International Nuclear Information System (INIS)
Andrews, M.G.
1978-01-01
A nuclear fuel pin has positioned within it material which will decompose to release an oxidizing agent which will react with the cladding of the pin and form a protective oxide film on the internal surface of the cladding
Transient survivability of LMR oxide fuel pins
International Nuclear Information System (INIS)
Weber, E.T.; Pitner, A.L.; Bard, F.E.; Culley, G.E.; Hunter, C.W.
1986-01-01
Fuel pin integrity during transient events must be assessed for both the core design and safety analysis phases of a reactor project. A significant increase in the experience related to limits of integrity for oxide fuel pins in transient overpower events has been realized from testing of fuel pins irradiated in FFTF and PFR. Fourteen FFTF irradiated fuel pins were tested in TREAT, representing a range of burnups, overpower ramp rates and maximum overpower conditions. Results of these tests along with similar testing in the PFR/TREAT program, provide a demonstration of significant safety margins for oxide fuel pins. Useful information applied in analytical extrapolation of fuel pin test data have been developed from laboratory transient tests on irradiated fuel cladding (FCTT) and on unirradiated fuel pellet deformation. These refinements in oxide fuel transient performance are being applied in assessment of transient capabilities of long lifetime fuel designs using ferritic cladding
Reirradiation of mixed-oxide fuel pins at increased temperatures
International Nuclear Information System (INIS)
Lawrence, L.A.; Weber, E.T.
1976-05-01
Mixed-oxide fuel pins from EBR-II irradiations were reirradiated in the General Electric Test Reactor (GETR) at higher temperatures than experienced in EBR-II to study effects of the increased operating temperatures on thermal/mechanical and chemical behavior. The response of a mixed-oxide fuel pin to a power increase after having operated at a lower power for a significant portion of its life-time is an area of performance evaluation where little information currently exists. Results show that the cladding diameter changes resulting from the reirradiation are strongly dependent upon both prior burnup level and the magnitude of the temperature increase. Results provide the initial rough outlines of boundaries within which mixed-oxide fuel pins can or cannot tolerate power increases after substantial prior burnup at lower powers
Performance of advanced oxide fuel pins in EBR-II
International Nuclear Information System (INIS)
Lawrence, L.A.; Jensen, S.M.; Hales, J.W.; Karnesky, R.A.; Makenas, B.J.
1986-05-01
The effects of design and operating parameters on mixed-oxide fuel pin irradiation performance were established for the Hanford Engineering Development Laboratory (HEDL) advanced oxide EBR-II test series. Fourteen fuel pins breached in-reactor with reference 316 SS cladding. Seven of the breaches are attributed to FCMI. Of the remaining seven breached pins, three are attributed to local cladding over-temperatures similar to the breach mechanism for the reference oxide pins irradiated in EBR-II. FCCI was found to be a contributing factor in two high burnup, i.e., 11.7 at. % breaches. The remaining two breaches were attributed to mechanical interaction of UO 2 fuel and fission products accumulated in the lower cladding insulator gap, and a loss of cladding ductility possibly due to liquid metal embrittlement. Fuel smear density appears to have the most significant impact on lifetime. Quantitative evaluations of cladding diameter increases attributed to FCMI, established fuel smear density, burnup, and cladding thickness-to-diameter ratio as the major parameters influencing the extent of cladding strain
Energy Technology Data Exchange (ETDEWEB)
Lieblich, M; Lopez, J
1987-07-01
In the frame of the Joint Irradiation Program IVO-FR2-Vg7 between the Centre of Nuclear Research of Karlsruhe (KfK), the irradiation of 30 mixed-oxide fuel rods in the FR2 experimental reactor was carried out. The pins were located in 10 single-walled NaK capsules. The behaviour of the fuel during its burnup was studied, mainly, the rest-porosity and cracking distribution in the pellet, partial densification, etc. In this work 3 pins from the capsule No. 165 were analyzed. The experimental results (pore and cracking profiles) were interpreted by the fuel rod code SATURN. (Author) 20 refs.
Fabrication of oxide dispersion strengthened ferritic clad fuel pins
International Nuclear Information System (INIS)
Zirker, L.R.; Bottcher, J.H.; Shikakura, S.; Tsai, C.L.
1991-01-01
A resistance butt welding procedure was developed and qualified for joining ferritic fuel pin cladding to end caps. The cladding are INCO MA957 and PNC ODS lots 63DSA and 1DK1, ferritic stainless steels strengthened by oxide dispersion, while the end caps are HT9 a martensitic stainless steel. With adequate parameter control the weld is formed without a residual melt phase and its strength approaches that of the cladding. This welding process required a new design for fuel pin end cap and weld joint. Summaries of the development, characterization, and fabrication processes are given for these fuel pins. 13 refs., 6 figs., 1 tab
Analysis of fuel cladding chemical interaction in mixed oxide fuel pins
International Nuclear Information System (INIS)
Weber, J.W.; Dutt, D.S.
1976-01-01
An analysis is presented of the observed interaction between mixed oxide 75 wt percent UO 2 --25 wt percent PuO 2 fuel and 316--20 percent CW stainless steel cladding in LMFBR type fuel pins irradiated in EBR-II. A description is given of the test pins and their operating conditions together with, metallographic observations and measurements of the fuel/cladding reaction, and a correlation equation is developed relating depth of cladding attack to temperature and burnup. Some recent data on cladding reaction in fuel pins with low initial O/M in the fuel are given and compared with the correlation equation curves
Program of quality management when fabricating fast reactor vibropack oxide fuel pins
International Nuclear Information System (INIS)
Mayorshin, A.A.; Kisly, V.A.; Sudakov, L.V.
2000-01-01
There are presented main principles of creation and operation of Quality Management Program in fabricating vibropack oxide fuel pins for BOR-60 and BN-600 being in force in SSC RF RIAR. There is given structure of documentation for QS principal elements. Under Quality System there are defined all the procedures, assuring that fuel pin meets the normative requirements. The system model is complied with the standard model IS 9001. There are shown technologic flowchart and check operation, statistic results of pin critical parameter check as well as main results of in-pile tests. (author)
Analysis of the porosity distribution of mixed oxide pins
International Nuclear Information System (INIS)
Lieblich, M.; Lopez, J.
1987-01-01
In the frame of the Joint Irradiation Program IVO-FR2-Vg7 between the Centre of Nuclear Research of Karlsruhe (KfK), the irradiation of 30 mixed-oxide fuel rods in the FR2 experimental reactor was carried out. The pins were located in 10 single-walled NaK capsules. The behaviour of the fuel during its burnup was studied, mainly, the rest-porosity and cracking distribution in the pellet, partial densification, etc. In this work 3 pins from the capsule No. 165 were analyzed. The experimental results (pore and cracking profiles) were interpreted by the fuel rod code SATURN. (Author) 20 refs
Oxide fuel pin transient performance analysis and design with the TEMECH code
International Nuclear Information System (INIS)
Bard, F.E.; Dutt, S.P.; Hinman, C.A.; Hunter, C.W.; Pitner, A.L.
1986-01-01
The TEMECH code is a fast-running, thermal-mechanical-hydraulic, analytical program used to evaluate the transient performance of LMR oxide fuel pins. The code calculates pin deformation and failure probability due to fuel-cladding differential thermal expansion, expansion of fuel upon melting, and fission gas pressurization. The mechanistic fuel model in the code accounts for fuel cracking, crack closure, porosity decrease, and the temperature dependence of fuel creep through the course of the transient. Modeling emphasis has been placed on results obtained from Fuel Cladding Transient Test (FCTT) testing, Transient Fuel Deformation (TFD) tests and TREAT integral fuel pin experiments
Performance of IN-706 and PE-16 cladding in mixed-oxide fuel pins
International Nuclear Information System (INIS)
Makenas, B.J.; Lawrence, L.A.; Jensen, B.W.
1982-05-01
Iron-nickel base, precipitation-strengthened alloys, IN-706 and PE-16, advanced alloy cladding considered for breeder reactor applications, were irradiated in mixed-oxide fuel pins in the HEDL-P-60 subassembly in EBR-II. Initial selection of candidate advanced alloys was done using only nonfueled materials test results. However, to establish the performance characteristics of the candidate cladding alloys, i.e., dimensional stability and structural integrity under conditions of high neutron flux, elevated temperature, and applied stress, it was necessary to irradiate fuel pins under typical operating conditions. Fuel pins were clad with solution treated IN-706 and PE-16 and irradiated to peak fluences of 6.1 x 10 22 n/cm 2 (E > .1 MeV) and 8.8 x 10 22 n/cm 2 (E > .1 MeV) respectively. Fabrication and operating parameters for the fuel pins with the advanced cladding alloy candidates are summarized. Irradiation of HEDL-P-60 was interrupted with the breach of a pin with IN-706 cladding at 5.1 at % and the test was terminated with cladding breach in a pin with PE-16 cladding at 7.6 at %
Investigations of fuel cladding chemical interaction in irradiated LMFBR type oxide fuel pins
International Nuclear Information System (INIS)
Roake, W.E.; Adamson, M.G.; Hilbert, R.F.; Langer, S.
1977-01-01
Understanding and controlling the chemical attack of fuel pin cladding by fuel and fission products are major objectives of the U.S. LMFBR Mixed Oxide Irradiation Testing Program. Fuel-cladding chemical interaction (FCCI) has been recognized as an important factor in the ability to achieve goal peak burnups of 8% (80.MWd/kg) in FFTF and in excess of 10% (100.MWd/kg) in the LMFBR demonstration reactors while maintaining coolant bulk outlet temperatures up to ∼60 deg. C (1100 deg. F). In this paper we review pertinent parts of the irradiation program and describe recent observation of FCCI in the fuel pins of this program. One goal of the FCCI investigations is to obtain a sufficiently quantitative understanding of FCCI such that correlations can be developed relating loss of effective cladding thickness to irradiation and fuel pin fabrication parameters. Wastage correlations being developed using different approaches are discussed. Much of the early data on FCCI obtained in the U.S. Mixed Oxide Fuel Program came from capsule tests irradiated in both fast and thermal flux facilities. The fast flux irradiated encapsulated fuel pins continue to provide valuable data and insight into FCCI. Currently, however, bare pins with prototypic fuels and cladding irradiated in the fast flux Experimental Breeder Reactor-II (EBR-II) as multiple pin assemblies under prototypic powers, temperatures and thermal gradients are providing growing quantities of data on FCCI characteristics and cladding thickness losses from FCCI. A few special encapsulated fuel pin tests are being conducted in the General Electric Test Reactor (GETR) and EBR-II, but these are aimed at providing specific information under irradiation conditions not achievable in the fast flux bare pin assemblies or because EBR-II Operation or Safety requirements dictate that the pins be encapsulated. The discussion in this paper is limited to fast flux irradiation test results from encapsulated pins and multiple pin
Investigations of fuel cladding chemical interaction in irradiated LMFBR type oxide fuel pins
Energy Technology Data Exchange (ETDEWEB)
Roake, W E [Westinghouse-Hanford Co., Richland, WA (United States); Adamson, M G [General Electric Company, Vallecitos Nuclear Center, Pleasanton, CA (United States); Hilbert, R F; Langer, S
1977-04-01
Understanding and controlling the chemical attack of fuel pin cladding by fuel and fission products are major objectives of the U.S. LMFBR Mixed Oxide Irradiation Testing Program. Fuel-cladding chemical interaction (FCCI) has been recognized as an important factor in the ability to achieve goal peak burnups of 8% (80.MWd/kg) in FFTF and in excess of 10% (100.MWd/kg) in the LMFBR demonstration reactors while maintaining coolant bulk outlet temperatures up to {approx}60 deg. C (1100 deg. F). In this paper we review pertinent parts of the irradiation program and describe recent observation of FCCI in the fuel pins of this program. One goal of the FCCI investigations is to obtain a sufficiently quantitative understanding of FCCI such that correlations can be developed relating loss of effective cladding thickness to irradiation and fuel pin fabrication parameters. Wastage correlations being developed using different approaches are discussed. Much of the early data on FCCI obtained in the U.S. Mixed Oxide Fuel Program came from capsule tests irradiated in both fast and thermal flux facilities. The fast flux irradiated encapsulated fuel pins continue to provide valuable data and insight into FCCI. Currently, however, bare pins with prototypic fuels and cladding irradiated in the fast flux Experimental Breeder Reactor-II (EBR-II) as multiple pin assemblies under prototypic powers, temperatures and thermal gradients are providing growing quantities of data on FCCI characteristics and cladding thickness losses from FCCI. A few special encapsulated fuel pin tests are being conducted in the General Electric Test Reactor (GETR) and EBR-II, but these are aimed at providing specific information under irradiation conditions not achievable in the fast flux bare pin assemblies or because EBR-II Operation or Safety requirements dictate that the pins be encapsulated. The discussion in this paper is limited to fast flux irradiation test results from encapsulated pins and multiple pin
Cesium migration in LMFBR fuel pins
International Nuclear Information System (INIS)
Karnesky, R.A.; Jost, J.W.; Stone, I.Z.
1978-10-01
The factors affecting the axial migration of cesium in mixed oxide fuel pins and the effects of cesium migration on fuel pin performance are examined. The development and application of a correlated model which will predict the occurrence of cesium migration in a mixed oxide (75 w/o UO 2 + 25 w/o PuO 2 ) fuel pins over a wide range of fabrication and irradiation conditions are described
Performance of fast reactor mixed-oxide fuels pins during extended overpower transients
International Nuclear Information System (INIS)
Tsai, H.; Neimark, L.A.; Asaga, T.; Shikakura, S.
1991-02-01
The Operational Reliability Testing (ORT) program, a collaborative effort between the US Department of Energy and the Power Reactor and Nuclear Fuel Development Corp. (PNC) of Japan, was initiated in 1982 to investigate the behavior of mixed-oxide fuel pin under various slow-ramp transient and duty-cycle conditions. In the first phase of the program, a series of four extended overpower transient tests, with severity sufficient to challenge the pin cladding integrity, was conducted. The objectives of the designated TOPI-1A through -1D tests were to establish the cladding breaching threshold and mechanisms, and investigate the thermal and mechanical effects of the transient on pin behavior. The tests were conducted in EBR-2, a normally steady-state reactor. The modes of transient operation in EBR-2 were described in a previous paper. Two ramp rates, 0.1%/s and 10%/s, were selected to provide a comparison of ramp-rate effects on fuel behavior. The test pins chosen for the series covered a range of design and pre-test irradiation parameters. In the first test (1A), all pins maintained their cladding integrity during the 0.1%/s ramp to 60% peak overpower. Fuel pins with aggressive designs, i.e., high fuel- smear density and/or thin cladding, were, therefore, included in the follow-up 1B and 1C tests to enhance the likelihood of achieving cladding breaching. In the meantime, a higher pin overpower capability, to greater than 100%, was established by increasing the reactor power limit from 62.5 to 75 MWt. In this paper, the significant results of the 1B and 1C tests are presented. 4 refs., 5 figs., 1 tab
High dose stainless steel swelling data on interior and peripheral oxide fuel pins
International Nuclear Information System (INIS)
Boltax, A.; Foster, J.P.; Nayak, U.P.
1983-01-01
High dose (2 x 10 23 n/cm 2 , E > 0.1 Mev) swelling data obtained on 20% cold-worked AISI 316 stainless steel (N-lot) cladding from mixed-oxide fuel pins show large differences in swelling incubation dose due to pre-incubation dose temperature changes. Circumferential swelling variations of 1.5 to 4 times were found in peripheral fuel pin cladding which experienced 30 to 60 deg C temperature changes due to movement in a temperature gradient. Consideration is given to the implications of these results to low swelling materials development and core design. (author)
Motowidlo, L. R.; Lee, P. J.; Tarantini, C.; Balachandran, S.; Ghosh, A. K.; Larbalestier, D. C.
2018-01-01
We report on the development of multifilamentary Nb3Sn superconductors by a versatile powder-in-tube technique (PIT) that demonstrates a simple pathway to a strand with a higher density of flux-pinning sites that has the potential to increase critical current density beyond present levels. The approach uses internal oxidation of Zr-alloyed Nb tubes to produce Zr oxide particles within the Nb3Sn layer that act as a dispersion of artificial pinning centres (APCs). In this design, SnO2 powder is mixed with Cu5Sn4 powder within the PIT core that supplies the Sn for the A15 reaction with Nb1Zr filament tubes. Initial results show an average grain size of ˜38 nm in the A15 layer, compared to the 90-130 nm of typical APC-free high-J c strands made by conventional PIT or Internal Sn processing. There is a shift in the peak of the pinning force curve from H/H irr of ˜0.2 to ˜0.3 and the pinning force curves can be deconvoluted into grain boundary and point-pinning components, the point-pinning contribution dominating for the APC Nb-1wt%Zr strands.
International Nuclear Information System (INIS)
Baker, R.B.; Wilson, D.R.
1986-04-01
The SIEX3 computer program was developed to calculate the fuel and cladding performance of oxide fuel and oxide blanket pins irradiated in the fast neutron environment of a liquid metal cooled reactor. The code is uniquely designed to be accurate yet quick running and use a minimum of computer core storage. This was accomplished through the correlation of physically based models to very large data bases of irradiation test results. Data from over 200 fuel pins and over 800 transverse fuel microscopy samples were used in the calibrations
International Nuclear Information System (INIS)
Panakkal, J.P.; Ghosh, J.K.; Roy, P.R.
1989-01-01
Nondestructive evaluation of nuclear fuel pellets after the welding of fuel pins plays a vital role in assuring a safe and reliable operation of reactors. Some of the important characteristics to be monitored in low plutonium enriched mixed oxide fuel pellets are plutonium enrichment, size of plutonium dioxide agglomerates, incorrect loading and geometric shape. Experiments were carried out at Bhabha Atomic Research Centre, Bombay on experimental fuel pins containing mixed oxide pellets of different geometry (solid and annular), of different plutonium enrichment (0-6 w% of plutonium dioxide) and containing PuO 2 agglomerates of size 125-2000 microns to evaluate these characteristics nondestructively. Neutron radiography of these fuel pins was carried out using a swimming pool type reactor 'APSARA'. Results of quantitative evaluation of the neutron radiographs and a simple model correlating neutron interaction probability and the optical density are presented. Gamma autoradiography of these fuel pins showed that these parameters could be evaluated with a few limitations. This paper presents the experimental details, quantitative analysis of the radiographs by microdensitometry and merits and demerits of neutron radiography and gamma autoradiography for nondestructive charcterisation of nuclear fuel pellets. (orig.)
International Nuclear Information System (INIS)
Liu, Y.Y.; Tsai, H.C.; Donahue, D.A.; Pushis, D.O.; Savoie, F.E.; Holland, J.W.; Wright, A.E.; August, C.; Bailey, J.L.; Patterson, D.R.
1990-05-01
The whole-pin furnace system is a new in-cell experimental facility constructed to investigate how irradiated fuel pins may fail under potential reactor accident conditions. Extensive checkouts have demonstrated excellent performance in remote operation, temperature control, pin breach detection, and fission gas handling. The system is currently being used in testing of EBIR-II-irradiated Integral Fast Reactor (IFR) metal fuel pins; future testing will include EBR-II-irradiated mixed-oxide fuel pins. 7 refs., 4 figs
Cesium relocation in mixed-oxide fuel pins resulting from increased temperature reirradiation
International Nuclear Information System (INIS)
Lawrence, L.A.; Woodley, R.E.; Weber, E.T.
1976-06-01
Mixed-oxide fuel pins from EBR-II test subassemblies PNL-3 and PNL-4 were reirradiated in the GETR to study effects of increased fuel and cladding temperatures on chemical and thermomechanical behavior. Radial and axial distributions of cesium were obtained using postirradiation nondestructive precision gamma-scanning techniques. Data presented relate to the dependence of cesium distribution and transport processes on temperature gradients which were altered after substantial steady-state operation
Defect pin behaviour in the DFR
International Nuclear Information System (INIS)
Sloss, W.M.; Bagley, K.Q.; Edmonds, E.; Potter, P.E.
1979-01-01
A program of defective fuel pin irradiations has been carried out in the DFR. This program employed fuel pins which had failed during previous irradiations (natural defects) and pins in which simulated failures (artificial defects) had been induced prior to irradiation or during an intermediate examination stage at moderate or substantial burnups. The artificial defects simulated longitudinal ruptures and were normally located at positions near the top, middle and bottom of the pin where clad temperatures were 450, 540 and 630 0 C respectively. The fuel was mixed U-Pu oxide, and fuel form, stoichiometry, clad type, pin diameter, linear rating, and burnup were among the variables examined. The defect pin tests were normally carried out in single pin or trefoil type vehicles. After irradiation all the pins were subjected to the normal nondestructive examination procedures and the visual, radiographic, gamma-scanning, and dimensional change results are presented. Several pins were destructively examined and the metallographic data are discussed
Mode of failure of LMFBR fuel pins
International Nuclear Information System (INIS)
Washburn, D.F.
1975-01-01
The objectives of the irradiation test described were to evaluate mixed-oxide fuel performance and to confirm the design adequacy of the FFTF fuel pins. After attainment of the initial objectives the irradiation of several of the original fuel pins was continued until a cladding breach occurred. The consequences of a cladding breach were evaluated by reconstituting the original 37-pin subassembly into two 19-pin subassemblies after a burnup at 50,000 MWd/MTM (5.2 a/o). The original pins were supplemented with fresh pins as necessary. Irradiation of the subassemblies was continued until a cladding breach occurred. Results are presented and discussed
Fuel-pin cladding transient failure strain criterion
International Nuclear Information System (INIS)
Bard, F.E.; Duncan, D.R.; Hunter, C.W.
1983-01-01
A criterion for cladding failure based on accumulated strain was developed for mixed uranium-plutonium oxide fuel pins and used to interpret the calculated strain results from failed transient fuel pin experiments conducted in the Transient Reactor Test (TREAT) facility. The new STRAIN criterion replaced a stress-based criterion that depends on the DORN parameter and that incorrectly predicted fuel pin failure for transient tested fuel pins. This paper describes the STRAIN criterion and compares its prediction with those of the stress-based criterion
Thermochemical aspects of fuel-cladding and fuel-coolant interactions in LMFBR oxide fuel pins
International Nuclear Information System (INIS)
Adamson, M.G.; Aitken, E.A.; Caputi, R.W.; Potter, P.E.; Mignanelli, M.A.
1979-01-01
This paper examines several thermochemical aspects of the fuel-cladding, fuel-coolant and fuel-fission product interactions that occur in LMFBR austenitic stainless steel-clad mixed (U,Pu)-oxide fuel pins during irradiation under normal operating conditions. Results are reported from a variety of high temperature EMF cell experiments in which continuous oxygen activity measurements on reacting and equilibrium mixtures of metal oxides and (excess) liquid alkali metal (Na, K, Cs) were performed. Oxygen potential and 0:M thresholds for Na-fuel reactions are re-evaluated in the light of new measurements and newly-assessed thermochemical data, and the influence on oxygen potential of possible U-Pu segregation between oxide and urano-plutonate (equilibrium) phases has been analyzed. (orig./RW) [de
Neutron radiography of fuel pins
International Nuclear Information System (INIS)
Jackson, C.N. Jr.; Powers, H.G.; Burgess, C.A.
1975-01-01
Neutron radiography performed with a reactor source has been shown to be a superior radiographic method for the examination of unirradiated mixed oxide fuel pins at the Hanford Engineering Development Laboratory. Approximately 1,700 fuel pins were contained in a sample that demonstrated the capability of the method for detecting laminations, structural flaws, fissile density variation, hydrogenous inclusions and voids in assembled fuel pins. The nature, extent, and importance of the detected conditions are substantiated by gamma autoradiography and by destructive analysis employing alpha autoradiography, electron microprobe and visual inspection. Also, a series of radiographs illustrate the response of neutron radiography as compared to low voltage and high voltage x-ray and gamma source Iridium 192 radiography. (U.S.)
Design fix for vibration-induced wear in fuel pin bundles
International Nuclear Information System (INIS)
Naas, D.F.; Heck, E.N.
1976-01-01
In summary, results at 45,000 MWd/MTM burnup from the FFTF mixed oxide fuel pin irradiation tests in EBR-II show that reduction of the initial fuel pin bundle clearance and use of 20 percent cold-worked stainless steel ducts virtually eliminate vibration and wear observed in an initial series of 61-pin tests
Flux pinning by voids in surface-oxidized superconducting niobium and vanadium
International Nuclear Information System (INIS)
Meij, G.P. van der.
1984-03-01
The volume pinning force in several niobium and vanadium samples with voids is determined at various temperatures. Reasonable agreement is found with the collective pinning theory of Larkin and Ovchinnikov above the field of maximum pinning, if the flux line lattice is assumed to be amorphous in this region and if the elementary pinning force is calculated from the quasi-classical theory of Thuneberg, Kurkijaervi, and Rainer. Also some history and relaxation effects are studied in an alternating field. A qualitative explanation is given in terms of flux line dislocations, which reduce the shear strength of the flux line lattice. (Auth.)
Pinning, de-pinning and re-pinning of a slowly varying rivulet
Paterson, C.; Wilson, S.K.; Duffy, B.R.
2013-01-01
The solutions for the unidirectional flow of a thin rivulet with prescribed volume flux down an inclined planar substrate are used to describe the locally unidirectional flow of a rivulet with constant width (i.e. pinned contact lines) but slowly varying contact angle as well as the possible pinning and subsequent de-pinning of a rivulet with constant contact angle and the possible de-pinning and subsequent re-pinning of a rivulet with constant width as they flow in the azimuthal direction from the top to the bottom of a large horizontal cylinder. Despite being the same locally, the global behaviour of a rivulet with constant width can be very different from that of a rivulet with constant contact angle. In particular, while a rivulet with constant non-zero contact angle can always run from the top to the bottom of the cylinder, the behaviour of a rivulet with constant width depends on the value of the width. Specifically, while a narrow rivulet can run all the way from the top to the bottom of the cylinder, a wide rivulet can run from the top of the cylinder only to a critical azimuthal angle. The scenario in which the hitherto pinned contact lines of the rivulet de-pin at the critical azimuthal angle and the rivulet runs from the critical azimuthal angle to the bottom of the cylinder with zero contact angle but slowly varying width is discussed. The pinning and de-pinning of a rivulet with constant contact angle, and the corresponding situation involving the de-pinning and re-pinning of a rivulet with constant width at a non-zero contact angle which generalises the de-pinning at zero contact angle discussed earlier, are described. In the latter situation, the mass of fluid on the cylinder is found to be a monotonically increasing function of the constant width. © 2013 Elsevier Masson SAS. All rights reserved.
Pinning, de-pinning and re-pinning of a slowly varying rivulet
Paterson, C.
2013-09-01
The solutions for the unidirectional flow of a thin rivulet with prescribed volume flux down an inclined planar substrate are used to describe the locally unidirectional flow of a rivulet with constant width (i.e. pinned contact lines) but slowly varying contact angle as well as the possible pinning and subsequent de-pinning of a rivulet with constant contact angle and the possible de-pinning and subsequent re-pinning of a rivulet with constant width as they flow in the azimuthal direction from the top to the bottom of a large horizontal cylinder. Despite being the same locally, the global behaviour of a rivulet with constant width can be very different from that of a rivulet with constant contact angle. In particular, while a rivulet with constant non-zero contact angle can always run from the top to the bottom of the cylinder, the behaviour of a rivulet with constant width depends on the value of the width. Specifically, while a narrow rivulet can run all the way from the top to the bottom of the cylinder, a wide rivulet can run from the top of the cylinder only to a critical azimuthal angle. The scenario in which the hitherto pinned contact lines of the rivulet de-pin at the critical azimuthal angle and the rivulet runs from the critical azimuthal angle to the bottom of the cylinder with zero contact angle but slowly varying width is discussed. The pinning and de-pinning of a rivulet with constant contact angle, and the corresponding situation involving the de-pinning and re-pinning of a rivulet with constant width at a non-zero contact angle which generalises the de-pinning at zero contact angle discussed earlier, are described. In the latter situation, the mass of fluid on the cylinder is found to be a monotonically increasing function of the constant width. © 2013 Elsevier Masson SAS. All rights reserved.
One- and two-dimension effects on fuel pin lifetime
International Nuclear Information System (INIS)
Stephen, J.D.; Biancheria, A.; Leibnitz, D.; O'Reilly, B.D.; Liu, Y.Y.; Labar, M.P.; Gneiting, B.C.
1979-01-01
Lifetime, or breach of the cladding, is a difficult performance limit to establish in fuel pin design. The significant benefits of high plant capacity factor favor conservative design to eliminate downtime or partial power operation caused by the breach limit; however, overly conservative design produces significant penalties. The LIFE system is being applied to help understand the range between operation and breach so that appropriate design margins can be selected. Standards are being developed in the USA to assure the structural integrity of all core components. These standards will provide guidelines to account for the failure mechanisms observed in the high temperature, high fluence core environment. The work to date indicates that creep rupture is the most important failure mechanism for mixed-oxide fuel pins during normal operation and slow power changes. The local cumulative creep rupture damage fraction (CDF) has been adopted as the parameter to assess the approach to failure. Several oxide breached pins and siblings have been studied For example, the P23B-73 pin was an FFTR driver design pin irradiated in EBR-II which failed at 10 at,% burnup. Initial evaluation based on LIFE3 led to the conclusion that the pin should not have failed. Further analyses determined the sensitivity of the breach prediction to the time-to-rupture correlation, cladding temperature, and fuel-fission product swelling (which had not been modeled in LIFE3). The uncertainties in the time-to-rupture correlation have been established. But LIFE is a one-dimensional model. The TWOD code is complete, and development of the best way to couple LIFE and TWOD for lifetime analysis is in progress. Two preliminary conclusions from analysis of representative oxide pin geometries are, first, that the circumferential stress distribution may not peak at the hot spot, but the damage (CDF) does. And second, that the effect of stress concentrations near fuel cracks on cladding creep damage is small
International Nuclear Information System (INIS)
Strain, R.V.; Johnson, C.E.
1978-05-01
Postirradiation examinations were performed on five fuel pins from the Gas-Cooled Fast-Breeder Reactor F-1 experiment irradiated in EBR-II to a peak burnup of approximately 5.5 at. %. These encapsulated fuel pins were irradiated at peak-power linear ratings from approximately 13 to 15 kW/ft and peak cladding inside diameter temperatures from approximately 625 to 760 0 C. The maximum diametral change that occurred during irradiation was 0.2% ΔD/D 0 . The maximum fuel-cladding chemical interaction depth was 2.6 mils in fuel pin G-1 and 1 mil or less in the other three pins examined destructively. Significant migration of the volatile fission products occurred axially to the fuel-blanket interfaces. Teh postirradiation examination data indicate that fuel melted at the inner surface of the annular fuel pellets in the two highest power rating fuel pins, but little axial movement of fuel occurred
Energy Technology Data Exchange (ETDEWEB)
Strain, R V; Johnson, C E
1978-05-01
Postirradiation examinations were performed on five fuel pins from the Gas-Cooled Fast-Breeder Reactor F-1 experiment irradiated in EBR-II to a peak burnup of approximately 5.5 at. %. These encapsulated fuel pins were irradiated at peak-power linear ratings from approximately 13 to 15 kW/ft and peak cladding inside diameter temperatures from approximately 625 to 760/sup 0/C. The maximum diametral change that occurred during irradiation was 0.2% ..delta..D/D/sub 0/. The maximum fuel-cladding chemical interaction depth was 2.6 mils in fuel pin G-1 and 1 mil or less in the other three pins examined destructively. Significant migration of the volatile fission products occurred axially to the fuel-blanket interfaces. Teh postirradiation examination data indicate that fuel melted at the inner surface of the annular fuel pellets in the two highest power rating fuel pins, but little axial movement of fuel occurred.
Anisotropic vortex pinning in the β-pyrochlore oxide superconductor KOs 2O 6
Ishii, Y.; Yamaura, J.; Okamoto, Y.; Maeda, A.; Hiroi, Z.
2011-11-01
Vortex pinning in the β-pyrochlore oxide superconductor KOs2O6 with Tc = 9.6 K is investigated by measuring magnetic torque. A large anisotropy of magnetic torque is observed in the superconducting state below Tp = 7.6 K, where a first-order structural transition takes place, in spite of the inherent isotropic nature of the structural and electronic properties. Magnetic torque is enhanced at external magnetic fields parallel to the [1 1 1] and [0 0 1] directions. Moreover, a pronounced peak effect is also observed in the magnetic field dependence of the torque in these two directions. We consider that the observed anisotropy is related to a microstructure associated with the structural transition.
Analysis of three idealized reactor configurations: plate, pin, and homogeneous
International Nuclear Information System (INIS)
McKnight, R.D.
1983-01-01
Detailed Monte Carlo calculations have been performed for three distinct configurations of an idealized fast critical assembly. This idealized assembly was based on the LMFBR benchmark critical assembly ZPR-6/7. In the first configuration, the entire core was loaded with the plate unit cell of ZPR-6/7. In the second configuration, the entire core was loaded with the ZPR sodium-filled pin calandria. The actual ZPR pin calandria are loaded with mixed (U,Pu) oxide pins which closely match the composition of the ZPR-6/7 plate unit cell. For the present study, slight adjustments were made in the atom concentrations and the length of the pin calandria in order to make the core boundaries and average composition for the pin-cell configuration identical to those of the plate-cell configuration. In the third configuration, the core was homogeneous, again with identical core boundaries and average composition as the plate and pin configurations
Improved pinning regime by energetic ions using reduction of pinning potential
Energy Technology Data Exchange (ETDEWEB)
Weinstein, Roy; Gandini, Alberto; Sawh, Ravi-Persad; Parks, Drew; Mayes, Bill
2003-05-15
When ion damage is used to create pinning centers, full columnar pinning centers provide the largest pinning potential, U{sub pin}, but not the greatest J{sub c} or pinned field, B{sub pin}. Some of the characteristics of columnar defects which limit J{sub c} and B{sub pin} are discussed, including reduction of percolation path, and the need for a larger number of columns of damage, for pinning, than are usually estimated. It is concluded that columnar pinning centers are limited to B{sub pin}<4 T, and also severely reduce J{sub c}. Evidence is reviewed that aligned damage, or broken-columnar pinning centers, described herein, can provide orders of magnitude higher J{sub c}, and higher pinned field, despite providing lower U{sub pin}. A pinning center morphology is discussed which utilizes multiple-in-line-damage (MILD). For, e.g., present day large grain HTS J{sub c}, obtainable by MILD pinning, is estimated to be of the order of 10{sup 6} A/cm{sup 2} at 77 K, even when crystal plane alignment and weak links are not improved. Pinned field is increased by over an order of magnitude. An experiment is proposed to confirm these observations, and to directly compare MILD to columnar pinning centers. It will also determine the optimum MILD structure. Other measurements of interest, made possible by the same data set, are described.
Fuel canister and blockage pin fabrication for SLSF Experiment P4
International Nuclear Information System (INIS)
Rhude, H.V.; Folkrod, J.R.; Noland, R.A.; Schaus, P.S.; Benecke, M.W.; Delucchi, T.A.
1983-01-01
As part of its fast breeder reactor safety research program, Argonne National Laboratory (ANL) has conducted an experiment (SLSF Experiment P4) to determine the extent of fuel-failure propagation resulting from the release of molten fuel from one or more heat-generating fuel canisters. The test conditions consisted of 37 full-length FTR fuel pins operating at FTR rated core nominal peak fuel/reduced coolant conditions. Thirty-four of the the fuel pins were prototypical FTR mixed-oxide fuel pins. The other three fuel pins were fabricated with a mid-core section having an enlarged canister containing fully enriched UO 2 . Two of the canisters were cylindrical and one was fluted. The cylindrical canisters were designed to fail and release molten fuel into the 37-pin fuel cluster at near full power
Results of transient overpower events on breached and unbreached fuel pins
International Nuclear Information System (INIS)
Strain, R.V.; Tsai, H.C.; Neimark, L.A.; Aratani, K.
1986-04-01
The objective of the extended overpower tests on intact pins was to determine the pin cladding breaching thresholds vis-a-vis the Plant Protection System (PPS) trip settings, typically at ∼10 to 15% overpower. These tests emphasize slow operational-type transients in light of earlier work which suggested that irradiated mixed-oxide fuel pins may be particularly vulnerable in the slow ramp-rate regime. An overview of the extended overpower test series was previously reported. More recent results on two of the tests in this series are included in this paper. These two tests, designated TOPI-1A and TOPI-1B, were each conducted on a 19-pin assembly with various pin design, operation and burnup variables. The overpower ramp rates for the TOPI-1A and -1B tests were 0.1%/s and 10%/s, respectively
The silicon-silicon oxide multilayers utilization as intrinsic layer on pin solar cells
International Nuclear Information System (INIS)
Colder, H.; Marie, P.; Gourbilleau, F.
2008-01-01
Silicon nanostructures are promising candidate for the intrinsic layer on pin solar cells. In this work we report on new material: silicon-rich silicon oxide (SRSO) deposited by reactive magnetron sputtering of a pure silica target and an interesting structure: multilayers consisting of a stack of SRSO and pure silicon oxide layers. Two thicknesses of the SRSO sublayer, t SRSO , are studied 3 nm and 5 nm whereas the thickness of silica sublayer is maintaining at 3 nm. The presence of nanocrystallites of silicon, evidenced by X-Ray diffraction (XRD), leads to photoluminescence (PL) emission at room temperature due to the quantum confinement of the carriers. The PL peak shifts from 1.3 eV to 1.5 eV is correlated to the decreasing of t SRSO from 5 nm down to 3 nm. In the purpose of their potential utilization for i-layer, the optical properties are studied by absorption spectroscopy. The achievement a such structures at promising absorption properties. Moreover by favouring the carriers injection by the tunnel effect between silicon nanograins and silica sublayers, the multilayers seem to be interesting for solar cells
Analisis Statistika dengan SPSS
Mustari, Kahar
2012-01-01
Buku ini membahas tentang berbagai model analisis statistika yang dapat digunakan dalam berbagai bidang penelitian. Pembahasan buku ini dilengkapi pula dengan penerapan analisis statistika yang menggunakan program SPSS versi 20 sehingga memudahkan pembaca untuk menerapkannya. Oleh karena itu, buku ini penting dibaca oleh mahasiswa atau peneliti yang melakukan pengolahan data penelitian.
PENERAPAN ANALISIS SWOC DALAM RENCANA STRATEGIS PENDIDIKAN
Directory of Open Access Journals (Sweden)
Hardianto -
2018-01-01
Full Text Available Analisis SWOC merupakan salah satu langkah yang bisa diambil dalam membuat sebuah rencana strategis pendidikan. Analisis ini dilakukan untuk melihat secara mendalam situasi internal dan eksternal organisasi. Situasi internal yang dilihat adalah kekuatan (Strenghts dan kelemahan (Weaknesses organisasi pendidikan. Situasi eksternal berupa peluang (Opportinities dan tantangan (Challenges. Untuk membuat sebuah rencana strategis yang baik dapat dilakukan dengan menganalisis setiap kekuatan, kelemahan, peluang dan tantangan. Teknik kartu salju (snow card bisa digunakan dalam melakukan analisis SWOC. Hasil analisis tersebut nantinya akan melahirkan kombinasi strategi kekuatan-peluang, kekuatan-tantangan, kelemahan-peluang dan kelemahan-tantangan.
Heterogeneous neutron-leakage model for PWR pin-by-pin calculation
International Nuclear Information System (INIS)
Li, Yunzhao; Zhang, Bin; Wu, Hongchun; Shen, Wei
2017-01-01
Highlights: •The derivation of the formula of the leakage model is introduced. This paper evaluates homogeneous and heterogeneous leakage models used in PWR pin-by-pin calculation. •The implements of homogeneous and heterogeneous leakage models used in pin-cell homogenization of the lattice calculation are studied. A consistent method of cooperation between the heterogeneous leakage model and the pin-cell homogenization theory is proposed. •Considering the computational cost, a new buckling search scheme is proposed to reach the convergence faster. The computational cost of the newly proposed neutron balance scheme is much less than the power-method scheme and the linear-interpolation scheme. -- Abstract: When assembly calculation is performed with the reflective boundary condition, a leakage model is usually required in the lattice code. The previous studies show that the homogeneous leakage model works effectively for the assembly homogenization. However, it becomes different and unsettled for the pin-cell homogenization. Thus, this paper evaluates homogeneous and heterogeneous leakage models used in pin-by-pin calculation. The implements of homogeneous and heterogeneous leakage models used in pin-cell homogenization of the lattice calculation are studied. A consistent method of cooperation between the heterogeneous leakage model and the pin-cell homogenization theory is proposed. Considering the computational cost, a new buckling search scheme is proposed to reach the convergence faster. For practical reactor-core applications, the diffusion coefficients determined by the transport cross-section or by the leakage model are compared with each other to determine which one is more accurate for the Pressurized Water Reactor pin-by-pin calculation. Numerical results have demonstrated that the heterogeneous leakage model together with the diffusion coefficient determined by the heterogeneous leakage model would have the higher accuracy. The new buckling search
Binder free MnO2/PIn electrode material for supercapacitor application
Purty, B.; Choudhary, R. B.; Kandulna, R.; Singh, R.
2018-05-01
Electrochemically stable MnO2/PIn nanocomposite was synthesized via in-situ chemical oxidative polymerization process. The structural and morphological properties were studied through FTIR and FESEM characterizing techniques. Sphere like PIn and MnO2 nanorods offers interacting surface for charge transfer action. The electrochemical properties were investigated through cyclic voltammetry (CV), galvanostatic charge-discharge (GCD) and electrochemical impedance spectroscopic (EIS) techniques. The significant enhancement in capacitance value with 95% coulombic efficiency and relatively low equivalent series resistance (ESR)˜0.4 Ω proved that MnO2/PIn nanocomposite is an excellent performer as an electrode material in the spectrum of supercapcitors and optoelectronic devices.
Unicortical self-drilling external fixator pins reduce thermal effects during pin insertion.
Greinwald, Markus; Varady, Patrick A; Augat, Peter
2017-12-14
External fixation is associated with the risk of pin loosening and pin infection potentially associated to thermal bone necrosis during pin insertion. This study aims to investigate if the use of external fixator systems with unicortical pins reduces the heat production during pin insertion compared to fixators with bicortical pins. Porcine bone specimens were employed to determine bone temperatures during insertion of fixator pins. Two thermographic cameras were used for a simultaneous temperature measurement on the bone surface (top view) and a bone cross-section (front view). Self-drilling unicortical and bicortical pins were inserted at different rotational speeds: (30-600) rpm. Maximum and mean temperatures of the emerging bone debris, bone surface and bone cross-section were analyzed. Maximum temperatures of up to 77 ± 26 °C were measured during pin insertion in the emerging debris and up to 42 ± 2 °C on the bone surface. Temperatures of the emerging debris increased with increasing rotational speeds. Bicortical pin insertion generated significantly higher temperatures at low insertion speed (30 rpm) CONCLUSION: The insertion of external fixator pins can generate a considerable amount of heat around the pins, primarily emerging from bone debris and at higher insertion speeds. Our findings suggest that unicortical, self-drilling fixator pins have a decreased risk for thermal damage, both to the surrounding tissue and to the bone itself.
International Nuclear Information System (INIS)
Smolen, G.R.; Funabashi, H.
1987-01-01
Critical experiments have been conducted with organically moderated mixed-oxide (MOX) fuel pin assemblies at the Pacific Northwest Lab. Critical Mass Lab. These experiments are part of a joint exchange program between the US Dept. of Energy and the Power Reactor and Nuclear Fuel Development Corp. of Japan in the area of criticality data development. The purpose of these experiments is to benchmark computer codes and cross-section libraries and to assess the reactivity difference between systems moderated by water and those moderated by an organic solution. Past studies have indicated that some organic mixtures may be better moderators than water. This topic is of particular importance to the criticality safety of fuel processing plants where fissile material is dissolved in organic solutions during the solvent extraction process. In the past, it has been assumed that the codes and libraries benchmarked with water-moderated experiments were adequate when performing design and licensing studies of organically moderated systems. Calculations presented in this paper indicated that the Scale code system and the 27-energy-group cross-section library accurately compute k/sub eff/ for organically moderated MOX fuel pin assemblies. Furthermore, the reactivity of an organic solution with a 32 vol % TBP/68 vol% NPH mixture in a heterogeneous configuration is the same, for practical purposes, as water
International Nuclear Information System (INIS)
Smolen, G.R.
1987-01-01
Critical experiments have been conducted with organic-moderated mixed oxide (MOX) fuel pin assemblies at the Pacific Northwest Laboratory (PNL) Critical Mass Laboratory (CML). These experiments are part of a joint exchange program between the United States Department of Energy (USDOE) and the Power Reactor and Nuclear Fuel Development Corporation (PNC) of Japan in the area of criticality data development. The purpose of these experiments is to benchmark computer codes and cross-section libraries and to assess the reactivity difference between systems moderated by water and those moderated by an organic solution. Past studies have indicated that some organic mixtures may be better moderators than water. This topic is of particular importance to the criticality safety of fuel processing plants where fissile material is dissolved in organic solutions during the solvent extraction process. In the past, it has been assumed that the codes and libraries benchmarked with water-moderated experiments were adequate when performing design and licensing studies of organic-moderated systems. Calculations presented in this paper indicated that the SCALE code system and the 27-energy-group cross-section accurately compute k-effectives for organic moderated MOX fuel-pin assemblies. Furthermore, the reactivity of an organic solution with a 32-vol-% TBP/68-vol-% NPH mixture in a heterogeneous configuration is the same, for practical purposes, as water. 5 refs
Reduction of halo pin site morbidity with a new pin care regimen.
Kazi, Hussain Anthony; de Matas, Marcus; Pillay, Robin
2013-06-01
A retrospective analysis of halo device associated morbidity over a 4-year period. To assess the impact of a new pin care regimen on halo pin site related morbidity. Halo orthosis treatment still has a role in cervical spine pathology, despite increasing possibilities of open surgical treatment. Published figures for pin site infection range from 12% to 22% with pin loosening from 7% to 50%. We assessed the outcome of a new pin care regimen on morbidity associated with halo spinal orthoses, using a retrospective cohort study from 2001 to 2004. In the last two years, our pin care regimen was changed. This involved pin site care using chlorhexidene & regular torque checking as part of a standard protocol. Previously, povidone iodine was used as skin preparation in theatre, followed by regular sterile saline cleansing when pin sites became encrusted with blood. There were 37 patients in the series, the median age was 49 (range, 22-83) and 20 patients were male. The overall infection rate prior to the new pin care protocol was 30% (n=6) and after the introduction, it dropped to 5.9% (n=1). This difference was statistically significant (p<0.05). Pin loosening occurred in one patient in the group prior to the formal pin care protocol (3%) and none thereafter. Reduced morbidity from halo use can be achieved with a modified pin cleansing and tightening regimen.
Flux pinning by voids in surface-oxidized superconducting niobium and vanadium
International Nuclear Information System (INIS)
Meij, G.P. van der.
1984-01-01
This thesis describes a study of flux pinning by small voids (roughly 10 nm) in the type II superconductors niobium and vanadium. These voids were created in rectangular foils (with typical dimensions of 30x3x0.2 mm) during an irradiation with fast neutrons in the High Flux Reactor at Petten at temperatures between 400 and 1000 0 C. The pinning force per unit volume is determined from the magnetic properties of the superconducting samples. The experiments were carried out in a slowly ramped magnetic field, as well as in a combination of a static and a much smaller alternating field. (Auth.)
Corrosion of Ti6Al4V pins produced by direct metal laser sintering
Energy Technology Data Exchange (ETDEWEB)
Damborenea, J.J. de, E-mail: jdambo@cenim.csic.es [Centro Nacional de Investigaciones Metalúrgicas (CENIM-CSIC), Avenida Gregorio del Amo, 8, E-28040 Madrid (Spain); Arenas, M.A. [Centro Nacional de Investigaciones Metalúrgicas (CENIM-CSIC), Avenida Gregorio del Amo, 8, E-28040 Madrid (Spain); Larosa, Maria Aparecida; Jardini, André Luiz [National Institute of Biofabrication (INCT-BIOFABRIS), State of University of Campinas (UNICAMP), Campinas (Brazil); School of Chemical Engineering, State of University of Campinas (UNICAMP), Campinas (Brazil); Carvalho Zavaglia, Cecília Amélia de [National Institute of Biofabrication (INCT-BIOFABRIS), State of University of Campinas (UNICAMP), Campinas (Brazil); Faculty of Mechanical Engineering, State of University of Campinas (UNICAMP), Campinas (Brazil); Conde, A. [Centro Nacional de Investigaciones Metalúrgicas (CENIM-CSIC), Avenida Gregorio del Amo, 8, E-28040 Madrid (Spain)
2017-01-30
Highlights: • Pins of Ti6Al4V have been produced by DMLS technique. • Corrosion behavior of pins is similar to Ti6Al4V commercial Kirschner wires. • Formation of voluminous white oxide can appear at potentials higher than 2.4 V. • Defects originated during processing may cause this unusual behavior. - Abstract: Direct Metal Laser Sintering (DMLS) technique allows the manufacturing a wide variety of medical devices for any type of prosthetic surgery (HIP, dental, cranial, maxillofacial) as well as for internal fixation devices (K-Wires or Steinmann Pins). There are a large number of research studies on DMLS, including microstructural characterization, mechanical properties and those based on production quality assurance but the influence of porosity in the corrosion behavior of these materials not been sufficiently considered. In the present paper, surgical pins of Ti6Al4V have been produced by DMLS. After testing in a phosphate buffered saline solution, the surface of the titanium alloy appeared locally covered by a voluminous white oxide. This unexpected behavior was presumably due to the existence of internal defects in the pins as result of the manufacturing process. The importance of these defects—that might act as crevice nucleation sites- has been revealed by electrochemical techniques and confirmed by computed tomography.
Corrosion of Ti6Al4V pins produced by direct metal laser sintering
International Nuclear Information System (INIS)
Damborenea, J.J. de; Arenas, M.A.; Larosa, Maria Aparecida; Jardini, André Luiz; Carvalho Zavaglia, Cecília Amélia de; Conde, A.
2017-01-01
Highlights: • Pins of Ti6Al4V have been produced by DMLS technique. • Corrosion behavior of pins is similar to Ti6Al4V commercial Kirschner wires. • Formation of voluminous white oxide can appear at potentials higher than 2.4 V. • Defects originated during processing may cause this unusual behavior. - Abstract: Direct Metal Laser Sintering (DMLS) technique allows the manufacturing a wide variety of medical devices for any type of prosthetic surgery (HIP, dental, cranial, maxillofacial) as well as for internal fixation devices (K-Wires or Steinmann Pins). There are a large number of research studies on DMLS, including microstructural characterization, mechanical properties and those based on production quality assurance but the influence of porosity in the corrosion behavior of these materials not been sufficiently considered. In the present paper, surgical pins of Ti6Al4V have been produced by DMLS. After testing in a phosphate buffered saline solution, the surface of the titanium alloy appeared locally covered by a voluminous white oxide. This unexpected behavior was presumably due to the existence of internal defects in the pins as result of the manufacturing process. The importance of these defects—that might act as crevice nucleation sites- has been revealed by electrochemical techniques and confirmed by computed tomography.
Energy Technology Data Exchange (ETDEWEB)
Dobrynin, D; Friedman, G [Electrical and Computer Engineering Department, College of Engineering, Drexel University, Philadelphia, PA (United States); Arjunan, K; Clyne, A Morss [School of Biomedical Engineering, Science and Health Systems, Drexel University, Philadelphia, PA (United States); Fridman, A, E-mail: alisam@coe.drexel.edu [Department of Mechanical Engineering and Mechanics, College of Engineering, Drexel University, Philadelphia, PA (United States)
2011-02-23
Nitric oxide has great potential for improving wound healing through both inflammatory and vascularization processes. Nitric oxide can be produced in high concentrations by atmospheric pressure thermal plasmas. We measured the physical characteristics and nitric oxide production of a pin-to-hole spark discharge (PHD) plasma, as well as plasma-produced nitric oxide delivery into liquid and endothelial cells. The plasma temperature was calculated as 9030 {+-} 320 K by the Boltzmann method, which was adequate to produce nitric oxide, although the average gas temperature was near room temperature. The plasma produced significant UV radiation and hydrogen peroxide, but these were prevented from reaching the cells by adding a straight or curved tube extension to the plasma device. Plasma-produced nitric oxide in gas reached 2000 ppm and rapidly diffused into liquid and cells. Cells remained viable following plasma treatment and showed a linear increase in cGMP concentration with plasma treatment, indicating an intracellular functional response to PHD plasma NO. These data suggest that this plasma may provide a novel method for delivering NO locally and directly for enhanced wound healing.
International Nuclear Information System (INIS)
Dobrynin, D; Friedman, G; Arjunan, K; Clyne, A Morss; Fridman, A
2011-01-01
Nitric oxide has great potential for improving wound healing through both inflammatory and vascularization processes. Nitric oxide can be produced in high concentrations by atmospheric pressure thermal plasmas. We measured the physical characteristics and nitric oxide production of a pin-to-hole spark discharge (PHD) plasma, as well as plasma-produced nitric oxide delivery into liquid and endothelial cells. The plasma temperature was calculated as 9030 ± 320 K by the Boltzmann method, which was adequate to produce nitric oxide, although the average gas temperature was near room temperature. The plasma produced significant UV radiation and hydrogen peroxide, but these were prevented from reaching the cells by adding a straight or curved tube extension to the plasma device. Plasma-produced nitric oxide in gas reached 2000 ppm and rapidly diffused into liquid and cells. Cells remained viable following plasma treatment and showed a linear increase in cGMP concentration with plasma treatment, indicating an intracellular functional response to PHD plasma NO. These data suggest that this plasma may provide a novel method for delivering NO locally and directly for enhanced wound healing.
Combs, Kristen; Frick, Steven; Kiebzak, Gary
2016-12-03
Pediatric supracondylar humerus fractures are the most common elbow fractures in pediatric patients. Surgical fixation using pins is the primary treatment for displaced fractures. Pin site infections may follow supracondylar humerus fracture fixation; the previously reported incidence rate in the literature is 2.34%, but there is significant variability in reported incidence rates of pin site infection. This study aims to define the incidence rate and determine pre-, peri-, and postoperative factors that may contribute to pin site infection following operative reduction, pinning, and casting. A retrospective chart analysis was performed over a one-year period on patients that developed pin site infection. A cast care form was added to Nemours' electronic medical records (EMR) system (Epic Systems Corp., Verona, WI) to identify pin site infections for retrospective review. The cast care form noted any inflamed or infected pins. Patients with inflamed or infected pin sites underwent a detailed chart review. Preoperative antibiotic use, number and size of pins used, method of postoperative immobilization, pin dressings, whether postoperative immobilization was changed prior to pin removal, and length of time pins were in place was recorded. A total of 369 patients underwent operative reduction, pinning, and casting. Three patients developed a pin site infection. The pin site infection incidence rate was 3/369=0.81%. Descriptive statistics were reported for the three patients that developed pin site infections and three patients that developed pin site complications. Pin site infection development is low. Factors that may contribute to the development of pin site infection include preoperative antibiotic use, length of time pins are left in, and changing the cast prior to pin removal.
Computer simulation of vortex pinning in type II superconductors. II. Random point pins
International Nuclear Information System (INIS)
Brandt, E.H.
1983-01-01
Pinning of vortices in a type II superconductor by randomly positioned identical point pins is simulated using the two-dimensional method described in a previous paper (Part I). The system is characterized by the vortex and pin numbers (N/sub v/, N/sub p/), the vortex and pin interaction ranges (R/sub v/, R/sub p/), and the amplitude of the pin potential A/sub p/. The computation is performed for many cases: dilute or dense, sharp or soft, attractive or repulsive, weak or strong pins, and ideal or amorphous vortex lattice. The total pinning force F as a function of the mean vortex displacment X increases first linearly (over a distance usually much smaller than the vortex spacing and than R/sub p/) and then saturates, fluctuating about its averaging F-bar. We interpret F-bar as the maximum pinning force j/sub c/B of a large specimen. For weak pins the prediction of Larkin and Ovchinnikov for two-dimensional collective pinning is confirmed: F-bar = const. iW/R/sub p/c 66 , where W-bar is the mean square pinning force and c 66 is the shear modulus of the vortex lattice. If the initial vortex lattice is chosen highly defective (''amorphous'') the constant is 1.3--3 times larger than for the ideal triangular lattice. This finding may explain the often observed ''history effect.'' The function F-bar(A/sub p/) exhibits a jump, which for dilute, sharp, attractive pins occurs close to the ''threshold value'' predicted for isolated pins by Labusch. This jump reflects the onset of plastic deformation of the vortex lattice, and in some cases of vortex trapping, but is not a genuine threshold
A macroscopic cross-section model for BWR pin-by-pin core analysis
International Nuclear Information System (INIS)
Fujita, Tatsuya; Endo, Tomohiro; Yamamoto, Akio
2014-01-01
A macroscopic cross-section model used in boiling water reactor (BWR) pin-by-pin core analysis is studied. In the pin-by-pin core calculation method, pin-cell averaged cross sections are calculated for many combinations of core state and depletion history variables and are tabulated prior to core calculations. Variations of cross sections in a core simulator are caused by two different phenomena (i.e. instantaneous and history effects). We treat them through the core state variables and the exposure-averaged core state variables, respectively. Furthermore, the cross-term effect among the core state and the depletion history variables is considered. In order to confirm the calculation accuracy and discuss the treatment of the cross-term effect, the k-infinity and the pin-by-pin fission rate distributions in a single fuel assembly geometry are compared. Some cross-term effects could be negligible since the impacts of them are sufficiently small. However, the cross-term effects among the control rod history (or the void history) and other variables have large impacts; thus, the consideration of them is crucial. The present macroscopic cross-section model, which considers such dominant cross-term effects, well reproduces the reference results and can be a candidate in practical applications for BWR pin-by-pin core analysis on the normal operations. (author)
Physics evaluation for testino. of RAPS and TAPS fuel pins in CIRUS pressurised water loop
International Nuclear Information System (INIS)
John, Benjamin; Paul, O.P.K.
1976-01-01
Relevant calculations carried out to assess the reactivity effect, heat generation and other parameters for testing of RAPS and TAPS fuel pins in the Cirus pressurised water loop are summarised. The Cirus neutron flux level being low, in order to simulate the RAPS design heat rating of ∫ Kdtheta = 40 w/cm, the required plutonium enrichment in mixed plutonium uranium oxide fuel pin was worked out. The results showed that a PuO 2 enrichment of 1.5 wt percent would be necessary to meet the above requirement. The analysis for the TAPS pin indicated that the desired heat flux of 115w/cm 2 cannot be obtained in the Cirus loop with either a 7 pin cluster geometry, or with a single pin with the enrichment level as used in TAPS pin. Lattice code DUMLAC and the core simulation code AECLHEX were used for these studies. (author)
Development of a fast pin-by-pin transport solver in ARCADIA registered
International Nuclear Information System (INIS)
Geemert, R. van
2009-01-01
For satisfaction of future global customer needs, dedicated efforts are being coordinated internationally and pursued continuously at AREVA NP. The currently ongoing CONVERGENCE project is committed to the development of the ARCADIA registered next generation core simulation software package. ARCADIA registered will be put to global use by all AREVA NP business regions, for the entire spectrum of core design processes, licensing computations and safety studies. As part of the currently ongoing trend towards more sophisticated neutronics methodologies, an SP 3 nodal transport concept (van Geemert 2008) has been developed for ARTEMIS (Hobson 2008) which is the steady-state and transient core simulation part of ARCADIA registered . For enabling a high computational performance, the SP 3 calculations are accelerated by applying multi-level coarse mesh rebalancing (van Geemert 2006). In the current implementation, SP 3 is typically about 1.4 times as expensive computationally as SP 1 (diffusion). The developed SP 3 solution concept is foreseen as the future computational workhorse for many-group 3D pin-by-pin full core computations by ARCADIA registered . With the entire numerical workload being highly parallelizable through domain decomposition techniques, associated CPU-time requirements that adhere to the efficiency needs in the nuclear industry can be expected to become feasible in the near future. The accuracy enhancement obtainable by using SP 3 instead of SP 1 has been verified by a detailed comparison of ARTEMIS 16-group pin-by-pin SP N results with KAERI's DeCart reference results (Kozlowski 2003) for the 2D pin-by-pin Purdue UO 2 /MOX benchmark. Within the associated pin-by-pin grid, large pin-to-pin variations in cross-section values occur due to the explicit modelling of guide tubes, gadolinium pins as well as the heterogeneous distribution of MOX assemblies and UO 2 assemblies featuring significantly different burnups. With a pin-by-pin grid as
SIFAIL: a subprogram to calculate cladding deformation and damage for fast reactor fuel pins
International Nuclear Information System (INIS)
Wilson, D.R.; Dutt, D.S.
1979-05-01
SIFAIL is a series of subroutines used in conjunction with the thermal performance models of SIEX to assist in the evaluation of mechanical performance of mixed uranium plutonium oxide fuel pins. Cladding deformations due to swelling and creep are calculated. These have been compared to post-irradiation data from fuel pin tests in EBR-II. Several fuel pin cladding failure criteria (cumulative damage, total strain, and thermal creep strain) are evaluated to provide the fuel pin designer with a basis to select design parameters. SIFAIL allows the user many property options for cladding material. Code input is limited to geometric and environmental parameters, with a consistent set of material properties provided by the code. The simplified, yet adequate, thin wall stress--strain calculations provide a reliable estimate of fuel pin mechanical performance, while requiring a small amount of core storage and computer running time
International Nuclear Information System (INIS)
Inoue, Masaki; Ukai, Shigeharu; Asaga, Takeo
1999-08-01
The effects of fabrication parameters, irradiation conditions and fuel microstructural feature on fuel pellet relocation behavior in fast reactor fuel pins were investigated. This work focused only on beginning-of-life conditions, when fuel centerline temperature depends largely on the behavior. Fuel pellet relocation behavior in Joyo Mk-II driver could not be characterized because of the lack of data. And the behavior in FFTF driver and its larger diameter type fuel pins could not be characterized because of the extensive lot-by-lot scatters. The behavior both in Monju type and in Joyo power-to-melt type fuel pins were similar to each other, and depends largely on the as-fabricated gap width while the effects of linear heat rate and the extent of microstructural evolution were negligible. And fuel pellet centerline melting seems to affect slightly the behavior. The correlation, which describes the extent of relocation both in Monju type and in Joyo power-to-melt type fuel pins, were newly formulated and extrapolated for Joyo Mk-II driver, FFTF driver and its larger diameter type fuel pins. And the behavior in Joyo Mk-II driver seemed to be similar. On the contrary, the similarity with JNC fuel pins was observed case-by-case in FFTF driver and its larger diameter type fuel pins. (author)
Transformation of Helicopter PinS Procedures for Airplanes
Directory of Open Access Journals (Sweden)
Jakub Kraus
2013-09-01
Full Text Available This article deals with the possibility to use existing helicopter Point in Space procedures with minor changes for airplanes. The basis is to find parts of PinS procedures that need to be changed, suggest these changes, and then determine whether the revised procedures could be usable and could bring the benefits for airplane operations.
Effects of variations in fuel pellet composition and size on mixed-oxide fuel pin performance
International Nuclear Information System (INIS)
Makenas, B.J.; Jensen, B.W.; Baker, R.B.
1980-10-01
Experiments have been conducted which assess the effects on fuel pin performance of specific minor variations from nominal in both fuel pellet size and pellet composition. Such pellets are generally referred to in the literature as rogue pellets. The effect of these rogue pellets on fuel pin and reactor performance is shown to be minimal
PINS Spectrum Identification Guide
Energy Technology Data Exchange (ETDEWEB)
A.J. Caffrey
2012-03-01
The Portable Isotopic Neutron Spectroscopy—PINS, for short—system identifies the chemicals inside munitions and containers without opening them, a decided safety advantage if the fill chemical is a hazardous substance like a chemical warfare agent or an explosive. The PINS Spectrum Identification Guide is intended as a reference for technical professionals responsible for the interpretation of PINS gamma-ray spectra. The guide is divided into two parts. The three chapters that constitute Part I cover the science and technology of PINS. Neutron activation analysis is the focus of Chapter 1. Chapter 2 explores PINS hardware, software, and related operational issues. Gamma-ray spectral analysis basics are introduced in Chapter 3. The six chapters of Part II cover the identification of PINS spectra in detail. Like the PINS decision tree logic, these chapters are organized by chemical element: phosphorus-based chemicals, chlorine-based chemicals, etc. These descriptions of hazardous, toxic, and/or explosive chemicals conclude with a chapter on the identification of the inert chemicals, e.g. sand, used to fill practice munitions.
International Nuclear Information System (INIS)
Languille, A.
1979-07-01
The Phenix reactor has operated for 4 years in a satisfactory manner. The first 2 sub-assembly loadings contained pins clad in solution treated 316. The principal pin strains are: diametral strain (swelling and irradiation creep), ovality and spiral bending of the pin (interaction of wire and pin cluster and wrapper). A pin cluster irradiated to a dose of 80 dpa F reached a pin diameter strain of 5%. This strain is principally due to swelling (low fission gas pressure). The principal parameters governing the swelling are instantaneous dose, time and temperature for a given type of pin cladding. Other types of steel are or will be irradiated in Phenix. In particular, cold-worked titanium stabilised 316 steel should contribute towards a reduction in the pin clad strains and increase the target burn-up in this reactor. (author)
... Drugs & Supplements Videos & Tools Español You Are Here: Home → Medical Encyclopedia → Pin care URL of this page: //medlineplus.gov/ency/patientinstructions/000481.htm Pin care To use the sharing features on this page, please enable JavaScript. Broken bones can be fixed in surgery with metal ...
Quasi-hexagonal vortex-pinning lattice using anodized aluminum oxide nanotemplates
DEFF Research Database (Denmark)
Hallet, X.; Mátéfi-Tempfli, M.; Michotte, S.
2009-01-01
The bottom barrier layer of well-ordered nanoporous alumina membranes reveals a previously unexploited nanostructured template surface consisting of a triangular lattice of hemispherical nanoscale bumps. Quasi-hexagonal vortex-pinning lattice arrays are created in superconducting Nb films deposited...... onto this template (see image). Matching effects are preserved at higher magnetic fields and lower temperatures when compared to holes on the top face....
Genome-wide identification and evolution of the PIN-FORMED (PIN) gene family in Glycine max.
Liu, Yuan; Wei, Haichao
2017-07-01
Soybean (Glycine max) is one of the most important crop plants. Wild and cultivated soybean varieties have significant differences worth further investigation, such as plant morphology, seed size, and seed coat development; these characters may be related to auxin biology. The PIN gene family encodes essential transport proteins in cell-to-cell auxin transport, but little research on soybean PIN genes (GmPIN genes) has been done, especially with respect to the evolution and differences between wild and cultivated soybean. In this study, we retrieved 23 GmPIN genes from the latest updated G. max genome database; six GmPIN protein sequences were changed compared with the previous database. Based on the Plant Genome Duplication Database, 18 GmPIN genes have been involved in segment duplication. Three pairs of GmPIN genes arose after the second soybean genome duplication, and six occurred after the first genome duplication. The duplicated GmPIN genes retained similar expression patterns. All the duplicated GmPIN genes experienced purifying selection (K a /K s genome sequence of 17 wild and 14 cultivated soybean varieties. Our research provides useful and comprehensive basic information for understanding GmPIN genes.
International Nuclear Information System (INIS)
Gras, Ch.; Stanley, S.J.
2008-01-01
The paper presents some interesting aspects associated with X-ray imaging and its potential application in the nuclear industry. The feasibility of using X-ray technology for the post-irradiation examination of a fuel pin has been explored, more specifically pin metrology and carbon deposition measurement. The non-active sample was specially designed to mimic the structure of an AGR fuel pin whilst a carbon based material was applied to the mock up fuel rod in order to mimic carbon deposition. Short duration low energy (50 kV) 2D digital radiography was employed and provided encouraging results (with respect to carbon deposition thickness and structure measurements) for the mock up fuel pin with a spatial resolution of around 10 μm. Obtaining quantitative data from the resultant images is the principal added value associated with X-ray imaging. A higher intensity X-ray beam (≥90 kV) was also used in conjunction with the low energy set-up to produce a clear picture of the cladding as well as the interface between the lead (Pb mimics the uranium oxide) and stainless steel cladding. Spent fuel metrology and routine radiography are two additional tasks that X-ray imaging could perform for the post-irradiation examination programme. Therefore, when compared to other techniques developed to deliver information on one particular parameter, X-ray imaging offers the possibility to extract useful information on a range of parameters
Peptidyl-prolyl cis/trans-isomerase A1 (Pin1) is a target for modification by lipid electrophiles.
Aluise, Christopher D; Rose, Kristie; Boiani, Mariana; Reyzer, Michelle L; Manna, Joseph D; Tallman, Keri; Porter, Ned A; Marnett, Lawrence J
2013-02-18
Oxidation of membrane phospholipids is associated with inflammation, neurodegenerative disease, and cancer. Oxyradical damage to phospholipids results in the production of reactive aldehydes that adduct proteins and modulate their function. 4-Hydroxynonenal (HNE), a common product of oxidative damage to lipids, adducts proteins at exposed Cys, His, or Lys residues. Here, we demonstrate that peptidyl-prolyl cis/trans-isomerase A1 (Pin1), an enzyme that catalyzes the conversion of the peptide bond of pSer/pThr-Pro moieties in signaling proteins from cis to trans, is highly susceptible to HNE modification. Incubation of purified Pin1 with HNE followed by MALDI-TOF/TOF mass spectrometry resulted in detection of Michael adducts at the active site residues His-157 and Cys-113. Time and concentration dependencies indicate that Cys-113 is the primary site of HNE modification. Pin1 was adducted in MDA-MB-231 breast cancer cells treated with 8-alkynyl-HNE as judged by click chemistry conjugation with biotin followed by streptavidin-based pulldown and Western blotting with anti-Pin1 antibody. Furthermore, orbitrap MS data support the adduction of Cys-113 in the Pin1 active site upon HNE treatment of MDA-MB-231 cells. siRNA knockdown of Pin1 in MDA-MB-231 cells partially protected the cells from HNE-induced toxicity. Recent studies indicate that Pin1 is an important molecular target for the chemopreventive effects of green tea polyphenols. The present study establishes that it is also a target for electrophilic modification by products of lipid peroxidation.
Design of unique pins for irradiation of higher actinides in a fast reactor
International Nuclear Information System (INIS)
Basmajian, J.A.; Birney, K.R.; Weber, E.T.; Adair, H.L.; Quinby, T.C.; Raman, S.; Butler, J.K.; Bateman, B.C.; Swanson, K.M.
1982-03-01
The actinides produced by transmutation reactions in nuclear reactor fuels are a significant factor in nuclear fuel burnup, transportation and reprocessing. Irradiation testing is a primary source of data of this type. A segmented pin design was developed which provides for incorporation of multiple specimens of actinide oxides for irradiation in the UK's Prototype Fast Reactor (PFR) at Dounreay Scotland. Results from irradiation of these pins will extend the basic neutronic and material irradiation behavior data for key actinide isotopes
Performance of refractory alloy-clad fuel pins
International Nuclear Information System (INIS)
Dutt, D.S.; Cox, C.M.; Millhollen, M.K.
1984-12-01
This paper discusses objectives and basic design of two fuel-cladding tests being conducted in support of SP-100 technology development. Two of the current space nuclear power concepts use conventional pin type designs, where a coolant removes the heat from the core and transports it to an out-of-core energy conversion system. An extensive irradiation testing program was conducted in the 1950's and 1960's to develop fuel pins for space nuclear reactors. The program emphasized refractory metal clad uranium nitride (UN), uranium carbide (UC), uranium oxide (UO 2 ), and metal matrix fuels (UCZr and BeO-UO 2 ). Based on this earlier work, studies presented here show that UN and UO 2 fuels in conjunction with several refractory metal cladding materials demonstrated high potential for meeting space reactor requirements and that UC could serve as an alternative but higher risk fuel
Phosphorylation of conserved PIN motifs directs Arabidopsis PIN1 polarity and auxin transport
Huang, F.; Kemel Zago, M.; Abas, L.; van Marion, A.; Galván-Ampudia, C.S.; Offringa, R.
2010-01-01
Polar cell-to-cell transport of auxin by plasma membrane-localized PIN-FORMED (PIN) auxin efflux carriers generates auxin gradients that provide positional information for various plant developmental processes. The apical-basal polar localization of the PIN proteins that determines the direction of
Flux Pinning in Superconductors
Matsushita, Teruo
2007-01-01
The book covers the flux pinning mechanisms and properties and the electromagnetic phenomena caused by the flux pinning common for metallic, high-Tc and MgB2 superconductors. The condensation energy interaction known for normal precipitates or grain boundaries and the kinetic energy interaction proposed for artificial Nb pins in Nb-Ti, etc., are introduced for the pinning mechanism. Summation theories to derive the critical current density are discussed in detail. Irreversible magnetization and AC loss caused by the flux pinning are also discussed. The loss originally stems from the ohmic dissipation of normal electrons in the normal core driven by the electric field induced by the flux motion. The readers will learn why the resultant loss is of hysteresis type in spite of such mechanism. The influence of the flux pinning on the vortex phase diagram in high Tc superconductors is discussed, and the dependencies of the irreversibility field are also described on other quantities such as anisotropy of supercondu...
Applicability of the diffusion and simplified P3 theories for BWR pin-by-pin core analysis
International Nuclear Information System (INIS)
Tada, Kenichi; Yamamoto, Akio; Kitamura, Yasunori; Yamane, Yoshihiro; Watanabe, Masato; Noda, Hiroshi
2007-01-01
The pin-by-pin fine mesh core calculation method is considered as a candidate of next-generation core calculation method for BWR. In this study, the diffusion and the simplified P 3 (SP 3 ) theories are applied to the pin-by-pin core analysis of BWR. Performances of the diffusion and the SP 3 theories for cell-homogeneous pin-by-pin fine mesh BWR core analysis are evaluated through comparison with cell-heterogeneous detailed transport calculation by the method of characteristics (MOC). In this study, two-dimensional, 2x2 multi-assemblies geometry is used to compare the prediction accuracies of the diffusion and the SP 3 theories. The 2x2 multi- assemblies geometry consists of two types of 9x9 UO 2 assembly that have two different enrichment splittings. To mitigate the cell-homogenization error, the SPH method is applied for the pin-by-pin fine mesh calculation. The SPH method is a technique that reproduces a result of heterogeneous calculation by that of homogeneous calculation. The calculation results indicated that diffusion theory shows larger discrepancy than that of SP 3 theory on pin-wise fission rates. Furthermore, the accuracy of the diffusion theory would not be sufficient for the pin-by-pin fine mesh calculation. In contrast to the diffusion theory, the SP 3 theory shows much better accuracy on pin wise fission rates. Therefore, if the SP 3 theory is applied, the accuracy of the pin-by-pin fine mesh BWR core analysis will be higher and will be sufficient for production calculation. (author)
International Nuclear Information System (INIS)
Linde, A. van der; Letsch, A.C.; Hornsveld, E.M.
1978-11-01
A three-pins, zircaloy-4 clad, sphere-pac bundle was irradiated in a 280 0 C PWR loop in the HFR at Petten during 131 effective full power days to a bundle average burnup of 0.84 % FIMA. The pins contained a mixture of 61.5 w/o of 1050 μm (U,Pu) 0 2 spheres, 18.5 w/o of 115 μm UO 2 spheres and 20.0 w/o of 2 spheres. The as-fabricated smear density of the vibratory compacted mixture was 81-85 % T.D. The pressure of the pin filling gas was 1 bar helium for pin 306 and 25 bar helium for the pins 308 and 309. The cladding was zircaloy-4 tubing, stress relieved for 4 hours at 540 0 C, with an inner diameter of 9.30 mm and a wall thickness of 0.73 mm. Exposure of the pins in the loop started in the as-pickled, degreased surface condition. The pins operated at an average heat rating of 335 W/cm and at a peak rating of 620 W/cm. The end-of -life peak rating was 425 W/cm. Unfavourable water chemistry conditions of the coolant during the last weeks of the irradition, in particular low NH 3 concentrations resulting in low pH values, caused the deposition of heavy crud layers on the pin surfaces. This crud layer caused a small cladding defect in pin 306 at the axial position of the peak heat rating. The zircaloy-4 wall failed by complete oxidation, which started at and progressed from the outer, coolant side, surface. Immediately after the detection of fission product activity in the loop water, the irradiation of the bundle was terminated. Microscopic investigations on cross sections of the pins 306 and 309 revealed the presence of oxide pits at the outer surface of the zircalloy-4 wall
Fuel-cladding chemical interaction correlation for mixed-oxide fuel pins
International Nuclear Information System (INIS)
Lawrence, L.A.
1986-10-01
A revised wastage correlation was developed for FCCI with fabrication and operating parameters. The expansion of the data base to 305 data sets provided sufficient data to employ normal statistical techniques for calculation of confidence levels without unduly penalizing predictions. The correlation based on 316 SS cladding also adequately accounts for limited measured depths of interaction for fuel pins with D9 and HTq cladding
Pinning, flux diodes and ratchets for vortices interacting with conformal pinning arrays
International Nuclear Information System (INIS)
Olson Reichhardt, C. J.; Wang, Y. L.; Argonne National Laboratory; Xiao, Z. L.; Northern Illinois University, DeKalb, IL
2016-01-01
A conformal pinning array can be created by conformally transforming a uniform triangular pinning lattice to produce a new structure in which the six-fold ordering of the original lattice is conserved but where there is a spatial gradient in the density of pinning sites. Here we examine several aspects of vortices interacting with conformal pinning arrays and how they can be used to create a flux flow diode effect for driving vortices in different directions across the arrays. Under the application of an ac drive, a pronounced vortex ratchet effect occurs where the vortices flow in the easy direction of the array asymmetry. When the ac drive is applied perpendicular to the asymmetry direction of the array, it is possible to realize a transverse vortex ratchet effect where there is a generation of a dc flow of vortices perpendicular to the ac drive due to the creation of a noise correlation ratchet by the plastic motion of the vortices. We also examine vortex transport in experiments and compare the pinning effectiveness of conformal arrays to uniform triangular pinning arrays. In conclusion, we find that a triangular array generally pins the vortices more effectively at the first matching field and below, while the conformal array is more effective at higher fields where interstitial vortex flow occurs.
Analisis Harmonisa Inverter PWM Satu Fasa
Rejeki Simanjorang
2008-01-01
Pada tesis ini dianalisis harmonisa inverter PWM satu fasa. Inverter PWM satu fasa yang akan ditinjau adalah inverter satu fasa jembatan penuh (konvensional) dan inverter komposit. Analisis difokuskan pada penentuan pola penyaklaran yang optimum agar pembangkitan harmonisa dan switching losses inverter rendah. Untuk menentukan pola penyaklaran optimum maka dilakukan analisis yang berbasis pada rangkaian ekivalen harmonisa inverter satu fasa. Dengan menggunakan pola penyaklaran optimum, kedua ...
French approach in fuel pin modelling for fast reactors
Energy Technology Data Exchange (ETDEWEB)
Pascard, R [CEA-Centre de Fontenay-aux-Roses, Fontenay-aux-Roses (France)
1979-12-01
The purpose of this paper is to present the general philosophy on the problem of fuel modelling now prevailing in France after a twelve years period of tremendously increasing knowledge on fuel behavior. When the Rapsodie fuel pin was designed in 1962 , little was known about the behavior of a mixed oxide fuel pin under fast flux ; but a large body of knowledge on UO{sub 2} behavior in thermal reactor was available together with some sparse irradiation results on (U Pu)O{sub 2} in French experimental reactors. The performances assigned to the pin were then rather modest in rating (400 w/cm) and in burnup (30,000 MWd/t). The AISI 316 steel in solution annealed state was chosen as cladding material. The clad itself was supposed to deform by thermal creep due to fission gas pressure (100% release), and was affected consequently by a strain limit criteria. The importance of clad temperature ({approx}650 deg.) was considered only in connection with thermal creep, the possibility of a chemical reaction between mixed oxide and clad being at that time hardly suspected. Rapsodie had only been at full power for a few months when appeared the evidence of stainless steel swelling under a fast neutrons flux. This swelling was observed on Rapsodie pins as soon as they experienced sufficient neutrons dose, roughly one year later. This entirely new problem came immediately in the front stage (and is still of major importance today), and was at the origin of the change from the Rapsodie to the Fortissimo core in order to accelerate materials testing versus void swelling by multiplying the flux by a factor two. Even with unforeseen swelling, the design of the Rapsodie and later on Fortissimo pin, allowed not only to reach the goal burnup, but to increase it steadily to roughly 100,000 MWd/t. Since then, the French approach in fuel pin design has still retained something of its original simplicity, and technological efficiency, attitude which is justified by the following
Investigation on macroscopic cross section model for BWR pin-by-pin core analysis - 118
International Nuclear Information System (INIS)
Fujita, T.; Tada, K.; Yamamoto, A.; Yamane, Y.; Kosaka, S.; Hirano, G.
2010-01-01
A cross section model used in the pin-by-pin core analysis for BWR is investigated. In the pin-by-pin core calculation method, pin-cell averaged cross sections are calculated for many combinations of state and history variables that have influences on the cross section and are tabulated prior to the core calculations. Variation of a cross section in a core simulator is classified into two different types, i.e., the instantaneous effect and the history effect. The instantaneous effect is incorporated by the variation of cross section which is caused by the instantaneous change of state variables. For this effect, the exposure, the void fraction, the fuel temperature, the moderator temperature and the control rod are used as indexes. The history effect is the cumulative effect of state variables. We treat this effect with a unified approach using the spectral history. To confirm accuracy of the cross section model, the pin-by-pin fission rate distribution and the k-infinity of fuel assembly which are obtained with the tabulated and the reference cross sections are compared. For the instantaneous effect, the present cross section model well reproduces the reference results for all off-nominal conditions. For the history effect, however, considerable differences both on the pin-by-pin fission rate distribution and the k-infinity are observed at high exposure points. (authors)
ANALISIS PENYEBAB BANJIR KALI JUANA
Directory of Open Access Journals (Sweden)
Teguh Marhendi
2017-04-01
Full Text Available Kali Juana yang berada di Kabupaten Pati dan Kudus serta sebagian kecil di Kabupaten Grobogan dan Blora, merupakan kawasan banjir. Kejadian banjir di Kali Juana, sudah menjadi rutinitas setiap musim hujan.Dari Januari sampai bulan Mei 2016tercatat terjadi 11 kejadian banjir dibeberapa wilayah, seperti Kecamatan Kaliwungu, Undaan dan Mejobo (Kab. Kudus serta Pati, Margorejo dan Juwana (Kab. Pati. Kali Juana merupakan bifurkasi Kali Serang pada Pintu Wilalung, yang berfungsi sebagai pintu pengatur banjir (dibangun pada zaman Belanda tahun 1918, melalui Kali Babalan menuju ke Kali Juana. Tulisan inidimaksudkan untuk menganalisis penyebab kejadian banjir di Kali Juana. Analisis dilakukan dengan melakukan kajani dan analisis hujan serta mekanisme aliran. Hasil analisis menunjukkan bahwa kondisi Kali Juana dari pertemuan Kali Logung di pintu Wilalung sampai hilir telah mengalami pendangkalan akibat kemiringan dasar atau topografi yang landai, dan mengakibatkan mudah terjadi sedimentasi sehingga mengurangi kapasitas pengaliran. Hal ini menyebabkan luapan banjir sering menggenangi wilayah Kabupaten Kudus dan Pati.
Canuto, Claudio
2014-01-01
Il presente testo intende essere di supporto ad un secondo insegnamento di Analisi Matematica in quei corsi di studio (quali ad esempio Ingegneria, Informatica, Fisica) in cui lo strumento matematico parte significativa della formazione dell'allievo. I concetti e i metodi fondamentali del calcolo differenziale ed integrale in più variabili, le serie di funzioni e le equazioni differenziali ordinarie sono presentati con l'obiettivo primario di addestrare lo studente ad un loro uso operativo, ma critico. L'impostazione didattica dell'opera ricalca quella usata nel testo parallelo di Analisi Matematica I. La modalità di presentazione degli argomenti ne permette un uso flessibile e modulare. Lo stile adottato privilegia la chiarezza e la linearità dell'esposizione. Il testo organizzato su due livelli di lettura. Uno, più essenziale, permette allo studente di cogliere i concetti indispensabili della materia, di familiarizzarsi con le relative tecniche di calcolo e di trovare le giustificazioni dei principali r...
FRESS pin failure model and its application to E-8 TREAT test
International Nuclear Information System (INIS)
Kalimullah.
1979-01-01
FRESS is a cladding rupture prediction model for an irradiated mixed-oxide LMFBR fuel pin during transient heating based only on the internal pressurization of the cladding by the fission gas released from fuel grains during the transient. The model is applied to the analysis of the hottest PNL-10-53 pin in the 7-pin E-8 TREAT test which simulates a $3/sec transient overpower. Although the uncertainties of the inputs to the temperature calculation done with the COBRA code have not been included, the uncertain input parameters to FRESS have been varied over their estimated uncertainties. The cladding rupture predictions are a few tens of milliseconds late compared to the most probable failure time detected in the test. However, these calculations seem to indicate that fisson gas pressure is a significant mechanism for causing clad rupture in this test
ANALISIS VARIABILITAS CURAH HUJAN DAN SUHU DI BALI
Directory of Open Access Journals (Sweden)
Ogi Setiawan
2017-01-01
Full Text Available Indonesia sebagai negara kepulauan yang terdiri dari pulau-pulau besar dan kecil menjadi sangat rentan terhadap dampak perubahan iklim. Salah satu pulau yang juga rentan terhadap perubahan iklim adalah pulau Bali. Dampak potensial adanya perubahan iklim adalah perubahan pola hujan, peningkatan suhuudaradankenaikanpermukaanlaut. Sektoryangakanmenerimadampakperubahaniklimdengan serius adalah sektor kehutanan dan pertanian. Untuk mendukung upaya mitigasi dan adaptasi maka diperlukan informasi perubahan iklim yang terjadi. Penelitian ini bertujuan untuk mengetahui variabilitas iklim di Bali. Metode yang digunakan adalah analisis kecenderungan curah hujan, analisis perubahan suhu udara, analisis perubahan tipe iklim dan analisis pergeseran bulan basah, lembab dan kering. Data hujan yang digunakan adalah data hujan dari GPCC (1961-1998 dan BMKG Bali (19992008, sedangkan data suhu berasal dari BMKG Bali (2004-2008. Hasil analisis menunjukkan bahwa di pulau Bali secara umum sudah mengalami perubahan iklim. Tipe iklim berdasarkan Schmidt-Ferguson mengalami perubahan dari relatif basah menjadi agak kering. Suhu udara rata-rata bulanan serta curah hujan bulanan dan tahunan memiliki kecenderungan yang semakin meningkat. Bulan basah dan bulan kering telah mengalami pergeseran dan perubahan jumlahnya. Dampak perubahan iklim terhadap ekosistem hutan di Bali belum diketahui dengan pasti, namun terdapat beberapa implikasi perubahan iklim terhadap sektor kehutanan diantaranya kebakaran hutan dan perubahan jadwal penanaman.
A physico-genetic module for the polarisation of auxin efflux carriers PIN-FORMED (PIN)
Hernández-Hernández, Valeria; Barrio, Rafael A.; Benítez, Mariana; Nakayama, Naomi; Romero-Arias, José Roberto; Villarreal, Carlos
2018-05-01
Intracellular polarisation of auxin efflux carriers is crucial for understanding how auxin gradients form in plants. The polarisation dynamics of auxin efflux carriers PIN-FORMED (PIN) depends on both biomechanical forces as well as chemical, molecular and genetic factors. Biomechanical forces have shown to affect the localisation of PIN transporters to the plasma membrane. We propose a physico-genetic module of PIN polarisation that integrates biomechanical, molecular, and cellular processes as well as their non-linear interactions. The module was implemented as a discrete Boolean model and then approximated to a continuous dynamic system, in order to explore the relative contribution of the factors mediating PIN polarisation at the scale of single cell. Our models recovered qualitative behaviours that have been experimentally observed and enable us to predict that, in the context of PIN polarisation, the effects of the mechanical forces can predominate over the activity of molecular factors such as the GTPase ROP6 and the ROP-INTERACTIVE CRIB MOTIF-CONTAINING PROTEIN RIC1.
ANALISIS POSITIONING RESTORAN CEPAT SAJI
Directory of Open Access Journals (Sweden)
Osa Omar Sharif
2017-04-01
Full Text Available Penelitian ini bertujuan untuk meneliti positioning restoran cepat saji McDonald's, Kentucky Fried Chicken, California Fried Chicken, A&W, dan Texas Chicken. Penelitian dilakukan di Kota Bandung dengan mengambil sebanyak 400 responden. Analisis yang digunakan dalam penelitian ini adalah analisis multidimensional scaling, analisis memberikan gambaran positioning dari restoran cepat saji yang ditampilkan dalam perceptual map. Restoran cepat saji yang memiliki layanan paling baik adalah McD dan yang memiliki layanan paling buruk adalah CFC. Restoran cepat saji yang memiliki rasa makanan paling enak adalah McD dan yang memiliki rasa makanan tidak enak adalah CFC. KFC dinilai paling ideal karena selalu berhasil menduduki peringkat satu dan dua jika dilihat dari sudut pandang restoran cepat saji yang lain. Pesaing terdekat McD adalah KFC. McD mendapatkan ranking pertama dari segi atribut layanan, kebersihan, variasi makanan, dan rasa makanan. Dengan posisi seperti ini McD seharusnya tetap menjaga kualitas layanan, kebersihan, variasi makanan, dan rasa makanan agar konsumen tetap memilih untuk datang ke McD. KFC sebaiknya tetap menjaga suasana yang membuat konsumen nyaman akan suasana di dalam atau diluar restoran
Improved pinning by multiple in-line damage
Energy Technology Data Exchange (ETDEWEB)
Weinstein, Roy [Beam Particle Dynamics Laboratories, University of Houston, Houston, TX 77204-5005 (United States); Sawh, Ravi-Persad [Beam Particle Dynamics Laboratories, University of Houston, Houston, TX 77204-5005 (United States); Gandini, Alberto [Beam Particle Dynamics Laboratories, University of Houston, Houston, TX 77204-5005 (United States); Parks, Drew [Beam Particle Dynamics Laboratories, University of Houston, Houston, TX 77204-5005 (United States)
2005-02-01
Columnar pinning centres provide the largest pinning potential, U{sub pin}, but not the greatest J{sub c} or pinnable field, B{sub pin}. Characteristics of ion-generated columnar defects which limit J{sub c} and B{sub pin} are discussed, including reduction of the percolation path, and the need for a larger number of columns of damage, for pinning, than are usually estimated. It is concluded that columnar pinning centres limit B{sub pin} to less than 4 T, and also severely reduce J{sub c}. The goal of maximizing U{sub pin}, via columnar centres, appears to have obscured a more rewarding approach and resulted in neglect of a large regime of ion interactions. Evidence is reviewed that multiple in-line damage (MILD), described herein, can provide orders of magnitude higher J{sub c} and B{sub pin}, despite providing lower U{sub pin}. The MILD pinning centre morphology is discussed, and it is estimated that for present-day large grain high T{sub c} superconductors, a J{sub c} value of {approx}10{sup 6}Acm{sup -2} is obtainable at 77 K, even when crystal plane alignment and weak links are not improved. In addition, the pinned field is increased by over an order of magnitude. An experiment is proposed to confirm these calculations, directly compare MILD pinning to continuous columnar pinning, and determine the optimum MILD structure. Applications of MILD pinning are discussed.
International Nuclear Information System (INIS)
Patenaude, R. S.
1985-01-01
A fuel pin transfer tool has a latching device of the collet type attached to a first member movable vertically through a long work stroke enabling a fuel pin in an under water assembly to be engaged and withdrawn therefrom or placed therein and released. The latching device has a collet provided with a plurality of resilient fingers having cam portions normally spaced apart to receive the upper end of a fuel pin between them and a second member, movable vertically through a short stroke relative to the first member is provided with cam portions engageable with those of the fingers and is yieldably and resiliently held in a raised position in which its cam portions engage those of the fingers and force the fingers into their pin-gripping positions. When a predetermined force is applied to the second member, it is so moved that its cam portions are disengaged from the cam portions of the fingers permitting the latter to move into their normal relationship in which a gripped pin is released or another pin received but with their pin-gripping relationship positively re-established and maintained once the force on the tubular member is lessened. Movement of the first member in either direction and movement of the second member into its raised position is attended by forces inadequate to affect the integrity of fuel pin cladding. That force is applied in the preferred embodiment, by a power operated actuator which is within the upper portion of a housing and, in the preferred embodiment, carried by the long stroke member but always in the upper housing portion which is of a material sufficiently translucent to enable the actuator to be observed throughout the work stroke and is sufficiently light in weight to prevent the tool from being top heavy
Role of Pin1 in UVA-induced cell proliferation and malignant transformation in epidermal cells
International Nuclear Information System (INIS)
Han, Chang Yeob; Hien, Tran Thi; Lim, Sung Chul; Kang, Keon Wook
2011-01-01
Highlights: → Pin1 expression is enhanced by low energy UVA irradiation in both skin tissues of hairless mice and JB6 C141 epidermal cells. → UVA irradiation increases activator protein-1 activity and cyclin D1 in a Pin1-dependent manner. → UVA potentiates EGF-inducible, anchorage-independent growth of epidermal cells, and this is suppressed by Pin1 inhibition or by anti-oxidant. -- Abstract: Ultraviolet A (UVA) radiation (λ = 320-400 nm) is considered a major cause of human skin cancer. Pin1, a peptidyl prolyl isomerase, is overexpressed in most types of cancer tissues and plays an important role in cell proliferation and transformation. Here, we demonstrated that Pin1 expression was enhanced by low energy UVA (300-900 mJ/cm 2 ) irradiation in both skin tissues of hairless mice and JB6 C141 epidermal cells. Exposure of epidermal cells to UVA radiation increased cell proliferation and cyclin D1 expression, and these changes were blocked by Pin1 inhibition. UVA irradiation also increased activator protein-1 (AP-1) minimal reporter activity and nuclear levels of c-Jun, but not c-Fos, in a Pin1-dependent manner. The increases in Pin1 expression and in AP-1 reporter activity in response to UVA were abolished by N-acetylcysteine (NAC) treatment. Finally, we found that pre-exposure of JB6 C141 cells to UVA potentiated EGF-inducible, anchorage-independent growth, and this effect was significantly suppressed by Pin1inhibition or by NAC.
IDENTIFIKASI MISKONSEPSI SISWA SMP PADA KONSEP FOTOSINTESIS MELALUI ANALISIS GAMBAR
Directory of Open Access Journals (Sweden)
Devi Ariandini
2014-01-01
Full Text Available Tujuan dari penelitian ini adalah untuk mengidentifikasi miskonsepsi siswa dengan analisis menggambar. Tiga puluh empat siswa di kelas 8 di sekolah menengah pertama digunakan sebagai subyek dalam penelitian ini. Teknik sampel menggunakan teknik purposive sampling. Data yang diperlukan untuk penelitian ini dikumpulkan melalui kuesioner, menggambar analisis rubrik, dan wawancara. Identifikasi Kesalahpahaman ditentukan dengan menggambar siswa berdasarkan menggambar kriteria klasifikasi oleh Kose (2008. Siswa diperintahkan untuk menarik tentang konsep fotosintesis setelah proses pembelajaran. Gambar siswa dianalisis dengan rubrik dan setelah itu mereka diwawancarai. Hasil penelitian menunjukkan tidak semua tingkat kriteria menggambar dari tingkat 1 sampai 5 diidentifikasi. Dari hasil analisa, gambar paling banyak ditemukan adalah pada tingkat 4. Gambar pada tingkat 4 dikategorikan sebagai gambar lengkap konsep fotosintesis dan tidak ada kesalahpahaman ditemukan. Berdasarkan gambar mereka, ada siswa 2,9% diidentifikasi yang diselenggarakan kesalahpahaman. Ada perbedaan jumlah siswa yang diadakan kesalahpahaman antara gambar hasil analisis dan hasil wawancara. Dari hasil wawancara, ada siswa 35,2% dimiliki kesalahpahaman, lebih dari menggambar hasil analisis. Ini berarti bahwa identifikasi kesalahpahaman melalui analisis gambar tidak efektif. Kesalahpahaman siswa yang paling sering terjadi pada konsep fotosintesis adalah tempat berlangsungnya fotosintesis. Faktor yang membuat kesalahpahaman siswa yaitu karena siswa itu sendiri dan lingkungannya. Kata Kunci: fotosintesis, kesalahpahaman, konsep, menggambar analisis
Fabrication of Fast Reactor Fuel Pins for Test Irradiations
Energy Technology Data Exchange (ETDEWEB)
Karsten, G. [Institute for Applied Reactor Physics, Kernforschungszentrum Karlsruhe, Karlsruhe, Federal Republic of Germany (Germany); Dippel, T. [Institute for Radiochemistry, Kernforschungszentrum Karlsruhe, Karlsruhe, Federal Republic of Germany (Germany); Laue, H. J. [Institute for Applied Reactor Physics, Kernforschungszentrum Karlsruhe, Karlsruhe, Federal Republic of Germany (Germany)
1967-09-15
An extended irradiation programme is being carried out for the fuel element development of the Karlsruhe fast breeder project. A very important task within the programme is the testing of plutonium-containing fuel pins in a fast-reactor environment. This paper deals with fabrication of such pins by our laboratories at Karlsruhe. For the fast reactor test positions at present envisaged a fuel with 15% plutonium and the uranium fully enriched is appropriate. Hie mixed oxide is both pelletized and vibro-compacted with smeared densities between 80 and 88% theoretical. The pin design is, for example, such that there are two gas plena at the top and bottom, and one blanket above the fuel with the fuel zone fitting to the test reactor core length. The specifications both for fuel and cladding have been adapted to the special purpose of a fast-breeder reactor - the outer dimensions, the choice of cladding and fuel types, the data used and the kind of tests outline the targets of the development. The fuel fabrication is described in detail, and also the powder line used for vibro-compaction. The source materials for the fuel are oxalate PuO{sub 2} and UO{sub 2} from the UF{sub 6} process. The special problems of mechanical mixing and of plutonium homogeneity have been studied. The development of the sintering technique and grain characteristics for vibratory compactive fuel had to overcome serious problems in order to reach 82-83% theoretical. The performance of the pin fabrication needed a major effort in welding, manufacturing of fits and decontamination of the pin surfaces. This was a stimulation for the development of some very subtle control techniques, for example taking clear X-ray photographs and the tube testing. In general the selection of tests was a special task of the production routine. In conclusion the fabrication of the pins resulted in valuable experiences for the further development of fast reactor fuel elements. (author)
High-performance whole core Pin-by-Pin calculation based on EFEN-SP_3 method
International Nuclear Information System (INIS)
Yang Wen; Zheng Youqi; Wu Hongchun; Cao Liangzhi; Li Yunzhao
2014-01-01
The EFEN code for high-performance PWR whole core pin-by-pin calculation based on the EFEN-SP_3 method can be achieved by employing spatial parallelization based on MPI. To take advantage of the advanced computing and storage power, the entire problem spatial domain can be appropriately decomposed into sub-domains and the assigned to parallel CPUs to balance the computing load and minimize communication cost. Meanwhile, Red-Black Gauss-Seidel nodal sweeping scheme is employed to avoid the within-group iteration deterioration due to spatial parallelization. Numerical results based on whole core pin-by-pin problems designed according to commercial PWRs demonstrate the following conclusions: The EFEN code can provide results with acceptable accuracy; Communication period impacts neither the accuracy nor the parallel efficiency; Domain decomposition methods with smaller surface to volume ratio leads to greater parallel efficiency; A PWR whole core pin-by-pin calculation with a spatial mesh 289 × 289 × 218 and 4 energy groups could be completed about 900 s by using 125 CPUs, and its parallel efficiency is maintained at about 90%. (authors)
MICROCONTROLLER PIN CONFIGURATION TOOL
Bhaskar Joshi; F. Mohammed Rizwan; Dr. Rajashree Shettar
2012-01-01
Configuring the micro controller with large number of pins is tedious. Latest Infine on microcontroller contains more than 200 pins and each pin has classes of signals. Therefore the complexity of the microcontroller is growing. It evolves looking into thousands of pages of user manual. For a user it will take days to configure the microcontroller with the peripherals. We need an automated tool to configure the microcontroller so that the user can configure the microcontroller without having ...
Stress relaxation of thermally bowed fuel pins
International Nuclear Information System (INIS)
Crossland, I.G.; Speight, M.V.
1983-01-01
The presence of cross-pin temperature gradients in nuclear reactor fuel pins produces differential thermal expansion which, in turn, causes the fuel pin to bow elastically. If the pin is restrained in any way, such thermal bowing causes the pin to be stressed. At high temperatures these stresses can relax by creep and it is shown here that this causes the pin to suffer an additional permanent deflection, so that when the cross-pin temperature difference is removed the pin remains bowed. By representing the cylindrical pin by an equivalent I-beam, the present work examines this effect when it takes place by secondary creep. Two restraint systems are considered, and it is demonstrated that the rate of relaxation depends mainly upon the creep equation, and hence the temperature, and also the magnitude of the initial stresses. (author)
Lightning Pin Injection Testing on MOSFETS
Ely, Jay J.; Nguyen, Truong X.; Szatkowski, George N.; Koppen, Sandra V.; Mielnik, John J.; Vaughan, Roger K.; Wysocki, Philip F.; Celaya, Jose R.; Saha, Sankalita
2009-01-01
Lightning transients were pin-injected into metal-oxide-semiconductor field-effect transistors (MOSFETs) to induce fault modes. This report documents the test process and results, and provides a basis for subsequent lightning tests. MOSFETs may be present in DC-DC power supplies and electromechanical actuator circuits that may be used on board aircraft. Results show that unprotected MOSFET Gates are susceptible to failure, even when installed in systems in well-shielded and partial-shielded locations. MOSFET Drains and Sources are significantly less susceptible. Device impedance decreased (current increased) after every failure. Such a failure mode may lead to cascading failures, as the damaged MOSFET may allow excessive current to flow through other circuitry. Preliminary assessments on a MOSFET subjected to 20-stroke pin-injection testing demonstrate that Breakdown Voltage, Leakage Current and Threshold Voltage characteristics show damage, while the device continues to meet manufacturer performance specifications. The purpose of this research is to develop validated tools, technologies, and techniques for automated detection, diagnosis and prognosis that enable mitigation of adverse events during flight, such as from lightning transients; and to understand the interplay between lightning-induced surges and aging (i.e. humidity, vibration thermal stress, etc.) on component degradation.
Automated system for loading nuclear fuel pins
International Nuclear Information System (INIS)
Marshall, J.L.
1983-10-01
A completely automatic and remotely controlled fuel pin fabrication system is being designed by the Westinghouse Hanford Company. The Pin Operations System will produce fuel pins for the Fast Flux Test Facility (FFTF) and the Clinch River Breeder Reactor Plant (CRBRP). The system will assemble fuel pin components into cladding tubes in a controlled environment. After fuel loading, the pins are filled with helium, the tag gas capsules are inserted, and the top end cap welded. Following welding, the pins are surveyed to assure they are free of contamination and then the pins are helium leak tested
Energy Technology Data Exchange (ETDEWEB)
Liu, Tongzheng, E-mail: liu.tongzheng@mayo.edu [Division of Oncology Research, Department of Oncology, Mayo Clinic, Rochester, MN 55905 (United States); Schneider, Ryan A., E-mail: schneiderr@findlay.edu [College of Pharmacy, The University of Findlay, Findlay, OH 45840 (United States); Hoyt, Dale G., E-mail: hoyt.27@osu.edu [The Dorothy M. Davis Heart and Lung Research Institute, and the Division of Pharmacology, College of Pharmacy, The Ohio State University, 500 West Twelfth Avenue, Columbus, OH 43210 (United States)
2011-10-28
Highlights: Black-Right-Pointing-Pointer Depletion of PIN1 increases inhibitory effect of calpastatin against calpain in endothelial cells. Black-Right-Pointing-Pointer PIN1 associates with calpastatin. Black-Right-Pointing-Pointer PIN1, but not mutants, reduces the inhibitory activity of calpastatin in vitro. Black-Right-Pointing-Pointer Depletion of calpastatin shows that it is required for PIN1 depletion to reduce calpain activity. -- Abstract: The peptidyl-proline isomerase, protein never in mitosis gene A interacting-1 (PIN1) binds and isomerizes proteins phosphorylated on serine/threonine before a proline. It was previously found that depletion of PIN1 greatly increased induction of cyclooxygenase-2 and inducible nitric oxide synthase by lowering calpain activity in murine aortic endothelial cells (MAEC). Here we investigated the effect of PIN1 on the endogenous inhibitor of heterodimeric {mu}- and m-calpains, calpastatin. MAEC were transduced with small hairpin (sh) RNA to knock down PIN1 (KD) or an inactive Control shRNA. Cells were also treated with non-targeted double stranded small inhibitory RNA (siRNA) or siRNA designed to deplete calpastatin. Despite reducing calpain activity, PIN1 KD did not significantly affect the expression of {mu}- and m-calpains, or calpastatin, compared to Control shRNA. Instead, depletion of PIN1 increased the inhibitory activity of calpastatin. Calpastatin co-immunoprecipitated with endogenous PIN1 and was pulled down with glutathione-S-transferase (GST)-PIN1 fusion protein. Adding GST-PIN1 to KD cell extracts lacking PIN1 reduced calpastatin inhibitory activity. Substrate binding and catalytic domain mutants of PIN1 failed to do so. These results suggest that protein interaction and the proline isomerase functions of PIN1 are required for it to inhibit calpastatin. Furthermore, depletion of calpastatin raised calpain activity and reduced calpain inhibitory activity to similar levels in KD and Control MAEC, indicating that
International Nuclear Information System (INIS)
Liu, Tongzheng; Schneider, Ryan A.; Hoyt, Dale G.
2011-01-01
Highlights: ► Depletion of PIN1 increases inhibitory effect of calpastatin against calpain in endothelial cells. ► PIN1 associates with calpastatin. ► PIN1, but not mutants, reduces the inhibitory activity of calpastatin in vitro. ► Depletion of calpastatin shows that it is required for PIN1 depletion to reduce calpain activity. -- Abstract: The peptidyl-proline isomerase, protein never in mitosis gene A interacting-1 (PIN1) binds and isomerizes proteins phosphorylated on serine/threonine before a proline. It was previously found that depletion of PIN1 greatly increased induction of cyclooxygenase-2 and inducible nitric oxide synthase by lowering calpain activity in murine aortic endothelial cells (MAEC). Here we investigated the effect of PIN1 on the endogenous inhibitor of heterodimeric μ- and m-calpains, calpastatin. MAEC were transduced with small hairpin (sh) RNA to knock down PIN1 (KD) or an inactive Control shRNA. Cells were also treated with non-targeted double stranded small inhibitory RNA (siRNA) or siRNA designed to deplete calpastatin. Despite reducing calpain activity, PIN1 KD did not significantly affect the expression of μ- and m-calpains, or calpastatin, compared to Control shRNA. Instead, depletion of PIN1 increased the inhibitory activity of calpastatin. Calpastatin co-immunoprecipitated with endogenous PIN1 and was pulled down with glutathione-S-transferase (GST)–PIN1 fusion protein. Adding GST–PIN1 to KD cell extracts lacking PIN1 reduced calpastatin inhibitory activity. Substrate binding and catalytic domain mutants of PIN1 failed to do so. These results suggest that protein interaction and the proline isomerase functions of PIN1 are required for it to inhibit calpastatin. Furthermore, depletion of calpastatin raised calpain activity and reduced calpain inhibitory activity to similar levels in KD and Control MAEC, indicating that calpastatin is required for PIN1 depletion to lower calpain activity. Thus, PIN1 apparently restrains
International Nuclear Information System (INIS)
Herrero, Jose Javier; Garcia-Herranz, Nuria; Ahnert, Carol
2011-01-01
There exists an interest in performing full core pin-by-pin computations for present nuclear reactors. In such type of problems the use of a transport approximation like the diffusion equation requires the introduction of correction parameters. Interface discontinuity factors can improve the diffusion solution to nearly reproduce a transport solution. Nevertheless, calculating accurate pin-by-pin IDF requires the knowledge of the heterogeneous neutron flux distribution, which depends on the boundary conditions of the pin-cell as well as the local variables along the nuclear reactor operation. As a consequence, it is impractical to compute them for each possible configuration. An alternative to generate accurate pin-by-pin interface discontinuity factors is to calculate reference values using zero-net-current boundary conditions and to synthesize afterwards their dependencies on the main neighborhood variables. In such way the factors can be accurately computed during fine-mesh diffusion calculations by correcting the reference values as a function of the actual environment of the pin-cell in the core. In this paper we propose a parameterization of the pin-by-pin interface discontinuity factors allowing the implementation of a cross sections library able to treat the neighborhood effect. First results are presented for typical PWR configurations. (author)
Energy Technology Data Exchange (ETDEWEB)
Herrero, Jose Javier; Garcia-Herranz, Nuria; Ahnert, Carol, E-mail: herrero@din.upm.es, E-mail: nuria@din.upm.es, E-mail: carol@din.upm.es [Departamento de Ingenieria Nuclear, Universidad Politecnica de Madrid (Spain)
2011-07-01
There exists an interest in performing full core pin-by-pin computations for present nuclear reactors. In such type of problems the use of a transport approximation like the diffusion equation requires the introduction of correction parameters. Interface discontinuity factors can improve the diffusion solution to nearly reproduce a transport solution. Nevertheless, calculating accurate pin-by-pin IDF requires the knowledge of the heterogeneous neutron flux distribution, which depends on the boundary conditions of the pin-cell as well as the local variables along the nuclear reactor operation. As a consequence, it is impractical to compute them for each possible configuration. An alternative to generate accurate pin-by-pin interface discontinuity factors is to calculate reference values using zero-net-current boundary conditions and to synthesize afterwards their dependencies on the main neighborhood variables. In such way the factors can be accurately computed during fine-mesh diffusion calculations by correcting the reference values as a function of the actual environment of the pin-cell in the core. In this paper we propose a parameterization of the pin-by-pin interface discontinuity factors allowing the implementation of a cross sections library able to treat the neighborhood effect. First results are presented for typical PWR configurations. (author)
The pinning property of Bi-2212 single crystals with columnar defects
International Nuclear Information System (INIS)
Okamura, Kazunori; Kiuchi, Masaru; Otabe, Edmund Soji; Yasuda, Takashi; Matsushita, Teruo; Okayasu, Satoru
2004-01-01
It is qualitatively understood that the condensation energy density in oxide superconductors, which is one of the essential parameters for determining their pinning strength, becomes large with increasing dimensionality of the superconductor. However, the condensation energy density has not yet been evaluated quantitatively. Its value can be estimated from the elementary pinning force of a known defect. Columnar defects created by heavy ion irradiation are candidates for being such defects. That is, the size and number density of columnar defects can be given. In addition, it is known that two-dimensional vortices like those in Bi-2212 are forced into three-dimensional states by these defects in a magnetic field parallel to the defects. Thus, the condensation energy density can be estimated from the pinning property of the columnar defects even for two-dimensional superconductors. A similar analysis was performed also for three-dimensional Y-123. A discussion is given of the relationship between the condensation energy density and the anisotropy parameter estimated from measurements of anisotropic resistivity and peak field
Analisis Tingkat Kepentingan Dan Kinerja Layanan Automated Teller Machine (Atm) Bank Mandiri
Setiawati, Lenny; Sugiharto, Toto
2008-01-01
Penelitian ini ditujukan untuk menganalisis tingkat kepentingan dan kinerja layananATM Bank Mandiri. Analisis Servqual yang terdiri atas dimensi tangible, realibility,responsiveness, assurance,dan empathy digunakan untuk menganalisis kinerjalayanan ATM. Sementara itu, Customer Satisfaction Index dan ImportancePerformance Analysis yang terdiri atas analisis kuadran dan analisis kesenjangandigunakan untuk menginvestigasi kepuasan pelanggan dan untuk mengidentifikasikandimensi layanan yang kiner...
ANALISIS SPASIAL KEJADIAN DEMAM BERDARAH DENGUE BERDASARKAN KEPADATAN PENDUDUK
Directory of Open Access Journals (Sweden)
Agcrista Permata Kusuma
2016-01-01
Full Text Available Abstrak Puskesmas Kedungmundu merupakan wilayah endemis DBD dengan kasus yang tinggi. Diperlukan upaya dalam menentukan kebijakan strategi pengendalian vektor secara efektif dan efisien. Analisis spasial dalam SIG dapat digunakan untuk mengetahui pola penyebaran dan daerah potensi penularan DBD. Jenis penelitian ini adalah penelitian deskriptif analitik menggunakan pendekatan cross sectional. Teknik pengambilan sampel menggunakan sampel wilayah memperhatikan proporsi sampel dengan jumlah sampel 146 responden. Pengambilan titik koordinat menggunakan GPS. Analisis data menggunakan analisis univariat dan analisis spasial. Hasil perhitungan statistik spasial ANN diperoleh nilai Z-score = -11,054 terdapat pola spasial kasus DBD di wilayah kerja Puskesmas Kedungmundu. Nilai ANN = 0,52 < 1, artinya pola penyebaran kejadian DBD yang terjadi adalah berkerumun. Kesimpulan dalam penelitian ini sebaran kasus DBD memiliki keterkaitan secara spasial dengan kepadatan penduduk. Abstract Kedungmundu PHC is an endemich region with a high case. Be required to determine policy of vector control strategies effectively and efficiently. Spatial analsys in GIS can be used to determine the pattern of distribution and areas of DHF potential transmission. The type this research was analysis descriptive with cross sectional approach. The sampling technique used a sample area of attention to the proportion of the sample with 146 respondents of total sample. Capturing the coordinates used GPS. Data analisys used univariat and spatial analisys. Result of ANN obtained a Z-score= -11,054, there was a spatial pattern of dengue cases in Kedungmundu PHC. ANN value = 0,52 < 1, it meant that the pattern of DHF distribution was clustered. The conclution of this research was DHF distribution cases has spatial correlation with density population.
Analytical method for reconstruction pin to pin of the nuclear power density distribution
International Nuclear Information System (INIS)
Pessoa, Paulo O.; Silva, Fernando C.; Martinez, Aquilino S.
2013-01-01
An accurate and efficient method for reconstructing pin to pin of the nuclear power density distribution, involving the analytical solution of the diffusion equation for two-dimensional neutron energy groups in homogeneous nodes, is presented. The boundary conditions used for analytic as solution are the four currents or fluxes on the surface of the node, which are obtained by Nodal Expansion Method (known as NEM) and four fluxes at the vertices of a node calculated using the finite difference method. The analytical solution found is the homogeneous distribution of neutron flux. Detailed distributions pin to pin inside a fuel assembly are estimated by the product of homogeneous flux distribution by local heterogeneous form function. Furthermore, the form functions of flux and power are used. The results obtained with this method have a good accuracy when compared with reference values. (author)
Analytical method for reconstruction pin to pin of the nuclear power density distribution
Energy Technology Data Exchange (ETDEWEB)
Pessoa, Paulo O.; Silva, Fernando C.; Martinez, Aquilino S., E-mail: ppessoa@con.ufrj.br, E-mail: fernando@con.ufrj.br, E-mail: aquilino@imp.ufrj.br [Coordenacao dos Programas de Pos-Graduacao em Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil)
2013-07-01
An accurate and efficient method for reconstructing pin to pin of the nuclear power density distribution, involving the analytical solution of the diffusion equation for two-dimensional neutron energy groups in homogeneous nodes, is presented. The boundary conditions used for analytic as solution are the four currents or fluxes on the surface of the node, which are obtained by Nodal Expansion Method (known as NEM) and four fluxes at the vertices of a node calculated using the finite difference method. The analytical solution found is the homogeneous distribution of neutron flux. Detailed distributions pin to pin inside a fuel assembly are estimated by the product of homogeneous flux distribution by local heterogeneous form function. Furthermore, the form functions of flux and power are used. The results obtained with this method have a good accuracy when compared with reference values. (author)
ANALISIS KESELAMATAN TERMOHIDROLIK BULK SHIELDING REAKTOR KARTINI
Directory of Open Access Journals (Sweden)
Azizul Khakim
2015-10-01
Full Text Available ABSTRAK ANALISIS KESELAMATAN TERMOHIDROLIK BULK SHIELDING REAKTOR KARTINI. Bulk shielding merupakan fasilitas yang terintegrasi dengan reaktor Kartini yang berfungsi sebagai penyimpanan sementara bahan bakar bekas. Fasilitas ini merupakan fasilitas yang termasuk dalam struktur, sistem dan komponen (SSK yang penting bagi keselamatan. Salah satu fungsi keselamatan dari sistem penanganan dan penyimpanan bahan bakar adalah mencegah kecelakaan kekritisan yang tak terkendali dan membatasi naiknya temperatur bahan bakar. Analisis keselamatan paling kurang harus mencakup analisis keselamatan dari sisi neutronik dan termo hidrolik Bulk shielding. Analisis termo hidrolik ditujukan untuk memastikan perpindahan panas dan proses pendinginan bahan bakar bekas berjalan baik dan tidak terjadi akumulasi panas yang mengancam integritas bahan bakar. Code tervalidasi PARET/ANL digunakan untuk analisis pendinginan dengan mode konveksi alam. Hasil perhitungan menunjukkan bahwa mode pendinginan konvekasi alam cukup memadai dalam mendinginkan panas sisa tanpa mengakibatkan kenaikan temperatur bahan bakar yang signifikan. Kata kunci: Bulk shielding, bahan bakar bekas, konveksi alam, PARET. ABSTRACT THERMAL HYDRAULIC SAFETY ANALYSIS OF BULK SHIELDING KARTINI REACTOR. Bulk shielding is an integrated facility to Kartini reactor which is used for temporary spent fuels storage. The facility is one of the structures, systems and components (SSCs important to safety. Among the safety functions of fuel handling and storage are to prevent any uncontrolable criticality accidents and to limit the fuel temperature increase. Safety analyses should, at least, cover neutronic and thermal hydraulic calculations of the bulk shielding. Thermal hydraulic analyses were intended to ensure that heat removal and the process of the spent fuels cooling takes place adequately and no heat accumulation that challenges the fuel integrity. Validated code, PARET/ANL was used for analysing the
Analisis Semiotik Sajak Bulang Cahaya
Directory of Open Access Journals (Sweden)
Junaidi Junaidi
2014-11-01
Full Text Available Penelitian ini bertujuan menggali makna tanda yang terdapat dalam sajak Bulang Cahaya karya Rida K Liamsi. Untuk menggali makna itu, pendekatan analisis semiotik Roland Barthes digunakan. Hasil penelitian menunjukkan bahwa sajak ini berisi tanda-tanda bersumber dari kosa kata Melayu lama. Sajak ini juga berisi simbol-simbol yang berkaitan dengan kehidupan orang Melayu. Penggunaan kata-kata Melayu lama dan simbol Melayu memperkuat setting Melayu dalam sajak ini. Analisis makna menunjukkan bahwa seseorang merasakan kedukaan sangat mendalam ketika cintanya harus berakhir, tetapi ia terus merasakan kerinduan dengan kekasihnya yang telah pergi. Mitos cinta yang terdapat dalam pusinya adalah orang tahu bahwa putus cinta itu menyakitkan tetapi orang tetap saja jatuh cinta.
Design of a terahertz CW photomixer based on PIN and superlattice PIN devices
DEFF Research Database (Denmark)
Krozer, Viktor; Eichhorn, Finn
2006-01-01
We present the design of a photomixer LO based on standard and superlattice PIN diodes, operating at 1 THz. The design is based on a direct integration of a double slot antenna with the PIN device and a suitable matching circuit. The antenna has been designed together with a dielectric lens using...... Ansoft HFSS EM simulation. The large-signal PIN diode model employed in the work has been improved compared to our previously developed model presented earlier in a 3 THz design. We demonstrate that the antenna characteristic changes drastically with the device in place....
Beginning-of-life gap closure behaviour of experimental PFBR MOX fuel pin
International Nuclear Information System (INIS)
Jayaraj, V.V.; Padalakshmi, M.; Ojha, B.K.; Padma Prabu, C.; Saravanan, T.; Venkiteswaran, C.N.; Philip, John; Muralidharan, N.G.; Joseph, Jojo; Kasiviswanathan, K.V.; Jayakumar, T.
2011-01-01
Mixed oxide fuel with 22 % and 29% plutonium is chosen as the fuel for PFBR for the two fissile zones. Due to the fabrication tolerances in the pellet diameter, fuel has to be preconditioned at a lower linear power for a brief period before raising the power to the rated value of 450 W/cm. PIE was done on an experimental MOX fuel pin irradiated in FBTR for 13 days at a linear power of 400 W/cm for gap closure studies with the objective of optimising the duration of pre-conditioning before raising the power to the design value of 450 W/cm. X-radiography and remote metallography was done on the fuel pin to estimate the axial fuel column elongation and fuel-clad gap. Remote metallography of the fuel pin cross-sections at five axial locations of the fuel column and the subsequent fuel-clad gap measurement has indicated that the average radial gap has reduced from the pre-irradiation value of 75-110 microns to around 12-13 microns along the entire length of the fuel column. This paper will describe the details of examinations and results of the PIE carried out on the MOX fuel pin. (author)
Optimization study on pin tip diameter of an impact-pin nozzle at high pressure ratio
Energy Technology Data Exchange (ETDEWEB)
Kumar, C. Palani; Lee, Kwon Hee [FMTRC, Daejoo Machinery Co. Ltd., Daegu (Korea, Republic of); Park, Tae Choon; Cha, Bong Jun [Engine Components Research Team, Korea Aerospace Research Institute, Daejeon (Korea, Republic of); Kim, Heuy Dong [Dept. of Mechanical Engineering, Andong National University, Andong (Korea, Republic of)
2016-09-15
Wet compression system is typically installed in a gas turbine engine to increase the net power output and efficiency. A crucial component of the wet compression system is the nozzle which generates fine water droplets for injection into the compressor. The main objective of present work is to optimize a kind of nozzle called impact-pin spray nozzle and thereby produce better quality droplets. To achieve this, the dynamics occurring in the water jet impinging on the pin tip, the subsequent formation of water sheet, which finally breaks into water droplets, must be studied. In this manuscript, the progress on the numerical studies on impact-pin nozzle are reported. A small computational domain covering the orifice, pin tip and the region where primary atomization occurs is selected for numerical analysis. The governing equations are selected in three dimensional cartesian form and simulations are performed to predict the dynamics of water jet impinging on the pin. Systematic studies were carried out and the results leading to the choice of turbulence model and the effect of pin tip diameter are reported here. Further studies are proposed to show the future directions of the present research work.
Top-nozzle mounted replacement guide pin assemblies
International Nuclear Information System (INIS)
Gilmore, C.B.; Andrews, W.H.
1993-01-01
A replacement guide pin assembly is provided for aligning a nuclear fuel assembly with an upper core plate of a nuclear reactor core. The guide pin assembly includes a guide pin body having a radially expandable base insertable within a hole in the top nozzle, a ferrule insertable within the guide pin base and capable of imparting a radially and outwardly directed force on the expandable base to expand it within the hole of the top nozzle and thereby secure the guide pin body to the top nozzle in response to a predetermined displacement of the ferrule relative to the guide pin body along its longitudinal axis, and a lock screw interfitted with the ferrule and threaded into the guide pin body so as to produce the predetermined displacement of the ferrule. (author)
Directory of Open Access Journals (Sweden)
Ahmad Subki
2018-02-01
Full Text Available Audio forensik merupakan salah satu ilmu yang mnyandingkan antara ilmu pengetahuan dan metode ilmiah dalam proses analisis rekaman suara untuk membantu dan mendukung pengungkapan suatu tindak kejahatan yang diperlukan dalam proses persidangan. Undang-undang ITE No.19 Tahun 2016 menyebutkan bahwa rekaman suara merupakan salah satu alat bukti digital yang sah dan dapat digunakan sebagai penguat dakwaan. Rekaman suara yang merupakan barang bukti digital sangatlah mudah dan rentan dimanipulasi, baik secara sengaja maupun tidak disengaja. Pada penelitian ini dilakukan analisis terkait tingkat kemiripan antara rekaman suara voice changer dengan rekaman suara asli menggunakan analisis pitch, formant dan spectogram, rekaman suara yang dianalisis ada dua jenis rekaman suara yaitu suara laki-laki dan suara perempuan. Rekaman suara voice changer dan rekaman suara asli, diekstrak menggunakan tools praat kemudian informasi yang diperoleh dianalisis dengan analisis statistik pitch, formant dan spectrogrammenggunakan tools gnumeric. Penelitian ini menghasilkan bahwa analisis rekaman suara voice changer dengan rekaman suara asli dapat menggunakan analisis statistik pitch, formant dan spectrogram, rekaman suara voice changer A memiliki tingkat kemiripan yang paling tinggi dengan rekaman suara asli pada posisi low pitch, sedangkan voice changer yang lain lebih sulit untuk diidentifikasi.
Xing, Zhou; Li, Shu-Hui; Wu, Bao-Shan; Wang, Xin; Wang, Lu-Yao; Wang, Tan; Liu, Hao-Ran; Zhang, Mei-Lin; Yun, Da-Qin; Deng, Lin-Long; Xie, Su-Yuan; Huang, Rong-Bin; Zheng, Lan-Sun
2018-06-01
Interface engineering that involves in the metal cathodes and the electron transport layers (ETLs) facilitates the simultaneous improvement of device performances and stability in perovskite solar cells (PSCs). Herein, low-temperature solution-processed cerium oxide (CeOx) films are prepared by a facile sol-gel method and employed as the interface layers between [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM) and an Ag back contact to form PC61BM/CeOx double ETLs. The introduction of CeOx enables electron extraction to the Ag electrode and protects the underlying perovskite layer and thus improves the device performance and stability of the p-i-n PSCs. The p-i-n PSCs with double PC61BM/CeOx ETLs demonstrate a maximum power conversion efficiency (PCE) of 17.35%, which is superior to those of the devices with either PC61BM or CeOx single ETLs. Moreover, PC61BM/CeOx devices exhibit excellent stability in light soaking, which is mainly due to the chemically stable CeOx interlayer. The results indicate that CeOx is a promising interface modification layer for stable high-efficiency PSCs.
International Nuclear Information System (INIS)
Fukuda, S.K.
1978-05-01
Examinations of HEDL 61-pin subassemblies comprised of 5.84 mm (0.230) inch diameter mixed-oxide fuel pins with 1.02 mm (0.040'') diameter spacer wire (PNL-9, -10, -11, HEDL-N-E, -N-F), showed severe cladding and spacer wire wear after irradiation in EBR-II. A comparison of a large number of design, fabrication, and irradiation parameters for all of the HEDL subassemblies indicated that the porosity per ring of fuel pins correlated significantly with the occurrence of wear on the fuel pins. The porosity per ring is the clearance between the flat-to-flat pin bundle dimension and the inner hex can dimension divided by the number of hexagonal fuel pin rings in the subassembly. The porosity per ring for PNL-9, -10, -11 and HEDL-N-E was 0.15 mm/ring (6 mils/ring) and 0.18 mm/ring (7 mils/ring) for the HEDL-N-F subassembly. Since the original FTR subassembly design had a porosity/ring spread of 0.04 mm/ring to 0.16 mm/ring (1.67 to 6.11 mils/ring) an additional series of irradiation tests was conducted to confirm that a tighter fuel pin bundle would eliminate the wear
BARS - a heterogeneous code for 3D pin-by-pin LWR steady-state and transient calculation
International Nuclear Information System (INIS)
Avvakumov, A.V.; Malofeev, V.M.
2000-01-01
A 3D pin-by-pin dynamic model for LWR detailed calculation was developed. The model is based on a coupling of the BARS neutronic code with the RELAP5/MOD3.2 thermal hydraulic code. This model is intended to calculate a fuel cycle, a xenon transient, and a wide range of reactivity initiated accidents in a WWER and a PWR. Galanin-Feinberg heterogeneous method was realized in the BARS code. Some results for a validation of the heterogeneous method are presented for reactivity coefficients, a pin-by-pin power distribution, and a fast pulse transient. (Authors)
International Nuclear Information System (INIS)
Benkraouda, M.; Obaidat, I.M.; Al Khawaja, U.
2006-01-01
We have conducted extensive series of molecular dynamic simulations on driven vortex lattices interacting with periodic square arrays of pinning sites. In solving the over damped equation of vortex motion we took into account the vortex-vortex repulsion interaction, the attractive vortex-pinning interaction, and the driving Lorentz force at several values of temperature. We have studied the effect of varying the driving Lorentz force and varying the pinning strength on the critical current for several pinning densities, and temperature values. We have found that the pinning strength play an important role in enhancing the critical current over the whole temperature range. At low temperatures, the critical current was found to increase linearly with increasing the pinning strengths for all pinning densities. As the temperature increases, the effect of small pinning strengths diminishes and becomes insignificant at high temperatures
Pinning synchronization of a mobile agent network
International Nuclear Information System (INIS)
Wang, Lei; Sun, You-xian
2009-01-01
We investigate the problem of controlling a group of mobile agents in a plane in order to move them towards a desired orbit via pinning control, in which each agent is associated with a chaotic oscillator coupled with those of neighboring agents, and the pinning strategy is to have the common linear feedback acting on a small fraction of agents by random selection. We explore the effects of the pinning probability, feedback gains and agent density in the pinning synchronization of a mobile agent network under a fast-switching constraint, and perform numerical simulations for validation. In particular, we show that there exists a critical pinning density for network synchronization with an unbounded region: above the threshold, the dynamical network can be controlled by pinning; below it, anarchy prevails. And for the network with a single bounded synchronization region, pinning control has little effect as regards enhancing network synchronizability
Aljawhary, Dana; Zhao, Ran; Lee, Alex K Y; Wang, Chen; Abbatt, Jonathan P D
2016-03-10
Formation of secondary organic aerosol (SOA) involves atmospheric oxidation of volatile organic compounds (VOCs), the majority of which are emitted from biogenic sources. Oxidation can occur not only in the gas-phase but also in atmospheric aqueous phases such as cloudwater and aerosol liquid water. This study explores for the first time the aqueous-phase OH oxidation chemistry of oxidation products of α-pinene, a major biogenic VOC species emitted to the atmosphere. The kinetics, reaction mechanisms, and formation of SOA compounds in the aqueous phase of two model compounds, cis-pinonic acid (PIN) and tricarballylic acid (TCA), were investigated in the laboratory; TCA was used as a surrogate for 3-methyl-1,2,3-butanetricarboxylic acid (MBTCA), a known α-pinene oxidation product. Aerosol time-of-flight chemical ionization mass spectrometry (Aerosol-ToF-CIMS) was used to follow the kinetics and reaction mechanisms at the molecular level. Room-temperature second-order rate constants of PIN and TCA were determined to be 3.3 (± 0.5) × 10(9) and 3.1 (± 0.2) × 10(8) M(-1) s(-1), respectively, from which were estimated their condensed-phase atmospheric lifetimes. Aerosol-ToF-CIMS detected a large number of products leading to detailed reaction mechanisms for PIN and MBTCA. By monitoring the particle size distribution after drying, the amount of SOA material remaining in the particle phase was determined. An aqueous SOA yield of 40 to 60% was determined for PIN OH oxidation. Although recent laboratory studies have focused primarily on aqueous-phase processing of isoprene-related compounds, we demonstrate that aqueous formation of SOA materials also occurs from monoterpene oxidation products, thus representing an additional source of biogenically driven aerosol formation.
Vortex lattice melting, pinning and kinetics
International Nuclear Information System (INIS)
Doniach, S.; Ryu, S.; Kapitulnik, A.
1994-01-01
The phenomenology of the high T c superconductors is discussed both at the level of the thermodynamics of melting of the Abrikosov flux lattice and in terms of the melting and kinetics of the flux lattice for a pinned system. The authors review results on 3D melting obtained by a Monte Carlo simulation approach in which the 2D open-quotes pancakeclose quotes vortices are treated as statistical variables. The authors discuss pinning in the context of the strong pinning regime in which the vortex density given in terms of the applied field B is small compared to that represented by an effective field B pin measuring the pinning center density. The authors introduce a new criterion for the unfreezing of a vortex glass on increase of magnetic field or temperature, in the strong pinning, small field unit. The authors model this limit in terms of a single flux line interacting with a columnar pin. This model is studied both analytically and by computer simulation. By applying a tilt potential, the authors study the kinetics of the vortex motion in an external current and show that the resulting current-voltage characteristic follows a basic vortex glass-like scaling relation in the vicinity of the depinning transition
COMETHE III J a computer code for predicting mechanical and thermal behaviour of a fuel pin
International Nuclear Information System (INIS)
Verbeek, P.; Hoppe, N.
1976-01-01
The design of fuel pins for power reactors requires a realistic evaluation of their thermal and mechanical performances throughout their irradiation life. This evaluation involves the knowledge of a number of parameters, very intricate and interconnected, for example, the temperature, the restructuring and the swelling rates of the fuel pellets, the dimensions, the stresses and the strains in the clad, the composition and the properties of gases, the inner gas pressure etc. This complex problem can only be properly handled by a computer programme which analyses the fuel pin thermal and mechanical behaviour at successive steps of its irradiation life. This report presents an overall description of the COMETHE III-J computer programme, designed to calculate the integral performance of oxide fuel pins with cylindrical metallic cladding irradiated in thermal or fast flux. (author)
Pin fin compliant heat sink with enhanced flexibility
Schultz, Mark D.
2018-04-10
Heat sinks and methods of using the same include a top and bottom plate, at least one of which has a plurality of pin contacts flexibly connected to one another, where the plurality of pin contacts have vertical and lateral flexibility with respect to one another; and pin slice layers, each having multiple pin slices, arranged vertically between the top and bottom plates such that the plurality of pin slices form substantially vertical pins connecting the top and bottom plates.
Fabrication and characterization of MX-type fuels and fuel pins
International Nuclear Information System (INIS)
Richter, K.; Bartscher, W.; Benedict, U.; Gueugnon, J.F.; Kutter, H.; Sari, C.; Schmidt, H.E.
1978-01-01
This paper summarizes the most important fabrication parameters and characterization of fuel and fuel pins obtained during the investigation of uranium-plutonium carbides, oxicarbides, carbonitrides and nitrides in the past years at the European Institute for Transuranium Elements at Karlsruhe. All preparation methods discussed are based on carbothermic reduction of a mechanical blend of uranium-plutonium oxide and carbon powder. General data for carbothermic reduction processes are discussed (influence of starting material, homogeneity, control of degree of reaction, etc). A survey of different preparation methods investigated is given. Limitations with respect to temperature and atmosphere for both carbothermic reduction processes and sintering conditions for the different compounds are summarized. A special preparation process for mixed carbonitrides with low nitrogen content (U,Pu)sub(1-x)Nsub(x) in the range 0.1 0 C to 1400 0 C by means of a modulated electron beam technique. A scheme is proposed, which allows to predict the thermal properties of MX fuels on the basis of their chemical composition and porosity. Preparation, preirradiation characterization and final controls of fuel test pins for pellet and vibrocompacted type of pins are described and the most important data summarized for all advanced fuels irradiated at Dounreay (DN1) and Rapsodie Fast Reactor (DN2) within the TU irradiation programme
International Nuclear Information System (INIS)
Zhang, B.; Li, G.; Wang, W.; Shangguan, D.; Deng, L.
2015-01-01
This paper introduces the Strategy of multilevel hybrid parallelism of JCOGIN Infrastructure on Monte Carlo Particle Transport for the large-scale full-core pin-by-pin simulations. The particle parallelism, domain decomposition parallelism and MPI/OpenMP parallelism are designed and implemented. By the testing, JMCT presents the parallel scalability of JCOGIN, which reaches the parallel efficiency 80% on 120,000 cores for the pin-by-pin computation of the BEAVRS benchmark. (author)
Development of 3D pseudo pin-by-pin calculation methodology in ANC
International Nuclear Information System (INIS)
Zhang, B.; Mayhue, L.; Huria, H.; Ivanov, B.
2012-01-01
Advanced cores and fuel assembly designs have been developed to improve operational flexibility, economic performance and further enhance safety features of nuclear power plants. The simulation of these new designs, along with strong heterogeneous fuel loading, have brought new challenges to the reactor physics methodologies currently employed in the industrial codes for core analyses. Control rod insertion during normal operation is one operational feature in the AP1000 R plant of Westinghouse next generation Pressurized Water Reactor (PWR) design. This design improves its operational flexibility and efficiency but significantly challenges the conventional reactor physics methods, especially in pin power calculations. The mixture loading of fuel assemblies with significant neutron spectrums causes a strong interaction between different fuel assembly types that is not fully captured with the current core design codes. To overcome the weaknesses of the conventional methods, Westinghouse has developed a state-of-the-art 3D Pin-by-Pin Calculation Methodology (P3C) and successfully implemented in the Westinghouse core design code ANC. The new methodology has been qualified and licensed for pin power prediction. The 3D P3C methodology along with its application and validation will be discussed in the paper. (authors)
ANALISIS PENERAPAN 8 STANDAR NASIONAL PENDIDIKAN PADA SMP NEGERI 2 DOLOPO KABUPATEN MADIUN
Directory of Open Access Journals (Sweden)
Luki Eko Cahyono
2015-10-01
Penelitian ini menggunakan desain penelitian Deskriptif Kualitatif. Jenis penelitian adalah studi kasus. Data yang digunakan adalah data Primer. Teknik pengumpulan data yang digunakan adalah wawancara dan dokumentasi. Teknik keabsahan data adalah Triangulasi Sumber dan teknik analisis data yang digunakan adalah pendekatan Strengths, Weakness, Opportunities, dan Threats (Analisis SWOT. Kesimpulan penelitian ini adalah (1 Hasil analisis Strenght (Kekuatan adalah sekolah sudah merencanakan, melaksanakan dan mengevaluasi sebagian besar indikator dalam pemenuhan Standar Nasional Pendidikan sehingga meningkatkan mutu pendidikan sekolah. (2 Hasil analisis Weakness (kelemahan adalah keterbatasan anggaran dana dan sumber daya manusia baik peserta didik, pendidik, maupun tenaga kependidikan dalam pemenuhan seluruh unsur Standar Nasional Pendidikan. (3 Hasil analisis Opportunities (peluang adalah Pemberian workshop dan pelatihan kepada pendidik dan tenaga kependidikan meningkatkan kualitas pendidikan sekolah, dan perencanaan, pelaksanaan pembiayaan serta evaluasi penganggaran yang baik memberikan dampak positif terhadap semua unsur operasional sekolah maupun sarana prasarana sekolah. (4 Hasil analisis Threats (Tantangan adalah perencanaan, sosialisasi, pelaksanaan dan evaluasi serta tindak lanjut yang tidak dijalankan dengan manajemen yang baik dalam upaya pemenuhan Standar Nasional Pendidikan akan menghambat peningkatan kualitas pendidikan sekolah. (5 Hasil penerapan Standar Nasional Pendidikan pada SMP Negeri 2 Dolopo menggunakan analisis SWOT menunjukkan bahwa Kekuatan lebih besar daripada Kelemahan dan Peluang lebih besar dari Ancaman, yang berarti Standar Nasional Pendidikan telah terpenuhi dan menghasilkan Akreditasi Sekolah nilai A.
Directory of Open Access Journals (Sweden)
Toto Sudiro
2012-11-01
Full Text Available Kehandalan dan umur pakai sistem Thermal Barrier Coating (TBC ditentukan oleh kestabilan lapisan bond coat dan thermal grown oxide (TGO. Sehingga sangatlah penting untuk memahami mekanisme pembentukan dan degradasi lapisan ini. Pada makalah ini akan dibahas analisis struktur mikro lapisan bond coat NiAl yang dideposisikan pada substrat CoCrNi dengan menggunakan gabungan metoda electroplating dan pack-cementation. Pada makalah ini juga dibahas mekanisme pembentukan void disepanjang interface bond coat¬-substrat setelah tes oksidasi.
Integral Fast Reactor fuel pin processor
International Nuclear Information System (INIS)
Levinskas, D.
1993-01-01
This report discusses the pin processor which receives metal alloy pins cast from recycled Integral Fast Reactor (IFR) fuel and prepares them for assembly into new IFR fuel elements. Either full length as-cast or precut pins are fed to the machine from a magazine, cut if necessary, and measured for length, weight, diameter and deviation from straightness. Accepted pins are loaded into cladding jackets located in a magazine, while rejects and cutting scraps are separated into trays. The magazines, trays, and the individual modules that perform the different machine functions are assembled and removed using remote manipulators and master-slaves
Magnetic pinning in superconductor-ferromagnet multilayers
International Nuclear Information System (INIS)
Bulaevskii, L. N.; Chudnovsky, E. M.; Maley, M. P.
2000-01-01
We argue that superconductor/ferromagnet multilayers of nanoscale period should exhibit strong pinning of vortices by the magnetic domain structure in magnetic fields below the coercive field when ferromagnetic layers exhibit strong perpendicular magnetic anisotropy. The estimated maximum magnetic pinning energy for single vortex in such a system is about 100 times larger than the pinning energy by columnar defects. This pinning energy may provide critical currents as high as 10 6 -10 7 A/cm 2 at high temperatures (but not very close to T c ) at least in magnetic fields below 0.1 T. (c) 2000 American Institute of Physics
Corrosion of Ti6Al4V pins produced by direct metal laser sintering
de Damborenea, J. J.; Arenas, M. A.; Larosa, Maria Aparecida; Jardini, André Luiz; de Carvalho Zavaglia, Cecília Amélia; Conde, A.
2017-01-01
Direct Metal Laser Sintering (DMLS) technique allows the manufacturing a wide variety of medical devices for any type of prosthetic surgery (HIP, dental, cranial, maxillofacial) as well as for internal fixation devices (K-Wires or Steinmann Pins). There are a large number of research studies on DMLS, including microstructural characterization, mechanical properties and those based on production quality assurance but the influence of porosity in the corrosion behavior of these materials not been sufficiently considered. In the present paper, surgical pins of Ti6Al4V have been produced by DMLS. After testing in a phosphate buffered saline solution, the surface of the titanium alloy appeared locally covered by a voluminous white oxide. This unexpected behavior was presumably due to the existence of internal defects in the pins as result of the manufacturing process. The importance of these defects-that might act as crevice nucleation sites- has been revealed by electrochemical techniques and confirmed by computed tomography.
Cesium chemistry in GCFR fuel pins
International Nuclear Information System (INIS)
Fee, D.C.; Johnson, C.E.
1979-01-01
The fuel rod design for the Gas Cooled Fast-Breeder Reactor (GCFR) is similar to that employed for the Liquid Metal Fast Breeder Reactor (LMFBR) with the exception of the unique features inherent to the use of helium as the coolant. These unique design features include the use of (1) vented and pressure-equalized fuel rods, and (2) ribbed cladding along 75% of the fuel section. The former design feature enables reduction in cladding thickness and prevention of possible creep collapse of the cladding due to the high coolant pressure (8.5 MPa). The latter design feature brings about improved heat transfer characteristics. Each GCFR fuel rod is vented to a manifold whereby gaseous fission products diffusing out of the fuel pin are retained on charcoal traps. As a result, the internal pressure of a GCFR fuel pin does not increase during irradiation. In addition, the venting system also maintains the pressure within the fuel pin slightly below (0.3 to 0.5 MPa) the coolant pressure outside the fuel pin. Consequently, should a breach occur in the cladding, helium flows into the breached fuel pin thereby minimizing fission product contamination of the coolant. These desirable aspects of a GCFR fuel pin can be maintained only as long as axial gas transport paths are available and operating within the fuel pin
International Nuclear Information System (INIS)
Vignesoult, N.; Atabek, R.; Ducas, S.
1982-06-01
The Fabrice ''hot cell refabrication'' process for small pins from very long irradiated fuel elements was developed at the CEA to allow parametric studies of the irradiation behavior of pins from nuclear power plants. Since this operation required complete assurance of the validity of the process, qualification of the fabrication was performed on test pins, refabricated in the hot cell, as well as irradiation qualification. The latter qualification was intended to demonstrate that, in identical experimental irradiation conditions, the refabricated Fabrice pins behaved in the same way as whole pins with the same initial characteristics. This qualification of the Fabrice process, dealing with more than twenty pins at different burnups, showed that fabrication did not alter: the inherent characteristics of the sampled fuel element and the irradiation behavior of the sampled fuel element [fr
Energy Technology Data Exchange (ETDEWEB)
Sawh, Ravi-Persad; Weinstein, Roy; Gandini, Alberto; Skorpenske, Harley; Parks, Drew, E-mail: Weinstein@uh.ed [Beam Particle Dynamics Laboratories, University of Houston, Houston, TX 77204-5005 (United States); Department of Physics, University of Houston, Houston, TX 77204-5005 (United States); Texas Center for Superconductivity at UH, University of Houston, Houston, TX 77204-5002 (United States)
2009-09-15
The pinning effects of two kinds of U-rich deposits in YBCO (YBa{sub 2}Cu{sub 3}O{sub 7-{delta}}) are compared. One is a five-element compound, (U{sub 0.6}Pt{sub 0.4})YBa{sub 2}O{sub 6}, which is a paramagnetic double perovskite which forms as profuse stable nanosize deposits, and pins very well. The other is a four-element compound, (U{sub 0.4}Y{sub 0.6})BaO{sub 3}, which is a ferromagnetic single perovskite which forms as profuse stable nanosize deposits and pins very weakly or not at all. The pinning comparison is done with nearly equal deposit sizes and number of deposits per unit volume for the two compounds. Evidence for the pinning capability, chemical makeup, x-ray diffraction signature, and magnetic properties of the two compounds is reported.
Tapered leaf support pin for operating plant guide tubes
International Nuclear Information System (INIS)
Land, J.T.; Hopkins, R.J.; Ford, D.E.
1991-01-01
This patent describes a mounting system for removably mounting the lower flange of a control rod guide tube over an opening in the upper core plate of a nuclear reactor comprising at least one elongated support pin mounted on the guide tube lower flange and resiliently receivable in a bore formed in the upper core plate. It comprises a support pin having a longitudinal axis and comprising a first pin portion mountable on the guide tube lower flange, and a second pin portion receivable within the upper core plate bore, the second pin portion including a solid body section adjacent the first pin portion and having an outer diameter which is accommodated by the bore by a close clearance fit; locking means mounted on the first pin portion of the support pin for retaining the guide tube lower flange between the solid body section of the second pin portion and the locking means; and a washer disposed around the first pin portion between the locking means and the control rod guide tube flange, the washer and the locking means including mutually engaging rounded surfaces for eliminating bending moments and stresses on the support pin during mounting of the locking means on the first pin portion of the support pin
Magnetic pinning in superconductor-ferromagnet multilayers
Energy Technology Data Exchange (ETDEWEB)
Bulaevskii, L. N. [Department of Physics and Astronomy, CUNY Lehman College 250 Bedford Park Boulevard West, Bronx, New York 10468-1589 (United States); Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Chudnovsky, E. M. [Department of Physics and Astronomy, CUNY Lehman College, 250 Bedford Park Boulevard West, Bronx, New York 10468-1589 (United States); Maley, M. P. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States)
2000-05-01
We argue that superconductor/ferromagnet multilayers of nanoscale period should exhibit strong pinning of vortices by the magnetic domain structure in magnetic fields below the coercive field when ferromagnetic layers exhibit strong perpendicular magnetic anisotropy. The estimated maximum magnetic pinning energy for single vortex in such a system is about 100 times larger than the pinning energy by columnar defects. This pinning energy may provide critical currents as high as 10{sup 6}-10{sup 7} A/cm{sup 2} at high temperatures (but not very close to T{sub c}) at least in magnetic fields below 0.1 T. (c) 2000 American Institute of Physics.
Galal, Sherif; Safwat, Wael
2017-01-01
The 5th metacarpal fractures accounts for 38% of all hand fractures given that the neck is the weakest point in metacarpals, so neck fracture is the most common metacarpal fracture. Surgical fixation is also advocated for such fractures to prevent mal-rotation of the little finger which will lead to fingers overlap in a clenched fist. Various methods are available for fixation of such fractures, like intramedullary & transverse pinning. There are very few reports in the literature comparing both techniques. Authors wanted to compare outcomes and complications of transverse pinning versus intramedullary pinning in fifth metacarpal's neck fractures. A single-center, parallel group, prospective, randomized study was conducted at an academic Level 1 Trauma Center from October 2014 to December 2016. A total of 80 patients with 5th metacarpal's neck fractures were randomized to pinning using either transverse pinning (group A) or intramedullary pinning (group B). Patients were assessed clinically on range of motion, patient-reported outcome using the Quick-DASH (Disabilities of the Arm, Shoulder, and Hand) questionnaire & radiographically. Two blinded observers assessed outcomes. At final follow up for each patient (12 months) the statistically significant differences were observed in operative time, the transverse pinning group showed shorter operative time, as well as complication rate as complications were observed only in intramedullary pinning group. No differences were found in range of motion or the Quick -DASH score. Both techniques are equally safe and effective treatment option for 5th metacarpal's neck fractures. The only difference was shorter operative time & less incidence of complications in transverse pinning group. Level II, Therapeutic study.
International Nuclear Information System (INIS)
Sakai, K.; Hishida, H.
1978-01-01
Probabilistic fuel pin gap distributions within a wire-spaced fuel subassembly and sensitivities of the related uncertainties to fuel pin gaps are discussed. The analyses consist mainly of expressing a local fuel pin gap in terms of sensitivity functions of the related uncertainties and calculating the corresponding probabilistic distribution through taking all the possible combinations of the distribution of uncertainties. The results of illustrative calculations show that with the reliability level of 0.9987, the maximum deviation of the pin gap at the cladding hot spot of a center fuel subassembly is 8.05% from its nominal value and the corresponding probabilistic pin gap distribution is shifted to the narrower side due to the external confinement of a pin bundle with a wrapper tube. (Auth.)
Automated fuel pin loading system
Christiansen, D.W.; Brown, W.F.; Steffen, J.M.
An automated loading system for nuclear reactor fuel elements utilizes a gravity feed conveyor which permits individual fuel pins to roll along a constrained path perpendicular to their respective lengths. The individual lengths of fuel cladding are directed onto movable transports, where they are aligned coaxially with the axes of associated handling equipment at appropriate production stations. Each fuel pin can be be reciprocated axially and/or rotated about its axis as required during handling steps. The fuel pins are inerted as a batch prior to welding of end caps by one of two disclosed welding systems.
Directory of Open Access Journals (Sweden)
Zhigang Zheng
2017-09-01
Full Text Available Because of the long and unpredictable flowering period in bamboo, the molecular mechanism of bamboo flowering is unclear. Recent study showed that Arabidopsis PIN1-type parvulin 1 (Pin1At is an important floral activator and regulates floral transition by facilitating the cis/trans isomerization of the phosphorylated Ser/Thr residues preceding proline motifs in suppressor of overexpression of CO 1 (SOC1 and agamous-like 24 (AGL24. Whether bamboo has a Pin1 homolog and whether it works in bamboo flowering are still unknown. In this study, we cloned PvPin1, a homolog of Pin1At, from Phyllostachys violascens (Bambusoideae. Bioinformatics analysis showed that PvPin1 is closely related to Pin1-like proteins in monocots. PvPin1 was widely expressed in all tested bamboo tissues, with the highest expression in young leaf and lowest in floral bud. Moreover, PvPin1 expression was high in leaves before bamboo flowering then declined during flower development. Overexpression of PvPin1 significantly delayed flowering time by downregulating SOC1 and AGL24 expression in Arabidopsis under greenhouse conditions and conferred a significantly late flowering phenotype by upregulating OsMADS56 in rice under field conditions. PvPin1 showed subcellular localization in both the nucleus and cytolemma. The 1500-bp sequence of the PvPin1 promoter was cloned, and cis-acting element prediction showed that ABRE and TGACG-motif elements, which responded to abscisic acid (ABA and methyl jasmonate (MeJA, respectively, were characteristic of P. violascens in comparison with Arabidopsis. On promoter activity analysis, exogenous ABA and MeJA could significantly inhibit PvPin1 expression. These findings suggested that PvPin1 may be a repressor in flowering, and its delay of flowering time could be regulated by ABA and MeJA in bamboo.
Zheng, Zhigang; Yang, Xiaoming; Fu, Yaping; Zhu, Longfei; Wei, Hantian; Lin, Xinchun
2017-01-01
Because of the long and unpredictable flowering period in bamboo, the molecular mechanism of bamboo flowering is unclear. Recent study showed that Arabidopsis PIN1-type parvulin 1 (Pin1At) is an important floral activator and regulates floral transition by facilitating the cis/trans isomerization of the phosphorylated Ser/Thr residues preceding proline motifs in suppressor of overexpression of CO 1 (SOC1) and agamous-like 24 (AGL24). Whether bamboo has a Pin1 homolog and whether it works in bamboo flowering are still unknown. In this study, we cloned PvPin1 , a homolog of Pin1At , from Phyllostachys violascens (Bambusoideae). Bioinformatics analysis showed that PvPin1 is closely related to Pin1-like proteins in monocots. PvPin1 was widely expressed in all tested bamboo tissues, with the highest expression in young leaf and lowest in floral bud. Moreover, PvPin1 expression was high in leaves before bamboo flowering then declined during flower development. Overexpression of PvPin1 significantly delayed flowering time by downregulating SOC1 and AGL24 expression in Arabidopsis under greenhouse conditions and conferred a significantly late flowering phenotype by upregulating OsMADS56 in rice under field conditions. PvPin1 showed subcellular localization in both the nucleus and cytolemma. The 1500-bp sequence of the PvPin1 promoter was cloned, and cis -acting element prediction showed that ABRE and TGACG-motif elements, which responded to abscisic acid (ABA) and methyl jasmonate (MeJA), respectively, were characteristic of P. violascens in comparison with Arabidopsis . On promoter activity analysis, exogenous ABA and MeJA could significantly inhibit PvPin1 expression. These findings suggested that PvPin1 may be a repressor in flowering, and its delay of flowering time could be regulated by ABA and MeJA in bamboo.
Robustness of pinning a general complex dynamical network
International Nuclear Information System (INIS)
Wang Lei; Sun Youxian
2010-01-01
This Letter studies the robustness problem of pinning a general complex dynamical network toward an assigned synchronous evolution. Several synchronization criteria are presented to guarantee the convergence of the pinning process locally and globally by construction of Lyapunov functions. In particular, if a pinning strategy has been designed for synchronization of a given complex dynamical network, then no matter what uncertainties occur among the pinned nodes, synchronization can still be guaranteed through the pinning. The analytical results show that pinning control has a certain robustness against perturbations on network architecture: adding, deleting and changing the weights of edges. Numerical simulations illustrated by scale-free complex networks verify the theoretical results above-acquired.
Pinning Mechanisms in YBCO Tapes
Spera, Marcello; Ballarino, Amalia
2015-01-01
In this thesis work, a study on flux pinning mechanisms of commercial YBCO tapes is presented. This study has been performed via critical current characterization using transport (via direct I-V curves) and magnetization (via a Vibrating Sample Magnetometer) measurements. The latter ones turned out to be better concerning the comprehension of the pinning landscape of the provided samples, as a wider range of magnetic fields and temperatures is available for those measurements in the setup I used. The comparison of the experimental data with existing theoretical models allowed me to draw a picture of the pinning mechanisms underlying in each sample, and they turned out to be quite different one another. Moreover, for high-performance research tapes, another interesting feature has been found: the counterplay between the self-field critical current and the in-field one. Very well engineered artificial pinning structures limit the self-field critical current density due to the hi...
UO2 - Zr chemical interaction of PHWR fuel pins under high temperature
International Nuclear Information System (INIS)
Majumdar, P.; Mukhopadhyay, D.; Gupta, S.K.
2001-01-01
At high temperature Zircaloy clad interacts with the UO 2 fuel as well as with the steam to produce oxide layer of a-Zr(O) and ZrO 2 . This layer formation significantly reduces the structural strength of the clad. A computer code SFDCPA/MOD1 has been developed to simulate the interaction and predict the oxide layer thickness for any accidental transient condition. It is well validated with published experimental data on the isothermal and transient temperature condition. The program is applied to Indian Pressurized Heavy Water Reactor (PHWR) fuel pin under certain severe transient condition where it experiences temperature above 1000 C. The study gives an idea of the un-oxidized thickness of Zircaloy, which is an important criterion for fuel integrity. (author)
Enhanced pinning in superconducting thin films with graded pinning landscapes
Motta, M.; Colauto, F.; Ortiz, W. A.; Fritzsche, J.; Cuppens, J.; Gillijns, W.; Moshchalkov, V. V.; Johansen, T. H.; Sanchez, A.; Silhanek, A. V.
2013-05-01
A graded distribution of antidots in superconducting a-Mo79Ge21 thin films has been investigated by magnetization and magneto-optical imaging measurements. The pinning landscape has maximum density at the sample border, decreasing linearly towards the center. Its overall performance is noticeably superior than that for a sample with uniformly distributed antidots: For high temperatures and low fields, the critical current is enhanced, whereas the region of thermomagnetic instabilities in the field-temperature diagram is significantly suppressed. These findings confirm the relevance of graded landscapes on the enhancement of pinning efficiency, as recently predicted by Misko and Nori [Phys. Rev. B 85, 184506 (2012)].
Surface morphology study on chromium oxide growth on Cr films by Nd-YAG laser oxidation process
International Nuclear Information System (INIS)
Dong Qizhi; Hu Jiandong; Guo Zuoxing; Lian Jianshe; Chen Jiwei; Chen Bo
2002-01-01
Grain sized (60-100 nm) Cr 2 O 3 thin films were prepared on Cr thin film surfaces by Nd-YAG laser photothermal oxidation process. Surface morphology study showed crack-free short plateau-like oxide films formed. Increase of dislocation density after pulsed laser irradiation was found. Thin film external surfaces, grain boundaries and dislocations are main paths of laser surface oxidation. Pinning and sealing of grain boundary was the reason that deeper oxidation did not produce. Grain growth and agglomeration of Cr sub-layer yielded tensile stress on the surface Cr 2 O 3 thin film. It was the reason that short plateau-like surface morphology formed and cracks appeared sometimes. In oxygen annealing at 700 deg. C, grain boundaries were considered not to be pinned at the surface, mixture diffusion was main mechanism in growth of oxide. Compression stress development in whole film led to extrusion of grains that was the reason that multiple appearances such as pyramid-like and nutshell-like morphology formed
FFTF fuel pin design bases and performance
International Nuclear Information System (INIS)
Cox, C.M.; Hanson, J.E.; Roake, W.E.; Slember, R.J.; Weber, C.E.; Millunzi, A.C.
1975-04-01
The FFTF fuel pin was conservatively designed to meet thermal and structural performance requirements in the categories normal operation, upset events, emergency events, and hypothetical, faulted events. The fuel pin operating limits consistent with these requirements were developed from a strong fuel pin irradiation testing program scoped to define the performance capability under relevant steady state and transient conditions. Comparison of the results of the irradiation testing program with design requirements indicates that the FFTF fuel pin can exceed its goal burnup of 80,000 MWd/MTM. (U.S.)
Ferromagnetic artificial pinning centers in multifilamentary superconducting wires
International Nuclear Information System (INIS)
Wang, J.Q.; Rizzo, N.D.; Prober, D.E.
1997-01-01
The authors fabricated multifilamentary NbTi wires with ferromagnetic (FM) artificial pinning centers (APCs) to enhance the critical current density (J c ) in magnetic fields. They used a bundle and draw technique to process the APC wires with either Ni or Fe as the pinning centers. Both wires produced higher J c in the high field range (5-9 T) than previous non-magnetic APC wires similarly processed, even though the authors have not yet optimized pin percentage. Using a magnetometer they found that the pins remained ferromagnetic for the wires with maximum J c . However, they did observe a substantial loss of FM material for the wires where the pin diameter approached 3 nm. Thus, they expect further enhancement of J c with better pin quality
Su, Housheng
2013-01-01
Synchronization, consensus and flocking are ubiquitous requirements in networked systems. Pinning Control of Complex Networked Systems investigates these requirements by using the pinning control strategy, which aims to control the whole dynamical network with huge numbers of nodes by imposing controllers for only a fraction of the nodes. As the direct control of every node in a dynamical network with huge numbers of nodes might be impossible or unnecessary, it’s then very important to use the pinning control strategy for the synchronization of complex dynamical networks. The research on pinning control strategy in consensus and flocking of multi-agent systems can not only help us to better understand the mechanisms of natural collective phenomena, but also benefit applications in mobile sensor/robot networks. This book offers a valuable resource for researchers and engineers working in the fields of control theory and control engineering. Housheng Su is an Associate Professor at the Department of Contro...
Zr, Hf, Mo and W-containing oxide phases as pinning additives in Bi-2212 superconductor
International Nuclear Information System (INIS)
Makarova, M.V.; Kazin, P.E.; Tretyakov, Yu.D.; Jansen, M.; Reissner, M.; Steiner, W.
2005-01-01
Phase formation was investigated in Bi-Sr-Ca-Cu-M-O (M = Mo, W) systems at 850-900 deg C. It was found that Sr 2 CaMO 6 phases were chemically compatible with Bi-2212. The composites Bi-2212-Sr 2 CaMO 6 and Bi-2212-SrAO 3 (A = Zr, Hf) were obtained from a sol-gel precursor using crystallisation from the melt. The materials consisted of Bi-2212 matrix and submicron or micron grains of the corresponding dispersed phase. T c was equal or exceeded that for undoped Bi-2212, reaching T c = 97 K in the Mo-containing composite. The composites exhibited enhanced pinning in comparison with similar prepared pure Bi-2212, especially at T = 60 K. The best pinning parameters were observed for the Bi-2212-Sr 2 CaWO 6 composite
Said, Marwa M; Azab, Samar S; Saeed, Noha M; El-Demerdash, Ebtehal
2018-03-01
The present study aimed to elucidate the potential antifibrotic effects of pinocembrin (PIN), a flavanone found abundantly in honey and propolis, by studying its effect on different oxidative stress, inflammatory and fibrosis markers in an experimental model of CCl4-induced liver fibrosis. PIN (20 mg/kg) was given orally 3 times/week for 6 consecutive weeks alternating with CCl4 (0.5 mL/kg, 1:1 mixture with corn oil, i. p.) twice weekly. Different hepatotoxicity indices, oxidative stress, inflammatory and liver fibrosis markers were assessed. PIN significantly restored liver transaminases and total cholesterol to normal levels. Also, PIN ameliorated oxidative stress injury evoked by CCl4 as evidenced by inhibition of reduced glutathione depletion and lipid peroxidation as well as elevation of antioxidant enzyme superoxide dismutase (SOD). Further, PIN upregulated the nuclear factor erythroid 2 (NF-E2)-related factor 2 (Nrf2), thereby inducing the expression and activity of the cytoprotective enzyme hemeoxygenase-1 (HO-1). Moreover, PIN alleviated pro-inflammatory cytokines such as TNF-α via inhibiting nuclear factor-κB (NF-κB) activation. As markers of fibrosis, collagen and α-SMA expression increased markedly in the CCl4 group and PIN prevented these alterations. In addition, PIN down-regulated TGFβ1 and p-Smad2/3, thereby inhibiting TGFβ1/Smad signaling pathway. These results suggest that PIN possess potent antifibrotic effects that can be explained on its antioxidant properties. It ameliorates oxidative stress and inflammation during induction of fibrogenesis via its ability to augment celular antioxidant defenses, activating Nrf2-mediated HO-1 expression and modulating NF-κB and TGF-β1/Smad signaling pathway.
Nano-engineered pinning centres in YBCO superconducting films
Energy Technology Data Exchange (ETDEWEB)
Crisan, A., E-mail: adrian.crisan@infim.ro [National Institute for Materials Physics Bucharest, 105 bis Atomistilor Str., 077125 Magurele (Romania); School of Metallurgy and Materials, University of Birmingham, Edgbaston, B15 2TT Birmingham (United Kingdom); Dang, V.S. [School of Metallurgy and Materials, University of Birmingham, Edgbaston, B15 2TT Birmingham (United Kingdom); Nano and Energy Center, VNU Hanoi University of Science, 334 Nguyen Trai, Thanh Xuan, Hanoi (Viet Nam); Mikheenko, P. [School of Metallurgy and Materials, University of Birmingham, Edgbaston, B15 2TT Birmingham (United Kingdom); Department of Physics, University of Oslo, P.O. Box 1048 Blindern, N-0316 Oslo (Norway)
2017-02-15
Highlights: • Power applications of YBCO films/coated conductors in technological relevant magnetic fields requires nano-engineered pinning centre. • Three approaches have been proposed: substrate decoration, quasi-multilayers, and targets with secondary phase nano-inclusions. • Combination of all three approaches greatly increased critical current in YBCO films. • Bulk pinning force, pinning potential, and critical current density are estimated and discussed in relation with the type and strength of pinning centres related to the defects evidenced by Transmission Electron Microscopy. - Abstract: For practical applications of superconducting materials in applied magnetic fields, artificial pinning centres in addition to natural ones are required to oppose the Lorentz force. These pinning centres are actually various types of defects in the superconductor matrix. The pinning centres can be categorised on their dimension (volume, surface or point) and on their character (normal cores or Δκ cores). Different samples have been produced by Pulsed Laser Deposition, with various thicknesses, temperatures and nanostructured additions to the superconducting matrix. They have been characterized by SQUID Magnetic Properties Measurement System and Physical Properties Measurement System, as well as by Transmission Electron Microscopy (TEM). Correlations between pinning architecture, TEM images, and critical currents at various fields and field orientations will be shown for a large number of YBa{sub 2}Cu{sub 3}O{sub x} films with various types and architectures of artificial pinning centres.
Directory of Open Access Journals (Sweden)
Kaijie Xu
2016-03-01
Full Text Available Abstract Switchgrass (Panicum virgatum L.; family Poaceae is a warm-season C4 perennial grass. Tillering plays an important role in determining the morphology of aboveground parts and the final biomass yield of switchgrass. Auxin distribution in plants can affect a variety of important growth and developmental processes, including the regulation of shoot and root branching, plant resistance and biological yield. Auxin transport and gradients in plants are mediated by influx and efflux carriers. PvPIN1, a switchgrass PIN1-like gene that is involved in regulating polar transport, is a putative auxin efflux carrier. Neighbor-joining analysis using sequences deposited in NCBI databases showed that the PvPIN1gene belongs to the PIN1 family and is evolutionarily closer to the Oryza sativa japonica group. Tiller emergence and development was significantly promoted in plants subjected toPvPIN1 RNA interference (RNAi, which yielded a phenotype similar to that of wild-type plants treated with the auxin transport inhibitor TIBA (2,3,5-triiodobenzoic acid. A transgenic approach that inducedPvPIN1 gene overexpression or suppression altered tiller number and the shoot/root ratio. These data suggest that PvPIN1plays an important role in auxin-dependent adventitious root emergence and tillering.
Shan, Hangying; Xiao, Jun; Chu, Qiyi
2018-05-01
The Z-Pin interfacial bond properties play an important role in the structural performance of X-Cor® sandwich structures. This paper presents an experimental investigation on bond-slip behavior of Z-Pin interfaces using Z-Pin pull-out test. Based on the experimental data the whole Z-Pin pull-out process consists of three stages: initial bonding, debonding and frictional sliding. Comparative experimental study on the influence of design parameters on bond-slip behavior of Z-Pin interfaces has also been performed. Numerical analyses were conducted with the ABAQUS finite element (FE) program to simulate the Z-Pins bond-slip response of the pull-out test. The Z-Pins interfacial bond-slip behavior was implemented using nonlinear spring elements characterized with the constitutive relation from experimental results. Numerical results were validated by comparison with experimental data, and reasonably good agreement was achieved between experimental and analytical pull-out force-slip curves.
Energy Technology Data Exchange (ETDEWEB)
De Matteis, Massimo [Azienda Ospedaliera Policlinico S. Orsola-Malpighi, Bologna (Italy). UO Radiologia Albertoni; Poggi, Cristina; De Martino, Antonietta; Pavlica, Pietro [Azienda Ospedaliera Policlinico S. Orsola-Malpighi, Bologna (Italy). UO Radiologia Palagi, Dipartimento area radiologica; Corti, Barbara [Azienda Ospedaliera Policlinico S. Orsola-Malpighi, Bologna (Italy). UO Anatomia ed istologia patologica, Dipartimento oncologico ed ematologico; Barozzi, Libero [Azienda Ospedaliera Policlinico S. Orsola-Malpighi, Bologna (Italy). UO Radiologia d' urgenza, Dipartimento emergenze ed accettazione
2005-09-15
Purpose. Prostatic intra-epithelial neoplasia (PIN) is considered a pre-malignant lesion and the main precursor of invasive prostatic adenocarcinoma. A PIN diagnosis established by prostate needle biopsy poses a difficult clinical management. problem. We retrospectively reviewed our three-year experience in order to identify criteria for referring patients to repeat biopsy. Materials and methods. We reviewed the repeat biopsy records of 72 patients in whom PIN had been detected on initial US-guided needle biopsy of the prostate. All the patients had a minimum of 6 biopsy cores taken, and they all had PSA > 4 ng/ml. Results. Adenocarcinoma was detected in 15 patients out of 50 (30%) with an initial diagnosis of low-grade PIN and in 10 patients out of 22 (45.4%) with high grade PIN, in 7 out of 18 (39%) in whom PSA levels had decreased during the observation interval, in 16 patients out of 46 (35%) in whom the PSA had increased and in 2 patients out of 8 (25%) with stable PSA. Conclusions. Our results seem to confirm that PIN can be considered a precursor of prostatic adenocarcinoma or a histological alteration often associated with it. Patients with low-grade PIN and particularly those with high-grade PIN should be regularly subjected to repeat biopsy at short intervals due to the high frequency of the final diagnosis of carcinoma. No agreement has been reached on the time interval between the first and the second biopsy. The PSA changes during the observation period are not a statistically significant parameter to suggest the repetition of prostatic biopsy. [Italian] Scopo. La neoplasia prostatica intraepiteliale (PIN) e considerata una lesione premaligna ed il precursore principale dell'adenocarcinoma prostatico infiltrante. La diagnosi di PIN ottenuta con l'agobiopsia della prostata rappresenta un difficile problema gestionale clinico. In una valutazione retrospettiva della nostra esperienza di 3 anni si e cercato di individuare i criteri che possano
Vortex pinning and creep experiments
International Nuclear Information System (INIS)
Kes, P.H.
1991-01-01
A brief review of basic flux-pinning and flux-creep ingredients and a selection of experimental results on high-temperature-superconductivity compounds is presented. Emphasis is put on recent results and on those properties which are central to the emerging understanding of the flux-pinning and flux-creep mechanisms of these fascinating materials
Breached fuel pin contamination from Run Beyond Cladding Breach (RBCB) tests in EBR-II
International Nuclear Information System (INIS)
Colburn, R.P.; Strain, R.V.; Lambert, J.D.B.; Ukai, S.; Shibahara, I.
1988-09-01
Studies indicate there may be a large economic incentive to permit some continued reactor operation with breached fuel pin cladding. A major concern for this type of operation is the potential spread of contamination in the primary coolant system and its impact on plant maintenance. A study of the release and transport of contamination from naturally breached mixed oxide Liquid Metal Reactor (LMR) fuel pins was performed as part of the US Department of Energy/Power Reactor and Nuclear Fuel Development Corporation (DOE/PNC) Run Beyond Cladding Breach (RBCB) Program at EBR-II. The measurements were made using the Breached Fuel Test Facility (BFTF) at EBR-II with replaceable deposition samplers located approximately 1.5 meters from the breached fuel test assemblies. The effluent from the test assemblies containing the breached fuel pins was routed up through the samplers and past dedicated instrumentation in the BFTF before mixing with the main coolant flow stream. This paper discusses the first three contamination tests in this program. 2 refs., 5 figs., 2 tabs
Nuclear fuel pin controlled failure device
International Nuclear Information System (INIS)
Schlenker, L.D.
1975-01-01
Each fuel pin of a fuel assembly for a water-cooled nuclear reactor is provided with means for rupturing the cladding tube at a predetermined location if an abnormal increase in pressure of the gases present occurs due to a loss-of-coolant accident. Preferably all such rupture means are oriented to minimize the hydraulic resistance to the flow of emergency core coolant such as all rupture means pointing in the same direction. Rupture means may be disposed at different elevations in adjacent fuel pins and, further, fuel pins may be provided with two or more rupture means, one of which is in the upper portion of the fuel pin. Rupture means are mechanical as by providing a locally weakened condition of a controlled nature in the cladding. (U.S.)
The pin pixel detector--X-ray imaging
Bateman, J E; Derbyshire, G E; Duxbury, D M; Marsh, A S; Simmons, J E; Stephenson, R
2002-01-01
The development and testing of a soft X-ray gas pixel detector, which uses connector pins for the anodes is reported. Based on a commercial 100 pin connector block, a prototype detector of aperture 25.4 mm centre dot 25.4 mm can be economically fabricated. The individual pin anodes all show the expected characteristics of small gas detectors capable of counting rates reaching 1 MHz per pin. A 2-dimensional resistive divide readout system has been developed to permit the imaging properties of the detector to be explored in advance of true pixel readout electronics.
International Nuclear Information System (INIS)
Wang, Chenggong; Irfan, Irfan; Turinske, Alexander J.; Gao, Yongli
2012-01-01
The electronic structure evolution of interfaces of fullerene (C 60 ) with copper phthalocyanine (CuPc) on highly oriented pyrolitic graphite (HOPG) and on native silicon oxide has been investigated with ultra-violet photoemission spectroscopy and inverse photoemission spectroscopy. The lowest unoccupied molecular orbital edge of C 60 was found to be pinned at the interface with CuPc on SiO 2 . A substantial difference in the electron affinity of CuPc on the two substrates was observed as the orientation of CuPc is lying flat on HOPG and standing up on SiO 2 . The ionization potential and electron affinity of C 60 were not affected by the orientation of CuPc due to the spherical symmetry of C 60 molecules. We observed band bending in C 60 on the standing-up orientation of CuPc molecules, while the energy levels of C 60 on the flat lying orientation of CuPc molecules were observed to be flat. - Highlights: ► Orientation of copper phthalocyanine (CuPc) on ordered graphite and silicon oxide. ► Pinning of lowest unoccupied molecular orbital edge of C60 to the Fermi level on CuPc. ► No C60 pinning or band bending was observed on flat laying CuPc. ► Results are useful for organic photovoltaic and organic light emitting diode research.
A thermodynamic model for the attack behaviour in stainless steel clad oxide fuel pins
International Nuclear Information System (INIS)
Goetzmann, O.
1979-01-01
So far, post irradiation examination of burnt fuel pins has not revealed a clear cut picture of the cladding attack situation. For seemingly same conditions sometimes attack occurs, sometimes not. This model tries to depict the reaction possibilities along the inner cladding wall on the basis of thermodynamic facts in the fuel pin. It shows how the thermodynamic driving force for attack changes along the fuel column, and with different initial and operational conditions. Two criteria for attack are postulated: attack as a result of the direct reaction of reactive elements with cladding components; and attack as a result of the action of a special agent (CsOH). In defining a reaction potenial the oxygen potential, the temperature conditions (cladding temperature and fuel surface temperature), and the fission products are involved. For the determination of the oxygen potential at the cladding, three models for the redistribution of oxygen across the fuel/clad gap are offered. The effect of various parameters, like rod power, gap conductance, oxygen potential, inner wall temperature, on the thermodynamic potential for attack is analysed. (Auth.)
Heat transfer in a fuel pin shipping container
International Nuclear Information System (INIS)
Ingham, J.G.
1980-01-01
Maximum cladding temperatures occur when the IDENT 1578 fuel pin shipping container is installed in the T-3 Cask. The maximum allowable cladding temperature of 800 0 F is reached when the rate of energy deposited in the 19-pin basket reaches 400 watts. Since 45% of the energy which is generated in the fuel escapes the 19-pin basket without being deposited, mostly gamma energy, the maximum allowable rate of heat generation is 400/.55 = 727 watts. Similarly, the maximum allowable cladding temperature of 800 0 F is reached when the rate of energy deposited in the 40-pin basket reaches 465 watts. Since 33% of the energy which is generated in the fuel escapes the 40-pin basket without being deposited, mostly gamma energy, the maximum allowable rate of heat generation is 465/.66 = 704 watts. The IDENT 1578 fuel pin shipping container therefore meets its thermal design criteria. IDENT 1578 can handle fuel pins with a decay heat load of 600 watts while maintaining the maximum fuel pin cladding temperature below 800 0 F. The emissivities which were determined from the test results for the basket tubes and container are relatively low and correspond to new, shiny conditions. As the IDENT 1578 container is exposed to high temperatures for extended periods of time during the transportation of fuel pins, the emissivities will probably increase. This will result in reduced temperatures
Electro-optical fuel pin identification system
International Nuclear Information System (INIS)
Kirchner, T.L.
1978-09-01
A prototype Electro-Optical Fuel Pin Identification System referred to as the Fuel Pin Identification System (FPIS) has been developed by the Hanford Engineering Development Laboratory (HEDL) in support of the Fast Flux Test Facility (FFTF) presently under construction at HEDL. The system is designed to remotely read an alpha-numeric identification number that is roll stamped on the top of the fuel pin end cap. The prototype FPIS consists of four major subassemblies: optical read head, digital compression electronics, video display, and line printer
Analisis Sektor/Sub Sektor Unggulan di Kabupaten Bungo
Directory of Open Access Journals (Sweden)
Gafur Gafur
2016-03-01
Full Text Available Abstract. This study aimed to analyze the leading sectors in Bungo. The method used is Location Quotient (LQ, Dynamic Location Quotient (DLQ, specialization index, Growth Ratio Model (MRP. Based on analysis of LQ and DLQ, there are only two basis sectors at present and in the future, namely the construction sector and trade, hotels and restaurants. Based on the analysis of Specialization Index, in Bungo Regency has a concentration of the economy in the agricultural sector and the manufacturing sector. Based on MRP analysis also showed that prominent sector growth at the level of Bungo and Jambi Province, namely electricity, gas and water supply; the building sector; and trade, hotels and restaurants. Keywords : Location Quotient (LQ, Dinamic Location Quotient (DLQ, Specialization Index, Growth Ratio Model Abstrak. Penelitian ini bertujuan untuk menganalisis sektor unggulan di Kabupaten Bungo. Metode yang digunakan adalah analisis Location Quotient (LQ, Dinamic Location Quotient (DLQ, indeks spesialisasi, Model Rasio Pertumbuhan (MRP. Berdasarkan analisis LQ dan DLQ, hanya ada 2 sektor yang menjadi sektor basis pada saat ini dan pada masa yang akan datang yaitu sektor bangunan dan sektor perdagangan, hotel dan restoran. Berdasarkan analisis Indeks Spesialisasi, di Kabupaten Bungo telah terjadi konsentrasi ekonomi pada sektor pertanian dan sektor industri pengolahan. Berdasarkan analisis MRP juga dapat diketahui bahwa sektor yang menonjol pertumbuhannya pada tingkat Kabupaten Bungo dan Provinsi Jambi yaitu sektor listrik, gas dan air bersih; sektor bangunan; serta sektor perdagangan, hotel dan restoran. Kata Kunci : Location Quotient (LQ, Dinamic Location Quotient (DLQ, indeks spesialisasi, Model Rasio Pertumbuhan
Directory of Open Access Journals (Sweden)
Ernestina Rahmanasari
2013-09-01
Full Text Available Transaksi keuangan badan pemerintahan tingkat daerah dipertanggungjawabkan kepada Kementrian Keuangan melalui Kantor Pelayanan Perbendaharaan Negara (KPPNsetiap bulan dalam bentuk Laporan Keuangan Pemerintah Pusat (LKPP. Laporan Keuangan, didukung dengan teknologi Business Intelligence(BI dashboarddapat dimanfaatkan sebagai data-driven decision support system yang mendorong performa kinerja. Analisis dan desainterhadap pembuatan BI dashboard menunjukkanbagaimana Laporan Keuangan dapat digunakan untuk monitoring realisasi penyerapan dana DIPA dan kinerja instansi secara tepat waktu dan interaktif.Analisis terdiri dari analisis Indikator Kinerja Utama (IKU dan analisis Laporan Keuangan. IKUpada analisis dan desain ini mencakup ketercapaian estimasi dengan penerimaan, ketercapaian pagu dengan belanja, ketepatan waktu pengiriman rekonsiliasi oleh instansi, validasi, akurasi, dan ketepatan data. Desain terdiri dari katalog dashboard, alur analisis, sumber data, desain User-Interface, dan desain objek dashboard. Sedangkan dashboard yang dirancang menggunakan aplikasi Vera sebagai Enterprise System, mengakses basis data MySQL, dan menampilkan data dengan teknologi data-driven business-intelligence Qlikview. Desain aplikasi yang telah dibuat akan menampilkan 4 (empat Tab yaitu: Dashboard utama, Analisis, Monitoring, dan Laporan
Semiotika Teks: Sebuah Pendekatan Analisis Teks
Directory of Open Access Journals (Sweden)
Yasraf Amir Piliang
2004-12-01
tanda-tanda yang membentuk apa yang disebut sebagai ‘teks’. Analisis teks, menurut Roland Barthes, akan menghasilkan makna denotatif, yakni makna tanda yang bersifat eksplisit, dan makna konotatif, yaitu makna tanda lapis kedua yang bersifat implisit.
Radon measurements with a PIN photodiode
International Nuclear Information System (INIS)
Martin-Martin, A.; Gutierrez-Villanueva, J.L.; Munoz, J.M.; Garcia-Talavera, M.; Adamiec, G.; Iniguez, M.P.
2006-01-01
Silicon photodiodes are well suited to detect alphas coming from different sources as neutron reactions or radon daughters. In this work a radon in air detecting device, using an 18x18 mm silicon PIN photodiode is studied. The ionized airborne decay products formed during radon diffusion were focused by an accelerating high voltage to the PIN surface. Several conducting rings were disposed inside a cylindrical PVC vessel in such a way that they reproduced the electric field created by a punctual charge located behind PIN position. Alpha spectra coming from the neutral and ionized species deposited on the PIN surface, dominated by 218 Po and 214 Po progeny peaks, were recorded for varying conditions. Those include radon concentration from a Pylon source, high voltage (thousands of volts) and PIN inverse bias voltage. Different parameters such as temperature and humidity were also registered during data acquisition. The increase in the particle collection efficiency with respect to zero electric field was compared with the corresponding to a parallel plates configuration. A discussion is made in terms of the most appropriate voltages for different radon concentrations
Microfinanza: analisi d’impatto di un programma in India
Directory of Open Access Journals (Sweden)
Tommaso Rondinella
2005-03-01
Full Text Available L’analisi d’impatto dei programmi di microfinanza è uno strumento utile sia per migliorare i servizi offerti sia per garantire ai donatori che il denaro concesso sia utilizzato per programmi efficaci nell’alleviare la povertà. Il presente lavoro è costituito da due parti: la prima è dedicata all’analisi d’impatto, la seconda all’analisi empirica sul campo. L’indagine è stata condotta attraverso l’utilizzo di uno strumento in grado di dare una indicazione chiara dei cambiamenti avvenuti nelle condizioni di vita dei beneficiari e con il pregio di essere applicabile a costi molto ridotti. I risultati ottenuti mostrano in che misura l’accesso al credito cambi le condizioni di vita dei più poveri inducendo consistenti aumenti del reddito familiare, dei risparmi, della diversificazione delle attività produttive e del consumo di cibo. Inoltre si osserva, all’interno dei nuclei familiari, un miglioramento della condizione femminile chiaramente dipendente dalla partecipazione al programma di microcredito
Fabrication of FFTF fuel pin wire wrap
International Nuclear Information System (INIS)
Epperson, E.M.
1980-06-01
Lateral spacing between FFTF fuel pins is required to provide a passageway for the sodium coolant to flow over each pin to remove heat generated by the fission process. This spacing is provided by wrapping each fuel pin with type 316 stainless steel wire. This wire has a 1.435mm (0.0565 in.) to 1.448mm (0.0570 in.) diameter, contains 17 +- 2% cold work and was fabricated and tested to exacting RDT Standards. About 500 kg (1100 lbs) or 39 Km (24 miles) of fuel pin wrap wire is used in each core loading. Fabrication procedures and quality assurance tests are described
Pinning impulsive synchronization of stochastic delayed coupled networks
International Nuclear Information System (INIS)
Tang Yang; Fang Jian-An; Wong W K; Miao Qing-Ying
2011-01-01
In this paper, the pinning synchronization problem of stochastic delayed complex network (SDCN) is investigated by using a novel hybrid pinning controller. The proposed hybrid pinning controller is composed of adaptive controller and impulsive controller, where the two controllers are both added to a fraction of nodes in the network. Using the Lyapunov stability theory and the novel hybrid pinning controller, some sufficient conditions are derived for the exponential synchronization of such dynamical networks in mean square. Two numerical simulation examples are provided to verify the effectiveness of the proposed approach. The simulation results show that the proposed control scheme has a fast convergence rate compared with the conventional adaptive pinning method. (general)
ANALISIS KINERJA KEUANGAN PERUSAHAAN PT. ASURANSI JIWASRAYA (PERSERO) CABANG SULAWESI SELATAN
ARIANTY, ASTRI
2012-01-01
ANALISIS KINERJA KEUANGAN PERUSAHAAN PT. ASURANSI JIWASRAYA (PERSERO) CABANG SULAWESI SELATAN COMPANY FINANCIAL PERFORMANCE ANALYSIS PT. INSURANCE JIWASRAYA (LIMITED) SOUTH BRANCH SULAWESI Astri Arianty Prof. Dr. H. Muhammad Ali, SE., M.S Drs. Armayah Sida, M.Si Analisis terhadap kinerja keuangan perusahaan sangat penting dilakukan untuk mengetahui sejauh mana tingkat pencapaian yang telah diperoleh perusahaan sebagaimana tujuan perusahaan dalam menjalankan proses produk...
Pin-wise Reactor Analysis Based on the Generalized Equivalence Theory
Energy Technology Data Exchange (ETDEWEB)
Yu, Hwan Yeal; Heo, Woong; Kim, Yong Hee [KAIST, Daejeon (Korea, Republic of)
2016-05-15
In this paper, a pin-wise reactor analysis is performed based on the generalized equivalence theory. From the conventional fuel assembly lattice calculations, pin-wise 2-group cross sections and pin DFs are generated. Based on the numerical results on a small PWR benchmark, it is observed that the pin-wise core analysis provide quite accurate prediction on the effective multiplication factor and the peak pin power error is bounded by about 3% in peripheral fuel assemblies facing the baffle-reflector. Also, it was found that relatively large pin power errors occur along the interface between clearly different fuel assemblies. It is expected that the GET-based pin-by-pin core calculation can be further developed as an advanced method for reactor analysis via improving the group constants and discontinuity factors. Recently, high-fidelity multi-dimensional analysis tools are gaining more attention because of their accurate prediction of local parameters for core design and safety assessment. In terms of accuracy, direct whole-core transport is quite promising. However, it is clear that it is still very costly in terms of the computing time and memory requirements. Another possible solution is the pin-by-pin core analysis in which only small fuel pins are homogenized and the 3-D core analysis is still performed using a low-order operator such as the diffusion theory. In this paper, a pin-by-pin core analysis is performed using the hybrid CMFD (HCMFD) method. Hybrid CMFD is a new global-local iteration method that has been developed for efficient parallel calculation of pinby-pin heterogeneous core analysis. For the HCMFD method, the one-node CMFD scheme is combined with a local two-node CMFD method in a non-linear way. Since the SPH method is iterative and SPH factors are not direction dependent, it is clear that SPH method takes more computing cost and cannot take into account the different heterogeneity and transport effects at each pin interface. Unlike the SPH
Pinning impulsive control algorithms for complex network
Energy Technology Data Exchange (ETDEWEB)
Sun, Wen [School of Information and Mathematics, Yangtze University, Jingzhou 434023 (China); Lü, Jinhu [Academy of Mathematics and Systems Science, Chinese Academy of Sciences, Beijing 100190 (China); Chen, Shihua [College of Mathematics and Statistics, Wuhan University, Wuhan 430072 (China); Yu, Xinghuo [School of Electrical and Computer Engineering, RMIT University, Melbourne VIC 3001 (Australia)
2014-03-15
In this paper, we further investigate the synchronization of complex dynamical network via pinning control in which a selection of nodes are controlled at discrete times. Different from most existing work, the pinning control algorithms utilize only the impulsive signals at discrete time instants, which may greatly improve the communication channel efficiency and reduce control cost. Two classes of algorithms are designed, one for strongly connected complex network and another for non-strongly connected complex network. It is suggested that in the strongly connected network with suitable coupling strength, a single controller at any one of the network's nodes can always pin the network to its homogeneous solution. In the non-strongly connected case, the location and minimum number of nodes needed to pin the network are determined by the Frobenius normal form of the coupling matrix. In addition, the coupling matrix is not necessarily symmetric or irreducible. Illustrative examples are then given to validate the proposed pinning impulsive control algorithms.
Pinning impulsive control algorithms for complex network
International Nuclear Information System (INIS)
Sun, Wen; Lü, Jinhu; Chen, Shihua; Yu, Xinghuo
2014-01-01
In this paper, we further investigate the synchronization of complex dynamical network via pinning control in which a selection of nodes are controlled at discrete times. Different from most existing work, the pinning control algorithms utilize only the impulsive signals at discrete time instants, which may greatly improve the communication channel efficiency and reduce control cost. Two classes of algorithms are designed, one for strongly connected complex network and another for non-strongly connected complex network. It is suggested that in the strongly connected network with suitable coupling strength, a single controller at any one of the network's nodes can always pin the network to its homogeneous solution. In the non-strongly connected case, the location and minimum number of nodes needed to pin the network are determined by the Frobenius normal form of the coupling matrix. In addition, the coupling matrix is not necessarily symmetric or irreducible. Illustrative examples are then given to validate the proposed pinning impulsive control algorithms
Vortex pinning landscape in MOD-TFA YBCO nanostroctured films
Gutierrez, J.; Puig, T.; Pomar, A.; Obradors, X.
2008-03-01
A methodology of general validity to study vortex pinning in YBCO based on Jc transport measurements is described. It permits to identify, separate and quantify three basic vortex pinning contributions associated to anisotropic-strong, isotropic-strong and isotropic-weak pinning centers. Thereof, the corresponding vortex pinning phase diagrams are built up. This methodology is applied to the new solution-derived YBCO nanostructured films, including controlled interfacial pinning by the growth of nanostructured templates by means of self-assembled processes [1] and YBCO-BaZrO3 nanocomposites prepared by modified solution precursors. The application of the methodology and comparison with a standard solution-derived YBCO film [2], enables us to identify the nature and the effect of the additional pinning centers induced. The nanostructured templates films show c-axis pinning strongly increased, controlling most of the pinning phase diagram. On the other hand, the nanocomposites have achieved so far, the highest pinning properties in HTc-superconductors [3], being the isotropic-strong defects contribution the origin of their unique properties. [1] M. Gibert et al, Adv. Mat. vol 19, p. 3937 (2007) [2] Puig.T et al, SuST EUCAS 2007 (to be published) [3] J. Gutierrez et al, Nat. Mat. vol. 6, p. 367 (2007) * Work supported by HIPERCHEM, NANOARTIS and MAT2005-02047
Vortex pinning by point defect in superconductors
International Nuclear Information System (INIS)
Liao Hongyin; Zhou Shiping; Du Haochen
2003-01-01
We apply the periodic time-dependent Ginzburg-Landau model to study vortex distribution in type-II superconductors with a point-like defect and square pinning array. A defect site will pin vortices, and a periodic pinning array with right geometric parameters, which can be any form designed in advance, shapes the vortex pattern as external magnetic field varies. The maximum length over which an attractive interaction between a pinning centre and a vortex extends is estimated to be about 6.0ξ. We also derive spatial distribution expressions for the order parameter, vector potential, magnetic field and supercurrent induced by a point defect. Theoretical results and numerical simulations are compared with each other and they are consistent
Directory of Open Access Journals (Sweden)
Nathanael August Zefanya
2017-01-01
Full Text Available Industri ban di Indonesia mengalami perkembangan pesat dalam kurun waktu 10 tahun terakhir. Namun, terjadinya krisis ekonomi global menjadi penyebab menurunnya pendapatan, salah satunya adalah PT MASA dengan produk utamanya yaitu ban mobil Achilles dan ban motor Corsa yang digunakan sebagai objek penelitian ini. Telah diilakukan analisis PESTEL dan Porter’s Five Forces, identifikasi faktor lingkungan internal dan eksternal dengan analisis SWOT serta merumuskan alternatif strategi bersaing untuk direkomendasikan kepada PT MASA. Perumusan strategi alternatif didapat dari hasil analisis Matriks BCG dan Matriks IE sebagai analisis portofolio untuk mendapatkan tema strategi alternatif dalam pembuatan Matriks SWOT. Strategi alternatif kemudian diperingkatkan dengan QSPM dan dilanjutkan pembuatan rencana aksi bagi PT MASA dalam waktu 5 tahun ke depan. Setelah dilakukan analisis industri, diketahui bahwa ancaman terbesar datang dari pesaing produsen ban. Dari hasil analisis portofolio, PT MASA berada di kuadran I karena memiliki koordinat IFE serta EFE 3,32 dan 3,26. Dari hasil analisis Matriks IE, PT MASA direkomendasikan untuk melakukan strategi grow and build. Hasil Matriks BCG menunjukkan bahwa Achilles berada di dogs, sementara Corsa berada di question marks. Terdapat 13 strategi alternatif hasil dari formulasi strategi dengan menggunakan matriks TOWS. Dari hasil analisis QSPM, terdapat 7 alternatif strategi terbaik dan rencana aksi..
Directory of Open Access Journals (Sweden)
Diana Puspita Sari
2012-02-01
Full Text Available PT Telkom memiliki misi untuk memberikan layanan One Stop Infocom dengan kualitas prima dan harga kompetitif. Kenyataannya, PT. Telkom Kandatel Semarang mengalami penurunan pendapatan. Semakin berkembangnya layanan jasa fixed wireless yang lebih mudah dan murah, menyebabkan penurunan pemakaian jasa fixed wireline. Dengan konsumen melakukan pembelian pertama pada suatu produk tertentu dengan harga terjangkau, kualitas terjamin, maka konsumen akan kembali membeli produk tersebut, dan dampaknya dari fenomena ini adalah kepuasan pelanggan (customer satisfaction terhadap produk tertentu karena telah memberikan kepuasan dan terjaminnya kualitas, walaupun banyak pesaing lain. Oleh sebab itu, penelitian ini membahas dan melakukan analisis kepuasan pelanggan fixed wireline PT. Telkom Kandatel Semarang, menggunakan variabel kepuasan pelanggan untuk dikelompokkan menjadi tiga tingkatan yaitu pelanggan yang sangat puas, puas, dan tidak puas dengan menggunakan analisis klaster, kemudian dilakukan analisis variabel 4P Customer Relationship Management (CRM menggunakan analisis diskriminan, sehingga diketahui atribut yang mempengaruhi tingkat kepuasan pelanggan agar PT. Telkom Kandatel Semarang dapat terus mempertahankan dan meningkatkan kepuasan pelanggan dengan berusaha memenuhi kebutuhan dan keinginan pelanggan dengan maksud kepuasan pelanggan tidak menurun agar dapat meningkatkan intensitas pemakaian fixed wireline. Kata kunci : analisis klaster, analisis diskriminan, kepuasan pelanggan, fixed wireline PT Telkom has a mission to provide a One Stop Infocom services with excellent quality and competitive price. In fact, PT. Telkom Semarang Kandatel income decreased. The growing fixed wireless service is easier and cheaper, causes a decrease in the use of fixed wireline services.With the first consumer purchase a given product at an affordable price, guaranteed quality, then consumers will buy the product again, and the impact of this phenomenon is
Inscuteable Regulates the Pins-Mud Spindle Orientation Pathway
Mauser, Jonathon F.; Prehoda, Kenneth E.
2012-01-01
During asymmetric cell division, alignment of the mitotic spindle with the cell polarity axis ensures that the cleavage furrow separates fate determinants into distinct daughter cells. The protein Inscuteable (Insc) is thought to link cell polarity and spindle positioning in diverse systems by binding the polarity protein Bazooka (Baz; aka Par-3) and the spindle orienting protein Partner of Inscuteable (Pins; mPins or LGN in mammals). Here we investigate the mechanism of spindle orientation by the Insc-Pins complex. Previously, we defined two Pins spindle orientation pathways: a complex with Mushroom body defect (Mud; NuMA in mammals) is required for full activity, whereas binding to Discs large (Dlg) is sufficient for partial activity. In the current study, we have examined the role of Inscuteable in mediating downstream Pins-mediated spindle orientation pathways. We find that the Insc-Pins complex requires Gαi for partial activity and that the complex specifically recruits Dlg but not Mud. In vitro competition experiments revealed that Insc and Mud compete for binding to the Pins TPR motifs, while Dlg can form a ternary complex with Insc-Pins. Our results suggest that Insc does not passively couple polarity and spindle orientation but preferentially inhibits the Mud pathway, while allowing the Dlg pathway to remain active. Insc-regulated complex assembly may ensure that the spindle is attached to the cortex (via Dlg) before activation of spindle pulling forces by Dynein/Dynactin (via Mud). PMID:22253744
Establishing the need for an engineering standard for agricultural hitch pins.
Deboy, G R; Knapp, W M; Field, W E; Krutz, G W; Corum, C L
2012-04-01
Documented incidents have occurred in which failure or unintentional disengagement of agricultural hitch pins has contributed to property damage and personal injury. An examination of current hitch pin use on a convenience sample of farm operations in Indiana revealed a variety of non-standard, worn and damaged, and inappropriately sized hitch pins in use. Informal interviews with the farm operators confirmed that hitch pin misuse, failure, or disengagement is a relatively widespread problem that remains largely unaddressed. On-site observations also suggested a low use of hitch pin retaining devices or safety chains. A review of prior research revealed that little attention has been given to this problem, and currently no documentation allows for an estimate of the frequency or severity of losses associated with hitch pin misuse, failure, or disengagement. No specific engineering standards were found that directly applied to the design, appropriate selection, or loading capacity of agricultural hitch pins. Major suppliers of replacement hitch pins currently provide little or no information on matching hitch pin size to intended applications, and most replacement hitch pins examined were of foreign origin, with the overwhelming majority imported from China or India. These replacement hitch pins provided no specifications other than diameter, length, and, in some cases, labeling that indicated that the pins had been "heat treated. " Testing of a sample of 11 commercially available replacement hitch pins found variation along the length of the pin shaft and between individual pins in surface hardness, a potential predictor of pin failure. Examination of 17 commercially available replacement pins also revealed a variety of identifiers used to describe pin composition and fabrication methods, e.g., "heat treated." None of the pins examined provided any specifications on loading capacity. It was therefore concluded that there is a need to develop an agricultural hitch
Roles of pinning strength and density in vortex melting
International Nuclear Information System (INIS)
Obaidat, I M; Khawaja, U Al; Benkraouda, M
2008-01-01
We have investigated the role of pinning strength and density on the equilibrium vortex-lattice to vortex-liquid phase transition under several applied magnetic fields. This study was conducted using a series of molecular dynamic simulations on several samples with different strengths and densities of pinning sites which are arranged in periodic square arrays. We have found a single solid-liquid vortex transition when the vortex filling factor n>1. We have found that, for fixed pinning densities and strengths, the melting temperature, T m , decreases almost linearly with increasing magnetic field. Our results provide direct numerical evidence for the significant role of both the strength and density of pinning centers on the position of the melting line. We have found that the vortex-lattice to vortex-liquid melting line shifts up as the pinning strength or the pinning density was increased. The effect on the melting line was found to be more pronounced at small values of strength and density of pinning sites
Neutron coincidence counter for MOX fuel pins in storage trays: users' manual
International Nuclear Information System (INIS)
Cowder, L.; Menlove, H.
1982-08-01
The neutron coincidence counter for measurement of mixed-oxide fuel pins in storage trays is described. The special detector head has been designed so that the detectors, high-voltage junction boxes, and electronics are interchangeable with those of the high-level neutron coincidence counter system. This manual describes the system components and the operation and maintenance of the counter. The counter was developed at Los Alamos National Laboratory for in-plant inspection applications by the International Atomic Energy Agency
Ultrasonic inspections of fuel alignment pins
International Nuclear Information System (INIS)
Rathgeb, W.; Schmid, R.
1994-01-01
As a remedy to the practical problem of defects in fuel alignment pins made of Inconel X750, an inspection technique has been developed which fully meets the requirements of detecting defects. The newly used fuel alignment pins made of austenite are easy to test and therefore satisfy the necessity of further inspections.For the fuel alignment pins of the upper core structure a safe and fast inspection technique was made available. The inspection sensitivity is high and it is possible to give quantitative directions concerning defect orientation and depth. After the required inspections had been concluded in 1989, a total of 18 inspections were carried out in various national and international nuclear power plants in the following years. During this time more than 6000 fuel alignment pines were examined.For the fuel alignment pins the inspection technique provided could increase the understanding of the defect process. This technique contributed to the development of an adaptive and economical repair strategy. ((orig.))
International Nuclear Information System (INIS)
Mikus, J.
2005-01-01
The purpose of this work consists in investigation of the WWER-440 control rod (CR) influence on space power distribution, especially from viewpoint of the values and gradient occurrence that could result in static and cyclic loads with some consequences, e.g. fuel pin bowing. As known, CR can cause power peaks in periphery fuel pins of adjacent operating assemblies because of the butt joint design of the absorbing adapter to the CR fuel part, that is, presence of the water cavity resulting in a flash up of thermal neutrons. As a consequence, beside well-known peaks in axial power distribution, above power gradients can occur inside of mentioned fuel pins. Because of complicated geometry and material composition of the CR, the detailed calculations concerning both above phenomena are complicated, too. Therefore it is useful to acquire appropriate experimental data to investigate mentioned influence and compare them with calculations. Since detailed power distributions cannot be obtained in the NPP, needed information is provided by means of experiments on research reactors. In case of measurements inside of fuel pins, special (e.g. track) detectors placed between fuel pellets are used. Such works are relatively complicated and time consuming, therefore an evaluation based on mathematical modelling and numerical approximation was proposed by means of that, and using measured power release in some selected fuel pins, information about power release inside of one of these fuel pins, can be obtained. For this purpose, an experiment on light water, zero-power research reactor LR-0 was realized and axial power distribution measurements were performed in a WWER-440 type core near to an authentic CR model. Application of the above evaluation method is demonstrated on one ''investigated'' fuel pin neighbouring CR by means of following results: 1. Axial power distribution inside of investigated fuel pin in two opposite positions on its pellets surface that are situated to
Cell homogenization methods for pin-by-pin core calculations tested in slab geometry
International Nuclear Information System (INIS)
Yamamoto, Akio; Kitamura, Yasunori; Yamane, Yoshihiro
2004-01-01
In this paper, performances of spatial homogenization methods for fuel or non-fuel cells are compared in slab geometry in order to facilitate pin-by-pin core calculations. Since the spatial homogenization methods were mainly developed for fuel assemblies, systematic study of their performance for the cell-level homogenization has not been carried out. Importance of cell-level homogenization is recently increasing since the pin-by-pin mesh core calculation in actual three-dimensional geometry, which is less approximate approach than current advanced nodal method, is getting feasible. Four homogenization methods were investigated in this paper; the flux-volume weighting, the generalized equivalence theory, the superhomogenization (SPH) method and the nonlinear iteration method. The last one, the nonlinear iteration method, was tested as the homogenization method for the first time. The calculations were carried out in simplified colorset assembly configurations of PWR, which are simulated by slab geometries, and homogenization performances were evaluated through comparison with the reference cell-heterogeneous calculations. The calculation results revealed that the generalized equivalence theory showed best performance. Though the nonlinear iteration method can significantly reduce homogenization error, its performance was not as good as that of the generalized equivalence theory. Through comparison of the results obtained by the generalized equivalence theory and the superhomogenization method, important byproduct was obtained; deficiency of the current superhomogenization method, which could be improved by incorporating the 'cell-level discontinuity factor between assemblies', was clarified
Pinning Synchronization of Switched Complex Dynamical Networks
Directory of Open Access Journals (Sweden)
Liming Du
2015-01-01
Full Text Available Network topology and node dynamics play a key role in forming synchronization of complex networks. Unfortunately there is no effective synchronization criterion for pinning synchronization of complex dynamical networks with switching topology. In this paper, pinning synchronization of complex dynamical networks with switching topology is studied. Two basic problems are considered: one is pinning synchronization of switched complex networks under arbitrary switching; the other is pinning synchronization of switched complex networks by design of switching when synchronization cannot achieved by using any individual connection topology alone. For the two problems, common Lyapunov function method and single Lyapunov function method are used respectively, some global synchronization criteria are proposed and the designed switching law is given. Finally, simulation results verify the validity of the results.
Breached-pin testing in the US
International Nuclear Information System (INIS)
Mahagin, D.E.; Lambert, J.D.B.
1981-04-01
Experience gained at EBR-II by the late 1970's from a significant number of failures in experimental fuel-pin irradiations forms the basis of a program directed towards the characterization of breached pins. The questions to be answered and the issues raised by further testing are discussed
Is magnetic pinning a dominant mechanism in Nb-Ti
International Nuclear Information System (INIS)
Cooley, L.D.; Lee, P.J.; Larbalestier, D.C.
1991-01-01
In this paper, the authors compare the pinning behavior of an artificial pinning center (APC) composite and a nanometer-filament Nb 46.5 wt% Ti composite to that of a conventional Nb 48 wt% Ti composite. The microstructure of the APC composite resembles the conventional composite, where ribbons of normal metal form the pinning centers, whereas the nanometer-filament composite has no internal normal metal but pins instead at the filament surface. The APC composite exhibits much stronger pinning relative to B c 2 than the conventional composite (21.4 GN/m 3 , 7 T vs. 18.9 GN/m 3 , 11 T), which is possibly due to the increased amount of pinning center (50 vol.% vs. 25 vol.%), however the proximity effect reduces the B c 2 unfavorably
Chanana, Mitin; Kumar, Adarsh; Tyagi, Som Prakash; Singla, Amit Kumar; Sharma, Arvind; Farooq, Uiase Bin
2018-02-01
The current study was undertaken to evaluate the clinical efficacy of end-threaded intramedullary pinning for management of various long bone fractures in canines. This study was conducted in two phases, managing 25 client-owned dogs presented with different fractures. The technique of application of end-threaded intramedullary pinning in long bone fractures was initially standardized in 6 clinical patients presented with long bone fractures. In this phase, end-threaded pins of different profiles, i.e., positive and negative, were used as the internal fixation technique. On the basis of results obtained from standardization phase, 19 client-owned dogs clinically presented with different fractures were implanted with end-threaded intramedullary positive profile screw ended self-tapping pin in the clinical application phase. The patients, allocated randomly in two groups, when evaluated postoperatively revealed slight pin migration in Group-I (negative profile), which resulted in disruption of callus site causing delayed union in one case and large callus formation in other two cases whereas no pin migration was observed in Group-II (positive profile). Other observations in Group-I was reduced muscle girth and delayed healing time as compared to Group-II. In clinical application, phase 21 st and 42 nd day post-operative radiographic follow-up revealed no pin migration in any of the cases, and there was no bone shortening or fragment collapse in end-threaded intramedullary positive profile screw ended self-tapping pin. The end-threaded intramedullary positive profile screw ended self-tapping pin used for fixation of long bone fractures in canines can resist pin migration, pin breakage, and all loads acting on the bone, i.e., compression, tension, bending, rotation, and shearing to an extent with no post-operative complications.
DEFF Research Database (Denmark)
Fausing, Bent
2012-01-01
This is about Pinterest, but with a different approach than usual to social networks. Pinterest is an image site par excellence. The images are as Windows that open outwards and also lets us look inwards and displays the soul and heart, the unintentional or pre-conscious desires. Happy Pinning!...
Suspension scheme for fuel pin
International Nuclear Information System (INIS)
Butts, C.E.; Gray, H.C.
1975-01-01
A description is presented of a nuclear fuel pin suspension arrangement comprising, in combination, a rod; a first beam member connected to said rod at one end; a plurality of parallel-spaced slidable fuel support plates attached to said first beam member, the longitudinal axis of first beam member being perpendicular to the longitudinal axis of each of said fuel support plates, a first coupling means disposed along the length of the first beam member for permitting slidable fuel support plates parallel movement with respect to the longitudinal axis of said first beam member, a second coupling means located at one end of each of slidable fuel plates for slidably engaging first coupling means of first beam member, a second beam member connected to the other end of each of parallel-spaced slidable fuel support plates and providing an extension, second beam member being provided with a third coupling means disposed along the length of second beam member at one end thereof; and a plurality of fuel pins provided with a fourth coupling means located at one end of each fuel pin for slidably engaging third coupling means of second beam member to permit each fuel pin parallel movement with respect to the longitudinal axis of second beam member. (U.S.)
Pembuatan Dan Analisis Exciter Generator Rf Untuk Siklotron Proton Decy-13
Prajitno, Prajitno
2011-01-01
PEMBUATAN DAN ANALISIS EXCITER GENERATOR RF UNTUK SIKLOTRON PROTON DECY-13.Telah dilakukan analisis dan pembuatan exciter generator RF untuk siklotron proton 13MeV. Generator RFakan digunakan sebagai sumber tegangan pemercepat bolak-Balik siklotron DECY-13 rancangan PTAPBBATAN.Berdasarkan dokumen rancangan dasar yang telah dibuat siklotron Decy-13 akan menggunakanmedan magnet 1,275 Tesla, sehingga frekuensi generator RF bila menggunakan harmonik keempat adalah77,667 MHz. Salah satu teknik pem...
Retractable Pin Tools for the Friction Stir Welding Process
1998-01-01
Two companies have successfully commercialized a specialized welding tool developed at the Marshall Space Flight Center (MSFC). Friction stir welding uses the high rotational speed of a tool and the resulting frictional heat created from contact to crush, 'stir' together, and forge a bond between two metal alloys. It has had a major drawback, reliance on a single-piece pin tool. The pin is slowly plunged into the joint between two materials to be welded and rotated as high speed. At the end of the weld, the single-piece pin tool is retracted and leaves a 'keyhole,' something which is unacceptable when welding cylindrical objects such as drums, pipes and storage tanks. Another drawback is the requirement for different-length pin tools when welding materials of varying thickness. An engineer at the MSFC helped design an automatic retractable pin tool that uses a computer-controlled motor to automatically retract the pin into the shoulder of the tool at the end of the weld, preventing keyholes. This design allows the pin angle and length to be adjusted for changes in material thickness and results in a smooth hole closure at the end of the weld. Benefits of friction stir welding, using the MSFC retractable pin tool technology, include the following: The ability to weld a wide range of alloys, including previously unweldable and composite materials; provision of twice the fatigue resistance of fusion welds and no keyholes; minimization of material distortion; no creation of hazards such as welding fumes, radiation, high voltage, liquid metals, or arcing; automatic retraction of the pin at the end of the weld; and maintaining full penetration of the pin.
Correlation of creep and swelling with fuel pin performance
International Nuclear Information System (INIS)
Jackson, R.J.; Washburn, D.F.; Garner, F.A.; Gilbert, E.R.
1975-09-01
The HEDL PNL-11 experiment described was one in a series of fueled subassemblies irradiated in EBR-II to demonstrate the adequacy of the FFTF fuel pin design. The cladding material, dimensions, and fuel density are prototypic of FFTF. Because neutron flux in EBR-II is lower than in FFTF, the uranium enrichment is higher in these experimental fuel pins, irradiated in EBR-II, than the FFTF enrichment for comparable linear heat rates. Some pertinent oprating conditions for the center fuel pin in this experiment are listed. This 37-pin subassembly represents, at 110,000 MWd/MTM, the highest burnup yet attained by a prototypic FFTF subassembly. Similarly, this is the highest fluence presently attained by prototypic fuel pins. A cladding breach occurred in one fuel pin which is presently being examined. Results are presented and discussed
Energy Technology Data Exchange (ETDEWEB)
E.H. Seabury
2013-09-01
Idaho National Laboratory’s (INL’s) Portable Isotopic Neutron Spectroscopy System (PINS) non-intrusively identifies the chemical fill of munitions and sealed containers. The PINS-3X variant of the system is used to identify explosives and uses a deuterium-tritium (DT) electronic neutron generator (ENG) as the neutron source. Use of the system, including possession and use of the neutron generator and shipment of the system components requires compliance with a number of regulations. This report outlines some of these requirements as well as some of the requirements in using the system outside of INL.
International Nuclear Information System (INIS)
Weinstein, R.; Gandini, A.; Parks, D.; Sawh, R.; Mayes, B.
2006-01-01
An experimental study of defects caused by ion irradiation has proven that very discontinuous multiple-in-line-damage results in much higher J c than continuous columnar pinning centers. This is contrary to conventional wisdom. We develop a first approximation to a theory relating J c to the morphology of pinning centers. Qualitative agreement with experiment is achieved. Conclusions indicate the relative importance of pinning potential, percolation, and critical temperature for various morphologies. Results suggest the leading importance of pinning, compared to texture, weak links and oxygenation in achievement of the goal of high J c especially in large grain HTS
Analisis Aliran Daya Berbasis Injeksi Arus dalam Bentuk Vektor
Directory of Open Access Journals (Sweden)
Ahmad Wira Satriawan
2017-11-01
Full Text Available Tulisan ini memaparkan hasil penelitian yang telah dilakukan untuk membandingkan metode analisis aliran daya berbasis injeksi arus dalam bentuk vektor dengan format polar dan rektangular. Penelitian ini dilakukan untuk memperoleh metode analisa aliran daya dengan perhitungan yang lebih cepat dan akurat, serta iterasi yang lebih sedikit. Metode iterasi Newton Raphson diadopsi dalam penelitian ini dan bahasa pemrograman Python serta library komputasinya digunakan. Analisis terhadap karakteristik konvergensi dari kedua format dilakukan pada IEEE 14-bus Test System. Dari penelitian ini diperoleh hasil bahwa format rektangular lebih unggul dibandingkan format polar untuk kasus yang diteliti.
Energy Technology Data Exchange (ETDEWEB)
Uwaba, Tomoyuki, E-mail: uwaba.tomoyuki@jaea.go.jp [Japan Atomic Energy Agency, 4002, Narita-cho, Oarai-machi, Ibaraki 311-1393 (Japan); Ito, Masahiro; Maeda, Koji [Japan Atomic Energy Agency, 4002, Narita-cho, Oarai-machi, Ibaraki 311-1393 (Japan)
2011-09-30
Highlights: > We evaluated diametral strain of fast reactor MOX fuel pins irradiated to 130 GWd/t. > The strain was due to cladding void swelling and irradiation creep. > The irradiation creep was caused by internal gas pressure and PCMI. > The PCMI was associated with pellet swelling by rim structure or by cesium uranate. > The latter effect tended to increase the cumulative damage fraction of the cladding. - Abstract: The C3M irradiation test, which was conducted in the experimental fast reactor, 'Joyo', demonstrated that mixed oxide (MOX) fuel pins with austenitic steel cladding could attain a peak pellet burnup of about 130 GWd/t safely. The test fuel assembly consisted of 61 fuel pins, whose design specifications were similar to those of driver fuel pins of a prototype fast breeder reactor, 'Monju'. The irradiated fuel pins exhibited diametral strain due to cladding void swelling and irradiation creep. The cladding irradiation creep strain were due to the pellet-cladding mechanical interaction (PCMI) as well as the internal gas pressure. From the fuel pin ceramographs and {sup 137}Cs gamma scanning, it was found that the PCMI was associated with the pellet swelling which was enhanced by the rim structure formation or by cesium uranate formation. The PCMI due to cesium uranate, which occurred near the top of the MOX fuel column, significantly affected cladding hoop stress and thermal creep, and the latter effect tended to increase the cumulative damage fraction (CDF) of the cladding though the CDF indicated that the cladding still had some margin to failure due to the creep damage.
ANALISIS CLUSTER K-MEANS DALAM PENGELOMPOKAN KEMAMPUAN MAHASISWA
Directory of Open Access Journals (Sweden)
B. Poerwanto
2016-12-01
Full Text Available Abstract. Cluster Analysis, K-Means Algorithm, Student Classification. This study aims to classify students based on learning outcomes for subject the basic of statistics (DDS, which is measured based on attendance, task, midterm (UTS, and final exams (UAS to further used to evaluate learning for subjects that require analysis of quantitative . This study uses k-means cluster analysis to classify the students into three groups based on learning outcomes. After grouped, there are 3 people in the low category, 27 in the medium category and over 70% in the high category.Abstrak. Analisis Cluster K-Means dalam Pengelompokan Kemampuan Mahasiswa. Pene-litian ini bertujuan untuk mengelompokkan mahasiswa berdasarkan hasil belajar mata kuliah dasar-dasar statistika (DDS yang diukur berdasarkan variabel nilai kehadiran, tugas, ujian tengah semester (UTS, dan ujian akhir semester (UAS untuk selanjutnya digunakan untuk mengevaluasi pembelajaran untuk mata kuliah yang membutuhkan kemampuan analisis kuantititatif yang baik. Penelitian ini menggunakan analisis cluster k-means dalam mengelompokkan mahasiswa ke dalam tiga kelompok berdasarkan hasil belajarnya. Seteleh dikelompokkan, terdapat 3 orang yang masuk pada kategori rendah, 27 orang pada kategori sedang dan lebih dari 70% pada kategori tinggi.Kata Kunci: Cluster Analysis, K-Means Algoritma, Klasifikasi Mahasiswa, Universitas Cokroaminoto Palopo
Directory of Open Access Journals (Sweden)
Fitriana A.R.
2015-11-01
Full Text Available Analisis diskriminan merupakan bagian dari analisis peubah ganda. Analisis diskriminan digunakan untuk memodelkan variabel tak bebas yang bersifat kualitatif dengan variabel bebas yang bersifat kuantitatif. Pada penelitian ini, analisis diskriminan lebih dari dua kelompok diterapkan pada data nilai akhir SMA/MA di Kabupaten Aceh Selatan yang bertujuan untuk mendapatkan model untuk pengklasifikasian kecamatan. Pengklasifikasian ini bertujuan untuk melihat perbedaan kualitas siswa SMA/MA yang berada di masing-masing kecamatan Kabupaten Aceh Selatan berdasarkan data nilai akhir. Variabel tak bebas yang digunakan berupa klasifikasi kecamatan berdasarkan rata-rata jumlah nilai akhir SMA/MA yang berada di masing-masing kecamatan yang dibentuk dengan K-Means Cluster. Sedangkan variabel bebas yang digunakan adalah data rata-rata nilai akhir SMA/MA untuk setiap mata pelajaran yang diujiankan pada masing-masing jurusan setiap kecamatan. Model yang didapatkan adalah dua model diskriminan untuk jurusan IPA dan IPS.
MONJU fuel pin performance analysis
International Nuclear Information System (INIS)
Kitagawa, H.; Yamanaka, T.; Hayashi, H.
1979-01-01
Monju fuel pin has almost the same properties as other LMFBR fuel pins, i.e. Phenix, PFR, CRBR, but would be irradiated under severe conditions: maximum linear heat rate of 381 watt/cm, hot spot cladding temperature of 675 deg C, peak burnup of 131,000 MWd/t, peak fluence (E greater than 0.1 MeV) of 2.3 10 23 n/cm 2 . In order to understand in-core performance of Monju fuel pin, its thermal and mechanical behaviour was predicted using the fast running performance code SIMPLE. The code takes into account pellet-cladding interaction due to thermal expansion and swelling, gap conductance, structural changes of fuel pellets, fission product gas release with burnup and temperature increase, swelling and creep of fuel pellets, corrosion of cladding due to sodium flow and chemical attack by fission products, and cumulative damage of the cladding due to thermal creep
Flux pinning characteristics of YBCO coated conductor
International Nuclear Information System (INIS)
Matsushita, T.; Watanabe, T.; Fukumoto, Y.; Yamauchi, K.; Kiuchi, M.; Otabe, E.S.; Kiss, T.; Watanabe, T.; Miyata, S.; Ibi, A.; Muroga, T.; Yamada, Y.; Shiohara, Y.
2005-01-01
Flux pinning properties of PLD-processed YBCO coated conductors deposited on IBAD substrate are investigated. The thickness of YBCO layer is changed in the range of 0.27-1.0 μm. The thickness dependence of critical current density, n-value and irreversibility field are measured in a wide range of magnetic field. The results are compared with the theoretical flux creep-flow model. It is found that these pinning properties are strongly influenced by the thickness as well as the pinning strength. Optimum condition for high field application of this superconductor is discussed
The fuel to clad heat transfer coefficient in advanced MX-type fuel pins
International Nuclear Information System (INIS)
Caligara, F.; Campana, M.; Mandler, R.; Blank, H.
1979-01-01
Advanced fuels (mixed carbides, nitrides and carbonitrides) are characterised by a high thermal conductivity compared to that of oxide fuels (5 times greater) and their behaviour under irradiation (amount of swelling, fracture behaviour, restructuring) is far more sensitive to the design parameters and to the operating temperature than that of oxide fuels. The use of advanced fuels is therefore conditioned by the possibility of mastering the above phenomena, and the full exploitation of their favorable neutron characteristics depends upon a good understanding of the mutual relationships of the various parameters, which eventually affect the mechanical stability of the pin. By far the most important parameter is the radial temperature profile which controls the swelling of the fuel and the build-up of stress fields within the pin. Since the rate of fission gas swelling of these fuels is relatively large, a sufficient amount of free space has to be provided within the pin. This space originally appears as fabrication porosity and as fuel-to-clad clearance. Due to the large initial gap width and to the high fuel thermal conductivity, the range of the fuel operating temperatures is mainly determined by the fuel-to-clad heat transfer coefficient h, whose correct determination becomes one of the central points in modelling. During the many years of modelling activity in the field of oxide fuels, several theoretical models have been developed to calculate h, and a large amount of experimental data has been produced for the empirical adjustment of the parameters involved, so that the situation may be regarded as rather satisfactory. The analysis lead to the following conclusions. A quantitative comparison of experimental h-values with existing models for h requires rather sophisticated instrumented irradiation capsules, which permit the measurement of mechanical data (concerning fuel and clad) together with heat rating and temperatures. More and better well
Clinical and histomorphometrical study on titanium dioxide-coated external fixation pins.
Koseki, Hironobu; Asahara, Tomohiko; Shida, Takayuki; Yoda, Itaru; Horiuchi, Hidehiko; Baba, Koumei; Osaki, Makoto
2013-01-01
Pin site infection is the most common and significant complication of external fixation. In this work, the efficacy of pins coated with titanium dioxide (TiO(2)) for inhibition of infection was compared with that of stainless steel control pins in an in vivo study. Pins contaminated with an identifiable Staphylococcus aureus strain were inserted into femoral bone in a rat model and exposed to ultraviolet A light for 30 minutes. On day 14, the animals were sacrificed and the bone and soft tissue around the pin were retrieved. The clinical findings and histological findings were evaluated in 60 samples. Clinical signs of infection were present in 76.7% of untreated pins, but in only 36.7% of TiO(2)-coated pins. The histological bone infection score and planimetric rate of occupation for bacterial colonies and neutrophils in the TiO(2)-coated pin group were lower than those in the control group. The bone-implant contact ratio of the TiO(2)-coated pin group was significantly higher (71.4%) than in the control pin group (58.2%). The TiO(2) was successful in decreasing infection both clinically and histomorphometrically. The photocatalytic bactericidal effect of TiO(2) is thought to be useful for inhibiting pin site infection after external fixation.
Synchronizability on complex networks via pinning control
Indian Academy of Sciences (India)
Keywords. Complex network; the pinning synchronization; synchronizability. ... The findings reveal the relationship between the decreasing speed of maximum eigenvalue sequence of the principal submatrices for coupling matrix and the synchronizability on complex networks via pinning control. We discuss the ...
PENGUKURAN KINERJA PERUSAHAAN PT. HADJI KALLA DENGAN MENGGUNAKAN ANALISIS ECONOMIC VALUE ADDED
2013-01-01
Tujuan dari penelitian ini adalah mengetahui kinerja Economic Value Added (EVA) yang dicapai oleh perusahaan PT. Hadji Kalla, sedangkan metode analisis yang digunakan dalam penelitian ini adalah analisis perkembangan Economic Value Added (EVA), Net Operating Profit After Tax (NOPAT) dan The purpose of this study was to determine the performance of the Economic Value Added (EVA), which is achieved by the company PT. Hadji Kalla...
Clint, S A; Eastwood, D M; Chasseaud, M; Calder, P R; Marsh, D R
2010-02-01
Although there is much in the literature regarding pin site infections, there is no accepted, validated method for documenting their state. We present a system for reliably labelling pin sites on any ring fixator construct and an easy-to-remember grading system to document the state of each pin site. Each site is graded in terms of erythema, pain and discharge to give a 3-point scale, named "Good", "Bad" and "Ugly" for ease of recall. This system was tested for intra- and inter-observer reproducibility. 15 patients undergoing elective limb reconstruction were recruited. A total of 218 pin sites were independently scored by 2 examiners. 82 were then re-examined later by the same examiners. 514 pin sites were felt to be "Good", 80 "Bad" and 6 "Ugly". The reproducibility of the system was found to be excellent. We feel our system gives a quick, reliable and reproducible method to monitor individual pin sites and their response to treatment. Crown Copyright 2009. Published by Elsevier Ltd. All rights reserved.
A pin-assisted retention technique for resin-bonded restorations.
Miara, P; Touati, B
1992-09-01
The value of pins for auxiliary retention has been demonstrated many times. The use of pins with resin-bonded restorations allows for improved aesthetics and less tooth reduction while increasing resistance to dislodging forces. Clinical and technical procedures for resin-bonded bridges with pin-assisted retention are presented.
Fission gas behavior in mixed-oxide fuel during transient overpower
International Nuclear Information System (INIS)
Randklev, E.H.; Treibs, H.A.; Mastel, B.; Baldwin, D.L.
1979-01-01
Fission gas behavior can be important in determining fuel pin and core performance during a reactor transient. The results are presented of examinations characterizing the changes in microstructural distribution and retention of fission gas in fuel for a series of transient overpower (50 cents/s) tested mixed-oxide fuel pins and their steady state siblings
Method and apparatus for enhancing vortex pinning by conformal crystal arrays
Janko, Boldizsar; Reichhardt, Cynthia; Reichhardt, Charles; Ray, Dipanjan
2015-07-14
Disclosed is a method and apparatus for strongly enhancing vortex pinning by conformal crystal arrays. The conformal crystal array is constructed by a conformal transformation of a hexagonal lattice, producing a non-uniform structure with a gradient where the local six-fold coordination of the pinning sites is preserved, and with an arching effect. The conformal pinning arrays produce significantly enhanced vortex pinning over a much wider range of field than that found for other vortex pinning geometries with an equivalent number of vortex pinning sites, such as random, square, and triangular.
The treatment of burnable poison pins in LWRWIMS
International Nuclear Information System (INIS)
Halsall, M.J.
1982-12-01
This report describes an investigation into the modelling approximations normally made when the LWR lattice code LWRWIMS is used for design calculations on assemblies containing burnable poison pins. Parameters investigated include energy group structure, intervals between calculations in MWd/te and spatial subdivision of the poison pins. An estimate is made of the effect of using pin-cell smearing with diffusion theory for the assembly geometry, instead of a more exact heterogeneous transport theory calculation. The influence on reactivity of the minor gadolinium isotopes 152, 154, 156, 158 and 160 in a poison pin dominated by the isotopes 155 and 157 is presented, and finally, recommendations on the use of LWRWIMS for this type of calculation are made. (author)
Energy Technology Data Exchange (ETDEWEB)
Louis, Heba Kareem; Amin, Esmat [Nuclear and Radiological Regulation Authority (NRRA), Cairo (Egypt). Safety Engineering Dept.
2016-03-15
The aim of the present paper is to assess the calculations of pin-by-pin group integrated fission rates within MOX/UO{sub 2} Fuel assemblies using the Monte Carlo code MCNP2.7c with two sets of the available latest nuclear data libraries used for calculating MOX-fueled systems. The data that are used in this paper are based on the benchmark by the NEA Nuclear Science Committee (NSC). The k{sub ∞} and absorption/fission reaction rates per isotope, k{sub eff} and pin-by-pin group integrated fission rates on 1/8 fraction of the geometry are determined. To assess the overall pin-by-pin fission rate distribution, the collective per cent error measures were investigated. The results of AVG, MRE and RMS error measures were less than 1 % error. The present results are compared with other participants using other Monte Carlo codes and with CEA results that were taken in the benchmark as reference. The results with ENDF/B-VI.6 are close to the results received by MVP (JENDL3.2) and SCALE 4.2 (JEF2.2). The results with ENDF/BVII.1 give higher values of k{sub ∞} reflecting the changes in the newer evaluations. In almost all results presented here, the MCNP calculated results with ENDF/B VII.1 should be considered more than those obtained by using other Monte Carlo codes and nuclear data libraries. The present calculations may be consider a reference for evaluating the numerical schemes in production code systems, as well as the global performance including cross-section data reduction methods as the calculations used continuous energy and no geometrical approximations.
New Universal Tribometer as Pin or Ball-on-Disc and Reciprocating Pin-on-Plate Types
Directory of Open Access Journals (Sweden)
H. Kaleli
2016-06-01
Full Text Available The present paper contains a description of a new Universal Tribometer design which enables simulation of different contact and test types such as pin-on-disc, ball-on-disc and linear reciprocating tests. There are many models of wear Tribometer in the world market. These devices are manufactured by various companies abroad and are imported to our country. Cost of this devices start from 50.000 euros and goes to hundreds of thousands of euros. One of the most commonly used of this device is Reciprocating Pin-on-Plate Tribo Test Machine. This wear tester is produced at a low limited cost within the KAP (Scientifical Research Project Coordinator of Yıldız Technical University. The test machine can work including three types of Tribotest rigs (Reciprocating Pin-on-Plate, Pin-on-Disc and Ball-on-Disc. It is designed to operate also at high temperatures up to 500 ˚C. The new piece of equipment allows instrumented tribological testing of piston ring and cylinder liner samples at low and high temperatures and boundary lubrication conditions of any typical gasoline or Diesel engines. Some friction results were shown in boundary lubricating conditions between piston ring and cylinder liner sliding pairs describing Tribotest machine is driven by AC servo motor which is more accurate than DC motor.
Primary hip spica with crossed retrograde intramedullary rush pins ...
African Journals Online (AJOL)
Bursitis and penetration of pins at the site of Rush pin insertion is a complication associated with this method of treatment. Conclusion: Closed reduction and internal fixation with crossed Rush pins was a superior treatment method in terms of early weight bearing and restoration of normal anatomy. Keywords: Femoral ...
Complications after pinning of supracondylar distal humerus fractures.
Bashyal, Ravi K; Chu, Jennifer Y; Schoenecker, Perry L; Dobbs, Matthew B; Luhmann, Scott J; Gordon, J Eric
2009-01-01
Supracondylar distal humerus fractures are one of the most common skeletal injuries in children. The current treatment of choice in North America is closed reduction and percutaneous pin fixation. Often surgeons leave the pins exposed beneath a cast but outside the skin. Great variation exists with respect to preoperative skin preparation, and perioperative antibiotic administration. Few data exist regarding the rate of infection and other complications. The purpose of this study is to review a large series of children to evaluate the rate of infection and other complications. A retrospective review was carried out of all patients treated at our institution over an 11-year period. A total of 622 patients were identified that were followed for a minimum of 2 weeks after pin removal. Seventeen patients had flexion-type fractures, 294 had type II fractures, and 311 had type III fractures. Seventy-four fractures (11.9%) had preoperative nerve deficits with anterior interosseous palsies being the most common (33 fractures, 5.3%). Preoperative antibiotics were given to 163 patients (26.2%). Spray and towel draping were used in 362 patients, paint and towel draping were used in 65 patients, alcohol paint and towel draping were used in 146 patients, and a full preparation and draping were used in 13 patients. The pins were left exposed under the cast in 591 fractures (95%), and buried beneath the skin in 31 fractures (5.0%). A medial pin was placed in 311 fractures with a small incision made to aid placement in 18 of these cases. The most common complication was pin migration necessitating unexpected return to the operating room for pin removal in 11 patients (1.8%). One patient developed a deep infection with septic arthritis and osteomyelitis (0.2%). Five additional patients had superficial skin infections and were treated with oral antibiotics for a total infection rate of 6 of 622 patients (1.0%). One patient ultimately had a malunion and 4 others returned to the
A three-dimensional pin-wise analysis for CEA ejection accident
Energy Technology Data Exchange (ETDEWEB)
Park, Guen-Tae; Park, Min-Ho; Park, Jin-Woo; Um, Kil-Sup; Choi, Tong-Soo [KEPCO NF, Daejeon (Korea, Republic of)
2016-10-15
The ejection of a control element assembly (CEA) with high reactivity worth causes the sudden insertion of reactivity into the core. Immediately after the CEA ejection, the nuclear power of the reactor dramatically increases in an exponential behavior until the doppler effect becomes important and turns the reactivity balance and power down to lower levels. The 3-D CEA ejection analysis methodology has been developed using the multi-dimensional code coupling system, CHASER, which couples three dimensional core neutron kinetics code ASTRA, subchannel analysis code THALES, and fuel performance analysis code FROST using message passing interface (MPI). This paper presents the pin-by-pin level analysis result with the 3-D CEA ejection analysis methodology using the CHASER. The pin-by-pin level analysis consists of DNBR, enthalpy and Pellet/Clad Mechanical Interaction (PCMI) analysis. All the evaluations are simulated for APR1400 plant loaded with PLUS7 fuel. In this paper, the pin-by-pin analysis using the multidimensional core transient code, CHASER, is presented with respect to enthalpy, DNBR and PCMI for APR1400 plant loaded with PLUS7 fuel. For the pin-by-pin enthalpy and DNBR analysis, the quarter core for HFP case or 15 - 20 assemblies around the most severe assembly for part powers or HZP cases are selected. And PCMI calculation is performed for all the rods in the whole core during a conservative time period. The pin-by-pin analysis results show that the regulatory guidelines of CEA ejection accident are satisfied.
Post irradiation examination on test fuel pins for PWR
International Nuclear Information System (INIS)
Fogaca Filho, N.; Ambrozio Filho, F.
1981-01-01
Certain aspects of irradiation technology on test fuel pins for PWR, are studied. The results of post irradiation tests, performed on test fuel pins in hot cells, are presented. The results of the tests permit an evaluation of the effects of irradiation on the fuel and cladding of the pin. (Author) [pt
Statistics of dislocation pinning at localized obstacles
Energy Technology Data Exchange (ETDEWEB)
Dutta, A. [S. N. Bose National Centre for Basic Sciences, Salt Lake, Kolkata 700098 (India); Bhattacharya, M., E-mail: mishreyee@vecc.gov.in; Barat, P. [Variable Energy Cyclotron Centre, 1/AF Bidhannagar, Kolkata 700064 (India)
2014-10-14
Pinning of dislocations at nanosized obstacles like precipitates, voids, and bubbles is a crucial mechanism in the context of phenomena like hardening and creep. The interaction between such an obstacle and a dislocation is often studied at fundamental level by means of analytical tools, atomistic simulations, and finite element methods. Nevertheless, the information extracted from such studies cannot be utilized to its maximum extent on account of insufficient information about the underlying statistics of this process comprising a large number of dislocations and obstacles in a system. Here, we propose a new statistical approach, where the statistics of pinning of dislocations by idealized spherical obstacles is explored by taking into account the generalized size-distribution of the obstacles along with the dislocation density within a three-dimensional framework. Starting with a minimal set of material parameters, the framework employs the method of geometrical statistics with a few simple assumptions compatible with the real physical scenario. The application of this approach, in combination with the knowledge of fundamental dislocation-obstacle interactions, has successfully been demonstrated for dislocation pinning at nanovoids in neutron irradiated type 316-stainless steel in regard to the non-conservative motion of dislocations. An interesting phenomenon of transition from rare pinning to multiple pinning regimes with increasing irradiation temperature is revealed.
ANALISIS HARGA POKOK PRODUKSI DAN PENERAPAN TARGET COSTING PADA UD WAJUKU MAKASSAR
-, CHAIDIR HAFID
2017-01-01
ABSTRAK Analisis Harga Pokok Produksi dan Penerapan Target Costing pada UD Wajuku Makassar The Analysis of The Cost of Goods Manufactured and Implementation of Target Costing in UD Wajuku Makassar Chaidir Hafid Asri Usman Syahrir Penelitian ini bertujuan untuk mengetahui perhitungan harga pokok produksi baju kaos polos sebelum dan setelah penerapan metode target costing pada UD Wajuku Makassar. Metode pengumpulan data yang digunakan adalah dokumentasi. Metode analisis dat...
Artificial pinning center technology to enhance vortex pinning in YBCO coated conductors
International Nuclear Information System (INIS)
Matsumoto, Kaname; Mele, Paolo
2010-01-01
Crystalline defects on the nano-scale, which are called artificial pinning centers (APCs), were successfully introduced into high-temperature superconductors (HTS) by nanotechnology, in order to strongly pin the quantized vortices. The critical current densities, J c , of the HTS films were dramatically improved by APCs. It is possible to form APCs in high-quality epitaxial films, keeping the desired dimensionality, volume fraction, spatial distribution and so on. The in-field J c of HTS films at 77 K was improved by one order of magnitude compared with previous values using APCs. This technology can be applied to the coated conductor technology in progress, and a high J c has already been reported. A current outline of the research is described in this review.
International Nuclear Information System (INIS)
Kobayashi, H.; Yamada, Y.; Ishida, S.; Takahashi, K.; Konishi, M.; Ibi, A.; Miyata, S.; Kato, T.; Hirayama, T.; Shiohara, Y.
2006-01-01
In order to fabricate YBa2Cu3O7-x (YBCO) coated conductors with high critical current density Jc in magnetic fields, we fabricated YBCO coated conductors with artificial pinning centers by the pulsed laser deposition (PLD) method on a self epitaxial PLD-CeO2 layer and ion-beam assisted deposition (IBAD)-Gd2Zr2O7 (GZO) buffered Hastelloy tape. Artificial pinning centers were introduced by the PLD deposition using the yttria-stabilized zirconia (YSZ) oxide target (nano-dot method) and YBCO target including YSZ particles (mixed target method). In the experiments using YSZ oxide target, YSZ nano-dots were observed. They were approximately 15 nm in height and 10 nm to 70 nm in diameter. We found that the density of nano-dots was controlled by the number of laser pulses. These samples exhibited higher Jc than YBCO films in magnetic fields. Furthermore, a similar improvement of Jc was observed in the experiments using YBCO target including YSZ particles. TEM observation revealed that columnar nano-structure made of BaZrO3 was formed during YBCO deposition and it was effective for pinning. We call this new epitaxial nano-structure 'bamboo structure' from its anisotropic growth and morphology
On the obstructions to non-Cliffordian pin structures
Energy Technology Data Exchange (ETDEWEB)
Chamblin, A. (Dept. of Applied Maths and Theoretical Physics, Univ. of Cambridge (United Kingdom))
1994-07-01
We derive the topological obstructions to the existence of non-Cliffordian pin structures on four-dimensional spacetimes. We apply these obstructions to the study of non-Cliffordian pin-Lorentz cobordism. We note that our method of derivation applies equally well in any dimension and in any signature, and we present a general format for calculating obstructions in these situations. Finally, we interpret the breakdown of pin structure and discuss the relevance of this to aspects of physics. (orig.)
International Nuclear Information System (INIS)
Baek, Seung-heon Chris; Seo, Yu-Jin; Oh, Joong Gun; Albert Park, Min Gyu; Bong, Jae Hoon; Yoon, Seong Jun; Lee, Seok-Hee; Seo, Minsu; Park, Seung-young; Park, Byong-Guk
2014-01-01
In this paper, we report the alleviation of the Fermi-level pinning on metal/n-germanium (Ge) contact by the insertion of multiple layers of single-layer graphene (SLG) at the metal/n-Ge interface. A decrease in the Schottky barrier height with an increase in the number of inserted SLG layers was observed, which supports the contention that Fermi-level pinning at metal/n-Ge contact originates from the metal-induced gap states at the metal/n-Ge interface. The modulation of Schottky barrier height by varying the number of inserted SLG layers (m) can bring about the use of Ge as the next-generation complementary metal-oxide-semiconductor material. Furthermore, the inserted SLG layers can be used as the tunnel barrier for spin injection into Ge substrate for spin-based transistors.
Analisis Komoditi Unggulan Subsektor Tanaman Pangan di Sumatera Utara Tahun 2010 – 2014
Sinaga, Terry Praganda
2016-01-01
Tujuan penelitian ini adalah untuk mengetahui perkembangan produksi komoditi tanaman pangan selama periode tersebut sehingga dapat menganalisis komoditi subsektor tanaman pangan yang menjadi unggulan di Sumatera Utara. Komoditi unggulan tersebut juga dijabarkan untuk setiap kabupatem/kota yang ada di Sumatera Utara. Metode yang digunakan yaitu secara Convenience Sampling, dan metode analisis data dengan menggunakan analisis Location Quotient. Hasil penelitian menyimpulkan ba...
Experimental Qualification of the Sleeved Pin Multilink Attachment for Divertor PFC's
International Nuclear Information System (INIS)
Poutanen, J.; McCallum, A.; Turner, A.; Merola, M.
2006-01-01
The latest design for connecting the limited life ITER divertor plasma facing components (PFC's) to the reusable cassette body is the so called sleeved pin multilink attachment. The connection is made by expanding a 43 mm diameter hollow AlBr pin inside the fixation holes of components of the cassette body and PFC by a swaging process. The multilink is an easy, safe and fast assembly method, but the original dismantling method of drilling out the pin was found troublesome. Therefore, in the latest attachment design a thin sleeve is incorporated between the pin and the holes, which makes it possible to dismantle the joint by simply pulling out the pin and sleeve sequentially. Experimental qualification of the new sleeved design is now proceeding. The aim of the experimental qualification is to prove that the sleeved design meets the requirements of load carrying capability, clearance free connection, and easy and safe removal. Associated analytical studies were performed to develop and verify theoretical models and correlations for use in design. Results from the experimental qualification will provide reference information for developing tools for making and removing the connection. Theoretical finite element models in association with the results of earlier test campaigns with nonsleeved design were used to determine pin expansion parameters. The expansion parameters were verified with plate-pin tests measuring contact pressures produced by pin expansion. The plate-pin tests were also used to demonstrate the feasibility of pin removal and develop pin removal methodology. The mechanical capabilities of the connection design are being examined with test series of cyclic tensile loading plus articulation-induced loading of a single connection mock-up. Remaking properties of the attachment are being studied with multiple swaging and removing of the pin into the fixation holes. Finally the dismantling of the connection will be examined with full length pin extraction
Dynamic Phases of Vortices in Superconductors with Periodic Pinning
International Nuclear Information System (INIS)
Reichhardt, C.; Olson, C.; Nori, F.
1997-01-01
We present results from extensive simulations of driven vortex lattices interacting with periodic arrays of pinning sites. Changing an applied driving force produces a rich variety of novel dynamical plastic flow phases which are very distinct from those observed in systems with random pinning arrays. Signatures of the transition between these different dynamical phases include sudden jumps in the current-voltage curves as well as marked changes in the vortex trajectories and vortex lattice order. Several dynamical phase diagrams are obtained as a function of commensurability, pinning strength, and spatial order of the pinning sites. copyright 1997 The American Physical Society
ITP Hanford Type 40 pin electrical connector failure analysis
International Nuclear Information System (INIS)
Imrich, K.J.
1993-01-01
Corrosion products observed on the ITP Hanford Type 40 pin electrical connectors would be expected to adversely affect the power and control signals supplied to process equipment in the filter cell by the connectors. Corrosion products were consistent with those found on similar pins in DWPF. The recommendations based on the findings in this investigation are as follows: (1) Replace male and female rhodium plated pins with gold plated pins. (2) Replace the galvanized carbon steel spring on the male connector with a stainless steel spring. (3) Install protective caps over Hanford connectors when jumpers are removed
Discovery of novel selenium derivatives as Pin1 inhibitors by high-throughput screening
International Nuclear Information System (INIS)
Subedi, Amit; Shimizu, Takeshi; Ryo, Akihide; Sanada, Emiko; Watanabe, Nobumoto; Osada, Hiroyuki
2016-01-01
Peptidyl prolyl cis/trans isomerization by Pin1 regulates various oncogenic signals during cancer progression, and its inhibition through multiple approaches has established Pin1 as a therapeutic target. However, lack of simplified screening systems has limited the discovery of potent Pin1 inhibitors. We utilized phosphorylation-dependent binding of Pin1 to its specific substrate to develop a screening system for Pin1 inhibitors. Using this system, we screened a chemical library, and identified a novel selenium derivative as Pin1 inhibitor. Based on structure-activity guided chemical synthesis, we developed more potent Pin1 inhibitors that inhibited cancer cell proliferation. -- Highlights: •Novel screening for Pin1 inhibitors based on Pin1 binding is developed. •A novel selenium compound is discovered as Pin1 inhibitor. •Activity guided chemical synthesis of selenium derivatives resulted potent Pin1 inhibitors.
Resistance projection welding small pins in vacuum tube feedthrough assembly
International Nuclear Information System (INIS)
Kuncz, F. Jr.
1980-01-01
Resistance projection welding of two stainless steel pins to a cup is successfully accomplished by specially designed electrodes and by forming domes on the pin ends. Details of electrode and pin construction are given, as well as welding parameters
PROCOPE, Collision Probability in Pin Clusters and Infinite Rod Lattices
International Nuclear Information System (INIS)
Amyot, L.; Daolio, C.; Benoist, P.
1984-01-01
1 - Nature of physical problem solved: Calculation of directional collision probabilities in pin clusters and infinite rod lattices. 2 - Method of solution: a) Gauss integration of analytical expressions for collision probabilities. b) alternately, an approximate closed expression (not involving integrals) may be used for pin-to-pin interactions. 3 - Restrictions on the complexity of the problem: number of fuel pins must be smaller than 62; maximum number of groups of symmetry is 300
Liquid-metal pin-fin pressure drop by correlation in cross flow
International Nuclear Information System (INIS)
Wang, Zhibi; Kuzay, T.M.; Assoufid, L.
1994-01-01
The pin-fin configuration is widely used as a heat transfer enhancement method in high-heat-flux applications. Recently, the pin-fin design with liquid-metal coolant was also applied to synchrotron-radiation beamline devices. This paper investigates the pressure drop in a pin-post design beamline mirror with liquid gallium as the coolant. Because the pin-post configuration is a relatively new concept, information in literature about pin-post mirrors or crystals is rare, and information about the pressure drop in pin-post mirrors with liquid metal as the coolant is even more sparse. Due to this the authors considered the cross flow in cylinder-array geometry, which is very similar to that of the pin-post, to examine the pressure drop correlation with liquid metals over pin fins. The cross flow of fluid with various fluid characteristics or properties through a tube bank was studied so that the results can be scaled to the pin-fin geometry with liquid metal as the coolant. Study lead to two major variables to influence the pressure drop: fluid properties, viscosity and density, and the relative length of the posts. Correlation of the pressure drop between long and short posts and the prediction of the pressure drop of liquid metal in the pin-post mirror and comparison with an existing experiment are addressed
Loss of Pin1 Suppresses Hedgehog-Driven Medulloblastoma Tumorigenesis
Directory of Open Access Journals (Sweden)
Tao Xu
2017-03-01
Full Text Available Medulloblastoma is the most common malignant brain tumor in children. Therapeutic approaches to medulloblastoma (combination of surgery, radiotherapy, and chemotherapy have led to significant improvements, but these are achieved at a high cost to quality of life. Alternative therapeutic approaches are needed. Genetic mutations leading to the activation of the Hedgehog pathway drive tumorigenesis in ~30% of medulloblastoma. In a yeast two-hybrid proteomic screen, we discovered a novel interaction between GLI1, a key transcription factor for the mediation of Hedgehog signals, and PIN1, a peptidylprolyl cis/trans isomerase that regulates the postphosphorylation fate of its targets. The GLI1/PIN1 interaction was validated by reciprocal pulldowns using epitope-tagged proteins in HEK293T cells as well as by co-immunoprecipiations of the endogenous proteins in a medulloblastoma cell line. Our results support a molecular model in which PIN1 promotes GLI1 protein abundance, thus contributing to the positive regulation of Hedgehog signals. Most importantly, in vivo functional analyses of Pin1 in the GFAP-tTA;TRE-SmoA1 mouse model of Hedgehog-driven medulloblastoma demonstrate that the loss of Pin1 impairs tumor development and dramatically increases survival. In summary, the discovery of the GLI1/PIN1 interaction uncovers PIN1 as a novel therapeutic target in Hedgehog-driven medulloblastoma tumorigenesis.
Improved Retrieval Technique of pin-wise composition for spent fuel recycling
Energy Technology Data Exchange (ETDEWEB)
Park, YunSeo; Kim, Myung Hyun [Kyung Hee University , Yongin (Korea, Republic of)
2016-10-15
New reutilization method which does not require fabrication processing was suggested and showed feasibility by Dr. Aung Tharn Daing. This new reutilization method is predict spent nuclear fuel pin composition, reconstruct new fuel assembly by spent nuclear pin, and directly reutilize in same PWR core. There are some limitation to predict spent nuclear fuel pin composition on his methodology such as spatial effect was not considered enough. This research suggests improving Dr. Aung Tharn Daing's retrieval technique of pin-wise composition. This new method classify fuel pin groups by its location effect in fuel assembly. Most of fuel pin composition along to burnup in fuel assembly is not highly dependent on location. However, compositions of few fuel pins where near water hole and corner of fuel assembly are quite different in same burnup. Required number of nuclide table is slightly increased from 3 to 6 for one fuel assembly with this new method. Despite of this little change, prediction of the pin-wise composition became more accurate. This new method guarantees two advantages than previous retrieving technique. First, accurate pin-wise isotope prediction is possible by considering location effect in a fuel assembly. Second, it requires much less nuclide tables than using full single assembly database. Retrieving technique of pin-wise composition can be applied on spent fuel management field useful. This technique can be used on direct use of spent fuel such as Dr. Aung Tharn Daing showed or applied on pin-wise waste management instead of conventional assembly-wise waste management.
Progress in fuel pin modelling in the USA
Energy Technology Data Exchange (ETDEWEB)
Stephen, J D; Biancheria, A; Leibnitz, D; O' Reilly, B D; Liu, Y Y; Labar, M P; Gneiting, B C [General Electric Company, Sunnyvale, CA (United States)
1979-12-01
In the USA, the focus for theoretical fuel pin modeling is the LIFE system. This system of codes, algorithms, criteria and analysis guidelines is intended to provide a common basis for communication amongst the development groups, a reference set of analysis guidelines for design, and eventually a consensus on the state-of-the-art for licensing. The technical objective is to predict the effect of design options on fuel pin performance limits, which include fuel temperature, pin deformation and cladding breach during normal operation and design basis transients. The mechanistic approach to modeling is taken in LIFE to the extent possible. That is, the approach is to describe the key phenomena in sufficient detail to provide a fundamental understanding of their synergistic effect on the fuel pin performance limits.
PIN architecture for ultrasensitive organic thin film photoconductors.
Jin, Zhiwen; Wang, Jizheng
2014-06-17
Organic thin film photoconductors (OTFPs) are expected to have wide applications in the field of optical communications, artificial vision and biomedical sensing due to their great advantages of high flexibility and low-cost large-area fabrication. However, their performances are not satisfactory at present: the value of responsivity (R), the parameter that measures the sensitivity of a photoconductor to light, is below 1 AW(-1). We believe such poor performance is resulted from an intrinsic self-limited effect of present bare blend based device structure. Here we designed a PIN architecture for OTFPs, the PIN device exhibits a significantly improved high R value of 96.5 AW(-1). The PIN architecture and the performance the PIN device shows here should represent an important step in the development of OTFPs.
Investigation of pinning in MgB2 superconductors
International Nuclear Information System (INIS)
Mohammad, S.; Reissner, M.; Steiner, W.; Bauer, E.; Giovannini, M.
2006-01-01
Full text: The pinning behaviour of bulk MgB 2 superconductors is peculiar in many respects. Pinning seems to be stronger than in classical high T C materials and there seems to be no weak link problem in these compounds, giving hope to produce bulk samples and wires with current densities appropriate for technical applications. But, although many studies concerning the pinning behaviour in this compound appeared in recent years, the results are still contradictory. In the present work we present results of an investigation of the pinning behaviour by magnetic relaxation measurements of three MgB 2 samples: a pure one, a sample with 8 at% Al substitution and a sample with 10 wt% of SiC admixture. A comparison of different analyses methods is given. (author)
Material Flow and Oxide Particle Distributions in Friction-Stir Welded F/M-ODS Sheets
Energy Technology Data Exchange (ETDEWEB)
Kang, Suk Hoon; Noh, Sanghoon; Jin, Hyun Ju; Kim, Tae Kyu [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)
2015-05-15
It is well known that uniform nano-oxide dispersoids act as pinning points to obstruct dislocation and grain boundary motion in ODS(Oxide dispersion strengthened) steel. However, these advantages will disappear while the material is subjected to the high temperature of conventional fusion welding. There is only limited literature available on the joining of ODS steels. Friction stir welding (FSW) is considered to be the best welding technique for welding ODS steels as the technique helps in retaining the homogeneous nano-oxide particles distributions in matrix. FSW is a solid.state, hot.shear joining process in which a rotating tool with a shoulder and terminating in a threaded pin, moves along the butting surfaces of two rigidly clamped plates placed on a backing plate. Heat generated by friction at the shoulder and to a lesser extent at the pin surface, softens the material being welded. Severe plastic deformation and flow of this plasticised metal occurs as the tool is translated along the welding direction. Material is transported from the front of the tool to the trailing edge where it is forged into a joint. Friction stir welding appears to be a very promising technique for the welding of FMS and ODS steels. This study found that, during FSW, the forward movement of the tool pin results in loose contact between the tool pin and the receding material on the advancing side.
Passive measurements of mixed-oxide fuel for nuclear nonproliferation
International Nuclear Information System (INIS)
Dolan, Jennifer L.; Flaska, Marek; Pozzi, Sara A.; Chichester, David L.
2013-01-01
We present new results on passive measurements and simulations of mixed-oxide fuel-pin assemblies. Potential tools for mixed-oxide fuel pin characterization are discussed for future nuclear-nonproliferation applications. Four EJ-309 liquid scintillation detectors coupled with an accurate pulse timing and digital, offline and optimized pulse-shape discrimination method were used. Measurement analysis included pulse-height distributions to distinguish between purely fission neutron sources and alpha-n plus fission neutrons sources. Time-dependent cross-correlation functions were analyzed to measure the fission neutron contribution to the measured sample's neutron source. The use of Monte Carlo particle transport code MCNPX-PoliMi is discussed in conjunction with the measurements
Wear-Induced Changes in FSW Tool Pin Profile: Effect of Process Parameters
Sahlot, Pankaj; Jha, Kaushal; Dey, G. K.; Arora, Amit
2018-06-01
Friction stir welding (FSW) of high melting point metallic (HMPM) materials has limited application due to tool wear and relatively short tool life. Tool wear changes the profile of the tool pin and adversely affects weld properties. A quantitative understanding of tool wear and tool pin profile is crucial to develop the process for joining of HMPM materials. Here we present a quantitative wear study of H13 steel tool pin profile for FSW of CuCrZr alloy. The tool pin profile is analyzed at multiple traverse distances for welding with various tool rotational and traverse speeds. The results indicate that measured wear depth is small near the pin root and significantly increases towards the tip. Near the pin tip, wear depth increases with increase in tool rotational speed. However, change in wear depth near the pin root is minimal. Wear depth also increases with decrease in tool traverse speeds. Tool pin wear from the bottom results in pin length reduction, which is greater for higher tool rotational speeds, and longer traverse distances. The pin profile changes due to wear and result in root defect for long traverse distance. This quantitative understanding of tool wear would be helpful to estimate tool wear, optimize process parameters, and tool pin shape during FSW of HMPM materials.
Trending on Pinterest: an examination of pins about skin tanning.
Banerjee, Smita C; Rodríguez, Vivian M; Greene, Kathryn; Hay, Jennifer L
2018-04-10
Rates of melanoma and nonmelanoma skin cancers are on the rise in the USA with data revealing disproportionate increase in female young adults. The popularity of intentional skin tanning among U.S. adolescents is attributed to several factors, including prioritization of physical appearance, media images of tanned celebrities, ease of availability of artificial tanning facilities, and more recently, the prevalence and celebration of tanned skin on social media. Pinterest, as the third most popular social media platform, was searched for "pins" about skin tanning. The resultant "pins" were examined to understand the extent and characteristics of skin tanning portrayed on Pinterest. We analyzed pins on Pinterest about skin tanning (n = 501) through a quantitative content analysis. Overall, results indicated an overwhelmingly protanning characteristic of pins about skin tanning on Pinterest, with over 85% of pins promoting tanning behavior. The pins were generally characterized by the portrayal of a female subject (61%) and provided positive reinforcement for tanning (49%). Use of tanning for enhancing appearance was the main positive outcome expectancy portrayed in the pins (35%), and nudity or exposure of skin on arms (32%) and legs (31%) was evident in about a third of pins. With overwhelmingly positive pins promoting tanning, use of female subjects, exhibiting nudity, and appearance enhancement, there seems be to a consistent targeting of female users to accept tanning as a socially acceptable and popular behavior. The findings indicate a need for developing sun protection messages and the leveraging of social media for dissemination of skin cancer prevention and detection messages.
Effective augmentation of networked systems and enhancing pinning controllability
Jalili, Mahdi
2018-06-01
Controlling dynamics of networked systems to a reference state, known as pinning control, has many applications in science and engineering. In this paper, we introduce a method for effective augmentation of networked systems, while also providing high levels of pinning controllability for the final augmented network. The problem is how to connect a sub-network to an already existing network such that the pinning controllability is maximised. We consider the eigenratio of the augmented Laplacian matrix as a pinning controllability metric, and use graph perturbation theory to approximate the influence of edge addition on the eigenratio. The proposed metric can be effectively used to find the inter-network links connecting the disjoint networks. Also, an efficient link rewiring approach is proposed to further optimise the pinning controllability of the augmented network. We provide numerical simulations on synthetic networks and show that the proposed method is more effective than heuristic ones.
Reconstruction calculation of pin power for ship reactor core
International Nuclear Information System (INIS)
Li Haofeng; Shang Xueli; Chen Wenzhen; Wang Qiao
2010-01-01
Aiming at the limitation of the software that pin power distribution for ship reactor core was unavailable, the calculation model and method of the axial and radial pin power distribution were proposed. Reconstruction calculations of pin power along axis and radius was carried out by bicubic and bilinear interpolation and cubic spline interpolation, respectively. The results were compared with those obtained by professional reactor physical soft with fine mesh difference. It is shown that our reconstruction calculation of pin power is simple and reliable as well as accurate, which provides an important theoretic base for the safety analysis and operating administration of the ship nuclear reactor. (authors)
Clinical and histomorphometrical study on titanium dioxide-coated external fixation pins
Directory of Open Access Journals (Sweden)
Koseki H
2013-02-01
Full Text Available Hironobu Koseki,1 Tomohiko Asahara,1 Takayuki Shida,1 Itaru Yoda,1 Hidehiko Horiuchi,1 Koumei Baba,2 Makoto Osaki11Department of Orthopedic Surgery, Graduate School of Medicine, Nagasaki University, 2Industrial Technology Center of Nagasaki, Nagasaki, JapanBackground: Pin site infection is the most common and significant complication of external fixation. In this work, the efficacy of pins coated with titanium dioxide (TiO2 for inhibition of infection was compared with that of stainless steel control pins in an in vivo study.Methods: Pins contaminated with an identifiable Staphylococcus aureus strain were inserted into femoral bone in a rat model and exposed to ultraviolet A light for 30 minutes. On day 14, the animals were sacrificed and the bone and soft tissue around the pin were retrieved. The clinical findings and histological findings were evaluated in 60 samples.Results: Clinical signs of infection were present in 76.7% of untreated pins, but in only 36.7% of TiO2-coated pins. The histological bone infection score and planimetric rate of occupation for bacterial colonies and neutrophils in the TiO2-coated pin group were lower than those in the control group. The bone-implant contact ratio of the TiO2-coated pin group was significantly higher (71.4% than in the control pin group (58.2%. The TiO2 was successful in decreasing infection both clinically and histomorphometrically.Conclusion: The photocatalytic bactericidal effect of TiO2 is thought to be useful for inhibiting pin site infection after external fixation.Keywords: titanium dioxide, external fixation, bactericidal activity, Staphylococcus aureus
Vortex Avalanches with Periodic Arrays of Pinning Sites
Abbas, J.; Heckel, T.; Kakalios, J.
2001-03-01
Numerical simulations by Nori and co-workers of dynamical phase transitions for magnetic vortices in type II superconductors when the defects which act as pinning sites are arranged in a periodic array have found a dramatic non-linear relationship between vortex voltage and driving current.2,4 In order to experimentally test the predictions of these simulations, a macroscopic physical analog of an array of flux vortices in the presense of an ordered lattice of pinning sites has been constructed. This simple table-top experimental system consists of conventional household magnets, arranged in an ordered grid (serving as the lattice of fixed pinning centers). A plexiglass sheet is positioned above these fixed magnets, and another collection of magnets (representing the magnetic flux vortices), oriented so that they are attracted to the fixed magnets are placed on top of the sheet. The entire apparatus is then tilted to a given angle (the analog of the driving voltage) and the velocity of the avalanching magnets is recorded using the induced voltage in a pick-up coil. By varying the ratio of movable magnets to fixed pinning magnets, the filling fraction can be adjusted, as can the pinning strength, by adjusting the separation of the plexiglass sheet between the fixed and movable magnets. The velocity of the avalanching magnets as the filling fraction is varied displays a jamming transition, with a non-trivial dependence on the pinning strength of the lattice of fixed magnets below the sheet.
APLIKASI METODE-METODE AGGLOMERATIVE DALAM ANALISIS KLASTER PADA DATA TINGKAT POLUSI UDARA
Directory of Open Access Journals (Sweden)
Dewi Rachmatin
2014-09-01
Full Text Available ABSTRAK Analisis Klaster merupakan analisis pengelompokkan data yang mengelompokkan data berdasarkan informasi yang ditemukan pada data. Tujuan dari analisis klaster adalah agar objek-objek di dalam satu kelompok memiliki kesamaan satu sama lain sedangkan dengan objek-objek yang berbeda kelompok memiliki perbedaan. Analisis klaster dibagi menjadi dua metode yaitu metode hirarki dan metode non-hirarki. Metode hirarki dibagi menjadi dua, yaitu metode agglomerative (pemusatan dan metode divisive (penyebaran. Metode-metode yang termasuk dalam metode agglomerative adalah Single Linkage Method, Complete Linkage Method, Average Linkage Method, Ward’s Method, Centroid Method dan Median Method. Pada artikel ini dibahas metode-metode agglomerative tersebut yang diterapkan pada data tingkat polusi udara. Masing-masing metode tersebut memberikan jumlah klaster yang berbeda. Kata Kunci : Analisis Klaster, Single Linkage Method, Complete Linkage Method, Average Linkage Method, Ward’s Method, Centroid Method dan Median Method. ABSTRACT Cluster analysis is an analysis of the data classification based on information found in the data.The objective of cluster analysis is that the objects in the group have in common with each other, while the different objects have different groups. Cluster analysis is divided into two methods : the method of non-hierarchical and hierarchical methods.Hierarchical method is divided into two methods, namely agglomerative methods (concentration and divisive methods (deployment. The methods included in the agglomerative method is Single Linkage Method, Complete Linkage Method, Average Linkage Method, Ward 's Method, Method and Median Centroid Method. In this article discussed the agglomerative methods were applied to the data rate of air pollution. Each of these methods provides a different number of clusters. Keywords: Cluster Analysis , Single Linkage Method, Complete Linkage Method, Average Linkage Method, Ward
Optimal pin enrichment distributions in nuclear reactor fuel bundles
International Nuclear Information System (INIS)
Lim, E.Y.
1976-01-01
A methodology has been developed to determine the fuel pin enrichment distribution that yields the best approximation to a prescribed power distribution in nuclear reactor fuel bundles. The problem is formulated as an optimization problem in which the optimal pin enrichments minimize the sum of squared deviations between the actual and prescribed fuel pin powers. A constant average enrichment constraint is imposed to ensure that a suitable value of reactivity is present in the bundle. When constraints are added that limit the fuel pins to a few enrichment types, one must determine not only the optimal values of the enrichment types but also the optimal distribution of the enrichment types amongst the pins. A matrix of boolean variables is used to describe the assignment of enrichment types to the pins. This nonlinear mixed integer programming problem may be rigorously solved with either exhaustive enumeration or branch and bound methods using a modification of the algorithm from the continuous problem as a suboptimization. Unfortunately these methods are extremely cumbersome and computationally overwhelming. Solutions which require only a moderate computational effort are obtained by assuming that the fuel pin enrichments in this problem are ordered as in the solution to the continuous problem. Under this assumption search schemes using either exhaustive enumeration or branch and bound become computationally attractive. An adaptation of the Hooke--Jeeves pattern search technique is shown to be especially efficient
How Helpful is Colour-Cueing of PIN Entry?
Renaud, Karen; Ramsay, Judith
2014-01-01
21st Century citizens are faced with the need to remember numbers of PINs (Personal Identification Numbers) in order to do their daily business, and they often have difficulties due to human memory limitations. One way of helping them could be by providing cues during the PIN entry process. The provision of cues that would only be helpful to the PIN owner is challenging because the cue should only make sense to the legitimate user, and not to a random observer. In this paper we report on an e...
Risk analysis; Analisis de riesgos
Energy Technology Data Exchange (ETDEWEB)
Baron, J H; Nunez McLeod, J; Rivera, S S [Universidad Nacional de Cuyo, Mendoza (Argentina). Instituto de Capacitacion Especial y Desarrollo de Ingenieria Asistida por Computadora (CEDIAC)
1997-07-01
This book contains a selection of research works performed in the CEDIAC Institute (Cuyo National University) in the area of Risk Analysis, with specific orientations to the subjects of uncertainty and sensitivity studies, software reliability, severe accident modeling, etc. This volume presents important material for all those researches who want to have an insight in the risk analysis field, as a tool to solution several problems frequently found in the engineering and applied sciences field, as well as for the academic teachers who want to keep up to date, including the new developments and improvements continuously arising in this field. [Spanish] Este libro contiene una seleccion de trabajos de investigacion realizados dentro del Instituto de Capacitacion Especial y Desarrollo de la Ingenieria Asistida por Computadora en el area del analisis de riesgos, con una orientacion hacia el estudio de incertidumbres y sensibilidad, confiabilidad de software, modelacion de accidentes severos, etc. Este volumen recoge un material de indudable importancia e interes para todos aquellos investigadores y profesionales que desean incursionar en este campo del analisis de riesgos como herramienta para la solucion de problemas frecuentemente encontrados en la ingenieria y las ciencias aplicadas, asi como para los academicos que desean mantenerse al dia, conociendo los nuevos desarrollos y tecnicas que constantemente aparecen en su area.
Sodium erosion of boron carbide from breached absorber pins
International Nuclear Information System (INIS)
Basmajian, J.A.; Baker, D.E.
1981-03-01
The purpose of the irradiation experiment was to provide an engineering demonstration of the irradiation behavior of breached boron carbide absorber pins. By building defects into the cladding of prototypic absorber pins, and performing the irradiation under typical FFTF operating conditions, a qualitative assessment of the consequences of a breach was achieved. Additionally, a direct comparison of pin behavior with that of the ex-reactor test could be made
Theory of activated glassy dynamics in randomly pinned fluids
Phan, Anh D.; Schweizer, Kenneth S.
2018-02-01
We generalize the force-level, microscopic, Nonlinear Langevin Equation (NLE) theory and its elastically collective generalization [elastically collective nonlinear Langevin equation (ECNLE) theory] of activated dynamics in bulk spherical particle liquids to address the influence of random particle pinning on structural relaxation. The simplest neutral confinement model is analyzed for hard spheres where there is no change of the equilibrium pair structure upon particle pinning. As the pinned fraction grows, cage scale dynamical constraints are intensified in a manner that increases with density. This results in the mobile particles becoming more transiently localized, with increases of the jump distance, cage scale barrier, and NLE theory mean hopping time; subtle changes of the dynamic shear modulus are predicted. The results are contrasted with recent simulations. Similarities in relaxation behavior are identified in the dynamic precursor regime, including a roughly exponential, or weakly supra-exponential, growth of the alpha time with pinning fraction and a reduction of dynamic fragility. However, the increase of the alpha time with pinning predicted by the local NLE theory is too small and severely so at very high volume fractions. The strong deviations are argued to be due to the longer range collective elasticity aspect of the problem which is expected to be modified by random pinning in a complex manner. A qualitative physical scenario is offered for how the three distinct aspects that quantify the elastic barrier may change with pinning. ECNLE theory calculations of the alpha time are then presented based on the simplest effective-medium-like treatment for how random pinning modifies the elastic barrier. The results appear to be consistent with most, but not all, trends seen in recent simulations. Key open problems are discussed with regard to both theory and simulation.
ANALISIS PENGARUH KINERJA LINGKUNGAN TERHADAP KINERJA INDUSTRI KECIL
Directory of Open Access Journals (Sweden)
Sukirman -
2012-03-01
Full Text Available Tujuan penelitian adalah mengidentifikasi, menganalisis praktik pengelolaan lingkungan pada sentra industri kecil dibandingkan best practices dalam upaya meningkatkan kinerja lingkungan di Kabupaten Pati. Kajian difokuskan pada pengelolaan lingkungan secara efektif dengan melibatkan variabel inisiatif lingkungan, keterlibatan karyawan, dan integrasi dengan supplier. Populasinya adalah seluruh perusahaan Industri Kecil di Kabupaten Pati. Sampel berjumlah 97 perusahaan. Teknik sampling menggunakan kluster sampling, dengan sampel pada sentra industri kecil di Kabupaten Pati. Analisis menggunakan analisis deskriptif dan analisis komparatif. Hasil penelitian menunjukkan praktik pengelolaan lingkungan pada sentra industri kecil di Kabupaten Pati belum dilaksanakan secara optimal. Sementara itu, variabel integrasi supplier berpengaruh langsung terhadap kinerja perusahaan.The purpose of this study is to identify and to analyze an environmental management practice which is compared to the best practices in order to improve environmental performance in the industrial centers in Pati District. This study focuses on managing the environment effectively by involving environmental initiative variables, employee involvement, and integration of suppliers. Population in this study was all small industrial enterprises in Pati regency which has 97 companies as data samples. Data were collected by using cluster sampling techniques, and samples were taken from small industrial centers in the District of Pati. Data were analyzed by using descriptive and comparative methods. Results of this study showed that environmental management practices in small industrial centers had not been implemented optimally. Meanwhile, supplier integration variables influenced directly toward corporate performance.
Position-dependency of Fuel Pin Homogenization in a Pressurized Water Reactor
Energy Technology Data Exchange (ETDEWEB)
Heo, Woong; Kim, Yonghee [Korea Advanced Institute of Science and Technolgy, Daejeon (Korea, Republic of)
2016-05-15
By considering the multi-physics effects more comprehensively, it is possible to acquire precise local parameters which can result in a more accurate core design and safety assessment. A conventional approach of the multi-physics neutronics calculation for the pressurized water reactor (PWR) is to apply nodal methods. Since the nodal methods are basically based on the use of assembly-wise homogenized parameters, additional pin power reconstruction processes are necessary to obtain local power information. In the past, pin-by-pin core calculation was impractical due to the limited computational hardware capability. With the rapid advancement of computer technology, it is now perhaps quite practical to perform the direct pin-by-pin core calculation. As such, fully heterogeneous transport solvers based on both stochastic and deterministic methods have been developed for the acquisition of exact local parameters. However, the 3-D transport reactor analysis is still challenging because of the very high computational requirement. Position-dependency of the fuel pin homogenized cross sections in a small PWR core has been quantified via comparison of infinite FA and 2-D whole core calculations with the use of high-fidelity MC simulations. It is found that the pin environmental affect is especially obvious in FAs bordering the baffle reflector regions. It is also noted that the downscattering cross section is rather sensitive to the spectrum changes of the pins. It is expected that the pinwise homogenized cross sections need to be corrected somehow for accurate pin-by-pin core calculations in the peripheral region of the reactor core.
Analisis Korelasi Kanonik Hubungan Perilaku Pemimpin dan Motivasi Kerja Karyawan
Directory of Open Access Journals (Sweden)
I Gusti Ayu Made Srinadi
2014-06-01
Full Text Available Kualitas pemimpin merupakan penentu keberhasilan organisasi yang dipimpin. Hubungan antara pemimpin dengan karyawannya merupakan hubungan saling ketergantungan yang umumnya tidak seimbang. Dalam proses interaksi yang terjadi antara pemimpin dan karyawan, berlangsung proses saling memengaruhi. Penelitian ini bertujuan untuk mencari hubungan perilaku pemimpin terhadap motivasi kerja karyawan dengan menggunakan analisis korelasi kanonik. Pengujian dengan menggunakan analisis korelasi kanonik menunjukkan bahwa perilaku pemimpin dengan motivasi karyawan memiliki keeratan hubungan dengan nilai korelasi kanonik sebesar 0,9058533. Faktor perilaku pemimpin yang paling tinggi berkorelasi dengan motivasi kerja karyawan di McDonald’s Kuta Beach adalah faktor kemampuan mengarahkan dan menghadapi karyawan dengan nilai korelasi yaitu sebesar 0,7619707.
Analisis Korelasi Kanonik Hubungan Perilaku Pemimpin dan Motivasi Kerja Karyawan
Directory of Open Access Journals (Sweden)
I Gusti Ayu Made Srinadi
2015-04-01
Full Text Available Kualitas pemimpin merupakan penentu keberhasilan organisasi yang dipimpin. Hubungan antara pemimpin dengan karyawannya merupakan hubungan saling ketergantungan yang umumnya tidak seimbang. Dalam proses interaksi yang terjadi antara pemimpin dan karyawan, berlangsung proses saling memengaruhi. Penelitian ini bertujuan untuk mencari hubungan perilaku pemimpin terhadap motivasi kerja karyawan dengan menggunakan analisis korelasi kanonik. Pengujian dengan menggunakan analisis korelasi kanonik menunjukkan bahwa perilaku pemimpin dengan motivasi karyawan memiliki keeratan hubungan dengan nilai korelasi kanonik sebesar 0,9058533. Faktor perilaku pemimpin yang paling tinggi berkorelasi dengan motivasi kerja karyawan di McDonald’s Kuta Beach adalah faktor kemampuan mengarahkan dan menghadapi karyawan dengan nilai korelasi yaitu sebesar 0,7619707.
Incidence and risk factors for pin tract infection in external fixation of ...
African Journals Online (AJOL)
Incidence and risk factors for pin tract infection in external fixation of fractures ... for pin tract infection, there were 93 pins scored grade 1, 32 pins grade 2, 15 ... The incidence increased from 20.5% in closed fractures to 75.9% in open fractures.
Energy Technology Data Exchange (ETDEWEB)
Polat, Ozgur [ORNL; Sinclair IV, John W [ORNL; Zuev, Yuri L [ORNL; Thompson, James R [ORNL; Christen, David K [ORNL; Cook, Sylvester W [ORNL; Kumar, Dhananjay [ORNL; Chen, Y [SuperPower Incorporated, Schenectady, New York; Selvamanickam, V. [SuperPower Incorporated, Schenectady, New York
2011-01-01
The dependence of the critical current density Jc on temperature, magnetic field, and film thickness has been investigated in (Gd-Y)BaCu-oxide materials of 0.7, 1.4, and 2.8 m thickness. Generally, the Jc decreases with film thickness at investigated temperatures and magnetic fields. The nature and strength of the pinning centers for vortices have been identified through angular and temperature measurements, respectively. These films do not exhibit c-axis correlated vortex pinning, but do have correlated defects oriented near the ab-planes. For all film thicknesses studied, strong pinning dominates at most temperatures. The vortex dynamics were investigated through magnetic relaxation studies in the temperature range of 5 77 K in 1 T and 3 T applied magnetic fields, H || surface-normal. The creep rate S is thickness dependent at high temperatures, implying that the pinning energy is also thickness dependent. Maley analyses of the relaxation data show an inverse power law variation for the effective pinning energy Ueff ~ (J0/J) . Finally, the electric field-current density (E-J) characteristics were determined over a wide range of dissipation by combining experimental results from transport, swept field magnetometry (VSM), and Superconducting Quantum Interference Device (SQUID) magnetometry. We develop a self-consistent model of the combined experimental results, leading to an estimation of the critical current density Jc0(T) in the absence of flux creep.
Displaced humeral lateral condyle fractures in children: should we bury the pins?
Das De, Soumen; Bae, Donald S; Waters, Peter M
2012-09-01
The purpose of this investigation was to determine if leaving Kirschner wires exposed is more cost-effective than burying them subcutaneously after open reduction and internal fixation (ORIF) of humeral lateral condyle fractures. A retrospective cohort study of all lateral condyle fractures treated over a 10-year period at a single institution was performed. Data on surgical technique, fracture healing, and complications were analyzed, as well as treatment costs. A decision analysis model was then constructed to compare the strategies of leaving the pins exposed versus buried. Finally, sensitivity analyses were performed, assessing cost-effectiveness when infection rates and costs of treating deep infections were varied. A total of 235 children with displaced fractures were treated with ORIF using Kirschner wires. Pins were left exposed in 41 cases (17.4%) and buried in 194 cases (82.6%); the age, sex, injury mechanisms, and fracture patterns were similar in both the groups. The median time to removal of implants was shorter with exposed versus buried pins (4 vs. 6 wk, Pfracture union or loss of reduction rates. The rate of superficial infection was higher with exposed pins (9.8% vs. 3.1%), but this was not statistically significant (P=0.076). There were no deep infections with exposed pins, whereas the rate of deep infection was 0.5% with buried pins (P=1.00). Buried pins were associated with additional complications, including symptomatic implants (7.2%); pins protruding through the skin (16%); internal pin migration necessitating additional surgery (1%); and skin necrosis (1%). The decision analysis revealed that leaving pins exposed resulted in an average cost savings of $3442 per patient. This strategy remained cost-effective even when infection rates with exposed pins approached 40%. Leaving the pins exposed after ORIF of lateral condyle fractures is safe and more cost-effective than burying the pins subcutaneously. Retrospective cohort study (level III).
Directory of Open Access Journals (Sweden)
Toni MT Munthe
2015-08-01
Full Text Available PT. ABC merupakan salah satu pabrik yang memproduksi botol kemasan kaca. Penelitian ini bertujuan untuk mengetahui layak atau tidaknya rencana investasi pada proyek Narrow Neck Press and Blow secara finansial di PT. ABC pada periode bulan April 2014 hingga bulan Juni 2014. Analisis kelayakan finansial proyek Narrow Neck Press and Blow, menggunakan metode analisis Net Present Value, Internal Rate of Return, Payback Period dan Sensitivity Analysis. Perbedaan antara nilai sekarang dari semua kas masuk dengan nilai sekarang dari semua kas keluar dari suatu proyek atau suatu investasi diperoleh dengan metode NPV, sedangkan untuk mencari tingkat bunga yang menyamakan nilai sekarang dari aliran kas bersih dan investasi diperoleh dengan metode IRR. Metode analisis yang dapat digunakan untuk mengetahui berapa lamakah waktu yang diperlukan untuk menutup dana yang dikeluarkan untuk suatu proyek dapat diperoleh dengan metode Payback Period. Setelah itu, dilakukan pengujian menggunakan sensitivitas analisis untuk mengetahui tingkat sensitivitas untuk tiap-tiap parameter terhadap persentase kenaikan dan penurunan. Dari hasil analisis data diperoleh nilai NPV sebesar Rp. 1.179.728.649.900,06, nilai IRR sebesar 56,36% dan periode pengembalian terletak pada 2 tahun 2 bulan 9 hari. Dengan menggunakan analisis sensitivitas dapat diketahui bahwa proyek ini sangat sensitif terhadap penurunan volume produksi. Berdasarkan hasil perhitungan, titik impas akan dicapai apabila volume produksi 213.403.267 unit per tahun atau 88,92% dari volume produksi awal. Nilai ini menunjukkan bahwa apabila volume produksi pada suatu periode mengalami penurunan lebih dari 11,08% dari volume produksi awal, maka investasi tersebut akan merugikan.
Analisis Industri Ritel Di Indonesia
Soliha, Euis
2008-01-01
This article presents an overview the analisys of retail industry in Indonesia.Retail industry in Indonesia grow rapidly. Industrial presence of modern retailbasically exploits public shopping pattern especially middle-weight and to which donot want to mill around in traditional market. Analysis Five Forces is used toanalysis retail industry. Analysis five force is bargaining power of buyers,bargaining power of suppliers, threat of new entrants, threat of new substituteproducts, and rivalry a...
International Nuclear Information System (INIS)
Uegata, T.; Saji, E.; Tanaka, H.
1993-01-01
Intranodal pin power distributions calculated by the CASMO-3/SIMULATE-3 code have been compared with pin gamma scan measurements. These data were obtained from the depleted core of an operating boiling water reactor (BWR), which is more complicated than a pressurized water reactor to calculate because of the existence of coolant void distributions and cruciform control blades. Furthermore, measured bundles include mixed-oxide (MOX) bundles in which steep thermal flux gradients occur. Both UO 2 and MOX bundles have been calculated in the same manner based on the standard CASMO-3/SIMULATE-3 methods. The total pin power root-mean-square (rms) error is 2.7%, which includes measurement error, from an 896-point comparison. There is no obvious dependency on axial elevations (void fractions) and no significant difference between fuel types (UO 2 or MOX), although the errors in a peripheral bundle, which is less important from the standpoint of core design, are somewhat larger than those in the internal bundles. If the peripheral bundle is excluded, the total rms error is reduced to 2.2%. From these results, it is concluded that excellent agreement has been obtained between the calculations and measurements and that the calculational capability of CASMO-3/SIMULATE-3 for the intranodal pin power distribution is quite satisfactory and useful for BWR core design
Analisis Value Chain Di Industri Otomotif
Hendri, Hendri
2017-01-01
Penelitian ini untuk menganalisis industri otomotif. Tujuan dari penelitian ini adalah untuk menganalisis dan mengetahui aktivitas dan kondisi internal proses industri manufaktur dengan menggunakan value chain guna masukan dimasa akan datang bagi industri otomotif secara khusus. Value Chain merupakan rantai nilai yang dapat mengetahui kekuatan Perusahaan, keuntungan dan kesuksesan dari rantai aktivitas dalam Perusahaan atau industri manufaktur.Metode analisis menggunakan Statistika Deskript...
FFTF/IEM cell fuel pin weighing system
International Nuclear Information System (INIS)
Gibbons, P.W.
1987-01-01
The Interim Examination and Maintenance (IEM) cell in the Fast Flux Test Facility (FFTF) is used for remote disassembly of irradiated fuel and materials experiments. For those fuel experiments where the FFTF tag-gas detection system has indicated a fuel pin cladding breach, a weighing system is used in identifying that fuel pin with a reduced weight due to the escape of gaseous and volatile fission products. A fuel pin weighing machine, originally purchased for use in the Fuels and Materials Examination Facility (FMEF), was the basis for the IEM cell system. Design modifications to the original equipment were centered around adapting the machine to the differences between the two facilities and correcting deficiencies discovered during functional testing in the IEM cell mock-up
The Analisis Sentimen Sosial Media Twitter Dengan Algoritma Machine Learning Menggunakan Software R
Directory of Open Access Journals (Sweden)
Jaka Aulia Pratama
2017-10-01
Full Text Available Media sosial adalah wadah untuk mengungkapkan opini terhadap suatu topik tertentu. Ketersediaan informasi dan opini dari para pengguna media sosial merupakan kumpulan dokumen data berupa teks yang amat sangat besar dan berguna untuk kepentingan penelitian maupun membuat suatu keputusan bagi pihak – pihak tertentu. Text Mining bisa didefinisikan sebagai proses penggalian informasi di mana pengguna berinteraksi dengan kumpulan dokumen dari waktu ke waktu dengan menggunakan suatu alat analisis. Analisis sentimen atau Opinion Mining adalah salah satu studi di bidang komputasi yang berhubungan dengan kasus publik mengenai opini, penilaian, sikap, dan emosi. Penelitian ini akan menggunakan metode Machine Learning pada analisis sentimen pengguna layanan jejaring sosial Twitter terhadap Donald Trump dan Barack Obama dalam 20000 tweets. Nilai akurasi metode Machine Learning yang diperoleh cukup tinggi yaitu 87.52% untuk Data Training dan 87.4% untuk Data Testing.
Energy Technology Data Exchange (ETDEWEB)
Nunez McLeod, J E; Rivera, S S [Universidad Nacional de Cuyo, Mendoza (Argentina). Instituto de Capacitacion Especial y Desarrollo de Ingenieria Asistida por Computadora (CEDIAC)
1997-07-01
This work presents a methodology for sensitivity and uncertainty analysis, applicable to a probabilistic safety assessment level I. The work contents are: correct association of distributions to parameters, importance and qualification of expert opinions, generations of samples according to sample sizes, and study of the relationships among system variables and system response. A series of statistical-mathematical techniques are recommended along the development of the analysis methodology, as well different graphical visualization for the control of the study. (author) [Spanish] En este trabajo se presenta una metodologia de analisis de sensibilidad e incertidumbres, aplicable a un analisis probabilistico de seguridad (APS) de nivel I. En el cual se plantea: la adecuada asociacion de distribuciones a variables, la importancia y penalizacion de la opinion de expertos, la generacion de muestras y su tamano, y el estudio de las relaciones entre las variables del sistema y la respuesta de este. Ademas durante el desarrollo de la metodologia de analisis se recomiendan una serie de tecnicas estadistico-matematicas y tipos de visualizacion grafica para el control del estudio. (autor)
Self-organized critical behavior in pinned flux lattices
International Nuclear Information System (INIS)
Pla, O.; Nori, F.
1991-01-01
We study the response of pinned fluxed lattices, under small perturbations in the driving force, below and close to the pinning-depinning transition. For driving Lorentz forces below F c (the depinning force at which the whole flux lattice slides), the system has instabilities against small force increases, with a power-law distribution characteristic of self-organized criticality. Specifically, D(d)∼d -1,3 , where d is the displacement of a flux line after a very small force increase. We also study the initial stages of the motion of the lattice once the driving force overcomes the pinning forces
Fuel pin design algorithm for conceptual design studies
International Nuclear Information System (INIS)
Uselman, J.P.
1979-01-01
Two models are available which are currently verified by part of the requirements and which are adaptable as algorithms for the complete range. Fuel thermal performance is described by the HEDL SIEX model. Cladding damage and total deformation are determined by the GE GRO-II structural analysis code. A preliminary fuel pin performance model for analysis of (U, P/sub U/)O 2 pins in the COROPT core conceptual design system has been constructed by combining the key elements of SIEX and GRO-II. This memo describes the resulting pin performance model and its interfacing with COROPT system. Some exemplary results are presented
Analyzing the use of pins in safety bearings
DEFF Research Database (Denmark)
da Fonseca, Cesar A. L. L.; Weber, Hans I.; Fleischer, Philip F.
2015-01-01
A new concept for safety bearings is analyzed: useful in emergency situations, it shall protect the bearing from destruction by the use of pins which impact with a disc, both capable of good energy dissipation. Results of work in progress are presented by validating partial stages......–Kutta method is validated with experimental results. Simulations of rotor orbits due to the impact condition are analyzed and compared to data obtained from the experiment giving a good perspective on the use of pins. The contact interaction between rotor and pins uses an elastic-dissipative model. In addition...
Nominal power density analysis of thermoelectric pins with non-constant cross sections
International Nuclear Information System (INIS)
Shi, Yaoguang; Mei, Deqing; Yao, Zhehe; Wang, Yancheng; Liu, Haiyan; Chen, Zichen
2015-01-01
Highlights: • Nominal power density of TEGs with non-constant cross sections pins is analyzed. • An analytical model of nominal power density (NPD) is developed. • Influences of shape parameter on NPD for different geometric pins are investigated. • Effects of dimensionless efficiency and the temperature ratio on NPD are examined. - Abstract: The investigation of the geometric structure of TEG (thermoelectric generator) pins is essential, as their geometry determines the performance of devices. In this study, nominal power density (NPD) is used to find a better geometric structure of thermoelectric pins of TEGs, since a comparison of maximum dimensionless efficiencies for different geometric pins cannot be used to identify the optimum geometry. The influence of shape parameter on NPD for TEG pins in linear, quadratic and exponential cross-sectional functions is studied. The NPD decreases when the shape parameter increases for different geometric pins, while the maximum values of NPD are the same. Then, the effects of dimensionless efficiency and the temperature ratio on the NPD are analyzed. The NPD decreases with the increase in dimensionless efficiency and temperature ratio. Pins with linear variation in cross section have the highest NPD among the three geometries of pins evaluated
Some aspects of continuum physics used in fuel pin modeling
International Nuclear Information System (INIS)
Bard, F.E.
1975-06-01
The mathematical formulation used in fuel pin modeling is described. Fuel pin modeling is not a simple extension of the experimental and interpretative methods used in classical mechanics. New concepts are needed to describe materials in a reactor environment. Some aspects of continuum physics used to develop these new constitutive equations for fuel pins are presented. (U.S.)
Excessive Cellular S-nitrosothiol Impairs Endocytosis of Auxin Efflux Transporter PIN2
Directory of Open Access Journals (Sweden)
Min Ni
2017-11-01
Full Text Available S-nitrosoglutathione reductase (GSNOR1 is the key enzyme that regulates cellular levels of S-nitrosylation across kingdoms. We have previously reported that loss of GSNOR1 resulted in impaired auxin signaling and compromised auxin transport in Arabidopsis, leading to the auxin-related morphological phenotypes. However, the molecular mechanism underpinning the compromised auxin transport in gsnor1-3 mutant is still unknown. Endocytosis of plasma-membrane (PM-localized efflux PIN proteins play critical roles in auxin transport. Therefore, we investigate whether loss of GSNOR1 function has any effects on the endocytosis of PIN-FORMED (PIN proteins. It was found that the endocytosis of either the endogenous PIN2 or the transgenically expressed PIN2-GFP was compromised in the root cells of gsnor1-3 seedlings relative to Col-0. The internalization of PM-associated PIN2 or PIN2-GFP into Brefeldin A (BFA bodies was significantly reduced in gsnor1-3 upon BFA treatment in a manner independent of de novo protein synthesis. In addition, the exogenously applied GSNO not only compromised the endocytosis of PIN2-GFP but also inhibited the root elongation in a concentration-dependent manner. Taken together, our results indicate that, besides the reduced PIN2 level, one or more compromised components in the endocytosis pathway could account for the reduced endocytosis of PIN2 in gsnor1-3.
Positioning and locking device for fuel pin to grid attachment
International Nuclear Information System (INIS)
Frick, T.M.; Wineman, A.L.
1976-01-01
A positioning and locking device for fuel pin to grid attachment provides an inexpensive means of positively positioning and locking the individual fuel pins which make up the driver fuel assemblies used in nuclear reactors. The device can be adapted for use with a currently used attachment grid assembly design and insures that the pins remain in their proper position throughout the in-reactor life of the assembly. This device also simplifies fuel bundle assembly in that a complete row of fuel pins can be added to the bundle during each step of assembly. 8 claims, 8 drawing figures
Exchange anisotropy pinning of a standing spin-wave mode
Magaraggia, R.; Kennewell, K.; Kostylev, M.; Stamps, R. L.; Ali, M.; Greig, D.; Hickey, B. J.; Marrows, C. H.
2011-02-01
Standing spin waves in a thin film are used as sensitive probes of interface pinning induced by an antiferromagnet through exchange anisotropy. Using coplanar waveguide ferromagnetic resonance, pinning of the lowest energy spin-wave thickness mode in Ni80Fe20/Ir25Mn75 exchange-biased bilayers was studied for a range of Ir25Mn75 thicknesses. We show that pinning of the standing mode can be used to amplify, relative to the fundamental resonance, frequency shifts associated with exchange bias. The shifts provide a unique “fingerprint” of the exchange bias and can be interpreted in terms of an effective ferromagnetic film thickness and ferromagnet-antiferromagnet interface anisotropy. Thermal effects are studied for ultrathin antiferromagnetic Ir25Mn75 thicknesses, and the onset of bias is correlated with changes in the pinning fields. The pinning strength magnitude is found to grow with cooling of the sample, while the effective ferromagnetic film thickness simultaneously decreases. These results suggest that exchange bias involves some deformation of magnetic order in the interface region.
IMp: The customizable LEGO® Pinned Insect Manipulator
Directory of Open Access Journals (Sweden)
Steen Dupont
2015-02-01
Full Text Available We present a pinned insect manipulator (IMp constructed of LEGO® building bricks with two axes of movement and two axes of rotation. In addition we present three variants of the IMp to emphasise the modular design, which facilitates resizing to meet the full range of pinned insect specimens, is fully customizable, collapsible, affordable and does not require specialist tools or knowledge to assemble.
IMp: The customizable LEGO® Pinned Insect Manipulator
Dupont, Steen; Price, Benjamin; Blagoderov, Vladimir
2015-01-01
Abstract We present a pinned insect manipulator (IMp) constructed of LEGO® building bricks with two axes of movement and two axes of rotation. In addition we present three variants of the IMp to emphasise the modular design, which facilitates resizing to meet the full range of pinned insect specimens, is fully customizable, collapsible, affordable and does not require specialist tools or knowledge to assemble. PMID:25685035
International Nuclear Information System (INIS)
Gajapathy, R.; Velusamy, K.; Selvaraj, P.; Chellapandi, P.; Chetal, S.C.
2009-01-01
Preliminary investigations of sodium flow and temperature distributions in heat generating fuel pin bundles with helical spacer wires have been carried out. Towards this, the 3D conservation equations of mass, momentum and energy have been solved using a commercial computational fluid dynamics (CFD) code. Turbulence has been accounted through the use of high Reynolds number version of standard k-ε model, with uniform mesh density respecting wall function requirements. The geometric details of the bundle and the heat flux in are similar to that of the Indian Prototype Fast Breeder Reactor (PFBR) that is currently under construction. The mixing characteristics of the flow among the peripheral and central zones are compared for 7, 19 and 37 fuel pin bundles and the characteristics are extended to a 217 pin bundle. The friction factors of the pin bundles obtained from the present study is seen to agree well with the values derived from experimental correlations. It is found that the normalized outlet velocities in the peripheral and central zones are nearly equal to 1.1-0.9, respectively which is in good agreement with the published hydraulic experimental measurements of 1.1-0.85 for a 91 pin bundle. The axial velocity is the maximum in the peripheral zone where spacer wires are located and minimum in the zones which are diametrically opposite to the respective zone of maximum velocity. The sodium temperature is higher in the zones where the flow area and mass flow rates are less due to the presence of the spacer wires though the axial velocity is higher there. It is the minimum in the peripheral zones where the circumferential flow is larger. Based on the flow and temperature distributions obtained for 19 and 37 pin bundles, a preliminary extrapolation procedure has been established for estimating the temperatures of peripheral and central zones of 217 pin bundle.
Development of disassembly and pin chopping technology for FBR spent fuels
International Nuclear Information System (INIS)
Kobayashi, Tsuguyuki; Namba, Takashi; Kawabe, Yukinari; Washiya, Tadahiro
2008-01-01
Japan Atomic Power Company (JAPC) and Japan Atomic Energy Agency (JAEA) have been developing fuel disassembly and fuel pin chopping systems for a future Japanese commercial FBR. At first, the wrapper tube is cut by the slit-cut to pull it out, then the fuel pins are cut by the crop-cut at their end-plugs to separate them from the entrance nozzle. The pins are transferred to the magazine of the chopping machine. A series of tests were performed to develop this procedure. As the result of mechanical cutting tests, the CBN wheel was selected. The slit-cut tests were carried out to evaluated the cutting performance of the wheel. The wrapper tube is normally slit-cut in the circumferential direction. One CBN wheel could cut more than 5 fuel assemblies in this direction. The slit-cut in the axial direction is prepared as provision when the tube is difficult to put out. More work is needed to cut 5mm thick PNC-FMS plate in this direction without damaging the pins beneath it. As the result of the crop-cut tests of end-plugs made of ODS steel, the CBN wheel could cut the 61 pin bundle by two strokes. More work is needed to cut the 217 pin bundle. Fuel pin handling tests were performed to transfer them from the disassembly machine to the chopping machine. The Saucer tray was selected to receive the disassembled pins. All the pins were transferred and loaded into a magazine of the chopping machine. Fuel pin loading tests were conducted to optimize the magazine configuration to make the chopping length within 1.0±0.5 cm. In order to decrease the disturbance during chopping, the width of the magazine was adjusted to be 12 cm and installation of a height adjuster is favourable to control the free space above the pins. (author)
International Nuclear Information System (INIS)
Linde, A. van der; Lucas Luijckx, H.J.B.; Verheugen, J.H.N.
1982-01-01
The document reports in detail the fuel pin fabrication data and describes the irradiation conditions and history. All the relevant results of the non-destructive and destructive post-irradiation examinations are reported. They include: visual inspection and chemical analysis of crud; length and diameter measurements; neutron radiography and gamma scanning; juncture tests and fission gas analysis (including residual gas in fuel samples); microscopy and alpha + beta/gamma autoradiography; microprobe investigations; burn-up and isotopic analysis; and hydrogen analysis in clad. The data and observations obtained are discussed in detail and conclusions are given. The irradiation and post-irradiation examinations of the R-109 pins have shown the safe, pre-calculable performance of LWR fuel pins containing mixed-oxide sphere-pac fuel with the fissile material mainly present in the large spheres
Gamma scanning of mixed carbide and oxide fuel pins irradiated in FBTR
International Nuclear Information System (INIS)
Jayaraj, V.V.; Padalakshmi, M.; Ulaganathan, T.; Venkiteswaran, C.N.; Divakar, R.; Joseph, Jojo; Bhaduri, A.K.
2016-01-01
Fission in nuclear fuels results in a number of fission products that are gamma emitters in the energy range of 100 keV to 3 MeV. The gamma emitting fission products are therefore amenable for detection by gamma detectors. Assessment of the fission product distribution and their migration behavior through gamma scanning is important for characterizing the in reactor behavior of the fuel. Gamma scanning is an important non destructive technique used to evaluate the behavior of irradiated fuels. As a part of Post Irradiation Examinations (PIE), axial gamma scanning has been carried out on selected fuel pins of the FBTR Mark I mixed carbide fuel sub-assemblies and PFBR MOX test fuel sub-assembly irradiated in FBTR. This paper covers the results of gamma scanning and correlation of gamma scanning results with other PIE techniques
The PIN family of proteins in potato and their putative role in tuberisation
Directory of Open Access Journals (Sweden)
Efstathios eRoumeliotis
2013-12-01
Full Text Available The PIN family of trans-membrane proteins mediates auxin efflux throughout the plant and during various phases of plant development. In Arabidopsis thaliana, the PIN family comprised of 8 members, divided into ‘short’ and ‘long’ PINs according to the length of the hydrophilic domain of the protein. Based on sequence homology using the recently published potato genome sequence (Solanum tuberosum group Phureja we identified ten annotated potato StPIN genes. Mining the publicly available gene expression data, we constructed a catalogue tissue specificity of StPIN gene expression, focusing on the process of tuberization. A total of four StPIN genes exhibited increased expression four days after tuber induction, prior to the onset of stolon swelling. For two PIN genes, StPIN4 and StPIN2, promoter sequences were cloned and fused to the GUS reporter protein to study tissue specificity in more detail. StPIN4 promoter driven GUS staining was detected in the flower stigma, in the flower style, below the ovary and petals, in the root tips, in the vascular tissue of the stolons and in the tuber parenchyma cells. StPIN2 promoter driven GUS staining was detected in flower buds, in the vascular tissue of the swelling stolons and in the storage parenchyma of the growing tubers. Based on our results, we postulate a role for the StPINs in redistributing auxin in the swelling stolon during early events in tuber development.
Thermal performance of fresh mixed-oxide fuel in a fast flux LMR [liquid metal reactor
International Nuclear Information System (INIS)
Ethridge, J.L.; Baker, R.B.
1985-01-01
A test was designed and irradiated to provide power-to-melt (heat generation rate necessary to initiate centerline fuel melting) data for fresh mixed-oxide UO 2 -PuO 2 fuel irradiated in a fast neutron flux under prototypic liquid metal reactor (LMR) conditions. The fuel pin parameters were selected to envelope allowable fabrication ranges and address mass production of LMR fuel using sintered-to-size techniques. The test included fuel pins with variations in fabrication technique, pellet density, fuel-to-cladding gap, Pu concentration, and fuel oxygen-to-metal ratios. The resulting data base has reestablished the expected power-to-melt in mixed-oxide fuels during initial reactor startup when the fuel temperatures are expected to be the highest. Calibration of heat transfer models of fuel pin performance codes with these data are providing more accurate capability for predicting steady-state thermal behavior of current and future mixed-oxide LMR fuels
Application of PIN diodes in Physics Research
International Nuclear Information System (INIS)
Ramirez-Jimenez, F. J.; Mondragon-Contreras, L.; Cruz-Estrada, P.
2006-01-01
A review of the application of PIN diodes as radiation detectors in different fields of Physics research is presented. The development and research in semiconductor technology, the use of PIN diodes in particle counting, X-and γ-ray spectroscopy, medical applications and charged particle spectroscopy are considered. Emphasis is made in the activities realized in the different research and development Mexican institutions dealing with this kind of radiation detectors
Anisotropic flux pinning in high Tc superconductors
International Nuclear Information System (INIS)
Kolesnik, S.; Igalson, J.; Skoskiewicz, T.; Szymczak, R.; Baran, M.; Pytel, K.; Pytel, B.
1995-01-01
In this paper we present a comparison of the results of FC magnetization measurements on several Pb-Sr-(Y,Ca)-Cu-O crystals representing various levels of flux pinning. The pinning centers in our crystals have been set up during the crystal growth process or introduced by neutron irradiation. Some possible explanations of the observed effects, including surface barrier, flux-center distribution and sample-shape effects, are discussed. ((orig.))
Automation of FBTR fuel pin inspection using FPGA
International Nuclear Information System (INIS)
Khare, K.M.; Pai, Siddhesh; Pant, Brijesh; Sendhil Raja, S.; Gupta, P.K.
2011-01-01
A non-contact metrology system for inspection of FBTR fuel pins has been developed. The system consists of a stepper motors driven mechanism for orientation and positioning of FBTR fuel pin, a telecentric imaging system, absolute linear encoder with 0.1 μm resolution and a Field Programmable Gate Array (FPCA) based controller. The FBTR pin assembly is telecentrically illuminated from bottom by a red LED and its shadow graph is imaged using a CCD camera through telecentric imaging lens system. For system control and automation we have used a FPGA that has integrated soft picoblaze processor, X-θ axis motion controller, custom IPs for encoder data acquisition, synchronization circuit, RS485 interface along with other l/Os. Using the Graphical User Interface (GUI) on a PC the system is initialized at home position and the controller provides the trigger signal for start of data acquisition of CCD camera. CCD image of pin and the corresponding X-θ information is captured. After the acquisition of one set of images, the imaging module is moved with a step size pre-programmed to ensure proper stitching of acquired images. The GUI is programmed to analyze these X-θ Images to calculate the required parameters of the fuel pin like the diameter variation, pitch and bow. The details of the instrument and measurements made with it will be presented. (author)
Analisis Kebijakan dan Efektivitas Organisasi
Directory of Open Access Journals (Sweden)
Amir Syarifudin Kiwang
2015-05-01
Full Text Available Penerapan Peraturan Gubernur Nusa Tenggara Timur Nomor 8 Tahun 2011 tentang Organisasi dan Tata Kerja Unit Pelaksana Teknis Pendidikan dan Pelatihan Koperasi dan Usaha Mikro Kecil dan Menengah pada Dinas Koperasi dan Usaha Mikro Kecil dan Menengah Provinsi Nusa Tenggara Timur adalah dalam rangka untuk meningkatkan efektivitas kerja organisasi pada UPT Diklat Koperasi dan UMKM. Penelitian ini berusaha untuk melihat dampak kebijakan organisasi terhadap efektivitas organisasi dengan menggunakan enam elemen variabel dari kebijakan dan praktik manajemen. Keenam elemen tersebut adalah penetapan tujuan strategis, pencarian dan pemanfaatan sumber daya, lingkungan prestasi, proses komunikasi, kepemimpinan dan pengambilan keputusan, serta adaptasi dan inovasi organisasi. Penelitian kualitatif ini menggunakan pendekatan studi kasus. Teknik analisis data yang digunakan adalah analisis data model Miles dan Huberman, yang terdiri atas reduksi data, display/penyajian data, dan kesimpulan/verifikasi. Hasil penelitian menunjukkan bahwa efektivitas organisasi pada UPT Diklat koperasi dan UMKM belum berjalan secara baik, hal ini dapat dilihat dari beberapa hal antara lain, belum adanya tenaga spesialisasi pengelola diklat dan tenaga khusus (sarjana di bidang perkoperasian dan kondisi lingkungan kerja (lingkungan prestasi pada UPT Diklat koperasi dan UMKM yang belum efektif. Penempatan pegawai juga belum tepat, mutasi ke UPT Diklat Koperasi dan UMKM tidak memperhatikan latar belakang pendidikan dan spesialisasi/keahlian pegawai sehingga membutuhkan waktu dalam proses penyesuaian serta menurunkan jumlah pelaksanaan diklat dikarenakan keterbatasan alokasi dana.
Energy Technology Data Exchange (ETDEWEB)
Takiguchi, M; Suhara, T; Ato, S; Someya, T [Musashi Institute of Technology, Tokyo (Japan)
1997-10-01
Piston pin bearings are engine parts placed under severe lubricating condition because of the high unit load and temperature and the low sliding speeds. Therefore, they are vulnerable to many lubrication problems such as abnormal wear, scuffs and seizures. In our recent study, the bearing friction were measured using a original measuring device and it was found out that the lubricating conditions of piston pin boss bearings are non-fluid lubrication due to the oil starvation. In this study, we have also measured the lubricating oil behavior around the pin boss bearing using a special cylinder with glass window, and analyzed the relationship between the friction force and the oil behavior at the pin boss bearings in a actual operating gasoline engine. 2 refs., 9 figs., 1 tab.
Juhász, István; Soukup, Lajos; Szentmiklóssy, Zoltán
2015-01-01
The pinning down number $ {pd}(X)$ of a topological space $X$ is the smallest cardinal $\\kappa$ such that for any neighborhood assignment $U:X\\to \\tau_X$ there is a set $A\\in [X]^\\kappa$ with $A\\cap U(x)\
Development of modeling tools for pin-by-pin precise reactor simulation
International Nuclear Information System (INIS)
Ma Yan; Li Shu; Li Gang; Zhang Baoyin; Deng Li; Fu Yuanguang
2013-01-01
In order to develop large-scale transport simulation and calculation method (such as simulation of whole reactor core pin-by-pin problem), the Institute of Applied Physics and Computational Mathematics developed the neutron-photon coupled transport code JMCT and the toolkit JCOGIN. Creating physical calculation model easily and efficiently can essentially reduce problem solving time. Currently, lots of visual modeling programs have been developed based on different CAD systems. In this article, the developing idea of a visual modeling tool based on field oriented development was introduced. Considering the feature of physical modeling, fast and convenient operation modules were developed. In order to solve the storage and conversion problems of large scale models, the data structure and conversional algorithm based on the hierarchical geometry tree were designed. The automatic conversion and generation of physical model input file for JMCT were realized. By using this modeling tool, the Dayawan reactor whole core physical model was created, and the transformed file was delivered to JMCT for transport calculation. The results validate the correctness of the visual modeling tool. (authors)
ANALISIS PERIKANAN HUHATE DI PERAIRAN LARANTUKA, FLORES
Directory of Open Access Journals (Sweden)
Mohamad Adha Akbar
2016-11-01
Full Text Available Informasi mengenai beberapa aspek perikanan huhate sangat diperlukan sebagai bahan untuk perencanaan pengelolaan perikanan yang berkelanjutan. Penelitian ini dilakukan di Larantuka, Flores Timur pada tahun 2014 dengan tujuan untuk menganalisis perikanan huhate sebagai salah satu tulang punggung perikanan TCT. Kegiatan penelitian diprioritaskan pada analisis unit alat tangkap, daerah penangkapan, komposisi hasil tangkapan dan estimasi Total Faktor Produktivitas (TFP perikanan huhate. Basis data pengukuran adalah himpunan data pendaratan dan observasi lapang. Hasil penelitian menunjukan bahwa karakteristik armada terdiri dari kapal yang terbuat dari fibreglass dengan kisaran bobot kapal 6 - 30 GT. Daerah penangkapan di sekitar perairan Laut Sawu dan Laut Flores. Hasil tangkapan utama didominansi oleh cakalang (Katsuwonus pelamis sebanyak 82%, juwana tuna (Thunnus spp. 17% dan tongkol (Auxis spp. 1% serta hasil tangkapan ikutan lemadang (Coryphaena hippurus dan marlin (Makaira spp. < 1%. Hasil analisis tangkapan per unit upaya (CPUE memberikan nilai rata-rata sebesar 1,1 ton/trip (0,4-1,7 ton/trip dengan nilai tertinggi terjadi pada Februari, sedangkan terendah terjadi pada Januari. Hasil penelitian menunjukkan terdapat hubungan yang signifikan antara tren bulanan CPUE dan nilai TFP.
ANALISIS PENGELOLAAN LINGKUNGAN PERMUKIMAN DI KABUPATEN SOPPENG
Directory of Open Access Journals (Sweden)
Bakhrani Rauf
2016-08-01
Full Text Available Penelitian ini bertujuan untuk mendeskripsikan pengelolaan lingkungan permukiman di Kabupaten Soppeng pada aspek: (1 penyediaan dan penanganan lahan terbuka hijau (open space; (2 penyediaan dan penanganan drainase; (3 penanganan sampah; (4 penyediaan dan penanganan pembuangan veses (septic tank. Jenis penelitian ini adalah penelitian kuantitatif dengan pendekatan survei. Sampel wailayah penelitian ini adalah satu RW di ibu kota kabupaten dan satu RW di desa yang dipilih dengan metode purpossive sampling, yaitu RW yang sudah maju di ibu kota kabupaten dan RW yang tertinggal di desa. Responden sebanyak 50 kepala keluarga yakni masing-masing 25 kepala keuarga di setiap RW, dipilih dengan systematic random sampling. Teknik pengumpulan data yang dilakukan adalah melakukan observasi langsung dan dilengkapi dengan wawancara terhadap responden. Analisis yang digunakan adalah analisis deskriptif. Hasil penelitian menunjukkan bahwa pengelolaan lingkungan permukiman di Kabupaten Soppeng pada aspek: (1 ketersediaan dan penanganan lahan terbuka hijau (open space ditemukan belum memadai; (2 ketersediaan drainase (air kotor dan air hujan ditemukan belum memadai; (3 Penanganan sampahbelum memadai; dan (4 penanganan veses dan penyediaan septic tankbelum memadai.
Energy Technology Data Exchange (ETDEWEB)
Cai Shuiming, E-mail: caishuiming2008@yahoo.com.c [Department of Mathematics, Shanghai University, Shanghai 200444 (China); Institute of System Biology, Shanghai University, Shanghai 200444 (China); Hao Junjun [Institute of System Biology, Shanghai University, Shanghai 200444 (China); He, Qinbin [Department of Mathematics, Taizhou University, Linhai 317000 (China); Institute of System Biology, Shanghai University, Shanghai 200444 (China); Liu Zengrong, E-mail: zrongliu@126.co [Department of Mathematics, Shanghai University, Shanghai 200444 (China) and Institute of System Biology, Shanghai University, Shanghai 200444 (China)
2011-05-09
The problem of synchronization for a class of complex delayed dynamical networks via pinning periodically intermittent control is considered in this Letter. Some novel and useful exponential synchronization criteria are obtained by utilizing the methods which are different from the techniques employed in the existing works, and the derived results are less conservative. Especially, the traditional assumptions on control width and time delays are released in our results. Moreover, a pinning scheme deciding what nodes should be chosen as pinned candidates and how many nodes are needed to be pinned for a fixed coupling strength is provided. A Barabasi-Albert network example is finally given to illustrate the effectiveness of the theoretical results. - Highlights: Pinning control problem of complex networks via intermittent control is investigated. The traditional assumptions on control width and time delays are removed. A scheme deciding what nodes should be chosen as pinned candidates is proposed. A scheme deciding how many nodes are needed to be pinned is provided.
Qu, Haibo; Knabe, Christine; Radin, Shula; Garino, Jonathan; Ducheyne, Paul
2015-09-01
Risk of infection is considerable in open fractures, especially when fracture fixation devices are used to stabilize the fractured bones. Overall deep infection rates of 16.2% have been reported. The infection rate is even greater, up to 32.2%, with external fixation of femoral fractures. The use of percutaneous implants for certain clinical applications, such as percutaneous implants for external fracture fixation, still represents a challenge today. Currently, bone infections are very difficult to treat. Very potent antibiotics are needed, which creates the risk of irreversible damage to other organs, when the antibiotics are administered systemically. As such, controlled, local release is being pursued, but no such treatments are in clinical use. Herein, the use of bactericidal micron-thin sol-gel films on metallic fracture fixation pins is reported. The data demonstrates that triclosan (2,4,4'-trichloro-2'-hydroxydiphenylether), an antimicrobial agent, can be successfully incorporated into micron-thin sol-gel films deposited on percutaneous pins. The sol-gel films continuously release triclosan in vitro for durations exceeding 8 weeks (longest measured time point). The bactericidal effect of the micron-thin sol-gel films follows from both in vitro and in vivo studies. Inserting percutaneous pins in distal rabbit tibiae, there were no signs of infection around implants coated with a micron-thin sol-gel/triclosan film. Healing had progressed normally, bone tissue growth was normal and there was no epithelial downgrowth. This result was in contrast with the results in rabbits that received control, uncoated percutaneous pins, in which abundant signs of infection and epithelial downgrowth were observed. Thus, well-adherent, micron-thin sol-gel films laden with a bactericidal molecule successfully prevented pin tract infection. Copyright © 2015 Elsevier Ltd. All rights reserved.
Evaluating Approaches to Rendering Braille Text on a High-Density Pin Display.
Morash, Valerie S; Russomanno, Alexander; Gillespie, R Brent; OModhrain, Sile
2017-10-13
Refreshable displays for tactile graphics are typically composed of pins that have smaller diameters and spacing than standard braille dots. We investigated configurations of high-density pins to form braille text on such displays using non-refreshable stimuli produced with a 3D printer. Normal dot braille (diameter 1.5 mm) was compared to high-density dot braille (diameter 0.75 mm) wherein each normal dot was rendered by high-density simulated pins alone or in a cluster of pins configured in a diamond, X, or square; and to "blobs" that could result from covering normal braille and high-density multi-pin configurations with a thin membrane. Twelve blind participants read MNREAD sentences displayed in these conditions. For high-density simulated pins, single pins were as quickly and easily read as normal braille, but diamond, X, and square multi-pin configurations were slower and/or harder to read than normal braille. We therefore conclude that as long as center-to-center dot spacing and dot placement is maintained, the dot diameter may be open to variability for rendering braille on a high density tactile display.
Failure analysis on false call probe pins of microprocessor test equipment
Tang, L. W.; Ong, N. R.; Mohamad, I. S. B.; Alcain, J. B.; Retnasamy, V.
2017-09-01
A study has been conducted to investigate failure analysis on probe pins of test modules for microprocessor. The `health condition' of the probe pin is determined by the resistance value. A test module of 5V power supplied from Arduino UNO with "Four-wire Ohm measurement" method is implemented in this study to measure the resistance of the probe pins of a microprocessor. The probe pins from a scrapped computer motherboard is used as the test sample in this study. The functionality of the test module was validated with the pre-measurement experiment via VEE Pro software. Lastly, the experimental work have demonstrated that the implemented test module have the capability to identify the probe pin's `health condition' based on the measured resistance value.
Enquiry into the Topology of Plasma Membrane-Localized PIN Auxin Transport Components.
Nodzyński, Tomasz; Vanneste, Steffen; Zwiewka, Marta; Pernisová, Markéta; Hejátko, Jan; Friml, Jiří
2016-11-07
Auxin directs plant ontogenesis via differential accumulation within tissues depending largely on the activity of PIN proteins that mediate auxin efflux from cells and its directional cell-to-cell transport. Regardless of the developmental importance of PINs, the structure of these transporters is poorly characterized. Here, we present experimental data concerning protein topology of plasma membrane-localized PINs. Utilizing approaches based on pH-dependent quenching of fluorescent reporters combined with immunolocalization techniques, we mapped the membrane topology of PINs and further cross-validated our results using available topology modeling software. We delineated the topology of PIN1 with two transmembrane (TM) bundles of five α-helices linked by a large intracellular loop and a C-terminus positioned outside the cytoplasm. Using constraints derived from our experimental data, we also provide an updated position of helical regions generating a verisimilitude model of PIN1. Since the canonical long PINs show a high degree of conservation in TM domains and auxin transport capacity has been demonstrated for Arabidopsis representatives of this group, this empirically enhanced topological model of PIN1 will be an important starting point for further studies on PIN structure-function relationships. In addition, we have established protocols that can be used to probe the topology of other plasma membrane proteins in plants. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.
Performance of electrical contact pins near a nuclear explosion
International Nuclear Information System (INIS)
Ragan, C.E.; Silbert, M.G.; Ellis, A.N.; Robinson, E.E.; Daddario, M.J.
1977-09-01
The pressures attainable in equation-of-state studies using nuclear-explosion-driven shock waves greatly exceed those that can be reached in normal laboratory conditions. However, the diagnostic instrumentation must survive in the high-radiation environment present near such an explosion. Therefore, a set of experiments were fielded on the Redmud event to test the feasibility of using electrical contact pins in this environment. In these experiments a 60-cm-high shield of boron-lead was placed on the rack lid approximately 1 m from the device. A sample consisting of slabs of molybdenum and 238 U was placed on top of the shield, and twelve electrical contact pins were embedded to five different depths in the materials. Five different multiplexing-charging circuits were used for the pins, and a piezoelectric quartz gauge was placed on top of the uranium to obtain an estimate of the fission-energy deposition. All of the charged pins survived the radiation and produced signals indicating shock arrival. The uncertainty in determining the pin-closure time was approximately 3 ns. The signal from the quartz gauge corresponded to a pressure that was consistent with the calculated neutron fluence
Pin failure modeling of the A series CABRI tests
International Nuclear Information System (INIS)
Young, M.F.; Portugal, J.L.
1978-01-01
The EXPAND pin fialure model, a research tool designed to model pin failure under prompt burst conditions, has been used to predict failure conditions for several of the A series CABRI tests as part of the United States participation in the CABRI Joint Project. The Project is an international program involving France, Germany, England, Japan, and the United States and has the goal of obtaining experimental data relating to the safety of LMFBR's. The A series, designed to simulate high ramp rate TOP conditions, initially utilizes single, fresh UO 2 pins of the PHENIX type in a flowing sodium loop. The pins are preheated at constant power in the CABRI reactor to establish steady state conditions (480 w/cm at the axial peak) and then subjected to a power pulse of 14 ms to 24 ms duration
International Nuclear Information System (INIS)
Mitsuyasu, T.; Ishii, K.; Hino, T.; Aoyama, M.
2009-01-01
Spectral history methods for pin-by-pin core analysis method using the three-dimensional direct response matrix have been developed. The direct response matrix is formalized by four sub-response matrices in order to respond to a core eigenvalue k and thus can be recomposed at each outer iteration in the core analysis. For core analysis, it is necessary to take into account the burn-up effect related to spectral history. One of the methods is to evaluate the nodal burn-up spectrum obtained using the out-going neutron current. The other is to correct the fuel rod neutron production rates obtained the pin-by-pin correction. These spectral history methods were tested in a heterogeneous system. The test results show that the neutron multiplication factor error can be reduced by half during burn-up, the nodal neutron production rates errors can be reduced by 30% or more. The root-mean-square differences between the relative fuel rod neutron production rate distributions can be reduced within 1.1% error. This means that these methods can accurately reflect the effects of intra- and inter-assembly heterogeneities during burn-up and can be used for core analysis. Core analysis with the DRM method was carried out for an ABWR quarter core and it was found that both thermal power and coolant-flow distributions were smoothly converged. (authors)
Directory of Open Access Journals (Sweden)
Hendrawan Setyo Warsito
2016-04-01
Full Text Available Kekuatan slab beton sangat dipengaruhi oleh jenis material yang dipakai. Jenis material yang dimaksud adalah material beton dengan menggunakan PC (Portland Cement dan penggunaan geopolimer dalam komposisi campuran slab beton. Beton geopolimer merupakan beton yang ramah lingkungan. Permasalahan lain yang timbul adalah letak roda pesawat tidak selalu berada pada titik yang sama disuatu permukaan slab beton apron. Pada tugas akhir ini dimaksudkan untuk menganalisis suatu slab beton yang dibebani roda pesawat dengan campuran variasi material beton dan variasi letak roda pesawat pada slab beton dengan program bantu metode elemen hingga. Dengan data pergerakan pesawat, spesifikasi apron bandara Juanda kondisi eksisting. Dilakukan perhitungan tebal slab beton menggunakan software FAARFIELD dan diperoleh tebal slab beton sebesar 442,5 mm. Dari analisis program bantu elemen hingga dapat diperoleh tegangan pada slab beton yang ditimbulkan oleh pembebanan roda pesawat. Hasil validasi dari analisis tegangan menggunakan program bantu elemen hingga dengan analisis Westergaard yaitu memiliki nilai tegangan yang hampir sama pada ketebalan slab beton 450mm. Nilai tegangan tiap-tiap material beton menunjukan nilai tebal slab beton yang diijinkan untuk tipe pesawat tertentu. Dari analisis menggunakan program bantu elemen hingga tebal slab beton yang diijinkan untuk material slab beton PC yaitu sebesar 425mm. Sedangkan untuk material beton geopolimer yaitu sebesar 415 mm.
Temperature dependent pinning landscapes in REBCO thin films
Jaroszynski, Jan; Constantinescu, Anca-Monia; Hu, Xinbo Paul
2015-03-01
The pinning landscapes of REBCO (RE=rare earth elements) thin films have been a topic of study in recent years due to, among other reasons, their high ability to introduce various phases and defects. Pinning mechanisms studies in high temperature superconductors often require detailed knowledge of critical current density as a function of magnetic field orientation as well as field strength and temperature. Since the films can achieve remarkably high critical current, challenges exist in evaluating these low temperature (down to 4.2 K) properties in high magnetic fields up to 30 T. Therefore both conventional transport, and magnetization measurements in a vibrating coil magnetometer equipped with rotating sample platform were used to complement the study. Our results clearly show an evolution of pinning from strongly correlated effects seen at high temperatures to significant contributions from dense but weak pins that thermal fluctuations render ineffective at high temperatures but which become strong at lower temperatures Support for this work is provided by the NHMFL via NSF DRM 1157490
Analisis Model Penelusuran Backward Chaining dalam Mendeteksi Tingkat Kecanduan Game pada Anak
Directory of Open Access Journals (Sweden)
Anastasya Latubessy
2017-10-01
Full Text Available Game addiction rate can be detected by applying expert system. This study developed a model of game addiction analysis using backward chaining. This model uses six types of game addiction behavior, among others, salience, euphoria, conflict, tolerance, withdrawal, relapse and reinstatement. Someone is said to be addicted to the game if it meets at least three types of game addiction behavior. Testing the validity of the model is done by testing the closeness of the agreement between the model analysis and expert analysis, resulting in a value of 0.78 which means having a strong agreement. Tingkat kecanduan game dapat dideteksi dengan mengaplikasikan sistem pakar. Penelitian ini mengembangkan model analisis tingkat kecanduan game menggunakan backward chaining. Model ini menggunakan enam jenis perilaku kecanduan game antara lain, salience, euphoria, conflict, tolerance, withdrawal, relapse dan reinstatement. Seseorang dikatakan kecanduan game jika memenuhi paling sedikit tiga jenis perilaku kecanduan game. Pengujian validitas model dilakukan dengan menguji keeratan kesepakatan antara analisis model dan analisis pakar, menghasilkan nilai 0,78 yang berarti memiliki keeratan kesepakatan kuat.
Radiation detectors of PIN type for X-rays
International Nuclear Information System (INIS)
Ramirez-Jimenez, F.J.
2003-01-01
In this laboratory session, tree experiments are proposed: the measurement of X-ray energy spectra from radioactive sources with a high resolution cooled Si-Li detector, with a room temperature PIN diode and the measurement of the response of a PIN diode to the intensity of X-rays of radio-diagnostic units. The spectra obtained with the Si-Li detector help to understand the energy distribution of X-rays and are used as a reference to compare the results obtained with the PIN diode. Measurements in medical X-ray machines are proposed. Low cost, simple electronic instruments and systems are used as tools to make measurements in X-ray units used in radio-diagnostic
Estetika Tari Minang dalam Kesenian Randai Analisis Tekstual-Kontekstual
Directory of Open Access Journals (Sweden)
Sri Rustiyanti
2013-03-01
Full Text Available ABSTRACT This paper reveals textual and contextual Randai, among other things, an analysis of Gerak Ga lombang Randai, an analysis of the character of Anak Randai, and at the end of the study series, to reveal the values contained in Randai as a cultural reality, which in principle is an inseparable part of the existence of Minangkabau community as the cultural support. The variety of motion used in Gerak Galombang Randai is not only a decoration of the motion beauty (tangible, but it also can be translated, as well as a symbol or emblem that has educational meanings (intangible, and can be an example of the daily life of the indigenous Minangkabau society. Keywords: Minang Dance aesthetic, Randai, textualcontextual analysis ABSTRAK Tulisan ini mengungkap teksual dan kontekstual Randai, di antaranya, analisis terhadap gerak galombang Randai, analisis karakter tokoh anak Randai, dan sebagai akhir dari rang- kaian penelitian ini, mengungkapkan nilai-nilai yang terdapat pada Randai sebagai realitas budaya, yang pada prinsipnya merupakan bagian yang tak dapat dipisahkan dari eksistensi masyarakat Minangkabau sebagai penyangga kebudayaan. Ragam gerak yang digunakan dalam gerak galombang Randai itu kiranya tidak hanya sekedar hiasan keindahan gerak be- laka (tangibel, namun ia dapat diterjemahkan, sekaligus merupakan simbol atau lambang yang bermakna mendidik (intangibel, dan dapat menjadi teladan dalam kehidupan se- hari-hari dalam masyarakat adat di Minangkabau. Kata Kunci: estetika Tari Minang, Randai, analisis tekstual-kontekstual
Vortex dynamics in type-II superconductors under strong pinning conditions
Thomann, A. U.; Geshkenbein, V. B.; Blatter, G.
2017-10-01
We study effects of pinning on the dynamics of a vortex lattice in a type-II superconductor in the strong-pinning situation and determine the force-velocity (or current-voltage) characteristic combining analytical and numerical methods. Our analysis deals with a small density np of defects that act with a large force fp on the vortices, thereby inducing bistable configurations that are a characteristic feature of strong pinning theory. We determine the velocity-dependent average pinning-force density 〈Fp(v ) 〉 and find that it changes on the velocity scale vp˜fp/η a03 , where η is the viscosity of vortex motion and a0 the distance between vortices. In the small pin-density limit, this velocity is much larger than the typical flow velocity vc˜Fc/η of the free vortex system at drives near the critical force density Fc=〈Fp(v =0 ) 〉 ∝npfp . As a result, we find a generic excess-force characteristic, a nearly linear force-velocity characteristic shifted by the critical force density Fc; the linear flux-flow regime is approached only at large drives. Our analysis provides a derivation of Coulomb's law of dry friction for the case of strong vortex pinning.
Parasitic nematodes modulate PIN-mediated auxin transport to facilitate infection.
Directory of Open Access Journals (Sweden)
Wim Grunewald
2009-01-01
Full Text Available Plant-parasitic nematodes are destructive plant pathogens that cause significant yield losses. They induce highly specialized feeding sites (NFS in infected plant roots from which they withdraw nutrients. In order to establish these NFS, it is thought that the nematodes manipulate the molecular and physiological pathways of their hosts. Evidence is accumulating that the plant signalling molecule auxin is involved in the initiation and development of the feeding sites of sedentary plant-parasitic nematodes. Intercellular transport of auxin is essential for various aspects of plant growth and development. Here, we analysed the spatial and temporal expression of PIN auxin transporters during the early events of NFS establishment using promoter-GUS/GFP fusion lines. Additionally, single and double pin mutants were used in infection studies to analyse the role of the different PIN proteins during cyst nematode infection. Based on our results, we postulate a model in which PIN1-mediated auxin transport is needed to deliver auxin to the initial syncytial cell, whereas PIN3 and PIN4 distribute the accumulated auxin laterally and are involved in the radial expansion of the NFS. Our data demonstrate that cyst nematodes are able to hijack the auxin distribution network in order to facilitate the infection process.
Parasitic nematodes modulate PIN-mediated auxin transport to facilitate infection.
Grunewald, Wim; Cannoot, Bernard; Friml, Jirí; Gheysen, Godelieve
2009-01-01
Plant-parasitic nematodes are destructive plant pathogens that cause significant yield losses. They induce highly specialized feeding sites (NFS) in infected plant roots from which they withdraw nutrients. In order to establish these NFS, it is thought that the nematodes manipulate the molecular and physiological pathways of their hosts. Evidence is accumulating that the plant signalling molecule auxin is involved in the initiation and development of the feeding sites of sedentary plant-parasitic nematodes. Intercellular transport of auxin is essential for various aspects of plant growth and development. Here, we analysed the spatial and temporal expression of PIN auxin transporters during the early events of NFS establishment using promoter-GUS/GFP fusion lines. Additionally, single and double pin mutants were used in infection studies to analyse the role of the different PIN proteins during cyst nematode infection. Based on our results, we postulate a model in which PIN1-mediated auxin transport is needed to deliver auxin to the initial syncytial cell, whereas PIN3 and PIN4 distribute the accumulated auxin laterally and are involved in the radial expansion of the NFS. Our data demonstrate that cyst nematodes are able to hijack the auxin distribution network in order to facilitate the infection process.
International Nuclear Information System (INIS)
Yilbas, Bekir Sami; Akhtar, S.S.; Sahin, A.Z.
2016-01-01
Thermal stress developed in thermoelectric generators is critical for long service applications. High temperature gradients, due to a large temperature difference across the junctions, causes excessive stress levels developed in the device pins and electrodes at the interfaces. In the present study, a thermoelectric generator with horizontal pin configuration is considered and thermal stress analysis in the device is presented. Ceramic wafer is considered to resemble the high temperature plate and copper electrodes are introduced at the pin junctions to reduce the electrical resistance between the pins and the high and low temperature junction plates during the operation. Finite element code is used to simulate temperature and stress fields in the thermoelectric generator. In the simulations, convection and radiation losses from the thermoelectric pins are considered and bismuth telluride pin material with and without tapering is incorporated. It is found that von Mises stress attains high values at the interface between the hot and cold junctions and the copper electrodes. Thermal stress developed in tapered pin configuration attains lower values than that of rectangular pin cross-section. - Highlights: • Different cold junction temperatures improves thermoelectric generator performance. • von Mises stress remains high across copper electrodes and hot junction ceramics. • von Mises stress reduces along pin length towards cold junction. • Pin tapering lowers stress levels in thermoelectric generator.
Fuel pin response to an overpower transient in an LMFBR
International Nuclear Information System (INIS)
Grosberg, A.J.; Head, J.L.
1979-01-01
This paper describes a method by which the ability of a whole-core code accurately to predict the time and location of the first fuel pin failures may be tested. The method involves the use of a relatively simple whole-core code to 'drive' a sophisticated fuel pin code, which is far too complex to be used within a whole-core code but which is potentially capable of modelling reliably the response of an individual fuel pin. The method cannot follow accurately the subsequent course of the transient because the simple whole-core code does not model the reactivity effects of events which may follow pin failure. The codes used were the simple whole-core code FUTURE and the fuel pin behaviour code FRUMP. The paper describes an application of the method to analyse a hypothetical LMFBR accident in which the control rods were assumed to be driven from the core at maximum speed, with all trip circuits failed. Taking 0.5% clad strain as a clad failure criterion, failure was predicted to occur at the top of the active core at about 10s into the transient. A repeat analysis, using an alternative clad yield criterion which is thought to be more realistic, indicated failure at the same position but 24s into the transient. This is after the onset of sodium boiling. Pin failure at the top of the core are likely to cause negative reactivity changes. In this hypothetical accident, pin failures are likely, therefore, to have a moderating effect on the course of the transient. (orig.)
Dynamic Phases in Driven Vortex Lattices in Superconductors with Periodic Pinning Arrays.
Reichhardt, C.; Olson, C. J.; Nori, F.
1997-03-01
In an extensive series of simulations of driven vortices interacting with periodic pinning arrays, an extremely rich variety of novel plastic flow phases, very distinct from those observed in random arrays, are found as a function of applied driving force. We show that signatures of the transitions between these different dynamical phases appear as pronounced jumps and dips in the I-V curves, coinciding with marked changes in the microscopic structure and flow behavior of the vortex lattice. When the number of vortices is greater than the number of pinning sites, we observe up to six distinct dynamical phases, including a pinned phase, a flow of interstitial vortices between pinned vortices, a disordered flow, a 1D flow along the pinning rows, and a homogeneous flow. By varying a wide range of microscopic pinning parameters, including pinning strength, size, density, and degree of ordering, as well as varying temperature and commensurability, we obtain a series of dynamic phase diagrams. nori>A short video will also be presented to highlight these different dynamic phases.
Electrical transport and pinning properties of Nb films with washboard-like nanostructures
Energy Technology Data Exchange (ETDEWEB)
Dobrovolskiy, Oleksandr V. [Physikalisches Institut Goethe-University, Frankfurt am Main (Germany); Department of Physics, Kharkiv National University (Ukraine); Begun, Evgeniya; Huth, Michael [Physikalisches Institut Goethe-University, Frankfurt am Main (Germany); Shklovskij, Valerij A. [Department of Physics, Kharkiv National University (Ukraine); Institute for Theoretical Physics NSC-KIPT, Kharkiv (Ukraine)
2013-07-01
A careful analysis of the magneto-transport properties of epitaxial nanostructured Nb thin films in the normal and the mixed state is performed. The nanopatterns were prepared by focused ion beam (FIB) milling. They provide a washboard-like pinning potential landscape for vortices in the mixed state and simultaneously cause a resistivity anisotropy in the normal state. Two matching magnetic fields for the vortex lattice with the underlying nanostructures have been observed. By applying these fields, the most likely pinning sites along which the flux lines move through the samples have been selected. By this, either the background isotropic pinning of the pristine film or the enhanced isotropic pinning originating from the nanoprocessing have been probed. Via an Arrhenius analysis of the resistivity data the pinning activation energies for three vortex lattice parameters have been quantified. The changes in the electrical transport and the pinning properties have been correlated with the results of the microstructural and topographical characterization of the FIB-patterned samples. The obtained results provide further insight into the pinning mechanisms at work in FIB-nanopatterned superconductors for fluxonic applications.
Generation of spiral waves pinned to obstacles in a simulated excitable system
Phantu, Metinee; Kumchaiseemak, Nakorn; Porjai, Porramain; Sutthiopad, Malee; Müller, Stefan C.; Luengviriya, Chaiya; Luengviriya, Jiraporn
2017-09-01
Pinning phenomena emerge in many dynamical systems. They are found to stabilize extreme conditions such as superconductivity and super fluidity. The dynamics of pinned spiral waves, whose tips trace the boundary of obstacles, also play an important role in the human health. In heart, such pinned waves cause longer tachycardia. In this article, we present two methods for generating pinned spiral waves in a simulated excitable system. In method A, an obstacle is set in the system prior to an ignition of a spiral wave. This method may be suitable only for the case of large obstacles since it often fails when used for small obstacles. In method B, a spiral wave is generated before an obstacle is placed at the spiral tip. With this method, a pinned spiral wave is always obtained, regardless the obstacle size. We demonstrate that after a transient interval the dynamics of the pinned spiral waves generated by the methods A and B are identical. The initiation of pinned spiral waves in both two- and three-dimensional systems is illustrated.
Wear studies on prosthetic materials using the pin-on-disc machine.
Wright, K W; Dobbs, H S; Scales, J T
1982-01-01
The wear of ultra high molecular weight polyethylene in combination with cobalt-chromium-molybdenum alloy was investigated by pin-on-disc experiments in which the alloy pin was loaded against the rotating polyethylene disc. In some experiments the pin was stationary, but in others it rotated about its axis. The effect of lubricant type, pin rotation, magnitude of the applied load, magnitude of the relative surface velocity, and disc storage in various environments was investigated. Wear of the polyethylene was assessed at 100 h intervals by both volumetric and gravimetric methods. Each experiment lasted 1000 h. It was concluded that of the lubricants tested bovine serum was the most suitable and that pin rotation produced more suitable polyethylene surfaces than did the stationary pin. The wear rate increased slightly with load (possibly owing to creep), was insensitive to speed, and was not affected by disc storage. The dynamic coefficient of friction increased with running tme. Results obtained by the two wear assessment methods were comparable and the reproducibility of the results was good.
75 MeV boron ion irradiation studies on Si PIN photodiodes
Energy Technology Data Exchange (ETDEWEB)
Prabhakara Rao, Y.P.; Praveen, K.C. [Department of Studies in Physics, University of Mysore, Manasagangotri, Mysore 570006 (India); Rejeena Rani, Y. [Integrated Circuits Division, Bharat Electronics Limited, Bangalore 560013, Karnataka (India); Tripathi, Ambuj [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Gnana Prakash, A.P., E-mail: gnanap@hotmail.com [Department of Studies in Physics, University of Mysore, Manasagangotri, Mysore 570006 (India)
2013-12-01
The highly sensitive silicon PIN photodiodes were fabricated to use in radiation environments. The Si PIN photodiodes are coated with 150 nm silicon dioxide (SiO{sub 2}) as anti-reflective (AR) coating. The presence of AR coating on the performance of irradiated PIN photodiodes is studied up to a total dose of 10 Mrad. The effects of 75 MeV boron (B{sup 5+}) ions and {sup 60}Co gamma radiation on the I–V, C–V and spectral responses of PIN photodiodes were studied systematically to understand the radiation tolerance of the devices. The 75 MeV B{sup 5+} irradiation results are compared with {sup 60}Co gamma irradiated results in the same dose range for 1 mm × 1 mm and 10 mm × 10 mm active area PIN photodiodes. The irradiation results show that the ion irradiated PIN photodiodes show more degradation when compared {sup 60}Co gamma irradiated devices. The irradiation results are presented in this paper and the possible mechanism behind the degradation of photodiodes is also discussed in the paper.
Development of vibropac MOX fuel pins serviceable up TP superhigh burnups
International Nuclear Information System (INIS)
Mayorshin, A.A.; Gadzhiev, G.I.; Kisly, V.A.; Skiba, O.V.; Tzykanov, V.A.
1998-01-01
The main results on investigations of fast reactor fuel pins with (UPu)O 2 vibropac fuel to substantiate their serviceability up to the super-high burnups are presented. The BOR-60 reactor fuel pins radiation behaviour in stationary, transient and designed emergency conditions has been determined from the fuel pins dimensional stability analysis having regard to the results of investigation fuel and cladding swelling as well as estimations of fuel and cladding thermal-mechanical and physico-chemical interactions. It is shown that the change of the outer diameter is minimum in fuel pins with VMOX fuel with a getter-metallic uranium powder and ferrito-martensite steel cladding, and the corrosion damage of the cladding inner surface is absent up to 26% h.a. The experiments with over-heating of the irradiated fuel pins cladding up to 850 deg. C did not lead to any changes in pins integrity. The availability of the periphery area of the vibropac fuel cure initial structure provides the minimum level of the thermal-mechanical stress at transient conditions of reactor operation. (author)
SP-100 Fuel Pin Performance: Results from Irradiation Testing
Makenas, Bruce J.; Paxton, Dean M.; Vaidyanathan, Swaminathan; Marietta, Martin; Hoth, Carl W.
1994-07-01
A total of 86 experimental fuel pins with various fuel, liner, and cladding candidate materials have been irradiated in the Experimental Breeder Reactor-II (EBR-II) and the Fast Flux Test Facility (FFTF) reactor as part of the SP-100 fuel pin irradiation testing program. Postirradiation examination results from these fuel pins are key in establishing performance correlations and demonstrating the lifetime and safety of the reactor fuel system. This paper provides a brief description of the in-reactor fuel pin tests and presents the most recent irradiation data on the performance of wrought rhenium (Re) liner material and high density UN fuel at goal burnup of 6 atom percent (at. %). It also provides an overview of the significant variety of other fuel/liner/cladding combinations which were irradiated as part of this program and which may be of interest to more advanced efforts.
PINS Testing and Modification for Explosive Identification
International Nuclear Information System (INIS)
Seabury, E.H.; Caffrey, A.J.
2011-01-01
The INL's Portable Isotopic Neutron Spectroscopy System (PINS)1 non-intrusively identifies the chemical fill of munitions and sealed containers. PINS is used routinely by the U.S. Army, the Defense Threat Reduction Agency, and foreign military units to determine the contents of munitions and other containers suspected to contain explosives, smoke-generating chemicals, and chemical warfare agents such as mustard and nerve gas. The objects assayed with PINS range from softball-sized M139 chemical bomblets to 200 gallon DOT 500X ton containers. INL had previously examined2 the feasibility of using a similar system for the identification of explosives, and based on this proof-of-principle test, the development of a dedicated system for the identification of explosives in an improvised nuclear device appears entirely feasible. INL has been tasked by NNSA NA-42 Render Safe Research and Development with the development of such a system.
ANALISIS PERBAIKAN SISTEM PENTANAHAN TELEKOMUNIKASI
Directory of Open Access Journals (Sweden)
Umar Umar
2015-04-01
Hasil dari penelitian ini adalah perbaikan sistem pentanahan site Kampung Baru dengan menggunakan konfigurasi single point connection window (SPCW, untuk mengamankan sistem telekomunikasi dari kebocoran arus dan petir serta imbasnya. Perbaikan sistem pentanahan di site Kampung Baru menggunakan banyak elektroda yang membentuk persegi dikarenakan topografi tempat di sana yang memungkinkan dan efektif adalah menggunakan sistem tersebut. Berdasarkan hasil analisis dan perhitungan perbaikan sistem di site Kampung Baru, didapatkan nilai perhitungan sistem pentanahan adalah 1.34 Ohm serta pengukurannya 1.21-1.25 Ohm.
Inverse crystallization if Abrikosov vortex system at periodic pinning
Zyubin, M V; Kashurnikov, V A
2002-01-01
The vortex system in the quasi-two-dimensional HTSC plate is considered in the case of the periodic pinning. The M(H) magnetization curves by various values of the external magnetic field and different temperatures are calculated through the Monte Carlo method. It is shown that in the case of the periodic pinning the crystallization of the vortex system is possible by the temperature increase. A number of peculiarities conditioned by the impact of the pinning centers periodic lattice are identified on the magnetization curves. The pictures of the vortex distribution corresponding to various points on the M(H) curve are obtained
Pinning in BSCCO above the ordinary irreversibility line
Indenbom, M. V.; van der Beek, C. J.; Berseth, V.; Konczykowski, M.; Motohira, N.; Berger, H.; Benoit, W.
1996-12-01
Frequency-dependent observations of magnetic flux structures are used to show that pinning plays a principal role in the whole mixed state in Bi2Sr2CaCu2O8 (BSCCO) single crystals. We speculate that the random pinning force on the moving vortices may dominate over thermal fluctuations and considerably modify the position of the vortex lattice phase transition.
IMp: The customizable LEGO(®) Pinned Insect Manipulator.
Dupont, Steen; Price, Benjamin; Blagoderov, Vladimir
2015-01-01
We present a pinned insect manipulator (IMp) constructed of LEGO® building bricks with two axes of movement and two axes of rotation. In addition we present three variants of the IMp to emphasise the modular design, which facilitates resizing to meet the full range of pinned insect specimens, is fully customizable, collapsible, affordable and does not require specialist tools or knowledge to assemble.
A Flux-Pinning Mechanism for Segment Assembly and Alignment
Gersh-Range, Jessica A.; Arnold, William R.; Peck, Mason A.; Stahl, H. Philip
2011-01-01
Currently, the most compelling astrophysics questions include how planets and the first stars formed and whether there are protostellar disks that contain large organic molecules. Although answering these questions requires space telescopes with apertures of at least 10 meters, such large primaries are challenging to construct by scaling up previous designs; the limited capacity of a launch vehicle bounds the maximum diameter of a monolithic primary, and beyond a certain size, deployable telescopes cannot fit in current launch vehicle fairings. One potential solution is connecting the primary mirror segments edgewise using flux-pinning mechanisms, which are analogous to non-contacting damped springs. In the baseline design, a flux-pinning mechanism consists of a magnet and a superconductor separated by a predetermined gap, with the damping adjusted by placing aluminum near the interface. Since flux pinning is possible only when the superconductor is cooled below a critical temperature, flux-pinning mechanisms are uniquely suited for cryogenic space telescopes. By placing these mechanisms along the edges of the mirror segments, a primary can be built up over time. Since flux pinning requires no mechanical deployments, the assembly process could be robotic or use some other non-contacting scheme. Advantages of this approach include scalability and passive stability.
Spatial chaotic behavior of vortices in type-II superconductors with different pinning strength
International Nuclear Information System (INIS)
Lin, H.-T.; Pan, M.; Cheng, C.H.; Cui, Y.J.; Zhao, Y.
2008-01-01
Spatial chaotic character in systems where defects are arranged in periodic arrays has been investigated by computer simulation. Due to the high nonlinearity of the vortex-defect interaction, arrangement of the vortices in a periodic pinning array can be chaotic (glassy), depending on the vortex-defect interaction state and vortex-vortex interaction. Two types of disordered vortex states in the system are observed. The type-I disorder arises from the intrinsically chaotic nature of the nonlinear system, existing when the pinning disorder is low and the pinning strength is weak. The type-II disordered state is related to the pinning disorder, which is dominating when both the pinning disorder and the pinning strength are strong
Spatial chaotic behavior of vortices in type-II superconductors with different pinning strength
Energy Technology Data Exchange (ETDEWEB)
Lin, H.-T. [Faculty of Information Management, Cheng Shui University, Taiwan (China); Pan, M. [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, Superconductivity R and D Center, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Cheng, C.H. [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, Superconductivity R and D Center, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney (Australia); Cui, Y.J. [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, Superconductivity R and D Center, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Zhao, Y. [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, Superconductivity R and D Center, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney (Australia)], E-mail: yzhao@swjtu.edu.cn
2008-09-15
Spatial chaotic character in systems where defects are arranged in periodic arrays has been investigated by computer simulation. Due to the high nonlinearity of the vortex-defect interaction, arrangement of the vortices in a periodic pinning array can be chaotic (glassy), depending on the vortex-defect interaction state and vortex-vortex interaction. Two types of disordered vortex states in the system are observed. The type-I disorder arises from the intrinsically chaotic nature of the nonlinear system, existing when the pinning disorder is low and the pinning strength is weak. The type-II disordered state is related to the pinning disorder, which is dominating when both the pinning disorder and the pinning strength are strong.
Generation of clusters in complex dynamical networks via pinning control
International Nuclear Information System (INIS)
Li Kezan; Fu Xinchu; Small, Michael
2008-01-01
Many real-world networks show community structure, i.e., groups (or clusters) of nodes that have a high density of links within them but with a lower density of links between them. In this paper, by applying feedback injections to a fraction of network nodes, various clusters are synchronized independently according to the community structure generated by the group partition of the network (cluster synchronization). This control is achieved by pinning (i.e. applying linear feedback control) to a subset of the network nodes. Those pinned nodes are selected not randomly but according to the topological structure of communities of a given network. Specifically, for a given group partition of a network, those nodes with direct connections between groups must be pinned in order to achieve cluster synchronization. Both the local stability and global stability of cluster synchronization are investigated. Taking the tree-shaped network and the most modular network as two particular examples, we illustrate in detail how the pinning strategy influences the generation of clusters. The simulations verify the efficiency of the pinning schemes used in this paper
Silicide Schottky Contacts to Silicon: Screened Pinning at Defect Levels
Energy Technology Data Exchange (ETDEWEB)
Drummond, T.J.
1999-03-11
Silicide Schottky contacts can be as large as 0.955 eV (E{sub v} + 0.165 eV) on n-type silicon and as large as 1.05 eV (E{sub c} {minus} 0.07 eV) on p-type silicon. Current models of Schottky barrier formation do not provide a satisfactory explanation of occurrence of this wide variation. A model for understanding Schottky contacts via screened pinning at defect levels is presented. In the present paper it is shown that most transition metal silicides are pinned approximately 0.48 eV above the valence band by interstitial Si clusters. Rare earth disilicides pin close to the divacancy acceptor level 0.41 eV below the conduction band edge while high work function silicides of Ir and Pt pin close to the divacancy donor level 0.21 eV above the valence band edge. Selection of a particular defect pinning level depends strongly on the relative positions of the silicide work function and the defect energy level on an absolute energy scale.
Pin1 and neurodegeneration: a new player for prion disorders?
Directory of Open Access Journals (Sweden)
Elisa Isopi
2015-07-01
Full Text Available Pin1 is a peptidyl-prolyl isomerase that catalyzes the cis/trans conversion of phosphorylated proteins at serine or threonine residues which precede a proline. The peptidyl-prolyl isomerization induces a conformational change of the proteins involved in cell signaling process. Pin1 dysregulation has been associated with some neurodegenerative disorders such as Alzheimer's disease, Parkinson's disease and Huntington's disease. Proline-directed phosphorylation is a common regulator of these pathologies and a recent work showed that it is also involved in prion disorders. In fact, prion protein phosphorylation at the Ser-43-Pro motif induces prion protein conversion into a disease-associated form. Furthermore, phosphorylation at Ser-43-Pro has been observed to increase in the cerebral spinal fluid of sporadic Creutzfeldt-Jakob Disease patients. These findings provide new insights into the pathogenesis of prion disorders, suggesting Pin1 as a potential new player in the disease. In this paper, we review the mechanisms underlying Pin1 involvement in the aforementioned neurodegenerative pathologies focusing on the potential role of Pin1 in prion disorders.
Finite Element Analysis of Laser Engineered Net Shape (LENS™) Tungsten Clad Squeeze Pins
Sakhuja, Amit; Brevick, Jerald R.
2004-06-01
In the aluminum high-pressure die-casting and indirect squeeze casting processes, local "squeeze" pins are often used to minimize internal solidification shrinkage in heavy casting sections. Squeeze pins frequently fail in service due to molten aluminum adhering to the H13 tool steel pins ("soldering"). A wide variety of coating materials and methods have been developed to minimize soldering on H13. However, these coatings are typically very thin, and experience has shown their performance on squeeze pins is highly variable. The LENS™ process was employed in this research to deposit a relatively thick tungsten cladding on squeeze pins. An advantage of this process was that the process parameters could be precisely controlled in order to produce a satisfactory cladding. Two fixtures were designed and constructed to enable the end and outer diameter (OD) of the squeeze pins to be clad. Analyses were performed on the clad pins to evaluate the microstructure and chemical composition of the tungsten cladding and the cladding-H13 substrate interface. A thermo-mechanical finite element analysis (FEA) was performed to assess the stress distribution as a function of cladding thickness on the pins during a typical casting thermal cycle. FEA results were validated via a physical test, where the clad squeeze pins were immersed into molten aluminum. Pins subjected to the test were evaluated for thermally induced cracking and resistance to soldering of the tungsten cladding.
Finite element analysis of laser engineered net shape (LENSTM) tungsten clad squeeze pins
International Nuclear Information System (INIS)
Sakhuja, Amit; Brevick, Jerald R.
2004-01-01
In the aluminum high-pressure die-casting and indirect squeeze casting processes, local 'squeeze' pins are often used to minimize internal solidification shrinkage in heavy casting sections. Squeeze pins frequently fail in service due to molten aluminum adhering to the H13 tool steel pins ('soldering'). A wide variety of coating materials and methods have been developed to minimize soldering on H13. However, these coatings are typically very thin, and experience has shown their performance on squeeze pins is highly variable. The LENS TM process was employed in this research to deposit a relatively thick tungsten cladding on squeeze pins. An advantage of this process was that the process parameters could be precisely controlled in order to produce a satisfactory cladding. Two fixtures were designed and constructed to enable the end and outer diameter (OD) of the squeeze pins to be clad. Analyses were performed on the clad pins to evaluate the microstructure and chemical composition of the tungsten cladding and the cladding-H13 substrate interface. A thermo-mechanical finite element analysis (FEA) was performed to assess the stress distribution as a function of cladding thickness on the pins during a typical casting thermal cycle. FEA results were validated via a physical test, where the clad squeeze pins were immersed into molten aluminum. Pins subjected to the test were evaluated for thermally induced cracking and resistance to soldering of the tungsten cladding
ANALISIS DAYA SAING KEDELAI INDONESIA
Directory of Open Access Journals (Sweden)
Sarwono Sarwono
2014-09-01
Full Text Available RCA (Revealed Comparative Advantage index of soybean in Indonesia from 1983 up to 2013 is less than one, mostly. It means that the competitiveness of soybean in Indonesia is low. The purpose of this study is to analyze the factors influence the soybean competitiveness. OLS (Ordinary Least Square was used as the analysis method. Hypotheses test based on that analysis model is not bias, so that, classic divergence test is needed. It is for getting the Best Linier Unbiased Estimator (BLUE appraisal. T statistic and F statistic were also applied. The result of this research shows that production and export have positive and significant influence. In addition, exchange rate and government policy do not influence the Indonesia soybean competitiveness.Indeks RCA (Revealed Comparative Advantage kedelai Indonesia dari tahun 1983-2013 kecenderungan bernilai kurang dari satu yang berarti daya saing kedelai Indonesia rendah.Penelitian ini bertujuan untuk menganalisis faktor-faktor yang mempengaruhi daya saing kedelai Indonesia.Metode analisis yang digunakan adalah Ordinary Least Square (OLS.Pengujian hipotesis berdasarkan model analisis tersebut tidak bias maka perlu dilakukan uji penyimpangan klasik yang tujuannya agar diperoleh penaksiran yang bersifat Best Linier Unbiased Estimator (BLUE.Pengujian statistik menggunakan uji t statistikdan uji f statistik.Hasil penelitian ini menunjukkan bahwa produksi dan ekspor berpengaruh secara positif dan signifikan terhadap daya saing kedelai Indonesia. Nilai tukar rupiah dan kebijakan pemerintah tidak berpengaruh terhadap daya saing kedelai Indonesia.
Sodium Loop Safety Facility W-2 experiment fuel pin rupture detection system
International Nuclear Information System (INIS)
Hoffman, M.A.; Kirchner, T.L.; Meyers, S.C.
1980-05-01
The objective of the Sodium Loop Safety Facility (SLSF) W-2 experiment is to characterize the combined effects of a preconditioned full-length fuel column and slow transient overpower (TOP) conditions on breeder reactor (BR) fuel pin cladding failures. The W-2 experiment will meet this objective by providing data in two technological areas: (1) time and location of cladding failure, and (2) early post-failure test fuel behavior. The test involves a seven pin, prototypic full-length fast test reactor (FTR) fuel pin bundle which will be subjected to a simulated unprotected 5 cents/s reactivity transient overpower event. The outer six pins will provide the necessary prototypic thermal-hydraulic environment for the center pin
International Nuclear Information System (INIS)
Haokip, Nemneineng; Naorem, Aruna
2017-01-01
Pin1-type parvulins are unique among PPIases that can catalyse an otherwise slow cis-trans isomerisation of phosphorylated peptide bond preceding proline in target proteins. This prolyl isomerisation process can regulate activity, stability and localisation of target proteins and thus control cellular processes like eukaryotic cell proliferation, cell cycle progression and gene regulation. Towards understanding the function of Pin1-type prolyl isomerisation in Dictyostelium discoideum, a slime mould with distinct growth and developmental phases, we identified PinA as a novel Pin1-type parvulin by its ability to complement the temperature sensitivity phenotype associated with a mutation in ESS1 in S. cerevisiae. In D. discoideum, pinA is temporally and spatially regulated during growth and development. PinA is both nuclear as well as cytoplasmic in the growing cells. We further show that loss of pinA (pinA − ) leads to decreased growth rate, reduced spore formation and abnormal prespore-prestalk patterning. We conclude that PinA is required for normal growth as well as development in D. discoideum. - Highlights: • PinA is a bona fide homologue of S. cerevisiae Ess1. • PinA is required for normal cell proliferation of D. discoideum. • PinA is spatially localised in developmental structures. • PinA is important for cell differentiation and patterning.
Crystallinity and flux pinning properties of MgB2 bulks
International Nuclear Information System (INIS)
Yamamoto, A.; Shimoyama, J.; Ueda, S.; Katsura, Y.; Iwayama, I.; Horii, S.; Kishio, K.
2006-01-01
The relationship between flux pinning properties and crystallinity of MgB 2 bulks was systematically studied. Improved flux pinning properties under high fields were observed for samples with low crystallinity. Increased impurity scattering due to strain and defects in lattice corresponding to the degraded crystallinity was considered to enhance flux pinning strength at grain boundaries. Low-temperature synthesis and carbon substitution were confirmed to be effective for degrading crystallinity of MgB 2 bulks, resulting in high critical current properties under high fields
Analisis Pengaruh Display Interior Terhadap Perilaku Pembelian Impulsif Konsumen Indomaret Pontianak
Directory of Open Access Journals (Sweden)
Ana Fitriana
2016-07-01
Full Text Available Pembelian impulsif adalah kecenderungan membeli produk atau jasa dengan tidak terencana, selanjutnya ketika pembelian sering tidak terencana, maka umumnya konsumen membeli produk atau jasa yang tidak terdaftar dalam daftar belanja. Sejalan dengan tujuan pemasar, pembelian tidak terencana ini berdampak sangat positif bagi pihak perusahaan. Salah satu perilaku konsumen yang sangat penting adalah perilaku belanja impulsif. Penelitian ini bertujuan untuk mengetahui pengaruh display interior pada Indomaret Pontianak terhadap impulsive buying konsumennya. Metode penelitian yang digunakan adalah penelitian kuantitatif. Populasi penelitian ini adalah konsumen Indomaret Pontianak, sebanyak 100 responden dipilih secara accidental sampling sebagai sampel penelitian. Metode pengumpulan data yang digunakan adalah metode pengumpulan data primer dengan teknik pengumpulan data kuesioner. Teknik analisis data yang digunakan adalah uji validitas dan reliabilitas, analisis koefisien determinasi, analisis regresi berganda dan uji hipotesis.Hasil perhitungan data menggunakan SPSS for windows ver 16 menunjukan secara simultan pengaruh display interior terhadap impulsive buying diketahui berpengaruh sebesar 61,31%. Sedangkan 38,69% dipengaruhi oleh faktor lain yang tidak diteliti didalam penelitian ini. Secara parsial tiga variabel bebas yaitu pengadaan barang, pengelompokan barang, dan penyusunan barang dan pencahayaan mempunyai pengaruh signifikan terhadap Impulsive buying. Kata kunci — Pengadaan barang, Pengelompokan barang, Penyusunan barang dan pencahayaan, Perilaku Pembelian Impulsif
Experimental and numerical study of Bondura® 6.6 PIN joints
Berkani, I.; Karlsen, Ø.; Lemu, H. G.
2017-12-01
Pin joints are widely used in heavy-duty machinery such as aircrafts, cranes and offshore drilling equipment to transfer multi-dimensional shear forces. Their strength and service life depend on the clamping force in the contact region that is provided by interference fits. Though the interference fits provide full contact at the pin-hole interface under pretension loads, the contact interface reduces when the pin is subjected to an external load and hence a smaller contact surface leads to dramatic increase of the contact stress. The PIN joint of Bondura® Technology, investigated in this study, is an innovative solution intended to reduce the slack at the contact surface of the pin joint of heavy-duty machinery by using tapered sleeves on each end of the PIN. The study is aimed to better understand the contact pressure build-up and stress distribution in the supporting contact surface under pre-loading of the joint and the influence of temperature difference between part assembly and operation conditions. Numerical simulation using finite element method and diverse experimental tests were conducted. The numerical simulation and the test results, particularly the tests conducted with lubricated joints, show good conformance.
Los Alamos Hot-Cell-Facility modifications for examining FFTF fuel pins
International Nuclear Information System (INIS)
Campbell, B.M.; Ledbetter, J.M.
1982-01-01
Commissioned in 1960, the Wing 9 Hot Cell Facility at Los Alamos was recently modified to meet the needs of the 1980s. Because fuel pins from the Fast Flux Test Facility (FFTF) at the Hanford Engineering Development Laboratory (HEDL) are too long for examination in the original hot cells, we modified cells to accommodate longer fuel pins and to provide other capabilities as well. For instance, the T-3 shipping cask now can be opened in an inert atmosphere that can be maintained for all nondestructive and destructive examinations of the fuel pins. The full-length pins are visually examined and photographed, the wire wrap is removed, and fission gas is sampled. After the fuel pin is cropped, a cap is seal-welded on the section containing the fuel column. This section is then transferred to other cells for gamma-scanning, radiography, profilometry, sectioning for metallography, and chemical analysis
Velocity distribution measurement in wire-spaced fuel pin bundle
International Nuclear Information System (INIS)
Mizuta, Hiroshi; Ohtake, Toshihide; Uruwashi, Shinichi; Takahashi, Keiichi
1974-01-01
Flow distribution measurement was made in the subchannels of a pin bundle in air flow. The present paper is interim because the target of this work is the decision of temperature of the pin surface in contact with wire spacers. The wire-spaced fuel pin bundle used for the experiment consists of 37 simulated fuel pins of stainless steel tubes, 3000 mm in length and 31.6 mm in diameter, which are wound spirally with 6 mm stainless steel wire. The bundle is wrapped with a hexagonal tube, 3500 mm in length and 293 mm in flat-to-flat distance. The bundle is fixed with knock-bar at the entrance of air flow in the hexagonal tube. The pitch of pins in the bundle is 37.6 mm (P/D=1.19) and the wrapping pitch of wire is 1100 mm (H/D=34.8). A pair of arrow-type 5-hole Pitot tubes are used to measure the flow velocity and the direction of air flow in the pin bundle. The measurement of flow distribution was made with the conditions of air flow rate of 0.33 m 3 /sec, air temperature of 45 0 C, and average Reynolds number of 15100 (average air velocity of 20.6 m/sec.). It was found that circular flow existed in the down stream of wire spacers, that axial flow velocity was slower in the subchannels, which contained wire spacers, than in those not affected by the wire, and that the flow angle to the axial velocity at the boundary of subchannels was two thirds smaller than wire wrapping angle. (Tai, I.)
Manoogian, Sarah; Lee, Adam K; Widmaier, James C
2017-08-01
No studies have assessed the effects of parameters associated with insertion temperature in modern self-drilling external fixation pins. The current study assessed how varying the presence of irrigation, insertion speed, and force impacted the insertion temperatures of 2 types of standard and self-drilling external fixation half pins. Seventy tests were conducted with 10 trials for 4 conditions on self-drilling pins, and 3 conditions for standard pins. Each test used a thermocouple inside the pin to measure temperature rise during insertion. Adding irrigation to the standard pin insertion significantly lowered the maximum temperature (P drilling pin tests dropped average rise in temperature from 151.3 ± 21.6°C to 124.1 ± 15.3°C (P = 0.005). When the self-drilling pin insertion was decreased considerably from 360 to 60 rpm, the temperature decreased significantly from 151.3 ± 21.6°C to 109.6 ± 14.0°C (P drilling pin temperature increase was not significant. The standard pin had lower peak temperatures than the self-drilling pin for all conditions. Moreover, slowing down the insertion speed and adding irrigation helped mitigate the temperature increase of both pin types during insertion.
Functionally different PIN proteins control auxin flux during bulbil development in Agave tequilana.
Abraham Juárez, María Jazmín; Hernández Cárdenas, Rocío; Santoyo Villa, José Natzul; O'Connor, Devin; Sluis, Aaron; Hake, Sarah; Ordaz-Ortiz, José; Terry, Leon; Simpson, June
2015-07-01
In Agave tequilana, reproductive failure or inadequate flower development stimulates the formation of vegetative bulbils at the bracteoles, ensuring survival in a hostile environment. Little is known about the signals that trigger this probably unique phenomenon in agave species. Here we report that auxin plays a central role in bulbil development and show that the localization of PIN1-related proteins is consistent with altered auxin transport during this process. Analysis of agave transcriptome data led to the identification of the A. tequilana orthologue of PIN1 (denoted AtqPIN1) and a second closely related gene from a distinct clade reported as 'Sister of PIN1' (denoted AtqSoPIN1). Quantitative real-time reverse transcription-PCR (RT-qPCR) analysis showed different patterns of expression for each gene during bulbil formation, and heterologous expression of the A. tequilana PIN1 and SoPIN1 genes in Arabidopsis thaliana confirmed functional differences between these genes. Although no free auxin was detected in induced pedicel samples, changes in the levels of auxin precursors were observed. Taken as a whole, the data support the model that AtqPIN1 and AtqSoPIN1 have co-ordinated but distinct functions in relation to auxin transport during the initial stages of bulbil formation. © The Author 2015. Published by Oxford University Press on behalf of the Society for Experimental Biology.
Study of PIN diode energy traps created by neutrons
International Nuclear Information System (INIS)
Sopko, V; Dammer, J; Sopko, B; Chren, D
2013-01-01
Characterization of radiation defects is still ongoing and finds greater application in the increasing radiation doses on semiconductor detectors in experiments. Studying the changes of silicon PIN diode for high doses of radiation is the fundamental motivation for our measurements. In this article we describe the behavior of the PIN diode and development of the disorder caused by neutrons from a 252Cf and doses up to 8 Gy. The calibration curve for PIN diode shows the effect of disorders as the changes of the voltampere characteristics depending on the dose of neutron irradiation. The measured values for defects are in good agreement with created energy traps.
International Nuclear Information System (INIS)
Hayns, M.R.; Adam, J.
1975-08-01
There is no experimental facilities in which a fuel pin can be irradiated in a fast environment under well defined conditions of over power or flow run down. Consequently most of the infor mation which is being accumulated on the behaviour of fuel pins under severe conditions is obtained from either capsule or loop rigs in thermal reactors. It is the purpose of this paper to highlight the differences between the behaviour of fuel pins irradiated in a thermal flux and a fast flux. A typical set of conditions is taken from an overpower experiment in a thermal flux and the behaviour of the system is analysed using the fuel modelling program FRUMP. A second numerical experiment is then performed in which the same conditions prevail, except that a fast flux is assumed, the criterion for comparison being that the total power input to the system is the same in both cases. From the many possible correlations which result from such an exercise the fuel tempreature has been selected to highlight various important features of the two irradiations. It is demonstrated that the flux depression can cause differences in the pin behaviour, even to altering the order of events in a transient. For example fuel melting will occur at different times and at different positions in the fuel in the two cases. It is concluded that the techniques of fuel modelling, as typified in the program FRUMP can provide a very useful tool indeed for the analysis of such experiments and for guiding the establishment of the appropriate correlations for the extrapolation to the fast flux case. (author)
International Nuclear Information System (INIS)
Rodriguez-Rodriguez, G; Hierro-Rodriguez, A; Perez-Junquera, A; Montenegro, N; Alameda, J M; Velez, M; Menendez, J L; Ravelosona, D
2010-01-01
The interplay between collective pinning on intrinsic structural defects and artificial pinning at a patterned hole is studied in magnetic multilayers with perpendicular anisotropy. The pinning strength of a patterned hole is measured through its efficiency to stop domain wall (DW) propagation into a consecutive unpatterned nanowire section (using antisymmetric magnetoresistance to detect the direction of DW propagation) whereas collective pinning is characterized by the field dependence of DW velocity. Close to room temperature, collective pinning becomes weaker than artificial pinning so that pinning at the hole compensates nucleation-pad geometry, blocking DW propagation across the nanowire.
Testing program PIN on experiments reported in EPRI-NP-369
International Nuclear Information System (INIS)
Kunt, J.; Pazdera, F.
1980-03-01
The testing is described of the applicability of program PIN for the thermomechanical simulation of PWR fuel elements. Program PIN is a modified program GAPCON-THERMAL-2. Four modifications are presented mostly affecting the results, viz., the fuel restructuring model, the fuel densification model, the gaseous fission product release model, and the fuel cladding creep model. The results show that the initial data for simulating fuel element behaviour in accident situations are determined using program PIN with accuracy comparable to that using other programs. (J.P.)
Electric arc apparatus for severing split-pin assemblies of guide tubes of nuclear reactors
International Nuclear Information System (INIS)
Burns, D.C.; Kauric, C.E.; Persang, J.C.
1987-01-01
This patent describes an apparatus for use in the replacement of an old split-pin assembly of a guide tube of a nuclear reactor by a new split-pin assembly, the old split-pin assembly including an old split pin and an old nut securing the old split pin to the guide tube, the old split-pin assembly and the guide tube being radioactive. The apparatus includes a metal disintegration machining tool, the tool having an electrode, means for mounting the tool submerged in a pool of water in engagement with the guide tube and with the old split-pin assembly secured to the guide tube, the tool being so mounted with the electrode in position to coact electrically with the last-named old split-pin assembly but not with the guide tube, and means, connected to the tool, for firing a disintegrating arc between the electrode and the assembly to disintegrate the assembly into readily removable fragments
Risk analysis in the chemical industry; Analisis de riesgos en la industria quimica
Energy Technology Data Exchange (ETDEWEB)
Rea Soto, Rogelio; Sandoval Valenzuela, Salvador [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico)
2000-07-01
The Instituto de Investigaciones Electricas has a group of risk analysis (GAR), specialized in the most advanced methodologies to apply them in diverse industries of the productive sector, such as the nuclear, the oil and the chemical industries. In this work the integrated methodology that the GAR uses to make risk analysis in the chemical and oil industries is described. These analyses have as an objective to make a meticulous evaluation of the system design, the operation practices, the maintenance and inspection policies and the emergency plans. [Spanish] El Instituto de Investigaciones Electricas cuenta con un grupo de analisis de riesgo (GAR), especializado en las metodologias mas avanzadas para aplicarlas en diversas industrias del sector productivo, como lo son la nuclear, la petrolera y la quimica. En este trabajo se describe la metodologia integrada que el GAR utiliza para realizar analisis de riesgos en las industrias quimica y petrolera. Estos analisis tienen como objetivo realizar una minuciosa evaluacion del diseno del sistema, las practicas de operacion, las politicas de mantenimiento e inspeccion y los planes de emergencia.
Analisis Reduksi Intensitas Cahaya Pada Smartphones’ Screen Protector Dan Dampaknya Pada Mata
Directory of Open Access Journals (Sweden)
Bhekti Kumorowati
2017-04-01
Full Text Available Analisis reduksi intensitas cahaya yang melewati screen protector dan identifikasi kemampuan screen protector sebagai pelindung mata dilakukan dengan mengukur reduksi intensitas cahaya menggunakan luxmeter, kemudian menetapkan fokus bahasan yang mencakup kemampuan cahaya menembus screen protector dan analisis fisis screen protector sebagai pelindung mata. Peran sebagai pelindung mata dikaji melalui pendekatan peristiwa polarisasi yaitu proses terserapnya sebagian arah getar cahaya. Dihasilkan sebagian arah getar cahaya layar smartphone sebelum masuk ke mata akan terserap oleh screen protector sehingga dapat memperlambat terjadinya degenerasi makula. Rekomendasi pemilihan screen protector bergantung pada besarnya koefisien atenuasi (koefisien penyerapan yang dimiliki masing-masing screen protector. Koefisien atenuasi terbesar dimiliki oleh screen protector jenis anti spy.
Development of a semiconductor neutron dosimeter with a PIN diode
International Nuclear Information System (INIS)
Kim, Seungho; Lee, Namho; Cho, Jaiwan; Youk, Geunuck
2004-01-01
When a Si PIN diode is exposed to fast neutrons, it produces displacement in Si lattice structure of the diode. Defects induced from structural dislocation become effective recombination centers for carriers which pass through the base of a PIN diode. Hence, increasing the resistivity of the diode decreases the current for the applied forward voltage. This paper involves the development of a neutron sensor based on the phenomena of the displacement effect damaged by neutron exposure. The neutron effect on the semiconductor was analyzed, and multi PIN diode arrays with various intrinsic layer (I layer) thicknesses and cross sections were fabricated. Under irradiation tests with a neutron beam, the manufactured diodes have good characteristics of linearity in a neutron irradiation experiment and give results that the increase of thickness of I layer and the decrease of the cross-section of the PIN diodes improve the sensitivity. Newly developed PIN diodes with a thicker I layer and various cross sections were retested and showed the best neutron sensitivity in the condition that the I layer thickness was similar to the length of a side of the cross-section. On the basis of two test results, final PIN diodes with a rectangular shape were manufactured and the characteristics for neutron detectors were analyzed through the neutron beam test using the on-line electronic dosimetry system. The developed PIN diode shows a good linearity to absorbed dose in the range of 0 to 1,000cGy (Tissue) and its neutron sensitivity is 13 mV/cGy at a constant current of 5 mA, that is three higher than that of similar commercially developed neutron detectors. Moreover the device shows less dependency on the orientation of the neutron beam and a considerable stability in an annealing test for a long period. (author)
Turban pin aspiration: new fashion, new syndrome.
Ilan, Ophir; Eliashar, Ron; Hirshoren, Nir; Hamdan, Kasem; Gross, Menachem
2012-04-01
Turban pin aspiration syndrome is a new clinical entity afflicting young Islamic girls wearing a turban.The goal of this study was to present our experience in diagnosis and treatment of this new entity, define its clinical and epidemiologic features, and shed a new light on the role of fashion in the increased incidence. A retrospective study in a tertiary university hospital. Review of clinical parameters and epidemiologic features of 26 patients diagnosed with turban pin aspiration syndrome admitted to the Hadassah-Hebrew University Hospitals in Jerusalem from 1990 to 2010. All patients were Muslim females with an average age of 16 years. In all cases, the history was positive for accidental aspiration. Most of the pins were located in the trachea (42%). In 20 cases, the pins were extracted by rigid bronchoscopy without major complications. Fluoroscopy-assisted rigid bronchoscopy was used successfully in three cases. In one case, the object was self-ejected by coughing before the bronchoscopy, and two patients were referred to the chest unit for thoracotomy. Clinicians should be aware of this distinct form of foreign body aspiration, its method of diagnosis, and extraction techniques. A cultural investigation showed a difference in the turban-fastening technique of young girls as compared with their mothers. Removal by rigid bronchoscopy is a safe method with a high success rate and should be considered as the preferred extraction method of choice. Copyright © 2012 The American Laryngological, Rhinological, and Otological Society, Inc.
Actions undertaken in order to solve the tube guide pins cracking
International Nuclear Information System (INIS)
Benhamou, C.; Briois, J.P.; Tuncer, T.; Drean, H.
1985-01-01
Short-term actions have been developed after the discovery of defects on the guide tube pins (upper internal rector components) of 21 units in France. The impact analysis of a pin failure on the safety by Framatome show that short-term consequences are not very important. Improvements in regard with the design and the stress corrosion resistance of the material, which can be applied to the pins, have been defined. Framatome and EDF developed tools and the mastery of replacement operations what led to limit considerably the unavailability of units; 17 units have been treated for two years and half; the four last ones will be treated in 1985. Parallel studies allow to estimate the available marge of in-service behavior of the replacement pins; this marge is increased in units which are built now by means of new developments concerning the design and the mounting conditions. A method and tools utilizing ultrasonic waves have been developed for on-site inspection of the pins [fr
Intrinsic flux pinning mechanisms in different thickness MgB2 films
Directory of Open Access Journals (Sweden)
C. Yang
2017-03-01
Full Text Available MgB2 films in four thickness (60 nm, 200nm, 600nm and 1μm have been fabricated by hybrid physical–chemical vapor deposition technique (HPCVD. By measuring the magnetization hysteresis loops and the resistivity, we have obtained the transport and magnetic properties of the four films. After that, the pinning mechanisms in them were discussed. Comparing the pinning behaviors in these ultrathin films, thin films and thick films, it was found that there exist different pinning types in MgB2 films of different thickness. In combination with the study of the surface morphology, cross-section and XRD results, we concluded that MgB2 films had different growth modes in different growth stages. For thin films, films grew along c axis, and grain boundaries acted as surface pinning. While for thick films, films grew along c axis at first, and then changed to a-b axis growth. As a result, the a-b axis grains acted as strong volume pinning.
Thermal-Hydraulic Simulations of Single Pin and Assembly Sector for IVG- 1M Reactor
Energy Technology Data Exchange (ETDEWEB)
Kraus, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Garner, P. [Argonne National Lab. (ANL), Argonne, IL (United States); Hanan, N. [Argonne National Lab. (ANL), Argonne, IL (United States)
2015-01-15
Thermal-hydraulic simulations have been performed using computational fluid dynamics (CFD) for the highly-enriched uranium (HEU) design of the IVG.1M reactor at the Institute of Atomic Energy (IAE) at the National Nuclear Center (NNC) in the Republic of Kazakhstan. Steady-state simulations were performed for both types of fuel assembly (FA), i.e. the FA in rows 1 & 2 and the FA in row 3, as well as for single pins in those FA (600 mm and 800 mm pins). Both single pin calculations and bundle sectors have been simulated for the most conservative operating conditions corresponding to the 10 MW output power, which corresponds to a pin unit cell Reynolds number of only about 7500. Simulations were performed using the commercial code STAR-CCM+ for the actual twisted pin geometry as well as a straight-pin approximation. Various Reynolds-Averaged Navier-Stokes (RANS) turbulence models gave different results, and so some validation runs with a higher-fidelity Large Eddy Simulation (LES) code were performed given the lack of experimental data. These singled out the Realizable Two-Layer k-ε as the most accurate turbulence model for estimating surface temperature. Single-pin results for the twisted case, based on the average flow rate per pin and peak pin power, were conservative for peak clad surface temperature compared to the bundle results. Also the straight-pin calculations were conservative as compared to the twisted pin simulations, as expected, but the single-pin straight case was not always conservative with regard to the straight-pin bundle. This was due to the straight-pin temperature distribution being strongly influenced by the pin orientation, particularly near the outer boundary. The straight-pin case also predicted the peak temperature to be in a different location than the twisted-pin case. This is a limitation of the straight-pin approach. The peak temperature pin was in a different location from the peak power pin in every case simulated, and occurred at an
Cluster synchronization for directed community networks via pinning partial schemes
International Nuclear Information System (INIS)
Hu Cheng; Jiang Haijun
2012-01-01
Highlights: ► Cluster synchronization for directed community networks is proposed by pinning partial schemes. ► Each community is considered as a whole. ► Several novel pinning criteria are derived based on the information of communities. ► A numerical example with simulation is provided. - Abstract: In this paper, we focus on driving a class of directed networks to achieve cluster synchronization by pinning schemes. The desired cluster synchronization states are no longer decoupled orbits but a set of un-decoupled trajectories. Each community is considered as a whole and the synchronization criteria are derived based on the information of communities. Several pinning schemes including feedback control and adaptive strategy are proposed to select controlled communities by analyzing the information of each community such as indegrees and outdegrees. In all, this paper answers several challenging problems in pinning control of directed community networks: (1) What communities should be chosen as controlled candidates? (2) How many communities are needed to be controlled? (3) How large should the control gains be used in a given community network to achieve cluster synchronization? Finally, an example with numerical simulations is given to demonstrate the effectiveness of the theoretical results.
Irradiation of TZM: Uranium dioxide fuel pin at 1700 K
Mcdonald, G. E.
1973-01-01
A fuel pin clad with TZM and containing solid pellets of uranium dioxide was fission heated in a static helium-cooled capsule at a maximum surface temperature of 1700 K for approximately 1000 hr and to a total burnup of 2.0 percent of the uranium-235. The results of the postirradiation examination indicated: (1) A transverse, intergranular failure of the fuel pin occurred when the fuel pin reached 2.0-percent burnup. This corresponds to 1330 kW-hr/cu cm, where the volume is the sum of the fuel, clad, and void volumes in the fuel region. (2) The maximum swelling of the fuel pin was less than 1.5 percent on the fuel-pin diameter. (3) There was no visible interaction between the TZM clad and the UO2. (4) Irradiation at 1700 K produced a course-grained structure, with an average grain diameter of 0.02 centimeter and with some of the grains extending one-half of the thickness of the clad. (5) Below approximately 1500 K, the irradiation of the clad produced a moderately fine-grained structure, with an average grain diameter of 0.004 centimeter.
Vortex pinning in artificially layered Ba(Fe,Co)2As2 film
Oh, M. J.; Lee, Jongmin; Seo, Sehun; Yoon, Sejun; Seo, M. S.; Park, S. Y.; Kim, Ho-Sup; Ha, Dong-Woo; Lee, Sanghan; Jo, Youn Jung
2018-06-01
Static high critical current densities (Jc) > 1 MA/cm2 with magnetic field parallel or perpendicular to c-axis were realized in Co-doped/undoped multilayerd BaFe2As2 films. We made a current bridge by FIB to allow precise measurements, and confirmed that the boundary quality using FIB was considerably better than the quality achieved using a laser. The presence of a high in-plane Jc suggested the existence of c-axis correlated vortex pinning centers. To clarify the relationship between the Jc performance and superstructures, we investigated the magnetic flux pinning mechanism using scaling theory of the volume pinning force Fp(H). The Jc(H) curves, Fp/Fp,max vs. h = H/Hirr curves, and parameters p and q depended on the characteristics of the flux pinning mechanism. It was found that the dominant pinning mechanism of Co-doped/undoped multilayerd BaFe2As2 films was Δl-pinning and the inserted undoped BaFe2As2 layers remained non-superconducting. The dominant pin geometry varied when the magnetic field direction changed. It was concluded that the artificially layered BaFe2As2 film is a 3-D superconductor due to its long correlation length compared to the thickness of the non-superconducting layer.
Joining of aluminum sheet and glass fiber reinforced polymer using extruded pins
Conte, Romina; Buhl, Johannes; Ambrogio, Giuseppina; Bambach, Markus
2018-05-01
The present contribution proposes a new approach for joining sheet metal and fiber reinforced composites. The joining process draws upon a Friction Stir Forming (FSF) process, which is performed on the metal sheet to produce slender pins. These pins are used to pierce through the composite. Joining is complete by forming a locking head out of the part if the pin sticks out of the composite. Pins of different diameters and lengths were produced from EN AW-1050 material, which were joined to glass fiber reinforced polyamide-6. The strength of the joint has been experimentally tested in order to understand the effect of the process temperature on the pins strength and therefore on the joining. The results demonstrate the feasibility of this new technique, which uses no excess material.
Analisis Termal High Pressure Feedwater Heater di PLTU PT. XYZ
Directory of Open Access Journals (Sweden)
Maria Ulfa Damayanti
2017-01-01
Full Text Available Abstrak- PT. XYZ mengoperasikan tiga unit Pembangkit Listrik Tenaga Uap (PLTU unit 3, 7 dan 8 berkapasitas 2.030 MegaWatt. Pada PLTU Paiton unit 7 dan 8 terdapat delapan buah feedwater heater yaitu empat buah Low Pressure Water Heater (LPWH, tiga buah High Pressure Water Heater (HPWH, dan sebuah dearator. Pada PLTU Paiton unit 7 dan 8 terdapat kerusakan pada HPWH 6 yang menyebabkan penurunan efisiensi dari siklus secara keseluruhan. Penurunan efisiensi dapat terjadi karena temperatur feedwater sebelum masuk ke boiler terlalu rendah, sehingga kalor yang dibutuhkan oleh boiler untuk memanaskan feedwater meningkat. Oleh karena itu konsumsi batubara akan meningkat dan menyebabkan terjadi kenaikan biaya operasional harian dalam sistem pembangkit. Dari data Divisi Produksi PT. XYZ Unit 7 dan 8 diperoleh spesifikasi HPWH 6, 7, dan 8 dan propertis fluida dalam HPWH 6, 7, dan 8. Data tersebut digunakan sebagai dasar analisis termal yang meliputi performa masing-masing HPH. Tahap selanjutnya dalam analisis termal adalah memvariasikan beban 25%, 50%, 75%, 100%, dan 105%. Tahap terakhir analisis adalah menghitung performa dengan variasi sumbatan (plug 5%, 10%, 15%, dan 20% sesuai dengan variasi beban. Hasil yang didapatkan dari penelitian tugas akhir ini adalah nilai effectiveness tertinggi tercapai pada pembebanan 100% serta menghasilkan pressure drop tertinggi pada pembebanan 105%, nilai effectiveness terbesar serta nilai pressure drop terkecil terjadi pada zona Condensing, serta sumbatan (plugging pada HPH akan menyebabkan penurunan nilai effectiveness dan kenaikan pressure drop sisi tube.
Thermal-hydraulics and neutronics studies on the FP7 CP-ESFR oxide and carbide cores
Energy Technology Data Exchange (ETDEWEB)
Ammirabile, L.; Tsige-Tamirat, H. [European Commission, JRC, Inst. for Energy, Petten (Netherlands)
2011-07-01
In the framework of the the Collaborative Project on European Sodium Fast Reactor (CP-ESFR) two core designs that are currently being proposed for the 3600 MWth sodium-cooled reactor concept: one is based on oxide fuel and the other on carbide fuel. Using the European Safety Assessment Platform (ESAP), JRC-IE has conducted static calculation on neutronics (incl. reactivity coefficients) and thermal-hydraulic characteristics for both oxide and carbide reference cores. The quantities evaluated include: keff, coolant heat-up, void, and Doppler reactivity coefficients, axial and radial expansion reactivity coefficients, pin-by-pin calculated power profiles, average and peak channel temperatures. This paper presents the ESAP models applied in the study together with the relevant results for the oxide and carbide core. (author)
Thermal-hydraulics and neutronics studies on the FP7 CP-ESFR oxide and carbide cores
International Nuclear Information System (INIS)
Ammirabile, L.; Tsige-Tamirat, H.
2011-01-01
In the framework of the the Collaborative Project on European Sodium Fast Reactor (CP-ESFR) two core designs that are currently being proposed for the 3600 MWth sodium-cooled reactor concept: one is based on oxide fuel and the other on carbide fuel. Using the European Safety Assessment Platform (ESAP), JRC-IE has conducted static calculation on neutronics (incl. reactivity coefficients) and thermal-hydraulic characteristics for both oxide and carbide reference cores. The quantities evaluated include: keff, coolant heat-up, void, and Doppler reactivity coefficients, axial and radial expansion reactivity coefficients, pin-by-pin calculated power profiles, average and peak channel temperatures. This paper presents the ESAP models applied in the study together with the relevant results for the oxide and carbide core. (author)
Pin Tool Geometry Effects in Friction Stir Welding
Querin, J. A.; Rubisoff, H. A.; Schneider, J. A.
2009-01-01
In friction stir welding (FSW) there is significant evidence that material can take one of two different flow paths when being displaced from its original position in front of the pin tool to its final position in the wake of the weld. The geometry of the pin tool, along with the process parameters, plays an important role in dictating the path that the material takes. Each flow path will impart a different thermomechanical history on the material, consequently altering the material microstructure and subsequent weld properties. The intention of this research is to isolate the effect that different pin tool attributes have on the flow paths imparted on the FSWed material. Based on published weld tool geometries, a variety of weld tools were fabricated and used to join AA2219. Results from the tensile properties and microstructural characterization will be presented.
Volume pinning force and upper critical field of irradiated Nb3Sn
International Nuclear Information System (INIS)
Maier, P.; Seibt, E.
1981-01-01
Irradiation by neutrons and ions in A15 superconductors (Nb 3 Sn, V 3 Ga) exerts a stronger influence on the pinning behavior than in nonordered alloys (NbTi). In this work it is shown for deuteron irradiated Nb 3 /Sn wires prepared by the bronze process that the dose curve of the volume pinning force P/sub V/ can be conveniently described by a sum of two terms, due to the grain boundary pinning and to the radiation pinning, respectively. After deduction of the contribution by the radiation-induced pinning centers, good agreement is obtained between the measured P/sub V/ values and those calculated using the upper critical field B/sub c/2 and the transition temperature T/sub c/ on the basis of the irradiation fluence. The use of a theoretical relationship between B/sub c/2 and T/sub c/ is supported by measured values. Application to multifilamentary superconductors with high current carrying capabilities simplifies the calculation of P/sub V/, since the radiation induced volume pinning force can be neglected
Generalized pin factor methodology for LWR reload cores with discrete burnable absorbers
International Nuclear Information System (INIS)
Hah, C.J.; Hideki Matsumoto; Toshikazu Ida; Lee, C.; Chao, Y.A.
2005-01-01
Discrete burnable absorbers are used to suppress excess reactivity as well as peak pin power in an assembly. After the burn-out of absorption material, discrete burnable absorbers are usually removed from assembly guide tubes for the next cycle. For that case, the pin factors with discrete burnable absorbers cannot be used since the assembly configuration is physically changed. The pin factors without discrete burnable absorbers also have noticeable deviation from the actual case because they do not take into account the history effect due to the residence of discrete burnable absorbers for the previous cycle. In this paper, the generalized pin factor (GPF) method is developed to accurately predict pin powers by considering the history effect. The method uses a second-order polynomial function to approximate the history effect which builds up during the residence of burnable absorber material and employs a linear approximation to simulate the decay of the history effect after discrete burnable absorbers are removed. The verification results from Westinghouse Vantage- 5H assemblies with WABAs showed that pin power errors were significantly reduced by using the GPF. (authors)
Development of wire wrapping technology for FBR fuel pin
International Nuclear Information System (INIS)
Nogami, Tetsuya; Seki, Nobuo; Sawayama, Takeo; Ishibashi, Takashi
1991-01-01
For the FBR fuel assembly, the spacer wire is adopted to maintain the space between fuel pins. The developments have been carried out to achieve automatically wire wrapping with high precision. Based on the fundamental technology developed through the mock-up test operation, Joyo 'MK-I', fuel pin fabrication was started using partially mechanized wire wrapping machine in 1973. In 1978, an automated wire wrapping machine for Joyo 'MK-II' was developed by the adoption of some improvements for the wire inserting system to end plug hole and the precision of wire pitch. On the bases of these experiences, fully automated wire wrapping machine for 'Monju' fuel pin was installed at Plutonium Fuel Production Facility (PFPF) in 1987. (author)
The pin pixel detector--neutron imaging
Bateman, J E; Derbyshire, G E; Duxbury, D M; Marsh, A S; Rhodes, N J; Schooneveld, E M; Simmons, J E; Stephenson, R
2002-01-01
The development and testing of a neutron gas pixel detector intended for application in neutron diffraction studies is reported. Using standard electrical connector pins as point anodes, the detector is based on a commercial 100 pin connector block. A prototype detector of aperture 25.4 mmx25.4 mm has been fabricated, giving a pixel size of 2.54 mm which matches well to the spatial resolution typically required in a neutron diffractometer. A 2-Dimensional resistive divide readout system has been adapted to permit the imaging properties of the detector to be explored in advance of true pixel readout electronics. The timing properties of the device match well to the requirements of the ISIS-pulsed neutron source.
Tips Under the Skin: A Simple Modification of Extension Block Pinning for Mallet Fractures.
Shin, Seung-Han; Lee, Yong-Suk; Kang, Jin-Woo; Kang, Wonwoo; Chung, Yang-Guk
2018-03-01
Pins exposed out of the skin after surgery for mallet fractures keep patients from washing their hands. The authors buried the tips of all pins under the skin while performing extension block pinning for 14 patients with mallet fractures. The patients were allowed to wash their hands 4 to 5 days postoperatively, without any dressing or splinting. The pins were removed at a mean of 8 weeks postoperatively. Solid union was achieved in all 14 fractures. No pull-out or subsidence of the pin was observed. No patient developed infection or other pin-related complications. Mean extension lag at final follow-up was 4°. [Orthopedics. 2018; 41(2):e299-e302.]. Copyright 2018, SLACK Incorporated.
Carbon deposition on 20/25/Nb steel using an electrically heated AGR fuel pin
International Nuclear Information System (INIS)
Blanchard, A.; Campion, P.
1980-01-01
The radiolysis of carbon dioxide in gas-cooled reactors leads to the production of active species capable of reacting with the graphite moderator to form carbon monoxide with a resultant gradual loss of moderator. In the early days of gas-cooled reactor design, the intention was to allow the carbon monoxide concentration to increase and use this reaction product to inhibit the initial radiolysis of the carbon dioxide. Exploratory irradiation experiments using 4 to 7% carbon monoxide revealed that low density deposits ranging in colour from light grey through brown to black were found in the temperature range 470 to 600 K. In view of the fact that this type of deposition could adversely affect heat transfer processes in both fuel channels and heat exchangers, together with the fact that carbon monoxide was not sufficiently powerful as a graphite oxidation inhibitor, methane was selected as the primary inhibitor for the AGR series of power stations. This paper describes some carbon deposition experiments using an electrically heated 'dummy fuel element' linked to a recirculating carbon dioxide irradiation loop in which carbon monoxide concentration, methane concentration, fuel pin temperature and the chemical nature of the fuel pin surface were varied. (author)
Performance measurements of hybrid PIN diode arrays
International Nuclear Information System (INIS)
Jernigan, J.G.; Arens, J.F.; Collins, T.; Herring, J.; Shapiro, S.L.; Wilburn, C.D.
1990-05-01
We report on the successful effort to develop hybrid PIN diode arrays and to demonstrate their potential as components of vertex detectors. Hybrid pixel arrays have been fabricated by the Hughes Aircraft Co. by bump bonding readout chips developed by Hughes to an array of PIN diodes manufactured by Micron Semiconductor Inc. These hybrid pixel arrays were constructed in two configurations. One array format having 10 x 64 pixels, each 120 μm square, and the other format having 256 x 256 pixels, each 30 μm square. In both cases, the thickness of the PIN diode layer is 300 μm. Measurements of detector performance show that excellent position resolution can be achieved by interpolation. By determining the centroid of the charge cloud which spreads charge into a number of neighboring pixels, a spatial resolution of a few microns has been attained. The noise has been measured to be about 300 electrons (rms) at room temperature, as expected from KTC and dark current considerations, yielding a signal-to-noise ratio of about 100 for minimum ionizing particles. 4 refs., 13 figs
Analisis Kinerja Local Area Network Menggunakan Router.
Hutahaean, Yosua
2012-01-01
Perangkat internetworking menawarkan komunikasi di antara segmen Local Area Network (LAN). Ada empat tipe utama perangkat internetworking ini: repeater, bridge, router, dan gateway. Perangkat ini dibedakan atas dasar system lapisan Open System Interconnection (OSI) yang digunakan, berfungsi sebagai media komunikasi dari LAN ke LAN. Pada Tugas Akhir ini penulis tertarik untuk membahas analisis kinerja Local Area Network (LAN) menggunakan Router yang menggunakan sistem antrian M/M/1 dimana j...
International Nuclear Information System (INIS)
Zhao-Bing, Liu; Hua-Guang, Zhang; Qiu-Ye, Sun
2010-01-01
This paper considers the global stability of controlling an uncertain complex network to a homogeneous trajectory of the uncoupled system by a local pinning control strategy. Several sufficient conditions are derived to guarantee the network synchronisation by investigating the relationship among pinning synchronisation, network topology, and coupling strength. Also, some fundamental and yet challenging problems in the pinning control of complex networks are discussed: (1) what nodes should be selected as pinned candidates? (2) How many nodes are needed to be pinned for a fixed coupling strength? Furthermore, an adaptive pinning control scheme is developed. In order to achieve synchronisation of an uncertain complex network, the adaptive tuning strategy of either the coupling strength or the control gain is utilised. As an illustrative example, a network with the Lorenz system as node self-dynamics is simulated to verify the efficacy of theoretical results. (general)
Correlation Between Pin Misalignment and Crack Length in THT Solder Joints
Directory of Open Access Journals (Sweden)
Molnar A.
2017-06-01
Full Text Available In this manuscript, correlations were searched for between pin misalignments relative to PCB bores and crack propagation after cyclic thermal shock tests in THT solder joints produced from lead-free solder alloys. In total, 7 compositions were examined including SAC solders with varying Ag, Cu and Ni contents. The crack propagation was initiated by cyclic thermal shock tests with 40°C / +125°C temperature profiles. Pin misalignments relative to the bores were characterized with three attributes obtained from one section of the examined solder joints. Cracks typically originated at the solder/pin or solder/bore interfaces and propagated within the solder. It was shown that pin misalignments did not have an effect on crack propagation, thus, the solder joints’ lifetime.
Reliability of fast reactor mixed-oxide fuel during operational transients
International Nuclear Information System (INIS)
Boltax, A.; Neimark, L.A.; Tsai, Hanchung; Katsuragawa, M.; Shikakura, S.
1991-07-01
Results are presented from the cooperative DOE and PNC Phase 1 and 2 operational transient testing programs conducted in the EBR-2 reactor. The program includes second (D9 and PNC 316 cladding) and third (FSM, AST and ODS cladding) generation mixed-oxide fuel pins. The irradiation tests include duty cycle operation and extended overpower tests. the results demonstrate the capability of second generation fuel pins to survive a wide range of duty cycle and extended overpower events. 15 refs., 9 figs., 4 tabs
A polygonal nodal SP3 method for whole core Pin-by-Pin neutronics calculation
Energy Technology Data Exchange (ETDEWEB)
Li, Yunzhao; Wu, Hongchun; Cao, Liangzhi, E-mail: xjtulyz@gmail.com, E-mail: hongchun@mail.xjtu.edu.cn, E-mail: caolz@mail.xjtu.edu.cn [School of Nuclear Science and Technology, Xi' an Jiaotong University, Shaanxi (China)
2011-07-01
In this polygonal nodal-SP3 method, neutron transport equation is transformed by employing an isotropic SP3 method into two coupled equations that are both in the same mathematic form with the diffusion equation, and then a polygonal nodal method is proposed to solve the two coupled equations. In the polygonal nodal method, adjacent nodes are coupled through partial currents, and a nodal response matrix between incoming and outgoing currents is obtained by expanding detailed nodal flux distribution into a sum of exponential functions. This method avoids the transverse integral technique, which is widely used in regular nodal method and can not be used in triangular geometry because of the mathematical singularity. It is demonstrated by the numerical results of the test problems that the k{sub eff} and power distribution agree well with other codes, the triangular nodal-SP3 method appears faster, and that whole core pin-by-pin transport calculation with fine meshes is feasible after parallelization and acceleration. (author)
Sodium Loop Safety Facility W-2 experiment fuel pin rupture detection system. [LMFBR
Energy Technology Data Exchange (ETDEWEB)
Hoffman, M.A.; Kirchner, T.L.; Meyers, S.C.
1980-05-01
The objective of the Sodium Loop Safety Facility (SLSF) W-2 experiment is to characterize the combined effects of a preconditioned full-length fuel column and slow transient overpower (TOP) conditions on breeder reactor (BR) fuel pin cladding failures. The W-2 experiment will meet this objective by providing data in two technological areas: (1) time and location of cladding failure, and (2) early post-failure test fuel behavior. The test involves a seven pin, prototypic full-length fast test reactor (FTR) fuel pin bundle which will be subjected to a simulated unprotected 5 cents/s reactivity transient overpower event. The outer six pins will provide the necessary prototypic thermal-hydraulic environment for the center pin.
Directory of Open Access Journals (Sweden)
Fengming Wang
2012-12-01
Full Text Available The flow and heat transfer characteristics inside a rectangular channel embedded with pin fins were numerically and experimentally investigated. Several differently shaped pin fins (i.e., circular, elliptical, and drop-shaped with the same cross-sectional areas were compared in a staggered arrangement. The Reynolds number based on the obstructed section hydraulic diameter (defined as the ratio of the total wetted surface area to the open duct volume available for flow was varied from 4800 to 8200. The more streamlined drop-shaped pin fins were better at delaying or suppressing separation of the flow passing through them, which decreased the aerodynamic penalty compared to circular pin fins. The heat transfer enhancement of the drop-shaped pin fins was less than that of the circular pin fins. In terms of specific performance parameters, drop-shaped pin fins are a promising alternative configuration to circular pin fins.
Use of a modified transfixation pin cast for treatment of comminuted phalangeal fractures in horses.
Rossignol, Fabrice; Vitte, Amélie; Boening, Josef
2014-01-01
To (1) report a modified transfixation pin cast technique, using dorsal recumbency for fracture reduction, distal positioning of the pins in the epiphysis and distal metaphysis, and a hybrid cast, combining plaster of Paris (POP) and fiberglass casting, and (2) report outcome in 11 adult horses. Case series. Adult horses (n = 11) with comminuted phalangeal fractures. Horses were anesthetized and positioned in dorsal recumbency. The phalangeal fracture was reduced by limb traction using a cable attached to the hoof. Screw fixation in lag fashion of fracture fragments was performed when possible. Transfixation casting was performed using two 6.3 mm positive profile centrally threaded pins with the 1st pin placed in the epiphysis of the metacarpus/tarsus at the center of, or slightly proximal to, the condylar fossa and the 2nd one 3-4 cm proximal. A hybrid cast was applied. Forelimbs were involved in 9 horses and the hind limb in 2. Pins were maintained for a minimum of 6 weeks. No pin loosening was observed at the time of removal (6-8 weeks). A pony fractured the distal aspect of the metacarpus at the proximal pin. Nine horses survived (82%); none of the horses developed septic arthritis despite the distal location of the distal pin, close to the fetlock joint. This modified transfixation pin casting technique was associated with good pin longevity and could reduce the risk of secondary pin hole fractures and pin loosening. © Copyright 2013 by The American College of Veterinary Surgeons.
High energy x-ray radiography and computed tomography of bridge pins
International Nuclear Information System (INIS)
Green, R E; Logan, C M; Martz, H E; Updike, E; Waters, A M
1999-01-01
Bridge pins were used in the hanger assemblies for some multi-span steel bridges built prior to the 1980's, and are sometimes considered fracture critical elements of a bridge. During a test on a bridge conducted by the Federal Highway Administration (FHWA), ultrasonic field inspection results indicated that at least two pins contained cracks. Several pins were removed and selected for further examination. This provided an excellent opportunity to learn more about these pins and the application of x-ray systems at Lawrence Livermore National Laboratory (LLNL), as well as to learn more about the application of different detectors recently obtained by LLNL. Digital radiographs and computed tomography (CT) were used to characterize the bridge pins, using a LINAC x-ray source with a 9-MV bremsstrahlung spectrum. We will describe the performance of two different digital radiographic detectors. One is a detector system frequently used at LLNL consisting of a scintillator glass optically coupled to a CCD camera. The other detector is a new amorphous silicon detector recently acquired by LLNL
International Nuclear Information System (INIS)
Hartley, Kenneth; Moulding, T.L.J.; Rostron, Norman.
1979-01-01
Fuel pin for use in fast breeder nuclear reactors containing fissile and fertile areas of which the fissile and fertile materials do not mix. The fissile material takes the shape of large and small diameter microspheres (the small diameter microspheres can pass through the interstices between the large microspheres). The barrier layers being composed of microspheres with a diameter situated between those of the large and small microspheres ensure that the materials do not mix [fr
Influence of oxygen-metal ratio on mixed-oxide fuel performance
International Nuclear Information System (INIS)
Lawrence, L.A.; Leggett, R.D.
1979-04-01
The fuel oxygen-to-metal ratio (O/M) is recognized as an important consideration for performance of uranium--plutonium oxide fuels. An overview of the effects of differing O/M's on the irradiation performance of reference design mixed-oxide fuel in the areas of chemical and mechanical behavior, thermal performance, and fission gas behavior is presented. The pellet fuel has a nominal composition of 75 wt% UO 2 + 25 wt% PuO 2 at a pellet density of approx. 90% TD. for nominal conditions this results in a smeared density of approx. 85%. The cladding in all cases is 20% CW type 316 stainless steel with an outer diameter of 5.84 to 6.35 mm. O/M has been found to significantly influence fuel pin chemistry, mainly FCCI and fission product and fuel migration. It has little effect on thermal performance and overall mechanical behavior or fission gas release. The effects of O/M (ranging from 1.938 to 1.984) in the areas of fuel pin chemistry, to date, have not resulted in any reduction in fuel pin performance capability to goal burnups of approx. 8 atom% or more
A novel reconfigurable electromagnetically induced transparency based on S-PINs
Xue, Feng; Liu, Shao-Bin; Zhang, Hai-Feng; Wen, Yong-Diao; Kong, Xiang-Kun; Li, Hai-Ming
2018-02-01
In this paper, a tunable electromagnetically induced transparency (EIT) based on S-PINs is theoretically analyzed. Unit cell of the structure consists of a cutwire (CW), split ring resonator (SRR), and solid state plasma (SS plasma) patches which are composed of S-PIN array. The destructive interference between the CW and SRR results in a narrowband transparency window accompanied with strong phase dispersion. The proposed design can obtain a tunable EIT with different frequencies range from 12.8 GHz to 16.5 GHz in a simple method by switching these S-PINs on or off selectively. The related parameters of the S-PIN such as the size, carrier concentration, and volt-ampere characteristics have been studied theoretically. The interaction and coupling between two resonators are investigated in detail by the analysis of the current distribution and E-field strength as well. The research results provide an effective way to realize reconfigurable compact slow-light devices.
Analisis Penerimaan PAD Pada Dinas Perikanan dan Peternakan Kabupaten Tebo
Directory of Open Access Journals (Sweden)
Eko Purnarianto
2016-06-01
Full Text Available Abstract. This study aims to analyze potential, efficiency, effectivity and contribution of PAD admission at Department of Fishery and Animal Husbandry in Tebo Regencyincluding the strategy establishment to increase its revenue.The analysis used is a potential formula, efficiency ratio, effectivity ratio, contributions ratio and SWOT analysis.The results shows that the potential revenue of retribution slaughterhouse (RPH, the potential sales of livestock, and potential sales fishery product are beyond the current target. The efficiency level of retribution slaughterhouse (RPH and sales of fishery product is poor, but the sales of livestock is very efficient. Effectivity level of livestock and fishery product sales are low, whileretribution slaughterhouses(RPH is not effective regarded to its potential but in the contrary for its target. Contribution of PAD admission of Fishery and Animal Husbandry Department is very low regarded Tebo Regency PAD. The result of SWOT analysis of retribution slaughter house (RPH admission using WO (Weakness-Opportunity strategy, livestock sales using SO (Strength-Oppurtunity strategy, and fishery product sales using ST (strength-threat strategy. Keywords: Retribution SlaughterHouse (RPH, Sales of Fishery, Livestock Sales, SWOT Analysis Abstrak. Penelitian ini bertujuan untuk menganalisis potensi, efisiensi, efektivitas dan kontribusi penerimaan PAD pada Dinas Perikanan dan Peternakan Kabupaten Teboserta menetapkan strategi untuk peningkatan penerimaan PAD. Analisis yang digunakan adalah rumus potensi, rasio efisiensi, rasio efektivitas, rasio kontribusi dan analisis SWOT.Hasil penelitian menunjukkan bahwa potensi penerimaan retribusi rumah potong hewan (RPH, potensi penjualan hasil peternakan, potensi penjualan hasil perikanan lebih besar dari target yang telah ditetapkan. Tingkat efisiensi retribusi RPH dan penjualan hasil perikanan tidak efisien, penjualan hasil peternakan sangat efisien. Tingkat
Vortex Dynamics in Superconductors with Different Types of Pinning Potentials
International Nuclear Information System (INIS)
Laguna, Maria Fabiana
2001-01-01
In this work we study the behavior of the vortex system in the mixed state of a type II superconductor when it interacts with different kinds of pinning potentials. To do this, we perform numerical simulations in the presence of an external magnetic field, by making use of two different approaches.One corresponds to a Langevin simulation of the three dimensional XY model or Josephson-junction network, whereas the other corresponds to a Molecular dynamics simulation of two dimensional point-like vortices.We analyze the transport properties of highly anisotropic superconductors with different kinds of topological disorder in the configuration in which the external field is applied perpendicular to the CuO planes.We found that for systems with point defects the activation energy is the same for the two components of the resistivity, while in systems with columnar defects the activation energies can be different.We also study the structure, phase transitions and transport properties of the vortex system when the external magnetic field lies parallel to the planes in layered superconductors. We analyze the stability of different phases at low temperatures and show under which conditions the smectic phase is stable.Our results indicate the presence of the smectic phase in an intermediate range of temperatures.We have studied a vortex array in a periodic pinning potential with triangular and kagome geometries.We obtain the ground state vortex configurations and calculate some thermodynamic quantities for different magnetic fields.We observe several stages of lattice pinning and melting and we characterize different phases and transitions between them.Finally, simulating the Bitter pinning effect over the vortex system, we study static and dynamic properties of the vortex system in the presence of the surface Bitter pinning and the bulk pinning.We found low temperature structures similar to those obtained experimentally.We analyze the dynamics of the nucleation and growth
Flux pinning in MOD YBCO films by chemical doping
International Nuclear Information System (INIS)
Zhou, Y X; Ghalsasi, S; Rusakova, I; Salama, K
2007-01-01
A novel nanomaterial synthesis technique has been developed to introduce 0D (particles), 1D (columnar defects) and 3D (domains) nanoscale pinning centres in MOD Y 1 Ba 2 Cu 3 O 7 (YBCO) coated conductors. We have succeeded in introducing nanoscale Y enriched particles, nanoscale 90 0 rotated Y 1/3 Sm 2/3 Ba 2 Cu 3 O 7 domains and nanoscale Zr enriched columnar defects into YBCO layers by different chemical doping. The pinning force density in Y 2 O 3 -doped YBCO film is found to be larger than that of pure YBCO film at all fields. Also it was found that YBCO films with Sm substituting for Y have yielded improved critical current density characteristics over a wide range of magnetic fields. Maximum pinning force densities exceeding 7 and 8 GN m -3 are obtained in 5% BZO-doped and Sm substituted YBCO films, respectively. Additionally, TEM studies revealed nanoscale Zr enriched columnar defects distributing in the matrix of the c-oriented YBCO film throughout the whole cross section. This indicates that chemical doping is a promising fabrication technique to create specific pinning landscapes in YBCO coated conductors
Spectroscopic amplifier for pin diode; Amplificador espectroscopico para diodo Pin
Energy Technology Data Exchange (ETDEWEB)
Alonso M, M. S.; Hernandez D, V. M.; Vega C, H. R., E-mail: bebe.luna_s@hotmail.com [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas (Mexico)
2014-10-15
The photodiode remains the basic choice for the photo-detection and is widely used in optical communications, medical diagnostics and field of corpuscular radiation. In detecting radiation it has been used for monitoring radon and its progeny and inexpensive spectrometric systems. The development of a spectroscopic amplifier for Pin diode is presented which has the following characteristics: canceler Pole-Zero (P/Z) with a time constant of 8 μs; constant gain of 57, suitable for the acquisition system; 4th integrator Gaussian order to waveform change of exponential input to semi-Gaussian output and finally a stage of baseline restorer which prevents Dc signal contribution to the next stage. The operational amplifier used is the TLE2074 of BiFET technology of Texas Instruments with 10 MHz bandwidth, 25 V/μs of slew rate and a noise floor of 17 nv/(Hz)1/2. The integrated circuit has 4 operational amplifiers and in is contained the total of spectroscopic amplifier that is the goal of electronic design. The results show like the exponential input signal is converted to semi-Gaussian, modifying only the amplitude according to the specifications in the design. The total system is formed by the detector, which is the Pin diode, a sensitive preamplifier to the load, the spectroscopic amplifier that is what is presented and finally a pulse height analyzer (Mca) which is where the spectrum is shown. (Author)
Energy Technology Data Exchange (ETDEWEB)
El-Tayeb, A., E-mail: ahmed.khalil@ejust.edu.eg; El-Shazly, A. H.; Elkady, M. F. [Egypt−Japan University of Science and Technology, Chemicals and Petrochemicals Engineering Department (Egypt); Abdel-Rahman, A. B. [Egypt−Japan University of Science and Technology, Electronics and Communications Engineering Department (Egypt)
2016-09-15
In this article, a dual pin-to-plate high-voltage corona discharge system is introduced to study experimentally the gap distance, the contact time, the effect of pin and plate materials, the thickness of ground plate and the conductivity on the amount of Acid Blue 25 dye color removal efficiency from polluted water. A study for the optimum air gap distance between dual pin and surface of Acid Blue 25 dye solution is carried out using 3D-EM simulator to find maximum electric field intensity at the tip of both pins. The outcomes display that the best gap for corona discharge is approximately 5 mm for 15-kV source. This separation is constant during the study of other factors. In addition, an investigation of the essential reactive species responsible for oxidation of the dye organic compounds (O{sub 3} in air discharge, O{sub 3} in water, and H{sub 2}O{sub 2}) during the experimental time is conducted. Three various materials such as: stainless steel, copper and aluminum are used for pins and plate. The maximum color removal efficiencies of Acid Blue 25 dyes are 99.03, 82.04, and 90.78% after treatment time 15 min for stainless steel, copper, and aluminum, respectively. Measurement results for the impact of thickness of an aluminum ground plate on color removal competence show color removal efficiencies of 86.3, 90.78, and 98.06% after treatment time 15 min for thicknesses of 2, 0.5, and 0.1 mm, respectively. The increasing of the solution conductivity leads to the reduction of decolorization efficiency. A kinetic model is used to define the performance of corona discharge system. The models of pseudo-zero-order, pseudo-first-order, and pseudo-second-order reaction kinetics are utilized to investigate the decolorization of Acid Blue 25 dye. The rate of degradation of Acid Blue 25 dye follows the pseudo-first-order kinetics in the dye concentration.
International Nuclear Information System (INIS)
El-Tayeb, A.; El-Shazly, A. H.; Elkady, M. F.; Abdel-Rahman, A. B.
2016-01-01
In this article, a dual pin-to-plate high-voltage corona discharge system is introduced to study experimentally the gap distance, the contact time, the effect of pin and plate materials, the thickness of ground plate and the conductivity on the amount of Acid Blue 25 dye color removal efficiency from polluted water. A study for the optimum air gap distance between dual pin and surface of Acid Blue 25 dye solution is carried out using 3D-EM simulator to find maximum electric field intensity at the tip of both pins. The outcomes display that the best gap for corona discharge is approximately 5 mm for 15-kV source. This separation is constant during the study of other factors. In addition, an investigation of the essential reactive species responsible for oxidation of the dye organic compounds (O 3 in air discharge, O 3 in water, and H 2 O 2 ) during the experimental time is conducted. Three various materials such as: stainless steel, copper and aluminum are used for pins and plate. The maximum color removal efficiencies of Acid Blue 25 dyes are 99.03, 82.04, and 90.78% after treatment time 15 min for stainless steel, copper, and aluminum, respectively. Measurement results for the impact of thickness of an aluminum ground plate on color removal competence show color removal efficiencies of 86.3, 90.78, and 98.06% after treatment time 15 min for thicknesses of 2, 0.5, and 0.1 mm, respectively. The increasing of the solution conductivity leads to the reduction of decolorization efficiency. A kinetic model is used to define the performance of corona discharge system. The models of pseudo-zero-order, pseudo-first-order, and pseudo-second-order reaction kinetics are utilized to investigate the decolorization of Acid Blue 25 dye. The rate of degradation of Acid Blue 25 dye follows the pseudo-first-order kinetics in the dye concentration.
Pin and roller attachment system for ceramic blades
Shaffer, J.E.
1995-07-25
In a turbine, a plurality of blades are attached to a turbine wheel by way of a plurality of joints which form a rolling contact between the blades and the turbine wheel. Each joint includes a pin and a pair of rollers to provide rolling contact between the pin and an adjacent pair of blades. Because of this rolling contact, high stress scuffing between the blades and the turbine wheel reduced, thereby inhibiting catastrophic failure of the blade joints. 3 figs.
Measurement of contact angle in a clearance-fit pin-loaded hole
Prabhakaran, R.; Naik, R. A.
1986-01-01
A technique which measures load-contact variation in a clearance-fit, pin-loaded hole is presented in detail. A steel instrumented pin, which activates a make-or-break electrical circuit in the pin-hole contact region, was inserted into one aluminum and one polycarbonate specimen. The resulting load-contact variations are indicated schematically. The ability to accurately determine the arc of contact at any load was crucial to this measurement. It is noted that this simple experimental technique is applicable to both conducting and nonconducting materials.
Theoretical interpretation of SCARABEE single pin in-pile boiling experiments
International Nuclear Information System (INIS)
Struwe, D.; Bottoni, M.; Fries, W.; Elbel, H.; Angerer, G.
1977-01-01
In the framework of LMFBR safety analysis a theoretical interpretation of some of the most representative of the single pin experiments of the in-pile SCARABEE project has been performed from both viewpoints of thermohydraulic and fuel behaviour using the computer codes CAPRI-2 and SATURN-1. The analysis is aimed at investigating the pin behavior from the preirradiation history, through the observed sequence of events following a coolant mass flow reduction from boiling inception up to pin breakdown. A comparison of theoretical results with experimentally recorded data has allowed a deeper insight into the peculiar features of the experiments and enabled a valuable code verification. (Auth.)
Evaluation of bundle duct interaction by out-of-pile compression test of FBR fuel pin bundles
Energy Technology Data Exchange (ETDEWEB)
Tanaka, Kosuke; Yamamoto, Yuji; Nagamine, Tsuyoshi; Maeda, Koji [Japan Nuclear Cycle Development Inst., Oarai, Ibaraki (Japan). Oarai Engineering Center
2001-06-01
Bundle duct interaction (BDI) caused by expansion of fuel pin bundle is a main factor to limit the fuel lifetime. Therefore, it is important for the design of fast reactor fuel assembly to understand the fuel pin deformation behavior under BDI condition. In order to understand the fuel pin deformation behavior under BDI condition, out-of-pile compression tests were conducted for FBR fuel pin bundle by use of X-ray CT equipment. In these compression tests, two kinds of fuel pin bundles were conducted. One was the fuel pin bundle with the short wire-pitch and the other was the fuel pin bundle with the short wire-pitch and large diameter claddings. The general discussions were also performed based on the results of out-of-pile compression tests obtained by use of X-ray CT equipment in the previous work. Following results were obtained. 1) The occurrence of the pin-to-duct contact depends on the wire-pitch. In the fuel pin bundle with large wire-pitch, the pin-to-duct contact occurred at the early stage of BDI. The reason of this result is due to the low bowing rigidity of the fuel pins with long wire-pitch. 2) The value of the ovalation stiffness strongly depends on the geometry of cladding (diameter, thickness) and especially on wire-pitch. This result in this work revealed that the occurrence of the pin-to-duct contact depends on the value of the ovalation stiffness. 3) The occurrence of wire dispersion and dispersive displacement of pins depends on the wire-pitch strongly. In the fuel pin bundle with the long wire-pitch, the occurrence of the above-mentioned suppression mechanism to BDI is remarkable. 4) The suppression mechanism to BDI of the fuel pin bundle with the long wire-pitch is elastic oval deformation of cladding, wire dispersion and dispersive displacement of pins. On the other hand, the elastic and plastic oval deformation of cladding is the major suppression mechanism to BDI in the fuel pin bundle with the short wire-pitch. 5) The appearance of
Simulations of vortices in a star-shaped plate with an artificial pin
Miyoshi, Hiroki; Ito, Atsuki; Dang, Vu The; Thanh Huy, Ho; Hayashi, Masahiko; Kato, Masaru; Ishida, Takekazu
2017-07-01
Although a triangular vortex lattice is stable in a bulk type-II superconductor, exotic vortex configurations are expected to appear in a small superconducting plate. Theoretical calculations on vortex structures in a star-shaped superconducting plate have been given in our preceding work. In this work, we extended our theoretical studies to the case of having an artificial pin. We performed the Ginzburg-Landau (GL) calculations systematically to compare with the pin-free case by using the finite element method. We found that a vortex tends to accommodate preferentially in an aritificial pin in the star-shaped plate. We found a systematic evolution of vortex structure with increaseing magnetic field. We compare our theoretical calculations with vortices in a star-shaped Mo80Ge20 plate with an artificial pin and without an artificial pin obtained by a scanning SQUID microscope. We reconstructed the vortex image on the sample surface by using the inverse Biot-Savart law and the Fourier transformation.
Friction Stir Welding of Tapered Thickness Welds Using an Adjustable Pin Tool
Adams, Glynn; Venable, Richard; Lawless, Kirby
2003-01-01
Friction stir welding (FSW) can be used for joining weld lands that vary in thickness along the length of the weld. An adjustable pin tool mechanism can be used to accomplish this in a single-pass, full-penetration weld by providing for precise changes in the pin length relative to the shoulder face during the weld process. The difficulty with this approach is in accurately adjusting the pin length to provide a consistent penetration ligament throughout the weld. The weld technique, control system, and instrumentation must account for mechanical and thermal compliances of the tooling system to conduct tapered welds successfully. In this study, a combination of static and in-situ measurements, as well as active control, is used to locate the pin accurately and maintain the desired penetration ligament. Frictional forces at the pin/shoulder interface were a source of error that affected accurate pin position. A traditional FSW pin tool design that requires a lead angle was used to join butt weld configurations that included both constant thickness and tapered sections. The pitch axis of the tooling was fixed throughout the weld; therefore, the effective lead angle in the tapered sections was restricted to within the tolerances allowed by the pin tool design. The sensitivity of the FSW process to factors such as thickness offset, joint gap, centerline offset, and taper transition offset were also studied. The joint gap and the thickness offset demonstrated the most adverse affects on the weld quality. Two separate tooling configurations were used to conduct tapered thickness welds successfully. The weld configurations included sections in which the thickness decreased along the weld, as well as sections in which the thickness increased along the weld. The data presented here include weld metallography, strength data, and process load data.
Flux pinning in La70 Cu30 disordered system
International Nuclear Information System (INIS)
Esquinazi, P.; Guillet, B.; Dussell, H.
1983-09-01
Superconducting critical currents were measured as a function of a perpendicular applied magnetic field in disordered La 70 Cu 30 . It is shown that the pinning force is very sensitive to inhomogeneties already present in the as quenched samples, although these inhomogeneties have no obvious influence on other superconducting and transport properties. A simple series resistance model is used to explain the magnetic field dependence of the pinning force. A large decrease of the pinning force was obtained for the annealed samples. This behaviour is consistent with the phase separation model that explains the evolution of the superconductive penetration depth. In order to obtain a better characterization of the structural evolution with annealing of the La 70 Cu 30 system, behaviour of the electrical resistivity, superconducting critical temperature and differential thermal analysis were measured. (author)
Environment-based pin-power reconstruction method for homogeneous core calculations
International Nuclear Information System (INIS)
Leroyer, H.; Brosselard, C.; Girardi, E.
2012-01-01
Core calculation schemes are usually based on a classical two-step approach associated with assembly and core calculations. During the first step, infinite lattice assemblies calculations relying on a fundamental mode approach are used to generate cross-sections libraries for PWRs core calculations. This fundamental mode hypothesis may be questioned when dealing with loading patterns involving several types of assemblies (UOX, MOX), burnable poisons, control rods and burn-up gradients. This paper proposes a calculation method able to take into account the heterogeneous environment of the assemblies when using homogeneous core calculations and an appropriate pin-power reconstruction. This methodology is applied to MOX assemblies, computed within an environment of UOX assemblies. The new environment-based pin-power reconstruction is then used on various clusters of 3x3 assemblies showing burn-up gradients and UOX/MOX interfaces, and compared to reference calculations performed with APOLLO-2. The results show that UOX/MOX interfaces are much better calculated with the environment-based calculation scheme when compared to the usual pin-power reconstruction method. The power peak is always better located and calculated with the environment-based pin-power reconstruction method on every cluster configuration studied. This study shows that taking into account the environment in transport calculations can significantly improve the pin-power reconstruction so far as it is consistent with the core loading pattern. (authors)
Fuel-sodium reaction product formation in breached mixed-oxide fuel
International Nuclear Information System (INIS)
Bottcher, J.H.; Lambert, J.D.B.; Strain, R.V.; Ukai, S.; Shibahara, S.
1988-01-01
The run-beyond-cladding-breach (RBCB) operation of mixed-oxide LMR fuel pins has been studied for six years in the Experimental Breeder Reactor-II (EBR-II) as part of a joint program between the US Department of Energy and the Power Reactor and Nuclear Fuel Development Corporation of Japan. The formation of fuel-sodium reaction product (FSRP), Na 3 MO 4 , where M = U/sub 1-y/Pu/sub y/, in the outer fuel regions is the major phenomenon governing RBCB behavior. It increases fuel volume, decreases fuel stoichiometry, modifies fission-product distributions, and alters thermal performance of a pin. This paper describes the morphology of Na 3 MO 4 observed in 5.84-mm diameter pins covering a variety of conditions and RBCB times up to 150 EFPD's. 8 refs., 1 fig
Harwaningrum, Miranti
2016-01-01
Beberapa tahun belakangan ini, dunia investasi mengalami peningkatan. Hal ini dapat terlihat dari data rata-rata perdagangan saham yang dimiliki oleh Bapepam. Salah satu jenis instrumen investasi yang sering diminati oleh investor adalah saham. Apabila dibandingkan dengan obligasi, saham memiliki expected return yang lebih tinggi. Namun, saham memiliki resiko yang lebih tinggi bila dibandingkan dengan obligasi. Untuk melakukan penilaian saham ada dua analisis yang dapat dilakukan, yaitu funda...
Dong, Huan; Mukinay, Tatiana; Li, Maojun; Hood, Richard; Soo, Sein Leung; Cockshott, Simon; Sammons, Rachel; Li, Xiaoying
2017-01-01
In this study, an advanced ceramic conversion surface engineering technology has been applied for the first time to self-drilling Ti6Al4V external fixation pins to improve their performance in terms of biomechanical, bio-tribological and antibacterial properties. Systematic characterisation of the ceramic conversion treated Ti pins was carried out using Scanning electron microscope, X-ray diffraction, Glow-discharge optical emission spectroscopy, nano- and micro-indentation and scratching; the biomechanical and bio-tribological properties of the surface engineered Ti pins were evaluated by insertion into high density bone simulation material; and the antibacterial behaviour was assessed with Staphylococcus aureus NCTC 6571. The experimental results have demonstrated that the surfaces of Ti6Al4V external fixation pins were successfully converted into a TiO 2 rutile layer (~2 μm in thickness) supported by an oxygen hardened case (~15 μm in thickness) with very good bonding due to the in-situ conversion nature. The maximum insertion force and temperature were reduced from 192N and 31.2 °C when using the untreated pins to 182N and 26.1 °C when the ceramic conversion treated pins were tested. This is mainly due to the significantly increased hardness (more than three times) and the effectively enhanced wear resistance of the cutting edge of the self-drilling Ti pins following the ceramic conversion treatment. The antibacterial tests also revealed that there was a significantly reduced number of bacteria isolated from the ceramic conversion treated pins compared to the untreated pins of around 50 % after 20 h incubation, P < 0.01 (0.0024). The results reported are encouraging and could pave the way towards high-performance anti-bacterial titanium external fixation pins with reduced pin-track infection and pin loosing.
International Nuclear Information System (INIS)
Toyota, Shun; Seta, Hidetoshi; Muramatsu, Masatoshi; Kubo, Hitoshi; Takeda, Kan
2003-01-01
In stereotactic radiosurgery (SRS), fixation devices are secured to the patient's head with pins. However, there have been no standards for the use of such pins, which must be inserted with appropriate torque based on the surgeon's clinical judgment. Therefore, the pins may sometimes be tightened excessively and penetrate too deeply into the patient's skull. To improve safety in SRS, a torque wrench was used for pin insertion. The usefulness of the torque wrench was then evaluated by examining the relationships between the pins and skull bone and identifying differences according to the wrench used and the patient's bone thickness. CT images of patients who had previously undergone SRS were used to assess the relationships between the pins and skull bone. Differences according to the wrench used and pin insertion site were investigated. Compared with a standard wrench, use of the torque wrench decreased the insertion depth of pins in the skull bone. In terms of site, pins in the forehead were inserted more deeply. No differences related to the frontal sinus were observed. The use of a torque wrench improved safety during pin insertion for SRS procedures. (author)
Advanced control system for the Integral Fast Reactor fuel pin processor
International Nuclear Information System (INIS)
Lau, L.D.; Randall, P.F.; Benedict, R.W.; Levinskas, D.
1993-01-01
A computerized control system has been developed for the remotely-operated fuel pin processor used in the Integral Fast Reactor Program, Fuel Cycle Facility (FCF). The pin processor remotely shears cast EBR- reactor fuel pins to length, inspects them for diameter, straightness, length, and weight, and then inserts acceptable pins into new sodium-loaded stainless-steel fuel element jackets. Two main components comprise the control system: (1) a programmable logic controller (PLC), together with various input/output modules and associated relay ladder-logic associated computer software. The PLC system controls the remote operation of the machine as directed by the OCS, and also monitors the machine operation to make operational data available to the OCS. The OCS allows operator control of the machine, provides nearly real-time viewing of the operational data, allows on-line changes of machine operational parameters, and records the collected data for each acceptable pin on a central data archiving computer. The two main components of the control system provide the operator with various levels of control ranging from manual operation to completely automatic operation by means of a graphic touch screen interface
TRANSPA: a code for transient thermal analysis of a single fuel pin
International Nuclear Information System (INIS)
Prenger, F.C.
1985-02-01
An analytical model (TRANSPA) for the transient thermal analysis of a single uranium carbide fuel pin was developed. This model uses thermal boundary conditions obtained from COBRA-WC output and calculates the transient thermal response of a single fuel pin to changes in internal power generation, coolant flowrate, or fuel pin physical configuration. The model uses the MITAS finite difference thermal analyzer. MITAS provides the means to input separate conductance models through the use of a user subroutine input capability. The model is a lumped-mass representation of the fuel pin using 26 nodes and 42 conductors. Run time for each transient analysis is approximately one minute of central processor time on the NOS operating system
Serviceability of rod ceramic fuel pins on motoring conditions of FTP or NEMF reactor
International Nuclear Information System (INIS)
Deryavko, I.I.
2004-01-01
The operation conditions of rod ceramic fuel pins in the running hydrogen-cooled technological canals of FTP or NEMF reactor on the motoring conditions are considered. The available postreactor researches of the fuel pins are presented and the additional postreactor researches of fuel pins, tested on this mode in IVG.1 and IRGIT reactors, are carried out. The fuel pins serviceability on motoring conditions of FTP or NEF reactor operation is concluded. (author)
ANALISIS MODEL PREDIKSI AWAL MUSIM HUJAN DI SULAWESI SELATAN
Directory of Open Access Journals (Sweden)
Alimatul Rahim
2016-03-01
Full Text Available Model prediksi awal musim hujan merupakan salah satu kunci yang dapat digunakan untuk mengurangi resiko kegagalan panen padi yang disebabkan oleh faktor iklim di provinsi Sulawesi Selatan. Model prediksi awal musim hujan dibangun dengan menggunakan data curah hujan observasi Sulawesi Selatan dan anomali suhu muka laut di kawasan Pasifik dan perairan Sulawesi. Pada studi ini dilakukan analisis pemilihan stasiun hujan observasi, penentuan awal musim hujan, analisis komponen utama dan pengelompokan, analisis korelasi awal musim hujan terhadap anomali suhu muka laut, pembangunan model untuk prediksi awal musimhujan dan verifikasi model.Hasil analisis awal musim hujan menunjukkan setiap stasiun hujan mempunyai perbedaan awal musim hujan dengan rata-rata jatuh pada Julian Date (JD ke-348 (14 Desember. Berdasarkan hasil analisis PCA dan cluster, diperoleh bahwa di Sulawesi Selatan terbagi menjadi 3 cluster wilayah. Cluster 1 mempunyai pola hujan lokal, sedangkan cluster 2 dan 3 mempunyai pola hujan monsun. Pada peta korelasi antara awal musim hujan di Sulawesi Selatan dan anomali suhu muka laut menunjukkan bahwa terdapat korelasi nyata(r≥0.5 antara kawasan Pasifik dan Laut Sulawesi pada cluster 1 dan 2 pada bulan Juni Juli Agustus September(JJAS. Sedangkan pada cluster 3, korelasi nyata hanya pada bulan Juni di perairan Sulawesi. Model prediksi AMH terbaik, pada cluster 2 terdapat di domain prediktor kawasan pasifik dengan nilai r=0.82, sedangkan pada cluster 1 dan 3, terdapat di domain perairan Sulawesi dengan nilai r=0.78 dan r-0.48. Verifikasi model terpilih pada cluster 3 mempunyai RMSE = 3, sedangkan cluster 1 dan 2, nilai RMSE berturut-turut sebesar 16 dan 29. Model prediction of rainy season onset is one of the keys to reduce the risk of paddy haverst failure because of climate factor in South Sulawesi province. The model prediction for rainy season onset was build using rainfall data in South Sulawesi and SST anomaly in Pacific Ocean and
The interpretation of fuel centre temperature measurements on a suspected leaking fuel pin
International Nuclear Information System (INIS)
Ainscough, J.B.; Lang, C.; Clough, D.J.
1983-01-01
In order to study fuel densification a series of single instrumented pin irradiations has been carried out in the High Pressure Water Loop of DIDO at Harwell. The behaviour of two of these pins was different from that expected. In the fifth test, where the fuel was 95% dense pellet UO 2 and expected to densify readily in-reactor, the fuel centre temperature increased from its starting value of approx. 1300 deg. C at a rate somewhat higher than expected on the basis of predicted densification rates. After about six days, the temperature increased rapidly and unexpectedly to 2100-2200 deg. C and remained steady at this level for a further eight days until a reactor trip occurred and the pin was unloaded. Predictions made using the HOTROD code imply a maximum fuel temperature of less than 1500 deg. C after densification. Post-irradiation examination confirmed that fission gas release had occurred, that the measured temperatures were consistent with the fuel microstructure and that the pin had a high internal gas pressure. The fourth pin in the series contained 97% dense UO 2 which was also expected to be dimensionally unstable. Qualitatively its behaviour was similar to that of the fifth pin though the temperatures throughout were lower. This pin experienced a number of major power cycles and failed after about 30 days in-reactor. It is probable that coolant ingress occurred in both pins via the thermocouple Hoke seal, degrading the filling gas conductivity and allowing the fuel to densify rapidly with consequent increase in the fuel/clad gap and hence in fuel temperature. These irradiations show that, for a short time at least, an apparently unfailed pin could operate undetected with temperatures significantly higher than those predicted for normal operation. (author)
Fuel pin failure in the PFR/TREAT experiments
International Nuclear Information System (INIS)
Herbert, R.; Hunter, C.W.; Kramer, J.M.; Wood, M.H.; Wright, A.E.
1986-01-01
The PFR/TREAT safety testing programme involves the transient testing of fresh and pre-irradiated UK and US fuel pins. This paper summarizes the experimental and calculational results obtained to date on fuel pin failure during transient overpower (resulting from an accidental addition of resolivity) and transient undercooling followed by overpower (arising from an accidental stoppage of the primary sodium circulating pumps) accidents. Companion papers at this conference address: (I) the progress and future plans of the programme, and (II) post-failure material movements
Radiation monitoring with CVD diamonds and PIN diodes at BaBar
Energy Technology Data Exchange (ETDEWEB)
Bruinsma, M. [University of California Irvine, Irvine, CA 92697 (United States); Burchat, P. [Stanford University, Stanford, CA 94305-4060 (United States); Curry, S. [University of California Irvine, Irvine, CA 92697 (United States)], E-mail: scurry@slac.stanford.edu; Edwards, A.J. [Stanford University, Stanford, CA 94305-4060 (United States); Kagan, H.; Kass, R. [Ohio State University, Columbus, OH 43210 (United States); Kirkby, D. [University of California Irvine, Irvine, CA 92697 (United States); Majewski, S.; Petersen, B.A. [Stanford University, Stanford, CA 94305-4060 (United States)
2007-12-11
The BaBar experiment at the Stanford Linear Accelerator Center has been using two polycrystalline chemical vapor deposition (pCVD) diamonds and 12 silicon PIN diodes for radiation monitoring and protection of the Silicon Vertex Tracker (SVT). We have used the pCVD diamonds for more than 3 years, and the PIN diodes for 7 years. We will describe the SVT and SVT radiation monitoring system as well as the operational difficulties and radiation damage effects on the PIN diodes and pCVD diamonds in a high-energy physics environment.
Peripheral pin alignment system for fuel assemblies
International Nuclear Information System (INIS)
Anthony, A.J.
1981-01-01
An alignment system is provided for nuclear fuel assemblies in a nuclear core. The core support structure of the nuclear reactor includes upwardly pointing alignment pins arranged in a square grid and engage peripheral depressions formed in the lateral periphery of the lower ends of each of the fuel assemblies of the core. In a preferred embodiment, the depressions are located at the corners of the fuel assemblies so that each depression includes one-quarter of a cylindrical void. Accordingly, each fuel assembly is positioned and aligned by one-quarter of four separate alignment pins which engage the fuel assemblies at their lower exterior corners. (author)
Chemical Emulation of Radiation Pinning Center Geometries in High Temperature Superconductors
National Research Council Canada - National Science Library
Weinstein, Roy
2004-01-01
...). Discovery of an entire class of 200-400 nm size, double perovskite pinning centers, (A,B)REBa(sub 2)O(sub 6), led to 20 new chemical "point" pinning centers, and enabled replacement of successful but expensive and radioactive...
Li, X T; Huang, L J; Wei, S L; An, Q; Cui, X P; Geng, L
2018-04-10
Controlled and compacted TiAl 3 coating was successfully fabricated on the network structured TiBw/Ti6Al4V composites by hot-dipping aluminum and subsequent interdiffusion treatment. The network structure of the composites was inherited to the TiAl 3 coating, which effectively reduces the thermal stress and avoids the cracks appeared in the coating. Moreover, TiB reinforcements could pin the TiAl 3 coating which can effectively improve the bonding strength between the coating and composite substrate. The cycle oxidation behavior of the network structured coating on 873 K, 973 K and 1073 K for 100 h were investigated. The results showed the coating can remarkably improve the high temperature oxidation resistance of the TiBw/Ti6Al4V composites. The network structure was also inherited to the Al 2 O 3 oxide scale, which effectively decreases the tendency of cracking even spalling about the oxide scale. Certainly, no crack was observed in the coating after long-term oxidation due to the division effect of network structured coating and pinning effect of TiB reinforcements. Interfacial reaction between the coating and the composite substrate occurred and a bilayer structure of TiAl/TiAl 2 formed next to the substrate after oxidation at 973 K and 1073 K. The anti-oxidation mechanism of the network structured coating was also discussed.
Directory of Open Access Journals (Sweden)
Ramiro París
2018-04-01
Full Text Available High-resolution and automated image analysis of individual roots demonstrated that endogenous nitric oxide (NO contribute significantly to gravitropism of Arabidopsis roots. Lowering of endogenous NO concentrations strongly reduced and even reversed gravitropism, resulting in upward bending, without affecting root growth rate. Notably, the asymmetric accumulation of NO along the upper and lower sides of roots correlated with a positive gravitropic response. Detection of NO by the specific DAF-FM DA fluorescent probe revealed that NO was higher at the lower side of horizontally-oriented roots returning to initial values 2 h after the onset of gravistimulation. We demonstrate that NO promotes plasma membrane re-localization of PIN2 in epidermal cells, which is required during the early root gravitropic response. The dynamic and asymmetric localization of both auxin and NO is critical to regulate auxin polar transport during gravitropism. Our results collectively suggest that, although auxin and NO crosstalk occurs at different levels of regulation, they converge in the regulation of PIN2 membrane trafficking in gravistimulated roots, supporting the notion that a temporally and spatially coordinated network of signal molecules could participate in the early phases of auxin polar transport during gravitropism.
La financial education nella regione Puglia: analisi e prospettive di intervento
A. Garzoni; V. Nastasi
2010-01-01
Analisi del contesto e delle principali tematiche di financial education affrontate a livello internazionale e nazionale, valutazione delle opportunità e degli aspetti critici, il progetto pilota nella regione Puglia e le nuove idee di progetto da realizzare
Flexible Electronics Powered by Mixed Metal Oxide Thin Film Transistors
Marrs, Michael
A low temperature amorphous oxide thin film transistor (TFT) and amorphous silicon PIN diode backplane technology for large area flexible digital x-ray detectors has been developed to create 7.9-in. diagonal backplanes. The critical steps in the evolution of the backplane process include the qualification and optimization of the low temperature (200 °C) metal oxide TFT and a-Si PIN photodiode process, the stability of the devices under forward and reverse bias stress, the transfer of the process to flexible plastic substrates, and the fabrication and assembly of the flexible detectors. Mixed oxide semiconductor TFTs on flexible plastic substrates suffer from performance and stability issues related to the maximum processing temperature limitation of the polymer. A novel device architecture based upon a dual active layer improves both the performance and stability. Devices are directly fabricated below 200 ºC on a polyethylene naphthalate (PEN) substrate using mixed metal oxides of either zinc indium oxide (ZIO) or indium gallium zinc oxide (IGZO) as the active semiconductor. The dual active layer architecture allows for adjustment to the saturation mobility and threshold voltage stability without the requirement of high temperature annealing, which is not compatible with flexible plastic substrates like PEN. The device performance and stability is strongly dependent upon the composition of the mixed metal oxide; this dependency provides a simple route to improving the threshold voltage stability and drive performance. By switching from a single to a dual active layer, the saturation mobility increases from 1.2 cm2/V-s to 18.0 cm2/V-s, while the rate of the threshold voltage shift decreases by an order of magnitude. This approach could assist in enabling the production of devices on flexible substrates using amorphous oxide semiconductors. Low temperature (200°C) processed amorphous silicon photodiodes were developed successfully by balancing the tradeoffs
Study of fuel bundle geometry on inter subchannel flow in a 19 pin wire wrapped bundle
International Nuclear Information System (INIS)
Naveen Raj, M.; Velusamy, D.K.
2015-01-01
In typical sodium cooled fast reactor (SFR) fuel pin bundle, gap between the pins is maintained by helically wound wire wrap around each pin. The presence of wire induces large inter-subchannel transverse flow, eventually promoting mixing and heat transfer. The magnitude of the transverse flow is highly dependent on the various pin-bundle dimensions. Appropriate modeling of these transverse flows in subchannel codes is necessary to predict realistic temperature distribution in pin bundle. Hence, detailed parametric study of transverse flow on pin-bundle geometric parameters has been conducted. The parameters taken for the present study are pin diameter, wire diameter, helical wire pitch and edge gap. Towards this 3-D computational fluid dynamic analysis on a structured mesh of 19 pin bundle is carried out using k-epsilon turbulence model. Periodic oscillations along the primacy flow direction were found in subchannel transverse flow and peripheral pin clad temperatures with periodicity over one pitch length. Based on parametric studies, correlations for transverse flow in central subchannels are proposed. (author)
Text Mining Untuk Analisis Sentimen Review Film Menggunakan Algoritma K-Means
Directory of Open Access Journals (Sweden)
Setyo Budi
2017-02-01
Full Text Available Kemudahan manusia didalam menggunakan website mengakibatkan bertambahnya dokumen teks yang berupa pendapat dan informasi. Dalam waktu yang lama dokumen teks akan bertambah besar. Text mining merupakan salah satu teknik yang digunakan untuk menggali kumpulan dokumen text sehingga dapat diambil intisarinya. Ada beberapa algoritma yang di gunakan untuk penggalian dokumen untuk analisis sentimen, salah satunya adalah K-Means. Didalam penelitian ini algoritma yang digunakan adalah K-Means. Hasil penelitian menunjukkan bahwa akurasi K-Means dengan dataset digunakan 300 positif dan 300 negatif akurasinya 57.83%, 700 dokumen positif dan 700 negatif akurasinya 56.71%%, 1000 dokumen positif dan 1000 negatif akurasinya 50.40%%. Dari hasil pengujian disimpulkan bahwa semakin besar dataset yang digunakan semakin rendah akurasi K-Means. Kata Kunci : Text Mining, Analisis Sentimen, K-Means, Review Film
Analisis Nilai Perusahaan pada Implementasi Program Kepemilikan Saham pada Karyawan/Manajemen
Directory of Open Access Journals (Sweden)
Dwitya Aribawa
2016-12-01
Penelitian ini bertujuan menganalisis economic value added (EVA sebelum dan sesudah implementasi program kepemilikan saham pada karyawan/ manajemen dengan objek penelitian ini adalah perusahaan publik yang menggunakan kebijakan ESOP/MSOP sebagai sarana benefit/incentive berupa pembagian sebagian saham untuk karyawan/ manajemen. Variabel yang digunakan sebagai indikator nilai perusahaan adalah EVA. Nilai EVA dianggap sebagai indikator yang kompleks dan mempertimbangkan faktor resiko (beta dari perusahaan. Perusahaan yang dianalisis adalah perusahaan yang listing di Bursa Efek Indonesia. Terdapat 17 perusahaan yang layak untuk dilakukan analisis berdasarkan kriteria yang ditentukan peneliti. Pengumpulan dan data dianalisis secara pooling, hal ini melihat dari tidak dibedakannya perusahaan berdasarkan industri (multi industri. Paired sample test digunakan untuk menguji hipotesis pada penelitian dan sebelumnya dilakukan uji normalitas data. Hasil analisis bahwa hasil perbandingan rata-rata EVA sebelum dan sesudah implementasi program kepemilikan saham pada karyawan/manajemen terdapat perbedaan yag signifikan.
Flux vortex dynamics and electric fields in matched pinning systems
International Nuclear Information System (INIS)
Blamire, M.G.
1987-01-01
The pinning of flux vortices in type II superconductors has been the subject of extensive research. Certain experiments have attempted to investigate this problem by the use of specially prepared pinning structures consisting of regular arrays of pinning centers. In this paper a theory relating to such experiments is described. This theory is based on the existence and properties of defects in an otherwise perfect vortex lattice which is commensurate with a pinning array consisting of a triangular lattice of holes in a superconducting thin film. A quantitative treatment predicts the existence and position of substructure on the critical current versus magnetic field curves in addition to the main peaks previously predicted to occur when the vortex and hole lattices are exactly matched. The theory also qualitatively describes the overall shape of these curves. An analysis of the temperature dependence of this substructure shows broad agreement with existing experimental results. The application of this theory to future experiments should allow a detailed investigation of vortex lattice elasticity and flux flow
Propagation of spiral waves pinned to circular and rectangular obstacles.
Sutthiopad, Malee; Luengviriya, Jiraporn; Porjai, Porramain; Phantu, Metinee; Kanchanawarin, Jarin; Müller, Stefan C; Luengviriya, Chaiya
2015-05-01
We present an investigation of spiral waves pinned to circular and rectangular obstacles with different circumferences in both thin layers of the Belousov-Zhabotinsky reaction and numerical simulations with the Oregonator model. For circular objects, the area always increases with the circumference. In contrast, we varied the circumference of rectangles with equal areas by adjusting their width w and height h. For both obstacle forms, the propagating parameters (i.e., wavelength, wave period, and velocity of pinned spiral waves) increase with the circumference, regardless of the obstacle area. Despite these common features of the parameters, the forms of pinned spiral waves depend on the obstacle shapes. The structures of spiral waves pinned to circles as well as rectangles with the ratio w/h∼1 are similar to Archimedean spirals. When w/h increases, deformations of the spiral shapes are observed. For extremely thin rectangles with w/h≫1, these shapes can be constructed by employing semicircles with different radii which relate to the obstacle width and the core diameter of free spirals.
Zhao, Yu; Zhang, Li-Li; Ding, Fa-Xian; Cao, Ping; Qi, Yuan-Yuan; Wang, Jing
2017-11-01
Peptidyl-prolyl cis/trans isomerase NIMA-interacting 1 (Pin1) is a key regulator of PTH mRNA stability. Secondary hyperparathyroidism (SHPT), which is characterized by elevated serum PTH levels, is a common complication of CKD. We investigated the possible associations between CKD with SHPT (CKD SHPT) and single-nucleotide polymorphisms of the Pin1 gene and compared the levels of the Pin1 protein in the CKD SHPT patients with those of the controls. The study group included 251 CKD SHPT patients and 61 controls. One putative functional SNP (single nucleotide polymorphism) in the Pin1 promoter (rs2233679C > T: c.-667C > T) is the main object. Genotyping was performed on purified DNA using polymerase chain reaction-restriction (PCR) and restriction fragment length polymorphisms (RFLP). The levels of Pin1 were measured in serum using an enzyme-linked immunosorbent assay. Genotyping showed that CT + TT in the Pin1 promoter was significantly more common in the CKD SHPT group than in the control group (p<.05). The correlation analysis demonstrated that a significant difference in the C to T transition in the Pin1 promoter contributed to CKD SHPT (χ 2 =12.47, p<.05; Odds ratios (OR) = 1.26, 95% confidence (CI) intervals =1.06-1.49). The multivariate logistic regression analysis reported that the OR and 95%CI were 12.693 and 2.029-75.819 (p<.05), respectively, in the Pin1 gene promoter -667T variant genotypes (CT + TT) after adjusting for other factors, and those values in Pin1 were 0.310 and 0.122-0.792 (p<.05). The -667T genetic variants in the Pin1 promoter contribute to an increased risk of CKD SHPT and may be biomarkers of susceptibility to CKD SHPT.
JMCT Monte Carlo simulation analysis of full core PWR Pin-By-Pin and shielding
International Nuclear Information System (INIS)
Deng, L.; Li, G.; Zhang, B.; Shangguan, D.; Ma, Y.; Hu, Z.; Fu, Y.; Li, R.; Hu, X.; Cheng, T.; Shi, D.
2015-01-01
This paper describes the application of the JMCT Monte Carlo code to the simulation of Kord Smith Challenge H-M model, BEAVRS model and Chinese SG-III model. For H-M model, the 6.3624 millions tally regions and the 98.3 billion neutron histories do. The detailed pin flux and energy deposition densities obtain. 95% regions have less 1% standard deviation. For BEAVRS model, firstly, we performed the neutron transport calculation of 398 axial planes in the Hot Zero Power (HZP) status. Almost the same results with MC21 and OpenMC results are achieved. The detailed pin-power density distribution and standard deviation are shown. Then, we performed the calculation of ten depletion steps in 30 axial plane cases. The depletion regions exceed 1.5 million and 12,000 processors uses. Finally, the Chinese SG-III laser model is simulated. The neutron and photon flux distributions are given, respectively. The results show that the JMCT code well suits for extremely large reactor and shielding simulation. (author)
8 Pin RIC Socket for Hearing Aid Applications
DEFF Research Database (Denmark)
Islam, Aminul; Hansen, Hans Nørgaard; Davids, Søren
2012-01-01
process and the other one is fully automated process. This paper presents the entire process chain for both the concepts and makes a comparative analysis based on the experimental investigation and validation. The work presented here can be a source of valuable information for industrial users...... of them. 8 Pin RIC Socket is a functionally versatile product which can combine many different functions and presents many advantages compared with the previous 3 Pin RIC Socket. For the demonstrator production of the new Socket, two different production concepts were chosen- one based on semi-automated...
Pu, Wenchen; Li, Jiao; Zheng, Yuanyuan; Shen, Xianyan; Fan, Xin; Zhou, Jian-Kang; He, Juan; Deng, Yulan; Liu, Xuesha; Wang, Chun; Yang, Shengyong; Chen, Qiang; Liu, Lunxu; Zhang, Guolin; Wei, Yu-Quan; Peng, Yong
2018-01-30
Hepatocellular carcinoma (HCC) is a leading cause of cancer death worldwide, but there are few effective treatments. Aberrant microRNA (miRNA) biogenesis is correlated with HCC development. We previously demonstrated that peptidyl-prolyl cis-trans isomerase NIMA-interacting 1 (Pin1) participates in miRNA biogenesis and is a potential HCC treatment target. However, how Pin1 modulates miRNA biogenesis remains obscure. Here, we present in vivo evidence that Pin1 overexpression is directly linked to the development of HCC. Administration with the Pin1 inhibitor (API-1), a specific small molecule targeting Pin1 peptidyl-prolyl isomerase domain and inhibiting Pin1 cis-trans isomerizing activity, suppresses in vitro cell proliferation and migration of HCC cells. But API-1-induced Pin1 inhibition is insensitive to HCC cells with low Pin1 expression and/or low exportin-5 (XPO5) phosphorylation. Mechanistically, Pin1 recognizes and isomerizes the phosphorylated serine-proline motif of phosphorylated XPO5 and passivates phosphorylated XPO5. Pin1 inhibition by API-1 maintains the active conformation of phosphorylated XPO5 and restores XPO5-driven precursor miRNA nuclear-to-cytoplasm export, activating anticancer miRNA biogenesis and leading to both in vitro HCC suppression and HCC suppression in xenograft mice. Experimental evidence suggests that Pin1 inhibition by API-1 up-regulates miRNA biogenesis by retaining active XPO5 conformation and suppresses HCC development, revealing the mechanism of Pin1-mediated miRNA biogenesis and unequivocally supporting API-1 as a drug candidate for HCC therapy, especially for Pin1-overexpressing, extracellular signal-regulated kinase-activated HCC. (Hepatology 2018). © 2018 by the American Association for the Study of Liver Diseases.
Power release estimation inside of a fuel pin neighbouring a WWER-440 control rod
International Nuclear Information System (INIS)
Mikus, J.
2006-01-01
This work presents an estimation of the control rod (CR) influence in the WWER-440 core on the power release inside of a fuel pin neighbouring CR, that can have some consequences due to possible static and cyclic loads, for example fuel pin / fuel assembly bowing. For this purpose detailed (usual) axial power distribution measurements were performed in a WWER-440 type core on the light water, zero-power research reactor LR-0 in fuel pins near to an authentic CR model at zero boron concentration in moderator, modelling the conditions at the end of fuel cycle. To demonstrate the CR influence on power distribution inside of one fuel pin neighbouring CR, results of above measurements were used for estimation of the: 1) Axial power distribution inside of the investigated fuel pin in both opposite positions on its pellets surface that are situated to- and outwards CR and corresponding gradient of the (r, z) - power distribution in above opposite positions and 2) Azimuthal power distributions on pellet surface of the investigated fuel pin in horizontal planes at selected axial coordinates. Similar information can be relevant from the viewpoint of the fuel pin failures occurrence investigation
Kordestani, F.; Ashenai Ghasemi, F.; Arab, N. B. M.
2017-09-01
Friction stir welding (FSW) is a solid-state welding process, which has successfully been applied in aerospace and automotive industries for joining materials. The friction stir tool is the key element in the FSW process. In this study, the effect of four different tool pin geometries on the mechanical properties of two types of polypropylene composite plates, with 30% glass and carbon fiber, respectively, were investigated. For this purpose, four pins of different geometry, namely, a threaded-tapered pin, square pin, four-flute threaded pin, and threaded-tapered pin with a chamfer were made and used to carry out the butt welding of 5-mm-thick plates. The standard tensile and Izod impact tests were performed to evaluate the tensile strength and impact toughness of welded specimens. The results indicated that the threaded-tapered pin with a chamfer produced welds with a better surface appearance and higher tensile and impact strengths. The tests also showed that, with the threaded-tapered pin with a chamfer, the impact strength of the glass- and carbon-fiber composite welds were about 40 and 50%, respectively, of that of the base materials.
Cyclic movement pin mechanism for controlling a nuclear reactor
International Nuclear Information System (INIS)
Joly, J.G.; Martin, Jean.
1981-01-01
This invention concerns a recurring movement pin mechanism for controlling a nuclear reactor by shifting a neutron absorbing assembly, vertically mobile in the nuclear reactor, to adjust the power and for emergency shut-down. This mechanism ensures a continuous movement and accurate shut-down at any level of the travel height of the absorbing assembly in the core. It also prevents the impacts of the pivoting pins in the control rod slots [fr
Peptidyl Prolyl Isomerase PIN1 Directly Binds to and Stabilizes Hypoxia-Inducible Factor-1α.
Directory of Open Access Journals (Sweden)
Hyeong-Jun Han
Full Text Available Peptidyl prolyl isomerase (PIN1 regulates the functional activity of a subset of phosphoproteins through binding to phosphorylated Ser/Thr-Pro motifs and subsequently isomerization of the phosphorylated bonds. Interestingly, PIN1 is overexpressed in many types of malignancies including breast, prostate, lung and colon cancers. However, its oncogenic functions have not been fully elucidated. Here, we report that PIN1 directly interacts with hypoxia-inducible factor (HIF-1α in human colon cancer (HCT116 cells. PIN1 binding to HIF-1α occurred in a phosphorylation-dependent manner. We also found that PIN1 interacted with HIF-1α at both exogenous and endogenous levels. Notably, PIN1 binding stabilized the HIF-1α protein, given that their levels were significantly increased under hypoxic conditions. The stabilization of HIF-1α resulted in increased transcriptional activity, consequently upregulating expression of vascular endothelial growth factor, a major contributor to angiogenesis. Silencing of PIN1 or pharmacologic inhibition of its activity abrogated the angiogenesis. By utilizing a bioluminescence imaging technique, we were able to demonstrate that PIN1 inhibition dramatically reduced the tumor volume in a subcutaneous mouse xenograft model and angiogenesis as well as hypoxia-induced transcriptional activity of HIF-1α. These results suggest that PIN1 interacting with HIF-1α is a potential cancer chemopreventive and therapeutic target.
Two-dimensional nonlinear transient heat transfer analysis of variable section pin fins
Energy Technology Data Exchange (ETDEWEB)
Malekzadeh, P. [Department of Mechanical Engineering, School of Engineering, Persian Gulf University, Boushehr 75168 (Iran); Rahideh, H. [Department of Chemical Engineering, School of Engineering, Persian Gulf University, Boushehr 75168 (Iran)
2009-04-15
The two-dimensional nonlinear transient heat transfer analysis of variable cross section pin-fins is studied using the incremental differential quadrature method (IDQM) as a simple, accurate, and computationally efficient numerical tool. The formulations are general so that it can easily be used for arbitrary continuously varying cross section pin fins with the spatial-temperature dependent thermal parameters. On all external surfaces of the pin fin, the convective-radiative condition is considered. The effects of two different types of boundary conditions at the base of pin fin are investigated: time and spatial dependent temperature, and the convection heat transfer. The thermal conductivity of the pin fin is assumed to vary as a linear function of the temperature. The accuracy of the method is demonstrated by comparing its results with those generated by finite difference method. It is shown that using few grid points, results in excellent agreements with those of FDM are obtained. Less computational efforts of the method with respect to finite difference method is shown. (author)
International Nuclear Information System (INIS)
Llordes, Anna; Palau, A.; Gazquez, J.; Coll, M.; Vlad, R.; Pomar, A.; Arbiol, Jordi; Guzman, Roger; Ye, S.; Rouco, V.; Sandiumenge, Felip; Ricart, Susagna; Puig, Teresa; Varela del Arco, Maria; Chataigner, D.; Vanacken, J.; Gutierrez, J.; Moschalkov, V.; Deutscher, G.; Magen Dominguez, Cesar; Obradors, Xavier
2012-01-01
Boosting large-scale superconductor applications require nanostructured conductors with artificial pinning centres immobilizing quantized vortices at high temperature and magnetic fields. Here we demonstrate a highly effective mechanism of artificial pinning centers in solution-derived high-temperature superconductor nanocomposites through generation of nanostrained regions where Cooper pair formation is suppressed. The nanostrained regions identified from transmission electron microscopy devise a very high concentration of partial dislocations associated with intergrowths generated between the randomly oriented nanodots and the epitaxial YBa 2 Cu 3 O 7 matrix. Consequently, an outstanding vortex-pinning enhancement correlated to the nanostrain is demonstrated for four types of randomly oriented nanodot, and a unique evolution towards an isotropic vortex-pinning behaviour, even in the effective anisotropy, is achieved as the nanostrain turns isotropic. We suggest a new vortex-pinning mechanism based on the bond-contraction pairing model, where pair formation is quenched under tensile strain, forming new and effective core-pinning regions.
Timing analysis of PWR fuel pin failures
International Nuclear Information System (INIS)
Jones, K.R.; Wade, N.L.; Katsma, K.R.; Siefken, L.J.; Straka, M.
1992-09-01
Research has been conducted to develop and demonstrate a methodology for calculation of the time interval between receipt of the containment isolation signals and the first fuel pin failure for loss-of-coolant accidents (LOCAs). Demonstration calculations were performed for a Babcock and Wilcox (B ampersand W) design (Oconee) and a Westinghouse (W) four-loop design (Seabrook). Sensitivity studies were performed to assess the impacts of fuel pin bumup, axial peaking factor, break size, emergency core cooling system availability, and main coolant pump trip on these times. The analysis was performed using the following codes: FRAPCON-2, for the calculation of steady-state fuel behavior; SCDAP/RELAP5/MOD3 and TRACPF1/MOD1, for the calculation of the transient thermal-hydraulic conditions in the reactor system; and FRAP-T6, for the calculation of transient fuel behavior. In addition to the calculation of fuel pin failure timing, this analysis provides a comparison of the predicted results of SCDAP/RELAP5/MOD3 and TRAC-PFL/MOD1 for large-break LOCA analysis. Using SCDAP/RELAP5/MOD3 thermal-hydraulic data, the shortest time intervals calculated between initiation of containment isolation and fuel pin failure are 10.4 seconds and 19.1 seconds for the B ampersand W and W plants, respectively. Using data generated by TRAC-PF1/MOD1, the shortest intervals are 10.3 seconds and 29.1 seconds for the B ampersand W and W plants, respectively. These intervals are for a double-ended, offset-shear, cold leg break, using the technical specification maximum peaking factor and applied to fuel with maximum design bumup. Using peaking factors commensurate widi actual bumups would result in longer intervals for both reactor designs. This document also contains appendices A through J of this report
Performance of a high-resolution CsI(Tl)-PIN readout detector
International Nuclear Information System (INIS)
Kudenko, Yu.G.; Imazato, J.
1992-10-01
A study of a large-volume CsI(Tl) detector with a PIN diode readout was carried out. Our results show a light output of ≤20000 photoelectrons/MeV, an equivalent noise charge (rms) of about 900 electrons, and an equivalent noise level of ≤ 60 keV. We obtained an energy resolution of 11.2% (fwhm) for 1275 keV gamma rays from a 22 Na source. The characteristics of the PIN - preamplifier system as well as the parameters of a small CsI(Tl) - PIN detector with a direct and wavelength shifter readout are also reported. (author)
Thick and large area PIN diodes for hard X-ray astronomy
Ota, N; Sugizaki, M; Kaneda, M; Tamura, T; Ozawa, H; Kamae, T; Makishima, K; Takahashi, T; Tashiro, M; Fukazawa, Y; Kataoka, J; Yamaoka, K; Kubo, S; Tanihata, C; Uchiyama, Y; Matsuzaki, K; Iyomoto, N; Kokubun, M; Nakazawa, T; Kubota, A; Mizuno, T; Matsumoto, Y; Isobe, N; Terada, Y; Sugiho, M; Onishi, T; Kubo, H; Ikeda, H; Nomachi, M; Ohsugi, T; Muramatsu, M; Akahori, H
1999-01-01
Thick and large area PIN diodes for the hard X-ray astronomy in the 10-60 keV range are developed. To cover this energy range in a room temperature and in a low background environment, Si PIN junction diodes of 2 mm in thickness with 2.5 cm sup 2 in effective area were developed, and will be used in the bottom of the Phoswich Hard X-ray Detector (HXD), on-board the ASTRO-E satellite. Problems related to a high purity Si and a thick depletion layer during our development and performance of the PIN diodes are presented in detail.
Directory of Open Access Journals (Sweden)
Ririn Widiyasari
2018-02-01
Full Text Available Tujuan yang ingin dicapai dalam penelitian ini adalah mengetahui faktor apa saja yang mempengaruhi motivasi belajar mahasiswa, apakah terdapat pengaruh yang signifikan antara cara belajar, fasilitas belajar dan lingkungan belajar terhadap motivasi belajar mahasiswa, serta faktor mana yang paling berpengaruh terhadap motivasi belajar mahasiswa. Jumlah sampel dalam penelitian ini adalah 192 mahasiswa (FIP UMJ angkatan tahun 2013-2015 yang aktif mengikuti perkuliahan. Metode penelitian yang dilakukan adalah metode kuantitatif survey. Metode pengambilan data menggunakan kuesioner dengan skala likert. Metode analisis data yang digunakan adalah analisis deskriptif, dan analisis Structural Equation Modeling (SEM berbantuan program LISREL 8.3. Uji hipotesis yang digunakan dalam penelitian ini adalah uji Chi-square dan uji t. Hasil penelitian menunjukkan bahwa variabel cara belajar memiliki kontribusi yang paling besar, selanjutnya variabel kedua yang berkontribusi meningkatkan motivasi belajar adalah lingkungan belajar dan terakhir fasilitas belajar memberikan pengaruh yang paling kecil terhadap motivasi belajar. Jadi, variabel laten cara belajar dan lingkungan belajar berpengaruh positif terhadap motivasi belajar dan fasilitas belajar berpengaruh negatif terhadap motivasi belajar.
Criticality safety studies for plutonium–uranium metal fuel pin fabrication facility
International Nuclear Information System (INIS)
Stephen, Neethu Hanna; Reddy, C.P.
2013-01-01
Highlights: ► Criticality safety limits for PUMP-F facility is identified. ► The fissile mass which can be handled safely during alloy preparation is 10.5 kg. ► The number of fuel slugs which can be handled safely during injection casting is 53. ► The number of fuel slugs which can be handled safely after fuel fabrication is 71. - Abstract: This study focuses on the criticality safety during the fabrication of fast reactor metal fuel pins comprising of the fuel type U–15Pu, U–19Pu and U–19Pu–6Zr in the Plutonium–Uranium Metal fuel Pin fabrication Facility (PUMP-F). Maximum amount of fissile mass which can be handled safely during master alloy preparation, Injection casting and fuel slug preparation following fuel pin fabrication were identified and fixed based on this study. In the induction melting furnace, the fissile mass can be limited to 10.5 kg. During fuel slug preparation and fuel pin fabrication, fuel slugs and pins were arranged in hexagonal and square lattices to identify the most reactive configuration. The number of fuel slugs which can be handled safely after injection casting can be fixed to be 53, whereas after fuel fabrication it is 71
Pin cell discontinuity factors in the transient 3-D discrete ordinates code TORT-TD - 237
International Nuclear Information System (INIS)
Seubert, A.
2010-01-01
This paper describes the application of generalized equivalence theory to the time-dependent 3-D discrete ordinates neutron transport code TORT-TD. The introduction of pin cell discontinuity factors into the discrete ordinates transport equation is described by assuming a linear dependence of the homogenized neutron angular flux within a pin cell which may be discontinuous at the interfaces to adjacent cells. The homogenized flux discontinuity at cell interfaces is expressed by pin cell discontinuity factors which in turn are determined from fuel assembly lattice calculations using HELIOS. Application of TORT-TD to the all rods in state of the PWR MOX/UO 2 Core Transient Benchmark with pin cell homogenized nuclear cross sections demonstrate the potential of pin cell discontinuity factors to reduce pin cell homogenization errors. (authors)
Elementary pinning force for a superconducting vortex
International Nuclear Information System (INIS)
Hyun, O.B.; Finnemore, D.K.; Schwartzkopf, L.; Clem, J.R.
1987-01-01
The elementary pinning force f/sub p/ has been measured for a single vortex trapped in one of the superconducting layers of a cross-strip Josephson junction. At temperatures close to the transition temperature the vortex can be pushed across the junction by a transport current. The vortex is found to move in a small number of discrete steps before it exits the junction. The pinning force for each site is found to be asymmetric and to have a value of about 10/sup -6/ N/m at the reduced temperature, t = T/T/sub c/ = 0.95. As a function of temperature, f/sub p/ is found to vary approximately as (1-t)/sup 3/2/. .AE
Muffly, Matthew; Winegar, Corbett; Miller, Mark Carl; Altman, Gregory
2018-05-03
Using fluoroptic thermography, temperature was measured during pin site drilling of intact cortical human cadaver bone with a combination of one-step drilling, graduated drilling, and one-step drilling with irrigation of 5.0 mm Schanz pins. A 1440 rpm constant force drilling was used to on tibial diaphyses while a sensor probe placed 0.5 mm adjacent to the drill hole measured temperature. Four drilling techniques on each of the tibial segments were performed: 3.5mm drill bit, 5.0mm Schanz pin, 5.0 mm Schanz pin in 3.5 mm pre-drilled entry site, 5.0 mm Schanz pin utilizing irrigation. One-step drilling using a 5.0 mm Schanz pin without irrigation produced a temperature that exceeded the threshold temperature for heat-induced injury in 5 of the 8 trials. With the other three drilling techniques, only one in24 trials produced a temperature that would result in thermal injury. This difference was found to be statistically significant (p = 0.003). The use of irrigation significantly reduced the maximum bone tissue temperature in one-step drilling of a 5.0 mm Schanz pin (p = 0.02). One-step drilling with a 3.5 mm drill bit achieved maximum temperature significantly faster than graduated drilling and drilling with irrigation using a 5.0 mm Schanz pin (p drilling with a 5.0 mm Schanz pin into cortical bone can produce temperatures that can lead to heat-induced injury. Irrigation alone can reduce the temperatures sufficiently to avoid damage. Pre-drilling can increase temperatures significantly but the extent of any injury should be small.
Circuit reliability boosted by soldering pins of disconnect plugs to sockets
Pierce, W. B.
1964-01-01
Where disconnect pins must be used for wiring and testing a circuit, improved system reliability is obtained by making a permanent joint between pins and sockets of the disconnect plug. After the circuit has been tested, contact points may be fused through soldering, brazing, or welding.
Synthesis of yttrium oxide nanoparticles via a facile microplasma-assisted process
Lin, Liangliang; Starostin, Sergey A.; Li, Sirui; Khan, Saif A.; Hessel, Volker
2018-01-01
Plasma electrochemistry is an emerging technique for nanomaterial synthesis. The present study reports the preparation of yttrium oxide nanoparticles via a simple, environmentally benign, microplasma-assisted process operated in pin-to-liquid configuration under ambient atmospheric conditions using
Pin Diode Detector For Radiation Field Monitoring In A Current Mode
International Nuclear Information System (INIS)
Beck, A.; Wengrowicz, U.; Kadmon, Y.; Tirosh, D.; Osovizky, A.; Vulasky, E.; Tal, N.
1999-01-01
Thus paper presents calculations and tests made for a detector based on a bare Pin diode and a Pin diode coupled to a plastic scintillator. These configurations have a variety of applications in radiation field monitoring. For example, the Positron Emission Tomography (PET) technology which becomes an established diagnostic imaging modality. Flour-18 is one of the major isotopes being used by PET imaging. The PET method utilizes short half life β + radioisotopes which, by annihilation, produce a pair of high energy photons (511 keV). Fluoro-deoxyglucose producers are required to meet federal regulations and licensing requirements. Some of the regulations are related to the production in chemistry modules regarding measuring the Start Of Synthesis (SOS) activity and verifying the process repeatability. Locating a radiation detector based on Pin diode inside the chemistry modules is suitable for this purpose. The dimensions of a Pin diode based detector can be small, with expected linearity over several scale decades
Transfixation pinning and casting of radial-ulnar fractures in calves: A review of three cases
St-Jean, Guy; Debowes, Richard M.
1992-01-01
We reviewed the medical records of three calves with radial-ulnar fractures which were reduced and stabilized by transfixation pinning and casting. Multiple Steinmann pins were placed transversely through proximal and distal fracture fragments and the pin ends were incorporated in fiberglass cast material after fracture reduction. Cast material was placed from proximal to distal radius and served as an external frame to maintain pin position and fracture reduction.
Liu, Chen; Lü, Hongliang; Yang, Tong; Zhang, Yuming; Zhang, Yimen; Liu, Dong; Ma, Zhenqiang; Yu, Weijian; Guo, Lixin
2018-06-01
Interfacial and electrical properties were investigated on metal-oxidesemiconductor capacitors (MOSCAPs) fabricated with bilayer ZnO/ZrO2 films by atomic layer deposition (ALD) on p-In0.2Ga0.8As substrates. The ZnO passivated In0.2Ga0.8As MOSCAPs have exhibited significantly improved capacitance-voltage (C-V) characteristics with the suppressed "stretched out" effect, increased accumulation capacitance and reduced accumulation frequency dispersion as well as the lower gate leakage current. In addition, the interface trap density (Dit) estimated by the Terman method was decreased dramatically for ZnO passivated p-In0.2Ga0.8As. The inherent mechanism is attributed to the fact that an ultrathin ZnO IPL employed by ALD prior to ZrO2 dielectric deposition can effectively suppress the formation of defect-related low-k oxides and As-As dimers at the interface, thus effectively improving the interface quality by largely removing the border traps aligned near the valence band edge of the p-In0.2Ga0.8As substrate.
Practical synchronization on complex dynamical networks via optimal pinning control
Li, Kezan; Sun, Weigang; Small, Michael; Fu, Xinchu
2015-07-01
We consider practical synchronization on complex dynamical networks under linear feedback control designed by optimal control theory. The control goal is to minimize global synchronization error and control strength over a given finite time interval, and synchronization error at terminal time. By utilizing the Pontryagin's minimum principle, and based on a general complex dynamical network, we obtain an optimal system to achieve the control goal. The result is verified by performing some numerical simulations on Star networks, Watts-Strogatz networks, and Barabási-Albert networks. Moreover, by combining optimal control and traditional pinning control, we propose an optimal pinning control strategy which depends on the network's topological structure. Obtained results show that optimal pinning control is very effective for synchronization control in real applications.
Fuel Coolant Interaction Results in the Fuel Pins Melting Facility (PMF)
International Nuclear Information System (INIS)
Urunashi, H.; Hirabayashi, T.; Mizuta, H.
1976-01-01
The experimental work related to FCI at PNC has been concentrated into the molten UO 2 dropping test. After the completion of molten UO 2 drop experiments, emphasis is directed toward the FCI phenomena of the initiating conditions of the accident under the more realistic geometry. The experiments are conducted within the Pin Melt Facility (PMF) in which UO 2 pellets clad in stainless steel are melted by direct electric heating under the stagnant or flowing sodium. The primary objectives of the PMF test are to: - obtain detail experimental results (heat-input, clad temperature, sodium temperature, etc.) on the FCI under TOP and LOF conditions; - observe the movement of the fuel before and after the pin failure by the X-ray cinematography; - observe the degree of coherence of the pin failures; - accumulate the experience of the FCI experiment which is applicable to the subassembly or more larger scale; - simulate the fuel behavior of the in-pile test (GETR, CABRI). The preliminary conclusions can be drawn from the foregoing observations are as follows: - Although the fuel motion and FCI of the closed test section appeared to be different from those of the open test section, the conclusion of the effect of the inside pressure on FCI needs more experimental data. - The best heating condition of the UO 2 pellet for the FCI study with PMF is established as 40 w/cm at the steady state and 1680 J/g of UO 2 during the additional transient state. The total energy deposition of the UO 2 pellet is thus estimated in the range of 2400 J/g of UO 2 -2600 J/g of UO 2 . The analytical model of the fuel pin failure and the subsequent FCI are suggested to count the following parameters: - The fuel pin failure due to the fuel vaporization due to the rapid energy deposition; - Molten fuel, clad and sodium interaction in the fuel pin after the pin failure; - The upward flow of molten fuel with molten clad or vapor sodium, as well as the slumping of molten fuel
Venkatesan, P.; Sun, Z.; Sietsma, J.; Yang, Y.
2018-01-01
<p>In this manuscript, we demonstrate a room temperature electrochemical process for efficiently recycling NdFeB magnet waste. First, the magnet waste was completely leached with HCl and then, in-situ electrochemical oxidation was performed to selectively oxidize Fe(II) in the leachate to Fe(III).
ANALISIS IMPOR BERAS DI INDONESIA
Directory of Open Access Journals (Sweden)
Ratih Kumala Sari
2014-10-01
Full Text Available Abstrak ___________________________________________________________________ Salah satu kebijakan pemerintah untuk memenuhi kebutuhan beras yaitu dengan menggenjot produksi beras dalam negeri. Namun dengan semakin meningkatnya jumlah penduduk akan meningkatkan permintaan terhadap beras dan upaya peningkatan produktivitas dalam negeri tidak dapat memenuhi kebutuhan beras dalam negeri. Sehingga untuk menutupi kekurangan tersebut pemerintah mengambil keputusan untuk melakukan impor beras dari negara lain. Akan tetapi pada kenyataannya impor beras dilakukan ketika data statistik menunjukkan bahwa Indonesia sedang mengalami surplus beras. Penelitian ini bertujuan untuk mengetahui faktor-faktor apa saja yang mempengaruhi impor beras di Indonesia. Metode analisis yang digunakan adalah analisis regresi linier berganda dengan model Error Correction Model (ECM. Berdasarkan hasil penelitian disimpulkan bahwa secara parsial maupun secara bersama-sama produksi beras, konsumsi beras, harga beras dalam negeri dan nilai tukar rupiah terhadap dollar AS berpengaruh dan signifikan terhadap impor beras di Indonesia. Abstract ___________________________________________________________________ One of the government’s policy to fulfill the need of rice is to boost the domestic production. However, by increasing the population, the demand of rice will also increase and the effort of increasing the domestic productivity cannot supply domestic rice need. So, to cover the shortage the government make decision to import rice from other countries. Yet, in fact importing rice is occurred when the statistical data showed that the supply of rice in Indonesia is surplus. The purpose of this research is necessary to study the factors which influence the import of rice in Indonesia. The analysis method used is multiple linear regression analysis model with Error Correction Model (ECM. Based on the research proven that partially or jointly the production, the consumption, the
Directory of Open Access Journals (Sweden)
Peter Garlans Sina
2012-10-01
Full Text Available Abstract: Analysis of Economic Literacy. The aim of this research is as an effort to increase economic literacy for individuals and households who want to achieve prosperity. Therefore, the obligation of improving the economic literacy needs to be done in a well-planned manner and come from the strong intention to learn in order to improve the economic literacy. It could have an effect on the assets accumulation, a better debt management, as a protection, as well as to increase savings and managing spending intelligently. Keyword: economic literacy, asset, debt, protection, saving, spending Abstrak: Analisis Literasi Ekonomi. Tulisan ini bertujuan sebagai upaya meningkatkan literasi ekonomi bagi individu maupun rumah tangga yang menginginkan mencapai kesejahteraan. Oleh karena itu, kewajiban meningkatkan literasi ekonomi perlu dilakukan secara terencana dan diawali dari niat untuk belajar meningkatkan literasi ekonomi karena dapat berefek pada akumulasi aset, pengelolaan utang yang tepat, proteksi, meningkatkan tabungan dan cerdas mengelola pengeluaran. Kata kunci: literasi ekonomi, aset, utang, proteksi, menabung, pengeluaran
Critical currents and superconductivity ferromagnetism coexistence in high-Tc oxides
Khene, Samir
2016-01-01
The book comprises six chapters which deal with the critical currents and the ferromagnetism-superconductivity coexistence in high-Tc oxides. It begins by gathering key data for superconducting state and the fundamental properties of the conventional superconductors, followed by a recap of the basic theories of superconductivity. It then discusses the differences introduced by the structural anisotropy on the Ginzburg-Landau approach and the Lawrence-Doniach model before addressing the dynamics of vortices and the ferromagnetism-superconductivity coexistence in high-Tc oxides, and provides an outline of the pinning phenomena of vortices in these materials, in particular the pinning of vortices by the spins. It elucidates the methods to improve the properties of superconducting materials for industrial applications. This optimization aims at obtaining critical temperatures and densities of critical currents at the maximum level possible. Whereas the primary objective is the basic mechanisms pushing the superco...
Self-assembling nano-diameter needlelike pinning centers in YBCO, utilizing a foreign element dopant
Energy Technology Data Exchange (ETDEWEB)
Sawh, Ravi-Persad [Texas Center for Superconductivity and Physics Department, University of Houston, 632 Science and Research Bldg 1, Houston Texas 77204-5005 (United States); Weinstein, Roy [Texas Center for Superconductivity and Physics Department, University of Houston, 632 Science and Research Bldg 1, Houston Texas 77204-5005 (United States); Obot, Victor [Department of Mathematics, Texas Southern University, 3100 Cleburne St, Houston Texas 77004-4597 (United States); Parks, Drew [Texas Center for Superconductivity and Physics Department, University of Houston, 632 Science and Research Bldg 1, Houston Texas 77204-5005 (United States); Gandini, Alberto [Texas Center for Superconductivity and Physics Department, University of Houston, 632 Science and Research Bldg 1, Houston Texas 77204-5005 (United States); Skorpenske, Harley [Texas Center for Superconductivity and Physics Department, University of Houston, 632 Science and Research Bldg 1, Houston Texas 77204-5005 (United States)
2006-06-01
Although pinning centers created by irradiation presently produce the highest J{sub c}, it is probable that ultimately these will be emulated by chemical pinning centers. The best pinning centers produced by irradiation nevertheless provide guidelines for desirable morphology of chemical pinning structures. The highest J{sub c} produced earlier in textured HTS was obtained using isotropic high-energy ions produced by fission of {sup 235}U. This so-called U/n process produces pinning centers of diameter {<=} 4.5 nm, with an effective length of {approx}2.7 {mu}m. Maximum J{sub c} occurs for pinning center density of {approx}10{sup 10} cm{sup -3}. We use this as a model for desired chemical pinning centers. Our approach to introducing chemical pinning centers has been to produce precipitates within the HTS containing elements not native to the HTS, and to seek needlelike (columnar) deposits of small diameter. We report here on the formation of needlelike or columnar deposits in textured Y123 containing a dopant foreign to Y123. It serves as a demonstration that self-assembling nanometer diameter columns utilizing a dopant foreign to the HTS system are a feasible goal. These deposits, however, do not fully meet the ultimate requirements of pinning centers because the desired deposits should be smaller. The self-assembling columns formed contain titanium, are {approx}500 nm in diameter, and up to 10 {mu}m long. The size and morphology of the deposits vary with the mass of admixed Ti dopant. J{sub c} is decreased for small dopant mass. At larger dopant masses needlelike precipitates form, and J{sub c} increases again. A small range of mass of admixed Ti exists in which J{sub c} is enhanced by pinning. In the range of admixed Ti mass studied in these experiments there is a negligible effect on T{sub c}. Magnetization studies of J{sub c} are also reported.
Directory of Open Access Journals (Sweden)
Luluk Kristianingsih
2013-09-01
Full Text Available Pembangkit listrik tenaga uap (PLTU merupakan pembangkit listrik yang banyak digunakan di Indonesia. Salah satu bagian dari sistem PLTU yang memiliki risiko bahaya tinggi adalah boiler, oleh karena itu diperlukan adanya analisis bahaya dan safety system sebagai langkah pencegahan bahaya pada boiler. Analisis bahaya dalam penelitian ini dilakukan menggunakan metode HAZOP. Node yang dipakai adalah economizer, steam drum, superheater, dan reheater yang merupakan komponen utama penyusun boiler. Guide word dan deviasi ditentukan berdasarkan control chart yang dibentuk oleh data proses masing-masing komponen selama bulan Maret 2013. Estimasi likelihood dilakukan berdasarkan data maintenance dari work order PT YTL selama 5 tahun, sedangkan estimasi consequences dilakukan berdasarkan kriteria risiko yang ditimbulkan serta berdasarkan control chart. Hasil perkalian likelihood dan consequences dengan risk matrix menghasilkan kriteria risiko dari komponen. Berdasarkan hasil analisis, diperoleh hasil bahwa komponen yang memiliki risiko bahaya paling besar adalah level transmitter steam drum dengan deviasi berupa less level, yaitu dengan kriteria likelihood adalah A dan consequences 4, sehingga risiko bernilai extreme. Selain itu, risiko extreme juga terdapat pada pressure transmitter outlet superheater, dengan likelihood B dan consequences 4. Untuk menurunkan risiko, maka dilakukan perawatan dan kalibrasi secara rutin, serta penambahan redundant transmitter. Bahaya paling besar pada seluruh node adalah adanya kebakaran. Oleh karena itu, dilakukan analisis emergency response plan untuk kebakaran yang mencakup peta evakuasi, tugas dan tanggungjawab tiap personel, langkah pencegahan, serta langkah penanganan.
International Nuclear Information System (INIS)
Toebbe, H.
1987-10-01
The report describes the status of experience with respect to the abrasion behavior of bundles in standard fuel elements and test elements with wire or grid spacing in the reactors Rapsodie fortissimo, Phenix, DFR, PFR, EBR-II, FFTF, JOYO and KNK II. With the help of simple considerations concerning thermoelastic pin-pin interactions a figure of merit is deduced from the different bundle parameters, which allows a comparative judgement of the parameters of different bundle concepts [de
Shield requirement estimation for pin storage room in fuel fabrication plant
International Nuclear Information System (INIS)
Shanthi, M.M.; Keshavamurthy, R.S.; Sivashankaran, G.
2012-01-01
Fast Reactor Fuel Cycle Facility (FRFCF) is an upcoming project in Kalpakkam. It has the facility to recycle the fuel from PFBR. It is an integrated facility, consists of fuel reprocessing plant, fuel fabrication plant (FFP), core subassembly plant, Reprocessed Uranium plant (RUP) and waste management plant. The spent fuel from PFBR would be reprocessed in fuel reprocessing plant. The reprocessed fuel material would be sent to fuel fabrication plant. The main activity of fuel fabrication plant is the production of MOX fuel pins. The fuel fabrication plant has a fuel pin storage room. The shield requirement for the pin storage room has been estimated by Monte Carlo method. (author)
Experimental study of flow friction characteristics of integral pin-fin tubes
International Nuclear Information System (INIS)
Ding Ming; Yan Changqi; Sun Licheng
2007-01-01
Friction characteristics of integral pin-fin tubes, through which lubricating-oil flowed vertically, were studied experimentally. Effects of the pitch, the height of fins and the machining direction on friction coefficient were analyzed. The experimental results showed that the friction coefficient of the integral pin-fro tube was obviously lager than that of smooth tube. Compared with other influential factors, the effect of the height of fins was dominant. Because the three-dimensional pin fin could disturb and destroy the boundary layer, when the Reynolds Number reached 200-300, the friction coefficient curve began to bend, that was, a turning point was appeared in the friction coefficient curve. (authors)
Pinning synchronization of memristor-based neural networks with time-varying delays.
Yang, Zhanyu; Luo, Biao; Liu, Derong; Li, Yueheng
2017-09-01
In this paper, the synchronization of memristor-based neural networks with time-varying delays via pinning control is investigated. A novel pinning method is introduced to synchronize two memristor-based neural networks which denote drive system and response system, respectively. The dynamics are studied by theories of differential inclusions and nonsmooth analysis. In addition, some sufficient conditions are derived to guarantee asymptotic synchronization and exponential synchronization of memristor-based neural networks via the presented pinning control. Furthermore, some improvements about the proposed control method are also discussed in this paper. Finally, the effectiveness of the obtained results is demonstrated by numerical simulations. Copyright © 2017 Elsevier Ltd. All rights reserved.
Run-beyond-clad-breach oxide testing in EBR-2
International Nuclear Information System (INIS)
Lambert, J.D.B.; Bottcher, J.H.; Strain, R.V.; Gross, K.C.; Lee, M.J.; Webb, J.P.; Colburn, R.P.; Ukai, S.; Nomura, S.; Odo, T.; Shikakura, S.
1990-01-01
Fourteen tests sponsored by the US and Japan were used to study reliability of breached LMR oxide fuel pins during continued operation in EBR-II for a range of conditions and parameters. The fuel-sodium reaction product governed pin behavior. It extended primary breaches by swelling and promoted secondary failures, yet it inhibited loss of fuel and fission products and enhanced release of delayed neutrons used in monitoring breach condition. Fission gas and cesium, the main contaminants from failures, could be adequately controlled. This positive EBR-II experience suggested that limited operation with failed fuel may be feasible in commercial LMR's. 16 refs., 14 figs., 4 tabs
Vortex lattices in different configurations of periodic pinning line-arrays
International Nuclear Information System (INIS)
Lima, Clessio Leao S.; Cabral, Leonardo R.E.; Souza Silva, Clecio C. de; Aguiar, J. Albino
2006-01-01
The vortex lattice (VL) ground-state configurations are found using Monte Carlo (MC) simulated annealing with a local molecular dynamics (MD) in the London limit. We study the field dependence of the melting temperature for commensurate and incommensurate vortex lattices interacting with different periodic arrays of pinning. We also investigated the proliferation of topological defects and its dependence on the periodic pinning array symmetry and temperature
How pinning and contact angle hysteresis govern quasi-static liquid drop transfer.
Chen, H; Tang, T; Zhao, H; Law, K-Y; Amirfazli, A
2016-02-21
This paper presents both experimental and numerical simulations of liquid transfer between two solid surfaces with contact angle hysteresis (CAH). Systematic studies on the role of the advancing contact angle (θa), receding contact angle (θr) and CAH in determining the transfer ratio (volume of the liquid transferred onto the acceptor surface over the total liquid volume) and the maximum adhesion force (Fmax) were performed. The transfer ratio was found to be governed by contact line pinning at the end of the transfer process caused by CAH of surfaces. A map based on θr of the two surfaces was generated to identify the three regimes for liquid transfer: (I) contact line pinning occurs only on the donor surface, (II) contact line pinning occurs on both surfaces, and (III) contact line pinning occurs only on the acceptor surface. With this map, an empirical equation is provided which is able to estimate the transfer ratio by only knowing θr of the two surfaces. The value of Fmax is found to be strongly influenced by the contact line pinning in the early stretching stage. For symmetric liquid bridges between two identical surfaces, Fmax may be determined only by θa, only by θr, or by both θa and θr, depending on the magnitude of the contact angles. For asymmetric bridges, Fmax is found to be affected by the period when contact lines are pinned on both surfaces.
Effect of shoulder to pin ratio on magnesium alloy Friction Stir Welding
Othman, N. H.; Ishak, M.; Shah, L. H.
2017-09-01
This study focuses on the effect of shoulder to pin diameter ratio on friction stir welding of magnesium alloy AZ31. Two pieces of AZ31 alloy with thickness of 2 mm were friction stir welded by using conventional milling machine. The shoulder to pin diameter ratio used in this experiment are 2.25, 2.5, 2.75, 3, 3.33, 3.66, 4.5, 5 and 5.5. The rotational speed and welding speed used in this study are 1000 rpm and 100 mm/min, respectively. Microstructure observation of welded area was studied by using optical microscope. Equiaxed grains were observed at the TMAZ and stir zone indicating fully plastic deformation. The grain size of stir zone increased with decreasing shoulder to pin ratio from ratio 3.33 to 5.5 due to higher heat input. It is observed that, surface galling and faying surface defect is produced when excessive heat input is applied. To evaluate the mechanical properties of this specimen, tensile test was used in this study. Shoulder to pin ratio 5.5 shows lowest tensile strength while shoulder to pin diameter ratio 3.33 shows highest tensile strength with weld efficiency 91 % from based metal.
Further developments in NbTi superconductors with artificial pinning centers
International Nuclear Information System (INIS)
Kanithi, H.C.; Valaris, P.; Motowidlo, L.R.; Zeitlin, B.A.; Scanlan, R.M.
1992-01-01
Artificial pinning centers (APC) have been successfully incorporated in multifilamentary NbTi based superconductors. using pure niobium as the pinning material and applying state-of-the-art processing technology, we have developed conductors which exhibit record low-field current densities. Two volume fractions of Nb have been investigated. One of the objectives of the present development effort is the feasibility study of billet scale-up from earlier work. A J 3 (3T) of ∼7500 A/mm 2 , which is twice that of the present MRI conductors, and a J c (5T) of ∼3400 A/mm 2 , have been achieved in samples. The results of this ongoing effort, in terms of conductor configuration, microstructure, critical current density, and pinning force, are presented in this paper. Appropriate comparisons with past performances are made
Control of Flux Pinning in MOD YBCO Coated Conductor
Energy Technology Data Exchange (ETDEWEB)
Zhang, W. [American Superconductor Corporation, Westborough, MA; Huang, Y. [American Superconductor Corporation, Westborough, MA; Li, X. [American Superconductor Corporation, Westborough, MA; Kodenkandath, Thomas [American Superconductor Corporation, Westborough, MA; Rupich, Marty [American Superconductor Corporation, Westborough, MA; Schoop, U. [American Superconductor Corporation, Westborough, MA; Verebelyi, D. T. [American Superconductor Corporation, Westborough, MA; Thieme, C. L. H. [American Superconductor Corporation, Westborough, MA; Siegal, E. E. [American Superconductor Corporation, Westborough, MA; Holesinger, T. G. [Los Alamos National Laboratory (LANL); Maiorov, B. [Los Alamos National Laboratory (LANL); Miller, D. J. [Argonne National Laboratory (ANL); Maroni, V. A. [Argonne National Laboratory (ANL); Goyal, Amit [ORNL; Specht, Eliot D [ORNL; Paranthaman, Mariappan Parans [ORNL
2007-01-01
Two different types of defect structures have been identified to be responsible for the enhanced pinning in metal organic deposited YBCO films. Rare earth additions result in the formation of nanodots in the YBCO matrix, which form uncorrelated pinning centers, increasing pinning in all magnetic field orientations. 124-type intergrowths, which form as laminar structures parallel to the ab-plane, are responsible for the large current enhancement when the magnetic field is oriented in the ab-plane. TEM studies showed that the intergrowths emanate from cuprous containing secondary phase particles, whose density is partially controlled by the rare earth doping level. Critical process parameters have been identified to control this phase formation, and therefore, control the f 24 intergrowth formation. This work has shown that through process control and proper conductor design, either by adjusting the composition or by multiple coatings of different functional layers, the desired angular dependence can be achieved.
Control of flux pinning in MOD YBCO coated conductor.
Energy Technology Data Exchange (ETDEWEB)
Zhang, W.; Huang, Y.; Li, X.; Kodenkandath, T.; Rupich, M. W.; Schoop, U.; Verebelyi, D. T.; Thieme, C. L. H.; Siegal, E.; Holesinger, T. G.; Maiorov, B.; Civale, L.; Miller, D. J.; Maroni, V. A.; Li, J.; Martin, P. M.; Specht, E. D.; Goyal, A.; Paranthaman, M. P.; American Superconductor Corp.; LANL; ORNL
2007-06-01
NTwo different types of defect structures have been identified to be responsible for the enhanced pinning in metal organic deposited YBCO films. Rare earth additions result in the formation of nanodots in the YBCO matrix, which form uncorrelated pinning centers, increasing pinning in all magnetic field orientations. 124-type intergrowths, which form as laminar structures parallel to the ab-plane, are responsible for the large current enhancement when the magnetic field is oriented in the ab-plane. TEM studies showed that the intergrowths emanate from cuprous containing secondary phase particles, whose density is partially controlled by the rare earth doping level. Critical process parameters have been identified to control this phase formation, and therefore, control the f 24 intergrowth formation. This work has shown that through process control and proper conductor design, either by adjusting the composition or by multiple coatings of different functional layers, the desired angular dependence can be achieved.
Component Pin Recognition Using Algorithms Based on Machine Learning
Xiao, Yang; Hu, Hong; Liu, Ze; Xu, Jiangchang
2018-04-01
The purpose of machine vision for a plug-in machine is to improve the machine’s stability and accuracy, and recognition of the component pin is an important part of the vision. This paper focuses on component pin recognition using three different techniques. The first technique involves traditional image processing using the core algorithm for binary large object (BLOB) analysis. The second technique uses the histogram of oriented gradients (HOG), to experimentally compare the effect of the support vector machine (SVM) and the adaptive boosting machine (AdaBoost) learning meta-algorithm classifiers. The third technique is the use of an in-depth learning method known as convolution neural network (CNN), which involves identifying the pin by comparing a sample to its training. The main purpose of the research presented in this paper is to increase the knowledge of learning methods used in the plug-in machine industry in order to achieve better results.
Integrated quality status and inventory tracking system for FFTF driver fuel pins
International Nuclear Information System (INIS)
Gottschalk, G.P.
1979-11-01
An integrated system for quality status and inventory tracking of Fast Flux Test Facility (FFTF) driver fuel pins has been developed. Automated fuel pin identification systems, a distributed computer network, and a data base are used to implement the tracking system
Directory of Open Access Journals (Sweden)
Hirokazu Tanaka
2013-05-01
Full Text Available PIN-FORMED (PIN proteins localize asymmetrically at the plasma membrane and mediate intercellular polar transport of the plant hormone auxin that is crucial for a multitude of developmental processes in plants. PIN localization is under extensive control by environmental or developmental cues, but mechanisms regulating PIN localization are not fully understood. Here we show that early endosomal components ARF GEF BEN1 and newly identified Sec1/Munc18 family protein BEN2 are involved in distinct steps of early endosomal trafficking. BEN1 and BEN2 are collectively required for polar PIN localization, for their dynamic repolarization, and consequently for auxin activity gradient formation and auxin-related developmental processes including embryonic patterning, organogenesis, and vasculature venation patterning. These results show that early endosomal trafficking is crucial for cell polarity and auxin-dependent regulation of plant architecture.
Directory of Open Access Journals (Sweden)
O. Di Bartolomeo
2008-07-01
Full Text Available Le osservazioni al microscopio elettronico a scansione (SEM delle superfici di frattura ottenute a seguito di rotture per fatica consentono di evidenziare alcuni meccanismi di avanzamento che dipendono dal materiale e dalla modalità di applicazione delle sollecitazioni. L’introduzione di moderne tecniche di analisi di immagine assistite al calcolatore permette di elaborare un numero di informazioni elevato che consente di porre in relazione le caratteristiche morfologiche locali con il comportamento meccanico macroscopico del materiale.In questo lavoro è stata implementata una tecnica innovativa di analisi di immagine basata sull’analisi della tessitura, valutando l’influenza delle condizioni di applicazione della sollecitazione (ΔK applicato sulla evoluzione del clivaggio rilevato sulle superfici di frattura a fatica di una ghisa sferoidale ferrito-perlitica.
Modeling the instability behavior of thin film devices: Fermi Level Pinning
Moeini, Iman; Ahmadpour, Mohammad; Gorji, Nima E.
2018-05-01
We investigate the underlying physics of degradation/recovery of a metal/n-CdTe Schottcky junction under reverse or forward bias stressing conditions. We used Sah-Noyce-Shockley (SNS) theory to investigate if the swept of Fermi level pinning at different levels (under forward/reverse bias) is the origin of change in current-voltage characteristics of the device. This theory is based on Shockley-Read-Hall recombination within the depletion width and takes into account the interface defect levels. Fermi Level Pinning theory was primarily introduced by Ponpon and developed to thin film solar cells by Dharmadasa's group in Sheffield University-UK. The theory suggests that Fermi level pinning at multiple levels occurs due to high concentration of electron-traps or acceptor-like defects at the interface of a Schottky or pn junction and this re-arranges the recombination rate and charage collection. Shift of these levels under stress conditions determines the change in current-voltage characteristics of the cell. This theory was suggested for several device such as metal/n-CdTe, CdS/CdTe, CIGS/CdS or even GaAs solar cells without a modeling approach to clearly explain it's physics. We have applied the strong SNS modeling approach to shed light on Fermi Level Pinning theory. The modeling confirms that change in position of Fermi Level and it's pining in a lower level close to Valence band increases the recombination and reduces the open-circuit voltage. In contrast, Fermi Level pinning close to conduction band strengthens the electric field at the junction which amplifies the carrier collection and boosts the open-circuit voltage. This theory can well explain the stress effect on device characteristics of various solar cells or Schottky junctions by simply finding the right Fermi level pinning position at every specific stress condition.
Ding, R. Jeffrey; Oelgoetz, Peter A.
1999-01-01
The "Auto-Adjustable Pin Tool for Friction Stir Welding", was developed at The Marshall Space Flight Center to address process deficiencies unique to the FSW process. The auto-adjustable pin tool, also called the retractable pin-tool (R.PT) automatically withdraws the welding probe of the pin-tool into the pin-tool's shoulder. The primary function of the auto-adjustable pin-tool is to allow for keyhole closeout, necessary for circumferential welding and localized weld repair, and, automated pin-length adjustment for the welding of tapered material thickness. An overview of the RPT hardware is presented. The paper follows with studies conducted using the RPT. The RPT was used to simulate two capabilities; welding tapered material thickness and closing out the keyhole in a circumferential weld. The retracted pin-tool regions in aluminum- lithium 2195 friction stir weldments were studied through mechanical property testing and metallurgical sectioning. Correlation's can be =de between retractable pin-tool programmed parameters, process parameters, microstructure, and resulting weld quality.
Analisis Rugi Daya Pada Penyulang Bangli Dengan Beroperasinya PLTS Kayubihi
Directory of Open Access Journals (Sweden)
I GN Dion Adiputra
2015-06-01
Full Text Available Analisis rugi daya pada Penyulang Bangli dilakukan untuk mengetahui perbanding an rugi daya pada jaringan distribusi setelah penempatan pembangkit tersebar jenis PLTS berkapasitas 1 MWp. Lokasi penempatan PLTS ditentukan berdasarkan analisis sensitivitas bus. Nilai sensitivitas bus(?didapat dengan cara membandingkan nilai rugi daya pada sistem dengan total beban yang terhubung pada bus. Penelitian ini menggunakan simulasi aliran daya dengan metode aliran daya Newton-Raphson. Hasil penelitian menunjukkan bus TK 0041 memiliki sensitivitas terbesar dengan nilai ?= 0,178. Dari hasil simulasi aliran daya, penempatan PLTS 1MWp pada lokasi alternatif 1 menghasilkan rugi daya minimum pada Penyulang Bangli yaitu 103,1 kW atau 3,3% dari total suplai daya 3071 kW. Pemasangan PLTS dapat menurunkan rugi daya pada Penyulang Bangli sebesar 57 kW dari total rugi daya pada kondisi tanpa PLTS yaitu 160,1 kW. Bila dibandingkan dengan kondisi eksisting, penem patan PLTS pada lokasi alternatif 1 memiliki selisih rugi daya 7,3 kW lebih kecil dari total rugi daya yang dihasilkan kondisi eksisting sebesar 110,4kW.
International Nuclear Information System (INIS)
Tanaka, Kosuke; Kikuchi, Shin; Katsuyama, Kozo; Nagamine, Tsuyoshi; Mitsugi, Takeshi; Uto, Manabu; Tatebe, Kazuaki; Onose, Shoji; Maruyama, Tadashi
1998-10-01
This paper describes the results of postirradiation examination and analysis by CORAL code for irradiation performance of CRM601 control rod, which was the 6th reloaded control rod with shroud type absorber pins for use in JOYO MK-II core. The detailed visual examination indicated that there was no cladding breach in absorber pins. However, sodium ingress from the vent tube was observed in four absorber pins among seven pins. While a remarkable oval deformation occurred in cladding tube of helium bonded absorber pins, a little or no diametral change was observed in the absorber pins in which sodium ingress took place. From metallurgical observations and the analysis by CORAL code, it was estimated that the shroud tube installed in helium bonded absorber pins were irradiated at 720degC, and those in sodium bonded absorber pins were irradiated at 420degC. It was confirmed that diametral change of cladding depended on the initial gap between shroud and cladding tube. The results of present investigation indicate that it is desirable to use the materials with low thermal expansion coefficient for shroud tubes, and that sodium bonded absorber pins were advantageous for obtaining long life control rods. (author)
Directory of Open Access Journals (Sweden)
Ariel Bagus Nugroho
2015-11-01
Full Text Available RSUD Tugurejo Semarang merupakan Rumah Sakit kelas B milik pemerintah Provinsi Jawa Tengah yang menyediakan pelayanan jasa untuk masyarakat. Dalam manajemen pengolahan data, RSUD Tugurejo Semarang telah menggunakan sistem informasi rumah sakit. Untuk mengetahui apakah sistem informasi telah berjalan seperti yang diharapkan, maka perlu dilakukan analisis tatakelola teknologi informasi. Pada penelitian ini analisis tatakelola teknologi informasi berfokus pada proses pengawasan, evaluasi dan penilaian kinerja, dan kesesuaian kinerja teknologi informasi, yaitu domain MEA01 pada framework COBIT 5.Tujuan penelitian ini untuk mengetahui tingkat kapabilitas dan strategi perbaikan untuk proses pengawasan, evaluasi dan penilaian kinerja dan kesesuaian TI. Metode pengumpulan data penelitian ini dengan menggunakan studi dokumen, kuesioner dan wawancara kemudian dianalisis tingkat kapabilitas dan kesenjangan. Tingkat kapabilitas yang didapat dari hasil penelitian yaitu berada level 2 (managed. Untuk menaikkan tingkat kapabilitas pada level 3 maka maka perlu dilakukan secara bertahap strategi perbaikan pada PA 2.1, PA2.2, PA 3.1, dan 3.2. Kata kunci: Analisis Tata Kelola TI, COBIT 5, MEA01, Tingkat Kapabilitas, Rumah Sakit.
Pinning in nonmagnetic borocarbides
International Nuclear Information System (INIS)
Zholobenko, A.N.; Mikitik, G.P.; Fil, V.D.; Kim, J.D.; Lee, S.I.
2005-01-01
The field dependences of the Labush parameter in nonmagnetic borocarbides are measured by the method which does not require the free flux flow regime. The anticipated critical current densities are estimated. These values are by two orders of magnitude higher than those measured 'directly' in transport (magnetic) experiments. The giant peak-effect in the field dependences of the Labush parameter is revealed in the Y-based borocarbides. Its behavior is well approximated by the collective pinning theory
Assessment of clad integrity of PHWR fuel pin following a postulated severe accident
International Nuclear Information System (INIS)
Dutta, B.K.; Kushwaha, H.S.; Venkat Raj, V.
2000-01-01
A mechanistic fuel performance analysis code FAIR has been developed. The code can analyse fuel pins with free standing as well as collapsible clad under normal, off-normal and accident conditions of reactors. The code FAIR is capable of analysing the effects of high burnup on fuel behaviour. The code incorporates finite element based thermo-mechanical module for computing transient temperature distribution and thermal-elastic-plastic stresses in the fuel pin. A number of high temperature thermo-physical and thermo-mechanical models also have been incorporated for analysing fuel pins subjected to severe accident scenario. The present paper describes salient features of code FAIR and assessment of clad integrity of PHWR fuel pins with different initial burnup subjected to severe accident scenario. (author)
Fracture repair with transfixation pins and fiberglass cast in llamas and small ruminants.
Kaneps, A J; Schmotzer, W B; Huber, M J; Riebold, T W; Watrous, B J; Arnold, J S
1989-11-01
Transfixation pinning with fiberglass casting is an effective and adaptable method of longbone fracture fixation in llamas and small ruminants. Treatment of fractures in 7 limbs of 4 llamas and 2 small ruminants with this technique are described. Steinmann pins are placed transcortically proximal, and if necessary, distal to the fracture. The pin ends and limb are encased in fiberglass cast material. The cast is strong enough in animals of this size to eliminate the need for external frames or connecting bars. Severely comminuted fractures and fractures near joints are especially suited to fixation with this technique. Complications encountered in these cases included loosening of pins and one delayed union. All fractures healed to permit full use of the limb.
van der Borden, Arnout J; Maathuis, Patrick G M; Engels, Eefje; Rakhorst, Gerhard; van der Mei, Henny C; Busscher, Henk J; Sharma, Prashant Kumar
2007-04-01
Pin tract infections of external fixators used in orthopaedic reconstructive bone surgery are serious complications that can eventually lead to periostitis and osteomyelitis. In vitro experiments have demonstrated that bacteria adhering to stainless steel in a biofilm mode of growth detach under the influence of small electric currents, while remaining bacteria become less viable upon current application. Therefore, we have investigated whether a 100microA electric current can prevent signs of clinical infection around percutaneous pins, implanted in the tibia of goats. Three pins were inserted into the lateral right tibia of nine goats, of which one served for additional frame support. Two pins were infected with a Staphylococcus epidermidis strain of which one pin was subjected to electric current, while the other pin was used as control. Pin sites were examined daily. The wound electrical resistance decreased with worsening of the infection from a dry condition to a purulent stage. After 21 days, animals were sacrificed and the pins taken out. Infection developed in 89% of the control pin sites, whereas only 11% of the pin sites in the current group showed infection. These results show that infection of percutaneous pin sites of external fixators in reconstructive bone surgery can be prevented by the application of a small DC electric current.
Self-designed femoral neck guide pin locator for femoral neck fractures.
Xia, Shengli; Wang, Ziping; Wang, Minghui; Wu, Zuming; Wang, Xiuhui
2014-01-01
Closed reduction and fixation with 3 cannulated screws is a widely accepted surgery for the treatment of femoral neck fractures. However, how to obtain optimal screw placement remains unclear. In the current study, the authors designed a guide pin positioning system for femoral neck fracture cannulated screw fixation and examined its application value by comparing it with freehand guide needle positioning and with general guide pin locator positioning provided by equipment manufacturers. The screw reset rate, screw parallelism, triangle area formed by the link line of the entry point of 3 guide pins, and maximum vertical load bearing of the femoral neck after internal fixation were recorded. As expected, the triangle area was largest in the self-designed positioning group, followed by the general positioning group and the freehand positioning group. The difference among the 3 groups was statistically significant (P.05). The authors’ self-designed guide pin positioning system has the potential to accurately insert cannulated screws in femoral neck fractures and may reduce bone loss and unnecessary radiation.
Primary water stress corrosion cracking resistance of alloy X-750 for guide tube support pins
International Nuclear Information System (INIS)
Yonezawa, T.; Onimura, K.; Yonehana, M.; Fujitani, T.
1990-01-01
The authors have developed the maintenance free guide tube support pins for PWR, and conducted the three kinds of long time stress corrosion cracking tests in high temperature water, in order to verify the reliability of the maintenance free guide tube support pins. This paper describes the features of our maintenance free support pins and the results of long time stress corrosion cracking test for the maintenance free support pins. After exposure at 320 0 C in the simulated primary water of PWR for about 35,000 hours or at 360 0 C in the same chemistry water as the primary water for about 24,900 hours, no abnormal indication such as cracks was observed in all test support pins exposed 320 0 C and 360 0 C primary water, by ultrasonic inspection, and liquid penetrate test. From the above, it seems that our maintenance free support pins are keepable the soundness up to the end of plant life, in PWR plants
International Nuclear Information System (INIS)
Coquerelle, M.; Walker, C.T.; Whitlow, W.H.
1980-01-01
The experiment MOL 7B was carried out in a epithermal flux in the Belgian reactor BR2. The pin examined contained fuel of initial composition (Usub(0.7)Pusub(0.3))Osub(1.98). It had been irradiated to a maximum burn-up of 13.2 at% at a maximum linear power of 568Wcm -1 . The fuel was clad with coldworked stainless steel. Electron microprobe analysis indicated that a Cr 2 O 3 type oxide was the main constituent of the grey phases in the gap. A metallic phase on the fuel surface had apparently resulted from the mechanical compaction of fragments of cladding that had been depleted in chromium by oxidation. Thus the main components of the phase were iron and nickel. Chromium loss from the inner cladding surface was significant only in the upper regions of the pin. In pin sections that were metallographically examined sigma phase and carbides of the type M 23 C 6 were present at the grain boundaries of the cladding. Cladding corrosion was not an Arrhenius function of the cladding temperature: the amount of metal lost from the inner cladding surface decreased with rise in cladding temperature above 910 K. A contributor to metal loss was the mechanical detachment of fragments of cladding which reformed as a metallic layer on the surface of the fuel. Chromium depletion and sigma phase formation at grain boundaries lowered the cohesive forces between grains which were then mechanically detached. Chromium loss from grain boundaries is mainly the results of oxidation of the cladding by the mixed oxide fuel. Data are presented to support the view that the local average O/M of the fuel determined the rate of oxidation and consequently the extent of chromium depletion. Fuel-cladding mechanical interactions were weak in the upper regions of the pin where metal loss was small
Syaifullah, M. Djazim
2018-01-01
IntisariKondisi curah hujan di wilayah Jakarta pada kejadian banjir besar tanggal 17 Januari 2013 telah dianalisis yang dihubungkan dengan kondisi atmosfer pada selang waktu tersebut. Data curah hujan menggunakan data TRMM sedangkan analisis kondisi atmosfer menggunakan data rawinsonde. Hasil analisis menunjukkan bahwa puncak kejadian banjir Jakarta musim hujan tahun 2013 terjadi pada tanggal 17 Januari 2013 disebabkan oleh faktor lokal yang sangat kuat ditambah dengan faktor global yang mend...
Analisis Sikap Konsumen terhadap Produk Fashion Lokal dan Impor
Setiawan, Evelyn
2014-01-01
Abstrak: Analisis Sikap Konsumen Terhadap Produk Fashion Lokal dan Impor. Penelitian ini bertujuan untuk menganalisis sikap konsumen terhadap produk fashion lokal dan impor yang akan berpengaruh terhadap keputusan konsumsi. Sampel yang akan digunakan dalam penelitian ini adalah 1.000 mahasiswa dari 10 perguruan tinggi swasta terbesar di Surabaya. Pengambilan data dilakukan dengan metode kuesioner. Hasil pengujian statistik menunjukkan bahwa sebagian besar mahasiswa di Surabaya merasa bangga d...
Uso de Analisis de Covarianza (ANCOVA en investigacion cientifica.
Directory of Open Access Journals (Sweden)
Badii, M.H.
2008-01-01
Full Text Available The basics of the ANalisis of COVAriance (ANCOVA are given. The objectives and the application of ANCOVA are laid out. Techniques for the estimation of contrasts and for the control and reduction of the degree of error are discussed. The application of a simple ANCOVA using real data is highlighted. The application of this technique in fixing the auxiliary variable in experimentation is emphasized.
International Nuclear Information System (INIS)
Jha, Alok K; Matsumoto, Kaname; Horide, Tomoya; Saini, Shrikant; Mele, Paolo; Ichinose, Ataru; Yoshida, Yutaka; Awaji, Satoshi
2015-01-01
The effect of hybrid (columnar and spherical together) artificial pinning centers (APCs) on the vortex pinning properties of YBa 2 Cu 3 O 7−δ (YBCO) thin films is investigated in detail on the basis of variation of critical current density (J C ) with applied magnetic field and also with the orientation of the applied magnetic field at 65 K and 77 K. Premixed YBCO + BaSnO 3 composite targets are used for the deposition of the YBCO films which consist of self-assembled BaSnO 3 nanocolumns (1D APCs); on the other hand, for the deposition of the YBCO films with hybrid APCs (BaSnO 3 nanocolumns together with Y 2 O 3 nanoparticles), the surface of the premixed YBCO + BaSnO 3 composite targets are modified by putting a thin Y 2 O 3 sectored piece on the premixed YBCO + BaSnO 3 composite targets by means of silver paste. F pmax value increases systematically with incorporation of 1D and 1D and 3D APCs and it also shifts towards higher applied magnetic fields. Films with 1D APCs exhibit a strong J C peak at Θ = 0° (H//c-axis) whereas films consisting of hybrid APCs exhibit enhanced J C at all the investigated angular regimes. A possible mechanism of vortex pinning in samples with hybrid APCs is also discussed suggesting the role of 1D and 3D APCs. (paper)
International Nuclear Information System (INIS)
Yamada, Y.; Murase, S.; Wada, H.; Tachikawa, K.
1985-01-01
The effects of cold-working on high-field pinning behaviour at 1.8 K and 4.2 K have been studied for multifilamentary NbTi, NbTiHf and NbTiTa superconductors, which were subjected to cold-working, heat treatment and cold-working, in sequence. It is found that the cold-working, either before or after heat treatment, shifts the peak in pinning force density to a higher field, while the maximum pinning force value is first increased with increasing amount of cold-working, and then decreased. This result can not be predicted by existing pinning theories, and we conclude that for pinning behaviour induced by cold-working, not only the introduction of pinning centres but also their size and spacing must be taken into account. (author)
International Nuclear Information System (INIS)
Kleykamp, H.; Muehling, G.
2005-09-01
The fabrication of uranium-plutonium oxide fuel started in Forschungszentrum Karlsruhe and at ALKEM company to begin for the criticality experiments in the SNEAK reactor and subsequently for stationary fuel pin irradiations in the FR2, BR2, DFR, Rapsodie, Phenix and KNK II reactors. The production methods comprised first the mechanical blending of UO2 and PuO2 followed by direct pressing and sintering of the pellets, later the advanced methods such as optimized comilling and ammonium uranyl plutonyl coprecititation. The fabrication of pellets was described in the main, further the alternative fuel pin manufacturing processes by vibrational compaction and hot-impact densification were discussed. The first capsule and pin irradiations in the FR2 and BR2 reactors contributed to the assessment of the maximum operation parameters within the fuel pin development such as linear heat rating, cladding temperature and burnup. Subsequently, small-bundle and largebundle irradiations were made in fast reactors in cooperation with Interatom company in order to verify the specifications for the commercial fast reactor SNR 300. Milestones were the maximum burnup of 175 GWd/t metal, corresponding 18.6 % of the heavy atoms, obtained in one of the KNK II fuel pin assemblies, and the displacement rates in the cladding materials of 140 dpa NRT attained in the Phenix reactor. Higher implications gained later the stationary irradiations of defected mixed-oxide pins, the mild fuel pin transient operations, the local blockage experiments and the severe hypothetic accidents in the respective Siloe, HFR, BR2 and CABRI reactors. These experiments were made solely in international partnership. Further activities were the chemical analyses of solid residues and coprecipitations of irradiated mixed-oxide fuels in the head-end of the reprocessing. All these actions were coordinated in the then fast breeder project. Furthermore, irradiated fuels and fuel pins of other reactor types were
International Nuclear Information System (INIS)
Crossland, I.G.
1982-01-01
Some of the more important mechanisms by which pin bowing can occur in Advanced Gas Cooled Reactors are examined. These include creep relaxation of the stresses which occur when thermal bowing is restrained and asymmetric axial clad creep. The clad temperature changes which accompany such bowing are also investigated and the theoretical results briefly compared with the empirical behaviour. (author)
ANALISIS RELEVANSI LULUSAN PERGURUAN TINGGI DENGAN DUNIA KERJA
Directory of Open Access Journals (Sweden)
Ali Muhson
2012-04-01
Full Text Available Abstract: A Relevance Analysis of University Graduates with World of Work. Education should be oriented to the competencies required by the workforce as a percentage of unemployment among the educated increase continuously. This study aims to examine the relevance of YSU Economic Education graduates. The study only focuses on the type of work and subjects taught. The subject of this study is the alumni of Economic Education Study Program. Sampling technique used is snowball sampling. Data collection technique using questionnaires and documentation while the technique of data analysis using descriptive analysis. The result suggests that the majority of the graduates find their first job as private a teacher, a private employee and a tutor, while current job of the most graduates are private teacher, private employee, and civil servant (teacher. The data shows that more than 50 percent of the graduates work in the education area. This implies that the relevance level based on the type of work is categorized as sufficient. Majority of the graduates teaches social science, economic, and entrepreneurship, hence it can be concluded that the relevance level based on the subjects taught is highly relevant. Keyword: relevance of graduates, type of work, unemployment, employment Abstrak: Analisis Relevansi Lulusan Perguruan Tinggi dengan Dunia Kerja. Pendidikan harus berorientasi pada kompetensi yang dibutuhkan oleh dunia kerja karena persentase penganggur di kalangan terdidik terus meningkat. Penelitian ini bertujuan untuk mengkaji tingkat relevansi (kesesuaian lulusan Pendidikan Ekonomi UNY. Kajian hanya diarahkan pada jenis pekerjaan dan mata pelajaran yang diampu. Penelitian ini mengambil subjek alumni Prodi Pendidikan Ekonomi dari berbagai angkatan. Teknik sampling yang digunakan adalah snowball sampling. Teknik pengumpulan data menggunakan angket dan dokumentasi sedangkan teknik analisis data menggunakan analisis deskriptif. Penelitian ini
Parallel two-phase-flow-induced vibrations in fuel pin model
International Nuclear Information System (INIS)
Hara, Fumio; Yamashita, Tadashi
1978-01-01
This paper reports the experimental results of vibrations of a fuel pin model -herein meaning the essential form of a fuel pin from the standpoint of vibration- in a parallel air-and-water two-phase flow. The essential part of the experimental apparatus consisted of a flat elastic strip made of stainless steel, both ends of which were firmly supported in a circular channel conveying the two-phase fluid. Vibrational strain of the fuel pin model, pressure fluctuation of the two-phase flow and two-phase-flow void signals were measured. Statistical measures such as power spectral density, variance and correlation function were calculated. The authors obtained (1) the relation between variance of vibrational strain and two-phase-flow velocity, (2) the relation between variance of vibrational strain and two-phase-flow pressure fluctuation, (3) frequency characteristics of variance of vibrational strain against the dominant frequency of the two-phase-flow pressure fluctuation, and (4) frequency characteristics of variance of vibrational strain against the dominant frequency of two-phase-flow void signals. The authors conclude that there exist two kinds of excitation mechanisms in vibrations of a fuel pin model inserted in a parallel air-and-water two-phase flow; namely, (1) parametric excitation, which occurs when the fundamental natural frequency of the fuel pin model is related to the dominant travelling frequency of water slugs in the two-phase flow by the ratio 1/2, 1/1, 3/2 and so on; and (2) vibrational resonance, which occurs when the fundamental frequency coincides with the dominant frequency of the two-phase-flow pressure fluctuation. (auth.)
A model of high-rate indentation of a cylindrical striking pin into a deformable body
Zalazinskaya, E. A.; Zalazinsky, A. G.
2017-12-01
Mathematical modeling of an impact and high-rate indentation to a significant depth of a flat-faced hard cylindrical striking pin into a massive deformable target body is carried out. With the application of the kinematic extreme theorem of the plasticity theory and the kinetic energy variation theorem, the phase trajectories of the striking pin are calculated, the initial velocity of the striking pin in the body, the limit values of the inlet duct length, and the depth of striking pin penetration into the target are determined.
Effects of magnetizing on flux pinning force for sintered YBCO superconductor
International Nuclear Information System (INIS)
Ding, S.Y.; Yan, J.L.; Yu, Z.; Shi, K.X.; Tong, H.W.; Qiu, L.
1989-01-01
It is shown that magnitude and course of magnetizing field influence magnetization and transport current. Effective flux pinning force density with two types is extracted by an iterative procedure based on the critical state equation. One of the types is attributed to the weak links and the other is considered to be resulted from the intragrain flux pinning centers
Computation of 3D neutron fluxes in one pin hexagonal cell
International Nuclear Information System (INIS)
Prabha, Hem; Marleau, Guy
2013-01-01
Highlights: ► Computations of 3D neutron fluxes in one pin hexagonal cell is performed by Carlvik’s method of collision probability. ► Carlvik’s method requires computation of track lengths in the geometry. ► Equations are developed to compute tracks, in 2D and 3D, in hexagons and are implemented in a program HX7. ► The program HX7 is implemented in NXT module of the code DRAGON, where tracks in pins are computed. ► The tracks are plotted and fluxes are compared with the EXCELT module of the code DRAGON. - Abstract: In this paper we are presenting the method of computation of three dimensional (3D) neutron fluxes in one pin hexagonal cell. Carlvik’s collision probability method of solving neutron transport equation for computing fluxes has been used here. This method can consider exact geometrical details of the given geometry. While using this method, track length computations are required to be done. We have described here the method of computing tracks in one 3D hexagon. A program HX7 has been developed for this purpose. This program has been implemented in the NXT module of the code DRAGON, where tracks in the pins are computed. For computing tracks in 3D, first we use the tracks computed in the two dimensions (2D) and then we project them in the third dimension. We have developed equations for this purpose. In both the regions, fuel pin as well as in the moderator surrounding the pin the fluxes are assumed to be uniform. A uniform source is assumed in the moderator region. Reflecting boundary conditions are applied on all the sides as well as on the top and bottom surfaces. One group 2D and 3D fluxes are compared with the respective results obtained by the EXCELT module of DRAGON. To check the computations, tracks are plotted and errors in the computations are obtained. It is observed by using both the modules EXCELT and NXT that the fluxes in the pins converge faster and in the moderator region fluxes converge very slowly
Calculation of fuel pin failure timing under LOCA conditions
International Nuclear Information System (INIS)
Jones, K.R.; Wade, N.L.; Siefken, L.J.; Straka, M.; Katsma, K.R.
1991-10-01
The objective of this research was to develop and demonstrate a methodology for calculation of the time interval between receipt of the containment isolation signals and the first fuel pin failure for loss-of-coolant accidents (LOCAs). Demonstration calculations were performed for a Babcock and Wilcox (B ampersand W) design (Oconee) and a Westinghouse (W) 4-loop design (Seabrook). Sensitivity studies were performed to assess the impacts of fuel pin burnup, axial peaking factor, break size, emergency core cooling system (ECCS) availability, and main coolant pump trip on these items. The analysis was performed using a four-code approach, comprised of FRAPCON-2, SCDAP/RELAP5/MOD3, TRAC-PF1/MOD1, and FRAP-T6. In addition to the calculation of timing results, this analysis provided a comparison of the capabilities of SCDAP/RELAP5/MOD3 with TRAC-PF1/MOD1 for large-break LOCA analysis. This paper discusses the methodology employed and the code development efforts required to implement the methodology. The shortest time intervals calculated between initiation of containment isolation and fuel pin failure were 11.4 s and 19.1 for the B ampersand W and W plants, respectively. The FRAP-T6 fuel pin failure times calculated using thermal-hydraulic data generated by SCDAP/RELAP5/MOD3 were more conservative than those calculated using data generated by TRAC-PF1/MOD1. 18 refs., 7 figs., 4 tabs
Badea, Robert; Berezovsky, Jesse
2016-06-01
The propagation of domain walls in a ferromagnetic film is largely determined by domain-wall pinning at defects in the material. In this article, we map the effective potential landscape for domain-wall pinning in permalloy films by raster scanning a single ferromagnetic vortex and monitoring the hysteretic vortex displacement vs applied magnetic field. The measurement is carried out using a differential magneto-optical microscopy technique which yields spatial sensitivity of approximately 10 nm. We present a simple algorithm for extracting an effective pinning potential from the measurement of vortex displacement vs applied field. The resulting maps of the pinning potential reveal distinct types of pinning sites, which we attribute to quasi-zero-, one-, and two-dimensional defects in the permalloy film.
Transfixation pinning and casting of tibial fractures in calves: five cases (1985-1989).
St-Jean, G; Clem, M F; DeBowes, R M
1991-01-01
Medical records of 5 calves with tibial fractures that were reduced and stabilized by transfixation pinning and casting were reviewed. Multiple Steinmann pins were placed transversely through proximal and distal fracture fragments, and the pin ends were incorporated in fiberglass cast material after fracture reduction. Cast material serves as an external frame to maintain pin position and fracture reduction. Calves were between 2 weeks and 6 months old and weighed between 40 and 180 kg. Three fractures were spiral in configuration and 2 were comminuted. One tibial fracture was open. After surgery, all calves were ambulatory within 24 hours. To improve tarsal flexion and achieve normal stance in 3 calves, cast revision was required on the caudal aspect of the limb. Good radiographic and clinical evidence of stability was observed in 5 to 10 weeks (mean 8 weeks), at which time the pis and cast were removed. Return to normal function was rapid and judged to be excellent at follow-up evaluation 3 to 12 months later. Advantages of transfixation pinning and casting in management of tibial fractures include flexibility in pin positioning, adequate maintenance of reduction, early return to weight-bearing status, joint mobility, and ease of ambulation. The inability to adjust fixation and alignment after cast application is a disadvantage of this technique compared with other external fixators.
Symmetric Pin Diversion Detection using a Partial Defect Detector (PDET)
International Nuclear Information System (INIS)
Sitaraman, S.; Ham, Y.S.
2009-01-01
Since the signature from the Partial Defect Detector (PDET) is principally dependent on the geometric layout of the guide tube locations, the capability of the technique in detecting symmetric diversion of pins needs to be determined. The Monte Carlo simulation study consisted of cases where pins were removed in a symmetric manner and the resulting signatures were examined. In addition to the normalized gamma-to-neutron ratios, the neutron and gamma signatures normalized to their maximum values, were also examined. Examination of the shape of the three curves as well as of the peak-to-valley differences in excess of the maximum expected in intact assemblies, indicated pin diversion. A set of simulations with various symmetric patterns of diversion were examined. The results from these studies indicated that symmetric diversions as low as twelve percent could be detected by this methodology
ANALISIS KONTRIBUSI PAJAK HOTEL TERHADAP PENDAPATAN ASLI DAERAH KABUPATEN NUNUKAN
-, MULIATI
2014-01-01
2014 Analisis Kontribusi Pajak Hotel terhadap Pendapatan Asli Daerah Kabupaten Nunukan Analysis of The Contributions Tax on Hotel Againts Regional Renenue Nunukan District Muliati Haerial M. Christian Mangiwa Penelitian ini bertujuan untuk mengetahui seberapa besar kontribusi pajak hotel terhadap pendapatan asli daerah, mengetahui sistem pengawasan, dan potensi yang ada untuk meningkatkan pajak hotel, mengetahui sistem dan prosedur...
Comparative analysis of different methods of modelling of most loaded fuel pin in transients
International Nuclear Information System (INIS)
Ovdiyenko, Y.; Khalimonchuk, V.; Ieremenko, M.
2007-01-01
Different methods of modeling of most loaded fuel pin are presented at the work. Calculation studies are performed on example of accident related to WWER-1000 cluster rod ejection with using of spatial kinetic code DYN3D that uses nodal method to calculate distribution of neutron flux in the core. Three methods of modeling of most loaded fuel pin are considered - flux reconstruction in fuel macrocell, pin-by-pin calculation by using of DYN3D/DERAB package and by introducing of additional 'hot channel'. Obtained results of performed studies could be used for development of calculation kinetic models during preparing of safety analysis report (Authors)
Fabrication of uranium-plutonium mixed nitride fuel pins (88F-5A) for first irradiation test at JMTR
International Nuclear Information System (INIS)
Suzuki, Yasufumi; Iwai, Takashi; Arai, Yasuo; Sasayama, Tatsuo; Shiozawa, Ken-ichi; Ohmichi, Toshihiko; Handa, Muneo
1990-07-01
A couple of uranium-plutonium mixed nitride fuel pins was fabricated for the first irradiation tests at JMTR for the purpose of understanding the irradiation behavior and establishing the feasibility of nitride fuels as advanced FBR fuels. The one of the pins was fitted with thermocouples in order to observe the central fuel temperature. In this report, the fabrication procedure of the pins such as pin design, fuel pellet fabrication and characterizations, welding of fuel pins, and inspection of pins are described, together with the outline of the new TIG welder installed recently. (author)
Investigation of the ramp testing behaviour of fuel pins with different diameters
International Nuclear Information System (INIS)
Pott, G.; Herren, M.; Wigger, B.
1979-09-01
The aim of these experiments was the investigation of the influence of different fuel pin diameter on the ramp testing behaviour. Fuel elements with diameter between 10,75 and 15,6 mm and different cladding thickness had been ramptested in the HBWR (Halden Boiling Water Reactor) after preirradiated in the same facility. Fuel pins with the smallest diameter of 10,75 mm failed. This was indicated by fission gas release measurement. Metallographic examination showed these failure were caused by hydride blisters. A systematic influence of fuel pin diameter and cladding thickness on the ramptesting behaviour was not observed. (orig.) [de
Transfixation pinning and casting of radial-ulnar fractures in calves: A review of three cases.
St-Jean, G; Debowes, R M
1992-04-01
We reviewed the medical records of three calves with radial-ulnar fractures which were reduced and stabilized by transfixation pinning and casting. Multiple Steinmann pins were placed transversely through proximal and distal fracture fragments and the pin ends were incorporated in fiberglass cast material after fracture reduction. Cast material was placed from proximal to distal radius and served as an external frame to maintain pin position and fracture reduction.At the time of injury, the calves ranged in age from one day to two months and weighed from 37-102 kg. Two fractures were comminuted and one was transverse. All fractures were closed. After surgery, all calves could walk within 24 hours. Radiographic and clinical evidence of fracture healing was present five to seven weeks (mean 6) after surgery. At that time, the pins and cast material were removed. Return to normal function was rapid and judged to be excellent at follow-up evaluation five to nine months later.Advantages of transfixation pinning and casting in management of radial-ulnar fractures include flexibility in pin positioning, adequate maintenance of reduction, early return to weight-bearing status, preservation of joint mobility, and ease of ambulation. The inability to adjust fixation and alignment after cast application is a disadvantage of this technique compared with other external fixators. We concluded that transfixation pinning is a useful means of stabilizing radial-ulnar fractures in pediatric bovine patients.
Creep relaxation of fuel pin bending and ovalling stresses
International Nuclear Information System (INIS)
Chan, D.P.; Jackson, R.J.
1979-06-01
Analytical methods for calculating fuel pin cladding bending and ovalling stresses due to pin bundle-duct mechanical interaction taking into account nonlinear creep are presented. Calculated results are in close agreement with finite element results by MARC-CDC program. The methods are used to investigate the effect of creep on the FTR fuel cladding bending and ovalling stresses. It is concluded that the cladding of 316 SS 20% CW and reference design has high creep rates in the FTR core region to keep the bending and ovalling stresses to low levels
International Nuclear Information System (INIS)
Nishimura, M.; Kamide, H.; Miyake, Y.
1997-04-01
Temperature distributions in fuel subassemblies of fast reactors interactively affect heat transfer from center to outer region of the core (inter-subassembly heat transfer) and cooling capability of an inter-wrapper flow, as well as maximum cladding temperature. The prediction of temperature distribution in the subassembly is, therefore one of the important issues for the reactor safety assessment. Mixing factors were applied to multi-dimensional thermal-hydraulic code AQUA to enhance the predictive capability of simulating maximum cladding temperature in the fuel subassemblies. In the previous studies, this analytical method had been validated through the calculations of the sodium experiments using driver subassembly test rig PLANDTL-DHX with 37-pin bundle and blanket subassembly test rig CCTL-CFR with 61-pin bundle. The error of the analyses were comparable to the error of instrumentation's. Thus the modeling was capable of predicting thermal-hydraulic field in the middle scale subassemblies. Before the application to large scale real subassemblies with more than 217 pins, accuracy of the analytical method have to be inspected through calculations of sodium tests in a large scale pin bundle. Therefore, computations were performed on sodium experiments in the relatively large 169-pin subassembly which had heater pins sparsely within the bundle. The analysis succeeded to predict the experimental temperature distributions. The errors of temperature rise from inlet to maximum values were reduced to half magnitudes by using mixing factors, compared to those of analyses without mixing factors. Thus the modeling is capable of predicting the large scale real subassemblies. (author)
Behavior of a bundle of fast fuel pins under irradiation
International Nuclear Information System (INIS)
Marbach, G.; Millet, P.; Robert, J.; Languille, A.
1979-01-01
In the French design of fuel elements for fast reactors, great deformation of pins can bring about interaction with the hexagonal tube through the spacer wires. The change in such bundles is described here when the diameter of the cladding increases and the outcome of this reaction (bending and ovalization of pins) is calculated with a simplified model. It is shown that the results achieved agree well with the experimental observations [fr
Surface barrier and bulk pinning in MgB$_2$ superconductor
Pissas, M.; Moraitakis, E.; Stamopoulos, D.; Papavassiliou, G.; Psycharis, V.; Koutandos, S.
2001-01-01
We present a modified method of preparation of the new superconductor MgB$_2$. The polycrystalline samples were characterized using x-ray and magnetic measurements. The surface barriers control the isothermal magnetization loops in powder samples. In bulk as prepared samples we always observed symmetric magnetization loops indicative of the presence of a bulk pinning mechanism. Magnetic relaxation measurements in the bulk sample reveal a crossover of surface barrier to bulk pinning.
International Nuclear Information System (INIS)
Dobrovolskiy, Oleksandr V.; Begun, Evgeniya; Huth, Michael; Shklovskij, Valerij A.
2013-01-01
Highlights: •We fabricated an array of grooves in Nb films by using focused ion beam milling. •We determined the material composition in different areas of the processed films. •We deduced the pinning activation energies from the magneto-resistivity data. •We obtained the material composition – pinning strength correlation in the processed films. -- Abstract: An analysis of the interrelated changes in the material composition and the pinning strength in nanostructured Nb (1 1 0) thin films is presented. The nanopatterns were prepared by focused ion beam milling of an array of uniaxial grooves. They induce a washboard-like pinning potential landscape for vortices in the mixed state. By applying different magnetic fields, the most likely pinning sites along which the flux lines move through the samples have been selected. By this, either the background isotropic pinning of the pristine film or the enhanced isotropic pinning originating from the nanoprocessing has been probed. The enhanced pinning strength in the processed films has been found to correlate with the content of Ga implanted into the films during the nanopatterning
Energy Technology Data Exchange (ETDEWEB)
Dobrovolskiy, Oleksandr V., E-mail: Dobrovolskiy@Physik.uni-frankfurt.de [Physikalisches Institut, Goethe-Universität, 60438 Frankfurt am Main (Germany); Physical Department, Kharkiv National University, 61077 Kharkiv (Ukraine); Begun, Evgeniya; Huth, Michael [Physikalisches Institut, Goethe-Universität, 60438 Frankfurt am Main (Germany); Shklovskij, Valerij A. [Physical Department, Kharkiv National University, 61077 Kharkiv (Ukraine); Institute for Theoretical Physics, NSC-KIPT, 61108 Kharkiv (Ukraine)
2013-11-15
Highlights: •We fabricated an array of grooves in Nb films by using focused ion beam milling. •We determined the material composition in different areas of the processed films. •We deduced the pinning activation energies from the magneto-resistivity data. •We obtained the material composition – pinning strength correlation in the processed films. -- Abstract: An analysis of the interrelated changes in the material composition and the pinning strength in nanostructured Nb (1 1 0) thin films is presented. The nanopatterns were prepared by focused ion beam milling of an array of uniaxial grooves. They induce a washboard-like pinning potential landscape for vortices in the mixed state. By applying different magnetic fields, the most likely pinning sites along which the flux lines move through the samples have been selected. By this, either the background isotropic pinning of the pristine film or the enhanced isotropic pinning originating from the nanoprocessing has been probed. The enhanced pinning strength in the processed films has been found to correlate with the content of Ga implanted into the films during the nanopatterning.
Magnetically pinned ring dots for spin valve or magnetic tunnel junction memory cells
International Nuclear Information System (INIS)
Nakatani, Ryoichi; Yoshida, Tetsuo; Endo, Yasushi; Kawamura, Yoshio; Yamamoto, Masahiko; Takenaga, Takashi; Aya, Sunao; Kuroiwa, Takeharu; Beysen, Sadeh; Kobayashi, Hiroshi
2005-01-01
Ni-Fe/Mn-Ir asymmetric ring dots with partially planed outer sides are investigated in order to confirm a method for obtaining pinned layers in magnetic memories with asymmetric ring shapes. Magnetic force microscopy revealed that the direction of vortical magnetization is pinned in Ni-Fe/Mn-Ir asymmetric ring dots despite the direction of the magnetic fields. This investigation shows that the Ni-Fe/Mn-Ir asymmetric ring dots can be applied to pinned layers in magnetic memories with asymmetric ring shapes
Collective-pinning properties of superconducting a-NbxGe and a-MoxSi films
International Nuclear Information System (INIS)
Woerdenweber, R.
1987-01-01
This thesis describes a study of superconducting flux pinning in amorphous NbGe and MoSi films of various compositions and thickness. Amorphous NbGe and MoSi alloys belong to the weak-coupling type-II superconductors in the extreme dirty limit. This feature enables to determine several important superconducting parameters from well-known theoretical expressions. It is also responsible for the weak pinning, which is necessary to observe the two-dimensional collective pinning properties according to the Larkin-Ovchinnikov theory. (Auth.)
Reversible rectification of vortex motion in magnetic and non-magnetic asymmetric pinning potentials
International Nuclear Information System (INIS)
Gonzalez, E.M.; Gonzalez, M.P.; Nunez, N.O.; Villegas, J.E.; Anguita, J.V.; Jaafa, M.; Asenjo, A.; Vicent, J.L.
2006-01-01
Nb films have been grown on arrays of asymmetric pinning centers. The lattice vortex dynamics could be modified, almost at will, by periodic pinning potentials. In the case of asymmetric pinning potentials a vortex ratchet effect occurs: the vortex lattice motion is rectified. That is, an injected ac current yields an output dc voltage, which polarity could be tuned. The output signal polarity could be switched with the applied magnetic field and the ac current strength. Ratchet effect occurs when asymmetric potentials induce outward particles flow under external fluctuations in the lack of driven direct outward forces. The output signal is similar using magnetic or non-magnetic submicrometric array of pinning centers. This device works as an adiabatic rocking ratchet. This superconducting ratchet could be a model to study biological motors
Influence of flexible pin for planets on service life of wind turbine gearboxes
International Nuclear Information System (INIS)
Park, Young Jun; Lee, Geun Ho; Nam, Yong Yun; Kim, Jeong Kil
2012-01-01
An overhung mounted carrier with flexible pins is applied to the planetary gear train of a wind turbine gearbox to investigate the influence of the self aligning effect by means of the deflection of the planet spindle and the flexible pin on the lifetime of the planet gear for a wind turbine gearbox. To analyze the load distribution of planet gears, both Euler theory and commercial software are employed. By applying an overhung mounted carrier with flexible pins in the wind turbine gearbox, we can improve the misalignment performance, face load factor, and service life of the planet gears. In particular, it was confirmed that a service life of more than 20 years could be realized for wind turbine gearboxes by applying a flexible pin to overhung mounted carrier
Artificial pinning centers using the barrier layer of ordered nanoporous alumina templates
DEFF Research Database (Denmark)
Hallet, X.; Mátéfi-Tempfli, Stefan; Mátéfi-Tempfli, M.
2009-01-01
of approximately 50nm. Using this surface as a template for controlling the pinning in thin superconducting films, superconducting Nb was deposited with different thicknesses and under different deposition angles. The evaporation under a 30° angle shows an asymmetric pinning potential composed of two triangular...
Fast reactor fuel pin behavior analyses in a LOF type transient event
International Nuclear Information System (INIS)
Mizuno, Tomoyasu; Koyama, Shin-ichi; Kaito, Takeji; Uwaba, Tomoyuki; Tanaka, Kenya
2013-06-01
In order to evaluate integrity limiting parameters of fuel pins during fast reactor core transient events, such as fuel center line temperature and cladding maximum temperature, fuel pin behavior calculations were made using the fast reactor fuel pin performance code CEDAR. The temperature histories of fuel pins during a loss of flow (LOF) type transient events was calculated based on Ross and Stoute type gap conductance model and constant gap conductance model, which is used in a core transient calculation code like HIPRAC. The calculated maximum temperatures of cladding and adjacent coolant channel were lower in the case with Ross and Stoute type model than in the case of constant gap conductance model due to the dynamic change of gap conductance of former case. It is indicated that core transient calculations with constant gap conductance give conservative cladding and coolant temperatures than that with Ross and Stoute type gap conductance model which is thought to be realistic. (author)