting paraffin deposition on a `flow equipment` using two types of paraffinic oils. The SBC1 has been also tested for degradation of hydrocarbons contained in semi-solid and solid paraffin depositions. The results obtained could support further applications to prevent and control paraffin depositions

  1. The use of naturally occurring selectively isolated bacteria for inhibiting paraffin deposition

    International Nuclear Information System (INIS)

    Lazar, I.; Voicu, A.; Dobrota, S.; Petrisor, I.G.; Stefanescu, M.; Sandulescu, L.; Nicolescu, C.; Mucenica, D.

    1999-01-01

    One of the most severe problems at any oil fields producing paraffinic oils is that of paraffin depositions. Romania which has a long experience in oil production is also faced with this problem in many oil fields. The microbial treatment, based on the activity of naturally occurring, selectively isolated bacteria, is already proved as an effective alternative to conventional methods to prevent and remove paraffin damage. Using such kind of bacterial products, exciting results for inhibiting paraffin depositions have been obtained. In this paper results concerning the naturally occurring bacteria selectively isolated from hydrocarbon polluted sites as well as from paraffinic oils, semi-solid and solid paraffin depositions are presented. After a laboratory screening, 15 bacterial strains (BS 1-15), three bacterial consortia (BC 1-3) and a Special Bacterial Consortium (SBC1) were selected. For the selection of bacterial consortia, the classical enrichment culture method has been used. The Special Bacterial Consortium resulted from a mixture of BS 1-15 and BC 1-3 following the steps of the classical enrichment culture method. The BS 1-15, BC 1-3 and SBC1 have been tested for their performances in producing biosurfactants and biosolvents as well as for hydrocarbon utilisation. The SBC1 has been tested for its ability in degradation of hydrocarbons contained in several types of paraffinic or non-paraffinic oils, and then for inhibiting paraffin deposition on a 'flow equipment' using two types of paraffinic oils. The SBC1 has been also tested for degradation of hydrocarbons contained in semi-solid and solid paraffin depositions. The results obtained could support further applications to prevent and control paraffin depositions

  2. Determining the color of solid paraffines in a KNS-2 colorimeter

    Energy Technology Data Exchange (ETDEWEB)

    Rozova, L P; Gladyshev, V P; Ivanov, V S; Men' kov, P A

    1980-01-01

    A new method is presented for determining the color of solid paraffines in a recently developed KNS-2 colorimeter. The essence of this particular method lies in a comparison of the intensity of the color of a melted paraffin sample with a set of standard light filters. The color of the paraffin is expressed in conditional brands. The method is simple, reliable and has good result convergence.

  3. Design and Testing of Digitally Manufactured Paraffin Acrylonitrile-Butadiene-Styrene Hybrid Rocket Motors

    OpenAIRE

    McCulley, Jonathan M.

    2013-01-01

    This research investigates the application of additive manufacturing techniques for fabricating hybrid rocket fuel grains composed of porous Acrylonitrile-butadiene-styrene impregnated with paraffin wax. The digitally manufactured ABS substrate provides mechanical support for the paraffin fuel material and serves as an additional fuel component. The embedded paraffin provides an enhanced fuel regression rate while having no detrimental effect on the thermodynamic burn properties of the fuel g...

  4. A new technique for Gram staining paraffin-embedded tissue.

    Science.gov (United States)

    Engbaek, K; Johansen, K S; Jensen, M E

    1979-01-01

    Five techniques for Gram staining bacteria in paraffin sections were compared on serial sections of pulmonary tissues from eight bacteriological necropsies. Brown and Hopp's method was the most satisfactory for distinguishing Gram-positive and Gram-negative bacteria. However, this method cannot be recommended as the preparations were frequently overstained, and the Gram-negative bacteria were stained indistinctly. A modification of Brown and Hopps' method was developed which stains larger numbers of Gram-negative bacteria and differentiates well between different cell types and connective tissue, and there is no risk of overstaining. PMID:86548

  5. Integration of catalyst design and reactor engineering in paraffins dehydrogenation

    Energy Technology Data Exchange (ETDEWEB)

    Sanfilippo, D.; Miracca, I. [Snamprogetti S.p.A., S. Donato Milanese (Italy)

    2005-07-01

    Unfortunately, olefins are not a natural fossil resource. Their production requires sophisticated and costly technologies, highly demanding in terms of investments and energy. Dehydrogenations are applied industrially to light alkanes (propane to propylene for polymers and isobutane to iso-butylene for gasoline and polymers) as well as long linear ones (C{sub 10}-C{sub 14} to linear-alkyl-benzenes) and for the production of styrene from ethylbenzene. The light paraffins dehydrogenation sustains a network of technologies allowing an integrated approach to create value from Natural Gas. (orig.)

  6. A Local Composition Model for Paraffinic Solid Solutions

    DEFF Research Database (Denmark)

    Coutinho, A.P. João; Knudsen, Kim; Andersen, Simon Ivar

    1996-01-01

    The description of the solid-phase non-ideality remains the main obstacle in modelling the solid-liquid equilibrium of hydrocarbons. A theoretical model, based on the local composition concept, is developed for the orthorhombic phase of n-alkanes and tested against experimental data for binary sy...... systems. It is shown that it can adequately predict the experimental phase behaviour of paraffinic mixtures. This work extends the applicability of local composition models to the solid phase. Copyright (C) 1996 Elsevier Science Ltd....

  7. The influence of expanded graphite on thermal properties for paraffin/high density polyethylene/chlorinated paraffin/antimony trioxide as a flame retardant phase change material

    International Nuclear Information System (INIS)

    Zhang Ping; Song Lei; Lu Hongdian; Wang Jian; Hu Yuan

    2010-01-01

    The influences of expanded graphite (EG) on the thermal properties of chlorinated paraffin (CP) and antimony trioxide (AT) on phase change material which bases on paraffin/high density polyethylene (HDPE) are studied. Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), thermogravimetric analysis-Fourier transform infrared spectrometry (TGA-FTIR), microscale combustion calorimeter (MCC) and cone calorimeter (CONE) were used to evaluate the influence of EG on paraffin/HDPE/CP/AT system. The DSC results indicated that the latent heat value of PCM could be increased when the mass fraction of HDPE was decreased in the PCM, and EG could confine the molecular heat movement of paraffin. EG could improve the thermal stability and increase the char residue at high temperature for paraffin/HDPE/CP/AT hybrid. The volatilized products formed on thermal degradation of paraffin/HDPE/CP/AT with EG showed the release of CO 2 gas was hastened and increased, and the amount of combustible gases were decreased by TGA-FTIR analysis. The MCC and CONE results presented that the flame retardant efficiency of CP/AT could be improved by adding EG in paraffin/HDPE/CP/AT system.

  8. Neutron spectrum in small iron pile surrounded by lead reflector

    International Nuclear Information System (INIS)

    Kimura, Itsuro; Hayashi, S.A.; Kobayashi, Katsuhei; Matsumura, Tetsuo; Nishihara, Hiroshi.

    1978-01-01

    In order to save the quantity of sample material, a possibility to assess group constants of a reactor material through measurement and analysis of neutron spectrum in a small sample pile surrounded by a reflector of heavy moderator, was investigated. As the sample and the reflector, we chose iron and lead, respectively. Although the time dispersion in moderation of neutrons was considerably prolonged by the lead reflector, this hardly interferes with the assessment of group constants. Theoretical calculation revealed that both the neutron flux spectrum and the sensitivity coefficient of group constants in an iron sphere, 35 cm in diameter surrounded by the lead reflector, 25 cm thick, were close to those of the bare iron sphere, 108 cm in diameter. The neutron spectra in a small iron pile surrounded by a lead reflector were experimentally obtained by the time-of-flight method with an electron linear accelerator and the result was compared with the predicted values. It could be confirmed that a small sample pile surrounded by a reflector, such as lead, was as useful as a much larger bulk pile for the assessment of group constants of a reactor material. (auth.)

  9. Method of removing paraffin from mineral oils, shale oils, tar oils, and their fractions or residues

    Energy Technology Data Exchange (ETDEWEB)

    Palmquist, F T.E.

    1949-09-08

    A method is described for removing paraffin from mineral oils, shale oils, tar oils, and their fractions or residues by centrifuging in the presence of oil-dissolving and paraffin-precipitating solvents, by which the precipitated paraffin is made to pass through an indifferent auxiliary liquid, in which a removal of oil takes place, characterized in that as auxiliary liquid is used a liquid or mixture of liquids whose surface tension against the oil solution is sufficiently low for the paraffin to pass the layer of auxiliary liquid in the form of separate crystals.

  10. Binaural Rendering in MPEG Surround

    Directory of Open Access Journals (Sweden)

    Kristofer Kjörling

    2008-04-01

    Full Text Available This paper describes novel methods for evoking a multichannel audio experience over stereo headphones. In contrast to the conventional convolution-based approach where, for example, five input channels are filtered using ten head-related transfer functions, the current approach is based on a parametric representation of the multichannel signal, along with either a parametric representation of the head-related transfer functions or a reduced set of head-related transfer functions. An audio scene with multiple virtual sound sources is represented by a mono or a stereo downmix signal of all sound source signals, accompanied by certain statistical (spatial properties. These statistical properties of the sound sources are either combined with statistical properties of head-related transfer functions to estimate “binaural parameters” that represent the perceptually relevant aspects of the auditory scene or used to create a limited set of combined head-related transfer functions that can be applied directly on the downmix signal. Subsequently, a binaural rendering stage reinstates the statistical properties of the sound sources by applying the estimated binaural parameters or the reduced set of combined head-related transfer functions directly on the downmix. If combined with parametric multichannel audio coders such as MPEG Surround, the proposed methods are advantageous over conventional methods in terms of perceived quality and computational complexity.

  11. Problems in waterflooding fields containing paraffinic crude oils

    Energy Technology Data Exchange (ETDEWEB)

    Kovalev, A G; Lyutin, L V; Perevalov, V G

    1968-11-01

    When Caspian seawater is injected into the Uzen field reservoir, the temperature of the reservoir oil can be lowered 10/sup 0/ to 20/sup 0/C below initial reservoir temperature. Because Uzen crude oil is saturated with paraffin, the cold injection water can deposit paraffin in the formation and reduce oil recovery. In a related study, it was shown that the lower temperature should not adversely affect capillary and wettability behavior of the crude oil in the reservoir. Oil recovery was found to be essentially independent of water composition. However, fresh water is easier to handle in injection systems than brines. Several studies have shown that oil recovery from Uzen field should be increased by use of hot injection water. Various methods of heating the water are discussed. To reduce corrosivity and scaling of hot brine, sodium hexametaphosphate is added in concentrations of 2 to 15 mg/liter. It is concluded that it would be practical to use hot injection water in this field.

  12. Detection of apoptotic cells in tumour paraffin sections

    International Nuclear Information System (INIS)

    Pizem, J.; Coer, A.

    2003-01-01

    Apoptosis is a distinct form of cell death characterised by specific morphological features and regulated by complex molecular mechanisms. Its deregulation is fundamental for tumour growth and progression and, moreover, anticancer therapies suppress tumour growth mainly by induction of apoptosis. Since the extent of apoptosis in a tumour may have prognostic as well as therapeutic implications, much effort has been invested in developing specific methods that can be routinely used to detect apoptotic cells in archival formalin- fixed paraffin-embedded tissue. Complex molecular pathways are involved in the regulation of apoptosis. Pro-apoptotic signals trigger activation of caspases that specifically cleave target proteins. Cleavage of proteins (caspase substrates) is responsible for morphological changes of apoptotic cells and DNA fragmentation. In the last decade, detection of apoptotic cells in formalin-fixed tumour tissue sections has been based mainly on morphology and characteristic DNA fragmentation. Recently, specific antibodies to activated caspases and cleaved target proteins (including cytokeratin 18, actin and PARP) have been produced that enable accurate detection of apoptosis in paraffin sections. (author)

  13. Detection of p62 on Paraffin Sections by Immunohistochemistry.

    Science.gov (United States)

    Watson, Alexander S; Soilleux, Elizabeth J

    2015-08-03

    The study of autophagy in human disease is a rapidly expanding field. Diagnostic paraffin sections of a variety of patient tissues, including bone marrow, are available to researchers-yet are unsuitable for traditional autophagy quantification methods such as western blot or electron microscopy. This protocol outlines the immunohistochemical detection of the protein p62 (sequestosome-1, encoded by the gene SQSTM1)-an indicator of autophagic degradative activity-in slide-mounted paraffin sections such as bone marrow samples cut by a trephine. The p62 protein is an autophagic cargo adaptor, capable of binding to ubiquitylated proteins as well as autophagosome membrane proteins (LC3B and GABA(A) receptor-associated protein [GABARAP] family members) and hypothesized thus to target protein aggregates for lysosomal degradation. p62 itself is degraded by autophagy, remaining at low levels when autophagy is induced, and has been shown to accumulate when autophagy is deficient. Qualitative assessment and comparison of p62 staining between healthy and disease sections or disease subtypes will help target further investigation into the potential roles for autophagy in a variety of disorders. © 2015 Cold Spring Harbor Laboratory Press.

  14. Paraffin molecule mobility in channel clathrates of urea on spectroscopic NMR relaxation data

    CERN Document Server

    Kriger, Y G; Chekhova, G N

    2001-01-01

    The temperature dependences of the protons spin-lattice relaxation time (T sub I) in the channel clathrates of urea with paraffins are measured. The data on the T sub I are interpreted within the frames of the model of the paraffins molecules and their fragments orientation in the clathrate channels. The dynamics peculiarities are connected with the disproportion effects of these compounds

  15. Enhanced thermal properties with graphene oxide in the urea-formaldehyde microcapsules containing paraffin PCMs.

    Science.gov (United States)

    Qiao, Zhen; Mao, Jian

    2017-02-01

    In this study, compact urea-formaldehyde microcapsules containing paraffin (UFP) phase change materials (PCMs) were prepared via in situ polymerisation. The thermal conductivity of the PCMs was enhanced without influencing their enthalpy by adding graphene oxide (GO). Two modification methods were investigated: One in which GO is added to the inside of microcapsules, defined as "paraffin/GO@UF composite"; and another in which GO is coated onto the surface of shell, defined as "paraffin@UF/GO composite". The GO sheets were visible in scanning electron microscope (SEM) images of paraffin@UF/GO composite. The thermal conductivity was 0.2236 ± 0.0003 W/(m·K) for UFP particles, was 0.2517 ± 0.0003 W/(m·K) for the paraffin/GO@UF composite (10 wt%), and was 1.0670 ± 0.0020 W/(m·K) for paraffin@UF/GO composite (10 wt%), respectively. The encapsulation efficiency of all samples exceeded 80% (w/w) and all samples exhibited favourable thermal stability and reliability. The IR emissivity of paraffin@UF/GO was lower than that of paraffin/GO@UF when the same GO amount was added to the composite.

  16. High paraffin Kumkol petroleum processing under fuel and lubricant petroleum scheme

    International Nuclear Information System (INIS)

    Nadirov, N.K.; Konaev, Eh.N.

    1997-01-01

    Technological opportunity of high paraffin Kumkol petroleum processing under the fuel and lubricant scheme with production of lubricant materials in short supply, combustible materials and technical paraffin is shown. Mini petroleum block putting into operation on Kumkol deposit is reasonable economically and raises profitableness of hydrocarbon raw material production. (author)

  17. Sealing-free fast-response paraffin/nanoporous gold hybrid actuator

    Science.gov (United States)

    Ye, Xing-Long; Jin, Hai-Jun

    2017-09-01

    Paraffin-based actuators can deliver large actuation strokes and high actuation stress, but often suffer from a low response rate and leaking problems. Here, we report a new paraffin/metal hybrid actuator, which was fabricated by infiltrating nanoporous gold with paraffin. It exhibits a fast actuation rate owing to the high thermal conductivity of the inter-connected metal phase, and requires no external sealing because liquid paraffin can be well confined in nanoscale channels, due to the large capillarity. We found that in this hybrid actuator, the stress generated by actuation is negligibly small when the characteristic size of the nanoporous gold (L) is above ˜70 nm, and increases dramatically with a decreasing size when L paraffin wax—the paraffin in smaller pores can sustain larger tensile stress, and thus the contraction of paraffin during cooling can be translated into larger compression stress and strain energy in a metal framework, leading to a larger actuation stress and energy. We also demonstrate that complex actuation motions can be achieved by incorporating hierarchical-structured nanoporous metal with paraffin.

  18. Corrugated paraffin nanocomposite films as large stroke thermal actuators and self-activating thermal interfaces.

    Science.gov (United States)

    Copic, Davor; Hart, A John

    2015-04-22

    High performance active materials are of rapidly growing interest for applications including soft robotics, microfluidic systems, and morphing composites. In particular, paraffin wax has been used to actuate miniature pumps, solenoid valves, and composite fibers, yet its deployment is typically limited by the need for external volume constraint. We demonstrate that compact, high-performance paraffin actuators can be made by confining paraffin within vertically aligned carbon nanotube (CNT) films. This large-stroke vertical actuation is enabled by strong capillary interaction between paraffin and CNTs and by engineering the CNT morphology by mechanical compression before capillary-driven infiltration of the molten paraffin. The maximum actuation strain of the corrugated CNT-paraffin films (∼0.02-0.2) is comparable to natural muscle, yet the maximum stress is limited to ∼10 kPa by collapse of the CNT network. We also show how a CNT-paraffin film can serve as a self-activating thermal interface that closes a gap when it is heated. These new CNT-paraffin film actuators could be produced by large-area CNT growth, infiltration, and lamination methods, and are attractive for use in miniature systems due to their self-contained design.

  19. Medium-chain chlorinated paraffins (MCCPs): a review of bioaccumulation potential in the aquatic environment.

    Science.gov (United States)

    Thompson, Roy; Vaughan, Martin

    2014-01-01

    Chlorinated paraffins (CPs) are high molecular weight organochlorine compounds that have been used in a variety of industrial applications for many years. Medium-chain chlorinated paraffins (MCCPs) (CAS 85535-85-9; Alkanes, C14-17 , chloro) are currently under investigation as potential persistent bioaccumulative toxic (PBT) compounds. In this article, the bioaccumulation potential of MCCPs is assessed using a tiered framework proposed after a recent Society of Environmental Toxicology and Chemistry (SETAC) Pellston Workshop in 2008. The framework proposes the use of physicochemical properties and modeling assessment, bioconcentration/bioaccumulation (BCF/BAF) assessment, biomagnification (BMF) assessment, and trophic magnification factor (TMF) assessment. It is hoped that use of this framework could harmonize and improve the efficiency and effectiveness of the chemical substance evaluation screening process for PBT properties. When applied to MCCPs, the following conclusions were made: empirical physiochemical data is available negating the use of models; laboratory BCFs range from 1000 to 15 000 (growth-corrected lipid normalized values) for 2 MCCP structures; field BAFs were an order of magnitude higher than the trigger criterion for "B status possible"; although results may not meet acceptance criteria for field studies, laboratory-derived BMFs for a number of C14-17 chlorinated alkanes were less than the trigger value of 1 (based on whole-body concentrations) whereas field-derived BMFs were less than 1 (based on lipid corrected values [generally used for field data] excluding one measure for sculpin, [Cottus cognatus]-Diporeia that was based on only one detectable sample); and finally, TMFs were less than the trigger criterion value of 1, which are considered the most convincing evidence for bioaccumulative properties of a compound and the "Gold Standard" measure of bioaccumulation. This article also discusses the uncertainties surrounding the published data

  20. Tracking Dietary Sources of Short- and Medium-Chain Chlorinated Paraffins in Marine Mammals through a Subtropical Marine Food Web.

    Science.gov (United States)

    Zeng, Lixi; Lam, James C W; Chen, Hui; Du, Bibai; Leung, Kenneth M Y; Lam, Paul K S

    2017-09-05

    Our previous study revealed an elevated accumulation of short-chain chlorinated paraffins (SCCPs) and medium-chain chlorinated paraffins (MCCPs) in marine mammals from Hong Kong waters in the South China Sea. To examine the bioaccumulation potential and biomagnification in these apex predators, we sampled the dietary items of marine mammals and tracked the sources of SCCPs and MCCPs through a marine food web in this region. Sixteen fish species, seven crustacean species, and four mollusk species were collected, and the main prey species were identified for two species of marine mammals. Concentrations of ∑SCCPs and ∑MCCPs in these collected species suggested a moderate pollution level in Hong Kong waters compared to the global range. Lipid content was found to mediate congener-specific bioaccumulation in these marine species. Significantly positive correlations were observed between trophic levels and concentrations of ∑SCCPs or ∑MCCPs (p mammals was observed. This is the first report of dietary source tracking of SCCPs and MCCPs in marine mammals. The elevated biomagnification between prey and marine mammals raises environmental concerns about these contaminants.

  1. Experimental study on heat capacity of paraffin/water phase change emulsion

    International Nuclear Information System (INIS)

    Huang, L.; Noeres, P.; Petermann, M.; Doetsch, C.

    2010-01-01

    A paraffin/water phase change emulsion is a multifunctional fluid in which fine paraffin droplets are dispersed in water by a surfactant. This paper presents an experimental study on the heat capacity of an emulsion containing 30 wt.% paraffin in a test rig. The results show that the heat capacity of the emulsion consists of the sensible heat capacity of water and that of the paraffin as well as the latent heat capacity of the paraffin during the phase transition solid-liquid. The emulsion is an attractive alternative to chilled water for comfort cooling applications, because it has a heat capacity of 50 kJ/kg from 5 to 11 deg. C, which is two times as high as that of water in the same temperature range.

  2. Carbon nanotube/paraffin/montmorillonite composite phase change material for thermal energy storage.

    Science.gov (United States)

    Li, Min; Guo, Qiangang; Nutt, Steven

    2017-04-01

    A composite phase change material (PCM) comprised of organic montmorillonite (OMMT)/paraffin/grafted multi-walled nanotube (MWNT) is synthesized via ultrasonic dispersion and liquid intercalation. The microstructure of the composite PCM has been characterized to determine the phase distribution, and thermal properties (latent heat and thermal conductivity) have been measured by differential scanning calorimetry (DSC) and a thermal constant analyzer. The results show that paraffin molecules are intercalated in the montmorillonite layers and the grafted MWNTs are dispersed in the montmorillonite layers. The latent heat is 47.1 J/g, and the thermal conductivity of the OMMT/paraffin/grafted MWNT composites is 34% higher than that of the OMMT/paraffin composites and 65% higher than that of paraffin.

  3. Exogenous lipoid pneumonia caused by paraffin in an amateur fire breather.

    Science.gov (United States)

    Weinberg, I; Fridlender, Z G

    2010-05-01

    Paraffin has characteristics that make it popular among fire breathers. To describe a case of paraffin-induced lipoid pneumonia in a fire breather. The patient was evaluated clinically in relation to his occupational history. A 32-year-old man presented with dyspnoea, tachypnoea and non-productive cough of 2 h duration that started immediately following an attempt to blow fire using paraffin as the volatile substance. He was discharged from the emergency ward but returned the next day presenting again with dyspnoea accompanied by mid-sternal pain, fever (38.1 degrees C) and leucocytosis. Chest radiography showed perihilar punctuate infiltrations. A diagnosis of exogenous lipoid pneumonia caused by paraffin was made, and the patient was treated, with full recovery within a week. Fire breathers must be viewed as a population at risk of paraffin-induced lipoid pneumonia.

  4. Paraffin as oxygen vector modulates tyrosine phenol lyase production by Citrobacter freundii MTCC 2424.

    Science.gov (United States)

    Azmi, Wamik; Kumar, Ajay; Dev, Varun

    2013-06-01

    The efficiency of three oxygen-vectors liquid paraffin, silicone oil and n-dodecane in the production of tyrosine phenol lyase (TPL) by Citrobacter freundii MTCC 2424 was evaluated at 4% (v/v) concentration. The liquid paraffin as oxygenvectors was found to exhibit a stimulatory effect on TPL synthesis. The liquid paraffin at 6% (v/v) resulted in 34% increase in the TPL synthesis accompanied by a 13% increase in the production of cell mass at a 10 L scale. This improvement in TPL and cell mass production in the presence of liquid paraffin can be related to the fact that liquid paraffin was capable of maintaining dissolved O2 concentration above 28% throughout the course of the fermentation. Maintenance of the dissolved O2 concentration above 28% could be viewed in terms of an adequate oxygen supply to the rapidly dividing cells of the bacterium, which in turn resulted in enhanced synthesis of TPL and cell mass.

  5. Ionic liquids for separation of olefin-paraffin mixtures

    Science.gov (United States)

    Dai, Sheng; Luo, Huimin; Huang, Jing-Fang

    2013-09-17

    The invention is directed to an ionic liquid comprising (i) a cationic portion containing a complex of a silver (I) ion and one or more neutral ligands selected from organoamides, organoamines, olefins, and organonitriles, and (ii) an anionic portion having the chemical formula ##STR00001## wherein m and n are independently 0 or an integer of 1 or above, and p is 0 or 1, provided that when p is 0, the group --N--SO.sub.2--(CF.sub.2).sub.nCF.sub.3 subtended by p is replaced with an oxide atom connected to the shown sulfur atom. The invention is also directed to a method for separating an olefin from an olefin-paraffin mixture by passing the mixture through a layer of the ionic liquid described above.

  6. Round-Robin Test of Paraffin Phase-Change Material

    Science.gov (United States)

    Vidi, S.; Mehling, H.; Hemberger, F.; Haussmann, Th.; Laube, A.

    2015-11-01

    A round-robin test between three institutes was performed on a paraffin phase-change material (PCM) in the context of the German quality association for phase-change materials. The aim of the quality association is to define quality and test specifications for PCMs and to award certificates for successfully tested materials. To ensure the reproducibility and comparability of the measurements performed at different institutes using different measuring methods, a round-robin test was performed. The sample was unknown. The four methods used by the three participating institutes in the round-robin test were differential scanning calorimetry, Calvet calorimetry and three-layer calorimetry. Additionally, T-history measurements were made. The aim of the measurements was the determination of the enthalpy as a function of temperature. The results achieved following defined test specifications are in excellent agreement.

  7. Standard Review Risk Assessment on Medium-chain and Long-chain Chlorinated paraffin PMN submissions by INEOS Chlor Americas

    Science.gov (United States)

    This assessment was conducted under EPA’s TSCA Section 5 New Chemicals Program. EPA is assessing Medium-chain Chlorinated Paraffin (MCCP) and Long-Chain Chlorinated Paraffin (LCCP) chemicals as part of its New Chemicals Review program.

  8. Standard Review Risk Assessment on Medium-chain and Long-chain Chlorinated paraffin PMN submissions by Dover Chemical

    Science.gov (United States)

    This assessment was conducted under EPA’s TSCA Section 5 New Chemicals Program. EPA is assessing Medium-chain Chlorinated Paraffin (MCCP) and Long-Chain Chlorinated Paraffin (LCCP) chemicals as part of its New Chemicals Review program.

  9. Standard Review Risk Assessment on Medium-chain and Long-chain Chlorinated paraffin PMN submissions by Qualice, LLC

    Science.gov (United States)

    This assessment was conducted under EPA’s TSCA Section 5 New Chemicals Program. EPA is assessing Medium-chain Chlorinated Paraffin (MCCP) and Long-Chain Chlorinated Paraffin (LCCP) chemicals as part of its New Chemicals Review program.

  10. Controlled release of insect sex pheromones from paraffin wax and emulsions.

    Science.gov (United States)

    Atterholt, C A; Delwiche, M J; Rice, R E; Krochta, J M

    1999-02-22

    Paraffin wax and aqueous paraffin emulsions can be used as controlled release carriers for insect sex pheromones for mating disruption of orchard pests. Paraffin can be applied at ambient temperature as an aqueous emulsion, adheres to tree bark or foliage, releases pheromone for an extended period of time, and will slowly erode from bark and biodegrade in soil. Pheromone emulsions can be applied with simple spray equipment. Pheromone release-rates from paraffin were measured in laboratory flow-cell experiments. Pheromone was trapped from an air stream with an adsorbent, eluted periodically, and quantified by gas chromatography. Pheromone release from paraffin was partition-controlled, providing a constant (zero-order) release rate. A typical paraffin emulsion consisted of 30% paraffin, 4% pheromone, 4% soy oil, 1% vitamin E, 2% emulsifier, and the balance water. Soy oil and vitamin E acted as volatility suppressants. A constant release of oriental fruit moth pheromone from paraffin emulsions was observed in the laboratory for more than 100 days at 27 degreesC, with release-rates ranging from 0.4 to 2 mg/day, depending on the concentration and surface area of the dried emulsion. The use of paraffin emulsions is a viable method for direct application of insect pheromones for mating disruption. Sprayable formulations can be designed to release insect pheromones to the environment at a rate necessary for insect control by mating disruption. At temperatures below 38 degreesC, zero-order release was observed. At 38 degreesC and higher, pheromone oxidation occurred. A partition-controlled release mechanism was supported by a zero-order pheromone release-rate, low air/wax partition coefficients, and pheromone solubility in paraffin.

  11. Reflector-moderated critical assemblies

    International Nuclear Information System (INIS)

    Paxton, H.C.; Jarvis, G.A.; Byers, C.C.

    1975-07-01

    Experiments with reflector-moderated critical assemblies were part of the Rover Program at the Los Alamos Scientific Laboratory (LASL). These assemblies were characterized by thick D 2 O or beryllium reflectors surrounding large cavities that contained highly enriched uranium at low average densities. Because interest in this type of system has been revived by LASL Plasma Cavity Assembly studies, more detailed descriptions of the early assemblies than had been available in the unclassified literature are provided. (U.S.)

  12. Interaction study of polyisobutylene with paraffins by NMR using the evaluation of spin-lattice relaxation times for hydrogen nuclei

    International Nuclear Information System (INIS)

    Marques, Rosana G.G.; Tavares, Maria I.B.

    2001-01-01

    The evaluation of spin-lattice relaxation times of 1 H for polyisobutylene/paraffin systems, were obtained using the classic inversion recovery technique, and also through Cross Polarization Magic Angle Spinning (CP/MAS) techniques varying the contact time and also by the delayed contact time pulse sequence. NMR results showed that the polyisobutylene/paraffin systems in which high molecular weight paraffins were used, is heterogeneous. However, for paraffins with low molecular weight, the system presents good homogeneity. (author)

  13. Retrofit with membrane the Paraffin/Olefin separation

    Energy Technology Data Exchange (ETDEWEB)

    Motelica, A.; Bruinsma, O.S.L.; Kreiter, R.; Den Exter, M.J.; Vente, J.F. [ECN Biomass and Energy Efficiency, Petten (Netherlands)

    2012-10-15

    Olefins, such as ethylene, propylene, and butadiene, are among the most produced intermediates in petrochemical industry. They are produced from a wide range of hydrocarbon feedstocks (ethane, propane, butane, naphtha, gas oil) via a cracking process. The last step in this process is the separation of olefins from other hydrocarbons, which is traditionally performed with distillation. As the physicochemical properties, such as volatility and boiling point, of the compounds are very similar, the purification becomes capital and energy intensive. For example, the top of an ethylene/ethane distillation column needs to be chilled to -30C and this requires large amount of electric energy consumption. The separation of butadiene from the C4-fraction is performed with the aid of an additional solvent. This solvent has to be regenerated at the cost of additional high temperature steam. To overcome these separation disadvantages of olefin/paraffin separation, different separation methods have been investigated and proposed in recent years. Suggested options are based on better heat integration of the overall process, or on novel separation systems such as Heat Integrated Distillation Columns, membrane separation, adsorption-desorption systems or on hybrid separation methods, for example, distillation combined with membrane separation.

  14. Chlorinated paraffins wrapping of carbon nanotubes: A theoretical investigation

    Science.gov (United States)

    Ding, Qiuyue; Ding, Ning; Chen, Xiangfeng; Wu, Chi-Man Lawrence

    2018-04-01

    How nanomaterials interact with pollutants is the central for understanding their environmental behavior and practical application. In this work, molecular dynamics (MD) and density functional theoretical (DFT) methods were used to investigated the influence of carbon chain length, degree of chlorination, chain configuration, and chirality of chlorinated paraffin (CP) and diameter of single-walled carbon nanotubes (SWNTs) on the interaction between CPs and SWNTs. The simulation results demonstrated that CP chain length and chlorination degree played considerably important roles in determining interaction strength between SWNTs and CPs. The interaction energies increased with increasing chain length and chlorination degree. The chirality of SWNT exerted negligible influence on the interaction energy between SWNTs and CPs. On the contrary, interaction energy increased with increasing radius of SWNTs due to the surface curvatures. This result was rationalized by considering the decrease in SWNT curvature with increasing radius, which resulted in plane-like CNT wall. The negligible influence of CP chain configurations was attributed to relative flexibility of CP carbon chains, which can wrap on tubes through conformational changes with low-energy barriers. MD results indicated that CPs could adsorb on SWNT surface rapidly in aqueous environment. Charge transfer and electronic density results indicated that the interaction between CPs and SWNTs was physisorption in nature. This work provides fundamental information regarding SWNTs as sorbents for CPs extraction and adsorptive removal from environmental water system.

  15. Quantifying Short-Chain Chlorinated Paraffin Congener Groups.

    Science.gov (United States)

    Yuan, Bo; Bogdal, Christian; Berger, Urs; MacLeod, Matthew; Gebbink, Wouter A; Alsberg, Tomas; de Wit, Cynthia A

    2017-09-19

    Accurate quantification of short-chain chlorinated paraffins (SCCPs) poses an exceptional challenge to analytical chemists. SCCPs are complex mixtures of chlorinated alkanes with variable chain length and chlorination level; congeners with a fixed chain length (n) and number of chlorines (m) are referred to as a "congener group" C n Cl m . Recently, we resolved individual C n Cl m by mathematically deconvolving soft ionization high-resolution mass spectra of SCCP mixtures. Here we extend the method to quantifying C n Cl m by introducing C n Cl m specific response factors (RFs) that are calculated from 17 SCCP chain-length standards with a single carbon chain length and variable chlorination level. The signal pattern of each standard is measured on APCI-QTOF-MS. RFs of each C n Cl m are obtained by pairwise optimization of the normal distribution's fit to the signal patterns of the 17 chain-length standards. The method was verified by quantifying SCCP technical mixtures and spiked environmental samples with accuracies of 82-123% and 76-109%, respectively. The absolute differences between calculated and manufacturer-reported chlorination degrees were -0.9 to 1.0%Cl for SCCP mixtures of 49-71%Cl. The quantification method has been replicated with ECNI magnetic sector MS and ECNI-Q-Orbitrap-MS. C n Cl m concentrations determined with the three instruments were highly correlated (R 2 > 0.90) with each other.

  16. On the effect of a moderator in the central region of a hollow fuel element

    International Nuclear Information System (INIS)

    Simopoulos, S.; Leonidou, D.

    1980-01-01

    An experimental investigation of the effect of a short slowing down length moderator, in the central region of a hollow fuel element, is attempted in the present work. Water, paraffin and plexiglass have been used as moderator materials. The results obtained show that an increase of the flux level is observed with such a moderator positioned in the central region of the fuel element, when comparing the situation with that existing without a central moderator. The increase is found to depend at least upon the thermal to fast neutron composition of the neutron spectrum. (author)

  17. STR typing of formalin-fixed paraffin embedded (FFPE) aborted foetal tissue in criminal paternity cases.

    Science.gov (United States)

    Reshef, Ayeleth; Barash, Mark; Voskoboinik, Lev; Brauner, Paul; Gafny, Roni

    2011-03-01

    Sexual assault or rape cases occasionally result in unwanted pregnancies. In almost all such cases the foetus is aborted. A forensic laboratory may receive the foetus, the placenta, or paraffin embedded abortion material for paternity testing. Obtaining a foetal profile DNA from a foetus or placenta may not be successful due to the age or condition of the tissue. Moreover, maternal contamination of placental material will invariably result in a mixed DNA profile. However, the use of properly screened abortion material from paraffin blocks will almost always result in obtaining a foetal DNA profile. Furthermore, foetal tissue fixed in paraffin blocks does not require special conditions for submission and storage as required to preserve fresh foetal or placental tissue. As hospitals routinely prepare foetal tissue in paraffin blocks, which should be readily obtainable by forensic laboratories, these samples would appear to be the preferred choice for paternity testing. 2010 Forensic Science Society. Published by Elsevier Ireland Ltd. All rights reserved.

  18. Preparation and Properties of Paraffin/TiO2/Active-carbon Composite Phase Change Materials

    Directory of Open Access Journals (Sweden)

    HAO Yong-gan

    2016-11-01

    Full Text Available A novel composite phase change materials (PCMs of paraffin/TiO2/active-carbon was prepared by a microemulsion method, where paraffin acted as a PCM and titanium dioxide (TiO2 as matrix material, and a small amount of active carbon was added to improve the thermal conductivity. The compositions, morphology and thermal properties of the paraffin/TiO2/active-carbon composite PCMs were characterized by XRD, SEM, TGA and DSC respectively. The shape stability during phase change process of this composite was also tested. The results show that paraffin is well encapsulated by TiO2 matrix, and thus exhibiting excellent shape-stabilized phase change feature. Besides, this composite PCM also presents superhydrophobic property. Therefore, these multifunctional features will endow PCMs with important application potential in energy efficient buildings.

  19. Recent developments in capabilities for analysing chlorinated paraffins in environmental matrices: A review

    NARCIS (Netherlands)

    van Mourik, L.M.; Leonards, P.E.G.; Gaus, C.; de Boer, J.

    2015-01-01

    Concerns about the high production volumes, persistency, bioaccumulation potential and toxicity of chlorinated paraffin (CP) mixtures, especially short-chain CPs (SCCPs), are rising. However, information on their levels and fate in the environment is still insufficient, impeding international

  20. Quantum-chemical study of hydride transfer in catalytic transformation of paraffins on zeolites

    NARCIS (Netherlands)

    Kazansky, V.B.; Frash, M.V.; Santen, van R.A.; Chon, H.; Ihm, S.-K.; Uh, Y.S.

    1997-01-01

    Ab initio quantum-chemical cluster calculations demonstrate that the activated complexes of hydride transfer reaction in catalytic transformation of paraffins on zeolites very much resembles adsorbed nonclassical carbonium ions. The calculated activation energies for reactions involving propane and

  1. Effect of paraffin saturation in a crude oil on operation of a field

    Energy Technology Data Exchange (ETDEWEB)

    Trebin, G F; Kapyrin, Yu V

    1968-11-01

    Both theoretical and practical studies in recent years have shown that in planning operational procedures for an oil field, the paraffin saturation of the crude oil must be considered. If the crude oil is essentially saturated with paraffin at reservoir condition, then paraffin deposition can occur around the well and in the well. Temperature in the reservoir can be lowered by 2 mechanisms: (1) by injection of water below reservoir temperature, and (2) by expansion of produced gas and consequent cooling of the produced oil. Possible application of these principles to several Soviet oil fields is discussed. In the Uzen field, a preliminary investigation is under way to test the feasibility of heating the injection water to prevent paraffin deposition in the reservoir.

  2. Flow restrictor silicon membrane microvalve actuated by optically controlled paraffin phase transition

    International Nuclear Information System (INIS)

    Kolari, K; Havia, T; Stuns, I; Hjort, K

    2014-01-01

    Restrictor valves allow proportional control of fluid flow but are rarely integrated in microfluidic systems. In this study, an optically actuated silicon membrane restrictor microvalve is demonstrated. Its actuation is based on the phase transition of paraffin, using a paraffin wax mixed with a suitable concentration of optically absorbing nanographite particles. Backing up the membrane with oil (the melted paraffin) allows for a compliant yet strong contact to the valve seat, which enables handling of high pressures. At flow rates up to 30 µL min −1 and at a pressure of 2 bars, the valve can successfully be closed and control the flow level by restriction. The use of this paraffin composite as an adhesive layer sandwiched between the silicon valve and glass eases fabrication. This type of restrictor valve is best suited for high pressure, low volume flow silicon-based nanofluidic systems. (paper)

  3. Impact of 50% Synthesized Iso-Paraffins (SIP) on F-76 Fuel Coalescence

    Science.gov (United States)

    2013-12-16

    petroleum JP-5 and Synthesized Iso-Paraffins (SIP). SIP fuels are made from direct fermentation of sugar into olefinic hydrocarbons. The olefinic...manufactured scaled down filter/coalescer and separator to simulate the performance of a full-scale filter separator system. This test is designed to predict...5 and Synthesized Iso-Paraffins (SIP). SIP fuels are made from direct fermentation of sugar into olefinic hydrocarbons. The olefinic hydrocarbons

  4. Impact of 50% Synthesized Iso-Paraffins (SIP) on Middle Distillate Fuel Filtration and Coalescence

    Science.gov (United States)

    2014-10-30

    Paraffins DEFINITIONS Coalescence - the ability to shed water Conventional Material Source - crude oil , natural gas liquid condensates...Impact of 50% Synthesized Iso-Paraffins (SIP) on Middle Distillate Fuel Filtration and Coalescence NF&LCFT REPORT 441/15-003 30 October 2014...heavy oil , shale oil , and oil sands Effluent - stream leaving a system Influent - stream entering a system Turnover - time required to flow the

  5. Experimental preliminary exploration on determining grease thickness simulated by paraffin in petroleum pipelines

    International Nuclear Information System (INIS)

    Zhao Nongxiao; Arkin, Abulim; Yang Kunjie; Wang Shiheng; Shi Feiyue

    2009-01-01

    1.25 MeV γ-ray of 60 Co Compton scattering coefficient in the simple of paraffin,are measured by γ-ray energy spectrum analysis in two determining means. At the same experimental condition, we have used this scattering coefficient to determining grease thickness simulated by paraffin. The result show the average relative difference is about 1.29% for the best group. (authors)

  6. Paraffin Granuloma Associated with Buried Glans Penis-Induced Sexual and Voiding Dysfunction

    OpenAIRE

    Chon, Wonhee; Koo, Ja Yun; Park, Min Jung; Choi, Kyung-Un; Park, Hyun Jun; Park, Nam Cheol

    2017-01-01

    A paraffinoma is a type of inflammatory lipogranuloma that develops after the injection of an artificial mineral oil, such as paraffin or silicon, into the foreskin or the subcutaneous tissue of the penis for the purpose of penis enlargement, cosmetics, or prosthesis. The authors experienced a case of macro-paraffinoma associated with sexual dysfunction, voiding dysfunction, and pain caused by a buried glans penis after a paraffin injection for penis enlargement that had been perform...

  7. Religion's relationship with social boundaries surrounding gender ...

    African Journals Online (AJOL)

    Religion's relationship with social boundaries surrounding gender. ... is associated with segregation, marginalization and differentiation between men and women. ... are necessary in the society it should not be mistaken for gender inequality.

  8. The use of paraffin wax in a new solar cooker with inner and outer reflectors

    Directory of Open Access Journals (Sweden)

    Arabacigil Bihter

    2015-01-01

    Full Text Available In this paper, the potential use and effectiveness of paraffin wax in a new solar cooker was experimentally investigated during daylight and late evening hours. For these experiments, a cooker having an inner reflecting surface was designed, constructed by filling paraffin wax and metal shavings. The side- and sub-surface temperatures of the paraffin wax in the cooker are measured in the summer months of June and July. The thermal efficiency of the cooker was tested on different conditions. The results show that the optimum angle of the outer reflector is 30°. Here, the peak temperature of the paraffin wax in the solar cooker was 83.4 °C. The average solar radiation reflected makes a contribution of 9.26% to the temperature of paraffin wax with the outer reflector. The solar cooker with the outer reflector angle of 30° receives also reflected radiation from the inner reflectors. Besides, the heating time is decreased to approximately 1 hour. The designed solar cooker can be effectively used with 30.3% daily thermal efficiency and paraffin wax due to the amount of energy stored.

  9. Enhanced Thermo-Optical Switching of Paraffin-Wax Composite Spots under Laser Heating.

    Science.gov (United States)

    Said, Asmaa; Salah, Abeer; Fattah, Gamal Abdel

    2017-05-12

    Thermo-optical switches are of particular significance in communications networks where increasingly high switching speeds are required. Phase change materials (PCMs), in particular those based on paraffin wax, provide wealth of exciting applications with unusual thermally-induced switching properties, only limited by paraffin's rather low thermal conductivity. In this paper, the use of different carbon fillers as thermal conductivity enhancers for paraffin has been investigated, and a novel structure based on spot of paraffin wax as a thermo-optic switch is presented. Thermo-optical switching parameters are enhanced with the addition of graphite and graphene, due to the extreme thermal conductivity of the carbon fillers. Differential Scanning Calorimetry (DSC) and Scanning electron microscope (SEM) are performed on paraffin wax composites, and specific heat capacities are calculated based on DSC measurements. Thermo-optical switching based on transmission is measured as a function of the host concentration under conventional electric heating and laser heating of paraffin-carbon fillers composites. Further enhancements in thermo-optical switching parameters are studied under Nd:YAG laser heating. This novel structure can be used in future networks with huge bandwidth requirements and electric noise free remote aerial laser switching applications.

  10. Thermal conductivity enhancement of paraffin by adding boron nitride nanostructures: A molecular dynamics study

    International Nuclear Information System (INIS)

    Lin, Changpeng; Rao, Zhonghao

    2017-01-01

    Highlights: • Different contributions to thermal conductivity are obtained. • Thermal conductivity of paraffin could be improved by boron nitride. • Crystallization effect from boron nitride was the key factor. • Paraffin nanocomposite is the desirable candidate for thermal energy storage. - Abstract: While paraffin is widely used in thermal energy storage today, its low thermal conductivity has become a bottleneck for the further applications. Here, we construct two kinds of paraffin-based phase change material nanocomposites through introducing boron nitride (BN) nanostructures into n-eicosane to enhance the thermal conductivity. Molecular dynamics (MD) simulation was adopted to estimate their thermal conductivities and related thermal properties. The results indicate that, after adding BN nanostructures, the latent heat of composites is reduced compared with the pure paraffin and they both show a glass-like thermal conductivity which increases as the temperature rises. This happens because the increasing temperature leads to gradually smaller inconsistency in vibrational density of state along three directions and increasingly significant overlaps among them. Furthermore, by decomposing the thermal conductivity, it is found that the major contribution to the overall thermal conductivity comes from BN nanostructures, while the contribution of n-eicosane is insignificant. Though the thermal conductivity from n-eicosane term is small, it has been improved greatly compared with amorphous state of n-eicosane, mainly due to the crystallization effects from BN nanostructures. This work will provide microscopic views and insights into the thermal mechanism of paraffin and offer effective guidances to enhance the thermal conductivity.

  11. Electrically conductive carbon nanofiber/paraffin wax composites for electric thermal storage

    International Nuclear Information System (INIS)

    Zhang Kun; Han Baoguo; Yu Xun

    2012-01-01

    Highlights: ► Carbon nanofiber (CNF)/paraffin wax composite is found to be a promising electric thermal storage material. ► The thermal storage capacity of CNF/paraffin wax composite is five times of traditional electric thermal storage material. ► CNF is shown to be an effective conductive filler for the composite. - Abstract: The research of electric thermal storage (ETS) has attracted a lot of attention recently, which converts off-peak electrical energy into thermal energy and release it later at peak hours. In this study, new electric thermal storage composites are developed by employing paraffin wax as thermal storage media and carbon nanofiber (CNF) as conductive fillers. Electric heating and thermal energy release performances of the CNF/paraffin wax composites are experimentally investigated. Experimental results show that, when the composites are heated to about 70 °C, the developed electrically conductive CNF/paraffin wax composites present a thermal storage capacity of about 280 kJ/kg, which is five times of that of traditional thermal storage medium such as ceramic bricks (54 kJ/kg). The CNF/paraffin wax composites can also effectively store the thermal energy and release the thermal energy in later hours.

  12. Chemical changes in the chloroform-paraffin system irradiated by 60Co gamma-rays, 1

    International Nuclear Information System (INIS)

    Yoshino, Tomio; Sakaue, Muneko; Shimizu, Yasuko; Kawamura, Fumio.

    1979-01-01

    It has been reported that the chloroform-paraffin-dye system have excellent sensitivity for radiation as a solid chemical dosimeter or a phantom. However, the chemical changes in the irradiated system are not examined in detail. In the present study, the effect of paraffin on changes in the above system of a liquid state irradiated by 60 Co γ-rays was examined by using various normal paraffin, and the other variable factors on the changes were done. When the chloroform solution and the solution containing 25 per cent of paraffin by volume with 5.0 x 15 -5 mol/liter of Methyl Yellow as a dye were irradiated by 2000 R, G values for the formation of hydrogen chloride in the both solutions were 8.4 and 10.8, respectively, and were little affected by the kind of those, from C 6 (hexane) to C 36 (hexatria-contane). These results suggest that chlorine radical formed by radiolysis of chloroform may react with hydrogen atom from paraffin, thereby increasing the amount of hydrogen chloride. Presence of oxygen increased G value of the chloroform solution from 7.6 to 8.4, but did little that of the solution containing paraffin. (author)

  13. Investigation of rare chronic lipoid pneumonia associated with occupational exposure to paraffin aerosol.

    Science.gov (United States)

    Han, Chenghong; Liu, Lihai; Du, Shiping; Mei, Jianhua; Huang, Ling; Chen, Min; Lei, Yongliang; Qian, Junwen; Luo, Jianyong; Zhang, Meibian

    2016-09-30

    Occupational exposure to paraffin is an infrequent cause of lipoid pneumonia (LP) and related data are scare. We investigated the possible relationship between three rare cases of chronic LP and occupational exposure to paraffin aerosol in an iron foundry. The three cases of LP and their workplaces were investigated using data from field investigations, air monitoring, pulmonary radiological examinations, cell staining, and lung biopsies. The patients had long-term occupational exposure to paraffin. X-ray diffraction testing revealed that the raw material from the workshop was paraffin crystal. The air concentrations of paraffin aerosol in workplaces were significantly higher than outdoor background levels. Small diffuse and miliary shadows with unclear edges were observed throughout the whole lungs via radiography. Computed tomography revealed diffuse punctate nodules and a high density of stripe-like shadows in both lungs (ground-glass opacity in a lower lobe, and a mass-like lesion and high translucent area near the bottom of the lung). Lipid-laden macrophages were found in the sputum and bronchial lavage. A broadened alveolar septum and local focal fibrosis were also discovered via lung biopsy. The inflammatory reaction in the lung tissues appeared to resolve over time. These three rare cases of chronic LP in workers during molding and repair processes were associated with occupational paraffin aerosol exposure. Therefore, primary prevention is essential for molding or repairing workers in the iron foundry, and a differential diagnosis of occupational chronic LP (vs. pneumoconiosis) should be considered when treating these workers.

  14. Staining of E-selectin ligands on paraffin-embedded sections of tumor tissue.

    Science.gov (United States)

    Carrascal, Mylène A; Talina, Catarina; Borralho, Paula; Gonçalo Mineiro, A; Henriques, Ana Raquel; Pen, Cláudia; Martins, Manuela; Braga, Sofia; Sackstein, Robert; Videira, Paula A

    2018-05-02

    The E-selectin ligands expressed by cancer cells mediate adhesion of circulating cancer cells to endothelial cells, as well as within tissue microenvironments important for tumor progression and metastasis. The identification of E-selectin ligands within cancer tissue could yield new biomarkers for patient stratification and aid in identifying novel therapeutic targets. The determinants of selectin ligands consist of sialylated tetrasaccharides, the sialyl Lewis X and A (sLe X and sLe A ), displayed on protein or lipid scaffolds. Standardized procedures for immunohistochemistry make use of the antibodies against sLe X and/or sLe A . However, antibody binding does not define E-selectin binding activity. In this study, we developed an immunohistochemical staining technique, using E-selectin-human Ig Fc chimera (E-Ig) to characterize the expression and localization of E-selectin binding sites on paraffin-embedded sections of different cancer tissue. E-Ig successfully stained cancer cells with high specificity. The E-Ig staining show high reactivity scores in colon and lung adenocarcinoma and moderate reactivity in triple negative breast cancer. Compared with reactivity of antibody against sLe X/A , the E-Ig staining presented higher specificity to cancer tissue with better defined borders and less background. The E-Ig staining technique allows the qualitative and semi-quantitative analysis of E-selectin binding activity on cancer cells. The development of accurate techniques for detection of selectin ligands may contribute to better diagnostic and better understanding of the molecular basis of tumor progression and metastasis.

  15. Randomized, Double-blind Study with Glycerol and Paraffin in Uremic Xerosis

    Science.gov (United States)

    Balaskas, Elias; Szepietowski, Jacek C.; Bessis, Didier; Ioannides, Dimitrios; Ponticelli, Claudio; Ghienne, Corinne; Taberly, Alain

    2011-01-01

    Summary Background and objectives Uremic xerosis is a bothersome condition that is poorly responsive to moisturizing and emollient therapy. Design, setting, participants, & measurements A randomized, double-blind, intraindividual (left versus right comparison), multicentric clinical study was performed on 100 patients with moderate to severe uremic xerosis for 7 days, during which the patients applied twice daily an emulsion combining glycerol and paraffin (test product) on one allocated lower leg, and the emulsion alone (comparator) on the other lower leg. This was followed by an open-labeled use of the test product on all of the xerotic areas for 49 days. The main efficacy parameter was treatment response on each lower leg, as defined by a reduction from baseline of at least two grades in a five-point clinical score on day 7. Results Among the 99 patients analyzed, the test product was highly effective with a treatment response in 72 patients (73%), whereas 44 patients (44%) responded to the comparator (P < 0.0001, intergroup analysis). This was associated with an objective reduction in the density and thickness of the scales on day 7 (P < 0.0001 compared with the comparator) and a substantial improvement of the uremic pruritus (75%) and quality of life of the patients at study end (P < 0.001, intragroup analysis). The test product was very well tolerated, with product-related local intolerance (exacerbated pruritus, local burning, or erythema) occurring in only five patients (5%). Conclusions Uremic xerosis can be managed successfully when an appropriate emollient therapy is used. PMID:21258039

  16. Measurement of Gene Expression in Archival Paraffin-Embedded Tissues

    Science.gov (United States)

    Cronin, Maureen; Pho, Mylan; Dutta, Debjani; Stephans, James C.; Shak, Steven; Kiefer, Michael C.; Esteban, Jose M.; Baker, Joffre B.

    2004-01-01

    Throughout the last decade many laboratories have shown that mRNA levels in formalin-fixed and paraffin-embedded (FPE) tissue specimens can be quantified by reverse transcriptase-polymerase chain reaction (RT-PCR) techniques despite the extensive RNA fragmentation that occurs in tissues so preserved. We have developed RT-PCR methods that are sensitive, precise, and that have multianalyte capability for potential wide use in clinical research and diagnostic assays. Here it is shown that the extent of fragmentation of extracted FPE tissue RNA significantly increases with archive storage time. Probe and primer sets for RT-PCR assays based on amplicons that are both short and homogeneous in length enable effective reference gene-based data normalization for cross comparison of specimens that differ substantially in age. A 48-gene assay used to compare gene expression profiles from the same breast cancer tissue that had been either frozen or FPE showed very similar profiles after reference gene-based normalization. A 92-gene assay, using RNA extracted from three 10-μm FPE sections of archival breast cancer specimens (dating from 1985 to 2001) yielded analyzable data for these genes in all 62 tested specimens. The results were substantially concordant when estrogen receptor, progesterone receptor, and HER2 receptor status determined by RT-PCR was compared with immunohistochemistry assays for these receptors. Furthermore, the results highlight the advantages of RT-PCR over immunohistochemistry with respect to quantitation and dynamic range. These findings support the development of RT-PCR analysis of FPE tissue RNA as a platform for multianalyte clinical diagnostic tests. PMID:14695316

  17. Adsorption of polyvinylalcohol on paraffin-water interfaces and the properties of paraffin-in-water emulsions stabilized by polyvinylalcohol : an experimental study

    NARCIS (Netherlands)

    Lankveld, J.M.G.

    1970-01-01

    The adsorption of polyvinylalcohol (PVA) on the paraffin-water interface has been studied by interfacial tension measurements and by direct measurement of the adsorption with emulsions. The aim of the study was to provide more insight into the factors which influence the adsorption of polymers

  18. Enhancement of Afterimage Colors by Surrounding Contours

    Directory of Open Access Journals (Sweden)

    Takao Sato

    2011-05-01

    Full Text Available Presenting luminance contours surrounding the adapted areas in test phase enhances color afterimages in both duration and color appearance. The presence of surrounding contour is crucial to some color phenomenon such as van Lier's afterimage, but the contour-effect itself has not been seriously examined. In this paper, we compared the contour-effect to color afterimages and to actually colored patches to examine the nature of color information subserving color-aftereffect. In the experiment, observers were adapted for 1 sec to a small colored square (red, green, yellow, or blue presented on a gray background. Then, a test field either with or without surrounding contour was presented. Observers matched the color of a test-patch located near the afterimage to the color of afterimage. It was found that the saturation of negative afterimage was almost doubled by the presence of surrounding contours. There was no effect of luminance contrast or polarity of contours. In contrast, no enhancement of saturation by surrounding contours was observed for actually colored patches even though the colors of patches were equalized to that of afterimage without contours. This dissociation in the contour-effect demonstrates the crucial difference between the color information for aftereffects and for ordinary bottom-up color perception.

  19. Thermal characterizations of the paraffin wax/low density polyethylene blends as a solid fuel

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Soojong; Moon, Heejang; Kim, Jinkon, E-mail: jkkim@kau.ac.kr

    2015-08-10

    Highlights: • Regression rate of blends fuel is higher than polymer fuel. • LDPE is an effective mixing ingredient for the combustion efficiency. • Blends fuel is a uniform mixture with two degradation steps. • LDPE plays a positive role for the low sensitivity to the thermal deformation • Blends with low LDPE content can be an effective fuel for hybrid rocket application. - Abstract: Thermal characterizations of a novel solid fuel for hybrid rocket application, based on the paraffin wax blends with low density polyethylene (LDPE) concentration of 5% (SF-5) and 10% (SF-10) were conducted. Both the increased regression rate in comparison with the polymeric fuel, and the improved combustion efficiency in comparison with the pure paraffin fuel reveal that the blend fuels achieve higher combustion performance. The morphology of the shape stabilized paraffin wax/LDPE blends was characterized by the scanning electron microscopy (SEM). Although the SEM observation indicated the blends have uniform mixtures, they showed two degradation steps confirming the immiscibility of components in the crystalline phase from thermogravimetric analysis (TGA). The differential scanning calorimeter (DSC) results showed that the melting temperature of LDPE in the blends decreased with an increase of paraffin wax content. The decreasing total specific melting enthalpy of blended fuels with decreasing paraffin wax content is in fairly good agreement with the additive rule. In thermomechanical analysis (TMA), the linear coefficient of thermal expansion (LCTE) seems to decrease with an increase of LDPE loading, however, the loaded LDPE do merely affect the LCTE in case of the blends with low LDPE concentration. It was found that a blend of low concentration of LDPE with a relatively high concentration of paraffin wax can lead to a potential novel fuel for rocket application, a contrary case with respect to the field of phase change materials (PCM) where a blend of high concentration

  20. The role of paraffin oil on the interaction between denitrifying anaerobic methane oxidation and Anammox processes.

    Science.gov (United States)

    Fu, Liang; Ding, Zhao-Wei; Ding, Jing; Zhang, Fang; Zeng, Raymond J

    2015-10-01

    Methane is sparingly soluble in water, resulting in a slow reaction rate in the denitrifying anaerobic methane oxidation (DAMO) process. The slow rate limits the feasibility of research to examine the interaction between the DAMO and the anaerobic ammonium oxidation (Anammox) process. In this study, optimized 5 % (v/v) paraffin oil was added as a second liquid phase to improve methane solubility in a reactor containing DAMO and Anammox microbes. After just addition, methane solubility was found to increase by 25 % and DAMO activity was enhanced. After a 100-day cultivation, the paraffin reactor showed almost two times higher consumption rates of NO3 (-) (0.2268 mmol/day) and NH4 (+) (0.1403 mmol/day), compared to the control reactor without paraffin oil. The microbes tended to distribute in the oil-water interface. The quantitative (q) PCR result showed the abundance of gene copies of DAMO archaea, DAMO bacteria, and Anammox bacteria in the paraffin reactor were higher than those in the control reactor after 1 month. Fluorescence in situ hybridization revealed that the percentages of the three microbes were 55.5 and 77.6 % in the control and paraffin reactors after 100 days, respectively. A simple model of mass balance was developed to describe the interactions between DAMO and Anammox microbes and validate the activity results. A mechanism was proposed to describe the possible way that paraffin oil enhanced DAMO activity. It is quite clear that paraffin oil enhances not only DAMO activity but also Anammox activity via the interaction between them; both NO3 (-) and NH4 (+) consumption rates were about two times those of the control.

  1. Mechanisms of radiation - chemical conversion of high-paraffinic crude oil

    International Nuclear Information System (INIS)

    Zaikin, Yu.A.; Zaikina, R.F.; Silverman, J.

    2002-01-01

    Complete text of publication follows. Regularities of radiation-thermal cracking (RTC) are studied in high-paraffinic oil. Irradiation of oil samples by 2 MeV electrons was performed using a special facility assembled at the electron accelerator ELU-4. The following characteristic RTC features were observed in oil with high contents of heavy paraffins: low level of isomerization in light RTC fractions; very high polymerization rate and low olefin contents in RTC products; relatively low yields of light fractions at low irradiation dose rates; increase in the molecular weight of the gasoline fraction as the irradiation dose rate grows. Similar intense polymerization of RTC products was observed in our experiments with such wastes of oil extraction as asphalt-pitch-paraffin sediments (APPS). Theoretically this feedstock contains great reserves of hydrogen, and, therefore, has high potential yields of light fractions. However, in this case RTC was accompanied by intense reactions of polymerization and chemical adsorption that limited the maximum yields of light RTC products to 40% in our experiments. A specific feature of APPS radiation-induced destruction is formation of the big amount of a reactive paraffinic residue. As a result of interaction with the polymerizing residue the light liquid fractions were completely absorbed and the heavy residue got denser and solidified after several days of exposure at room temperature. RTC regularities in heavy paraffinic oil differ from those observed both in highly viscous petroleum feedstock and light paraffin oils. We attribute these observations to the behavior of heavy alkyl radicals that initiate polymerization and isomerization in heavy paraffin fractions

  2. Thermal characterizations of the paraffin wax/low density polyethylene blends as a solid fuel

    International Nuclear Information System (INIS)

    Kim, Soojong; Moon, Heejang; Kim, Jinkon

    2015-01-01

    Highlights: • Regression rate of blends fuel is higher than polymer fuel. • LDPE is an effective mixing ingredient for the combustion efficiency. • Blends fuel is a uniform mixture with two degradation steps. • LDPE plays a positive role for the low sensitivity to the thermal deformation • Blends with low LDPE content can be an effective fuel for hybrid rocket application. - Abstract: Thermal characterizations of a novel solid fuel for hybrid rocket application, based on the paraffin wax blends with low density polyethylene (LDPE) concentration of 5% (SF-5) and 10% (SF-10) were conducted. Both the increased regression rate in comparison with the polymeric fuel, and the improved combustion efficiency in comparison with the pure paraffin fuel reveal that the blend fuels achieve higher combustion performance. The morphology of the shape stabilized paraffin wax/LDPE blends was characterized by the scanning electron microscopy (SEM). Although the SEM observation indicated the blends have uniform mixtures, they showed two degradation steps confirming the immiscibility of components in the crystalline phase from thermogravimetric analysis (TGA). The differential scanning calorimeter (DSC) results showed that the melting temperature of LDPE in the blends decreased with an increase of paraffin wax content. The decreasing total specific melting enthalpy of blended fuels with decreasing paraffin wax content is in fairly good agreement with the additive rule. In thermomechanical analysis (TMA), the linear coefficient of thermal expansion (LCTE) seems to decrease with an increase of LDPE loading, however, the loaded LDPE do merely affect the LCTE in case of the blends with low LDPE concentration. It was found that a blend of low concentration of LDPE with a relatively high concentration of paraffin wax can lead to a potential novel fuel for rocket application, a contrary case with respect to the field of phase change materials (PCM) where a blend of high concentration

  3. A review of the performance and structural considerations of paraffin wax hybrid rocket fuels with additives

    Science.gov (United States)

    Veale, Kirsty; Adali, Sarp; Pitot, Jean; Brooks, Michael

    2017-12-01

    Paraffin wax as a hybrid rocket fuel has not been comprehensively characterised, especially regarding the structural feasibility of the material in launch applications. Preliminary structural testing has shown paraffin wax to be a brittle, low strength material, and at risk of failure under launch loading conditions. Structural enhancing additives have been identified, but their effect on motor performance has not always been considered, nor has any standard method of testing been identified between research institutes. A review of existing regression rate measurement techniques on paraffin wax based fuels and the results obtained with various additives are collated and discussed in this paper. The review includes 2D slab motors that enable visualisation of liquefying fuel droplet entrainment and the effect of an increased viscosity on the droplet entrainment mechanism, which can occur with the addition of structural enhancing polymers. An increased viscosity has been shown to reduce the regression rate of liquefying fuels. Viscosity increasing additives that have been tested include EVA and LDPE. Both these additives increase the structural properties of paraffin wax, where the elongation and UTS are improved. Other additives, such as metal hydrides, aluminium and boron generally offer improvements on the regression rate. However, very little consideration has been given to the structural effects these additives have on the wax grain. A 40% aluminised grain, for example, offers a slight increase in the UTS but reduces the elongation of paraffin wax. Geometrically accurate lab-scale motors have also been used to determine the regression rate properties of various additives in paraffin wax. A concise review of all available regression rate testing techniques and results on paraffin wax based hybrid propellants, as well as existing structural testing data, is presented in this paper.

  4. Explaining preferences for home surroundings and locations

    DEFF Research Database (Denmark)

    Andersen, Hans Skifter

    2011-01-01

    This article is based on a survey carried out in Denmark that asked a random sample of the population about their preferences for home surroundings and locations. It shows that the characteristics of social surroundings are very important and can be divided into three independent dimensions......: avoiding social nuisances, preferring social homogeneity and living close to one’s social network and place of origin. The study shows that most people have many detailed preferences, whereas some have very few. This confirms an earlier theory that some people are very connected to certain places...... with given characteristics and thus do not have priorities regarding home surroundings and locations. For others, mostly young people and singles, home is just a place to sleep and relax, whereas life is lived elsewhere. For this group, there are only preferences for location and there are few specific...

  5. Numerical performance study of paraffin wax dispersed with alumina in a concentric pipe latent heat storage system

    Directory of Open Access Journals (Sweden)

    Valan Arasu Amirtham

    2013-01-01

    Full Text Available Latent heat energy storage systems using paraffin wax could have lower heat transfer rates during melting/freezing processes due to its inherent low thermal conductivity. The thermal conductivity of paraffin wax can be enhanced by employing high conductivity materials such as alumina (Al2O3. A numerical analysis has been carried out to study the performance enhancement of paraffin wax with nanoalumina (Al2O3 particles in comparison with simple paraffin wax in a concentric double pipe heat exchanger. Numerical analysis indicates that the charge-discharge rates of thermal energy can be greatly enhanced using paraffin wax with alumina as compared with a simple paraffin wax as PCM.

  6. Formulation, Casting, and Evaluation of Paraffin-Based Solid Fuels Containing Energetic and Novel Additives for Hybrid Rockets

    Science.gov (United States)

    Larson, Daniel B.; Desain, John D.; Boyer, Eric; Wachs, Trevor; Kuo, Kenneth K.; Borduin, Russell; Koo, Joseph H.; Brady, Brian B.; Curtiss, Thomas J.; Story, George

    2012-01-01

    This investigation studied the inclusion of various additives to paraffin wax for use in a hybrid rocket motor. Some of the paraffin-based fuels were doped with various percentages of LiAlH4 (up to 10%). Addition of LiAlH4 at 10% was found to increase regression rates between 7 - 10% over baseline paraffin through tests in a gaseous oxygen hybrid rocket motor. Mass burn rates for paraffin grains with 10% LiAlH4 were also higher than those of the baseline paraffin. RDX was also cast into a paraffin sample via a novel casting process which involved dissolving RDX into dimethylformamide (DMF) solvent and then drawing a vacuum on the mixture of paraffin and RDX/DMF in order to evaporate out the DMF. It was found that although all DMF was removed, the process was not conducive to generating small RDX particles. The slow boiling generated an inhomogeneous mixture of paraffin and RDX. It is likely that superheating the DMF to cause rapid boiling would likely reduce RDX particle sizes. In addition to paraffin/LiAlH4 grains, multi-walled carbon nanotubes (MWNT) were cast in paraffin for testing in a hybrid rocket motor, and assorted samples containing a range of MWNT percentages in paraffin were imaged using SEM. The fuel samples showed good distribution of MWNT in the paraffin matrix, but the MWNT were often agglomerated, indicating that a change to the sonication and mixing processes were required to achieve better uniformity and debundled MWNT. Fuel grains with MWNT fuel grains had slightly lower regression rate, likely due to the increased thermal conductivity to the fuel subsurface, reducing the burning surface temperature.

  7. Bioaccumulation and biomagnification of short and medium chain polychlorinated paraffins in different species of fish from Liaodong Bay, North China

    OpenAIRE

    Huang, Huiting; Gao, Lirong; Xia, Dan; Qiao, Lin

    2017-01-01

    Chlorinated paraffins (CPs) are highly complex technical mixtures, and the short chain chlorinated paraffins (SCCPs) are classed as persistent and have been included in the Stockholm Convention. However, there have been few studies of SCCPs and medium chain chlorinated paraffins (MCCPs) and their bioaccumulation and biomagnification in different species of fish. The present study investigated the levels, congener group profiles, bioaccumulation, and biomagnification of SCCPs and MCCPs in diff...

  8. Paraffin oil as a "methane vector" for rapid and high cell density cultivation of Methylosinus trichosporium OB3b.

    Science.gov (United States)

    Han, Bing; Su, Tao; Wu, Hao; Gou, Zhongxuan; Xing, Xin-Hui; Jiang, Hao; Chen, Yin; Li, Xin; Murrell, J Colin

    2009-06-01

    Slow growth and relatively low cell densities of methanotrophs have limited their uses in industrial applications. In this study, a novel method for rapid cultivation of Methylosinus trichosporium OB3b was studied by adding a water-immiscible organic solvent in the medium. Paraffin oil was the most effective at enhancing cell growth and final cell density. This is at least partially due to the increase of methane gas transfer between gas and medium phases since methane solubility is higher in paraffin than in water/nitrate minimal salt medium. During cultivation with paraffin oil at 5% (v/v) in the medium, M. trichosporium OB3b cells also showed higher concentrations of the intermediary metabolites, such as formic acid and pyruvic acid, and consumed more methane compared with the control. Paraffin as methane vector to improve methanotroph growth was further studied in a 5-L fermentor at three concentrations (i.e., 2.5%, 5%, and 10%). Cell density reached about 14 g dry weight per liter with 5% paraffin, around seven times higher than that of the control (without paraffin). Cells cultivated with paraffin tended to accumulate around the interface between oil droplets and the water phase and could exist in oil phase in the case of 10% (v/v) paraffin. These results indicated that paraffin could enhance methanotroph growth, which is potentially useful in cultivation of methanotrophs in large scale in industry.

  9. Zeolitic imidazolate frameworks with optimized pore structure for olefin/paraffin-separation

    Energy Technology Data Exchange (ETDEWEB)

    Paula, C.; Boehme, U.; Hartmann, M. [Erlangen-Nuernberg Univ. (Germany). Erlangen Catalysis Resource Center

    2013-11-01

    In the chemical industry, the largest part of energy is spent on separation processes such as the separation of olefin/paraffin mixtures from steam cracker effluents by low-temperature rectification. A suitable alternative to this energy and cost intensive process is separation by selective adsorption with suitable microporous adsorbent. In this work, different ZIFs (Zeolitic Imidazolate Frameworks) have been explored with respect to their separation of olefins and paraffins. The studied materials (e.g. ZIF-8 (SOD-Topology), ZIF-71 (RHO-Topology)) were selected because of their low diameter of the largest pore entrance (0.29 to 4.2 nm) which is close to the kinetic diameter of the C{sub 2} to C{sub 4} olefins and paraffins under study. In contrast to other MOF- or zeolite-based adsorbents, in ZIF-8 and ZIF-71, the paraffin is preferentially adsorbed, which is evident from the single-component adsorption isotherms at different temperature. In the corresponding mixture breakthrough curves, the olefin breaks through first and the alkane even displaces the olefin from the pores. Thus, ZIF-8 and ZIF-71 are interesting candidates for the envisaged paraffin/olefin separation. Whether the observed separation behavior is due to the structural properties of the studied ZIFs or a consequence of peculiar chemical properties is subject to further studies. (orig.) (Published in summary form only)

  10. Analysis of hepcidin expression: in situ hybridization and quantitative polymerase chain reaction from paraffin sections.

    Science.gov (United States)

    Sakuraoka, Yuhki; Sawada, Tokihiko; Shiraki, Takayuki; Park, Kyunghwa; Sakurai, Yuhichiro; Tomosugi, Naohisa; Kubota, Keiichi

    2012-07-28

    To establish methods for quantitative polymerase chain reaction (PCR) for hepcidin using RNAs isolated from paraffin-embedded sections and in situ hybridization of hepatocellular carcinoma (HCC). Total RNA from paraffin-embedded sections was isolated from 68 paraffin-embedded samples of HCC. Samples came from 54 male and 14 female patients with a mean age of 66.8 ± 7.8 years. Quantitative PCR was performed. Immunohistochemistry and in situ hybridization for hepcidin were also performed. Quantitative PCR for hepcidin using RNAs isolated from paraffin-embedded sections of HCC was performed successfully. The expression level of hepcidin mRNA in cancer tissues was significantly higher than that in non-cancer tissues. A method of in situ hybridization for hepcidin was established successfully, and this demonstrated that hepcidin mRNA was expressed in non-cancerous tissue but absent in cancerous tissue. We have established novel methods for quantitative PCR for hepcidin using RNAs isolated from paraffin-embedded sections and in situ hybridization of HCC.

  11. Diluent paraffin nature and plutonium(IV) organic solution lamination: new results and new approach

    International Nuclear Information System (INIS)

    Renard, E.V.; Ivanchenko, V.A.; Chizhov, A.A.; Neumojev, N.V.

    1994-01-01

    The knowledge of the relation between the diluent composition and structure and the critical (maximum achievable) concentration (CC(Me)) of metals, including plutonium(IV), in the organic phase is an actual goal of a radiochemical extraction technology (PUREX process). Using γ-spectrometry analysis with high accuracy, the parameter CC(Pu) has been determined in application to Pu(IV) nitrate solution in 30% (vol.) TBP diluent solutions. n-Paraffins C 10 C 16 , iso-paraffins (mono- and dimethylderivatives), iso-paraffins with C-quaternare atoms (hydrogenated mixtures of tetra- and pentapropylene isomers) have been used as diluents. Regular correlations between CC(Pu) parameters and some individual (and mixture) diluent structure characteristics, including practically linear inversely proportional decrease of CC(Pu) with C-atom number increase (in molecules of n-C n H 2n+2 ), symbatically development of this relation to both the paraffin types (n- and iso-) have been found. The general straight proportional relation between CC(Pu)-parameter and fluidity (F=1/η, where η-dynamic viscosity at given temperature) has been discovered for all paraffins investigated - both individual and mixtures - at different temperatures. ((orig.))

  12. Smart Chips for Smart Surroundings -- 4S

    NARCIS (Netherlands)

    Schuler, Eberhard; König, Ralf; Becker, Jürgen; Rauwerda, G.K.; van de Burgwal, M.D.; Smit, Gerardus Johannes Maria; Cardoso, João M.P.; Hübner, Michael

    2011-01-01

    The overall mission of the 4S project (Smart Chips for Smart Surroundings) was to define and develop efficient flexible, reconfigurable core building blocks, including the supporting tools, for future Ambient System Devices. Reconfigurability offers the needed flexibility and adaptability, it

  13. Childhood Suicide and Myths Surrounding It.

    Science.gov (United States)

    Greene, Dorothea B.

    1994-01-01

    Dispels five misconceptions surrounding the suicide of children: that children under the age of six do not commit suicide; that suicide in latency years is extremely rare; that psychodynamically and developmentally true depression is not possible in childhood; that child cannot understand finality of death; and that children are cognitively and…

  14. Fore shock activity and its probabilistic relation to earthquake occurrence in Albania and the surrounding area

    Energy Technology Data Exchange (ETDEWEB)

    Peci, V. [Seismological Institute, Tirana (Albania); Maeda, K. [Meteorologial Research Institute, Tsukuba, Ibaraki (Japan). Dept. of Seismology and Volcanology Research; Matsmura, K.; Irikura, K. [Kyoto Univ., Kyoto (Japan). Inst. of Disaster Prevention Research

    1999-10-01

    The paper investigates some characteristics of fore shock activity of moderate and large earthquakes which occurred in the present century in Albania and the surrounding area. Using a prediction algorithm, based on possible fore shocks, the authors obtained a probabilistic relation between possible fore shocks and main shocks. Results recorded between 1901-1994 are analysed and discussed.

  15. Identification of β-SiC surrounded by relatable surrounding diamond ...

    Indian Academy of Sciences (India)

    β-SiC is identified in the presence of a relatable surrounding diamond medium using subtle, but discernible Raman ... Change in the nature of the surrounding material structure and its .... intensity implies very low graphite content in thin film. In.

  16. A case report of Anisakis pegreffii (Nematoda, Anisakidae) identified from archival paraffin sections of a Croatian patient.

    Science.gov (United States)

    Mladineo, Ivona; Popović, Marijana; Drmić-Hofman, Irena; Poljak, Vedran

    2016-02-01

    This is the first report of anisakiasis in a Croatian patient, evidenced from an archival paraffin-embedded and hematoxylin-eosin stained tissue section. Anisakiasis has been only suspected in the country based on previously detected anti-Anisakis IgE seroprevalence in the healthy coastal population, as well as an acute case where pathohistological and serological findings suggested the diseases, but the migrating larva has not been retrieved. Seventy years-old female, operated in 1998 for pulmonary carcinoma, was admitted to the General hospital Šibenik, Croatia in 2003, because of gastric pain and nausea that lasted for couple of days. She was showing good general condition, full mobility and lucidity, subfebrile status. Abdominal palpation inferred acute pain in paraumbilical and ileocecal region. Exploratory right pararectal laparotomy revealed a hardened, 5 cm-long structure, located intraluminally in the sigmoid colon, not perforating colon serosa. The process has been dissected and sent for patohistological diagnosis. Results showed a 2 mm-long whitish nematode spiralised in muscular layer of colon mucosa surrounded by granulomatous inflammation. After genomic DNA isolation of the nematode from the histological section, and amplification at the mitochondrial cytochrome oxidase 2 locus, etiological agent has been identified as Anisakis pegreffii. Used methodology suggests that screening of archival suspicious sections is feasible in order to study epidemiology of this zoonotic disease poorly recognised in Croatia.

  17. A nano-graphite/paraffin phase change material with high thermal conductivity

    International Nuclear Information System (INIS)

    Li, Min

    2013-01-01

    Highlights: ► Paraffin and NG formed a nanoscale compound. ► The thermal conductivity increased gradually with the content of NG. ► The thermal conductivity of the material containing 10% NG were 0.9362 W/m K. - Abstract: Nano-graphite (NG)/paraffin composites were prepared as composite phase change materials. NG has the function of improving the thermal conductivity of the composite. The microstructure and thermal properties of the materials were examined with environmental scanning electron microscopy and differential scanning calorimetry. The results indicated that the NG layers were randomly dispersed in the paraffin, and the thermal conductivity increased gradually with the content of NG. Thermal conductivity of the material containing 10% NG were 0.9362 W/m K

  18. Microwave reflection properties of planar anisotropy Fe50Ni50 powder/paraffin composites

    International Nuclear Information System (INIS)

    Wei Jian-Qiang; Zhang Zhao-Qi; Han Rui; Wang Tao; Li Fa-Shen

    2012-01-01

    The reflection properties of planar anisotropy Fe 50 Ni 50 powder/paraffin composites have been studied in the microwave frequency range. The permeability of Fe 50 Ni 50 powder/paraffin composites is greatly enhanced by introducing the planar anisotropy, and can be further enhanced by using a rotational orientation method. The complex permeability can be considered as the superposition of two types of magnetic resonance. The resonance peak at high frequency is attributed to the natural resonance, while the peak at low frequency is attributed to the domain-wall resonance. The simulated results of the microwave reflectivity show that the matching thickness, peak frequency, permeability, and permittivity are closely related to the quarter wavelength matching condition. The Fe 50 Ni 50 powder/paraffin composites can be attractive candidates for thinner microwave absorbers in the L-band (1–2 GHz). (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  19. Amplification of chromosomal translocation junctions from paraffin-embedded tissues of follicular lymphoma patients

    International Nuclear Information System (INIS)

    Nambiar, Mridula; Raghavan, Sathees C; Choudhary, Bibha; Rao, Clementina R

    2008-01-01

    Follicular lymphoma is associated with the t(14;18) translocation, which is one of the most common chromosomal translocations in cancer. Generally, tissues from such patients are preserved as formalin-fixed and paraffin-embedded samples. Most of the time, retrieving the molecular information from such samples is hampered due to quality of preservation, extraction procedures and reaction conditions. In the present study, we isolate the chromosomal DNA from the paraffin-embedded nodal tissues of lymphoma patients and use a highly sensitive nested PCR approach to detect t(14;18) translocation. Our studies show that despite the sheared DNA obtained, appropriate modification of PCR reaction conditions can help in obtaining the desired amplifications. The DNA extraction protocol from paraffin-embedded nodal tissues and modifications in the PCR conditions are discussed. This study would contribute to the successful use of archival tissue samples in obtaining valuable information for cancer research

  20. Amplification of chromosomal translocation junctions from paraffin-embedded tissues of follicular lymphoma patients

    Energy Technology Data Exchange (ETDEWEB)

    Nambiar, Mridula; Raghavan, Sathees C [Department of Biochemistry, Indian Institute of Science, Bangalore-560 012 (India); Choudhary, Bibha [Manipal Institute of Regenerative Medicine, Manipal University, Bangalore-560 071 (India); Rao, Clementina R [Department of Pathology, Kidwai Memorial Institute of Oncology, Bangalore-560 029 (India)], E-mail: sathees@biochem.iisc.ernet.in

    2008-09-01

    Follicular lymphoma is associated with the t(14;18) translocation, which is one of the most common chromosomal translocations in cancer. Generally, tissues from such patients are preserved as formalin-fixed and paraffin-embedded samples. Most of the time, retrieving the molecular information from such samples is hampered due to quality of preservation, extraction procedures and reaction conditions. In the present study, we isolate the chromosomal DNA from the paraffin-embedded nodal tissues of lymphoma patients and use a highly sensitive nested PCR approach to detect t(14;18) translocation. Our studies show that despite the sheared DNA obtained, appropriate modification of PCR reaction conditions can help in obtaining the desired amplifications. The DNA extraction protocol from paraffin-embedded nodal tissues and modifications in the PCR conditions are discussed. This study would contribute to the successful use of archival tissue samples in obtaining valuable information for cancer research.

  1. Determination Of Adsorption And Paraffin Characterization Of Treatment To Adsorb Vegetable Oil

    International Nuclear Information System (INIS)

    Aminah, Neneng Siti; Mulijani, Sri; Sudirman; Ridwan

    2004-01-01

    Using vegetable oil repeatedly, beside affect on quality decline of food and the oil itself, it is harmful to human health. Some poisoning and carcinogenic symptom were founded with experiment using animals. According to that fact, the aim of the research is using paraffin and candle to adsorb used vegetable oil and to convert into solid sample, so it can be easily wasted. At first, 2 g of sample was poured into the heated oil, with gently stirrer until it turned cold and harden. Each sample and standard before and after treatment was characterized with Ftir, XRD, and DSc. The result shows that paraffins adsorbs 40 ml used vegetable oil with 2 g sample in proportion. That proportion is lower than the standard which can adsorb 66.67 ml vegetable oil in the same weight sample. The difference of paraffin and standard is caused by physical properties within that two materials, and it can be explained by Ftir, X-Ray Diffraction (XRD) and differential scanning calorimetry (DSc). Based on result of Ftir analysis, standard consented of saturated hydrocarbon compound (alkanes) whereas paraffin consisted of unsaturated hydrocarbon compound (alkenes). Infrared spectrum after treatment showed the changes of compound, O-H and esters group were formed and it shows characterised the adsorption process. The result of DSc analysis showed that crystalline the melting point of standard is 75,3 o C and paraffin is 54,17 o C. The result of analysis XRD, described that standard and paraffin before treatment are crystalline whereas after treatment are am orf

  2. Simulation and sensitivity analysis for heavy linear paraffins production in LAB production Plant

    Directory of Open Access Journals (Sweden)

    Karimi Hajir

    2014-12-01

    Full Text Available Linear alkyl benzene (LAB is vastly utilized for the production of biodegradable detergents and emulsifiers. Predistillation unit is a part of LAB production plant in which that produced heavy linear paraffins (nC10-nC13. In this study, a mathematical model has been developed for heavy linear paraffins production in distillation columns, which has been solved using a commercial code. The models have been validated by the actual data. The effects of process parameters such as reflux rate, and reflux temperature using Gradient Search technique has been investigated. The sensitivity analysis shows that optimum reflux in columns are achieved.

  3. A method for removing sulfur bearing compounds from paraffinous hydrocarbons or a directly distilled benzine fraction

    Energy Technology Data Exchange (ETDEWEB)

    Konyukhova, T.P.; Bolotskaya, I.A.; Mikhaylova, L.A.; Sadykov, A.N.; Shitovkin, N.T.; Vlasov, V.V.

    1983-01-01

    In the known method for removing sulfurorganic compounds from paraffinous hydrocarbons or a directly distilled gasoline fraction through their adsorption using natural zeolite, in order to increase the degree of purification, clinoptilolite (Kp), which contains SiO2 and A12O3 in a molar ratio of 10.6 to 16.7 is used as the natural zeolite. The purification of the paraffinous hydrocarbons through clinoptilolite adsorption as compared with mordenite adsorption makes it possible to increase the degree of their purification of ethylmercaptane and dimethylsulfide. The effectiveness of clinoptilolite is also confirmed in removing mercaptanes and sulfides from directly distilled gasoline fractions.

  4. A rapid method of reprocessing for electronic microscopy of cut histological in paraffin

    International Nuclear Information System (INIS)

    Hernandez Chavarri, F.; Vargas Montero, M.; Rivera, P.; Carranza, A.

    2000-01-01

    A simple and rapid method is described for re-processing of light microscopy paraffin sections to observe they under transmission electron microscopy (TEM) and scanning electron microscopy (SEM) The paraffin-embedded tissue is sectioned and deparaffinized in toluene; then exposed to osmium vapor under microwave irradiation using a domestic microwave oven. The tissues were embedded in epoxy resin, polymerized and ultrathin sectioned. The method requires a relatively short time (about 30 minutes for TEM and 15 for SEM), and produces a reasonable quality of the ultrastructure for diagnostic purposes. (Author) [es

  5. Sampling and transport of paraffin waste form from CWDS of nuclear power plant

    International Nuclear Information System (INIS)

    Lee, J. M.; Hwang, J. H.; Kim, C. R.; Park, J. W.

    2000-01-01

    Sampling and transport of paraffin waste form from concentrated waste drying system (CWDS) of domestic nuclear power plant were performed to collect the leaching characteristic data for the disposal of radioactive waste. Transport was performed according to the national regulations and the internal rules of the nuclear power plant. The sample of paraffin waste form was classified as L type package according to the regulation and radiation exposure of operator was measured in the range of 6 to 12 mrem that was less than the estimated amount

  6. Paraffin Granuloma Associated with Buried Glans Penis-Induced Sexual and Voiding Dysfunction

    Directory of Open Access Journals (Sweden)

    Wonhee Chon

    2017-08-01

    Full Text Available A paraffinoma is a type of inflammatory lipogranuloma that develops after the injection of an artificial mineral oil, such as paraffin or silicon, into the foreskin or the subcutaneous tissue of the penis for the purpose of penis enlargement, cosmetics, or prosthesis. The authors experienced a case of macro-paraffinoma associated with sexual dysfunction, voiding dysfunction, and pain caused by a buried glans penis after a paraffin injection for penis enlargement that had been performed 35 years previously. Herein, this case is presented with a literature review.

  7. Paraffin Granuloma Associated with Buried Glans Penis-Induced Sexual and Voiding Dysfunction.

    Science.gov (United States)

    Chon, Wonhee; Koo, Ja Yun; Park, Min Jung; Choi, Kyung Un; Park, Hyun Jun; Park, Nam Cheol

    2017-08-01

    A paraffinoma is a type of inflammatory lipogranuloma that develops after the injection of an artificial mineral oil, such as paraffin or silicon, into the foreskin or the subcutaneous tissue of the penis for the purpose of penis enlargement, cosmetics, or prosthesis. The authors experienced a case of macro-paraffinoma associated with sexual dysfunction, voiding dysfunction, and pain caused by a buried glans penis after a paraffin injection for penis enlargement that had been performed 35 years previously. Herein, this case is presented with a literature review. Copyright © 2017 Korean Society for Sexual Medicine and Andrology.

  8. Determination of paraffins in food simulants and packaging materials by liquid chromatography with evaporative mass detection and identification of paraffin type by liquid chromatography/gas chromatography and fourier transform infrared spectroscopy

    NARCIS (Netherlands)

    Simal-Gándara, J.; Sarria-Vidal, M.; Rijk, M.A.H.

    2000-01-01

    A liquid chromatographic method with evaporative mass detection (EMD) is described for the determination of paraffins in food contact materials that do not contain polyolefin oligomers, or paraffins migrating from these materials into fatty food simulants or certain simple foods. A normal-phase

  9. Preparation and characterization of form-stable paraffin/polycaprolactone composites as phase change materials for thermal energy storage

    Directory of Open Access Journals (Sweden)

    Aludin M.S.

    2017-01-01

    Full Text Available Paraffin is Phase Change Materials (PCM that possesses desirable properties such as high thermal energy storage and thermal stability to make it suitable for thermal energy storage applications. However, paraffin has been reported to leak out during the melting process. In this study, composites were prepared by dissolving paraffin and polycaprolactone (PCL at varied mass percent compositions in chloroform and then purified through precipitation techniques. The leakage test was conducted by placing the composite samples on a set of four-layer filter papers and left in a furnace at 90°C for 1 hour. By incorporating PCL into paraffin phase, the leakage mass percentage was drastically reduced. The PCL polymer matrix in the composites may have trapped the paraffin molecules during melting process thus prevent it from leaking.

  10. Screening of short- and medium-chain chlorinated paraffins in selected riverine sediments and sludge from the Czech Republic.

    Science.gov (United States)

    Pribylová, Petra; Klánová, Jana; Holoubek, Ivan

    2006-11-01

    Wide distribution of chlorinated paraffins in the environment has already been demonstrated in several studies; however, information about their levels in the Central Europe is still very limited. First study focused on the SCCP contamination of the Czech aquatic environment have been performed recently, and its results motivated the authors to analyze sediments from a wide set of the Czech rivers in order to obtain more detailed information. Thirty-six sediment samples from eleven rivers and five drainage vents neighboring the chemical factories were analyzed; special attention was paid to the industrial areas. For the first time in the Czech Republic, medium-chain in addition to short-chain chlorinated paraffins were analyzed using GC-ECNI-MS. Chlorinated paraffins were detected in sediment samples on the concentration levels up to 347 ngg(-1) for short-chain chlorinated paraffins, and 5575 ngg(-1) for medium-chain chlorinated paraffins. Average chlorination degree of SCCPs was 65%.

  11. Preparation of Paraffin@Poly(styrene-co-acrylic acid) Phase Change Nanocapsules via Combined Miniemulsion/Emulsion Polymerization.

    Science.gov (United States)

    Zhang, Feng; Liu, Tian-Yu; Hou, Gui-Hua; Guan, Rong-Feng; Zhang, Jun-Hao

    2018-06-01

    The fast development of solid-liquid phase change materials calls for nanomaterials with large specific surface area for rapid heat transfer and encapsulation of phase change materials to prevent potential leakage. Here we report a combined miniemulsion/emulsion polymerization method to prepare poly(styrene-co-acrylic acid)-encapsulated paraffin (paraffin@P(St-co-AA)) nanocapsules. The method could suppress the shortcomings of common miniemulsion polymerization (such as evaporation of monomer and decomposition of initiator during ultrasonication). The paraffin@P(St-co-AA) nanocapsules are uniform in size and the polymer shell can be controlled by the weight ratio of St to paraffin. The phase change behavior of the nanocapsules is similar to that of pure paraffin. We believe our method can also be utilized to synthesize other core-shell phase change materials.

  12. Reference moderator calculated performance for the LANSCE upgrade project

    International Nuclear Information System (INIS)

    Ferguson, P.D.; Russell, G.J.; Pitcher, E.J.

    1995-01-01

    The authors have calculated the performance of five moderators of interest to the LANSCE upgrade project. Coupled and decoupled light water and liquid hydrogen moderators in flux-trap geometry surrounded by a neutronically infinite heavy-water cooled beryllium reflector have been studied. Time and energy spectra, as well as semi-empirical fits to the data, are presented. The data has been made available to aid the instrument design and moderator selection process

  13. Preparation and thermal energy storage properties of paraffin/calcined diatomite composites as form-stable phase change materials

    International Nuclear Information System (INIS)

    Sun, Zhiming; Zhang, Yuzhong; Zheng, Shuilin; Park, Yuri; Frost, Ray L.

    2013-01-01

    Highlights: ► Composite phase change material (PCM) was prepared by blending composite paraffin and calcined diatomite. ► The optimum mixed proportion was obtained through differential scanning calorimetry. ► Thermal energy storage properties of the composite PCMs were determined by DSC. ► Thermal cycling test showed that the prepared PCMs are thermally reliable and chemically stable. - Abstract: A composite paraffin-based phase change material (PCM) was prepared by blending composite paraffin and calcined diatomite through the fusion adsorption method. In this study, raw diatomite was purified by thermal treatment in order to improve the adsorption capacity of diatomite, which acted as a carrier material to prepare shape-stabilized PCMs. Two forms of paraffin (paraffin waxes and liquid paraffin) with different melting points were blended together by the fusion method, and the optimum mixed proportion with a suitable phase-transition temperature was obtained through differential scanning calorimetry (DSC) analysis. Then the prepared composite paraffin was adsorbed in calcined diatomite. The prepared paraffin/calcined diatomite composites were characterized by the scanning electron microscope (SEM) and Fourier transformation infrared (FT-IR) analysis techniques. Thermal energy storage properties of the composite PCMs were determined by DSC method. DSC results showed that there was an optimum adsorption ratio between composite paraffin and calcined diatomite and the phase-transition temperature and the latent heat of the composite PCMs were 33.04 °C and 89.54 J/g, respectively. Thermal cycling test of composite PCMs showed that the prepared material is thermally reliable and chemically stable. The obtained paraffin/calcined diatomite composites have proper latent heat and melting temperatures, and show practical significance and good potential application value

  14. Preparation and thermal energy storage properties of paraffin/calcined diatomite composites as form-stable phase change materials

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Zhiming [School of Chemical and Environmental Engineering, China University of Mining and Technology, Beijing 100083 (China); Chemistry Discipline, Faculty of Science and Technology, Queensland University of Technology, 2 George Street, GPO Box 2434, Brisbane, Queensland 4001 (Australia); Zhang, Yuzhong [School of Chemical and Environmental Engineering, China University of Mining and Technology, Beijing 100083 (China); Zheng, Shuilin, E-mail: shuilinzh@yahoo.com.cn [School of Chemical and Environmental Engineering, China University of Mining and Technology, Beijing 100083 (China); Park, Yuri [Chemistry Discipline, Faculty of Science and Technology, Queensland University of Technology, 2 George Street, GPO Box 2434, Brisbane, Queensland 4001 (Australia); Frost, Ray L., E-mail: r.frost@qut.edu.au [Chemistry Discipline, Faculty of Science and Technology, Queensland University of Technology, 2 George Street, GPO Box 2434, Brisbane, Queensland 4001 (Australia)

    2013-04-20

    Highlights: ► Composite phase change material (PCM) was prepared by blending composite paraffin and calcined diatomite. ► The optimum mixed proportion was obtained through differential scanning calorimetry. ► Thermal energy storage properties of the composite PCMs were determined by DSC. ► Thermal cycling test showed that the prepared PCMs are thermally reliable and chemically stable. - Abstract: A composite paraffin-based phase change material (PCM) was prepared by blending composite paraffin and calcined diatomite through the fusion adsorption method. In this study, raw diatomite was purified by thermal treatment in order to improve the adsorption capacity of diatomite, which acted as a carrier material to prepare shape-stabilized PCMs. Two forms of paraffin (paraffin waxes and liquid paraffin) with different melting points were blended together by the fusion method, and the optimum mixed proportion with a suitable phase-transition temperature was obtained through differential scanning calorimetry (DSC) analysis. Then the prepared composite paraffin was adsorbed in calcined diatomite. The prepared paraffin/calcined diatomite composites were characterized by the scanning electron microscope (SEM) and Fourier transformation infrared (FT-IR) analysis techniques. Thermal energy storage properties of the composite PCMs were determined by DSC method. DSC results showed that there was an optimum adsorption ratio between composite paraffin and calcined diatomite and the phase-transition temperature and the latent heat of the composite PCMs were 33.04 °C and 89.54 J/g, respectively. Thermal cycling test of composite PCMs showed that the prepared material is thermally reliable and chemically stable. The obtained paraffin/calcined diatomite composites have proper latent heat and melting temperatures, and show practical significance and good potential application value.

  15. Methanogenic biodegradation of paraffinic solvent hydrocarbons in two different oil sands tailings.

    Science.gov (United States)

    Mohamad Shahimin, Mohd Faidz; Siddique, Tariq

    2017-04-01

    Microbial communities drive many biogeochemical processes in oil sands tailings and cause greenhouse gas emissions from tailings ponds. Paraffinic solvent (primarily C 5 -C 6 ; n- and iso-alkanes) is used by some oil sands companies to aid bitumen extraction from oil sands ores. Residues of unrecovered solvent escape to tailings ponds during tailings deposition and sustain microbial metabolism. To investigate biodegradation of hydrocarbons in paraffinic solvent, mature fine tailings (MFT) collected from Albian and CNRL ponds were amended with paraffinic solvent at ~0.1wt% (final concentration: ~1000mgL -1 ) and incubated under methanogenic conditions for ~1600d. Albian and CNRL MFTs exhibited ~400 and ~800d lag phases, respectively after which n-alkanes (n-pentane and n-hexane) in the solvent were preferentially metabolized to methane over iso-alkanes in both MFTs. Among iso-alkanes, only 2-methylpentane was completely biodegraded whereas 2-methylbutane and 3-methylpentane were partially biodegraded probably through cometabolism. 16S rRNA gene pyrosequencing showed dominance of Anaerolineaceae and Methanosaetaceae in Albian MFT and Peptococcaceae and co-domination of "Candidatus Methanoregula" and Methanosaetaceae in CNRL MFT bacterial and archaeal communities, respectively, during active biodegradation of paraffinic solvent. The results are important for developing future strategies for tailings reclamation and management of greenhouse gas emissions. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. Real-time quantitative PCR of microdissected paraffin-embedded breast carcinoma

    DEFF Research Database (Denmark)

    Gjerdrum, Lise Mette; Sorensen, Boe Sandahl; Kjeldsen, Eigil

    2004-01-01

    We studied the feasibility of using real-time quantitative PCR to determine HER-2 DNA amplification and mRNA expression in microdissected formalin-fixed, paraffin-embedded breast tumors and compared this with standard immunohistochemistry (IHC) and fluorescent in situ hybridization (FISH) methods...

  17. Application of magnetic tools designed by Ecopetrol to inhibit paraffin in the production systems

    International Nuclear Information System (INIS)

    Medina Z, Carlos; Pelaez U, Carlos; Buendia I, Hernando; Pena C, Alvaro

    1995-01-01

    The present article narrates the experiences and the results obtained with these tools in 3 representative historical cases of a group of 16, using a technique of magnetic inhibition of paraffin which has been proven with great success in diverse parts of the world, making of this a non expensive inhibition method and of continuous treatment

  18. Developments and interlaboratory study of the analysis of short-chain chlorinated paraffins

    NARCIS (Netherlands)

    van Mourik, L. M.; van der Veen, I.; Crum, S.; de Boer, J.

    To survey the conformity and quality of the results between laboratories for short-chain chlorinated paraffins (SCCPs) determination, we reviewed current and novel analytical methods and organized four worldwide laboratory exercises between 2011 and 2017. Participants were requested to analyse test

  19. Developments and interlaboratory study of the analysis of short-chain chlorinated paraffins

    NARCIS (Netherlands)

    Mourik, van L.M.; Veen, van der I.; Crum, S.; Boer, de J.

    2018-01-01

    To survey the conformity and quality of the results between laboratories for short-chain chlorinated paraffins (SCCPs) determination, we reviewed current and novel analytical methods and organized four worldwide laboratory exercises between 2011 and 2017. Participants were requested to analyse test

  20. Analysis of Steam Heating of a Two-Layer TBP/N-Paraffin/Nitric Acid Mixtures

    International Nuclear Information System (INIS)

    Laurinat, J.E.; Hassan, N.M.; Rudisill, T.S.; Askew, N.M.

    1998-01-01

    This report presents an analysis of steam heating of a two-layer tri-n-butyl phosphate (TBP)/n-paraffin-nitric acid mixture.The purpose of this study is to determine if the degree of mixing provided by the steam jet or by bubbles generated by the TBP/nitric acid reaction is sufficient to prevent a runaway reaction

  1. Thermal characterization of polymer matrix composites containing microencapsulated paraffin in solid or liquid state

    International Nuclear Information System (INIS)

    Sari-Bey, Sana; Fois, Magali; Krupa, Igor; Ibos, Laurent; Benyoucef, Boumédiène

    2014-01-01

    Highlights: • Thermal characterization of PCL/Micronal composites. • Melting enthalpy and heat capacity measured by DSC. • Interest: have measured thermal properties at different temperatures. • Thermophysical properties measurement temperatures chosen outside phase changes. • Characteristics useful to model composites heat transfer for LHTES applications. - Abstract: This work focuses on the study of heat transfer mechanisms in composites materials which may be used for Latent Heat Thermal Energy Storage applications. These composites contain phase change material (PCM) which can absorb and release energy during thermal cycling. PCM’s used here are paraffins microencapsulated in poly(methylmethacrylate); microencapsulation avoids the flow of paraffin when it is in the liquid state. Samples with different paraffin weight fractions and particles shape and distribution were studied in this work. Scanning Electron Microscopy and Differential Scanning Calorimetry were used to determine morphology and perform measurements of phase changes temperatures, enthalpies and heat capacity respectively. Further, a periodic method (DICO) allowed measuring thermal conductivity (λ) and diffusivity (a) of the composites at temperatures below and above of the paraffin phase change from crystalline solid to isotropic liquid

  2. Detection of apoptosis in paraffin embedded tissues: the influence of tissue type and fixation

    Czech Academy of Sciences Publication Activity Database

    Matalová, Eva; Dubská, L.; Míšek, Ivan

    2002-01-01

    Roč. 71, č. 4 (2002), s. 529-533 ISSN 0001-7213 R&D Projects: GA ČR GP204/02/P112; GA AV ČR KSK6005114 Keywords : apoptosis * TUNEL test * paraffin embedded tissues Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 0.370, year: 2002

  3. Paraffin Nanocomposites for Heat Management of Lithium-Ion Batteries: A Computational Investigation

    Directory of Open Access Journals (Sweden)

    A. H. N. Shirazi

    2016-01-01

    Full Text Available Lithium-ion (Li-ion batteries are currently considered as vital components for advances in mobile technologies such as those in communications and transport. Nonetheless, Li-ion batteries suffer from temperature rises which sometimes lead to operational damages or may even cause fire. An appropriate solution to control the temperature changes during the operation of Li-ion batteries is to embed batteries inside a paraffin matrix to absorb and dissipate heat. In the present work, we aimed to investigate the possibility of making paraffin nanocomposites for better heat management of a Li-ion battery pack. To fulfill this aim, heat generation during a battery charging/discharging cycles was simulated using Newman’s well established electrochemical pseudo-2D model. We couple this model to a 3D heat transfer model to predict the temperature evolution during the battery operation. In the later model, we considered different paraffin nanocomposites structures made by the addition of graphene, carbon nanotubes, and fullerene by assuming the same thermal conductivity for all fillers. This way, our results mainly correlate with the geometry of the fillers. Our results assess the degree of enhancement in heat dissipation of Li-ion batteries through the use of paraffin nanocomposites. Our results may be used as a guide for experimental set-ups to improve the heat management of Li-ion batteries.

  4. Drug release from non-aqueous suspensions. II. The release of methylxanthines from paraffin suspensions

    NARCIS (Netherlands)

    Blaey, C.J. de; Fokkens, J.G.

    1984-01-01

    The release of 3 methylxanthines, i.e. caffeine, theobromine and theophylline, from suspensions in liquid paraffin to an aqueous phase was determined in an in vitro apparatus. The release rates were determined as a function of the pH of the aqueous phase. It was proved that the release process was

  5. The impact of child-resistant containers on the incidence of paraffin ...

    African Journals Online (AJOL)

    The commonest cause of accidental poisoning in the South African black paediatric population is paraffin ingestion. In this intervention study a specifically designed child-resistant container (CRG) was introduced to evaluate whether its use would decrease the incidence ofparaffin ingestion. CRCs were distributed to 20 000 ...

  6. Virus characterization and discovery in formalin-fixed paraffin-embedded tissues

    NARCIS (Netherlands)

    Bodewes, Rogier; van Run, Peter R W A; Schürch, Anita C; Koopmans, Marion P G; Osterhaus, Albert D M E; Baumgärtner, Wolfgang; Kuiken, Thijs; Smits, Saskia L

    2015-01-01

    Detection and characterization of novel viruses is hampered frequently by the lack of properly stored materials. Especially for the retrospective identification of viruses responsible for past disease outbreaks, often only formalin-fixed paraffin-embedded (FFPE) tissue samples are available.

  7. Thermal properties and crystallization behaviour of solid N-paraffin components derived from Mukta crude oil

    Czech Academy of Sciences Publication Activity Database

    Khan, H. U.; Nautiyal, S. P.; Agrawal, K. M.; Sharma, R. L.; Sikora, Antonín

    2001-01-01

    Roč. 43, č. 1 (2001), s. 13-16 ISSN 1335-3055 R&D Projects: GA AV ČR KSK4050111 Institutional research plan: CEZ:AV0Z4050913 Keywords : paraffin s * crude oil * urea adductables Subject RIV: CD - Macromolecular Chemistry

  8. Technical and Economic Analysis of Injecting Enhancers into High-Paraffin Oil Heaters

    Science.gov (United States)

    Konakhina, I. A.; Khamidullina, G. R.; Khusnutdinova, E. M.

    2017-09-01

    This paper covers an algorithm of how to optimize the selection of preferred solutions to upgrade heat-exchange equipment. The algorithm is discussed in terms of high-paraffin oil heaters as compared with other heat-exchange surface features.

  9. Antibacterial and antifungal effect of high pH and paraffin wax ...

    African Journals Online (AJOL)

    The antibacterial and antifungal effects of high pH (9, 10) and paraffin wax were determined. Determination of antibacterial and antifungal activity of the combined treatments was achieved by aerobic mesophilic count of bacteria and fungi on the surface of the tomatoes, peppers and oranges using serial dilution and pour ...

  10. Effect of functional groups on thermal conductivity of graphene/paraffin nanocomposite

    Energy Technology Data Exchange (ETDEWEB)

    Zabihi, Zabiholah; Araghi, Houshang, E-mail: araghi@aut.ac.ir

    2016-11-25

    In this paper, thermal conductivity of graphene/paraffin nanocomposite using micromechanical model has been studied. The behavior of thermal conductivity of nanocomposite as a function of volume fraction of graphene is studied. Then is shown that as the interfacial thermal resistance at the graphene–paraffin interface decreases, the thermal conductivity of nanocomposite increases. In order to reduce the interfacial thermal resistance, functional groups in the interface between graphene and paraffin are used. It can be observed that using functional groups of hydrogen, methyl and phenyl in the interface of nanocomposite, contributes to the improvement of the thermal conductivity. Moreover, as the rate of coverage of the surface of graphene with functional groups of H, CH{sub 3} and C{sub 6}H{sub 5} increases, the thermal conductivity of nanocomposite improves. - Highlights: • Thermal conductivity nanocomposite exhibit nonlinear behavior with volume faction. • Phenyl is better to form the thermal conductivity network in paraffin. • The thickness of interfacial layer can be obtained 12.75 nm.

  11. Effect of microbial treatment on the prevention and removal of paraffin deposits on stainless steel surfaces.

    Science.gov (United States)

    Xiao, Meng; Li, Wen-Hong; Lu, Mang; Zhang, Zhong-Zhi; Luo, Yi-Jing; Qiao, Wei; Sun, Shan-Shan; Zhong, Wei-Zhang; Zhang, Min

    2012-11-01

    In this study, biosurfactant-producing strain N2 and non-biosurfactant producing stain KB18 were used to investigate the effects of microbial treatment on the prevention and removal of paraffin deposits on stainless steel surfaces. Strain N2, with a biosurfactant production capacity, reduced the contact angle of stainless steel to 40.04°, and the corresponding adhesion work of aqueous phase was decreased by 26.5 mJ/m(2). By contrast, KB18 could only reduce the contact angle to 50.83°, with a corresponding 7.6 mJ/m(2) decrease in the aqueous phase work adhesion. The paraffin removal test showed that the paraffin removal efficiencies of strain N2 and KB18 were 79.0% and 61.2%, respectively. Interestingly, the N2 cells could attach on the surface of the oil droplets to inhibit droplets coalescence. These results indicate that biosurfactant-producing strains can alter the wettability of stainless steel and thus eliminate paraffin deposition. Copyright © 2012 Elsevier Ltd. All rights reserved.

  12. Hydrogen peroxide modified Mg-Al-O oxides supported Pt-Sn catalysts for paraffin dehydrogenation

    NARCIS (Netherlands)

    Lai, Y.; He, Songbo; Luo, S.; Bi, W.; Li, XianRu; Sun, Chenglin; Seshan, Kulathuiyer

    2015-01-01

    In this work, a new method to prepare Mg–Al–O oxide by co-precipitation method with addition of H2O2 was developed. The application of Mg–Al–O as a support of Pt–Sn catalysts for paraffin dehydrogenation was investigated. Characterization results indicated that modification of H2O2 (i) enlarged the

  13. Evaluating Quality of Aged Archival Formalin-Fixed Paraffin-Embedded Samples for RNA-Sequencing

    Science.gov (United States)

    Archival formalin-fixed paraffin-embedded (FFPE) samples offer a vast, untapped source of genomic data for biomarker discovery. However, the quality of FFPE samples is often highly variable, and conventional methods to assess RNA quality for RNA-sequencing (RNA-seq) are not infor...

  14. A new insert sample approach to paper spray mass spectrometry: a paper substrate with paraffin barriers.

    Science.gov (United States)

    Colletes, T C; Garcia, P T; Campanha, R B; Abdelnur, P V; Romão, W; Coltro, W K T; Vaz, B G

    2016-03-07

    The analytical performance for paper spray (PS) using a new insert sample approach based on paper with paraffin barriers (PS-PB) is presented. The paraffin barrier is made using a simple, fast and cheap method based on the stamping of paraffin onto a paper surface. Typical operation conditions of paper spray such as the solvent volume applied on the paper surface, and the paper substrate type are evaluated. A paper substrate with paraffin barriers shows better performance on analysis of a range of typical analytes when compared to the conventional PS-MS using normal paper (PS-NP) and PS-MS using paper with two rounded corners (PS-RC). PS-PB was applied to detect sugars and their inhibitors in sugarcane bagasse liquors from a second generation ethanol process. Moreover, the PS-PB proved to be excellent, showing results for the quantification of glucose in hydrolysis liquors with excellent linearity (R(2) = 0.99), limits of detection (2.77 mmol L(-1)) and quantification (9.27 mmol L(-1)). The results are better than for PS-NP and PS-RC. The PS-PB was also excellent in performance when compared with the HPLC-UV method for glucose quantification on hydrolysis of liquor samples.

  15. Opportunity's Surroundings on Sol 1818 (Vertical)

    Science.gov (United States)

    2009-01-01

    NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,818th Martian day, or sol, of Opportunity's surface mission (March 5, 2009). South is at the center; north at both ends. This view is presented as a vertical projection with geometric seam correction. North is at the top. The rover had driven 80.3 meters (263 feet) southward earlier on that sol. Tracks from the drive recede northward in this view. The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock.

  16. Opportunity's Surroundings on Sol 1818 (Polar)

    Science.gov (United States)

    2009-01-01

    NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,818th Martian day, or sol, of Opportunity's surface mission (March 5, 2009). South is at the center; north at both ends. This view is presented as a polar projection with geometric seam correction. North is at the top. The rover had driven 80.3 meters (263 feet) southward earlier on that sol. Tracks from the drive recede northward in this view. The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock.

  17. Variation in penetration of submicrometric particles through electrostatic filtering facepieces during exposure to paraffin oil aerosol.

    Science.gov (United States)

    Plebani, Carmela; Listrani, Stefano; Tranfo, Giovanna; Tombolini, Francesca

    2012-01-01

    Several studies show the increase of penetration through electrostatic filters during exposure to an aerosol flow, because of particle deposition on filter fibers. We studied the effect of increasing loads of paraffin oil aerosol on the penetration of selected particle sizes through an electrostatic filtering facepiece. FFP2 facepieces were exposed for 8 hr to a flow rate of 95.0 ± 0.5 L/min of polydisperse paraffin aerosol at 20.0 ± 0.5 mg/m(3). The penetration of bis(2-ethylhexyl)sebacate (DEHS) monodisperse neutralized aerosols, with selected particle size in the 0.03-0.40 μm range, was measured immediately prior to the start of the paraffin aerosol loading and at 1, 4, and 8 hr after the start of paraffin aerosol loading. Penetration through isopropanol-treated facepieces not oil paraffin loaded was also measured to evaluate facepiece behavior when electrostatic capture mechanisms are practically absent. During exposure to paraffin aerosol, DEHS penetration gradually increased for all aerosol sizes, and the most penetrating particle size (0.05 μm at the beginning of exposure) shifted slightly to larger diameters. After the isopropanol treatment, the higher penetration value was 0.30 μm. In addition to an increased penetration during paraffin loading at a given particle size, the relative degree of increase was greater as the particle size increased. Penetration value measured after 8 hr for 0.03-μm particles was on average 1.6 times the initial value, whereas it was about 8 times for 0.40-μm particles. This behavior, as well evidenced in the measurements of isopropanol-treated facepieces, can be attributed to the increasing action in particle capture of the electrostatic forces (Coulomb and polarization), which depend strictly on the diameter and electrical charge of neutralized aerosol particles. With reference to electrostatic filtering facepieces as personal protective equipment, results suggest the importance of complying with the manufacturer

  18. A single simple procedure for dewaxing, hydration and heat-induced epitope retrieval (HIER) for immunohistochemistry in formalin fixed paraffin-embedded tissue

    DEFF Research Database (Denmark)

    Paulsen, I M S; Dimke, H; Frische, S

    2015-01-01

    Heat-induced epitope retrieval (HIER) is widely used for immunohistochemistry on formalin fixed paraffin-embedded tissue and includes temperatures well above the melting point of paraffin. We therefore tested whether traditional xylene-based removal of paraffin is required on sections from paraff...... of dewaxing in xylene. In conclusion, the HIER procedure described and tested can be used as a single procedure enabling dewaxing, hydration and epitope retrieval for immunohistochemistry in formalin fixed paraffin-embedded tissue....

  19. Molecular diagnosis of skin infections using paraffin-embedded tissue - review and interdisciplinary consensus.

    Science.gov (United States)

    Sunderkötter, Cord; Becker, Karsten; Kutzner, Heinz; Meyer, Thomas; Blödorn-Schlicht, Norbert; Reischl, Udo; Nenoff, Pietro; Geißdörfer, Walter; Gräser, Yvonne; Herrmann, Mathias; Kühn, Joachim; Bogdan, Christian

    2018-02-01

    Nucleic acid amplification techniques (NATs), such as PCR, are highly sensitive and specific methods that have become valuable supplements to culture and serology in the diagnosis of infectious disorders. However, especially when using formalin-fixed and paraffin-embedded tissue, these techniques are associated with both false-negative and false-positive results, a pitfall that is frequently misjudged. Representatives of the German Society of Hygiene and Microbiology (DGHM) and the German Society of Dermatology (DDG) therefore set out to develop a consensus - in the form of a review article - on the appropriate indications for NATs using paraffin-embedded tissue, its contraindications, and the key points to be considered in the pre- and post-analytical phase. Given that fresh, naive tissue is preferably to be used in the workup of a suspected infection, PCR analysis on paraffin sections represents an exception. The latter may be considered if an infection is suspected at a later point in time and fresh tissue has not been preserved or can no longer be obtained. Potential indications include confirmation of histologically suspected infections with Leishmania spp., Bartonella spp., Rickettsia spp., or in case of ecthyma contagiosum. Infections with, for example, mycobacteria or RNA viruses, on the other hand, are not considered useful indications for NATs using paraffin sections. In order to avoid misinterpretation of test results, it is essential that laboratory reports on NATs using paraffin-embedded tissue contain information on the indication/diagnostic circumstances, the required and chosen pre-analytical steps, the limitations of the method, and on diagnostic alternatives. © 2018 Deutsche Dermatologische Gesellschaft (DDG). Published by John Wiley & Sons Ltd.

  20. Crust Structure Data of Seas Surrounding Turkey

    International Nuclear Information System (INIS)

    Maden, N.; Gelisli, K.

    2007-01-01

    Black Sea, Aegean, Mediterranean and Marmara Sea, which surround the Turkey, have not been examined with respect to the Geological, Geophysical and other natural sciences sufficiently. In fact, it is not attach importance the Turkish seas adequately and abandoned with respect to the scientific researches. The most important reason of this situation is the lack of the education of the Marine Sciences in the Turkish Universities. In this study, it is tried to construct a crustal structure data base of the surrounding seas of the Turkey by collecting crustal structure data sets done by different authors in different times so far. The data acquired in the base are collected from different data base sources by dragging. The Moho depth in the eastern and western basin of the Black sea is 22 km and 19 km, respectively. In the Marmara Sea the Moho depth is 24 km. The moho value in the southern Aegean is 20 km, in the northern Aegean the moho depth is 30 km. on the other hand, the moho depth value in the eastern and western basin of the Mediterranean Sea are 15-20 km and 25-30 km, respectively

  1. Efficient Cryosolid Positron Moderators

    Science.gov (United States)

    2012-08-01

    table layout Figure 21 shows the integration of the IR spectroscopy optics with the positron Moderation and Annihilation vacuum chambers on the...Characterization of Cryogenic Moderators The application of Matrix Isolation Spectroscopy (MIS) to characterizing cryogenic solid positron ...Matrix Isolation Spectroscopy capability into our Positron Moderation apparatus, which enables spectroscopic characterization of the cryogenic

  2. Comparison of SVM, RF and ELM on an Electronic Nose for the Intelligent Evaluation of Paraffin Samples

    Directory of Open Access Journals (Sweden)

    Hong Men

    2018-01-01

    Full Text Available Paraffin odor intensity is an important quality indicator when a paraffin inspection is performed. Currently, paraffin odor level assessment is mainly dependent on an artificial sensory evaluation. In this paper, we developed a paraffin odor analysis system to classify and grade four kinds of paraffin samples. The original feature set was optimized using Principal Component Analysis (PCA and Partial Least Squares (PLS. Support Vector Machine (SVM, Random Forest (RF, and Extreme Learning Machine (ELM were applied to three different feature data sets for classification and level assessment of paraffin. For classification, the model based on SVM, with an accuracy rate of 100%, was superior to that based on RF, with an accuracy rate of 98.33–100%, and ELM, with an accuracy rate of 98.01–100%. For level assessment, the R2 related to the training set was above 0.97 and the R2 related to the test set was above 0.87. Through comprehensive comparison, the generalization of the model based on ELM was superior to those based on SVM and RF. The scoring errors for the three models were 0.0016–0.3494, lower than the error of 0.5–1.0 measured by industry standard experts, meaning these methods have a higher prediction accuracy for scoring paraffin level.

  3. Opportunity's Surroundings on Sol 1798 (Polar)

    Science.gov (United States)

    2009-01-01

    NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this 180-degree view of the rover's surroundings during the 1,798th Martian day, or sol, of Opportunity's surface mission (Feb. 13, 2009). North is on top. This view is presented as a polar projection with geometric seam correction. The rover had driven 111 meters (364 feet) southward on the preceding sol. Tracks from that drive recede northward in this view. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock.

  4. Opportunity's Surroundings After Sol 1820 Drive (Polar)

    Science.gov (United States)

    2009-01-01

    NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,820th to 1,822nd Martian days, or sols, of Opportunity's surface mission (March 7 to 9, 2009). This view is presented as a polar projection with geometric seam correction. North is at the top. The rover had driven 20.6 meters toward the northwest on Sol 1820 before beginning to take the frames in this view. Tracks from that drive recede southwestward. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and small exposures of lighter-toned bedrock.

  5. Opportunity's Surroundings on Sol 1798 (Vertical)

    Science.gov (United States)

    2009-01-01

    NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this 180-degree view of the rover's surroundings during the 1,798th Martian day, or sol, of Opportunity's surface mission (Feb. 13, 2009). North is on top. This view is presented as a vertical projection with geometric seam correction. The rover had driven 111 meters (364 feet) southward on the preceding sol. Tracks from that drive recede northward in this view. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock.

  6. Opportunity's Surroundings on Sol 1687 (Vertical)

    Science.gov (United States)

    2009-01-01

    NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this 360-degree view of the rover's surroundings on the 1,687th Martian day, or sol, of its surface mission (Oct. 22, 2008). Opportunity had driven 133 meters (436 feet) that sol, crossing sand ripples up to about 10 centimeters (4 inches) tall. The tracks visible in the foreground are in the east-northeast direction. Opportunity's position on Sol 1687 was about 300 meters southwest of Victoria Crater. The rover was beginning a long trek toward a much larger crater, Endeavour, about 12 kilometers (7 miles) to the southeast. This view is presented as a vertical projection with geometric seam correction.

  7. Opportunity's Surroundings After Sol 1820 Drive (Vertical)

    Science.gov (United States)

    2009-01-01

    NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,820th to 1,822nd Martian days, or sols, of Opportunity's surface mission (March 7 to 9, 2009). This view is presented as a vertical projection with geometric seam correction. North is at the top. The rover had driven 20.6 meters toward the northwest on Sol 1820 before beginning to take the frames in this view. Tracks from that drive recede southwestward. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and small exposures of lighter-toned bedrock.

  8. Opportunity's Surroundings on Sol 1687 (Polar)

    Science.gov (United States)

    2009-01-01

    NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this 360-degree view of the rover's surroundings on the 1,687th Martian day, or sol, of its surface mission (Oct. 22, 2008). Opportunity had driven 133 meters (436 feet) that sol, crossing sand ripples up to about 10 centimeters (4 inches) tall. The tracks visible in the foreground are in the east-northeast direction. Opportunity's position on Sol 1687 was about 300 meters southwest of Victoria Crater. The rover was beginning a long trek toward a much larger crater, Endeavour, about 12 kilometers (7 miles) to the southeast. This view is presented as a polar projection with geometric seam correction.

  9. Opportunity's Surroundings After Sol 1820 Drive

    Science.gov (United States)

    2009-01-01

    NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,820th to 1,822nd Martian days, or sols, of Opportunity's surface mission (March 7 to 9, 2009). South is at the center; north at both ends. The rover had driven 20.6 meters toward the northwest on Sol 1820 before beginning to take the frames in this view. Tracks from that drive recede southwestward. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and small exposures of lighter-toned bedrock. This view is presented as a cylindrical projection with geometric seam correction.

  10. Towards Semantic Understanding of Surrounding Vehicular Maneuvers

    DEFF Research Database (Denmark)

    Kristoffersen, Miklas Strøm; Dueholm, Jacob Velling; Satzoda, Ravi K.

    2016-01-01

    This paper proposes the use of multiple low-cost visual sensors to obtain a surround view of the ego-vehicle for semantic understanding. A multi-perspective view will assist the analysis of naturalistic driving studies (NDS), by automating the task of data reduction of the observed sequences...... into events. A user-centric vision-based framework is presented using a vehicle detector and tracker in each separate perspective. Multi-perspective trajectories are estimated and analyzed to extract 14 different events, including potential dangerous behaviors such as overtakes and cut-ins. The system...... is tested on ten sequences of real-world data collected on U. S. highways. The results show the potential use of multiple low-cost visual sensors for semantic understanding around the ego-vehicle....

  11. Lovelock black holes surrounded by quintessence

    Energy Technology Data Exchange (ETDEWEB)

    Ghosh, Sushant G. [University of KwaZulu-Natal, Astrophysics and Cosmology Research Unit, School of Mathematics, Statistics and Computer Science, Durban (South Africa); Centre for Theoretical Physics, Multidisciplinary Centre for Advanced Research and Studies (MCARS), New Delhi (India); Maharaj, Sunil D.; Baboolal, Dharmanand; Lee, Tae-Hun [University of KwaZulu-Natal, Astrophysics and Cosmology Research Unit, School of Mathematics, Statistics and Computer Science, Durban (South Africa)

    2018-02-15

    Lovelock gravity consisting of the dimensionally continued Euler densities is a natural generalization of general relativity to higher dimensions such that equations of motion are still second order, and the theory is free of ghosts. A scalar field with a positive potential that yields an accelerating universe has been termed quintessence. We present exact black hole solutions in D-dimensional Lovelock gravity surrounded by quintessence matter and also perform a detailed thermodynamical study. Further, we find that the mass, entropy and temperature of the black hole are corrected due to the quintessence background. In particular, we find that a phase transition occurs with a divergence of the heat capacity at the critical horizon radius, and that specific heat becomes positive for r{sub h} < r{sub c} allowing the black hole to become thermodynamically stable. (orig.)

  12. Lovelock black holes surrounded by quintessence

    Science.gov (United States)

    Ghosh, Sushant G.; Maharaj, Sunil D.; Baboolal, Dharmanand; Lee, Tae-Hun

    2018-02-01

    Lovelock gravity consisting of the dimensionally continued Euler densities is a natural generalization of general relativity to higher dimensions such that equations of motion are still second order, and the theory is free of ghosts. A scalar field with a positive potential that yields an accelerating universe has been termed quintessence. We present exact black hole solutions in D-dimensional Lovelock gravity surrounded by quintessence matter and also perform a detailed thermodynamical study. Further, we find that the mass, entropy and temperature of the black hole are corrected due to the quintessence background. In particular, we find that a phase transition occurs with a divergence of the heat capacity at the critical horizon radius, and that specific heat becomes positive for r_h

  13. A RANDOMISED TRIAL OF LIQUID PARAFFIN VERSUS LACTULOSE IN THE TREATMENT OF CHRONIC FUNCTIONAL CONSTIPATION IN CHILDREN

    Directory of Open Access Journals (Sweden)

    F. Farahmand

    2007-07-01

    Full Text Available "nLiquid paraffin has been suggested as a good laxative comparing to lactulose as a treatment option in pediatric constipation. This study was performed to compare liquid paraffin with lactulose in pediatric constipation. A total of 247 patients (127 males and 120 females aged 2-12 years (mean 4.1 ± 2.7 years with chronic functional constipation were included in an 8 week, randomized, controlled trial. After faecal disimpaction, patients received oral liquid paraffin (1-2 cc/kg/day or lactulose (1-2 cc/kg/day. Primary outcome measures were: defecation and encopresis frequency per week and successful treatment after 8 weeks. Success was defined as a defecation frequency ≥ 3 per week and encopresis ≤ 1 every two weeks. Secondary outcome measures were side effects during 8 weeks of treatment. A significant increase in defecation frequency, liquid paraffin group, 3 pre, versus, 12 post treatment per week and lactulose group: 3 pre, versus 8 post, per week was found. A significant decrease in encopresis frequency, liquid paraffin: 10 pre, versus 1 post per week; lactulose: 9 pre, versus 3 post per week, was found in both groups. However success was significantly higher in the liquid paraffin group (85% compared with the lactulose group (29%. Liquid paraffin patients reported less abdominal pain, straining and pain at defecation than children using lactulose. Liquid paraffin is more effective than lactulose in the treatment of chronic functional constipation of childhood. It provided a higher success rate with fewer side effects. Liquid paraffin should be the laxative of first choice in childhood functional constipation.

  14. Insight into the influence of liquid paraffin for methanol synthesis on Cu(110) surface using continuum and atomistic models

    Energy Technology Data Exchange (ETDEWEB)

    Jiao, Wei-Hong [Key Laboratory of Coal Science and Technology of Ministry of Education and Shanxi Province, Taiyuan University of Technology, Taiyuan 030024, Shanxi (China); Liu, Shi-Zhong [Department of Chemistry, Stony Brook University, Stony Brook, NY 11794 (United States); Zuo, Zhi-Jun, E-mail: zuozhijun@tyut.edu.cn [Key Laboratory of Coal Science and Technology of Ministry of Education and Shanxi Province, Taiyuan University of Technology, Taiyuan 030024, Shanxi (China); Ren, Rui-Peng; Gao, Zhi-Hua [Key Laboratory of Coal Science and Technology of Ministry of Education and Shanxi Province, Taiyuan University of Technology, Taiyuan 030024, Shanxi (China); Huang, Wei, E-mail: huangwei@tyut.edu.cn [Key Laboratory of Coal Science and Technology of Ministry of Education and Shanxi Province, Taiyuan University of Technology, Taiyuan 030024, Shanxi (China)

    2016-11-30

    Highlights: • The influence of liquid paraffin is studied using continuum and atomistic models. • Liquid paraffin does not alter the reaction pathways of CO hydrogenation and WGS. • Liquid paraffin alters the reaction pathways of CO{sub 2} hydrogenation. - Abstract: Methanol synthesis from CO/CO{sub 2} hydrogenation and water-gas shift (WGS) reaction on Cu(110) in liquid paraffin and vacuum have been systematically researched with density functional theory calculation (DFT). For methanol synthesis from CO hydrogenation, the reaction pathways in liquid paraffin and vacuum are CO + H → HCO → H{sub 2}CO → H{sub 3}CO → H{sub 3}COH; in the case of WGS, the reaction pathways in liquid paraffin and vacuum are CO + 2H{sub 2}O → CO + 2OH + 2H → CO + H{sub 2}O + O + H{sub 2} → CO{sub 2} + H{sub 2}O + H{sub 2}; the reaction pathways of methanol synthesis from CO{sub 2} hydrogenation in liquid paraffin and vacuum are CO{sub 2} + H → HCOO → H{sub 2}COO → H{sub 2}CO → H{sub 3}CO → H{sub 3}COH and CO{sub 2} + H → HCOO → HCOOH → H{sub 2}COOH → H{sub 3}CO → H{sub 3}COH, respectively. The result shows that liquid paraffin does not affect the reaction mechanisms of methanol synthesis from CO and WGS, but it changes the reaction mechanisms of methanol synthesis from CO{sub 2} hydrogenation. Hirshfeld charge and the d-band centers indicate that the catalytic activity of Cu(110) in liquid paraffin is smaller than that in vacuum. Our results also show that it is necessary to consider both continuum and atomistic models in the slurry bed.

  15. Unperturbed moderator brightness in pulsed neutron sources

    International Nuclear Information System (INIS)

    Batkov, K.; Takibayev, A.; Zanini, L.; Mezei, F.

    2013-01-01

    The unperturbed neutron brightness of a moderator can be defined from the number of neutrons leaving the surface of a moderator completely surrounded by a reflector. Without openings for beam extraction, it is the maximum brightness that can be theoretically achieved in a moderator. The unperturbed brightness of a cylindrical cold moderator filled with pure para-H 2 was calculated using MCNPX; the moderator dimensions were optimised, for a fixed target and reflector geometry corresponding to the present concept for the ESS spallation source. This quantity does not depend on openings for beam extraction and therefore can be used for a first-round optimisation of a moderator, before effects due to beam openings are considered. We find that such an optimisation yields to a factor of 2 increase with respect to a conventional volume moderator, large enough to accommodate a viewed surface of 12×12 cm 2 : the unperturbed neutron brightness is maximum for a disc-shaped moderator of 15 cm diameter, 1.4 cm height. The reasons for this increase can be related to the properties of the scattering cross-section of para-H 2 , to the added reflector around the exit surface in the case of a compact moderator, and to a directionality effect. This large optimisation gain in the unperturbed brightness hints towards similar potentials for the perturbed neutron brightness, in particular in conjunction with advancing the optical quality of neutron delivery from the moderator to the sample, where by Liouville theorem the brightness is conserved over the beam trajectory, except for absorption and similar type losses

  16. Study of the composition of impurities in paraffins, which have been removed at different stages of the carbamide deparaffinization process

    Energy Technology Data Exchange (ETDEWEB)

    Dorodnova, V.S.; Martirosov, R.A.; Martynenko, A.G.; Pereverzev, A.N.

    1980-01-01

    Results of the study on the composition of impurities in paraffin raw material, which has been removed from different stages of a deparaffinization unit are presented. It is shown that by using the method of chromatographic partitioning of paraffins during rinsing of the system basically monocyclic aromatics are removed, and the content of polycyclic aromatics and resins shows practically no change. A separation temperature of the system of 93-95/sup 0/ is recommended as optimum for existing G-64 commercial units. The content of residual paraffin in this case in the carbamide is about 1%.

  17. Proteome stability analysis of snap frozen, RNAlater preserved, and formalin-fixed paraffin-embedded human colon mucosal biopsies

    DEFF Research Database (Denmark)

    Bjerg Bennike, Tue; Kastaniegaard, Kenneth; Padurariu, Simona

    2016-01-01

    Large repositories of well characterized RNAlater preserved samples and formalin-fixed, paraffin-embedded samples have been generated worldwide. However, the impact on the proteome of the preservation methods remain poorly described. Therefore, we analyzed the impact on the proteome of preserving...... samples in RNAlater, and by formalin-fixation, paraffin-embedding on human soft tissue, using directly frozen samples as a control ("Comparing the proteome of snap frozen, RNAlater preserved, and formalin-fixed paraffin-embedded human tissue samples" [1]). We here report the data from the analysis...

  18. Radio-induced oxidation of n-paraffins for obtaining biodegradable detergents; L'oxydation radioinduite des n-paraffines pour l'obtention de detergents biodegradables

    Energy Technology Data Exchange (ETDEWEB)

    Puig, J R; Laizier, J; Blin, M F; Marchand, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1968-07-01

    N-paraffins oxidation is a feasible way to obtain biodegradable detergents. This reaction can be radio-initiated and it proceeds by a branched chain mechanism, with an induction pseudo-period. A suitable analysis of the reaction is allowed by the semi-logarithmic plot of its evolution. Influence of the different parameters of the reaction is studied, results show that the use of radiation for initiating the reaction is of no economical interest. (authors) [French] L'oxydation des n-paraffines est une voie possible d'obtention des detergents biodegradables. Cette reaction, qui peut etre radioinitiee, procede d'un mecanisme en chaine branchee et presente une pseudoperiode d'induction. La representation semi-logarithmique de l'avancement de la reaction permet une analyse commode de celle-ci. L'influence des differents parametres est etudiee. Les resultats montrent que l'utilisation du rayonnement pour l'initiation de la reaction est sans interet economique. (auteurs)

  19. Composite phase change materials prepared by encapsuling paraffin in PVC macrocapsules

    International Nuclear Information System (INIS)

    Chen, Yingbo; Zhang, Shifeng; Zhang, Qi; Chen, Yusheng; Zhang, Yufeng

    2014-01-01

    Highlights: • PVC macrocapsules coated with SiO 2 were synthesized. • Paraffin was encapsuled in the capsules. • The composite PCM has high heat capacity. • The composite PCM has no surpercooling. - Abstract: A novel phase change material capsules with SiO 2 in their surface was prepared by absorbing paraffin into PVC hollow capsules and by the polycondensation reaction of TEOS in different conditions. X-ray photoelectron spectroscopy (XPS) analysis and scanning electronic microscope (SEM) were used to determine chemical composition and microstructure of the composite capsules, respectively. Enthalpy capacity and thermal stability of the composite capsules are systematically characterized by using differential scanning calorimeter (DSC), thermogravimetric analyzer (TGA) and thermocycling tests. The composite has high heat capacity with good stability and absence of supercooling phenomena

  20. The effect of temperature on the mechanical aspects of rigor mortis in a liquid paraffin model.

    Science.gov (United States)

    Ozawa, Masayoshi; Iwadate, Kimiharu; Matsumoto, Sari; Asakura, Kumiko; Ochiai, Eriko; Maebashi, Kyoko

    2013-11-01

    Rigor mortis is an important phenomenon to estimate the postmortem interval in forensic medicine. Rigor mortis is affected by temperature. We measured stiffness of rat muscles using a liquid paraffin model to monitor the mechanical aspects of rigor mortis at five temperatures (37, 25, 10, 5 and 0°C). At 37, 25 and 10°C, the progression of stiffness was slower in cooler conditions. At 5 and 0°C, the muscle stiffness increased immediately after the muscles were soaked in cooled liquid paraffin and then muscles gradually became rigid without going through a relaxed state. This phenomenon suggests that it is important to be careful when estimating the postmortem interval in cold seasons. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

  1. The Effect of Paraffin Wax to Properties of Radiation Vulcanization Natural Rubber Latex (RVNRL)

    International Nuclear Information System (INIS)

    Mohd Noorwadi Mat Lazim; Sofian Ibrahim; Muhammad Saiful Omar

    2015-01-01

    Dipping factories often encounter a serious problem with high tackiness of the finish products during storage. The tackiness effect can be lead to rejection of products. This tackiness effect of natural (NR) rubber film originates in the free rubber chain ends at the surface of the film. The tackiness is not depends on the degree of crosslinking (vulcanization), since radiation itself unable to reduce the tackiness effect. The RVNRL requires addition of additive or anti-tack agent into formulation to reduce tackiness effect. In this experiment, paraffin wax manufactured by Emulco Sdn Bhd under the trade name Aquawax 48 was added into RVNRL formulation as anti-tack and the effect of paraffin wax to physical and mechanical properties of RVNRL was study. (author)

  2. Advantages of infrared transflection micro spectroscopy and paraffin-embedded sample preparation for biological studies

    Science.gov (United States)

    Yao, Jie; Li, Qian; Zhou, Bo; Wang, Dan; Wu, Rie

    2018-04-01

    Fourier-Transform Infrared micro-spectroscopy is an excellent method for biological analyses. In this paper, series metal coating films on ITO glass were prepared by the electrochemical method and the different thicknesses of paraffin embedding rat's brain tissue on the substrates were studied by IR micro-spetroscopy in attenuated total reflection (ATR) mode and transflection mode respectively. The Co-Ni-Cu alloy coating film with low cost is good reflection substrates for the IR analysis. The infrared microscopic transflection mode needs not to touch the sample at all and can get the IR spectra with higher signal to noise ratios. The Paraffin-embedding method allows tissues to be stored for a long time for re-analysis to ensure the traceability of the sample. Also it isolates the sample from the metal and avoids the interaction of biological tissue with the metals. The best thickness of the tissues is 4 μm.

  3. Penis deformity after intra-urethral liquid paraffin administration in a young male: a case report.

    Science.gov (United States)

    Kokkonouzis, Ioannis; Antoniou, Georgios; Droulias, Athanasios

    2008-10-07

    Self-induced injections of liquid substances mainly for penis enlargement is a well-documented but still rather uncommon practice in the western world. Herein we present the case of a 30-year-old male who self-inflicted, twice in a six-month-period, intra-urethral liquid paraffin and tied up his penis with a cord in order to achieve both enlargement and elongation. He arrived in our emergency department suffering from suprapubic pain; physical examination revealed a rather unique deformity of the penis. He finally refused any treatment and absconded. Side effects after paraffin administration are various and sometimes severe. Most of the times surgical treatment is needed and radical excision together with follow-up seems the best modality. Such practices emphasize on the public's misbelieves and that some aspects of sexual medicine are yet covered with the veil of misconception.

  4. Opportunity's Surroundings on Sol 1798 (Stereo)

    Science.gov (United States)

    2009-01-01

    [figure removed for brevity, see original site] Left-eye view of a color stereo pair for PIA11850 [figure removed for brevity, see original site] Right-eye view of a color stereo pair for PIA11850 NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this stereo 180-degree view of the rover's surroundings during the 1,798th Martian day, or sol, of Opportunity's surface mission (Feb. 13, 2009). North is on top. This view combines images from the left-eye and right-eye sides of the navigation camera. It appears three-dimensional when viewed through red-blue glasses with the red lens on the left. The rover had driven 111 meters (364 feet) southward on the preceding sol. Tracks from that drive recede northward in this view. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock. This view is presented as a cylindrical-perspective projection with geometric seam correction.

  5. Opportunity's Surroundings on Sol 1818 (Stereo)

    Science.gov (United States)

    2009-01-01

    [figure removed for brevity, see original site] Left-eye view of a color stereo pair for PIA11846 [figure removed for brevity, see original site] Right-eye view of a color stereo pair for PIA11846 NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,818th Martian day, or sol, of Opportunity's surface mission (March 5, 2009). South is at the center; north at both ends. This view combines images from the left-eye and right-eye sides of the navigation camera. It appears three-dimensional when viewed through red-blue glasses with the red lens on the left. The rover had driven 80.3 meters (263 feet) southward earlier on that sol. Tracks from the drive recede northward in this view. The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and lighter-toned bedrock. This view is presented as a cylindrical-perspective projection with geometric seam correction.

  6. Opportunity's Surroundings on Sol 1687 (Stereo)

    Science.gov (United States)

    2009-01-01

    [figure removed for brevity, see original site] Left-eye view of a color stereo pair for PIA11739 [figure removed for brevity, see original site] Right-eye view of a color stereo pair for PIA11739 NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this stereo, 360-degree view of the rover's surroundings on the 1,687th Martian day, or sol, of its surface mission (Oct. 22, 2008). The view appears three-dimensional when viewed through red-blue glasses. Opportunity had driven 133 meters (436 feet) that sol, crossing sand ripples up to about 10 centimeters (4 inches) tall. The tracks visible in the foreground are in the east-northeast direction. Opportunity's position on Sol 1687 was about 300 meters southwest of Victoria Crater. The rover was beginning a long trek toward a much larger crater, Endeavour, about 12 kilometers (7 miles) to the southeast. This panorama combines right-eye and left-eye views presented as cylindrical-perspective projections with geometric seam correction.

  7. Opportunity's Surroundings After Sol 1820 Drive (Stereo)

    Science.gov (United States)

    2009-01-01

    [figure removed for brevity, see original site] Left-eye view of a color stereo pair for PIA11841 [figure removed for brevity, see original site] Right-eye view of a color stereo pair for PIA11841 NASA's Mars Exploration Rover Opportunity used its navigation camera to take the images combined into this full-circle view of the rover's surroundings during the 1,820th to 1,822nd Martian days, or sols, of Opportunity's surface mission (March 7 to 9, 2009). This view combines images from the left-eye and right-eye sides of the navigation camera. It appears three-dimensional when viewed through red-blue glasses with the red lens on the left. The rover had driven 20.6 meters toward the northwest on Sol 1820 before beginning to take the frames in this view. Tracks from that drive recede southwestward. For scale, the distance between the parallel wheel tracks is about 1 meter (about 40 inches). The terrain in this portion of Mars' Meridiani Planum region includes dark-toned sand ripples and small exposures of lighter-toned bedrock. This view is presented as a cylindrical-perspective projection with geometric seam correction.

  8. The lithosphere-asthenosphere: Italy and surroundings

    International Nuclear Information System (INIS)

    Panza, G.F.; Aoudia, A.; Pontevivo, A.; Chimera, G.; Raykova, R.

    2003-02-01

    The velocity-depth distribution of the lithosphere-asthenosphere in the Italian region and surroundings is imaged, with a lateral resolution of about 100 km, by surface wave velocity tomography and non-linear inversion. Maps of the Moho depth, of the thickness of the lithosphere and of the shear-wave velocities, down to depths of 200 km and more, are constructed. A mantle wedge, identified in the uppermost mantle along the Apennines and the Calabrian Arc, underlies the principal recent volcanoes, and partial melting can be relevant in this part of the uppermost mantle. In Calabria a lithospheric doubling is seen, in connection with the subduction of the Ionian lithosphere. The asthenosphere is shallow in the Southern Tyrrhenian Sea. High velocity bodies, cutting the asthenosphere, outline the Adria-lonian subduction in the Tyrrhenian Sea and the deep-reaching lithospheric root in the Western Alps. Less deep lithospheric roots are seen in the Central Apennines. The lithosphere-asthenosphere properties delineate a differentiation between the northern and the southern sectors of the Adriatic Sea, likely attesting the fragmentation of Adria. (author)

  9. The lithosphere-asthenosphere Italy and surroundings

    CERN Document Server

    Panza, G F; Chimera, G; Pontevivo, A; Raykova, R

    2003-01-01

    The velocity-depth distribution of the lithosphere-asthenosphere in the Italian region and surroundings is imaged, with a lateral resolution of about 100 km, by surface wave velocity tomography and non-linear inversion. Maps of the Moho depth, of the thickness of the lithosphere and of the shear-wave velocities, down to depths of 200 km and more, are constructed. A mantle wedge, identified in the uppermost mantle along the Apennines and the Calabrian Arc, underlies the principal recent volcanoes, and partial melting can be relevant in this part of the uppermost mantle. In Calabria a lithospheric doubling is seen, in connection with the subduction of the Ionian lithosphere. The asthenosphere is shallow in the Southern Tyrrhenian Sea. High velocity bodies, cutting the asthenosphere, outline the Adria-lonian subduction in the Tyrrhenian Sea and the deep-reaching lithospheric root in the Western Alps. Less deep lithospheric roots are seen in the Central Apennines. The lithosphere-asthenosphere properties delineat...

  10. INTERSTELLAR MAGNETIC FIELD SURROUNDING THE HELIOPAUSE

    International Nuclear Information System (INIS)

    Whang, Y. C.

    2010-01-01

    This paper presents a three-dimensional analytical solution, in the limit of very low plasma β-ratio, for the distortion of the interstellar magnetic field surrounding the heliopause. The solution is obtained using a line dipole method that is the integration of point dipole along a semi-infinite line; it represents the magnetic field caused by the presence of the heliopause. The solution allows the variation of the undisturbed magnetic field at any inclination angle. The heliosphere is considered as having blunt-nosed geometry on the upwind side and it asymptotically approaches a cylindrical geometry having an open exit for the continuous outflow of the solar wind on the downwind side. The heliopause is treated as a magnetohydrodynamic tangential discontinuity; the interstellar magnetic field lines at the boundary are tangential to the heliopause. The interstellar magnetic field is substantially distorted due to the presence of the heliopause. The solution shows the draping of the field lines around the heliopause. The magnetic field strength varies substantially near the surface of the heliopause. The effect on the magnetic field due to the presence of the heliopause penetrates very deep into the interstellar space; the depth of penetration is of the same order of magnitude as the scale length of the heliosphere.

  11. Radio-induced oxidation of n-paraffins for obtaining biodegradable detergents

    International Nuclear Information System (INIS)

    Puig, J.R.; Laizier, J.; Blin, M.F.; Marchand, J.

    1968-01-01

    N-paraffins oxidation is a feasible way to obtain biodegradable detergents. This reaction can be radio-initiated and it proceeds by a branched chain mechanism, with an induction pseudo-period. A suitable analysis of the reaction is allowed by the semi-logarithmic plot of its evolution. Influence of the different parameters of the reaction is studied, results show that the use of radiation for initiating the reaction is of no economical interest. (authors) [fr

  12. Empirical equations for viscosity and specific heat capacity determination of paraffin PCM and fatty acid PCM

    Science.gov (United States)

    Barreneche, C.; Ferrer, G.; Palacios, A.; Solé, A.; Inés Fernández, A.; Cabeza, L. F.

    2017-10-01

    Phase change materials (PCM) used in thermal energy storage (TES) systems have been presented, over recent years, as one of the most effective options in energy storage. Paraffin and fatty acids are some of the most used PCM in TES systems, as they have high phase change enthalpy and in addition they do not present subcooling nor hysteresis and have proper cycling stability. The simulations and design of TES systems require the knowledge of the thermophysical properties of PCM. Thermal conductivity, viscosity, specific heat capacity (Cp) can be experimentally determined, but these are material and time consuming tasks. To avoid or to reduce them, and to have reliable data without the need of experimentation, thermal properties can be calculated by empirical equations. In this study, five different equations are given to calculate the viscosity and specific heat capacity of fatty acid PCM and paraffin PCM. Two of these equations concern, respectively, the empirical calculation of the viscosity and liquid Cp of the whole paraffin PCM family, while the other three equations presented are for the corresponding calculation of viscosity, solid Cp, liquid Cp of the whole fatty acid family of PCM. Therefore, this study summarize the work performed to obtain the main empirical equations to measure the above mentioned properties for whole fatty acid PCM family and whole paraffin PCM family. Moreover, empirical equations have been obtained to calculate these properties for other materials of these PCM groups and these empirical equations can be extrapolated for PCM with higher or lower phase change temperatures within a lower relative error 4%.

  13. Endosulfan, pentachlorobenzene and short-chain chlorinated paraffins in background soils from Western Europe

    OpenAIRE

    Halse, Anne Karine; Schlabach, Martin; Schuster, Jasmin K; Jones, Kevin C; Steinnes, Eiliv; Breivik, Knut

    2015-01-01

    Soils are major reservoirs for many persistent organic pollutants (POPs). In this study, “newly” regulated POPs i.e. sum endosulfans (a-endosulfan, b-endosulfan, endosulfan sulfate), pentachlorobenzene (PeCB), and short-chain chlorinated paraffins (SCCPs) were determined in background samples from woodland (WL) and grassland (GL) surface soil, collected along an existing latitudinal UK-Norway transect. Statistical analysis, complemented with plots showing the predicted equilibrium distributio...

  14. Determination of Short-Chain Chlorinated Paraffins by Carbon Skeleton Gas Chromatography

    OpenAIRE

    PELLIZZATO FRANCESCA; RICCI MARINA; HELD ANDREA; EMONS HENDRIK

    2008-01-01

    Short-Chain Chlorinated Paraffins (SCCPs) are highly complex technical mixtures of polychlorinated n-alkanes with a chlorination degree between 50 and 70 % by mass, and a linear carbon chain length from C10 to C13, constituted by thousands of homologues, diastereomers and enantiomers. They have been used in many different applications, such as extreme pressure additives in lubricants and cutting fluids, plasticizers in PVC, and flame retardants in paints, adhesives and sealants. SCCPs are tox...

  15. Experimental evaluation of hybrid propulsion rocket engine operating with paraffin fuel grain and gaseous oxygen

    OpenAIRE

    Genivaldo Pimenta dos Santos

    2014-01-01

    In the last decade the hybrid propulsion has been considering as a viable alternative of chemical energy conversion stored in propellants into kinetic energy. This energy is applied in propulsive systems of manned platforms, maneuvering procedures and even in the repositioning process of micro satellites. It presents attractive features and good balance between performance and environmental impact. Paraffin based grains are the hybrid solid fuels appointed as polymeric fuel substitute. The li...

  16. Technical tutorial: How to pack a nose with bismuth iodoform paraffin paste gauze safely and effectively.

    Science.gov (United States)

    Amen, F; Pace-Balzan, A

    2009-01-01

    The current primary treatment for epistaxis in accident and emergency departments is the insertion of Merocel packs. If these are properly inserted, but fail to control bleeding, it is necessary to insert a bismuth iodoform paraffin paste (BIPP) pack. A BIPP pack, when properly inserted, has the potential to stop most bleeds, but books and journals suggest a method of insertion that limits its effectiveness. A safer and more effective way of packing a nose with BIPP than the traditional method is described.

  17. KH in Paraffin - KH(P): A Useful Base for Organic Synthesis

    Science.gov (United States)

    Taber, Douglass F.; Nelson, Christopher G.

    2011-01-01

    The preparation of KH as a one:one homogenate with paraffin, termed KH(P), is reported. KH(P), a solid at room temperature, is stable without special handling. On suspension in THF with a phosphonium salt, KH(P) rapidly generates the ylide. Wittig condensation with aromatic, aliphatic and α, β-unsaturated aldehydes proceeds with high Z-selectivity. KH(P) should be a generally useful base for organic synthesis. PMID:17081034

  18. Experimental analysis, modeling and simulation of a solar energy accumulator with paraffin wax as PCM

    International Nuclear Information System (INIS)

    Reyes, A.; Henríquez-Vargas, L.; Aravena, R.; Sepúlveda, F.

    2015-01-01

    Highlights: • Enhancement of paraffin wax thermal conductivity using soft drink can stripes. • Thermal analysis and simulations results agree well with experimental data. • Increase in accumulator thermal efficiencies through addition of external aluminum stripes. • Proposed accumulator allows up to 13,000 kJ of energy storage. - Abstract: Soft drink cans filled with paraffin wax mixed with 7.5% aluminum stripes, obtained from disposable cans, doubled the thermal conductivity of cans filled only with paraffin wax. Promising results obtained in a prototype heat exchanger encouraged the construction of this unit 6 times bigger. We experimentally evaluated and model a heat exchanger for solar energy accumulation, composed by 300 disposable soft drink cans filled with a total of 59.25 kg of paraffin wax mixed with 7.5% aluminum stripes. The effect of adding 2.75 kg of aluminum fins for enhancing heat transfer from the outer surface of the cans to the circulant air was experimentally analyzed. In sunny days, the wax melted completely in about 4 h. The accumulated energy in form of latent heat (about 13,000 kJ) allowed to increase the temperature of 0.040 kg/s of circulant air in at least 20 °C during a period of 2.5 h. For an air mass rate of 0.018 kg/s the period was extended practically to 5 h. The accumulator thermal analysis was presented and a subsequent numerical simulation with Matlab was performed to compare with the experimental results obtaining good agreement specially for higher air mass flow rates. The low cost accumulator presented is of simple construction and will allow extended use of solar energy for applications such as drying processes or household calefaction system.

  19. Hybrid optical pumping of K and Rb atoms in a paraffin coated vapor cell

    Science.gov (United States)

    Li, Wenhao; Peng, Xiang; Budker, Dmitry; Wickenbrock, Arne; Pang, Bo; Zhang, Rui; Guo, Hong

    2017-10-01

    Dynamic hybrid optical pumping effects with a radio-frequency-field-driven nonlinear magneto-optical rotation (RF NMOR) scheme are studied in a dual-species paraffin coated vapor cell. By pumping K atoms and probing $^{87}$Rb atoms, we achieve an intrinsic magnetic resonance linewidth of 3 Hz and the observed resonance is immune to power broadening and light-shift effects. Such operation scheme shows favorable prospects for atomic magnetometry applications.

  20. Methods for separating boron from borated paraffin wax and its determination by ion chromatography

    International Nuclear Information System (INIS)

    Jeyakumar, S.

    2015-01-01

    Boron compounds are found to be useful in shielding against high-energy neutrons. In radiotherapy treatments, in order to protect occupational workers and patients from the undesirable neutron and gamma doses, paraffin wax containing B 4 C/boric acid is used. Low-level borate wastes generated from the nuclear power plants have been immobilized with paraffin wax using a concentrate waste drying system (CWDS). Borated paraffin waxes are prepared by mixing calculated amounts of either boric acid or boron carbide with the molten wax. This necessitates the determination of boron at different locations in order to check the homogeneous distribution of B over the borated wax. The determination of boron in nuclear materials is inevitable due to its high neutron absorption cross section. For the determination of boron in borated waxes, not many methods have been reported. A method based on the pyrohydrolysis extraction of boron and its quantification with ion chromatography was proposed for paraffin waxes borated with H 3 BO 3 and B 4 C. The B 4 C optimum pyrohydrolysis conditions were identified. Wax samples were mixed with U 3 O 8 , which prevents the sample from flare up, and also accelerates the extraction of boron. Pyrohydrolysis was carried out with moist O 2 at 950℃ for 60 and 90 min for wax with H 3 BO 3 and wax with B 4 C, respectively. Two simple methods of separation based on alkali extraction and melting wax in alkali were also developed exclusively for wax with H 3 BO 3 . In all the separations, the recovery of B was above 98%. During IC separation, B was separated as boron-mannitol anion complex. Linear calibration was obtained between 0.1 and 50 ppm of B, and LOD was calculated as 5 ppb (S/N=3). The reproducibility was better than 5% (RSD)

  1. Diagnosis of lymphoma in paraffin wax sections by nested PCR and immunohistochemistry.

    OpenAIRE

    Kitamura, Y; Nanba, E; Inui, S; Tanigawa, T; Ichihara, K

    1996-01-01

    AIMS: To investigate whether nested polymerase chain reaction (PCR) and immunohistochemistry can be used to diagnose malignant lymphoma. METHODS: Paraffin wax embedded tissue sections from 31 patients with malignant lymphoma were analysed by nested PCR and immunohistochemistry using standard protocols. RESULTS: Nested PCR amplification of 1 pg DNA confirmed monoclonality in B cell lymphoma; PCR amplification of 10 pg DNA confirmed monoclonality in T cell lymphoma. Twenty seven (87%) samples w...

  2. Grooved cold moderator tests

    International Nuclear Information System (INIS)

    Inoue, K.; Kiyanagi, Y.; Iwasa, H.; Watanabe, N.; Ikeda, S.; Carpenter, J.M.; Ishikawa, Y.

    1983-01-01

    We performed some grooved cold moderator experiments for methane at 20 K by using the Hokkaido University linac to obtain information to be used in the planning of the KENS-I' project. Cold neutron gains, spatial distribution of emitted beams and time distribution of the neutrons in the grooved cold moderator were measured. Furthermore, we assessed the effects of the grooved cold moderator on the performances of the spectrometers presently installed at the KENS-I cold source. We concluded that the grooved cold moderator benefited appreciably the performances of the spectrometers

  3. Optimization of Glial Fibrillary Acidic Protein Immunoreactivity in Formalin-fixed, Paraffin-Embedded Guinea Pig Brain Sections

    Science.gov (United States)

    2003-09-01

    fixed, paraffin-embedded guinea pig brain sections using a variety of commercially available GFAP antibody clones. Of the 7 clones tested for cross...determining neuropathological consequences in the guinea pig following exposure to chemical warfare nerve agent.

  4. Ultra-Tuning of the Rare-Earth fcu-MOF Aperture Size for Selective Molecular Exclusion of Branched Paraffins

    KAUST Repository

    Assen, Ayalew Hussen Assen

    2015-10-02

    Using isoreticular chemistry allows the design and construction of a new rare-earth metal (RE) fcu-MOF with a suitable aperture size for practical steric adsorptive separations. The judicious choice of a relatively short organic building block, namely fumarate, to bridge the 12-connected RE hexanuclear clusters has afforded the contraction of the well-defined RE-fcu-MOF triangular window aperture, the sole access to the two interconnected octahedral and tetrahedral cages. The newly constructed RE (Y and Tb) fcu-MOF analogues display unprecedented total exclusion of branched paraffins from normal paraffins. The resultant window aperture size of about 4.7 Å, regarded as a sorbate-size cut-off, enabled a complete sieving of branched paraffins from normal paraffins. The results are supported by collective single gas and mixed gas/vapor adsorption and calorimetric studies.

  5. Ultra-Tuning of the Rare-Earth fcu-MOF Aperture Size for Selective Molecular Exclusion of Branched Paraffins.

    Science.gov (United States)

    Assen, Ayalew H; Belmabkhout, Youssef; Adil, Karim; Bhatt, Prashant M; Xue, Dong-Xu; Jiang, Hao; Eddaoudi, Mohamed

    2015-11-23

    Using isoreticular chemistry allows the design and construction of a new rare-earth metal (RE) fcu-MOF with a suitable aperture size for practical steric adsorptive separations. The judicious choice of a relatively short organic building block, namely fumarate, to bridge the 12-connected RE hexanuclear clusters has afforded the contraction of the well-defined RE-fcu-MOF triangular window aperture, the sole access to the two interconnected octahedral and tetrahedral cages. The newly constructed RE (Y(3+) and Tb(3+)) fcu-MOF analogues display unprecedented total exclusion of branched paraffins from normal paraffins. The resultant window aperture size of about 4.7 Å, regarded as a sorbate-size cut-off, enabled a complete sieving of branched paraffins from normal paraffins. The results are supported by collective single gas and mixed gas/vapor adsorption and calorimetric studies. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Protein extraction from methanol fixed paraffin embedded tissue blocks: A new possibility using cell blocks

    Science.gov (United States)

    Kokkat, Theresa J.; McGarvey, Diane; Patel, Miral S.; Tieniber, Andrew D.; LiVolsi, Virginia A.; Baloch, Zubair W.

    2013-01-01

    Background: Methanol fixed and paraffin embedded (MFPE) cellblocks are an essential cytology preparation. However, MFPE cellblocks often contain limited material and their relatively small size has caused them to be overlooked in biomarker discovery. Advances in the field of molecular biotechnology have made it possible to extract proteins from formalin fixed and paraffin embedded (FFPE) tissue blocks. In contrast, there are no established methods for extracting proteins from MFPE cellblocks. We investigated commonly available CHAPS (3-[(3-cholamidopropyl) dimethylammonio]-1-propanesulfonate) buffer, as well as two commercially available Qiagen® kits and compared their effectiveness on MFPE tissue for protein yields. Materials and Methods: MFPE blocks were made by Cellient™ automated system using human tissue specimens from normal and malignant specimens collected in ThinPrep™ Vials. Protein was extracted from Cellient-methanol fixed and paraffin embedded blocks with CHAPS buffer method as well as FFPE and Mammalian Qiagen® kits. Results: Comparison of protein yields demonstrated the effectiveness of various protein extraction methods on MFPE cellblocks. Conclusion: In the current era of minimally invasive techniques to obtain minimal amount of tissue for diagnostic and prognostic purposes, the use of commercial and lab made buffer on low weight MFPE scrapings obtained by Cellient® processor opens new possibilities for protein biomarker research. PMID:24403950

  7. UV irradiation-initiated MMA polymerization to prepare microcapsules containing phase change paraffin

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Sude; Song, Guolin; Li, Wei; Fan, Pengfei; Tang, Guoyi [Institute of Advanced Materials, Graduated School at Shenzhen, Tsinghua University, Shenzhen 518055 (China)

    2010-10-15

    Microencapsulated phase change material (MEPCM), paraffin, with polymethylmethacrylate shell was prepared by introducing UV irradiation to an O/W emulsion polymerization for approximately 30 min under constant stirring. The results of differential scanning calorimetry analyses indicate that the latent heat and the content of paraffin of microcapsules are 101 J g{sup -1} and 61.2 wt%, respectively. The phase transition temperature of MEPCM ranges from 24 to 33 C. The MEPCM was characterized using scanning electron microscopy and Fourier transform infrared spectroscopy. Thermal gravimetric analysis results show that the MEPCM is degraded into two distinguishable steps. Accelerated thermal cycling tests also indicate that the MEPCM displays a good thermal reliability. Gypsum boards composed of as-prepared MEPCM show a good temperature-regulated property. Based on all these results, it can be concluded that the microencapsulated paraffin as MEPCMs have good potential for thermal energy storage purposes such as phase change material slurries, solar space heating applications, textiles and building materials. (author)

  8. Experimental research in the phase change materials based on paraffin and expanded perlite

    Science.gov (United States)

    Jiesheng, Liu; Faping, Li; Xiaoqiang, Gong; Rongtang, Zhang

    2018-06-01

    In this study, paraffin (PA)/expanded perlite (EP) form-stable phase change material (PCM) was first fabricated using the direct impregnation method without vacuum treatment. Absorptive capacity results showed that the PA/EP composite can obtain good absorptive capacity with the temperature 80 °C and the time 2 h. Compared with the water absorption of EP, the decrease in the water absorption of PA/EP form-stable proved that the absorption of PA into porous EP has been carried out successfully. Scanning electron microscope (SEM) and Fourier transform infrared (FT-IR) results show that paraffin can be well impregnated into EP pores and has good compatibility with it. Differential scanning calorimetry (DSC) results reveal that paraffin/EP composite PCM has melting temperature and latent heat of 53.6 °C and 91.3 J/g, respectively. The durability cycles results suggest that form-stable PA/EP PCM shows good durability.

  9. A SIMPLE PARAFFIN EMBEDDED PROTOCOL FOR FISH EGG, EMBRYO, AND LARVAE

    Directory of Open Access Journals (Sweden)

    Gratiana Eka Wijayanti

    2017-06-01

    Full Text Available This paper describes a simple protocol of paraffin-embedded histological section for fish eggs, embryo and larvae of the hard-lipped barb and the giant gourami. The specimens were fixed in Bouin solution, washed in 70% ethanol, then were dehydrated in a series of ethanol solution of increasing concentration until absolute ethanol was reached. The specimens were cleared in graded xylene and were infiltrated with liquid paraffin then were embedded in pure paraffin. Upon sectioning, at 4–5 µm thick the specimens were attached to the gelatin-coated glass slide and let to dry at room temperature or 37°C overnight. The specimens were deparaffinized in xylene, rehydrated then were stained with hematoxylin and eosin. After being dehydrated in graded ethanol, the specimens were cleared in xylene and were mounted with an organic mounting agent. Any step in preparing histological section including samples collection, fixation, dehydration, infiltration and embedding might contribute to the quality of histological features. A proper knowledge of the tissues beeing processed, fixative solution and the histological techniques is essential to gain good results. Bouin fixative is preferable to fix fish larvae and produce a good histological feature. Decalcification is necessary to produce a good histological section on the specimens containing bone.

  10. Synthesis, characterization and thermal properties of paraffin microcapsules modified with nano-Al2O3

    International Nuclear Information System (INIS)

    Jiang, Xiang; Luo, Ruilian; Peng, Feifei; Fang, Yutang; Akiyama, Tomohiro; Wang, Shuangfeng

    2015-01-01

    Highlights: • Novel MEPCM modified with nano-Al 2 O 3 was prepared via emulsion polymerization. • The paraffin microcapsules presented a well-defined microstructure. • The composite achieved high encapsulation efficiency. • The thermal conductivity of MEPCM was enhanced due to the nano-Al 2 O 3 particles. - Abstract: A sort of new microencapsulated phase change materials (MEPCM) based on paraffin wax core and poly(methyl methacrylate-co-methyl acrylate) shell with nano alumina (nano-Al 2 O 3 ) inlay was synthesized through emulsion polymerization. Various techniques were used to characterize the as-prepared products so as to investigate the effect of nano-Al 2 O 3 on morphology and thermal performance, including scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and thermal conductivity measurement. The results showed that the products achieved the best performance with 16% (monomer mass) nano-Al 2 O 3 added under the optimal preparation conditions. The DSC results indicated that the phase change temperature of the composite exhibited appropriate phase change temperature and achieved high encapsulation efficiency. The thermal conductivity of the paraffin microcapsules is also significantly improved owing to the presence of high thermal conductive nano-Al 2 O 3 . This synthetic technique can be a perspective way to prepare the MEPCM with enhanced thermal transfer and phase change properties for potential applications to energy-saving building materials

  11. Use of a Paraffin Based Grout to Stabilize Buried Beryllium and Other Wastes

    International Nuclear Information System (INIS)

    Gretchen Matthern; Duane Hanson; Neal Yancey; Darrell Knudson

    2005-01-01

    The long term durability of WAXFIXi, a paraffin based grout, was evaluated for in situ grouting of activated beryllium wastes in the Subsurface Disposal Area (SDA), a radioactive landfill at the Radioactive Waste Management Complex, part of the Idaho National Laboratory (INL). The evaluation considered radiological and biological mechanisms that could degrade the grout using data from an extensive literature search and previous tests of in situ grouting at the INL. Conservative radioactive doses for WAXFIX were calculated from the ''hottest'' (i.e., highest-activity) Advanced Test Reactor beryllium block in the SDA.. These results indicate that WAXFIX would not experience extensive radiation damage for many hundreds of years. Calculation of radiation induced hydrogen generation in WAXFIX indicated that grout physical performance should not be reduced beyond the effects of radiation dose on the molecular structure. Degradation of a paraffin-based grout by microorganisms in the SDA is possible and perhaps likely, but the rate of degradation will be at a slower rate than found in the literature reviewed. The calculations showed the outer 0.46 m (18 in.) layer of each monolith, which represents the minimum expected distance to the beryllium block, was calculated to require 1,000 to 3,600 years to be consumed. The existing data and estimations of biodegradation and radiolysis rates for WAXFIX/paraffin do not indicate any immediate problems with the use of WAXFIX for grouting beryllium or other wastes in the SDA

  12. Paraffin-based immunohistochemistry in the evaluation of glomerular diseases in renal biopsies

    International Nuclear Information System (INIS)

    Rathore, M.U.; Khadim, M.T.; Atique, M.

    2012-01-01

    Objective: To determine sensitivity and specificity of paraffin-based immunohistochemistry in the evaluation of glomerular diseases in renal biopsies using immunofluorescence as gold standard. Study Design: Cross-sectional analytical study. Place and Duration of Study: Department of Histopathology, Armed Forces Institute of Pathology, Rawalpindi, from August 2008 to August 2009. Methodology: Seventy renal biopsy specimens fulfilling the inclusion criteria for light microscopy and immuno-fluorescence during the study period were evaluated. Antibodies to immunoglobulins (IgG, IgA, and IgM) and components of complement system (C3) were applied on 70 formalin-fixed paraffin-embedded renal biopsy specimens previously classified by means of light microscopy and immunofluorescence (IF). Staining for these antibodies was recorded as positive and negative for immunohistochemistry (IHC) and IF in paired proportions presuming IF as gold standard test. The sensitivity, specificity, positive predictive value and negative predictive value of individual antibody were calculated. Results: Of 70 patients, mean age was 33 +- 18 years ranging from 2 to 80 years. Forty five (64%) were males and 25 (36%) were females. The sensitivity, specificity and predictive values of individual antibodies to IgG, IgA, IgM and C3 were very low and generally in the range of 40 - 60%. Conclusion: The sensitivity, specificity and predictive values of immunohistochemistry on formalin-fixed paraffin-embedded renal biopsy specimens were very low and therefore, not suitable for evaluation of renal biopsies in current circumstances. (author)

  13. Fabrication and performances of microencapsulated paraffin composites with polymethylmethacrylate shell based on ultraviolet irradiation-initiated

    Energy Technology Data Exchange (ETDEWEB)

    Wang Yi, E-mail: wangyi@lut.cn [State Key Laboratory of Gansu Advanced Non-ferrous Metal Materials, Lanzhou University of Technology, Lanzhou 730050 (China); College of Petrochemical Technology, Lanzhou University of Technology, Lanzhou 730050 (China); Shi Huan [College of Petrochemical Technology, Lanzhou University of Technology, Lanzhou 730050 (China); Xia Tiandong [State Key Laboratory of Gansu Advanced Non-ferrous Metal Materials, Lanzhou University of Technology, Lanzhou 730050 (China); Zhang Ting; Feng Huixia [College of Petrochemical Technology, Lanzhou University of Technology, Lanzhou 730050 (China)

    2012-07-16

    In order to identify the validity of fabricating microencapsulated phase change material by ultraviolet irradiation-initiated method, the paraffin wax/polymethyl methacrylate microcapsules were prepared. The structural characteristics and thermal properties of the microcapsules were also determined by various techniques. The results of differential scanning calorimetry analyses indicate that the melting and freezing temperatures and latent heats of the microcapsules are 55.8 Degree-Sign C, 50.1 Degree-Sign C and 106.9 J g{sup -1}, 112.3 J g{sup -1}, respectively. Morphology and chemical characteristic analysis indicate that the spherical microcapsules were formed with average diameter of 0.21 {mu}m and maximum microencapsulation ratio of 66 wt.% without leakage of core materials. The results of accelerated thermal cyclic test show that the microcapsules have good thermal reliability and chemical stability although they were subjected 3000 melting/freezing cycles. Based on all these results, it can be concluded that the microencapsulated paraffin composites have good potential for thermal energy storage purposes and ultraviolet irradiation-initiated method is a prominent candidate for preparing microencapsulated PCMs. - Highlights: Black-Right-Pointing-Pointer Microencapsulated paraffin with PMMA shell was synthesized via self-assembly. Black-Right-Pointing-Pointer Microcapsules with excellent properties can be prepared by UV initiated method. Black-Right-Pointing-Pointer The microencapsulation ratio is as high as 66 wt.%. Black-Right-Pointing-Pointer Thermal properties are as high as comparable with microcapsules in the literature.

  14. Fabrication and performances of microencapsulated paraffin composites with polymethylmethacrylate shell based on ultraviolet irradiation-initiated

    International Nuclear Information System (INIS)

    Wang Yi; Shi Huan; Xia Tiandong; Zhang Ting; Feng Huixia

    2012-01-01

    In order to identify the validity of fabricating microencapsulated phase change material by ultraviolet irradiation-initiated method, the paraffin wax/polymethyl methacrylate microcapsules were prepared. The structural characteristics and thermal properties of the microcapsules were also determined by various techniques. The results of differential scanning calorimetry analyses indicate that the melting and freezing temperatures and latent heats of the microcapsules are 55.8 °C, 50.1 °C and 106.9 J g −1 , 112.3 J g −1 , respectively. Morphology and chemical characteristic analysis indicate that the spherical microcapsules were formed with average diameter of 0.21 μm and maximum microencapsulation ratio of 66 wt.% without leakage of core materials. The results of accelerated thermal cyclic test show that the microcapsules have good thermal reliability and chemical stability although they were subjected 3000 melting/freezing cycles. Based on all these results, it can be concluded that the microencapsulated paraffin composites have good potential for thermal energy storage purposes and ultraviolet irradiation-initiated method is a prominent candidate for preparing microencapsulated PCMs. - Highlights: ► Microencapsulated paraffin with PMMA shell was synthesized via self-assembly. ► Microcapsules with excellent properties can be prepared by UV initiated method. ► The microencapsulation ratio is as high as 66 wt.%. ► Thermal properties are as high as comparable with microcapsules in the literature.

  15. Comparison of Paraffin and Diesel Oil as Cultivation Medium Supplements for Preparing a Hydrocarbon-Degrading Bacterial Biomass

    Directory of Open Access Journals (Sweden)

    Dokukins Eduards

    2016-05-01

    Full Text Available The effect of liquid paraffin and diesel oil as nutrient amendments for hydrocarbon-degrading bacteria was compared. Different parameters were analyzed - optical density of bacterial suspension, oxygen consumption by biomass, morphology of bacteria, etc. In some experiments the paraffin was more preferable for microorganisms, but in other tests the results for both substances were similar. The influence of the comparable substances strongly depends on cultivation conditions.

  16. Experiment study on the thermal properties of paraffin/kaolin thermal energy storage form-stable phase change materials

    International Nuclear Information System (INIS)

    Lv, Peizhao; Liu, Chenzhen; Rao, Zhonghao

    2016-01-01

    Highlights: • Different particle sizes of kaolin were employed to load paraffin. • The effects and reasons of particle size on thermal conductivity were studied. • Thermal property and thermal stability of the composites were investigated. • The leakage and thermal storage and release rate of the composites were studied. • The effect of vacuum impregnation method on thermal conductivity was investigated. - Abstract: In this paper, different particle sizes of kaolin were employed to incorporate paraffin via vacuum impregnation method. The paraffin/kaolin composites were characterized by Scanning Electron Microscope (SEM), X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Differential Scanning Calorimeter (DSC) and Thermogravimetry (TG). The results showed that the paraffin/kaolin composite with the largest particle size of kaolin (K4) has the highest thermal conductivity (0.413 W/(m K) at 20 °C) among the diverse composites. The latent heat capacity of paraffin/K4 is 119.49 J/g and the phase change temperature is 62.4 °C. In addition, the thermal properties and thermal conductivities of paraffin/K4 with different mass fraction of K4 (0–60%) were investigated. The thermal conductivities of the composites were explained in microcosmic field. The phonon mean free path determines the thermal conductivity, and it can be significantly affected by temperature and the contact surface area. The leaks, thermal storage and release properties of pure paraffin and paraffin/kaolin composites were investigated and the composites presented good thermal stabilities.

  17. Understanding community norms surrounding tobacco sales.

    Directory of Open Access Journals (Sweden)

    Patricia A McDaniel

    Full Text Available In the US, denormalizing tobacco use is key to tobacco control; less attention has been paid to denormalizing tobacco sales. However, some localities have placed limits on the number and type of retailers who may sell tobacco, and some retailers have abandoned tobacco sales voluntarily. Understanding community norms surrounding tobacco sales may help accelerate tobacco denormalization.We conducted 15 focus groups with customers of California, New York, and Ohio retailers who had voluntarily discontinued tobacco sales to examine normative assumptions about where cigarettes should or should not be sold, voluntary decisions to discontinue tobacco sales, and government limits on such sales.Groups in all three states generally agreed that grocery stores that sold healthy products should not sell tobacco; California groups saw pharmacies similarly, while this was a minority opinion in the other two states. Convenience stores were regarded as a natural place to sell tobacco. In each state, it was regarded as normal and commendable for some stores to want to stop selling tobacco, although few participants could imagine convenience stores doing so. Views on government's role in setting limits on tobacco sales varied, with California and New York participants generally expressing support for restrictions, and Ohio participants expressing opposition. However, even those who expressed opposition did not approve of tobacco sales in all possible venues. Banning tobacco sales entirely was not yet normative.Limiting the ubiquitous availability of tobacco sales is key to ending the tobacco epidemic. Some limits on tobacco sales appear to be normative from the perspective of community members; it may be possible to shift norms further by problematizing the ubiquitous presence of cigarettes and drawing connections to other products already subject to restrictions.

  18. Understanding community norms surrounding tobacco sales.

    Science.gov (United States)

    McDaniel, Patricia A; Malone, Ruth E

    2014-01-01

    In the US, denormalizing tobacco use is key to tobacco control; less attention has been paid to denormalizing tobacco sales. However, some localities have placed limits on the number and type of retailers who may sell tobacco, and some retailers have abandoned tobacco sales voluntarily. Understanding community norms surrounding tobacco sales may help accelerate tobacco denormalization. We conducted 15 focus groups with customers of California, New York, and Ohio retailers who had voluntarily discontinued tobacco sales to examine normative assumptions about where cigarettes should or should not be sold, voluntary decisions to discontinue tobacco sales, and government limits on such sales. Groups in all three states generally agreed that grocery stores that sold healthy products should not sell tobacco; California groups saw pharmacies similarly, while this was a minority opinion in the other two states. Convenience stores were regarded as a natural place to sell tobacco. In each state, it was regarded as normal and commendable for some stores to want to stop selling tobacco, although few participants could imagine convenience stores doing so. Views on government's role in setting limits on tobacco sales varied, with California and New York participants generally expressing support for restrictions, and Ohio participants expressing opposition. However, even those who expressed opposition did not approve of tobacco sales in all possible venues. Banning tobacco sales entirely was not yet normative. Limiting the ubiquitous availability of tobacco sales is key to ending the tobacco epidemic. Some limits on tobacco sales appear to be normative from the perspective of community members; it may be possible to shift norms further by problematizing the ubiquitous presence of cigarettes and drawing connections to other products already subject to restrictions.

  19. Screening of short- and medium-chain chlorinated paraffins in selected riverine sediments and sludge from the Czech Republic

    International Nuclear Information System (INIS)

    Pribylova, Petra; Klanova, Jana; Holoubek, Ivan

    2006-01-01

    Wide distribution of chlorinated paraffins in the environment has already been demonstrated in several studies; however, information about their levels in the Central Europe is still very limited. First study focused on the SCCP contamination of the Czech aquatic environment have been performed recently, and its results motivated the authors to analyze sediments from a wide set of the Czech rivers in order to obtain more detailed information. Thirty-six sediment samples from eleven rivers and five drainage vents neighboring the chemical factories were analyzed; special attention was paid to the industrial areas. For the first time in the Czech Republic, medium-chain in addition to short-chain chlorinated paraffins were analyzed using GC-ECNI-MS. Chlorinated paraffins were detected in sediment samples on the concentration levels up to 347 ng g -1 for short-chain chlorinated paraffins, and 5575 ng g -1 for medium-chain chlorinated paraffins. Average chlorination degree of SCCPs was 65%. - Data on contamination of sediments from industrial areas fill the informational gap in the field of contamination of the Central Europe by chlorinated paraffins

  20. Accelerated Thermal Cycling Test of Microencapsulated Paraffin Wax/Polyaniline Made by Simple Preparation Method for Solar Thermal Energy Storage.

    Science.gov (United States)

    Silakhori, Mahyar; Naghavi, Mohammad Sajad; Metselaar, Hendrik Simon Cornelis; Mahlia, Teuku Meurah Indra; Fauzi, Hadi; Mehrali, Mohammad

    2013-04-29

    Microencapsulated paraffin wax/polyaniline was prepared using a simple in situ polymerization technique, and its performance characteristics were investigated. Weight losses of samples were determined by Thermal Gravimetry Analysis (TGA). The microencapsulated samples with 23% and 49% paraffin showed less decomposition after 330 °C than with higher percentage of paraffin. These samples were then subjected to a thermal cycling test. Thermal properties of microencapsulated paraffin wax were evaluated by Differential Scanning Calorimeter (DSC). Structure stability and compatibility of core and coating materials were also tested by Fourier transform infrared spectrophotometer (FTIR), and the surface morphology of the samples are shown by Field Emission Scanning Electron Microscopy (FESEM). It has been found that the microencapsulated paraffin waxes show little change in the latent heat of fusion and melting temperature after one thousand thermal recycles. Besides, the chemical characteristics and structural profile remained constant after one thousand thermal cycling tests. Therefore, microencapsulated paraffin wax/polyaniline is a stable material that can be used for thermal energy storage systems.

  1. Production of jet fuel range paraffins by low temperature polymerization of gaseous light olefins using ionic liquid

    International Nuclear Information System (INIS)

    Jiang, Peiwen; Wu, Xiaoping; Zhu, Lijuan; Jin, Feng; Liu, Junxu; Xia, Tongyan; Wang, Tiejun; Li, Quanxin

    2016-01-01

    Graphical abstract: A novel catalytic transformation of light olefins into jet fuel range iso-paraffins by the low-temperature olefin polymerizations under atmospheric conditions. - Highlights: • A novel transformation of light olefins to jet fuel range paraffins was demonstrated. • The synthetic fuels can be produced by atmospheric olefin polymerizations. • C 8 –C 15 iso-paraffins from light olefins was achieved with a selectivity of 80.6%. - Abstract: This work demonstrated a novel catalytic transformation of gaseous olefins into jet fuel range iso-paraffins by the low-temperature olefin polymerizations under atmospheric conditions. The production of the desired C 8 –C 15 iso-paraffins with the selectivity of 80.6 C mol% was achieved by the room-temperature polymerizations of gaseous light olefins using the [BMIM] Al 2 Cl 7 ionic liquid. The influences of the reaction conditions on the olefinic polymerizations were investigated in detail. The properties of hydrocarbons in the synthetic fuels were determined by the GC–MS analyses combined with 1 H NMR, and 13 C NMR analyses. The formation of C 8 –C 15 hydrocarbons from gaseous light olefins was illustrated by the identified products and the functional groups. This transformation potentially provides a useful avenue for the production of the most important components of iso-paraffins required in jet fuels.

  2. Fabrication and properties of microencapsulated-paraffin/gypsum-matrix building materials for thermal energy storage

    International Nuclear Information System (INIS)

    Su Junfeng; Wang Xinyu; Wang Shengbao; Zhao Yunhui; Huang Zhen

    2012-01-01

    Graphical abstract: DSC curves of microPCMs/gypsum composite samples before and after a thermal cycling treatment. Highlights: ► Microcapsules containing paraffin was fabricated by in-situ polymerization. ► Methanol-modified melamine–formaldehyde (MMF) was used as shell material. ► MicroPCMs/gypsum-matrix building materials were applied for solar energy storage. ► The structure and thermal conductivity of composites had been investigated. - Abstract: Microencapsulated phase change materials (microPCMs) have been widely applied in solid matrix as thermal-storage or temperature-controlling functional composites. The aim of this work was to prepare and investigate the properties of microPCMs/gypsum-matrix building materials for thermal energy storage. MicroPCMs contain paraffin was fabricated by in situ polymerization using methanol-modified melamine–formaldehyde (MMF) as shell material. A series of microPCMs samples were prepared under emulsion stirring rates in range of 1000–3000 r min −1 with core/shell weight ratios of 3/1, 2/1, 1/1, 1/2 and 1/3, respectively. The shell of microPCMs was smooth and compact with global shape, its thickness was not greatly affected by the core/shell ratio and emulsion stirring rate. DSC tests showed that the shell of microPCMs did not influence the phase change behavior of pure paraffin. It was found from TGA analysis that microPCMs samples containing paraffin lost their weight at the temperature of nearly 250 °C, which indicated that the PCM had been protected by shell. More shell material in microPCMs could enhance the thermal stability and provide higher compact condition for core material. After a 100-times thermal cycling treatment, the microPCMs contain paraffin also nearly did not change the phase change behaviors of PCM. With the increasing of weight contents of microPCMs in gypsum board, the thermal conductivity (λ) values of composites had decreased. The simulation of temperature tests proved that the

  3. Moderation for Professional Learning

    Science.gov (United States)

    Earle, Sarah

    2017-01-01

    Moderation is put forward as they key strategy for improving the reliability of teacher assessment. However, for many teachers the word "moderation" conjures up ideas of uncomfortable situations in which marking is being checked by others and there are prolonged arguments about tiny features of individual work. In this article, the…

  4. Methane pellet moderator development

    International Nuclear Information System (INIS)

    Foster, C.A.; Schechter, D.E.; Carpenter, J.M.

    2004-01-01

    A methane pellet moderator assembly consisting of a pelletizer, a helium cooled sub-cooling tunnel, a liquid helium cooled cryogenic pellet storage hopper and a 1.5L moderator cell has been constructed for the purpose demonstrating a system for use in high-power spallation sources. (orig.)

  5. Moderator for nuclear reactor

    International Nuclear Information System (INIS)

    Milgram, M.S.; Dunn, J.T.; Hart, R.S.

    1995-01-01

    This invention relates to a moderator for a nuclear reactor and more specifically, to a composite moderator. A moderator is designed to slow down, or thermalize, neutrons which are released during nuclear reactions in the reactor fuel. Pure or almost pure materials like light water, heavy water, beryllium or graphite are used singly as moderators at present. All these materials, are used widely. Graphite has a good mechanical strength at high temperatures encountered in the nuclear core and therefore is used as both the moderator and core structural material. It also exhibits a low neutron-capture cross section and high neutron scattering cross section. However, graphite is susceptible to attach by carbon dioxide and/or oxygen where applicable, and releases stress energy under certain circumstances, although under normal operating conditions these reactions can be controlled. (author). 1 tab

  6. Study of the hydro-isomerization of paraffins with 7 and 8 carbon atoms on bifunctional catalysts; Etude de l'hydroisomerisation des paraffines a 7 et 8 atomes de carbone sur catalyseurs bifonctionnels

    Energy Technology Data Exchange (ETDEWEB)

    Patrigeon, A.

    2000-10-11

    Due to the suppression of lead additives and the trend to decrease the aromatic and olefinic content in gasoline, the interest for new octane enhancement processes has increased, particularly for isomerization of C{sub 7} and C{sub 8} linear paraffins into higher octane number multi-branched paraffins. Up to the present day, no industrial bifunctional catalyst exists due to the high tendency of the paraffins to be cracked limiting the amount of multi-branched products. The aim of this work is to study the possibility of isomerizing linear C{sub 7} and C{sub 8} paraffins in two steps in order to increase the amount of formed multi-branched paraffins. The first step converts linear paraffins into mono-branched paraffins (that step is supposed to be the slowest one) carried out using one bifunctional catalyst. The second step converts the formed mono-branched paraffins into multi-branched paraffins using a second bifunctional catalyst. The aim is to determine the characteristics of the two catalysts. To study the first step, Pt/zeolite or Pt/meso-porous solid catalysts, with different acidities and porosities, were tested in n-heptane and n-octane hydro-conversion. The role of solid porosity on selectivities was clearly established. Molecular modelling was utilised to explain the observed selectivities. To study the second step, the 2-methyl-hexane and 2-methyl-heptane hydro-conversion on Pt/H-beta and Pt/H-Y was carried out. This lead to maximum multi-branched yields similar to those obtained with the n-heptane and n-octane hydro-conversion. That result shows that the two steps isomerization process is not necessarily required because no more multi-branched products are formed. A kinetic study on the n-heptane hydro-conversion was performed. The decomposition of isomerization and cracking reactions into elementary steps has shown the major role of the paraffins physio-sorption step in the zeolite pores. (author)

  7. Bisulfite-Based DNA Methylation Analysis from Recent and Archived Formalin-Fixed, Paraffin Embedded Colorectal Tissue Samples.

    Science.gov (United States)

    Kalmár, Alexandra; Péterfia, Bálint; Hollósi, Péter; Wichmann, Barnabás; Bodor, András; Patai, Árpád V; Schöller, Andrea; Krenács, Tibor; Tulassay, Zsolt; Molnár, Béla

    2015-09-01

    We aimed to test the applicability of formalin-fixed and paraffin-embedded (FFPE) tissue samples for gene specific DNA methylation analysis after using two commercially available DNA isolation kits. Genomic DNA was isolated from 5 colorectal adenocarcinomas and 5 normal adjacent tissues from "recent", collected within 6 months, and "archived", collected more than 5 years ago, FFPE tissues using either High Pure FFPET DNA Isolation kit or QIAamp DNA FFPE Tissue kit. DNA methylation analysis of MAL, SFRP1 and SFRP2 genes, known to be hypermethylated in CRC, was performed using methylation-sensitive high resolution melting (MS-HRM) analysis and sequencing. QIAamp (Q) method resulted in slightly higher recovery in archived (HP: 1.22 ± 3.18 μg DNA; Q: 3.00 ± 4.04 μg DNA) and significantly (p < 0.05) higher recovery in recent samples compared to High Pure method (HP) (HP: 4.10 ± 2.91 μg DNA; Q: 11.51 ± 7.50 μg DNA). Both OD260/280 and OD260/230 ratios were lower, but still high in the High Pure isolated archived and recent samples compared to those isolated with QIAamp. Identical DNA methylation patterns were detected for all 3 genes tested by MS-HRM with both isolation kits in the recent group. However, despite of higher DNA recovery in QIAamp slightly more reproducible methylation results were obtained from High Pure isolated archived samples. Sequencing confirmed DNA hypermethylation in CRCs. In conclusion, reproducible DNA methylation patterns were obtained from recent samples using both isolation kits. However, long term storage may affect the reliability of the results leading to moderate differences between the efficiency of isolation kits.

  8. Properties of form-stable paraffin/silicon dioxide/expanded graphite phase change composites prepared by sol–gel method

    International Nuclear Information System (INIS)

    Li, Min; Wu, Zhishen; Tan, Jinmiao

    2012-01-01

    Highlights: ► Paraffin/SiO 2 /EG composite PCM was prepared with sol–gel method. ► The thermal conductivity of SiO 2 /paraffin/EG is 94.7% higher than paraffin. ► The latent heat of paraffin/SiO 2 /EG composite is 104.4 J/g. -- Abstract: A form-stable paraffin/silicon dioxide (SiO 2 )/expanded graphite (EG) composite phase change material (PCM) was prepared by sol–gel method. Silica gel acts as the supporting material and EG is used to increase the thermal conductivity. The mass fractions of silicon oxide and graphite are 20.8% and 7.2%, respectively. The composite PCM was characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Fourier transformation infrared spectroscopy (FTIR) method. Thermal properties and thermal stability of the composite PCM were studied using differential scanning calorimetry (DSC). The result shows that paraffin was well dispersed in the network of silica gel and there is no chemical reaction between them. The phase change temperature of the paraffin/SiO 2 composite and the paraffin/SiO 2 /EG composite are 27.53 °C and 27.72 °C, respectively. The latent heat of the paraffin/SiO 2 composite and the paraffin/SiO 2 /EG composite are 112.8 J/g and 104.4 J/g, respectively. The thermal conductivity of the SiO 2 /paraffin composite and the SiO 2 /paraffin/EG composite are 28.2% and 94.7% higher than that of paraffin.

  9. Impacts of Artificial Reefs on Surrounding Ecosystems

    Science.gov (United States)

    Manoukian, Sarine

    Artificial reefs are becoming a popular biological and management component in shallow water environments characterized by soft seabed, representing both important marine habitats and tools to manage coastal fisheries and resources. An artificial reef in the marine environment acts as an open system with exchange of material and energy, altering the physical and biological characteristics of the surrounding area. Reef stability will depend on the balance of scour, settlement, and burial resulting from ocean conditions over time. Because of the unstable nature of sediments, they require a detailed and systematic investigation. Acoustic systems like high-frequency multibeam sonar are efficient tools in monitoring the environmental evolution around artificial reefs, whereas water turbidity can limit visual dive and ROV inspections. A high-frequency multibeam echo sounder offers the potential of detecting fine-scale distribution of reef units, providing an unprecedented level of resolution, coverage, and spatial definition. How do artificial reefs change over time in relation to the coastal processes? How accurately does multibeam technology map different typologies of artificial modules of known size and shape? How do artificial reefs affect fish school behavior? What are the limitations of multibeam technology for investigating fish school distribution as well as spatial and temporal changes? This study addresses the above questions and presents results of a new approach for artificial reef seafloor mapping over time, based upon an integrated analysis of multibeam swath bathymetry data and geoscientific information (backscatter data analysis, SCUBA observations, physical oceanographic data, and previous findings on the geology and sedimentation processes, integrated with unpublished data) from Senigallia artificial reef, northwestern Adriatic Sea (Italy) and St. Petersburg Beach Reef, west-central Florida continental shelf. A new approach for observation of fish

  10. High efficiency positron moderation

    International Nuclear Information System (INIS)

    Taqqu, D.

    1990-01-01

    A new positron moderation scheme is proposed. It makes use of electric and magnetic fields to confine the β + emitted by a radioactive source forcing them to slow down within a thin foil. A specific arrangement is described where an intermediary slowed-down beam of energy below 10 keV is produced. By directing it towards a standard moderator optimal conversion into slow positrons is achieved. This scheme is best applied to short lived β + emitters for which a 25% moderation efficiency can be reached. Within the state of the art technology a slow positron source intensity exceeding 2 x 10 10 e + /sec is achievable. (orig.)

  11. Interviewing the moderator

    DEFF Research Database (Denmark)

    Traulsen, Janine Morgall; Almarsdóttir, Anna Birna; Björnsdóttir, Ingunn

    2004-01-01

    There has been an upsurge of academic interest in using focus groups (FGs) as a main or stand-alone qualitative method. In this article, the authors introduce a recently developed ancillary method to FGs called interviewing the moderator. The method is employed immediately after an FG and consists...... of a one-on-one interview with the FG moderator by another member of the research team. The authors argue, with reference to a specific study, that interviewing the moderator adds a new and valuable dimension to group interviews used in research. They describe how this method came about and provide...

  12. Clinical efficacy and safety of polyethylene glycol 3350 versus liquid paraffin in the treatment of pediatric functional constipation.

    Science.gov (United States)

    Rafati, Mr; Karami, H; Salehifar, E; Karimzadeh, A

    2011-01-01

    Functional constipation is prevalent in children. Recently polyethylene glycol has been introduced as an effective and safe drug to treat chronic constipation. There are only a few clinical trials on comparison of PEG and liquid paraffin in childhood constipation. The purpose of this study was to evaluate clinical efficacy and safety of PEG 3350 solution and liquid paraffin in the treatment of children with functional constipation in Sari Toba clinic during the period of 2008-2009. Children with a history of functional constipation were subjects of this study. One hundred and sixty children of 2-12 years old with functional constipation were randomized in two PEG and paraffin treatment groups. Patients received either 1.0-1.5 g/kg/day PEG 3350 or 1.0-1.5 ml/kg/day liquid paraffin for 4 months. Clinical efficacy was evaluated by stool and encopresis frequency/week and overall treatment success rate was compared in two groups. Compared with the baseline, defecation frequency/ week increased significantly and encopresis frequency meaningfully decreased in two groups during the period of the study. Patients using PEG 3350 had more success rate (mean: 95.3%±3.7) compared with the patients in paraffin group (mean: 87.2%±7.1) (p=0.087). Administration of PEG 3350 were associated with less adverse events than liquid paraffin. In conclusion in treatment of pediatric functional constipation, regarding clinical efficacy and safety, PEG 3350 were at least as effective as liquid paraffin and but less adverse drug events.

  13. Clinical efficacy and safety of polyethylene glycol 3350 versus liquid paraffin in the treatment of pediatric functional constipation

    Directory of Open Access Journals (Sweden)

    E Salehifar

    2011-05-01

    Full Text Available "nBackground and the purpose of the study: Functional constipation is prevalent in children. Recently has been introduced as an effective and safe drug to treat chronic constipation. There are only a few clinical trials on comparison of PEG and liquid paraffin in childhood constipation. The purpose of this study was to evaluate clinical efficacy and safety of PEG 3350 solution and liquid paraffin in the treatment of children with functional constipation in Sari Toba clinic during the period of 2008-2009. "nMethods: Children with a history of functional constipation were subjects of this study. One hundred and sixty children of 2-12 years old with functional constipation were randomized in two PEG and paraffin treatment groups. Patients received either 1.0-1.5 g/kg/day PEG 3350 or 1.0-1.5 ml/kg/day liquid paraffin for 4 months. Clinical efficacy was evaluated by stool and encopresis frequency/week and overall treatment success rate was compared in two groups. "nResults and major conclusion: Compared with the baseline, defecation frequency/ week increased significantly and encopresis frequency meaningfully decreased in two groups during the period of the study. Patients using PEG 3350 had more success rate (mean: 95.3%±3.7 compared with the patients in paraffin group (mean: 87.2%±7.1 (p=0.087. Administration of PEG 3350 was associated with less adverse events than liquid paraffin. In conclusion in treatment of pediatric functional constipation , regarding clinical efficacy and safety, PEG 3350 were at least as effective as liquid paraffin and but less adverse drug events.

  14. Shape-stabilized phase change materials with high thermal conductivity based on paraffin/graphene oxide composite

    International Nuclear Information System (INIS)

    Mehrali, Mohammad; Latibari, Sara Tahan; Mehrali, Mehdi; Metselaar, Hendrik Simon Cornelis; Silakhori, Mahyar

    2013-01-01

    Highlights: ► The composite PCM was prepared with impregnation method. ► Shapes stabilized phase change material made with paraffin and GO composite. ► Determine effects of GO composite on shape stabilized PCM properties. ► The composite PCM has good thermal stability and form-stability. ► The composite PCM has much higher thermal conductivity than that of paraffin. - Abstract: This paper mainly focuses on the preparation, characterization, thermal properties and thermal stability and reliability of new form-stable composite phase change materials (PCMs) prepared by vacuum impregnation of paraffin within graphene oxide (GO) sheets. SEM and FT-IR techniques and TGA and DSC analysis are used for characterization of material and thermal properties. The composite PCM contained 48.3 wt.% of paraffin without leakage of melted PCM and therefore this composite found to be a form-stable composite PCM. SEM results indicate that the paraffin bounded into the pores of GO. FT-IR analysis showed there was no chemical reaction between paraffin and GO. Temperatures of melting and freezing and latent heats of the composite were 53.57 and 44.59 °C and 63.76 and 64.89 kJ/kg, respectively. Thermal cycling tests were done by 2500 melting/freezing cycling for verification of the form-stable composite PCM in terms of thermal reliability and chemical stability. Thermal conductivity of the composite PCM was highly improved from 0.305 to 0.985 (W/mk). As a result, the prepared paraffin/GO composite is appropriate PCM for thermal energy storage applications because of their acceptable thermal properties, good thermal reliability, chemical stability and thermal conductivities

  15. Paraffin dispersant application for cleaning subsea flow lines in the deep water Gulf of Mexico cottonwood development

    Energy Technology Data Exchange (ETDEWEB)

    Jennings, David; White, Jake; Pogoson, Oje [Baker Hughes Inc., Houston, TX (United States); Barros, Dalmo; Ramachandran, Kartik; Bonin, George; Waltrich, Paulo; Shecaira, Farid [PETROBRAS America, Houston, TX (United States); Ziglio, Claudio [Petroleo Brasileiro S.A. (CENPES/PETROBRAS), Rio de Janeiro, RJ (Brazil). Centro de Pesquisa e Desenvolvimento

    2012-07-01

    This paper discusses a paraffin dispersant (in seawater) application to clean paraffin deposition from a severely restricted 17.4-mile dual subsea flow line system in the Gulf of Mexico Cottonwood development. In principle, dispersant treatments are simple processes requiring effective dispersant packages and agitation to break-up and disperse deposition. Dispersants have been used onshore for treating wax deposition for decades. Implementation of a treatment in a long deep water production system, however, poses numerous challenges. The Cottonwood application was one of the first ever deep water dispersant applications. The application was designed in four separate phases: pre-treatment displacement for hydrate protection, dispersant treatment for paraffin deposition removal, pigging sequence for final flow line cleaning, and post-treatment displacement for hydrate protection. In addition, considerable job planning was performed to ensure the application was executed in a safe and environmentally responsible manner. Two dynamically positioned marine vessels were used for pumping fluids and capturing returns. The application was extremely successful in restoring the deep water flow lines back to near pre-production state. Final pigging operations confirmed the flow lines were cleaned of all restrictions. Significant paraffin deposition was removed in the application. Approximately 900 bbls of paraffin sludge was recovered from the 4000 bbl internal volume flow line loop. Furthermore, the application was completed with zero discharge of fluids. The application provided significant value for the Cottonwood development. It allowed production from wells to be brought on-line at a higher capacity, thereby generating increased revenue. It also allowed resumption of routine pigging operations. As such, the Cottonwood dispersant application illustrates that with proper planning and execution, paraffin dispersant treatments can be highly effective solutions for cleaning

  16. Clinical efficacy and safety of polyethylene glycol 3350 versus liquid paraffin in the treatment of pediatric functional constipation

    Science.gov (United States)

    Rafati, MR.; Karami, H.; Salehifar, E.; Karimzadeh, A.

    2011-01-01

    Background and the purpose of the study Functional constipation is prevalent in children. Recently polyethylene glycol has been introduced as an effective and safe drug to treat chronic constipation. There are only a few clinical trials on comparison of PEG and liquid paraffin in childhood constipation. The purpose of this study was to evaluate clinical efficacy and safety of PEG 3350 solution and liquid paraffin in the treatment of children with functional constipation in Sari Toba clinic during the period of 2008–2009. Methods Children with a history of functional constipation were subjects of this study. One hundred and sixty children of 2–12 years old with functional constipation were randomized in two PEG and paraffin treatment groups. Patients received either 1.0–1.5 g/kg/day PEG 3350 or 1.0–1.5 ml/kg/day liquid paraffin for 4 months. Clinical efficacy was evaluated by stool and encopresis frequency/week and overall treatment success rate was compared in two groups. Results and major conclusion Compared with the baseline, defecation frequency/ week increased significantly and encopresis frequency meaningfully decreased in two groups during the period of the study. Patients using PEG 3350 had more success rate (mean: 95.3%±3.7) compared with the patients in paraffin group (mean: 87.2%±7.1) (p=0.087). Administration of PEG 3350 were associated with less adverse events than liquid paraffin. In conclusion in treatment of pediatric functional constipation, regarding clinical efficacy and safety, PEG 3350 were at least as effective as liquid paraffin and but less adverse drug events. PMID:22615652

  17. Segmented fuel and moderator rod

    International Nuclear Information System (INIS)

    Doshi, P.K.

    1987-01-01

    This patent describes a continuous segmented fuel and moderator rod for use with a water cooled and moderated nuclear fuel assembly. The rod comprises: a lower fuel region containing a column of nuclear fuel; a moderator region, disposed axially above the fuel region. The moderator region has means for admitting and passing the water moderator therethrough for moderating an upper portion of the nuclear fuel assembly. The moderator region is separated from the fuel region by a water tight separator

  18. Establishment of a Pcr Technique for Determination of Htlv-1 Infection in Paraffin-Embedded Tissues

    Directory of Open Access Journals (Sweden)

    M Rastin

    2007-04-01

    Full Text Available Introduction: HTLV-1 , the first known human retrovirus belongs to oncovirus subfamily of retroviruses. The major characteristic of HTLV-1 is its highly restricted geographic prevalence. Northern part of Khorasan is an endemic region of HTLV-1 infection. Epidemiological studies can help in designing preventive programs for HTLV-1 infection. The aim of this study was the establishment of a PCR technique for determination of HTLV-1 infection in paraffin-embedded tissues. Methods: In this experimental laboratory study for establishment of a technique, PCR was initially optimized using Beta-actin primers on various formalin fixed paraffin-embedded tissues from liver, spleen, skin and lymph nodes. The optimized concentration of Mgcl2 was 2mm, primer was 8 pmol. Optimized concentration of DNA was different according to the kind of tissue. HTLV-1 infection was determined by applying tax, pol, env and LTR primers on 50 paraffin-embedded lymph node tissues . The reporoducibility of this technique was shown for skin and lymph node tissues infected with HTLV-1. Resuls: In 50 lymph node tissues, one case with pathologic diagnosis of NHL was positive with all 5 sets of primers (tax, Pol, env and LTR primers and the other case was positive with only two sets of tax primers but was negative with pol, env and LTR primers. The prevalence of infection was 2% among lymph node specimens. (1 of 50 specimens and if the second case is considered, the prevalence would be 4%. Conclusion: Comparison of the results of this study with another study on blood specimens (seroprevalence2.3% was not statistically significant thus confirming the results of one another. (P=0.883

  19. Calculation of Physicochemical Properties for Short- and Medium-Chain Chlorinated Paraffins

    Science.gov (United States)

    Glüge, Juliane; Bogdal, Christian; Scheringer, Martin; Buser, Andreas M.; Hungerbühler, Konrad

    2013-06-01

    Short- and medium-chain chlorinated paraffins are potential PBT chemicals (persistent, bioaccumulative, toxic) and short-chain chlorinated paraffins are under review for inclusion in the UNEP Stockholm Convention on Persistent Organic Pollutants. Despite their high production volume of more than one million metric tonnes per year, only few data on their physicochemical properties are available. We calculated subcooled-liquid vapor pressure, subcooled-liquid solubility in water and octanol, Henry's law constant for water and octanol, as well as the octanol-water partition coefficient with the property calculation methods COSMOtherm, SPARC, and EPI Suite™, and compared the results to experimental data from the literature. For all properties, good or very good agreement between calculated and measured data was obtained for COSMOtherm; results from SPARC were in good agreement with the measured data except for subcooled-liquid water solubility, whereas EPI Suite™ showed the largest discrepancies for all properties. After critical evaluation of the three property calculation methods, a final set of recommended property data for short- and medium-chain chlorinated paraffins was derived. The calculated property data show interesting relationships with chlorine content and carbon chain length. Increasing chlorine content does not cause pronounced changes in water solubility and octanol-water partition coefficient (KOW) as long as it is below 55%. Increasing carbon chain length leads to strong increases in KOW and corresponding decreases in subcooled-liquid water solubility. The present data set can be used in further studies to assess the environmental fate and human exposure of this relevant compound class.

  20. Thermochemical emission and transformation of chlorinated paraffins in inert and oxidizing atmospheres.

    Science.gov (United States)

    Xin, Shanzhi; Gao, Wei; Wang, Yawei; Jiang, Guibin

    2017-10-01

    Chlorinated paraffins (CPs) generally function as flame retardants and plasticizers in various materials. They are most likely to be processed by thermal processes during the entire life cycle. However, data on the formation and emission of CPs during thermal processes are still not fully understood. In this study, we simulated industrial thermal processes to investigate the emission of medium-chain chlorinated paraffins (MCCPs) and short-chain chlorinated paraffins (SCCPs) using commercial CP52 as the feedstock. We found that CP52 decomposed very easily at 210-320 °C. The decomposition of CPs generated large quantities of MCCPs and SCCPs. These remained in the residue at low temperature (∼200 °C) and were gradually released into the gas phase at higher temperatures. MCCPs and SCCPs were not detected in either the residue or the gas phase when the temperature exceeded 400 °C. However, considerable concentrations of aromatic and chlorinated aromatic hydrocarbons (Cl-PAHs) were identified in the gas phase, and they were formed as the amount of SCCPs and MCCPs decreased. Cl-PAHs were dominated by low-chlorinated chlorobenzenes, polychlorinated biphenyls, and polychlorinated naphthalenes. Oxygen promoted the release and decomposition of SCCPs in the gas phase. The results of the present study revealed the release of MCCPs and SCCPs and their synergistic emission with Cl-PAHs when CPs were subjected to heat. This work may also provide data for developing multiple techniques to control the emission of CPs and Cl-PAHs. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Heat and mass transfer analysis for paraffin/nitrous oxide burning rate in hybrid propulsion

    Science.gov (United States)

    Ben-Basat (Sisi), Shani; Gany, Alon

    2016-03-01

    This research presents a physical-mathematical model for the combustion of liquefying fuels in hybrid combustors, accounting for blowing effect on the heat transfer. A particular attention is given to a paraffin/nitrous oxide hybrid system. The use of a paraffin fuel in hybrid propulsion has been considered because of its much higher regression rate enabling significantly higher thrust compared to that of common polymeric fuels. The model predicts the overall regression rate (melting rate) of the fuel and the different mechanisms involved, including evaporation, entrainment of droplets of molten material, and mass loss due to melt flow on the condensed fuel surface. Prediction of the thickness and velocity of the liquid (melt) layer formed at the surface during combustion was done as well. Applying the model for an oxidizer mass flux of 45 kg/(s m2) as an example representing experimental range, it was found that 21% of the molten liquid undergoes evaporation, 30% enters the gas flow by the entrainment mechanism, and 49% reaches the end of the combustion chamber as a flowing liquid layer. When increasing the oxidizer mass flux in the port, the effect of entrainment increases while that of the flowing liquid layer along the surface shows a relatively lower contribution. Yet, the latter is predicted to have a significant contribution to the overall mass loss. In practical applications it may cause reduced combustion efficiency and should be taken into account in the motor design, e.g., by reinforcing the paraffin fuel with different additives. The model predictions have been compared to experimental results revealing good agreement.

  2. Use of microbes for paraffin cleanup at Naval Petroleum Reserve No. 3

    Energy Technology Data Exchange (ETDEWEB)

    Giangiacomo, L.; Khatib, A.

    1995-12-31

    Naval Petroleum Reserve No. 3 (NPR-3), also known as Teapot Dome, is a government-owned oil field in Natrona County, Wyoming. It is an asymmetrical anticline located on the western edge of the Powder River Basin, just south of the Salt Creek Anticline. Production started in 1922, and today the field is a marginally economic stripper field with average production of less than 3 BOPD (0.5 m{sup 3}/D) per well. Total field production is about 1,800 BOPD (286 m{sup 3}/D). The Second Wall Creek Formation was waterflooded from 1979 until June 1992 with poor results due to the extensive natural fracture system in this sandstone unit. Since water injection ceased, reservoir pressure has declined to very low levels. Liquids extraction and reinjection of the gas produced from high-GOR wells along the gas-oil contact continues, but the average gas cap pressure has fallen to approximately 150 psi (1.03 MPa) from an original pressure of 1,120 psi (7.72 MPa). Since the oil is highly paraffinic, wax deposition in the hydraulic fractures and the perforations has become a serious production problem. Microbial treatment was considered as a possible low-cost solution. Four wells were selected in the Second Wall Creek Reservoir with severe paraffin problems and production rates high enough to economically justify the treatment. Problems were experienced with the production of thick oil after approximately three months. This was interpreted to be a result of previously immobile paraffin being cleaned up. A slight decrease in the decline rate was seen in the wells, although some external factors cloud the interpretation. Microbial treatments were discontinued because of marginal economics. Three of the four wells produced additional oil and had a positive incremental cash flow. Oil viscosity tests did indicate that some positive microbial thinning was occurring, and changes to the treatment procedure may potentially yield more economic results in the future.

  3. Real-time quantitative PCR of microdissected paraffin-embedded breast carcinoma

    DEFF Research Database (Denmark)

    Gjerdrum, Lise Mette; Sorensen, Boe Sandahl; Kjeldsen, Eigil

    2004-01-01

    We studied the feasibility of using real-time quantitative PCR to determine HER-2 DNA amplification and mRNA expression in microdissected formalin-fixed, paraffin-embedded breast tumors and compared this with standard immunohistochemistry (IHC) and fluorescent in situ hybridization (FISH) methods...... tumors as being amplified. Interestingly, all these scored 2+ with the HercepTest, but were negative using FISH. We believe that real-time quantitative PCR analysis of HER-2 DNA amplification following microdissection represents a useful supplementary or perhaps even an alternative technique...

  4. Non-parathyroid hypercalcemia associated with paraffin oil injection in 12 younger male bodybuilders

    DEFF Research Database (Denmark)

    Sølling, Anne Sophie Koldkjær; Tougaard, Birgitte G; Harsløf, Torben

    2018-01-01

    INTRODUCTION: Injection of paraffin oil to augment muscles size is a troubling phenomenon known to cause a foreign body reaction with formation of granulomas. In a few case reports, long-term side effects have been reported in terms of hypercalcemia and renal failure. METHODS: We identified a case...... the normal range or slightly elevated. Follow-up measurements showed marked hypercalciuria with nearly normal levels of bone turnover markers. A correlation was found between levels of peptidyl dipeptidase and calcitriol (R = 0.812, P = 0.050). Treatment with antiresorptive agents seemed less effective than...

  5. Paraffin-based hybrid rocket engines applications: A review and a market perspective

    Science.gov (United States)

    Mazzetti, Alessandro; Merotto, Laura; Pinarello, Giordano

    2016-09-01

    Hybrid propulsion technology for aerospace applications has received growing attention in recent years due to its important advantages over competitive solutions. Hybrid rocket engines have a great potential for several aeronautics and aerospace applications because of their safety, reliability, low cost and high performance. As a consequence, this propulsion technology is feasible for a number of innovative missions, including space tourism. On the other hand, hybrid rocket propulsion's main drawback, i.e. the difficulty in reaching high regression rate values using standard fuels, has so far limited the maturity level of this technology. The complex physico-chemical processes involved in hybrid rocket engines combustion are of major importance for engine performance prediction and control. Therefore, further investigation is ongoing in order to achieve a more complete understanding of such phenomena. It is well known that one of the most promising solutions for overcoming hybrid rocket engines performance limits is the use of liquefying fuels. Such fuels can lead to notably increased solid fuel regression rate due to the so-called "entrainment phenomenon". Among liquefying fuels, paraffin-based formulations have great potentials as solid fuels due to their low cost, availability (as they can be derived from industrial waste), low environmental impact and high performance. Despite the vast amount of literature available on this subject, a precise focus on market potential of paraffins for hybrid propulsion aerospace applications is lacking. In this work a review of hybrid rocket engines state of the art was performed, together with a detailed analysis of the possible applications of such a technology. A market study was carried out in order to define the near-future foreseeable development needs for hybrid technology application to the aforementioned missions. Paraffin-based fuels are taken into account as the most promising segment for market development

  6. Neutron and gamma ray attenuation of asphalt; Comparison with paraffin and water

    International Nuclear Information System (INIS)

    Abdul-Majid, S.; Kutbi, I.I.

    1996-01-01

    Asphalt is a low cost, readily available, easy-to-cast material which is rich in hydrogen and carbon, elements most effective for fast-neutron shielding. Unlike paraffin, the material can easily be mixed with boron containing compounds, an, element of high absorption cross-section for slow neutrons. The 241 Am-Be neutron and gamma attenuation characteristic of asphalt were studied. The source is having wide applications in industry and geophysics field work. Comparisons were made with paraffin and water. The source activity was 1.11 x 1,011 Bq (3 Ci) with a neutron emission rate of 6.6 x 106 n s -1 and a tolerance of +10%. The neutron dose-equivalent rate at 1 m was 66 mSv h -1 , while the associated gamma ray exposure was ∼1.9 mC kg -1 h -1 of the bare source. A neutron remmeter was used for the neutron dose-equivalent rate measurements, which produces an energy response that approximates human body dose equivalent over a wide range of neutron energy. An air filled ionization chamber was used for the exposure rate measurements. The slow neutrons were measured by a BF 3 gas filled detector. The shielding materials were confined in an aluminum cylinder of 1 mm wall thickness where the source was kept in the middle. The neutron dose rate, the gamma ray exposure rate, and the slow neutron count rate were measured at different shield radii and at different distances from its outer surface. The neutron doses of asphalt at the surface of cylindrical shields of 8, 12, 16, 20, and 24 cm radii in mSv h -1 were 0.85, 0.4, 0.25, 0.13, and 0.06, respectively, while the gamma ray exposure mC kg -1 h -1 were 7, 4.4 2.5, 1.3, and 0.88, respectively. The neutron dose rate attenuation of asphalt was very close to that of water, but slightly lower than that of paraffin, while the gamma ray attenuation was close to that of water but higher than that of paraffin

  7. Is light narrowing possible with dense-vapor paraffin coated cells for atomic magnetometers?

    Science.gov (United States)

    Han, Runqi; Balabas, Mikhail; Hovde, Chris; Li, Wenhao; Roig, Hector Masia; Wang, Tao; Wickenbrock, Arne; Zhivun, Elena; You, Zheng; Budker, Dmitry

    2017-12-01

    We investigated the operation of an all-optical rubidium-87 atomic magnetometer with amplitude-modulated light. To study the suppression of spin-exchange relaxation, three schemes of pumping were implemented with room-temperature and heated paraffin coated vacuum cells. Efficient pumping and accumulation of atoms in the F=2 ground state were obtained. However, the sought-for narrowing of the resonance lines has not been achieved. A theoretical analysis of the polarization degree is presented to illustrate the absence of light narrowing due to radiation trapping at high temperature.

  8. Methanogenic Paraffin Biodegradation: Alkylsuccinate Synthase Gene Quantification and Dicarboxylic Acid Production.

    Science.gov (United States)

    Oberding, Lisa K; Gieg, Lisa M

    2018-01-01

    Paraffinic n -alkanes (>C 17 ) that are solid at ambient temperature comprise a large fraction of many crude oils. The comparatively low water solubility and reactivity of these long-chain alkanes can lead to their persistence in the environment following fuel spills and pose serious problems for crude oil recovery operations by clogging oil production wells. However, the degradation of waxy paraffins under the anoxic conditions characterizing contaminated groundwater environments and deep subsurface energy reservoirs is poorly understood. Here, we assessed the ability of a methanogenic culture enriched from freshwater fuel-contaminated aquifer sediments to biodegrade the model paraffin n -octacosane (C 28 H 58 ). Compared with that in controls, the consumption of n -octacosane was coupled to methane production, demonstrating its biodegradation under these conditions. Smithella was postulated to be an important C 28 H 58 degrader in the culture on the basis of its high relative abundance as determined by 16S rRNA gene sequencing. An identified assA gene (known to encode the α subunit of alkylsuccinate synthase) aligned most closely with those from other Smithella organisms. Quantitative PCR (qPCR) and reverse transcription qPCR assays for assA demonstrated significant increases in the abundance and expression of this gene in C 28 H 58 -degrading cultures compared with that in controls, suggesting n -octacosane activation by fumarate addition. A metabolite analysis revealed the presence of several long-chain α,ω-dicarboxylic acids only in the C 28 H 58 -degrading cultures, a novel observation providing clues as to how methanogenic consortia access waxy hydrocarbons. The results of this study broaden our understanding of how waxy paraffins can be biodegraded in anoxic environments with an application toward bioremediation and improved oil recovery. IMPORTANCE Understanding the methanogenic biodegradation of different classes of hydrocarbons has important

  9. An adaptive self-healing ionic liquid nanocomposite membrane for olefin-paraffin separations.

    Science.gov (United States)

    Pitsch, Fee; Krull, Florian F; Agel, Friederike; Schulz, Peter; Wasserscheid, Peter; Melin, Thomas; Wessling, Matthias

    2012-08-16

    An adaptive self-healing ionic liquid nanocomposite membrane comprising a multi-layer support structure hosting the ionic salt [Ag](+) [Tf(2) N](-) is used for the separation of the olefin propylene and the paraffin propane. The ionic salt renders liquid like upon complexation with propylene, resulting in facilitated transport of propylene over propane at benchmark-setting selectivity and permeance levels. The contacting with acetylene causes the ionic salt to liquefy without showing evidence of forming explosive silver acetylide. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Penis deformity after intra-urethral liquid paraffin administration in a young male: a case report

    OpenAIRE

    Kokkonouzis, Ioannis; Antoniou, Georgios; Droulias, Athanasios

    2008-01-01

    Background Self-induced injections of liquid substances mainly for penis enlargement is a well-documented but still rather uncommon practice in the western world. Case presentation Herein we present the case of a 30-year-old male who self-inflicted, twice in a six-month-period, intra-urethral liquid paraffin and tied up his penis with a cord in order to achieve both enlargement and elongation. He arrived in our emergency department suffering from suprapubic pain; physical examination revealed...

  11. Modeling of high speed micro rotors in moderate flow confinement

    NARCIS (Netherlands)

    Dikmen, E.; van der Hoogt, Peter; Aarts, Ronald G.K.M.; Sas, P.; Bergen, B.

    2008-01-01

    The recent developments in high speed micro rotating machinery lead to the need for multiphysical modeling of the rotor and the surrounding medium. In this study, thermal and flow induced effects on rotor dynamics of geometries with moderate flow confinement are studied. The structure is modeled via

  12. Efeito do campo magnético na precipitação de parafinas Magnetic field effect on paraffin deposition

    Directory of Open Access Journals (Sweden)

    Nelson de Oliveira Rocha

    1998-02-01

    Full Text Available In the oil industry, the paraffination phenomenon is a major problem during oil production, displacement and treatment. Paraffin deposition in subsea flowlines, surface equipment, production string or even in the reservoir, can cause significant and increasing oil losses. To minimize paraffin precipitation, the application of magnetic field in the petroleum path has been suggested based on empiric studies. In this study, we assembled a labscale magnetic conditioner to determine the influence of magnetic field on the physical-chemical properties of two fluids : oil and a paraffin mixture. We observed that magnetic field reduce sample aparent viscosity due to crystal morphology alteration.

  13. Treatment of paraffin problems in petroleum production with chemicals; Tratamento de problemas parafinicos com agentes quimicos na producao de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Jennings, David; Yin, Ralph; Weispfennig, Klaus; Newberry, Mike [Baker Petrolite, Sugar Land, TX (United States)

    2004-07-01

    Paraffin problems can greatly reduce production of certain crude oils, if correct methods to control the problems are not used. These problems are primarily related to flow line deposition and reduction in crude oil flow properties caused by wax network growth. Deep water production and production of high-wax content crude oils can be especially problematic. Much of the petroleum production in Brazil falls in these categories: in the Campos Basin and in Bahia. Paraffin problems can be controlled with diverse methods. These methods include use of: pigging, insulation, heating, and chemicals. Sometimes, the use of chemicals can be very practical, alone or in combination with other methods. This paper discusses the use of chemicals for the treatment of paraffin problems. Three types of treatments are discussed: prevention of deposition in flow lines with paraffin inhibitors; improvement in flow properties of crude oils with pour point depressants, and removal of paraffin deposits with dispersants. The discussion includes the physical effects of the treatment chemicals and field examples. (author)

  14. Preparation, Characterization and Thermal Properties of Paraffin Wax – Expanded Perlite Form-Stable Composites for Latent Heat Storage

    Directory of Open Access Journals (Sweden)

    Tugba GURMEN OZCELIK

    2017-02-01

    Full Text Available In this study, form-stable composite phase change materials (PCM for latent heat storage were prepared by impregnating paraffin wax into the pores of the expanded perlite (EP. The characterization of the composite PCMs was performed by FTIR, TGA, SEM and DSC analysis. The melting point and heat of fusion were determined for 25 % paraffin included composite, as 54.3 °C and 94.71 J/g and for 45 % paraffin included composite as 53.6 °C and 106.69 J/g, respectively. The FTIR results showed that there were no chemical reaction between the perlite and paraffin. TGA analysis indicated that both composite PCMs had good thermal stability. SEM images showed that the paraffin was dispersed uniformly into the pores and on the EP surface. There was no leakage and degradation at the composite PCMs after heating and cooling cycles. According to the results, both prepared composites showed good thermal energy storage properties, reliability and stability. All results suggested that the presented form- stable composite PCMs has great potential for thermal energy storage applications.DOI: http://dx.doi.org/10.5755/j01.ms.23.1.13661

  15. Study on improving the heat storage property of Ba(OH)2·8H2O with paraffin

    Science.gov (United States)

    Cui, Kaixuan; Liu, Liqiang; Sun, Mingjie

    2017-12-01

    Barium hydroxide octahydrate is the crystalline hydration salt with the highest latent heat density within the phase change temperature interval of 0-120 °C and it has a broad application prospect as a phase-change material (PCM). Firstly, red copper test tube was used for the melting—solidification heat cycle experiment in this paper, which was verified by the corrosion experiment of barium hydroxide solution. After the thermogravimetric analysis, it is found that paraffin can effectively reduce the evaporation escape of barium hydroxide octahydrate crystal water within 100 °C. Repeated heat cycle experiments indicated that the paraffin with larger coverage mass fraction can reduce the inhibiting effect of barium hydroxide octahydrate crystal water more obviously. X-ray diffraction analysis indicated that the phase composition of the barium hydroxide octahydrate sample covered with 50 wt% paraffin nearly had no change, while the sample not covered with paraffin has the weight loss ratio of 34.67% and reacted with CO2 in the air, generating BaCO3. In summary, paraffin can not only inhibit the evaporation of crystal water, but also effectively isolate the air to prevent barium hydroxide octahydrate from denaturation. This greatly improved the practicability of barium hydroxide octahydrate as a PCM, laying a good foundation for the further application of barium hydroxide octahydrate.

  16. Digital dewaxing of Raman signals: discrimination between nevi and melanoma spectra obtained from paraffin-embedded skin biopsies.

    Science.gov (United States)

    Tfayli, Ali; Gobinet, Cyril; Vrabie, Valeriu; Huez, Regis; Manfait, Michel; Piot, Olivier

    2009-05-01

    Malignant melanoma (MM) is the most severe tumor affecting the skin and accounts for three quarters of all skin cancer deaths. Raman spectroscopy is a promising nondestructive tool that has been increasingly used for characterization of the molecular features of cancerous tissues. Different multivariate statistical analysis techniques are used in order to extract relevant information that can be considered as functional spectroscopic descriptors of a particular pathology. Paraffin embedding (waxing) is a highly efficient process used to conserve biopsies in tumor banks for several years. However, the use of non-dewaxed formalin-fixed paraffin-embedded tissues for Raman spectroscopic investigations remains very restricted, limiting the development of the technique as a routine analytical tool for biomedical purposes. This is due to the highly intense signal of paraffin, which masks important vibrations of the biological tissues. In addition to being time consuming and chemical intensive, chemical dewaxing methods are not efficient and they leave traces of the paraffin in tissues, which affects the Raman signal. In the present study, we use independent component analysis (ICA) on Raman spectral images collected on melanoma and nevus samples. The sources obtained from these images are then used to eliminate, using non-negativity constrained least squares (NCLS), the paraffin contribution from each individual spectrum of the spectral images of nevi and melanomas. Corrected spectra of both types of lesion are then compared and classified into dendrograms using hierarchical cluster analysis (HCA).

  17. Temperature-dependent thermal properties of a paraffin phase change material embedded with herringbone style graphite nanofibers

    International Nuclear Information System (INIS)

    Warzoha, Ronald J.; Weigand, Rebecca M.; Fleischer, Amy S.

    2015-01-01

    Highlights: • The thermal properties of a PCM with nanofibers are determined. • The solid-phase thermal conductivity scales exponentially with volume fraction. • The liquid-phase thermal conductivity is only enhanced beyond a critical percolation threshold. • The nanoscale interface resistance depends on the nanoparticle’s dimensionality. • The thermal diffusivity and volumetric heat capacity of the nanoenhanced PCMs are found. - Abstract: In many studies, carbon nanoparticles with high values of thermal conductivity (10–3000 W/m K) have been embedded into phase change thermal energy storage materials (PCMs) in order to enhance their bulk thermal properties. While a great deal of work to date has focused on determining the effect of these nanoparticles on a PCM’s solid phase thermal properties, little is known about their effect on its liquid phase thermal properties. Thus, in this study, the effect of implanting randomly oriented herringbone style graphite nanofibers (HGNF, average diameter = 100 nm, average length = 20 μm) on the bulk thermal properties of an organic paraffin PCM (IGI 1230A, T melt = 329.15 K) in both the solid and liquid phase is quantified. The bulk thermal conductivity, volumetric heat capacity and thermal diffusivity of HGNF/PCM nanocomposites are obtained as a function of temperature and HGNF volume loading level. It is found that the property enhancement varies significantly depending on the material phase. In order to explain the difference between solid and liquid phase thermal properties, heat flow at the nanoparticle–PCM and nanoparticle–nanoparticle interfaces is examined as a function of HGNF loading level and temperature. To do this, the solid and liquid phase thermal boundary resistances (TBRs) between the nanoparticles and the surrounding PCM and/or between contacting nanoparticles are found. Results suggest that the TBR at the HGNF–PCM interface is nearly double the TBR across the HGNF–HGNF interface in

  18. Influence of different moderator materials on characteristics of neutron fluxes generated under irradiation of lead target with proton beams

    International Nuclear Information System (INIS)

    Sosnin, A.N.; Polanski, A.; Petrochenkov, S.A.

    2002-01-01

    Neutron fields generated in extended heavy (Z ≥ 82) targets under irradiation with proton beams at energies in the range of 1 GeV are investigated. Influence of different moderators on the spectra and multiplicities of neutrons escaping the surface of the assembly consisting of a lead target (diam. 8 cm x 20 cm or diam. 8 cm x 50 cm) screened by variable thickness of polyethylene or graphite, respectively, was compared. It is shown that the effectiveness of graphite as a material used in such assemblies to moderate spallation neutrons down to thermal energies is significantly lower than that of paraffin

  19. Influence of Different Moderator Materials on Characteristics of Neutron Fluxes Generated under Irradiation of Lead Target with Proton Beams

    CERN Document Server

    Sosnin, A N; Polanski, A; Petrochenkov, S A; Golovatyuk, V M; Krivopustov, M I; Bamblevski, V P; Westmeier, W; Odoj, R; Brandt, R; Robotham, H; Hashemi-Nezhad, S R; Zamani-Valassiadou, M

    2002-01-01

    Neutron fields generated in extended heavy (Z\\geq 82) targets under irradiation with proton beams at energies in the range of 1 GeV are investigated. Influence of different moderators on the spectra and multiplicities of neutrons escaping the surface of the assembly consisting of a lead target (\\varnothing 8 cm\\times 20 cm or \\varnothing 8cm\\times 50 cm) screened by variable thickness of polyethylene or graphite, respectively, was compared in the present work. It is shown that the effectiveness of graphite as a material used in such assemblies to moderate spallation neutrons down to thermal energies is significantly lower than that of paraffin.

  20. Cold moderators at ORNL

    International Nuclear Information System (INIS)

    Lucas, A. T.

    1997-09-01

    The Advanced Neutron Source (ANS) cold moderators were not an 'Oak Ridge first', but would have been the largest both physically and in terms of cold neutron flux. Two cold moderators were planned each 410 mm in diameter and containing about 30L of liquid deuterium. They were to be completely independent of each other. A modular system design was used to provide greater reliability and serviceability. When the ANS was terminated, upgrading of the resident High Flux Isotope Reactor (HFIR) was examined and an initial study was made into the feasibility of adding a cold source. Because the ANS design was modular, it was possible to use many identical design features. Sub-cooled liquid at 4 bar abs was initially chosen for the HFIR design concept, but this was subsequently changed to 15 bar abs to operate above the critical pressure. As in the ANS, the hydrogen will operate at a constant pressure throughout the temperature range and a completely closed loop with secondary containment was adopted. The heat load of 2 kW made the heat flux comparable with that of the ANS. Subsequent studies into the construction of cryogenic moderators for the proposed new Synchrotron Neutron source indicated that again many of the same design concepts could be used. By connecting the two cold sources together in series, the total heat load of 2 kW is very close to that of the HFIR allowing a very similar supercritical hydrogen system to be configured. The two hydrogen moderators of the SNS provide a comparable heat load to the HFIR moderator. It is subsequently planned to connect the two in series and operate from a single cold loop system, once again using supercritical hydrogen. The spallation source also provided an opportunity to re-examine a cold pellet solid methane moderator operating at 20K.

  1. Use of a Paraffin Based Grout to Stabilize Buried Beryllium and Other Wastes

    Energy Technology Data Exchange (ETDEWEB)

    Gretchen Matthern; Duane Hanson; Neal Yancey; Darrell Knudson

    2005-12-01

    The long term durability of WAXFIXi, a paraffin based grout, was evaluated for in situ grouting of activated beryllium wastes in the Subsurface Disposal Area (SDA), a radioactive landfill at the Radioactive Waste Management Complex, part of the Idaho National Laboratory (INL). The evaluation considered radiological and biological mechanisms that could degrade the grout using data from an extensive literature search and previous tests of in situ grouting at the INL. Conservative radioactive doses for WAXFIX were calculated from the "hottest" (i.e., highest-activity) Advanced Test Reactor beryllium block in the SDA.. These results indicate that WAXFIX would not experience extensive radiation damage for many hundreds of years. Calculation of radiation induced hydrogen generation in WAXFIX indicated that grout physical performance should not be reduced beyond the effects of radiation dose on the molecular structure. Degradation of a paraffin-based grout by microorganisms in the SDA is possible and perhaps likely, but the rate of degradation will be at a slower rate than found in the literature reviewed. The calculations showed the outer 0.46 m (18 in.) layer of each monolith, which represents the minimum expected distance to the beryllium block, was calculated to require 1,000 to 3,600 years to be consumed. The existing data and estimations of biodegradation and radiolysis rates

  2. Development of Composite PCMs by Incorporation of Paraffin into Various Building Materials

    Directory of Open Access Journals (Sweden)

    Shazim Ali Memon

    2015-02-01

    Full Text Available In this research, we focused on the development of composite phase-change materials (CPCMs by incorporation of a paraffin through vacuum impregnation in widely used building materials (Kaolin and ground granulated blast-furnace slag (GGBS. The composite PCMs were characterized using environmental scanning electron microscopy (ESEM, Fourier transform infrared spectroscopy (FT-IR, differential scanning calorimetry (DSC and thermogravimetric analysis (TGA techniques. Moreover, thermal performance of cement paste composite PCM panels was evaluated using a self-designed heating system. Test results showed that the maximum percentage of paraffin retained by Kaolin and GGBS was found to be 18% and 9%, respectively. FT-IR results show that CPCMs are chemically compatible. The phase-change temperatures of CPCMs were in the human comfort zone, and they possessed considerable latent-heat storage capacity. TGA results showed that CPCMs are thermally stable, and they did not show any sign of degradation below 150 °C. From thermal cycling tests, it was revealed that the CPCMs are thermally reliable. Thermal performance tests showed that in comparison to the control room model, the room models prepared with CPCMs reduced both the temperature fluctuations and maximum indoor center temperature. Therefore, the prepared CPCMs have some potential in reducing peak loads in buildings when applied to building facade.

  3. Identification of tumor specimens by DNA analysis in a case of histocytological paraffin tissue block swapping

    Science.gov (United States)

    Raina, Anupuma; Yadav, Bhuvnesh; Ali, Sher; Das Dogra, Tirath

    2011-01-01

    We report on a patient who was diagnosed with high-grade breast carcinoma by all the pre-surgery clinical evidence of malignancy, but histopathological reports did not reveal any such tumor residue in the post-surgical tissue block. This raised a suspicion that either exchange of block, labeling error, or a technical error took place during gross examination of the tissue. The mastectomy residue was unprocurable to sort out the problem. So, two doubtful paraffin blocks were sent for DNA fingerprinting analysis. The partial DNA profiles (8-9/15 loci) were obtained from histocytological blocks. The random matching probability for both the paraffin blocks and the patient’s blood were found to be 1 in 4.43E4, 1.89E6, and 8.83E13, respectively for Asian population. Multiplex short tandem repeat analysis applied in this case determined that the cause of tumor absence was an error in gross examination of the post-surgical tissue. Moreover, the analysis helped in justifying the therapy given to the patient. Thus, with DNA fingerprinting technique, it was concluded that there was no exchange of the blocks between the two patients operated on the same day and the treatment given to the concerned patient was in the right direction. PMID:21674839

  4. Diagnosis of Nocardia paucivorans central nervous system infection by DNA sequencing from paraffin-embedded tissue.

    Science.gov (United States)

    Schiaroli, Elisabetta; Pasticci, Maria Bruna; De Carolis, Elena; Mello, Enrica; Pallotto, Carlo; Leli, Christian; De Socio, Giuseppe Vittorio; Baldelli, Franco; Sanguinetti, Maurizio; Mencacci, Antonella

    2016-06-01

    Infections by Nocardia spp. are generally regarded as opportunistic diseases in immunocompromised patients, but can also affect immunocompetent subjects. Such infections represent an important diagnostic challenge for clinicians and microbiologists, and diagnosis is frequently delayed or even conducted post mortem. A 54-year-old man was admitted to our hospital because of ventriculitis and relapsing brain abscess. Five months prior, this patient had undergone external ventricular drain and surgery for a cerebellar abscess. Histopathology demonstrated pyogenic inflammatory reaction, microbiologic investigations proved negative and empiric antimicrobial therapy was administered for a total of eight weeks. Six weeks later, the patient developed relapsing neurologic manifestations. On reviewing the patient's clinical history it emerged that the patient had suffered pneumonia two months prior to neurosurgery, treated with amoxicillin/clavulanate 3g a day and levofloxacin 500mg a day for three weeks. On the CNS relapsing manifestations, nocardiosis was suspected and DNA sequencing from the formalin-fixed paraffin-embedded cerebellar tissue collected during neurosurgery allowed diagnosis of Nocardia paucivorans infection. The patient received medical therapy for 11 months. At follow-up, eight months after treatment was discontinued, the patient was aymptomatic. Nocardia spp. infections need to be suspected not only in immunocompromised, but also in immunocompetent patients. Proper samples need to be collected for proper microbiologic investigations. Paraffin-embedded tissue genomic sequencing can be a useful tool for diagnosis of nocardiosis.

  5. Concentrations and congener profiles of chlorinated paraffins in domestic polymeric products in China.

    Science.gov (United States)

    Wang, Chu; Gao, Wei; Liang, Yong; Wang, Yawei; Jiang, Guibin

    2018-03-21

    Chlorinated paraffins (CPs) are widely used in domestic polymeric products as plasticizers and fire retardants. In this study, concentrations and congener profiles of short-chain and medium-chain chlorinated paraffins (SCCPs and MCCPs) were investigated in domestic polymeric products, including plastics, rubber and food packaging in China. The average concentrations of SCCPs in polyethylene terephthalate (PET), polypropylene (PP), polyethylene (PE) and food packaging were 234, 3968, 150 and 188 ng/g, respectively and the corresponding average concentrations of MCCPs in these samples were 37.4, 2537, 208 and 644 ng/g, respectively. The concentrations of CPs in rubber and polyvinylchloride (PVC) were significantly higher than in other matrices. The highest concentrations of SCCPs and MCCPs were found in a PVC cable sheath with 191 mg/g and 145 mg/g, respectively. Congener group profiles analysis indicated C 11 - and C 13 -congener groups were predominant in carbon homologues of SCCPs, and C 14 -congener groups were predominant in MCCPs. High levels of SCCPs and MCCPs in domestic polymeric products implied that they might be a significant source to the environment and human exposure. Copyright © 2018. Published by Elsevier Ltd.

  6. PrPSc detection in formalin-fixed paraffin-embedded tissue by ELISA

    Directory of Open Access Journals (Sweden)

    Nicholson Eric M

    2011-10-01

    Full Text Available Abstract Background Formalin-fixed paraffin-embedded tissue is regularly employed in the diagnosis of transmissible spongiform encephalopathies (TSE by immunohistochemistry (IHC, the standard by which all other TSE diagnostic protocols are judged. While IHC affords advantages over diagnostic approaches that typically utilize fresh or frozen tissue, such as Western blot and ELISA, the process of fixing, staining, and analyzing individual sections by hand does not allow for rapid or high throughput screening. However, preservation of tissues in formalin is not dependent upon the availability of refrigeration. Findings Formalin-fixed paraffin-embedded tissues from TSE transmission studies of scrapie in sheep, chronic wasting disease in white-tailed deer or transmissible mink encephalopathy in cattle were cut at 5 μm thickness. Samples containing the tissue equivalent of as little as one 5 μm section can be used to readily discriminate positive from negative samples. Conclusions This approach cannot replace IHC but may be used along with IHC as both a more rapid and readily high throughput screen where fresh or frozen tissues are not available or impractical.

  7. Paraffin-gel tissue-mimicking material for ultrasound-guided needle biopsy phantom.

    Science.gov (United States)

    Vieira, Sílvio L; Pavan, Theo Z; Junior, Jorge E; Carneiro, Antonio A O

    2013-12-01

    Paraffin-gel waxes have been investigated as new soft tissue-mimicking materials for ultrasound-guided breast biopsy training. Breast phantoms were produced with a broad range of acoustical properties. The speed of sound for the phantoms ranged from 1425.4 ± 0.6 to 1480.3 ± 1.7 m/s at room temperature. The attenuation coefficients were easily controlled between 0.32 ± 0.27 dB/cm and 2.04 ± 0.65 dB/cm at 7.5 MHz, depending on the amount of carnauba wax added to the base material. The materials do not suffer dehydration and provide adequate needle penetration, with a Young's storage modulus varying between 14.7 ± 0.2 kPa and 34.9 ± 0.3 kPa. The phantom background material possesses long-term stability and can be employed in a supine position without changes in geometry. These results indicate that paraffin-gel waxes may be promising materials for training radiologists in ultrasound biopsy procedures. Copyright © 2013 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.

  8. Impact of the rheological studies in the transport for pipeline of paraffinic crude oils

    International Nuclear Information System (INIS)

    Rodriguez, L; Vidales, H; Castaneda, M; Leal, O; Barrero R; Garzon, J

    2000-01-01

    The results of this applied research contribute fundamental elements for handling paraffinic crude oils (pipeline design and operation) and the optimization of the use of Pour Point Depressor additives. The rheological studies support the fluid-dynamic analyses that accurately predict the pipeline transport operation, unlike traditional parameters such as pour point and cloud point. Evaluations of rheological behavior was carried out at the laboratory level in concentric viscometers and were scaled at the pilot plant level in a fluid-dynamic test circuit in pipes with diameters from 1.27 to 15.24 cm (1/2 to 6 inches), where the laboratory scale was confirmed. The tests were performed under strain rate temperature and conditions similar to those of pipeline and flow line operation in production fields. Also, the viability to restart pumping after a prolonged shutdown with extreme temperatures was calculated, evaluating creep stress. The study has allowed us to transport Cupiagua crude oil without the PPD additive in a segregated manner, showing that despite its high pour point 300K (27 grades Celsius), in dynamic conditions similar to those in the pipeline, the crude oil flows at temperatures near 283K (10 Celsius degrades) without putting the integrity of the pipe in danger and within operational and equipment restrictions for the company operating the pipeline. This has generated significant savings, due to the additive as well as the possibility to segregate the crude oils, which facilitates the operation of the paraffin plant at the Barrancabermeja Industrial Complex

  9. Application of edible paraffin oil for cationic dye removal from water using emulsion liquid membrane.

    Science.gov (United States)

    Zereshki, Sina; Daraei, Parisa; Shokri, Amin

    2018-05-18

    Using an emulsion liquid membrane based on edible oils is investigated for removing cationic dyes from aqueous solutions. There is a great potential for using edible oils in food industry extraction processes. The parameters affecting the stability of the emulsion and the extraction rate were studied. These parameters were the emulsification time, the stirring speed, the surfactant concentration, the internal phase concentration, the feed phase concentration, the volume ratio of internal phase to organic phase and the treat ratio. In order to stabilize the emulsion without using a carrier, edible paraffin oil and heptane are used at an 80:20 ratio. The optimum conditions for the extraction of methylene blue (MB), crystal violet and methyl violet (CV and MV) cationic dyes using edible paraffin oil as an environment friendly solvent are represented. A removal percentage of 95% was achieved for a mixture of dyes. The optimum concentration of sodium hydroxide in the internal phase, which results a stabile emulsion with a high stripping efficiency of 96%, was 0.04 M. An excellent membrane recovery was observed and the extraction of dyes did not decrease up to seven run cycles. Copyright © 2018 Elsevier B.V. All rights reserved.

  10. Acute unintentional intoxication with paraffin in a 25-year old patient - clinical case report.

    Science.gov (United States)

    Chibishev, Andon; Simonovska, Natasa

    2014-08-01

    "Fire-breathing" or "fire-eating" is a special kind of street art where the acts are always stunning, spectacular and amazing. People exhibiting this kind of show are professionals, not rare amateurs, who use different kind of fuels, usually hydrocarbons, in order to produce a pillar of fire. Intoxications caused by ingestion or inhalation of liquid paraffin, used as a fuel while performing, are numerous and various. We present a clinical case report of a 25-year old, previously healthy, amateur "fire-breather". During October, 2010 this young men arrived at the Emergency Unit of the University Clinic for toxicology and Urgent Internal Medicine in a severe clinical condition, after his unsuccessful attempt to perform real "fire-breathing". He had fever, strong headaches, mild abdominal and chest pain and he also had difficulties breathing and persistent dry cough. The patient was extremely dyspneic with peripheral cyanosis and shortness of breath. "Fire-breathers" must be viewed as a population at risk of paraffin-induced pneumonia, which has low mortality rate, but still is related with numerous and various chronic complications. Our patient was first in a life threatening, extremely serious clinical condition which was urgently treated with appropriate vigorous and effective therapy. This therapeutic protocol led to successful full recovery of these young men, who luckily didn't exhibit any chronic complications. Copyright © 2014 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.

  11. Numerical Analysis of a Paraffin/Metal Foam Composite for Thermal Storage

    Science.gov (United States)

    Di Giorgio, P.; Iasiello, M.; Viglione, A.; Mameli, M.; Filippeschi, S.; Di Marco, P.; Andreozzi, A.; Bianco, N.

    2017-01-01

    In the last decade, the use of Phase Change Materials (PCMs) as passive thermal energy storage has been widely studied both analytically and experimentally. Among the PCMs, paraffins show many advantages, such as having a high latent heat, a low vapour pressure, being chemically inert, stable and non-toxic. But, their thermal conductivity is very low with a high volume change during the melting process. An efficient way to increase their poor thermal conductivity is to couple them with open cells metallic foams. This paper deals with a theoretical analysis of paraffin melting process inside an aluminum foam. A mathematical model is developed by using the volume-averaged governing equations for the porous domain, made up by the PCM embedded into the metal foam. Non-Darcian and buoyancy effects are considered in the momentum equation, while the energy equations are modelled with the Local Thermal Non-Equilibrium (LTNE) approach. The PCM liquefaction is treated with the apparent heat capacity method and the governing equations are solved with a finite-element scheme by COMSOL Multiphysics®. A new method to calculate the coupling coefficients needed for the thermal model has been developed and the results obtained have been validated comparing them to experimental data in literature.

  12. Household and caregiver characteristics and behaviours as predictors of unsafe exposure of children to paraffin appliances.

    Science.gov (United States)

    Van Niekerk, A; Govender, R; Hornsby, N; Swart, L

    2017-06-01

    This study examines adult safety knowledge and practices regarding the use of paraffin cooking appliances. The use of these is common in South Africa with injury risks that are poorly understood. This cross-sectional study was in an informal settlement in Johannesburg, South Africa, where children were reportedly at high risk for burns. This study sought to clarify relationships between key risks and developed individual and composite variables from theoretical constructs and operational definitions of risks for burns. Risks included Child Use of Paraffin Appliances, Child Proximity to Cooking, Risky Stove Use, Caregiver's Burn Treatment Knowledge, Children Locked in House, Children Alone in House. Number of children remains as in proof as this was not a composite scale. Child Proximity to Cooking was associated with more children in the home. Households where children were in greater proximity to cooking were 6 times more likely to be left alone at home, with caregivers with no education over 100 times more likely to lock their children at home. Children locked in were often from homes where caregivers used appliances unsafely. In settings with hazardous energy use, compressed household configurations, and families with multiple children, Risky Stove Use and the practice of locking children in the home may be catastrophic. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

  13. Coupled moderator neutronics

    International Nuclear Information System (INIS)

    Russell, G.J.; Pitcher, E.J.; Ferguson, P.D.

    1995-01-01

    Optimizing the neutronic performance of a coupled-moderator system for a Long-Pulse Spallation Source is a new and challenging area for the spallation target-system designer. For optimal performance of a neutron source, it is essential to have good communication with instrument scientists to obtain proper design criteria and continued interaction with mechanical, thermal-hydraulic, and materials engineers to attain a practical design. A good comprehension of the basics of coupled-moderator neutronics will aid in the proper design of a target system for a Long-Pulse Spallation Source

  14. Paraffin Phase Change Material for Maintaining Temperature Stability of IceCube Type of CubeSats in LEO

    Science.gov (United States)

    Choi, Michael K.

    2015-01-01

    The MLA and IFA of the instrument on the IceCube require a 20 C temperature and a thermal stability of +/-1 C. The thermal environment of the ISS orbit for the IceCube is very unstable due to solar beta angles in the -75deg to +75deg range. Additionally the instrument is powered off in every eclipse to conserve electrical power. These two factors cause thermal instability to the MLA and IFA. This paper presents a thermal design of using mini paraffin PCM packs to meet the thermal requirements of these instrument components. With a 31 g mass plus a 30% margin of n-hexadecane, the MLA and IFA are powered on for 32.3 minutes in sunlight at a 0deg beta angle to melt the paraffin. The powered-on time increases to 38 minutes at a 75deg (+/-) beta angle. When the MLA and IFA are powered off, the paraffin freezes.

  15. Formation of the second organic phase during uranyl nitrate extraction from aqueous solution by 30% tributylphosphate solution in paraffin

    International Nuclear Information System (INIS)

    Yhrkin, V.G.

    1996-01-01

    For extraction systems aqueous solution of uranyl nitrate-30% solution of tributylphosphate in individual paraffins from C 13 to C 17 the influence of the second organic phase of uranyl nitrate concentration in aqueous and organic phases, the length of hydrocarbon chain of paraffin hydrocarbon and temperature from 25 to 50 deg C on formation conditions has been defected. A special method of achieving the conditions of organic phase stratification from three-phase region, involving definition of equilibrium phases composition by density and refractive index, has been elaborated for more precise definition of organic phase homogeneity region. It has been revealed that without addition of nitric acid to uranyl nitrate solution the organic phase homogeneity limits can be achieved solely on paraffins C 15 , C 16 and C 17 and only under conditions similar to equeous phase saturation in terms of uranyl nitrate. 16 refs., 2 figs

  16. Comparison of the effectiveness of orthotic intervention, kinesiotaping, and paraffin treatments in patients with carpal tunnel syndrome: A single-blind and randomized controlled study.

    Science.gov (United States)

    Mansiz Kaplan, Basak; Akyuz, Gulseren; Kokar, Serdar; Yagci, Ilker

    2018-02-17

    The aim of the study was to compare different conservative treatments in patients with carpal tunnel syndrome (CTS). A single-blind randomized controlled study. Patients (n = 169) diagnosed with mild or moderate CTS were screened; 110 met study requirements. The patients were randomized into 3 groups. The control (CON) comparison provided to all patients was a fabricated night orthotic which held the wrist in a neutral position. The second group received adjunctive kinesiotaping (KIN) and the third group received paraffin (PARA). All patients were evaluated clinically, electrophysiologically, and ultrasonographically before treatment and at 3 weeks, 3 months, and 6 months. There were 36 patients in CON, 37 in KIN, and 37 in PARA. Pain reduction in KIN was better than the other groups at 3 weeks (mean difference [MD] in CON 2.4 ± 2.5, KIN 3.7 ± 2.0, PARA 2.7 ± 2.3; P < .01) and 6 months (MD in CON 3.4 ± 3.0, KIN 4.9 ± 3.1, PARA 3.7 ± 2.9; P < .05). KIN pain reduction was better than CON at 3 months (MD in CON 3.8 ± 2.8, KIN 5.0 ± 2.5; P < .05). Reduction of the cross-sectional area of median nerve at the level of radioulnar joint was greater for KIN than CON at 3 weeks (MD in CON 0.0 ± 0.5, KIN 0.3 ± 0.7; P < .01) than PARA at 3 months (MD in KIN 0.3 ± 0.8, PARA 0.0 ± 0.8; P < .05) and both groups at 6 months (MD in CON 0.1 ± 0.8, KIN 0.5 ± 0.9, PARA 0.0 ± 1.0 P < .05). Adding KIN to night use of an orthotic was more effective in achieving symptomatic and structural improvements than either the orthotic alone or adjunctive use of paraffin in patients with mild and moderate CTS. Copyright © 2018 Hanley & Belfus. Published by Elsevier Inc. All rights reserved.

  17. HIV behavioural surveillance among refugees and surrounding host ...

    African Journals Online (AJOL)

    We used a standardised behavioural surveillance survey (BSS), modified to be directly relevant to populations in conflict and post-conflict settings as well as to their surrounding host populations, to survey the populations of a refugee settlement in south-western Uganda and its surrounding area. Two-stage probability ...

  18. Investigation of the readout electronics of DELPHI surround muon chamber

    International Nuclear Information System (INIS)

    Khovanskij, N.; Krumshtejn, Z.; Ol'shevskij, A.; Sadovskij, A.; Sedykh, Yu.; Molnar, J.; Sicho, P.; Tomsa, Z.

    1995-01-01

    The characteristics of the readout electronics of the DELPHI surround muon chambers with various AMPLEX chips (AMPLEX 16 and AMPLEX-SICAL) are presented. This electronics is studied in a cosmic rays test of the real surround muon chamber model. 4 refs., 6 figs., 1 tab

  19. Preparation and thermal performance of paraffin/Nano-SiO2 nanocomposite for passive thermal protection of electronic devices

    International Nuclear Information System (INIS)

    Wang, Yaqin; Gao, Xuenong; Chen, Peng; Huang, Zhaowen; Xu, Tao; Fang, Yutang; Zhang, Zhengguo

    2016-01-01

    Highlights: • Three types of paraffin/nano-SiO 2 nanocomposites were prepared and characterized. • Thermo-physical properties of these composites were determined and compared. • One composite with lower thermal conductivity showed better thermal insulation properties. • This composite was identified as thermal insulation material for electronic components. - Abstract: In this paper, three grades of nano silicon dioxide (nano-SiO 2 ), NS1, NS2 and NS3, were mixed into paraffin to prepare nanocomposites as novel insulation materials for electronic passive thermal protection applications. The optimal mass percentages of paraffin for the three composites, NS1P, NS2P and NS3P, were determined to be 75%, 70% and 65%, respectively. Investigations by means of scanning electron micrographs (SEM), differential scanning calorimeter (DSC), thermogravimetric analysis (TG), hot disk analyzer and thermal protection performance tests were devoted to the morphology, thermal properties and thermal protection performance analysis of composites. Experimental results showed that paraffin uniformly distributed into the pores and on the surface of nano-SiO 2 . Melting points of composites declined and experimental latent heat became lower than the calculated values with the decrease of nano-SiO 2 pore size. The NS1P composite had larger thermal storage capacity, better reliability and stability compared with NS2P and NS3P. In addition, compared with 90% wt.% paraffin/EG composite, the incorporation of NS1 (25 wt.%) into paraffin caused not only 63.2% reduction in thermal conductivity, but also 21.8% increase in thermal protection time affected by the ambient temperature. Thus those good properties confirmed that NS1P (75 wt.%) composite was a viable candidate for protecting electronic devices under high temperature environment.

  20. Clinical significance of assessing Her2/neu expression in gastric cancer with dual tumor tissue paraffin blocks.

    Science.gov (United States)

    Ge, Xiaowen; Wang, Haixing; Zeng, Haiying; Jin, Xuejuan; Sujie, Akesu; Xu, Chen; Liu, Yalan; Huang, Jie; Ji, Yuan; Tan, Yunshan; Liu, Tianshu; Hou, Yingyong; Qin, Jing; Sun, Yihong; Qin, Xinyu

    2015-06-01

    One paraffin block is routinely used for human epidermal growth factor receptor 2 (Her2/neu) immunohistochemistry (IHC) assessment. Here, we investigated if picking 2 paraffin blocks for Her2/neu evaluation on 1 slide is an economical, efficient, and practical method, which may reduce false negativity of Her2/neu IHC assessment due to intratumoral heterogeneity. A total of 251 gastric cancer (GC) patients were divided into a cohort using 1 tumor tissue paraffin block (single-block group, n = 132) and a cohort using dual tumor tissue paraffin blocks (dual-block group, n = 119) when evaluating Her2/neu expression status by IHC. In dual-block group, we combined the results from 2 different paraffin blocks and used the higher one as the final score. The number of IHC 1+, 2+, and 3+ specimens in the single-block group was 31 (23.5%), 40 (30.3%), and 19 (14.4%), respectively. The combined final IHC score in the dual-block group of 1+, 2+, and 3+ was 26 (21.8%), 34 (28.6%), and 23 (19.3%), respectively. Inconsistent Her2/neu expression between blocks was found in 36 (30.3%) cases in the dual-block group. The pooled data in the single-block group and the dual-block group indicated that, when using dual blocks, the Her2/neu-positive (3+) rate of GC was higher compared to that in the single-block group. Our results implied that using dual paraffin blocks to assess Her2/neu expression of GC may help identify more patients with Her2/neu-positive GC who could benefit from targeted therapy, by reducing false-negative rate of Her2 status assessment. This is an efficient, economical, and practical method for Her2/neu evaluation of GC. Copyright © 2015 Elsevier Inc. All rights reserved.

  1. Stimulus size dependence of hue changes induced by chromatic surrounds.

    Science.gov (United States)

    Kellner, Christian Johannes; Wachtler, Thomas

    2016-03-01

    A chromatic surround induces a change in the perceived hue of a stimulus. This shift in hue depends on the chromatic difference between the stimulus and the surround. We investigated how chromatic induction varies with stimulus size and whether the size dependence depends on the surround hue. Subjects performed asymmetric matching of color stimuli with different sizes in surrounds of different chromaticities. Generally, induced hue shifts decreased with increasing stimulus size. This decrease was quantitatively different for different surround hues. However, when size effects were normalized to an overall induction strength, the chromatic specificity was largely reduced. The separability of inducer chromaticity and stimulus size suggests that these effects are mediated by different neural mechanisms.

  2. Moderator Chemistry Program

    International Nuclear Information System (INIS)

    Dewitt, L.V.; Gibbs, A.; Lambert, D.P.; Bohrer, S.R.; Fanning, R.L.; Houston, M.W.; Stinson, S.L.; Deible, R.W.; Abdel-Khalik, S.I.

    1990-11-01

    Over the past fifteen months, the Systems Chemistry Group of the Reactor Engineering Department has undertaken a comprehensive study of the Department's moderator chemistry program at Savannah River Site (SRS). An internal review was developed to formalize and document this program. Objectives were as outlined in a mission statement and action plan. In addition to the mission statement and action plan, nine separate task reports have been issued during the course of this study. Each of these task reports is included in this document as a chapter. This document is an organized compilation of the individual reports issued by the Systems Chemistry Group in assessment of SRS moderator chemistry to determine if there were significant gaps in the program as ft existed in October, 1989. While these reviews found no significant gaps in that mode of operation, or any items that adversely affected safety, items were identified that could be improved. Many of the items have already been dear with or are in the process of completion under this Moderator Chemistry Program and other Reactor Restart programs. A complete list of the items of improvement found under this assessment is found in Chapter 9, along with a proposed time table for correcting remaining items that can be improved for the chemistry program of SRS reactors. An additional external review of the moderator chemistry processes, recommendations, and responses to/from the Reactor Corrosion Mitigation Committee is included as Appendix to this compilation

  3. Den moderate revolution

    DEFF Research Database (Denmark)

    Larsen, Bøje

    "normale" industrivirksomheder, men den er absolut set begrænset. Årsagerne til denne kun "moderate revolution" af organisationsformerne diskuteres: Er det fordi klassisk organisation og social nærkontakt er nødvendig i den nye økonomi, eller er det manglende fantasi og tryghedsbehov? Begge muligheder...

  4. Cryogenic moderator design

    International Nuclear Information System (INIS)

    Diplock, B.R.

    1983-01-01

    This paper describes the present design of the two cold moderators to be built for the Spallation Neutron Source. It discusses the reasons behind a number of the design features and highlights several problem areas requiring solutions before a final design can be constructed

  5. In Everything Moderation

    Centers for Disease Control (CDC) Podcasts

    For many people, drinking alcohol is a regular part of social occasions, but moderation is important. Excessive alcohol consumption can lead to serious health and social problems. A recent report found that binge drinking is common among women and girls. In this podcast, Dr. Dafna Kanny discusses the dangers of binge drinking.

  6. Moderator mixing after a pressure tube failure

    International Nuclear Information System (INIS)

    MacKinnon, J.C.; Fortman, R.A.; Hadaller, G.I.

    1997-01-01

    During a guaranteed shutdown state (GSS) in a CANDU reactor, there must be sufficient negative reactivity to ensure subcriticality in the event of a process failure. In one of the acceptable states, the reactor is kept subcritical by a high concentration of a neutron-absorbing chemical (the poison gadolinium nitrate) dissolved in the moderator (i.e., the moderator is guaranteed overpoisoned). A postulated accident scenario which is considered as a part of reactor safety analysis is the rupture of a fuel channel (i.e., a pressure tube/calandria tube break) when the reactor is in a GSS. If one of the channels in the core breaks (requiring a simultaneous failure of both the pressure tube and the surrounding calandria tube), coolant from the primary heat transport system will be discharged into the moderator, causing an associated displacement of fluid through relief ducts at the top of the calandria vessel. The incoming (unpoisoned) coolant may mix quickly with the moderator, or may mix slowly while displacing poisoned moderator through the relief ducts. The effectiveness of mixing generally depends on the break location, the coolant discharge rate and the moderator circulation. If an in-core loss of coolant accident occurred while the reactor is in this overpoisoned state, it must be guaranteed that even with the dilution of the poison by the incoming coolant the reactor will remain subcritical on both a local and global basis. This paper presents an overview of an experimental program in progress at the Moderator Test Facility at Stern Laboratories to investigate coolant/poison mixing for a simulated in-core fishmouth pressure tube/calandria tube rupture. The nominal system conditions investigated are of a reactor in a GSS, with coolant in the primary heat transport system at the same temperature as the heavily poisoned moderator, i.e., a depressurised 'cold' state. The results presented are those obtained during the commissioning of the modified Test Facility. The

  7. Changes in unique hues induced by chromatic surrounds.

    Science.gov (United States)

    Klauke, Susanne; Wachtler, Thomas

    2016-03-01

    A chromatic surround can have a strong influence on the perceived hue of a stimulus. We investigated whether chromatic induction has similar effects on the perception of colors that appear pure and unmixed (unique red, green, blue, and yellow) as on other colors. Subjects performed unique hue settings of stimuli in isoluminant surrounds of different chromaticities. Compared with the settings in a neutral gray surround, unique hue settings altered systematically with chromatic surrounds. The amount of induced hue shift depended on the difference between stimulus and surround hues, and was similar for unique hue settings as for settings of nonunique hues. Intraindividual variability in unique hue settings was roughly twice as high as for settings obtained in asymmetric matching experiments, which may reflect the presence of a reference stimulus in the matching task. Variabilities were also larger with chromatic surrounds than with neutral gray surrounds, for both unique hue settings and matching of nonunique hues. The results suggest that the neural representations underlying unique hue percepts are influenced by the same neural processing mechanisms as the percepts of other colors.

  8. Evolution of paraffinic and naphtenic hydrocarbon and 3,4 benzopyrene content in mussels from a coastal zone polluted by a fuel spill

    Energy Technology Data Exchange (ETDEWEB)

    Bories, G; Tulliez, J; Peltier, J C; Fleckinger, R

    1969-05-03

    After an oil spill, a coastal zone was polluted and wild mussels were contaminated by paraffinic and naphtenic hydrocarbons and 3,4-benzopyrene. The evolution of this contamination was followed. Normal levels were re-established after a month and a half. Normal paraffins were metabolized faster than other hydrocarbons.

  9. Efficacy of paraffin bath therapy in hand osteoarthritis: a single-blinded randomized controlled trial.

    Science.gov (United States)

    Dilek, Banu; Gözüm, Mehtap; Şahin, Ebru; Baydar, Meltem; Ergör, Gül; El, Ozlem; Bircan, Çigdem; Gülbahar, Selmin

    2013-04-01

    To evaluate the efficacy of paraffin bath therapy on pain, function, and muscle strength in patients with hand osteoarthritis. Prospective single-blinded randomized controlled trial. Department of physical medicine and rehabilitation in a university hospital. Patients with bilateral hand osteoarthritis (N=56). Patients were randomized into 2 groups with a random number table by using block randomization with 4 patients in a block. Group 1 (n=29) had paraffin bath therapy (5 times per week, for 3-week duration) for both hands. Group 2 (n=27) was the control group. All patients were informed about joint-protection techniques, and paracetamol intake was recorded. The primary outcome measures were pain (at last 48h) at rest and during activities of daily living (ADL), assessed with a visual analog scale (0-10cm) at 12 weeks. The secondary outcome measures were the Australian Canadian Osteoarthritis Hand Index (AUSCAN) and the Dreiser Functional Index (DFI), used for subjective functional evaluation, loss of range of motion (ROM), grip and pinch strength, painful and tender joint counts, and paracetamol intake. A researcher blind to group allocation recorded the measures for both hands at baseline, 3 weeks, and 12 weeks at the hospital setting. At baseline, there were no significant differences between groups in any of the parameters (P>.05). After treatment, the paraffin group exhibited significant improvement in pain at rest and during ADL, ROM of the right hand, and pain and stiffness dimensions of the AUSCAN (P.05). The control group showed a significant deterioration in right hand grip and bilateral lateral pinch and right chuck pinch strength (Pparaffin group (Pparaffin group were significantly higher than the control group at 12 weeks (PParaffin bath therapy seemed to be effective both in reducing pain and tenderness and maintaining muscle strength in hand osteoarthritis. It may be regarded as a beneficial short-term therapy option, which is effective for a 12

  10. [Moderately haloalkaliphilic aerobic methylobacteria].

    Science.gov (United States)

    Trotsenko, Iu A; Doronina, N V; Li, Ts D; Reshetnikov, A S

    2007-01-01

    Aerobic methylobacteria utilizing oxidized and substituted methane derivatives as carbon and energy sources are widespread in nature and involved in the global carbon cycle, being a unique biofilter on the path of these C1 compounds from different ecosystems to the atmosphere. New data on the biological features of moderately halophilic, neutrophilic, and alkaliphilic methylobacteria isolated from biotopes with higher osmolarity (seas, saline and soda lakes, saline soils, and deteriorating marble) are reviewed. Particular attention is paid to the latest advances in the study of the mechanisms of osmoadaptation of aerobic moderately haloalkaliphilic methylobacteria: formation of osmolytes, in particular, molecular and genetic aspects of biosynthesis of the universal bioprotectant ectoine. The prospects for further studies of the physiological and biochemical principles of haloalkalophily and for the application of haloalkaliphilic aerobic methylobacteria in biosynthesis and biodegradation are discussed.

  11. Cold moderator scattering kernels

    International Nuclear Information System (INIS)

    MacFarlane, R.E.

    1989-01-01

    New thermal-scattering-law files in ENDF format have been developed for solid methane, liquid methane liquid ortho- and para-hydrogen, and liquid ortho- and para-deuterium using up-to-date models that include such effects as incoherent elastic scattering in the solid, diffusion and hindered vibration and rotations in the liquids, and spin correlations for the hydrogen and deuterium. These files were generated with the new LEAPR module of the NJOY Nuclear Data Processing System. Other modules of this system were used to produce cross sections for these moderators in the correct format for the continuous-energy Monte Carlo code (MCNP) being used for cold-moderator-design calculations at the Los Alamos Neutron Scattering Center (LANSCE). 20 refs., 14 figs

  12. Perspective for using Nd-Fe-B magnets as a tool for the improvement of the production and transportation of Vietnamese crude oil with high paraffin content

    International Nuclear Information System (INIS)

    Tung, N.P.; Vinh, N.Q.; Phong, N.T.P.; Long, B.Q.K.; Hung, P.V.

    2003-01-01

    Controlling the paraffin deposition is one of the most serious and costly problems for high-paraffin crude-oil production and transportation. This holds especially for offshore, deep-water wells and pipelines, like in Vietnam. For finding solutions for these problems, a series of experiments has been performed in order to study the effects of a magnetic field on the rheology of two often produced crude oil samples, using the high and variable magnetic-flux density of a Nd-Fe-B magnet. The resulting changes in the essential characteristics of the magnetically treated (MT) crude oils, like form and size of the paraffin clusters as well as the rheology parameters, have definitely proved the possibility to use a Nd-Fe-B magnetic tool as an environmentally friendly and effective method to control the paraffin deposition in crude oils of Vietnam that have a high paraffin content

  13. A design handbook for phase change thermal control and energy storage devices. [selected paraffins

    Science.gov (United States)

    Humphries, W. R.; Griggs, E. I.

    1977-01-01

    Comprehensive survey is given of the thermal aspects of phase change material devices. Fundamental mechanisms of heat transfer within the phase change device are discussed. Performance in zero-g and one-g fields are examined as it relates to such a device. Computer models for phase change materials, with metal fillers, undergoing conductive and convective processes are detailed. Using these models, extensive parametric data are presented for a hypothetical configuration with a rectangular phase change housing, using straight fins as the filler, and paraffin as the phase change material. These data are generated over a range of realistic sizes, material properties, and thermal boundary conditions. A number of illustrative examples are given to demonstrate use of the parametric data. Also, a complete listing of phase change material property data are reproduced herein as an aid to the reader.

  14. Dechlorination of short chain chlorinated paraffins by nanoscale zero-valent iron.

    Science.gov (United States)

    Zhang, Zhi-Yong; Lu, Mang; Zhang, Zhong-Zhi; Xiao, Meng; Zhang, Min

    2012-12-01

    In this study, nanoscale zero-valent iron (NZVI) particles were synthesized and used for the reductive dehalogenation of short chain chlorinated paraffins (SCCPs) in the laboratory. The results show that the dechlorination rate of chlorinated n-decane (CP(10)) by NZVI increased with decreased solution pH. Increasing the loading of NZVI enhanced the dechlorination rate of CP(10). With an increase in temperature, the degradation rate increased. The reduction of CP(10) by NZVI was accelerated with increasing the concentration of humic acid up to 15 mg/L but then was inhibited. The dechlorination of CP(10) within the initial 18 h followed pseudo-first order rate model. The formation of intermediate products indicates a stepwise dechlorination pathway of SCCPs by NZVI. The carbon chain length and chlorination degree of SCCPs have a polynominal impact on dechlorination reactions. Copyright © 2012 Elsevier B.V. All rights reserved.

  15. Cleanup of 7.5% tributyl phosphate/n-paraffin solvent-extraction solvent

    International Nuclear Information System (INIS)

    Reif, D.J.

    1987-02-01

    The HM process at the Savannah River Plant uses 7.5% tributyl phosphate in n-paraffin as an extraction solvent. During use, the solvent is altered due to hydrolysis and radiolysis, forming materials which influence product losses, product decontamination, and separation efficiencies. Laboratory studies to improve online solvent cleaning have shown that carbonate washing, although removing residual solvent activity, does not remove binding ligands which hold fission products in the solvent. Treatment of solvent by an alumina adsorption process removes binding ligands and significantly improves recycle solvent performance. Both laboratory work defining a full-scale alumina adsorption process and the use of the process to clean HM process first cycle solvent is discussed

  16. Terahertz spectroscopy for the study of paraffin-embedded gastric cancer samples

    Science.gov (United States)

    Wahaia, Faustino; Kasalynas, Irmantas; Seliuta, Dalius; Molis, Gediminas; Urbanowicz, Andrzej; Carvalho Silva, Catia D.; Carneiro, Fatima; Valusis, Gintaras; Granja, Pedro L.

    2015-01-01

    Terahertz (THz) spectroscopy constitute promising technique for biomedical applications as a complementary and powerful tool for diseases screening specially for early cancer diagnostic. The THz radiation is not harmful to biological tissues. As increased blood supply in cancer-affected tissues and consequent local increase in tissue water content makes THz technology a potentially attractive. In the present work, samples of healthy and adenocarcinoma-affected gastric tissue were analyzed using transmission time-domain THz spectroscopy (THz-TDS). The work shows the capability of the technique to distinguish between normal and cancerous regions in dried and paraffin-embedded samples. Plots of absorption coefficient α and refractive index n of normal and cancer affected tissues, are presented and the conditions for discrimination between normal and affected tissues are discussed.

  17. Separation of Olefin/Paraffin Mixtures with Carrier Facilitated Membrane Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Merkel, T.C.; Blanc, R.; Zeid, J.; Suwarlim, A.; Firat, B.; Wijmans, H.; Asaro, M. (SRI); Greene, M.(Lummus)

    2007-03-12

    This document describes the results of a DOE funded joint effort of Membrane Technology and Research Inc. (MTR), SRI International (SRI), and ABB Lummus (ABB) to develop facilitated transport membranes for olefin/paraffin separations. Currently, olefin/paraffin separation is done by distillation—an extremely energy-intensive process because of the low relative volatilities of olefins and paraffins. If facilitated transport membranes could be successfully commercialized, the potential energy savings achievable with this membrane technology are estimated to be 48 trillion Btu per year by the year 2020. We discovered in this work that silver salt-based facilitated transport membranes are not stable even in the presence of ideal olefin/paraffin mixtures. This decline in membrane performance appears to be caused by a previously unrecognized phenomenon that we have named olefin conditioning. As the name implies, this mechanism of performance degradation becomes operative once a membrane starts permeating olefins. This project is the first study to identify olefin conditioning as a significant factor impacting the performance of facilitated olefin transport membranes. To date, we have not identified an effective strategy to mitigate the impact of olefin conditioning. other than running at low temperatures or with low olefin feed pressures. In our opinion, this issue must be addressed before further development of facilitated olefin transport membranes can proceed. In addition to olefin conditioning, traditional carrier poisoning challenges must also be overcome. Light, hydrogen, hydrogen sulfide, and acetylene exposure adversely affect membrane performance through unwanted reaction with silver ions. Harsh poisoning tests with these species showed useful membrane lifetimes of only one week. These tests demonstrate a need to improve the stability of the olefin complexing agent to develop membranes with lifetimes satisfactory for commercial application. A successful effort

  18. Method and equipment to utilize solar heat. [paraffin used as heat storage material

    Energy Technology Data Exchange (ETDEWEB)

    Poellein, H

    1976-09-16

    In this process, solar radiation is converted into heat by means of absorbers. The heat transferred to a liquid is led in forced circulation, first into a heat storage device and then into a water heater. The cooled-down liquid is rercirculated. The storage material used here is paraffin. A measuring and control device is provided to switch from periods with solar radiation to periods where only stored energy is consumed. This device consists of a photocell measuring the incoming sunlight and a temperarure sensor. The control system is put into operation by a combination of the two measured values. The heat accumulator consists of several elements connected in parallel. A control device makes sure that only one accumulator element at a time is part of the circuit. The absorbers, as usual, consists of the absorber plate proper and a cover plate.

  19. Melting/solidification characteristics of paraffin based nanocomposite for thermal energy storage applications

    Directory of Open Access Journals (Sweden)

    Lokesh Selvam

    2017-01-01

    Full Text Available The present work aimed to investigate the melting and solidification characteristics of nanoparticle enhanced phase change material (NEPCM. The NEPCM were prepared using paraffin as the phase change material and multiwall carbon nanotube (MWCNT as the nanomaterial without using any dispersant. Thermal conductivity of the NEPCM was measured with respect to temperature and the measured data showed higher enhancement than the phase change material both in liquid and solid state, due to inherent high conductive and the continuous networking of the MWCNT. A reduction in solidification and melting time of 42% and 29% was achieved in the case of NEPCM with 0.9% and 0.3%, respectively. It is concluded that enhanced heat transfer characteristics of NEPCM is highly beneficial towards design and development of efficient thermal energy storage system for various applications.

  20. New hybrid nanofluid containing encapsulated paraffin wax and sand nanoparticles in propylene glycol-water mixture: Potential heat transfer fluid for energy management

    International Nuclear Information System (INIS)

    Manikandan, S.; Rajan, K.S.

    2017-01-01

    Highlights: • Hybrid nanofluid containing sand nanoparticles & encapsulated paraffin wax prepared. • Specific heat of hybrid nanofluid 9% greater than that of PG-water mixture. • Specific heat & thermal conductivity enhanced at optimum paraffin wax concentration. • Hybrid nanofluid with 1 wt.% paraffin wax & 1 vol% sand nanoparticles best suited. - Abstract: The reduction in specific heat commonly encountered due to the addition of nanoparticles to a heat transfer fluid such as propylene glycol-water mixture, can be overcome by co-dispersing surfactant-encapsulated paraffin wax, leading to formation of a hybrid nanofluid. Experimental investigations have been carried out on the preparation and evaluation of thermophysical properties of a hybrid nanofluid containing pluronic P-123 encapsulated paraffin wax (70–120 nm diameter, 1–5 wt.%) and sand nanoparticles (1 vol%) in propylene glycol-water mixture. The comparison of results of differential scanning calorimetry of pure paraffin wax and encapsulated paraffin wax revealed encapsulation efficiency of 84.4%. The specific heat of hybrid nanofluids monotonously increased with paraffin wax concentration, with 9.1% enhancement in specific heat for hybrid nanofluid containing 5 wt.% paraffin wax, in comparison to propylene glycol-water mixture. There exists an optimum paraffin wax concentration (1 wt.%) for the hybrid nanofluid at which the combination of various thermophysical properties such as specific heat, thermal conductivity and viscosity are favorable for use as heat transfer fluid. Such a hybrid nanofluid can be used as a substitute for propylene glycol-water mixture in solar thermal systems.

  1. Recent developments in capabilities for analysing chlorinated paraffins in environmental matrices: A review.

    Science.gov (United States)

    van Mourik, Louise M; Leonards, Pim E G; Gaus, Caroline; de Boer, Jacob

    2015-10-01

    Concerns about the high production volumes, persistency, bioaccumulation potential and toxicity of chlorinated paraffin (CP) mixtures, especially short-chain CPs (SCCPs), are rising. However, information on their levels and fate in the environment is still insufficient, impeding international classifications and regulations. This knowledge gap is mainly due to the difficulties that arise with CP analysis, in particular the chromatographic separation within CPs and between CPs and other compounds. No fully validated routine analytical method is available yet and only semi-quantitative analysis is possible, although the number of studies reporting new and improved methods have rapidly increased since 2010. Better cleanup procedures that remove interfering compounds, and new instrumental techniques, which distinguish between medium-chain CPs (MCCPs) and SCCPs, have been developed. While gas chromatography coupled to an electron capture negative ionisation mass spectrometry (GC/ECNI-MS) remains the most commonly applied technique, novel and promising use of high resolution time of flight MS (TOF-MS) has also been reported. We expect that recent developments in high resolution TOF-MS and Orbitrap technologies will further improve the detection of CPs, including long-chain CPs (LCCPs), and the group separation and quantification of CP homologues. Also, new CP quantification methods have emerged, including the use of mathematical algorithms, multiple linear regression and principal component analysis. These quantification advancements are also reflected in considerably improved interlaboratory agreements since 2010. Analysis of lower chlorinated paraffins (

  2. DNA degrades during storage in formalin-fixed and paraffin-embedded tissue blocks.

    Science.gov (United States)

    Guyard, Alice; Boyez, Alice; Pujals, Anaïs; Robe, Cyrielle; Tran Van Nhieu, Jeanne; Allory, Yves; Moroch, Julien; Georges, Odette; Fournet, Jean-Christophe; Zafrani, Elie-Serge; Leroy, Karen

    2017-10-01

    Formalin-fixed paraffin-embedded (FFPE) tissue blocks are widely used to identify clinically actionable molecular alterations or perform retrospective molecular studies. Our goal was to quantify degradation of DNA occurring during mid to long-term storage of samples in usual conditions. We selected 46 FFPE samples of surgically resected carcinomas of lung, colon, and urothelial tract, of which DNA had been previously extracted. We performed a second DNA extraction on the same blocks under identical conditions after a median period of storage of 5.5 years. Quantitation of DNA by fluorimetry showed a 53% decrease in DNA quantity after storage. Quantitative PCR (qPCR) targeting KRAS exon 2 showed delayed amplification of DNA extracted after storage in all samples but one. The qPCR/fluorimetry quantification ratio decreased from 56 to 15% after storage (p DNA analyzable by qPCR represented only 11% of the amount obtained at first extraction. Maximal length of amplifiable DNA fragments assessed with a multiplex PCR was reduced in DNA extracted from stored tissue, indicating that DNA fragmentation had increased in the paraffin blocks during storage. Next-generation sequencing was performed on 12 samples and showed a mean 3.3-fold decrease in library yield and a mean 4.5-fold increase in the number of single-nucleotide variants detected after storage. In conclusion, we observed significant degradation of DNA extracted from the same FFPE block after 4 to 6 years of storage. Better preservation strategies should be considered for storage of FFPE biopsy specimens.

  3. Superresolution Imaging of Aquaporin-4 Cluster Size in Antibody-Stained Paraffin Brain Sections.

    Science.gov (United States)

    Smith, Alex J; Verkman, Alan S

    2015-12-15

    The water channel aquaporin-4 (AQP4) forms supramolecular clusters whose size is determined by the ratio of M1- and M23-AQP4 isoforms. In cultured astrocytes, differences in the subcellular localization and macromolecular interactions of small and large AQP4 clusters results in distinct physiological roles for M1- and M23-AQP4. Here, we developed quantitative superresolution optical imaging methodology to measure AQP4 cluster size in antibody-stained paraffin sections of mouse cerebral cortex and spinal cord, human postmortem brain, and glioma biopsy specimens. This methodology was used to demonstrate that large AQP4 clusters are formed in AQP4(-/-) astrocytes transfected with only M23-AQP4, but not in those expressing only M1-AQP4, both in vitro and in vivo. Native AQP4 in mouse cortex, where both isoforms are expressed, was enriched in astrocyte foot-processes adjacent to microcapillaries; clusters in perivascular regions of the cortex were larger than in parenchymal regions, demonstrating size-dependent subcellular segregation of AQP4 clusters. Two-color superresolution imaging demonstrated colocalization of Kir4.1 with AQP4 clusters in perivascular areas but not in parenchyma. Surprisingly, the subcellular distribution of AQP4 clusters was different between gray and white matter astrocytes in spinal cord, demonstrating regional specificity in cluster polarization. Changes in AQP4 subcellular distribution are associated with several neurological diseases and we demonstrate that AQP4 clustering was preserved in a postmortem human cortical brain tissue specimen, but that AQP4 was not substantially clustered in a human glioblastoma specimen despite high-level expression. Our results demonstrate the utility of superresolution optical imaging for measuring the size of AQP4 supramolecular clusters in paraffin sections of brain tissue and support AQP4 cluster size as a primary determinant of its subcellular distribution. Copyright © 2015 Biophysical Society

  4. Nylon filament coated with paraffin for intraluminal permanent middle cerebral artery occlusion in rats.

    Science.gov (United States)

    Zuo, Xia-Lin; Wu, Ping; Ji, Ai-Min

    2012-06-21

    A variety of intraluminal nylon filament has been used in rat middle cerebral artery occlusion (MCAO) models. However the lesion extent and its reproducibility vary among laboratories. The properties of nylon filament play a part of reasons for these variations. In the present study, we used paraffin-coated nylon filament for rat MCAO model, tested the effects and advanced improvement for making the rat MCAO. Forty male Sprague-Dawley (SD) rats were randomized into two groups, MCAO with traditional uncoated nylon filament (uMCAO) and MCAO with paraffin-coated nylon filament (cMCAO), three rats as normal group and sham group respectively. Assessment included mortality rates, model success rates, neurological deficit evaluation, and infarct volume. The study showed two rats died in uMCAO group, no rat died in cMCAO group within the 12h. The model success rate of uMCAO was 100%, while the uMCAO group was 55% (n=20, two died within 12h, seven rats were excluded as the brain slices showed no TTC staining due to subarachanoid hemorrhage). Neurological evaluation demonstrated group cMCAO had more worse neurological outcomes than group uMCAO, and the difference was statistically signification (pparaffin-coated nylon filament intraluminal occlusion provide better occlusion of middle cerebral artery than the uncoated nylon filament, improve the consistent of model, and raise the success rate to reduce the number of experimental animals. These positive results are much encouraging and interesting. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

  5. An unusual delayed complication of paraffin self-injection for penile girth augmentation.

    Science.gov (United States)

    De Siati, Mario; Selvaggio, Oscar; Di Fino, Giuseppe; Liuzzi, Giuseppe; Massenio, Paolo; Sanguedolce, Francesca; Carrieri, Giuseppe; Cormio, Luigi

    2013-12-01

    Penile self-injection of various oils is still carried out among Eastern Europe people for penile girth augmentation despite the potential destructive complications of this practice are well known. Penile reactions to such foreign bodies include scarring, abscess formation, ulceration, and even Fournier's gangrene; voiding problems due to mineral oil self-injection have been reported only once. To our knowledge, we describe the first case of paraffin self-injection for penile girth augmentation presenting with acute urinary retention. A 27-year-old Romanian man presented with severe penile pain and acute urinary retention five years after having practiced repeated penile self-injections of paraffin for penile girth augmentation. The penile shaft was massively enlarged, fibrotic and phymotic; urethral catheterization failed due to severe stricture of the proximal pendulum urethra. The patients refused placement of a suprapubic catheter and underwent immediate penile surgical exploration. The scarred tissue between dartos and Buck's fascia and a fibrotic ring occluding the urethra were removed and the penile skin reconstructed. Pathology confirmed the diagnosis of paraffinoma. The patient resumed normal voiding immediately after catheter removal on second postoperative day; he was very pleased with cosmetic, sexual and voiding results at six weeks, six months and 1 year follow-up. The present report describes a novel complication of penile self-injection for penile girth augmentation. Because of the increasing number of patients seeking penile augmentation, physicians dealing with sexual medicine should pay more attention to such request to prevent the use of non medical treatments that can turn into medical disasters.

  6. Cellular localization of 2-[3H]deoxy-D-glucose from paraffin-embedded brains

    International Nuclear Information System (INIS)

    Durham, D.; Woolsey, T.A.; Kruger, L.

    1981-01-01

    Results of experiments in which regional neuronal activity is revealed by a 2-[ 3 H]deoxy-D-glucose ( 3 H-2-DG)-paraffin section-emulsion autoradiography method are described. The trigeminal pathway of freely behaving mice was activated differentially by selective patterns of whisker removal. One hour after injection of concentrated 3 H-2-DG, the animals were perfused systemically with a periodate/lysine/paraformaldehyde mixture the brains were embedded in paraffin, and serial sections were taken and coated with emulsion for autoradiography. Diffusion of the isotope out of the tissue was assessed visually and by liquid scintillation counting. While substantial loss of 3 H isotope into the embedding fluids (about 95%) was found, the scintillation counts and the autoradiograms showed good fixation of the isotope in situ, no evidence of isotope movement into the emulsion, and no gradients of diffusion in the sectioned material. Patterns of regional labeling were similar to those reported from brains prepared by conventional 2-[ 14 C]deoxy-D-glucose ( 14 C-2-DG) autoradiography; Trigeminal structures associated with the intact (stimulated) whiskers were labeled relatively heavily, indicating that label uptake is specific with respect to neuronal activity. In the cortex, the patterns of label corresponded directly and precisely to those barrels known to receive inputs from the intact whiskers. Distribution of silver grains in the cortex and in the brainstem was correlated directly with neuronal profiles. Clearly, this approach offers considerable technical advantages, in particular, the ease with which the histological material is prepared. The resolution of the autoradiograms and the quality of the histology are excellent

  7. Light microscopic identification and semiquantification of polyethylene particles in methylmethacrylate and paraffin-embedded experimental bone implant specimens

    DEFF Research Database (Denmark)

    Rahbek, O; Kold, S; Overgaard, S

    2005-01-01

    The aim of this study was to evaluate the identification of polyethylene (PE) particles in relatively thick methylmethacrylate (MMA) sections widely used in bone implant research. The sensitivity and specificity were compared between decalcified paraffin-embedded oil red O (ORO) stained and MMA-e...

  8. Limited numbers of apoptotic cells in fresh paraffin embedded bone marrow samples of patients with myelodysplastic syndrome

    NARCIS (Netherlands)

    Brada, SJL; van de Loosdrecht, AA; Koudstaal, J; de Wolf, JTM; Vellenga, E

    In myelodysplasia (MDS) the precise mechanism of ineffective erythropoiesis is not fully elucidated, but it is suggested that apoptosis may contribute to this process. We performed TdT-mediated dUTP-nick end labelling (TUNEL) staining of paraffin embedded bone marrow specimens to assess the amount

  9. New comprehensive denaturing-gradient-gel-electrophoresis assay for KRAS mutation detection applied to paraffin-embedded tumours

    NARCIS (Netherlands)

    Hayes, VM; Westra, JL; Verlind, E; Bleeker, W; Plukker, JT; Hofstra, RMW; Buys, CHCM

    2000-01-01

    A comprehensive mutation detection assay is presented for the entire coding region and all splice site junctions of the KRAS oncogene. The assay is based on denaturing gradient gel electrophoresis and applicable to archival paraffin-embedded tumour material. All KRAS amplicons are analysed within

  10. Investigation of archived formalin-fixed paraffin-embedded pancreatic tissue with whole-genome gene expression microarray

    DEFF Research Database (Denmark)

    Michelsen, Nete Vinstrup; Brusgaard, Klaus; Tan, Qihua

    2011-01-01

    The use of formalin-fixed, paraffin-embedded (FFPE) tissue overcomes the most prominent issues related to research on relatively rare diseases: limited sample size, availability of control tissue, and time frame. The use of FFPE pancreatic tissue in GEM may be especially challenging due to its very...

  11. Using Paraffin PCM, Cryogel and TEC to Maintain Comet Surface Sample Cold from Earth Approach Through Retrieval

    Science.gov (United States)

    Choi, Michael K.

    2017-01-01

    An innovative thermal design concept to maintain comet surface samples cold (for example, 263 degrees Kelvin, 243 degrees Kelvin or 223 degrees Kelvin) from Earth approach through retrieval is presented. It uses paraffin phase change material (PCM), Cryogel insulation and thermoelectric cooler (TEC), which are commercially available.

  12. Comparing the proteome of snap frozen, RNAlater preserved, and formalin-fixed paraffin-embedded human tissue samples

    DEFF Research Database (Denmark)

    Bennike, Tue Bjerg; Kastaniegaard, Kenneth; Padurariu, Simona

    2016-01-01

    Large biobanks exist worldwide containing formalin-fixed, paraffin-embedded samples and samples stored in RNAlater. However, the impact of tissue preservation on the result of a quantative proteome analysis remains poorly described.Human colon mucosal biopsies were extracted from the sigmoideum...

  13. Dose-Response Analysis of RNA-Seq Profiles in Archival Formalin-Fixed Paraffin-Embedded (FFPE) Samples.

    Science.gov (United States)

    Use of archival resources has been limited to date by inconsistent methods for genomic profiling of degraded RNA from formalin-fixed paraffin-embedded (FFPE) samples. RNA-sequencing offers a promising way to address this problem. Here we evaluated transcriptomic dose responses us...

  14. Quantitative PCR for HTLV-1 provirus in adult T-cell leukemia/lymphoma using paraffin tumor sections.

    Science.gov (United States)

    Kato, Junki; Masaki, Ayako; Fujii, Keiichiro; Takino, Hisashi; Murase, Takayuki; Yonekura, Kentaro; Utsunomiya, Atae; Ishida, Takashi; Iida, Shinsuke; Inagaki, Hiroshi

    2016-11-01

    Detection of HTLV-1 provirus using paraffin tumor sections may assist the diagnosis of adult T-cell leukemia/lymphoma (ATLL). For the detection, non-quantitative PCR assay has been reported, but its usefulness and limitations remain unclear. To our knowledge, quantitative PCR assay using paraffin tumor sections has not been reported. Using paraffin sections from ATLLs and non-ATLL T-cell lymphomas, we first performed non-quantitative PCR for HTLV-1 provirus. Next, we determined tumor ratios and carried out quantitative PCR to obtain provirus copy numbers. The results were analyzed with a simple regression model and a novel criterion, cut-off using 95 % rejection limits. Our quantitative PCR assay showed an excellent association between tumor ratios and the copy numbers (r = 0.89, P paraffin tumor sections may be useful for the screening of ATLL cases, especially in HTLV-1 non-endemic areas where easy access to serological testing for HTLV-1 infection is limited. © 2016 Japanese Society of Pathology and John Wiley & Sons Australia, Ltd.

  15. Relative shrinkage of adipocytes by paraffin in proportion to plastic embedding in human adipose tissue before and after weight loss.

    Science.gov (United States)

    Verhoef, Sanne P M; van Dijk, Paul; Westerterp, Klaas R

    2013-01-01

    Adipocyte size is a major modulator of endocrine functioning of adipose tissue and methods allowing accurate determination of adipocyte size are important to study energy metabolism. The aim of this study was to assess the relative shrinkage of adipocytes before and after weight loss by comparing adipose tissue from the same subjects embedded in paraffin and plastic. 18 healthy subjects (5 males and 13 females) aged 20-50 y with a BMI of 28-38 kg/m² followed a very low energy diet for 8 weeks. Adipose tissue biopsies were taken prior to and after weight loss and were processed for paraffin and plastic sections. Parameters of adipocyte size were determined with computer image analysis. Mean adipocyte size was smaller in paraffin compared to plastic embedded tissue both before (66 ± 4 vs. 103 ± 5 μm, P paraffin embedded tissue in proportion to plastic embedded tissue was not significantly different before and after weight loss (73 and 69%, respectively). Shrinkage due to the type of embedding of the adipose tissue can be ignored when comparing before and after weight loss. Plastic embedding of adipose tissue provides more accurate and sensitive results. © 2013 Asian Oceanian Association for the Study of Obesity . Published by Elsevier Ltd. All rights reserved.

  16. Magnetism and Microwave Absorption Properties of Fe3O4 Microflake-Paraffin Composites Without and With Magnetic Orientation

    Science.gov (United States)

    Wang, Peng; Zhang, Junming; Chen, Yuanwei; Wang, Guowu; Wang, Dian; Wang, Tao; Li, Fashen

    2018-01-01

    We have synthesized thin Fe3O4 microflakes by a simple hydrothermal method and prepared Fe3O4 microflake-paraffin composites without and with magnetic orientation using the method of simple ultrasonic mixing and rotating samples in a magnetic field. X-ray diffractometer, Mössbauer spectrum, scanning electron microscope and vibrating sample magnetometer were used to characterize the samples. The complex permittivity and permeability of Fe3O4 microflake-paraffin composites without and with magnetic orientation were measured in the frequency range of 0.1-18 GHz by a vector network analyzer using a coaxial method. The reflection loss (RL) was calculated by the measured electromagnetic parameters using transmission line theory. The measurement of electromagnetic parameters shows that magnetic orientation makes the complex permittivity and permeability increase. The calculated RL shows that the Fe3O4 microflake-paraffin composite with magnetic orientation has enhanced microwave absorption properties in the frequency range of 1-3 GHz and the thickness range of 2.9-3.5 mm, indicating that the Fe3O4 microflake-paraffin composite with magnetic orientation is a promising thin microwave absorption material in the L-S band.

  17. The heat storage material based on paraffin-modified multilayer carbon nanotubes with Nickel-zinc ferrite

    Science.gov (United States)

    Shchegolkov, A.; Shchegolkov, A.; Dyachkova, T.; Semenov, A.

    2018-02-01

    The paper presents an investigation of magnetically controlled heat-storage material based on paraffin, modified with multilayer carbon nanotubes with nickel-zinc ferrite. The technology of obtaining nanomodified material capable of interacting with magnetic field is presented. The study of the heat-exchange processes of charge/discharge with the help of magnetic field are carried out.

  18. A synchronous surround increases the motion strength gain of motion.

    Science.gov (United States)

    Linares, Daniel; Nishida, Shin'ya

    2013-11-12

    Coherent motion detection is greatly enhanced by the synchronous presentation of a static surround (Linares, Motoyoshi, & Nishida, 2012). To further understand this contextual enhancement, here we measured the sensitivity to discriminate motion strength for several pedestal strengths with and without a surround. We found that the surround improved discrimination of low and medium motion strengths, but did not improve or even impaired discrimination of high motion strengths. We used motion strength discriminability to estimate the perceptual response function assuming additive noise and found that the surround increased the motion strength gain, rather than the response gain. Given that eye and body movements continuously introduce transients in the retinal image, it is possible that this strength gain occurs in natural vision.

  19. Surrounding Moving Obstacle Detection for Autonomous Driving Using Stereo Vision

    Directory of Open Access Journals (Sweden)

    Hao Sun

    2013-06-01

    Full Text Available Detection and tracking surrounding moving obstacles such as vehicles and pedestrians are crucial for the safety of mobile robotics and autonomous vehicles. This is especially the case in urban driving scenarios. This paper presents a novel framework for surrounding moving obstacles detection using binocular stereo vision. The contributions of our work are threefold. Firstly, a multiview feature matching scheme is presented for simultaneous stereo correspondence and motion correspondence searching. Secondly, the multiview geometry constraint derived from the relative camera positions in pairs of consecutive stereo views is exploited for surrounding moving obstacles detection. Thirdly, an adaptive particle filter is proposed for tracking of multiple moving obstacles in surrounding areas. Experimental results from real-world driving sequences demonstrate the effectiveness and robustness of the proposed framework.

  20. Contamination of nebulisers and surrounding air at the bedside of ...

    African Journals Online (AJOL)

    An air sampler was used to collect air samples from the surrounding bedside environment. .... individualised resealable plastic bags and stored upside down in a cooler .... conventional and mesh technology nebulisers used at home by adults.

  1. Glow phenomenon surrounding the vertical stabilizer and OMS pods

    Science.gov (United States)

    1994-01-01

    This 35mm frame, photographed as the Space Shuttle Columbia was orbiting Earth during a 'night' pass, documents the glow phenomenon surrounding the vertical stabilizer and the Orbital Maneuvering System (OMS) pods of the spacecraft.

  2. Drivers and moderators of business decline

    Directory of Open Access Journals (Sweden)

    Marius Pretorius

    2010-12-01

    Full Text Available Purpose: Reports of business failure elicit various reactions, while research in this domain often appears to be limited by a lack of access to information about failure and by the negativity that surrounds it. Those who have experienced failure do not readily talk about it, or they disappear from the radar screen of researchers. Yet failure is preceded by decline which, when focused on strategically, can reduce eventual failures if early action is taken. The main purpose of this study is to develop a conceptual framework or typology of the drivers and moderators of business decline. Design/methodology/approach: After applying the "grounded theory" approach to the academic literature on decline and failure, a conceptual framework for the variables that drive and moderate business decline is proposed. Findings: The study proposes that decline has three core drivers, three peripheral drivers and four moderators. The core drivers identified are: resource munificence; leadership as origin; and causality (strategic versus operational origin of decline. The three peripheral drivers are: unique preconditions; continuous decisions impact; and extremes dichotomy. The study describes four moderators of the drivers: life cycle stage; stakeholder perspective; quantitative versus qualitative nature of signs and causes; and finally the age and size effects. Research limitations/implications: The proposed conceptual framework is based on literature only, although it has found support during discussions with practitioners. It is proposed to readers of this journal for scrutiny and validation. Practical implications: Strategists need to understand what drives decline in order to act timeously; practitioners who have an insight into the moderators with their impacts could make better decisions in response to decline in organisations and possibly avoid business failure. Originality/Value: Understanding business decline is still a huge theoretical challenge, which

  3. Multiplexed color-coded probe-based gene expression assessment for clinical molecular diagnostics in formalin-fixed paraffin-embedded human renal allograft tissue.

    Science.gov (United States)

    Adam, Benjamin; Afzali, Bahman; Dominy, Katherine M; Chapman, Erin; Gill, Reeda; Hidalgo, Luis G; Roufosse, Candice; Sis, Banu; Mengel, Michael

    2016-03-01

    Histopathologic diagnoses in transplantation can be improved with molecular testing. Preferably, molecular diagnostics should fit into standard-of-care workflows for transplant biopsies, that is, formalin-fixed paraffin-embedded (FFPE) processing. The NanoString(®) gene expression platform has recently been shown to work with FFPE samples. We aimed to evaluate its methodological robustness and feasibility for gene expression studies in human FFPE renal allograft samples. A literature-derived antibody-mediated rejection (ABMR) 34-gene set, comprised of endothelial, NK cell, and inflammation transcripts, was analyzed in different retrospective biopsy cohorts and showed potential to molecularly discriminate ABMR cases, including FFPE samples. NanoString(®) results were reproducible across a range of RNA input quantities (r = 0.998), with different operators (r = 0.998), and between different reagent lots (r = 0.983). There was moderate correlation between NanoString(®) with FFPE tissue and quantitative reverse transcription polymerase chain reaction (qRT-PCR) with corresponding dedicated fresh-stabilized tissue (r = 0.487). Better overall correlation with histology was observed with NanoString(®) (r = 0.354) than with qRT-PCR (r = 0.146). Our results demonstrate the feasibility of multiplexed gene expression quantification from FFPE renal allograft tissue. This represents a method for prospective and retrospective validation of molecular diagnostics and its adoption in clinical transplantation pathology. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  4. An experimental investigation of heat transfer from a reactor fuel channel to surrounding water

    International Nuclear Information System (INIS)

    Gillespie, G.E.

    An important feature of the CANDU-PHW reactor is that each fuel channel is surrounded by cool heavy-water moderator that can act as a sink for heat generated in the fuel if other means of heat removal were to fail. During postulated loss-of-coolant accidents there are two scenarios in which the primary cooling system may not prevent fuel-channel overheating. These situations arise when: (1) for a particular break size and location, called the critical break, the coolant flow through a portion of the reactor core stagnates before the emergency coolant injection system restores circulation, or, (2) the emergency coolant injection system fails to operate. In either case, the heat generated in the fuel is transferred mainly by radiation to the pressure tube and calandria tube, and then by boiling heat transfer to the moderator. This paper describes a simple one-dimensional model developed to analyse the thermal behaviour of a fuel channel when the internal pressure is high. Also described is a series of experiments in which the pressure-tube segment is pressurized and heated at a constant rate until it contacts a surrounding calandria-tube segment. Predictions of the one-dimensional model are compared with the experimental results

  5. Monitoring program of surrounding of the NPP SE-EBO

    International Nuclear Information System (INIS)

    Dobis, L.; Kostial, J.

    1997-01-01

    The paper dealt with monitoring program of radiation control of surrounding of the NPP Bohunice, which has the aim: (1) to ensure the control of influence of work of the NPP Bohunice on the environment in their surrounding; (2) to ensure the back-ground for regular brief of control and supervisory organs about condition of the environment in surrounding of the NPP Bohunice; (3) to maintain the expected technical level of control of the NPP Bohunice and to exploit optimally the technical means; (4) to solicit permanently the data about the radioactivity of environment in surrounding of the NPP Bohunice for forming of files of the data; (5) to exploit purposefully the technical equipment, technical workers and to maintain their in permanent emergency and technical eligibility for the case of the breakdown; (6) to obtain permanently the files of the values for qualification of the reference levels. This program of monitoring includes the radiation control of surrounding of the NPP Bohunice, in the time of normal work of power-station's blocks, inclusively of all types of trouble-shooting and repairer works in surrounding of the NPP Bohunice, up to distance 20 km from power-station. The monitoring includes: outlets from the NPP Bohunice, monitoring of radiation characteristics in surrounding of the NPP Bohunice, (aerosols, fall-outs, soil), the links of food chains: (grass and fodder, milk, agriculture products), hydrosphere in surrounding (surface waters, drink water, bores of radiation control in complex of the NPP Bohunice, components of the hydrosphere), measurement of radiation from external sources (measurement of the dose rates, measurement of the doses [sk

  6. Chromatic induction from surrounding stimuli under perceptual suppression.

    Science.gov (United States)

    Horiuchi, Koji; Kuriki, Ichiro; Tokunaga, Rumi; Matsumiya, Kazumichi; Shioiri, Satoshi

    2014-11-01

    The appearance of colors can be affected by their spatiotemporal context. The shift in color appearance according to the surrounding colors is called color induction or chromatic induction; in particular, the shift in opponent color of the surround is called chromatic contrast. To investigate whether chromatic induction occurs even when the chromatic surround is imperceptible, we measured chromatic induction during interocular suppression. A multicolor or uniform color field was presented as the surround stimulus, and a colored continuous flash suppression (CFS) stimulus was presented to the dominant eye of each subject. The subjects were asked to report the appearance of the test field only when the stationary surround stimulus is invisible by interocular suppression with CFS. The resulting shifts in color appearance due to chromatic induction were significant even under the conditions of interocular suppression for all surround stimuli. The magnitude of chromatic induction differed with the surround conditions, and this difference was preserved regardless of the viewing conditions. The chromatic induction effect was reduced by CFS, in proportion to the magnitude of chromatic induction under natural (i.e., no-CFS) viewing conditions. According to an analysis with linear model fitting, we revealed the presence of at least two kinds of subprocesses for chromatic induction that reside at higher and lower levels than the site of interocular suppression. One mechanism yields different degrees of chromatic induction based on the complexity of the surround, which is unaffected by interocular suppression, while the other mechanism changes its output with interocular suppression acting as a gain control. Our results imply that the total chromatic induction effect is achieved via a linear summation of outputs from mechanisms that reside at different levels of visual processing.

  7. Lead identification in soil surrounding a used lead acid battery smelter area in Banten, Indonesia

    International Nuclear Information System (INIS)

    Adventini, N; Santoso, M; Lestiani, D D; Syahfitri, W Y N; Rixson, L

    2017-01-01

    A used lead acid battery smelter generates particulates containing lead that can contaminate the surrounding environment area. Lead is a heavy metal which is harmful to health if it enters the human body through soil, air, or water. An identification of lead in soil samples surrounding formal and informal used lead acid battery smelters area in Banten, Indonesia using EDXRF has been carried out. The EDXRF accuracy and precision evaluated from marine sediment IAEA 457 gave a good agreement to the certified value. A number of 16 soil samples from formal and informal areas and 2 soil samples from control area were taken from surface and subsurface soils. The highest lead concentrations from both lead smelter were approximately 9 folds and 11 folds higher than the reference and control samples. The assessment of lead contamination in soils described in C f index was in category: moderately and strongly polluted by lead for formal and informal lead smelter. Daily lead intake of children in this study from all sites had exceeded the recommended dietary allowance. The HI values for adults and children living near both lead smelter areas were greater than the value of safety threshold 1. This study finding confirmed that there is a potential health risk for inhabitants surrounding the used lead acid battery smelter areas in Banten, Indonesia. (paper)

  8. Interaction study of polyisobutylene with paraffins by NMR using the evaluation of spin-lattice relaxation times for hydrogen nuclei; Estudo da interacao do poliisobutileno com parafinas por RMN no estado solido

    Energy Technology Data Exchange (ETDEWEB)

    Marques, Rosana G.G. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas - CENPES]. E-mail: garrido@cenpes.petrobras.com.br; Tavares, Maria I.B. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Inst. de Macromoleculas]. E-mail: mibt@ima.ufrj.br

    2001-07-01

    The evaluation of spin-lattice relaxation times of {sup 1}H for polyisobutylene/paraffin systems, were obtained using the classic inversion recovery technique, and also through Cross Polarization Magic Angle Spinning (CP/MAS) techniques varying the contact time and also by the delayed contact time pulse sequence. NMR results showed that the polyisobutylene/paraffin systems in which high molecular weight paraffins were used, is heterogeneous. However, for paraffins with low molecular weight, the system presents good homogeneity. (author)

  9. In vitro and in vivo MMP gene expression localisation by In Situ-RT-PCR in cell culture and paraffin embedded human breast cancer cell line xenografts

    International Nuclear Information System (INIS)

    Haupt, Larisa M; Thompson, Erik W; Trezise, Ann EO; Irving, Rachel E; Irving, Michael G; Griffiths, Lyn R

    2006-01-01

    Members of the matrix metalloproteinase (MMP) family of proteases are required for the degradation of the basement membrane and extracellular matrix in both normal and pathological conditions. In vitro, MT1-MMP (MMP-14, membrane type-1-MMP) expression is higher in more invasive human breast cancer (HBC) cell lines, whilst in vivo its expression has been associated with the stroma surrounding breast tumours. MMP-1 (interstitial collagenase) has been associated with MDA-MB-231 invasion in vitro, while MMP-3 (stromelysin-1) has been localised around invasive cells of breast tumours in vivo. As MMPs are not stored intracellularly, the ability to localise their expression to their cells of origin is difficult. We utilised the unique in situ-reverse transcription-polymerase chain reaction (IS-RT-PCR) methodology to localise the in vitro and in vivo gene expression of MT1-MMP, MMP-1 and MMP-3 in human breast cancer. In vitro, MMP induction was examined in the MDA-MB-231 and MCF-7 HBC cell lines following exposure to Concanavalin A (Con A). In vivo, we examined their expression in archival paraffin embedded xenografts derived from a range of HBC cell lines of varied invasive and metastatic potential. Mouse xenografts are heterogenous, containing neoplastic human parenchyma with mouse stroma and vasculature and provide a reproducible in vivo model system correlated to the human disease state. In vitro, exposure to Con A increased MT1-MMP gene expression in MDA-MB-231 cells and decreased MT1-MMP gene expression in MCF-7 cells. MMP-1 and MMP-3 gene expression remained unchanged in both cell lines. In vivo, stromal cells recruited into each xenograft demonstrated differences in localised levels of MMP gene expression. Specifically, MDA-MB-231, MDA-MB-435 and Hs578T HBC cell lines are able to influence MMP gene expression in the surrounding stroma. We have demonstrated the applicability and sensitivity of IS-RT-PCR for the examination of MMP gene expression both in vitro and in

  10. Toxicities of Selected Essential Oils, Silicone Oils, and Paraffin Oil against the Common Bed Bug (Hemiptera: Cimicidae).

    Science.gov (United States)

    Zha, Chen; Wang, Changlu; Li, Andrew

    2018-02-09

    The common bed bug [Cimex lectularius L. (Hemiptera: Cimicidae)] and tropical bed bug [Cimex hemipterus F. (Hemiptera: Cimicidae)] resurged in the United States and many other countries over the past decades. The need for safe and effective bed bug control products propelled the development of numerous 'green insecticides', mostly with essential oils listed as active ingredients. Various inorganic and organic oils also were used for bed bug management. However, there are no published studies on their toxicities against bed bugs. In this study, we screened 18 essential oils, three silicone oils, and paraffin oil (C5-20 paraffins) for their toxicities against bed bugs. All the oils exhibited insecticidal activity in topical assays. Their toxicities varied significantly; all of the evaluated essential oils were less effective than silicone oils and paraffin oil. The LD50 values of the most effective essential oil (blood orange), paraffin oil, and the most effective silicone oil (dodecamethylpentasiloxane) are 0.184 ± 0.018, 0.069 ± 0.012, and 0.036 ± 0.005 mg per bug, respectively. Direct spray of 1% water solution of 3-[hydroxy (polyethyleneoxy) propyl] heptamethyltrisiloxane, the only silicone oil that mixes well with water, resulted in 92% bed bug mortality after 1 d. Results of this study indicate silicone oils and paraffin oil have the potential to be used as safer alternative bed bug control materials. © The Author(s) 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  11. Forest Fragments Surrounded by Sugar Cane Are More Inhospitable to Terrestrial Amphibian Abundance Than Fragments Surrounded by Pasture

    Directory of Open Access Journals (Sweden)

    Paula Eveline Ribeiro D’Anunciação

    2013-01-01

    Full Text Available In recent years, there has been increasing interest in matrix-type influence on forest fragments. Terrestrial amphibians are good bioindicators for this kind of research because of low vagility and high philopatry. This study compared richness, abundance, and species composition of terrestrial amphibians through pitfall traps in two sets of semideciduous seasonal forest fragments in southeastern Brazil, according to the predominant surrounding matrix (sugar cane and pasture. There were no differences in richness, but fragments surrounded by sugar cane had the lowest abundance of amphibians, whereas fragments surrounded by pastures had greater abundance. The most abundant species, Rhinella ornata, showed no biometric differences between fragment groups but like many other amphibians sampled showed very low numbers of individuals in fragments dominated by sugar cane fields. Our data indicate that the sugar cane matrix negatively influences the community of amphibians present in fragments surrounded by this type of land use.

  12. Triphenylmethane, a possible moderator material

    International Nuclear Information System (INIS)

    Hügle, Th.; Mocko, M.; Hartl, M.A.; Daemen, L.L.; Muhrer, G.

    2014-01-01

    New challenges in neutron scattering result in an increased demand in novel moderator concepts. The most direct way to address the problem would be to change the moderator material itself. However the range of available neutron moderator materials is small. In this paper, we discuss triphenylmethane, a possible moderator material especially promising for cold neutron moderator applications. Our investigations include a parallel experimental and theoretical approach ranging from cross-section measurements and inelastic neutron spectroscopy to molecular modeling. -- Highlights: • Triphenylmethane as a potential moderator material is discussed. • Parallel theoretical and experimental approach. • Possibly very useful for cold neutrons

  13. Moderation of neutron energy

    International Nuclear Information System (INIS)

    Marlatt, G.R.

    1986-01-01

    This patent describes a nuclear reactor system having a nuclear reactor which has a core including fuel assemblies, means for transmitting through the core a coolant, the coolant having a predetermined neutron-energy moderating property, sealed tubes in the core, each tube containing a material having a different neutron-energy moderating property than the coolant, means, when actuated, to engage at least certain of the tubes, for opening certain of the tubes to permit the coolant to replace the material in the tubes thereby to change the energy spectrum of the neutrons in the reactor, hydraulic means, connected to the opening means, for actuating the opening means to engage certain of the tubes to open the tubes. A device, external to the reactor, connected to the hydraulic means controlls the actuation of the opening means, the opening means being so set with reference to the tubes that only certain of the tubes are opened at any time as the opening means is advanced towards the tubes by the hydraulic means

  14. How do people define moderation?

    Science.gov (United States)

    vanDellen, Michelle R; Isherwood, Jennifer C; Delose, Julie E

    2016-06-01

    Eating in moderation is considered to be sound and practical advice for weight maintenance or prevention of weight gain. However, the concept of moderation is ambiguous, and the effect of moderation messages on consumption has yet to be empirically examined. The present manuscript examines how people define moderate consumption. We expected that people would define moderate consumption in ways that justified their current or desired consumption rather than view moderation as an objective standard. In Studies 1 and 2, moderate consumption was perceived to involve greater quantities of an unhealthy food (chocolate chip cookies, gummy candies) than perceptions of how much one should consume. In Study 3, participants generally perceived themselves to eat in moderation and defined moderate consumption as greater than their personal consumption. Furthermore, definitions of moderate consumption were related to personal consumption behaviors. Results suggest that the endorsement of moderation messages allows for a wide range of interpretations of moderate consumption. Thus, we conclude that moderation messages are unlikely to be effective messages for helping people maintain or lose weight. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. Alginate dressing and polyurethane film versus paraffin gauze in the treatment of split-thickness skin graft donor sites: a randomized controlled pilot study.

    Science.gov (United States)

    Kaiser, Dominik; Hafner, Jürg; Mayer, Dieter; French, Lars E; Läuchli, Severin

    2013-02-01

    To compare postoperative healing of split-thickness skin graft (STSG) donor sites using traditional dressings (paraffin gauze) or modern wound dressings (alginate dressing and polyurethane film) in a randomized controlled trial. Thirty patients were randomly assigned to treatment of an STSG donor site with an alginate dressing and a polyurethane film or nonadherent paraffin gauze. Outcome variables were pain (measured with a visual analog scale), amount of dressing changes, healing time, cosmetic outcome, treatment costs, and overall satisfaction with the procedure. There was no significant difference in pain (postoperative day 1: 2.1 vs 1.2, P = .26; postoperative days 5-7: 1.0 vs 0.9, P = .47; final removal: 1.9 vs 1.0, P = .19) and time to healing (18.1 vs 15.4 days, P = .29) between alginate/polyurethane film dressing and nonadherent paraffin gauze. The semiocclusive dressings with polyurethane film required multiple dressing changes, whereas the nonadherent paraffin gauze could be left in place until complete epithelialization. Treatment costs were substantially lower for paraffin gauze. Semiocclusive dressings with alginate dressings and polyurethane film showed no advantages over treatment with paraffin gauze. With lower costs and better patient acceptance, paraffin gauze dressings were the preferred treatment for STSG donor sites.

  16. Moderator Configuration Options for ESS

    DEFF Research Database (Denmark)

    Zanini, L.; Batkov, K.; Klinkby, Esben Bryndt

    2016-01-01

    The current, still evolving status of the design and the optimization work for the moderator configuration for the European Spallation Source is described. The moderator design has been strongly driven by the low-dimensional moderator concept recently proposed for use in spallation neutron sources...... or reactors. Quasi-two dimensional, disc- or tube-shaped moderators,can provide strong brightness increase (factor of 3 or more) with respect to volume para-H2moderators, which constitute the reference, state-of-the-art technology for high-intensity coupled moderators. In the design process other, more...... conventional, principles were also considered,such as the importance of moderator positioning, of the premoderator, and beam extraction considerations. Different design and configuration options are evaluated and compared with the reference volume moderator configuration described in the ESS Technical Design...

  17. Spallation neutron source moderator design

    International Nuclear Information System (INIS)

    Charlton, L.A.; Barnes, J.M.; Gabriel, T.A.; Johnson, J.O.

    1998-01-01

    This paper describes various aspects of the spallation neutron source (SNS) moderator design. Included are the effects of varying the moderator location, interaction effects between moderators, and the impact on neutron output when various reflector materials are used. Also included is a study of the neutron output from composite moderators, where it is found that a combination of liquid H 2 O and liquid H 2 can produce a spectrum very similar to liquid methane (L-CH 4 ). (orig.)

  18. SNS moderator design

    International Nuclear Information System (INIS)

    Charlton, L.A.; Barnes, J.M.; Gabriel, T.A.; Johnson, J.O.

    1997-01-01

    The pulsed-neutron source SNS facility will start operation at 1 MW. A later upgrade to 5 MW is planned. The facility consists of a linear accelerator, an accumulator ring, and a target station. The protons from the accumulator ring will be injected into the target station at 1 GeV. The subsequent spallation process will then produce low-energy thermal neutrons that may be used for a wide variety of experiments. In this paper the authors discuss neutronic calculations which address various aspects of the moderate design. The computer codes HETC and MCNP were used for these calculations with the former code performing the high-energy transport. Neutrons which fell in energy to 20 MeV or less were then passed to MCNP for further transport

  19. FLUID MODERATED REACTOR

    Science.gov (United States)

    Wigner, E.P.; Ohlinger, L.A.; Young, G.J.; Weinberg, A.M.

    1957-10-22

    A reactor which utilizes fissionable fuel elements in rod form immersed in a moderator or heavy water and a means of circulating the heavy water so that it may also function as a coolant to remove the heat generated by the fission of the fuel are described. In this design, the clad fuel elements are held in vertical tubes immersed in heavy water in a tank. The water is circulated in a closed system by entering near the tops of the tubes, passing downward through the tubes over the fuel elements and out into the tank, where it is drawn off at the bottom, passed through heat exchangers to give up its heat and then returned to the tops of the tubes for recirculation.

  20. Placental vascular responses are dependent on surrounding tissue

    DEFF Research Database (Denmark)

    Brøgger, Torbjørn Halle

    -depth understanding of the mechanism regulating blood flow and perfusion is necessary if we are to come up with new ideas for intervention and treatment. Method: From fresh born placentas stem villi arteries were carefully dissected. The artery branches were divided. The surrounding tissue was removed from one end...... and was left untouched in the other end. Then using wire myography they were investigated in terms of contractility and sensitivity to physiological relevant human-like agonists. Results: Sensitivity to PGF2α, Tx-analog, 5-HT and endothelin-1 was significantly lower in arteries with intact surrounding tissue...... compared to arteries stripped of the tissue. The maximal force development was also significantly lower in arteries with surrounding tissue, when they were depolarized high extracellular [K+] or stimulated with PGF2α or endotheline-1. Conclusion: The perivascular tissue significantly alters stem villi...

  1. Placental vascular responses are dependent on surrounding tissue

    DEFF Research Database (Denmark)

    Brøgger, Torbjørn Halle

    . Materials and methods. From fresh born placentas, stem villi arteries were carefully dissected. The artery branches were divided. The surrounding tissue was removed from one end and was left untouched in the other end.Then, using wire myography, they were investigated in terms of contractility...... and sensitivity to physiological relevant human-like agonists. Results. Sensitivity to PGF2α, Tx-analog, 5-HT and endothelin-1 was significantly lower in arteries with intact surrounding tissue compared to arteries stripped of the tissue. The maximal force development was also significantly lower in arteries...... with surrounding tissue when they were depolarized high extracellular [K+] or stimulated with PGF2α or endotheline-1. Conclusion. The perivascular tissue significantly alters stem villi arteries' sensitivity and force development in a suppressive way. This implicates a new aspect of blood flow regulation...

  2. Surrounding rock stress analysis of underground high level waste repository

    International Nuclear Information System (INIS)

    Liu Wengang; Wang Ju; Wang Guangdi

    2006-01-01

    During decay of nuclear waste, enormous energy was released, which results in temperature change of surrounding rock of depository. Thermal stress was produced because thermal expansion of rock was controlled. Internal structure of surrounding rock was damaged and strength of rock was weakened. So, variation of stress was a dynamic process with the variation of temperature. BeiShan region of Gansu province was determined to be the depository field in the future, it is essential to make research on granite in this region. In the process of experiment, basic physical parameters of granite were analyzed preliminary with MTS. Long range temperature and stress filed was simulated considering the damage effect of surrounding rock, and rules of temperature and stress was achieved. (authors)

  3. The effect of a paraffin screen on the neutron dose at the maze door of a 15 MV linear accelerator.

    Science.gov (United States)

    Krmar, M; Nikolić, D; Kuzmanović, A; Kuzmanović, Z; Ganezer, K

    2013-08-01

    The purpose of this study was to explore the effects of a paraffin screen located at various positions in the maze on the neutron dose equivalent at the maze door. The neutron dose equivalent was measured at the maze door of a room containing a 15 MV linear accelerator for x-ray therapy. Measurements were performed for several positions of the paraffin screen covering only 27.5% of the cross-sectional area of the maze. The neutron dose equivalent was also measured at all screen positions. Two simple models of the neutron source were considered in which the first assumed that the source was the cross-sectional area at the inner entrance of the maze, radiating neutrons in an isotropic manner. In the second model the reduction in the neutron dose equivalent at the maze door due to the paraffin screen was considered to be a function of the mean values of the neutron fluence and energy at the screen. The results of this study indicate that the equivalent dose at the maze door was reduced by a factor of 3 through the use of a paraffin screen that was placed inside the maze. It was also determined that the contributions to the dosage from areas that were not covered by the paraffin screen as viewed from the dosimeter, were 2.5 times higher than the contributions from the covered areas. This study also concluded that the contributions of the maze walls, ceiling, and floor to the total neutron dose equivalent were an order of magnitude lower than those from the surface at the far end of the maze. This study demonstrated that a paraffin screen could be used to reduce the neutron dose equivalent at the maze door by a factor of 3. This paper also found that the reduction of the neutron dose equivalent was a linear function of the area covered by the maze screen and that the decrease in the dose at the maze door could be modeled as an exponential function of the product φ·E at the screen.

  4. Ethene/ethane and propene/propane separation via the olefin and paraffin selective metal-organic framework adsorbents CPO-27 and ZIF-8.

    Science.gov (United States)

    Böhme, Ulrike; Barth, Benjamin; Paula, Carolin; Kuhnt, Andreas; Schwieger, Wilhelm; Mundstock, Alexander; Caro, Jürgen; Hartmann, Martin

    2013-07-09

    Two types of metal-organic frameworks (MOFs) have been synthesized and evaluated in the separation of C2 and C3 olefins and paraffins. Whereas Co2(dhtp) (=Co-CPO-27 = Co-MOF-74) and Mg2(dhtp) show an adsorption selectivity for the olefins ethene and propene over the paraffins ethane and propane, the zeolitic imidazolate framework ZIF-8 behaves in the opposite way and preferentially adsorbs the alkane. Consequently, in breakthrough experiments, the olefins or paraffins, respectively, can be separated.

  5. Evaluation of thermal stability of paraffin wax by differential scanning calorimetry; Avaliacao da estabilidade termica de parafina por calorimetria diferencial de varredura

    Energy Technology Data Exchange (ETDEWEB)

    Godinho, K.O.; Silva, A.G.P.; Holanda, J.N.F. [Universidade Estadual do Norte Fluminense (LAMAV/UENF), Campos dos Goytacazes, RJ (Brazil). Grupo de Materiais Ceramicos], Email: holanda@uenf.br

    2010-07-01

    Phase change materials for heat storage are used as passive solar energy storage materials, which can be impregnated into construction materials. In this work the thermal stability (heating/cooling cycle) of the paraffin wax was investigated using differential scanning calorimetry. The latent heat and fusion temperature were determined for the following thermal cycles: 0, 30, 180 and 360. The thermal stability for paraffin wax infiltrated in support of gypsum was also determined. The experimental results showed that the paraffin wax showed good thermal stability in the states pure and infiltrated for up to 360 thermal cycles. (author)

  6. Transient Moderator Simulation Using CFX10-CAMO, a CANDU Moderator Analysis Model Based on a Coupled Solver

    International Nuclear Information System (INIS)

    Yoon, Churl; Park, Joo Hwan

    2007-01-01

    When a PHT(Primary Heat Transfer) system fails to remove excess heat from fuel channels for some loss of coolant accidents(LOCA's) in CANDU NPP's, the fuel channel temperature could increase until the pressure tube strains (i.e., balloon or sag) to contact its surrounding Calandria tube.(PT/CT contact) Following a PT/CT contact, there is a spike in the heat flux to the moderator surrounding the Calandria tube, which may lead to a sustained CT dryout and also a failure of a fuel channel. The prevention of a CT dryout following a PT/CT contact depends on the local moderator subcooling. That is, fuel channel integrity depends on the capability of the moderator to act as the ultimate heat sink for some LOCA's in a CANDU reactor. In KAERI, Yoon et al. developed a CFD model for predicting a CANDU-6 moderator temperature on the basis of a commercial CFD code CFX-4(ANSYS Inc.). This analytic model has the strength of modelling the hydraulic resistances in the core region and accounting for a heat source term in the energy equations. But convergence difficulties and a slow computing speed are the limitations of this model, because the CFX-4 code adapts a segregated solver to resolve a moderator circulation including a strong coupled-effect. Compared to a segregated solver, a coupled-solver is highly efficient and robust especially for a flow with a strong interference between the variables such as combustion

  7. Images of paraffin monolayer crystals with perfect contrast: Minimization of beam-induced specimen motion

    International Nuclear Information System (INIS)

    Glaeser, R.M.; McMullan, G.; Faruqi, A.R.; Henderson, R.

    2011-01-01

    Quantitative analysis of electron microscope images of organic and biological two-dimensional crystals has previously shown that the absolute contrast reached only a fraction of that expected theoretically from the electron diffraction amplitudes. The accepted explanation for this is that irradiation of the specimen causes beam-induced charging or movement, which in turn causes blurring of the image due to image or specimen movement. In this paper, we used three different approaches to try to overcome this image-blurring problem in monolayer crystals of paraffin. Our first approach was to use an extreme form of spotscan imaging, in which a single image was assembled on film by the successive illumination of up to 50,000 spots, each of a diameter of around 7 nm. The second approach was to use the Medipix II detector with its zero-noise readout to assemble a time-sliced series of images of the same area in which each frame from a movie with up to 400 frames had an exposure of only 500 electrons. In the third approach, we simply used a much thicker carbon support film to increase the physical strength and conductivity of the support. Surprisingly, the first two methods involving dose fractionation in space or time produced only partial improvements in contrast whereas the third approach produced many virtually perfect images, where the absolute contrast predicted from the electron diffraction amplitudes was observed in the images. We conclude that it is possible to obtain consistently almost perfect images of beam-sensitive specimens if they are attached to an appropriately strong and conductive support; however great care is needed in practice and the problem remains of how to best image ice-embedded biological structures in the absence of a strong, conductive support film. -- Research Highlights: →Three ideas were tested to improve the contrast of images of an organic specimen. →High-resolution images of paraffin on thick carbon films can have perfect contrast

  8. Images of paraffin monolayer crystals with perfect contrast: Minimization of beam-induced specimen motion

    Energy Technology Data Exchange (ETDEWEB)

    Glaeser, R.M. [Lawrence Berkeley National Laboratory, University of California, Berkeley, CA 94720 (United States); McMullan, G.; Faruqi, A.R. [MRC Laboratory of Molecular Biology, Hills Road, Cambridge CB2 0QH (United Kingdom); Henderson, R., E-mail: rh15@mrc-lmb.cam.ac.uk [MRC Laboratory of Molecular Biology, Hills Road, Cambridge CB2 0QH (United Kingdom)

    2011-01-15

    Quantitative analysis of electron microscope images of organic and biological two-dimensional crystals has previously shown that the absolute contrast reached only a fraction of that expected theoretically from the electron diffraction amplitudes. The accepted explanation for this is that irradiation of the specimen causes beam-induced charging or movement, which in turn causes blurring of the image due to image or specimen movement. In this paper, we used three different approaches to try to overcome this image-blurring problem in monolayer crystals of paraffin. Our first approach was to use an extreme form of spotscan imaging, in which a single image was assembled on film by the successive illumination of up to 50,000 spots, each of a diameter of around 7 nm. The second approach was to use the Medipix II detector with its zero-noise readout to assemble a time-sliced series of images of the same area in which each frame from a movie with up to 400 frames had an exposure of only 500 electrons. In the third approach, we simply used a much thicker carbon support film to increase the physical strength and conductivity of the support. Surprisingly, the first two methods involving dose fractionation in space or time produced only partial improvements in contrast whereas the third approach produced many virtually perfect images, where the absolute contrast predicted from the electron diffraction amplitudes was observed in the images. We conclude that it is possible to obtain consistently almost perfect images of beam-sensitive specimens if they are attached to an appropriately strong and conductive support; however great care is needed in practice and the problem remains of how to best image ice-embedded biological structures in the absence of a strong, conductive support film. -- Research Highlights: {yields}Three ideas were tested to improve the contrast of images of an organic specimen. {yields}High-resolution images of paraffin on thick carbon films can have perfect

  9. Biomedical analysis of formalin-fixed, paraffin-embedded tissue samples: The Holy Grail for molecular diagnostics.

    Science.gov (United States)

    Donczo, Boglarka; Guttman, Andras

    2018-06-05

    More than a century ago in 1893, a revolutionary idea about fixing biological tissue specimens was introduced by Ferdinand Blum, a German physician. Since then, a plethora of fixation methods have been investigated and used. Formalin fixation with paraffin embedment became the most widely used types of fixation and preservation method, due to its proper architectural conservation of tissue structures and cellular shape. The huge collection of formalin-fixed, paraffin-embedded (FFPE) sample archives worldwide holds a large amount of unearthed information about diseases that could be the Holy Grail in contemporary biomarker research utilizing analytical omics based molecular diagnostics. The aim of this review is to critically evaluate the omics options for FFPE tissue sample analysis in the molecular diagnostics field. Copyright © 2018. Published by Elsevier B.V.

  10. Simultaneous phenotyping and genotyping (FICTION-methodology) on paraffin sections and cytologic specimens: a comparison of 2 different protocols

    DEFF Research Database (Denmark)

    Bzorek, M.Sr.; Hansen, L.; Petersen, Bodil Laub

    2008-01-01

    for the investigation of neoplasms)]. However, few studies have been applied to the technical problems posed by antigen retrieval and accessibility of genetic probes to target-DNA, using formalin-fixed, paraffin-embedded tissue. In this study, we compared 2 immunofluorescence detection systems, the 3-step IF (TIF......) method against the Tyramide Signal Amplification techniques (TSA). The FICTION-TSA technique significantly improved the sensitivity for detection of the immunophenotypic markers without influencing specific probe hybridization to target-DNA, compared with the results obtained with the TIF method....... The reaction product of the TSA system was robust to the following FISH procedure in contrast to the TIF technique. The TSA technique used also allowed synchronous detection of nuclear antigens and FISH signals using both fusion (IgH/CCND1) and break-apart (CCND1) probes on formalin-fixed paraffin...

  11. A comparative study on the protection effect in the radiation-induced oxidation of liquid paraffins and polypropylene

    International Nuclear Information System (INIS)

    Soebianto, Y.S.; Kusuhata, Isami; Katsumura, Yosuke; Ishigure, Kenkichi; Kubo, Junichi; Hamakawa, Satoru; Azami, Kiyoshi; Kudoh, Hisaaki; Seguchi, Tadao.

    1995-01-01

    Comparison of protection effect of additives in liquid paraffins and polypropylene (PP) irradiation under pure oxygen atmosphere has been carried out. Gas product analysis and mechanical properties measurement of PP films indicate that the presence of additives reduces O 2 uptake, gas evolution and molecular degradation. These facts are attributed to energy and charge transfer, and radical scavenging action of the additive molecules regardless the physical state difference of the substrates. Oxidation pathway in liquid paraffin is shorter than that in solid PP, and the main part of the consumed O 2 are converted into carboxylic acids. The excess of H 2 evolution observed in PP oxidation is produced during the oxidation step, and transformation of the additives in their function as protector. (author)

  12. Analytical validation of a melanoma diagnostic gene signature using formalin-fixed paraffin-embedded melanocytic lesions.

    Science.gov (United States)

    Warf, M Bryan; Flake, Darl D; Adams, Doug; Gutin, Alexander; Kolquist, Kathryn A; Wenstrup, Richard J; Roa, Benjamin B

    2015-01-01

    These studies were to validate the analytical performance of a gene expression signature that differentiates melanoma and nevi, using RNA expression from 14 signature genes and nine normalization genes that generates a melanoma diagnostic score (MDS). Formalin-fixed paraffin-embedded melanocytic lesions were evaluated in these studies. The overall SD of the assay was determined to be 0.69 MDS units. Individual amplicons within the signature had an average amplification efficiency of 92% and a SD less than 0.5 CT. The MDS was reproducible across a 2000-fold dilution range of input RNA. Melanin, an inhibitor of PCR, does not interfere with the signature. These studies indicate this signature is robust and reproducible and is analytically validated on formalin-fixed paraffin-embedded melanocytic lesions.

  13. Study of the petroleum schedules thermal cleaning process from asphalt, ressin and paraffin deposits using low- temperature plasma

    International Nuclear Information System (INIS)

    Samigullin, A D; Galiakbarov, A T; Galiakbarov, R T

    2016-01-01

    Petroleum industry uses large amount of pumping and compression pipes. Carrying out the whole range of repair works requires cleaning of the pipe inner surface from deposits which appeared in it during operation [1]. The task of asphalt, resin and paraffin deposits control remains one of the most essential for the branch. The article deals with thermal method and device for asphalt, resin and paraffin deposits removal from pumping and compression pipes inner surface, describes and provides the device application scope for cleaning the pumping and compression pipes inner surface. To deal with borehole equipment and pipe systems waxing problem various deposit prevention and removal methods are used, including mechanical, thermal, chemical, combined and nonconventional methods. (paper)

  14. Understanding Kelvin-Helmholtz instability in paraffin-based hybrid rocket fuels

    Science.gov (United States)

    Petrarolo, Anna; Kobald, Mario; Schlechtriem, Stefan

    2018-04-01

    Liquefying fuels show higher regression rates than the classical polymeric ones. They are able to form, along their burning surface, a low viscosity and surface tension liquid layer, which can become unstable (Kelvin-Helmholtz instability) due to the high velocity gas flow in the fuel port. This causes entrainment of liquid droplets from the fuel surface into the oxidizer gas flow. To better understand the droplets entrainment mechanism, optical investigations on the combustion behaviour of paraffin-based hybrid rocket fuels in combination with gaseous oxygen have been conducted in the framework of this research. Combustion tests were performed in a 2D single-slab burner at atmospheric conditions. High speed videos were recorded and analysed with two decomposition techniques. Proper orthogonal decomposition (POD) and independent component analysis (ICA) were applied to the scalar field of the flame luminosity. The most excited frequencies and wavelengths of the wave-like structures characterizing the liquid melt layer were computed. The fuel slab viscosity and the oxidizer mass flow were varied to study their influence on the liquid layer instability process. The combustion is dominated by periodic, wave-like structures for all the analysed fuels. Frequencies and wavelengths characterizing the liquid melt layer depend on the fuel viscosity and oxidizer mass flow. Moreover, for very low mass flows, no wavelength peaks are detected for the higher viscosity fuels. This is important to better understand and predict the onset and development of the entrainment process, which is connected to the amplification of the longitudinal waves.

  15. Effect of Zeolite Treatment on the Blooming Behavior of Paraffin Wax in Natural Rubber Composites

    Directory of Open Access Journals (Sweden)

    Bryan B. Pajarito

    2016-06-01

    Full Text Available The blooming behavior of paraffin wax in natural rubber (NR composites was studied as function of zeolite treatment. Three types of zeolite treatment were treated as factors: acid activation using hydrochloric acid (HCl solution, ion exchange using tetradecyldimethyl amine (TDA chloride salt, and organic modification using glycerol monostearate (GMS. The zeolite was treated according to a 23 full factorial design of experiment. Attenuated total reflectance – Fourier transform infrared (ATR-FTIR spectroscopy was used to characterize the chemical structure of treated zeolite. Treated zeolite was applied as filler to NR composites deliberately compounded with high amount of paraff in wax. The amount of bloomed wax in surface of NR composite sheets was monitored with time at 50oC. Results show the bloom amount to be linear with the square root of time. NR composites reinforced with untreated, acid-activated, and ion-exchanged zeolite fillers indicate reduction in wax blooming as compared to unfilled NR. The bloom rate (slope and initial bloom (y-intercept were determined from the experimental plots. Analysis of variance (ANOVA shows the bloom rate to be signif icantly increased when zeolite fillers are treated with GMS. Meanwhile, initial bloom was significantly enhanced when zeolite fillers are treated with TDA chloride salt and GMS. The significant increase in bloom rate and initial bloom can be attributed to the softening of the NR matrix at high amounts of TDA chloride salt and GMS.

  16. Obtaining low-congealing oils and paraffins by carbamide deparaffinization method

    Energy Technology Data Exchange (ETDEWEB)

    Kalambet, I A; Dorodnova, V S

    1982-07-01

    Ethane cooling is required to obtain oils with congealing points lower than 15-20/sup 0/C. Thus a process of carbamide deparaffinization that would be relatively simple and would not require special cooling equipment was deemed desirable. Filtrates were selected from an oil separating device after basic solid paraffins had been removed. They were subjected to hydropurification with an alumimum-cobalt-molybdenum catalyst at 4 MPa pressure, 320/sup 0/C, feed of 1.5c/sup -1/ and hydrogen-containing gas compressed to 500 m/sup 3//m/sup 3/. Results showed that the initial mixed hydrocarbon filtrate was deparaffinized under these conditions to produce an oil that congealed on the average at temperatures 2-3/sup 0/ lower than controls. A benzine fraction at 80-120/sup 0/C was used as the solvent and methanol served as the activator. Using distillates from Stavropol crude oil, it was possible to obtain oils.

  17. Core-Sheath Paraffin-Wax-Loaded Nanofibers by Electrospinning for Heat Storage.

    Science.gov (United States)

    Lu, Yuan; Xiao, Xiudi; Zhan, Yongjun; Huan, Changmeng; Qi, Shuai; Cheng, Haoliang; Xu, Gang

    2018-04-18

    Paraffin wax (PW) is widely used for smart thermoregulation materials due to its good thermal performance. However, the leakage and low thermal conductivity of PW hinder its application in the heat storage field. Accordingly, developing effective methods to address these issues is of great importance. In this study, we explored a facile approach to obtain PW-loaded core-sheath structured flexible nanofibers films via coaxial electrospinning technique. The PW as the core layer was successfully encapsulated by the sheath-layer poly(methyl methacrylate). The diameter of the fiber core increased from 395 to 848 nm as the core solution speed rate increased from 0.1 to 0.5 mL/h. In addition, it can be seen that higher core solution speed rate could lead to higher PW encapsulation efficiency according to the transmission electron microscopy results. The core-sheath nanofiber films, moreover, possessed the highest latent heat of 58.25 J/g and solidifying enthalpy of -56.49 J/g. In addition, we found that after 200 thermal cycles, there was little change in latent heat, which demonstrated that it is beneficial for the PW-loaded core-sheath structure to overcome the leakage issue and enhance thermal stability properties for the thermoregulation film.

  18. Altitude profiles of total chlorinated paraffins in humus and spruce needles from the Alps (MONARPOP)

    Energy Technology Data Exchange (ETDEWEB)

    Iozza, Saverio, E-mail: saverio.iozza@empa.c [Empa, Swiss Federal Laboratories for Materials Testing and Research, Laboratory for Analytical Chemistry, Uberlandstrasse 129, CH-8600 Duebendorf (Switzerland); University of Basel, Department of Chemistry, St. Johanns-Ring 19, CH-4056 Basel (Switzerland); Schmid, Peter, E-mail: peter.schmid@empa.c [Empa, Swiss Federal Laboratories for Materials Testing and Research, Laboratory for Analytical Chemistry, Uberlandstrasse 129, CH-8600 Duebendorf (Switzerland); Oehme, Michael, E-mail: michael.oehme@unibas.c [University of Basel, Department of Chemistry, St. Johanns-Ring 19, CH-4056 Basel (Switzerland); Bassan, Rodolfo [Regional Agency for Environmental Prevention and Protection of Veneto (Italy); Belis, Claudio [Regional Agency for Environmental Protection of Lombardia (Italy); Jakobi, Gert; Kirchner, Manfred; Schramm, Karl-Werner [GSF-National Research Centre for Environment and Health (Germany); Kraeuchi, Norbert [Swiss Federal Institute for Forest, Snow and Landscape Research (Switzerland); Moche, Wolfgang; Offenthaler, Ivo; Weiss, Peter [Federal Environment Agency Ltd. (Austria); Simoncic, Primoz [Slovenian Forestry Institute (Slovenia); Knoth, Wilhelm [Federal Environment Agency (Germany)

    2009-12-15

    Chlorinated paraffins (CPs) are toxic, bioaccumulative, persistent, and ubiquitously present in the environment. CPs were analyzed in humus and needle samples, which were taken within the Monitoring Network in the Alpine Region for Persistent and other Organic Pollutants (MONARPOP) at sampling sites of 7 different altitude profiles in the Alps. Gas chromatography combined with electron ionization tandem mass spectrometry (EI-MS/MS) was used for the determination of total CPs (sum of short, medium and long chain CPs). CPs were found in all samples; the concentrations varied between 7 and 199 ng g{sup -1} dry weight (dw) and within 26 and 460 ng g{sup -1} dw in humus and needle samples, respectively. A clear vertical tendency within the individual altitude profiles could not be ascertained. Within all altitude profiles, elevated concentrations were observed in humus samples taken between 700 and 900 m and between 1300 and 1500 m. In the needle samples no similar correlation could be observed due to higher variation of the data. - For the first time, CP levels of humus and spruce needle samples from the Alps (MONARPOP) were presented including the evaluation of altitude profiles.

  19. Building Energy Storage Panel Based on Paraffin/Expanded Perlite: Preparation and Thermal Performance Study.

    Science.gov (United States)

    Kong, Xiangfei; Zhong, Yuliang; Rong, Xian; Min, Chunhua; Qi, Chengying

    2016-01-25

    This study is focused on the preparation and performance of a building energy storage panel (BESP). The BESP was fabricated through a mold pressing method based on phase change material particle (PCMP), which was prepared in two steps: vacuum absorption and surface film coating. Firstly, phase change material (PCM) was incorporated into expanded perlite (EP) through a vacuum absorption method to obtain composite PCM; secondly, the composite PCM was immersed into the mixture of colloidal silica and organic acrylate, and then it was taken out and dried naturally. A series of experiments, including differential scanning calorimeter (DSC), scanning electron microscope (SEM), best matching test, and durability test, have been conducted to characterize and analyze the thermophysical property and reliability of PCMP. Additionally, the thermal performance of BESP was studied through a dynamic thermal property test. The results have showed that: (1) the surface film coating procedure can effectively solve the leakage problem of composite phase change material prepared by vacuum impregnation; (2) the optimum adsorption ratio for paraffin and EP was 52.5:47.5 in mass fraction, and the PCMP has good thermal properties, stability, and durability; and (3) in the process of dynamic thermal performance test, BESP have low temperature variation, significant temperature lagging, and large heat storage ability, which indicated the potential of BESP in the application of building energy efficiency.

  20. Endosulfan, pentachlorobenzene and short-chain chlorinated paraffins in background soils from Western Europe.

    Science.gov (United States)

    Halse, Anne Karine; Schlabach, Martin; Schuster, Jasmin K; Jones, Kevin C; Steinnes, Eiliv; Breivik, Knut

    2015-01-01

    Soils are major reservoirs for many persistent organic pollutants (POPs). In this study, "newly" regulated POPs i.e. Σendosulfans (α-endosulfan, β-endosulfan, endosulfan sulfate), pentachlorobenzene (PeCB), and short-chain chlorinated paraffins (SCCPs) were determined in background samples from woodland (WL) and grassland (GL) surface soil, collected along an existing latitudinal UK-Norway transect. Statistical analysis, complemented with plots showing the predicted equilibrium distribution and mobility potential, was then explored to discuss factors controlling their spatial distribution. SCCPs were detected with the highest average concentrations (35 ± 100 ng/g soil organic matter (SOM)), followed by Σendosulfans (3 ± 3 ng/g SOM) and PeCB (1 ± 1 ng/g SOM). PeCB and Σendosulfans share many similarities in their distribution in these background soils as well as with several legacy POPs. A steep decline in concentrations of SCCPs with increasing latitude indicates that their occurrence is dictated by proximity to source regions, while concentrations of Σendosulfans peaked in regions experiencing elevated precipitation rates. Copyright © 2014 Elsevier Ltd. All rights reserved.

  1. Molecular Markers for Prostate Cancer in Formalin-Fixed Paraffin-Embedded Tissues

    Directory of Open Access Journals (Sweden)

    Tamara Sequeiros

    2013-01-01

    Full Text Available Prostate cancer (PCa is the most frequently diagnosed type of cancer in developed countries. The decisive method of diagnosis is based on the results of biopsies, morphologically evaluated to determine the presence or absence of cancer. Although this approach leads to a confident diagnosis in most cases, it can be improved by using the molecular markers present in the tissue. Both miRNAs and proteins are considered excellent candidates for biomarkers in formalin-fixed paraffin-embedded (FFPE tissues, due to their stability over long periods of time. In the last few years, a concerted effort has been made to develop the necessary tools for their reliable measurement in these types of samples. Furthermore, the use of these kinds of markers may also help in establishing tumor grade and aggressiveness, as well as predicting the possible outcomes in each particular case for the different treatments available. This would aid clinicians in the decision-making process. In this review, we attempt to summarize and discuss the potential use of microRNA and protein profiles in FFPE tissue samples as markers to better predict PCa diagnosis, progression, and response to therapy.

  2. Short-Chain Chlorinated Paraffins in Zurich, Switzerland--Atmospheric Concentrations and Emissions.

    Science.gov (United States)

    Diefenbacher, Pascal S; Bogdal, Christian; Gerecke, Andreas C; Glüge, Juliane; Schmid, Peter; Scheringer, Martin; Hungerbühler, Konrad

    2015-08-18

    Short-chain chlorinated paraffins (SCCPs) are of concern due to their potential for adverse health effects, bioaccumulation, persistence, and long-range transport. Data on concentrations of SCCPs in urban areas and underlying emissions are still scarce. In this study, we investigated the levels and spatial distribution of SCCPs in air, based on two separate, spatially resolved sampling campaigns in the city of Zurich, Switzerland. SCCP concentrations in air ranged from 1.8 to 17 ng·m(-3) (spring 2011) and 1.1 to 42 ng·m(-3) (spring 2013) with medians of 4.3 and 2.7 ng·m(-3), respectively. Both data sets show that atmospheric SCCP levels in Zurich can vary substantially and may be influenced by a number of localized sources within this urban area. Additionally, continuous measurements of atmospheric concentrations performed at one representative sampling site in the city center from 2011 to 2013 showed strong seasonal variations with high SCCP concentrations in summer and lower levels in winter. A long-term dynamic multimedia environmental fate model was parametrized to simulate the seasonal trends of SCCP concentrations in air and to back-calculate urban emissions. Resulting annual SCCP emissions in the city of Zurich accounted for 218-321 kg, which indicates that large SCCP stocks are present in urban areas of industrialized countries.

  3. [Contamination characteristics of short-chain chlorinated paraffins in edible fish of Shanghai].

    Science.gov (United States)

    Jiang, Guo; Chen, Lai-guo; He, Qiu-sheng; Meng, Xiang-zhou; Feng, Yong-bin; Huang, Yu-mei; Tang, Cai-ming

    2013-09-01

    According to the local habit of eating fish, in a total of 68 samples, 8 kinds of different trophic levels of edible fish collected in Shanghai were determined in terms of concentration and distribution profile of short chain chlorinated paraffin (SCCPs) in muscles to investigate the pollution status of SCCPs in edible fish from the Yangtze River Delta region. The results indicated that the concentrations (dw) of SCCPs in edible fish were in the range of 36-801 ng x g(-1). With the increase in carbon chain length, the concentration of SCCPs decreased. In addition, lower chlorinated (Cl6-Cl8) and shorter chain (Cl10, C11) congeners were the dominant chlorine and carbon homologues groups, respectively, contributing a total relative abundance of 61.46%-82.50% to the total abundance of SCCPs. The levels of SCCPs in fish of Shanghai were in the medium level worldwide, and the distribution pattern was in line with those of the domestic and foreign studies.

  4. [Levels and distribution of short chain chlorinated paraffins in seafood from Dalian, China].

    Science.gov (United States)

    Yu, Jun-Chao; Wang, Thanh; Wang, Ya-Wei; Meng, Mei; Chen, Ru; Jiang, Gui-Bin

    2014-05-01

    Seafood samples were collected from Dalian, China to study the accumulation and distribution characteristics of short chain chlorinated paraffins (SCCPs) by GC/ECNI-LRMS. Sum of SCCPs (dry weight) were in the range of 77-8 250 ng.g-1, with the lowest value in Scapharca subcrenata and highest concentration in Neptunea cumingi. The concentrations of sum of SCCPs (dry weight) in fish, shrimp/crab and shellfish were in the ranges of 100-3 510, 394-5 440, and 77-8 250 ng.g-1 , respectively. Overall, the C10 and C11 homologues were the most predominant carbon groups of SCCPs in seafood from this area,and a relatively higher proportion of C12-13 was observed in seafood with higher concentrations of sum of SCCPs . With regard to chlorine content, Cl1,, CI8 and CI6 were the major groups. Significant correlations were found among concentrations of different SCCP homologues (except C1, vs. Cl10 ) , which indicated that they might share the same sources and/or have similar accumulation, migration and transformation processes.

  5. Gridded emission inventory of short-chain chlorinated paraffins and its validation in China.

    Science.gov (United States)

    Jiang, Wanyanhan; Huang, Tao; Mao, Xiaoxuan; Wang, Li; Zhao, Yuan; Jia, Chenhui; Wang, Yanan; Gao, Hong; Ma, Jianmin

    2017-01-01

    China produces approximately 20%-30% of the total global chlorinated paraffins (CPs). The establishment of a short-chain CP (SCCP) emission inventory is a significant step toward risk assessment and regulation of SCCPs in China and throughout the globe. This study developed a gridded SCCPs emission inventory with a 1/4° longitude by 1/4° latitude resolution from 2008 to 2012 for China, which was based on the total annual CPs emissions for the nation. The total national SCCPs emission during this 5-year period was 5651.5 tons. An additive in metal cutting fluids was a major emission source in China, contributing 2680.2 tons to the total atmospheric emissions of SCCPs from 2008 to 2012, followed by the production of CPs (2281.8 tons), plasticizers (514.3 tons), flame retardants (108.6 tons), and net import (66.6 tons). Most of these emission sources are located along the eastern seaboard of China and southern China. A coupled atmospheric transport model was employed to simulate environmental contamination by SCCPs using the gridded emission inventory of SCCPs from 2008 to 2012 as the model initial conditions. Simulated atmospheric and soil concentrations were compared with field monitoring data to validate the emission inventory. The results showed good consistency between modeled and field sampling data, supporting the reliability and credibility of the gridded SCCPs emission inventory that was developed in the present study. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Macro-Encapsulated PCM Cylinder Module Based on Paraffin and Float Stones

    Directory of Open Access Journals (Sweden)

    Kailiang Huang

    2016-05-01

    Full Text Available Organic phase change material (PCM with macro-encapsulation is attractive in energy storage applications as it has relatively low cost. This study focuses on using PET plastic pipes to encapsulate paraffin and using low-cost float stones to increase the thermal conductivity of PCM modules as they have a special structure of high porosity. Float stones were immersed in the liquid PCM and an ultrasonic welding method used to prevent leakage of the PET plastic pipes. Scanning electron microscopy (SEM was used to discover the appearance of the composite PCM. The thermal performance of the PCM cylinder module was analyzed through experimental tests of a constant-temperature water bath and numerical simulations. The result indicates that this PCM Ccylinder module is superior in thermal energy storage compared with the reference module even though fewer PCM was contained and the latent heat loss is considerable. The pipe diameter is an important parameter when using this kind of PCM cylinder module in water tanks.

  7. Altitude profiles of total chlorinated paraffins in humus and spruce needles from the Alps (MONARPOP).

    Science.gov (United States)

    Iozza, Saverio; Schmid, Peter; Oehme, Michael; Bassan, Rodolfo; Belis, Claudio; Jakobi, Gert; Kirchner, Manfred; Schramm, Karl-Werner; Kräuchi, Norbert; Moche, Wolfgang; Offenthaler, Ivo; Weiss, Peter; Simoncic, Primoz; Knoth, Wilhelm

    2009-12-01

    Chlorinated paraffins (CPs) are toxic, bioaccumulative, persistent, and ubiquitously present in the environment. CPs were analyzed in humus and needle samples, which were taken within the Monitoring Network in the Alpine Region for Persistent and other Organic Pollutants (MONARPOP) at sampling sites of 7 different altitude profiles in the Alps. Gas chromatography combined with electron ionization tandem mass spectrometry (EI-MS/MS) was used for the determination of total CPs (sum of short, medium and long chain CPs). CPs were found in all samples; the concentrations varied between 7 and 199 ng g(-1) dry weight (dw) and within 26 and 460 ng g(-1) dw in humus and needle samples, respectively. A clear vertical tendency within the individual altitude profiles could not be ascertained. Within all altitude profiles, elevated concentrations were observed in humus samples taken between 700 and 900 m and between 1300 and 1500 m. In the needle samples no similar correlation could be observed due to higher variation of the data.

  8. Building Energy Storage Panel Based on Paraffin/Expanded Perlite: Preparation and Thermal Performance Study

    Directory of Open Access Journals (Sweden)

    Xiangfei Kong

    2016-01-01

    Full Text Available This study is focused on the preparation and performance of a building energy storage panel (BESP. The BESP was fabricated through a mold pressing method based on phase change material particle (PCMP, which was prepared in two steps: vacuum absorption and surface film coating. Firstly, phase change material (PCM was incorporated into expanded perlite (EP through a vacuum absorption method to obtain composite PCM; secondly, the composite PCM was immersed into the mixture of colloidal silica and organic acrylate, and then it was taken out and dried naturally. A series of experiments, including differential scanning calorimeter (DSC, scanning electron microscope (SEM, best matching test, and durability test, have been conducted to characterize and analyze the thermophysical property and reliability of PCMP. Additionally, the thermal performance of BESP was studied through a dynamic thermal property test. The results have showed that: (1 the surface film coating procedure can effectively solve the leakage problem of composite phase change material prepared by vacuum impregnation; (2 the optimum adsorption ratio for paraffin and EP was 52.5:47.5 in mass fraction, and the PCMP has good thermal properties, stability, and durability; and (3 in the process of dynamic thermal performance test, BESP have low temperature variation, significant temperature lagging, and large heat storage ability, which indicated the potential of BESP in the application of building energy efficiency.

  9. Polymerase chain reaction detection of retinoblastoma gene deletions in paraffin-embedded mouse lung adenocarcinomas

    International Nuclear Information System (INIS)

    Churchill, M.E.; Gemmell, M.A.; Woloschak, G.E.

    1991-01-01

    A Polymerase chain reaction (PCR) technique was used to detect deletions in the mouse retinoblastoma (mRb) gene using microtomed sections from paraffin-embedded radiation-induced and spontaneous tumors as the DNA source. Six mRb gene exon fragments were amplified in a 40-cycle, 3-temperature PCR protocol. Absence of any of these fragments relative to control PCR products on a Southern blot indicated a deletion of that portion of the mRb gene. Tumors chosen for analysis were lung adenocarcinomas that were judged to be the cause of death. Spontaneous tumors as well as those from irradiated mice (569 cGy of 60 Co γ rays or 60 cGy of JANUS neutrons) were analyzed. Tumors in six neutron-irradiated mice also had no mRb deletions. However, one of six tumors from γ-irradiated mice and 6 of 18 spontaneous tumors from unirradiated mice showed a deletion in one or both mRb alleles. All deletions detected were in the 5' region of the mRb gene

  10. High pressure combustion of liquid fuels. [alcohol and n-paraffin fuels

    Science.gov (United States)

    Canada, G. S.

    1974-01-01

    Measurements were made of the burning rates and liquid surface temperatures for a number of alcohol and n-paraffin fuels under natural and forced convection conditions. Porous spheres ranging in size from 0.64-1.9 cm O.D. were emloyed to simulate the fuel droplets. The natural convection cold gas tests considered the combustion in air of methanol, ethanol, propanol-1, n-pentane, n-heptane, and n-decane droplets at pressures up to 78 atmospheres. The pressure levels of the natural convection tests were high enough so that near critical combustion was observed for methanol and ethanol vaporization rates and liquid surface temperature measurements were made of droplets burning in a simulated combustion chamber environment. Ambient oxygen molar concentrations included 13%, 9.5% and pure evaporation. Fuels used in the forced convection atmospheric tests included those listed above for the natural convection tests. The ambient gas temperature ranged from 600 to 1500 K and the Reynolds number varied from 30 to 300. The high pressure forced convection tests employed ethanol and n-heptane as fuels over a pressure range of one to 40 atmospheres. The ambient gas temperature was 1145 K for the two combustion cases and 1255 K for the evaporation case.

  11. Heat transfer enhancement in energy storage in spherical capsules filled with paraffin wax and metal beads

    International Nuclear Information System (INIS)

    Ettouney, Hisham; Alatiqi, Imad; Al-Sahali, Mohammad; Al-Hajirie, Khalida

    2006-01-01

    Energy storage is an attractive option to conserve limited energy resources, where more than 50% of the generated industrial energy is discarded in cooling water and stack gases. This study focuses on the evaluation of heat transfer enhancement in phase change energy storage units. The experiments are performed using spherical capsules filled with paraffin wax and metal beads. The experiments are conducted by inserting a single spherical capsule filled with wax and metal beads in a stream of hot/cold air. Experimental measurements include the temperature field within the spherical capsule and in the air stream. To determine the enhancement effects of the metal beads, the measured data is correlated against those for a spherical capsule filled with pure wax. Data analysis shows a reduction of 15% in the melting and solidification times upon increasing the number and diameter of the metal beads. This reduction is caused by a similar decrease in the thermal load of the sphere due to replacement of the wax by metal beads. The small size of the spherical capsule limits the enhancement effects; this is evident upon comparison of the heat transfer in a larger size, double pipe energy storage unit, where 2% of the wax volume is replaced with metal inserts, result in a three fold reduction in the melting/solidification time and a similar enhancement in the heat transfer rate

  12. Comparison of Different Double Immunostaining Protocols for Paraffin Embedded Liver Tissue

    Directory of Open Access Journals (Sweden)

    Alexander Schütz

    1999-01-01

    Full Text Available Most of the double immunostaining protocols that have been introduced so far have been developed for application on fresh frozen material or based on different species antibodies. In liver tissue, general problems of double immunostaining techniques are further complicated by tissue‐specific difficulties, such as necrosis or high intracellular protein content. To assess a reliable double immunostaining protocol for archived, paraffin embedded liver tissue, different protocols based on the use of same species primary antibodies were evaluated in terms of sensitivity, specificity and non‐specific background staining in pathological liver specimens. We compared peroxidase–anti‐peroxidase, alkaline phosphatase–anti‐alkaline phosphatase (PAP/APAP, labelled‐avidin–biotin (LAB/LAB and digoxigenin–anti‐digoxigenin (dig–a‐dig/PAP techniques using different cytokeratin antibodies and an antibody against PCNA. Comparison of the double immunostaining techniques revealed a high sensitivity and specificity in all procedures. Sections, which were stained employing PAP/APAP‐technique, displayed a higher background staining compared to sections which were treated with the LAB/LAB or dig–a‐dig/PAP protocol. In contrast to the dig–a‐dig/PAP protocol, the LAB/LAB technique provides a better time/cost relationship. Therefore, we would like to recommend a modified LAB/LAB protocol for simultaneous detection of different antigens in archived liver tissue.

  13. In situ hybridization for the detection of rust fungi in paraffin embedded plant tissue sections.

    Science.gov (United States)

    Ellison, Mitchell A; McMahon, Michael B; Bonde, Morris R; Palmer, Cristi L; Luster, Douglas G

    2016-01-01

    Rust fungi are obligate pathogens with multiple life stages often including different spore types and multiple plant hosts. While individual rust pathogens are often associated with specific plants, a wide range of plant species are infected with rust fungi. To study the interactions between these important pathogenic fungi and their host plants, one must be able to differentiate fungal tissue from plant tissue. This can be accomplished using the In situ hybridization (ISH) protocol described here. To validate reproducibility using the ISH protocol, samples of Chrysanthemum × morifolium infected with Puccinia horiana, Gladiolus × hortulanus infected with Uromyces transversalis and Glycine max infected with Phakopsora pachyrhizi were tested alongside uninfected leaf tissue samples. The results of these tests show that this technique clearly distinguishes between rust pathogens and their respective host plant tissues. This ISH protocol is applicable to rust fungi and potentially other plant pathogenic fungi as well. It has been shown here that this protocol can be applied to pathogens from different genera of rust fungi with no background staining of plant tissue. We encourage the use of this protocol for the study of plant pathogenic fungi in paraffin embedded sections of host plant tissue.

  14. Fluorescent Molecular Rotor-in-Paraffin Waxes for Thermometry and Biometric Identification.

    Science.gov (United States)

    Jin, Young-Jae; Dogra, Rubal; Cheong, In Woo; Kwak, Giseop

    2015-07-08

    Novel thermoresponsive sensor systems consisting of a molecular rotor (MR) and paraffin wax (PW) were developed for various thermometric and biometric identification applications. Polydiphenylacetylenes (PDPAs) coupled with long alkyl chains were used as MRs, and PWs of hydrocarbons having 16-20 carbons were utilized as phase-change materials. The PDPAs were successfully dissolved in the molten PWs and did not act as an impurity that prevents phase transition of the PWs. These PDPA-in-PW hybrids had almost the same enthalpies and phase-transition temperatures as the corresponding pure PWs. The hybrids exhibited highly reversible fluorescence (FL) changes at the critical temperatures during phase transition of the PWs. These hybrids were impregnated into common filter paper in the molten state by absorption or were encapsulated into urea resin to enhance their mechanical integrity and cyclic stability during repeated use. The wax papers could be utilized in highly advanced applications including FL image writing/erasing, an array-type thermo-indicator, and fingerprint/palmprint identification. The present findings should facilitate the development of novel fluorescent sensor systems for biometric identification and are potentially applicable for biological and biomedical thermometry.

  15. Multi-elemental imaging of paraffin-embedded human samples by laser-induced breakdown spectroscopy

    Science.gov (United States)

    Moncayo, S.; Trichard, F.; Busser, B.; Sabatier-Vincent, M.; Pelascini, F.; Pinel, N.; Templier, I.; Charles, J.; Sancey, L.; Motto-Ros, V.

    2017-07-01

    Chemical elements play central roles for physiological homeostasis in human cells, and their dysregulation might lead to a certain number of pathologies. Novel imaging techniques that improve the work of pathologists for tissue analysis and diagnostics are continuously sought. We report the use of Laser-Induced Breakdown Spectroscopy (LIBS) to perform multi-elemental images of human paraffin-embedded skin samples on the entire biopsy scale in a complementary and compatible way with microscope histopathological examination. A specific instrumental configuration is proposed in order to detect most of the elements of medical interest (i.e. P, Al, Mg, Na, Zn, Si, Fe, and Cu). As an example of medical application, we selected and analysed skin biopsies, including healthy skin tissue, cutaneous metastasis of melanoma, Merkel-cell carcinoma and squamous cell carcinoma. Clear distinctions in the distribution of chemical elements are observed from the different samples investigated. This study demonstrates the high complementarity of LIBS elemental imaging with conventional histopathology, opening new opportunities for any medical application involving metals.

  16. Virus characterization and discovery in formalin-fixed paraffin-embedded tissues.

    Science.gov (United States)

    Bodewes, Rogier; van Run, Peter R W A; Schürch, Anita C; Koopmans, Marion P G; Osterhaus, Albert D M E; Baumgärtner, Wolfgang; Kuiken, Thijs; Smits, Saskia L

    2015-03-01

    Detection and characterization of novel viruses is hampered frequently by the lack of properly stored materials. Especially for the retrospective identification of viruses responsible for past disease outbreaks, often only formalin-fixed paraffin-embedded (FFPE) tissue samples are available. Although FFPE tissues can be used to detect known viral sequences, the application of FFPE tissues for detection of novel viruses is currently unclear. In the present study it was shown that sequence-independent amplification in combination with next-generation sequencing can be used to detect sequences of known and unknown viruses, although with relatively low sensitivity. These findings indicate that this technique could be useful for detecting novel viral sequences in FFPE tissues collected from humans and animals with disease of unknown origin, when other samples are not available. In addition, application of this method to FFPE tissues allows to correlate with the presence of histopathological changes in the corresponding tissue sections. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. Improved protein extraction and protein identification from archival formalin-fixed paraffin-embedded human aortas.

    Science.gov (United States)

    Fu, Zongming; Yan, Kun; Rosenberg, Avraham; Jin, Zhicheng; Crain, Barbara; Athas, Grace; Heide, Richard S Vander; Howard, Timothy; Everett, Allen D; Herrington, David; Van Eyk, Jennifer E

    2013-04-01

    Evaluate combination of heat and elevated pressure to enhance protein extraction and quality of formalin-fixed (FF), and FF paraffin-embedded (FFPE) aorta for proteomics. Proteins were extracted from fresh frozen aorta at room temperature (RT). FF and FFPE aortas (3 months and 15 years) were extracted at RT, heat alone, or a combination of heat and high pressure. Protein yields were compared, and digested peptides from the extracts were analyzed with MS. Combined heat and elevated pressure increased protein yield from human FF or FFPE aorta compared to matched tissues with heat alone (1.5-fold) or at RT (8.3-fold), resulting in more proteins identified and with more sequence coverage. The length of storage did adversely affect the quality of proteins from FF tissue. For long-term storage, aorta was preserved better with FFPE than FF alone. Periostin and MGF-E8 were demonstrated suitable for MRM assays from FFPE aorta. Combination of heat and high pressure is an effective method to extract proteins from FFPE aorta for downstream proteomics. This method opens the possibility for use of archival and often rare FFPE aortas and possibly other tissues available to proteomics for biomarker discovery and quantification. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Paraffin wax removal from metal injection moulded cocrmo alloy compact by solvent debinding process

    Science.gov (United States)

    Dandang, N. A. N.; Harun, W. S. W.; Khalil, N. Z.; Ahmad, A. H.; Romlay, F. R. M.; Johari, N. A.

    2017-10-01

    One of the most crucial and time consuming phase in metal injection moulding (MIM) process is “debinding”. These days, in metal injection moulding process, they had recounted that first debinding practice was depend on thermal binder degradation, which demanding more than 200 hours for complete removal of binder. Fortunately, these days world had introduced multi-stage debinding techniques to simplified the debinding time process. This research study variables for solvent debinding which are temperature and soaking time for samples made by MIM CoCrMo powder. Since wax as the key principal in the binder origination, paraffin wax will be removed together with stearic acid from the green bodies. Then, debinding process is conducted at 50, 60 and 70°C for 30-240 minutes. It is carried out in n-heptane solution. Percentage weight loss of the binder were measured. Lastly, scanning electron microscope (SEM) analysis and visual inspection were observed for the surface of brown compact. From the results, samples debound at 70°C exhibited a significant amount of binder loss; nevertheless, sample collapse, brittle surface and cracks were detected. But, at 60°C temperature and time of 4 hours proven finest results as it shows sufficient binder loss, nonappearance of surface cracks and easy to handle. Overall, binder loss is directly related to solvent debinding temperature and time.

  19. Complete solubilization of formalin-fixed, paraffin-embedded tissue may improve proteomic studies.

    Science.gov (United States)

    Shi, Shan-Rong; Taylor, Clive R; Fowler, Carol B; Mason, Jeffrey T

    2013-04-01

    Tissue-based proteomic approaches (tissue proteomics) are essential for discovering and evaluating biomarkers for personalized medicine. In any proteomics study, the most critical issue is sample extraction and preparation. This problem is especially difficult when recovering proteins from formalin-fixed, paraffin-embedded (FFPE) tissue sections. However, improving and standardizing protein extraction from FFPE tissue is a critical need because of the millions of archival FFPE tissues available in tissue banks worldwide. Recent progress in the application of heat-induced antigen retrieval principles for protein extraction from FFPE tissue has resulted in a number of published FFPE tissue proteomics studies. However, there is currently no consensus on the optimal protocol for protein extraction from FFPE tissue or accepted standards for quantitative evaluation of the extracts. Standardization is critical to ensure the accurate evaluation of FFPE protein extracts by proteomic methods such as reverse phase protein arrays, which is now in clinical use. In our view, complete solubilization of FFPE tissue samples is the best way to achieve the goal of standardizing the recovery of proteins from FFPE tissues. However, further studies are recommended to develop standardized protein extraction methods to ensure quantitative and qualitative reproducibility in the recovery of proteins from FFPE tissues. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Ornitocenosis of the Sursky pond and its close the surroundings

    International Nuclear Information System (INIS)

    Lacko, J.; Ambrus, B.; Fupso, A.

    2013-01-01

    The paper focuses on the qualitative-quantitative research of fishpond bird community of the Sursky and its surroundings as well as on analysis of seasonal population dynamics of the avifauna as well as on placing the determined species into environmental groups and guilds. Another object is the comparison of our results with recent work focused on research of bird communities on this site.

  1. Review of Ordered Anarchy: Jasay and his Surroundings

    Directory of Open Access Journals (Sweden)

    Aschwin de Wolf

    2009-02-01

    Full Text Available Anthony de Jasay is among the most important social thinkers of our time. His oeuvre offers a sustained critique of government and its defenders. In the book Ordered Anarchy: Jasay and His Surroundings, colleagues and friends pay tribute to the man in the form of an inspiring collection of essays.

  2. Linking disadvantaged housing areas to the surrounding city

    DEFF Research Database (Denmark)

    Stender, Marie

    Several disadvantaged social housing areas in Denmark are currently undergo-ing thorough physical refurbishments, aiming to integrate them better with the surrounding city. The ambition is to attract new users and residents by opening up the borders of the area and establish attractive, new...

  3. Ecological mechanisms linking protected areas to surrounding lands.

    Science.gov (United States)

    Hansen, Andrew J; DeFries, Ruth

    2007-06-01

    Land use is expanding and intensifying in the unprotected lands surrounding many of the world's protected areas. The influence of this land use change on ecological processes is poorly understood. The goal of this paper is to draw on ecological theory to provide a synthetic framework for understanding how land use change around protected areas may alter ecological processes and biodiversity within protected areas and to provide a basis for identifying scientifically based management alternatives. We first present a conceptual model of protected areas embedded within larger ecosystems that often include surrounding human land use. Drawing on case studies in this Invited Feature, we then explore a comprehensive set of ecological mechanisms by which land use on surrounding lands may influence ecological processes and biodiversity within reserves. These mechanisms involve changes in ecosystem size, with implications for minimum dynamic area, species-area effect, and trophic structure; altered flows of materials and disturbances into and out of reserves; effects on crucial habitats for seasonal and migration movements and population source/sink dynamics; and exposure to humans through hunting, poaching, exotics species, and disease. These ecological mechanisms provide a basis for assessing the vulnerability of protected areas to land use. They also suggest criteria for designing regional management to sustain protected areas in the context of surrounding human land use. These design criteria include maximizing the area of functional habitats, identifying and maintaining ecological process zones, maintaining key migration and source habitats, and managing human proximity and edge effects.

  4. The bird species of pandam wildlife park and the surrounding ...

    African Journals Online (AJOL)

    The effect of time of day as well as vegetation variables on bird species diversity in the park and surrounding farmlands was also conducted. 10 transects in each study site were surveyed twice between during the dry season and vegetation variables (trees, fingers, finger-rings two- hand, grazing, farming, canopy cover, ...

  5. Experiences during the decontamination process of areas surrounding to Fukushima

    International Nuclear Information System (INIS)

    Molina, G.

    2014-10-01

    In this work the experience gained during the decontamination of areas surrounding to Fukushima NPP, rugged during the earthquake and tsunami in 2011 and caused the contamination with fission products in these areas is described. Actions taken by the Japanese government are reported and some of the techniques used, the intervention levels and the progress made and disposal techniques considered are presented. (Author)

  6. Traditional Indian customs surrounding birth A review | Chalmers ...

    African Journals Online (AJOL)

    Since 1960, only a few studies have been made of traditional custOIns surrounding birth in Indian culture. Very few of these have described customs followed by Indians in South Africa. A review of these publications is presented here. Customs described include religious, social and psychological aspects of behaviour in ...

  7. Evaluation of two methods DNA extraction from formalin-fixed, paraffin-embedded tissues on non-optimal conditions

    International Nuclear Information System (INIS)

    Bustamante, Javier Andres; Astudillo, Miryam; Pazos, Alvaro Jairo; Bravo, Luis Eduardo

    2011-01-01

    Paraffin wax embedded tissues are an invaluable material for retrospective studies requiring the application of molecular analysis. Multiple methods are available to extract DNA from these kinds of samples. However, the most common methods are slow and the reagents often contribute to the fragmentation of genetic material. In order to optimize the procedure, two methods for DNA extraction from paraffin embedded tissue non-optimal conditions were used. 47 blocks containing paraffin-embedded biopsies of pleura, lung and pericardium from 24 patients (66.6% males) older than 18 years, with biopsy proven chronic granulomatous inflammation referred to the department of pathology at University Hospital of Valle between 2002 and 2007 were selected. Each sample was subjected to 10 cuts and was to two methods of DNA extraction: 1. conventional and 2. QIAamp - DNA mini kit. The efficiency of the extracted DNA was assessed by spectrophotometry and PCR amplification of a fragment of the housekeeping gene GAPDH. The concentration of DNA samples extracted by the conventional method was of 65.52 ng/Mu l ± 11.47 (mean ± SE) and the 260/280 absorbance ratio ranged between 0.52 and 2.30 the average concentration of DNA of the samples extracted by the commercial method was 60.89 ng/Mu l ± 6.02 (mean ± SE), with an absorbance that fluctuated between 0 and 2.64. The DNA obtained was amplified by PCR, of 47 samples extracted by methods, 25 and 23 respectively the GAPDH gene amplified successfully. The methods used to obtain DNA showed similar performance, highlighting the potential utility of both extraction methods for the retrospective studies from paraffin embedded tissues in unsuitable conditions.

  8. Preparation and characterization of form-stable paraffin/polyurethane composites as phase change materials for thermal energy storage

    International Nuclear Information System (INIS)

    Chen, Keping; Yu, Xuejiang; Tian, Chunrong; Wang, Jianhua

    2014-01-01

    Highlights: • Paraffin/polyurethane composite as form-stable phase change material was prepared by bulk polymerization. • Paraffin/polyurethane composite possesses typical character of dual phase transition. • Total latent heat of n-eicosane/PUPCM is as high as 141.2 J/g. • Maximum encapsulation ratio for n-octadecane/PUPCM composites is 25% w/w. - Abstract: Polyurethane phase change material (PUPCM) has been demonstrated to be effective solid–solid phase change material for thermal energy storage. However, the high cost and complex process on preparation of PUPCMs with high enthalpy and broad phase transition temperature range can prohibit industrial-scale applications. In this work, a series of novel form-stable paraffin/PUPCMs composites (n-octadecane/PUPCM, n-eicosane/PUPCM and paraffin wax/PUPCM) with high enthalpy and broad phase transition temperature range (20–65 °C) were directly synthesized via bulk polymerization. The composites were prepared at different mass fractions of n-octadecane (10, 20, 25, 30% w/w). The results indicated that the maximum encapsulation ratio for n-octadecane/PUPCM10000 composites was around 25% w/w. The chemical structure and crystalline properties of these composites were characterized by Fourier transform infrared spectroscopy (FT-IR), polarizing optical microscopy (POM), wide-angle X-ray diffraction (WAXD). Thermal properties and thermal reliability of the composites were determined using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). From DSC analysis, the composites showed a typical dual phase change temperature. The enthalpy for the composite with 25% w/w n-eicosane was as high as 141.2 J/g. TGA analysis indicated that the composites degraded at considerably high temperatures. The process of preparation of PUPCMs and their composites was very simple, inexpensive, environmental friendly and easy to process into desired shapes, which could find the promising applications in solar

  9. Evaluating the Environmental Fate of Short-Chain Chlorinated Paraffins (SCCPs) in the Nordic Environment Using a Dynamic Multimedia Model

    OpenAIRE

    Krogseth, Ingjerd Sunde; Breivik, Knut; Arnot, Jon A; Wania, Frank; Borgen, Anders; Schlabach, Martin

    2013-01-01

    Short chain chlorinated paraffins (SCCPs) raise concerns due to their potential for persistence, bioaccumulation, long-range transport and adverse effects. An understanding of their environmental fate remains limited, partly due to the complexity of the mixture. The purpose of this study was to evaluate whether a mechanistic, integrated, dynamic environmental fate and bioaccumulation multimedia model (CoZMoMAN) can reconcile what is known about environmental emissions and human exposure of SC...

  10. Using Paraffin PCM to Make Optical Communication Type of Payloads Thermally Self-Sufficient for Operation in Orion Crew Module

    Science.gov (United States)

    Choi, Michael K.

    2016-01-01

    An innovative concept of using paraffin phase change material with a melting point of 28 C to make Optical Communication type of payload thermally self-sufficient for operation in the Orion Crew Module is presented. It stores the waste heat of the payload and permits it to operate for about one hour by maintaining its temperature within the maximum operating limit. It overcomes the problem of relying on the availability of cold plate heat sink in the Orion Crew Module.

  11. Automated Analysis of Protein Expression and Gene Amplification within the Same Cells of Paraffin-Embedded Tumour Tissue

    Directory of Open Access Journals (Sweden)

    Timo Gaiser

    2010-01-01

    Full Text Available Background: The simultaneous detection of protein expression and gene copy number changes in patient samples, like paraffin-embedded tissue sections, is challenging since the procedures of immunohistochemistry (IHC and Fluorescence in situ Hybridization (FISH negatively influence each other which often results in suboptimal staining. Therefore, we developed a novel automated algorithm based on relocation which allows subsequent detection of protein content and gene copy number changes within the same cell.

  12. A comparison between DACC with chlorhexidine acetate-soaked paraffin gauze and foam dressing for skin graft donor sites.

    Science.gov (United States)

    Lee, Jun Won; Park, Seong Hoon; Suh, In Suck; Jeong, Hii Sun

    2018-01-02

    Retrograde infections often occur with excessive or incomplete drainage of exudate, or as a result of adherence of dressings to wounds. Dialkylcarbamoyl chloride (DACC) irreversibly binds to bacterial surfaces and physically removes bacteria when dressings are changed. Chlorhexidine acetate-soaked paraffin gauze provides a moist wound-healing environment. We hypothesise that when DACC is combined with chlorhexidine acetate-soaked paraffin gauze, wound healing times decrease. From January 2013 to June 2015, medical records were retrospectively evaluated in 60 patients who underwent split-thickness skin grafts (STSG). Patients were divided into two groups: a 'thick skin group' and a 'thin skin group'. These two groups were further subdivided into a control group, where conventional foam dressings were applied to wounds, and an experimental group, where chlorhexidine acetate-soaked paraffin gauze with DACC was applied (DACC group). We compared the wound healing time between these subgroups. Differences in infected wound healing times were also compared. The Mann-Whitney test was applied to compare wound healing times between groups. Epithelialisation duration was significantly shorter in the DACC group. The control group had longer wound healing times, regardless of wound size. In the thick skin group, the median healing duration was 12 days in the control subgroup, compared with 9.5 days in the DACC subgroup (p=0.049). In the thin skin subgroup, the median healing duration in the control group was 18 days, compared with 10 days in the DACC subgroup (p=0.013). Application of DACC and chlorhexidine acetate-soaked paraffin gauze to skin graft donor sites can shorten healing times and is effective in treating infected wounds.

  13. Validation of putative reference genes for normalization of Q-RT-PCR data from paraffin-embedded lymphoid tissue

    DEFF Research Database (Denmark)

    Green, Tina Marie; de Stricker, Karin; Møller, Michael Boe

    2009-01-01

    Normalization of quantitative reverse transcription-PCR (Q-RT-PCR) data to appropriate tissue-specific reference genes is an essential part of interpreting the results. This study aimed to determine the most appropriate reference genes for normalizing gene expressions in lymphatic tissue...... was 0.93 (Pnormalization with the appropriate reference genes. Thus, we show that formalin-fixed, paraffin-embedded lymphoid samples are suitable for Q-RT-PCR when using thoroughly validated reference genes....

  14. Preparation and flammability of high density polyethylene/paraffin/organophilic montmorillonite hybrids as a form stable phase change material

    International Nuclear Information System (INIS)

    Cai, Yibing; Hu, Yuan; Song, Lei; Kong, Qinghong; Yang, Rui; Zhang, Yinping; Chen, Zuyao; Fan, Weicheng

    2007-01-01

    A kind of form stable phase change material (PCM) based on high density polyethylene (HDPE), paraffin, organophilic montmorillonite (OMT) and intumescent flame retardant (IFR) hybrids is prepared by using a twin screw extruder technique. This kind of form stable PCM is made of paraffin as a dispersed phase change material and HDPE as a supporting material. The structure of the montmorillonite (MMT) and OMT is characterized by X-ray diffraction (XRD) and high resolution electron microscopy (HREM). The analysis indicates that the MMT is a kind of lamellar structure, and the structure does not change after organic modification. However, the structure of the hybrid is evidenced by the XRD and scanning electronic microscope (SEM). Its thermal stability, latent heat and flame retardant properties are given by the Thermogravimetry analysis (TGA), differential scanning calorimeter (DSC) method and cone calorimeter, respectively. Synergy is observed between the OMT and IFR. The XRD result indicates that the paraffin intercalates into the silicate layers of the OMT, thus forming a typically intercalated hybrid. The SEM investigation and DSC result show that the additives of OMT and IFR have hardly any effect on the HDPE/paraffin three dimensional netted structure and the latent heat. In TGA curves, although the onset of weight loss of flame-retardant form stable PCMs occur at a lower temperature than that of form stable PCM, flame-retardant form stable PCMs produce a large amount of char residue at 700 o C. The synergy between OMT and IFR leads to the decrease of the heat release rate (HRR), contributing to improvement of the flammability performance

  15. Proteome stability analysis of snap frozen, RNAlater preserved, and formalin-fixed paraffin-embedded human colon mucosal biopsies

    DEFF Research Database (Denmark)

    Bennike, Tue Bjerg; Kastaniegaard, Kenneth; Padurariu, Simona

    2016-01-01

    Large repositories of well characterized RNAlater preserved samples and formalin-fixed, paraffin-embedded samples have been generated worldwide. However, the impact on the proteome of the preservation methods remain poorly described. Therefore, we analyzed the impact on the proteome of preserving...... throughput gel free quantitative proteomics. The MS proteomics data have been deposited to the ProteomeXchange Consortium via the PRIDE partner repository with the dataset identifier PRIDE: PXD002029....

  16. Thermal neutron moderating device

    International Nuclear Information System (INIS)

    Takigami, Hiroyuki.

    1995-01-01

    In a thermal neutron moderating device, superconductive coils for generating magnetic fields capable of applying magnetic fields vertical to the longitudinal direction of a thermal neutron passing tube, and superconductive coils for magnetic field gradient for causing magnetic field gradient in the longitudinal direction of the thermal neutron passing tube are disposed being stacked at the outside of the thermal neutron passing tube. When magnetic field gradient is present vertically to the direction of a magnetic moment, thermal neutrons undergo forces in the direction of the magnetic field gradient in proportion to the magnetic moment. Then, the magnetic moment of the thermal neutrons is aligned with the direction vertical to the passing direction of the thermal neutrons, to cause the magnetic field gradient in the passing direction of the thermal neutrons. The speed of the thermal neutrons can be optionally selected and the wavelength can freely be changed by applying forces to the thermal neutrons and changing the extent and direction of the magnetic field gradient. Superconductive coils are used as the coils for generating magnetic fields and the magnetic field gradient in order to change extremely high energy of the thermal neutrons. (N.H.)

  17. Toward a Moderate Autoethnography

    Directory of Open Access Journals (Sweden)

    Sarah Stahlke Wall

    2016-10-01

    Full Text Available Autoethnography is an avant-garde method of qualitative inquiry that has captured the attention of an ever-increasing number of scholars from a variety of disciplines. Personal experience methods can offer a new and unique vantage point from which to make a contribution to social science yet, autoethnography has been criticized for being self-indulgent, narcissistic, introspective, and individualized. Methodological discussions about this method are polarized. As an autoethnographer and qualitative methodologist with an interest in personal experience methods, I have had the opportunity to review several autoethnographic manuscripts over the years. As my reviews accumulated, I began to see themes in my responses and it became apparent that I was advocating for an approach to autoethnography that lies in contrast to the frequently offered methodological polemics from philosophically divergent scholars. In this article, I draw from the reviews I have done to address topics such as applications and purposes for autoethnography, the degree of theory and analysis used within the method, data sources and dissemination of findings, and ethical issues. I then connect the concerns I see in the reviewed manuscripts to examples in the autoethnographic literature. Ultimately, I propose a moderate and balanced treatment of autoethnography that allows for innovation, imagination, and the representation of a range of voices in qualitative inquiry while also sustaining confidence in the quality, rigor, and usefulness of academic research.

  18. Vasculature surrounding a nodule: A novel lung cancer biomarker.

    Science.gov (United States)

    Wang, Xiaohua; Leader, Joseph K; Wang, Renwei; Wilson, David; Herman, James; Yuan, Jian-Min; Pu, Jiantao

    2017-12-01

    To investigate whether the vessels surrounding a nodule depicted on non-contrast, low-dose computed tomography (LDCT) can discriminate benign and malignant screen detected nodules. We collected a dataset consisting of LDCT scans acquired on 100 subjects from the Pittsburgh Lung Screening study (PLuSS). Fifty subjects were diagnosed with lung cancer and 50 subjects had suspicious nodules later proven benign. For the lung cancer cases, the location of the malignant nodule in the LDCT scans was known; while for the benign cases, the largest nodule in the LDCT scan was used in the analysis. A computer algorithm was developed to identify surrounding vessels and quantify the number and volume of vessels that were connected or near the nodule. A nonparametric receiver operating characteristic (ROC) analysis was performed based on a single nodule per subject to assess the discriminability of the surrounding vessels to provide a lung cancer diagnosis. Odds ratio (OR) were computed to determine the probability of a nodule being lung cancer based on the vessel features. The areas under the ROC curves (AUCs) for vessel count and vessel volume were 0.722 (95% CI=0.616-0.811, plung cancer group 9.7 (±9.6) compared to the non-lung cancer group 4.0 (±4.3) CONCLUSION: Our preliminary results showed that malignant nodules are often surrounded by more vessels compared to benign nodules, suggesting that the surrounding vessel characteristics could serve as lung cancer biomarker for indeterminate nodules detected during LDCT lung cancer screening using only the information collected during the initial visit. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Characterization of coke deposited on nano-sized Pt-Pd/H-beta spent during long-chain paraffin hydroisomerization

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, F.; Einicke, W.D.; Ficht, K.; Glaeser, R. [Leipzig Univ. (Germany). Inst. of Chemical Technology; Bertmer, M. [Leipzig Univ. (Germany). Inst. of Experimental Physics II; Kuchling, T. [Technische Univ. Bergakademie Freiberg (Germany). Inst. of Energy Process Engineering and Chemical Engineering

    2013-11-01

    The hydroisomerization of long-chain n-paraffins were studied in the temperature range 205- 230 C at p{sub H2}=50 bar using a bench scale trickle-bed continuous-flow reactor. The bimetallic catalysts consisted of mixtures of platinum and palladium supported on commercially available nano-sized zeolites Beta (n{sub Si}/n{sub Al} = 12 and 25) extruded with a binder ({gamma}-alumina). For hexadecane conversion, high yields to isomers (25 and 45 wt.% of mono- and multibranched isomers, respectively) without extensive cracking (>10 wt.%) were obtained at a conversion of 80 %. Long-term tests with C{sub 16}H{sub 34} and blends of solid n-paraffins for 30-60 days on stream clearly indicate that a minor loss in catalyst activity can easily be compensated by increasing the reaction temperature from 230 C to 235 C. The zeolite sample with a 'mild acidity' revealed low hydrocracking at isomerization yield up to 70 wt.% and high stability. Carbonaceous deposits formed during n-paraffin hydroisomerization were investigated by temperature-programmed oxidation, elemental analysis, ATR-FTIR and {sup 13}C MAS NMR spectroscopy showing the formation of low-temperature, hydrogen-rich coke. (orig.)

  20. Proteome stability analysis of snap frozen, RNAlater preserved, and formalin-fixed paraffin-embedded human colon mucosal biopsies

    Directory of Open Access Journals (Sweden)

    Tue Bjerg Bennike

    2016-03-01

    Full Text Available Large repositories of well characterized RNAlater preserved samples and formalin-fixed, paraffin-embedded samples have been generated worldwide. However, the impact on the proteome of the preservation methods remain poorly described. Therefore, we analyzed the impact on the proteome of preserving samples in RNAlater, and by formalin-fixation, paraffin-embedding on human soft tissue, using directly frozen samples as a control (“Comparing the proteome of snap frozen, RNAlater preserved, and formalin-fixed paraffin-embedded human tissue samples” [1]. We here report the data from the analysis. The comparative analysis was performed on 24 colon mucosa biopsies, extracted from the sigmoideum of two gastroenterologically healthy participants for the purpose of this study. A set of biopsies were additionally stored for 30 min at room temperature prior to formalin-fixation. The samples were analyzed by high throughput gel free quantitative proteomics. The MS proteomics data have been deposited to the ProteomeXchange Consortium via the PRIDE partner repository with the dataset identifier PRIDE: http://www.ebi.ac.uk/pride/archive/projects/PXD002029. Keywords: Human, Colon, Mucosa, RNAlater, FFPE, Snap-frozen, Stability, LC–MS, Proteomics

  1. Experimental and comparative study of the effect of paraffin oil and covering for solar ponds without saline water

    Energy Technology Data Exchange (ETDEWEB)

    Spyridonos, A V; Anagnostatos, G S; Novakovic, M M

    1989-01-01

    The effect of a superficial layer of paraffin or a plastic covering on the thermal storage efficiency of three kinds of non-saline solar pond has been investigated. Four small scale ponds were used for experimental measurements. These were: (1) a reference pond; (2) a pond divided horizontally into compartments separated by plastic sheets; (3) a pond with a superficial layer of paraffin and (4) a pond filled with hollow plastic cubes. Comparisons were made between these four ponds with and without plastic coverings, and with a layer of paraffin in addition on ponds 2 and 4. The rise in mean temperature of each pond during a number of heating cycles has been studied. A difference in mean temperature of the order of 10 to 20/sup 0/C was observed in each case between the beginning and end of the heating period and the temperature at the bottom of the pond after heating was in the range 30 to 50/sup 0/C. The results for these experimental ponds may be of use in the choice of full-size shallow ponds and may also give important indications for ponds of much greater depth.

  2. Polymerase chain reaction analysis for viruses in paraffin-embedded myocardium from dogs with dilated cardiomyopathy or myocarditis.

    Science.gov (United States)

    Maxson, T R; Meurs, K M; Lehmkuhl, L B; Magnon, A L; Weisbrode, S E; Atkins, C E

    2001-01-01

    To perform polymerase chain reaction (PCR) analysis on paraffin-embedded myocardium from dogs with dilated cardiomyopathy (DCM) and dogs with myocarditis to screen for canine parvovirus, adenovirus types 1 and 2, and herpesvirus. Myocardial specimens from 18 dogs with an antemortem diagnosis of DCM and 9 dogs with a histopathologic diagnosis of myocarditis were evaluated. Paraffin-embedded myocardial specimens were screened for viral genome by PCR analysis. Positive-control specimens were developed from cell cultures as well as paraffin-embedded tissue specimens from dogs with clinical and histopathologic diagnoses of viral infection with canine parvovirus, adenovirus types 1 and 2, and herpesvirus. The histologic characteristics of all myocardial specimens were classified regarding extent, location, and type of inflammation and fibrosis. Canine adenovirus type 1 was amplified from 1 specimen from a dog with DCM. Canine parvovirus, adenovirus type 2, and herpesvirus were not amplified from any myocardial specimens. Histologic analysis of specimens from dogs with DCM revealed variable amounts of fibrosis; myocardial inflammation was observed in 1 affected dog. Histopathologic analysis of specimens from dogs with myocarditis disclosed variable degrees of inflammation and fibrosis. Viral agents canine parvovirus, adenovirus types 1 and 2, and herpesvirus are not commonly associated with DCM or active myocarditis in dogs. Additional studies evaluating for nucleic acid from viruses that less commonly affect dogs or different types of infectious agents may be warranted to gain insight into the cause of DCM and myocarditis in dogs.

  3. Effects of Emulsifiers on Preparing Spherical Urea-Formaldehyde Paraffin Capsules Modified by β-Cyclodextrin for Energy Storage

    Directory of Open Access Journals (Sweden)

    Xin Yu

    2014-01-01

    Full Text Available Urea-formaldehyde (UF paraffin capsules (B-UPCS modified by β-cyclodextrin (β-CD were successfully prepared with excellent energy storage capacity using different emulsifiers. B-UPCS were characterized by FT-IR, DSC SEM, optical microscopy, and laser particle size distribution analyzer. The effects of different emulsifiers and the stirring rate of emulsion on the microstructure, average particle diameter, and the content of paraffin were discussed in details. The results show that OP-10 for use with PCMs as emulsifier has a better emulsifying capacity, thermal stability, and mechanical stirring stability than SDBS for use with PCMs as emulsifier. As a result, the optimum dosage of OP-10 was 3% to 7%, and the suitable stirring rate of emulsion was 7500 to 12500 rpm. At this time, the spherical particle diameter of B-UPCS was about 1.0 μm, the paraffin content was 78%, and the enthalpy of B-UPCS can reach 161.0 J/g.

  4. Methanogenic paraffin degradation proceeds via alkane addition to fumarate by 'Smithella' spp. mediated by a syntrophic coupling with hydrogenotrophic methanogens.

    Science.gov (United States)

    Wawrik, Boris; Marks, Christopher R; Davidova, Irene A; McInerney, Michael J; Pruitt, Shane; Duncan, Kathleen E; Suflita, Joseph M; Callaghan, Amy V

    2016-09-01

    Anaerobic microbial biodegradation of recalcitrant, water-insoluble substrates, such as paraffins, presents unique metabolic challenges. To elucidate this process, a methanogenic consortium capable of mineralizing long-chain n-paraffins (C28 -C50 ) was enriched from San Diego Bay sediment. Analysis of 16S rRNA genes indicated the dominance of Syntrophobacterales (43%) and Methanomicrobiales (26%). Metagenomic sequencing allowed draft genome assembly of dominant uncultivated community members belonging to the bacterial genus Smithella and the archaeal genera Methanoculleus and Methanosaeta. Five contigs encoding homologs of the catalytic subunit of alkylsuccinate synthase (assA) were detected. Additionally, mRNA transcripts for these genes, including a homolog binned within the 'Smithella' sp. SDB genome scaffold, were detected via RT-PCR, implying that paraffins are activated via 'fumarate addition'. Metabolic reconstruction and comparison with genome scaffolds of uncultivated n-alkane degrading 'Smithella' spp. are consistent with the hypothesis that syntrophically growing 'Smithella' spp. may achieve reverse electron transfer by coupling the reoxidation of ETFred to a membrane-bound FeS oxidoreductase functioning as an ETF:menaquinone oxidoreductase. Subsequent electron transfer could proceed via a periplasmic formate dehydrogenase and/or hydrogenase, allowing energetic coupling to hydrogenotrophic methanogens such as Methanoculleus. Ultimately, these data provide fundamental insight into the energy conservation mechanisms that dictate interspecies interactions salient to methanogenic alkane mineralization. © 2016 Society for Applied Microbiology and John Wiley & Sons Ltd.

  5. An Optimized Method of Metabolite Extraction from Formalin-Fixed Paraffin-Embedded Tissue for GC/MS Analysis.

    Science.gov (United States)

    Wojakowska, Anna; Marczak, Łukasz; Jelonek, Karol; Polanski, Krzysztof; Widlak, Piotr; Pietrowska, Monika

    2015-01-01

    Formalin-fixed paraffin-embedded (FFPE) tissue specimens constitute a highly valuable source of clinical material for retrospective molecular studies. However, metabolomic assessment of such archival material remains still in its infancy. Hence, there is an urgent need for efficient methods enabling extraction and profiling of metabolites present in FFPE tissue specimens. Here we demonstrate the methodology for isolation of primary metabolites from archival tissues; either fresh-frozen, formalin-fixed or formalin-fixed and paraffin-embedded specimens of mouse kidney were analysed and compared in this work. We used gas chromatography followed by mass spectrometry (GC/MS approach) to identify about 80 metabolites (including amino acids, saccharides, carboxylic acids, fatty acids) present in such archive material. Importantly, about 75% of identified compounds were detected in all three types of specimens. Moreover, we observed that fixation with formalin itself (and their duration) did not affect markedly the presence of particular metabolites in tissue-extracted material, yet fixation for 24h could be recommended as a practical standard. Paraffin embedding influenced efficiency of extraction, which resulted in reduced quantities of several compounds. Nevertheless, we proved applicability of FFPE specimens for non-targeted GS/MS-based profiling of tissue metabolome, which is of great importance for feasibility of metabolomics studies using retrospective clinical material.

  6. Optimization of Single- and Dual-Color Immunofluorescence Protocols for Formalin-Fixed, Paraffin-Embedded Archival Tissues.

    Science.gov (United States)

    Kajimura, Junko; Ito, Reiko; Manley, Nancy R; Hale, Laura P

    2016-02-01

    Performance of immunofluorescence staining on archival formalin-fixed paraffin-embedded human tissues is generally not considered to be feasible, primarily due to problems with tissue quality and autofluorescence. We report the development and application of procedures that allowed for the study of a unique archive of thymus tissues derived from autopsies of individuals exposed to atomic bomb radiation in Hiroshima, Japan in 1945. Multiple independent treatments were used to minimize autofluorescence and maximize fluorescent antibody signals. Treatments with NH3/EtOH and Sudan Black B were particularly useful in decreasing autofluorescent moieties present in the tissue. Deconvolution microscopy was used to further enhance the signal-to-noise ratios. Together, these techniques provide high-quality single- and dual-color fluorescent images with low background and high contrast from paraffin blocks of thymus tissue that were prepared up to 60 years ago. The resulting high-quality images allow the application of a variety of image analyses to thymus tissues that previously were not accessible. Whereas the procedures presented remain to be tested for other tissue types and archival conditions, the approach described may facilitate greater utilization of older paraffin block archives for modern immunofluorescence studies. © 2016 The Histochemical Society.

  7. Study of neutron moderation using the {sup 241}Am-Be spectrum with hydrogenated materials; Estudo da moderacao de neutrons utilizando o espectro de {sup 241}Am-Be com materiais hidrogenados

    Energy Technology Data Exchange (ETDEWEB)

    Santos, A.R.L.; Silva, F.S.; Martins, M.M.; Pereira, W.W., E-mail: aleiras@ird.gov.br [Instituto de Radioprotecao e Dosimetria (IRD/CNEN-RJ/LNMRI/LN), Rio de Janeiro, RJ (Brazil). Lab. de Neutrons; Freitas, B.M. [Coordenacao dos Programas de Pos-Graduacao em Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear; Tavares, D.Y.S. [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2014-07-01

    This work intends to assess materials for moderation of neutrons, trying to reduce the rate of H{sub p}(10) and H⁎p(10), reducing the effective dose of Occupationally Exposed Workers (OEW) who handle this source daily. The neutron spectra moderated by different materials was performed with a neutron source of {sup 241}Am-Be in an electronic positioning system, using a neutron spectrometry with Bonner Sphere at 50 cm from the center of source. The materials used for moderation were paraffin, silicone and Polyvinyl Chloride (PVC) resin ball. (author)

  8. Single-Nucleotide Polymorphism-Microarray Ploidy Analysis of Paraffin-Embedded Products of Conception in Recurrent Pregnancy Loss Evaluations.

    Science.gov (United States)

    Maslow, Bat-Sheva L; Budinetz, Tara; Sueldo, Carolina; Anspach, Erica; Engmann, Lawrence; Benadiva, Claudio; Nulsen, John C

    2015-07-01

    To compare the analysis of chromosome number from paraffin-embedded products of conception using single-nucleotide polymorphism (SNP) microarray with the recommended screening for the evaluation of couples presenting with recurrent pregnancy loss who do not have previous fetal cytogenetic data. We performed a retrospective cohort study including all women who presented for a new evaluation of recurrent pregnancy loss over a 2-year period (January 1, 2012, to December 31, 2013). All participants had at least two documented first-trimester losses and both the recommended screening tests and SNP microarray performed on at least one paraffin-embedded products of conception sample. Single-nucleotide polymorphism microarray identifies all 24 chromosomes (22 autosomes, X, and Y). Forty-two women with a total of 178 losses were included in the study. Paraffin-embedded products of conception from 62 losses were sent for SNP microarray. Single-nucleotide polymorphism microarray successfully diagnosed fetal chromosome number in 71% (44/62) of samples, of which 43% (19/44) were euploid and 57% (25/44) were noneuploid. Seven of 42 (17%) participants had abnormalities on recurrent pregnancy loss screening. The per-person detection rate for a cause of pregnancy loss was significantly higher in the SNP microarray (0.50; 95% confidence interval [CI] 0.36-0.64) compared with recurrent pregnancy loss evaluation (0.17; 95% CI 0.08-0.31) (P=.002). Participants with one or more euploid loss identified on paraffin-embedded products of conception were significantly more likely to have an abnormality on recurrent pregnancy loss screening than those with only noneuploid results (P=.028). The significance remained when controlling for age, number of losses, number of samples, and total pregnancies. These results suggest that SNP microarray testing of paraffin-embedded products of conception is a valuable tool for the evaluation of recurrent pregnancy loss in patients without prior fetal

  9. The ideology of moderated modernism in Serbian music and musicology

    Directory of Open Access Journals (Sweden)

    Medić Ivana

    2007-01-01

    Full Text Available The term ′moderated modernism′ has been current for quite some time in Serbian music historiography, but there have been only a few attempts to define it. I shall try to define the term, introduce some of its key concepts and features and demonstrate its applicability. Although moderated modernism was an international phenomenon which had divergent manifestations in various periods before and after the Second World War throughout Europe, my aim is to focus on the period between the decline of Socialist Realism and the ascent of post-modernism (roughly 1950 to 1980 in socialist Serbia, and to discuss the discourses and ideologies surrounding moderated modernism then and there.

  10. Ultrastructural relationship of the phagophore with surrounding organelles.

    Science.gov (United States)

    Biazik, Joanna; Ylä-Anttila, Päivi; Vihinen, Helena; Jokitalo, Eija; Eskelinen, Eeva-Liisa

    2015-01-01

    Phagophore nucleates from a subdomain of the endoplasmic reticulum (ER) termed the omegasome and also makes contact with other organelles such as mitochondria, Golgi complex, plasma membrane and recycling endosomes during its formation. We have used serial block face scanning electron microscopy (SB-EM) and electron tomography (ET) to image phagophore biogenesis in 3 dimensions and to determine the relationship between the phagophore and surrounding organelles at high resolution. ET was performed to confirm whether membrane contact sites (MCSs) are evident between the phagophore and those surrounding organelles. In addition to the known contacts with the ER, we identified MCSs between the phagophore and membranes from putative ER exit sites, late endosomes or lysosomes, the Golgi complex and mitochondria. We also show that one phagophore can have simultaneous MCSs with more than one organelle. Future membrane flux experiments are needed to determine whether membrane contacts also signify lipid translocation.

  11. Trajectories and Maneuvers of Surrounding Vehicles with Panoramic Camera Arrays

    DEFF Research Database (Denmark)

    Dueholm, Jacob Velling; Kristoffersen, Miklas Strøm; Satzoda, Ravi K.

    2016-01-01

    Vision-based research for intelligent vehicles have traditionally focused on specific regions around a vehicle, such as a front looking camera for, e.g., lane estimation. Traffic scenes are complex and vital information could be lost in unobserved regions. This paper proposes a framework that uses...... four visual sensors for a full surround view of a vehicle in order to achieve an understanding of surrounding vehicle behaviors. The framework will assist the analysis of naturalistic driving studies by automating the task of data reduction of the observed trajectories. To this end, trajectories...... are estimated using a vehicle detector together with a multiperspective optimized tracker in each view. The trajectories are transformed to a common ground plane, where they are associated between perspectives and analyzed to reveal tendencies around the ego-vehicle. The system is tested on sequences from 2.5 h...

  12. Mechanical Characteristics Analysis of Surrounding Rock on Anchor Bar Reinforcement

    Science.gov (United States)

    Gu, Shuan-cheng; Zhou, Pan; Huang, Rong-bin

    2018-03-01

    Through the homogenization method, the composite of rock and anchor bar is considered as the equivalent material of continuous, homogeneous, isotropic and strength parameter enhancement, which is defined as reinforcement body. On the basis of elasticity, the composite and the reinforcement are analyzed, Based on strengthening theory of surrounding rock and displacement equivalent conditions, the expression of reinforcement body strength parameters and mechanical parameters is deduced. The example calculation shows that the theoretical results are close to the results of the Jia-mei Gao[9], however, closer to the results of FLAC3D numerical simulation, it is proved that the model and surrounding rock reinforcement body theory are reasonable. the model is easy to analyze and calculate, provides a new way for determining reasonable bolt support parameters, can also provides reference for the stability analysis of underground cavern bolting support.

  13. Diversity of vascular plants of Piestany and surroundings (presentation)

    International Nuclear Information System (INIS)

    Penzesova, A.; Galusova, T.

    2013-01-01

    In this presentation is a summary of the results of floristic research aimed at determining diversity of vascular plants of Piestany and its surroundings. Plant taxa we determined using the designation keys. We have compiled a list of plant species occurring in the monitored area, we evaluated the selected botanical-phytogeographical characteristics of flora, we've put together a list of local protected, endangered and rare species and a list of local invasive and expansive species according to sources. (Authors)

  14. Methods of Assessing Noise Nuisance of Real Estate Surroundings

    Directory of Open Access Journals (Sweden)

    Szopińska Kinga

    2016-03-01

    Full Text Available Testing what factors create the market value of real estate is key information when preparing property valuations as well as other opinions and professional evaluations on the basis of which court verdicts or administrative decisions are made. One of the factors influencing the value of some real estate is the level of noise present in the surroundings, which can lead to the occurrence of noise nuisance negatively affecting social relations.

  15. Predicting response to primary chemotherapy: gene expression profiling of paraffin-embedded core biopsy tissue.

    Science.gov (United States)

    Mina, Lida; Soule, Sharon E; Badve, Sunil; Baehner, Fredrick L; Baker, Joffre; Cronin, Maureen; Watson, Drew; Liu, Mei-Lan; Sledge, George W; Shak, Steve; Miller, Kathy D

    2007-06-01

    Primary chemotherapy provides an ideal opportunity to correlate gene expression with response to treatment. We used paraffin-embedded core biopsies from a completed phase II trial to identify genes that correlate with response to primary chemotherapy. Patients with newly diagnosed stage II or III breast cancer were treated with sequential doxorubicin 75 mg/M2 q2 wks x 3 and docetaxel 40 mg/M2 weekly x 6; treatment order was randomly assigned. Pretreatment core biopsy samples were interrogated for genes that might correlate with pathologic complete response (pCR). In addition to the individual genes, the correlation of the Oncotype DX Recurrence Score with pCR was examined. Of 70 patients enrolled in the parent trial, core biopsies samples with sufficient RNA for gene analyses were available from 45 patients; 9 (20%) had inflammatory breast cancer (IBC). Six (14%) patients achieved a pCR. Twenty-two of the 274 candidate genes assessed correlated with pCR (p < 0.05). Genes correlating with pCR could be grouped into three large clusters: angiogenesis-related genes, proliferation related genes, and invasion-related genes. Expression of estrogen receptor (ER)-related genes and Recurrence Score did not correlate with pCR. In an exploratory analysis we compared gene expression in IBC to non-inflammatory breast cancer; twenty-four (9%) of the genes were differentially expressed (p < 0.05), 5 were upregulated and 19 were downregulated in IBC. Gene expression analysis on core biopsy samples is feasible and identifies candidate genes that correlate with pCR to primary chemotherapy. Gene expression in IBC differs significantly from noninflammatory breast cancer.

  16. Unmasking of complements using proteinase-K in formalin fixed paraffin embedded renal biopsies

    Directory of Open Access Journals (Sweden)

    R Nada

    2016-01-01

    Full Text Available Renal biopsy interpretation requires histopathology, direct immunofluorescence (DIF and electron microscopy. Formalin-fixed, paraffin-embedded tissue (FFPE sent for light microscopy can be used for DIF after antigen retrieval. However, complement staining has not been satisfactory. We standardized DIF using proteinase-K for antigen retrieval in FFPE renal biopsies. A pilot study was conducted on known cases of membranous glomerulonephritis (MGN, membranoproliferative type-1 (MPGN-1, immunoglobulin A nephropathy (IgAN, and anti-glomerular basement disease (anti-GBM. Immunofluorescence panel included fluorescein isothiocyanate (FITC conjugated IgG, IgA, IgM, complements (C3 and C1q, light chains (kappa, lambda and fibrinogen antibodies. After standardization of the technique, 75 renal biopsies and 43 autopsies cases were stained. Out of 43 autopsy cases, immune-complex mediated glomerulonephritis (GN was confirmed in 18 cases (Lupus nephritis-11, IgAN-6, MGN-1, complement-mediated dense deposit disease (DDD-1 and monoclonal diseases in 4 cases (amyloidosis-3, cast nephropathy-1. Immune-mediated injury was excluded in 17 cases (focal segmental glomerulosclerosis -3, crescentic GN-6 [pauci-immune-3, anti-GBM-3], thrombotic microangiopathy-5, atherosclerosis-3. Renal biopsies (n-75 where inadequate or no frozen sample was available; this technique classified 52 mesangiocapillary pattern as MPGN type-1-46, DDD-2 and (C3GN-4. Others were diagnosed as IgAN-3, lupus nephritis-2, MGN-4, diffuse proliferative glomerulonephritis (DPGN-1, Non-IC crescentic GN-1, monoclonal diseases-3. In nine cases, DIF on FFPE tissue could not help in making diagnosis. Proteinase-K enzymatic digestion of FFPE renal biopsies can unmask complements (both C3 and C1q in immune-complexes mediated and complement-mediated diseases. This method showed good results on autopsy tissues archived for as long as 15 years.

  17. Images of paraffin monolayer crystals with perfect contrast: minimization of beam-induced specimen motion

    Science.gov (United States)

    Glaeser, R.M.; McMullan, G.; Faruqi, A.R.; Henderson, R.

    2013-01-01

    Quantitative analysis of electron microscope images of organic and biological two-dimensional crystals has previously shown that the absolute contrast reached only a fraction of that expected theoretically from the electron diffraction amplitudes. The accepted explanation for this is that irradiation of the specimen causes beam-induced charging or movement, which in turn causes blurring of the image due to image or specimen movement. In this paper, we used three different approaches to try to overcome this image-blurring problem for monolayer crystals of paraffin. Our first approach was to use an extreme form of spotscan imaging, in which a single image was assembled on film by the successive illumination of up to 50,000 spots each of diameter around 7nm. The second approach was to use the Medipix II detector with its zero-noise readout to assemble a time-sliced series of images of the same area in which each frame from a movie with up to 400 frames had an exposure of only 500 electrons. In the third approach, we simply used a much thicker carbon support film to increase the physical strength and conductivity of the support. Surprisingly, the first two methods involving dose fractionation respectively in space or time produced only partial improvements in contrast whereas the third approach produced many virtually perfect images, in which the absolute contrast predicted from the electron diffraction amplitudes was observed in the images. We conclude that it is possible to obtain consistently almost perfect images of beam-sensitive specimens if they are attached to an appropriately strong and conductive support, but great care is needed in practice and the problem of how best to image ice-embedded biological structures in the absence of a strong, conductive support film requires more work. PMID:21185452

  18. Numerical Simulation on Zonal Disintegration in Deep Surrounding Rock Mass

    Directory of Open Access Journals (Sweden)

    Xuguang Chen

    2014-01-01

    Full Text Available Zonal disintegration have been discovered in many underground tunnels with the increasing of embedded depth. The formation mechanism of such phenomenon is difficult to explain under the framework of traditional rock mechanics, and the fractured shape and forming conditions are unclear. The numerical simulation was carried out to research the generating condition and forming process of zonal disintegration. Via comparing the results with the geomechanical model test, the zonal disintegration phenomenon was confirmed and its mechanism is revealed. It is found to be the result of circular fracture which develops within surrounding rock mass under the high geostress. The fractured shape of zonal disintegration was determined, and the radii of the fractured zones were found to fulfill the relationship of geometric progression. The numerical results were in accordance with the model test findings. The mechanism of the zonal disintegration was revealed by theoretical analysis based on fracture mechanics. The fractured zones are reportedly circular and concentric to the cavern. Each fracture zone ruptured at the elastic-plastic boundary of the surrounding rocks and then coalesced into the circular form. The geometric progression ratio was found to be related to the mechanical parameters and the ground stress of the surrounding rocks.

  19. Numerical simulation on zonal disintegration in deep surrounding rock mass.

    Science.gov (United States)

    Chen, Xuguang; Wang, Yuan; Mei, Yu; Zhang, Xin

    2014-01-01

    Zonal disintegration have been discovered in many underground tunnels with the increasing of embedded depth. The formation mechanism of such phenomenon is difficult to explain under the framework of traditional rock mechanics, and the fractured shape and forming conditions are unclear. The numerical simulation was carried out to research the generating condition and forming process of zonal disintegration. Via comparing the results with the geomechanical model test, the zonal disintegration phenomenon was confirmed and its mechanism is revealed. It is found to be the result of circular fracture which develops within surrounding rock mass under the high geostress. The fractured shape of zonal disintegration was determined, and the radii of the fractured zones were found to fulfill the relationship of geometric progression. The numerical results were in accordance with the model test findings. The mechanism of the zonal disintegration was revealed by theoretical analysis based on fracture mechanics. The fractured zones are reportedly circular and concentric to the cavern. Each fracture zone ruptured at the elastic-plastic boundary of the surrounding rocks and then coalesced into the circular form. The geometric progression ratio was found to be related to the mechanical parameters and the ground stress of the surrounding rocks.

  20. Enhanced sources of acoustic power surrounding AR 11429

    International Nuclear Information System (INIS)

    Donea, Alina; Hanson, Christopher

    2013-01-01

    Multi-frequency power maps of the local acoustic oscillations show acoustic enhancements (''acoustic-power halos'') at high frequencies surrounding large active region. Computational seismic holography reveals a high-frequency ''acoustic-emission halo'', or ''seismic glory'' surrounding large active regions. In this study, we have applied computational seismic holography to map the seismic seismic source density surrounding AR 11429. Studies of HMI/SDO Doppler data, shows that the ''acoustic halos'' and the ''seismic glories'' are prominent at high frequencies 5–8 mHz. We investigate morphological properties of acoustic-power and acoustic emission halos around an active region to see if they are spatially correlated. Details about the local magnetic field from vectormagnetograms of AR 11429 are included. We identify a 15'' region of seismic deficit power (dark moat) shielding the white-light boundary of the active region. The size of the seismic moat is related to region of intermediate magnetic field strength. The acoustic moat is circled by the halo of enhanced seismic amplitude as well as enhanced seismic emission. Overall, the results suggest that features are related. However, if we narrow the frequency band to 5.5 – 6.5 mHz, we find that the seismic source density dominates over the local acoustic power, suggesting the existence of sources that emit more energy downward into the solar interior than upward toward the solar surface.

  1. Tissue reaction surrounding miniscrews for orthodontic anchorage: An animal experiment

    Directory of Open Access Journals (Sweden)

    Stephanie Shih-Hsuan Chen

    2012-03-01

    Results and conclusions: (1 Tissue surrounding roots damaged by a miniscrew showed a significant inflammatory response. (2 Root resorption was occasionally observed after 3 weeks following insertion of a miniscrew even if the miniscrew was not in direct contact with the root. (3 Root repair was noted with a cementoblast lining along the resorption surface at as early as 3 weeks after miniscrew insertion. Alveolar bone filled in the lesion when the root damage was large so that the contour of the alveolar bone followed that of the damaged root, with the width of the periodontal ligament space being maintained. (4 Stable miniscrews were mainly those which did not contact adjacent roots, and for which the surrounding tissue showed only a small inflammatory response with some extent of direct bone contact around the miniscrew. On the contrary, most of the failed miniscrews were those which had direct contact with adjacent roots, and which exhibited severe tissue inflammation and were covered by thick layers of soft tissue. Failure was detected 3 weeks after insertion. Surprisingly, the epithelial lining surrounding the miniscrews might not have spontaneously resolved 6 weeks after screw removal. Persistent infection in the sinus tract was noted, and this would require attention.

  2. A permeability barrier surrounds taste buds in lingual epithelia

    Science.gov (United States)

    Dando, Robin; Pereira, Elizabeth; Kurian, Mani; Barro-Soria, Rene; Chaudhari, Nirupa

    2014-01-01

    Epithelial tissues are characterized by specialized cell-cell junctions, typically localized to the apical regions of cells. These junctions are formed by interacting membrane proteins and by cytoskeletal and extracellular matrix components. Within the lingual epithelium, tight junctions join the apical tips of the gustatory sensory cells in taste buds. These junctions constitute a selective barrier that limits penetration of chemosensory stimuli into taste buds (Michlig et al. J Comp Neurol 502: 1003–1011, 2007). We tested the ability of chemical compounds to permeate into sensory end organs in the lingual epithelium. Our findings reveal a robust barrier that surrounds the entire body of taste buds, not limited to the apical tight junctions. This barrier prevents penetration of many, but not all, compounds, whether they are applied topically, injected into the parenchyma of the tongue, or circulating in the blood supply, into taste buds. Enzymatic treatments indicate that this barrier likely includes glycosaminoglycans, as it was disrupted by chondroitinase but, less effectively, by proteases. The barrier surrounding taste buds could also be disrupted by brief treatment of lingual tissue samples with DMSO. Brief exposure of lingual slices to DMSO did not affect the ability of taste buds within the slice to respond to chemical stimulation. The existence of a highly impermeable barrier surrounding taste buds and methods to break through this barrier may be relevant to basic research and to clinical treatments of taste. PMID:25209263

  3. A permeability barrier surrounds taste buds in lingual epithelia.

    Science.gov (United States)

    Dando, Robin; Pereira, Elizabeth; Kurian, Mani; Barro-Soria, Rene; Chaudhari, Nirupa; Roper, Stephen D

    2015-01-01

    Epithelial tissues are characterized by specialized cell-cell junctions, typically localized to the apical regions of cells. These junctions are formed by interacting membrane proteins and by cytoskeletal and extracellular matrix components. Within the lingual epithelium, tight junctions join the apical tips of the gustatory sensory cells in taste buds. These junctions constitute a selective barrier that limits penetration of chemosensory stimuli into taste buds (Michlig et al. J Comp Neurol 502: 1003-1011, 2007). We tested the ability of chemical compounds to permeate into sensory end organs in the lingual epithelium. Our findings reveal a robust barrier that surrounds the entire body of taste buds, not limited to the apical tight junctions. This barrier prevents penetration of many, but not all, compounds, whether they are applied topically, injected into the parenchyma of the tongue, or circulating in the blood supply, into taste buds. Enzymatic treatments indicate that this barrier likely includes glycosaminoglycans, as it was disrupted by chondroitinase but, less effectively, by proteases. The barrier surrounding taste buds could also be disrupted by brief treatment of lingual tissue samples with DMSO. Brief exposure of lingual slices to DMSO did not affect the ability of taste buds within the slice to respond to chemical stimulation. The existence of a highly impermeable barrier surrounding taste buds and methods to break through this barrier may be relevant to basic research and to clinical treatments of taste. Copyright © 2015 the American Physiological Society.

  4. INTERACTIONS OF THE INFRARED BUBBLE N4 WITH ITS SURROUNDINGS

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Hong-Li; Li, Jin-Zeng; Yuan, Jing-Hua; Huang, Maohai; Huang, Ya-Fang; Zhang, Si-Ju [National Astronomical Observatories, Chinese Academy of Sciences, 20A Datun Road, Chaoyang District, Beijing 100012 (China); Wu, Yuefang [Department of Astronomy, Peking University, 100871 Beijing (China); Liu, Tie [Korea Astronomy and Space Science Institute 776, Daedeokdae-ro, Yuseong-gu, Daejeon, 305-348 (Korea, Republic of); Dubner, G.; Paron, S.; Ortega, M. E. [1Instituto de Astronomía y Física del Espacio (IAFE, CONICET-UBA), CC 67, Suc. 28, 1428 Buenos Aires (Argentina); Molinari, Sergio [Istituto di Astrofisica e Planetologia Spaziali—IAPS, Istituto Nazionale di Astrofisica—INAF, via Fosso del Cavaliere 100, I-00133 Roma (Italy); Zavagno, Annie; Samal, Manash R., E-mail: hlliu@nao.cas.cn [Aix Marseille Universit, CNRS, LAM (Laboratoire d’Astrophysique de Marseille) UMR 7326, F-13388, Marseille (France)

    2016-02-10

    The physical mechanisms that induce the transformation of a certain mass of gas in new stars are far from being well understood. Infrared bubbles associated with H ii regions have been considered to be good samples for investigating triggered star formation. In this paper we report on the investigation of the dust properties of the infrared bubble N4 around the H ii region G11.898+0.747, analyzing its interaction with its surroundings and star formation histories therein, with the aim of determining the possibility of star formation triggered by the expansion of the bubble. Using Herschel PACS and SPIRE images with a wide wavelength coverage, we reveal the dust properties over the entire bubble. Meanwhile, we are able to identify six dust clumps surrounding the bubble, with a mean size of 0.50 pc, temperature of about 22 K, mean column density of 1.7 × 10{sup 22} cm{sup −2}, mean volume density of about 4.4 × 10{sup 4} cm{sup −3}, and a mean mass of 320 M{sub ⊙}. In addition, from PAH emission seen at 8 μm, free–free emission detected at 20 cm, and a probability density function in special regions, we could identify clear signatures of the influence of the H ii region on the surroundings. There are hints of star formation, though further investigation is required to demonstrate that N4 is the triggering source.

  5. Blooming Trees: Substructures and Surrounding Groups of Galaxy Clusters

    Science.gov (United States)

    Yu, Heng; Diaferio, Antonaldo; Serra, Ana Laura; Baldi, Marco

    2018-06-01

    We develop the Blooming Tree Algorithm, a new technique that uses spectroscopic redshift data alone to identify the substructures and the surrounding groups of galaxy clusters, along with their member galaxies. Based on the estimated binding energy of galaxy pairs, the algorithm builds a binary tree that hierarchically arranges all of the galaxies in the field of view. The algorithm searches for buds, corresponding to gravitational potential minima on the binary tree branches; for each bud, the algorithm combines the number of galaxies, their velocity dispersion, and their average pairwise distance into a parameter that discriminates between the buds that do not correspond to any substructure or group, and thus eventually die, and the buds that correspond to substructures and groups, and thus bloom into the identified structures. We test our new algorithm with a sample of 300 mock redshift surveys of clusters in different dynamical states; the clusters are extracted from a large cosmological N-body simulation of a ΛCDM model. We limit our analysis to substructures and surrounding groups identified in the simulation with mass larger than 1013 h ‑1 M ⊙. With mock redshift surveys with 200 galaxies within 6 h ‑1 Mpc from the cluster center, the technique recovers 80% of the real substructures and 60% of the surrounding groups; in 57% of the identified structures, at least 60% of the member galaxies of the substructures and groups belong to the same real structure. These results improve by roughly a factor of two the performance of the best substructure identification algorithm currently available, the σ plateau algorithm, and suggest that our Blooming Tree Algorithm can be an invaluable tool for detecting substructures of galaxy clusters and investigating their complex dynamics.

  6. [Comparison of two different real-time PCR systems in postmortem diagnosis of tuberculosis in paraffin-embedded tissues].

    Science.gov (United States)

    Yağmur, Gülhan; Albayrak, Nurhan; Daş, Taner; Yıldırım, Muzaffer; Ozgün, Ayşe; Büyük, Yalçın

    2014-10-01

    Tuberculosis (TB) is one of those infections with high morbidity and mortality in all around the world. Hundreds of people died from this disease without diagnosed or due to resistant strains in Turkey. Therefore, it is important to identify postmortem cases who have died from tuberculosis. Molecular methods have been widely used as well as conventional methods in the diagnosis of tuberculosis. The aim of this study was to compare the two different real-time polymerase chain reaction (Rt-PCR) system in the postmortem diagnosis of Mycobacterium tuberculosis infections in paraffin-embedded tissues. A total of 40 paraffin-embedded tissue samples [lung (n= 35), brain (n= 2), heart (n= 2), lymph node (n= 1)] in which histopathologic findings consistent with TB (necrotizing granulomatous inflammation, gelatinous caseous pneumonia, necrotic fibrous nodul) obtained from 37 autopsy cases (31 male, 6 female; age range: 25-85 yrs) were included in the study. Paraffin-embedded tissues were deparafinized with xylene and ethyl alcohol and then DNA isolation was done with QIAsymphony DSP Virus/Pathogen Midi kit in the QIAsymphony device. DNA amplification process was performed by Rt-PCR using the kit Artus® M. tuberculosis RG-PCR in the Rotor-Gene® Q device (Qiagen, Germany). Likewise, after deparafinization process, samples placed in the cartridge and isolation and Rt-PCR was performed by Xpert® MTB/RIF (Cepheid, USA) system, simultaneosly. Seventeen and 20 out of the 40 paraffin-embedded tissues yielded positive results with Qiagen and Xpert system, respectively. M.tuberculosis DNA was found positive in 13 (32.5%) and negative in 16 (40%) of the samples by both of the systems, exhibiting 72.5% (29/40) of concordance. On the other hand, seven (17.5%) samples that were positive with Xpert system yielded negative result with the Qiagen, while four (10%) samples that were positive with Qiagen yielded negative result with the Xpert system. Of the 20 positive cases detected with

  7. Earthquakes in Switzerland and surrounding regions during 2007

    Energy Technology Data Exchange (ETDEWEB)

    Baer, M.; Deichmann, N.; Clinton, J.; Husen, S.; Faeh, D.; Giardini, D.; Kaestli, P.; Kradolfer, U.; Wiemer, S

    2008-12-15

    This report of the Swiss Seismological Service summarizes the seismic activity in Switzerland and surrounding regions during 2007. During this period, 531 earthquakes and 92 quarry blasts were detected and located in the region under consideration. Of these earthquakes, 30 are aftershocks of the stimulation of a proposed geothermal reservoir beneath the city of Basel in December of 2006. With 20 events with {mu}{sub {iota}} {>=} 2.5, four of which were artificially induced, the seismic activity in the year 2007 was far below the average over the previous 32 years. (author)

  8. Isoperimetric inequalities in surround system and space science

    OpenAIRE

    JiaJin Wen; Jun Yuan; ShanHe Wu

    2016-01-01

    Abstract By means of the algebraic, analysis, convex geometry, computer, and inequality theories we establish the following isoperimetric inequality in the centered 2-surround system S ( 2 ) { P , Γ , l } $S^{(2)} \\{P,\\varGamma ,l \\}$ : ( 1 | Γ | ∮ Γ r ¯ P p ) 1 / p ⩽ | Γ | 4 π sin l π | Γ | [ csc l π | Γ | + cot 2 l π | Γ | ln ( tan l π | Γ | + sec l π | Γ | ) ] , ∀ p ⩽ − 2 . $$\\begin{aligned}& \\biggl(\\frac{1}{|\\varGamma |} \\oint_{\\varGamma }\\bar{r}_{P}^{p} \\biggr)^{1/p}\\leqslant\\frac{|\\varG...

  9. Induced radioactivity in a 4 MW target and its surroundings

    CERN Document Server

    Agosteo, Stefano; Otto, Thomas; Silari, Marco

    2003-01-01

    An important aspect of a future CERN Neutrino Factory is the material activation arising from a 2.2 GeV, 4 MW proton beam striking a mercury target. An estimation of the hadronic inelastic interactions and the production of residual nuclei in the target, the magnetic horn, the decay tunnel, the surrounding rock and a downstream dump was performed by the Monte Carlo hadronic cascade code FLUKA. The aim was both to assess the dose equivalent rate to be expected during maintenance work and to evaluate the amount of residual radioactivity, which will have to be disposed of after the facility has ceased operation.

  10. Mutual seismic interaction between tunnels and the surrounding granular soil

    Directory of Open Access Journals (Sweden)

    Mohamed Ahmed Abdel-Motaal

    2014-12-01

    Study results show that the maximum exerted straining actions in tunnel lining are directly proportional to the relative stiffness between tunnel and surrounding soil (lining thickness and soil shear modulus. Moreover, it is highly affected by the peak ground acceleration and the tunnel location (embedment depth. A comprehensive study is performed to show the effect of tunnel thickness and tunnel diameter on both the induced bending moment and lining deformation. In general, it is concluded that seismic analysis should be considered in regions subjected to peak ground acceleration greater than 0.15g.

  11. Earthquakes in Switzerland and surrounding regions during 2007

    International Nuclear Information System (INIS)

    Baer, M.; Deichmann, N.; Clinton, J.; Husen, S.; Faeh, D.; Giardini, D.; Kaestli, P.; Kradolfer, U.; Wiemer, S.

    2008-01-01

    This report of the Swiss Seismological Service summarizes the seismic activity in Switzerland and surrounding regions during 2007. During this period, 531 earthquakes and 92 quarry blasts were detected and located in the region under consideration. Of these earthquakes, 30 are aftershocks of the stimulation of a proposed geothermal reservoir beneath the city of Basel in December of 2006. With 20 events with Μ ι ≥ 2.5, four of which were artificially induced, the seismic activity in the year 2007 was far below the average over the previous 32 years. (author)

  12. Diversity of vascular plants of Piestany and surroundings

    International Nuclear Information System (INIS)

    Penzesova, A.; Galusova, T.

    2013-01-01

    In the present work is a summary of the results of floristic research aimed at determining diversity of vascular plants of Piestany and its surroundings. Plant taxa we determined using the designation keys. We have compiled a list of plant species occurring in the monitored area, we evaluated the selected botanical-phytogeographical characteristics of flora, we've put together a list of local protected, endangered and rare species and a list of local invasive and expansive species according to sources. (Authors)

  13. One Japanese case on taxation surrounding foreign trust

    OpenAIRE

    SUZUKI, Yuya

    2015-01-01

    Taxation surrounding trust at cross-border situation is paid attention to byworldwide basis. Japan is not exception. According to recent Japanesejurisprudence, where a trust had been established in accordance with State law ofNew Jersey, the U.S., it was disputed whether or not the act settling that trust fellwithin “shintaku koui (an act of trust)” and one of the related members, who had beena minor child at that time, fell within “jyueki sha (beneficiary)” under JapaneseInheritance Tax Act....

  14. Effective melanin depigmentation of human and murine ocular tissues: an improved method for paraffin and frozen sections.

    Directory of Open Access Journals (Sweden)

    Caroline Manicam

    Full Text Available PURPOSE: The removal of excessive melanin pigments that obscure ocular tissue morphology is important to address scientific questions and for differential diagnosis of ocular tumours based on histology. Thus, the goal of the present study was to establish an effective and fast melanin bleaching method for paraffin and frozen mouse and human ocular tissues. METHODS: Paraffin-embedded and frozen ocular specimens from mice and human donors were subjected to bleaching employing two methods. The first employed potassium permanganate (KMnO4 with oxalic acid, and the second 10% hydrogen peroxide (H2O2. To determine optimal bleaching conditions, depigmentation was carried out at various incubation times. The effect of diluents used for 10% H2O2 was assessed using phosphate-buffered saline (PBS, and deionized water. Three different slide types and two fixatives, which were ice-cold acetone with 80% methanol, and 4% paraformaldehyde (PFA were used to determine the optimal conditions for better tissue adherence during bleaching. All tissues were stained in hematoxylin and eosin for histological evaluation. RESULTS: Optimal bleaching was achieved using warm 10% H2O2 diluted in PBS at 65°C for 120 minutes. Chromium-gelatin-coated slides prevented tissue detachment. Adherence of cryosections was also improved with post-fixation using 4% PFA and overnight air-drying at RT after cryosectioning. Tissue morphology was preserved under these conditions. Conversely, tissues bleached in KMnO4/oxalic acid demonstrated poor depigmentation with extensive tissue damage. CONCLUSIONS: Warm dilute H2O2 at 65°C for 120 minutes rapidly and effectively bleached both cryo- and paraffin sections of murine and human ocular tissues.

  15. Effective melanin depigmentation of human and murine ocular tissues: an improved method for paraffin and frozen sections.

    Science.gov (United States)

    Manicam, Caroline; Pitz, Susanne; Brochhausen, Christoph; Grus, Franz H; Pfeiffer, Norbert; Gericke, Adrian

    2014-01-01

    The removal of excessive melanin pigments that obscure ocular tissue morphology is important to address scientific questions and for differential diagnosis of ocular tumours based on histology. Thus, the goal of the present study was to establish an effective and fast melanin bleaching method for paraffin and frozen mouse and human ocular tissues. Paraffin-embedded and frozen ocular specimens from mice and human donors were subjected to bleaching employing two methods. The first employed potassium permanganate (KMnO4) with oxalic acid, and the second 10% hydrogen peroxide (H2O2). To determine optimal bleaching conditions, depigmentation was carried out at various incubation times. The effect of diluents used for 10% H2O2 was assessed using phosphate-buffered saline (PBS), and deionized water. Three different slide types and two fixatives, which were ice-cold acetone with 80% methanol, and 4% paraformaldehyde (PFA) were used to determine the optimal conditions for better tissue adherence during bleaching. All tissues were stained in hematoxylin and eosin for histological evaluation. Optimal bleaching was achieved using warm 10% H2O2 diluted in PBS at 65°C for 120 minutes. Chromium-gelatin-coated slides prevented tissue detachment. Adherence of cryosections was also improved with post-fixation using 4% PFA and overnight air-drying at RT after cryosectioning. Tissue morphology was preserved under these conditions. Conversely, tissues bleached in KMnO4/oxalic acid demonstrated poor depigmentation with extensive tissue damage. Warm dilute H2O2 at 65°C for 120 minutes rapidly and effectively bleached both cryo- and paraffin sections of murine and human ocular tissues.

  16. Characterization of paraffin based breast tissue equivalent phantom using a CdTe detector pulse height analysis.

    Science.gov (United States)

    Cubukcu, Solen; Yücel, Haluk

    2016-12-01

    In this study, paraffin was selected as a base material and mixed with different amounts of CaSO 4 ·2H 2 O and H 3 BO 3 compounds in order to mimic breast tissue. Slab phantoms were produced with suitable mixture ratios of the additives in the melted paraffin. Subsequently, these were characterized in terms of first half-value layer (HVL) in the mammographic X-ray range using a pulse-height spectroscopic analysis with a CdTe detector. Irradiations were performed in the energy range of 23-35 kV p under broad beam conditions from Mo/Mo and Mo/Rh target/filter combinations. X-ray spectra were acquired with a CdTe detector without and with phantom material interposition in increments of 1 cm thickness and then evaluated to obtain the transmission data. The net integral areas of the spectra for the slabs were used to plot the transmission curves and these curves were fitted to the Archer model function. The results obtained for the slabs were compared with those of standard mammographic phantoms such as CIRS BR series phantoms and polymethylmethacrylate plates (PMMA). From the evaluated transmission curves, the mass attenuation coefficients and HVLs of some mixtures are close to those of the commercially available standard mammography phantoms. Results indicated that when a suitable proportion of H 3 BO 3 and CaSO 4 ·2H 2 O is added to the paraffin, the resulting material may be a good candidate for a breast tissue equivalent phantom.

  17. Relative developmental toxicity of short-chain chlorinated paraffins in Zebrafish (Danio rerio) embryos.

    Science.gov (United States)

    Liu, Lihua; Li, Yifan; Coelhan, Mehmet; Chan, Hing Man; Ma, Wanli; Liu, Liyan

    2016-12-01

    Short-chain chlorinated paraffins (SCCPs) are ubiquitous in the environment and might cause adverse environmental and human health effects. Little is known about the relative toxicity of different SCCP compounds especially during development. The objective of this study was to characterize and compare effects of seven SCCP groups at environmentally relevant levels, using a zebrafish (Danio rerio) model. Observations on malformation, survival rates at 96 h post fertilization (hpf), and hatching rates at 72 hpf indicated that the C 10- groups (C 10 H 18 Cl 4 , 1,2,5,6,9,10-C 10 H 16 Cl 6 and C 10 H 15 Cl 7 ) were more toxic than the C 12- groups (C 12 H 22 Cl 4 , C 12 H 19 Cl 7 and 1,1,1,3,10,12,12,12-C 12 H 18 Cl 8 ) and Cereclor 63L. The C 10- groups were also more potent than C 12- groups and Cereclor 63L in decreasing thyroid hormone levels. Among the three compounds within the C 10- group, the compounds with less chlorine content had stronger effects on sub-lethal malformations but less effects on triiodothyronine (T3) and tetraiodothyronine (T4). Only C 10 H 18 Cl 4 significantly decreased the mRNA expression of tyr, ttr, dio2 and dio3 at a dose-dependent manner suggesting that the specific mode of actions differ with different congeners. The mechanisms of disruption of thyroid status by different SCCPs could be different. C 10 H 18 Cl 4 might inhibit T3 production through the inhibition effect on dio2. These results indicate that SCCP exposure could alter gene expression in the hypothalamic-pituitary-thyroid (HPT) axis and thyroid hormone levels. The mechanisms of disruption of thyroid status by different SCCPs could be different. Our results on the relative developmental toxicities of SCCPs will be useful to reach a better understanding of SCCP toxicity supporting environmental risk evaluation and regulation and used as a guidance for environmental monitoring of SCCPs in the future. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Whole-genome gene expression profiling of formalin-fixed, paraffin-embedded tissue samples.

    Directory of Open Access Journals (Sweden)

    Craig April

    2009-12-01

    Full Text Available We have developed a gene expression assay (Whole-Genome DASL, capable of generating whole-genome gene expression profiles from degraded samples such as formalin-fixed, paraffin-embedded (FFPE specimens.We demonstrated a similar level of sensitivity in gene detection between matched fresh-frozen (FF and FFPE samples, with the number and overlap of probes detected in the FFPE samples being approximately 88% and 95% of that in the corresponding FF samples, respectively; 74% of the differentially expressed probes overlapped between the FF and FFPE pairs. The WG-DASL assay is also able to detect 1.3-1.5 and 1.5-2 -fold changes in intact and FFPE samples, respectively. The dynamic range for the assay is approximately 3 logs. Comparing the WG-DASL assay with an in vitro transcription-based labeling method yielded fold-change correlations of R(2 approximately 0.83, while fold-change comparisons with quantitative RT-PCR assays yielded R(2 approximately 0.86 and R(2 approximately 0.55 for intact and FFPE samples, respectively. Additionally, the WG-DASL assay yielded high self-correlations (R(2>0.98 with low intact RNA inputs ranging from 1 ng to 100 ng; reproducible expression profiles were also obtained with 250 pg total RNA (R(2 approximately 0.92, with approximately 71% of the probes detected in 100 ng total RNA also detected at the 250 pg level. When FFPE samples were assayed, 1 ng total RNA yielded self-correlations of R(2 approximately 0.80, while still maintaining a correlation of R(2 approximately 0.75 with standard FFPE inputs (200 ng.Taken together, these results show that WG-DASL assay provides a reliable platform for genome-wide expression profiling in archived materials. It also possesses utility within clinical settings where only limited quantities of samples may be available (e.g. microdissected material or when minimally invasive procedures are performed (e.g. biopsied specimens.

  19. Moderate Secularism and Multicultural Equality

    DEFF Research Database (Denmark)

    Lægaard, Sune

    2008-01-01

    Tariq Modood argues that European states are only ‘moderately secular' and that this kind of secularism is compatible with public accommodation of religious groups and provides a model of Muslim integration appropriate for European states. Although attention to the fact of moderate secularism...... provides a response to a prominent argument against multicultural accommodation of religious minorities, what is really at stake in discussions of multiculturalism and secularism are political principles. Modood's case for accommodation of Muslims along the lines of moderate secularism presupposes...

  20. Doing statistical mediation and moderation

    CERN Document Server

    Jose, Paul E

    2013-01-01

    Written in a friendly, conversational style, this book offers a hands-on approach to statistical mediation and moderation for both beginning researchers and those familiar with modeling. Starting with a gentle review of regression-based analysis, Paul Jose covers basic mediation and moderation techniques before moving on to advanced topics in multilevel modeling, structural equation modeling, and hybrid combinations, such as moderated mediation. User-friendly features include numerous graphs and carefully worked-through examples; ""Helpful Suggestions"" about procedures and pitfalls; ""Knowled