Properties Of Viscose Vortex Yarns Depending On Technological Parameters Of Spinning

Directory of Open Access Journals (Sweden)

Moučková Eva

2015-06-01

Full Text Available This paper analyzes the relationship between technological parameters of spinning of 100% CV Vortex yarns of different counts and its selected geometrical parameters (a lead of helix of wrapping fibre ribbon, yarn diameter as well as yarn properties. The number of twist of wrapping fibre layer is determined. The effect of the yarn delivery speed, hollow spindle diameter, and the main draft on the hairiness, mass irregularity, tenacity, elongation, resistance to abrasion and bending rigidity of Vortex yarn is observed. The yarn properties are compared with the properties of open-end rotor spun yarns. Slivers of the same spinning lot were used for the production of both kinds of yarn. The results showed that the delivery speed in combination with spindle diameter affects yarn diameter, hairiness and abrasion resistance. Mass irregularity and imperfections of yarn is mainly affected by the main draft of drafting unit. Technological parameters of spinning do not affect the level of bending rigidity of the Vortex yarn. Tested rotor spun yarns had a larger diameter, higher hairiness, lower tenacity and higher elongation, lower mass irregularity and number of imperfections, higher abrasion resistance and lower bending rigidity compared to tested Vortex spun yarns.

Improvement of system capacitance via weavable superelastic biscrolled yarn supercapacitors

Science.gov (United States)

Choi, Changsoon; Kim, Kang Min; Kim, Keon Jung; Lepró, Xavier; Spinks, Geoffrey M.; Baughman, Ray H.; Kim, Seon Jeong

2016-12-01

Yarn-based supercapacitors having improved performance are needed for existing and emerging wearable applications. Here, we report weavable carbon nanotube yarn supercapacitors having high performance because of high loadings of rapidly accessible charge storage particles (above 90 wt% MnO2). The yarn electrodes are made by a biscrolling process that traps host MnO2 nanoparticles within the galleries of helically scrolled carbon nanotube sheets, which provide strength and electrical conductivity. Despite the high loading of brittle metal oxide particles, the biscrolled solid-state yarn supercapacitors are flexible and can be made elastically stretchable (up to 30% strain) by over-twisting to produce yarn coiling. The maximum areal capacitance of the yarn electrodes were up to 100 times higher than for previously reported fibres or yarn supercapacitors. Similarly, the energy density of complete, solid-state supercapacitors made from biscrolled yarn electrodes with gel electrolyte coating were significantly higher than for previously reported fibre or yarn supercapacitors.

Properties of Plant Fiber Yarn Polymer Composites

DEFF Research Database (Denmark)

Madsen, Bo

2004-01-01

. The thesis presents experimental investigations and modelling of the properties of aligned plant fibre composites based on textile hemp yarn and thermoplastic matrices. The textile hemp yarn has been characterised. It is high in cellulose and with fibres well separated from each other; i.e. only few fibres...... are situated in bundles. The twisting angle is low; i.e. about 15 o for the outermost fibres in the yarn. The moisture sorption capacity of the yarn fibres is much lower than that of raw hemp fibres. Stiffness and strength of the fibres as calculated from composite data are in the ranges 50-65 GPa and 530......-650 MPa respectively. These properties show that textile hemp yarn is well suited as composite reinforcement. The relationship between fibre volume fraction and porosity has been studied. A model has been developed that predicts porosity from experimentally determined parameters such as fibre lumen...

Flexible two-ply yarn supercapacitors based on carbon nanotube/stainless steel core spun yarns decorated with Co3O4 nanoparticles and MnOx composites

International Nuclear Information System (INIS)

Su, Fenghua; Lyu, Xiaoming; Liu, Cansen; Miao, Menghe

2016-01-01

Highlights: • Carbon nanotube/stainless steel core-sheath yarns as electrode for two-ply supercapacitor. • The yarns were decorated with Co 3 O 4 nanoparticles and MnO x composites. • Yarn electrodes deposited on Co 3 O 4 and MnO x have excellent specific capacitance. • The two-ply yarn supercapacitor based on MnO x has high energy density and power density. • The yarn supercapacitors are highly flexible and strong for wearable electronics. - Abstract: High performance two-ply yarn supercapacitors are fabricated by electrodeposition of transition metal oxide pseudocapacitive materials on carbon nanotube/stainless steel (CNT/SS) core spun yarns. The SS core incorporated in the carbon nanotube yarn has dramatically improved the conductivity of the substrate and the efficiency of electrodeposition of metal oxides on the electrodes. The SS core acts as current collector in the final two-ply yarn supercapacitors with significantly improved specific capacitance and up-scaled length of supercapacitors. Manganese oxide and cobalt oxide electrodeposited on as-spun CNT/SS yarn are compared for their electrochemical performance in two-ply yarn supercapacitors. Both supercapacitors displayed improvement in capacitance, energy and power densities, especially MnO x /CNT/SS yarn supercapacitor. The solid-state supercapacitor based on MnO x /CNT/SS composite yarn shows excellent electrochemical properties with a specific capacitance of 217.61 F/cm 3 at 0.02 V/s and an energy density of 4.84 mWh/cm 3 at a power density of 435.22 mW/cm 3 .

Fast Torsional Artificial Muscles from NiTi Twisted Yarns.

Science.gov (United States)

Mirvakili, Seyed M; Hunter, Ian W

2017-05-17

Torsional artificial muscles made of multiwalled carbon nanotube/niobium nanowire yarns have shown remarkable torsional speed and gravimetric torque. The muscle structure consists of a twisted yarn with half of its length infiltrated with a stimuli-responsive guest material such as paraffin wax. The volumetric expansion of the guest material creates the torsional actuation in the yarn. In the present work, we show that this type of actuation is not unique to wax-infiltrated carbon multiwalled nanotube (MWCNT) or niobium nanowire yarns and that twisted yarn of NiTi alloy fibers also produces fast torsional actuation. By gold-plating half the length of a NiTi twisted yarn and Joule heating it, we achieved a fully reversible torsional actuation of up to 16°/mm with peak torsional speed of 10 500 rpm and gravimetric torque of 8 N·m/kg. These results favorably compare to those of MWCNTs and niobium nanowire yarns.

Statistical Modeling for the Effect of Rotor Speed, Yarn Twist and Linear Density on Production and Quality Characteristics of Rotor Spun Yarn

Directory of Open Access Journals (Sweden)

Farooq Ahmed Arain

2012-01-01

Full Text Available The aim of this study was to develop a statistical model for the effect of RS (Rotor Speed, YT (Yarn Twist and YLD (Yarn Linear Density on production and quality characteristics of rotor spun yarn. Cotton yarns of 30, 35 and 40 tex were produced on rotor spinning machine at different rotor speeds (i.e. 70000, 80000, 90000 and 100000 rpm and with different twist levels (i.e. 450, 500, 550, 600 and 700 tpm. Yarn production (g/hr and quality characteristics were determined for all the experiments. Based on the results, models were developed using response surface regression on MINITAB�16 statistical tool. The developed models not only characterize the intricate relationships among the factors but may also be used to predict the yarn production and quality characteristics at any level of factors within the range of experimental values.

A Review of the MLAS Parachute Systems

Science.gov (United States)

Taylor, Anthony P.; Kelley, Christopher; Magner, Eldred; Peterson, David; Hahn, Jeffrey; Yuchnovicz, Daniel E.

2009-01-01

The NASA Engineering and Safety Center (NESC) is developing the Max Launch Abort System (MLAS) as a risk-mitigation design should problems arise with the baseline Orion spacecraft launch abort design. The Max in MLAS is dedicated to Max Faget, the renowned NASA spacecraft designer. The MLAS flight test vehicle consists of boost skirt, coast skirt and the MLAS fairing which houses a full scale boilerplate Orion Crew Module (CM). The objective of the flight test is to prove that the CM can be released from the MLAS fairing during pad abort conditions without detrimental recontact between the CM and fairing, achieving performance similar to the Orion launch abort system. The boost and coast skirts provide the necessary thrust and stability to achieve the flight test conditions and are released prior to the test -- much like the Little Joe booster was used in the Apollo Launch Escape System tests. To achieve the test objective, two parachutes are deployed from the fairing to reorient the CM/fairing to a heatshield first orientation. The parachutes then provide the force necessary to reduce the total angle of attack and body angular rates required for safe release of the CM from the fairing. A secondary test objective after CM release from the fairing is to investigate the removal of the CM forward bay cover (FBC) with CM drogue parachutes for the purpose of attempting to synchronously deploying a set of CM main parachutes. Although multiple parachute deployments are used in the MLAS flight test vehicle to complete its objective, there are only two parachute types employed in the flight test. Five of the nine parachutes used for MLAS are 27.6 ft D(sub 0) ribbon parachutes, and the remaining four are standard G-12 cargo parachutes. This paper presents an overview of the 27.6 ft D(sub 0) ribbon parachute system employed on the MLAS flight test vehicle for coast skirt separation, fairing reorientation, and as drogue parachutes for the CM after separation from the fairing

Load Asymmetry Observed During Orion Main Parachute Inflation

Science.gov (United States)

Morris, Aaron L.; Taylor, Thomas; Olson, Leah

2011-01-01

The Crew Exploration Vehicle Parachute Assembly System (CPAS) has flight tested the first two generations of the Orion parachute program. Three of the second generation tests instrumented the dispersion bridles of the Main parachute with a Tension Measuring System. The goal of this load measurement was to better understand load asymmetry during the inflation process of a cluster of Main parachutes. The CPAS Main parachutes exhibit inflations that are much less symmetric than current parachute literature and design guides would indicate. This paper will examine loads data gathered on three cluster tests, quantify the degree of asymmetry observed, and contrast the results with published design guides. Additionally, the measured loads data will be correlated with videos of the parachute inflation to make inferences about the shape of the parachute and the relative load asymmetry. The goal of this inquiry and test program is to open a dialogue regarding asymmetrical parachute inflation load factors.

VACUUM STEAMING PROCESSES APPLIED TO YARNS, ITS APPLICATION FIELDS AND IMPROVEMENTS

Directory of Open Access Journals (Sweden)

Özcan ÖZDEMİR

2005-02-01

Full Text Available The new techniques used today focus mainly on increases in production speed. For this reason yarns to be used in high speed machines is required to be of high quality. On the other hand high speed frequently causes the degree of yarn moisture to fall minimum level. This decreases in the degree of yarn moisture have negative effects on yarn strength. Since better moisture level increases the yarn strength, yarn is worked more efficiently in weaving and knitting. However each production step in textile plants causes tension in yarn and fibre. Yarns tend to snarl in order to relax themselves.Tension and snarling may lead to problems in the following proceses, thus decreasing productivity. Therefore, the moisture content of yarns should be increased and their tension should be eleminated. In this article we have studied vacuum steaming widely used to remedy above mentioned yarn problems, its application fields and new improvements in this field.

Application of an automatic yarn dismantler to track changes in cotton fiber properties during full scale processing of cotton into carded yarn

CSIR Research Space (South Africa)

Fassihi, A

2016-08-01

Full Text Available Changes in Upland cotton fiber properties from lint to carded yarn, during full scale processing, were tracked, using a newly developed automatic yarn dismantler for dismantling short staple ring-spun yarns. Opening and cleaning increased fiber neps...

Regressional Estimation of Cotton Sirospun Yarn Properties from Fibre Properties

Directory of Open Access Journals (Sweden)

Bedez Üte Tuba

2014-09-01

Full Text Available In this paper, it is aimed at determining the equations and models for estimating the sirospun yarn quality characteristics from the yarn production parameters and cotton fibre properties, which are focused on fibre bundle measurements represented by HVI (high volume instrument. For this purpose, a total of 270 sirospun yarn samples were produced on the same ring spinning machine under the same conditions at Ege University, by using 11 different cotton blends and three different strand spacing settings, in four different yarn counts and in three different twist coefficients. The sirospun yarn and cotton fibre property interactions were investigated by correlation analysis. For the prediction of yarn quality characteristics, multivariate linear regression methods were performed. As a result of the study, equations were generated for the prediction of yarn tenacity, breaking elongation, unevenness and hairiness by using fibre and yarn properties. After the goodness of fit statistics, very large determination coefficients (R2 and adjusted R2 were observed.

Preparation of Highly Conductive Yarns by an Optimized Impregnation Process

Science.gov (United States)

Amba Sankar, K. N.; Mohanta, Kallol

2018-03-01

We report the development of the electrical conductivity in textile yarns through impregnation and post-treatment of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). The conductive polymer is deposited on fibers, which fills the gap space within the hierarchical structure of the yarns. Organic nonpolar solvents act as reducing agent to increase the density of PEDOT moieties on the yarns, galvanizing increment in conductivity values. Post-treatment by ethylene glycol transforms the resonance configuration of the conductive moieties of conjugated polymer, which helps in further enhancement of electrical conductivity of the yarns. We have optimized the method in terms of loading and conformal change of the polymer to have a lesser resistance of the coated conductive yarns. The minimum resistance achieved has a value of 77 Ωcm-1. This technique of developing conductivity in conventional yarns enables retaining the flexibility of yarns and feeling of softness which would find suitable␣applications for wearable electronics.

Computational fluid dynamics modeling in yarn engineering

CSIR Research Space (South Africa)

Patanaik, A

2011-07-01

Full Text Available pattern in the nozzles plays a significant role in the reduction of hairiness. CFD has been effectively utilized in yarn engineering to understand the actual mechanism of reducing yarn hairiness. The influence of different nozzle parameters...

Application of image processing technology in yarn hairiness detection

Directory of Open Access Journals (Sweden)

Guohong ZHANG

2016-02-01

Full Text Available Digital image processing technology is one of the new methods for yarn detection, which can realize the digital characterization and objective evaluation of yarn appearance. This paper overviews the current status of development and application of digital image processing technology used for yarn hairiness evaluation, and analyzes and compares the traditional detection methods and this new developed method. Compared with the traditional methods, the image processing technology based method is more objective, fast and accurate, which is the vital development trend of the yarn appearance evaluation.

Design and Fabrication of Smart Diapers with Antibacterial Yarn

Directory of Open Access Journals (Sweden)

Jia-Horng Lin

2017-01-01

Full Text Available In this study, intelligent eco-diapers are made by combining antibacterial yarns coated with quaternary ammonium salts with conductive yarns to improve caretaking for urinary incontinence. The combination of conductive yarns and sensors can detect the moisture content in eco-diapers, and an alarm is sent when moisture is significant. A wireless module is used to send detected signals to a smartphone or tablet PC via the Internet. This concept is used for a scenario in which nurses do not randomly check on patients in a long-term care institution. When used offline, eco-diapers can send caregivers an alarm for the need to change diapers via cell phones. The diameters of the copper and silver-plated copper fibers are 0.08 and 0.10 mm, respectively. Cotton yarns are twisted with copper and silver-plated copper fibers to form the conductive yarns, which are 0.12 mm in diameter. Moreover, 30-count cotton and 150 D nylon yarns are coated with quaternary ammonium salt via dyeing and finishing processes to form antibacterial yarns. In the current study, intelligent eco-diapers are tested for their electrical and antibacterial properties as specified by AATC and JISL test standards.

Optimum Drafting Conditions Of Polyester And Viscose Blend Yarns

Directory of Open Access Journals (Sweden)

Hatamvand Mohammad

2017-09-01

Full Text Available In this study, we used an experimental design to investigate the influence of the total draft, break draft, distance between the aprons (Clips and production roller pressure on yarn quality in order to obtain optimum drafting conditions for polyester and viscose (PES/CV blend yarns in ring spinning frame. We used PES fibers (1.4 dtex × 38 mm long and CV fibers (1.6 dtex × 38 mm long to spin a 20 Tex blend yarn of PES (70%/CV (30% blend ratio. When the break draft, adjustment of distance between of aprons and roller pressure is not reasonable, controlling and leading of the fibers is not sufficient for proper orientation of the fibers in the yarn structure to produce a high quality yarn. Experimental results and statistical analysis show that the best yarn quality will be obtained under drafting conditions total draft of 38, 1.2 break draft, 2.8 mm distance between of aprons and maximum pressure of the production top roller (18daN.

Single-Wall Carbon Nanotube-Coated Cotton Yarn for Electrocardiography Transmission

Directory of Open Access Journals (Sweden)

Yuliang Zhao

2018-03-01

Full Text Available We fabricated a type of conductive fabric, specifically single-wall carbon nanotube-coated cotton yarns (SWNT-CYs, for electrocardiography (ECG signal transmission utilizing a “dipping and drying” method. The conductive cotton yarns were prepared by dipping cotton yarns in SWNTs (single-wall carbon nanotubes solutions and then drying them at room temperature—a simple process that shows consistency in successfully coating cotton yarns with conductive carbon nanotubes (CNTs. The influence of fabrication conditions on the conductivity properties of SWNT-CYs was investigated. The results demonstrate that our conductive yarns can transmit weak bio-electrical (i.e., ECG signals without significant attenuation and distortion. Our conductive cotton yarns, which combine the flexibility of conventional fabrics and the good conductivity of SWNTs, are promising materials for wearable electronics and sensor applications in the future.

ANALYSIS OF RIBBONING ON CONICAL YARN PACKAGE WOUND BY OPENEND SPINNING MACHINES

Directory of Open Access Journals (Sweden)

Resul FETTAHOV

2001-03-01

Full Text Available In this paper, Ribboning , one of the common faults in yarn packages, is mathematically analysed. If yarn is repeatly laid on top of or along the same path as the previously wound yarn, this duplication of yarn path on the package creates a defect known as ribboning. The number of turns of package (n per double traverse of yarn guide is calculated in two different way One is calculated the length of a coil on the package and total length of yarn in a double traverse; the other is considered transmission rate between drum and conical yarn package The result of two different approach is similar and the probable diameter of conical yarn package which ribboning is occurred is calculated and used on Schalafhorst-Autocore OE spinning machines.

Weavable dye sensitized solar cells exploiting carbon nanotube yarns

Science.gov (United States)

Velten, Josef; Kuanyshbekova, Zharkynay; Göktepe, Özer; Göktepe, Fatma; Zakhidov, Anvar

2013-05-01

Weavable Dye Sensitized Solar Cells (DSSC) made with flexible yarns of conductive multiwalled carbon nanotubes (MWNTs) were produced having a power conversion efficiency above 3%. This was achieved with a specific design and careful consideration of the yarn function in the DSSC. Fermat yarns of MWNTs individually coated with mesoporous TiO2 layer were twisted together and coated with more mesoporous TiO2 to create a 3 dimensional photo electrode to overcome electron diffusion length issues. Archimedian yarns of MWNTs coated with a thin layer of platinum worked as a counter electrode to complete the architecture used in this DSSC.

Yarn Pull-Out as a Mechanism for Dissipation of Ballistic Impact Energy in Kevlar KM-2 Fabric, Part 1: Quasi-Static Characterization of Yarn Pull-Out

National Research Council Canada - National Science Library

Kirkwood, Keith

2004-01-01

.... This study reports the effects of fabric length, number of yarns pulled, arrangement of yarns, and transverse tension on the force-displacement curves for yarn pull-out tests on Kevlar KM-2 fabric...

Functionalization of carbon nanotube yarn by acid treatment

Directory of Open Access Journals (Sweden)

H.E. Misak

2014-01-01

Full Text Available Carbon nanotube (CNT yarn was functionalized using sulfuric and nitric acid solutions in 3:1 volumetric ratio. Successful functionalization of CNT yarn with carboxyl and hydroxyl groups (e.g., COOH, COO–, OH, etc. was confirmed by attenuated total reflectance spectroscopy. X-ray diffraction revealed no significant change to the atomic in-plane alignment in the CNTs; however, the coherent length along the diameter was significantly reduced during functionalization. A morphology change of wavy extensions protruding from the surface was observed after the functionalization treatment. The force required to fracture the yarn remained the same after the functionalization process; however, the linear density was increased (310%. The increase in linear density after functionalization reduced the tenacity. However, the resistivity density product of the CNT yarn was reduced significantly (234% after functionalization.

Biscrolling nanotube sheets and functional guests into yarns.

Science.gov (United States)

Lima, Márcio D; Fang, Shaoli; Lepró, Xavier; Lewis, Chihye; Ovalle-Robles, Raquel; Carretero-González, Javier; Castillo-Martínez, Elizabeth; Kozlov, Mikhail E; Oh, Jiyoung; Rawat, Neema; Haines, Carter S; Haque, Mohammad H; Aare, Vaishnavi; Stoughton, Stephanie; Zakhidov, Anvar A; Baughman, Ray H

2011-01-07

Multifunctional applications of textiles have been limited by the inability to spin important materials into yarns. Generically applicable methods are demonstrated for producing weavable yarns comprising up to 95 weight percent of otherwise unspinnable particulate or nanofiber powders that remain highly functional. Scrolled 50-nanometer-thick carbon nanotube sheets confine these powders in the galleries of irregular scroll sacks whose observed complex structures are related to twist-dependent extension of Archimedean spirals, Fermat spirals, or spiral pairs into scrolls. The strength and electronic connectivity of a small weight fraction of scrolled carbon nanotube sheet enables yarn weaving, sewing, knotting, braiding, and charge collection. This technology is used to make yarns of superconductors, lithium-ion battery materials, graphene ribbons, catalytic nanofibers for fuel cells, and titanium dioxide for photocatalysis.

On the Mechanical Properties and Uncertainties of Jute Yarns

Directory of Open Access Journals (Sweden)

AMM Sharif Ullah

2017-04-01

Full Text Available Products made from natural materials are eco-friendly. Therefore, it is important to supply product developers with reliable information regarding the properties of natural materials. In this study, we consider a widely used natural material called jute, which grows in Bangladesh, India, and China. We described the results of tensile tests on jute yarns, as well as the energy absorption patterns leading to yarn failure. We have also used statistical analyses and possibility distributions to quantify the uncertainty associated with the following properties of jute yarn: tensile strength, modulus of elasticity, and strain to failure. The uncertainty and energy absorption patterns of jute yarns were compared with those of jute fibers. We concluded that in order to ensure the reliability and durability of a product made from jute, it is good practice to examine the material properties of yarns rather than those of fibers.

Effect of hand paddles and parachute on butterfly coordination.

Science.gov (United States)

Telles, Thiago; Barroso, Renato; Barbosa, Augusto Carvalho; Salgueiro, Diego Fortes de Souza; Colantonio, Emilson; Andries Júnior, Orival

2015-01-01

This study investigated the effects of hand paddles, parachute and hand paddles plus parachute on the inter-limb coordination of butterfly swimming. Thirteen male swimmers were evaluated in four random maximal intensity conditions: without equipment, with hand paddles, with parachute and with hand paddles + parachute. Arm and leg stroke phases were identified by 2D video analysis to calculate the total time gap (T1: time between hands' entry in the water and high break-even point of the first undulation; T2: time between the beginning of the hand's backward movement and low break-even point of the first undulation; T3: time between the hand's arrival in a vertical plane to the shoulders and high break-even point of the second undulation; T4: time between the hand's release from the water and low break-even point of the second undulation). The swimming velocity was reduced and T1, T2 and T3 increased in parachute and hand paddles + parachute. No changes were observed in T4. Total time gap decreased in parachute and hand paddles + parachute. It is concluded that hand paddles do not influence the arm-to-leg coordination in butterfly, while parachute and hand paddles + parachute do change it, providing a greater propulsive continuity.

A continuous measurement system for yarn structures by an optical method

International Nuclear Information System (INIS)

Guo, Y; Tao, X M; Xu, B G; Choi, K F; Hua, T; Wang, S Y

2010-01-01

This paper presents a continuous observation and measurement system to acquire spatial distributions of multiple yarn structural parameters and a three-dimensional configuration of fibres in yarns. The system comprises an automatic yarn transmission unit, an optical observation device, image acquisition, analysis and display units. Spatial orientation of fibre, distribution of yarn twist and diameters, fibre radial position and other migration characteristics are, for the first time, determined in a simultaneous fashion. Extensive experiments were carried out to evaluate the system. In addition to the studies on different yarn types, further investigations were made on two types of yarns including the twist in short yarn segments, fibre orientation angle, radial position, migration frequency and amplitude as well the three-dimensional configurations of fibres. The experimental results indicate that the present system has good reliability and repeatability. The measured values are in good agreement with those obtained by other conventional techniques for single-parameter measurements

Antifungal activity of fabrics knitted by metalized Silver/Polyester composite yarn

Science.gov (United States)

Özkan, İ.; Duru Baykal, P.

2017-10-01

In this study, antifungal properties of fabric knitted from metalized silver/polyester composite yarn were investigated. Intermingling is an alternative technique for yarn blending process. Yarns having different features can be combined by feeding the same intermingling jet. This process is defined as commingling. In the study, intermingling process was used to produce metalized silver/polyester composite yarn. Commingled yarns were knitted to single jersey fabrics by IPM brand sample type circular knitting machine. Antifungal activity test was applied to samples against Aspergillus Niger according to AATCC 30 test procedure. It has been identified that the application provides antifungal activity to fabric.

Artificial neural nets application in the cotton yarn industry

Directory of Open Access Journals (Sweden)

Gilberto Clóvis Antoneli

2016-06-01

Full Text Available The competitiveness in the yarn production sector has led companies to search for solutions to attain quality yarn at a low cost. Today, the difference between them, and thus the sector, is in the raw material, meaning processed cotton and its characteristics. There are many types of cotton with different characteristics due to its production region, harvest, storage and transportation. Yarn industries work with cotton mixtures, which makes it difficult to determine the quality of the yarn produced from the characteristics of the processed fibers. This study uses data from a conventional spinning, from a raw material made of 100% cotton, and presents a solution with artificial neural nets that determine the thread quality information, using the fibers’ characteristics values and settings of some process adjustments. In this solution a neural net of the type MultiLayer Perceptron with 11 entry neurons (8 characteristics of the fiber and 3 process adjustments, 7 output neurons (yarn quality and two types of training, Back propagation and Conjugate gradient descent. The selection and organization of the production data of the yarn industry of the cocamar® indústria de fios company are described, to apply the artificial neural nets developed. In the application of neural nets to determine yarn quality, one concludes that, although the ideal precision of absolute values is lacking, the presented solution represents an excellent tool to define yarn quality variations when modifying the raw material composition. The developed system enables a simulation to define the raw material percentage mixture to be processed in the plant using the information from the stocked cotton packs, thus obtaining a mixture that maintains the stability of the entire productive process.

Basic Comparison of the Properties of the Loop and Frotte Yarns, Woven and Knitted Fabrics

Directory of Open Access Journals (Sweden)

Ewa Grabowska Katarzyna

2014-09-01

Full Text Available Both loop fancy yarns and frotte fancy yarns belong to the group of yarns with continuous effects. The difference between frotte and loop yarn relies on the fact that the loop yarn is constructed with two core yarns and the frotte yarn is constructed with only one core yarn. The differences are evident in the shape of these two types of fancy yarns. These shape differences are the functions of the tensions of component yarns during the twisting process. The shape and construction of the fancy yarn influence its properties. The properties of loop and frotte fancy yarns, woven and knitted fabrics are compared in this article in order to find out the optimal yarn’s and fabric’s production condition to satisfy the final user and maintain low production costs. In terms of economy aspects only, the frotte fancy yarns are believed to be cheaper in production due to lower quantity of components utilize for their production to compare with loop fancy yarns, under conditions of the same settings of ring twisting frame.

Solid Rocket Booster Large Main and Drogue Parachute Reliability Analysis

Science.gov (United States)

Clifford, Courtenay B.; Hengel, John E.

2009-01-01

The parachutes on the Space Transportation System (STS) Solid Rocket Booster (SRB) are the means for decelerating the SRB and allowing it to impact the water at a nominal vertical velocity of 75 feet per second. Each SRB has one pilot, one drogue, and three main parachutes. About four minutes after SRB separation, the SRB nose cap is jettisoned, deploying the pilot parachute. The pilot chute then deploys the drogue parachute. The drogue chute provides initial deceleration and proper SRB orientation prior to frustum separation. At frustum separation, the drogue pulls the frustum from the SRB and allows the main parachutes that are mounted in the frustum to unpack and inflate. These chutes are retrieved, inspected, cleaned, repaired as needed, and returned to the flight inventory and reused. Over the course of the Shuttle Program, several improvements have been introduced to the SRB main parachutes. A major change was the replacement of the small (115 ft. diameter) main parachutes with the larger (136 ft. diameter) main parachutes. Other modifications were made to the main parachutes, main parachute support structure, and SRB frustum to eliminate failure mechanisms, improve damage tolerance, and improve deployment and inflation characteristics. This reliability analysis is limited to the examination of the SRB Large Main Parachute (LMP) and drogue parachute failure history to assess the reliability of these chutes. From the inventory analysis, 68 Large Main Parachutes were used in 651 deployments, and 7 chute failures occurred in the 651 deployments. Logistic regression was used to analyze the LMP failure history, and it showed that reliability growth has occurred over the period of use resulting in a current chute reliability of R = .9983. This result was then used to determine the reliability of the 3 LMPs on the SRB, when all must function. There are 29 drogue parachutes that were used in 244 deployments, and no in-flight failures have occurred. Since there are no

Potentiometric sensors using cotton yarns, carbon nanotubes and polymeric membranes.

Science.gov (United States)

Guinovart, Tomàs; Parrilla, Marc; Crespo, Gastón A; Rius, F Xavier; Andrade, Francisco J

2013-09-21

A simple and generalized approach to build electrochemical sensors for wearable devices is presented. Commercial cotton yarns are first turned into electrical conductors through a simple dyeing process using a carbon nanotube ink. These conductive yarns are then partially coated with a suitable polymeric membrane to build ion-selective electrodes. Potentiometric measurements using these yarn-potentiometric sensors are demonstrated. Examples of yarns that can sense pH, K(+) and NH4(+) are presented. In all cases, these sensing yarns show limits of detection and linear ranges that are similar to those obtained with lab-made solid-state ion-selective electrodes. Through the immobilization of these sensors in a band-aid, it is shown that this approach could be easily implemented in a wearable device. Factors affecting the performance of the sensors and future potential applications are discussed.

Thread-like supercapacitors based on one-step spun nanocomposite yarns.

Science.gov (United States)

Meng, Qinghai; Wang, Kai; Guo, Wei; Fang, Jin; Wei, Zhixiang; She, Xilin

2014-08-13

Thread-like electronic devices have attracted great interest because of their potential applications in wearable electronics. To produce high-performance, thread-like supercapacitors, a mixture of stable dispersions of single-walled carbon nanotubes and conducting polyaniline nanowires are prepared. Then, the mixture is spun into flexible yarns with a polyvinyl alcohol outer sheath by a one-step spinning process. The composite yarns show excellent mechanical properties and high electrical conductivities after sufficient washing to remove surfactants. After applying a further coating layer of gel electrolyte, two flexible yarns are twisted together to form a thread-like supercapacitor. The supercapacitor based on these two yarns (SWCNTs and PAniNWs) possesses a much higher specific capacitance than that based only on pure SWCNTs yarns, making it an ideal energy-storage device for wearable electronics. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Study on Single-yarn Pullout Test of Ballistic Resistant Fabric under Different Preloads

Science.gov (United States)

Fang, Q. C.; Lei, Z. K.; Y Qin, F.; Li, W. K.; Bai, R. X.

2017-12-01

During bullet penetrating fabric, the pull-out force of yarn in fabric is related to the impact resistance of fabric when the yarn is pulled out from the fabric. The complex uncrimping and friction slip behavior occur during the yarn pullout process, which is critical to learn the impact resistance of fabric. Based on digital image correlation technique, the deformation behavior of Kevlar 49 fabric subjected to preload during the single-yarn pullout process was studied in this paper. The pullout force and displacement curve shows a straight rise and an oscillated decrease. In the linear rise stage, the yarn uncrimping causes a static friction effect. The maximum of the pullout force is not linearly increased with the preload. In the oscillating descending stage, the local descent of the pullout force indicates that the yarn end is gradually withdrawn from the fabric, and the local rise indicates that the yarn end moves to the next weft/warp interaction until the yarn is completely pulled out. The shear deformation of fabric corresponds to the single-yarn pullout process.

Parachute systems for the atmospheric reentry of launcher upper stages

Directory of Open Access Journals (Sweden)

Bogdan DOBRESCU

2017-03-01

Full Text Available Parachute systems can be used to control the reentry trajectory of launcher upper stages, in order to lower the risks to the population or facilitate the retrieval of the stage. Several types of parachutes deployed at subsonic, supersonic and hypersonic speeds are analyzed, modeled as single and multistage systems. The performance of deceleration parachutes depends on their drag area and deployment conditions, while gliding parachutes are configured to achieve stable flight with a high glide ratio. Gliding parachutes can be autonomously guided to a low risk landing area. Sizing the canopy is shown to be an effective method to reduce parachute sensitivity to wind. The reentry trajectory of a launcher upper stage is simulated for each parachute system configuration and the results are compared to the nominal reentry case.

FEAR AND ENTHUSIASM IN SPORT PARACHUTING,

Science.gov (United States)

Replies to a mail questionnaire by 825 sport parachutists affiliated with 103 parachute clubs are the data of this study. Questionnaires were...parachutists, attitudes relevant to sport parachuting, and included the Ma and Hy scales from the MMP1, a Draw-A-Person Test, and four story stimulus pictures

Development of yarn breakage detection software system based on machine vision

Science.gov (United States)

Wang, Wenyuan; Zhou, Ping; Lin, Xiangyu

2017-10-01

For questions spinning mills and yarn breakage cannot be detected in a timely manner, and save the cost of textile enterprises. This paper presents a software system based on computer vision for real-time detection of yarn breakage. The system and Windows8.1 system Tablet PC, cloud server to complete the yarn breakage detection and management. Running on the Tablet PC software system is designed to collect yarn and location information for analysis and processing. And will be processed after the information through the Wi-Fi and http protocol sent to the cloud server to store in the Microsoft SQL2008 database. In order to follow up on the yarn break information query and management. Finally sent to the local display on time display, and remind the operator to deal with broken yarn. The experimental results show that the system of missed test rate not more than 5%o, and no error detection.

Asymmetric carbon nanotube-MnO2 two-ply yarn supercapacitors for wearable electronics

Science.gov (United States)

Su, Fenghua; Miao, Menghe

2014-04-01

Strong and flexible two-ply carbon nanotube yarn supercapacitors are electrical double layer capacitors that possess relatively low energy storage capacity. Pseudocapacitance metal oxides such as MnO2 are well known for their high electrochemical performance and can be coated on carbon nanotube yarns to significantly improve the performance of two-ply carbon nanotube yarn supercapacitors. We produced a high performance asymmetric two-ply yarn supercapacitor from as-spun CNT yarn and CNT@MnO2 composite yarn in aqueous electrolyte. The as-spun CNT yarn serves as negative electrode and the CNT@MnO2 composite yarn as positive electrode. This asymmetric architecture allows the operating potential window to be extended from 1.0 to 2.0 V and results in much higher energy and power densities than the reference symmetric two-ply yarn supercapacitors, reaching 42.0 Wh kg-1 at a lower power density of 483.7 W kg-1, and 28.02 Wh kg-1 at a higher power density of 19 250 W kg-1. The asymmetric supercapacitor can sustain cyclic charge-discharge and repeated folding/unfolding actions without suffering significant deterioration of specific capacitance. The combination of high strength, flexibility and electrochemical performance makes the asymmetric two-ply yarn supercapacitor a suitable power source for flexible electronic devices for applications that require high durability and wearer comfort.

Effect of conducting polypyrrole on the transport properties of carbon nanotube yarn

International Nuclear Information System (INIS)

Foroughi, Javad; Kimiaghalam, Bahram; Ghorbani, Shaban Reza; Safaei, Farzad; Abolhasan, Mehran

2012-01-01

Experiments were conducted to measure the electrical conductivity in three types of pristine and carbon nanotube-polypyrrole (CNT-PPy) composite yarns and its dependence on over a wide temperature range. The experimental results fit well with the analytical models developed. The effective energy separation between localized states of the pristine CNT yarn is larger than that for both the electrochemically and chemically prepared CNT-PPy yarns. It was found that all samples are in the critical regime in the insulator–metal transition, or close to the metallic regime at low temperature. The electrical conductivity results are in good agreement with a Three Dimensional Variable Range Hopping model at low temperatures, which provides a strong indication that electron hopping is the main means of current transfer in CNT yarns at T < 100 K. We found that the two shell model accurately describes the electronic properties of CNT and CNT-PPy composite yarns in the temperature range of 5–350 K. - Highlights: ► We developed hybrid carbon nanotube conducting polypyrrole composite yarns. ► The main current transfer scheme in yarn is via three dimensional electrons hopping. ► Two shell model describes well electronic properties of yarns in range of 5-350 K.

Flexible helical yarn swimmers.

Science.gov (United States)

Zakharov, A P; Leshansky, A M; Pismen, L M

2016-09-01

We investigate the motion of a flexible Stokesian flagellar swimmer realised as a yarn made of two intertwined elastomer fibres, one active, that can reversibly change its length in response to a local excitation causing transition to the nematic state or swelling, and the other one, a passive isotropic elastomer with identical mechanical properties. A propagating chemical wave may provide an excitation mechanism ensuring a constant length of the excited region. Generally, the swimmer moves along a helical trajectory, and the propagation and rotation velocity are very sensitive to the ratio of the excited region to the pitch of the yarn, as well as to the size of a carried load. External excitation by a moving actuating beam is less effective, unless the direction of the beam is adjusted to rotation of the swimmer.

Metallic conductivity transition of carbon nanotube yarns coated with silver particles

International Nuclear Information System (INIS)

Zhang, Daohong; Zhang, Yunhe; Miao, Menghe

2014-01-01

Dry spun carbon nanotube yarns made from vertically aligned multiwalled carbon nanotube forests possess high mechanical strength and behave like semiconductors with electrical conductivity of the order of 4 × 10 4 S m −1 . Coating a submicron-thick film of silver particle-filled polymer on the surface increased the electrical conductivity of the carbon nanotube yarn by 60-fold without significantly sacrificing its mechanical strength. The transitional characteristics of the silver-coated carbon nanotube yarn were investigated by varying the take-up ratio of the silver coating. A step change in conductivity was observed when the silver content in the coated yarn was between 7 and 10 wt% as a result of the formation of connected silver particle networks on the carbon nanotube yarn surface. (papers)

Fluid-Structure Interaction Analysis of Parachute Finite Mass Inflation

Directory of Open Access Journals (Sweden)

Xinglong Gao

2016-01-01

Full Text Available Parachute inflation is coupled with sophisticated fluid-structure interaction (FSI and flight mechanic behaviors in a finite mass situation. During opening, the canopy often experiences the largest deformation and loading. To predict the opening phase of a parachute, a computational FSI model for the inflation of a parachute, with slots on its canopy fabric, is developed using the arbitrary Lagrangian-Euler coupling penalty method. In a finite mass situation, the fluid around the parachute typically has an unsteady flow; therefore, a more complex opening phase and FSI dynamics of a parachute are investigated. Navier-Stokes (N-S equations for uncompressible flow are solved using an explicit central difference method. The three-dimensional visualization of canopy deformation as well as the evolution of dropping velocity and overload is obtained and compared with the experimental results. This technique could be further applied in the airdrop test of a parachute for true prediction of the inflation characteristics.

Asymmetric carbon nanotube–MnO2 two-ply yarn supercapacitors for wearable electronics

International Nuclear Information System (INIS)

Su, Fenghua; Miao, Menghe

2014-01-01

Strong and flexible two-ply carbon nanotube yarn supercapacitors are electrical double layer capacitors that possess relatively low energy storage capacity. Pseudocapacitance metal oxides such as MnO 2 are well known for their high electrochemical performance and can be coated on carbon nanotube yarns to significantly improve the performance of two-ply carbon nanotube yarn supercapacitors. We produced a high performance asymmetric two-ply yarn supercapacitor from as-spun CNT yarn and CNT@MnO 2 composite yarn in aqueous electrolyte. The as-spun CNT yarn serves as negative electrode and the CNT@MnO 2 composite yarn as positive electrode. This asymmetric architecture allows the operating potential window to be extended from 1.0 to 2.0 V and results in much higher energy and power densities than the reference symmetric two-ply yarn supercapacitors, reaching 42.0 Wh kg −1 at a lower power density of 483.7 W kg −1 , and 28.02 Wh kg −1 at a higher power density of 19 250 W kg −1 . The asymmetric supercapacitor can sustain cyclic charge–discharge and repeated folding/unfolding actions without suffering significant deterioration of specific capacitance. The combination of high strength, flexibility and electrochemical performance makes the asymmetric two-ply yarn supercapacitor a suitable power source for flexible electronic devices for applications that require high durability and wearer comfort. (paper)

Improvement of system capacitance via weavable superelastic biscrolled yarn supercapacitors

OpenAIRE

Choi, Changsoon; Kim, Kang Min; Kim, Keon Jung; Lepr?, Xavier; Spinks, Geoffrey M.; Baughman, Ray H.; Kim, Seon Jeong

2016-01-01

Yarn-based supercapacitors having improved performance are needed for existing and emerging wearable applications. Here, we report weavable carbon nanotube yarn supercapacitors having high performance because of high loadings of rapidly accessible charge storage particles (above 90?wt% MnO2). The yarn electrodes are made by a biscrolling process that traps host MnO2 nanoparticles within the galleries of helically scrolled carbon nanotube sheets, which provide strength and electrical conductiv...

Fatigue behaviour of core-spun yarns containing filament by means of cyclic dynamic loading

Science.gov (United States)

Esin, S.; Osman, B.

2017-10-01

The behaviour of yarns under dynamic loading is important that leads to understand the growth characteristics which is exposed to repetitive loadings during usage of fabric made from these yarns. Fabric growth is undesirable property that originated from low resilience characteristics of fabric. In this study, the effects of the filament fineness and yarn linear density on fatigue behaviour of rigid-core spun yarns were determined. Cotton covered yarns containing different filament fineness of polyester (PET) draw textured yarns (DTY) (100d/36f, 100d/96f, 100d/144f, 100d/192f and 100d/333f) and yarn linear densities (37 tex, 30 tex, 25 tex and 21 tex) were manufactured by using a modified ring spinning system at the same spinning parameters. Repetitive loads were applied for 25 cycles at levels between 0.1 and 3 N. Dynamic modulus and dynamic strain of yarn samples were analyzed statistically. Results showed that filament fineness and yarn linear density have significance effect on dynamic modulus and dynamic strain after cyclic loading.

Biscrolling nanotube sheets and functional guests into yarns

Science.gov (United States)

Baughman, Ray

2011-03-01

Multifunctional applications of textiles have been limited by the inability to spin important materials into yarns. Generically applicable methods are demonstrated for producing weavable yarns comprising up to 95 wt % of otherwise unspinnable particulate or nanofiber powders that remain highly functional. Scrolled 50 nm thick carbon nanotube sheets confine these powders in the galleries of irregular scroll sacks, whose observed complex structures are related to twist-dependent extension of Archimedean spirals, Fermat spirals, or spiral pairs into scrolls. The strength and electronic connectivity of a small weight fraction of scrolled carbon nanotube sheet enables yarn weaving, sewing, knotting, braiding, and charge collection. This technology is used to make yarns of superconductors, Li-ion battery materials, graphene ribbons, catalytic nanofibers for fuel cells, and Ti O2 for photocatalysis. Work done in collaboration with Shaoli Fang, Xavier Lepro-Chavez, Chihye Lewis, Raquel Ovalle-Robles, Javier Carratero-Gonzalez, Elisabet Castillo-Martinez, Mikhail Kozlov, Jiyoung Oh, Neema Rawat, Carter Haines, Mohammed Haque, Vaishnavi Aare, Stephanie Stoughton, Anvar Zakhidov, and Ray Baughman, The University of Texas at Dallas / Alan G. MacDiarmid NanoTech Institute.

Characterization of Multifunctional Carbon Nanotube Yarns: In-situ Strain Sensing and Composite Reinforcement

Science.gov (United States)

Page, Christian David

A large body of scientific research and development worldwide has focused on the unprecedented structural/functional properties of carbon nanotubes (CNT), yet translation of these unique properties of CNTs to macroscopic materials has been slow to develop. CNT yarns are an appealing application for CNTs; their lightweight and small diameter can allow for them to be embedded into composite materials. Since the individual nanotubes have shown to have incredibly high strength, stiffness, and strain sensitivity, CNT yarns have the potential to be highly effective for in-situ structural health monitoring of advanced materials and structures. This work identifies the sources for losses in strength and electromechanical sensitivity. This is done by first understanding the physics involved with a CNT yarn under axial strain. Since this material is not a Newtonian solid, the stress-strain relationships are dissimilar to conventional materials, exhibiting a three zone behavior. This is present in both the stress-strain and resistance-strain relationships. A tensile test performed in-situ within a scanning electron microscope showed that the diameter of the yarn reduced greatly during tension, which indicates that the volume is not constant; therefore, the intratube/intrabundle load transfer efficiency and electrical conductivity change significantly under strain. Observation of this phenomenon helps elucidate the source for loss in the translation from nanoscopic CNTs to the macroscopic CNT yarns. Following the observation that the CNT yarn is not a solid body mechanics system, investigation into the long-standing field of textile engineering helped to identify that the CNT yarn structural hierarchy should be re-evaluated. Literary review reveals that the predominant base morphology of CNT yarns is bundles of CNTs as opposed to individual CNTs. Furthermore, in conventional textiles, it is well known that the base morphology (in textiles this is the "fiber") will bundle

Prediction of the yarn trajectories on complex braided preforms

NARCIS (Netherlands)

Kessels, J.F.A.; Kessels, J.F.A.; Akkerman, Remko

2002-01-01

Braiding can be used to manufacture preforms for resin transfer moulding (RTM). With braiding, many yarns are used, non-geodesic yarn paths are possible, and the interlaced structure of braids provides typical mechanical properties such as high impact strength. Previously, several models were

Regenerative braking systems with torsional springs made of carbon nanotube yarn

International Nuclear Information System (INIS)

Liu, S; Martin, C; Livermore, C; Lashmore, D; Schauer, M

2014-01-01

The demonstration of large stroke, high energy density and high power density torsional springs based on carbon nanotube (CNT) yarns is reported, as well as their application as an energy-storing actuator for regenerative braking systems. Originally untwisted CNT yarn is cyclically loaded and unloaded in torsion, with the maximum rotation angle increasing until failure. The maximum extractable energy density is measured to be as high as 6.13 kJ/kg. The tests also reveal structural reorganization and hysteresis in the torsional loading curves. A regenerative braking system is built to capture the kinetic energy of a wheel and store it as elastic energy in twisted CNT yarns. When the yam's twist is released, the stored energy reaccelerates the wheel. The measured energy and mean power densities of the CNT yarns in the simple regenerative braking system are up to 4.69 kJ/kg and 1.21 kW/kg, respectively. A slightly lower energy density of up to 1.23 kJ/kg and a 0.29 kW/kg mean power density are measured for the CNT yarns in a more complex system that mimics a unidirectional rotating regenerative braking mechanism. The lower energy densities for CNT yarns in the regenerative braking systems as compared with the yarns themselves reflect the frictional losses of the regenerative systems

Regenerative braking systems with torsional springs made of carbon nanotube yarn

Science.gov (United States)

Liu, S.; Martin, C.; Lashmore, D.; Schauer, M.; Livermore, C.

2014-11-01

The demonstration of large stroke, high energy density and high power density torsional springs based on carbon nanotube (CNT) yarns is reported, as well as their application as an energy-storing actuator for regenerative braking systems. Originally untwisted CNT yarn is cyclically loaded and unloaded in torsion, with the maximum rotation angle increasing until failure. The maximum extractable energy density is measured to be as high as 6.13 kJ/kg. The tests also reveal structural reorganization and hysteresis in the torsional loading curves. A regenerative braking system is built to capture the kinetic energy of a wheel and store it as elastic energy in twisted CNT yarns. When the yam's twist is released, the stored energy reaccelerates the wheel. The measured energy and mean power densities of the CNT yarns in the simple regenerative braking system are up to 4.69 kJ/kg and 1.21 kW/kg, respectively. A slightly lower energy density of up to 1.23 kJ/kg and a 0.29 kW/kg mean power density are measured for the CNT yarns in a more complex system that mimics a unidirectional rotating regenerative braking mechanism. The lower energy densities for CNT yarns in the regenerative braking systems as compared with the yarns themselves reflect the frictional losses of the regenerative systems.

Effect of Lowering Twist Levels on Quality Parameters of Rotor Spun Cotton Yarn

Directory of Open Access Journals (Sweden)

FAROOQ AHMED

2016-07-01

Full Text Available Investigations were made to explore the influence of lowering twist level on quality characteristics of rotor spun yarn. Three levels of yarn linear density (i.e. 40, 35 and 30 tex and five levels of twist (i.e. 700, 600, 550, 500, and 450 were employed during yarn spinning trials. Each twist multiple was investigated at all linear densities for tensile strength, elongation, total CVm (Coefficient of Mass Variation imperfection index and hairiness. 100% cotton yarn samples were prepared on Reiter R-40 at rotor speed of 90,000 rpm. Determination of elongation, yarn strength, hairiness, mass variation, and total imperfections index was carried out on Uster Tensorapid-4 and Uster Tester-4 as per set standards of ISO standard test methods. Based on investigations it is established that yarn strength and elongation declined minutely (Insignificant with lowering twist levels but still can be confidently used for knitting yarns. However, significant improvement in total imperfection index and marginal enhancement in CVm were experienced.

Application of Stereo PIV on a Supersonic Parachute Model

Science.gov (United States)

Wernet, Mark P.; Locke, Randy J.; Wroblewski, Adam; Sengupta, Anita

2009-01-01

The Mars Science Laboratory (MSL) is the next step in NASA's Mars Exploration Program, currently scheduled for 2011. The spacecraft's descent into the Martian atmosphere will be slowed from Mach 2 to subsonic speeds via a large parachute system with final landing under propulsive control. A Disk-Band-Gap (DBG) parachute will be used on MSL similar to the designs that have been used on previous missions, however; the DBG parachute used by MSL will be larger (21.5 m) than in any of the previous missions due to the weight of the payload and landing site requirements. The MSL parachute will also deploy at higher Mach number (M 2) than previous parachutes, which can lead to instabilities in canopy performance. Both the increased size of the DBG above previous demonstrated configurations and deployment at higher Mach numbers add uncertainty to the deployment, structural integrity and performance of the parachute. In order to verify the performance of the DBG on MSL, experimental testing, including acquisition of Stereo Particle Imaging Velocimetry (PIV) measurements were required for validating CFD predictions of the parachute performance. A rigid model of the DBG parachute was tested in the 10x10 foot wind tunnel at GRC. Prior to the MSL tests, a PIV system had never been used in the 10x10 wind tunnel. In this paper we discuss some of the technical challenges overcome in implementing a Stereo PIV system with a 750x400 mm field-of-view in the 10x10 wind tunnel facility and results from the MSL hardshell canopy tests.

Process, Structure, and Properties of Electrospun Carbon Nanotube-Reinforced Nanocomposite Yarns

Directory of Open Access Journals (Sweden)

Nasir M. Uddin

2009-01-01

Full Text Available Carbon nanotubes (CNTs are dispersed into polyacrylonitrile polymer solution and then assembled into continuous nanocomposite yarns through the drum-tape co-electrospinning process to facilitate the translation of CNT properties to higher order structures. We explore the dispersion of CNTs in a polymer matrix, the process of obtaining continuous yarn through electrospinning, and the surface morphology and mechanical properties of the nanocomposite yarn.

Analyzing the Effect of Spinning Process Variables on Draw Frame Blended Cotton Mélange Yarn Quality

Science.gov (United States)

Ray, Suchibrata; Ghosh, Anindya; Banerjee, Debamalya

2017-12-01

An investigation has been made to study the effect of important spinning process variables namely shade depth, ring frame spindle speed and yarn twist multiplier (TM) on various yarn quality parameters like unevenness, strength, imperfection, elongation at break and hairiness index of draw frame blended cotton mélange yarn. Three factors Box and Behnken design of experiment has been used to conduct the study. The quadratic regression model is used to device the statistical inferences about sensitivity of the yarn quality parameters to the different process variables. The response surfaces are constructed for depicting the geometric representation of yarn quality parameters plotted as a function of process variables. Analysis of the results show that yarn strength of draw frame blended cotton mélange yarn is significantly affected by shade depth and TM. Yarn unevenness is affected by shade depth and ring frame spindle speed. Yarn imperfection level is mainly influenced by the shade depth and spindle speed. The shade depth and yarn TM have shown significant impact on yarn hairiness index.

Azadirachta indica Mediated Bioactive Lyocell Yarn: Chemical and Colour Characterization

Directory of Open Access Journals (Sweden)

B. H. Patel

2014-01-01

Full Text Available The study deals with preparing aesthetic textiles using methanolic extract of Azadirachta indica leaves. The extract with metallic and natural mordents was utilized to create various shades on lyocell yarn using exhaust technique of dyeing. Aesthetic values of dyed yarns were analyzed in terms of colourimetric parameters, that is, CIE L*  a*  b* and colour fastness. The attachment of Azadirachta indica compounds has been confirmed by using infrared spectroscopy (IR analysis. The dyed samples exhibit moderate to good fastness properties. The study showed that lyocell yarn treated at 15% (owf methanolic extract of Azadirachta indica leaves can be utilized as effective bioactive textiles. Azadirachta indica is an alternative to synthetic antimicrobial agents. This bioactive yarn can be used in fashion as well as in medicinal industry.

High performance electrochemical and electrothermal artificial muscles from twist-spun carbon nanotube yarn

Science.gov (United States)

Lee, Jae Ah; Baughman, Ray H.; Kim, Seon Jeong

2015-04-01

High performance torsional and tensile artificial muscles are described, which utilize thermally- or electrochemically-induced volume changes of twist-spun, guest-filled, carbon nanotube (CNT) yarns. These yarns were prepared by incorporating twist in carbon nanotube sheets drawn from spinnable CNT forests. Inserting high twist into the CNT yarn results in yarn coiling, which can dramatically amplify tensile stroke and work capabilities compared with that for the non-coiled twisted yarn. When electrochemically driven in a liquid electrolyte, these artificial muscles can generate a torsional rotation per muscle length that is over 1000 times higher than for previously reported torsional muscles. All-solid-state torsional electrochemical yarn muscles have provided a large torsional muscle stroke (53° per mm of yarn length) and a tensile stroke of up to 1.3% when lifting loads that are ~25 times heavier than can be lifted by the same diameter human skeletal muscle. Over a million torsional and tensile actuation cycles have been demonstrated for thermally powered CNT hybrid yarns muscles filled with paraffin wax, wherein a muscle spins a rotor at an average 11,500 revolutions/minute or delivers 3% tensile contraction at 1200 cycles/minute. At lower actuation rates, these thermally powered muscles provide tensile strokes of over 10%.

Damping Effects of Drogue Parachutes on Orion Crew Module Dynamics

Science.gov (United States)

Aubuchon, Vanessa V.; Owens, D. Bruce

2016-01-01

Because simulations of the Orion Crew Module (CM) dynamics with drogue parachutes deployed were under-predicting the amount of damping seen in free-flight tests, an attach-point damping model was applied to the Orion system. A key hypothesis in this model is that the drogue parachutes' net load vector aligns with the CM drogue attachment point velocity vector. This assumption seems reasonable and has historically produced good results, but has never been experimentally verified. The wake of the CM influences the drogue parachutes, which makes performance predictions of the parachutes difficult. Many of these effects are not currently modeled in the simulations. A forced oscillation test of the CM with parachutes was conducted in the NASA LaRC 20-Ft Vertical Spin Tunnel (VST) to gather additional data to validate and refine the attach-point damping model. A second loads balance was added to the original Orion VST model to measure the drogue parachute loads independently of the CM. The objective of the test was to identify the contribution of the drogues to CM damping and provide additional information to quantify wake effects and the interactions between the CM and parachutes. The drogue parachute force vector was shown to be highly dependent on the CM wake characteristics. Based on these wind tunnel test data, the attach-point damping model was determined to be a sufficient approximation of the parachute dynamics in relationship to the CM dynamics for preliminary entry vehicle system design. More wake effects should be included to better model the system.

Hybrid carbon nanotube yarn artificial muscle inspired by spider dragline silk.

Science.gov (United States)

Chun, Kyoung-Yong; Hyeong Kim, Shi; Kyoon Shin, Min; Hoon Kwon, Cheong; Park, Jihwang; Tae Kim, Youn; Spinks, Geoffrey M; Lima, Márcio D; Haines, Carter S; Baughman, Ray H; Jeong Kim, Seon

2014-01-01

Torsional artificial muscles generating fast, large-angle rotation have been recently demonstrated, which exploit the helical configuration of twist-spun carbon nanotube yarns. These wax-infiltrated, electrothermally powered artificial muscles are torsionally underdamped, thereby experiencing dynamic oscillations that complicate positional control. Here, using the strategy spiders deploy to eliminate uncontrolled spinning at the end of dragline silk, we have developed ultrafast hybrid carbon nanotube yarn muscles that generated a 9,800 r.p.m. rotation without noticeable oscillation. A high-loss viscoelastic material, comprising paraffin wax and polystyrene-poly(ethylene-butylene)-polystyrene copolymer, was used as yarn guest to give an overdamped dynamic response. Using more than 10-fold decrease in mechanical stabilization time, compared with previous nanotube yarn torsional muscles, dynamic mirror positioning that is both fast and accurate is demonstrated. Scalability to provide constant volumetric torsional work capacity is demonstrated over a 10-fold change in yarn cross-sectional area, which is important for upscaled applications.

Ultrafast charge and discharge biscrolled yarn supercapacitors for textiles and microdevices

Science.gov (United States)

Lee, Jae Ah; Shin, Min Kyoon; Kim, Shi Hyeong; Cho, Hyun U.; Spinks, Geoffrey M.; Wallace, Gordon G.; Lima, Márcio D.; Lepró, Xavier; Kozlov, Mikhail E.; Baughman, Ray H.; Kim, Seon Jeong

2013-06-01

Flexible, wearable, implantable and easily reconfigurable supercapacitors delivering high energy and power densities are needed for electronic devices. Here we demonstrate weavable, sewable, knottable and braidable yarns that function as high performance electrodes of redox supercapacitors. A novel technology, gradient biscrolling, provides fast-ion-transport yarn in which hundreds of layers of conducting-polymer-infiltrated carbon nanotube sheet are scrolled into ~20 μm diameter yarn. Plying the biscrolled yarn with a metal wire current collector increases power generation capabilities. The volumetric capacitance is high (up to ~179 F cm-3) and the discharge current of the plied yarn supercapacitor linearly increases with voltage scan rate up to ~80 V s-1 and ~20 V s-1 for liquid and solid electrolytes, respectively. The exceptionally high energy and power densities for the complete supercapacitor, and high cycle life that little depends on winding or sewing (92%, 99% after 10,000 cycles, respectively) are important for the applications in electronic textiles.

Reverse Launch Abort System Parachute Architecture Trade Study

Science.gov (United States)

Litton, Daniel K.; O'Keefe, Stephen A.; Winski, Richard G.

2011-01-01

This study investigated a potential Launch Abort System (LAS) Concept of Operations and abort parachute architecture. The purpose of the study was to look at the concept of jettisoning the LAS tower forward (Reverse LAS or RLAS) into the free-stream flow rather than after reorienting to a heatshield forward orientation. A hypothesized benefit was that due to the compressed timeline the dynamic pressure at main line stretch would be substantially less. This would enable the entry parachutes to be designed and sized based on entry loading conditions rather than the current stressing case of a Pad Abort. Ultimately, concerns about the highly dynamic reorientation of the CM via parachutes, and the additional requirement of a triple bridle attachment for the RLAS parachute system, overshadowed the potential benefits and ended this effort.

Comparative Investigation of Mechanical–Physical Characteristics of Biodegradable and Non-Degradable Yarns

Directory of Open Access Journals (Sweden)

Krikštanavičienė Kira

2014-06-01

Full Text Available This article presents the results from investigations of tensile tests, absorbency test and degradation test of biodegradable and non- or partly biodegradable yarns produced from pure poly hydroxybutyrate-co-valerate (PHBV, poly (lactide acid (PLA, isotactic polypropylene (iPP polymers and their blends. The results indicate that mechanical-physical properties of PHBV are improved by adding PLA and iPP to PHBV. The main results indicate that the PHBV/PLA and PHBV/iPP (70/30 blends had better mechanical properties than pure PHBV, as well as improved immiscibility and the same or lower degradation in sodium chloride solution, respectively. The PHBV/PLA and PHBV/iPP blends showed a tendency for lower crystallinity and stiffness of the yarns, rendering them less stiff and fragile. The absorption tests showed that absorption dynamic process depends on the structure and raw materials of the yarns. The disinfectant in all samples is absorbed faster than blood. Research results showed that pure PHBV yarns have good hydrophobic properties, compared with pure PLA and iPP yarns. The use of additional PLA and iPP polymers changed the wetting behaviour of yarns. Absorption time of blended yarns in disinfectant liquid decreases and absorption time in the case of blood significantly increases in comparison with PLA and iPP yarns and decreases compared with PHBV yarns. The degradation tests (within 90 days in a solution of sodium chloride showed that pure PHBV and PHBV/PLA blends degraded at different rates but with the loss of the same weight, while pure PHBV and PHBV/iPP blends degraded at the same rate, but PHBV/iPP blends had worse destruction results. Such improvements are expected to be important for the practical application of PHBV in some fields

75 FR 47236 - Golden Parachute and Indemnification Payments

Science.gov (United States)

2010-08-05

... golden parachute, severance, indemnification or other agreement. Claims for employee welfare benefits or... legitimate employee severance payments and improper golden parachute payments. DATES: Comments must be... FICUs with greater clarity on the distinction between legitimate employee severance payments and...

Machine-Washable PEDOT:PSS Dyed Silk Yarns for Electronic Textiles.

Science.gov (United States)

Ryan, Jason D; Mengistie, Desalegn Alemu; Gabrielsson, Roger; Lund, Anja; Müller, Christian

2017-03-15

Durable, electrically conducting yarns are a critical component of electronic textiles (e-textiles). Here, such yarns with exceptional wear and wash resistance are realized through dyeing silk from the silkworm Bombyx mori with the conjugated polymer:polyelectrolyte complex PEDOT:PSS. A high Young's modulus of approximately 2 GPa combined with a robust and scalable dyeing process results in up to 40 m long yarns that maintain their bulk electrical conductivity of approximately 14 S cm -1 when experiencing repeated bending stress as well as mechanical wear during sewing. Moreover, a high degree of ambient stability is paired with the ability to withstand both machine washing and dry cleaning. For the potential use for e-textile applications to be illustrated, an in-plane thermoelectric module that comprises 26 p-type legs is demonstrated by embroidery of dyed silk yarns onto a piece of felted wool fabric.

THE OPTIMIZATION OF PLUSH YARNS BULKING PROCESS

Directory of Open Access Journals (Sweden)

VINEREANU Adam

2014-05-01

Full Text Available This paper presents the experiments that were conducted on the installation of continuous bulking and thermofixing “SUPERBA” type TVP-2S for optimization of the plush yarns bulking process. There were considered plush yarns Nm 6.5/2, made of the fibrous blend of 50% indigenous wool sort 41 and 50% PES. In the first stage, it performs a thermal treatment with a turboprevaporizer at a temperature lower than thermofixing temperature, at atmospheric pressure, such that the plush yarns - deposed in a freely state on a belt conveyor - are uniformly bulking and contracting. It was followed the mathematical modeling procedure, working with a factorial program, rotatable central composite type, and two independent variables. After analyzing the parameters that have a direct influence on the bulking degree, there were selected the pre-vaporization temperature (coded x1,oC and the velocity of belt inside pre-vaporizer (coded x 2, m/min. As for the dependent variable, it was chosen the plush yarn diameter (coded y, mm. There were found the coordinates of the optimal point, and then this pair of values was verified in practice. These coordinates are: x1optim= 90oC and x 2optim= 6.5 m/min. The conclusion is that the goal was accomplished: it was obtained a good cover degree f or double-plush carpets by reducing the number of tufts per unit surface.

Full-field fabric stress mapping by micro Raman spectroscopy in a yarn push-out test.

Science.gov (United States)

Lei, Z K; Qin, F Y; Fang, Q C; Bai, R X; Qiu, W; Chen, X

2018-02-01

The full-field stress distribution of a two-dimensional plain fabric was mapped using micro Raman spectroscopy (MRS) through a novel yarn push-out test, simulating a quasi-static projectile impact on the fabric. The stress-strain relationship for a single yarn was established using a digital image correlation method in a single-yarn tensile test. The relationship between Raman peak shift and aramid Kevlar 49 yarn stress was established using MRS in a single-yarn tensile test. An out-of-plane loading test was conducted on an aramid Kevlar 49 plain fabric, and the yarn stress was measured using MRS. From the full-field fabric stress distribution, it can be observed that there is a cross-shaped distribution of high yarn stress; this result would be helpful in further studies on load transfer on a fabric during a projectile impact.

VISCOSE BASED MAGNETIC YARNS – PHYSICAL AND MECHANICAL CHARACTERIZATION

Directory of Open Access Journals (Sweden)

GROSU Marian-Cătălin

2017-05-01

Full Text Available In the context of the rapid growth in the number of electrical and electronic devices and accessories that emit electromagnetic energy in different frequency bands we present and characterize here several magnetic functionalized viscose twisted yarns. A 100% viscose twisted staple yarn was covered through an in-house developed process with a polymeric solution containing micrometric sized barium hexaferrite magnetic powder. The in-house developed process allows deposition of micrometric thickness polymeric paste layer on the yarn surface. Barium hexaferrite is a hard magnetic material exhibiting high chemical stability and corrosion resistivity, relatively large saturation and residual magnetization and microwave absorbing properties. Five different percentages of the magnetic powder in the polymer solution were used, i.e. ranging from 15 wt% to 45 wt%. Physical characterization shows a very good adherence between the highly hygroscopic viscose staple fibers and the polymeric solution that contains polyvinyl acetate and polyurethane as binders. SEM images evidenced the fact that the polymeric solution penetrated more than 1/3 of the yarn diameter. The concentration of magnetic powder in the polymeric solution has a direct influence on the coating amount, diameter and density. The mechanical characterization of the coated yarns revealed that the breaking force is increasing with increasing magnetic powder content up to o certain value and then decreased because the magnetic layer became stiffer. At the same time, the elongation at brake is decreasing.

Aerodynamic Reconstruction Applied to Parachute Test Vehicle Flight Data Analysis

Science.gov (United States)

Cassady, Leonard D.; Ray, Eric S.; Truong, Tuan H.

2013-01-01

The aerodynamics, both static and dynamic, of a test vehicle are critical to determining the performance of the parachute cluster in a drop test and for conducting a successful test. The Capsule Parachute Assembly System (CPAS) project is conducting tests of NASA's Orion Multi-Purpose Crew Vehicle (MPCV) parachutes at the Army Yuma Proving Ground utilizing the Parachute Test Vehicle (PTV). The PTV shape is based on the MPCV, but the height has been reduced in order to fit within the C-17 aircraft for extraction. Therefore, the aerodynamics of the PTV are similar, but not the same as, the MPCV. A small series of wind tunnel tests and computational fluid dynamics cases were run to modify the MPCV aerodynamic database for the PTV, but aerodynamic reconstruction of the flights has proven an effective source for further improvements to the database. The acceleration and rotational rates measured during free flight, before parachute inflation but during deployment, were used to con rm vehicle static aerodynamics. A multibody simulation is utilized to reconstruct the parachute portions of the flight. Aerodynamic or parachute parameters are adjusted in the simulation until the prediction reasonably matches the flight trajectory. Knowledge of the static aerodynamics is critical in the CPAS project because the parachute riser load measurements are scaled based on forebody drag. PTV dynamic damping is critical because the vehicle has no reaction control system to maintain attitude - the vehicle dynamics must be understood and modeled correctly before flight. It will be shown here that aerodynamic reconstruction has successfully contributed to the CPAS project.

Structure and yarn sensor for fabric

Science.gov (United States)

Mee, D.K.; Allgood, G.O.; Mooney, L.R.; Duncan, M.G.; Turner, J.C.; Treece, D.A.

1998-10-20

A structure and yarn sensor for fabric directly determines pick density in a fabric thereby allowing fabric length and velocity to be calculated from a count of the picks made by the sensor over known time intervals. The structure and yarn sensor is also capable of detecting full length woven defects and fabric. As a result, an inexpensive on-line pick (or course) density measurement can be performed which allows a loom or knitting machine to be adjusted by either manual or automatic means to maintain closer fiber density tolerances. Such a sensor apparatus dramatically reduces fabric production costs and significantly improves fabric consistency and quality for woven or knitted fabric. 13 figs.

Investigation on the Yarn Squeezing Effect of Three Dimensional Full Five Directional Braided Composites

Science.gov (United States)

Hu, Long; Tao, Guoquan; Liu, Zhenguo; Wang, Yibo; Ya, Jixuan

2018-04-01

The influence of yarn squeezing effect on the geometric morphology and mechanical property of the three dimensional full five directional (3DF5D) braided composites is explored. Spatial path and cross-section shape of the yarns in the braided structure are characterized based on the micro computed tomography (micro CT) scanning images. The yarn distortion due to the squeezing effect is discussed and mathematical morphology of the yarn geometry is established. A new repeated unit cell (RUC) model of 3DF5D braided composites considering yarn squeezing effect is developed. Based on this model, mechanical properties of 3DF5D braided composites are analyzed. Good agreement is obtained between the predicted and experiment results. Moreover, the stress distribution of the new RUC model are compared with original RUC model, showing that the squeezing effect significantly increases the stress concentration level of the axial yarns.

Functional Elastic Knits Made of Bamboo Charcoal and Quick-Dry Yarns: Manufacturing Techniques and Property Evaluations

Directory of Open Access Journals (Sweden)

Jia-Horng Lin

2017-12-01

Full Text Available Conventional sportswear fabrics are functional textiles that can mitigate the impaired muscles caused by exercises for the wearers, but they can also cause discomfort and skin allergy. This study proposes combining two yarns to form functional composite yarns, by using a twisting or wrapping process. Moreover, a different twist number is used in order to adjust the performance of functional composite yarns. A crochet machine is used to make the functional composite yarns into functional elastic knits that are suitable for use in sportswear. The test results show that, in comparison to the non-processed yarns, using the twisted or wrapped yarns can considerably decrease the water vapor transmission rate of functional elastic knits by 38%, while also improving their far infrared emissivity by 13%, water absorption rate by 39%, and air permeability by 136%. In particular, the functional elastic knits that are made of B-wrapped yarns (bamboo charcoal- wrapped yarns, composed of 20 twists per inch, have the optimal diverse functions.

Parachute Cord Tension Sensor

Data.gov (United States)

National Aeronautics and Space Administration — To design and fabricate a light weight (few oz), very small (~2 inch length) parachute cord tension sensor demonstrator device.A major challenge for the CPAS (The...

Study of Pressure Oscillations in Supersonic Parachute

Science.gov (United States)

Dahal, Nimesh; Fukiba, Katsuyoshi; Mizuta, Kazuki; Maru, Yusuke

2018-04-01

Supersonic parachutes are a critical element of planetary mission whose simple structure, light-weight characteristics together with high ratio of aerodynamic drag makes them the most suitable aerodynamic decelerators. The use of parachute in supersonic flow produces complex shock/shock and wake/shock interaction giving rise to dynamic pressure oscillations. The study of supersonic parachute is difficult, because parachute has very flexible structure which makes obtaining experimental pressure data difficult. In this study, a supersonic wind tunnel test using two rigid bodies is done. The wind tunnel test was done at Mach number 3 by varying the distance between the front and rear objects, and the distance of a bundle point which divides suspension lines and a riser. The analysis of Schlieren movies revealed shock wave oscillation which was repetitive and had large pressure variation. The pressure variation differed in each case of change in distance between the front and rear objects, and the change in distance between riser and the rear object. The causes of pressure oscillation are: interaction of wake caused by front object with the shock wave, fundamental harmonic vibration of suspension lines, interference between shock waves, and the boundary layer of suspension lines.

Flexible supercapacitor yarns with coaxial carbon nanotube network electrodes

International Nuclear Information System (INIS)

Smithyman, Jesse; Liang, Richard

2014-01-01

Graphical abstract: - Highlights: • Fabricated flexible yarn supercapacitor with coaxial electrodes. • Use of multifunctional carbon nanotube network electrodes eliminates inactive components and enables high energy/power density. • Robust structure maintains >95% of energy/power while under deformation. - Abstract: Flexible supercapacitors with a yarn-like geometry were fabricated with coaxially arranged electrodes. Carbon nanotube (CNT) network electrodes enabled the integration of the electronic conductor and active material of each electrode into a single component. CNT yarns were employed as the inner electrode to provide the supporting structure of the device. These part integration strategies eliminated the need for inactive material, which resulted in device volumetric energy and power densities among the highest reported for flexible carbon-based EDLCs. In addition, the coaxial yarn cell design provided a robust structure able to undergo flexural deformation with minimal impact on the energy storage performance. Greater than 95% of the energy density and 99% of the power density were retained when wound around an 11 cm diameter cylinder. The electrochemical properties were characterized at stages throughout the fabrication process to provide insights and potential directions for further development of these novel cell designs

Ultrafine PBI fibers and yarns

Science.gov (United States)

Leal, J. R.; Tan, M.

1979-01-01

Gentle precisely controlled process is used to draw polybenzimidazole (PBI) fibers to denier as low as 0.17 per fiber. Yarns of lightweight fibers could be useful in applications where lightweight textiles must withstand high temperatures, corrosion, or radiation.

Humidity Induces Changes in the Dimensions of Hydrogel-Coated Wool Yarns

Directory of Open Access Journals (Sweden)

Lanlan Wang

2018-03-01

Full Text Available Polymeric hydrogel based on acrylic acid (AA and N,N-dimethylacrylamide (DMAA was prepared by photopolymerization reaction, using nano-alumina as the inorganic crosslinker. Hydrogel-coated wool yarns determine their dimensional changes under humidity conditions. Surface morphology of the hydrogel-coated wool yarns was carried out using SEM microscopy. The hydrogel was further characterized by Fourier transformer infrared spectrum (FTIR, gel permeation chromatography (GPC, differential scanning calorimetry (DSC, thermogravimetry (TG and differential thermogravimetry (DTG. This contribution showed that UV-initiated polymerization coating wool yarns can change the functional properties of wool fibers.

Influence of yarn folding on UV protection properties of hemp knitted fabrics

Directory of Open Access Journals (Sweden)

Kocić Ana A.

2016-01-01

Full Text Available In the last years the media have highlighted the damage of the ozone layer and the resulting increase of ultraviolet radiation (UVR reaching the earth’s surface. Prolonged and repeated, both occupational and recreational, sun exposure of the population causes some detrimental effects. Clothing is considered to be one of the most important tools for UV protection. It is generally accepted that synthetic fibres provide a high UV protection capability of textiles, while cellulose fibres (cotton, linen, hemp, viscose have a low UV absorption capacity. However, natural pigments, pectin and waxes in natural cellulose fibers, and lignin in hemp fibers, act as UV absorbers having a favorable effect on UPF of grey-state fabrics. Bearing in mind the trend of reintroduction of hemp fibers as a source of eco-friendly textiles, there is a serious lack of study about the potential of hemp materials in terms of UV protection. Folded yarn is a complex yarn composed of two or more component yarns arranged parallel and twisted together to make a “new quality” yarn. Folding of yarns is an operation undertaken in order to modify single-yarn properties to an appreciable degree. There are very few investigations concerning the relationship between the yarn properties and UV protection effectiveness of the fabric made there from. In addition, there is no any result in the scientific literature about the influence of yarn folding on UV protection properties of textile materials. Having this in mind, for our research the idea was to evaluate the effect of yarn folding in this regard. The plain knitted fabrics composed of single or two-folded hemp yarn were compared in terms of UV protection properties. The Ultraviolet Protection Factor (UPF, as the quantitative measurement of the material effectiveness to protect the human skin against UVR, was determined for the textile materials by in vitro test method according to the European standard EN 13758. The knitted

Investigations on the Manufacturing and Mechanical Properties of Spun Yarns Made from Staple CF for Thermoset Composites

Directory of Open Access Journals (Sweden)

Hasan Mir Mohammad Badrul

2017-12-01

Full Text Available This article reports the results of investigations carried out to produce yarns consisting of staple carbon fiber (CF obtained from process waste for the manufacturing of composites suitable especially for thermoset applications. For this purpose, a comparative analysis is done on processability between 100% staple CF and 60 weight% staple CF mixed with 40 weight% PVA fibers in carding, drawing and spinning process. The hybrid yarns are produced by varying twist level. The PVA fibers of the hybrid yarn are then dissolved using hot water treatment. The mechanical properties of yarns consisting of 100% staple CF and hybrid yarns consisting of staple CF and PVA before and after hot water treatment are investigated. Furthermore, test specimen is also prepared by impregnating 100% staple CF yarn and the hybrid yarns (after the dissolving of PVA with epoxy resin. The results of the tensile test of the yarns in consolidated state reveals that the hybrid yarn produced with 80 T/m after hot water treatment exhibits approximately 75% of the tensile strength of virgin filament tow, and it is expected that the hybrid yarns can be applied for the manufacturing of thermoset based composites for load bearing structures.

14 CFR 65.115 - Senior parachute rigger certificate: Experience, knowledge, and skill requirements.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Senior parachute rigger certificate... CREWMEMBERS Parachute Riggers § 65.115 Senior parachute rigger certificate: Experience, knowledge, and skill requirements. Except as provided in § 65.117, an applicant for a senior parachute rigger certificate must— (a...

Carbon Nanotube Yarn-Based Glucose Sensing Artificial Muscle.

Science.gov (United States)

Lee, Junghan; Ko, Sachan; Kwon, Cheong Hoon; Lima, Márcio D; Baughman, Ray H; Kim, Seon Jeong

2016-04-01

Boronic acid (BA), known to be a reversible glucose-sensing material, is conjugated to a nanogel (NG) derived from hyaluronic acid biopolymer and used as a guest material for a carbon multiwalled nanotube (MWNT) yarn. By exploiting the swelling/deswelling of the NG that originates from the internal anionic charge changes resulting from BA binding to glucose, a NG MWNT yarn artificial muscle is obtained that provides reversible torsional actuation that can be used for glucose sensing. This actuator shows a short response time and high sensitivity (in the 5-100 × 10(-3) m range) for monitoring changes in glucose concentration in physiological buffer, without using any additional auxiliary substances or an electrical power source. It may be possible to apply the glucose-sensing MWNT yarn muscles as implantable glucose sensors that automatically release drugs when needed or as an artificial pancreas. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Risk Factors for Parachute Injuries and Airborne Student Observations on the Parachute Ankle Brace

National Research Council Canada - National Science Library

Knapik, Joseph J; Spiess, Anita; Darakjy, Salima; Grier, Tyson; Manning, Fred; Livingston, Elaine; Swedler, David; Amoroso, Paul; Jones, Bruce H

2007-01-01

...) of the Defense Safety Oversight Council (DSOC) to evaluate the parachute ankle brace (PAB). Information provided by the questionnaire identified potential injury risk factors and comments on the PAB...

Rocket-Powered Parachutes Rescue Entire Planes

Science.gov (United States)

2010-01-01

Small Business Innovation Research (SBIR) contracts with Langley Research Center helped BRS Aerospace, of Saint Paul, Minnesota, to develop technology that has saved 246 lives to date. The company s whole aircraft parachute systems deploy in less than 1 second thanks to solid rocket motors and are capable of arresting the descent of a small aircraft, lowering it safely to the ground. BRS has sold more than 30,000 systems worldwide, and the technology is now standard equipment on many of the world s top-selling aircraft. Parachutes for larger airplanes are in the works.

Modeling and Experiments on Ballistic Impact into UHMWPE Yarns Using Flat and Saddle-Nosed Projectiles

Directory of Open Access Journals (Sweden)

Stuart Leigh Phoenix

2017-03-01

Full Text Available Yarn shooting experiments were conducted to determine the ballistically-relevant, Young’s modulus and tensile strength of ultra-high molecular weight polyethylene (UHMWPE fiber. Target specimens were Dyneema® SK76 yarns (1760 dtex, twisted to 40 turns/m, and initially tensioned to stresses ranging from 29 to 2200 MPa. Yarns were impacted, transversely, by two types of cylindrical steel projectiles at velocities ranging from 150 to 555 m/s: (i a reverse-fired, fragment simulating projectile (FSP where the flat rear face impacted the yarn rather than the beveled nose; and (ii a ‘saddle-nosed projectile’ having a specially contoured nose imparting circular curvature in the region of impact, but opposite curvature transversely to prevent yarn slippage off the nose. Experimental data consisted of sequential photographic images of the progress of the triangular transverse wave, as well as tensile wave speed measured using spaced, piezo-electric sensors. Yarn Young’s modulus, calculated from the tensile wave-speed, varied from 133 GPa at minimal initial tension to 208 GPa at the highest initial tensions. However, varying projectile impact velocity, and thus, the strain jump on impact, had negligible effect on the modulus. Contrary to predictions from the classical Cole-Smith model for 1D yarn impact, the critical velocity for yarn failure differed significantly for the two projectile types, being 18% lower for the flat-faced, reversed FSP projectile compared to the saddle-nosed projectile, which converts to an apparent 25% difference in yarn strength. To explain this difference, a wave-propagation model was developed that incorporates tension wave collision under blunt impact by a flat-faced projectile, in contrast to outward wave propagation in the classical model. Agreement between experiment and model predictions was outstanding across a wide range of initial yarn tensions. However, plots of calculated failure stress versus yarn pre

Coaxial wet-spun yarn supercapacitors for high-energy density and safe wearable electronics

Science.gov (United States)

Kou, Liang; Huang, Tieqi; Zheng, Bingna; Han, Yi; Zhao, Xiaoli; Gopalsamy, Karthikeyan; Sun, Haiyan; Gao, Chao

2014-01-01

Yarn supercapacitors have great potential in future portable and wearable electronics because of their tiny volume, flexibility and weavability. However, low-energy density limits their development in the area of wearable high-energy density devices. How to enhance their energy densities while retaining their high-power densities is a critical challenge for yarn supercapacitor development. Here we propose a coaxial wet-spinning assembly approach to continuously spin polyelectrolyte-wrapped graphene/carbon nanotube core-sheath fibres, which are used directly as safe electrodes to assembly two-ply yarn supercapacitors. The yarn supercapacitors using liquid and solid electrolytes show ultra-high capacitances of 269 and 177 mF cm−2 and energy densities of 5.91 and 3.84 μWh cm−2, respectively. A cloth supercapacitor superior to commercial capacitor is further interwoven from two individual 40-cm-long coaxial fibres. The combination of scalable coaxial wet-spinning technology and excellent performance of yarn supercapacitors paves the way to wearable and safe electronics. PMID:24786366

Coaxial wet-spun yarn supercapacitors for high-energy density and safe wearable electronics

Science.gov (United States)

Kou, Liang; Huang, Tieqi; Zheng, Bingna; Han, Yi; Zhao, Xiaoli; Gopalsamy, Karthikeyan; Sun, Haiyan; Gao, Chao

2014-05-01

Yarn supercapacitors have great potential in future portable and wearable electronics because of their tiny volume, flexibility and weavability. However, low-energy density limits their development in the area of wearable high-energy density devices. How to enhance their energy densities while retaining their high-power densities is a critical challenge for yarn supercapacitor development. Here we propose a coaxial wet-spinning assembly approach to continuously spin polyelectrolyte-wrapped graphene/carbon nanotube core-sheath fibres, which are used directly as safe electrodes to assembly two-ply yarn supercapacitors. The yarn supercapacitors using liquid and solid electrolytes show ultra-high capacitances of 269 and 177 mF cm-2 and energy densities of 5.91 and 3.84 μWh cm-2, respectively. A cloth supercapacitor superior to commercial capacitor is further interwoven from two individual 40-cm-long coaxial fibres. The combination of scalable coaxial wet-spinning technology and excellent performance of yarn supercapacitors paves the way to wearable and safe electronics.

Cause Analyses of Yarn Defect%纱线疵点产生原因分析

Institute of Scientific and Technical Information of China (English)

王充; 赵帆

2016-01-01

The grading and cause of yarn defect in the process of electronic yarn cleaner were discussed.The definition and classification of yarn defects were introduced.Yarns with thick place and thin places were identified according to different shapes of yarn with defects and refering the basic diameters of yarn aimed at the cleaning technology in winding.Combined the yarn defect classifing area,the frequency distribution chart of yarn defect was analyzed,the possible causes of defects in each areas were pointed out.It is considered that the problems in each processing can be effectively analyzed through the yarn cleaning data from winding electronic yarn cleaner. The quality problems can be quickly positioned and solved,the quality managing efficiency can be improved.%探讨电子清纱器工作过程中纱线疵点的分级和产生原因。介绍了纱线疵点的定义和分类，针对络筒清纱工艺，根据疵点纱的不同形状并参考细纱的基础直径，识别粗节纱和细节纱。结合纱线疵点分级区域，分析了纱线疵点频率分布图，指出了各个区域疵点可能产生的原因。认为：通过络筒电子清纱器的清纱数据，可以有效分析各个工艺环节出现的问题，帮助快速定位和解决质量问题，提高质量管理的效率。

THE INFLUENCE OF THE NUMBER OF RIPPLE OF POLYACRYLONITRILIC FIBERS COTTON TYPE ON YARN PROPERTIES

Directory of Open Access Journals (Sweden)

HRISTIAN Liliana

2016-05-01

Full Text Available In this study we aimed the influence of the number of undulations of polyacrylonitrile fibers, cotton type, on the properties of yarns with Nm50/1 fineness, made on BD 200 the rotor spinning machine. Rotor spinning of the synthetic fibers is largely influenced by some characteristics of the fibers as being: the quality and quantity of the avivage, frequency of undulations and the number of defects fiber. Tensile properties and structural characteristics aspect of the yarns carried on BD 200 rotor spinning machine are determined, at the fiber content, the structural model and the technological parameters of processing, by the result of the transfer of fibers proprieties, into the meaning fiber-yarn. The yarns structural compactness, determined by the degree of twisting and tensional properties are defining for the quality of yarns and warrants the corresponding to their destination. Structural characteristics of the yarns which are characterized by complexity and diversity of their actions were studied by determining the linear irregularity (U% , standard deviation (CV% and the imperfections in the form of thinning (S, thickening (G, neppines (N, relative to 1000 m yarn.

Strain gauge sensors comprised of carbon nanotube yarn: parametric numerical analysis of their piezoresistive response

International Nuclear Information System (INIS)

Abot, Jandro L; Kiyono, César Y; Thomas, Gilles P; Silva, Emílio C N

2015-01-01

Carbon nanotube (CNT) yarns are micron-size fibers that contain thousands of intertwined CNTs in their cross sections and exhibit piezoresistance characteristics that can be tapped for sensing purposes. Sensor yarns can be integrated into polymeric and composite materials to measure strain through resistance measurements without adding weight or altering the integrity of the host material. This paper includes the details of novel strain gauge sensor configurations comprised of CNT yarn, the numerical modeling of their piezoresistive response, and the parametric analysis schemes that determines the highest sensor sensitivity to mechanical loading. The effect of several sensor configuration parameters are discussed including the inclination and separation of the CNT yarns within the sensor, the mechanical properties of the CNT yarn, the direction and magnitude of the applied mechanical load, and the dimensions and shape of the sensor. The sensor configurations that yield the highest sensitivity are presented and discussed in terms of the mechanical and electrical properties of the CNT yarn. It is shown that strain gauge sensors consisting of CNT yarn are sensitive enough to measure strain, and could exhibit even higher gauge factors than those of metallic foil strain gauges. (paper)

Inflation of Unreefed and Reefed Extraction Parachutes

Science.gov (United States)

Ray, Eric S.; Varela, Jose G.

2015-01-01

Data from the Orion and several other test programs have been used to reconstruct inflation parameters for 28 ft Do extraction parachutes as well as the parent aircraft pitch response during extraction. The inflation force generated by extraction parachutes is recorded directly during tow tests but is usually inferred from the payload accelerometer during Low Velocity Airdrop Delivery (LVAD) flight test extractions. Inflation parameters are dependent on the type of parent aircraft, number of canopies, and standard vs. high altitude extraction conditions. For standard altitudes, single canopy inflations are modeled as infinite mass, but the non-symmetric inflations in a cluster are modeled as finite mass. High altitude extractions have necessitated reefing the extraction parachutes, which are best modeled as infinite mass for those conditions. Distributions of aircraft pitch profiles and inflation parameters have been generated for use in Monte Carlo simulations of payload extractions.

Technological study of ring and compact spinning systems for the manufacturing of slub fancy yarn under multiple slub variations and its effect on woven fabric

International Nuclear Information System (INIS)

Mahmood, N.; Iftikhar, M.; Mahmood, T.; Arshad, M.

2009-01-01

Textile technologies are continuously evolving with the objects both of increasing productivity and reducing processing costs, and of creating new products or variants of existing ones. Fashion, in the widest sense of the word mean fulfillment of consumer demands, through the ages constitutes a fundamental and conditional element for the whole textile industry. Fancy yarns present deliberate, decorative continuous or programmed effects of colour and/or form they are used to create some variation in the aesthetic appearance of a fabric. The drafting process is deliberately interrupted through the effect yarn device to produce slubs in the final yarn. The present research study was aimed to evaluate the quality characteristics of slub fancy yarn by changing slub length, inter slub distance, slub thickness and twist multiplier (T.M) at ring and compact spinning systems. (author)

The application of poly(amidoamine dendrimers for modification of jute yarns: Preparation and dyeing properties

Directory of Open Access Journals (Sweden)

Ali Akbar Zolriasatein

2015-03-01

Full Text Available In this study, poly(amidoamine (PAMAM G-2 dendrimer was used for jute yarn. Fourier transform infrared spectroscopy (FT-IR revealed that all carbonyl groups of jute fibers reacted with amino groups of polyamidoamine dendrimers. SEM observation indicated the good dispersion PAMAM dendrimers. Jute yarns pretreated with PAMAM dendrimer displayed markedly enhanced color strength with reactive dyes, even when dyeing had been carried out in the absence of electrolyte or alkali. Dendrimer-treated jute yarn showed much better light-fastness than untreated jute yarn.

Reconstruction of Twist Torque in Main Parachute Risers

Science.gov (United States)

Day, Joshua D.

2015-01-01

The reconstruction of twist torque in the Main Parachute Risers of the Capsule Parachute Assembly System (CPAS) has been successfully used to validate CPAS Model Memo conservative twist torque equations. Reconstruction of basic, one degree of freedom drop tests was used to create a functional process for the evaluation of more complex, rigid body simulation. The roll, pitch, and yaw of the body, the fly-out angles of the parachutes, and the relative location of the parachutes to the body are inputs to the torque simulation. The data collected by the Inertial Measurement Unit (IMU) was used to calculate the true torque. The simulation then used photogrammetric and IMU data as inputs into the Model Memo equations. The results were then compared to the true torque results to validate the Model Memo equations. The Model Memo parameters were based off of steel risers and the parameters will need to be re-evaluated for different materials. Photogrammetric data was found to be more accurate than the inertial data in accounting for the relative rotation between payload and cluster. The Model Memo equations were generally a good match and when not matching were generally conservative.

Electro-spun PLA-PEG-yarns for tissue engineering applications.

Science.gov (United States)

Kruse, Magnus; Greuel, Marc; Kreimendahl, Franziska; Schneiders, Thomas; Bauer, Benedict; Gries, Thomas; Jockenhoevel, Stefan

2018-06-27

Electro-spinning is widely used in tissue-engineered applications mostly in form of non-woven structures. The development of e-spun yarn opens the door for textile fabrics which combine the micro to nanoscale dimension of electro-spun filaments with three-dimensional (3D) drapable textile fabrics. Therefore, the aim of the study was the implementation of a process for electro-spun yarns. Polylactic acid (PLA) and polyethylene glycol (PEG) were spun from chloroform solutions with varying PLA/PEG ratios (100:0, 90:10, 75:25 and 50:50). The yarn samples produced were analyzed regarding their morphology, tensile strength, water uptake and cytocompatibility. It was found that the yarn diameter decreased when the funnel collector rotation was increasd, however, the fiber diameter was not influenced. The tensile strength was also found to be dependent on the PEG content. While samples composed of 100% PLA showed a tensile strength of 2.5±0.7 cN/tex, the tensile strength increased with a decreasing PLA content (PLA 75%/PEG 25%) to 6.2±0.5 cN/tex. The variation of the PEG content also influenced the viscosity of the spinning solutions. The investigation of the cytocompatibility with endothelial cells was conducted for PLA/PEG 90:10 and 75:25 and indicated that the samples are cytocompatible.

ANALYSIS OF THE TENSILE STRENGTH OF 100% WOOL YARN FROM DIFFERENT CLIMATIC AREAS

Directory of Open Access Journals (Sweden)

OANA Dorina

2017-05-01

Full Text Available One of the basic conditions required of yarns is to have enough tensile strength to allow them to be turned into textiles and also to give the final product durability. During processing, threads are subjected to various unavoidable forms of mechanical stress, simple or compounded, but the amount of stress can be kept under control by adjusting the corresponding operating parameters (speed, gauges, push force on the cylinders of the rolling train etc.. The values of the operating parameters of the spinning operation are set so as to obtain uniform products in large scale production, but also to ensure the preservation of the properties of the fibers and yarns, for further processing. To this end we analyzed the tensile strength of three batches of 100% wool yarn meant for knitting, from three different geo-climatic areas. These are fine woolen yarn of 25 tex and torque of 620 twists/meter. The study of the tensile strength was carried out using a Uster R Tensojet 4 (UTj4 tension meter, analyzing ten samples of 500 m from each batch. The statistical and mathematical processing of the data obtained after analyzing the samples indicated that the yarns from South Africa have better tensile strength and a lower mechanical impedance variation coefficient than yarns from Asia and England.

Nanofiber-structured hydrogel yarns with pH-response capacity and cardiomyocyte-drivability for bio-microactuator application.

Science.gov (United States)

Wu, Shaohua; Duan, Bin; Qin, Xiaohong; Butcher, Jonathan T

2017-09-15

Polymeric hydrogels have great potential in soft biological micro-actuator applications. However, inappropriate micro-architecture, non-anisotropy, weak biomechanics, and inferior response behaviors limit their development. In this study, we designed and manufactured novel polyacrylonitrile (PAN)-based hydrogel yarns composed with uniaxially aligned nanofibers. The nanofibrous hydrogel yarns possessed anisotropic architecture and robust mechanical properties with flexibility, and could be assembled into defined scaffold structures by subsequent processes. The as-prepared hydrogel yarns showed excellent pH response behaviors, with around 100% maximum length and 900% maximum diameter changes, and the pH response was completed within several seconds. Moreover, the hydrogel yarns displayed unique cell-responsive abilities to promote the cell adhesion, proliferation, and smooth muscle differentiation of human adipose derived mesenchymal stem cells (HADMSC). Chicken cardiomyocytes were further seeded onto our nanofibrous hydrogel yarns to engineer living cell-based microactuators. Our results demonstrated that the uniaxially aligned nanofibrous networks within the hydrogel yarns were the key characteristics leading to the anisotropic organization of cardiac cells, and improved sarcomere organization, mimicking the cardiomyocyte bundles in the native myocardium. The construct is capable of sustaining spontaneous cardiomyocyte pumping behaviors for 7days. Our PAN-based nanofibrous hydrogel yarns are attractive for creating linear microactuators with pH-response capacity and biological microactuators with cardiomyocyte-drivability. A mechanically robust polyacrylonitrile-based nanofibrous hydrogel yarn is fabricated by using a modified electrospinning setup in combination with chemical modification processes. The as-prepared hydrogel yarn possesses a uniaxially aligned nanofiber microarchitecture and supports a rapid, pH-dependent expansion/contraction response within a few

Nanofibrous Smart Fabrics from Twisted Yarns of Electrospun Piezopolymer.

Science.gov (United States)

Yang, Enlong; Xu, Zhe; Chur, Lucas K; Behroozfar, Ali; Baniasadi, Mahmoud; Moreno, Salvador; Huang, Jiacheng; Gilligan, Jules; Minary-Jolandan, Majid

2017-07-19

Smart textiles are envisioned to make a paradigm shift in wearable technologies to directly impart functionality into the fibers rather than integrating sensors and electronics onto conformal substrates or skin in wearable devices. Among smart materials, piezoelectric fabrics have not been widely reported, yet. Piezoelectric smart fabrics can be used for mechanical energy harvesting, for thermal energy harvesting through the pyroelectric effect, for ferroelectric applications, as pressure and force sensors, for motion detection, and for ultrasonic sensing. We report on mechanical and material properties of the plied nanofibrous piezoelectric yarns as a function of postprocessing conditions including thermal annealing and drawing (stretching). In addition, we used a continuous electrospinning setup to directly produce P(VDF-TrFE) nanofibers and convert them into twisted plied yarns, and demonstrated application of these plied yarns in woven piezoelectric fabrics. The results of this work can be an early step toward realization of piezoelectric smart fabrics.

Developing an Acoustic Sensing Yarn for Health Surveillance in a Military Setting

Directory of Open Access Journals (Sweden)

Theodore Hughes-Riley

2018-05-01

Full Text Available Overexposure to high levels of noise can cause permanent hearing disorders, which have a significant adverse effect on the quality of life of those affected. Injury due to noise can affect people in a variety of careers including construction workers, factory workers, and members of the armed forces. By monitoring the noise exposure of workers, overexposure can be avoided and suitable protective equipment can be provided. This work focused on the creation of a noise dosimeter suitable for use by members of the armed forces, where a discrete dosimeter was integrated into a textile helmet cover. In this way the sensing elements could be incorporated very close to the ears, providing a highly representative indication of the sound level entering the body, and also creating a device that would not interfere with military activities. This was achieved by utilising commercial microelectromechanical system microphones integrated within the fibres of yarn to create an acoustic sensing yarn. The acoustic sensing yarns were fully characterised over a range of relevant sound levels and frequencies at each stage in the yarn production process. The yarns were ultimately integrated into a knitted helmet cover to create a functional acoustic sensing helmet cover prototype.

Recent researches concerning the obtaining of functional textiles based on conductive yarns

Science.gov (United States)

Leon, A. L.; Manea, L. R.; Hristian, L.

2016-08-01

Modem textile industry is influenced both by consumers' lifestyle and by novel materials. Functional textiles can be included into the group of technical textiles. The functional activity can be shortly interpreted as "sense - react - adapt" to the environment while traditional materials meet only passive protective role, a barrier between body and environment. Functional materials cross the conventional limits because they are designed for specific performances, being part of domains as: telemedicine, medicine, aeronautics, biotechnology, nanotechnology, protective clothes, sportswear, etc. This paper highlights the most recent developments in the field of using conductive yarns for obtaining functional textiles. Conductive fabrics can be done by incorporating into the textile structure the conductive fibers / yarns. The technologies differ from embroidering, sewing, weaving, knitting to braiding and obtaining nonwovens. The conductive fabrics production has a quickly growth because it is a high demand for these textiles used for data transfer in clothing, monitoring vital signs, germ-free garments, brain-computer interface, etc. Nowadays it is of high interest surface treatments of fibers/yarns which can be considered as a novel kind of textile finishing. There are presented some researches related to obtaining conductive yarns by coating PET and PP yarns with PANi conductive polymer.

Moisture Management Behaviour of Knitted Fabric from Structurally Modified Ring and Vortex Spun Yarn

Science.gov (United States)

Sharma, Navendu; Kumar, Pawan; Bhatia, Dinesh; Sinha, Sujit Kumar

2016-10-01

The acceptability of a new product is decided by its performance, level of improvement in quality and economy of production. The basic aim of generating micro pores in a textile structure is to provide better thermo-physiological comfort by enhancing the breathability and hence improving moisture management behaviour. In the present study, an attempt has been made to create a relatively more open structure through removal of a component. A comparative assessment with a homogeneous and parent yarn was also made. Yarns of two linear densities, each from ring and vortex spinning systems were produced using 100 % polyester and 80:20 polyester/cotton blend. The modified yarn was produced by removing a component, viz; cotton, by treatment with sulphuric acid from the blended yarn. The knitted fabric from modified yarn was found to show significant improvement in air permeability, water vapour permeability and total absorbency while the wicking characteristic was found to decline.

Electrical Properties of Conductive Cotton Yarn Coated with Eosin Y Functionalized Reduced Graphene Oxide.

Science.gov (United States)

Kim, Eunju; Arul, Narayanasamy Sabari; Han, Jeong In

2016-06-01

This study reports the fabrication and investigation of the electrical properties of two types of conductive cotton yarns coated with eosin Y or eosin B functionalized reduced graphene (RGO) and bare graphene oxide (GO) using dip-coating method. The surface morphology of the conductive cotton yarn coated with reduced graphene oxide was observed by Scanning Electron Microscope (SEM). Due to the strong electrostatic attractive forces, the negatively charged surface such as the eosin Y functionalized reduced graphene oxide or bare GO can be easily coated to the positively charged polyethyleneimine (PEI) treated cotton yarn. The maximum current for the conductive cotton yarn coated with eosin Y functionalized RGO and bare GO with 20 cycles repetition of (5D + R) process was found to be 793.8 μA and 3482.8 μA. Our results showed that the electrical conductivity of bare GO coated conductive cotton yarn increased by approximately four orders of magnitude with the increase in the dipping cycle of (5D+R) process.

Properties of CF/PA6 friction spun hybrid yarns for textile reinforced thermoplastic composites

Science.gov (United States)

Hasan, MMB; Nitsche, S.; Abdkader, A.; Cherif, Ch

2017-10-01

Due to their excellent strength, rigidity and damping properties as well as low weight, carbon fibre reinforced composites (CFRC) are widely being used for load bearing structures. On the other hand, with an increased demand und usage of CFRCs, effective methods to re-use waste carbon fibre (CF) materials, which are recoverable either from the process scraps or from the end-of-life components are attracting increased attention. In this paper, hybrid yarns consisting of staple CF and polyamide 6 (PA 6) are manufactured on a DREF-3000 friction spinning machine with various machine parameters such as spinning drum speed and suction air pressure. The relationship between different textile physical properties of the hybrid yarns, such as tensile strength and elongation with different spinning parameters and CF content of hybrid yarn is investigated. Furthermore, the tensile properties of uni-directional (UD) composites manufactured from the developed hybrid yarn shows 80% of the UD composite strength made from CF filament yarn.

Properties and performance of flax yarn/thermoplastic polyester composites

DEFF Research Database (Denmark)

Madsen, Bo; Mehmood, Shahid

2012-01-01

Aiming at demonstrating the potential of unidirectional natural fiber-reinforced thermoplastic composites in structural applications, textile flax yarn/thermoplastic polyester composites with variable fiber volume fractions have been manufactured by a filament-winding process followed by a vacuum......-assisted compression molding process. The microstructure of the composites shows that the flax fiber yarns are well impregnated by the polyester matrix, and this supports the measured low porosity content of the composites. The experimental tensile modulus and ultimate tensile stress of the composites in the axial...

Rule-based expert system to establish the linkage between yarn twist factor and end-use.

CSIR Research Space (South Africa)

Dlodlo, N

2009-09-01

Full Text Available of the fibre alignment to axis. The tex twist factor αtex is defined as: where: αtex is the tex twist factor, t = twist expressed in turns/metre (or turns/centimetre), Ti = the effective linear density (count) of the composite yarn expressed in tex... of staple fibre yarns. They can be classed by fibre length (e.g. short and long staple), by spinning system (e.g. ring and rotor), or by yarn construction (e.g. single, plied, cabled, multiple and fancy). Ring-spun yarns are produced on 1000/itex Tt=α m...

CUSTOMER DRIVEN QUALITY IMPROVEMENT OF JUTE YARN USING AHP BASED QFD: A CASE STUD

Directory of Open Access Journals (Sweden)

Taposh Kumar Kapuria

2018-03-01

Full Text Available The ready-made garment (RMG industries in Bangladesh have become very competitive to cope with the competitors. The performance of this sector has attracted many countries to invest their money safely here and also earns foreign currency by exporting different materials like jute yarn. Jute yarn is a spun material which is prepared to use for weaving, knitting, sewing threads, carpets, carrying bags etc. In fiscal year 2015-16, according to data from Bangladesh's Export Promotion Bureau (EPB, Bangladesh has earned $559 million by exporting jute yarn and twine. To meet the growing demand of jute yarn worldwide, Bangladesh still has lots of possibilities to earn huge amount of foreign currency by improving the quality. It's a persistent need for Bangladeshi local jute yarn manufacturers to come forward, seek possibilities for improving quality, and fulfill the worldwide demand. The paper focuses on the application of AHP based QFD approach on a manufacturing company to improve its quality of product & improving the level of customer satisfaction. The paper shows how customer requirements can be identified and used them to prioritize the design requirements for improving quality of jute yarn. Here, AHP is integrated into house of quality (HOQ that can be guide for overcoming the pitfalls of traditional QFD.

Psychophysiological response in parachute jumps, the effect of experience and type of jump.

Science.gov (United States)

Clemente-Suárez, Vicente Javier; Robles-Pérez, José Juan; Fernández-Lucas, Jesús

2017-10-01

We aimed to analyse the effect of experience and type of parachute jump on the psychophysiological responses of jumpers. We analysed blood oxygen saturation, heart rate, blood glucose, lactate and creatinkinase, leg strength, isometric hand strength, cortical arousal, specific fine motor skills, self-confidence and cognition, and somatic and state anxiety, before and after four different parachute jumps: a sport parachute jump, a manual tactical parachute jump, tandem pilots, and tandem passengers. Independently of the parachute jump, the psychophysiological responses of experienced paratroopers were not affected by the jumps, except for an increase in anaerobic metabolism. Novice parachute jumpers presented a higher psychophysiological stress response than the experienced jumpers, together with a large anticipatory anxiety response before the jump; however, this decreased after the jump, although the high physiological activation was maintained. This information could be used by civil and military paratroopers' instructors to improve their training programmes. Copyright © 2017 Elsevier Inc. All rights reserved.

Flight test of a spin parachute for use with a Super Arcas sounding rocket

Science.gov (United States)

Silbert, M. N.

1975-01-01

The development and flight testing of a specially configured 16.6 ft Disc Band Gap (DBG) Spin Parachute is discussed. The parachute is integrated with a modified Super Arcas launch vehicle. Total payload weight was 17.6 lbs including the Spin Parachute and a scientific payload, and lift-off weight was 100.3 lbs. The Super Arcas vehicle was despun from 18.4 cps. After payload separation at 244,170 ft the Spin Parachute and its payload attained a maximum spin rate of 2.4 cps. Total suspended weight of the Spin Parachute and its payload was 14.64 lbs.

Study of parachute inflation process using fluid–structure interaction method

Directory of Open Access Journals (Sweden)

Yu Li

2014-04-01

Full Text Available A direct numerical modeling method for parachute is proposed firstly, and a model for the star-shaped folded parachute with detailed structures is established. The simplified arbitrary Lagrangian–Eulerian fluid–structure interaction (SALE/FSI method is used to simulate the inflation process of a folded parachute, and the flow field calculation is mainly based on operator splitting technique. By using this method, the dynamic variations of related parameters such as flow field and structure are obtained, and the load jump appearing at the end of initial inflation stage is captured. Numerical results including opening load, drag characteristics, swinging angle, etc. are well consistent with wind tunnel tests. In addition, this coupled method can get more space–time detailed information such as geometry shape, structure, motion, and flow field. Compared with previous inflation time method, this method is a completely theoretical analysis approach without relying on empirical coefficients, which can provide a reference for material selection, performance optimization during parachute design.

Stiffness and Poisson ratio in longitudinal compression of fiber yarns in meso-FE modelling of composite reinforcement forming

Science.gov (United States)

Wang, D.; Naouar, N.; Vidal-Salle, E.; Boisse, P.

2018-05-01

In meso-scale finite element modeling, the yarns of the reinforcement are considered to be solids made of a continuous material in contact with their neighbors. The present paper consider the mechanical behavior of these yarns that can happen for some loadings of the reinforcement. The yarns present a specific mechanical behavior when under longitudinal compression because they are made up of a large number of fibers, Local buckling of the fibers causes the compressive stiffness of the continuous material representing the yarn to be much weaker than when under tension. In addition, longitudinal compression causes an important transverse expansion. It is shown that the transverse expansion can be depicted by a Poisson ratio that remained roughly constant when the yarn length and the compression strain varied. Buckling of the fibers significantly increases the transverse dimensions of the yarn which leads to a large Poisson ratio (up to 12 for a yarn analyzed in the present study). Meso-scale finite element simulations of reinforcements with binder yarns submitted to longitudinal compression showed that these improvements led to results in good agreement with micro-CT analyses.

A linear dynamic model for rotor-spun composite yarn spinning process

International Nuclear Information System (INIS)

Yang, R H; Wang, S Y

2008-01-01

A linear dynamic model is established for the stable rotor-spun composite yarn spinning process. Approximate oscillating frequencies in the vertical and horizontal directions are obtained. By suitable choice of certain processing parameters, the mixture construction after the convergent point can be optimally matched. The presented study is expected to provide a general pathway to understand the motion of the rotor-spun composite yarn spinning process

The influence of parachute-resisted sprinting on running mechanics in collegiate track athletes.

Science.gov (United States)

Paulson, Sally; Braun, William A

2011-06-01

The influence of parachute-resisted sprinting on running mechanics in collegiate track athletes. The aim of this investigation was to compare the acute effects of parachute-resisted (PR) sprinting on selected kinematic variables. Twelve collegiate sprinters (mean age 19.58 ± 1.44 years, mass 69.32 ± 14.38 kg, height 1.71 ± 9.86 m) ran a 40-yd dash under 2 conditions: PR sprint and sprint without a parachute (NC) that were recorded on a video computer system (60 Hz). Sagittal plane kinematics of the right side of the body was digitized to calculate joint angles at initial ground contact (IGC) and end ground contact (EGC), ground contact (GC) time, stride rate (SR), stride length (SL), and the times of the 40-yd dashes. The NC 40-yd dash time was significantly faster than the PR trial (p 0.05). This study suggests that PR sprinting does not acutely affect GC time, SR, SL and upper extremity or lower extremity joint angles during weight acceptance (IGC) in collegiate sprinters. However, PR sprinting increased shoulder flexion by 23.5% at push-off and decreased speed by 4.4%. While sprinting with the parachute, the athlete's movement patterns resembled their mechanics during the unloaded condition. This indicates the external load caused by PR did not substantially overload the runner, and only caused a minor change in the shoulder during push-off. This sports-specific training apparatus may provide coaches with another method for training athletes in a sports-specific manner without causing acute changes to running mechanics.

A display module implemented by the fast high-temperatue response of carbon nanotube thin yarns.

Science.gov (United States)

Wei, Yang; Liu, Peng; Jiang, Kaili; Fan, Shoushan

2012-05-09

Suspending superaligned multiwalled carbon nanotube (MWCNT) films were processed into CNT thin yarns, about 1 μm in diameter, by laser cutting and an ethanol atomization bath treatment. The fast high-temperature response under a vacuum was revealed by monitoring the incandescent light with a photo diode. The thin yarns can be electrically heated up to 2170 K in 0.79 mS, and the succeeding cool-down time is 0.36 mS. The fast response is attributed to the ultrasmall mass of the independent single yarn, large radiation coefficient, and improved thermal conductance through the two cool ends. The millisecond response time makes it possible to use the visible hot thin yarns as light-emitting elements of an incandescent display. A fully sealed display with 16 × 16 matrix was successfully fabricated using screen-printed thick electrodes and CNT thin yarns. It can display rolling characters with a low power consumption. More applications can be further developed based on the addressable CNT thermal arrays.

Study on the Filament Yarns Spreading Techniques and Assessment Methods of the Electronic Fiberglass Fabric

Science.gov (United States)

Wang, Xi; Chen, Shouhui; Zheng, Tianyong; Ning, Xiangchun; Dai, Yifei

2018-03-01

The filament yarns spreading techniques of electronic fiberglass fabric were developed in the past few years in order to meet the requirements of the development of electronic industry. Copper clad laminate (CCL) requires that the warp and weft yarns of the fabric could be spread out of apart and formed flat. The penetration performance of resin could be improved due to the filament yarns spreading techniques of electronic fiberglass fabric, the same as peeling strength of CCL and drilling performance of printed circuit board (PCB). This paper shows the filament yarns spreading techniques of electronic fiberglass fabric from several aspects, such as methods and functions, also with the assessment methods of their effects.

Piezoresistive effect of the carbon nanotube yarn embedded axially into the 3D braided composite

Science.gov (United States)

Ma, Xin; Cao, Xiaona

2018-06-01

A new method for monitoring 3D braided composite structure health in real time by embedding the carbon nanotube yarn, based on its piezoresistivity, in the composite axially has been designed. The experimental system for piezoresistive effect detection of the carbon nanotube yarn in the 3D braided composite was built, and the sensing characteristics has been analyzed for further research. Compared with other structural health monitoring methods, the monitoring technique with carbon nanotubes yarns is more suitable for internal damage detection immediately, in addition the strength of the composite can be increased by embedding carbon nanotubes yarns. This method can also be used for strain sensing, the development of intelligent materials and structure systems.

CREASING BEHAVIOR OF SOME WOVEN MATERIALS MADE FROM COMBED YARNS TYPE

OpenAIRE

HRISTIAN Liliana; BORDEIANU Demetra Lacramioara; OSTAFE Maria Magdalena; BŐHM-RÉVÉSZ Gabriela

2017-01-01

The paper analyses the behavior to creasing of some woven materials made from yarns type wool used for ready-made clothes. Factors like fibrous composition, properties of constituent fibers, wovens structure parameters, mechanical properties of warp and weft yarns and finishing treatments that influenced the recovery capacity from crease/folding were investigated experimentally through several tests which revealed their importance in the process. The creasing of woven materials made from c...

Determination of Parachute Joint Factors using Seam and Joint Testing

Science.gov (United States)

Mollmann, Catherine

2015-01-01

This paper details the methodology for determining the joint factor for all parachute components. This method has been successfully implemented on the Capsule Parachute Assembly System (CPAS) for the NASA Orion crew module for use in determining the margin of safety for each component under peak loads. Also discussed are concepts behind the joint factor and what drives the loss of material strength at joints. The joint factor is defined as a "loss in joint strength...relative to the basic material strength" that occurs when "textiles are connected to each other or to metals." During the CPAS engineering development phase, a conservative joint factor of 0.80 was assumed for each parachute component. In order to refine this factor and eliminate excess conservatism, a seam and joint testing program was implemented as part of the structural validation. This method split each of the parachute structural joints into discrete tensile tests designed to duplicate the loading of each joint. Breaking strength data collected from destructive pull testing was then used to calculate the joint factor in the form of an efficiency. Joint efficiency is the percentage of the base material strength that remains after degradation due to sewing or interaction with other components; it is used interchangeably with joint factor in this paper. Parachute materials vary in type-mainly cord, tape, webbing, and cloth -which require different test fixtures and joint sample construction methods. This paper defines guidelines for designing and testing samples based on materials and test goals. Using the test methodology and analysis approach detailed in this paper, the minimum joint factor for each parachute component can be formulated. The joint factors can then be used to calculate the design factor and margin of safety for that component, a critical part of the design verification process.

Magnetoreresistance of carbon nanotube-polypyrrole composite yarns

Science.gov (United States)

Ghanbari, R.; Ghorbani, S. R.; Arabi, H.; Foroughi, J.

2018-05-01

Three types of samples, carbon nanotube yarn and carbon nanotube-polypyrrole composite yarns had been investigated by measurement of the electrical conductivity as a function of temperature and magnetic field. The conductivity was well explained by 3D Mott variable range hopping (VRH) law at T < 100 K. Both positive and negative magnetoresistance (MR) were observed by increasing magnetic field. The MR data were analyzed based a theoretical model. A quadratic positive and negative MR was observed for three samples. It was found that the localization length decreases with applied magnetic field while the density of states increases. The increasing of the density of states induces increasing the number of available energy states for hopping. Thus the electron hopping probability increases in between sites with the shorter distance that results to small the average hopping length.

Cost-Benefit and Performance of Handmade Carpets Produced with Wool, Untreated and Chemical Treated Jute Pile Yarns

Science.gov (United States)

Gupta, Shravan Kumar; Goswami, Kamal Kanti

2018-03-01

Jute is a natural fibre which is used to make different type of products due to low cost, easy availability and eco-friendliness. However, the stiffness and harshness of jute fibre affect the use of jute in many products like pile yarns in hand knotted carpets. In this research, a study has been done on the application of jute pile yarns in Persian hand knotted carpet. Three types of commercial yarns (wool, untreated jute and woollenized jute) as well as three types of chemical treated jute yarns (hydrogen peroxide bleached, softened bleached and woollenized yarns) have been applied as pile yarns in Persian hand knotted carpets. Cost-benefit analysis of hand knotted carpets shows that manufacturing cost of wool carpet is lower than others. The contribution of manpower charges is higher than material cost during carpet manufacturing. Hand knotted carpet shows the lowest pile abrasion loss and highest compression recovery when wool is used as pile. Wool hand knotted carpet shows higher compression than untreated and treated jute carpets.

Tensile Properties of Single Jersey and 1×1 Rib Knitted Fabrics Made from 100% Cotton and Cotton/Lycra Yarns

Directory of Open Access Journals (Sweden)

Dereje Berihun Sitotaw

2017-01-01

Full Text Available The tensile properties such as tensile strength which is measured as breaking force in Newton (N and elongation percent (% at break of single jersey and 1×1 rib (knitted with full needles knitted fabrics made from 100% cotton and cotton/Lycra yarns (5% Lycra yarn content in 95% combed cotton yarn are investigated in this research. The sample fabrics are conditioned for 24 hours at 20±1°C temperature and 65±2% relative humidity before testing. Ten specimens (five for lengthwise and five for widthwise have been taken from each of the two knitted structures, those made from 100% cotton and cotton/Lycra (at 95/5 percent ratio blend yarns. According to the discussion and as found from the investigations, the tensile properties of single jersey and 1×1 rib knitted fabrics made from 100% cotton and cotton/Lycra yarns are significantly different from each other and both of the knitted fabrics have high elongation percent at break with cotton/Lycra blend yarns as compared to 100% cotton yarn. Knitted fabrics made from cotton/Lycra blended yarn have low breaking force and high elongation percent at break relative to knitted fabrics made from 100% cotton yarns.

The Processing Design of Jute Spun Yarn/PLA Braided Composite by Pultrusion Molding

Directory of Open Access Journals (Sweden)

Anin Memon

2013-01-01

Full Text Available Prevalently, the light has been shed on the green composite from the viewpoint of environmental protection. Jute fibers are natural fibers superior due to light weight, low cost, and being environmentally friendly corresponding to the green composite materials. Meticulously, fibers of polylactic acid (PLA thermoplastic biopolymer were used as the resin fibers. In this study, the fabrication of tubular jute spun yarn/PLA braided composite by pultrusion molding was presented. The intermediate materials were prepared by commingled technique. The braiding technique manufactured preform which had jute fiber diagonally oriented at certain angles with the glass fiber inserted into the braiding yarns along the longitudinal direction. The braided preforms were pulled through a heated die where the consolidation flow took place due to reduced matrix viscosity and pressure. The pultrusion experiments were done with jute/PLA commingled yarns and combined with glass fiber yarns to fabricate the tubular composite. Impregnation quality was evaluated by microscope observation of the pultruded cross-sections. The flexural mechanical properties of the pultruded were measured by four-point bending test.

Parachuting behavior and predation by ants in the nettle caterpillar, Scopelodes contracta.

Science.gov (United States)

Yamazaki, Kazuo

2010-01-01

This paper documents the bizarre descending behavior from the tree crown to the ground of the larvae of the moth, Scopelodes contracta Walker (Lepidoptera: Limacodidae) and the interaction of the larva with predatory ants. S. contracta larvae infest leaves of many tree species in urban areas and orchards in Japan. Mature larvae and leaves without basal leaf parts were found under trees of four species infested with S. contracta larvae in Osaka, Japan. Individual larvae riding on leaves were observed falling from tree crowns to the ground. Many S. contracta cocoons were found in the soil below the trees two weeks after the observed parachuting. These observations indicate that S. contracta larvae parachuted to the ground where they spin their cocoons in the soil. When a larva that had just parachuted down was returned to an arboreal twig, the larva repeated the parachuting behavior. This parachuting behavior appears to be adaptive, because larvae can descend to the ground safely and with low energy cost. Worker ants of Tetramorium tsushimae Emery (Hymenoptera: Formicidae) and Pristomyrmex punctatus Mayr (Hymenoptera: Formicidae) occasionally attacked larvae on the ground before they had a chance to burrow in the soil.

Enhancement of chondrogenic differentiation of rabbit mesenchymal stem cells by oriented nanofiber yarn-collagen type I/hyaluronate hybrid

International Nuclear Information System (INIS)

Zheng, Xianyou; Wang, Wei; Liu, Shen; Wu, Jinglei; Li, Fengfeng; Cao, Lei; Liu, Xu-dong; Mo, Xiumei; Fan, Cunyi

2016-01-01

Cartilage defects cause joint pain and loss of mobility. It is crucial to induce the chondrogenic differentiation of bone marrow mesenchymal stem cells (BMSCs) by both biological and structural signals in cartilage tissue engineering. Sponge-like scaffolds fabricated using native cartilage extracellular matrix components can induce the BMSC differentiation by biological signals and limited structural signals. In this study, an oriented poly(L-lactic acid)-co-poly(ε-caprolactone) P(LLA-CL)/collagen type I (Col-I) nanofiber yarn mesh, fabricated by dynamic liquid electrospinning served as a skeleton for a freeze-dried Col-I/hyaluronate (HA) chondral phase (SPONGE) containing both structural and biological signals to guide BMSC chondrogenic differentiation. In vitro results show that the Yarn Col-I/HA hybrid scaffold (Yarn-CH) promotes orientation, adhesion and proliferation of BMSCs better than SPONGE. Furthermore, BMSCs seeded on the Yarn-CH scaffold demonstrated a large increase in the glycosaminoglycan content and expression of collagen type II following a 21-day culture. - Highlights: • An oriented yarn was used as the skeleton of the sponge-like scaffold. • Both structural and biological signals were given for BMSC chondrogenic differentiation. • Yarn-CH promotes orientation and chondrogenesis differentiation of BMSCs. • Yarn-CH reproduces the superficial zone of the cartilage.

Analysis of Different Breed of Protein Fibres and their Influence on Mechanical Properties of Woollen Blend Yarns

Directory of Open Access Journals (Sweden)

Audronė RAGAIŠIENĖ

2016-09-01

Full Text Available The aim of this research was to analyse possibilities of making different woollen blend yarns with sheep’s wool and dog’s hair fibers and to investigate geometrical and mechanical properties of these yarns. In this paper sheep’s wool and dogs’ hair fibers were compared one with other in different geometrical (fibre surface, length, diameter, linear density and mechanical (breaking tenacity, elongation at break, breaking toughness properties. It was estimated that the sheep’s and the dog’s fibers are visually very different, they have various types of scales, also most of the dog’s hair have channels inside them. On the next stage of this work the woollen blend yarns were made by mixing the wool of German Blackface sheep with different breed (English Spaniel, Poodle, Yorkshire Terrier dogs’ hair 15 %, 25 % and 35 %. After evaluating the linear density and mechanical properties of woollen blend yarns, it was estimated that influence of fiber composition in the yarns on these properties is different. Different values of the investigated properties are mostly influenced by spinning system of these yarns. The condenser spinning system affects inequality and unpredictable properties of woollen blend yarns. Also, obtained results depend on the breed of protein fibers, hairy surface, hollow structure and bending rigidity of fiber, the technological process or even compatibility of used devices.DOI: http://dx.doi.org/10.5755/j01.ms.22.3.8974

In situ polymerization of vinyl monomers in polyester yarns

International Nuclear Information System (INIS)

Avny, Y.; Rebenfeld, L.; Weigmann, H.D.

1978-01-01

The effects of a pretreatment of polyester (PET) yarns with a strongly interacting solvent such as dimethylformamide (DMF) on vinyl monomer incorporation were investigated. When the DMF pretreatment is carried out at high temperatures (above 120 0 C), the swollen PET structure is stabilized by solvent-induced secondary crystallization. This substrate is highly suitable for the incorporation of vinyl monomers. In situ polymerization of vinyl monomers in DMF-treated PET was investigated using chemical and γ-irradiation polymerization techniques, both in the presence and in the absence of excess monomer outside the PET fibers. When polymerization was carried out in a system in which a constant supply of free radicals was available from the outside of the PET fibers, lower initiator concentrations and smaller γ-irradiation doses were necessary. These results are attributed to a low efficiency of the initiator inside the PET fiber due to mobility restrictions. Water uptake and moisture regain of PET yarns containing poly(hydroxyethyl methacrylate) and poly(acrylic acid) were also investigated. When most of the vinyl polymer was inside the PET fiber, water absorption was limited. The changes in mechanical properties of the PET yarns resulting from the DMF pretreatment were partially reversed by in situ polymerization of vinyl monomers

A Survey of Parachute Ankle Brace Breakages

National Research Council Canada - National Science Library

Knapik, Joseph J; Spiess, Anita; Darakjy, Salima; Grier, Tyson; Manning, Fred; Livingston, Elaine; Swedler, David; Amoroso, Paul; Jones, Bruce H

2008-01-01

...) of the Defense Safety Oversight Council (DSOC) to evaluate the parachute ankle brace (PAB). Information provided by the questionnaire identified potential injury risk factors and comments on the PAB...

Effect of Parachute Jump in the Psychophysiological Response of Soldiers in Urban Combat.

Science.gov (United States)

Sánchez-Molina, Joaquín; Robles-Pérez, José J; Clemente-Suárez, Vicente J

2017-06-01

The study of organic and psychological response during combat situations has been poorly reported despite its importance for soldiers training and specific instruction, so it was proposed as aim of the present investigation to analyze the effect of a tactical parachute simulated jump in psycho-physiological response of paratroopers' warfighters during an urban combat simulation. 19 male paratroopers (31.9 ± 6.2 year old; 173.6 ± 5.3 cm; 73.8 ± 8.3 Kg) of the Spanish Army were divided in two groups: parachute jump group (n:11) that conducted a simulated parachute jump and a urban combat maneuver and a non-parachute jump group (n:8) that only conducted an urban combat maneuver. We analyzed before and after the maneuver the rated perceived exertion, legs strength manifestation, blood lactate, cortical activation, heart rate variability, blood oxygen saturation and pressure, skin temperature, fine motor skills, and anxiety state. A tactical parachute simulated jump prior to an urban combat maneuver produce significantly (p jump situation in professional Army paratroopers. Independently of the parachute jump, an urban combat maneuver produces a significant increase in rated perceived exertion, blood lactate, heart rate, legs strength, sympathetic modulation and anxiety response as well as a significant decrease in blood oxygen saturation and parasympathetic modulation.

Prolactin, thyrotropin, and growth hormone release during stress associated with parachute jumping.

Science.gov (United States)

Noel, G L; Dimond, R C; Earll, J M; Frantz, A G

1976-05-01

Prolactin, growth hormone, and thyrotropin (TSH) release during the stress of parachute jumping has been evaluated in 14 male subjects. Subjects were studied at several times before and immediately after their first military parachute jump. All three hormones had risen significantly 1 to 14 min after the jump, compared to mean levels measured immediately beforehand. Earlier studies of physical exercise by ourselves and others would suggest that emotional stress played a role in producing changes of this magnitude. We conclude that prolactin, TSH, and growth hormone are released in physiologically significant amounts in association with the stress of parachute jumping.

CREASING BEHAVIOR OF SOME WOVEN MATERIALS MADE FROM COMBED YARNS TYPE

Directory of Open Access Journals (Sweden)

HRISTIAN Liliana

2017-05-01

Full Text Available The paper analyses the behavior to creasing of some woven materials made from yarns type wool used for ready-made clothes. Factors like fibrous composition, properties of constituent fibers, wovens structure parameters, mechanical properties of warp and weft yarns and finishing treatments that influenced the recovery capacity from crease/folding were investigated experimentally through several tests which revealed their importance in the process. The creasing of woven materials made from combed yarns type wool used for ready-clothes is an undesired deformation effect with temporary or permanent character, which is caused by a composed strain of bending and compression during utilization, processing or maintenance. It is manifested by the appearance of wrinkles, folds or stripes on the surface of wovens materials, thus diminishing their qualitative appearance and also their practical value. Creasing is the result of irreversible changes created through the reciprocal sliding of structural fiber components when exposed to a bending strain. Creasing is specific to oriented structures with high crystallinity (cellulosic fibers. The sliding appears because of hydrogen bond breaking which can, however, reform easy in other positions conferring a permanent character to creasing.Functional apparel will be subjected to a wide range of end uses such that a garment will be affected by intern (fibres, yarn fineness warp/weft, fabric density, thickness, fabric count and external factors (external environment - exposure to sunlight, wind, rain, cold weather conditions, fabric/human body interaction. These factors affect the performance and behaviour of functional.

Study of the Contact Resistance of Interlaced Stainless Steel Yarns Embedded in Hybrid Woven Fabrics

Directory of Open Access Journals (Sweden)

Vasile Simona

2017-06-01

Full Text Available The contact resistance of two interlacing electro-conductive yarns embedded in a hybrid woven fabric will constitute a problem for electro-conductive textiles under certain circumstances. A high contact resistance can induce hotspots, while a variable contact resistance may cause malfunctioning of the components that are interconnected by the electro-conductive yarns. Moreover, the contact robustness should be preserved over time and various treatments such as washing or abrading should not alter the functioning of the electro-conductive textiles. The electrical resistance developed in the contact point of two interlacing electro-conductive yarns is the result of various factors. The influence of diameter of the electro-conductive stainless steel yarns, the weave pattern, the weft density, and the abrasion on the contact resistance was investigated. Hybrid polyester fabrics were produced according to the design of experiments (DoE and statistical models were found that describe the variation of the contact resistance with the selected input parameters. It was concluded that the diameter of the stainless steel warp and weft yarns has a statistically significant influence on the contact resistance regardless of the weave. Weft density had a significant influence on the contact resistance but only in case of the twill fabrics. Abrasion led to an increase in contact resistance regardless of the weave pattern and the type of stainless steel yarn that was used. Finally, a combination of parameters that leads to plain and twill fabrics with low contact resistance and robust contacts is recommended.

Estimates for the Aerodynamic Coefficients of Ringsail and Disk-Gap-Band Parachutes Operating on Mars

Science.gov (United States)

Cruz, Juan R.; Snyder, Miranda L.

2017-01-01

Models are presented for the aerodynamic coefficients of Supersonic Ringsail and Disk-Gap-Band parachutes as functions of total porosity, Lambda(sub t), Mach number, M, and total angle of attack, Alpha(sub t) (when necessary). The source aerodynamic coefficients data used for creating these models were obtained from a wind tunnel test of subscale parachutes. In this wind tunnel test, subscale parachutes of both parachute types were fabricated from two different fabrics with very different permeabilities. By varying the fabric permeability, while maintaining the parachute geometry constant, it was possible to vary Alpha(sub t). The fabric permeability test data necessary for the calculation of Alpha(sub t) were obtained from samples of the same fabrics used to fabricate the subscale parachutes. Although the models for the aerodynamic coefficients are simple polynomial functions of Alpha(sub t) and M, they are capable of producing good reproductions of the source data. The (Alpha(sub t), M) domains over which these models are applicable are clearly defined. The models are applicable to flight operations on Mars.

Multifunctional smart composites with integrated carbon nanotube yarn and sheet

Science.gov (United States)

Chauhan, Devika; Hou, Guangfeng; Ng, Vianessa; Chaudhary, Sumeet; Paine, Michael; Moinuddin, Khwaja; Rabiee, Massoud; Cahay, Marc; Lalley, Nicholas; Shanov, Vesselin; Mast, David; Liu, Yijun; Yin, Zhangzhang; Song, Yi; Schulz, Mark

2017-04-01

Multifunctional smart composites (MSCs) are materials that combine the good electrical and thermal conductivity, high tensile and shear strength, good impact toughness, and high stiffness properties of metals; the light weight and corrosion resistance properties of composites; and the sensing or actuation properties of smart materials. The basic concept for MSCs was first conceived by Daniel Inman and others about 25 years ago. Current laminated carbon and glass fiber polymeric composite materials have high tensile strength and are light in weight, but they still lack good electrical and thermal conductivity, and they are sensitive to delamination. Carbon nanotube yarn and sheets are lightweight, electrically and thermally conductive materials that can be integrated into laminated composite materials to form MSCs. This paper describes the manufacturing of high quality carbon nanotube yarn and sheet used to form MSCs, and integrating the nanotube yarn and sheet into composites at low volume fractions. Various up and coming technical applications of MSCs are discussed including composite toughening for impact and delamination resistance; structural health monitoring; and structural power conduction. The global carbon nanotube overall market size is estimated to grow from 2 Billion in 2015 to 5 Billion by 2020 at a CAGR of 20%. Nanotube yarn and sheet products are predicted to be used in aircraft, wind machines, automobiles, electric machines, textiles, acoustic attenuators, light absorption, electrical wire, sporting equipment, tires, athletic apparel, thermoelectric devices, biomedical devices, lightweight transformers, and electromagnets. In the future, due to the high maximum current density of nanotube conductors, nanotube electromagnetic devices may also become competitive with traditional smart materials in terms of power density.

Parachute-Payload System Flight Dynamics and Trajectory Simulation

Directory of Open Access Journals (Sweden)

Giorgio Guglieri

2012-01-01

Full Text Available The work traces a general procedure for the design of a flight simulation tool still representative of the major flight physics of a parachute-payload system along decelerated trajectories. An example of limited complexity simulation models for a payload decelerated by one or more parachutes is given, including details and implementation features usually omitted as the focus of the research in this field is typically on the investigation of mission design issues, rather than addressing general implementation guidelines for the development of a reconfigurable simulation tool. The dynamics of the system are modeled through a simple multibody model that represents the expected behavior of an entry vehicle during the terminal deceleration phase. The simulators are designed according to a comprehensive vision that enforces the simplification of the coupling mechanism between the payload and the parachute, with an adequate level of physical insight still available. The results presented for a realistic case study define the sensitivity of the simulation outputs to the functional complexity of the mathematical model. Far from being an absolute address for the software designer, this paper tries to contribute to the area of interest with some technical considerations and clarifications.

Yarn-dyed fabric defect classification based on convolutional neural network

Science.gov (United States)

Jing, Junfeng; Dong, Amei; Li, Pengfei; Zhang, Kaibing

2017-09-01

Considering that manual inspection of the yarn-dyed fabric can be time consuming and inefficient, we propose a yarn-dyed fabric defect classification method by using a convolutional neural network (CNN) based on a modified AlexNet. CNN shows powerful ability in performing feature extraction and fusion by simulating the learning mechanism of human brain. The local response normalization layers in AlexNet are replaced by the batch normalization layers, which can enhance both the computational efficiency and classification accuracy. In the training process of the network, the characteristics of the defect are extracted step by step and the essential features of the image can be obtained from the fusion of the edge details with several convolution operations. Then the max-pooling layers, the dropout layers, and the fully connected layers are employed in the classification model to reduce the computation cost and extract more precise features of the defective fabric. Finally, the results of the defect classification are predicted by the softmax function. The experimental results show promising performance with an acceptable average classification rate and strong robustness on yarn-dyed fabric defect classification.

Dynamic Mesh CFD Simulations of Orion Parachute Pendulum Motion During Atmospheric Entry

Science.gov (United States)

Halstrom, Logan D.; Schwing, Alan M.; Robinson, Stephen K.

2016-01-01

This paper demonstrates the usage of computational fluid dynamics to study the effects of pendulum motion dynamics of the NASAs Orion Multi-Purpose Crew Vehicle parachute system on the stability of the vehicles atmospheric entry and decent. Significant computational fluid dynamics testing has already been performed at NASAs Johnson Space Center, but this study sought to investigate the effect of bulk motion of the parachute, such as pitching, on the induced aerodynamic forces. Simulations were performed with a moving grid geometry oscillating according to the parameters observed in flight tests. As with the previous simulations, OVERFLOW computational fluid dynamics tool is used with the assumption of rigid, non-permeable geometry. Comparison to parachute wind tunnel tests is included for a preliminary validation of the dynamic mesh model. Results show qualitative differences in the flow fields of the static and dynamic simulations and quantitative differences in the induced aerodynamic forces, suggesting that dynamic mesh modeling of the parachute pendulum motion may uncover additional dynamic effects.

Tensile strength of ramie yarn (spinning by machine)/HDPE thermoplastic matrix composites

International Nuclear Information System (INIS)

Banowati, Lies; Hadi, Bambang K.; Suratman, Rochim; Faza, Aulia

2016-01-01

Technological developments should be trooped to prevent a gap between technology and environmental sustainability, then it needs to be developed “Green technology”. In this research is making of green composites which use natural fiber ramie as reinforcement. Whereas the matrix used was HDPE (High Density Polyethylene) thermoplastic polymer which could be recycled and had a good formability and flexibility. The ramie yarns and fibers for unidirectional (0°) direction respectively were mixed with HDPE powder and processed using hot compression molding. The surface morphology was observed by SEM (Scanning Electrone Microscopy). Results showed that both tensile strength of the ramie fiber/HDPE composites increased in comparison with the ramie yarn (spinning by machine)/HDPE composites. However, the ramie yarn (spinning by machine)/HDPE composites have a good producibility for wider application. Analysis of the test results using the Weibull distribution as approaches to modeling the reliability of the specimens.

Tensile strength of ramie yarn (spinning by machine)/HDPE thermoplastic matrix composites

Energy Technology Data Exchange (ETDEWEB)

Banowati, Lies, E-mail: liesbano@gmail.com; Hadi, Bambang K., E-mail: bkhadi@ae.itb.ac.id; Suratman, Rochim, E-mail: rochim@material.itb.ac.id; Faza, Aulia [Faculty of Mechanical and Aerospace Engineering, Bandung Institute of Technology, Indonesia Jl. Ganesha 10, Bandung (Indonesia)

2016-03-29

Technological developments should be trooped to prevent a gap between technology and environmental sustainability, then it needs to be developed “Green technology”. In this research is making of green composites which use natural fiber ramie as reinforcement. Whereas the matrix used was HDPE (High Density Polyethylene) thermoplastic polymer which could be recycled and had a good formability and flexibility. The ramie yarns and fibers for unidirectional (0°) direction respectively were mixed with HDPE powder and processed using hot compression molding. The surface morphology was observed by SEM (Scanning Electrone Microscopy). Results showed that both tensile strength of the ramie fiber/HDPE composites increased in comparison with the ramie yarn (spinning by machine)/HDPE composites. However, the ramie yarn (spinning by machine)/HDPE composites have a good producibility for wider application. Analysis of the test results using the Weibull distribution as approaches to modeling the reliability of the specimens.

The further development and evaluation of an automatic dismantler of short staple ring-spun yarns

CSIR Research Space (South Africa)

Fassihi, A

2014-07-01

Full Text Available Information System (AFIS) single fiber length tests, the fibers from automatically dismantled ring-spun cotton yarns are very similar in their properties to those dismantled by hand (manually). It was also found that, at a speed of 2 m/min, the yarn dismantler...

Modeling and experiments on ballistic impact into UHMWPE yarns using flat and saddle-nosed projectiles

NARCIS (Netherlands)

Phoenix, S.L.; Heisserer, U.; Werff, H. van der; Jagt-Deutekom , M.J. van der

2017-01-01

Yarn shooting experiments were conducted to determine the ballistically-relevant, Young’s modulus and tensile strength of ultra-high molecular weight polyethylene (UHMWPE) fiber. Target specimens were Dyneema® SK76 yarns (1760 dtex), twisted to 40 turns/m, and initially tensioned to stresses ranging

Electron Beam Irradiated Intercalated CNT Yarns For Aerospace Applications

Science.gov (United States)

Waters, Deborah L.; Gaier, James R.; Williams, Tiffany S.; Lopez Calero, Johnny E.; Ramirez, Christopher; Meador, Michael A.

2015-01-01

Multi-walled CNT yarns have been experimentally and commercially created to yield lightweight, high conductivity fibers with good tensile properties for application as electrical wiring and multifunctional tendons. Multifunctional tendons are needed as the cable structures in tensegrity robots for use in planetary exploration. These lightweight robust tendons can provide mechanical strength for movement of the robot in addition to power distribution and data transmission. In aerospace vehicles, such as Orion, electrical wiring and harnessing mass can approach half of the avionics mass. Use of CNT yarns as electrical power and data cables could reduce mass of the wiring by thirty to seventy percent. These fibers have been intercalated with mixed halogens to increase their specific electrical conductivity to that near copper. This conductivity, combined with the superior strength and fatigue resistance makes it an attractive alternative to copper for wiring and multifunctional tendon applications. Electron beam irradiation has been shown to increase mechanical strength in pristine CNT fibers through increased cross-linking. Both pristine and intercalated CNT yarns have been irradiated using a 5-megavolt electron beam for various durations and the conductivities and tensile properties will be discussed. Structural information obtained using a field emission scanning electron microscope, energy dispersive X-ray spectroscopy (EDS), and Raman spectroscopy will correlate microstructural details with bulk properties.

Multiscale modeling of interwoven Kevlar fibers based on random walk to predict yarn structural response

Science.gov (United States)

Recchia, Stephen

Kevlar is the most common high-end plastic filament yarn used in body armor, tire reinforcement, and wear resistant applications. Kevlar is a trade name for an aramid fiber. These are fibers in which the chain molecules are highly oriented along the fiber axis, so the strength of the chemical bond can be exploited. The bulk material is extruded into filaments that are bound together into yarn, which may be chorded with other materials as in car tires, woven into a fabric, or layered in an epoxy to make composite panels. The high tensile strength to low weight ratio makes this material ideal for designs that decrease weight and inertia, such as automobile tires, body panels, and body armor. For designs that use Kevlar, increasing the strength, or tenacity, to weight ratio would improve performance or reduce cost of all products that are based on this material. This thesis computationally and experimentally investigates the tenacity and stiffness of Kevlar yarns with varying twist ratios. The test boundary conditions were replicated with a geometrically accurate finite element model, resulting in a customized code that can reproduce tortuous filaments in a yarn was developed. The solid model geometry capturing filament tortuosity was implemented through a random walk method of axial geometry creation. A finite element analysis successfully recreated the yarn strength and stiffness dependency observed during the tests. The physics applied in the finite element model was reproduced in an analytical equation that was able to predict the failure strength and strain dependency of twist ratio. The analytical solution can be employed to optimize yarn design for high strength applications.

Textile production in the Bronze Age: an assemblage of splindes or bobbins of yarn from the site of Terlinques (Villena, Alicante

Directory of Open Access Journals (Sweden)

Jover Maestre, Francisco Javier

2001-06-01

Full Text Available The archeological field work on the Bronze Age site of Terlinques (Villena, Alicante has given an exceptional sample of spindles or bobbins of rush fibre of yarn in a room destroyed by a violent fire. A meticulous study of these special objects and their process of analysis and restoration yields new perspectives on knowledge in first stages of textile production during Bronze Age in Eastern Spain.

Los trabajos arqueológicos que se llevan a cabo en el yacimiento de la Edad del Bronce de Terlinques (Villena, Alicante han proporcionado un excepcional conjunto de husos o bobinas de hilo de junco. Éstos se hallaban almacenados en el interior de una habitación destruida por un violento incendio. El detenido estudio de estos singulares objetos y su proceso de análisis y restauración nos permite aproximamos, desde nuevas perspectivas, al conocimiento de la producción textil en las etapas iniciales de la Edad del Bronce en el Levante de la Península Ibérica.

A new experimental setup to characterize the dynamic mechanical behaviour of ballistic yarns

International Nuclear Information System (INIS)

Chevalier, C; Kerisit, C; Faderl, N; Klavzar, A; Boussu, F; Coutellier, D

2016-01-01

Fabrics have been widely used as part of ballistic protections since the 1970s and the development of new ballistic solutions made from fabrics need numerical simulations, in order to predict the performance of the ballistic protection. The performances and the induced mechanisms in ballistic fabrics during an impact depend on the weaving parameters and also on the inner parameters of the yarns used inside these structures. Thus, knowing the dynamic behaviour of yarn is essential to determine the ballistic behaviour of fabrics during an impact. Two major experimental devices exist and are used to test ballistic yarns in a dynamic uniaxial tension. The first one corresponds to the Split Hopkinson Tensile Bars device, which is commonly used to characterize the mechanical properties of materials in uniaxial tension and under high loading. The second one is the transversal impact device. The real conditions of ballistic impact can be realized with this device. Then, this paper deals with a new experimental setup developed in our laboratory and called the ‘tensile impact test for yarn’ (TITY) device. With this device, specific absorbed energy measurements of para-aramid yarns (336 Tex, Twaron ™ , 1000 filaments) have been carried out and revealed that static and dynamic properties of para-aramid are different. (paper)

Factors Affecting Planting Depth and Standing of Rice Seedling in Parachute Rice Transplanting

Science.gov (United States)

Astika, I. W.; Subrata, I. D. M.; Pramuhadi, G.

2018-05-01

Parachute rice transplanting is a simple and practical rice transplanting method. It can be done manually or mechanically, with various possible designs of machines or tools. This research aimed at quantitatively formulating related factors to the planting depth and standing of rice seedling. Parachute seedlings of rice were grown at several sizes of parachute soil bulb sizes. The trays were specially designed with a 3D printer having bulb sizes 7, 8, 9, 10 mm in square sides and 15 mm depth. At seedling ages of 8-12 days after sowing the seedling bulbs were drops into puddled soil. Soil hardness was set at 3 levels of hardness, measured in hardness index using golf ball test. Angle of dropping was set at 3 levels: 0°, 30°and 45° from the vertical axis. The height of droppings was set at 100 cm, 75 cm, and 50 cm. The relationship between bulb size, height of dropping, soil hardness, dropping angle and planting depth was formulated with ANN. Most of input variables did not significantly affect the planting depth, except that hard soil significantly differs from mild soil and soft soil. The dropping also resulted in various positions of the planted seedlings: vertical standing, sloped, and falling. However, at any position of the planted seedlings, the seedlings would recover themselves into normally vertical position. With this result, the design of planting machinery, as well as the manual planting operation, can be made easier.

Effect of the yarn pull-out velocity of shear thickening fluid-impregnated Kevlar fabric on the coefficient of friction

Energy Technology Data Exchange (ETDEWEB)

Aikarami, Sh [Dept. of Mechanical and Aerospace Engineering, Science and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Kordani, N. [Dept. of Mechanical Engineering, University of Mazandaran, Mazandaran (Iran, Islamic Republic of); Sadough, Vanini A. [Dept. of Mechanical Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Amiri, H. [Technical Campus, Tehran South Branch, Islamic Azad University, Tehran(Iran, Islamic Republic of)

2016-08-15

This study explains the yarn pull-out process behavior of woven fabrics in relation to their mechanical properties. Empirical research on the relationship between the yarn pull-out behavior and fabric properties are evaluated, along with a detailed comparison of friction between the fabric fibers in static and dynamic modes. Samples are tested in three modes, namely, neat, dissolved liquid, and silica particle- based Shear thickening fluid (STF)-treated fabric. Accordingly, the presence of STF increases friction between the fabrics and the warp and weft yarns, as well as prevents the displacement of the yarns. Increased friction also leads to an increase in the energy absorption of the yarn pull-out process. In this research, the pull-out test has been performed at three different velocities: 50, 250 and 500 mm/min. Results show that increases in the pull-out velocity increase the pull-out force of the neat and dissolved liquid samples. By contrast, the behavior is completely opposite in the STF-treated sample. Comparing the yarn pull-out values indicates that the STF-treated samples have the highest value, which is approximately three times higher than that of the neat sample.

Effect of the yarn pull-out velocity of shear thickening fluid-impregnated Kevlar fabric on the coefficient of friction

International Nuclear Information System (INIS)

Aikarami, Sh; Kordani, N.; Sadough, Vanini A.; Amiri, H.

2016-01-01

This study explains the yarn pull-out process behavior of woven fabrics in relation to their mechanical properties. Empirical research on the relationship between the yarn pull-out behavior and fabric properties are evaluated, along with a detailed comparison of friction between the fabric fibers in static and dynamic modes. Samples are tested in three modes, namely, neat, dissolved liquid, and silica particle- based Shear thickening fluid (STF)-treated fabric. Accordingly, the presence of STF increases friction between the fabrics and the warp and weft yarns, as well as prevents the displacement of the yarns. Increased friction also leads to an increase in the energy absorption of the yarn pull-out process. In this research, the pull-out test has been performed at three different velocities: 50, 250 and 500 mm/min. Results show that increases in the pull-out velocity increase the pull-out force of the neat and dissolved liquid samples. By contrast, the behavior is completely opposite in the STF-treated sample. Comparing the yarn pull-out values indicates that the STF-treated samples have the highest value, which is approximately three times higher than that of the neat sample

Reconstruction of Orion Engineering Development Unit (EDU) Parachute Inflation Loads

Science.gov (United States)

Ray, Eric S.

2013-01-01

The process of reconstructing inflation loads of Capsule Parachute Assembly System (CPAS) has been updated as the program transitioned to testing Engineering Development Unit (EDU) hardware. The equations used to reduce the test data have been re-derived based on the same physical assumptions made by simulations. Due to instrumentation challenges, individual parachute loads are determined from complementary accelerometer and load cell measurements. Cluster inflations are now simulated by modeling each parachute individually to better represent different inflation times and non-synchronous disreefing. The reconstruction procedure is tailored to either infinite mass or finite mass events based on measurable characteristics from the test data. Inflation parameters are determined from an automated optimization routine to reduce subjectivity. Infinite mass inflation parameters have been re-defined to avoid unrealistic interactions in Monte Carlo simulations. Sample cases demonstrate how best-fit inflation parameters are used to generate simulated drag areas and loads which favorably agree with test data.

Increased Tensile Strength of Carbon Nanotube Yarns and Sheets through Chemical Modification and Electron Beam Irradiation

Science.gov (United States)

Miller, Sandi G.; Williams, Tiffany S.; Baker, James S.; Sola, Francisco; Lebron-Colon, Marisabel; McCorkle, Linda S.; Wilmoth, Nathan G.; Gaier, James; Chen, Michelle; Meador, Michael A.

2014-01-01

The inherent strength of individual carbon nanotubes offers considerable opportunity for the development of advanced, lightweight composite structures. Recent work in the fabrication and application of carbon nanotube (CNT) forms such as yarns and sheets has addressed early nanocomposite limitations with respect to nanotube dispersion and loading; and has pushed the technology toward structural composite applications. However, the high tensile strength of an individual CNT has not directly translated to macro-scale CNT forms where bulk material strength is limited by inter-tube electrostatic attraction and slippage. The focus of this work was to assess post processing of CNT sheet and yarn to improve the macro-scale strength of these material forms. Both small molecule functionalization and e-beam irradiation was evaluated as a means to enhance tensile strength and Youngs modulus of the bulk CNT material. Mechanical testing results revealed a tensile strength increase in CNT sheets by 57 when functionalized, while an additional 48 increase in tensile strength was observed when functionalized sheets were irradiated; compared to unfunctionalized sheets. Similarly, small molecule functionalization increased yarn tensile strength up to 25, whereas irradiation of the functionalized yarns pushed the tensile strength to 88 beyond that of the baseline yarn.

STRESS - STRAIN CURVE ANALYSIS OF WOVEN FABRICS MAD E FROM COMBED YARNS TYPE WOOL

Directory of Open Access Journals (Sweden)

VÎLCU Adrian

2014-05-01

Full Text Available The paper analyses the tensile behavior of woven fabrics made from 45%Wool + 55% PES used for garments. Analysis of fabric behavior during wearing has shown that these are submitted to simple and repeated uni-axial or bi-axial tensile strains. The level of these strains is often within the elastic limit, rarely going over yielding. Therefore the designer must be able to evaluate the mechanical behavior of such fabrics in order to control the fabric behavior in the garment. This evaluation is carried out based on the tensile testing, using certain indexes specific to the stress-strain curve. The paper considers an experimental matrix based on woven fabrics of different yarn counts, different or equal yarn count for warp and weft systems and different structures. The fabrics were tested using a testing machine and the results were then compared in order to determine the fabrics’ tensile behavior and the factors of influence that affect it.From the point of view of tensile testing, the woven materials having twill weave are preferable because this type of structure is characterized by higher durability and better yarn stability in the fabric. In practice, the woven material must exhibit an optimum behavior to repeated strains, flexions and abrasions during wearing process. The analysis of fabrics tensile properties studied by investigation of stress-strain diagrams reveals that the main factors influencing the tensile strength are: yarns fineness, technological density of those two systems of yarns and the weaving type.

Parachuting plasmapheresis into the Ebola crisis | Zacharias | Africa ...

African Journals Online (AJOL)

Parachuting plasmapheresis into the Ebola crisis. ... A vehicle was pre-fitted with sophisticated equipment and airlifted to the study site (ELWA). ... Training included plasmapheresis, donor management, testing and pathogen inactivation.

Moisture properties of raised 3-thread fleece fabric knitted with different face and fleecy yarns

Directory of Open Access Journals (Sweden)

Alaa Arafa Badr

2016-09-01

So, in this study, nine three-thread fleece fabrics of different composition materials have been studied, where these knitted fabrics are produced in a special circular knitted machine. The developed fabrics are taken to measure, water vapor permeability “WVP”, gain%, air permeability, drying time, color difference, immersion time and bursting strength. The test results were discussed statistically with single factor ANOVA. From the experimental results, it has been observed that the difference between face and fleecy yarns material was highly significant for the whole fabric in the water vapor permeability, gain%, color difference and immersion time. Three-thread Fleece fabric knitted with Egyptian cotton for the face and fleecy yarns has the maximum bursting strength compared to other samples having Bamboo and Tencel yarns.

Measurement of Electromagnetic Shielding Effectiveness of Woven Fabrics Containing Metallic Yarns by Mobile Devices

Directory of Open Access Journals (Sweden)

Erhan Kenan ÇEVEN

2016-10-01

Full Text Available In this study, we introduce an alternative method to evaluate the electromagnetic shielding effectiveness (EMSE of woven fabrics containing metal wires. For experimental measurements, hybrid silk viscose yarns containing metal wires were first produced. Conductive test fabrics were then produced using the hybrid weft yarns and polyester warp yarns. The produced fabrics were separated in two parts and laminated together after rotating one fabric by 90 degrees to create a grid structure. The laminated fabrics were then folded by several times to create multiple layers such as 2,4,8,12,16. The EMSE of the multiple layered fabrics was measured over GSM signals received by a mobile device. For EMSE evaluation, the mobile device was placed between the laminated fabrics. The EMSE values of the fabrics were then calculated in accordance with the power variations of GSM signals.

Computational fluid dynamic (CFD) analysis on ALUDRA SR-10 UAV with parachute recovery system

Science.gov (United States)

Saim, R.; Mohd, S.; Shamsudin, S. S.; Zulkifli, M. F.; Omar, Z.; Subari@Rahmat, Z.; Masrom, M. F. Mohd; Zaki, Y.

2017-09-01

In an operation, belly landing is mostly applied as recovery method especially on research Unmanned Aerial Vehicle (UAV) such as Aludra SR-10. This type of landing method may encounter tough landing on hard soil and gravel which create high impact load on the aircraft. The impact may cause structural or system damage which costly to be repaired. Nowadays, Parachute Recovery System (PRS) recently used in numerous different tasks such as landing purpose to replace belly landing technique. Parachute use in this system to slow down flying or falling UAV to a safe landing by opening the canopy to increase aerodynamic drag. This paper was described the Computational Fluid Dynamic (CFD) analysis on ALUDRA SR-10 model with two different conditions i.e. the UAV equipped with and without parachute in order to identify the changes of aerodynamic characteristics. This simulation studies using solid models of aircraft and hemisphere parachute and was carried out by using ANSYS 16.0 Fluent under steady and turbulent flow and was modelled using the k-epsilon (k-ε) turbulence model. This simulation was limited to determine the drag force and drag coefficient. The obtained result showed that implementation of parachute increase 0.25 drag coefficient of the aircraft that is from 0.93 to 1.18. Subsequent to the reduction of descent rate caused by the parachute, the drag force of the aircraft increase by 0.76N. These increasing of drag force of the aircraft will produce lower terminal velocity which is expected to reduce the impact force on the aircraft during landing.

Self-plied and twist-stable carbon nanotube yarn artificial muscles driven by organic solvent adsorption.

Science.gov (United States)

Jin, Kaiyun; Zhang, Silan; Zhou, Susheng; Qiao, Jian; Song, Yanhui; Di, Jiangtao; Zhang, Dengsong; Li, Qingwen

2018-05-03

Artificial yarn/fiber muscles have recently attracted considerable interest for various applications. These muscles can provide large-stroke tensile and torsional actuations, resulting from inserted twists. However, tensional tethering of twisted muscles is generally needed to avoid muscle snarling and untwisting. In this paper a carbon nanotube (CNT) yarn muscle that is tethering-free and twist-stable is reported. The yarn muscle is prepared by allowing the self-plying of a coiled CNT yarn. When driven by acetone adsorption, this muscle shows decoupled actuations, which provide fast and reversible ∼13.3% contraction strain against a constant stress corresponding to ∼38 000 times the muscle weight but almost zero torsional strokes. The cycling test shows that the self-plied muscle has very good structural stability and actuation reversibility. Applied joule heating can help increase the desorption of acetone and increase the operation frequency of the self-plied muscle. Furthermore, by controlling the coupling between the joule heating and acetone adsorption/desorption, tensile actuations from negative to positive have been achieved. This twist-stable feature could considerably facilitate the practical applications of such muscle.

Pilot ejection, parachute, and helicopter crash injuries.

Science.gov (United States)

McBratney, Colleen M; Rush, Stephen; Kharod, Chetan U

2014-01-01

USAF Pararescuemen (PJs) respond to downed aircrew as a fundamental mission for personnel recovery (PR), one of the Air Force's core functions. In addition to responding to these in Military settings, the PJs from the 212 Rescue Squadron routinely respond to small plane crashes in remote regions of Alaska. While there is a paucity of information on the latter, there have been articles detailing injuries sustained from helicopter crashes and while ejecting or parachuting from fixed wing aircraft. The following represents a new chapter added to the Pararescue Medical Operations Handbook, Sixth Edition (2014, editors Matt Wolf, MD, and Stephen Rush, MD, in press). It was designed to be a quick reference for PJs and their Special Operations flight surgeons to help with understanding of mechanism of injury with regard to pilot ejection, parachute, and helicopter accident injuries. It outlines the nature of the injuries sustained in such mishaps and provides an epidemiologic framework from which to approach the problem. 2014.

Electrically, Chemically, and Photonically Powered Torsional and Tensile Actuation of Hybrid Carbon Nanotube Yarn Muscles

Science.gov (United States)

Lima, Márcio D.; Li, Na; Jung de Andrade, Mônica; Fang, Shaoli; Oh, Jiyoung; Spinks, Geoffrey M.; Kozlov, Mikhail E.; Haines, Carter S.; Suh, Dongseok; Foroughi, Javad; Kim, Seon Jeong; Chen, Yongsheng; Ware, Taylor; Shin, Min Kyoon; Machado, Leonardo D.; Fonseca, Alexandre F.; Madden, John D. W.; Voit, Walter E.; Galvão, Douglas S.; Baughman, Ray H.

2012-11-01

Artificial muscles are of practical interest, but few types have been commercially exploited. Typical problems include slow response, low strain and force generation, short cycle life, use of electrolytes, and low energy efficiency. We have designed guest-filled, twist-spun carbon nanotube yarns as electrolyte-free muscles that provide fast, high-force, large-stroke torsional and tensile actuation. More than a million torsional and tensile actuation cycles are demonstrated, wherein a muscle spins a rotor at an average 11,500 revolutions/minute or delivers 3% tensile contraction at 1200 cycles/minute. Electrical, chemical, or photonic excitation of hybrid yarns changes guest dimensions and generates torsional rotation and contraction of the yarn host. Demonstrations include torsional motors, contractile muscles, and sensors that capture the energy of the sensing process to mechanically actuate.

Carbon nanotube yarns as strong flexible conductive capacitive electrodes

NARCIS (Netherlands)

Liu, F.; Wagterveld, R.M.; Gebben, B.; Otto, M.J.; Biesheuvel, P.M.; Hamelers, H.V.M.

2015-01-01

Carbon nanotube (CNT) yarn, consisting of 23 µm diameter CNT filaments, can be used as capacitive electrodes that are long, flexible, conductive and strong, for applications in energy and electrochemical water treatment. We measure the charge storage capacity as function of salt concentration, and

Validation of Multibody Program to Optimize Simulated Trajectories II Parachute Simulation with Interacting Forces

Science.gov (United States)

Raiszadeh, Behzad; Queen, Eric M.; Hotchko, Nathaniel J.

2009-01-01

A capability to simulate trajectories of multiple interacting rigid bodies has been developed, tested and validated. This capability uses the Program to Optimize Simulated Trajectories II (POST 2). The standard version of POST 2 allows trajectory simulation of multiple bodies without force interaction. In the current implementation, the force interaction between the parachute and the suspended bodies has been modeled using flexible lines, allowing accurate trajectory simulation of the individual bodies in flight. The POST 2 multibody capability is intended to be general purpose and applicable to any parachute entry trajectory simulation. This research paper explains the motivation for multibody parachute simulation, discusses implementation methods, and presents validation of this capability.

Electro-spun PLA-PEG-yarns for tissue engineering applications

NARCIS (Netherlands)

Kruse, Magnus; Greuel, Marc; Kreimendahl, Franziska; Schneiders, Thomas; Bauer, Benedict; Gries, Thomas; Jockenhoevel, Stefan

2018-01-01

Electro-spinning is widely used in tissue-engineered applications mostly in form of non-woven structures. The development of e-spun yarn opens the door for textile fabrics which combine the micro to nanoscale dimension of electro-spun filaments with three-dimensional (3D) drapable textile fabrics.

Improved control system power unit for large parachutes

Science.gov (United States)

Chandler, J. A.; Grubbs, T. M.

1968-01-01

Improved control system power unit drives the control surfaces of very large controllable parachutes. The design features subassemblies for determining control surface position and cable loading, and protection of the load sensor against the possibility of damage during manipulation.

Parachute diverts ventilation fast

Energy Technology Data Exchange (ETDEWEB)

Chironis, N.P.

1990-02-01

The USBM Pittsburgh Research Center is developing a simple, inexpensive and highly effective new technique for keeping smoke and toxic gases out of intake escapeways during mine fires. The technique involves the use of a special parachute which fixes onto a roof bolt plate or strap, and is automatically inflated by incoming air. The chute thus becomes a quick-erect check curtain which leaks much less than conventional curtains. The air pressure in the intake quickly climbs, making it unlikely that any smoke from an adjacent entry would be able to migrate into the intake. 2 figs.

Influence of irrigation water types and stress levels on cotton fibre and yarn quality for different varieties

International Nuclear Information System (INIS)

Nazar, A.; Ishaq, W.

2012-01-01

Cotton fibre quality is being deteriorated day by day due to various reasons and shortage/ poor quality of irrigation water is one of the reasons for the low quality of cotton fibre. The effect of the stress of water can be seen on the fibre length, strength and elongation. All these properties of fibre have also a significant influence on yarn characteristics and thus the yarn quality is also dependent on agronomic practices including irrigation. When new varieties are evolved it becomes necessary to examine such cotton varieties keenly, so that one which reflects maximum agricultural as well as industrial benefits can be recommended. The present study was planned to explore the spinning performance of various cotton varieties under different water quality treatments and water stress levels. Cotton of four varieties (CIM-501, CIM-496, CIM-499, and NIAB-111) under different types of irrigation water (canal water and tube well water) and different water stress levels (75ET, 100ET and 125ET) were selected for this research. The effect of these treatments was investigated on cotton fibre span length, strength and fibre elongation as well as on yarn quality. The study revealed that effect of different cotton varieties, water types and water stress levels on fibre and yarn quality was highly significant. Yarn characteristics showed greater values for the canal water similarly fibre length and elongations were better for canal water. Yarn tensile properties were decreased with increase in the water stress. The overall results indicated that the cotton variety NIAB-111 performed better as compared to other varieties. It is suggested that the cotton farmers may be trained by the agri. extension staff regarding maintenance of fibre quality through cultural practices and better irrigation techniques. (author)

48 CFR 252.225-7012 - Preference for certain domestic commodities.

Science.gov (United States)

2010-10-01

..., office, or other use); and (D) Parachutes (Federal Supply Class 1670); or (ii) The fibers and yarns are..., materials, or manufactured articles). (10) Any item of individual equipment (Federal Supply Class 8465... end product; and (ii) Does not exceed the simplified acquisition threshold in FAR part 2; (3) To waste...

Recycling of warp size materials and comparison of yarn mechanical properties sized with recycled materials and virgin materials

NARCIS (Netherlands)

Maqsood, Muhammad

2017-01-01

Warp sizing is an established method for improving the weaveability of textile yarns by coating or impregnating warp yarns with a polymer that improves the efficiency of the weaving operation. Despite its high cost, polyvinyl alcohol (PVA) normally shows better adhesion to fibers than other sizing

Ribbon and gliding type parachutes evaluated in the 7 by 10 foot transonic wind tunnel

Energy Technology Data Exchange (ETDEWEB)

Ottensoser, J.

1975-09-01

An experiment has been conducted in the NSRDC 7- x 10-foot transonic tunnel for the Sandia Corporation to evaluate various parachute parameters. The experiment consisted of three main parts: the first phase evaluated the disreefing characteristics of the various parachutes as well as the drag forces before, during, and after disreefing; the second phase measured the pressure distribution around the chute as well as the drag forces; and the final phase evaluated the disreefing and drag characteristics of gliding type parachutes. The free stream dynamic pressure varied from 65 to 500 psf. 12 figures, 1 table. (auth)

Export taxes and sectoral economic growth: evidence from cotton and yarn markets in Pakistan

OpenAIRE

Hudson, Darren; Ethridge, Don

1999-01-01

Pakistan used an export tax on raw cotton from 1988-1995 in order to suppress the internal price of cotton to benefit the domestic yarn industry. An analysis was conducted to estimate the impact of this policy on both the cotton and yarn sectors. These effects were simulated using the results of a structural econometric model of these sectors of Pakistan's economy. Results indicated that the export tax had a negative impact on the growth rate in the cotton sector, while having little or no im...

雅赛尔纱线的开发%Development of Gracell Yarn

Institute of Scientific and Technical Information of China (English)

赵学玉; 赵娜; 丁莉燕; 邢明杰; 田绍旭

2017-01-01

Production key points for pure Gracell fiber spinning were discussed.Properties and physical indexes of Gracell fiber were introduced.Moisture regain of raw material was well controlled.The yarn unevenness of drawn silver was reduced by controlling the beater speed,improving fiber straightness,improving extended paral lelization & separation degree of card silver and so on.Roving twist factor was optimized.Processing parameters and special spinning equipment were reasonably selected.Meanwhile,the management and cleaning of workshop were well done.The temperature and humidity of workshop was well controlled.Then the Gracell 27.8 tex yarn was successfully spun and the product quality could meet the design requirement.It is considered that well grasping the processing configuration of Gracell serial yarn is beneficial to the development of colored spun yarn.%探讨雅赛尔纤维纯纺纱的生产实践要点.介绍了雅赛尔纤维的性能及物理指标.控制好原料回潮率,通过提高纤维开松度,控制打手速度,提高纤维伸直度,改善生条伸直平行度和分离度等措施降低熟条条干不匀率;优选粗纱捻系数,合理选择细纱工艺参数和纺专器材,同时做好车间管理和清洁,控制好车间温湿度,从而顺利纺制出雅赛尔27.8 tex纱,产品质量达到设计要求.认为:掌握好雅赛尔系列纱线的工艺配置有助于色纺纱的开发.

ASPECTS OF THE INFLUENCE OF TECHNOLOGICAL PARAMETERS ON THE TENSION PROPERTIES OF THE YARNS

Directory of Open Access Journals (Sweden)

HRISTIAN Liliana

2016-05-01

Full Text Available This paper presents the results of some experiments performed using the power system bands directly from the card to the rotor spinning machine and the spinning system used by passing the lanes on two passages mill and fed to the spinning rotor. In this study we analized the influence of technological parameters of the preparation drawing on the assessing indicators for the tensile strength of the Nm20, Nm24, Nm27 Nm34 and Nm40 yarns. The fineness range studied was made of three fiber mixtures of different varieties of cotton, coded as follows: A1-85% Soviet cotton+15% Chinese cotton medium II; A2-100% Turkish cotton medium III; A3-100% American cotton mdium IV. The method of preparation of the bands which are to be powered to the rotor spinning machine, respectively with the aggregate pile-card and the powered bands directly to the rotor spinning machine and the adding of two rolling mill, detemines different structures of bands and different degrees of untangling and orientation of the fibers, which influences the quality of the obtained yarns. This study reveals a considerable improvement of the tensile properties when the yarns are made from rolled band, which is explained by the high degree of correction and parallelization of the fibers of the rolled band, which allows a greater participation of fibers with their resistance to the resistance of the yarns.

Percutaneous Implantation of A Parachute Device For Treatment of Ischemic Heart Failure

Energy Technology Data Exchange (ETDEWEB)

Cilingiroglu, Mehmet, E-mail: mcilingiroglu@yahoo.com; Rollefson, William A.; Mego, David

2013-07-15

Congestive heart failure (CHF) secondary to ischemic cardiomyopathy is associated with significant morbidity and mortality despite currently available medical therapy. The Parachute{sup TM} device is a novel left ventricular partitioning device that is delivered percutaneously in the left ventricle (LV) in patients with anteroapical regional wall motion abnormalities, dilated LV and systolic dysfunction after anterior myocardial infarction with favorable clinical and LV hemodynamic improvements post-implantation. Here, we do review the current literature and present a case of the Parachute device implantation.

Percutaneous Implantation of A Parachute Device For Treatment of Ischemic Heart Failure

International Nuclear Information System (INIS)

Cilingiroglu, Mehmet; Rollefson, William A.; Mego, David

2013-01-01

Congestive heart failure (CHF) secondary to ischemic cardiomyopathy is associated with significant morbidity and mortality despite currently available medical therapy. The Parachute TM device is a novel left ventricular partitioning device that is delivered percutaneously in the left ventricle (LV) in patients with anteroapical regional wall motion abnormalities, dilated LV and systolic dysfunction after anterior myocardial infarction with favorable clinical and LV hemodynamic improvements post-implantation. Here, we do review the current literature and present a case of the Parachute device implantation

Electrospinning of continuous poly (L-lactide) yarns : Effect of twist on the morphology, thermal properties and mechanical behavior

NARCIS (Netherlands)

Maleki, H.; Gharehaghaji, A.A.; Dijkstra, P. J.

2017-01-01

Electrospinning PLLA solutions from two oppositely charged nozzles gives a triangle of fibers, also called E-triangle, that assemble into yarns at the convergence point. The formed yarn at the E-triangle was taken up by a unit comprising a take up roller and coupled twister plate, which twist rate

Development of Flame Resistant Combat Uniform Fabrics Made from Long Staple Wool and Aramid Blend Yarn

Science.gov (United States)

2013-04-15

Kentwool recombed the wool top ( wool is first combed during the production of wool top); a second combing process is an optional step sometimes used in...RESISTANT COMBAT UNIFORM FABRICS MADE FROM LONG STAPLE WOOL AND ARAMID BLEND YARN by Parvez Mehta* Mitchell Driggers* and Carole...SUBTITLE DEVELOPMENT OF FLAME RESISTANT COMBAT UNIFORM FABRICS MADE FROM LONG STAPLE WOOL AND ARAMID BLEND YARN 5a. CONTRACT NUMBER W911QY-11

Investigation of Shielding Properties of Yarns, Twisted with Metal Wire

Directory of Open Access Journals (Sweden)

Sandra VARNAITĖ-ŽURAVLIOVA

2014-04-01

Full Text Available The development level of the modern techniques and information technologies creates diverse nature electromagnetic fields and electric field accumulations in the human environment. Electrically conductive textiles that protect against electromagnetic waves and electric charge accumulations can be usable as protective covers for work in computer equipment rooms, measuring stands, air and gas filters and so on. One of the methods used in increase of electrical conductivity in textiles is the development of their specific structures (including the development of threads with the metal component. In this paper, unlike the currently used in the world conductive material production method, where different metal fibres are used as an additives to the main fibre composition in order to create a variety of fibres and yarns, a spun yarn with metal wire was prototyped as samples for this research and the parameters of protective properties of these samples were investigated (such as surface resistivity, vertical resistance, etc.. The protective and shielding properties of woven network with prototyped twisted electro conductive thread with a wire (metal wire diameter of 15 microns were investigated. During the investigation the influence of the following factors, such as conductive fibre composition, electrically conductive thread distribution frequency of the longitudinal and transverse direction, on the protective shielding properties of conductive network were analyzed. The research enabled the assessment of influence of electrically conductive fibre yarn composition and its distribution in the woven mesh on protective shielding properties. DOI: http://dx.doi.org/10.5755/j01.ms.20.1.2492

Weavable, Conductive Yarn-Based NiCo//Zn Textile Battery with High Energy Density and Rate Capability.

Science.gov (United States)

Huang, Yan; Ip, Wing Shan; Lau, Yuen Ying; Sun, Jinfeng; Zeng, Jie; Yeung, Nga Sze Sea; Ng, Wing Sum; Li, Hongfei; Pei, Zengxia; Xue, Qi; Wang, Yukun; Yu, Jie; Hu, Hong; Zhi, Chunyi

2017-09-26

With intrinsic safety and much higher energy densities than supercapacitors, rechargeable nickel/cobalt-zinc-based textile batteries are promising power sources for next generation personalized wearable electronics. However, high-performance wearable nickel/cobalt-zinc-based batteries are rarely reported because there is a lack of industrially weavable and knittable highly conductive yarns. Here, we use scalably produced highly conductive yarns uniformly covered with zinc (as anode) and nickel cobalt hydroxide nanosheets (as cathode) to fabricate rechargeable yarn batteries. They possess a battery level capacity and energy density, as well as a supercapacitor level power density. They deliver high specific capacity of 5 mAh cm -3 and energy densities of 0.12 mWh cm -2 and 8 mWh cm -3 (based on the whole solid battery). They exhibit ultrahigh rate capabilities of 232 C (liquid electrolyte) and 116 C (solid electrolyte), which endows the batteries excellent power densities of 32.8 mW cm -2 and 2.2 W cm -3 (based on the whole solid battery). These are among the highest values reported so far. A wrist band battery is further constructed by using a large conductive cloth woven from the conductive yarns by a commercial weaving machine. It powers various electronic devices successfully, enabling dual functions of wearability and energy storage.

The Development of an IMU Integrated Clothes for Postural Monitoring Using Conductive Yarn and Interconnecting Technology.

Science.gov (United States)

Kang, Sung-Won; Choi, Hyeob; Park, Hyung-Il; Choi, Byoung-Gun; Im, Hyobin; Shin, Dongjun; Jung, Young-Giu; Lee, Jun-Young; Park, Hong-Won; Park, Sukyung; Roh, Jung-Sim

2017-11-07

Spinal disease is a common yet important condition that occurs because of inappropriate posture. Prevention could be achieved by continuous posture monitoring, but most measurement systems cannot be used in daily life due to factors such as burdensome wires and large sensing modules. To improve upon these weaknesses, we developed comfortable "smart wear" for posture measurement using conductive yarn for circuit patterning and a flexible printed circuit board (FPCB) for interconnections. The conductive yarn was made by twisting polyester yarn and metal filaments, and the resistance per unit length was about 0.05 Ω/cm. An embroidered circuit was made using the conductive yarn, which showed increased yield strength and uniform electrical resistance per unit length. Circuit networks of sensors and FPCBs for interconnection were integrated into clothes using a computer numerical control (CNC) embroidery process. The system was calibrated and verified by comparing the values measured by the smart wear with those measured by a motion capture camera system. Six subjects performed fixed movements and free computer work, and, with this system, we were able to measure the anterior/posterior direction tilt angle with an error of less than 4°. The smart wear does not have excessive wires, and its structure will be optimized for better posture estimation in a later study.

Yarning/Aboriginal storytelling: towards an understanding of an Indigenous perspective and its implications for research practice.

Science.gov (United States)

Geia, Lynore K; Hayes, Barbara; Usher, Kim

2013-12-01

There is increasing recognition of Indigenous perspectives from various parts of the world in relation to storytelling, research and its effects on practice. The recent emergence of storytelling or yarning as a research method in Australian Aboriginal and Torres Strait Island studies and other Indigenous peoples of the world is gaining momentum. Narratives, stories, storytelling and yarning are emerging methods in research and has wide ranging potential to shape conventional research discourse making research more meaningful and accessible for researchers. In this paper we argue for the importance of Indigenous research methods and Indigenous method(ology), within collaborative respectful partnerships with non-Indigenous researchers. It is imperative to take these challenging steps together towards better outcomes for Indigenous people and their communities. In the Australian context we as researchers cannot afford to allow the gap between Aboriginal and Torres Strait Islanders and mainstream Australia health outcomes to grow even wider. One such pathway is the inclusion of Aboriginal storytelling or yarning from an Aboriginal and Torres Strait perspective within Indigenous and non-Indigenous research paradigms. Utilising Aboriginal storytelling or yarning will provide deeper understanding; complementing a two-way research paradigm for collaborative research. Furthermore, it has significant social implications for research and clinical practice amongst Indigenous populations; thus complementing the biomedical medical paradigm.

Parachute technique for partial penectomy

Directory of Open Access Journals (Sweden)

Fernando Korkes

2010-04-01

Full Text Available PURPOSE: Penile carcinoma is a rare but mutilating malignancy. In this context, partial penectomy is the most commonly applied approach for best oncological results. We herein propose a simple modification of the classic technique of partial penectomy, for better cosmetic and functional results. TECHNIQUE: If partial penectomy is indicated, the present technique can bring additional benefits. Different from classical technique, the urethra is spatulated only ventrally. An inverted "V" skin flap with 0.5 cm of extension is sectioned ventrally. The suture is performed with vicryl 4-0 in a "parachute" fashion, beginning from the ventral portion of the urethra and the "V" flap, followed by the "V" flap angles and than by the dorsal portion of the penis. After completion of the suture, a Foley catheter and light dressing are placed for 24 hours. CONCLUSIONS: Several complex reconstructive techniques have been previously proposed, but normally require specific surgical abilities, adequate patient selection and staged procedures. We believe that these reconstructive techniques are very useful in some specific subsets of patients. However, the technique herein proposed is a simple alternative that can be applied to all men after a partial penectomy, and takes the same amount of time as that in the classic technique. In conclusion, the "parachute" technique for penile reconstruction after partial amputation not only improves the appearance of the penis, but also maintains an adequate function.

Bio-inspired, Moisture-Powered Hybrid Carbon Nanotube Yarn Muscles.

Science.gov (United States)

Kim, Shi Hyeong; Kwon, Cheong Hoon; Park, Karam; Mun, Tae Jin; Lepró, Xavier; Baughman, Ray H; Spinks, Geoffrey M; Kim, Seon Jeong

2016-03-14

Hygromorph artificial muscles are attractive as self-powered actuators driven by moisture from the ambient environment. Previously reported hygromorph muscles have been largely limited to bending or torsional motions or as tensile actuators with low work and energy densities. Herein, we developed a hybrid yarn artificial muscle with a unique coiled and wrinkled structure, which can be actuated by either changing relative humidity or contact with water. The muscle provides a large tensile stroke (up to 78%) and a high maximum gravimetric work capacity during contraction (2.17 kJ kg(-1)), which is over 50 times that of the same weight human muscle and 5.5 times higher than for the same weight spider silk, which is the previous record holder for a moisture driven muscle. We demonstrate an automatic ventilation system that is operated by the tensile actuation of the hybrid muscles caused by dew condensing on the hybrid yarn. This self-powered humidity-controlled ventilation system could be adapted to automatically control the desired relative humidity of an enclosed space.

Innovations in Air Insertion (Involving Parachutes)

Science.gov (United States)

2008-03-01

loadings and different trim. .........48 Figure 16. Thermal being radiated from a ploughed field.50 Figure 17. A series of ridges can amplify a wave and...Crews," MHQ: The Quarterly Journal of Military History 10, no. Autumn 1998 (1998), 99. 5 Niedermeyer was killed in March of 1922 did parachutes...was killed on a 1998 wing suit jump, the cause was not wing suit related but rather the result of an easily preventable rigging

Self-socialization: a case study of a parachute child.

Science.gov (United States)

Newman, Philip R; Newman, Barbara M

2009-01-01

The theoretical concept of self-socialization suggests that an individual is able to reflect on the self, formulate a vision of a future self, set goals, and take actions that create or alter the developmental trajectory. This case study of a parachute child illustrates how a person constructs her life from a very young age, drawing on a profound capacity for personal agency to overcome obstacles, identify resources, and internalize values to build a life structure. A model of the psychosocial process of self-socialization emerges from this case. Following the disruption of a well-defined trajectory, self-socialization is observed as a sequence of actions, reflection, correction, and new actions. Self-socialization is possible when a strong sense of self-efficacy is applied to attaining internalized values and goals.

Foil Strain Gauges Using Piezoresistive Carbon Nanotube Yarn: Fabrication and Calibration

Directory of Open Access Journals (Sweden)

Jandro L. Abot

2018-02-01

Full Text Available Carbon nanotube yarns are micron-scale fibers comprised by tens of thousands of carbon nanotubes in their cross section and exhibiting piezoresistive characteristics that can be tapped to sense strain. This paper presents the details of novel foil strain gauge sensor configurations comprising carbon nanotube yarn as the piezoresistive sensing element. The foil strain gauge sensors are designed using the results of parametric studies that maximize the sensitivity of the sensors to mechanical loading. The fabrication details of the strain gauge sensors that exhibit the highest sensitivity, based on the modeling results, are described including the materials and procedures used in the first prototypes. Details of the calibration of the foil strain gauge sensors are also provided and discussed in the context of their electromechanical characterization when bonded to metallic specimens. This characterization included studying their response under monotonic and cyclic mechanical loading. It was shown that these foil strain gauge sensors comprising carbon nanotube yarn are sensitive enough to capture strain and can replicate the loading and unloading cycles. It was also observed that the loading rate affects their piezoresistive response and that the gauge factors were all above one order of magnitude higher than those of typical metallic foil strain gauges. Based on these calibration results on the initial sensor configurations, new foil strain gauge configurations will be designed and fabricated, to increase the strain gauge factors even more.

Foil Strain Gauges Using Piezoresistive Carbon Nanotube Yarn: Fabrication and Calibration

Science.gov (United States)

Góngora-Rubio, Mário R.; Kiyono, César Y.; Mello, Luis A. M.; Cardoso, Valtemar F.; Rosa, Reinaldo L. S.; Kuebler, Derek A.; Brodeur, Grace E.; Alotaibi, Amani H.; Coene, Marisa P.; Coene, Lauren M.; Jean, Elizabeth; Santiago, Rafael C.; Oliveira, Francisco H. A.; Rangel, Ricardo; Thomas, Gilles P.; Belay, Kalayu; da Silva, Luciana W.; Moura, Rafael T.; Seabra, Antonio C.; Silva, Emílio C. N.

2018-01-01

Carbon nanotube yarns are micron-scale fibers comprised by tens of thousands of carbon nanotubes in their cross section and exhibiting piezoresistive characteristics that can be tapped to sense strain. This paper presents the details of novel foil strain gauge sensor configurations comprising carbon nanotube yarn as the piezoresistive sensing element. The foil strain gauge sensors are designed using the results of parametric studies that maximize the sensitivity of the sensors to mechanical loading. The fabrication details of the strain gauge sensors that exhibit the highest sensitivity, based on the modeling results, are described including the materials and procedures used in the first prototypes. Details of the calibration of the foil strain gauge sensors are also provided and discussed in the context of their electromechanical characterization when bonded to metallic specimens. This characterization included studying their response under monotonic and cyclic mechanical loading. It was shown that these foil strain gauge sensors comprising carbon nanotube yarn are sensitive enough to capture strain and can replicate the loading and unloading cycles. It was also observed that the loading rate affects their piezoresistive response and that the gauge factors were all above one order of magnitude higher than those of typical metallic foil strain gauges. Based on these calibration results on the initial sensor configurations, new foil strain gauge configurations will be designed and fabricated, to increase the strain gauge factors even more. PMID:29401745

Sucrose Treated Carbon Nanotube and Graphene Yarns and Sheets

Science.gov (United States)

Sauti, Godfrey (Inventor); Kim, Jae-Woo (Inventor); Siochi, Emilie J. (Inventor); Wise, Kristopher E. (Inventor)

2017-01-01

Consolidated carbon nanotube or graphene yarns and woven sheets are consolidated through the formation of a carbon binder formed from the dehydration of sucrose. The resulting materials, on a macro-scale are lightweight and of a high specific modulus and/or strength. Sucrose is relatively inexpensive and readily available, and the process is therefore cost-effective.

Application of an automatic yarn dismantler to track changes in cotton fibre properties during processing on a miniature spinning line

CSIR Research Space (South Africa)

Fassihi, A

2014-11-01

Full Text Available . The results obtained on different Upland cottons have clearly demonstrated the practical value of the yarn dismantler in enabling yarns to be automatically dismantled into their constituent fibres, which can then be tested by instrument, such as the AFIS...

Asymptotic Parachute Performance Sensitivity

Science.gov (United States)

Way, David W.; Powell, Richard W.; Chen, Allen; Steltzner, Adam D.

2006-01-01

In 2010, the Mars Science Laboratory mission will pioneer the next generation of robotic Entry, Descent, and Landing systems by delivering the largest and most capable rover to date to the surface of Mars. In addition to landing more mass than any other mission to Mars, Mars Science Laboratory will also provide scientists with unprecedented access to regions of Mars that have been previously unreachable. By providing an Entry, Descent, and Landing system capable of landing at altitudes as high as 2 km above the reference gravitational equipotential surface, or areoid, as defined by the Mars Orbiting Laser Altimeter program, Mars Science Laboratory will demonstrate sufficient performance to land on 83% of the planet s surface. By contrast, the highest altitude landing to date on Mars has been the Mars Exploration Rover at 1.3 km below the areoid. The coupling of this improved altitude performance with latitude limits as large as 60 degrees off of the equator and a precise delivery to within 10 km of a surface target, will allow the science community to select the Mars Science Laboratory landing site from thousands of scientifically interesting possibilities. In meeting these requirements, Mars Science Laboratory is extending the limits of the Entry, Descent, and Landing technologies qualified by the Mars Viking, Mars Pathfinder, and Mars Exploration Rover missions. Specifically, the drag deceleration provided by a Viking-heritage 16.15 m supersonic Disk-Gap-Band parachute in the thin atmosphere of Mars is insufficient, at the altitudes and ballistic coefficients under consideration by the Mars Science Laboratory project, to maintain necessary altitude performance and timeline margin. This paper defines and discusses the asymptotic parachute performance observed in Monte Carlo simulation and performance analysis and its effect on the Mars Science Laboratory Entry, Descent, and Landing architecture.

Identification of cotton properties to improve yarn count quality by using regression analysis

International Nuclear Information System (INIS)

Amin, M.; Ullah, M.; Akbar, A.

2014-01-01

Identification of raw material characteristics towards yarn count variation was studied by using statistical techniques. Regression analysis is used to meet the objective. Stepwise regression is used for mode) selection, and coefficient of determination and mean squared error (MSE) criteria are used to identify the contributing factors of cotton properties for yam count. Statistical assumptions of normality, autocorrelation and multicollinearity are evaluated by using probability plot, Durbin Watson test, variance inflation factor (VIF), and then model fitting is carried out. It is found that, invisible (INV), nepness (Nep), grayness (RD), cotton trash (TR) and uniformity index (VI) are the main contributing cotton properties for yarn count variation. The results are also verified by Pareto chart. (author)

The Development of an IMU Integrated Clothes for Postural Monitoring Using Conductive Yarn and Interconnecting Technology

Directory of Open Access Journals (Sweden)

Sung-Won Kang

2017-11-01

Full Text Available Spinal disease is a common yet important condition that occurs because of inappropriate posture. Prevention could be achieved by continuous posture monitoring, but most measurement systems cannot be used in daily life due to factors such as burdensome wires and large sensing modules. To improve upon these weaknesses, we developed comfortable “smart wear” for posture measurement using conductive yarn for circuit patterning and a flexible printed circuit board (FPCB for interconnections. The conductive yarn was made by twisting polyester yarn and metal filaments, and the resistance per unit length was about 0.05 Ω/cm. An embroidered circuit was made using the conductive yarn, which showed increased yield strength and uniform electrical resistance per unit length. Circuit networks of sensors and FPCBs for interconnection were integrated into clothes using a computer numerical control (CNC embroidery process. The system was calibrated and verified by comparing the values measured by the smart wear with those measured by a motion capture camera system. Six subjects performed fixed movements and free computer work, and, with this system, we were able to measure the anterior/posterior direction tilt angle with an error of less than 4°. The smart wear does not have excessive wires, and its structure will be optimized for better posture estimation in a later study.

Supersonic Testing of 0.8 m Disk Gap Band Parachutes in the Wake of a 70 Deg Sphere Cone Entry Vehicle

Science.gov (United States)

Sengupta, Anita; Wernet, Mark; Roeder, James; Kelsch, Richard; Witkowski, Al; Jones, Thomas

2009-01-01

Supersonic wind tunnel testing of Viking-type 0.8 m Disk-Gap-Band (DGB) parachutes was conducted in the NASA Glenn Research Center 10'x10' wind-tunnel. The tests were conducted in support of the Mars Science Laboratory Parachute Decelerator System development and qualification program. The aerodynamic coupling of the entry-vehicle wake to parachute flow-field is under investigation to determine the cause and functional dependence of a supersonic canopy breathing phenomenon referred to as area oscillations, characteristic of DGB's above Mach 1.5 operation. Four percent of full-scale parachutes (0.8 m) were constructed similar to the flight-article in material and construction techniques. The parachutes were attached to a 70-deg sphere-cone entry-vehicle to simulate the Mars flight configuration. The parachutes were tested in the wind-tunnel from Mach 2 to 2.5 in a Reynolds number range of 2x105 to 1x106, representative of a Mars deployment. Three different test configurations were investigated. In the first two configurations, the parachutes were constrained horizontally through the vent region to measure canopy breathing and wake interaction for fixed trim angles of 0 and 10 degrees from the free-stream. In the third configuration the parachute was unconstrained, permitted to trim and cone, similar to free-flight (but capsule motion is constrained), varying its alignment relative to the entry-vehicle wake. Non-intrusive test diagnostics were chosen to quantify parachute performance and provide insight into the flow field structure. An in-line loadcell provided measurement of unsteady and mean drag. Shadowgraph of the upstream parachute flow field was used to capture bow-shock motion and wake coupling. Particle image velocimetry provided first and second order flow field statistics over a planar region of the flow field, just upstream of the parachute. A photogrammetric technique was used to quantify fabric motion using multiple high speed video cameras to record

Multifunctional carbon nanotube yarns and transparent sheets: Fabrication, properties, and applications

International Nuclear Information System (INIS)

Atkinson, Ken R.; Hawkins, Stephen C.; Huynh, C.; Skourtis, Chris; Dai, Jane; Zhang Mei; Fang Shaoli; Zakhidov, Anvar A.; Lee, Sergey B.; Aliev, Ali E.; Williams, Christopher D.; Baughman, Ray H.

2007-01-01

Carbon nanotubes (CNTs) have a range of useful properties, such as high strength and modulus, high electrical and thermal conductivities, are stable at relatively high and low temperatures, and because of a low density, the specific properties are even better. For these reasons, CNTs are of great technological interest, however, difficulties in assembling the trillions of nanotubes into macro-sized objects without the use of binders has retarded the growth of practical applications. The work presented outlines efforts to develop a solid-state process for nanotube assembly that promises to eliminate the requirement to use binders and capture the inherent properties of nanotubes. These processes include spinning CNT forests into yarns having toughness and high electrical conductivity, and drawing the forests to form webs with gravimetric strengths higher than high tensile steel plate. Both yarns and webs have high electrical conductivities and can be used for emission of light by incandescence

Probe Sensor Using Nanostructured Multi-Walled Carbon Nanotube Yarn for Selective and Sensitive Detection of Dopamine

Directory of Open Access Journals (Sweden)

Wed Al-Graiti

2017-04-01

Full Text Available The demands for electrochemical sensor materials with high strength and durability in physiological conditions continue to grow and novel approaches are being enabled by the advent of new electromaterials and novel fabrication technologies. Herein, we demonstrate a probe-style electrochemical sensor using highly flexible and conductive multi-walled carbon nanotubes (MWNT yarns. The MWNT yarn-based sensors can be fabricated onto micro Pt-wire with a controlled diameter varying from 100 to 300 µm, and then further modified with Nafion via a dip-coating approach. The fabricated micro-sized sensors were characterized by electron microscopy, Raman, FTIR, electrical, and electrochemical measurements. For the first time, the MWNT/Nafion yarn-based probe sensors have been assembled and assessed for high-performance dopamine sensing, showing a significant improvement in both sensitivity and selectivity in dopamine detection in presence of ascorbic acid and uric acid. It offers the potential to be further developed as implantable probe sensors.

Parachuting from fixed objects: descriptive study of 106 fatal events in BASE jumping 1981-2006.

Science.gov (United States)

Westman, A; Rosén, M; Berggren, P; Björnstig, U

2008-06-01

To analyse the characteristics of fatal incidents in fixed object sport parachuting (building, antenna, span, earth (BASE) jumping) and create a basis for prevention. Descriptive epidemiological study. Data on reported fatal injury events (n = 106) worldwide in 1981-2006 retrieved from the BASE fatality list. Human, equipment and environmental factors. Identification of typical fatal incident and injury mechanisms for each of the four fixed object types of BASE jumping (building, antenna, span, earth). Human factors included parachutist free fall instability (loss of body control before parachute deployment), free fall acrobatics and deployment failure by the parachutist. Equipment factors included pilot chute malfunction and parachute malfunction. In cliff jumping (BASE object type E), parachute opening towards the object jumped was the most frequent equipment factor. Environmental factors included poor visibility, strong or turbulent winds, cold and water. The overall annual fatality risk for all object types during the year 2002 was estimated at about one fatality per 60 participants. Participants in BASE jumping should target risk factors with training and technical interventions. The mechanisms described in this study should be used by rescue units to improve the management of incidents.

Verification and Validation of the Spring Model Parachute Air Delivery System in Subsonic Flow

Science.gov (United States)

2015-02-27

permeability [5]. Thus the coupling of the vertical flow with the permeable and flexible fabric may have significant difference with rigid bluff bodies...Vorticity, from left to right: γ = 0, 0.25, 0.5, 0.75 of the canopies and risers . Among these parachutes, the T-10 parachute is used by the Army as a...G. F. Homicz, and A. A. Gossler, Fluid- structure coupling for lightweight flexible bodies, 17th AIAA Aerodynamic Decelerator Systems Technology

Hemp yarn reinforced composites – III. Moisture content and dimensional changes

DEFF Research Database (Denmark)

Madsen, Bo; Hoffmeyer, Preben; Lilholt, Hans

2012-01-01

Based on a comprehensive set of experimental data it is demonstrated that the moisture properties of aligned hemp fibre yarn/thermoplastic matrix composites are showing low moisture sorption capacity and low dimensional changes. Using a reference humidity of 65% RH, and a common span of ambient...

The parachute morphology as equilibrium morphology of vesicle-polymer hybrids?

NARCIS (Netherlands)

Jung, M.; Hubert, D.H.W.; Herk, van A.M.; German, A.L.

2000-01-01

Polymerisation in vesicles leads to novel polymer colloid morphologies. Two morphologies are currently reported: the triple-shell and the parachute morphology. The termodynamic analysis of these two morphologies, presented here, stresses the importance of considering interfacial energies between

32 CFR 705.32 - Aviation events and parachute demonstrations.

Science.gov (United States)

2010-07-01

... performing. What type of crowd control is planned? 5. Flight and Parachute Team demonstrations require that... the public domain is to support the recruiting aspects of the all-volunteer force concept. The... member of the public might wish to have clarified, contact Chief, Aerial Events Branch, OASD(PA), Room...

Liquid crystalline solutions of cellulose in phosphoric acid for preparing cellulose yarns

NARCIS (Netherlands)

Boerstoel, H.

2006-01-01

The presen thesis describes a new process for manufacturing high tenacity and high modulus cellulose yarns. A new direct solvent for cellulose has been discovered, leading to liquid crystalline solutions. This new solvent, superphosphoric acid, rapidly dissolves cellulose. These liquid crystalline

The study about the improvement of the quality for the fabrics made of chenille yarn

Science.gov (United States)

Hristian, L.; Ostafe, M. M.; Manea, L. R.; Leon, A. L.

2016-08-01

The work is a study about the decrease of the serious defects from the fabrics such as: the deviations from quality or the high costs, discovered and seized by customers. The analyzed fabrics have in their structures three types of different chenille yarns, such as: the Article A1 (viscose fiber with cotton, Nm 3500 dyed coil), the Article A2 (textured polyester, Nm 8000 dyed coil), the Article A3 (Trevira CS polyester, Nm 3000 the pre-dyed raw materials). The technology of chenille yarn, regardless of composition and properties is the same and is performed on the twisting machines. This study has found that the most of the flaws in the fabric, noticed by customers, are caused by the production technology of the chenille yarns. In any organization which makes goods, there are concerns about the improvement of the quality through the elimination of the nonquality. It is extremely difficult to get to “zero defects” but the first step is a systematic action plan to reduce drastically the nonconformities and the defects. The continuous improvement of the effectiveness of the integrated quality and environmental management is achieved by applying the PDCA methodology: planning, development, control, action.

Simulation of 3D parachute fluid–structure interaction based on nonlinear finite element method and preconditioning finite volume method

Directory of Open Access Journals (Sweden)

Fan Yuxin

2014-12-01

Full Text Available A fluid–structure interaction method combining a nonlinear finite element algorithm with a preconditioning finite volume method is proposed in this paper to simulate parachute transient dynamics. This method uses a three-dimensional membrane–cable fabric model to represent a parachute system at a highly folded configuration. The large shape change during parachute inflation is computed by the nonlinear Newton–Raphson iteration and the linear system equation is solved by the generalized minimal residual (GMRES method. A membrane wrinkling algorithm is also utilized to evaluate the special uniaxial tension state of membrane elements on the parachute canopy. In order to avoid large time expenses during structural nonlinear iteration, the implicit Hilber–Hughes–Taylor (HHT time integration method is employed. For the fluid dynamic simulations, the Roe and HLLC (Harten–Lax–van Leer contact scheme has been modified and extended to compute flow problems at all speeds. The lower–upper symmetric Gauss–Seidel (LU-SGS approximate factorization is applied to accelerate the numerical convergence speed. Finally, the test model of a highly folded C-9 parachute is simulated at a prescribed speed and the results show similar characteristics compared with experimental results and previous literature.

An Innovative High Fidelity Multidisciplinary Computational Framework for Parachute Inflation Dynamics

Data.gov (United States)

National Aeronautics and Space Administration — Current technology for decelerating a spacecraft from the high speed of atmospheric entry to the final stages of landing on Mars is based on parachute systems. It...

The Influence of Stabilisation on the Structure of Knits and Tensile Properties of Their Yarns

Directory of Open Access Journals (Sweden)

Rasa TREIGIENĖ

2012-12-01

Full Text Available Plated jersey knits of different composition were knitted and stabilised under hydrothermal conditions of 85 °C for 10, 20 or 30 min in steam ambience. The influence of stabilisation duration on knit structure was estimated as well as change of mechanical properties of the yarns. The obtained data show that 10 min of stabilisation influenced markedly the structure of plated jersey knits comparing with the same effect of 20 min and 30 min. The results of specific breaking force of polyester, cotton and wool yarns show decrease in their strength due to knitting and hydrothermal stabilisation processes.DOI: http://dx.doi.org/10.5755/j01.ms.18.4.3096

Sub-Scale Orion Parachute Test Results from the National Full-Scale Aerodynamics Complex 80- By 120-ft Wind Tunnel

Science.gov (United States)

Anderson, Brian P.; Greathouse, James S.; Powell, Jessica M.; Ross, James C.; Schairer, Edward T.; Kushner, Laura; Porter, Barry J.; Goulding, Patrick W., II; Zwicker, Matthew L.; Mollmann, Catherine

2017-01-01

A two-week test campaign was conducted in the National Full-Scale Aerodynamics Complex 80 x 120-ft Wind Tunnel in support of Orion parachute pendulum mitigation activities. The test gathered static aerodynamic data using an instrumented, 3-tether system attached to the parachute vent in combination with an instrumented parachute riser. Dynamic data was also gathered by releasing the tether system and measuring canopy performance using photogrammetry. Several canopy configurations were tested and compared against the current Orion parachute design to understand changes in drag performance and aerodynamic stability. These configurations included canopies with varying levels and locations of geometric porosity as well as sails with increased levels of fullness. In total, 37 runs were completed for a total of 392 data points. Immediately after the end of the testing campaign a down-select decision was made based on preliminary data to support follow-on sub-scale air drop testing. A summary of a more rigorous analysis of the test data is also presented.

Cirrus Airframe Parachute System and Odds of a Fatal Accident in Cirrus Aircraft Crashes.

Science.gov (United States)

Alaziz, Mustafa; Stolfi, Adrienne; Olson, Dean M

2017-06-01

General aviation (GA) accidents have continued to demonstrate high fatality rates. Recently, ballistic parachute recovery systems (BPRS) have been introduced as a safety feature in some GA aircraft. This study evaluates the effectiveness and associated factors of the Cirrus Airframe Parachute System (CAPS) at reducing the odds of a fatal accident in Cirrus aircraft crashes. Publicly available Cirrus aircraft crash reports were obtained from the National Transportation Safety Board (NTSB) database for the period of January 1, 2001-December 31, 2016. Accident metrics were evaluated through univariate and multivariate analyses regarding odds of a fatal accident and use of the parachute system. Included in the study were 268 accidents. For CAPS nondeployed accidents, 82 of 211 (38.9%) were fatal as compared to 8 of 57 (14.0%) for CAPS deployed accidents. After controlling for all other factors, the adjusted odds ratio for a fatal accident when CAPS was not deployed was 13.1. The substantial increased odds of a fatal accident when CAPS was not deployed demonstrated the effectiveness of CAPS at providing protection of occupants during an accident. Injuries were shifted from fatal to serious or minor with the use of CAPS and postcrash fires were significantly reduced. These results suggest that BPRS could play a significant role in the next major advance in improving GA accident survival.Alaziz M, Stolfi A, Olson DM. Cirrus Airframe Parachute System and odds of a fatal accident in Cirrus aircraft crashes. Aerosp Med Hum Perform. 2017; 88(6):556-564.

DYEING OF WOOL YARNS WITH LAURUS NOBILIS L. BERRIES

Directory of Open Access Journals (Sweden)

ERKAN Gökhan

2016-05-01

Full Text Available Nowadays natural dyes have been attracted by many researchers and firms due to demands on sustainable and nontoxic products. In this study the mature berries of bay laurel (Laurus nobilis L. were collected from trees located Kuşadası Turkey. The berries dried at 25oC and % 20-25 relative humidity. Dried berries milled and extracted with ethanol. Extracted dye was used. Three mordanting procedure (pre, meta and post mordanting and two concentrations were applied to wool yarns. Cupric sulfate, ferric sulfate, potassium dichromate and alum was used as mordant Color strength and colorimetric values were measured by Konica-Minolta 3600D spectrophotometer. Fastness to washing, perspiration and light were applied according to ISO 105C06 (A1S, ISO 105E04 and ISO 105B02 (method 2 respectively. The highest color strength (K/S value was 16.6405 and was obtained in the case of premordanting with cupric sulfate at 2 gr/L concentration. If the a* and b* values were examined, the conditions at highest color strength, the yarns had yellow color with a reddish hue. Generally, the fastness properties were moderate and good results were obtained in the case of premordanting procedure. The results show us ethanol extract of bay laurel berries can be used for dyeing of woolen products.

Grafting polymer coatings onto the surfaces of carbon nanotube forests and yarns via a photon irradiation process

Energy Technology Data Exchange (ETDEWEB)

Deng Fei; Rujisamphan, N.; Liu Chang; Ismat Shah, S.; Ni Chaoying [Department of Materials Science and Engineering, University of Delaware, Newark, Delaware 19716 (United States); Maezono, Yoshinari [Department of Project Promotion, USHIO INC., 1194, Sazuchi, Bessho-cho, Himeji Hyogo 671-0224 (Japan); Hawkins, Stephen C.; Huynh, Chi P. [Materials Science and Engineering, CSIRO, Bayview Avenue, Clayton, Victoria 3168 (Australia)

2012-05-21

Surface activation of carbon nanotubes (CNTs) as forests and yarns, depolytmerization of candidate polymers, and uniform deposition and re-polymerization onto the activated CNTs are simultaneously achieved by exposing CNTs and polymer targets to light with a narrow wavelength distribution from a vacuum ultraviolet lamp. Both polystyrene and poly (methyl methacrylate) are deposited onto the surface of CNTs in the CNT-forest and yarn in a N{sub 2} environment for 30 min during which the polymer uniformly coats the carbon nanotubes. X-ray photoelectron spectroscopy data reveal that covalent bonding occurs at the CNT-polymer interface.

Grafting polymer coatings onto the surfaces of carbon nanotube forests and yarns via a photon irradiation process

International Nuclear Information System (INIS)

Deng Fei; Rujisamphan, N.; Liu Chang; Ismat Shah, S.; Ni Chaoying; Maezono, Yoshinari; Hawkins, Stephen C.; Huynh, Chi P.

2012-01-01

Surface activation of carbon nanotubes (CNTs) as forests and yarns, depolytmerization of candidate polymers, and uniform deposition and re-polymerization onto the activated CNTs are simultaneously achieved by exposing CNTs and polymer targets to light with a narrow wavelength distribution from a vacuum ultraviolet lamp. Both polystyrene and poly (methyl methacrylate) are deposited onto the surface of CNTs in the CNT-forest and yarn in a N 2 environment for 30 min during which the polymer uniformly coats the carbon nanotubes. X-ray photoelectron spectroscopy data reveal that covalent bonding occurs at the CNT-polymer interface.

Production of Banana Fiber Yarns for Technical Textile Reinforced Composites

Directory of Open Access Journals (Sweden)

Zaida Ortega

2016-05-01

Full Text Available Natural fibers have been used as an alternative to synthetic ones for their greener character; banana fibers have the advantage of coming from an agricultural residue. Fibers have been extracted by mechanical means from banana tree pseudostems, as a strategy to valorize banana crops residues. To increase the mechanical properties of the composite, technical textiles can be used as reinforcement, instead of short fibers. To do so, fibers must be spun and woven. The aim of this paper is to show the viability of using banana fibers to obtain a yarn suitable to be woven, after an enzymatic treatment, which is more environmentally friendly. Extracted long fibers are cut to 50 mm length and then immersed into an enzymatic bath for their refining. Conditions of enzymatic treatment have been optimized to produce a textile grade of banana fibers, which have then been characterized. The optimum treating conditions were found with the use of Biopectinase K (100% related to fiber weight at 45 °C, pH 4.5 for 6 h, with bath renewal after three hours. The first spinning trials show that these fibers are suitable to be used for the production of yarns. The next step is the weaving process to obtain a technical fabric for composites production.

Airborne Priapism: A Case of Nonischemic Priapism After Military Static-Line Parachute Injury.

Science.gov (United States)

Charny, Grigory; Booms, Zachary; McDonough, Patrick; Schauer, Steven

2015-07-01

We report the case of a 21-year-old active duty U.S. Army soldier with painful and nonresolving priapism following blunt pelvic and lower extremity trauma from military static-line parachute injury during training. The patient's condition was initially managed with corporal aspiration and intracavernosal injections of phenylephrine that provided temporary relief but recurrence soon after. Referral to Urology at the site of the patient's injury yielded a diagnosis of penile hematoma. On subsequent evaluation by Urology on return to the patient's home duty station (over 96 hours after injury, with symptoms persisting), the corpora cavernosa were rigid, the corpus spongiosum was soft, and corporal blood gas drawn by the emergency department consistent with arterial blood. Penile duplex ultrasound revealed an isolated arterial-cavernosal fistula within the proximal left corporal body. The patient underwent percutaneous embolization of the fistula with successful resolution of his condition and return of normal erectile function. We discuss this unique case of high-flow priapism occurring after blunt trauma from military parachute injury and review suggested management in a stepwise fashion. The case is significant in that extensive literature review yields no previously described case of priapism following trauma from military parachute injury. Reprint & Copyright © 2015 Association of Military Surgeons of the U.S.

Effect of ecological surface treatment method on friction strength properties of nettle (urtica dioica) fibre yarns

Science.gov (United States)

Şansal, S.; Mıstık, S. I.; Fettahov, R.; Ovalı, S.; Duman, M.

2017-10-01

Over the last few decades, more attention is given to lignocellulose based fibres as reinforcement material in the polymer composites owing to the environmental pollution caused by the extensive usage of synthetic and inorganic fibres. Developing new natural fibre reinforced composites is the focus of many researches nowadays. They are made from renewable resources and they have less environmental effect in comparison to inorganic fibre reinforced composites. The interest of consumers in eco-friendly natural fibres and textiles has increased in recent years. Unlike inorganic fibres, natural fibres present light weight, high strength/density ratio and are readily available, environmentally friendly and biodegradable. Many different types of natural fibres are exploited for the production of biodegradable polymer composites. The nettle (Urtica dioica L.) is a well-known plant growing on rural sites of Europe, Asia, and North America. Nettle plant contains fibre similar to hemp and flax. However, similar to other natural fibres, nettle fibres are poorly compatible with the thermoplastic matrix of composites, due to their hydrophilic character which reduces mechanical properties of nettle fibre reinforced thermoplastics. In order to improve the fibrematrix adhesion of the natural fibre reinforced composites, surface treatment processes are applied to the lignocellulose fibres. In this study nettle (urtica dioica) fibre yarns were treated with NaOH by using conventional, ultrasonic and microwave energy methods. After treatment processes tensile strength, elongation, friction strength and SEM observations of the nettle fibre yarns were investigated. All treatment processes were improved the tensile strength, elongation and friction strength properties of the nettle fibre yarns. Also higher tensile strength, elongation and friction strength properties were obtained from treated nettle fibre yarns which treated by using microwave energy method.

Hybrid nanomembranes for high power and high energy density supercapacitors and their yarn application.

Science.gov (United States)

Lee, Jae Ah; Shin, Min Kyoon; Kim, Shi Hyeong; Kim, Seon Jeong; Spinks, Geoffrey M; Wallace, Gordon G; Ovalle-Robles, Raquel; Lima, Márcio D; Kozlov, Mikhail E; Baughman, Ray H

2012-01-24

We report mechanically robust, electrically conductive, free-standing, and transparent hybrid nanomembranes made of densified carbon nanotube sheets that were coated with poly(3,4-ethylenedioxythiophene) using vapor phase polymerization and their performance as supercapacitors. The hybrid nanomembranes with thickness of ~66 nm and low areal density of ~15 μg/cm(2)exhibited high mechanical strength and modulus of 135 MPa and 12.6 GPa, respectively. They also had remarkable shape recovery ability in liquid and at the liquid/air interface unlike previous carbon nanotube sheets. The hybrid nanomembrane attached on a current collector had volumetric capacitance of ~40 F/cm(3) at 100 V s(-1) (~40 and ~80 times larger than that of onion-like carbon measured at 100 V s(-1) and activated carbon measured at 20 V s(-1), respectively), and it showed rectangular shapes of cyclic voltammograms up to ~5 V s(-1). High mechanical strength and flexibility of the hybrid nanomembrane enabled twisting it into microsupercapacitor yarns with diameters of ~30 μm. The yarn supercapacitor showed stable cycling performance without a metal current collector, and its capacitance decrease was only ~6% after 5000 cycles. Volumetric energy and power density of the hybrid nanomembrane was ~70 mWh cm(-3) and ~7910 W cm(-3), and the yarn possessed the energy and power density of ~47 mWh cm(-3) and ~538 W cm(-3). © 2011 American Chemical Society

PROCESSING AND ANALYSIS OF Fligh experiment DATA FOR DETERMINING THE CHARACTERISTICS OF THE MOTION OF A ROUND PARACHUTE on a spiral trajectory AT HIGH ALTITUDES

Directory of Open Access Journals (Sweden)

S. V. Zhurin

2015-01-01

Full Text Available The article is addressed to the analysis of the trajectory parameters and videos obtained during the flight experiment at the launch of meteo-rocket MMP-06 with the purpose to determine major parameters of motion of a round parachute at subsonic speeds in the range of altitudes from 0 to 40 km. The data analysis showed that the trajectory of the parachute represents spiral "stretched" by the wind in the horizontal direction and disturbed by random factors of a non-stationary flow around the parachute. The main parameters of the trajectory are obtained according to the experimental data. Only qualitative analysis of spiral motion paths for round parachutes may be found in the publications on parachute subjects. This article presents the quantitative characteristics of this process.

PROCESSING AND ANALYSIS OF DATA OF natural experiment FOR DETERMINING THE tragectory CHARACTERISTICS OF A ROUND PARACHUTE AT HIGH ALTITUDES

Directory of Open Access Journals (Sweden)

S. V. Zhurin

2015-01-01

Full Text Available The article is devoted to the analysis of the trajectory parameters obtained during the flight experiment at the start of meteo-rocket MMP-06, to determine major parameters of motion of a round parachute at subsonic speeds in the range of altitudes from 0 to 60 km. The Reynolds number is changed in the range from 104 to1,5·106.The main parameters of the trajectory were obtained according to the experimental data. Only laboratory research on a model parachute systems in such a wide range of Reynolds numbers are found in the literature on parachute subjects. This article obtained results of flight experiment.

Tensile strength of woven yarn kenaf fiber reinforced polyester composites

OpenAIRE

A.E. Ismail; M.A. Che Abdul Aziz

2015-01-01

This paper presents the tensile strength of woven kenaf fiber reinforced polyester composites. The as-received yarn kenaf fiber is weaved and then aligned into specific fiber orientations before it is hardened with polyester resin. The composite plates are shaped according to the standard geometry and uni-axially loaded in order to investigate the tensile responses. Two important parameters are studied such as fiber orientations and number of layers. According to the results, it is shown that...

Thermal conductivity of high performance carbon nanotube yarn-like fibers

Energy Technology Data Exchange (ETDEWEB)

Mayhew, Eric; Prakash, Vikas, E-mail: vikas.prakash@case.edu [Department of Mechanical and Aerospace Engineering, Case Western Reserve University, Cleveland, Ohio 44106-7222 (United States)

2014-05-07

In the present paper, we present results of thermal conductivity measurements in free standing carbon nanotube (CNT) yarn-like fibers. The measurements are made using a T-type experimental configuration utilizing a Wollaston-wire hot probe inside a scanning electron microscope. In this technique, a suspended platinum wire is used both as a heater and a thermal sensor. A low frequency alternating current source is used to heat the probe wire while the third harmonic voltage across the wire is measured by a lock-in amplifier. The conductivity is deduced from an analytical model that relates the drop in the spatially averaged temperature of the wire to that of the sample. The average thermal conductivity of the neat CNT fibers and the CNT –polymer composite fibers is found to be 448 W/m-K and 225 W/m-K, respectively. These values for conductivity are amongst the highest measured for CNT yarn-like fibers fabricated using a dry spinning process from vertically aligned CNT arrays. The enhancement in thermal conductivity is understood to be due to an increase in the CNT fiber elastic stiffness during the draw and twist operations, lower CNT thermal contact resistance due to increase in CNT contact area, and better alignment of the CNT fibrils along the length of the fiber.

MXene: a potential candidate for yarn supercapacitors.

Science.gov (United States)

Zhang, Jizhen; Seyedin, Shayan; Gu, Zhoujie; Yang, Wenrong; Wang, Xungai; Razal, Joselito M

2017-12-07

The increasing developments in wearable electronics demand compatible power sources such as yarn supercapacitors (YSCs) that can effectively perform in a limited footprint. MXene nanosheets, which have been recently shown in the literature to possess ultra-high volumetric capacitance, were used in this study for the fabrication of YSCs in order to identify their potential merit and performance in YSCs. With the aid of a conductive binder (PEDOT-PSS), YSCs with high mass loading of MXene are demonstrated. These MXene-based YSCs exhibit excellent device performance and stability even under bending and twisting. This study demonstrates that MXene is a promising candidate for YSCs and its further development can lead to flexible power sources with sufficient performance for powering miniaturized and/or wearable electronics.

SUSI 62 A ROBUST AND SAFE PARACHUTE UAV WITH LONG FLIGHT TIME AND GOOD PAYLOAD

Directory of Open Access Journals (Sweden)

H. P. Thamm

2012-09-01

Full Text Available In many research areas in the geo-sciences (erosion, land use, land cover change, etc. or applications (e.g. forest management, mining, land management etc. there is a demand for remote sensing images of a very high spatial and temporal resolution. Due to the high costs of classic aerial photo campaigns, the use of a UAV is a promising option for obtaining the desired remote sensed information at the time it is needed. However, the UAV must be easy to operate, safe, robust and should have a high payload and long flight time. For that purpose, the parachute UAV SUSI 62 was developed. It consists of a steel frame with a powerful 62 cm3 2- stroke engine and a parachute wing. The frame can be easily disassembled for transportation or to replace parts. On the frame there is a gimbal mounted sensor carrier where different sensors, standard SLR cameras and/or multi-spectral and thermal sensors can be mounted. Due to the design of the parachute, the SUSI 62 is very easy to control. Two different parachute sizes are available for different wind speed conditions. The SUSI 62 has a payload of up to 8 kg providing options to use different sensors at the same time or to extend flight duration. The SUSI 62 needs a runway of between 10 m and 50 m, depending on the wind conditions. The maximum flight speed is approximately 50 km/h. It can be operated in a wind speed of up to 6 m/s. The design of the system utilising a parachute UAV makes it comparatively safe as a failure of the electronics or the remote control only results in the UAV coming to the ground at a slow speed. The video signal from the camera, the GPS coordinates and other flight parameters are transmitted to the ground station in real time. An autopilot is available, which guarantees that the area of investigation is covered at the desired resolution and overlap. The robustly designed SUSI 62 has been used successfully in Europe, Africa and Australia for scientific projects and also for

Rapid Simulation of Flat Knitting Loops Based On the Yarn Texture and Loop Geometrical Model

Directory of Open Access Journals (Sweden)

Lu Zhiwen

2017-06-01

Full Text Available In order to create realistic loop primitives suitable for the fast computer-aided design (CAD of the flat knitted fabric, we have a research on the geometric model of the loop as well as the variation of the loop surface. Establish the texture variation model based on the changing process from the normal yarn to loop that provides the realistic texture of the simulative loop. Then optimize the simulative loop based on illumination variation. This paper develops the computer program with the optimization algorithm and achieves the loop simulation of different yarns to verify the feasibility of the proposed algorithm. Our work provides a fast CAD of the flat knitted fabric with loop simulation, and it is not only more realistic but also material adjustable. Meanwhile it also provides theoretical value for the flat knitted fabric computer simulation.

The effect of z-binding yarns on the electrical properties of 3D woven composites

KAUST Repository

Saleh, Mohamed Nasr; Yudhanto, Arief; Lubineau, Gilles; Soutis, Constantinos

2017-01-01

Electrical resistance monitoring (ERM) has been used to study the effect of the z-binding yarns on the initial electrical resistance (ER) and its change of three architectures of 3D woven carbon fibre composites namely (orthogonal “ORT”, layer

Method for Forming Pulp Fibre Yarns Developed by a Design-driven Process

Directory of Open Access Journals (Sweden)

Tiia-Maria Tenhunen

2016-01-01

Full Text Available A simple and inexpensive method for producing water-stable pulp fibre yarns using a deep eutectic mixture composed of choline chloride and urea (ChCl/urea was developed in this work. Deep eutectic solvents (DESs are eutectic mixtures consisting of two or more components that together have a lower melting point than the individual components. DESs have been previously studied with respect to cellulose dissolution, functionalisation, and pre-treatment. This new method uses a mixture of choline chloride and urea, which is used as a swelling and dispersing agent for the pulp fibres in the yarn-forming process. Although the pulp seemed to form a gel when dispersed in ChCl/urea, the ultrastructure of the pulp was not affected. To enable water stability, pulp fibres were crosslinked by esterification using polyacrylic acid. ChCl/urea could be easily recycled and reused by distillation. The novel process described in this study enables utilisation of pulp fibres in textile production without modification or dissolution and shortening of the textile value chain. An interdisciplinary approach was used, where potential applications were explored simultaneously with material development from process development to the early phase prototyping.

The Influence of Disorder in Multifilament Yarns on the Bond Performance in Textile Reinforced Concrete

Directory of Open Access Journals (Sweden)

M. Konrad

2004-01-01

Full Text Available In this paper we analyze the performance of a bond layer between the multi-filament yarn and the cementitious matrix. The performance of the bond layer is a central issue in the development of textile-reinforced concrete. The changes in the microstructure during the loading result in distinguished failure mechanisms on the micro, meso and macro scales. The paper provides a brief review of these effects and describes a modeling strategy capable of reflecting the failure process. Using the model of the bond layer we illuminate the correspondence between the disorder in the microstructure of the yarn and the bonding behavior at the meso- and macro level. Particular interest is paid to the influence of irregularities in the micro-structure (relative differences in filament lengths, varying bond quality, bond-free length for different levels of local bond quality between the filament surface and the matrix. 

The PARAChute Project: Remote Monitoring of Posture and Gait for Fall Prevention

Science.gov (United States)

Hewson, David J.; Duchêne, Jacques; Charpillet, François; Saboune, Jamal; Michel-Pellegrino, Valérie; Amoud, Hassan; Doussot, Michel; Paysant, Jean; Boyer, Anne; Hogrel, Jean-Yves

2007-12-01

Falls in the elderly are a major public health problem due to both their frequency and their medical and social consequences. In France alone, more than two million people aged over 65 years old fall each year, leading to more than 9 000 deaths, in particular in those over 75 years old (more than 8 000 deaths). This paper describes the PARAChute project, which aims to develop a methodology that will enable the detection of an increased risk of falling in community-dwelling elderly. The methods used for a remote noninvasive assessment for static and dynamic balance assessments and gait analysis are described. The final result of the project has been the development of an algorithm for movement detection during gait and a balance signature extracted from a force plate. A multicentre longitudinal evaluation of balance has commenced in order to validate the methodologies and technologies developed in the project.

Environmental effect on the mechanical properties of commingled-yarn-based carbon fibre/polyamide 6 composites

DEFF Research Database (Denmark)

Raghavalu Thirumalai, Durai Prabhakaran; Toftegaard, Helmuth Langmaack

2014-01-01

The main objective of this experimental investigation was to evaluate the changes from accelerated ageing on selected properties of carbon fibre/polyamide 6 composites based on hybrid yarns. In this study, two types of mechanical tests were performed to measure the environmental influence...... on the material properties. They are three-point bending to measure the flexural strength and stiffness, and short beam three-point bending to measure the interlaminar shear strength. The 10-mm-thick quasi-isotropic carbon fibre/polyamide 6 composites with 52% volume fraction of carbon fibre to be tested were...... temperature. The interlaminar shear strength values also drop to about 75% at both −45 and 115. Extreme temperatures and long-time exposure to humidity of quasi-isotropic carbon fibre/polyamide 6 laminates can thus reduce the bending stiffness and strength by up to 35% and the interlaminar shear strength...

Development of sugar palm yarn/glass fibre reinforced unsaturated polyester hybrid composites

Science.gov (United States)

Nurazzi, N. Mohd; Khalina, A.; Sapuan, S. Mohd; Rahmah, M.

2018-04-01

This study investigates the effect of fibre hybridization for sugar palm yarn fibre with glass fibre reinforced with unsaturated polyester composites. In this work, unsaturated polyester resin are reinforced with fibre at a ratio of 70:30 wt% and 60:40 wt%. The hybrid composites were characterized in terms of physical (density and water absorption), mechanical (tensile, flexural and compression) and thermal properties through thermal gravimetry analysis (TGA). Density determination showed that density increased with higher wt% of glass fibre. The inherently higher density of glass fibre increased the density of hybrid composite. Resistance to water absorption is improved upon the incorporation of glass fibre and the hybrid composites were found to reach equilibrium absorption at days 4 and 5. As for mechanical performance, the highest tensile strength, tensile modulus, flexural strength, flexural modulus and compression strength were obtained from 40 wt% of fibres reinforcement with ratio of 50:50 wt% of sugar palm yarn fibre and glass fibre reinforced unsaturated polyester composites. The increase of glass fibre loading had a synergistic effect on the mechanical properties to the composites structure due to its superior strength and modulus. The thermal stability of hybrid composites was improved by the increase of onset temperature and the reduction of residues upon increase in temperature.

Fabrication and preliminary study of a biomimetic tri-layer tubular graft based on fibers and fiber yarns for vascular tissue engineering.

Science.gov (United States)

Wu, Tong; Zhang, Jialing; Wang, Yuanfei; Li, Dandan; Sun, Binbin; El-Hamshary, Hany; Yin, Meng; Mo, Xiumei

2018-01-01

Designing a biomimetic and functional tissue-engineered vascular graft has been urgently needed for repairing and regenerating defected vascular tissues. Utilizing a multi-layered vascular scaffold is commonly considered an effective way, because multi-layered scaffolds can easily simulate the structure and function of natural blood vessels. Herein, we developed a novel tri-layer tubular graft consisted of Poly(L-lactide-co-caprolactone)/collagen (PLCL/COL) fibers and Poly(lactide-co-glycolide)/silk fibroin (PLGA/SF) yarns via a three-step electrospinning method. The tri-layer vascular graft consisted of PLCL/COL aligned fibers in inner layer, PLGA/SF yarns in middle layer, and PLCL/COL random fibers in outer layer. Each layer possessed tensile mechanical strength and elongation, and the entire tubular structure provided tensile and compressive supports. Furthermore, the human umbilical vein endothelial cells (HUVECs) and smooth muscle cells (SMCs) proliferated well on the materials. Fluorescence staining images demonstrated that the axially aligned PLCL/COL fibers prearranged endothelium morphology in lumen and the circumferential oriented PLGA/SF yarns regulated SMCs organization along the single yarns. The outside PLCL/COL random fibers performed as the fixed layer to hold the entire tubular structure. The in vivo results showed that the tri-layer vascular graft supported cell infiltration, scaffold biodegradation and abundant collagen production after subcutaneous implantation for 10weeks, revealing the optimal biocompatibility and tissue regenerative capability of the tri-layer graft. Therefore, the specially designed tri-layer vascular graft will be beneficial to vascular reconstruction. Copyright © 2017. Published by Elsevier B.V.

A roentgenographic method for the appraisal of a quantitative composition of blend yarns

International Nuclear Information System (INIS)

Wlochowicz, A.; Bozek, B.

1980-01-01

The suitability of a roentgenographic method for the determination of per cent composition in a blend the yarn was spun of is analysed. Results were compared to the chemical test. It has been found that as far as a composition of the blend is concerned, the X-ray method might replace the chemical one, however, the appraisal of the blending effect appears unsatisfactory. (M.Z.)

The effects of growth conditions and of processing into yarn on dislocations in hemp fibres

DEFF Research Database (Denmark)

Thygesen, Lisbeth Garbrecht

2011-01-01

at harvest in hemp fibres from plants grown in a green house under three different regimes (wind free, windy and dry) with the percentage found in commercial hemp yarn. As expected a higher percentage of the cell wall consisted of dislocations in the processed fibres, but the increase was only significant...

The PARAChute Project: Remote Monitoring of Posture and Gait for Fall Prevention

Directory of Open Access Journals (Sweden)

Anne Boyer

2007-01-01

Full Text Available Falls in the elderly are a major public health problem due to both their frequency and their medical and social consequences. In France alone, more than two million people aged over 65 years old fall each year, leading to more than 9 000 deaths, in particular in those over 75 years old (more than 8 000 deaths. This paper describes the PARAChute project, which aims to develop a methodology that will enable the detection of an increased risk of falling in community-dwelling elderly. The methods used for a remote noninvasive assessment for static and dynamic balance assessments and gait analysis are described. The final result of the project has been the development of an algorithm for movement detection during gait and a balance signature extracted from a force plate. A multicentre longitudinal evaluation of balance has commenced in order to validate the methodologies and technologies developed in the project.

Nano-yarn carbon nanotube fiber based enzymatic glucose biosensor

International Nuclear Information System (INIS)

Zhu Zhigang; Burugapalli, Krishna; Moussy, Francis; Song, Wenhui; Li Yali; Zhong Xiaohua

2010-01-01

A novel brush-like electrode based on carbon nanotube (CNT) nano-yarn fiber has been designed for electrochemical biosensor applications and its efficacy as an enzymatic glucose biosensor demonstrated. The CNT nano-yarn fiber was spun directly from a chemical-vapor-deposition (CVD) gas flow reaction using a mixture of ethanol and acetone as the carbon source and an iron nano-catalyst. The fiber, 28 μm in diameter, was made of bundles of double walled CNTs (DWNTs) concentrically compacted into multiple layers forming a nano-porous network structure. Cyclic voltammetry study revealed a superior electrocatalytic activity for CNT fiber compared to the traditional Pt-Ir coil electrode. The electrode end tip of the CNT fiber was freeze-fractured to obtain a unique brush-like nano-structure resembling a scale-down electrical 'flex', where glucose oxidase (GOx) enzyme was immobilized using glutaraldehyde crosslinking in the presence of bovine serum albumin (BSA). An outer epoxy-polyurethane (EPU) layer was used as semi-permeable membrane. The sensor function was tested against a standard reference electrode. The sensitivities, linear detection range and linearity for detecting glucose for the miniature CNT fiber electrode were better than that reported for a Pt-Ir coil electrode. Thermal annealing of the CNT fiber at 250 deg. C for 30 min prior to fabrication of the sensor resulted in a 7.5 fold increase in glucose sensitivity. The as-spun CNT fiber based glucose biosensor was shown to be stable for up to 70 days. In addition, gold coating of the electrode connecting end of the CNT fiber resulted in extending the glucose detection limit to 25 μM. To conclude, superior efficiency of CNT fiber for glucose biosensing was demonstrated compared to a traditional Pt-Ir sensor.

Nano-yarn carbon nanotube fiber based enzymatic glucose biosensor

Science.gov (United States)

Zhu, Zhigang; Song, Wenhui; Burugapalli, Krishna; Moussy, Francis; Li, Ya-Li; Zhong, Xiao-Hua

2010-04-01

A novel brush-like electrode based on carbon nanotube (CNT) nano-yarn fiber has been designed for electrochemical biosensor applications and its efficacy as an enzymatic glucose biosensor demonstrated. The CNT nano-yarn fiber was spun directly from a chemical-vapor-deposition (CVD) gas flow reaction using a mixture of ethanol and acetone as the carbon source and an iron nano-catalyst. The fiber, 28 µm in diameter, was made of bundles of double walled CNTs (DWNTs) concentrically compacted into multiple layers forming a nano-porous network structure. Cyclic voltammetry study revealed a superior electrocatalytic activity for CNT fiber compared to the traditional Pt-Ir coil electrode. The electrode end tip of the CNT fiber was freeze-fractured to obtain a unique brush-like nano-structure resembling a scale-down electrical 'flex', where glucose oxidase (GOx) enzyme was immobilized using glutaraldehyde crosslinking in the presence of bovine serum albumin (BSA). An outer epoxy-polyurethane (EPU) layer was used as semi-permeable membrane. The sensor function was tested against a standard reference electrode. The sensitivities, linear detection range and linearity for detecting glucose for the miniature CNT fiber electrode were better than that reported for a Pt-Ir coil electrode. Thermal annealing of the CNT fiber at 250 °C for 30 min prior to fabrication of the sensor resulted in a 7.5 fold increase in glucose sensitivity. The as-spun CNT fiber based glucose biosensor was shown to be stable for up to 70 days. In addition, gold coating of the electrode connecting end of the CNT fiber resulted in extending the glucose detection limit to 25 µM. To conclude, superior efficiency of CNT fiber for glucose biosensing was demonstrated compared to a traditional Pt-Ir sensor.

Lean six sigma implementation in a yarn textile industry

Directory of Open Access Journals (Sweden)

Rayra Rodrigues Nogueira

2017-06-01

Full Text Available Due to fierce competition from companies in achieving larger market share, there is an increasing interest regarding cost reduction, efficiency in business and processes, increase in quality and continuous improvement. Given these situations, companies are adopting some practices which seek to improve their strategies, increase understanding of the needs of their customers and promote business growth, the Lean Manufacturing and Six Sigma programs were adopted in order to enable businesses to succeed in achieving continuous improvement in their business. This paper presents a case study of a textile yarn industry which, in order to increase the sales of the business and the elimination of waste, used the methodology of Lean Six Sigma Program based on DMAIC method to assist in achieving these goals.

Extrapolating the Trends of Test Drop Data with Opening Shock Factor Calculations: the Case of the Orion Main and Drogue Parachutes Inflating to 1st Reefed Stage

Science.gov (United States)

Potvin, Jean; Ray, Eric

2017-01-01

We describe a new calculation of the opening shock factor C (sub k) characterizing the inflation performance of NASA's Orion spacecraft main and drogue parachutes opening under a reefing constraint (1st stage reefing), as currently tested in the Capsule Parachute Assembly System (CPAS) program. This calculation is based on an application of the Momentum-Impulse Theorem at low mass ratio (R (sub m) is less than 10 (sup -1)) and on an earlier analysis of the opening performance of drogues decelerating point masses and inflating along horizontal trajectories. Herein we extend the reach of the Theorem to include the effects of payload drag and gravitational impulse during near-vertical motion - both important pre-requisites for CPAS parachute analysis. The result is a family of C (sub k) versus R (sub m) curves which can be used for extrapolating beyond the drop-tested envelope. The paper proves this claim in the case of the CPAS Mains and Drogues opening while trailing either a Parachute Compartment Drop Test Vehicle or a Parachute Test Vehicle (an Orion capsule boiler plate). It is seen that in all cases the values of the opening shock factor can be extrapolated over a range in mass ratio that is at least twice that of the test drop data.

Development of hybrid cotton/hydrogel yarns with improved absorption properties for biomedical applications

Energy Technology Data Exchange (ETDEWEB)

Pollini, Mauro; Paladini, Federica, E-mail: federica.paladini@unisalento.it; Sannino, Alessandro; Maffezzoli, Alfonso

2016-06-01

Hyperhidrosis, or excessive sweating, is an overlooked and potentially disabling symptom, which is often seen in social anxiety disorder. In this work an innovative advanced textile material was developed for application in the management of excessive sweating, preparing a drying yarn providing improved comfort. Hybrid cotton/hydrogel yarns were obtained by combining cotton with superabsorbent hydrogels through an optimization study focused on the achievement of the most promising product in terms of absorption properties and resistance to washings. Swelling and washing tests were performed using different hydrogels, and the effect of an additional crosslinking on the materials was also evaluated by testing different solutions containing Al{sup 3+} and Ca{sup 2+} ions. Scanning electron microscopy and infrared spectroscopy analyses were adopted to characterize morphology and chemical structure of the hydrogels undergoing different production processes. The biocompatibility of the hybrid fabrics was demonstrated by 3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyltetrazolium bromide colorimetric assay (MTT) through the extract method. - Highlights: • Novel textile based on natural fibres and superabsorbent hydrogels was developed. • The swelling ratio and the durability to washings were evaluated. • The effect of the choice of the hydrogel was studied. • The effects of additional crosslinking on hydrogel and fabrics were evaluated. • The optimized parameters determined durable and improved absorption properties.

Structures and Properties of Polyacrylonitrile/Graphene Composite Nanofiber Yarns Prepared by Multi-Needle Electrospinning Device with an Auxiliary Electrode.

Science.gov (United States)

Yan, Tao; Pan, Zhi-Juan

2018-06-01

In this paper, polyacrylonitrile/graphene composite nanofiber filaments were manufactured continuously by a homemade eight-needle electrospinning device with an auxiliary electrode. The polyacrylonitrile/graphene composite nanofiber yarns were obtained continuously by plying and twisting the composite nanofiber filaments. The structures and properties of the composite nanofiber filaments with different GP mass fractions and yarns were investigated. The results demonstrated that the maximum alignment degree of the composite nanofibers along the filament axis could reach 74.3% with 1%, and the alignment degree decreased with increasing graphene mass fraction. The diameters of the composite nanofibers were considerably smaller than those of the pure polyacrylonitrile nanofiber, and the minimum diameter was 156 nm for 1%. The conductivity of the composite nanofiber filaments was significantly enhanced by seven orders of magnitude compared with that of the pure polyacrylonitrile nanofiber filament, and the maximum value was 3.73×10-7 S/cm for 1.5%. Due to graphene agglomeration, the conductivity decreased when the mass fraction was more than 1.5%. The different number of filaments and twists were examined in detail to improve the poor mechanical properties of the nanofiber filaments. With an increase in twists, the breaking stress and strain increased initially and later decreased, and the maximum breaking stress and strain were 16.54 MPa and 26.42%, respectively. This study demonstrates the possibility of continuously and stably manufacturing polyacrylonitrile/graphene composite nanofiber yarns.

Fabric Weave Pattern and Yarn Color Recognition and Classification Using a Deep ELM Network

Directory of Open Access Journals (Sweden)

Babar Khan

2017-10-01

Full Text Available Usually, a fabric weave pattern is recognized using methods which identify the warp floats and weft floats. Although these methods perform well for uniform or repetitive weave patterns, in the case of complex weave patterns, these methods become computationally complex and the classification error rates are comparatively higher. Furthermore, the fault-tolerance (invariance and stability (selectivity of the existing methods are still to be enhanced. We present a novel biologically-inspired method to invariantly recognize the fabric weave pattern (fabric texture and yarn color from the color image input. We proposed a model in which the fabric weave pattern descriptor is based on the HMAX model for computer vision inspired by the hierarchy in the visual cortex, the color descriptor is based on the opponent color channel inspired by the classical opponent color theory of human vision, and the classification stage is composed of a multi-layer (deep extreme learning machine. Since the weave pattern descriptor, yarn color descriptor, and the classification stage are all biologically inspired, we propose a method which is completely biologically plausible. The classification performance of the proposed algorithm indicates that the biologically-inspired computer-aided-vision models might provide accurate, fast, reliable and cost-effective solution to industrial automation.

PREDICTING DEMAND FOR COTTON YARNS

Directory of Open Access Journals (Sweden)

SALAS-MOLINA Francisco

2017-05-01

Full Text Available Predicting demand for fashion products is crucial for textile manufacturers. In an attempt to both avoid out-of-stocks and minimize holding costs, different forecasting techniques are used by production managers. Both linear and non-linear time-series analysis techniques are suitable options for forecasting purposes. However, demand for fashion products presents a number of particular characteristics such as short life-cycles, short selling seasons, high impulse purchasing, high volatility, low predictability, tremendous product variety and a high number of stock-keeping-units. In this paper, we focus on predicting demand for cotton yarns using a non-linear forecasting technique that has been fruitfully used in many areas, namely, random forests. To this end, we first identify a number of explanatory variables to be used as a key input to forecasting using random forests. We consider explanatory variables usually labeled either as causal variables, when some correlation is expected between them and the forecasted variable, or as time-series features, when extracted from time-related attributes such as seasonality. Next, we evaluate the predictive power of each variable by means of out-of-sample accuracy measurement. We experiment on a real data set from a textile company in Spain. The numerical results show that simple time-series features present more predictive ability than other more sophisticated explanatory variables.

Cross-linking multiwall carbon nanotubes using PFPA to build robust, flexible and highly aligned large-scale sheets and yarns

Czech Academy of Sciences Publication Activity Database

Inoue, Y.; Nakamura, K.; Miyasaka, Y.; Nakano, T.; Kletetschka, Günther

2016-01-01

Roč. 27, č. 11 (2016) ISSN 0957-4484 Institutional support: RVO:67985831 Keywords : multi-walled carbon nanotube * nano-mechanical properties * cross-linking * PFPA * dry spinning * yarn Subject RIV: BN - Astronomy, Celestial Mechanics, Astrophysics Impact factor: 3.440, year: 2016

Development of a Smart Release Algorithm for Mid-Air Separation of Parachute Test Articles

Science.gov (United States)

Moore, James W.

2011-01-01

The Crew Exploration Vehicle Parachute Assembly System (CPAS) project is currently developing an autonomous method to separate a capsule-shaped parachute test vehicle from an air-drop platform for use in the test program to develop and validate the parachute system for the Orion spacecraft. The CPAS project seeks to perform air-drop tests of an Orion-like boilerplate capsule. Delivery of the boilerplate capsule to the test condition has proven to be a critical and complicated task. In the current concept, the boilerplate vehicle is extracted from an aircraft on top of a Type V pallet and then separated from the pallet in mid-air. The attitude of the vehicles at separation is critical to avoiding re-contact and successfully deploying the boilerplate into a heatshield-down orientation. Neither the pallet nor the boilerplate has an active control system. However, the attitude of the mated vehicle as a function of time is somewhat predictable. CPAS engineers have designed an avionics system to monitor the attitude of the mated vehicle as it is extracted from the aircraft and command a release when the desired conditions are met. The algorithm includes contingency capabilities designed to release the test vehicle before undesirable orientations occur. The algorithm was verified with simulation and ground testing. The pre-flight development and testing is discussed and limitations of ground testing are noted. The CPAS project performed a series of three drop tests as a proof-of-concept of the release technique. These tests helped to refine the attitude instrumentation and software algorithm to be used on future tests. The drop tests are described in detail and the evolution of the release system with each test is described.

75 FR 11559 - Certain Combed Cotton Yarns: Effect of Modification of U.S.-Bahrain FTA Rules of Origin

Science.gov (United States)

2010-03-11

... INTERNATIONAL TRADE COMMISSION [Investigation No. Bahrain-FTA-103-025] Certain Combed Cotton Yarns: Effect of Modification of U.S.- Bahrain FTA Rules of Origin AGENCY: United States International Trade... to section 104 of the United States-Bahrain Free Trade Agreement (FTA) Implementation Act (19 U.S.C...

Design of Novel Wearable, Stretchable, and Waterproof Cable-Type Supercapacitors Based on High-Performance Nickel Cobalt Sulfide-Coated Etching-Annealed Yarn Electrodes.

Science.gov (United States)

Chen, Yuejiao; Xu, Bingang; Wen, Jianfeng; Gong, Jianliang; Hua, Tao; Kan, Chi-Wai; Deng, Jiwei

2018-04-19

Rapid advances in functional electronics bring tremendous demands on innovation toward effective designs of device structures. Yarn supercapacitors (SCs) show advantages of flexibility, knittability, and small size, and can be integrated into various electronic devices with low cost and high efficiency for energy storage. In this work, functionalized stainless steel yarns are developed to support active materials of positive and negative electrodes, which not only enhance capacitance of both electrodes but can also be designed into stretchable configurations. The as-made asymmetric yarn SCs show a high energy density of 0.0487 mWh cm -2 (10.19 mWh cm -3 ) at a power density of 0.553 mW cm -2 (129.1 mW cm -3 ) and a specific capacitance of 127.2 mF cm -2 under an operating voltage window of 1.7 V. The fabricated SC is then made into a stretchable configuration by a prestraining-then-releasing approach using polydimethylsiloxane (PDMS) tube, and its electrochemical performance can be well maintained when stretching up to a high strain of 100%. Moreover, the stretchable cable-type SCs are stably workable under water-immersed condition. The method opens up new ways for fabricating flexible, stretchable, and waterproof devices. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Why Clothes Don't Fall Apart: Tension Transmission in Staple Yarns

Science.gov (United States)

Warren, Patrick B.; Ball, Robin C.; Goldstein, Raymond E.

2018-04-01

The problem of how staple yarns transmit tension is addressed within abstract models in which the Amontons-Coulomb friction laws yield a linear programing (LP) problem for the tensions in the fiber elements. We find there is a percolation transition such that above the percolation threshold the transmitted tension is in principle unbounded. We determine that the mean slack in the LP constraints is a suitable order parameter to characterize this supercritical state. We argue the mechanism is generic, and in practical terms, it corresponds to a switch from a ductile to a brittle failure mode accompanied by a significant increase in mechanical strength.

Wind tunnel tests of modified cross, hemisflo, and disk-gap-band parachutes with emphasis in the transonic range

Science.gov (United States)

Foughner, J. T., Jr.; Alexander, W. C.

1974-01-01

Transonic wind-tunnel studies were conducted with modified cross, hemisflo, and disk-gap-band parachute models in the wake of a cone-cylinder shape forebody. The basic cross design was modified with the addition of a circumferential constraining band at the lower edge of the canopy panels. The tests covered a Mach number range of 0.3 to 1.2 and a dynamic pressure range from 479 Newtons per square meter to 5746 Newtons per square meter. The parachute models were flexible textile-type structures and were tethered to a rigid forebody with a single flexible riser. Different size models of the modified cross and disk-gap-band canopies were tested to evaluate scale effects. Model reference diameters were 0.30, 0.61, and 1.07 meters (1.0, 2.0, and 3.5 ft) for the modified cross; and nominal diameters of 0.25 and 0.52 meter (0.83 and 1.7 ft) for the disk-gap-band; and 0.55 meter (1.8 ft) for the hemisflo. Reefing information is presented for the 0.61-meter-diameter cross and the 0.52-meter-diameter disk-gap-band. Results are presented in the form of the variation of steady-state average drag coefficient with Mach number. General stability characteristics of each parachute are discussed. Included are comments on canopy coning, spinning, and fluttering motions.

Investigation on Shielding and Mechanical Behavior of Carbon/Stainless Steel Hybrid Yarn Woven Fabrics and Their Composites

Science.gov (United States)

Jagatheesan, Krishnasamy; Ramasamy, Alagirusamy; Das, Apurba; Basu, Ananjan

2017-08-01

This study investigates the shielding characteristics of carbon/stainless steel/polypropylene (C/SS/PP) hybrid woven fabrics and their composites in low frequency (50 MHz-1.5 GHz) and C band (4-6 GHz) regions. The hybrid yarns prepared from carbon and SS filaments using a direct twisting machine have been made into woven fabric samples using a sample loom. The composite has been made by sandwiching a hybrid yarn fabric between the polypropylene films in a compression molding machine at 180°C for 5 min. The shielding behavior of the fabric and the composites has been tested using a coaxial transmission holder for the low frequency range and a wave guide method for the C band frequency range. It has been observed that a 1 end float composite showed a higher SE of 81.4 dB than the 4 end float (76.2 dB) and the 8 end float composites (64 dB) at the low frequency region. However, at the C band frequency, the effect of fabric structures on shielding effectiveness (SE) of fabric composite depends on thread density. For example, at low thread density, (i.e.) 3.93 ppcm, the 8 end float fabric composite showed the highest SE of 22.7 dB than did the 4 end (20.4 dB) and the 1 end float (16.5 dB) fabric composite. However, at high thread density (6.3 ppcm), the case was the reverse. The 1 end float fabric composite showed the highest SE of 29.7 dB rather than 4 end and 8 end float fabric composites (25.9 dB). In addition, all the composites showed less SE than their fabric forms. The increase in thread density also increased the shielding behavior of composites in both frequency ranges. A nonlinear regression model was developed using the Box-Behnken design for predicting the shielding behavior of fabric composites in C band region. In addition to shielding behavior, mechanical strength of C/SS/PP hybrid yarn, the fabric and composite has been tested using a Zwick Roell tensile tester. It has been observed that the work of rupture of C/SS/PP hybrid yarn is higher (6830.3 g

Modelling and Predicting the Breaking Strength and Mass Irregularity of Cotton Rotor-Spun Yarns Containing Cotton Fiber Recovered from Ginning Process by Using Artificial Neural Network Algorithm

Directory of Open Access Journals (Sweden)

Mohsen Shanbeh

2011-01-01

Full Text Available One of the main methods to reduce the production costs is waste recycling which is the most important challenge for the future. Cotton wastes collected from ginning process have desirable properties which could be used during spinning process. The purpose of this study was to develop predictive models of breaking strength and mass irregularity (CV% of cotton waste rotor-spun yarns containing cotton waste collected from ginning process by using the artificial neural network trained with backpropagation algorithm. Artificial neural network models have been developed based on rotor diameter, rotor speed, navel type, opener roller speed, ginning waste proportion and yarn linear density as input parameters. The parameters of artificial neural network model, namely, learning, and momentum rate, number of hidden layers and number of hidden processing elements (neurons were optimized to get the best predictive models. The findings showed that the breaking strength and mass irregularity of rotor spun yarns could be predicted satisfactorily by artificial neural network. The maximum error in predicting the breaking strength and mass irregularity of testing data was 8.34% and 6.65%, respectively.

Parachuting and pregnancy: what do we know about pregnant skydivers and the risks they are taking?

Science.gov (United States)

Ebner, Florian; Wöckel, Achim; Janni, Wolfgang; Paterson, Helen

2014-11-01

There is little medical knowledge about the risks of skydiving during pregnancy. Some national parachuting associations ask for a doctor's permission; others recommend not jumping at all during pregnancy. This article provides survey data and a literature review of pregnancy and parachuting/skydiving related issues to help the pregnant skydiver and her obstetrician make an informed decision. Survey data presented include pregnancy, delivery, and parachuting information from skydivers who jumped during pregnancy. International retrospective anonymous online questionnaire considering the Checklist for Reporting Results of Internet E-Surveys (CHERRIE). The PubMed database was searched with using the terms "skydive," "pregnancy," and "parachute" (query April 2013). Web page questionnaire on skydivers' epidemiology, experience, and pregnancy-related information. Fifty-seven parous female skydivers. Information on athletes' experience, weather conditions, obstetric history (gravida, gestational week), delivery mode was obtained. Epidemiology of pregnant skydivers and literature review to provide information on skydiving risks. Women do actively decide to skydive while pregnant. The majority of our participants were between 25-year-old and 35-year-old primips with 100 to 1000 jumps experience, answering the questionnaire from a European IP address. Precautions are taken in terms of weather conditions, gear, or sports partner. The literature review found no relevant literature regarding the question. Literature is searched for risk factors that come close to the ones in skydiving (ie, oxygen saturation, shock forces, and others). Further studies are needed to show the long-term effect of stress or low O2 saturation on antenatal programming, or short-term hypoxia and pregnancy outcome in pregnant skydiving women and their offspring. Pregnancy itself is a risk factor for injuries. Injuries in pregnancy are clearly associated with an unfavorable pregnancy outcome. The

Efeito da tenacidade da fibra sobre propriedades tecnológicas do fio de algodão Effect of the cotton fiber strength on yarn properties

Directory of Open Access Journals (Sweden)

Nelson Paulieri Sabino

1995-01-01

Full Text Available Consideraram-se três variedades de algodão com valores de tenacidade da fibra variando de 20,5 a 22,2 g/Tex: IAC 16, IAC 13-1 e IAC 17, classificadas, respectivamente, como de alta, média e baixa tenacidade. Tais variedades apresentaram características tecnológicas semelhantes quanto a comprimento, uniformidade de comprimento, índice de finura Micronaire e maturidade. As amostras foram processadas em estabelecimentos industriais, da maneira convencional, produzindo, cada uma, fios de títulos Ne20, Ne30 e Ne40. Para cada título, empregaram-se sete coeficientes de torção, representados pelas constantes 3,4, 3,6, 3,8, 4,0, 4,2, 4,5 e 4,7. Efetuaram-se as análises da variância dos resultados, de acordo com o delineamento fatorial 3 x 3 x 7, representado pelas três variedades, pelos três títulos e pelos sete níveis de coeficientes de torção. Mediante os resultados, conclui-se que fibras de algodão com alta tenacidade produzem fios mais resistentes e elásticos do que aquelas de baixa tenacidade, para qualquer título ou torção. A quantidade de torções requeridas para a obtenção de máxima resistência dos fios de algodão é pouco afetada pela tenacidade da fibra. Os fios de títulos mais altos têm os menores valores de tenacidade e elongação. A variedade IAC 16 apresentou fios com os maiores valores de tenacidade, seguida da 'IAC 13-1' e da 'IAC 17', e fios mais elásticos, acompanhada da 'IAC 17' e da 'IAC 13-1'.Three cottons with fiber strength of 20.5, 20.9 and 22.2 g/Tex and having other important fiber properties approximately equal were selected. The cottons were processed on conventional processing equipment into 20/1, 30/1 and 40/1 yarn counts, using a range of twist multipliers of 3.4, 3.6, 3.8, 4.0, 4.2, 4.5 and 4.7. Yarn strength and elongation determinations were made on a pendulum-type tester of 150-300 lbs capacity. It was found that: 1 - High strength cotton produced stronger yarns than low strength for any

X-Ray Micro-Tomography Applied to Nasa's Materials Research: Heat Shields, Parachutes and Asteroids

Science.gov (United States)

Panerai, Francesco; Borner, Arnaud; Ferguson, Joseph C.; Mansour, Nagi N.; Stern, Eric C.; Barnard, Harold S.; Macdowell, Alastair A.; Parkinson, Dilworth Y.

2017-01-01

X-ray micro-tomography is used to support the research on materials carried out at NASA Ames Research Center. The technique is applied to a variety of applications, including the ability to characterize heat shield materials for planetary entry, to study the Earth- impacting asteroids, and to improve broadcloths of spacecraft parachutes. From micro-tomography images, relevant morphological and transport properties are determined and validated against experimental data.

Tensile strength of woven yarn kenaf fiber reinforced polyester composites

Directory of Open Access Journals (Sweden)

A.E. Ismail

2015-12-01

Full Text Available This paper presents the tensile strength of woven kenaf fiber reinforced polyester composites. The as-received yarn kenaf fiber is weaved and then aligned into specific fiber orientations before it is hardened with polyester resin. The composite plates are shaped according to the standard geometry and uni-axially loaded in order to investigate the tensile responses. Two important parameters are studied such as fiber orientations and number of layers. According to the results, it is shown that fiber orientations greatly affected the ultimate tensile strength but it is not for modulus of elasticity for both types of layers. It is estimated that the reductions of both ultimate tensile strength and Young’s modulus are in the range of 27.7-30.9% and 2.4-3.7% respectively, if the inclined fibers are used with respect to the principal axis.

To improve impact damage response of single and multi-delaminated FRP composites using natural Flax yarn

International Nuclear Information System (INIS)

Ghasemnejad, H.; Soroush, V.R.; Mason, P.J.; Weager, B.

2012-01-01

Highlights: ► To study the impact resistance of delaminated composite structures. ► To improve the impact resistance of delaminated composite structures using natural Flax yarn. ► To investigate the effect of z-pinning on the damage process of composite materials. ► To develop FE techniques to model the impact process of composite structures using LSDYNA. -- Abstract: The ply delamination which is known as a principle mode of failure of layered composites due to separation along the interfaces of the layers is one of the main concerns in designing of composite material structures. In this regard, the effect of hybrid laminate lay-up in multi-delaminated composite beam was investigated. The Charpy impact test was chosen to study the energy absorbing capability of delaminated composite beam. Hybrid composite beams were fabricated from combination of glass/epoxy and carbon/epoxy composites. To improve the impact behaviour of multi-delaminated composite beams the laminated hybrid composite beams were pinned using Flax yarns before curing process. It was shown that the multi-delaminated composite beams which are pinned in z-direction are able to arrest the crack propagation and consequently absorb more energy in comparison with simple ones in hybrid composite beams. The Charpy impact test of delaminated composite beams was also simulated by finite element software LS-DYNA and the results were verified with the relevant experimental results.

Estudo comparativo da resistência do fio de algodão obtido em fiação piloto e em fiação industrial Correlation between laboratory and industrial cotton yarn strength

Directory of Open Access Journals (Sweden)

José Fernando Lazzarini

1972-01-01

Full Text Available O estudo de 81 pares de valores de resistência do fio de algodão 22/1 produzido em fiação piloto (X e em fiação industrial (Y mostrou que entre os dois processos existe uma correlação r= 0,563**. A equação de regressão é da forma Y= 611,631 + 0,486 X. Ficou demonstrado que equações calculadas para nove linhagens em cada localidade fornecem estimativas mais precisas da resistência do fio do que a equação geral. O coeficiente de correlação mais alto (r=0,924** foi encontrado para a localidade de Campinas.A yarn strength correlation analysis for the 22/1 yarn spun through a Miniature Spinning Plant (X and the yarn of same count spun through an industrial equipment (Y was carried out for 81 pairs of observations. The correlation coeficient between the two processes showed to be r = 0.563 **. The regression equation is of the form: Y = 611.631 + 0.486X. It was showed that the equations to predicted yarn strength, calculated for 9 pairs of values in each location, give better estimations than the general equation calculated for 81 pairs in 9 locations. The highest correlation coefficient (r = 0.944 ** was found for the locality of Campinas.

An eco-friendly dyeing of woolen yarn by Terminalia chebula extract with evaluations of kinetic and adsorption characteristics.

Science.gov (United States)

Shabbir, Mohd; Rather, Luqman Jameel; Shahid-Ul-Islam; Bukhari, Mohd Nadeem; Shahid, Mohd; Ali Khan, Mohd; Mohammad, Faqeer

2016-05-01

In the present study Terminalia chebula was used as an eco-friendly natural colorant for sustainable textile coloration of woolen yarn with primary emphasis on thermodynamic and kinetic adsorption aspects of dyeing processes. Polyphenols and ellagitannins are the main coloring components of the dye extract. Assessment of the effect of pH on dye adsorption showed an increase in adsorption capacity with decreasing pH. Effect of temperature on dye adsorption showed 80 °C as optimum temperature for wool dyeing with T. chebula dye extract. Two kinetic equations, namely pseudo first-order and pseudo second-order equations, were employed to investigate the adsorption rates. Pseudo second-order model provided the best fit (R (2) = 0.9908) to the experimental data. The equilibrium adsorption data were fitted by Freundlich and Langmuir isotherm models. The adsorption behavior accorded well (R (2) = 0.9937) with Langmuir isotherm model. Variety of eco-friendly and sustainable shades were developed in combination with small amount of metallic mordants and assessed in terms of colorimetric (CIEL(∗) a (∗) b (∗) and K/S) properties measured using spectrophotometer under D65 illuminant (10° standard observer). The fastness properties of dyed woolen yarn against light, washing, dry and wet rubbing were also evaluated.

An eco-friendly dyeing of woolen yarn by Terminalia chebula extract with evaluations of kinetic and adsorption characteristics

Science.gov (United States)

Shabbir, Mohd; Rather, Luqman Jameel; Shahid-ul-Islam; Bukhari, Mohd Nadeem; Shahid, Mohd; Ali Khan, Mohd; Mohammad, Faqeer

2016-01-01

In the present study Terminalia chebula was used as an eco-friendly natural colorant for sustainable textile coloration of woolen yarn with primary emphasis on thermodynamic and kinetic adsorption aspects of dyeing processes. Polyphenols and ellagitannins are the main coloring components of the dye extract. Assessment of the effect of pH on dye adsorption showed an increase in adsorption capacity with decreasing pH. Effect of temperature on dye adsorption showed 80 °C as optimum temperature for wool dyeing with T. chebula dye extract. Two kinetic equations, namely pseudo first-order and pseudo second-order equations, were employed to investigate the adsorption rates. Pseudo second-order model provided the best fit (R2 = 0.9908) to the experimental data. The equilibrium adsorption data were fitted by Freundlich and Langmuir isotherm models. The adsorption behavior accorded well (R2 = 0.9937) with Langmuir isotherm model. Variety of eco-friendly and sustainable shades were developed in combination with small amount of metallic mordants and assessed in terms of colorimetric (CIEL∗a∗b∗ and K/S) properties measured using spectrophotometer under D65 illuminant (10° standard observer). The fastness properties of dyed woolen yarn against light, washing, dry and wet rubbing were also evaluated. PMID:27222752

Testing the electrostatic characteristics of polypropylene fabric with metallic yarns, intended for use in coal mines threatened by the explosion hazard. Part 2: Tests in coal mine

International Nuclear Information System (INIS)

Talarek, M; Orzech, L

2011-01-01

The aim of this paper was to assess the electrostatic safety of polypropylene fabric with metallic yarns intended for use in coal mines. Such fabrics have not been used in the Polish mining industry yet. The tests conducted have been divided into two subgroups: laboratory tests and tests in a coal mine. This paper presents the results of tests in a coal mine, where we have focused on the resistance-to-ground in some specific situations. Bags made of fabric at the roadway face were tested, as well as the roll of fabric during transport and carried by a miner. The results obtained allow the reliable assessment of the risk of using fabrics with metallic yarns in the explosive atmosphere which often occurs in coal mines.

A Highly Stretchable and Washable All-Yarn-Based Self-Charging Knitting Power Textile Composed of Fiber Triboelectric Nanogenerators and Supercapacitors.

Science.gov (United States)

Dong, Kai; Wang, Yi-Cheng; Deng, Jianan; Dai, Yejing; Zhang, Steven L; Zou, Haiyang; Gu, Bohong; Sun, Baozhong; Wang, Zhong Lin

2017-09-26

Rapid advancements in stretchable and multifunctional wearable electronics impose a challenge on corresponding power devices that they should have comparable portability and stretchability. Here, we report a highly stretchable and washable all-yarn-based self-charging knitting power textile that enables both biomechanical energy harvesting and simultaneously energy storing by hybridizing triboelectrical nanogenerator (TENG) and supercapacitor (SC) into one fabric. With the weft-knitting technique, the power textile is qualified with high elasticity, flexibility, and stretchability, which can adapt to complex mechanical deformations. The knitting TENG fabric is able to generate electric energy with a maximum instantaneous peak power density of ∼85 mW·m -2 and light up at least 124 light-emitting diodes. The all-solid-state symmetrical yarn SC exhibits lightweight, good capacitance, high flexibility, and excellent mechanical and long-term stability, which is suitable for wearable energy storage devices. The assembled knitting power textile is capable of sustainably driving wearable electronics (for example, a calculator or temperature-humidity meter) with energy converted from human motions. Our work provides more opportunities for stretchable multifunctional power sources and potential applications in wearable electronics.

Having a yarn about smoking: using action research to develop a 'no smoking' policy within an Aboriginal Health Organisation.

Science.gov (United States)

Fletcher, Gillian; Fredericks, Bronwyn; Adams, Karen; Finlay, Summer; Andy, Simone; Briggs, Lyn; Hall, Robert

2011-11-01

This article reports on a culturally appropriate process of development of a smoke-free workplace policy within the peak Aboriginal Controlled Community Health Organisation in Victoria, Australia. Smoking is acknowledged as being responsible for at least 20% of all deaths in Aboriginal communities in Australia, and many Aboriginal health workers smoke. The smoke-free workplace policy was developed using the iterative, discursive and experience-based methodology of Participatory Action Research, combined with the culturally embedded concept of 'having a yarn'. Staff members initially identified smoking as a topic to be avoided within workplace discussions. This was due, in part, to grief (everyone had suffered a smoking-related bereavement). Further, there was anxiety that discussing smoking would result in culturally difficult conflict. The use of yarning opened up a safe space for discussion and debate, enabling development of a policy that was accepted across the organisation. Within Aboriginal organisations, it is not sufficient to focus on the outcomes of policy development. Rather, due attention must be paid to the process employed in development of policy, particularly when that policy is directly related to an emotionally and communally weighted topic such as smoking. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Core-Shell-Yarn-Based Triboelectric Nanogenerator Textiles as Power Cloths.

Science.gov (United States)

Yu, Aifang; Pu, Xiong; Wen, Rongmei; Liu, Mengmeng; Zhou, Tao; Zhang, Ke; Zhang, Yang; Zhai, Junyi; Hu, Weiguo; Wang, Zhong Lin

2017-12-26

Although textile-based triboelectric nanogenerators (TENGs) are highly promising because they scavenge energy from their working environment to sustainably power wearable/mobile electronics, the challenge of simultaneously possessing the qualities of cloth remains. In this work, we propose a strategy for TENG textiles as power cloths in which core-shell yarns with core conductive fibers as the electrode and artificial polymer fibers or natural fibrous materials tightly twined around core conductive fibers are applied as the building blocks. The resulting TENG textiles are comfortable, flexible, and fashionable, and their production processes are compatible with industrial, large-scale textile manufacturing. More importantly, the comfortable TENG textiles demonstrate excellent washability and tailorability and can be fully applied in further garment processing. TENG textiles worn under the arm or foot have also been demonstrated to scavenge various types of energy from human motion, such as patting, walking, and running. All of these merits of proposed TENG textiles for clothing uses suggest their great potentials for viable applications in wearable electronics or smart textiles in the near future.

A influência de palmares e parachute na coordenação dos nados

OpenAIRE

Thiago Telles

2012-01-01

Resumo: A natação é uma modalidade esportiva que, ao longo dos anos, sofreu modificações, atingindo um alto nível de exigência, o que é refletido nas sessões de treinamentos e nas pesquisas sobre a modalidade. Sendo assim, para otimizar o deslocamento nos nadadores pode-se otimizar a força propulsora. Para isso, pode-se utilizar palmares e parachute. Os palmares tem como função promover o aumento artificial da área da mão, desta maneira, aumenta-se a área frontal da mão do sujeito em contato ...

Freestyle swimming technique variations using a parachute Variaciones en la técnica de crol durante el nado resistido con paracaídas

Directory of Open Access Journals (Sweden)

J.M. García

2010-09-01

Full Text Available

The appearance of new assistance materials like the parachute make it necessary for coaches to know about the impact that such devices have in swimming. To study this theme 16 national and international swimmers between 19 and 24 years old have been selected. The swimmers participated in four tests that consisted in freestyle (crawl stroke swimming for 10 and 45 seconds at maximum intensity, both with and without the parachute. These tests analysed stroke frequency and stroke length. A within-subjects design has been applied and a study of the facts has been made with an AVAR with repeat measures. The results indicate that the stroke frequency decreases (p<0.05 in the parachute swim during the 10 and 45 second tests, compared with the normal swim. It was also observed that the stroke frequency is higher (p<0.01 in the 10 second test than in the 45 second test. The stroke length is higher (p<0.01 in the normal swim test than in the parachute test. With respect to the swim periods of time, the stroke length is higher (p<0.01 in the 45 second test than in the 10 second test. The parachute swim produces important changes in stroke frequency and stroke length in both the 10 and 45 second tests in subjects swimming the freestyle at maximum intensity.
KEY WORDS: swimming, swim resistance, parachute, crawl, freestyle,. stroke frequency, stroke length.

La aparición de nuevos materiales auxiliares, como el paracaídas, hace necesario que los entrenadores conozcan las modificaciones que estos producen durante el nado. Para conseguir este objetivo se seleccionaron a 16 nadadores de nivel nacional e internacional comprendidos entre los 19 y 24 años. Éstos realizaron cuatro pruebas que consistieron en nadar a crol durante 10 y 45 segundos a máxima intensidad, utilizando el nado normal (NN y el nado resistido con paracaídas (NRCP. En estas pruebas se analizaron las variables

Property of WPU Size in Polyester/Cotton Yarn Sizing%WPU浆料用于涤棉纱上浆的性能

Institute of Scientific and Technical Information of China (English)

王宝根

2012-01-01

The heat stability of size viscosity of water soluble polyurethane（WPU）, humidity of sizing membrane and property of single sizing yarn were tested. WPU size was comparative analyzed with some market size and the results showed that the sizing performance of WPU could match PVA complex size under the condition of 95 ℃, viscosity of 12 MPa ; s, relative humidity of 75%, moisture absorption rate of 11.6% in T65/C35 13 tex single yarn.%测试了wPU水性聚氨酯浆料的浆液粘度热稳定性、浆膜吸湿性和上浆单纱的基本性能，并与市场上现有的一些浆料进行了对比分析。结果表明，WPU浆在95℃下粘度保持在12MPa·s左右；在75％相对湿度下，浆膜吸湿率为11．6％；在T65／C3513tex单纱浆纱性能上，与市场上含PVA的复配浆料的上浆效果相差不大。

Efeitos do treinamento de força específico no desempenho de nadadores velocistas treinados com parachute

Directory of Open Access Journals (Sweden)

Danilo Sales Bocalini

2010-09-01

Full Text Available OBJETIVO: verificar os efeitos do treinamento de força específico no desempenho de nadadores velocistas. METODOLOGIA: dois grupos de nadadores randomizados em treinados sem (TSP, n: 8 e com parachute (TCP, n: 12 foram submetidos a treinamento de 12 semanas (6 x semana; 1 sessão de 2 h/dia, sendo avaliados a força muscular (FMMI; a força específica (FE e o tempo de sustentação de força (TSF; o número de braçadas em 50m (NB 50m; o tempo e a velocidade de nado em 15 (V 15m e 50m (V 50m, antes e após o protocolo. RESULTADOS: após o programa de treinamento, não ocorreram modificações na FMMI e V 15m para ambos os grupos. Nas demais variáveis houve melhora significante (p 18%; FE (> 30%; TSF (> 35%; NB 50m ( 16%. O grupo TSP apresentou melhora no TSF (> 9%. CONCLUSÃO: o emprego do parachute foi eficiente em melhorar os parâmetros de força e no desempenho no teste de 50m

Highly water-absorbing silk yarn with interpenetrating network via in situ polymerization.

Science.gov (United States)

Lee, Ka I; Wang, Xiaowen; Guo, Xia; Yung, Ka-Fu; Fei, Bin

2017-02-01

Silk was modified via in situ polymerization of two monomers acrylamide and sodium acrylate by swelling in an effective LiBr dissolution system. Swelling of natural silks in LiBr solutions of low concentration was clearly observed under optical microscope, and their conformational changes were revealed by X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy. Dissolution tests and FTIR spectra of these modified silks suggested the presence of interpenetrating network of polyacrylamide and poly(sodium acrylate) in the silk yarns. These modified silks exhibited superior water absorption to that of raw silk and greatly improved mechanical properties in both dry and wet states. These novel modified silks also showed low cytotoxicity towards skin keratinocytes, having potential applications in biomedical textiles. This modification method by in situ polymerization after swelling in LiBr provides a new route to highly enhance the properties and performance of silk for various applications. Copyright © 2016 Elsevier B.V. All rights reserved.

O2 Plasma Etching and Antistatic Gun Surface Modifications for CNT Yarn Microelectrode Improve Sensitivity and Antifouling Properties.

Science.gov (United States)

Yang, Cheng; Wang, Ying; Jacobs, Christopher B; Ivanov, Ilia N; Venton, B Jill

2017-05-16

Carbon nanotube (CNT) based microelectrodes exhibit rapid and selective detection of neurotransmitters. While different fabrication strategies and geometries of CNT microelectrodes have been characterized, relatively little research has investigated ways to selectively enhance their electrochemical properties. In this work, we introduce two simple, reproducible, low-cost, and efficient surface modification methods for carbon nanotube yarn microelectrodes (CNTYMEs): O 2 plasma etching and antistatic gun treatment. O 2 plasma etching was performed by a microwave plasma system with oxygen gas flow and the optimized time for treatment was 1 min. The antistatic gun treatment flows ions by the electrode surface; two triggers of the antistatic gun was the optimized number on the CNTYME surface. Current for dopamine at CNTYMEs increased 3-fold after O 2 plasma etching and 4-fold after antistatic gun treatment. When the two treatments were combined, the current increased 12-fold, showing the two effects are due to independent mechanisms that tune the surface properties. O 2 plasma etching increased the sensitivity due to increased surface oxygen content but did not affect surface roughness while the antistatic gun treatment increased surface roughness but not oxygen content. The effect of tissue fouling on CNT yarns was studied for the first time, and the relatively hydrophilic surface after O 2 plasma etching provided better resistance to fouling than unmodified or antistatic gun treated CNTYMEs. Overall, O 2 plasma etching and antistatic gun treatment improve the sensitivity of CNTYMEs by different mechanisms, providing the possibility to tune the CNTYME surface and enhance sensitivity.

Application of a hybrid Electrocoagulation-Fenton process in yarn dye wastewater: Kinetic study

Science.gov (United States)

Riadi, L.; Sapei, L.; Lidiawati, T.; Agustin, Y. E.

2016-11-01

Reactive dyes contain a significant portion of colorants used in yarn dying process and also in textile industry. Since the COD content is usually high in such wastewater,we conducted a hybrid electrocoagulation-fenton method to treat the wastewater. This work describes the application of the hybrid system to the removal of chemical oxygen demand and color from the wastewater in a batch reactor. Having worked with initial pH of 3,0; temperature at 30°C, molar ratio of Fe2+/H2O2 =1/10 and the mol ratio H2O2/COD = 4, we got 88.3% COD conversion and 88.5% color removal. The COD degradation process can be explained in two phases, the first phase is instantaneous reaction and the second phase is first order reaction. The kinetic constant was 0.0053 minute-1 and the rate of COD degradation was 0.0053[COD] mg/L minute.

Additive Manufacturing of Multifunctional Components Using High Density Carbon Nanotube Yarn Filaments

Science.gov (United States)

Gardner, John M.; Sauti, Godfrey; Kim, Jae-Woo; Cano, Roberto J.; Wincheski, Russell A.; Stelter, Christopher J.; Grimsley, Brian W.; Working, Dennis C.; Siochi, Emilie J.

2016-01-01

Additive manufacturing allows for design freedom and part complexity not currently attainable using traditional manufacturing technologies. Fused Filament Fabrication (FFF), for example, can yield novel component geometries and functionalities because the method provides a high level of control over material placement and processing conditions. This is achievable by extrusion of a preprocessed filament feedstock material along a predetermined path. However if fabrication of a multifunctional part relies only on conventional filament materials, it will require a different material for each unique functionality printed into the part. Carbon nanotubes (CNTs) are an attractive material for many applications due to their high specific strength as well as good electrical and thermal conductivity. The presence of this set of properties in a single material presents an opportunity to use one material to achieve multifunctionality in an additively manufactured part. This paper describes a recently developed method for processing continuous CNT yarn filaments into three-dimensional articles, and summarizes the mechanical, electrical, and sensing performance of the components fabricated in this way.

Wettability and sizing property improvement of raw cotton yarns treated with He/O{sub 2} atmospheric pressure plasma jet

Energy Technology Data Exchange (ETDEWEB)

Sun Shiyuan [Key Laboratory of Textile Science and Technology, Ministry of Education, China, College of Textiles, Donghua University, Shanghai 201620 (China); College of Textiles and Clothing Engineering, Dezhou University, Shandong 253023 (China); Sun Jie; Yao Lan [Key Laboratory of Textile Science and Technology, Ministry of Education, China, College of Textiles, Donghua University, Shanghai 201620 (China); Qiu Yiping, E-mail: ypqiu@dhu.edu.cn [Key Laboratory of Textile Science and Technology, Ministry of Education, China, College of Textiles, Donghua University, Shanghai 201620 (China)

2011-01-01

Raw cotton fiber is water repellent due to the existence of the water repellent cuticle layer. This study is designed to systematically investigate how He/O{sub 2} atmospheric pressure plasma jet (APPJ) treatments influence the wettability and the sizing property of cotton yarns. Water absorption time and adhesion of the sizing agent to the cotton roving are used to evaluate the improvement of wettability and sizing property of the yarn respectively. The water absorption time decreases with the increase of the treatment time and the oxygen flow rate, and the decrease of the jet to substrate distance (JTSD). An optimal water absorption time of 0.8 s is obtained with a treatment time of 20 s, JTSD of 1 mm and O{sub 2} flow rate of 0.2 L/min. Scanning electron microscopy (SEM) shows that the etching effect increases with the decrease of the JTSD and X-ray photoelectron spectroscopy (XPS) presents increased oxygen contents after the plasma treatments. An increase of O-C=O bonds while a decrease of C-OH/C-O-C bonds are observed when the JTSD is set at 2 mm. However, a remarkable increase of both C-OH/C-O-C and O-C=O bonds are achieved when the JTSD is 1 mm. The roving impregnation test results show a nearly doubled adhesion of sizing and a slightly improved breaking elongation, indicating that the plasma treatment does effectively enhance the bonding strength between the fiber and the sizing.

Poly(D,L-Lactide-Co-Glycolide) Tubes With Multifilament Chitosan Yarn or Chitosan Sponge Core in Nerve Regeneration.

Science.gov (United States)

Wlaszczuk, Adam; Marcol, Wiesław; Kucharska, Magdalena; Wawro, Dariusz; Palen, Piotr; Lewin-Kowalik, Joanna

2016-11-01

The influence of different kinds of nerve guidance conduits on regeneration of totally transected rat sciatic nerves through a 7-mm gap was examined. Five different types of conduits made of chitosan and poly(D,L-lactide-co-glycolide) (PLGA) were constructed and tested in vivo. We divided 50 animals into equal groups of 10, with a different type of conduit implanted in each group: chitosan sponge core with an average molecular mass of polymer (Mv) of 287 kDa with 7 channels in a PLGA sleeve, chitosan sponge core with an Mv of 423 kDa with 7 channels in a PLGA sleeve, chitosan sponge core (Mv, 423 kDa) with 13 channels in a PLGA sleeve, chitosan multifilament yarn in a PLGA sleeve, and a PLGA sleeve only. Seven weeks after the operation, we examined the distance covered by regenerating nerve fibers, growing of nerves into the conduit's core, and intensity and type of inflammatory reaction in the conduit, as well as autotomy behavior (reflecting neuropathic pain intensity) in the animals. Two types of conduits were allowing nerve outgrowth through the gap with minor autotomy and minor inflammatory reactions. These were the conduits with chitosan multifilament yarn in a PLGA sleeve and the conduits with 13-channel microcrystalline chitosan sponge in a PLGA sleeve. The type of chitosan used to build the nerve guidance conduit influences the intensity and character of inflammatory reaction present during nerve regeneration, which in turn affects the distance crossed by regenerating nerve fibers, growing of the nerve fibers into the conduit's core, and the intensity of autotomy in the animals. Copyright © 2016 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Thermo-Mechanical Behavior of Textile Heating Fabric Based on Silver Coated Polymeric Yarn

Directory of Open Access Journals (Sweden)

Anura Fernando

2013-03-01

Full Text Available This paper presents a study conducted on the thermo-mechanical properties of knitted structures, the methods of manufacture, effect of contact pressure at the structural binding points, on the degree of heating. The test results also present the level of heating produced as a function of the separation between the supply terminals. The study further investigates the rate of heating and cooling of the knitted structures. The work also presents the decay of heating properties of the yarn due to overheating. Thermal images were taken to study the heat distribution over the surface of the knitted fabric. A tensile tester having constant rate of extension was used to stretch the fabric. The behavior of temperature profile of stretched fabric was observed. A comparison of heat generation by plain, rib and interlock structures was studied. It was observed from the series of experiments that there is a minimum threshold force of contact at binding points of a knitted structure is required to pass the electricity. Once this force is achieved, stretching the fabric does not affect the amount of heat produced.

Test Research of Reducing Combed Yarn Neps%降低精梳纱棉结的试验研究

Institute of Scientific and Technical Information of China (English)

赵建伟

2011-01-01

Technology measures of reducing combed yarn neps were discussed.Causes of combed yarn neps formation and changing rules in spinning were analyzed.Cotton assorting and processing configurations in each process were modified and optimized.Basic management works were enhanced such as raw cotton selection, equipment clean, operation clean and temperature & humidity control.Finally neps of CJ 18.2 tex cheese and CJ 22.4 tex cheese could be kept below 31 per kilometer and 25 per kilometer.It is pointed out that processing in cotton assorting,carding and combing process should be set rationally,reducing neps is a system project,the key points should be focused, whole process control should be implemented and basic management should be strengthened, finally the better effect could be got.%探讨降低精梳纱棉结的技术措施.分析了精梳纱棉结的形成原因及纺纱过程中的变化规律,通过对配棉及各工序的工艺进行改进和优化配置,加强原棉、设备揩车和运转清洁工作及温湿度等各项基础管理工作,结果使CJ 18.2 tex、CJ 22.4 tex筒纱棉结长期保持在31个/km和25个/km以下.指出:减少精梳纱棉结是一项系统工程,仅仅依靠配棉、梳棉、精梳工序的作用是不够的,应突出重点实行纺纱全过程控制并切实加强基础性管理工作,才能收到较好效果.

Processing Key Point of Developing Flax Viscose Blended Yarn on Cotton Spinning Equipment%棉纺设备开发亚麻粘胶混纺纱的工艺要点

Institute of Scientific and Technical Information of China (English)

赵建伟

2011-01-01

To develop and produce flax/viscose 80/20 blended yarn on cotton spinning equipment, through selec-ting raw material rationally, pretreating flax fiber, improving and optimizing spinning processing, controlling each process relative humidity, strengthening equipment management and running cleaning, problems in production were resolved, fi-nally blended yarn can be spun successfully, production efficiency is above 90% , product quality can be reached better level and user quality requirements can be satisfied.%为了使用棉纺设备开发和生产亚麻/粘胶80/20混纺纱,通过合理选用原料,对亚麻进行预处理,改进和优化纺纱工艺,控制好各工序的相对湿度,加强设备管理和运转清洁工作,解决了生产中出现的问题,使各工序的纺纱顺利进行,生产效率达到90%以上,产品质量达到了较好水平,满足了用户质量要求.

Electrokinetic remediation of heavy metals contaminated kaolin by a CNT-covered polyethylene terephthalate yarn cathode

International Nuclear Information System (INIS)

Yuan, Lizhu; Li, Haiyan; Xu, Xingjian; Zhang, Jing; Wang, Nana; Yu, Hongwen

2016-01-01

In the current study, carbon nanotube (CNT) covered polyethylene terephthalate yarns (PET-CNT) electrode has been investigated as a novel cathode material for the electrokinetic (EK) remediation of multi-metals (Cd, Cu, Ni, Pb, Zn) contaminated kaolin. The results of scanning electron microscopy (SEM) and thermogravimetric analysis (TGA) showed that CNT was successfully covered on the surface of PET. The results obtained from EK process showed that PET-CNT as a cathode obviously elevated electric current and electro-osmotic flow (EOF), significantly decreased kaolin pH, and enhanced heavy metals removal efficiencies. The removal efficiencies of Cd, Cu, Ni, Pb, and Zn in PET-CNT treatment were 89.7%, 63.6%, 90.7%, 19.2%, and 88.7%, respectively. In comparison with the Pt/Ti and graphite treatments, the removal efficiencies of Cd, Ni, and Zn were improved at least about 30%, Cu and Pb were improved at least 16.6% and 6.9%, respectively. Our results demonstrated the PET-CNT was a good alternative cathode material for enhancing efficiency of EK remediation.

High Performance Carbon Nanotube Yarn Supercapacitors with a Surface-Oxidized Copper Current Collector.

Science.gov (United States)

Zhang, Daohong; Wu, Yunlong; Li, Ting; Huang, Yin; Zhang, Aiqing; Miao, Menghe

2015-11-25

Threadlike linear supercapacitors have demonstrated high potential for constructing fabrics to power electronic textiles (eTextiles). To improve the cyclic electrochemical performance and to produce power fabrics large enough for practical applications, a current collector has been introduced into the linear supercapcitors to transport charges produced by active materials along the length of the supercapacitor with high efficiency. Here, we first screened six candidate metal filaments (Pt, Au, Ag, AuAg, PtCu, and Cu) as current collectors for carbon nanotube (CNT) yarn-based linear supercapacitors. Although all of the metal filaments significantly improved the electrochemical performance of the linear supercapacitor, two supercapacitors constructed from Cu and PtCu filaments, respectively, demonstrate far better electrochemical performance than the other four supercapacitors. Further investigation shows that the surfaces of the two Cu-containing filaments are oxidized by the surrounding polymer electrolyte in the electrode. While the unoxidized core of the Cu-containing filaments remains highly conductive and functions as a current collector, the resulting CuO on the surface is an electrochemically active material. The linear supercapacitor architecture incorporating dual active materials CNT + Cu extends the potential window from 1.0 to 1.4 V, leading to significant improvement to the energy density and power density.

THE EFFICIENCY OF YARN WOUND FILTERS IN GIARDIA CYSTS REMOVAL USING THE IMPROVED SUCROSE GRADIENT

Directory of Open Access Journals (Sweden)

M.R SHAH MANSOURI

2001-09-01

Full Text Available Introduction. The protozoan parasite Giardia is one of the important biological cotaminants in water. lts presence in water has caused the outbreak of a number of epidemics in various part of the world including the United States. The major impediment in detecting this particular parasite is unavailability of suitable filters capable of removing it from water. Regarding the fact yarn wound filters (cartridge used in removing Giardia under laboratory condition are currently difficult to obtain in Iran, attempts were made to design and manufacture the filters according to standards recommended in the literature. Methods. To determine the efficiency of filters manufactured in this way, a pilot system was established and parameters of concern were investigated. A given number of cysts were introduced in each case to the water in the pilot tank after being counted on the hemocytometer lamella After the entire tank water (at least 4001had been pumped through the filters, the filter were removed from the pilot system to have their yarns separated and washed. The cysts recovered were then counted and compared with the original input cysts to determine the efficiency of the filters. Formation of sediments on filters due to suspended solids in water was a great impediment in counting the cysts hidden in the sediments. To overcome this difficulty, the method of floatation in sucrose was used to remove the hidden cysts from the sediments. Regarding the morphological characteristics of the cysts, the method was also studied in terms of the sucrose film concentration and the effects of centrifugal speed and duration on the removal of cysts from sediments. Results. The results indicated an efficiency of 80.69±5.85, which was ideal for a first experience in Iran. a level of 2.5 molar of Sucrose with a duration of 10 minutes for the centrifugation time at 2,000 rpm were considered to be optimum levels to yield a certainty of 95 percent and an efficiency of

Yarn supplier selection using analytical hierarchy process (AHP) and standardized unitless rating (SUR) method on textile industry

Science.gov (United States)

Erfaisalsyah, M. H.; Mansur, A.; Khasanah, A. U.

2017-11-01

For a company which engaged in the textile field, specify the supplier of raw materials for production is one important part of supply chain management which can affect the company's business processes. This study aims to identify the best suppliers of raw material suppliers of yarn for PC. PKBI based on several criteria. In this study, the integration between the Analytical Hierarchy Process (AHP) and the Standardized Unitless Rating (SUR) are used to assess the performance of the suppliers. By using AHP, it can be known the value of the relative weighting of each criterion. While SUR shows the sequence performance value of the supplier. The result of supplier ranking calculation can be used to know the strengths and weaknesses of each supplier based on its performance criteria. From the final result, it can be known which suppliers should improve their performance in order to create long term cooperation with the company.

Influencing Factors of the Initiation Point in the Parachute-Bomb Dynamic Detonation System

Science.gov (United States)

Qizhong, Li; Ye, Wang; Zhongqi, Wang; Chunhua, Bai

2017-12-01

The parachute system has been widely applied in modern armament design, especially for the fuel-air explosives. Because detonation of fuel-air explosives occurs during flight, it is necessary to investigate the influences of the initiation point to ensure successful dynamic detonation. In fact, the initiating position exist the falling area in the fuels, due to the error of influencing factors. In this paper, the major influencing factors of initiation point were explored with airdrop and the regularity between initiation point area and factors were obtained. Based on the regularity, the volume equation of initiation point area was established to predict the range of initiation point in the fuel. The analysis results showed that the initiation point appeared area, scattered on account of the error of attitude angle, secondary initiation charge velocity, and delay time. The attitude angle was the major influencing factors on a horizontal axis. On the contrary, secondary initiation charge velocity and delay time were the major influencing factors on a horizontal axis. Overall, the geometries of initiation point area were sector coupled with the errors of the attitude angle, secondary initiation charge velocity, and delay time.

The electro-structural behaviour of yarn-like carbon nanotube fibres immersed in organic liquids

International Nuclear Information System (INIS)

Terrones, Jeronimo; Windle, Alan H; Elliott, James A

2014-01-01

Yarn-like carbon nanotube (CNT) fibres are a hierarchically-structured material with a variety of promising applications such as high performance composites, sensors and actuators, smart textiles, and energy storage and transmission. However, in order to fully realize these possibilities, a more detailed understanding of their interactions with the environment is required. In this work, we describe a simplified representation of the hierarchical structure of the fibres from which several mathematical models are constructed to explain electro-structural interactions of fibres with organic liquids. A balance between the elastic and surface energies of the CNT bundle network in different media allows the determination of the maximum lengths that open junctions can sustain before collapsing to minimize the surface energy. This characteristic length correlates well with the increase of fibre resistance upon immersion in organic liquids. We also study the effect of charge accumulation in open interbundle junctions and derive expressions to describe experimental data on the non-ohmic electrical behaviour of fibres immersed in polar liquids. Our analyses suggest that the non-ohmic behaviour is caused by progressively shorter junctions collapsing as the voltage is increased. Since our models are not based on any property unique to carbon nanotubes, they should also be useful to describe other hierarchical structures. (paper)

Parachute Creek Shale Oil Program Environmental Monitoring Program. Quarterly report, fourth quarter, October 1-December 31, 1991

International Nuclear Information System (INIS)

1992-01-01

The Energy Security Act of 1980 established a program to provide financial assistance to private industry in the construction and operation of commercial-scale synthetic fuels plants. The Parachute Creek Shale Oil Program is one of four projects awarded financial assistance. The Program agreed to comply with existing environmental monitoring regulations and to develop an Environmental Monitoring Plan (EMP) incorporating supplemental monitoring in the areas of water, air, solid waste, and worker health and safety during the period 1985-1992. These activities are described in a series of quarterly and annual reports. The document contains environmental compliance data collected in the fourth quarter of 1991, contents of reports on compliance data submitted to regulatory agencies, and supplemental analytical results from retorted shale pile runoff water collected following a storm event during the third quarter of 1991

Unocal Parachute Creek Shale Oil Program Environmental Monitoring Program. Annual report, October 1, 1990-December 31, 1991

International Nuclear Information System (INIS)

1992-01-01

The Energy Security Act of 1980 established a program to provide financial assistance to private industry in the construction and operation of commercial-scale synthetic fuels plants. The Parachute Creek Shale Oil Program is one of four projects awarded financial assistance. The Program agreed to comply with existing environmental monitoring regulations and to develop an Environmental Monitoring Plan (EMP) incorporating supplemental monitoring in the areas of water, air, solid waste, and worker health and safety during the period 1985-1992. These activities are described in a series of quarterly and annual reports. The report contains summaries of compliance and supplemental environmental and industrial hygiene and health surveillance monitoring conducted during the period; compliance permits, permit changes, and Notices of Violations discussions; statistical significance of Employee General Health information, medical histories, physical exams, pulmonary functions, clinical tests and demographics; independent audit reports; and a description of retorted shale disposal activities

Unocal Parachute Creek Shale Oil Program. Environmental Monitoring Plan quarterly report. Fourth quarter, 1989. Rept. for 1 Oct-31 Dec 89

International Nuclear Information System (INIS)

1990-01-01

The Energy Security Act of 1980 established a program to provide financial assistance to private industry in the construction and operation of commerical-scale synthetic fuels plants. The Parachute Creek Shale Oil Program is one of four projects awarded financial assistance. The Program agreed to comply with existing environmental monitoring regulations and to develop an Environmental Monitoring Plan incorporating supplemental monitoring in the areas of water, air, solid waste, and worker health and safety during the period 1985-1992. These activities are described in a series of quarterly and annual reports. The report contains environmental compliance data reports, results of industrial hygiene compliance monitoring, and independent audits. Table 2-1 shows 14 of the 20 supplemental monitoring sites sampled during the quarter

The effect of z-binding yarns on the electrical properties of 3D woven composites

KAUST Repository

Saleh, Mohamed Nasr

2017-09-28

Electrical resistance monitoring (ERM) has been used to study the effect of the z-binding yarns on the initial electrical resistance (ER) and its change of three architectures of 3D woven carbon fibre composites namely (orthogonal “ORT”, layer-to-layer “LTL” and angle interlock “AI”) when tested in tension. Specimens are loaded in on-axis “warp” and off-axis “45°” directions. In-situ ERM is achieved using the four-probe technique. Monotonic and cyclic “load/unload” tests are performed to investigate the effect of piezo-resistivity and residual plasticity on resistance variation. The resistance increase for the off-axis loaded specimens (∼90%) is found to be higher than that of their on-axis counterparts (∼20%). In the case of cyclic testing, the resistance increase upon unloading is irreversible which suggests permanent damage presence not piezo-resistive effect. At the moment, it is difficult to obtain a direct correlation between resistance variation and damage in 3D woven composites due to the complexity of the conduction path along the three orthogonal directions, however this study demonstrates the potential of using ERM for damage detection in 3D woven carbon fibre-based composites and highlights the challenges that need to be overcome to establish ERM as a Structural Health Monitoring (SHM) technique for such material systems.

UNOCAL Parachute Creek Shale Oil Program. Environmental Monitoring Plan - supplemental environmental. Volume 1. Trip 2 report. Rept. for 1988-90

International Nuclear Information System (INIS)

1991-01-01

The Energy Security Act of 1980 established a program to provide financial assistance to private industry in the construction and operation of commercial-scale synthetic fuels plants. The Parachute Creek Shale Oil Program is one of four projects awarded financial assistance. The Program agreed to comply with existing environmental monitoring regulations and to develop an Environmental Monitoring Plan (EMP) incorporating supplemental monitoring in the areas of water, air, solid waste, and worker health and safety during the period 1985-1992. These activities are described in a series of quarterly and annual reports. The report contains results of three years of supplemental environmental sampling (Trial Trip, 1988; Trip 1, 1989; and Trip 2, 1990); Trip 2 sampling and analytical methods; quality assurance and quality control procedures; sampling and analytical methods; and corrected data from 1988 and 1989 gas and particulate concentrations

PVDF multifilament yarns grafted with polystyrene induced by γ-irradiation: Influence of the grafting parameters on the mechanical properties

International Nuclear Information System (INIS)

Marmey, P.; Porte, M.C.; Baquey, Ch.

2003-01-01

The development of alternative prosthetic materials for cardiovascular applications has found growing interest due to the failure to date to be able to implement functional patent small diameter vascular grafts (diameter <5 mm). For instance, the successful implantation of small diameter polyester (PET) and expanded polytetrafluoroethylene (PTFEe) vascular grafts has not been achieved in humans. Our strategy is to work with a new multifilament yarns biomaterial, produced from polyvinylidene fluoride (PVDF), which shows suitable mechanical properties, such as a lower tensile modulus than PET and PTFEe. The required biological properties sought for (i.e. low thrombogenicity) could be achieved by 'heparin-like' surface modification treatments in order to modify the thrombogenicity levels of the polymeric materials [Ann. Biomed. Eng. 7 (1979) 429]. A four step method is necessary to achieve this 'heparin-like' surface transformation [J. Biomed. Mater. Res. 52 (2000) 119]. The first step consists in grafting polystyrene onto the PVDF surface by γ irradiation. The purpose of this study was to evaluate the influence of grafting parameters on the mechanical properties: (i) γ-ray irradiation time and (ii) grafting time of styrene monomers, which polymerize and form polystyrene bound to the PVDF surface

The Assessment of Natural Pigmentation in Archaeological Wool

DEFF Research Database (Denmark)

Scharff, Annemette Bruselius

2018-01-01

Naturally coloured wool contains pigment grains that mainly occur as ellipsoidal organelles (eumelanin) or spher¬ical grains (pheomelanin). Eumelanin is the most commonly occurring pigment, but naturally coloured wool fi¬bres contain both eumelanin and pheomelanin. In black and brown wool....... This can especially be the case if the pigments are degraded. When analysing the textiles from Lønne Hede (a Danish Iron Age inhumation grave), it was difficult to gain exact information about the natural pigmentation in some of the samples. To investigate this further, four samples of red-brown yarns from...... patterned fragments were selected for analyses. Earlier dyestuff analyses of the red-brown yarns gave no results, and it was therefore necessary to test the yarns for natural pigmentation. Three different methods were used for the analy¬ses. Transmitted light microscopy of whole mounts of the fibres...

Electrospinning of single wall carbon nanotube reinforced aligned fibrils and yarns

Science.gov (United States)

Lam, Hoa Le

Commercial carbon fibers produced from a polyacrylonitrile (PAN) precursor have reached their performance limit. The approach in this study involves the use of single carbon nanotubes (SWNT) with an ultra-high elastic modulus of approximately ˜1 TPa and tensile strength of ˜37 GPa at a breaking strain of ˜6% to reinforce PAN. In order to translate these extraordinary properties to a higher order structure, the need for a media to carry and assemble the SWNT into continuous fibers or yarns is necessary. Effective translation of properties can only be achieved through uniform distribution of SWNT and their alignment in the fiber axis. This has been one of the major challenges since SWNTs tend to agglomerate due to high van der Waals attraction between tubes. It is the goal of this study to develop dispersion technique(s) for the SWNT and process them into aligned fibers utilizing the electrospinning process. The electrospun nanofibers were then characterized by various techniques such as ESEM, Raman microspectroscopy, HRTEM, and tensile testing. Composite nanofibers containing various contents of SWNT up to 10 wt. % with diameter ranging from 40--300 nm were successfully electrospun through varying the polymer concentration and spinning parameters. The inclusion of SWNTs and their alignment in the fiber axis were confirmed by Raman microspectroscopy, polarized Raman and HRETEM. The failure mechanism of the nanofibers was investigated by HRTEM through fiber surface fracture. A two stage rupture mechanism was observed where crazing initiates at a surface defect followed by SWNTs pulling out of the PAN matrix. Such mechanisms consume energy therefore strengthening and toughening the fibers. Mechanical drawing of the fiber prior to heat treatment induced molecular orientation resulting in oriented graphite layers in the carbonized fibers. This study has established a processing base and characterization techniques to support the design and development of SWNT

STUDY OF THE INFLUENCE OF SYNTHETIC COMPONENT IN MIXTURES WITH WOOL ON THE PHYSICAL-MECHANICAL PROPRIETIES

Directory of Open Access Journals (Sweden)

OANA Dorina

2016-05-01

Full Text Available The main physical-mechanical properties of the yarns are: linear density (Tex, tensile strength, tenacity, elongation at break, twisting and mechanical work of fracture, there is a strong correlation between them. The tensile properties are the basic characteristics of yarns, influencing how they behave in the technological processes of mechanical processing (preparation for weaving or knitting, proper weaving or knitting determining the technological parameters of equipment adjusting during the technological processes and also their productivity. The tensile properties of yarns constitute qualitative characteristics, because their value depends on the quality of the yarn and also on the finite product obtained from processing yarns. In this paper was done a comparative study of the tensile properties of two batches of mixed woolen yarns (wool with polyester and wool with polyamide, the mixture being in the same proportions, but the yarns have different fineness and have very close twist values, both batches of yarns were designed for knitted products. Batch I consists of 70% wool yarns and 30% polyester, linear density Ttex = 55.56 tex and twist of 350 twists/meter. Batch II consists of 70% wool yarns and 30% polyamide, a linear density of Ttex = 71.34 tex and twist of 330 twists/meter (so a thicker yarn than the one from batch I. Following the analysis between the two batches is clear that the woolen yarns in batch II have much higher tensile properties.

A Comparative Study of Hooks in the Ya Rns Produced by Different Spinning Technologies

Directory of Open Access Journals (Sweden)

Ghosh Anindya

2015-12-01

Full Text Available This article presents a comparative study of hooks’ characteristics of ring, rotor, air-jet and open-end friction spun yarns. Hook types and their extent, spinning in-coefficient and mean fibre extent in the yarns produced on different spinning technologies are investigated. The results show that the hook extents for open-end friction spun yarn are the highest followed by rotor, ring and air-jet spun yarns. Ring and air-jet spun yarns have higher percentage and extent of trailing hook as compared with leading hook, whereas, rotor and friction spun yarns show the reverse trend.

Wrap Spinning: Principles and Development

CSIR Research Space (South Africa)

Brydon, AG

1986-02-01

Full Text Available A wrap yarn is a composite structure comprising a core of twisted or twisted fibres bound by a yarn or continuous filament. The term wrap yarn therefore include yarns produced by the hollow spindle method as well as similar structure such as selfil...

改造喷气织机开发四纱并列起格弹力格子布%RECONSTRUCTION JET LOOMS FOR THE DEVELOPMENT OF FOUR PARALLEL YARN GRID ELASTIC PLAID

Institute of Scientific and Technical Information of China (English)

陈声富

2016-01-01

Developed four-parallel-yarn grid elastic plaid by double beam weaving transformation in JAT-190TNT-T610 model Toyota four-jet looms. Product has clear cell type and fabric fullness. Its style and quality is compliance with the requirements of the market, which has become a highlight in market selling varieties.%通过双经轴织造改造，在JAT-190TNT-T610型日本丰田喷气织机上开发的四纱并列起格的弹力格子布，格型清晰，布面丰满，风格和质量完全符合市场要求。

Compressibility and resiliency properties of wilton type woven carpets produced with different fiber blend ratio

Science.gov (United States)

Osman, B.; Esin, S.; Sıdıka Ziba, O.

2017-10-01

Carpet is a textile structure that composed of three components: warp (stuffer and chain warp), weft and pile yarns. These textile products are used for areas which will stand up to the use of home, hotel, work place etc. Furthermore, the capable of carpets are related to it’s especially pile performance during use in various areas. During usage, carpets made from various type of raw materials of pile yarn also acts differently that these differentiate determines carpet performance, as well.This study was focused on the compression and resilience behaviour of carpet composed of 100% viscose and 100% acrylic pile yarns and blended pile yarns of blend ratios, 80%/20%, 50%/50% and 20%/80% viscose/acrylic. During the yarn production process, all spinning conditions were kept constant in order to eliminate the yarn production parameters. Five different types of wilton face to face carpet samples were produced from these yarns at the same pile height and pile density on Van de Wiele carpet weaving machine at 110 picks/min machine speed and 1/1 V carpet construction. Compressibility properties of carpets were examined whether blend ratio was statistically significant on carpet resilience or not. The behaviour of pile yarns under pressure is important that leads to understand the growth characteristic which is exposed to decrease and increase loadings during usage of carpet made from these yarns. Results indicated that blend ratio of pile yarns have significance effect on compression behaviour of carpet samples.

Migration of additive molecules in a polymer filament obtained by melt spinning: Influence of the fiber processing steps

Science.gov (United States)

Gesta, E.; Skovmand, O.; Espuche, E.; Fulchiron, R.

2015-12-01

The purpose of this study is to understand the influence of the yarn processing on the migration of additives molecules, especially insecticide, within polyethylene (PE) yarns. Yarns were manufactured in the laboratory focusing on three key-steps (spinning, post-stretching and heat-setting). Influence of each step on yarn properties was investigated using tensile tests, differential scanning calorimetry and wide-angle X-ray diffraction. The post-stretching step was proved to be critical in defining yarn mechanical and structural properties. Although a first orientation of polyethylene crystals was induced during spinning, the optimal orientation was only reached by post-stretching. The results also showed that the heat-setting did not significantly change these properties. The presence of additives crystals at the yarn surface was evidenced by scanning-electron microscopy. These studies performed at each yarn production step allowed a detailed analysis of the additives' ability to migrate. It is concluded that while post-stretching decreased the migration rate, heat-setting seems to boost this migration.

Migration of additive molecules in a polymer filament obtained by melt spinning: Influence of the fiber processing steps

Energy Technology Data Exchange (ETDEWEB)

Gesta, E. [Ingénierie des Matériaux Polymères - UMR CNRS 5223, Université de Lyon - Université Lyon 1, Bâtiment POLYTECH Lyon - 15 boulevard Latarjet, 69622, Villeurbanne (France); Intelligent Insect Control, 118 Chemin des Alouettes, Castelnau-le-Lez, 34170 (France); Skovmand, O., E-mail: osk@insectcontrol.net [Intelligent Insect Control, 118 Chemin des Alouettes, Castelnau-le-Lez, 34170 (France); Espuche, E., E-mail: eliane.espuche@univ-lyon1.fr; Fulchiron, R., E-mail: rene.fulchiron@univ-lyon1.fr [Ingénierie des Matériaux Polymères - UMR CNRS 5223, Université de Lyon - Université Lyon 1, Bâtiment POLYTECH Lyon - 15 boulevard Latarjet, 69622, Villeurbanne (France)

2015-12-17

The purpose of this study is to understand the influence of the yarn processing on the migration of additives molecules, especially insecticide, within polyethylene (PE) yarns. Yarns were manufactured in the laboratory focusing on three key-steps (spinning, post-stretching and heat-setting). Influence of each step on yarn properties was investigated using tensile tests, differential scanning calorimetry and wide-angle X-ray diffraction. The post-stretching step was proved to be critical in defining yarn mechanical and structural properties. Although a first orientation of polyethylene crystals was induced during spinning, the optimal orientation was only reached by post-stretching. The results also showed that the heat-setting did not significantly change these properties. The presence of additives crystals at the yarn surface was evidenced by scanning-electron microscopy. These studies performed at each yarn production step allowed a detailed analysis of the additives’ ability to migrate. It is concluded that while post-stretching decreased the migration rate, heat-setting seems to boost this migration.

Migration of additive molecules in a polymer filament obtained by melt spinning: Influence of the fiber processing steps

International Nuclear Information System (INIS)

Gesta, E.; Skovmand, O.; Espuche, E.; Fulchiron, R.

2015-01-01

The purpose of this study is to understand the influence of the yarn processing on the migration of additives molecules, especially insecticide, within polyethylene (PE) yarns. Yarns were manufactured in the laboratory focusing on three key-steps (spinning, post-stretching and heat-setting). Influence of each step on yarn properties was investigated using tensile tests, differential scanning calorimetry and wide-angle X-ray diffraction. The post-stretching step was proved to be critical in defining yarn mechanical and structural properties. Although a first orientation of polyethylene crystals was induced during spinning, the optimal orientation was only reached by post-stretching. The results also showed that the heat-setting did not significantly change these properties. The presence of additives crystals at the yarn surface was evidenced by scanning-electron microscopy. These studies performed at each yarn production step allowed a detailed analysis of the additives’ ability to migrate. It is concluded that while post-stretching decreased the migration rate, heat-setting seems to boost this migration

Development of fiber product recycling technology in fiscal 1998. Achievement report on developing woven product technology utilizing 'waste selvages' generated from weaving process; 1998 nendo sen'i seihin recycle gijutsu kaihatsu seika hokokusho. Seishoku no sai ni hasseisuru 'sutemimi' wo sairiyoshita orimono seihin gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Researches have been made to develop a technology to re-utilize 'waste selvages' generated from weaving process as weaving yarn, and recycle it into toiletry related products such as bath mats and toilet mats. In developing a technology to unify the waste selvage widths, such a research achievement was obtained that one side of the waste selvage width of 19 to 25 mm is most suitable for making the selvages into yarn, whereas the 'waste yarn standard' was established. In the waste selvage winding technology, development was achieved on a dedicated winder which is interlocked with the waste selvage roller on the yarn feeding side. In developing the technologies for waste selvage starching, twisting, and heating, a double twister that can handle very large yarn number counts was developed. For the winding device that can handle yarns of large counts, a re-winder was developed to rewind the yarn by rotating a dying bobbin of the up-twister system. In the weaving technology dealing large count yarns, the tension device and the pile forming device were developed. Twenty-seven kinds of prototype bath mats were fabricated through the experimental production, whose prospect of commercialization has come into the realization range. (NEDO)

The Influence of Three-Layer Knitted Fabrics’ Structure on Electrostatic and Comfort Properties

Directory of Open Access Journals (Sweden)

Sandra VARNAITĖ ŽURAVLIOVA

2013-12-01

Full Text Available In our times, when electricity and electrical devices are around us every day, it is very important to be protected from electrostatic discharge. The best protection from electric charge dissipation provides conductive textile materials. For the last few decades fine and flexible conductive yarns were developed, which ensure very good electrostatic properties. Unfortunately, due to their chemical nature, these yarns do not distinguish good comfort properties. The main purpose of development of such textiles is to determine the influence of conductive yarns and hollow fiber yarns arrangements in the middle layer of the three layer weft-knitted fabrics to electrostatic and comfort properties. So, in order to have flexible textile materials with good electrostatic and comfort properties, multifunctional three layer weft-knitted fabrics of combined pattern were designed and manufactured for this research work. Two groups of polyester based three layer knitted fabrics with different arrangement of conductive yarns (such as carbon core yarn and polyester silver coated yarn and polyester yarn of special design (Coolmax®, Thermolite® were investigated. The parameters of electrostatic characteristics, such as surface and vertical resistances as well as charge decay properties were measured. The results have showed that all tested fabrics have excellent shielding properties. The main influence on the electrostatic properties of tested fabrics has the arrangement of conductive carbon core yarns inserted in the knits. In order to evaluate the comfort of knitted fabrics the air permeability, hygroscopicity, time of absorption and drying degree of fabrics were evaluated. It was determined, that the values of comfort parameters depend on the quantity and distribution of Coolmax® and Thermolite® yarns in the fabrics.DOI: http://dx.doi.org/10.5755/j01.ms.19.4.2235

77 FR 16001 - Interim Procedures for Considering Requests Under the Commercial Availability Provision of the...

Science.gov (United States)

2012-03-19

..., fiber content, construction, yarn size, and finishing processes; and the classification of the product... specifications, including, if applicable, fiber content, construction, yarn size, and may include a finishing... requests to modify the list of fibers, yarns, or fabrics not available in commercial quantities in a timely...

Influence of Knits Structure on Flammability and Comfortability

Directory of Open Access Journals (Sweden)

Mikučionienė D.

2014-12-01

Full Text Available Investigations of the influence of the knit structure, i.e. the loop length and the number of yarns in a loop, on flammability and comfortability are presented in this paper. The investigations were carried out using single jersey knits from Delta TA 18 tex × 2 yarns with five variants of a loop length. Single yarn as well as folded yarn from two single yarns was used in the investigations. Comparison of the results of single-layer knits flammability and air permeability with those of multilayer packet was made. The results obtained show that an increase in the loop length of the knit increases their permeability to air and decreases the burning time as well as increase in the number of layers decreases the air permeability and increases the burning time. Moreover, the similar burning time with significantly different permeability to air can be achieved changing the basic knitting parameters, i.e. the loop length and/or the yarn linear density.

Micro-tomography based Geometry Modeling of Three-Dimensional Braided Composites

Science.gov (United States)

Fang, Guodong; Chen, Chenghua; Yuan, Shenggang; Meng, Songhe; Liang, Jun

2018-06-01

A tracking and recognizing algorithm is proposed to automatically generate irregular cross-sections and central path of braid yarn within the 3D braided composites by using sets of high resolution tomography images. Only the initial cross-sections of braid yarns in a tomography image after treatment are required to be calibrated manually as searching cross-section template. The virtual geometry of 3D braided composites including some detailed geometry information, such as the braid yarn squeezing deformation, braid yarn distortion and braid yarn path deviation etc., can be reconstructed. The reconstructed geometry model can reflect the change of braid configurations during solidification process. The geometry configurations and mechanical properties of the braided composites are analyzed by using the reconstructed geometry model.

EXPERIENCES IN THE AIR SPINNING TO MANUFACTURE MEDICAL DEVICES

Directory of Open Access Journals (Sweden)

MARSAL Feliu

2015-05-01

Full Text Available The work aims to determine, with scientific rigor, differences in key parameters of the yarns produced by conventional ring spinning systems, open-end and air spinning and its interrelation with the main parameters of those products that are intended for medical-sanitary sector. The experiences have been made in a Spanish company from short fibers sector that has three spinning systems, with tradition and prestige in world market, validating the results in Innotex Center laboratories of the Polytechnic University of Catalonia. Considering the results, it shows that the technology of manufacture of yarns by air is suitable for yarn, woven fabrics and knitting, structures to textile medical-sanitary application, by specific properties as well as enhanced competitiveness, due to the high production rate and shortened spinning process. The viscose yarns manufactured by air mass are more mass regular. The new DR parameter clearly indicates a better look of the finished fabric when we work with yarns produced by air technology.The significant reduction of the hairiness means less formation of loose fibres by friction, very important in the application of these yarns in the manufacture of textile structures for medical-sanitary use. Also no-table increase of about 15% in the absorption capacity of the fluids, especially water, from the yarns made by air. In the functionalization of fabrics obtained from spun yarn by air will need to apply a permanent smoothing.

The "Parachute" Technique: A Simple and Effective Single-Row Procedure to Achieve an Increased Contact Area Between the Cuff-Tendon and Its Footprint.

Science.gov (United States)

Natera, Luis; Consigliere, Paolo; Witney-Lagen, Caroline; Brugera, Juan; Sforza, Giuseppe; Atoun, Ehud; Levy, Ofer

2017-10-01

Many techniques of arthroscopic rotator cuff repair have been described. No significant differences in clinical outcomes or rerupture rates have been observed when comparing single-row with double-row methods. Not all single- and double-row repairs are the same. The details of the technique used are crucial. It has been shown that the suture-tendon interface is the weakest point of the reconstruction. Therefore, the biomechanical properties of rotator cuff repairs might be influenced more by the suture configuration than by the number of anchors or by the number of rows involved. Techniques that secure less amount of tendon over a smaller area of the healing zone might be expected to have higher failure rates. The way the sutures of the "parachute technique" are configured represents a quadruple mattress that increases the contact and pressure between the tendon and its footprint and increases the primary load to failure of the repair. We present a simple and effective single-row technique that involves the biomechanical and biological advantages related to the increased contact area and pressure between the cuff and its footprint.

The construction phase’s influence to the moving ability of cross-sections of woven structure

Science.gov (United States)

Inogamdjanov, D.; Daminov, A.; Kasimov, O.

2017-10-01

The purpose of this study is to work out bases to predict properties for single layer flat woven fabrics depending on changes of construction phases. A structural model of cross-section of single layered fabric is described based on the Pierce’s model. Form transformation of the yarn like straight, semi-arch and arch yarn is considered according to the alteration of yarn tension under the theory of Novikov. The value contributions to movement index of warp and weft yarn and their total moving ability in cross-sections at all structure phases of fabric are summarized.

Innovative monitoring of 3D warp interlock fabric during forming process

Science.gov (United States)

Dufour, C.; Jerkovic, I.; Wang, P.; Boussu, F.; Koncar, V.; Soulat, D.; Grancaric, A. M.; Pineau, P.

2017-10-01

The final geometry of 3D warp interlock fabric needs to be check during the 3D forming step to ensure the right locations of warp and weft yarns inside the final structure. Thus, a new monitoring approach has been proposed based on sensor yarns located in the fabric thickness. To ensure the accuracy of measurements, the observation of the surface deformation of the 3D warp interlock fabric has been joined to the sensor yarns measurements. At the end, it has been revealed a good correlation between strain measurement done globally by camera and locally performed by sensor yarns.

Molecular epidemiology of anthrax cases associated with recreational use of animal hides and yarn in the United States.

Directory of Open Access Journals (Sweden)

Chung K Marston

Full Text Available To determine potential links between the clinical isolate to animal products and their geographic origin, we genotyped (MLVA-8, MVLA-15, and canSNP analysis 80 environmental and 12 clinical isolates and 2 clinical specimens from five cases of anthrax (California in 1976 [n = 1], New York in 2006 [n = 1], Connecticut in 2007 [n = 2], and New Hampshire in 2009[n = 1] resulting from recreational handling of animal products. For the California case, four clinical isolates were identified as MLVA-8 genotype (GT 76 and in the canSNP A.Br.Vollum lineage, which is consistent with the Pakistani origin of the yarn. Twenty eight of the California isolates were in the A.Br.Vollum canSNP lineage and one isolate was in the A.Br. 003/004 canSNP sub-group. All 52 isolates and both clinical specimens related to the New York and Connecticut cases were MLVA-8 GT 1. The animal products associated with the NY and CT cases were believed to originate from West Africa, but no isolates from this region are available to be genotyped for comparison. All isolates associated with the New Hampshire case were identical and had a new genotype (GT 149. Isolates from the NY, CT and NH cases diverge from the established canSNP phylogeny near the base of the A.Br.011/009. This report illustrates the power of the current genotyping methods and the dramatically different epidemiological conditions that can lead to infections (i.e., contamination by a single genotype versus widespread contamination of numerous genotypes. These cases illustrate the need to acquire and genotype global isolates so that accurate assignments can be made about isolate origins.

A Wear Geometry Model of Plain Woven Fabric Composites

Directory of Open Access Journals (Sweden)

Gu Dapeng

2014-09-01

Full Text Available The paper g describes a model meant for analysis of the wear geometry of plain woven fabric composites. The referred model consists of a mathematical description of plain woven fabric based on Peirce’s model coupled with a stratified method for the solution of the wear geometry. The evolutions of the wear area ratio of weft yarn, warp yarn and matrix resin on the worn surface are simulated by MatLab software in combination of warp and weft yarn diameters, warp and weft yarn-to-yarn distances, fabric structure phases (SPs. By comparing theoretical and experimental results from the PTFE/Kevlar fabric wear experiment, it can be concluded that the model can present a trend of the component area ratio variations along with the thickness of fabric, but has a inherently large error in quantitative analysis as an idealized model.

Study of the effect of composition and construction of material on sub-bandage pressure during dynamic loading of a limb in vitro.

Science.gov (United States)

Kumar, Bipin; Das, Apurba; Alagirusamy, R

2013-01-01

Internal stress in a compression bandage wrapped over a limb in vitro is expected to reduce over time because of fatigue which may occur due to repetitive and prolonged variations in the extension of the bandage during posture change and exercise. This phenomenon may cause significant variation in the sub-bandage pressure over time. To examine the effect of composition and construction of material on the sub-bandage pressure variation over time in the dynamic state of a limb in the laboratory. Yarns comprising fibers of polyester, viscose, cotton and elastomeric yarn were used to prepare different knitted bandage samples having varying thread densities in the structure. A leg-segment prototype was used for the measurement of the interface pressure over a mannequin limb to analyse different bandages under similar dynamic conditions. The pressure drop in the dynamic state of the mannequin limb was greater than that in the static state. The mean pressure drop in 2 h in the dynamic state was greater by >30% for bandages made of pure cotton or viscose yarns than for bandages having elastomeric yarns in their structure. At the same applied tension, increasing the number of yarns per unit length in the bandage structure resulted in a smaller drop in pressure in the dynamic mode. Elastomeric yarn improves the elasticity and fatigue resistance of the bandage. Therefore, these yarns should be used in bandages to obtain sustained compression effects under dynamic conditions.

Development of superhydrophobic fabrics by surface fluorination and formation of CNT-induced roughness

Directory of Open Access Journals (Sweden)

Myoung Hee Shim

2015-03-01

Full Text Available Superhydrophobictextile material having self-cleaning function was developed by employing carbon nanotubes (CNTs and water-repellent agents.Hydrophobic fabrics were prepared on 100% polyester woven fabrics withvarious yarn diameters and yarn types. The wetting behavior of fabrics withdifferent treatments was compared for: siloxanerepellent, fluorocarbon repellent, and CNT added fluorocarbon repellent. Drawn textured yarn (DTY fabrics exhibited higher contactangle (CA than filament yarn fabrics due to the larger surface roughness contributed by the textured yarn. Fabrics treated with fluorocarbon presentedlarger CA and lower shedding angle than those treated with siloxane,because of the lower surface energy of fluorocarbon repellent. Specimens madeof 50 denier DTY and treated with CNT-Teflon AF® showed the mostsuperhydrophobic characteristics in the study, producing the static contactangle>150° and the shedding angle<15°. CNT on fabric surface contributedto the nano-scale surface roughness to hold the air traps like papillae oflotus leaf, giving superhydrophobic characteristics.DOI: http://dx.doi.org/10.5755/j01.ms.21.1.5762

感性製品設計のための繊維, 編織布の物理特性評価システムの開発

OpenAIRE

高寺, 政行; 清水, 義雄; 橋本, 稔; 乾, 滋; 上條, 正義; 堀場, 洋輔

2004-01-01

Development or fiber and fabric measurement system of physical property are being carried out in order to take KANSEI performance in textile design. Transverse compression characteristic of yarn and fabric is important factor influencing tactile evaluation of cloth. However, evaluation of transverse compression characteristic of yarn is not established and does not evaluate as compression modulus. In this study, evaluation of transverse compression characteristic of yarn and the relationship ...

Carbon nanotube torsional springs for regenerative braking systems

Science.gov (United States)

Liu, Sanwei; Martin, Corbin; Lashmore, David; Schauer, Mark; Livermore, Carol

2015-10-01

The modeling and demonstration of large stroke, high energy density and high power density torsional springs based on carbon nanotube (CNT) yarns is reported, as well as their application as energy-storing actuators for regenerative braking systems. An originally untwisted CNT yarn is cyclically loaded and unloaded in torsion, with the maximum rotation angle increasing incrementally until failure. The measured average extractable energy density values are 2.9 kJ kg-1  ±  1.2 kJ kg-1 and 3.4 kJ kg-1  ±  0.4 kJ kg-1 for 1-ply CNT yarns and 2-ply CNT yarns, respectively. Additionally, a regenerative braking system is demonstrated to capture the kinetic energy of a wheel and store it as elastic energy in twisted CNT yarns. When the yarn’s twist is released, the stored energy reaccelerates the wheel. The measured energy and mean power densities of the CNT yarns in the simple regenerative braking setup are on average 3.3 kJ kg-1 and 0.67 kW kg-1, respectively, with maximum measured values of up to 4.7 kJ kg-1 and 1.2 kW kg-1, respectively. A slightly lower energy density of up to 1.2 kJ kg-1 and a 0.29 kW kg-1 mean power density are measured for CNT yarns in a more complex setup that mimics a unidirectional rotating regenerative braking mechanism.

An integrated management tool for rockfall evaluation along transportation corridors: the ParaChute research project

Science.gov (United States)

Cloutier, Catherine; Locat, Jacques; Mayers, Mélanie; Noël, François; Turmel, Dominique; Jacob, Chantal; Dorval, Pierre; Bossé, François; Gionet, Pierre; Jaboyedoff, Michel

2016-04-01

Rockfall is a significant hazard along linear infrastructures due to the presence of natural and man-made rock slopes. Knowing where the problematic rockfalls source areas are is of primary importance to properly manage and mitigate the risk associated to rockfall along linear infrastructures. The aim of the ParaChute research project is to integrate various technologies into a workflow for rockfall characterization for such infrastructures, using a 220 km-long railroad as the study site which is located on Québec's North Shore, Canada. The objectives of this 3-year project which started in 2014 are: (1) to optimize the use of terrestrial, mobile and airborne laser scanners data into terrain analysis, structural geology analysis and rockfall susceptibility rating, (2) to further develop the use of unmanned aerial vehicles (UAV) for photogrammetry applied to rock cliff characterization, and (3) to integrate rockfall simulation studies into a rock slope classification system similar to the Rockfall Hazard Rating System. Firstly, based on laser scanner data and aerial photographs, the morpho-structural features of the terrain (genetic material, landform, drainage, etc.) are mapped. The result can be used to assess all types of mass movements. Secondly, to guide field work and decrease uncertainty of various parameters, systematic rockfall simulations and a first structural analysis are made from point clouds acquired by mobile and airborne laser scanner. The simulation results are used to recognize the rock slopes that have potentially problematic rockfall paths, meaning they could reach the linear infrastructure. Other rock slopes are not included in the inventory. Field work is carried out to validate and complete the rock slopes characterization previously made from remote sensing technique. Because some or parts of cliffs are not visible or accessible from the railroad, we are currently developing the use of photogrammetry by UAV in order to complete the

Carbon nanotube torsional springs for regenerative braking systems

International Nuclear Information System (INIS)

Liu, Sanwei; Martin, Corbin; Livermore, Carol; Lashmore, David; Schauer, Mark

2015-01-01

The modeling and demonstration of large stroke, high energy density and high power density torsional springs based on carbon nanotube (CNT) yarns is reported, as well as their application as energy-storing actuators for regenerative braking systems. An originally untwisted CNT yarn is cyclically loaded and unloaded in torsion, with the maximum rotation angle increasing incrementally until failure. The measured average extractable energy density values are 2.9 kJ kg −1   ±  1.2 kJ kg −1 and 3.4 kJ kg −1   ±  0.4 kJ kg −1 for 1-ply CNT yarns and 2-ply CNT yarns, respectively. Additionally, a regenerative braking system is demonstrated to capture the kinetic energy of a wheel and store it as elastic energy in twisted CNT yarns. When the yarn’s twist is released, the stored energy reaccelerates the wheel. The measured energy and mean power densities of the CNT yarns in the simple regenerative braking setup are on average 3.3 kJ kg −1 and 0.67 kW kg −1 , respectively, with maximum measured values of up to 4.7 kJ kg −1 and 1.2 kW kg −1 , respectively. A slightly lower energy density of up to 1.2 kJ kg −1 and a 0.29 kW kg −1 mean power density are measured for CNT yarns in a more complex setup that mimics a unidirectional rotating regenerative braking mechanism. (paper)

Summary of CPAS EDU Testing Analysis Results

Science.gov (United States)

Romero, Leah M.; Bledsoe, Kristin J.; Davidson, John.; Engert, Meagan E.; Fraire, Usbaldo, Jr.; Galaviz, Fernando S.; Galvin, Patrick J.; Ray, Eric S.; Varela, Jose

2015-01-01

The Orion program's Capsule Parachute Assembly System (CPAS) project is currently conducting its third generation of testing, the Engineering Development Unit (EDU) series. This series utilizes two test articles, a dart-shaped Parachute Compartment Drop Test Vehicle (PCDTV) and capsule-shaped Parachute Test Vehicle (PTV), both of which include a full size, flight-like parachute system and require a pallet delivery system for aircraft extraction. To date, 15 tests have been completed, including six with PCDTVs and nine with PTVs. Two of the PTV tests included the Forward Bay Cover (FBC) provided by Lockheed Martin. Advancements in modeling techniques applicable to parachute fly-out, vehicle rate of descent, torque, and load train, also occurred during the EDU testing series. An upgrade from a composite to an independent parachute simulation allowed parachute modeling at a higher level of fidelity than during previous generations. The complexity of separating the test vehicles from their pallet delivery systems necessitated the use the Automatic Dynamic Analysis of Mechanical Systems (ADAMS) simulator for modeling mated vehicle aircraft extraction and separation. This paper gives an overview of each EDU test and summarizes the development of CPAS analysis tools and techniques during EDU testing.

Superconductive transition metal carbonitride fibers and method for the preparation thereof

International Nuclear Information System (INIS)

Economy, J.; Mason, J.H.; Smith, W.D.

1976-01-01

Fine diameter continuous multifilament superconductor yarns comprising niobium carbonitride may be prepared. The fibers of which the yarn is composed possess a very high transition temperature (T/sub c/ of 17 0 K) combined with a good upper critical field (H/sub c2/ of 125 kG) and critical current density (J/sub c/ of 10 5 amps/cm 2 at 40 kG). This invention provides excellent superconductor materials in the form of continuous fine diameter multifilament yarn. 9 claims

INCOME DISTRIBUTIONAL IMPACTS OF TRADE POLICIES IN A MULTI-MARKET FRAMEWORK: A CASE IN PAKISTAN

OpenAIRE

Hudson, Darren; Ethridge, Don E.

2000-01-01

The impacts of using export taxes as a price control in a multi-market framework are explored using the cotton and yarn sectors in Pakistan as examples. Results show that the export tax on cotton increased domestic consumption and decreased exports of cotton in Pakistan, transferring income from cotton producers to yarn spinners and the government. There was a social loss to Pakistan in the cotton sector. The export tax on cotton increased domestic yarn production, consumption, exports, and i...

Preparation of unidirectional fiber reinforced tantalum carbide composites

International Nuclear Information System (INIS)

Newkirk, L.R.; Riley, R.E.; Sheinberg, H.; Valencia, F.A.; Wallace, T.C.

1979-01-01

A process is described for uniformly infiltrating 3000 filament carbon yarn with Ta and subsequent densification by hot pressing. Ta deposition rate is characterized as a function of deposition temperature, reactant flows, yarn pull rate, and coating chamber geometry for yarn pull rates from 2 to 50 m/h and Ta loadings from 40 to 350 wt % gain. Densification procedures for unidirectional pressings are described and data is presented which shows significant improvement in flexure strength over conventional TaC-C powder composites

Caracterização térmica de fios de poliaramida Characterization of aramid yarns

Directory of Open Access Journals (Sweden)

Nicolas T. Boukouvalas

2007-12-01

Full Text Available A poliaramida (aramida é um polímero de alto desempenho, cujas principais características são a elevada tenacidade, baixo alongamento e resistência ao calor. Devido ao desconhecimento do mercado em geral a respeito de materiais têxteis, metodologia de ensaios e a nomenclatura utilizada nesta família de materiais, invariavelmente ocorrem erros na escolha da qualidade do produto a adquirir. O uso de equipamentos inadequados para caracterização deste material pode levar a erros de interpretação. Este trabalho visa a melhor informar sobre este mercado, e discutir análises já realizadas. O gráfico tensão x deformação da poliaramida obtido em equipamento e garras corretas é linear, o que não ocorre se o equipamento de tração equipado com garras não for preparado para ensaios de tração de fios têxteis. Em análise termogravimétrica, verificou-se que a taxa de elevação de temperatura mais adequada é de aproximadamente 3 °C/min. A degradação da poliaramida se inicia a aproximadamente 510 °C, pela decomposição térmica das ligações simples, seguida da decomposição térmica dos anéis aromáticos a aproximadamente 525 ºC, sendo que a temperatura de degradação térmica completa ocorre a cerca de 575 °C.Polyaramid (aramid is a high performance polymer, whose main characteristics are its high tenacity, low elongation and good heat resistance. Owing to the lack of familiarity of the market with textile materials, methods of analysis and the nomenclature used for this family of materials, errors in the choice of the product quality are common. The inadequate use of equipment in the characterization of this material may lead to errors of interpretation. This work aims to inform about this market, and discuss results of previous analyses. A stress x strain graph of polyaramid is linear if obtained with adequate equipment and fixtures, which is not the case if the equipment and fixtures are not suitable for textile yarns

Mechanisms of degradation of cotton and effects of mercerization-stretching upon the course of these mechanisms. Pt. 3

Energy Technology Data Exchange (ETDEWEB)

Hebeish, A; Abou-Zeid, N Y; Shalaby, S E; El-Aref, A T; Waly, A; Abdel-Thalouth, I; Tawfik, M

1981-10-06

Changes in the physical as well as chemical structure of scoured and slack mercerized restretched (90-103% of original length) cotton yarns brought about by heat treatments and the effects of these on the strenght properties of the cotton yarn were investigated. No striking changes in copper number, carboxyl content, iodine sorption, degree of polymerization (P) and strenght properties were observed when the scoured and the mercerized yarns were heated at 160, 180, 200, and 210/sup 0/C for up to 10 min. On the contrary, with the exception of carboxyl content, marked changes in these properties were determined when heat treatment was carried out for up to 96 h and 5 h at 160/sup 0/C and 210/sup 0/C, respectively. However, the mercerized yarns retained higher strenghts in spite of higher degradation as compared to scoured yarn. The interrelationship between strenght and P as well as strength and percentage of bonds broken together with measurements of frequency of successive regions of high lateral order indicated that mercerized cotton exhibited a more uniform structure which improved the distribution of stress along the fibre.

Moisture Comfort and Antibacterial Properties of Elastic Warp-Knitted Fabrics

Directory of Open Access Journals (Sweden)

Yu Zhi-Cai

2015-03-01

Full Text Available Multifunction elastic warp-knitted fabrics were fabricated on a crochet machine with the use of metal composite yarns/viscose yarn and bamboo polyester/ crisscross-section polyester hybrid yarns as the front face and back face of the knitted fabric structure, respectively. We investigated the effect of the blend ratio of bamboo charcoal/ crisscross-section polyester multiply yarns on the fabric's moisture comfort properties, such as water vapour transmission (WVT, water evaporation rate (WER, and water absorbency. The results showed that blending ratio significantly influenced WVT and WER. Moreover, antibacterial activity of the elastic warp- knitted fabric was tested against Staphylococcus aureus and Escherichia coli in accordance with AATCC 90-2011. Finally, the extension- stress value curves were used to analyse the elastic stretching property, and the fabric exhibited greater breaking elongation and lower stress value in the walewise than in the weft direction.

Multiscale mechanics of the lateral pressure effect on enhancing the load transfer between polymer coated CNTs.

Science.gov (United States)

Yazdandoost, Fatemeh; Mirzaeifar, Reza; Qin, Zhao; Buehler, Markus J

2017-05-04

While individual carbon nanotubes (CNTs) are known as one of the strongest fibers ever known, even the strongest fabricated macroscale CNT yarns and fibers are still significantly weaker than individual nanotubes. The loss in mechanical properties is mainly because the deformation mechanism of CNT fibers is highly governed by the weak shear strength corresponding to sliding of nanotubes on each other. Adding polymer coating to the bundles, and twisting the CNT yarns to enhance the intertube interactions are both efficient methods to improve the mechanical properties of macroscale yarns. Here, we perform molecular dynamics (MD) simulations to unravel the unknown deformation mechanism in the intertube polymer chains and also local deformations of the CNTs at the atomistic scale. Our results show that the lateral pressure can have both beneficial and adverse effects on shear strength of polymer coated CNTs, depending on the local deformations at the atomistic scale. In this paper we also introduce a bottom-up bridging strategy between a full atomistic model and a coarse-grained (CG) model. Our trained CG model is capable of incorporating the atomistic scale local deformations of each CNT to the larger scale collect behavior of bundles, which enables the model to accurately predict the effect of lateral pressure on larger CNT bundles and yarns. The developed multiscale CG model is implemented to study the effect of lateral pressure on the shear strength of straight polymer coated CNT yarns, and also the effect of twisting on the pull-out force of bundles in spun CNT yarns.

Evaluation of Properties of Unidirectional Hemp/Polypropylene Composites: Influence of Fiber Content and Fiber/Matrix Interface Variables

DEFF Research Database (Denmark)

Plackett, David; Løgstrup Andersen, Tom; Lilholt, Hans

2002-01-01

Flament-wound textile hemp yarn was used in combination with unmodified or maleated polypropylene (PP) films to produce plates of unidirectional composites.......Flament-wound textile hemp yarn was used in combination with unmodified or maleated polypropylene (PP) films to produce plates of unidirectional composites....

Comfort and Functional Properties of Far-Infrared/Anion-Releasing Warp-Knitted Elastic Composite Fabrics Using Bamboo Charcoal, Copper, and Phase Change Materials

Directory of Open Access Journals (Sweden)

Ting-Ting Li

2016-02-01

Full Text Available Elastic warp-knitted composite fabrics with far-infrared emissivity and an anion-releasing property were prepared using bamboo charcoal (BC, copper (Cu, and phase-change material (PCM. The functional composite fabric, which was composed of self-made complex yarns with various twisting degrees and material composition, were created using a rotor twister and ring-spinning technique. The fabric structure was diversified by the feeding modes of weft yarn into a crochet-knitting machine. The twist number of complex yarns was optimized by tensile tenacity, twist contraction, and hairiness, and analysis showed that twisting at 12 twists per inch produced the highest tensile tenacity and appropriate twist contraction and hairiness. Comfort evaluation showed that the elastic composite fabrics with BC weft yarns exhibited higher water–vapor transmission rate and air permeability, reaching 876 g/m2∙ day and 73.2 cm3/s/cm2, respectively. Three structures of composite fabric with various weft yarns had >0.85 ε far-infrared emissivity and 350–420 counts/cm3 anion amount. The prepared elastic warp-knitted fabrics can provide a comfortable, dry, and breathable environment to the wearer and can thus be applied as health-care textiles in the future.

Studies on Tasar Cocoon Cooking Using Permeation Method

Science.gov (United States)

Javali, Uday C.; Malali, Kiran B.; Ramya, H. G.; Naik, Subhas V.; Padaki, Naveen V.

2018-02-01

Cocoon cooking is an important process before reeling of tasar silk yarn. Cooking ensures loosening of the filaments in the tasar cocoons thereby easing the process of yarn withdrawal during reeling process. Tasar cocoons have very hard shell and hence these cocoons need chemical cooking process to loosen the silk filaments. Attempt has been made in this article to study the effect of using vacuum permeation chamber for tasar cocoon cooking in order to reduce the cooking time and improve the quality of tasar silk yarn. Vacuum assisted permeation cooking method has been studied in this article on tasar daba cocoons for cooking efficiency, deflossing and reelability. Its efficiency has been evaluated with respect to different cooking methods viz, traditional and open pan cooking methods. The tasar silk produced after reeling process has been tested for fineness, strength and cohesion properties. Results indicate that permeation method of tasar cooking ensures uniform cooking with higher efficiency along with better reeling performance and improved yarn properties.

Multi Length Scale Finite Element Design Framework for Advanced Woven Fabrics

Science.gov (United States)

Erol, Galip Ozan

Woven fabrics are integral parts of many engineering applications spanning from personal protective garments to surgical scaffolds. They provide a wide range of opportunities in designing advanced structures because of their high tenacity, flexibility, high strength-to-weight ratios and versatility. These advantages result from their inherent multi scale nature where the filaments are bundled together to create yarns while the yarns are arranged into different weave architectures. Their highly versatile nature opens up potential for a wide range of mechanical properties which can be adjusted based on the application. While woven fabrics are viable options for design of various engineering systems, being able to understand the underlying mechanisms of the deformation and associated highly nonlinear mechanical response is important and necessary. However, the multiscale nature and relationships between these scales make the design process involving woven fabrics a challenging task. The objective of this work is to develop a multiscale numerical design framework using experimentally validated mesoscopic and macroscopic length scale approaches by identifying important deformation mechanisms and recognizing the nonlinear mechanical response of woven fabrics. This framework is exercised by developing mesoscopic length scale constitutive models to investigate plain weave fabric response under a wide range of loading conditions. A hyperelastic transversely isotropic yarn material model with transverse material nonlinearity is developed for woven yarns (commonly used in personal protection garments). The material properties/parameters are determined through an inverse method where unit cell finite element simulations are coupled with experiments. The developed yarn material model is validated by simulating full scale uniaxial tensile, bias extension and indentation experiments, and comparing to experimentally observed mechanical response and deformation mechanisms. Moreover

Aircrew Automated Escape Systems (AAES) In-Service Usage Data Analyses. Volume 2. Papers Presented at the Annual SAFE Symposium (21st), San Antonio, Texas, 5,6,7,8 November 1983.

Science.gov (United States)

1983-11-05

Workspace Incompatibility 3.D. Anthropometric Incompatibility 3.E. Confusion of Controls , Switches, etc. 3.1. Inadvertent Operation 3.K. Personal... Controls , Switches, Etc fK, fHVpo~a lo r%. Misread Inruet s F L. Hyperversta aetiton G~. VIskal Reiss icitots Duo ’to Striucture 0M. Dyttlaelsm H. Task...PARACHUTE______________ a.Parachute Canopy Release___________ " < bAutomatic Parachute Divestment Devices ____ c. 4-line release O .IU. . PAIRCRAFT BUty0

Extension of One-Dimensional Models for Hyperelastic String Structures under Coulomb Friction with Adhesion

Directory of Open Access Journals (Sweden)

Vladimir Shiryaev

2018-04-01

Full Text Available A stretching behavior of knitted and woven textiles is modeled. In our work, the yarns are modeled as one-dimensional hyperelastic strings with frictional contact. Capstan law known for Coulomb’s friction of yarns is extended to an additional adhesion due to gluing of filaments on the yarn surface or some chemical reaction. Two-step Newton’s method is applied for the solution of the large stretching with sliding evolution in the contact nodes. The approach is illustrated on a hysteresis of knitted textile and on the force-strain curve for a woven pattern and both compared with experimental effective curves.

An Investigation On Air and Thermal Transmission Through Knitted Fabric Structures Using the Taguchi Method

Directory of Open Access Journals (Sweden)

Ghosh Anindya

2017-06-01

Full Text Available Knitted fabrics have excellent comfort properties because of their typical porous structure. Different comfort properties of knitted fabrics such as air permeability, thermal absorptivity, and thermal conductivity depend on the properties of raw material and knitting parameters. In this paper, an investigation was done to observe the effect of yarn count, loop length, knitting speed, and yarn input tension in the presence of two uncontrollable noise factors on selected comfort properties of single jersey and 1×1 rib knitted fabrics using the Taguchi experimental design. The results show that yarn count and loop length have significant influence on the thermo-physiological comfort properties of knitted fabrics.

Moisture Responded Transformable Property Of Intelligent Coolness Knitted Fabrics For Sportswear Clothings

Directory of Open Access Journals (Sweden)

Ah Kim Hyun

2017-09-01

Full Text Available The present study examined the physical properties related to the intelligent coolness characteristics including the wearing comfort of Huvis elastic fiber (HEF knitted fabrics. For this purpose, three kinds of covered filament yarn specimens, such as PET-HEF, Aerocool-HEF, and PET-spandex, were prepared, and their knitted fabric specimens were made using these covered yarn specimens. These knitted fabric specimens were dyed at different dyeing temperatures and times to analyze the dyeing characteristics. The moisture absorption rate, drying, and hygral expansion of the three kinds of knitted fabric specimens were measured and compared with the yarn characteristics to determine the wearing comfort of HEF knitted fabrics.

Cotton/polyester and cotton/nylon warp knitted terry cloth: Why ...

African Journals Online (AJOL)

Administrator

1994:68) and has the added advantage of enhanced durability because of the synthetic component that can be incorporated into the structure (Kadolph &. Langford, 2002:41). In practice, the ground yarns of warp knitted terry cloth fabrics often differ in composi- tion to the yarns of the pile (Miller, 1992:109, Wooten,. 1979).

78 FR 11159 - Determination under the Textile and Apparel Commercial Availability Provision of the Dominican...

Science.gov (United States)

2013-02-15

....25 for fabrics, yarns, and fibers that the Parties to the CAFTA-DR Agreement have determined are not... States determines that a fabric, yarn, or fiber is not available in commercial quantities in a timely... consisting of a 3-layered fleece/ shell construction, woven outer layer and brushed inner layer, bonded with...

Studies on the suitability of HDPE material for gill nets

OpenAIRE

Subramania Pillai, N.; Boopendranath, M.R.; Kunjipalu, K.K.

1989-01-01

The suitability of HDPE yarn and HDPE twine in place of nylon for gill nets has been studied. As regards total catch nylon gill net is found to be better than HDPE nets. However, statistical analysis of the catch in respect of quality fishes shows that HDPE yarn nets are equally efficient as nylon nets.

Processing and Electromagnetic Shielding Properties of Multifunctional Metal Composite Knitted Fabric used as Socks

Directory of Open Access Journals (Sweden)

Yu Zhicai

2016-01-01

Full Text Available In this research, a type of bamboo charcoal polyester (BC-PET/antibacterial nylon(AN/stainless steel wire (SSW metal composite yarn was prepared with a hollow spindle spinning machine, which using the SSW as the core material, the BC-PET and AN as the outer and inner wrapped yarns, respectively. The wrapping numbers was set at 8.0turns/cm for the produced metal composite yarns. Furthermore, a type of plated knitted fabric was designed and produced by using the automatic jacquard knitting machine. The plated knitted fabric presents the BC-PET/AN/SSW metal composite yarn on the knitted fabric face and the crisscross-section polyester (CSP on the knit back. The effect of lamination numbers and angles on the electromagnetic shielding effectiveness (EMSE were discussed in this study. EMSE measurement showed that the lamination angles will influence the EMSE, but not affect the air permeability. Finally, a novel EM shielding socks was designed with the produced plated knitted fabric. Finally, the performance of thermal resistance and evaporation resistance was also test usingThe sweating guarded hot plate apparatus.

The properties of weft knitted fabric medical and preventive treatment action using eco-raw materials

Science.gov (United States)

Halavska, L.; Batrak, O.

2016-07-01

A new trend in the world is the clothing production using the new types of ecological raw materials application - milk, pineapple, coconut, hemp, banana, eucalyptus, clams, corn, bamboo, soya, nettle yarn. This makes it possible to create textile materials of new generation with unique antibacterial and antiseptic properties. Such materials have a positive preventive and sometimes therapeutic effect on people, and their health. Eco-raw materials clothing is able to protect the human body from the environment harmful effects: cold, heat, rain, dust, opportunely remove from underclothing layer the steam and gases, sweat; maintain in underclothing layer the necessary microclimate for normal organism functioning. Study of knitwear consumer properties, produced with eco-materials, is an urgent task of the world vector, directed on ecological environmental protection. This paper presents the research results of hygroscopicity and capillarity weft knitted fabrics, what knitted from different types of eco-raw materials: bamboo yarn, yarn containing soybean and nettle yarn. Character of influence of the liquid raising level changes depending on the experiment time and the knitting structure is revealed.

Torsional carbon nanotube artificial muscles.

Science.gov (United States)

Foroughi, Javad; Spinks, Geoffrey M; Wallace, Gordon G; Oh, Jiyoung; Kozlov, Mikhail E; Fang, Shaoli; Mirfakhrai, Tissaphern; Madden, John D W; Shin, Min Kyoon; Kim, Seon Jeong; Baughman, Ray H

2011-10-28

Rotary motors of conventional design can be rather complex and are therefore difficult to miniaturize; previous carbon nanotube artificial muscles provide contraction and bending, but not rotation. We show that an electrolyte-filled twist-spun carbon nanotube yarn, much thinner than a human hair, functions as a torsional artificial muscle in a simple three-electrode electrochemical system, providing a reversible 15,000° rotation and 590 revolutions per minute. A hydrostatic actuation mechanism, as seen in muscular hydrostats in nature, explains the simultaneous occurrence of lengthwise contraction and torsional rotation during the yarn volume increase caused by electrochemical double-layer charge injection. The use of a torsional yarn muscle as a mixer for a fluidic chip is demonstrated.

Determining Effective Thermal Conductivity of Fabrics by Using Fractal Method

Science.gov (United States)

Zhu, Fanglong; Li, Kejing

2010-03-01

In this article, a fractal effective thermal conductivity model for woven fabrics with multiple layers is developed. Structural models of yarn and plain woven fabric are derived based on the fractal characteristics of macro-pores (gap or channel) between the yarns and micro-pores inside the yarns. The fractal effective thermal conductivity model can be expressed as a function of the pore structure (fractal dimension) and architectural parameters of the woven fabric. Good agreement is found between the fractal model and the thermal conductivity measurements in the general porosity ranges. It is expected that the model will be helpful in the evaluation of thermal comfort for woven fabric in the whole range of porosity.

A Prospective Investigation of Injury Incidence and Risk Factors Among Army Recruits in Combat Engineer Training

Science.gov (United States)

2013-03-05

Sports 1997, 7:304–311. 23. Knapik JJ, Spiess A, Swedler D, Grier T, Darakjy S, Amoroso P, Jones BH: Injury risk factors in parachuting and...reducing parachute-related ankle injuries. Med Sci Sports Exerc 2004, 36:S312. 26. Knapik JJ, Grier T, Spiess A, Swedler DI, Hauret KG, Graham B, Yoder...Knapik JJ, Spiess A, Darakjy S, Grier T, Manning F, Livingstone E, Swedler D, Amoroso P, Jones BH: Risk factors for parachute injuries and comments about

Edgar Pask and his physiological research--an unsung hero of World War Two.

Science.gov (United States)

Enever, G

2011-03-01

Edgar Pask died in 1966 at the age of 53. He was the Professor of Anaesthesia in Newcastle upon Tyne, and a quiet and unassuming man. But during the Second World War he had been involved in a number of dangerous and remarkable experiments; these included investigating the effects of acute hypoxia related to high altitude parachute descents, resuscitation techniques and the effectiveness of lifejackets.

Etude de l'effet du vieillissement sur les proprietes d'un tissu en melange KevlarRTM-PBI utilise dans le revetement exterieur des habits de protection contre le feu

Science.gov (United States)

Arrieta, Carlos

The aim of this work is to study and model the effect of three aging factors, temperature, humidity and light radiation, on the properties of a fabric made of a blend of KevlarRTM and PBI fibers frequently used to manufacture fire-protective garments. Accelarated-aging treatments carried out at carefully chosen conditions for the three factors resulted in a sizeable loss of mechanical performance. The breaking force of both the fabric and the yarns extracted from it decreases to less than 50% after one month of continuous exposure. X-ray diffraction (XRD) tests performed on thermally-aged samples indicated an increase of the crystallinity of the fabric, whereas the disappearance of Raman spectral lines suggested instead a reduction of the crystallinity following thermal aging. To explain these seemingly contradictory results, a hypothesis was introduced, stating that two different processes occurred simultaneously during thermal aging. The first one, an increase of size of the crystallites in the direction of the fibers' axis, accounted for the increase in crystallinity observed in XRD tests. The second one, an increase in the gap separating lamellar crystallites that causes a non-measurable reduction of the crystallinity of the sample, was highlighted by the Raman analyses. The results of the dielectric spectroscopy analyses carried out on thermally-aged samples confirmed the XRD results showing a significant change in the Kevlar's morphology during thermal aging. Despite the important decrease of the breaking force that ensued thermal aging, no evidence of a chemical structure modification of KevlarRTM was found. On the other hand, differential thermal analyses conducted on thermally aged fabric samples indicated a reduction of the glass transition temperature of the other component of the blend, namely the PBI, a fact that suggests a decrease of molecular weight after thermal aging. Infrared spectroscopy analyses performed on samples exposed to high humidity

Electrically controllable twisted-coiled artificial muscle actuators using surface-modified polyester fibers

Science.gov (United States)

Park, Jungwoo; Yoo, Ji Wang; Seo, Hee Won; Lee, Youngkwan; Suhr, Jonghwan; Moon, Hyungpil; Koo, Ja Choon; Ryeol Choi, Hyouk; Hunt, Robert; Kim, Kwang Jin; Kim, Soo Hyun; Nam, Jae-Do

2017-03-01

As a new class of thermally activated actuators based on polymeric fibers, we investigated polyethylene terephthalate (PET) yarns for the development of a twisted-coiled polymer fiber actuator (TCA). The PET yarn TCA exhibited the maximum linear actuation up to 8.9% by external heating at above the glass transition temperature, 160 °C-180 °C. The payload of the actuator was successfully correlated with the preload and training-load conditions by an empirical equation. Furthermore, the PET-based TCA was electrically driven by Joule heating after the PET surface was metallization with silver. For the fast and precise control of PET yarn TCA, electroless silver plating was conducted to form electrical conductive layers on the PET fiber surface. The silver plated PET-based TCA was tested by Joule heating and the tensile actuation was increased up to 12.1% (6 V) due to the enhanced surface hardness and slippage of PET fibers. Overall, silver plating of the polymeric yarn provided a fast actuation speed and enhanced actuation performance of the TCA actuator by Joule heating, providing a great potential for being used in artificial muscle for biomimetic machines including robots, industrial actuators and powered exoskeletons.

Investigation of Heating Behaviour of E-textile Structures

OpenAIRE

H. Sezgin; S. Kursun Bahadır; Y. E. Boke; F. Kalaoğlu

2015-01-01

By textile science incorporating with electronic industry, developed textile products start to take part in different areas such as industry, military, space, medical etc. for health, protection, defense, communication and automation. Electronic textiles (e-textiles) are fabrics that contain electronics and interconnections with them. In this study, two types of base yarns (cotton and acrylic) and three types of conductive steel yarns with different linear resistance valu...

Moisture management properties of plain knitted fabrics made of natural and regenerated cellulose fibres

Directory of Open Access Journals (Sweden)

Novaković Milada S.

2015-01-01

Full Text Available Moisture management is a complicated process which is known to be influenced by a variety of fabric characteristics such as fibre nature (hydrophilic or hydrophobic, porosity and thickness. There are different aspects of the moisture management properties of textile materials since water transport in textile materials can be in the form of liquid and vapour. The ability of textile materials to transfer water vapour allows the human body to keep thermal balance due to evaporation. With stronger physical activity of a person when the body produces a large amount of heat, the skin perspiration increases (in order to regulate the body temperature and liquid sweat should be taken from the skin, otherwise it will worsen the sense of comfort. The aim of this research was to investigate the factors influencing moisture management properties of plain knitted fabrics at the three scale levels, i.e. microscopic (fibre type, mesoscopic (yarn geometry and macroscopic (fabric porosity levels. Plain knitted fabrics were produced from the two-assembled hemp, cotton and viscose yarns under controlled conditions so as to be comparable in basic construction characteristics, but varying in yarns geometry. Evaporative resistance test reflecting vapour transport and water distribution test reflecting liquid transport in the knitted fabrics were conducted. To determine the statistical importance of the results, analysis of variance (ANOVA was applied. As a consequence of the geometry and deformation behaviour of the fibres used and spinning techniques applied, the yarns differed in both packing density and surface geometry, thus determining the pore distribution. Due to loose structure of the cotton yarn, the cotton knitted fabric was characterised by the lowest free open surface (macroporosity exhibiting the lowest both water vapour and liquid permeability. Although having the highest macroporosity, the water vapour and liquid transport capability of the hemp knitted

EVALUATION OF EFFECTIVE PROPERTIES OF BASALT TEXTILE REINFORCED CERAMIC MATRIX COMPOSITES

Directory of Open Access Journals (Sweden)

Soňa Valentová

2017-11-01

Full Text Available The present paper is concerned with the analysis of a ceramic matrix composite, more specifically the plain weave textile fabric composite made of basalt fibers embedded into the pyrolyzed polysiloxane matrix. Attention is paid to the determination of effective elastic properties of the yarn via homogenization based on the Mori-Tanaka averaging scheme and the 1st order numerical homogenization method adopting a suitable representative computational model. The latter approach is then employed to simulate the response of the yarn when loaded beyond the elastic limits. The required mechanical properties of individual material phases are directly measured using nanoindentation with in-build scanning probe microscopy. Applicability of the proposed computational methodology is supported by the analysis of a unidirectional fibrous composite, representing the yarn, subjected to a macroscopically uniform strain.

Use of a ring-shaped, passively stable, superconducting magnetic bearing in the ring spinning process; Einsatz eines ringfoermigen, passiv stabilen, supraleitenden Magnetlagers im Ringspinnprozess

Energy Technology Data Exchange (ETDEWEB)

Berger, Anne; Sparing, Maria; Berger, Dietmar; Fuchs, Guenter; Schultz, Ludwig [IFW Dresden (Germany). Inst. fuer Metallische Werkstoffe; Hossain, Mahmud; Abdkader, Anwar; Cherif, Chokri [TU Dresden (Germany). ITM

2015-07-01

For the integration of a superconducting magnetic bearing in a ring spinning machine a LN{sub 2} continuous flow cryostat was developed, which is needed to cool the superconductor below its transition temperature of ∝91 K and simultaneously ensures that the spinning process takes place at room temperature. The ring spinning process is the most widely used process for spinning yarn. In this case, a loose fiber connection is first stretched in a roller system, then twisted by the so-called spinning ring-ring traveler system, and finally wound on a spindle. The spinning ring is a circular guide, which is mounted around the spindle. On this the ring traveler rotates as yarn guide. The yarn is driven by the rotation of the spindle and there is a balloon-shaped movement of the yarn which results the twist. The productivity of the process is limited by the systematic frictional heat between the yarn, spinning ring and ring travelers. This leads at high speeds to yarn breakage and limits the maximum spindle speed depending on the type of fiber to a maximum of 25,000 U/min. To increase the speed and thus the productivity of the process, the conventional spinning ring-ring rotor system is replaced by a superconducting magnetic bearing. Here floats a NdFeB permanent magnet passively stable over the LN{sub 2} cooled ceramic high-temperature superconductor YBa{sub 2}Cu{sub 3}O{sub 7-x}. Driven by the yarn the permanent magnet rotates, thus ensuring the necessary balloon-shaped yarn movement to twist. Such a bearing has been successfully tested in a ring spinning machine. Preliminary results show a similar yarn quality. [German] Fuer die Integration eines supraleitenden Magnetlagers in eine Ringspinnmaschine wurde ein LN{sub 2}-Durchflusskryostat entwickelt, der noetig ist, um den Supraleiter unter seine Sprungtemperatur von ∝91 K zu kuehlen und gleichzeitig dafuer sorgt, dass der Spinnprozess bei Raumtemperatur ablaeuft. Der Ringspinnprozess ist der am weitesten verbreitete

Studies on Plant Population and Stand Establishment Techniques for Increasing Productivity of Rice in Dera Ismail Khan, Pakistan

Directory of Open Access Journals (Sweden)

Mohammad Safdar BALOCH

2007-06-01

Full Text Available Rice production in Pakistan is constraint by many factors pertaining to prevalent planting techniques. A research on the feasibility of new planting techniques (direct seeding on flat, transplanting on flat, direct seeding on ridges, transplanting on ridges and parachute planting in transplanted and direct wet-seeded rice was undertaken at Dera Ismail Khan region of Pakistan's North West Frontier Province during 2002 and 2003. Among the planting techniques, the best performance for the yield formation and economic evaluation was noted for transplanting on flat during both years. Chinese parachute planting technology also showed very promising results in most of the parameters. Direct seeding on ridges could not excel transplanting on flat and parachute planting during both cropping seasons. The findings concluded the feasibility of parachute planting technology along with traditional rice transplanting on flat over all other planting techniques being practiced in the area.

Orion Multi-Purpose Crew Vehicle Solving and Mitigating the Two Main Cluster Pendulum Problem

Science.gov (United States)

Ali, Yasmin; Sommer, Bruce; Troung, Tuan; Anderson, Brian; Madsen, Christopher

2017-01-01

The Orion Multi-purpose Crew Vehicle (MPCV) Orion spacecraft will return humans from beyond earth's orbit, including Mars and will be required to land 20,000 pounds of mass safely in the ocean. The parachute system nominally lands under 3 main parachutes, but the system is designed to be fault tolerant and land under 2 main parachutes. During several of the parachute development tests, it was observed that a pendulum, or swinging, motion could develop while the Crew Module (CM) was descending under two parachutes. This pendulum effect had not been previously predicted by modeling. Landing impact analysis showed that the landing loads would double in some places across the spacecraft. The CM structural design limits would be exceeded upon landing if this pendulum motion were to occur. The Orion descent and landing team was faced with potentially millions of dollars in structural modifications and a severe mass increase. A multidisciplinary team was formed to determine root cause, model the pendulum motion, study alternate canopy planforms and assess alternate operational vehicle controls & operations providing mitigation options resulting in a reliability level deemed safe for human spaceflight. The problem and solution is a balance of risk to a known solution versus a chance to improve the landing performance for the next human-rated spacecraft.

Woven electrochemical fabric-based test sensors (WEFTS): a new class of multiplexed electrochemical sensors.

Science.gov (United States)

Choudhary, Tripurari; Rajamanickam, G P; Dendukuri, Dhananjaya

2015-05-07

We present textile weaving as a new technique for the manufacture of miniature electrochemical sensors with significant advantages over current fabrication techniques. Biocompatible silk yarn is used as the material for fabrication instead of plastics and ceramics used in commercial sensors. Silk yarns are coated with conducting inks and reagents before being handloom-woven as electrodes into patches of fabric to create arrays of sensors, which are then laminated, cut and packaged into individual sensors. Unlike the conventionally used screen-printing, which results in wastage of reagents, yarn coating uses only as much reagent and ink as required. Hydrophilic and hydrophobic yarns are used for patterning so that sample flow is restricted to a small area of the sensor. This simple fluidic control is achieved with readily available materials. We have fabricated and validated individual sensors for glucose and hemoglobin and a multiplexed sensor, which can detect both analytes. Chronoamperometry and differential pulse voltammetry (DPV) were used to detect glucose and hemoglobin, respectively. Industrial quantities of these sensors can be fabricated at distributed locations in the developing world using existing skills and manufacturing facilities. We believe such sensors could find applications in the emerging area of wearable sensors for chemical testing.

Carded Tow Real-Time Color Assessment: A Spectral Camera-Based System

Directory of Open Access Journals (Sweden)

Rocco Furferi

2016-08-01

Full Text Available One of the most important parameters to be controlled during the production of textile yarns obtained by mixing pre-colored fibers, is the color correspondence between the manufactured yarn and a given reference, usually provided by a designer or a customer. Obtaining yarns from raw pre-colored fibers is a complex manufacturing process entailing a number of steps such as laboratory sampling, color recipe corrections, blowing, carding and spinning. Carding process is the one devoted to transform a “fuzzy mass” of tufted fibers into a regular mass of untwisted fibers, named “tow”. During this process, unfortunately, the correspondence between the color of the tow and the target one cannot be assured, thus leading to yarns whose color differs from the one used for reference. To solve this issue, the main aim of this work is to provide a system able to perform a spectral camera-based real-time measurement of a carded tow, to assess its color correspondence with a reference carded fabric and, at the same time, to monitor the overall quality of the tow during the carding process. Tested against a number of differently colored carded fabrics, the proposed system proved its effectiveness in reliably assessing color correspondence in real-time.

Non-destructive X-ray examination of weft knitted wire structures

Science.gov (United States)

Obermann, M.; Ellouz, M.; Aumann, S.; Martens, Y.; Bartelt, P.; Klöcker, M.; Kordisch, T.; Ehrmann, A.; Weber, M. O.

2016-07-01

Conductive yarns or wires are often integrated in smart textiles to enable data or energy transmission. In woven fabrics, these conductive parts are fixed at defined positions and thus protected from external loads. Knitted fabrics, however, have relatively loose structures, resulting in higher impacts of possible mechanical forces on the individual yarns. Hence, metallic wires with smaller diameters in particular are prone to break when integrated in knitted fabrics. In a recent project, wires of various materials including copper, silver and nickel with diameters varying between 0.05 mm and 0.23 mm were knitted in combination with textile yarns. Hand flat knitting machines of appropriate gauges were used to produce different structures. On these samples, non-destructive examinations, using an industrial X-ray system Seifert x|cube (225 kV) equipped with a minifocus X-ray tube, were carried out, directly after knitting as well as after different mechanical treatments (tensile, burst, and washing tests). In this way, structural changes of the stitch geometry could be visualized before failure. In this paper, the loop geometries in the knitted fabrics are depicted depending on knitted structures, wire properties and the applied mechanical load. Consequently, it is shown which metallic wires and yarns are most suitable to be integrated into knitted smart textiles.

DRAPING SIMULATION OF WOVEN FABRICS

Energy Technology Data Exchange (ETDEWEB)

Rodgers, William [General Motors LLC; Jin, Xiaoshi [ESI Group NA; Zhu, Jiang [Optimal CAE; Wathen, Terrence [General Motors LLC; Doroudian2, Mark [ESI Group NA; Aitharaju, Venkat [General Motors LLC

2016-09-07

Woven fabric composites are extensively used in molding complex geometrical shapes due to their high conformability compared to other fabrics. Preforming is an important step in the overall process, where the two-dimensional fabric is draped to become the three-dimensional shape of the part prior to resin injection. During preforming, the orientation of the yarns may change significantly compared to the initial orientations. Accurate prediction of the yarn orientations after molding is important for evaluating the structural performance of the final part. This paper presents a systematic investigation of the angle changes during the preform operation for carbon fiber twill and satin weave fabrics. Preforming experiments were conducted using a truncated pyramid mold geometry designed and fabricated at the General Motors Research Laboratories. Predicted results for the yarn orientations were compared with experimental results and good agreement was observed

Knitting Technologies And Tensile Properties Of A Novel Curved Flat-Knitted Three-Dimensional Spacer Fabrics

Directory of Open Access Journals (Sweden)

Li Xiaoying

2015-09-01

Full Text Available This paper introduces a knitting technique for making innovative curved three-dimensional (3D spacer fabrics by the computer flat-knitting machine. During manufacturing, a number of reinforcement yarns made of aramid fibres are inserted into 3D spacer fabrics along the weft direction to enhance the fabric tensile properties. Curved, flat-knitted 3D spacer fabrics with different angles (in the warp direction were also developed. Tensile tests were carried out in the weft and warp directions for the two spacer fabrics (with and without reinforcement yarns, and their stress–strain curves were compared. The results showed that the reinforcement yarns can reduce the fabric deformation and improve tensile stress and dimensional stability of 3D spacer fabrics. This research can help the further study of 3D spacer fabric when applied to composites.

The Effect Of Weave Construction On Tear Strength Of Woven Fabrics

Directory of Open Access Journals (Sweden)

Eryuruk Selin Hanife

2015-09-01

Full Text Available The tear strength of a woven fabric is very important, since it is more closely related to serviceability of the fabric. Tearing strength of the fabrics depend on the mobility of the yarn within the fabric structure. In this study, the tearing strength of four types of fabrics warp rib, weft rib, ripstop and plain weave were analysed, which were produced in different densities and with filament and texturised polyester yarns.

Dyeing studies with henna and madder: A research on effect of tin (II) chloride mordant

OpenAIRE

Yusuf, Mohd; Shahid, Mohammad; Khan, Mohd Ibrahim; Khan, Shafat Ahmad; Khan, Mohd Ali; Mohammad, Faqeer

2015-01-01

The present paper deals with the application of natural dyes extracted from powdered henna (Lawsonia inermis) leaves and madder (Rubia cordifolia) roots on woolen yarn and assessment of effect of stannous chloride mordant on dyeability, color characteristics, fastness properties and antifungal activity of dyed woolen yarn. Sixteen shades have been developed for the characterization of their color characteristics and fastness properties. The color strength (K/S value) has been found to be very...

Paratrooper's ankle fracture: posterior malleolar fracture.

Science.gov (United States)

Young, Ki Won; Kim, Jin-su; Cho, Jae Ho; Kim, Hyung Seuk; Cho, Hun Ki; Lee, Kyung Tai

2015-03-01

We assessed the frequency and types of ankle fractures that frequently occur during parachute landings of special operation unit personnel and analyzed the causes. Fifty-six members of the special force brigade of the military who had sustained ankle fractures during parachute landings between January 2005 and April 2010 were retrospectively analyzed. The injury sites and fracture sites were identified and the fracture types were categorized by the Lauge-Hansen and Weber classifications. Follow-up surveys were performed with respect to the American Orthopedic Foot and Ankle Society ankle-hindfoot score, patient satisfaction, and return to preinjury activity. The patients were all males with a mean age of 23.6 years. There were 28 right and 28 left ankle fractures. Twenty-two patients had simple fractures and 34 patients had comminuted fractures. The average number of injury and fractures sites per person was 2.07 (116 injuries including a syndesmosis injury and a deltoid injury) and 1.75 (98 fracture sites), respectively. Twenty-three cases (41.07%) were accompanied by posterior malleolar fractures. Fifty-five patients underwent surgery; of these, 30 had plate internal fixations. Weber type A, B, and C fractures were found in 4, 38, and 14 cases, respectively. Based on the Lauge-Hansen classification, supination-external rotation injuries were found in 20 cases, supination-adduction injuries in 22 cases, pronation-external rotation injuries in 11 cases, tibiofibular fractures in 2 cases, and simple medial malleolar fractures in 2 cases. The mean follow-up period was 23.8 months, and the average follow-up American Orthopedic Foot and Ankle Society ankle-hindfoot score was 85.42. Forty-five patients (80.36%) reported excellent or good satisfaction with the outcome. Posterior malleolar fractures occurred in 41.07% of ankle fractures sustained in parachute landings. Because most of the ankle fractures in parachute injuries were compound fractures, most cases had to

Sensation seeking in males involved in recreational high risk sports

OpenAIRE

M Guszkowska; A Bołdak

2010-01-01

The study examined sensation seeking intensity level in males involved in recreational high risk sports and investigated whether its level depends on type of sport practised. Additionally, in case of parachutists, sport experience of study participants were scrutinised with regard to its possible impact on the level of sensation seeking.The research involved 217 males aged 17 to 45, practising recreational high risk sports, namely: parachuting (n=98); wakeboarding (n=30); snowboarding (n=30);...

Facilitators of community participation in an Aboriginal sexual health promotion initiative.

Science.gov (United States)

Hulme Chambers, Alana; Tomnay, Jane; Stephens, Kylie; Crouch, Alan; Whiteside, Mary; Love, Pettina; McIntosh, Leonie; Waples Crowe, Peter

2018-04-01

Community participation is a collaborative process aimed at achieving community-identified outcomes. However, approaches to community participation within Aboriginal health promotion initiatives have been inconsistent and not well documented. Smart and Deadly was a community-led initiative to develop sexual health promotion resources with young Aboriginal people in regional Victoria, Australia. The principles of community-centred practice, authentic participatory processes and respect for the local cultural context guided the initiative. The aim of this article is to report factors that facilitated community participation undertaken in the Smart and Deadly initiative to inform future projects and provide further evidence in demonstrating the value of such approaches. A summative evaluation of the Smart and Deadly initiative was undertaken approximately 2 years after the initiative ended. Five focus groups and 13 interviews were conducted with a purposive sample of 32 participants who were involved with Smart and Deadly in one of the following ways: project participant, stakeholder or project partner, or project developer or designer. A deductive content analysis was undertaken and themes were compared to the YARN model, which was specifically created for planning and evaluating community participation strategies relating to Aboriginal sexual health promotion. A number of factors that facilitated community participation approaches used in Smart and Deadly were identified. The overarching theme was that trust was the foundation upon which the facilitators of community participation ensued. These facilitators were cultural safety and cultural literacy, community control, and legacy and sustainability. Whilst the YARN model was highly productive in identifying these facilitators of community participation, the model did not have provision for the element of trust between workers and community. Given the importance of trust between the project team and the Aboriginal

A Study on the Effect of Pin Density on Stationary Flats and its Setting on Carding Quality

Directory of Open Access Journals (Sweden)

Madan Lal Regar

2017-03-01

Full Text Available Carding is the most vital process in spinning, which infl uences the sliver quality and the resulting yarn characteristics. The eff ect of carding on single fibre and bundle fibre properties were studied by employing advanced fibre information system (AFIS and diff erences in properties are reported. For a good quality yarn, the process parameters and setting in the carding are needed to be selected properly. The paper presents the results due to the effect of points per square inch (PPSI in stationary flats of licker-in side (SFL. The effect of setting between the flats and cylinder was also studied. The sample was prepared using LMW spinning line using LC-333 carding machine. After regulatory changing the PPSI in SFL, the neps in the carded sliver were reduced. The experimentation led to the reductions in the total imperfection in yarn.

Dyeing studies with henna and madder: A research on effect of tin (II chloride mordant

Directory of Open Access Journals (Sweden)

Mohd Yusuf

2015-01-01

Full Text Available The present paper deals with the application of natural dyes extracted from powdered henna (Lawsonia inermis leaves and madder (Rubia cordifolia roots on woolen yarn and assessment of effect of stannous chloride mordant on dyeability, color characteristics, fastness properties and antifungal activity of dyed woolen yarn. Sixteen shades have been developed for the characterization of their color characteristics and fastness properties. The color strength (K/S value has been found to be very good in all dyed woolen yarn samples. The color fastness with respect to light exposure, washing and rubbing was quite satisfactory for both henna as well as madder dyed samples. Henna leaves extract was found very effective against Candida glabrata both in solution as well as after application on wool substrate but no antifungal activity is reported in case of madder both in solution as well as on wool substrate.

Electromagnetic absorption behaviour of ferrite loaded three phase carbon fabric composites

Science.gov (United States)

Jagatheesan, Krishnasamy; Ramasamy, Alagirusamy; Das, Apurba; Basu, Ananjan

2018-02-01

This article investigates the electromagnetic absorption behaviours of carbon helical yarn fabric reinforced composites and manganese-zinc (Mn-Zn) ferrite particles loaded 3 phase fabric composites. A carbon helical yarn having stainless steel core was prepared and made into single jersey knitted fabric. The composite was prepared by sandwiching a fabric with polypropylene films and thermal pressed. The absorption values of helical yarn fabric composite was observed to be less in the C band region (4-8 GHz). For improving the absorption coefficients of composite, Mn-Zn ferrite particles were dispersed in the polypropylene (PP) composite. The ferrite loaded PP composites exhibited better permittivity and permeability values, hence the absorption loss of the composite was improved. The helical yarn fabric reinforced with Mn-Zn ferrite/PP composite showed larger absorption coefficients than virgin PP/fabric composite. The change in thermal stability and particle size distribution in the Mn-Zn ferrite/PP composite was also analyzed. At higher ferrite concentration, bimodal particle distribution was observed which increased the conductivity and shielding effectiveness (SE) of the composite. In addition, complex permittivity value was also increased for higher incident frequency (4-8 GHz). As the ferrite content increases, the dielectric loss and magnetic permeability of PP/ferrite increases due to increased magnetic loss. Hence, ferrite loaded PP composite showed the total SE of -14.2 dB with the absorption coefficients of 0.717. The S1C7 fabric composite having ferrite dispersion showed the better absorption loss and lower reflection coefficient of 14.2 dB and 0.345 respectively compared to virgin PP/helical yarn fabric composite. The increasing ferrite content (45 wt%) improved the absorption loss and total SE. Though, ferrite based fabric composite exhibits moderate absorptive shielding, it can be used as shielding panels in the electronic industries.

Chemical vapor deposited fiber coatings and chemical vapor infiltrated ceramic matrix composites

Energy Technology Data Exchange (ETDEWEB)

Kmetz, M.A.

1992-01-01

Conventional Chemical Vapor Deposition (CVD) and Organometallic Chemical Vapor Deposition (MOCVD) were employed to deposit a series of interfacial coatings on SiC and carbon yarn. Molybdenum, tungsten and chromium hexacarbonyls were utilized as precursors in a low temperature (350[degrees]C) MOCVD process to coat SiC yarn with Mo, W and Cr oxycarbides. Annealing studies performed on the MoOC and WOC coated SiC yarns in N[sub 2] to 1,000[degrees]C establish that further decomposition of the oxycarbides occurred, culminating in the formation of the metals. These metals were then found to react with Si to form Mo and W disilicide coatings. In the Cr system, heating in N[sub 2] above 800[degrees]C resulted in the formation of a mixture of carbides and oxides. Convention CVD was also employed to coat SiC and carbon yarn with C, Bn and a new interface designated BC (a carbon-boron alloy). The coated tows were then infiltrated with SiC, TiO[sub 2], SiO[sub 2] and B[sub 4]C by a chemical vapor infiltration process. The B-C coatings were found to provide advantageous interfacial properties over carbon and BN coatings in several different composite systems. The effectiveness of these different coatings to act as a chemically inert barrier layer and their relationship to the degree of interfacial debonding on the mechanical properties of the composites were examined. The effects of thermal stability and strength of the coated fibers and composites were also determined for several difference atmospheres. In addition, a new method for determining the tensile strength of the as-received and coated yarns was also developed. The coated fibers and composites were further characterized by AES, SEM, XPS, IR and X-ray diffraction analysis.

Effect of Mesoscale and Multiscale Modeling on the Performance of Kevlar Woven Fabric Subjected to Ballistic Impact: A Numerical Study

Science.gov (United States)

Jia, Xin; Huang, Zhengxiang; Zu, Xudong; Gu, Xiaohui; Xiao, Qiangqiang

2013-12-01

In this study, an optimal finite element model of Kevlar woven fabric that is more computational efficient compared with existing models was developed to simulate ballistic impact onto fabric. Kevlar woven fabric was modeled to yarn level architecture by using the hybrid elements analysis (HEA), which uses solid elements in modeling the yarns at the impact region and uses shell elements in modeling the yarns away from the impact region. Three HEA configurations were constructed, in which the solid element region was set as about one, two, and three times that of the projectile's diameter with impact velocities of 30 m/s (non-perforation case) and 200 m/s (perforation case) to determine the optimal ratio between the solid element region and the shell element region. To further reduce computational time and to maintain the necessary accuracy, three multiscale models were presented also. These multiscale models combine the local region with the yarn level architecture by using the HEA approach and the global region with homogenous level architecture. The effect of the varying ratios of the local and global area on the ballistic performance of fabric was discussed. The deformation and damage mechanisms of fabric were analyzed and compared among numerical models. Simulation results indicate that the multiscale model based on HEA accurately reproduces the baseline results and obviously decreases computational time.

Design of an Electronic Chest-Band

Science.gov (United States)

Atakan, R.; Acikgoz Tufan, H.; Baskan, H.; Eryuruk, S. H.; Akalin, N.; Kose, H.; Li, Y.; Kursun Bahadir, S.; Kalaoglu, F.

2017-10-01

In this study, an electronic chest strap prototype was designed for measuring fitness level, performance optimization, mobility and fall detection. Knitting technology is used for production by using highly elastic nylon yarn. In order to evaluate comfort performance of the garment, yarn strength and elongation, air permeability, moisture management and FAST tests (Fabric Assurance Fabric Testing) were carried out, respectively. After testing of textile part of the chest band, IMU sensors were integrated onto the garment by means of conductive yarns. Electrical conductivity of the circuit was also assessed at the end. Results indicated that the weight and the thickness of the product are relatively high for sports uses and it has a negative impact on comfort properties. However, it is highly stretchable and moisture management properties are still in acceptable values. From the perspective of possible application areas, developed smart chest band in this research could be used in sports facilities as well as health care applications for elderly and disabled people.

Knitting and weaving artificial muscles.

Science.gov (United States)

Maziz, Ali; Concas, Alessandro; Khaldi, Alexandre; Stålhand, Jonas; Persson, Nils-Krister; Jager, Edwin W H

2017-01-01

A need exists for artificial muscles that are silent, soft, and compliant, with performance characteristics similar to those of skeletal muscle, enabling natural interaction of assistive devices with humans. By combining one of humankind's oldest technologies, textile processing, with electroactive polymers, we demonstrate here the feasibility of wearable, soft artificial muscles made by weaving and knitting, with tunable force and strain. These textile actuators were produced from cellulose yarns assembled into fabrics and coated with conducting polymers using a metal-free deposition. To increase the output force, we assembled yarns in parallel by weaving. The force scaled linearly with the number of yarns in the woven fabric. To amplify the strain, we knitted a stretchable fabric, exhibiting a 53-fold increase in strain. In addition, the textile construction added mechanical stability to the actuators. Textile processing permits scalable and rational production of wearable artificial muscles, and enables novel ways to design assistive devices.

A Grey Fuzzy Logic Approach for Cotton Fibre Selection

Science.gov (United States)

Chakraborty, Shankar; Das, Partha Protim; Kumar, Vidyapati

2017-06-01

It is a well known fact that the quality of ring spun yarn predominantly depends on various physical properties of cotton fibre. Any variation in these fibre properties may affect the strength and unevenness of the final yarn. Thus, so as to achieve the desired yarn quality and characteristics, it becomes imperative for the spinning industry personnel to identify the most suitable cotton fibre from a set of feasible alternatives in presence of several conflicting properties/attributes. This cotton fibre selection process can be modelled as a Multi-Criteria Decision Making (MCDM) problem. In this paper, a grey fuzzy logic-based approach is proposed for selection of the most apposite cotton fibre from 17 alternatives evaluated based on six important fibre properties. It is observed that the preference order of the top-ranked cotton fibres derived using the grey fuzzy logic approach closely matches with that attained by the past researchers which proves the application potentiality of this method in solving varying MCDM problems in textile industries.

Systematic investigation of drip stains on apparel fabrics: The effects of prior-laundering, fibre content and fabric structure on final stain appearance.

Science.gov (United States)

de Castro, Therese C; Taylor, Michael C; Kieser, Jules A; Carr, Debra J; Duncan, W

2015-05-01

cotton fabrics wicking was accompanied by movement of blood into the fibres/yarns. This study highlights the importance for forensic analysts of apparel evidence to consider the age, the fibre type and the fabric structure before interpreting bloodstain patterns. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Cellulosic Fibers: Effect of Processing on Fiber Bundle Strength

DEFF Research Database (Denmark)

Thygesen, Anders; Madsen, Bo; Thomsen, Anne Belinda

2011-01-01

A range of differently processed cellulosic fibers from flax and hemp plants were investigated to study the relation between processing of cellulosic fibers and fiber bundle strength. The studied processing methods are applied for yarn production and include retting, scutching, carding, and cotto......A range of differently processed cellulosic fibers from flax and hemp plants were investigated to study the relation between processing of cellulosic fibers and fiber bundle strength. The studied processing methods are applied for yarn production and include retting, scutching, carding...

CUSTOMER PERCEIVED QUALITY IMPROVEMENT OF SYNTHETIC FIBER USING FUZZY QFD: A CASE STUDY

OpenAIRE

Golam Kabir; M. Ahsan Akhtar Hasin

2011-01-01

The performance of the ready-made garment (RMG) industry has been one of the most notable success stories of the Bangladesh economy over two decades. To meet the growing demand of synthetic yarns, Bangladesh has to import it from foreign countries which cost a substantial amount of foreign currency for the country. It is a pressing need for local manufacturers to come forward, produce quality synthetic yarn and fulfill the demand of the local market. The purpose of this paper is to present a ...

ESD - FUNCTIONAL CLOTHING

Directory of Open Access Journals (Sweden)

SCARLAT Razvan

2016-05-01

Full Text Available The functional clothing represents a sustainable development direction of in the field of technical textiles, a bridge between various activity domains, a solution to user’s complex requirements. The research and development potential in the field is supported by the new fibers/ yarns generation, the new technologies and the market niches, as well. Protective clothing is now a major part of textile classified under technical textile. Protective clothing refers to the garment and other fabric related items designed to protect the wearer from harsh environmental effects that results in injuries or death. The innovation, as a result of convergence processing technologies, consumer demands and what is viable on the market, defines the personal protective equipment field. In this article, we present the work of an ESD protective clothing development. Therefore, it has been applied a modern knitting technology, on 7E and 12E STOLL machines, using cotton and wool yarns as base yarn and conductive yarns for plaiting structures. Also, the optimal parameters establishment and the functional requirements are aspects of the research activity performed. The experimental models have been conducted in order to demonstrate the design concept used and choosing the optimal variant. The characterization of the developed experimental variants took into account the evaluation of physico-mechanical and electrical characteristics. From the electrical point of view, the variants have been mainly evaluated through “point to point” method in terms of electrical isolation efficiency dimensional changes analysis.

Functional Circuitry on Commercial Fabric via Textile-Compatible Nanoscale Film Coating Process for Fibertronics.

Science.gov (United States)

Bae, Hagyoul; Jang, Byung Chul; Park, Hongkeun; Jung, Soo-Ho; Lee, Hye Moon; Park, Jun-Young; Jeon, Seung-Bae; Son, Gyeongho; Tcho, Il-Woong; Yu, Kyoungsik; Im, Sung Gap; Choi, Sung-Yool; Choi, Yang-Kyu

2017-10-11

Fabric-based electronic textiles (e-textiles) are the fundamental components of wearable electronic systems, which can provide convenient hand-free access to computer and electronics applications. However, e-textile technologies presently face significant technical challenges. These challenges include difficulties of fabrication due to the delicate nature of the materials, and limited operating time, a consequence of the conventional normally on computing architecture, with volatile power-hungry electronic components, and modest battery storage. Here, we report a novel poly(ethylene glycol dimethacrylate) (pEGDMA)-textile memristive nonvolatile logic-in-memory circuit, enabling normally off computing, that can overcome those challenges. To form the metal electrode and resistive switching layer, strands of cotton yarn were coated with aluminum (Al) using a solution dip coating method, and the pEGDMA was conformally applied using an initiated chemical vapor deposition process. The intersection of two Al/pEGDMA coated yarns becomes a unit memristor in the lattice structure. The pEGDMA-Textile Memristor (ETM), a form of crossbar array, was interwoven using a grid of Al/pEGDMA coated yarns and untreated yarns. The former were employed in the active memristor and the latter suppressed cell-to-cell disturbance. We experimentally demonstrated for the first time that the basic Boolean functions, including a half adder as well as NOT, NOR, OR, AND, and NAND logic gates, are successfully implemented with the ETM crossbar array on a fabric substrate. This research may represent a breakthrough development for practical wearable and smart fibertronics.

A Study of Thermistor Performance within a Textile Structure

Directory of Open Access Journals (Sweden)

Theodore Hughes-Riley

2017-08-01

Full Text Available Textiles provide an ideal structure for embedding sensors for medical devices. Skin temperature measurement is one area in which a sensor textile could be particularly beneficial; pathological skin is normally very sensitive, making the comfort of anything placed on that skin paramount. Skin temperature is an important parameter to measure for a number of medical applications, including for the early detection of diabetic foot ulcer formation. To this end an electronic temperature-sensor yarn was developed by embedding a commercially available thermistor chip into the fibres of a yarn, which can be used to produce a textile or a garment. As part of this process a resin was used to encapsulate the thermistor. This protects the thermistor from mechanical and chemical stresses, and also allows the sensing yarn to be washed. Building off preliminary work, the behaviour and performance of an encapsulated thermistor has been characterised to determine the effect of encapsulation on the step response time and absolute temperature measurements. Over the temperature range of interest only a minimal effect was observed, with step response times varying between 0.01–0.35 s. A general solution is presented for the heat transfer coefficient compared to size of the micro-pod formed by the encapsulation of the thermistor. Finally, a prototype temperature-sensing sock was produced using a network of sensing yarns as a demonstrator of a system that could warn of impending ulcer formation in diabetic patients.

Tensile properties of cotton yarn as affected by different yarn singeing machine variables

International Nuclear Information System (INIS)

Tausief, M.Q.; Mahmood, N.; Iqbal, W.

2014-01-01

The present study endeavours to optimise the yam quality in respect of its tensile properties by choosing the best combination of the yam singeing machine variables for excellent manufacture results. This research study revealed that different values of winding speed, gas pressure and air pressure of yam singeing machine put significant effect upon the tensile properties of cotton yam after singeing. (author)

Cellulose/inorganic-composite fibers for producing textile fabrics of high X-ray absorption properties

Energy Technology Data Exchange (ETDEWEB)

Günther, Karoline; Giebing, Christina; Askani, Antonia [FTB, Hochschule Niederrhein – University of Applied Science, Faculty of Textile and Clothing Technology, Webschulstr. 31, 41065 Mönchengladbach (Germany); Leisegang, Tilmann [Saxray GmbH, Maria-Reiche-Str. 1, 01109 Dresden (Germany); Krieg, Marcus [TITK, Thüringisches Institut für Textil- und Kunststoff-Forschung e.V., Breitscheidstraße 97, 07407 Rudolstadt (Germany); Kyosev, Yordan; Weide, Thomas [FTB, Hochschule Niederrhein – University of Applied Science, Faculty of Textile and Clothing Technology, Webschulstr. 31, 41065 Mönchengladbach (Germany); Mahltig, Boris, E-mail: Boris.Mahltig@hs-niederrhein.de [FTB, Hochschule Niederrhein – University of Applied Science, Faculty of Textile and Clothing Technology, Webschulstr. 31, 41065 Mönchengladbach (Germany)

2015-11-01

Common textile materials as cotton or polyester do not possess reliable X-ray absorption properties. This is due to their morphology and chemical composition in particular. Common fibers are built up from organic polymers containing mainly the elements carbon, hydrogen, oxygen and nitrogen. These “light” elements only have low X-ray absorption coefficients. In contrast, inorganic materials composed of “heavy” elements with high atomic numbers, e.g. barium or bismuth, exhibit X-ray absorption coefficients higher by up to two orders of magnitude. To obtain a flexible yarn with high X-ray absorption properties both these materials, the organic polymer and the inorganic X-ray absorber, are combined to an inorganic/organic composite fiber material. Hence, as the organic component cellulose from modified Lyocell-process is used as carrier fiber and blended with inorganic absorber particles of low toxicity and high absorption coefficients, as bariumsulphate, bariumtitanate or bismuthoxide. A content of inorganic absorber particles equally distributed in the whole fiber of up to 20% is achieved. The composite fibers are produced as staple or filament fibers and processed to multifilament or staple fiber yarns. The staple fiber yarns are rotor-spinned to increase the comfort of the subsequent textile material. Several woven fabrics, considering multilayer structure and different warp/weft density, are developed. The energy dependent X-ray shielding properties are determined in dependence on the different yarn compositions, yarn types and structural parameters of the woven fabrics. As a result, a production process of textile materials with comfortable and dedicated X-ray absorption properties is established. It offers a promising opportunity for manufacturing of specialized textiles, working clothes or uniforms applicable for medicine, air craft and security personal, mining as well as for innovative composite materials. - Highlights: • Preparation of cellulosic

Cellulose/inorganic-composite fibers for producing textile fabrics of high X-ray absorption properties

International Nuclear Information System (INIS)

Günther, Karoline; Giebing, Christina; Askani, Antonia; Leisegang, Tilmann; Krieg, Marcus; Kyosev, Yordan; Weide, Thomas; Mahltig, Boris

2015-01-01

Common textile materials as cotton or polyester do not possess reliable X-ray absorption properties. This is due to their morphology and chemical composition in particular. Common fibers are built up from organic polymers containing mainly the elements carbon, hydrogen, oxygen and nitrogen. These “light” elements only have low X-ray absorption coefficients. In contrast, inorganic materials composed of “heavy” elements with high atomic numbers, e.g. barium or bismuth, exhibit X-ray absorption coefficients higher by up to two orders of magnitude. To obtain a flexible yarn with high X-ray absorption properties both these materials, the organic polymer and the inorganic X-ray absorber, are combined to an inorganic/organic composite fiber material. Hence, as the organic component cellulose from modified Lyocell-process is used as carrier fiber and blended with inorganic absorber particles of low toxicity and high absorption coefficients, as bariumsulphate, bariumtitanate or bismuthoxide. A content of inorganic absorber particles equally distributed in the whole fiber of up to 20% is achieved. The composite fibers are produced as staple or filament fibers and processed to multifilament or staple fiber yarns. The staple fiber yarns are rotor-spinned to increase the comfort of the subsequent textile material. Several woven fabrics, considering multilayer structure and different warp/weft density, are developed. The energy dependent X-ray shielding properties are determined in dependence on the different yarn compositions, yarn types and structural parameters of the woven fabrics. As a result, a production process of textile materials with comfortable and dedicated X-ray absorption properties is established. It offers a promising opportunity for manufacturing of specialized textiles, working clothes or uniforms applicable for medicine, air craft and security personal, mining as well as for innovative composite materials. - Highlights: • Preparation of cellulosic

CUSTOMER PERCEIVED QUALITY IMPROVEMENT OF SYNTHETIC FIBER USING FUZZY QFD: A CASE STUDY

Directory of Open Access Journals (Sweden)

Golam Kabir

2011-06-01

Full Text Available The performance of the ready-made garment (RMG industry has been one of the most notable success stories of the Bangladesh economy over two decades. To meet the growing demand of synthetic yarns, Bangladesh has to import it from foreign countries which cost a substantial amount of foreign currency for the country. It is a pressing need for local manufacturers to come forward, produce quality synthetic yarn and fulfill the demand of the local market. The purpose of this paper is to present a Fuzzy Quality Function Deployment (FQFD model to indentify customer requirements and also demonstrate how these requirements can be used to prioritize the design requirements for manufacturing of synthetic yarns. In this system, Fuzzy set theory is integrated into house of quality (HOQ to overcome the shortcomings of the traditional QFD and to capture the inherent impreciseness and vagueness of customer requirements and facilitate to prioritize QFD information. Improving high priority design requirements will ultimately increase customer satisfaction and as a result customer perceived quality will soar.

An Investigation of the Design Potential of Thermochromic Home Textiles Used with Electric Heating Techniques

Directory of Open Access Journals (Sweden)

Hung-Jen Chen

2015-01-01

Full Text Available Thermochromic colorants have been developed since before the 1900s. There are a large number of patents in different applications of thermochromic textiles, but many innovations leave the field of aesthetic and functional textile design unexplored in the area of smart materials. This study aims to develop thermochromic home textiles that change colors and patterns by integrating thermochromic pigments and electric conductive yarns into textile structures. Stainless steel conductive yarns were sewed on textile substrates to enable heat generation to increase fabric temperature. The heat generation and temperature rise could be controlled by monitoring the voltage applied. The experiments of this study focused on analyzing electric resistance and heating properties of the conductive yarns and observing color changing time and color changing effects of the thermochromic textiles. By using the technique in this research, an image of “tai chi” was designed and implemented in a backlighting thermochromic fabric. It illustrates a range of opportunities for thermochromic textiles in new design research directions of Chinese calligraphy and traditional Chinese painting.

Flat knitting of a light emitting textile with optical fibres

DEFF Research Database (Denmark)

Heimdal, Elisabeth Jacobsen

2009-01-01

Knitted products have a flexibility that offers many attractive possibilities. Combined with technical fibres, this gives interesting and innovative possibilities. Many technical fibres and yarns has however properties such as high stiffness and brittleness which are difficult to process in the p......Knitted products have a flexibility that offers many attractive possibilities. Combined with technical fibres, this gives interesting and innovative possibilities. Many technical fibres and yarns has however properties such as high stiffness and brittleness which are difficult to process...... in the practice of weft knitting. This paper is about the experimental product development of a light radiating textile lamp in which optical fibres are used as the only illumination source. The lampshade is produced on an electronic flat knitting machine with special equipment suitable for the feeding of yarn...... with high stiffness. The work was divided in two parts: exploring the possibilities to knit the desired shape on one hand and experimenting about knitting with optical fibres as a weft insertion on the other hand. The method is an inductive approach; a literature survey, information from suppliers...

Textile Resource Conservation Final Report CRADA No. TC-0699-93

Energy Technology Data Exchange (ETDEWEB)

Cooper, John [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); McCreight, Dan J. [Institute of Textile Technology, Charlottesville, VA (United States)

2018-01-22

This project was undertaken to develop and demonstrate on a pilot scale the use of electro-osmotic transport to increase the efficiency of textiles wet processing operations. In particular, we sought to develop a means of rinsing textiles to remove material entrapped between the individual fibers that constitute a yarn. Material trapped within the yarn is slow to exchange with rinse water flowing primarily in the open weave are abetween the yarns. The application of an external field (strength, 5-50 kV /m) requires only a few volts for most fabric thicknesses. This field is sufficient to promote a rapid exchange of material to enhance rinsing and reduce the water required for rinsing from about 20 kg/kg-fabric to 3-6 kg/kg-fabric. We successfully developed technical and economic models of application of the process to the rinsing of many materials of industrial importance, including dyes, tints, chemicals, detergents and dye electrolytes. We demonstrated the process on a pilot plant scale using a translator designed in cooperation with Milliken and Company (Spartanburg, SC).

Injury Prevention Survey: Army Awareness Assessment and Needs Analysis, 9 July - 26 August 2014

Science.gov (United States)

2015-04-01

slip/trip/falls or push/pulling, motor vehicles, parachuting, snow sports, and racquet, or team sports such as football, basketball, and softball ...Extreme conditioning (CrossFit, P90X, etc.)  Football  Racquet sports (raquetball, tennis)  Basketball  Softball / baseball...14.7 Parachuting 93 1 13.7 Football 80 11.7 Softball /baseball 59 8.6 Other 59 -4 8.0 Racquet sports (racquetball, tennis) 54 7.9 Note

Fabrication of continuous electrospun filaments with potential for use as medical fibres.

Science.gov (United States)

Mouthuy, Pierre-Alexis; Zargar, Nasim; Hakimi, Osnat; Lostis, Emilie; Carr, Andrew

2015-05-19

Soft tissue injuries represent a substantial and growing social and economic burden. Medical fibres are commonly used to repair these injuries during surgery. Patient's outcomes are, however, not promising with around 40% of surgical repairs failing within the first few months after surgery due to poor tissue regeneration. The application of nanofibrous filaments and yarns as medical fibres and scaffolds has been suggested to improve soft tissue regeneration and enhance the quality of the repair. However, due to a lack of robustness and reliability of the current fabrication methods, continuous nanofibrous filaments cannot be manufactured and scaled up in industrial settings and are not currently available for clinical use. We have developed a robust and automated method that enables the manufacture of continuous electrospun filaments and which has the potential to be integrated into existing textile production lines. The technology uses a wire guide to form submicrofibres in a dense, narrow mesh which can be detached as a long and continuous thread. The thread can then be stretched and used to create multifilament yarns which can imitate the hierarchical architecture of tissues such as tendons and ligaments. Electrospun polydioxanone yarns produced by this method showed improved cellular proliferation and adhesion when compared to medical monofilament fibres in current clinical use. In vivo, the electrospun yarns showed a good safety profile with mild foreign body reaction and complete degradation within 5 months after implantation. These results suggest that this filament collection method has the potential to become a useful platform for the fabrication of future medical textiles.

THE INFLUENCE OF RAW MATERIAL ON THE LIQUID MOISTURE TRANSPORT THROUGH KNITTED FABRIC

Directory of Open Access Journals (Sweden)

COLDEA Alina

2014-05-01

Full Text Available The comfort is undoubtedly the most important human attribute depends upon the moisture transport which in turn depends on the moisture transport behavior of the knitted fabric. Moisture transport is the transfer of liquid water capillary interstices of the yarns and depends on the wettability of fiber surfaces, as well as the structure of the yarn and fabric. Because of its good water absorption property, cotton is often used for next-to-skin wear such as t-shirts, underwear, socks. All these are known as ``moisture management`` which means the ability of a textile fabric to transport moisture away from the skin to the garment’s outer surface in multi-dimensions and it is one of the key performance criteria in today’s apparel industry since it has a significant effect on the human perception of moisture sensations. In order to study, plated knitted fabric for socks were knitted as plated single jersey in the same production conditions, from different types of yarns, produced in different yarn counts (Ne 20, Ne 24, Ne 30 and different raw material. (cotton, bamboo, soybean, polyester, viscose. Were chose two different density on circular knitting machine. The liquid moisture management of the samples was measured in order to determinate moisture transport index. Was study also the influence of raw material and fabric structure related to the moisture transport index. According to the obtained results, it was found that some of the knitted fabrics used in this study have goodmoisture management capability.

CITA Working for and with material performance

DEFF Research Database (Denmark)

Ramsgaard Thomsen, Mette

2011-01-01

The understanding of materials as active, whether compressed, under tension or flexed while handled, is at the root of all craft traditions. The ability to work a material, to saw and chisel wood, to weld and hammer steel or to weave and knit yarn relies on a profound understanding of its...... performance. The soft flex of wood, the sprung stiffness of steel and the tensile elasticity of yarn are inherent properties that inform and shape our crafts traditions. It is through material understanding that we come to shape the world of artefacts and structure that surrounds us....

Flow Studies of Decelerators at Supersonic Speeds

Science.gov (United States)

1959-01-01

Wind tunnel tests recorded the effect of decelerators on flow at various supersonic speeds. Rigid parachute models were tested for the effects of porosity, shroud length, and number of shrouds. Flexible model parachutes were tested for effects of porosity and conical-shaped canopy. Ribbon dive brakes on a missile-shaped body were tested for effect of tension cable type and ribbon flare type. The final test involved a plastic sphere on riser lines.

Military Free Fall Scheduling And Manifest Optimization Model

Science.gov (United States)

2016-12-01

zone. As interest in qualifying more personnel increased, the course expanded. By the mid-1990s, Reyes explains, a new location was required to better...Since 2005, the Chilean Professional Soccer Association has used operations research techniques to schedule professional leagues in Chile . These...a new parachute the students are using, the RA-1. The RA-1 parachute has a longer glide ratio, which means the rate of descent is slower than with

The Aura of the Analogue in a Digital Age: Women’s Crafts, Creative Markets and Home-Based Labour After Etsy

Directory of Open Access Journals (Sweden)

Susan Luckman

2013-02-01

Full Text Available This article examines the renewed popularity of the handmade by examining the current renaissance in the street credibility of previously disparaged women's craft practices, particularly those employing yarn (for example knitting, crochet, needlepoint and weaving and fabric (sewing, felting. The author historically locates current debates around craft production and creative work by drawing upon the British Arts and Crafts movement, with its own longstanding association with women's' labour in the home and desire to realise sustainable ethical labour practices. Notably, both the periods under discussion mark profound shifts in the economic organisation of society – then, the Industrial Revolution; now the de-industrialisation of much of the 'industrialised' world and the rise of the (digitised knowledge economy – and see a concurrent increase in the popularity of the handmade original as a desirable aesthetic object.

Utilizing Crochet to Showcase Temporal Patterns in Temperature Records from One Location and to Spark a Climate Conversation

Science.gov (United States)

Guertin, L. A.

2017-12-01

Scientists that seek to show temperature changes over time will typically select a line graph as the tool for data communication. However, one non-traditional way to showcase variations in data can be through an artistic visualization created with yarn. For several years, amateur and professional artisans have been using needlework (crocheting/knitting) to represent weather/climate records in scarves and blankets, sharing their work in online communities. Since the Sky Scarf project in 2011, a temporal record of data represented in yarn can include precipitation/snowfall to the air quality index. Here is an example of how crochet is being utilized to show maximum air temperature records over time for one location. Maximum daily temperature values have been collected for January through April in Philadelphia in fifty-year intervals (1917, 1967, 2017). This four-month interval was selected to match with the location and timing of a university's spring semester, as the target audience for this particular visualization is undergraduate students. Instead of trying to read differences in temperature across line graphs plotted for each year, three mini-temperature tapestries have been crocheted. A temperature scale has been developed with rainbow colors of yarn, where the purple and blue represent the coldest temperatures, and the orange and red represent the warmest temperatures. By using the same yarn temperature scale across the three mini-tapestries, the increase in daily maximum temperature in Philadelphia for a set time period can quickly and easily be observed. This form of science art, when presented to students, generates a series of questions, stories and predictions of a scientific and personal nature that are not typically part of a climate science instructional unit.

Removing nickel from nickel-coated carbon fibers

Science.gov (United States)

Hardianto, A.; Hertleer, C.; De Mey, G.; Van Langenhove, L.

2017-10-01

Conductive fibers/yarns are one of the most important materials for smart textiles because of their electrically conductive functionality combined with flexibility and light weight. They can be applied in many fields such as the medical sector, electronics, sensors and even as thermoelectric generators. Temperature sensors, for example, can be made using the thermocouple or thermopile principle which usually uses two different metal wires that can produce a temperature-dependent voltage. However, if metal wires are inserted into a textile structure, they will decrease the flexibility properties of the textile product. Nickel-coated Carbon Fiber (NiCF), a conductive textile yarn, has a potential use as a textile-based thermopile if we can create an alternating region of carbon and nickel along the fiber which in turn it can be used for substituting the metallic thermopile. The idea was to remove nickel from NiCF in order to obtain a yarn that contains alternating zones of carbon and nickel. Due to no literature reporting on how to remove nickel from NiCF, in this paper we investigated some chemicals to remove nickel from NiCF.

A biomimic thermal fabric with high moisture permeability

Directory of Open Access Journals (Sweden)

Fan Jie

2013-01-01

Full Text Available Moisture comfort is an essential factor for functional property of thermal cloth, especially for thick thermal cloth, since thick cloth may hinder effective moisture permeation, and high moisture concentration in the micro-climate between skin and fabric would cause cold feeling. Here, we report a biomimic thermal fabric with excellent warm retention and moisture management properties. In this fabric, the warp yarn system constructs many tree-shaped channel nets in the thickness direction of the fabric. Experimental result indicates that the special hierarchic configuration of warp yarns endows the biomimic thermal fabric with a better warm retention and water vapor management properties compared with the traditional fabrics.

A REVIEW ON TEXTILES IN SPACE PROTECTION EQUIPMENTS

Directory of Open Access Journals (Sweden)

SUNTER EROGLU Nilsen

2017-05-01

Full Text Available Astronauts need the lander for decelerate and bridle the speed when they land on the space surface slowly. This lander could be controlled velocity magnitude in any direction or orientation and provide protection. The landers consist of airbags and parachutes. The airbag is a type of vehicle safety device, have a soft cushioning and is an occupant restraint system. The parachute provides to slow the motion of an object through an atmosphere by the hauling. Space protection equipments must have some properties because of astronaut’s entry, descend and landing in safely. Textiles in airbags provide these properties especially which are light weight, low gas permeability, high strength, low cost, low temperature flexibility and low coefficient of friction. For textiles in parachutes must have properties such as smooth, porosity, air permeability, high strength, cost-effective, stability light weight and good in drag and lift. Airbags and parachutes in space protection equipment’s are improved in systems provide easy stability. Recently, inflatable technologies for space protection equipments plays a fundamental role in building re-entry capsule. It can be performed a variety of pre-flight analyses to ensure the success of the tests of protection systems from day to day. In this review, space protection systems, their textile materials and properties, their advantages and disadvantages are presented.

Dyed Yarns And Dolphin Skins

DEFF Research Database (Denmark)

Gudme, Anne Katrine de Hemmer

2014-01-01

In the Hebrew Bible, there are a remarkable number of texts dealing with temple building, temple furnishing and temple ritual. One would think that with the staggering amount of detailed descriptions offered in these texts a reconstruction of Hebrew Bible temples and ritual should be fairly strai...... a solution to these questions by comparing Hebrew Bible temple texts with other ANE temple texts and by reading the Hebrew Bible temple texts through the lens of cultural memory studies....

Potensi Limbah Padat sebagai Benang Gintir Berbasis Sistem Interlacing

Directory of Open Access Journals (Sweden)

Nisa Fardani

2015-09-01

Full Text Available Sistem pengelolaan sampah di tempat pembuangan sampah menjadi masalah lingkungan yang besar seiring dengan pertumbuhan industri pulp dan kertas di Indonesia. Konversi limbah padat menjadi bahan bakar pelengkap untuk industri kertas juga tidak memberikan hasil yang signifikan untuk memecahkan masalah pencemaran udara pada saat karbon aktif dibebaskan dari proses pembakaran. Masalah ini secara khusus menuntut sistem pengelolaan sampah yang maju dan efektif secara terus-menerus. Baru-baru ini, optimasi pemanfaatan serat-limbah menjadi alternatif khusus untuk mengurangi tumpukan sampah di tempat pembuangan sampah. Namun, tidak semua dapat didaur ulang. Karakteristik limbah padat berserat dari industri kertas tisu cenderung menurun gramaturnya, sehingga sangat disayangkan pemanfaatannya akan berkurang bahkan setelah proses daur ulang. Di sisi lain, struktur kimianya yang telah rusak selama proses produksi tampaknya menjadi semangat baru bagi industri tekstil di masa depan dalam mengembangkan teknologi daur ulang limbah padat berserat, yang menghasilkan benang tekstil generasi baru. Fokus dalam penelitian ini ditekankan pada penemuan tas yang terbuat dari bahan serat-limbah menggunakan metode eksperimental. Identifikasi karakteristik serat-sampah berbasis padat dikembangkan melalui teknik eksplorasi multi-ply yarns berdasarkan sistem interlace. Hubungan antara penciptaan produk dan forecasting  tren pada tahun 2013 akan menjadi analisis berikutnya sebagai salah satu cara untuk memecahkan masalah sampah.Kata Kunci: limbah; multi-ply yarns; sistem interlacing.The Potential of Solid Waste as Multiply Yarn Based on Interlacing SystemsSolid-waste disposal in landfills is becoming a massive environmental problem as a result of the growth of the pulp and paper industry in Indonesia. The conversion of solid waste to complementary fuel for the paper industry is also not giving any significant results to solve air contamination, as active carbon is released

A prototype yarn evaluation tester to rapidly assess comparative weavability of warp yarns without weaving

Science.gov (United States)

The art of weaving continues to be the most predominantly used method of converting textile fibers into fabrics for various end-use applications, including apparel. In fact, the weaving is by far the largest textile manufacturing sector, worldwide. However, the weaving process is complex and costly....

Parachute Recovery Systems Design Manual

Science.gov (United States)

1991-03-01

Decelerators Operating at High Altitudes and High Mach Numbers, by W E. Nikel and W M. Gran. USAF, July 1964. (USAF Report FDL-TDR-64-35.) 5-139 NWC TP...CUTTER BLADE ’S ACTUATOR ASSEMBLY ASSEMBL WELDED CLOSURE DISK LINE BORON/CALCIUM CHROMATE 1OHM BRIDGE -. (47gm Dia. Wire Tophet C) DAP RING POLVIMIDE...thread used in woven metals such as metal shielding for electrical wiring . All other man-made fibers are based on cellulose, protein, or resin composites

Is Wine a Financial Parachute?

OpenAIRE

Baldi, Lucia; Vandone, Daniela; Peri, Massimo

2010-01-01

This paper analyzes the relationship between Global Wine Industry Share Price Indexes and composite stock market indexes using a Threshold Vector Error Correction Model (TVECM), aiming to investigate if investments in the wine sector play a role in determining financial risk and return to investors who include it in their portfolio. Whilst in most of the literature analyses the return of investments of fine wine, this paper places the focus to “normal” (i.e. non‐fine) wine, using data from th...

MISSION PROFILE AND DESIGN CHALLENGES FOR MARS LANDING EXPLORATION

Directory of Open Access Journals (Sweden)

J. Dong

2017-07-01

Full Text Available An orbiter and a descent module will be delivered to Mars in the Chinese first Mars exploration mission. The descent module is composed of a landing platform and a rover. The module will be released into the atmosphere by the orbiter and make a controlled landing on Martian surface. After landing, the rover will egress from the platform to start its science mission. The rover payloads mainly include the subsurface radar, terrain camera, multispectral camera, magnetometer, anemometer to achieve the scientific investigation of the terrain, soil characteristics, material composition, magnetic field, atmosphere, etc. The landing process is divided into three phases (entry phase, parachute descent phase and powered descent phase, which are full of risks. There exit lots of indefinite parameters and design constrain to affect the selection of the landing sites and phase switch (mortaring the parachute, separating the heat shield and cutting off the parachute. A number of new technologies (disk-gap-band parachute, guidance and navigation, etc. need to be developed. Mars and Earth have gravity and atmosphere conditions that are significantly different from one another. Meaningful environmental conditions cannot be recreated terrestrially on earth. A full-scale flight validation on earth is difficult. Therefore the end-to-end simulation and some critical subsystem test must be considered instead. The challenges above and the corresponding design solutions are introduced in this paper, which can provide reference for the Mars exploration mission.

Free-Spinning Characteristics of a 1/24-Scale Model of the Grumman F11F-1 Airplane, TED No. NACA AD 395

Science.gov (United States)

Bowman, James S., Jr.

1955-01-01

An investigation is being conducted in the Langley 20-foot free-spinning tunnel on a 1/24-scale model of the Grumman F11F-1 airplane to determine spin and recovery characteristics and the minimum-size parachute required to satisfactorily terminate the spin in an emergency. Results obtained to date are presented herein. Test results indicate that it may be difficult to obtain an erect or inverted spin on the airplane, but, if a spin is obtained, the spin will be very oscillatory and recovery from the developed erect spin by rudder reversal may not be possible. The lateral controls will have no appreciable effect on recoveries from erect.spins. Recovery from the inverted spin by merely neutralizing the rudder will be satisfactory. After recoveries by rudder reversal and after recoveries from spins without control movement (no spins), the model oftentimes rolled very rapidly about the X-axis. Based on limited preliminary tests made in this investigation to make the model recover satisfactorily, it appears that canards near the nose of the airplane or differentially operated horizontal tails may be utilized to provide rapid recoveries. The parachute test results indicate that an 11-foot-diameter (laid-out-flat) parachute with a drag coefficient of 0.650 (based on the laid- out-flat diameter) and with a towline length equal to the wing span is the minimum-size parachute required to satisfactorily terminate an erect or inverted spin in an emergency.

Porosity Prediction of Plain Weft Knitted Fabrics

Directory of Open Access Journals (Sweden)

Muhammad Owais Raza Siddiqui

2014-12-01

Full Text Available Wearing comfort of clothing is dependent on air permeability, moisture absorbency and wicking properties of fabric, which are related to the porosity of fabric. In this work, a plug-in is developed using Python script and incorporated in Abaqus/CAE for the prediction of porosity of plain weft knitted fabrics. The Plug-in is able to automatically generate 3D solid and multifilament weft knitted fabric models and accurately determine the porosity of fabrics in two steps. In this work, plain weft knitted fabrics made of monofilament, multifilament and spun yarn made of staple fibers were used to evaluate the effectiveness of the developed plug-in. In the case of staple fiber yarn, intra yarn porosity was considered in the calculation of porosity. The first step is to develop a 3D geometrical model of plain weft knitted fabric and the second step is to calculate the porosity of the fabric by using the geometrical parameter of 3D weft knitted fabric model generated in step one. The predicted porosity of plain weft knitted fabric is extracted in the second step and is displayed in the message area. The predicted results obtained from the plug-in have been compared with the experimental results obtained from previously developed models; they agreed well.

Statistical shear lag model - unraveling the size effect in hierarchical composites.

Science.gov (United States)

Wei, Xiaoding; Filleter, Tobin; Espinosa, Horacio D

2015-05-01

Numerous experimental and computational studies have established that the hierarchical structures encountered in natural materials, such as the brick-and-mortar structure observed in sea shells, are essential for achieving defect tolerance. Due to this hierarchy, the mechanical properties of natural materials have a different size dependence compared to that of typical engineered materials. This study aimed to explore size effects on the strength of bio-inspired staggered hierarchical composites and to define the influence of the geometry of constituents in their outstanding defect tolerance capability. A statistical shear lag model is derived by extending the classical shear lag model to account for the statistics of the constituents' strength. A general solution emerges from rigorous mathematical derivations, unifying the various empirical formulations for the fundamental link length used in previous statistical models. The model shows that the staggered arrangement of constituents grants composites a unique size effect on mechanical strength in contrast to homogenous continuous materials. The model is applied to hierarchical yarns consisting of double-walled carbon nanotube bundles to assess its predictive capabilities for novel synthetic materials. Interestingly, the model predicts that yarn gauge length does not significantly influence the yarn strength, in close agreement with experimental observations. Copyright © 2015 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Tubular lining material for pipelines having bends

Energy Technology Data Exchange (ETDEWEB)

Moringa, A.; Sakaguchi, Y.; Hyodo, M.; Yagi, I.

1987-03-24

A tubular lining material for pipelines having bends or curved portions comprises a tubular textile jacket made of warps and wefts woven in a tubular form overlaid with a coating of a flexible synthetic resin. It is applicable onto the inner surface of a pipeline having bends or curved portions in such manner that the tubular lining material with a binder onto the inner surface thereof is inserted into the pipeline and allowed to advance within the pipeline, with or without the aid of a leading rope-like elongated element, while turning the tubular lining material inside out under fluid pressure. In this manner the tubular lining material is applied onto the inner surface of the pipeline with the binder being interposed between the pipeline and the tubular lining material. The lining material is characterized in that a part of all of the warps are comprised of an elastic yarn around which, over the full length thereof, a synthetic fiber yarn or yarns have been left-and/or right-handedly coiled. This tubular lining material is particularly suitable for lining a pipeline having an inner diameter of 25-200 mm and a plurality of bends, such as gas service pipelines or house pipelines, without occurrence of wrinkles in the lining material in a bend.

Novel fiber-based pure chitosan scaffold for tendon augmentation: biomechanical and cell biological evaluation.

Science.gov (United States)

Nowotny, J; Aibibu, D; Farack, J; Nimtschke, U; Hild, M; Gelinsky, M; Kasten, P; Cherif, Ch

2016-07-01

One possibility to improve the mechanical properties after tendon ruptures is augmentation with a scaffold. Based on wet spinning technology, chitosan fibres were processed to a novel pure high-grade multifilament yarn with reproducible quality. The fibres were braided to obtain a 3D tendon scaffold. The CS fibres and scaffolds were evaluated biomechanically and compared to human supraspinatus (SSP) tendons. For the cytobiological characterization, in vitro cell culture experiments with human mesenchymal stem cells (hMSC) were performed. Three types of 3D circular braided scaffolds were fabricated. Significantly, higher ultimate stress values were measured for scaffold with larger filament yarn, compared to scaffold with smaller filament yarn. During cultivation over 28 days, the cells showed in dependence of isolation method and/or donor a doubling or tripling of the cell number or even a six-fold increase on the CS scaffold, which was comparable to the control (polystyrene) or in the case of cells obtained from human biceps tendon even higher proliferation rates. After 14 days, the scaffold surface was covered homogeneously with a cell layer. In summary, the present work demonstrates that braided chitosan scaffolds constitute a straightforward approach for designing tendon analogues, maintaining important flexibility in scaffold design and providing favourable mechanical properties of the resulting construct.

An ethnographic action research study to investigate the experiences of Bindjareb women participating in the cooking and nutrition component of an Aboriginal health promotion programme in regional Western Australia.

Science.gov (United States)

Nilson, Caroline; Kearing-Salmon, Karrie-Anne; Morrison, Paul; Fetherston, Catherine

2015-12-01

To investigate the experiences of women participating in a cooking and nutrition component of a health promotion research initiative in an Australian Aboriginal regional community. Weekly facilitated cooking and nutrition classes were conducted during school terms over 12 months. An ethnographic action research study was conducted for the programme duration with data gathered by participant and direct observation, four yarning groups and six individual yarning sessions. The aim was to determine the ways the cooking and nutrition component facilitated lifestyle change, enabled engagement, encouraged community ownership and influenced community action. Regional Bindjareb community in the Nyungar nation of Western Australia. A sample of seventeen Aboriginal women aged between 18 and 60 years from the two kinships in two towns in one shire took part in the study. The recruitment and consent process was managed by community Elders and leaders. Major themes emerged highlighting the development of participants and their recognition of the need for change: the impact of history on current nutritional health of Indigenous Australians; acknowledging shame; challenges of change around nutrition and healthy eating; the undermining effect of mistrust and limited resources; the importance of community control when developing health promotion programmes; finding life purpose through learning; and the need for planning and partnerships to achieve community determination. Suggested principles for developing cooking and nutrition interventions are: consideration of community needs; understanding the impact of historical factors on health; understanding family and community tensions; and the engagement of long-term partnerships to develop community determination.

The Haitian Economy and the HOPE Act

National Research Council Canada - National Science Library

Hornbeck, J. F

2008-01-01

...., non-regional yarns, fabrics, and components) provided Haiti met rules of origin and eligibility criteria that require making progress on worker rights, poverty reduction, and anti-corruption measures...

78 FR 25565 - Controlled Import Permits

Science.gov (United States)

2013-05-02

... replacing the term ``Deputy Administrator'' with ``Administrator'' and making minor editorial changes. New..., linters, and other forms of cotton fiber (not including yarn, thread, and cloth); cottonseed hulls, cake...

HELIUM-POWERED BALLISTIC TEST APPARATUS

Data.gov (United States)

Federal Laboratory Consortium — This research device is used for the initial assessment of new materials and is primarily used for fragmentation testing of yarns, fabric, or laminate samples. The...

Mars Exploration Rover Terminal Descent Mission Modeling and Simulation

Science.gov (United States)

Raiszadeh, Behzad; Queen, Eric M.

2004-01-01

Because of NASA's added reliance on simulation for successful interplanetary missions, the MER mission has developed a detailed EDL trajectory modeling and simulation. This paper summarizes how the MER EDL sequence of events are modeled, verification of the methods used, and the inputs. This simulation is built upon a multibody parachute trajectory simulation tool that has been developed in POST I1 that accurately simulates the trajectory of multiple vehicles in flight with interacting forces. In this model the parachute and the suspended bodies are treated as 6 Degree-of-Freedom (6 DOF) bodies. The terminal descent phase of the mission consists of several Entry, Descent, Landing (EDL) events, such as parachute deployment, heatshield separation, deployment of the lander from the backshell, deployment of the airbags, RAD firings, TIRS firings, etc. For an accurate, reliable simulation these events need to be modeled seamlessly and robustly so that the simulations will remain numerically stable during Monte-Carlo simulations. This paper also summarizes how the events have been modeled, the numerical issues, and modeling challenges.

Chemical-vapor-infiltrated silicon nitride, boron nitride, and silicon carbide matrix composites

International Nuclear Information System (INIS)

Ventri, R.D.; Galasso, F.S.

1990-01-01

This paper reports composites of carbon/chemical-vapor-deposited (CVD) Si 3 N 4 , carbon/CVD BN, mullite/CVD SiC, and SiC yarn/CVD SiC prepared to determine if there were inherent toughness in these systems. The matrices were deposited at high enough temperatures to ensure that they were crystalline, which should make them more stable at high temperatures. The fiber-matrix bonding in the C/Si 3 N 4 composite appeared to be too strong; the layers of BN in the matrix of the C/BN were too weakly bonded; and the mullite/SiC composite was not as tough as the SiC/SiC composites. Only the SiC yarn/CVD SiC composite exhibited both strength and toughness

A torsional artificial muscle from twisted nitinol microwire

Science.gov (United States)

Mirvakili, Seyed M.; Hunter, Ian W.

2017-04-01

Nitinol microwires of 25 μm in diameter can have tensile actuation of up to 4.5% in less than 100 ms. A work density of up to 480 MPa can be achieved from these microwires. In the present work, we are showing that by twisting the microwires in form of closed-loop two-ply yarn we can create a torsional actuator. We achieved a revisable torsional stroke of 46°/mm with peak rotational speed of up to 10,000 rpm. We measured a gravimetric torque of up to 28.5 N•m/kg which is higher than the 3 - 6 N•m/kg for direct-drive commercial electric motors. These remarkable performance results are comparable to those of guest-infiltrated carbon nanotube twisted yarns.

Solid-state, polymer-based fiber solar cells with carbon nanotube electrodes.

Science.gov (United States)

Liu, Dianyi; Zhao, Mingyan; Li, Yan; Bian, Zuqiang; Zhang, Luhui; Shang, Yuanyuan; Xia, Xinyuan; Zhang, Sen; Yun, Daqin; Liu, Zhiwei; Cao, Anyuan; Huang, Chunhui

2012-12-21

Most previous fiber-shaped solar cells were based on photoelectrochemical systems involving liquid electrolytes, which had issues such as device encapsulation and stability. Here, we deposited classical semiconducting polymer-based bulk heterojunction layers onto stainless steel wires to form primary electrodes and adopted carbon nanotube thin films or densified yarns to replace conventional metal counter electrodes. The polymer-based fiber cells with nanotube film or yarn electrodes showed power conversion efficiencies in the range 1.4% to 2.3%, with stable performance upon rotation and large-angle bending and during long-time storage without further encapsulation. Our fiber solar cells consisting of a polymeric active layer sandwiched between steel and carbon electrodes have potential in the manufacturing of low-cost, liquid-free, and flexible fiber-based photovoltaics.

A Unit-Cell Model for Predicting the Elastic Constants of 3D Four Directional Cylindrical Braided Composite Shafts

Science.gov (United States)

Hao, Wenfeng; Liu, Ye; Huang, Xinrong; Liu, Yinghua; Zhu, Jianguo

2018-06-01

In this work, the elastic constants of 3D four directional cylindrical braided composite shafts were predicted using analytical and numerical methods. First, the motion rule of yarn carrier of 3D four directional cylindrical braided composite shafts was analyzed, and the horizontal projection of yarn motion trajectory was obtained. Then, the geometry models of unit-cells with different braiding angles and fiber volume contents were built up, and the meso-scale models of 3D cylindrical braided composite shafts were obtained. Finally, the effects of braiding angles and fiber volume contents on the elastic constants of 3D braided composite shafts were analyzed theoretically and numerically. These results play a crucial role in investigating the mechanical properties of 3D 4-directional braided composites shafts.

AgeFactDB—the JenAge Ageing Factor Database—towards data integration in ageing research

Science.gov (United States)

Hühne, Rolf; Thalheim, Torsten; Sühnel, Jürgen

2014-01-01

AgeFactDB (http://agefactdb.jenage.de) is a database aimed at the collection and integration of ageing phenotype data including lifespan information. Ageing factors are considered to be genes, chemical compounds or other factors such as dietary restriction, whose action results in a changed lifespan or another ageing phenotype. Any information related to the effects of ageing factors is called an observation and is presented on observation pages. To provide concise access to the complete information for a particular ageing factor, corresponding observations are also summarized on ageing factor pages. In a first step, ageing-related data were primarily taken from existing databases such as the Ageing Gene Database—GenAge, the Lifespan Observations Database and the Dietary Restriction Gene Database—GenDR. In addition, we have started to include new ageing-related information. Based on homology data taken from the HomoloGene Database, AgeFactDB also provides observation and ageing factor pages of genes that are homologous to known ageing-related genes. These homologues are considered as candidate or putative ageing-related genes. AgeFactDB offers a variety of search and browse options, and also allows the download of ageing factor or observation lists in TSV, CSV and XML formats. PMID:24217911

New concept of age(ing: Prospective age

Directory of Open Access Journals (Sweden)

Devedžić Mirjana

2012-01-01

Full Text Available While the last century was the century of world population growth, according to demographers, the XXI century will be century of population aging. Statistics undoubtedly show that number of elderly will continue it’s growth in the future. If old age is seen as period of life with reduced physical and mental capabilities and increased disability, and demographic aging as increase of dependent population, trends are quite disturbing, at least in certain societal segments. In developed countries, this population category is no longer treated as passive or as a "burden of society" and efforts are made for better social inclusion of older people. In contrast to growing interest in this phenomenon, the concepts that define the aging of the population remained stagnant. The aim of this paper is to introduce into domestic literature the term "prospective age" as a dynamic category which is more affected with socio-historical conditions, not only with biological as traditional definition of aging suggested. Papers written by Sanderson and Scherbov offer new methodological options for study of population aging, because it takes into account the biometric rather than chronological approach. Calculation of prospective years is a simple operation that requires pair of the same number of remained life expectancy from life tables for two different periods (the year of concern is index, and the one we are comparing with is standard year, so that phrase "40s is the new 30s" or "70s the new 60s" gets scientific foundation. Average remaining years of life represent a realistic indicator suggesting increased capacity, activity and vitality of individuals, which is due to accepted demographic parameters still considered old. „Prospective threshold“ is defined as the age when life expectancy falls below 15 years (it is subjective choice made by Sanderson and Scherbov, which is also used in this paper and during the elaboration of these ideas three demographic

Transportation Career Field, AFSC 60XXX

Science.gov (United States)

1988-04-01

equipment, affixirg parachutes and extraction systems to airdrop loads, * rigging cargo on platforms for airdrops, assembling extraction systems and attaching...C Z= C4 (D Il L-. Ill CD Ill l "- 1i CD P-4J (i 0D CL .J wIX I- In V -i W I L 0e W Z-I -I 7-1 . C-) 1W ID .. C> LL w C) 10 C- = CDCt l 1) 0 < W...PERCENT MEMBERS PERFORMING PERCENT , MEMBERS ’ TASKS PERFORMING M1129 AFFIX PARACHUTES TO AIRDROP LOADS 99 M1149 RIG CARGO ON PLATFORMS FOR AIRDROPS 96

New Textile Sensors for In Situ Structural Health Monitoring of Textile Reinforced Thermoplastic Composites Based on the Conductive Poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) Polymer Complex.

Science.gov (United States)

Jerkovic, Ivona; Koncar, Vladan; Grancaric, Ana Marija

2017-10-10

Many metallic structural and non-structural parts used in the transportation industry can be replaced by textile-reinforced composites. Composites made from a polymeric matrix and fibrous reinforcement have been increasingly studied during the last decade. On the other hand, the fast development of smart textile structures seems to be a very promising solution for in situ structural health monitoring of composite parts. In order to optimize composites' quality and their lifetime all the production steps have to be monitored in real time. Textile sensors embedded in the composite reinforcement and having the same mechanical properties as the yarns used to make the reinforcement exhibit actuating and sensing capabilities. This paper presents a new generation of textile fibrous sensors based on the conductive polymer complex poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) developed by an original roll to roll coating method. Conductive coating for yarn treatment was defined according to the preliminary study of percolation threshold of this polymer complex. The percolation threshold determination was based on conductive dry films' electrical properties analysis, in order to develop highly sensitive sensors. A novel laboratory equipment was designed and produced for yarn coating to ensure effective and equally distributed coating of electroconductive polymer without distortion of textile properties. The electromechanical properties of the textile fibrous sensors confirmed their suitability for in situ structural damages detection of textile reinforced thermoplastic composites in real time.

IMPROVING KNITTED FABRICS BY A STATISTICAL CONTROL OF DIMENSIONAL CHANGES AFTER THE DYEING PROCESS

Directory of Open Access Journals (Sweden)

LLINARES-BERENGUER Jorge

2017-05-01

Full Text Available One of the most important problems that cotton knitted fabrics present during the manufacturing process is their dimensional instability, which needs to be minimised. Some of the variables that intervene in fabric shrinkage are related with its structural characteristics, use of fiber when producing yarn, the yarn count used or the dyeing process employed. Conducted under real factory conditions, the present study attempted to model the behaviour of a fabric structure after a dyeing process by contributing several algorithms that calculate dyed fabric stability after the first wash cycle. Small-diameter circular machines are used to produce garments with no side seams. This is the reason why a list of machines that produce the same fabrics for different widths needs to be made available to produce all the sizes of a given garment. Two relaxation states were distingued for interlock fabric: dyed and dry relaxation, and dyed and wash relaxation. The linear density of the yarn employed to produce sample fabric was combed cotton Ne 30. The machines used for optic bleaching were Overflow. To obtain knitting structures with optimum dimensional stability, different statistical tools were used to help us to evaluate all the production process variables (raw material, machines and process responsible for this variation. This allowed to guarantee product quality without creating costs and losses.

3D Orthogonal Woven Triboelectric Nanogenerator for Effective Biomechanical Energy Harvesting and as Self-Powered Active Motion Sensors.

Science.gov (United States)

Dong, Kai; Deng, Jianan; Zi, Yunlong; Wang, Yi-Cheng; Xu, Cheng; Zou, Haiyang; Ding, Wenbo; Dai, Yejing; Gu, Bohong; Sun, Baozhong; Wang, Zhong Lin

2017-10-01

The development of wearable and large-area energy-harvesting textiles has received intensive attention due to their promising applications in next-generation wearable functional electronics. However, the limited power outputs of conventional textiles have largely hindered their development. Here, in combination with the stainless steel/polyester fiber blended yarn, the polydimethylsiloxane-coated energy-harvesting yarn, and nonconductive binding yarn, a high-power-output textile triboelectric nanogenerator (TENG) with 3D orthogonal woven structure is developed for effective biomechanical energy harvesting and active motion signal tracking. Based on the advanced 3D structural design, the maximum peak power density of 3D textile can reach 263.36 mW m -2 under the tapping frequency of 3 Hz, which is several times more than that of conventional 2D textile TENGs. Besides, its collected power is capable of lighting up a warning indicator, sustainably charging a commercial capacitor, and powering a smart watch. The 3D textile TENG can also be used as a self-powered active motion sensor to constantly monitor the movement signals of human body. Furthermore, a smart dancing blanket is designed to simultaneously convert biomechanical energy and perceive body movement. This work provides a new direction for multifunctional self-powered textiles with potential applications in wearable electronics, home security, and personalized healthcare. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Investigation of Wear Behaviour of Sewn Assemblies of Viscose Linings with Different Treatment

Directory of Open Access Journals (Sweden)

Dainora BAČKAUSKAITĖ

2011-07-01

Full Text Available Different types of chemical treatment of textile are widely applied in advanced textile. Finishing of textile can provide additional functional properties for products or/and to improve the appearance of final product as well as to improve their mechanical properties. In this research the influence of the industrial treatment of viscose linings on the parameters of fabric surface friction, on fabric surface appearance as well as on the slippage resistance of yarns at a seam was investigated. Raw, dyed, dyed and softened, dyed and non-slip finished plain weaved linings were investigated. The slippage resistance of yarns at a seam in woven fabrics was evaluated according to standard EN ISO 13936-1:2004. The friction was investigated according to the standard DIN 53375 in a fabric-fabric friction pair. Surface of raw, dyed, dyed and softened viscose lining was investigated using SEM. The obtained results have shown that the friction parameters as well as the parameters of seam slippage resistance of dyed or dyed and softened fabrics were higher than the ones of raw fabric. The highest differences in those parameters were obtained for lining that was dyed and treated with non-slip finishing. That type of finishing influenced the break of lining yarns without typical to the other investigated linings slipping near a stitching line.http://dx.doi.org/10.5755/j01.ms.17.2.485

An Alternative Flight Software Trigger Paradigm: Applying Multivariate Logistic Regression to Sense Trigger Conditions Using Inaccurate or Scarce Information

Science.gov (United States)

Smith, Kelly M.; Gay, Robert S.; Stachowiak, Susan J.

2013-01-01

In late 2014, NASA will fly the Orion capsule on a Delta IV-Heavy rocket for the Exploration Flight Test-1 (EFT-1) mission. For EFT-1, the Orion capsule will be flying with a new GPS receiver and new navigation software. Given the experimental nature of the flight, the flight software must be robust to the loss of GPS measurements. Once the high-speed entry is complete, the drogue parachutes must be deployed within the proper conditions to stabilize the vehicle prior to deploying the main parachutes. When GPS is available in nominal operations, the vehicle will deploy the drogue parachutes based on an altitude trigger. However, when GPS is unavailable, the navigated altitude errors become excessively large, driving the need for a backup barometric altimeter to improve altitude knowledge. In order to increase overall robustness, the vehicle also has an alternate method of triggering the parachute deployment sequence based on planet-relative velocity if both the GPS and the barometric altimeter fail. However, this backup trigger results in large altitude errors relative to the targeted altitude. Motivated by this challenge, this paper demonstrates how logistic regression may be employed to semi-automatically generate robust triggers based on statistical analysis. Logistic regression is used as a ground processor pre-flight to develop a statistical classifier. The classifier would then be implemented in flight software and executed in real-time. This technique offers improved performance even in the face of highly inaccurate measurements. Although the logistic regression-based trigger approach will not be implemented within EFT-1 flight software, the methodology can be carried forward for future missions and vehicles.

An Alternative Flight Software Paradigm: Applying Multivariate Logistic Regression to Sense Trigger Conditions using Inaccurate or Scarce Information

Science.gov (United States)

Smith, Kelly; Gay, Robert; Stachowiak, Susan

2013-01-01

In late 2014, NASA will fly the Orion capsule on a Delta IV-Heavy rocket for the Exploration Flight Test-1 (EFT-1) mission. For EFT-1, the Orion capsule will be flying with a new GPS receiver and new navigation software. Given the experimental nature of the flight, the flight software must be robust to the loss of GPS measurements. Once the high-speed entry is complete, the drogue parachutes must be deployed within the proper conditions to stabilize the vehicle prior to deploying the main parachutes. When GPS is available in nominal operations, the vehicle will deploy the drogue parachutes based on an altitude trigger. However, when GPS is unavailable, the navigated altitude errors become excessively large, driving the need for a backup barometric altimeter to improve altitude knowledge. In order to increase overall robustness, the vehicle also has an alternate method of triggering the parachute deployment sequence based on planet-relative velocity if both the GPS and the barometric altimeter fail. However, this backup trigger results in large altitude errors relative to the targeted altitude. Motivated by this challenge, this paper demonstrates how logistic regression may be employed to semi-automatically generate robust triggers based on statistical analysis. Logistic regression is used as a ground processor pre-flight to develop a statistical classifier. The classifier would then be implemented in flight software and executed in real-time. This technique offers improved performance even in the face of highly inaccurate measurements. Although the logistic regression-based trigger approach will not be implemented within EFT-1 flight software, the methodology can be carried forward for future missions and vehicles

Critical Spacecraft-to-Earth Communications for Mars Exploration Rover (MER) entry, descent and landing

Science.gov (United States)

Hurd, William J.; Estabrook, Polly; Racho, Caroline S.; Satorius, Edgar H.

2002-01-01

For planetary lander missions, the most challenging phase of the spacecraft to ground communications is during the entry, descent, and landing (EDL). As each 2003 Mars Exploration Rover (MER) enters the Martian atmosphere, it slows dramatically. The extreme acceleration and jerk cause extreme Doppler dynamics on the X-band signal received on Earth. When the vehicle slows sufficiently, the parachute is deployed, causing almost a step in deceleration. After parachute deployment, the lander is lowered beneath the parachute on a bridle. The swinging motion of the lander imparts high Doppler dynamics on the signal and causes the received signal strength to vary widely, due to changing antenna pointing angles. All this time, the vehicle transmits important health and status information that is especially critical if the landing is not successful. Even using the largest Deep Space Network antennas, the weak signal and high dynamics render it impossible to conduct reliable phase coherent communications. Therefore, a specialized form of frequency-shift-keying will be used. This paper describes the EDL scenario, the signal conditions, the methods used to detect and frequency-track the carrier and to detect the data modulation, and the resulting performance estimates.

Rupture of the pectoralis major muscle in a paratrooper.

Science.gov (United States)

Komurcu, Mahmut; Yildiz, Yavuz; Ozdemir, M Taner; Erler, Kaan

2004-01-01

Rupture of the pectoralis major muscle is a very rare injury. Excessive contraction of muscle fibers during certain forms of sports, such as weightlifting and bench pressing, is the most common cause. Among the 150 reported cases in the literature, in only 1 case did the injury happen during the landing phase of parachuting. Here we report a case of pectoralis major muscle rupture caused by a different mechanism than published previously. A paratrooper was injured during a tactical jump out of an aircraft after becoming entangled with the risers. The mechanism of injury was excessive traction and malpositioning of his shoulder when the parachute deployed. A three-phase conservative treatment regimen was performed and results were assessed by dynamometry. The patient was satisfied with the treatment and the dynamometric results were good at 9 mo after injury and at the end of a 20-mo follow-up period. We suggest that three-phase rehabilitation can be an effective treatment option for pectoralis major muscle rupture in selected patients. Prevention of this type of altitude injury would be possible by applying the fundamentals of parachuting.

Doctor's Diary and Memoirs. Pond's Party, F Force, Thai-Burma ...

African Journals Online (AJOL)

feeling. Descriptions of getting together with friends and co-PWs to have 'a few yarns' under the ... ensures the safe and controlled distribution of ... Throughout the book the most important ethical aspect of ... consequent degree of disability.

New Textile Sensors for In Situ Structural Health Monitoring of Textile Reinforced Thermoplastic Composites Based on the Conductive Poly(3,4-ethylenedioxythiophene-poly(styrenesulfonate Polymer Complex

Directory of Open Access Journals (Sweden)

Ivona Jerkovic

2017-10-01

Full Text Available Many metallic structural and non-structural parts used in the transportation industry can be replaced by textile-reinforced composites. Composites made from a polymeric matrix and fibrous reinforcement have been increasingly studied during the last decade. On the other hand, the fast development of smart textile structures seems to be a very promising solution for in situ structural health monitoring of composite parts. In order to optimize composites’ quality and their lifetime all the production steps have to be monitored in real time. Textile sensors embedded in the composite reinforcement and having the same mechanical properties as the yarns used to make the reinforcement exhibit actuating and sensing capabilities. This paper presents a new generation of textile fibrous sensors based on the conductive polymer complex poly(3,4-ethylenedioxythiophene-poly(styrenesulfonate developed by an original roll to roll coating method. Conductive coating for yarn treatment was defined according to the preliminary study of percolation threshold of this polymer complex. The percolation threshold determination was based on conductive dry films’ electrical properties analysis, in order to develop highly sensitive sensors. A novel laboratory equipment was designed and produced for yarn coating to ensure effective and equally distributed coating of electroconductive polymer without distortion of textile properties. The electromechanical properties of the textile fibrous sensors confirmed their suitability for in situ structural damages detection of textile reinforced thermoplastic composites in real time.

Investigation of Mechanical and Electromagnetic Interference Shielding Properties of Nickel-CFRP Textile Composites

Science.gov (United States)

Tugirumubano, Alexandre; Vijay, Santhiyagu Joseph; Go, Sun Ho; Kwac, Lee Ku; Kim, Hong Gun

2018-04-01

The most common materials used for electromagnetic interference shielding are metals and their alloys. However, those materials are heavy and highly reflective. In order to eliminate or reduce the intensity of wave radiation in their working environment, lightweight materials that have interference shielding properties are needed. In this paper, nickel wire mesh yarns (warps) were woven into carbon fibers-reinforced plastic yarns (wefts) to produce metal-carbon textile composite materials. The plain weave and 2/2 twill weave techniques were used, and the woven fabrics were laminated to manufacture experimental test samples. The nickel, which has high magnetic permeability and good electric conductivity, and carbon fibers, which have good electrical, thermal and mechanical properties, were used together to achieve the desired properties. The shielding effectiveness of each sample was investigated using a network analyzer connected with coaxial transmission line test in accordance with ASTM 4935-99 standard, with the frequencies ranging from 500 MHz to 1.5 GHz. Here, the plain weave structure showed higher shielding effectiveness than twill weave. The absorption losses for both materials were relatively greater than reflection losses. In reference to the orientation of wire mesh yarns about the loading axis, the tensile strengths in the transversal direction were 19.04 and 16.34% higher than the tensile strengths in longitudinal direction for plain weave and twill weave, respectively. The fractography analysis with SEM showed a ductile fracture of wire mesh and brittle fracture of epoxy matrix and carbon fibers.

MATHEMATICAL MODELLING OF THE SHIELDING EFFECTIVENESS FOR PES/STAINLESS STEEL FABRICS

Directory of Open Access Journals (Sweden)

RADULESCU Ion Razvan

2017-05-01

Full Text Available Textile screens for electromagnetic radiation represent a modern solution, due to their flexibility, lightweight and good mechanical resistance. Electromagnetic shielding is a must in various applications, while strict regulations are set for electromagnetic compatibility. Conductive fabrics are widely used for electronic equipment covers, RF suits or EMI protection tents. This paper aims to investigate the shielding effectiveness of conductive woven fabrics with stainless steel yarns at different weft distances [2,3,4,5 mm]. These conductive fabrics were investigated for their physical-mechanical properties (mass per surface unit, density on warp and weft direction and thickness, within the INCDTP accredited laboratories. The conductive fabrics as well as combinations thereof where tested for their shielding effectiveness accordingly to the standard ASTM ES 07, within the EMC laboratories of ICPE-CA. A signal generator, an amplifier, a TEM Cell and a spectrum analyser were used were used for this purpose. Graphs in logarithmic scale were issued for the shielding effectiveness analysis. Moreover, an experimental factorial plan was conceived for obtaining a mathematical model for the studied fabrics in relation to the weft distance between the conductive yarns. The coefficients of the mathematical model were obtained through the least squares regression method in Excel, while the response curve was designed in Matlab. The response curve enables the computation of intermediate values of the shielding effectiveness in relation to the distance between conductive yarns.

Development of glass fibre reinforced composites using microwave heating technology

Science.gov (United States)

Köhler, T.; Vonberg, K.; Gries, T.; Seide, G.

2017-10-01

Fibre reinforced composites are differentiated by the used matrix material (thermoplastic versus duroplastic matrix) and the level of impregnation. Thermoplastic matrix systems get more important due to their suitability for mass production, their good shapeability and their high impact resistance. A challenge in the processing of these materials is the reduction of the melt flow paths of the thermoplastic matrix. The viscosity of molten thermoplastic material is distinctly higher than the viscosity of duroplastic material. An approach to reduce the flow paths of the thermoplastic melt is given by a commingling process. Composites made from commingling hybrid yarns consist of thermoplastic and reinforcing fibres. Fabrics made from these hybrid yarns are heated and consolidated by the use of heat pressing to form so called organic sheets. An innovative heating system is given by microwaves. The advantage of microwave heating is the volumetric heating of the material, where the energy of the electromagnetic radiation is converted into thermal energy inside the material. In this research project microwave active hybrid yarns are produced and examined at the Institute for Textile Technology of RWTH Aachen University (ITA). The industrial research partner Fricke und Mallah Microwave Technology GmbH, Peine, Germany develops an innovative pressing systems based on a microwave heating system. By implementing the designed microwave heating technology into an existing heat pressing process, FRTCs are being manufactured from glass and nanomodified polypropylene fibre woven fabrics. In this paper the composites are investigated for their mechanical and optical properties.

Investigation of Mechanical and Electromagnetic Interference Shielding Properties of Nickel-CFRP Textile Composites

Science.gov (United States)

Tugirumubano, Alexandre; Vijay, Santhiyagu Joseph; Go, Sun Ho; Kwac, Lee Ku; Kim, Hong Gun

2018-05-01

The most common materials used for electromagnetic interference shielding are metals and their alloys. However, those materials are heavy and highly reflective. In order to eliminate or reduce the intensity of wave radiation in their working environment, lightweight materials that have interference shielding properties are needed. In this paper, nickel wire mesh yarns (warps) were woven into carbon fibers-reinforced plastic yarns (wefts) to produce metal-carbon textile composite materials. The plain weave and 2/2 twill weave techniques were used, and the woven fabrics were laminated to manufacture experimental test samples. The nickel, which has high magnetic permeability and good electric conductivity, and carbon fibers, which have good electrical, thermal and mechanical properties, were used together to achieve the desired properties. The shielding effectiveness of each sample was investigated using a network analyzer connected with coaxial transmission line test in accordance with ASTM 4935-99 standard, with the frequencies ranging from 500 MHz to 1.5 GHz. Here, the plain weave structure showed higher shielding effectiveness than twill weave. The absorption losses for both materials were relatively greater than reflection losses. In reference to the orientation of wire mesh yarns about the loading axis, the tensile strengths in the transversal direction were 19.04 and 16.34% higher than the tensile strengths in longitudinal direction for plain weave and twill weave, respectively. The fractography analysis with SEM showed a ductile fracture of wire mesh and brittle fracture of epoxy matrix and carbon fibers.

Improvement of carbon nanotubes films conductivity for use in biomedical application

Science.gov (United States)

Dybowska-Sarapuk, Łucja; Janczak, Daniel; Krzemiński, Jakub; Lepak, Sandra; Łekawa-Raus, Agnieszka; MłoŻniak, Anna; Jakubowska, Małgorzata

2017-08-01

Carbon nanotube (CNT) yarns and sheets due to their biocompatibility, very good mechanical strength and flexibility can find wide range of applications in nanomedicine, inter alia as mechanical actuators for artificial muscles or electrodes used for deep brain stimulation. However, because of CNT film behavior in liquid environment, before their using in biological applications, they should be coated with a special protective layer. The purpose of created coatings is not only to protect the films, but also to increase their conductivity. The aim of the research was to test various methods of achieving such coatings on CNT films and to evaluate quality and flexibility of coated CNT films. The coatings were made using various suspensions containing polymer materials such methyl polymethacrylate and conductive silver flakes. The methods tested in this study were: dipping, painting and flooding of the CNT yarns.

Dielectric Behaviour of Some Woven Fabrics on the Basis of Natural Cellulosic Fibers

Directory of Open Access Journals (Sweden)

Florin St. C. Mustata

2014-01-01

Full Text Available The electrical permittivity of the weaves obtained from natural cellulosic yarns or mixed with synthetic fibers was established with capacitor method. The highest value of relative electrical permittivity in case of the woven fabric from natural cellulosic fibers has been observed at the weave made of pure hemp (13.55 and the lowest at the weave obtained from the pure jute—weave packing (1.87. Electrical permittivity value of the pure jute weave packing is comparable to that of the permittivity for the glass thread, when the work conditions are as follows: temperature 25°C and air humidity 35%. The relative electrical permittivity of the weave is depending on the degree of crimping yarns especially in the weft direction, technological density in direction of the warp and weft, and surface mass of the weave.

The Effect of Tensile Hysteresis and Contact Resistance on the Performance of Strain-Resistant Elastic-Conductive Webbing

Directory of Open Access Journals (Sweden)

Tien-Wei Shyr

2011-01-01

Full Text Available To use e-textiles as a strain-resistance sensor they need to be both elastic and conductive. Three kinds of elastic-conductive webbings, including flat, tubular, and belt webbings, made of Lycra fiber and carbon coated polyamide fiber, were used in this study. The strain-resistance properties of the webbings were evaluated in stretch-recovery tests and measured within 30% strain. It was found that tensile hysteresis and contact resistance significantly influence the tensile elasticity and the resistance sensitivity of the webbings. The results showed that the webbing structure definitely contributes to the tensile hysteresis and contact resistance. The smaller the friction is among the yarns in the belt webbing, the smaller the tensile hysteresis loss. However the close proximity of the conductive yarns in flat and tubular webbings results in a lower contact resistance.

Experimental Investigations of Woven Textile Tape as Strain Sensor

Science.gov (United States)

Kannaian, T.; Naveen, V. S.; Muthukumar, N.; Thilagavathi, G.

2015-10-01

In this article, a strain sensitive textile based elastomeric tape sensor has been developed and process parameters for sensor development are optimized. Polyester yarns are used as base threads and rubber threads are used as elastomer for the sensor development. The sensor has been developed with the help of narrow width tape loom by introducing the silver coated nylon yarn in the middle of the tape structure. The influence of weave structure, number of conductive threads and rubber thread tension on sensor development has been optimized by using the Box-Behnken method and the results are analyzed using the Design expert software. From the results, it is found that six numbers of conductive threads in a plain weave structure with rubber thread tension of 750 g is suitable for the sensor to give high gauge factor of 1.626.

32 CFR 705.18 - Authority and coordination.

Science.gov (United States)

2010-07-01

...) Public events in the Washington, DC area. (4) Aerial, parachute, or simulated tactical demonstrations.... (6) Programmed national sports, professional athletic events, formal international competitions, and...

Investigation on effect of fibre hybridization and orientation on ...

Indian Academy of Sciences (India)

2017-07-25

Jul 25, 2017 ... for fibres to assess their efficiency. The first ... alternative to flax spun yarns. Bledzki et al ... Natural fibre composite are renewable, light in weight with ..... absorbs more energy due to hybridization of abaca and neem fibres.

Sensation seeking in males involved in recreational high risk sports

Directory of Open Access Journals (Sweden)

M Guszkowska

2010-09-01

Full Text Available The study examined sensation seeking intensity level in males involved in recreational high risk sports and investigated whether its level depends on type of sport practised. Additionally, in case of parachutists, sport experience of study participants were scrutinised with regard to its possible impact on the level of sensation seeking.The research involved 217 males aged 17 to 45, practising recreational high risk sports, namely: parachuting (n=98; wakeboarding (n=30; snowboarding (n=30; scuba diving (n=22; alpinism (n=20; paragliding (n=17. The control group included 54 men not involved in sports. Polish version of Sensation Seeking Scale (SSS-IV of Zuckerman was applied.Results show, that high risk sports males are featured by stronger need of sensations in comparison to control group and this concerned all but one aspect of sensation seeking variable. The only exception was the need of intellectual stimulation. Except from the thrill and adventure seeking dimension, type of sport may also be an important determinant of sensation seeking. Men practising snowboard and wakeboard presented stronger need for sensations, especially in the dimension of experience seeking, disinhibition and boredom susceptibility. Sport experience (number of jumps in parachuting did not differentiate the level of sensation seeking among investigated parachutists. Population of sport high risk male takers was not homogeneous, and therefore in future research one should analyse specific sports (or events in a certain sport separately.

Influence of the emotional state on behavior in extreme conditions of competitive sports activities

Directory of Open Access Journals (Sweden)

V.A. Malakhov

2014-04-01

Full Text Available Purpose : establish a communication pattern of emotional intensity and level of extreme environment in which activity is performed. Materials : in the study involved 600 men aged 18-22 years. Results : the effect of the emotional state on the efficiency of the motor activity that flowed under extreme conditions. Set individual characteristics flow sports activities in extreme conditions. First used in the special semantic space for the orderly presentation of research results parachute jumps. The monogram built in semantic fields allows to establish the frequency response range of individual heartbeats and the optimal frequency for maximum performance. On the basis of established regularities of the "reflex of readiness" assessment methodology given emotional stress, which reflects the readiness of an individual to perform a parachute jump. An objective indicator of preparedness measures is a violation of the symmetry of the flow and haptic reflex and serial dynamometry. Conclusions : in using semantic spaces reflects the flowing of reflex of biological caution and accompaniment reflex. In the basis of constructing estimates of emotional stress are the regularities of mean arterial pressure as nonspecific reactions. Measure of extent of confused is estimated by variability of accompaniment reflex. Breach of symmetry in mean arterial pressure and the amplitude - frequency response accompaniment reflex, determine the validity of staying in extreme conditions. Introduction of the measure in using semantic spaces allows by selective data to establish the overall structure of the studied process.

Influence of the emotional state on behavior in extreme conditions of competitive sports activities

Directory of Open Access Journals (Sweden)

Malakhov V.A.

2014-03-01

Full Text Available Purpose : establish a communication pattern of emotional intensity and level of extreme environment in which activity is performed. Materials : in the study involved 600 men aged 18-22 years. Results : the effect of the emotional state on the efficiency of the motor activity that flowed under extreme conditions. Set individual characteristics flow sports activities in extreme conditions. First used in the special semantic space for the orderly presentation of research results parachute jumps. The monogram built in semantic fields allows to establish the frequency response range of individual heartbeats and the optimal frequency for maximum performance. On the basis of established regularities of the "reflex of readiness" assessment methodology given emotional stress, which reflects the readiness of an individual to perform a parachute jump. An objective indicator of preparedness measures is a violation of the symmetry of the flow and haptic reflex and serial dynamometry. Conclusions : in using semantic spaces reflects the flowing of reflex of biological caution and accompaniment reflex. In the basis of constructing estimates of emotional stress are the regularities of mean arterial pressure as nonspecific reactions. Measure of extent of confused is estimated by variability of accompaniment reflex. Breach of symmetry in mean arterial pressure and the amplitude - frequency response accompaniment reflex, determine the validity of staying in extreme conditions. Introduction of the measure in using semantic spaces allows by selective data to establish the overall structure of the studied process.

The Strong Family Program: an innovative model to engage Aboriginal and Torres Strait Islander youth and Elders with reproductive and sexual health community education.

Science.gov (United States)

Duley, P; Botfield, J R; Ritter, T; Wicks, J; Brassil, A

2017-08-01

Issue addressed Aboriginal youth in Australia often experience high rates of intimate partner violence (family violence) and poorer reproductive and sexual health than their non-Aboriginal counterparts. To address some of the disparities, the Strong Family Program was developed to deliver reproductive and sexual health education to Aboriginal communities in New South Wales. Methods Development of the program was based on an extensive consultation process with Aboriginal communities. It was implemented in three communities, with two groups from each hosting Aboriginal youth and Elders in a yarning circle within the culturally respectful frameworks of 'men and boys'' and 'women and girls'' business. An evaluation was conducted to measure reproductive and sexual health knowledge and attitude changes upon program completion, using pre- and post-program surveys and yarning (focus group discussions). Results Program participants comprised 48 females and 28 males. Overall, mean knowledge and attitude scores improved upon completion of the program (from 77% to 82% and from 4.15 to 4.32 out of 5, respectively). Among participants aged 20 years and under (the youngest participant was 13 years), there was an increase in knowledge (P=0.034); among participants aged over 20 years (the oldest participant was 78 years), there was an increase in positive attitudes (P=0.001). Participants perceived the information provided to be useful and relevant, with many reporting improved knowledge and attitudes around rights and respectful relationships. Conclusions Reproductive and sexual health education in Aboriginal communities should be based on community consultations and carried out within a culturally appropriate framework to promote greater success. Continued implementation of the Strong Family Program will promote increased understanding of respectful relationships and improved health outcomes for Aboriginal young people. So what? The Strong Family Program was based on an extensive

Age Group Differences in Perceived Age Discrimination: Associations With Self-Perceptions of Aging.

Science.gov (United States)

Giasson, Hannah L; Queen, Tara L; Larkina, Marina; Smith, Jacqui

2017-08-01

From midlife onwards, age stereotypes increasingly underlie social judgments and contribute to age-based discrimination. Whereas many studies compare differences between young and older adults in reports of age discrimination or sensitivity to age stereotypes, few consider age group differences among adults over 50. We form subgroups corresponding to social age group membership (early midlife, late midlife, young old, oldest old) and examine differences in reported experiences of everyday age discrimination and associations with self-perceptions of aging. Using cross-sectional and longitudinal data from the Health and Retirement Study (HRS: N = 15,071; M Age = 68, range 50-101), multivariate logistic regression was used to examine experiences of everyday discrimination attributed to age, and associations between age discrimination and self-perceptions of aging, in four age groups: early midlife, late midlife, young old, oldest old. People in the early midlife group (aged 50-59) reported more experiences of unfair treatment than the older age groups but were less likely to attribute their experiences to age discrimination. After controlling for covariates, individuals in all age groups who perceived their own aging positively were less likely to report experiences of age discrimination. The magnitude of this effect, however, was greatest in the early midlife group. Findings support proposals that midlife is a pivotal life period when individuals adjust to life events and social role transitions. Future longitudinal studies will provide further insight into whether positive self-perceptions of aging are especially important in this phase of the life course. © The Author 2017. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Scope of nanotechnology in modern textiles

Science.gov (United States)

This review article demonstrates the scope and applications of nanotechnology towards modification and development of advanced textile fibers, yarns and fabrics and their processing techniques. Basically, it summarizes the recent advances made in nanotechnology and its applications to cotton textil...

Nutrients, Microglia Aging, and Brain Aging

Directory of Open Access Journals (Sweden)

Zhou Wu

2016-01-01

Full Text Available As the life expectancy continues to increase, the cognitive decline associated with Alzheimer’s disease (AD becomes a big major issue in the world. After cellular activation upon systemic inflammation, microglia, the resident immune cells in the brain, start to release proinflammatory mediators to trigger neuroinflammation. We have found that chronic systemic inflammatory challenges induce differential age-dependent microglial responses, which are in line with the impairment of learning and memory, even in middle-aged animals. We thus raise the concept of “microglia aging.” This concept is based on the fact that microglia are the key contributor to the acceleration of cognitive decline, which is the major sign of brain aging. On the other hand, inflammation induces oxidative stress and DNA damage, which leads to the overproduction of reactive oxygen species by the numerous types of cells, including macrophages and microglia. Oxidative stress-damaged cells successively produce larger amounts of inflammatory mediators to promote microglia aging. Nutrients are necessary for maintaining general health, including the health of brain. The intake of antioxidant nutrients reduces both systemic inflammation and neuroinflammation and thus reduces cognitive decline during aging. We herein review our microglia aging concept and discuss systemic inflammation and microglia aging. We propose that a nutritional approach to controlling microglia aging will open a new window for healthy brain aging.

Nutrients, Microglia Aging, and Brain Aging.

Science.gov (United States)

Wu, Zhou; Yu, Janchun; Zhu, Aiqin; Nakanishi, Hiroshi

2016-01-01

As the life expectancy continues to increase, the cognitive decline associated with Alzheimer's disease (AD) becomes a big major issue in the world. After cellular activation upon systemic inflammation, microglia, the resident immune cells in the brain, start to release proinflammatory mediators to trigger neuroinflammation. We have found that chronic systemic inflammatory challenges induce differential age-dependent microglial responses, which are in line with the impairment of learning and memory, even in middle-aged animals. We thus raise the concept of "microglia aging." This concept is based on the fact that microglia are the key contributor to the acceleration of cognitive decline, which is the major sign of brain aging. On the other hand, inflammation induces oxidative stress and DNA damage, which leads to the overproduction of reactive oxygen species by the numerous types of cells, including macrophages and microglia. Oxidative stress-damaged cells successively produce larger amounts of inflammatory mediators to promote microglia aging. Nutrients are necessary for maintaining general health, including the health of brain. The intake of antioxidant nutrients reduces both systemic inflammation and neuroinflammation and thus reduces cognitive decline during aging. We herein review our microglia aging concept and discuss systemic inflammation and microglia aging. We propose that a nutritional approach to controlling microglia aging will open a new window for healthy brain aging.

Design of a Modular Monolithic Implicit Solver for Multi-Physics Applications

Science.gov (United States)

Carton De Wiart, Corentin; Diosady, Laslo T.; Garai, Anirban; Burgess, Nicholas; Blonigan, Patrick; Ekelschot, Dirk; Murman, Scott M.

2018-01-01

The design of a modular multi-physics high-order space-time finite-element framework is presented together with its extension to allow monolithic coupling of different physics. One of the main objectives of the framework is to perform efficient high- fidelity simulations of capsule/parachute systems. This problem requires simulating multiple physics including, but not limited to, the compressible Navier-Stokes equations, the dynamics of a moving body with mesh deformations and adaptation, the linear shell equations, non-re effective boundary conditions and wall modeling. The solver is based on high-order space-time - finite element methods. Continuous, discontinuous and C1-discontinuous Galerkin methods are implemented, allowing one to discretize various physical models. Tangent and adjoint sensitivity analysis are also targeted in order to conduct gradient-based optimization, error estimation, mesh adaptation, and flow control, adding another layer of complexity to the framework. The decisions made to tackle these challenges are presented. The discussion focuses first on the "single-physics" solver and later on its extension to the monolithic coupling of different physics. The implementation of different physics modules, relevant to the capsule/parachute system, are also presented. Finally, examples of coupled computations are presented, paving the way to the simulation of the full capsule/parachute system.

New raw materials improve packing sealing efficiency

International Nuclear Information System (INIS)

Igel, B.; McKeague, L.

2012-01-01

End-users and OEM's using or manufacturing on/off and control valves expect a permanent and effective increase in service life together with an increased sealing capability while at the same time minimizing maintenance concerns. Developing materials which provide consistency and repeatability are essential characteristics to optimizing valve performance. “New Generation” materials and yarn allow us to meet this growing demand while complying with the requirements related to chemical purity and an increased level of safety to both plant workers and equipment in the nuclear environment. Through R&D initiatives and developments in new and improved raw materials; a new mechanical packing generation which optimizes friction coefficients and extended life cycle has been introduced to the industry. Lower friction values drastically optimize actuator effort and size improving efficiency for stem operation with significant improvements in flow control of fluids. Combined with new and improved procedures (installation, torque levels and consolidation recommendations), this new packing generation has provided significant improvement in the mechanical behavior of packing materials (independent tests carried out in collaboration with AECL and CETIM) this has provided the opportunity to develop successful Valve Enhancement Programs which offer improved efficiency, valve operation and repeatability. These NEW generation yarns are available with or without wire reinforcement depending on specific operating parameters and conditions. The purpose of this presentation is to demonstrate that new generation material(s). Which are available to the industry for AOV, MOV and Manual valves? - To highlight the steps taken in R&D and manufacturing contributing to the much improved yarns and finished packing products. - Comply and are designed to meet the stringent requirements in the nuclear industry - Simplify valve maintenance without risk to safety or performance - Increase service

Influence of the vacuum resin process, on the ballistic behaviour of lightweight armouring solutions

Science.gov (United States)

Lefebvre, M.; Boussu, F.; Coutellier, D.; Vallee, D.

2012-08-01

The armour of vehicles against conventional threats is mainly composed with steel or aluminium panels. Efficient heavy solutions exist, but the involved industries require new lightweight structures. Moreover, unconventional threats as IEDs (Improvised Explosive Devices) may cause severe damages on these structural and protective panel solutions. Thus, combination of aluminium or steel plates with textile composite structures used as a backing, leads to the mass reduction and better performance under delamination behaviour against these new threats. This paper is a part of a study dealing with the impact behaviour of three warp interlocks weaving structures under Fragment Simulating Projectile (FSP) impact. During this research, several parameters has being studied as the influence of the yarns insertions [1-4], the degradation of the yarns during the weaving process [5-7], and the influence of the resin rate on the ballistic behaviour. The resin rate inside composite materials is dependant on the final application. In ballistic protection, we need to control the resin rate in order to have a deformable structure in order to absorb the maximum of energy. However, with the warp interlocks weaving structure, the yarns insertions induce empty spaces between the yarns where the resin takes place without being evacuated. The resin rate inside the warp interlocks structures is in the most of cases less than 50%, which lead to have brittle and hard material during the impact. Contrary to interlocks structures, the existing protection based on prepreg structure have a high fibres ratio around 88% of weight. That leads to have the best ballistic properties during the impact and good deformability of the structure. The aim of this paper is to evaluate the influence of the resin rate on the ballistic results of the composites materials. For that, we have chosen two kinds of warp interlocks fabrics which were infused with epoxy resin following two processes. The first is a

Botanical trash mixtures analyzed with near-infrared and attenuated total reflectance fourier transform spectroscopy and thermogravimetric analysis

Science.gov (United States)

Botanical cotton trash mixed with lint reduces cotton’s marketability and appearance. During cotton harvesting, ginning, and processing, trash size reduction occurs, thus complicating its removal and identification. This trash causes problems by increasing ends down in yarn formation and thus proce...

Design, Manufacture and Analysis of Tough, Nanostructure-Reinforced High-Performance Polymers

Science.gov (United States)

2014-07-04

by deprotonating macroscale, commercial Kevlar yarns using potassium hydroxide in dimethyl sulfoxide to yield stable dispersions of nanometer...Exponential Layer-by-Layer Polyurethane/Poly( Acrylic Acid) Films," Engineering Fracture Mechanics, Vol 77, pp 3227-3245, 2010. 10. Sain, T., Meaud, J., Yeom

76 FR 71831 - Defense Federal Acquisition Regulation Supplement: Fire-Resistant Fiber for Production of...

Science.gov (United States)

2011-11-18

..., suppliers, or distributors of fire-resistant fibers, yarns, fabrics, or military uniforms) submitted.... The law does not restrict DoD's selection and use of fabrics containing fire-resistant rayon fiber... from selecting fabrics that include fire- resistant rayon fibers. Response: These responses have...

Advanced Silicone-based Coatings for Flexible Fabric Applications, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Silicone coatings are the system of choice for inflatable fabrics used in several space, military, and consumer applications, including airbags, parachutes, rafts,...

Aerospace Activities in the Elementary School

Science.gov (United States)

Jones, Robert M.; Wiggins, Kenneth E.

1974-01-01

Describes 17 activities which are aerospace oriented and yet provide an interdisciplinary approach to learning. Some of the activities described involve paper airplanes, parachutes, model rockets, etc. (BR)

A Dropsonde UAV for Atmospheric Sensing in a Turbulent Environment, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Dropsondes are one of the primary atmospheric measurement tools available to researchers. Current dropsondes are deployed with a free fall parachute trajectory,...

A Dropsonde Glider with Adaptive Trajectory Planning, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Dropsondes are one of the primary atmospheric measurement tools available to researchers. Current dropsondes are deployed with a free fall parachute trajectory,...

Harvesting electrical energy from torsional thermal actuation driven by natural convection.

Science.gov (United States)

Kim, Shi Hyeong; Sim, Hyeon Jun; Hyeon, Jae Sang; Suh, Dongseok; Spinks, Geoffrey M; Baughman, Ray H; Kim, Seon Jeong

2018-06-07

The development of practical, cost-effective systems for the conversion of low-grade waste heat to electrical energy is an important area of renewable energy research. We here demonstrate a thermal energy harvester that is driven by the small temperature fluctuations provided by natural convection. This harvester uses coiled yarn artificial muscles, comprising well-aligned shape memory polyurethane (SMPU) microfibers, to convert thermal energy to torsional mechanical energy, which is then electromagnetically converted to electrical energy. Temperature fluctuations in a yarn muscle, having a maximum hot-to-cold temperature difference of about 13 °C, were used to spin a magnetic rotor to a peak torsional rotation speed of 3,000 rpm. The electromagnetic energy generator converted the torsional energy to electrical energy, thereby producing an oscillating output voltage of up to 0.81 V and peak power of 4 W/kg, based on SMPU mass.

Electrochemically Powered, Energy-Conserving Carbon Nanotube Artificial Muscles.

Science.gov (United States)

Lee, Jae Ah; Li, Na; Haines, Carter S; Kim, Keon Jung; Lepró, Xavier; Ovalle-Robles, Raquel; Kim, Seon Jeong; Baughman, Ray H

2017-08-01

While artificial muscle yarns and fibers are potentially important for many applications, the combination of large strokes, high gravimetric work capacities, short cycle times, and high efficiencies are not realized for these fibers. This paper demonstrates here electrochemically powered carbon nanotube yarn muscles that provide tensile contraction as high as 16.5%, which is 12.7 times higher than previously obtained. These electrochemical muscles can deliver a contractile energy conversion efficiency of 5.4%, which is 4.1 times higher than reported for any organic-material-based artificial muscle. All-solid-state parallel muscles and braided muscles, which do not require a liquid electrolyte, provide tensile contractions of 11.6% and 5%, respectively. These artificial muscles might eventually be deployed for a host of applications, from robotics to perhaps even implantable medical devices. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

FINAL PROCESS DEPENDENT DIMENSIONAL CHANGES OF DOUBLE KNIT FABRICS

Directory of Open Access Journals (Sweden)

Vedat ÖZYAZGAN

2012-01-01

Full Text Available In this paper Ne 30/1 cotton yarn obtained by using pure cotton fibers is employed. 1x1, 2x1 and 3x1 Rib fabrics were knitted with yarns at different gauges. During the knitting process, the tension was kept constant. In order to investigate the relaxation on the knitting process fabric samples were treated using three relaxation processes; dry, wet and full respectively. After each relaxation process, stitches dimensions were measured. As a result of these measurements, it is observed that as the relaxation increases the stitches length decreases while the stitches width increases. In rib knitting, As the fabric stretches increases the stitch length increases. As a result it is observed that as the stitch length increases, the width of the stitches increases linearly. In all rib fabrics, increase in the stitch density leads to an increase in the weight of the fabric.

Ceramic hot-gas filter

Science.gov (United States)

Connolly, E.S.; Forsythe, G.D.; Domanski, D.M.; Chambers, J.A.; Rajendran, G.P.

1999-05-11

A ceramic hot-gas candle filter is described having a porous support of filament-wound oxide ceramic yarn at least partially surrounded by a porous refractory oxide ceramic matrix, and a membrane layer on at least one surface thereof. The membrane layer may be on the outer surface, the inner surface, or both the outer and inner surface of the porous support. The membrane layer may be formed of an ordered arrangement of circularly wound, continuous filament oxide ceramic yarn, a ceramic filler material which is less permeable than the filament-wound support structure, or some combination of continuous filament and filler material. A particularly effective membrane layer features circularly wound filament with gaps intentionally placed between adjacent windings, and a filler material of ceramic particulates uniformly distributed throughout the gap region. The filter can withstand thermal cycling during back pulse cleaning and is resistant to chemical degradation at high temperatures.

Ceramic hot-gas filter

Science.gov (United States)

Connolly, Elizabeth Sokolinski; Forsythe, George Daniel; Domanski, Daniel Matthew; Chambers, Jeffrey Allen; Rajendran, Govindasamy Paramasivam

1999-01-01

A ceramic hot-gas candle filter having a porous support of filament-wound oxide ceramic yarn at least partially surrounded by a porous refractory oxide ceramic matrix, and a membrane layer on at least one surface thereof. The membrane layer may be on the outer surface, the inner surface, or both the outer and inner surface of the porous support. The membrane layer may be formed of an ordered arrangement of circularly wound, continuous filament oxide ceramic yarn, a ceramic filler material which is less permeable than the filament-wound support structure, or some combination of continuous filament and filler material. A particularly effective membrane layer features circularly wound filament with gaps intentionally placed between adjacent windings, and a filler material of ceramic particulates uniformly distributed throughout the gap region. The filter can withstand thermal cycling during backpulse cleaning and is resistant to chemical degradation at high temperatures.

Low Density Supersonic Decelerators

Data.gov (United States)

National Aeronautics and Space Administration — The Low-Density Supersonic Decelerator project will demonstrate the use of inflatable structures and advanced parachutes that operate at supersonic speeds to more...

Aging in Taiwan: Building a Society for Active Aging and Aging in Place.

Science.gov (United States)

Lin, Yi-Yin; Huang, Chin-Shan

2016-04-01

Taiwan's accelerated rate of aging is more than twice that of European countries and United States. Although demographic aging was not a major concern in Taiwan until 1993, when it became an aging society, aging issues now have become an imperative topic both in policy and in practice in the country. As this article demonstrates, in response to the challenge of the rapidly growing older population and the inspiration of cultural values of filial obligation and respect to elders, the concepts of active aging and aging in place are leading the policies and practices of gerontology to meet the diverse needs of the aging population in Taiwan. However, challenges remain, including the question of how to promote systematic endeavors, both in policies or research on aging, and how to encourage greater involvement of nongovernment organizations in the aging issue. In addition, some emerging issues about aging are addressed in this article including inadequate resources for older rural adults, building an age-friendly environment, and the increasing number of people with dementia. © The Author 2015. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Kenaf Fibre Crop for Bioeconomic Industrial Development

NARCIS (Netherlands)

Lips, S.J.J.; Dam, van J.E.G.

2013-01-01

Kenaf (Hibiscus cannabinus L.) is a high yielding fibre crop that can be utilised as raw material in many industrial applications ranging from traditional fabrics, yarns and ropes to new applications in building materials, composites and lightweight car parts. Kenaf competes in some applications

Mechanical Characterization and Fractography of Glass Fiber/Polyamide (PA6) Composites

DEFF Research Database (Denmark)

Raghavalu Thirumalai, Durai Prabhakaran; Pillai, Saju; Charca, Samuel

2015-01-01

The mechanical properties of the glass fiber reinforced Polyamide (PA6) composites made by prepreg tapes and commingled yarns were studied by in-plane compression, short-beam shear, and flexural tests. The composites were fabricated with different fiber volume contents (prepregs—47%, 55%, 60%, an...

19 CFR 10.844 - Value-content requirement.

Science.gov (United States)

2010-04-01

... preference program. The producer ships to the United States four shipments during the initial applicable one... this subpart. (5) Inclusion of the cost of fabrics or yarns not available in commercial quantities in..., Singapore, Chile, Australia, Morocco, Bahrain, El Salvador, Honduras, Nicaragua, Guatemala, Dominican...

46 CFR 160.028-3 - Materials, workmanship, construction, and performance requirements.

Science.gov (United States)

2010-10-01

... be corrosion-resistant or properly protected against corrosion. The ejection mechanism shall be of... pistol-projected parachute red flare distress signals of the type covered by Subpart 160.024. The...

The technology applying of inflatable devices to access adaptation, movement and landing descent vehicle from Martian environment to the Earth conditions

Science.gov (United States)

Koryanov, Vsevolod V.; Kazakovtsev, Victor P.

2017-07-01

At present, the idea has emerged to use special inflatable braking device (IBD) which permits to implement the landing vehicle (LV) "soft" landing on the planet's surface without a parachute system. Braking device (BD) unfolds still at the extra-atmospheric flight stage to provide the LV passive stabilisation, and the entire apparatus together with the braking device is twisted around its longitudinal axis. The advantage of an inflatable BD over traditional non-rigid brakes - parachutes is that it can be used at the atmospheric stage of the descent, starting from hypersonic speeds, and ending subsonic ones. These main theses are implemented in the project MetNet and its sequel project RITD, using Entry, Descent and Landing System (EDLS) system [1].

Simulation Development and Analysis of Crew Vehicle Ascent Abort

Science.gov (United States)

Wong, Chi S.

2016-01-01

NASA's Commercial Crew Program is an integral step in its journey to Mars as it would expedite development of space technologies and open up partnership with U.S. commercial companies. NASA reviews and independent assessment of Commercial Crew Program is fundamental to its success, and being able to model a commercial crew vehicle in a simulation rather than conduct a live test would be a safer, faster, and less expensive way to assess and certify the capabilities of the vehicle. To this end, my project was to determine the feasibility of using a simulation tool named SOMBAT version 2.0 to model a multiple parachute system for Commercial Crew Program simulation. The main tasks assigned to me were to debug and test the main parachute system model, (capable of simulating one to four main parachute bodies), and to utilize a graphical program to animate the simulation results. To begin tackling the first task, I learned how to use SOMBAT by familiarizing myself with its mechanics and by understanding the methods used to tweak its various parameters and outputs. I then used this new knowledge to set up, run, and analyze many different situations within SOMBAT in order to explore the limitations of the parachute model. Some examples of parameters that I varied include the initial velocity and orientation of the falling capsule, the number of main parachutes, and the location where the parachutes were attached to the capsule. Each parameter changed would give a different output, and in some cases, would expose a bug or limitation in the model. A major bug that I discovered was the inability of the model to handle any number of parachutes other than three. I spent quite some time trying to debug the code logically, but was unable to figure it out until my mentor taught me that digital simulation limitations can occur when some approximations are mistakenly assumed for certain in a physical system. This led me to the realization that unlike in all of the programming classes

Personalized Age Progression with Bi-Level Aging Dictionary Learning.

Science.gov (United States)

Shu, Xiangbo; Tang, Jinhui; Li, Zechao; Lai, Hanjiang; Zhang, Liyan; Yan, Shuicheng

2018-04-01

Age progression is defined as aesthetically re-rendering the aging face at any future age for an individual face. In this work, we aim to automatically render aging faces in a personalized way. Basically, for each age group, we learn an aging dictionary to reveal its aging characteristics (e.g., wrinkles), where the dictionary bases corresponding to the same index yet from two neighboring aging dictionaries form a particular aging pattern cross these two age groups, and a linear combination of all these patterns expresses a particular personalized aging process. Moreover, two factors are taken into consideration in the dictionary learning process. First, beyond the aging dictionaries, each person may have extra personalized facial characteristics, e.g., mole, which are invariant in the aging process. Second, it is challenging or even impossible to collect faces of all age groups for a particular person, yet much easier and more practical to get face pairs from neighboring age groups. To this end, we propose a novel Bi-level Dictionary Learning based Personalized Age Progression (BDL-PAP) method. Here, bi-level dictionary learning is formulated to learn the aging dictionaries based on face pairs from neighboring age groups. Extensive experiments well demonstrate the advantages of the proposed BDL-PAP over other state-of-the-arts in term of personalized age progression, as well as the performance gain for cross-age face verification by synthesizing aging faces.

Distributed knowledge-based system for the optimum utilisation of South African wool

CSIR Research Space (South Africa)

Dlodlo, N

2009-09-01

Full Text Available combed yarn joints by artifi cial neural networks. Part 1: Developing an artifi cial neural network model, Fibres and Textiles in Eastern Europe, 13(1): 39-43. 20. Maly, R., Abdel-Wahab, H., Wild, C., Overstreet, C.M., Gupta, A., Abdel-Hamid, A...

78 FR 6068 - Proposed Information Collection; Comment Request; Interim Procedures for Considering Requests...

Science.gov (United States)

2013-01-29

... United States--Peru Trade Promotion Agreement (US-PERU TPA) AGENCY: International Trade [email protected] . SUPPLEMENTARY INFORMATION: I. Abstract The United States and Peru negotiated the US-Peru..., fabric, yarn, and fiber produced in Peru or the United States and traded between the two countries are...

Electrically conducting fibres for e-textiles : An open playground for conjugated polymers and carbon nanomaterials

NARCIS (Netherlands)

Lund, Anja; van der Velden, N.M.; Persson, Nils-Krister; Hamedi, Mahiar M.; Müller, Christian

2018-01-01

Conducting fibres and yarns promise to become an essential part of the next generation of wearable electronics that seamlessly integrate electronic function into one of the most versatile and most widely used form of materials: textiles. This review explores the many types of conducting fibres

Engineering of High-Toughness Carbon Nanotubes Hierarchically Laminated Composites

Science.gov (United States)

2012-01-27

Bernsmann, F.; Ersen, O.; Voegel, J.-C.; Jan, E.; Kotov, N. A.; Ball, V. Melanin -Containing Films: Growth from Dopamine Solutions versus Layer-by-Layer...Chen, Wei; Doty, Chris; Xu, Chuanlai; Kotov, Nicholas A.. Smart Electronic Yarns and Wearable Fabrics for Human Biomonitoring made by Carbon Nanotube

49 CFR 372.115 - Commodities that are not exempt under 49 U.S.C. 13506(a)(6).

Science.gov (United States)

2010-10-01

..., slaughtered Charcoal Cheese Coal Cocoa beans Coffee, beans, roasted, or instant Copra meal Cotton yarn... Flaxseed meal Flour Forest products: Resin products, such as turpentine Fruits and Berries: Bananas, fresh... extracted from grain Popcorn, popped Rice, precooked Wheat germ Gravel Hair, hog or other animal, product of...

PerformAge

DEFF Research Database (Denmark)

Fristrup, Tine

2012-01-01

are constituted as experts on aging. In the humanistic model of aging, the aging self becomes the expert on the process of becoming of age. Thi sconflicting aspect of the discursive battlefield on aging will be elaborated in the framework of PerformAge and understood as a temporal and spatial theorising of aging......: the poetics of aging. Making the lived experience the centrepiece of this paper, poetic representations of aging lives (Laurel Richardson, 1991, 1992) will articulate subjectively felt experiences in social encounters between people performing age. In writing the social (Dorothy E. Smith, 1999) encounters, I...... as a researcher perform age in the process of figuring the possible age performativities as subject positioning performativity (Judith Butler, 1995) in the social encounters and textualized in poetic representations. Inspired by the work on Reifungsromane (Barbara Frey Waxman, 1990), I do not want to paint...

Characterization and modeling of tensile behavior of ceramic woven fabric composites

Science.gov (United States)

Kuo, Wen-Shyong; Chen, Wennei Y.; Parvizi-Majidi, Azar; Chou, Tsu-Wei

1991-01-01

This paper examines the tensile behavior of SiC/SiC fabric composites. In the characterization effort, the stress-strain relation and damage evolution are studied with a series of loading and unloading tensile test experiments. The stress-strain relation is linear in response to the initial loading and becomes nonlinear when loading exceeds the proportional limit. Transverse cracking has been observed to be a dominant damage mode governing the nonlinear deformation. The damage is initiated at the inter-tow pores where fiber yarns cross over each other. In the modeling work, the analysis is based upon a fiber bundle model, in which fiber undulation in the warp and fill directions and gaps among fiber yarns have been taken into account. Two limiting cases of fabric stacking arrangements are studied. Closed form solutions are obtained for the composite stiffness and Poisson's ratio. Transverse cracking in the composite is discussed by applying a constant failure strain criterion.

Unit cell geometry of 3-D braided structures

Science.gov (United States)

Du, Guang-Wu; Ko, Frank K.

1993-01-01

The traditional approach used in modeling of composites reinforced by three-dimensional (3-D) braids is to assume a simple unit cell geometry of a 3-D braided structure with known fiber volume fraction and orientation. In this article, we first examine 3-D braiding methods in the light of braid structures, followed by the development of geometric models for 3-D braids using a unit cell approach. The unit cell geometry of 3-D braids is identified and the relationship of structural parameters such as yarn orientation angle and fiber volume fraction with the key processing parameters established. The limiting geometry has been computed by establishing the point at which yarns jam against each other. Using this factor makes it possible to identify the complete range of allowable geometric arrangements for 3-D braided preforms. This identified unit cell geometry can be translated to mechanical models which relate the geometrical properties of fabric preforms to the mechanical responses of composite systems.

The Influence of Knitting Structure on Heating and Cooling Dynamic

Directory of Open Access Journals (Sweden)

Daiva MIKUČIONIENĖ

2013-05-01

Full Text Available The comfort provided by clothing depends on several factors, one of them being thermal comfort. Human thermal comfort depends on a combination of clothing, climate, and physical activity. It is known, the fibre type, yarn properties, fabric structure, finishing are the main factors affecting thermo-physiological comfort. The thermal property of knitted fabric is very important not only for its thermal comfort but also for protection against cross weather conditions. Most of the studies carried out have been devoted to measure static thermal properties. But it is very important not only amount of the heat released to the environment but also the dynamics of the heat transmission. The main goal of this work was to investigate the dynamic of the heat and cool transfer through the fabrics with different knitting pattern and different type of the yarns. Three different types of knitted fabrics were developed for this experimental work.DOI: http://dx.doi.org/10.5755/j01.ms.19.2.4434

Complex of fiber and effects of mix spinning; Sen'i no fukugoka to konbo no koka

Energy Technology Data Exchange (ETDEWEB)

Matsui, N. [Asahi Chemical Industry Corp., Tokyo (Japan)

2000-03-01

In recently, comfortable life can be spent by performing complex of fibers. As complex of single fibers being materials of yarn, conjugate fiber is listed. Conjugate fiber is a fiber spun over 2 kind of polymer having different characteristics from one nozzle. There are sheath core type fibers as complex functional fibers. Static electricity prevention fibers can be prepared by putting conductive materials, for example, carbon black into core parts. After putting components being able to dissolve by specific solvents into core, hollow fibers can be prepared by dissolving core parts in near process to products. By reason of clothing contacting to skin directly in board aria and long time, fashionable characters of design and so on or comfortability of wearing are needed in many cases. In this reason, many kinds of fibers for clothing prepared complex yarn by being complex and by making the best use of good characteristics of each fibers, and developed a way to new function or new use. (NEDO)

Properties of hemp fibre polymer composites - An optimisation of fibre properties using novel defibration methods and fibre characterisation

DEFF Research Database (Denmark)

Thygesen, Anders

2006-01-01

Characterization of hemp fibres was carried out with fibres obtained with low handling damage and defibration damage to get an indication of how strong cellulose based fibres that can be produced from hemp. Comparison was made with hemp yarn producedunder traditional conditions where damage...... obtained by steam explosion of hemp fibres prior defibrated with pectin degrading enzymes. The S2 layer in the fibre wall of the hemp fibres consisted of1-4 cellulose rich and lignin poor concentric layers constructed of ca. 100 nm thick lamellae. The microfibril angle showed values in the range 0......-10° for the main part of the S2-layer and 70-90° for the S1-layer. The microfibrils that are mainly parallelwith the fibre axis explain the high fibre stiffness, which in defibrated hemp fibres reached 94 GPa. The defibrated hemp fibres had higher fibre stiffness (88-94 GPa) than hemp yarn (60 GPa), which...

Surface Coatings of TiO2 Nanoparticles onto the Designed Fabrics for Enhanced Self-Cleaning Properties

Directory of Open Access Journals (Sweden)

Mudassar Abbas

2018-01-01

Full Text Available Herein, the hydrophobic and self-cleaning properties of three different fabric surfaces have been evaluated after applying titanium dioxide (TiO2 nanofinishes. The nanoparticles were prepared by sol-gel techniques and were characterized by using X-ray diffraction (XRD, scanning electron microscopy (SEM and dynamic light scattering (DLS methods. The ultra-refined particles were applied over three different fabric substrates having similar weave of Z-twill (3/1. The yarns of 100% polyester, blend of viscose with mod-acrylic and high performance polyethylene containing 16 yarn count (Ne and 31.496 and 15.748 ends/cm and picks/cm, respectively, were used for required fabric preparation. The different fabric structures were applied with self-cleaning finish of TiO2 nanoparticles prepared in our laboratory and the results were compared with commercially available finish Rucoguard AFR. The static contact angles, UV-protection factor, air permeability and hydrophobic activity of nanofinished fabric helped in evaluating their breathability and self-cleaning properties.

36 CFR 327.4 - Aircraft.

Science.gov (United States)

2010-07-01

..., helicopters, ultra-light aircraft, motorized hang gliders, hot air balloons, any non-powered flight devices or..., material or equipment by parachute, balloon, helicopter or other means onto or from project lands or waters...

Subjective Age in Early Adolescence: Relationships with Chronological Age, Pubertal Timing, Desired Age, and Problem Behaviors

Science.gov (United States)

Hubley, Anita M.; Arim, Rubab G.

2012-01-01

Subjective age generally refers to the age that one feels. In a cross-sectional questionnaire study of 245 adolescents ages 10-14 years, we examined (a) whether, and when, a cross-over in subjective age occurs, (b) differences in subjective age among pubertal timing groups, (c) correlations between subjective age and each of desired age and five…

Evaluation of electromagnetic shielding effectiveness of multi-axial ...

Indian Academy of Sciences (India)

The usage of electrical and electronic equipments has been increasing in daily life, which has a potential hazardous impact on humans and other living organisms. In this paper, multi-axial fabrics containing steel yarns and carbon filaments, and their polyester (PES) resin-reinforced composites have been prepared for ...

Characterization of the dynamic friction of woven fabrics: Experimental methods and benchmark results

NARCIS (Netherlands)

Sachs, Ulrich; Akkerman, Remko; Fetfatsidis, K.; Vidal-Sallé, E.; Schumacher, J.; Ziegmann, G.; Allaoui, S.; Hivet, G.; Maron, B.; Vanclooster, K.; Lomov, S.V.

2014-01-01

A benchmark exercise was conducted to compare various friction test set-ups with respect to the measured coefficients of friction. The friction was determined between Twintex®PP, a fabric of commingled yarns of glass and polypropylene filaments, and a metal surface. The same material was supplied to

19 CFR 208.3 - Petitions.

Science.gov (United States)

2010-04-01

... demonstrates to the satisfaction of the Commission a proper interest in filing a petition. (b) Contents of... States, showing any conversion factors used (for example, most woven fabrics are reported in square... fabric or yarn to the customer identified in the order, and any other information that the interested...

Comparative Analysis of Immediate Response by National Disaster Management Systems of the U.S., Pakistan, and Turkey

Science.gov (United States)

2014-06-01

the existence of a regional or national disaster management system) include the U.S., the UK, Brazil , and New Zealand (Coppola 2006). 2...two big hotels , with 40 additional fatalities. In addition, 33,016 buildings, 28,532 housings, 2,440 workplaces, and 8,254 yarns were collapsed or

Learning Preferences and Impacts of Education Programs in Dog Health Programs in Five Rural and Remote Australian Indigenous Communities

Science.gov (United States)

Constable, Sophie; Dixon, Roselyn; Dixon, Robert

2011-01-01

As part of strategies to improve dog and community health in rural and remote Indigenous communities, this study investigated preferences and impacts of dog health education programs. Semistructured interviews with 63 residents from five communities explored learning preferences. Though each community differed, on average yarning was preferred by…

Deconstructive Misalignment: Archives, Events, and Humanities Approaches in Academic Development

Science.gov (United States)

Holmes, Trevor M.; Sutherland, Kathryn A.

2015-01-01

Using poetry, role play, readers' theatre, and creative manipulations of space through yarn and paper weaving, a workshop in 2008 challenged one of educational development's more pervasive and least questioned notions ("constructive alignment" associated most often with the work of John Biggs). This paper describes the reasoning behind…

Treatment of air dried archaeological wool textiles from waterlogged environment

DEFF Research Database (Denmark)

Scharff, Annemette Bruselius

2014-01-01

expanded the fibers and the yarn increased in size, resulting in more flexible and less brittle textiles. This property was kept when the textiles were dried by stepwise dehydration in ethanol, acetone, and white spirit with a final treatment in 5% lanolin. Preliminary tests on brittle textiles can...

Numerical Coupling and Simulation of Point-Mass System with the Turbulent Fluid Flow

Science.gov (United States)

Gao, Zheng

A computational framework that combines the Eulerian description of the turbulence field with a Lagrangian point-mass ensemble is proposed in this dissertation. Depending on the Reynolds number, the turbulence field is simulated using Direct Numerical Simulation (DNS) or eddy viscosity model. In the meanwhile, the particle system, such as spring-mass system and cloud droplets, are modeled using the ordinary differential system, which is stiff and hence poses a challenge to the stability of the entire system. This computational framework is applied to the numerical study of parachute deceleration and cloud microphysics. These two distinct problems can be uniformly modeled with Partial Differential Equations (PDEs) and Ordinary Differential Equations (ODEs), and numerically solved in the same framework. For the parachute simulation, a novel porosity model is proposed to simulate the porous effects of the parachute canopy. This model is easy to implement with the projection method and is able to reproduce Darcy's law observed in the experiment. Moreover, the impacts of using different versions of k-epsilon turbulence model in the parachute simulation have been investigated and conclude that the standard and Re-Normalisation Group (RNG) model may overestimate the turbulence effects when Reynolds number is small while the Realizable model has a consistent performance with both large and small Reynolds number. For another application, cloud microphysics, the cloud entrainment-mixing problem is studied in the same numerical framework. Three sets of DNS are carried out with both decaying and forced turbulence. The numerical result suggests a new way parameterize the cloud mixing degree using the dynamical measures. The numerical experiments also verify the negative relationship between the droplets number concentration and the vorticity field. The results imply that the gravity has fewer impacts on the forced turbulence than the decaying turbulence. In summary, the

75 FR 75619 - Waiver of Acceptable Mission Risk Restriction for Reentry and a Reentry Vehicle

Science.gov (United States)

2010-12-06

... the International Space Station. 10. Dragon has redundant drogue parachutes and dual redundant main... waiver ``in a timely fashion.'' As such, the FAA has found that SpaceX had good cause for submitting its...

School Starting Age and the Crime-Age Profile

DEFF Research Database (Denmark)

Landersø, Rasmus; Nielsen, Helena Skyt; Simonsen, Marianne

2017-01-01

This paper uses register-based data to investigate the effects of school starting age on crime. Through this, we provide insights into the determinants of crime-age profiles. We exploit that Danish children typically start first grade in the calendar year they turn seven, which gives rise...... to a discontinuity in school starting age for children born around New Year. Our analysis speaks against a simple invariant crime-age profile as is popular in criminology: we find that higher school starting age lowers the propensity to commit crime at young ages. We also find effects on the number of crimes...

A biomimetic multilayer nanofiber fabric fabricated by electrospinning and textile technology from polylactic acid and Tussah silk fibroin as a scaffold for bone tissue engineering

International Nuclear Information System (INIS)

Shao, Weili; He, Jianxin; Han, Qiming; Sang, Feng; Wang, Qian; Chen, Li; Cui, Shizhong

2016-01-01

To engineer bone tissue, a scaffold with good biological properties should be provided to approximate the hierarchical structure of collagen fibrils in natural bone. In this study, we fabricated a novel scaffold consisting of multilayer nanofiber fabrics (MLNFFs) by weaving nanofiber yarns of polylactic acid (PLA) and Tussah silk fibroin (TSF). The yarns were fabricated by electrospinning, and we found that spinnability, as well as the mechanical properties of the resulting scaffold, was determined by the ratio between polylactic acid and Tussah silk fibroin. In particular, a 9:1 mixture can be spun continuously into nanofiber yarns with narrow diameter distribution and good mechanical properties. Accordingly, woven scaffolds based on this mixture had excellent mechanical properties, with Young's modulus 417.65 MPa and tensile strength 180.36 MPa. For nonwoven scaffolds fabricated from the same materials, the Young's modulus and tensile strength were 2- and 4-fold lower, respectively. Woven scaffolds also supported adhesion and proliferation of mouse mesenchymal stem cells, and promoted biomineralization via alkaline phosphatase and mineral deposition. Finally, the scaffolds significantly enhanced the formation of new bone in damaged femoral condyle in rabbits. Thus, the scaffolds are potentially suitable for bone tissue engineering because of biomimetic architecture, excellent mechanical properties, and good biocompatibility. - Highlights: • A novel strategy to mimic the hierarchical collagen fibril in bone is proposed by electrospinning and conventional textile technology. • The tensile strength of the woven scaffold was nearly 4-fold larger than that of nonwoven mats. • The nanofiber woven scaffolds show excellent cytocompatibility and accelerate osteoblast differentiation. • The composite scaffold significantly enhanced formation of new bone in damaged condyles in rabbit femur.

A biomimetic multilayer nanofiber fabric fabricated by electrospinning and textile technology from polylactic acid and Tussah silk fibroin as a scaffold for bone tissue engineering

Energy Technology Data Exchange (ETDEWEB)

Shao, Weili [Key Laboratory of Advanced Textile Composites, Ministry of Education, Institute of Textile Composites, Tianjin Polytechnic University, Tianjin 300387 (China); Henan provincial key laboratory of functional textile materials, Zhongyuan University of Technology, Zhengzhou 450007 (China); Collaborative Innovation Center of Textile and Garment Industry, Henan Province, Zhengzhou 450007 (China); He, Jianxin, E-mail: hejianxin771117@163.com [Henan provincial key laboratory of functional textile materials, Zhongyuan University of Technology, Zhengzhou 450007 (China); Collaborative Innovation Center of Textile and Garment Industry, Henan Province, Zhengzhou 450007 (China); Han, Qiming [Henan provincial key laboratory of functional textile materials, Zhongyuan University of Technology, Zhengzhou 450007 (China); Collaborative Innovation Center of Textile and Garment Industry, Henan Province, Zhengzhou 450007 (China); Sang, Feng [Department of Acquired Immune Deficiency Syndrome Treatment and Research Center, The First Affiliated Hospital of Henan University of Traditional Chinese Medicine, Zhengzhou 450000 (China); Wang, Qian [Henan provincial key laboratory of functional textile materials, Zhongyuan University of Technology, Zhengzhou 450007 (China); Collaborative Innovation Center of Textile and Garment Industry, Henan Province, Zhengzhou 450007 (China); Chen, Li [Key Laboratory of Advanced Textile Composites, Ministry of Education, Institute of Textile Composites, Tianjin Polytechnic University, Tianjin 300387 (China); Cui, Shizhong [Key Laboratory of Advanced Textile Composites, Ministry of Education, Institute of Textile Composites, Tianjin Polytechnic University, Tianjin 300387 (China); Henan provincial key laboratory of functional textile materials, Zhongyuan University of Technology, Zhengzhou 450007 (China); Collaborative Innovation Center of Textile and Garment Industry, Henan Province, Zhengzhou 450007 (China); and others

2016-10-01

To engineer bone tissue, a scaffold with good biological properties should be provided to approximate the hierarchical structure of collagen fibrils in natural bone. In this study, we fabricated a novel scaffold consisting of multilayer nanofiber fabrics (MLNFFs) by weaving nanofiber yarns of polylactic acid (PLA) and Tussah silk fibroin (TSF). The yarns were fabricated by electrospinning, and we found that spinnability, as well as the mechanical properties of the resulting scaffold, was determined by the ratio between polylactic acid and Tussah silk fibroin. In particular, a 9:1 mixture can be spun continuously into nanofiber yarns with narrow diameter distribution and good mechanical properties. Accordingly, woven scaffolds based on this mixture had excellent mechanical properties, with Young's modulus 417.65 MPa and tensile strength 180.36 MPa. For nonwoven scaffolds fabricated from the same materials, the Young's modulus and tensile strength were 2- and 4-fold lower, respectively. Woven scaffolds also supported adhesion and proliferation of mouse mesenchymal stem cells, and promoted biomineralization via alkaline phosphatase and mineral deposition. Finally, the scaffolds significantly enhanced the formation of new bone in damaged femoral condyle in rabbits. Thus, the scaffolds are potentially suitable for bone tissue engineering because of biomimetic architecture, excellent mechanical properties, and good biocompatibility. - Highlights: • A novel strategy to mimic the hierarchical collagen fibril in bone is proposed by electrospinning and conventional textile technology. • The tensile strength of the woven scaffold was nearly 4-fold larger than that of nonwoven mats. • The nanofiber woven scaffolds show excellent cytocompatibility and accelerate osteoblast differentiation. • The composite scaffold significantly enhanced formation of new bone in damaged condyles in rabbit femur.

Multiple faces of contemporary hand knitting

Science.gov (United States)

Pavko-Čuden, A.

2017-10-01

Knitting and crocheting are traditional textile techniques with great significance both in history and modern times. Similar to other textile techniques, knitting has developed into a diversified industrial sector, comprising the production of knitted fabrics, knitwear, hosiery and fashion accessories. At the same time, contemporary knitting and crocheting became hobbies as well as arts-and-crafts activities, extending to various areas of work and leisure. Historical and traditional ethnic knitting and crocheting patterns keep inspiring designers’ collections and also other industrial products. Not so long ago, knitting was seen as an ordinary and unchanging indoor activity and, in its domestic history, it was the preserve of older women making products of dainty work and taste. Today, knitting deals with urban population of all classes. The popularity of leisure hand knitting is increasing; moreover, hand knitting is becoming more and more widespread among young people. With the emergence of artistic and handicraft markets, hand-knitting and crocheting developed into a profitable market activity. Positive effects of hand knitting have become increasingly important - from generating creativity and innovativeness, through knitting and socializing in groups, to medical and therapeutic effects as well as social and global connections. Yarn bombing, yarn storming or graffiti knitting has been used to describe urban social practices of knitted objects placed, or tagged, in public spaces. Knitting became means of communication, artistic and social expression and statement. The advantage of hand knitting is its mobility. One can knit almost everywhere, and for hand knitting, only a ball of yarn and knitting needles are required. Handknitted products have nice touch, they are custom-made and therefore personalized.

Molecular Dynamics Modeling of Carbon Nanotube Composite Fracture Using ReaxFF

Science.gov (United States)

Jensen, Benjamin D.; Wise, Kristopher E.; Odegard, Gregory M.

2016-01-01

Carbon nanotube (CNT) fiber reinforced composites with specific tensile strengths and moduli approaching those of aerospace grade carbon fiber composites have recently been reported. This achievement was enabled by the emerging availability of high N/tex yarns in kilometer-scale quantities. While the production of this yarn is an impressive advance, its strength is still much lower than that of the individual CNTs comprising the yarn. Closing this gap requires understanding load transfer between CNTs at the nanometer dimensional scale. This work uses reactive molecular dynamics simulations to gain an understanding at the nanometer scale of the key factors that determine CNT nanocomposite mechanical performance, and to place more realistic upper bounds on the target properties. While molecular dynamics simulations using conventional force fields can predict elastic properties, the ReaxFF reactive forcefield can also model fracture behavior because of its ability to accurately describe bond breaking and formation during a simulation. The upper and lower bounds of CNT composite properties are investigated by comparing systems composed of CNTs continuously connected across the periodic boundary with systems composed of finite length CNTs. These lengths, effectively infinite for the continuous tubes and an aspect ratio of 13 for the finite length case, result from practical limitations on the number of atoms that can be included in a simulation. Experimentally measured aspect ratios are typically on the order of 100,000, so the calculated results should represent upper and lower limits on experimental mechanical properties. Finally, the effect of various degrees of covalent crosslinking between the CNTs and amorphous carbon matrix is considered to identify the amount of CNT-matrix covalent bonding that maximizes overall composite properties.

Multiscale Modeling of Carbon Fiber Reinforced Polymer (CFRP) for Integrated Computational Materials Engineering Process

Energy Technology Data Exchange (ETDEWEB)

Gao, Jiaying; Liang, Biao; Zhang, Weizhao; Liu, Zeliang; Cheng, Puikei; Bostanabad, Ramin; Cao, Jian; Chen, Wei; Liu, Wing Kam; Su, Xuming; Zeng, Danielle; Zhao, John

2017-10-23

In this work, a multiscale modeling framework for CFRP is introduced to study hierarchical structure of CFRP. Four distinct scales are defined: nanoscale, microscale, mesoscale, and macroscale. Information at lower scales can be passed to higher scale, which is beneficial for studying effect of constituents on macroscale part’s mechanical property. This bottom-up modeling approach enables better understanding of CFRP from finest details. Current study focuses on microscale and mesoscale. Representative volume element is used at microscale and mesoscale to model material’s properties. At microscale, unidirection CFRP (UD) RVE is used to study properties of UD. The UD RVE can be modeled with different volumetric fraction to encounter non-uniform fiber distribution in CFRP part. Such consideration is important in modeling uncertainties at microscale level. Currently, we identified volumetric fraction as the only uncertainty parameters in UD RVE. To measure effective material properties of UD RVE, periodic boundary conditions (PBC) are applied to UD RVE to ensure convergence of obtained properties. Properties of UD is directly used at mesoscale woven RVE modeling, where each yarn is assumed to have same properties as UD. Within woven RVE, there can be many potential uncertainties parameters to consider for a physical modeling of CFRP. Currently, we will consider fiber misalignment within yarn and angle between wrap and weft yarns. PBC is applied to woven RVE to calculate its effective material properties. The effect of uncertainties are investigated quantitatively by Gaussian process. Preliminary results of UD and Woven study are analyzed for efficacy of the RVE modeling. This work is considered as the foundation for future multiscale modeling framework development for ICME project.