Linear and non-linear optics of nano-scale 2‧,7‧dichloro-fluorescein/FTO optical system: Bandgap and dielectric analysis

Science.gov (United States)

Iqbal, Javed; Yahia, I. S.; Zahran, H. Y.; AlFaify, S.; AlBassam, A. M.; El-Naggar, A. M.

2016-12-01

2‧,7‧ dichloro-Fluorescein (DCF) is a promising organic semiconductor material in different technological aspects such as solar cell, photodiode, Schottky diode. DCF thin film/conductive glass (FTO glass) was prepared by a low-cost spin coating technique. The spectrophotometric data such as the absorbance, reflectance and transmittance were cogitated in the 350-2500 nm wavelength range, at the normal incidence. The absorption (n) and linear refractive indices (k) were computed using the Fresnel's equations. The optical band gap was evaluated and it was found that there is two band gap described as follows: (1) It is related to the band gap of FTO/glass which is equal 3.4 eV and (2) the second one is related to the absorption edge of DCF equals 2.25 eV. The non-linear parameters such as the refractive index (n2) and optical susceptibility χ(3) were evaluated by the spectroscopic method based on the refractive index. Both (n2) and χ(3) increased rapidly on increasing the wavelength with redshift absorption. Our work represents a new idea about using FTO glass for a new generation of the optical device and technology.

Titanium dioxide-coated fluorine-doped tin oxide thin films for improving overall photoelectric property

Energy Technology Data Exchange (ETDEWEB)

Li, Bao-jia, E-mail: bjia_li@126.com [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Jiangsu Provincial Key Laboratory of Center for Photon Manufacturing Science and Technology, Jiangsu University, Zhenjiang 212013 (China); Huang, Li-jing [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Jiangsu Provincial Key Laboratory of Center for Photon Manufacturing Science and Technology, Jiangsu University, Zhenjiang 212013 (China); Ren, Nai-fei [Jiangsu Provincial Key Laboratory of Center for Photon Manufacturing Science and Technology, Jiangsu University, Zhenjiang 212013 (China); School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013 (China); Zhou, Ming [The State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China)

2014-01-30

Titanium (Ti) layers were deposited by direct current (DC) magnetron sputtering on commercial fluorine-doped tin oxide (FTO) glasses, followed by simultaneous oxidation and annealing treatment in a tubular furnace to prepare titanium dioxide (TiO{sub 2})/FTO bilayer films. Large and densely arranged grains were observed on all TiO{sub 2}/FTO bilayer films. The presence of TiO{sub 2} tetragonal rutile phase in the TiO{sub 2}/FTO bilayer films was confirmed by X-ray diffraction (XRD) analysis. The results of parameter optimization indicated that the TiO{sub 2}/FTO bilayer film, which was formed by adopting a temperature of 400 °C and an oxygen flow rate of 15 sccm, had the optimal overall photoelectric property with a figure of merit of 2.30 × 10{sup −2} Ω{sup −1}, higher than 1.78 × 10{sup −2} Ω{sup −1} for the FTO single-layer film. After coating a 500 nm-thick AZO layer by DC magnetron sputtering on this TiO{sub 2}/FTO bilayer film, the figure of merit of the trilayer film achieved to a higher figure of merit of 3.12 × 10{sup −2} Ω{sup −1}, indicating further improvement of the overall photoelectric property. This work may provide a scientific basis and reference for improving overall photoelectric property of transparent conducting oxide (TCO) films.

Trade-off between Zr Passivation and Sn Doping on Hematite Nanorod Photoanodes for Efficient Solar Water Oxidation: Effects of a ZrO2 Underlayer and FTO Deformation.

Science.gov (United States)

Subramanian, Arunprabaharan; Annamalai, Alagappan; Lee, Hyun Hwi; Choi, Sun Hee; Ryu, Jungho; Park, Jung Hee; Jang, Jum Suk

2016-08-03

Herein we report the influence of a ZrO2 underlayer on the PEC (photoelectrochemical) behavior of hematite nanorod photoanodes for efficient solar water splitting. Particular attention was given to the cathodic shift in onset potential and photocurrent enhancement. Akaganite (β-FeOOH) nanorods were grown on ZrO2-coated FTO (fluorine-doped tin oxide) substrates. Sintering at 800 °C transformed akaganite to the hematite (α-Fe2O3) phase and induced Sn diffusion into the crystal structure of hematite nanorods from the FTO substrates and surface migration, shallow doping of Zr atoms from the ZrO2 underlayer. The ZrO2 underlayer-treated photoanode showed better water oxidation performance compared to the pristine (α-Fe2O3) photoanode. A cathodic shift in the onset potential and photocurrent enhancement was achieved by surface passivation and shallow doping of Zr from the ZrO2 underlayer, along with Sn doping from the FTO substrate to the crystal lattice of hematite nanorods. The Zr based hematite nanorod photoanode achieved 1 mA/cm(2) at 1.23 VRHE with a low turn-on voltage of 0.80 VRHE. Sn doping and Zr passivation, as well as shallow doping, were confirmed by XPS, Iph, and M-S plot analyses. Electrochemical impedance spectroscopy revealed that the presence of a ZrO2 underlayer decreased the deformation of FTO substrate, improved electron transfer at the hematite/FTO interface and increased charge-transfer resistance at the electrolyte/hematite interface. This is the first systematic investigation of the effects of Zr passivation, shallow doping, and Sn doping on hematite nanorod photoanodes through application of a ZrO2 underlayer on the FTO substrate.

High efficiency bifacial Cu2ZnSnSe4 thin-film solar cells on transparent conducting oxide glass substrates

Directory of Open Access Journals (Sweden)

Jung-Sik Kim

2016-09-01

Full Text Available In this work, transparent conducting oxides (TCOs have been employed as a back contact instead of Mo on Cu2ZnSnSe4 (CZTSe thin-film solar cells in order to examine the feasibility of bifacial Cu2ZnSn(S,Se4 (CZTSSe solar cells based on a vacuum process. It is found that the interfacial reaction between flourine doped tin oxide (FTO or indium tin oxide (ITO and the CZTSe precursor is at odds with the conventional CZTSe/Mo reaction. While there is no interfacial reaction on CZTSe/FTO, indium in CZTSe/ITO was significantly diffused into the CZTSe layers; consequently, a SnO2 layer was formed on the ITO substrate. Under bifacial illumination, we achieved a power efficiency of 6.05% and 4.31% for CZTSe/FTO and CZTSe/ITO, respectively.

3D FTO/FTO-Nanocrystal/TiO2 Composite Inverse Opal Photoanode for Efficient Photoelectrochemical Water Splitting.

Science.gov (United States)

Wang, Zhiwei; Li, Xianglin; Ling, Han; Tan, Chiew Kei; Yeo, Loo Pin; Grimsdale, Andrew Clive; Tok, Alfred Iing Yoong

2018-05-01

A 3D fluorine-doped SnO 2 (FTO)/FTO-nanocrystal (NC)/TiO 2 inverse opal (IO) structure is designed and fabricated as a new "host and guest" type of composite photoanode for efficient photoelectrochemical (PEC) water splitting. In this novel photoanode design, the highly conductive and porous FTO/FTO-NC IO acts as the "host" skeleton, which provides direct pathways for faster electron transport, while the conformally coated TiO 2 layer acts as the "guest" absorber layer. The unique composite IO structure is fabricated through self-assembly of colloidal spheres template, a hydrothermal method and atomic layer deposition (ALD). Owing to its large surface area and efficient charge collection, the FTO/FTO-NC/TiO 2 composite IO photoanode shows excellent photocatalytic properties for PEC water splitting. With optimized dimensions of the SnO 2 nanocrystals and the thickness of the ALD TiO 2 absorber layers, the 3D FTO/FTO-NC/TiO 2 composite IO photoanode yields a photocurrent density of 1.0 mA cm -2 at 1.23 V versus reversible hydrogen electrode (RHE) under AM 1.5 illumination, which is four times higher than that of the FTO/TiO 2 IO reference photoanode. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Fabrication and performance of the Pt-Ru/Ni-P/FTO counter electrode for dye-sensitized solar cells

International Nuclear Information System (INIS)

Ma, Huanmei; Tian, Jianhua; Bai, Shuming; Liu, Xiaodong; Shan, Zhongqiang

2014-01-01

Highlights: • Pt-Ru alloy acts as the catalyst of counter electrodes in dye-sensitized solar cell. • Ni-P/FTO (fluorine-doped SnO 2 ) substrate is prepared by electroless plating method. • Pt-Ru/Ni-P/FTO counter electrode is fabricated by electrodeposition method. • The Ni-P sublayer improves the conductivity and light reflectance of FTO substrate. • The cell with Pt-Ru/Ni-P/FTO counter electrode exhibits an improved efficiency. - Abstract: In this paper, Pt-Ru/Ni-P/FTO has been designed and fabricated as the counter electrode for dye-sensitized solar cells. The Pt-Ru catalytic layer and Ni-P alloy sublayer are prepared by traditional electrodeposition method and a simple electroless plating method, respectively, and the preparation conditions have been optimized. The scanning electron microscopy (SEM) images show that the Pt-Ru particles are evenly distributed on FTO and Ni-P/FTO substrate. By X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), it is confirmed that the Ni-P amorphous alloy has been formed, and no other compounds involved Ni and P have been formed. The electrochemical measurement results reveal that the Pt-Ru electrode has higher catalytic activity and stability towards tri-iodine reduction reaction than Pt electrode in the organic medium. The Ni-P sublayer deposited on FTO glasses increases the conductivity and light-reflection ability of the counter electrode, and this contributes to lowering the inner resistance of the cell and improving the light utilization efficiency. Through the photovoltaic test, it is confirmed that the energy conversion efficiency of a single DSSC with the optimized Pt-Ru/Ni-P/FTO counter electrode is increased by 29% compared with that of the cell based on the Pt/FTO counter electrode under the same conditions

Barium oxide, calcium oxide, magnesia, and alkali oxide free glass

Science.gov (United States)

Lu, Peizhen Kathy; Mahapatra, Manoj Kumar

2013-09-24

A glass composition consisting essentially of about 10-45 mole percent of SrO; about 35-75 mole percent SiO.sub.2; one or more compounds from the group of compounds consisting of La.sub.2O.sub.3, Al.sub.2O.sub.3, B.sub.2O.sub.3, and Ni; the La.sub.2O.sub.3 less than about 20 mole percent; the Al.sub.2O.sub.3 less than about 25 mole percent; the B.sub.2O.sub.3 less than about 15 mole percent; and the Ni less than about 5 mole percent. Preferably, the glass is substantially free of barium oxide, calcium oxide, magnesia, and alkali oxide. Preferably, the glass is used as a seal in a solid oxide fuel/electrolyzer cell (SOFC) stack. The SOFC stack comprises a plurality of SOFCs connected by one or more interconnect and manifold materials and sealed by the glass. Preferably, each SOFC comprises an anode, a cathode, and a solid electrolyte.

Preparation and characterization of sprayed FTO thin films

Science.gov (United States)

Abd-Lefdil, M.; Diaz, R.; Bihri, H.; Aouaj, M. Ait; Rueda, F.

2007-06-01

Fluorine doped tin oxide (FTO) thin films have been prepared by spray pyrolysis technique with no further annealing. Films with 2.5% of fluorine grown at 400 °C present a single phase and exhibit a tetragonal structure with lattice parameters a = 4.687 Å and c = 3.160 Å. Scanning electron micrographs showed homogeneous surfaces with average grain size around 190 nm. The films are transparent in the visible zone and exhibit a high reflectance in the near infrared region. The best electrical resistivity was 6.3 × 10-4 Ω cm for FTO with 2.5% of fluorine. The ratio of transmittance in the visible to the sheet resistance are in the 0.57 × 10-2 1.96 × 10-2 {Ω }-1 range.

Oxidation behaviour of metallic glass foams

Energy Technology Data Exchange (ETDEWEB)

Barnard, B.R. [Department of Materials Science and Engineering, 434 Dougherty Hall, University of Tennessee, Knoxville, TN 37996-2200 (United States)], E-mail: bbarnard@utk.edu; Liaw, P.K. [Department of Materials Science and Engineering, 434 Dougherty Hall, University of Tennessee, Knoxville, TN 37996-2200 (United States); Demetriou, M.D.; Johnson, W.L. [Department of Materials Science, Keck Laboratory, California Institute of Technology, Pasadena, CA 91125 (United States)

2008-08-15

In this study, the effects of porosity on the oxidation behaviour of bulk-metallic glasses were investigated. Porous Pd- and Fe-based bulk-metallic glass (BMG) foams and Metglas ribbons were studied. Oxidizing experiments were conducted at 70 deg. C, and around 80 deg. C below glass-transition temperatures, (T{sub g}s). Scanning-electron microscopy/energy-dispersive spectroscopy (SEM/EDS) studies revealed little evidence of oxidation at 70 deg. C. Specimens exhibited greater oxidation at T{sub g} - 80 deg. C. Oxides were copper-based for Pd-based foams, Fe-, Cr-, and Mo-based for Fe-based foams, and Co-based with borosilicates likely for the Metglas. Pd-based foams demonstrated the best oxidation resistance, followed by Metglas ribbons, followed by Fe-based foams.

Glass material oxidation and dissolution system: Converting miscellaneous fissile materials to glass

International Nuclear Information System (INIS)

Forsberg, C.W.; Ferrada, J.J.

1996-01-01

The cold war and the development of nuclear energy have resulted in significant inventories of miscellaneous fissile materials (MFMs). MFMs include (1) plutonium scrap and residue, (2) miscellaneous spent nuclear fuel (SNF), (3) certain hot cell wastes, and (4) many one-of-a-kind materials. Major concerns associated with the long-term management of these materials include: safeguards and nonproliferation issues; health, environment, and safety concerns. waste management requirements; and high storage costs. These issues can be addressed by converting the MFMs to glass for secure, long-term storage or repository disposal; however, conventional glass-making processes require oxide-like feed materials. Converting MFMs to oxide-like materials with subsequent vitrification is a complex and expensive process. A new vitrification process has been invented, the Glass Material Oxidation and Dissolution System (GMODS), which directly converts metals, ceramics, and amorphous solids to glass; oxidizes organics with the residue converted to glass; and converts chlorides to borosilicate glass and a secondary sodium chloride (NaCl) stream. Laboratory work has demonstrated the conversion of cerium (a plutonium surrogate), uranium, Zircaloy, stainless steel, multiple oxides, and other materials to glass. However, significant work is required to develop GMODS further for applications at an industrial scale. If implemented, GMODS will provide a new approach to manage these materials

Solid oxide fuel cell having a glass composite seal

Science.gov (United States)

De Rose, Anthony J.; Mukerjee, Subhasish; Haltiner, Jr., Karl Jacob

2013-04-16

A solid oxide fuel cell stack having a plurality of cassettes and a glass composite seal disposed between the sealing surfaces of adjacent cassettes, thereby joining the cassettes and providing a hermetic seal therebetween. The glass composite seal includes an alkaline earth aluminosilicate (AEAS) glass disposed about a viscous glass such that the AEAS glass retains the viscous glass in a predetermined position between the first and second sealing surfaces. The AEAS glass provides geometric stability to the glass composite seal to maintain the proper distance between the adjacent cassettes while the viscous glass provides for a compliant and self-healing seal. The glass composite seal may include fibers, powders, and/or beads of zirconium oxide, aluminum oxide, yttria-stabilized zirconia (YSZ), or mixtures thereof, to enhance the desirable properties of the glass composite seal.

Heavy metal oxide glasses as gamma rays shielding material

International Nuclear Information System (INIS)

Kaur, Preet; Singh, Devinder; Singh, Tejbir

2016-01-01

The gamma rays shielding parameters for heavy metal oxide glasses and concrete samples are comparable. However, the transparent nature of glasses provides additional feature to visualize inside the shielding material. Hence, different researchers had contributed in computing/measuring different shielding parameters for different configurations of heavy metal oxide glass systems. In the present work, a detailed study on different heavy metal (_5_6Ba, _6_4Gd, _8_2Pb, _8_3Bi) oxide glasses has been presented on the basis of different gamma rays shielding parameters as reported by different researchers in the recent years. It has been observed that among the selected heavy metal oxide glass systems, Bismuth based glasses provide better gamma rays shielding. Hence, Bismuth based glasses can be better substitute to concrete walls at nuclear reactor sites and nuclear labs.

Heavy metal oxide glasses as gamma rays shielding material

Energy Technology Data Exchange (ETDEWEB)

Kaur, Preet; Singh, Devinder; Singh, Tejbir, E-mail: dr.tejbir@gmail.com

2016-10-15

The gamma rays shielding parameters for heavy metal oxide glasses and concrete samples are comparable. However, the transparent nature of glasses provides additional feature to visualize inside the shielding material. Hence, different researchers had contributed in computing/measuring different shielding parameters for different configurations of heavy metal oxide glass systems. In the present work, a detailed study on different heavy metal ({sub 56}Ba, {sub 64}Gd, {sub 82}Pb, {sub 83}Bi) oxide glasses has been presented on the basis of different gamma rays shielding parameters as reported by different researchers in the recent years. It has been observed that among the selected heavy metal oxide glass systems, Bismuth based glasses provide better gamma rays shielding. Hence, Bismuth based glasses can be better substitute to concrete walls at nuclear reactor sites and nuclear labs.

Dense CdS thin films on fluorine-doped tin oxide coated glass by high-rate microreactor-assisted solution deposition

Energy Technology Data Exchange (ETDEWEB)

Su, Yu-Wei, E-mail: suyuweiwayne@gmail.com [School of Chemical, Biological and Environmental Engineering, Oregon State University, Corvallis, OR 97330 (United States); Microproducts Breakthrough Institute and Oregon Process Innovation Center, Corvallis, Oregon 97330 (United States); Ramprasad, Sudhir [Energy Processes and Materials Division, Pacific Northwest National Laboratory, Corvallis, OR 9730 (United States); Microproducts Breakthrough Institute and Oregon Process Innovation Center, Corvallis, Oregon 97330 (United States); Han, Seung-Yeol; Wang, Wei [School of Chemical, Biological and Environmental Engineering, Oregon State University, Corvallis, OR 97330 (United States); Microproducts Breakthrough Institute and Oregon Process Innovation Center, Corvallis, Oregon 97330 (United States); Ryu, Si-Ok [School of Display and Chemical Engineering, Yeungnam University, 214-1 Dae-dong, Gyeonsan, Gyeongbuk 712-749 (Korea, Republic of); Palo, Daniel R. [Barr Engineering Co., Hibbing, MN 55747 (United States); Paul, Brian K. [School of Mechanical, Industrial and Manufacturing Engineering, Oregon State University, Corvallis, OR 97330 (United States); Microproducts Breakthrough Institute and Oregon Process Innovation Center, Corvallis, Oregon 97330 (United States); Chang, Chih-hung [School of Chemical, Biological and Environmental Engineering, Oregon State University, Corvallis, OR 97330 (United States); Microproducts Breakthrough Institute and Oregon Process Innovation Center, Corvallis, Oregon 97330 (United States)

2013-04-01

Continuous microreactor-assisted solution deposition is demonstrated for the deposition of CdS thin films on fluorine-doped tin oxide (FTO) coated glass. The continuous flow system consists of a microscale T-junction micromixer with the co-axial water circulation heat exchanger to control the reacting chemical flux and optimize the heterogeneous surface reaction. Dense, high quality nanocrystallite CdS thin films were deposited at an average rate of 25.2 nm/min, which is significantly higher than the reported growth rate from typical batch chemical bath deposition process. Focused-ion-beam was used for transmission electron microscopy specimen preparation to characterize the interfacial microstructure of CdS and FTO layers. The band gap was determined at 2.44 eV by UV–vis absorption spectroscopy. X-ray photon spectroscopy shows the binding energies of Cd 3d{sub 3/2}, Cd 3d{sub 5/2}, S 2P{sub 3/2} and S 2P{sub 1/2} at 411.7 eV, 404.8 eV, 162.1 eV and 163.4 eV, respectively. - Highlights: ► CdS films deposited using continuous microreactor-assisted solution deposition (MASD) ► Dense nanocrystallite CdS films can be reached at a rate of 25.2 [nm/min]. ► MASD can approach higher film growth rate than conventional chemical bath deposition.

Improving the performance of nickel-coated fluorine-doped tin oxide thin films by magnetic-field-assisted laser annealing

Energy Technology Data Exchange (ETDEWEB)

Li, Bao-jia, E-mail: li_bjia@126.com [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Jiangsu Provincial Key Laboratory of Center for Photon Manufacturing Science and Technology, Jiangsu University, Zhenjiang 212013 (China); Huang, Li-jing [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Jiangsu Provincial Key Laboratory of Center for Photon Manufacturing Science and Technology, Jiangsu University, Zhenjiang 212013 (China); Ren, Nai-fei [Jiangsu Provincial Key Laboratory of Center for Photon Manufacturing Science and Technology, Jiangsu University, Zhenjiang 212013 (China); School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013 (China); Kong, Xia; Cai, Yun-long; Zhang, Jie-lu [Jiangsu Tailong Reduction Box Co. Ltd., Taixing 225400 (China)

2015-10-01

Highlights: • Ni/FTO films were prepared by sputtering Ni layers on commercial FTO glass. • The as-prepared Ni/FTO films underwent magnetic-field-assisted laser annealing. • Magnetic field and laser fluence were crucial for improving quality of the films. • All Ni/FTO films displayed enhanced compactness after magnetic laser annealing. • Magnetic laser annealing using a fluence of 0.9 J/cm{sup 2} led to the best film quality. - Abstract: Nickel-coated fluorine-doped tin oxide (Ni/FTO) thin films were prepared by sputtering Ni layers on commercial FTO glass. The as-prepared Ni/FTO films underwent nanosecond pulsed laser annealing in an external magnetic field (0.4 T). The effects of the presence of magnetic field and laser fluence on surface morphology, crystal structure and photoelectric properties of the films were investigated. All the films displayed enhanced compactness after magnetic-field-assisted laser annealing. It was notable that both crystallinity and grain size of the films gradually increased with increasing laser fluence from 0.6 to 0.9 J/cm{sup 2}, and then decreased slightly with an increase in laser fluence to 1.1 J/cm{sup 2}. As a result, the film obtained by magnetic-field-assisted laser annealing using a fluence of 0.9 J/cm{sup 2} had the best overall photoelectric property with an average transmittance of 81.2%, a sheet resistance of 5.5 Ω/sq and a figure of merit of 2.27 × 10{sup −2} Ω{sup −1}, outperforming that of the film obtained by pure laser annealing using the same fluence.

Oxidation behaviour of Zr-based bulk metallic glasses

International Nuclear Information System (INIS)

Wang, Bin

2011-01-01

The Zr-based bulk metallic glasses, developed since the late 1980's, have very interesting mechanical properties, which can be considered for many applications including working under oxidizing atmosphere conditions at high temperatures. It is therefore interesting to study their oxidation resistance and to characterize the oxide scale formed on alloys surface. The fundamental objective of this thesis is to enhance the understanding of the role of various thermodynamic and chemistry parameters on the oxidation behaviour of the Zr-based bulk metallic glasses at high temperature under dry air, to determine the residual stresses in the oxide layer, in comparison with their crystalline alloys with the same chemical composition after an annealing treatment. The oxidation kinetics of these glasses and the crystalline structure of oxide scale ZrO 2 depend on the temperature and the oxidation duration: for short periods of oxidation or at a temperature below Tg, the kinetics follows a parabolic law, whereas, if the sample is oxidized at T ≥ Tg, the kinetics can be divided into two parts. The crystalline counterparts are oxidized by a parabolic rule whatever the temperature; for long oxidation duration at a temperature close to Tg, the kinetics becomes more complex because of the crystallisation of the glasses during the oxidation tests. Also the crystalline structure of the oxide layers depends on the oxidation temperature: the oxide layer consists only in tetragonal Zirconia at T ≤ Tg, while monoclinic Zirconia was formed at higher temperature. The mechanism of the formation of the oxide scale is due to both the interior diffusion of Oxygen ions and the external diffusion of Zirconium ions. However the diffusion of Zirconium ions slows gradually during the crystallisation process of the glass matrix. When the crystallisation is completed, the formation of Zirconia is controlled by only the internal diffusion of oxygen ions. The corresponding residual stresses

Effect of post annealing treatment on electrochromic properties of spray deposited niobium oxide thin films

International Nuclear Information System (INIS)

Mujawar, S.H.; Inamdar, A.I.; Betty, C.A.; Ganesan, V.; Patil, P.S.

2007-01-01

Niobium oxide thin films were deposited on the glass and fluorine doped tin oxide (FTO) coated glass substrates using simple and inexpensive spray pyrolysis technique. During deposition of the films various process parameters like nozzle to substrate distance, spray rate, concentration of sprayed solution were optimized to obtain well adherent and transparent films. The films prepared were further annealed and effect of post annealing on the structural, morphological, optical and electrochromic properties was studied. Structural and morphological characterizations of the films were carried out using scanning electron microscopy, atomic force microscopy and X-ray diffraction techniques. Electrochemical properties of the niobium oxide thin films were studied by using cyclic-voltammetry, chronoamperometry and chronocoulometry

Conversion of plutonium-containing materials into borosilicate glass using the glass material oxidation and dissolution system

International Nuclear Information System (INIS)

Forsberg, C.W.; Beahm, E.C.; Parker, G.W.

1996-01-01

The end of the cold war has resulted in excess plutonium-containing materials (PCMs) in multiple chemical forms. Major problems are associated with the long-term management of these materials: safeguards and nonproliferation issues; health, environment, and safety concerns; waste management requirements; and high storage costs. These issues can be addressed by conversion of the PCMs to glass: however, conventional glass processes require oxide-like feed materials. Conversion of PCMs to oxide-like materials followed by vitrification is a complex and expensive process. A new vitrification process has been invented, the Glass Material Oxidation and Dissolution System (GMODS) to allow direct conversion of PCMs to glass. GMODS directly converts metals, ceramics, and amorphous solids to glass; oxidizes organics with the residue converted to glass; and converts chlorides to borosilicate glass and a secondary sodium chloride stream. Laboratory work has demonstrated the conversion of cerium (a plutonium surrogate), uranium (a plutonium surrogate), Zircaloy, stainless steel, multiple oxides, and other materials to glass. Equipment options have been identified for processing rates between 1 and 100,000 t/y. Significant work, including a pilot plant, is required to develop GMODS for applications at an industrial scale

Influences of Pr and Ta doping concentration on the characteristic features of FTO thin film deposited by spray pyrolysis

International Nuclear Information System (INIS)

Turgut, Güven; Koçyiğit, Adem; Sönmez, Erdal

2015-01-01

The Pr and Ta separately doped FTO (10 at.% F incorporated SnO 2 ) films are fabricated via spray pyrolysis. The microstructural, topographic, optical, and electrical features of fluorine-doped TO (FTO) films are investigated as functions of Pr and Ta dopant concentrations. The x-ray diffraction (XRD) measurements reveal that all deposited films show polycrystalline tin oxide crystal property. FTO film has (200) preferential orientation, but this orientation changes to (211) direction with Pr and Ta doping ratio increasing. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) analyses show that all films have uniform and homogenous nanoparticle distributions. Furthermore, morphologies of the films depend on the ratio between Pr and Ta dopants. From ultraviolet-visible (UV-Vis) spectrophotometer measurements, it is shown that the transmittance value of FTO film decreases with Pr and Ta doping elements increasing. The band gap value of FTO film increases only at 1 at.% Ta doping level, it drops off with Pr and Ta doping ratio increasing at other doped FTO films. The electrical measurements indicate that the sheet resistance value of FTO film initially decreases with Pr and Ta doping ratio decreasing and then it increases with Pr and Ta doping ratio increasing. The highest value of figure of merit is obtained for 1 at.% Ta- and Pr-doped FTO film. These results suggest that Pr- and Ta-doped FTO films may be appealing candidates for TCO applications. (paper)

Effect of a Ga-doped ZnO thin film with a ZTO buffer layer fabricated by using pulsed DC magnetron sputter for dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Song, Sang-Woo; Lee, Kyung-Ju; Roh, Ji-Hyung; Park, On-Jeon; Kim, Hwan-Sun; Moon, Byung-Moo [Korea University, Seoul (Korea, Republic of); Ji, Min-Woo [Yonsei University, Seoul (Korea, Republic of)

2014-08-15

The electrical property of a Ga-doped ZnO(GZO) thin film is well known to be similar that of commercialized fluorine-doped tin oxide(FTO). However GZO is limited for use at high process temperatures for solar cells because of its unstable resistivity at temperatures above 300 .deg. C. A GZO thin film compared to zinc tin oxide(ZTO)-GZO multilayer can be used at high process temperatures. A GZO thin film was deposited on glass by using pulsed DC magnetron sputter. Then, a ZTO buffer layer was deposited on the GZO surface. During the deposition, the working pressure was 5 mTorr (Z-1 glass) and 1 mTorr (Z-2 glass). Dye-sensitized solar cells (DSSCs) were fabricated using Z-1, Z-2 and commercialized FTO glasses. Z-2 showed a conversion efficiency of 4.265%, which was enhanced by 0.399% compared to that of the DSSCs using FTO(3.784%). The conversion efficiency for Z-1 (3.889%) was a little higher than that of FTO. Thus, the ZTO-GZO electrode showed better characteristics than those obtained using the FTO electrode, which can be attributed to the reduced charge recombination and series resistance.

Low-cost fabrication of WO{sub 3} films using a room temperature and low-vacuum air-spray based deposition system for inorganic electrochromic device applications

Energy Technology Data Exchange (ETDEWEB)

Park, Sung-Ik [Department of Mechanical and Aerospace Engineering, Seoul National University, Seoul (Korea, Republic of); Kim, Sooyeun, E-mail: sooyeunk@u.washington.edu [Department of Mechanical Engineering, University of Washington, Seattle, WA (United States); Choi, Jung-Oh; Song, Ji-Hyeon [Department of Mechanical and Aerospace Engineering, Seoul National University, Seoul (Korea, Republic of); Taya, Minoru [Department of Mechanical Engineering, University of Washington, Seattle, WA (United States); Ahn, Sung-Hoon, E-mail: ahnsh@snu.ac.kr [Department of Mechanical and Aerospace Engineering, Seoul National University, Seoul (Korea, Republic of); Institute of Advanced Machines and Design, Seoul (Korea, Republic of)

2015-08-31

We report the deposition of tungsten oxide (WO{sub 3}) thin films on fluorine-doped tin oxide (FTO) and indium-doped tin oxide (ITO) glass substrates by using a room-temperature deposition system based on low-vacuum air-spray for the fabrication of inorganic electrochromic windows. The structure of the WO{sub 3} films was characterized using X-ray diffraction, and the surface morphology and film thickness were investigated using scanning electron microscopy and atomic force microscopy. The color of the prepared WO{sub 3} films changed from slight yellow to dark blue under applied voltages, demonstrating electrochromism. The WO{sub 3} film coated FTO glass exhibited a large electrochromic contrast of up to 50% at a wavelength of 800 nm. The electrochemical properties of the films were examined using cyclic voltammetry and chronocoulometry. - Highlights: • WO{sub 3} thin films were fabricated using an air-spray based deposition system at room temperature under low-vacuum conditions. • Dry WO{sub 3} particles were directly deposited on FTO and ITO glasses by using a low-cost deposition system. • The FTO glass based WO{sub 3} film showed the optical contrast of 50% at a wavelength of 800 nm.

Enhanced performance of dye-sensitized solar cells using gold nanoparticles modified fluorine tin oxide electrodes

International Nuclear Information System (INIS)

Zhang Dingwen; Shen Jie; Huang Sumei; Wang Milton; Brolo, Alexandre G; Li Xiaodong

2013-01-01

We have investigated plasmon-assisted energy conversion in dye-sensitized solar cells (DSCs) applying gold nanoparticles (NPs) modified fluorine tin oxide (FTO) electrodes. A series of Au NPs with different sizes (15-80 nm) were synthesized and immobilized onto FTO glass slides. Photoanodes were prepared on these Au modified FTO substrates using P25 TiO 2 powders and by the screen-printing method. The size effects of Au NPs on the photovoltaic performance of the formed DSCs were investigated systematically. Structural and photoelectrochemical properties of the formed photoanodes were examined by field emission scanning electron microscopy and electrochemical impedance spectroscopy. It was found that the energy conversion efficiency of the DSC was highly dependent on the Au particle size. When the particle size was not greater than 60 nm, the DSC based on the Au NP-FTO composite electrode showed a higher short-circuit current density and better photovoltaic (PV) performance than the cell based on the bare FTO. The best cell was achieved using 25 nm sized Au NPs modified FTO. It exhibited a conversion efficiency of 6.69%, which was 15% higher than that of DSCs without Au NPs. The related PV performance enhancement mechanisms, photoelectrochemical processes and surface-plasmon resonances in DSCs with Au nanostructures are analysed and discussed.

The role of electric field during spray deposition on fluorine doped tin oxide film

Energy Technology Data Exchange (ETDEWEB)

Kumar, Anuj, E-mail: anujkumarom@gmail.com; Swami, Sanjay Kumar; Dutta, Viresh

2014-03-05

Highlights: • Fluorine doped tin oxide deposition by spray technique. • The growth reaction of tin oxide, controlled by the electric field on the substrate surface. • Deposit on large scale substrate 10 cm × 10 cm by single nozzle. • Obtained good quality of thin film. -- Abstract: The fluorine doped tin oxide film has been deposited on 10 cm × 10 cm glass substrate by using spray technique with a voltage applied between the nozzle and an annular electrode placed 2 mm below the nozzle. The effect of the electric field thus created during the spray deposition on structural, optical and electrical properties of SnO{sub 2}:F (FTO) film was studied. X-ray diffraction pattern revealed the presence of cassiterite structure with (2 0 0) orientation for all the FTO film. SEM study revealed the formation of smooth and uniform surface FTO film under the electric field over the entire substrate area. The electrical measurements show that the film prepared under the electric field (for an applied voltage of 2000 V) had a resistivity ∼1.2 × 10{sup −3} Ω cm, carrier concentration ∼4.21 × 10{sup 20} cm{sup −3} and mobility ∼14.48 cm{sup 2} V{sup −1} s{sup −1}. The sprayed FTO film have the average transmission in the visible region of more than about 80%.

Facile solution deposition of Cu{sub 2}ZnSnS{sub 4} (CZTS) nano-worm films on FTO substrates and its photoelectrochemical property

Energy Technology Data Exchange (ETDEWEB)

Huang, Yaohan; Li, Guangli; Fan, Qingfei; Zhang, Meili; Lan, Qi [School of Materials Science and Engineering, Southwest Jiaotong University, Key Laboratory of Advanced Technologies of Materials, Ministry of Education of China, Chengdu 610031 (China); Fan, Ximei, E-mail: fanximei@126.com [School of Materials Science and Engineering, Southwest Jiaotong University, Key Laboratory of Advanced Technologies of Materials, Ministry of Education of China, Chengdu 610031 (China); Zhou, Zuowan [School of Materials Science and Engineering, Southwest Jiaotong University, Key Laboratory of Advanced Technologies of Materials, Ministry of Education of China, Chengdu 610031 (China); Zhang, Chaoliang [State Key Laboratory of Oral Diseases, West China Hospital of Stomatology, Sichuan University, Chengdu, Sichuan 610041 (China)

2016-02-28

Graphical abstract: - Highlights: • Cu{sub 2}ZnSnS{sub 4} nanoworm thin films were synthesized directly on FTO substrates. • Polyethylene glycol-400 was used as solvent and structure-directing agent. • CZTS nanoworm film showed a photoelectrical conversion efficiency of 1.18%. - Abstract: In this work, Cu{sub 2}ZnSnS{sub 4} (CZTS) nanoworm films have been directly deposited on fluorine-doped tin oxide (FTO) conductive glass substrates by a solvothermal method using polyethylene glycol 400 (PEG-400) as the solvent and structure-directing agent. The as-obtained CZTS thin films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectrum (XPS), UV–vis spectra and photoelectrochemical measurement. The synthetic conditions, such as reaction temperature, reaction time, solvents, were investigated to know the formation of CZTS thin films. The results showed that PEG-400 plays a key role in the formation of the nanoworms by affecting the crystal growth process. The p-type CZTS nanoworm film with the band gap of 1.62 eV was synthesized at 180 °C for 22 h and the photovoltaic performance was studied by forming a photoelectrochemical cell.

Dye-sensitized solar cells based on different nano-oxides on plastic PET substrate

Science.gov (United States)

Mikula, Milan; Gemeiner, Pavol; Beková, Zuzana; Dvonka, Vladimír; Búc, Dalibor

2015-01-01

Polyethylene-terephthalate (PET) foils and glass slides coated with thin conductive layers were used as substrates for TiO2 or ZnO based photoactive electrodes of dye-sensitized solar cells (DSSC) with organo-metallic Ru-dye, standard iodine electrolyte and Pt coated FTO/glass counterelectrode (CE). Different compositions of nanoparticle oxides in forms of alcohol pastes as well as the CE paste were applied onto the substrates by screen printing or by doctor blade techniques. Photocurrents and I-V loading characteristics were measured depending on the solar cell structure and preparation, including the oxide composition, electrode conductivity and the dye type. The influence of thin TiO2 blocking layer prepared by sol-gel technique is also discussed.

FTO genetic variants, dietary intake and body mass index

DEFF Research Database (Denmark)

Qi, Qibin; Kilpeläinen, Tuomas O; Downer, Mary K

2014-01-01

FTO is the strongest known genetic susceptibility locus for obesity. Experimental studies in animals suggest the potential roles of FTO in regulating food intake. The interactive relation among FTO variants, dietary intake and body mass index (BMI) is complex and results from previous often small...

The Preparation and Property of Graphene /Tin Oxide Transparent Conductive Film

Directory of Open Access Journals (Sweden)

SUN Tao

2017-02-01

Full Text Available Graphene doped tin oxide composites were prepared with SnCIZ·2HZ 0 and graphene oxide as raw materials with sol-gel method and then spincoated on the quartz glass to manufacture a new transparent conductive film. The composite film was characterized with X-ray diffraction(XRDand scanning electron microscopy(SEM analysis. XRD results show that the graphene oxide was successfully prepared with Hummers method. The graphene layers and particulate SnOZ can be clearly observed in SEM photos. The transmittance and conductivity of the thin films were tested with ultraviolet visible spectrophotometer and Hall effect measurement. The results show that the transmittivity of composite film in visible region is more than 90% and surface square resistance is 41 S2/口.The graphene/ SnOZ film exhibits a higher performance in transparence and conductivity than commercial FTO glass.

Reduction-oxidation Enabled Glass-ceramics to Stainless Steel Bonding Part I: screening of doping oxidants

Energy Technology Data Exchange (ETDEWEB)

Dai, Steve Xunhu [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-09-01

Lithium silicate-based glass-ceramics with high coefficients of thermal expansion, designed to form matched hermetic seals in 304L stainless steel housing, show little evidence of interfacial chemical bonding, despite extensive inter-diffusion at the glass-ceramic-stainless steel (GC-SS) interface. A series of glass-ceramic compositions modified with a variety of oxidants, AgO, FeO, NiO, PbO, SnO, CuO, CoO, MoO₃ and WO₃, are examined for the feasibility of forming bonding oxides through reduction-oxidation (redox) at the GC-SS interface. The oxidants were selected according to their Gibbs free energy to allow for oxidation of Cr/Mn/Si from stainless steel, and yet to prevent a reduction of P2O5 in the glass-ceramic where the P₂O₅ is to form Li₃PO₄ nuclei for growth of high expansion crystalline SiO₂ phases. Other than the CuO and CoO modified glass-ceramics, bonding from interfacial redox reactions were not achieved in the modified glass-ceramics, either because of poor wetting on the stainless steel or a reduction of the oxidants at the surface of glass-ceramic specimens rather than the GC-SS interface.

Photoelastic response of permanently densified oxide glasses

Science.gov (United States)

Bechgaard, Tobias K.; Mauro, John C.; Thirion, Lynn M.; Rzoska, Sylwester J.; Bockowski, Michal; Smedskjaer, Morten M.

2017-05-01

The stress-induced birefringence (photoelastic response) in oxide glasses has important consequences for several applications, including glass for flat panel displays, chemically strengthened cover glass, and advanced optical glasses. While the effect of composition on the photoelastic response is relatively well documented, the effect of pressure has not been systematically studied. In this work, we evaluate the effect of hot isostatic compression on the photoelastic response of ten oxide glasses within two commonly used industrial glass families: aluminosilicates and boroaluminosilicates. Hot isostatic compression generally results in decreasing modifier-oxygen bond lengths and increasing network-former coordination numbers. These structural changes should lead to an increase in the stress optic coefficient (C) according to the model of Zwanziger et al., which can successfully predict the composition and structure dependence of C. However, in compressed glasses, we observe the opposite trend, viz., a decrease in the stress optic coefficient as a result of pressurization. We discuss this result based on measured changes in refractive index and elastic moduli within the context of atomic and lattice effects, building on the pioneering work of Mueller. We propose that the pressure-induced decrease in C is a result of changes in the shear modulus due to underlying topological changes in the glass network.

All-inorganic quantum-dot light-emitting-diodes with vertical nickel oxide nanosheets as hole transport layer

Directory of Open Access Journals (Sweden)

Jiahui Li

2016-10-01

Full Text Available All-inorganic quantum dot light emitting diodes (QLEDs have gained great attention as a result of their high stability under oxygen-rich, humid and high current working conditions. In this work, we have fabricated an all-inorganic QLED device (FTO/NiO/QDs/AZO/Ag with sandwich-structure, wherein the inorganic metal oxides thin films of NiO and AZO were employed as hole and electron transport layers, respectively. The porous NiO layer with vertical lamellar nanosheets interconnected microstructure have been directly synthesized on the substrate of conductive FTO glass and increased the wettability of CdSe@ZnS QDs, which result in an enhancement of current transport performance of the QLED.

Oxide glass structure evolution under swift heavy ion irradiation

International Nuclear Information System (INIS)

Mendoza, C.; Peuget, S.; Charpentier, T.; Moskura, M.; Caraballo, R.; Bouty, O.; Mir, A.H.; Monnet, I.; Grygiel, C.; Jegou, C.

2014-01-01

Highlights: • Structure of SHI irradiated glass is similar to the one of a hyper quenched glass. • D2 Raman band associated to 3 members ring is only observed in irradiated glass. • Irradiated state seems slightly different to an equilibrated liquid quenched rapidly. - Abstract: The effects of ion tracks on the structure of oxide glasses were examined by irradiating a silica glass and two borosilicate glass specimens containing 3 and 6 oxides with krypton ions (74 MeV) and xenon ions (92 MeV). Structural changes in the glass were observed by Raman and nuclear magnetic resonance spectroscopy using a multinuclear approach ( 11 B, 23 Na, 27 Al and 29 Si). The structure of irradiated silica glass resembles a structure quenched at very high temperature. Both borosilicate glass specimens exhibited depolymerization of the borosilicate network, a lower boron coordination number, and a change in the role of a fraction of the sodium atoms after irradiation, suggesting that the final borosilicate glass structures were quenched from a high temperature state. In addition, a sharp increase in the concentration of three membered silica rings and the presence of large amounts of penta- and hexacoordinate aluminum in the irradiated 6-oxide glass suggest that the irradiated glass is different from a liquid quenched at equilibrium, but it is rather obtained from a nonequilibrium liquid that is partially relaxed by very rapid quenching within the ion tracks

Large-scale fabrication of pseudocapacitive glass windows that combine electrochromism and energy storage.

Science.gov (United States)

Yang, Peihua; Sun, Peng; Chai, Zhisheng; Huang, Langhuan; Cai, Xiang; Tan, Shaozao; Song, Jinhui; Mai, Wenjie

2014-10-27

Multifunctional glass windows that combine energy storage and electrochromism have been obtained by facile thermal evaporation and electrodeposition methods. For example, WO3 films that had been deposited on fluorine-doped tin oxide (FTO) glass exhibited a high specific capacitance of 639.8 F g(-1). Their color changed from transparent to deep blue with an abrupt decrease in optical transmittance from 91.3% to 15.1% at a wavelength of 633 nm when a voltage of -0.6 V (vs. Ag/AgCl) was applied, demonstrating its excellent energy-storage and electrochromism properties. As a second example, a polyaniline-based pseudocapacitive glass was also developed, and its color can change from green to blue. A large-scale pseudocapacitive WO3-based glass window (15×15 cm(2)) was fabricated as a prototype. Such smart pseudocapacitive glass windows show great potential in functioning as electrochromic windows and concurrently powering electronic devices, such as mobile phones or laptops. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ferric oxide quantum dots in stable phosphate glass system and their magneto-optical study

Energy Technology Data Exchange (ETDEWEB)

Garaje, Sunil N.; Apte, Sanjay K. [Nanocomposite Group, Centre for Materials for Electronics Technology (C-MET), Department of Electronics and Information Technology (DeitY), Government of India, Panchawati, Off Pashan Road, Pune 411008 (India); Kumar, Ganpathy [Department of Electrical and Computer Engineering, Tennessee Technological University, 1 William L. Jones Drive, Cookeville, TN 38505 (United States); Panmand, Rajendra P.; Naik, Sonali D. [Nanocomposite Group, Centre for Materials for Electronics Technology (C-MET), Department of Electronics and Information Technology (DeitY), Government of India, Panchawati, Off Pashan Road, Pune 411008 (India); Mahajan, Satish M., E-mail: smahajan@tntech.edu [Department of Electrical and Computer Engineering, Tennessee Technological University, 1 William L. Jones Drive, Cookeville, TN 38505 (United States); Chand, Ramesh [Ministry of Communications and Information Technology, Department of Electronics and Information Technology (DeitY), Electronics Niketan, 6, CGO Complex, New Delhi 110003 (India); Kale, Bharat B., E-mail: bbkale@cmet.gov.in [Nanocomposite Group, Centre for Materials for Electronics Technology (C-MET), Department of Electronics and Information Technology (DeitY), Government of India, Panchawati, Off Pashan Road, Pune 411008 (India)

2013-02-15

Graphical abstract: We report synthesis of ferric oxide embedded low melting phosphate glass nanocomposite and also the effect of ferric oxide nanoparticles (NCs) content on the optical and magneto-optical properties of the glasses. Faraday rotation of the glass nanocomposites was measured and showed variation in Verdet constant with concentration of ferric oxide. Interestingly, the host glass itself showed fairly good Verdet constant (11.5°/T cm) and there is a threefold enhancement in the Verdet constant of ferric oxide quantum dot-glass nanocomposite. Highlights: ► We synthesize ferric oxide embedded low melting stable phosphate glass nanocomposite. ► Glasses doped with 0.25 and 2% ferric oxide show particle size in the range of 4–12 nm. ► The host phosphate glass itself shows fairly good Verdet constant (11.5°/T cm). ► Glasses doped with 0.25% ferric oxide show high Verdet constant (30.525°/T cm). ► The as synthesis glasses may have potential application in magneto optical devices. -- Abstract: Herein, we report the synthesis of ferric oxide embedded low melting phosphate glass nanocomposite and also the effect of ferric oxide nanoparticles content on the optical and magneto-optical properties of the glasses. The optical study clearly showed red shift in optical cut off with increasing ferric oxide concentration. The band gap of the host glass was observed to be 3.48 eV and it shifted to 3.14 eV after doping with ferric oxide. The glasses doped with 0.25 and 2% ferric oxide showed particle size of 4–6 nm and 8–12 nm, respectively. Faraday rotation of the glass nanocomposites was measured and showed variation in the Verdet constant as per increasing concentration of ferric oxide. Interestingly, the host glass itself showed fairly good Verdet constant (11.5°/T cm) and threefold enhancement was observed in the Verdet constant of ferric oxide quantum dot-glass nanocomposite.

A link between FTO, ghrelin, and impaired brain food-cue responsivity

Science.gov (United States)

Karra, Efthimia; O’Daly, Owen G.; Choudhury, Agharul I.; Yousseif, Ahmed; Millership, Steven; Neary, Marianne T.; Scott, William R.; Chandarana, Keval; Manning, Sean; Hess, Martin E.; Iwakura, Hiroshi; Akamizu, Takashi; Millet, Queensta; Gelegen, Cigdem; Drew, Megan E.; Rahman, Sofia; Emmanuel, Julian J.; Williams, Steven C.R.; Rüther, Ulrich U.; Brüning, Jens C.; Withers, Dominic J.; Zelaya, Fernando O.; Batterham, Rachel L.

2013-01-01

Polymorphisms in the fat mass and obesity-associated gene (FTO) are associated with human obesity and obesity-prone behaviors, including increased food intake and a preference for energy-dense foods. FTO demethylates N6-methyladenosine, a potential regulatory RNA modification, but the mechanisms by which FTO predisposes humans to obesity remain unclear. In adiposity-matched, normal-weight humans, we showed that subjects homozygous for the FTO “obesity-risk” rs9939609 A allele have dysregulated circulating levels of the orexigenic hormone acyl-ghrelin and attenuated postprandial appetite reduction. Using functional MRI (fMRI) in normal-weight AA and TT humans, we found that the FTO genotype modulates the neural responses to food images in homeostatic and brain reward regions. Furthermore, AA and TT subjects exhibited divergent neural responsiveness to circulating acyl-ghrelin within brain regions that regulate appetite, reward processing, and incentive motivation. In cell models, FTO overexpression reduced ghrelin mRNA N6-methyladenosine methylation, concomitantly increasing ghrelin mRNA and peptide levels. Furthermore, peripheral blood cells from AA human subjects exhibited increased FTO mRNA, reduced ghrelin mRNA N6-methyladenosine methylation, and increased ghrelin mRNA abundance compared with TT subjects. Our findings show that FTO regulates ghrelin, a key mediator of ingestive behavior, and offer insight into how FTO obesity-risk alleles predispose to increased energy intake and obesity in humans. PMID:23867619

A link between FTO, ghrelin, and impaired brain food-cue responsivity.

Science.gov (United States)

Karra, Efthimia; O'Daly, Owen G; Choudhury, Agharul I; Yousseif, Ahmed; Millership, Steven; Neary, Marianne T; Scott, William R; Chandarana, Keval; Manning, Sean; Hess, Martin E; Iwakura, Hiroshi; Akamizu, Takashi; Millet, Queensta; Gelegen, Cigdem; Drew, Megan E; Rahman, Sofia; Emmanuel, Julian J; Williams, Steven C R; Rüther, Ulrich U; Brüning, Jens C; Withers, Dominic J; Zelaya, Fernando O; Batterham, Rachel L

2013-08-01

Polymorphisms in the fat mass and obesity-associated gene (FTO) are associated with human obesity and obesity-prone behaviors, including increased food intake and a preference for energy-dense foods. FTO demethylates N6-methyladenosine, a potential regulatory RNA modification, but the mechanisms by which FTO predisposes humans to obesity remain unclear. In adiposity-matched, normal-weight humans, we showed that subjects homozygous for the FTO "obesity-risk" rs9939609 A allele have dysregulated circulating levels of the orexigenic hormone acyl-ghrelin and attenuated postprandial appetite reduction. Using functional MRI (fMRI) in normal-weight AA and TT humans, we found that the FTO genotype modulates the neural responses to food images in homeostatic and brain reward regions. Furthermore, AA and TT subjects exhibited divergent neural responsiveness to circulating acyl-ghrelin within brain regions that regulate appetite, reward processing, and incentive motivation. In cell models, FTO overexpression reduced ghrelin mRNA N6-methyladenosine methylation, concomitantly increasing ghrelin mRNA and peptide levels. Furthermore, peripheral blood cells from AA human subjects exhibited increased FTO mRNA, reduced ghrelin mRNA N6-methyladenosine methylation, and increased ghrelin mRNA abundance compared with TT subjects. Our findings show that FTO regulates ghrelin, a key mediator of ingestive behavior, and offer insight into how FTO obesity-risk alleles predispose to increased energy intake and obesity in humans.

The electronic conduction of glass and glass ceramics containing various transition metal oxides

International Nuclear Information System (INIS)

Yoshida, T.; Matsuno, Y.

1980-01-01

Nb 2 O 5 -V 2 O 5 -P 2 O 5 glasses containing only Group Va oxides have been investigated to elucidate their electronic conduction and structure, as compared with other glasses obtained by the addition of various transition metal oxides to vanadium phosphate. The P 2 O 5 introduction for Nb 2 O 5 in this glass with the same amount of V 2 O 5 increased the conductivity about two times. Glass ceramics having high conductivity increased by two orders of magnitude and the activation energy for conduction decreased from about 0.5 to 0.2 eV. The crystals were confirmed to be (V,Nb) 2 O 5 and Nb phosphate, one of which was highly conductive and developed a pillar-like shape with a length of more than 20 μm. (orig.)

Band alignment of TiO2/FTO interface determined by X-ray photoelectron spectroscopy: Effect of annealing

Directory of Open Access Journals (Sweden)

Haibo Fan

2016-01-01

Full Text Available The energy band alignment between pulsed-laser-deposited TiO2 and FTO was firstly characterized using high-resolution X-ray photoelectron spectroscopy. A valence band offset (VBO of 0.61 eV and a conduction band offset (CBO of 0.29 eV were obtained across the TiO2/FTO heterointerface. With annealing process, the VBO and CBO across the heterointerface were found to be -0.16 eV and 1.06 eV, respectively, with the alignment transforming from type-I to type-II. The difference in the band alignment is believed to be dominated by the core level down-shift of the FTO substrate, which is a result of the oxidation of Sn. Current-voltage test has verified that the band alignment has a significant effect on the current transport of the heterojunction.

Dietary intake, FTO genetic variants and adiposity

DEFF Research Database (Denmark)

Qi, Qibin; Downer, Mary K; Oskari Kilpeläinen, Tuomas

2015-01-01

The FTO gene harbors variation with the strongest effect on adiposity and obesity risk. Previous data support a role for FTO variation in influencing food intake. We conducted a combined analysis of 16,094 boys and girls aged 1–18 years from 14 studies to examine the following: 1) the association...

Hypothalamic FTO is associated with the regulation of energy intake not feeding reward

Directory of Open Access Journals (Sweden)

Radomska Katarzyna J

2009-10-01

Full Text Available Abstract Background Polymorphism in the FTO gene is strongly associated with obesity, but little is known about the molecular bases of this relationship. We investigated whether hypothalamic FTO is involved in energy-dependent overconsumption of food. We determined FTO mRNA levels in rodent models of short- and long-term intake of palatable fat or sugar, deprivation, diet-induced increase in body weight, baseline preference for fat versus sugar as well as in same-weight animals differing in the inherent propensity to eat calories especially upon availability of diverse diets, using quantitative PCR. FTO gene expression was also studied in organotypic hypothalamic cultures treated with anorexigenic amino acid, leucine. In situ hybridization (ISH was utilized to study FTO signal in reward- and hunger-related sites, colocalization with anorexigenic oxytocin, and c-Fos immunoreactivity in FTO cells at initiation and termination of a meal. Results Deprivation upregulated FTO mRNA, while leucine downregulated it. Consumption of palatable diets or macronutrient preference did not affect FTO expression. However, the propensity to ingest more energy without an effect on body weight was associated with lower FTO mRNA levels. We found that 4-fold higher number of FTO cells displayed c-Fos at meal termination as compared to initiation in the paraventricular and arcuate nuclei of re-fed mice. Moreover, ISH showed that FTO is present mainly in hunger-related sites and it shows a high degree of colocalization with anorexigenic oxytocin. Conclusion We conclude that FTO mRNA is present mainly in sites related to hunger/satiation control; changes in hypothalamic FTO expression are associated with cues related to energy intake rather than feeding reward. In line with that, neurons involved in feeding termination express FTO. Interestingly, baseline FTO expression appears linked not only with energy intake but also energy metabolism.

Milk: an epigenetic amplifier of FTO-mediated transcription? Implications for Western diseases.

Science.gov (United States)

Melnik, Bodo C

2015-12-21

Single-nucleotide polymorphisms within intron 1 of the FTO (fat mass and obesity-associated) gene are associated with enhanced FTO expression, increased body weight, obesity and type 2 diabetes mellitus (T2DM). The N (6) -methyladenosine (m(6)A) demethylase FTO plays a pivotal regulatory role for postnatal growth and energy expenditure. The purpose of this review is to provide translational evidence that links milk signaling with FTO-activated transcription of the milk recipient. FTO-dependent demethylation of m(6)A regulates mRNA splicing required for adipogenesis, increases the stability of mRNAs, and affects microRNA (miRNA) expression and miRNA biosynthesis. FTO senses branched-chain amino acids (BCAAs) and activates the nutrient sensitive kinase mechanistic target of rapamycin complex 1 (mTORC1), which plays a key role in translation. Milk provides abundant BCAAs and glutamine, critical components increasing FTO expression. CpG hypomethylation in the first intron of FTO has recently been associated with T2DM. CpG methylation is generally associated with gene silencing. In contrast, CpG demethylation generally increases transcription. DNA de novo methylation of CpG sites is facilitated by DNA methyltransferases (DNMT) 3A and 3B, whereas DNA maintenance methylation is controlled by DNMT1. MiRNA-29s target all DNMTs and thus reduce DNA CpG methylation. Cow´s milk provides substantial amounts of exosomal miRNA-29s that reach the systemic circulation and target mRNAs of the milk recipient. Via DNMT suppression, milk exosomal miRNA-29s may reduce the magnitude of FTO methylation, thereby epigenetically increasing FTO expression in the milk consumer. High lactation performance with increased milk yield has recently been associated with excessive miRNA-29 expression of dairy cow mammary epithelial cells (DCMECs). Notably, the galactopoietic hormone prolactin upregulates the transcription factor STAT3, which induces miRNA-29 expression. In a retrovirus-like manner

Band alignment of TiO{sub 2}/FTO interface determined by X-ray photoelectron spectroscopy: Effect of annealing

Energy Technology Data Exchange (ETDEWEB)

Fan, Haibo, E-mail: hbfan@nwu.edu.cn, E-mail: liusz@snnu.edu.cn [Key Laboratory of Applied Surface and Colloid Chemistry, National Ministry of Education, Shaanxi Engineering Lab for Advanced Energy Technology, School of Materials Science and Engineering, Shaanxi Normal University, Xi’an 710119 (China); School of Physics, Northwest University, Xi’an 710069 (China); Yang, Zhou; Ren, Xianpei; Gao, Fei [Key Laboratory of Applied Surface and Colloid Chemistry, National Ministry of Education, Shaanxi Engineering Lab for Advanced Energy Technology, School of Materials Science and Engineering, Shaanxi Normal University, Xi’an 710119 (China); Yin, Mingli [Key Laboratory of Applied Surface and Colloid Chemistry, National Ministry of Education, Shaanxi Engineering Lab for Advanced Energy Technology, School of Materials Science and Engineering, Shaanxi Normal University, Xi’an 710119 (China); School of Science, Xi’an Technological University, Xi’an, Shaanxi 710062 (China); Liu, Shengzhong, E-mail: hbfan@nwu.edu.cn, E-mail: liusz@snnu.edu.cn [Key Laboratory of Applied Surface and Colloid Chemistry, National Ministry of Education, Shaanxi Engineering Lab for Advanced Energy Technology, School of Materials Science and Engineering, Shaanxi Normal University, Xi’an 710119 (China); Dalian Institute of Chemical Physics, Dalian National Laboratory for Clean Energy, Chinese Academy of Sciences, Dalian, 116023 (China)

2016-01-15

The energy band alignment between pulsed-laser-deposited TiO{sub 2} and FTO was firstly characterized using high-resolution X-ray photoelectron spectroscopy. A valence band offset (VBO) of 0.61 eV and a conduction band offset (CBO) of 0.29 eV were obtained across the TiO{sub 2}/FTO heterointerface. With annealing process, the VBO and CBO across the heterointerface were found to be -0.16 eV and 1.06 eV, respectively, with the alignment transforming from type-I to type-II. The difference in the band alignment is believed to be dominated by the core level down-shift of the FTO substrate, which is a result of the oxidation of Sn. Current-voltage test has verified that the band alignment has a significant effect on the current transport of the heterojunction.

Enhanced photocatalytic performance of TiO{sub 2} nanotube based heterojunction photocatalyst via the coupling of graphene and FTO

Energy Technology Data Exchange (ETDEWEB)

Niu, Xiaoyou [College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Yu, Jianyuan [College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Department of Environmental and Chemical Engineering, Tangshan University, Tangshan 063000 (China); Wang, Likun; Fu, Chen; Wang, Jixia; Wang, Li [College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Zhao, Hongli, E-mail: zhaohongli@ysu.edu.cn [College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); State Key Laboratory of Metastable Materials Science and Technology, Qinhuangdao 066004 (China); Yang, Jingkai, E-mail: yangjk@ysu.edu.cn [National Defense Science and Technology, Yanshan University, Qinhuangdao 066004 (China)

2017-08-15

Highlights: • The rGO-TONT composites have been deposited onto FTO. • Photocatalytic reaction rate shows 3 times greater than TONT. • Chemical interaction between rGO and TONT was analyzed. • Electron transfer process in rGO-TONT/FTO heterojunction was discussed. - Abstract: The TiO{sub 2} nanotube (TONT) based heterojunction photocatalyst was developed via the coupling of reduced graphene oxide (rGO) and SnO{sub 2}:F film (FTO). Based on the characterization of Raman analysis, XRD, SEM, TEM, XPS and ESR, the crystal phase, morphology, heterojunction interfacial interaction and the photoinduced electron chemical environment of the samples are studied. In the photodegradation of methylene blue (MB) solution under UV irradiation, the rGO-TONT/FTO heterojunction photocatalyst exhibits the improved photocatalytic reaction rate, 3 times greater than that of pure TONT. The enhanced photocatalytic mechanism was discussed by PL. The effectively separate charge in heterojunction structure of rGO-TONT/FTO is responsible for the enhanced photocatalytic activity. Wherein, the abundant oxygen vacancies at TiO{sub 2} surface and the chemically bonded interface in rGO-TONT heterojunction also contributes to the interfacial electron transfer. Besides, the introduction of rGO enhanced its optical absorption capacity.

Effect of swift heavy ion (SHI) irradiation on transparent conducting oxide electrodes for dye-sensitized solar cell applications

International Nuclear Information System (INIS)

Singh, Hemant Kr.; Avasthi, D.K.; Aggarwal, Shruti

2015-01-01

Highlights: •The objective is to study the effect of swift heavy ion (SHI) irradiation on photoanode of DSSC for better efficiency. •This work presents the effect of SHI irradiation on various Transparent conducting oxides (TCOs). •Effects are studied in terms of conductivity and transmittance of TCOs. •ITO-PET gives best results in comparison to ITO and FTO for DSSC application under SHI irradiation. -- Abstract: Transparent conducting oxides (TCOs) are used as electrodes in dye-sensitized solar cells (DSSCs) because of their properties such as high transmittance and low resistivity. In the present work, the effects of swift heavy ion (SHI) irradiation on various types of TCOs are presented. The objective of this study is to investigate the effect of SHI on TCOs. For the present study, three different types of TCOs are considered, namely, (a) FTO (fluorine-doped tin oxide, SnO 2 :F) on a Nippon glass substrate, (b) ITO (indium tin oxide, In 2 O 3 :Sn) coated on polyethylene terephthalate (PET) on a Corning glass substrate, and (c) ITO on a Corning glass substrate. These films are irradiated with 120 MeV Ag +9 ions at fluences ranging from 3.0 × 10 11 ions/cm 2 to 3.0 × 10 13 ions/cm 2 . The structural, morphological, optical and electrical properties are studied via X-ray diffraction (XRD), atomic force microscopy (AFM), UV–Vis absorption spectroscopy and four-probe resistivity measurements, respectively. The ITO-PET electrode is found to exhibit superior conductivity and transmittance properties in comparison with the others after irradiation and, therefore, to be the most suitable for solar cell applications

Electrical and Optical Properties of Fluorine Doped Tin Oxide Thin Films Prepared by Magnetron Sputtering

Directory of Open Access Journals (Sweden)

Ziad Y. Banyamin

2014-10-01

Full Text Available Fluorine doped tin oxide (FTO coatings have been prepared using the mid-frequency pulsed DC closed field unbalanced magnetron sputtering technique in an Ar/O2 atmosphere using blends of tin oxide and tin fluoride powder formed into targets. FTO coatings were deposited with a thickness of 400 nm on glass substrates. No post-deposition annealing treatments were carried out. The effects of the chemical composition on the structural (phase, grain size, optical (transmission, optical band-gap and electrical (resistivity, charge carrier, mobility properties of the thin films were investigated. Depositing FTO by magnetron sputtering is an environmentally friendly technique and the use of loosely packed blended powder targets gives an efficient means of screening candidate compositions, which also provides a low cost operation. The best film characteristics were achieved using a mass ratio of 12% SnF2 to 88% SnO2 in the target. The thin film produced was polycrystalline with a tetragonal crystal structure. The optimized conditions resulted in a thin film with average visible transmittance of 83% and optical band-gap of 3.80 eV, resistivity of 6.71 × 10−3 Ω·cm, a carrier concentration (Nd of 1.46 × 1020 cm−3 and a mobility of 15 cm2/Vs.

FTO is a relevant factor for the development of the metabolic syndrome in mice.

Directory of Open Access Journals (Sweden)

Kathrin Ikels

Full Text Available The metabolic syndrome is a worldwide problem mainly caused by obesity. FTO was found to be a obesity-risk gene in humans and FTO deficiency in mice led to reduction in adipose tissue. Thus, FTO is an important factor for the development of obesity. Leptin-deficient mice are a well characterized model for analysing the metabolic syndrome. To determine the relevance of FTO for the development of the metabolic syndrome we analysed different parameters in combined homozygous deficient mice (Lep(ob/ob;Fto(-/-. Lep(ob/ob;Fto(-/- mice showed an improvement in analysed hallmarks of the metabolic syndrome in comparison to leptin-deficient mice wild type or heterozygous for Fto. Lep(ob/ob;Fto(-/- mice did not develop hyperglycaemia and showed an improved glucose tolerance. Furthermore, extension of beta-cell mass was prevented in Lep(ob/ob;Fto(-/-mice and accumulation of ectopic fat in the liver was reduced. In conclusion this study demonstrates that FTO deficiency has a protective effect not only on the development of obesity but also on the metabolic syndrome. Thus, FTO plays an important role in the development of metabolic disorders and is an interesting target for therapeutic agents.

FTO is expressed in neurones throughout the brain and its expression is unaltered by fasting.

Science.gov (United States)

McTaggart, James S; Lee, Sheena; Iberl, Michaela; Church, Chris; Cox, Roger D; Ashcroft, Frances M

2011-01-01

Single-nucleotide polymorphisms in the first intron of the ubiquitously expressed FTO gene are associated with obesity. Although the physiological functions of FTO remain unclear, food intake is often altered when Fto expression levels are manipulated. Furthermore, deletion of FTO from neurones alone has a similar effect on food intake to deletion of FTO in all tissues. These results indicate that FTO expression in the brain is particularly important. Considerable focus has been placed on the dynamic regulation of Fto mRNA expression in the hypothalamus after short-term (16-48 hour) fasting, but results have been controversial. There are no studies that quantify FTO protein levels across the brain, and assess its alteration following short-term fasting. Using immunohistochemistry, we found that FTO protein is widely expressed in mouse brain, and present in the majority of neurones. Using quantitative Western blotting and RT-qPCR we show that FTO protein and mRNA levels in the hypothalamus, cerebellum and rostral brain are relatively uniform, and levels in the brain are higher than in skeletal muscles of the lower limbs. Fasting for 18 hours does not alter the expression pattern, or levels, of FTO protein and mRNA. We further show that the majority of POMC neurones, which are critically involved in food intake regulation, also express FTO, but that the percentage of FTO-positive POMC neurones is not altered by fasting. In summary, we find no evidence that Fto/FTO expression is regulated by short-term (18-hour) fasting. Thus, it is unlikely that the hunger and increased post-fasting food intake caused by such food deprivation is driven by alterations in Fto/FTO expression. The widespread expression of FTO in neurones also suggests that physiological studies of this protein should not be limited to the hypothalamus.

FTO is expressed in neurones throughout the brain and its expression is unaltered by fasting.

Directory of Open Access Journals (Sweden)

James S McTaggart

Full Text Available Single-nucleotide polymorphisms in the first intron of the ubiquitously expressed FTO gene are associated with obesity. Although the physiological functions of FTO remain unclear, food intake is often altered when Fto expression levels are manipulated. Furthermore, deletion of FTO from neurones alone has a similar effect on food intake to deletion of FTO in all tissues. These results indicate that FTO expression in the brain is particularly important. Considerable focus has been placed on the dynamic regulation of Fto mRNA expression in the hypothalamus after short-term (16-48 hour fasting, but results have been controversial. There are no studies that quantify FTO protein levels across the brain, and assess its alteration following short-term fasting. Using immunohistochemistry, we found that FTO protein is widely expressed in mouse brain, and present in the majority of neurones. Using quantitative Western blotting and RT-qPCR we show that FTO protein and mRNA levels in the hypothalamus, cerebellum and rostral brain are relatively uniform, and levels in the brain are higher than in skeletal muscles of the lower limbs. Fasting for 18 hours does not alter the expression pattern, or levels, of FTO protein and mRNA. We further show that the majority of POMC neurones, which are critically involved in food intake regulation, also express FTO, but that the percentage of FTO-positive POMC neurones is not altered by fasting. In summary, we find no evidence that Fto/FTO expression is regulated by short-term (18-hour fasting. Thus, it is unlikely that the hunger and increased post-fasting food intake caused by such food deprivation is driven by alterations in Fto/FTO expression. The widespread expression of FTO in neurones also suggests that physiological studies of this protein should not be limited to the hypothalamus.

Oxidation feature and diffusion mechanism of Zr-based metallic glasses near the glass transition point

Science.gov (United States)

Hu, Zheng; Lei, Xianqi; Wang, Yang; Zhang, Kun

2018-03-01

The oxidation behaviors of as-cast, pre-deformed, and crystallized Zr47.9Ti0.3Ni3.1Cu39.3Al9.4 metallic glasses (MGs) were studied near the glass transition point. The oxidation kinetics of the crystallized MGs followed a parabolic-rate law, and the as-cast and pre-deformed MGs exerted a typical two-stage behavior above the glass transition temperature (T g). Most interesting, pre-deformed treatment can significantly improve the oxidation rate of MGs, as the initial oxidation appeared earlier than for the as-cast MGs, and was accompanied by much thicker oxide scale. The EDS and XPS results showed that the metal Al acted as the preferred scavenger that absorbed intrinsic oxygen in the near-surface region of as-cast MGs. However, a homogeneous mixed layer without Al was observed in the pre-deformed MGs. We speculated the accelerated diffusion of other elements in the MGs was due to the local increase in the free volume and significant shear-induced dilation of the local structure. The results from this study demonstrate that MGs exhibit controllable atomic diffusion during the oxidation process, which can facilitate use in super-cooled liquid region applications.

FTO polymorphisms moderate the association of food reinforcement with energy intake.

Science.gov (United States)

Scheid, Jennifer L; Carr, Katelyn A; Lin, Henry; Fletcher, Kelly D; Sucheston, Lara; Singh, Prashant K; Salis, Robbert; Erbe, Richard W; Faith, Myles S; Allison, David B; Epstein, Leonard H

2014-06-10

Food reinforcement (RRVfood) is related to increased energy intake, cross-sectionally related to obesity, and prospectively related to weight gain. The fat mass and obesity-associated (FTO) gene is related to elevated body mass index and increased energy intake. The primary purpose of the current study was to determine whether any of 68 FTO single nucleotide polymorphisms (SNPs) or a FTO risk score moderate the association between food reinforcement and energy or macronutrient intake. Energy and macronutrient intake was measured using a laboratory ad libitum snack food consumption task in 237 adults of varying BMI. Controlling for BMI, the relative reinforcing value of reading (RRVreading) and proportion of African ancestry, RRVfood predicted 14.2% of the variance in energy intake, as well as predicted carbohydrate, fat, protein and sugar intake. In individual analyses, six FTO SNPs (rs12921970, rs9936768, rs12446047, rs7199716, rs8049933 and rs11076022, spanning approximately 251kbp) moderated the relationship between RRVfood and energy intake to predict an additional 4.9-7.4% of variance in energy intake. We created an FTO risk score based on 5 FTO SNPs (rs9939609, rs8050136, rs3751812, rs1421085, and rs1121980) that are related to BMI in multiple studies. The FTO risk score did not increase variance accounted for beyond individual FTO SNPs. rs12921970 and rs12446047 served as moderators of the relationship between RRVfood and carbohydrate, fat, protein, and sugar intake. This study shows for the first time that the relationship between RRVfood and energy intake is moderated by FTO SNPs. Research is needed to understand how these processes interact to predict energy and macronutrient intake. Copyright © 2014 Elsevier Inc. All rights reserved.

Structural Properties of Zinc Oxide Nanorods Grown on Al-Doped Zinc Oxide Seed Layer and Their Applications in Dye-Sensitized Solar Cells

Directory of Open Access Journals (Sweden)

Kyung Ho Kim

2014-03-01

Full Text Available We fabricated zinc oxide (ZnO nanorods (NRs with Al-doped ZnO (AZO seed layers and dye-sensitized solar cells (DSSCs employed the ZnO NRs between a TiO2 photoelectrode and a fluorine-doped SnO2 (FTO electrode. The growth rate of the NRs was strongly dependent on the seed layer conditions, i.e., thickness, Al dopant and annealing temperature. Attaining a large particle size with a high crystallinity of the seed layer was vital to the well-aligned growth of the NRs. However, the growth was less related to the substrate material (glass and FTO coated glass. With optimized ZnO NRs, the DSSCs exhibited remarkably enhanced photovoltaic performance, because of the increase of dye absorption and fast carrier transfer, which, in turn, led to improved efficiency. The cell with the ZnO NRs grown on an AZO seed layer annealed at 350 °C showed a short-circuit current density (JSC of 12.56 mA/cm2, an open-circuit voltage (VOC of 0.70 V, a fill factor (FF of 0.59 and a power conversion efficiency (PCE, η of 5.20% under air mass 1.5 global (AM 1.5G illumination of 100 mW/cm2.

Loss of FTO antagonises Wnt signaling and leads to developmental defects associated with ciliopathies.

Directory of Open Access Journals (Sweden)

Daniel P S Osborn

Full Text Available Common intronic variants in the Human fat mass and obesity-associated gene (FTO are found to be associated with an increased risk of obesity. Overexpression of FTO correlates with increased food intake and obesity, whilst loss-of-function results in lethality and severe developmental defects. Despite intense scientific discussions around the role of FTO in energy metabolism, the function of FTO during development remains undefined. Here, we show that loss of Fto leads to developmental defects such as growth retardation, craniofacial dysmorphism and aberrant neural crest cells migration in Zebrafish. We find that the important developmental pathway, Wnt, is compromised in the absence of FTO, both in vivo (zebrafish and in vitro (Fto(-/- MEFs and HEK293T. Canonical Wnt signalling is down regulated by abrogated β-Catenin translocation to the nucleus whilst non-canonical Wnt/Ca(2+ pathway is activated via its key signal mediators CaMKII and PKCδ. Moreover, we demonstrate that loss of Fto results in short, absent or disorganised cilia leading to situs inversus, renal cystogenesis, neural crest cell defects and microcephaly in Zebrafish. Congruently, Fto knockout mice display aberrant tissue specific cilia. These data identify FTO as a protein-regulator of the balanced activation between canonical and non-canonical branches of the Wnt pathway. Furthermore, we present the first evidence that FTO plays a role in development and cilia formation/function.

Secondary electron emission characteristics of oxide electrodes in flat electron emission lamp

Directory of Open Access Journals (Sweden)

Chang-Lin Chiang

2016-01-01

Full Text Available The present study concerns with the secondary electron emission coefficient, γ, of the cathode materials used in the newly developed flat electron emission lamp (FEEL devices, which essentially integrates the concept of using cathode for fluorescent lamp and anode for cathode ray tube (CRT to obtain uniform planar lighting. Three different cathode materials, namely fluorine-doped tin oxide (FTO, aluminum oxide coated FTO (Al2O3/FTO and magnesium oxide coated FTO (MgO/FTO were prepared to investigate how the variations of γ and working gases influence the performance of FEEL devices, especially in lowering the breakdown voltage and pressure of the working gases. The results indicate that the MgO/FTO bilayer cathode exhibited a relatively larger effective secondary electron emission coefficient, resulting in significant reduction of breakdown voltage to about 3kV and allowing the device to be operated at the lower pressure to generate the higher lighting efficiency.

Secondary electron emission characteristics of oxide electrodes in flat electron emission lamp

Energy Technology Data Exchange (ETDEWEB)

Chiang, Chang-Lin, E-mail: CLChiang@itri.org.tw; Li, Chia-Hung [Green Energy and Environment Research Laboratories, Industrial Technology Research Institute, 195, Sec. 4, Chung Hsing Road, Chutung 310, Taiwan (China); Department of Electrophysics, National Chiao Tung University, 1001 Ta Hsueh Road, Hsinchu 300, Taiwan (China); Zeng, Hui-Kai [Department of Electronic Engineering, Chung Yuan Christian University, 200 Chung Pei Road, Chung Li 320, Taiwan (China); Li, Jung-Yu, E-mail: JY-Lee@itri.org.tw; Chen, Shih-Pu; Lin, Yi-Ping [Green Energy and Environment Research Laboratories, Industrial Technology Research Institute, 195, Sec. 4, Chung Hsing Road, Chutung 310, Taiwan (China); Hsieh, Tai-Chiung; Juang, Jenh-Yih, E-mail: jyjuang@cc.nctu.edu.tw [Department of Electrophysics, National Chiao Tung University, 1001 Ta Hsueh Road, Hsinchu 300, Taiwan (China)

2016-01-15

The present study concerns with the secondary electron emission coefficient, γ, of the cathode materials used in the newly developed flat electron emission lamp (FEEL) devices, which essentially integrates the concept of using cathode for fluorescent lamp and anode for cathode ray tube (CRT) to obtain uniform planar lighting. Three different cathode materials, namely fluorine-doped tin oxide (FTO), aluminum oxide coated FTO (Al{sub 2}O{sub 3}/FTO) and magnesium oxide coated FTO (MgO/FTO) were prepared to investigate how the variations of γ and working gases influence the performance of FEEL devices, especially in lowering the breakdown voltage and pressure of the working gases. The results indicate that the MgO/FTO bilayer cathode exhibited a relatively larger effective secondary electron emission coefficient, resulting in significant reduction of breakdown voltage to about 3kV and allowing the device to be operated at the lower pressure to generate the higher lighting efficiency.

Composition-structure-property relation of oxide glasses

DEFF Research Database (Denmark)

Hermansen, Christian

also increases such properties. Yet, these rules are not strictly followed even for the simplest binary oxide glasses, such as alkali silicates, borates and phosphates. In this thesis it is argued that the missing link between composition and properties is the glass structure. Structural models...... are proposed based on topological selection rules and experimentally verified. The relation between structure and properties is evaluated using topological constraint theory, which in its essence is a theory that quantifies the two intuitions of the glass scientist. The end result is a quantitative model...

Surfactant-assisted ultrasonic spray pyrolysis of nickel oxide and lithium-doped nickel oxide thin films, toward electrochromic applications

Energy Technology Data Exchange (ETDEWEB)

Denayer, Jessica [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium); Bister, Geoffroy [Environmental and Material Research Association (CRIBC-INISMa), avenue gouverneur cornez 4, 7000 Mons (Belgium); Simonis, Priscilla [Laboratory LPS, University of Namur, rue de bruxelles 61, 5000 Namur (Belgium); Colson, Pierre; Maho, Anthony [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium); Aubry, Philippe [Environmental and Material Research Association (CRIBC-INISMa), avenue gouverneur cornez 4, 7000 Mons (Belgium); Vertruyen, Bénédicte [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium); Henrist, Catherine, E-mail: catherine.henrist@ulg.ac.be [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium); Lardot, Véronique; Cambier, Francis [Environmental and Material Research Association (CRIBC-INISMa), avenue gouverneur cornez 4, 7000 Mons (Belgium); Cloots, Rudi [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium)

2014-12-01

Highlights: • Surfactant-assisted USP: a novel and low cost process to obtain high quality nickel oxide films, with or without lithium dopant. • Increased uniformity and reduced light scattering thanks to the addition of a surfactant. • Improved electrochromic performance (coloration efficiency and contrast) for lithium-doped films by comparison with the undoped NiO film. - Abstract: Lithium-doped nickel oxide and undoped nickel oxide thin films have been deposited on FTO/glass substrates by a surfactant-assisted ultrasonic spray pyrolysis. The addition of polyethylene glycol in the sprayed solution has led to improved uniformity and reduced light scattering compared to films made without surfactant. Furthermore, the presence of lithium ions in NiO films has resulted in improved electrochromic performances (coloration contrast and efficiency), but with a slight decrease of the electrochromic switching kinetics.

The Obesity-Associated FTO Gene Encodes a 2-Oxoglutarate–Dependent Nucleic Acid Demethylase

Science.gov (United States)

Gerken, Thomas; Girard, Christophe A.; Tung, Yi-Chun Loraine; Webby, Celia J.; Saudek, Vladimir; Hewitson, Kirsty S.; Yeo, Giles S. H.; McDonough, Michael A.; Cunliffe, Sharon; McNeill, Luke A.; Galvanovskis, Juris; Rorsman, Patrik; Robins, Peter; Prieur, Xavier; Coll, Anthony P.; Ma, Marcella; Jovanovic, Zorica; Farooqi, I. Sadaf; Sedgwick, Barbara; Barroso, Inês; Lindahl, Tomas; Ponting, Chris P.; Ashcroft, Frances M.; O'Rahilly, Stephen; Schofield, Christopher J.

2009-01-01

Variants in the FTO (fat mass and obesity associated) gene are associated with increased body mass index in humans. Here, we show by bioinformatics analysis that FTO shares sequence motifs with Fe(II)- and 2-oxoglutarate–dependent oxygenases. We find that recombinant murine Fto catalyzes the Fe(II)- and 2OG-dependent demethylation of 3-methylthymine in single-stranded DNA, with concomitant production of succinate, formaldehyde, and carbon dioxide. Consistent with a potential role in nucleic acid demethylation, Fto localizes to the nucleus in transfected cells. Studies of wild-type mice indicate that Fto messenger RNA (mRNA) is most abundant in the brain, particularly in hypothalamic nuclei governing energy balance, and that Fto mRNA levels in the arcuate nucleus are regulated by feeding and fasting. Studies can now be directed toward determining the physiologically relevant FTO substrate and how nucleic acid methylation status is linked to increased fat mass. PMID:17991826

Glass science tutorial: Lecture number-sign 1, Chemistry and properties of oxide glasses. Professor William C. LaCourse, Lecturer

International Nuclear Information System (INIS)

Kruger, A.A.

1994-10-01

The tutorial covers the following topics: Definitions and terminology; Introduction to glass structure and properties; The glass transition; Structure/property relationships in oxide glasses; Generalized models for predicting structure/properties; Glass surfaces; Chemical durability; and Mechanical properties

Effect of swift heavy ion (SHI) irradiation on transparent conducting oxide electrodes for dye-sensitized solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Singh, Hemant Kr. [University School of Basic and Applied Sciences, Guru Gobind Singh Indraprastha University, New Delhi (India); Avasthi, D.K. [Inter University Accelerator Center, Post Box 10502, New Delhi (India); Aggarwal, Shruti, E-mail: shruti.al@gmail.com [University School of Basic and Applied Sciences, Guru Gobind Singh Indraprastha University, New Delhi (India)

2015-06-15

Highlights: •The objective is to study the effect of swift heavy ion (SHI) irradiation on photoanode of DSSC for better efficiency. •This work presents the effect of SHI irradiation on various Transparent conducting oxides (TCOs). •Effects are studied in terms of conductivity and transmittance of TCOs. •ITO-PET gives best results in comparison to ITO and FTO for DSSC application under SHI irradiation. -- Abstract: Transparent conducting oxides (TCOs) are used as electrodes in dye-sensitized solar cells (DSSCs) because of their properties such as high transmittance and low resistivity. In the present work, the effects of swift heavy ion (SHI) irradiation on various types of TCOs are presented. The objective of this study is to investigate the effect of SHI on TCOs. For the present study, three different types of TCOs are considered, namely, (a) FTO (fluorine-doped tin oxide, SnO{sub 2}:F) on a Nippon glass substrate, (b) ITO (indium tin oxide, In{sub 2}O{sub 3}:Sn) coated on polyethylene terephthalate (PET) on a Corning glass substrate, and (c) ITO on a Corning glass substrate. These films are irradiated with 120 MeV Ag{sup +9} ions at fluences ranging from 3.0 × 10{sup 11} ions/cm{sup 2} to 3.0 × 10{sup 13} ions/cm{sup 2}. The structural, morphological, optical and electrical properties are studied via X-ray diffraction (XRD), atomic force microscopy (AFM), UV–Vis absorption spectroscopy and four-probe resistivity measurements, respectively. The ITO-PET electrode is found to exhibit superior conductivity and transmittance properties in comparison with the others after irradiation and, therefore, to be the most suitable for solar cell applications.

Electrochemistry behavior of endogenous thiols on fluorine doped tin oxide electrodes

Energy Technology Data Exchange (ETDEWEB)

Rojas, Luciana; Molero, Leonard; Tapia, Ricardo A.; Rio, Rodrigo del; Valle, M. Angelica del; Antilen, Monica [Departamento de Quimica Inorganica, Facultad de Quimica, Pontificia Universidad Catolica de Chile, Av Vicuna Mackenna 4860, Casilla 306, Correo 22, Macul, Santiago (Chile); Armijo, Francisco, E-mail: jarmijom@uc.cl [Departamento de Quimica Inorganica, Facultad de Quimica, Pontificia Universidad Catolica de Chile, Av Vicuna Mackenna 4860, Casilla 306, Correo 22, Macul, Santiago (Chile)

2011-10-01

Highlights: > The first time that fluorine doped tin oxide electrodes are used for the electrooxidation of endogenous thiols. > Low potentials of electrooxidation were obtained for the different thiols. > The electrochemical behavior of thiols depends on the pH and the ionic electroactive species, the electrooxidation proceeds for a process of adsorption of electroactive species on FTO and high values the heterogeneous electron tranfer rate constant of the reaction were obtained. - Abstract: In this work the electrochemical behavior of different thiols on fluorine doped tin oxide (FTO) electrodes is reported. To this end, the mechanism of electrochemical oxidation of glutathione (GSH), cysteine (Cys), homocysteine (HCys) and acetyl-cysteine (ACys) at different pH was investigated. FTO showed electroactivity for the oxidation of the first three thiols at pH between 2.0 and 4.0, but under these conditions no acetyl-cysteine oxidation was observed on FTO. Voltammetric studies of the electro-oxidation of GSH, Cys and HCys showed peaks at about 0.35, 0.29, and 0.28 V at optimum pH 2.4, 2.8 and 3.4, respectively. In addition, this study demonstrated that GSH, Cys and HCys oxidation occurs when the zwitterion is the electro-active species that interact by adsorption on FTO electrodes. The overall reaction involves 4e{sup -}/4H{sup +} and 2e{sup -}/2H{sup +}, respectively, for HCys and for GSH and Cys and high heterogeneous electron transfer rate constants. Besides, the use of FTO for the determination of different thiols was evaluated. Experimental square wave voltammetry shows a linear current vs. concentrations response between 0.1 and 1.0 mM was found for HCys and GSH, indicating that these FTO electrodes are promising candidates for the efficient electrochemical determination of these endogenous thiols.

Optical and mechanical anisotropy of oxide glass fibers

DEFF Research Database (Denmark)

Deubener, J.; Yue, Yuanzheng

2012-01-01

products [1], whereas stretching (frozen-in strain) results in optical and mechanical anisotropy of glass fibers, which is quantified inter alia by the specific birefringence [2]. The paper will stress the later effects by combining previous results on the structural origins of birefringence...... and anisotropic shrinkage in silica and phosphate fibers with recent studies on relaxation of optical anisotropy in E-glass fibers [3,4].......Upon fiber drawing, glass forming oxide melts are thermally quenched and mechanically stretched. High cooling rates (up to 106 K/min) of quenched glass fibres lead to higher enthalpy state of liquids, thereby, to higher fictive temperature than regular quenching (e.g. 20 K/min) of bulk glass...

Fto colocalizes with a satiety mediator oxytocin in the brain and upregulates oxytocin gene expression

Energy Technology Data Exchange (ETDEWEB)

Olszewski, Pawel K., E-mail: olsze005@umn.edu [Department of Neuroscience, Functional Pharmacology, Uppsala University, 75124 Uppsala (Sweden); Minnesota Obesity Center, Saint Paul, MN 55108 (United States); Fredriksson, Robert; Eriksson, Jenny D. [Department of Neuroscience, Functional Pharmacology, Uppsala University, 75124 Uppsala (Sweden); Mitra, Anaya [Department of Food Science and Nutrition, Saint Paul, MN 55108 (United States); Radomska, Katarzyna J. [Department of Neuroscience, Functional Pharmacology, Uppsala University, 75124 Uppsala (Sweden); Gosnell, Blake A. [Department of Food Science and Nutrition, Saint Paul, MN 55108 (United States); Solvang, Maria N. [Department of Neuroscience, Functional Pharmacology, Uppsala University, 75124 Uppsala (Sweden); Levine, Allen S. [Minnesota Obesity Center, Saint Paul, MN 55108 (United States); Department of Food Science and Nutrition, Saint Paul, MN 55108 (United States); Schioeth, Helgi B. [Department of Neuroscience, Functional Pharmacology, Uppsala University, 75124 Uppsala (Sweden)

2011-05-13

Highlights: {yields} The majority of neurons synthesizing a satiety mediator, oxytocin, coexpress Fto. {yields} The level of colocalization is similar in the male and female brain. {yields} Fto overexpression in hypothalamic neurons increases oxytocin mRNA levels by 50%. {yields} Oxytocin does not affect Fto expression through negative feedback mechanisms. -- Abstract: Single nucleotide polymorphisms in the fat mass and obesity-associated (FTO) gene have been associated with obesity in humans. Alterations in Fto expression in transgenic animals affect body weight, energy expenditure and food intake. Fto, a nuclear protein and proposed transcription co-factor, has been speculated to affect energy balance through a functional relationship with specific genes encoding feeding-related peptides. Herein, we employed double immunohistochemistry and showed that the majority of neurons synthesizing a satiety mediator, oxytocin, coexpress Fto in the brain of male and female mice. We then overexpressed Fto in a murine hypothalamic cell line and, using qPCR, detected a 50% increase in the level of oxytocin mRNA. Expression levels of several other feeding-related genes, including neuropeptide Y (NPY) and Agouti-related protein (AgRP), were unaffected by the FTO transfection. Addition of 10 and 100 nmol oxytocin to the cell culture medium did not affect Fto expression in hypothalamic cells. We conclude that Fto, a proposed transcription co-factor, influences expression of the gene encoding a satiety mediator, oxytocin.

Fto colocalizes with a satiety mediator oxytocin in the brain and upregulates oxytocin gene expression

International Nuclear Information System (INIS)

Olszewski, Pawel K.; Fredriksson, Robert; Eriksson, Jenny D.; Mitra, Anaya; Radomska, Katarzyna J.; Gosnell, Blake A.; Solvang, Maria N.; Levine, Allen S.; Schioeth, Helgi B.

2011-01-01

Highlights: → The majority of neurons synthesizing a satiety mediator, oxytocin, coexpress Fto. → The level of colocalization is similar in the male and female brain. → Fto overexpression in hypothalamic neurons increases oxytocin mRNA levels by 50%. → Oxytocin does not affect Fto expression through negative feedback mechanisms. -- Abstract: Single nucleotide polymorphisms in the fat mass and obesity-associated (FTO) gene have been associated with obesity in humans. Alterations in Fto expression in transgenic animals affect body weight, energy expenditure and food intake. Fto, a nuclear protein and proposed transcription co-factor, has been speculated to affect energy balance through a functional relationship with specific genes encoding feeding-related peptides. Herein, we employed double immunohistochemistry and showed that the majority of neurons synthesizing a satiety mediator, oxytocin, coexpress Fto in the brain of male and female mice. We then overexpressed Fto in a murine hypothalamic cell line and, using qPCR, detected a 50% increase in the level of oxytocin mRNA. Expression levels of several other feeding-related genes, including neuropeptide Y (NPY) and Agouti-related protein (AgRP), were unaffected by the FTO transfection. Addition of 10 and 100 nmol oxytocin to the cell culture medium did not affect Fto expression in hypothalamic cells. We conclude that Fto, a proposed transcription co-factor, influences expression of the gene encoding a satiety mediator, oxytocin.

Bismuth silicate glass containing heavy metal oxide as a promising radiation shielding material

Science.gov (United States)

Elalaily, Nagia A.; Abou-Hussien, Eman M.; Saad, Ebtisam A.

2016-12-01

Optical and FTIR spectroscopic measurements and electron paramagnetic resonance (EPR) properties have been utilized to investigate and characterize the given compositions of binary bismuth silicate glasses. In this work, it is aimed to study the possibility of using the prepared bismuth silicate glasses as a good shielding material for γ-rays in which adding bismuth oxide to silicate glasses causes distinguish increase in its density by an order of magnitude ranging from one to two more than mono divalent oxides. The good thermal stability and high density of the bismuth-based silicate glass encourage many studies to be undertaken to understand its radiation shielding efficiency. For this purpose a glass containing 20% bismuth oxide and 80% SiO2 was prepared using the melting-annealing technique. In addition the effects of adding some alkali heavy metal oxides to this glass, such as PbO, BaO or SrO, were also studied. EPR measurements show that the prepared glasses have good stability when exposed to γ-irradiation. The changes in the FTIR spectra due to the presence of metal oxides were referred to the different housing positions and physical properties of the respective divalent Sr2+, Ba2+ and Pb2+ ions. Calculations of optical band gap energies were presented for some selected glasses from the UV data to support the probability of using these glasses as a gamma radiation shielding material. The results showed stability of both optical and magnetic spectra of the studied glasses toward gamma irradiation, which validates their irradiation shielding behavior and suitability as the radiation shielding candidate materials.

Mechanical Properties of Glass Surfaces Coated with Tin Oxide

DEFF Research Database (Denmark)

Swindlehurst, W. E.; Cantor, B.

1978-01-01

The effect of tin oxide coatings on the coefficient of friction and fracture strength of glass surfaces is studied. Experiments were performed partly on commercially treated glass bottles and partly on laboratory prepared microscope slides. Coatings were applied in the laboratory by decomposition...

Association of FTO Polymorphisms with Early Age of Obesity in Obese Italian Subjects

Directory of Open Access Journals (Sweden)

Federica Sentinelli

2012-01-01

Aims of our study are to investigate: (1 the association of FTO gene SNPs rs9939609 and rs9930506 with body mass index (BMI and obesity-related parameters in a large cohort (n=752 of Italian obese subjects; (2 the association between the two FTO SNPs and age of onset of obesity. Our results demonstrate a strong association between FTO SNPs rs9939609 (P<0.043 and rs9930506 (P<0.029 with BMI in the Italian population. FTO rs9930506 was significantly associated with higher BMI in a G allele dose-dependent manner (BMI+1.4 kg/m2 per G allele. We also observed that the association with BMI of the two FTO variants varied with age, with the carriers of the risk alleles developing an increase in body weight earlier in life. In conclusion, our study further demonstrates a role of the genetic variability in FTO on BMI in a large Italian population.

FTO genotype is associated with exercise training-induced changes in body composition

Science.gov (United States)

Rankinen, Tuomo; Rice, Treva; Teran-Garcia, Margarita; Rao, D.C.; Bouchard, Claude

2010-01-01

The fat mass and obesity associated (FTO) gene is the first obesity-susceptibility gene identified by genome-wide association scans and confirmed in several follow-up studies. Homozygotes for the risk allele (A/A) have 1.67 times greater risk of obesity than those who do not have the allele. However, it is not known if regular exercise-induced changes in body composition are influenced by the FTO genotype. The purpose of our study was to test if the FTO genotype is associated with exercise-induced changes in adiposity. Body composition was derived from underwater weighing before and after a 20-week endurance training program in 481 previously sedentary white subjects of the HERITAGE Family Study. FTO SNP rs8050136 was genotyped using Illumina GoldenGate assay. In the sedentary state, the A/A homozygotes were significantly heavier and fatter than the heterozygotes and the C/C homozygotes in men (p=0.004) but not in women (p=0.331; gene-by-sex interaction p=0.0053). The FTO genotype was associated with body fat responses to regular exercise (p<0.005; adjusted for age, sex, and baseline value of response trait): carriers of the C-allele showed three times greater fat mass and %body fat losses than the A/A homozygotes. The FTO genotype explained 2% of the variance in adiposity changes. Our data suggest that the FTO obesity-susceptibility genotype influences the body fat responses to regular exercise. Resistance to exercise-induced reduction in total adiposity may represent one mechanism by which the FTO A allele promotes overweight and obesity. PMID:19543202

Loss of FTO in adipose tissue decreases Angptl4 translation and alters triglyceride metabolism.

Science.gov (United States)

Wang, Chao-Yung; Shie, Shian-Sen; Wen, Ming-Shien; Hung, Kuo-Chun; Hsieh, I-Chang; Yeh, Ta-Sen; Wu, Delon

2015-12-15

A common variant of the FTO (fat mass- and obesity-associated) gene is a risk factor for obesity. We found that mice with an adipocyte-specific deletion of FTO gained more weight than control mice on a high-fat diet. Analysis of mice lacking FTO in adipocytes fed a normal diet or adipocytes from these mice revealed alterations in triglyceride metabolism that would be expected to favor increased fatty acid storage by adipose tissue. Mice lacking FTO in adipocytes showed increased serum triglyceride breakdown and clearance, which was associated with lower serum triglyceride concentrations. In addition, lipolysis in response to β-adrenergic stimulation was decreased in adipocytes and ex vivo adipose explants from the mutant mice. FTO is a nucleic acid demethylase that removes N(6)-methyladenosine (m(6)A) from mRNAs. We found that FTO bound to Angptl4, which encodes an adipokine that stimulates intracellular lipolysis in adipocytes. Unexpectedly, the adipose tissue of fasted or fed mice lacking FTO in adipocytes had greater Angptl4 mRNA abundance. However, after high-fat feeding, the mutant mice had less Angptl4 protein and more m(6)A-modified Angptl4 than control mice, suggesting that lack of FTO prevented the translation of Angptl4. Injection of Angptl4-encoding adenovirus into mice lacking FTO in adipocytes restored serum triglyceride concentrations and lipolysis to values similar to those in control mice and abolished excessive weight gain from a high-fat diet. These results reveal that FTO regulates fatty acid mobilization in adipocytes and thus body weight in part through posttranscriptional regulation of Angptl4. Copyright © 2015, American Association for the Advancement of Science.

Microstructured fibers with high lanthanum oxide glass core for nonlinear applications

Science.gov (United States)

Kobelke, J.; Schuster, K.; Litzkendorf, D.; Schwuchow, A.; Kirchhof, J.; Bartelt, H.; Tombelaine, V.; Leproux, P.; Couderc, V.; Labruyere, A.

2009-05-01

We demonstrate a low loss microstructured fiber (MOF) with a high nonlinear glass core and silica holey cladding. The substitution of mostly used silica as core material of microstructured fibers by lanthanum oxide glass promises a high nonlinear conversion efficiency for supercontinuum (SC) generation. The glass composition is optimized in terms of thermochemical and optical requirements. The glass for the MOF core has a high lanthanum oxide concentration (10 mol% La2O3) and a good compatibility with the silica cladding. This is performed by adding a suitable alumina concentration up to 20 mol%. The lanthanum oxide glass preform rods were manufactured by melting technique. Besides purity issues the material homogeneity plays an important role to achieve low optical loss. The addition of fluorides allows the better homogenization of the glass composition in the preform volume by refining. The minimum attenuation of an unstructured fiber drawn from this glass is about 0.6 dB/m. It is mostly caused by decreasing of scattering effects. The microstructured silica cladding allows the considerable shifting of dispersive behavior of the MOF for an optimal pump light conversion. The MOF shows zero dispersion wavelengths (ZDW) of 1140 nm (LP01 mode) and 970 nm (LP11 mode). The supercontinuum generation was investigated with a 1064 nm pump laser (650 ps). It shows a broad band emission between 500 nm and 2200 nm.

Microstructure and magnetic properties of yttrium alumina silicate glass microspheres containing iron oxide

International Nuclear Information System (INIS)

Sharma, K.; Basak, C.B.; Prajapat, C.L.; Singh, M.R.

2015-01-01

Yttrium alumino-silicate glass microspheres have been used for localized delivery of high radiation dose to tissues in the treatment of hepatocellular carcinoma (BCC) and synovitis. 90 Y is a pure beta emitter with beta emission energy of 0.9367 MeV, average penetration range in tissue 2.5 mm, physical half-life of 64.2 h, thus an effective radioisotope for delivering high radiation dose to the tumor. The efficacy of radiotherapy can further be improved if the glass microspheres are doped with magnetic particles for targeted delivery of high radiation dose. Magnetic glass microspheres can also be utilized for cancer treatment using the magnetic heating of tumor cell. The magnetic glass microspheres are obtained from the glasses with nominal composition (64-x) SiO 2 -17Y 2 O 3 -19 Al 2 O 3 -xFe 2 O 3 (x=4-16 mol %). Density of glasses increases from 3.5g/cc to 3.8g/cc as iron oxide content is increased from 4 to 16 mol %. The glass transition temperature and peak crystallization temperature decreases as the iron oxide content increases. T g values of glass samples decreases with increase of Fe 2 O 3 , while SiO 2 content is decreased. SiO 2 is a network forming oxide and a decrease in the network former in glass lead to decrease in thermo-physical properties like T g . The development of ferrimagnetic crystallites in glasses arise from the conversion of iron oxide into magnetite, magnemite and hematite, which is influenced by the structural and ordering of magnetic particles. The microstructure of glass-ceramic exhibited the formation of 50-100 nm size particles. The magnetite and hematite are formed as major crystalline phases. The magnetization values increased with an increase of iron oxide content and attributed to formation of magnetite phase. Results have shown that the glass microspheres with magnetic properties can be used as potential materials for cancer treatment. (author)

Synthesis of p-type nickel oxide nanosheets on n-type titanium dioxide nanorod arrays for p-n heterojunction-based UV photosensor

Science.gov (United States)

Yusoff, M. M.; Mamat, M. H.; Malek, M. F.; Abdullah, M. A. R.; Ismail, A. S.; Saidi, S. A.; Mohamed, R.; Suriani, A. B.; Khusaimi, Z.; Rusop, M.

2018-05-01

Titanium dioxide (TiO2) nanorod arrays (TNAs) were synthesized and deposited on fluorine tin oxide (FTO)-coated glass substrate using a novel and facile immersion method in a glass container. The synthesis and deposition of p-type nickel oxide (NiO) nanosheets (NS) on the n-type TNAs was investigated in the p-n heterojunction photodiode (PD) for the application of ultraviolet (UV) photosensor. The fabricated TNAs/NiO NS based UV photosensor exhibited a highly increased photocurrent of 4.3 µA under UV radiation (365 nm, 750 µW/cm2) at 1.0 V reverse bias. In this study, the fabricated TNAs/NiO NS p-n heterojunction based photodiode showed potential applications for UV photosensor based on the stable photo-generated current attained under UV radiation.

Designing porous metallic glass compact enclosed with surface iron oxides

Energy Technology Data Exchange (ETDEWEB)

Cho, Jae Young; Park, Hae Jin; Hong, Sung Hwan; Kim, Jeong Tae; Kim, Young Seok; Park, Jun-Young; Lee, Naesung [Hybrid Materials Center (HMC), Faculty of Nanotechnology and Advanced Materials Engineering, Sejong University, 209 Neungdong-ro, Gwangjin-gu, Seoul 143-747 (Korea, Republic of); Seo, Yongho [Graphene Research Institute (GRI) & HMC, Faculty of Nanotechnology and Advanced Materials Engineering, Sejong University, 209 Neungdong-ro, Gwangjin-gu, Seoul 143-747 (Korea, Republic of); Park, Jin Man, E-mail: jinman_park@hotmail.com [Global Technology Center, Samsung Electronics Co., Ltd, 129 Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do 443-742 (Korea, Republic of); Kim, Ki Buem, E-mail: kbkim@sejong.ac.kr [Hybrid Materials Center (HMC), Faculty of Nanotechnology and Advanced Materials Engineering, Sejong University, 209 Neungdong-ro, Gwangjin-gu, Seoul 143-747 (Korea, Republic of)

2015-06-25

Highlights: • Porous metallic glass compact was developed using electro-discharge sintering process. • Uniform PMGC can only be achieved when low electrical input energy was applied. • Functional iron-oxides were formed on the surface of PMGCs by hydrothermal technique. - Abstract: Porous metallic glass compact (PMGC) using electro-discharge sintering (EDS) process of gas atomized Zr{sub 41.2}Ti{sub 13.8}Cu{sub 12.5}Ni{sub 10}Be{sub 22.5} metallic glass powder was developed. The formation of uniform PMGC can only be achieved when low electrical input energy was applied. Functional iron-oxides were formed on the surface of PMGCs by hydrothermal technique. This finding suggests that PMGC can be applied in the new area such as catalyst via hydrothermal technique and offer a promising guideline for using the metallic glasses as a potential functional application.

FTO gene variant modulates the neural correlates of visual food perception.

Science.gov (United States)

Kühn, Anne B; Feis, Delia-Lisa; Schilbach, Leonhard; Kracht, Lutz; Hess, Martin E; Mauer, Jan; Brüning, Jens C; Tittgemeyer, Marc

2016-03-01

Variations in the fat mass and obesity associated (FTO) gene are currently the strongest known genetic factor predisposing humans to non-monogenic obesity. Recent experiments have linked these variants to a broad spectrum of behavioural alterations, including food choice and substance abuse. Yet, the underlying neurobiological mechanisms by which these genetic variations influence body weight remain elusive. Here, we explore the brain structural substrate of the obesity-predisposing rs9939609 T/A variant of the FTO gene in non-obese subjects by means of multivariate classification and use fMRI to investigate genotype-specific differences in neural food-cue reactivity by analysing correlates of a visual food perception task. Our findings demonstrate that MRI-derived measures of morphology along middle and posterior fusiform gyrus (FFG) are highly predictive for FTO at-risk allele carriers, who also show enhanced neural responses elicited by food cues in the same posterior FFG area. In brief, these findings provide first-time evidence for FTO-specific differences in both brain structure and function already in non-obese individuals, thereby contributing to a mechanistic understanding of why FTO is a predisposing factor for obesity. Copyright © 2015 Elsevier Inc. All rights reserved.

Effect of micro-patterned fluorine-doped tin oxide films on electrochromic properties of Prussian blue films

International Nuclear Information System (INIS)

Lee, Kyuha; Kim, A-Young; Park, Ji Hun; Jung, Hun-Gi; Choi, Wonchang; Lee, Hwa Young; Lee, Joong Kee

2014-01-01

Graphical abstract: - Highlights: • PB-based ECD employed micro-patterned FTO electrode was fabricated. • Effect of interface morphology on electrochromic characteristics was examined. • Electrochromic properties were enhanced by employing a patterned interface. - Abstract: The effect of interface morphology on electrochromic characteristics was examined for an electrochromic device (ECD). Micro-patterned fluorine-doped tin oxide (FTO) films were fabricated using a photolithography process. Prussian blue (PB) films were then deposited on the patterned FTO films. The surface areas of both PB films and FTO films were increased by patterning. ECDs were assembled using patterned PB/FTO films as the electrochromic electrode, bare FTO films as the counter electrode, and an electrolyte containing LiClO 4 salt. The increased effective surface area of the patterned PB/FTO electrode boosted the mobility of ions at the interphase between the electrolyte and PB electrode, and the electron transfer between PB films and FTO films. As a result, electrochromic properties such as transmittance and response time were significantly improved by employing the patterned FTO films as the transparent conductive oxide layer of the electrochromic electrode

Interactions between the glass fiber coating and oxidized carbon nanotubes

Energy Technology Data Exchange (ETDEWEB)

Ku-Herrera, J.J., E-mail: jesuskuh@live.com.mx [Centro de Investigación Científica de Yucatán A.C., Unidad de Materiales, Calle 43 No.130, Col. Chuburná de Hidalgo. C.P., 97200 Mérida, Yucatán (Mexico); Avilés, F., E-mail: faviles@cicy.mx [Centro de Investigación Científica de Yucatán A.C., Unidad de Materiales, Calle 43 No.130, Col. Chuburná de Hidalgo. C.P., 97200 Mérida, Yucatán (Mexico); Nistal, A. [Instituto de Cerámica y Vidrio (ICV-CSIC), Kelsen 5, 28049 Madrid (Spain); Cauich-Rodríguez, J.V. [Centro de Investigación Científica de Yucatán A.C., Unidad de Materiales, Calle 43 No.130, Col. Chuburná de Hidalgo. C.P., 97200 Mérida, Yucatán (Mexico); Rubio, F.; Rubio, J. [Instituto de Cerámica y Vidrio (ICV-CSIC), Kelsen 5, 28049 Madrid (Spain); Bartolo-Pérez, P. [Departamento de Física Aplicada, Cinvestav, Unidad Mérida, C.P., 97310 Mérida, Yucatán (Mexico)

2015-03-01

Graphical abstract: - Highlights: • Oxidized multiwall carbon nanotubes (MWCNTs) were deposited onto E-glass fibers. • The role of the fiber coating on the deposition of MWCNTs on the fibers is studied. • A rather homogeneous deposition of MWCNTs is achieved if the coating is maintained. • Multiple oxygen-containing groups were found in the analysis of the fiber coating. • Evidence of chemical interaction between MWCNTs and the fiber coating was found. - Abstract: Chemically oxidized multiwall carbon nanotubes (MWCNTs) were deposited onto commercial E-glass fibers using a dipping procedure assisted by ultrasonic dispersion. In order to investigate the role of the fiber coating (known as “sizing”), MWCNTs were deposited on the surface of as-received E-glass fibers preserving the proprietary coating as well as onto glass fibers which had the coating deliberately removed. Scanning electron microscopy and Raman spectroscopy were used to assess the distribution of MWCNTs onto the fibers. A rather homogeneous coverage with high density of MWCNTs onto the glass fibers is achieved when the fiber coating is maintained. Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and nuclear magnetic resonance (NMR) analyses of the chemical composition of the glass fiber coating suggest that such coating is a complex mixture with multiple oxygen-containing functional groups such as hydroxyl, carbonyl and epoxy. FTIR and XPS of MWCNTs over the glass fibers and of a mixture of MWCNTs and fiber coating provided evidence that the hydroxyl and carboxyl groups of the oxidized MWCNTs react with the oxygen-containing functional groups of the glass fiber coating, forming hydrogen bonding and through epoxy ring opening. Hydrogen bonding and ester formation between the functional groups of the MWCNTs and the silane contained in the coating are also possible.

Interactions between the glass fiber coating and oxidized carbon nanotubes

International Nuclear Information System (INIS)

Ku-Herrera, J.J.; Avilés, F.; Nistal, A.; Cauich-Rodríguez, J.V.; Rubio, F.; Rubio, J.; Bartolo-Pérez, P.

2015-01-01

Graphical abstract: - Highlights: • Oxidized multiwall carbon nanotubes (MWCNTs) were deposited onto E-glass fibers. • The role of the fiber coating on the deposition of MWCNTs on the fibers is studied. • A rather homogeneous deposition of MWCNTs is achieved if the coating is maintained. • Multiple oxygen-containing groups were found in the analysis of the fiber coating. • Evidence of chemical interaction between MWCNTs and the fiber coating was found. - Abstract: Chemically oxidized multiwall carbon nanotubes (MWCNTs) were deposited onto commercial E-glass fibers using a dipping procedure assisted by ultrasonic dispersion. In order to investigate the role of the fiber coating (known as “sizing”), MWCNTs were deposited on the surface of as-received E-glass fibers preserving the proprietary coating as well as onto glass fibers which had the coating deliberately removed. Scanning electron microscopy and Raman spectroscopy were used to assess the distribution of MWCNTs onto the fibers. A rather homogeneous coverage with high density of MWCNTs onto the glass fibers is achieved when the fiber coating is maintained. Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and nuclear magnetic resonance (NMR) analyses of the chemical composition of the glass fiber coating suggest that such coating is a complex mixture with multiple oxygen-containing functional groups such as hydroxyl, carbonyl and epoxy. FTIR and XPS of MWCNTs over the glass fibers and of a mixture of MWCNTs and fiber coating provided evidence that the hydroxyl and carboxyl groups of the oxidized MWCNTs react with the oxygen-containing functional groups of the glass fiber coating, forming hydrogen bonding and through epoxy ring opening. Hydrogen bonding and ester formation between the functional groups of the MWCNTs and the silane contained in the coating are also possible

FTO genotype and weight loss

DEFF Research Database (Denmark)

Livingstone, Katherine M; Celis-Morales, Carlos; Papandonatos, George D

2016-01-01

OBJECTIVE: To assess the effect of the FTO genotype on weight loss after dietary, physical activity, or drug based interventions in randomised controlled trials. DESIGN: Systematic review and random effects meta-analysis of individual participant data from randomised controlled trials. DATA SOURC...

Study of Seal Glass for Solid Oxide Fuel/Electrolyzer Cells

OpenAIRE

Mahapatra, Manoj Kumar

2009-01-01

Seal glass is essential and plays a crucial role in solid oxide fuel/electrolyzer cell performance and durability. A seal glass should have a combination of thermal, chemical, mechanical, and electrical properties in order to seal different cell components and stacks and prevent gas leakage. All the desired properties can simultaneously be obtained in a seal glass by suitable compositional design. In this dissertation, SrO-La₂O₃-A₂O₃-B₂O₃3-SiO₂ based seal glasses have been developed and compo...

Viscoelasticity of metallic, polymeric and oxide glasses

Energy Technology Data Exchange (ETDEWEB)

Pelletier, J.M. [GEMPPM, INSA Lyon, Bat. B. Pascal, 69621 Villeurbanne (France)]. E-mail: Jean-marc.Pelletier@insa-lyon.fr; Gauthier, C. [GEMPPM, INSA Lyon, Bat. B. Pascal, 69621 Villeurbanne (France); Munch, E. [GEMPPM, INSA Lyon, Bat. B. Pascal, 69621 Villeurbanne (France)

2006-12-20

Present work addresses on mechanical spectroscopy experiments performed on bulk metallic glasses (Zr-Ti-Cu-Ni-Be alloys, Mg-Y-Cu alloys), on oxide glasses (SiO{sub 2}-Na{sub 2}O-CaO) and on amorphous polymers (polyethylene terephtalate (PET), nitrile butadiene rubber (NBR), etc.). It appears that whatever the nature of the chemical bonding involved in the material, we observe strong relaxation effects in an intermediate temperature range, near the glass transition temperature. In addition, when crystallization occurs in the initially amorphous material, similar evolution is observed in all the materials. A method is proposed to properly separate elastic, viscoelastic and viscoplastic contributions to the deformation. Finally a physical model is given to describe these viscoelastic phenomena.

Fat mass and obesity associated gene (FTO expression is regulated negatively by the transcription factor Foxa2.

Directory of Open Access Journals (Sweden)

Jianjin Guo

Full Text Available Fat mass and obesity associated gene (FTO is the first gene associated with body mass index (BMI and risk for diabetes. FTO is highly expressed in the brain and pancreas, and is involved in regulating dietary intake and energy expenditure. To investigate the transcriptional regulation of FTO expression, we created 5'-deletion constructs of the FTO promoter to determine which transcription factors are most relevant to FTO expression. The presence of an activation region at -201/+34 was confirmed by luciferase activity analysis. A potential Foxa2 (called HNF-3β binding site and an upstream stimulatory factor (USF-binding site was identified in the -100 bp fragment upstream of the transcription start site (TSS. Furthermore, using mutagenesis, we identified the Foxa2 binding sequence (-26/-14 as a negative regulatory element to the activity of the human FTO promoter. The USF binding site did not affect the FTO promoter activity. Chromatin immunoprecipitation (ChIP assays were performed to confirm Foxa2 binding to the FTO promoter. Overexpression of Foxa2 in HEK 293 cells significantly down-regulated FTO promoter activity and expression. Conversely, knockdown of Foxa2 by siRNA significantly up-regulated FTO expression. These findings suggest that Foxa2 negatively regulates the basal transcription and expression of the human FTO gene.

FTO genotype and weight loss

DEFF Research Database (Denmark)

Livingstone, Katherine M; Celis-Morales, Carlos; Papandonatos, George D

2016-01-01

: Ovid Medline, Scopus, Embase, and Cochrane from inception to November 2015. ELIGIBILITY CRITERIA FOR STUDY SELECTION: Randomised controlled trials in overweight or obese adults reporting reduction in body mass index, body weight, or waist circumference by FTO genotype (rs9939609 or a proxy) after...

Regulation and function of FTO mRNA expression in human skeletal muscle and subcutaneous adipose tissue

DEFF Research Database (Denmark)

Grunnet, Louise G; Nilsson, Emma; Ling, Charlotte

2009-01-01

Objective. Common variants in FTO (the fat-mass and obesity-associated gene) associate with obesity and type 2 diabetes. The regulation and biological function of FTO mRNA expression in target tissue is unknown. We investigated the genetic and non-genetic regulation of FTO mRNA in skeletal muscle...... and adipose tissue, and their influence on in vivo glucose and fat metabolism. Research Design and Methods. The FTO rs9939609 polymorphism was genotyped in two twin cohorts: 1) 298 elderly twins aged 62-83 years with glucose tolerance ranging from normal to type 2 diabetes and 2) 196 young (25-32 years......) and elderly (58-66 years) non-diabetic twins examined by a hyperinsulinemic euglycemic clamp including indirect calorimetry. FTO mRNA expression was determined in subcutaneous adipose tissue (n=226) and skeletal muscle biopsies (n=158). Results. Heritability of FTO expression in both tissues was low, and FTO...

Determination of the specific surface energy of oxides and glasses in the solid-state

International Nuclear Information System (INIS)

Andryushechkin, S.; Karpman, M.

2000-01-01

The production and application of coatings on glasses are used widely in technology. The coatings on glass are used for the regulation of optical, decorative, conducting and other technological and physical properties of glass. In particular, it is important to mention the application of glass fibres for the development of composite materials. However, the specific surface energy of glass and, consequently, its adhesion characteristics are relatively low. The values of these characteristics can be changed by the application of different metallic and nonmetallic coatings is characterised by high surface energy. To produce metallic coatings with the required adhesion strength of glass, it is necessary to have information on the specific surface energy of inorganic glass of different chemical composition. The determination of the relationships between the properties and composition of glass is one of the fundamental problems. At present, a large amount of investigations have been carried out into the investigations of the properties of glass in relation to its composition. However, the problem of establishment of relationships between the properties and composition of glass are especially difficult when examining multicomponent systems (technical glass). It is therefore, in to analyse in each case the properties of not the entire system has a whole but the variation of the properties with temperature of the individual components included in the system, the subsequent application of the additivity principle. The large majority of the glasses represent combinations of oxides of the elements of groups I-III and oxides of the transition metals, forming the mixtures, solid solutions of chemical compounds in the glass production process. Thus, analysis of the characteristics of oxides of the alkali, alkali-earth and transition metals makes it possible to obtain initial data for the evaluation of the surface energy, density, molecular mass of glass containing these oxides

Mesoporous Nickel Oxide (NiO) Nanopetals for Ultrasensitive Glucose Sensing

Science.gov (United States)

Mishra, Suryakant; Yogi, Priyanka; Sagdeo, P. R.; Kumar, Rajesh

2018-01-01

Glucose sensing properties of mesoporous well-aligned, dense nickel oxide (NiO) nanostructures (NSs) in nanopetals (NPs) shape grown hydrothermally on the FTO-coated glass substrate has been demonstrated. The structural study based investigations of NiO-NPs has been carried out by X-ray diffraction (XRD), electron and atomic force microscopies, energy dispersive X-ray (EDX), and X-ray photospectroscopy (XPS). Brunauer-Emmett-Teller (BET) measurements, employed for surface analysis, suggest NiO's suitability for surface activity based glucose sensing applications. The glucose sensor, which immobilized glucose on NiO-NPs@FTO electrode, shows detection of wide range of glucose concentrations with good linearity and high sensitivity of 3.9 μA/μM/cm2 at 0.5 V operating potential. Detection limit of as low as 1 μΜ and a fast response time of less than 1 s was observed. The glucose sensor electrode possesses good anti-interference ability, stability, repeatability & reproducibility and shows inert behavior toward ascorbic acid (AA), uric acid (UA) and dopamine acid (DA) making it a perfect non-enzymatic glucose sensor.

Spray deposited CeO2–TiO2 counter electrode for electrochromic ...

Indian Academy of Sciences (India)

Abstract. Optically passive thin films of CeO2–TiO2 mixed oxides with molar ratio of Ce/Ti of 0.05 were deposited by the spray pyrolysis technique (SPT) on a glass and fluorine-doped tin oxide (FTO)-coated glass substrates. Precur- sor solution containing cerium nitrate hexahydrate (Ce(NO3)2·6H2O) and titanium ...

Fundamental electrochemiluminescence characteristics of fluorine-doped tin oxides synthesized by sol-gel combustion.

Science.gov (United States)

Moon, B H; Chaoumead, A; Sung, Y M

2013-10-01

Fluorine-doped tin oxide (FTO) materials synthesized by sol-gel combustion method were investigated for electrochemical luminescence (ECL) application. Effects of sol-gel combustion conditions on the structures and morphology of the porous FTO (p-FTO) materials were studied. ECL efficiency of p-FTO-based cell was about 251 cd/m2 at 4 V bias, which is higher than the sell using only FTO electrodes (102.8 cd/m2). The highest intensity of the emitting light was obtained at the wavelength of about 610 nm. The porous FTO layer was effective for increasing ECL intensities.

High-temperature oxidation of tungsten covered by layer of glass-enamel melt

International Nuclear Information System (INIS)

Vasnetsova, V.B.; Shardakov, N.T.; Kudyakov, V.Ya.; Deryabin, V.A.

1997-01-01

Corrosion losses of tungsten covered by the layer of glass-enamel melt were determined at 800, 850, 900, 950 deg C. It is shown that the rate of high-temperature oxidation of tungsten decreases after application of glass-enamel melt on its surface. This is probably conditioned by reduction of area of metal interaction with oxidizing atmosphere

Effect of micro-patterned fluorine-doped tin oxide films on electrochromic properties of Prussian blue films

Energy Technology Data Exchange (ETDEWEB)

Lee, Kyuha [Center for Energy Convergence Research, Green City Technology Institute, Korea Institute of Science and Technology, Hwarangno 14-gil 5, Seongbuk-gu, Seoul 136-791 (Korea, Republic of); Kim, A-Young [Center for Energy Convergence Research, Green City Technology Institute, Korea Institute of Science and Technology, Hwarangno 14-gil 5, Seongbuk-gu, Seoul 136-791 (Korea, Republic of); Department of Material Science and Engineering, Korea University, Seoul 136-701 (Korea, Republic of); Park, Ji Hun; Jung, Hun-Gi; Choi, Wonchang; Lee, Hwa Young [Center for Energy Convergence Research, Green City Technology Institute, Korea Institute of Science and Technology, Hwarangno 14-gil 5, Seongbuk-gu, Seoul 136-791 (Korea, Republic of); Lee, Joong Kee, E-mail: leejk@kist.re.kr [Center for Energy Convergence Research, Green City Technology Institute, Korea Institute of Science and Technology, Hwarangno 14-gil 5, Seongbuk-gu, Seoul 136-791 (Korea, Republic of)

2014-09-15

Graphical abstract: - Highlights: • PB-based ECD employed micro-patterned FTO electrode was fabricated. • Effect of interface morphology on electrochromic characteristics was examined. • Electrochromic properties were enhanced by employing a patterned interface. - Abstract: The effect of interface morphology on electrochromic characteristics was examined for an electrochromic device (ECD). Micro-patterned fluorine-doped tin oxide (FTO) films were fabricated using a photolithography process. Prussian blue (PB) films were then deposited on the patterned FTO films. The surface areas of both PB films and FTO films were increased by patterning. ECDs were assembled using patterned PB/FTO films as the electrochromic electrode, bare FTO films as the counter electrode, and an electrolyte containing LiClO{sub 4} salt. The increased effective surface area of the patterned PB/FTO electrode boosted the mobility of ions at the interphase between the electrolyte and PB electrode, and the electron transfer between PB films and FTO films. As a result, electrochromic properties such as transmittance and response time were significantly improved by employing the patterned FTO films as the transparent conductive oxide layer of the electrochromic electrode.

Exogenous Expressions of FTO Wild-Type and R316Q Mutant Proteins Caused an Increase in HNRPK Levels in 3T3-L1 Cells as Demonstrated by DIGE Analysis

Directory of Open Access Journals (Sweden)

Nil Guzel

2017-01-01

Full Text Available Fat mass and obesity-associated protein is an enzyme that oxidatively demethylates DNA. Although there are numerous studies regarding the catalytic function of FTO, the overall existence or absence of FTO on cellular proteome has not been investigated. This study investigated the changes in the soluble proteome of 3T3-L1 cells upon expression of the WT and the mutant (R316Q FTO proteins. Protein extracts prepared from 3T3-L1 cells expressing either the WT or the mutant FTO proteins were used in DIGE experiments. Analysis of the data revealed the number of spots matched to every member and there were 350 ± 20 spots with 30.5% overall mean coefficient of variation. Eleven regulated protein spots were excised from the gels and identified by MALDI-TOF/TOF. One of the identified proteins was heterogeneous nuclear ribonucleoprotein K, which displayed more than 2.6- and 3.7-fold increases in its abundance in the WT and the mutant FTO expressing cells, respectively. Western blot analysis validated these observations. This is the first study revealing the presence of a parallel increase in expressions of FTO and HNRNPK proteins. This increase may codictate the metabolic changes occurring in the cell and may attribute a significance to HNRNPK in FTO-associated transformations.

Chitosan-iron oxide nanocomposite based electrochemical aptasensor for determination of malathion

Energy Technology Data Exchange (ETDEWEB)

Prabhakar, Nirmal, E-mail: nirmalprabhakar@gmail.com; Thakur, Himkusha; Bharti, Anu; Kaur, Navpreet

2016-10-05

An electrochemical aptasensor based on chitosan-iron oxide nanocomposite (CHIT-IO) film deposited on fluorine tin Oxide (FTO) was developed for the detection of malathion. Iron oxide nanoparticles were prepared by co-precipitation method and characterized by Transmission electron microscopy and UV–Visible spectroscopy. The biotinylated DNA aptamer sequence specific to the malathion was immobilized onto the iron oxide doped-chitosan/FTO electrode by using streptavidin as linking molecule. Various characterization studies like Field Emission-Scanning Electron Microscopy (FE-SEM), Fourier Transform Infrared Spectroscopy (FT-IR), and Electrochemical studies were performed to attest the successful fabrication of bioelectrodes. Experimental parameters like aptamer concentration, response time, stability of electrode and reusability studies were optimized. Aptamer immobilized chitosan-iron oxide nanocomposite (APT/SA/CHIT-IO/FTO) bioelectrodes exhibited LOD of about 0.001 ng/mL within 15 min and spike-in studies revealed about 80–92% recovery of malathion from the lettuce leaves and soil sample. - Highlights: • An electrochemical aptasensor for the detection of Malathion has been developed. • Chitosan-iron oxide NP deposited FTO sheets provides platform for aptamer immobilization. • Aptasensor has efficiency to detect malathion upto 0.001 ng/mL within 15 min.

Structural characterization of hog iron oxide content glasses obtained from zinc hydrometallurgy wastes

International Nuclear Information System (INIS)

Romero, M.; Rincon, J.M.; Musik, S.; Kozhujharov, W.

1997-01-01

It has been carried out the structural characterization of high oxide content glasses obtained by melting of a goethite industrial waste from the zinc hydrometallurgy with other raw materials as dolomite and glass cullet. The structural characterization has been carried out by X-ray Diffraction (XRD), X-Ray Diffraction by Amorphous Dispersion (RDF) and Mossbauer spectroscopy. It has been determined the interatomic distance, the oxidation state and the coordination of iron atoms in these glasses. (Author) 16 refs

Effects of Mixed Alkaline Earth Oxides in Potash Silicate Glass ...

African Journals Online (AJOL)

The aim of this work is to investigate the effects of mixed alkaline earth oxide in potash silicate glasses with regards to their physical properties. More recently; there has been an increase in the demand for light weight glasses which retains their physical and chemical properties for both domestic and industrial applications.

FTO Inhibits Insulin Secretion and Promotes NF-κB Activation through Positively Regulating ROS Production in Pancreatic β cells.

Directory of Open Access Journals (Sweden)

Hong-Qi Fan

Full Text Available FTO (Fat mass and obesity-associated is associated with increased risk of obesity and type 2 diabetes incurrence. Pancreas islet β cells dysfunction and insulin resistance are major causes of type 2 diabetes. However, whether FTO plays an important functional role in pancreatic β cells as well as the related molecular mechanism is still unclear. In the present study, the tissue expression profile of FTO was firstly determined using quantitative PCR and western blot. FTO is widely expressed in various tissues and presented with relative high expression in pancreas tissue, especially in endocrine pancreas. FTO overexpression in MIN6 cells achieved by lentivirus delivery significantly inhibits insulin secretion in the presence of glucose stimulus as well as KCl. FTO silence has no effect on insulin secretion of MIN6 cells. However, FTO overexpression doesn't affect the transcription of insulin gene. Furthermore, reactive oxygen species (ROS production and NF-κB activation are significantly promoted by FTO overexpression. Inhibition of intracellular ROS production by N-acetyl-L-cysteine (NAC can alleviate NF-κB activation and restore the insulin secretion mediated by FTO overexpression. A whole transcript-microarray is employed to analyze the differential gene expression mediated by FTO overexpression. The genes which are modulated by FTO are involved in many important biological pathways such as G-protein coupled receptor signaling and NF-κB signaling. Therefore, our study indicates that FTO may contribute to pancreas islet β cells dysfunction and the inhibition of FTO activity is a potential target for the treatment of diabetes.

Oxidation and diffusion process in the ferrous iron-bearing glass fibres near glass temperature

DEFF Research Database (Denmark)

Yue, Yuanzheng; Korsgaard, Martin; Kirkegaard, Lise

2004-01-01

The Fe2+ oxidation and the network modifier diffusion in the Fe2+-bearing glass fibers are studied using differential scanning calorimetry (DSC), thermogravimetry (TG), and secondary neutral mass spectrometry (SNMS). The results show two couplings: 1) between the Fe2+ oxidation and the network...... of the Fe2+-bearing fibers with an average diameter of 3.5 m by knowing the heat-treatment conditions and vice versa....

Impact of variation at the FTO locus on milk fat yield in Holstein dairy cattle.

Science.gov (United States)

Zielke, Lea G; Bortfeldt, Ralf H; Reissmann, Monika; Tetens, Jens; Thaller, Georg; Brockmann, Gudrun A

2013-01-01

This study explores the biological role of the Fat Mass and Obesity associated (FTO) gene locus on milk composition in German Holstein cattle. Since FTO controls energy homeostasis and expenditure and the FTO locus has repeatedly shown association with obesity in human studies, we tested FTO as a candidate gene in particular for milk fat yield, which represents a high amount of energy secreted during lactation. The study was performed on 2,402 bulls and 860 cows where dense milk composition data were available. Genetic information was taken from a 2 Mb region around FTO. Five SNPs and two haplotype blocks in a 725 kb region covering FTO and the neighboring genes RPGRIP1L, U6ATAC, and 5 S rRNA were associated with milk fat yield and also affected protein yield in the same direction. Interestingly, higher frequency SNP alleles and haplotypes within the FTO gene increased milk fat and protein yields by up to 2.8 and 2.2 kg per lactation, respectively, while the most frequent haplotype in the upstream block covering exon 1 of FTO to exon 15 of RPGRIP1L had opposite effects with lower fat and milk yield. Both haplotype blocks were also significant in cows. The loci accounted for about 1% of the corresponding trait variance in the population. The association signals not only provided evidence for at least two causative mutations in the FTO locus with a functional effect on milk but also milk protein yield. The pleiotropic effects suggest a biological function on the usage of energy resources and the control of energy balance rather than directly affecting fat and protein synthesis. The identified effect of the obesity gene locus on milk energy content suggests an impact on infant nutrition by breast feeding in humans.

Impact of variation at the FTO locus on milk fat yield in Holstein dairy cattle.

Directory of Open Access Journals (Sweden)

Lea G Zielke

Full Text Available This study explores the biological role of the Fat Mass and Obesity associated (FTO gene locus on milk composition in German Holstein cattle. Since FTO controls energy homeostasis and expenditure and the FTO locus has repeatedly shown association with obesity in human studies, we tested FTO as a candidate gene in particular for milk fat yield, which represents a high amount of energy secreted during lactation. The study was performed on 2,402 bulls and 860 cows where dense milk composition data were available. Genetic information was taken from a 2 Mb region around FTO. Five SNPs and two haplotype blocks in a 725 kb region covering FTO and the neighboring genes RPGRIP1L, U6ATAC, and 5 S rRNA were associated with milk fat yield and also affected protein yield in the same direction. Interestingly, higher frequency SNP alleles and haplotypes within the FTO gene increased milk fat and protein yields by up to 2.8 and 2.2 kg per lactation, respectively, while the most frequent haplotype in the upstream block covering exon 1 of FTO to exon 15 of RPGRIP1L had opposite effects with lower fat and milk yield. Both haplotype blocks were also significant in cows. The loci accounted for about 1% of the corresponding trait variance in the population. The association signals not only provided evidence for at least two causative mutations in the FTO locus with a functional effect on milk but also milk protein yield. The pleiotropic effects suggest a biological function on the usage of energy resources and the control of energy balance rather than directly affecting fat and protein synthesis. The identified effect of the obesity gene locus on milk energy content suggests an impact on infant nutrition by breast feeding in humans.

Adult onset global loss of the fto gene alters body composition and metabolism in the mouse.

Directory of Open Access Journals (Sweden)

Fiona McMurray

Full Text Available The strongest BMI-associated GWAS locus in humans is the FTO gene. Rodent studies demonstrate a role for FTO in energy homeostasis and body composition. The phenotypes observed in loss of expression studies are complex with perinatal lethality, stunted growth from weaning, and significant alterations in body composition. Thus understanding how and where Fto regulates food intake, energy expenditure, and body composition is a challenge. To address this we generated a series of mice with distinct temporal and spatial loss of Fto expression. Global germline loss of Fto resulted in high perinatal lethality and a reduction in body length, fat mass, and lean mass. When ratio corrected for lean mass, mice had a significant increase in energy expenditure, but more appropriate multiple linear regression normalisation showed no difference in energy expenditure. Global deletion of Fto after the in utero and perinatal period, at 6 weeks of age, removed the high lethality of germline loss. However, there was a reduction in weight by 9 weeks, primarily as loss of lean mass. Over the subsequent 10 weeks, weight converged, driven by an increase in fat mass. There was a switch to a lower RER with no overall change in food intake or energy expenditure. To test if the phenotype can be explained by loss of Fto in the mediobasal hypothalamus, we sterotactically injected adeno-associated viral vectors encoding Cre recombinase to cause regional deletion. We observed a small reduction in food intake and weight gain with no effect on energy expenditure or body composition. Thus, although hypothalamic Fto can impact feeding, the effect of loss of Fto on body composition is brought about by its actions at sites elsewhere. Our data suggest that Fto may have a critical role in the control of lean mass, independent of its effect on food intake.

Genetic association of SNPs in the FTO gene and predisposition to obesity in Malaysian Malays

International Nuclear Information System (INIS)

Apalasamy, Y.D.; Ming, M.F.; Rampal, S.; Bulgiba, A.; Mohamed, Z.

2012-01-01

The common variants in the fat mass- and obesity-associated (FTO) gene have been previously found to be associated with obesity in various adult populations. The objective of the present study was to investigate whether the single nucleotide polymorphisms (SNPs) and linkage disequilibrium (LD) blocks in various regions of the FTO gene are associated with predisposition to obesity in Malaysian Malays. Thirty-one FTO SNPs were genotyped in 587 (158 obese and 429 non-obese) Malaysian Malay subjects. Obesity traits and lipid profiles were measured and single-marker association testing, LD testing, and haplotype association analysis were performed. LD analysis of the FTO SNPs revealed the presence of 57 regions with complete LD (D' = 1.0). In addition, we detected the association of rs17817288 with low-density lipoprotein cholesterol. The FTO gene may therefore be involved in lipid metabolism in Malaysian Malays. Two haplotype blocks were present in this region of the FTO gene, but no particular haplotype was found to be significantly associated with an increased risk of obesity in Malaysian Malays

Genetic association of SNPs in the FTO gene and predisposition to obesity in Malaysian Malays

Energy Technology Data Exchange (ETDEWEB)

Apalasamy, Y.D. [Pharmacogenomics Laboratory, Department of Pharmacology, Faculty of Medicine, University of Malaya, Kuala Lumpur (Malaysia); Ming, M.F.; Rampal, S.; Bulgiba, A. [Julius Centre University of Malaya, Department of Social and Preventive Medicine, Faculty of Medicine, University of Malaya, Kuala Lumpur (Malaysia); Mohamed, Z. [Pharmacogenomics Laboratory, Department of Pharmacology, Faculty of Medicine, University of Malaya, Kuala Lumpur (Malaysia)

2012-08-24

The common variants in the fat mass- and obesity-associated (FTO) gene have been previously found to be associated with obesity in various adult populations. The objective of the present study was to investigate whether the single nucleotide polymorphisms (SNPs) and linkage disequilibrium (LD) blocks in various regions of the FTO gene are associated with predisposition to obesity in Malaysian Malays. Thirty-one FTO SNPs were genotyped in 587 (158 obese and 429 non-obese) Malaysian Malay subjects. Obesity traits and lipid profiles were measured and single-marker association testing, LD testing, and haplotype association analysis were performed. LD analysis of the FTO SNPs revealed the presence of 57 regions with complete LD (D' = 1.0). In addition, we detected the association of rs17817288 with low-density lipoprotein cholesterol. The FTO gene may therefore be involved in lipid metabolism in Malaysian Malays. Two haplotype blocks were present in this region of the FTO gene, but no particular haplotype was found to be significantly associated with an increased risk of obesity in Malaysian Malays.

Association between FTO variant and change in body weight and its interaction with dietary factors

DEFF Research Database (Denmark)

Vimaleswaran, Karani S; Ängquist, Lars; Hansen, Rikke D

2012-01-01

Although FTO is an established obesity-susceptibility locus, it remains unknown whether it influences weight change in adult life and whether diet attenuates this association. Therefore, we investigated the association of FTO-rs9939609 with changes in weight and waist circumference (WC) during 6......-analyses, FTO-rs9939609 was associated with BMI (β (SE), 0.17 (0.08) kg·m(-2)/allele; P = 0.034) and WC (0.47 (0.21) cm/allele; P = 0.026) at baseline, but not with weight change (5.55 (12.5) g·year(-1)/allele; P = 0.66) during follow up. In the CNC-analysis, FTO-rs9939609 was associated with increased risk...... of being a weight-gainer (OR: 1.1; P = 0.045). We observed no interaction between FTO-rs9939609 and dietary fat, protein and carbohydrate, and GI on BMI and WC at baseline or on change in weight and WC. FTO-rs9939609 is associated with BMI and WC at baseline, but association with weight gain is weak...

Genetic association of SNPs in the FTO gene and predisposition to obesity in Malaysian Malays

Directory of Open Access Journals (Sweden)

Y.D. Apalasamy

2012-12-01

Full Text Available The common variants in the fat mass- and obesity-associated (FTO gene have been previously found to be associated with obesity in various adult populations. The objective of the present study was to investigate whether the single nucleotide polymorphisms (SNPs and linkage disequilibrium (LD blocks in various regions of the FTO gene are associated with predisposition to obesity in Malaysian Malays. Thirty-one FTO SNPs were genotyped in 587 (158 obese and 429 non-obese Malaysian Malay subjects. Obesity traits and lipid profiles were measured and single-marker association testing, LD testing, and haplotype association analysis were performed. LD analysis of the FTO SNPs revealed the presence of 57 regions with complete LD (D’ = 1.0. In addition, we detected the association of rs17817288 with low-density lipoprotein cholesterol. The FTO gene may therefore be involved in lipid metabolism in Malaysian Malays. Two haplotype blocks were present in this region of the FTO gene, but no particular haplotype was found to be significantly associated with an increased risk of obesity in Malaysian Malays.

Macronutrients and the FTO gene expression in hypothalamus; a systematic review of experimental studies.

Science.gov (United States)

Doaei, Saeid; Kalantari, Naser; Mohammadi, Nastaran Keshavarz; Tabesh, Ghasem Azizi; Gholamalizadeh, Maryam

The various studies have examined the relationship between FTO gene expression and macronutrients levels. In order to obtain better viewpoint from this interactions, all of existing studies were reviewed systematically. All published papers have been obtained and reviewed using standard and sensitive keywords from databases such as CINAHL, Embase, PubMed, PsycInfo, and the Cochrane, from 1990 to 2016. The results indicated that all of 6 studies that met the inclusion criteria (from a total of 428 published article) found FTO gene expression changes at short-term follow-ups. Four of six studies found an increased FTO gene expression after calorie restriction, while two of them indicated decreased FTO gene expression. The effect of protein, carbohydrate and fat were separately assessed and suggested by all of six studies. In Conclusion, The level of FTO gene expression in hypothalamus is related to macronutrients levels. Future research should evaluate the long-term impact of dietary interventions. Copyright © 2017. Published by Elsevier B.V.

Macronutrients and the FTO gene expression in hypothalamus; a systematic review of experimental studies

Directory of Open Access Journals (Sweden)

Saeid Doaei

2017-03-01

Full Text Available The various studies have examined the relationship between FTO gene expression and macronutrients levels. In order to obtain better viewpoint from this interactions, all of existing studies were reviewed systematically. All published papers have been obtained and reviewed using standard and sensitive keywords from databases such as CINAHL, Embase, PubMed, PsycInfo, and the Cochrane, from 1990 to 2016. The results indicated that all of 6 studies that met the inclusion criteria (from a total of 428 published article found FTO gene expression changes at short-term follow-ups. Four of six studies found an increased FTO gene expression after calorie restriction, while two of them indicated decreased FTO gene expression. The effect of protein, carbohydrate and fat were separately assessed and suggested by all of six studies. In Conclusion, The level of FTO gene expression in hypothalamus is related to macronutrients levels. Future research should evaluate the long-term impact of dietary interventions.

Fiber Fabrication Facility for Non-Oxide and Specialty Glasses

Data.gov (United States)

Federal Laboratory Consortium — FUNCTION: Unique facility for the research, development, and fabrication of non-oxide and specialty glasses and fibers in support of Navy/DoD programs.DESCRIPTION:...

Expression studies of the obesity candidate gene FTO in pig

DEFF Research Database (Denmark)

Madsen, Majbritt Busk; Birck, Malene Muusfeldt; Fredholm, Merete

2010-01-01

Obesity is an increasing problem worldwide and research on candidate genes in good animal models is highly needed. The pig is an excellent model as its metabolism, organ size, and eating habits resemble that of humans. The present study is focused on the characterization of the fat mass and obesity...... associated gene (FTO) in pig. This gene has recently been associated with increased body mass index in several human populations. To establish information on the expression profile of FTO in the pig we performed quantitative PCR in a panel of adult pig tissues and in tissues sampled at different...... and cerebellum). Additionally, in order to see the involvement of the FTO gene in obesity, the changes in expression level were investigated in a nutritional study in brain of Gottingen minipigs under a high cholesterol diet. Significantly higher (P

Fabrication and characterization of vacuum deposited fluorescein thin films

Energy Technology Data Exchange (ETDEWEB)

Jalkanen, Pasi, E-mail: pasi.jalkanen@gmail.co [University of Jyvaeskylae, Department of Physics, Nanoscience center (NSC), P.O. Box 35, FI-40014 Jyvaeskylae (Finland); Kulju, Sampo, E-mail: sampo.j.kulju@jyu.f [University of Jyvaeskylae, Department of Physics, Nanoscience center (NSC), P.O. Box 35, FI-40014 Jyvaeskylae (Finland); Arutyunov, Konstantin, E-mail: konstantin.arutyunov@jyu.f [University of Jyvaeskylae, Department of Physics, Nanoscience center (NSC), P.O. Box 35, FI-40014 Jyvaeskylae (Finland); Antila, Liisa, E-mail: liisa.j.antila@jyu.f [University of Jyvaeskylae, Department of Chemistry, Nanoscience center (NSC) P.O. Box 35, FI-40014 Jyvaeskylae (Finland); Myllyperkioe, Pasi, E-mail: pasi.myllyperkio@jyu.f [University of Jyvaeskylae, Department of Chemistry, Nanoscience center (NSC) P.O. Box 35, FI-40014 Jyvaeskylae (Finland); Ihalainen, Teemu, E-mail: teemu.o.ihalainen@jyu.f [University of Jyvaeskylae, Department of Biology, Nanoscience center (NSC), P.O. Box 35, FI-40014 Jyvaeskylae (Finland); Kaeaeriaeinen, Tommi, E-mail: tommi.kaariainen@lut.f [Lappeenranta University of Technology, ASTRal, P.O. Box 181, FI-50101 Mikkeli (Finland); Kaeaeriaeinen, Marja-Leena, E-mail: marja-leena.kaariainen@lut.f [Lappeenranta University of Technology, ASTRal, P.O. Box 181, FI-50101 Mikkeli (Finland); Korppi-Tommola, Jouko, E-mail: jouko.korppi-tommola@jyu.f [University of Jyvaeskylae, Department of Biology, Nanoscience center (NSC), P.O. Box 35, FI-40014 Jyvaeskylae (Finland)

2011-03-31

Simple vacuum evaporation technique for deposition of dyes on various solid surfaces has been developed. The method is compatible with conventional solvent-free nanofabrication processing enabling fabrication of nanoscale optoelectronic devices. Thin films of fluorescein were deposited on glass, fluorine-tin-oxide (FTO) coated glass with and without atomically layer deposited (ALD) nanocrystalline 20 nm thick anatase TiO{sub 2} coating. Surface topology, absorption and emission spectra of the films depend on their thickness and the material of supporting substrate. On a smooth glass surface the dye initially forms islands before merging into a uniform layer after 5 to 10 monolayers. On FTO covered glass the absorption spectra are similar to fluorescein solution in ethanol. Absorption spectra on ALD-TiO{sub 2} is red shifted compared to the film deposited on bare FTO. The corresponding emission spectra at {lambda} = 458 nm excitation show various thickness and substrate dependent features, while the emission of films deposited on TiO{sub 2} is quenched due to the effective electron transfer to the semiconductor conduction band.

The electronic and optical properties of germanium tellurite glasses containing various transition metal oxides

International Nuclear Information System (INIS)

Khan, M.N.

1988-01-01

Various transition metal oxides, such as TiO 2 , V 2 O 5 , NiO, CuO, and ZnO are added to germanium-tellurite glass and measurements are reported of the electrical conductivity, density, optical absorption, infra-red absorption spectra, and electron spin resonance. It is found that the d.c. conductivity of glasses containing the same amount of V 2 O 5 is higher than that of germanium tellurite glasses containing a similar amount of other transition metal oxides, and is due to hopping between localized states. The optical absorption measurements show that the fundamental absorption edge is a function of glass composition and the optical absorption is due to forbidden indirect transitions. From the infra-red absorption spectra, it is found that the addition of transition metal oxides does not introduce any new absorption band in the infra-red spectrum of germanium tellurite glasses. A small shift of existing absorptions toward higher wave number is observed. The ESR measurements revealed that some transition metal ions are diamagnetic while others are paramagnetic in the glass network. (author)

Structure and nano-mechanical characteristics of surface oxide layers on a metallic glass.

Science.gov (United States)

Caron, A; Qin, C L; Gu, L; González, S; Shluger, A; Fecht, H-J; Louzguine-Luzgin, D V; Inoue, A

2011-03-04

Owing to their low elastic moduli, high specific strength and excellent processing characteristics in the undercooled liquid state, metallic glasses are promising materials for applications in micromechanical systems. With miniaturization of metallic mechanical components down to the micrometer scale, the importance of a native oxide layer on a glass surface is increasing. In this work we use TEM and XPS to characterize the structure and properties of the native oxide layer grown on Ni(62)Nb(38) metallic glass and their evolution after annealing in air. The thickness of the oxide layer almost doubled after annealing. In both cases the oxide layer is amorphous and consists predominantly of Nb oxide. We investigate the friction behavior at low loads and in ambient conditions (i.e. at T = 295 K and 60% air humidity) of both as-cast and annealed samples by friction force microscopy. After annealing the friction coefficient is found to have significantly increased. We attribute this effect to the increase of the mechanical stability of the oxide layer upon annealing.

Reduction-oxidation Enabled Glass-ceramics to Stainless Steel Bonding Part II interfacial bonding analysis

Energy Technology Data Exchange (ETDEWEB)

Dai, Steve Xunhu [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-09-01

Among glass-ceramic compositions modified with a variety of oxidants (AgO, FeO, NiO, PbO, SnO, CuO, CoO, MoO₃ and WO₃) only CuO and CoO doped glass-ceramics showed existence of bonding oxides through reduction-oxidation (redox) at the GC-SS interface. The CuO-modified glass-ceramics demonstrate the formation of a continuous layer of strong bonding Cr₂O₃ at the interface in low partial oxygen (PO₂) atmosphere. However, in a local reducing atmosphere, the CuO is preferentially reduced at the surface of glass-ceramic rather than the GC-SS interface for redox. The CoO-modified glass-ceramics demonstrate improved GC-SS bonding. But the low mobility of Co⁺⁺ ions in the GC limited the amount of CoO that can diffuse to and participate in redox at the interface.

The fat mass and obesity associated gene FTO functions in the brain to regulate postnatal growth in mice.

Directory of Open Access Journals (Sweden)

Xue Gao

2010-11-01

Full Text Available FTO (fat mass and obesity associated was identified as an obesity-susceptibility gene by several independent large-scale genome association studies. A cluster of SNPs (single nucleotide polymorphism located in the first intron of FTO was found to be significantly associated with obesity-related traits, such as body mass index, hip circumference, and body weight. FTO encodes a protein with a novel C-terminal α-helical domain and an N-terminal double-strand β-helix domain which is conserved in Fe(II and 2-oxoglutarate-dependent oxygenase family. In vitro, FTO protein can demethylate single-stranded DNA or RNA with a preference for 3-methylthymine or 3-methyluracil. Its physiological substrates and function, however, remain to be defined. Here we report the generation and analysis of mice carrying a conditional deletion allele of Fto. Our results demonstrate that Fto plays an essential role in postnatal growth. The mice lacking Fto completely display immediate postnatal growth retardation with shorter body length, lower body weight, and lower bone mineral density than control mice, but their body compositions are relatively normal. Consistent with the growth retardation, the Fto mutant mice have reduced serum levels of IGF-1. Moreover, despite the ubiquitous expression of Fto, its specific deletion in the nervous system results in similar phenotypes as the whole body deletion, indicating that Fto functions in the central nerve system to regulate postnatal growth.

Copper oxide content dependence of crystallization behavior, glass forming ability, glass stability and fragility of lithium borate glasses

International Nuclear Information System (INIS)

Soliman, A.A.; Kashif, I.

2010-01-01

Differential thermal analysis (DTA) and X-ray diffraction (XRD) have been employed to investigate the copper oxide content dependence of the glass transition temperatures data, activation energy for the glass transition E t , glass stability GS, fragility index Fi, the glass-forming ability (GFA) and crystallization behavior of {(100-x) mol% Li 2 B 4 O 7 -x mol% CuO} glass samples, where x=0-40 mol% CuO. From the dependence of the glass transition temperature T g on the heating rate β, the fragility, F i , and the activation energy, E t , have been calculated. It is seen that F i and E t are attained their minimum values at 0 x -T g , SCL region and the GS. The GFA has been investigated on the basis of Hruby parameter K H , which is a strong indicator of GFA, and the relaxation time. Results of GFA are in good agreement with the fragility index, F i , calculations indicating that {90Li 2 B 4 O 7 .10CuO} is the best glass former. The stronger glass forming ability has decreasing the fragility index. XRD result indicates that no fully amorphous samples but a mixture of crystalline and amorphous phases are formed in the samples containing x>25 mol% CuO and below it composed of glassy phase. Increasing the CuO content above 25 mol% helps the crystallization process, and thus promotes a distinct SCL region. XRD suggests the presence of micro-crystallites of remaining residual amorphous matrix by increasing the CuO content.

Laser-excited fluorescence spectroscopy of oxide glasses

International Nuclear Information System (INIS)

Weber, M.J.

1977-01-01

Laser-induced fluorescence line narrowing was applied to investigate the local fields and interactions of paramagnetic ions in oxide glasses. Studies included the site dependence of energy levels, radiative and nonradiative transition probabilities, homogeneous line broadening, and ion--ion energy transfer of rare earth ions. These results and the experimental techniques are reviewed briefly; the use of paramagnetic ions other than the rare earths is also considered. Recently, laser-excited fluorescence spectroscopy was used to investigate modifications in the local structure of lithium borate glass caused by compositional changes and phase separation and the site dependence of nonradiative relaxation of paramagnetic ions by multiphonon processes. These results and their implications are discussed. 6 figures

Glass/Ceramic Composites for Sealing Solid Oxide Fuel Cells

Science.gov (United States)

Bansal, Narottam P.; Choi, Sung R.

2007-01-01

A family of glass/ceramic composite materials has been investigated for use as sealants in planar solid oxide fuel cells. These materials are modified versions of a barium calcium aluminosilicate glass developed previously for the same purpose. The composition of the glass in mole percentages is 35BaO + 15CaO + 5Al2O3 + 10B2O3 + 35SiO2. The glass seal was found to be susceptible to cracking during thermal cycling of the fuel cells. The goal in formulating the glass/ ceramic composite materials was to (1) retain the physical and chemical advantages that led to the prior selection of the barium calcium aluminosilicate glass as the sealant while (2) increasing strength and fracture toughness so as to reduce the tendency toward cracking. Each of the composite formulations consists of the glass plus either of two ceramic reinforcements in a proportion between 0 and 30 mole percent. One of the ceramic reinforcements consists of alumina platelets; the other one consists of particles of yttria-stabilized zirconia wherein the yttria content is 3 mole percent (3YSZ). In preparation for experiments, panels of the glass/ceramic composites were hot-pressed and machined into test bars.

Oxide glass to high temperature ceramic superconductors - a novel route

International Nuclear Information System (INIS)

Chaudhuri, B.K.; Som, K.K.

1992-01-01

Recently it has been discovered that many of transition metal oxide (TMO) glasses like Bi-Sr-Ca-Cu-O, Y-Ba-Cu-O, Bi-Pb-Sr-Ca-Cu-O etc. can be directly converted to the corresponding high temperature superconducting phases by properly annealing the respective glasses. In this review recent developements in this field are summarised. The structural, electrical, dielectrical, magnetic, optical, and other properties of these new type of (TMO) glass systems have been elucidated comparing them with the corresponding results of already known (TMO) glasses which do not become superconductors on annealing above their glass transition temperatures (T g ). The electrical properties of this novel glass system have been analysed with reference to the various existing theoretical models based on polaron hopping conduction mechanism. The electrical, magnetic, and other properties of the respective superconductors obtained from their corresponding glass phases by annealing above (T g ) and the possibility of drawing wires, ribbons etc. from these glass matrices and then converting them to their high T c superconducting phases have also been discussed. (author). 107 refs., 32 figs., 5 tabs

FTO genotype, physical activity, and coronary heart disease risk in Swedish men and women.

Science.gov (United States)

Gustavsson, Jaana; Mehlig, Kirsten; Leander, Karin; Lissner, Lauren; Björck, Lena; Rosengren, Annika; Nyberg, Fredrik

2014-04-01

Variants in the fat mass- and obesity-associated gene (FTO) predisposing to obesity and diabetes mellitus have also been associated with cardiovascular disease. Physical activity has been suggested to attenuate the FTO effect on obesity, but it is unknown whether this is also true for cardiovascular disease. Therefore, we explored whether physical activity modifies the FTO association with coronary heart disease (CHD). FTO rs9939609 (T>A) polymorphism was genotyped in 2 Swedish population-based case-control studies with 1743 CHD cases and 4402 population controls (25-74 years of age; 41% women). Leisure time physical activity was assessed by questionnaires, and 3 levels were defined: low, medium, and high. Overall, carriers of the FTO A allele had an increased risk of CHD (odds ratio, 1.20; 95% confidence interval, 1.06-1.37) adjusted for age, sex, study, and body mass index. Although A-allele carriers with low physical activity had the highest CHD risk (odds ratio, 3.30; 95% confidence interval, 2.44-4.46) compared with those with TT genotype and high activity, the effects of FTO genotype and physical activity on CHD risk were approximately additive, indicating the absence of additive interaction. The stratum-specific relative risks of CHD from the A allele in subjects with low, medium, and high physical activity were odds ratio 1.11 (95% confidence interval, 0.77-1.60), 1.22 (1.04-1.44), and 1.38 (1.06-1.80), respectively, but the suggested multiplicative interaction was not significant. FTO rs9939609 A-allele carriers have an increased CHD risk, and the association is not counteracted by increased physical activity.

Loss-of-Function Mutation in the Dioxygenase-Encoding FTO Gene Causes Severe Growth Retardation and Multiple Malformations

Science.gov (United States)

Boissel, Sarah; Reish, Orit; Proulx, Karine; Kawagoe-Takaki, Hiroko; Sedgwick, Barbara; Yeo, Giles S.H.; Meyre, David; Golzio, Christelle; Molinari, Florence; Kadhom, Noman; Etchevers, Heather C.; Saudek, Vladimir; Farooqi, I. Sadaf; Froguel, Philippe; Lindahl, Tomas; O'Rahilly, Stephen; Munnich, Arnold; Colleaux, Laurence

2009-01-01

FTO is a nuclear protein belonging to the AlkB-related non-haem iron- and 2-oxoglutarate-dependent dioxygenase family. Although polymorphisms within the first intron of the FTO gene have been associated with obesity, the physiological role of FTO remains unknown. Here we show that a R316Q mutation, inactivating FTO enzymatic activity, is responsible for an autosomal-recessive lethal syndrome. Cultured skin fibroblasts from affected subjects showed impaired proliferation and accelerated senescence. These findings indicate that FTO is essential for normal development of the central nervous and cardiovascular systems in human and establish that a mutation in a human member of the AlkB-related dioxygenase family results in a severe polymalformation syndrome. PMID:19559399

The Association Between the FTO rs9939609 Variant and Malignant Pleural Mesothelioma Risk: A Case-Control Study.

Science.gov (United States)

Khella, Mina S; Salem, Ahmed M; Abdel-Rahman, Omar; Saad, Amr S

2018-02-01

Despite the established link between malignant pleural mesothelioma (MPM) and asbestos exposure, genetic risk factors may play a key role in MPM pathogenesis. The rs9939609 polymorphism in the FTO gene has recently been implicated as a risk factor for some types of cancer, such as breast, pancreatic, and prostate cancers. FTO variation is associated with altered adipocytokine expression and oxidative stress inflammation, which may influence asbestos mediated-carcinogenesis. This is the first study to investigate a possible association between this polymorphism and MPM risk. FTO rs9939609 (T >A) genotypes were screened using a TaqMan ® Genotyping Assay in a total of 235 Egyptian subjects (86 MPM patients versus 149 controls). The chi-square test and logistic regression were used to evaluate the association between the candidate variant and MPM risk using a case-control design. In the additive genetic model, the AT and AA genotypes were associated with a 2.48-fold (95% confidence intervals [CI] = 1.04-5.92, p = 0.04) and a 3.46-fold (95% CI = 0.99-12.01, p = 0.051) increase in the odds of developing MPM, respectively, when compared to the TT genotype after adjustment for body mass index, age, and gender. Additionally, in the dominant genetic model AT/AA genotypes were associated with a 2.63-fold increase in the odds of developing MPM (95% CI = 1.13-6.12, p = 0.025). The present study shows for the first time that rs9939609 polymorphism in the FTO gene may be a genetic risk factor for MPM. This study highlights the association of this genetic polymorphism with cancer susceptibility, and therefore, it should be investigated in various other populations, in relation to different types of cancer, and with larger sample sizes.

Development of tellurium oxide and lead-bismuth oxide glasses for mid-wave infra-red transmission optics

Science.gov (United States)

Zhou, Beiming; Rapp, Charles F.; Driver, John K.; Myers, Michael J.; Myers, John D.; Goldstein, Jonathan; Utano, Rich; Gupta, Shantanu

2013-03-01

Heavy metal oxide glasses exhibiting high transmission in the Mid-Wave Infra-Red (MWIR) spectrum are often difficult to manufacture in large sizes with optimized physical and optical properties. In this work, we researched and developed improved tellurium-zinc-barium and lead-bismuth-gallium heavy metal oxide glasses for use in the manufacture of fiber optics, optical components and laser gain materials. Two glass families were investigated, one based upon tellurium and another based on lead-bismuth. Glass compositions were optimized for stability and high transmission in the MWIR. Targeted glass specifications included low hydroxyl concentration, extended MWIR transmission window, and high resistance against devitrification upon heating. Work included the processing of high purity raw materials, melting under controlled dry Redox balanced atmosphere, finning, casting and annealing. Batch melts as large as 4 kilograms were sprue cast into aluminum and stainless steel molds or temperature controlled bronze tube with mechanical bait. Small (100g) test melts were typically processed in-situ in a 5%Au°/95%Pt° crucible. Our group manufactured and evaluated over 100 different experimental heavy metal glass compositions during a two year period. A wide range of glass melting, fining, casting techniques and experimental protocols were employed. MWIR glass applications include remote sensing, directional infrared counter measures, detection of explosives and chemical warfare agents, laser detection tracking and ranging, range gated imaging and spectroscopy. Enhanced long range mid-infrared sensor performance is optimized when operating in the atmospheric windows from ~ 2.0 to 2.4μm, ~ 3.5 to 4.3μm and ~ 4.5 to 5.0μm.

Raman and DSC studies of fragility in tellurium-zinc oxide glass formers

International Nuclear Information System (INIS)

Stavrou, Elissaios; Kripotou, Sotiria; Raptis, Constantine; Turrell, Sylvia; Syassen, Karl

2011-01-01

Raman scattering and differential scanning calorimetry (DSC) measurements have been carried out in four mixed (TeO 2 ) 1-x (ZnO) x (x = 0.1, 0.2, 0.3, 0.4) glasses at high temperatures (Raman and DSC through the glass transition) and high pressures (Raman) with the aim of determining the fragility of these glass forming oxides. Four different criteria, corresponding to four parameters, were applied to assess the fragility of the glasses. From the DSC studies, we have obtained the fragility parameter m which corresponds to the slopes of Arrhenius (lnQ vs. 1/T g , were Q is the heating rate) plots, and the glass transition width ΔT g . Also, from the low-frequency Raman scattering, and in particular the boson peak intensity of the glasses at T g , we have estimated the fragility ratio r R (T g ) = I min /I max whose value serves as another (empirical) fragility criterion. Finally, from high pressure Raman measurements on the glasses, we have estimated the Grueneisen parameter γ T for each glass, which constitutes the fourth fragility parameter adopted in this work. Considering the four parameters ΔT g , m, r (T g ) and γ T and the generally accepted (empirical) fragility criteria, we conclude that the mixed tellurium-zinc oxides constitute strong-to-intermediate glass formers (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Effect of swift heavy ion (SHI) irradiation on transparent conducting oxide electrodes for dye-sensitized solar cell applications

Science.gov (United States)

Singh, Hemant Kr.; Avasthi, D. K.; Aggarwal, Shruti

2015-06-01

Transparent conducting oxides (TCOs) are used as electrodes in dye-sensitized solar cells (DSSCs) because of their properties such as high transmittance and low resistivity. In the present work, the effects of swift heavy ion (SHI) irradiation on various types of TCOs are presented. The objective of this study is to investigate the effect of SHI on TCOs. For the present study, three different types of TCOs are considered, namely, (a) FTO (fluorine-doped tin oxide, SnO2:F) on a Nippon glass substrate, (b) ITO (indium tin oxide, In2O3:Sn) coated on polyethylene terephthalate (PET) on a Corning glass substrate, and (c) ITO on a Corning glass substrate. These films are irradiated with 120 MeV Ag+9 ions at fluences ranging from 3.0 × 1011 ions/cm2 to 3.0 × 1013 ions/cm2. The structural, morphological, optical and electrical properties are studied via X-ray diffraction (XRD), atomic force microscopy (AFM), UV-Vis absorption spectroscopy and four-probe resistivity measurements, respectively. The ITO-PET electrode is found to exhibit superior conductivity and transmittance properties in comparison with the others after irradiation and, therefore, to be the most suitable for solar cell applications.

Leidt een goed FTO tot beter voorschrijven?

NARCIS (Netherlands)

Eimers, M.; Aalst, A. van der; Pelzer, B.J.; Teichert, M.; Wit, H. de

2008-01-01

Inleiding - We onderzochten of de kwaliteit van voorschrijven van huisartsen samenhangt met de kwaliteit van het farmacotherapieoverleg (FTO) waaraan deze huisartsen deelnemen. Methode - Als maat voor de kwaliteit van voorschrijven gebruiken we negen voorschrijfindicatoren die ontwikkeld zijn door

Synthesis of ZnO nanowire arrays on ZnO−TiO{sub 2} mixed oxide seed layer for dye sensitized solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Marimuthu, T. [Advanced Materials and Thin Film Physics Lab, Department of Physics, Alagappa University, Karaikudi (India); Anandhan, N., E-mail: anandhan_kn@rediffmail.com [Advanced Materials and Thin Film Physics Lab, Department of Physics, Alagappa University, Karaikudi (India); Thangamuthu, R. [Electrochemical Materials Science Division, CSIR-Central Electrochemical Research Institute, Karaikudi (India); Mummoorthi, M. [Advanced Materials and Thin Film Physics Lab, Department of Physics, Alagappa University, Karaikudi (India); Ravi, G. [Photonic Crystal Lab, Department of Physics, Alagappa University, Karaikudi (India)

2016-08-25

ZnO nanowire arrays (NWAs) were synthesized on ZnO−TiO{sub 2} mixed oxide seeded FTO conducting glass plate by two-step sol-gel and hydrothermal method, respectively. X-ray diffraction patterns reveal the presence of mixed and hexagonal phases in seed layer and NWAs, respectively. Scanning electron microscope images showed that the FTO glass plate is uniformly covered with grains and a few nanorods in seed layer and dense NWAs are vertically grown on the seed layer. The hexagonal structure and high crystal quality have been confirmed by micro Raman spectra. Photoluminescence spectra also present that NWAs have high crystal quality and less atomic defects. UV spectra indicate that NWAs are absorbed more dye molecules and it has the band gap equal to bulk material. The efficiency of ZnO−TiO{sub 2} mixed oxide seed layer and ZnO NWAs is found to be 0.56 and 0.84% respectively. Electrochemical impedance spectra reveal that NWAs DSSC has high charge transfer recombination resistance than the seed layer DSSC. - Highlights: • ZnO nanowire arrays were synthesized by two-step sol-gel and hydrothermal method. • The crystal structure and crystalline quality of films are confirmed by Raman spectra. • The emission properties of films are investigated by photoluminescence spectra. • ZnO nanowire arrays (NWAs) have higher charge transfer recombination resistance. • The conversion efficiency of the seed layer and NWAs is to be 0.56 and 0.84%.

Electrochemical grafting of TiO2-based photo-anodes and its effect in dye-sensitized solar cells

DEFF Research Database (Denmark)

Lund, Torben; Phuong, Nguyen Tuyet; Ruhland, Thomas Gerhard Aloysius

2015-01-01

We demonstrate that hydroxyl-groups which are located on the surfaces of mesoporous metal oxides (in particular sintered layers of F-doped tin oxide (FTO) and TiO2 on glass plates) are capable of undergoing reactions with 4-nitrobenzene radicals. The highly reactive benzene radicals are generated...

Exposure Buildup Factors for Heavy Metal Oxide Glass: A Radiation Shield

DEFF Research Database (Denmark)

Manonara, S. R.; Hanagodimath, S. M.; Gerward, Leif

2011-01-01

Gamma ray exposure buildup factors for three Heavy Metal Oxide (HMO) glass systems, viz. PbO-Bi2O3-B2O3, PbO-B2O3, and Bi2O3-B2O3 glasses are presented. The computations were done by interpolation method using the Geometric Progression fitting formula and ANSI/ANS-6.4.3 library for the energy ran...... of graphs. Buildup factors of these HMO glasses cannot be found in any standard database, but they are useful for practical calculations in gamma ray shield designs, and they also, help to determine and control the thickness of the shielding material used.......Gamma ray exposure buildup factors for three Heavy Metal Oxide (HMO) glass systems, viz. PbO-Bi2O3-B2O3, PbO-B2O3, and Bi2O3-B2O3 glasses are presented. The computations were done by interpolation method using the Geometric Progression fitting formula and ANSI/ANS-6.4.3 library for the energy range...... from 0.015 to 15 MeV, up to penetration depths of 40 mfp (mean free path). The buildup factors have been studied as functions of incident photon energy and penetration depth. The variations in the buildup factor, for all the glass systems, in different energy regions; have been presented in the form...

Fat phenotype, associated factors and rs9939609 polymorphism of the FTO gene

Directory of Open Access Journals (Sweden)

William Alves Lima

2010-02-01

Full Text Available The purpose of this work was to review the main results of studies that have analysed the relationship between the rs9939609 single nucleotide polymorphism (SNP of the FTO gene and the manifestation of overweight/obesity with its associated co-morbidity, and to discuss the interaction of this polymorphism with the other factors which cause obesity. The search was performed using the MEDLINE, Highwire, Science Direct and SciELO databases, applying the following key words: FTO rs9939609, obesity genetic, gene associated obesity, FTO contributes obesity. Inclusion criteria were: original articles where the search was performed in humans and including the rs9939609. Articles that analysed the FTO gene associated with preinstalled hormonal diseases were excluded. Of the several SNP associated with the FTO gene, rs9939609 has been the most researched (studied. This SNP comprises the A and T alleles, with the A homozygote being most susceptible to the development of overweight/obesity in all age ranges, especially in the caucasian population. In this situation, the control of environmental factors (alimentation and physical activity can prevent the excessive build up of fats. Obesity is related to the development of non-transmissible chronic illnesses. Association of rs9939609 polymorphism with the lipidic profile and glycemia were observed. The practicing of physical exercise and feeding habits seem to be the main contributors in the development of overweight/obesity and its resulting co-morbidity.

Evidence of an Intermediate Phase in bulk alloy oxide glass sysem

Science.gov (United States)

Chakraborty, S.; Boolchand, P.

2011-03-01

Reversibility windows have been observed in modified oxides (alkali-silicates and -germanates) and identified with Intermediate Phases(IPs). Here we find preliminary evidence of an IP in a ternary oxide glass, (B2 O3)5 (Te O2)95-x (V2O5)x , which is composed of network formers. Bulk glasses are synthesized across the 18% x 35 % composition range, and examined in Raman scattering, modulated DSC and molar volume experiments. Glass transition temperatures Tg (x) steadily decrease with V2O5 content x, and reveal the enthalpy of relaxation at Tg to show a global minimum in the 24% x < 27 range, the reversibility window (IP). Molar volumes reveal a minimum in this window. Raman scattering reveals a Boson mode, and at least six other vibrational bands in the 100cm-1 < ν < 1700cm-1 range. Compositional trends in vibrational mode strengths and frequency are established. These results will be presented in relation to glass structure evolution with vanadia content and the underlying elastic phases. Supported by NSF grant DMR 08-53957.

Effect of surface oxidation on the nm-scale wear behavior of a metallic glass

International Nuclear Information System (INIS)

Caron, A.; Louzguine-Luzguin, D. V.; Sharma, P.; Inoue, A.; Shluger, A.; Fecht, H.-J.

2011-01-01

Metallic glasses are good candidates for applications in micromechanical systems. With size reduction of mechanical components into the micrometer and submicrometer range, the native surface oxide layer starts playing an important role in contact mechanical applications of metallic glasses. We use atomic force microscopy to investigate the wear behavior of the Ni 62 Nb 38 metallic glass with a native oxide layer and with an oxide grown after annealing in air. After the annealing, the wear rate is found to have significantly decreased. Also the dependency of the specific wear on the velocity is found to be linear in the case of the as spun sample while it follows a power law in the case of the sample annealed in air. We discuss these results in relation to the friction behavior and properties of the surface oxide layer obtained on the same alloy.

Photoelectrochemical performance of Mn-TiO{sub 2} thin films mounted on FTO prepared by sol-gel spin coating

Energy Technology Data Exchange (ETDEWEB)

Chen, J.C.; Song, G.H. [National Central Univ., Taoyuan, Taiwan (China). Dept. of Mechanical Engineering; Lu, C.W. [Jen-Teh Junior College, Hou- Lung, Taiwan (China). Dept. of Information Management; Tseng, C.J. [National Central Univ., Chung-Li, Taoyuan County, Taiwan (China). Dept. of Mechanical Engineering; Cheng, K.W. [Chang Gung Univ., Tao-Yuan, Taiwan (China). Dept. of Chemical and Materials Engineering

2009-07-01

Tin oxide (TiO{sub 2}) sol-gels with Mn{sup 2+} molar ratios ranging from 0 to 0.1 per cent were used to form nano-structured Mn(x)Ti(1-x)O(2) thin films. A layer-by-layer spincoating (LLSC) technique was used, in which 10 very thin and uniform coating layers of Mn(x)Ti(1-x)O(2) were deposited on fluorine doped tin oxide (FTO) glass. Properties of the thin films were determined as a function of annealing temperature and molar ratio of the Mn{sup 2+} ions by X-ray diffraction (XRD), scanning electron microscopy (SEM), Atomic Force microscopy (AFM) and photoelectrochemical (PEC) measurements. The PEC measurements were obtained in a dry-type three-electrode cell consisting of sample, platinized and reference Ag/AgCl electrodes. The results revealed that the Mn(x)Ti(1-x)O(2) thin films have better structure and electrochemical characteristics when the annealing temperature is 550 degrees C. The TiO{sub 2} thin films with Mn{sup 2+} ions also had higher photocurrent than undoped TiO{sub 2}. The optimum Mn{sup 2+} loading in this study was found to be 0.1 ml per cent. The maximum photocurrent of Mn(0.1)Ti(0.9)O(2) thin films is about 0.68 mA/cm2 when the bias potential is 0.8 V (vs.Ag/AgCl).

Effect of Magnesium Oxide Nanoparticles on Water Glass Structure

Directory of Open Access Journals (Sweden)

Bobrowski A.

2012-09-01

Full Text Available An attempt has been made to determine the effect of an addition of colloidal suspensions of the nanoparticles of magnesium oxide on the structure of water glass, which is a binder for moulding and core sands. Nanoparticles of magnesium oxide MgO in propanol and ethanol were introduced in the same mass content (5wt.% and structural changes were determined by measurement of the FT-IR absorption spectra.

Signatures of natural selection at the FTO (fat mass and obesity associated locus in human populations.

Directory of Open Access Journals (Sweden)

Xuanshi Liu

Full Text Available Polymorphisms in the first intron of FTO have been robustly replicated for associations with obesity. In the Sorbs, a Slavic population resident in Germany, the strongest effect on body mass index (BMI was found for a variant in the third intron of FTO (rs17818902. Since this may indicate population specific effects of FTO variants, we initiated studies testing FTO for signatures of selection in vertebrate species and human populations.First, we analyzed the coding region of 35 vertebrate FTO orthologs with Phylogenetic Analysis by Maximum Likelihood (PAML, ω = dN/dS to screen for signatures of selection among species. Second, we investigated human population (Europeans/CEU, Yoruba/YRI, Chinese/CHB, Japanese/JPT, Sorbs SNP data for footprints of selection using DnaSP version 4.5 and the Haplotter/PhaseII. Finally, using ConSite we compared transcription factor (TF binding sites at sequences harbouring FTO SNPs in intron three.PAML analyses revealed strong conservation in coding region of FTO (ω<1. Sliding-window results from population genetic analyses provided highly significant (p<0.001 signatures for balancing selection specifically in the third intron (e.g. Tajima's D in Sorbs = 2.77. We observed several alterations in TF binding sites, e.g. TCF3 binding site introduced by the rs17818902 minor allele.Population genetic analysis revealed signatures of balancing selection at the FTO locus with a prominent signal in intron three, a genomic region with strong association with BMI in the Sorbs. Our data support the hypothesis that genes associated with obesity may have been under evolutionary selective pressure.

A study on linear and non-linear optical constants of Rhodamine B thin film deposited on FTO glass

Science.gov (United States)

Yahia, I. S.; Jilani, Asim; Abutalib, M. M.; AlFaify, S.; Shkir, M.; Abdel-wahab, M. Sh.; Al-Ghamdi, Attieh A.; El-Naggar, A. M.

2016-06-01

The aim of this research was to fabricate/deposit the good quality thin film of Rhodamine B dye on fluorine doped tin oxide glass substrate by the low cost spin coating technique and study their linear and nonlinear optical parameters. The thickness of the thin film was measured about 300 nm with alpha step system. The transmittance of the fabricated thin film was found to be above 75% corresponding to the fluorine doped tin oxide layer. The structural analysis was performed with X-rays diffraction spectroscopy. Atomic force microscope showed the topographic image of deposited thin film. Linear optical constant like absorption coefficient, band gap, and extinction index was calculated. The dielectric constant was calculated to know the optical response of Rhodamine B dye over fluorine doped tin oxide substrate. The nonlinear optical constant like linear optical susceptibility χ(1), nonlinear optical susceptibility χ(3), nonlinear refractive index (n2) were calculated by spectroscopic method. This method has advantage over the experimental method like Z-Scan for organic dye base semiconductors for future advance optoelectronics applications like dye synthesis solar cell.

REACTION PRODUCTS AND CORROSION OF MOLYBDENUM ELECTRODE IN GLASS MELT CONTAINING ANTIMONY OXIDES AND SODIUM SULFATE

Directory of Open Access Journals (Sweden)

JIŘÍ MATĚJ

2012-09-01

Full Text Available The products on the interface of a molybdenum electrode and glass melt were investigated primarily at 1400°C in three model glass melts without ingredients, with 1 % Sb2O3 and with 1 % Sb2O3 and 0.5 % SO3 (wt. %, both under and without load by alternating current. Corrosion of the molybdenum electrode in glass melt without AC load is higher by one order of magnitude if antimony oxides are present. The corrosion continues to increase if sulfate is present in addition to antimony oxides. Isolated antimony droplets largely occur on the electrode-glass melt interface, and numerous droplets are also dissipated in the surrounding glass if only antimony oxides are present in the glass melt. A comparatively continuous layer of antimony occurs on the interface if SO3 is also present, antimony being always in contact with molybdenum sulfide. Almost no antimony droplets are dissipated in the glass melt. The total amount of precipitated antimony also increases. The presence of sulfide on the interface likely facilitates antimony precipitation. The reaction of molybdenum with antimony oxides is inhibited in sites covered by an antimony layer. The composition of sulfide layers formed at 1400°C approximates that of Mo2S3. At 1100°C, the sulfide composition approximates that of MoS4. Corrosion multiplies in the glass melt without additions through the effect of AC current, most molybdenum being separated in the form of metallic particles. Corrosion also increases in the glass melt containing antimony oxides. This is due to increased corrosion in the neighborhood of the separated antimony droplets. This mechanism also results in the loosening of molybdenum particles. The amount of precipitated antimony also increases through the effect of the AC current. AC exerts no appreciable effect on either corrosion, the character of the electrode-glass interface, or antimony precipitation in the glass melt containing SO3.

Associations between FTO genotype and total energy and macronutrient intake in adults: A systematic review and meta-analysis

NARCIS (Netherlands)

Livingstone K.M.; Celis-Morales C.; Lara J.; Ashor A.W.; Lovegrove J.A.; Martinez J.A.; Saris W.H.; Gibney M.; Manios Y.; Traczyk I.; Drevon C.A.; Daniel H.; Gibney E.R.; Brennan L.; Bouwman J.; Grimaldi K.A.; Mathers J.C.

2015-01-01

Risk variants of fat mass and obesity-associated (FTO) gene have been associated with increased obesity. However, the evidence for associations between FTO genotype and macronutrient intake has not been reviewed systematically. Our aim was to evaluate the potential associations between FTO genotype

Optical Properties and Electrochemical Performance of LiFePO4 Thin Films Deposited on Transparent Current Collectors.

Science.gov (United States)

Lee, HyunSeok; Yim, Haena; Kim, Kwang-Bum; Choi, Ji-Won

2015-11-01

LiFePO4 thin film cathodes are deposited on various transparent conducting oxide thin films on glass, which are used as cathode current collectors. The XRD patterns show that the thin films have the phase of LiFePO4 with an ordered olivine structure indexed to the orthorhombic Pmna space group. LiFePO4 thin film deposited on various TCO glass substrates exhibits transmittance of about 53%. The initial specific discharge capacities of LiFePO4 thin films are 25.0 μAh/cm2 x μm on FTO, 33.0 μAh/cm2 x μm on ITO, and 13.0 μAh/cm2 x μm on AZO coated glass substrates. Interestingly, the retention capacities of LiFePO4 thin films are 76.0% on FTO, 31.2% on ITO, and 37.7% on AZO coated glass substrates at 20th cycle. The initial specific discharge capacity of the LiFePO4/FTO electrode is slightly lower, but the discharge capacities of the LiFePO4/FTO electrode relatively decrease less than those of the others such as LiFePO4/ITO and LiFePO4/AZO with cycling. The results reported here provide the high transparency of LiFePO4 thin films cathode materials and the good candidate as FTO current collector of the LiFePO4 thin film cathode of transparent thin film rechargeable batteries due to its high transparency and cyclic retention.

A Glass-Ceramic Waste Forms for the Immobilization of Rare Earth Oxides from the Pyroprocessing Waste salt

International Nuclear Information System (INIS)

Ahn, Byung-Gil; Park, Hwan-Seo; Kim, Hwan-Young; Kim, In-Tae

2008-01-01

The fission product of rare earth (RE) oxide wastes are generates during the pyroprocess . Borosilicate glass or some ceramic materials such as monazite, apatite or sodium zirconium phosphate (NZP) have been a prospective host matrix through lots of experimental results. Silicate glasses have long been the preferred waste form for the immobilization of HLW. In immobilization of the RE oxides, the developed process on an industrial scale involves their incorporation into a glass matrix, by melting under 1200 ∼ 1300 .deg. C. Instead of the melting process, glass powder sintering is lower temperature (∼ 900 .deg. C) required for the process which implies less demanding conditions for the equipment and a less evaporation of volatile radionuclides. This study reports the behaviors, direct vitrification of RE oxides with glass frit, glass powder sintering of REceramic with glass frit, formation of RE-apatite (or REmonazite) ceramic according to reaction temperature, and the leach resistance of the solidified waste forms

Nanotextured Spikes of α-Fe2O3/NiFe2O4 Composite for Efficient Photoelectrochemical Oxidation of Water.

Science.gov (United States)

Hussain, Shabeeb; Tavakoli, Mohammad Mahdi; Waleed, Aashir; Virk, Umar Siddique; Yang, Shihe; Waseem, Amir; Fan, Zhiyong; Nadeem, Muhammad Arif

2018-03-27

We demonstrate for the first time the application of p-NiFe 2 O 4 /n-Fe 2 O 3 composite thin films as anode materials for light-assisted electrolysis of water. The p-NiFe 2 O 4 /n-Fe 2 O 3 composite thin films were deposited on planar fluorinated tin oxide (FTO)-coated glass as well as on 3D array of nanospike (NSP) substrates. The effect of substrate (planar FTO and 3D-NSP) and percentage change of each component (i.e., NiFe 2 O 4 and Fe 2 O 3 ) of composite was studied on photoelectrochemical (PEC) water oxidation reaction. This work also includes the performance comparison of p-NiFe 2 O 4 /n-Fe 2 O 3 composite (planar and NSP) devices with pure hematite for PEC water oxidation. Overall, the nanostructured p-NiFe 2 O 4 /n-Fe 2 O 3 device with equal molar 1:1 ratio of NiFe 2 O 4 and Fe 2 O 3 was found to be highly efficient for PEC water oxidation as compared with pure hematite, 1:2 and 1:3 molar ratios of composite. The photocurrent density of 1:1 composite thin film on planar substrate was equal to 1.07 mA/cm 2 at 1.23 V RHE , which was 1.7 times higher current density as compared with pure hematite device (0.63 mA/cm 2 at 1.23 V RHE ). The performance of p-NiFe 2 O 4 /n-Fe 2 O 3 composites in PEC water oxidation was further enhanced by their deposition over 3D-NSP substrate. The highest photocurrent density of 2.1 mA/cm 2 at 1.23 V RHE was obtained for the 1:1 molar ratio p-NiFe 2 O 4 /n-Fe 2 O 3 composite on NSP (NF1-NSP), which was 3.3 times more photocurrent density than pure hematite. The measured applied bias photon-to-current efficiency (ABPE) value of NF1-NSP (0.206%) was found to be 1.87 times higher than that of NF1-P (0.11%) and 4.7 times higher than that of pure hematite deposited on FTO-coated glass (0.044%). The higher PEC water oxidation activity of p-NiFe 2 O 4 /n-Fe 2 O 3 composite thin film as compared with pure hematite is attributed to the Z-path scheme and better separation of electrons and holes. The increased surface area and greater light

SiFTO: An Empirical Method for Fitting SN Ia Light Curves

Science.gov (United States)

Conley, A.; Sullivan, M.; Hsiao, E. Y.; Guy, J.; Astier, P.; Balam, D.; Balland, C.; Basa, S.; Carlberg, R. G.; Fouchez, D.; Hardin, D.; Howell, D. A.; Hook, I. M.; Pain, R.; Perrett, K.; Pritchet, C. J.; Regnault, N.

2008-07-01

We present SiFTO, a new empirical method for modeling Type Ia supernova (SN Ia) light curves by manipulating a spectral template. We make use of high-redshift SN data when training the model, allowing us to extend it bluer than rest-frame U. This increases the utility of our high-redshift SN observations by allowing us to use more of the available data. We find that when the shape of the light curve is described using a stretch prescription, applying the same stretch at all wavelengths is not an adequate description. SiFTO therefore uses a generalization of stretch which applies different stretch factors as a function of both the wavelength of the observed filter and the stretch in the rest-frame B band. We compare SiFTO to other published light-curve models by applying them to the same set of SN photometry, and demonstrate that SiFTO and SALT2 perform better than the alternatives when judged by the scatter around the best-fit luminosity distance relationship. We further demonstrate that when SiFTO and SALT2 are trained on the same data set the cosmological results agree. Based on observations obtained with MegaPrime/MegaCam, a joint project of CFHT and CEA/DAPNIA, at the Canada-France-Hawaii Telescope (CFHT) which is operated by the National Research Council (NRC) of Canada, the Institut National des Sciences de l'Univers of the Centre National de la Recherche Scientifique (CNRS) of France, and the University of Hawaii. This work is based in part on data products produced at the Canadian Astronomy Data Centre as part of the Canada-France-Hawaii Telescope Legacy Survey, a collaborative project of NRC and CNRS.

Improving the performance of fluorine-doped tin oxide by adding salt

Energy Technology Data Exchange (ETDEWEB)

Purwanto, Agus, E-mail: Aguspur@uns.ac.id [Department of Chemical Engineering, Faculty of Engineering, Sebelas Maret University, Jl. Ir. Sutami 36 A, Surakarta, Central Java 57126 (Indonesia); Widiyandari, Hendri [Department of Physics, Faculty of Sciences and Mathematics, Diponegoro University, Jl. Prof. Dr. Soedarto, Tembalang, Semarang 50275 (Indonesia); Suryana, Risa [Department of Physics, Faculty of Mathematics and Natural Sciences, Sebelas Maret University, Jl. Ir. Sutami 36 A, Surakarta, Central Java 57126 (Indonesia); Jumari, Arif [Department of Chemical Engineering, Faculty of Engineering, Sebelas Maret University, Jl. Ir. Sutami 36 A, Surakarta, Central Java 57126 (Indonesia)

2015-07-01

High-performance fluorine-doped tin oxide (FTO) films were fabricated via a spray deposition technique with salt added to the precursor. The addition of NaCl in the precursor improved the conductivity of the FTO films. Increasing the NaCl concentration to its optimal concentration reduced the sheet resistance of the FTO film. The optimal values for the addition of a NaCl were 0.5, 0.5, 1.5, and 1.5 at.% for the FTO film prepared using NH{sub 4}F concentration of 4, 10, 16, and 22 at.%, respectively. The lowest sheet resistance of the salt-added FTO film was 4.8 Ω/□. The FTO film averaged a transmittance of more than 80% in the visible range region (λ = 400–800 nm). XRD diffractograms confirmed that the crystal structure of the as-grown FTO film was that of a tetragonal SnO{sub 2} and that the addition of salt improved its crystallinity. This film has the potential for use as an electrode for dye-sensitized solar cells (DSSCs). - Highlights: • A method to improve FTO performance using the addition of salt • The FTO film exhibited high performance of conductivity and light transmittance. • This technique is low-cost, fast and scales-up easily using simple devices.

Liquidus temperature and chemical durability of selected glasses to immobilize rare earth oxides waste

Energy Technology Data Exchange (ETDEWEB)

Mohd Fadzil, Syazwani, E-mail: mfsyazwani86@postech.ac.kr [Division of Advanced Nuclear Engineering, Pohang University of Science and Technology, 790784 Pohang, Gyeongbuk (Korea, Republic of); School of Applied Physics, Faculty of Science and Technology, The National University of Malaysia, 43650 Bandar Baru Bangi, Selangor (Malaysia); Hrma, Pavel [Division of Advanced Nuclear Engineering, Pohang University of Science and Technology, 790784 Pohang, Gyeongbuk (Korea, Republic of); Pacific Northwest National Laboratory, P.O. Box 999, Richland, WA (United States); Schweiger, Michael J.; Riley, Brian J. [Pacific Northwest National Laboratory, P.O. Box 999, Richland, WA (United States)

2015-10-15

Pyroprocessing is are processing method for managing and reusing used nuclear fuel (UNF) by dissolving it in an electrorefiner with a molten alkali or alkaline earth chloride salt mixture while avoiding wet reprocessing. Pyroprocessing UNF with a LiCl–KCl eutectic salt releases the fission products from the fuel and generates a variety of metallic and salt-based species, including rare earth (RE) chlorides. If the RE-chlorides are converted to oxides, borosilicate glass is a prime candidate for their immobilization because of its durability and ability to dissolve almost any RE waste component into the glass matrix at high loadings. Crystallization that occurs in waste glasses as the waste loading increases may complicate glass processing and affect the product quality. This work compares three types of borosilicate glasses in terms of liquidus temperature (T{sub L}): the International Simple Glass designed by the International Working Group, sodium borosilicate glass developed by Korea Hydro and Nuclear Power, and the lanthanide aluminoborosilicate (LABS) glass established in the United States. The LABS glass allows the highest waste loadings (over 50 mass% RE{sub 2}O{sub 3}) while possessing an acceptable chemical durability. - Highlights: • We investigated crystallization in borosilicate glasses containing rare earth oxides. • New crystallinity and durability data are shown for glasses proposed in the literature. • Both liquidus temperature and chemical durability increased as the waste loading increased.

Scintillation property of rare earth-free SnO-doped oxide glass

OpenAIRE

Masai, Hirokazu; Yanagida, Takayuki; Fujimoto, Yutaka; Koshimizu, Masanori; Yoko, Toshinobu

2012-01-01

The authors have demonstrated scintillation of rare earth (RE)-free Sn-doped oxide glass by excitation of ionizing radiation. It is notable that light emission is attained for RE-free transparent glass due to s[2]-sp transition of Sn[2+] centre and the emission correlates with the excitation band at 20 eV. We have also demonstrated that excitation band of emission centre can be tuned by the chemical composition of the host glass. The present result is valuable not only for design of RE-free i...

Fabrication of high-performance fluorine doped-tin oxide film using flame-assisted spray deposition

Energy Technology Data Exchange (ETDEWEB)

Purwanto, Agus, E-mail: Aguspur@uns.ac.id [Department of Chemical Engineering, Faculty of Engineering, Sebelas Maret University, Jl. Ir. Sutami 36 A, Surakarta, Central Java 57126 (Indonesia); Widiyandari, Hendri [Department of Physics, Faculty of Mathematics and Natural Sciences, Diponegoro University, Jl. Prof. Dr. Soedarto, Tembalang, Semarang 50275 (Indonesia); Jumari, Arif [Department of Chemical Engineering, Faculty of Engineering, Sebelas Maret University, Jl. Ir. Sutami 36 A, Surakarta, Central Java 57126 (Indonesia)

2012-01-01

A high-performance fluorine-doped tin oxide (FTO) film was fabricated by flame-assisted spray deposition method. By varying the NH{sub 4}F doping concentration, the optimal concentration was established as 8 at.%. X-ray diffractograms confirmed that the as-grown FTO film was tetragonal SnO{sub 2}. In addition, the FTO film was comprised of nano-sized grains ranging from 40 to 50 nm. The heat-treated FTO film exhibited a sheet resistance of 21.8 {Omega}/{open_square} with an average transmittance of 81.9% in the visible region ({lambda} = 400-800 nm). The figures of merit shows that the prepared FTO film can be used for highly efficient dye-sensitized solar cells electrodes.

Effects of Oxidation and fractal surface roughness on the wettability and critical heat flux of glass-peened zirconium alloy tubes

International Nuclear Information System (INIS)

Fong, R.W.L.; Nitheanandan, T.; Bullock, C.D.; Slater, L.F.; McRae, G.A.

2003-05-01

Glass-bead peening the outside surfaces of zirconium alloy tubes has been shown to increase the Critical Heat Flux (CHF) in pool boiling of water. The CHF is found to correlate with the fractal roughness of the metal tube surfaces. In this study on the effect of oxidation on glass-peened surfaces, test measurements for CHF, surface wettability and roughness have been evaluated using various glass-peened and oxidized zirconium alloy tubes. The results show that oxidation changes the solid-liquid contact angle (i.e., decreases wettability of the metal-oxide surface), but does not change the fractal surface roughness, appreciably. Thus, oxidation of the glass-peened surfaces of zirconium alloy tubes is not expected to degrade the CHF enhancement obtained by glass-bead peening. (author)

Raman scattering boson peak and differential scanning calorimetry studies of the glass transition in tellurium-zinc oxide glasses.

Science.gov (United States)

Stavrou, E; Tsiantos, C; Tsopouridou, R D; Kripotou, S; Kontos, A G; Raptis, C; Capoen, B; Bouazaoui, M; Turrell, S; Khatir, S

2010-05-19

Raman scattering and differential scanning calorimetry (DSC) measurements have been carried out on four mixed tellurium-zinc oxide (TeO(2))(1 - x)(ZnO)(x) (x = 0.1, 0.2, 0.3, 0.4) glasses under variable temperature, with particular attention being given to the respective glass transition region. From the DSC measurements, the glass transition temperature T(g) has been determined for each glass, showing a monotonous decrease of T(g) with increasing ZnO content. The Raman study is focused on the low-frequency band of the glasses, the so-called boson peak (BP), whose frequency undergoes an abrupt decrease at a temperature T(d) very close to the respective T(g) values obtained by DSC. These results show that the BP is highly sensitive to dynamical effects over the glass transition and provides a means for an equally reliable (to DSC) determination of T(g) in tellurite glasses and other network glasses. The discontinuous temperature dependence of the BP frequency at the glass transition, along with the absence of such a behaviour by the high-frequency Raman bands (due to local atomic vibrations), indicates that marked changes of the medium range order (MRO) occur at T(g) and confirms the correlation between the BP and the MRO of glasses.

Raman scattering boson peak and differential scanning calorimetry studies of the glass transition in tellurium-zinc oxide glasses

International Nuclear Information System (INIS)

Stavrou, E; Tsiantos, C; Tsopouridou, R D; Kripotou, S; Kontos, A G; Raptis, C; Capoen, B; Bouazaoui, M; Turrell, S; Khatir, S

2010-01-01

Raman scattering and differential scanning calorimetry (DSC) measurements have been carried out on four mixed tellurium-zinc oxide (TeO 2 ) 1-x (ZnO) x (x = 0.1, 0.2, 0.3, 0.4) glasses under variable temperature, with particular attention being given to the respective glass transition region. From the DSC measurements, the glass transition temperature T g has been determined for each glass, showing a monotonous decrease of T g with increasing ZnO content. The Raman study is focused on the low-frequency band of the glasses, the so-called boson peak (BP), whose frequency undergoes an abrupt decrease at a temperature T d very close to the respective T g values obtained by DSC. These results show that the BP is highly sensitive to dynamical effects over the glass transition and provides a means for an equally reliable (to DSC) determination of T g in tellurite glasses and other network glasses. The discontinuous temperature dependence of the BP frequency at the glass transition, along with the absence of such a behaviour by the high-frequency Raman bands (due to local atomic vibrations), indicates that marked changes of the medium range order (MRO) occur at T g and confirms the correlation between the BP and the MRO of glasses.

Production of core–shell type conducting FTO/TiO2 photoanode for dye sensitized solar cells

International Nuclear Information System (INIS)

Icli, Kerem Cagatay; Yavuz, Halil Ibrahim; Ozenbas, Macit

2014-01-01

Core–shell type photoanode composed of electrically conducting fluorine doped tin dioxide (FTO) matrix and TiO 2 shell layer was prepared and applied in dye sensitized solar cells. Effects of fluorine doping on tin dioxide based cells and precursor material on shell layer were investigated. Fluorine doped tin dioxide nanoparticles were synthesized under hydrothermal conditions and resistivity value down to 17 Ω cm was achieved. Cells constructed from FTO nanoparticles show enhanced performance compared to intrinsic SnO 2 . Deposition of thin blocking TiO 2 layers was conducted using ammonium hexafluorotitanate and titanium tetrachloride aqueous solutions for different dipping durations which yielded significant deviations in the layer morphology and affected cell parameters. Best results were obtained with titanium tetrachloride treated cells giving 11.51 mA/cm 2 photocurrent density and they were comparable with that of pure TiO 2 based cells prepared under identical conditions. - Graphical abstract: Core shell type FTO matrix was formed as TiO 2 is the shell material to create a blocking layer between FTO core and the electrolyte for suppressed recombination and efficiency enhancement. Display Omitted - Highlights: • Core–shell type photoanode using conducting FTO matrix and TiO 2 shell was prepared. • FTO nanoparticles having resistivity value down to 17 Ω cm was achieved. • Best cell parameters were obtained with TiCl 4 treated cells. • FTO nanoparticle based cells show enhanced performance compared to intrinsic SnO 2 . • Photocurrent in TiCl 4 treated cells is found as comparable to pure TiO 2 cell

Production and remediation of low sludge simulated Purex waste glasses, 2: Effects of sludge oxide additions on glass durability

International Nuclear Information System (INIS)

Ramsey, W.G.

1993-01-01

Glass produced during the Purex 4 campaigns of the Integrated DWPF Melter System (IDMS) and the 774 Research Melter contained a lower fraction of sludge components than targeted by the Product Composition Control System (PCCS). Purex 4 glass was more durable than the benchmark (EA) glass, but was less durable than most other simulated SRS high-level waste glasses. Further, the measured durability of Purex 4 glass was not as well correlated with the durability predicted from the DWPF process control algorithm, probably because the algorithm was developed to predict the durability of SRS high-level waste glasses with higher sludge content than Purex 4. A melter run, designated Purex 4 Remediation, was performed using the 774 Research Melter to determine if the initial PCCS target composition determined for Purex 4 would produce acceptable glass whose durability could be accurately modeled by the DWPF glass durability algorithm. Reagent grade oxides and carbonates were added to Purex 4 melter feed stock to simulate a higher sludge loading. Each canister of glass produced was sampled and the glass durability was determined by the Product Consistency Test method. This document details the durability data and subsequent analysis

Physical activity modifies the FTO effect on BMI change in Japanese adolescents.

Science.gov (United States)

Shinozaki, Keiko; Okuda, Masayuki; Okayama, Naoko; Kunitsugu, Ichiro

2018-04-14

Evidence of the effects of fat mass and obesity-associated (FTO) gene variation and long-term effects of physical activity (PA) on adiposity in adolescents is largely scarce. This study aimed to investigate whether physical activity modulates the effects of the FTO gene on body mass index (BMI) changes in Japanese adolescents between the ages of 13 and 18 years. Data of 343 subjects (156 boys; 187 girls) who were enrolled in 2006 and 2007 from schools on Shunan City, Japan, were collected. Genotyping (rs1558902) was conducted, and anthropometric measurements and blood test results were recorded for subjects in the eighth grade. A second survey involving self-reporting of anthropometric measurements was conducted when the subjects were in the twelfth grade. PA was estimated using the International Physical Activity Questionnaire in this survey. BMI and the standard deviation score for BMI (BMI-SDS) were calculated. BMI changes and BMI-SDS changes were compared among FTO genotypes using a multivariate model. The effect of the interaction between PA and the FTO genotype on BMI changes was significant among boys but not girls. Among boys, PA had a significant negative influence on BMI-SDS changes in those with the AA genotype and a significant positive influence on BMI and BMI-SDS changes in those with the TT genotype. These data suggest that the influence of PA on BMI changes and BMI-SDS changes varied on the basis of genotype. PA modified the effect of the FTO gene on BMI changes in Japanese boys. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Solid-state ionics: Studies of lithium-conducting sulfide glasses and a superconducting oxide compound

International Nuclear Information System (INIS)

Ahn, Byung Tae.

1989-01-01

The first part of this work studies lithium-conducting sulfide glasses for battery applications, while the second part studies the thermodynamic properties of a superconducting oxide compound by using an oxide electrolyte. Lithium conducting glasses based on the SiS 2 -Li 2 S system are possible solid electrolytes for high-energy-density lithium batteries. The foremost requirement for solid electrolytes is that they should have high ionic conductivities. Unfortunately, most crystalline lithium conductors have low ionic conductivities at room temperature. However, glass ionic conductors show higher ionic conductivities than do crystalline forms of the same material. In addition to higher ionic conductivities, glasses appear to have several advantages over crystalline materials. These advantages include isotropic conductivity, absence of grain boundary effects, ease of glass forming, and the potential for a wide range of stability to oxidizing and reducing conditions. Using pyrolitic graphite-coated quartz ampoules, new ternary compounds and glasses in the SiS 2 -Li 2 S system were prepared. Several techniques were used to characterize the materials: powder x-ray diffraction, differential thermal analysis, differential scanning calorimetry, and AC impedance spectroscopy. The measured lithium conductivity of the sulfide glasses was one of the highest among the known solid lithium conductors. Measuring the equilibrium open circuit voltages assisted in determining the electrochemical stabilities of the ternary compounds and glasses with respect to pure Li. A solid-state ionic technique called oxygen coulometric titration was used to measure the thermodynamic stability, the oxygen stoichiometry, and the effects of the oxygen stoichiometry, and the effects of the oxygen stoichiometry and the cooling rate on superconductivity of the YBa 2 Cu 3 O 7-x compound were investigated

A study on linear and non-linear optical constants of Rhodamine B thin film deposited on FTO glass

Energy Technology Data Exchange (ETDEWEB)

Yahia, I.S. [Nano-Science & Semiconductor Labs, Physics Department, Faculty of Education, Ain Shams University, Roxy, Cairo (Egypt); Department of Physics, Faculty of Science, King Khalid University, P.O. Box 9004, Abha (Saudi Arabia); Jilani, Asim, E-mail: asim.jilane@gmail.com [Centre of Nanotechnology, Physics Department-Faculty of Science-AL Faisaliah Campus, King Abdulaziz University, P.O. Box 80200, Jeddah 21589 (Saudi Arabia); Abutalib, M.M. [Centre of Nanotechnology, Physics Department-Faculty of Science-AL Faisaliah Campus, King Abdulaziz University, P.O. Box 80200, Jeddah 21589 (Saudi Arabia); AlFaify, S. [Nano-Science & Semiconductor Labs, Physics Department, Faculty of Education, Ain Shams University, Roxy, Cairo (Egypt); Shkir, M. [Department of Physics, Faculty of Science, King Khalid University, P.O. Box 9004, Abha (Saudi Arabia); Abdel-wahab, M.Sh.; Al-Ghamdi, Attieh A. [Centre of Nanotechnology, Physics Department-Faculty of Science-AL Faisaliah Campus, King Abdulaziz University, P.O. Box 80200, Jeddah 21589 (Saudi Arabia); El-Naggar, A.M. [Exploitation of Renewable Energy Applications in Saudi Arabia, Physics & Astronomy Department, College of Science, King Saud University, P.O.Box 2455, Riyadh 11451 (Saudi Arabia)

2016-06-01

The aim of this research was to fabricate/deposit the good quality thin film of Rhodamine B dye on fluorine doped tin oxide glass substrate by the low cost spin coating technique and study their linear and nonlinear optical parameters. The thickness of the thin film was measured about 300 nm with alpha step system. The transmittance of the fabricated thin film was found to be above 75% corresponding to the fluorine doped tin oxide layer. The structural analysis was performed with X-rays diffraction spectroscopy. Atomic force microscope showed the topographic image of deposited thin film. Linear optical constant like absorption coefficient, band gap, and extinction index was calculated. The dielectric constant was calculated to know the optical response of Rhodamine B dye over fluorine doped tin oxide substrate. The nonlinear optical constant like linear optical susceptibility χ{sup (1)}, nonlinear optical susceptibility χ{sup (3)}, nonlinear refractive index (n{sub 2}) were calculated by spectroscopic method. This method has advantage over the experimental method like Z-Scan for organic dye base semiconductors for future advance optoelectronics applications like dye synthesis solar cell.

Adhesion mapping of chemically modified and poly(ethylene oxide)-grafted glass surfaces

OpenAIRE

Jogikalmath, G.; Stuart, J.K.; Pungor, A.; Hlady, V.

1999-01-01

Two-dimensional mapping of the adhesion pull-off forces was used to study the origin of surface heterogeneity in the grafted poly(ethylene oxide) (PEO) layer. The variance of the pull-off forces measured over the μm-sized regions after each chemical step of modifying glass surfaces was taken to be a measure of the surface chemical heterogeneity. The attachment of γ-glycidoxypropyltrimethoxy silane (GPS) to glass decreased the pull-off forces relative to the clean glass and made the surface mo...

Effect of ZnO on phase emergence, microstructure and surface modifications of calcium phosphosilicate glass/glass-ceramics having iron oxide

Energy Technology Data Exchange (ETDEWEB)

Sharma, K.; Dixit, A.; Bhattacharya, S.; Jagannath [Technical Physics and Prototype Engineering Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Deo, M.N. [High Pressure Physics Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Kothiyal, G.P., E-mail: gpkoth@barc.gov.in [Technical Physics and Prototype Engineering Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India)

2010-03-01

The effect of ZnO on phase emergence and microstructure properties of glass and glass-ceramics with composition 25SiO{sub 2}-50CaO-15P{sub 2}O{sub 5}-(10 - x)Fe{sub 2}O{sub 3}-xZnO (where x = 0, 2, 5, 7 mol%) has been studied. They have been characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). Surface modifications of these glass-ceramics in simulated body fluid have been studied using Fourier transform infrared reflection spectroscopy (FTIR), XPS and SEM. Results have shown a decrease in the fraction of non-bridging oxygen with increase in zinc oxide content. Emergence of crystalline phases in glass-ceramics at different heat treatment temperatures was studied using XRD. When glass is heat treated at 800 deg. C calcium phosphate, hematite and magnetite are developed as major phases in the glass-ceramics samples with ZnO up to 5 mol%. In addition to these, calcium silicate (Ca{sub 3}Si{sub 2}O{sub 7}) phase is also observed when glass is heat treated at 1000 deg. C. The microstructure of the glass-ceramics heat treated at 800 deg. C exhibits the formation of nano-size (40-50 nm) grains. On heat treatment at 1000 deg. C crystallites grow to above 50 nm size and more than one phase are observed in the microstructure. The formation of thin flake-like structure with coarse particles is observed at high zinc oxide concentration (x = 7 mol%). In vitro studies have shown the surface modifications and formation of Ca-P-rich layer on the glass-ceramics when immersed in simulated body fluids (SBF) for different durations. The bioactive response was found to depend on ZnO content.

Effect of ZnO on phase emergence, microstructure and surface modifications of calcium phosphosilicate glass/glass-ceramics having iron oxide

International Nuclear Information System (INIS)

Sharma, K.; Dixit, A.; Bhattacharya, S.; Jagannath; Deo, M.N.; Kothiyal, G.P.

2010-01-01

The effect of ZnO on phase emergence and microstructure properties of glass and glass-ceramics with composition 25SiO 2 -50CaO-15P 2 O 5 -(10 - x)Fe 2 O 3 -xZnO (where x = 0, 2, 5, 7 mol%) has been studied. They have been characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). Surface modifications of these glass-ceramics in simulated body fluid have been studied using Fourier transform infrared reflection spectroscopy (FTIR), XPS and SEM. Results have shown a decrease in the fraction of non-bridging oxygen with increase in zinc oxide content. Emergence of crystalline phases in glass-ceramics at different heat treatment temperatures was studied using XRD. When glass is heat treated at 800 deg. C calcium phosphate, hematite and magnetite are developed as major phases in the glass-ceramics samples with ZnO up to 5 mol%. In addition to these, calcium silicate (Ca 3 Si 2 O 7 ) phase is also observed when glass is heat treated at 1000 deg. C. The microstructure of the glass-ceramics heat treated at 800 deg. C exhibits the formation of nano-size (40-50 nm) grains. On heat treatment at 1000 deg. C crystallites grow to above 50 nm size and more than one phase are observed in the microstructure. The formation of thin flake-like structure with coarse particles is observed at high zinc oxide concentration (x = 7 mol%). In vitro studies have shown the surface modifications and formation of Ca-P-rich layer on the glass-ceramics when immersed in simulated body fluids (SBF) for different durations. The bioactive response was found to depend on ZnO content.

Indentation Behavior of Permanently Densified Oxide Glasses

DEFF Research Database (Denmark)

Bechgaard, Tobias Kjær; Januchta, Kacper; Kapoor, Saurabh

-induced changes in density, structure, and indentation behavior of a range of oxide glasses, including silicates, borates, and phosphates. The effect of compression on the structure is analyzed through both Raman and NMR spectroscopy, while the mechanical properties are investigated using Vickers micro......Hot isostatic compression can be used as a post treatment method to tune the properties of glass materials as well as to obtain improved understanding of the pressure-induced structural changes and densification mechanisms, e.g., during sharp contact loading. Here, we review the pressure......-indentation. The magnitude of the changes in all macroscopic properties (e.g., density, hardness, and crack resistance) is found to correlate well with the magnitude and type of structural change induced by hot compression. We show that the structural changes depend largely on the type of network former, the coordination...

Dietary energy density affects fat mass in early adolescence and is not modified by FTO variants.

Directory of Open Access Journals (Sweden)

Laura Johnson

Full Text Available Dietary energy density (DED does not have a simple linear relationship to fat mass in children, which suggests that some children are more susceptible than others to the effects of DED. Children with the FTO (rs9939609 variant that increases the risk of obesity may have a higher susceptibility to the effects of DED because their internal appetite control system is compromised. We tested the relationship between DED and fat mass in early adolescence and its interaction with FTO variants.We carried out a prospective analysis on 2,275 children enrolled in the Avon Longitudinal Study of Parents and Children (ALSPAC. Diet was assessed at age 10 y using 3-day diet diaries. DED (kJ/g was calculated excluding drinks. Children were genotyped for the FTO (rs9939609 variant. Fat mass was estimated at age 13 y using the Lunar Prodigy Dual-energy X-ray Absorptiometry scanner. There was no evidence of interaction between DED at age 10 y and the high risk A allele of the FTO gene in relation to fat mass at age 13 y (beta = 0.005, p = 0.51, suggesting that the FTO gene has no effect on the relation between DED at 10 y and fat mass at 13 y. When DED at 10 y and the A allele of FTO were in the same model they were independently related to fat mass at 13 y. Each A allele of FTO was associated with 0.35+/-0.13 kg more fat mass at 13 y and each 1 kJ/g DED at 10 y was associated with 0.16+/-0.06 kg more fat mass at age 13 y, after controlling for misreporting of energy intake, gender, puberty, overweight status at 10 y, maternal education, TV watching, and physical activity.This study reveals the multi-factorial origin of obesity and indicates that although FTO may put some children at greater risk of obesity, encouraging a low dietary energy density may be an effective strategy to help all children avoid excessive fat gain.

Low physical activity accentuates the effect of the FTO rs9939609 polymorphism on body fat accumulation

DEFF Research Database (Denmark)

Andreasen, Camilla H; Stender-Petersen, Kirstine L; Mogensen, Mette S

2008-01-01

(-16)). Furthermore, obesity-related quantitative traits such as body weight, waist circumference, fat mass, and fasting serum leptin levels were significantly elevated in A-allele carriers. An interaction between the FTO rs9939609 genotype and physical activity (P = 0.007) was found, where physically inactive...... homozygous risk A-allele carriers had a 1.95 +/- 0.3 kg/m(2) increase in BMI compared with homozygous T-allele carriers. CONCLUSIONS: We validate that variation in FTO is associated with type 2 diabetes when not adjusted for BMI and with an overall increase in body fat mass. Furthermore, low physical......OBJECTIVE: Three independent studies have shown that variation in the fat mass and obesity-associated (FTO) gene associates with BMI and obesity. In the present study, the effect of FTO variation on metabolic traits including obesity, type 2 diabetes, and related quantitative phenotypes...

ZnO/CdS bi-layer nanostructures photoelectrode for dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Dalal, Paresh V., E-mail: paresh10dalal@gmail.com [Physics Research Lab, Shri V. S. Naik Arts, Commerce and Science College, Raver-425508 (M. S.) (India); Deshpande, Milind P., E-mail: vishwadeshpande@yahoo.co.in [Department of Physics, Sardar Patel University, Vallabh Vidyanagar-388120 (Gujarat) (India); Solanki, Bharat G., E-mail: bhrt.solanki17@gmail.com; Soni, Saurabh S., E-mail: soni-b21@yahoo.co.in [Department of Chemistry, Sardar Patel University, Vallabh Vidyanagar-388120 (Gujarat) (India)

2016-05-06

Simple chemical deposition method for the synthesis of ZnO/CdS bilayer photoelectrode on fluorine doped tin oxide (FTO) coated glass substrate in aqueous medium at low temperature (< 373K) is described. The different preparative parameters such as deposition time, bath temperature, concentration of precursor solution and, pH of the bath etc. were optimized. Nanograined ZnO was deposited on FTO coated glass substrates by dip-coating method, whereas CdS nanorods were successfully synthesized on pre-deposited ZnO film by Chemical Bath Deposition (CBD) method. The Photovoltaic properties of FTO/ZnO/CdS bilayer photo electrodes were also studied. A maximum short circuit current density of 9.1 mA cm-2 and conversion efficiency 1.05% are observed for ZnO/CdS-10min. Layer, which supports fast electron injection kinetics due to hetero structured nanorod, while minimum values of 0.53mA cm-2 and 0.01% respectively are observed for only ZnO deposited layer.

Low temperature high density plasma nitriding of stainless steel molds for stamping of oxide glasses

Directory of Open Access Journals (Sweden)

Aizawa Tatsuhiko

2016-01-01

Full Text Available Various kinds of stainless steels have been widely utilized as a die for mold- and direct-stamping processes of optical oxide glasses. Since they suffered from high temperature transients and thermal cycles in practice, they must be surface-treated by dry and wet coatings, or, by plasma nitriding. Martensitic stainless steel mold was first wet plated by the nickel phosphate (NiP, which was unstable at the high temperature stamping condition; and, was easy to crystalize or to fracture by itself. This issue of nuisance significantly lowered the productivity in fabrication of optical oxide-glass elements. In the present paper, the stainless steel mold was surface-treated by the low-temperature plasma nitriding. The nitrided layer by this surface modification had higher nitrogen solute content than 4 mass%; the maximum solid-solubility of nitrogen is usually 0.1 mass% in the equilibrium phase diagram. Owing to this solid-solution with high nitrogen concentration, the nitrided layer had high hardness over 1400 HV within its thickness of 50 μm without any formation of nitrides after plasma nitriding at 693 K for 14.4 ks. This plasma-nitrided mold was utilized for mold-stamping of two colored oxide glass plates at 833 K; these plates were successfully deformed and joined into a single glass plate by this stamping without adhesion or galling of oxide glasses onto the nitrided mold surface.

FTO at rs9939609, Food Responsiveness, Emotional Control and Symptoms of ADHD in Preschool Children

NARCIS (Netherlands)

F.P. Velders (Fleur); F.R.C. de Wit (Frank); P.W. Jansen (Pauline); V.W.V. Jaddoe (Vincent); A. Hofman (Albert); F.C. Verhulst (Frank); H.W. Tiemeier (Henning)

2012-01-01

textabstractThe FTO minor allele at rs9939609 has been associated with body mass index (BMI: weight (kg)/height (m)2) in children from 5 years onwards, food intake, and eating behaviour. The high expression of FTO in the brain suggests that this gene may also be associated with behavioural

Preparation of lead oxide nanoparticles from cathode-ray tube funnel glass by self-propagating method.

Science.gov (United States)

Wang, Yu; Zhu, Jianxin

2012-05-15

This paper presents a novel process of extracting lead oxide nanoparticles from cathode-ray tube (CRT) funnel glass using self-propagating high-temperature synthesis (SHS) method. The impacts of added amount of funnel glass on the extraction ratio of lead, the lead extraction velocity and the micromorphology, as well as particle size of extracted nanoparticles were investigated. We found that self-propagating reaction in the presence of Mg and Fe(2)O(3) could separate lead preferentially and superfine lead oxide nanoparticles were obtained from a collecting chamber. The separation ratio was related closely to the amount of funnel glass added in the original mixture. At funnel glass addition of no more than 40wt.%, over 90wt.% of lead was recovered from funnel glass. High extraction yield reveals that the network structure of funnel glass was fractured due to the dramatic energy generated during the SHS melting process. The PbO nanoparticles collected show good dispersion and morphology with a mean grain size of 40-50nm. Copyright © 2012 Elsevier B.V. All rights reserved.

Production of core–shell type conducting FTO/TiO{sub 2} photoanode for dye sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Icli, Kerem Cagatay [Micro and Nanotechnology Graduate Program, Middle East Technical University, Dumlupinar Bulvari, 06800 Ankara (Turkey); Center for Solar Energy Research and Applications (GUNAM), Middle East Technical University, Dumlupinar Bulvari, 06800 Ankara (Turkey); Yavuz, Halil Ibrahim [Center for Solar Energy Research and Applications (GUNAM), Middle East Technical University, Dumlupinar Bulvari, 06800 Ankara (Turkey); Department of Metallurgical and Materials Engineering, Middle East Technical University, Dumlupinar Bulvari, 06800 Ankara (Turkey); Ozenbas, Macit, E-mail: ozenbas@metu.edu.tr [Center for Solar Energy Research and Applications (GUNAM), Middle East Technical University, Dumlupinar Bulvari, 06800 Ankara (Turkey); Department of Metallurgical and Materials Engineering, Middle East Technical University, Dumlupinar Bulvari, 06800 Ankara (Turkey)

2014-02-15

Core–shell type photoanode composed of electrically conducting fluorine doped tin dioxide (FTO) matrix and TiO{sub 2} shell layer was prepared and applied in dye sensitized solar cells. Effects of fluorine doping on tin dioxide based cells and precursor material on shell layer were investigated. Fluorine doped tin dioxide nanoparticles were synthesized under hydrothermal conditions and resistivity value down to 17 Ω cm was achieved. Cells constructed from FTO nanoparticles show enhanced performance compared to intrinsic SnO{sub 2}. Deposition of thin blocking TiO{sub 2} layers was conducted using ammonium hexafluorotitanate and titanium tetrachloride aqueous solutions for different dipping durations which yielded significant deviations in the layer morphology and affected cell parameters. Best results were obtained with titanium tetrachloride treated cells giving 11.51 mA/cm{sup 2} photocurrent density and they were comparable with that of pure TiO{sub 2} based cells prepared under identical conditions. - Graphical abstract: Core shell type FTO matrix was formed as TiO{sub 2} is the shell material to create a blocking layer between FTO core and the electrolyte for suppressed recombination and efficiency enhancement. Display Omitted - Highlights: • Core–shell type photoanode using conducting FTO matrix and TiO{sub 2} shell was prepared. • FTO nanoparticles having resistivity value down to 17 Ω cm was achieved. • Best cell parameters were obtained with TiCl{sub 4} treated cells. • FTO nanoparticle based cells show enhanced performance compared to intrinsic SnO{sub 2}. • Photocurrent in TiCl{sub 4} treated cells is found as comparable to pure TiO{sub 2} cell.

Screening for coding variants in FTO and SH2B1 genes in Chinese patients with obesity.

Directory of Open Access Journals (Sweden)

Zhaojing Zheng

Full Text Available To investigate potential functional variants in FTO and SH2B1 genes among Chinese children with obesity.Sanger sequencing of PCR products of all FTO and SH2B1 exons and their flanking regions were performed in 338 Chinese Han children with obesity and 221 age- and sex-matched lean controls.A total of seven and five rare non-synonymous variants were identified in FTO and SH2B1, respectively. The overall frequencies of FTO and SH2B1 rare non-synonymous variants were similar in obese and lean children (2.37% and 0.90% vs. 1.81% and 1.36%, P>0.05. However, four out of the seven variants in FTO were novel and all were unique to obese children (p>0.05. None of the novel variants was consistently being predicted to be deleterious. Four out of five variants in SH2B1 were novel and one was unique to obese children (p>0.05. One variant (L293R that was consistently being predicted as deleterious in SH2B1 gene was unique to lean control. While rare missense mutations were more frequently detected in girls from obesity as well as lean control than boys, the difference was not statistically significant. In addition, it's shown that the prevalence of rare missense mutations of FTO as well as SH2B1 was similar across different ethnic groups.The rare missense mutations of FTO and SH2B1 did not confer risks of obesity in Chinese Han children in our cohort.

Electrochemical preparation of vertically aligned, hollow CdSe nanotubes and their p-n junction hybrids with electrodeposited Cu2O.

Science.gov (United States)

Debgupta, Joyashish; Devarapalli, Ramireddy; Rahman, Shakeelur; Shelke, Manjusha V; Pillai, Vijayamohanan K

2014-08-07

Vertically aligned, hollow nanotubes of CdSe are grown on fluorine doped tin oxide (FTO) coated glass substrates by ZnO nanowire template-assisted electrodeposition technique, followed by selective removal of the ZnO core using NH4OH. A detailed mechanism of nucleation and anisotropic growth kinetics of nanotubes have been studied by a combination of characterization tools such as chronoamperometry, SEM and TEM. Interestingly, "as grown" CdSe nanotubes (CdSe NTs) on FTO coated glass plates behave as n-type semiconductors exhibiting an excellent photo-response (with a generated photocurrent density value of ∼ 470 μA cm(-2)) while in contact with p-type Cu2O (p-type semiconductor, grown separately on FTO plates) because of the formation of a n-p heterojunction (type II). The observed photoresponse is 3 times higher than that of a similar device prepared with electrodeposited CdSe films (not nanotubes) and Cu2O on FTO. This has been attributed to the hollow 1-D nature of CdSe NTs, which provides enhanced inner and outer surface areas for better absorption of light and also assists faster transport of photogenerated charge carriers.

Enhanced Stem Cell Osteogenic Differentiation by Bioactive Glass Functionalized Graphene Oxide Substrates

Directory of Open Access Journals (Sweden)

Xiaoju Mo

2016-01-01

Full Text Available An unmet need in engineered bone regeneration is to develop scaffolds capable of manipulating stem cells osteogenesis. Graphene oxide (GO has been widely used as a biomaterial for various biomedical applications. However, it remains challenging to functionalize GO as ideal platform for specifically directing stem cell osteogenesis. Herein, we report facile functionalization of GO with dopamine and subsequent bioactive glass (BG to enhance stem cell adhesion, spreading, and osteogenic differentiation. On the basis of graphene, we obtained dopamine functionalized graphene oxide/bioactive glass (DGO/BG hybrid scaffolds containing different content of DGO by loading BG nanoparticles on graphene oxide surface using sol-gel method. To enhance the dispersion stability and facilitate subsequent nucleation of BG in GO, firstly, dopamine (DA was used to modify GO. Then, the modified GO was functionalized with bioactive glass (BG using sol-gel method. The adhesion, spreading, and osteoinductive effects of DGO/BG scaffold on rat bone marrow mesenchymal stem cells (rBMSCs were evaluated. DGO/BG hybrid scaffolds with different content of DGO could influence rBMSCs’ behavior. The highest expression level of osteogenic markers suggests that the DGO/BG hybrid scaffolds have great potential or elicit desired bone reparative outcome.

Designing heavy metal oxide glasses with threshold properties from network rigidity.

Science.gov (United States)

Chakraborty, Shibalik; Boolchand, P; Malki, M; Micoulaut, M

2014-01-07

Here, we show that a new class of glasses composed of heavy metal oxides involving transition metals (V2O5-TeO2) can surprisingly be designed from very basic tools using topology and rigidity of their underlying molecular networks. When investigated as a function of composition, such glasses display abrupt changes in network packing and enthalpy of relaxation at Tg, underscoring presence of flexible to rigid elastic phase transitions. We find that these elastic phases are fully consistent with polaronic nature of electronic conductivity at high V2O5 content. Such observations have new implications for designing electronic glasses which differ from the traditional amorphous electrolytes having only mobile ions as charge carriers.

Enhanced diode characteristics of organic solar cell with silanized fluorine doped tin oxide electrode

Science.gov (United States)

Sachdeva, Sheenam; Sharma, Sameeksha; Singh, Devinder; Tripathi, S. K.

2018-05-01

To investigate the diode characteristics of organic solar cell based on the planar heterojunction of 4,4'- cyclohexylidenebis[N,N-bis(4-methylphenyl)benzenamine] (TAPC) and fullerene (C70), we report the use of silanized fluorine-doped tin oxide (FTO) anode with N1-(3-trimethoxysilylpropyl)diethyltriamine (DETA) forming monolayer. The use of silanized FTO results in the decrease of saturation current density and diode ideality factor of the device. Such silanized FTO anode is found to enhance the material quality and improve the device properties.

Oxidation state of sulfur, iron and tin at the surface of float glasses

International Nuclear Information System (INIS)

Lagarde, P; Flank, A-M; Jupille, J; Montigaud, H

2009-01-01

Sulfur is an important element of glasses, not because of its amount, always very low (less than 0.4 % in weight of SO 3 ), but because of its role since it actively participates to the refinement process and, combined to other elements, it can be responsible for the coloration of the glass. Iron is also of a major importance in most of the glasses. In the case of the float glass, the two faces, because of the fabrication process, are different in terms of composition (presence of Sn for one face) and also in terms of oxidation state of these minority elements (Fe, Sn, S). There should be a subtle interplay between the concentrations and the oxidation states of these different minority elements, and anyway these variations occur over a thickness of the order of few micrometers below the surface. Using the high intensity and the focusing properties (3 x 3 μm 2 ) of the x-ray beam from the Lucia beamline, we have therefore studied the speciation of iron and sulfur near the face of a float glass in relation with the behavior of tin. This has been obtained by combining elemental x-ray fluorescence cartography and x-ray micro-absorption at the different K-edges.

Oxidation state of sulfur, iron and tin at the surface of float glasses

Energy Technology Data Exchange (ETDEWEB)

Lagarde, P; Flank, A-M [Synchrotron SOLEIL, l' Orme des Merisiers, BP 48 91192 Gif/Yvette cedex (France); Jupille, J [IMPMC, Universite P. and M. Curie, Campus de Boucicaut, 140 rue de Lourmel 75015 Paris (France); Montigaud, H [Saint-Gobain Recherche 39, quai Lucien Lefranc, BP 135 93303 Aubervilliers Cedex (France)

2009-11-15

Sulfur is an important element of glasses, not because of its amount, always very low (less than 0.4 % in weight of SO{sub 3}), but because of its role since it actively participates to the refinement process and, combined to other elements, it can be responsible for the coloration of the glass. Iron is also of a major importance in most of the glasses. In the case of the float glass, the two faces, because of the fabrication process, are different in terms of composition (presence of Sn for one face) and also in terms of oxidation state of these minority elements (Fe, Sn, S). There should be a subtle interplay between the concentrations and the oxidation states of these different minority elements, and anyway these variations occur over a thickness of the order of few micrometers below the surface. Using the high intensity and the focusing properties (3 x 3 {mu}m{sup 2}) of the x-ray beam from the Lucia beamline, we have therefore studied the speciation of iron and sulfur near the face of a float glass in relation with the behavior of tin. This has been obtained by combining elemental x-ray fluorescence cartography and x-ray micro-absorption at the different K-edges.

The FTO (fat mass and obesity associated gene codes for a novel member of the non-heme dioxygenase superfamily

Directory of Open Access Journals (Sweden)

Andrade-Navarro Miguel A

2007-11-01

Full Text Available Abstract Background Genetic variants in the FTO (fat mass and obesity associated gene have been associated with an increased risk of obesity. However, the function of its protein product has not been experimentally studied and previously reported sequence similarity analyses suggested the absence of homologs in existing protein databases. Here, we present the first detailed computational analysis of the sequence and predicted structure of the protein encoded by FTO. Results We performed a sequence similarity search using the human FTO protein as query and then generated a profile using the multiple sequence alignment of the homologous sequences. Profile-to-sequence and profile-to-profile based comparisons identified remote homologs of the non-heme dioxygenase family. Conclusion Our analysis suggests that human FTO is a member of the non-heme dioxygenase (Fe(II- and 2-oxoglutarate-dependent dioxygenases superfamily. Amino acid conservation patterns support this hypothesis and indicate that both 2-oxoglutarate and iron should be important for FTO function. This computational prediction of the function of FTO should suggest further steps for its experimental characterization and help to formulate hypothesis about the mechanisms by which it relates to obesity in humans.

Design of a visible light driven photo-electrochemical/electro-Fenton coupling oxidation system for wastewater treatment

International Nuclear Information System (INIS)

Ding, Xing; Ai, Zhihui; Zhang, Lizhi

2012-01-01

Highlights: ► Coupling PEC and EF oxidation significantly improves pollutant degradation efficiency. ► The degradation of the PEC/EF system was increased by 154%. ► The instantaneous current efficiency of the PEC/EF system was increased by 26%. - Abstract: In this study, we report on a photo-electrochemical/electro-Fenton oxidation (PEC/EF) system by coupling visible light driven photo-electrochemical oxidation (PEC) and electro-Fenton oxidation (EF) in an undivided cell. Bi 2 WO 6 nanoplates deposited on FTO glass (Bi 2 WO 6 /FTO) and Fe-Fe 2 O 3 core–shell nanowires supported on activated carbon fiber (Fe-Fe 2 O 3 /ACF) were used as the anode and the cathode in the PEC/EF system, respectively. This novel PEC/EF system showed much higher activity than the single PEC and EF systems on degradation of rhodamine B in aqueous solution at natural pH. Moreover, the degradation and the instantaneous current efficiencies of the PEC/EF system were increased by 154% and 26% in comparison with the sum of those of single PEC and EF systems, respectively. These significant enhancements could be attributed to the synergetic effect from better separation of photo-generated carriers in the photo-anode and the transfer of photo-electrons to the oxygen diffusion cathode to generate more electro-generated H 2 O 2 and hydroxyl radicals on the Fenton cathode. The better separation of photo-generated carriers contribute more to the overall degradation enhancement than the photo-electrons generated H 2 O 2 and the subsequent Fenton reaction on the cathode during the PEC/EF process.

Potential for microbial oxidation of ferrous iron in basaltic glass.

Science.gov (United States)

Xiong, Mai Yia; Shelobolina, Evgenya S; Roden, Eric E

2015-05-01

Basaltic glass (BG) is an amorphous ferrous iron [Fe(II)]-containing material present in basaltic rocks, which are abundant on rocky planets such as Earth and Mars. Previous research has suggested that Fe(II) in BG can serve as an energy source for chemolithotrophic microbial metabolism, which has important ramifications for potential past and present microbial life on Mars. However, to date there has been no direct demonstration of microbially catalyzed oxidation of Fe(II) in BG. In this study, three different culture systems were used to investigate the potential for microbial oxidation of Fe(II) in BG, including (1) the chemolithoautotrophic Fe(II)-oxidizing, nitrate-reducing "Straub culture"; (2) the mixotrophic Fe(II)-oxidizing, nitrate-reducing organism Desulfitobacterium frappieri strain G2; and (3) indigenous microorganisms from a streambed Fe seep in Wisconsin. The BG employed consisted of clay and silt-sized particles of freshly quenched lava from the TEB flow in Kilauea, Hawaii. Soluble Fe(II) or chemically reduced NAu-2 smectite (RS) were employed as positive controls to verify Fe(II) oxidation activity in the culture systems. All three systems demonstrated oxidation of soluble Fe(II) and/or structural Fe(II) in RS, whereas no oxidation of Fe(II) in BG material was observed. The inability of the Straub culture to oxidize Fe(II) in BG was particularly surprising, as this culture can oxidize other insoluble Fe(II)-bearing minerals such as biotite, magnetite, and siderite. Although the reason for the resistance of the BG toward enzymatic oxidation remains unknown, it seems possible that the absence of distinct crystal faces or edge sites in the amorphous glass renders the material resistant to such attack. These findings have implications with regard to the idea that Fe(II)-Si-rich phases in basalt rocks could provide a basis for chemolithotrophic microbial life on Mars, specifically in neutral-pH environments where acid-promoted mineral dissolution and

Self-cleaning glass coating containing titanium oxide and silicon

International Nuclear Information System (INIS)

Araujo, A.O. de; Alves, A.K.; Berutti, F.A.; Bergmann, C.P.

2009-01-01

Using the electro spinning technique nano fibers of titanium oxide doped with silicon were synthesized. As precursor materials, titanium propoxide, silicon tetra propoxide and a solution of polyvinylpyrrolidone were used. The non-tissue material obtained was characterized by X-ray diffraction to determine the phase and crystallite size, BET method to determine the surface and SEM to analyze the microstructure of the fibers. After ultrasound dispersion of this material in ethanol, the glass coatings were made by dip-coating methodology. The influence of the removal velocity, the solution composition and the glass surface preparation were evaluated. The film was characterized by the contact angle of a water droplet in its surface. (author)

Facing slag glass and slag glass ceramic produced from thermal power plant ash

Energy Technology Data Exchange (ETDEWEB)

Buruchenko, A.E.; Kolesnikov, A.A.; Lukoyanov, A.G.

1990-10-01

Evaluates properties of fly ash and slags from the Krasnoyarsk coal-fired power plants and their utilization for glass and ceramic glass production. Composition of a mixture of fly ash and slag was: silica 40-55%, aluminium oxides 10-40%, ferric trioxide 6-14%, calcium oxides 20-35%, magnesium oxides 3-6%, potassium oxides 0.3-1.5%, sodium oxides 0.2-05%, sulfur trioxide 0.9-5.0%. The analyzed fly ash and slags from the Krasnoyarsk plant were an economic waste material for glass production. Properties of sand, clay and other materials used in glass production and properties of glass and ceramic glass produced on the basis of fly ash and slags are analyzed. Economic aspects of fly ash and slag utilization are also evaluated. 3 refs.

Preparation of oxide glasses from metal alkoxides by sol-gel method

Science.gov (United States)

Kamiya, K.; Yoko, T.; Sakka, S.

1987-01-01

An investigation is carried out on the types of siloxane polymers produced in the course of the hydrolysis of silicon tetraethoxide, as well as the preparation of oxide glasses from metal alkoxides by the sol-gel method.

Seebeck coefficient of synthesized Titanium Dioxide thin film on FTO glass substrate

Science.gov (United States)

Usop, R.; Hamed, N. K. A.; Megat Hasnan, M. M. I.; Ikeda, H.; Sabri, M. F. M.; Ahmad, M. K.; Said, S. M.; Salleh, F.

2018-04-01

In order to fabricate a thermoelectric device on glass substrate for harvesting waste heat energy through house appliances, the Seebeck coefficient of translucent TiO2 thin film was investigated. The TiO2 thin film was synthesized by using hydrothermal method with F-SnO2 coated glass as substrate. From scanning electron microscopy analysis, the synthesized TiO2 thin film was found to be in nanometer-scale rod structure with a thickness of 4 µm. The Seebeck coefficient was measured in the temperature range of 300 – 400 K. The Seebeck coefficient is found to be in negative value which shows that synthesized film is an n-type semiconductor material, and is lower than the value of bulk-size material. This reduction in Seebeck coefficient of TiO2 thin film is likely due to the low dimensional effect and the difference of carrier concentration.

Organic-inorganic hybrid thin film solar cells using conducting polymer and gold nanoparticles

Science.gov (United States)

Hwan Jung, Hyung; Ho Kim, Dong; Su Kim, Chang; Bae, Tae-Sung; Bum Chung, Kwun; Yoon Ryu, Seung

2013-05-01

We employed poly(styrenesulfonate)-doped poly (3,4-ethylenedioxythiophene) (PEDOT:PSS) as a p-layer on textured fluorine-tin-oxide (FTO) glass in pin-type hydrogenated amorphous silicon solar cells (a-Si:H SCs). An amorphous tungsten oxide (WO3) layer and gold nanoparticles (Au-NPs) 10 nm in size were included to prevent the degradation and to increase short-circuit current by the Plasmon effect, respectively, between the PEDOT:PSS and intrinsic-Si layer. The energy band between PEDOT:PSS and WO3 was meaningfully adjusted by Au-NPs. The p-type PEDOT:PSS layer in these organic-inorganic hybrid a-Si:H SCs results in an increased conversion efficiency from ˜2.42% to ˜5.49% and an increased open-circuit voltage from ˜0.29 V to ˜0.56 V. PEDOT:PSS on textured FTO glass is sufficiently showing that it can replace the p-type Si layer in pin-type a-Si:H SCs.

Genetic association of FTO/IRX region with obesity and overweight in the Polish population.

Directory of Open Access Journals (Sweden)

Marta Sobalska-Kwapis

Full Text Available Genome-wide association studies (GWAS have identified many loci associated with body mass index (BMI in many different populations. Variants in the FTO locus are reported to be one of the strongest genetic predictors of obesity. Recent publications pointed also to a topologically associated domain (TAD which is identified as a novel region affecting BMI. The TAD area encompasses the IRXB cluster (IRX3, IRX5, IRX6, FTO and RPGRIP1L genes.In this study, we investigated the relationship between variation of the FTO and IRX genes and obesity in Poles. We presented a case-control association analysis (normal versus overweight and/or obesity group of Polish adult individuals (N = 5418. We determined whether or not the chromosomal region 16:53 500 000-55 500 000 contains polymorphic variants which are correlated with BMI in Polish population, including sex and age stratified analysis.The obtained results showed that the problem of weight-height abnormalities differently affects populations of Polish women and men (χ2 = 187.1; p0.98, r2>0.80. We confirmed presence of the genetic susceptibility loci located in intron 1 of the FTO gene, which were correlated with BMI in our study group. For the first time, our analyses revealed strong association of FTO intronic variants (block 8 with overweight in group of men only. We have also identified association of the IRX region with overweight and/or obesity in Polish individuals.Our study demonstrated how tested SNPs make differential contributions to obesity and overweight risk. We revealed sex dependent differences in the distribution of tested loci which are associated with BMI in the population of Poles.

Moessbauer effect and infrared study of some borate glass containing Mn and Fe oxides

International Nuclear Information System (INIS)

Gabr, M.

2005-01-01

Lithium borate glasses containing transition metals appeared now of very high technological and scientific interest. Therefore some lithium borate glasses containing mixed transition metal ions (manganese and iron) were investigated. The glass batches were melted at 1250 degree C for three hours and annealed at 350 degree C -over night- to obtain strain free glasses. Moessbauer Effect spectroscopy and Infrared analysis were employed to investigate the structural changes due to the change of their batches composition. Differential thermal analysis, magnetic susceptibility, density and molar volume measurements were also performed to study the effect of changing both manganese and iron oxides at the expense of boron oxide on these properties. Infrared analysis indicated the presence of different structural groups such as BO 3 , BO 4 , FeO 4 and MnO 6 as well as different vibrations indicated the presence of various bonds in the glass network. The values of the characteristic temperatures (T g , T c and T m ) showed gradual increase except those of the last sample where they showed a decrease. The mid sample showed the lowest stability value. It was found that the molar volume showed its highest value at R=0.33 [where R is the ratio of glass network modifier to the glass network former]. After that it showed gradual linear decrease. The magnetic susceptibility measurements showed approximately stable value between R=0.29 and 0.33, then it increased up to R=0.38, and after that, it decreased up to R= 0.43. The obtained magnetic susceptibility values indicated that all these glasses are paramagnetic. The obtained Moessbauer spectra and the calculated parameters confirmed that iron ions participated in the glass network as network former cations. It confirmed also that all glasses reflect paramagnetic character. The observed structural change were explained and correlated with the change of the measured physical properties

Commercial alkaline earth boroaluminosilicate glasses for sealing solid oxide cell stacks. Part I: Development of glass-ceramic microstructure and thermomechanical properties

DEFF Research Database (Denmark)

Agersted, Karsten; Balic-Zunic, Tonci

2018-01-01

Sealing performance in solid oxide cell (SOC) stacks and the devitrification process of commercially available alkaline earth boroaluminosilicate glasses containing 48‐61 mol% SiO2, 18‐28 mol% CaO, 1‐7 mol% MgO, 7‐10 mol% Al2O3, 1‐11 mol% B2O3 plus minor amounts of Na2O, K2O, FeO, and TiO2 were...... investigated and quantified through analysis of phase assemblages as function of heat treatments above the glass transition temperatures using the electron microprobe and powder X‐ray diffraction. For two of these glasses devitrification behavior was compared to the devitrification behavior of similar glasses...... produced in the laboratory. Glasses were characterized after annealing in air at 800°C and 850°C for up to 6 weeks. Even though the glasses lie within a relatively narrow compositional range, sealing performance and the resulting microstructures differed significantly. Best thermomechanical properties...

A Revised Method For Estimating Oxide Basicity Per The Smith Scale With Example Application To Glass Durability

International Nuclear Information System (INIS)

Reynolds, J.G.

2011-01-01

Previous researchers have developed correlations between oxide electronegativity and oxide basicity. The present paper revises those correlations using a newer method of calculating electronegativity of the oxygen anion. Basicity is expressed using the Smith α parameter scale. A linear relation was found between the oxide electronegativity and the Smith α parameter, with an R 2 of 0.92. An example application of this new correlation to the durability of high-level nuclear waste glass is demonstrated. The durability of waste glass was found to be directly proportional to the quantity and basicity of the oxides of tetrahedrally coordinated network forming ions.

TiO{sub 2} films obtained by microwave-activated chemical-bath deposition used to improve TiO{sub 2}-conducting glass contact

Energy Technology Data Exchange (ETDEWEB)

Zumeta, I.; Gonzalez, B. [Institute for Material Science and Technology, University of Havana, Colina Universitaria, Ciudad Habana 10 400 (Cuba); Ayllon, J.A.; Domenech, X. [Chemistry Department, Autonomous University of Barcelona, 08290 Cerdanyola del Valles (Spain); Vigil, E. [Institute for Material Science and Technology, University of Havana, Colina Universitaria, Ciudad Habana 10 400 (Cuba); Physics Faculty, University of Havana, Colina Universitaria, Ciudad Habana 10 400 (Cuba)

2009-10-15

In traditional solar cells, metal-semiconductor contacts used to extract photogenerated carriers are very important. In dye-sensitized solar cells (DSSC) not much attention has been given to contact between the TiO{sub 2} and the transparent conducting glass (TCO), which is used instead of a metal contact to extract electrons. TiO{sub 2} layers obtained by microwave-activated chemical-bath deposition (MW-CBD) are proposed to improve TiO{sub 2} contact to conducting glass. Spectra of incident photon to current conversion efficiency (IPCE) are obtained for two-photoelectrode TiO{sub 2} photoelectrochemical cells. IPCE spectra show higher values when TiO{sub 2} double layer photoelectrodes are used. In these, the first layer or contacting layer is made by MW-CBD. Best results are obtained for double layer photoelectrodes on FTO (SnO{sub 2}:F) as conducting oxide substrate. Modeling of IPCE spectra reveals the importance of electrical contact and electron extraction rate at the TiO{sub 2}/TCO interface. (author)

A High Optical Transmittance and Low Cost Touch Screen without Patterning

Directory of Open Access Journals (Sweden)

SAMADZAMINI, K.

2017-02-01

Full Text Available Transparent Conducting Oxide (TCO materials such as Fluorine Tin Oxide (FTO and Indium Tin Oxide (ITO due to their optical and electrical properties are used in touch screens as electrodes and wires. This paper proposes a novel technique of using Electrical Resistivity Tomography (ERT method in order to produce touch screens without pattering. Unlike existing techniques, the proposed methodology employs a uniform TCO coated screen with a maximum optical transmittance to convert the touch point coordinates into side electrodes voltages. The performance of the proposed method is tested experimentally on a FTO coated glass with a sheet resistance of 20 ohms/sq. The proposed methodology is found to be less complicated and low cost, since no pattern or electrodes are implemented in the display area.

Compact hematite buffer layer as a promoter of nanorod photoanode performances

Science.gov (United States)

Milan, R.; Cattarin, S.; Comisso, N.; Baratto, C.; Kaunisto, K.; Tkachenko, N. V.; Concina, I.

2016-10-01

The effect of a thin α-Fe2O3 compact buffer layer (BL) on the photoelectrochemical performances of a bare α-Fe2O3 nanorods photoanode is investigated. The BL is prepared through a simple spray deposition onto a fluorine-doped tin oxide (FTO) conducting glass substrate before the growth of a α-Fe2O3 nanorods via a hydrothermal process. Insertion of the hematite BL between the FTO and the nanorods markedly enhances the generated photocurrent, by limiting undesired losses of photogenerated charges at the FTO||electrolyte interface. The proposed approach warrants a marked improvement of material performances, with no additional thermal treatment and no use/dispersion of rare or toxic species, in agreement with the principles of green chemistry.

Morphology dependent dye-sensitized solar cell properties of nanocrystalline zinc oxide thin films

Energy Technology Data Exchange (ETDEWEB)

Sharma, S.K., E-mail: sanjeevlrs732000@yahoo.co.in [Department of Information and Communication, Cheju Halla College, Jeju City 690 708 (Korea, Republic of); Inamdar, A.I.; Im, Hyunsik [Department of Semiconductor Science, Dongguk University, Seoul 100 715 (Korea, Republic of); Kim, B.G. [Department of Information and Communication, Cheju Halla College, Jeju City 690 708 (Korea, Republic of); Patil, P.S. [Thin Film Materials Laboratory, Department of Physics, Shivaji University, Kolhapur 416 004 (India)

2011-02-03

Research highlights: > Nano-crystalline zinc oxide thin films were electrosynthesized from an aqueous zinc acetate [Zn(CH{sub 3}COO){sub 2}.2H{sub 2}O] solution onto FTO coated conducting glass substrates using two different electrochemical routes, namely (i) without an organic surfactant and (ii) with an organic surfactant, viz. PVA (poly-vinyl alcohol) or SDS (sodium dodecyl sulfate). > The reproducibility of the catalytic activity of the SDS and PVA surfactants in the modification of the morphologies was observed. > Vertically aligned nest-like and compact structures were observed from the SDS and PVA mediated films, respectively, while the grain size in the ZnO thin films without an organic surfactant was observed to be {approx}150 nm. > The dye sensitized ZnO electrodes displayed excellent properties in the conversion process from light to electricity. The efficiencies of the surfactant mediated nanocrystalline ZnO thin films, viz. ZnO:SDS and ZnO:PVA, sensitized with ruthenium-II (N3) dye were observed to be 0.49% and 0.27%, respectively. - Abstract: Nano-crystalline zinc oxide thin films were electrosynthesized with an aqueous zinc acetate [Zn(CH{sub 3}COO){sub 2}.2H{sub 2}O] solution on to FTO coated glass substrates. Two different electrochemical baths were used, namely (i) without an organic surfactant and (ii) with an organic surfactant, viz. PVA (poly-vinyl alcohol) and SDS (sodium dodecyl sulfate). The organic surfactants played an important role in modifying the surface morphology, which influenced the size of the crystallites and dye-sensitized solar cell (DSSC) properties. The vertically aligned thin and compact hexagonal crystallites were observed with SDS mediated films, while the grain size in the films without an organic surfactant was observed to be {approx}150 nm. The conversion efficiencies of the ZnO:SDS:Dye and ZnO:PVA:Dye thin films were observed to be 0.49% and 0.27%, respectively.

The effect on phase separation of the oxidation state of molybdenum in a Na2O-B2O3-SiO2 glass

International Nuclear Information System (INIS)

Kawamoto, Y.; Clemens, K.; Tomozawa, M.; Warden, J.T.

1981-01-01

The effect of oxidation state on phase separation was studied for 13Na 2 O, 49B 2 O 3 , 38SiO 2 (mol%) glasses containing 1 mol% Mo oxide. The glasses were melted under various conditions to vary the oxidation states of Mo ions. The oxidation states of Mo ions were determined by chemical analysis and ESR. The crystallisation tendency, the immiscibility temperature, and the phase separation morphology of the glasses were examined by DTA, x-ray diffraction, opalescence method, and replica electron microscopy. Glasses containing Mo 4+ ions have a great tendency to precipitate MoO 2 crystals. The immiscibility temperature of glass goes through a minimum when the oxidation states of Mo ions are changed. It was suggested that there is an optimum oxidation state to prevent crystallisation and to suppress the phase separation tendency of this system. (author)

Large-area SnO2: F thin films by offline APCVD

International Nuclear Information System (INIS)

Wang, Yan; Wu, Yucheng; Qin, Yongqiang; Zhang, Zhihai; Shi, Chengwu; Zhang, Qingfeng; Li, Changhao; Xia, Xiaohong; Sun, Stanley; Chen, Leon

2011-01-01

Highlights: → Large-area (1245 mm x 635 mm) FTO thin films were successfully deposited by offline APCVD process. → The as-prepared FTO thin films with sheet resistance 8-11 Ω/□ and direct transmittance more than 83% exhibited better than that of the online ones. → The maximum quantum efficiency of the solar cells based on offline FTO substrate was 0.750 at wavelength 540 nm. → The power of the solar modules using the offline FTO as glass substrates was 51.639 W, higher than that of the modules based on the online ones. -- Abstract: In this paper, we reported the successful preparation of fluorine-doped tin oxide (FTO) thin films on large-area glass substrates (1245 mm x 635 mm x 3 mm) by self-designed offline atmospheric pressure chemical vapor deposition (APCVD) process. The FTO thin films were achieved through a combinatorial chemistry approach using tin tetrachloride, water and oxygen as precursors and Freon (F-152, C2H4F2) as dopant. The deposited films were characterized for crystallinity, morphology (roughness) and sheet resistance to aid optimization of materials suitable for solar cells. We got the FTO thin films with sheet resistance 8-11 Ω/□ and direct transmittance more than 83%. X-ray diffraction (XRD) characterization suggested that the as-prepared FTO films were composed of multicrystal, with the average crystal size 200-300 nm and good crystallinity. Further more, the field emission scanning electron microscope (FESEM) images showed that the films were produced with good surface morphology (haze). Selected samples were used for manufacturing tandem amorphous silicon (a-Si:H) thin film solar cells and modules by plasma enhanced chemical vapor deposition (PECVD). Compared with commercially available FTO thin films coated by online chemical vapor deposition, our FTO coatings show excellent performance resulting in a high quantum efficiency yield for a-Si:H solar cells and ideal open voltage and short circuit current for a-Si:H solar

Compositional Dependence of Solubility/Retention of Molybdenum Oxides in Aluminoborosilicate-Based Model Nuclear Waste Glasses.

Science.gov (United States)

Brehault, Antoine; Patil, Deepak; Kamat, Hrishikesh; Youngman, Randall E; Thirion, Lynn M; Mauro, John C; Corkhill, Claire L; McCloy, John S; Goel, Ashutosh

2018-02-08

Molybdenum oxides are an integral component of the high-level waste streams being generated from the nuclear reactors in several countries. Although borosilicate glass has been chosen as the baseline waste form by most of the countries to immobilize these waste streams, molybdate oxyanions (MoO 4 2- ) exhibit very low solubility (∼1 mol %) in these glass matrices. In the past three to four decades, several studies describing the compositional and structural dependence of molybdate anions in borosilicate and aluminoborosilicate glasses have been reported in the literature, providing a basis for our understanding of fundamental science that governs the solubility and retention of these species in the nuclear waste glasses. However, there are still several open questions that need to be answered to gain an in-depth understanding of the mechanisms that control the solubility and retention of these oxyanions in glassy waste forms. This article is focused on finding answers to two such questions: (1) What are the solubility and retention limits of MoO 3 in aluminoborosilicate glasses as a function of chemical composition? (2) Why is there a considerable increase in the solubility of MoO 3 with incorporation of rare-earth oxides (for example, Nd 2 O 3 ) in aluminoborosilicate glasses? Accordingly, three different series of aluminoborosilicate glasses (compositional complexity being added in a tiered approach) with varying MoO 3 concentrations have been synthesized and characterized for their ability to accommodate molybdate ions in their structure (solubility) and as a glass-ceramic (retention). The contradictory viewpoints (between different research groups) pertaining to the impact of rare-earth cations on the structure of aluminoborosilicate glasses are discussed, and their implications on the solubility of MoO 3 in these glasses are evaluated. A novel hypothesis explaining the mechanism governing the solubility of MoO 3 in rare-earth containing aluminoborosilicate

Gender-Dependent Association of FTO Polymorphisms with Body Mass Index in Mexicans.

Directory of Open Access Journals (Sweden)

Yolanda Saldaña-Alvarez

Full Text Available To evaluate the associations between six single-nucleotide polymorphisms (SNPs in intron 1 of FTO and body mass index (BMI, a case-control association study of 2314 unrelated Mexican-Mestizo adult subjects was performed. The association between each SNP and BMI was tested using logistic and linear regression adjusted for age, gender, and ancestry and assuming additive, recessive, and dominant effects of the minor allele. Association analysis after BMI stratification showed that all five FTO SNPs (rs1121980, rs17817449, rs3751812, rs9930506, and rs17817449, were significantly associated with obesity class II/III under an additive model (P<0.05. Interestingly, we also documented a genetic model-dependent influence of gender on the effect of FTO variants on increased BMI. Two SNPs were specifically associated in males under a dominant model, while the remainder were associated with females under additive and recessive models (P<0.05. The SNP rs9930506 showed the highest increased in obesity risk in females (odds ratio = 4.4. Linear regression using BMI as a continuous trait also revealed differential FTO SNP contributions. Homozygous individuals for the risk alleles of rs17817449, rs3751812, and rs9930506 were on average 2.18 kg/m(2 heavier than homozygous for the wild-type alleles; rs1121980 and rs8044769 showed significant but less-strong effects on BMI (1.54 kg/m(2 and 0.9 kg/m(2, respectively. Remarkably, rs9930506 also exhibited positive interactions with age and BMI in a gender-dependent manner. Women carrying the minor allele of this variant have a significant increase in BMI by year (0.42 kg/m(2, P = 1.17 x 10(-10. Linear regression haplotype analysis under an additive model, confirmed that the TGTGC haplotype harboring all five minor alleles, increased the BMI of carriers by 2.36 kg/m(2 (P = 1.15 x 10(-5. Our data suggest that FTO SNPs make differential contributions to obesity risk and support the hypothesis that gender differences in the

Gender-Dependent Association of FTO Polymorphisms with Body Mass Index in Mexicans

Science.gov (United States)

Saldaña-Alvarez, Yolanda; Salas-Martínez, María Guadalupe; García-Ortiz, Humberto; Luckie-Duque, Angélica; García-Cárdenas, Gustavo; Vicenteño-Ayala, Hermenegildo; Cordova, Emilio J.; Esparza-Aguilar, Marcelino; Contreras-Cubas, Cecilia; Carnevale, Alessandra; Chávez-Saldaña, Margarita; Orozco, Lorena

2016-01-01

To evaluate the associations between six single-nucleotide polymorphisms (SNPs) in intron 1 of FTO and body mass index (BMI), a case-control association study of 2314 unrelated Mexican-Mestizo adult subjects was performed. The association between each SNP and BMI was tested using logistic and linear regression adjusted for age, gender, and ancestry and assuming additive, recessive, and dominant effects of the minor allele. Association analysis after BMI stratification showed that all five FTO SNPs (rs1121980, rs17817449, rs3751812, rs9930506, and rs17817449), were significantly associated with obesity class II/III under an additive model (P<0.05). Interestingly, we also documented a genetic model-dependent influence of gender on the effect of FTO variants on increased BMI. Two SNPs were specifically associated in males under a dominant model, while the remainder were associated with females under additive and recessive models (P<0.05). The SNP rs9930506 showed the highest increased in obesity risk in females (odds ratio = 4.4). Linear regression using BMI as a continuous trait also revealed differential FTO SNP contributions. Homozygous individuals for the risk alleles of rs17817449, rs3751812, and rs9930506 were on average 2.18 kg/m2 heavier than homozygous for the wild-type alleles; rs1121980 and rs8044769 showed significant but less-strong effects on BMI (1.54 kg/m2 and 0.9 kg/m2, respectively). Remarkably, rs9930506 also exhibited positive interactions with age and BMI in a gender-dependent manner. Women carrying the minor allele of this variant have a significant increase in BMI by year (0.42 kg/m2, P = 1.17 x 10−10). Linear regression haplotype analysis under an additive model, confirmed that the TGTGC haplotype harboring all five minor alleles, increased the BMI of carriers by 2.36 kg/m2 (P = 1.15 x 10−5). Our data suggest that FTO SNPs make differential contributions to obesity risk and support the hypothesis that gender differences in the mechanisms

A Comparative Study of Natural Fiber and Glass Fiber Fabrics Properties with Metal or Oxide Coatings

International Nuclear Information System (INIS)

Lusis, Andrej; Pentjuss, Evalds; Bajars, Gunars; Sidorovicha, Uljana; Strazds, Guntis

2015-01-01

Rapidly growing global demand for technical textiles industries is stimulated to develop new materials based on hybrid materials (yarns, fabrics) made from natural and glass fibres. The influence of moisture on the electrical properties of metal and metal oxide coated bast (flax, hemp) fibre and glass fibre fabrics are studied by electrical impedance spectroscopy and thermogravimetry. The bast fibre and glass fiber fabrics are characterized with electrical sheet resistance. The method for description of electrical sheet resistance of the metal and metal oxide coated technical textile is discussed. The method can be used by designers to estimate the influence of moisture on technical data of new metal coated hybrid technical textile materials and products

New roots to formation of nanostructures on glass surface through anodic oxidation of sputtered aluminum

Directory of Open Access Journals (Sweden)

Satoru Inoue, Song-Zhu Chu, Kenji Wada, Di Li and Hajime Haneda

2003-01-01

Full Text Available New processes for the preparation of nanostructure on glass surfaces have been developed through anodic oxidation of sputtered aluminum. Aluminum thin film sputtered on a tin doped indium oxide (ITO thin film on a glass surface was converted into alumina by anodic oxidation. The anodic alumina gave nanometer size pore array standing vertically on the glass surface. Kinds of acids used in the anodic oxidation changed the pore size drastically. The employment of phosphoric acid solution gave several tens nanometer size pores. Oxalic acid cases produced a few tens nanometer size pores and sulfuric acid solution provided a few nanometer size pores. The number of pores in a unit area could be changed with varying the applied voltage in the anodization and the pore sizes could be increased by phosphoric acid etching. The specimen consisting of a glass substrate with the alumina nanostructures on the surface could transmit UV and visible light. An etched specimen was dipped in a TiO2 sol solution, resulting in the impregnation of TiO2 sol into the pores of alumina layer. The TiO2 sol was heated at ~400 °C for 2 h, converting into anatase phase TiO2. The specimens possessing TiO2 film on the pore wall were transparent to the light in UV–Visible region. The electro deposition technique was applied to the introduction of Ni metal into pores, giving Ni nanorod array on the glass surface. The removal of the barrier layer alumina at the bottom of the pores was necessary to attain smooth electro deposition of Ni. The photo catalytic function of the specimens possessing TiO2 nanotube array was investigated in the decomposition of acetaldehyde gas under the irradiation of UV light, showing that the rate of the decomposition was quite large.

Dietary Intake, FTO Genetic Variants, and Adiposity : A Combined Analysis of Over 16,000 Children and Adolescents

NARCIS (Netherlands)

Qi, Qibin; Downer, Mary K.; Kilpelaeinen, Tuomas O.; Taal, H. Rob; Barton, Sheila J.; Ntalla, Ioanna; Standl, Marie; Boraska, Vesna; Huikari, Ville; Kiefte-de Jong, Jessica C.; Koerner, Antje; Lakka, Timo A.; Liu, Gaifen; Magnusson, Jessica; Okuda, Masayuki; Raitakari, Olli; Richmond, Rebecca; Scott, Robert A.; Bailey, Mark E. S.; Scheuermann, Kathrin; Holloway, John W.; Inskip, Hazel; Isasi, Carmen R.; Mossavar-Rahmani, Yasmin; Jaddoe, Vincent W. V.; Laitinen, Jaana; Lindi, Virpi; Melen, Erik; Pitsiladis, Yannis; Pitkaenen, Niina; Snieder, Harold; Heinrich, Joachim; Timpson, Nicholas J.; Wang, Tao; Yuji, Hinoda; Zeggini, Eleftheria; Dedoussis, George V.; Kaplan, Robert C.; Wylie-Rosett, Judith; Loos, Ruth J. F.; Hu, Frank B.; Qi, Lu

The FTO gene harbors variation with the strongest effect on adiposity and obesity risk. Previous data support a role for FTO variation in influencing food intake. We conducted a combined analysis of 16,094 boys and girls aged 1-18 years from 14 studies to examine the following: 1) the association

FTO Is Associated with Aortic Valve Stenosis in a Gender Specific Manner of Heterozygote Advantage: A Population-Based Case-Control Study.

Directory of Open Access Journals (Sweden)

Cindy Thron

Full Text Available Single nucleotide polymorphisms (SNPs within the Fat mass and obesity associated (FTO gene have been linked with increased body weight. However, the data on an association of FTO with cardiovascular diseases remains conflicting. Therefore, we ascertained whether FTO is associated with aortic valve stenosis (AVS, one of the most frequent cardiovascular diseases in the Western world.In this population-based case-control study the FTO SNP rs9939609 was analyzed in 300 German patients with AVS and 429 German controls of the KORA survey S4, representing a random population. Blood samples were collected prior to aortic valve replacement in AVS cases and FTO rs9939609 was genotyped via ARMS-PCR. Genotype frequencies differed significantly between AVS cases and KORA controls (p = 0.004. Separate gender-analyses uncovered an association of FTO with AVS exclusively in males; homozygote carriers for the risk-allele (A had a higher risk to develop AVS (p = 0.017, odds ratio (OR 1.727; 95% confidence interval (CI 1.087-2.747, recessive model, whereas heterozygote carriers for the risk-allele showed a lower risk (p = 0.002, OR 0.565, 95% CI 0.384-0.828, overdominant model. After adjustment for multiple co-variables, the odds ratios of heterozygotes remained significant for an association with AVS (p = 0.008, OR 0.565, 95% CI 0.369-0.861.This study revealed an association of FTO rs9939609 with AVS. Furthermore, this association was restricted to men, with heterozygotes having a significantly lower chance to develop AVS. Lastly, the association between FTO and AVS was independent of BMI and other variables such as diabetes mellitus.

FTO Is Associated with Aortic Valve Stenosis in a Gender Specific Manner of Heterozygote Advantage: A Population-Based Case-Control Study.

Science.gov (United States)

Thron, Cindy; Akhyari, Payam; Godehardt, Erhard; Lichtenberg, Artur; Rüther, Ulrich; Seehaus, Stefanie

2015-01-01

Single nucleotide polymorphisms (SNPs) within the Fat mass and obesity associated (FTO) gene have been linked with increased body weight. However, the data on an association of FTO with cardiovascular diseases remains conflicting. Therefore, we ascertained whether FTO is associated with aortic valve stenosis (AVS), one of the most frequent cardiovascular diseases in the Western world. In this population-based case-control study the FTO SNP rs9939609 was analyzed in 300 German patients with AVS and 429 German controls of the KORA survey S4, representing a random population. Blood samples were collected prior to aortic valve replacement in AVS cases and FTO rs9939609 was genotyped via ARMS-PCR. Genotype frequencies differed significantly between AVS cases and KORA controls (p = 0.004). Separate gender-analyses uncovered an association of FTO with AVS exclusively in males; homozygote carriers for the risk-allele (A) had a higher risk to develop AVS (p = 0.017, odds ratio (OR) 1.727; 95% confidence interval (CI) 1.087-2.747, recessive model), whereas heterozygote carriers for the risk-allele showed a lower risk (p = 0.002, OR 0.565, 95% CI 0.384-0.828, overdominant model). After adjustment for multiple co-variables, the odds ratios of heterozygotes remained significant for an association with AVS (p = 0.008, OR 0.565, 95% CI 0.369-0.861). This study revealed an association of FTO rs9939609 with AVS. Furthermore, this association was restricted to men, with heterozygotes having a significantly lower chance to develop AVS. Lastly, the association between FTO and AVS was independent of BMI and other variables such as diabetes mellitus.

Association of genetic variation in FTO with risk of obesity and type 2 diabetes with data from 96,551 East and South Asians

DEFF Research Database (Denmark)

Li, H; Oskari Kilpeläinen, Tuomas; Liu, C

2012-01-01

FTO harbours the strongest known obesity-susceptibility locus in Europeans. While there is growing evidence for a role for FTO in obesity risk in Asians, its association with type 2 diabetes, independently of BMI, remains inconsistent. To test whether there is an association of the FTO locus...

X-ray photoemission spectroscopy (XPS) study of uranium, neptunium and plutonium oxides in silicate-based glasses

International Nuclear Information System (INIS)

Lam, D.J.; Veal, B.W.; Paulikas, A.P.

1982-11-01

Using XPS as the principal investigative tool, we are in the process of examining the bonding properties of selected metal oxides added to silicate glass. In this paper, we present results of XPS studies of uranium, neptunium, and plutonium in binary and multicomponent silicate-based glasses. Models are proposed to account for the very diverse bonding properties of 6+ and 4+ actinide ions in the glasses

Role of groundwater oxidation potential and radiolysis on waste glass performance in crystalline repository environments

International Nuclear Information System (INIS)

Jantzen, C.M.; Bibler, N.E.

1986-01-01

Laboratory experiments have shown that groundwater conditions in a granite repository will be as reducing as those in a basalt repository. Chemical analysis of the reduced groundwaters confirmed that the Fe 2+ /Fe 3+ couple controls the oxidation potential (Eh). The reducing groundwater conditions were found to decrease the time-dependent release of soluble elements (Li and B) from the waste glass. However, due to the lower solubility of multivalent elements released from the glass when the groundwaters are reducing, these elements have significantly lower concentrations in the leachates. Gamma radiolysis reduced the oxidation potential of both granitic and basaltic groundwater in the absence of both waste glass and oxygen. This occurred in tests at atmospheric pressure where H 2 could have escaped from the solution. The mechanism for this decrease in Eh is under investigation but appears related to the reactive amorphous precipitate in both groundwaters. The results of these tests suggest that radiolysis may not cause the groundwaters to become oxidizing in a crystalline repository when abundant Fe 2+ species are present

Experimental and theoretical approach on the optical properties of zinc borotellurite glass doped with dysprosium oxide

Science.gov (United States)

Halimah, M. K.; Ami Hazlin, M. N.; Muhammad, F. D.

2018-04-01

A series of glass samples with chemical formula {[(TeO2)0.7(B2O3)0.3]0.7(ZnO)0.3}1 - x(Dy2O3)x where x = 0.01, 0.02, 0.03, 0.04 and 0.05 M fraction were synthesized through conventional melt-quenching method. The most common way to fabricate a glass material is by fusion of two or more component oxides followed by their quenching. This technique is known as melt-quenching technique. Kaur et al. (2016) [1] highlighted that the melt-quenching method able to enhance the mechanical properties like hardness and flexural strength of the material. The nature of the glass systems is proven to be amorphous based on the XRD pattern. The FTIR spectra of the glass systems confirm the existence of five bands which are assigned for the BO4, BO3, TeO4 and TeO3 vibrational groups. The density of the glass systems is increased with the addition of Dy2O3 while the molar volume is found to be inversely proportional to the density of the proposed glass. The optical properties of the glasses are determined through the absorption spectra obtained from the UV-VIS spectrophotometer. From the absorption spectra, the indirect and direct optical band gaps and the Urbach energy are found to be inversely proportional to each other. As the molar fraction of the Dy2O3 increased, the optical band gaps are observed to increase as opposed to the Urbach energy. For this glass system, the values of refractive index, electronic polarizability, oxide ion polarizability and the optical basicity are found to decrease as the addition of the dysprosium oxide is increased. From the emission spectra, two intense blue and yellow emission bands are observed, which correspond to the 4F9/2 → 6H15/2 and 4F9/2 → 6H13/2 transitions of Dy3 + ions respectively. The CIE chromaticity coordinates of the zinc borotellurite glass systems are found to be located in the white light region. Generation of white light The generation of the white light can be achieved by using two emission bands which comprise of the yellow

Solution-processed all-oxide bulk heterojunction solar cells based on CuO nanaorod array and TiO2 nanocrystals

Science.gov (United States)

Wu, Fan; Qiao, Qiquan; Bahrami, Behzad; Chen, Ke; Pathak, Rajesh; Tong, Yanhua; Li, Xiaoyi; Zhang, Tiansheng; Jian, Ronghua

2018-05-01

We present a method to synthesize CuO nanorod array/TiO2 nanocrystals bulk heterojunction (BHJ) on fluorine-tin-oxide (FTO) glass, in which single-crystalline p-type semiconductor of the CuO nanorod array is grown on the FTO glass by hydrothermal reaction and the n-type semiconductor of the TiO2 precursor is filled into the CuO nanorods to form well-organized nano-interpenetrating BHJ after air annealing. The interface charge transfer in CuO nanorod array/TiO2 heterojunction is studied by Kelvin probe force microscopy (KPFM). KPFM results demonstrate that the CuO nanorod array/TiO2 heterojunction can realize the transfer of photo-generated electrons from the CuO nanorod array to TiO2. In this work, a solar cell with the structure FTO/CuO nanoarray/TiO2/Al is successfully fabricated, which exhibits an open-circuit voltage (V oc) of 0.20 V and short-circuit current density (J sc) of 0.026 mA cm‑2 under AM 1.5 illumination. KPFM studies indicate that the very low performance is caused by an undesirable interface charge transfer. The interfacial surface potential (SP) shows that the electron concentration in the CuO nanorod array changes considerably after illumination due to increased photo-generated electrons, but the change in the electron concentration in TiO2 is much less than in CuO, which indicates that the injection efficiency of the photo-generated electrons from CuO to TiO2 is not satisfactory, resulting in an undesirable J sc in the solar cell. The interface photovoltage from the KPFM measurement shows that the low V oc results from the small interfacial SP difference between CuO and TiO2 because the low injected electron concentration cannot raise the Fermi level significantly in TiO2. This conclusion agrees with the measured work function results under illumination. Hence, improvement of the interfacial electron injection is primary for the CuO nanorod array/TiO2 heterojunction solar cells.

Phenome Wide Association Studies demonstrating pleiotropy of genetic variants within FTO with and without adjustment for body mass index

Directory of Open Access Journals (Sweden)

Robert Michael Cronin

2014-08-01

Full Text Available Phenome-wide association studies (PheWAS have demonstrated utility in validating genetic associations derived from traditional genetic studies as well as identifying novel genetic associations. Here we used an electronic health record (EHR-based PheWAS to explore pleiotropy of genetic variants in the fat mass and obesity associated gene (FTO, some of which have been previously associated with obesity and type 2 diabetes (T2D. We used a population of 10,487 individuals of European ancestry with genome-wide genotyping from the Electronic Medical Records and Genomics (eMERGE Network and another population of 13,711 individuals of European ancestry from the BioVU DNA biobank at Vanderbilt genotyped using Illumina HumanExome BeadChip. A meta-analysis of the two study populations replicated the well-described associations between FTO variants and obesity (odds ratio [OR]=1.25, 95% Confidence Interval=1.11-1.24, p=2.10 x 10 9 and FTO variants and T2D (OR=1.14, 95% CI=1.08-1.21, p=2.34 x 10 6. The meta-analysis also demonstrated that FTO variant rs8050136 was significantly associated with sleep apnea (OR=1.14, 95% CI=1.07-1.22, p=3.33 x 10 5; however, the association was attenuated after adjustment for body mass index (BMI. Novel phenotype associations with obesity-associated FTO variants included fibrocystic breast disease (rs9941349, OR=0.81, 95% CI=0.74-0.91, p=5.41x10 5 and trends toward associations with nonalcoholic liver disease and gram-positive bacterial infections. FTO variants not associated with obesity demonstrated other potential disease associations including noninflammatory disorders of the cervix and chronic periodontitis. These results suggest that genetic variants in FTO may have pleiotropic associations, some of which are not mediated by obesity.

Photoelectrochemical Properties of FeO Supported on TiO2-Based Thin Films Converted from Self-Assembled Hydrogen Titanate Nanotube Powders

Directory of Open Access Journals (Sweden)

Kyung-Jong Noh

2012-01-01

Full Text Available A photoanode was fabricated using hematite (α-Fe2O3 nanoparticles which had been held in a thin film of hydrogen titanate nanotubes (H-TiNT, synthesized by repetitive self-assembling method on FTO (fluorine-doped tin oxide glass, which were incorporated via dipping process in aqueous Fe(NO33 solution. Current voltage (I-V electrochemical properties of the photoanode heat-treated at 500°C for 10 min in air were evaluated under ultraviolet-visible light irradiation. Microstructure and crystallinity changes were also investigated. The prepared Fe2O3/H-TiNT/FTO composite thin film exhibited about threefold as much photocurrent as the Fe2O3/FTO film. The improvement in photocurrent was considered to be caused by reduced recombination of electrons and holes, with an appropriate amount of Fe2O3 spherical nanoparticles supported on the H-TiNT/FTO film. Nanosized spherical Fe2O3 particles with about 65 wt% on the H-TiNT/FTO film showed best performance in our study.

Associations of variants in FTO and near MC4R with obesity traits in South Asian Indians.

Science.gov (United States)

Vasan, Senthil K; Fall, Tove; Neville, Matthew J; Antonisamy, Belavendra; Fall, Caroline H; Geethanjali, Finney S; Gu, Harvest F; Raghupathy, Palany; Samuel, Prasanna; Thomas, Nihal; Brismar, Kerstin; Ingelsson, Erik; Karpe, Fredrik

2012-11-01

Recent genome-wide association studies show that loci in FTO and melanocortin 4 receptor (MC4R) associate with obesity-related traits. Outside Western populations the associations between these variants have not always been consistent and in Indians it has been suggested that FTO relates to diabetes without an obvious intermediary obesity phenotype. We investigated the association between genetic variants in FTO (rs9939609) and near MC4R (rs17782313) with obesity- and type 2 diabetes (T2DM)-related traits in a longitudinal birth cohort of 2,151 healthy individuals from the Vellore birth cohort in South India. The FTO locus displayed significant associations with several conventional obesity-related anthropometric traits. The per allele increase is about 1% for BMI, waist circumference (WC), hip circumference (HC), and waist-hip ratio. Consistent associations were observed for adipose tissue-specific measurements such as skinfold thickness reinforcing the association with obesity-related traits. Obesity associations for the MC4R locus were weak or nonsignificant but a signal for height (P work poorly in the Indian "thin-fat" phenotype.

FTO genotype, dietary protein, and change in appetite: the Preventing Overweight Using Novel Dietary Strategies trial.

Science.gov (United States)

Huang, Tao; Qi, Qibin; Li, Yanping; Hu, Frank B; Bray, George A; Sacks, Frank M; Williamson, Donald A; Qi, Lu

2014-05-01

A common obesity-risk variant rs9939609 in the fat mass- and obesity-associated (FTO) gene was recently shown to affect appetite, and the gene is sensitive to the regulation of amino acids. We examined the interaction between FTO genotype and protein intake on the long-term changes in appetite in a randomized controlled trial. We genotyped FTO rs9939609 in 737 overweight adults in the 2-y Preventing Overweight Using Novel Dietary Strategies trial and assessed 4 appetite-related traits including cravings, fullness, hunger, and prospective consumption. We showed that dietary protein significantly modified genetic effects on changes in food cravings and appetite scores at 6 mo after adjustment for age, sex, ethnicity, baseline body mass index, weight change, and baseline value for respective outcomes (P-interaction = 0.027 and 0.048, respectively). The A allele was associated with a greater decrease in food cravings and appetite scores in participants with high-protein-diet intake (P = 0.027 and 0.047, respectively) but not in subjects in the low-protein-diet group (P = 0.384 and 0.078, respectively). The weight regain from 6 to 24 mo attenuated gene-protein interactions. Protein intakes did not modify FTO genotype effects on other appetite measures. Our data suggest that individuals with the FTO rs9939609 A allele might obtain more benefits in a reduction of food cravings and appetite by choosing a hypocaloric and higher-protein weight-loss diet. This trial was registered at clinicaltrials.gov as NCT00072995.

Development of an oxidation resistant glass-ceramic composite coating on Ti-47Al-2Cr-2Nb alloy

Science.gov (United States)

Li, Wenbo; Zhu, Shenglong; Chen, Minghui; Wang, Cheng; Wang, Fuhui

2014-02-01

Three glass-ceramic composite coatings were prepared on Ti-47Al-2Cr-2Nb alloy by air spraying technique and subsequent firing. The aim of this work is to study the reactions between glass matrix and inclusions and their effects on the oxidation resistance of the glass-ceramic composite coating. The powders of alumina, quartz, or both were added into the aqueous solution of potassium silicate (ASPS) to form slurries used as the starting materials for the composite coatings. The coating formed from an ASPS-alumina slurry was porous, because the reaction between alumina and potassium silicate glass resulted in the formation of leucite (KAlSi2O6), consuming substantive glass phase and hindering the densification of the composite coating. Cracks were observed in the coating prepared from an ASPS-quartz slurry due to the larger volume shrinkage of the coating than that of the alloy. In contrast, an intact and dense SiO2-Al2O3-glass coating was successfully prepared from an ASPS-alumina-silica slurry. The oxidation behavior of the SiO2-Al2O3-glass composite coating on Ti-47Al-2Cr-2Nb alloy was studied at 900 °C. The SiO2-Al2O3-glass composite coating acted as an oxygen diffusion barrier, and prevented the inward diffusion of the oxygen from the air to the coating/alloy interface, therefore, decreasing the oxidation rate of the Ti-47Al-2Cr-2Nb alloy significantly.

FTO POLYMORPHISM AND PHYSICAL FITNESS IN OBESE SCHOOLCHILDREN AFTER AN INTERVENTION PROGRAM

Directory of Open Access Journals (Sweden)

Greice Graziela Moraes

Full Text Available ABSTRACT Introduction: Recent studies have shown that the association of FTO rs9939609 gene polymorphism with obesity depends on the level of the individual’s physical activity. However, there are some studies that evaluated physical fitness, health, and motor performance in relation to the rs9939609 FTO gene polymorphism. Objective: To evaluate how the rs9939609 FTO gene polymorphism affects the results of physical fitness tests related to health and athletic performance in schoolchildren after 4 months of intervention of physical exercise. Method: The rs9939609 FTO gene polymorphism was genotyped in a total of 36 schoolchildren from southern Brazil, aged 8 to 16 years. Body mass index (BMI, health-related physical fitness (cardiorespiratory fitness, abdominal strength/endurance, and flexibility and motor performance (upper and lower limb strength, agility, and speed were evaluated. The intervention included exercise strategies based on Physical Education, healthy eating, and oral and postural care. Results: In the experimental group, after the intervention, significant differences were noted in individuals with the TT genotype. These individuals showed improvements in abdominal strength (p=0.025, lower limb strength (p=0.037 and agility (p=0.021. For individuals with the AA/AT genotype, improvements in flexibility (p=0.026, abdominal strength (p=0.002, upper limb strength (p=0.008 and lower limb strength (p=0.001 were observed. However, these differences were not statistically significant when comparing the TT and AT/AA genotypes. Conclusions: The experimental group showed improvements in abdominal strength, lower limb strength, and speed. Yet, individuals with different genotypes (AA/AT and TT for polymorphism rs9939609 exhibited similar values for indicators of physical fitness, health, and motor performance. Level of Evidence II; Lesser quality RCT.

Calcium-borosilicate glass-ceramics wasteforms to immobilize rare-earth oxide wastes from pyro-processing

Energy Technology Data Exchange (ETDEWEB)

Kim, Miae [Department of Materials Science and Engineering and Division of Advanced Nuclear Engineering, Pohang University of Science and Technology (POSTECH), Pohang, Gyeongbuk, 790-784 (Korea, Republic of); Heo, Jong, E-mail: jheo@postech.ac.kr [Department of Materials Science and Engineering and Division of Advanced Nuclear Engineering, Pohang University of Science and Technology (POSTECH), Pohang, Gyeongbuk, 790-784 (Korea, Republic of); Department of Materials Engineering, Adama Science and Technology University (ASTU), PO Box 1888, Adama (Ethiopia)

2015-12-15

Glass-ceramics containing calcium neodymium(cerium) oxide silicate [Ca{sub 2}Nd{sub 8-x}Ce{sub x}(SiO{sub 4}){sub 6}O{sub 2}] crystals were fabricated for the immobilization of radioactive wastes that contain large portions of rare-earth ions. Controlled crystallization of alkali borosilicate glasses by heating at T ≥ 750 °C for 3 h formed hexagonal Ca–silicate crystals. Maximum lanthanide oxide waste loading was >26.8 wt.%. Ce and Nd ions were highly partitioned inside Ca–silicate crystals compared to the glass matrix; the rare-earth wastes are efficiently immobilized inside the crystalline phases. The concentrations of Ce and Nd ions released in a material characterization center-type 1 test were below the detection limit (0.1 ppb) of inductively coupled plasma mass spectroscopy. Normalized release values performed by a product consistency test were 2.64·10{sup −6} g m{sup −2} for Ce ion and 2.19·10{sup −6} g m{sup −2} for Nd ion. Results suggest that glass-ceramics containing calcium neodymium(cerium) silicate crystals are good candidate wasteforms for immobilization of lanthanide wastes generated by pyro-processing. - Highlights: • Glass-ceramic wasteforms containing Ca{sub 2}Nd{sub 8-x}Ce{sub x}(SiO{sub 4}){sub 6}O{sub 2} crystals were synthesized to immobilize lanthanide wastes. • Maximum lanthanide oxide waste loading was >26.8 wt.%. • Ce and Nd ions were highly partitioned inside Ca–Nd–silicate crystals compared to glass matrix. • Amounts of Ce and Nd ions released in the material characterization center-type 1 were below the detection limit (0.1 ppb). • Normalized release values performed by a PCT were 2.64• 10{sup −6} g m{sup −2} for Ce ions and 2.19• 10{sup −6} g m{sup −2} for Nd ions.

Fabrication of Polymeric Antireflection Film Manufactured by Anodic Aluminum Oxide Template on Dye-Sensitized Solar Cells

Directory of Open Access Journals (Sweden)

Jenn-Kai Tsai

2017-03-01

Full Text Available In this study, high energy conversion efficient dye-sensitized solar cells (DSSCs were successfully fabricated by attaching a double anti-reflection (AR layer, which is composed of a subwavelength moth-eye structured polymethyl methacrylate (PMMA film and a polydimethylsiloxane (PDMS film. An efficiency of up to 6.79% was achieved. The moth-eye structured PMMA film was fabricated by using an anodic aluminum oxide (AAO template which is simple, low-cost and scalable. The nano-pattern of the AAO template was precisely reproduced onto the PMMA film. The photoanode was composed of Titanium dioxide (TiO2 nanoparticles (NPs with a diameter of 25 nm deposited on the fluorine-doped tin oxide (FTO glass substrate and the sensitizer N3. The double AR layer was proved to effectively improve the short-circuit current density (JSC and conversion efficiency from 14.77 to 15.79 mA/cm2 and from 6.26% to 6.79%, respectively.

Is the adiposity-associated FTO gene variant related to all-cause mortality independent of adiposity?

DEFF Research Database (Denmark)

Zimmermann, E; Ängquist, L H; Mirza, S S

2015-01-01

Previously, a single nucleotide polymorphism (SNP), rs9939609, in the FTO gene showed a much stronger association with all-cause mortality than expected from its association with body mass index (BMI), body fat mass index (FMI) and waist circumference (WC). This finding implies that the SNP has......-up. Linear regression showed that the minor allele of the FTO SNP was associated with greater BMI (n = 169,551; 0.32 kg m(-2) ; 95% CI 0.28-0.32, P ... hazard regression analyses for mortality showed that the hazards ratio (HR) for the minor allele of the FTO SNPs was 1.02 (1.00-1.04, P = 0.097), but the apparent excess risk was eliminated after adjustment for BMI and WC (HR: 1.00; 0.98-1.03, P = 0.662) and for FMI (HR: 1.00; 0.96-1.04, P = 0...

One-step synthesis and properties of monolithic photoluminescent ruby colored cuprous oxide antimony oxide glass nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Som, Tirtha [Glass Science and Technology Section, Glass Division, Central Glass and Ceramic Research Institute, Council of Scientific and Industrial Research (CSIR, India), 196, Raja S.C. Mullick Road, Kolkata 700032 (India); Karmakar, Basudeb, E-mail: basudebk@cgcri.res.in [Glass Science and Technology Section, Glass Division, Central Glass and Ceramic Research Institute, Council of Scientific and Industrial Research (CSIR, India), 196, Raja S.C. Mullick Road, Kolkata 700032 (India)

2011-04-14

Research highlights: > Single-step synthesis of Cu{sub 2}O, Cu{sub y}Sb{sub 2-x}(O,OH){sub 6-7} (y {<=} 2, x {<=} 1) and Cu nanocrystals co-doped novel antimony oxide glass hybrid nanocomposites. > Yellow and orange colored nanocomposites shows size-controlled band gap shift of Cu{sub 2}O. > Red nanocomposite exhibits surface plasmon resonance band due to metallic Cu. > They exhibit broad deep-red photoluminescence emission under various UV excitation wavelengths. - Abstract: Cuprous oxide (Cu{sub 2}O) antimony glass (K{sub 2}O-B{sub 2}O{sub 3}-Sb{sub 2}O{sub 3}) monolithic nanocomposites having brilliant yellow to ruby red color have been synthesized by a single-step melt-quench technique involving in situ thermochemical reduction of Cu{sup 2+} (CuO) by the reducing glass matrix without using any external reducing agent. The X-ray diffraction (XRD), infrared transmission and reflection spectra, and selected area electron diffraction analysis support the reduction of Cu{sup 2+} to Cu{sup +} with the formation of Cu{sub 2}O nanoclusters along with Cu{sub y}Sb{sub 2-x}(O,OH){sub 6-7} (y {<=} 2, x {<=} 1) nanocrystalline phases while Cu{sup 0} nanoclusters are formed at very high Cu concentration. The UV-vis spectra of the yellow and orange colored nanocomposites show size-controlled band gap shift of the semiconductor (Cu{sub 2}O) nanocrystallites embedded in the glasses while the red nanocomposite exhibits surface plasmon resonance band at 529 nm due to metallic Cu. Transmission electron microscopic image advocates the formation of nanocystallites (5-42 nm). Photoluminescence emission studies show broad red emission band around 626 nm under various excitation wavelengths from 210 to 270 nm.

An efficient and low-cost TiO2 compact layer for performance improvement of dye-sensitized solar cells

International Nuclear Information System (INIS)

Yu Hua; Zhang Shanqing; Zhao Huijun; Will, Geoffrey; Liu Porun

2009-01-01

A TiO 2 organic sol was synthesised for the preparation of a compact TiO 2 layer on fluorine-doped tin oxide (FTO) glass by a dip-coating technique. The resultant thin film was used for the fabrication of dye-sensitized solar cells (DSSCs). The compact layer typically has a thickness of ca. 110 nm as indicated by its SEM, and consists of anatase as confirmed by the XRD pattern. Compared with the traditional DSSCs without this compact layer, the solar energy-to-electricity conversion efficiency, short-circuit current and open-circuit potential of the DSSCs with the compact layer were improved by 33.3%, 20.3%, and 10.2%, respectively. This can be attributed to the merits brought by the compact layer. It can effectively improve adherence of TiO 2 to FTO surface, provide a larger TiO 2 /FTO contact area, and reduce the electron recombination by blocking the direct contact between the redox electrolyte and the conductive FTO surface

Raman scattering, electrical and optical properties of fluorine-doped tin oxide thin films with (200) and (301) preferred orientation

Energy Technology Data Exchange (ETDEWEB)

Kim, Chang-Yeoul, E-mail: cykim15@kicet.re.kr [Nano-Convergence Intelligence Material Team, Korea Institute of Ceramic Eng. and Tech., Gasan-digtial-ro 10 Gil 77 Geumcheon-gu, 153-801 Seoul (Korea, Republic of); Riu, Doh-Hyung [Dept. of New Material Sci. and Eng., Seoul National University of Technology, Seoul (Korea, Republic of)

2014-12-15

(200) and (301) preferred oriented fluorine-doped tin oxide (FTO) thin films were fabricated by spray pyrolysis of ethanol-added and water-based FTO precursor solutions, respectively. (200) oriented FTO thin film from ethanol-added solution shows the lower electrical resistivity and visible light transmission than (301) preferred thin film from water-based solution. It is due to the higher carrier concentration and electron mobility in (200) oriented crystals, that is, the lower ionized impurity scattering. The higher electron concentration is related to the higher optical band gap energy, the lower visible light transmission, and the higher IR reflection. For (301) preferred FTO thin films from water-based solution, the lower carrier concentration and electron mobility make the higher electrical resistivity and visible light transmission. Raman scattering analysis shows that IR active modes prominent in (200) oriented FTO thin film are related with the lower electrical resistivity. - Highlights: • We coated fluorine-doped tin oxide thin films with preferred orientation of (200) and (301). • We examine changes in the level of electrical and optical properties with the orientation. • (200) preferred orientation showed lower electrical resistivity and optical transmittance. • (200) oriented thin films have higher electron concentrations that are related with IR active modes.

Identification of a pathogenic FTO mutation by next-generation sequencing in a newborn with growth retardation and developmental delay.

Science.gov (United States)

Daoud, Hussein; Zhang, Dong; McMurray, Fiona; Yu, Andrea; Luco, Stephanie M; Vanstone, Jason; Jarinova, Olga; Carson, Nancy; Wickens, James; Shishodia, Shifali; Choi, Hwanho; McDonough, Michael A; Schofield, Christopher J; Harper, Mary-Ellen; Dyment, David A; Armour, Christine M

2016-03-01

A homozygous loss-of-function mutation p.(Arg316Gln) in the fat mass and obesity-associated (FTO) gene, which encodes for an iron and 2-oxoglutarate-dependent oxygenase, was previously identified in a large family in which nine affected individuals present with a lethal syndrome characterised by growth retardation and multiple malformations. To date, no other pathogenic mutation in FTO has been identified as a cause of multiple congenital malformations. We investigated a 21-month-old girl who presented distinctive facial features, failure to thrive, global developmental delay, left ventricular cardiac hypertrophy, reduced vision and bilateral hearing loss. We performed targeted next-generation sequencing of 4813 clinically relevant genes in the patient and her parents. We identified a novel FTO homozygous missense mutation (c.956C>T; p.(Ser319Phe)) in the affected individual. This mutation affects a highly conserved residue located in the same functional domain as the previously characterised mutation p.(Arg316Gln). Biochemical studies reveal that p.(Ser319Phe) FTO has reduced 2-oxoglutarate turnover and N-methyl-nucleoside demethylase activity. Our findings are consistent with previous reports that homozygous mutations in FTO can lead to rare growth retardation and developmental delay syndrome, and further support the proposal that FTO plays an important role in early development of human central nervous and cardiovascular systems. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Sulphate decomposition and sodium oxide activity in soda-lime-silica glass metls

NARCIS (Netherlands)

Beerkens, R.G.C.

2003-01-01

Reaction equilibrium constants for the sulfate decomposition process, which releases oxygen and sulfur oxide gas in sodalimesilica glass melts, have been determined. The chemical solubility of SO2, probably in the form of sulfite ions in sodalimesilica melts, has also been determined. The chemical

X-ray absorption spectroscopy on phosphoric-salt pellets. Determination of the geometric and electronic structure of metal-oxide doped sodium-phosphate glasses

International Nuclear Information System (INIS)

Brendebach, B.

2004-02-01

Sodium metaphosphate glasses doped with transition metal oxides show characteristic colors. X-ray absorption spectroscopy (XAS) investigations provide information whether the coloration stems from different electronic transitions or changes in the geometrical structure of the glasses. Even though the violet color of MnO y -doped glasses is considered as an evidence for Mn 3+ -ions, Mn K-XAS reveals that the majority of the manganese ions are in the oxidation state +II and have a mixed coordination of four and six oxygen atoms, respectively. The oxygen coordination around the nickel ions in NiO-doped glasses with different metall oxide concentrations is always six. The change of color from citreous to auburn with increasing nickel oxide content is attributed to a systematic change in the bonding characteristic from mainly ionic-like to a small but significant contribution of covalent-like bonding. Analysis of higher coordination shells provides no indication of the formation of metal oxide clusters. (orig.)

Physical and structural properties of Sm3+ ions doped heavy metal oxide containing lanthanum-boro-telluirte glass

Science.gov (United States)

Madhu, A.; Eraiah, B.

2018-05-01

The structural studies of Tellurium oxide substituted by samarium oxide in lathanum-lead-boro-tellurite glass are successfully prepared with physical and optical parameters are determined. Due to the effect of increased number of non-bridging oxygen's in the glass samples few physical parameters are observed to be decreased. For the better structural analysis FTIR was carried out and transformation of BO3 → BO4 is observed. Most effective absorption coefficient OH- group was attained in the present work.

Fluorine-doped tin oxide surfaces modified by self-assembled alkanethiols for thin-film devices

Energy Technology Data Exchange (ETDEWEB)

Alves, A.C.T.; Gomes, D.J.C.; Silva, J.R.; Silva, G.B., E-mail: george@cpd.ufmt.br

2013-08-15

In this work, we have investigated self-assembled monolayers (SAMs) from alkanethiols on fluorine-doped tin oxide (FTO) surfaces, which were used as an anode for thin-film devices prepared from the conductive copolymer so-called sulfonated poly(thiophene-3-[2-(2-methoxyethoxy) ethoxy]-2,5-diyl) (S-P3MEET). The assembled monolayers were characterized by using wetting contact angle, atomic force microscopy, and electrical measurements. The results indicated that dodecanethiol molecules, CH{sub 3}(CH{sub 2}){sub 11}SH, were well assembled on the FTO surfaces. In addition, it was found similar values of wetting contact angle for dodecanethiol assembled on both FTO and Au surfaces. Concerning the thin-film device, current–voltage analysis revealed a hysteresis. This behavior was associated to a charge-trapping effect and also to structural changes of the SAMs. Finally, charge injection capability of tin oxide electrodes can be improved by using SAMs and then this approach can plays an important role in molecular-scale electronic devices.

R-2HG Exhibits Anti-tumor Activity by Targeting FTO/m6A/MYC/CEBPA Signaling.

Science.gov (United States)

Su, Rui; Dong, Lei; Li, Chenying; Nachtergaele, Sigrid; Wunderlich, Mark; Qing, Ying; Deng, Xiaolan; Wang, Yungui; Weng, Xiaocheng; Hu, Chao; Yu, Mengxia; Skibbe, Jennifer; Dai, Qing; Zou, Dongling; Wu, Tong; Yu, Kangkang; Weng, Hengyou; Huang, Huilin; Ferchen, Kyle; Qin, Xi; Zhang, Bin; Qi, Jun; Sasaki, Atsuo T; Plas, David R; Bradner, James E; Wei, Minjie; Marcucci, Guido; Jiang, Xi; Mulloy, James C; Jin, Jie; He, Chuan; Chen, Jianjun

2018-01-11

R-2-hydroxyglutarate (R-2HG), produced at high levels by mutant isocitrate dehydrogenase 1/2 (IDH1/2) enzymes, was reported as an oncometabolite. We show here that R-2HG also exerts a broad anti-leukemic activity in vitro and in vivo by inhibiting leukemia cell proliferation/viability and by promoting cell-cycle arrest and apoptosis. Mechanistically, R-2HG inhibits fat mass and obesity-associated protein (FTO) activity, thereby increasing global N 6 -methyladenosine (m 6 A) RNA modification in R-2HG-sensitive leukemia cells, which in turn decreases the stability of MYC/CEBPA transcripts, leading to the suppression of relevant pathways. Ectopically expressed mutant IDH1 and S-2HG recapitulate the effects of R-2HG. High levels of FTO sensitize leukemic cells to R-2HG, whereas hyperactivation of MYC signaling confers resistance that can be reversed by the inhibition of MYC signaling. R-2HG also displays anti-tumor activity in glioma. Collectively, while R-2HG accumulated in IDH1/2 mutant cancers contributes to cancer initiation, our work demonstrates anti-tumor effects of 2HG in inhibiting proliferation/survival of FTO-high cancer cells via targeting FTO/m 6 A/MYC/CEBPA signaling. Copyright © 2017 Elsevier Inc. All rights reserved.

An Obesity-Related FTO Variant and the Risk of Preeclampsia in a Finnish Study Population

Directory of Open Access Journals (Sweden)

Miira Klemetti

2011-01-01

Full Text Available Previous studies have demonstrated a common variant of the obesity and fat mass-related FTO gene, rs9939609, to be associated with obesity, type 2 diabetes, and elevated blood pressure. We investigated whether the FTO SNP rs9939609 is associated with the risk of preeclampsia (PE in a Finnish study population. 485 women with prior PE and 449 women who had given birth after a normotensive pregnancy were genotyped (TaqMan for the SNP rs9939609. The prevalences of genotypes AA, AT, and TT were 15%, 53%, and 32%, respectively, among the PE cases, and 16%, 47%, and 37%, respectively, among the controls (P=0.199. We found no evidence of an association between the FTO SNP rs9939609 and PE. However, our cases were dominated by severe, early-onset PE. Thus, we are unable to exclude an association with the milder, later-onset form of the disease in which the role of maternal metabolic predisposition could be more significant.

A study of the local structure around Eu3+ ions in oxide glasses using Moessbauer spectroscopy

International Nuclear Information System (INIS)

Todoroki, S.; Hirao, K.; Soga, N.

1993-01-01

The local structure around Eu 3+ ions in several oxide glasses (silicate, germanate and borophosphate glasses) was investigated by using 151 Eu Moessbauer spectroscopy. It was found that the isomer shift (IS) of silicate and borophosphate glasses was independent of the sodium content, but that of germanate glasses was not. This means the first coordination sphere around Eu 3+ ions in silicate glasses is insensitive to the composition of the glass matrix. It is assumed that, regardless of the sodium content, Eu 3+ ions in silicate glasses attract a certain amount of nonbridging oxygen (NBO, Si-O direct difference ) when incorporated stably into silicate glass matrix, because NBO is the only species donating negative charge. For germanate glasses, the behavior of IS is considered to be related to the resence of GeO 6/2 octahedra. On the basis of experimental results, the coordination models of Eu 3+ in these systems are proposed. (orig.)

Indications for potential parent-of-origin effects within the FTO gene.

Directory of Open Access Journals (Sweden)

Xuanshi Liu

Full Text Available Genome-Wide Association Studies (GWAS were successfully applied to discover associations with obesity. However, the GWAS design is usually based on unrelated individuals and inheritance information on the parental origin of the alleles is missing. Taking into account parent-of-origin may provide further insights into the genetic mechanisms contributing to obesity. We hypothesized that there may be variants within the robustly replicated fat mass and obesity associated (FTO gene that may confer different risk for obesity depending on transmission from mother or father. Genome-wide genotypes and pedigree information from the Sorbs population were used. Phased genotypes among 525 individuals were generated by AlphaImpute. Subsequently, 22 SNPs within FTO introns 1 to 3 were selected and parent-of-origin specific association analyses were performed using PLINK. Interestingly, we identified several SNPs conferring different genetic effects (P≤0.05 depending on parental origin--among them, rs1861868, rs1121980 and rs9939973 (all in intron 1. To confirm our findings, we investigated the selected variants in 705 German trios comprising an (extremely obese child or adolescent and both parents. Again, we observed evidence for POE effects in intron 2 and 3 (P≤0.05 as indicated by the parental asymmetry test. Our results suggest that the obesity risk transmitted by several FTO variants may depend on the parental origin of the allele. Larger family-based studies are warranted to replicate our findings.

Mixed conductivity studies in silver oxide based barium vanado-tellurite glasses

International Nuclear Information System (INIS)

Pant, Meenakshi; Kanchan, D.K.; Sharma, Poonam; Jayswal, Manish S.

2008-01-01

The dc conductivity and frequency dependent ac conductivity of the quaternary glass system x(BaO:1.5 Ag 2 O)-(95 - x)V 2 O 5 -5TeO 2 , are reported in the frequency range 1 Hz to 32 MHz in the temperature range from room temperature to 433 K. The dc conductivity measured in high temperature range increased with transition metal oxide content while the activation range decreased. The conductivity arises mainly from polaron hopping between V 4+ and V 5+ ions. High temperature conductivity data satisfy Mott's small polaron hopping model. It is found that a mechanism of non-adiabatic hopping is the most appropriate conduction model for these glasses. A power law behavior σ(ω) = σ dc + Aω n (with 0 < n < 1) is well exhibited by the ac conductivity data of the glasses. The activation energy calculated from both the relaxation time and dc conductivity is found to be nearly same in both the cases. A scaling of the conductivity spectra with respect to temperature and composition is attempted and it is observed that the relaxation dynamics of charge carriers in the present glasses is independent of temperature and composition

FTO genotype, dietary protein, and change in appetite: the Preventing Overweight Using Novel Dietary Strategies trial123

Science.gov (United States)

Huang, Tao; Li, Yanping; Hu, Frank B; Bray, George A; Sacks, Frank M; Williamson, Donald A; Qi, Lu

2014-01-01

Background: A common obesity-risk variant rs9939609 in the fat mass– and obesity-associated (FTO) gene was recently shown to affect appetite, and the gene is sensitive to the regulation of amino acids. Objective: We examined the interaction between FTO genotype and protein intake on the long-term changes in appetite in a randomized controlled trial. Design: We genotyped FTO rs9939609 in 737 overweight adults in the 2-y Preventing Overweight Using Novel Dietary Strategies trial and assessed 4 appetite-related traits including cravings, fullness, hunger, and prospective consumption. Results: We showed that dietary protein significantly modified genetic effects on changes in food cravings and appetite scores at 6 mo after adjustment for age, sex, ethnicity, baseline body mass index, weight change, and baseline value for respective outcomes (P-interaction = 0.027 and 0.048, respectively). The A allele was associated with a greater decrease in food cravings and appetite scores in participants with high-protein–diet intake (P = 0.027 and 0.047, respectively) but not in subjects in the low-protein–diet group (P = 0.384 and 0.078, respectively). The weight regain from 6 to 24 mo attenuated gene-protein interactions. Protein intakes did not modify FTO genotype effects on other appetite measures. Conclusion: Our data suggest that individuals with the FTO rs9939609 A allele might obtain more benefits in a reduction of food cravings and appetite by choosing a hypocaloric and higher-protein weight-loss diet. This trial was registered at clinicaltrials.gov as NCT00072995. PMID:24622803

The FTO A/T Polymorphism and Elite Athletic Performance: A Study Involving Three Groups of European Athletes

Science.gov (United States)

Eynon, Nir; Nasibulina, Emiliya S.; Banting, Lauren K.; Cieszczyk, Pawel; Maciejewska-Karlowska, Agnieszka; Sawczuk, Marek; Bondareva, Elvira A.; Shagimardanova, Roza R.; Raz, Maytal; Sharon, Yael; Williams, Alun G.; Ahmetov, Ildus I.

2013-01-01

Objective The FTO A/T polymorphism (rs9939609) is a strong candidate to influence obesity-related traits. Elite athletes from many different sporting disciplines are characterized by low body fat. Therefore, the aim of this study was to assess whether athletic status is associated with the FTO A/T polymorphism. Subjects and Methods A large cohort of European Caucasians from Poland, Russia and Spain were tested to examine the association between FTO A/T polymorphism (rs9939609) and athletic status. A total of 551 athletes were divided by type of sport (endurance athletes, n = 266 vs. sprint/power athletes, n = 285) as well as by level of competition (elite-level vs. national-level). The control group consisted of 1,416 ethnically-matched, non-athletic participants, all Europeans. Multinomial logistic regression analyses were conducted to assess the association between FTO A/T genotypes and athletic status/competition level. Results There were no significantly greater/lesser odds of harbouring any type of genotype when comparing across athletic status (endurance athletes, sprint/power athletes or control participants). These effects were observed after controlling for sex and nationality. Furthermore, no significantly greater/lesser odds ratios were observed for any of the genotypes in respect to the level of competition (elite-level vs. national-level). Conclusion The FTO A/T polymorphism is not associated with elite athletic status in the largest group of elite athletes studied to date. Large collaborations and data sharing between researchers, as presented here, are strongly recommended to enhance the research in the field of exercise genomics. PMID:23573268

The FTO A/T polymorphism and elite athletic performance: a study involving three groups of European athletes.

Directory of Open Access Journals (Sweden)

Nir Eynon

Full Text Available The FTO A/T polymorphism (rs9939609 is a strong candidate to influence obesity-related traits. Elite athletes from many different sporting disciplines are characterized by low body fat. Therefore, the aim of this study was to assess whether athletic status is associated with the FTO A/T polymorphism.A large cohort of European Caucasians from Poland, Russia and Spain were tested to examine the association between FTO A/T polymorphism (rs9939609 and athletic status. A total of 551 athletes were divided by type of sport (endurance athletes, n = 266 vs. sprint/power athletes, n = 285 as well as by level of competition (elite-level vs. national-level. The control group consisted of 1,416 ethnically-matched, non-athletic participants, all Europeans. Multinomial logistic regression analyses were conducted to assess the association between FTO A/T genotypes and athletic status/competition level.There were no significantly greater/lesser odds of harbouring any type of genotype when comparing across athletic status (endurance athletes, sprint/power athletes or control participants. These effects were observed after controlling for sex and nationality. Furthermore, no significantly greater/lesser odds ratios were observed for any of the genotypes in respect to the level of competition (elite-level vs. national-level.The FTO A/T polymorphism is not associated with elite athletic status in the largest group of elite athletes studied to date. Large collaborations and data sharing between researchers, as presented here, are strongly recommended to enhance the research in the field of exercise genomics.

Enhanced photocatalytic activity of wool-ball-like TiO2 microspheres on carbon fabric and FTO substrates

Science.gov (United States)

Zhang, Yu; Gu, Jian; Zhang, Mengqi

2018-06-01

The wool-ball-like TiO2 microspheres on carbon fabric (TiO2-CF) and FTO substrates (TiO2-FTO) have been synthesized by a facile hydrothermal method in alkali environment, using commercial TiO2 (P25) as precursors. The XRD results indicate that the as-prepared TiO2 have good crystallinity. And the SEM images show that the wool-ball-like TiO2 microspheres with a diameter of 2-3 μm are composed of TiO2 nanowires, which have a diameter of 50 nm. The photocatalytic behavior of the wool-ball-like TiO2 microspheres, TiO2-CF and TiO2-FTO under ultraviolet light was investigated by a pseudo first-order kinetic model, using methyl orange (MO) as pollutant. The wool-ball-like TiO2 microspheres obtained a degradation rate constant (Kap) of 6.91×10-3 min-1 . The Kap values of TiO2-FTO and TiO2-CF reach 13.97×10-3 min-1 and 11.80×10-3 min-1, which are 2.0 and 1.7 times higher than that of pristine wool-ball-like TiO2 microspheres due to the "sum effect" between TiO2 and substrates. This study offers a facile hydrothermal method to prepare wool-ball-like TiO2 microspheres on CF and FTO substrates, which will improve the recyclability of phtocatalysts and can be extended to other fields.

FTO variants are associated with obesity in the Chinese and Malay populations in Singapore.

Science.gov (United States)

Tan, Jonathan T; Dorajoo, Rajkumar; Seielstad, Mark; Sim, Xue Ling; Ong, Rick Twee-Hee; Chia, Kee Seng; Wong, Tien Yin; Saw, Seang Mei; Chew, Suok Kai; Aung, Tin; Tai, E-Shyong

2008-10-01

Association between genetic variants at the FTO locus and obesity has been consistently observed in populations of European ancestry and inconsistently in non-Europeans. The aim of this study was to examine the effects of FTO variants on obesity and type 2 diabetes in Southeast Asian populations. We examined associations between nine previously reported FTO single nucleotide polymorphisms (SNPs) with obesity, type 2 diabetes, and related traits in 4,298 participants (2,919 Chinese, 785 Malays, and 594 Asian Indians) from the 1998 Singapore National Health Survey (NHS98) and 2,996 Malays from the Singapore Malay Eye Study (SiMES). All nine SNPs exhibited strong linkage disequilibrium (r(2) = 0.6-0.99), and minor alleles were associated with obesity in the same direction as previous studies with effect sizes ranging from 0.42 to 0.68 kg/m(2) (P Chinese, 0.65 to 0.91 kg/m(2) (P Malays, and 0.52 to 0.64 kg/m(2) (P Malays after adjustment for age, sex, smoking, alcohol consumption, and exercise. The variants were also associated with type 2 diabetes, though not after adjustment for BMI (with the exception of the SiMES Malays: odds ratio 1.17-1.22; P Chinese and Malays in Singapore. Our data do not support the hypothesis that differences in allele frequency or genetic architecture underlie the lack of association observed in some populations of Asian ancestry. Examination of gene-environment interactions involving variants at this locus may provide further insights into the role of FTO in the pathogenesis of human obesity and diabetes.

Effect of Gamma Irradiation on Some Properties of Bismuth Silicate Glasses and Their Glass Derivatives

International Nuclear Information System (INIS)

Abo Hussein, E.M.K.

2014-01-01

Glasses containing bismuth oxide have attracted considerable attention, although it is non-conventional glass forming oxide, but it has wide applications. In this work, it is aimed to prove that bismuth silicate glass can act as a good shielding material for γ- rays. For this purpose glass containing 20% bismuth oxide and 80% SiO_2 was prepared using melting-annealing technique. Also effects of adding some alkali heavy metal oxides to this glass such as PbO, BaO or SrO were also studied. The formed glasses were also heat treated at 450 degree C for 4 hours to give the corresponding heat treated glasses. Electron Paramagnetic Resonance (EPR) measurements show that the prepared glasses and heat treated glasses have very good stability when exposed to γ- irradiation, which encourage the assumption of using these glasses as gamma ray shielding materials. Many properties have been investigated, such as density to understand the structural properties, also mechanical properties were verified by measuring microhardness, while the chemical resistance was identified by testing their durability in both acidic and basic solutions. The EPR results were supported by measuring electrical conductivity of the glass and heat treated glass samples at different temperatures ranging from 298 to 553 K, which proved that these glasses have very low conductivity even at high temperature. The formed phases of heat treated glass or glass ceramic samples were demonstrated by means of X-ray diffraction (XRD). Also studying the structure of glasses and heat treated glasses before and after irradiation was investigated by the Infrared transmitting spectra. Calculations of optical band gap energies were demonstrated for some selected glasses and heat treated glasses from the data of UV optical absorption spectra to support the probability of using these bismuth silicate glasses for gamma radiation shielding processing.

Properties of Semiconductors: Synthesis of Oriented ZnO for Photoelectrochemistry and Photoremediation

Science.gov (United States)

Koenig, Emma; Jacobs, Ari; Lisensky, George

2017-01-01

Semiconductors are an important class of materials; preparing ZnO nanorods allows semiconducting properties to be easily observed. The week before lab, groups of four students take 15 min to setup two fluorine-doped tin oxide glass (FTO) slides in a zinc nitrate and hexamethylenetetramine solution stored at 90°C until the next lab. Hexagonal ZnO…

High insulation foam glass material from waste cathode ray tube panel glass

DEFF Research Database (Denmark)

König, Jakob; Petersen, Rasmus Rosenlund; Yue, Yuanzheng

. In general CRT consists of two types of glasses: barium/strontium containing glass (panel glass) and lead containing glass (funnel and panel glass). In this work we present the possibility to produce high performance insulation material from the recycled lead-free glass. We studied the influence of foaming...... between 750 and 850°C. We investigated the influence of milling time, particle size, foaming and oxidizing agent concentrations, temperature and time on the foaming process, foam density, foam porosity and homogeneity. Only moderate foaming was observed in carbon containing samples, while the addition...... of the oxidizing agent greatly improved the foaming quality. The results showed that the amount of oxygen available from the glass is not sufficient to combust all of the added carbon, therefore, additional oxygen was supplied via manganese reduction. In general, a minimum in the foam glass density was observed...

Distribution of oxides in a Zr-Cu-Ni-Al-Nb-Si bulk metallic glass

Energy Technology Data Exchange (ETDEWEB)

Heinrich, Jochen; Busch, Ralf [Chair of Metallic Materials, Saarland University, PO Box 151150, 66041 Saarbruecken (Germany); Mueller, Frank; Huefner, Stefan [Chair of Experimental Physics, Saarland University, PO Box 151150, 66041 Saarbruecken (Germany)

2010-07-01

The course of oxide presence with distance from the sample surface and bonding partner was studied for the bulk metallic glass with the nominal composition Zr{sub 57.9}Cu{sub 15.4}Ni{sub 12.7}Al{sub 10.2}Nb{sub 2.8}Si{sub 1} (at%) by X-ray photoelectron spectroscopy (XPS). Investigated specimens are taken from vacuum quench-cast rods subjected to oxidation at room temperature and atmosphere. Binding energies were determined in various depths using ion beam ablation of up to 100 nanometers. XPS spectra confirm oxidation primarily of the pure zirconium and aluminum constituents, all other peaks correspond to metallic bonds. While the surface area shows a passivating zirconia layer a few nanometers thick, oxygen is bonded predominantly with aluminum inside the bulk. Since the concentration of oxygen is a crucial factor in the crystallization behavior of bulk metallic glass forming liquids on basis of oxygen affine metals, so far only high purity materials were thought to be suitable. The findings in this study, however, are promising for alloys with industrial grade elements with sufficient glass forming ability. Comparisons of the alloy with differing oxygen content support the conclusion that aluminum acts as an appropriate scavenger for both adsorbed and large amounts of intrinsic oxygen in zirconium based amorphous metals.

Effects of process parameters on sheet resistance uniformity of fluorine-doped tin oxide thin films

Science.gov (United States)

Hudaya, Chairul; Park, Ji Hun; Lee, Joong Kee

2012-01-01

An alternative indium-free material for transparent conducting oxides of fluorine-doped tin oxide [FTO] thin films deposited on polyethylene terephthalate [PET] was prepared by electron cyclotron resonance - metal organic chemical vapor deposition [ECR-MOCVD]. One of the essential issues regarding metal oxide film deposition is the sheet resistance uniformity of the film. Variations in process parameters, in this case, working and bubbler pressures of ECR-MOCVD, can lead to a change in resistance uniformity. Both the optical transmittance and electrical resistance uniformity of FTO film-coated PET were investigated. The result shows that sheet resistance uniformity and the transmittance of the film are affected significantly by the changes in bubbler pressure but are less influenced by the working pressure of the ECR-MOCVD system.

Adhesion mapping of chemically modified and poly(ethylene oxide)-grafted glass surfaces.

Science.gov (United States)

Jogikalmath, G; Stuart, J K; Pungor, A; Hlady, V

1999-08-01

Two-dimensional mapping of the adhesion pull-off forces was used to study the origin of surface heterogeneity in the grafted poly(ethylene oxide) (PEO) layer. The variance of the pull-off forces measured over the μm-sized regions after each chemical step of modifying glass surfaces was taken to be a measure of the surface chemical heterogeneity. The attachment of γ-glycidoxypropyltrimethoxy silane (GPS) to glass decreased the pull-off forces relative to the clean glass and made the surface more uniform. The subsequent hydrolysis of the terminal epoxide groups resulted in a larger surface heterogeneity which was modeled by two populations of the terminal hydroxyl groups, each with its own distribution of adhesion forces and force variance. The activation of the hydroxyls with carbonyldiimmidazole (CDI) healed the surface and lowered its adhesion, however, the force variance remained rather large. Finally, the grafting of the α,ω-diamino poly(ethyleneoxide) chains to the CDI-activated glass largely eliminated adhesion except at a few discrete regions. The adhesion on the PEO grafted layer followed the Poisson distribution of the pull-off forces. With the exception of the glass surface, a correlation between the water contact angles and the mean pull-off forces measured with the Si(3)N(4) tip surfaces was found for all modified glass surfaces.

Novel Synthesis of Calcium Oxide-Aluminum Oxide Glasses

Science.gov (United States)

Weber, J. K. Richard; Tangeman, Jean A.; Key, Thomas S.; Hiera, Kirsten J.; Paradis, Paul-Francois; Ishikawa, Takehiko; Yu, Jianding; Yoda, Shinichi

2002-05-01

Binary Al2O3:CaO glasses containing 36-50 mole% Al2O3 were synthesized by containerless processing of liquids in nitrogen using aerodynamic and a pressurized electrostatic-aerodynamic levitator. The critical cooling rate for glass formation RC under containerless conditions was ca. 70 K/s. The Vickers hardness of the glasses was 775-785; and the infrared transmission extended to approximately 5500 nm. The work function of the 36 mole% Al2O3 composition was 3.7 eV at 1100 K.

Fatness-Associated FTO Gene Variant Increases Mortality Independent of Fatness - in Cohorts of Danish Men

DEFF Research Database (Denmark)

Zimmermann, E; Kring, SI; Berentzen, TL

2009-01-01

The A-allele of the single nucleotide polymorphism (SNP), rs9939609, in the FTO gene is associated with increased fatness. We hypothesized that the SNP is associated with morbidity and mortality through the effect on fatness. METHODOLOGY/PRINCIPAL FINDINGS: In a population of 362,200 Danish young...... prior to death suggested a general protective effect of the TT genotype, whereas there were only weak associations with disease incidence, except for diseases of the nervous system. CONCLUSION: Independent of fatness, the A-allele of the FTO SNP appears to increase mortality of a magnitude similar...

Obesity-related polymorphisms and their associations with the ability to regulate fat oxidation in obese europeans

DEFF Research Database (Denmark)

Corpeleijn, Eva; Petersen, Liselotte; Holst, Claus

2010-01-01

for fat oxidation, insulin resistance, and obesity, including FTO. Energy expenditure (EE) and fat oxidation were measured with indirect calorimetry during fasting and 3 h after a high fat load containing 95 energy% of fat (60% saturated fat, energy content 50% of estimated resting EE) in 722 obese......Both obesity and insulin resistance have been related to low fat oxidation rates, which may be genetically determined. The association between variation in fat oxidation rates among obese subjects and genotype was studied for 42 common single-nucleotide polymorphisms (SNPs) in 26 candidate genes.......01) was related to increased fat oxidation in the fasting state. The ability to increase fat oxidation after a high fat load was increased in subjects with -174 G>C IL6 (rs1800795) (P = 0.01). Effect sizes range from 1.1 to 3.1% differences in fat oxidation (expressed as % of EE). FTO rs9939609 was not related...

Determining optical and radiation characteristics of cathode ray tubes' glass to be reused as radiation shielding glass

Science.gov (United States)

Zughbi, A.; Kharita, M. H.; Shehada, A. M.

2017-07-01

A new method of recycling glass of Cathode Ray Tubes (CRTs) has been presented in this paper. The glass from CRTs suggested being used as raw materials for the production of radiation shielding glass. Cathode ray tubes glass contains considerable amounts of environmentally hazardous toxic wastes, namely heavy metal oxides such as lead oxide (PbO). This method makes CRTs glass a favorable choice to be used as raw material for Radiation Shielding Glass and concrete. The heavy metal oxides increase its density, which make this type of glass nearly equivalent to commercially available shielding glass. CRTs glass have been characterized to determine heavy oxides content, density, refractive index, and radiation shielding properties for different Gamma-Ray energies. Empirical methods have been used by using the Gamma-Ray source cobalt-60 and computational method by using the code XCOM. Measured and calculated values were in a good compatibility. The effects of irradiation by gamma rays of cobalt-60 on the optical transparency for each part of the CRTs glass have been studied. The Results had shown that some parts of CRTs glass have more resistant to Gamma radiation than others. The study had shown that the glass of cathode ray tubes could be recycled to be used as radiation shielding glass. This proposed use of CRT glass is only limited to the available quantity of CRT world-wide.

3 and 4 oxidation state element solubilities in borosilicate glasses. Implement to actinides in nuclear glasses

International Nuclear Information System (INIS)

Cachia, J.N.

2005-12-01

In order to ensure optimal radionuclides containment, the knowledge of the actinide loading limits in nuclear waste glasses and also the comprehension of the solubilization mechanisms of these elements are essential. A first part of this manuscript deals with the study of the differences in solubility of the tri and tetravalent elements (actinides and surrogates) particularly in function of the melting temperature. The results obtained indicate that trivalent elements (La, Gd, Nd, Am, Cm) exhibit a higher solubility than tetravalent elements (Hf, Th, Pu). Consequently, it was planned to reduce plutonium at the oxidation state (III), the later being essentially tetravalent in borosilicate glasses. An innovating reduction process of multi-valent elements (cerium, plutonium) using silicon nitride has been developed in a second part of this work. Reduced plutonium-bearing glasses synthesized by Si 3 N 4 addition made it possible to double the plutonium solubility from 2 to 4 wt% at 1200 deg C. A structural approach to investigate the differences between tri and tetravalent elements was finally undertaken. These investigations were carried out by X-rays Absorption Spectroscopy (EXAFS) and NMR. Trivalent rare earth and actinide elements seem to behave as network modifiers while tetravalent elements rather present true intermediaries' behaviour. (author)

Physical Activity Attenuates the Influence of FTO Variants on Obesity Risk

DEFF Research Database (Denmark)

Oskari Kilpeläinen, Tuomas; Qi, Lu; Brage, Soren

2011-01-01

Background The FTO gene harbors the strongest known susceptibility locus for obesity. While many individual studies have suggested that physical activity (PA) may attenuate the effect of FTO on obesity risk, other studies have not been able to confirm this interaction. To confirm or refute......>0.8]) and PA were invited to participate, regardless of ethnicity or age of the participants. PA was standardized by categorizing it into a dichotomous variable (physically inactive versus active) in each study. Overall, 25% of adults and 13% of children were categorized as inactive. Interaction analyses were.......20–1.26), but PA attenuated this effect (pinteraction = 0.001). More specifically, the minor allele of rs9939609 increased the odds of obesity less in the physically active group (odds ratio = 1.22/allele, 95% CI 1.19–1.25) than in the inactive group (odds ratio = 1.30/allele, 95% CI 1...

Association between fat mass- and obesity-associated (FTO gene polymorphism and polycystic ovary syndrome: a meta-analysis.

Directory of Open Access Journals (Sweden)

Xianli Cai

Full Text Available Many studies have investigated the relationship between FTO gene polymorphism and polycystic ovary syndrome (PCOS susceptibility but revealed mixed results. In this study, we aimed to perform a meta-analysis to clarify this association.Published literature from PubMed, Embase and CNKI was retrieved. Meta-analysis was performed to calculate pooled odds ratio (OR with 95% confidence interval (CI using the random- or fix- effects model.A total of 5 studies (4778 cases and 4272 controls were included in our meta-analysis. The results suggested that FTO rs9939609 polymorphism (or its proxy was marginally associated with PCOS risk after adjustment for body mass index (BMI (OR = 1.26; 95%CI: 1.02-1.55. However, the marginal association was not stable after sensitivity analysis. In the subgroup analysis by ethnicity, the association was significant in East Asians (OR = 1.43, 95%CI = 1.30-1.59 but not in Caucasians (OR = 1.04, 95%CI = 0.85-1.29.Our present meta-analysis indicated that FTO rs9939609 polymorphism (or its proxy might not be associated with risk of PCOS in overall population. However, in East Asians, there might be a direct association between FTO variant and PCOS risk, which is independent of BMI (adiposity.

Electrochromic Glasses.

Science.gov (United States)

1980-07-31

this glass and that dipole-dipole correlations contribute to the "ferroelectric-like" character of this amorphous system. The TeO2 -W03 glasses can only...shows the dielectric constant and Fig. I(b) glass from pure TeO2 ot pure WO. In addition, glass the tan 8 of the WO glass as a function of temperature... glasses containing WO, in various glass forming nitworks of LifO-B1O0, Na:O-BzO,, and TeO2 were prepared from reagent grade oxides at 800 C - 9SO C in

Self-cleaning glasses containing nanostructured titanium oxide

International Nuclear Information System (INIS)

Araujo, A.; Alves, A.K.; Berutti, F.A.; Bergmann, C.P.

2010-01-01

Using the electrospinning technique nanofibers of titanium oxide were synthesized. As precursor materials, titanium propoxide and a solution of polyvinylpyrrolidone were used. After the electrospinning process, the non-tissue material obtained was heat treated and characterized by X-ray diffraction to determine the phase crystallinity, and SEM to analyze the microstructure of the fibers. After ultrasound dispersion of this material in isopropyl alcohol, the glass coatings were made by dip-coating methodology. The removal velocity was kept constant, but the solution composition was varied to obtain a transparent and photo active film. The film was characterized by the contact angle of a water droplet in its surface (hydrophilicity), the transparency was evaluated using a spectrophotometer and the photocatalytic activity of the film was also evaluated. (author)

β-cyclodextrin functionalized on glass micro-particles: A green catalyst for selective oxidation of toluene to benzaldehyde

Energy Technology Data Exchange (ETDEWEB)

Tahir, M. Nazir, E-mail: tahir.muhammad_nazir@courrier.uqam.ca [Department of Chemistry and Bioscience, Aalborg University, Frederik Bajers Vej 7H, DK-9220, Aalborg East (Denmark); Department of Chemistry, University of Quebec at Montreal, QC, H3C 3P8 (Canada); Nielsen, Thorbjørn T.; Larsen, Kim L. [Department of Chemistry and Bioscience, Aalborg University, Frederik Bajers Vej 7H, DK-9220, Aalborg East (Denmark)

2016-12-15

Highlights: • Functionalization of βCD onto glass micro-particles (GMP-βCD). • Application of GMP-βCD as a green catalyst for the oxidation of toluene. • 82% yield at room temperature. • Repeated use of the catalyst for several cycles. - Abstract: Oxidation of toluene is considered an important process which often requires high temperatures and specific conditions along with heavy-metals based catalysts. In this study, we have developed a green catalyst by functionalizing beta-cyclodextrin onto glass micro-particle surfaces. All surfaces were characterized by X-ray photoelectron spectroscopy and applied to catalyze the selective oxidation of toluene into benzaldehyde (82% yield) at room temperature. The catalyst was stable and could be used repeatedly for several cycles without losing efficiency.

Electrical characterization of strontium titanate borosilicate glass ceramics system with bismuth oxide addition using impedance spectroscopy

International Nuclear Information System (INIS)

Thakur, O.P.; Kumar, Devendra; Parkash, Om; Pandey, Lakshman

2003-01-01

The ac electrical data, measured in the frequency range 0.1 kHz-1 MHz, were used to study the electrical response of strontium titanate borosilicate glass ceramic system with bismuth oxide addition. Complex plane plots from these electrical data for various glass ceramic samples reveal contributions from simultaneously operating polarization mechanisms to overall dielectric behavior. The complex modulus (M * ) representation of electrical data for various glass ceramic samples were found to be more informative. Equivalent circuit models, which represent the electrical behavior of glass ceramic samples, were determined using complex non-linear least square (CNLS) fitting. An attempt has been made to understand the dielectric behavior of various glass ceramics in terms of contributions arising from different polarization processes occurring at glassy matrix, crystalline phases, glass to crystal interface region and blocking electrodes. Glass ceramics containing SrTiO 3 and TiO 2 (rutile) phases show thermally stable dielectric behavior

Lead recovery and high silica glass powder synthesis from waste CRT funnel glasses through carbon thermal reduction enhanced glass phase separation process

Energy Technology Data Exchange (ETDEWEB)

Xing, Mingfei [Henan Key Laboratory Cultivation Base of Mine Environmental Protection and Ecological Remediation, Henan Polytechnic University, Jiaozuo 454000 Henan China (China); Institute of Resource and Environment, Henan Polytechnic University, Jiaozuo 454000 Henan China (China); Fu, Zegang [Institute of Resource and Environment, Henan Polytechnic University, Jiaozuo 454000 Henan China (China); Wang, Yaping, E-mail: wangyp326@163.com [School of Surveying and Land Information Engineering, Henan Polytechnic University, Jiaozuo 454000, Henan China (China); Wang, Jingyu [Institute of Resource and Environment, Henan Polytechnic University, Jiaozuo 454000 Henan China (China); Zhang, Zhiyuan [Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China)

2017-01-15

Highlights: • CRT funnel glass was remelted with B{sub 2}O{sub 3} in reducing atmosphere. • A part of PbO was reduced into Pb and detached from the glass phase. • The rest of PbO and other metal oxides were mainly concentrated in the B{sub 2}O{sub 3} phase. • PbO enriched in the interconnected B{sub 2}O{sub 3} phase can be completely leached out by HNO{sub 3}. • High silica glass powder(SiO{sub 2} purity >95%) was obtained after the leaching process. - Abstract: In this study, a novel process for the removal of toxic lead from the CRT funnel glass and synchronous preparation of high silica glass powder was developed by a carbon-thermal reduction enhanced glass phase separation process. CRT funnel glass was remelted with B{sub 2}O{sub 3} in reducing atmosphere. In the thermal process, a part of PbO contained in the funnel glass was reduced into metallic Pb and detached from the glass phase. The rest of PbO and other metal oxides (including Na{sub 2}O, K{sub 2}O, Al{sub 2}O{sub 3,} BaO and CaO) were mainly concentrated in the boric oxide phase. The metallic Pb phase and boric oxide phase were completely leached out by 5 mol/L HNO{sub 3}. The lead removal rate was 99.80% and high silica glass powder (SiO{sub 2} purity >95 wt%) was obtained by setting the temperature, B{sub 2}O{sub 3} added amount and holding time at 1000 °C, 20% and 30 mins, respectively. The prepared high silicate glass powders can be used as catalyst carrier, semipermeable membranes, adsorbents or be remelted into high silicate glass as an ideal substitute for quartz glass. Thus this study proposed an eco-friendly and economical process for recycling Pb-rich electronic glass waste.

FTO polymorphism, cardiorespiratory fitness, and obesity in Brazilian youth.

Science.gov (United States)

Reuter, Cézane Priscila; Rosane De Moura Valim, Andréia; Gaya, Anelise Reis; Borges, Tássia Silvana; Klinger, Elisa Inês; Possuelo, Lia Gonçalves; Franke, Silvia Isabel Rech; Kmetzsch, Lívia; Vainstein, Marilene Henning; Prá, Daniel; Burgos, Miria Suzana

2016-05-01

The aim of the present study was to evaluate the relationship between the rs9939609 fat mass and obesity-associated (FTO) polymorphism and cardiorespiratory fitness (CRF) with overweight/obesity outcomes in youth. This study included 420 youths, comprising 211 boys and 209 girls aged 7-17. Overweight/obesity were evaluated by body mass index (BMI), waist circumference (WC), and the percentage of fat (PF) according to two skinfold thickness measurements. Genotyping of the rs9939609 polymorphism was conducted using real-time Polymerase Chain Reaction (PCR) utilizing TaqMan(®) probes, and CRF was evaluated through a 9-minute run/walk test, categorized as fit or unfit. Logistic regression was utilized to evaluate a possible association between the polymorphism and CRF, with three obesity indicators evaluated. Individuals with the genotype risk (AA) of FTO polymorphism rs9939609 showed higher prevalence of overweight/obesity, as evaluated by BMI (OR: 3.21; CI: 1.71-6.05), WC (OR: 2.59; CI: 1.35-4.97), and PF (OR: 2.59; CI: 1.36-4.92). Additionally, students with the AA genotype in the unfit model had a significant odds ratio for obesity (OR: 4.40; CI: 1.83-10.61 for BMI; OR: 3.54; CI: 1.58-7.96 for WC), whereas we did not observe associations between the AA genotype with BMI and WC using the fit model. Conversely, PF was associated with the AA genotype only in the fit model (OR: 3.24; CI: 1.26-8.34). This study demonstrated that the rs9939609 (FTO) polymorphism showed a relationship with obesity in the population studied and an interaction with CRF. Students with low levels of CRF and the AA genotype have a higher risk of being overweight/obese. This association was not found in students with higher levels of CRF. Am. J. Hum. Biol. 28:381-386, 2016. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

The common FTO variant rs9939609 is not associated with BMI in a longitudinal study on a cohort of Swedish men born 1920-1924

Directory of Open Access Journals (Sweden)

Lannfelt Lars

2009-12-01

Full Text Available Abstract Background Common FTO (fat mass and obesity associated gene variants have recently been strongly associated with body mass index and obesity in several large studies. Here we set out to examine the association of the FTO variant rs9939609 with BMI in a 32 year follow up study of men born 1920-1924. Moreover, we analyzed the effect of physical activity on the different genotypes. Methods The FTO rs9936609 was genotyped using an Illumina golden gate assay. BMI was calculated using standard methods and body fat was estimated by measuring skinfold thickness using a Harpenden caliper. Physical activity was assessed using a four question medical questionnaire. Results FTO rs9939609 was genotyped in 1153 elderly Swedish men taking part of a population-based cohort study, the ULSAM cohort. The risk of obesity and differences in BMI according to genotype at the ages of 50, 60, 70, 77 and 82 were investigated. We found no increased risk of obesity and no association with BMI at any age with the FTO rs9939609 variant. We found however interaction between physical activity at the age of 50 years and genotype on BMI levels (p = 0.039 and there was a clear trend towards larger BMI differences between the TT and AA carriers as well as between AT and AA carriers in the less physically active subjects. Conclusion Here we found that the well established obesity risk allele for a common variant in FTO does not associate with increased BMI levels in a Swedish population of adult men which reached adulthood before the appearance of today's obesogenic enviroment. There is an interaction between physical activity and the effect of the FTO genotype on BMI levels suggesting that lack of physical activity is a requirement for an association of FTO gene variants to obesity.

Nuclear waste immobilization in iron phosphate glasses

International Nuclear Information System (INIS)

Garcia, D.A.; Rodriguez, Diego A.; Menghini, Jorge E.; Bevilacqua, Arturo

2007-01-01

Iron-phosphate glasses have become important in the nuclear waste immobilization area because they have some advantages over silicate-based glasses, such as a lower processing temperature and a higher nuclear waste load without losing chemical and mechanical properties. Structure and chemical properties of iron-phosphate glasses are determined in terms of the main components, in this case, phosphate oxide along with the other oxides that are added to improve some of the characteristics of the glasses. For example, Iron oxide improves chemical durability, lead oxide lowers fusion temperature and sodium oxide reduces viscosity at high temperature. In this work a study based on the composition-property relations was made. We used different techniques to characterize a series of iron-lead-phosphate glasses with uranium and aluminium oxide as simulated nuclear waste. We used the Arquimedes method to determine the bulk density, differential temperature analysis (DTA) to determine both glass transition temperature and crystallization temperature, dilatometric analysis to calculate the linear thermal expansion coefficient, chemical durability (MCC-1 test) and X-ray diffraction (XRD). We also applied some theoretic models to calculate activation energies associated with the glass transition temperature and crystallization processes. (author)

The role of early life growth development, the FTO gene and exclusive breastfeeding on child BMI trajectories.

Science.gov (United States)

Wu, Yan Yan; Lye, Stephen; Briollais, Laurent

2017-10-01

Recent studies have implicated the FTO gene in child and adult obesity. A longer duration of exclusive breastfeeding (EXBF) has been shown to reduce body mass index (BMI) and the risk of being overweight in the general population and among FTO gene carriers. However, it remains unclear whether the preventive effect of EXBF could be explained by its impact on early life growth development, e.g. ages at adiposity peak (AP) and adiposity rebound (AR) and BMI velocities in the first years of life, which are major determinants of overweight and obesity later in life. We studied 5590 children from the British Avon Longitudinal Study of Parents and Children (ALSPAC) cohort and modelled their longitudinal BMI profiles with mixed effects models from birth to 16 years of age, as well as their ages at AP, AR and BMI velocities in relation to the FTO gene variant and EXBF. A longer duration of EXBF (i.e. at least 5 months) has substantial impact on BMI growth trajectories among children carrying the FTO adverse variant by modulating the age at AP, age at AR and BMI velocities. EXBF acts antagonistically to the FTO rs9939609 risk allele and by the age of 15, the predicted reduction in BMI after 5 months of EXBF is 0.56 kg/m2 [95% confidence interval (CI) 0.11-1.01; P = 0.003] and 1.14 kg/m2 (95% CI 0.67-1.62; P < 0.0001) in boys and girls, respectively. EXBF influences early life growth development and thus plays a critical role in preventing the risks of overweight and obesity even when those are exacerbated by genetic factors. © The Author 2017; all rights reserved. Published by Oxford University Press on behalf of the International Epidemiological Association

The formation of crystals in glasses containing rare earth oxides

Energy Technology Data Exchange (ETDEWEB)

Fadzil, Syazwani Mohd [Pohang University of Science and Technology (POSTECH), Pohang (Korea, Republic of); Hrma, Pavel [Pohang University of Science and Technology (POSTECH), Pohang, South Korea and Pacific Northwest National Laboratory, Richland, Washington (United States); Crum, Jarrod [Pacific Northwest National Laboratory, Richland, Washington (United States); Siong, Khoo Kok; Ngatiman, Mohammad Fadzlee; Said, Riduan Mt [National University of Malaysia, Bandar Baru Bangi, Selangor (Malaysia)

2014-02-12

Korean spent nuclear fuel will reach the capacity of the available temporary storage by 2016. Pyroprocessing and direct disposal seems to be an alternative way to manage and reuse spent nuclear fuel while avoiding the wet reprocessing technology. Pyroprocessing produces several wastes streams, including metals, salts, and rare earths, which must be converted into stabilized form. A suitable form for rare earth immobilization is borosilicate glass. The borosilicate glass form exhibits excellent durability, allows a high waste loading, and is easy to process. In this work, we combined the rare earths waste of composition (in wt%) 39.2Nd{sub 2}O{sub 3}–22.7CeO{sub 2}–11.7La{sub 2}O{sub 3}–10.9PrO{sub 2}–1.3Eu{sub 2}O{sub 3}–1.3Gd{sub 2}O{sub 3}–8.1Sm{sub 2}O{sub 3}–4.8Y{sub 2}O{sub 3} with a baseline glass of composition 60.2SiO{sub 2}–16.0B{sub 2}O{sub 3}–12.6Na{sub 2}O–3.8Al{sub 2}O{sub 3}–5.7CaO–1.7ZrO{sub 2}. Crystallization in waste glasses occurs as the waste loading increases. It may produce complicate glass processing and affect the product quality. To study crystal formation, we initially made glasses containing 5%, 10% and 15% of La{sub 2}O{sub 3} and then glasses with 5%, 10% and 15% of the complete rare earth mix. Samples were heat-treated for 24 hours at temperatures 800°C to 1150°C in 50°C increments. Quenched samples were analyzed using an optical microscope, scanning electron microscope with energy dispersive spectroscopy, and x-ray diffraction. Stillwellite (LaBSiO{sub 5}) and oxyapatite (Ca{sub 2}La{sub 8}Si{sub 6}O{sub 26}) were found in glasses containing La{sub 2}O{sub 3}, while oxyapatite (Ca{sub 2}La{sub 8}Si{sub 6}O{sub 26} and NaNd{sub 9}Si{sub 6}O{sub 26}) precipitated in glasses with additions of mixed rare earths. The liquidus temperature (T{sub L}) of the glasses containing 5%, 10% and 15% La{sub 2}O{sub 3} were 800°C, 959°C and 986°C, respectively; while T{sub L} was 825°C, 1059°C and 1267°C for glasses

Density of mixed alkali borate glasses: A structural analysis

International Nuclear Information System (INIS)

Doweidar, H.; El-Damrawi, G.M.; Moustafa, Y.M.; Ramadan, R.M.

2005-01-01

Density of mixed alkali borate glasses has been correlated with the glass structure. It is assumed that in such glasses each alkali oxide associates with a proportional quantity of B 2 O 3 . The number of BO 3 and BO 4 units related to each type of alkali oxide depends on the total concentration of alkali oxide. It is concluded that in mixed alkali borate glasses the volumes of structural units related to an alkali ion are the same as in the corresponding binary alkali borate glass. This reveals that each type of alkali oxide forms its own borate matrix and behaves as if not affected with the presence of the other alkali oxide. Similar conclusions are valid for borate glasses with three types of alkali oxide

Optical properties of alkaline earth borate glasses

African Journals Online (AJOL)

user

... devices; radiation shields, surgical lasers and their glass ceramic counter ... Alkaline earth oxides improve glass forming capability while heavy metal ... reports on optical properties of MO-B2O3 glasses containing alkaline earth oxides.

Rare-Earth Oxide Ion (Tm3+, Ho3+, and U3+) Doped Glasses and Fibres for 1.8 to 4 Micrometer Coherent and Broadband Sources

Science.gov (United States)

2006-07-24

oxide ( TeO2 ) , fluorine- containing silicate (SiOF2) and germanate (GeOF2) glass hosts for each dopant by characterising the spectroscopic properties...Earth Oxide Ion (Tm3+, Ho3+, And U3+) Doped Glasses And Fibres For 1.8 To 4 Micrometer Coherent And Broadband Sources 5c. PROGRAM ELEMENT NUMBER 5d...Rare-earth oxide ion (Tm3+, Ho3+, and U3+) doped glasses and fibres for 1.8 to 4 micrometer coherent and broadband sources Report prepared

Sealing glasses for titanium and titanium alloys

Science.gov (United States)

Brow, Richard K.; McCollister, Howard L.; Phifer, Carol C.; Day, Delbert E.

1997-01-01

Barium lanthanoborate sealing-glass compositions are provided comprising various combinations (in terms of mole-%) of boron oxide (B.sub.2 O.sub.3), barium oxide (BaO), lanthanum oxide (La.sub.2 O.sub.3), and at least one other oxide selected from the group consisting of aluminum oxide (Al.sub.2 O.sub.3), calcium oxide (CaO), lithium oxide (Li.sub.2 O), sodium oxide (Na.sub.2 O), silicon dioxide (SiO.sub.2), or titanium dioxide (TiO.sub.2). These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys having an improved aqueous durability and favorable sealing characteristics. Examples of the sealing-glass compositions are provided having coefficients of thermal expansion about that of titanium or titanium alloys, and with sealing temperatures less than about 900.degree. C., and generally about 700.degree.-800.degree. C. The barium lanthanoborate sealing-glass compositions are useful for components and devices requiring prolonged exposure to moisture or water, and for implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps).

Common variants of FTO are associated with childhood obesity in a cross-sectional study of 3,126 urban Indian children.

Directory of Open Access Journals (Sweden)

Om Prakash Dwivedi

Full Text Available FTO variants are robustly associated with obesity and related traits in many population and shown to have variable impact during life course. Although studies have shown association of FTO variants with adiposity in adult Indian, its association in Indian children is yet to be confirmed.Here we examined association of FTO variants (rs9939609 and rs8050136 with obesity and related anthropometric and biochemical traits in 3,126 Indian children (aged 11-17 years including 2,230 normal-weight and 896 over-weight/obese children. We also compared effects observed in the present study with that observed in previous studies on South Asian adults and children of other ethnic groups.The variant rs9939609 showed significant association with risk of obesity [OR = 1.21, P = 2.5 × 10(-3] and its measures BMI, weight, waist circumference and hip circumference [β range = 0.11 to 0.14 Z-score units; P range = 1.3 × 10(-4 to 1.6 × 10(-7] in children. The observed effect sizes in Indian children were similar to those reported for European children. Variant rs9939609 explained 0.88% of BMI variance in Indian children. The effect sizes of rs9939609 on BMI and WC were ~2 fold higher in children than adults. Interestingly rs9939609 was also associated with serum levels of thyroid stimulating hormone (TSH [β = 0.10 Z-score, P = 5.8 × 10(-3]. The other variant rs8050136 was in strong linkage disequilibrium with rs9939609 (r(2 = 0.97 and provided similar association results.The study provides first report of association of FTO variants with obesity and related anthropometric traits in Indian children with higher impact in children compared to adults. We also demonstrated association of FTO variant with serum levels of TSH, indicating putative influence of FTO in hypothalamic-pituitary-thyroid axis.

Enhanced Water Splitting by Fe2O3-TiO2-FTO Photoanode with Modified Energy Band Structure

Directory of Open Access Journals (Sweden)

Eul Noh

2013-01-01

Full Text Available The effect of TiO2 layer applied to the conventional Fe2O3/FTO photoanode to improve the photoelectrochemical performance was assessed from the viewpoint of the microstructure and energy band structure. Regardless of the location of the TiO2 layer in the photoanodes, that is, Fe2O3/TiO2/FTO or TiO2/Fe2O3/FTO, high performance was obtained when α-Fe2O3 and H-TiNT/anatase-TiO2 phases existed in the constituent Fe2O3 and TiO2 layers after optimized heat treatments. The presence of the Fe2O3 nanoparticles with high uniformity in the each layer of the Fe2O3/TiO2/FTO photoanode achieved by a simple dipping process seemed to positively affect the performance improvement by modifying the energy band structure to a more favorable one for efficient electrons transfer. Our current study suggests that the application of the TiO2 interlayer, together with α-Fe2O3 nanoparticles present in the each constituent layers, could significantly contribute to the performance improvement of the conventional Fe2O3 photoanode.

Does the FTO Gene Interact with the Socio‐Economic Status on the Obesity Development Among Young European Children?

DEFF Research Database (Denmark)

Foraita, Ronja; Günther, Frauke; Gwozdz, Wencke

Various twin studies revealed that the influence of genetic factors on psychological diseases or behavior is more expressed in socio‐economically advantaged environments. Other studies predominantly show an inverse relation between socio‐economic status (SES) and childhood obesity in western...... developed countries. The aim of this study is to investigate whether the FTO gene interacts with the socio‐economic status (SES) on childhood obesity in a subsample of the IDEFICS cohort (N=4406). A structural equation model (SEM) is applied with the latent constructs obesity, dietary habits, physical...... activity and fitness habits, and parental SES to estimate the main effects of the latter three variables and a FTO polymorphism on obesity. Further, a multiple group SEM is used to explore whether an interaction effect between the single nucleotide polymorphism rs9939609 within the FTO gene and SES exists...

Morphology, structural and optical properties of iron oxide thin film photoanodes in photoelectrochemical cell: Effect of electrochemical oxidation

Science.gov (United States)

Maabong, Kelebogile; Machatine, Augusto G.; Hu, Yelin; Braun, Artur; Nambala, Fred J.; Diale, Mmantsae

2016-01-01

Hematite (α-Fe2O3) is a promising semiconductor as photoanode in solar hydrogen production from photoelectrolysis of water due to its appropriate band gap, low cost and high electrochemical stability in aqueous caustic electrolytes. Operation of such photoanode in a biased photoelectrochemical cell constitutes an anodization with consequent redox reactions at the electrode surface. α-Fe2O3 thin film photoanodes were prepared by simple and inexpensive dip coating method on fluorine doped tin oxide (FTO) glass substrate, annealed in air at 500 °C for 2 h, then electrochemically oxidized (anodized) in 1 M KOH at 500 mV for 1 min in dark and light conditions. Changes in structural properties and morphology of α-Fe2O3 nanoparticles films were investigated by XRD, Raman spectroscopy and a high resolution FE-SEM. The average grain size was observed to increase from 57 nm for pristine samples to 73 and 77 nm for anodized samples in dark and light respectively. Broadening and red shift in Raman spectra in anodized samples may be attributed to lattice expansion upon oxidation. The UV-visible measurements revealed enhanced absorption in the photoanodes after the treatment. The findings suggest that the anodization of the photoelectrode in a biased cell causes not only changes of the molecular structure at the surface, but also changes in the crystallographic structure which can be detected with x-ray diffractometry.

Morphology, structural and optical properties of iron oxide thin film photoanodes in photoelectrochemical cell: Effect of electrochemical oxidation

International Nuclear Information System (INIS)

Maabong, Kelebogile; Machatine, Augusto G.; Hu, Yelin; Braun, Artur; Nambala, Fred J.; Diale, Mmantsae

2016-01-01

Hematite (α-Fe_2O_3) is a promising semiconductor as photoanode in solar hydrogen production from photoelectrolysis of water due to its appropriate band gap, low cost and high electrochemical stability in aqueous caustic electrolytes. Operation of such photoanode in a biased photoelectrochemical cell constitutes an anodization with consequent redox reactions at the electrode surface. α-Fe_2O_3 thin film photoanodes were prepared by simple and inexpensive dip coating method on fluorine doped tin oxide (FTO) glass substrate, annealed in air at 500 °C for 2 h, then electrochemically oxidized (anodized) in 1 M KOH at 500 mV for 1 min in dark and light conditions. Changes in structural properties and morphology of α-Fe_2O_3 nanoparticles films were investigated by XRD, Raman spectroscopy and a high resolution FE-SEM. The average grain size was observed to increase from ~57 nm for pristine samples to 73 and 77 nm for anodized samples in dark and light respectively. Broadening and red shift in Raman spectra in anodized samples may be attributed to lattice expansion upon oxidation. The UV–visible measurements revealed enhanced absorption in the photoanodes after the treatment. The findings suggest that the anodization of the photoelectrode in a biased cell causes not only changes of the molecular structure at the surface, but also changes in the crystallographic structure which can be detected with x-ray diffractometry.

Morphology, structural and optical properties of iron oxide thin film photoanodes in photoelectrochemical cell: Effect of electrochemical oxidation

Energy Technology Data Exchange (ETDEWEB)

Maabong, Kelebogile [Department of Physics, University of Pretoria, Pretoria 0002 (South Africa); Laboratory of High Ceramics, Empa, Swiss Federal Laboratories for Materials Science and Technology, CH-8600 Dübendorf (Switzerland); Department of Physics, University of Botswana, Private Bag 002, Gaborone (Botswana); Machatine, Augusto G. [Department of Physics, University of Pretoria, Pretoria 0002 (South Africa); Hu, Yelin [Laboratory of High Ceramics, Empa, Swiss Federal Laboratories for Materials Science and Technology, CH-8600 Dübendorf (Switzerland); Laboratory for Photonics and Interfaces, EPFL, Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland); Braun, Artur [Laboratory of High Ceramics, Empa, Swiss Federal Laboratories for Materials Science and Technology, CH-8600 Dübendorf (Switzerland); Nambala, Fred J. [Department of Physics, University of Pretoria, Pretoria 0002 (South Africa); University of Zambia, Box 32379, Great East Road Campus, Lusaka (Zambia); Diale, Mmantsae, E-mail: mmantsae.diale@up.ac.za [Department of Physics, University of Pretoria, Pretoria 0002 (South Africa); Laboratory of High Ceramics, Empa, Swiss Federal Laboratories for Materials Science and Technology, CH-8600 Dübendorf (Switzerland)

2016-01-01

Hematite (α-Fe{sub 2}O{sub 3}) is a promising semiconductor as photoanode in solar hydrogen production from photoelectrolysis of water due to its appropriate band gap, low cost and high electrochemical stability in aqueous caustic electrolytes. Operation of such photoanode in a biased photoelectrochemical cell constitutes an anodization with consequent redox reactions at the electrode surface. α-Fe{sub 2}O{sub 3} thin film photoanodes were prepared by simple and inexpensive dip coating method on fluorine doped tin oxide (FTO) glass substrate, annealed in air at 500 °C for 2 h, then electrochemically oxidized (anodized) in 1 M KOH at 500 mV for 1 min in dark and light conditions. Changes in structural properties and morphology of α-Fe{sub 2}O{sub 3} nanoparticles films were investigated by XRD, Raman spectroscopy and a high resolution FE-SEM. The average grain size was observed to increase from ~57 nm for pristine samples to 73 and 77 nm for anodized samples in dark and light respectively. Broadening and red shift in Raman spectra in anodized samples may be attributed to lattice expansion upon oxidation. The UV–visible measurements revealed enhanced absorption in the photoanodes after the treatment. The findings suggest that the anodization of the photoelectrode in a biased cell causes not only changes of the molecular structure at the surface, but also changes in the crystallographic structure which can be detected with x-ray diffractometry.

Determining optical and radiation characteristics of cathode ray tubes' glass to be reused as radiation shielding glass

International Nuclear Information System (INIS)

Zughbi, A.; Kharita, M.H.; Shehada, A.M.

2017-01-01

A new method of recycling glass of Cathode Ray Tubes (CRTs) has been presented in this paper. The glass from CRTs suggested being used as raw materials for the production of radiation shielding glass. Cathode ray tubes glass contains considerable amounts of environmentally hazardous toxic wastes, namely heavy metal oxides such as lead oxide (PbO). This method makes CRTs glass a favorable choice to be used as raw material for Radiation Shielding Glass and concrete. The heavy metal oxides increase its density, which make this type of glass nearly equivalent to commercially available shielding glass. CRTs glass have been characterized to determine heavy oxides content, density, refractive index, and radiation shielding properties for different Gamma-Ray energies. Empirical methods have been used by using the Gamma-Ray source cobalt-60 and computational method by using the code XCOM. Measured and calculated values were in a good compatibility. The effects of irradiation by gamma rays of cobalt-60 on the optical transparency for each part of the CRTs glass have been studied. The Results had shown that some parts of CRTs glass have more resistant to Gamma radiation than others. The study had shown that the glass of cathode ray tubes could be recycled to be used as radiation shielding glass. This proposed use of CRT glass is only limited to the available quantity of CRT world-wide. - Highlights: • A new method of recycling glass of Cathode Ray Tubes (CRTs) has been presented. • The glass from CRTs used as raw materials for radiation shielding glass. • The resulted glass have good optical properties and stability against radiations.

Infrared and x-ray photoelectron spectroscopic studies on sodium borosilicate glass interacted with thermally oxidized aluminides formed on alloy 690

International Nuclear Information System (INIS)

Yusufali, C.; Dutta, R.S.; Dey, G.K.; Kshirsagar, R.J.; Jagannath; Mishra, R.K.

2012-01-01

Thermally oxidized aluminides formed on Ni-Cr-Fe based superalloy 690 substrates were subjected to interaction with sodium borosilicate melt (used as matrices for immobilization of high-level radioactive liquid waste) at 1248 K for 192 hours. After the interaction, Fourier-transform infrared (FT-IR) spectroscopy analysis of glass samples indicated the incorporation of Al in the glass network. X-ray photoelectron spectroscopy (XPS) of glass specimens revealed modified glass structure. (author)

Interactions between the FTO and GNB3 genes contribute to varied clinical phenotypes in hypertension.

Directory of Open Access Journals (Sweden)

Rahul Kumar

Full Text Available The genes FTO and GNB3 are implicated in essential hypertension but their interaction remains to be explored. This study investigates the role of interaction between the two genes in the pathophysiology of essential hypertension.In a case-control study comprising 750 controls and 550 patients, interaction between the polymorphisms of FTO and GNB3 was examined using multifactor dimensionality reduction (MDR. The influence of interaction on clinical phenotypes like systolic and diastolic blood pressure, mean arterial pressure and body mass index was also investigated. The 3-locus MDR model comprising FTO rs8050136C/A and GNB3 rs1129649T/C and rs5443C/T emerged as the best disease conferring model. Moreover, the interacted-genotypes having either 1, 2, 3, 4 or 5 risk alleles correlated with linearly increasing odds ratios of 1.91 (P = 0.027; 3.93 (P = 2.08E-06; 4.51 (P = 7.63E-07; 7.44 (P = 3.66E-08 and 11.57 (P = 1.18E-05, respectively, when compared with interacted-genotypes devoid of risk alleles. Furthermore, interactions among haplotypes of FTO (H1-9 and GNB3 (Ha-d differed by >1.5-fold for protective-haplotypes, CTGGC+TC [H2+Ha] and CTGAC+TC [H4+Ha] (OR = 0.39, P = 0.003; OR = 0.22, P = 6.86E-05, respectively and risk-haplotypes, AAAGC+CT [H3+Hc] and AAAGC+TT [H3+Hd] (OR = 2.91, P = 9.98E-06; OR = 2.50, P = 0.004, respectively compared to individual haplotypes. Moreover, the effectiveness of gene-gene interaction was further corroborated with a 1.29-, 1.25- and 1.38-fold higher SBP, MAP and BMI, respectively, in patients having risk interacted-haplotype H3+Hc and 2.48-fold higher SBP having risk interacted-haplotype H3+Hd compared to individual haplotypes.Interactions between genetic variants of FTO and GNB3 influence clinical parameters to augment hypertension.

Comparative study on the change in index of refraction in ion-exchange interdiffusion in alkali-silicate glasses containing calcium, strontium, barium and titanium oxides

International Nuclear Information System (INIS)

Livshits, V.Ya.; Marchuk, E.A.

1993-01-01

Different ability to ion exchange from the salts of lithium-sodium-silicate glass melt containing calcium (or strontium, or barium) and titanium oxides in addition has been shown. CaO, SrO and BaO have negative effect, but TiO 2 -positive one on the fullness of ion exchange of lithium-sodium and on the rate of interdiffusion in alkali-silicate glass. The value of change in index of refraction of glass with TiO 2 is twice higher than glass with calcium oxide (or strontium, or barium) as the fourth component

Professionalisering van het FTO in Noord-Holland Noord: evaluatie van een pilot.

NARCIS (Netherlands)

Jansen, J.; Dijk, L. van; Wagner, C.; Bakker, D. de

2004-01-01

Voor een succesvol Farmaco Therapie Overleg (FTO) zijn een goede voorbereiding, een strenge voorzitter, een duidelijk afgebakend onderwerp en heldere afspraken nodig. Daarmee is het mogelijk het functioneren van zo'n overleg naar een (nog) hoger niveau te tillen. Dit blijkt uit een

Macronutrient-specific effect of FTO rs9939609 in response to a 10-week randomized hypo-energetic diet among obese Europeans

DEFF Research Database (Denmark)

Grau, K; Hansen, T; Holst, C

2009-01-01

-energetic diet (measured resting metabolic rate multiplied by 1.3-600 kcal day(-1)). Body weight, fat mass (FM), fat-free mass (FFM), waist circumference (WC), resting energy expenditure (REE), fasting fat oxidation as % of REE (FatOx), insulin release (HOMA-beta) and a surrogate measure of insulin resistance...... found no effect of FTO rs9939609 genotype on Deltaweight, DeltaFM, DeltaFFM, DeltaWC or DeltaFatOx. However, participants with TT had a smaller reduction in REE on LF than on HF diet (75 kcal/24 h; interaction: P=0.0055). These individuals also showed the greatest reduction in HOMA-beta and HOMA...

Electrophoretic deposition (EPD) of multi-walled carbon nano tubes (MWCNT) onto indium-tin-oxide (ITO) glass substrates

International Nuclear Information System (INIS)

Mohd Roslie Ali; Shahrul Nizam Mohd Salleh

2009-01-01

Full text: Multi-Walled Carbon Nano tubes (MWCNT) were deposited onto Indium-Tin-Oxide (ITO)-coated glass substrates by introducing the use of Electrophoretic Deposition (EPD) as the method. The Multi-Walled Carbon Nano tubes (MWCNT) were dispersed ultrasonically in ethanol and sodium hydroxide (NaOH) to form stable suspension. The addition of Sodium Hydroxide in ethanol can stabilize the suspension, which was very important step before the deposition take place. Two substrates of Indium-Tin-Oxide(ITO)-coated glass placed in parallel facing each other (conductive side) into the suspension. The deposition occurs at room temperature, which the distance fixed at 1 cm between both electrodes and the voltage level applied was fixed at 400 V, respectively. The deposition time also was fixed at 30 minutes. The deposited ITO-Glass with Multi-Walled Carbon Nano tubes (MWCNT) will be characterized using Scanning Electron Microscope (SEM), Atomic Force Microscope (AFM), and Raman Microscope. The images of SEM shows that the Multi -Walled Carbon Nano tubes (MWCNT) were distributed uniformly onto the surface of ITO-Glass. The deposited ITO-Glass with Multi-Walled Carbon Nano tubes (MWCNT) could be the potential material in various practical applications such as field emission devices, fuel cells, and super capacitors. Electrophoretic deposition (EPD) technique was found to be an efficient technique in forming well distribution of Multi-Walled Carbon Nano tubes (MWCNT) onto ITO-Glass substrates, as proved in characterization methods, in which the optimum conditions will play the major role. (author)

Structural, morphological and optical studies of F doped SnO2 thin films

Science.gov (United States)

Chandel, Tarun; Thakur, Vikas; Dwivedi, Shailendra Kumar; Zaman, M. Burhanuz; Rajaram, Poolla

2018-05-01

Highly conducting and transparent FTO (flourine doped tin Oxide) thin films were grown on the glass substrates using a low cost spray pyrolysis technique. The films were characterized for their structural, morphological and optical studies using XRD, SEM and UV-Vis spectroscopy. XRD studies show that the FTO films crystallize in Tetragonal cassiterite structure. Morphological analysis using SEM show that the films are uniformly covered with spherical grains albeit high in surface roughness. The average optical transmission greater than 80% in the visible region along with the appearance of interference fringes in the transmission curves confirms the high quality of the films. Electrical studies show that the films exhibit sheet resistance below 10 Ω ϒ-1.

The obesity-associated polymorphisms FTO rs9939609 and MC4R rs17782313 and endometrial cancer risk in non-Hispanic white women.

Directory of Open Access Journals (Sweden)

Galina Lurie

2011-02-01

Full Text Available Overweight and obesity are strongly associated with endometrial cancer. Several independent genome-wide association studies recently identified two common polymorphisms, FTO rs9939609 and MC4R rs17782313, that are linked to increased body weight and obesity. We examined the association of FTO rs9939609 and MC4R rs17782313 with endometrial cancer risk in a pooled analysis of nine case-control studies within the Epidemiology of Endometrial Cancer Consortium (E2C2. This analysis included 3601 non-Hispanic white women with histologically-confirmed endometrial carcinoma and 5275 frequency-matched controls. Unconditional logistic regression models were used to assess the relation of FTO rs9939609 and MC4R rs17782313 genotypes to the risk of endometrial cancer. Among control women, both the FTO rs9939609 A and MC4R rs17782313 C alleles were associated with a 16% increased risk of being overweight (p = 0.001 and p = 0.004, respectively. In case-control analyses, carriers of the FTO rs9939609 AA genotype were at increased risk of endometrial carcinoma compared to women with the TT genotype [odds ratio (OR  = 1.17; 95% confidence interval (CI: 1.03-1.32, p = 0.01]. However, this association was no longer apparent after adjusting for body mass index (BMI, suggesting mediation of the gene-disease effect through body weight. The MC4R rs17782313 polymorphism was not related to endometrial cancer risk (per allele OR = 0.98; 95% CI: 0.91-1.06; p = 0.68. FTO rs9939609 is a susceptibility marker for white non-Hispanic women at higher risk of endometrial cancer. Although FTO rs9939609 alone might have limited clinical or public health significance for identifying women at high risk for endometrial cancer beyond that of excess body weight, further investigation of obesity-related genetic markers might help to identify the pathways that influence endometrial carcinogenesis.

A statistical approach to determine the effects of nuclear glass components on the short and long term glass alteration

International Nuclear Information System (INIS)

Advocat, Th.; Tovena, I.; Vernaz, E.; Larche, F.; Phan Tan Luu, R.

1997-01-01

The experimentation plan methodology may be a powerful tool to design statistical models able to calculate quantitative leach rates as a function of glass compositions. The investigation discussed here implemented an experimentation plan methodology covering a wide range of glass composition variations with two major objectives: - identify the effects of the main component oxides of R7T7 glass (SiO 2 , B 2 O 3 , Al 2 O 3 , Na 2 O+Li 2 O, additive oxides, Fission Products oxides, actinide oxides) on the dissolution rates far and close to equilibrium; - and develop a statistical model relating the measured initial dissolution rate with the selected oxide compositions. A second-degree silica-based model was developed to express the initial dissolution rates at 100 deg C according to the oxide weight percentage of 6 major oxides or oxide groups. The model is qualified by comparison with independent experimental results. For the short term, far from saturation conditions (confined media), plotting the effects of the oxides clearly showed that SiO 2 , Al 2 O 3 and the additive oxides enhanced glass durability at 100 deg C, while B 2 O 3 and Na 2 O+Li 2 O diminished the initial corrosion resistance. For the long term, plotting the effects of the oxides showed that additive oxides, Al 2 O 3 and SiO 2 enhanced glass durability at 90 deg C, in that order, while Na 2 O+Li 2 O still diminished the corrosion resistance. The fission products and actinide oxides and ZrO 2 have apparently a slight beneficial effect on the glass durability, under saturation conditions (long term). (author)

Minimizing energy losses in perovskite solar cells using plasma-treated transparent conducting layers

Energy Technology Data Exchange (ETDEWEB)

Dao, Van-Duong [Department of Chemical Engineering, Chungnam National University, Yuseong-Gu, Daejeon 305-764 (Korea, Republic of); Larina, Liudmila L. [Department of Chemical Engineering, Chungnam National University, Yuseong-Gu, Daejeon 305-764 (Korea, Republic of); Department of Solar Photovoltaics, Institute of Biochemical Physics, Russian Academy of Sciences, 119334 Moscow (Russian Federation); Choi, Ho-Suk, E-mail: hchoi@cnu.ac.kr [Department of Chemical Engineering, Chungnam National University, Yuseong-Gu, Daejeon 305-764 (Korea, Republic of)

2015-10-30

This study reports for increasing the efficiency of perovskite solar cells (PSCs) by modifying the surface of a fluorine-doped indium tin oxide (FTO) substrate using an atmospheric pressure plasma treatment. Surface modification of the FTO film involved several challenges, such as control of the blocking layer uniformity, removal of pinholes, and deposition of a dense layer. This strategy allows the suppression of charge recombination at the interface between the FTO substrate and hole conductor. Electrochemical impedance spectroscopy analysis showed that the plasma treatment increased the charge transfer resistance between the FTO and hole conductor from 95.1 to 351.1 Ω, indicating enhanced resistance to the electron back reaction. Analyses of the open-circuit photovoltage decay revealed that modification of the surface of the FTO substrate by plasma treatment increased time constant from 6.44 ms to 13.15 ms. The effect is ascribed to suppression of the electron recombination rate. PSCs based on the newly developed electrode had 39% higher efficiency than reference devices. The obtained results provide direct evidence in favor of the developed strategy. - Highlights: • Plasma treatment of FTO glass effectively increases the efficiency of PSCs. • The surface becomes superhydrophilic after plasma treatment. • The superhydrophilic surface provides uniform and pinhole-free coverage of TiO{sub 2} BL. • The transmittance of the plasma-treated FTO/BL is higher than the pristine FTO/BL. • The electron recombination is reduced due to its high quality of TiO{sub 2} BL.

The Synthesis of NiO/TiO2 Heterostructures and Their Valence Band Offset Determination

Directory of Open Access Journals (Sweden)

Z. H. Ibupoto

2014-01-01

Full Text Available In this work, a heterojunction based on p-type NiO/n-type TiO2 nanostructures has been prepared on the fluorine doped tin oxide (FTO glass substrate by hydrothermal method. Scanning electron microscopy (SEM and X-Ray diffraction techniques were used for the morphological and crystalline arrays characterization. The X-ray photoelectron spectroscopy was employed to determine the valence-band offset (VBO of the NiO/TiO2 heterojunction prepared on FTO glass substrate. The core levels of Ni 2p and Ti 2p were utilized to align the valence-band offset of p-type NiO/n-type TiO2 heterojunction. The valence band offset was found to be ∼0.41 eV and the conduction band was calculated about ∼0.91 eV. The ratio of conduction band offset and the valence-band offset was found to be 2.21.

Poly(3,3-dibenzyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine/Platinum Composite Films as Potential Counter Electrodes for Dye-Sensitized Solar Cells

Directory of Open Access Journals (Sweden)

Jung-Chuan Chou

2017-07-01

Full Text Available In this study, poly(3,3-dibenzyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine/platinum composite films (PProDOT-Bz2/Pt were used as counter electrodes (CEs in dye-sensitized solar cells (DSSCs. The composite films were prepared on fluorine-doped tin oxide (FTO glass by radio frequency (RF sputtering to deposit platinum (Pt for 30 s. Afterwards, PProDOT-Bz2 was deposited on the Pt–FTO glass via electrochemical polymerization. The electron transfer process of DSSCs was investigated using electrochemical impedance spectroscopy (EIS and cyclic voltammetry (CV. The DSSCs with 0.05 C/cm2 PProDOT-Bz2-Pt composite films showed an open circuit voltage (Voc of 0.70 V, a short-circuit current density (Jsc of 7.27 mA/cm2, and a fill factor (F.F. of 68.74%. This corresponded to a photovoltaic conversion efficiency (η of 3.50% under a light intensity of 100 mW/cm2.

Thin copolymer-cased light-emitting display made with fluorine-foped tin oxide substrates

Directory of Open Access Journals (Sweden)

Lessmann Rudolf

2004-01-01

Full Text Available Seven-segment displays are used to show numerical quantities in electronic equipment, being present in most of the low-end electronics. In this work we describe a novel organic light emitting display made with poly(1,10 decanedioxy 2 methoxy - 1,2 phenylene - 1,2 ethenylene - 3,6 dimethoxy - 1,4 phenylene - 1,2 ethenylene 3 methoxy - 1,4 - phenylene (OPPVDBC, tris(8-hydroxyquinolinealuminum salt (Alq3 and a hole injection layer (PEDOT:PSS: poly(3,4 - ethylenedioxythiophene : poly(styrenesulfonate. The general device structure is FTO/PEDOT:PSS/OPPVDBC/Ca/Al or FTO/PEDOT:PSS/OPPVDBC/Alq3/Ca/Al. The FTO (fluorine-doped tin oxide thin films are transparent (transmittance > 80 % in the visible region of the spectrum, conductive (< 15 omega/º for 200 nm thick films, and present high chemical stability.

The Photocatalytic Activity and Compact Layer Characteristics of TiO2 Films Prepared Using Radio Frequency Magnetron Sputtering

Directory of Open Access Journals (Sweden)

H. C. Chang

2014-01-01

Full Text Available TiO2 compact layers are used in dye-sensitized solar cells (DSSCs to prevent charge recombination between the electrolyte and the transparent conductive substrate (indium tin oxide, ITO; fluorine-doped tin oxide, FTO. Thin TiO2 compact layers are deposited onto ITO/glass by means of radio frequency (rf magnetron sputtering, using deposition parameters that ensure greater photocatalytic activity and increased DSSC conversion efficiency. The photoinduced decomposition of methylene blue (MB and the photoinduced hydrophilicity of the TiO2 thin films are also investigated. The photocatalytic performance characteristics for the deposition of TiO2 films are improved by using the Grey-Taguchi method. The average transmittance in the visible region exceeds 85% for all samples. The XRD patterns of the TiO2 films, for sol-gel with spin coating of porous TiO2/TiO2 compact/ITO/glass, show a good crystalline structure. In contrast, without the TiO2 compact layer (only porous TiO2, the peak intensity of the anatase (101 plane in the XRD patterns for the TiO2 film has a lower value, which demonstrates inferior crystalline quality. With a TiO2 compact layer to prevent charge recombination, a higher short-circuit current density is obtained. The DSSC with the FTO/glass and Pt counter electrode demonstrates the energy conversion efficiency increased.

The Association of FTO SNP rs9939609 with Weight Gain at University

NARCIS (Netherlands)

Meisel, S.F.; Beeken, R.J.; Jaarsveld, C.H.M. van; Wardle, J.

2015-01-01

AIM: We tested the hypothesis that the obesity-associated FTO SNP rs9939609 would be associated with clinically significant weight gain (>/= 5% of initial body weight) in the first year of university; a time identified as high risk for weight gain. METHODS: We collected anthropometric data from

BNFL Report Glass Formers Characterization

Energy Technology Data Exchange (ETDEWEB)

Schumacher, R.F.

2000-07-27

The objective of this task was to obtain powder property data on candidate glass former materials, sufficient to guide conceptual design and estimate the cost of glass former handling facilities as requested under Part B1 of BNFL Technical and Development Support. Twenty-nine glass forming materials were selected and obtained from vendors for the characterization of their physical properties, durability in caustic solution, and powder flow characteristics. A glass former was selected based on the characterization for each of the ten oxide classes required for Envelope A, B, and C mixtures. Three blends (A, B, and C) were prepared based on formulations provided by Vitreous State Laboratory and evaluated with the same methods employed for the glass formers. The properties obtained are presented in a series of attached Tables. It was determined that five of the ten glass formers, (kyanite, iron oxide, titania, zircon, and zinc oxide) have the potential to cause some level of solids f low problems. The problems might include arching or ratholing in the silo/hopper. In addition, all of the blends may require consideration for their handling.

BNFL Report Glass Formers Characterization

International Nuclear Information System (INIS)

Schumacher, R.F.

2000-01-01

The objective of this task was to obtain powder property data on candidate glass former materials, sufficient to guide conceptual design and estimate the cost of glass former handling facilities as requested under Part B1 of BNFL Technical and Development Support. Twenty-nine glass forming materials were selected and obtained from vendors for the characterization of their physical properties, durability in caustic solution, and powder flow characteristics. A glass former was selected based on the characterization for each of the ten oxide classes required for Envelope A, B, and C mixtures. Three blends (A, B, and C) were prepared based on formulations provided by Vitreous State Laboratory and evaluated with the same methods employed for the glass formers. The properties obtained are presented in a series of attached Tables. It was determined that five of the ten glass formers, (kyanite, iron oxide, titania, zircon, and zinc oxide) have the potential to cause some level of solids f low problems. The problems might include arching or ratholing in the silo/hopper. In addition, all of the blends may require consideration for their handling

Transparent solar antenna of 28 GHz using transparent conductive oxides (TCO) thin film

International Nuclear Information System (INIS)

Mohd Ali, N I; Misran, N; Mansor, M F; Jamlos, M F

2017-01-01

This paper presents the analysis of 28GHz solar patch antenna using the variations of transparent conductive oxides (TCO) thin film as the radiating patch. Solar antenna is basically combining the function of antenna and solar cell into one device and helps to maximize the usage of surface area. The main problem of the existing solar antenna is the radiating patch which made of nontransparent material, such as copper, shadowing the solar cell and degrades the total solar efficiency. Hence, by using the transparent conductive oxides (TCO) thin film as the radiating patch, this problem can be tackled. The TCO thin film used is varied to ITO, FTO, AgHT-4, and AgHT-8 along with glass as substrate. The simulation of the antenna executed by using Computer Simulation Technology (CST) Microwave Studio software demonstrated at 28 GHz operating frequency for 5G band applications. The performance of the transparent antennas is compared with each other and also with the nontransparent patch antenna that using Rogers RT5880 as substrate, operating at the same resonance frequency and then, the material that gives the best performance is identified. (paper)

Transparent solar antenna of 28 GHz using transparent conductive oxides (TCO) thin film

Science.gov (United States)

Ali, N. I. Mohd; Misran, N.; Mansor, M. F.; Jamlos, M. F.

2017-05-01

This paper presents the analysis of 28GHz solar patch antenna using the variations of transparent conductive oxides (TCO) thin film as the radiating patch. Solar antenna is basically combining the function of antenna and solar cell into one device and helps to maximize the usage of surface area. The main problem of the existing solar antenna is the radiating patch which made of nontransparent material, such as copper, shadowing the solar cell and degrades the total solar efficiency. Hence, by using the transparent conductive oxides (TCO) thin film as the radiating patch, this problem can be tackled. The TCO thin film used is varied to ITO, FTO, AgHT-4, and AgHT-8 along with glass as substrate. The simulation of the antenna executed by using Computer Simulation Technology (CST) Microwave Studio software demonstrated at 28 GHz operating frequency for 5G band applications. The performance of the transparent antennas is compared with each other and also with the nontransparent patch antenna that using Rogers RT5880 as substrate, operating at the same resonance frequency and then, the material that gives the best performance is identified.

A statistical approach to determine the effects of nuclear glass components on the short and long term glass alteration

Energy Technology Data Exchange (ETDEWEB)

Advocat, Th; Tovena, I; Vernaz, E [CEA Valrho, Dir. de l' Energie Nucleaire, DEN, 30 - Marcoule (France); Larche, F [Montpellier-2 Univ., 34 (France); Phan Tan Luu, R [Faculte de St Jerome, 13 - Marseille (France)

1997-07-01

The experimentation plan methodology may be a powerful tool to design statistical models able to calculate quantitative leach rates as a function of glass compositions. The investigation discussed here implemented an experimentation plan methodology covering a wide range of glass composition variations with two major objectives: - identify the effects of the main component oxides of R7T7 glass (SiO{sub 2}, B{sub 2}O{sub 3}, Al{sub 2}O{sub 3}, Na{sub 2}O+Li{sub 2}O, additive oxides, Fission Products oxides, actinide oxides) on the dissolution rates far and close to equilibrium; - and develop a statistical model relating the measured initial dissolution rate with the selected oxide compositions. A second-degree silica-based model was developed to express the initial dissolution rates at 100 deg C according to the oxide weight percentage of 6 major oxides or oxide groups. The model is qualified by comparison with independent experimental results. For the short term, far from saturation conditions (confined media), plotting the effects of the oxides clearly showed that SiO{sub 2}, Al{sub 2}O{sub 3} and the additive oxides enhanced glass durability at 100 deg C, while B{sub 2}O{sub 3} and Na{sub 2}O+Li{sub 2}O diminished the initial corrosion resistance. For the long term, plotting the effects of the oxides showed that additive oxides, Al{sub 2}O{sub 3} and SiO{sub 2} enhanced glass durability at 90 deg C, in that order, while Na{sub 2}O+Li{sub 2}O still diminished the corrosion resistance. The fission products and actinide oxides and ZrO{sub 2} have apparently a slight beneficial effect on the glass durability, under saturation conditions (long term). (author)

High-energy X-ray diffraction studies of short- and intermediate-range structure in oxide glasses

International Nuclear Information System (INIS)

Suzuya, Kentaro

2002-01-01

The feature of high-energy X-ray diffraction method is explained. The oxide glasses studies by using BL04B2, high-energy X-ray diffraction beam line of SPring-8, and the random system materials by high-energy monochromatic X-ray diffraction are introduced. An advantage of third generation synchrotron radiation is summarized. On SPring-8, the high-energy X-ray diffraction experiments of random system are carried out by BL04B2 and BL14B1 beam line. BL04B2 can select Si (111)(E=37.8 keV, λ=0.033 nm) and Si(220)(E=61.7 keV, λ=0.020 nm) as Si monochromator. The intermediate-range structure of (MgO) x (P 2 O 5 ) 1-x glass ,MgP 2 O 6 glass, B 2 O 3 glass, SiO 2 and GeO 2 are explained in detail. The future and application of high-energy X-ray diffraction are stated. (S.Y.)

Obtención de columnas de ZnO. Variables a controlar (y II)

OpenAIRE

Marí, B.; Cembrero, J.; Mollar, M.; Pascual, M.; Perales, M.

2006-01-01

The growth process via electrodeposition technique, of zinc oxide (ZnO) columns, on a glass substrate coated with conductor tin oxide and fluorine (FTO), is analysed. An exponential law of columns growth is determined to relate the columns height with exposition time in electrolytic mean. The columns growing is governed by an exponential law for electrolytic exposition times under 103 s, with constant temperature (65±2 ºC) and current density (i = 2,5 mA/ cm2); for exposition times larger tha...

High-Level Waste Glass Formulation Model Sensitivity Study 2009 Glass Formulation Model Versus 1996 Glass Formulation Model

International Nuclear Information System (INIS)

Belsher, J.D.; Meinert, F.L.

2009-01-01

This document presents the differences between two HLW glass formulation models (GFM): The 1996 GFM and 2009 GFM. A glass formulation model is a collection of glass property correlations and associated limits, as well as model validity and solubility constraints; it uses the pretreated HLW feed composition to predict the amount and composition of glass forming additives necessary to produce acceptable HLW glass. The 2009 GFM presented in this report was constructed as a nonlinear optimization calculation based on updated glass property data and solubility limits described in PNNL-18501 (2009). Key mission drivers such as the total mass of HLW glass and waste oxide loading are compared between the two glass formulation models. In addition, a sensitivity study was performed within the 2009 GFM to determine the effect of relaxing various constraints on the predicted mass of the HLW glass.

The effects of uranium oxide high-level waste on the structure of iron phosphate glasses

International Nuclear Information System (INIS)

Badyal, Y.

1998-01-01

Because of their unusually good chemical durability, iron phosphate glasses are a natural candidate for a nuclear waste disposal glass. We have studied the effects of UO 2 high-level waste on the structure of iron phosphate glasses with both neutron and high-energy x-ray diffraction using the GLAD instrument of the Intense Pulsed Neutron Source and the 1-BM bending magnet beamline of the Advanced Photon Source, respectively. The results of neutron scattering, which is mostly sensitive to correlations involving light atoms i.e. O-O, Fe-O and P-O, suggest the main structural features of the base glass are largely unaffected by the addition of UO 2 . The nearest-neighbor P-O, Fe-O and O-O peaks remain at the same position in real space and their intensities scale approximately with concentration. These findings are consistent with the earlier results of Raman scattering and EXAFS on the Fe-K edge wherein both cases the spectra remain similar to the base glass. High-energy x-ray scattering which is sensitive to correlations involving the heavier atoms and thus complements the neutron measurements, is also consistent with uranium occupying interstitial sites in the relatively undisturbed base glass structure. However, important questions remain as to the precise local structure and oxidation state of uranium in these glasses

Polymorphism of the FTO Gene Influences Body Weight in Children with Type 1 Diabetes without Severe Obesity

OpenAIRE

Łuczyński, Włodzimierz; Fendler, Wojciech; Ramatowska, Anna; Szypowska, Agnieszka; Szadkowska, Agnieszka; Młynarski, Wojciech; Chumiecki, Miron; Jarosz-Chobot, Przemysława; Chrzanowska, Joanna; Noczyńska, Anna; Brandt, Agnieszka; Myśliwiec, Małgorzata; Głowińska-Olszewska, Barbara; Bernatowicz, Paweł; Kowalczuk, Oksana

2014-01-01

The objective was to compare the impact of clinical and genetic factors on body mass index (BMI) in children with type 1 diabetes (T1DM) without severe obesity. A total of 1,119 children with T1DM (aged 4–18 years) were qualified to take part in the study. All children were genotyped for variants of FTO, MC4R, INSIG2, FASN, NPC1, PTER, SIRT1, MAF, IRT1, and CD36. Results. Variants of FTO showed significant association with BMI-SDS in the T1DM group. The main factors influencing BMI-SDS in chi...

Preparation and Characterization of Carbon Nano tube-based Electrochromic Material

International Nuclear Information System (INIS)

Muhammad Shahazmi Mohd Zambri; Norani Muti Mohamed; Kait, C.F.

2011-01-01

Electrochromic materials that can change their optical properties reversibly for an applied potential due to electrochemical oxidation and reduction have been used in various applications of electrochromic windows or smart glass. Conducting polymer like poly aniline (PANI) is one of the most promising electrochromic materials because of its ease of synthesis and environmental stability. However, the electrochemically deposited poly aniline exhibit substantial resistivity which is attributed to the lack of conducting pathways at the nano scale associated with random deposition morphology. This paper describes the study in developing electrochromic material that will exhibit higher conductivity by using carbon nano tubes (CNTs) as the filler. Preparation of electrochromic material on ITO and FTO glass substrate was done by electrochemical process using mixture of CNTs and PANI in H 2 SO 4 at several loading of CNTs, voltage applied and duration of the process. PANI and PANI/ CNTs films produced were then characterized using SEM and Hall Effect measurement. From the study, highly conductive PANI/ CNTs film can be obtained by using optimum condition of the process parameters. PANI film deposited on FTO glass substrate was also found to be of good quality with conductivity two orders of magnitude higher than the film deposited on ITO glass substrate. (author)

Role of groundwater oxidation potential and radiolysis on waste glass performance in crystalline repository environments

International Nuclear Information System (INIS)

Jantzen, C.M.; Bibler, N.E.

1985-01-01

Laboratory experiments have shown that groundwater conditions in a Stripa granite repository will be as reducing as those in a basalt repository. The final oxidation potential (Eh) at 70 0 C for Stripa groundwater deaerated and equilibrated with crystalline granite was -0.45V. In contrast, the oxidation potential at 60 0 C for Grande Ronde groundwater equilibrated with basalt was -0.40V. The reducing groundwater conditions were found to slightly decrease the time-dependent release of soluble components from the waste glass. Spectrophotometric analysis of the equilibrated groundwaters indicated the presence of Fe 2+ confirming that the Fe 2+ /Fe 3+ couple is controlling the oxidation potential. It was also shown that in the alkaline pH regime of these groundwaters the iron species are primarily associated with x-ray amorphous precipitates in the groundwater. Gamma radiolysis in the absence of waste glass and in the absence of oxygen further reduces the oxidation potential of both granitic and basaltic groundwaters. The effect is more pronounced in the basaltic groundwater. The mechanism for this decrease is under investigation but appears related to the reactive amorphous precipitate. The results of these tests suggest that H 2 may not escape from the repository system as postulated and that radiolysis may not cause the groundwaters to become oxidizing in a crystalline repository when abundant Fe 2+ species are present. 23 refs., 3 figs., 3 tabs

Effect of incorporation of zinc oxide nanoparticles on mechanical properties of conventional glass ionomer cements.

Science.gov (United States)

Panahandeh, Narges; Torabzadeh, Hassan; Aghaee, Mohammadamin; Hasani, Elham; Safa, Saeed

2018-01-01

The aim of this study is to investigate the physical properties of conventional and resin-modified glass ionomer cements (GICs) compared to GICs supplemented with zinc oxide (ZnO) nanofiller particles at 5% (w/w). In this in vitro study, ZnO nanoparticles of different morphologies (nanospherical, nanorod, and nanoflower) were incorporated to glass ionomer powder. The samples were subjected to the flexural strength ( n = 20) and surface hardness test ( n = 12) using a universal testing machine and a Vickers hardness machine, respectively. Surface analysis and crystal structure of samples were performed with scanning electron microscope and X-radiation diffraction, respectively. The data were analyzed using one-way ANOVA, Shapiro-Wilk, and Tukey's tests ( P glass ionomer containing nanoparticles was not significantly different from the control group ( P > 0.05). The surface hardness of the glass ionomer containing nanospherical or nanoflower ZnO was significantly lower than the control group ( P glass ionomer containing nanorod ZnO was not significantly different from the control group ( P = 0.868). Incorporation of nanospherical and nanoflower ZnO to glass ionomer decreased their surface hardness, without any changes on their flexural strength. Incorporation of nanorod ZnO particles caused no effect on the mechanical properties.

Crystallization of copper metaphosphate glass

Science.gov (United States)

Bae, Byeong-Soo; Weinberg, Michael C.

1993-01-01

The effect of the valence state of copper in copper metaphosphate glass on the crystallization behavior and glass transition temperature has been investigated. The crystallization of copper metaphosphate is initiated from the surface and its main crystalline phase is copper metaphosphate (Cu(PO)3),independent of the (Cu sup 2+)/(Cu(total)). However, the crystal morphology, the relative crystallization rates, and their temperature dependences are affected by the (Cu sup 2+)/(Cu (total)) ratio in the glass. On the other hand, the totally oxidized glass crystallizes from all over the surface. The relative crystallization rate of the reduced glass to the totally oxidized glass is large at low temperature, but small at high temperature. The glass transition temperature of the glass increases as the (Cu sup 2+)/(Cu(total)) ratio is raised. It is also found that the atmosphere used during heat treatment does not influence the crystallization of the reduced glass, except for the formation of a very thin CuO surface layer when heated in air.

Hysteresis losses in iron oxide nanoparticles prepared by glass crystallization or wet chemical precipitation

International Nuclear Information System (INIS)

Mueller, Robert; Dutz, Silvio; Hergt, Rudolf; Schmidt, Christopher; Steinmetz, Hanna; Zeisberger, Matthias; Gawalek, Wolfgang

2007-01-01

Ferrofluids were prepared from glass crystallized as well as wet precipitated iron oxide particles. Comparing hysteresis losses versus applied field amplitude from particles in immobilized state (powder) and in fluid state (ferrofluid) shows in some cases anomalous large losses at low magnetic fields. The influence of texture on the losses was investigated

Production and remediation of low-sludge, simulated Purex waste glasses, 1: Effects of sludge oxide additions on melter operation

International Nuclear Information System (INIS)

Ramsey, W.G.

1993-01-01

Glass produced during the Purex 4 campaigns of the Integrated Defense Waste Processing Facility (DWPF) Melter System (IDMS) and the 774 Research Melter contained a lower fraction of sludge components than targeted by the Product Composition Control System (PCCS). Purex 4 glass was more durable than the benchmark (EA) glass, but less durable than most simulated SRS high-level waste glasses. Also, Purex 4 glass was considerably less durable than predicted by the algorithm which will be used to control production of DWPF glass. A melter run was performed using the 774 Research Melter to determine if the initial PCCS target composition determined for Purex 4 would produce acceptable glass whose durability could be accurately modeled by Hydration Thermodynamics. Reagent grade oxides and carbonates were added to Purex 4 melter feed stock to simulate a higher sludge loading. Each canister of glass produced was sampled and the composition, crystallinity, and durability was determined. This document details the melter operation and composition and crystallinity analyses

Gamma-ray mass attenuation coefficient and half value layer factor of some oxide glass shielding materials

International Nuclear Information System (INIS)

Waly, El-Sayed A.; Fusco, Michael A.; Bourham, Mohamed A.

2016-01-01

The variation in dosimetric parameters such as mass attenuation coefficient, half value layer factor, exposure buildup factor, and the photon mean free path for different oxide glasses for the incident gamma energy range 0.015–15 MeV has been studied using MicroShield code. It has been inferred that the addition of PbO and Bi 2 O 3 improves the gamma ray shielding properties. Thus, the effect of chemical composition on these parameters is investigated in the form of six different glass compositions, which are compared with specialty concrete for nuclear radiation shielding. The composition termed ‘Glass 6’ in this paper has the highest mass attenuation and the smallest half value layer and may have potential applications in radiation shielding. An example dry storage cask utilizing an additional layer of Glass 6 as an intermediate shielding layer, simulated in MicroShield, is capable of reducing the exposure rate at the cask surface by over 20 orders of magnitude compared to the case without a glass layer. Based on this study, Glass 6 shows promise as a gamma-ray shielding material, particularly for dry cask storage.

Glass Ceramics Composites Fabricated from Coal Fly Ash and Waste Glass

International Nuclear Information System (INIS)

Angjusheva, B.; Jovanov, V.; Srebrenkoska, V.; Fidancevska, E.

2014-01-01

Great quantities of coal ash are produced in thermal power plants which present a double problem to the society: economical and environmental. This waste is a result of burning of coal at temperatures between 1100-14500C. Fly ash available as fine powder presents a source of important oxides SiO2, Al2O3, Fe2O3, MgO, Na2O, but also consist of small amount of ecologically hazardous oxides such as Cr2O3, NiO, MnO. The combination of the fly ash with waste glass under controlled sintering procedure gave bulk glass-ceramics composite material. The principle of this procedure is presented as a multi barrier concept. Many researches have been conducted the investigations for utilization of fly ash as starting material for various glass–ceramics production. Using waste glass ecologically hazardous components are fixed at the molecular level in the silicate phase and the fabricated new glass-ceramic composites possess significantly higher mechanical properties. The aim of this investigation was to fabricate dense glass ceramic composites using fly ash and waste glass with the potential for its utilization as building material

Synthesis and characterization of porous structured ZnO thin film for dye sensitized solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Marimuthu, T.; Anandhan, N., E-mail: anandhan-kn@rediffmail.com; Mummoorthi, M. [School of Physics, Alagappa University, Karaikudi – 630 003 (India); Dharuman, V. [Department of Bioelectronics and Biosensors, Alagappa University, Karaikudi – 630 003 (India)

2016-05-23

Zinc oxide (ZnO) and zinc oxide/eosin yellow (ZnO/EY) thin films were potentiostatically deposited onto fluorine doped tin oxide (FTO) glass substrate. Effect of eosin yellow dye on structural, morphological and optical properties was studied. X-ray diffraction patterns, micro Raman spectra and photoluminescence (PL) spectra reveal hexagonal wurtzite structure with less atomic defects in 101 plane orientation of the ZnO/EY film. Scanning electron microscopy (SEM) images show flower for ZnO and porous like structure for ZnO/EY thin film, respectively. DSSC was constructed and evaluated by measuring the current density verses voltage curve.

Study on Modified Water Glass Used in High Temperature Protective Glass Coating for Ti-6Al-4V Titanium Alloy

Directory of Open Access Journals (Sweden)

Shuang Yang

2018-04-01

Full Text Available Sodium silicate water glass was modified with sodium polyacrylate as the binder, the composite slurry used for high-temperature oxidation-resistant coating was prepared by mixing glass powder with good lubrication properties in the binder. The properties of the modified binder and high-temperature oxidation resistance of Ti-6Al-4V titanium alloy coated with composite glass coating were studied by XRD, SEM, EDS, TG-DSC and so on. Results showed that sodium polyacrylate modified water glass could obviously improve the suspension stability of the binder, the pyrolytic carbon in the binder at high temperature could increase the surface tension in the molten glass system, and the composite glass coating could be smooth and dense after heating. Pyrolytic carbon diffused and combined with oxygen in the coating under the heating process to protect the titanium alloy from oxidation. The thickness of the oxide layer was reduced 51% after applying the high-temperature oxidation-resistant coating. The coating also showed a nearly 30% reduction in friction coefficient due to the boundary lubricant regime. During cooling, the coating could be peeled off easily because of the mismatched CTE between the coating and substrate.

Structural and photoluminescence characterization of SnO{sub 2}: F thin films deposited by advanced spray pyrolysis technique at low substrate temperature

Energy Technology Data Exchange (ETDEWEB)

Shewale, P.S. [Thin Film Physics Laboratory, Department of Electronics, Shivaji University, Kolhapur 416004 (India); Ung Sim, Kyu; Kim, Ye-bin; Kim, J.H. [Department of Materials Science and Engineering, Chonnam National University, 300 Yongbong-Dong, Buk-Gu, Gwangju 500757 (Korea, Republic of); Moholkar, A.V. [Department of Physics, Shivaji University, Kolhapur 416004 (India); Uplane, M.D., E-mail: mdu_eln@unishivaji.ac.in [Thin Film Physics Laboratory, Department of Electronics, Shivaji University, Kolhapur 416004 (India)

2013-07-15

Fluorine doped tin oxide (FTO) thin films were deposited on glass substrates, at different substrate temperatures using advanced spray pyrolysis technique. X-ray diffraction studies showed that the crystallinity of the thin films increased with increasing substrate temperature. FESEM and AFM studies support the conclusions drawn from X-ray diffraction studies. X-ray photoelectron studies confirm oxygen deficiency in formation of the FTO nanocrystallites. The photoluminescence of the FTO films were investigated. It was found that, room temperature photoluminescence spectra are dominated by oxygen vacancies and exhibit a rich violet photoluminescence band about ∼404 nm with an extensively feeble red emission about 700 nm. The Photoluminescence intensity varies with the substrate temperature. The photoemission position is observed to be independent of substrate temperature. -- Highlights: ► Photoluminescent FTO thin films were deposited at low substrate temperatures. ► Influence of substrate temperature on the PL characteristics was studied. ► The samples are polycrystalline with a cassiterite tetragonal crystal structure. ► The room temperature UV/violet PL emission was dominated by the oxygen vacancies. ► PL efficiency is optimum at 613 K substrate temperature.

Stability and electronic properties of groups IIB to VB metal ions in unusual oxidation states and the 2S /SUB 1/2/ electronic state in lithium borate glasses

International Nuclear Information System (INIS)

Aleksandrov, A.I.; Bubnov, N.N.; Kraevskii, S.L.; Prokof'ev, A.I.; Raspertova, Z.I.; Solinov, V.F.

1986-01-01

The authors study lithium borate glasses containing groups IIB to VB metal oxides. Chemically pure reagents were used to synthesize the glasses which were subjected to gamma-rays at 77 and 300 K with doses of up to 100 kR. The EST spectra were recorded on a Varian E-12 spectrometer in the 3 cm CW frequency region with a 100 kHz magnetic field modulation. It was established that after gamma-irradiation at 77 and 300 K of the lithium borate glass system containing up to 10% of cadmium, tin, thalium, and lead oxides, additional ESR lines arise in the free electron g factor region. The authors have determined the missing ESR spectra for nonactivated lithium borate glasses by studying glasses with additions of Zn, Ge, and Sb oxides

Diffusion and ionic conduction in oxide glasses

International Nuclear Information System (INIS)

Mehrer, H; Imre, A W; Tanguep-Nijokep, E

2008-01-01

The ion transport properties of soda-lime silicate and alkali borate glasses have been studied with complimentary tracer diffusion and impedance spectroscopy techniques in order to investigate the ion dynamics and mixed-alkali effect (MAE). In soda-lime silicate glasses the tracer diffusivity of 22 Na alkali ions is more than six orders of magnitude faster than the diffusivity of earth alkali 45 Ca ions. This observation is attributed to a stronger binding of bivalent earth alkali ions to the glass network as compared to that of alkali ions. The conductivity of the investigated standard soda-lime silicate glasses is mostly due to the high mobility of sodium ions and a temperature independent Haven ratio of about 0.45 is obtained. For single alkali sodium-borate glasses, the Haven ratio is also temperature independent, however, it is decreases with decreasing temperature for rubidium-borate glass. The MAE was investigated for Na-Rb borate glasses and it was observed that the tracer diffusivities of 22 Na and 86 Rb ions cross, when plotted as function of the relative alkali content. This crossover occurs near the Na/(Na+Rb) ratio of the conductivity minimum due to MAE. The authors suggest that this crossover and the trend of diffusion coefficients is the key to an understanding of the MAE

Improvement of Transparent Conducting Performance on Oxygen-Activated Fluorine-Doped Tin Oxide Electrodes Formed by Horizontal Ultrasonic Spray Pyrolysis Deposition.

Science.gov (United States)

Koo, Bon-Ryul; Oh, Dong-Hyeun; Riu, Doh-Hyung; Ahn, Hyo-Jin

2017-12-27

In this study, highly transparent conducting fluorine-doped tin oxide (FTO) electrodes were fabricated using the horizontal ultrasonic spray pyrolysis deposition. In order to improve their transparent conducting performances, we carried out oxygen activation by adjusting the ratio of O 2 /(O 2 +N 2 ) in the carrier gas (0%, 20%, and 50%) used during the deposition process. The oxygen activation on the FTO electrodes accelerated the substitution concentration of F (F O • ) into the oxygen sites in the FTO electrode while the oxygen vacancy (V O • • ) concentration was reduced. In addition, due to growth of pyramid-shaped crystallites with (200) preferred orientations, this oxygen activation caused the formation of a uniform surface structure. As a result, compared to others, the FTO electrode prepared at 50% O 2 showed excellent electrical and optical properties (sheet resistance of ∼4.0 ± 0.14 Ω/□, optical transmittance of ∼85.3%, and figure of merit of ∼5.09 ± 0.19 × 10 -2 Ω -1 ). This led to a superb photoconversion efficiency (∼7.03 ± 0.20%) as a result of the improved short-circuit current density. The photovoltaic performance improvement can be defined by the decreased sheet resistance of FTO used as a transparent conducting electrode in dye-sensitized solar cells (DSSCs), which is due to the combined effect of the high carrier concentration by the improved F O • concentration on the FTO electrodes and the fasted Hall mobility by the formation of a uniform FTO surface structure and distortion relaxation on the FTO lattices resulting from the reduced V O • • • concentration.

A novel intermediate layer for Au/CdZnTe/FTO photoconductive structure

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yuelu; Wang, Linjun, E-mail: ljwang@shu.edu.cn; Xu, Run; Huang, Jian; Tao, Jun; Meng, Hua; Zhang, Jijun; Min, Jiahua

2016-12-01

Highlights: • Graphene layer was spin-coated on CdZnTe to form Au/graphene/CdZnTe/FTO structure. • Graphene layer can significantly improve the contact property of Au/CdZnTe. • Graphene layer can obviously enhance UV photo-response of CdZnTe. • Graphene is a potential buffer material for CdZnTe based high-energy detectors. - Abstract: In this work, graphene is tried to use to improve the performance of polycrystalline CdZnTe high-energy radiation and photon detectors. A graphene intermediate layer is prepared by spin-coating process on the surface of polycrystalline CdZnTe film, which forms a photoconductive Au/graphene/CdZnTe/FTO structure. XRD, Raman, photoelectric response and other characterisation methods are adopted to investigate the effect of graphene layer on the electrical characteristics and UV photo-response performance of CdZnTe photoconductive structure. It is demonstrated that graphene layer can significantly improve the contact property of Au/CdZnTe structure, and obviously enhance its UV photo-response and the UV sensitivity increased with one order of magnitude.

Effects of composition on waste glass properties

International Nuclear Information System (INIS)

Mellinger, G.B.; Chick, L.A.

1979-01-01

The electrical conductivity, viscosity, chemical durability, devitrification, and crystallinity of a defense waste glass were measured. Each oxide component in the glass was varied to determine its effect on these properties. A generic study is being developed which will determine the effects of 26 oxides on the above and additional properties of a wide field of possible waste glasses. 5 figures, 2 tables

Preparation of glasses and glass ceramics of heavy metal oxides containing silver: optical, structural and electrochemical properties; Preparacao de vidros e vitroceramicas de oxidos de metais pesados contendo prata: propriedades opticas, estruturais e eletroquimicas

Energy Technology Data Exchange (ETDEWEB)

Bregadiolli, Bruna A. [Departamento de Fisica, Faculdade de Ciencias, Universidade Estadual Paulista, Bauru - SP (Brazil); Souza, Ernesto R.; Sigoli, Fernando A. [Instituto de Quimica, Universidade Estadual de Campinas, Campinas - SP (Brazil); Caiut, Jose M.A. [Departamento de Quimica, Faculdade de Filosofia Ciencias e Letras de Ribeirao Preto, Universidade de Sao Paulo, Ribeirao Preto - SP (Brazil); Alencar, Monica A.S.; Benedetti, Assis V. [Instituto de Quimica, Universidade Estadual Paulista, Araraquara - SP (Brazil); Nalin, Marcelo, E-mail: mnalin@ufscar.br [Departamento de Quimica, Universidade Federal de Sao Carlos, SP, (Brazil)

2012-07-01

Silver containing heavy metal oxide glasses and glass ceramics of the system WO{sub 3}-SbPO{sub 4} -PbO-AgCl with different AgCl contents have been prepared and their thermal, structural and optical properties characterized. Glass ceramics containing metallic silver nanoparticles have been prepared by annealing glass samples at temperatures above the glass transition and analyzed by transmission electron microscopy and energy dispersive X-ray microanalysis. The presence of the metallic clusters has been also confirmed by the observation of a surface plasmon resonance band in the visible range. Cyclic voltammetric measurements indicated the presence of metallic silver into the glasses, even before to perform the thermal treatment. (author)

Improving the chemical compatibility of sealing glass for solid oxide fuel cells: Blocking the reactive species by controlled crystallization

Science.gov (United States)

Zhang, Teng; Zou, Qi; Zeng, Fanrong; Wang, Shaorong; Tang, Dian; Yang, Hiswen

2012-10-01

The chemical compatibility of sealing glass is of great importance for Solid oxide fuel cell (SOFC). In this work, the interfacial reaction between sealing glass and Cr-containing interconnect alloy is characterized by reacting Cr2O3 powders with a representative SrO-containing glass crystallized by different heat-treatment schedules. The crystalline structure and crystalline content of sealing glass are determined by X-ray diffraction. The results show that the fraction of Cr6+ decreases from 39.8 ± 1.9% for quenched glass to 8.2 ± 0.4% for glass crystallized at 900 °C for 2 h. In addition, the interfacial reaction can be further reduced with increasing crystallization temperature and time as well as the addition of nucleation agent (TiO2). The formation of some Sr-containing crystalline phases, Sr2SiO4 and Sr(TiO3), contributes to the improvement of chemical compatibility of sealing glass, in agreement with the results of thermodynamic calculations.

Vertically grown zinc oxide nanorods functionalized with ferric oxide for in vivo and non-enzymatic glucose detection

Science.gov (United States)

Marie, Mohammed; Manoharan, Anishkumar; Kuchuk, Andrian; Ang, Simon; Manasreh, M. O.

2018-03-01

An enzyme-free glucose sensor based on vertically grown zinc oxide nanorods (NRs) functionalized with ferric oxide (Fe2O3) is investigated. The well-aligned and high density ZnO NRs were synthesized on an FTO/glass substrate by a sol-gel and hydrothermal growth method. A dip-coating technique was utilized to modify the surface of the as-grown ZnO NRs with Fe2O3. The immobilized surface was coated with a layer of nafion membrane. The fabricated glucose sensor was characterized amperometrically at room temperature using three electrodes stationed in the phosphate buffer solution, where ZnO NRs/Fe2O3/nafion membrane was the sensing or working electrode, and platinum plate and silver/silver chloride were used as the counter and reference electrodes, respectively. The proposed non-enzymatic and modified glucose sensor exhibited a high sensitivity in the order of 0.052 μA cm-2 (mg/dL)-1, a lower detection limit of around 0.95 mmol L-1, a sharp and fast response time of ˜1 s, and a linear response to changes in glucose concentrations from 100-400 mg dL-1. The linear amperometric response of the sensor covers the physiological and clinical interest of glucose levels for diabetic patients. The device continues to function accurately after multiple measurements with a good reproducibility. The proposed glucose sensor is expected to be used clinically for in vivo monitoring of glucose.

Statistical and biological gene-lifestyle interactions of MC4R and FTO with diet and physical activity on obesity: new effects on alcohol consumption

Science.gov (United States)

Fat mass and obesity (FTO) and melanocortin-4 receptor (MC4R) and are relevant genes associated with obesity. This could be through food intake, but results are contradictory. Modulation by diet or other lifestyle factors is also not well understood. To investigate whether MC4R and FTO associations ...

Nanostructured hydrophobic DC sputtered inorganic oxide coating for outdoor glass insulators

Energy Technology Data Exchange (ETDEWEB)

Dave, V. [Department of Electrical Engineering, Indian Institute of Technology Roorkee, Roorkee 247667 (India); Institute Instrumentation Centre, Indian Institute of Technology, Roorkee, Roorkee 247667 (India); Gupta, H.O. [Department of Electrical Engineering, Indian Institute of Technology Roorkee, Roorkee 247667 (India); Chandra, R., E-mail: ramesfic@gmail.com [Institute Instrumentation Centre, Indian Institute of Technology, Roorkee, Roorkee 247667 (India)

2014-03-01

Graphical abstract: - Highlights: • Deposition of contamination on outdoor glass insulators and its physical and economical consequences were discussed. • Synthesis of nanostructured hydrophobic HfO{sub 2} film on glass as a remedial measure by varying DC sputtering power. • Investigated and correlated structural, optical, electrical and hydrophobic properties of HfO{sub 2} films with respect to power. • Optimum results were obtained at a 50 W DC sputtering power. - Abstract: We report the structural, optical and electrical properties of nanostructured hydrophobic inorganic hafnium oxide coating for outdoor glass insulator using DC sputtering technique to combat contamination problem. The properties were studied as a function of DC power. The characterization of the films was done using X-ray diffraction, EDS, surface profilometer, AFM, impedance analyser and water contact angle measurement system. The DC power was varied from 30 to 60 W and found to have a great impact on the properties of hafnium oxide. All the deposited samples were polycrystalline with nanostructured hydrophobic surfaces. The intensity of crystallinity of the film was found to be dependent on sputtering power and hydrophobicity was correlated to the nanoscale roughness of the films. The optical property reveals 80% average transmission for all the samples. The refractive index was found in the range of 1.85–1.92, near to the bulk value. The band gap calculated from transmission data was >5.3 eV for all deposited samples ensuring dielectric nature of the films. Surface energy calculated by two methods was found minimum for the film deposited at 50 W sputtering power. The resistivity was also high enough (∼10{sup 4} Ω cm) to hinder the flow of leakage current through the film. The dielectric constant (ε) was found to be thickness dependent and also high enough (ε{sub max} = 23.12) to bear the large electric field of outdoor insulators.

Moessbauer effect study of oxidation and coordination states of iron in some sodium borate glasse:;

International Nuclear Information System (INIS)

Eissa, N.A.; Sanad, A.M.; Youssef, S.M.; El-Henawii, S.A.; Gomaa, S.Sh.; Mostafa, A.G.

1980-01-01

A structural study of some sodium borate glasses containing iron was carried out applying ME spectroscopy. Both oxidation and coordination states of iron were investigated under the effect of gradual replacing of sodium carbonate by sodium nitrate in the glass batches. The glasses were melted in porcelain crucibles using an electrically heated furnace at 1000+-10 deg C, then were quenched on a steel plate at room temperature (R.T.). The ME source was 20 mCi radioactive Co-57 in chromium. The obtained ME spectra indicated that at lower sodium nitrate content both Fe 2+ and Fe 3+ are present in these glasses. At moderate concentrations some Fe 3+ ions were separated in a crystalline phase and the rest of the iron ions appeared as ferric ions in glassy state. At high sodium nitrate content only Fe 3+ ions in glassy state were detected. The values of the ME parameters for all iron ions indicated that all of them are in the octahedral coordination state. The density measurements confirm the separation of a crystalline phase at moderate sodium nitrate content. (author)

Urea impedimetric biosensing using electrospun nanofibers modified with zinc oxide nanoparticles

Science.gov (United States)

Migliorini, Fernanda L.; Sanfelice, Rafaela C.; Mercante, Luiza A.; Andre, Rafaela S.; Mattoso, Luiz H. C.; Correa, Daniel. S.

2018-06-01

Reliable analytical techniques to evaluate dairy products, including milk, are of outmost importance to ensure food safety against contaminants. Among possible substances employed as adulterants in milk, urea raises deep concern due to its harmful effects to consumer's health. In the present study, a biosensing platform was developed to be applied in the electrochemical detection of urea. The sensing platform was fabricated using polymeric electrospun nanofibers of polyamide 6 (PA6) and polypyrrole (PPy) deposited onto fluorine doped tin oxide (FTO) electrodes, which were then modified with zinc oxide nanoparticles (ZnO). This material showed excellent properties for the immobilization of urease enzyme, conferring the FTO/PA6/PPy/ZnO/urease electrode high sensitivity for urea detection within the concentration range between 0.1 and 250 mg dL-1 with a limit of detection of 0.011 mg dL-1. The results achieved evidence the potential of electrospun nanofibers-based electrodes for applications in biosensors aiming at dairy products analysis.

Genome wide association (GWA study for early onset extreme obesity supports the role of fat mass and obesity associated gene (FTO variants.

Directory of Open Access Journals (Sweden)

Anke Hinney

2007-12-01

Full Text Available Obesity is a major health problem. Although heritability is substantial, genetic mechanisms predisposing to obesity are not very well understood. We have performed a genome wide association study (GWA for early onset (extreme obesity.a GWA (Genome-Wide Human SNP Array 5.0 comprising 440,794 single nucleotide polymorphisms for early onset extreme obesity based on 487 extremely obese young German individuals and 442 healthy lean German controls; b confirmatory analyses on 644 independent families with at least one obese offspring and both parents. We aimed to identify and subsequently confirm the 15 SNPs (minor allele frequency > or =10% with the lowest p-values of the GWA by four genetic models: additive, recessive, dominant and allelic. Six single nucleotide polymorphisms (SNPs in FTO (fat mass and obesity associated gene within one linkage disequilibrium (LD block including the GWA SNP rendering the lowest p-value (rs1121980; log-additive model: nominal p = 1.13 x 10(-7, corrected p = 0.0494; odds ratio (OR(CT 1.67, 95% confidence interval (CI 1.22-2.27; OR(TT 2.76, 95% CI 1.88-4.03 belonged to the 15 SNPs showing the strongest evidence for association with obesity. For confirmation we genotyped 11 of these in the 644 independent families (of the six FTO SNPs we chose only two representing the LD bock. For both FTO SNPs the initial association was confirmed (both Bonferroni corrected p<0.01. However, none of the nine non-FTO SNPs revealed significant transmission disequilibrium.Our GWA for extreme early onset obesity substantiates that variation in FTO strongly contributes to early onset obesity. This is a further proof of concept for GWA to detect genes relevant for highly complex phenotypes. We concurrently show that nine additional SNPs with initially low p-values in the GWA were not confirmed in our family study, thus suggesting that of the best 15 SNPs in the GWA only the FTO SNPs represent true positive findings.

Sodium aluminum-iron phosphate glass-ceramics for immobilization of lanthanide oxide wastes from pyrochemical reprocessing of spent nuclear fuel

Science.gov (United States)

Stefanovsky, S. V.; Stefanovsky, O. I.; Kadyko, M. I.; Nikonov, B. S.

2018-03-01

Sodium aluminum (iron) phosphate glass ceramics containing of up to 20 wt.% rare earth (RE) oxides simulating pyroprocessing waste were produced by melting at 1250 °C followed by either quenching or slow cooling to room temperature. The iron-free glass-ceramics were composed of major glass and minor phosphotridymite and monazite. The iron-bearing glass-ceramics were composed of major glass and minor monazite and Na-Al-Fe orthophosphate at low waste loadings (5-10 wt.%) and major orthophosphate and minor monazite as well as interstitial glass at high waste loadings (15-20 wt.%). Slowly cooled samples contained higher amount of crystalline phases than quenched ones. Monazite is major phase for REs. Leach rates from the materials of major elements (Na, Al, Fe, P) are 10-5-10-7 g cm-2 d-1, RE elements - lower than 10-5 g cm-2 d-1.

Enhancement of open-circuit voltage on organic photovoltaic devices by Al-doped TiO2 modifying layer produced by sol–gel method

International Nuclear Information System (INIS)

Valaski, R.; Arantes, C.; Senna, C.A.; Carôzo, Victor; Achete, C.A.; Cremona, M.

2014-01-01

Sol–gel method has shown several advantages for oxide synthesis, such as lower cost production, coating large areas, lower processing temperatures and ease insertion of doping materials. Therefore, it is attractive for production of intermediate and electrode modifying layers in organic optoelectronic devices. Herein, spin-coated aluminum-doped titanium dioxide (AlTiO 2 ) thin films were produced by sol–gel method onto glass and fluorine-doped tin oxide (FTO) substrates, using different Al-dopant concentrations and post-done annealing temperatures. Electrical measurements were performed in order to investigate the improvement of the TiO 2 resistivity. Additionally, structural, compositional, morphological, optical and electrical properties of the optimal AlTiO 2 modifying layers onto FTO substrates were probed by different techniques, and compared with those obtained from the undoped thin films produced under similar conditions. Organic photovoltaic devices (OPVs) with the structure FTO/AlTiO 2 (30 nm)/C 60 (50 nm)/CuPc(50 nm)/Al with an Al concentration of 0.03 M in AlTiO 2 layer were produced. The insertion of AlTiO 2 thin films improved the short-circuit current density (J sc ) as well as the open circuit voltage (V oc ) in comparison with non-modified electrode FTO based devices. This behavior is discussed in terms of induced interface phenomena as dipole formation induced by Al. - Highlights: • Easy and cheap solution-process for AlTiO 2 modification of FTO electrode for OPVs • Electrical, structural and optical characterization of TiO 2 layers with Al-dopant • Improvement of Voc and Jsc of inverted OPVs with AlTiO 2 modified electrode

A structural bond strength model for glass durability

International Nuclear Information System (INIS)

Feng, Xiangdong; Metzger, T.B.

1996-01-01

A glass durability model, structural bond strength (SBS) model was developed to correlate glass durability with its composition. This model assumes that the strengths of the bonds between cations and oxygens and the structural roles of the individual elements in the glass arc the predominant factors controlling the composition dependence of the chemical durability of glasses. The structural roles of oxides in glass are classified as network formers, network breakers, and intermediates. The structural roles of the oxides depend upon glass composition and the redox state of oxides. Al 2 O 3 , ZrO 2 , Fe 2 O 3 , and B 2 O 3 are assigned as network formers only when there are sufficient alkalis to bind with these oxides. CaO can also improve durability by sharing non-bridging oxygen with alkalis, relieving SiO 2 from alkalis. The percolation phenomenon in glass is also taken into account. The SBS model is applied to correlate the 7-day product consistency test durability of 42 low-level waste glasses with their composition with an R 2 of 0.87, which is better than 0.81 obtained with an eight-coefficient empirical first-order mixture model on the same data set

Electrical properties of phosphate glasses

International Nuclear Information System (INIS)

Mogus-Milankovic, A; Santic, A; Reis, S T; Day, D E

2009-01-01

Investigation of the electrical properties of phosphate glasses where transition metal oxide such as iron oxide is the network former and network modifier is presented. Phosphate glasses containing iron are electronically conducting glasses where the polaronic conduction is due to the electron hopping from low to high iron valence state. The identification of structural defects caused by ion/polaron migration, the analysis of dipolar states and electrical conductivity in iron phosphate glasses containing various alkali and mixed alkali ions was performed on the basis of the impedance spectroscopy (IS). The changes in electrical conductivity from as-quenched phosphate glass to fully crystallized glass (glass-ceramics) by IS are analyzed. A change in the characteristic features of IS follows the changes in glass and crystallized glass network. Using IS, the contribution of glass matrix, crystallized grains and grain boundary to the total electrical conductivity for iron phosphate glasses was analyzed. It was shown that decrease in conductivity is caused by discontinuities in the conduction pathways as a result of the disruption of crystalline network where two or more crystalline phases are formed. Also, phosphate-based glasses offer a unique range of biomaterials, as they form direct chemical bonding with hard/soft tissue. The surface charges of bioactive glasses are recognized to be the most important factors in determining biological responses. The improved bioactivity of the bioactive glasses as a result of the effects of the surface charges generated by electrical polarization is discussed.

Comprehension and modelling of chromia-forming alloys corrosion mechanisms in nuclear glasses

International Nuclear Information System (INIS)

Schmucker, Eric

2016-01-01

Nuclear wastes management consists in the confinement of the radioactive wastes in a glass matrix. This is made by inductive melting in a hot crucible at an operating temperature around 1150 C. These crucibles are constituted of nickel based superalloys with high chromium content. They are submitted to a harsh corrosion by the molten glass, eventually leading to their replacement. The protection of the crucible against corrosion is best provided by the establishment of a protective chromium oxide layer at the surface of the alloy. A binary chromia-forming alloy (Ni-30Cr) is studied in this work. Three different binary and ternary glass compositions are chosen in order to understand the influence of the glass basicity and glass viscosity on the corrosion kinetics. Besides, the de-correlation of the formation and dissolution kinetics of the oxide layer allows the modelling of the overall oxide growth in the molten glass. For that purpose, the oxide formation kinetics in molten glass media is assimilated to the oxidation kinetics of the alloy in gaseous media with oxygen partial pressure that are representative of the redox properties of the glasses. Studies of the oxidation kinetics and of the diffusion mechanisms have shown that the oxidation kinetics is independent on the oxygen pressure in the range of 10"-"1"3 up to 10"-"3 atm O_2 at 1150 C. The present work has shown that the dissolution kinetics of the oxide layer is governed by the diffusion of Cr(III) in the glass melt. This dissolution kinetics has been evaluated from the diffusion coefficient and the solubility limit of Cr(III) in the glass. Finally, the overall growth kinetics of the Cr_2O_3 layer in the glass has been successfully modelled for each glass, thanks to the knowledge of (i) the solubility limit of Cr(III), (ii) its diffusion coefficient in the glasses and (iii) the oxidation kinetics of the alloy. The presented model also allows quantifying the influence of each of these parameters on the

Decontamination processes for waste glass canisters

International Nuclear Information System (INIS)

Rankin, W.N.

1981-06-01

The process which will be used to decontaminate waste glass canisters at the Savannah River Plant consists of: decontamination (slurry blasting); rinse (high-pressure water); and spot decontamination (high-pressure water plus slurry). No additional waste will be produced by this process because glass frit used in decontamination will be mixed with the radioactive waste and fed into the glass melter. Decontamination of waste glass canisters with chemical and abrasive blasting techniques was investigated. The ability of a chemical technique with HNO 3 -HF and H 2 C 2 O 4 to remove baked-on contamination was demonstrated. A correlation between oxide removal and decontamination was observed. Oxide removal and, thus, decontamination by abrasive blasting techniques with glass frit as the abrasive was proposed and demonstrated

Corrosion of simulated nuclear waste glass

International Nuclear Information System (INIS)

Music, S.; Ristic, M.; Gotic, M.; Foric, J.

1988-01-01

In this study the preparation and characterization of borosilicate glasses of different chemical composition were investigated. Borosilicate glasses were doped with simulated nuclear waste oxides. The chemical corrosion in water of these glasses was followed by measuring the leach rates as a function of time. It was found that a simulated nuclear waste glass with the chemical composition (weight %), 15.61% Na 2 O, 10.39% B 2 O 3 , 45.31% SiO 2 , 13.42% ZnO, 6.61% TiO 2 and 8.66% waste oxides, is characterized by low melting temperature and with good corrosion resistance in water. Influence of passive layers on the leaching behaviour of nuclear waste glasses is discussed. (author) 20 refs.; 7 figs.; 4 tabs

Decontamination processes for waste glass canisters

International Nuclear Information System (INIS)

Rankin, W.N.

1981-01-01

The process which will be used to decontaminate waste glass canisters at the Savannah River Plant consists of: decontamination (slurry blasting); rinse (high-pressure water); and spot decontamination (high-pressure water plus slurry). No additional waste will be produced by this process because glass frit used in decontamination will be mixed with the radioactive waste and fed into the glass melter. Decontamination of waste glass canisters with chemical and abrasive blasting techniques was investigated. The ability of a chemical technique with HNO 3 -HF and H 2 C 2 O 4 to remove baked-on contamination was demonstrated. A correlation between oxide removal and decontamination was observed. Oxide removal and, thus, decontamination by abrasive blasting techniques with glass frit as the abrasive was proposed and demonstrated

The electrical properties of semiconducting vanadium phosphate glasses

International Nuclear Information System (INIS)

Moridi, G.R.; Hogarth, C.A.; Hekmat Shooar, N.H.

1984-01-01

Vanadium phosphate glasses are a group of oxide glasses which show the semiconducting behaviour. In contrast to the conventional glasses, the conduction mechanism in these glasses is electronic, rather than being ionic. Since 1954, when the first paper appeared on the semiconducting properties of these glasses, much work has been carried out on transition-metal-oxide glasses in general, and vanadium phosphate glasses in particular. The mechanism of conduction is basicaly due to the transport of electrons between the transition-metal ions in different valency states. In the present paper, we have reviewed the previous works on the electrical characteristics of P 2 O 5 -V 2 O 5 glasses and also discussed the current theoretical ideas relevant for the interpretation of the experimental data

Hydrophobic and optical characteristics of graphene and graphene oxide films transferred onto functionalized silica particles deposited glass surface

Science.gov (United States)

Yilbas, B. S.; Ibrahim, A.; Ali, H.; Khaled, M.; Laoui, T.

2018-06-01

Hydrophobic and optical transmittance characteristics of the functionalized silica particles on the glass surface prior and after transfer of graphene and graphene oxide films on the surface are examined. Nano-size silica particles are synthesized and functionalized via chemical grafting and deposited onto a glass surface. Graphene film, grown on copper substrate, was transferred onto the functionalized silica particles surface through direct fishing method. Graphene oxide layer was deposited onto the functionalized silica particles surface via spin coating technique. Morphological, hydrophobic, and optical characteristics of the functionalized silica particles deposited surface prior and after graphene and graphene oxide films transfer are examined using the analytical tools. It is found that the functionalized silica particles are agglomerated at the surface forming packed structures with few micro/nano size pores. This arrangement gives rise to water droplet contact angle and contact angle hysteresis in the order of 163° and 2°, respectively, and remains almost uniform over the entire surface. Transferring graphene and depositing graphene oxide films over the functionalized silica particles surface lowers the water droplet contact angle slightly (157-160°) and increases the contact angle hysteresis (4°). The addition of the graphene and graphene oxide films onto the surface of the deposited functionalized silica particles improves the optical transmittance.

Deposition of tin oxide doped with fluorine produced by sol-gel method and deposited by spray-pyrolysis

International Nuclear Information System (INIS)

Maia, Paulo Herbert Franca; Lima, Francisco Marcone; Sena, Aline Cosmo de; Silva, Alvaro Neuton; Almeida, Ana Fabiola Leite de; Freire, Francisco Nivaldo Aguiar

2014-01-01

Solar energy is one of the most important sources of renewable energy today, but its production is based on silicon cells, expensive and difficult to produce, so the research seek new materials to replace them. This work aims to deposit tin oxide doped with fluorine on the glass substrate using the sol-gel method to provide a working solution and spray pyrolysis technique to perform the deposition. F-SnO2 (FTO) were synthesized by sol-gel method, employing NH_4F and SnCl_2 precursor in an ethanol solution. Before the formation of the gel phase, the entire solution was sprayed, with the aid of a pistol aerographic substrate under heated at 600 °C divided by 50 applications and cooled in the furnace. The substrates had resistances between 10 and 30 S.cm. The energy dispersive x-ray (EDS) revealed the presence of fluorine in the SnO_2 network. (author)

Reaction products and corrosion of molybdenum electrode in glass melt containing antimony oxides and sodium sulfate

Czech Academy of Sciences Publication Activity Database

Matěj, J.; Langrová, Anna

2012-01-01

Roč. 56, č. 3 (2012), s. 280-285 ISSN 0862-5468 Institutional support: RVO:67985831 Keywords : antimony oxides * corrosion * glass melt * Molybdenum electrode * sulfate Subject RIV: DD - Geochemistry Impact factor: 0.418, year: 2012 http://www.ceramics-silikaty.cz/2012/pdf/2012_03_280.pdf

Sea-Urchin-Like ZnO Nanoparticle Film for Dye-Sensitized Solar Cells

Directory of Open Access Journals (Sweden)

Cheng-Wen Ma

2015-01-01

Full Text Available We present novel sea-urchin-like ZnO nanoparticles synthesized using a chemical solution method. Solution approaches to synthesizing ZnO nanostructures have several advantages including low growth temperatures and high potential for scaling up. We investigated the influence of reaction times on the thickness and morphology of sea-urchin-like ZnO nanoparticles, and XRD patterns show strong intensity in every direction. Dye-sensitized solar cells (DSSCs were developed using the synthesized ZnO nanostructures as photoanodes. The DSSCs comprised a fluorine-doped tin oxide (FTO glass with dense ZnO nanostructures as the working electrode, a platinized FTO glass as the counter electrode, N719-based dye, and I-/I3-liquid electrolyte. The DSSC fabricated using such nanostructures yielded a high power conversion efficiency of 1.16% with an incident photo-to-current efficiency (IPCE as high as 15.32%. Electrochemical impedance spectroscopy was applied to investigate the characteristics of DSSCs. An improvement in the electron transport in the ZnO photoanode was also observed.

Fat phenotype, associated factors and rs9939609 polymorphism of the FTO gene DOI:10.5007/1980-0037.2010v12n2p164

Directory of Open Access Journals (Sweden)

William Alves Lima

2010-07-01

Full Text Available The purpose of this work was to review the main results of studies that have analysed the relationship between the rs9939609 single nucleotide polymorphism (SNP of the FTO gene and the manifestation of overweight/obesity with its associated co-morbidity, and to discuss the interaction of this polymorphism with the other factors which cause obesity. The search was performed using the MEDLINE, Highwire, Science Direct and SciELO databases, applying the following key words: FTO rs9939609, obesity genetic, gene associated obesity, FTO contributes obesity. Inclusion criteria were: original articles where the search was performed in humans and including the rs9939609. Articles that analysed the FTO gene associated with preinstalled hormonal diseases were excluded. Of the several SNP associated with the FTO gene, rs9939609 has been the most researched (studied. This SNP comprises the A and T alleles, with the A homozygote being most susceptible to the development of overweight/obesity in all age ranges, especially in the caucasian population. In this situation, the control of environmental factors (alimentation and physical activity can prevent the excessive build up of fats. Obesity is related to the development of non-transmissible chronic illnesses. Association of rs9939609 polymorphism with the lipidic profile and glycemia were observed. The practicing of physical exercise and feeding habits seem to be the main contributors in the development of overweight/obesity and its resulting co-morbidity.

Urea impedimetric biosensor based on reactive RF magnetron sputtered zinc oxide nanoporous transducer

International Nuclear Information System (INIS)

Mozaffari, Sayed Ahmad; Rahmanian, Reza; Abedi, Mohammad; Amoli, Hossein Salar

2014-01-01

Graphical abstract: - Highlights: • Application and optimization of reactive RF magnetron sputtering for homogeneous nanoporous ZnO thin film formation. • Exploiting nanoporous ZnO thin film as a good porous framework with large surface area/volume for having stable immobilized enzyme with minimum loss of activity. • Application of impedimetric assessment for urea biosensing due to its rapidity, sensitivity, and repeatability. - Abstract: Uniform sputtered nanoporous zinc oxide (Nano-ZnO) thin film on the conductive fluorinated-tin oxide (FTO) layer was applied to immobilize urease enzyme (Urs) for urea detection. Highly uniform nanoporous ZnO thin film were obtained by reactive radio frequency (RF) magnetron sputtering system at the optimized instrumental deposition conditions. Characterization of the surface morphology and roughness of ZnO thin film by field emission-scanning electron microscopy (FE-SEM) exhibits cavities of nanoporous film as an effective biosensing area for enzyme immobilization. Step by step monitoring of FTO/Nano-ZnO/Urs biosensor fabrication were performed using electrochemical methods such as cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques. Fabricated FTO/Nano-ZnO/Urs biosensor was used for urea determination using EIS experiments. The impedimetric results show high sensitivity for urea detection within 0.83–23.24 mM and limit of detection as 0.40 mM

BNFL Report Glass Formers Characterization

Energy Technology Data Exchange (ETDEWEB)

Schumacher, R.F.

2000-07-27

The objective of this task was to obtain powder property data on candidate glass former materials, sufficient to guide conceptual design and estimate the cost of glass former handling facilities as requested under Part B1 of BNFL Technical and Development Support. Twenty-nine glass forming materials were selected and obtained from vendors for the characterization of their physical properties, durability in caustic solution, and powder flow characteristics. A glass former was selected based on the characterization for each of the ten oxide classes required for Envelope A, B, and C mixtures. Three blends (A, B, and C) were prepared based on formulations provided by Vitreous State Laboratory and evaluated with the same methods employed for the glass formers. The properties obtained are presented in a series of attached Tables. It was determined that five of the ten glass formers, (kyanite, iron oxide, titania, zircon, and zinc oxide) have the potential to cause some level of solids f low problems. In addition, all of the blends may require consideration for their handling. A number of engineering considerations and recommendations were prepared based on the experimental findings, experience, and other process considerations. Recommendations for future testing are included. In conjunction with future work, it is recommended that a professional consultant be engaged to guide and assist with testing and design input.

BNFL Report Glass Formers Characterization

International Nuclear Information System (INIS)

Schumacher, R.F.

2000-01-01

The objective of this task was to obtain powder property data on candidate glass former materials, sufficient to guide conceptual design and estimate the cost of glass former handling facilities as requested under Part B1 of BNFL Technical and Development Support. Twenty-nine glass forming materials were selected and obtained from vendors for the characterization of their physical properties, durability in caustic solution, and powder flow characteristics. A glass former was selected based on the characterization for each of the ten oxide classes required for Envelope A, B, and C mixtures. Three blends (A, B, and C) were prepared based on formulations provided by Vitreous State Laboratory and evaluated with the same methods employed for the glass formers. The properties obtained are presented in a series of attached Tables. It was determined that five of the ten glass formers, (kyanite, iron oxide, titania, zircon, and zinc oxide) have the potential to cause some level of solids f low problems. In addition, all of the blends may require consideration for their handling. A number of engineering considerations and recommendations were prepared based on the experimental findings, experience, and other process considerations. Recommendations for future testing are included. In conjunction with future work, it is recommended that a professional consultant be engaged to guide and assist with testing and design input

FTO variant rs9939609 is associated with body mass index and waist circumference, but not with energy intake or physical activity in European- and African-American youth

NARCIS (Netherlands)

Liu, Gaifen; Zhu, Haidong; Lagou, Vasiliki; Gutin, Bernard; Stallmann-Jorgensen, Inger S.; Treiber, Frank A.; Dong, Yanbin; Snieder, Harold

2010-01-01

Background: Genome-wide association studies found common variants in the fat mass and obesity-associated (FTO) gene associated with adiposity in Caucasians and Asians but the association was not confirmed in African populations. Association of FTO variants with insulin resistance and energy intake

Controllable Electrochemical Synthesis of Reduced Graphene Oxide Thin-Film Constructed as Efficient Photoanode in Dye-Sensitized Solar Cells

Directory of Open Access Journals (Sweden)

Soon Weng Chong

2016-01-01

Full Text Available A controllable electrochemical synthesis to convert reduced graphene oxide (rGO from graphite flakes was introduced and investigated in detail. Electrochemical reduction was used to prepare rGO because of its cost effectiveness, environmental friendliness, and ability to produce rGO thin films in industrial scale. This study aimed to determine the optimum applied potential for the electrochemical reduction. An applied voltage of 15 V successfully formed a uniformly coated rGO thin film, which significantly promoted effective electron transfer within dye-sensitized solar cells (DSSCs. Thus, DSSC performance improved. However, rGO thin films formed in voltages below or exceeding 15 V resulted in poor DSSC performance. This behavior was due to poor electron transfer within the rGO thin films caused by poor uniformity. These results revealed that DSSC constructed using 15 V rGO thin film exhibited high efficiency (η = 1.5211% attributed to its higher surface uniformity than other samples. The addition of natural lemon juice (pH ~ 2.3 to the electrolyte accelerated the deposition and strengthened the adhesion of rGO thin film onto fluorine-doped tin oxide (FTO glasses.

Freeform Fabrication of Magnetophotonic Crystals with Diamond Lattices of Oxide and Metallic Glasses for Terahertz Wave Control by Micro Patterning Stereolithography and Low Temperature Sintering

Directory of Open Access Journals (Sweden)

Maasa Nakano

2013-04-01

Full Text Available Micrometer order magnetophotonic crystals with periodic arranged metallic glass and oxide glass composite materials were fabricated by stereolithographic method to reflect electromagnetic waves in terahertz frequency ranges through Bragg diffraction. In the fabrication process, the photo sensitive acrylic resin paste mixed with micrometer sized metallic glass of Fe72B14.4Si9.6Nb4 and oxide glass of B2O3·Bi2O3 particles was spread on a metal substrate, and cross sectional images of ultra violet ray were exposed. Through the layer by layer stacking, micro lattice structures with a diamond type periodic arrangement were successfully formed. The composite structures could be obtained through the dewaxing and sintering process with the lower temperature under the transition point of metallic glass. Transmission spectra of the terahertz waves through the magnetophotonic crystals were measured by using a terahertz time domain spectroscopy.

Linear Optical Properties of Zinc Borotellurite Glass Doped with Lanthanum Oxide Nanoparticles for Optoelectronic and Photonic Application

Directory of Open Access Journals (Sweden)

Faznny Mohd Fudzi

2017-01-01

Full Text Available Enhancing the optical properties of glasses for the sake of optical application in various fields is an ongoing challenge in materials science and technology. Thus, the optical properties of zinc borotellurite glass doped with lanthanum oxide nanoparticles (La2O3 NPs with the chemical composition of {[(TeO20.7(B2O30.3]0.7(ZnO0.3}1−x (La2O3 NPsx, where x = 0.01, 0.02, 0.03, 0.04, and 0.05 molar fraction, have been investigated. Characterization techniques such as x-ray diffraction, Fourier Transform Infrared Spectroscopy, and Ultraviolet-Visible Spectroscopy are employed to yield the structural properties and optical parameter of the glass. The amorphous nature of the fabricated glasses is confirmed with the presence of a broad hump via XRD diffraction pattern. The decreasing amount of high polarizable nonbridging oxygen as the concentration of La2O3 NPs increases has contributed to the increasing trend of energy band gap in the range of 2.70 to 3.52 eV and decreasing value of refractive index between 2.34 and 2.48. The fabricated glasses that have a higher refractive index than the widely used fiber material, pure silica glass, indicate that zinc borotellurite glass doped with lanthanum nanoparticles is a promising material to be applied as optical fibers.

Freezing of aluminium oxide and iron flowing upward in circular quartz glass tubes

International Nuclear Information System (INIS)

Kuhn, D.; Moeschke, M.; Werle, H.

1983-10-01

The freezing of aluminium oxide and iron flowing upward in circular quartz glass tubes has been studied in a series of experiments. Several tubes were used in the same test. This demonstrated a good reproducibility and allowed systematic parameter variations, especially of the channel diameter. The time-dependance of the penetration was observed with a film camera and these date provide a good basis for a detailed check of sophisticated models which are in development. (orig.) [de

All-nanoparticle self-assembly ZnO/TiO₂ heterojunction thin films with remarkably enhanced photoelectrochemical activity.

Science.gov (United States)

Yuan, Sujun; Mu, Jiuke; Mao, Ruiyi; Li, Yaogang; Zhang, Qinghong; Wang, Hongzhi

2014-04-23

The multilaminated ZnO/TiO2 heterojunction films were successfully deposited on conductive substrates including fluorine-doped tin oxide (FTO) glass and flexible indium tin oxide coated poly(ethylene terephthalate) via the layer-by-layer (LBL) self assembly method from the oxide colloids without using any polyelectrolytes. The positively charged ZnO nanoparticles and the negatively charged TiO2 nanoparticles were directly used as the components in the consecutive deposition process to prepare the heterojunction thin films by varying the thicknesses. Moreover, the crystal growth of both oxides could be efficiently inhibited by the good connection between ZnO and TiO2 nanoparticles even after calcination at 500 °C, especially for ZnO which was able to keep the crystallite size under 25 nm. The as-prepared films were used as the working electrodes in the three-electrode photoelectrochemical cells. Because the well-contacted nanoscale heterojunctions were formed during the LBL self-assembling process, the ZnO/TiO2 all-nanoparticle films deposited on both substrates showed remarkably enhanced photoelectrochemical properties compared to that of the well-established TiO2 LBL thin films with similar thicknesses. The photocurrent response collected from the ZnO/TiO2 electrode on the FTO glass substrate was about five times higher than that collected from the TiO2 electrode. Owing to the absence of the insulating layer of dried polyelectrolytes, the ZnO/TiO2 all-nanoparticle heterojunction films were expected to be used in the photoelectrochemical device before calcination.

Physical activity attenuates the influence of FTO variants on obesity risk: a meta-analysis of 218,166 adults and 19,268 children.

Directory of Open Access Journals (Sweden)

Tuomas O Kilpeläinen

2011-11-01

Full Text Available The FTO gene harbors the strongest known susceptibility locus for obesity. While many individual studies have suggested that physical activity (PA may attenuate the effect of FTO on obesity risk, other studies have not been able to confirm this interaction. To confirm or refute unambiguously whether PA attenuates the association of FTO with obesity risk, we meta-analyzed data from 45 studies of adults (n = 218,166 and nine studies of children and adolescents (n = 19,268.All studies identified to have data on the FTO rs9939609 variant (or any proxy [r(2>0.8] and PA were invited to participate, regardless of ethnicity or age of the participants. PA was standardized by categorizing it into a dichotomous variable (physically inactive versus active in each study. Overall, 25% of adults and 13% of children were categorized as inactive. Interaction analyses were performed within each study by including the FTO×PA interaction term in an additive model, adjusting for age and sex. Subsequently, random effects meta-analysis was used to pool the interaction terms. In adults, the minor (A- allele of rs9939609 increased the odds of obesity by 1.23-fold/allele (95% CI 1.20-1.26, but PA attenuated this effect (p(interaction  = 0.001. More specifically, the minor allele of rs9939609 increased the odds of obesity less in the physically active group (odds ratio  = 1.22/allele, 95% CI 1.19-1.25 than in the inactive group (odds ratio  = 1.30/allele, 95% CI 1.24-1.36. No such interaction was found in children and adolescents.The association of the FTO risk allele with the odds of obesity is attenuated by 27% in physically active adults, highlighting the importance of PA in particular in those genetically predisposed to obesity.

Analysis of SNPs of MC4R , GNB3 and FTO gene polymorphism in ...

African Journals Online (AJOL)

Analysis of SNPs of MC4R , GNB3 and FTO gene polymorphism in obese Saudi subjects. Said Salama Moselhy, Yasmeen A Alhetari, Archana Iyer, Etimad A Huwait, Maryam A AL-Ghamdi, Shareefa AL-Ghamdi, Khadijah Saeed Balamash, Ashraf A Basuni, Mohamed N Alama, Taha A Kumosani, Soonham Sami Yaghmoor ...

Optical properties of alkaline earth borate glasses

African Journals Online (AJOL)

user

The alkaline earth borate glasses containing heavy metal oxides show good solubility of rare-earth ions. Glasses containing PbO exhibit low glass transition temperature (Tg) and high ..... These oxygen ions carry a partial negative charge and.

Fat Mass and Obesity-Associated (FTO) Gene Polymorphisms Are Associated with Physical Activity, Food Intake, Eating Behaviors, Psychological Health, and Modeled Change in Body Mass Index in Overweight/Obese Caucasian Adults

OpenAIRE

Harbron, Janetta; Merwe, Lize van der; Zaahl, Monique; Kotze, Maritha; Senekal, Marjanne

2014-01-01

The fat mass and obesity-associated (FTO) gene is currently recognized as the most robust predictor of polygenic obesity. We investigated associations between the FTO rs1421085 and rs17817449 polymorphisms and the FTO rs1421085–rs17817449 haplotype and dietary intake, eating behavior, physical activity, and psychological health, as well as the effect of these associations on BMI. N = 133 treatment seeking overweight/obese Caucasian adults participated in this study. Genotyping was performed ...

Influence of processing conditions on the glass-crystal transition into borosilicate glasses

Energy Technology Data Exchange (ETDEWEB)

Deschanels, X.; Cachia, J.N.; Lopez, C.; Peuget, S. [CEA Marcoule, BP 17171, 30207 Bagnols sur Ceze (France)

2008-07-01

The precipitation of a crystalline phase in glass is observed when one element exceeds its loading limit (i.e.: solubility limit). In this work we have studied the solubility of different actinides and surrogates (lanthanides and hafnium) in borosilicate glass used for the immobilization of the high-level nuclear waste (HLW glasses). The results obtained show an increase of the solubility limits of these elements with the processing temperature and the redox potential of the melt. The elements at the oxidation state (III) exhibit a higher solubility than the element at oxidation state (IV). In this framework, cerium is an interesting element because its oxidation state tunes from (IV) to (III) as a function of the processing conditions. It is shown that the solubility of cerium can be multiplied by a factor of 20 at 1100 C. degrees. In order to have a better understanding of the mechanisms that underline the evolution of the solubility, XAFS and NMR investigation has been undertaken. Trivalent elements present the characteristics of network-modified cations while tetravalent elements look like network-former cations.

Glass Composition for the use as a Sealant

DEFF Research Database (Denmark)

2014-01-01

The invention concerns a glass composition for the use as a sealant, particularly in a solid oxide fuel cell (SOFC) or in a solid oxide electrolyser cell (SOEC). The glass composition comprises 35-70 mol% CaO, 5-45 mol% ZnO, 5-50 mol% B2O3, 1-45 mol% SiO2, and 1 mol% or less of each element...... of the group, comprising Ba, Na and Sr, based on the total glass composition. Furthermore, the invention relates to an SOFC and an SOEC employing a sealant of said glass composition....

Enhancement of open-circuit voltage on organic photovoltaic devices by Al-doped TiO{sub 2} modifying layer produced by sol–gel method

Energy Technology Data Exchange (ETDEWEB)

Valaski, R.; Arantes, C.; Senna, C.A.; Carôzo, Victor; Achete, C.A. [Materials Metrology Division, Instituto Nacional de Metrologia, Qualidade e Tecnologia, Xerém, Duque de Caxias 25250-020, RJ (Brazil); Cremona, M., E-mail: cremona@fis.puc-rio.br [Materials Metrology Division, Instituto Nacional de Metrologia, Qualidade e Tecnologia, Xerém, Duque de Caxias 25250-020, RJ (Brazil); Physics Department, Pontifícia Universidade Católica do Rio de Janeiro, Rio de Janeiro 22453-970, RJ (Brazil)

2014-12-01

Sol–gel method has shown several advantages for oxide synthesis, such as lower cost production, coating large areas, lower processing temperatures and ease insertion of doping materials. Therefore, it is attractive for production of intermediate and electrode modifying layers in organic optoelectronic devices. Herein, spin-coated aluminum-doped titanium dioxide (AlTiO{sub 2}) thin films were produced by sol–gel method onto glass and fluorine-doped tin oxide (FTO) substrates, using different Al-dopant concentrations and post-done annealing temperatures. Electrical measurements were performed in order to investigate the improvement of the TiO{sub 2} resistivity. Additionally, structural, compositional, morphological, optical and electrical properties of the optimal AlTiO{sub 2} modifying layers onto FTO substrates were probed by different techniques, and compared with those obtained from the undoped thin films produced under similar conditions. Organic photovoltaic devices (OPVs) with the structure FTO/AlTiO{sub 2}(30 nm)/C{sub 60}(50 nm)/CuPc(50 nm)/Al with an Al concentration of 0.03 M in AlTiO{sub 2} layer were produced. The insertion of AlTiO{sub 2} thin films improved the short-circuit current density (J{sub sc}) as well as the open circuit voltage (V{sub oc}) in comparison with non-modified electrode FTO based devices. This behavior is discussed in terms of induced interface phenomena as dipole formation induced by Al. - Highlights: • Easy and cheap solution-process for AlTiO{sub 2} modification of FTO electrode for OPVs • Electrical, structural and optical characterization of TiO{sub 2} layers with Al-dopant • Improvement of Voc and Jsc of inverted OPVs with AlTiO{sub 2} modified electrode.

Iron and manganese in oxide minerals and in glasses: preliminary consideration of Eh buffering potential at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Caporuscio, F.A.; Vaniman, D.T.

1985-04-01

The tuffs of Yucca Mountain at the Nevada Test Site are currently under investigation as a possible deep burial site for high-level radioactive waste disposal. One of the main concerns is the effect of oxidizing groundwater on the transport of radionuclides. Rock components that may affect the oxygen content of groundwater include Fe-Ti oxides, Mn oxides, and glasses that contain ferrous iron. Some phenocryst Fe-Ti oxides at Yucca Mountain are in reduced states, whereas groundmass Fe-Ti oxides have been oxidized to hematite, rutile, and pseudobrookite (Fe 3+ -bearing phases) exclusively. Estimates of Fe 2+ -bearing oxides indicate that less than 0.33 vol% phenocrysts is available to act as solid buffering agents of Eh. Of this percentage, significant amounts of Fe-Ti oxides are isolated from effective interaction with groundwater because they occur in densely welded, devitrified tuffs that have low interstitial permeability. Manganese oxides occur primarily along fractures in the ash-flow tuffs. Because the Mn oxides are concentrated along the same pathways (fractures) where transport has occurred in the past, these small volume percentages could act as buffers. However, the oxidation states of actual Mn-oxide phases are high (Mn 4+ ), and these minerals have virtually no potential for reducing groundwater Eh. Manganese oxides may even act as oxidizing agents. However, regardless of their poor capabilities as reducing agents, the Mn oxides could be important as sorbents of heavy metals at Yucca Mountain. The lack of accessible, pristine Fe-Ti oxides and the generally high oxidation states of Mn oxides seem to rule out these oxides as Eh buffers of the Yucca Mountain groundwater system. Reduction of ferrous iron within glassy tuffs may have some effect on Eh, but further study is needed. At present it is prudent to assume that minerals and glasses have little or no capacity for reducing oxygen-rich groundwater at Yucca Mountain. 25 refs., 3 figs., 12 tabs

Multifunctionality in epoxy/glass fibers composites with graphene interphase

OpenAIRE

Mahmood, Haroon

2017-01-01

In this project, the synergetic effect of a graphene interphase in epoxy/glass fibers composites was investigated by coating glass fibers (GF) with graphene oxide (GO) and reduced graphene oxide (rGO) nanosheets by an electrophoretic deposition (EPD) technique. Graphite oxide was prepared using modified Hummers method in which raw graphite powder was oxidized using potassium permanganate (KMnO4) in acidic solution. Using ultrasonic technique, the graphite oxide was dispersed homogenously in w...

Indium oxide deposition on glass by aerosol pyrolysis (Pyrosol (R) process)

International Nuclear Information System (INIS)

Blandenet, G.; Lagarde, Y.; Spitz, J.

1975-01-01

The pyrosol (R) process involves the pyrolysis of an aerosol generated by ultrasonic nebulisation from a solution of organic or inorganic compounds. This technique was used to deposit transparent n-conducting indium oxide films on glass. The electrical and optical properties of these films were studied as a function of the deposition temperature and doping (using tin or fluorine). A deposition temperature of 480 deg C and a Sn/In ratio of about 5% gave the best results. In this case, the transmission in the visible range was 92%, the infrared reflection 84% and the electrical resistivity 1.7x10 -4 ohm.cm [fr

Oxycarbonitride glass formation by melt solidification

Energy Technology Data Exchange (ETDEWEB)

Imon, M M; Risbud, S H

1986-04-01

Experimental results are presented from the synthesis and characterization of multianion oxycarbonitride glasses composed of MgSiAlON glass powders with SiC additions of 5, 10, or 15 wt pct. Nitrogen additions to the oxide MgO-Al2O3-SiO2 glasses increased devitrification resistance, but carbon additions to MgSiAlON glasses promote crystal nucleation. These properties are relevant to the oxycarbonitride glasses use in refractory glass-ceramic and ceramic-ceramic composite systems with good elevated temperature performance. 9 references.

Predicting the glass transition temperature of bioactive glasses from their molecular chemical composition.

Science.gov (United States)

Hill, Robert G; Brauer, Delia S

2011-10-01

A recently published paper (M.D. O'Donnell, Acta Biomaterialia 7 (2011) 2264-2269) suggests that it is possible to correlate the glass transition temperature (T(g)) of bioactive glasses with their molar composition, based on iterative least-squares fitting of published T(g) data. However, we show that the glass structure is an important parameter in determining T(g). Phase separation, local structural effects and components (intermediate oxides) which can switch their structural role in the glass network need to be taken into consideration, as they are likely to influence the glass transition temperature of bioactive glasses. Although the model suggested by O'Donnell works reasonably well for glasses within the composition range presented, it is oversimplified and fails for glasses outside certain compositional boundaries. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

The far infrared radiation characteristics for Li2O.Al2O3.4SiO2(LAS) glass-ceramics and transition-metal oxide

International Nuclear Information System (INIS)

Huh, Nam Jung; Yang, Joong Sik

1991-01-01

The far infrared radiation characteristic for Li 2 O.Al 2 O 3 .4SiO 2 (LAS) glass, the LAS glass-ceramic and sintered transition metal oxides such as CuO, Fe 2 O 3 and Co 3 O 4 , were investigated. LAS glass and LAS glass-ceramic was higher than that of the LAS glass. Heat-treated CuO and Co 3 o 4 had radiation characteristic of high efficiency infrared radiant, and heat-treated Fe 2 O 3 had radiation characteristic that infrared emissivity decreased in higher was length above 15μm. (Author)

Sulphate solubility and sulphate diffusion in oxide glasses: implications for the containment of sulphate-bearing nuclear wastes

International Nuclear Information System (INIS)

Lenoir, M.

2009-09-01

The thesis deals with sulphate solubility and sulphate diffusion in oxide glasses, in order to control sulphate incorporation and sulphate volatilization in nuclear waste glasses. It was conducted on simplified compositions, in the SiO 2 -B 2 O 3 -R 2 O (R = Li, Na, K, Cs), SiO 2 -B 2 O 3 -BaO and V 2 O 5 -B 2 O 3 -BaO systems. These compositions allowed us to study the influence of the nature of network-modifying ions (Li + , Na + , K + , Cs + or Ba 2+ ) and also of former elements (Si, B, V), on structure and properties of glasses. Sulphate volatility is studied in sodium borosilicate melts using an innovative technique of sulphate quantitation with Raman spectroscopy. This technique is useful to obtain kinetic curves of sulphate volatilization. The establishment of a model to fit these curves leads to the determination of diffusion coefficients of sulphate. These diffusion coefficients can thus be compared to diffusion coefficients of other species, determined by other techniques and presented in the literature. They are also linked to diffusion coefficients in relation with the viscosity of the melts. Concerning sulphate solubility in glasses, it depends on glass composition and on the nature of sulphate incorporated. Sulphate incorporation in alkali borosilicate glasses leads to the formation of a sulphate layer floating on top of the melt. Sulphate incorporation in barium borosilicate and boro-vanadate glasses leads to the crystallization of sulphate species inside the vitreous matrix. Moreover, sulphate solubility is higher in these glasses than in alkali borosilicates. Finally, exchanges between cations present in glasses and cations present in the sulphate phase are also studied. (author)

Glass enamel and glass-ceramic coatings for chemical apparatus

International Nuclear Information System (INIS)

Es'kov, A.S.; Oleinik, M.I.; Shabrova, E.A.

1984-01-01

Among the known anticorrosion coatings used in chemical engineering, glass enamel base coatings are distinguished by such advantages as a high degree of continuity and chemical resistance. The paper describes basic principles for the creation of acid and alkali resistant glass enamel and ceramic coatings for chemical apparatus. As the result of investgations, glass enamel coatings with increased electrical conductivity and also experimental production compositions of chemical, temperature and radiation resistant coatings for protection of chemical equipment of 12Kh18N10T stainless steel have been developed. The coatings have successfully passed testing under service conditions. A new type of coating is short-term glass enamel, which may be recommended for use in chemical machinery manufacturing and other branches of industry in oxidation-free heating and forming of stainless steels

The borosilicate glass for 'PAMELA'

International Nuclear Information System (INIS)

Schiewer, E.

1986-01-01

The low enriched waste concentrate (LEWC) stored at Mol, Belgium, will be solidified in the vitrification plant 'PAMELA'. An alkali-borosilicate glass was developed by the Hahn-Meitner-Institut, Berlin, which dissolves (11 +- 3)wt% waste oxides while providing sufficient flexibility for changes in the process parameters. The development of the glass labelled SM513LW11 is described. Important properties of the glass melt (viscosity, resistivity, formation of yellow phase) and of the glass (corrosion in aqueous solutions, crystallization) are reported. The corrosion data of this glass are similar to those of other HLW-glasses. Less than five wt% of crystalline material are produced upon cooling of large glass blocks. Crystallization does not affect the chemical durability. (Auth.)

Wetting and surface tension of bismate glass melt

International Nuclear Information System (INIS)

Shim, Seung-Bo; Kim, Dong-Sun; Hwang, Seongjin; Kim, Hyungsun

2009-01-01

Lead oxide glass frits are used widely in the electronics industry for low-temperature firing. On the other hand, one of the low-sintering and low-melting lead-free glass systems available, the bismate glass system, is considered to be an alternative to lead oxide glass. In order to extend the applications of Bi 2 O 3 glasses, this study examined the thermophysical properties of low-melting Bi 2 O 3 -B 2 O 3 -ZnO-BaO-Al 2 O 3 -SiO 2 glass frits with various ZnO/B 2 O 3 ratios. The fundamental thermal properties, such as glass transition temperature and softening point, were examined by differential thermal analysis and a glass softening point determination system. The wetting angles, viscosities and surface tension of the various bismate glasses on an alumina substrate were measured using hot-stage microscopy and the sessile drop method. These thermophysical properties will be helpful in understanding the work of adhesion and the liquid spread kinetics of glass frits.

Influence of the sintering temperature in the microstructure of foam glass obtained from waste glass

International Nuclear Information System (INIS)

Pokorny, A.; Vicenzi, J.; Bergmann, C.P.

2012-01-01

In this work, foam glasses were produced from grounded soda-lime glass and a synthetic carbonate, used as a foaming agent, with a similar composition to a dolomite lime, added with different oxides (SiO 2 , Al 2 O 3 , Fe 2 O 3 , MnO 2 , Na 2 O, K 2 O, TiO 2 and P 2 O 5 ). The objective was to evaluate the influence of sintering temperature on the properties and microstructure of the obtained material. In addition, the effect of addition of the oxides in the expansion of the ceramic bodies was evaluated. The ceramic bodies were formulated with 3 weight percent of synthetic carbonate, uniaxially pressed and fired within the temperature range from 700 deg C to 950 deg C, with a heating rate of 150K/h. The technological characterization of the ceramic bodies involved the determination of the volumetric expansion and their microstructures have been characterized by optical microscopy and scanning electron microscopy. The experimental results have shown foam glass can be obtained from grounded soda-lime glass, using synthetic carbonate, with the introduction of the different oxides, as foaming agent. (author)

New Er{sup 3+} doped antimony oxide based glasses: Thermal analysis, structural and spectral properties

Energy Technology Data Exchange (ETDEWEB)

Ouannes, K. [Faculté des Sciences et de la Technologie, Université de Biskra, BP 145 RP, 07000, Biskra (Algeria); Lebbou, K., E-mail: kheirreddine.lebbou@univ-lyon1.fr [Institut Lumière Matière, UMR5306 Université Lyon 1-CNRS, Université de Lyon, 69622, Villeurbanne (France); Walsh, Brian-M. [NASA Langley Research Center, Hampton, VA, 23681 (United States); Poulain, M. [UMR 6226- Verres et Céramiques – Campus de Beaulieu, Université de Rennes1, 35042, Rennes (France); Alombert-Goget, G.; Guyot, Y. [Institut Lumière Matière, UMR5306 Université Lyon 1-CNRS, Université de Lyon, 69622, Villeurbanne (France)

2015-11-15

The novel oxide glass compositions based on Sb{sub 2}O{sub 3} are elaborated and characterized, in the system (90-X)Sb{sub 2}O{sub 3}–10Na{sub 2}O–XBi{sub 2}O{sub 3} (SNB). We are interested in bismuth rates incorporated into the glass, its effect on the different physical properties that have been measured, and especially, in radiative and spectroscopic properties of erbium doped SNB glasses. Differential scanning calorimeter (DSC) measurements show an improvement of the stability factor,ΔT, of the glasses, which can indicate a reinforcement of the network. Both FTIR and Raman spectra have also been considered in terms of bismuth influence. As a function of composition, we have principally measured optical absorption, visible and infrared emission, and lifetime. The Judd–Ofelt parameters measured from the absorption spectra have been used to calculate the radiative lifetime (τ{sub r}) and the stimulated emission cross section. The spectroscopic quality factor χ = Ω{sub 4}/Ω{sub 6} = 0.73, low phonon energy of ∼600–700 cm{sup −1}, a reduced quenching effect, and a high quantum efficiency of 90% for the 1.53 μm measured emission, by pumping at 980 nm, are in favor of promising laser applications. - Highlights: • Glass belonging to Er-doped Sb{sub 2}O{sub 3}–Na{sub 2}O–Bi{sub 2}O{sub 3} (SNB) system are elaborated and characterized. • The intensity parameters Ωt were obtained via the Judd–Ofelt theory. • The optical properties were studied as a function of glass composition.

Photoluminescence and semiconducting behavior of Fe, Co, Ni and Cu implanted in heavy metal oxide glasses

Directory of Open Access Journals (Sweden)

Mohamed A. Marzouk

2016-07-01

Full Text Available Transition metal ions (0.5 wt% of Fe2O3, CoO, NiO or CuO doped heavy metal oxide glasses having chemical composition of 60PbO·20Bi2O3·20 MxOy mol% (where MxOy = B2O3 or SiO2 or P2O5 were prepared by conventional melt annealing method. Combined optical and photoluminescence properties have been measured and employed to evaluate the prepared glassy samples. From the absorption edge data, the values of the optical band gap Eopt, Urbach energy (ΔE and refractive index were calculated to estimate semiconducting behavior. Photoluminescence and values of the optical energy gap were found to be dependent on the glass composition. The variations of the photoluminescence intensity, values of optical band gap, Urbach energy and refractive index gave an indication to use the prepared glasses for design of novel functional optical materials with higher optical performance.

Stable glass-ceramic sealants for solid oxide fuel cells: Influence of Bi{sub 2}O{sub 3} doping

Energy Technology Data Exchange (ETDEWEB)

Goel, Ashutosh; Ferreira, Jose M.F. [Department of Ceramics and Glass Engineering, University of Aveiro, CICECO, 3810-193 Aveiro (Portugal); Pascual, Maria J. [Instituto de Ceramica y Vidrio (CSIC), Kelsen 5, Campus de Cantoblanco, 28049 Madrid (Spain)

2010-07-15

Diopside (CaMgSi{sub 2}O{sub 6}) based glass-ceramics in the system SrO-CaO-MgO-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}-La{sub 2}O{sub 3}-Bi{sub 2}O{sub 3}-SiO{sub 2} have been synthesized for sealing applications in solid oxide fuel cells (SOFC). The parent glass composition in the primary crystallization field of diopside has been doped with different amounts of Bi{sub 2}O{sub 3} (1, 3, 5 wt.%). The sintering behavior by hot-stage microscopy (HSM) reveals that all the investigated glass compositions exhibit a two-stage shrinkage behavior. The crystallization kinetics of the glasses has been studied by differential thermal analysis (DTA) while X-ray diffraction adjoined with Rietveld-R.I.R. analysis have been employed to quantify the amount of crystalline and amorphous phases in the glass-ceramics. Diopside and augite crystallized as the primary crystalline phases in all the glass-ceramics. The coefficient of thermal expansion (CTE) of the investigated glass-ceramics varied between (9.06-10.14) x 10{sup -6} K{sup -1} after heat treatment at SOFC operating temperature for a duration varying between 1 h and 200 h. Further, low electrical conductivity, good joining behavior and negligible reactivity with metallic interconnects (Crofer22 APU and Sanergy HT) in air indicate that the investigated glass-ceramics are suitable candidates for further experimentation as sealants in SOFC. (author)

FTO variant rs9939609 is associated with body mass index and waist circumference, but not with energy intake or physical activity in European- and African-American youth

Directory of Open Access Journals (Sweden)

Dong Yanbin

2010-04-01

Full Text Available Abstract Background Genome-wide association studies found common variants in the fat mass and obesity-associated (FTO gene associated with adiposity in Caucasians and Asians but the association was not confirmed in African populations. Association of FTO variants with insulin resistance and energy intake showed inconsistent results in previous studies. This study aimed to assess the influence of FTO variant rs9939609 on adiposity, insulin resistance, energy intake and physical activity in European - (EA and African-American (AA youth. Methods We conducted a cross-sectional study in EA and AA youths. One thousand, nine hundred and seventy-eight youths (48.2% EAs, 47.1% male, mean age 16.5 years had measures of anthropometry. Percent body fat (%BF was measured by dual-energy X-ray absorptiometry, visceral adipose tissue (VAT and subcutaneous abdominal adipose tissue (SAAT by magnetic resonance imaging. Energy intake and physical activity were based on self report from up to 7 24-hour recalls. Physical activity was also measured by accelerometry. Results FTO rs9939609 was significantly associated with body mass index (BMI (P = 0.01, weight (P = 0.03 and waist circumference (P = 0.04, with per-allele effects of 0.4 kg/m2, 1.3 kg and 0.8 cm, respectively. No significant association was found between rs9939609 and %BF, VAT, SAAT or insulin resistance (P > 0.05, or between rs9939609 and energy intake or vigorous physical activity (P > 0.05. No significant interactions of rs9939609 with ethnicity, gender, energy intake or physical activity were observed (P > 0.05. Conclusions The FTO variant rs9939609 is modestly associated with BMI and waist circumference, but not with energy intake or physical activity. Moreover, these effects were similar for EAs and AAs. Improved understanding of the effect of the FTO variant will offer new insights into the etiology of excess adiposity.

Iron oxide coating films in soda-lime glass by triboadhesion

Energy Technology Data Exchange (ETDEWEB)

Aguilar, J. O.; Arjona, M. J. [Boulevard Bahia s/n esq. Ignacio Comonfort, Chetumal (Mexico); Rodriguez-Lelis, J. M. [Interior Internado Palmira s/n, Cuernavaca, Morelos (Mexico)

2009-04-15

In the triboadhesion process the coating material is passed through a rotating cotton mop and the substrate to be coated. The cotton mop rotates at high velocity and exerts pressure on the surface of the substrate. The combined effect of pressure and velocity of the coating mop on the substrate increases its temperature close to the melting point, allowing deposition and diffusion of the coating material within the substrate. After it is deposited, its particles are embedded within the base material forming a thin film composite. The amount of the coating material deposited on the substrate has its maximum at the surface and then decreases as a function of the local temperature within the base material. Bearing this in mind, in the present work, triboadhesion is employed to deposit iron oxide in a substrate of soda-lime glass, with the purpose of determining the feasibility of using this technique for solar control coatings. It was found, through electronic scan microscopy, that a composite material film is formed following the coating direction. Reflectance and transmittance tests were carried out on the glass samples. A 20% difference was found in the visible spectral region (VIS), and a reduction between 10 and 20% in the Near Infrared Region (NIR). These results showed that the triboadhesion is a promising technique for the application of thin films for solar control or solar cells

Iron oxide coating films in soda-lime glass by triboadhesion

International Nuclear Information System (INIS)

Aguilar, J. O.; Arjona, M. J.; Rodriguez-Lelis, J. M.

2009-01-01

In the triboadhesion process the coating material is passed through a rotating cotton mop and the substrate to be coated. The cotton mop rotates at high velocity and exerts pressure on the surface of the substrate. The combined effect of pressure and velocity of the coating mop on the substrate increases its temperature close to the melting point, allowing deposition and diffusion of the coating material within the substrate. After it is deposited, its particles are embedded within the base material forming a thin film composite. The amount of the coating material deposited on the substrate has its maximum at the surface and then decreases as a function of the local temperature within the base material. Bearing this in mind, in the present work, triboadhesion is employed to deposit iron oxide in a substrate of soda-lime glass, with the purpose of determining the feasibility of using this technique for solar control coatings. It was found, through electronic scan microscopy, that a composite material film is formed following the coating direction. Reflectance and transmittance tests were carried out on the glass samples. A 20% difference was found in the visible spectral region (VIS), and a reduction between 10 and 20% in the Near Infrared Region (NIR). These results showed that the triboadhesion is a promising technique for the application of thin films for solar control or solar cells

Electrochromic and electrochemical capacitive properties of tungsten oxide and its polyaniline nanocomposite films obtained by chemical bath deposition method

CSIR Research Space (South Africa)

Nwanya, AC

2014-05-01

Full Text Available Polyanine and its nanocomposite WO3/PANI films were deposited on fluorine doped tin oxide (FTO) glassslides by simple chemical bath deposition method. The morphology structure of the composite film wasstudied using atomic force microscopy (AFM...

Fundamental problems on immiscibility, crystallization, and chemical interaction between stainless steel 304 and glasses for radioactivewaste glasses

International Nuclear Information System (INIS)

Inoue, Tadashi; Yokoyama, Hayaichi

1982-01-01

Immiscibility and crystallization, and chemical interaction with stainless steel, SUS 304, which is designed as a canister material, were investigated on non-radioactive glasses with simulated waste of 26.4 wt%. Although glasses whose initial color was black changed to yellow or yellow-brown by heat-treatment at 600 0 C, the change of color was hardly observed by the treatment at 850 0 C. Molybdenum oxide and molybdate were detected in all heat-treated glasses. It was deduced that the compounds were existing as meta-stable particle corresponding to immiscibility particle at 600 0 C and as stable crystallized particle at 850 0 C. The chemical interaction occurred at the interface between glasses and SUS 304, whose surface was attacked by boundary corrosion proceeding to uniform corrosion with increasing temperature and time. Chromium oxide layer was mainly formed in the region suffered chemical interaction. It was deduced that the chemical interaction was moderated due to the formation of protective layer, which mainly consisted of nickel oxide, at the same time as the formation of Cr 2 O 3 layer. (author)

Thermoluminescence properties of alkali borate glasses containing neodymium

Energy Technology Data Exchange (ETDEWEB)

Abbas, A.F.; Henaish, B.A.; Kenaway, M.A.; Salem, L.R.

1988-01-01

The thermoluminescence properties of sodium borate glasses as a function of neodymium oxide content as well as the divalent metal oxides (RO = ZnO, MgO and CaO) in replacement of Na/sub 2/O have been investigated. It is observed that the addition of Nd/sub 2/O/sub 3/ imparts to the host glass a monopeak glow curve according to an active luminescent centre (E approx. = 0.97 eV to 1.232 eV). The gradual addition of neodymium oxide to the sodium borate glass causes gradual enhancement in the TL-intensity up to a quenching concentration value (4 g Nd/sub 2/O/sub 3/ added to 100 g of borate glass) above which a draw back in TL-intensity occurs. On the other hand the replacement of 5 wt% Na/sub 2/O by RO shows that CaO dominates the other two divalent metal oxides used, as it possesses a much deeper luminescent trap (1.232 eV). The results obtained suggest that these glasses can be used in radiation detection and dosimetry. The ..gamma..-induced Tl-signal of such type of glass is found to be reproducible within an acceptable error of not more than 3.5% in all individual and group scattering over the detector samples each of which is used 10 times for evaluating the same ..gamma..-dose.

The directed preparation of TiO2 nanotubes film on FTO substrate via hydrothermal method for gas sensing application

Directory of Open Access Journals (Sweden)

Pham Van Viet

2016-04-01

Full Text Available In this research, we directly synthesized TiO2 nanotubes film on Fluorine doped Tin oxide (FTO substrate via hydrothermal method from commercial TiO2 in NaOH solution at 135 ℃ for 24 hours. The samples were characterized by X-ray diffraction (XRD pattern, field emission scanning electron microscopy (FESEM and transmitting electron microscopy (TEM. The average diameter of TiO2 nanotubes (TNTs is about 10–12 nm and their length is about a few hundred nanometers. The sensitivity ability of TNTs increases as the gas concentration increases and developing to the highest sensitivity of TNTs is 2.4 at 700 ppm of the ethanol concentration. The same as the gas concentration, the sensitivity of TNTs increases when the temperature increases. Besides, the sensitivity of samples at 250 ℃ is doubled compared to samples determined at 100 ℃.

Electrochemical reaction rates in a dye-sensitised solar cell - the iodide/tri-iodide redox system

DEFF Research Database (Denmark)

Bay, L.; West, K.; Winther-Jensen, B.

2006-01-01

The electrochemical reaction rate of the redox couple iodide/tri-iodide in acetonitrile is characterised by impedance spectroscopy. Different electrode materials relevant for the function of dye-sensitised solar cells (DSSC) are investigated. Preferably, the reaction with the iodide....../tri-iodide couple should be fast at the counter electrode, i.e. this electrode must have a high catalytic activity towards the redox couple, and the same reaction must be slow on the photo electrode. The catalytic activity is investigated for platinum, poly(3,4-ethylenedioxythiophene) (PEDOT), polypyrrole (PPy......), and polyaniline (PANI)-all deposited onto fluorine-doped tin oxide (FTO) glass. Both Pt and PEDOT are found to have sufficiently high catalytic activities for practical use as counter electrodes in DSSC. The reaction resistance on FTO and anatase confirmed the beneficial effect of a compact anatase layer on top...

Electrochemical reaction rates in a dye sentisised solar cell - the iodide/tri-iodide redox system

DEFF Research Database (Denmark)

Bay, Lasse; West, Keld; Winter-Jensen, Bjørn

2006-01-01

The electrochemical reaction rate of the redox couple iodide / tri-iodide in acetonitrile is characterised by impedance spectroscopy. Different electrode materials relevant for the function of dye-sensitised solar cells (DSSC) are investigated. Preferably, the reaction with the iodide / tri......-iodide couple should be fast at the counter electrode, i.e. this electrode must have a high catalytic activity towards the redox couple, and the same reaction must be slow on the photo electrode. The catalytic activity is investigated for platinum, poly(3,4-ethylenedioxythiophene) (PEDOT), polypyrrole (PPy......), and polyaniline (PANI) - all deposited onto fluorine doped tin oxide (FTO) glass. Both Pt and PEDOT are found to have sufficiently high catalytic activities for practical use as counter electrode in DSSC. The reaction resistance on FTO and anatase confirmed the beneficial effect of a compact anatase layer on top...

Synchrotron Micro-XANES Measurements of Vanadium Oxidation State in Glasses as a Function of Oxygen Fugacity: Experimental Calibration of Data Relevant to Partition Coefficient Determination

Science.gov (United States)

Delaney, J. S.; Sutton, S. R.; Newville, M.; Jones, J. H.; Hanson, B.; Dyar, M. D.; Schreiber, H.

2000-01-01

Oxidation state microanalyses for V in glass have been made by calibrating XANES spectral features with optical spectroscopic measurements. The oxidation state change with fugacity of O2 will strongly influence partitioning results.

The study of the rs9939609 FTO gene polymorphism in association with obesity and the management of obesity in a Romanian cohort.

Science.gov (United States)

Ursu, R I; Badiu, C; Cucu, N; Ursu, G F; Craciunescu, I; Severin, E

2015-01-01

The incidence of obesity especially in Romanian population is presently escalating as a major nutrition and health problem. Clinicians aided by scientists are engaged in research approaches that include heredity aspects linked with behavior, education, applied nutrition studies and clinical therapies in order to prevent, control and reverse obesity. The common goal is to identify areas of basic and clinical research to understand aspects of human biology that may be considered as obesogenic. Regarding these approaches, recent discoveries in genetics, epigenetics and functional genomics, based on advancing technologies, are tools employed to prevent and treat obesity. The purpose of this article is to present the current knowledge of key components of the FTO gene role in the obesogenic system that links genetic, epigenetic and environmental, lifestyle/ diet nutritional and behavioral components and to describe the results obtained by genotyping and interviewing relevant selected groups of Romanian population. FTO rs9939609 genotyping was performed on a Romanian study group of 53 subjects (30 obese, 23 normal). Results have been analyzed in association with obesity parameters and comorbidities in order to identify this polymorphism's effect on body mass in our Caucasian cohort. At the same time, personal history of the subjects in correlation with the FTO genotypes provided important information on the FTO gene's influence on the feeding behavior and food selection of these individuals. In conclusion, the FTO rs9939609 polymorphism has been identified as a common gene variant in our Romanian Caucasian cohort, proving a high association with all the parameters of obesity and obesity comorbidities. The adherence to a Mediterranean diet is benefic for subjects with genetic predisposition for this disorder as long as it is kept for a long period of time along with sustained physical exercise. Association studies are an extremely important tool in understanding the

Physical and spectroscopic studies of Cr{sup 3+} doped mixed alkaline earth oxide borate glasses

Energy Technology Data Exchange (ETDEWEB)

Samdani, E-mail: samdanimohd82@gmail.com [Department of Engineering, Salalah College of Technology, Salalah (Oman); Ramadevudu, G. [Department of Physics, Vasavi College of Engineering, Ibrahimbagh, Hyderabad 500031, Telangana (India); Chary, M. Narasimha; Shareefuddin, Md. [Department of Physics, Osmania University, Hyderabad 500007, Telangana (India)

2017-01-15

A series of mixed alkaline earth oxide glasses xMgO-(30-x)BaO-69.8B{sub 2}O{sub 3}-0.2Cr{sub 2}O{sub 3} were prepared and studied using electron paramagnetic resonance (EPR), optical absorption, Raman spectroscopy and photoluminescence experimental techniques. The optical absorption spectra revealed the characteristic octahedral symmetry of Cr{sup 3+}ions through three broad band transitions {sup 4}A{sub 2g}(F)→ {sup 4}T{sub 2g}(F), {sup 4}A{sub 2g}(F)→ {sup 4}T{sub 1g}(F), and {sup 4}A{sub 2g}(F)→ {sup 2}T{sub 1g}(P). The crystal field (Dq) and Racah parameters (B and C), the optical band gap and Urbach energies of the glass samples were also reported along with the physical properties like density and molar volume. In the EPR spectra three resonance signals corresponding to Cr3+ ions were observed. A broad signal with g = 5.110 was observed which belongs to the isolated Cr3+ centers localized in the strongly distorted octahedral (rhombic) sites of the glass network, a narrow signal (g = 1.960) corresponding to the Cr{sup 3+} centers in the weekly distorted (cubic) sites of the glass network, and a third very broad signal (g = 2.210) was also observed corresponding to Cr{sup 3+}- Cr{sup 3+} paired centers coupled by magnetic dipolar interaction. Another resonance signal with effective value g ≈ 4.220 was attributed to Fe{sup 3+} ions impurity. The number of spins (N) participating in the resonance and susceptibility (χ) values at room temperature were reported and their values varied in a non-linear manner with the composition exhibiting mixed oxide effect. The estimated molecular bonding coefficients (α) values indicated stronger ionic contribution. The Raman spectral investigations were carried out. The Photoluminescence spectra bands near 690 and 750 nm correspond to the Cr{sup 3+} centers in high and low field sites respectively. - Highlights: • Spectroscopic studies were made on alkaline earth borate glasses. • Three resonance signals

The effects of gamma irradiation on the elastic properties of soda lime glass doped with cerium oxide

Energy Technology Data Exchange (ETDEWEB)

Laopaiboon, R.; Laopaiboon, J.; Pencharee, S. [Glass Technology Excellent Center (GTEC), Department of Physics, Faculty of Science, Ubon Ratchathani University, Ubon Ratchathani, 34190 (Thailand); Nontachat, S. [Department of Radiotherapy, Ubon Ratchathani Cancer Centre, Ubon Ratchathani, 34190 (Thailand); Bootjomchai, C., E-mail: cherdsak_per@hotmail.co.th [Glass Technology Excellent Center (GTEC), Department of Physics, Faculty of Science, Ubon Ratchathani University, Ubon Ratchathani, 34190 (Thailand)

2016-05-05

Soda lime glass doped with cerium oxide was prepared using a conventional melt quenching technique. The density and molar volume of the glass samples were measured. Ultrasonic wave velocities of the glass samples were carried out using a pulse echo technique. The density and ultrasonic velocities were used for determining elastic moduli of the glass samples, both before and after irradiation with gamma rays at 1 kGy. The results revealed that the influence of gamma irradiation caused the matrix structure of the glass samples to be damaged by creating displacements, electronic defects and/or breaks in the network bonds, leading to the formation of non-bridging oxygens (NBOs). Elastic properties were investigated under the influence of gamma irradiation. The results also revealed that the structures of the glass samples were distorted by irradiation. Damage by irradiation created the NBOs and/or the transformation of main glass network structures from Q{sub 4} to Q{sub 3}. Evidence of these results was acquired from FTIR spectra. The results of FTIR supported the results and were obtained from ultrasonic velocities. In addition, the elastic properties obtained from experiments were compared with theoretical values calculated from the Makishima and Mackenzie model (M–M model). - Highlights: • Results show good agreement between experimental and theoretical of elastic moduli. • Influence of irradiation created a distorted network structure. • Transformation of network structure from Ref. Q{sub 4} to Q{sub 3} after irradiation. • FTIR result is good evidence of the result is obtained from ultrasonic technique.

Investigation of TLD properties of metal alloy oxides, glass, ceramics and various papers

International Nuclear Information System (INIS)

Erkol, A.Y.; Yasar, S.; Karakelle, B.; Yasar, D.

1995-01-01

A large number of materials exhibit radiothermoluminescence and they are extensively used for radiation process control. In this work, the thermoluminescence (TL) properties of metal alloy oxides, glass, ceramics and various papers are investigated in order to evaluate their possible usage as TL detectors or indicators in dose measurement. TL glow curves and the effect of absorbed dose on TL response are measured for materials locally available. The fading effect are also examined. The use of these materials as a dose indicator are shown to be promising. (author)

Investigation of TLD properties of metal alloy oxides, glass, ceramics and various papers

International Nuclear Information System (INIS)

Erkol, A.Y.; Yasar, S.; Karakelle, B.; Yasar, D.

1995-01-01

A large number of materials exhibit radiothermoluminescence and they are extensively used for radiation process control. In this work, the thermoluminescence (TL) properties of metal alloy oxides, glass, ceramics and various papers are investigated in order to evaluate their possible usage as TL detectors or indicators in dose measurement. TL glow curves and the effect of absorbed dose on TL response are measured for materials locally available. The fading effect is also examined. The use of these materials as a dose indicator is shown to be promising. (author)

Complete re-sequencing of a 2Mb topological domain encompassing the FTO/IRXB genes identifies a novel obesity-associated region upstream of IRX5

DEFF Research Database (Denmark)

Hunt, Lilian E; Noyvert, Boris; Bhaw-Rosun, Leena

2015-01-01

BACKGROUND: Association studies have identified a number of loci that contribute to an increased body mass index (BMI), the strongest of which is in the first intron of the FTO gene on human chromosome 16q12.2. However, this region is both non-coding and under strong linkage disequilibrium, making...... it recalcitrant to functional interpretation. Furthermore, the FTO gene is located within a complex cis-regulatory landscape defined by a topologically associated domain that includes the IRXB gene cluster, a trio of developmental regulators. Consequently, at least three genes in this interval have been...... implicated in the aetiology of obesity. METHODS: Here, we sequence a 2 Mb region encompassing the FTO, RPGRIP1L and IRXB cluster genes in 284 individuals from a well-characterised study group of Danish men containing extremely overweight young adults and controls. We further replicate our findings both...

Poly(3,4-ethylenedioxythiophene)/reduced graphene oxide composites as counter electrodes for high efficiency dye-sensitized solar cells

Science.gov (United States)

Ma, Jinfu; Yuan, Shenghua; Yang, Shaolin; Lu, Hui; Li, Yingtao

2018-05-01

A facile, low cost, easy-controllable method to prepare Poly(3,4-ethylenedioxythiophene) (PEDOT)/reduced graphene oxide (rGO) composites by electrochemical deposition onto fluorinated tin oxide (FTO) as counter electrodes (CEs) in high performance dye-sensitized solar cells (DSSCs) is reported. The electro-deposition process was accomplished by electro-polymerization of graphene oxide (GO)/PEDOT composites onto FTO substrates followed by electrochemical reduction of the GO component. Electrochemical measurements show that the I-/I3- catalytic activity of the as-prepared PEDOT/rGO CE is improved compared with that of the pure PEDOT and PEDOT/GO electrode. Through the analysis of photoelectric properties, the performance of the electrodes fabricated with different polymerization times are compared, and the optimal preparation condition is determined. The photoelectric conversion efficiency (PCE) of the DSSC assembled with PEDOT/rGO electrode reaches 7.79%, close to 8.33% of the cell with Platinum (Pt) electrode, and increases by 13.2% compared with 6.88% of the device with the PEDOT electrode.

Three-dimensionally embedded indium tin oxide (ITO) films in photosensitive glass: a transparent and conductive platform for microdevices

International Nuclear Information System (INIS)

Beke, S.; Sugioka, K.; Midorikawa, K.; Koroesi, L.; Dekany, I.

2011-01-01

A new method for embedding transparent and conductive two- and three-dimensional microstructures in glass is presented. We show that the internal surface of hollow structures fabricated by femtosecond-laser direct writing inside the photosensitive glass can be coated by indium tin oxide (Sn-doped In 2 O 3 , ITO) using a sol-gel process. The idea of combining two transparent materials with different electrical properties, i.e., insulating and conductive, is very promising and hence it opens new prospects in manufacturing cutting edge microdevices, such as lab-on-a-chips (LOCs) and microelectromechanical systems (MEMS). (orig.)

F2-laser patterning of indium tin oxide (ITO) thin film on glass substrate

International Nuclear Information System (INIS)

Xu, M.Y.; Li, J.; Herman, P.R.; Lilge, L.D.

2006-01-01

This paper reports the controlled micromachining of 100 nm thick indium tin oxide (ITO) thin films on glass substrates with a vacuum-ultraviolet 157 nm F 2 laser. Partial to complete film removal was observed over a wide fluence window from 0.49 J/cm 2 to an optimized single pulse fluence of 4.5 J/cm 2 for complete film removal. Optical microscopy, atomic force microscopy, and energy dispersive X-ray analysis show little substrate or collateral damage by the laser pulse which conserved the stoichiometry, optical transparency and electrical conductivity of ITO coating adjacent to the trenches. At higher fluence, a parallel micron sized channel can be etched in the glass substrate. The high photon energy and top-hat beam homogenized optical system of the F 2 laser opens new means for direct structuring of electrodes and microchannels in biological microfluidic systems or in optoelectronics. (orig.)

Differential distribution and association of FTO rs9939609 gene polymorphism with obesity: A cross-sectional study among two tribal populations of India with East-Asian ancestry.

Science.gov (United States)

Ningombam, Somorjit Singh; Chhungi, Varhlun; Newmei, Masan Kambo; Rajkumari, Sunanda; Devi, Naorem Kiranmala; Mondal, Prakash Ranjan; Saraswathy, Kallur Nava

2018-03-20

The fat mass and obesity associated (FTO) rs9939609 gene polymorphism is most widely studied in terms of obesity in various populations. Recently, the prevalence of obesity has been reported to be very high among the North-Eastern State of India. The major aim of the present study is to understand the extent of FTO rs9939609 gene polymorphism and its association with obesity among the two North-East Indian tribal populations with similar East Asian ancestry. Somatometric data and fasting blood sample were collected from 521 tribal individuals (258 Liangmai and 263 Mizo) of Manipur after obtaining written informed consent. Genotyping of FTO rs9939609 single nucleotide polymorphism (SNP) was done using restriction fragment length polymorphism method for PCR-amplified fragments. Both the presently studied populations were not following Hardy-Weinberg law. The prevalence of obesity and minor allele frequency of FTO rs9939609 polymorphism was found to be significantly higher among the Mizo tribe compared to that of Liangmai. The selected polymorphism was found to be significantly associated with obesity (BMI) only among the Liangmai tribe (Odds ratio-3.0; 95% CI-1.4, 6.4; p-0.003), after adjusting for age and occupation. Age-cohort wise distribution and absolute fitness analysis indicated the lower fitness of minor allele in the higher age group among the Liangmai tribe. To the best of the author's knowledge this is the first study, associating FTO rs9939609 gene polymorphism and obesity in the North-eastern Indian tribal populations with East-Asian ancestry. This study revealed the FTO rs9939609 polymorphism is observed to be associated with obesity only among the Liangmai tribe not among the Mizo tribe. The differential distribution and association observed in the two selected tribes, inhabited in a similar geographical region, could be attributed to differences in their migratory histories in terms of both route and time of settlement. Copyright © 2018 Elsevier B

Foaming of CRT panel glass powder with Na2CO3

DEFF Research Database (Denmark)

Petersen, Rasmus Rosenlund; König, Jakob; Smedskjær, Morten Mattrup

melt, while Na2O becomes incorporated into the glass structure. We have quantified the melt expansion through density measurements and the Na2O incorporation is indicated by the decrease of the glass transition temperature (Tg) of the final foam glass. The glass foaming quality depends on the foaming......Recycling of cathode ray tube (CRT) glass remains a challenging task. The CRT glass consists of four glass types fused together: Funnel-, neck-, frit- and panel glass. The three former glasses contain toxic lead oxide, and therefore have a low recycling potential. The latter on the other hand...... is lead-free, but since barium and strontium oxide are present, panel glass is incompatible with most common recycling methods. However, foam glass production is a promising approach for the recycling of panel glass waste, since the process parameters can be changed according to the glass waste...

A novel high-performance counter electrode for dye-sensitized solar cells

International Nuclear Information System (INIS)

Wang Guiqiang; Lin Ruifeng; Lin Yuan; Li Xueping; Zhou Xiaowen; Xiao Xurui

2005-01-01

A novel Pt counter electrode for dye-sensitized solar cells (DSC) was prepared by thermal decomposition of H 2 PtCl 6 on NiP-plated glass substrate. The charge-transfer kinetic properties of the platinized NiP-plated glass electrode (Pt/NiP electrode) for triiodide reduction were studied by electrochemical impedance spectroscopy. Pt/NiP electrode has the advantage over the platinized FTO conducting glass electrode (Pt/FTO electrode) in increasing the light reflectance and reducing the sheet resistance leading to improve the light harvest efficiency and the fill factor of the dye-sensitized solar cells effectively. The photon-to-current efficiency and the overall conversion efficiency of DSC using Pt/NiP counter electrode is increased by 20% and 33%, respectively, compared to that of using Pt/FTO counter electrode. Examination of the anodic dissolution and the long-term test on the variation of charge-transfer resistance indicates the good stability of the Pt/NiP electrode in the electrolyte containing iodide/triiodide

Glass Membrane For Controlled Diffusion Of Gases

Science.gov (United States)

Shelby, James E.; Kenyon, Brian E.

2001-05-15

A glass structure for controlled permeability of gases includes a glass vessel. The glass vessel has walls and a hollow center for receiving a gas. The glass vessel contains a metal oxide dopant formed with at least one metal selected from the group consisting of transition metals and rare earth metals for controlling diffusion of the gas through the walls of the glass vessel. The vessel releases the gas through its walls upon exposure to a radiation source.

Variant rs9939609 in the FTO gene is associated with body mass index among Chinese children

Directory of Open Access Journals (Sweden)

Liu Ailing

2010-09-01

Full Text Available Abstract Background Fat-mass and obesity-associated (FTO gene is a gene located in chromosome region 16q12.2. Genetic variants in FTO are associated with the obesity phenotype in European and Hispanic populations. However, this association still remains controversial in Asian population. We aimed to test the association of FTO genetic variants with obesity and obesity-related metabolic traits among children living in Beijing, China. Methods We genotyped FTO variants rs9939609 in 670 children (332 girls and 338 boys aged 8-11 years living in Beijing, and analyzed its association with obesity and obesity-related metabolic traits. Overweight and obesity were defined by age- and sex-specific BMI reference for Chinese children. Obesity-related metabolic traits included fasting plasma glucose, lipid profiles, leptin, ghrelin, adiponectin and blood pressures. Results The frequency of rs9939609 A allele was 12.2%, which was 21.9% for the heterozygote and 1.2% for the homozygote of the A allele. The obesity prevalence among the carriers of AA/AT genotypes was significantly higher than that among those with TT genotype (36.4% vs. 22.6%, P = 0.004. Compared to the carrier of TT genotype, the likelihood of obesity was 1.79 (95% confidence interval (95% CI 1.20-2.67, P = 0.004 for the carrier of AA/AT genotype, after adjustment of sex, age and puberty stages. The BMI Z-score of children with AA/AT genotype were significantly higher than that of their counterparts with the TT genotype (1.1 ± 0.1 vs. 0.8 ± 0.1, P = 0.02. The concentration of triglyceride was 1.03 ± 0.52 mmol/L among TT carrier and 1.13 ± 0.68 mmol/L among AA/AT carrier (P = 0.045. While, the concentrations of adiponectin were 18.0 ± 0.4 μg/ml among carriers of TT and 16.2 ± 0.7 μg/ml among subjects with AA/AT genotype (P = 0.03. The level of glucose marginally increased in the AA/AT genotype subjects (4.67 ± 0.40 mmol/L vs. 4.60 ± 0.35 mmol/L, P = 0.08. The evidence of association

Non-toxic invert analog glass compositions of high modulus

Science.gov (United States)

Bacon, J. F. (Inventor)

1974-01-01

Glass compositions having a Young's modulus of at least 15 million psi are described. They and a specific modulus of at least 110 million inches consist essentially of, in mols, 15 to 40% SiO2, 6 to 15% Li2O, 24 to 45% of at least two bivalent oxides selected from the group consisting of Ca, NzO, MgO and CuO; 13 to 39% of at least two trivalent oxides selected from the group consisting of Al2O3, Fe2O3, B2O3, La2O3, and Y2O3 and up to 15% of one or more tetravelent oxides selected from the group consisting of ZrO2, TiO2 and CeO2. The high modulus, low density glass compositions contain no toxic elements. The composition, glass density, Young's modulus, and specific modulus for 28 representative glasses are presented. The fiber modulus of five glasses are given.

Remediation and production of low-sludge high-level waste glasses

International Nuclear Information System (INIS)

Ramsey, W.G.; Brown, K.G.; Beam, D.C.

1994-01-01

High-level radioactive sludge will constitute 24-28 oxide weight percent of the high-level waste glass produced at the Savannah River Site. A recent melter campaign using non-radioactive, simulated feed was performed with a sludge content considerably lower than 24 percent. The resulting glass was processed and shown to have acceptable durability. However, the durability was lower than predicted by the durability algorithm. Additional melter runs were performed to demonstrate that low sludge feed could be remediated by simply adding sludge oxides. The Product Composition Control System, a computer code developed to predict the proper feed composition for production of high-level waste glass, was utilized to determine the necessary chemical additions. The methodology used to calculate the needed feed additives, the effects of sludge oxides on glass production, and the resulting glass durability are discussed

Properties and microstructure of the Ru-coated carbon nano tube counter electrode for dye-sensitized solar cells.

Science.gov (United States)

Han, Jeungjo; Yu, Byungkwan; Noh, Yunyoung; Suh, Young Joon; Kim, Moon J; Yoo, Kicheon; Ko, Min Jae; Song, Ohsung

2014-08-01

In this study, we investigated the performance of dye-sensitized solar cells (DSSCs) with the ruthenium (Ru) coated multi-walled carbon nanotube (MWCNT) on the counter electrode (CE). High purity MWCNT (0.01~0.06 g) was sprayed on glass/fluorine-doped tin oxide (FTO). Then 30 nm-thick Ru thin films were coated on a MWCNT template at low temperature by atomic layer deposition (ALD) using RuDi and O2 as precursor to prepare Ru-CNT CE and the 0.45 cm2 DSSC device of glass/FTO/TiO2/Dye (N719)/electrolyte (C6DMII, GSCN)/Ru-CNT CE was fabricated. The surface morphology of CEs and the energy conversion efficiency of the DSSC device were characterized by scanning electron microscope (SEM), high-resolution transmission electron microscope (HRTEM), and photocurrent-voltage (I-V) measurement. We confirmed that effective surface of the CE increased linearly as the amount of MWCNT spray increased and the crystallized Ru was deposited very conformally around the MWCNT nano template. Moreover, the efficiency of the DSSC increased up to 3.3% as the amount of MWCNT increased.

Effect of binder burnout on the sealing performance of glass ceramics for solid oxide fuel cells

Science.gov (United States)

Ertugrul, Tugrul Y.; Celik, Selahattin; Mat, Mahmut D.

2013-11-01

The glass ceramics composite sealants are among few materials suitable for the solid oxide fuel cells (SOFC) due to their high operating temperatures (600 °C-850 °C). The glass ceramics chemically bond to both the metallic interconnector and the ceramic electrolyte and provide a gas tight connection. A careful and several stages manufacturing procedure is required to obtain a gas tight sealing. In this study, effects of binder burnout process on the sealing performance are investigated employing commercially available glass ceramic powders. The glass ceramic laminates are produced by mixing glass ceramic powders with the organic binders and employing a tape casting method. The laminates are sandwiched between the metallic interconnectors of an SOFC cell. The burnout and subsequent sealing quality are analyzed by measuring leakage rate and final macrostructure of sealing region. The effects of heating rate, dead weight load, solid loading, carrier gas and their flow rates are investigated. It is found that sealing quality is affected from all investigated parameters. While a slower heating rate is required for a better burnout, the mass flow rate of sweep gas must be adequate for removal of the burned gas. The leakage rate is reduced to 0.1 ml min-1 with 2 °C min-1 + 1 °C min-1 heating rate, 86.25% solid loading, 200 N dead weight load and 500 ml min-1 sweep gas flow rate.

Copper oxide thin films anchored on glass substrate by sol gel spin coating technique

Science.gov (United States)

Krishnaprabha, M.; Venu, M. Parvathy; Pattabi, Manjunatha

2018-05-01

Owing to the excellent optical, thermal, electrical and photocatalytic properties, copper oxide nanoparticles/films have found applications in optoelectronic devices like solar/photovoltaic cells, lithium ion batteries, gas sensors, catalysts, magnetic storage media etc. Copper oxide is a p-type semiconductor material having a band gap energy varying from 1.2 eV-2.1 eV. Syzygium Samarangense fruit extract was used as reducing agent to synthesize copper oxide nanostructures at room temperature from 10 mM copper sulphate pentahydrate solution. The synthesized nanostructures are deposited onto glass substrate by spin coating followed by annealing the film at 200 °C. Both the copper oxide colloid and films are characterized using UV-Vis spectroscopy, field emission scanning electron microscopy (FESEM) and energy dispersive spectroscopy (EDS) techniques. Presence of 2 peaks at 500 nm and a broad peak centered around 800 nm in the UV-Vis absorbance spectra of copper oxide colloid/films is indicative of the formation of anisotropic copper oxide nanostructures is confirmed by the FESEM images which showed the presence of triangular shaped and rod shaped particles. The rod shaped particles inside island like structures were found in unannealed films whereas the annealed films contained different shaped particles with reduced sizes. The elemental analysis using EDS spectra of copper oxide nanoparticles/films showed the presence of both copper and oxygen. Electrical properties of copper oxide nanoparticles are affected due to quantum size effect. The electrical studies carried out on both unannealed and annealed copper oxide films revealed an increase in resistivity with annealing of the films.

Rapid thermal processing of nano-crystalline indium tin oxide transparent conductive oxide coatings on glass by flame impingement technology

International Nuclear Information System (INIS)

Schoemaker, S.; Willert-Porada, M.

2009-01-01

Indium tin oxide (ITO) is still the best suited material for transparent conductive oxides, when high transmission in the visible range, high infrared reflection or high electrical conductivity is needed. Current approaches on powder-based printable ITO coatings aim at minimum consumption of active coating and low processing costs. The paper describes how fast firing by flame impingement is used for effective sintering of ITO-coatings applied on glass. The present study correlates process parameters of fast firing by flame impingement with optoelectronic properties and changes in the microstructure of suspension derived nano-particulate films. With optimum process parameters the heat treated coatings had a sheet resistance below 0.5 kΩ/ □ combined with a transparency higher than 80%. To characterize the influence of the burner type on the process parameters and the coating functionality, two types of methane/oxygen burner were compared: a diffusion burner and a premixed burner

High performance sponge-like cobalt sulfide/reduced graphene oxide hybrid counter electrode for dye-sensitized solar cells

Science.gov (United States)

Huo, Jinghao; Wu, Jihuai; Zheng, Min; Tu, Yongguang; Lan, Zhang

2015-10-01

A sponge-like cobalt sulfide/reduced graphene oxide (CoS/rGO) hybrid film is deposited on fluorine doped SnO2 (FTO) glass by electrophoretic deposition and ion exchange deposition, following by sodium borohydride and sulfuric acid solution treatment. The film is used as the counter electrode of dye-sensitized solar cells (DSSCs), and is characterized by field emission scanning electron microscopy, Raman spectroscopy, cyclic voltammetry, electrochemical impedance spectroscopy and Tafel measurements. The results show that the CoS counter electrode has a sponge structure with large specific surface area, small charge-transfer resistance at the electrode/electrolyte interface. The addition of rGO further improves the electrocatalytic activity for I3- reduction, which results in the better electrocatalytic property of CoS/rGO counter electrodes than that of Pt counter electrode. Using CoS/rGO0.2 as counter electrode, the DSSC achieves a power conversion efficiency of 9.39%; which is increased by 27.93% compared with the DSSC with Pt counter electrode (7.34%).

Low melting high lithia glass compositions and methods

Science.gov (United States)

Jantzen, Carol M.; Pickett, John B.; Cicero-Herman, Connie A.; Marra, James C.

2000-01-01

The invention relates to methods of vitrifying waste and for lowering the melting point of glass forming systems by including lithia formers in the glass forming composition in significant amounts, typically from about 0.16 wt % to about 11 wt %, based on the total glass forming oxides. The lithia is typically included as a replacement for alkali oxide glass formers that would normally be present in a particular glass forming system. Replacement can occur on a mole percent or weight percent basis, and typically results in a composition wherein lithia forms about 10 wt % to about 100 wt % of the alkali oxide glass formers present in the composition. The present invention also relates to the high lithia glass compositions formed by these methods. The invention is useful for stabilization of numerous types of waste materials, including aqueous waste streams, sludge solids, mixtures of aqueous supernate and sludge solids, combinations of spent filter aids from waste water treatment and waste sludges, supernate alone, incinerator ash, incinerator offgas blowdown, or combinations thereof, geological mine tailings and sludges, asbestos, inorganic filter media, cement waste forms in need of remediation, spent or partially spent ion exchange resins or zeolites, contaminated soils, lead paint, etc. The decrease in melting point achieved by the present invention desirably prevents volatilization of hazardous or radioactive species during vitrification.

Effect of RE (Nd3+, Sm3+) oxide on structural, optical properties of Na2O-Li2O-ZnO-B2O3 glass system

Science.gov (United States)

Hivrekar, Mahesh M.; Bhoyar, D. N.; Mande, V. K.; Dhole, V. V.; Solunke, M. B.; Jadhav, K. M.

2018-05-01

Zinc borate glass activated with rare earth oxide (Nd2O3, Sm2O3) of Na2O-Li2O-ZnO-B2O3 quaternary system has been prepared successfully by melt quenching method. The nucleation and growth of RE oxide were controlled temperature range 950-1000° C and rapid cooling at room temperature. The physical, structural and optical properties were characterized by using X-ray diffraction (XRD), SEM, Ultraviolet-visible spectroscopy (UV-Vis). XRD and SEM studies confirmed the amorphous nature, surface morphology of prepared zinc borate glass. The physical parameters like density, molar volume, molar mass of Nd3+, Sm3+ doped borate glass are summarized in the present article. The optical absorption spectra along with tauc's plot are presented. The optical energy band gap increases due to the addition of rare earth oxide confirming the role of network modifier.

Association between polymorphism in the FTO gene and growth and carcass traits in pig crosses

Czech Academy of Sciences Publication Activity Database

Dvořáková, Věra; Bartenschlager, H.; Stratil, Antonín; Horák, P.; Stupka, R.; Čítek, J.; Šprysl, M.; Hrdlicová, Anna; Geidermann, H.

2012-01-01

Roč. 44, č. 13 (2012), s. 1-9 ISSN 0999-193X R&D Projects: GA ČR(CZ) GA523/06/1302; GA ČR GA523/09/0844 Institutional research plan: CEZ:AV0Z50450515 Keywords : FTO gene * pig crosses Subject RIV: GI - Animal Husbandry ; Breeding Impact factor: 2.859, year: 2012

Common SNPs in FTO gene are associated with obesity related anthropometric traits in an island population from the eastern Adriatic coast of Croatia.

Directory of Open Access Journals (Sweden)

Ge Zhang

2010-04-01

Full Text Available Multiple studies have provided compelling evidence that the FTO gene variants are associated with obesity measures. The objective of the study was to investigate whether FTO variants are associated with a broad range of obesity related anthropometric traits in an island population.We examined genetic association between 29 FTO SNPs and a comprehensive set of anthropometric traits in 843 unrelated individuals from an island population in the eastern Adriatic coast of Croatia. The traits include 11 anthropometrics (height, weight, waist circumference, hip circumference, bicondilar upper arm width, upper arm circumference, and biceps, triceps, subscapular, suprailiac and abdominal skin-fold thicknesses and two derived measures (BMI and WHR. Using single locus score tests, 15 common SNPs were found to be significantly associated with "body fatness" measures such as weight, BMI, hip and waist circumferences with P-values ranging from 0.0004 to 0.01. Similar but less significant associations were also observed between these markers and bicondilar upper arm width and upper arm circumference. Most of these significant findings could be explained by a mediating effect of "body fatness". However, one unique association signal between upper arm width and rs16952517 (P-value = 0.00156 could not be explained by this mediating effect. In addition, using a principle component analysis and conditional association tests adjusted for "body fatness", two novel association signals were identified between upper arm circumference and rs11075986 (P-value = 0.00211 and rs16945088 (P-value = 0.00203.The current study confirmed the association of common variants of FTO gene with "body fatness" measures in an isolated island population. We also observed evidence of pleiotropic effects of FTO gene on fat-free mass, such as frame size and muscle mass assessed by bicondilar upper arm width and upper arm circumference respectively and these pleiotropic effects might be

On-line redox sensors in industrial glass melting tanks

NARCIS (Netherlands)

Laimböck, P.R.; Beerkens, R.G.C.; Schaaf, van der J.; Kieffer, J.

2002-01-01

The oxidation state or partial oxygen pressure (pO2) of the glass melt influences many glass melt and glass product properties such as fining and foaming behavior, radiant heat transfer, forming characteristics via (a color-dependent) cooling rate, and the glass color of the final product. For these

Nuclear waste glass corrosion mechanisms

International Nuclear Information System (INIS)

Jantzen, C.M.

1987-04-01

Dissolution of nuclear waste glass occurs by corrosion mechanisms similar to those of other solids, e.g., metallurgical and mineralogic systems. Metallurgical phenomena such as active corrosion, passivation and immunity have been observed to be a function of the glass composition and the solution pH. Hydration thermodynamics was used to quantify the role of glass composition and its effect on the solution pH during dissolution. A wide compositional range of natural, lunar, medieval, and nuclear waste glasses, as well as some glass-ceramics were investigated. The factors observed to affect dissolution in deionized water are pertinent to the dissolution of glass in natural environments such as the groundwaters anticipated to interact with nuclear waste glass in a geologic repository. The effects of imposed pH and oxidation potential (Eh) conditions existing in natural environments on glass dissolution is described in the context of Pourbaix diagrams, pH potential diagrams, for glass

Fat Mass and Obesity-Associated (FTO Gene Polymorphisms Are Associated with Physical Activity, Food Intake, Eating Behaviors, Psychological Health, and Modeled Change in Body Mass Index in Overweight/Obese Caucasian Adults