In situ measurements of oxygen dynamics in unsaturated archaeological deposits

DEFF Research Database (Denmark)

Matthiesen, Henning; Hollesen, Jørgen; Dunlop, Rory

2015-01-01

Oxygen is a key parameter in the degradation of archaeological material, but little is known of its dynamics in situ. In this study, 10 optical oxygen sensors placed in a 2 m deep test pit in the cultural deposits at Bryggen in Bergen have monitored oxygen concentrations every half hour for more ...... of the soil exceeds 10–15% vol, while oxygen dissolved in infiltrating rainwater is of less importance for the supply of oxygen in the unsaturated zone....... than a year. It is shown that there is a significant spatial and temporal variation in the oxygen concentration, which is correlated to measured soil characteristics, precipitation, soil water content and degradation of organic material. In these deposits oxygen typically occurs when the air content...

Depleted uranium. A post-war disaster for environment and health

International Nuclear Information System (INIS)

Diehl, P.; Fahey, D.; Bertell, R.; Robicheau, D.; Bristow, R.; Arbuthnot, F.; Van der Keur, H.

1999-05-01

In the course of the preparations for the The Hague Appeal for Peace '99 conference in the Netherlands, Laka decided to make a brochure about the use of depleted uranium in conventional weaponry and its consequences. The idea was born because of the short time reserved during the session for the presentation of all details about depleted uranium (DU). Although the word 'depleted uranium' may suggest no harmful impact from radiation, this brochure will clarify the real radiotoxic (and chemotoxic) properties of DU. Laka asked several 'insiders' to take part in the completion of the brochure. Thanks to their efforts, we have been able to present well-documented articles for activists, scientists, scholars and students to share with them valuable information about the hazardous impact of DU contamination and its consequences on human health and the environment. Taking notice of the growing military use of DU, we must consider not only the increased threats of radioactive battlefields but also the whole dirty cycle in the uranium industry connected with the DU technology and its impact on health and the environment in the surroundings of test areas and in the uranium industry itself. The contents of all the contributions are under the responsibility of the authors.The titles of the contributions are (1) Depleted uranium. A by-product of the nuclear chain; (2) Depleted uranium weapons. Lessons from the 1991 Gulf War; (3) Gulf War veterans and depleted uranium; (4) The next testing site for depleted uranium weaponry; (5) Depleted uranium. The thoughts of the first British Gulf War veteran to be tested for, and found to be poisoned with depleted uranium; (6) The health of the Iraqi people; (7) Uranium pollution from the amsterdam 1992 plane crash; and (8) an overview od organizations involved in campaigns against depleted uranium. refs

Radio-frequency oxygen-plasma-enhanced pulsed laser deposition of IGZO films

Science.gov (United States)

Chou, Chia-Man; Lai, Chih-Chang; Chang, Chih-Wei; Wen, Kai-Shin; Hsiao, Vincent K. S.

2017-07-01

We demonstrate the crystalline structures, optical transmittance, surface and cross-sectional morphologies, chemical compositions, and electrical properties of indium gallium zinc oxide (IGZO)-based thin films deposited on glass and silicon substrates through pulsed laser deposition (PLD) incorporated with radio-frequency (r.f.)-generated oxygen plasma. The plasma-enhanced pulsed laser deposition (PEPLD)-based IGZO thin films exhibited a c-axis-aligned crystalline (CAAC) structure, which was attributed to the increase in Zn-O under high oxygen vapor pressure (150 mTorr). High oxygen vapor pressure (150 mTorr) and low r.f. power (10 W) are the optimal deposition conditions for fabricating IGZO thin films with improved electrical properties.

Effect of argon addition into oxygen atmosphere on YBCO thin films deposition

International Nuclear Information System (INIS)

Mozhaev, P. B.; Borisenko, I. V.; Ovsyannikov, G. A.; Kuehle, A.; Bindslev-Hansen, J.; Johannes, L.; Skov, J. L.

2002-01-01

Multicomponent nature of the YBa 2 Cu 3 O x (YBCO) high-temperature superconductor makes difficult fabrication of smooth thin films: every local deviation from stoichiometry can result in seeding of a non-superconducting oxide particle. High density of such particles on typical YBCO thin film surface, however, presumes overall non-stoichiometry of the film. Such an effect can result from (i) non-uniform material transport from target to substrate, and (ii) re-evaporation or re-sputtering from the growing film surface. The first reason is more usual for laser ablation deposition technique, the second is typical for long sputtering deposition processes. Substitution of oxygen with argon in the deposition atmosphere improves surface quality of YBCO thin films deposited both by laser ablation and DC-sputtering at high pressure techniques. In the first case, the ablated species are scattered different ways in the oxygen atmosphere. Addition of argon decreases the inelastic scattering of barium; the proper part of Ar in the deposition atmosphere makes scattering and, hence, transport of all atoms uniform. The YBCO films deposited by DC-sputtering at high pressure technique are Ba-deficient also, but the reason is re-sputtering of Ba from the growing film as a result of negative oxygen ions bombardment. Such bombardment can lead also to chemical interaction of the deposited material with the substrate, as in the case of deposition of YBCO thin film on the CeO 2 buffer layer on sapphire. Substitution of oxygen with argon not only suppresses ion bombardment of the film, but also increases discharge stability due to presence of positive Ar + ions. The limiting factor of argon substitution is sufficient oxygenation of the growing oxide film. When oxygen partial pressure is too small, the superconducting quality of the YBCO thin film decreases and such a decrease cannot be overcome by prolonged oxygenation after deposition. (Authors)

Radio-frequency oxygen-plasma-enhanced pulsed laser deposition of IGZO films

Directory of Open Access Journals (Sweden)

Chia-Man Chou

2017-07-01

Full Text Available We demonstrate the crystalline structures, optical transmittance, surface and cross-sectional morphologies, chemical compositions, and electrical properties of indium gallium zinc oxide (IGZO-based thin films deposited on glass and silicon substrates through pulsed laser deposition (PLD incorporated with radio-frequency (r.f.-generated oxygen plasma. The plasma-enhanced pulsed laser deposition (PEPLD-based IGZO thin films exhibited a c-axis-aligned crystalline (CAAC structure, which was attributed to the increase in Zn-O under high oxygen vapor pressure (150 mTorr. High oxygen vapor pressure (150 mTorr and low r.f. power (10 W are the optimal deposition conditions for fabricating IGZO thin films with improved electrical properties.

Microsensor and transcriptomic signatures of oxygen depletion in biofilms associated with chronic wounds: Biofilms and oxygen

Energy Technology Data Exchange (ETDEWEB)

James, Garth A. [Center for Biofilm Engineering, Montana State University, Bozeman Montana; Ge Zhao, Alice [Division of Dermatology, Department of Medicine, University of Washington, Seattle Washington; Usui, Marcia [Division of Dermatology, Department of Medicine, University of Washington, Seattle Washington; Underwood, Robert A. [Division of Dermatology, Department of Medicine, University of Washington, Seattle Washington; Nguyen, Hung [The Gene and Linda Voiland School of Chemical Engineering and Bioengineering, Washington State University, Pullman Washington; Beyenal, Haluk [The Gene and Linda Voiland School of Chemical Engineering and Bioengineering, Washington State University, Pullman Washington; deLancey Pulcini, Elinor [Center for Biofilm Engineering, Montana State University, Bozeman Montana; Agostinho Hunt, Alessandra [Department of Microbiology and Molecular Genetics, 5180 Biomedical and Physical Sciences, Michigan State University, East Lansing Michigan; Bernstein, Hans C. [Pacific Northwest National Laboratory, Chemical and Biological Signature Science, Richland Washington; Fleckman, Philip [Division of Dermatology, Department of Medicine, University of Washington, Seattle Washington; Olerud, John [Division of Dermatology, Department of Medicine, University of Washington, Seattle Washington; Williamson, Kerry S. [Center for Biofilm Engineering, Montana State University, Bozeman Montana; Franklin, Michael J. [Center for Biofilm Engineering, Montana State University, Bozeman Montana; Stewart, Philip S. [Center for Biofilm Engineering, Montana State University, Bozeman Montana

2016-02-16

Polymicrobial biofilms have been implicated in delayed wound healing, although the mechanisms by which biofilms impair wound healing are poorly understood. Many species of bacteria produce exotoxins and exoenzymes that may inhibit healing. In addition, oxygen consumption by biofilms may impede wound healing. In this study, we used oxygen microsensors to measure oxygen transects through in vitro-cultured biofilms, biofilms formed in vivo in a diabetic (db/db) mouse model, and ex vivo human chronic wound specimens. The results show that oxygen levels within both euthanized and live mouse wounds had steep gradients that reached minima ranging from 19 to 61% oxygen partial pressure, compared to atmospheric oxygen levels. The oxygen gradients in the mouse wounds were similar to those observed for clinical isolates cultured in vitro and for human ex vivo scabs. No oxygen gradients were observed for heat-killed scabs, suggesting that active metabolism by the viable bacteria contributed to the reduced oxygen partial pressure of the wounds. To characterize the metabolic activities of the bacteria in the mouse wounds, we performed transcriptomics analyses of Pseudomonas aeruginosa biofilms associated with the db/db mice wounds using Affymetrix microarrays. The results demonstrated that the bacteria expressed genes for metabolic activities associated with cell growth. Interestingly, the transcriptome results indicated that the bacteria within the wounds also experienced oxygen-limitation stress. Among the bacterial genes that were expressed in vivo were genes associated with the Anr-mediated hypoxia-stress response. Other bacterial stress response genes highly expressed in vivo were genes associated with stationary-phase growth, osmotic stress, and RpoH-mediated heat shock stress. Overall, the results support the hypothesis that the metabolic activities of bacteria in biofilms act as oxygen sinks in chronic wounds and that the depletion of oxygen contributes to the

Benthic foraminifera as proxy for oxygen-depleted conditions off the central west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Nigam, R.; Mazumder, A.; Henriques, P.J.; Saraswat, R.

In order to study the response of benthic foraminifera, especially the rectilinear bi- and tri-serial benthic foraminifera (RBF) to oxygen-depleted conditions from the Arabian Sea off central west coast of India, 103 surface sediment samples...

Macrophage Depletion Attenuates Extracellular Matrix Deposition and Ductular Reaction in a Mouse Model of Chronic Cholangiopathies

Science.gov (United States)

Syn, Wing-Kin; Lagaisse, Kimberly; van Hul, Noemi; Heindryckx, Femke; Sowa, Jan-Peter; Peeters, Liesbeth; Van Vlierberghe, Hans; Leclercq, Isabelle A.; Canbay, Ali

2016-01-01

Chronic cholangiopathies, such as primary and secondary sclerosing cholangitis, are progressive disease entities, associated with periportal accumulation of inflammatory cells, encompassing monocytes and macrophages, peribiliary extracellular matrix (ECM) deposition and ductular reaction (DR). This study aimed to elucidate the relevance of macrophages in the progression of chronic cholangiopathies through macrophage depletion in a 3,5-diethoxycarbonyl-1,4-dihydrocollidine (DDC) mouse model. One group of mice received a single i.p. injection of Clodronate encapsulated liposomes (CLOLipo) at day 7 of a 14 day DDC treatment, while control animals were co-treated with PBSLipo instead. Mice were sacrificed after 7 or respectively 14 days of treatment for immunohistochemical assessment of macrophage recruitment (F4/80), ECM deposition (Sirius Red, Laminin) and DR (CK19). Macrophage depletion during a 14 day DDC treatment resulted in a significant inhibition of ECM deposition. Porto-lobular migration patterns of laminin-rich ECM and ductular structures were significantly attenuated and a progression of DR was effectively inhibited by macrophage depletion. CLOLipo co-treatment resulted in a confined DR to portal regions without amorphous cell clusters. This study suggests that therapeutic options selectively directed towards macrophages might represent a feasible treatment for chronic cholestatic liver diseases. PMID:27618307

Effect of electron affinic hypoxic cell sensitizers on the radiolytic depletion of oxygen in mammalian cells irradiated at ultrahigh dose rates

International Nuclear Information System (INIS)

Michaels, H.B.

1982-01-01

When CHO cells are equilibrated with a low level of oxygen (e.g. 0.4% O 2 ) and irradiated with single 3 ns pulses of electrons, a breaking survival curve is observed. This effect is believed to be the result of radiolytic oxygen depletion and can be prevented by the presence of a relatively low concentraton of hypoxic cell radiosensitizer. This prevention of the breaking survival curve has been observed for 2- and 5-nitroimidazoles, nitrofurans, and diamide. It is hypothesized that the sensitizer acts by competing wth oxygen for the radiation-induced intracellular oxygen-binding species, perhaps a hydrated electron adduct, leaving oxygen free to participate in radiosensitization reactions during the lifetime of the oxygen-sensitive radiation-induced target sites for lethal damage, probably DNA radicals produced by hydroxyl radical attack. The proposed role of the sensitizer in the interference with oxygen depletion is a transient phenomenon, occuring on the microsecond to millisecond time scale

Influence of Oxygen Partial Pressure during Processing on the Thermoelectric Properties of Aerosol-Deposited CuFeO₂.

Science.gov (United States)

Stöcker, Thomas; Exner, Jörg; Schubert, Michael; Streibl, Maximilian; Moos, Ralf

2016-03-24

In the field of thermoelectric energy conversion, oxide materials show promising potential due to their good stability in oxidizing environments. Hence, the influence of oxygen partial pressure during synthesis on the thermoelectric properties of Cu-Delafossites at high temperatures was investigated in this study. For these purposes, CuFeO₂ powders were synthetized using a conventional mixed-oxide technique. X-ray diffraction (XRD) studies were conducted to determine the crystal structures of the delafossites associated with the oxygen content during the synthesis. Out of these powders, films with a thickness of about 25 µm were prepared by the relatively new aerosol-deposition (AD) coating technique. It is based on a room temperature impact consolidation process (RTIC) to deposit dense solid films of ceramic materials on various substrates without using a high-temperature step during the coating process. On these dense CuFeO₂ films deposited on alumina substrates with electrode structures, the Seebeck coefficient and the electrical conductivity were measured as a function of temperature and oxygen partial pressure. We compared the thermoelectric properties of both standard processed and aerosol deposited CuFeO₂ up to 900 °C and investigated the influence of oxygen partial pressure on the electrical conductivity, on the Seebeck coefficient and on the high temperature stability of CuFeO₂. These studies may not only help to improve the thermoelectric material in the high-temperature case, but may also serve as an initial basis to establish a defect chemical model.

The corrosion of depleted uranium in terrestrial and marine environments

International Nuclear Information System (INIS)

Toque, C.; Milodowski, A.E.; Baker, A.C.

2014-01-01

Depleted Uranium alloyed with titanium is used in armour penetrating munitions that have been fired in a number of conflict zones and testing ranges including the UK ranges at Kirkcudbright and Eskmeals. The study presented here evaluates the corrosion of DU alloy cylinders in soil on these two UK ranges and in the adjacent marine environment of the Solway Firth. The estimated mean initial corrosion rates and times for complete corrosion range from 0.13 to 1.9 g cm −2 y −1 and 2.5–48 years respectively depending on the particular physical and geochemical environment. The marine environment at the experimental site was very turbulent. This may have caused the scouring of corrosion products and given rise to a different geochemical environment from that which could be easily duplicated in laboratory experiments. The rate of mass loss was found to vary through time in one soil environment and this is hypothesised to be due to pitting increasing the surface area, followed by a build up of corrosion products inhibiting further corrosion. This indicates that early time measurements of mass loss or corrosion rate may be poor indicators of late time corrosion behaviour, potentially giving rise to incorrect estimates of time to complete corrosion. The DU alloy placed in apparently the same geochemical environment, for the same period of time, can experience very different amounts of corrosion and mass loss, indicating that even small variations in the corrosion environment can have a significant effect. These effects are more significant than other experimental errors and variations in initial surface area. -- Highlights: ► In-situ experiments were conducted to evaluate corrosion rates of depleted uranium. ► Samples were corroded in marine sediments, open sea water and two terrestrial soils. ► The depleted uranium titanium alloy corroded fastest in the marine environments. ► Rates of mass loss can vary through time if corrosion products are not removed. �

A study on hydrogen, oxygen, carbon, sulfur and lead isotopes in the rich uranium deposit No.201

International Nuclear Information System (INIS)

Li Yuexiang; Li Tiangang; Tong Hongshou; Feng Mingyue; Xu Zhan

1995-01-01

The uranium deposit No.201 located in Indonesian granite is one of the richest uranium deposits of granite type in China. An attempt is made to investigate the sources of ore-forming solutions and ore-forming materials, and to presume the environment of ore formation in the light of the study on composition of stable isotopes such as hydrogen, oxygen, carbon, sulfur and lead. The research results indicate that the ore-forming fluids in the deposit is mainly composed of meteoric water, the ore-forming materials principally came from pre-Yanshanian granite Massif and possibly, partly from the lower crust, and metallogenesis was undertaken under relatively stable physicochemical conditions

A study on hydrogen, oxygen, carbon, sulfur and lead isotopes in the rich uranium deposit No.201

Energy Technology Data Exchange (ETDEWEB)

Yuexiang, Li; Tiangang, Li; Hongshou, Tong; Mingyue, Feng; Zhan, Xu [Beijing Research Inst. of Uranium Geology (China)

1995-09-01

The uranium deposit No.201 located in Indonesian granite is one of the richest uranium deposits of granite type in China. An attempt is made to investigate the sources of ore-forming solutions and ore-forming materials, and to presume the environment of ore formation in the light of the study on composition of stable isotopes such as hydrogen, oxygen, carbon, sulfur and lead. The research results indicate that the ore-forming fluids in the deposit is mainly composed of meteoric water, the ore-forming materials principally came from pre-Yanshanian granite Massif and possibly, partly from the lower crust, and metallogenesis was undertaken under relatively stable physicochemical conditions.

Oxygen-reducing catalyst layer

Science.gov (United States)

O'Brien, Dennis P [Maplewood, MN; Schmoeckel, Alison K [Stillwater, MN; Vernstrom, George D [Cottage Grove, MN; Atanasoski, Radoslav [Edina, MN; Wood, Thomas E [Stillwater, MN; Yang, Ruizhi [Halifax, CA; Easton, E Bradley [Halifax, CA; Dahn, Jeffrey R [Hubley, CA; O'Neill, David G [Lake Elmo, MN

2011-03-22

An oxygen-reducing catalyst layer, and a method of making the oxygen-reducing catalyst layer, where the oxygen-reducing catalyst layer includes a catalytic material film disposed on a substrate with the use of physical vapor deposition and thermal treatment. The catalytic material film includes a transition metal that is substantially free of platinum. At least one of the physical vapor deposition and the thermal treatment is performed in a processing environment comprising a nitrogen-containing gas.

Dissolved oxygen sensing using organometallic dyes deposited within a microfluidic environment

Science.gov (United States)

Chen, Q. L.; Ho, H. P.; Jin, L.; Chu, B. W.-K.; Li, M. J.; Yam, V. W.-W.

2008-02-01

This work primarily aims to integrate dissolved oxygen sensing capability with a microfluidic platform containing arrays of micro bio-reactors or bio-activity indicators. The measurement of oxygen concentration is of significance for a variety of bio-related applications such as cell culture and gene expression. Optical oxygen sensors based on luminescence quenching are gaining much interest in light of their low power consumption, quick response and high analyte sensitivity in comparison to similar oxygen sensing devices. In our microfluidic oxygen sensor device, a thin layer of oxygen-sensitive luminescent organometallic dye is covalently bonded to a glass slide. Micro flow channels are formed on the glass slide using patterned PDMS (Polydimethylsiloxane). Dissolved oxygen sensing is then performed by directing an optical excitation probe beam to the area of interest within the microfluidic channel. The covalent bonding approach for sensor layer formation offers many distinct advantages over the physical entrapment method including minimizing dye leaching, ensuring good stability and fabrication simplicity. Experimental results confirm the feasibility of the device.

Base cation depletion, eutrophication and acidification of species-rich grasslands in response to long-term simulated nitrogen deposition

Energy Technology Data Exchange (ETDEWEB)

Horswill, Paul [Department of Animal and Plant Sciences, University of Sheffield, Alfred Denny Building, Western Bank, Sheffield S10 2TN (United Kingdom)], E-mail: paul.horswill@naturalengland.org.uk; O' Sullivan, Odhran; Phoenix, Gareth K.; Lee, John A.; Leake, Jonathan R. [Department of Animal and Plant Sciences, University of Sheffield, Alfred Denny Building, Western Bank, Sheffield S10 2TN (United Kingdom)

2008-09-15

Pollutant nitrogen deposition effects on soil and foliar element concentrations were investigated in acidic and limestone grasslands, located in one of the most nitrogen and acid rain polluted regions of the UK, using plots treated for 8-10 years with 35-140 kg N ha{sup -2} y{sup -1} as NH{sub 4}NO{sub 3}. Historic data suggests both grasslands have acidified over the past 50 years. Nitrogen deposition treatments caused the grassland soils to lose 23-35% of their total available bases (Ca, Mg, K, and Na) and they became acidified by 0.2-0.4 pH units. Aluminium, iron and manganese were mobilised and taken up by limestone grassland forbs and were translocated down the acid grassland soil. Mineral nitrogen availability increased in both grasslands and many species showed foliar N enrichment. This study provides the first definitive evidence that nitrogen deposition depletes base cations from grassland soils. The resulting acidification, metal mobilisation and eutrophication are implicated in driving floristic changes. - Nitrogen deposition causes base cation depletion, acidification and eutrophication of semi-natural grassland soils.

NEBULAR WATER DEPLETION AS THE CAUSE OF JUPITER'S LOW OXYGEN ABUNDANCE

International Nuclear Information System (INIS)

Mousis, Olivier; Lunine, Jonathan I.; Madhusudhan, Nikku; Johnson, Torrence V.

2012-01-01

Motivated by recent spectroscopic observations suggesting that atmospheres of some extrasolar giant planets are carbon-rich, i.e., carbon/oxygen ratio (C/O) ≥ 1, we find that the whole set of compositional data for Jupiter is consistent with the hypothesis that it should be a carbon-rich giant planet. We show that the formation of Jupiter in the cold outer part of an oxygen-depleted disk (C/O ∼ 1) reproduces the measured Jovian elemental abundances at least as well as the hitherto canonical model of Jupiter formed in a disk of solar composition (C/O 0.54). The resulting O abundance in Jupiter's envelope is then moderately enriched by a factor of ∼2 × solar (instead of ∼7 × solar) and is found to be consistent with values predicted by thermochemical models of the atmosphere. That Jupiter formed in a disk with C/O ∼ 1 implies that water ice was heterogeneously distributed over several AU beyond the snow line in the primordial nebula and that the fraction of water contained in icy planetesimals was a strong function of their formation location and time. The Jovian oxygen abundance to be measured by NASA's Juno mission en route to Jupiter will provide a direct and strict test of our predictions.

Calcium-dependent depletion zones in the cortical microtubule array coincide with sites of, but do not regulate, wall ingrowth papillae deposition in epidermal transfer cells

Science.gov (United States)

Zhang, Hui-ming; Talbot, Mark J.; McCurdy, David W.; Patrick, John W.; Offler, Christina E.

2015-01-01

Trans-differentiation to a transfer-cell morphology is characterized by the localized deposition of wall ingrowth papillae that protrude into the cytosol. Whether the cortical microtubule array directs wall ingrowth papillae formation was investigated using a Vicia faba cotyledon culture system in which their adaxial epidermal cells were spontaneously induced to trans-differentiate to transfer cells. During deposition of wall ingrowth papillae, the aligned cortical microtubule arrays in precursor epidermal cells were reorganized into a randomized array characterized by circular depletion zones. Concurrence of the temporal appearance, spatial pattern, and size of depletion zones and wall ingrowth papillae was consistent with each papilla occupying a depletion zone. Surprisingly, microtubules appeared not to regulate construction of wall ingrowth papillae, as neither depolymerization nor stabilization of cortical microtubules changed their deposition pattern or morphology. Moreover, the size and spatial pattern of depletion zones was unaltered when the formation of wall ingrowth papillae was blocked by inhibiting cellulose biosynthesis. In contrast, the depletion zones were absent when the cytosolic calcium plumes, responsible for directing wall ingrowth papillae formation, were blocked or dissipated. Thus, we conclude that the depletion zones within the cortical microtubule array result from localized depolymerization of microtubules initiated by elevated cytosolic Ca2+ levels at loci where wall ingrowth papillae are deposited. The physiological significance of the depletion zones as a mechanism to accommodate the construction of wall ingrowth papillae without compromising maintenance of the plasma membrane–microtubule inter-relationship is discussed. PMID:26136268

Plasma-polymerized SiOx deposition on polymer film surfaces for preparation of oxygen gas barrier polymeric films

International Nuclear Information System (INIS)

Inagaki, N.

2003-01-01

SiOx films were deposited on surfaces of three polymeric films, PET, PP, and Nylon; and their oxygen gas barrier properties were evaluated. To mitigate discrepancies between the deposited SiOx and polymer film, surface modification of polymer films was done, and how the surface modification could contribute to was discussed from the viewpoint of apparent activation energy for the permeation process. The SiOx deposition on the polymer film surfaces led to a large decrease in the oxygen permeation rate. Modification of polymer film surfaces by mans of the TMOS or Si-COOH coupling treatment in prior to the SiOx deposition was effective in decreasing the oxygen permeation rate. The cavity model is proposed as an oxygen permeation process through the SiOx-deposited Nylon film. From the proposed model, controlling the interface between the deposited SiOx film and the polymer film is emphasized to be a key factor to prepare SiOx-deposited polymer films with good oxygen gas barrier properties. (author)

Stable isotope, chemical, and mineral compositions of the Middle Proterozoic Lijiaying Mn deposit, Shaanxi Province, China

Science.gov (United States)

Yeh, Hsueh-Wen; Hein, James R.; Ye, Jie; Fan, Delian

1999-01-01

The Lijiaying Mn deposit, located about 250 km southwest of Xian, is a high-quality ore characterized by low P and Fe contents and a mean Mn content of about 23%. The ore deposit occurs in shallow-water marine sedimentary rocks of probable Middle Proterozoic age. Carbonate minerals in the ore deposit include kutnahorite, calcite, Mn calcite, and Mg calcite. Carbon (−0.4 to −4.0‰) and oxygen (−3.7 to −12.9‰) isotopes show that, with a few exceptions, those carbonate minerals are not pristine low-temperature marine precipitates. All samples are depleted in rare earth elements (REEs) relative to shale and have negative Eu and positive Ce anomalies on chondrite-normalized plots. The Fe/Mn ratios of representative ore samples range from about 0.034 to deep ocean-floor during the Cenozoic. Because the Lijiaying precursor mineral formed in a shallow-water marine environment, the atmospheric oxygen content during the Middle Proterozoic may have been lower than it has been during the Cenozoic.

Anoxic environments and oil source bed genesis

Energy Technology Data Exchange (ETDEWEB)

Demaison, G J [Chevron Overseas Petroleum Inc., San Francisco, CA; Moore, G T

1980-01-01

The anoxic, aquatic, environment is a mass of water so depleted in oxygen that virtually all aerobic biological activity has ceased. Anoxic conditions occur where the demand for oxygen in the water column exceeds the supply. The specific cause for preferential lipid enrichment probably relates to the biochemistry of anaerobic bacterial activity. Recent evidence suggests that ancient organic-rich sediments containing hydrogen-rich kerogens (potential oil source beds) were deposited in similar anoxic environments. We propose the following classification for modern aquatic anoxic settings: (1) Large anoxic lakes - Permanent stratification promotes development of anoxic bottom water, particularly in large, deep lakes, which are not subject to seasonal overturn, e.g., Lake Tanganyika. (2) Anoxic silled basins - Landlocked silled basins with positive water balance tend to become anoxic. Typical are the Baltic and Black Seas. In arid region seas (Red and Mediterranean Seas), evaporation exceeds river inflow, causing negative water balance and well-aerated, nutrient-depleted bottom waters. (3) Anoxic layers caused by upwelling - Develop only when the oxygen supply in deep water cannot match demand by decaying organisms. Examples are the Benguela current and Peru coastal upwelling. (4) Open ocean anoxic layers - Found at intermediate depths in the northeastern Pacific and northern Indian Oceans; due to distance from deep, oxygenated polar water sources. Analogous to world-wide anoxic events at times of global climatic warm-ups and major transgressions, as in late Jurassic and middle Cretaceous time. Petroleum exploration can be greatly assisted by using geochemistry to identify paleo-anoxic events in the stratigraphic record. Recognition of the proposed anoxic models in ancient sedimentary basins should help in regional mapping of oil shales and oil-source beds. 17 figures.

Calcium-dependent depletion zones in the cortical microtubule array coincide with sites of, but do not regulate, wall ingrowth papillae deposition in epidermal transfer cells.

Science.gov (United States)

Zhang, Hui-ming; Talbot, Mark J; McCurdy, David W; Patrick, John W; Offler, Christina E

2015-09-01

Trans-differentiation to a transfer-cell morphology is characterized by the localized deposition of wall ingrowth papillae that protrude into the cytosol. Whether the cortical microtubule array directs wall ingrowth papillae formation was investigated using a Vicia faba cotyledon culture system in which their adaxial epidermal cells were spontaneously induced to trans-differentiate to transfer cells. During deposition of wall ingrowth papillae, the aligned cortical microtubule arrays in precursor epidermal cells were reorganized into a randomized array characterized by circular depletion zones. Concurrence of the temporal appearance, spatial pattern, and size of depletion zones and wall ingrowth papillae was consistent with each papilla occupying a depletion zone. Surprisingly, microtubules appeared not to regulate construction of wall ingrowth papillae, as neither depolymerization nor stabilization of cortical microtubules changed their deposition pattern or morphology. Moreover, the size and spatial pattern of depletion zones was unaltered when the formation of wall ingrowth papillae was blocked by inhibiting cellulose biosynthesis. In contrast, the depletion zones were absent when the cytosolic calcium plumes, responsible for directing wall ingrowth papillae formation, were blocked or dissipated. Thus, we conclude that the depletion zones within the cortical microtubule array result from localized depolymerization of microtubules initiated by elevated cytosolic Ca(2+) levels at loci where wall ingrowth papillae are deposited. The physiological significance of the depletion zones as a mechanism to accommodate the construction of wall ingrowth papillae without compromising maintenance of the plasma membrane-microtubule inter-relationship is discussed. © The Author 2015. Published by Oxford University Press on behalf of the Society for Experimental Biology.

Dynamics of oxygen depletion in the nearshore of a coastal embayment of the southern Benguela upwelling system

CSIR Research Space (South Africa)

Pitcher, GC

2014-04-01

Full Text Available is characterized by seasonally recurrent hypoxia (<1.42 ml l(sup-1)) associated with a deep pool of oxygen-depleted water and episodic anoxia (<0.02 ml l(sup-1)) driven by the nearshore (<20 m isobath) decay of red tide. Coastal wind forcing influences DO...

Contribution of offshore petroleum deposits to marine food chain

Science.gov (United States)

Mori, S.

2009-12-01

Petroleum production out of offshore petroleum deposits often coincides with abundant fisheries in the world. Superposition of marine microorganism concentration distribution and offshore petroleum field distribution from various data in the literature provides to prove this coincidence. Sakhalin Island coastal regions, North Sea, Gulf of Mexico, etc. are chosen for the superpositions. Significant conformity is observed between the plankton concentration distribution and the offshore petroleum deposit distribution in all those regions. Also, most studies on the consequence of oil spills to marine eco-systems have focused mainly on hazardous marine pollution caused by spilled petroleum at high concentration in marine environment. However, some of those data clearly indicate stimulation of plankton population in properly low concentration levels of dissolved hydrocarbons and dissolved petroleum compositions. Further, increase of hydrocarbon concentration leads to its inhibition from its stimulation conditions upon crossing over a critical concentration level—a plankton stimulation/inhibition threshold concentration (SITC) of hydrocarbons. The SITC varies depending on hydrocarbon compounds, petroleum compositions, and microorganisms such as planktons. Further, petroleum composition diffusing through subterranean layers from petroleum deposits reacts with dissolved oxygen to be consumed at the ocean floor to precipitate the agglomerate suspension of hydrocarbons, leaving the sea water in a condition of oxygen depletion on the ocean floor. Such incidents are also briefly discussed.Plankton stimulation/inhibition threshold concentration of petroleum fractions

Defects, stoichiometry, and electronic transport in SrTiO{sub 3-δ} epilayers: A high pressure oxygen sputter deposition study

Energy Technology Data Exchange (ETDEWEB)

Ambwani, P.; Xu, P.; Jeong, J. S.; Deng, R.; Mkhoyan, K. A.; Jalan, B.; Leighton, C., E-mail: leighton@umn.edu [Department of Chemical Engineering and Materials Science, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Haugstad, G. [Characterization Facility, University of Minnesota, Minneapolis, Minnesota 55455 (United States)

2016-08-07

SrTiO{sub 3} is not only of enduring interest due to its unique dielectric, structural, and lattice dynamical properties, but is also the archetypal perovskite oxide semiconductor and a foundational material in oxide heterostructures and electronics. This has naturally focused attention on growth, stoichiometry, and defects in SrTiO{sub 3}, one exciting recent development being such precisely stoichiometric defect-managed thin films that electron mobilities have finally exceeded bulk crystals. This has been achieved only by molecular beam epitaxy, however (and to a somewhat lesser extent pulsed laser deposition (PLD)), and numerous open questions remain. Here, we present a study of the stoichiometry, defects, and structure in SrTiO{sub 3} synthesized by a different method, high pressure oxygen sputtering, relating the results to electronic transport. We find that this form of sputter deposition is also capable of homoepitaxy of precisely stoichiometric SrTiO{sub 3}, but only provided that substrate and target preparation, temperature, pressure, and deposition rate are carefully controlled. Even under these conditions, oxygen-vacancy-doped heteroepitaxial SrTiO{sub 3} films are found to have carrier density, mobility, and conductivity significantly lower than bulk. While surface depletion plays a role, it is argued from particle-induced X-ray emission (PIXE) measurements of trace impurities in commercial sputtering targets that this is also due to deep acceptors such as Fe at 100's of parts-per-million levels. Comparisons of PIXE from SrTiO{sub 3} crystals and polycrystalline targets are shown to be of general interest, with clear implications for sputter and PLD deposition of this important material.

Oxygen isotope mapping and evaluation of paleo-hydrothermal systems associated with synvolcanic intrusion and VMS deposits

International Nuclear Information System (INIS)

Taylor, B.E

2001-01-01

Whole-rock oxygen isotope mapping provides a useful method for the delineation and quantitative evaluation of paleo-hydrothermal systems associated with syn-volcanic intrusions and volcanic-associated massive sulfide (VMS) deposits. During the course of a four-year study of regional alteration systems associated with VMS Deposits, four syn-volcanic intrusive complexes in Canada were mapped using stable isotope techniques. The complexes included Noranda, Quebec; Clifford-Ben Nevis, Ontario; Snow Lake, Manitoba, and Sturgeon Lake, Ontario. This study was regional in extent, involving large areas and large numbers of whole-rock samples: Noranda (625 km 2 ;≥600 samples, plus others (total = 1198); Sturgeon Lake (525 km 2 ; 452 samples); Clifford-Ben Nevis (160 km 2 ; 251 samples); and Snow Lake (84 km 2 ; 575 samples). Isotopic data on whole-rock carbonates and hydrous minerals were also collected. The regional isotopic studies were carried out in concert with other studies on mineral assemblages and mineral composition, and on associated intrusive and extrusive rocks. The Clifford-Ben Nevis area was selected as a control area, in as much as it contains no known VMS deposits; all other areas are well-known, productive VMS districts. Oxygen isotope maps are, in a sense, thermal maps, illustrating the paleo-distribution of heat and fluids, and offering a potential aid to exploration. The isotopic data may be contoured to reveal zones of 18 O depletion and enrichment, relative to unaltered rocks. Zones of δ 18 O≤60% comprise rocks that have reacted with seawater at high (e.g., 300+ o C) temperatures. The volume of foot-wall rocks isotopically-depleted by water/rock interaction during the life of one or more episodes of submarine hydrothermal activity is proportional to the amount of heat available from the syn-volcanic intrusive center. These altered rocks comprise the reaction zone often inferred to have supplied metals and other constituents for the VMS deposits

Is depleted uranium a threat to health and the environment?

International Nuclear Information System (INIS)

2002-01-01

This issue has come to the fore in recent years now that Norwegian military personnel have been sent to regions of the world where ammunition made of depleted uranium has been used. A number of surveys have been conducted in the Balkans, so far indicating no health hazards to people present in these areas. However, the latest international surveys show that contamination may be long-lasting. Tonje Sekse represented the Norwegian Radiation Protection Authority at the United Nations Environment Programme's (UNEP) inspection tour to Serbia and Montenegro in the autumn of 2001. The report, entitled ''Depleted uranium in Serbia and Montenegro - Post-Conflict Environmental Assessment in the Federal Republic of Yugoslavia'' was published by UNEP in March 2002.(author)

Hyperbaric Oxygen Environment Can Enhance Brain Activity and Multitasking Performance

Directory of Open Access Journals (Sweden)

Dor Vadas

2017-09-01

Full Text Available Background: The Brain uses 20% of the total oxygen supply consumed by the entire body. Even though, <10% of the brain is active at any given time, it utilizes almost all the oxygen delivered. In order to perform complex tasks or more than one task (multitasking, the oxygen supply is shifted from one brain region to another, via blood perfusion modulation. The aim of the present study was to evaluate whether a hyperbaric oxygen (HBO environment, with increased oxygen supply to the brain, will enhance the performance of complex and/or multiple activities.Methods: A prospective, double-blind randomized control, crossover trial including 22 healthy volunteers. Participants were asked to perform a cognitive task, a motor task and a simultaneous cognitive-motor task (multitasking. Participants were randomized to perform the tasks in two environments: (a normobaric air (1 ATA 21% oxygen (b HBO (2 ATA 100% oxygen. Two weeks later participants were crossed to the alternative environment. Blinding of the normobaric environment was achieved in the same chamber with masks on while hyperbaric sensation was simulated by increasing pressure in the first minute and gradually decreasing to normobaric environment prior to tasks performance.Results: Compared to the performance at normobaric conditions, both cognitive and motor single tasks scores were significantly enhanced by HBO environment (p < 0.001 for both. Multitasking performance was also significantly enhanced in HBO environment (p = 0.006 for the cognitive part and p = 0.02 for the motor part.Conclusions: The improvement in performance of both single and multi-tasking while in an HBO environment supports the hypothesis which according to, oxygen is indeed a rate limiting factor for brain activity. Hyperbaric oxygenation can serve as an environment for brain performance. Further studies are needed to evaluate the optimal oxygen levels for maximal brain performance.

Hyperbaric Oxygen Environment Can Enhance Brain Activity and Multitasking Performance.

Science.gov (United States)

Vadas, Dor; Kalichman, Leonid; Hadanny, Amir; Efrati, Shai

2017-01-01

Background: The Brain uses 20% of the total oxygen supply consumed by the entire body. Even though, multitasking), the oxygen supply is shifted from one brain region to another, via blood perfusion modulation. The aim of the present study was to evaluate whether a hyperbaric oxygen (HBO) environment, with increased oxygen supply to the brain, will enhance the performance of complex and/or multiple activities. Methods: A prospective, double-blind randomized control, crossover trial including 22 healthy volunteers. Participants were asked to perform a cognitive task, a motor task and a simultaneous cognitive-motor task (multitasking). Participants were randomized to perform the tasks in two environments: (a) normobaric air (1 ATA 21% oxygen) (b) HBO (2 ATA 100% oxygen). Two weeks later participants were crossed to the alternative environment. Blinding of the normobaric environment was achieved in the same chamber with masks on while hyperbaric sensation was simulated by increasing pressure in the first minute and gradually decreasing to normobaric environment prior to tasks performance. Results: Compared to the performance at normobaric conditions, both cognitive and motor single tasks scores were significantly enhanced by HBO environment ( p Multitasking performance was also significantly enhanced in HBO environment ( p = 0.006 for the cognitive part and p = 0.02 for the motor part). Conclusions: The improvement in performance of both single and multi-tasking while in an HBO environment supports the hypothesis which according to, oxygen is indeed a rate limiting factor for brain activity. Hyperbaric oxygenation can serve as an environment for brain performance. Further studies are needed to evaluate the optimal oxygen levels for maximal brain performance.

26 CFR 1.611-1 - Allowance of deduction for depletion.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 7 2010-04-01 2010-04-01 true Allowance of deduction for depletion. 1.611-1... depletion. (a) Depletion of mines, oil and gas wells, other natural deposits, and timber—(1) In general... mines, oil and gas wells, other natural deposits, and timber, a reasonable allowance for depletion. In...

Studies on oxygen depletion and the toxic effect of sediments; Untersuchungen zur Sauerstoffzehrung und toxischen Wirkung von Sedimenten

Energy Technology Data Exchange (ETDEWEB)

Pfitzner, S.; Giest, B.; Wotzka, J. [Bundesanstalt fuer Gewaesserkunde, Berlin (Germany)

2000-11-01

Depending on their composition and how they were formed, water sediments contain varying amounts of oxygen-depleting substances. Their portion is particularly high in fine sediment and sediments formed in conjunction with exposure to a high level of wastewater. Particularly in current-free areas like old arms, indentations, sluices and outer ports, sediment forms with a high fine grain content and a correspondingly higher potential for depletion. If, for instance, the sediments are moved and stirred up during dredging, this may impair their oxygen content since oxygen consumption is far higher in a suspended sediment than when it is undisturbed on the water bottom. The very rapid spontaneous chemical oxidation and biological oxidation of reduced substances are possible oxygen-consuming processes. (orig.) [German] Gewaessersedimente enthalten in Abhaengigkeit von ihrer Zusammensetzung und der Art ihrer Entstehung unterschiedliche Mengen an Sauerstoff zehrenden Substanzen. Ihr Anteil ist besonders hoch in Feinsedimenten und solchen, die sich unter starkem Abwassereinfluss bilden konnten. Insbesondere in stroemungsberuhigten Gebieten, wie Altarmen, Ausbuchtungen sowie Schleusen und deren Vorhaefen, reichern sich Sedimente mit hohem Feinkornanteil und dementsprechend hoher potenzieller Zehrungsfaehigkeit an. Werden die Sedimente beispielsweise durch Baggermassnahmen bewegt und aufgewirbelt, kann es zur Beeintraechtigung des Sauerstoffhaushaltes kommen, da der Sauerstoffverbrauch eines Sedimentes bei Suspension um ein Vielfaches hoeher als bei ungestoerter Lagerung am Gewaesserboden sein kann. Als Sauerstoff verbrauchende Prozesse kommen die sehr schnell verlaufende spontane chemische Oxidation sowie die biologische Oxidation reduzierter Substanzen in Betracht. (orig.)

Properties of thin films deposited from HMDSO/O2 induced remote plasma: Effect of oxygen fraction

International Nuclear Information System (INIS)

Saloum, S.; Naddaf, M.; Al-Khaled, B.

2008-01-01

Thin films deposited from hexamethyle disiloxane (HMDSO)/O 2 mixture excited in a radio-frequency hollow cathode discharge system have been investigated for their structural, optical and corrosive properties as a function of oxygen fraction χo 2 (χo 2 =0, 0.38, 0.61, 0.76 and 0.90). It is found that the effect of oxygen fraction on films properties is related to O 2 dissociation degree (αd) behavior in pure oxygen plasma. αd has been investigated by actinometry optical emission spectroscopy (AOES) combined with double langmuir probe measurements, a maximum of O 2 dissociation degree of 15% has been obtained for 50 sccm flow rate of O 2 (χo 2 =0.61 in HMDSO/O 2 plasma). Fourier transform infrared spectroscopy (FTIR) and optical measurements showed that the behavior of both identified IR group densities and deposition rate as a function of oxygen fraction is similar to that of O 2 dissociation degree. The inorganic nature of the films depends significantly on oxygen fraction, the best inorganic structure of deposited films has been obtained for 62% HMDSO content in the mixture HMDSO/O 2 (χo 2 =0.38). The refractive index for deposited films from pure HMDSO(χo 2 =0) has been found to be higher than that of films deposited from HMDSO/O 2 mixture. In HMDSO/O 2 plasma, it has a behavior similar to that of deposition rate, and it is comparable to that of quartz. The effect of oxygen fraction on the corrosive properties of thin films deposited on steel has been investigated. It is found that the measured corrosion current density in 0.1 M KCI solution decreases with the addition of O 2 to HMDSO plasma, and it is minimum for χo 2 =0.38. (author)

A Review of Protist Grazing Below the Photic Zone Emphasizing Studies of Oxygen-Depleted Water Columns and Recent Applications of In situ Approaches

Directory of Open Access Journals (Sweden)

Virginia P. Edgcomb

2017-04-01

Full Text Available Little is still known of the impacts of protist grazing on bacterioplankton communities in the dark ocean. Furthermore, the accuracy of assessments of in situ microbial activities, including protist grazing, can be affected by sampling artifacts introduced during sample retrieval and downstream manipulations. Potential artifacts may be increased when working with deep-sea samples or samples from chemically unique water columns such as oxygen minimum zones (OMZs. OMZs are oxygen-depleted regions in the ocean, where oxygen concentrations can drop to <20 μM. These regions are typically located near eastern boundary upwelling systems and currently occur in waters occupying below about 8% of total ocean surface area, representing ~1% of the ocean's volume. OMZs have a profound impact not only on the distribution of marine Metazoa, but also on the composition and activities of microbial communities at the base of marine food webs. Here we present an overview of current knowledge of protist phagotrophy below the photic zone, emphasizing studies of oxygen-depleted waters and presenting results of the first attempt to implement new technology for conducting these incubation studies completely in situ (the Microbial Sampling- Submersible Incubation Device, MS-SID. We performed 24-h incubation experiments in the Eastern Tropical South Pacific (ETSP OMZ. This preliminary study shows that up to 28% of bacterial biomass may be consumed by protists in waters where oxygen concentrations were down to ~4.8 μM and up to 13% at a station with nitrite accumulation where oxygen concentrations were undetectable. Results also show that shipboard measurements of grazing rates were lower than rates measured from the same water using the MS-SID, suggesting that in situ experiments help to minimize artifacts that may be introduced when conducting incubation studies using waters collected from below the photic zone, particularly from oxygen-depleted regions of the water

Oxygen depletion of bismuth molybdates

Energy Technology Data Exchange (ETDEWEB)

Yong, L.K.; Howe, R.F.; Keulks, G.W.; Hall, W.K.

1978-05-01

Pure ..cap alpha..-phase bismuth molybdate (Bi/sub 2/Mo/sub 3/O/sub 12/), which is known to be weakly active for selective oxidation, and pure ..gamma..-phase bismuth molybdate (Bi/sub 2/MoO/sub 6/), which has good activity, were subjected to oxidation-reduction cycles with known amounts of hydrogen and oxygen, at 300/sup 0/-570/sup 0/C and with evacuation steps between treatments. The volume of oxygen consumed during reoxidation was equal to half the hydrogen consumed during the reduction on the ..cap alpha..-phase, which indicated that no hydrogen was retained during reduction. For the ..gamma..-phase, the oxygen consumption was greater than half of the hydrogen consumption and it increased with extent of reduction. The excess oxygen was apparently consumed by filling anion vacancies formed during outgassing subsequent to the reduction step. ESR spectroscopy and temperature-programed oxidation-reduction indicated that lattice oxide ions which bridge between bismuth and molybdenum layers of the koechlinite structure become more labile when the catalyst is in a partially reduced state, and that this effect is greater in the ..gamma..- than the ..cap alpha..-phase. Table and 15 references.

Carbon-oxygen isotopes and rare earth elements as an exploration vector for Carlin-type gold deposits: A case study of the Shuiyindong gold deposit, Guizhou Province, SW China

Science.gov (United States)

Tan, Qin-Ping; Xia, Yong; Wang, Xueqiu; Xie, Zhuo-Jun; Wei, Dong-Tian

2017-10-01

The Shuiyindong gold deposit is a deeply concealed strata-bound Carlin-type deposit in southwestern Guizhou Province, China. The deposit lies on the eastern limb of the Huijiabao anticline with ores mainly along the anticline axis and hosted in bioclastic limestone, containing calcite veins, of the Permian Longtan Formation units. In this study, we measured carbon and oxygen isotopic ratios and rare earth element (REE) concentrations of the host rocks and calcite veins along a profile across the Shuiyindong deposit. Orebodies in the upper unit of the Longtan Formation have higher δ18O values (20.6-22.4‰) and lower δ13C values (-3.7 to -0.5‰) than the country rocks (δ18O: 18.8-21.4‰; δ13C: -0.7 to 0.8‰). However, there are no obvious trends of δ18O and δ13C values from the country rocks to the orebodies in the middle unit of the Longtan Formation. The spatial distribution of the calcite veins displays distinct halos of δ13C and δ18O values and REE concentrations. Calcite veins along the anticlinal axis and major reverse fault are enriched in Middle REE (Sm, Eu, Gd, and Tb) and 18O and depleted in 13C. Surficial veining calcite-filled fractures/faults that connect to deep concealed strata-bound gold mineralization systems can be vectors toward deep ores in southwestern Guizhou Province, China.

Low temperature (< 100 °C) deposited P-type cuprous oxide thin films: Importance of controlled oxygen and deposition energy

International Nuclear Information System (INIS)

Li, Flora M.; Waddingham, Rob; Milne, William I.; Flewitt, Andrew J.; Speakman, Stuart; Dutson, James; Wakeham, Steve; Thwaites, Mike

2011-01-01

With the emergence of transparent electronics, there has been considerable advancement in n-type transparent semiconducting oxide (TSO) materials, such as ZnO, InGaZnO, and InSnO. Comparatively, the availability of p-type TSO materials is more scarce and the available materials are less mature. The development of p-type semiconductors is one of the key technologies needed to push transparent electronics and systems to the next frontier, particularly for implementing p–n junctions for solar cells and p-type transistors for complementary logic/circuits applications. Cuprous oxide (Cu 2 O) is one of the most promising candidates for p-type TSO materials. This paper reports the deposition of Cu 2 O thin films without substrate heating using a high deposition rate reactive sputtering technique, called high target utilisation sputtering (HiTUS). This technique allows independent control of the remote plasma density and the ion energy, thus providing finer control of the film properties and microstructure as well as reducing film stress. The effect of deposition parameters, including oxygen flow rate, plasma power and target power, on the properties of Cu 2 O films are reported. It is known from previously published work that the formation of pure Cu 2 O film is often difficult, due to the more ready formation or co-formation of cupric oxide (CuO). From our investigation, we established two key concurrent criteria needed for attaining Cu 2 O thin films (as opposed to CuO or mixed phase CuO/Cu 2 O films). First, the oxygen flow rate must be kept low to avoid over-oxidation of Cu 2 O to CuO and to ensure a non-oxidised/non-poisoned metallic copper target in the reactive sputtering environment. Secondly, the energy of the sputtered copper species must be kept low as higher reaction energy tends to favour the formation of CuO. The unique design of the HiTUS system enables the provision of a high density of low energy sputtered copper radicals/ions, and when combined with a

High-rate deposition of photocatalytic TiO2 films by oxygen plasma assist reactive evaporation method

International Nuclear Information System (INIS)

Sakai, Tetsuya; Kuniyoshi, Yuji; Aoki, Wataru; Ezoe, Sho; Endo, Tatsuya; Hoshi, Yoichi

2008-01-01

High-rate deposition of titanium dioxide (TiO 2 ) film was attempted using oxygen plasma assisted reactive evaporation (OPARE) method. Photocatalytic properties of the film were investigated. During the deposition, the substrate temperature was fixed at 400 deg. C. The film deposition rate can be increased by increasing the supply of titanium atoms to the substrate, although oversupply of the titanium atoms causes oxygen deficiency in the films, which limits the deposition rate. The film structure depends strongly on the supply ratio of oxygen molecules to titanium atoms O 2 /Ti and changes from anatase to rutile structure as the O 2 /Ti supply ratio increased. Consequently, the maximum deposition rates of 77.0 nm min -1 and 145.0 nm min -1 were obtained, respectively, for the anatase and rutile film. Both films deposited at such high rates showed excellent hydrophilicity and organic decomposition performance. Even the film with rutile structure deposited at 145.0 nm min -1 had a contact angle of less than 2.5 deg. by UV irradiation for 5.0 h and an organics-decomposition performance index of 8.9 [μmol l -1 min -1 ] for methylene blue

Oxygen isotope zonation at the Golden Cross low-sulfidation epithermal gold deposit, New Zealand

International Nuclear Information System (INIS)

Mauk, J.L.; Simpson, M.P.

2001-01-01

Forty-one whole rock samples from the Gold Cross low-sulfidation epithermal Au-Ag deposit have δ 18 O values that range from 4.4 to 9.3 per mil, with an average value of 7.0 per mil. Unaltered and weakly altered rocks have δ 18 O values greater than 8 per mil, and the orebody is surrounded by samples that are depleted in 18 O. A strongly silicified sample adjacent to the Empire Vein System has a δ 18 O value of 9.0 per mil, similar to previously reported analyses of vein quartz (7.0 to 11.7 per mil, average 9.4 per mil). This suggests that, in detail, Golden Cross may have a zone of 18 O-enriched wall rocks in the core of the deposit, adjacent to the main underground veins. Although some workers have suggested that stable isotope geochemistry may provide useful information for epithermal mineral deposit exploration, at Golden Cross this is not the case. Alteration minerals, major elements and trace elements all define larger, less ambiguous halos than the zone of 18 O-depleted wall rocks. (author). 21 refs., 3 figs., 1 tab

Influence of reactive oxygen species during deposition of iron oxide films by high power impulse magnetron sputtering

Science.gov (United States)

Stranak, V.; Hubicka, Z.; Cada, M.; Bogdanowicz, R.; Wulff, H.; Helm, C. A.; Hippler, R.

2018-03-01

Iron oxide films were deposited using high power impulse magnetron sputtering (HiPIMS) of an iron cathode in an argon/oxygen gas mixture at different gas pressures (0.5 Pa, 1.5 Pa, and 5.0 Pa). The HiPIMS system was operated at a repetition frequency f  =  100 Hz with a duty cycle of 1%. A main goal is a comparison of film growth during conventional and electron cyclotron wave resonance-assisted HiPIMS. The deposition plasma was investigated by means of optical emission spectroscopy and energy-resolved mass spectrometry. Active oxygen species were detected and their kinetic energy was found to depend on the gas pressure. Deposited films were characterized by means of spectroscopic ellipsometry and grazing incidence x-ray diffraction. Optical properties and crystallinity of as-deposited films were found to depend on the deposition conditions. Deposition of hematite iron oxide films with the HiPIMS-ECWR discharge is attributed to the enhanced production of reactive oxygen species.

Recent oxygen depletion and benthic faunal change in shallow areas of Sannäs Fjord, Swedish west coast

Science.gov (United States)

Nordberg, Kjell; Polovodova Asteman, Irina; Gallagher, Timothy M.; Robijn, Ardo

2017-09-01

Sannäs Fjord is a shallow fjord (European Union. Yet, observations during the summers of 2008-2011 show that the shallow inner fjord inlet experiences severe oxygen depletion at 5-12 m water depth. To explore if the oxygen depletion is only a recent phenomenon and to evaluate the potential of fjord sediments to archive such environmental changes, in 2008 and 2009 seven sediment cores were taken along a transect oriented lengthwise in the fjord. The cores were analysed for organic carbon, C/N, benthic foraminifera and lead pollution records (as relative age marker). Carbon content increases in most of the cores since the 1970-80s, while C/N ratio decreases from the core base upward since 1995. Foraminiferal assemblages in most core stratigraphies are dominated by agglutinated species. Calcareous species (mainly elphidiids) have become dominant in the upper part of the records since the late 1990s or 2000 (the inner fjord and the deepest basin) and since the 1950-70s (the outer fjord). In the inner Sannäs Fjord, an increase of agglutinated foraminiferal species (e.g. Eggerelloides scaber) and organic inner linings occurred since the 1970s, suggesting an intensification of taphonomic processes affecting postmortem calcareous shell preservation. A study of living vs. dead foraminiferal assemblages undertaken during June-August 2013 demonstrates that in the shallow inner fjord, strong carbonate dissolution occurs within 1-3 months following the foraminiferal growth. The dissolution is linked to corrosive conditions present within the sediment - bottom water interface, and is likely caused by the organic matter decay, resulting in severe hypoxia to anoxia. Oxygen depletion at < 10 m w.d. develops fast due to the small water volume and limited bottom water exchange caused by a close proximity of pycnocline to the fjord bottom. Sediment cores from the deep fjord basin and the outer fjord are, on the contrary, characterized by good to excellent preservation of

NEBULAR WATER DEPLETION AS THE CAUSE OF JUPITER'S LOW OXYGEN ABUNDANCE

Energy Technology Data Exchange (ETDEWEB)

Mousis, Olivier [Universite de Franche-Comte, Institut UTINAM, CNRS/INSU, UMR 6213, Observatoire des Sciences de l' Univers de Besancon (France); Lunine, Jonathan I. [Center for Radiophysics and Space Research, Space Sciences Building, Cornell University, Ithaca, NY 14853 (United States); Madhusudhan, Nikku [Yale Center for Astronomy and Astrophysics, Department of Physics, Yale University, New Haven, CT 06511 (United States); Johnson, Torrence V., E-mail: olivier.mousis@obs-besancon.fr [Jet Propulsion Laboratory, California Institute of Technology, 4800 Oak Grove Drive, Pasadena, CA 91109 (United States)

2012-05-20

Motivated by recent spectroscopic observations suggesting that atmospheres of some extrasolar giant planets are carbon-rich, i.e., carbon/oxygen ratio (C/O) {>=} 1, we find that the whole set of compositional data for Jupiter is consistent with the hypothesis that it should be a carbon-rich giant planet. We show that the formation of Jupiter in the cold outer part of an oxygen-depleted disk (C/O {approx} 1) reproduces the measured Jovian elemental abundances at least as well as the hitherto canonical model of Jupiter formed in a disk of solar composition (C/O 0.54). The resulting O abundance in Jupiter's envelope is then moderately enriched by a factor of {approx}2 Multiplication-Sign solar (instead of {approx}7 Multiplication-Sign solar) and is found to be consistent with values predicted by thermochemical models of the atmosphere. That Jupiter formed in a disk with C/O {approx} 1 implies that water ice was heterogeneously distributed over several AU beyond the snow line in the primordial nebula and that the fraction of water contained in icy planetesimals was a strong function of their formation location and time. The Jovian oxygen abundance to be measured by NASA's Juno mission en route to Jupiter will provide a direct and strict test of our predictions.

Effect of deposition temperature & oxygen pressure on mechanical properties of (0.5) BZT-(0.5)BCT ceramic thin films

Science.gov (United States)

Sailaja, P.; Kumar, N. Pavan; Rajalakshmi, R.; Kumar, R. Arockia; Ponpandian, N.; Prabahar, K.; Srinivas, A.

2018-05-01

Lead free ferroelectric thin films of {(0.5) BZT-(0.5) BCT} (termed as BCZT) were deposited on Pt/TiO2/SiO2/Si substrates by pulsed laser deposition at four deposition temperatures 600, 650, 700, 750°C and at two oxygen pressures viz. 75mtorr and 100 mtorr using BCZT ceramic target (prepared by solid state sintering method). The effect of deposition temperature and oxygen pressure on the structure, microstructure and mechanical properties of BCZT films were studied. X-ray diffraction patterns of deposited films confirm tetragonal crystal symmetry and the crystallinity of the films increases with increasing deposition temperature. Variation in BCZT grain growth was observed when the films are deposited at different temperatures andoxygen pressures respectively. The mechanical properties viz. hardness and elastic modulus were also found to be high with increase in the deposition temperature and oxygen pressure. The results will be discussed.

Proof-of-principle of high-fidelity coupled CRUD deposition and cycle depletion simulation

International Nuclear Information System (INIS)

Walter, Daniel J.; Kendrick, Brian K.; Petrov, Victor; Manera, Annalisa; Collins, Benjamin; Downar, Thomas

2015-01-01

A multiphysics framework for the high-fidelity simulation of CRUD deposition is developed to better understand the coupled physics and their respective feedback mechanisms. This framework includes the primary physics of lattice depletion, computational fluid dynamics, and CRUD chemistry. The three physics are coupled together via the operator-splitting technique, where predictor–corrector and fixed-point iteration schemes are utilized to converge the nonlinear solution. High-fidelity simulations may provide a means to predict and assess potential operating issues, including CRUD induced power shift and CRUD induced localized corrosion, known as CIPS and CILC, respectively. As a proof-of-principle, a coupled 500-day cycle depletion simulation of a pressurized water reactor fuel pin cell was performed using the coupled code suite; a burnup of 31 MWd/kgHM was reached. The simulation recreated the classic striped CRUD pattern often seen on pulled fuel rods containing CRUD. It is concluded that the striping is caused by the flow swirl induced by spacer grid mixing vanes. Two anti-correlated effects contribute to the striping: (1) the flow swirl yields significant azimuthal temperature variations, which impact the locations where CRUD deposits, and (2) the flow swirl is correlated to increased shear stress along the cladding surface and subsequent erosion of the CRUD layer. The CIPS condition of the core is concluded to be primarily controlled by lithium tetraborate precipitation, referred to as boron hideout, which occurs in regions experiencing subcooled nucleate boiling as soluble boron and lithium species reach their solubility limit within the CRUD layer. Subsequently, a localized reduction in power occurs due to the high neutron absorption cross section of boron-10

Depositional environment and provenance of Middle Siwalik ...

Indian Academy of Sciences (India)

The sedimentary facies and facies associations within the lithostratigraphic column of the Middle Siwalik rocks show temporal repetition of sedimentary facies associations suggesting oscillation between proximal-, mid- and distal fan setups within a palaeo-alluvial fan depositional environment similar to the depositional ...

Selective reduction of nitric oxide over Cu/ZSM-5: The role of oxygen in suppressing catalyst deactivation by carbonaceous deposits

Energy Technology Data Exchange (ETDEWEB)

d' Itri, Julie L; Sachtler, Wolfgang M.H. [V.N. Ipatieff Laboratory, Center for Catalysis and Surface Science, Departments of Chemical Engineering and Chemistry, Northwestern University, Evanston, IL (United States)

1993-06-15

The role of oxygen in the selective reduction of nitrogen monoxide by either propane or propene over 'excessively' ion-exchanged Cu/ZSM-5 has been studied. In a wide temperature region and in the absence of additives such as steam, propane is a more effective reductant than propene; with propane and in the presence of oxygen reduction of nitric oxide to nitrogen approaches 100% above 600 K. The difference in effectiveness is due to the different degree of catalyst deactivation by carbonaceous deposits: more carbonaceous material is deposited from propene than from propane. Temperature-programmed oxidation shows that above 600 K the rate of oxidation of carbonaceous deposits by oxygen is significant. The amount of such carbonaceous deposits is, therefore, lower when catalytic tests above 600 K are done in the presence of oxygen. At very high temperatures, the in situ volatilization of the deposits by reaction with oxygen keeps the catalyst surface clean in the steady state of nitric oxide reduction.

Facies and facies architecture and depositional environments of the ...

African Journals Online (AJOL)

Facies and facies architecture and depositional environments of the ... PROMOTING ACCESS TO AFRICAN RESEARCH ... Depositional environments of the Yolde Formation were studied based on the analysis of facies and facies architecture. ... Senegal (6); Sierra Leone (1); South Africa (96); South Sudan (1); Sudan (3) ...

Near-surface hydrogen depletion of diamond-like carbon films produced by direct ion deposition

Science.gov (United States)

Markwitz, Andreas; Gupta, Prasanth; Mohr, Berit; Hübner, René; Leveneur, Jerome; Zondervan, Albert; Becker, Hans-Werner

2016-03-01

Amorphous atomically flat diamond-like carbon (DLC) coatings were produced by direct ion deposition using a system based on a Penning ion source, butane precursor gas and post acceleration. Hydrogen depth profiles of the DLC coatings were measured with the 15N R-NRA method using the resonant nuclear reaction 1H(15N, αγ)12C (Eres = 6.385 MeV). The films produced at 3.0-10.5 kV acceleration voltage show two main effects. First, compared to average elemental composition of the film, the near-surface region is hydrogen depleted. The increase of the hydrogen concentration by 3% from the near-surface region towards the bulk is attributed to a growth model which favours the formation of sp2 hybridised carbon rich films in the film formation zone. Secondly, the depth at which the maximum hydrogen concentration is measured increases with acceleration voltage and is proportional to the penetration depth of protons produced by the ion source from the precursor gas. The observed effects are explained by a deposition process that takes into account the contributions of ion species, hydrogen effusion and preferential displacement of atoms during direct ion deposition.

Vitamin D Depletion in Pregnancy Decreases Survival Time, Oxygen Saturation, Lung Weight and Body Weight in Preterm Rat Offspring.

Directory of Open Access Journals (Sweden)

Sine Lykkedegn

Full Text Available Animal studies suggest a role of vitamin D in fetal lung development although not studied in preterm animals. We tested the hypothesis that vitamin D depletion aggravates respiratory insufficiency in preterm rat offspring. Furthermore, the effects of vitamin D depletion on growth and lung surfactant were investigated. Female Sprague-Dawley rats were randomly assigned low vitamin D (VDL or control diet before mating and followed with serum 25-hydroxyvitamin D (s-25(OHD determinations. After cesarean section at gestational day 19 (E19 or day 22 (E22, placental weight, birth weight, crown-rump-length (CRL, oxygenation (SaO2 at 30 min and survival time were recorded. The pup lungs were analyzed for phospholipid levels, surfactant protein A-D mRNA and the expression of the vitamin D receptor (VDR. S-25(OHD was significantly lower in the VDL group at cesarean section (12 vs. 30nmol/L, p<0.0001. Compared to the controls, E19 VDL pups had lower birth weight (2.13 vs. 2.29g, p<0.001, lung weight (0.09 vs. 0.10g, p = 0.002, SaO2 (54% vs. 69%, p = 0.002 as well as reduced survival time (0.50 vs. 1.25h, p<0.0001. At E22, the VDL-induced pulmonary differences were leveled out, but VDL pups had lower CRL (4.0 vs. 4.5cm, p<0.0001. The phospholipid levels and the surfactant protein mRNA expression did not differ between the dietary groups. In conclusion, Vitamin D depletion led to lower oxygenation and reduced survival time in the preterm offspring, associated with reduced lung weight and birth weight. Further studies of vitamin D depletion in respiratory insufficiency in preterm neonates are warranted.

LET calibration for CR-39 detectors in different oxygen environments

International Nuclear Information System (INIS)

Zhou, D.; Semones, E.; Weyland, M.; Benton, E.R.

2007-01-01

High LET (linear energy transfer) radiation is the main contributor to the radiation field in low Earth orbit (LEO) in terms of dose equivalent. CR-39 plastic nuclear track detectors (PNTDs) can measure the LET spectrum and charge spectrum for the complicated radiation field in space. Previous research indicated that the sensitivity of CR-39 is different for CR-39 PNTDs working in different oxygen environments. LET calibration for CR-39 detectors in different oxygen environments is needed. Almost all the previous LET calibration work was carried out for CR-39 detectors in good-oxygen condition, LET calibration work for CR-39 in poor-oxygen condition has not been conducted until our work. Systematic LET calibrations were carried out by JSC-SRAG (Space Radiation Analysis Group) for CR-39 detectors working in different oxygen environments and abundant results of LET calibrations were obtained. This paper introduces the method for CR-39 LET calibration, presents and discusses the calibration results and some applications

Anaerobic nitrogen turnover by sinking diatom aggregates at varying ambient oxygen levels

DEFF Research Database (Denmark)

Stief, Peter; Kamp, Anja; Thamdrup, Bo

2016-01-01

nitrate supply. Sinking diatom aggregates can contribute directly to fixed-nitrogen loss in low-oxygen environments in the ocean and vastly expand the ocean volume in which anaerobic nitrogen turnover is possible, despite relatively high ambient oxygen levels. Depending on the extent of intracellular......In the world’s oceans, even relatively low oxygen levels inhibit anaerobic nitrogen cycling by free-living microbes. Sinking organic aggregates, however, might provide oxygen-depleted microbial hotspots in otherwise oxygenated surface waters. Here, we show that sinking diatom aggregates can host...

The role of oxygen in the deposition of copper–calcium thin film as diffusion barrier for copper metallization

Energy Technology Data Exchange (ETDEWEB)

Yu, Zhinong, E-mail: znyu@bit.edu.cn [School of Optoelectronics and Beijing Engineering Research Center of Mixed Reality and Advanced Display, Beijing Institute of Technology, Beijing 100081 (China); Ren, Ruihuang [School of Optoelectronics and Beijing Engineering Research Center of Mixed Reality and Advanced Display, Beijing Institute of Technology, Beijing 100081 (China); Xue, Jianshe; Yao, Qi; Li, Zhengliang; Hui, Guanbao [Beijing BOE Optoelectronics Technology Co., Ltd, Beijing 100176 (China); Xue, Wei [School of Optoelectronics and Beijing Engineering Research Center of Mixed Reality and Advanced Display, Beijing Institute of Technology, Beijing 100081 (China)

2015-02-15

Highlights: • The CuCa film as the diffusion barrier of Cu film improves the adhesion of Cu film. • The introduction of oxygen into the deposition of CuCa film is necessary to improve the adhesion of Cu film. • The CuCa alloy barrier layer deposited at oxygen atmosphere has perfect anti-diffusion between Cu film and substrate. - Abstract: The properties of copper (Cu) metallization based on copper–calcium (CuCa) diffusion barrier as a function of oxygen flux in the CuCa film deposition were investigated in view of adhesion, diffusion and electronic properties. The CuCa film as the diffusion barrier of Cu film improves the adhesion of Cu film, however, and increases the resistance of Cu film. The introduction of oxygen into the deposition of CuCa film induces the improvement of adhesion and crystallinity of Cu film, but produces a slight increase of resistance. The increased resistance results from the partial oxidation of Cu film. The annealing process in vacuum further improves the adhesion, crystallinity and conductivity of Cu film. X-ray diffraction (XRD) and Auger electron spectroscopy (AES) show that the CuCa alloy barrier layer deposited at oxygen atmosphere has perfect anti-diffusion between Cu film and substrate due to the formation of Ca oxide in the interface of CuCa/substrate.

Early Cambrian oxygen minimum zone-like conditions at Chengjiang

DEFF Research Database (Denmark)

Hammarlund, Emma U.; Gaines, Robert R.; Prokopenko, Maria G.

2017-01-01

in early Cambrian marine settings and the relationship of those conditions to early metazoan ecosystems is still emerging. Here, we report multi-proxy geochemical data from two drill cores through the early Cambrian (Series 2) Yu’anshan Formation of Yunnan, China. Results reveal dynamic water...... oxygen-minimum zones. The oxygenated benthic environments in which the Chengjiang biota thrived were proximal to, but sharply separated from, the open ocean by a persistent anoxic water mass that occupied a portion of the outer shelf. Oxygen depletion in the lower water column developed dynamically...

Oxygen dynamics around buried lesser sandeels Ammodytes tobianus (Linnaeus 1785): mode of ventilation and oxygen requirements

DEFF Research Database (Denmark)

Behrens, Jane W; Stahl, Henrik J; Steffensen, John F

2007-01-01

The oxygen environment around buried sandeels (Ammodytes tobianus) was monitored by planar optodes. The oxygen penetration depth at the sediment interface was only a few mm. Thus fish, typically buried at 1-4 cm depth, were generally in anoxic sediment. However, they induced an advective transport...... down along the body, referred to as ;plume ventilation'. Yet, within approximately 30 min the oxic plume was replenished by oxygen-depleted water from the gills. The potential for cutaneous respiration by the buried fish was thus of no quantitative importance. Calculations derived by three independent...... methods (each with N=3) revealed that the oxygen uptake of sandeel buried for 6-7 h was 40-50% of previous estimates on resting respirometry of non-buried fish, indicating lower O(2) requirements during burial on a diurnal timescale. Buried fish exposed to decreasing oxygen tensions gradually approached...

Near-surface hydrogen depletion of diamond-like carbon films produced by direct ion deposition

Energy Technology Data Exchange (ETDEWEB)

Markwitz, Andreas, E-mail: A.Markwitz@gns.cri.nz [GNS Science, Lower Hutt (New Zealand); The MacDiarmid Institute for Advanced Materials and Nanotechnology (New Zealand); Gupta, Prasanth [GNS Science, Lower Hutt (New Zealand); The MacDiarmid Institute for Advanced Materials and Nanotechnology (New Zealand); Mohr, Berit [GNS Science, Lower Hutt (New Zealand); Hübner, René [Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden-Rossendorf (Germany); Leveneur, Jerome; Zondervan, Albert [GNS Science, Lower Hutt (New Zealand); Becker, Hans-Werner [RUBION, Ruhr-University Bochum (Germany)

2016-03-15

Amorphous atomically flat diamond-like carbon (DLC) coatings were produced by direct ion deposition using a system based on a Penning ion source, butane precursor gas and post acceleration. Hydrogen depth profiles of the DLC coatings were measured with the 15N R-NRA method using the resonant nuclear reaction {sup 1}H({sup 15}N, αγ){sup 12}C (E{sub res} = 6.385 MeV). The films produced at 3.0–10.5 kV acceleration voltage show two main effects. First, compared to average elemental composition of the film, the near-surface region is hydrogen depleted. The increase of the hydrogen concentration by 3% from the near-surface region towards the bulk is attributed to a growth model which favours the formation of sp{sup 2} hybridised carbon rich films in the film formation zone. Secondly, the depth at which the maximum hydrogen concentration is measured increases with acceleration voltage and is proportional to the penetration depth of protons produced by the ion source from the precursor gas. The observed effects are explained by a deposition process that takes into account the contributions of ion species, hydrogen effusion and preferential displacement of atoms during direct ion deposition.

Determination of Oxygen Production by Cyanobacteria in Desert Environment Soil

Science.gov (United States)

Bueno Prieto, J. E.

2009-12-01

The cyanobacteria have been characterized for being precursor in the production of oxygen. By means of photosynthetic reactions, they provide oxygen to the environment that surrounds them and they capture part of surrounding dioxide of carbon. This way it happened since the primitive Earth until today. Besides, these microorganisms can support the harmful effects of ultraviolet radiation. The presence of cyanobacterias in an environment like a dry tropical bioma, such as the geographical location called Desert of The Tatacoa (Huila - Colombia), is determinant to establish parameters in the search of biological origin of atmospheric oxygen detected in Mars. In that case, I work with a random sample of not rhizospheric soil, taken to 15 cm of depth. After determining the presence of cyanobacterias in the sample, this one was in laboratory to stimulate the oxygen production. The presence of oxygen in Mars is very interesting. Since oxygen gas is very reactive, it disappear if it is not renewed; the possibility that this renovation of oxygen has a biological origin is encouraging, bearing in mind that in a dry environment and high radiation such as the studied one, the production of oxygen by cyanobacterias is notable. Also it is necessary to keep in mind that the existence of cyanobacterias would determine water presence in Mars subsoil and the nutrients cycles renovation. An interesting exploration possibility for some future space probe to Mars might be the study of worldwide distribution of oxygen concentration in this planet and this way, indentify zones suitable for microbian life.

Effects of oxygen gas pressure on properties of iron oxide films grown by pulsed laser deposition

International Nuclear Information System (INIS)

Guo, Qixin; Shi, Wangzhou; Liu, Feng; Arita, Makoto; Ikoma, Yoshifumi; Saito, Katsuhiko; Tanaka, Tooru; Nishio, Mitsuhiro

2013-01-01

Highlights: ► Pulsed laser deposition is a promising technique for growing iron oxide films. ► Crystal structure of the iron oxide films strongly depends on oxygen gas pressure. ► Optimum of the oxygen gas pressure leads single phase magnetite films with high crystal quality. -- Abstract: Iron oxide films were grown on sapphire substrates by pulsed laser deposition at oxygen gas pressures between 1 × 10 −5 and 1 × 10 −1 Pa with a substrate temperature of 600 °C. Atomic force microscope, X-ray diffraction, Raman spectroscopy, X-ray absorption fine structure, and vibrational sample magnetometer analysis revealed that surface morphology and crystal structure of the iron oxide films strongly depend on the oxygen gas pressure during the growth and the optimum oxygen gas pressure range is very narrow around 1 × 10 −3 Pa for obtaining single phase magnetite films with high crystal quality

Effects of river morphology, hydraulic gradients, and sediment deposition on water exchange and oxygen dynamics in salmonid redds.

Science.gov (United States)

Schindler Wildhaber, Y; Michel, C; Epting, J; Wildhaber, R A; Huber, E; Huggenberger, P; Burkhardt-Holm, P; Alewell, C

2014-02-01

Fine sediment decreasing gravel permeability and oxygen supply to incubating salmonid embryos, is often considered the main contributing factor for the observed decline of salmonid populations. However, oxygen supply to salmonid embryos also depends on hydraulic conditions driving water flow through the redd. A more generalized perspective is needed to better understand the constraints on successful salmonid incubation in the many heavily modified fluvial ecosystems of the Northern Hemisphere. The effects of hydraulic gradients, riverbed and redd morphology as well as fine sediment deposition on dissolved oxygen (DO) and water exchange was studied in 18 artificial redds at three sites along a modified river. Fifty percent of the redds in the two downstream sites were lost during high flow events, while redd loss at the upstream site was substantially lower (8%). This pattern was likely related to increasing flood heights from up- to downstream. Specific water infiltration rates (q) and DO were highly dynamic and driven on multiple temporal and spatial scales. Temporally, the high permeability of the redd gravel and the typical pit-tail structure of the new built redds, leading to high DO, disappeared within a month, when fine sediment had infiltrated and the redd structure was leveled. On the scale of hours to days, DO concentrations and q increased during high flows, but decreased during the falling limb of the water level, most likely related to exfiltration of oxygen depleted groundwater or hyporheic water. DO concentrations also decreased under prolonged base flow conditions, when increased infiltration of silt and clay particles clogged the riverbed and reduced q. Spatially, artificial log steps affected fine sediment infiltration, q and interstitial DO in the redds. The results demonstrate that multiple factors have to be considered for successful river management in salmonid streams, including riverbed structure and local and regional hydrogeological

Full-scale measurements of smoke transport and deposition in ventilation system ductwork

International Nuclear Information System (INIS)

Martin, R.A.; Fenton, D.L.

1985-07-01

This study is part of an effort to obtain experimental data in support of the fire accident analysis computer code FIRAC, which was developed at the Los Alamos National Laboratory. FIRAC can predict the transient movement of aerosolized or gaseous material throughout the complex ventilation systems of nuclear fuel cycle facilities. We conducted a preliminary set of full-scale material depletion/modification experiments to help assess the accuracy of the code's aerosol depletion model. Such tests were performed under realistic conditions using real combustion products in full-sized ducts at typical airflow rates. To produce a combustion aerosol, we burned both polystyrene and polymethyl methacrylate, the most and least smoky fuels typically found in fuel cycle plants, under varied ventilation (oxygen-lean and oxygen-rich) conditions. Aerosol mass deposition, size, and concentration measurements were performed. We found that as much as approx.25% of polystyrene smoke mass and as little as 2% of the polymethyl methacrylate generated at the entrance to a 15.2-m duct is deposited on the duct walls. We also compared our experimental results with theoretical equations currently used in FIRAC. 28 refs., 8 figs., 5 tabs

Oligocene Fluvio-Deltaic Depositional Environments Salin Sub-Basin, Central Myanmar

Science.gov (United States)

Gough, A.; Hall, R.

2017-12-01

A recent increase in accessibility for research in Myanmar has allowed rapid advancements in the understanding of the geology of the country. Evolving depositional environments can be reconstructed in largely unstudied Oligocene deposits of the Salin sub-basin, of the Central Myanmar Basin. Data has been collected through a fieldwork campaign to target well-exposed sediments along the western margin of the basin. The studied outcrops span approximately one hundred kilometres from north to south, and a series of sedimentary logs, palaeocurrent data, 2D panel diagrams, and samples for petrographical analysis have been collected and interpreted. The Oligocene formations studied include the Shwezetaw, Paduang, and Okhmintaung, each of which show a broadly southwards-trending fluvio-deltaic environment of deposition. Towards the north, the lower Rupelian Shwezetaw Formation comprises thick fluviatile sandstones which grade southwards through macrotidal-dominated fluvio-deltaic interbedded siltstones and rare sandstones, into marine sandstones. Overlying this, the upper Rupelian Paduang Formation grades rapidly from rare fluvial sandstones towards the north of the basin into deltaic and marine interbedded sandstones and siltstones to the south. This formation is more marine in nature, suggesting a minor transgression throughout the lower Oligocene. By the time of deposition of the Okhmintaung Formation in the Chattian the observed deposits solely represent a tidally-influenced deltaic depositional environment, with very little temporal variation, suggesting a stable sea level. Despite the relatively unchanging depositional environment, the formations are approximately 4000 m thick, suggesting that sedimentation kept pace with relatively rapid subsidence. This current study, which will combine depositional environment reconstruction, provenance, and sediment routing analysis, will provide important insights into both the tectonic setting and the huge sediment accumulation

Depleted uranium (DU) mobility in the natural environment

International Nuclear Information System (INIS)

Ragnarsdottir, K.V.

2002-01-01

In 1999 the Balkan's conflict lead NATO war planes to leave 10x10 3 kg of depleted uranium (DU) in the environment of Kosovo and neighbouring states (UNEP, 2001). DU behaves in the same manner in the environment as natural uranium and it can be traced with isotopic analysis due to the fact that DU has the isotopic composition of 0.2% 235 U and 99.8% 2 38 U as opposed to natural uranium which has 0.7% 2 35 U and 99.3% 2 38 U. DU is a waste product of the nuclear industry which enrich nuclear fuel by 2 35 U. Large stock piles of DU therefore exist in countries that produce nuclear energy and/or nuclear weapons. The DU is given to the weapons industry for free (or cheap) and has been a popular choice for armour penetrating arsenal due to the high density of uranium (19 g cm -3 ) and therefore its high penetrating power. Indeed the arsenal used in Kosovo consisted of DU penetrators that were shot from A-10 aeroplanes. They weigh roughly 300 g and have the shape of a fat 9 cm long pencil. (author)

Oxygen plasma etching of silver-incorporated diamond-like carbon films

International Nuclear Information System (INIS)

Marciano, F.R.; Bonetti, L.F.; Pessoa, R.S.; Massi, M.; Santos, L.V.; Trava-Airoldi, V.J.

2009-01-01

Diamond-like carbon (DLC) film as a solid lubricant coating represents an important area of investigation related to space devices. The environment for such devices involves high vacuum and high concentration of atomic oxygen. The purpose of this paper is to study the behavior of silver-incorporated DLC thin films against oxygen plasma etching. Silver nanoparticles were produced through an electrochemical process and incorporated into DLC bulk during the deposition process using plasma enhanced chemical vapor deposition technique. The presence of silver does not affect significantly DLC quality and reduces by more than 50% the oxygen plasma etching. Our results demonstrated that silver nanoparticles protect DLC films against etching process, which may increase their lifetime in low earth orbit environment.

Oxygen plasma etching of silver-incorporated diamond-like carbon films

Energy Technology Data Exchange (ETDEWEB)

Marciano, F.R., E-mail: fernanda@las.inpe.b [Instituto Nacional de Pesquisas Espaciais (INPE), Laboratorio Associado de Sensores e Materiais (LAS), Av. dos Astronautas 1758, Sao Jose dos Campos, 12227-010, SP (Brazil); Instituto Tecnologico de Aeronautica (ITA), Centro Tecnico Aeroespacial (CTA), Pca. Marechal Eduardo Gomes, 50-Sao Jose dos Campos, 12228-900, SP (Brazil); Bonetti, L.F. [Clorovale Diamantes Industria e Comercio Ltda, Estr. do Torrao de Ouro, 500-Sao Jose dos Campos, 12229-390, SP (Brazil); Pessoa, R.S.; Massi, M. [Instituto Tecnologico de Aeronautica (ITA), Centro Tecnico Aeroespacial (CTA), Pca. Marechal Eduardo Gomes, 50-Sao Jose dos Campos, 12228-900, SP (Brazil); Santos, L.V.; Trava-Airoldi, V.J. [Instituto Nacional de Pesquisas Espaciais (INPE), Laboratorio Associado de Sensores e Materiais (LAS), Av. dos Astronautas 1758, Sao Jose dos Campos, 12227-010, SP (Brazil)

2009-08-03

Diamond-like carbon (DLC) film as a solid lubricant coating represents an important area of investigation related to space devices. The environment for such devices involves high vacuum and high concentration of atomic oxygen. The purpose of this paper is to study the behavior of silver-incorporated DLC thin films against oxygen plasma etching. Silver nanoparticles were produced through an electrochemical process and incorporated into DLC bulk during the deposition process using plasma enhanced chemical vapor deposition technique. The presence of silver does not affect significantly DLC quality and reduces by more than 50% the oxygen plasma etching. Our results demonstrated that silver nanoparticles protect DLC films against etching process, which may increase their lifetime in low earth orbit environment.

Silicon solar cell performance deposited by diamond like carbon thin film ;Atomic oxygen effects;

Science.gov (United States)

Aghaei, Abbas Ail; Eshaghi, Akbar; Karami, Esmaeil

2017-09-01

In this research, a diamond-like carbon thin film was deposited on p-type polycrystalline silicon solar cell via plasma-enhanced chemical vapor deposition method by using methane and hydrogen gases. The effect of atomic oxygen on the functioning of silicon coated DLC thin film and silicon was investigated. Raman spectroscopy, field emission scanning electron microscopy, atomic force microscopy and attenuated total reflection-Fourier transform infrared spectroscopy were used to characterize the structure and morphology of the DLC thin film. Photocurrent-voltage characteristics of the silicon solar cell were carried out using a solar simulator. The results showed that atomic oxygen exposure induced the including oxidation, structural changes, cross-linking reactions and bond breaking of the DLC film; thus reducing the optical properties. The photocurrent-voltage characteristics showed that although the properties of the fabricated thin film were decreased after being exposed to destructive rays, when compared with solar cell without any coating, it could protect it in atomic oxygen condition enhancing solar cell efficiency up to 12%. Thus, it can be said that diamond-like carbon thin layer protect the solar cell against atomic oxygen exposure.

Blood conservation with membrane oxygenators and dipyridamole.

Science.gov (United States)

Teoh, K H; Christakis, G T; Weisel, R D; Madonik, M M; Ivanov, J; Wong, P Y; Mee, A V; Levitt, D; Benak, A; Reilly, P

1987-07-01

Cardiopulmonary bypass induces platelet activation and dysfunction, which result in platelet deposition and depletion. Reduced platelet numbers and abnormal platelet function may contribute to postoperative bleeding. A membrane oxygenator may preserve platelets and reduce bleeding more than a bubble oxygenator, and the antiplatelet agent dipyridamole may protect platelets intraoperatively and reduce bleeding postoperatively. A prospective randomized trial was performed in 44 patients undergoing elective coronary artery bypass grafting to assess the effects of the membrane oxygenator and dipyridamole on platelet counts, platelet activation products, and postoperative bleeding. Patients who were randomized to receive a bubble oxygenator and no dipyridamole had the lowest postoperative platelet counts, the greatest blood loss, and the most blood products transfused. Platelet counts were highest and blood loss was least in patients randomized to receive a membrane oxygenator and dipyridamole (p less than .05). A bubble oxygenator with dipyridamole and a membrane oxygenator without dipyridamole resulted in intermediate postoperative platelet counts and blood loss. Arterial thromboxane B2 and platelet factor 4 concentrations were elevated on cardiopulmonary bypass in all groups. Both the membrane oxygenator and dipyridamole were independently effective (by multivariate analysis) in preserving platelets. Optimal blood conservation was achieved with a membrane oxygenator and dipyridamole.

Low-Flammability PTFE for High-Oxygen Environments

Science.gov (United States)

Walle, E.; Fallon, B.; Sheppard, A.

1986-01-01

Modified forming process removes volatile combustible materials. Flammability of cable-wrapping tape reduced by altering tape-manufacturing process. In new manufacturing process, tape formed by proprietary process of screw extrusion, followed by washing in solvent and drying. Tape then wrapped as before. Spectrogram taken after extrusion, washing, and drying shows lower hydrocarbon content. PTFE formed by new process suited to oxygen-rich environments. Safe in liquid oxygen of Space Shuttle tank and in medical uses; thin-wall shrinkable tubing in hospital test equipment, surgical instruments, and implants.

Biogeochemistry of Recently Discovered Oxygen-Depleted Mesoscale Eddies in the Open Eastern Tropical North Atlantic

Science.gov (United States)

Fiedler, B.; Grundle, D.; Löscher, C. R.; Schütte, F.; Hauss, H.; Karstensen, J.; Silva, P.; Koertzinger, A.

2016-02-01

Severely oxygen-depleted mesoscale features in the open eastern tropical North Atlantic, which are formed in the Mauritanian upwelling region, were discovered only recently. So far, few remote surveys conducted with autonomous platforms such as moorings, underwater gliders and profiling floats have provided a very first insight into these mesoscale eddies. Due to their hydrographic properties such water bodies are well isolated from ambient waters and therefore can develop severe near-surface oxygen deficits. In this presentation we show results from the first-ever biogeochemical survey of one of these anticyclonic mode-water eddies conducted in spring 2014 at the Cape Verde Ocean Observatory (CVOO) off West Africa. Very low oxygen concentrations of 4.5 µmol kg-1 associated with a CO2 partial pressure of 1164 µatm were found close to the core of the eddy (at 100 m depth). Measurements for nitrate and phosphate also show exceptional high values. Findings point to rapid oxygen consumption through remineralization of organic matter along with depressed lateral mixing of this water body. Indeed, rates for oxygen utilization (OUR) were found to be enhanced when compared to known values in the Atlantic. A closer look into the carbonate system inside the eddýs core revealed disadvantageous conditions for calcifying organisms with the pH dropping down to 7.6 and the Aragonite saturation level reaching 1 at the lower boundary of the euphotic zone. Finally, strong indications for a shift in nitrogen cycling in the core of the eddy from nitrification towards denitrification were found based on gene abundance and N2O-isotope analyses. To our knowledge such severe hypoxic and even suboxic near-surface conditions along with active denitrification have never been reported before in the open Atlantic Ocean.

Oxidation and microstrucure of V-Cr-Ti alloys exposed to oxygen-containing environments

Energy Technology Data Exchange (ETDEWEB)

Natesan, K. [Argonne National Lab., IL (United States); Uz, M. [Lafayette College, Easton, PA (United States); Ulie, T.

1997-08-01

The objectives of this task are to (a) evaluate the oxygen uptake of several V-Cr-Ti alloys as a function of temperature and oxygen partial pressure in the exposure environment, (b) examine the microstructural characteristics of oxide scales and oxygen trapped at the grain boundaries in the substrate alloys, and (c) evaluate the influence of alloy composition on oxygen uptake and develop correlation(s) between alloy composition, exposure environment, and temperature.

Oxidation and microstrucure of V-Cr-Ti alloys exposed to oxygen-containing environments

International Nuclear Information System (INIS)

Natesan, K.; Uz, M.; Ulie, T.

1997-01-01

The objectives of this task are to (a) evaluate the oxygen uptake of several V-Cr-Ti alloys as a function of temperature and oxygen partial pressure in the exposure environment, (b) examine the microstructural characteristics of oxide scales and oxygen trapped at the grain boundaries in the substrate alloys, and (c) evaluate the influence of alloy composition on oxygen uptake and develop correlation(s) between alloy composition, exposure environment, and temperature

Menadione induces the formation of reactive oxygen species and depletion of GSH-mediated apoptosis and inhibits the FAK-mediated cell invasion.

Science.gov (United States)

Kim, Yun Jeong; Shin, Yong Kyoo; Sohn, Dong Suep; Lee, Chung Soo

2014-09-01

Menadione induces apoptosis in tumor cells. However, the mechanism of apoptosis in ovarian cancer cells exposed to menadione is not clear. In addition, it is unclear whether menadione-induced apoptosis is mediated by the depletion of glutathione (GSH) contents that is associated with the formation of reactive oxygen species. Furthermore, the effect of menadione on the invasion and migration of human epithelial ovarian cancer cells has not been studied. Therefore, we investigated the effects of menadione exposure on apoptosis, cell adhesion, and cell migration using the human epithelial ovarian carcinoma cell lines OVCAR-3 and SK-OV-3. The results suggest that menadione may induce apoptotic cell death in ovarian carcinoma cell lines by activating the mitochondrial pathway and the caspase-8- and Bid-dependent pathways. The apoptotic effect of menadione appears to be mediated by the formation of reactive oxygen species and the depletion of GSH. Menadione inhibited fetal-bovine-serum-induced cell adhesion and migration of OVCAR-3 cells, possibly through the suppression the focal adhesion kinase (FAK)-dependent activation of cytoskeletal-associated components. Therefore, menadione might be beneficial in the treatment of epithelial ovarian adenocarcinoma and combination therapy.

Effects of nickel chloride and oxygen depletion on behaviour and vitality of zebrafish (Danio rerio, Hamilton, 1822) (Pisces, Cypriniformes) embryos and larvae

International Nuclear Information System (INIS)

Kienle, Cornelia; Koehler, H.-R.; Filser, Juliane; Gerhardt, Almut

2008-01-01

We examined acute (2 h exposure of 5-day-old larvae) and subchronic (exposure from fertilization up to an age of 11 days) effects of NiCl 2 .6H 2 O on embryos and larvae of zebrafish (Danio rerio), both alone and in combination with oxygen depletion. The following endpoints were recorded: acute exposure: locomotory activity and survival; subchronic exposure: hatching rate, deformations, locomotory activity (at 5, 8 and 11 days) and mortality. In acute exposures nickel chloride (7.5-15 mg Ni/L) caused decreasing locomotory activity. Oxygen depletion (≤2.45 ± 0.16 mg O 2 /L) also resulted in significantly reduced locomotory activity. In the subchronic test, exposure to ≥10 mg Ni/L resulted in delayed hatching at an age of 96 h, in decreased locomotory activity at an age of 5 days, and increased mortality at an age of 11 days (LC 20 = 9.5 mg Ni/L). The observed LOEC for locomotory activity (7.5 mg Ni/L) is in the range of environmentally relevant concentrations. Since locomotory activity was already affected by acute exposure, this parameter is recommended to supplement commonly recorded endpoints of toxicity. - Increasing concentrations of nickel chloride and decreasing concentrations of oxygen lead to reduced vitality and locomotory activity in Danio rerio embryos and larvae

Thermal stability of pulsed laser deposited iridium oxide thin films at low oxygen atmosphere

Science.gov (United States)

Gong, Yansheng; Wang, Chuanbin; Shen, Qiang; Zhang, Lianmeng

2013-11-01

Iridium oxide (IrO2) thin films have been regarded as a leading candidate for bottom electrode and diffusion barrier of ferroelectric capacitors, some process related issues need to be considered before integrating ferroelectric capacitors into memory cells. This paper presents the thermal stability of pulsed laser deposited IrO2 thin films at low oxygen atmosphere. Emphasis was given on the effect of post-deposition annealing temperature at different oxygen pressure (PO2) on the crystal structure, surface morphology, electrical resistivity, carrier concentration and mobility of IrO2 thin films. The results showed that the thermal stability of IrO2 thin films was strongly dependent on the oxygen pressure and annealing temperature. IrO2 thin films can stably exist below 923 K at PO2 = 1 Pa, which had a higher stability than the previous reported results. The surface morphology of IrO2 thin films depended on PO2 and annealing temperature, showing a flat and uniform surface for the annealed films. Electrical properties were found to be sensitive to both the annealing temperature and oxygen pressure. The room-temperature resistivity of IrO2 thin films with a value of 49-58 μΩ cm increased with annealing temperature at PO2 = 1 Pa. The thermal stability of IrO2 thin films as a function of oxygen pressure and annealing temperature was almost consistent with thermodynamic calculation.

X-ray photoelectron spectroscopy investigation of ion beam sputtered indium tin oxide films as a function of oxygen pressure during deposition

International Nuclear Information System (INIS)

Nelson, A.J.; Aharoni, H.

1987-01-01

X-ray photoelectron spectroscopy analysis was performed on ion beam sputter deposited films of indium tin oxide as a function of O 2 partial pressure during deposition. The oxygen partial pressure was varied over the range of 2.5 x 10 -6 --4.0 x 10 -5 Torr. Changes in composition as well as in the deconvoluted In 3d 5 /sub // 2 , Sn 3d 5 /sub // 2 , and O 1s core level spectra were observed and correlated with the variation of the oxygen partial pressure during deposition. Results show that the films become increasingly stoichiometric as P/sub =/ is increased and that the excess oxygen introduced during deposition is bound predominantly to the Sn and has little or no effect on the In--O bonding

Resistive Oxygen Gas Sensors for Harsh Environments

Science.gov (United States)

Moos, Ralf; Izu, Noriya; Rettig, Frank; Reiß, Sebastian; Shin, Woosuck; Matsubara, Ichiro

2011-01-01

Resistive oxygen sensors are an inexpensive alternative to the classical potentiometric zirconia oxygen sensor, especially for use in harsh environments and at temperatures of several hundred °C or even higher. This device-oriented paper gives a historical overview on the development of these sensor materials. It focuses especially on approaches to obtain a temperature independent behavior. It is shown that although in the past 40 years there have always been several research groups working concurrently with resistive oxygen sensors, novel ideas continue to emerge today with respect to improvements of the sensor response time, the temperature dependence, the long-term stability or the manufacture of the devices themselves using novel techniques for the sensitive films. Materials that are the focus of this review are metal oxides; especially titania, titanates, and ceria-based formulations. PMID:22163805

Depositional environment of the San Miguel lignite deposit in Atascosa and McMullen Counties, Texas

Energy Technology Data Exchange (ETDEWEB)

Gowan, S.W.

1985-01-01

An analysis of the environment of deposition of the San Miguel lignite deposit was carried out in order to understand newly discovered characteristics of the deposit. The environment of deposition of the overburden and underburden was evaluated through an interpretation of three continuous cores. Four coal cores and a highwall section were carefully described to determine the depositional environmental of the coal seams and partings. These studies were supplemented by the construction of seam and parting isopachs, and the analysis of the distribution of sulfur isotopes, sulfur, forms, and total sulfur within the coal. The sedimentary package is composed of a basal prograding barrier that beach, dune, and back-barrier sands. This unit correlates with a downdip sand that was also interpreted as a prograding barrier by other authors. The barrier is overlain by a series of slit and clay deposits of lagoonal, tidal flat, and tidal channel origin. These deposits are capped by restricted lagoon sediments composed of green, calcareous clays that occasionally contain shell layers. The restricted lagoon deposits formed when the barrier closed the lagoon off from the sea. Peat forming freshwater swamps eventually became established behind the barrier and on top of the restricted lagoon sediments. The parting isopachs reveal a reticulate morphology similar to the mangrove swamps located lateral to the modern Niger River Delta. The partings represent vegetated tidal flat deposits that formed during periodic invasions by the sea that killed the swamp and inundated the peat with sulfate rich water. The lignite interval is capped by open lagoon and tidal flat sediments.

Environment of deposition of the Awgu Formation (Late Cretaceous ...

African Journals Online (AJOL)

PROMOTING ACCESS TO AFRICAN RESEARCH ... The Awgu Formation is a linear NE-SW trending sedimentary deposit ... in the fine arenaceous facies, suggest a shallow marine depositional environment not exceeding 50 m water depth. ... Senegal (6); Sierra Leone (1); South Africa (96); South Sudan (1); Sudan (3) ...

Ecological considerations of natural and depleted uranium

International Nuclear Information System (INIS)

Hanson, W.C.

1980-01-01

Depleted 238 U is a major by-product of the nuclear fuel cycle for which increasing use is being made in counterweights, radiation shielding, and ordnance applications. This paper (1) summarizes the pertinent literature on natural and depleted uranium in the environment, (2) integrates results of a series of ecological studies conducted at Los Alamos Scientific Laboratory (LASL) in New Mexico where 70,000 kg of depleted and natural uranium has been expended to the environment over the past 34 years, and (3) synthesizes the information into an assessment of the ecological consequences of natural and depleted uranium released to the environment by various means. Results of studies of soil, plant, and animal communities exposed to this radiation and chemical environment over a third of a century provide a means of evaluating the behavior and effects of uranium in many contexts

Effect of oxygen pressure of SiOx buffer layer on the electrical properties of GZO film deposited on PET substrate

International Nuclear Information System (INIS)

Ahn, Byung Du; Ko, Young Gun; Oh, Sang Hoon; Song, Jean-Ho; Kim, Hyun Jae

2009-01-01

The present work was made to investigate the effect of oxygen pressure of SiO x layer on the electrical properties of Ga-doped ZnO (GZO) films deposited on poly-ethylene telephthalate (PET) substrate by utilizing the pulsed-laser deposition at ambient temperature. For this purpose, the SiO x buffer layers were deposited at various oxygen pressures ranging from 13.3 to 46.7 Pa. With increasing oxygen pressure during the deposition of SiO x layer as a buffer, the electrical resistivity of GZO/SiO x /PET films gradually decreased from 7.6 x 10 -3 to 6.8 x 10 -4 Ω.cm, due to the enhanced mobility of GZO films. It was mainly due to the grain size of GZO films related to the roughened surface of the SiO x buffer layers. In addition, the average optical transmittance of GZO/SiO x /PET films in a visible regime was estimated to be ∼ 90% comparable to that of GZO deposited onto a glass substrate.

Effect of vapor-phase oxygen on chemical vapor deposition growth of graphene

Science.gov (United States)

Terasawa, Tomo-o.; Saiki, Koichiro

2015-03-01

To obtain a large-area single-crystal graphene, chemical vapor deposition (CVD) growth on Cu is considered the most promising. Recently, the surface oxygen on Cu has been found to suppress the nucleation of graphene. However, the effect of oxygen in the vapor phase was not elucidated sufficiently. Here, we investigate the effect of O2 partial pressure (PO2) on the CVD growth of graphene using radiation-mode optical microscopy. The nucleation density of graphene decreases monotonically with PO2, while its growth rate reaches a maximum at a certain pressure. Our results indicate that PO2 is an important parameter to optimize in the CVD growth of graphene.

Oxygen in the Martian atmosphere: Regulation of PO2 by the deposition of iron formations on Mars

Science.gov (United States)

Burns, Roger G.

1992-01-01

During Earth's early history, and prior to the evolution of its present day oxygenated atmosphere, extensive iron rich siliceous sedimentary rocks were deposited, consisting of alternating layers of silica (chert) and iron oxide minerals (hematite and magnetite). The banding in iron formations recorded changes of atmosphere-hydrosphere interactions near sea level in the ancient ocean, which induced the oxidation of dissolved ferrous iron, precipitation of insoluble ferric oxides and silica, and regulation of oxygen in Earth's early atmosphere. Similarities between the Archean Earth and the composition of the present day atmosphere on Mars, together with the pervasive presence of ferric oxides in the Martian regolith suggest that iron formation might also have been deposited on Mars and influenced the oxygen content of the Martian atmosphere. Such a possibility is discussed here with a view to assessing whether the oxygen content of the Martian atmosphere has been regulated by the chemical precipitation of iron formations on Mars.

Gamma spectrometric determination of depleted Uranium in Yugoslavia

International Nuclear Information System (INIS)

Pantelic, G.; Eremic Savkovic, M.; Javorina, L.; Tanaskovic, I.; Vuletic, V.; Milacic, S.

2002-01-01

The radiation protection is very important interdisciplinary research field due to the presence of the radiation in daily life. The systematic examination of radioactive contamination of various environmental samples was established forty years ago in the Institute of Occupational and Radiological Health Dr Dragomir Karajovic for the sake of preventive protection of population and environment from the harmful effect of ionizing radiation. The global sources of radionuclide contamination in our country are the fallout due to previous nuclear testing and the deposition of radionuclides from the region of Chernobyl accident. The contents of radionuclides were determined in aerosol, soil, fallout (wet and dry deposition), rivers, lakes, drinking water, human and animal food. The samples were collected in several locations of the Republic of Serbia and in regular time intervals, according to methods determined by the regulation. The regulations and the monitoring programs were updated after the Chernobyl accident. In the recent time, after the NATO aggression, we analyzed depleted uranium content in the environmental samples. We used high-resolution gamma spectrometry measurements, because of their simplicity and accuracy. Aims of the control were to asses the increase of radioactivity above the natural levels in the immediate and near vicinity of the bomb craters, to asses the corresponding effect of changed natural radioactivity on the health of the population living in these places and finding unexploded depleted uranium bullets

The corrosion of depleted uranium in terrestrial and marine environments.

Science.gov (United States)

Toque, C; Milodowski, A E; Baker, A C

2014-02-01

Depleted Uranium alloyed with titanium is used in armour penetrating munitions that have been fired in a number of conflict zones and testing ranges including the UK ranges at Kirkcudbright and Eskmeals. The study presented here evaluates the corrosion of DU alloy cylinders in soil on these two UK ranges and in the adjacent marine environment of the Solway Firth. The estimated mean initial corrosion rates and times for complete corrosion range from 0.13 to 1.9 g cm(-2) y(-1) and 2.5-48 years respectively depending on the particular physical and geochemical environment. The marine environment at the experimental site was very turbulent. This may have caused the scouring of corrosion products and given rise to a different geochemical environment from that which could be easily duplicated in laboratory experiments. The rate of mass loss was found to vary through time in one soil environment and this is hypothesised to be due to pitting increasing the surface area, followed by a build up of corrosion products inhibiting further corrosion. This indicates that early time measurements of mass loss or corrosion rate may be poor indicators of late time corrosion behaviour, potentially giving rise to incorrect estimates of time to complete corrosion. The DU alloy placed in apparently the same geochemical environment, for the same period of time, can experience very different amounts of corrosion and mass loss, indicating that even small variations in the corrosion environment can have a significant effect. These effects are more significant than other experimental errors and variations in initial surface area. Copyright © 2013. Published by Elsevier Ltd.

A synthesis of atmospheric mercury depletion event chemistry in the atmosphere and snow

Directory of Open Access Journals (Sweden)

A. J. Poulain

2008-03-01

Full Text Available It was discovered in 1995 that, during the spring time, unexpectedly low concentrations of gaseous elemental mercury (GEM occurred in the Arctic air. This was surprising for a pollutant known to have a long residence time in the atmosphere; however conditions appeared to exist in the Arctic that promoted this depletion of mercury (Hg. This phenomenon is termed atmospheric mercury depletion events (AMDEs and its discovery has revolutionized our understanding of the cycling of Hg in Polar Regions while stimulating a significant amount of research to understand its impact to this fragile ecosystem. Shortly after the discovery was made in Canada, AMDEs were confirmed to occur throughout the Arctic, sub-Artic and Antarctic coasts. It is now known that, through a series of photochemically initiated reactions involving halogens, GEM is converted to a more reactive species and is subsequently associated to particles in the air and/or deposited to the polar environment. AMDEs are a means by which Hg is transferred from the atmosphere to the environment that was previously unknown. In this article we review Hg research taken place in Polar Regions pertaining to AMDEs, the methods used to collect Hg in different environmental media, research results of the current understanding of AMDEs from field, laboratory and modeling work, how Hg cycles around the environment after AMDEs, gaps in our current knowledge and the future impacts that AMDEs may have on polar environments. The research presented has shown that while considerable improvements in methodology to measure Hg have been made but the main limitation remains knowing the speciation of Hg in the various media. The processes that drive AMDEs and how they occur are discussed. As well, the role that the snow pack and the sea ice play in the cycling of Hg is presented. It has been found that deposition of Hg from AMDEs occurs at marine coasts and not far inland and that a fraction of the deposited Hg does

Potential For Stratospheric Ozone Depletion During Carboniferous

Science.gov (United States)

Bill, M.; Goldstein, A. H.

Methyl bromide (CH3Br) constitutes the largest source of bromine atoms to the strato- sphere whereas methyl chloride (CH3Cl) is the most abundant halocarbon in the tro- posphere. Both gases play an important role in stratospheric ozone depletion. For in- stance, Br coupled reactions are responsible for 30 to 50 % of total ozone loss in the polar vortex. Currently, the largest natural sources of CH3Br and CH3Cl appear to be biological production in the oceans, inorganic production during biomass burning and plant production in salt marsh ecosystems. Variations of paleofluxes of CH3Br and CH3Cl can be estimated by analyses of oceanic paleoproductivity, stratigraphic analyses of frequency and distribution of fossil charcoal indicating the occurrence of wildfires, and/or by paleoreconstruction indicating the extent of salt marshes. Dur- ing the lower Carboniferous time (Tournaisian-Visean), the southern margin of the Laurasian continent was characterized by charcoal deposits. Estimation on frequency of charcoal layers indicates that wildfires occur in a range of 3-35 years (Falcon-Lang 2000). This suggests that biomass burning could be an important source of CH3Br and CH3Cl during Tournaisian-Viesan time. During Tounaisian and until Merame- cian carbon and oxygen isotope records have short term oscillations (Bruckschen et al. 1999, Mii et al. 1999). Chesterian time (mid- Carboniferous) is marked by an in- crease in delta18O values ( ~ 2 permil) and an increase of glacial deposit frequency suggesting lower temperatures. The occurrence of glacial deposits over the paleopole suggests polar conditions and the associated special features of polar mete- orology such as strong circumpolar wind in the stratosphere (polar vortex) and polar stratospheric clouds. Thus, conditions leading to polar statospheric ozone depletion can be found. Simultaneously an increase in delta13C values is documented. We interpret the positive shift in delta13C as a result of higher bioproductivity

Integrated turbomachine oxygen plant

Science.gov (United States)

Anand, Ashok Kumar; DePuy, Richard Anthony; Muthaiah, Veerappan

2014-06-17

An integrated turbomachine oxygen plant includes a turbomachine and an air separation unit. One or more compressor pathways flow compressed air from a compressor through one or more of a combustor and a turbine expander to cool the combustor and/or the turbine expander. An air separation unit is operably connected to the one or more compressor pathways and is configured to separate the compressed air into oxygen and oxygen-depleted air. A method of air separation in an integrated turbomachine oxygen plant includes compressing a flow of air in a compressor of a turbomachine. The compressed flow of air is flowed through one or more of a combustor and a turbine expander of the turbomachine to cool the combustor and/or the turbine expander. The compressed flow of air is directed to an air separation unit and is separated into oxygen and oxygen-depleted air.

Carbon sequestration in depleted oil shale deposits

Science.gov (United States)

Burnham, Alan K; Carroll, Susan A

2014-12-02

A method and apparatus are described for sequestering carbon dioxide underground by mineralizing the carbon dioxide with coinjected fluids and minerals remaining from the extraction shale oil. In one embodiment, the oil shale of an illite-rich oil shale is heated to pyrolyze the shale underground, and carbon dioxide is provided to the remaining depleted oil shale while at an elevated temperature. Conditions are sufficient to mineralize the carbon dioxide.

Impact of mineral resource depletion

CSIR Research Space (South Africa)

Brent, AC

2006-09-01

Full Text Available In a letter to the editor, the authors comment on BA Steen's article on "Abiotic Resource Depletion: different perceptions of the problem with mineral deposits" published in the special issue of the International Journal of Life Cycle Assessment...

Estimation of site specific deposition velocities and mass interception factor using 7Be as a tracer in Kudankulam environment

International Nuclear Information System (INIS)

Selvi, B.S.; Vijayakumar, B.; Ravi, P.M.

2018-01-01

Beryllium-7 ( 7 Be) is a cosmogenic radionuclide formed in the atmosphere when cosmic ray produced neutrons and protons disintegrate the atomic nucleus of nitrogen and oxygen in to lighter fragments. ' 7 Be is found naturally in air, rainwater, vegetation, soils and sediments as well as lake and ocean waters. Due to its continuous production in the atmosphere, its relatively short half-life (53.3 days), and its ease of measurement by gamma spectrometry, 7 Be has proven to be a useful tool for tracing and quantifying environmental processes such as atmospheric deposition, atmospheric transport and soil erosion etc. A systematic study is carried out to estimate the site specific deposition velocities and the mass interception factor around the Kudankulam environment

Nature gives us strength: exposure to nature counteracts ego-depletion.

Science.gov (United States)

Chow, Jason T; Lau, Shun

2015-01-01

Previous research rarely investigated the role of physical environment in counteracting ego-depletion. In the present research, we hypothesized that exposure to natural environment counteracts ego-depletion. Three experiments were conducted to test this hypothesis. In Experiment 1, initially depleted participants who viewed pictures of nature scenes showed greater persistence on a subsequent anagram task than those who were given a rest period. Experiment 2 expanded upon this finding by showing that natural environment enhanced logical reasoning performance after ego-depleting task. Experiment 3 adopted a two- (depletion vs. no-depletion) -by-two (nature exposure vs. urban exposure) factorial design. We found that nature exposure moderated the effect of depletion on anagram task performance. Taken together, the present studies offer a viable and novel strategy to mitigate the negative impacts of ego-depletion.

Vitamin D Depletion in Pregnancy Decreases Survival Time, Oxygen Saturation, Lung Weight and Body Weight in Preterm Rat Offspring

DEFF Research Database (Denmark)

Lykkedegn, Sine; Sorensen, Grith Lykke; Beck-Nielsen, Signe Sparre

2016-01-01

Animal studies suggest a role of vitamin D in fetal lung development although not studied in preterm animals. We tested the hypothesis that vitamin D depletion aggravates respiratory insufficiency in preterm rat offspring. Furthermore, the effects of vitamin D depletion on growth and lung...... surfactant were investigated. Female Sprague-Dawley rats were randomly assigned low vitamin D (VDL) or control diet before mating and followed with serum 25-hydroxyvitamin D (s-25(OH)D) determinations. After cesarean section at gestational day 19 (E19) or day 22 (E22), placental weight, birth weight, crown......-rump-length (CRL), oxygenation (SaO2) at 30 min and survival time were recorded. The pup lungs were analyzed for phospholipid levels, surfactant protein A-D mRNA and the expression of the vitamin D receptor (VDR). S-25(OH)D was significantly lower in the VDL group at cesarean section (12 vs. 30nmol/L, p

The enhanced cytotoxicity of misonidazole in the thiol depleted state - An oxygen dependent mechanism

International Nuclear Information System (INIS)

Tuttle, S.W.; Varnes, M.E.; Donahue, L.; Biaglow, J.E.

1985-01-01

Incubating A549 cells in the presence of L-buthionine-S, R-sulfoximine and misonidazole under aerobic conditions results in lowered rates of cell growth and greater cytotoxicity than is seen with either drug alone. The authors previously demonstrated the accumulation of hydrogen peroxide from cells treated with misonidazole following the inhibition of GSH-peroxidase with thiol depleting agents. They hypothesize that the enhancement of misonidazole toxicity by L-BSO results from the increased exposure to hydrogen peroxide, and the possible formation of the highly reactive hydroxyl radical in the presence of trace metals via Fenton chemistry. Support for this hypothesis comes from their observations that addition of radical scavengers (such as SOD and catalase) and nutritional antioxidants (vitamin E) to the culture medium will partially inhibit the cytotoxic effects. Further work is being done to measure the products of reaction of toxic oxygen species with cellular macromolecules, i.e. lipids

Enhancement of Jc of MgB2 thin films by introduction of oxygen during deposition

International Nuclear Information System (INIS)

Mori, Zon; Doi, Toshiya; Hakuraku, Yoshinori; Kitaguchi, Hitoshi

2006-01-01

The introduction of various pinning center are examined as the effective means for improvement of J c of MgB 2 thin films. We have investigated the effects of introduction of oxygen during deposition on the superconducting properties of MgB 2 thin films. MgB 2 thin films were prepared on polished sapphire C(0001) single crystal substrates by using electron beam evaporation technique (EB) without any post-annealing. The background pressure was less than 1.3x10 -6 Pa. The evaporation flux ratio of Mg was set at 30 times as high as that of B, and the growth rate of MgB 2 film was 1nm/s. The film thickness was typically 300nm at 5min deposition. The substrate temperature was 245 deg. C. Under these conditions, we controlled the oxygen partial pressure (P O 2 ) within the range from 1.3x10 -6 to 1.3x10 -3 Pa by using a quadrapole mass spectrometer. Although T c of deposited thin film decreased in order of P O 2 , ΔM in the magnetization hysteresis loops measured from 0 to 6T at 4.2K increased up to 1.3x10 -5 . On the other hand, thin film prepared under P O 2 of 1.3x10 -3 Pa does not show superconducting transition. Between these films, there is no difference in the crystal structure from X-ray diffraction (XRD). These results suggest that the pinning center in the thin films increased by introduction of oxygen. Extremely small amount of oxygen introduction has enabled the control of growth of oxide

Potential involvement of oxygen intermediates and glutathione depletion in UV-induced epidermal cell injury in vitro

International Nuclear Information System (INIS)

Hsieh, G.C.; Acosta, D.

1991-01-01

Generation of reactive oxygen species (ROS) and depletion of glutathione (GSH) are suggested as the cytotoxic mechanisms for UVB-induced cellular damage. Primary monolayer cultures of epidermal keratinocytes (KCs) prepared from the skin of neonatal rats were irradiated with UVB at levels of 0.25-3.0 J/cm 2 . Cytotoxicity was measured at 3, 6, and 12 hr after UVB radiation. Exposure of KCs to UVB resulted in time- and dose-related toxic responses as determined by plasma membrane integrity, lysosomal function and mitochondrial metabolic activity. Irradiated KCs generated superoxide in a dose-dependent manner when compared to sham-irradiated cells. Superoxide formation, which occurred before and concomitant with cell injury, was decreased by superoxide dismutase (SOD). Cell injury was also significantly prevented by ROS scavengers, SOD and catalase. Pretreatment of cells with endocytosis inhibitors, cytochalasin B and methylamine, suppressed the ability of SOD and catalase to protect keratinocytes from UVB-induced toxicity. Irradiation of cells with UVB caused rapid depletion of GSH to about 30% of unirradiated levels within 15 min. UVB-irradiation led to a rapid transient increase in GSH peroxidase activity, concomitant with a marked decrease in the GSH/GSSG ratio. After 1 hr., while the GSH/GSSG ratio remained low, the GSH peroxidase activity declined below the control levels in UVB-treated epidermal cells. Following extensive GSH depletion in cells preincubated with 0.1 mM buthiomine sulfoximine, KCs became strongly sensitized to the cytotoxic action of UVB. These results indicate that UVB-induced cell injury in cultured KCs may be mediated by ROs and that endogenous GSH may play an important protective role against the cytotoxic action of UVB

Application of Markov chains-entropy to analysis of depositional environments

Energy Technology Data Exchange (ETDEWEB)

Men Guizhen; Shi Xiaohong; Zhao Shuzhi

1989-01-01

The paper systematically and comprehensively discussed application of Markov chains-entropy to analysis of depositional environments of the upper Carboniferous series Taiyuan Formation in Anjialing, Pingshuo open-cast mine, Shanxi. Definite geological meanings were given respectively to calculated values of transition probability matrix, extremity probability matrix, substitution matrix and the entropy. The lithologic successions of coarse-fine-coarse grained layers from bottom upwards in the coal-bearing series made up the general symmetric cyclic patterns. It was suggested that the coal-bearing strata deposited in the coal-forming environment in delta plain-littoral swamps. Quantitative study of cyclic visibility and variation of formation was conducted. The assemblage relation among stratigraphic sequences and the significance of predicting vertical change were emphasized. Results of study showed that overall analysis of Markov chains was an effective method for analysis of depositional environments of coal-bearing strata. 2 refs., 5 figs.

Plasma Deposited Thin Iron Oxide Films as Electrocatalyst for Oxygen Reduction Reaction in Proton Exchange Membrane Fuel Cells

Directory of Open Access Journals (Sweden)

Lukasz JOZWIAK

2017-02-01

Full Text Available The possibility of using plasma deposited thin films of iron oxides as electrocatalyst for oxygen reduction reaction (ORR in proton exchange membrane fuel cells (PEMFC was examined. Results of energy-dispersive X-ray spectroscopy (EDX and X-ray photoelectron spectroscopy (XPS analysis indicated that the plasma deposit consisted mainly of FeOX structures with the X parameter close to 1.5. For as deposited material iron atoms are almost exclusively in the Fe3+ oxidation state without annealing in oxygen containing atmosphere. However, the annealing procedure can be used to remove the remains of carbon deposit from surface. The single cell test (SCT was performed to determine the suitability of the produced material for ORR. Preliminary results showed that power density of 0.23 mW/cm2 could be reached in the tested cell.DOI: http://dx.doi.org/10.5755/j01.ms.23.1.14406

Modification of low temperature deposited LiMn2O4 thin film cathodes by oxygen plasma irradiation

International Nuclear Information System (INIS)

Chen, Chen Chung; Chiu, Kuo-Feng; Lin, Kun Ming; Lin, Hsin Chih

2009-01-01

Lithium manganese oxides have been deposited by radio frequency magnetron sputter deposition with relatively lower annealing temperatures and then post-treated with a radio frequency (rf) driven oxygen plasma. Following oxygen plasma irradiation, the film properties were modified, and the performance of the thin film cathode has been enhanced. The electrochemical properties of the treated thin-film cathodes were characterized and compared. The results showed that the samples with moderate plasma treatment also maintained good cyclic properties as cycled at a wide range potential window of 2.0 V-4.5 V. Its electrochemical properties were significantly improved by this process, even though the films were prepared under low annealing temperature.

Fate of leaf litter deposits and impacts on oxygen availability in bank filtration column studies.

Science.gov (United States)

Bayarsaikhan, Uranchimeg; Filter, Josefine; Gernert, Ulrich; Jekel, Martin; Ruhl, Aki Sebastian

2018-07-01

Degradation of particulate organic carbon (POC) such as leaf litter might deplete dissolved oxygen within the upper layers of bank filtration, an efficient and robust barrier for pathogens and for various organic micro-pollutants (OMP) in water supply systems worldwide. The degradation of OMP during bank filtration depends on the redox conditions. The present study aimed at identifying the impacts and fates of different local leaves on the oxygen consumption and the possible biological degradation of indicator OMP. Oxygen concentrations initially decreased within the columns from around 8 mg/L in the influent to low concentrations indicating extensive consumption within a short travel distance. Still a substantial oxygen consumption was observed after 250 days. OMP concentrations were not significantly affected by the microbial processes. A layer of calcium carbonate crystallites was observed on the POC layer. Some leaf fragments appeared to be persistant towards degradation and the carbon content relative to nitrogen and sulfur contents decreased within 250 days. The results demonstrate that trees at bank filtration sites might have a strong long-term impact on the subsurface redox conditions. Copyright © 2018 Elsevier Inc. All rights reserved.

Optical response of oxygen deficient La{sub 0.7}Sr{sub 0.3}MnO{sub 3} thin films deposited by pulsed laser deposition

Energy Technology Data Exchange (ETDEWEB)

Cesaria, M., E-mail: maura.cesaria@le.infn.it [Department of Mathematics and Physics “Ennio De Giorgi”, University of Salento, Via Arnesano, 73100 Lecce (Italy); Caricato, A.P.; Leggieri, G.; Martino, M. [Department of Mathematics and Physics “Ennio De Giorgi”, University of Salento, Via Arnesano, 73100 Lecce (Italy); Maruccio, G. [Department of Mathematics and Physics “Ennio De Giorgi”, University of Salento, Via Arnesano, 73100 Lecce (Italy); National Nanotechnology Laboratory (NNL)-Nanoscience Institute-CNR, Via Arnesano, 73100 Lecce (Italy)

2013-10-31

The optical response of 200 nm thick La{sub 0.7}Sr{sub 0.3}MnO{sub (3−δ)} films, deposited by pulsed laser deposition on amorphous silica substrates heated at nearly 600 °C, under different oxygen pressures (0.1 Pa, 0.5 Pa, 1 Pa, 5 Pa and 10 Pa), is reported. The effects of the oxygen non-stoichiometry are investigated at room temperature dealing with the absorption coefficient and the Tauc's plot method rather than conventional optical conductivity. The absorption curves are evaluated by an algorithm able to realistically describe the behavior of thin films without exploiting numerical extrapolations or simplified theoretical models or ab-initio calculations. Optical features, tunable by the growth oxygen pressure, are discussed based on the known theoretical and experimental scenario. - Highlights: • Overview of the La{sub 0.7}Sr{sub 0.3}MnO{sub 3} basics to highlight basic questions to be assessed. • Optical analysis by the absorption coefficient rather than optical conductivity. • Realistic absorption response that avoids numerical refinements and simulations. • Analysis of the role of oxygen vacancies in tuning the electronic dispersion. • First investigation of direct and indirect transitions by the Tauc's plot.

Effects of oxygen addition in reactive cluster beam deposition of tungsten by magnetron sputtering with gas aggregation

Energy Technology Data Exchange (ETDEWEB)

Polášek, J., E-mail: xpolasekj@seznam.cz [Department of Surface and Plasma Science, Faculty of Mathematics and Physic, Charles University, V Holešovičkách 2, Prague 8, CZ-18000 (Czech Republic); Mašek, K. [Department of Surface and Plasma Science, Faculty of Mathematics and Physic, Charles University, V Holešovičkách 2, Prague 8, CZ-18000 (Czech Republic); Marek, A.; Vyskočil, J. [HVM Plasma Ltd., Na Hutmance 2, Prague 5, CZ-158 00 (Czech Republic)

2015-09-30

In this work, we investigated the possibilities of tungsten and tungsten oxide nanoclusters generation by means of non-reactive and reactive magnetron sputtering with gas aggregation. It was found that in pure argon atmosphere, cluster aggregation proceeded in two regimes depending on argon pressure in the aggregation chamber. At the lower pressure, cluster generation was dominated by two-body collisions yielding larger clusters (about 5.5 nm in diameter) at lower rate. At higher pressures, cluster generation was dominated by three-body collisions yielding smaller clusters (3–4 nm in diameter) at higher rate. The small amount of oxygen admixture in the aggregation chamber had considerable influence on cluster aggregation process. At certain critical pressure, the presence of oxygen led to the raise of deposition rate and cluster size. Resulting clusters were composed mostly of tungsten trioxide. The oxygen pressure higher than critical led to the target poisoning and the decrease in the sputtering rate. Critical oxygen pressure decreased with increasing argon pressure, suggesting that cluster aggregation process was influenced by atomic oxygen species (namely, O{sup −} ion) generated by oxygen–argon collisions in the magnetron plasma. - Highlights: • Formation of tungsten and tungsten oxide clusters was observed. • Two modes of cluster aggregation in pure argon atmosphere were found. • Dependence of cluster deposition speed and size on oxygen admixture was observed. • Changes of dependence on oxygen with changing argon pressure were described.

Effects of oxygen addition in reactive cluster beam deposition of tungsten by magnetron sputtering with gas aggregation

International Nuclear Information System (INIS)

Polášek, J.; Mašek, K.; Marek, A.; Vyskočil, J.

2015-01-01

In this work, we investigated the possibilities of tungsten and tungsten oxide nanoclusters generation by means of non-reactive and reactive magnetron sputtering with gas aggregation. It was found that in pure argon atmosphere, cluster aggregation proceeded in two regimes depending on argon pressure in the aggregation chamber. At the lower pressure, cluster generation was dominated by two-body collisions yielding larger clusters (about 5.5 nm in diameter) at lower rate. At higher pressures, cluster generation was dominated by three-body collisions yielding smaller clusters (3–4 nm in diameter) at higher rate. The small amount of oxygen admixture in the aggregation chamber had considerable influence on cluster aggregation process. At certain critical pressure, the presence of oxygen led to the raise of deposition rate and cluster size. Resulting clusters were composed mostly of tungsten trioxide. The oxygen pressure higher than critical led to the target poisoning and the decrease in the sputtering rate. Critical oxygen pressure decreased with increasing argon pressure, suggesting that cluster aggregation process was influenced by atomic oxygen species (namely, O"− ion) generated by oxygen–argon collisions in the magnetron plasma. - Highlights: • Formation of tungsten and tungsten oxide clusters was observed. • Two modes of cluster aggregation in pure argon atmosphere were found. • Dependence of cluster deposition speed and size on oxygen admixture was observed. • Changes of dependence on oxygen with changing argon pressure were described.

The Toxicity of Depleted Uranium

OpenAIRE

Briner, Wayne

2010-01-01

Depleted uranium (DU) is an emerging environmental pollutant that is introduced into the environment primarily by military activity. While depleted uranium is less radioactive than natural uranium, it still retains all the chemical toxicity associated with the original element. In large doses the kidney is the target organ for the acute chemical toxicity of this metal, producing potentially lethal tubular necrosis. In contrast, chronic low dose exposure to depleted uranium may not produce a c...

Comparison of braided-stream depositional environment and uranium deposits at Saint Anthony underground mine

International Nuclear Information System (INIS)

Baird, C.W.; Martin, K.W.; Lowry, R.M.

1980-01-01

United Nuclear's Saint Anthony mine, located in the Laguna district, produces uranium ore from the Jackpile sandstone unit of the Morrison Formation. The Jackpile sediments were deposited in a fluvial environment characterized by aridity, gentle slope, distant source area, and limited flow volume. Resultant stratigraphy consists of an intricate assemblage of trough and tabular cross-stratification grading to near massive bedding at some locations. Interbedded with the Jackpile sands are green mudstones and siltstones that commonly display irregular thicknesses of less than 2 ft and that are laterally discontinuous. Major penecontemporaneous and postdepositional alteration of originally deposited sands, silts, and clays includes: 1) infiltration and filling of interstices by kaolinitic clays; 2) mobilization and relocation of organic carbonaceous material; and 3) geochemical alteration of mineral constituents and fixation of uranium ions in organic carbonaceous material. Mineralized zones of economic volume display a spatial relationship to bedding features indicative of loosely packed sand deposited in dune and trough foresets. This relationship indicates possible permeability control by initial stratigraphy upon the flow of mineralizing solutions. Additionally, the low-energy foreset environment facilitates the accumulation of low-specific-gravity carbonaceous material necessary for interaction with mineralizing solutions. Large volumes of loosely packed foreset sands accumulate in transverse bars in braided-stream environments. These structures have a great potential for conducting large volumes of mineralizing fluids and hosting economic quantities of uranium ore

The influence of oxygen on the induction of radiation damage in DNA in mammalian cells after sensitization by intracellular glutathione depletion

International Nuclear Information System (INIS)

Schans, G.P. van der; Vos, O.; Roos-Verheij, W.S.D.; Lohman, P.H.M.

1986-05-01

Treatment of mammalian cells with buthionine sulphoximine (BSO) or diethyl maleate (DEM) results in a decrease in the intracellular GSH (glutathione) and NPSH (non-protein-bound SH) levels. The effect of depletion of GSH and NPSH on radiosensitivity was studied in relation to the concentration of oxygen during irradiation. Single- and double-strand DNA breaks (ssb and dsb) and cell killing were used as criteria for radiation damage. Under aerobic conditions, BSO and DEM treatment gave a small sensitization of 10-20% for the 3 types of radiation damage. Also under severely hypoxic conditions (0.01 μM oxygen in the medium) the sensitizing effect of both compounds on the induction of ssb and dsb and on cell killing was small (0-30%). At somewhat higher concentrations of oxygen (0.5-10 μM) however, the sensitization amounted to about 90% for the induction of ssb and dsb and about 50% for cell killing. These results strengthen the widely accepted idea that intracellular SH-compounds compete with oxygen and other electron-affinic radiosensitizers with respect to reaction with radiation-induced damage, thus preventing the fixation of DNA damages by oxygen. These results imply that the extent to which SH-compounds affect the radiosensitivity of cells in vivo depends strongly on the local concentration of oxygen. (Auth.)

Erosion behaviour of physically vapour-deposited and chemically vapour-deposited SiC films coated on molybdenum during oxygenated argon beam thinning

International Nuclear Information System (INIS)

Shikama, T.; Kitajima, M.; Fukutomi, M.; Okada, M.

1984-01-01

The erosion behaviour during bombardment with a 5 keV argon beam at room temperature was studied for silicon carbide (SiC) films of thickness of about 10 μm coated on molybdenum by physical vapour deposition (PVD) and chemical vapour deposition (CVD). The PVD SiC (plasma-assisted ion plating) exhibited a greater thinning rate than the CVD SiC film. Electron probe X-ray microanalysis revealed that the chemical composition of PVD SiC was changed to a composition enriched in silicon by the bombardment, and there was a notable change in its surface morphology. The CVD SiC retained its initial chemical composition with only a small change in its surface morphology. Auger electron spectroscopy indicated that silicon oxide was formed on the surface of PVD SiC by the bombardment. The greater thinning rate and easier change in chemical composition in PVD SiC could be attributed to its readier chemical reaction with oxygen due to its more non-uniform structure and weaker chemical bonding. Oxygen was present as one of the impurities in the argon beam. (Auth.)

Geochemical Indicators of the Carbonate Sedimentation Depositional Environments and Geodynamic Conditions in the East of the Middle Urals in the Kizelovian Time

Directory of Open Access Journals (Sweden)

S. A. Dub

2017-12-01

Full Text Available Geochemical characteristics of the limestones of Kizelovskian substage of the Eastern Urals zone (Rezh River, Middle Urals, such as carbon and oxygen isotopic composition, concentration of minor and trace elements, and redox value indicators, were studied in details. Based on the results of data interpretation and analysis of lithological features, it was assumed that carbonate deposits formed in shallow oxygen-rich environment with high bioproductivity warm water ecosystem, and within the isolated carbonate platform with a steady sinking territory. Some signs indicate that sedimentation during the Kizelovian time occurred in the inner lagoon of a large atoll. The Maldivian archipelago could be a contemporary analogue of the Rezhevskaya carbonate platform.

Molybdenum depletion around P-phases Ni-Cr-Mo-W weld metals

International Nuclear Information System (INIS)

Silva, Cleiton Carvalho; Miranda, Helio Cordeiro de; Farias, Jesualdo Pereira

2010-01-01

This work evaluated the local chemical composition in matrix/precipitate interface in a Ni-Cr-Mo-W alloy weld metals deposited on substrate of C-Mn steel. The microstructural characterization was carried out through optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS). The results had shown that the presence of secondary phases precipitates in the interdendritic region. Through SEM analysis were observed indications of depletion of Mo around these phases. These precipitates were identified as P-phase by TEM analysis. The Mo depletion indications were confirmed through EDS. The Mo depletion was a result of a reheating due to several welding heat cycles deposited to promote the coating layer. (author)

ANATOMY OF DEPLETED INTERPLANETARY CORONAL MASS EJECTIONS

Energy Technology Data Exchange (ETDEWEB)

Kocher, M.; Lepri, S. T.; Landi, E.; Zhao, L.; Manchester, W. B. IV, E-mail: mkocher@umich.edu [Department of Climate and Space Sciences and Engineering, University of Michigan, 2455 Hayward Street, Ann Arbor, MI 48109-2143 (United States)

2017-01-10

We report a subset of interplanetary coronal mass ejections (ICMEs) containing distinct periods of anomalous heavy-ion charge state composition and peculiar ion thermal properties measured by ACE /SWICS from 1998 to 2011. We label them “depleted ICMEs,” identified by the presence of intervals where C{sup 6+}/C{sup 5+} and O{sup 7+}/O{sup 6+} depart from the direct correlation expected after their freeze-in heights. These anomalous intervals within the depleted ICMEs are referred to as “Depletion Regions.” We find that a depleted ICME would be indistinguishable from all other ICMEs in the absence of the Depletion Region, which has the defining property of significantly low abundances of fully charged species of helium, carbon, oxygen, and nitrogen. Similar anomalies in the slow solar wind were discussed by Zhao et al. We explore two possibilities for the source of the Depletion Region associated with magnetic reconnection in the tail of a CME, using CME simulations of the evolution of two Earth-bound CMEs described by Manchester et al.

Depositional Environment of the Sangkarewang Oil Shale, Ombilin Basin, Indonesia

Directory of Open Access Journals (Sweden)

Komang Anggayana

2014-12-01

Full Text Available Five samples from 56 m long drill core of lacustrine Sangkarewang oil shale have been studied by means of petrography and organic geochemistry to investigate the organic matter composition and depositional environments of the shale. The organic matter consists of abundant lamalginite (30%, v/v and very limited amount of vitrinite, suggesting aquatic depositional environments with minor terrestrial influence. Organic geochemical analysis exhibits the dominance of pristane, phytane, and generally n-alkanes compounds. These compounds might originate mostly from aquatic photosynthetic organisms. The oil shale was likely deposited in anoxic lake environments, suggested by the presence of framboidal pyrite (6%, v/v and preserved organic matter with total organic carbon (TOC about 4.9%. The pristane/phytane ratio is relatively high about 3.9 and thought as source sensitive rather than redox sensitive. Hopanoid and aryl isoprenoid compounds are present in minor amounts. The latter compounds are interpreted to be derived from green sulfur bacteria dwelling in anoxic and the presence of H2S in bottom water.

Corrosion of aluminium in copper-aluminium couples under a marine environment: Influence of polyaniline deposited onto copper

International Nuclear Information System (INIS)

Vera, Rosa; Verdugo, Patricia; Orellana, Marco; Munoz, Eduardo

2010-01-01

Research highlights: → The presence of Polyaniline in the Al-Cu system produces a decrease in the oxygen reduction reaction. → In the marine enviroment, aluminium in Al-Cu couples, suffers pitting and exfoliation. → The aluminium deterioration increases with chloride and enviromental sulphur dioxide presence, mainly when it is united to bare copper. - Abstract: In this study, we examined how aluminium corrosion in Al-Cu/PANI galvanic couples in a marine environment is influenced by deposition of polyaniline (PANI) on copper. Polarization curves and immersion assays in 0.1 M NaCl were performed. The morphologies of etched Al and corrosion products were observed by SEM, and the Al ions in solution were quantified by atomic absorption spectroscopy. A reduction in aluminium damage due to galvanic corrosion was observed as a result of decreased effective area for the oxygen reduction reaction on Cu/PANI electrode. Furthermore, an electrochemical reduction of PANI from leucoemeraldine to emeraldine base is proposed.

The role of oxygen in CdS/CdTe solar cells deposited by close-spaced sublimation

Energy Technology Data Exchange (ETDEWEB)

Rose, D.H.; Levi, D.H.; Matson, R.J. [National Renewable Energy Lab., Golden, CO (United States)] [and others

1996-05-01

The presence of oxygen during close-spaced sublimation (CSS) of CdTe has been previously reported to be essential for high-efficiency CdS/CdTe solar cells because it increases the acceptor density in the absorber. The authors find that the presence of oxygen during CSS increases the nucleation site density of CdTe, thus decreasing pinhole density and grain size. Photoluminescence showed that oxygen decreases material quality in the bulk of the CdTe film, but positively impacts the critical CdS/CdTe interface. Through device characterization the authors were unable to verify an increase in acceptor density with increased oxygen. These results, along with the achievement of high-efficiency cells (13% AM1.5) without the use of oxygen, led the authors to conclude that the use of oxygen during CSS deposition of CdTe can be useful but is not essential.

The Toxicity of Depleted Uranium

Directory of Open Access Journals (Sweden)

Wayne Briner

2010-01-01

Full Text Available Depleted uranium (DU is an emerging environmental pollutant that is introduced into the environment primarily by military activity. While depleted uranium is less radioactive than natural uranium, it still retains all the chemical toxicity associated with the original element. In large doses the kidney is the target organ for the acute chemical toxicity of this metal, producing potentially lethal tubular necrosis. In contrast, chronic low dose exposure to depleted uranium may not produce a clear and defined set of symptoms. Chronic low-dose, or subacute, exposure to depleted uranium alters the appearance of milestones in developing organisms. Adult animals that were exposed to depleted uranium during development display persistent alterations in behavior, even after cessation of depleted uranium exposure. Adult animals exposed to depleted uranium demonstrate altered behaviors and a variety of alterations to brain chemistry. Despite its reduced level of radioactivity evidence continues to accumulate that depleted uranium, if ingested, may pose a radiologic hazard. The current state of knowledge concerning DU is discussed.

Analysis of Atmospheric Nitrate Deposition in Lake Tahoe Using Multiple Oxygen Isotopes

Science.gov (United States)

McCabe, J. R.; Michalski, G. M.; Hernandez, L. P.; Thiemens, M. H.; Taylor, K.; Kendall, C.; Wankel, S. D.

2002-12-01

Lake Tahoe in the Sierra Nevada Mountain Range is world renown for its depth and water clarity bringing 2.2 million visitors per year resulting in annual revenue of \\1.6 billion from tourism. In past decades the lake has suffered from decreased water clarity (from 32 m plate depth to less than 20), which is believed to be largely the result of algae growth initiated by increased nutrient loading. Lake nutrients have also seen a shift from a nitrogen limited to a phosphorous limited system indicating a large increase in the flux of fixed nitrogen. Several sources of fixed nitrogen of have been suggested including surface runoff, septic tank seepage from ground water and deposition from the atmosphere. Bio-available nitrogen in the form of nitrate (NO_{3}$-) is a main component of this system. Recent studies have estimated that approximately 50% of the nitrogen input into the lake is of atmospheric origin (Allison et al. 2000). However, the impact and magnitude of atmospheric deposition is still one of the least understood aspects of the relationship between air and water quality in the Basin (TRPA Threshold Assessment 2002). The utility of stable isotopes as tracers of nitrate reservoirs has been shown in several studies (Bohlke et al. 1997, Kendall and McDonnell 1998, Durka et al. 1994). Stable nitrogen (δ15N) and oxygen (δ18O) isotopes have been implemented in a dual isotope approach to characterize the various nitrate sources to an ecosystem. While δ18O distinguishes between atmospheric and soil sources of nitrate, processes such as denitrification can enrich the residual nitrate in δ18O leaving a misleading atmospheric signature. The benefit of δ15N as a tracer for NO3- sources is the ability to differentiate natural soil, fertilizer, and animal or septic waste, which contain equivalent δ18O values. The recent implementation of multiple oxygen isotopes to measure Δ17O in nitrate has proven to be a more sensitive tracer of atmospheric deposition. The

Systemic depletion of L-cyst(e)ine with cyst(e)inase increases reactive oxygen species and suppresses tumor growth.

Science.gov (United States)

Cramer, Shira L; Saha, Achinto; Liu, Jinyun; Tadi, Surendar; Tiziani, Stefano; Yan, Wupeng; Triplett, Kendra; Lamb, Candice; Alters, Susan E; Rowlinson, Scott; Zhang, Yan Jessie; Keating, Michael J; Huang, Peng; DiGiovanni, John; Georgiou, George; Stone, Everett

2017-01-01

Cancer cells experience higher oxidative stress from reactive oxygen species (ROS) than do non-malignant cells because of genetic alterations and abnormal growth; as a result, maintenance of the antioxidant glutathione (GSH) is essential for their survival and proliferation. Under conditions of elevated ROS, endogenous L-cysteine (L-Cys) production is insufficient for GSH synthesis. This necessitates uptake of L-Cys that is predominantly in its disulfide form, L-cystine (CSSC), via the xCT(-) transporter. We show that administration of an engineered and pharmacologically optimized human cyst(e)inase enzyme mediates sustained depletion of the extracellular L-Cys and CSSC pool in mice and non-human primates. Treatment with this enzyme selectively causes cell cycle arrest and death in cancer cells due to depletion of intracellular GSH and ensuing elevated ROS; yet this treatment results in no apparent toxicities in mice even after months of continuous treatment. Cyst(e)inase suppressed the growth of prostate carcinoma allografts, reduced tumor growth in both prostate and breast cancer xenografts and doubled the median survival time of TCL1-Tg:p53 -/- mice, which develop disease resembling human chronic lymphocytic leukemia. It was observed that enzyme-mediated depletion of the serum L-Cys and CSSC pool suppresses the growth of multiple tumors, yet is very well tolerated for prolonged periods, suggesting that cyst(e)inase represents a safe and effective therapeutic modality for inactivating antioxidant cellular responses in a wide range of malignancies.

Base cation depletion and potential long-term acidification of Norwegian catchments

International Nuclear Information System (INIS)

Kirchner, J.W.; Lydersen, E.

1995-01-01

Long-term monitoring data from Norwegian catchments show that since the late 1970s, sulfate deposition and runoff sulfate concentrations have declined significantly. However, water quality has not significantly improved, because reductions in runoff sulfate have been matched by equal declines in calcium and magnesium concentrations. Long-term declines in runoff Ca and Mg are most pronounced at catchments subject to highly acidic deposition; the observed rates of decline are quantitatively consistent with depletion of exchangeable bases by accelerated leaching under high acid loading. Even though water quality has not recovered, reductions in acid deposition have been valuable because they have prevented significant acidification that would otherwise have occurred under constant acid deposition. Ongoing depletion of exchangeable bases from these catchments implies that continued deposition reductions will be needed to avoid further acidification and that recovery from acidification will be slow. 31 refs., 2 figs., 4 tabs

An oxygen isotope study on hydrothermal sources of granite-type uranium deposits in South China

International Nuclear Information System (INIS)

Yongfei, Z.

1987-01-01

The usefulness of oxygen isotope measurements in solving problems of hydrothermal sources has been demonstrated in a number of detailed studies of the granite type uranium deposits in this paper. Remarkly the granite-type uranium deposits in Southr China have been shown to have formed from magmatic water, meteoric water, of mixtures of both the above, and origin of waters in the ore-forming fluid may be different for differing uranium deposits ore differing stages of the mineralization. Consequences obtained in this study for typical uranium deposits of different age and geologic sitting agree well with that obtained by other geologic-geochemical investigation. Furthermore, not only meteoric water is of importance to origin and evolution of the ore-forming fluid, but also mixing of waters from different sources is considered to be one of the most characteristic features of many hydrothermal uranium deposits related to granitoids or volcanics. (C.D.G.) [pt

The role of oxygen in the uptake of deuterium in lithiated graphite

Energy Technology Data Exchange (ETDEWEB)

Taylor, C. N.; Luitjohan, K. E. [School of Nuclear Engineering, Purdue University, West Lafayette, Indiana 47907 (United States); Dadras, J. [Department of Physics and Astronomy, University of Tennessee, Knoxville, Tennessee 37998 (United States); Allain, J. P. [School of Nuclear Engineering, Purdue University, West Lafayette, Indiana 47907 (United States); Birck Nanotechnology Center, West Lafayette, Indiana 47907 (United States); Krstic, P. S. [Department of Physics and Astronomy, University of Tennessee, Knoxville, Tennessee 37998 (United States); Joint Institute of Computational Sciences, University of Tennessee, Knoxville, Tennessee 37998 (United States); Physics Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Skinner, C. H. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States)

2013-12-14

We investigate the mechanism of deuterium retention by lithiated graphite and its relationship to the oxygen concentration through surface sensitive experiments and atomistic simulations. Deposition of lithium on graphite yielded 5%–8% oxygen surface concentration and when subsequently irradiated with D ions at energies between 500 and 1000 eV/amu and fluences over 10{sup 16} cm{sup −2} the oxygen concentration rose to between 25% and 40%. These enhanced oxygen levels were reached in a few seconds compared to about 300 h when the lithiated graphite was allowed to adsorb oxygen from the ambient environment under equilibrium conditions. Irradiating graphite without lithium deposition, however, resulted in complete removal of oxygen to levels below the detection limit of XPS (e.g., <1%). These findings confirm the predictions of atomistic simulations, which had concluded that oxygen was the primary component for the enhanced hydrogen retention chemistry on the lithiated graphite surface.

Oxidation behavior of V-Cr-Ti alloys in low-partial-pressure oxygen environments

International Nuclear Information System (INIS)

Natesan, K.; Uz, M.

1998-01-01

A test program is in progress at Argonne National Laboratory to evaluate the effect of pO 2 in the exposure environment on oxygen uptake, scaling kinetics, and scale microstructure in V-Cr-Ti alloys. The data indicate that the oxidation process follows parabolic kinetics in all of the environments used in the present study. From the weight change data, parabolic rate constants were evaluated as a function of temperature and exposure environment. The temperature dependence of the parabolic rate constants was described by an Arrhenius relationship. Activation energy for the oxidation process was fairly constant in the oxygen pressure range of 1 x 10 -6 to 1 x 10 -1 torr for both the alloys. The activation energy for oxidation in air was significantly lower than in low-pO 2 environments, and for oxidation in pure O 2 at 760 torr was much lower than in low-pO 2 environments. X-ray diffraction analysis of the specimens showed that VO 2 was the dominant phase in low-pO 2 environments, while V 2 O 5 was dominant in air and in pure oxygen at 76f0 torr

Depleted uranium - influence on the health and environment; Ochudobneny uran - vplyva na zdravie a zivotne prostredie

Energy Technology Data Exchange (ETDEWEB)

Rosskopfova, O [Katedra jadrovej chemie, Prirodovedecka fakulta, Univerzita Komenskeho, Bratislava (Slovakia)

2002-07-01

The uranium as radioactive element occurs in low concentrations in all components of environment. In the sample of natural uranium the isotope U-235 has the highest share (99.27 weight per cent). Chemical toxicity of uranium is comparable with toxicity of the elements like As and Pb. Depleted uranium is adjoining product in the production of enriched uranium, which is required in the production of the nuclear fuel and in the production of material used in nuclear arms. It mainly includes isotope U-238, and the content of isotopes U-235 and U-234 is sharply lowered. According to NRC depleted uranium is defined like uranium, in which percentile share of isotope U-235 is less than 0.711 weight percent. The activity of depleted uranium from viewpoint of external irradiation does not represent higher risk. Much higher risk for man represent the neurotoxic effects of uranium, which can get into human body by inhaling of dispersed particles, of contaminated dust and aerosols from atmosphere or by consumption of contaminated foodstuffs and water. Basic dangerous of irradiation by depleted uranium are mainly aerosols, which increase the probability of occurrence of lung cancer. The next dangerous is the damage of another organs like kidneys, liver and bones, where these aerosols are transported by blood like oxides from the lungs. In the environmental parts because of presence of natural uranium the depleted uranium is difficultly identifiably by standard detective methods. Thus it is necessary to use suitable radiochemical separative methods in combination with suitable detective method. (author)

Phylogenetic analyses and nitrate-reducing activity of fungal cultures isolated from the permanent, oceanic oxygen minimum zone of the Arabian Sea

Digital Repository Service at National Institute of Oceanography (India)

Manohar, C.S; Menezes, L.D.; Ramasamy, K.P.; Meena, R.M.

of the oxygen-depleted environments is less than that of mangrove regions and deep-sea habitats. Phylogenetic analyses of 18S rRNA sequences revealed a few divergent isolates that clustered with environmental sequences previously obtained by others...

Energizing and depletion of neutrals by a collisional plasma

International Nuclear Information System (INIS)

Fruchtman, A

2008-01-01

Neutral depletion can significantly affect the steady state of low temperature plasmas. Recent theoretical analyses predicted previously unexpected effects of neutral depletion in both collisional and collisionless regimes. In this paper we address the effect of the energy deposited in the neutral gas by a collisional plasma. The fraction of power deposited in the neutrals is shown to be independent of the amount of power. The first case we address is of a thermalized neutral gas. It is shown that a low heat conductivity of the neutral gas is followed by a high neutral temperature that results in a high neutral depletion even if the plasma pressure is small. In the second case neutrals are accelerated through charge exchange with ions leading to what we call neutral pumping, which is equivalent to ion pumping in a collisionless plasma. Neutral depletion is found in the second case for both a closed system (no net mass flow) and an open system (a finite mass flow). A thruster that employs a collisional plasma and pumped neutrals is compared with the thruster analyzed before that employs collisionless plasma.

Visible photoluminescence from plasma-polymerized-organosilicone thin films deposited from HMDSO/O2 induced remote plasma: effect of oxygen fraction

International Nuclear Information System (INIS)

Naddaf, M.; Saloum, S.

2009-01-01

Visible photoluminescence (PL) from thin films deposited on silicon wafers by remote plasma polymerization of the hexamethyldisiloxane (HMDSO)/O 2 mixture in a radio-frequency hollow cathode discharge reactor has been investigated as a function of different oxygen fractions (χ0 2 0.38, 0.61, 0.76 and 0.9). At room temperature, the film deposited at exhibits a strong, broad PL band peak centred at around 537.6 nm. A blue shift and a considerable decrease (∼one order) in the intensity of the PL peak are observed after the addition of oxygen. Furthermore, in contrast to the film deposited from pure HMDSO, the low temperature (15 K) PL spectra of the film deposited from different HMDSO/O 2 mixtures exhibit two separated green-blue and yellow-green PL peaks. The PL behaviour of the deposited films is correlated with their structural and morphological properties, investigated by using Fourier transform infrared, atomic force microscope and contact angle techniques. In addition, it is found from spectrophotometry measurements that the deposited films have relatively low absorption coefficients (in the range 100-500 cm -1 ) in the spectral range of their PL emission, attractive for possible integrated optics devices. (authors)

Triple oxygen isotopes indicate urbanization affects sources of nitrate in wet and dry atmospheric deposition

Science.gov (United States)

Nelson, David M.; Tsunogai, Urumu; Ding, Dong; Ohyama, Takuya; Komatsu, Daisuke D.; Nakagawa, Fumiko; Noguchi, Izumi; Yamaguchi, Takashi

2018-05-01

Atmospheric nitrate deposition resulting from anthropogenic activities negatively affects human and environmental health. Identifying deposited nitrate that is produced locally vs. that originating from long-distance transport would help inform efforts to mitigate such impacts. However, distinguishing the relative transport distances of atmospheric nitrate in urban areas remains a major challenge since it may be produced locally and/or be transported from upwind regions. To address this uncertainty we assessed spatiotemporal variation in monthly weighted-average Δ17O and δ15N values of wet and dry nitrate deposition during one year at urban and rural sites along the western coast of the northern Japanese island of Hokkaido, downwind of the East Asian continent. Δ17O values of nitrate in wet deposition at the urban site mirrored those of wet and dry deposition at the rural site, ranging between ˜ +23 and +31 ‰ with higher values during winter and lower values in summer, which suggests the greater relative importance of oxidation of NO2 by O3 during winter and OH during summer. In contrast, Δ17O values of nitrate in dry deposition at the urban site were lower (+19 - +25 ‰) and displayed less distinct seasonal variation. Furthermore, the difference between δ15N values of nitrate in wet and dry nitrate deposition was, on average, 3 ‰ greater at the urban than rural site, and Δ17O and δ15N values were correlated for both forms of deposition at both sites with the exception of dry deposition at the urban site. These results suggest that, relative to nitrate in wet and dry deposition in rural environments and wet deposition in urban environments, nitrate in dry deposition in urban environments forms from relatively greater oxidation of NO by peroxy radicals and/or oxidation of NO2 by OH. Given greater concentrations of peroxy radicals and OH in cities, these results imply that dry nitrate deposition results from local NOx emissions more so than wet

Efficiency of Photosynthesis in a Chl d-Utilizing Cyanobacterium is Comparable to or Higher than that in Chl a-Utilizing Oxygenic Species

Science.gov (United States)

Mielke, S. P.; Kiang, N. Y.; Blankenship, R. E.; Gunner, M. R.; Mauzerall, D.

2011-01-01

The cyanobacterium Acaryochloris marina uses chlorophyll d to carry out oxygenic photosynthesis in environments depleted in visible and enhanced in lower-energy, far-red light. However, the extent to which low photon energies limit the efficiency of oxygenic photochemistry in A. marina is not known. Here, we report the first direct measurements of the energy-storage efficiency of the photosynthetic light reactions in A. marina whole cells,and find it is comparable to or higher than that in typical, chlorophyll a-utilizing oxygenic species. This finding indicates that oxygenic photosynthesis is not fundamentally limited at the photon energies employed by A. marina, and therefore is potentially viable in even longer-wavelength light environments.

Assessment of the oxygen consumption in the backfill. Geochemical modelling in a saturated backfill

International Nuclear Information System (INIS)

Grandia, Fidel; Domenech, Cristina; Arcos, David; Duro, Lara

2006-11-01

The consumption of oxygen in the deep disposal is a major concern due to the ability of this element to corrode the canisters where high level nuclear wastes (HLNW) are disposed. The anoxic conditions initially present in a deep geologic environment are disturbed by the excavation of the repository facilities. After sealing the deposition holes and tunnels using clay-based materials, oxygen remains dissolved in porewater or as a gas phase in the unsaturated pores. The main mechanisms of oxygen depletion that can be considered in the backfill materials are: (1) diffusion into the surrounding rock and (2) kinetic reactions with accessory minerals and organic matter existing in the backfill. In this report, a set of numerical simulations are carried out in one and two dimensions in order to test the effect on the oxygen concentration in the pore water of all these mechanisms. The backfill considered is a 0/70 mixture of MX-80 bentonite and crushed material from the excavation itself. In addition to organic matter, the solid phases with reducing capacity in the backfill are Fe(II)-bearing minerals: pyrite (FeS 2 ) and siderite (FeCO) (as accessory minerals in the bentonite) and Fe-biotite (from the crushed granite). In the simulations, other chemical processes like cation exchange and surface complexation onto clay surfaces, and thermodynamic equilibrium with calcite, gypsum and quartz are considered. Initial composition of porewater is obtained by equilibrating the Forsmark groundwater with the backfill material. The 1D simulation consists of a number of cells with no reactive minerals or organic matter representing granite. The central cell, however, contains oxygen and reactive minerals resembling a backfill. Oxygen is allowed to move only by diffusion. The 2D model simulates the interaction with a backfill of a granitic groundwater flowing through a fracture. Like in the 1D model, the backfill contains oxygen and reactive solids. The results are very similar in

Assessment of the oxygen consumption in the backfill. Geochemical modelling in a saturated backfill

Energy Technology Data Exchange (ETDEWEB)

Grandia, Fidel; Domenech, Cristina; Arcos, David; Duro, Lara [Enviros Spain S.L., Barcelona (Spain)

2006-11-15

The consumption of oxygen in the deep disposal is a major concern due to the ability of this element to corrode the canisters where high level nuclear wastes (HLNW) are disposed. The anoxic conditions initially present in a deep geologic environment are disturbed by the excavation of the repository facilities. After sealing the deposition holes and tunnels using clay-based materials, oxygen remains dissolved in porewater or as a gas phase in the unsaturated pores. The main mechanisms of oxygen depletion that can be considered in the backfill materials are: (1) diffusion into the surrounding rock and (2) kinetic reactions with accessory minerals and organic matter existing in the backfill. In this report, a set of numerical simulations are carried out in one and two dimensions in order to test the effect on the oxygen concentration in the pore water of all these mechanisms. The backfill considered is a 0/70 mixture of MX-80 bentonite and crushed material from the excavation itself. In addition to organic matter, the solid phases with reducing capacity in the backfill are Fe(II)-bearing minerals: pyrite (FeS{sub 2}) and siderite (FeCO) (as accessory minerals in the bentonite) and Fe-biotite (from the crushed granite). In the simulations, other chemical processes like cation exchange and surface complexation onto clay surfaces, and thermodynamic equilibrium with calcite, gypsum and quartz are considered. Initial composition of porewater is obtained by equilibrating the Forsmark groundwater with the backfill material. The 1D simulation consists of a number of cells with no reactive minerals or organic matter representing granite. The central cell, however, contains oxygen and reactive minerals resembling a backfill. Oxygen is allowed to move only by diffusion. The 2D model simulates the interaction with a backfill of a granitic groundwater flowing through a fracture. Like in the 1D model, the backfill contains oxygen and reactive solids. The results are very similar in

A thermoluminescence study of vempalle dolomites and its depositional environments

International Nuclear Information System (INIS)

Bhattacharya, A.K.; Rao, C.N.; Kaul, I.K.

1976-01-01

An attempt has been made to interpret the depositional environment of Vempalle dolomites (India) by thermoluminescence method. It has been demonstrated that glow curve patterns reflect the environmental condition of deposition for carbonate sediments. The glow curves were obtained for natural samples as well as samples irradiated by Co 60 and compared. A majority of the samples were concluded to be diagenetic. (A.K.)

Modelling long-term redox processes and oxygen scavenging in fractured crystalline rocks

International Nuclear Information System (INIS)

Sidborn, Magnus

2007-10-01

the reducing minerals in the rock was shown to be the flow-wetted surface to flow-rate ratio. The results show that for an initial period of time, depending on the amount of reducing minerals and reaction rates, chemical reaction kinetics may control the rate of the overall depletion of oxygen. For longer times, internal diffusion resistance in large particles or in the rock matrix become rate limiting for the overall process. It was found that there are many uncertainties that have to be considered in order to make reliable quantitative predictions on the extent of oxygen intrusion. In the second part of the thesis, the impact of intruding oxygen on the corrosion of the copper canisters was explored. Also, a mechanism for the production of sulphide close to the deposition holes was studied. Sulphide is another corroding agent that may be produced microbially in a reducing environment from sulphate in the presence of organic reductants such as methane. From calculation results it was found that corrosion of more than 50 kg of copper is not likely over a period of one million years

Geochemical characteristics of The Emet (Espey-Hisarcik) borate deposits, Kütahya, Turkey

Science.gov (United States)

Koçak, İ.; Koç, Ş.

2018-06-01

Nearly 72% world's borate reserves are in western part of Turkey. The Emet (Kütahya) deposit is one of these deposits. The Emet borate deposit, like other deposits in western Anatolia, was deposited in Miocene lacustrine environment whose formation coincides with volcanic activity started in Paleogene and lasted to the beginning of Quaternary. The borate ore displaying lenticular structure is alternated with claystone, marl, tuff and thin bedded limestone. The mineral paragenesis is composed of colemanite, hydroboracite, Veatchite, dolomite, calcite, montmorillonite and illite. The Emet borate deposit has been the subject of various geologic and mineralogical studies. In the present study major and trace element contents of 60 borate samples from this deposit are discussed. Among the trace elements, significant enrichment was found in As, Se, Sr, Cs, Sb and Li. Element correlations indicate volcanic source for boron (exhalations and hydrothermal solutions) whilst other elements are found to be derived from a terrestrial source. According to REE data, high Ce concentrations and anomalies are generally indicative of oxygenated depositional environment whilst low Ce contents facilitated the lake waters to be low oxygenated as a result of H2S-rich hydrothermal solutions. The weak negative anomaly detected only in the Hisarcık region is attributed to lacking of Eu contribution to the lake due to insufficient alteration on the continent.

Effects of the oxygen fraction and substrate bias power on the electrical and optical properties of silicon oxide films by plasma enhanced chemical vapour deposition using TMOS/O2 gas

International Nuclear Information System (INIS)

Bang, S B; Chung, T H; Kim, Y; Kang, M S; Kim, J K

2004-01-01

Thin oxide films are deposited from tetramethoxysilane in an inductively coupled oxygen glow discharge supplied with radio frequency power. The chemical bonding states of deposited films are analysed by Fourier transform infrared spectroscopy. The deposition rate and optical properties are determined from spectroscopic ellipsometry. Capacitance-voltage measurements are performed in MOS capacitors to obtain the electrical properties of the deposited films. With these tools, the effects of the substrate bias power and the oxygen mole fraction in the gas on the properties of the film are investigated. The refractive index first decreases with an increase in the oxygen mole fraction, and then increases again, showing a behaviour opposite to that of the deposition rate. The deposition rate increases with increasing substrate bias power and then saturates, while the refractive index increases slightly with an increase in the substrate bias power. The fixed oxide charge density decreases with increasing oxygen fraction and with increasing substrate bias power, while the interface trap density increases with increasing oxygen fraction and with increasing substrate bias power

Oxygen reduction activity of N-doped carbon-based films prepared by pulsed laser deposition

Science.gov (United States)

Hakoda, Teruyuki; Yamamoto, Shunya; Kawaguchi, Kazuhiro; Yamaki, Tetsuya; Kobayashi, Tomohiro; Yoshikawa, Masahito

2010-12-01

Carbon-based films with nitrogen species on their surface were prepared on a glassy carbon (GC) substrate for application as a non-platinum cathode catalyst for polymer electrolyte fuel cells. Cobalt and carbon were deposited in the presence of N 2 gas using a pulsed laser deposition method and then the metal Co was removed by HCl-washing treatment. Oxygen reduction reaction (ORR) activity was electrochemically determined using a rotating disk electrode system in which the film samples on the GC substrate were replaceable. The ORR activity increased with the temperature of the GC substrate during deposition. A carbon-based film prepared at 600 °C in the presence of N 2 at 66.7 Pa showed the highest ORR activity among the tested samples (0.66 V vs. NHE). This film was composed of amorphous carbons doped with pyridine type nitrogen atoms on its surface.

Quantification of amyloid deposits and oxygen extraction fraction in the brain with multispectral optoacoustic imaging in arcAβ mouse model of Alzheimer's disease

Science.gov (United States)

Ni, Ruiqing; Vaas, Markus; Rudin, Markus; Klohs, Jan

2018-02-01

Beta-amyloid (Aβ) deposition and vascular dysfunction are important contributors to the pathogenesis in Alzheimer's disease (AD). However, the spatio-temporal relationship between an altered oxygen metabolism and Aβ deposition in the brain remains elusive. Here we provide novel in-vivo estimates of brain Aβ load with Aβ-binding probe CRANAD-2 and measures of brain oxygen saturation by using multi-spectral optoacoustic imaging (MSOT) and perfusion imaging with magnetic resonance imaging (MRI) in arcAβ mouse models of AD. We demonstrated a decreased cerebral blood flow (CBF) and cerebral metabolic rate of oxygen (CMRO2) in the cortical region of the arcAβ mice compared to wildtype littermates at 24 months. In addition, we showed proof-of-concept for the detection of cerebral Aβ deposits in brain from arcAβ mice compared to wild-type littermates.

Effect of oxygen pressure on the structure and luminescence of Eu-doped Gd{sub 2}O{sub 3} thin films

Energy Technology Data Exchange (ETDEWEB)

Wellenius, Patrick; Muth, John F. [Department of Electrical and Computer Engineering, NC State University, Raleigh, NC 27606 (United States); Smith, Eric R. [Kratos Defense and Security Solutions, Inc., 5030 Bradford Dr., Huntsville, AL 35805 (United States); Wu, Pae C [Department of Electrical and Computer Engineering, Duke University, Durham, NC 27708 (United States); Everitt, Henry O. [Department of Electrical and Computer Engineering, Duke University, Durham, NC 27708 (United States); Army Aviation and Missile RD and E Center, Redstone Arsenal, AL 35898 (United States)

2010-08-15

Europium-doped gadolinium oxide (Gd{sub 2}O{sub 3}) thin films were deposited on sapphire substrates by pulsed laser deposition (PLD). The effect of oxygen pressure during deposition on the structure of the thin films, investigated by transmission electron microscopy (TEM) and X-ray diffraction (XRD), was correlated to photoluminescence spectra. The polycrystalline films, like the one deposited in 5 mTorr oxygen environment, were primarily monoclinic phase; however the rarer cubic phase was achieved at 50 mTorr pressure. Time-integrated and time-resolved photoluminescence (TIPL and TRPL) spectra of the bright {sup 5}D{sub 0} to {sup 7}F{sub 2} radiative transition revealed how the differing host material phases altered the local environment of the Eu dopants. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

Visible photoluminescence from plasma-polymerized-organosilicone thin films deposited from HMDSO/O2 induced remote plasma: effect of oxygen fraction

Science.gov (United States)

Naddaf, M.; Saloum, S.

2008-09-01

Visible photoluminescence (PL) from thin films deposited on silicon wafers by remote plasma polymerization of the hexamethyledisiloxane (HMDSO)/O2 mixture in a radio-frequency hollow cathode discharge reactor has been investigated as a function of different oxygen fractions ( \\chi _{O_2 } =0 , 0.38, 0.61, 0.76 and 0.9). At room temperature, the film deposited at \\chi _{O_2 } =0 exhibits a strong, broad PL band peak centred at around 537.6 nm. A blue shift and a considerable decrease (~one order) in the intensity of the PL peak are observed after the addition of oxygen. Furthermore, in contrast to the film deposited from pure HMDSO, the low temperature (15 K) PL spectra of the film deposited from different HMDSO/O2 mixtures exhibit two separated 'green-blue' and 'yellow-green' PL peaks. The PL behaviour of the deposited films is correlated with their structural and morphological properties, investigated by using Fourier transform infrared, atomic force microscope and contact angle techniques. In addition, it is found from spectrophotometry measurements that the deposited films have relatively low absorption coefficients (in the range 100-500 cm-1) in the spectral range of their PL emission, attractive for possible integrated optics devices.

Visible photoluminescence from plasma-polymerized-organosilicone thin films deposited from HMDSO/O2 induced remote plasma: effect of oxygen fraction

International Nuclear Information System (INIS)

Naddaf, M; Saloum, S

2008-01-01

Visible photoluminescence (PL) from thin films deposited on silicon wafers by remote plasma polymerization of the hexamethyledisiloxane (HMDSO)/O 2 mixture in a radio-frequency hollow cathode discharge reactor has been investigated as a function of different oxygen fractions (χ O 2 =0, 0.38, 0.61, 0.76 and 0.9). At room temperature, the film deposited at (χ O 2 =0 exhibits a strong, broad PL band peak centred at around 537.6 nm. A blue shift and a considerable decrease (∼one order) in the intensity of the PL peak are observed after the addition of oxygen. Furthermore, in contrast to the film deposited from pure HMDSO, the low temperature (15 K) PL spectra of the film deposited from different HMDSO/O 2 mixtures exhibit two separated 'green-blue' and 'yellow-green' PL peaks. The PL behaviour of the deposited films is correlated with their structural and morphological properties, investigated by using Fourier transform infrared, atomic force microscope and contact angle techniques. In addition, it is found from spectrophotometry measurements that the deposited films have relatively low absorption coefficients (in the range 100-500 cm -1 ) in the spectral range of their PL emission, attractive for possible integrated optics devices

Analysing impact of oxygen and water exposure on roll-coated organic solar cell performance using impedance spectroscopy

DEFF Research Database (Denmark)

Arredondo, B.; Romero, B.; Beliatis, M. J.

2018-01-01

In this work we study the degradation of roll-coated flexible inverted organic solar cells in different atmospheres. We demonstrate that impedance spectroscopy is a powerful tool for elucidating degradation mechanisms; it is used here to distinguish the different degradation mechanisms due to water...... and oxygen. Identical cells were exposed to different accelerated degradation environments using water only, oxygen only, and both water and oxygen simultaneously, all of them enhanced with UV light. The photocurrent is dramatically reduced in the oxygen-degraded samples. Impedance measurements indicate...... of degradation differs for the water and oxygen degraded samples. While oxygen + UV light decreases the conductivity of the PEDOT:PSS layer, water + UV light changes the PEDOT:PSS work function inducing a depletion region at the anode....

Oxygen Reduction Reaction on Pt Overlayers Deposited onto a Gold Film: Ligand, Strain, and Ensemble Effect

DEFF Research Database (Denmark)

Deng, Yu-Jia; Tripkovic, Vladimir; Rossmeisl, Jan

2016-01-01

We study the oxygen reduction reaction (ORR), the catalytic process occurring at the cathode in fuel cells, on Pt layers prepared by electrodeposition onto an Au substrate. Using a nominal Pt layer by layer deposition method previously proposed, imperfect layers of Pt on Au are obtained. The ORR...

Effect of oxygen partial pressure on the microstructural, optical and gas sensing characterization of nanostructured Gd doped ceria thin films deposited by pulsed laser deposition

Directory of Open Access Journals (Sweden)

Nagaraju P.

2017-12-01

Full Text Available Microstructural properties of 10 mol% gadolinium doped ceria (CeO2 thin films that were deposited on quartz substrate at substrate temperature of 1023 K by using pulsed laser deposition with different oxygen partial pressures in the range of 50–200 mTorr. The influence of oxygen partial pressure on microstructural, morphological, optical and gas sensing characterization of the thin films was systematically studied. The microstructure of the thin films was investigated using X-ray diffraction, atomic force microscopy and Raman spectroscopy. Morphological studies have been carried out using scanning electron microscope. The experimental results confirmed that the films were polycrystalline in nature with cubic fluorite structure. Optical properties of the thin films were examined using UV–vis spectrophotometer. The optical band gap calculated from Tauc’s relation. Gas sensing characterization has been carried at different operating temperatures (room temperature to 523 K for acetone gas. Response and recovery times of the sensor were calculated using transient response plot.

Depositional environment of the Gombe Formation in the Gongola ...

African Journals Online (AJOL)

The depositional environment of the Gombe Formation was determined using grain size parameters in which sixteen sandstone samples and ninety nine pebbles were subjected to granulometric and pebbles morphometric analysis respectively. The granulometric analysis for the sixteen (16) samples of the Gombe ...

Sedimentary architecture and depositional environment of Kudat Formation, Sabah, Malaysia

Science.gov (United States)

Ghaheri, Samira; Suhaili, Mohd; Sapari, Nasiman; Momeni, Mohammadsadegh

2017-12-01

Kudat Formation originated from deep marine environment. Three lithofacies association of deep marine turbidity channel was discovered in three Members of the Kudat Formation in Kudat Peninsula, Sabah, Malaysia. Turbidite and deep marine architecture elements was described based on detailed sedimentological studies. Four architecture elements were identified based on each facies association and their lithology properties and character: inner external levee that was formed by turbidity flows spill out from their confinement of channel belt; Lobes sheet that was formed during downslope debris flows associated with levee; Channel fill which sediments deposited from high to low density currents with different value of sediment concentration; and overbank terrace which was formed by rapid suspension sedimentation. The depositional environment of Kudat Formation is shelf to deep marine fan.

Long distance electron transmission couples sulphur, iron, calcium and oxygen cycling in marine sediment

DEFF Research Database (Denmark)

Risgaard-Petersen, Nils; Nielsen, Lars Peter

sulfide oxidation leads to electric field formation, sulfide depletion and acidification of the upper centimeters of the sediment. This promoted ion migration and dissolution of carbonates and iron sulfides. Sulfide released from iron sulfides was the major e-donor in the system. Ferrous iron released...... from iron sulfides was to a large extend deposited in the oxic zone as iron oxides and Ca2+ eventually precipitates at the surface as due to high pH caused by cathodic oxygen reduction. The result show how long distance electron transmission allows oxygen to drive the allocation of important minerals...... geochemical alterations in the upper centimetres of the anoxic sediment: Sulphides were oxidized to sulphate in anoxic sediment layers. Electrons from this half-reaction were passed to the oxic layers cm above. In this way the domain of oxygen was extended far beyond it’s physically presence. Bioelectrical...

Influence of argon and oxygen pressure ratio on bipolar-resistive switching characteristics of CeO2- x thin films deposited at room temperature

Science.gov (United States)

Ismail, Muhammad; Ullah, Rehmat; Hussain, Riaz; Talib, Ijaz; Rana, Anwar Manzoor; Hussain, Muhammad; Mahmood, Khalid; Hussain, Fayyaz; Ahmed, Ejaz; Bao, Dinghua

2018-02-01

Cerium oxide (CeO2-x) film was deposited on Pt/Ti/SiO2/Si substrate by rf magnetron sputtering at room temperature. Resistive switching characteristics of these ceria films have been improved by increasing oxygen content during deposition process. Endurance and statistical analyses indicate that the operating stability of CeO2-x-based memory is highly dependent on the oxygen content. Results indicate that CeO2-x film-based RRAM devices exhibit optimum performance when fabricated at an argon/oxygen ratio of 6:24. An increase in the oxygen content introduced during CeO2-x film deposition not only stabilizes the conventional bipolar RS but also improves excellent switching uniformity such as large ON/OFF ratio (102), excellent switching device-to-device uniformity and good sweep endurance over 500 repeated RS cycles. Conduction in the low-resistance state (LRS) as well as in the low bias field region in the high-resistance state (HRS) is found to be Ohmic and thus supports the conductive filament (CF) theory. In the high voltage region of HRS, space charge limited conduction (SCLC) and Schottky emission are found to be the dominant conduction mechanisms. A feasible filamentary RS mechanism based on the movement of oxygen ions/vacancies under the bias voltage has been discussed.

Methanol Droplet Combustion in Oxygen-Inert Environments in Microgravity

Science.gov (United States)

Nayagam, Vedha; Dietrich, Daniel L.; Hicks, Michael C.; Williams, Forman A.

2013-01-01

The Flame Extinguishment (FLEX) experiment that is currently underway in the Combustion Integrated Rack facility onboard the International Space Station is aimed at understanding the effects of inert diluents on the flammability of condensed phase fuels. To this end, droplets of various fuels, including alkanes and alcohols, are burned in a quiescent microgravity environment with varying amounts of oxygen and inert diluents to determine the limiting oxygen index (LOI) for these fuels. In this study we report experimental observations of methanol droplets burning in oxygen-nitrogen-carbon dioxide and oxygen-nitrogen-helium gas mixtures at 0.7 and 1 atmospheric pressures. The initial droplet size varied between approximately 1.5 mm and 4 mm to capture both diffusive extinction brought about by insufficient residence time at the flame and radiative extinction caused by excessive heat loss from the flame zone. The ambient oxygen concentration varied from a high value of 30% by volume to as low as 12%, approaching the limiting oxygen index for the fuel. The inert dilution by carbon dioxide and helium varied over a range of 0% to 70% by volume. In these experiments, both freely floated and tethered droplets were ignited using symmetrically opposed hot-wire igniters and the burning histories were recorded onboard using digital cameras, downlinked later to the ground for analysis. The digital images yielded droplet and flame diameters as functions of time and subsequently droplet burning rate, flame standoff ratio, and initial and extinction droplet diameters. Simplified theoretical models correlate the measured burning rate constant and the flame standoff ratio reasonably well. An activation energy asymptotic theory accounting for time-dependent water dissolution or evaporation from the droplet is shown to predict the measured diffusive extinction conditions well. The experiments also show that the limiting oxygen index for methanol in these diluent gases is around 12% to

Tensile properties of V-Cr-Ti alloys after exposure in helium and low-partial-pressure oxygen environments

Energy Technology Data Exchange (ETDEWEB)

Natesan, K.; Soppet, W.K. [Argonne National Lab., IL (United States)

1997-04-01

A test program is in progress to evaluate the effect of oxygen at low pO{sub 2} on the tensile properties of V-(4-5)wt% Cr-(4-5)wt% Ti alloys. Some of the tensile specimens were precharged with oxygen at low pO{sub 2} at 500{degrees}C and reannealed in vacuum at 500{degrees}C in environments with various pO{sub 2} levels and subsequently tensile tested at room temperature. The preliminary results indicate that both approaches are appropriate for evaluating the effect of oxygen uptake on the tensile properties of the alloys. The data showed that in the relatively short-time tests conducted thus far, the maximum engineering stress slightly increased after oxygen exposure but the uniform and total elongation values exhibited significant decrease after exposure in oxygen-containing environments. The data for a specimen exposed to a helium environment were similar to those obtained in low pO{sub 2} environments.

Tensile properties of V-Cr-Ti alloys after exposure in helium and low-partial-pressure oxygen environments

International Nuclear Information System (INIS)

Natesan, K.; Soppet, W.K.

1997-01-01

A test program is in progress to evaluate the effect of oxygen at low pO 2 on the tensile properties of V-(4-5)wt% Cr-(4-5)wt% Ti alloys. Some of the tensile specimens were precharged with oxygen at low pO 2 at 500 degrees C and reannealed in vacuum at 500 degrees C in environments with various pO 2 levels and subsequently tensile tested at room temperature. The preliminary results indicate that both approaches are appropriate for evaluating the effect of oxygen uptake on the tensile properties of the alloys. The data showed that in the relatively short-time tests conducted thus far, the maximum engineering stress slightly increased after oxygen exposure but the uniform and total elongation values exhibited significant decrease after exposure in oxygen-containing environments. The data for a specimen exposed to a helium environment were similar to those obtained in low pO 2 environments

Photoluminescence of colloidal CdSe nano-tetrapods and quantum dots in oxygenic and oxygen-free environments

Energy Technology Data Exchange (ETDEWEB)

Zhao, Lijuan [Donghua University, Applied Physics Department, Shanghai (China); Hong Kong University of Science and Technology, Physics Department and the Institute of Nano-Science and Technology, Hong Kong (China); Pang, Qi; Ge, Weikun; Wang, Jiannong [Hong Kong University of Science and Technology, Physics Department and the Institute of Nano-Science and Technology, Hong Kong (China); Yang, Shihe [Hong Kong University of Science and Technology, Chemistry Department and the Institute of Nano-Science and Technology, Hong Kong (China)

2011-05-15

The effects of oxygenic versus oxygen-free environments on colloidal CdSe nano-tetrapods and quantum dots (QDs) were studied using both continuous and time-resolved photoluminescence (PL) measurements. The decays of PL intensities for tetrapods and QDs in oxygen-free solution (chloroform) and in air (on silicon) can be well fitted by a bi-exponential function. Based on the emission-energy dependence of carrier lifetimes and the amplitude ratio of the fast-decay component to the slow-decay component, the fast and slow PL decays of CdSe nanocrystals are attributed to the recombination of delocalized carriers in the core states and localized carriers in the surface states, respectively. The PL intensities of CdSe nano-tetrapods and QDs were found to be five times and an order of magnitude higher in air than in vacuum, respectively, which is explained by the passivation of surface defects by the polar gas (oxygen) absorption. The lower enhancement in PL intensities of CdSe nano-tetrapods is explained by the special morphology of the tetrapods. (orig.)

Mutations that Allow SIR2 Orthologs to Function in a NAD+-Depleted Environment.

Science.gov (United States)

Ondracek, Caitlin R; Frappier, Vincent; Ringel, Alison E; Wolberger, Cynthia; Guarente, Leonard

2017-03-07

Sirtuin enzymes depend on NAD + to catalyze protein deacetylation. Therefore, the lowering of NAD + during aging leads to decreased sirtuin activity and may speed up aging processes in laboratory animals and humans. In this study, we used a genetic screen to identify two mutations in the catalytic domain of yeast Sir2 that allow the enzyme to function in an NAD + -depleted environment. These mutant enzymes give rise to a significant increase of yeast replicative lifespan and increase deacetylation by the Sir2 ortholog, SIRT1, in mammalian cells. Our data suggest that these mutations increase the stability of the conserved catalytic sirtuin domain, thereby increasing the catalytic efficiency of the mutant enzymes. Our approach to identifying sirtuin mutants that permit function in NAD + -limited environments may inform the design of small molecules that can maintain sirtuin activity in aging organisms. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Pulsed laser deposition of Pb(Zr0.52Ti0.48)O3 thin film on cobalt ferrite nano-seed layered Pt(111)/Si substrate: effect of oxygen pressure

Science.gov (United States)

Khodaei, M.; Seyyed Ebrahimi, S. A.; Park, Yong Jun; Song, Seungwoo; Jang, Hyun Myung; Son, Junwoo; Baik, Sunggi

2014-07-01

The effect of oxygen pressure during pulsed laser deposition of Pb(Zr0.52Ti0.48)O3 (PZT) thin films on CoFe2O4 nano-seed layered Pt(111)/Si substrate was investigated. The PZT film deposited at oxygen pressure lower than 25 mTorr is identified as both perovskite and pyrochlore phases and the films deposited at high oxygen pressure (50-100 mTorr) show the single-phase perovskite PZT that has a perfect (111)-orientation. In addition, the film deposited at PO2 of 50 mTorr has a uniform surface morphology, whereas the film deposited at PO2 of 100 mTorr has a non-uniform surface morphology and more incompacted columnar cross-section microstructure. The polarization of film deposited at 100 mTorr is higher than that deposited at 50 mTorr, but shift of the hysteresis loop along the electrical field axis in the film deposited at PO2 of 100 mTorr is larger than that of the film deposited at PO2 of 50 mTorr.

Deposition of Lanthanum Strontium Cobalt Ferrite (LSCF) Using Suspension Plasma Spraying for Oxygen Transport Membrane Applications

Science.gov (United States)

Fan, E. S. C.; Kesler, O.

2015-08-01

Suspension plasma spray deposition was utilized to fabricate dense lanthanum strontium cobalt ferrite oxygen separation membranes (OSMs) on porous metal substrates for mechanical support. The as-sprayed membranes had negligible and/or reversible material decomposition. At the longer stand-off distance (80 mm), smooth and dense membranes could be manufactured using a plasma with power below approximately 81 kW. Moreover, a membrane of 55 μm was observed to have very low gas leakage rates desirable for OSM applications. This thickness could potentially be decreased further to improve oxygen diffusion by using metal substrates with finer surface pores.

Depositional environments as a guide to uranium mineralization in the Chinle formation, San Rafael Swell, Utah

International Nuclear Information System (INIS)

Lupe, R.

1977-01-01

The sedimentary textures resulting from depositional processes operating in low-energy environments appear to have influenced uranium mineralization. The Chinle consists of three fining-upward, fluvial-lacustrine sequences. Uranium minerals are concentrated in the lower part of the lowest sequence in areas where sediments of low-energy environment are complexly interbedded with sediments of other environments. Areas favorable for uranium exploration exist in the subsurface to the north, west, and south of the Chinle outcrop in the Swell. This determination is based on the spatial distribution of depositional environments and the pattern of Chinle deposition through time. 8 refs

Acid Deposition Phenomena

International Nuclear Information System (INIS)

Ramadan, A.E.K.

2004-01-01

Acid deposition, commonly known as acid rain, occurs when emissions from the combustion of fossil fuels and other industrial processes undergo complex chemical reactions in the atmosphere and fall to the earth as wet deposition (rain, snow, cloud, fog) or dry deposition (dry particles, gas). Rain and snow are already naturally acidic, but are only considered problematic when less than a ph of 5.0 The main chemical precursors leading to acidic conditions are atmospheric concentrations of sulfur dioxide (SO 2 ) and nitrogen oxides (NO x ). When these two compounds react with water, oxygen, and sunlight in the atmosphere, the result is sulfuric (H 2 SO 4 ) and nitric acids (HNO 3 ), the primary agents of acid deposition which mainly produced from the combustion of fossil fuel and from petroleum refinery. Airborne chemicals can travel long distances from their sources and can therefore affect ecosystems over broad regional scales and in locations far from the sources of emissions. According to the concern of petroleum ministry with the environment and occupational health, in this paper we will discussed the acid deposition phenomena through the following: Types of acidic deposition and its components in the atmosphere Natural and man-made sources of compounds causing the acidic deposition. Chemical reactions causing the acidic deposition phenomenon in the atmosphere. Factors affecting level of acidic deposition in the atmosphere. Impact of acid deposition. Procedures for acidic deposition control in petroleum industry

Oxidation of ruthenium thin films using atomic oxygen

Energy Technology Data Exchange (ETDEWEB)

McCoy, A.P.; Bogan, J.; Brady, A.; Hughes, G.

2015-12-31

In this study, the use of atomic oxygen to oxidise ruthenium thin films is assessed. Atomic layer deposited (ALD) ruthenium thin films (~ 3 nm) were exposed to varying amounts of atomic oxygen and the results were compared to the impact of exposures to molecular oxygen. X-ray photoelectron spectroscopy studies reveal substantial oxidation of metallic ruthenium films to RuO{sub 2} at exposures as low as ~ 10{sup 2} L at 575 K when atomic oxygen was used. Higher exposures of molecular oxygen resulted in no metal oxidation highlighting the benefits of using atomic oxygen to form RuO{sub 2}. Additionally, the partial oxidation of these ruthenium films occurred at temperatures as low as 293 K (room temperature) in an atomic oxygen environment. - Highlights: • X-ray photoelectron spectroscopy study of the oxidation of Ru thin films • Oxidation of Ru thin films using atomic oxygen • Comparison between atomic oxygen and molecular oxygen treatments on Ru thin films • Fully oxidised RuO{sub 2} thin films formed with low exposures to atomic oxygen.

Metallogenetic condition and mineralization characteristics of uranium deposit No.114

International Nuclear Information System (INIS)

Niu Lin; Ma Fei; Yang Wanjin

1988-01-01

Deposit No 114 is one of the typical carbonate-type uranium deposits, that are widely distributed in South China. In this paper formational environment of host rock, wall-rock alteration, sulfur, oxygen, carbon isotopes, mineralization temperatures, ore compsitions were studied. Based on the U-Pb isotopic research three mineralization stages in deposit No 114 were established, namely 104 Ma, 61 Ma and 11 Ma. It is suggested, that the deposit No 114 is a polygenetic deposit formed primarily by supergene leaching and hydrothermal reworked. The uranium deposit has multi-sources, the main uranium source of which is from the granite body situated nearby. According to metallogenetic characteristics the authors suggest the favourable geological exploration guides for this kind of ore deposits

Visible photoluminescence from plasma-polymerized-organosilicone thin films deposited from HMDSO/O{sub 2} induced remote plasma: effect of oxygen fraction

Energy Technology Data Exchange (ETDEWEB)

Naddaf, M; Saloum, S [Department of Physics, Atomic Energy Commission of Syria (AECS), PO Box 6091 Damascus (Syrian Arab Republic)], E-mail: scientific6@aec.org.sy

2008-09-07

Visible photoluminescence (PL) from thin films deposited on silicon wafers by remote plasma polymerization of the hexamethyledisiloxane (HMDSO)/O{sub 2} mixture in a radio-frequency hollow cathode discharge reactor has been investigated as a function of different oxygen fractions ({chi}{sub O{sub 2}}=0, 0.38, 0.61, 0.76 and 0.9). At room temperature, the film deposited at ({chi}{sub O{sub 2}}=0 exhibits a strong, broad PL band peak centred at around 537.6 nm. A blue shift and a considerable decrease ({approx}one order) in the intensity of the PL peak are observed after the addition of oxygen. Furthermore, in contrast to the film deposited from pure HMDSO, the low temperature (15 K) PL spectra of the film deposited from different HMDSO/O{sub 2} mixtures exhibit two separated 'green-blue' and 'yellow-green' PL peaks. The PL behaviour of the deposited films is correlated with their structural and morphological properties, investigated by using Fourier transform infrared, atomic force microscope and contact angle techniques. In addition, it is found from spectrophotometry measurements that the deposited films have relatively low absorption coefficients (in the range 100-500 cm{sup -1}) in the spectral range of their PL emission, attractive for possible integrated optics devices.

Oxygen, climate and the chemical evolution of a 1400 million year old tropical marine setting

DEFF Research Database (Denmark)

Wang, Xiaomei; Zhang, Shuichang; Wang, Huajian

2017-01-01

by oxygenated bottom waters. The transition to unit 3 reflects an increase in primary productivity, and the development of a more biologically active OMZ, that supported anoxygenic phototrophic bacteria. Still, in this unit, the bottom waters remained oxygenated. The overlying unit 2 represents the transition...... for the iron. However, the low organic carbon contents, low hydrogen index (HI) values, and the oxidized nature of the reactive iron pool indicate deposition in oxygenated bottom waters. We interpret unit 4 to represent a low-productivity ferruginous oxygen-minimum zone (OMZ) environment, underlain......The Xiamaling Formation is an exceptionally well-preserved sedimentary succession deposited on a marine passive margin about 1400 million years ago. We used a multi-proxy approach, including iron speciation, trace metal dynamics, and organic geochemistry, to explore the evolution of ocean chemistry...

Effects of oxygen partial pressure, deposition temperature, and annealing on the optical response of CdS:O thin films as studied by spectroscopic ellipsometry

Energy Technology Data Exchange (ETDEWEB)

Junda, Maxwell M.; Grice, Corey R.; Subedi, Indra; Yan, Yanfa; Podraza, Nikolas J. [Department of Physics & Astronomy and The Wright Center for Photovoltaics Innovation & Commercialization, University of Toledo, Toledo, Ohio 43606 (United States)

2016-07-07

Ex-situ spectroscopic ellipsometry measurements are made on radio frequency magnetron sputtered oxygenated cadmium sulfide (CdS:O) thin films. Films are deposited onto glass substrates at room temperature and at 270 °C with varying oxygen to total gas flow ratios in the sputtering ambient. Ellipsometric spectra from 0.74 to 5.89 eV are collected before and after annealing at 607 °C to simulate the thermal processes during close-space sublimation of overlying cadmium telluride in that solar cell configuration. Complex dielectric function (ε = ε{sub 1} + iε{sub 2}) spectra are extracted for films as a function of oxygen gas flow ratio, deposition temperature, and post-deposition annealing using a parametric model accounting for critical point transitions and an Urbach tail for sub-band gap absorption. The results suggest an inverse relationship between degree of crystallinity and oxygen gas flow ratio, whereas annealing is shown to increase crystallinity in all samples. Direct band gap energies are determined from the parametric modeling of ε and linear extrapolations of the square of the absorption coefficient. As-deposited samples feature a range of band gap energies whereas annealing is shown to result in gap energies ranging only from 2.40 to 2.45 eV, which is close to typical band gaps for pure cadmium sulfide.

Impurities in chromium deposits produced by electroplating and physical vapor deposition

Energy Technology Data Exchange (ETDEWEB)

Dini, J.W.

1994-05-01

Impurity contents in electrodeposited (hexavalent and trivalent) chromium deposits and physically vapor deposited (thermal evaporation, electron beam evaporation and rf-sputtering) were compared. Oxygen is the key impurity obtained in electrodeposited films but it can be minimized in hexavalent plating solutions by operating at high temperature, e. g., 85 C. Electrodeposits produced in trivalent chromium plating solutions and physically vapor deposited films have much higher oxygen contents than electrodeposits produced in hexavalent chromium solutions operated at temperatures around 85 C. Depending on the target material used for physically vapor deposited films, these films can also have high amounts of other impurities.

The Effects of Ion-Assisted Deposition on the Mechanical, Physical, Chemical and Optical Properties of Magnesium Fluoride Thin Films.

Science.gov (United States)

Kennemore, Charles Milton, III

1992-01-01

This dissertation investigates the results of ion assisted deposition (IAD) on various properties of magnesium fluoride thin films deposited on room temperature substrates. MgF_2 films deposited in this manner have increased abrasion resistance and increased adhesion comparable to that found in films deposited at the usual substrate temperature of approximately 300 ^circC. IAD tends to drive the normal high tensile stress of non-IAD films to a more compressive state thereby reducing the overall stress. The IAD MgF _2 films have a higher index of refraction than non-IAD films, as high as 1.41, and the ultraviolet absorption edge in shifted to longer wavelengths beginning about 350 nm but no detectable absorption at visible wavelengths is seen in the films deposited with less than 250 eV bombardment energies. However, at higher IAD energies beginning at approximately 600 eV an absorption band is present in the red end of the visible spectrum making low energy bombardment the parameter of choice. Transmission electron microscopy and X-ray diffraction studies show that the IAD films have a more amorphous-like structure with fewer and smaller crystallites than non-IAD films deposited on either heated or unheated substrates. Rutherford backscattering spectroscopy (RBS) shows the bombarded films have fluorine depletion that roughly scales with the energy of bombardment with F:Mg ratios as low as 1.69 being found. Bombardment by fluorinated compounds, specifically C_2 F_6 and SF_6 , limit this depletion and in some instances super fluorinate the resulting compound. Additionally, RBS shows that IAD introduces a significant amount of oxygen throughout the film that is unaccountable as water take-up. X-ray photoelectron spectroscopy (XPS) indicates the presence of two compounds of oxygen that are attributed to MgO and Mg(OH)_2 or some oxy-fluoride complex similar to them and it is the introduction of these compounds which provide for the changes in the properties of IAD MgF_2

Electrical properties of GaN-based metal-insulator-semiconductor structures with Al2O3 deposited by atomic layer deposition using water and ozone as the oxygen precursors

Science.gov (United States)

Kubo, Toshiharu; Freedsman, Joseph J.; Iwata, Yasuhiro; Egawa, Takashi

2014-04-01

Al2O3 deposited by atomic layer deposition (ALD) was used as an insulator in metal-insulator-semiconductor (MIS) structures for GaN-based MIS-devices. As the oxygen precursors for the ALD process, water (H2O), ozone (O3), and both H2O and O3 were used. The chemical characteristics of the ALD-Al2O3 surfaces were investigated by x-ray photoelectron spectroscopy. After fabrication of MIS-diodes and MIS-high-electron-mobility transistors (MIS-HEMTs) with the ALD-Al2O3, their electrical properties were evaluated by current-voltage (I-V) and capacitance-voltage (C-V) measurements. The threshold voltage of the C-V curves for MIS-diodes indicated that the fixed charge in the Al2O3 layer is decreased when using both H2O and O3 as the oxygen precursors. Furthermore, MIS-HEMTs with the H2O + O3-based Al2O3 showed good dc I-V characteristics without post-deposition annealing of the ALD-Al2O3, and the drain leakage current in the off-state region was suppressed by seven orders of magnitude.

Oxygen Barrier Coating Deposited by Novel Plasma-enhanced Chemical Vapor Deposition

DEFF Research Database (Denmark)

Jiang, Juan; Benter, M.; Taboryski, Rafael Jozef

2010-01-01

We report the use of a novel plasma-enhanced chemical vapor deposition chamber with coaxial electrode geometry for the SiOx deposition. This novel plasma setup exploits the diffusion of electrons through the inner most electrode to the interior samples space as the major energy source. This confi......We report the use of a novel plasma-enhanced chemical vapor deposition chamber with coaxial electrode geometry for the SiOx deposition. This novel plasma setup exploits the diffusion of electrons through the inner most electrode to the interior samples space as the major energy source...... effect of single-layer coatings deposited under different reaction conditions was studied. The coating thickness and the carbon content in the coatings were found to be the critical parameters for the barrier property. The novel barrier coating was applied on different polymeric materials...

Energy deposition and ion production from thermal oxygen ion precipitation during Cassini's T57 flyby

Science.gov (United States)

Snowden, Darci; Smith, Michael; Jimson, Theodore; Higgins, Alex

2018-05-01

Cassini's Radio Science Investigation (RSS) and Langmuir Probe observed abnormally high electron densities in Titan's ionosphere during Cassini's T57 flyby. We have developed a three-dimensional model to investigate how the precipitation of thermal magnetospheric O+ may have contributed to enhanced ion production in Titan's ionosphere. The three-dimensional model builds on previous work because it calculates both the flux of oxygen through Titan's exobase and the energy deposition and ion production rates in Titan's atmosphere. We find that energy deposition rates and ion production rates due to thermal O+ precipitation have a similar magnitude to the rates from magnetospheric electron precipitation and that the simulated ionization rates are sufficient to explain the abnormally high electron densities observed by RSS and Cassini's Langmuir Probe. Globally, thermal O+ deposits less energy in Titan's atmosphere than solar EUV, suggesting it has a smaller impact on the thermal structure of Titan's neutral atmosphere. However, our results indicate that thermal O+ precipitation can have a significant impact on Titan's ionosphere.

Influence of Oxygen Concentration on the Performance of Ultra-Thin RF Magnetron Sputter Deposited Indium Tin Oxide Films as a Top Electrode for Photovoltaic Devices

Directory of Open Access Journals (Sweden)

Jephias Gwamuri

2016-01-01

Full Text Available The opportunity for substantial efficiency enhancements of thin film hydrogenated amorphous silicon (a-Si:H solar photovoltaic (PV cells using plasmonic absorbers requires ultra-thin transparent conducting oxide top electrodes with low resistivity and high transmittances in the visible range of the electromagnetic spectrum. Fabricating ultra-thin indium tin oxide (ITO films (sub-50 nm using conventional methods has presented a number of challenges; however, a novel method involving chemical shaving of thicker (greater than 80 nm RF sputter deposited high-quality ITO films has been demonstrated. This study investigates the effect of oxygen concentration on the etch rates of RF sputter deposited ITO films to provide a detailed understanding of the interaction of all critical experimental parameters to help create even thinner layers to allow for more finely tune plasmonic resonances. ITO films were deposited on silicon substrates with a 98-nm, thermally grown oxide using RF magnetron sputtering with oxygen concentrations of 0, 0.4 and 1.0 sccm and annealed at 300 °C air ambient. Then the films were etched using a combination of water and hydrochloric and nitric acids for 1, 3, 5 and 8 min at room temperature. In-between each etching process cycle, the films were characterized by X-ray diffraction, atomic force microscopy, Raman Spectroscopy, 4-point probe (electrical conductivity, and variable angle spectroscopic ellipsometry. All the films were polycrystalline in nature and highly oriented along the (222 reflection. Ultra-thin ITO films with record low resistivity values (as low as 5.83 × 10−4 Ω·cm were obtained and high optical transparency is exhibited in the 300–1000 nm wavelength region for all the ITO films. The etch rate, preferred crystal lattice growth plane, d-spacing and lattice distortion were also observed to be highly dependent on the nature of growth environment for RF sputter deposited ITO films. The structural, electrical

Influence of oxygen pressure and aging on LaAlO3 films grown by pulsed laser deposition on SrTiO3 substrates

KAUST Repository

Park, Jihwey; Soh, Yeong-Ah; Aeppli, Gabriel; David, Adrian; Lin, Weinan; Wu, Tao

2014-01-01

The crystal structures of LaAlO3 films grown by pulsed laser deposition on SrTiO3 substrates at oxygen pressure of 10−3 millibars or 10−5 millibars, where kinetics of ablated species hardly depend on oxygen background pressure, are compared. Our

A latitudinal study of oxygen isotopes within horsehair

Science.gov (United States)

Thompson, E.; Bronk Ramsey, C.; McConnell, J. R.

2016-12-01

This study aims to explore the hypothesis that 'if oxygen isotope ratios deplete with decreasing temperature then a study of oxygen isotope ratios within horsehair from Oxfordshire to Iceland will show a latitudinal depletion gradient'. By looking at oxygen isotope values at different geographical positions, we can track the relationship with latitude and with different regional climate features. This will provide a firmer understanding of how to compare climate records from different locations. Additionally, a comparison of the horse breeds from this study to those analysed within previous studies will create an even better understanding of the intra-species variation within the δ18O values of horsehair. A total of 24 horses were sampled on the 7th March from Thordale Stud in Shetland, the Icelandic Food And Veterinary Authority in Iceland, the Exmoor Pony Centre in Exmoor and the Pigeon House Equestrian Centre in Oxfordshire. By starting the sampling process from the most recent growth at the follicle, the sampling date becomes a chronological marker, temporally fixing the first sample within a sequential set of data points extending for one year or longer, depending on the length of each individual hair. The samples were analysed for oxygen isotope values using an IRMS coupled within a Sercon HTEA. Preliminary results show a latitudinal gradient is evident on comparison between the locations, consistent with the findings of Darling and Talbot's study of fresh water isotopes in the British Isles (2003). These results support the hypothesis, showing that a study of oxygen isotope ratios within horse hair from Oxfordshire to Iceland showing a latitudinal depletion gradient, consistent with a depletion of oxygen isotope ratios due to decreasing temperatures. Darling, W. and Talbot, J. (2003). The O and H stable isotope composition of freshwaters in the British Isles. 1. Rainfall. Hydrol. Earth System Science, 7(2), pp.163-181.

Control and enhancement of the oxygen storage capacity of ceria films by variation of the deposition gas atmosphere during pulsed DC magnetron sputtering

Science.gov (United States)

Eltayeb, Asmaa; Vijayaraghavan, Rajani K.; McCoy, Anthony; Venkatanarayanan, Anita; Yaremchenko, Aleksey A.; Surendran, Rajesh; McGlynn, Enda; Daniels, Stephen

2015-04-01

In this study, nanostructured ceria (CeO2) films are deposited on Si(100) and ITO coated glass substrates by pulsed DC magnetron sputtering using a CeO2 target. The influence on the films of using various gas ambients, such as a high purity Ar and a gas mixture of high purity Ar and O2, in the sputtering chamber during deposition are studied. The film compositions are studied using XPS and SIMS. These spectra show a phase transition from cubic CeO2 to hexagonal Ce2O3 due to the sputtering process. This is related to the transformation of Ce4+ to Ce3+ and indicates a chemically reduced state of CeO2 due to the formation of oxygen vacancies. TGA and electrochemical cyclic voltammetry (CV) studies show that films deposited in an Ar atmosphere have a higher oxygen storage capacity (OSC) compared to films deposited in the presence of O2. CV results specifically show a linear variation with scan rate of the anodic peak currents for both films and the double layer capacitance values for films deposited in Ar/O2 mixed and Ar atmosphere are (1.6 ± 0.2) × 10-4 F and (4.3 ± 0.5) × 10-4 F, respectively. Also, TGA data shows that Ar sputtered samples have a tendency to greater oxygen losses upon reduction compared to the films sputtered in an Ar/O2 mixed atmosphere.

Evidence for change in depositional environment in the Arabian Sea

Digital Repository Service at National Institute of Oceanography (India)

Rao, P.S.; Rao, Ch.M.

Sediments of late Pleistocene and Holocene periods, from a 12 m long core collected at a depth of 3627 m from the Arabian Sea, have been studied in order to understand the depositional environment. Sub-samples selected at 5 cm and occasionally at 10...

Uranium mobility in the natural environment - evidence from sedimentary roll-front deposits

International Nuclear Information System (INIS)

Deutsch, W.J.; Serne, R.J.

1983-04-01

Roll-front deposits consist of naturally occurring ore-grade uranium in selected sandstone aquifers throughout the world. The geochemical environment of these roll-front deposits is analogous to the environment of a radioactive waste repository containing redox-sensitive elements during its post-thermal period. The ore deposits are formed by a combination of dissolution, complexation, sorption/precipitation, and mineral formation processes. The uranium, leached from the soil by percolating rainwater, complexes with dissolved carbonate and moves in the oxidizing ground water at very low concentration (parts per billion) levels. The uranium is extracted from the leaching solution by the chemical processes, over long periods of time, at the interfaces between oxidized and reduced sediments. The Eh of the ground water associated with the reduced sediments (Eh = -100 mv to +100 mv) is higher than the Eh expected for most waste repository environments (Eh = -100 mv to -300 mv); this suggests that uranium solids will not be very soluble in the repositories. Data from in-situ leach mining and restoration of roll-front uranium deposits also provide information on the potential mobility of the waste if oxidizing ground water should enter the repository. Uranium solids probably will be initially very soluble in carbonate ground water; however, as reducing conditions are re-estblished through water/rock interactions, the uranium will reprecipitate and the amount of uranium in solution will again equilibrate with the reduced uranium minerals

Deposit Insurance and Risk Shifting in a Strong Regulatory Environment

DEFF Research Database (Denmark)

Bartholdy, Jan; Justesen, Lene Gilje

This study provides empirical evidence on the moral hazard implications of introducing deposit insurance into a strong regulatory environment. Denmark offers a unique setting because commercial banks and savings banks have different ownership structures, but are subject to the same set...... of regulations. The ownership structure in savings banks implies that they have no incentive to increase risk after the implementation of a deposit insurance scheme whereas commercial banks have. Also, at the time of introduction, Denmark had high capital requirements and a strict closure policy. Using...... a difference-in-difference framework we show that commercial banks did not increase their risk compared to savings banks when deposit insurance was introduced. The results also hold for large commercial banks, indicating that the systemic risk did not increase either. Thus for a system with high capital...

Electrochemical corrosion behavior of MSIP Ni coating on depleted uranium surface

International Nuclear Information System (INIS)

Chen Lin; Li Kexue; Wang Qingfu; Wang Xiaohong; Guan Weijun

2014-01-01

The Ni film was prepared by magnetron sputtering ion plating to improve the corrosion resistance of depleted uranium. The corrosion resistance of the Ni film was examined by electrochemical corrosion station. The results show that the Ni film corrosion potential is -100.8 mV, whereas it is -641.2 mV for depleted uranium in 50 μg/g KCl solution. The Ni film is a barrier to protect the depleted uranium substrate avoiding the corrosive media attack. The Ni film polarization resistance and impedance are much higher, while the corrosion current density is much lower contrast with depleted uranium. None crack or flake is found through 70 h corrosion. The corrosion resistance and corrosion current keep stable. It is indicated that the corrosion resistance of depleted uranium is effectively improved after deposited Ni film by magnetron sputtering ion plating. (authors)

Assessing Reservoir Depositional Environments to Develop and Quantify Improvements in CO₂ Storage Efficiency. A Reservoir Simulation Approach

Energy Technology Data Exchange (ETDEWEB)

Okwen, Roland [University of Illinois, Champaign, IL (United States); Frailey, Scott [University of Illinois, Champaign, IL (United States); Leetaru, Hannes [University of Illinois, Champaign, IL (United States); Moulton, Sandy [Illinois State Geological Survey, Champaign, IL (United States)

2014-09-30

The storage potential and fluid movement within formations are dependent on the unique hydraulic characteristics of their respective depositional environments. Storage efficiency (E) quantifies the potential for storage in a geologic depositional environment and is used to assess basinal or regional CO₂ storage resources. Current estimates of storage resources are calculated using common E ranges by lithology and not by depositional environment. The objectives of this project are to quantify E ranges and identify E enhancement strategies for different depositional environments via reservoir simulation studies. The depositional environments considered include deltaic, shelf clastic, shelf carbonate, fluvial deltaic, strandplain, reef, fluvial and alluvial, and turbidite. Strategies considered for enhancing E include CO₂ injection via vertical, horizontal, and deviated wells, selective completions, water production, and multi-well injection. Conceptual geologic and geocellular models of the depositional environments were developed based on data from Illinois Basin oil fields and gas storage sites. The geologic and geocellular models were generalized for use in other US sedimentary basins. An important aspect of this work is the development of conceptual geologic and geocellular models that reflect the uniqueness of each depositional environment. Different injection well completions methods were simulated to investigate methods of enhancing E in the presence of geologic heterogeneity specific to a depositional environment. Modeling scenarios included horizontal wells (length, orientation, and inclination), selective and dynamic completions, water production, and multiwell injection. A Geologic Storage Efficiency Calculator (GSECalc) was developed to calculate E from reservoir simulation output. Estimated E values were normalized to diminish their dependency on fluid relative permeability. Classifying depositional environments according to

Pulsed-laser-deposited, single-crystalline Cu2O films with low resistivity achieved through manipulating the oxygen pressure

Science.gov (United States)

Liu, Xiaohui; Xu, Meng; Zhang, Xijian; Wang, Weiguang; Feng, Xianjin; Song, Aimin

2018-03-01

Low-resistivity, single-crystalline Cu2O films were realized on MgO (110) substrates through manipulating the oxygen pressure (PO2) of pulsed-laser deposition. X-ray diffraction and high resolution transmission electron microscopy measurements revealed that the films deposited at PO2 of 0.06 and 0.09 Pa were single phase Cu2O and the 0.09-Pa-deposited film exhibited the best crystallinity with an epitaxial relationship of Cu2O (110)∥MgO (110) with Cu2O (001)∥MgO (001). The pure phase Cu2O films exhibited higher transmittances and larger band gaps with an optical band gap of 2.56 eV obtained for the 0.09 Pa-deposited film. Hall-effect measurements demonstrated that the Cu2O film deposited at 0.09 Pa had the lowest resistivity of 6.67 Ω cm and highest Hall mobility of 23.75 cm2 v-1 s-1.

Comparison of portable oxygen concentrators in a simulated airplane environment.

Science.gov (United States)

Fischer, Rainald; Wanka, Eva R; Einhaeupl, Franziska; Voll, Klaus; Schiffl, Helmut; Lang, Susanne M; Gruss, Martin; Ferrari, Uta

2013-01-01

Portable oxygen concentrators (POC) are highly desirable for patients with lung disease traveling by airplane, as these devices allow theoretically much higher travel times if additional batteries can be used. However, it is unclear whether POCs produce enough oxygen in airplanes at cruising altitude, even if complying with aviation regulations. We evaluated five frequently used POCs (XPO2 (Invacare, USA), Freestyle (AirSep C., USA), Evergo (Philipps Healthcare, Germany), Inogen One (Inogen, USA), Eclipse 3 (Sequal, USA)) at an altitude of 2650 m (as simulated airplane environment) in 11 patients with chronic obstructive lung disease (COPD) and compared theses POCs with the standard oxygen system (WS120, EMS Ltd., Germany) used by Lufthansa. Oxygen was delivered by each POC for 30 min to each patient at rest, blood gases were then drawn from the arterialized ear lobe. All POCs were able to deliver enough oxygen to increase the PaO(2) of our subjects by at least 1.40 kPa (10 mmHg). However, to achieve this increase, the two most lightweight POCs (Freestyle and Invacare XPO2) had to be run at their maximum level. This causes a significant reduction of battery life. The three other POCs (EverGo, Inogen One, Eclipse 3) and the WS120 were able to increase the PaO(2) by more than 2.55 kPa (20 mmHg), which provides extra safety for patients with more severe basal hypoxemia. When choosing the right oxygen system for air travel in patients in COPD, not only weight, but also battery life and maximum possible oxygen output must be considered carefully. Copyright © 2012 Elsevier Ltd. All rights reserved.

Use of depleted uranium in military conflicts and possible post-conflict chemical and radiological risk to health and the environment

International Nuclear Information System (INIS)

Snihs, Jan Olof; Akerblom, Gustav

2000-01-01

During and after the Balkans conflict in 1999 there were rumours that so-called depleted uranium (DU) had been used in military operations by NATO. Attention was drawn to this issue by a number of countries, and consequently, there is a concern amongst the people of Serbia and Kosovo regarding the possible post-conflict chemical and radiological risk to health and the environment. The UN also has to deal with such concerns from the point of view of security of UN staff in the field. UNEP/Habitat Balkans Task Force (BTF) has been set up to make an overall assessment of the environmental consequences of the conflict and impacts of the conflict on human settlements in Kosovo, Macedonia, Montenegro, Albania and in Serbia. The work was done by organising Technical Missions to provide independent and reliable information which is relevant for the problem under consideration. As regards depleted uranium, a special international expert group, the 'Depleted Uranium Desk Assessment Group' was appointed to analyse and assess the situation. The group was chaired by Snihs. Since little or no information was available on the actual use of depleted uranium in the Kosovo conflict, the expert group was reduced to using available information from the 1990 Gulf conflict and published data on the risks of depleted uranium. It was possible to organise only one visit to Kosovo during the time available for this study, and that visit did not give any indications of contamination from depleted uranium. However, this does not exclude the possibility that there are DU-contaminated areas in Kosovo. By using basic facts relevant for risk assessment and making assumptions about the conditions for exposure to depleted uranium, that are as accurate as possible, it has been possible to assess likely consequences for health and environment. In case of uncertainties in the assumptions, conservative values have been used. On the basis of the conclusions of the assessments there are a number of

Health and environmental problems of using antiarmour munitions containing depleted uranium core

International Nuclear Information System (INIS)

Matousek, J.

2006-01-01

In the 1970s, core of depleted uranium commenced to be introduced into the breakthrough antitank munitions of various calibers and types in order to considerably enhance their effectiveness due to extremely high density in comparison with steel. The health and environmental threats of using this munitions and other weaponry where depleted uranium has been utilised as counterbalance stem from the pyrophoric character of uranium, burnt due to material deformation and friction when penetrating armour targets creating thus highly respirable aerosol of uranium oxides that are deposited in alveoli after being inhaled or in other tissues after being ingested. Composition and main properties of depleted uranium are presented. Chronic effects of deposited particles of uranium oxides are due to internal irradiation of sensitive organs at proceeding radioactive decay accompanied with alpha irradiation. Long-term internal irradiation by radionuclides producing alpha-rays leads to proved risk of increased incidence of carcinoma and leukaemia not to speak on chronic chemical toxicity of uranium, independent of its isotopic composition. Environmental impact of extensive use of munitions with depleted uranium in the recent armed conflicts is assessed. (authors)

Potential research money available from the Acid Deposition Program and Alberta Environment

International Nuclear Information System (INIS)

Primus, C.L.

1992-01-01

It is exceedingly difficult to demonstrate definitive long-term changes in animal health as a result of acid-forming emissions from sour gas wells. A summary is presented of current research in Alberta, followed by the potential for research funding by the Alberta Government/Industry Acid Deposition Program (ADRP). The Alberta Environment research budget consists of four programs in addition to the ADRP: acid deposition effects research in the Athabasca oil sands; western and northern Canada long-range transport of air pollutants; departmental monitoring; and inhalation toxicology and animal health. Animal health research, although a component of the acid deposition issue, is beyond the mandate of Alberta Environment, and the ADRP members committee does not forsee becoming involved in the long-term and complex research required to address the effects of acid-forming emissions on livestock. Funds for additional animal health research must come from other government departments and agencies whose mandate covers this area

High performance solution-deposited amorphous indium gallium zinc oxide thin film transistors by oxygen plasma treatment

KAUST Repository

Nayak, Pradipta K.

2012-05-16

Solution-deposited amorphous indium gallium zinc oxide (a-IGZO) thin film transistors(TFTs) with high performance were fabricated using O2-plasma treatment of the films prior to high temperature annealing. The O2-plasma treatment resulted in a decrease in oxygen vacancy and residual hydrocarbon concentration in the a-IGZO films, as well as an improvement in the dielectric/channel interfacial roughness. As a result, the TFTs with O2-plasma treated a-IGZO channel layers showed three times higher linear field-effect mobility compared to the untreated a-IGZO over a range of processing temperatures. The O2-plasma treatment effectively reduces the required processing temperature of solution-deposited a-IGZO films to achieve the required performance.

[Research advances in identifying nitrate pollution sources of water environment by using nitrogen and oxygen stable isotopes].

Science.gov (United States)

Mao, Wei; Liang, Zhi-wei; Li, Wei; Zhu, Yao; Yanng, Mu-yi; Jia, Chao-jie

2013-04-01

Water body' s nitrate pollution has become a common and severe environmental problem. In order to ensure human health and water environment benign evolution, it is of great importance to effectively identify the nitrate pollution sources of water body. Because of the discrepant composition of nitrogen and oxygen stable isotopes in different sources of nitrate in water body, nitrogen and oxygen stable isotopes can be used to identify the nitrate pollution sources of water environment. This paper introduced the fractionation factors of nitrogen and oxygen stable isotopes in the main processes of nitrogen cycling and the composition of these stable isotopes in main nitrate sources, compared the advantages and disadvantages of five pre-treatment methods for analyzing the nitrogen and oxygen isotopes in nitrate, and summarized the research advances in this aspect into three stages, i. e. , using nitrogen stable isotope alone, using nitrogen and oxygen stable isotopes simultaneously, and combining with mathematical models. The future research directions regarding the nitrate pollution sources identification of water environment were also discussed.

The oxic degradation of sedimentary organic matter 1400 Ma constrains atmospheric oxygen levels

DEFF Research Database (Denmark)

Zhang, Shuichang; Wang, Xiaomei; Wang, Huajian

2017-01-01

shales are enriched in redox-sensitive trace metals, have high concentrations of total organic carbon (TOC), high hydrogen index (HI) and iron speciation indicating deposition under anoxic conditions. In contrast, the green-gray shales show no trace metal enrichments, have low TOC, low HI and iron...... speciation consistent with an oxygenated depositional setting. Altogether, unit 1 displays alternations between oxic and anoxic depositional environments, driving differences in carbon preservation consistent with observations from the modern ocean. We combined our TOC and HI results to calculate...

Lateral transfer of tetrahymanol-synthesizing genes has allowed multiple diverse eukaryote lineages to independently adapt to environments without oxygen

Directory of Open Access Journals (Sweden)

Takishita Kiyotaka

2012-02-01

Full Text Available Abstract Sterols are key components of eukaryotic cellular membranes that are synthesized by multi-enzyme pathways that require molecular oxygen. Because prokaryotes fundamentally lack sterols, it is unclear how the vast diversity of bacterivorous eukaryotes that inhabit hypoxic environments obtain, or synthesize, sterols. Here we show that tetrahymanol, a triterpenoid that does not require molecular oxygen for its biosynthesis, likely functions as a surrogate of sterol in eukaryotes inhabiting oxygen-poor environments. Genes encoding the tetrahymanol synthesizing enzyme squalene-tetrahymanol cyclase were found from several phylogenetically diverged eukaryotes that live in oxygen-poor environments and appear to have been laterally transferred among such eukaryotes. Reviewers This article was reviewed by Eric Bapteste and Eugene Koonin.

Evidence of room temperature ferromagnetism in argon/oxygen annealed TiO2 thin films deposited by electron beam evaporation technique

International Nuclear Information System (INIS)

Mohanty, P.; Kabiraj, D.; Mandal, R.K.; Kulriya, P.K.; Sinha, A.S.K.; Rath, Chandana

2014-01-01

TiO 2 thin films deposited by electron beam evaporation technique annealed in either O 2 or Ar atmosphere showed ferromagnetism at room temperature. The pristine amorphous film demonstrates anatase phase after annealing under Ar/O 2 atmosphere. While the pristine film shows a super-paramagnetic behavior, both O 2 and Ar annealed films display hysteresis at 300 K. X-ray photo emission spectroscopy (XPS), Raman spectroscopy, Rutherford’s backscattering spectroscopy (RBS), cross-sectional transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS) were used to refute the possible role of impurities/contaminants in magnetic properties of the films. The saturation magnetization of the O 2 annealed film is found to be higher than the Ar annealed one. It is revealed from shifting of O 1s and Ti 2p core level spectra as well as from the enhancement of high binding energy component of O 1s spectra that the higher magnetic moment is associated with higher oxygen vacancies. In addition, O 2 annealed film demonstrates better crystallinity, uniform deposition and smoother surface than that of the Ar annealed one from glancing angle X-ray diffraction (GAXRD) and atomic force microscopy (AFM). We conclude that although ferromagnetism is due to oxygen vacancies, the higher magnetization in O 2 annealed film could be due to crystallinity, which has been observed earlier in Co doped TiO 2 film deposited by pulsed laser deposition (Mohanty et al., 2012 [10]). - Highlights: • TiO 2 films were deposited by e-beam evaporation technique and post annealed under O 2 /Ar at 500 °C. • The pristine film shows SPM behavior where as O 2 and Ar annealed films demonstrate RTFM. • The presence of magnetic impurities has been discarded by various characterization techniques. • The magnetic moment is found to be higher in O 2 annealed film than the Ar annealed one. • The higher M s in O 2 annealed film is attributed to oxygen vacancies as well as crystallinity

Large colonial organisms with coordinated growth in oxygenated environments 2.1 Gyr ago

DEFF Research Database (Denmark)

El Albani, Abderrazak; Bengtson, Stefan; Canfield, Donald Eugene

2010-01-01

of colonial organisms. The structures are up to 12 cm in size and have characteristic shapes, with a simple but distinct ground pattern of flexible sheets and, usually, a permeating radial fabric. Geochemical analyses suggest that the sediments were deposited under an oxygenated water column. Carbon...... and sulphur isotopic data indicate that the structures were distinct biogenic objects, fossilized by pyritization early in the formation of the rock. The growth patterns deduced from the fossil morphologies suggest that the organisms showed cell-to-cell signalling and coordinated responses, as is commonly...... associated with multicellular organization(9). The Gabon fossils, occurring after the 2.45-2.32-Gyr increase in atmospheric oxygen concentration(10), may be seen as ancient representatives of multicellular life, which expanded so rapidly 1.5 Gyr later, in the Cambrian explosion....

Surficial origin of North American pitchblende and related uranium deposits

International Nuclear Information System (INIS)

Langford, F.F.

1977-01-01

The ubiquitous association of pitchblende uranium deposits with terrestrial sediments is believed to be the natural result of formation of the orebodies by surficial processes operating under continental conditions. The major uranium deposits of North America illustrate this. The quartz-pebble conglomerate uranium deposits of Elliot Lake, Ontario, have thorium-rich uranium minerals that indicate a detrital origin. With the development of an oxygenic atmosphere before 1,700 m.y. ago, uranium was transported in solution in meteoric surface and near-surface ground water, and produced pitchblende veins in fractures in the basement and in lava flows in terrestrial environments. This accounts for the closee association of fluvial sediments with the pitchblende deposits at Beaverlodge, Rabbit Lake, Baker Lake, and Great Bear Lake, Canada. The development of land plants about 300 m.y. ago produced favorable environments within the terrestrial sandstones themselves, and resulted in the tabular uranium orebodies of the Colorado Plateau. The close relation of tabular orebodies to sedimentation is apparent when compared to recent fluvial sedimentation. In Wyoming, the stratigraphic restriction of the boundary-roll deposits to a few zones in Eocene rocks results from their being remobilized tabular deposits

The dinoflagellate Lingulodinium polyedrum responds to N depletion by a polarized deposition of starch and lipid bodies.

Directory of Open Access Journals (Sweden)

Steve Dagenais Bellefeuille

Full Text Available Dinoflagellates are important contributors to the marine phytoplankton and global carbon fixation, but are also infamous for their ability to form the spectacular harmful algal blooms called red tides. While blooms are often associated with high available nitrogen, there are instances where they are observed in oligotrophic environments. In order to maintain their massive population in conditions of nitrogen limitation, dinoflagellates must have evolved efficient adaptive mechanisms. Here we report the physiological responses to nitrogen deprivation in Lingulodinium polyedrum. We find that this species reacts to nitrogen stress, as do most plants and microalgae, by stopping cell growth and diminishing levels of internal nitrogen, in particular in the form of protein and chlorophyll. Photosynthesis is maintained at high levels for roughly a week following nitrate depletion, resulting in accumulated photosynthetic products in the form of starch. During the second week, photosynthesis rates decrease due to a reduction in the number of chloroplasts and the accumulation of neutral lipid droplets. Surprisingly, the starch granules and lipid droplets are seen to accumulate at opposite poles of the cell. Lastly, we observe that cells acclimated to nitrogen-depleted conditions resume normal growth after addition of inorganic nitrogen, but are able to maintain high cell densities far longer than cells grown continuously in nitrogen-replete conditions.

An Elementary Overview of the Selection of Materials for Service in Oxygen-Enriched Environments

Science.gov (United States)

Davis, Samuel Eddie

2012-01-01

The process for selecting materials for use in oxygen or oxygen-enriched environments is one that continues to be investigated by many industries due to the importance to those industries of oxygen systems. There are several excellent resources available to assist oxygen systems design engineers and end-users, with the most comprehensive being ASTM MNL-36, Safe Use of Oxygen and Oxygen Systems: Handbook for Design, Operation and Maintenance, 2nd Edition. ASTM also makes available several standards for oxygen systems. However, the ASTM publications are extremely detailed, and typically designed for professionals who already possess a working knowledge of oxygen systems. No notable resource exists, whether an ASTM or other organizational publication, which can be used to educate engineers or technicians who have no prior knowledge of the nuances of oxygen system design and safety. This paper will fill the void for information needed by organizations that design or operate oxygen systems. The information in this paper is not new information, but is a concise and easily understood summary of selecting materials for oxygen systems. This paper will serve well as an employee s first introduction to oxygen system materials selection, and probably the employee s first introduction to ASTM.

Crystalline and photoluminescence characteristics of YVO{sub 4}:Sm{sup 3+} thin films grown by pulsed laser deposition under oxygen pressure

Energy Technology Data Exchange (ETDEWEB)

Yang, Hyun Kyoung; Chung, Jong Won; Moon, Byung Kee; Choi, Byung Chun [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Jeong, Jung Hyun [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of)], E-mail: jhjeong@pknu.ac.kr; Yi, Soung Soo [Department of Electronic Material Engineering, Silla University, Busan 617-736 (Korea, Republic of); Kim, Jung Hwan [Department of Physics, Dong Eui University, Busan 614-714 (Korea, Republic of); Kim, Kwang Ho [School of Materials Science and Engineering, Busan National University, Busan 609-735 (Korea, Republic of)

2009-05-15

YVO{sub 4}:Sm{sup 3+} films were deposited on Al{sub 2}O{sub 3} (0 0 0 1) substrates at various oxygen pressures changing from 13.3 to 46.6 Pa by using the pulsed laser deposition method. The crystallinity and surface morphology of these films were investigated by means of X-ray diffraction (XRD) and atomic force microscopy (AFM), respectively. The XRD pattern confirmed that YVO{sub 4}:Sm{sup 3+} film has zircon structure and the AFM study revealed that the films consist of homogeneous grains ranging from 100 to 400 nm. The room temperature photoluminescence (PL) spectra showed that the emitted radiation was dominated by a reddish-orange emission peak at 602 nm radiating from the transition of ({sup 4}G{sub 5/2}{yields}{sup 6}H{sub 7/2}). The crystallinity, surface morphology, and photoluminescence spectra of thin-film phosphors were highly dependent on the deposition conditions, in particular, the substrate temperature. The surface roughness and photoluminescence intensity of these films showed similar behavior as a function of oxygen pressure.

The influence of titanium adhesion layer oxygen stoichiometry on thermal boundary conductance at gold contacts

Science.gov (United States)

Olson, David H.; Freedy, Keren M.; McDonnell, Stephen J.; Hopkins, Patrick E.

2018-04-01

We experimentally demonstrate the role of oxygen stoichiometry on the thermal boundary conductance across Au/TiOx/substrate interfaces. By evaporating two different sets of Au/TiOx/substrate samples under both high vacuum and ultrahigh vacuum conditions, we vary the oxygen composition in the TiOx layer from 0 ≤ x ≤ 2.85. We measure the thermal boundary conductance across the Au/TiOx/substrate interfaces with time-domain thermoreflectance and characterize the interfacial chemistry with x-ray photoemission spectroscopy. Under high vacuum conditions, we speculate that the environment provides a sufficient flux of oxidizing species to the sample surface such that one essentially co-deposits Ti and these oxidizing species. We show that slower deposition rates correspond to a higher oxygen content in the TiOx layer, which results in a lower thermal boundary conductance across the Au/TiOx/substrate interfacial region. Under the ultrahigh vacuum evaporation conditions, pure metallic Ti is deposited on the substrate surface. In the case of quartz substrates, the metallic Ti reacts with the substrate and getters oxygen, leading to a TiOx layer. Our results suggest that Ti layers with relatively low oxygen compositions are best suited to maximize the thermal boundary conductance.

Regime shifts and ecological catastrophes in a model of plankton-oxygen dynamics under the climate change.

Science.gov (United States)

Petrovskii, Sergei; Sekerci, Yadigar; Venturino, Ezio

2017-07-07

It is estimated that more than a half of the total atmospheric oxygen is produced in the oceans due to the photosynthetic activity of phytoplankton. Any significant decrease in the net oxygen production by phytoplankton is therefore likely to result in the depletion of atmospheric oxygen and in a global mass mortality of animals and humans. In its turn, the rate of oxygen production is known to depend on water temperature and hence can be affected by the global warming. We address this problem theoretically by considering a model of a coupled plankton-oxygen dynamics where the rate of oxygen production slowly changes with time to account for the ocean warming. We show that, when the temperature rises sufficiently high, a regime shift happens: the sustainable oxygen production becomes impossible and the system's dynamics leads to fast oxygen depletion and plankton extinction. We also consider a scenario when, after a certain period of increase, the temperature is set on a new higher yet apparently safe value, i.e. before the oxygen depletion disaster happens. We show that in this case the system dynamics may exhibit a long-term quasi-sustainable dynamics that can still result in an ecological disaster (oxygen depletion and mass extinctions) but only after a considerable period of time. Finally, we discuss the early warning signals of the approaching regime shift resulting in the disaster. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Use of OXYGEN-18 in the Development of Methods for Controlled Sputter Deposition of High Critical Transition Temperature Material Thin Films of Predicted Composition and Good Uniformity

Science.gov (United States)

Tidrow, Steven Clay

Two primary concerns, in the sputter deposition of high T_{c} material films, are the prevention of oxygen deficiency in the films and the elimination of the negative ion effect. "Oxygen deficiency" occurs when the amount of oxygen incorporated into the film is less than the amount of oxygen required to form the superconducting material lattice. Oxygen deficiency is due to the volatile nature of oxygen. The negative ion effect occurs when an atom or molecule (typically oxygen) gains an extra electron, is accelerated away from the target and impinges upon a film being grown directly in front of the sputtering target. The impinging particle has enough energy to cause resputtering of the deposited film. The presence of Sr and to a greater extent Ba, may enhance the negative ion effect in these materials. However, it is oxygen which readily forms negative ions that is primarily responsible for the negative ion effect. Thus, oxygen must be given special attention in the sputter deposition of high T_{c} material films. A specially designed sputtering system is used to demonstrate that the negative ion effect can be reduced such that large uniform high T_{c} material films possessing predicted and repeated composition can be grown in an on-axis arrangement. Utilizing this same sputtering system and the volatile nature of oxygen, it is demonstrated that oxygen processes occurring in the chamber during growth of high T_ {c} material films can be investigated using the tracer ^{18}O. In particular, it is shown that ^{18}O can be utilized as a tool for (1) investigating the negative ion effect, (2) investigating oxygen incorporation into high T_{c} material films, (3) investigating oxygen incorporation into the target, (4) tailoring films for oxygen migration and interface investigations and (5) tailoring films for the other specific oxygen investigations. Such sputtering systems that utilize the tracer ^{18}O are necessary for systematic growth of high T_ {c} material films

The Chemistry and Toxicology of Depleted Uranium

Directory of Open Access Journals (Sweden)

Sidney A. Katz

2014-03-01

Full Text Available Natural uranium is comprised of three radioactive isotopes: 238U, 235U, and 234U. Depleted uranium (DU is a byproduct of the processes for the enrichment of the naturally occurring 235U isotope. The world wide stock pile contains some 1½ million tons of depleted uranium. Some of it has been used to dilute weapons grade uranium (~90% 235U down to reactor grade uranium (~5% 235U, and some of it has been used for heavy tank armor and for the fabrication of armor-piercing bullets and missiles. Such weapons were used by the military in the Persian Gulf, the Balkans and elsewhere. The testing of depleted uranium weapons and their use in combat has resulted in environmental contamination and human exposure. Although the chemical and the toxicological behaviors of depleted uranium are essentially the same as those of natural uranium, the respective chemical forms and isotopic compositions in which they usually occur are different. The chemical and radiological toxicity of depleted uranium can injure biological systems. Normal functioning of the kidney, liver, lung, and heart can be adversely affected by depleted uranium intoxication. The focus of this review is on the chemical and toxicological properties of depleted and natural uranium and some of the possible consequences from long term, low dose exposure to depleted uranium in the environment.

Study of the oxygen and substrate bias effects on the defect structure of reactive sputter-deposited SnOx films

International Nuclear Information System (INIS)

Misheva, M.; Nancheva, N.; Docheva, P.; Hadjijska, P.; Djourelov, N.; Elenkov, D.

1999-01-01

The effects of oxygen and substrate bias on the defect structure of reactive sputter-deposited SnOx films were investigated. Samples were analysed using transmission electron microscopy (TEM), transmission electron diffraction (TED), X-ray diffraction (XRD) and positron annihilation spectroscopy (PAS). The oxygen played an important role in the film growth and surface morphology. TEM, TED and XRD showed that increasing of the oxygen partial pressure leads to the formation of films with different crystal phases. The void sizes also depended on oxygen partial pressure. The positron lifetimes and their relative intensities depended on the void concentration, the partial annealing of the vacancies and oxidation of SnO to SnOx. This investigation also showed that the mechanical strength of the films obtained at negative substrate bias is higher and the concentration of vacancy defects is smaller, than in the films, prepared without substrate bias. (author)

Barium depletion in hollow cathode emitters

International Nuclear Information System (INIS)

Polk, James E.; Mikellides, Ioannis G.; Katz, Ira; Capece, Angela M.

2016-01-01

Dispenser hollow cathodes rely on a consumable supply of Ba released by BaO-CaO-Al 2 O 3 source material in the pores of a tungsten matrix to maintain a low work function surface. The examination of cathode emitters from long duration tests shows deposits of tungsten at the downstream end that appear to block the flow of Ba from the interior. In addition, a numerical model of Ba transport in the cathode plasma indicates that the Ba partial pressure in the insert may exceed the equilibrium vapor pressure of the dominant Ba-producing reaction, and it was postulated previously that this would suppress Ba loss in the upstream part of the emitter. New measurements of the Ba depletion depth from a cathode insert operated for 8200 h reveal that Ba loss is confined to a narrow region near the downstream end, confirming this hypothesis. The Ba transport model was modified to predict the depletion depth with time. A comparison of the calculated and measured depletion depths gives excellent qualitative agreement, and quantitative agreement was obtained assuming an insert temperature 70 °C lower than measured beginning-of-life values

Comparative study on the deposition of silicon oxide permeation barrier coatings for polymers using hexamethyldisilazane (HMDSN) and hexamethyldisiloxane (HMDSO)

Science.gov (United States)

Mitschker, F.; Schücke, L.; Hoppe, Ch; Jaritz, M.; Dahlmann, R.; de los Arcos, T.; Hopmann, Ch; Grundmeier, G.; Awakowicz, P.

2018-06-01

The effect of the selection of hexamethyldisiloxane (HMDSO) and hexamethyldisilazane (HMDSN) as a precursor in a microwave driven low pressure plasma on the deposition of silicon oxide barrier coatings and silicon based organic interlayers on polyethylene terephthalate (PET) and polypropylene (PP) substrates is investigated. Mass spectrometry is used to quantify the absolute gas density and the degree of depletion of neutral precursor molecules under variation of oxygen admixture. On average, HMDSN shows a smaller density, a higher depletion and the production of smaller fragments. Subsequently, this is correlated with barrier performance and chemical structure as a function of barrier layer thickness and oxygen admixture on PET. For this purpose, the oxygen transmission rate (OTR) is measured and Fourier transformed infrared (FTIR) spectroscopy as well as x-ray photoelectron spectroscopy (XPS) is performed. HMDSN based coatings exhibit significantly higher barrier performances for high admixtures of oxygen (200 sccm). In comparison to HMDSO based processes, however, a higher supply of oxygen is necessary to achieve a sufficient degree of oxidation, cross-linking and, therefore, barrier performance. FTIR and XPS reveal a distinct carbon content for low oxygen admixtures (10 and 20 sccm) in case of HMDSN based coatings. The variation of interlayer thickness also reveals significantly higher OTR for HMDSO based coatings on PET and PP. Barrier performance of HMDSO based coatings improves with increasing interlayer thickness up to 10 nm for PET and PP. HMDSN based coatings exhibit a minimum of OTR without interlayer on PP and for 2 nm interlayer thickness on PET. Furthermore, HMDSN based coatings show distinctly higher bond strengths to the PP substrate.

Associative Interactions in Crowded Solutions of Biopolymers Counteract Depletion Effects.

Science.gov (United States)

Groen, Joost; Foschepoth, David; te Brinke, Esra; Boersma, Arnold J; Imamura, Hiromi; Rivas, Germán; Heus, Hans A; Huck, Wilhelm T S

2015-10-14

The cytosol of Escherichia coli is an extremely crowded environment, containing high concentrations of biopolymers which occupy 20-30% of the available volume. Such conditions are expected to yield depletion forces, which strongly promote macromolecular complexation. However, crowded macromolecule solutions, like the cytosol, are very prone to nonspecific associative interactions that can potentially counteract depletion. It remains unclear how the cytosol balances these opposing interactions. We used a FRET-based probe to systematically study depletion in vitro in different crowded environments, including a cytosolic mimic, E. coli lysate. We also studied bundle formation of FtsZ protofilaments under identical crowded conditions as a probe for depletion interactions at much larger overlap volumes of the probe molecule. The FRET probe showed a more compact conformation in synthetic crowding agents, suggesting strong depletion interactions. However, depletion was completely negated in cell lysate and other protein crowding agents, where the FRET probe even occupied slightly more volume. In contrast, bundle formation of FtsZ protofilaments proceeded as readily in E. coli lysate and other protein solutions as in synthetic crowding agents. Our experimental results and model suggest that, in crowded biopolymer solutions, associative interactions counterbalance depletion forces for small macromolecules. Furthermore, the net effects of macromolecular crowding will be dependent on both the size of the macromolecule and its associative interactions with the crowded background.

Surface preparation of gold nanostructures on glass by ultraviolet ozone and oxygen plasma for thermal atomic layer deposition of Al{sub 2}O{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Lancaster, Cady A., E-mail: lancaster@chem.utah.edu; Shumaker-Parry, Jennifer S., E-mail: shumaker-parry@chem.utah.edu

2016-08-01

Thin film deposition to create robust plasmonic nanomaterials is a growing area of research. Plasmonic nanomaterials have tunable optical properties and can be used as substrates for surface-enhanced spectroscopies. Due to the surface sensitivity and the dependence of the near-field behavior on structural details, degradation from cleaning or spectroscopic interrogation causes plasmonic nanostructures to lose distinctive localized surface plasmon resonances or exhibit diminished optical near-field enhancements over time. To decrease degradation, conformal thin films of alumina are deposited on nanostructured substrates using atomic layer deposition. While film growth on homogenous surfaces has been studied extensively, atomic layer deposition-based film growth on heterogeneous nanostructured surfaces is not well characterized. In this report, we have evaluated the impact of oxygen plasma and ultraviolet ozone pre-treatments on Au nanoparticle substrates for thin film growth by monitoring changes in plasmonic response and nanostructure morphology. We have found that ultraviolet ozone is more effective than oxygen plasma for cleaning gold nanostructured surfaces, which is in contrast to bulk films of the same material. Our results show that oxygen plasma treatment negatively impacts the nanostructure and alumina coating based on both scanning electron microscopy analysis of morphology and changes in the plasmonic response. - Highlights: • Plasmonic response indicates oxygen plasma damages Au structures and Al{sub 2}O{sub 3} films. • Ultraviolet ozone (UVO) re-activates aged Al{sub 2}O{sub 3}-coated Au nanostructures. • UVO treatments do not damage Au or Al{sub 2}O{sub 3}-coated nanostructures.

Zinc Oxide Nanoparticle Induces Microglial Death by NADPH-Oxidase-Independent Reactive Oxygen Species as well as Energy Depletion.

Science.gov (United States)

Sharma, Anuj Kumar; Singh, Vikas; Gera, Ruchi; Purohit, Mahaveer Prasad; Ghosh, Debabrata

2017-10-01

Zinc oxide nanoparticle (ZnO-NP) is one of the most widely used engineered nanoparticles. Upon exposure, nanoparticle can eventually reach the brain through various routes, interact with different brain cells, and alter their activity. Microglia is the fastest glial cell to respond to any toxic insult. Nanoparticle exposure can activate microglia and induce neuroinflammation. Simultaneous to activation, microglial death can exacerbate the scenario. Therefore, we focused on studying the effect of ZnO-NP on microglia and finding out the pathway involved in the microglial death. The present study showed that the 24 h inhibitory concentration 50 (IC 50 ) of ZnO-NP for microglia is 6.6 μg/ml. Early events following ZnO-NP exposure involved increase in intracellular calcium level as well as reactive oxygen species (ROS). Neither of NADPH oxidase inhibitors, apocynin, (APO) and diphenyleneiodonium chloride (DPIC) were able to reduce the ROS level and rescue microglia from ZnO-NP toxicity. In contrary, N-acetyl cysteine (NAC) showed opposite effect. Exogenous supplementation of superoxide dismutase (SOD) reduced ROS significantly even beyond control level but partially rescued microglial viability. Interestingly, pyruvate supplementation rescued microglia near to control level. Following 10 h of ZnO-NP exposure, intracellular ATP level was measured to be almost 50 % to the control. ZnO-NP-induced ROS as well as ATP depletion both disturbed mitochondrial membrane potential and subsequently triggered the apoptotic pathway. The level of apoptosis-inducing proteins was measured by western blot analysis and found to be upregulated. Taken together, we have deciphered that ZnO-NP induced microglial apoptosis by NADPH oxidase-independent ROS as well as ATP depletion.

To the micro-climatic condition influence upon the environment pollution during exploitation of being oxidized mineral deposits

International Nuclear Information System (INIS)

Akhmedzhanov, T.K.; Al'mukhambetova, Sh.K.; Bajramov, I.M.

1998-01-01

Conducted researches showed dependence of environment pollution rate under exploration of being oxidized mineral deposits from number of meteorological futures of season changes. Zones of gases spreading in atmosphere from sources of pollution in dependence from micro-climatic conditions are estimated. Results can be used during preventive measures projecting for environment in deposits districts. (author)

Aerosol Sampling System for Collection of Capstone Depleted Uranium Particles in a High-Energy Environment

International Nuclear Information System (INIS)

Holmes, Thomas D.; Guilmette, Raymond A.; Cheng, Yung-Sung; Parkhurst, MaryAnn; Hoover, Mark D.

2009-01-01

The Capstone Depleted Uranium Aerosol Study was undertaken to obtain aerosol samples resulting from a kinetic-energy cartridge with a large-caliber depleted uranium (DU) penetrator striking an Abrams or Bradley test vehicle. The sampling strategy was designed to (1) optimize the performance of the samplers and maintain their integrity in the extreme environment created during perforation of an armored vehicle by a DU penetrator, (2) collect aerosols as a function of time post-impact, and (3) obtain size-classified samples for analysis of chemical composition, particle morphology, and solubility in lung fluid. This paper describes the experimental setup and sampling methodologies used to achieve these objectives. Custom-designed arrays of sampling heads were secured to the inside of the target in locations approximating the breathing zones of the vehicle commander, loader, gunner, and driver. Each array was designed to support nine filter cassettes and nine cascade impactors mounted with quick-disconnect fittings. Shielding and sampler placement strategies were used to minimize sampler loss caused by the penetrator impact and the resulting fragments of eroded penetrator and perforated armor. A cyclone train was used to collect larger quantities of DU aerosol for chemical composition and solubility. A moving filter sample was used to obtain semicontinuous samples for depleted uranium concentration determination. Control for the air samplers was provided by five remotely located valve control and pressure monitoring units located inside and around the test vehicle. These units were connected to a computer interface chassis and controlled using a customized LabVIEW engineering computer control program. The aerosol sampling arrays and control systems for the Capstone study provided the needed aerosol samples for physicochemical analysis, and the resultant data were used for risk assessment of exposure to DU aerosol

Investigation of the electrocatalytic activity for oxygen reduction of sputter deposited mixed metal films

International Nuclear Information System (INIS)

Schumacher, L.C.; Holzheuter, I.B.; Nucara, M.C.; Dignam, M.J.

1989-01-01

Sputter-deposited films of silver with lead, manganese and nickel have been studied as possible oxygen reduction electrocatalysts using cyclic voltammetry, rotating disc studies, steady-state polarization and Auger analysis. In general, the Ag-Pb and Ag-Mn films display superior electrocatalytic activity for O 2 reduction, while the Ag-Ni films' performance is inferior to that of pure Ag. For the Ag-Pb films, which show the highest electrocatalytic activity, the mixed metal films display oxidation-reduction behavior which is not simply a superposition of that of the separate metals, and suggests a mechanism for the improved behavior

Depletion of oxygen, nitrate and nitrite in the Peruvian oxygen minimum zone cause an imbalance of benthic nitrogen fluxes

Science.gov (United States)

Sommer, S.; Gier, J.; Treude, T.; Lomnitz, U.; Dengler, M.; Cardich, J.; Dale, A. W.

2016-06-01

Oxygen minimum zones (OMZ) are key regions for fixed nitrogen loss in both the sediments and the water column. During this study, the benthic contribution to N cycling was investigated at ten sites along a depth transect (74-989 m) across the Peruvian OMZ at 12°S. O2 levels were below detection limit down to ~500 m. Benthic fluxes of N2, NO3-, NO2-, NH4+, H2S and O2 were measured using benthic landers. Flux measurements on the shelf were made under extreme geochemical conditions consisting of a lack of O2, NO3- and NO2- in the bottom water and elevated seafloor sulphide release. These particular conditions were associated with a large imbalance in the benthic nitrogen cycle. The sediments on the shelf were densely covered by filamentous sulphur bacteria Thioploca, and were identified as major recycling sites for DIN releasing high amounts of NH4+up to 21.2 mmol m-2 d-1 that were far in excess of NH4+ release by ammonification. This difference was attributed to dissimilatory nitrate (or nitrite) reduction to ammonium (DNRA) that was partly being sustained by NO3- stored within the sulphur oxidizing bacteria. Sediments within the core of the OMZ (ca. 200-400 m) also displayed an excess flux of N of 3.5 mmol m-2 d-1 mainly as N2. Benthic nitrogen and sulphur cycling in the Peruvian OMZ appears to be particularly susceptible to bottom water fluctuations in O2, NO3- and NO2-, and may accelerate the onset of pelagic euxinia when NO3- and NO2- become depleted.

Dependence of nitrite oxidation on nitrite and oxygen in low-oxygen seawater

Science.gov (United States)

Sun, Xin; Ji, Qixing; Jayakumar, Amal; Ward, Bess B.

2017-08-01

Nitrite oxidation is an essential step in transformations of fixed nitrogen. The physiology of nitrite oxidizing bacteria (NOB) implies that the rates of nitrite oxidation should be controlled by concentration of their substrate, nitrite, and the terminal electron acceptor, oxygen. The sensitivities of nitrite oxidation to oxygen and nitrite concentrations were investigated using 15N tracer incubations in the Eastern Tropical North Pacific. Nitrite stimulated nitrite oxidation under low in situ nitrite conditions, following Michaelis-Menten kinetics, indicating that nitrite was the limiting substrate. The nitrite half-saturation constant (Ks = 0.254 ± 0.161 μM) was 1-3 orders of magnitude lower than in cultivated NOB, indicating higher affinity of marine NOB for nitrite. The highest rates of nitrite oxidation were measured in the oxygen depleted zone (ODZ), and were partially inhibited by additions of oxygen. This oxygen sensitivity suggests that ODZ specialist NOB, adapted to low-oxygen conditions, are responsible for apparently anaerobic nitrite oxidation.

Effect of oxygen on the thermomechanical behavior of tantalum thin films during the β-α phase transformation

International Nuclear Information System (INIS)

Knepper, Robert; Stevens, Blake; Baker, Shefford P.

2006-01-01

Tantalum thin films were prepared in the metastable β phase, and their thermomechanical behaviors were investigated in situ in an ultrahigh vacuum environment. Controlled levels of oxygen were incorporated into the films either during deposition, by surface oxidation after deposition, or during thermomechanical testing. The transformation from the β phase to the stable α phase takes place in conjunction with a distinct increase in tensile stress. The thermomechanical behavior is strongly affected by the amount of oxygen to which the film is exposed and the method of exposure. Increasing oxygen content inhibits the phase transformation, requiring higher temperatures to reach completion. It is shown that the phase transformation takes place by a nucleation and growth process that is limited by growth. Changes in the activation energy for the phase transformation due to solute drag are estimated as a function of oxygen content and the mechanisms behind the stress evolution are elucidated

Improvement of Transparent Conducting Performance on Oxygen-Activated Fluorine-Doped Tin Oxide Electrodes Formed by Horizontal Ultrasonic Spray Pyrolysis Deposition.

Science.gov (United States)

Koo, Bon-Ryul; Oh, Dong-Hyeun; Riu, Doh-Hyung; Ahn, Hyo-Jin

2017-12-27

In this study, highly transparent conducting fluorine-doped tin oxide (FTO) electrodes were fabricated using the horizontal ultrasonic spray pyrolysis deposition. In order to improve their transparent conducting performances, we carried out oxygen activation by adjusting the ratio of O 2 /(O 2 +N 2 ) in the carrier gas (0%, 20%, and 50%) used during the deposition process. The oxygen activation on the FTO electrodes accelerated the substitution concentration of F (F O • ) into the oxygen sites in the FTO electrode while the oxygen vacancy (V O • • ) concentration was reduced. In addition, due to growth of pyramid-shaped crystallites with (200) preferred orientations, this oxygen activation caused the formation of a uniform surface structure. As a result, compared to others, the FTO electrode prepared at 50% O 2 showed excellent electrical and optical properties (sheet resistance of ∼4.0 ± 0.14 Ω/□, optical transmittance of ∼85.3%, and figure of merit of ∼5.09 ± 0.19 × 10 -2 Ω -1 ). This led to a superb photoconversion efficiency (∼7.03 ± 0.20%) as a result of the improved short-circuit current density. The photovoltaic performance improvement can be defined by the decreased sheet resistance of FTO used as a transparent conducting electrode in dye-sensitized solar cells (DSSCs), which is due to the combined effect of the high carrier concentration by the improved F O • concentration on the FTO electrodes and the fasted Hall mobility by the formation of a uniform FTO surface structure and distortion relaxation on the FTO lattices resulting from the reduced V O • • • concentration.

Plasma-Oxygen Interaction During Thin Films Deposition by Laser ...

African Journals Online (AJOL)

In this contribution we study the effect of the oxygen pressure on the plasma dynamics during the ablation of oxides materials into an oxygen gas. The study was done using fast imaging and ion probe techniques. Both techniques revealed that a threshold oxygen pressure is needed to initiate the plume oxygen interaction.

Consequences of radioactive deposition on aquatic environments

International Nuclear Information System (INIS)

Suolanen, V.

1994-12-01

The publication concentrates on the analyses of the main effects of radioactive deposition on Nordic aquatic environments. A modelling approach is applied for predicting the temporal behaviour of concentrations in fish of inland freshwater ecosystems. The observed values are considered in parallel with the calculations. The time-integrated consequences, the radiation doses are estimated for the relatively significant dose pathways. After a preliminary study of various lake environments in Nordic countries, three representative examples of lake systems were selected for closer consideration: small forest lake, medium-sized forest lake and mountain lake. The effects of changes in the trophic levels of lakes are also tentatively accounted for. The results of the analyses indicate that the radiological consequences of shallow forest lakes are greater than those of mountain lakes which usually have shorter turnover times compared to forest lakes. In long-term consideration, the fish ingestion pathway may in general become important and, in addition to the external exposure, has a high contribution to the expected doses. (orig.) (8 refs., 11 figs., 9 tabs.)

Ecological risk assessment of depleted uranium in the environment at Aberdeen Proving Ground

International Nuclear Information System (INIS)

Clements, W.H.; Kennedy, P.L.; Myers, O.B.

1993-01-01

A preliminary ecological risk assessment was conducted to evaluate the effects of depleted uranium (DU) in the Aberdeen Proving Ground (APG) ecosystem and its potential for human health effects. An ecological risk assessment of DU should include the processes of hazard identification, dose-response assessment, exposure assessment, and risk characterization. Ecological risk assessments also should explicitly examine risks incurred by nonhuman as well as human populations, because risk assessments based only on human health do not always protect other species. To begin to assess the potential ecological risk of DU release to the environment we modeled DU transport through the principal components of the aquatic ecosystem at APG. We focused on the APG aquatic system because of the close proximity of the Chesapeake Bay and concerns about potential impacts on this ecosystem. Our objective in using a model to estimate environmental fate of DU is to ultimately reduce the uncertainty about predicted ecological risks due to DU from APG. The model functions to summarize information on the structure and functional properties of the APG aquatic system, to provide an exposure assessment by estimating the fate of DU in the environment, and to evaluate the sources of uncertainty about DU transport

Evolution of the Early Triassic marine depositional environment in the Croatian Dinarides

Science.gov (United States)

Aljinović, Dunja; Smirčić, Duje; Horacek, Micha; Richoz, Sylvain; Krystyn, Leopold; Kolar-Jurkovšek, Tea; Jurkovšek, Bogdan

2014-05-01

Dienerian and Smithian are characterized by strong siliciclastic input and deposition of red shales, siltstones and sandstones with intercalation of oolithic and bioclastic grainstones. Hummocky-cross-strata witness the importance of storms. Presence of loadcasts and abundant casts of bivalve shells suggest quick deposition of terrigenous material and instant burying of epifauna during storms. Abundant trace fossils preserved in shales evidence intensive life activity in an overall shallow depositonal environment. During the Spathian deposition of lime mudstones and marls prevails. Two Spathian intervals bear ammonoid fauna suggest deposition in slightly deeper environment and a connection with the open sea testifying a transgression at the beginning of Spathian. Even in deeper environment storms play a significant role assuming deposition above storm wave base. The influence of storms in this deeper environment is recognized as accumulation of coarsegrained bioclastic lag at the base of storm beds, graded calcisiltites, gutter casts and hummocky-cross-stratified beds. Intense bioturbation suggest colonization by organisms between storms. Pending from nature and distribution of facies the Plavno sequence has been interpreted as epeiric ramp. An epeiric ramp is defined here as having a very low bathymetric slope (negligible in its inner regions), no grainy shoreface facies, water depths of tens of meters, a width of many hundreds of kilometers and depositional processes dominated by storms.

Electrical characterization of low temperature deposited oxide films ...

Indian Academy of Sciences (India)

Unknown

electronics on the same substrate (Water and Chu 2002). Plasma enhanced chemical vapour deposition (PECVD) .... sion in depletion region is due to the presence of inter- face traps. The total capacitance in inversion ... The conductance technique is used to deter- mine the interface state density throughout the depletion.

The Effect of Oxygen Partial Pressure during Active Layer Deposition on Bias Stability of a-InGaZnO TFTs

International Nuclear Information System (INIS)

Huang Xiao-Ming; Zhu Hong-Bo; Wang Yong-Jin; Wu Chen-Fei; Lu Hai; Ren Fang-Fang

2015-01-01

The effect of oxygen partial pressure (P_O_2) during the channel layer deposition on bias stability of amorphous indium-gallium-zinc oxide (a-IGZO) thin film transistors (TFTs) is investigated. As P_O_2 increases from 10% to 30%, it is found that the device shows enhanced bias stress stability with significantly reduced threshold voltage drift under positive gate bias stress. Based on the x-ray photoelectron spectroscopy measurement, the concentration of oxygen vacancies (O_V) within the a-IGZO layer is suppressed by increasing P_O_2. Meanwhile, the low-frequency noise analysis indicates that the average trap density near the channel/dielectric interface continuously drops with increasing P_O_2. Therefore, the improved interface quality with increasing P_O_2 during the channel layer deposition can be attributed to the reduction of interface O_V-related defects, which agrees with the enhanced bias stress stability of the a-IGZO TFTs. (paper)

Use of depleted uranium in military conflicts and possible impact on health and environment

International Nuclear Information System (INIS)

Snihs, J.O.; Aakerblom, G.

2000-01-01

There has been concern regarding the possible environmental impacts of depleted uranium (DU) and its possible health effects on both military personnel and on civilians following the Gulf War 1991. These issues have been raised by several non-governmental organizations, some scientists and by a number of press reports. Since DU could also have been used in the Balkan conflict 1999, there has been a concern about the possible consequences of its use for the people and for the environment of this region. Because of this concern it was considered necessary to review existing information on DU and give appropriate recommendations in the aftermath of the Balkans conflict. This was made in October 1999. In November 2000 a Mission to Kosovo was undertaken on basis of new information from NATO

RESOLVE: Regolith and Environment Science and Oxygen and Lunar Volatile Extraction

Science.gov (United States)

Quinn, Jacqueline; Baird, Scott; Colaprete, Anthony; Larson, William; Sanders, Gerald; Picard, Martin

2011-01-01

Regolith & Environment Science and Oxygen & Lunar Volatile Extraction (RESOLVE) is an internationally developed payload that is intended to prospect for resources on other planetary bodies. RESOLVE is a miniature drilling and chemistry plant packaged onto a medium-sized rover to collect and analyze soil for volatile components such as water or hydrogen that could be used in human exploration efforts.

Stability of single dispersed silver nanoparticles in natural and synthetic freshwaters: Effects of dissolved oxygen.

Science.gov (United States)

Zou, Xiaoyan; Li, Penghui; Lou, Jie; Fu, Xiaoyan; Zhang, Hongwu

2017-11-01

Silver nanoparticles (AgNPs) are increasingly used in various commercial products. This increased use raises ecological concerns because of the large release of AgNPs into the environment. Once released, the local water chemistry has the potential to influence the environmental fates and behaviors of AgNPs. The impacts of dissolved oxygen and natural organic matter (NOM) on the dissolution and stability of AgNPs were investigated in synthetic and natural freshwaters for 7 days. In synthetic freshwater, the aggregation of AgNPs occurred due to the compression of the electric double layer, accompanied by the dissolution of AgNPs. However, once oxygen was removed, the highest dissolved Ag (Ag dis ) concentration decreased from 356.5 μg/L to 272.1 μg/L, the pH of the AgNP suspensions increased from less than 7.6 to more than 8.4, and AgNPs were regenerated by the reduction of released Ag + by citrate. The addition of NOM mitigated aggregation, inhibited oxidative dissolution and induced the transformation of AgNPs into Ag 2 S due to the formation of NOM-adsorbed layers, the reduction of Ag + by NOM, and the high affinity of sulfur-enriched species in NOM for Ag. Likewise, in oxygen-depleted natural freshwaters, the inhibition of oxidative dissolution was obtained in comparison with oxygenated freshwaters, showing a decrease in the maximum Ag dis concentration from 137.6 and 57.0 μg/L to 83.3 and 42.4 μg/L from two natural freshwater sites. Our results suggested that aggregation and dissolution of AgNPs in aquatic environments depend on the chemical composition, where oxygen-depleted freshwaters more significantly increase the colloidal stability. In comparison with oxic conditions, anoxic conditions were more favorable to the regeneration of AgNPs by reducing species (e.g., citrate and NOM) and enhanced the stability of nanoparticles. This indicates that some AgNPs will be more stable for long periods in oxygen-deprived freshwaters, and pose more serious

The relationship between mineralisation and depositional environment in Early Proterozoic metasediments of the Pine Creek Geosyncline

International Nuclear Information System (INIS)

Needham, R.S.; Stuart-Smith, P.G.

1984-01-01

Recent geological mapping has indicated changes to the stratigraphy of the Pine Creek Geosyncline. The new stratigraphy and interpreted depositional environments are examined in relation to the distribution and genesis of stratabound mineral deposits. Basinward correlations are made with near-shore carbonate and psammite-rudite units in the Rum Jungle region. Most other units in the same region are condensed, indicating long-lived supratidal, intertidal or shallow conditions during most of the depositional cycle. Units containing most of the mineralisation represent the earliest near-shore developments of strongly reducing partly pelitic and evaporitic conditions and contain mainly uranium and base metals. Areas of potential mineralisation include near-shore environments in the north, and carbonate reefs along growth faults. Two suites of postorogenic felsic volcanics and related sediments deposited in shallow water within and around northwest and east-northeast rift systems, overlie the metasediments of the Pine Creek Geosyncline in the south. The suites have potential for volcanogenic deposits, mostly of uranium, gold and copper

Removal of sulfur compounds from diesel using ArF laser and oxygen.

Science.gov (United States)

Gondal, M A; Siddiqui, M N; Al-Hooshani, K

2013-01-01

A laser-based technique for deep desulfurization of diesel and other hydrocarbon fuels by removal of dimethyldibenzothiophene (DMDBT), a persistent sulfur contaminant in fuel oils has been developed. We report a selective laser excitation of DMDBT in diesel and model compounds such as n-hexane in a reaction chamber under oxygen environment where oxidative reactions can take place. ArF laser emitting at 193 nm was employed for excitation of oxygen and DMDBT, while for process optimization, the laser energy was varied from 50 to 200 mJ/cm(2). The laser-irradiated DMDBT solution under continuous oxygen flow was analyzed by UV absorption spectrometer to determine the photochemical oxidative degradation of DMDBT. In just 5 min of laser irradiation time, almost 95% DMDBT was depleted in a diesel containing 200 ppm of DMDBT. This article provides a new method for the removal of sulfur compounds from diesel by laser based photochemical process.

Post-growth annealing of zinc oxide thin films pulsed laser deposited under enhanced oxygen pressure on quartz and silicon substrates

International Nuclear Information System (INIS)

Rusop, M.; Uma, K.; Soga, T.; Jimbo, T.

2006-01-01

Zinc oxide (ZnO) thin films have been prepared by pulsed laser deposition (PLD) technique at room temperature on quartz and single crystal silicon (1 0 0) substrates. The oxygen ambient gas pressure was attained at 6 Torr during the deposition. The deposited films were post-growth annealed in air at various annealing temperatures for 30 min. The X-ray diffraction (XRD), optical and electrical properties have been measured to study the properties of the films as a function of annealing temperatures. XRD has shown the strength of (0 0 2) peak increases and FWHM value decreases as the annealing temperatures increases from 200 to 600 deg. C. The post-growth annealed at 600 deg. C show dominant c-axis oriented hexagonal wurtize crystal structure and exhibit high average transmittance about 85% in the visible region and very sharp absorption edge at 376 nm with energy band gap of approximately 3.46 eV. Electrical measurement indicates the resistivity decreases with the annealing temperatures up to 600 deg. C, after which it increases with higher annealing temperatures at 800 deg. C. The complex of oxygen vacancy in the ZnO films may be the source of low conductivity in undoped ZnO films

Wire-mesh capped deposition sensors: Novel passive tool for coarse fraction flux estimation of radon thoron progeny in indoor environments

International Nuclear Information System (INIS)

Mayya, Y.S.; Mishra, Rosaline; Prajith, Rama; Sapra, B.K.; Kushwaha, H.S.

2010-01-01

Deposition-based 222 Rn and 220 Rn progeny sensors act as unique, passive tools for determining the long time-averaged progeny deposition fluxes in the environment. The use of these deposition sensors as progeny concentration monitors was demonstrated in typical indoor environments as conceptually superior alternatives to gas-based indirect monitoring methods. In the present work, the dependency of these deposition monitors on various environmental parameters is minimized by capping the deposition sensor with a suitable wire mesh. These wire-mesh capped deposition sensors measure the coarse fraction deposition flux, which is less dependent on the change in environmental parameters like ventilation rate and turbulence. The calibration of these wire-mesh capped coarse fraction progeny sensors was carried out by laboratory controlled experiments. These sensors were deployed both in indoor and in occupational environments having widely different ventilation rates. The obtained coarse fraction deposition velocities were fairly constant in these environments, which further confirmed that the signal on the wire-mesh capped sensors show the least dependency on the change in environmental parameters. This technique has the potential to serve as a passive particle sizer in the general context of nanoparticles using progeny species as surrogates. On the whole, there exists a strong case for developing a passive system that responds only to coarse fraction for providing alternative tools for dosimetry and environmental fine particle research. - Research highlights: → Wire-mesh capped deposition sensor measures the coarse fraction deposition flux → Coarse fraction deposition flux less dependent on environmental conditions → Wire-mesh capped deposition sensor as passive particle sizer

Marine species in ambient low-oxygen regions subject to double jeopardy impacts of climate change.

Science.gov (United States)

Stortini, Christine H; Chabot, Denis; Shackell, Nancy L

2017-06-01

We have learned much about the impacts of warming on the productivity and distribution of marine organisms, but less about the impact of warming combined with other environmental stressors, including oxygen depletion. Also, the combined impact of multiple environmental stressors requires evaluation at the scales most relevant to resource managers. We use the Gulf of St. Lawrence, Canada, characterized by a large permanently hypoxic zone, as a case study. Species distribution models were used to predict the impact of multiple scenarios of warming and oxygen depletion on the local density of three commercially and ecologically important species. Substantial changes are projected within 20-40 years. A eurythermal depleted species already limited to shallow, oxygen-rich refuge habitat (Atlantic cod) may be relatively uninfluenced by oxygen depletion but increase in density within refuge areas with warming. A more stenothermal, deep-dwelling species (Greenland halibut) is projected to lose ~55% of its high-density areas under the combined impacts of warming and oxygen depletion. Another deep-dwelling, more eurythermal species (Northern shrimp) would lose ~4% of its high-density areas due to oxygen depletion alone, but these impacts may be buffered by warming, which may increase density by 8% in less hypoxic areas, but decrease density by ~20% in the warmest parts of the region. Due to local climate variability and extreme events, and that our models cannot project changes in species sensitivity to hypoxia with warming, our results should be considered conservative. We present an approach to effectively evaluate the individual and cumulative impacts of multiple environmental stressors on a species-by-species basis at the scales most relevant to managers. Our study may provide a basis for work in other low-oxygen regions and should contribute to a growing literature base in climate science, which will continue to be of support for resource managers as climate change

The Abiotic Depletion Potential: Background, Updates, and Future

Directory of Open Access Journals (Sweden)

Lauran van Oers

2016-03-01

Full Text Available Depletion of abiotic resources is a much disputed impact category in life cycle assessment (LCA. The reason is that the problem can be defined in different ways. Furthermore, within a specified problem definition, many choices can still be made regarding which parameters to include in the characterization model and which data to use. This article gives an overview of the problem definition and the choices that have been made when defining the abiotic depletion potentials (ADPs for a characterization model for abiotic resource depletion in LCA. Updates of the ADPs since 2002 are also briefly discussed. Finally, some possible new developments of the impact category of abiotic resource depletion are suggested, such as redefining the depletion problem as a dilution problem. This means taking the reserves in the environment and the economy into account in the reserve parameter and using leakage from the economy, instead of extraction rate, as a dilution parameter.

Quantification of Gaseous Elemental Mercury Dry Deposition to Environmental Surfaces using Mercury Stable Isotopes in a Controlled Environment

Science.gov (United States)

Rutter, A. P.; Schauer, J. J.; Shafer, M. M.; Olson, M.; Robinson, M.; Vanderveer, P.; Creswell, J. E.; Parman, A.; Mallek, J.; Gorski, P.

2009-12-01

Andrew P. Rutter (1) * *, James J, Schauer (1,2) *, Martin M. Shafer(1,2), Michael R. Olson (1), Michael Robinson (1), Peter Vanderveer (3), Joel Creswell (1), Justin L. Mallek (1), Andrew M. Parman (1) (1) Environmental Chemistry and Technology Program, 660 N. Park St, Madison, WI 53705. (2) Wisconsin State Laboratory of Hygiene, 2601 Agriculture Drive, Madison, WI 53718. (3) Biotron, University of Wisconsin - Madison, 2115 Observatory Drive, Madison, WI 53706 * Correspond author(jjschauer@wisc.edu) * *Presenting author (aprutter@wisc.edu) Abstract Gaseous elemental mercury (GEM) is the predominant component of atmospheric mercury outside of arctic depletion events, and locations where anthropogenic point sources are not influencing atmospheric concentrations. GEM constitutes greater than 99% of the mercury mass in most rural and remote locations. While dry and wet deposition of atmospheric mercury is thought to be dominated by oxidized mercury (a.k.a. reactive mercury), only small GEM uptake to environmental surfaces could impact the input of mercury to terrestrial and aquatic ecosystems. Dry deposition and subsequent re-emission of gaseous elemental mercury is a pathway from the atmosphere that remains only partially understood from a mechanistic perspective. In order to properly model GEM dry deposition and re-emission an understanding of its dependence on irradiance, temperature, and relative humidity must be measured and parameterized for a broad spectrum of environmental surfaces colocated with surrogate deposition surfaces used to make field based dry deposition measurements. Measurements of isotopically enriched GEM dry deposition were made with a variety of environmental surfaces in a controlled environment room at the University of Wisconsin Biotron. The experimental set up allowed dry deposition components which are not easily separated in the field to be decoupled. We were able to isolate surface transfer processes from variabilities caused by

Reduced oxygen enhancement ratio at low doses

International Nuclear Information System (INIS)

Palcic, B.; Skarsgard, L.D.

1984-01-01

The oxygen depletion rate in cell suspensions was measured using a Clark electrode. It was found that under experimental conditions used in this laboratory for hypoxic irradiations, the oxygen levels before the start of irradiation are always below 0.1μm, the levels which could give any significant enhancement to radiation inactivation by x-rays. The measured O/sub 2/ depletion rates were comparable to those reported in the literature. Chinese hamster cells (CHO) were made hypoxic by gas exchange, combined with metabolic consumption of oxygen by cells at 37 0 C. Full survival curves were determined in the dose range 0 to 3Gy using the low dose survival assay. The results confirmed the authors' earlier finding that the OER decreases at low doses. The authors therefore believe that the dose-dependent OER is a true radiobiological phenomenon and not an artifact of the experimental method used in the low dose survival assay

Molecular diversity of fungi from marine oxygen-deficient environments (ODEs)

Digital Repository Service at National Institute of Oceanography (India)

Manohar, C.S.; Forster, D.; Kauff, F.; Stoeck, T.

. Sparrow Jr F K (1936) Biological observations of the marine fungi of woods hole waters. Biol Bull 70: 236-263. States JS & Christensen M (2001) Fungi Associated with Biological Soil Crusts in Desert Grasslands of Utah and Wyoming. Mycologia 93: 432... version: Biology of marine fungi. Ed. by: Raghukumar, C. (Prog. Mol. Subcellular Biol). Springer, vol.53 (Chap 10); 2012; 189-208 Chapter # 10 Molecular diversity of fungi from marine oxygen-deficient environments (ODEs) Cathrine S. Jebaraj 1...

Deposit model for heavy-mineral sands in coastal environments: Chapter L in Mineral deposit models for resource assessment

Science.gov (United States)

Van Gosen, Bradley S.; Fey, David L.; Shah, Anjana K.; Verplanck, Philip L.; Hoefen, Todd M.

2014-01-01

This report provides a descriptive model of heavy-mineral sands, which are sedimentary deposits of dense minerals that accumulate with sand, silt, and clay in coastal environments, locally forming economic concentrations of the heavy minerals. This deposit type is the main source of titanium feedstock for the titanium dioxide (TiO2) pigments industry, through recovery of the minerals ilmenite (Fe2+TiO3), rutile (TiO2), and leucoxene (an alteration product of ilmenite). Heavy-mineral sands are also the principal source of zircon (ZrSiO4) and its zirconium oxide; zircon is often recovered as a coproduct. Other heavy minerals produced as coproducts from some deposits are sillimanite/kyanite, staurolite, monazite, and garnet. Monazite [(Ce,La,Nd,Th)PO4] is a source of rare earth elements as well as thorium, which is used in thorium-based nuclear power under development in India and elsewhere.

Oxygen effect on the electrical characteristics of pentacene transistors

International Nuclear Information System (INIS)

Hu Yan; Dong Guifang; Hu Yuanchuan; Wang Liduo; Qiu Yong

2006-01-01

The effect of oxygen on the electrical characteristics of organic thin film transistors with pentacene as the active layer has been investigated. The saturation currents and mobilities of the transistors increase as the ambient oxygen concentration decreases, which is ascribed to the formation of a charge transfer complex between pentacene and O 2 . The deposition rate of the pentacene layer affects this phenomenon. The transistor with the pentacene layer deposited at a rate of 15 nm min -1 shows higher sensitivity to oxygen concentration than the device with the pentacene layer deposited at 30 nm min -1 . We suggest that when deposited at a lower rate the pentacene film is less compact, leading to easier entrance of oxygen into the charge accumulation region

In EXOG-depleted cardiomyocytes cell death is marked by a decreased mitochondrial reserve capacity of the electron transport chain

NARCIS (Netherlands)

Tigchelaar, Wardit; De Jong, Anne Margreet; van Gilst, Wiek H.; De Boer, Rudolf A.; Sillje, Herman H. W.

Depletion ofmitochondrial endo/exonuclease G-like (EXOG) in cultured neonatal cardiomyocytes stimulates mitochondrial oxygen consumption rate (OCR) and induces hypertrophy via reactive oxygen species (ROS). Here, we show that neurohormonal stress triggers cell death in endo/exonuclease

Experimental Acidification Causes Soil Base-Cation Depletion at the Bear Brook Watershed in Maine

Science.gov (United States)

Ivan J. Fernandez; Lindsey E. Rustad; Stephen A. Norton; Jeffrey S. Kahl; Bernard J. Cosby

2003-01-01

There is concern that changes in atmospheric deposition, climate, or land use have altered the biogeochemistry of forests causing soil base-cation depletion, particularly Ca. The Bear Brook Watershed in Maine (BBWM) is a paired watershed experiment with one watershed subjected to elevated N and S deposition through bimonthly additions of (NH4)2SO4. Quantitative soil...

CO Depletion: A Microscopic Perspective

Energy Technology Data Exchange (ETDEWEB)

Cazaux, S. [Faculty of Aerospace Engineering, Delft University of Technology, Delft (Netherlands); Martín-Doménech, R.; Caro, G. M. Muñoz; Díaz, C. González [Centro de Astrobiología (INTA-CSIC), Ctra. de Ajalvir, km 4, Torrejón de Ardoz, E-28850 Madrid (Spain); Chen, Y. J. [Department of Physics, National Central University, Jhongli City, 32054, Taoyuan County, Taiwan (China)

2017-11-10

In regions where stars form, variations in density and temperature can cause gas to freeze out onto dust grains forming ice mantles, which influences the chemical composition of a cloud. The aim of this paper is to understand in detail the depletion (and desorption) of CO on (from) interstellar dust grains. Experimental simulations were performed under two different (astrophysically relevant) conditions. In parallel, Kinetic Monte Carlo simulations were used to mimic the experimental conditions. In our experiments, CO molecules accrete onto water ice at temperatures below 27 K, with a deposition rate that does not depend on the substrate temperature. During the warm-up phase, the desorption processes do exhibit subtle differences, indicating the presence of weakly bound CO molecules, therefore highlighting a low diffusion efficiency. IR measurements following the ice thickness during the TPD confirm that diffusion occurs at temperatures close to the desorption. Applied to astrophysical conditions, in a pre-stellar core, the binding energies of CO molecules, ranging between 300 and 850 K, depend on the conditions at which CO has been deposited. Because of this wide range of binding energies, the depletion of CO as a function of A{sub V} is much less important than initially thought. The weakly bound molecules, easily released into the gas phase through evaporation, change the balance between accretion and desorption, which result in a larger abundance of CO at high extinctions. In addition, weakly bound CO molecules are also more mobile, and this could increase the reactivity within interstellar ices.

The Effect of Sintering Oxygen Partial Pressure on a SmBiO3 Buffer Layer for Coated Conductors via Chemical Solution Deposition

Directory of Open Access Journals (Sweden)

Xiaolei Zhu

2016-10-01

Full Text Available The application of high-temperature YBa2Cu3O7−δ (YBCO superconducting material is a considerable prospect for the growing energy shortages. Here, SmBiO3 (SBO films were deposited on (100-orientated yttrium-stabilized zirconia (YSZ simple crystal substrates via the chemical solution deposition (CSD approach for coated conductors, and the effects of sintering oxygen partial pressure on SBO films were studied. The crystalline structures and surface morphologies of SBO films were characterized by X-ray diffraction (XRD, scanning electron microscopy (SEM, and atomic force microscope (AFM. The optimized growth temperature, the intensity ratios of the SBO (200 peak to the SBO (111 peak, and the crystallinities of SBO films increased with the sintering oxygen partial pressure. The SEM and AFM images displayed a smooth and well-distributed surface in the argon atmosphere. The subsequent YBCO films with superconducting transition temperatures (Tc = 89.5 K, 90.2 K, and 86.2 K and critical current densities (Jc = 0.88 MA/cm2, 1.69 MA/cm2, and 0.09 MA/cm2; 77 K, self-field were deposited to further check the qualities of the SBO layer. These results indicated that sintering oxygen partial pressure had an effect on the epitaxial growth of the SBO buffer layer and YBCO superconducting properties. The experimental results may be a usable reference for the epitaxial growth of YBCO-coated conductors and other oxides.

Polymer growth rate in a wire chamber with oxygen, water, or alcohol gas additives

International Nuclear Information System (INIS)

Boyarski, Adam M.

2009-01-01

The rate of polymer growth on wires was measured in a wire chamber while the chamber was aged initially with helium:isobutane (80:20) gas, and then with either oxygen, water, or alcohol added to the gas. At the completion of the aging process for each gas mixture, the carbon content on the wires was measured in a scanning electron microscope/energy dispersive X-ray (SEM/EDX) instrument. The same physical wires were used in all the gas mixtures, allowing measurement of polymer build-up or polymer depletion by each gas additive. It is found that the rate of polymer growth is not changed by the presence of oxygen, water, or alcohol. Conjecture that oxygen reduces breakdown by removing polymer deposits on field wires is negated by these measurements. Instead, it appears that the reduced breakdown is due to lower resistance in the polymer from oxygen ions being transported into the polymer. It is also observed that field wires bombarded by the electrons in the SEM and then placed back into the chamber show an abundance of single electrons being emitted, indicating that electron charge is trapped in the polymer layer and that a high electric field is necessary to remove the charge.

Mechanical and Electrochemical Performance of Carbon Fiber Reinforced Polymer in Oxygen Evolution Environment

Directory of Open Access Journals (Sweden)

Ji-Hua Zhu

2016-11-01

Full Text Available Carbon fiber-reinforced polymer (CFRP is recognized as a promising anode material to prevent steel corrosion in reinforced concrete. However, the electrochemical performance of CFRP itself is unclear. This paper focuses on the understanding of electrochemical and mechanical properties of CFRP in an oxygen evolution environment by conducting accelerated polarization tests. Different amounts of current density were applied in polarization tests with various test durations, and feeding voltage and potential were measured. Afterwards, tensile tests were carried out to investigate the failure modes for the post-polarization CFRP specimens. Results show that CFRP specimens had two typical tensile-failure modes and had a stable anodic performance in an oxygen evolution environment. As such, CFRP can be potentially used as an anode material for impressed current cathodic protection (ICCP of reinforced concrete structures, besides the fact that CFRP can strengthen the structural properties of reinforced concrete.

Carbonate petrography, kerogen distribution, and carbon and oxygen isotope variations in an early Proterozoic transition from limestone to iron-formation deposition, Transvaal Supergroup, South Africa

Science.gov (United States)

Beukes, N. J.; Klein, C.; Kaufman, A. J.; Hayes, J. M.

1990-01-01

The transition zone comprises Campbellrand microbialaminated (replacing "cryptalgalaminate") limestone and shale, with minor dolomite, conformably overlain by the Kuruman Iron Formation of which the basal part is characterized by siderite-rich microbanded iron-formation with minor magnetite and some hematite-containing units. The iron-formation contains subordinate intraclastic and microbialaminated siderite mesobands and was deposited in deeper water than the limestones. The sequence is virtually unaltered with diagenetic mineral assemblages reflecting a temperature interval of about 110 degrees to 170 degrees C and pressures of 2 kbars. Carbonate minerals in the different rock types are represented by primary micritic precipitates (now recrystallized to microsparite), early precompactional sparry cements and concretions, deep burial limpid euhedral sparites, and spar cements precipitated from metamorphic fluids in close contact with diabase sills. Paragenetic pathways of the carbonate minerals are broadly similar in all lithofacies with kerogen intimately associated with them. Kerogen occurs as pigmentation in carbonate crystals, as reworked organic detritus in clastic-textured carbonate units, and as segregations of kerogen pigment around late diagenetic carbonate crystals. Locally kerogen may also be replaced by carbonate spar. Carbon isotope compositions of the carbonate minerals and kerogen are dependent on their mode of occurrence and on the composition of the dominant carbonate species in a specific lithofacies. Integration of sedimentary, petrographic, geochemical, and isotopic results makes it possible to distinguish between depositional, early diagenetic, deep burial, and metamorphic effects on the isotopic compositions of the carbonate minerals and the kerogen in the sequence. Major conclusions are that deep burial thermal decarboxylation led to 13C depletion in euhedral ferroan sparites and 13C enrichment in kerogen (organic carbon). Metamorphic

Reverse depletion effects and the determination of ligand density on some spherical bioparticles

Energy Technology Data Exchange (ETDEWEB)

Wang, Chunxiang [Heilongjiang Bayi Agricultural University (China); Liu, Yanhui, E-mail: ionazati@itp.ac.cn; Fan, Yangtao; Liu, Yijun; Li, Qiancheng; Xu, Houqiang, E-mail: houqiangxu@yahoo.com [Guizhou University (China)

2016-06-15

In cell environments crowded with macromolecules, the depletion effects act and assist in the assembly of a wide range of cellular structures, from the cytoskeleton to the chromatin loop, which are well accepted. But a recent quantum dot experiment indicated that the dimensions of the receptor–ligand complex have strong effects on the size-dependent exclusion of proteins in cell environments. In this article, a continuum elastic model is constructed to resolve the competition between the dimension of the receptor–ligand complex and depletion effects in the endocytosis of a spherical virus-like bioparticle. Our results show that the depletion effects do not always assist endocytosis of a spherical virus-like bioparticle; while the dimension of the ligand–receptor complex is larger than the size of a small bioparticle in cell environments, the depletion effects do not work and reverse effects appear. The ligand density covered on the virus can be identified quantitatively.

Evaluating the Contributions of Atmospheric Deposition of Carbon and Other Nutrients to Nitrification in Alpine Environments

Science.gov (United States)

Oldani, K. M.; Mladenov, N.; Williams, M. W.

2013-12-01

The Colorado Front Range of the Rocky Mountains contains undeveloped, barren soils, yet in this environment there is strong evidence for a microbial role in increased nitrogen (N) export. Barren soils in alpine environments are severely carbon-limited, which is the main energy source for microbial activity and sustenance of life. It has been shown that atmospheric deposition can contain high amounts of organic carbon (C). Atmospheric pollutants, dust events, and biological aerosols, such as bacteria, may be important contributors to the atmospheric organic C load. In this stage of the research we evaluated seasonal trends in the chemical composition and optical spectroscopic (fluorescence and UV-vis absorbance) signatures of snow, wet deposition, and dry deposition in an alpine environment at Niwot Ridge in the Rocky Mountains of Colorado to obtain a better understanding of the sources and chemical character of atmospheric deposition. Our results reveal a positive trend between dissolved organic carbon concentrations and calcium, nitrate and sulfate concentrations in wet and dry deposition, which may be derived from such sources as dust and urban air pollution. We also observed the presence of seasonally-variable fluorescent components that may be attributed to fluorescent pigments in bacteria. These results are relevant because atmospheric inputs of carbon and other nutrients may influence nitrification in barren, alpine soils and, ultimately, the export of nitrate to alpine watersheds.

Widespread functional anoxia in the oxygen minimum zone of the Eastern South Pacific

Science.gov (United States)

Thamdrup, Bo; Dalsgaard, Tage; Revsbech, Niels Peter

Oxygen minimum zones (OMZs) as found in the Eastern Pacific and Indian Ocean are biogeochemical hot spots with a disproportionately large role in the marine nitrogen cycle, and they are important components of the highly productive ecosystems in which they occur. Although the oxygen-depleted waters have been known for a century, oxygen levels inside them are not well constrained and the regulation of their anaerobic processes by oxygen is poorly understood. We deployed highly sensitive STOX oxygen sensors with a detection limit of 10 nmol kg-1 in combination with conventional hydrographic oxygen sensors along a cruise track transecting the Eastern South Pacific OMZ from South to North along the coast of Chile and Peru. Oxygen was below the detection limit throughout the ˜200 m thick OMZ core in most casts with STOX sensors. The only exception was an offshore location off Peru where oxygen was 10-50 nmol kg-1 in the core, likely as the result of a transient intrusion. Oxygen was also not detected in the OMZ core in further casts with conventional sensors, which had a detection limit of 90 nmol kg-1 after STOX-based zero calibration. Our measurements tighten the constraints on typical oxygen concentrations in the inner part of the OMZ by at least an order of magnitude relative to previous reports. Nitrite only accumulated when oxygen was depleted below 50 nmol kg-1, which indicates that nitrogen cycling is much more sensitive to oxygen than previously estimated. We argue that extreme oxygen depletion to low nanomalar or even picomolar concentrations is a normal condition in the South Pacific OMZ, and suggest that the OMZ core is in fact functionally anoxic over wide regions for extended periods. Our results further indicate that oxygen dynamics in the low nanomolar range play an important role in OMZ biogeochemistry.

Apparatus for simultaneously measuring electrical conductivity and oxygen fugacity

Energy Technology Data Exchange (ETDEWEB)

Netherton, R.; Duba, A.

1978-01-31

Electrical conductivity studies of silicates are useful in determining temperature vs depth in the earth. Realistic laboratory measurements of conduction mechanisms require that exact determinations of oxygen fugacity (fo{sub 2}) be made in the experimental environment. An apparatus is described that monitors system fo{sub 2} with a calcia-doped zirconia-oxygen cell while measuring electrical conductivity of iron-bearing silicates at high temperature (greater than 1000 K). The fo{sub 2} calculated thermodynamically from CO/CO{sub 2} mixing ratios agreed well with measurements made with the zirconia cell at 1473 K, except for fo{sub 2} greater than 10{sup -4} Pa, where, on a log{sub 10} scale, mixing-ratio errors were as large as +- 0.2. These errors are attributed to oxygen contamination in the CO{sub 2} and to mobile carbon deposits that formed in the apparatus.

Lagrangian-similarity diffusion-deposition model

International Nuclear Information System (INIS)

Horst, T.W.

1979-01-01

A Lagrangian-similarity diffusion model has been incorporated into the surface-depletion deposition model. This model predicts vertical concentration profiles far downwind of the source that agree with those of a one-dimensional gradient-transfer model

Interaction of nitroimidazole sensitizers and oxygen in the radiosensitization of mammalian cells at ultrahigh dose rates

International Nuclear Information System (INIS)

Michaels, H.B.; Ling, C.C.; Epp, E.R.; Peterson, E.C.

1981-01-01

When CHO cells, equilibrated with 0.44% oxygen, are irradiated with single 3-nsec pulses of electrons from a 600-kV-field emission source, a breaking survival curve is observed. The breaking behavior, believed to be the result of radiolytic oxygen depletion, can be prevented by the presence of a relatively low concentration of the hypoxic cell sensitizer misonidazole; similar results are obtained with metronidazole and Ro-05-9963. The resulting survival curves exhibit a sensitized response similar to that obtained with conventional dose rate radiation for CHO cells under this oxygen concentration. This degree of sensitization is greater than that observed for CHO cells irradiated at ultrahigh dose rates under the same concentration of sensitizer in nitrogen. The data suggest that the nitroimidazole compounds interfere with the radiation chemical oxygen depletion process and that the radiosensitization observed in the nonbreaking survival curve is the consequence of sensitization by both the nitroimidazole and, primarily, the oxygen rather than a direct subsitution for oxygen by the sensitizer. This conclusion is also supported by data obtained in double-pulse experiments. The results are discussed with regard to the mechanisms of the oxygen depletion process and radiosensitization

Blood oxygen depletion is independent of dive function in a deep diving vertebrate, the northern elephant seal.

Directory of Open Access Journals (Sweden)

Jessica U Meir

Full Text Available Although energetics is fundamental to animal ecology, traditional methods of determining metabolic rate are neither direct nor instantaneous. Recently, continuous blood oxygen (O2 measurements were used to assess energy expenditure in diving elephant seals (Mirounga angustirostris, demonstrating that an exceptional hypoxemic tolerance and exquisite management of blood O2 stores underlie the extraordinary diving capability of this consummate diver. As the detailed relationship of energy expenditure and dive behavior remains unknown, we integrated behavior, ecology, and physiology to characterize the costs of different types of dives of elephant seals. Elephant seal dive profiles were analyzed and O2 utilization was classified according to dive type (overall function of dive: transit, foraging, food processing/rest. This is the first account linking behavior at this level with in vivo blood O2 measurements in an animal freely diving at sea, allowing us to assess patterns of O2 utilization and energy expenditure between various behaviors and activities in an animal in the wild. In routine dives of elephant seals, the blood O2 store was significantly depleted to a similar range irrespective of dive function, suggesting that all dive types have equal costs in terms of blood O2 depletion. Here, we present the first physiological evidence that all dive types have similarly high blood O2 demands, supporting an energy balance strategy achieved by devoting one major task to a given dive, thereby separating dive functions into distinct dive types. This strategy may optimize O2 store utilization and recovery, consequently maximizing time underwater and allowing these animals to take full advantage of their underwater resources. This approach may be important to optimizing energy expenditure throughout a dive bout or at-sea foraging trip and is well suited to the lifestyle of an elephant seal, which spends > 90% of its time at sea submerged making diving its

The effect of oxygen pressure on structure, electrical conductivity and oxygen permeability of Ba0.5Sr0.5Co0.8Fe0.2O3-δ thin films by pulsed laser deposition

Directory of Open Access Journals (Sweden)

S Daneshmandi

2013-09-01

Full Text Available  In this paper, Ba0.5Sr0.5Co0.8Fe0.2O3-δ (BSCF thin films were deposited on single crystal SrTiO3 (STO (100 by pulsed laser deposition (PLD technique at different pressures of oxygen. Crystal structure of bulk and thin film samples was studied by x-ray diffraction (XRD. The XRD results indicate that both bulk and thin film samples have cubic structures. AFM micrographs showed an increase in RMS roughness by oxygen pressure. The electrical resistance was measured at room temperature up to 600 and 800 °C in air using four probe method for bulk and thin films, respectively. A sharp drop in resistance was observed by increasing temperature up to 400 °C, that was explained with the small polaron hopping model. Polaron activation energy was calculated by Arrhenius relation. It was decreased over increasing oxygen pressure. The surface exchange coefficient (Kchem of the 300 mTorr sample was measured by electrical conductivity relaxation (ECR technique. The results suggested a linear relationship between Kchem and reciprocal of absolute temperature.

Depositional environment of the Onverwacht sedimentary rocks Barberton greenstone belt, South Africa

Science.gov (United States)

Paris, I. A.

The Onverwacht Group is the basal part of the ca 3.5 Ga succession forming the Barberton greenstone belt. It comprises a volcanic pile overlain by a thin layer of volcaniclastic sediments which, due to silicification, are extremely well preserved. There has been a controversy as to how and in what environment these sediments were formed, different sets of data being presented to reach opposite conclusions. The Onverwacht Group has been extensively repeated tectonically and here for the first time, sediments from different structural levels are studied together. Three separate facies have been recognised, a distal and proximal turbidite facies and a subaerial facies. Deposition of Onverwacht Group sedimentary rocks occurred in an oceanic basin characterised by the presence of emergent volcanic islands. After eruption, material was deposited both subaerially and in a shallow submarine environment on the volcanic slopes and, as a result of pyroclastic flow, in the deeper parts of the basin.

Conductor of high electrical current at high temperature in oxygen and liquid metal environment

Science.gov (United States)

Powell, IV, Adam Clayton; Pati, Soobhankar; Derezinski, Stephen Joseph; Lau, Garrett; Pal, Uday B.; Guan, Xiaofei; Gopalan, Srikanth

2016-01-12

In one aspect, the present invention is directed to apparatuses for and methods of conducting electrical current in an oxygen and liquid metal environment. In another aspect, the invention relates to methods for production of metals from their oxides comprising providing a cathode in electrical contact with a molten electrolyte, providing a liquid metal anode separated from the cathode and the molten electrolyte by a solid oxygen ion conducting membrane, providing a current collector at the anode, and establishing a potential between the cathode and the anode.

Reconstructing the Holocene depositional environments along the northern coast of Sfax (Tunisia): Mineralogical and sedimentological approaches

Science.gov (United States)

Lamourou, Ali; Touir, Jamel; Fagel, Nathalie

2017-05-01

A sedimentological and mineralogical study of sedimentary cores allowed reconstructing the evolution of depositional environments along the Northern coast of Sfax (Tunisia). The aim of this research work is to identify the factors controlling the sedimentation from the Holocene to the Present time. Three 30-m sediment cores collected by drilling at 30 m water depth were analyzed for their color, magnetic susceptibility signal, grain size by laser diffraction, organic matter content by loss of ignition, carbonate content by calcimetry and mineralogy by X-ray diffraction on bulk powder and clay <2 μm. They broadly present the same sedimentological and mineralogical features. Microscopical observations of petrographic slides allowed identifying six main sedimentary facies. Bulk mineralogical assemblages comprised clay minerals, quartz, calcite, gypsum and K-feldspars were examined. Considerable change was observed in the carbonate content that mimicked the bioclaste abundance and diluted the detrital minerals (clay minerals, quartz and feldspars). The gypsum mainly occurred in the lower sedimentary columns (SC12 and SC9) and in the upper/middle of core SC6. The clay fraction was made of a mixture of kaolinite, illite, smectite and palygorskite with no clear variation through core depth. Both grain-size parameters and magnetic susceptibility profile showed a sharp transition in the upper 2-5 m of the sedimentological columns. Coarse, sandy to gravely sediments characterized by a low magnetic susceptibility signal were replaced by fine bioclastic-rich clayey sediments. The analysis of vertical succession of depositional facies revealed a fluvial depositional environment (coastal plain) basically marked by fluvial channels and inundation plains at the bottom of all cores. However, core-top sediments recorded a littoral marine environment with sand depositions rich in gastropods, lamellibranches and algæ. Depositional facies, sedimentological and mineralogical

Depleted uranium

International Nuclear Information System (INIS)

Huffer, E.; Nifenecker, H.

2001-02-01

This document deals with the physical, chemical and radiological properties of the depleted uranium. What is the depleted uranium? Why do the military use depleted uranium and what are the risk for the health? (A.L.B.)

Cat-CVD-prepared oxygen-rich μc-Si:H for wide-bandgap material

International Nuclear Information System (INIS)

Matsumoto, Yasuhiro; Ortega, Mauricio; Peza, Juan-Manuel; Reyes, Mario-Alfredo; Escobosa, Arturo

2005-01-01

Microcrystalline phase-involved oxygen-rich a-Si:H (hydrogenated amorphous silicon) films have been obtained using catalytic chemical vapor deposition (Cat-CVD) process. Pure SiH 4 (silane), H 2 (hydrogen), and O 2 (oxygen) gases were introduced in the chamber by maintaining a pressure of 0.1 Torr. A tungsten catalyzer was fixed at temperatures of 1750 and 1950 deg. C for film deposition on glass and crystalline silicon substrates at 200 deg. C. As revealed from X-ray diffraction spectra, the microcrystalline phase appears for oxygen-rich a-Si:H samples deposited at a catalyzer temperature of 1950 deg. C. However, this microcrystalline phase tends to disappear for further oxygen incorporation. The oxygen content in the deposited films was corroborated by FTIR analysis revealing Si-O-Si bonds and typical Si-H bonding structures. The optical bandgap of the sample increases from 2.0 to 2.7 eV with oxygen gas flow and oxygen incorporation to the deposited films. In the present thin film deposition conditions, no strong tungsten filament degradation was observed after a number of sample preparations

Update on the use of dissolved oxygen addition to monitor the effectiveness of noble metal applications in external manifolds

International Nuclear Information System (INIS)

Varela, J.A.; Huie, H.H.; Seeman, R.A.; Bourne, C.M.; Odell, A.D.

2014-01-01

Electrochemical corrosion potential (ECP) measurements in a Mitigation Monitoring System (MMS) ECP manifold have historically been a primary indicator of the effectiveness of an On-Line NobleChem™ (OLNC) application, with the MMS ECP intended to measure the catalytic effect of noble metal deposited on the ECP manifold surface. In some plants ECP measurements made on untreated surfaces prior to an OLNC application were significantly lower than what would be expected for stainless steel under reactor bulk chemistry conditions. This is due to the consumption and depletion of bulk liquid dissolved oxygen (DO) in the lines supplying reactor water to these external ECP measurement locations. This phenomenon degrades the ability to use these external manifolds to confirm noble metal deposition. Previous papers have described how the injection of an oxygen-rich stream to the MMS supply stream (DO Addition) can be used to re-establish the capability of external ECP measurements to monitor the catalytic behavior of platinum deposited during an OLNC injection. This paper will provide an update of how this method is being successfully used in operating BWRs to monitor OLNC injections. The paper will outline the overall approach used to characterize the catalytic behavior of external ECP manifolds before and after the noble metal application and present plant data collected during DO Additions performed under various conditions. (author)

Real-Time Molecular Monitoring of Chemical Environment in ObligateAnaerobes during Oxygen Adaptive Response

Energy Technology Data Exchange (ETDEWEB)

Holman, Hoi-Ying N.; Wozei, Eleanor; Lin, Zhang; Comolli, Luis R.; Ball, David. A.; Borglin, Sharon; Fields, Matthew W.; Hazen, Terry C.; Downing, Kenneth H.

2009-02-25

Determining the transient chemical properties of the intracellular environment canelucidate the paths through which a biological system adapts to changes in its environment, for example, the mechanisms which enable some obligate anaerobic bacteria to survive a sudden exposure to oxygen. Here we used high-resolution Fourier Transform Infrared (FTIR) spectromicroscopy to continuously follow cellular chemistry within living obligate anaerobes by monitoring hydrogen bonding in their cellular water. We observed a sequence of wellorchestrated molecular events that correspond to changes in cellular processes in those cells that survive, but only accumulation of radicals in those that do not. We thereby can interpret the adaptive response in terms of transient intracellular chemistry and link it to oxygen stress and survival. This ability to monitor chemical changes at the molecular level can yield important insights into a wide range of adaptive responses.

Turnover of eroded soil organic carbon after deposition in terrestrial and aquatic environments

DEFF Research Database (Denmark)

Kirkels, Frédérique; Cammeraat, Erik; Kalbitz, Karsten

cycling. However, the net effect on C fluxes between soils, inland waters and atmosphere remains uncertain. In this study, we determined SOC turnover in terrestrial and aquatic environments and indentified its major controls. A European gradient of agricultural sites was sampled, spanning a wide range...... soil properties (e.g. texture, aggregation, etc.), SOC quantity and quality. In a 16-week incubation experiment, SOC turnover was determined for conditions reflecting downslope soils or inland waters. Moreover, we studied the impact of labile C inputs (‘priming’) on SOC stability using 13C labeled...... cellulose. Physical and chemical soil properties and SOC molecular composition were assessed as potential controls on C turnover. SOC deposition in aquatic environments resulted in upto 3.5 times higher C turnover than deposition on downslope soils. Labile C inputs enlarged total CO2 emissions...

Forecasting the Depletion of Transboundary Groundwater Resources in Hyper-Arid Environments

Science.gov (United States)

Mazzoni, A.; Heggy, E.

2014-12-01

growth will be at unprecedented levels for these areas causing the water demand of these nations to grow largely. Our preliminary simulation results suggest that fossil aquifers cannot be used as a long-term solution for water shortage in hyper-arid environments. Aquifers in the Arabian Peninsula are forecasted to be depleted within decades.

EXPURT - a model for evaluating exposure from radioactive material deposited in the urban environment

International Nuclear Information System (INIS)

Crick, M.J.; Brown, J.

1990-06-01

This model, EXPURT (EXPosure from Urban Radionuclide Transfer), is described in detail. The model simulates the movement of activity deposited on various surfaces in the urban environment and, by taking into account the shielding properties of buildings and the habits of the population, evaluates the external doses to members of the population living in such urban environments, as a function of time after deposition. One of the other advantages of EXPURT over simpler models is that it can be used to assess the possible dose reductions that might be achieved by various decontamination techniques; for example, it can estimate the effectiveness of decontaminating roof surfaces alone in reducing exposure to individuals living in an urban environment. Sensitivity/uncertainty studies have been performed whereby those parameters contributing most to remaining uncertainty in the model's predictions of dose and dose rates were identified. Predictions of the EXPURT model were compared with those from a simpler external dose model in use at NRPB. (author)

Diesel autothermal reforming with hydrogen peroxide for low-oxygen environments

International Nuclear Information System (INIS)

Han, Gwangwoo; Lee, Sangho; Bae, Joongmyeon

2015-01-01

Highlights: • The concept of diesel reforming using hydrogen peroxide was newly proposed. • Characteristics of hydrogen peroxide was experimentally investigated. • Thermodynamically possible operating conditions were analyzed. • Catalytic performance of Ni–Ru/CGO for various diesel compounds was evaluated. • Long-term testing was successfully conducted using Korean commercial diesel. - Abstract: To operate fuel cells effectively in low-oxygen environments, such as in submarines and unmanned underwater vehicles, a hydrogen source with high hydrogen storage density is required. In this paper, diesel autothermal reforming (ATR) with hydrogen peroxide as an alternative oxidant is proposed as a hydrogen production method. Diesel fuel has higher hydrogen density than metal hydrides or other hydrocarbons. In addition, hydrogen peroxide can decompose into steam and oxygen, which are required for diesel ATR. Moreover, both diesel fuel and hydrogen peroxide are liquid states, enabling easy storage for submarine applications. Hydrogen peroxide exhibited the same characteristics as steam and oxygen when used as an oxidant in diesel reforming when pre-decomposition method was used. The thermodynamically calculated operating conditions were a steam-to-carbon ratio (SCR) of 3.0, an oxygen-to-carbon ratio (OCR) of 0.5, and temperatures below 700 °C to account for safety issues associated with hydrogen peroxide use and exothermic reactions. Catalytic activity and stability tests over Ni–Ru (19.5–0.5 wt.%)/Ce 0.9 Gd 0.1 O 2−x were conducted using various diesel compounds. Furthermore, long-term diesel ATR tests were conducted for 200 h using Korean commercial diesel. The degradation rate was 3.67%/100 h without the production of ethylene

Health and environmental problems of using depleted uranium

International Nuclear Information System (INIS)

Matousek, J.

2006-01-01

In the 1970's, a core of depleted uranium (DU) began to be introduced into the break through anti-tank munitions to enhance their effectiveness. The health and environmental threats of DU stem from the pyrophoric character of the core, burnt when penetrating armour to an aerosol of uranium oxides deposited in tissues after inhalation or ingestion. Their delayed effects are due to internal alpha irradiation by daughter products and toxicity of uranium. (authors)

The influence of oxygen exposure time on the composition of macromolecular organic matter as revealed by surface sediments on the Murray Ridge (Arabian Sea)

Science.gov (United States)

Nierop, Klaas G. J.; Reichart, Gert-Jan; Veld, Harry; Sinninghe Damsté, Jaap S.

2017-06-01

The Arabian Sea represents a prime example of an open ocean extended oxygen minimum zone (OMZ) with low oxygen concentrations (down to less than 2 μM) between 200 and 1000 m water depth. The OMZ impinges on the ocean floor, affecting organic matter (OM) mineralization. We investigated impact of oxygen depletion on the composition of macromolecular OM (MOM) along a transect through the OMZ on the slopes of the Murray Ridge. This sub-marine high in the northern Arabian Sea, with the top at approximately 500 m below sea surface (mbss), intersects the OMZ. We analyzed sediments deposited in the core of OMZ (suboxic conditions), directly below the OMZ (dysoxic conditions) and well below the OMZ (fully oxic conditions). The upper 18 cm of sediments from three stations recovered at different depths were studied. MOM was investigated by Rock Eval and flash pyrolysis techniques. The MOM was of a predominant marine origin and inferred from their pyrolysis products, most biomolecules (tetra-alkylpyrrole pigments, polysaccharides, proteins and their transformation products, and polyphenols including phlorotannins), showed a progressive relative degradation with increasing exposure to oxygen. Alkylbenzenes and, in particular, aliphatic macromolecules increased relatively. The observed differences in MOM composition between sediment deposited under various bottom water oxygen conditions (i.e. in terms of concentration and exposure time) was much larger than within sediment cores, implying that early diagenetic alteration of organic matter depends largely on bottom water oxygenation rather than subsequent anaerobic degradation within the sediments, even at longer time scales.

A comprehensive mathematical model of microscopic dose deposition in photodynamic therapy

International Nuclear Information System (INIS)

Kang-Hsin Wang, Ken; Mitra, Soumya; Foster, Thomas H.

2007-01-01

We have developed a comprehensive theoretical model for rigorously describing the spatial and temporal dynamics of oxygen ( 3 O 2 ) consumption and transport and microscopic photodynamic dose deposition during photodynamic therapy (PDT) in vivo. Previously published models have been improved by considering perfused vessels as a time-dependent 3 O 2 source and linking the 3 O 2 concentration in the vessel to that within the tissue through the Hill equation. The time-dependent photochemical 3 O 2 consumption rate incorporates sensitizer photobleaching effects and an experimentally determined initially nonuniform photosensitizer distribution. The axial transport of 3 O 2 is provided for in the capillaries and in the surrounding tissue. A self-sensitized singlet oxygen ( 1 O 2 )-mediated bleaching mechanism and the measured, initially nonuniform distribution of meso-tetrahydroxyphenyl chlorin at 3 h after intravascular administration were used to demonstrate the capabilities of the model. Time-evolved distributions of 3 O 2 concentration were obtained by numerically solving two-dimensional diffusion-with-reaction equations both in the capillary and the adjacent tissue. Using experimentally established physiological and photophysical parameters, the mathematical model allows computation of the dynamic variation of hemoglobin- 3 O 2 saturation (SO 2 ) within the vessels, irreversible sensitizer degradation due to photobleaching, and the microscopic distributions of 3 O 2 , sensitizer concentration, and 1 O 2 dose deposition under various irradiation conditions. The simulations reveal severe axial gradients in 3 O 2 and in photodynamic dose deposition in response to a wide range of clinically relevant treatment parameters. Thus, unlike former Krogh cylinder-based models, which assume a constant 3 O 2 concentration at the vessel, this new model identifies conditions in which 3 O 2 depletion and minimal deposition of reacting 1 O 2 exist near the end of axial segments of

Fish embryos on land: terrestrial embryo deposition lowers oxygen uptake without altering growth or survival in the amphibious fish Kryptolebias marmoratus.

Science.gov (United States)

Wells, Michael W; Turko, Andy J; Wright, Patricia A

2015-10-01

Few teleost fishes incubate embryos out of water, but the oxygen-rich terrestrial environment could provide advantages for early growth and development. We tested the hypothesis that embryonic oxygen uptake is limited in aquatic environments relative to air using the self-fertilizing amphibious mangrove rivulus, Kryptolebias marmoratus, which typically inhabits hypoxic, water-filled crab burrows. We found that adult mangrove rivulus released twice as many embryos in terrestrial versus aquatic environments and that air-reared embryos had accelerated developmental rates. Surprisingly, air-reared embryos consumed 44% less oxygen and possessed larger yolk reserves, but attained the same mass, length and chorion thickness. Water-reared embryos moved their opercula ∼2.5 more times per minute compared with air-reared embryos at 7 days post-release, which probably contributed to the higher rates of oxygen uptake and yolk utilization we observed. Genetically identical air- and water-reared embryos from the same parent were raised to maturity, but the embryonic environment did not affect growth, reproduction or emersion ability in adults. Therefore, although aspects of early development were plastic, these early differences were not sustained into adulthood. Kryptolebias marmoratus embryos hatched out of water when exposed to aerial hypoxia. We conclude that exposure to a terrestrial environment reduces the energetic costs of development partly by reducing the necessity of embryonic movements to dispel stagnant boundary layers. Terrestrial incubation of young would be especially beneficial to amphibious fishes that occupy aquatic habitats of poor water quality, assuming low terrestrial predation and desiccation risks. © 2015. Published by The Company of Biologists Ltd.

GEOLOGY AND DEPOSITIONAL ENVIRONMENT OF CAMPANO-MAASTRICHTIAN SEDIMENTS IN THE ANAMBRA BASIN, SOUTHEASTERN NIGERIA: EVIDENCE FROM FIELD RELATIONSHIP AND SEDIMENTOLOGICAL STUDY

Directory of Open Access Journals (Sweden)

A. E Salufu

2009-12-01

Full Text Available The study area lies within the Anambra Basin and it is made up of Enugu Shale, Mamu Formation, Ajali Sandstone, and Nsukka Formation. This study aimed at determining the geology and depositional environmental of these formations through field relationship and grain size distribution morphologic studies.The field data shows Enugu Shale as fissile, light grey with extraformational clast which graded into Mamu Formation whichis made up of shale, coal and sandy shale. It passes upward into Ajali Sandstone which is characterized by cross beds, Herringbonestructures and Ophiomorpha burrows. The youngest formation within the basin is Nsukka Formation.The granulometric study of Mamu Formation shows fine to medium grains, coarse, medium to fine grain for Mamu and Ajali Formation respectively. The standard deviation indicates poorly sorted. The kurtosis shows leptokurtic, platykurtic to very leptokurtic for both while the skewness values indicate positive and symmetrical in all except for Ajali Sandstone that is negatively skewed.The bivariate and the multivariate results reveal shallow marine and fluvial deposits for both Mamu Formation and Ajali Sandstone respectively. The paleocurrent direction of Ajali Sandstone indicates southwest while the provenance is northeast.The fissility of Enugu Shale suggests that it was deposited in low energy environment, distal to proximal lagoon environment.The presence of extraformatonal clast within Enugu Shale indicates fluvial incursion. However, the textural analysis of Mamu Formation suggests a sediment deposited in a low energy environment which favoured deposition of fine to medium size sediments that is, estuary environment. Textural result of Ajali Sandstone in the study area coupled with the field data such as Herring-bone structures, and Ophiomorpha burrows, revealed that Ajali Sandstone was deposited in a tidal environment probably littoral environment. While the light grey colour observed in the

A Search for O2 in CO-Depleted Molecular Cloud Cores With Herschel

Science.gov (United States)

Wirstroem, Eva S.; Charnley, Steven B.; Cordiner, Martin; Ceccarelli, Cecilia

2016-01-01

The general lack of molecular oxygen in molecular clouds is an outstanding problem in astrochemistry. Extensive searches with the Submillimeter Astronomical Satellite, Odin, and Herschel have only produced two detections; upper limits to the O2 abundance in the remaining sources observed are about 1000 times lower than predicted by chemical models. Previous atomic oxygen observations and inferences from observations of other molecules indicated that high abundances of O atoms might be present in dense cores exhibiting large amounts of CO depletion. Theoretical arguments concerning the oxygen gas-grain interaction in cold dense cores suggested that, if O atoms could survive in the gas after most of the rest of the heavy molecular material has frozen out onto dust, then O2 could be formed efficiently in the gas. Using Herschel HIFI, we searched a small sample of four depletion cores-L1544, L694-2, L429, and Oph D-for emission in the low excitation O2 N(sub J)?=?3(sub 3)-1(sub 2) line at 487.249 GHz. Molecular oxygen was not detected and we derive upper limits to its abundance in the range of N(O2)/N (H2) approx. = (0.6-1.6) x10(exp -7). We discuss the absence of O2 in the light of recent laboratory and observational studies.

Structural and optical properties of titanium dioxide films deposited by reactive magnetron sputtering in pure oxygen plasma

International Nuclear Information System (INIS)

Asanuma, T.; Matsutani, T.; Liu, C.; Mihara, T.; Kiuchi, M.

2004-01-01

Titanium dioxide (TiO 2 ) thin films were deposited on unheated quartz (SiO 2 ) substrates in 'pure oxygen' plasma by reactive radio-frequency (rf) magnetron sputtering. The structural and optical properties of deposited films were systematically studied by changing the deposition parameters, and it was very recently found that crystalline TiO 2 films grew effectively in pure O 2 atmosphere. For TiO 2 films deposited at a rf power P rf of 200 W, x-ray diffraction patterns show the following features: (a) no diffraction peak was observed at a total sputtering pressure p tot of 1.3 Pa; (b) rutile (110) diffraction was observed at 4.0 Pa, (c) the dominant diffraction was from anatase (101) planes, with additional diffraction from (200), under p tot between 6.7 and 13 Pa. For the deposition at 140 W, however, crystalline films with mixed phases were observed only between 4.0 and 6.7 Pa. The peaks of both the deposition rate and the anatase weight ratio for the films produced at 140 W were found at p tot of approximately 6.7 Pa. This suggests that the nucleation and growth of TiO 2 films were affected by the composition, density, and kinetic energy of the particles impinging on the substrate surface. The optical absorption edge analysis showed that the optical band gap E g and the constant B could sensitively detect the film growth behavior, and determine the film structure and optical absorption. The change in the shape of the fundamental absorption edge is considered to reflect the variation of density and the short-range structural modifications

Effects of ozone depletion and UV-B radiation on humans and the environment

Energy Technology Data Exchange (ETDEWEB)

Solomon, K.R. [Guelph Univ., ON (Canada). Centre for Toxicology

2008-03-15

This paper summarized current research related to the effects of ultraviolet (UV-B) radiation on human health and the environment. Effects included direct responses in human as well as effects on biogeochemistry and the environmental cycling of substances. UV radiation has many harmful effects on the skin, eyes, and immune systems of humans. Skin cancer is a leading cause of death among fair-skinned populations exposed to UV radiation. The role of UV radiation in cataract formation was discussed, as well as issues related to the suppression of immune responses. The link between sunlight exposure and vitamin D levels in human populations was examined. The effects of UV radiation on terrestrial and aquatic ecosystems were reviewed. Issues related to biogeochemistry and atmospheric processes were discussed. The review suggested that changes in the intensity of solar UV radiation due to ozone depletion will have important repercussions for all organisms on the planet. It was concluded that the combined effects of UV-B radiation and climate change will not be easy to predict. 201 refs., 4 figs.

Oxygen, hydrogen, sulfur, and carbon isotopes in the Pea Ridge magnetite-apatite deposit, southeast Missouri, and sulfur isotope comparisons to other iron deposits in the region

Science.gov (United States)

Johnson, Craig A.; Day, Warren C.; Rye, Robert O.

2016-01-01

Oxygen, hydrogen, sulfur, and carbon isotopes have been analyzed in the Pea Ridge magnetite-apatite deposit, the largest historic producer among the known iron deposits in the southeast Missouri portion of the 1.5 to 1.3 Ga eastern granite-rhyolite province. The data were collected to investigate the sources of ore fluids, conditions of ore formation, and provenance of sulfur, and to improve the general understanding of the copper, gold, and rare earth element potential of iron deposits regionally. The δ18O values of Pea Ridge magnetite are 1.9 to 4.0‰, consistent with a model in which some magnetite crystallized from a melt and other magnetite—perhaps the majority—precipitated from an aqueous fluid of magmatic origin. The δ18O values of quartz, apatite, actinolite, K-feldspar, sulfates, and calcite are significantly higher, enough so as to indicate growth or equilibration under cooler conditions than magnetite and/or in the presence of a fluid that was not entirely magmatic. A variety of observations, including stable isotope observations, implicate a second fluid that may ultimately have been meteoric in origin and may have been modified by isotopic exchange with rocks or by evaporation during storage in lakes.Sulfur isotope analyses of sulfides from Pea Ridge and seven other mineral deposits in the region reveal two distinct populations that average 3 and 13‰. Two sulfur sources are implied. One was probably igneous melts or rocks belonging to the mafic- to intermediate-composition volcanic suite that is present at or near most of the iron deposits; the other was either melts or volcanic rocks that had degassed very extensively, or else volcanic lakes that had trapped rising magmatic gases. The higher δ34S values correspond to deposits or prospects where copper is noteworthy—the Central Dome portion of the Boss deposit, the Bourbon deposit, and the Vilander prospective area. The correspondence suggests that (1) sulfur either limited the deposition

The Campylobacter jejuni RacRS system regulates fumarate utilization in a low oxygen environment

NARCIS (Netherlands)

van der Stel, Anne-Xander; van Mourik, Andries; Heijmen-van Dijk, Linda; Parker, Craig T; Kelly, David J; van de Lest, Chris H A; van Putten, Jos P M; Wosten, Marc

2015-01-01

The natural environment of the human pathogen Campylobacter jejuni is the gastrointestinal tract of warm-blooded animals. In the gut, the availability of oxygen is limited; therefore, less efficient electron acceptors such as nitrate or fumarate are used by C. jejuni. The molecular mechanisms that

Intensified Vegetation Water Use due to Soil Calcium Leaching under Acid Deposition

Science.gov (United States)

Lanning, M.; Wang, L.; Scanlon, T. M.; Vadeboncoeur, M. A.; Adams, M. B.; Epstein, H. E.; Druckenbrod, D.

2017-12-01

Despite the important role vegetation plays in the global water cycle, the exact controls of vegetation water use, especially the role of soil biogeochemistry, remain elusive. Nitrate and sulfate deposition from fossil fuel burning has caused significant soil acidification, leading to the leaching of soil base cations. From a physiological perspective, plants require various soil cations as signaling and regulatory ions as well as integral parts of structural molecules; a depletion of soil cations can cause reduced productivity and abnormal responses to environmental change. A deficiency in calcium could also potentially prolong stomatal opening, leading to increased transpiration until enough calcium had been acquired to stimulate stomatal closure. Based on the plant physiology and the nature of acidic deposition, we hypothesize that depletion of the soil calcium supply, induced by acid deposition, would intensify vegetation water use at the watershed scale. We tested this hypothesis by analyzing a long-term and unique data set (1989-2012) of soil lysimeter data along with stream flow and evapotranspiration data at the Fernow Experimental Forest. We show that depletion of soil calcium by acid deposition can intensify vegetation water use ( 10% increase in evapotranspiration and depletion in soil water) for the first time. These results are critical to understanding future water availability, biogeochemical cycles, and surficial energy flux and may help reduce uncertainties in terrestrial biosphere models.

Integration of rock physical signatures with depositional environments: A case study from East Coast of India

Science.gov (United States)

Mondal, Samit; Yadav, Ashok; Chatterjee, Rima

2018-01-01

Rock physical crossplots from different geological setup along eastern continental margin of India (ECMI) represent diversified signatures. To characterize the reservoirs in rock physics domain (velocity/modulus versus porosity) and then connecting the interpretation with geological model has been the objectives of the present study. Petrophysical logs (total porosity and volume of shale) from five wells located at sedimentary basins of ECMI have been analyzed to quantify the types of shale such as: laminated, dispersed and structural in reservoir. Presence of various shale types belonging to different depositional environments is coupled to define distinct rock physical crossplot trends for different geological setup. Wells from three different basins in East Coast of India have been used to capture diversity in depositional environments. Contact model theory has been applied to the crossplot to examine the change in rock velocity with change in reservoir properties like porosity and volume of shale. The depositional and diagenetic trends have been shown in the crossplot to showcase the prime controlling factor which reduces the reservoir porosity. Apart from that, the effect of geological factors like effective stress, sorting, packing, grain size uniformity on reservoir properties have also been focused. The rock physical signatures for distinct depositional environments, effect of crucial geological factors on crossplot trends coupled with established sedimentological models in drilled area are investigated to reduce the uncertainties in reservoir characterization for undrilled potentials.

Bioenergetic reprogramming plasticity under nitrogen depletion by the unicellular green alga Scenedesmus obliquus.

Science.gov (United States)

Papazi, Aikaterini; Korelidou, Anna; Andronis, Efthimios; Parasyri, Athina; Stamatis, Nikolaos; Kotzabasis, Kiriakos

2018-03-01

Simultaneous nitrogen depletion and 3,4-dichlorophenol addition induce a bioenergetic microalgal reprogramming, through strong Cyt b 6 f synthesis, that quench excess electrons from dichlorophenol's biodegradation to an overactivated photosynthetic electron flow and H 2 -productivity. Cellular energy management includes "rational" planning and operation of energy production and energy consumption units. Microalgae seem to have the ability to calculate their energy reserves and select the most profitable bioenergetic pathways. Under oxygenic mixotrophic conditions, microalgae invest the exogenously supplied carbon source (glucose) to biomass increase. If 3,4-dichlorophenol is added in the culture medium, then glucose is invested more to biodegradation rather than to growth. The biodegradation yield is enhanced in nitrogen-depleted conditions, because of an increase in the starch accumulation and a delay in the establishment of oxygen-depleted conditions in a closed system. In nitrogen-depleted conditions, starch cannot be invested in PSII-dependent and PSII-independent pathways for H 2 -production, mainly because of a strong decrease of the cytochrome b 6 f complex of the photosynthetic electron flow. For this reason, it seems more profitable for the microalga under these conditions to direct the metabolism to the synthesis of lipids as cellular energy reserves. Nitrogen-depleted conditions with exogenously supplied 3,4-dichlorophenol induce reprogramming of the microalgal bioenergetic strategy. Cytochrome b 6 f is strongly synthesized (mainly through catabolism of polyamines) to manage the electron bypass from the dichlorophenol biodegradation procedure to the photosynthetic electron flow (at the level of PQ pool) and consequently through cytochrome b 6 f and PSI to hydrogenase and H 2 -production. All the above showed that the selection of the appropriate cultivation conditions is the key for the manipulation of microalgal bioenergetic strategy that leads to

Metagenomic Study of Iron Homeostasis in Iron Depositing Hot Spring Cyanobacterial Community

Science.gov (United States)

Brown, I.; Franklin H.; Tringe, S. G.; Klatt, C. G.; Bryant, D. A.; Sarkisova, S. A.; Guevara, M.

2010-01-01

Introduction: It is not clear how an iron-rich thermal hydrosphere could be hospitable to cyanobacteria, since reduced iron appears to stimulate oxidative stress in all domains of life and particularly in oxygenic phototrophs. Therefore, metagenomic study of cyanobacterial community in iron-depositing hot springs may help elucidate how oxygenic prokaryotes can withstand the extremely high concentrations of reactive oxygen species (ROS) produced by interaction between environmental Fe2+ and O2. Method: Anchor proteins from various species of cyanobacteria and some anoxygenic phototrophs were selected on the basis of their hypothetical role in Fe homeostasis and the suppression of oxidative stress and were BLASTed against the metagenomes of iron-depositing Chocolate Pots and freshwater Mushroom hot springs. Results: BLASTing proteins hypothesized to be involved in Fe homeostasis against the microbiomes from the two springs revealed that iron-depositing hot spring has a greater abundance of defensive proteins such as bacterioferritin comigratory protein (Bcp) and DNA-binding Ferritin like protein (Dps) than a fresh-water hot spring. One may speculate that the abundance of Bcp and Dps in an iron-depositing hot spring is connected to the need to suppress oxidative stress in bacteria inhabiting environments with high Fe2+ concnetration. In both springs, Bcp and Dps are concentrated within the cyanobacterial fractions of the microbial community (regardless of abundance). Fe3+ siderophore transport (from the transport system permease protein query) may be less essential to the microbial community of CP because of the high [Fe]. Conclusion: Further research is needed to confirm that these proteins are unique to photoautotrophs such as those living in iron-depositing hot spring.

The potential importance of frost flowers, recycling on snow, and open leads for ozone depletion events

Directory of Open Access Journals (Sweden)

M. Piot

2008-05-01

Full Text Available We present model studies with the one-dimensional model MISTRA to investigate the potential role of frost flowers, recycling on snow, and open leads in the depletion of tropospheric ozone in the Arctic spring. In our model, we assumed frost flower aerosols to be the major source of bromine. We show that a major ozone depletion event can be satisfactorily reproduced only if the recycling on snow of deposited bromine into gas phase bromine is assumed. In the model, this cycling is more efficient than the bromine explosion process and maintains sufficiently high levels of bromine to deplete ozone down to few nmol mol⁻¹ within four days. We assessed the influence of different surface combinations (open lead/frost flowers on the chemistry in the model. Results showed noticeable modifications affecting the composition of aerosols and the deposition velocities. A model run with a series of coupled frost flower fields and open leads, separated by large areas of snow, showed results comparable with field observations. In addition, we studied the effects of modified temperature of either the frost flower field or the ambient airmass. A warmer frost flower field increases the relative humidity and the aerosol deposition rate. The deposition/re-emission process gains in importance, inducing more reactive bromine in the gas phase, and a stronger ozone depletion. A decrease of 1K in airmass temperature shows in our model that the aerosol uptake capacities of all gas phase species substantially increases, leading to enhanced uptake of acids from the gas phase. Consequently, the so-called bromine explosion accelerated and O₃ mixing ratios decreased. In our model representation, variations in wind speed affected the aerosol source function and influenced the amount of bromine in the atmosphere and thus the ozone depletion strength. Recent studies have suggested the important role of the precipitation of calcium carbonate (CaCO₃

Landscape characteristics of Rhizophora mangle forests and propagule deposition in coastal environments of Florida (USA)

Science.gov (United States)

Sengupta, R.; Middleton, B.; Yan, C.; Zuro, M.; Hartman, H.

2005-01-01

Field dispersal studies are seldom conducted at regional scales even though reliable information on mid-range dispersal distance is essential for models of colonization. The purpose of this study was to examine the potential distance of dispersal of Rhizophora mangle propagules by comparing deposition density with landscape characteristics of mangrove forests. Propagule density was estimated at various distances to mangrove sources (R. mangle) on beaches in southwestern Florida in both high-and low-energy environments, either facing open gulf waters vs. sheltered, respectively. Remote sensing and Geographic Information Systems were used to identify source forests and to determine their landscape characteristics (forest size and distance to deposition area) for the regression analyses. Our results indicated that increasing density of propagules stranded on beaches was related negatively to the distance of the deposition sites from the nearest stands of R. mangle and that deposition was greatly diminished 2 km or more from the source. Measures of fragmentation such as the area of the R. mangle forests were related to propagule deposition but only in low-energy environments. Our results suggest that geographic models involving the colonization of coastal mangrove systems should include dispersal dynamics at mid-range scales, i.e., for our purposes here, beyond the local scale of the forest and up to 5 km distant. Studies of mangrove propagule deposition at various spatial scales are key to understanding regeneration limitations in natural gaps and restoration areas. Therefore, our study of mid-range propagule dispersal has broad application to plant ecology, restoration, and modeling. ?? Springer 2005.

Incorporation of copper ions into crystals of T2 copper-depleted laccase from Botrytis aclada

International Nuclear Information System (INIS)

Osipov, E. M.; Polyakov, K. M.; Tikhonova, T. V.; Kittl, R.; Dorovatovskii, P.V.; Shleev, S. V.; Popov, V. O.; Ludwig, R.

2015-01-01

The restoration of the native form of laccase from B. aclada from the type 2 copper-depleted form of the enzyme was investigated. Copper ions were found to be incorporated into the active site after soaking the depleted enzyme in a Cu + -containing solution. Laccases belong to the class of multicopper oxidases catalyzing the oxidation of phenols accompanied by the reduction of molecular oxygen to water without the formation of hydrogen peroxide. The activity of laccases depends on the number of Cu atoms per enzyme molecule. The structure of type 2 copper-depleted laccase from Botrytis aclada has been solved previously. With the aim of obtaining the structure of the native form of the enzyme, crystals of the depleted laccase were soaked in Cu + - and Cu 2+ -containing solutions. Copper ions were found to be incorporated into the active site only when Cu + was used. A comparative analysis of the native and depleted forms of the enzymes was performed

Gamma exposures due to radionuclides deposited in urban environments: Pt. 1

International Nuclear Information System (INIS)

Meckbach, R.; Jacob, P.; Paretzke, H.G.

1988-01-01

The modification of gamma exposure from deposited activity at locations inside and outside of buildings in urban environments compared with unshielded locations has been computed using the Monte Carlo method. The types of buildings considered were a house of prefabricated parts, a semi-detached house, a row of four large terrace houses and a multistorey house block. The computations were performed for source energies of 0.3 MeV, 0.662 MeV and 3.0 MeV. In this first part of the paper results for the kerma at various locations inside and outside the buildings due to a contamination with unit surface activity are presented separately for each of the various deposition areas such as walls, windows, roofs, light shafts, paved areas, lawns, and trees. (author)

Biological nitrogen fixation in the oxygen-minimum region of the eastern tropical North Pacific ocean.

Science.gov (United States)

Jayakumar, Amal; Chang, Bonnie X; Widner, Brittany; Bernhardt, Peter; Mulholland, Margaret R; Ward, Bess B

2017-10-01

Biological nitrogen fixation (BNF) was investigated above and within the oxygen-depleted waters of the oxygen-minimum zone of the Eastern Tropical North Pacific Ocean. BNF rates were estimated using an isotope tracer method that overcame the uncertainty of the conventional bubble method by directly measuring the tracer enrichment during the incubations. Highest rates of BNF (~4 nM day -1 ) occurred in coastal surface waters and lowest detectable rates (~0.2 nM day -1 ) were found in the anoxic region of offshore stations. BNF was not detectable in most samples from oxygen-depleted waters. The composition of the N 2 -fixing assemblage was investigated by sequencing of nifH genes. The diazotrophic assemblage in surface waters contained mainly Proteobacterial sequences (Cluster I nifH), while both Proteobacterial sequences and sequences with high identities to those of anaerobic microbes characterized as Clusters III and IV type nifH sequences were found in the anoxic waters. Our results indicate modest input of N through BNF in oxygen-depleted zones mainly due to the activity of proteobacterial diazotrophs.

Effect of oxygen breathing on micro oxygen bubbles in nitrogen-depleted rat adipose tissue at sea level and 25 kPa altitude exposures

DEFF Research Database (Denmark)

Randsoe, Thomas; Hyldegaard, Ole

2012-01-01

The standard treatment of altitude decompression sickness (aDCS) caused by nitrogen bubble formation is oxygen breathing and recompression. However, micro air bubbles (containing 79% nitrogen), injected into adipose tissue, grow and stabilize at 25 kPa regardless of continued oxygen breathing...... at 101.3 kPa (sea level) or at 25 kPa altitude exposures during continued oxygen breathing. In keeping with previous observations and bubble kinetic models, we hypothesize that oxygen breathing may contribute to oxygen bubble growth at altitude. Anesthetized rats were exposed to 3 h of oxygen...... prebreathing at 101.3 kPa (sea level). Micro oxygen bubbles of 500-800 nl were then injected into the exposed abdominal adipose tissue. The oxygen bubbles were studied for up to 3.5 h during continued oxygen breathing at either 101.3 or 25 kPa ambient pressures. At 101.3 kPa, all bubbles shrank consistently...

nTiO_2 mass transfer and deposition behavior in an aquatic environment

International Nuclear Information System (INIS)

Wei, Xiuzhen; He, Junhui; Wang, Meng; Fang, Jinfeng; Chen, Jinyuan; Lv, Bosheng

2016-01-01

Nano-TiO_2 (nTiO_2) is widely used in industry, and some of it is inevitably released into natural aquatic environments. nTiO_2 can be deposited on the streambed or transported along the stream and streambed, and it can also undergo exchange-transfer processes in these systems. The behavior of nTiO_2 in rivers includes deposition-transfer processes in the stream and exchange-transfer processes between the stream and streambed. In this work, the deposition, mass transfer, exchange, and aggregation behavior of nTiO_2 in a simulated river were studied as a function of the solution pH, stream velocity, and anionic, cationic, and neutral surfactant concentrations. In these experiments, a recirculating flume was used to simulate a natural stream. The nTiO_2 deposition and aggregation phenomena in the river and streambed were characterized. Of the three surfactants studied, the anionic surfactant enhanced the nTiO_2 stability in the river and limited its aggregation most effectively, resulting in slow nTiO_2 deposition and nTiO_2 transport over long distances. This study provides information about nanoparticle transport phenomena in simulated natural aquatic systems.

Depositional environments of the uranium bearing Cutler Formations, Lisbon Valley, Utah

International Nuclear Information System (INIS)

Campbell, J.A.; Steele-Mallory, B.A.

1979-01-01

The Cutler Formation in Lisbon Valley, San Juan County, Utah, is composed predominantly of fluvial arkosic sandstones, siltstones, shales, and mudstones that were deposited by meandering streams that flowed across a flood plain and tidal flat close to sea level. Two types of channel deposits are recognized from their sedimentary structures: meandering and distributary. The flood plain was occasionally transgressed by a shallow sea from the west, resulting in the deposition of several thin limestones and marine sandstones. The marine sandstones were deposited as longshore bars. Wind transported sand along the shoreline of the shallow sea, forming a coastal dune field. Marine sandstones and eolian sandstones are more common in the upper Cutler in the southern part of the area, whereas in the central and northern part of the area the formation is predominantly fluvial. Crossbed orientation indicates that Cutler streams flowed S. 67 0 W. on the average, whereas marine currents moved sediment S. 36 0 E. and N. 24 0 W., and wind transported sand S. 80 0 E. The uranium in the Cutler is found in the central and northern part of the area, in the upper part of the formation, in small fluvial sandstone bodies that were deposited predominantly in a distributary environment. No uranium is known in the marine or eolian sandstones. Petrographically, the uranium-bearing sandstones are identical to other Cutler fluvial sandstones except that they contain less calcite and more clay and are slightly coarser grained. Ore formation has modified the host sandstones very little

Depositional environments of the uranium-bearing Cutler Formations, Lisbon Valley, Utah

Science.gov (United States)

Campbell, John A.; Steele-Mallory, Brenda A.

1979-01-01

The Cutler Formation in Lisbon Valley, San Juan County, Utah, is composed predominantly of fluvial arkosic sandstones, siltstones, shales, and mudstones that were deposited by meandering streams that flowed across a flood plain and tidal flat close to sea level. Two types of channel deposits are recognized from their sedimentary structures: meandering and distributary. The flood plain was occasionally transgressed by a shallow sea from the west, resulting in the deposition of several thin limestones and marine sandstones. The marine sandstones were deposited as longshore bars. Wind transported sand along the shoreline of the shallow sea, forming a coastal dune field. Marine sandstones and eolian sandstones are more common in the upper Cutler in the southern part of the area, whereas in the central and northern part of the area the formation is predominantly fluvial. Crossbed orientation indicates that Cutler streams flowed S. 67? W. on the the average, whereas marine currents moved sediment S. 36? E. and N. 24? W., and wind transported sand S. 800 E. The uranium in the Cutler is found in the central and northern part of the area, in the upper part of the formation, in small fluvial sandstone bodies that were deposited predominantly in a distributary environment. No uranium is known in the marine or eolian sandstones. Petrographically, the uranium-bearing sandstones are identical to other Cutler fluvial sandstones except that they contain less calcite and more clay and are slightly coarser grained. Ore formation has modified the host sandstones very little.

Influence of dissolved oxygen concentration on the toxicity of potassium cyanide to rainbow trout. [Salmo gairdneri

Energy Technology Data Exchange (ETDEWEB)

Downing, K M

1954-01-01

The present work was undertaken to see if similar results were obtained when fish were tested in a continuous flow of water in which the concentrations of oxygen and cyanide were kept constant. Periods of survival were measured this way to minimize distortion of results by accumulation of metabolic waste, depletion of oxygen or depletion of poison. Results are summarized as follows: rainbow trout survival in potassium cyanide increased with increase in dissolved oxygen; increase in survival times did not decline as oxygen saturation was approached; and medium survival times of 3.3 minutes or less were normally distributed while those of greater than 13 minutes were log normally distributed. 6 references, 1 figure.

Er2O3 coating by reactive magnetron sputtering: Effect of oxygen supply and erbium pre-layer deposition

Directory of Open Access Journals (Sweden)

P.A. Rayjada

2016-12-01

The film grows in mixed phase of cubic and monoclinic structures when erbium metal pre-layer is deposited on the P91 steel substrate and in pure monoclinic phase in absence of the pre-layer. Post annealing seems to partially convert monoclinic into cubic phase in the mixed phase coating. Better crystallization and slightly more surface roughness is observed in the sample processed with higher oxygen to argon ratio. DC resistivity is found in 1015Ω*cm range and it is marginally more in the sample processed with more oxygen. The spectroscopic ellipsometry on these films to obtain optical dielectric properties gives encouraging results in terms of close match of the thickness and roughness values with those obtained from SEM and AFM respectively. Systematic study of optical dielectric property suggests a trend consistent with DC resistivity.

Determination of hydraulic conductivity from grain-size distribution for different depositional environments

KAUST Repository

Rosas, Jorge

2013-06-06

Over 400 unlithified sediment samples were collected from four different depositional environments in global locations and the grain-size distribution, porosity, and hydraulic conductivity were measured using standard methods. The measured hydraulic conductivity values were then compared to values calculated using 20 different empirical equations (e.g., Hazen, Carman-Kozeny) commonly used to estimate hydraulic conductivity from grain-size distribution. It was found that most of the hydraulic conductivity values estimated from the empirical equations correlated very poorly to the measured hydraulic conductivity values with errors ranging to over 500%. To improve the empirical estimation methodology, the samples were grouped by depositional environment and subdivided into subgroups based on lithology and mud percentage. The empirical methods were then analyzed to assess which methods best estimated the measured values. Modifications of the empirical equations, including changes to special coefficients and addition of offsets, were made to produce modified equations that considerably improve the hydraulic conductivity estimates from grain size data for beach, dune, offshore marine, and river sediments. Estimated hydraulic conductivity errors were reduced to 6 to 7.1m/day for the beach subgroups, 3.4 to 7.1m/day for dune subgroups, and 2.2 to 11m/day for offshore sediments subgroups. Improvements were made for river environments, but still produced high errors between 13 and 23m/day. © 2013, National Ground Water Association.

Determination of hydraulic conductivity from grain-size distribution for different depositional environments

KAUST Repository

Rosas, Jorge; Lopez Valencia, Oliver Miguel; Missimer, Thomas M.; Coulibaly, Kapo M.; Dehwah, Abdullah; Sesler, Kathryn; Rodri­ guez, Luis R. Lujan; Mantilla, David

2013-01-01

Over 400 unlithified sediment samples were collected from four different depositional environments in global locations and the grain-size distribution, porosity, and hydraulic conductivity were measured using standard methods. The measured hydraulic conductivity values were then compared to values calculated using 20 different empirical equations (e.g., Hazen, Carman-Kozeny) commonly used to estimate hydraulic conductivity from grain-size distribution. It was found that most of the hydraulic conductivity values estimated from the empirical equations correlated very poorly to the measured hydraulic conductivity values with errors ranging to over 500%. To improve the empirical estimation methodology, the samples were grouped by depositional environment and subdivided into subgroups based on lithology and mud percentage. The empirical methods were then analyzed to assess which methods best estimated the measured values. Modifications of the empirical equations, including changes to special coefficients and addition of offsets, were made to produce modified equations that considerably improve the hydraulic conductivity estimates from grain size data for beach, dune, offshore marine, and river sediments. Estimated hydraulic conductivity errors were reduced to 6 to 7.1m/day for the beach subgroups, 3.4 to 7.1m/day for dune subgroups, and 2.2 to 11m/day for offshore sediments subgroups. Improvements were made for river environments, but still produced high errors between 13 and 23m/day. © 2013, National Ground Water Association.

Terrestrial ozone depletion due to a Milky Way gamma-ray burst

Science.gov (United States)

Thomas, Brian C.

Gamma-Ray Bursts (GRBs) are short, incredibly powerful astrophysical events which produce a flux of radiation detectable across the observable universe. A GRB within our own galaxy could cause major damage to the Earth's biosphere. Rate estimates suggest that at least one GRB has occurred within a dangerous range (about 2 kpc) in the last billion years. The gamma radiation from such a burst would quickly deplete much of the Earth's protective ozone layer, allowing an increase in solar UVB radiation reaching the surface. This radiation is harmful to life, causing sunburn and damaging DNA. In addition, NO 2 produced in the atmosphere would cause a decrease in visible sunlight reaching the surface and could cause global cooling. Nitric acid rain could stress portions of the biosphere, but the increased nitrate deposition could be helpful to land plants. We have used a two-dimensional atmospheric model to investigate the effects on the Earth's atmosphere of a GRB. We have simulated bursts delivering a range of fluences, at various latitudes, at the equinoxes and solstices, and at different times of day. We have computed DNA damage caused by increased solar UVB radiation, reduction in solar visible light due to NO 2 opacity; and deposition of nitrates through rainout of HNO 3 . For a "typical" burst in the last billion years, we find globally averaged ozone depletion up to 38%. Localized depletion reaches as much as 74%. Significant global depletion (at least 10%) persists up to about 7 years after the burst. Our results depend strongly on time of year and latitude over which the burst occurs. We find DNA damage of up to 16 times the normal annual global average, with greatest damage occurring at low to mid latitudes. We find reductions in visible sunlight of a few percent, primarily in the polar regions. Nitrate deposition similar to or slightly greater than that currently caused by lightning is also observed. We find support in our results for the hypothesis that the

The influence of oxygen partial pressure on material properties of Eu{sup 3+}-doped Y{sub 2}O{sub 2}S thin film deposited by Pulsed Laser Deposition

Energy Technology Data Exchange (ETDEWEB)

Ali, A.G., E-mail: aliag@qwa.ufs.ac.za [Department of Physics, University of the Free State (Qwaqwa Campus), Private Bag X13, Phuthaditjhaba 9866 (South Africa); Dejene, B.F. [Department of Physics, University of the Free State (Qwaqwa Campus), Private Bag X13, Phuthaditjhaba 9866 (South Africa); Swart, H.C. [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein 9300 (South Africa)

2016-01-01

Eu{sup 3+}-doping has been of interest to improve the luminescent characteristics of thin-film phosphors. Y{sub 2}O{sub 2}S:Eu{sup 3+} films have been grown on Si (100) substrates by using a Pulsed Laser Deposition technique. The thin films grown under different oxygen deposition pressure conditions have been characterized using structural and luminescent measurements. The X-ray diffraction patterns showed mixed phases of cubic and hexagonal crystal structures. As the oxygen partial pressure increased, the crystallinity of the films improved. Further increase of the O{sub 2} pressure to 140 mtorr reduced the crystallinity of the film. Similarly, both scanning electron microscopy and Atomic Force Microscopy confirmed that an increase in O{sub 2} pressure affected the morphology of the films. The average band gap of the films calculated from diffuse reflectance spectra using the Kubelka–Munk function was about 4.75 eV. The photoluminescence measurements indicated red emission of Y{sub 2}O{sub 2}S:Eu{sup 3+} thin films with the most intense peak appearing at 619 nm, which is assigned to the {sup 5}D{sub 0}–{sup 7}F{sub 2} transition of Eu{sup 3+}. This most intense peak was totally quenched at higher O{sub 2} pressures. This phosphor may be a promising material for applications in the flat panel displays.

Near-room temperature deposition of W and WO3 thin films by hydrogen atom assisted chemical vapor deposition

International Nuclear Information System (INIS)

Lee, W.W.; Reeves, R.R.

1992-01-01

A novel near-room temperatures CVD process has been developed using H-atoms reaction with WF 6 to produced tungsten and tungsten oxide films. The chemical, physical and electrical properties of these films were studied. Good adhesion and low resistivity of W films were measured. Conformal WO 3 films were obtained on columnar tungsten using a small amount of molecular oxygen in the gas stream. A reaction mechanism was evaluated on the basis of experimental results. The advantages of the method include deposition of adherent films in a plasma-free environment, near-room temperature, with a low level of impurity

Post-deposition treatments of plasma-sprayed YBaCuO coatings deposited on nickel

Energy Technology Data Exchange (ETDEWEB)

Dube, D; Lambert, P; Arsenault, B; Champagne, B [National Research Council of Canada, Boucherville, PQ (Canada)

1990-12-15

As-sprayed YBaCuO coatings do not exhibit superconductivity because of the non-equilibrium solidification conditions of molten particles on the substrate and to the deposit's loss of oxygen. Therefore post-deposition treatments are required to restore the superconductivity. In this study, post-deposition treatments were carried out on thick YBaCuO coatings (200 {mu}m) deposited on cold nickel substrates to modify their microstructure, to restore the oxygen content and to improve their superconducting properties. These treatments consist in heating the coatings at various temperatures above 950deg C followed by controlled solidification cycles. The effect of these treatments on the microstructure of the coatings was assessed and the interaction between the coatings and the nickel substrate was also examined. Solidification cycles including a low cooling rate near the non-congruent melting temperature of YBa{sub 2}Cu{sub 3}O{sub x} and involving a temperature gradient were carried out to create a texture. (orig.).

Biogas - agriculture and environment

Energy Technology Data Exchange (ETDEWEB)

Knudsen, L; Birkmose, T [The Danish Agricultural Advisory Centre, Aarhus (Denmark)

1997-08-01

Cultivating the soil always leads to a higher loss of nutrients to the surrounding environment than the loss recorded from natural areas. Loss of nitrogen by leaching may have the effect that the set limit for nitrate of 50 mg NO{sub 3} per litre of water is exceeded in areas, where the water supply is based on ground water. Furthermore, nitrogen leaching may lead to eutrophication followed by oxygen depletion in inland waterways whereas it has hardly any significant environmental impact in freshwater areas. Ammonia volatilization followed by deposition influences nutrient-poor bio-topes like heaths, marshland etc. Increasing importance is attached to the loss of phosphorus from farmland as the discharge of sewage from urban areas and industries are reduced due to effective chemical and biological treatment plants. Environmental problems related to loss phosphorus is primarily eutrophication of freon water lakes. Nitrous oxide(N{sub 2}O), resulting from denitrification of nitrate in the soil, and the emission of methane contribute considerably to the greenhouse effect. Both nitrous oxide and the emission of methane are influenced by the volume of animal production, but no certain data on the connection and the importance are available. Loss of nutrients from farm production is primarily related to animal production. The largest environmental impact concerns the loss of nutrients in areas, where the live-stock production is very intensive in large compact areas and, where the produced amount of nutrients in animal manure and other organic manures exceed the requirements of the crops. (EG) 13 refs.

Biogas - agriculture and environment

International Nuclear Information System (INIS)

Knudsen, L.; Birkmose, T.

1997-01-01

Cultivating the soil always leads to a higher loss of nutrients to the surrounding environment than the loss recorded from natural areas. Loss of nitrogen by leaching may have the effect that the set limit for nitrate of 50 mg NO 3 per litre of water is exceeded in areas, where the water supply is based on ground water. Furthermore, nitrogen leaching may lead to eutrophication followed by oxygen depletion in inland waterways whereas it has hardly any significant environmental impact in freshwater areas. Ammonia volatilization followed by deposition influences nutrient-poor bio-topes like heaths, marshland etc. Increasing importance is attached to the loss of phosphorus from farmland as the discharge of sewage from urban areas and industries are reduced due to effective chemical and biological treatment plants. Environmental problems related to loss phosphorus is primarily eutrophication of freon water lakes. Nitrous oxide(N 2 O), resulting from denitrification of nitrate in the soil, and the emission of methane contribute considerably to the greenhouse effect. Both nitrous oxide and the emission of methane are influenced by the volume of animal production, but no certain data on the connection and the importance are available. Loss of nutrients from farm production is primarily related to animal production. The largest environmental impact concerns the loss of nutrients in areas, where the live-stock production is very intensive in large compact areas and, where the produced amount of nutrients in animal manure and other organic manures exceed the requirements of the crops. (EG) 13 refs

Permafrost oxygen isotope ratios and chronology of three cores from Antarctica

International Nuclear Information System (INIS)

Stuiver, M.; Yang, I.C.; Denton, G.H.

1976-01-01

It is stated that permafrost core sediments, associated with the last intrusion of the Ross Ice Shelf in the New Harbour region, were deposited in marine (0 - 85 m deep) as well as freshwater environments (100 - 125 m). Oxygen isotope ratio measurements on these cores provide palaeoclimatic information and show that the extension of the Ross Ice Shelf predates 150,000 yr BP, whereas the radiocarbon date of its retreat is about 5,800 yr b.p. (author)

Uranium distribution and sandstone depositional environments: oligocene and upper Cretaceous sediments, Cheyenne basin, Colorado

International Nuclear Information System (INIS)

Nibbelink, K.A.; Ethridge, F.G.

1984-01-01

Wyoming-type roll-front uranium deposits occur in the Upper Cretaceous Laramie and Fox Hills sandstones in the Cheyenne basin of northeastern Colorado. The location, geometry, and trend of specific depositional environments of the Oligocene White River and the Upper Cretaceous Laramie and Fox Hills formations are important factors that control the distribution of uranium in these sandstones. The Fox Hills Sandstone consists of up to 450 ft (140 m) of nearshore marine wave-dominated delta and barrier island-tidal channel sandstones which overlie offshore deposits of the Pierre Shale and which are overlain by delta-plain and fluvial deposits of the Laramie Formation. Uranium, which probably originated from volcanic ash in the White River Formation, was transported by groundwater through the fluvial-channel deposits of the White River into the sandstones of the Laramie and Fox Hills formations where it was precipitated. Two favorable depositional settings for uranium mineralization in the Fox Hills Sandstone are: (1) the landward side of barrier-island deposits where barrier sandstones thin and interfinger with back-barrier organic mudstones, and (2) the intersection of barrier-island and tidal channel sandstones. In both settings, sandstones were probably reduced during early burial by diagenesis of contained and adjacent organic matter. The change in permeability trends between the depositional strike-oriented barrier sandstones and the dip-oriented tidal-channel sandstones provided sites for dispersed groundwater flow and, as demonstrated in similar settings in other depositional systems, sites for uranium mineralization

Tuning Nanocrystal Surface Depletion by Controlling Dopant Distribution as a Route Toward Enhanced Film Conductivity

Science.gov (United States)

Staller, Corey M.; Robinson, Zachary L.; Agrawal, Ankit; Gibbs, Stephen L.; Greenberg, Benjamin L.; Lounis, Sebastien D.; Kortshagen, Uwe R.; Milliron, Delia J.

2018-05-01

Electron conduction through bare metal oxide nanocrystal (NC) films is hindered by surface depletion regions resulting from the presence of surface states. We control the radial dopant distribution in tin-doped indium oxide (ITO) NCs as a means to manipulate the NC depletion width. We find in films of ITO NCs of equal overall dopant concentration that those with dopant-enriched surfaces show decreased depletion width and increased conductivity. Variable temperature conductivity data shows electron localization length increases and associated depletion width decreases monotonically with increased density of dopants near the NC surface. We calculate band profiles for NCs of differing radial dopant distributions and, in agreement with variable temperature conductivity fits, find NCs with dopant-enriched surfaces have narrower depletion widths and longer localization lengths than those with dopant-enriched cores. Following amelioration of NC surface depletion by atomic layer deposition of alumina, all films of equal overall dopant concentration have similar conductivity. Variable temperature conductivity measurements on alumina-capped films indicate all films behave as granular metals. Herein, we conclude that dopant-enriched surfaces decrease the near-surface depletion region, which directly increases the electron localization length and conductivity of NC films.

Effect of oxygen flow rate on ITO thin films deposited by facing targets sputtering

International Nuclear Information System (INIS)

Kim, Youn J.; Jin, Su B.; Kim, Sung I.; Choi, Yoon S.; Choi, In S.; Han, Jeon G.

2010-01-01

Tin-doped indium oxide (ITO) thin films were deposited on glass substrates at various oxygen flow rates using a planar magnetron sputtering system with facing targets. In this system, the strong internal magnets inside the target holders confine the plasma between the targets. High resolution transmission electron microscopy revealed a combination of amorphous and crystalline phases on the glass substrate. X-ray photoelectron spectroscopy suggested that the decrease in carrier concentration and increase in mobility were caused by a decrease in the concentration of Sn 4+ states. The electrical and optical properties of the ITO films were examined by Hall measurements and UV-visible spectroscopy, which showed a film resistivity and transmittance of 4.26 x l0 -4 Ω cm, and > 80% in the visible region, respectively.

Oxygen sensitization of mammalian cells under different irradiation conditions

International Nuclear Information System (INIS)

Ling, C.C.; Michaels, H.B.; Gerweck, L.E.; Epp, E.R.; Peterson, E.C.

1981-01-01

The oxygen dependence of the radiosensitivity of cultured CHO cells was examined in detail with particular attention paid to avoiding possible artifacts due to radiolytic oxygen depletion. Two methods of gas equilibration and irradiation were used. In the first approach, cells were irradiated with 50-kVp X rays in a thin-layer geometry which offered maximum interchange between the cells and the surrounding gas. The second technique employed 280-kVp X irradiation of cells under full-medium conditions with mechanical agitation to minimize the effect of radiochemical oxygen consumption by promoting rapid oxygen replenishment. With these techniques oxygen radiosensitization was clearly resolved at an oxygen concentration of 0.03% in the gas phase. The oxygen K curves measured by these two methods were similar in shape over a wide range of oxygen concentration

Influence of oxygen pressure and aging on LaAlO3 films grown by pulsed laser deposition on SrTiO3 substrates

KAUST Repository

Park, Jihwey

2014-02-24

The crystal structures of LaAlO3 films grown by pulsed laser deposition on SrTiO3 substrates at oxygen pressure of 10−3 millibars or 10−5 millibars, where kinetics of ablated species hardly depend on oxygen background pressure, are compared. Our results show that the interface between LaAlO3 and SrTiO3 is sharper when the oxygen pressure is lower. Over time, the formation of various crystalline phases is observed while the crystalline thickness of the LaAlO3 layer remains unchanged. X-ray scattering as well as atomic force microscopy measurements indicate three-dimensional growth of such phases, which appear to be fed from an amorphous capping layer present in as-grown samples.

Bipolar performance of the electroplated iron-nickel deposits for water electrolysis

International Nuclear Information System (INIS)

Hu, C.-C.; Wu, Y.-R.

2003-01-01

The activities of oxygen and hydrogen evolution on Fe-Ni deposits with controllable compositions were systematically compared in the alkaline media. The redox behavior of Fe-Ni deposits prior to oxygen evolution could be generally related to their electrochemical activity for the oxygen evolution reaction meanwhile the activity of hydrogen evolution was found to be generally proportional to the mean roughness factor of deposits. Fe 24 Ni 76 , Fe 76 Ni 24 and Fe 90 Ni 10 deposits simultaneously exhibiting good activities of oxygen and hydrogen evolution were employed as electrode materials for water electrolysis in a bipolar hydrogen-oxygen electrolyzer in the stability test, examined at 50 and 200 mA cm -2 in 5 M KOH for 2 weeks. The morphological, compositional and crystalline information of these three materials before and after the bipolar studies were measured by scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectroscopy and X-ray diffraction (XRD) analysis, respectively. These studies demonstrated the potential applicability of these three deposits in the bipolar electrolyzer for water electrolysis

Oxygen source-oriented control of atmospheric pressure chemical vapor deposition of VO2 for capacitive applications

Directory of Open Access Journals (Sweden)

Dimitra Vernardou

2016-06-01

Full Text Available Vanadium dioxides of different crystalline orientation planes have successfully been fabricated by chemical vapor deposition at atmospheric pressure using propanol, ethanol and O2 gas as oxygen sources. The thick a-axis textured monoclinic vanadium dioxide obtained through propanol presented the best electrochemical response in terms of the highest specific discharge capacity of 459 mAh g-1 with a capacitance retention of 97 % after 1000 scans under constant specific current of 2 A g-1. Finally, the electrochemical impedance spectroscopy indicated that the charge transfer of Li+ through the vanadium dioxide / electrolyte interface was easier for this sample enhancing significantly its capacitance performance.

Mineral deposits of the Silica plateau – evaluation of selected geological factors of the environment

Directory of Open Access Journals (Sweden)

BalហBartolomej

2001-12-01

Full Text Available The Silica plateau is a part of a greatest karst area in the Slovak republic - Protected Landscape Area Slovak karst (CHKO Slovenský kras. Karst areas belong to the most sensitive environments, from the point of view of impacts caused by anthropogenous activities. This area reacts sensitively, disturbing the environmental balance caused by mining of mineral deposits. Three mineral deposits of industrial rocks: one deposit of decorative stone - Silická Brezová and two deposits of building stone – Silická Brezová I and Lipovník, respectively, were registered on January 1-st, 2001 in the territory of the Silica plateau. Some deposits utilized in the past namely two deposits of building raw materials (Hrušov and Krásnohorská Dlhá Lúka and one Pb-Zn ore deposit (Ardovo are also mentioned and evaluated in the paper. From the point of view of economical potential of the area, mineral deposits have a character of geopotentials. However the utilization of deposits represents negative anthropogenous impact. When compared with another forms of optimal and rational utilization of the country, e.g. agriculture, forestry, water management, construction, tourism etc., mineral deposits have a character of geobarriers. This research was carried out in the frame of the VEGA Grant No. 1/6090/1999.

An evolving magmatic-hydrothermal system in the formation of the Mesozoic Meishan magnetite-apatite deposit in the Ningwu volcanic basin, eastern China

Science.gov (United States)

Liu, Wen-Hao; Jiang, Man-Rong; Zhang, Xiao-Jun; Xia, Yan; Algeo, Thomas J.; Li, Huan

2018-06-01

The Meishan iron deposit contains 338 Mt of iron-ore reserves at 39% Fe and represents the largest magnetite-apatite deposit in the Ningwu Basin of eastern China. Controversy has long existed about whether this deposit had a hydrothermal or iron-oxide melt origin. Iron mineralization is genetically related to plutons that are composed of gabbro-diorite, which were emplaced at 130 ± 1 Ma. These rocks have SiO2 contents of 51.72-54.60 wt%, Na2O contents of 3.47-4.04 wt%, K2O contents of 2.02-2.69 wt%, and K2O/Na2O ratios of 0.51-0.73. These rocks are enriched in LILEs and LREEs and depleted in Nb, Ta, and Ti, which indicates that the magma originated through partial melting of an enriched lithospheric mantle source in a subduction environment. A pattern of decreasing initial Sr isotopic ratios and increasing εNd(t) values with time in Early Cretaceous magmatic rocks of the Ningwu Basin may indicate incorporation of increasing proportions of asthenospheric mantle material into the source magma, which is consistent with the processes of lithospheric thinning and asthenospheric upwelling in eastern China related to Mesozoic subduction of the Paleo-Pacific Plate. Two stages of magnetite are found in the gabbro-diorite: (1) early-crystallized magnetite as euhedral-subhedral crystals in larger clinopyroxene crystals, and (2) later-crystallized magnetite and accompanying ilmenite grains in the voids between plagioclase and clinopyroxene crystals. The formation of magnetite before clinopyroxene, combined with the results of Fe-Ti oxide geothermometry and analysis of magnetite V content, indicates that the oxygen fugacity of the source magma was greater than ΔFMQ +2.2 at an early stage (>640 °C) but decreased to ΔFMQ -2.66 as abundant magnetite crystallized at a later stage (∼489 °C). The early crystallization of magnetite at a high oxygen fugacity does not support a Fenner evolution trend for the primitive magma and diminishes the likelihood of liquid immiscibility

The evolutionary puzzle of egg size, oxygenation and parental care in aquatic environments.

Science.gov (United States)

Braga Goncalves, Ines; Ahnesjö, Ingrid; Kvarnemo, Charlotta

2015-08-22

Offspring fitness generally improves with increasing egg size. Yet, eggs of most aquatic organisms are small. A common but largely untested assumption is that larger embryos require more oxygen than they can acquire through diffusion via the egg surface, constraining egg size evolution. However, we found no detrimental effects of large egg size on embryo growth and survival under hypoxic conditions. We tested this in the broad-nosed pipefish, Syngnathus typhle, whose males provide extensive care (nourishment, osmoregulation and oxygenation) to their young in a brood pouch on their bodies. We took advantage of this species' pronounced variation in egg size, correlating positively with female size, and tested the effect of hypoxia (40% dissolved oxygen) versus fully oxygenated (100%) water on embryo size and survival of large versus small eggs after 18 days of paternal brooding. Egg size did not affect embryo survival, regardless of O2 treatment. While hypoxia affected embryo size negatively, both large and small eggs showed similar reductions in growth. Males in hypoxia ventilated more and males with large eggs swam more, but neither treatment affected their position in the water column. Overall, our results call into question the most common explanation for constrained egg size evolution in aquatic environments. © 2015 The Author(s).

Measuring aerosols generated inside armoured vehicles perforated by depleted uranium ammunition

International Nuclear Information System (INIS)

Parkhurst, M.A.

2003-01-01

In response to questions raised after the Gulf War about the health significance of exposure to depleted uranium (DU), the US Department of Defense initiated a study designed to provide an improved scientific basis for assessment of possible health effects on soldiers in vehicles struck by these munitions. As part of this study, a series of DU penetrators were fired at an Abrams tank and a Bradley fighting vehicle, and the aerosols generated by vehicle perforation were collected and characterised. A robust sampling system was designed to collect aerosols in this difficult environment and monitor continuously the sampler flow rates. The aerosol samplers selected for these tests included filter cassettes, cascade impactors, a five-stage cyclone and a moving filter. Sampler redundancy was an integral part of the sampling system to offset losses from fragment damage. Wipe surveys and deposition trays collected removable deposited particulate matter. Interior aerosols were analysed for uranium concentration and particle size distribution as a function of time. They were also analysed for uranium oxide phases, particle morphology and dissolution in vitro. These data, currently under independent peer review, will provide input for future prospective and retrospective dose and health risk assessments of inhaled or ingested DU aerosols. This paper briefly discusses the target vehicles, firing trajectories, aerosol samplers and instrumentation control systems, and the types of analyses conducted on the samples. (author)

EXPERIMENTAL ACIDIFICATION CAUSES SOIL BASE-CATION DEPLETION AT THE BEAR BROOK WATERSHED IN MAINE

Science.gov (United States)

There is concern that changes in atmospheric deposition, climate, or land use have altered the biogeochemistry of forests causing soil base-cation depletion, particularly Ca. The Bear Brook Watershed in Maine (BBWM) is a paired watershed experiment with one watershed subjected to...

Deposition of radionuclides and their subsequent relocation in the environment following an accidental release to the atmosphere

International Nuclear Information System (INIS)

Underwood, B.Y.; Roed, J.; Paretzke, H.G.

1993-01-01

The objective of the project is to improve, as necessary, the models and parameterizations used in estimating the intensity and spatial distribution of deposited activity, and the total health/economic impact of such deposits in assessments of the consequences of accidental releases of radioactivity. The study comprises the influence of various weather conditions on deposition; the resuspension of deposited 137 Cs activity; the weathering of deposits in urban and rural environments; the ultimate fate and dosimetric impact of radionuclides carried by urban run-off water; the impact of the atmosphere's dispersion capabilities. Objectives and results of the four contributions to the project for the reporting period are presented. (R.P.) 5 refs., 4 figs., 1 tab

Tracking Reactive Nitrogen Sources, Chemistry and Deposition in Urban Environments Using Stable Isotopes

Science.gov (United States)

Hastings, M. G.; Clark, S. C.; Chai, J.; Joyce, E.; Miller, D. J.; Schiebel, H.; Walters, W.

2017-12-01

Reactive nitrogen (Nr) includes compounds such as nitrogen oxides (NOx, HONO), ammonia (NH3), nitrate (NO3-), ammonium (NH4+), and organic nitrates. These compounds serve major roles in controlling the composition of our atmosphere, and have a direct impact on ecosystem health and water quality. Our research is focused on using stable isotopes of Nr to investigate variations in sources, chemistry, atmospheric transport, and deposition. Our aim is to fingerprint distinct emission sources - such as vehicles, power plants, aircraft, agriculature, wildfires, and lightning - and track their influence in the environment. We have recently characterized vehicle emission plumes, emissions from agricultural soils under different management practices, and (in the near future) wildfire plumes in the western U.S. Our approach targets characterizing the isotopic composition of NOx, HONO, and NH3 at both the emissions source and the plume scale. In contrast to large ranges found for individual tailpipe emissions of NOx, on-road plumes in the U.S. have a mean δ15N of -4.7 ± 1.7‰. The plume scale approach integrates across the typical U.S. fleet giving a representative value that can be used for tracking the impact of this emission source in the environment. NH3 also tends towards a narrow isotopic range when considered at the roadside scale compared to individual vehicles. In agricultural settings, the isotopes of NOx and HONO released from soils under different fertilizer practices is typically very negative in δ15N (-40 to -10‰) and appears to vary most with soil N properties rather than meteorology. Our work is now extending to discern sources influencing Nr deposition in an urban area at the head of New England's largest estuary. National monitoring of N deposition shows decreases in NO3- (but not NH4+) deposition over the last two decades, following better controls on NOx emissions. Wet deposition collected in an urban area exhibits N concentrations that are often 3

Pulsed 1064 nm Nd-YAG Laser Deposition of Titanium on Silicon in a Nitrogen Environment

Directory of Open Access Journals (Sweden)

Wilson Garcia

1999-12-01

Full Text Available Pulsed laser deposition (PLD technique was demonstrated for the deposition of titanium nitride (TiN thin films on Si (100 substrates. A 1064 nm pulsed Nd-YAG laser is focused on a titanium (99.5% target in a nitrogen environment to generate the atomic flux needed for the film deposition. Spectroscopic analysis of the plasma emission indicates the presence of atomic titanium and nitrogen, which are the precursors of TiN. Images of the films grown at different laser pulse energies show an increase in the number and size of deposited droplets and clusters with increasing laser pulse energy. A decrease in cluster and droplet size is also observed, with an increase in substrate temperature. EDS data show an increase in the titanium peak relative to the silicon as the ambient nitrogen pressure is decreased. An increase in deposition time was found to result in large clusters and irregularly shaped structures on the substrate. Post-deposition annealing of the samples enhanced the crystallinity of the film.

Geological-economic analysis on the exploration of backup resources for depleted mines in Lujing uranium ore-field, central-southern China

International Nuclear Information System (INIS)

Li Deping; Wang Zhicheng; Fan Shaoyun

2006-01-01

With the geological-economic evaluation program for pithead heap-leaching mining uranium deposits developed by the authors and the data of column-leaching tests and the geological reserve, the geological-economic evaluation is made to the residual geological reserves of both Lujing and Huangfengling deposit, and the geological reserves of Yangjiaonao deposit of the depleted mines in Lujing uranium ore-field, central-southern China. The results of static analysis on these reserves show that the residual geological reserves of both Lujing and Huangfengling deposit belong to sub-profitable type, but the ones of Yangjiaonao deposit is profitable with 26.56% tax-before profit. 1 tU profitable type of ore from Yangjiaonao deposit can use 2.40-3.79 tU subprofitable type of ores from Lujing and Huangfengling deposit. In order to solving the problem on scarcity of backup resources of the depleted mines in Lujing uranium ore-field and using the existing sub-profitable type of geological reserves, it is suggested that the high grade of profitable type of deposits should be explored around the exhausting mines so that the production of the mines could be profitable by the pithead heap-leaching mining method with arrangement groups of both sub-profitable and profitable type of ores. (authors)

Sensibility analysis of fuel depletion using different nuclear fuel depletion codes

Energy Technology Data Exchange (ETDEWEB)

Martins, F.; Velasquez, C.E.; Castro, V.F.; Pereira, C.; Silva, C. A. Mello da, E-mail: felipmartins94@gmail.com, E-mail: carlosvelcab@hotmail.com, E-mail: victorfariascastro@gmail.com, E-mail: claubia@nuclear.ufmg.br, E-mail: clarysson@nuclear.ufmg.br [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Departamento de Engenharia Nuclear

2017-07-01

Nowadays, the utilization of different nuclear codes to perform the depletion and criticality calculations has been used to simulated nuclear reactors problems. Therefore, the goal is to analyze the sensibility of the fuel depletion of a PWR assembly using three different nuclear fuel depletion codes. The burnup calculations are performed using the codes MCNP5/ORIGEN2.1 (MONTEBURNS), KENO-VI/ORIGEN-S (TRITONSCALE6.0) and MCNPX (MCNPX/CINDER90). Each nuclear code performs the burnup using different depletion codes. Each depletion code works with collapsed energies from a master library in 1, 3 and 63 groups, respectively. Besides, each code uses different ways to obtain neutron flux that influences the depletions calculation. The results present a comparison of the neutronic parameters and isotopes composition such as criticality and nuclides build-up, the deviation in results are going to be assigned to features of the depletion code in use, such as the different radioactive decay internal libraries and the numerical method involved in solving the coupled differential depletion equations. It is also seen that the longer the period is and the more time steps are chosen, the larger the deviation become. (author)

Sensibility analysis of fuel depletion using different nuclear fuel depletion codes

International Nuclear Information System (INIS)

Martins, F.; Velasquez, C.E.; Castro, V.F.; Pereira, C.; Silva, C. A. Mello da

2017-01-01

Nowadays, the utilization of different nuclear codes to perform the depletion and criticality calculations has been used to simulated nuclear reactors problems. Therefore, the goal is to analyze the sensibility of the fuel depletion of a PWR assembly using three different nuclear fuel depletion codes. The burnup calculations are performed using the codes MCNP5/ORIGEN2.1 (MONTEBURNS), KENO-VI/ORIGEN-S (TRITONSCALE6.0) and MCNPX (MCNPX/CINDER90). Each nuclear code performs the burnup using different depletion codes. Each depletion code works with collapsed energies from a master library in 1, 3 and 63 groups, respectively. Besides, each code uses different ways to obtain neutron flux that influences the depletions calculation. The results present a comparison of the neutronic parameters and isotopes composition such as criticality and nuclides build-up, the deviation in results are going to be assigned to features of the depletion code in use, such as the different radioactive decay internal libraries and the numerical method involved in solving the coupled differential depletion equations. It is also seen that the longer the period is and the more time steps are chosen, the larger the deviation become. (author)

Modeling the oxygen microheterogeneity of tumors for photodynamic therapy dosimetry

Science.gov (United States)

Pogue, Brian W.; Paulsen, Keith D.; O'Hara, Julia A.; Hoopes, P. Jack; Swartz, Harold

2000-03-01

Photodynamic theory of tumors uses optical excitation of a sensitizing drug within tissue to produce large deposits of singlet oxygen, which are thought to ultimately cause the tumor destruction. Predicting dose deposition of singlet oxygen in vivo is challenging because measurement of this species in vivo is not easily achieved. But it is possible to follow the concentration of oxygen in vivo, and so measuring the oxygen concentration transients during PDT may provide a viable method of estimating the delivered dose of singlet oxygen. However modeling the microscopic heterogeneity of the oxygen distribution within a tumor is non-trivial, and predicting the microscopic dose deposition requires further study, but this study present the framework and initial calibration needed or modeling oxygen transport in complex geometries. Computational modeling with finite elements provides a versatile structure within which oxygen diffusion and consumption can be modeled within realistic tissue geometries. This study develops the basic tools required to simulate a tumor region, and examines the role of (i) oxygen supply and consumption rates, (ii) inter- capillary spacing, (iii) photosensitizer distribution, and (iv) differences between simulated tumors and those derived directly from histology. The result of these calculations indicate that realistic tumor tissue capillary networks can be simulated using the finite element method, without excessive computational burden for 2D regions near 1 mm2, and 3D regions near 0.1mm3. These simulations can provide fundamental information about tissue and ways to implement appropriate oxygen measurements. These calculations suggest that photodynamic therapy produces the majority of singlet oxygen in and near the blood vessels, because these are the sites of highest oxygen tension. These calculations support the concept that tumor vascular regions are the major targets for PDT dose deposition.

Depositional environments and porosity distribution in regressive limestone reservoirs of the Mishrif Formation, Southern Iraq

International Nuclear Information System (INIS)

AlDabbas, Moutaz; AlJassim Jassim; AlJumaily Saad

2010-01-01

Eight subsurface sections and a large number of thin sections of the Mishrif Limestone were studied to unravel the depositional facies and environments. The allochems in the Mishrif Formation are dominated by bioclasts, whereas peloids, ooids, and intraclasts are less abundant. The sedimentary microfacies of the Mishrif Formation includes mudstone, wackestone, packstone, grainstone, floatstone, and rudstone, which have been deposited in basinal, outer shelf, slop followed by shoal reef and lagoonal environments. The formation displays various extents of dolomitization and is cemented by calcite and dolomite. The formation has gradational contact with the underlying Rumaila Formation but is unconformably overlain by the Khasib Formation. The unconformity is recognized because the skeletal grains are dominated by Chaophyta (algae), which denotes the change of environment from fully marine to lacustrine environment. Thus, the vertical bioclast analysis indicates that the Mishrif Formation is characterized by two regressive cycles, which control the distribution of reservoir quality as well as the patterns of calcite and dolomite cement distribution. Mishrif Formation gradationally overlies Rumaila Formation. This was indicated by the presence of the green parts of Chaophyta (algae) as main skeletal grains at the uppermost part of well Zb-47, which refer to lacustrine or fresh water environment. Petrographical study shows that the fossils, peloids, oolitis, and intraclasts represent the main allochem. Calcite and dolomite (as diagenetic products) are the predominant mineral components of Mishrif Formation. Fossils were studied as an environmental age and facial boundaries indicators, which are located in a chart using personal computer programs depending on their distributions on the first appearance of species. Fifteen principal sedimentary microfacies have been identified in the Mishrif Formation, which includes lime mudstone, mudstone-wackestone, wackestone

Electro-deposition of Pd on Carbon paper and Ni foam via surface limited redox-replacement reaction for oxygen reduction reaction

International Nuclear Information System (INIS)

Modibedi, Remegia M.; Mathe, Mkhulu K.; Motsoeneng, Rapelang G.; Khotseng, Lindiwe E.; Ozoemena, Kenneth I.; Louw, Eldah K.

2014-01-01

Pd nanostructured catalysts were electrodeposited by surface-limited redox replacement reactions using the electrochemical atomic layer deposition technique. Carbon paper and Ni foam were used as substrates for the electrodeposition of the metal. Supported nanostructured Pd electrodes were characterized using electrochemical methods and scanning electron microscopy. Carbon paper and Ni foam produced good quality deposits with some agglomeration on Ni foam. The EDX profiles confirmed the presence of Pd particles. Cyclic voltammograms of the electrodeposited Pd on substrates showed features characteristic of polycrystalline Pd electrodes. In the acidic electrolyte a very weak oxygen reduction reaction (ORR) activity was observed on Pd/Carbon paper electrode when compared to Pd/Ni foam electrode. The Pd/Ni foam electrode showed improved ORR activity in alkaline medium

Geochemical partitioning of lead in biogenic carbonate sediments in a coral reef depositional environment

International Nuclear Information System (INIS)

Horta-Puga, Guillermo

2017-01-01

The fate of trace elements in reef depositional environments has not been extensively investigated. The aim of this study was to determine the partitioning of Pb in sediments of the Veracruz Reef System, and its relation to local environmental sources. Lead was determined in four geochemical fractions: exchangeable (3.8 ± 0.4 μg g −1 ), carbonate (57.0 ± 13.6 μg g −1 ), organic matter (2.0 ± 0.9 μg g −1 ), and mineral (17.5 ± 5.4 μg g −1 ). For the mineral fraction, lead concentrations were higher in those reefs influenced by river discharge or by long-distance transport of terrigenous sediments. The bioavailable concentration of lead (range: 21.9–85.6 μg g −1 ) indicates that the Veracruz Reef System is a moderately polluted area. As expected, the carbonate fraction contained the highest proportion of Pb (70%), and because the reef framework is largely made up of by biogenic carbonate sediments, hence, it is therefore the most important repository of Pb in coral reef depositional environments. - Highlights: • Lead concentrations were determined in four geochemical fractions of reef sediments. • The carbonate fraction accounted for > 70% of the content of Pb in reef sediments. • Terrigenous sediments are the main source of Pb associated to the mineral fraction. • The Veracruz Reef System is considered a moderately polluted area. • Sediments are the main repositories of lead in coral reef depositional environments.

Berau coal in East Kalimantan; Its petrographics characteristics and depositional environment

Directory of Open Access Journals (Sweden)

Nana Suwarna

2014-06-01

Full Text Available http://dx.doi.org/10.17014/ijog.vol2no4.20071To asses the characteristics of the Early to Middle Miocene Berau coal in the Berau Basin, leading to interpretation of coal depositional environments, some fresh outcrop and subcrop samples and also drill cores of the coals have been analyzed microscopically. Coal petrographic analysis was performed on twenty four coal samples from the Middle Miocene Lati Formation. Vitrinite, present in a high value, and ranging between 66.2 - 96.2%, is dominated by vitrinite B. On the other hand, inertinite and exinite, showing a similar value, exist in a low to moderate amount. Vitrinite reflectance, present in a low value, varies from 0.40 - 0.58%. Low mineral matter content is dominated by clay minerals (0.4 - 6.6% with minor pyrite. Transitions from wet and very wet forested swamps to drier conditions with lower tree density are indicated by the higher content of vitrinite B, whilst a reverse trend is indicated by the lower content of vitrinite A. Petrographic indices obtained from facies diagnostic macerals show that an accumulation of the ancient peats under prevailing relatively wet limited influx clastic marsh to very wet forest swamps or moors is considered. The composition of the coal samples supports the interpretation of a system of fluvial to meandering streams in an upper delta plain environment. The original peat-forming vegetation was composed mainly of cellulose rich, shrub-like plants, tree ferns, herbaceous plant communities, with minor amount of trees. Thereby, the organic facies concept is thus applicable in basin studies context and has potential to become an additional tool for depositional environment interpretation.  

Role of Mineral Deposits in Global Geochemical Cycles

Science.gov (United States)

Kesler, S.; Wilkinson, B.

2009-12-01

contributions to the near-surface global copper cycle and, for porphyry copper deposits, is approximately 13,000 times larger than the rate at which Earth concentrates copper in them. Preliminary estimates for mineral deposits containing gold yield similar results, suggesting that these relations apply to most metals that are concentrated into hydrothermal mineral deposits. These comparisons indicate that erosion of mineral deposits is a small but important contributor to the natural near-surface flux of metals. Anthropogenic removal and dispersal of metals into the surface environment (mining) is several orders of magnitude larger, and is likely to result in depletion of mineral deposits from the upper few kilometers of Earth’s crust within the next few thousand years.

Local Measurement of Fuel Energy Deposition and Heat Transfer Environment During Fuel Lifetime Using Controlled Calorimetry

International Nuclear Information System (INIS)

Don W. Miller; Andrew Kauffmann; Eric Kreidler; Dongxu Li; Hanying Liu; Daniel Mills; Thomas D. Radcliff; Joseph Talnagi

2001-01-01

A comprehensive description of the accomplishments of the DOE grant titled, ''Local Measurement of Fuel Energy Deposition and Heat Transfer Environment During Fuel Lifetime using Controlled Calorimetry''

"When the going gets tough, who keeps going?" Depletion sensitivity moderates the ego-depletion effect.

Science.gov (United States)

Salmon, Stefanie J; Adriaanse, Marieke A; De Vet, Emely; Fennis, Bob M; De Ridder, Denise T D

2014-01-01

Self-control relies on a limited resource that can get depleted, a phenomenon that has been labeled ego-depletion. We argue that individuals may differ in their sensitivity to depleting tasks, and that consequently some people deplete their self-control resource at a faster rate than others. In three studies, we assessed individual differences in depletion sensitivity, and demonstrate that depletion sensitivity moderates ego-depletion effects. The Depletion Sensitivity Scale (DSS) was employed to assess depletion sensitivity. Study 1 employs the DSS to demonstrate that individual differences in sensitivity to ego-depletion exist. Study 2 shows moderate correlations of depletion sensitivity with related self-control concepts, indicating that these scales measure conceptually distinct constructs. Study 3 demonstrates that depletion sensitivity moderates the ego-depletion effect. Specifically, participants who are sensitive to depletion performed worse on a second self-control task, indicating a stronger ego-depletion effect, compared to participants less sensitive to depletion.

When the Going Gets Tough, Who Keeps Going? Depletion Sensitivity Moderates the Ego-Depletion Effect

Directory of Open Access Journals (Sweden)

Stefanie J. Salmon

2014-06-01

Full Text Available Self-control relies on a limited resource that can get depleted, a phenomenon that has been labeled ego-depletion. We argue that individuals may differ in their sensitivity to depleting tasks, and that consequently some people deplete their self-control resource at a faster rate than others. In three studies, we assessed individual differences in depletion sensitivity, and demonstrate that depletion sensitivity moderates ego-depletion effects. The Depletion Sensitivity Scale (DSS was employed to assess depletion sensitivity. Study 1 employs the DSS to demonstrate that individual differences in sensitivity to ego-depletion exist. Study 2 shows moderate correlations of depletion sensitivity with related self-control concepts, indicating that these scales measure conceptually distinct constructs. Study 3 demonstrates that depletion sensitivity moderates the ego-depletion effect. Specifically, participants who are sensitive to depletion performed worse on a second self-control task, indicating a stronger ego-depletion effect, compared to participants less sensitive to depletion.

Effect of Different Post Deposition Annealing Treatments on Properties of Zinc Oxide Thin Films

Directory of Open Access Journals (Sweden)

Arti Arora

2010-06-01

Full Text Available Two different post deposition annealing atmospheres of oxygen and forming gas have been investigated for the improvement of rf sputtered zinc oxide thin films. The results show that type of atmosphere (oxidant o reduction plays an important role in the changes observed in structural, electrical and optical properties. It has been found that the structural properties of rf sputtered zinc oxide films improve in all the annealing environments. The intensity and grain size increases as the annealing temperature increases. It has been found that films become stress free at lowest temperature in oxygen as compare to forming gas annealing. The zinc oxide films annealed in oxygen shows sufficient resistivity associated to high transmittance (83 % characteristics required for MEMS based acoustic devices.

Oxygen incorporation into GST phase-change memory matrix

Energy Technology Data Exchange (ETDEWEB)

Golovchak, R., E-mail: holovchakr@apsu.edu [Department of Physics and Astronomy, Austin Peay State University, Clarksville, TN 37044 (United States); Choi, Y.G. [Department of Materials Science and Engineering, Korea Aerospace University, Gyeonggi 412-791 (Korea, Republic of); Kozyukhin, S. [Kurnakov Institute of General and Inorganic Chemistry of RAS, 31 Leninsky Pr., Moscow 119991 (Russian Federation); National Research Tomsk State University, 36 Lenin Pr., Tomsk 634050 (Russian Federation); Chigirinsky, Yu. [Scientific-Research Physicotechnical Institute at the Nizhnii Novgorod State University, Nizhnii Novgorod 603600 (Russian Federation); Kovalskiy, A.; Xiong-Skiba, P.; Trimble, J. [Department of Physics and Astronomy, Austin Peay State University, Clarksville, TN 37044 (United States); Pafchek, R.; Jain, H. [Department of Materials Science and Engineering, Lehigh University, 5 East Packer Avenue, Bethlehem, PA 18015-3195 (United States)

2015-03-30

Graphical abstract: - Highlights: • Surfaces of GST-225 films are depleted in Te as a result of the reaction with oxygen. • Top layers of oxidized GST-225 are formed by Sb and Ge oxide complexes. • Depth profiles of Sb and Ge oxide complexes are found to be different. • Crystallization at 300 °C in O{sub 2} atmosphere leads to Ge redistribution. - Abstract: Structural changes in amorphous and crystallized GST-225 films induced by the reaction with oxygen are studied at different depth scales. The mechanism of interaction of the very top surface layers with oxygen is studied with low-energy ion scattering (LEIS) technique, while the modifications of chemistry in the underlying surface layers are investigated with high-resolution X-ray photoelectron spectroscopy (XPS). The changes averaged through the overall film thickness are characterized by micro-Raman spectroscopy. The oxygen exposure leads to a depletion of GST-225 film surfaces in Te and formation of the antimony and germanium oxides. The antimony oxide complexes are found throughout the whole thickness of the films after their prolonged storage in air, whereas no evidence for formation of pure GeO{sub 2} phase is found in the volume of the films through Raman spectroscopy. A tendency to form Ge-rich phase within the ∼10 nm surface layer is additionally observed by LEIS profiling during crystallization of GST-225 film at 300 °C in oxygen atmosphere.

OZONE DEPLETING SUBSTANCES ELIMINATION MANAGEMENT: THE SUCCESS STORY OF MACEDONIA

Directory of Open Access Journals (Sweden)

Margarita Matlievska

2013-04-01

Full Text Available Man, with its activities, produces and uses substances that have negative impact on the environment and the human health, and can cause an economic damage. Consequently, they have a great impact on quality of life. Among the most harmful chemicals are Ozone Depleting Substances that are subject of regulation with international conventions. This Paper supports the fact that each country has to undertake national efforts for ozone depleting substances reduction and elimination. In that respect, the general objective of the Paper is to present the Macedonian unique experience regarding its efforts to reduce or eliminate these substances. The following two aspects were subject to the research: national legislation which regulates the Ozone Depleting Substances import and export as well as the implementation of the projects that resulted with the elimination of Ozone Depleting Substances quantities in the period 1995 – 2010. The research outcomes confirm the starting research hypothesis i.e. that with adequately created and implemented national action, the amount of Ozone Depleting Substances consumption can dramatically fall.

Behavior and role of superficial oxygen in Cu for the growth of large single-crystalline graphene

Energy Technology Data Exchange (ETDEWEB)

Ding, Dong [Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, Fukuoka 816-8580 (Japan); Solís-Fernández, Pablo [Global Innovation Center (GIC), Kyushu University, Fukuoka, 816-8580 (Japan); Yunus, Rozan Mohamad [Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, Fukuoka 816-8580 (Japan); Hibino, Hiroki [School of Science and Technology, Kwansei Gakuin University, Hyogo, 669-1337 (Japan); Ago, Hiroki, E-mail: ago.hiroki.974@m.kyushu-u.ac.jp [Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, Fukuoka 816-8580 (Japan); Global Innovation Center (GIC), Kyushu University, Fukuoka, 816-8580 (Japan)

2017-06-30

Highlights: • Growth mechanism of large graphene grains on oxidized Cu was revealed by investigating the behavior of oxygen in the Cu. • Only the heating up step was found to be crucial for obtaining large graphene grains. • The copper oxide layer was found to promote some oxygen atoms to dissolve into the Cu foil. • The dissolved oxygen contributes to the reduction of a nucleation density of graphene. - Abstract: Decreasing the nucleation density of graphene grown on copper (Cu) foil by chemical vapor deposition (CVD) is essential for the synthesis of large-area single-crystalline graphene. Here, the behavior of the copper oxide layer and its impact on the graphene growth have been investigated. We found that a small amount of oxygen dissolves into the Cu when the oxide layer decomposes during the heating up in a non-reducing Ar environment. The remaining oxygen in the Cu foil can play an important role in decreasing the graphene nucleation density. The dissolved oxygen can withstand at high temperatures even in reducing H{sub 2} environments without completely losing its effectiveness for maintaining a low graphene nucleation density. However, heating up in a H{sub 2} environment significantly reduces the copper oxide layer during the very first moments of the process at low temperatures, preventing the oxygen to dissolve into the Cu and significantly increasing the nucleation density. These findings will help to improve the graphene growth on Cu catalyst by increasing the grain size while decreasing the grain density.

Electron-stimulated purification of platinum nanostructures grown via focused electron beam induced deposition

Directory of Open Access Journals (Sweden)

Brett B. Lewis

2015-04-01

Full Text Available Platinum–carbon nanostructures deposited via electron beam induced deposition from MeCpPt(IVMe3 are purified during a post-deposition electron exposure treatment in a localized oxygen ambient at room temperature. Time-dependent studies demonstrate that the process occurs from the top–down. Electron beam energy and current studies demonstrate that the process is controlled by a confluence of the electron energy loss and oxygen concentration. Furthermore, the experimental results are modeled as a 2nd order reaction which is dependent on both the electron energy loss density and the oxygen concentration. In addition to purification, the post-deposition electron stimulated oxygen purification process enhances the resolution of the EBID process due to the isotropic carbon removal from the as-deposited materials which produces high-fidelity shape retention.

Improving the characteristics of Sn-doped In2O2 grown at room temperature with oxygen radical-assisted electron beam deposition

Science.gov (United States)

Oh, Min-Suk; Seo, Inseok

2017-07-01

Sn-doped In2O3 (Indium tin oxide, ITO) is widely utilized in numerous industrial applications due to its high electrical conductivity and high optical transmittance in the visible region. High quality ITO thin-films have been grown at room temperature by oxygen radical assisted e-beam evaporation without any post annealing or plasma treatment. The introduction of oxygen radicals during e-beam growth greatly improved the surface morphology and structural properties of the ITO films. The obtained ITO film exhibits higher carrier mobility of 43.2 cm2/V·s and larger optical transmittance of 84.6%, resulting in a higher figure of merit of ˜ 2.8 × 10-2 Ω-1, which are quite comparable to the ITO film deposited by conventional e-beam evaporation. These results show that ITO films grown by oxygen radical assisted e-beam evaporation at room temperature with high optical transmittance and high electron conductivity have a great potential for organic optoelectronic devices.

Microfacies characteristics, sedimentary environments and sequence stratigraphy of Upper Cretaceous deposits in northwest of Nehbandan (Basiran section

Directory of Open Access Journals (Sweden)

Mohammad nabi Gorgij

2015-10-01

Full Text Available Introduction   The Basiran stratigraphic section is located about 160 km northwest of Nehbandan.The section was measured in detail at 59 06 30 N and 31 52 50 E. Nehbandan area with respect to fourfold geological subdivision of Iran is part of Central Iran that is located in the eastern flank of Lut Block which first time are studied by Stocklin et al.in 1972. Gorgij (2001 stratigraphically and paleontologically investigate Upper Cretaceous deposits in Mighan and Basiran sections. Upper Cretaceous deposits in in this area consists of 275m conglomerate,alternation of conglomerate-sandstone, sandy limestone -marl and limy marl, marl with intercalation of limestone-sandy limestone thin beds and medium-bedded to massive limestone. Microfacies analysis led to the recognition of 9 microfacies that are related to 5 belts; Coast, tidal flat, lagoon, shoal, shallow open marine and deep open marine environments. Main part of the section are deposited in the open marine environment that consist of marl,marly limestone and limestone. The doals of this study are : (1 describing and determining main carbonate and siliciclastic microfacies of late Cretaceous deposits (2 interpreting and providing depositional model for reconstruction of its paleoenvironmental setting based on microfacies characteristics (3 dividing the section based on lithostratigraphic principles and (4 recognizing a sequence stratigraphic model of this successions based on the vertical variation of facies,stratal key beds and stratal packing pattern.       Material and Method   The Basiran section as a complete stratigraphic section was measured and described. Up to 68 samples (indicated by KB1 to KB68 were collected and 170 thin sections are prepared. Based on field observations, sedimentological characteristics, parasequence stacking patterns, sequence boundary types and other key stratigraphical surfaces are identified and were obtained. Scheme of Dunham (1962 and Embry and Klovan

Microfacies characteristics, sedimentary environments and sequence stratigraphy of Upper Cretaceous deposits in northwest of Nehbandan (Basiran section

Directory of Open Access Journals (Sweden)

Azadeh Bordbar

2015-09-01

Full Text Available   Introduction   The Basiran stratigraphic section is located about 160 km northwest of Nehbandan.The section was measured in detail at 59 06 30 N and 31 52 50 E. Nehbandan area with respect to fourfold geological subdivision of Iran is part of Central Iran that is located in the eastern flank of Lut Block which first time are studied by Stocklin et al.in 1972. Gorgij (2001 stratigraphically and paleontologically investigate Upper Cretaceous deposits in Mighan and Basiran sections. Upper Cretaceous deposits in in this area consists of 275m conglomerate,alternation of conglomerate-sandstone, sandy limestone -marl and limy marl, marl with intercalation of limestone-sandy limestone thin beds and medium-bedded to massive limestone. Microfacies analysis led to the recognition of 9 microfacies that are related to 5 belts Coast, tidal flat, lagoon, shoal, shallow open marine and deep open marine environments. Main part of the section are deposited in the open marine environment that consist of marl,marly limestone and limestone. The doals of this study are : (1 describing and determining main carbonate and siliciclastic microfacies of late Cretaceous deposits (2 interpreting and providing depositional model for reconstruction of its paleoenvironmental setting based on microfacies characteristics (3 dividing the section based on lithostratigraphic principles and (4 recognizing a sequence stratigraphic model of this successions based on the vertical variation of facies,stratal key beds and stratal packing pattern.       Material and Method   The Basiran section as a complete stratigraphic section was measured and described. Up to 68 samples (indicated by KB1 to KB68 were collected and 170 thin sections are prepared. Based on field observations, sedimentological characteristics, parasequence stacking patterns, sequence boundary types and other key stratigraphical surfaces are identified and were obtained. Scheme of Dunham (1962 and Embry

Effect on the K/sub m/ for radiosensitization at 00C of thiol depletion by diethylmaleate pretreatment: quantitative differences found using the radiation sensitizing agent misonidazole or oxygen

International Nuclear Information System (INIS)

Koch, C.J.; Stobbe, C.C.; Bump, E.A.

1984-01-01

Pretreatment of V79-WNRE cells with 150 μM diethylmaleate for 1 hr at 37 0 C caused a decrease in intracellular glutathione levels to approximately 10-15% of control levels. The cells could be washed free of diethylmaleate and held at 0 0 C for several hours without toxicity and with no increase in glutathione concentration, although the glutathione concentration rapidly increased to normal levels at higher temperatures. Glutathione depletion itself caused a small but consistent radiosensitization of hypoxic cells (dose enhancement ratio of 1.2). However glutathione depletion caused a profound change in the radiosensitizing efficiency of misonidazole, with a decrease in K/sub m/ of about sevenfold from 0.6 to 0.09 mM. In contrast, only a 2.5-fold decrease was found in the K/sub m/ for radiosensitization by oxygen with diethylmaleate pretreatment. These results suggest a fundamental problem with the conventional theory of radiosensitivity whereby one considers a first-order competition for reaction with target radicals between radical-fixing versus radical-repairing species. It also suggests difficulties in the interpretation of glutathione as the only endogenous protective species

Enhancement of aerobic biodegradation in an oxygen-limiting environment using a saponin-based microbubble suspension

International Nuclear Information System (INIS)

Choi, Yong Ju; Kim, Young-Jin; Nam, Kyoungphile

2009-01-01

This study investigated the ability of a saponin-based microbubble suspension to enhance aerobic biodegradation of phenanthrene by subsurface delivery. As the microbubble suspension flowed through a sand column pressure buildup and release was repeatedly observed, which delivered oxygen to the less permeable regions. Burkholderia cepacia RPH1, a phenanthrene-degrading bacterium, was mainly transported in a suspended form in the microbubble suspension. When three pore volumes of the microbubble suspension containing B. cepacia RPH1 was introduced into a column contaminated with phenanthrene (100 mg/kg), the oxygen content declined to 5% from an initial value of 20% within 5 days and correspondingly, 34.4% of initial phenanthrene was removed in 8 days. The addition of two further three pore volumes enhanced the biodegradation efficiency by a factor of 2.2. Our data suggest that a saponin-based microbubble suspension could be a potential carrier for enhancing the aerobic biodegradation under an oxygen-limiting environment. - Microbubble suspension can enhance the phenanthrene biodegradation under an oxygen-limiting condition.

Enhancement of aerobic biodegradation in an oxygen-limiting environment using a saponin-based microbubble suspension

Energy Technology Data Exchange (ETDEWEB)

Choi, Yong Ju; Kim, Young-Jin [Department of Civil and Environmental Engineering, Seoul National University, Shillim-dong, Gwanak-gu, Seoul (Korea, Republic of); Nam, Kyoungphile, E-mail: kpnam@snu.ac.k [Department of Civil and Environmental Engineering, Seoul National University, Shillim-dong, Gwanak-gu, Seoul (Korea, Republic of)

2009-08-15

This study investigated the ability of a saponin-based microbubble suspension to enhance aerobic biodegradation of phenanthrene by subsurface delivery. As the microbubble suspension flowed through a sand column pressure buildup and release was repeatedly observed, which delivered oxygen to the less permeable regions. Burkholderia cepacia RPH1, a phenanthrene-degrading bacterium, was mainly transported in a suspended form in the microbubble suspension. When three pore volumes of the microbubble suspension containing B. cepacia RPH1 was introduced into a column contaminated with phenanthrene (100 mg/kg), the oxygen content declined to 5% from an initial value of 20% within 5 days and correspondingly, 34.4% of initial phenanthrene was removed in 8 days. The addition of two further three pore volumes enhanced the biodegradation efficiency by a factor of 2.2. Our data suggest that a saponin-based microbubble suspension could be a potential carrier for enhancing the aerobic biodegradation under an oxygen-limiting environment. - Microbubble suspension can enhance the phenanthrene biodegradation under an oxygen-limiting condition.

An analytical model for particulate deposition on vertical heat transfer surfaces in a boiling environment

International Nuclear Information System (INIS)

Keefer, R.H.; Rider, J.L.; Waldman, L.A.

1993-01-01

A frequent problem in heat exchange equipment is the deposition of particulates entrained in the working fluid onto heat transfer surfaces. These deposits increase the overall heat transfer resistance and can significantly degrade the performance of the heat exchanger. Accurate prediction of the deposition rate is necessary to ensure that the design and specified operating conditions of the heat exchanger adequately address the effects of this deposit layer. Although the deposition process has been studied in considerable detail, much of the work has focused on investigating individual aspects of the deposition process. This paper consolidates this previous research into a mechanistically based analytical prediction model for particulate deposition from a boiling liquid onto vertical heat transfer surfaces. Consistent with the well known Kern-Seaton approach, the model postulates net particulate accumulation to depend on the relative contributions of deposition and reentrainment processes. Mechanisms for deposition include boiling, momentum, and diffusion effects. Reentrainment is presumed to occur via an intermittent erosion process, with the energy for particle removal being supplied by turbulent flow instabilities. The contributions of these individual mechanisms are integrated to obtain a single equation for the deposit thickness versus time. The validity of the resulting model is demonstrated by comparison with data published in the open literature. Model estimates show good agreement with data obtained over a range of thermal-hydraulic conditions in both flow and pool boiling environments. The utility of the model in performing parametric studies (e.g. to determine the effect of flow velocity on net deposition) is also demonstrated. The initial success of the model suggests that it could prove useful in establishing a range of heat exchanger. operating conditions to minimize deposition

Mercury fluxes over an Australian alpine grassland and observation of nocturnal atmospheric mercury depletion events

Directory of Open Access Journals (Sweden)

D. Howard

2018-01-01

Full Text Available Aerodynamic gradient measurements of the air–surface exchange of gaseous elemental mercury (GEM were undertaken over a 40 ha alpine grassland in Australia's Snowy Mountains region across a 3-week period during the late austral summer. Bi-directional GEM fluxes were observed throughout the study, with overall mean value of 0.2 ± 14.5 ng m−2 h−1 and mean nocturnal fluxes of −1.5 ± 7.8 ng m−2 h−1 compared to diurnal fluxes of 1.8 ± 18.6 ng m−2 h−1. Deposition velocities ranged from −2.2 to 2.9 cm s−1, whilst ambient GEM concentrations throughout the study were 0.59 ± 0.10 ng m−3. Cumulative GEM fluxes correlated well with 24 h running mean soil temperatures, and one precipitation event was shown to have a positive impact on diurnal emission fluxes. The underlying vegetation had largely senesced and showed little stomatal control on fluxes. Nocturnal atmospheric mercury depletion events (NAMDEs were observed concomitant with O3 depletion and dew formation under shallow, stable nocturnal boundary layers. A mass balance box model was able to reproduce ambient GEM concentration patterns during NAMDE and non-NAMDE nights without invoking chemical oxidation of GEM throughout the column, indicating a significant role of surface processes controlling deposition in these events. Surface deposition was enhanced under NAMDE nights, though uptake to dew likely represents less than one-fifth of this enhanced deposition. Instead, enhancement of the surface GEM gradient as a result of oxidation at the surface in the presence of dew is hypothesised to be responsible for a large portion of GEM depletion during these particular events. GEM emission pulses following nights with significant deposition provide evidence for the prompt recycling of 17 % of deposited mercury, with the remaining portion retained in surface sinks. The long-term impacts of any sinks are however likely to be minimal, as

Sedimentary oxygen dynamics in a seasonally hypoxic basin

NARCIS (Netherlands)

Seitaj, D.; Sulu-Gambari, F; Burdorf, L.D.W.; Romero-Ramirez, A.; Maire, O.; Malkin, S.Y.; Slomp, C. P.; Meysman, F.J.R.

2017-01-01

Seasonal hypoxia refers to the oxygen depletion that occurs in summer in the bottom water of stratified systems, and is increasingly observed in coastal areas worldwide. The process induces a seasonal cycle on the biogeochemistry of the underlying sediments, which remains poorly quantified. Here, we

Sedimentary oxygen dynamics in a seasonally hypoxic basin

NARCIS (Netherlands)

Seitaj, Dorina; Sulu-Gambari, Fatimah; Burdorf, Laurine D. W.; Romero-Ramirez, Alicia; Maire, Olivier; Malkin, Sairah Y.; Slomp, Caroline P.; Meysman, Filip J.R.

Seasonal hypoxia refers to the oxygen depletion that occurs in summer in the bottom water of stratified systems, and is increasingly observed in coastal areas worldwide. The process induces a seasonal cycle on the biogeochemistry of the underlying sediments, which remains poorly quantified. Here, we

Computer simulations of an oxygen inductively coupled plasma used for plasma-assisted atomic layer deposition

International Nuclear Information System (INIS)

Tinck, S; Bogaerts, A

2011-01-01

In this paper, an O 2 inductively coupled plasma used for plasma enhanced atomic layer deposition of Al 2 O 3 thin films is investigated by means of modeling. This work intends to provide more information about basic plasma properties such as species densities and species fluxes to the substrate as a function of power and pressure, which might be hard to measure experimentally. For this purpose, a hybrid model developed by Kushner et al is applied to calculate the plasma characteristics in the reactor volume for different chamber pressures ranging from 1 to 10 mTorr and different coil powers ranging from 50 to 500 W. Density profiles of the various oxygen containing plasma species are reported as well as fluxes to the substrate under various operating conditions. Furthermore, different orientations of the substrate, which can be placed vertically or horizontally in the reactor, are taken into account. In addition, special attention is paid to the recombination process of atomic oxygen on the different reactor walls under the stated operating conditions. From this work it can be concluded that the plasma properties change significantly in different locations of the reactor. The plasma density near the cylindrical coil is high, while it is almost negligible in the neighborhood of the substrate. Ion and excited species fluxes to the substrate are found to be very low and negligible. Finally, the orientation of the substrate has a minor effect on the flux of O 2 , while it has a significant effect on the flux of O. In the horizontal configuration, the flux of atomic oxygen can be up to one order of magnitude lower than in the vertical configuration.

Dinitrogen fixation in aphotic oxygenated marine environments

Directory of Open Access Journals (Sweden)

Eyal eRahav

2013-08-01

Full Text Available We measured N2 fixation rates from oceanic zones that have traditionally been ignored as sources of biological N2 fixation; the aphotic, fully oxygenated, nitrate (NO3--rich, waters of the oligotrophic Levantine Basin (LB and the Gulf of Aqaba (GA. N2 fixation rates measured from pelagic aphotic waters to depths up to 720 m, during the mixed and stratified periods, ranged from 0.01 nmol N L-1 d-1 to 0.38 nmol N L-1 d-1. N2 fixation rates correlated significantly with bacterial productivity and heterotrophic diazotrophs were identified from aphotic as well as photic depths. Dissolved free amino acid amendments to whole water from the GA enhanced bacterial productivity by 2to 3.5 and N2 fixation rates by ~ 2 fold in samples collected from aphotic depths while in amendments to water from photic depths bacterial productivity increased 2 to 6 fold while N2 fixation rates increased by a factor of 2 to 4 illustrating that both BP an heterotrophic N2 fixation are carbon limited. Experimental manipulations of aphotic waters from the LB demonstrated a significant positive correlation between transparent exopolymeric particles (TEP concentration and N2 fixation rates. This suggests that sinking organic material and high carbon (C: nitrogen (N micro-environments (such as TEP-based aggregates or marine snow could support high heterotrophic N2 fixation rates in oxygenated surface waters and in the aphotic zones. Indeed, our calculations show that aphotic N2 fixation accounted for 37 to 75 % of the total daily integrated N2 fixation rates at both locations in the Mediterranean and Red Seas with rates equal or greater to those measured from the photic layers. Moreover, our results indicate that that while N2 fixation may be limited in the surface waters, aphotic, pelagic N2 fixation may contribute significantly to new N inputs in other oligotrophic basins, yet it is currently not included in regional or global N budgets.

Microcrystalline silicon deposition: Process stability and process control

International Nuclear Information System (INIS)

Donker, M.N. van den; Kilper, T.; Grunsky, D.; Rech, B.; Houben, L.; Kessels, W.M.M.; Sanden, M.C.M. van de

2007-01-01

Applying in situ process diagnostics, we identified several process drifts occurring in the parallel plate plasma deposition of microcrystalline silicon (μc-Si:H). These process drifts are powder formation (visible from diminishing dc-bias and changing spatial emission profile on a time scale of 10 0 s), transient SiH 4 depletion (visible from a decreasing SiH emission intensity on a time scale of 10 2 s), plasma heating (visible from an increasing substrate temperature on a time scale of 10 3 s) and a still puzzling long-term drift (visible from a decreasing SiH emission intensity on a time scale of 10 4 s). The effect of these drifts on the crystalline volume fraction in the deposited films is investigated by selected area electron diffraction and depth-profiled Raman spectroscopy. An example shows how the transient depletion and long-term drift can be prevented by suitable process control. Solar cells deposited using this process control show enhanced performance. Options for process control of plasma heating and powder formation are discussed

Sr{sub 2}MgMoO{sub 6−δ} thin films fabricated using pulsed-laser deposition with high concentrations of oxygen vacancies

Energy Technology Data Exchange (ETDEWEB)

Shigematsu, K. [Department of Chemistry, The University of Tokyo, Bunkyo-ku, Tokyo 113-0033 (Japan); Chikamatsu, A., E-mail: chikamatsu@chem.s.u-tokyo.ac.jp; Fukumura, T. [Department of Chemistry, The University of Tokyo, Bunkyo-ku, Tokyo 113-0033 (Japan); JST-CREST, Bunkyo-ku, Tokyo 113-0033 (Japan); Toyoda, S. [Department of Materials Science and Engineering, Kyoto University, Yoshida-honmachi, Kyoto 606-8501 (Japan); Ikenaga, E. [JASRI/SPring-8, Mikazuki-cho, Hyogo 679-5198 (Japan); Hasegawa, T. [Department of Chemistry, The University of Tokyo, Bunkyo-ku, Tokyo 113-0033 (Japan); JST-CREST, Bunkyo-ku, Tokyo 113-0033 (Japan); Kanagawa Academy of Science and Technology (KAST), Kawasaki, Kanagawa 213-0012 (Japan)

2014-06-30

We fabricated epitaxial thin films of oxygen-vacant Sr{sub 2}MgMoO{sub 6−δ} using pulsed laser deposition. The films showed low resistivity of the order of 10{sup −2} Ω cm at 300 K. X-ray diffraction analyses revealed that Mg and Mo ions in the Sr{sub 2}MgMoO{sub 6−δ} films were considerably disordered, compared to those in bulk Sr{sub 2}MgMoO{sub 6−δ}. The proportion of oxygen vacancies estimated through hard x-ray photoemission measurements was as large as 0.37, and correlated well with the Mg/Mo ordering.

Deuterium-depleted water

International Nuclear Information System (INIS)

Stefanescu, Ion; Steflea, Dumitru; Saros-Rogobete, Irina; Titescu, Gheorghe; Tamaian, Radu

2001-01-01

Deuterium-depleted water represents water that has an isotopic content smaller than 145 ppm D/(D+H) which is the natural isotopic content of water. Deuterium depleted water is produced by vacuum distillation in columns equipped with structured packing made from phosphor bronze or stainless steel. Deuterium-depleted water, the production technique and structured packing are patents of National Institute of Research - Development for Cryogenics and Isotopic Technologies at Rm. Valcea. Researches made in the last few years showed the deuterium-depleted water is a biological active product that could have many applications in medicine and agriculture. (authors)

Depletive stripping chronopotentiometry : a major step forward in electrochemical stripping techniques for metal ion speciation analysis

NARCIS (Netherlands)

Town, R.M.; Leeuwen, van H.P.

2004-01-01

A comparative evaluation of the utility of the various modes of stripping chronopotentiometry (SCP) for trace metal speciation analysis is presented in the broad context of stripping voltammetric techniques. The remarkable fundamental advantages of depletive SCP at scanned deposition potential

Controlled temperature expansion in oxygen production by molten alkali metal salts

Science.gov (United States)

Erickson, Donald C.

1985-06-04

A continuous process is set forth for the production of oxygen from an oxygen containing gas stream, such as air, by contacting a feed gas stream with a molten solution of an oxygen acceptor to oxidize the acceptor and cyclically regenerating the oxidized acceptor by releasing oxygen from the acceptor wherein the oxygen-depleted gas stream from the contact zone is treated sequentially to temperature reduction by heat exchange against the feed stream so as to condense out entrained oxygen acceptor for recycle to the process, combustion of the gas stream with fuel to elevate its temperature and expansion of the combusted high temperature gas stream in a turbine to recover power.

Geological factors of deposit formation

International Nuclear Information System (INIS)

Grushevoj, G.V.

1980-01-01

Geologic factors of hydrogenic uranium deposit formation are considered. Structural, formation and lithological-facies factors of deposit formation, connected with zones of stratal oxidation, are characterized. Peculiarities of deposit localization, connected with orogenic structures of Mesozoic and lenozoic age, are described. It is noted that deposits of anagenous group are widely spread in Paleozoic formations, infiltration uranium deposits are localized mainly in Cenozoic sediments, while uranium mineralization both anagenous and infiltration groups are widely developed in Mesozoic sediments. Anagenous deposits were formed in non-oxygen situation, their age varies from 200 to 55 mln years. Infiltration deposit formation is determined by asymmetric oxidation zonation, their age varies from 10 - 40 mln years to dozens of thousand years [ru

nTiO{sub 2} mass transfer and deposition behavior in an aquatic environment

Energy Technology Data Exchange (ETDEWEB)

Wei, Xiuzhen, E-mail: xzwei@zjut.edu.cn; He, Junhui; Wang, Meng; Fang, Jinfeng; Chen, Jinyuan, E-mail: cjy1128@zjut.edu.cn; Lv, Bosheng, E-mail: zjhzlbs@zjut.edu.cn [Zhejiang University of Technology, College of Environment (China)

2016-12-15

Nano-TiO{sub 2} (nTiO{sub 2}) is widely used in industry, and some of it is inevitably released into natural aquatic environments. nTiO{sub 2} can be deposited on the streambed or transported along the stream and streambed, and it can also undergo exchange-transfer processes in these systems. The behavior of nTiO{sub 2} in rivers includes deposition-transfer processes in the stream and exchange-transfer processes between the stream and streambed. In this work, the deposition, mass transfer, exchange, and aggregation behavior of nTiO{sub 2} in a simulated river were studied as a function of the solution pH, stream velocity, and anionic, cationic, and neutral surfactant concentrations. In these experiments, a recirculating flume was used to simulate a natural stream. The nTiO{sub 2} deposition and aggregation phenomena in the river and streambed were characterized. Of the three surfactants studied, the anionic surfactant enhanced the nTiO{sub 2} stability in the river and limited its aggregation most effectively, resulting in slow nTiO{sub 2} deposition and nTiO{sub 2} transport over long distances. This study provides information about nanoparticle transport phenomena in simulated natural aquatic systems.

Mobility Optimization in LaxBa1-xSnO3 Thin Films Deposited via High Pressure Oxygen Sputtering

Science.gov (United States)

Postiglione, William Michael

BaSnO3 (BSO) is one of the most promising semiconducting oxides currently being explored for use in future electronic applications. BSO possesses a unique combination of high room temperature mobility (even at very high carrier concentrations, > 1019 cm-3), wide band gap, and high temperature stability, making it a potentially useful material for myriad applications. Significant challenges remain however in optimizing the properties and processing of epitaxial BSO, a critical step towards industrial applications. In this study we investigate the viability of using high pressure oxygen sputtering to produce high mobility La-doped BSO thin films. In the first part of our investigation we synthesized, using solid state reaction, phase-pure stoichiometric polycrystalline 2% La-doped BaSnO 3 for use as a target material in our sputtering system. We verified the experimental bulk lattice constant, 4.117 A, to be in good agreement with literature values. Next, we set out to optimize the growth conditions for DC sputtering of La doped BaSnO3. We found that mobility for all our films increased monotonically with deposition temperature, suggesting the optimum temperature for deposition is > 900 °C and implicating a likely improvement in transport properties with post-growth thermal anneal. We then preformed systematic studies aimed at probing the effects of varying thickness and deposition rate to optimize the structural and electronic transport properties in unbuffered BSO films. In this report we demonstrate the ability to grow 2% La BSO thin films with an effective dopant activation of essentially 100%. Our films showed fully relaxed (bulk), out-of-plane lattice parameter values when deposited on LaAlO3, MgO, and (LaAlO3)0.3(Sr2 TaAlO6)0.7 substrates, and slightly expanded out-of-plane lattice parameters for films deposited on SrTiO3, GdScO3, and PrScO3 substrates. The surface roughness's of our films were measured via AFM, and determined to be on the nm scale or better

Risks associated to the depleted uranium in the piercing shells

International Nuclear Information System (INIS)

2001-01-01

Following the complaints lodged by military personnel against the consequences of the utilization of depleted uranium in weapons during the Balkans war (1995-1999), the governments of six concerned countries asked information to the NATO. In this paper the IPSN gives its own opinion on this problem: the characteristics of the uranium and the depleted uranium, the impacts of the shell fires on the human and the environment. To establish the risks in terms of leukemia and the liabilities the IPSN advises more biological tests and more information on the shells utilization. (A.L.B.)

Ego depletion in visual perception: Ego-depleted viewers experience less ambiguous figure reversal.

Science.gov (United States)

Wimmer, Marina C; Stirk, Steven; Hancock, Peter J B

2017-10-01

This study examined the effects of ego depletion on ambiguous figure perception. Adults (N = 315) received an ego depletion task and were subsequently tested on their inhibitory control abilities that were indexed by the Stroop task (Experiment 1) and their ability to perceive both interpretations of ambiguous figures that was indexed by reversal (Experiment 2). Ego depletion had a very small effect on reducing inhibitory control (Cohen's d = .15) (Experiment 1). Ego-depleted participants had a tendency to take longer to respond in Stroop trials. In Experiment 2, ego depletion had small to medium effects on the experience of reversal. Ego-depleted viewers tended to take longer to reverse ambiguous figures (duration to first reversal) when naïve of the ambiguity and experienced less reversal both when naïve and informed of the ambiguity. Together, findings suggest that ego depletion has small effects on inhibitory control and small to medium effects on bottom-up and top-down perceptual processes. The depletion of cognitive resources can reduce our visual perceptual experience.

High-affinity hemoglobin and blood oxygen saturation in diving emperor penguins.

Science.gov (United States)

Meir, Jessica U; Ponganis, Paul J

2009-10-01

The emperor penguin (Aptenodytes forsteri) thrives in the Antarctic underwater environment, diving to depths greater than 500 m and for durations longer than 23 min. To examine mechanisms underlying the exceptional diving ability of this species and further describe blood oxygen (O2) transport and depletion while diving, we characterized the O2-hemoglobin (Hb) dissociation curve of the emperor penguin in whole blood. This allowed us to (1) investigate the biochemical adaptation of Hb in this species, and (2) address blood O2 depletion during diving, by applying the dissociation curve to previously collected partial pressure of O2 (PO2) profiles to estimate in vivo Hb saturation (SO2) changes during dives. This investigation revealed enhanced Hb-O2 affinity (P50=28 mmHg, pH 7.5) in the emperor penguin, similar to high-altitude birds and other penguin species. This allows for increased O2 at low blood PO2 levels during diving and more complete depletion of the respiratory O2 store. SO2 profiles during diving demonstrated that arterial SO2 levels are maintained near 100% throughout much of the dive, not decreasing significantly until the final ascent phase. End-of-dive venous SO2 values were widely distributed and optimization of the venous blood O2 store resulted from arterialization and near complete depletion of venous blood O2 during longer dives. The estimated contribution of the blood O2 store to diving metabolic rate was low and highly variable. This pattern is due, in part, to the influx of O2 from the lungs into the blood during diving, and variable rates of tissue O2 uptake.

Excellent Silicon Surface Passivation Achieved by Industrial Inductively Coupled Plasma Deposited Hydrogenated Intrinsic Amorphous Silicon Suboxide

Directory of Open Access Journals (Sweden)

Jia Ge

2014-01-01

Full Text Available We present an alternative method of depositing a high-quality passivation film for heterojunction silicon wafer solar cells, in this paper. The deposition of hydrogenated intrinsic amorphous silicon suboxide is accomplished by decomposing hydrogen, silane, and carbon dioxide in an industrial remote inductively coupled plasma platform. Through the investigation on CO2 partial pressure and process temperature, excellent surface passivation quality and optical properties are achieved. It is found that the hydrogen content in the film is much higher than what is commonly reported in intrinsic amorphous silicon due to oxygen incorporation. The observed slow depletion of hydrogen with increasing temperature greatly enhances its process window as well. The effective lifetime of symmetrically passivated samples under the optimal condition exceeds 4.7 ms on planar n-type Czochralski silicon wafers with a resistivity of 1 Ωcm, which is equivalent to an effective surface recombination velocity of less than 1.7 cms−1 and an implied open-circuit voltage (Voc of 741 mV. A comparison with several high quality passivation schemes for solar cells reveals that the developed inductively coupled plasma deposited films show excellent passivation quality. The excellent optical property and resistance to degradation make it an excellent substitute for industrial heterojunction silicon solar cell production.

Plasma deposited fluorinated films on porous membranes

Energy Technology Data Exchange (ETDEWEB)

Gancarz, Irena [Department of Polymer and Carbon Materials, Wrocław University of Technology, 50-370 Wrocław (Poland); Bryjak, Marek, E-mail: marek.bryjak@pwr.edu.pl [Department of Polymer and Carbon Materials, Wrocław University of Technology, 50-370 Wrocław (Poland); Kujawski, Jan; Wolska, Joanna [Department of Polymer and Carbon Materials, Wrocław University of Technology, 50-370 Wrocław (Poland); Kujawa, Joanna; Kujawski, Wojciech [Nicolaus Copernicus University, Faculty of Chemistry, 7 Gagarina St., 87-100 Torun (Poland)

2015-02-01

75 KHz plasma was used to modify track etched poly(ethylene terephthalate) membranes and deposit on them flouropolymers. Two fluorine bearing monomers were used: perflourohexane and hexafluorobenzene. The modified surfaces were analyzed by means of attenuated total reflection infra-red spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, atomic force microscopy and wettability. It was detected that hexaflourobenxene deposited to the larger extent than perflourohaxane did. The roughness of surfaces decreased when more fluoropolymer was deposited. The hydrophobic character of surface slightly disappeared during 20-days storage of hexaflourobenzene modified membrane. Perfluorohexane modified membrane did not change its character within 120 days after modification. It was expected that this phenomenon resulted from post-reactions of oxygen with radicals in polymer deposits. The obtained membranes could be used for membrane distillation of juices. - Highlights: • Plasma deposited hydrophobic layer of flouropolymers. • Deposition degree affects the surface properties. • Hydrohilization of surface due to reaction of oxygen with entrapped radicals. • Possibility to use modified porous membrane for water distillation and apple juice concentration.

Declining acidic deposition begins reversal of forest-soil acidification in the northeastern U.S

Science.gov (United States)

Gregory B. Lawrence; Paul W. Hazlett; Ivan J. Fernandez; Rock Ouimet; Scott W. Bailey; Walter C. Shortle; Kevin T. Smith; Michael R. Antidormi

2015-01-01

Decreasing trends in acidic deposition levels over the past several decades have led to partial chemical recovery of surface waters. However, depletion of soil Ca from acidic deposition has slowed surface water recovery and led to the impairment of both aquatic and terrestrial ecosystems. Nevertheless, documentation of acidic deposition effects on soils has been...

High power RF window deposition apparatus, method, and device

Science.gov (United States)

Ives, Lawrence R.; Lucovsky, Gerald; Zeller, Daniel

2017-07-04

A process for forming a coating for an RF window which has improved secondary electron emission and reduced multipactor for high power RF waveguides is formed from a substrate with low loss tangent and desirable mechanical characteristics. The substrate has an RPAO deposition layer applied which oxygenates the surface of the substrate to remove carbon impurities, thereafter has an RPAN deposition layer applied to nitrogen activate the surface of the substrate, after which a TiN deposition layer is applied using Titanium tert-butoxide. The TiN deposition layer is capped with a final RPAN deposition layer of nitridation to reduce the bound oxygen in the TiN deposition layer. The resulting RF window has greatly improved titanium layer adhesion, reduced multipactor, and is able to withstand greater RF power levels than provided by the prior art.

“When the going gets tough, who keeps going?” Depletion sensitivity moderates the ego-depletion effect

Science.gov (United States)

Salmon, Stefanie J.; Adriaanse, Marieke A.; De Vet, Emely; Fennis, Bob M.; De Ridder, Denise T. D.

2014-01-01

Self-control relies on a limited resource that can get depleted, a phenomenon that has been labeled ego-depletion. We argue that individuals may differ in their sensitivity to depleting tasks, and that consequently some people deplete their self-control resource at a faster rate than others. In three studies, we assessed individual differences in depletion sensitivity, and demonstrate that depletion sensitivity moderates ego-depletion effects. The Depletion Sensitivity Scale (DSS) was employed to assess depletion sensitivity. Study 1 employs the DSS to demonstrate that individual differences in sensitivity to ego-depletion exist. Study 2 shows moderate correlations of depletion sensitivity with related self-control concepts, indicating that these scales measure conceptually distinct constructs. Study 3 demonstrates that depletion sensitivity moderates the ego-depletion effect. Specifically, participants who are sensitive to depletion performed worse on a second self-control task, indicating a stronger ego-depletion effect, compared to participants less sensitive to depletion. PMID:25009523

Effects of argon and oxygen flow rate on water vapor barrier properties of silicon oxide coatings deposited on polyethylene terephthalate by plasma enhanced chemical vapor deposition

International Nuclear Information System (INIS)

Kim, Sung-Ryong; Choudhury, Moinul Haque; Kim, Won-Ho; Kim, Gon-Ho

2010-01-01

Plasma polymer coatings were deposited from hexamethyldisiloxane on polyethylene terephthalate (PET) substrates while varying the operating conditions, such as the Ar and O 2 flow rates, at a fixed radio frequency power of 300 W. The water vapor transmission rate (WVTR) of the untreated PET was 54.56 g/m 2 /day and was decreased after depositing the silicon oxide (SiO x ) coatings. The minimum WVTR, 0.47 g/m 2 /day, was observed at Ar and O 2 flow rates of 4 and 20 sccm, respectively, with a coating thickness of 415.44 nm. The intensity of the peaks for the Si-O-Si bending at 800-820 cm -1 and Si-O-Si stretching at 1000-1150 cm -1 varied depending on the Ar and O 2 flow rates. The contact angle of the SiO x coated PET increased as the Ar flow rate was increased from 2 to 8 sccm at a fixed O 2 flow rate of 20 sccm. It decreased gradually as the oxygen flow rate increased from 12 to 28 sccm at a fixed Ar carrier gas flow rate. The examination by atomic force microscopy revealed a correlation of the SiO x morphology and the water vapor barrier performance with the Ar and O 2 flow rates. The roughness of the deposited coatings increased when either the O 2 or Ar flow rate was increased.

Oxygen Deficit: The Bio-energetic Pathophysiology

Directory of Open Access Journals (Sweden)

ABHAY KUMAR PANDEY

2014-09-01

Full Text Available Scarcity of oxygen in humans arises via three modes. The environment may have low oxygen to breath. There can be disease in respiratory system causing hindrance to uptake of oxygen from environment and the circulatory system may be sluggish to supply to body parts that starve for oxygen. Thirdly the chemico-cellular components of blood which carry oxygen may be lowered or defective. In reference to body cells several limiting sites and mechanisms affect the amount of oxygen delivered to them, and these are under regulatory control of several functional and metabolic systems.

Biological fractionation of oxygen and carbon isotopes by recent benthic foraminifera

International Nuclear Information System (INIS)

Woodruff, F.; Douglas, R.G.

1980-01-01

Recent deep-sea benthic foraminifera from five East Pacific Rise box core tops have been analyzed for oxygen and carbon isotopic composition. The five equatorial stations, with water depths of between 3200 and 4600 m, yielded fourteen specific and generic taxonomic groups. Of the taxa analyzed, Uvigerina spp. most closely approaches oxygen isotopic equilibrium with ambient sea water. Pyrgo spp. was next closest to isotopic equilibrium, being on the average 0.59 per thousand depleted in 18 O relative to Uvigerina spp. Oridorsalis umbonatus also has relatively high delta 18 O values. Most other taxa were depleted in 18 O by large amounts. In no taxa was the carbon in the CaCO 3 secreted in carbon isotopic equilibrium with the dissolved HCO 3 - of ambient sea water. (Auth.)

Structure and Electrical Properties of NdBa2Cu3Oy Thin Films by Laser Ablation at Low Oxygen Partial Pressure

DEFF Research Database (Denmark)

Mozhaev, Peter B.; Mozhaeva, Julia; Khoryushin, Alexey

2017-01-01

in the film can be suppressed by an increase of the deposition temperature or by a decrease of the oxygen partial pressure during deposition. The presence of Nd/Ba disorder during deposition stimulates the introduction of oxygen into the growing film. A simple model is proposed for estimation of oxygen......A deposition process for NdBa2Cu3Oy thin films by laser ablation at decreased deposition temperature was developed using substitution of oxygen with argon in the chamber during deposition. A low deposition rate is the crucial factor to obtain high-quality NBCO films. The Nd/Ba cation disorder...... contents in the film using structural parameters measured with XRD techniques. Studies of the post-deposition annealing process showed ordering of the Nd/Ba sub-lattice and intense oxygen in- and out-diffusion. The temperature of the post-deposition annealing step should be chosen low enough (∼400 °C...

Depletion of dendritic cells enhances innate anti-bacterial host defense through modulation of phagocyte homeostasis.

Directory of Open Access Journals (Sweden)

Stella E Autenrieth

2012-02-01

Full Text Available Dendritic cells (DCs as professional antigen-presenting cells play an important role in the initiation and modulation of the adaptive immune response. However, their role in the innate immune response against bacterial infections is not completely defined. Here we have analyzed the role of DCs and their impact on the innate anti-bacterial host defense in an experimental infection model of Yersinia enterocolitica (Ye. We used CD11c-diphtheria toxin (DT mice to deplete DCs prior to severe infection with Ye. DC depletion significantly increased animal survival after Ye infection. The bacterial load in the spleen of DC-depleted mice was significantly lower than that of control mice throughout the infection. DC depletion was accompanied by an increase in the serum levels of CXCL1, G-CSF, IL-1α, and CCL2 and an increase in the numbers of splenic phagocytes. Functionally, splenocytes from DC-depleted mice exhibited an increased bacterial killing capacity compared to splenocytes from control mice. Cellular studies further showed that this was due to an increased production of reactive oxygen species (ROS by neutrophils. Adoptive transfer of neutrophils from DC-depleted mice into control mice prior to Ye infection reduced the bacterial load to the level of Ye-infected DC-depleted mice, suggesting that the increased number of phagocytes with additional ROS production account for the decreased bacterial load. Furthermore, after incubation with serum from DC-depleted mice splenocytes from control mice increased their bacterial killing capacity, most likely due to enhanced ROS production by neutrophils, indicating that serum factors from DC-depleted mice account for this effect. In summary, we could show that DC depletion triggers phagocyte accumulation in the spleen and enhances their anti-bacterial killing capacity upon bacterial infection.

Challenges dealing with depleted uranium in Germany - Reuse or disposal

International Nuclear Information System (INIS)

Moeller, Kai D.

2007-01-01

During enrichment large amounts of depleted Uranium are produced. In Germany every year 2.800 tons of depleted uranium are generated. In Germany depleted uranium is not classified as radioactive waste but a resource for further enrichment. Therefore since 1996 depleted Uranium is sent to ROSATOM in Russia. However it still has to be dealt with the second generation of depleted Uranium. To evaluate the alternative actions in case a solution has to be found in Germany, several studies have been initiated by the Federal Ministry of the Environment. The work that has been carried out evaluated various possibilities to deal with depleted uranium. The international studies on this field and the situation in Germany have been analyzed. In case no further enrichment is planned the depleted uranium has to be stored. In the enrichment process UF 6 is generated. It is an international consensus that for storage it should be converted to U 3 O 8 . The necessary technique is well established. If the depleted Uranium would have to be characterized as radioactive waste, a final disposal would become necessary. For the planned Konrad repository - a repository for non heat generating radioactive waste - the amount of Uranium is limited by the licensing authority. The existing license would not allow the final disposal of large amounts of depleted Uranium in the Konrad repository. The potential effect on the safety case has not been roughly analyzed. As a result it may be necessary to think about alternatives. Several possibilities for the use of depleted uranium in the industry have been identified. Studies indicate that the properties of Uranium would make it useful in some industrial fields. Nevertheless many practical and legal questions are open. One further option may be the use as shielding e.g. in casks for transport or disposal. Possible techniques for using depleted Uranium as shielding are the use of the metallic Uranium as well as the inclusion in concrete. Another

Dissolved oxygen mapping: A powerful tool for site assessments and ground water monitoring

International Nuclear Information System (INIS)

Newman, W.A.; Kimball, G.

1992-01-01

Dissolved oxygen concentration profiles often provide an excellent indication of the natural biological activity of microorganisms in ground water. The analysis of dissolved oxygen in ground water also provides a rapid, inexpensive method for determining the areal extent of contaminant plumes containing aerobically degraded compounds such as petroleum hydrocarbons. Indigenous hydrocarbon degrading organisms are present at most petroleum product spills giving this technique an almost universal application for dissolved hydrocarbons in ground water. Data from several sites will be presented to demonstrate the relationship between oxygen and dissolved contaminant concentrations. The inverse relationship between oxygen concentrations and dissolved contaminants can be used in many ways. During the initial site assessment, rapid on-site testing of ground water can provide real time data to direct drilling by identification of potentially contaminated locations. Several analytical techniques are available that allow field analysis to be performed in less than five minutes. Dissolved oxygen testing also provides an inexpensive way to monitor hydrocarbon migration without expensive gas chromatography. Often a plume of oxygen depleted ground water extends farther downgradient than the dissolved hydrocarbon plume. The depletion of oxygen in a well can provide an early warning system that detects upgradient contamination before the well is impacted by detectable levels of contaminants. Another application is the measurement of the natural degradation potential for aerobic remediation. If an aerobic in-situ remediation is used, dissolved oxygen monitoring provides an inexpensive method to monitor the progress of the remediation

Exercise on-transition uncoupling of ventilatory, gas exchange and cardiac hemodynamic kinetics accompany pulmonary oxygen stores depletion to impact exercise intolerance in human heart failure.

Science.gov (United States)

Van Iterson, E H; Smith, J R; Olson, T P

2018-03-25

In contrast to knowledge that heart failure (HF) patients demonstrate peak exercise uncoupling across ventilation, gas exchange and cardiac haemodynamics, whether this dyssynchrony follows that at the exercise on-transition is unclear. This study tested whether exercise on-transition temporal lag for ventilation relative to gas exchange and oxygen pulse (O 2 pulse) couples with effects from abnormal pulmonary gaseous oxygen store (O 2store ) contributions to V˙O 2 to interdependently precipitate persistently elevated ventilatory demand and low oxidative metabolic capacity in HF. Beat-to-beat HR and breath-to-breath ventilation and gas exchange were continuously acquired in HF (N = 9, ejection fraction = 30 ± 9%) and matched controls (N = 10) during square-wave ergometry at 60% V˙O 2peak (46 ± 14 vs 125 ± 54-W, P < .001). Temporal responses across V˙ E , V˙O 2 and O 2 pulse were assessed for the exercise on-transition using single exponential model Phase II on-kinetic time constants (τ = time to reach 63% steady-state rise). Breath-to-breath gas fractions and respiratory flows were used to determine O 2stores . HF vs controls: τ for V˙ E (137 ± 93 vs 74 ± 40-seconds, P = .03), V˙O 2 (60 ± 40 vs 23 ± 5-seconds, P = .03) and O 2 pulse (28 ± 18 vs 23 ± 15-seconds, P = .59). Within HF, τ for V˙ E differed from O 2 pulse (P < .02), but not V˙O 2 . Exercise V˙ E rise (workload indexed) differed in HF vs controls (545 ± 139 vs 309 ± 88-mL min -1 W -1 , P < .001). Exercise on-transition O 2store depletion in HF exceeded controls, generally persisting to end-exercise. These data suggest HF demonstrated exercise on-transition O 2store depletion (high O 2store contribution to V˙O 2 ) coupled with dyssynchronous V˙ E , V˙O 2 and O 2 pulse kinetics-not attributable to prolonged cardiac haemodynamics. Persistent high ventilatory demand and low oxidative metabolic capacity in HF may be precipitated by physiological uncoupling occurring within the exercise

Control of the threshold voltage by using the oxygen partial pressure in sputter-deposited InGaZnO4 thin-film transistors

International Nuclear Information System (INIS)

Ahn, Jeung Sun; Lee, Kwang Bae

2012-01-01

We investigate the controllability of the threshold voltage (V th ) by varying the O 2 partial pressure in sputter-deposited of InGaZnO 4 thin-film transistors (IGZO TFTs). We showed that the V th values could be linearly controlled from a depletion-type of V th ∼ -6 V to an enhancement-type of V th ∼ 2 V, without any abrupt change in μ sat , I on/off , and S, by only changing the O 2 partial pressure in a fixed region of the Ar partial pressure. Such V th controllability is thought to be due to the proper reduction of defect states and, in turn, to the preservation of high-performance TFT behavior.

Palynostratigraphy, palynofacies and depositional environment of a lignite-bearing succession at Surkha Mine, Cambay Basin, north-western India

Directory of Open Access Journals (Sweden)

Monga Priyanka

2015-12-01

Full Text Available The paper reports palynology and palynofacies studies of lignite-bearing sediments exposed in an opencast mine succession at Surkha, Bhavnagar District, in the coastal region of Gujarat, India. The study examined the relationships between the palynoflora, sedimentary organic matter and environment at the time of deposition of lignite and associated sediments. Based on dinoflagellate cyst biostratigraphy, the sedimentary succession is dated as early Eocene (Ypresian. Palynofacies studies helped reveal the palaeoenvironmental fluctuations. The dominance of angiosperm pollen grains, freshwater algae, microthyraceous fungi and a large share of land debris in the lower part of the succession suggests a freshwater swamp environment of deposition for the basal lignite facies. Two cenozones - Matanomadiasulcites maximus and Lakiapollis ovatus - were identified in the lower lignite facies, determined from the dominance of these pollen grains in the palynological assemblages. The presence of angiosperm pollen grains and pteridophyte spores in the carbonaceous shale horizon above the lignite facies indicates a change in the depositional regime from freshwater swamp to lagoonal. This was identified as the Arecipites wodehousei cenozone due to its numerical abundance in the assemblage. Dinoflagellate cyst abundance and diversity, and microforaminiferal test linings along with well-sorted terrestrial debris in the mudstone in the upper part of the succession suggest a more open marine estuarine type of depositional environment. The Homotryblium complex along with Cordospheridium fibrospinosum, Kenleyia sp., and Thalassiphora pelagica dinoflagellate cysts are the main representatives of this zone, determined as the Homotryblium tenuispinosum cenozone. The changing depositional settings (freshwater swamp-lagoonal-estuarine along the vertical succession indicate a marine transgression in this region. Results from palynological studies of early Palaeogene

Fate of Chloromethanes in the Atmospheric Environment: Implications for Human Health, Ozone Formation and Depletion, and Global Warming Impacts.

Science.gov (United States)

Tsai, Wen-Tien

2017-09-21

Among the halogenated hydrocarbons, chloromethanes (i.e., methyl chloride, CH₃Cl; methylene chloride, CH₂Cl₂; chloroform, CHCl₃; and carbon tetrachloride, CCl₄) play a vital role due to their extensive uses as solvents and chemical intermediates. This article aims to review their main chemical/physical properties and commercial/industrial uses, as well as the environment and health hazards posed by them and their toxic decomposition products. The environmental properties (including atmospheric lifetime, radiative efficiency, ozone depletion potential, global warming potential, photochemical ozone creation potential, and surface mixing ratio) of these chlorinated methanes are also reviewed. In addition, this paper further discusses their atmospheric fates and human health implications because they are apt to reside in the lower atmosphere when released into the environment. According to the atmospheric degradation mechanism, their toxic degradation products in the troposphere include hydrogen chloride (HCl), carbon monoxide (CO), chlorine (Cl₂), formyl chloride (HCOCl), carbonyl chloride (COCl₂), and hydrogen peroxide (H₂O₂). Among them, COCl₂ (also called phosgene) is a powerful irritating gas, which is easily hydrolyzed or thermally decomposed to form hydrogen chloride.

Evidence of coexistence of micro and nanoporosity of organo-silica polymeric films deposited on silicon by plasma deposition

International Nuclear Information System (INIS)

Purohit, Viswas; Mielczarski, Ela; Mielczarski, Jerzy A.; Akesso, Laurent

2013-01-01

A range of hybrid, SiOCH films were deposited on silicon substrates within a radio frequency plasma reactor using hexamethyldisiloxane (HMDSO) as a precursor. The plasma polymerized films were deposited at various HMDSO/argon/oxygen ratios. The composition and structure, at microscopic and nanoscopic levels, of the deposited films were determined by external reflection and transmission Fourier Transform Infrared (FTIR) spectroscopy as well as by X-Ray Photoelectron Spectroscopy (XPS). The content of carbon and oxygen in films were found to be inversely proportional to each other. XPS results showed that the outermost surface of the deposited films are nanoporous and coexist with microporosity which was revealed by electron microscopy. The structure of deposited coatings is anisotropic as was documented by polarized external reflection FTIR spectroscopy. Several correlations between the film chemical composition, surface structure, and macroscopic properties of the films such as: hydrophobicity and hydrophilicity were established. - Highlights: • Hybrid organo-polymer silicon films deposited by RF plasma on silicon substrates. • FTIR and XPS reveal porosity by interpreting bonding between Si and –O. • Quantification of nano and microporosity are identified with bonding of Si with –O

Evidence of coexistence of micro and nanoporosity of organo-silica polymeric films deposited on silicon by plasma deposition

Energy Technology Data Exchange (ETDEWEB)

Purohit, Viswas, E-mail: vishwas.purohit@gmail.com [Laboratoire Environnment et Mineralurgie, UMR 7569 CNRS, INPL-ENSG, BP.40, 54501 Vandoeuvre-les-Nancy (France); Mielczarski, Ela; Mielczarski, Jerzy A. [Laboratoire Environnment et Mineralurgie, UMR 7569 CNRS, INPL-ENSG, BP.40, 54501 Vandoeuvre-les-Nancy (France); Akesso, Laurent [Teer Coatings Ltd., Droitwich, Worcestershire WR9 9AS (United Kingdom)

2013-09-16

A range of hybrid, SiOCH films were deposited on silicon substrates within a radio frequency plasma reactor using hexamethyldisiloxane (HMDSO) as a precursor. The plasma polymerized films were deposited at various HMDSO/argon/oxygen ratios. The composition and structure, at microscopic and nanoscopic levels, of the deposited films were determined by external reflection and transmission Fourier Transform Infrared (FTIR) spectroscopy as well as by X-Ray Photoelectron Spectroscopy (XPS). The content of carbon and oxygen in films were found to be inversely proportional to each other. XPS results showed that the outermost surface of the deposited films are nanoporous and coexist with microporosity which was revealed by electron microscopy. The structure of deposited coatings is anisotropic as was documented by polarized external reflection FTIR spectroscopy. Several correlations between the film chemical composition, surface structure, and macroscopic properties of the films such as: hydrophobicity and hydrophilicity were established. - Highlights: • Hybrid organo-polymer silicon films deposited by RF plasma on silicon substrates. • FTIR and XPS reveal porosity by interpreting bonding between Si and –O. • Quantification of nano and microporosity are identified with bonding of Si with –O.

Impact and mitigation of stratospheric ozone depletion by chemical rockets

International Nuclear Information System (INIS)

Mcdonald, A.J.

1992-03-01

The American Institute of Aeronautics and Astronautics (AIAA) conducted a workshop in conjunction with the 1991 AIAA Joint Propulsion Conference in Sacramento, California, to assess the impact of chemical rocket propulsion on the environment. The workshop included recognized experts from the fields of atmospheric physics and chemistry, solid rocket propulsion, liquid rocket propulsion, government, and environmental agencies, and representatives from several responsible environmental organizations. The conclusion from this workshop relative to stratospheric ozone depletion was that neither solid nor liquid rocket launchers have a significant impact on stratospheric ozone depletion, and that there is no real significant difference between the two

Effect of low oxygen concentrations on growth and alpha-amylase production of Aspergillus oryzae in model solid-state fermentation systems

NARCIS (Netherlands)

Rahardjo, Y.S.P.; Sie, S.; Weber, F.J.; Tramper, J.; Rinzema, A.

2005-01-01

Oxygen transfer in the fungal mat is a major concern in solid-state fermentation (SSF). Oxygen supply into the mycelial layers is hampered by diffusion limitation. For aerobic fungi, like Aspergillus oryzae, this oxygen depletion can be a severely limiting factor for growth and metabolite

Effects of post-deposition oxygen annealing on tuning properties of Ba0.8Sr0.2TiO3 thin-film capacitors for microwave integrated circuits

International Nuclear Information System (INIS)

Liu, Y.R.; Lai, P.T.; Li, G.Q.; Li, B.; Peng, J.B.; Lo, H.B.

2005-01-01

Barium strontium titanate (BST) thin-films deposited on a SiO 2 /Si substrate by argon ion-beam sputtering technique were annealed at 400, 500 and 600 deg. C in oxygen for 30 min, respectively, and were used to fabricate integrated parallel-plate capacitors by standard integrated-circuit technology. These capacitors can achieve tunability greater than 60% at an applied dc voltage of 2 V and a frequency of 100 kHz at room temperature. Considering tunability, loss factor and hysteresis effect, the BST thin-film annealed at 500 deg. C is superior for making tunable microwave integrated capacitors. The effects of annealing treatment in oxygen on the tuning properties of the thin-film capacitors are analyzed, and the results indicate that the tunability is strongly dependent on both oxygen vacancies and negatively charged oxygen, trapped at the grain boundary and/or at the electrode/dielectric interface

Transparent conductive p-type lithium-doped nickel oxide thin films deposited by pulsed plasma deposition

Science.gov (United States)

Huang, Yanwei; Zhang, Qun; Xi, Junhua; Ji, Zhenguo

2012-07-01

Transparent p-type Li0.25Ni0.75O conductive thin films were prepared on conventional glass substrates by pulsed plasma deposition. The effects of substrate temperature and oxygen pressure on structural, electrical and optical properties of the films were investigated. The electrical resistivity decreases initially and increases subsequently as the substrate temperature increases. As the oxygen pressure increases, the electrical resistivity decreases monotonically. The possible physical mechanism was discussed. And a hetero p-n junction of p-Li0.25Ni0.75O/n-SnO2:W was fabricated by depositing n-SnO2:W on top of the p-Li0.25Ni0.75O, which exhibits typical rectifying current-voltage characteristics.

Transparent conductive p-type lithium-doped nickel oxide thin films deposited by pulsed plasma deposition

International Nuclear Information System (INIS)

Huang Yanwei; Zhang Qun; Xi Junhua; Ji Zhenguo

2012-01-01

Transparent p-type Li 0.25 Ni 0.75 O conductive thin films were prepared on conventional glass substrates by pulsed plasma deposition. The effects of substrate temperature and oxygen pressure on structural, electrical and optical properties of the films were investigated. The electrical resistivity decreases initially and increases subsequently as the substrate temperature increases. As the oxygen pressure increases, the electrical resistivity decreases monotonically. The possible physical mechanism was discussed. And a hetero p-n junction of p-Li 0.25 Ni 0.75 O/n-SnO 2 :W was fabricated by depositing n-SnO 2 :W on top of the p-Li 0.25 Ni 0.75 O, which exhibits typical rectifying current-voltage characteristics.

An Atmospheric Atomic Oxygen Source for Cleaning Smoke Damaged Art Objects

Science.gov (United States)

Banks, Bruce A.; Rutledge, Sharon K.; Norris, Mary Jo

1998-01-01

Soot and other carbonaceous combustion products deposited on the surfaces of porous ceramic, stone, ivory and paper can be difficult to remove and can have potentially unsatisfactory results using wet chemical and/or abrasive cleaning techniques. An atomic oxygen source which operates in air at atmospheric pressure, using a mixture of oxygen and helium, has been developed to produce an atomic oxygen beam which is highly effective in oxidizing soot deposited on surfaces by burning candles made of paraffin, oil or rendered animal fat. Atomic oxygen source operating conditions and the results of cleaning soot from paper, gesso, ivory, limestone and water color-painted limestone are presented,

Silibinin activates AMP-activated protein kinase to protect neuronal cells from oxygen and glucose deprivation-re-oxygenation.

Science.gov (United States)

Xie, Zhi; Ding, Sheng-quan; Shen, Ya-fang

2014-11-14

In this study, we explored the cytoprotective potential of silibinin against oxygen-glucose deprivation (OGD)-induced neuronal cell damages, and studied underling mechanisms. In vitro model of ischemic stroke was created by keeping neuronal cells (SH-SY5Y cells and primary mouse cortical neurons) in an OGD condition followed by re-oxygenation. Pre-treatment of silibinin significantly inhibited OGD/re-oxygenation-induced necrosis and apoptosis of neuronal cells. OGD/re-oxygenation-induced reactive oxygen species (ROS) production and mitochondrial membrane potential (MMP) reduction were also inhibited by silibinin. At the molecular level, silibinin treatment in SH-SY5Y cells and primary cortical neurons led to significant AMP-activated protein kinase (AMPK) signaling activation, detected by phosphorylations of AMPKα1, its upstream kinase liver kinase B1 (LKB1) and the downstream target acetyl-CoA Carboxylase (ACC). Pharmacological inhibition or genetic depletion of AMPK alleviated the neuroprotective ability of silibinin against OGD/re-oxygenation. Further, ROS scavenging ability by silibinin was abolished with AMPK inhibition or silencing. While A-769662, the AMPK activator, mimicked silibinin actions and suppressed ROS production and neuronal cell death following OGD/re-oxygenation. Together, these results show that silibinin-mediated neuroprotection requires activation of AMPK signaling. Copyright © 2014 Elsevier Inc. All rights reserved.

Comparison of lanthanum substituted bismuth titanate (BLT) thin films deposited by sputtering and pulsed laser deposition

International Nuclear Information System (INIS)

Besland, M.P.; Djani-ait Aissa, H.; Barroy, P.R.J.; Lafane, S.; Tessier, P.Y.; Angleraud, B.; Richard-Plouet, M.; Brohan, L.; Djouadi, M.A.

2006-01-01

Bi 4-x La x Ti 3 O 12 (BLT x ) (x = 0 to 1) thin films were grown on silicon (100) and platinized substrates Pt/TiO 2 /SiO 2 /Si using RF diode sputtering, magnetron sputtering and pulsed laser deposition (PLD). Stoichiometric home-synthesized targets were used. Reactive sputtering was investigated in argon/oxygen gas mixture, with a pressure ranging from 0.33 to 10 Pa without heating the substrate. PLD was investigated in pure oxygen, at a chamber pressure of 20 Pa for a substrate temperature of 400-440 deg. C. Comparative structural, chemical, optical and morphological characterizations of BLT thin films have been performed by X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS), X-Ray Photoelectron Spectroscopy (XPS), Spectro-ellipsometric measurements (SE) and Atomic Force Microscopy (AFM). Both sputtering techniques allow to obtain uniform films with thickness ranging from 200 to 1000 nm and chemical composition varying from (Bi,La) 2 Ti 3 O 12 to (Bi,La) 4.5 Ti 3 O 12 , depending on deposition pressure and RF power. In addition, BLT films deposited by magnetron sputtering, at a pressure deposition ranging from 1.1 to 5 Pa, were well-crystallized after a post-deposition annealing at 650 deg. C in oxygen. They exhibit a refractive index and optical band gap of 2.7 and 3.15 eV, respectively. Regarding PLD, single phase and well-crystallized, 100-200 nm thick BLT films with a stoichiometric (Bi,La) 4 Ti 3 O 12 chemical composition were obtained, exhibiting in addition a preferential orientation along (200). It is worth noting that BLT films deposited by magnetron sputtering are as well-crystallized than PLD ones

Nematode community structure along a central Chile margin transect influenced by the oxygen minimum zone

Science.gov (United States)

Neira, Carlos; King, Ian; Mendoza, Guillermo; Sellanes, Javier; De Ley, Paul; Levin, Lisa A.

2013-08-01

Nematodes are among the metazoans most tolerant of low-oxygen conditions and play major roles in seafloor ecosystem processes. Nematode communities were studied in sediments off Concepción, Central Chile, spanning the outer shelf within the OMZ (122 m) to the mid-lower continental slope (972 m) beneath the OMZ. The total density and biomass of nematodes (core depth 0-10 cm) ranged from 677 to 2006 ind. 10 cm-2, and 168.4 to 506.5 μg DW 10 cm-2, respectively. Among metazoan meiofaunal taxa, nematodes predominated at all sites both in terms of relative abundance (83.7-99.4%) and biomass (53.8-88.1%), followed by copepods, nauplii and polychaetes. Nematodes were represented by 33 genera distributed among 17 families, with densities greatest at low oxygen sites (122-364 m; ~2000 ind. 10 cm-2). Nematode generic and trophic diversity, and individual biomass were lowest, and Rank 1 dominance was highest, at the most oxygen-depleted site (122 m), despite the fact that the organic carbon content of the sediment was maximal at this depth. At the most oxygenated slope sites (827 and 972 m), all of Wieser's nematode feeding groups were represented. In contrast, at the lowest-oxygen site, only selective deposit (bacterial) feeders (1A) were present, indicating a reduction in trophic complexity. A large percentage of nematodes inhabited subsurface sediment layers (>1 cm). At deeper, more oxygenated sites (827 and 972 m), nematode individual biomass increased downcore, while within the OMZ, nematode biomass was low and remained relatively uniform through the sediment column. The concentration of nematodes in deeper sediment layers, the vertical distribution of the feeding groups, as well as the high nutritional quality of the deeper layers, suggest a differential resource partitioning of the food available, which may reduce interspecific competition.

Effect of Ground Surface Roughness on Atmospheric Dispersion and Dry Deposition of Cs-137 in the UAE Environment

Energy Technology Data Exchange (ETDEWEB)

Kim, Sungyeop; Beeley, Philip A. [Khalifa Univ. of Science, Abu Dhabi (United Arab Emirates); Kim, Sungyeop; Chang, Soonheung; Lee, Kunjai [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

2013-05-15

The site of nuclear power plant (NPP) in the UAE has several unique characteristics as a NPP on the desert environment near coastal region. Those characteristics are represented like below: · Arid ground surface · Low ground surface roughness length · Relatively simple (flat) terrain · Extremely low precipitation · Intense solar radiation and high temperature in day time · Sea breeze · Relatively high humidity of atmosphere · Etc. From the review of this desert environment in the UAE, low ground surface roughness is regarded as one of definitively different characteristics from that of other NPP sites. In this context, surface roughness is selected as independent variables for the sensitivity analyses in this research. Another important reason of this selection is that this parameters is less dependent on the day and night change than other parameters. With ground level concentration, dry deposition rate has been chosen as a dependent variable to be considered rather than wet deposition because UAE shows almost zero rainfall especially in summer. Lower ground level concentration of Cs-137 near the site and extremely lower dry deposition of Cs-137 are predicted in the UAE environment because of the lower ground surface roughness of the desert.

Thermodynamics and Kinetics of Sulfide Oxidation by Oxygen: A Look at Inorganically Controlled Reactions and Biologically Mediated Processes in the Environment

Science.gov (United States)

Luther, George W.; Findlay, Alyssa J.; MacDonald, Daniel J.; Owings, Shannon M.; Hanson, Thomas E.; Beinart, Roxanne A.; Girguis, Peter R.

2011-01-01

The thermodynamics for the first electron transfer step for sulfide and oxygen indicates that the reaction is unfavorable as unstable superoxide and bisulfide radical ions would need to be produced. However, a two-electron transfer is favorable as stable S(0) and peroxide would be formed, but the partially filled orbitals in oxygen that accept electrons prevent rapid kinetics. Abiotic sulfide oxidation kinetics improve when reduced iron and/or manganese are oxidized by oxygen to form oxidized metals which in turn oxidize sulfide. Biological sulfur oxidation relies on enzymes that have evolved to overcome these kinetic constraints to affect rapid sulfide oxidation. Here we review the available thermodynamic and kinetic data for H2S and HS• as well as O2, reactive oxygen species, nitrate, nitrite, and NOx species. We also present new kinetic data for abiotic sulfide oxidation with oxygen in trace metal clean solutions that constrain abiotic rates of sulfide oxidation in metal free solution and agree with the kinetic and thermodynamic calculations. Moreover, we present experimental data that give insight on rates of chemolithotrophic and photolithotrophic sulfide oxidation in the environment. We demonstrate that both anaerobic photolithotrophic and aerobic chemolithotrophic sulfide oxidation rates are three or more orders of magnitude higher than abiotic rates suggesting that in most environments biotic sulfide oxidation rates will far exceed abiotic rates due to the thermodynamic and kinetic constraints discussed in the first section of the paper. Such data reshape our thinking about the biotic and abiotic contributions to sulfide oxidation in the environment. PMID:21833317

Characterization of Blistering and Delamination in Depleted Uranium Hohlraums

Energy Technology Data Exchange (ETDEWEB)

Biobaum, K. J. M.

2013-03-01

Blistering and delamination are the primary failure mechanisms during the processing of depleted uranium (DU) hohlraums. These hohlraums consist of a sputter-deposited DU layer sandwiched between two sputter-deposited layers of gold; a final thick gold layer is electrodeposited on the exterior. The hohlraum is deposited on a copper-coated aluminum mandrel; the Al and Cu are removed with chemical etching after the gold and DU layers are deposited. After the mandrel is removed, blistering and delamination are observed on the interiors of some hohlraums, particularly at the radius region. It is hypothesized that blisters are caused by pinholes in the copper and gold layers; etchant leaking through these holes reaches the DU layer and causes it to oxidize, resulting in a blister. Depending on the residual stress in the deposited layers, blistering can initiate larger-scale delamination at layer interfaces. Scanning electron microscopy indicates that inhomogeneities in the machined aluminum mandrel are replicated in the sputter-deposited copper layer. Furthermore, the Cu layer exhibits columnar growth with pinholes that likely allow etchant to come in contact with the gold layer. Any inhomogeneities or pinholes in this initial gold layer then become nucleation sites for blistering. Using a focused ion beam system to etch through the gold layer and extract a cross-sectional sample for transmission electron microscopy, amorphous, intermixed layers at the gold/DU interfaces are observed. Nanometer-sized bubbles in the sputtered and electrodeposited gold layers are also present. Characterization of the morphology and composition of the deposited layers is the first step in determining modifications to processing parameters, with the goal of attaining a significant improvement in hohlraum yield.

Resistive switching effects in CeO2/La0.7(Sr0.1Ca0.9)0.3MnO3/Pt heterostructures prepared by pulse laser deposition method

International Nuclear Information System (INIS)

Chen, X.G.; Fu, J.B.; Li, L.Z.; Yun, C.; Zhao, H.; Zhang, X.F.; Wang, C.S.; Yang, Y.C.; Yang, J.B.

2014-01-01

The heterostructural junctions of CeO 2 /La 0.7 (Sr 0.1 Ca 0.9 ) 0.3 MnO 3 /Pt (CeO 2 /LSCMO/Pt) were prepared using pulse laser deposition technique. Their resistive switching (RS) behavior was investigated. As compared to the metal/manganite/Pt junction, the CeO 2 /LSCMO/Pt device displayed an improved switching characteristic. The RS effects with characteristics of bipolar, threshold, and complementary were realized by adjusting the thicknesses of the CeO 2 layer in the CeO 2 /LSCMO/Pt junctions. Under a higher external bias voltage, the threshold and complementary switching modes of the junctions could turn into bipolar switching mode. The switching behavior shows strong dependence on the O 2 partial pressure during the fabrication, indicating that the amount and behavior of the oxygen at the interface play an important role in the determination of the RS behavior. The observed switching behavior is related to the modification of the accumulation/depletion layers as well as the interfacial potential barrier due to the migration of the oxygen vacancies. - Highlights: • Heterostructure of CeO 2 /LSMO/Pt displayed an improved resistance switching characteristic. • Resistance switching with characteristics of bipolar, threshold and complementary was found. • Threshold and complementary switching mode could turn into bipolar switching mode. • Switching behavior is related to the modification of the accumulation/depletion layers. • Interfacial potential barrier due to the migration of oxygen vacancies was proposed

Depositional environment of a fan delta in a Vistulian proglacial lake (Skaliska Basin, north-eastern Poland

Directory of Open Access Journals (Sweden)

Woronko Barbara

2013-06-01

Full Text Available The study reconstructed the environment of a fan delta filling the vast end depression of the Skaliska Basin, and its overlying aeolian deposits. The formation of the large fan delta is associated with the presence of an ice-dammed lake functioning during the retreat of the Vistulian Glaciation (MIS 2. The examined material was collected from five boreholes. Sediments were analysed for their granulometric composition and subjected to analyses of frosting and rounding of quartz grains. Grain size analysis showed that the fan delta deposits are built of sand sediments of very low lateral and vertical variability. The fan delta was supplied with fluvioglacial sediments. Accumulation of sediments occurred in shallow water with a very low-gradient slope. The exposed fan delta became a site conducive to aeolian processes after the lake waters fell and the Skaliska Basin depression dried. Dune deposits overlying the fan were affected by short-distance transport so they did not acquire features typical for aeolian deposits.

Sandstone-type uranium deposits

International Nuclear Information System (INIS)

Austin, S.R.; D'Andrea, R.F. Jr.

1978-01-01

Three overall factors are necessary for formation of uranium deposits in sandstone: a source of uranium, host rocks capable of transmitting uranium-bearing solutions, and a precipitant. Possible sources of uranium in sandstone-type deposits include groundwaters emanating from granitic highlands, arkosic sediments, tuffaceous material within or overlying the host rocks, connate fluids, and overlying black shales. The first three sources are considered the most likely. Host rocks are generally immature sandstones deposited in alluvial-fan, intermontane-basin or marginal-marine environments, but uranium deposits do occur in well-winnowed barrier-bar or eolian sands. Host rocks for uranium deposits generally show coefficients of permeability on the order of 1 to 100 gal/day/ft 2 . Precipitants are normally agents capable of reducing uranium from the uranyl to the uranous state. The association of uranium with organic matter is unequivocal; H 2 S, a powerful reductant, may have been present at the time of formation of some deposits but may go unnoticed today. Vanadium can serve to preserve the tabular characteristics of some deposits in the near-surface environment, but is considered an unlikely primary precipitant for uranium. Uranium deposits in sandstone are divided into two overall types: peneconcordant deposits, which occur in locally reducing environments in otherwise oxidized sandstones; and roll-type deposits, which occur at the margin of an area where an oxidized groundwater has permeated an otherwise reduced sandstone. Uranium deposits are further broken down into four subclasses; these are described

Glutathione depletion prevents diet-induced obesity and enhances insulin sensitivity.

Science.gov (United States)

Findeisen, Hannes M; Gizard, Florence; Zhao, Yue; Qing, Hua; Jones, Karrie L; Cohn, Dianne; Heywood, Elizabeth B; Bruemmer, Dennis

2011-12-01

Excessive accumulation of reactive oxygen species (ROS) in adipose tissue has been implicated in the development of insulin resistance and type 2 diabetes. However, emerging evidence suggests a physiologic role of ROS in cellular signaling and insulin sensitivity. In this study, we demonstrate that pharmacologic depletion of the antioxidant glutathione in mice prevents diet-induced obesity, increases energy expenditure and locomotor activity, and enhances insulin sensitivity. These observations support a beneficial role of ROS in glucose homeostasis and warrant further research to define the regulation of metabolism and energy balance by ROS.

Characteristics of depositional environment and evolution of Upper Cretaceous Mishrif Formation, Halfaya Oil field, Iraq based on sedimentary microfacies analysis

Science.gov (United States)

Zhong, Yuan; Zhou, Lu; Tan, Xiucheng; Guo, Rui; Zhao, Limin; Li, Fei; Jin, Zhimin; Chen, Yantao

2018-04-01

As one of the most important carbonate targets in the Middle East, Upper Cretaceous Mishrif Formation has been highlighted for a long time. Although consensus has been reached on the overall sedimentary background, disputes still exist in understanding the sedimentary environment changes among sub-regions due to relatively limited research, rare outcrop, and incomplete drilled core, which hinders the analysis on sedimentary environment and thus the horizontal and vertical correlation. In this study, taking the Halfaya Oil Field as an example, the sedimentary microfacies analysis method was introduced to comprehensively characterize the cored interval of Mishrif Formation, including Single Layers MC1-1 to MA2. A total of 11 sedimentary microfacies are identified through system identification of sedimentary microfacies and environmental analysis, with reference to the standard microfacies classification in the rimmed carbonate platform. Then three kinds of environments are identified through microfacies assemblage analysis, namely restricted platform, open platform, and platform margin. Systematic analyses indicate that the deposits are mainly developed in the open platform and platform margin. Meanwhile, rock-electricity interpretation model is established according to the electricity response to cored intervals, and is then employed to interpret the uncored intervals, which finally helps build the sedimentary evolution pattern through horizontal and vertical correlation. It is proposed that the Single Layers MC1-1 to MB2-3 were deposited in the open platform featured by low water level, including sub-environments of low-energy shoal within platform and inter-shoal sea; Single Layers MB2-2 to MB1-2B were deposited in the open platform and platform margin, including sub-environments of high-energy shoal on the platform margin, low-energy shoal within platform, inter-shoal sea, and open sea; and Single Layers MB1-2A to MA2 were again deposited in the open platform

Proterozoic atmospheric oxygen

DEFF Research Database (Denmark)

Canfield, Donald Eugene

2014-01-01

This article is concerned with the evolution of atmospheric oxygen concentrations through the Proterozoic Eon. In particular, this article will seek to place the history of atmospheric oxygenation through the Proterozoic Eon in the context of the evolving physical environment including the history...... of continental growth and volcanic outgassing, as well as biogeochemical processing of elements within the oceans. The author will seek to explore constraints on the history of oxygenation and understand which processes have regulated oxygen through this eon....

Organic petrology, mineralogy and depositional environment of the Kipra lignite seam, Maritza-West basin, Bulgaria

Energy Technology Data Exchange (ETDEWEB)

Kostova, Irena [Department of Geology and Palaeontology, Sofia University ' ' St. Kliment Ohridski' ' , 1000, Sofia (Bulgaria); Zdravkov, Alexander [Department of Economic Geology, University of Mining and Geology ' ' St. Ivan Rilski' ' , 1700, Sofia (Bulgaria)

2007-08-01

The aim of the present study is to provide additional information about the properties and depositional environment of the Kipra lignite seam, which was deposited during the regressive stage of development of the Maritza-West basin. Petrographical and mineralogical data, along with ash yields and sulphur contents of 24 samples from a seam profile, have been used to study the vertical variation of the depositional settings during peat accumulation and subsequent coalification. The Kipra lignite is characterized by high ash yields and sulphur contents. It formed in a rheotrophic, low-lying mire with alkaline pH value. Vegetation with low preservation potential dominated within the palaeomire. During peat formation, frequent changes of the water level controlled the depositional environment. During the deposition of units 1 and 2, high water energy caused the transportation of high amounts of inorganic material into the mire, resulting in the formation of weakly gelified mineral-rich lignite. The organic matter from units 3 and 4 is characterized by enhanced gelification, which probably reflects the decreasing energy of the system. Good positive correlation between sulphur contents and the GI values was established in units 4, indicating that the gelification of the tissues was probably mainly controlled by the bacterial activity. In contrast, the gelification of the samples from unit 3 of the Kipra seam was probably governed by the redox conditions. The organic matter deposited under relatively wet conditions, in which the thermal and oxidative destruction of the tissues, was limited. A variety of major, minor and accessory minerals are present in Maritza-West lignite. The mineral composition is dominated mainly by pyrite, gypsum and calcite, and to a lesser extent limonite, quartz, kaolinite, montmorillonite, illite, chlorite and plagioclase. Jarosite, hematite, halloysite, mica, K-feldspar, aragonite, siderite, and dolomite were also determined in very low

Tectonic and sedimentological environments of sandstone-hosted uranium deposits, with special reference to the Karoo Basin of South Africa

International Nuclear Information System (INIS)

Le Roux, J.P.

1985-01-01

The principal tectonic and sedimentological settings for sandstone-hosted uranium deposits are described. Back-arc basins filled with post-Silurian, fluvial sediments bordering subduction zone magmatic arcs of calc-alkaline composition are considered favourable tectonic environments. The basins should be closed to prevent excessive oxidation of the sediments. Uranium deposits are concentrated near basin rims in the transition zone between uplift and basin subsidence, because of favourable sedimentary facies in those areas. Syn- and post-depositional deformation could have affected the localisation of uranium ore-bodies, while intrusive centres or uplifted arcs commonly have surrounding aprons of potential host rocks. Stratigraphic zoning is also related to source area tectonics and can be used to predict favourable sedimentary environments. Sedimentological processes had a direct influence on the permeability and carbonaceous matter content of sandstones and therefore have often controlled the localisation of ore-bodies. (author)

Depositional environments and sequence stratigraphy of the Bahram Formation (middle–late Devonian in north of Kerman, south-central Iran

Directory of Open Access Journals (Sweden)

Afshin Hashmie

2016-09-01

Full Text Available This study is focused on sedimentary environments, facies distribution, and sequence stratigraphy. The facies and sequence stratigraphic analyses of the Bahram Formation (middle–late Devonian in south-central Iran are based on two measured stratigraphic sections in the southern Tabas block. The Bahram Formation overlies red sandstones Padeha Formation in sections Hutk and Sardar and is overlain by Carboniferous carbonate deposits of Hutk Formation paraconformably, with a thickness of 354 and 386 m respectively. Mixed siliciclastic and carbonate sediments are present in this succession. The field observations and laboratory studies were used to identify 14 micro/petrofacies, which can be grouped into 5 depositional environments: shore, tidal flat, lagoon, shoal and shallow open marine. A mixed carbonate-detrital shallow shelf is suggested for the depositional environment of the Bahram Formation which deepens to the east (Sardar section and thins in southern locations (Hutk section. Three 3rd-order cyclic siliciclastic and carbonate sequences in the Bahram Formation and one sequence shared with the overlying joint with Hutk Formation are identified, on the basis of shallowing upward patterns in the micro/pertofacies.

Sustained Water Quality Impacts in Marine Environments Due to Mechanical Milling of Volcanic Deposits

Science.gov (United States)

Genareau, K. D.; Cronin, S. J.; Stewart, C.; Back, E.

2015-12-01

Explosive volcanic eruptions are known to be a significant geohazard, but post- or inter-eruptive processes (such as lahars, landslides, and debris avalanches) can be equally damaging to local and regional areas by remobilizing deposits. Numerous studies have found that soluble salts bound to ash grain surfaces may be quickly released into exposed waters, often lowering pH and adding trace metals with both beneficial and deleterious effects on marine flora and fauna (e.g., Fe influx initiating blooms of marine phytoplankton). Most of the cation content of pyroclastic deposits is released slowly into the environment through weathering and alteration processes. However, other pathways exist through the physical comminution of pyroclasts in fluvial and marine settings. In this case, mechanical fracturing of pyroclasts during progressive stages of disaggregation will lead to exposure of reactive particle surfaces. This study evaluates the potential, ongoing effects on water quality by experimental, mechanical milling of pyroclasts and the evaluation of released metals into exposed waters using the pyroclastic density current deposits of both the 2010 eruption of Merapi and the 2014 eruption of Kelud (Java, Indonesia), which have a bulk basaltic andesite/andesite composition (60-65 wt% SiO2). The electrical conductivity (EC) of water samples positively correlates with Ca and Sr concentrations in the case of bulk ash, whole, and crushed lapilli, but correlates with Na for the milled samples. Compared to other stages of pyroclast disaggregation, milled lapilli have the greatest effect on the concentration of alkali elements and produce a significant increase in Ca, Na, K, and Si. Mechanical milling of pyroclasts grinds down minerals and glass, resulting in an increased EC, pH, and Na concentration of exposed waters. Similar experiments are currently being conducted using basalt (50 wt% SiO2) and rhyolite (70 wt% SiO2) deposits, and these results will be presented

Laser deposition of HTSC films

International Nuclear Information System (INIS)

Sobol', Eh.N.; Bagratashvili, V.N.; Zherikhin, A.N.; Sviridov, A.P.

1990-01-01

Studies of the high-temperature superconducting (HTSC) films fabrication by the laser deposition are reviewed. Physical and chemical processes taking place during laser deposition are considered, such as the target evaporation, the material transport from the target to the substrate, the film growth on the substrate, thermochemical reactions and mass transfer within the HTSC films and their stability. The experimental results on the laser deposition of different HTSC ceramics and their properties investigations are given. The major technological issues are discussed including the deposition schemes, the oxygen supply, the target compositions and structure, the substrates and interface layers selection, the deposition regimes and their impact on the HTSC films properties. 169 refs.; 6 figs.; 2 tabs

Halo Star Lithium Depletion

International Nuclear Information System (INIS)

Pinsonneault, M. H.; Walker, T. P.; Steigman, G.; Narayanan, Vijay K.

1999-01-01

The depletion of lithium during the pre-main-sequence and main-sequence phases of stellar evolution plays a crucial role in the comparison of the predictions of big bang nucleosynthesis with the abundances observed in halo stars. Previous work has indicated a wide range of possible depletion factors, ranging from minimal in standard (nonrotating) stellar models to as much as an order of magnitude in models that include rotational mixing. Recent progress in the study of the angular momentum evolution of low-mass stars permits the construction of theoretical models capable of reproducing the angular momentum evolution of low-mass open cluster stars. The distribution of initial angular momenta can be inferred from stellar rotation data in young open clusters. In this paper we report on the application of these models to the study of lithium depletion in main-sequence halo stars. A range of initial angular momenta produces a range of lithium depletion factors on the main sequence. Using the distribution of initial conditions inferred from young open clusters leads to a well-defined halo lithium plateau with modest scatter and a small population of outliers. The mass-dependent angular momentum loss law inferred from open cluster studies produces a nearly flat plateau, unlike previous models that exhibited a downward curvature for hotter temperatures in the 7Li-Teff plane. The overall depletion factor for the plateau stars is sensitive primarily to the solar initial angular momentum used in the calibration for the mixing diffusion coefficients. Uncertainties remain in the treatment of the internal angular momentum transport in the models, and the potential impact of these uncertainties on our results is discussed. The 6Li/7Li depletion ratio is also examined. We find that the dispersion in the plateau and the 6Li/7Li depletion ratio scale with the absolute 7Li depletion in the plateau, and we use observational data to set bounds on the 7Li depletion in main-sequence halo

Isotopic investigation of the colloidal mobility of depleted uranium in a podsolic soil

International Nuclear Information System (INIS)

Harguindeguy, S.; Crancon, P.; Pointurier, F.; Potin-Gautier, M.; Lespes, G.

2014-01-01

The mobility and colloidal migration of uranium were investigated in a soil where limited amounts of anthropogenic uranium (depleted in the "2"3"5U isotope) were deposited, adding to the naturally occurring uranium. The colloidal fraction was assumed to correspond to the operational fraction between 10 kDa and 1.2 μm after (ultra)filtration. Experimental leaching tests indicate that approximately 8-15% of uranium is desorbed from the soil. Significant enrichment of the leachate in the depleted uranium (DU) content indicates that uranium from recent anthropogenic DU deposit is weakly bound to soil aggregates and more mobile than geologically occurring natural uranium (NU). Moreover, 80% of uranium in leachates was located in the colloidal fractions. Nevertheless, the percentage of DU in the colloidal and dissolved fractions suggests that NU is mainly associated with the non-mobile coarser fractions of the soil. A field investigation revealed that the calculated percentages of DU in soil and groundwater samples result in the enhanced mobility of uranium downstream from the deposit area. Colloidal uranium represents between 10% and 32% of uranium in surface water and between 68% and 90% of uranium in groundwater where physicochemical parameters are similar to those of the leachates. Finally, as observed in batch leaching tests, the colloidal fractions of groundwater contain slightly less DU than the dissolved fraction, indicating that DU is primarily associated with macromolecules in dissolved fraction. (authors)

Use of molecular oxygen to reduce EUV-induced carbon contamination of optics

Science.gov (United States)

Malinowski, Michael E.; Grunow, Philip A.; Steinhaus, Chip; Clift, W. Miles; Klebanoff, Leonard E.

2001-08-01

Carbon deposition and removal experiments on Mo/Si multilayer mirror (MLM) samples were performed using extreme ultraviolet (EUV) light on Beamline 12.0.1.2 of the Advanced Light Source, Lawrence Berkeley National Laboratory (LBNL). Carbon (C) was deposited onto Mo/Si multilayer mirror (MLM) samples when hydrocarbon vapors where intentionally introduced into the MLM test chamber in the presence of EUV at 13.44 nm (92.3eV). The carbon deposits so formed were removed by molecular oxygen + EUV. The MLM reflectivities and photoemission were measured in-situ during these carbon deposition and cleaning procedures. Auger Electron Spectroscopy (AES) sputter-through profiling of the samples was performed after experimental runs to help determine C layer thickness and the near-surface compositional-depth profiles of all samples studied. EUV powers were varied from ~0.2mW/mm2 to 3mW/mm2(at 13.44 nm) during both deposition and cleaning experiments and the oxygen pressure ranged from ~5x10-5 to 5x10-4 Torr during the cleaning experiments. C deposition rates as high as ~8nm/hr were observed, while cleaning rates as high as ~5nm/hr could be achieved when the highest oxygen pressure were used. A limited set of experiments involving intentional oxygen-only exposure of the MLM samples showed that slow oxidation of the MLM surface could occur.

Imaging Quaternary glacial deposits and basement topography using the transient electromagnetic method for modeling aquifer environments

Science.gov (United States)

Simard, Patrick Tremblay; Chesnaux, Romain; Rouleau, Alain; Daigneault, Réal; Cousineau, Pierre A.; Roy, Denis W.; Lambert, Mélanie; Poirier, Brigitte; Poignant-Molina, Léo

2015-08-01

Aquifer formations along the northern shore of the Saint-Lawrence River in Quebec (Canada) mainly consist of glacial and coastal deposits of variable thickness overlying Precambrian bedrock. These deposits are important because they provide the main water supply for many communities. As part of a continuing project aimed at developing an inventory of the groundwater resources in the Charlevoix and Haute-Côte-Nord (CHCN) regions of the province of Quebec in Canada, the central loop transient electromagnetic (TEM) method was used to map the principal hydrogeological environments in these regions. One-dimensional smooth inversion models of the TEM soundings have been used to construct two-dimensional electrical resistivity sections, which provided images for hydrogeological validation. Electrical contour lines of aquifer environments were compared against available well logs and Quaternary surface maps in order to interpret TEM soundings. A calibration table was achieved to represent common deposits and basements. The calibration table was then exported throughout the CHCN region. This paper presents three case studies; one in the Forestville site, another in the Les Escoumins site and the other in the Saint-Urbain site. These sites were selected as targets for geophysical surveys because of the general lack of local direct hydrogeological data related to them.

Phototrophs in high-iron-concentration microbial mats: physiological ecology of phototrophs in an iron-depositing hot spring

Science.gov (United States)

Pierson, B. K.; Parenteau, M. N.; Griffin, B. M.

1999-01-01

At Chocolate Pots Hot Springs in Yellowstone National Park the source waters have a pH near neutral, contain high concentrations of reduced iron, and lack sulfide. An iron formation that is associated with cyanobacterial mats is actively deposited. The uptake of [(14)C]bicarbonate was used to assess the impact of ferrous iron on photosynthesis in this environment. Photoautotrophy in some of the mats was stimulated by ferrous iron (1.0 mM). Microelectrodes were used to determine the impact of photosynthetic activity on the oxygen content and the pH in the mat and sediment microenvironments. Photosynthesis increased the oxygen concentration to 200% of air saturation levels in the top millimeter of the mats. The oxygen concentration decreased with depth and in the dark. Light-dependent increases in pH were observed. The penetration of light in the mats and in the sediments was determined. Visible radiation was rapidly attenuated in the top 2 mm of the iron-rich mats. Near-infrared radiation penetrated deeper. Iron was totally oxidized in the top few millimeters, but reduced iron was detected at greater depths. By increasing the pH and the oxygen concentration in the surface sediments, the cyanobacteria could potentially increase the rate of iron oxidation in situ. This high-iron-content hot spring provides a suitable model for studying the interactions of microbial photosynthesis and iron deposition and the role of photosynthesis in microbial iron cycling. This model may help clarify the potential role of photosynthesis in the deposition of Precambrian banded iron formations.

Reactive-environment, hollow cathode sputtering: Basic characteristics and application to Al2O3, doped ZnO, and In2O3:Mo

International Nuclear Information System (INIS)

Delahoy, A.E.; Guo, S.Y.; Paduraru, C.; Belkind, A.

2004-01-01

A method for thin-film deposition has been studied. The method is based on metal sputtering in a hollow cathode configuration with supply of a reactive gas in the vicinity of the substrate. The working gas and entrained sputtered atoms exit the cathode through an elongated slot. The reactive gas is thereby largely prevented from reaching the target. The basic operation of the cathode was studied using a Cu target and pulsed power excitation. These studies included the dependence of deposition rate on power, pressure, and flow rate, film thickness profiles, and film resistivity as a function of substrate conditions. Modeling was conducted to calculate the gas velocity distribution and pressure inside the cavity. Al 2 O 3 films were prepared in a reactive environment of oxygen by sputtering an Al target. It was demonstrated that only a very small amount of oxygen passing through the cathode will oxidize (poison) the target, whereas large quantities of oxygen supplied externally to the cathode need not affect the target at all. A very stable discharge and ease of Al 2 O 3 formation were realized in this latter mode. The method was applied to the preparation of transparent, conductive films of ZnO doped with either Al or B. High deposition rates were achieved, and, at appropriate oxygen flow rates, low film resistivities. High-mobility In 2 O 3 :Mo transparent conductors were also prepared, with resistivities as low as 1.9x10 -4 Ω cm. Scaling relations for hollow cathodes, and deposition efficiency, and process comparisons between magnetron sputtering and linear, reactive-environment, hollow cathode sputtering are presented

Transcriptome analysis of Lactococcus lactis subsp. lactis during milk acidification as affected by dissolved oxygen and the redox potential.

Science.gov (United States)

Larsen, Nadja; Moslehi-Jenabian, Saloomeh; Werner, Birgit Brøsted; Jensen, Maiken Lund; Garrigues, Christel; Vogensen, Finn Kvist; Jespersen, Lene

2016-06-02

Performance of Lactococcus lactis as a starter culture in dairy fermentations depends on the levels of dissolved oxygen and the redox state of milk. In this study the microarray analysis was used to investigate the global gene expression of L. lactis subsp. lactis DSM20481(T) during milk acidification as affected by oxygen depletion and the decrease of redox potential. Fermentations were carried out at different initial levels of dissolved oxygen (dO2) obtained by milk sparging with oxygen (high dO2, 63%) or nitrogen (low dO2, 6%). Bacterial exposure to high initial oxygen resulted in overexpression of genes involved in detoxification of reactive oxygen species (ROS), oxidation-reduction processes, biosynthesis of trehalose and down-regulation of genes involved in purine nucleotide biosynthesis, indicating that several factors, among them trehalose and GTP, were implicated in bacterial adaptation to oxidative stress. Generally, transcriptional changes were more pronounced during fermentation of oxygen sparged milk. Genes up-regulated in response to oxygen depletion were implicated in biosynthesis and transport of pyrimidine nucleotides, branched chain amino acids and in arginine catabolic pathways; whereas genes involved in salvage of nucleotides and cysteine pathways were repressed. Expression pattern of genes involved in pyruvate metabolism indicated shifts towards mixed acid fermentation after oxygen depletion with production of specific end-products, depending on milk treatment. Differential expression of genes, involved in amino acid and pyruvate pathways, suggested that initial oxygen might influence the release of flavor compounds and, thereby, flavor development in dairy fermentations. The knowledge of molecular responses involved in adaptation of L. lactis to the shifts of redox state and pH during milk fermentations is important for the dairy industry to ensure better control of cheese production. Copyright © 2016 Elsevier B.V. All rights reserved.

Separation and recovery method for depleted uranium from spent fuel

International Nuclear Information System (INIS)

Imoto, Yoshie; Fujita, Reiko.

1993-01-01

Spent oxide fuels are reduced in a molten salt of CaCl 2 -CaF 2 to convert them into metals, then melted in an Fe-U bath disposed in an electrolytic refining vessel and brought into contact with molten Mg, to extract transuranium elements and rare earth elements contained in the Fe-U bath as metals in the molten Mg. Then molten Mg is removed and the residue is brought into contact with KCl-LiCl molten salt and electrolyzed using the Fe-U as an anode. Then, uranium is recovered by deposition on an iron cathode disposed in chloride electrolytes of the electrolytic refining vessel. Uranium and transuranium elements can be thus separated and, for example, depleted uranium for use in blanket fuels can be recovered easily. This can greatly reduce the temporary storage amount of depleted uranium, to eliminate requirement for a large-scaled facility used exclusively for storing uranium and long time management for uranium. (T.M.)

Health and environmental impact of depleted uranium

International Nuclear Information System (INIS)

Furitsu, Katsumi

2010-01-01

Depleted Uranium (DU) is 'nuclear waste' produced from the enrichment process and is mostly made up of 238 U and is depleted in the fissionable isotope 235 U compared to natural uranium (NU). Depleted uranium has about 60% of the radioactivity of natural uranium. Depleted uranium and natural uranium are identical in terms of the chemical toxicity. Uranium's high density gives depleted uranium shells increased range and penetrative power. This density, combined with uranium's pyrophoric nature, results in a high-energy kinetic weapon that can punch and burn through armour plating. Striking a hard target, depleted uranium munitions create extremely high temperatures. The uranium immediately burns and vaporizes into an aerosol, which is easily diffused in the environment. People can inhale the micro-particles of uranium oxide in an aerosol and absorb them mainly from lung. Depleted uranium has both aspects of radiological toxicity and chemical toxicity. The possible synergistic effect of both kinds of toxicities is also pointed out. Animal and cellular studies have been reported the carcinogenic, neurotoxic, immuno-toxic and some other effects of depleted uranium including the damage on reproductive system and foetus. In addition, the health effects of micro/ nano-particles, similar in size of depleted uranium aerosols produced by uranium weapons, have been reported. Aerosolized DU dust can easily spread over the battlefield spreading over civilian areas, sometimes even crossing international borders. Therefore, not only the military personnel but also the civilians can be exposed. The contamination continues after the cessation of hostilities. Taking these aspects into account, DU weapon is illegal under international humanitarian laws and is considered as one of the inhumane weapons of 'indiscriminate destruction'. The international society is now discussing the prohibition of DU weapons based on 'precautionary principle'. The 1991 Gulf War is reportedly the first

Novel results on fluence dependence and annealing behaviour of oxygenated and non-oxygenated silicon detectors

CERN Document Server

Martínez, C; Lozano, M; Campabadal, F; Santander, J; Fonseca, L; Ullán, M; Moreno, A

2002-01-01

This work presents the latest results on electrical properties degradation of silicon radiation detectors manufactured at IMB-CNM (Institut de Microelectronica de Barcelona) subjected to proton irradiation at CERN for high energy physics applications. The evolution of full depletion voltage and leakage current with fluence, as well as their annealing behaviour with time, were studied. The results obtained extend the previous understanding of the role played by technology and oxygenated material in hardening silicon radiation detectors. (15 refs).

"When the going gets tough, who keeps going?" Depletion sensitivity moderates the ego-depletion effect

NARCIS (Netherlands)

Salmon, Stefanie J.; Adriaanse, Marieke A.; De Vet, Emely; Fennis, Bob M.; De Ridder, Denise T D

2014-01-01

Self-control relies on a limited resource that can get depleted, a phenomenon that has been labeled ego-depletion. We argue that individuals may differ in their sensitivity to depleting tasks, and that consequently some people deplete their self-control resource at a faster rate than others. In

"When the going gets tough, who keeps going?" : Depletion sensitivity moderates the ego-depletion effect

NARCIS (Netherlands)

Salmon, Stefanie J.; Adriaanse, Marieke A.; De Vet, Emely; Fennis, Bob M.; De Ridder, Denise T. D.

2014-01-01

Self-control relies on a limited resource that can get depleted, a phenomenon that has been labeled ego-depletion. We argue that individuals may differ in their sensitivity to depleting tasks, and that consequently some people deplete their self-control resource at a faster rate than others. In

The modality effect of ego depletion: Auditory task modality reduces ego depletion.

Science.gov (United States)

Li, Qiong; Wang, Zhenhong

2016-08-01

An initial act of self-control that impairs subsequent acts of self-control is called ego depletion. The ego depletion phenomenon has been observed consistently. The modality effect refers to the effect of the presentation modality on the processing of stimuli. The modality effect was also robustly found in a large body of research. However, no study to date has examined the modality effects of ego depletion. This issue was addressed in the current study. In Experiment 1, after all participants completed a handgrip task, one group's participants completed a visual attention regulation task and the other group's participants completed an auditory attention regulation task, and then all participants again completed a handgrip task. The ego depletion phenomenon was observed in both the visual and the auditory attention regulation task. Moreover, participants who completed the visual task performed worse on the handgrip task than participants who completed the auditory task, which indicated that there was high ego depletion in the visual task condition. In Experiment 2, participants completed an initial task that either did or did not deplete self-control resources, and then they completed a second visual or auditory attention control task. The results indicated that depleted participants performed better on the auditory attention control task than the visual attention control task. These findings suggest that altering task modality may reduce ego depletion. © 2016 Scandinavian Psychological Associations and John Wiley & Sons Ltd.

Mineralogy and origin of surficial uranium deposits hosted in travertine and calcrete from central Jordan

International Nuclear Information System (INIS)

Khoury, H.N.; Salameh, E.M.; Clark, I.D.

2014-01-01

Highlights: • Surficial uranium deposits are hosted in thick travertine and calcrete. • Tyuyamunite–strelkinite are the major components in central Jordan. • The leached water was enriched in redox sensitive U and V. • Deposition is related to unusual highly alkaline circulating water. - Abstract: Secondary uranium encrustations are hosted in thick travertine and calcrete deposits of Pleistocene–Recent age in central Jordan. The central Jordan varicolored marble and travertine are equivalent to the active metamorphic area in Maqarin, north Jordan. More than 100 samples were collected from the outcrops of the varicolored marble, travertine, calcrete, and the yellow uranium encrustations. The secondary yellow encrustations are mainly composed of uranyl vanadate complexes. Tyuyamunite Ca(UO 2 ) 2 V 2 5+ O 8 ·3(H 2 O)–strelkinite Na 2 (UO 2 ) 2 V 2 O 8 ·6(H 2 O) solid solution series are the major components and their composition reflects changes in the Ca/Na ratio in solution. Potentially, new vanadium free calcium uranate phases (restricted to the varicolored marble) were identified with CaO:UO 3 ratios different from the known mineral vorlanite (CaU 6+ )O 4 . Carbon and oxygen isotope data from calcite in the varicolored marble are characterized by Rayleigh-type enrichment in light isotopes associated with release of 13 C and 18 O enriched CO 2 by high temperature decarbonation during combustion of the bituminous marl. Stable isotope results from uranium hosted travertine and calcrete varieties exhibit a wide range in isotopic values, between decarbonated and normal sedimentary carbonate rocks. The depleted δ 13 C and δ 18 O values in the travertine are related to the kinetic reaction of atmospheric CO 2 with hyperalkaline Ca(OH) 2 water. The gradual enrichment of δ 13 C and δ 18 O values in the calcrete towards equilibrium with the surrounding environment is related to continuous evaporation during seasonal dry periods. Uranium mineralization in

Electrical conductivity and oxygen exchange kinetics of La2NiO4+delta thin films grown by chemical vapor deposition

DEFF Research Database (Denmark)

Garcia, G.; Burriel, M.; Bonanos, Nikolaos

2008-01-01

Epitaxial c-axis oriented La2NiO4+delta films were deposited onto SrTiO3 and NdGaO3 substrates by the pulsed injection metal organic chemical vapor deposition technique. Experimental conditions were optimized in order to accurately control the composition, thickness, and texture of the layers. X......-ray diffraction was used to confirm the high crystalline quality of the obtained material. Electrical characterizations were performed on thin (50 nm) and thick (335 nm) layers. The total specific conductivity, which is predominantly electronic, was found to be larger for the thinner films measured (50 nm......), probably due to the effect of the strain present in the layers. Those thin films (50 nm) showed values even larger than those observed for single crystals and, to our knowledge, are the largest conductivity values reported to date for the La2NiO4+delta material. The oxygen exchange kinetics was studied...

The properties of nanocomposite aluminium-silicon based thin films deposited by filtered arc deposition

Energy Technology Data Exchange (ETDEWEB)

Bendavid, A.; Martin, P.J.; Takikawa, H

2002-12-02

Thin films of aluminium silicon oxynitride have been deposited on conducting (100) silicon wafers by filtered arc deposition (FAD) under nitrogen and/or oxygen gas flow. The influence of the N{sub 2}/O{sub 2} flow ratio on the crystal structure, optical and mechanical properties has been investigated. The results of X-ray diffraction showed that the film structure comprised of an AlN crystallite with amorphous Si{sub 3}N{sub 4} and SiO{sub x}. The optical properties over the range of 350-800 nm were measured using spectroscopic ellipsometry and found to be strongly dependent on N{sub 2}/O{sub 2} flow ratio. The refractive index values of the films were measured to be in the range of 2.2-1.64 at a wavelength of 670 nm for oxygen flow range of 0-100%. The hardness of the films was found to be strongly dependent on the oxygen content in the film. The hardness range of the films was between 10 and 22 GPa and for the stress between 0.3 and 1.2 GPa.

Characteristics of chlorites from Huangnihu uranium deposit and their implications in uranium metallogenic environment in the southern part of Jiangxi Province

International Nuclear Information System (INIS)

Hu Zhihua; Lin Jinrong; Pang Yaqing; Gao Fei; Rong Jiashu; Guo Shuying

2013-01-01

Chlorite is genetically related to uranium mineralization in Huangnihu uranium deposit. By means of microscopic and electronic microprobe analysis, the authors investigated chemical composition and texture of the chlorite and found that chlorite in Huangnihu deposit has the following characteristics: 1. they are mainly Fe-rich chlorite composed of chamosite and brunsvigite, of which chemical composition is mainly affected by mud and mafic rock; 2. the Fe-Mg and Al"I"V-Si substitution dominates the octahedral substitution supplemented by Al"V"I-Fe substitution; the oolitic chlorite and biotite feinted chlorite closely associated with uranium were formed at temperatures of 216.23 ∼ 256.73℃ (average 228.6℃). The chemical composition and forming environment of the oolitic chlorite and biotite illusion chlorite suggests that Huangnihu uranium deposit is a low-moderate temperature hydrothermal uranium deposit formed in a reducing environment and iron-rich formation, the ore-forming fluid mainly originated from shale rock, partly from ultramafic or mafic liquid. (authors)

Faunal and oxygen isotopic evidence for surface water salinity changes during sapropel formation in the eastern Mediterranean